Energetically benign synthesis of lanthanum silicate through “silica garden” route and its characterization

International Nuclear Information System (INIS)

Parmar, Kavita; Bhattacharjee, Santanu

2017-01-01

Lanthanum silicate synthesis through “silica garden” route has been reported as an alternative to energy intensive milling procedure. Under optimum conditions lanthanum chloride crystals react with water glass (sodium silicate) to produce self generating hollow lanthanum silicate precipitation tube(s) (LaSPT). The micro tubes are irregular, thick, white coloured and amorphous but are hierarchically built from smaller tubules of 10–20 nm diameters. They retain their amorphous nature on being heated up to 600 °C beyond which crystallization starts. The major phase in the LaSPT heated at 900 °C is La_2Si_2O_7. “As synthesized” LaSPT is heterogeneous and comprises non stoichiometric phases. The exterior and interior surfaces of these tubes are remarkably different in their morphology and chemical composition. LaSPT sintered at 1200 and 1300 °C show fair amount of ionic conductivity. - Graphical abstract: Lanthanum silicate precipitation tube (LaSPT) produced through ‘silica garden’ route offers a green alternative to energy intensive milling procedure. - Highlights: • La-silicate precipitation tube (LaSPT) synthesized via silica garden route. • The microtubes are irregular, thick, white coloured and amorphous. • They are hierarchically built from smaller tubules of 10–20 nm diameters. • The major phase in the LaSPT heated at 900 °C is La_2Si_2O_7. • LaSPT sintered at 1200 °C is fairly conducting.

Lanthanum additions and the toughness of ultra-high strength steels and the determination of appropriate lanthanum additions

International Nuclear Information System (INIS)

Garrison, Warren M.; Maloney, James L.

2005-01-01

Studies of commercial heats of AF1410 steel suggest that under appropriate conditions additions of rare-earth elements can significantly enhance fracture toughness. This improvement in toughness is not due to an extremely low inclusion volume fraction but is apparently due to the formation of larger and more widely spaced inclusions. The purpose of this work is to discuss our experience in using rare-earth additions to laboratory scale vacuum induction melted and subsequently vacuum arc remelted heats of ultra-high strength steels to achieve inclusion distributions similar to those observed in commercial heats modified with lanthanum additions. The results indicate that lanthanum additions of 0.015 wt.% to low sulfur steels which have been well deoxidized using carbon-vacuum deoxidation can result in lanthanum rich inclusions which are similar in size, volume fraction and spacing to those obtained in commercially produced heats of ultra-high strength steel to which lanthanum has been added. The heat of steel to which lanthanum additions of 0.015 wt.% were made had significantly higher toughness than did the heat of the same steel in which the sulfur had been gettered as small and closely spaced particles of MnS and which had an inclusion volume fraction similar to that of the heat modified by the addition of 0.015 wt.% lanthanum. This improvement in toughness was attributed to an increase in inclusion spacing. An addition of 0.06 wt.% lanthanum was excessive. Such an addition of lanthanum resulted in a huge volume fraction of large cuboidal inclusions which primarily contain lanthanum and oxygen and which are extremely detrimental to toughness

Lanthanum

Science.gov (United States)

... levels of phosphate in the blood can cause bone problems. Lanthanum is in a clsas of medications ... to your pharmacist or contact your local garbage/recycling department to learn about take-back programs in ...

The electrochemical behaviour study of La3+ ion in fused chlorides bath. The LaNi5 formation

International Nuclear Information System (INIS)

Dias, Cristiane

2002-01-01

The electrochemical behaviour of La 3+ ion was studied in fused chlorides bath, with purpose to obtain LaNi 5 formation parameters. The lanthanum reduction/reoxidation mechanism and intermetallic compound formation were investigated by cyclic voltammetry, chronopotentiommetry and galvanostatic electrodeposition. The electrolyte employed was eutectic mixture NaCl-KCl (1:1) with anhydrous LaCl 3 as solute, since 0,25 mol. L -1 up to 2 mol. L -1 , between 700 deg C and 800 deg C. The anhydrous LaCl 3 was prepared by lanthanum chloride slow dehydration with HCl flow and heating until 300 deg C. Over molybdenum, results depicted that lanthanum electrochemical behaviour was quasi-reversible and electrodeposition occurred in a charge transfer step with three electrons. In nickel, intermetallic compound formation was observed by interdiffusion. The scanning electronic microscopy (SEM-EDS) and X ray diffraction analysis indicated that layers composition depend on temperature and solute concentration in fused bath. Mainly LaNi 5 intermetallic compound was formed with LaCl 3 anhydrous concentration of 2 mol. L -1 at 750 deg C, with cathodic current density until 100 mA.cm -2 . (author)

Effects of lanthanum exposure on elemental distribution in rat brains measured by synchrotron radiation XRF

International Nuclear Information System (INIS)

Feng Liuxing; Xiao Haiqing; He Xiao; Liu Nianqing; Zhao Yuliang; Chai Zhifang; Zhang Zhiyong

2005-01-01

Rare earth elements (REEs) comprise a coherent series of 15 elements from lanthanum to lutetium and possessing very similar chemical properties. In recent decades, with the rapid increase of the exploitation of REE resources and their applications to modern industry and daily life, particularly to agriculture as fertilizer additives in China, more and more REEs are coming into environmental system as well as food chain through various ways. It has become increasingly important to obtain more information on the physiological function of REEs and their long-term biological effects on body of living beings. Epidemiological investigations found that the intelligence quotients (IQ) of children from the REE-high background regions are obviously different from that of the normal region. This indicated that REEs probably affect the function of brain. However, the mechanism is totally unknown. The contents and distributions of major and trace elements are sometimes good indicators of the physiological and pathological conditions of human and animal brains In this study, the effects of subchronic lanthanum exposure on the elemental distribution in the rat brains were studied. Wistar rats were exposed to lanthanum chloride through oral administration at O, 0.1, 2, and 40-mg/kg doses for 6 months. The elements such as Cl, K, Ca, Fe, Cu, and Zn in brain slices were identified by synchrotron radiation X-ray fluorescence analysis. Differences in two-dimensional maps of elemental distribution were noticed. Cl, Ca, and Zn were primarily concentrated in hippocampus of the controls. With the increase of the lanthanum dosage, the Ca and Zn levels were significantly decreased, while the Cu levels were significantly elevated in cortex, hippocampus and thalamus. Our results suggest that subchronic lanthanum exposure in rats appears to change elemental distribution in brain. The impact of lanthanides on brain function is not negligible.

Lanthanum Containing Polymer's Modification to PP

Institute of Scientific and Technical Information of China (English)

Dai Shaojun; Zhang Ming

2004-01-01

Polypropylene (PP)'s low impact strength limits its usages. Adding some a rare earth polymer can enhance PP's tensile strength and impact strength. Acrylic lanthanum was prepared by the reaction between lanthanum oxide and acrylic acid. The IR spectrum prove that and optimum reacting conditions are that the bulk ratio of La(AA) 3 and MMA is not less than one and temperature is about 80 ℃. Lanthanum containing Polymer were added into PP. When percent of addition only was 3%, strength were enhanced 10% , and impact strength 40%. SEM shows the compatibility of rare earth polymer and PP; lanthanum containing polymer can form physical crosslinking between PP's molecules, then every particle's surface connect with several PP molecules and the PP mechanical property were enhanced.

Corrosion and electrochemical properties of lanthanum

International Nuclear Information System (INIS)

Tomashov, N.D.; Matveeva, T.V.

The kinetics of the corrosion rate of lanthanum at 25 0 in air of different relative humidities, distilled water, sulfuric acid, hydrochloric acid, nitric acid, phosphoric acid, hydrofluoric acid, potassium hydroxide of different concentrations and at 100 0 C in distilled water and potassium hydroxide have been studied. In air at 22--100% relative humidity, the corrosion rate of lanthanum increases with time and with increasing humidity. In distilled water and in potassium hydroxide solutions, the corrosion rate of lanthanum increases with time and decreasees when the concentration of alkali exceeds 20%. With increasing concentration of the acids, the corrosion rate of lanthanum increases in hydrochloric acid and nitric acid and passes through a maximum in sulfuric acid (20%) and phosphoric acid (60%). The values of the corrosion rates of lanthanum in 40% nitric acid, 35% hydrochloric acid, 20% sulfuric acid, 60% phosphoric acid, and 40% hydrofluoric acid are 8 x 10 5 ; 4.4 x 10 4 ; 1.3 x 10 3 ; 9 g/m 2 h respectively

Complexometric determination of lanthanum and calcium in lanthanum chromite

International Nuclear Information System (INIS)

Novoselova, I.M.

1989-01-01

Methods of complexometric determination of lanthanum and calcium in lanthanum chromite, based on sequential titration of La and Ca by EDTA solution, where as an indicator eriochrome brack T with NaCl mixture in the ratio of 1:100 is used, are determined. Cr (3) effect was removed by its oxidation up to Cr (6) with perchloric acid; at first La was determined in presence of urotropine buffer, then Ca at pH 9.5-10 in presence of ammonia buffer. For reaction acceleration method of back titration of EDTA excess by zinc salt solution was used. Standard deviation in La and Ca determination is not over 0.2 and 0.1 % respectively

Effect of voltage on the characteristics of magnesium-lanthanum deposits synthesized by an electrodeposition process

Energy Technology Data Exchange (ETDEWEB)

Sahli, M. [Laboratoire de Physique Energétique, Université de Constantine 1 (Algeria); Chetehouna, K.; Gascoin, N. [INSA-CVL, Univ. Orléans, PRISME, EA 4229, F-18020, Bourges (France); Bellel, N. [Laboratoire de Physique Energétique, Université de Constantine 1 (Algeria); Tadini, P., E-mail: tadini.pietro@gmail.com [INSA-CVL, Univ. Orléans, PRISME, EA 4229, F-18020, Bourges (France)

2017-04-15

This work deals with the characterization of magnesium-lanthanum powders deposits produced with an electrodeposition technique using an aqueous solution based on magnesium chloride and lanthanum(III) nitrate. In recent years, the interest for magnesium-based alloys is growing due to their potential use as solid state systems for hydrogen storage. This work is a preliminary study on the synthesis of magnesium-lanthanum powders oriented to their later evaluation in systems for hydrogen storage. Magnesium and Lanthanum are deposited on a copper plate used as a cathode. Chemical composition, structure and morphology are investigated by EDS, XRD, FTIR and SEM. The effect of voltage on powders characteristics is studied considering three values (3, 3.5 and 4 V). EDS analysis shows the presence of three major elements (Mg, La and O) with a little amount of Cl. The weight percentages of Mg and O increase whereas the one of La decreases with the growth of voltage. Morphological characterization reveals that heterogeneous chemical structures are formed on the surface of the electrode and the size of aggregates decreases with the increase of voltage. From the results of X-ray analysis the deposits reveal the significant presence of two phases: Mg(OH){sub 2} and La(OH){sub 3}. The peaks originating from the Mg(OH){sub 2} phase has a non-monotonic behavior and those of La(OH){sub 3} phase increase with the increase of voltage. FTIR analysis confirms the presence of the two phases identified in XRD diffractograms and exhibits that their corresponding transmittance values increase for higher voltage values. - Highlights: • Synthesis of magnesium-lanthanum deposits by an electrodeposition process. • Voltage effect is investigated using different physicochemical analysis techniques (EDS, XRD, FTIR and SEM). • The EDS analysis shows the presence of three major elements (Mg, La and O) and a little amount of Cl. • Two phases, namely Mg(OH){sub 2} and La(OH){sub 3} are

Synthesis, spectroscopic characterization, solid state d.c. electrical conductivity and biological studies of some lanthanide(III chloride complexes with a heterocyclic Schiff base ligand

Directory of Open Access Journals (Sweden)

K. Mohanan

2016-07-01

Full Text Available Condensation of 2-hydroxy-1-naphthaldehyde with 2-amino-3-carboxyethyl-4,5-dimethylthiophene in 1:1 molar ratio, yielded a potentially tridentate Schiff base viz. 2-[N-(2′-hydroxy-1-naphthylideneamino]-3-carboxyethyl-4,5-dimethylthiophene (HNAT. This ligand formed complexes with lanthanum(III, cerium(III, praseodymium(III, neodymium(III, samarium(III, europium(III and gadolinium(III chloride under well defined conditions. These complexes were characterized through elemental analysis, molar conductance, magnetic moment measurements, IR, UV–Vis, FAB mass and 1H NMR spectral studies. Analytical data showed that all the metal complexes exhibited 1:1 metal–ligand ratio. Molar conductance values adequately confirmed the non-electrolytic nature of the metal complexes. The proton NMR spectral observations supplement the IR spectral assignments. The spectral data revealed that the ligand acted as neutral tridentate, coordinating to the metal ion through azomethine nitrogen, ester carbonyl and naphtholate oxygen without deprotonation. The ligand and its lanthanum(III chloride complex were subjected to XRD studies. The lanthanum(III chloride complex has undergone a facile transesterification reaction. The solid state d.c. electrical conductivity of some selected complexes were measured as a function of temperature, indicating the semiconducting nature of the metal complexes. The antimicrobial activities were examined by disk diffusion method against some pathogenic bacterial and fungal species.

Combined effects of simulated acid rain and lanthanum chloride on chloroplast structure and functional elements in rice.

Science.gov (United States)

Hu, Huiqing; Wang, Lihong; Zhou, Qing; Huang, Xiaohua

2016-05-01

Acid rain and rare earth element (REE) pollution exist simultaneously in many agricultural regions. However, how REE pollution and acid rain affect plant growth in combination remains largely unknown. In this study, the combined effects of simulated acid rain and lanthanum chloride (LaCl3) on chloroplast morphology, chloroplast ultrastructure, functional element contents, chlorophyll content, and the net photosynthetic rate (P n) in rice (Oryza sativa) were investigated by simulating acid rain and rare earth pollution. Under the combined treatment of simulated acid rain at pH 4.5 and 0.08 mM LaCl3, the chloroplast membrane was smooth, proteins on this membrane were uniform, chloroplast structure was integrated, and the thylakoids were orderly arranged, and simulated acid rain and LaCl3 exhibited a mild antagonistic effect; the Mg, Ca, Mn contents, the chlorophyll content, and the P n increased under this combined treatment, with a synergistic effect of simulated acid rain and LaCl3. Under other combined treatments of simulated acid rain and LaCl3, the chloroplast membrane surface was uneven, a clear "hole" was observed on the surface of chloroplasts, and the thylakoids were dissolved and loose; and the P n and contents of functional elements (P, Mg, K, Ca, Mn, Fe, Ni, Cu, Zn and Mo) and chlorophyll decreased. Under these combined treatments, simulated acid rain and LaCl3 exhibited a synergistic effect. Based on the above results, a model of the combined effects of simulated acid rain and LaCl3 on plant photosynthesis was established in order to reveal the combined effects on plant photosynthesis, especially on the photosynthetic organelle-chloroplast. Our results would provide some references for further understanding the mechanism of the combined effects of simulated acid rain and LaCl3 on plant photosynthesis.

Thermoelectric properties of non-stoichiometric lanthanum sulfides

International Nuclear Information System (INIS)

Shapiro, E.; Danielson, L.R.

1983-01-01

The lanthanum sulfides are promising candidate materials for high-efficiency thermoelectric applications at temperatures up to 1300 0 C. The nonstoichiometric lanthanum sulfides (LaS /SUB x/ , where 1.33 2 //rho/ can be chosen. The thermal conductivity remains approximately constant with stoichiometry, so a material with an optimum value of α 2 //rho/ should possess the optimum figure-of-merit. Data for the Seebeck coefficient and electrical resistivity of non-stoichiometric lanthanum sulfides is presented, together with structural properties of these materials

Preparation and characterization of perovskite structure lanthanum gallate and lanthanum aluminate based oxides

OpenAIRE

Li, Shuai

2009-01-01

The present work was initiated to study the synthesis and properties of lanthanum gallate based oxides as intermediate temperature electrolyte for solid oxide fuel cells. The wet chemical method, polymer complexing route, was used to prepare the precursor powders. To further investigate the polymer complexing method, it was also applied to the preparation of lanthanum aluminate based oxides.   Single perovskite phase La0.8Sr0.2Ga0.83Mg0.17O2.815 can be prepared by the polymer complexing meth...

Adsorption of lithium-lanthanum films on the (100) tungsten face

International Nuclear Information System (INIS)

Gupalo, M.S.; Smereka, T.P.; Babkin, G.V.; Palyukh, B.M.

1982-01-01

The method of contact potential difference is used to investigate combined adsorption of lithium-lanthanum on the (100) tungsten face. The data on work functions and thermal stability of mixed lithium-lanthanum films are obtained. The presence of lanthanum on the W(100) surface leads to appearance of minimum of work functions unobserved for the Li-W(100) system, minimum work functions and optimum lithium concentration in a mixed film are decreased at initial lanthanum coating increase. The presence of lanthanum on the W(100) face leads to lithium adsorption heat decrease

Nanoscale assembly of lanthanum silica with dense and porous interfacial structures.

Science.gov (United States)

Ballinger, Benjamin; Motuzas, Julius; Miller, Christopher R; Smart, Simon; Diniz da Costa, João C

2015-02-03

This work reports on the nanoscale assembly of hybrid lanthanum oxide and silica structures, which form patterns of interfacial dense and porous networks. It was found that increasing the molar ratio of lanthanum nitrate to tetraethyl orthosilicate (TEOS) in an acid catalysed sol-gel process alters the expected microporous metal oxide silica structure to a predominantly mesoporous structure above a critical lanthanum concentration. This change manifests itself by the formation of a lanthanum silicate phase, which results from the reaction of lanthanum oxide nanoparticles with the silica matrix. This process converts the microporous silica into the denser silicate phase. Above a lanthanum to silica ratio of 0.15, the combination of growth and microporous silica consumption results in the formation of nanoscale hybrid lanthanum oxides, with the inter-nano-domain spacing forming mesoporous volume. As the size of these nano-domains increases with concentration, so does the mesoporous volume. The absence of lanthanum hydroxide (La(OH)3) suggests the formation of La2O3 surrounded by lanthanum silicate.

Lanthanum deposition corresponds to white lesions in the stomach.

Science.gov (United States)

Iwamuro, Masaya; Urata, Haruo; Tanaka, Takehiro; Kawano, Seiji; Kawahara, Yoshiro; Kimoto, Katsuhiko; Okada, Hiroyuki

2018-05-23

Although lanthanum deposition in the stomach has been most frequently reported to occur as white lesions, no study has investigated whether the white lesions observed during esophagogastroduodenoscopy are truly lanthanum-related. Here, we retrospectively investigated the amount of lanthanum in endoscopic biopsy specimens. We reviewed four patients showing gastric white spots or annular whitish mucosa in the gastric white lesions (Bw) and peripheral mucosa where the white substance was not endoscopically observed (Bp) during biopsy. We also reviewed three patients with diffuse whitish mucosa and three patients with no whitish lesions. We performed scanning electron microscopy and energy dispersive X-ray spectrometry to quantify the lanthanum elements (wt%) in the biopsy specimens. The amount of lanthanum in the Bw ranged from 0.15-0.31 wt%, whereas that of Bp was 0.00-0.13 wt%. The difference was statistically significant (P < 0.05). The amount of lanthanum in the Bw, endoscopically presented with white spots or annular whitish mucosa, was significantly higher than that of no whitish lesions (0.05-0.14 wt%, P < 0.05). The amount of lanthanum was also higher in the diffuse whitish mucosa (0.21-0.23 wt%) compared with no whitish lesions (P < 0.01). This study is the first to reveal that pathological lanthanum deposition corresponds to the endoscopically observed white lesions in the gastric mucosa. Therefore, during esophagogastroduodenoscopy, physicians should pay attention to possible presence of white lesions in patients treated with oral lanthanum carbonate to ensure prompt identification of associated issues. Copyright © 2018 Elsevier GmbH. All rights reserved.

Mechanical properties of dense to porous alumina/lanthanum hexaaluminate composite ceramics

International Nuclear Information System (INIS)

Negahdari, Zahra; Willert-Porada, Monika; Pfeiffer, Carolin

2010-01-01

For development of new composite materials based on lanthanum hexaaluminate and alumina ceramics, a better understanding of the microstructure-properties relationship is essential. In this paper, attention was focused on the evaluation of mechanical properties of lanthanum hexaaluminate/alumina particulate composite. It was found out that the lanthanum hexaaluminate content plays a critical role in determination of the microstructure and mechanical properties of the composite ceramics. In situ formation of plate-like lanthanum hexaaluminate in the ceramic matrix was accompanied with formation of pores so that the microstructure shifted from dense to porous. Increasing the lanthanum hexaaluminate content up to a certain value enhanced the fracture toughness, increased the hardness, and increased the elastic modulus of the composite materials. Further increase in the lanthanum hexaaluminate content degraded the hardness as well as the elastic modulus of composite ceramics. The influence of lanthanum hexaaluminate on mechanical properties was described by means of microstructure, porosity, and intrinsic characteristics of lanthanum hexaaluminate.

Preferable adsorption of phosphate using lanthanum-incorporated porous zeolite: Characteristics and mechanism

Science.gov (United States)

He, Yinhai; Lin, Hai; Dong, Yingbo; Wang, Liang

2017-12-01

The adsorbent, where lanthanum oxide was incorporated onto porous zeolite (La-Z), of preferable adsorption towards phosphate was prepared by hydrothermal synthesis. Based on pH effect results, La-Z would effectively sequestrate phosphate over wider pH range of 3.0-7.0, alkaline conditions were unfavorable for phosphate. The adsorption of phosphate was not significantly influenced by ionic strength and by coexisting anions of chloride, nitrate and sulfate but bicarbonate showed slightly greater negative effects, indicating La-Z possessed highly selectivity to phosphate. Adsorption of phosphate could be well fitted by pseudo-second-order model and the process was mainly controlled by intra-particle diffusion. Equilibrium adsorption demonstrated that Langmuir model was more suitable than Freundlich model for description phosphate adsorption and the adsorption capacity was 17.2 mg P g-1, which exhibited 95% utilization of incorporated La. Over 95% phosphate was eliminated in real effluent treatment when the dose was 2 g L-1. The underlying mechanism for phosphate capture was probed with Zeta potential and X-ray photoelectron spectroscope analysis, and the formation of La-P inner-sphere complexation was testified to be the dominant pathway. All the results suggested that the porous zeolite-supported lanthanum oxide can serve as a promising adsorbent for phosphate removal in realistic application.

Electrochemical properties of lanthanum nitride with calcium nitride additions

International Nuclear Information System (INIS)

Lesunova, R.P.; Fishman, L.S.

1986-01-01

This paper reports on the electrochemical properties of lanthanum nitride with calcium nitride added. The lanthanum nitride was obtained by nitriding metallic lanthanum at 870 K in an ammonia stream. The product contained Cl, Pr, Nd, Sm, Fe, Ca, Cu, Mo, Mg, Al, Si, and Be. The calcium nitride was obtained by nitriding metallic calcium in a nitrogen stream. The conductivity on the LaN/C 3 N 2 system components are shown as a function of temperature. A table shows the solid solutions to be virtually electronic conductors and the lanthanum nitride a mixed conductor

Preparation of lanthanum sulfide nanoparticles by thermal decomposition of lanthanum complex

Institute of Scientific and Technical Information of China (English)

LI Peisen; LI Huanyong; JIE Wanqi

2011-01-01

γ-La2S3 nanoparticles were successfully prepared by thermal decomposition of lanthanum complex La(Et2S2CN)3·phen at low temperature. The obtained sample was characterized by the X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and element analysis. The decomposition mechanism of lanthanum complex was studied by thermogravimetric analyses (TGA). The results showed that the obtained samples were cubic phase particles with uniform sizes among 10-30 nm and γ-La2S3 was prepared by decomposition of La(Et2S2CN)3 phen via La4(Et2S2CN)3 as an intermediate product. The band gap of γ-La2S3 was 2.97 eV, which was bigger than bulk crystal because of pronounced quantum confinement effect.

Fuel cells with doped lanthanum gallate electrolyte

Science.gov (United States)

Feng, Man; Goodenough, John B.; Huang, Keqin; Milliken, Christopher

Single cells with doped lanthanum gallate electrolyte material were constructed and tested from 600 to 800°C. Both ceria and the electrolyte material were mixed with NiO powder respectively to form composite anodes. Doped lanthanum cobaltite was used exclusively as the cathode material. While high power density from the solid oxide fuel cells at 800°C was achieved. our results clearly indicate that anode overpotential is the dominant factor in the power loss of the cells. Better anode materials and anode processing methods need to be found to fully utilize the high ionic conductivity of the doped lanthanum galiate and achieve higher power density at 800°C from solid oxide fuel cells.

Fuel cells with doped lanthanum gallate electrolyte

Energy Technology Data Exchange (ETDEWEB)

Feng Man [Texas Univ., Austin, TX (United States). Center for Materials Science and Engineering; Goodenough, J.B. [Texas Univ., Austin, TX (United States). Center for Materials Science and Engineering; Huang Keqin [Texas Univ., Austin, TX (United States). Center for Materials Science and Engineering; Milliken, C. [Cerematec, Inc., Salt Lake City, UT (United States)

1996-11-01

Single cells with doped lanthanum gallate electrolyte material were constructed and tested from 600 to 800 C. Both ceria and the electrolyte material were mixed with NiO powder respectively to form composite anodes. Doped lanthanum cobaltite was used exclusively as the cathode material. While high power density from the solid oxide fuel cells at 800 C was achieved, our results clearly indicate that anode overpotential is the dominant factor in the power loss of the cells. Better anode materials and anode processing methods need to be found to fully utilize the high ionic conductivity of the doped lanthanum gallate and achieve higher power density at 800 C from solid oxide fuel cells. (orig.)

Process for obtaining cobalt and lanthanum nickelate

International Nuclear Information System (INIS)

Tapcov, V.; Samusi, N.; Gulea, A.; Horosun, I.; Stasiuc, V.; Petrenco, P.

1999-01-01

The invention relates to the process for obtaining polycrystalline ceramics of cobalt and lanthanum nickelate with the perovskite structure from coordinative hetero metallic compounds. The obtained products can be utilized in the industry in the capacity of catalysts. Summary of the invention consists in obtaining polycrystalline ceramics LaCoO 3 and LaNiO 3 with the perovskite structure by pyrolysis of the parent compounds, namely, the coordinative hetero metallic compounds of the lanthanum cobalt or lanthanum nickel. The pyrolysis of the parent compound runs during one hour at 800 C. The technical result of the invention consists in lowering the temperature of the parent compound pyrolysis containing the precise ratio of metals necessary for ceramics obtaining

Separation of lanthanum from nuclear fuel solutions by high performance liquid chromatography

International Nuclear Information System (INIS)

Lazar, G. C.; Petre, M.; Androne, G.; Benga, A.

2016-01-01

This paper presents the separation of uranium, praseodymium and lanthanum from nuclear fuel solutions by high performance liquid chromatography (HPLC). The aim of this study is to establish a minimum concentration of lanthanum which can be analyzed by high performance liquid chromatography, and also to study the effect of uranium concentration on the separation of praseodymium and lanthanum. Optimum gradient mode was established for mixture standard stoc solutions with uranium in a concentration of 1 mg/ml, praseodymium and lanthanum in a concentration range of 1-5 μg/ml from each element. These conditions were applied for the separation of lanthanum from a nuclear fuel solution in which praseodymium and lanthanum were added in a concentration of 3 μg/ml from each element. The elution behavior of lanthanum as a function of the pH and the concentration of the mobile phase, using a mixture of 1-octanesulfonic acid sodium salt with a-hidroxyisobutiric acid is presented. (authors)

The effect of lanthanum applications on drought tolerance in barley

International Nuclear Information System (INIS)

Buckingham, S.; Maheswaran, J.; Peverill, K.; Meehan, B.; Stokes, J.

1998-01-01

Full text: Glasshouse investigations carried out by the authors on both perlite and soil, have repeatedly shown that several plant species, when treated with lanthanum, retain greater amounts of moisture under water stressed conditions. Dry matter increases under water stress have been observed in some cases. Barley plants watered to 50% field capacity, and show-ing signs of water stress, yielded 18% more dry matter when treated with 5 kg/ha and 10 kg/ha of lanthanum than control plants (P<0.05). The results of these experiments suggest that increased dry matter production in crops under periods of water stress, is likely when previously treated with lanthanum. Consequently, it is conceivable that lanthanum may have potential as an agent that induces drought tolerance in grain crops, grown in low rainfall areas. Subsequent field trials using barley as a test crop at Walpeup, in the Mallee region of Victoria have shown that in a below average rainfall year, combined soil and foliar applications of lanthanum can significantly increase grain yield. This effect was not evident when barley grown on the same soil type was treated with lanthanum under above average rainfall conditions

Lanthanum trilactate: Vibrational spectroscopic study - infrared/Raman spectroscopy

Czech Academy of Sciences Publication Activity Database

Švecová, M.; Novák, Vít; Bartůněk, V.; Člupek, M.

2016-01-01

Roč. 87, Nov (2016), s. 123-128 ISSN 0924-2031 Institutional support: RVO:61388963 Keywords : lanthanum trilactate * tris(2-hydroxypropanoato-O1,O2) * lanthanum tris[2-(hydroxy-kappa O)propanoato-kappa O] * Raman spectra * infrared spectra * DFT Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.740, year: 2016

Evolution of the corrosion process of AA 2024-T3 in an alkaline NaCl solution with sodium dodecylbenzenesulfonate and lanthanum chloride inhibitors

International Nuclear Information System (INIS)

Zhou, Biner; Wang, Yishan; Zuo, Yu

2015-01-01

Highlights: • Inhibition effect of LaCl 3 and SDBS for AA 2024 in NaCl solution (pH 10) was studied. • At the beginning the active polarization behavior of the alloy changed to passivation. • The passive behavior gradually disappeared with time and pitting happened at S-phases. • The compounded inhibitors showed good inhibition but cannot totally inhibit pitting. • The adsorption of SDBS played the key role for inhibition to the corrosion process. - Abstract: The evolution of the corrosion process of AA 2024-T3 in 0.58 g L −1 NaCl solution (pH 10) with sodium dodecylbenzenesulfonate (SDBS) and lanthanum chloride inhibitors was studied with electrochemical and surface analysis methods. With the addition of the compounded LaCl 3 and SDBS inhibitors, in the early stage the polarization behavior of AA 2024-T3 changed from active corrosion to passivation, and both the general corrosion and pitting corrosion were inhibited. However, with the immersion time extended, the passive behavior gradually disappeared and pitting happened at the Cu-rich phases. After 24 h immersion, the compounded inhibitors still showed good inhibition for general corrosion, but the polarization curve again presented the characteristic similar to active polarization. The compounded inhibitors also inhibited the pitting corrosion to some extent. The acting mechanism of the inhibitors SDBS and La 3 Cl on the corrosion process of AA 2024-T3 in the test solution was discussed.

Hydrophilic block copolymer-directed growth of lanthanum hydroxide nano-particles

Energy Technology Data Exchange (ETDEWEB)

Bouyer, F.; Sanson, N.; Gerardin, C. [Laboratoire de Materiaux Catalytiques et Catalyse en Chimie Organique, UMR 5618 CNRS-ENSCM-UM1, FR 1878, Institut Gerhardt, 34 - Montpellier (France); Destarac, M. [Centre de Recherches Rhodia Aubervilliers, 93 - Aubervilliers (France)

2006-03-15

Stable hairy lanthanum hydroxide nano-particles were synthesized in water by performing hydrolysis and condensation reactions of lanthanum cations in the presence of double hydrophilic poly-acrylic acid-b-polyacrylamide block copolymers (PAA-b-PAM). In the first step, the addition of asymmetric PAA-b-PAM copolymers (M{sub w,PAA} {<=} M{sub w,PAM}) to lanthanum salt solutions, both at pH = 5.5, induces the formation of monodispersed micellar aggregates, which are predominantly isotropic. The core of the hybrid aggregates is constituted of a lanthanum polyacrylate complex whose formation is due to bidentate coordination bonding between La{sup 3+} and acrylate groups, as shown by ATR-FTIR experiments and pH measurements. The size of the micellar aggregates depends on the molecular weight of the copolymer but is independent of the copolymer to metal ratio in solution. In the second step, the hydrolysis of lanthanum ions is induced by addition of a strong base such as sodium hydroxide. Either flocculated suspensions or stable anisotropic or spherical nano-particles of lanthanum hydrolysis products were obtained depending on the metal complexation ratio [acrylate]/[La]. The variation of that parameter also enables the control of the size of the core-corona nano-particles obtained by lanthanum hydroxylation. The asymmetry degree of the copolymer was shown to influence both the size and the shape of the particles. Elongated particles with a high aspect ratio, up to 10, were obtained with very asymmetric copolymers (M{sub w,PAM}/M{sub w,PAA}{>=}10) while shorter rice grain-like particles were obtained with a less asymmetric copolymer. The asymmetry degree also influences the value of the critical metal complexation degree required to obtain stable colloidal suspensions of polymer-stabilized lanthanum hydroxide. (authors)

Cytocompatibility of a free machining titanium alloy containing lanthanum.

Science.gov (United States)

Feyerabend, Frank; Siemers, Carsten; Willumeit, Regine; Rösler, Joachim

2009-09-01

Titanium alloys like Ti6Al4V are widely used in medical engineering. However, the mechanical and chemical properties of titanium alloys lead to poor machinability, resulting in high production costs of medical products. To improve the machinability of Ti6Al4V, 0.9% of the rare earth element lanthanum (La) was added. The microstructure, the mechanical, and the corrosion properties were determined. Lanthanum containing alloys exhibited discrete particles of cubic lanthanum. The mechanical properties and corrosion resistance were slightly decreased but are still sufficient for many applications in the field of medical engineering. In vitro experiments with mouse macrophages (RAW 264.7) and human bone-derived cells (MG-63, HBDC) were performed and revealed that macrophages showed a dose response below and above a LaCl3 concentration of 200 microM, while MG-63 and HBDC tolerated three times higher concentrations without reduction of viability. The viability of cells cultured on disks of the materials showed no differences between the reference and the lanthanum containing alloy. We therefore propose that lanthanum containing alloy appears to be a good alternative for biomedical applications, where machining of parts is necessary.

Enhanced corrosion resistance of A3xx.x/SiCp composites in chloride media by La surface treatments

International Nuclear Information System (INIS)

Pardo, A.; Merino, M.C.; Arrabal, R.; Feliu, S.; Viejo, F.; Carboneras, M.

2006-01-01

The influence of silicon carbide particles (SiCp) proportion and matrix composition of aluminium metal matrix composites (A3xx.x/SiCp) modified by lanthanum-based conversion or electrolysis coating was evaluated in 3.5 wt% NaCl aerated solution. The intermetallic compounds were preferentially covered by lanthanum-based conversion coatings obtained by immersion in 50 deg. C solution of La(III) salt, and the intermetallic compounds, SiCp and aluminium matrix were covered by lanthanum electrolysis treatment. The corrosion process was studied on the basis of gravimetric tests and electrochemical impedance spectroscopy (EIS) during immersion in 3.5 wt% NaCl aerated solution. The composition of both La coating and corrosion products was analyzed before and after accelerated testing, by scanning electron microscopy (SEM), atomic force microscopy (AFM), low-angle X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) to determine the influence of surface microstructural changes on corrosion behaviour during exposure to the corrosive environment. The corrosion process was more influenced by the concentration of alloy elements in the matrix than by the proportion of SiCp reinforcement. Both lanthanum treated surfaces presented better behaviour to chloride solution corrosion than original composite surfaces without treatment; however, electrolysis afforded a higher degree of protection than the conversion treatment because the coating was more extensive

Bio-accumulation of lanthanum from lanthanum modified bentonite treatments in lake restoration

NARCIS (Netherlands)

Waajen, G.; Van Oosterhout, F.; Lürling, M.

2017-01-01

Abstract Lanthanum (La) modified bentonite (LMB) is one of the available mitigating agents used for the reduction of the phosphorus (P) recycling in eutrophic lakes. The potential toxicity of the La from LMB to aquatic organisms is a matter of concern. In this study the accumulation of La was

Silica doped with lanthanum sol–gel thin films for corrosion protection

International Nuclear Information System (INIS)

Abuín, M.; Serrano, A.; Llopis, J.; García, M.A.; Carmona, N.

2012-01-01

We present here anticorrosive silica coatings doped with lanthanum ions for the protection of metallic surfaces as an alternative to chromate (VI)-based conversion coatings. The coatings were synthesized by the sol–gel method starting from silicon alkoxides and two different lanthanum precursors: La (III) acetate hydrate and La (III) isopropoxide. Artificial corrosion tests in acid and alkaline media showed their effectiveness for the corrosion protection of AA2024 aluminum alloy sheets for coating prepared with both precursors. The X-ray absorption Near Edge Structure and X-ray Absorption Fine Structure analysis of the coatings confirmed the key role of lanthanum in the structural properties of the coating determining its anticorrosive properties. - Highlights: ► Silica sol–gel films doped with lanthanum ions were synthesized. ► Films from lanthanum-acetate and La-alkoxide were prepared for comparison purposes. ► La-acetate is an affordable chemical reactive preferred for the industry. ► Films properties were explored by scanning electron microscopy and X-Ray absorption spectroscopy. ► An alternative to anticorrosive pre-treatments for metallic surfaces is suggested.

Determination of main components in lanthanum titanates blend

International Nuclear Information System (INIS)

Sizonenko, T.N.; Timchenko, A.K.

1981-01-01

Conditions for complexonometric determination of lanthanum in the presence of titanium using the disguising of the latter are studied. A method is suggested for lanthanum and titanium determination in a blend of lanthanum titanate which is used to grow monocrystals. Sulfosalicylic acid is chosen as a disguising agent. La has been determined by complexonometric titration using EDTA with xylenol orange in urotropin. The total contents of La and Ti have been determined by titration of EDTA excess with standard solution of zinc sulfate. Ti content has been calculated from the difference between the first two determinations. Reproducibility of Ti and La determination in the blend (n=21) is characterized by the following: at 19.73% La and 57.21% Ti there are (19.72+-0.16)% La and (57.10+-0.22)% Ti, Sr equals 0.0071 and 0.0034, respectively

Evolution of the local environment of lanthanum during simplified SON68 glass leaching

International Nuclear Information System (INIS)

Jollivet, P.; Delaye, J.M.; Den Auwer, C.; Simoni, E.

2007-01-01

The evolution of the short- and medium-range local environment of lanthanum was determined by L-III-edge X-ray absorption spectroscopy (XAS) during leaching of simplified SON68-type glasses. In glass without phosphorus, lanthanum is found in a silicate environment, and its first coordination sphere comprises eight oxygen atoms at a mean distance of 2.51 angstrom. When this glass was leached at a high renewal rate, the lanthanum local environment was significantly modified: it was present at hydroxy-carbonate and silicate sites with a mean La-O distance of 2.56 angstrom, and the second neighbors consisted of La atoms instead of Si for the glass. Conversely, in the gel formed at low renewal rates, lanthanum was found in a silicate environment similar to that of the glass. In phosphorus-doped glass, lanthanum is found in a phosphate environment, although the Si/P atomic ratio is 20:1. Lanthanum is surrounded by seven oxygen atoms at a mean distance of 2.37 angstrom. When phosphorus-doped glass is leached, regardless of the leaching solution flow rate, the short- and medium-range lanthanum local environment remains almost constant; the most significant change is a 0.05 angstrom increase in the La-O distance. (authors)

Calcium and lanthanum solid base catalysts for transesterification

Science.gov (United States)

Ng, K. Y. Simon; Yan, Shuli; Salley, Steven O.

2015-07-28

In one aspect, a heterogeneous catalyst comprises calcium hydroxide and lanthanum hydroxide, wherein the catalyst has a specific surface area of more than about 10 m.sup.2/g. In another aspect, a heterogeneous catalyst comprises a calcium compound and a lanthanum compound, wherein the catalyst has a specific surface area of more than about 10 m.sup.2/g, and a total basicity of about 13.6 mmol/g. In further another aspect, a heterogeneous catalyst comprises calcium oxide and lanthanum oxide, wherein the catalyst has a specific surface area of more than about 10 m.sup.2/g. In still another aspect, a process for preparing a catalyst comprises introducing a base precipitant, a neutral precipitant, and an acid precipitant to a solution comprising a first metal ion and a second metal ion to form a precipitate. The process further comprises calcining the precipitate to provide the catalyst.

Silica doped with lanthanum sol-gel thin films for corrosion protection

Energy Technology Data Exchange (ETDEWEB)

Abuin, M. [Department of Materials Physics, Complutense University at Madrid, Avda. Complutense sn, 28004 Madrid (Spain); Serrano, A. [Glass and Ceramic Institute, CSIC, C. Kelsen 5, 28049 Madrid (Spain); Llopis, J. [Department of Materials Physics, Complutense University at Madrid, Avda. Complutense sn, 28004 Madrid (Spain); Garcia, M.A. [Glass and Ceramic Institute, CSIC, C. Kelsen 5, 28049 Madrid (Spain); IMDEA Nanoscience, Fco. Tomas y Valiente 7, 28049 Madrid (Spain); Carmona, N., E-mail: n.carmona@fis.ucm.es [Department of Materials Physics, Complutense University at Madrid, Avda. Complutense sn, 28004 Madrid (Spain)

2012-06-01

We present here anticorrosive silica coatings doped with lanthanum ions for the protection of metallic surfaces as an alternative to chromate (VI)-based conversion coatings. The coatings were synthesized by the sol-gel method starting from silicon alkoxides and two different lanthanum precursors: La (III) acetate hydrate and La (III) isopropoxide. Artificial corrosion tests in acid and alkaline media showed their effectiveness for the corrosion protection of AA2024 aluminum alloy sheets for coating prepared with both precursors. The X-ray absorption Near Edge Structure and X-ray Absorption Fine Structure analysis of the coatings confirmed the key role of lanthanum in the structural properties of the coating determining its anticorrosive properties. - Highlights: Black-Right-Pointing-Pointer Silica sol-gel films doped with lanthanum ions were synthesized. Black-Right-Pointing-Pointer Films from lanthanum-acetate and La-alkoxide were prepared for comparison purposes. Black-Right-Pointing-Pointer La-acetate is an affordable chemical reactive preferred for the industry. Black-Right-Pointing-Pointer Films properties were explored by scanning electron microscopy and X-Ray absorption spectroscopy. Black-Right-Pointing-Pointer An alternative to anticorrosive pre-treatments for metallic surfaces is suggested.

The evolution mechanism of the dislocation loops in irradiated lanthanum doped cerium oxide

International Nuclear Information System (INIS)

Miao, Yinbin; Aidhy, Dilpuneet; Chen, Wei-Ying; Mo, Kun; Oaks, Aaron; Wolf, Dieter; Stubbins, James F.

2014-01-01

Cerium dioxide, a non-radioactive surrogate of uranium dioxide, is useful for simulating the radiation responses of uranium dioxide and mixed oxide fuel (MOX). Controlled additions of lanthanum can also be used to form various levels of lattice oxide or anion vacancies. In previous transmission electron microscopy (TEM) experimental studies, the growth rate of dislocation loops in irradiated lanthanum doped ceria was reported to vary with lanthanum concentration. This work reports findings of the evolution mechanisms of the dislocation loops in cerium oxide with and without lanthanum dopants based on a combination of molecular statics and molecular dynamics simulations. These dislocation loops are found to be b=1/3〈111〉 interstitial type Frank loops. Calculations of the defect energy profiles of the dislocation loops with different structural configurations and radii reveal the basis for preference of nucleation as well as the driving force of growth. Frenkel pair evolution simulations and displacement cascade overlaps simulations were conducted for a variety of lanthanum doping conditions. The nucleation and growth processes of the Frank loop were found to be controlled by the mobility of cation interstitials, which is significantly influenced by the lanthanum doping concentration. Competition mechanisms coupled with the mobility of cation point defects were discovered, and can be used to explain the lanthanum effects observed in experiments

DISSOLUTION OF LANTHANUM FLUORIDE PRECIPITATES

Science.gov (United States)

Fries, B.A.

1959-11-10

A plutonium separatory ore concentration procedure involving the use of a fluoride type of carrier is presented. An improvement is given in the derivation step in the process for plutonium recovery by carrier precipitation of plutonium values from solution with a lanthanum fluoride carrier precipitate and subsequent derivation from the resulting plutonium bearing carrier precipitate of an aqueous acidic plutonium-containing solution. The carrier precipitate is contacted with a concentrated aqueous solution of potassium carbonate to effect dissolution therein of at least a part of the precipitate, including the plutonium values. Any remaining precipitate is separated from the resulting solution and dissolves in an aqueous solution containing at least 20% by weight of potassium carbonate. The reacting solutions are combined, and an alkali metal hydroxide added to a concentration of at least 2N to precipitate lanthanum hydroxide concomitantly carrying plutonium values.

Adsorption of lithium-lanthanum films on W (112) face

International Nuclear Information System (INIS)

Gupalo, M.S.; Smereka, T.P.; Palyukh, B.M.; Babkin, G.V.

1986-01-01

The method of contact potential difference is employed to study the electron adsorption properties (the work function phi and adsorption heat q) lithium films on a lanthanized W(112) surface. It is found that the work function of mixed lithium-lanthanum films is intermediate between phi of the summands. The presence of lanthanum on a W(112) face reduces the adsorption heat of lithium

The electrochemical behaviour study of La{sup 3+} ion in fused chlorides bath. The LaNi{sub 5} formation; Estudo do comportamento eletroquimico do ion La{sup 3+} em meio a cloretos fundidos. A formacao de LaNi{sub 5}

Energy Technology Data Exchange (ETDEWEB)

Dias, Cristiane

2002-07-01

The electrochemical behaviour of La{sup 3+} ion was studied in fused chlorides bath, with purpose to obtain LaNi{sub 5} formation parameters. The lanthanum reduction/reoxidation mechanism and intermetallic compound formation were investigated by cyclic voltammetry, chronopotentiommetry and galvanostatic electrodeposition. The electrolyte employed was eutectic mixture NaCl-KCl (1:1) with anhydrous LaCl{sub 3} as solute, since 0,25 mol. L{sup -1} up to 2 mol. L{sup -1}, between 700 deg C and 800 deg C. The anhydrous LaCl{sub 3} was prepared by lanthanum chloride slow dehydration with HCl flow and heating until 300 deg C. Over molybdenum, results depicted that lanthanum electrochemical behaviour was quasi-reversible and electrodeposition occurred in a charge transfer step with three electrons. In nickel, intermetallic compound formation was observed by interdiffusion. The scanning electronic microscopy (SEM-EDS) and X ray diffraction analysis indicated that layers composition depend on temperature and solute concentration in fused bath. Mainly LaNi{sub 5} intermetallic compound was formed with LaCl{sub 3} anhydrous concentration of 2 mol. L{sup -1} at 750 deg C, with cathodic current density until 100 mA.cm{sup -2}. (author)

Nanosized lead lanthanum titanate (PLT) ceramic powders synthesized by the oxidant peroxo method

Energy Technology Data Exchange (ETDEWEB)

Camargo, Emerson R. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod.Washingtin Luis km 235, CP 676, Sao Carlos SP 13565-9905 (Brazil)], E-mail: camargo@ufscar.br; Barrado, Cristiano M. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod.Washingtin Luis km 235, CP 676, Sao Carlos SP 13565-9905 (Brazil); Ribeiro, Caue [EMBRAPA Instrumentacao Agropecuaria, Rua XV de Novembro 1452, Sao Carlos SP 13560-970 (Brazil)], E-mail: caue@cnpdia.embrapa.br; Longo, Elson [Department of Biochemistry, Chemistry Institute of Araraquara, UNESP-Sao Paulo State University, Rua Francisco Degni, CP 355, Araraquara SP 14801-907 (Brazil)], E-mail: elson@iq.unesp.br; Leite, Edson R. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod.Washingtin Luis km 235, CP 676, Sao Carlos SP 13565-9905 (Brazil)], E-mail: derl@power.ufscar.br

2009-05-05

For the first time it is reported the synthesis of lead titanate modified with rare earth by the oxidant-peroxo method (OPM). Lanthanum was added up to 20% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of a solution of lead and lanthanum nitrate into an aqueous solution of titanium peroxo complexes. The amorphous precipitate formed was heat-treated at different temperatures in the range from 400 to 900 deg. C for crystallization. Powders were characterized by Raman spectroscopy and X-ray diffraction. Tetragonal perovskite structure was observed for the samples up to 15% of lanthanum substitution and cubic perovskite for sample with 20% of lanthanum. Crystallographic domains calculated by Scherrer equation showing a probable suppression of the crystallite growth in function of lanthanum content. It was observed shifting to lower frequencies of Raman modes in the range between 100 and 400 cm{sup -1} and the vanishing of the A1(2TO) and E(1LO) modes could be attributed to transition phase from tetragonal to cubic. Electronic microscopy image revealed that the powders annealed at height temperature are spherical with sharp size distribution.

Nanosized lead lanthanum titanate (PLT) ceramic powders synthesized by the oxidant peroxo method

International Nuclear Information System (INIS)

Camargo, Emerson R.; Barrado, Cristiano M.; Ribeiro, Caue; Longo, Elson; Leite, Edson R.

2009-01-01

For the first time it is reported the synthesis of lead titanate modified with rare earth by the oxidant-peroxo method (OPM). Lanthanum was added up to 20% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of a solution of lead and lanthanum nitrate into an aqueous solution of titanium peroxo complexes. The amorphous precipitate formed was heat-treated at different temperatures in the range from 400 to 900 deg. C for crystallization. Powders were characterized by Raman spectroscopy and X-ray diffraction. Tetragonal perovskite structure was observed for the samples up to 15% of lanthanum substitution and cubic perovskite for sample with 20% of lanthanum. Crystallographic domains calculated by Scherrer equation showing a probable suppression of the crystallite growth in function of lanthanum content. It was observed shifting to lower frequencies of Raman modes in the range between 100 and 400 cm -1 and the vanishing of the A1(2TO) and E(1LO) modes could be attributed to transition phase from tetragonal to cubic. Electronic microscopy image revealed that the powders annealed at height temperature are spherical with sharp size distribution.

Distribution of lanthanum and neodymium in Di(2-ethlhexyl) phosphoric acid and tributylphosphate

International Nuclear Information System (INIS)

Kraikaew, J.; Suparith, N.; Pruantonsai, P.

1994-01-01

Lanthanum and neodymium are among the high quantity elements in mixed rare earth from monazite processing. The popular rare earth separation process is liquid-liquid extraction. This research was carried out to study lanthanum and neodymium distribution in two extractants, di(2-ethylhexyl) phosphoric acid and tributylphosphate. The experimental results show that neodymium distributes in both extractants better than lanthanum. The distribution of both elements are higher at low acidity than at high acidity. Quick and rough investigation by calculating the ratio of distribution coefficient of neodymium to lanthanum in each extractant indicated that La-nd separation efficiency of Di(2-ethylhexyl) phosphoric acid is higher than that of tributylphosphate

Pressure behaviour of the superconducting transition temperature of lanthanum

International Nuclear Information System (INIS)

Glocker, R.

1977-01-01

The dissertation has the following chapters: 1) Introduction, 2) Fundamentals of the microscopic theory of superconductivity, 3) Calculation of the first momentum of the Eliashberg function, 4) Determination of the average values of frequency, 5) The relativistic cellular method and its application to lanthanum, 6) Results of the calculation of the electron-phonon coupling cosntants for f.c.c. lanthanum, 7) Phonon dispersion and phonon state density. (orig.) [de

Functionalization of lanthanum hydroxide nanowires by atom transfer radical polymerization

International Nuclear Information System (INIS)

Zhou Mi; Yuan Jinying; Yuan Weizhong; Yin Yingwu; Hong Xiaoyin

2007-01-01

Atom transfer radical polymerization (ATRP) has been used to prepare a core-shell hybrid nanostructure successfully: a hard core of single-crystalline lanthanum hydroxide nanowires and a soft shell of polystyrene (PS) brushes. Transmission electron microscopy (TEM) images indicated that the resulting products presented special structures and different thicknesses of polymer layers. The chemical components and grafted PS quantities of the samples were measured by Fourier transform infrared (FT-IR) spectroscopy and thermogravimetric analysis (TGA). The polymers showed narrow polydispersity, which proved that the lanthanum hydroxide nanowires initiated the 'living'/controlled polymerization of styrene. With the modifiability of lanthanum hydroxide nanowires, the solubility increased, which affords a new way to functionalize nanowires

Spectrophotometric study of the complexation equilibria of lanthanum(III) with 1,4-bis(4'-methylanilino)anthraquinone and the determination of lanthanum(III)

International Nuclear Information System (INIS)

Idriss, K.A.-R; El-Shahawy, A.S.; Sedaira, H.; Harfoush, A.A.

1985-01-01

The complexation equilibria of lanthanum(III) with 1,4-bis(4'-methylanilino)anthraquinone (Quinizarin Green) were studied spectrophotometrically in 40% V/V dimethylformamide using graphical analysis of the absorbance curves. The reaction mechanism of lanthanum with the bisarylaminoanthraquinone dye within the pH range 6 to 9.25 was demonstrated. The thermodynamic stabilities and the molar absorptivities of the complexes formed were determined. The optimum conditions for the spectrophotometric determination of La(III) with this reagent were found. (author)

Fabrication of mesoporous and high specific surface area lanthanum carbide-carbon nanotube composites

International Nuclear Information System (INIS)

Biasetto, L.; Carturan, S.; Maggioni, G.; Zanonato, P.; Bernardo, P. Di; Colombo, P.; Andrighetto, A.; Prete, G.

2009-01-01

Mesoporous lanthanum carbide-carbon nanotube composites were produced by means of carbothermal reaction of lanthanum oxide, graphite and multi-walled carbon nanotube mixtures under high vacuum. Residual gas analysis revealed the higher reactivity of lanthanum oxide towards carbon nanotubes compared to graphite. After sintering, the composites revealed a specific surface area increasing with the amount of carbon nanotubes introduced. The meso-porosity of carbon nanotubes was maintained after thermal treatment.

Effects of the wet air on the properties of the lanthanum oxide and lanthanum aluminate thin films

International Nuclear Information System (INIS)

Jun, Jin Hyung; Choi, Doo Jin

2006-01-01

Lanthanum oxide and lanthanum aluminate thin films were deposited on Si substrates. The as-grown films were stored in wet ambient and dry ambient for days and annealed after storage and also the structural and the electrical properties of the films were investigated. As the storage time increased, the La 2 O 3 films stored in wet ambient showed rapid reaction with moisture and the properties degraded. In case of the LAO films, although the thickness of the film also increased during hydration, the properties of the film did not so much changed due to the role of the incorporated aluminum. The LAO films showed better hydration resistance characteristics and so more suitable for conventional wet cleaning process in semiconductor fabrication

Improvement of acid and base resistance of nickel phosphate pigment by the addition of lanthanum cation

International Nuclear Information System (INIS)

Onoda, Hiroaki; Matsui, Hironori; Tanaka, Isao

2007-01-01

Transition metal phosphates are used as inorganic pigments, however these materials had a weak point for acid and base resistance. Because lanthanum phosphate is insoluble in acidic and basic solution, the addition of lanthanum cation was tried for the improvement of the acid and base resistance of nickel phosphate pigment. The lanthanum-doped nickel phosphates were prepared from phosphoric acid, nickel nitrate, and lanthanum nitrate solution. The additional effects of lanthanum cation were studied on the chemical composition, particle shape and size distribution, specific surface area, color, acid and base resistance of the precipitations and their thermal products

Microwave-assisted synthesis of lanthanum conversion coating on Mg-Li alloy and its corrosion resistance

International Nuclear Information System (INIS)

Song Dalei; Jing Xiaoyan; Wang Jun; Lu Shanshan; Yang Piaoping; Wang Yanli; Zhang Milin

2011-01-01

Graphical abstract: Highlights: → The method of microwave is used to synthesize lanthanum conversion coating. → Lanthanum conversion coating on Mg-Li alloy was studied. → Different conditions between room temperature and microwave were compared. → The corrosion behavior of lanthanum conversion coatings was studied. → The corrosion mechanism of lanthanum conversion coatings was studied. - Abstract: Lanthanum-based conversion coating on Mg-Li alloy has been prepared by a microwave-assisted method. X-ray diffractions (XRD) indicate that the intermetallic compounds of lanthanum are formed on Mg-Li alloy surface. Scanning electron microscopy (SEM) images show that the coating has different morphologies and special structures. The corrosion resistance was assessed by means of potentiodynamic polarization curves and electrochemical impedance spectra (EIS). The results indicate that this coating significantly reduces the corrosion rate of Mg-Li alloy in NaCl solution. A comparing experiment indicates that the coating prepared by microwave-assisted process has superior corrosion resistance to the coating obtained at room temperature.

Electrical conductivity studies of nanocrystalline lanthanum silicate synthesized by sol-gel route

International Nuclear Information System (INIS)

Nallamuthu, N.; Prakash, I.; Satyanarayana, N.; Venkateswarlu, M.

2011-01-01

Research highlights: → Nanocrystalline La 10 Si 6 O 27 material was synthesized by sol-gel method. → TG/DTA curves predicted the thermal behavior of the material. → FTIR spectra confirmed the formation of SiO 4 and La-O network in the La 10 Si 6 O 27 . → XRD patterns confirmed the formation of pure crystalline La 10 Si 6 O 27 phase. → The grain interior and the grain boundary conductivities are evaluated. - Abstract: Nanocrystalline apatite type structured lanthanum silicate (La 10 Si 6 O 27 ) sample was synthesized by sol-gel process. Thermal behavior of the dried gel of lanthanum silicate sample was studied using TG/DTA. The structural coordination of the dried gel of lanthanum silicate, calcined at various temperatures, was identified from the observed FTIR spectral results. The observed XRD patterns of the calcined dried gel were compared with the ICDD data and confirmed the formation of crystalline lanthanum silicate phase. The average crystalline size of La 10 Si 6 O 27 was calculated using the Scherrer formula and it is found to be ∼80 nm. The observed SEM images of the lanthanum silicate indicate the formation of the spherical particles and the existence of O, Si and La in the lanthanum silicate are confirmed from the SEM-EDX spectrum. The grain and grain boundary conductivities are evaluated by analyzing the measured impedance data, using winfit software, obtained at different temperatures, of La 10 Si 6 O 27 sample. Also, the observed grain and grain boundary conductivity behaviors of the La 10 Si 6 O 27 sample are analysed using brick layer model. The electrical permittivity and electrical modulus were calculated from the measured impedance data and were analyzed by fitting through the Havriliak and Negami function to describe the dielectric relaxation behavior of the nanocrystalline lanthanum silicate.

Management of hyperphosphatemia in patients with end-stage renal disease: focus on lanthanum carbonate

Directory of Open Access Journals (Sweden)

Veerle P Persy

2009-04-01

Full Text Available Veerle P Persy, Geert J Behets, Marc E De Broe, Patrick C D’HaeseLaboratory of Pathophysiology, University of Antwerp, BelgiumAbstract: Elevated serum phosphate levels as a consequence of chronic kidney disease (CKD contribute to the increased cardiovascular risk observed in dialysis patients. Protein restriction and dialysis fail to adequately prevent hyperphosphatemia, and in general treatment with oral phosphate binding agents is necessary in patients with advanced CKD. Phosphate plays a pivotal role in the development of vascular calcification, one of the factors contributing to increased cardiovascular risk in CKD patients. Treatment of hyperphosphatemia with standard calcium-based phosphate binders and vitamin D compounds can induce hypercalcemic episodes, increase the Ca × PO4 product and thus add to the risk of ectopic mineralization. In this review, recent clinical as well as experimental data on lanthanum carbonate, a novel, non-calcium, non-resin phosphate binding agent are summarized. Although lanthanum is a metal cation no aluminium-like toxicity is observed since the bioavailability of lanthanum is extremely low and its metabolism differs from that of aluminium. Clinical studies now document the absence of toxic effects of lanthanum for up to 6 years of follow-up. The effects of lanthanum on bone, vasculature and brain are discussed and put in perspective with lanthanum pharmacokinetics.Keywords: lanthanum carbonate, phosphate binding, chronic kidney disease

Electrochemical Deposition of Lanthanum Telluride Thin Films and Nanowires

Science.gov (United States)

Chi, Su (Ike); Farias, Stephen; Cammarata, Robert

2013-03-01

Tellurium alloys are characterized by their high performance thermoelectric properties and recent research has shown nanostructured tellurium alloys display even greater performance than bulk equivalents. Increased thermoelectric efficiency of nanostructured materials have led to significant interests in developing thin film and nanowire structures. Here, we report on the first successful electrodeposition of lanthanum telluride thin films and nanowires. The electrodeposition of lanthanum telluride thin films is performed in ionic liquids at room temperature. The synthesis of nanowires involves electrodepositing lanthanum telluride arrays into anodic aluminum oxide (AAO) nanoporous membranes. These novel procedures can serve as an alternative means of simple, inexpensive and laboratory-environment friendly methods to synthesize nanostructured thermoelectric materials. The thermoelectric properties of thin films and nanowires will be presented to compare to current state-of-the-art thermoelectric materials. The morphologies and chemical compositions of the deposited films and nanowires are characterized using SEM and EDAX analysis.

Properties of gallium lanthanum sulphide glass

OpenAIRE

Bastock, P.; Craig, C.; Khan, K.; Weatherby, E.; Yao, J.; Hewak, D.W.

2015-01-01

A series of gallium lanthanum sulphide (GLS) glasses has been studied in order to ascertain properties across the entire glass forming region. This is the first comprehensive study of GLS glass over a wide compositional range.

DFT Studies on Interaction between Lanthanum and Hydroxyamide

Science.gov (United States)

Pati, Anindita; Kundu, T. K.; Pal, Snehanshu

2018-03-01

Extraction and separation of individual rare earth elements has been a challenge as they are chemically very similar. Solvent extraction is the most suitable way for extraction of rare earth elements. Acidic, basic, neutral, chelating are the major classes of extractants for solvent extraction of rare earth elements. The coordination complex of chelating extractants is very selective with positively charged metal ion. Hence they are widely used. Hydroxyamide is capable of forming chelates with metal cations. In this present study interactions of hydroxyamide ligand with lanthanum have been investigated using density functional theory (DFT). Two different functional such as raB97XD and B3LYP are applied along with 6-31+G(d,p) basis set for carbon, nitrogen, hydrogen and SDD basis set for lanthanum. Stability of formed complexes has been evaluated based on calculated interaction energies and solvation energies. Frontier orbital (highest occupied molecular orbital or HOMO and lowest unoccupied molecular orbital or LUMO) energies of the molecule have also been calculated. Electronegativity, chemical hardness, chemical softness and chemical potential are also determined for these complexes to get an idea about the reactivity. From the partial charge distribution it is seen that oxygen atoms in hydroxyamide have higher negative charge. The double bonded oxygen atom present in the hydroxyamide structure has higher electron density and so it forms bond with lanthanum but the singly bonded oxygen atom in the hydroxyamide structure is weaker donor atom and so it is less available for interaction with lanthanum.

PMR investigation into complexes of lanthanum and lutetium with ethylenediaminediacetic acid

International Nuclear Information System (INIS)

Kostromina, N.A.; Novikova, L.B.

1975-01-01

Proton resonance spectra of ethylendiaminediacetic acid (EDDA) and EDDA mixtures with La and Lu as function of pH of solution was studied. Sequence of EDDA (A 2- ) protonation was established; cations H 3 A + and H 4 A 2+ were found; dissociation constants of above mentioned cations were determined. Formation of H 2 LnA 3+ , HLnA 2+ and LnA + complexes in EDDA-Ln (1:1) system was found. Difference in the bonds mobility of lanthanum and lutetium complexes was determined: lanthanum forms complexes with labile, lutetium with non-labile bonds. Information on complexes structure is collected. Acid dissociation constants of protonated complexes of lanthanum with EDDA were determined

Determination of the stability constants of lanthanum, praseodymium, europium, erbium and lutetium complexes with chloride ions; Determinacion de las constantes de estabilidad de los complejos de lantano, praseodimio, europio, erbio y lutecio con iones cloruro

Energy Technology Data Exchange (ETDEWEB)

Fernandez R, E [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

2008-07-01

The stability constants of La{sup 3+}, Pr{sup 3+}, Eu{sup 3+}, Er{sup 3+} and Lu{sup 3+} chloride complexes were determined in perchloric acid media using a liquid-liquid extraction method. The dinonyl napthalene sulfonic acid in n-heptane was used as extractant. The lanthanide (Ln) concentrations were measured by a radiochemical (Eu and Lu) and a spectrophotometric (La, Pr, and Er) methods. In the last method, xylenol orange was used for the determinations at ph 6. The stability constants of lanthanum, praseodymium, erbium and lutetium chloride complexes were determined in 2, 3 and 4 M ionic strength and europium in 1, 2 and 3 M, at 303 K. The fitting of experimental data to the equations for the calculation of the stability constants, was carry out considering both one chemical species (LnCl{sup 2+}) or two chemical species (LnCl{sup 2+} and LnCl{sub 2}{sup +}). The Specific Ion Interaction Theory was applied to the values of log {beta}{sup I}{sub Ln},{sub Cl} and the first stability constants at zero ionic strength were calculated by extrapolation. The same theory could not be applied to the log {beta}{sup I}{sub Ln},{sub 2Cl}, due to its low abundance and the values determined for the stability constants were similar. The distribution diagrams of the chemical species were obtained using the program MEDUSA and considering log {beta}{sup I}{sub Ln},{sub CI}, log {beta}{sup I}{sub Ln},{sub 2CI} values obtained in this work and the hydrolysis constants taken from the literature. The lanthanide chloride complexes are present in solution at specific conditions of ionic strength, concentration and in the absence of hydrolysis. The log {beta}{sup I}{sub Ln},{sub Cl} data were related to the charge density and the corresponding equations were obtained. These equations could be used to determine the stability constants along the lanthanide series. (Author)

Studies on the promotion of nickel—alumina coprecipitated catalysts: II. Lanthanum oxide

NARCIS (Netherlands)

Lansink Rotgerink, H.G.J.; Paalman, R.P.A.M.; van Ommen, J.G.; Ross, J.R.H.

1988-01-01

Two series of lanthanum promoted nickel—alumina catalysts have been prepared by coprecipitation of the metal nitrates, using potassium carbonate. The molar ratio between nickel and the sum of aluminium and lanthanum was kept constant at 2.5 or 9.0 within each series. The calcination and reduction of

Removal of Lanthanum (III) From Aqueous Solution Using Non-Living Water Hyacinth Roots

International Nuclear Information System (INIS)

Aly, A.; Amer, H.A.; Shawky, S.; Shawky, S.; Kandil, A.T.

2013-01-01

Removal of lanthanum (III) from aqueous solution using dried roots of water hyacinth (Eichhornia crassipes) has been investigated. The roots have been characterized by determining the ash percentage, the ph of the slurry, the elemental composition, the thermal gravimetric analysis, the surface area, the pore size, the zeta potential and ph of zero point charge. A surface area of 128 m 2 /g has been found and the micropore structure of the roots has been confirmed. Zeta potential and ph of zero point charge of the roots surfaces showed that they are positively charged within the ph range from 2 to 7.5. Sorption is rapid and depends on ph, weight of roots, concentration of lanthanum (III) and ionic strength. The sorption of lanthanum (III) was confirmed by scanning electron microscope, energy dispersive spectroscopy and the release of Ca +2 , Mg +2 and K +1 after sorption of lanthanum (III) have been indicated an ion exchange mechanism. Fourier transform infrared spectra indicated surface complexation mechanism, and sorption isotherms and kinetics were discussed. The roots were tested for removal of radioactive lanthanum ( 140 La) from simulated radioactive waste. Accepted June 2013.

Strengthening and elongation mechanism of Lanthanum-doped Titanium-Zirconium-Molybdenum alloy

Energy Technology Data Exchange (ETDEWEB)

Hu, Ping, E-mail: huping1985@126.com [School of Metallurgy Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Jinduicheng Molybdenum Co., Ltd., Xi’an 710068 (China); Hu, Bo-liang; Wang, Kuai-she; Song, Rui; Yang, Fan [School of Metallurgy Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Yu, Zhi-tao [Ruifulai Tungsten & Molybdenum Co., Ltd., Xi’an 721914 (China); Tan, Jiang-fei [School of Metallurgy Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Cao, Wei-cheng; Liu, Dong-xin; An, Geng [Jinduicheng Molybdenum Co., Ltd., Xi’an 710068 (China); Guo, Lei [Ruifulai Tungsten & Molybdenum Co., Ltd., Xi’an 721914 (China); Yu, Hai-liang [School of Mechanical, Materials and Mechatronics Engineering, University of Wollongong, NSW 2522 (Australia)

2016-12-15

The microstructural contributes to understand the strengthening and elongation mechanism in Lanthanum-doped Titanium-Zirconium-Molybdenum alloy. Lanthanum oxide particles not only act as heterogeneous nucleation core, but also act as the second phase to hinder the grain growth during sintering crystallization. The molybdenum substrate formed sub-grain under the effect of second phase when the alloy rolled to plate.

Characterization of dense lead lanthanum titanate ceramics prepared from powders synthesized by the oxidant peroxo method

Energy Technology Data Exchange (ETDEWEB)

Pinto, Alexandre H. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Departamento de Quimica, UFSCar-Universidade Federal de Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil); Souza, Flavio L., E-mail: flavio.souza@ufabc.edu.br [Centro de Ciencias Naturais e Humanas, Universidade Federal do ABC, Rua Santa Adelia 166, Bangu, Santo Andre, SP 09210-170 (Brazil); Chiquito, Adenilson J., E-mail: chiquito@df.ufscar.br [Departamento de Fisica, UFSCar-Federal University of Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil); Longo, Elson, E-mail: elson@iq.unesp.br [Instituto de Quimica de Araraquara, UNESP-Universidade Estadual Paulista, Rua Francisco Degni, CP 355 Araraquara, SP 14801-907 (Brazil); Leite, Edson R., E-mail: derl@power.ufscar.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Departamento de Quimica, UFSCar-Universidade Federal de Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil); Camargo, Emerson R., E-mail: camargo@ufscar.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Departamento de Quimica, UFSCar-Universidade Federal de Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil)

2010-12-01

Nanosized powders of lead lanthanum titanate (Pb{sub 1-x}La{sub x}TiO{sub 3}) were synthesized by means of the oxidant-peroxo method (OPM). Lanthanum was added from 5 to 30% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of lead nitrate to prepare a solution of lead and lanthanum nitrates, which was dripped into an aqueous solution of titanium peroxo complexes, forming a reactive amorphous precipitate that could be crystallized by heat treatment. Crystallized powders were characterized by FT-Raman spectroscopy and X-ray powder diffraction, showing that tetragonal perovskite structure is obtained for samples up to 25% of lanthanum and cubic perovskite for samples with 30% of lanthanum. Powders containing 25 and 30% in mol of lanthanum were calcined at 700 deg. C for 2 h, and in order to determine the relative dielectric permittivity and the phase transition behaviour from ferroelectric-to-paraelectric, ceramic pellets were prepared and sintered at 1100 or 1150 deg. C for 2 h and subjected to electrical characterization. It was possible to observe that sample containing 25% in mol of La presented a normal behaviour for the phase transition, whereas the sample containing 30% in mol of La presented a diffuse phase transition and relaxor behaviour.

Characterization of dense lead lanthanum titanate ceramics prepared from powders synthesized by the oxidant peroxo method

International Nuclear Information System (INIS)

Pinto, Alexandre H.; Souza, Flavio L.; Chiquito, Adenilson J.; Longo, Elson; Leite, Edson R.; Camargo, Emerson R.

2010-01-01

Nanosized powders of lead lanthanum titanate (Pb 1-x La x TiO 3 ) were synthesized by means of the oxidant-peroxo method (OPM). Lanthanum was added from 5 to 30% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of lead nitrate to prepare a solution of lead and lanthanum nitrates, which was dripped into an aqueous solution of titanium peroxo complexes, forming a reactive amorphous precipitate that could be crystallized by heat treatment. Crystallized powders were characterized by FT-Raman spectroscopy and X-ray powder diffraction, showing that tetragonal perovskite structure is obtained for samples up to 25% of lanthanum and cubic perovskite for samples with 30% of lanthanum. Powders containing 25 and 30% in mol of lanthanum were calcined at 700 deg. C for 2 h, and in order to determine the relative dielectric permittivity and the phase transition behaviour from ferroelectric-to-paraelectric, ceramic pellets were prepared and sintered at 1100 or 1150 deg. C for 2 h and subjected to electrical characterization. It was possible to observe that sample containing 25% in mol of La presented a normal behaviour for the phase transition, whereas the sample containing 30% in mol of La presented a diffuse phase transition and relaxor behaviour.

Signal amplification of dopamine using lanthanum hexacyanoferrate ...

Indian Academy of Sciences (India)

rare earth metal hexacyanoferrates, for e.g., lanthanum ... to facilitate the electrochemical reactions of biological molecules.9,10 In general ... bic acid and potassium hexacyanoferrate (Merck) were ... were prepared using doubly distilled water.

Leaching behavior of lanthanum, nickel and iron from spent catalyst using inorganic acids

Science.gov (United States)

Astuti, W.; Prilitasari, N. M.; Iskandar, Y.; Bratakusuma, D.; Petrus, H. T. B. M.

2018-01-01

Highly technological applications of rare earth metals (REs) and scarcity of supply have become an incentive torecover the REs from various resources, which include high grade and low grade ores, as well as recycledwaste materials. Spent hydrocracking catalyst contain lanthanum and a variety of valuable metals such as nickel and iron. This study investigated the recovery of lanthanum, nickel and iron from spent hydrocracking catalyst by leaching using various inorganic acid (sulfuric acid, hydrochloric acid, and nitric acid). The effect of acid concentration, type of acid and leaching temperature was conducted to study the leaching behavior of each valuable metal from spent-catalyst. It has been shown that it is possible to recover more than 90% of lanthanum, however the leaching efficiency of nickel and iron in this process was very low. It can be concluded that the leaching process is selective for lanthanum recovery from hydrocracking spent-catalyst.

Eutrophication management in surface waters using lanthanum modified bentonite

DEFF Research Database (Denmark)

Copetti, Diego; Finsterle, Karin; Marziali, Laura

2016-01-01

This paper reviews the scientific knowledge on the use of a lanthanum modified bentonite (LMB) to manage eutrophication in surface water. The LMB has been applied in around 200 environments worldwide and it has undergone extensive testing at laboratory, mesocosm, and whole lake scales. The availa......This paper reviews the scientific knowledge on the use of a lanthanum modified bentonite (LMB) to manage eutrophication in surface water. The LMB has been applied in around 200 environments worldwide and it has undergone extensive testing at laboratory, mesocosm, and whole lake scales....... The available data underline a high efficiency for phosphorus binding. This efficiency can be limited by the presence of humic substances and competing oxyanions. Lanthanum concentrations detected during a LMB application are generally below acute toxicological threshold of different organisms, except in low...... alkalinity waters. To date there are no indications for long-term negative effects on LMB treated ecosystems, but issues related to La accumulation, increase of suspended solids and drastic resources depletion still need to be explored, in particular for sediment dwelling organisms. Application of LMB...

High-temperature, Knudsen cell-mass spectroscopic studies on lanthanum oxide/uranium dioxide solid solutions

International Nuclear Information System (INIS)

Sunder, S.; McEachern, R.; LeBlanc, J.C.

2001-01-01

Knudsen cell-mass spectroscopic experiments were carried out with lanthanum oxide/uranium oxide solid solutions (1%, 2% and 5% (metal at.% basis)) to assess the volatilization characteristics of rare earths present in irradiated nuclear fuel. The oxidation state of each sample used was conditioned to the 'uranium dioxide stage' by heating in the Knudsen cell under an atmosphere of 10% CO 2 in CO. The mass spectra were analyzed to obtain the vapour pressures of the lanthanum and uranium species. It was found that the vapour pressure of lanthanum oxide follows Henry's law, i.e., its value is directly proportional to its concentration in the solid phase. Also, the vapour pressure of lanthanum oxide over the solid solution, after correction for its concentration in the solid phase, is similar to that of uranium dioxide. (authors)

Synthesis characterization and sintering of cobalt-doped lanthanum chromite powders for use in SOFCs

International Nuclear Information System (INIS)

Yamagata, Chieko; Mello-Castanho, Sonia R.H.

2009-01-01

Doped lanthanum chromite is a promising as interconnect material because of its good conductivity at high temperatures and its stability in oxidizing and reducing atmospheres. Perovskite oxide powders of Co-doped lanthanum chromite were synthesized by dispersing precursor metal salt solutions in a polymer matrix followed by a thermal treatment. XRD patterns showed that a highly crystalline cobalt-doped lanthanum chromite was obtained. Fine perovskite powder with a surface area of 6.15 m 2 g -1 calcined at 700 deg C for 1 h, were obtained. After the sample sintered at 1450 deg C for 3h, the powder reached high densities exceeding 97% of the theoretical density. The proposed here has proved to be a very promising technique for the synthesis of lanthanum chromite powders. (author)

Scanning Auger microscopy study of lanthanum partitioning in sphene-based glass-ceramics

International Nuclear Information System (INIS)

Hocking, W.H.; Hayward, P.J.; Watson, D.G.; Allen, G.C.

1984-01-01

Glass-ceramics are being investigated as possible hosts for the radioactive wastes that would result from recycling irradiated nuclear fuels. The partitioning of lanthanum in sphene-based glass-ceramics has been studied by scanning Auger electron microscopy for lanthanum concentrations from 0.2 to 2.0 mol.%. Sphene crystals (CaTiSiO 5 ) were located in the silica-rich glass matrix by recording digital Auger images of the calcium and titanium distributions. The sphene crystals were typically 0.5 to 5 μm in size and occupied approximately 40% of the total specimen volume. Auger spot analyses revealed that lanthanum was strongly partitioned into the sphene phase of phosphorus-free glass-ceramics; however, when a small amount of phosphorus was included in the glass-ceramic composition as a crystal nucleating agent, the lanthanum was concentrated in a third minor phase which also contained calcium, phosphorus and oxygen. Chemical shift effects in the Auger spectra of silicon, titanium and phosphorus showed evidence for electron-stimulated desorption of oxygen. (author)

Bifunctional lanthanum phosphate substrates as novel adsorbents and biocatalyst supports for perchlorate removal

International Nuclear Information System (INIS)

Sankar, Sasidharan; Prajeesh, Gangadharan Puthiya Veetil; Anupama, Vijaya Nadaraja; Krishnakumar, Bhaskaran; Hareesh, Padinhattayil; Nair, Balagopal N.; Warrier, Krishna Gopakumar; Hareesh, Unnikrishnan Nair Saraswathy

2014-01-01

Graphical abstract: Porous lanthanum phosphate substrates, obtained by an environmentally benign thermal gelation process, performed the role of dual functional sorbent facilitating perchlorate adsorption and bioremediation through the growth of perchlorate reducing microbial colonies. - Highlights: • Lanthanum phosphate monoliths as efficient perchlorate adsorbents. • And also as substrates for biofilm (perchlorate reducing bacteria) growth. • Environmentally benign thermal gelation process for substrate fabrication. • 98% adsorption efficiency for perchlorate concentrations up to 100 μg/L. • The regenerated monoliths show nearly 100% reusability. - Abstract: Porous lanthanum phosphate substrates, obtained by an environmentally benign colloidal forming process employing methyl cellulose, are reported here as excellent adsorbents of perchlorate with >98% efficiency and with 100% reusability. Additionally, the effectiveness of such substrates as biocatalyst supports that facilitate biofilm formation of perchlorate reducing microbes (Serratia marcescens NIIST 5) is also demonstrated for the first time. The adsorption of perchlorate ions is attributed to the pore structure of lanthanum phosphate substrate and the microbial attachment is primarily ascribed to its intrinsic hydrophobic property. Lanthanum phosphate thus emerges as a dual functional material that possesses an integrated adsorption/bioremediation property for the effective removal of ClO 4 − which is an increasingly important environmental contaminant

Bifunctional lanthanum phosphate substrates as novel adsorbents and biocatalyst supports for perchlorate removal

Energy Technology Data Exchange (ETDEWEB)

Sankar, Sasidharan [Materials Science and Technology Division (India); Prajeesh, Gangadharan Puthiya Veetil; Anupama, Vijaya Nadaraja [Process Engineering and Environmental Technology Division, CSIR – National Institute for Interdisciplinary Science and Technology, Industrial Estate P.O., Thiruvananthapuram 695019 (India); Krishnakumar, Bhaskaran [Process Engineering and Environmental Technology Division, CSIR – National Institute for Interdisciplinary Science and Technology, Industrial Estate P.O., Thiruvananthapuram 695019 (India); Academy of Scientific and Industrial Research (AcSIR) (India); Hareesh, Padinhattayil [Materials Science and Technology Division (India); Nair, Balagopal N. [R and D Centre, Noritake Co. Ltd., Aichi (Japan); Warrier, Krishna Gopakumar [Materials Science and Technology Division (India); Academy of Scientific and Industrial Research (AcSIR) (India); Hareesh, Unnikrishnan Nair Saraswathy, E-mail: hareesh@niist.res.in [Materials Science and Technology Division (India); Academy of Scientific and Industrial Research (AcSIR) (India)

2014-06-30

Graphical abstract: Porous lanthanum phosphate substrates, obtained by an environmentally benign thermal gelation process, performed the role of dual functional sorbent facilitating perchlorate adsorption and bioremediation through the growth of perchlorate reducing microbial colonies. - Highlights: • Lanthanum phosphate monoliths as efficient perchlorate adsorbents. • And also as substrates for biofilm (perchlorate reducing bacteria) growth. • Environmentally benign thermal gelation process for substrate fabrication. • 98% adsorption efficiency for perchlorate concentrations up to 100 μg/L. • The regenerated monoliths show nearly 100% reusability. - Abstract: Porous lanthanum phosphate substrates, obtained by an environmentally benign colloidal forming process employing methyl cellulose, are reported here as excellent adsorbents of perchlorate with >98% efficiency and with 100% reusability. Additionally, the effectiveness of such substrates as biocatalyst supports that facilitate biofilm formation of perchlorate reducing microbes (Serratia marcescens NIIST 5) is also demonstrated for the first time. The adsorption of perchlorate ions is attributed to the pore structure of lanthanum phosphate substrate and the microbial attachment is primarily ascribed to its intrinsic hydrophobic property. Lanthanum phosphate thus emerges as a dual functional material that possesses an integrated adsorption/bioremediation property for the effective removal of ClO{sub 4}{sup −} which is an increasingly important environmental contaminant.

Separation of lanthanum (3) and samarium (3) extraction with tributylphosphate in the solvent presence of solid phase

International Nuclear Information System (INIS)

Korotkevich, I.B.; Kolesnikov, A.A.; Bomshtejn, V.E.

1990-01-01

Lanthanum (3) and samarium (3) extraction from nitric acid solutions by tributylphosphate in the presence of solid phase has been investigated. An increase in samarium α-nitrate distribution factor in the presence of solid phase with a decrease in its concentration in the initial solution and with lanthanum nitrate concentration increase is detected. The greatest effect of separation is observed in samarium nitrate microregion. The method of quantitative extraction of samarium from lanthanum nitrate solutions with samarium-lanthanum separation factor exceeding 50 has been suggested

Lanthanum benzoyl acetonates: an IR and mass spectrometric study of the composition and structure

International Nuclear Information System (INIS)

Kostyuk, N.N.; Dik, T.A.; Tereshko, N.V.

2005-01-01

IR spectroscopy and mass spectrometry were used to study the structure of lanthanum chelates of benzoyl acetone (1-phenyl-1,3-butadione, HBA) of the following compositions: La(BA) 3 · EtOH, La(BA) 2 , La(BA) 2 · CH 3 CN, and La(BA) 2 · HDA, where EtOH = ethanol, HDA = nonadecanoic acid. It is demonstrated that a quasi-aromatic metalloring is formed in lanthanum chelates studied. Stable metal-containing fragments of the molecular ions of lanthanum bis- and tris-benzoylacetonate were identified [ru

Synthesis and characterization of lanthanum incorporated mesoporous molecular sieves

International Nuclear Information System (INIS)

Pesquera, C.; Gonzalez, F.; Blanco, C.; Sanchez, L.

2004-01-01

A series of mesoporous materials under reflux conditions have been synthesized with two silicon sources (fumed silica and sodium silicate) and lanthanum added. The following Si/La molar ratio was used in the samples: 100; 75; 50 and 25. The calcined products were characterized by means of X-ray diffraction, nitrogen adsorption isotherms and energy dispersive X-ray spectrometry (EDS). The BET surface area gradually decreases with an increase in the lanthanum content of the LaxMCM-41 samples. Moreover, the average pore size tends to decrease along with the increase in the La content in the samples

Physiological responses in barley to applications of lanthanum

International Nuclear Information System (INIS)

Reddy, N.; Maheswaran, J.; Peverill, K.; Meehan, B.

1998-01-01

Full text: Chinese research and glasshouse investigations carried out in Victoria by the authors have shown that several plant species, when treated with Rare Earth Elements (REEs), retain greater amounts of moisture under water stressed conditions. The physiological adaptation of the plant to retain moisture in response to REE treatment however, has not been investigated. A glasshouse trial is currently in progress to study the physiological and agronomic responses of barley (cv. Schooner) grown in pots to application of lanthanum (0, 5 and 10 kg/ha), at a concentration of 0.05%, under well-watered (field capacity) and water-deficit (25 - 30% field capacity) conditions. Lanthanum was applied both directly to the soil and as a foliar spray. The physiological measurements include, photosynthetic rate, leaf water potential, osmotic potential, relative water content, stomatal conductance and water use efficiency. Measured agronomic parameters include plant height, tiller production, leaf area development, total grain weight, total biomass, root and shoot ratio and harvest index. Analysis of plant tissue for N, P, K, Ca, Mg, Zn and La to study the relationship between application of REE and nutrient uptake is also being carried out. The paper discusses physiological and agronomic changes in barley plants in response to treatment with lanthanum, under conditions of water stress

Formulation and Assessment of a Wash-Primer Containing Lanthanum "Tannate" for Steel Temporary Protection

Science.gov (United States)

D'Alessandro, Oriana; Selmi, Gonzalo J.; Deyá, Cecilia; Di Sarli, Alejandro; Romagnoli, Roberto

2018-02-01

Tannins are polyphenols synthesized by plants and useful for the coating industry as corrosion inhibitors. In addition, lanthanum salts have a great inhibitory effect on steel corrosion. The aim of this study was to obtain lanthanum "tannate" with adequate solubility to be incorporated as the corrosion inhibitor in a wash-primer. The "tannate" was obtained from commercial "Quebracho" tannin and 0.1 M La(NO3)3. The soluble tannin was determined by the Folin-Denis reagent, while the concentration of Lanthanum was obtained by a gravimetric procedure. The protective action of "tannate" on SAE 1010 steel was evaluated by linear polarization curves and corrosion potential measurements. Lanthanum "tannate" was incorporated in a wash-primer formulation and tested by corrosion potential and ionic resistance measurements. The corrosion rate was also determined by the polarization resistance technique. Besides, the primer was incorporated in an alkyd paint system and its anticorrosion performance assessed in the salt spray cabinet and by electrochemical impedance spectroscopy. Results showed that lanthanum "tannate" primer inhibits the development of deleterious iron oxyhydroxides on the steel substrate and incorporated into a paint system had a similar behavior to the primer formulated with zinc tetroxychromate.

Separation of lanthanum (3) and neodymium (3) by tributyl phosphate extraction in the presence of solid phase

International Nuclear Information System (INIS)

Korotkevich, I.B.; Kolesnikov, A.A.; Bomshtejn, V.E.; Shikhaleeva, N.N.

1987-01-01

Lanthanum (3) and neodymium (3) extraction from nitric acid solutions by tributyl phosphate in the presence of solid phase of the element nitrates is investigated. An increase in distribution of neodymium nitrate in the presence of solid phase with the decrease in its concentration in the initial solution and with the increase in lanthanum nitrate concentration is detected. The highest effect of extractive-crystallizational separation is observed in the range of neodymium nitrate microconcentrations. A method of neodymium quantitative extraction from lanthanum nitrate solutions with neodymium - lanthanum separation coefficient exceeding 25 is suggested

Studies on the rare earth complexes with pyridine derivatives and their N-oxide(II) - Synthesis and properties of fluorescent solid complexes of samarium, europium, gadolium and terbium chlorides with 2,2'-bipyridine-N,N'-dioxide

International Nuclear Information System (INIS)

Minyu, T.; Ning, T.; Yingli, Z.; Jiyuan, B.

1985-01-01

The solid complexes of rare earth nitrates perchlorates and thiocyanates with 2,2'-bipyridine-N,N'-dioxide (bipyO/sub 2/) have been reported. However, the corresponding complexes of other rear earth chlorides have not been investigated except lanthanum, cerium and yttrium. As an extension of our previous work on the synthesis of complexes of praseodymium and neodymium chlorides wiht bipoyO/sub 2/, the authors have now prepared fluorescent solid complexes of samarium, europium, gadolium and terbium chlorides with biphyO/sub 2/, using methanol as a reaction medium. The new synthesized compounds have been identified by means of elemental analysis, infrared spectrometry, conductometry, differential thermal analysis (DTA), thermogravimetry (TG) and X-ray powder diffraction

Interfacial layers in tape cast anode-supported doped lanthanum gallate SOFC elements

Energy Technology Data Exchange (ETDEWEB)

Maffei, N.; De Silveira, G. [Materials Technology Laboratory, Natural Resources Canada, CANMET, 405 Rochester Street, Ottawa, Ontario (Canada) K1A OG3

2003-04-01

Lanthanum gallate doped with strontium and magnesium (LSGM) is a promising electrolyte system for intermediate temperature solid oxide fuel cells (SOFCs). The reported formation of interfacial layers in monolithic type SOFCs based on lanthanum gallate is of concern because of its impact on the performance of the fuel cell. Planar anode-supported SOFC elements (without the cathode) were prepared by the tape casting technique in order to determine the nature of the anode/electrolyte interface after sintering. Two anode systems were studied, one a NiO-CeO{sub 2} cermet, and the other, a modified lanthanum gallate anode containing manganese. Sintering studies were conducted at 1250, 1300, 1350, 1400 and 1450 C to determine the effect of temperature on the interfacial characteristics. Scanning electron microscopy (SEM) revealed a significant diffusion of Ni from the NiO-CeO{sub 2} anode resulting in the formation of an interfacial layer regardless of sintering temperature. Significant La diffusion from the electrolyte into the anode was also observed. In the case of the modified lanthanum gallate anode containing manganese, there was no interfacial layer formation, but a significant diffusion of Mn into the electrolyte was observed.

Preparation of lanthanum ferrite powder at low temperature

Energy Technology Data Exchange (ETDEWEB)

Andoulsi, R.; Horchani-Naifer, K.; Ferid, M., E-mail: karima_horchani@yahoo.com [Physical Chemistry Laboratory of Mineral Materials and their Applications, Hammam-Lif (Tunisia)

2012-01-15

Single lanthanum ferrite phase was successfully prepared at low processing temperature using the polymerizable complex method. To implement this work, several techniques such as differential scanning calorimetry, X-ray diffraction, Fourier Transform Infrared Spectroscopy, scanning electron microscopy and BET surface area measurements were used. Throw the obtained results, it was shown that steps of preparing the powder precursor and temperature of its calcination are critical parameters for avoiding phase segregation and obtaining pure lanthanum ferrite compound. Thus, a single perovskite phase was obtained at 600 deg C. At this temperature, the powder was found to be fine and homogeneous with an average crystallite size of 13 nm and a specific surface area of 12.5 m{sup 2}.g{sup -1}. (author)

Trimethylphosphide isomerization in lanthanum ions presence

International Nuclear Information System (INIS)

Zacharias, M.A.; Massabni, A.M.G.

1984-01-01

The integration between the trimethilphosphide and the lanthanum ions carry to the formation of solid complexes in a relation of 6:1 where the ligand is the phosphonate what is resultant of the isomerization of trimetylphosphite. By the RMN -1 H and infra-red spectra the products were characterized. (L.M.J.) [pt

The air oxidation behavior of lanthanum ion implanted zirconium at 500 deg. C

CERN Document Server

Peng, D Q; Chen, X W; Zhou, Q G

2003-01-01

The beneficial effect of lanthanum ion implantation on the oxidation behavior of zirconium at 500 deg. C has been studied. Zirconium specimens were implanted by lanthanum ions using a MEVVA source at energy of 40 keV with a fluence range from 1x10 sup 1 sup 6 to 1x10 sup 1 sup 7 ions/cm sup 2 at maximum temperature of 130 deg. C, The weight gain curves were measured after being oxidized in air at 500 deg. C for 100 min, which showed that a significant improvement was achieved in the oxidation behavior of zirconium ion implanted with lanthanum compared with that of the as-received zirconium. The valence of the oxides in the scale was analyzed by X-ray photoemission spectroscopy; and then the depth distributions of the elements in the surface of the samples were obtained by Auger electron spectroscopy. Glancing angle X-ray diffraction at 0.3 deg. incident angles was employed to examine the modification of its phase transformation because of the lanthanum ion implantation in the oxide films. It was obviously fou...

Effect of noble metal doping on the structural properties of lanthanum cobaltite

International Nuclear Information System (INIS)

Dharmadhikari, Dipti V.; Athawal, Anjali A.

2016-01-01

Pristine and Noble metal (Ag and Pd) doped lanthanum cobaltite samples have been synthesised by Hydrothermal method. Lanthanum in the A-Site and Co at B-site of Lanthanum cobaltite (LaCoO 3 ) perovskites were partially doped by silver and palladium (4%). Crystal structure analysis revealed that the hydrothermal synthesis led to the formation of pure nanocrystalline perovskite structure. Morphological analysis of the samples shows that the noble metal doping affects the morphology of the samples. Pristine sample shows spherical to oval shaped particles while the doping results in the formation of irregular shaped, spherical and rod shaped particles. Silver doping results in the agglomeration of particles. The particles were observed to be fused with each other to form rod shaped structures in case of palladium doped samples. (author)

Types of defect ordering in undoped and lanthanum-doped Bi2201 single crystals

International Nuclear Information System (INIS)

Martovitsky, V. P.

2006-01-01

Undoped and lanthanum-doped Bi2201 single crystals having a perfect average structure have been comparatively studied by x-ray diffraction. The undoped Bi2201 single crystals exhibit very narrow satellite reflections; their half-width is five to six times smaller than that of Bi2212 single crystals grown by the same technique. This narrowness indicates three-dimensional defect ordering in the former crystals. The lanthanumdoped Bi2201 single crystals with x = 0.7 and T c = 8-10 K exhibit very broad satellite reflections consisting of two systems (modulations) misoriented with respect to each other. The modulation-vector components of these two modulations are found to be q 1 = 0.237b* + 0.277c* and q 2 = 0.238b* + 0.037c*. The single crystals having a perfect average structure and a homogeneous average distribution of doping lanthanum consist of 70-to 80-A-thick layers that alternate along the c axis and have two different types of modulated superlattice. The crystals having a less perfect average structure also consist of alternating layers, but they have different lanthanum concentrations. The low value of T c in the undoped Bi2201 single crystals (9.5 K) correlates with three-dimensional defect ordering in them, and an increase in T c to 33 K upon lanthanum doping can be related to a thin-layer structure of these crystals and to partial substitution of lanthanum for the bismuth positions

AB initio energetics of lanthanum substitution in ferroelectric bismuth titanate

International Nuclear Information System (INIS)

Shah, S.H.

2012-01-01

Density functional theory based electronic structure calculations play a vital role in understanding, controlling and optimizing physical properties of materials at microscopic level. In present study system of interest is bismuth titanate (Bi/sub 4/Ti/sub 3/O/sub 12/)/(BIT) which has wide range of applications such as a high temperature piezoelectric and one of the best material for memory devices. However, it also suffers from serious issues such as oxygen vacancies which degrade its performance as a memory element and piezoelectric material. In this context, the bulk and defect properties of orthorhombic bismuth titanate (Bi/sub 4/Ti/sub 3/O/sub 12/) and bismuth lanthanum titanate (Bi/sub 3.25/La/sub 0.75/Ti/sub 3/O/sub 12/)/(BLT, x=0.75) were investigated by using first principles calculations and atomistic thermodynamics. Heats of formation, valid chemical conditions for synthesis, lanthanum substitution energies and oxygen and bismuth vacancy formation energies were computed. The study improves understanding of how native point defects and substitutional impurities influence the ferroelectric properties of these layered perovskite materials. It was found that lanthanum incorporation could occur on either of the two distinct bismuth sites in the structure and that the effect of substitution is to increase the formation energy of nearby native oxygen vacancies. The results provide direct atomistic evidence over a range of chemical conditions for the suggestion that lanthanum incorporation reduces the oxygen vacancy concentration. Oxygen vacancies contribute to ferroelectric fatigue by interacting strongly with domain walls and therefore a decrease in their concentration is beneficial. (orig./A.B.)

Phase segregation in cerium-lanthanum solid solutions

NARCIS (Netherlands)

Belliere, V.; Joorst, G; Stephan, O; de Groot, FMF; Weckhuysen, BM

2006-01-01

Electron energy-loss spectroscopy (EELS) in combination with scanning transmission electron microscopy ( STEM) reveals that the La enrichment at the surface of cerium-lanthanum solid solutions is an averaged effect and that segregation occurs in a mixed oxide phase. This separation occurs within a

Structural characterization and properties of lanthanum film as chromate replacement for tinplate

International Nuclear Information System (INIS)

Huang Xingqiao; Li Ning

2007-01-01

Sulfide-stain resistance of La-passivated, unpassivated and Cr-passivated tinplate was measured using a cysteine tarnish test. Corrosion behavior of these tinplates was investigated using electrochemical impedance spectroscopy (EIS) measurement. The morphology, composition and thickness of lanthanum film were studied by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence spectrometry (XRF), respectively. La-passivation treatment remarkably enhances sulfide-stain resistance of tinplate, and sulfide-stain resistance of La-passivated tinplate is slightly higher than that of Cr-passivated tinplate. La-passivation treatment also significantly improves corrosion protection property of tinplate. In contact with 3.5% NaCl solution, corrosion resistance of La-passivated tinplate is close to that of Cr-passivated tinplate, and in contact with 0.1 M citric-citrate buffer solution, corrosion resistance of La-passivated tinplate is higher than that of Cr-passivated tinplate. Lanthanum film is composed of spherical particles about 50-1000 nm in diameter, while most part of tinplate's surface is covered with the small particles about 50-200 nm. The film mainly consists of lanthanum and oxygen, which mainly exist as La 2 O 3 and its hydrates such as La(OH) 3 and LaOOH. The amount of lanthanum in the film is about 0.0409 g/m 2

Effect of lanthanum doping on electrical and electromechanical ...

Indian Academy of Sciences (India)

Unknown

temperature, Tc increased with the increase of lanthanum content. ... By adding oxide group softeners, hardeners and stabi- ... pressed with 2% polyvinyl alcohol as binder under a ... study are dependent on temperature and are shown in.

Lanthanum Nitrate As Electrolyte Additive To Stabilize the Surface Morphology of Lithium Anode for Lithium-Sulfur Battery.

Science.gov (United States)

Liu, Sheng; Li, Guo-Ran; Gao, Xue-Ping

2016-03-01

Lithium-sulfur (Li-S) battery is regarded as one of the most promising candidates beyond conventional lithium ion batteries. However, the instability of the metallic lithium anode during lithium electrochemical dissolution/deposition is still a major barrier for the practical application of Li-S battery. In this work, lanthanum nitrate, as electrolyte additive, is introduced into Li-S battery to stabilize the surface of lithium anode. By introducing lanthanum nitrate into electrolyte, a composite passivation film of lanthanum/lithium sulfides can be formed on metallic lithium anode, which is beneficial to decrease the reducibility of metallic lithium and slow down the electrochemical dissolution/deposition reaction on lithium anode for stabilizing the surface morphology of metallic Li anode in lithium-sulfur battery. Meanwhile, the cycle stability of the fabricated Li-S cell is improved by introducing lanthanum nitrate into electrolyte. Apparently, lanthanum nitrate is an effective additive for the protection of lithium anode and the cycling stability of Li-S battery.

Synthesis and characterization of lanthanum complex (5-choloro-8-hydroxy quinoline) bis (2-2'bipyridine) lanthanum La(Bpy)2(5-Clq)

Science.gov (United States)

Kumar, Rahul; Soam, Ankur; Bhargava, Parag

2017-05-01

Lanthanum complex, (5-choloro 8-hydroxy quinoline) bis (2-2'bipyridine) has been synthesized and characterized by different techniques. Lanthanum complex, La(Bpy)2(5-Clq) was characterized for structural, thermal and photoluminescence analysis. Structural analysis of this material was done by Fourier transformed infrared spectroscopy (FTIR) and mass spectroscopy. Thermal analysis of this material was done by thermal gravimetric analysis (TGA) and material shows the thermal stability up to 400°C. Absorption and emission spectra of the material was measured by UV-visible spectroscopy and photoluminescence spectroscopy. Solution of this material La(Bpy)2(5-Clq) in ethanol showed absorption peak at 332 nm, which may be attributed due to (π - π*) transitions. The photoluminescence spectra of La(Bpy)2(5-Clq) in ethanol solution showed intense peak at 505 nm.

Plasma spheroidization and high temperature stability of lanthanum phosphate and its compatibility with molten uranium

International Nuclear Information System (INIS)

Ananthapadmanabhan, P.V.; Sreekumar, K.P.; Thiyagarajan, T.K.; Satpute, R.U.; Krishnan, K.; Kulkarni, N.K.; Kutty, T.R.G.

2009-01-01

Lanthanum phosphate has excellent thermal stability and corrosion resistance against many molten metals and other chemically corrosive environments. Lanthanum phosphate (LaPO 4 ) was synthesized from lanthanum oxalate by thermal dissociation of the oxalate to the oxide, followed by conversion to hydrated lanthanum phosphate (LaPO 4 .0.5H 2 O). Thermal treatment of LaPO 4 .0.5H 2 O above 773 K resulted in the irreversible transformation of the hydrated phase to the stable monazite phase. Thermal and chemical stability of monazite was studied by plasma spheroidization experiments using a DC thermal plasma reactor set up. Compatibility of monazite with molten uranium was studied by thermal analysis. Results showed that monazite is thermally stable up to its melting point and also is resistant towards attack by molten uranium. Adherent coatings of LaPO 4 could be deposited onto various substrates by atmospheric plasma spray technique

Nanoscale photoelectron ionisation detector based on lanthanum hexaboride

International Nuclear Information System (INIS)

Zimmer, C.M.; Kunze, U.; Schubert, J.; Hamann, S.; Doll, T.

2011-01-01

A nanoscale ioniser is presented exceeding the limitation of conventional photoionisation detectors. It employs accelerated photoelectrons that allow obtaining molecule specificity by the tuning of ionisation energies. The material lanthanum hexaboride (LaB 6 ) is used as air stable photo cathode. Thin films of that material deposited by pulsed laser deposition (PLD) show quantum efficiency (QE) in the range of 10 -5 which is comparable to laser photo stimulation results. A careful treatment of the material yields reasonable low work functions even after surface reoxidation which opens up the possibility of using ultraviolet light emitting diodes (UV LEDs) in replacement of discharge lamps. Schematic diagram of a photoelectron ionisation detector (PeID) operating by an electron emitter based on the photoelectric effect of lanthanum hexaboride. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Plasma spheroidization and high temperature stability of lanthanum phosphate and its compatibility with molten uranium

Energy Technology Data Exchange (ETDEWEB)

Ananthapadmanabhan, P.V. [Laser and Plasma Technology Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)], E-mail: pvananth@barc.gov.in; Sreekumar, K.P.; Thiyagarajan, T.K.; Satpute, R.U. [Laser and Plasma Technology Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Krishnan, K.; Kulkarni, N.K. [Fuel Chemistry Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Kutty, T.R.G. [Radiometallurgy Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

2009-01-15

Lanthanum phosphate has excellent thermal stability and corrosion resistance against many molten metals and other chemically corrosive environments. Lanthanum phosphate (LaPO{sub 4}) was synthesized from lanthanum oxalate by thermal dissociation of the oxalate to the oxide, followed by conversion to hydrated lanthanum phosphate (LaPO{sub 4}.0.5H{sub 2}O). Thermal treatment of LaPO{sub 4}.0.5H{sub 2}O above 773 K resulted in the irreversible transformation of the hydrated phase to the stable monazite phase. Thermal and chemical stability of monazite was studied by plasma spheroidization experiments using a DC thermal plasma reactor set up. Compatibility of monazite with molten uranium was studied by thermal analysis. Results showed that monazite is thermally stable up to its melting point and also is resistant towards attack by molten uranium. Adherent coatings of LaPO{sub 4} could be deposited onto various substrates by atmospheric plasma spray technique.

Lanthanum chromite colloidal processing

International Nuclear Information System (INIS)

Setz, Luiz Fernando Grespan

2009-01-01

Lanthanum chromite (LaCrO 3 ) is currently the most studied material for applications such as solid oxide fuel cell inter connector (HTSOFC). The complexity of microstructures and geometries of HTSOFC devices, require a precise control of processing parameters to get the desired combination of properties and this, the use of techniques involving concentrated ceramic slips conformation are appropriate, therefore, is well controlled, assist in obtaining homogeneous parts, reproductive and complex geometries. Thus, studies involving the surface chemistry, the stability conditions and slips flow behaviour in the forming conditions, provide important elements for processes control in the inter connectors manufacture, where more applied settings have slots and channels for the gases passage. Thus, surface chemistry, stability and rheological behaviour of strontium and cobalt doped LaCrO 3 (La) 0.80 Sr 0. 2 0 Cr 0.92 Co 0.08 O 3 ) slips prepared with ethanol and water, were studied. The doped lanthanum chromite was produced by combustion synthesis in the IPEN/SP labs. The influence of parameters: pH (water), dispersant concentration, homogenization times and conditions, solid concentration, different ratios binder:plasticizer in the stability and the flow behavior of ceramic suspensions prepared were evaluated. The La) 0.80 Sr 0. 2 0 Cr 0.92 Co 0.08 O 3 products obtained by casting aqueous slips in a plaster mould, using alkaline pH and anionic polyelectrolyte and tapes obtained by using ethanol as a dispersant medium, after sintering at 1600 degree C/4 hours presented theoretical density > 94%, suitable for use as HTSOFC inter connector. (author)

Exchange, x-ray and IR spectral behaviour of lanthanum and praseodymium exchanged zeolite X

International Nuclear Information System (INIS)

Das, D.; Upreti, M.C.

1995-01-01

Exchange behaviour of lanthanum and praseodymium ions in zeolite X involves three steps: preferential exchange, intrazeolitic exchange and irreversible exchange. At room temperature , higher exchange has been observed with La(III) than with Pr(III) which is attributed to the smaller hydrosphere of lanthanum than praseodymium. IR spectra of these zeolites in KBr pellets show a shift in the major Si-O stretching vibration of 972 cm -1 to higher frequencies. Their x-ray diffraction patterns remain unchanged except a large decrease of the line intensities caused by the absorption of x-rays by heavy La(III) and Pr(III) ions. The present study reports the preparation and physicochemical properties of lanthanum and praseodymium exchanged zeolite X. (author). 12 refs., 3 figs., 3 tabs

Removing Phosphorus from Aqueous Solutions Using Lanthanum Modified Pine Needles.

Directory of Open Access Journals (Sweden)

Xianze Wang

Full Text Available The renewable pine needles was used as an adsorbent to remove phosphorus from aqueous solutions. Using batch experiments, pine needles pretreated with alkali-isopropanol (AI failed to effectively remove phosphorus, while pine needles modified with lanthanum hydroxide (LH showed relatively high removal efficiency. LH pine needles were effective at a wide pH ranges, with the highest removal efficiency reaching approximately 85% at a pH of 3. The removal efficiency was kept above 65% using 10 mg/L phosphorus solutions at desired pH values. There was no apparent significant competitive behavior between co-existing anions of sulfate, nitrate, and chloride (SO4(2-, NO3(- and Cl(-; however, CO3(2- exhibited increased interfering behavior as concentrations increased. An intraparticle diffusion model showed that the adsorption process occurred in three phases, suggesting that a boundary layer adsorption phenomena slightly affected the adsorption process, and that intraparticle diffusion was dominant. The adsorption process was thermodynamically unfavorable and non-spontaneous; temperature increases improved phosphorus removal. Total organic carbon (TOC assays indicated that chemical modification reduced the release of soluble organic compounds from 135.6 mg/L to 7.76 mg/L. This new information about adsorption performances provides valuable information, and can inform future technological applications designed to remove phosphorus from aqueous solutions.

Hydrothermal synthesis and crystal structure of a new lanthanum(III coordination polymer with fumaric acid

Directory of Open Access Journals (Sweden)

Hayet Anana

2015-05-01

Full Text Available The title compound, poly[diaquatris(μ4-but-2-enedioato(μ2-but-2-enedioic aciddilanthanum(III], [La2(C4H2O43(C4H4O4(H2O2]n, was synthesized by the reaction of lanthanum chloride pentahydrate with fumaric acid under hydrothermal conditions. The asymmetric unit comprises an LaIII cation, one and a half fumarate dianions (L2−, one a half-molecule of fumaric acid (H2L and one coordinated water molecule. Each LaIII cation has the same nine-coordinate environment and is surrounded by eight O atoms from seven distinct fumarate moieties, including one protonated fumarate unit and one water molecule in a distorted tricapped trigonal–prismatic environment. The LaO8(H2O polyhedra centres are edge-shared through three carboxylate bridges of the fumarate ligand, forming chains in three dimensions to construct the MOF. The crystal structure is stabilized by O—H...O hydrogen-bond interactions between the coordinated water molecule and the carboxylate O atoms, and also between oxygen atoms of fumaric acid

Lake responses following lanthanum-modified bentonite clay (Phoslock) application: an analysis of water column lanthanum data from 16 case study lakes

NARCIS (Netherlands)

Spears, B.M.; Lürling, M.F.L.L.W.; Yasseri, S.; Castro-Castellon, A.T.; Gibbs, M.; Meis, S.; McDonald, C.; McIntosh, J.; Sleep, D.; Oosterhout, van F.

2013-01-01

Phoslock is a lanthanum (La) modified bentonite clay that is being increasingly used as a geo-engineering tool for the control of legacy phosphorus (P) release from lake bed sediments to overlying waters. This study investigates the potential for negative ecological impacts from elevated La

On dependence of stability of lanthanum complexes with aminopolycarboxylic acids on the complex structure

International Nuclear Information System (INIS)

Poluehktov, N.S.; Meshkova, S.B.; Danilkovich, M.M.; Topilova, Z.M.

1985-01-01

Regularities in changes of stability constants of lanthanum complexes with aminopolycarboxylic acids (APA) versus their structure are studied, The stability of lathanum-APA complexes depends mainly on the number of carboxyl groups in a ligand molecule. At that, the highest stability constant is characteristic of a complex with a ligand, containing 3 nitrogen atoms and 5 carboxyl groups, in the presenoe of which the lanthanum ion coordination sphere gets satupated. The oxyethy group introduction into a ligand molecule also improves the lanthanum complex stability but to a lesser degree than during the introduction of a carboxyl group. The number of nitrogen atoms in a ligand polecule affects insignificantly the complex stability constant value, and the elongation of a chain of CH 2 groups, separating nitrogen atoms, reduces the constant to a -0.6 power

Order parameters in lanthanum gallate lightly doped with manganese and paramagnetic resonance

Science.gov (United States)

Vazhenin, V. A.; Potapov, A. P.; Artyomov, M. Yu.; Guseva, V. B.

2010-09-01

The Cr3+ centers have been revealed, transitions at room temperature have been identified, and spin Hamiltonian parameters have been determined for the Cr3+ and Fe3+ triclinic centers in lanthanum gallate lightly doped with manganese. The principal axes of the fourth-rank fine-structure tensor for the Fe3+ triclinic centers have been established and used to determine the order parameters, i.e., the angles of rotation of oxygen octahedra of lanthanum gallate with respect to the perovskite structure. The order parameter in the rhombohedral phase has been estimated.

Textile Dye Removal from Aqueous Solution using Modified Graphite Waste/Lanthanum/Chitosan Composite

Science.gov (United States)

Kusrini, E.; Wicaksono, B.; Yulizar, Y.; Prasetyanto, EA; Gunawan, C.

2018-03-01

We investigated various pre-treatment processes of graphite waste using thermal, mechanical and chemical methods. The aim of this work is to study the performance of modified graphite waste/lanthanum/chitosan composite (MG) as adsorbent for textile dye removal from aqueous solution. Effect of graphite waste resources, adsorbent size and lanthanum concentration on the dye removal were studied in batch experiments. Selectivity of MG was also investigated. Pre-heated graphite waste (NMG) was conducted at 80°C for 1 h, followed by mechanical crushing of the resultant graphite to 75 μm particle size, giving adsorption performance of ˜58%, ˜67%, ˜93% and ˜98% of the model dye rhodamine B (concentration determined by UV-vis spectroscopy at 554 nm), methyl orange (464 nm), methylene blue (664 nm) and methyl violet (580 nm), respectively from aqueous solution. For this process, the system required less than ˜5 min for adsorbent material to be completely saturated with the adsorbate. Further chemical modification of the pre-treated graphite waste (MG) with lanthanum (0.01 – V 0.03 M) and chitosan (0.5% w/w) did not improve the performance of dye adsorption. Under comparable experimental conditions, as those of the ‘thermal-mechanical-pre-treated-only’ (NMG), modification of graphite waste (MG) with 0.03 M lanthanum and 0.5% w/w chitosan resulted in ˜14%, ˜47%, ˜72% and ˜85% adsorption of rhodamine B, methyl orange, methylene blue and methyl violet, respectively. Selective adsorption of methylene blue at most to ˜79%, followed by methyl orange, methyl violet and rhodamine B with adsorption efficiency ˜67, ˜38, and ˜9% sequentially using MG with 0.03 M lanthanum and 0.5% w/w chitosan.

XPS characterisation of in situ treated lanthanum oxide and hydroxide using tailored charge referencing and peak fitting procedures

International Nuclear Information System (INIS)

Sunding, M.F.; Hadidi, K.; Diplas, S.; Lovvik, O.M.; Norby, T.E.; Gunnaes, A.E.

2011-01-01

Highlights: → Gold particles deposited in vacuum as energy reference for insulating samples in XPS. → Separation of La 3d and MNN peaks in XP spectra acquired with Al Kα radiation. → We describe the spectral differences between lanthanum oxide and lanthanum hydroxide. → A doublet in O 1s of La 2 O 3 is ascribed to two distinct oxygen sites in the crystal. - Abstract: A technique is described for deposition of gold nanoparticles under vacuum, enabling consistent energy referencing of X-ray photoelectron spectra obtained from lanthanum hydroxide La(OH) 3 and in situ treated lanthanum oxide La 2 O 3 powders. A method is also presented for the separation of the overlapping lanthanum 3d and MNN peaks in X-ray photoelectron spectra acquired with Al Kα radiation. The lower satellite intensity in La(OH) 3 compared to La 2 O 3 is related to the higher ionicity of the La-O bond in the former compared to the latter compound. The presence of an additional peak in the valence band spectrum of the hydroxide compared to the oxide is attributed to the O-H bond as indicated by density functional theory based calculations. A doublet in the O 1s peak of lanthanum oxide is associated to the presence of two distinct oxygen sites in the crystal structure of this compound.

Electrochemical corrosion of lanthanum chromite and yttrium chromite in coal slag

Energy Technology Data Exchange (ETDEWEB)

Marchant, D.D.; Bates, J.L.

1981-01-01

Lanthanum chromites have long been considered as electrodes for magnetohydrodynamic (MHD) generator channels. These chromites, when doped with divalent ions such as Ca, Mg or Sr, have adequate electronic and electrical conductivity (2), and melting points greater than 2500/sup 0/K. However, above approx. 1850/sup 0/K, selective vapor loss of chromium results in the formation of a La/sub 2/O/sub 3/ phase. The La/sub 2/O/sub 3/ is hydroscopic at room temperature, resulting in a large volume change and loss of mechanical integrity when exposed to H/sub 2/O. The analogous yttrium chromites have thermal and electrical properties similar to that for the lanthanum chromites. Although vapor loss of Cr results in the formation of Y/sub 2/O/sub 3/, this oxide does not hydrate. Corrosion studies of yttrium chromite compositions show that doped YCrO/sub 3/ may be a viable MHD electrode. An electrochemical corrosion study of both magnesium-doped lanthanum and yttrium chromites in synthetic coal slag electrolytes is described. Possible chemical and electrochemical degradation phenomena, as well as the relative rates of corrosion are emphasized.

Phase transformations in lead zirconate-titanate doped with lanthanum

Energy Technology Data Exchange (ETDEWEB)

Ishchuk, V M; Morozov, E M

1979-07-01

Presented are the results of studies on the character of phase transitions of the lead-lanthanum zirconate-titanate (LLZT) system. The replacement of lead by lanthanum leads to the expansion of the region of antisegnetoelectric (ASE) states of solid solutions of lead zirconate-titanate (LZT) in the direction of PbTiO/sub 3/ concentration growth. An intermediate region is revealed between segnetoelectric (SE) and ASE states, material properties in which depend on their prehistory: annealed samples are in the ASE state, whereas the application of electric field exceeding some critical value induces the SE state. A family of phase diagrams obtained at consequent replacement of lead by lanthanum permits to identify phase states in any series of LLZT with a constant ratio of Zr:Ti, in the x/65/35 series in particular. Thermally depolarized state of materials of this series at x<6.5 is shown to be antisegnetoelectric at all the temperatures below the Curie point Tsub(c), and heating causes phase transition of ASE..-->..PE (paraelectric state) at Tsub(c). Polarized samples being heated, a successiveness of phase transitions of SE..-->..ASE takes place at T/sub 0/, and that of ASE reversible PE at Tsub(C) (Tsub(0)..ASE phase transition in the LZT system.

XPS characterisation of in situ treated lanthanum oxide and hydroxide using tailored charge referencing and peak fitting procedures

Energy Technology Data Exchange (ETDEWEB)

Sunding, M.F., E-mail: m.f.sunding@fys.uio.no [Department of Physics, University of Oslo, P.O. Box 1048 Blindern, NO-0316 Oslo (Norway); Hadidi, K. [Department of Physics, University of Oslo, P.O. Box 1048 Blindern, NO-0316 Oslo (Norway); Diplas, S. [Department of Chemistry and Centre for Material Science and Nanotechnology (SMN), University of Oslo, P.O. Box 1033 Blindern, NO-0315 Oslo (Norway); SINTEF Materials and Chemistry, P.O. Box 124 Blindern, NO-0314 Oslo (Norway); Lovvik, O.M. [Department of Physics, University of Oslo, P.O. Box 1048 Blindern, NO-0316 Oslo (Norway); SINTEF Materials and Chemistry, P.O. Box 124 Blindern, NO-0314 Oslo (Norway); Norby, T.E. [Department of Chemistry and Centre for Material Science and Nanotechnology (SMN), University of Oslo, P.O. Box 1033 Blindern, NO-0315 Oslo (Norway); Gunnaes, A.E. [Department of Physics, University of Oslo, P.O. Box 1048 Blindern, NO-0316 Oslo (Norway)

2011-07-15

Highlights: {yields} Gold particles deposited in vacuum as energy reference for insulating samples in XPS. {yields} Separation of La 3d and MNN peaks in XP spectra acquired with Al K{alpha} radiation. {yields} We describe the spectral differences between lanthanum oxide and lanthanum hydroxide. {yields} A doublet in O 1s of La{sub 2}O{sub 3} is ascribed to two distinct oxygen sites in the crystal. - Abstract: A technique is described for deposition of gold nanoparticles under vacuum, enabling consistent energy referencing of X-ray photoelectron spectra obtained from lanthanum hydroxide La(OH){sub 3} and in situ treated lanthanum oxide La{sub 2}O{sub 3} powders. A method is also presented for the separation of the overlapping lanthanum 3d and MNN peaks in X-ray photoelectron spectra acquired with Al K{alpha} radiation. The lower satellite intensity in La(OH){sub 3} compared to La{sub 2}O{sub 3} is related to the higher ionicity of the La-O bond in the former compared to the latter compound. The presence of an additional peak in the valence band spectrum of the hydroxide compared to the oxide is attributed to the O-H bond as indicated by density functional theory based calculations. A doublet in the O 1s peak of lanthanum oxide is associated to the presence of two distinct oxygen sites in the crystal structure of this compound.

Lanthanum Deposition in the Stomach in the Absence of Helicobacter pylori Infection.

Science.gov (United States)

Iwamuro, Masaya; Urata, Haruo; Tanaka, Takehiro; Kawano, Seiji; Kawahara, Yoshiro; Kimoto, Katsuhiko; Okada, Hiroyuki

2018-03-15

In this case report, we describe two patients who showed a diffusely whitish mucosa in the posterior wall and the lesser curvature of the gastric body. The patients were serologically- and histopathologically-negative for Helicobacter pylori. Random biopsy specimens from the stomach revealed no regenerative changes, intestinal metaplasia, and/or foveolar hyperplasia in either of the patients. Although lanthanum deposition in the gastric mucosa has been reported to occur in close association with H. pylori-associated gastritis, our patients tested negative for H. pylori. These cases suggest that lanthanum deposition presents as whitish lesions in the gastric body in H. pylori-negative patients.

Properties of lanthanum hexaboride a compilation

CERN Document Server

Fisher, D J

2013-01-01

Lanthanum hexaboride is useful because it possesses a high melting point (2210C), a low work function, one of the highest known electron emissivities, and is stable in vacuum. This volume summarises the extant data on the properties of this material, including the: bulk modulus, conductivity, crystal structure, Debye temperature, defect structure, elastic constants, electronic structure, emissivity, Fermi surface, hardness, heat capacity, magnetoresistance, reflectivity, resistivity, specific heat, surface structure, thermal conductivity, thermoelectric power, toughness and work function. The

Lake responses following lanthanum-modified bentonite clay (Phoslock®) application: an analysis of water column lanthanum data from 16 case study lakes.

Science.gov (United States)

Spears, Bryan M; Lürling, Miquel; Yasseri, Said; Castro-Castellon, Ana T; Gibbs, Max; Meis, Sebastian; McDonald, Claire; McIntosh, John; Sleep, Darren; Van Oosterhout, Frank

2013-10-01

Phoslock(®) is a lanthanum (La) modified bentonite clay that is being increasingly used as a geo-engineering tool for the control of legacy phosphorus (P) release from lake bed sediments to overlying waters. This study investigates the potential for negative ecological impacts from elevated La concentrations associated with the use of Phoslock(®) across 16 case study lakes. Impact-recovery trajectories associated with total lanthanum (TLa) and filterable La (FLa) concentrations in surface and bottom waters were quantified over a period of up to 60 months following Phoslock(®) application. Both surface and bottom water TLa and FLa concentrations were 0.8 mEq L(-1)), but higher (up to 0.12 mg L(-1)) in lakes characterised by very low alkalinity. The effects of elevated La(3+) concentrations following Phoslock(®) applications in lakes of very low alkalinity requires further evaluation. The implications for the use of Phoslock(®) in eutrophication management are discussed. Copyright © 2013 Elsevier Ltd. All rights reserved.

Room temperature synthesis of high temperature stable lanthanum phosphate–yttria nano composite

International Nuclear Information System (INIS)

Sankar, Sasidharan; Raj, Athira N.; Jyothi, C.K.; Warrier, K.G.K.; Padmanabhan, P.V.A.

2012-01-01

Graphical abstract: A facile aqueous sol–gel route involving precipitation–peptization mechanism followed by electrostatic stabilization is used for synthesizing nanocrystalline composite containing lanthanum phosphate and yttria. Highlights: ► A novel lanthanum phosphate–Y 2 O 3 nano composite is synthesized for the first time using a modified facile sol gel process. ► The composite becomes crystalline at 600 °C and X-ray diffraction pattern is indexed for monoclinic LaPO 4 and cubic yttria. ► The composite synthesized was tested up to 1300 °C and no reaction between the phases of the constituents is observed with the morphologies of the phases being retained. -- Abstract: A facile aqueous sol–gel route involving precipitation–peptization mechanism followed by electrostatic stabilization is used for synthesizing nanocrystalline composite containing lanthanum phosphate and yttria. Lanthanum phosphate (80 wt%)–yttria (20 wt%) nano composite (LaPO 4 –20%Y 2 O 3 ), has an average particle size of ∼70 nm after heat treatment of precursor at 600 °C. TG–DTA analysis reveals that stable phase of the composite is formed on heating the precursor at 600 °C. The TEM images of the composite show rod shape morphology of LaPO 4 in which yttria is acquiring near spherical shape. Phase identification of the composite as well as the phase stability up to 1300 °C was carried out using X-ray diffraction technique. With the phases being stable at higher temperatures, the composite synthesized should be a potential material for high temperature applications like thermal barrier coatings and metal melting applications.

Structural consideration with respect to the thermal stability of a new platinum supported lanthanum-alumina catalyst

International Nuclear Information System (INIS)

Oudet, F.; Bordes, E.; Courtine, P.; Maxant, G.; Lambert, C.; Guerlet, J.P.

1987-01-01

The influence of lanthanum aluminate, LaAlO 3 , on the thermal stability of both alumina and platinum supported alumina catalysts is investigated. In the case of alumina, the stabilization is interpreted in terms of structural coherence between δ-Al 2 O 3 and a three-fold superstructure of LaAlO 3 . The addition of LaAlO 3 , is shown to increase both the dispersion and the resistance to sintering of the platinum supported alumina catalyst. Moreover, lanthanum hexa-aluminate (La-β-Al 2 O 3 ) is present in the platinum catalyst fired at 1150 0 C. These observations are assumed to result for the epitaxial relations between platinum and the lanthanum-alumina support. 23 refs.; 8 figs.; 2 tabs

Investigation of paramagnetic saturation in lanthanum manganese nitrate

NARCIS (Netherlands)

Flokstra, Jakob; Meijer, H.C.; Bots, G.J.C.; Verheij, W.A.; van der Marel, L.C.

1973-01-01

Paramagnetic saturation of lanthanum manganese nitrate, La2Mn3(NO3)12·24H2O, has been investigated at liquid He temperatures in a static as well as a dynamical way. With the aid of the molecular-field theory the Casimir and Du Pré dispersion and absorption curves are adapted explicitly to the

Deposition barium titanate (BaTiO3) doped lanthanum with chemical solution deposition

International Nuclear Information System (INIS)

Iriani, Y.; Nurhadi, N.; Jamaludin, A.

2016-01-01

Deposition of Barium Titanate (BaTiO 3 ) thin films used Chemical Solution Deposition (CSD) method and prepared with spin coater. BaTiO 3 is doped with lanthanum, 1%, 2%, and 3%. The thermal process use annealing temperature 900°C and holding time for 3 hours. The result of characterization with x-ray diffraction (XRD) equipment show that the addition of La 3+ doped on Barium Titanate caused the change of angle diffraction.The result of refine with GSAS software shows that lanthanum have been included in the structure of BaTiO 3 . Increasing mol dopant La 3+ cause lattice parameter and crystal volume become smaller. Characterization result using Scanning Electron Microscopy (SEM) equipment show that grain size (grain size) become smaller with increasing mole dopant (x) La 3+ . The result of characterization using Sawyer Tower methods show that all the samples (Barium Titanante and Barium Titanate doped lanthanum) are ferroelectric material. Increasing of mole dopant La 3+ cause smaller coercive field and remanent polarization increases. (paper)

Eucalyptus tolerance mechanisms to lanthanum and cerium: subcellular distribution, antioxidant system and thiol pools.

Science.gov (United States)

Shen, Yichang; Zhang, Shirong; Li, Sen; Xu, Xiaoxun; Jia, Yongxia; Gong, Guoshu

2014-12-01

Guanglin 9 (Eucalyptus grandis × Eucalyptus urophlla) and Eucalyptus grandis 5 are two eucalyptus species which have been found to grow normally in soils contaminated with lanthanum and cerium, but the tolerance mechanisms are not clear yet. In this study, a pot experiment was conducted to investigate the tolerance mechanisms of the eucalyptus to lanthanum and cerium. Cell walls stored 45.40-63.44% of the metals under lanthanum or cerium stress. Peroxidase and catalase activities enhanced with increasing soil La or Ce concentrations up to 200 mg kg(-1), while there were no obvious changes in glutathione and ascorbate concentrations. Non-protein thiols concentrations increased with increasing treatment levels up to 200 mg kg(-1), and then decreased. Phytochelatins concentrations continued to increase under La or Ce stress. Therefore, the two eucalyptus species are La and Ce tolerant plants, and the tolerance mechanisms include cell wall deposition, antioxidant system response, and thiol compound synthesis. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fabrication of Polycrystalline Lanthanum Manganite (La0.99 Mn0.01 O3) Powder and Fibres by Electrospinning Method

International Nuclear Information System (INIS)

Yin Yin Win; That Htar Lwin; Than Than Win; Yin Maung Maung; Ko Ko Kyaw Soe

2011-12-01

Lanthanum manganite (La0.99 Mn0.01 O3) powder have been prepared by using pyrolysis methods. Lanthanum manganite fibres were successfully fabricated by electro-spinning utilizing precursors. Polycrystalline perovskite structure lanthanum manganite powder and fibres showed that the grain size and crystal grain increased significantly with the increase in calcination temperature. A variety of techniques (SEM, FT-IR and TG-DTA) were employed to study the morphology and fibre quality, crystal structure, and thermal analysis of La0.99 Mn0.01 O3 specimen respectively.

The Catalytic Activity of Modified Zeolite Lanthanum on the Catalytic Cracking of Al-Duara Atmospheric Distillation Residue

Directory of Open Access Journals (Sweden)

Karim Khalifa Esgair

2016-03-01

Full Text Available Atmospheric residue fluid catalytic cracking was selected as a probe reaction to test the catalytic performance of modified NaY zeolites and prepared NaY zeolites. Modified NaY zeolites have been synthesized by simple ion exchange methods. Three samples of modified zeolite Y have been obtained by replacing the sodium ions in the original sample with lanthanum and the weight percent added are 0.28, 0.53, and 1.02 respectively. The effects of addition of lanthanum to zeolite Y in different weight percent on the cracking catalysts were investigated using an experimental laboratory plant scale of fluidized bed reactor. The experiments have been performed with weight hourly space velocity (WHSV range of 6 to 24 h-1, and the range of temperature from 450 to 510 oC. The activity of the catalyst with 1.02 wt% lanthanum has been shown to be much greater than that of the sample parent NaY. Also it was observed that the addition of the lanthanum causes an increase in the thermal stability of the zeolite.

Stability constant of the lanthanum complex with humic acid

International Nuclear Information System (INIS)

Jimenez R, M.; Solache R, M. J.

2008-01-01

The work described here is a study on the formation of trivalent lanthanum complex with humic acid. Commercial humic acid was purified and then characterized by various analytical techniques. The stability constant determined by a radiochemical method has a worth of log β La , AHA = 13.6. (Author)

Revised energy levels of singly ionized lanthanum

Science.gov (United States)

Güzelçimen, Feyza; Tonka, Mehdi; Uddin, Zaheer; Bhatti, Naveed Anjum; Windholz, Laurentius; Kröger, Sophie; Başar, Gönül

2018-05-01

Based on the experimental wavenumbers of 344 spectral lines from calibrated Fourier transform (FT) spectra as well as wavenumbers of 81 lines from the wavelength tables from literature, the energy of 115 fine structure levels of singly ionized lanthanum has been revised by weighted global fits. The classifications of the lines are provided by numerous previous investigations of lanthanum by different spectroscopic methods and authors. For the high accurate determination of the center of gravity wavenumbers from the experimental spectrum, the hyperfine constants of the involved levels have been taken into account, if possible. For the 94 levels with known hyperfine constants the accuracy of energy values is better than 0.01 cm-1. For 34 levels the magnetic dipole hyperfine constants A have been determined from FT spectra as part of this work. For four of these 34 levels even electric quadrupole hyperfine constants B could be estimated. For levels, which have experimentally unknown hyperfine constants and which are connected only by lines not found in the FT spectra but taken from literature, the uncertainties of energy values are about a factor of 10 higher. A list of all revised level energies together with a compilation of hyperfine structure data is given as well as a list of all lines used.

Microstructured fibers with high lanthanum oxide glass core for nonlinear applications

Science.gov (United States)

Kobelke, J.; Schuster, K.; Litzkendorf, D.; Schwuchow, A.; Kirchhof, J.; Bartelt, H.; Tombelaine, V.; Leproux, P.; Couderc, V.; Labruyere, A.

2009-05-01

We demonstrate a low loss microstructured fiber (MOF) with a high nonlinear glass core and silica holey cladding. The substitution of mostly used silica as core material of microstructured fibers by lanthanum oxide glass promises a high nonlinear conversion efficiency for supercontinuum (SC) generation. The glass composition is optimized in terms of thermochemical and optical requirements. The glass for the MOF core has a high lanthanum oxide concentration (10 mol% La2O3) and a good compatibility with the silica cladding. This is performed by adding a suitable alumina concentration up to 20 mol%. The lanthanum oxide glass preform rods were manufactured by melting technique. Besides purity issues the material homogeneity plays an important role to achieve low optical loss. The addition of fluorides allows the better homogenization of the glass composition in the preform volume by refining. The minimum attenuation of an unstructured fiber drawn from this glass is about 0.6 dB/m. It is mostly caused by decreasing of scattering effects. The microstructured silica cladding allows the considerable shifting of dispersive behavior of the MOF for an optimal pump light conversion. The MOF shows zero dispersion wavelengths (ZDW) of 1140 nm (LP01 mode) and 970 nm (LP11 mode). The supercontinuum generation was investigated with a 1064 nm pump laser (650 ps). It shows a broad band emission between 500 nm and 2200 nm.

Preparation, characterization and optical properties of Lanthanum-(nanometer MCM-41) composite materials

International Nuclear Information System (INIS)

Zhai, Q. Z.; Wang, P.

2008-01-01

Nanometer MCM-41 molecular sieve was prepared under a base condition by using cetyltrimethylammonium bromide as template and tetraethyl orthosilicate as silica source by means of hydrothermal method. Lanthanum(III) was incorporated into the nanometer MCM-41 by a liquid phase grafting method. The prepared nano composite materials were characterized by means of powder X-ray diffraction, spectrophotometric analysis, Fourier transform infrared spectroscopy, low temperature nitrogen adsorption-desorption technique, solid diffuse reflectance absorption spectra and luminescence. The powder X-ray diffraction studies show that the nanometer MCM-41 molecular sieve is successfully prepared. The highly ordered meso porous two-dimensional hexagonal channel structure and framework of the support MCM-41 is retained intact in the prepared composite material La-(nanometer MCM-41). The spectrophotometric analysis indicates that lanthanum exists in the prepared nano composite materials. The Fourier transform infrared spectra indicate that the framework of the MCM-41 molecular sieve still remains in the prepared nano composite materials and some framework vibration peaks show blue shifts relative to those of the MCM-41 molecular sieve. The low temperature nitrogen adsorption-desorption indicates that the guest locales in the channel of the molecular sieve. Compared with bulk lanthanum oxide, the guest in the channel of the molecular sieve has smaller particle size and shows a significant blue shift of optical absorption band in solid diffuse reflectance absorption spectra. The observed blue shift in the solid state diffuse reflectance absorption spectra of the lanthanum-(nanometer MCM-41) sample show the obvious stereoscopic confinement effect of the channel of the host on the guest, which further indicates the successful encapsulation of the guest in the host. The La-(nanometer MCM-41) sample shows luminescence

The rare earth element (REE) lanthanum (La) induces hormesis in plants.

Science.gov (United States)

Agathokleous, Evgenios; Kitao, Mitsutoshi; Calabrese, Edward J

2018-07-01

Lanthanum is a rare earth element (REE) which has been extensively studied due to its wide application in numerous fields with a potential accumulation in the environment. It has long been known for its potential to stimulate plant growth within a hormetic-biphasic dose response framework. This article provides evidence from a series of high resolution studies published within the last two decades demonstrating a substantial and significant occurrence of lanthanum-induced hormesis in plants. These findings suggest that hormetic responses should be built into the study design of hazard assessment study protocols and included in the risk assessment process. Hormesis also offers the opportunity to substantially improve cost benefit estimates for environmental contaminants, which have the potential to induce beneficial/desirable effects at low doses. Copyright © 2018 Elsevier Ltd. All rights reserved.

Responses in sediment phosphorus and lanthanum concentrations and composition across 10 lakes following applications of lanthanum modified bentonite

DEFF Research Database (Denmark)

Dithmer, Line; Nielsen, Ulla Gro; Lürling, Miquel

2016-01-01

and binding forms, P adsorption capacity of discrete sediment layers, and pore water P concentrations. Lanthanum phosphate mineral phases were confirmed by solid state (31)P MAS NMR and LIII EXAFS spectroscopy. Rhabdophane (LaPO4 · nH2O) was the major phase although indications of monazite (LaPO4) formation...... conditions of P retention (with the exception of two lakes) by sediments, indicating effective control of sediment P release, i.e. between two and nine years after treatment....

Yttrium and lanthanum recovery from low cerium carbonate, yttrium carbonate and yttrium concentrate

International Nuclear Information System (INIS)

Vasconcelos, Mari Estela de

2006-01-01

In this work, separation, enrichment and purification of lanthanum and yttrium were performed using as raw material a commercial low cerium rare earth concentrate named LCC (low cerium carbonate), an yttrium concentrate named 'yttrium carbonate', and a third concentrated known as 'yttrium earths oxide. The first two were industrially produced by the late NUCLEMON - NUCLEBRAS de Monazita e Associados Ltda, using Brazilian monazite. The 'yttrium earths oxide' come from a process for preparation of lanthanum during the course of the experimental work for the present thesis. The following techniques were used: fractional precipitation with urea; fractional leaching of the LCC using ammonium carbonate; precipitation of rare earth peroxycarbonates starting from the rare earth complex carbonates. Once prepared the enriched rare earth fractions the same were refined using the ion exchange chromatography with strong cationic resin without the use of retention ion and elution using the ammonium salt of ethylenediaminetetraacetic acid. With the association of the above mentioned techniques were obtained pure oxides of yttrium (>97,7%), lanthanum (99,9%), gadolinium (96,6%) and samarium (99,9%). The process here developed has technical and economic viability for the installation of a large scale unity. (author)

Electrical behaviour of strontium-doped lanthanum manganite interfaces

DEFF Research Database (Denmark)

Koch, Søren; Hendriksen, P.V.; Jacobsen, Torben

2005-01-01

The contact resistance of strontium-doped lanthanum manganite (LSM) contact pairs is investigated by polarisation analysis at different temperatures and atmospheres. The ceramic contacts have a high contact resistance, and strongly nonlinear current–voltage behaviour is observed at low temperatur....... The nonlinear behaviour is ascribed to the presence of energy barriers at the contact interface. Generally, point contacts showed a more linear behaviour than plane contact interfaces....

Selective isotope determination of lanthanum by diode-laser-initiated resonance-ionization mass spectrometry

International Nuclear Information System (INIS)

Young, J.P.; Shaw, R.W.

1995-01-01

A diode-laser step has been incorporated into a resonance-ionization mass spectrometry optical excitation process to enhance the isotopic selectivity of the technique. Lanthanum isotope ratio enhancements as high as 10 3 were achieved by use of a single-frequency cw diode laser tuned to excite the first step of a three-step excitation--ionization optical process; the subsequent steps were excited by use of a pulsed dye laser. Applying the same optical technique, we measured atomic hyperfine constants for the high-lying even-parity 4 D 5/2 state of lanthanum at 30 354 cm --1 . The general utility of this spectral approach is discussed

Oriented growing and anisotropy of emission properties of lanthanum hexaboride single crystals

International Nuclear Information System (INIS)

Lazorenko, V.I.; Lotsko, D.V.; Platonov, V.F.; Kovalev, A.V.; Galasun, A.P.; Matvienko, A.A.; Klinkov, A.E.

1987-01-01

Single crystals of lanthanum hexaboride with preset crystallographic orientation are grown by the method of crucible-free zone melting. It is shown that oriented growing of single crystals of the given compound is possible only when using seed crystals of the required orientation because no predominant orientation of the LaB 6 growth is found in case of spontaneous crystallization. Orientation of spontaneously growing LaB 6 crystals does not depend on their growth rate, degree of the melt diffusion annealing, purity of the inital powder. Anisotropy of the electronic work function for single crystal lanthanum hexaboride is confirmed. Its value grows as (100)<(110)<(111). Conditions of the preliminary thermovacuum purification of the surface are shown to affect the measured work function

Thermoelectric power and electrical conductivity of strontium-doped lanthanum manganite

DEFF Research Database (Denmark)

Ahlgren, E.O.; Poulsen, F.W.

1996-01-01

Thermoelectric power and electrical conductivity of pure and 5, 10 and 20% strontium-doped lanthanum manganite are determined as function of temperature in air and of P-O2 at 1000 degrees C. At high temperatures the thermoelectric power is negative. Both thermoelectric power and conductivity...

A case of lanthanum carbonate ingestion thought to be phlebosclerotic colitis on CT imaging and abdominal radiograph

International Nuclear Information System (INIS)

Harris, K.; Balcam, S.

2017-01-01

A male admitted in the early hours of the morning, complained of a four week, right sided, non-radiating, dull and intermittent abdominal pain. Imaging suggested a diagnosis of phlebosclerotic colitis which was later discounted when the patients' history of lanthanum carbonate ingestion was examined. Phlebosclerotic colitis mostly affects the Asian population, and its cause is still not known, but can be associated with specific radiographic features. Collections of lanthanum may confuse a diagnosis of phlebosclerotic colitis as well as other factors such as voxel errors, photon starvation and movement. - Highlights: • PC can be non-specific, its cause unknown, diagnosis is often delayed. • PC depends on specific radiographic features. • Lanthanum Carbonate can collect within the lumen and confuses diagnosis. • Voxel errors, photon starvation and patient movement can displace densities.

On magnetic ordering in heavily sodium substituted hole doped lanthanum manganites

Energy Technology Data Exchange (ETDEWEB)

Sethulakshmi, N. [Department of Physics, Cochin University of Science and Technology, Cochin 682022, Kerala (India); Unnimaya, A.N. [Centre for Materials for Electronic Technology (CMET), Thrissur 680581, Kerala (India); Al-Omari, I.A.; Al-Harthi, Salim [Department of Physics, Sultan Qaboos University, PC 123 Muscat (Oman); Sagar, S. [Government College for Women, Thiruvananthapuram 695014, Kerala (India); Thomas, Senoy [Materials Science and Technology Division, National Institute for Interdisciplinary Science and Technology, Thiruvananthapuram 695019, Kerala (India); Srinivasan, G. [Department of Physics, Oakland University, Rochester (United States); Anantharaman, M.R., E-mail: mraiyer@yahoo.com [Department of Physics, Cochin University of Science and Technology, Cochin 682022, Kerala (India)

2015-10-01

Mixed valence manganite system with monovalent sodium substituted lanthanum manganites form the basis of the present work. Lanthanum manganites belonging to the series La{sub 1−x}Na{sub x}MnO{sub 3} with x=0.5–0.9 were synthesized using modified citrate gel method. Variation of lattice parameters and unit cell volume with Na concentration were analyzed and the magnetization measurements indicated ferromagnetic ordering in all samples at room temperature. Low temperature magnetization behavior indicated that all samples exhibit antiferromagnetism along with ferromagnetism and it has also been observed that antiferromagnetic ordering dominates ferromagnetic ordering as concentration is increased. Evidence for such a magnetic inhomogeneity in these samples has been confirmed from the variation in Mn{sup 3+}/Mn{sup 4+} ion ratio from X-ray Photoelectron Spectroscopy and from the absorption peak studies using Ferromagnetic Resonance Spectroscopy. - Highlights: • Higher substitution of more than 50 percent of monovalent ion, sodium for La sites in lanthanum manganites scarce in literature. • Structural studies using XRD and further structure refinement by Rietveld refinement confirmed orthorhombic pbnm spacegroup. • Ferromagnetic behavior at room temperature with saturation magnetization decreasing with increase in sodium concentration. • M vs T measurements using FC ZFC proved coexisting FM/AFM behavior arising from exchange interactions between different valence states of Mn ions. • Disparity in ratio of Mn valence ions indicated presence of vacancies providing the role of vacancies and oxygen stoichiometry in deciding magnetic inhomogeneity.

Self-assembly in lanthanum(III) and calcium(II) complexes of salicylaldimines derived from putrescine

International Nuclear Information System (INIS)

Pospieszna-Markiewicz, Izabela; Kaczmarek, Malgorzata T.; Kubicki, Maciej; Radecka-Paryzek, Wanda

2008-01-01

The one-step template reaction of salicylaldehyde with putrescine, a biogenic diamine, in the presence of lanthanum(III) or calcium(II) ions produces salicylaldimine complexes containing the N,N'-bis(salicylidene)-1,4-butanediamine ligand L as a result of the [2 + 1] Schiff base condensation. The X-ray diffraction studies of the lanthanum complex reveals an infinite [La 2 L 4 (NO 3 ) 6 ] ∞ polymeric structure based on networks of 10-coordinated La(III) nodes linked by bridging unionized ligands that use exclusively the oxygens as donor atoms with the nitrogen atoms not being involved in coordination

Application of the Rietveld method in powders of strontium-doped lanthanum manganite calcined in different temperatures

International Nuclear Information System (INIS)

Chiba, R.; Vargas, R.A.; Martinez, L.G.; Andreoli, M.; Seo, E.S.M.

2010-01-01

The strontium-doped lanthanum manganite (LSM) is a ceramic material used as cathode in device called High Temperature Solid Oxide Fuel Cell. In this work, the LSM was synthesized by the citrate technique with the objective to get powders without the formation of secondary phases, such as lanthanum oxide and the lanthanum hydroxide, harmful for the functional performance of the device. The definitive calcination temperatures had been 700, 900 and 1100 deg C, due the decomposition of the polymeric precursors to present stabilization from 480 deg C. The analysis by X-ray diffraction of the calcined powders in different temperatures shows the formation only of phase LSM of hexagonal crystalline structure, type pseudo-perovskite. Using the refinement of Rietveld was determined the parameters and volumes of unity cells, atomic positions and occupations. These results confirm that the chemical compositions obtained are similar to the nominal. (author)

Selective transport and incorporation of highly charged metal and metal complex ions in self-assembled polyelectrolyte multilayer membranes

International Nuclear Information System (INIS)

Toutianoush, Ali; Tieke, Bernd

2002-01-01

The transport of aqueous salts containing mono-, di- and trivalent metal and tetravalent metal complex ions across ultrathin polyvinylammonium/polyvinylsulphate (PVA/PVS) membranes is described. The membranes were prepared by electrostatic layer-by-layer (LBL) assembly of the two polyelectrolytes. Using spectroscopic measurements and permeability studies, it is demonstrated that the transport of copper(II) chloride, lanthanum(III) chloride, barium chloride and potassium hexacyanoferrate(II) is accompanied by the permanent incorporation of the metal and metal complex ions in the membrane. Upon the uptake of copper, lanthanum and hexacyanoferrate ions, the membranes become cross-linked so that the permeation rates of other salts not taken up by the membrane, e.g. sodium chloride, potassium chloride and magnesium chloride, are decreased. The uptake of barium ions leads to a decrease of the cross-linking density of the membrane so that the permeation rate of NaCl is increased. Possible mechanisms for the ion uptake are discussed

Impact of Annealing Temperature on the Physical Properties of the Lanthanum Deficiency Manganites

Directory of Open Access Journals (Sweden)

Skini Ridha

2017-10-01

Full Text Available The lanthanum deficiency manganites La0.8-x□xCa0.2MnO3 (x = 0, 0.1 and 0.2, where □ is a lanthanum vacancy, were prepared using the classic ceramic methods with different thermal treatments (1373 K and 973 K. The structural, magnetic, and magnetocaloric properties of these compounds were studied as a function of annealing temperature. It was noted that the annealing temperature did not affect the crystal structure of our samples (orthorhombic structure with Pnma space group. Nevertheless, a change in the variation of the unit cell volume V, the average bond length dMn–O, and the average bond angles θMn–O–Mn were observed. Magnetization versus temperature study has shown that all samples exhibited a magnetic transition from ferromagnetic (FM to paramagnetic (PM phase with increasing temperature. However, it can be clearly seen that the annealing at 973 K induced an increase of the magnetization. In addition, the magnetocaloric effect (MCE as well as the relative cooling power (RCP were estimated. As an important result, the values of MCE and RCP in our Lanthanum-deficiency manganites are reported to be near to those found in gadolinium, considered as magnetocaloric reference material.

Modification of TiO2 nanoparticles through lanthanum doping and PEG templating

Directory of Open Access Journals (Sweden)

Marija Milanovic

2014-12-01

Full Text Available Pure and lanthanum doped titania nanopowders were synthesized through a room temperature sol-gel method using a template of polyethylene glycol (PEG. The progress of the synthesis in terms of phase formation and size of nanoparticles was monitored by X-ray diffraction, FTIR spectroscopy and SEM analysis. After calcination at 450 °C in air, the results have shown the presence of small particles crystallized predominantly in the form of anatase phase, with significant agglomeration. Nitrogen adsorption-desorption measurements confirmed that all prepared powders are mesoporous with an average pore diameter in range 3.1–3.8 nm. The addition of lanthanum ions leads to the nanopowders with the highest specific surface (BET area (203 m2/g. The obtained powders were compared to TiO2 prepared without a template.

Lanthanum and yttrium oxysulfides activated by europium: (Ln1-x Eux)2 O2 S - Synthesis and characterization

International Nuclear Information System (INIS)

Luiz, J.M.

1989-01-01

The synthesis of lanthanum and yttrium oxysulfides activated by europium were obtained by thermal decomposition of lanthanum and yttrium oxalates doped with europium, under an argon and sulphur atmosphere. The thermal decomposition of these compounds is studied by differential thermal analysis (DTA). The characterization of these oxysulfides were made by chemical analyses, infrared spectroscopy, X-ray diffraction, scanning electron microscopy and emission spectroscopy. (M.V.M.)

Molecular absorption spectra of beryllium, cerium, lanthanum, iron, and platinum salts

International Nuclear Information System (INIS)

Daidoji, Hidehiro

1980-01-01

The absorption spectra of some salts of beryllium, cerium, lanthanum, iron and platinum in air-acetylene flame were measured in the wavelength range from 200 to 400 nm. A Hitachi 207 type atomic absorption spectrophotometer was used. A deuterium lamp, a home-made continuous radiation lamp and some hollow cathode lamps were used as light sources. The new molecular absorption spectra of cerium, lanthanum and platinum and the absorption spectra due to Be(OH) 2 , LaO, PtH, FeO and FeCl in 200-400 nm region were obtained. Emission spectra of CeO, LaO and FeOH were also obtained. These molecular absorption bands were estimated as absorption errors of maximum 15 times to the sensitivity of each elements in atomic absorption spectrometry. In addition, spectral line interferences of iron were observed in atomic absorption spectrometry of Zn, Cd, Ni, Cu and Cr. (author)

Effects of adding lanthanum to Ni/ZrO2 catalysts on ethanol steam reforming

International Nuclear Information System (INIS)

Profeti, Luciene Paula Roberto; Habitzheuter, Filipe; Assaf, Elisabete Moreira

2012-01-01

The catalytic performance of Ni/ZrO 2 catalysts loaded with different lanthanum content for steam reforming of ethanol was investigated. Catalysts were characterized by BET surface area, X-ray diffraction, UV-vis spectroscopy, temperature programmed reduction, and X-ray absorption fine structure techniques. Results showed that lanthanum addition led to an increase in the degree of reduction of both NiO and nickel surface species interacting with the support, due to the higher dispersion effect. The best catalytic performance at 450 deg C was found for the Ni/12LZ catalyst, which exhibited an effluent gaseous mixture with the highest H 2 yield. (author)

Growth and physico chemical characterization of lanthanum neodymium oxalate single crystals

International Nuclear Information System (INIS)

Raju, K.S.; John, Varughese; Ittyachen, M.A.

1998-01-01

Single crystals of lanthanum neodymium oxalate (LNO) are grown in sodium meta silicate gels, by the diffusion of a mixture of aqueous solutions of lanthanum nitrate and neodymium nitrate into the test tube having the set gel containing oxalic acid. The bluish pink coloured tabular crystals of LNO having well defined hexagonal basal planes appear either as foggy or clear, the latter at the greater depths inside the gel. The coloration of LNO visually observed is evidenced in UV-visible spectrum, by the revelation of well pronounced characteristic peaks in the visible region (500-900 nm). X-ray diffraction (XRD) of powdered LNO is ordered, meaning crystalline in nature, besides its isostructurality with similarly grown lanthanum samarium oxalate crystals. The single crystallinity of LNO is established by its oscillation XRD pattern. Thermogravimetric analysis (TGA) and differential scanning colorimetry (DSC) support that LNO loses water of crystallization around 120 degC and CO and CO 2 around 350-450 degC, while the infrared absorption (IR) spectrum of LNO establishes the presence of oxalate (C 2 O 4 ) 2- ions. Energy dispersive x-ray analysis (EDAX) confirms the presence of La and Nd in the sample. X-ray photoelectron spectroscopic (XPS) studies of LNO establish the presence of La and Nd in their respective oxide states. An empirical structure for LNO has been proposed on the basis of these findings. The smokiness in the foggy LNO crystal has been attributed due to the gel inclusion during the growth process. (author)

Synthesis and Characterization of Lanthanum Complexes with Amino Acid Schiff Base

Institute of Scientific and Technical Information of China (English)

张秀英; 张有娟; 杨林

2001-01-01

Six new complexes of lanthanum with amino acid Schiff base ligands, A-F, were prepared in methanol-aqueous solution. The composition and properties of the title complexes were characterized by elemental analysis, molar conductance, infrared, electronic spectra, 1H NMR, thermogravimetric and differential thermal analysis.

Separation of lanthanum from samarium on solid aluminum electrode in LiCl-KCl eutectic melts

International Nuclear Information System (INIS)

De-Bin Ji; Mi-Lin Zhang; Xing Li; Xiao-Yan Jing; Wei Han; Yong-De Yan; Yun Xue; Zhi-Jian Zhang; Harbin Engineering University, Harbin

2015-01-01

This paper presents an electrochemical study on the separation of lanthanum from samarium on aluminum electrode at 773 K. The results from different electrochemical methods showed that Sm(III) and La(III) formed Al-Sm and Al-La intermetallic compounds on an aluminum electrode at electrode potential around -1.67 and -1.46 V, respectively. The electrochemical separation of lanthanum was carried out in LiCl-KCl-LaCl 3 -SmCl 3 melts on solid aluminum electrodes at 773 K by potentiostatic electrolysis at -1.45 V for 40 h and the separation efficiency was 99.1 %. (author)

Effect of lanthanum substitution on dielectric relaxation, impedance response, conducting and magnetic properties of strontium hexaferrite

Energy Technology Data Exchange (ETDEWEB)

Want, Basharat, E-mail: bawant@kashmiruniversity.ac.in; Bhat, Bilal Hamid; Ahmad, Bhat Zahoor

2015-04-05

Highlights: • The substitution of La affects the dielectric and magnetic properties of strontium hexaferrite. • The electric behaviour of the compound follows the Koop’s phenomenological theory. • The impedance study shows the role of grain boundaries to the electric properties of the compound. • The substitution of La to strontium hexaferrite reduces the resistive nature of grain boundaries. - Abstract: Lanthanum strontium hexaferrite Sr{sub 1−x}La{sub x}Fe{sub 12}O{sub 19} (x = 0, 0.08, 0.13 , 0.18) has been successfully synthesized by using citrate-precursor method and characterized by different techniques. The X-ray diffraction results revealed that the sample is crystalline in nature and is of single phase with the space group P63/mmc. The dielectric, conducting and impedance related studies have been carried out as a function of frequency and concentration of lanthanum in the frequency ranges of 20 Hz–3 MHz. Impedance studies were performed in the frequency domain to distinguish between bulk and grain boundary contributions of the material to the overall dielectric response. The electric response of the material was also modeled by an equivalent circuit and different circuit parameters were calculated. Magnetic characterization of the material was also performed and the effect of lanthanum concentration was studied. The hysteresis loop obtained from the magnetometer showed that with the increase of lanthanum concentration, the saturation magnetisation decreases while as coercivity increases.

Studies on the lanthanum arsenate ion-exchanger: preparation, physicochemical properties and applications

International Nuclear Information System (INIS)

Mukherjee, A.K.; Mandal, S.K.

1984-01-01

The cation-exchange behaviour of lanthanum arsenate has been studied. This paper reports the preparation and physicochemical properties of the exchanger. Its analytical utility is compared with that of other arsenate exchangers. Some practical analytical applications are described. (author)

46 CFR 151.50-34 - Vinyl chloride (vinyl chloride monomer).

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Vinyl chloride (vinyl chloride monomer). 151.50-34... chloride (vinyl chloride monomer). (a) Copper, aluminum, magnesium, mercury, silver, and their alloys shall... equipment that may come in contact with vinyl chloride liquid or vapor. (b) Valves, flanges, and pipe...

Polyvinyl chloride resin

International Nuclear Information System (INIS)

Kim, Hong Jae

1976-06-01

This book contains polyvinyl chloride resin industry with present condition such as plastic industry and polyvinyl chloride in the world and Japan, manufacture of polyvinyl chloride resin ; suspension polymerization and solution polymerization, extruding, injection process, hollow molding vinyl record, vacuum forming, polymer powders process, vinyl chloride varnish, vinyl chloride latex, safety and construction on vinyl chloride. Each chapter has descriptions on of process and kinds of polyvinyl chloride resin.

Development of a 1 kW Class SOFC Stack using Doped Lanthanum Gallate

Energy Technology Data Exchange (ETDEWEB)

Akikusa, J.; Adachi, K.; Yamada, T.; Akbay, T.; Murakami, N.; Chitose, N.; Hoshino, K.; Hosoi, K.; Yoshida, H.; Sasaki, T.; Inagaki, T.; Ishihara, T.; Takita, Y.

2002-06-01

The performance of lanthanum gallate based SOFC has been investigated as a high-energy conversion device. A planar type SOFC which could operate at temperatures below 800 {sup o}C has been jointly developed. As an electrolyte material, lanthanum gallate (LaGaO{sub 3}) with substitutions of Sr for the La site and Mg and Co for the Ga site (LSGMC) was used. The synthesis technique for large-sized cell production has been established, and the performance of a self- supported diameter 154 mm cell with 200 {mu}m electrolyte thickness is investigated. The output power of 50 W has been obtained with a conversion efficiency [LHV] of 45 % for a single cell. In addition, a metallic separator made of stainless steel was chosen and tested successfully for a seal-less stack. The output power of 1 kW by means of the stack of 18 cells has been achieved for the first time utilizing lanthanum gallate. Moreover, NiO-SDC composite powders were prepared by the spray pyrolysis method and used for the anode on 100 {mu}m thickness LSGMC electrolyte with a combination of samarium cobaltite for the cathode. The power density of as high as 1.8 W/cm{sup 2} at 0.7 V terminal voltage was achieved at 800{sup o}C. (author)

Materials system for intermediate temperature solid oxide fuel cells based on doped lanthanum-gallate electrolyte

Science.gov (United States)

Gong, Wenquan

2005-07-01

The objective of this work was to identify a materials system for intermediate temperature solid oxide fuel cells (IT-SOFCs). Towards this goal, alternating current complex impedance spectroscopy was employed as a tool to study electrode polarization effects in symmetrical cells employing strontium and magnesium doped lanthanum gallate (LSGM) electrolyte. Several cathode materials were investigated including strontium doped lanthanum manganite (LSM), Strontium and iron doped lanthanum cobaltate (LSCF), LSM-LSGM, and LSCF-LSGM composites. Investigated Anode materials included nickel-gadolinium or lanthanum doped cerium oxide (Ni-GDC, or Ni-LDC) composites. The ohmic and the polarization resistances of the symmetrical cells were obtained as a function of temperature, time, thickness, and the composition of the electrodes. Based on these studies, the single phase LSM electrode had the highest polarization resistance among the cathode materials. The mixed-conducting LSCF electrode had polarization resistance orders of magnitude lower than that of the LSM-LSGM composite electrodes. Although incorporating LSGM in the LSCF electrode did not reduce the cell polarization resistance significantly, it could reduce the thermal expansion coefficient mismatch between the LSCF electrodes and LSGM electrolyte. Moreover, the polarization resistance of the LSCF electrode decreased asymptotically as the electrode thickness was increased thus suggesting that the electrode thickness needed not be thicker than this asymptotic limit. On the anode side of the IT-SOFC, Ni reacted with LSGM electrolyte, and lanthanum diffusion occurred from the LSGM electrolyte to the GDC barrier layer, which was between the LSGM electrolyte and the Ni-composite anode. However, LDC served as an effective barrier layer. Ni-LDC (70 v% Ni) anode had the largest polarization resistance, while all other anode materials, i.e. Ni-LDC (50 v% Ni), Ni-GDC (70 v% NO, and Ni-GDC (50 v% Ni), had similar polarization

Nanostructured Lanthanum Halides and CeBr3 for Nuclear Radiation and Detection

International Nuclear Information System (INIS)

Guss, Paul; Mukhopadhyay, Sanjoy; Guise, Ron; Yuan, Ding

2010-01-01

Scintillator materials are used to detect, and in some cases identify, gamma rays. Higher performance scintillators are expensive, hard to manufacture, fragile, and sometimes require liquid nitrogen or cooling engines. But whereas lower-quality scintillators are cheap, easy to manufacture, and more rugged, their performance is lower. At issue: can the desirable qualities of high-and low-performance scintillators be combined to achieve better performance at lower cost? Preliminary experiments show that a LaF 3 :Ce oleic acid-based nanocomposite exhibits a photopeak when exposed to 137 Cs source gamma-radiation. The chemical synthesis of the cerium-doped lanthanum halide nanoparticles are scalable and large quantities of material can be produced at a time, unlike typical crystal growth processes such as the Bridgeman process. Using a polymer composite (Figure 1), produced by LANL, initial measurements of the unloaded and 8% LaF 3 :Ce-loaded sample have been made using 137 Cs sources. Figure 2 shows an energy spectrum acquired for CeF 3 . The lighter plot is the measured polymer-only spectrum and the black plot is the spectrum from the nanocomposite scintillator. As the development of this material continues, the energy resolution is expected to improve and the photopeak-to-Compton ratio will become greater at higher loadings. These measurements show the expected Compton edge in the polymer-only sample, and the Compton edge and photo-peak expected in the nanophosphor composites that LANL has produced. Using a porous VYCORR with CdSe/ZnS core shell quantum dots, Letant has demonstrated that he has obtained signatures of the 241Am photopeak with energy resolution as good at NaI (Figure 3). We begin with the fact that CeBr 3 crystals do not have a self-activity component as strong as the lanthanum halides. The radioactive 0.090% 138 La component of lanthanum leads to significant self-activity, which will be a problem for very large detector volumes. Yet a significant

Lanthanum (samarium) nitrate-4-aminoantipyrine nitrate-water systems

International Nuclear Information System (INIS)

Starikova, L.I.; Zhuravlev, E.F.

1985-01-01

Using the isothermal method of cross-sections at 50 deg C systems lanthanum nitrate-4-aminoantipyrine nitrate-water (1), samarium nitrate-4-aminoantipyrine nitrate-water (2), are studied. Isotherms of system 1 consist of two crystallization branches of initial salt components. In system 2 formation of congruently soluble compounds of the composition Sm(No) 3 ) 3 xC 11 H 13 ON 3 xHNO 3 is established. Analytical, X-ray phase and thermogravimetric analysis of the isolated binary salt are carried out

Apparent molar volumes and compressibilities of lanthanum, gadolinium and lutetium trifluoromethanesulfonates in dimethylsulfoxide

International Nuclear Information System (INIS)

Warmińska, Dorota; Wawer, Jarosław

2012-01-01

Highlights: ► Sequence of volumes and compressibilities of Ln 3+ ions in DMSO is: La 3+ > Gd 3+ 3+ . ► Sequence of the partial molar volumes do not change with temperature. ► These results are the consequence of nature of the ion–solvent bonding. - Abstract: Temperature dependencies of the densities of dimethylsulfoxide solutions of lanthanum, gadolinium and lutetium trifluoromethanesulfonates have been determined over a wide range of concentrations. The apparent molar volumes and partial molar volumes of the salts at infinite dilution, as well as the expansibilities of the salts, have been calculated from density data. Additionally, the apparent molar isentropic compressibilities of lanthanum, gadolinium and lutetium trifluoromethanesulfonates have been calculated from sound velocity data at 298.15 K. The data obtained have been interpreted in terms of ion−solvent interactions.

Influence of Lanthanum Doping on the Structural and Optical Properties of Hematite Nanopowders

Science.gov (United States)

Justus, J. Sharmila; Dharma Roy, S. Dawn; Raj, A. Moses Ezhil

2016-10-01

Rare-earth elements are an attractive class of dopant elements, as they give easily trivalent cations that possibly altering the structure and other properties of the parent nanoparticles and creating multifunctional materials because of their f-electronic configurations. Herein, experimental evidence has been given for a better understanding of the factors that dictate the interactions of La doping on the structure and optical properties of iron oxide nanoparticles. For that, lanthanum doped hematite (α-Fe2O3) nanoparticles were prepared by a facile solution method using iron (III) chloride (FeCl3) as starting precursor and sodium hydroxide (NaOH) as reducing agent without templates at low temperature. As-prepared powders were subsequently calcined in air for 3 hr at 800 °C. Xray diffraction (XRD) technique was used to study the nanocrystal formation of α-Fe2O3 and Fourier Transform Raman (FT-Raman) spectral information identified the chemical bond structure of the nanoparticles. Morphology study of the nanoparticles was identified using Scanning Electron Microscope (SEM) and the incorporated La content was recognized from the Energy Dispersive X-ray Spectroscopy (EDS) analysis. The optical absorption spectrum was recorded in the wavelength range of 200-2000 nm and the optical parameters such as absorption coefficient and optical band gap energy of pure and doped Fe2O3 nanoparticles were determined. Obtained results are interpreted by considering the impregnation of trivalent La cations that replaced Fe cations of the host structure.

Effect of various lanthanum sol-gel coatings on the 330Cb (Fe-35Ni-18Cr-1Nb-2Si) oxidation at 900 deg. C

Energy Technology Data Exchange (ETDEWEB)

Buscail, H., E-mail: buscail@iut.u-clermont1.fr [Clermont Universite- LVEEM, 8 rue J.B. Fabre, BP 219, 43006 Le Puy en Velay (France); Issartel, C.; Riffard, F.; Rolland, R.; Perrier, S. [Clermont Universite- LVEEM, 8 rue J.B. Fabre, BP 219, 43006 Le Puy en Velay (France); Fleurentin, A. [CETIM, 52 av Felix Louat, BP 80067, 60304 Senlis (France); Josse, C. [L' ICB UMR5209 CNRS, BP 47870, 21078 Dijon (France)

2011-11-01

The influence of a lanthanum sol-gel coating on the oxide scale adherence has been studied during the 330Cb (Fe-35Ni-18Cr-1Nb-2Si) oxidation at 900 deg. C, in air. The alloy oxidation is performed in order to generate a protective chromia scale acting as a good barrier against carburization. Argon annealing of lanthanum sol-gel coatings have been performed at various temperatures in order to find the best conditions to insure the scale adherence. Kinetic results show that lanthanum sol-gel coatings lead to a lower oxidation rate compared to blank specimens. Thermal cycling tests on lanthanum the sol-gel coated specimen show that the oxide scale formed at 900 deg. C, in air, is adherent.

Hydrocarbon conversion with cracking catalyst having co-combustion promoters lanthanum and iron

International Nuclear Information System (INIS)

Csicsery, S.M.

1979-01-01

A composition useful in hydrocarbon conversion processes such as catalytic cracking comprises 0.05 to 10 weight percent lanthanum associated with a refractory support. The composition may also include 0.02 to 10 weight percent iron. The refractory support is a zeolitic crystalline aluminosilicate

Paramagnetic resonance of Mn4+ and Mn2+ centers in lanthanum gallate single crystals

Science.gov (United States)

Vazhenin, V. A.; Potapov, A. P.; Guseva, V. B.; Artyomov, M. Yu.

2010-03-01

An increase in the manganese concentration in lanthanum gallate in the range 0.5-5.0% has been found to result in a complete replacement of individual Mn4+ ions by Mn2+ ions. The relative concentrations and binding energies of individual Mn4+, Mn3+, and Mn2+ ions have been determined. The spin Hamiltonians of the Mn2+ and Mn4+ centers in the rhombohedral and orthorhombic phases, respectively, have been constructed and the orientation of the principal axes of the fine-structure tensor of Mn4+ at room temperature has been found. The possibility of using electron paramagnetic resonance for determining the rotation angles of oxygen octahedra of lanthanum gallate with respect to the perovskite structure has been discussed.

Adsorbtion of oxygen and cesium on lanthanum hexaboride

International Nuclear Information System (INIS)

Gorodetskij, D.A.; Tskhakaya, V.K.; Shchudlo, Yu.G.; Yarygin, V.I.; Yas'ko, A.A.

1982-01-01

Oxygen and cesium adsorption on lanthanum hexaboride was investigated. Especial attention was paid to structural investigations of the LaB 6 (100)-O system. Diffraction pictures and curves of changes in work function in the process of oxygen disorption have been obtained. At oxygen adsorption on a crystal heated up to different temperatures in the range of 900-1400 K the same diffraction pictures as at corresponding annealing temperatures observed were. It is noted that adsorption heat changes slightly in the LaB 6 -O-Cs system

Inner-sphere and outer-sphere complexes of yttrium(III), lanthanum (III), neodymium(III), terbium(III) and thulium(III) with halide ions in N,N-dimethylformamide

International Nuclear Information System (INIS)

Takahashi, Ryouta; Ishiguro, Shin-ichi

1991-01-01

The formation of chloro, bromo and iodo complexes of yttrium(III), and bromo and iodo complexes of lanthanum(III), neodymium(III), terbium(III) and thulium(III) has been studied by precise titration calorimetry in N,N-dimethylformamide (DMF) at 25 o C. The formation of [YCl] 2+ , [YCl 2 ] + , [YCl 3 ] and [YCl 4 ] - , and [MBr] 2+ and [MBr 2 ] + (M = Y, La, Nd, Tb, Tm) was revealed, and their formation constants, enthalpies and entropies were determined. It is found that the formation enthalpies change in the sequence ΔH o (Cl) > ΔH o (l), which is unusual for hard metal (III) ions. This implies that, unlike the chloride ion, the bromide ion forms outer-sphere complexes with the lanthanide(III) and yttrium(III) ions in DMF. Evidence for either an inner- or outer-sphere complex was obtained from 89 Y NMR spectra for Y(ClO 4 ) 3 , YCl 3 and YBr 3 DMF solutions at room temperature. (author)

Synthesis and characterization of nanoporous strontium-doped lanthanum cobaltite thin film using metal organic chemical solution deposition

Energy Technology Data Exchange (ETDEWEB)

Park, Jun-Sik [Department of Mechanical Convergence Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Kim, Young-Beom, E-mail: ybkim@hanyang.ac.kr [Department of Mechanical Convergence Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Institute of Nano Science and Technology, Hanyang University, Seoul 133-791 (Korea, Republic of)

2016-01-29

By employing strontium as a dopant of lanthanum cobaltite (LaCoO{sub 3}), strontium-doped lanthanum cobaltite (La{sub 1−x}Sr{sub x}CoO{sub 3−δ}, LSC) thin film was fabricated using a metal organic chemical solution deposition (MOCSD) method. Lanthanum nitrate hexahydrate [La(NO{sub 3}){sub 3}6H{sub 2}O], strontium acetate [Sr(CH{sub 3}COO){sub 2}], and cobalt acetate tetrahydrate [Co(CH{sub 3}COO){sub 2}4H{sub 2}O] were used as precursors. The coating process was performed through a spin coating method on a substrate, which were then heat treated under various temperature conditions. Electrical properties, microstructures, and crystalline structures with respect to sintering temperature were analyzed. According to these analyses, the change in surface morphology, phase shift, and conductive properties were closely related, which could explain their respective behaviors. Furthermore, sintered strontium-doped lanthanum perovskite oxides showed various conductivities according to the amount of dopant. With the molar ratio of strontium that is stoichiometrically equivalent to lanthanum (La{sub 0.5}Sr{sub 0.5}CoO{sub 3−δ}) thin film showed the best conductivity in the sintering temperature range of 650–700 °C, with perovskite phases formed at this temperature condition. As the electrically conductive properties of the thin film are a function of thickness, the films were coated several times to a thickness of approximately 300 nm, with the lowest resistivity (approximately 9.06 × 10{sup −4} Ω cm) observed at the optimized sintering temperature and solution composition. - Highlights: • LSC thin film was fabricated by metal organic chemical solution deposition (MOCSD). • The film shows good agreement on the electrical conductivity of LSC by conventional methods. • The properties of LSC film are influenced by the surface morphology and crystalline phase. • Optimal molar ratio of strontium for the highest conductivity was investigated.

Determination of the constants of the solubility product of Ln(OH)3 and the effect of the chloride ions on the lanthanum hydrolysis, praseodymium and lutetium in aqueous solutions of ion force 2 Molar

International Nuclear Information System (INIS)

Lopez G, H.D.

2005-01-01

The behavior of lanthanum (III), praseodymium (III), and lutetium (III) was studied in 2 M NaClO 4 (aq) and 2 M NaCl (aq) at 303 K and free -CO 2 conditions. Solubility diagrams (p Ln(aq)-pC H ) were obtained by means of a radiochemical method. The pC H borderlines of saturation and unsaturation zones of the solutions and solubility product constants for Ln(OH) 3 were determined from these diagrams. The fitting of the solubility equation to the experimental values of p Ln(aq)-pC H diagrams allowed the calculation of the first hydrolysis and solubility product constants. Independently, the stability constants for the first species of hydrolysis were determined by means of pH titrations, the data were treated with the program SUPERQUAD and fitted to the mean ligand number equation. The stability constants for the species LnCl 2+ were as well calculated in 2M ionic strength and 303 K from the hydrolysis constant values obtained in both perchlorate and chloride media. The values obtained for La, Pr and Lu were: logK ps : 21.11 ± 0.09, 19.81 ± 0.11 and 18.10 ± 0.13 in 2M NaClO 4 ; logK ps : 22.22 ± 0.09, 21.45 ± 0.14 and 18.52 ± 0.29 in 2M NaCl; log β 1 : - 8.64 ± 0.02, - 8.37 ± 0.01 and - 7.95 ± 0.11 in 2M NaClO 4 ; log β 1 / : - 9.02 ± 0.11, - 8.75 ± 0.01 and - 8.12 ± 0.03 in 2M NaCl and the values for log β 1,Cl were - 0.0255, - 0.155 and - 0.758, respectively. (Author)

Lanthanum carbonate versus placebo for management of hyperphosphatemia in patients undergoing peritoneal dialysis: a subgroup analysis of a phase 2 randomized controlled study of dialysis patients

Directory of Open Access Journals (Sweden)

Hutchison Alastair J

2013-02-01

Full Text Available Abstract Background This short-term study assessed the efficacy and safety of lanthanum carbonate in the treatment of hyperphosphatemia in dialysis patients; here, we report a prespecified subgroup analysis of patients undergoing peritoneal dialysis. Methods Men and women (n = 39 who had received continuous ambulatory peritoneal dialysis for chronic kidney disease for 6 months or more were enrolled in eight renal medicine departments in the United Kingdom. A 2-week washout period was followed by a 4-week dose-titration phase during which patients received lanthanum carbonate titrated up to 2250 mg/day. This was followed by a 4-week, randomized, placebo-controlled, parallel-group phase during which patients continued to receive either lanthanum carbonate at the titrated dose, or a matched dose of placebo. The main outcome measure was control of serum phosphate levels (1.3-1.8 mmol/l at the end of the parallel-group phase. Results Serum phosphate was controlled in 3/39 (8% patients at the beginning of the dose-titration phase (after washout and in 18/31 (58% patients treated with lanthanum carbonate at its end. After the parallel-group phase, 60% of lanthanum carbonate-treated patients and 10% of those receiving placebo had controlled serum phosphate. There was no difference in mean (95% confidence interval serum phosphate levels between groups at randomization: lanthanum carbonate, 1.57 (1.34-1.81 mmol/l; placebo, 1.58 (1.40-1.76 mmol/l (p = 0.96. However, a difference was seen at the end of the parallel-group phase: lanthanum carbonate, 1.56 (1.33-1.79 mmol/l; placebo, 2.25 (1.81-2.68 mmol/l (p = 0.0015. There were no clinically important changes in nutritional parameters and no serious treatment-related adverse events were recorded. Conclusions At doses up to 2250 mg/day, lanthanum carbonate is well tolerated and controls hyperphosphatemia effectively. Treatment with higher doses of lanthanum carbonate may allow patients undergoing

Photoluminescence properties of cerium oxide nanoparticles as a function of lanthanum content

International Nuclear Information System (INIS)

Deus, R.C.; Cortés, J.A.; Ramirez, M.A.; Ponce, M.A.; Andres, J.; Rocha, L.S.R.

2015-01-01

Highlights: • CeO 2 nanoparticles were obtained by microwave-hydrothermal method. • Rietveld refinement reveals a cubic structure. • KOH mineralizer agent exhibit weak agglomeration at low temperature and shorter time. - Abstract: The structural and photoluminescent properties at room temperature of CeO 2 and La-doped CeO 2 particles were undertaken. The obtained particles were synthesized by a microwave-assisted hydrothermal method (MAH) under different lanthanum contents. X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Fourier transform Raman (FT-Raman), Ultra-violet spectroscopy (UV–vis) and photoluminescence (PL) measurements were carried out. XRD revealed that the powders are free of secondary phases and crystallize in the cubic structure. Raman data show that increasing La doping content increase oxygen vacancies due to lattice expansion. The UV/vis absorption spectroscopy suggested the presence of intermediate energy levels in the band gap of structurally ordered powders. Lanthanum addition creates oxygen vacancies and shifts the photoluminescence in the low energy range leading to intense PL emission

Structures, stabilities, and electronic properties for rare-earth lanthanum doped gold clusters

International Nuclear Information System (INIS)

Zhao, Ya-Ru

2015-01-01

The structures, stabilities, and electronic properties of rare-earth lanthanum doped gold La 2 Au n (n = 1-9) and pure gold Au n (n ≤ 11) clusters have been investigated by using density functional theory. The optimized geometries show that the lowest energy structures of La 2 Au n clusters favour the 3D structure at n ≥ 3. The lanthanum atoms can strongly enhance the stabilities of gold clusters and tend to occupy the most highly coordinated position. By analysing the gap, vertical ionization potential, and chemical hardness, it is found that the La 2 Au 6 isomer possesses higher stability for small-sized La 2 Au n clusters (n = 1-9). The charges in the La 2 Au n clusters transfer from La atoms to the Au n host. In addition, Wiberg bond indices analysis reveals that the intensity of different bonds of La 2 Au n clusters exhibits a sequence of La-La bond > La-Au bond > Au-Au bond.

Induced assembly and photoluminescence of lanthanum (Tb, Eu, Dy) complexes/ZnO/polyethylene glycol hybrid phosphors

Energy Technology Data Exchange (ETDEWEB)

Yan Bing [Department of Chemistry, Tongji University, Siping Road 1239, Shanghai 200092 (China)]. E-mail: byan@tongji.edu.cn; Chen Xi [Department of Chemistry, Tongji University, Siping Road 1239, Shanghai 200092 (China); Wu Jianhua [Department of Chemistry, Tongji University, Siping Road 1239, Shanghai 200092 (China)

2007-08-31

Some novel kinds of hybrid phosphors were assembled with lanthanum (Tb, Eu, Dy) complexes (with four kinds of terbium complexes is 2,4-dihydroxybenzonic acid (DHBA), 1,10-phenanthroline (phen), acetylacetone (AA) and nicotinic acid (Nic), respectively) doped ZnO/PEG particles by co-precipitation approach derived from Zn(CH{sub 3}COO){sub 2} (Zn(AC){sub 2}), NaOH, PEG as precursors at room temperature. The characteristic luminescence spectra for f-f transitions of Tb{sup 3+}, Eu{sup 3+}, Dy{sup 3+} were observed. It is worthy to point out that ZnO is the excellent host for lanthanum ions by the assembly of PEG matrices.

Influence of a solvent on thermodynamics of electrolytic dissociation of simple and complex rare earth salts

Energy Technology Data Exchange (ETDEWEB)

Gorodyskij, A.V.; Fialkov, Yu.Ya.; Chernyj, D.B. (AN Ukrainskoj SSR, Kiev. Inst. Obshchej i Neorganicheskoj Khimii; Kievskij Politekhnicheskij Inst. (Ukrainian SSR))

1982-03-01

Influence of the double mixed solvent on thermodynamic characteristics of ionic migration of lanthanum, neodymium, europium and dysprosium chlorides as well as their phenanthroline complexes is considered. Decrease of lambdasub(c) of simple and complex rare earth salts in the lanthanum, neodymium-europium-dysprosium series as explained by increase of solvation degree, associated with lanthanum compression. It is shown that increase of methanol or propanol content results in exothermicity decrease of the ionic migration process. The temperature constituents of enthalpy and entropy of dissociation of the simple and complex rare earth salts are presented.

Effects of combined flocculant – Lanthanum modified bentonite treatment on aquatic macroinvertebrate fauna

NARCIS (Netherlands)

Waajen, G.; Pauwels, M.; Lürling, M.

2017-01-01

A low dose flocculant (FeCl3), combined with lanthanum modified bentonite (LMB) as phosphate-binding agent, has been applied for eutrophication management in Lake De Kuil (The Netherlands). After the treatment, the state of the lake shifted from hypertrophic to mesotrophic. Although

Effect of pressure on the magnetic properties of lanthanum manganite

International Nuclear Information System (INIS)

Gonchar', L. E.; Leskova, Yu. V.; Nikiforov, A. E.; Kozlenko, D. P.

2010-01-01

The crystalline structure of pure lanthanum manganite under external hydrostatic pressure has been studied. The behavior of magnetic properties and nuclear magnetic resonance (NMR) spectra under these conditions is theoretically predicted. It is shown that an increase in the Neel temperature with pressure is not only caused by the general contraction of the crystal, but is also related to certain peculiarities in the baric behavior of the orbital structure.

Uranyl(VI) and lanthanum(III) complexes with functionalized macrocyclic and macroacyclic Schiff bases

International Nuclear Information System (INIS)

Aguiari, A.; Brianese, N.; Tamburini, S.; Vigato, P.A.

1995-01-01

Acyclic Schiff bases have been prepared by [2 + 1] condensation of 2,6-diformyl-4-chlorophenol and H 2 NCH 2 [CH 2 XCH 2 ] n CH 2 NH 2 (n =3D 0 H 2 -I; X =3D NH, S, O n =3D 1 H 2 -II...H 2 -IV; X =3D 0 n =3D 2 H 2 -V; X =3D 0 n =3D 3 H 2 -VI). The related uranlyl(VI) and lanthanum (III) complexes have bee synthesized by reaction by reaction of the preformed ligands with the appropriate salt or by the template procedure, in the presence of base. No base was employed in the preparation of lanthanum (III) complexes, La(H 2 -II)(NO 3 ) 3 , La(H 2 -IV)(NO 3 ) 3 where the Schiff bases coordinate as neutral chelate ligands. These acyclic complexes have been used for further condensation, and symmetric and asymmetric cyclic complexes have been obtained by their reaction with the polyamines H 2 NCH 2 [CH 2 XCH 2 ]nCH 2 NH 2 or with 4,4'-diaminodibenzo -18-crown-6. By reaction with 4-aminobenzo-15-crown-5 or 2-amino-methyl-15-crown-5, the same acyclic complexes give rise to functionalized complexes bearing crown-ether moieties. Analogously, the acyclic ligand H 3 -IXX, prepared by condensation of 2,6 diformyl-4-chlorophenol and tris(aminoethyl)amine, forms mono and homodinuclear lanthanum (III) complexes, which may undergo further condensation when reacted with primary functionalized amines. (authors). 42 refs., 2 figs., 2 schemes, 1 tab

Near fifty percent sodium substituted lanthanum manganites—A potential magnetic refrigerant for room temperature applications

Energy Technology Data Exchange (ETDEWEB)

Sethulakshmi, N.; Anantharaman, M. R., E-mail: mraiyer@yahoo.com [Department of Physics, Cochin University of Science and Technology, Cochin 682022, Kerala (India); Al-Omari, I. A. [Department of Physics, Sultan Qaboos University, PC 123 Muscat, Sultanate of Oman (Oman); Suresh, K. G. [Department of Physics, Indian Institute of Technology Bombay, Powai, Mumbai 400076 (India)

2014-03-03

Nearly half of lanthanum sites in lanthanum manganites were substituted with monovalent ion-sodium and the compound possessed distorted orthorhombic structure. Ferromagnetic ordering at 300 K and the magnetic isotherms at different temperature ranges were analyzed for estimating magnetic entropy variation. Magnetic entropy change of 1.5 J·kg{sup −1}·K{sup −1} was observed near 300 K. An appreciable magnetocaloric effect was also observed for a wide range of temperatures near 300 K for small magnetic field variation. Heat capacity was measured for temperatures lower than 300 K and the adiabatic temperature change increases with increase in temperature with a maximum of 0.62 K at 280 K.

Cerium(terbium, erbium)chloride-choline chloride aqueous systems

International Nuclear Information System (INIS)

Gajfutdinova, R.K.; Zhuravlev, E.F.; Bikbaeva, G.G.; Domrachev, V.N.; Vanskova, G.I.

1985-01-01

To clarify the effect of rare earth nature on mutual solubility of rare earth salts and amines the solubility of solid phases in the systems, consisting of choline chloride, water and cerium, terbium, erbium chlorides, has been studied. It is established, that solubility isotherms of all the systems, testify to the formation of new solid phases of the composition: Ce(Tb, Er)xCl 3 x2C 5 H 14 ONClx3H 2 O. Individuality of new solid phases is proved by DTA method, the composition is confirmed by chemical analysis and data of PMR spectra, for choline chloride and its complexes with rare earth chlorides of the given composition PMR and IR spectra are studied

Method of producing a solution of radioactive lanthanum-140 from radioactive barium-140 in an isotope generator and installation to carry out the method

International Nuclear Information System (INIS)

Akerman, K.; Jacobs, G.; Sauerwein, K.

1979-01-01

A method of separating radioactive lanthanum-140 from radioactive Ba-140 is proposed. The lanthanum-140 will be washed out of a sulphate precipitate and separated from Ba-140-sulphate by a granular filter mass of CaSO 4 and BaSO 4 . Details of the process are given. (UWI) [de

Investigation of lanthanum- and neodymium ion interaction with potassium polyphosphate in aqueous solution

International Nuclear Information System (INIS)

Ezhova, Zh.A.; Tananaev, I.V.; Koval', E.M.

1983-01-01

A study was made on the interaction in the LaCl 3 -KPO 3 -H 2 O and NdCl 3 -KPO 3 -H 2 O systems at 0 deg C by methods of solubility of residual concentrations and measurement of the pH value. The formation of binary KLa 2 (PO 3 ) 7 x10H 2 O and KLa(PO 3 ) 4 X5H 2 O lanthanum- and potassium polyphosphates, as well as KNd 2 (PO 3 ) 7 X10H 2 O and KNd(PO 3 ) 4 X5H 2 O neodymium- apd potassiUm polyphasphates was established. Chemical, paper-chromatographic, infrared spectroscopic, X-ray diffraction and differential thermal analyses of the prepared compoUnds were conducted. Anhydrous binary lanthanum- and neodymium polyphosphates with potassium-=Kla(PO 3 ) 4 , KNd(PO 3 ) 4 , KLa 2 (PO 3 ) 7 and KNd 2 x(PO 3 ) 7 - eere prepared

Photoluminescence properties of cerium oxide nanoparticles as a function of lanthanum content

Energy Technology Data Exchange (ETDEWEB)

Deus, R.C. [Universidade Estadual Paulista, Unesp —Faculdade de Engenharia de Guaratinguetá, Av. Dr Ariberto Pereira da Cunha 333, Bairro Pedregulho, P.O. Box 355, 12.516-410 Guaratinguetá, São Paulo, Brazil, (Brazil); Cortés, J.A., E-mail: leandrosrr89@gmail.com [Universidade Estadual Paulista, Unesp —Faculdade de Engenharia de Guaratinguetá, Av. Dr Ariberto Pereira da Cunha 333, Bairro Pedregulho, P.O. Box 355, 12.516-410 Guaratinguetá, São Paulo, Brazil, (Brazil); Ramirez, M.A. [Universidade Estadual Paulista, Unesp —Faculdade de Engenharia de Guaratinguetá, Av. Dr Ariberto Pereira da Cunha 333, Bairro Pedregulho, P.O. Box 355, 12.516-410 Guaratinguetá, São Paulo, Brazil, (Brazil); Ponce, M.A. [Instituto de Investigaciones en Ciencia y Tecnología de Materiales (INTEMA) (CONICET-Universidad Nacional de Mar del Plata), Juan B. Justo 4302, 7600 Mar del Plata (Argentina); Andres, J. [Laboratório Interdisciplinar em Cerâmica, Instituto de Química, Universidade Estadual Paulista, P.O. Box 355, 14801-907 Araraquara, São Paulo (Brazil); Rocha, L.S.R. [Universidade Estadual Paulista, Unesp —Faculdade de Engenharia de Guaratinguetá, Av. Dr Ariberto Pereira da Cunha 333, Bairro Pedregulho, P.O. Box 355, 12.516-410 Guaratinguetá, São Paulo, Brazil, (Brazil); and others

2015-10-15

Highlights: • CeO{sub 2} nanoparticles were obtained by microwave-hydrothermal method. • Rietveld refinement reveals a cubic structure. • KOH mineralizer agent exhibit weak agglomeration at low temperature and shorter time. - Abstract: The structural and photoluminescent properties at room temperature of CeO{sub 2} and La-doped CeO{sub 2} particles were undertaken. The obtained particles were synthesized by a microwave-assisted hydrothermal method (MAH) under different lanthanum contents. X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Fourier transform Raman (FT-Raman), Ultra-violet spectroscopy (UV–vis) and photoluminescence (PL) measurements were carried out. XRD revealed that the powders are free of secondary phases and crystallize in the cubic structure. Raman data show that increasing La doping content increase oxygen vacancies due to lattice expansion. The UV/vis absorption spectroscopy suggested the presence of intermediate energy levels in the band gap of structurally ordered powders. Lanthanum addition creates oxygen vacancies and shifts the photoluminescence in the low energy range leading to intense PL emission.

Lanthanum-modified bentonite: potential for efficient removal of phosphates from fishpond effluents.

Science.gov (United States)

Kurzbaum, Eyal; Raizner, Yasmin; Cohen, Oded; Rubinstein, Guy; Bar Shalom, Oded

2017-06-01

Adsorption has been suggested as an effective method for removing phosphates from agricultural wastewater effluents that contain relatively high phosphate concentrations. The present study focused on the use of a bentonite-lanthanum clay (Phoslock ® ) for reducing the dissolved phosphate concentration in fishpond effluents. Batch experiments with synthetic phosphate-spiked solutions and with fishpond effluents were performed in order to determine adsorption equilibrium isotherms and kinetics as well as to determine the efficiency of Phoslock ® in removing phosphate from these solutions. In the synthetic phosphate-spiked solution, the mean maximum phosphate adsorption capacity was 92 mg Phoslock ® /mg phosphate removal. A ratio of 50, 100, and 200 mg Phoslock ® /mg phosphate removal was found for complete phosphate removal from the fishpond effluents, where higher doses of Phoslock ® led to a faster removal rate (94% removal within the first 150 min). These results show that bentonite-lanthanum clay can be employed for designing a treatment process for efficient phosphate removal from fishpond effluents.

Chemically produced nanostructured ODS-lanthanum oxide-tungsten composites sintered by spark plasma

International Nuclear Information System (INIS)

Yar, Mazher Ahmed; Wahlberg, Sverker; Bergqvist, Hans; Salem, Hanadi G.; Johnsson, Mats; Muhammed, Mamoun

2011-01-01

High purity W and W-0.9La 2 O 3 (wt.%) nanopowders were produced by a wet chemical route. The precursor was prepared by the reaction of ammonium paratungstate (APT) with lanthanum salt in aqueous solutions. High resolution electron microscopy investigations revealed that the tungstate particles were coated with oxide precipitates. The precursor powder was reduced to tungsten metal with dispersed lanthanum oxide. Powders were consolidated by spark plasma sintering (SPS) at 1300 and 1400 o C to suppress grain growth during sintering. The final grain size relates to the SPS conditions, i.e. temperature and heating rate, regardless of the starting powder particle size. Scanning electron microscopy revealed that oxide phases were mainly accumulated at grain boundaries while the tungsten matrix constituted of nanosized sub-grains. The transmission electron microscopy revealed that the tungsten grains consist of micron-scale grains and finer sub-grains. EDX analysis confirmed the presence of W in dispersed oxide phases with varying chemical composition, which evidenced the presence of complex oxide phases (W-O-La) in the sintered metals.

Simultaneous determination of dopamine, uric acid and nitrite using carboxylated graphene oxide/lanthanum modified electrode

International Nuclear Information System (INIS)

Ye, Fengying; Feng, Chenqi; Jiang, Jibo; Han, Sheng

2015-01-01

Highlights: • The carboxylated graphene oxide/lanthanum-modified glassy carbon electrode (GO-COOLa/GCE) was successfully utilized for the simultaneous detection and quantification of DA, UA and NO 2 − . • Combining the benefits of carboxylated graphene oxide and lanthanum, the modified sensor displayed large peak separations, long linear ranges and low detection limits for simultaneously detecting DA, UA and NO 2 − . • The GO-COOLa/GCE electrode showed well stability, good repeatability, rapid response, and high catalytic performance toward the oxidations of DA, UA and NO 2 − . - Abstract: A bare glassy carbon electrode (GCE) was reformed by carboxylated graphene oxide/lanthanum, and the modified electrode, called GO-COOLa/GCE, was fabricated for simultaneously detecting dopamine (DA), uric acid (UA) and nitrite (NO 2 − ) by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and amperometry. Several factors which affected the electrocatalytic activity of the GO-COOLa/GCE electrode, such as the effect of pH, scan rate and concentration were studied. Due to the combination of carboxylated graphene oxide and lanthanum ions, the GO-COOLa/GCE sensor showed rapid response, excellent selectivity and high catalytic performance toward the electrooxidation of DA, UA and NO 2 − . In optimized conditions, two linear response ranges for determining DA were obtained over ranges of 0.01-1.96×10 2 μM and 1.96×10 2 -1.23×10 3 μM with detection limit of 0.018 μM (S/N = 3). And the responses of the GO-COOLa/GCE electrode for UA and NO 2 − were linear in the region of 1-1.53×10 3 μM and 1-2.75×10 3 μM with detection limits of 0.058 μM and 0.070 μM, respectively. Furthermore, this reformed electrode was successfully used to the detection of DA, UA and NO 2 − in real urine and serum samples, showing its promising application in the electroanalysis of real samples.

Determination of Aluminum in Dialysis Concentrates by Atomic Absorption Spectrometry after Coprecipitation with Lanthanum Phosphate.

Science.gov (United States)

Selvi, Emine Kılıçkaya; Şahin, Uğur; Şahan, Serkan

2017-01-01

This method was developed for the determination of trace amounts of aluminum(III) in dialysis concentrates using atomic absorption spectrometry after coprecipitation with lanthanum phosphate. The analytical parameters that influenced the quantitative coprecipitation of analyte including amount of lanthanum, amount of phosfate, pH and duration time were optimized. The % recoveries of the analyte ion were in the range of 95-105 % with limit of detection (3s) of 0.5 µg l -1 . Preconcentration factor was found as 1000 and Relative Standard Deviation (RSD) % value obtained from model solutions was 2.5% for 0.02 mg L -1 . The accuracy of the method was evaluated with standard reference material (CWW-TMD Waste Water). The method was also applied to most concentrated acidic and basic dialysis concentrates with satisfactory results.

PROCESS USING POTASSIUM LANTHANUM SULFATE FOR FORMING A CARRIER PRECIPITATE FOR PLUTONIUM VALUES

Science.gov (United States)

Angerman, A.A.

1958-10-21

A process is presented for recovering plutonium values in an oxidation state not greater than +4 from fluoride-soluble fission products. The process consists of adding to an aqueous acidic solution of such plutonium values a crystalline potassium lanthanum sulfate precipitate which carries the plutonium values from the solution.

海藻酸镧颗粒除氟研究：吸附剂物性和吸附机理%Fluoride Removal by Lanthanum Alginate Bead:Adsorbent Characterization and Adsorption Mechanism

Institute of Scientific and Technical Information of China (English)

霍亚坤; 丁文明; 黄霞; 徐静年; 赵梦华

2011-01-01

Lanthanum alginate bead is a new, highly active adsorbent. In the present study, we investigated its adsorption performance and its adsorption mechanism. The adsorption isotherm for fluoride onto lanthanum alginate bead fits the Langmuir model well, and the maximum adsorption capacity is 197.2 mg·g-1. X-ray diffraction shows the amorphous nature of lanthanum alginate bead, which allows for better accessibility to fluoride and thus better activity. Infrared spectra of lanthanum alginate bead before and after adsorption confirm its stable skeletal structure.Scanning electron microscopy shows that the dense surface structure of the adsorbent appear cracks after adsorption.The adsorption mechanism of lanthanum alginate bead is considered as an ion exchange between F- and Cl- or OH-,as verified from the adsorbent and the solution by pH effect, energy dispersive X-ray, and ion chromatography.

Inductively coupled plasma optical emission spectrometry analysis of lanthanum, samarium and gadolinium oxides for rare earths impurities

International Nuclear Information System (INIS)

Reino, L.C.P.; Lordello, A.R.

1990-09-01

An inductively coupled plasma optical emission spectrometry method is described for the determination of Sm, Eu, La, Gd, Dy, Pr, Ho, Nd, Tb and Y in purified oxides of lanthanum, samarium and gadolinium. The method enables a simple, precise and readily available determination. Dissolution of the samples is achieved with diluted hydrochloric acid (1:1). The solutions are diluted to volume for a concentration of 1mg/ml. The lowest determination limit is 0,01% for most elements and 0,05 or 0,1% for a few rare earths in samarium and gadolinium matrices. Lanthanum, Samarium and Gadolinium concentrates with purity grade of 99,9%, 99,6% and 99,8%, respectively, can be analysed by this procedure. (author)

Chloride ingress prediction

DEFF Research Database (Denmark)

Frederiksen, Jens Mejer; Geiker, Mette Rica

2008-01-01

Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents experimentally based design parameters for Portland cement concretes with and without silica fume and fly ash...... in marine atmospheric and submersed South Scandinavian environment. The design parameters are based on sequential measurements of 86 chloride profiles taken over ten years from 13 different types of concrete. The design parameters provide the input for an analytical model for chloride profiles as function...... of depth and time, when both the surface chloride concentration and the diffusion coefficient are allowed to vary in time. The model is presented in a companion paper....

The oxidation of carbon monoxide over transition metal doped lanthanum manganates nanoparticles

International Nuclear Information System (INIS)

Fal Desai, M.S.; Salker, A.V.

2012-01-01

Lanthanum manganates perovskites (ABO 3 ) has been widely studied and applied. Many perovskites with A and B sites doped with different metals show good catalytic activity in many oxidation reactions than the individual perovskite. In present study, an attempt has been made to show comparative account of CO oxidation by doping the B site with different cations using sol-gel method

METHOD OF SEPARATING URANIUM VALUES, PLUTONIUM VALUES AND FISSION PRODUCTS BY CHLORINATION

Science.gov (United States)

Brown, H.S.; Seaborg, G.T.

1959-02-24

The separation of plutonium and uranium from each other and from other substances is described. In general, the method comprises the steps of contacting the uranium with chlorine in the presence of a holdback material selected from the group consisting of lanthanum oxide and thorium oxide to form a uranium chloride higher than uranium tetrachloride, and thereafter heating the uranium chloride thus formed to a temperature at which the uranium chloride is volatilized off but below the volatilizalion temperature of plutonium chloride.

Thermal stability and microstructure of catalytic alumina composite support with lanthanum species

Science.gov (United States)

Ozawa, Masakuni; Nishio, Yoshitoyo

2016-09-01

Lanthanum (La) modified γ-alumina composite was examined for application toward thermostable catalytic support at elevated temperature. La added alumina was prepared through an aqueous process using lanthanum (III) nitrate and then characterized by surface area measurement, X-ray powder diffraction (XRD), differential thermal analysis (DTA), scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray photoemission spectroscopy (XPS) and surface desorption of CO2. It was found that the properties depended on the La content and heat treatment temperatures. The characterization of the surface, structural and chemical properties of La-Al2O3 showed the existence of a strong interaction between the La species and alumina via formation of new phase and modified surface in Al2O3 samples. LaAlO3 nanoparticle formed among alumina particles by the solid phase reaction of Al2O3 and La2O3. The increase of the surface basicity of La modified alumina was demonstrated using CO2 temperature programmed desorption experiments. The controlled surface interaction between La oxide and alumina provide the unique surface and structural properties of the resulting mixed oxides as catalysts and catalytic supports.

Chloride Test

Science.gov (United States)

... metabolic acidosis ) or when a person hyperventilates (causing respiratory alkalosis ). A decreased level of blood chloride (called hypochloremia) ... disease , emphysema or other chronic lung diseases (causing respiratory ... metabolic alkalosis). An increased level of urine chloride can indicate ...

Melt-assisted synthesis to lanthanum hexaboride nanoparticles and ...

Indian Academy of Sciences (India)

2017-09-22

Sep 22, 2017 ... cubes (100–300 nm) when metal zinc was used as reaction melt. Photothermal ... powder (Zn, AR), potassium chloride (KCl, AR), sodium chloride (NaCl, AR) and ... ized water to remove NaCl, KCl and other impurities. The.

Cost-Effectiveness of First-Line Sevelamer and Lanthanum versus Calcium-Based Binders for Hyperphosphatemia of Chronic Kidney Disease.

Science.gov (United States)

Habbous, Steven; Przech, Sebastian; Martin, Janet; Garg, Amit X; Sarma, Sisira

2018-03-01

Phosphate binders are used to treat hyperphosphatemia among patients with chronic kidney disease (CKD). To conduct an economic evaluation comparing calcium-free binders sevelamer and lanthanum with calcium-based binders for patients with CKD. Effectiveness data were obtained from a recent meta-analysis of randomized trials. Effectiveness was measured as life-years gained and translated to quality-adjusted life-years (QALYs) using utility weights from the literature. A Markov model consisting of non-dialysis-dependent (NDD)-CKD, dialysis-dependent (DD)-CKD, and death was developed to estimate the incremental costs and effects of sevelamer and lanthanum versus those of calcium-based binders. A lifetime horizon was used and both costs and effects were discounted at 1.5%. All costs are presented in 2015 Canadian dollars from the Canadian public payer perspective. Results of probabilistic sensitivity analysis were presented using cost-effectiveness acceptability curves. Sensitivity analyses were conducted for risk pooling methods, omission of dialysis costs, and persistence of drug effects on mortality. Sevelamer resulted in an incremental cost-effectiveness ratio of $106,522/QALY for NDD-CKD and $133,847/QALY for DD-CKD cohorts. Excluding dialysis costs, sevelamer was cost-effective in the NDD-CKD cohort ($5,847/QALY) and the DD-CKD cohort ($11,178/QALY). Lanthanum was dominated regardless of whether dialysis costs were included. Existing evidence does not clearly support the cost-effectiveness of non-calcium-containing phosphate binders (sevelamer and lanthanum) relative to calcium-containing phosphate binders in DD-CKD patients. Our study suggests that sevelamer may be cost-effective before dialysis onset. Because of the remaining uncertainty in several clinically relevant outcomes over time in DD-CKD and NDD-CKD patients, further research is encouraged. Copyright © 2018 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier

Synthesis and Stability of Lanthanum Superhydrides

Energy Technology Data Exchange (ETDEWEB)

Geballe, Zachary M. [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Liu, Hanyu [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Mishra, Ajay K. [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Permanent address: HP& SRPD, Bhabha Atomic Research Center, Mumbai-85 India; Ahart, Muhtar [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Somayazulu, Maddury [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Meng, Yue [HPCAT, Geophysical Laboratory, Carnegie Institution of Washington, Argonne IL 60439 USA; Baldini, Maria [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Hemley, Russell J. [Institute of Materials Science and Department of Civil and Environmental Engineering, The George Washington University, Washington DC 20052 USA

2017-12-15

Recent theoretical calculations predict that megabar pressure stabilizes very hydrogen-rich simple compounds having new clathrate-like structures and remarkable electronic properties including room-temperature superconductivity. X-ray diffraction and optical studies demonstrate that superhydrides of lanthanum can be synthesized with La atoms in an fcc lattice at 170 GPa upon heating to about 1000 K. The results match the predicted cubic metallic phase of LaH10 having cages of thirty-two hydrogen atoms surrounding each La atom. Upon decompression, the fcc-based structure undergoes a rhombohedral distortion of the La sublattice. The superhydride phases consist of an atomic hydrogen sublattice with H-H distances of about 1.1 Å, which are close to predictions for solid atomic metallic hydrogen at these pressures. With stability below 200 GPa, the superhydride is thus the closest analogue to solid atomic metallic hydrogen yet to be synthesized and characterized.

Cerium-activated lanthanum beryllate as a gamma detector material

International Nuclear Information System (INIS)

Czirr, J.B.; Berrondo, M.

1994-01-01

The authors have tested a single crystal of Ce-activated lanthanum beryllate BEL(Ce) as a potential gamma detector material. The density (6.1 g.cm -3 ) and decay time (50 ns) are competitive with other recently developed materials. The scintillation efficiency is 57 to 95% that of BGO. For an excitation wavelength of 340 nm, the emission spectra is a broad peak centered at 450 mn. The H 2 annealed sample is transparent for wavelengths greater than 400 mn. They are continuing a program to improve the scintillation efficiency by varying the crystal growth conditions

Synthesis of calcium doped lanthanum manganite by mechanosynthesis

International Nuclear Information System (INIS)

Bolarin, A.M.; Sanchez, F.; Palomares, S.; Aguilar, J.A.; Torres-Villasenor, G.

2007-01-01

Lanthanum manganite doped with calcium, Ca 1/3 La 2/3 MnO 3-δ , was prepared by a high-energy ball milling. The precursors used were Mn 2 O 3 , La 2 O 3 and CaO, mixed in the stoichiometric ratio to obtain this manganite. The mechano-chemical process was performed at room temperature in a SPEX 8000D mixer/mill, using hardened steel balls and stainless steel vials, in air atmosphere. X-ray diffraction was used to elucidate the phase transformation as a function of the milling time. The Rietveld refinement was used in order to characterize structurally the manganites. The morphology and particle size of powder compound obtained were characterized by scanning electron microscope. The particle size of this powder material was measured with zeta size analyzer, and selected area electron diffraction (SAED) from TEM was used to elucidate the crystalline structure of this powder compound. The results showed that it is possible to obtain calcium doped lanthanum manganite by mechano-synthesis, using a weight ratio of ball to powder of 12:1, after 3 h of milling. The evolution of the phase transformation during the milling time is reported. Increases in milling time produce exponential decrease in the particle size, up to 680 nm after 1 h of milling. After the milling process it is obtained a powder compound with an orthorhombic structure (S.G. Pbnm). A prolonged milling time (>9 h) produce an important reduction in the particle size but this is accompanied with a high iron contamination caused by metallic residues originated from vial and balls and also, after 9 h of milling time, it was found an important distortion in orthorhombic structure, obtaining two types of parameters

Solid state interaction studies on binary nitrate mixtures of uranyl nitrate hexahydrate and lanthanum nitrate hexahydrate at elevated temperatures

Energy Technology Data Exchange (ETDEWEB)

Kalekar, Bhupesh; Raje, Naina, E-mail: nraje@barc.gov.in; Reddy, A.V.R.

2017-02-15

Interaction behavior of uranyl nitrate hexahydrate (UNH) and lanthanum nitrate hexahydrate (LaNH) have been investigated on the mixtures in different molar ratios of the two precursors and monitoring the reactions at elevated temperatures with thermoanalytical and X-ray diffraction measurement techniques. During the decomposition of equimolar mixture of LaNH and UNH, formation of lanthanum uranate (U{sub 0.5}La{sub 0.5})O{sub 2}, was seen by the temperature of 500 °C along with lanthanum oxide (La{sub 2}O{sub 3}) and uranium trioxide (UO{sub 3}). By the temperature of 700 °C, the formation of uranium sesquioxide (U{sub 3}O{sub 8}) was observed along with (U{sub 0.5}La{sub 0.5})O{sub 2} as end products in uranium rich mixtures. Lanthanum rich compositions decomposed by the temperature of 700 °C to give (U{sub 0.5}La{sub 0.5})O{sub 2} and La{sub 2}O{sub 3} as end products. - Highlights: • UO{sub 2}(NO{sub 3}){sub 2}.6H{sub 2}O and La(NO{sub 3}){sub 3}.6H{sub 2}O interact through their intermediates. • Formation of (U{sub 0.5}La{sub 0.5})O{sub 2} by 500 °C. • La deficient mixtures decompose to give U{sub 3}O{sub 8} and (U{sub 0.5}La{sub 0.5})O{sub 2} as end products. • La rich mixtures decompose to give La{sub 2}O{sub 3} and (U{sub 0.5}La{sub 0.5})O{sub 2} as end product.

40 CFR 61.65 - Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants.

Science.gov (United States)

2010-07-01

... dichloride, vinyl chloride and polyvinyl chloride plants. 61.65 Section 61.65 Protection of Environment... AIR POLLUTANTS National Emission Standard for Vinyl Chloride § 61.65 Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants. An owner or operator of an ethylene dichloride...

Paramagnetic centers in two phases of manganese-doped lanthanum gallate

Science.gov (United States)

Vazhenin, V. A.; Potapov, A. P.; Guseva, V. B.; Artyomov, M. Yu.

2009-05-01

An EPR study of two phases of manganese-doped lanthanum gallate (with a first-order structural transition occurring at 430 K) has revealed Gd3+, Fe3+, and Mn4+ centers at room temperature and 438 K. The parameters of spin Hamiltonians are determined for the Gd3+, Fe3+, and Mn4+ rhombohedral centers in the high-temperature phase (with no other centers found here) and for the monoclinic center Gd3+ in the low-temperature phase. Both in the orthorhombic and in the rhombohedral phase, crystallographic twins (or ferroelastic domains) are observed.

Lanthanum gallate substrates for epitaxial high-temperature superconducting thin films

Science.gov (United States)

Sandstrom, R. L.; Giess, E. A.; Gallagher, W. J.; Segmuller, A.; Cooper, E. I.

1988-11-01

It is demonstrated that lanthanum gallate (LaGaO3) has considerable potential as an electronic substrate material for high-temperature superconducting films. It provides a good lattice and thermal expansion match to YBa2Cu3O(7-x), can be grown in large crystal sizes, is compatible with high-temperature film processing, and has a reasonably low dielectric constant and low dielectric losses. Epitaxial YBa2Cu3O(7-x) films grown on LaGaO3 single-crystal substrates by three techniques have zero resistance between 87 and 91 K.

Bordoni relaxation and magnetic transformation in cerium and cerium-lanthanum alloys

Energy Technology Data Exchange (ETDEWEB)

Postnikov, V S; Polner, G L; Sharshakov, I M

1975-11-01

The internal friction in pure cerium and cerium-base alloys with 2.5 and 12 weight percent of lanthanum added at temperature ranging from 4.2 deg up to 77/sup 0/K is described. Amplitude-independent internal friction has been measured with an inverse torsion pendulum with a specimen oscillation frequency of 1-30 hz in vacuum not less than 1.10/sup -5/ torr. A temperature of the specimen has been determined with a capacitance-type sensor and a gas gage. A curve showing the dependence of internal friction upon a temperature of pure cerium has two distinct peaks; the first at 12.5/sup 0/K, the second at 45/sup 0/K. The 12.5/sup 0/K peak is accounted for by a transition of antiferromagnetic ..beta..-Ce into a paramagnetic state. The 45/sup 0/K peak is a Bordoni maximum. The paper describes an influence of additions, specimen oscillation frequency variations, deformation and annealing upon the peak behavor. Added lanthanum reduces not only a peak temperature but a height as well. Studies of the 45/sup 0/K peak have shown that its temperature location depends upon the specimen oscillation frequency. As the frequency increases the peak tends to a range of high temperatures which confirms its relaxation nature.

Phases in lanthanum-nickel-aluminum alloys

International Nuclear Information System (INIS)

Mosley, W.C.

1992-01-01

Lanthanum-nickel-aluminum (LANA) alloys will be used to pump, store and separate hydrogen isotopes in the Replacement Tritium Facility (RTF). The aluminum content (y) of the primary LaNi 5 -phase is controlled to produce the desired pressure-temperature behavior for adsorption and desorption of hydrogen. However, secondary phases cause decreased capacity and some may cause undesirable retention of tritium. Twenty-three alloys purchased from Ergenics, Inc. for development of RTF processes have been characterized by scanning electron microscopy (SEM) and by electron microprobe analysis (EMPA) to determine the distributions and compositions of constituent phases. This memorandum reports the results of these characterization studies. Knowledge of the structural characteristics of these alloys is a useful first step in selecting materials for specific process development tests and in interpreting results of those tests. Once this information is coupled with data on hydrogen plateau pressures, retention and capacity, secondary phase limits for RTF alloys can be specified

Synthesis and stability of lanthanum superhydrides

Energy Technology Data Exchange (ETDEWEB)

Geballe, Zachary M.; Liu, Hanyu; Mishra, Ajay K.; Ahart, Muhtar; Somayazulu, Maddury; Baldini, Maria [Geophysical Laboratory, Carnegie Institution, Washington, DC (United States); Meng, Yue [HPCAT, Geophysical Laboratory, Carnegie Institution of Washington, Argonne, IL (United States); Hemley, Russell J. [Institute of Materials Science and Department of Civil and Environmental Engineering, The George Washington University, Washington, DC (United States)

2018-01-15

Recent theoretical calculations predict that megabar pressure stabilizes very hydrogen-rich simple compounds having new clathrate-like structures and remarkable electronic properties including room-temperature superconductivity. X-ray diffraction and optical studies demonstrate that superhydrides of lanthanum can be synthesized with La atoms in an fcc lattice at 170 GPa upon heating to about 1000 K. The results match the predicted cubic metallic phase of LaH{sub 10} having cages of thirty-two hydrogen atoms surrounding each La atom. Upon decompression, the fcc-based structure undergoes a rhombohedral distortion of the La sublattice. The superhydride phases consist of an atomic hydrogen sublattice with H-H distances of about 1.1 Aa, which are close to predictions for solid atomic metallic hydrogen at these pressures. With stability below 200 GPa, the superhydride is thus the closest analogue to solid atomic metallic hydrogen yet to be synthesized and characterized. (copyright 2018 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Chloride flux in phagocytes.

Science.gov (United States)

Wang, Guoshun

2016-09-01

Phagocytes, such as neutrophils and macrophages, engulf microbes into phagosomes and launch chemical attacks to kill and degrade them. Such a critical innate immune function necessitates ion participation. Chloride, the most abundant anion in the human body, is an indispensable constituent of the myeloperoxidase (MPO)-H2 O2 -halide system that produces the potent microbicide hypochlorous acid (HOCl). It also serves as a balancing ion to set membrane potentials, optimize cytosolic and phagosomal pH, and regulate phagosomal enzymatic activities. Deficient supply of this anion to or defective attainment of this anion by phagocytes is linked to innate immune defects. However, how phagocytes acquire chloride from their residing environment especially when they are deployed to epithelium-lined lumens, and how chloride is intracellularly transported to phagosomes remain largely unknown. This review article will provide an overview of chloride protein carriers, potential mechanisms for phagocytic chloride preservation and acquisition, intracellular chloride supply to phagosomes for oxidant production, and methods to measure chloride levels in phagocytes and their phagosomes. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Atom states and interatomic interactions in complex perovskite-like oxides. Communication XX. Origin of electron-ionic conductivity in lanthanum gallates doped with strontium and chromium

International Nuclear Information System (INIS)

Chezhina, N.V.; Zolotukhina, N.V.; Pijr, I.V.

2006-01-01

Magnetic susceptibilities and electric conductivities of solid solutions based on lanthanum gallate containing chromium and strontium atoms in the ratio of 10 : 2 were studied. It was shown that no partial oxidation of chromium to Cr(IV) occurs when lanthanum gallate is doped with chromium and strontium simultaneously, whereas the ionic conductivity is associated with the appearance of vacancies stabilized by chromium atoms in the oxygen sublattice [ru

Influence of Chloride-Ion Adsorption Agent on Chloride Ions in Concrete and Mortar

Directory of Open Access Journals (Sweden)

Gai-Fei Peng

2014-04-01

Full Text Available The influence of a chloride-ion adsorption agent (Cl agent in short, composed of zeolite, calcium aluminate hydrate and calcium nitrite, on the ingress of chloride ions into concrete and mortar has been experimentally studied. The permeability of concrete was measured, and the chloride ion content in mortar was tested. The experimental results reveal that the Cl agent could adsorb chloride ions effectively, which had penetrated into concrete and mortar. When the Cl agent was used at a dosage of 6% by mass of cementitious materials in mortar, the resistance to the penetration of chloride ions could be improved greatly, which was more pronounced when a combination of the Cl agent and fly ash or slag was employed. Such an effect is not the result of the low permeability of the mortar, but might be a result of the interaction between the Cl agent and the chloride ions penetrated into the mortar. There are two possible mechanisms for the interaction between the Cl agent and chloride ion ingress. One is the reaction between calcium aluminate hydrate in the Cl agent and chloride ions to form Friedel’s salt, and the other one is that calcium aluminate hydrate reacts with calcium nitrite to form AFm during the early-age hydration of mortar and later the NO2− in AFm is replaced by chloride ions, which then penetrate into the mortar, also forming Friedel’s salt. More research is needed to confirm the mechanisms.

Internal-standard method for the determination of uranium, thorium, lanthanum and europium in carbonaceous shale and monazite by epithermal neutron activation analysis

Energy Technology Data Exchange (ETDEWEB)

Chen, Shuenn-Gang; Tsai, Hui-Tuh; Wu, Shaw-Chii [Institute of Nuclear Energy Research, Lung-Tan (Taiwan, Republic of China)

1981-10-03

An internal-standard method was applied for the determination of uranium, thorium, lanthanum and europium is carbonaceous shale samples and monazite sand by epithermal neutron activation analysis using gold as an internal standard element. The samples were irradiated in a zero-power reactor at the Institute of Nuclear Energy Research and measured with a high-resolution Ge(Li) detector. The detection limit is 0.1 ppm for uranium and europium, 1 ppm for thorium, 5 ppm for lanthanum, and the realative error of all elements is within +-2.6%.

Thermodynamics of ionic migration of simple and complex rare earth salts in mixed alcohol solvents

International Nuclear Information System (INIS)

Gorodyskij, A.V.; Fialkov, Yu.Ya.; Chernyj, D.B.

1982-01-01

The influence of the composition of double mixed solvents (water-methanol and methanol-propanol) on thermodynamic characteristics of electrolytic dissociation process-enthalpy and entropy, dissociation constants of chlorides and diphenanthroline chlorides of lanthanum, neodymium, europium and dysprosium, is analyzed. It is shown that when passing from water to methanol, that is, with decrease of dielectric permeability, the endothermicity of electrolytic dissociation process increases

Thermodynamics of ionic migration of simple and complex rare earth salts in mixed alcohol solvents

Energy Technology Data Exchange (ETDEWEB)

Gorodyskij, A.V.; Fialkov, Yu.Ya.; Chernyj, D.B. (AN Ukrainskoj SSR, Kiev. Inst. Obshchej i Neorganicheskoj Khimii; Kievskij Politekhnicheskij Inst. (Ukrainian SSR))

1982-04-01

The influence of the composition of double mixed solvents (water-methanol and methanol-propanol) on thermodynamic characteristics of electrolytic dissociation process-enthalpy and entropy, dissociation constants of chlorides and diphenanthroline chlorides of lanthanum, neodymium, europium and dysprosium, is analyzed. It is shown that when passing from water to methanol, that is, with decrease of dielectric permeability, the endothermicity of electrolytic dissociation process increases.

Relaxation effects in oxygen-conducting oxides on base of lanthanum gallate (La, Sr)(Ga, Me)O3, Me = Mg, Fe

International Nuclear Information System (INIS)

Glavatskikh, T.Yu.; Venskovskij, N.U.; Kaleva, G.M.; Mosunov, A.V.; Politova, E.D.; Stefanovich, S.Yu.

2003-01-01

The dielectric and electric conducting properties of the heterosubstituted perovskite-like solid solutions (La, Sr)(Ga, Me)O 3 , Me Mg, Fe are studied. The increase in the ceramics electric conductivity, conditioned by increase in the ion constituent at strengthening the nonstoichiometry by oxygen and electron constituent by the additional introduction of iron is observed by replacing the part of the lanthanum and gallium cations by strontium, magnesium and iron in the solid solutions on the basis of the lanthanum gallate. The ceramics relaxation behavior is identified; the applicability of the model of the vacational electron transfer for the dipole relaxation is established [ru

Ionic conductivity and fuel cell properties of apatite-type lanthanum silicates doped with Mg and containing excess oxide ions

Energy Technology Data Exchange (ETDEWEB)

Yoshioka, Hideki [Hyogo Prefectural Institute of Technology, 3-1-12 Yukihira-cho, Suma-ku, Kobe 654-0037 (Japan); Nojiri, Yoshihiro [Kyushu University, Department of Mechanical Engineering Science, Faculty of Engineering, Motooka 744, Nishi-ku, Fukuoka 819-0935 (Japan); Tanase, Shigeo [National Institute of Advanced Industrial Science and Technology, 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577 (Japan)

2008-11-30

Enhancement of the ionic conductivity of lanthanum silicate-based apatites is examined with emphasis on optimizing the La composition and the Mg doping level at the same time. La{sub 10}Si{sub 5.8}Mg{sub 0.2}O{sub 26.8} and La{sub 9.8}Si{sub 5.7}Mg{sub 0.3}O{sub 26.4} show the highest level of the ionic conductivities among apatite silicates, 8.8 and 7.4 x 10{sup -} {sup 2} S cm{sup -} {sup 1} at 800 C, respectively, with a very low level of activation energy (0.42-0.43 eV). Their conductivities are higher than yttria stabilized zirconia (YSZ) below 900 C and even comparable to Sr and Mg doped lanthanum gallate (LSGM) below 550 C. A solid oxide fuel cell using La{sub 9.8}Si{sub 5.7}Mg{sub 0.3}O{sub 26.4} as an electrolyte with Ni-ceria cermet anode and Sr doped lanthanum cobaltite cathode exhibits a remarkable improvement in power generation compared to previous data using Pt electrodes. Structural investigation by the Rietveld analysis on the powder X-ray diffraction pattern shows significant enlargement of the bottleneck triangle sizes of the conduction channel with the Mg doping. (author)

Sinterability and conductivity of barium doped aluminium lanthanum oxyapatite La{sub 9.5}Ba{sub 0.5}Si{sub 5.5}Al{sub 0.5}O{sub 26.5} electrolyte of solid oxide fuel cells

Energy Technology Data Exchange (ETDEWEB)

Cao Xiaoguo [Faculty of Materials and Energy, Guangdong University of Technology, Guangzhou 510006, Guangdong (China); Jiang Sanping, E-mail: s.jiang@curtin.edu.au [Fuels and Energy Technology Institute and Department of Chemical Engineering, Curtin University, Perth, WA 6102 (Australia)

2012-05-15

Highlights: Black-Right-Pointing-Pointer Ba doping enhances the sintering and densification properties of aluminium lanthanum apatite. Black-Right-Pointing-Pointer Ba doping improves the oxide conductivity of aluminium lanthanum apatite. Black-Right-Pointing-Pointer The enhancement of Ba doping is mainly due to the significantly reduced grain boundary resistance of the aluminium lanthanum apatite. - Abstract: Apatite ceramics are interesting alternative solid oxide fuel cells (SOFCs) electrolytes because of their open structure for the transportation of oxide ions and their good chemical stability. This study reports the influence of barium doping on the microstructure, sinterability and oxide conductivity properties of the aluminium lanthanum oxyapatite La{sub 9.5}Ba{sub 0.5}Si{sub 5.5}Al{sub 0.5}O{sub 26.5}. SEM results show that lanthanum substitution with barium improves the sinterability of apatite ceramics. The barium doping also enhances the conductivity of the aluminium lanthanum silicates. The oxygen ion conductivity of La{sub 9.5}Ba{sub 0.5}Si{sub 5.5}Al{sub 0.5}O{sub 26.5} sintered at 1600 Degree-Sign C is 2.21 Multiplication-Sign 10{sup -2} S cm{sup -1} at 800 Degree-Sign C, higher than 9.81 Multiplication-Sign 10{sup -3} S cm{sup -1} of La{sub 10}Si{sub 5}AlO{sub 26.5} sample prepared under the same conditions. The results in the present study demonstrate that doping Ba on the La site for aluminium lanthanum oxyapatite reduces the sintering temperature and improves the ion conductivity. The enhancement of Ba dopant is mainly on the improvement of the densification and thus substantially reduced grain boundary resistance of aluminium lanthanum oxyapatite particularly at low temperatures.

In situ XANES cell used for the study of lanthanum strontium cuprate deNOx catalysts

DEFF Research Database (Denmark)

Hagen, Anke

2011-01-01

, maintaining charge neutrality, with the concentration of oxygen vacancies likely increasing at substitution ratios larger than Sr/La>0.08. During heating in air, the valence of copper ions in the structure increased. Upon exposure to NO at 500 °C the valence of copper ions in a lanthanum strontium cuprate...

Chloride test - blood

Science.gov (United States)

Serum chloride test ... A greater-than-normal level of chloride is called hyperchloremia. It may be due to: Carbonic anhydrase inhibitors (used to treat glaucoma) Diarrhea Metabolic acidosis Respiratory alkalosis (compensated) Renal ...

Chloride in diet

Science.gov (United States)

... this page: //medlineplus.gov/ency/article/002417.htm Chloride in diet To use the sharing features on this page, please enable JavaScript. Chloride is found in many chemicals and other substances ...

Mercuric chloride poisoning

Science.gov (United States)

... page: //medlineplus.gov/ency/article/002474.htm Mercuric chloride poisoning To use the sharing features on this page, please enable JavaScript. Mercuric chloride is a very poisonous form of mercury. It ...

Chloride removal from vitrification offgas

Energy Technology Data Exchange (ETDEWEB)

Slaathaug, E.J. [Westinghouse Hanford Co., Richland, WA (United States)

1995-06-01

This study identified and investigated techniques of selectively purging chlorides from the low-level waste (LLW) vitrification process with the purge stream acceptable for burial on the Hanford Site. Chlorides will be present in high concentration in several individual feeds to the LLW Vitrification Plant. The chlorides are highly volatile in combustion type melters and are readily absorbed by wet scrubbing of the melter offgas. The Tank Waste Remediation System (TWRS) process flow sheets show that the resulting chloride rich scrub solution is recycled back to the melter. The chlorides must be purged from the recycle loop to prevent the buildup of excessively high chloride concentrations.

Chloride removal from vitrification offgas

International Nuclear Information System (INIS)

Slaathaug, E.J.

1995-01-01

This study identified and investigated techniques of selectively purging chlorides from the low-level waste (LLW) vitrification process with the purge stream acceptable for burial on the Hanford Site. Chlorides will be present in high concentration in several individual feeds to the LLW Vitrification Plant. The chlorides are highly volatile in combustion type melters and are readily absorbed by wet scrubbing of the melter offgas. The Tank Waste Remediation System (TWRS) process flow sheets show that the resulting chloride rich scrub solution is recycled back to the melter. The chlorides must be purged from the recycle loop to prevent the buildup of excessively high chloride concentrations

Lanthanum gallate substrates for epitaxial high-temperature superconducting thin films

International Nuclear Information System (INIS)

Sandstrom, R.L.; Giess, E.A.; Gallagher, W.J.; Segmueller, A.; Cooper, E.I.; Chisholm, M.F.; Gupta, A.; Shinde, S.; Laibowitz, R.B.

1988-01-01

We demonstrate that lanthanum gallate (LaGaO 3 ) has considerable potential as an electronic substrate material for high-temperature superconducting films. It provides a good lattice and thermal expansion match to YBa 2 Cu 3 O/sub 7-//sub x/, can be grown in large crystal sizes, is compatible with high-temperature film processing, and has a reasonably low dielectric constant (ε≅25) and low dielectric losses. Epitaxial YBa 2 Cu 3 O/sub 7-//sub x/ films grown on LaGaO 3 single-crystal substrates by three techniques have zero resistance between 87 and 91 K

Catalytic activity of lanthanum oxide for the reduction of cyclohexanone

International Nuclear Information System (INIS)

Sugunan, S.; Sherly, K.B.

1994-01-01

Lanthanum oxides, La 2 O 3 has been found to be an effective catalyst for the liquid phase reduction of cyclohexanone. The catalytic activities of La 2 O 3 activated at 300, 500 and 800 degC and its mixed oxides with alumina for the reduction of cylcohexanone with 2-propanol have been determined and the data parallel that of the electron donating properties of the catalysts. The electron donating properties of the catalysts have been determined from the adsorption of electron acceptors of different electron affinities on the surface of these oxides. (author). 15 refs., 2 figs., 1 tab

Characterization of branchial transepithelial calcium fluxes in freshwater trout, Salmo gairdneri

International Nuclear Information System (INIS)

Perry, S.F.; Flik, G.

1988-01-01

Experiments were performed to determine whether gill transepithelial calcium fluxes in the freshwater trout (Salmo gairdneri) are passive or require active transport and to characterize the mechanism involved. A comparison of the in vivo unidirectional flux ratios with the flux ratios calculated according to the transepithelial electrochemical gradients revealed that calcium uptake from the water requires active transport of Ca 2+ . The inhibition of calcium uptake by external lanthanum, the specific deposition of lanthanum on the apical surface of chloride cells, and the favorable electrochemical gradient for calcium across the apical membrane suggest that the initial step in branchial calcium uptake is the passive entry of calcium into the cytosol of chloride cells through apical channels that are permeable to calcium. The study of gill basolateral plasma membrane vesicles demonstrated the existence of a high-affinity calmodulin-dependent calcium-transporting system. This system actively transports calcium from the cytosol of chloride cells into the plasma against a sizeable electrochemical gradient, thereby completing the transepithelial uptake of calcium. Calcium efflux occurs passively through paracellular pathways between chloride cells and adjacent pavement cells or between neighboring pavement cells

Amine and Titanium (IV Chloride, Boron (III Chloride or Zirconium (IV Chloride-Promoted Baylis-Hillman Reactions

Directory of Open Access Journals (Sweden)

Shi-Cong Cui

2001-10-01

Full Text Available The Baylis-Hillman reactions of various aryl aldehydes with methyl vinyl ketone at temperatures below -20oC using Lewis acids such as titanium (IV chloride, boron (III chloride or zirconium (IV chloride in the presence of a catalytic amount of selected amines used as a Lewis bases afford the chlorinated compounds 1 as the major product in very high yields. Acrylonitrile can also undergo the same reaction to give the corresponding chlorinated product in moderate yield. A plausible reaction mechanism is proposed. However, if the reaction was carried out at room temperature (ca. 20oC, then the Z-configuration of the elimination product 3, derived from 1, was formed as the major product.

effect of post-precipitation treatment on the pore-structure stability of sol-gel derived lanthanum zirconate

NARCIS (Netherlands)

Nair, Jalajakumari; Kumar, K.N.P.; Nair, P.; van Ommen, J.G.; Ross, J.R.H.; Ross, Julian R.H.; Burggraaf, Anthonie J.; Burggraaf, Anthonie

1998-01-01

The importance of post-precipitation treatments (pore-fluid exchange and its removal) on the evolution of the texture of coprecipitated lanthanum zirconate has been investigated. The nature of the pore fluid and the type of fluid-removal (drying) process have shown a profound effect on the aggregate

Chloride Transport in Heterogeneous Formation

Science.gov (United States)

Mukherjee, A.; Holt, R. M.

2017-12-01

The chloride mass balance (CMB) is a commonly-used method for estimating groundwater recharge. Observations of the vertical distribution of pore-water chloride are related to the groundwater infiltration rates (i.e. recharge rates). In CMB method, the chloride distribution is attributed mainly to the assumption of one dimensional piston flow. In many places, however, the vertical distribution of chloride will be influenced by heterogeneity, leading to horizontal movement of infiltrating waters. The impact of heterogeneity will be particularly important when recharge is locally focused. When recharge is focused in an area, horizontal movement of chloride-bearing waters, coupled with upward movement driven by evapotranspiration, may lead to chloride bulges that could be misinterpreted if the CMB method is used to estimate recharge. We numerically simulate chloride transport and evaluate the validity of the CMB method in highly heterogeneous systems. This simulation is conducted for the unsaturated zone of Ogallala, Antlers, and Gatuna (OAG) formations in Andrews County, Texas. A two dimensional finite element model will show the movement of chloride through heterogeneous systems. We expect to see chloride bulges not only close to the surface but also at depths characterized by horizontal or upward movement. A comparative study of focused recharge estimates in this study with available recharge data will be presented.

Angle resolved x-ray photoelectron spectroscopy (ARXPS) analysis of lanthanum oxide for micro-flexography printing

Energy Technology Data Exchange (ETDEWEB)

Hassan, S., E-mail: suhaimihas@uthm.edu.my; Yusof, M. S., E-mail: mdsalleh@uthm.edu.my; Maksud, M. I., E-mail: midris1973@gmail.com [Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Batu Pahat, Johor (Malaysia); Embong, Z., E-mail: zaidi@uthm.edu.my [Faculty of Science, Technology and Human Development, Universiti Tun Hussein Onn Malaysia, 86400 Batu Pahat, Johor (Malaysia)

2016-01-22

Micro-flexography printing was developed in patterning technique from micron to nano scale range to be used for graphic, electronic and bio-medical device on variable substrates. In this work, lanthanum oxide (La{sub 2}O{sub 3}) has been used as a rare earth metal candidate as depositing agent. This metal deposit was embedded on Carbon (C) and Silica (Si) wafer substrate using Magnetron Sputtering technique. The choose of Lanthanum as a target is due to its wide application in producing electronic devices such as thin film battery and printed circuit board. The La{sub 2}O{sub 3} deposited on the surface of Si wafer substrate was then analyzed using Angle Resolve X-Ray Photoelectron Spectroscopy (ARXPS). The position for each synthetic component in the narrow scan of Lanthanum (La) 3d and O 1s are referred to the electron binding energy (eV). The La 3d narrow scan revealed that the oxide species of this particular metal is mainly contributed by La{sub 2}O{sub 3} and La(OH){sub 3}. The information of oxygen species, O{sup 2-} component from O 1s narrow scan indicated that there are four types of species which are contributed from the bulk (O{sup 2−}), two chemisorb component (La{sub 2}O{sub 3}) and La(OH){sub 3} and physisorp component (OH). Here, it is proposed that from the adhesive and surface chemical properties of La, it is suitable as an alternative medium for micro-flexography printing technique in printing multiple fine solid lines at nano scale. Hence, this paper will describe the capability of this particular metal as rare earth metal for use in of micro-flexography printing practice. The review of other parameters contributing to print fine lines will also be described later.

Angle resolved x-ray photoelectron spectroscopy (ARXPS) analysis of lanthanum oxide for micro-flexography printing

Science.gov (United States)

Hassan, S.; Yusof, M. S.; Embong, Z.; Maksud, M. I.

2016-01-01

Micro-flexography printing was developed in patterning technique from micron to nano scale range to be used for graphic, electronic and bio-medical device on variable substrates. In this work, lanthanum oxide (La2O3) has been used as a rare earth metal candidate as depositing agent. This metal deposit was embedded on Carbon (C) and Silica (Si) wafer substrate using Magnetron Sputtering technique. The choose of Lanthanum as a target is due to its wide application in producing electronic devices such as thin film battery and printed circuit board. The La2O3 deposited on the surface of Si wafer substrate was then analyzed using Angle Resolve X-Ray Photoelectron Spectroscopy (ARXPS). The position for each synthetic component in the narrow scan of Lanthanum (La) 3d and O 1s are referred to the electron binding energy (eV). The La 3d narrow scan revealed that the oxide species of this particular metal is mainly contributed by La2O3 and La(OH)3. The information of oxygen species, O2- component from O 1s narrow scan indicated that there are four types of species which are contributed from the bulk (O2-), two chemisorb component (La2O3) and La(OH)3 and physisorp component (OH). Here, it is proposed that from the adhesive and surface chemical properties of La, it is suitable as an alternative medium for micro-flexography printing technique in printing multiple fine solid lines at nano scale. Hence, this paper will describe the capability of this particular metal as rare earth metal for use in of micro-flexography printing practice. The review of other parameters contributing to print fine lines will also be described later.

Electrochemical Chloride extraction using external electrodes?

DEFF Research Database (Denmark)

Ottosen, Lisbeth M.; Pedersen, Anne Juul

2006-01-01

Electrochemical methods for the removal of chloride from concrete have been developed and the methods are primarily designed for situations where corrosion has started due to an increased chloride concentration in the vicinity of the reinforcement. In these methods the reinforcement is used...... as the cathode. However, some unwanted side effects can occur, including alkali-silica reaction and in some cases hydrogen embrittlement. It is also suggested also to use electrochemical chloride extraction in a preventive way in constructions where chloride induced corrosion is likely to be a problem after...... a period of time, i.e. remove the chlorides before the chloride front reaches the reinforcement. If the chlorides are removed from outer few centimetres from the surface, the chloride will not reach the reinforcement and cause damage. By using the electrochemical chloride removal in this preventive way...

Thermoluminescent kinetic parameters of the perovskite, KMgF3, activated with lanthanum

International Nuclear Information System (INIS)

Sepulveda M, F.; Azorin N, J.; Rivera M, T.; Furetta, C.; Sanipoli, C.

2004-01-01

The thermoluminescent curves induced by the beta radiation in the perovskite KMgF 3 were investigated activated with lanthanum. The classic methods were used to determine the kinetic parameters (the kinetic order b, the activation energy E and the frequency of escape intent s) associated with the peaks of the thermoluminescent curve (Tl) in the KMgF 3 activated with lanthanum after the irradiation with beta rays. The method is based on the position of the thermoluminescent peaks, obtained of the temperature change of the peak in the maximum emission caused by the change in the heating rapidity to which the samples were measured. In this work, the samples in form of pellets were re cooked previously at 400 C during one hour before irradiating them with beta particles. The Tl measures were made with a Tl reader system using three different heating rapidities and storing the glow curves. To calculate the depth of the E traps and the frequency factor s, the parameters of the glow curve were determined experimentally of the shame of the glow curve by means of the mensuration of the shame of the maximum temperature of the peak, T M like a function of the heating rapidity. The results indicate that the values of the kinetic parameters are very near among if when they are obtained indistinctly of anyone of the different methods. (Author)

Factors influencing chloride deposition in a coastal hilly area and application to chloride deposition mapping

Directory of Open Access Journals (Sweden)

H. Guan

2010-05-01

Full Text Available Chloride is commonly used as an environmental tracer for studying water flow and solute transport in the environment. It is especially useful for estimating groundwater recharge based on the commonly used chloride mass balance (CMB method. Strong spatial variability in chloride deposition in coastal areas is one difficulty encountered in appropriately applying the method. A high-resolution bulk chloride deposition map in the coastal region is thus needed. The aim of this study is to construct a chloride deposition map in the Mount Lofty Ranges (MLR, a coastal hilly area of approximately 9000 km² spatial extent in South Australia. We examined geographic (related to coastal distance, orographic, and atmospheric factors that may influence chloride deposition, using partial correlation and regression analyses. The results indicate that coastal distance, elevation, as well as terrain aspect and slope, appear to be significant factors controlling chloride deposition in the study area. Coastal distance accounts for 70% of spatial variability in bulk chloride deposition, with elevation, terrain aspect and slope an additional 15%. The results are incorporated into a de-trended residual kriging model (ASOADeK to produce a 1 km×1 km resolution bulk chloride deposition and concentration maps. The average uncertainty of the deposition map is about 20–30% in the western MLR, and 40–50% in the eastern MLR. The maps will form a useful basis for examining catchment chloride balance for the CMB application in the study area.

The origin of current blocking in interfacial conduction in Sr-doped lanthanum gallates

Science.gov (United States)

Park, Hee Jung

2018-02-01

The grain boundary transport of lanthanum gallate has been studied with various doping concentrations, and the origins of blocking on the grain boundary are compared. La1-xSrxGaO3 samples (x = 0.005, 0.01, 0.05 and 0.1) have been prepared and their bulk (grain) and grain boundary resistances been experimentally measured as a function of temperature (T: 200-550 °C) and oxygen partial pressure (Po2) using ac-impedance measurements. In addition, Hebb-Wagner polarization measurements have been conducted to investigate the electrical conductivity of minor charge carriers in the lanthanum gallates. The grain boundary resistance in the low-doped materials (x = 0.005 and 0.01) increases with increasing Po2 while in the highly-doped materials (x = 0.05, 0.1) it hardly depended on Po2. At lower concentrations conduction is mixed and at higher concentrations is found to be predominantly ionic conductivity. The space charge model successfully describes the mixed conduction at the grain boundary at low-doping, but does not explain the predominant ionic conductivity at high-doping. The origin of blocking at high-doping is explained by the crystallographic asymmetry of the grain boundary with respect to the bulk and/or Sr-segregation.

Improved adaptation of test with lanthanum nitrate for the colorimetric estimation of acetate

Energy Technology Data Exchange (ETDEWEB)

Szumilo, T [Akademia Medyczna, Lublin (Poland)

1976-01-01

A colorimetric method for the determination of acetate based on the production of the blue complex between iodine and lanthanum alkaline acetate has been developed. Optimum concentrations of reagents (acetate, lanthanum nitrate, iodine and ammonia) as well as the volume of acetate were selected to achieve best colour intensity. Coloured complex was stabilized by dilution of reagent mixture with water to the final volume convenient for determinaton. Absorbance of the complex can be measured immediately after dilution and any changes can be observed during at least 15 minutes. Elevation of temperature over 60/sup 0/decreases absorbance. The method fulfills the Beer's law in the range 1,5-3,5 ..mu..moles of acetate, precision of the method 2/sup +/ = 3,7%. Apart from acetate - propionate and fluoroacetate complex is 620 nm, propionate complex - at 590 nm. Propionate complex displayed any relationship between concentration and absorbance. Potassium, sodium, lithium and barium acetates give the identical results as acetic acid, whereas zinc and cupric acetates failed to react. Other derivatives tested, e.g. chloroacetate, trichloroacetate, iodoacetate, chloroporpionate and butyrate are unable to form the coloured complexes. Many compounds interfere with the formation of acetate complex, therefore, in material containing impurities acetate can be determined after purificaton by means of described in literature methods.

On the stability of the ternary phases in the La-Co-O system and the nonstoichiometry of lanthanum cobaltate

International Nuclear Information System (INIS)

Seppaenen, Matti

1979-01-01

The crystal structure of La 4 Co 3 O 10 , which is a new ternary phase identified in the present study, was determined by means of X-ray diffraction. It has an orthorhombic symmetry and its space group is most likely Fsub(mmm) (face-centered). On the basis of the thermodynamical studies of the La-Co-O system, the stable ternary phases are LaCoO 3 , La 4 Co 3 O 10 and La 2 CoO 4 . The stability limits of these phases were determined as a function of oxygen activity and temperature, and their molar Gibbs standard formation functions were calculated. Electrons, e', and electron holes, hsup(.), are majority defects in lanthanum cobaltate and their concentrations are exceptionally high and nearly constant in the temperature range 1178 - 1295 K. Under thermodynamically well defined conditions the nonstoichiometry of lanthanum cobaltate was determined as a function of oxygen activity and temperature by coulometric titration. In the oxygen partial pressure and temperature range of the present study the oxygen vacancies were ionic minority defects dependent on the activity of oxygen. Due to the high concentration of electronic defects the oxygen vancancy concentration increases high at low oxygen pressures. Oxygen vacancies behave ideally in lanthanum cobaltate i.e. obey Henry's law when their concentrations are <=0.01. (author)

21 CFR 184.1297 - Ferric chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ferric chloride. 184.1297 Section 184.1297 Food and... Substances Affirmed as GRAS § 184.1297 Ferric chloride. (a) Ferric chloride (iron (III) chloride, FeC13, CAS Reg. No. 7705-08-0) may be prepared from iron and chlorine or from ferric oxide and hydrogen chloride...

Effect of Lanthanum as a Promoter on Fe-Co/SiO2 Catalyst for Fischer-Tropsch Synthesis

Directory of Open Access Journals (Sweden)

Ali Abbasi

2014-03-01

Full Text Available Iron-Cobalt catalyst is well known from both operational and economical aspects for Fischer-Tropsch synthesis. Effort to increase the efficiency of this kind of catalyst is an important research topic. In this work, the effect of lanthanum on characteristic behavior, conversion and selectivity of a Fe-Co/SiO2 Fischer-Tropsch catalyst was studied. The Fe-Co-La/SiO2 Catalysts were prepared using an incipient wetness impregnation method. These catalysts were then characterized by XRF-EDAX, BET and TPR techniques, and their performance were evaluated in a lab-scale reactor at 250ºC, H2/CO = 1.8 of molar ratio, 16 barg pressure and GHSV=600 h-1. TPR analysis showed that the addition of La lowered the reduction temperature of Fe-Co catalyst, and due to a lower temperature, the sintering of the catalyst can be mitigated. Furthermore, from the micro reactor tests (about 4 days, it was found that lanthanum promoted catalyst had higher selectivity toward hydrocarbons, and lower selectivity toward CO2.Received: 8th July 2013; Revised: 18th November 2013; Accepted: 1st December 2013[How to Cite: Abbasi, A., Ghasemi, M., Sadighi, S. (2014. Effect of Lanthanum as a Promoter on Fe-Co/SiO2 Catalyst for Fischer-Tropsch Synthesis. Bulletin of Chemical Reaction Engineering & Catalysis, 9 (1: 23-27. (doi:10.9767/bcrec.9.1.5142.23-27][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.9.1.5142.23-27

Lanthanum chromite colloidal processing; Processamento coloidal de cromito de lantanio

Energy Technology Data Exchange (ETDEWEB)

Setz, Luiz Fernando Grespan

2009-07-01

Lanthanum chromite (LaCrO{sub 3}) is currently the most studied material for applications such as solid oxide fuel cell inter connector (HTSOFC). The complexity of microstructures and geometries of HTSOFC devices, require a precise control of processing parameters to get the desired combination of properties and this, the use of techniques involving concentrated ceramic slips conformation are appropriate, therefore, is well controlled, assist in obtaining homogeneous parts, reproductive and complex geometries. Thus, studies involving the surface chemistry, the stability conditions and slips flow behaviour in the forming conditions, provide important elements for processes control in the inter connectors manufacture, where more applied settings have slots and channels for the gases passage. Thus, surface chemistry, stability and rheological behaviour of strontium and cobalt doped LaCrO{sub 3} (La{sub 0.80}Sr{sub 0.20}Cr{sub 0.92}Co{sub 0.08}O{sub 3}) slips prepared with ethanol and water, were studied. The doped lanthanum chromite was produced by combustion synthesis in the IPEN/SP labs. The influence of parameters: p H (water), dispersant concentration, homogenization times and conditions, solid concentration, different ratios binder:plasticizer in the stability and the flow behavior of ceramic suspensions prepared were evaluated. The La{sub 0.80}Sr{sub 0.20}Cr{sub 0.92}Co{sub 0.08}O{sub 3} products obtained by casting aqueous slips in a plaster mould, using alkaline p H and anionic polyelectrolyte and tapes obtained by using ethanol as a dispersant medium, after sintering at 1600 deg C/4h presented theoretical density > 94%, suitable for use as HTSOFC inter connector. (author)

Promising Ni-Fe-LSGMC anode compatible with lanthanum gallate electrolyte

Energy Technology Data Exchange (ETDEWEB)

Wang Shizhong [Department of Chemistry, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen, Fujian 361005 (China); School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0245 (United States)], E-mail: shizwang@sohu.com; He, Qiong [Department of Chemistry, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen, Fujian 361005 (China); Liu Meilin [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0245 (United States)], E-mail: meilin.liu@mse.gatech.edu

2009-06-01

A number of composite materials in the Ni-Fe-LSGMC family have been studied as potential anodes for solid oxide fuel cells (SOFCs) based on strontium, magnesium, and cobalt doped lanthanum gallate electrolyte (LSGMC). The results show that Ni reacts with LSGMC especially under reducing conditions at high temperatures, resulting in high contact resistance, large electrode polarization, and poor performance. The reaction between Ni and LSGMC depends strongly on the composition and pre-sintering temperature of LSGMC, the concentration of iron in the electrode, and the processing and operating temperatures. Under proper conditions, Ni-Fe-LSGMC5 could be a promising high-performance anode with good compatibility with LSGMC5 electrolyte.

Promising Ni-Fe-LSGMC anode compatible with lanthanum gallate electrolyte

International Nuclear Information System (INIS)

Wang Shizhong; He, Qiong; Liu Meilin

2009-01-01

A number of composite materials in the Ni-Fe-LSGMC family have been studied as potential anodes for solid oxide fuel cells (SOFCs) based on strontium, magnesium, and cobalt doped lanthanum gallate electrolyte (LSGMC). The results show that Ni reacts with LSGMC especially under reducing conditions at high temperatures, resulting in high contact resistance, large electrode polarization, and poor performance. The reaction between Ni and LSGMC depends strongly on the composition and pre-sintering temperature of LSGMC, the concentration of iron in the electrode, and the processing and operating temperatures. Under proper conditions, Ni-Fe-LSGMC5 could be a promising high-performance anode with good compatibility with LSGMC5 electrolyte.

The systems lanthanum (cerium, samarium) nitrate-tetramethyl-ammonium nitrate-water

International Nuclear Information System (INIS)

Zhuravlev, E.F.; Khisaeva, D.A.; Semenova, Eh.B.

1984-01-01

The method of cross sections at 25 and 50 deg C has been applied to study solubility in the systems lanthanum nitrate-tetramethyl ammonium nitrate-water (1), cesium (3) nitrate-tetramethyl ammonium nitrate-water (2) and samarium nitrate-tetramethyl ammonium nitrate-water (3). Crystallization fields of congruently dissolving compounds with 1:3 ratio of salt components (in system 1) and 1:2 ratio (in systems 2 and 3) are found in the systems. New solid phases are separated preparatively and subjected to chemical, differential thermal and IR spectroscopic analyses. Compositions of formed compounds are compared with the compositions known for nitrates of other representatives of light lanthanides

Cytotoxicity and genotoxicity of a monazite component: lanthanum effects on the viability and induction of breaks in the DNA of human lymphocytes

International Nuclear Information System (INIS)

Paiva, Amanda Valle de Almeida

2007-01-01

The Monazite is a mineral extracted from open mines. It is constituted by lanthanum element aggregated with cerium, yttrium and thorium [(Ce, La, Y, Th)PO 4 ]. Lanthanum (La) is a rare-earth metal with applications in agriculture, industry and medicine. Since lanthanides and their compounds show a broad spectrum of applications there is an increased risk of incorporation in human. Inhalation of aerosols containing La is the main route of incorporation in workers exposed to several chemical forms of La. Herein, we examined the effect of lanthanum nitrate - La(NO 3 ) 3 in human lymphocytes. JURKAT cells and human peripheral lymphocytes (HPL) were used to evaluate the effect of La(NO 3 ) 3 on viability (apoptosis or necrosis) and DNA strand breaks induction or/and alkali-labile sites (ALS). We demonstrate that La has a cytotoxic and genotoxic effect on both cell lines. The results indicate that necrosis is the pathway by which La(NO 3 ) 3 induces cytotoxicity. The vitamin E is able to diminish DNA strand breaks induced by La(NO 3 ) 3 suggesting that reactive oxygen species (ROS) may be involved in the genotoxic process. (author)

Dynamic electrochemical measurement of chloride ions

NARCIS (Netherlands)

Abbas, Yawar; de Graaf, Derk B.; Olthuis, Wouter; van den Berg, Albert

2016-01-01

This protocol describes the dynamic measurement of chloride ions using the transition time of a silver silver chloride (Ag/AgCl) electrode. Silver silver chloride electrode is used extensively for potentiometric measurement of chloride ions concentration in electrolyte. In this measurement,

Reaction of calcium chloride with alkali metal chlorides in melts

International Nuclear Information System (INIS)

Savin, V.D.; Mikhajlova, N.P.

1984-01-01

Thermochemical characteristics of CaCl 2 reaction with sodium, potassium, rubidium and cesium chlorides in melts at 890 deg C are determined. The values of formation enthalpies of infinitely diluted by CaCl 2 solutions (ΔH) in the chloride row increase from -22 in NaCl to -47 kJ/mol of CaCl 2 in CsCl. With increasing the concentration of calcium chloride in the solution the ΔH values decrease. The regularities of separation from the solution of the CaCl 2 -CsCl system at 890 deg C of the CaCl 2 x CsCl in solid are studied. Formation enthalpies under the given conditions constitutes -70+-3 kJ/mol

Gamma-induced radiation polymerization of kaolin composite for sorption of lanthanum, europium and uranium ions from low-grade monazite leachate

International Nuclear Information System (INIS)

Metwally, S.S.; Hassan, R.S.; El-Masry, E.H.; Borai, E.H.

2018-01-01

Gamma radiation polymerization method was used for the modification of kaolin to produce (poly acrylamide-acrylic acid)-Kaolin (PAM-AA-K). Monazite ore is one of the main resources of uranium and lanthanide elements, therefore, this work focused on sorption of uranium, lanthanum and europium ions from low grade monazite leachate. The removal percent for Eu 3+ , La 3+ and UO 2 2+ are 94.6, 91.6 and 73.4%, respectively. Monolayer capacity of Eu 3+ , La 3+ and UO 2 2+ were found to be 54.64, 45.87 and 37.59 mg/g, respectively. The sorption mechanism of lanthanum and europium ions on PAM-AA-K composite mainly takes place as Ln(OH) 2+ , and for uranium as uranyl ion, UO 2 2+ . (author)

Facile Preparation of Chloride-Conducting Membranes : First Step towards a Room-Temperature Solid-State Chloride-Ion Battery

NARCIS (Netherlands)

Gschwind, Fabienne; Steinle, Dominik; Sandbeck, Daniel; Schmidt, Celine; von Hauff, Elizabeth

2016-01-01

Three types of chloride-conducting membranes based on polyvinyl chloride, commercial gelatin, and polyvinyldifluoride-hexafluoropolymer are introduced in this report. The polymers are mixed with chloride-containing salts, such as tetrabutylammonium chloride, and cast to form membranes. We studied

Analysis of the elements sputtered during the lanthanum implantation in stainless steels

International Nuclear Information System (INIS)

Ager, F.J.; Respaldiza, M.A.; Silva, M.F. da; Redondo, L.M.; Soares, J.C.

1998-01-01

The evidence of the modification of the surface structure of the AISI-304 stainless steel during the implantation of lanthanum makes the analysis of the sputtered elements very interesting. Those sputtered elements are deposited on a carbon sheet placed in front of the steel being implanted, and studied by means of RBS and PIXE, together with the implanted specimens. Besides, the protective effect of the implanted ions during the high temperature oxidation is also studied by those techniques together with XRD and thermogravimetric methods. (orig.)

Vaporization and diffusion studies on the stability of doped lanthanum gallates

Energy Technology Data Exchange (ETDEWEB)

Stanislowski, M.; Singheiser, L.; Hilpert, K. [Research Center Juelich, Institute for Materials and Processes in Energy Systems, IWV-2, 52425 Juelich (Germany); Peck, D.H.; Woo, S.K. [Korea Institute of Energy Research, 71-2 Jang-Dong, Yuseong, 305-343 Daejeon (Korea); Schulz, O.; Martin, M. [RWTH Aachen University, Institute of Physical Chemistry, Landoltweg 2, 52056 Aachen (Germany)

2006-07-15

Vaporization and diffusion determine the stability of doped lanthanum gallates under SOFC operating conditions. Systematic vaporization studies of Ga and other elements were carried out using the vapor transpiration method. It was shown that the Ga vaporization is controlled by diffusion from the bulk to the surface. Diffusion coefficients D{sub Ga} and vaporization coefficients {alpha}{sub Ga} were determined by fitting the measured vaporization data to a vaporization model. Secondary phases formed as a result of the vaporization were detected. The influence of different doping levels of Sr, Mg and Fe on the Ga vaporization was elucidated. Moreover, cation self-diffusion of {sup 139}La, {sup 84}Sr and {sup 25}Mg as well as cation impurity diffusion of {sup 144}Nd, {sup 89}Y and {sup 56}Fe in polycrystalline samples of doped lanthanum gallate were directly determined for the composition La{sub 0.9}Sr{sub 0.1}Ga{sub 0.9}Mg{sub 0.1}O{sub 2.9} as an example, from diffusion profiles determined by SIMS. It was found that diffusion occurs by means of bulk and grain boundaries. The bulk diffusion coefficients are similar for all cations with activation energies which are strongly dependent on temperature. The results are explained by a frozen-in defect structure at low temperatures in the ABO{sub 3} perovskite lattice and by proposing a defect cluster containing cation vacancies in the A and B sublattices, as well as oxygen vacancies. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Study of lanthanum aluminate for cost effective electrolyte material for SOFC

Science.gov (United States)

Verma, O. N.; Shahi, A. K.; Singh, P.

2018-05-01

The perovskite type electrolyte material LaAlO3 (abbreviated LAO) has been prepared by easy processing of auto-combustion synthesis using lanthanum nitrate and aluminium nitrate salts as precursors and citric acid as the fuel. The XRD analysis reveals that as synthesized material exhibits only single phase having rhombohedral structure. The measured density and theoretical density have been deliberated. The temperature dependent electrical conductivity of LAO increases with increasing the temperature which leads to increased mobility of oxide ion. The major contribution of such a significant value of ionic conductivity of LAO can be inferred to grain boundary resistance.

Relaxation features of the Young's modulus and internal friction of lanthanum

International Nuclear Information System (INIS)

Bodryakov, V.Yu.

1993-01-01

E Young module and Q -1 inner friction of polycrystalline lanthanum specimens are studied comprehensively within 4.2-420 K temperature range using bend autovibrations of a specimen represented by a thin rod within ∼ 1-2 kHz frequency range. Three maximums of relaxation nature innner friction are detected under ∼ 380-410, 250-270 and 90-120 K temperatures with 0.29, 0.21 and 0.02 eV activation energies, respectively, on Q -1 (T) curves. Maximums of inner friction are accompanied by peculiarities of E(T) Young module behaviour. 21 refs., 3 figs., 2 tabs

Study of binding properties of lanthanum to wheat roots by INAA

International Nuclear Information System (INIS)

Zhang, Z.Y.; Li, F.L.; Xiao, H.Q.; Chai, Z.F.; Xu, L.; Liu, N.

2004-01-01

Chemical behavior of lanthanum in root tips excized from wheat seedlings growing at both promotional and inhibitory levels of LaCl 3 in culture solutions was investigated by a sequential leaching procedure combined with instrumental neutron activation analysis. The results indicate that most of La exists in non-exchangeable species and the binding of La 3+ to the root tips is extremely stable. The root tips during growing at the inhibitory level of LaCl 3 absorb much more La than those at the promotional level. However, the La proportion in each fraction is similar for both groups. (author)

Electrochemical chloride extraction of a beam polluted by chlorides after 40 years in the sea

OpenAIRE

BOUTEILLER, Véronique; LAPLAUD, André; MALOULA, Aurélie; MORELLE, René Stéphane; DUCHESNE, Béatrice; MORIN, Mathieu

2006-01-01

A beam element, naturally polluted by chlorides after 40 years of a marine tidal exposure, has been treated by electrochemical chloride extraction. The chloride profiles, before and after treatment, show that free chlorides are extrated with an efficiency of 70 % close to the steel, 50 % in the intermediate cover and only 5 % at the concrete surface. From the electrochemical characterizations (before, after, 1, 2 and 17 months after treatment), the steel potential values can, semehow, indicat...

Sorption of sulphur dioxide in calcium chloride and nitrate chloride liquids

International Nuclear Information System (INIS)

Trzepierczynska, I.; Gostomczyk, M.A.

1989-01-01

Flue gas desulphurization via application of suspensions has one inherent disadvantage: fixation of sulphur dioxide is very poor. This should be attributed to the low content of calcium ions which results from the solubility of the sorbing species. The solubility of sparingly soluble salts (CaO, CaCO 3 ) may be increased by decreasing the pH of the solution; yet, there is a serious limitation in this method: the corrosivity of the scrubber. The objective of this paper was to assess the sorbing capacity of two soluble calcium salts, calcium chloride and calcium nitrate, as a function of calcium ion concentration in the range of 20 to 82 kg/m 3 . It has been found that sorbing capacity increases with the increasing calcium ion concentration until the calcium concentration in the calcium chloride solution reaches the level of 60 kg/m 3 which is equivalent to the chloride ion content of ∼ 110 kg/m 3 . Addition of calcium hydroxide to the solutions brings about an increase in the sorbing capacity up to 1.6 kg/m 3 and 2.2 kg/m 3 for calcium chloride and calcium nitrate, respectively, as a result of the increased sorbent alkalinity. The sorption capacity of the solutions is considerably enhanced by supplementing them by acetate ions (2.8 to 13.9 kg/m 3 ). Increase in the sorption capacity of calcium nitrate solutions enriched with calcium acetate was approximately 30% as high as that of the chloride solutions enriched with calcium acetate was approximately 30% as high as that of the chloride solutions supplemented in the same way. (author). 12 refs, 7 refs, 4 tabs

Electron paramagnetic resonance of V4+ in the lanthanum and cerium orthophosphates

International Nuclear Information System (INIS)

Lima, J.C. de.

1983-11-01

The Electron Paramagnetic Resonance (EPR) spectrum of V 4+ was investigated in polycrystalline samples of lanthanum orthophosphate (LaPO 4 ) and cerium orthophosphate (CePO 4 ) doped with 0.2 wt % vanadium pentoxide (V 2 O 5 ). Measurements were performed at room temperature and 9.5 GHz. In LaPO 4 , two non-equivalent axial sites were inferred from the EPR spectra. The most stable of these two sites is probably substitutional. In CePO 4 , a single axial spectrum was observed. It was attributed to V 4+ in substitutional sites. A central, wide line was also seen; it was attributed to ferromagnetic clusters of vanadium ions. Photoacoustic absorption spectra were also recorded for the two compounds. The EPR and photoacoustic absorption data, when analyzed using the molecular orbital theory, show that for both lanthanum orthophosphate and cerium orthophosphate the ground orbital (d sub(x) 2 sub(-y) 2) of the unpainred electron is purely ionic, while the excited orbitals d sub(xy) and d sub(xz,yz) are partly covalent. The degree of covalency is higher for the d sub(xy) orbital. Finally, it should be pointed out that part of the theory used for the interpretation of the EPR and photoacoustic absorption spectra (study of the ligand field splitting of a d orbital in a site of distorted capped antiprism structure) was developed by the author in the present work and is therefore an original contribution. (Author) [pt

21 CFR 173.375 - Cetylpyridinium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Cetylpyridinium chloride. 173.375 Section 173.375... CONSUMPTION Specific Usage Additives § 173.375 Cetylpyridinium chloride. Cetylpyridinium chloride (CAS Reg. No....1666 of this chapter, at a concentration of 1.5 times that of cetylpyridinium chloride. (c) The...

21 CFR 184.1622 - Potassium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Potassium chloride. 184.1622 Section 184.1622 Food... Specific Substances Affirmed as GRAS § 184.1622 Potassium chloride. (a) Potassium chloride (KCl, CAS Reg... levels not to exceed current good manufacturing practice. Potassium chloride may be used in infant...

Temperature dependence of diffusion coefficients of trivalent uranium ions in chloride and chloride-fluoride melts

International Nuclear Information System (INIS)

Komarov, V.E.; Borodina, N.P.

1981-01-01

Diffusion coefficients of U 3+ ions are measured by chronopotentiometric method in chloride 3LiCl-2KCl and in mixed chloride fluoride 3LiCl(LiF)-2KCl melts in the temperature range 633-1235 K. It is shown It is shown that experimental values of diffusion-coefficients are approximated in a direct line in lg D-1/T coordinate in chloride melt in the whole temperature range and in chloride-fluoride melt in the range of 644-1040 K. Experimental values of diffusion coefficients diviate from Arrhenius equation in the direction of large values in chloride-fluoride melt at further increase of temperature up to 1235 K. Possible causes of such a diviation are considered [ru

Effects of Dredging and Lanthanum-Modified Clay on Water Quality Variables in an Enclosure Study in a Hypertrophic Pond

Directory of Open Access Journals (Sweden)

Miquel Lürling Guido Waajen

2017-05-01

Full Text Available An enclosure experiment was conducted between July and September 2009 to compare the effectiveness of a phosphate fixative, the lanthanum-modified bentonite clay Phoslock® (LMB, dredging, and their combination in controlling eutrophication in a hypertrophic urban pond in Heesch, The Netherlands. In total, 25 water quality variables were monitored. Multivariate analysis revealed that the combination LMB-treated and dredged enclosures deviated most from the pond (reference and the controls, and showed the strongest eutrophication reduction. Overall, dredging significantly increased transparency, lowered turbidity, and improved the oxygen conditions in the enclosures compared to non-dredged ones. Nonetheless, one dredged enclosure deviated dramatically from the others, which might reflect methodological issues with dredging. The LMB treatment appeared to be less effective at mitigating eutrophication than dredging, and phosphate concentrations even increased during the experiment in the LMB-treated enclosures. Chemical equilibrium modeling suggested that humic substances could have formed complexes with lanthanum (La from the LMB, rendering it unavailable for intercepting P over the course of the enclosure experiment. Residual lanthanum concentrations in combination dredging and LMB treatments exceeded the Dutch standard 10-fold. Total zooplankton abundance, and particularly Cladocera, increased in all enclosures over the course of the experiment. The limited effect of LMB in the enclosure experiment and the violation of the Dutch La standard when combined with dredging disqualify LMB as an intervention agent in the restoration of the pond.

Labelling of the tsetse fly Glossina palpalis palpalis by activable elements

International Nuclear Information System (INIS)

Hamann, H.J.; Iwannek, K.H.

1979-01-01

Tsetse flies of the species Glossina palpalis palpalis Rob. Desv. were subjected to various treatments with an aim of achieving labelling with the activable stable elements dysprosium, europium or lanthanum. The substances were injected as chlorides or nitrates, they were added to the food of the flies or applied externally to pupae or adults by dipping, or by spraying with the solutions. Feeding with the labelling substance was in principle the easiest method to handle a large number of flies. Only lanthanum salts have been tested so far and it was found that they were excreted relatively fast. They gave detectable labelling for 4 days after application only. The spraying of adults with lanthanum-containing aerosols was a technique which could be used on a mass-production scale. A fairly homogeneous degree of labelling was achieved, which was so high that during mating a clearly measurable amount of lanthanum was transferred from the labelled male to the female. (Auth.)

Phosphate binding therapy in dialysis patients: focus on lanthanum carbonate

Directory of Open Access Journals (Sweden)

Ismail A Mohammed

2008-11-01

Full Text Available Ismail A Mohammed, Alastair J HutchisonManchester Institute of Nephrology and Transplantation, Manchester Royal Infirmary, Oxford Road, Manchester, UKAbstract: Hyperphosphatemia is an inevitable consequence of end stage chronic kidney disease and is present in the majority of dialysis patients. Recent observational data has associated hyperphosphatemia with increased cardiovascular mortality among dialysis patients. Dietary restriction of phosphate and current dialysis prescription practices are not enough to maintain serum phosphate levels within the recommended range so that the majority of dialysis patients require oral phosphate binders. Unfortunately, conventional phosphate binders are not reliably effective and are associated with a range of limitations and side effects. Aluminium-containing agents are highly efficient but no longer widely used because of well established and proven toxicity. Calcium based salts are inexpensive, effective and most widely used but there is now concern about their association with hypercalcemia and vascular calcification. Sevelamer hydrochloride is associated with fewer adverse effects, but a large pill burden and high cost are limiting factors to its wider use. In addition, the efficacy of sevelamer as a monotherapy in lowering phosphate to target levels in severe hyperphosphatemia remains debatable. Lanthanum carbonate is a promising new non-aluminium, calcium-free phosphate binder. Preclinical and clinical studies have demonstrated a good safety profile, and it appears well tolerated and effective in reducing phosphate levels in dialysis patients. Its identified adverse events are apparently mild to moderate in severity and mostly GI related. It appears to be effective as a monotherapy, with a reduced pill burden, but like sevelamer, it is significantly more expensive than calcium-based binders. Data on its safety profile over 6 years of treatment are now available.Keywords: hyperphosphatemia, lanthanum

STRUCTURE AND THERMAL STABILITY OF THE BENZO-15-CROWN-5 WITH LANTHANUM (III BROMIDE COMPLEX

Directory of Open Access Journals (Sweden)

Muhammad Idiris Saleh

2010-06-01

Full Text Available The reaction of benzo-15-crown-5 (C14H20O5 ligand with La(NO33.7H2O in the presence of HBr has resulted in the production of an exotic sandwich complex, [LaC28H36Br4O10][3Br]. The crystal system is triclinic with space group P1, a = 12.5834(14 Å, b = 13.5816(16 Å, c = 13.8403(16 Å, a = 70.751(2°, b = 66.773(2° and g = 67.631(2°. The cation comprises of the lanthanum atom coordinated to two crowns via three oxygen atoms from each crown in a η3-sandwich fashion. The two phenyl groups of the crown are brominated. The La-OLigand bond lengths are between 2.857(7 and 2.949(7 Å. The trianion [3Br]3- is linear with Br-Br bond lengths of 2.518(2 and 2.560(2 Å respectively. The molecule is stabilized by intermolecular interactions of the type C-H...Br to form dimers and are arranged parallel to bc face.  Keywords: lanthanum, benzo-15-crown-5, hydrogen bonding, bromination, x-ray structure

On isomorphous substitution of calcium by sodium and lanthanum in synthetic hydroxyapatite

International Nuclear Information System (INIS)

Get'man, E.I.; Kanyuka, Yu.V.; Loboda, S.N.

1998-01-01

Isomorphous substitution of calcium by sodium and lanthanum in synthetic hydroxyapatite Ca 5-2x La x (PO 4 ) 3 OH by x=0-2.5 within the temperature range 1100-800 deg C is studied through the roentgenophase analysis and IR-spectroscopy methods. It is established that singlephase solid solutions are formed in the area of x≥0.4 by a≤0.4 there exist phases with LaPO 4 , LaNa 6 (PO 4 ) 3 structures and unknown phase along with solid solution of the apatite structure

Characterization of phosphate sequestration by a lanthanum modified bentonite clay: A solid-state NMR, EXAFS and PXRD study

DEFF Research Database (Denmark)

Dithmer, Line; Lipton, Andrew S; Reitzel, Kasper

2015-01-01

Phosphate (Pi) sequestration by a lanthanum (La) exchanged clay mineral (La-Bentonite), which is extensively used in chemical lake restoration, was investigated on the molecular level using a combination of 31P and 139La solid state NMR spectroscopy (SSNMR), extended X-ray absorption spectroscopy...

21 CFR 184.1138 - Ammonium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium chloride. 184.1138 Section 184.1138 Food... Specific Substances Affirmed as GRAS § 184.1138 Ammonium chloride. (a) Ammonium chloride (NH4Cl, CAS Reg. No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution. The...

21 CFR 184.1426 - Magnesium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Magnesium chloride. 184.1426 Section 184.1426 Food... Specific Substances Affirmed as GRAS § 184.1426 Magnesium chloride. (a) Magnesium chloride (MgC12·6H2O, CAS... hydrochloric acid solution and crystallizing out magnesium chloride hexahydrate. (b) The ingredient meets the...

Equidensitometry: a method for characterising the structure of plasmas. Qualitative characterisation of the lanthanum d.c. arc by equidensitometry of monochromatic arc photographs

International Nuclear Information System (INIS)

Dittrich, K.; Niebergall, K.; Roessler, H.

1976-01-01

A new method has been developed for the experimental characterization of d.c. arc plasmas. The method consists of the combination of the spectral photography of d.c. arc plasmas with a slitless, stigmatic plane-grating spectrograph and the characterization of the photographs with the aid of photographic equidensitometry. The principles of the method are described. The method is used for the investigation of a lanthanum d.c. arc plasma. The qualitative results of the measurements of the axial distributions of the light emission and lanthanum and calcium particle concentrations in the arc are discussed. The limitations and shortcomings of the method are pointed out. (author)

Removal of chloride from MSWI fly ash.

Science.gov (United States)

Chen, Wei-Sheng; Chang, Fang-Chih; Shen, Yun-Hwei; Tsai, Min-Shing; Ko, Chun-Han

2012-10-30

The high levels of alkali chloride and soluble metal salts present in MSWI fly ash is worth noting for their impact on the environment. In addition, the recycling or reuse of fly ash has become an issue because of limited landfill space. The chloride content in fly ash limits its application as basis for construction materials. Water-soluble chlorides such as potassium chloride (KCl), sodium chloride (NaCl), and calcium chloride hydrate (CaCl(2) · 2H(2)O) in fly ash are easily washed away. However, calcium chloride hydroxide (Ca(OH)Cl) might not be easy to leach away at room temperature. The roasting and washing-flushing processes were applied to remove chloride content in this study. Additionally, air and CO(2) were introduced into the washing process to neutralize the hazardous nature of chlorides. In comparison with the water flushing process, the roasting process is more efficient in reducing the process of solid-liquid separation and drying for the reuse of Cl-removed fly ash particles. In several roasting experiments, the removal of chloride content from fly ash at 1050°C for 3h showed the best results (83% chloride removal efficiency). At a solid to liquid ratio of 1:10 the water-flushing process can almost totally remove water-soluble chloride (97% chloride removal efficiency). Analyses of mineralogical change also prove the efficiency of the fly ash roasting and washing mechanisms for chloride removal. Copyright © 2012 Elsevier B.V. All rights reserved.

Potentiometric measurement of polymer-membrane electrodes based on lanthanum

Energy Technology Data Exchange (ETDEWEB)

Saefurohman, Asep, E-mail: saefurohman.asep78@Gmail.com; Buchari,, E-mail: saefurohman.asep78@Gmail.com; Noviandri, Indra, E-mail: saefurohman.asep78@Gmail.com [Department of Chemistry, Bandung Institute of Technology (Indonesia); Syoni [Department of Metallurgy Engineering, Bandung Institute of Technology (Indonesia)

2014-03-24

Quantitative analysis of rare earth elements which are considered as the standard method that has a high accuracy, and detection limits achieved by the order of ppm is inductively coupled plasma atomic emission spectroscopy (ICPAES). But these tools are expensive and valuable analysis of the high cost of implementation. In this study be made and characterized selective electrode for the determination of rare earth ions is potentiometric. Membrane manufacturing techniques studied is based on immersion (liquid impregnated membrane) in PTFE 0.5 pore size. As ionophores to be used tri butyl phosphate (TBP) and bis(2-etylhexyl) hydrogen phosphate. There is no report previously that TBP used as ionophore in polymeric membrane based lanthanum. Some parameters that affect the performance of membrane electrode such as membrane composition, membrane thickness, and types of membrane materials studied in this research. Manufacturing of Ion Selective Electrodes (ISE) Lanthanum (La) by means of impregnation La membrane in TBP in kerosene solution has been done and showed performance for ISE-La. FTIR spectrum results for PTFE 0.5 pore size which impregnated in TBP and PTFE blank showed difference of spectra in the top 1257 cm{sup −1}, 1031 cm{sup −1} and 794.7 cm{sup −1} for P=O stretching and stretching POC from group −OP =O. The result showed shift wave number for P =O stretching of the cluster (−OP=O) in PTFE-TBP mixture that is at the peak of 1230 cm{sup −1} indicated that no interaction bond between hydroxyl group of molecules with molecular clusters fosforil of TBP or R{sub 3}P = O. The membrane had stable responses in pH range between 1 and 9. Good responses were obtained using 10{sup −3} M La(III) internal solution, which produced relatively high potential. ISE-La showed relatively good performances. The electrode had a response time of 29±4.5 second and could be use for 50 days. The linear range was between 10{sup −5} and 10{sup −1} M.

Temperature dependence of magnetoresistance in lanthanum manganite ceramics

International Nuclear Information System (INIS)

Gubkin, M.K.; Zalesskii, A.V.; Perekalina, T.M.

1996-01-01

Magnetoresistivity in the La0.9Na0.1Mn0.9(V,Co)0.1O3 and LaMnO3+δ ceramics was studied. The temperature dependence of magnetoresistance in these specimens was found to differ qualitatively from that in the La0.9Na0.1MnO3 single crystal (the magnetoresistance value remains rather high throughout the measurement range below the Curie temperature), with the maximum values being about the same (20-40% in the field of 20 kOe). Previously published data on magnetization, high frequency magnetic susceptibility, and local fields at the 139La nuclei of the specimens with similar properties attest to their magnetic inhomogeneity. The computation of the conductivity of the nonuniformly ordered lanthanum manganite was performed according to the mean field theory. The calculation results allow one to interpret qualitatively various types of experimental temperature dependences of magnetoresistance

21 CFR 184.1193 - Calcium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium chloride. 184.1193 Section 184.1193 Food... Specific Substances Affirmed as GRAS § 184.1193 Calcium chloride. (a) Calcium chloride (CaCl2·2H2O, CAS Reg. No. 10035-04-8) or anhydrous calcium chloride (CaCl2, CAS Reg. No. 10043-52-4) may be commercially...

Determination of chloride in MOX samples using chloride ion selective electrode

Energy Technology Data Exchange (ETDEWEB)

Govindan, R; Das, D K; Mallik, G K; Sumathi, A; Patil, Sangeeta; Raul, Seema; Bhargava, V K; Kamath, H S [Bhabha Atomic Research Centre, Tarapur (India). Advanced Fuel Fabrication Facility

1997-09-01

The chloride present in the MOX fuel is separated from the matrix by pyrohydrolysis at a temperature of 950 {+-} 50 degC and is then analyzed by chloride ion selective electrode (Cl-ISE). The range covered is 0.4-4 ppm with a precision of better than {+-}5% R.S.D. (author). 4 refs., 1 tab.

Photocatalytic degradation of the Paracetamol drug using Lanthanum doped ZnO nanoparticles and their in-vitro cytotoxicity assay

International Nuclear Information System (INIS)

Shakir, Mohammad; Faraz, Mohd; Sherwani, Mohd Asif; Al-Resayes, Saud I.

2016-01-01

The doping of semiconductor by rare earth metals nanoparticles is an effective way for increasing photocatalytic activity. Zinc oxide and Lanthanum doped Zinc oxide nanoparticles were synthesized by modifying the gel-combustion method. It was found that La can greatly enhance the cytotoxicity and photocatalytic activity of ZnO nanoparticles towards various cell lines and Paracetamol drug. These nanoparticles were characterized by various spectroscopic and other techniques which clearly revealed the presence of lanthanum ions. The absorption edge shifts towards the visible region after doping with La ions. This shift shows that the doping of La ions is favorable for absorbing the visible light. The comparative photocatalytic and cytotoxicity activity revealed that La doped ZnO nanoparticles remarkably enhanced activities as compared to the ZnO nanoparticles. The outcome of these studies offers valuable for planning La doped ZnO nanoparticles having cytotoxicity and photocatalytic activities helpful for the formulation of anticancer product and waste water remediation.

Photocatalytic degradation of the Paracetamol drug using Lanthanum doped ZnO nanoparticles and their in-vitro cytotoxicity assay

Energy Technology Data Exchange (ETDEWEB)

Shakir, Mohammad, E-mail: shakir078@yahoo.com [Department of Chemistry, Aligarh Muslim University, Aligarh 202002 (India); Faraz, Mohd [Department of Chemistry, Aligarh Muslim University, Aligarh 202002 (India); Sherwani, Mohd Asif [Interdisciplinary Biotechnology Unit, Aligarh Muslim University, Aligarh 202002 (India); Al-Resayes, Saud I. [Department of Chemistry, College of Science, King Saud University, Riyadh 11451 (Saudi Arabia)

2016-08-15

The doping of semiconductor by rare earth metals nanoparticles is an effective way for increasing photocatalytic activity. Zinc oxide and Lanthanum doped Zinc oxide nanoparticles were synthesized by modifying the gel-combustion method. It was found that La can greatly enhance the cytotoxicity and photocatalytic activity of ZnO nanoparticles towards various cell lines and Paracetamol drug. These nanoparticles were characterized by various spectroscopic and other techniques which clearly revealed the presence of lanthanum ions. The absorption edge shifts towards the visible region after doping with La ions. This shift shows that the doping of La ions is favorable for absorbing the visible light. The comparative photocatalytic and cytotoxicity activity revealed that La doped ZnO nanoparticles remarkably enhanced activities as compared to the ZnO nanoparticles. The outcome of these studies offers valuable for planning La doped ZnO nanoparticles having cytotoxicity and photocatalytic activities helpful for the formulation of anticancer product and waste water remediation.

The influence of lake water alkalinity and humic substances on particle dispersion and lanthanum desorption from a lanthanum modified bentonite

DEFF Research Database (Denmark)

Reitzel, Kasper; Balslev, Kristiane Astrid; Jensen, Henning S

2017-01-01

A 12 days laboratory study on potential desorption of Lanthanum (La) from a commercial La modified clay (Phoslock) was conducted using lake water from 17 Danish lakes with alkalinities between 0.02 and 3.7 meq L-1and varying concentrations of DOC and humic acids (HA's). A similar study...... was conducted in artificial lake water with alkalinities from 0 to 2.5 meq L-1in order to exclude interference from dissolved HA's. To test if La in solution (FLa) was associated with fine particles, the water samples were filtered sequentially through three filter sizes (1.2 μm, 0.45 μm and 0.2 μm...... at low alkalinities. In addition, this study showed that HA's seem to increase the FLa concentrations in soft water lakes, most likely through complexation of La retained in the Phoslock matrix. In summary, we conclude that elevated La concentrations in lake water after a Phoslock treatment should only...

Pharmacokinetics of vinyl chloride in the rat

International Nuclear Information System (INIS)

Bolt, H.M.; Laib, R.J.; Kappus, H.; Buchter, A.

1977-01-01

When rats are exposed to [ 14 C]vinyl chloride in a closed system, the vinyl chloride present in the atmosphere equilibrates with the animals' organism within 15 min. The course of equilibration could be determined using rats which had been given 6-nitro-1,2,3-benzothiadiazole. This compound completely blocks metabolism of vinyl chloride. The enzymes responsible for metabolism of vinyl chloride are saturated at an atmospheric concentration of vinyl chloride of 250 ppm. Pharmacokinetic analysis shows that no significant cumulation of vinyl chloride or its major metabolites is to be expected on repeated administration of vinyl chlorides. This may be consistent with the theory that a reactive, shortly living metabolite which occurs in low concentration only, may be responsible for the toxic effects of vinyl chloride

Laboratory investigation of electro-chemical chloride extraction from concrete with penetrated chloride

NARCIS (Netherlands)

Polder, R.B.; Hondel, A.W.M. van den

2002-01-01

Chloride extraction of concrete is a short-term electrochemical treatment against corrosion of reinforcing steel. The aim is to remove chloride ions from the concrete cover in order to reinstate passive behaviour. Physically sound concrete is left in place. To make this method more predictable and

Soft X-ray absorption spectra of aqueous salt solutions with highly charged cations in liquid microjets

Energy Technology Data Exchange (ETDEWEB)

Schwartz, Craig P.; Uejio, Janel S.; Duffin, Andrew M.; Drisdell, Walter S.; Smith, Jared D.; Saykally, Richard J.

2010-03-11

X-ray absorption spectra of 1M aqueous solutions of indium (III) chloride, yttrium (III) bromide, lanthanum (III) chloride, tin (IV) chloride and chromium (III) chloride have been measured at the oxygen K-edge. Relatively minor changes are observed in the spectra compared to that of pure water. SnCl{sub 4} and CrCl{sub 3} exhibit a new onset feature which is attributed to formation of hydroxide or other complex molecules in the solution. At higher energy, only relatively minor, but salt-specific changes in the spectra occur. The small magnitude of the observed spectral changes is ascribed to offsetting perturbations by the cations and anions.

Solid-phase extraction (SPE) of Iron using Lanthanum Silicate ion exchange

International Nuclear Information System (INIS)

Kiarostami, V.; Husain, W.

2002-01-01

Solid-phase extraction (SPE) is gaining wide use as an effective and speedy technique which reduces solvent usage, disposal costs and extraction time. The analyte is adsorbed from solution onto a solid adsorbent, which is followed by elution of the analyte with a solvent appropriate for instrumental analysis. However, there is an increasing need for new selective adsorbents to expand the area of this technique. Lanthanum silicate ion exchanger, which shows unusual selectivity elements and in this study, it was employed to develop a SPE method for iron ion. Special experiments such as determination of distribution coefficient for iron ion in different solvent systems have been determined

Cerium-modified Aurivillius-type sodium lanthanum bismuth titanate with enhanced piezoactivities

International Nuclear Information System (INIS)

Wang Chunming; Zhao Liang; Wang Jinfeng; Zheng Limei; Du Juan; Zhao Minglei; Wang Chunlei

2009-01-01

The electrical, piezoelectric and dielectric properties of cerium-modified Aurivillius-type sodium lanthanum bismuth titanate (Na 0.5 La 0.5 Bi 4 Ti 4 O 15 , NLBT) ceramics were investigated. It was found the piezoelectric activities of NLBT ceramics were significantly improved by cerium modification. The piezoelectric coefficient d 33 and Curie temperature T c for the 0.50 wt.% cerium-modified NLBT were found to be 29 pC/N and 573 deg. C, respectively. The reasons for piezoelectric activities improvement by cerium modification were given. A small dielectric abnormity was observed in NLBT ceramics, which can be suppressed by cerium modification.

Enhanced electrocaloric analysis and energy-storage performance of lanthanum modified lead titanate ceramics for potential solid-state refrigeration applications.

Science.gov (United States)

Zhang, Tian-Fu; Huang, Xian-Xiong; Tang, Xin-Gui; Jiang, Yan-Ping; Liu, Qiu-Xiang; Lu, Biao; Lu, Sheng-Guo

2018-01-10

The unique properties and great variety of relaxer ferroelectrics make them highly attractive in energy-storage and solid-state refrigeration technologies. In this work, lanthanum modified lead titanate ceramics are prepared and studied. The giant electrocaloric effect in lanthanum modified lead titanate ceramics is revealed for the first time. Large refrigeration efficiency (27.4) and high adiabatic temperature change (1.67 K) are achieved by indirect analysis. Direct measurements of electrocaloric effect show that reversible adiabatic temperature change is also about 1.67 K, which exceeds many electrocaloric effect values in current direct measured electrocaloric studies. Both theoretical calculated and direct measured electrocaloric effects are in good agreements in high temperatures. Temperature and electric field related energy storage properties are also analyzed, maximum energy-storage density and energy-storage efficiency are about 0.31 J/cm 3 and 91.2%, respectively.

Effect of lead dioxide on the radiation decomposition of hydrated lanthanum nitrate (Preprint No. RES-05)

International Nuclear Information System (INIS)

Patil, S.F.; Bedekar, A.G.; Chiplunkar, N.R.

1988-02-01

The rate of radiation induced decomposition of lanthanum nitrate is found to increase in the presence of lead dioxide as a heterophase impurity. Further, the rate also increases with increasing mole percent of the oxide. The results are explained on the basis of energy transfer processes taking place at the interface between nitrate and oxide crystals. (aut hor). 9 refs

Electronic Conductivity of Doped-Lanthanum Gallate Electrolytes

Science.gov (United States)

Yamaji, Katsuhiko; Xiong, Yue Ping; Kishimoto, Haruo; Horita, Teruhisa; Sakai, Natsuko; Brito, Manuel E.; Yokokawa, Harumi

Electronic conductivity of doped lanthanum gallate electrolytes were determined by using a Hebb-Wagner type polarization cell. Electronic conductivity of cobalt-doped, La0.8Sr0.2Ga0.8Mg0.15Co0.5O3-δ (LSGMC), and non cobalt-doped, La0.8Sr0.2Ga0.8Mg0.2O2.8 (LSGM8282), were measured as a function of oxygen partial pressures. The electronic conductivity of LSGM8282 showed a linear dependence on p(O2)1/4 in the higher p(O2) region, which is attributed to the electronic hole conductivity. The electronic conductivity of LSGMC showed a linear dependence on p(O2)1/6 in the higher p(O2) region. LSGMC has higher electronic conductivity than LSGM, and the conductivity was not clearly changed with temperatures between 600 and 800 °C. In lower p(O2) region, the electronic conductivity data have poor reproducibility and did not show any dependence on p(O2) because of the degradation of the electrolytes in severe reducing atmospheres.

Mechanical properties of lanthanum and yttrium chromites

Energy Technology Data Exchange (ETDEWEB)

Paulik, S.W.; Armstrong, T.R. [Pacific Northwest National Lab., Richland, WA (United States)

1996-12-31

In an operating high-temperature (1000{degrees}C) solid oxide fuel cell (SOFC), the interconnect separates the fuel (P(O{sub 2}){approx}10{sup -16} atm) and the oxidant (P(O2){approx}10{sup 0.2} atm), while being electrically conductive and connecting the cells in series. Such severe atmospheric and thermal demands greatly reduce the number of viable candidate materials. Only two materials, acceptor substituted lanthanum chromite and yttrium chromite, meet these severe requirements. In acceptor substituted chromites (Sr{sup 2+} or Ca{sup 2+} for La{sup 3+}), charge compensation is primarily electronic in oxidizing conditions (through the formation of Cr{sup 4+}). Under reducing conditions, ionic charge compensation becomes significant as the lattice becomes oxygen deficient. The formation of oxygen vacancies is accompanied by the reduction of Cr{sup 4+} ions to Cr{sup 3+} and a resultant lattice expansion. The lattice expansion observed in large chemical potential gradients is not desirable and has been found to result in greatly reduced mechanical strength.

Thermal stability and microstructure of catalytic alumina composite support with lanthanum species

Energy Technology Data Exchange (ETDEWEB)

Ozawa, Masakuni, E-mail: ozawa@numse.nagoya-u.ac.jp; Nishio, Yoshitoyo

2016-09-01

Highlights: • Thermal stability of La-modified γ-Al{sub 2}O{sub 3} with nanometer-scaled structure. • LaAlO{sub 3} particles are dispersed in the aggregated particles of alumina. • Increase of the surface basicity of La modified alumina using CO{sub 2}-TPD. - Abstract: Lanthanum (La) modified γ-alumina composite was examined for application toward thermostable catalytic support at elevated temperature. La added alumina was prepared through an aqueous process using lanthanum (III) nitrate and then characterized by surface area measurement, X-ray powder diffraction (XRD), differential thermal analysis (DTA), scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray photoemission spectroscopy (XPS) and surface desorption of CO{sub 2}. It was found that the properties depended on the La content and heat treatment temperatures. The characterization of the surface, structural and chemical properties of La-Al{sub 2}O{sub 3} showed the existence of a strong interaction between the La species and alumina via formation of new phase and modified surface in Al{sub 2}O{sub 3} samples. LaAlO{sub 3} nanoparticle formed among alumina particles by the solid phase reaction of Al{sub 2}O{sub 3} and La{sub 2}O{sub 3}. The increase of the surface basicity of La modified alumina was demonstrated using CO{sub 2} temperature programmed desorption experiments. The controlled surface interaction between La oxide and alumina provide the unique surface and structural properties of the resulting mixed oxides as catalysts and catalytic supports.

Chloride Ingress in Concrete with Different Age at Time of First Chloride Exposure

DEFF Research Database (Denmark)

Hansen, Esben Østergaard; Iskau, Martin Riis; Hasholt, Marianne Tange

2016-01-01

Concrete structures cast in spring have longer time to hydrate and are therefore denser and more resistant to chloride ingress when first subjected to deicing salts in winter than structures cast in autumn. Consequently, it is expected that a spring casting will have a longer service life....... This hypothesis is investigated in the present study by testing drilled cores from concrete cast in 2012 and 2013 on the Svendborgsund Bridge. The cores are subject to petrographic examination and mapping of chloride profiles. Moreover, chloride migration coefficients have been measured. The study shows...

Producing ammonium chloride from coal or shale

Energy Technology Data Exchange (ETDEWEB)

Christenson, O L

1921-02-25

Process of producing ammonium chloride consists of mixing the substance to be treated with a chloride of an alkali or alkaline earth metal, free silica, water and free hydrochloric acid, heating the mixture until ammonium chloride distills off and collecting the ammonium chloride.

Influence of tellurite on lifetime for samarium doped lanthanum lead borate glass

Science.gov (United States)

Madhu, A.; Eraiah, B.

2018-04-01

Samarium substituted tellurium lanthanum lead borate glass is prepared using melt quenching technique. Luminescence spectra have been recorded upon excitation with 402 nm various transitions from 4G5/2 level, for samarium doped tellurite glasses are studied and also lifetime for all the samples exhibit single exponential behaviour of decay curve. Luminescence spectra of present glasses show quenching effect due to cross-relation channels of samarium ions. The lifetime of glass samples decrease as the tellurite concentration is decreased. So, it evidences that to attain longer lifetime for lasing material one can tune the host by selecting concentration of tellurite.

Performance of planar single cell lanthanum gallate based solid oxide fuel cells

Energy Technology Data Exchange (ETDEWEB)

Maffei, N.; Kuriakose, A.K. [Materials Technology Labs., CANMET, Natural Resources Canada, Ottawa, ON (Canada)

1998-09-01

A novel synthesis of high purity, single phase strontium-magnesium doped lanthanum gallate through a nitrate route is described. The prepared powder is formed into planar monolithic elements by uniaxial pressing followed by isostatic pressing and sintering. XRD analysis of the sintered elements reveal no detectable secondary phases. The performance of the electrolyte in solid oxide fuel cells (SOFC) with three different anode/cathode combinations tested at 700 C with respect to the J-V and power density is reported. The data show that the characteristics of this SOFC are strongly dependent on the particular anode/cathode system chosen. (orig.)

Performance of planar single cell lanthanum gallate based solid oxide fuel cells

Science.gov (United States)

Maffei, N.; Kuriakose, A. K.

A novel synthesis of high purity, single phase strontium-magnesium doped lanthanum gallate through a nitrate route is described. The prepared powder is formed into planar monolithic elements by uniaxial pressing followed by isostatic pressing and sintering. XRD analysis of the sintered elements reveal no detectable secondary phases. The performance of the electrolyte in solid oxide fuel cells (SOFC) with three different anode/cathode combinations tested at 700°C with respect to the J- V and power density is reported. The data show that the characteristics of this SOFC are strongly dependent on the particular anode/cathode system chosen.

Specific heat studies of lanthanum and yttrium sesquicarbides

International Nuclear Information System (INIS)

Cort, B.; Stewart, G.R.; Giorgi, A.L.

1984-01-01

The specific heats of the sesquicarbides LaC/sub 1.35/ and La/sub 0.9/Th/sub 0.1/C/sub 1.6/ (prepared by arc melting) and YC/sub 1.35/ (prepared by a high-pressure technique) have been measured for the first time. No bulk specific heat anomaly appears in either lanthanum compounds, even though (1) inductively measured superconducting transition temperatures are respectively high (11.0 K for LaC/sub 1.35/ and 12.7 K for La/sub 0.9/Th/sub 0.1/C/sub 1.6/) and (2) YC/sub 1.35/ is a bulk superconductor with a T/sub c/ = 10.5 K and Y/sub 0.7/Th/sub 0.3/C/sub 1.58/ (also prepared by high pressure) was previously reported to be a bulk superconductor with a T/sub c/ = 17.1 K. The apparent correlation with preparation technique is discussed

21 CFR 173.400 - Dimethyldialkylammonium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Dimethyldialkylammonium chloride. 173.400 Section... HUMAN CONSUMPTION Specific Usage Additives § 173.400 Dimethyldialkylammonium chloride. Dimethyldialkylammonium chloride may be safely used in food in accordance with the following prescribed conditions: (a...

Microbial reductive dehalogenation of vinyl chloride

Science.gov (United States)

Spormann, Alfred M [Stanford, CA; Muller, Jochen A [Baltimore, MD; Rosner, Bettina M [Berlin, DE; Von Abendroth, Gregory [Nannhein, DE; Meshulam-Simon, Galit [Los Altos, CA; McCarty, Perry L [Stanford, CA

2011-11-22

Compositions and methods are provided that relate to the bioremediation of chlorinated ethenes, particularly the bioremediation of vinyl chloride by Dehalococcoides-like organisms. An isolated strain of bacteria, Dehalococcoides sp. strain VS, that metabolizes vinyl chloride is provided; the genetic sequence of the enzyme responsible for vinyl chloride dehalogenation; methods of assessing the capability of endogenous organisms at an environmental site to metabolize vinyl chloride; and a method of using the strains of the invention for bioremediation.

Cationic copolymerization of cycloaliphatic epoxy resin with an spirobislactone with lanthanum triflate as initiator

International Nuclear Information System (INIS)

Fernandez, Xavier; Ramis, Xavier; Salla, Josep M.

2005-01-01

3,4-Epoxycyclohexylmethyl 3,4-epoxycyclohexane carboxylate (ECH) was cured with different proportions of 1,6-dioxaspiro[4,4]nonane-2,7-dione (s(γ-BL)) using lanthanum triflate as a catalyst. DSC was used to obtain kinetic data associated to the curing process by means of series of non-isothermal experiments. Fourier transform infrared spectroscopy in attenuated total reflection mode (FT-IR/ATR) was used to study the evolution of the epoxide group in order to compare experimental isothermal data with simulated isothermal data. The complexity of the process itself enabled us to compare different procedures for obtaining isoconversional data and to determine the kinetic model that best describes the curing process. An increase in the proportion of s(γ-BL) increases the speed of the curing process. By means of applying isoconversional methods to dynamic experimental data, we observed that an increase in the proportion of s(γ-BL) leads to an overall decrease in the activation energy for the different formulations. Kinetic parameters that were determined using both differential and integral isoconversional procedures were compared. This allowed us to analyze and to discuss the usefulness of different methods in order to obtain a suitable kinetic triplet at each step of the curing of the ECH/s(γ-BL) system using lanthanum triflate as a catalyst

21 CFR 522.1862 - Sterile pralidoxime chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sterile pralidoxime chloride. 522.1862 Section 522....1862 Sterile pralidoxime chloride. (a) Chemical name. 2-Formyl-1-methylpyridinium chloride oxime. (b) Specifications. Sterile pralidoxime chloride is packaged in vials. Each vial contains 1 gram of sterile...

49 CFR 173.322 - Ethyl chloride.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Ethyl chloride. 173.322 Section 173.322 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.322 Ethyl chloride. Ethyl chloride must be...

Preparation of pure anhydrous rare earth chlorides

International Nuclear Information System (INIS)

Bel'kova, N.L.; Slastenova, N.M.; Batyaev, I.M.; Solov'ev, M.A.

1979-01-01

A method has been suggested for obtaining extra-pure anhydrous REE chlorides by chloridizing corresponding oxalates by chlorine in a fluid bed, the chloridizing agents being diluted by an inert gas in a ratio of 2-to-1. The method is applicable to the manufacture of quality chlorides not only of light, but also of heavy REE. Neodymium chloride has an excited life of tau=30 μs, this evidencing the absence of the damping impurities

Crystal field influence on vibration spectra: anhydrous uranyl chloride and dihydroxodiuranyl chloride tetrahydrate

International Nuclear Information System (INIS)

Perrin, Andre; Caillet, Paul

1976-01-01

Vibrational spectra of anhydrous uranyl chloride UO 2 Cl 2 and so called basic uranyl chloride: dihydroxodiuranyl chloride tetrahydrate /UO 2 (OH) 2 UO 2 /Cl 2 (H 2 O) 4 are reported. Factor group method analysis leads for the first time to complete and comprehensive interpretation of their spectra. Two extreme examples of crystal field influence on vibrational spectra are pointed out: for UO 2 Cl 2 , one is unable to explain spectra without taking into account all the elements of primitive crystalline cell, whilst for dihydroxodiuranyl dichloride tetrahydrate the crystal packing has very little effect on vibrational spectra [fr

Chloride Transport in Undersea Concrete Tunnel

Directory of Open Access Journals (Sweden)

Yuanzhu Zhang

2016-01-01

Full Text Available Based on water penetration in unsaturated concrete of underwater tunnel, a diffusion-advection theoretical model of chloride in undersea concrete tunnel was proposed. The basic parameters including porosity, saturated hydraulic conductivity, chloride diffusion coefficient, initial water saturation, and moisture retention function of concrete specimens with two water-binder ratios were determined through lab-scale experiments. The variation of chloride concentration with pressuring time, location, solution concentration, initial saturation, hydraulic pressure, and water-binder ratio was investigated through chloride transport tests under external water pressure. In addition, the change and distribution of chloride concentration of isothermal horizontal flow were numerically analyzed using TOUGH2 software. The results show that chloride transport in unsaturated concrete under external water pressure is a combined effect of diffusion and advection instead of diffusion. Chloride concentration increased with increasing solution concentration for diffusion and increased with an increase in water pressure and a decrease in initial saturation for advection. The dominant driving force converted with time and saturation. When predicting the service life of undersea concrete tunnel, it is suggested that advection is taken into consideration; otherwise the durability tends to be unsafe.

A combinatorial matrix of rare earth chloride mixtures as corrosion inhibitors of AA2024-T3: Optimisation using potentiodynamic polarisation and EIS

International Nuclear Information System (INIS)

Muster, T.H.; Sullivan, H.; Lau, D.; Alexander, D.L.J.; Sherman, N.; Garcia, S.J.; Harvey, T.G.; Markley, T.A.; Hughes, A.E.; Corrigan, P.A.; Glenn, A.M.; White, P.A.; Hardin, S.G.; Mardel, J.; Mol, J.M.C.

2012-01-01

A combinatorial matrix of four rare earth chlorides has been evaluated for the corrosion inhibition of aluminium alloy AA2024-T3 in aqueous solution. Two electrochemical techniques, potentiodynamic polarisation (PP) and electrochemical impedance spectroscopy (EIS), were used to evaluate AA2024-T3 corrosion in 0.1 M NaCl with the addition of 10 −3 M of rare earth chloride mixtures at time periods up to 18 h. PP experiments showed rare earth inhibition of up to 98% within the first hour and thereafter corrosion rates were steadily decreased. The open-circuit potential (OCP) of AA2024-T3 decreased as a function of time for all solutions indicating predominantly cathodic inhibition. However, differing trends in the OCP were observed during PP and EIS experiments and are discussed in terms of likely time-dependent mechanisms. A comparative study of optimisation models indicated the best mixture at 10 −3 M total inhibitor concentration was predicted to be 72% cerium (Ce) and 28% (praseodymium (Pr)/lanthanum (La)) ions. As the amount of Ce is decreased from this level the corrosion inhibition is predicted to decrease also, regardless of what other rare earths (La, Pr and Nd) are added alone or in combination. Individually, La, Pr and Nd show varying levels of corrosion inhibition activity, all of which are inferior to that of Ce. If Ce is absent entirely, then a mixture of approximately 50% Pr and 50% Nd is predicted to be preferred. This is one of the first applications of combinatorial design for the optimisation of corrosion inhibitor mixtures.

21 CFR 582.3845 - Stannous chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Stannous chloride. 582.3845 Section 582.3845 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL....3845 Stannous chloride. (a) Product. Stannous chloride. (b) Tolerance. This substance is generally...

7 CFR 58.434 - Calcium chloride.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Calcium chloride. 58.434 Section 58.434 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Material § 58.434 Calcium chloride. Calcium chloride, when used, shall meet the requirements of the Food...

Fabrication of Sr- and Co-doped lanthanum chromite interconnectors for SOFC

Energy Technology Data Exchange (ETDEWEB)

Setz, L.F.G. [Departamento de Engenharia de Materiais, Universidade Federal de Sao Carlos - DEMa/UFSCar (Brazil); Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN (Brazil); Santacruz, I. [Departamento de Quimica Inorganica, Cristalografia y Mineralogia, Universidad de Malaga, 29071 Malaga (Spain); Colomer, M.T., E-mail: tcolomer@icv.csic.es [Instituto de Ceramica y Vidrio, ICV (CSIC), 28049 Madrid (Spain); Mello-Castanho, S.R.H. [Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN (Brazil); Moreno, R. [Instituto de Ceramica y Vidrio, ICV (CSIC), 28049 Madrid (Spain)

2011-07-15

Graphical abstract: FESEM micrographs of the fresh fracture surfaces for the La{sub 0.80}Sr{sub 0.20}Cr{sub 0.92}Co{sub 0.08}O{sub 3} sintered specimens cast from optimised suspensions with 13.5, 15 and 17.5 vol.% solids loading. Aqueous suspensions were prepared using ammonium polyacrylate (PAA) as dispersant and tetramethylammonium hydroxide (TMAH) to assure a basic pH and providing stabilization. Sintering of the green discs was performed in air at 1600 {sup o}C for 4 h. Highlights: {yields} Optimum casting slips were achieved with 3 wt.% of ammonium polyacrylate and 1 wt.% of tetramethylammonium hydroxide. -- Abstract: Many studies have been performed dealing with the processing conditions of electrodes and electrolytes in solid oxide fuel cells (SOFCs). However, the processing of the interconnector material has received less attention. Lanthanum chromite (LaCrO{sub 3}) is probably the most studied material as SOFCs interconnector. This paper deals with the rheology and casting behaviour of lanthanum chromite based materials to produce interconnectors for SOFCs. A powder with the composition La{sub 0.80}Sr{sub 0.20}Cr{sub 0.92}Co{sub 0.08}O{sub 3} was obtained by combustion synthesis. Aqueous suspensions were prepared to solids loading ranging from 8 to 17.5 vol.%, using ammonium polyacrylate (PAA) as dispersant and tetramethylammonium hydroxide (TMAH) to assure a basic pH and providing stabilization. The influence of the additives concentrations and suspension ball milling time were studied. Suspensions prepared with 24 h ball milling, with 3 wt.% and 1 wt.% of PAA and TMAH, respectively, yielded the best conditions for successful slip casting. Sintering of the green discs was performed in air at 1600 {sup o}C for 4 h leading to relatively dense materials.

21 CFR 582.6193 - Calcium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium chloride. 582.6193 Section 582.6193 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Calcium chloride. (a) Product. Calcium chloride. (b) Conditions of use. This substance is generally...

Apparent molar volumes and compressibilities of lanthanum, gadolinium, lutetium and sodium trifluoromethanesulfonates in N,N-dimethylformamide and N,N-dimethylacetamide

International Nuclear Information System (INIS)

Warmińska, Dorota; Fuchs, Anna; Lundberg, Daniel

2013-01-01

Highlights: ► In DMF the sequence values of both volumes and compressibilities of Ln 3+ ions are: La 3+ ≈ Gd 3+ > Lu 3+ . ► In DMA the ionic volumes of lanthanoid(III) metal ions are, within error limits, identical. ► Obtained results are the consequence of an ion–solvent bonding nature. -- Abstract: The concentration and temperature dependencies of density of lanthanum, gadolinium, lutetium and sodium trifluoromethanesulfonates in N,N-dimethylformamide (DMF) and N,N-dimethylacetamide (DMA) have been determined. From density data the apparent molar volumes and partial molar volumes of the salts at infinite dilution as well as the expansibilities have been evaluated. The apparent molar isentropic compressibilities of lanthanum, gadolinium, lutetium and sodium trifluoromethanesulfonates in DMF and DMA have been calculated from sound velocity data obtained at 298.15 K. The results have been discussed in terms of ion–solvent interactions

Doping and temperature dependence of incommensurate antiferromagnetism in underdoped lanthanum cuprates

International Nuclear Information System (INIS)

Yuan Feng; Feng Shiping; Su Zhaobin; Yu Lu

2001-08-01

The doping, temperature and energy dependence of the dynamical spin structure factors of the underdoped lanthanum cuprates in the normal state is studied within the t-J model using the fermion-spin transformation technique. Incommensurate peaks are found at [(1±δ)π, π], [π, (1±δ)π] at relatively low temperatures with δ linearly increasing with doping at the beginning and then saturating at higher dopings. These peaks broaden and weaken in amplitude with temperature and energy, in good agreement with experiments. The theory also predicts a rotation of these peaks by π/4 at even higher temperatures, being shifted to [(1±δ/√2)π, (1±δ/√2)π]. (author)

Chloride removal from plutonium alloy

International Nuclear Information System (INIS)

Holcomb, H.P.

1983-01-01

SRP is evaluating a program to recover plutonium from a metallic alloy that will contain chloride salt impurities. Removal of chloride to sufficiently low levels to prevent damaging corrosion to canyon equipment is feasible as a head-end step following dissolution. Silver nitrate and mercurous nitrate were each successfully used in laboratory tests to remove chloride from simulated alloy dissolver solution containing plutonium. Levels less than 10 ppM chloride were achieved in the supernates over the precipitated and centrifuged insoluble salts. Also, less than 0.05% loss of plutonium in the +3, +4, or +6 oxidation states was incurred via precipitate carrying. These results provide impetus for further study and development of a plant-scale process to recover plutonium from metal alloy at SRP

A meta-analysis of water quality and aquatic macrophyte responses in 18 lakes treated with lanthanum modified bentonite (PHOSLOCK®)

NARCIS (Netherlands)

Spears, B.M.; Mackay, E.; Yasseri, S.; Gunn, I.D.M.; Waters, K.E.; Andrews, C.; Cole, S.; Ville, de M.; Kelly, M.; Meis, S.; Moore, A.L.; Nurnberg, G.K.; Oosterhout, van Frank; Lurling, M.F.L.L.W.

2016-01-01

Lanthanum (La) modified bentonite is being increasingly used as a geo-engineering tool for the control of phosphorus (P) release from lake bed sediments to overlying waters. However, little is known about its effectiveness in controlling P across a wide range of lake conditions or of its potential

21 CFR 173.255 - Methylene chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methylene chloride. 173.255 Section 173.255 Food... Solvents, Lubricants, Release Agents and Related Substances § 173.255 Methylene chloride. Methylene chloride may be present in food under the following conditions: (a) In spice oleoresins as a residue from...

21 CFR 182.8252 - Choline chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Choline chloride. 182.8252 Section 182.8252 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... chloride. (a) Product. Choline chloride. (b) Conditions of use. This substance is generally recognized as...

21 CFR 582.5446 - Manganese chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Manganese chloride. 582.5446 Section 582.5446 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5446 Manganese chloride. (a) Product. Manganese chloride. (b) Conditions of use. This...

21 CFR 582.5252 - Choline chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Choline chloride. 582.5252 Section 582.5252 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5252 Choline chloride. (a) Product. Choline chloride. (b) Conditions of use. This...

21 CFR 582.5622 - Potassium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Potassium chloride. 582.5622 Section 582.5622 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5622 Potassium chloride. (a) Product. Potassium chloride. (b) Conditions of use. This...

21 CFR 582.1193 - Calcium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium chloride. 582.1193 Section 582.1193 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1193 Calcium chloride. (a) Product. Calcium chloride. (b) Conditions of use. This substance...

Variation in band gap of lanthanum chromate by transition metals doping LaCr0.9A0.1O3 (A:Fe/Co/Ni)

International Nuclear Information System (INIS)

Naseem, Swaleha; Khan, Wasi; Saad, A. A.; Shoeb, M.; Ahmed, Hilal; Naqvi, A. H.; Husain, Shahid

2014-01-01

Transition metal (Fe, Co, Ni) doped lanthanum chromate (LaCrO 3 ) nanoparticles (NPs) were prepared by gel combustion method and calcinated at 800°C. Microstructural studies were carried by XRD and SEM/EDS techniques. The results of structural characterization show the formation of all samples in single phase without any impurity. Optical properties were studied by UV- visible and photoluminescence techniques. The energy band gap was calculated and the variation was observed with the doping of transition metal ions. Photoluminescence spectra show the emission peak maxima for the pure LaCrO 3 at about 315 nm. Influence of Fe, Co, Ni doping was studied and compared with pure lanthanum chromate nanoparticles

Study of the Effect on Ionic Conductivity and Structral Morphology of the SR Doped Lanthanum Gallate Solid Electrolyte

Science.gov (United States)

Sood, Kapil; Singh, K.; Pandey, O. P.

2013-07-01

In the present study, lanthanum gallate and Sr-doped lanthanum gallate samples were prepared by conventional solid state reaction method. The phase conformation has been performed by using X-ray diffraction (XRD) study. The elemental composition has been confirmed using energy dispersive spectroscopy (EDS) analysis. Ac conductivity of the samples has been measured in the frequency range 0.1-106 Hz and from 50-800 °C. The impedance plots among real and complex impedances at particular temperature have been discussed. The behavior shows the effect of bulk and grain boundary effects of the doped sample. The impedance plots with frequency have been analyzed. The plots have been well fitted to equivalent circuit model. The conductivity shows the Arrhenius type of behavior. The activation energy has been calculated from the plots and represents that the conductivity through the material is mainly ionic. The structural morphology of the samples has been investigated using scanning electron microscope (SEM). The micrograph shows that the porosity and grain size both decreases with Sr-doping.

21 CFR 582.5985 - Zinc chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Zinc chloride. 582.5985 Section 582.5985 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS... 1 § 582.5985 Zinc chloride. (a) Product. Zinc chloride. (b) Conditions of use. This substance is...

21 CFR 182.8985 - Zinc chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Zinc chloride. 182.8985 Section 182.8985 Food and... CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Nutrients § 182.8985 Zinc chloride. (a) Product. Zinc chloride. (b) Conditions of use. This substance is generally recognized as safe when used in...

21 CFR 172.180 - Stannous chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Stannous chloride. 172.180 Section 172.180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Preservatives § 172.180 Stannous chloride. The food additive stannous chloride may be safely used for color...

Synthesis of Ni nanoparticles in lanthanum chromite ceramic matrix

International Nuclear Information System (INIS)

Tinti, Victor Buratto; Florio, Daniel Zanetti de; Fonseca, Fabio Coral

2016-01-01

Full text: Lanthanum chromite is a well-known interconnector for solid oxide fuel cells. It presents electronic conductivity at high temperatures. Moreover it is very stable in oxidizing and reducing atmospheres. Due to its high stability this material is a promising matrix to produce and stabilize nanoparticles by exothermal reaction. The objective of the present work is to synthesize and stabilize nickel nanoparticles in a stable ceramic matrix. Compounds of (La 1-x Sr x ) a (Cr 1-y Ni y )O 3 (x and y = 0, 0.1, and 0.2; a = 1, and 0.8) were synthesized by Pechini method. The powders were heat treated in air at 1300 °C and 1600°C in attempt to solubilise NiO in the matrix. Then the samples were exposed to a reducing treatment in H 2(g) flux at 900°C per 8 hours. XRD measurements were made using a D8 Focus, Bruker AXS. The data was acquired in a range of 2θ from 20° to 90°, with a step of 0,02° per second. Magnetic properties were investigated utilizing a SQUIDVSM from Quantum Design. Magnetic moment at constant magnetic field (100 Oe and 1000 Oe) was measured in a range of 2K to 300K. Analyses with variable magnetic field were performed at 2K, 196K and 390K in a rage from -5 up to 5 T. Samples were observed using TEM technique. The XRD results showed that the stoichiometric samples achieved desiderate phase. Compounds without Sr and non-stoichiometric lanthanum site showed an incomplete nickel solid solution. The addition of 10% of Sr decreases the Neel temperature from 289 K to 285K. Ni doping created a stronger effect, lowering the temperature down to 267 K , in the sample with 10% of dopant. After reduction is possible to observe peaks of Ni in the XRD, indicating that nickel was exoluted form the matrix. Images of TEM confirm the presence of nanoparticles with an approximate diameter of 3 nm. The reducing treatment increased the magnetic response. (author)

High concentrations of cadmium, cerium and lanthanum in indoor air due to environmental tobacco smoke

International Nuclear Information System (INIS)

Böhlandt, Antje; Schierl, Rudolf; Diemer, Juergen; Koch, Christoph; Bolte, Gabriele; Kiranoglu, Mandy; Fromme, Hermann; Nowak, Dennis

2012-01-01

Background: Environmental tobacco smoke (ETS) is one of the most important sources for indoor air pollution and a substantial threat to human health, but data on the concentrations of the trace metals cerium (Ce) and lanthanum (La) in context with ETS exposure are scarce. Therefore the aim of our study was to quantify Ce and La concentrations in indoor air with high ETS load. Methods: In two subsequent investigations Ce, La and cadmium (Cd) in 3 smokers' (11 samples) and 7 non-smokers' (28 samples) households as well as in 28 hospitality venues in Southern Germany were analysed. Active sampling of indoor air was conducted continuously for seven days in every season in the smokers' and non-smokers' residences, and for 4 h during the main visiting hours in the hospitality venues (restaurants, pubs, and discotheques). Results: In terms of residences median levels of Cd were 0.1 ng/m 3 for non-smokers' and 0.8 ng/m 3 for smokers' households. Median concentrations of Ce were 0.4 ng/m 3 and 9.6 ng/m 3 , and median concentrations of La were 0.2 ng/m 3 and 5.9 ng/m 3 for non-smokers' and for smokers' households, respectively. In the different types of hospitality venues median levels ranged from 2.6 to 9.7 ng/m 3 for Cd, from 18.5 to 50.0 ng/m 3 for Ce and from 10.6 to 23.0 ng/m 3 for La with highest median levels in discotheques. Conclusions: The high concentrations of Ce and La found in ETS enriched indoor air of smokers' households and hospitality venues are an important finding as Ce and La are associated with adverse health effects and data on this issue are scarce. Further research on their toxicological, human and public health consequences is urgently required. - Highlights: ► We quantified cer, lanthanum and cadmium concentrations in indoor air. ► Cer and lanthanum concentrations were high in tobacco smoke enriched locations. ► Both elements can be considered as good markers for indoor air quality.

Accomplishment of highly porous-lithium lanthanum titanate through microwave treatment

Energy Technology Data Exchange (ETDEWEB)

Lakshmi, D.; Nalini, B., E-mail: jyothsnalalin99@gmail.com [Department of Physics, Avinashilingam University for Women, Coimbatore, Tamilnadu (India); Abhilash, K. P.; Selvin, P. Christopher [Department of Physics, NGM college for arts and science, Pollachi, Tamilnadu (India)

2016-05-23

Perovskite structured (ABO{sub 3}) lithium lanthanum titanate (LLTO) is a successful electrolyte reported by several scientists in the recent past. It is believed that intercalation and de-intercalation of Li ions inside solid electrolyte can be improved by increasing the porosity of the material. Hence in this research work, an attempt is made to increase the porosity of the LLTO electrolyte by rapid-microwave synthesis route. The microwave prepared LLTO is compared with the sol-gel synthesized LLTO. The prepared samples are analyzed with XRD, SEM, PL and cyclic Voltammetry studies. Morphological analysis proves that microwave synthesized LLTO contains much pores compared to the Sol-gel LLTO. A remarkable difference in its electrochemical property is also demonstrated and analysed with cyclic voltammetric studies and the results are presented.

Salt, chloride, bleach, and innate host defense

Science.gov (United States)

Wang, Guoshun; Nauseef, William M.

2015-01-01

Salt provides 2 life-essential elements: sodium and chlorine. Chloride, the ionic form of chlorine, derived exclusively from dietary absorption and constituting the most abundant anion in the human body, plays critical roles in many vital physiologic functions, from fluid retention and secretion to osmotic maintenance and pH balance. However, an often overlooked role of chloride is its function in innate host defense against infection. Chloride serves as a substrate for the generation of the potent microbicide chlorine bleach by stimulated neutrophils and also contributes to regulation of ionic homeostasis for optimal antimicrobial activity within phagosomes. An inadequate supply of chloride to phagocytes and their phagosomes, such as in CF disease and other chloride channel disorders, severely compromises host defense against infection. We provide an overview of the roles that chloride plays in normal innate immunity, highlighting specific links between defective chloride channel function and failures in host defense. PMID:26048979

Salt, chloride, bleach, and innate host defense.

Science.gov (United States)

Wang, Guoshun; Nauseef, William M

2015-08-01

Salt provides 2 life-essential elements: sodium and chlorine. Chloride, the ionic form of chlorine, derived exclusively from dietary absorption and constituting the most abundant anion in the human body, plays critical roles in many vital physiologic functions, from fluid retention and secretion to osmotic maintenance and pH balance. However, an often overlooked role of chloride is its function in innate host defense against infection. Chloride serves as a substrate for the generation of the potent microbicide chlorine bleach by stimulated neutrophils and also contributes to regulation of ionic homeostasis for optimal antimicrobial activity within phagosomes. An inadequate supply of chloride to phagocytes and their phagosomes, such as in CF disease and other chloride channel disorders, severely compromises host defense against infection. We provide an overview of the roles that chloride plays in normal innate immunity, highlighting specific links between defective chloride channel function and failures in host defense. © Society for Leukocyte Biology.

Vaporization study on lanthanum-neodymium alloys by mass-spectrometry

International Nuclear Information System (INIS)

Shoji, Y.; Matsui, T.

1999-01-01

Partial vapor pressure of Nd(g) over La x Nd 1-x alloys (x = 0.10, 0.20, 0.30, 0.40, 0.50, 0.60, 0.70, 0.80 and 0.90) was measured with a time-of-flight mass-spectrometer equipped with a tungsten Knudsen cell over the temperature range of 1474-1767 K. Thermodynamic activity of neodymium in the liquid alloys was determined by comparing the partial vapor pressure of Nd(g) over the alloys with that over the pure metal. The thermodynamic activity of lanthanum in the alloys was calculated from that of neodymium obtained experimentally in this study by graphic integration using the Gibbs-Duhem equation. Both activities for each element, thus obtained, showed positive deviations from Raoult's law over the entire compositional range. Thermodynamic quantities such as Gibbs free energy of formation, excess enthalpy etc. were also calculated from the thermodynamic activities. (orig.)

Ethanol Electrooxidation on Pt with Lanthanum Oxide as Cocatalyst in a DAFC

Directory of Open Access Journals (Sweden)

T. A. B. Santoro

2012-01-01

Full Text Available Electrocatalytic activity toward ethanol electrooxidation of Pt particles in PtLa/C catalysts with different Pt : La ratios has been studied with different electrochemical and spectroscopic techniques, and the results were compared to those of Pt/C catalyst. Significant enhancement in the electrocatalytic activity has been achieved by depositing the Pt particles with lanthanum oxides/hydroxides using an alcohol reduction method. Compared to Pt/C catalyst, PtLa/C materials exhibit a lower onset potential and a higher electron-transfer rate constant for the investigated reaction. These studies illustrate the possibility of utilizing Pt/C with La oxides/hidroxides as electrocatalyst for direct alcohol fuel cells (DAFCs.

21 CFR 184.1446 - Manganese chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Manganese chloride. 184.1446 Section 184.1446 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Specific Substances Affirmed as GRAS § 184.1446 Manganese chloride. (a) Manganese chloride (MnCl2·4H2O, CAS...

Optical and photoemission studies of lanthanum hydrides

International Nuclear Information System (INIS)

Peterman, D.J.; Peterson, D.T.; Weaver, J.H.

1980-01-01

The results of optical absorptivity and photoemission measurements on lanthanum hydrides, LaH/sub x/ (1.98 less than or equal to x less than or equal to 2.89) are reported. The low energy (hν less than or equal to 0.5 eV) optical features in LaH/sub x/ are attributed to the filling of octahedral sites. Higher energy interband absorption involves states within the d-band complex, analogous to other dihydrides. As x increases above 2.0, the optical features change rapidly due to the increase in the number of occupied octahedral sites. Various band structure studies suggest that LaH 3 might be a semiconductor. Photoemission results show that as x increases, the d-derived states at E/sub F/ are drawn down and that for LaH 2 89 only very weak valence band emission is observed. The hydrogen-derived bonding bands are shown centered approx. 5 eV below E/sub F/. Observed chemical shifts in the La 5p/sub 1/2 3/2/ cores are discussed for 1.98 less than or equal to x less than or equal to 2.89

Method for preparation of melts of alkali metal chlorides with highly volatile polyvalent metal chlorides

International Nuclear Information System (INIS)

Salyulev, A.B.; Kudyakov, V.Ya.

1990-01-01

A method for production of alkali metal (Cs, Rb, K) chloride melts with highly volatile polyvalent metal chlorides is suggested. The method consists, in saturation of alkali metal chlorides, preheated to the melting point, by volatile component vapours (titanium tetrachloride, molybdenum or tantalum pentachloride) in proportion, corresponding to the composition reguired. The saturation is realized in an evacuated vessel with two heating areas for 1-1.5 h. After gradual levelling of temperature in both areas the product is rapidly cooled. 1 fig.; 1 tab

Determination of Chloride Content in Cementitious Materials : From Fundamental Aspects to Application of Ag/AgCl Chloride Sensors

NARCIS (Netherlands)

Pargar, F.; Koleva, D.A.; van Breugel, K.

2017-01-01

This paper reports on the advantages and drawbacks of available test methods for the determination of chloride content in cementitious materials in general, and the application of Ag/AgCl chloride sensors in particular. The main factors that affect the reliability of a chloride sensor are presented.

Size effects of polycrystalline lanthanum modified Bi4Ti3O12 thin films

International Nuclear Information System (INIS)

Simoes, A.Z.; Riccardi, C.S.; Cavalcante, L.S.; Gonzalez, A.H.M.; Longo, E.; Varela, J.A.

2008-01-01

The film thickness dependence on the ferroelectric properties of lanthanum modified bismuth titanate Bi 3.25 La 0.75 Ti 3 O 12 was investigated. Films with thicknesses ranging from 230 to 404 nm were grown on platinum-coated silicon substrates by the polymeric precursor method. The internal strain is strongly influenced by the film thickness. The morphology of the film changes as the number of layers increases indicating a thickness dependent grain size. The leakage current, remanent polarization and drive voltage were also affected by the film thickness

The lanthanum(III molybdate(VI La4Mo7O27

Directory of Open Access Journals (Sweden)

Petra Becker

2009-08-01

Full Text Available Crystals of the orthorhombic phase La4Mo7O27 (lanthanum molybdenum oxide were obtained from a non-stoichiometric melt in the pseudo-ternary system La2O3–MoO3–B2O3. In the crystal structure, distorted square-antiprismatic [LaO8] and monocapped square-antiprismatic [LaO9] polyhedra are connected via common edges and faces into chains along [010]. These chains are arranged in layers that alternate with layers of [MoO4] and [MoO5] polyhedra parallel to (001. In the molybdate layers, a distorted [MoO5] trigonal bipyramid is axially connected to two [MoO4] tetrahedra, forming a [Mo3O11] unit.

Micellar solubilization in strongly interacting binary surfactant systems. [Binary surfactant systems of: dodecyltrimethylammonium chloride + sodium dodecyl sulfate; benzyldimethyltetradecylammonium chloride + tetradecyltrimethylammonium chloride

Energy Technology Data Exchange (ETDEWEB)

Treiner, C. (Universite Pierre et Marie Curie, Paris (France)); Nortz, M.; Vaution, C. (Faculte de Pharmacie de Paris-sud, Chatenay-Malabry (France))

1990-07-01

The apparent partition coefficient P of barbituric acids between micelles and water has been determined in mixed binary surfactant solutions from solubility measurements in the whole micellar composition range. The binary systems chosen ranged from the strongly interacting system dodecyltrimethylammonium chloride + sodium dodecyl sulfate to weakly interacting systems such as benzyldimethyltetradecylammonium chloride + tetradecyltrimethyammonium chloride. In all cases studied, mixed micelle formation is unfavorable to micellar solubilization. A correlation is found between the unlike surfactants interaction energy, as measured by the regular solution parameter {beta} and the solute partition coefficient change upon surfactant mixing. By use of literature data on micellar solubilization in binary surfactant solutions, it is shown that the change of P for solutes which are solubilized by surface adsorption is generally governed by the sign and amplitude of the interaction parameter {beta}.

Evaluation and comparison of two complexometric titration methods for determining of lanthanum in cloridric solutions

International Nuclear Information System (INIS)

Menezes, M.F.; Santos, R.L.C. dos; Goes, M.A.C. de

1994-01-01

The fast determination of total rare earth concentration in aqueous solutions is based on titrimetric methods using EDTA as complexing agent. This paper evaluates two among several others titrimetric methods used in the determination of lanthanum in hydrochloric acid solutions, using xylenol orange and a mixture of methyl orange and xylenol orange as indicators. The applied statistical evaluation allowed the determination of the stability, accuracy and adequacy of these methods on a given technical specification. (author). 12 refs., 03 tabs., 01 fig

Stepwise hydrochloric acid extraction of monazite hydroxides for the recovery of cerium lean rare earths, cerium, uranium and thorium

International Nuclear Information System (INIS)

Swaminathan, T.V.; Nair, V.R.; John, C.V.

1988-01-01

Monazite sand is normally processed by the caustic soda route to produce mixed rare earth chloride, thorium hydroxide and trisodium phosphate. Bulk of the mixed rare earth chloride is used for the preparation of FC catalysts. Recently some of the catalyst producers have shown preference to cerium depleted (lanthanum enriched) rare earth chloride rather than the natural rare earth chloride obtained from monazite. Therefore, a process for producing cerium depleted rare earth chloride, cerium, thorium and uranium from rare earth + thorium hydroxide obtained by treating monazite, based on stepwise hydrochloric acid extraction, was developed in the authors laboratory. The process involves drying of the mixed rare earth-thorium hydroxide cake obtained by monazite-caustic soda process followed by stepwise extraction of the dried cake with hydrochloric acid under specified conditions

Thallium-201 chloride dynamic analysis using thallium-201 chloride and sodium iodide-131 thyroid subtraction scintigraphy

Energy Technology Data Exchange (ETDEWEB)

Morimoto, Setsuo; Hiraki, Yoshio; Togami, Izumi [Okayama Univ. (Japan). School of Medicine

1984-10-01

The mechanism of /sup 201/Tl chloride accumulation is unclear in thyroid gland and thyroid tumor. This report examines 108 patients that received thyroid scintigraphy examinations with both /sup 201/Tl chloride and sodium /sup 131/I. The patients were diagnosed clinically and histologically whenever possible. The ROI were obtained by subtraction imaging with both isotopes and by subtraction positive and negative areas of imaging. Dynamic curves were obtained for /sup 201/Tl chloride per square unit of each ROI. The dynamic curve in the radioiodide-accumulated area was examined. The data indicate that the clearance rate of /sup 201/Tl chloride (T/sub 15/) was correlated with the sodium /sup 131/I uptake rate at 24 h (r=0.70).

Modified chloride diffusion model for concrete under the coupling effect of mechanical load and chloride salt environment

Science.gov (United States)

Lei, Mingfeng; Lin, Dayong; Liu, Jianwen; Shi, Chenghua; Ma, Jianjun; Yang, Weichao; Yu, Xiaoniu

2018-03-01

For the purpose of investigating lining concrete durability, this study derives a modified chloride diffusion model for concrete based on the odd continuation of boundary conditions and Fourier transform. In order to achieve this, the linear stress distribution on a sectional structure is considered, detailed procedures and methods are presented for model verification and parametric analysis. Simulation results show that the chloride diffusion model can reflect the effects of linear stress distribution of the sectional structure on the chloride diffusivity with reliable accuracy. Along with the natural environmental characteristics of practical engineering structures, reference value ranges of model parameters are provided. Furthermore, a chloride diffusion model is extended for the consideration of multi-factor coupling of linear stress distribution, chloride concentration and diffusion time. Comparison between model simulation and typical current research results shows that the presented model can produce better considerations with a greater universality.

Sintering and electrical properties of strontium-doped lanthanum manganite

Energy Technology Data Exchange (ETDEWEB)

Tarrago, Diego Pereira; Sousa, Vania Caldas de [Universidade Federal do Rio Grande do Sul (LABIOMAT/PPGEM/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia de Minas, Metalurgica e de Materiais. Lab. de Biomateriais], Email: dptarrago@gmail.com; Moreno Buriel, Berta; Chinarro Martini, Eva; Jurado Egea, Jose Ramon [Consejo Superior de Investigaciones Cientificas (ICV/CSIC), Madrid (Spain). Inst. de Ceramica y Vidrio; Malfatti, Celia de Fraga [Universidade Federal do Rio Grande do Sul (LAPEC/PPGEM/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia de Minas, Metalurgica e de Materiais. Lab. de Pesquisa em Corrosao

2010-07-01

Lanthanum strontium manganites (LSM) are potential materials for cathode applications in solid oxide fuel cells (SOFC) due to their good catalytic activity, chemical stability and compatibility with electrolyte materials in high temperatures. The sinterability of single phase La{sub 1-x}Sr{sub x}Mn{sub O3} (x=0.18) perovskite powders and the electrical properties of the resulting samples are analyzed in this study. Using a heating microscope, the powders were pressed and sintered at different pressures and temperatures, resulting in an open porosity of 33.36% when compacted at 125 MPa and sintered at 1200 degree C. Top and cross-section s canning electron microscopy (SEM) micrographs revealed interconnected pores in the sintered body and, hence, a suitable microstructure for the application. The activation energy for conductance was 0.04 eV and the tested LSM bulk started to exhibit adequate electrical properties at about 500 degree C. (author)

Enthalpic interactions of N-glycylglycine with xylitol in aqueous sodium chloride and potassium chloride solutions at T = 298.15 K

International Nuclear Information System (INIS)

Liu Min; Wang Lili; Zhu Lanying; Li Hui; Sun Dezhi; Di Youying; Li Linwei

2010-01-01

The mixing enthalpies of N-glycylglycine with xylitol and their respective enthalpies of dilution in aqueous sodium chloride and potassium chloride solutions have been determined by using flow-mix isothermal microcalorimetry at the temperature of 298.15 K. These experimental results have been used to determine the heterotactic enthalpic interaction coefficients (h xy , h xxy , and h xyy ) according to the McMillan-Mayer theory. It has been found that the heterotactic enthalpic pairwise interaction coefficients h xy between N-glycylglycine and xylitol in aqueous sodium chloride and potassium chloride solutions are negative and become less negative with an increase in the molality of sodium chloride or potassium chloride. The results are discussed in terms of solute-solute and solute-solvent interactions.

Enthalpic interactions of N-glycylglycine with xylitol in aqueous sodium chloride and potassium chloride solutions at T = 298.15 K

Energy Technology Data Exchange (ETDEWEB)

Liu Min, E-mail: panpanliumin@163.co [College of Chemistry and Chemical Engineering, Liao Cheng University, Liaocheng, Shandong 252059 (China); Wang Lili [College of Chemistry and Chemical Engineering, Liao Cheng University, Liaocheng, Shandong 252059 (China); Zhu Lanying [College of Life Science and Bioengineering, Liao Cheng University, Liaocheng, Shandong 252059 (China); Li Hui; Sun Dezhi; Di Youying; Li Linwei [College of Chemistry and Chemical Engineering, Liao Cheng University, Liaocheng, Shandong 252059 (China)

2010-07-15

The mixing enthalpies of N-glycylglycine with xylitol and their respective enthalpies of dilution in aqueous sodium chloride and potassium chloride solutions have been determined by using flow-mix isothermal microcalorimetry at the temperature of 298.15 K. These experimental results have been used to determine the heterotactic enthalpic interaction coefficients (h{sub xy}, h{sub xxy}, and h{sub xyy}) according to the McMillan-Mayer theory. It has been found that the heterotactic enthalpic pairwise interaction coefficients h{sub xy} between N-glycylglycine and xylitol in aqueous sodium chloride and potassium chloride solutions are negative and become less negative with an increase in the molality of sodium chloride or potassium chloride. The results are discussed in terms of solute-solute and solute-solvent interactions.

Renal abnormalities in congenital chloride diarrhea

International Nuclear Information System (INIS)

Al-Hamad, Nadia M.; Al-Eisa, Amal A.

2004-01-01

Congenital chloride diarrhea CLD is a rare autosomal recessive disorder caused by a defect in the chloride/ bicarbonate exchange in the ileum and colon. It is characterized by watery diarrhea, abdominal distension, hypochloremic hypokalemic metabolic alkalosis with high fecal content of chloride >90 mmol/l. We report 3 patients with CLD associated with various renal abnormalities including chronic renal failure secondary to renal hypoplasia, nephrocalcinosis and congenital nephrotic syndrome. (author)

Study on the chloride migration coefficient obtained following different Rapid Chloride Migration (RCM) test guidelines

NARCIS (Netherlands)

Spiesz, P.R.; Brouwers, H.J.H.; Uzoegbo, H.C.; Schmidt, W.

2013-01-01

This work presents the differences in the available Rapid Chloride Migration (RCM) test guidelines, and their influence on the values of the chloride migration coefficients DRCM, obtained following these guidelines. It is shown that the differences between the guidelines are significant and concern

Mapping the spatial distribution of chloride deposition across Australia

Science.gov (United States)

Davies, P. J.; Crosbie, R. S.

2018-06-01

The high solubility and conservative behaviour of chloride make it ideal for use as an environmental tracer of water and salt movement through the hydrologic cycle. For such use the spatial distribution of chloride deposition in rainfall at a suitable scale must be known. A number of authors have used point data acquired from field studies of chloride deposition around Australia to construct relationships to characterise chloride deposition as a function of distance from the coast; these relationships have allowed chloride deposition to be interpolated in different regions around Australia. In this paper we took this a step further and developed a chloride deposition map for all of Australia which includes a quantification of uncertainty. A previously developed four parameter model of chloride deposition as a function of distance from the coast for Australia was used as the basis for producing a continental scale chloride deposition map. Each of the four model parameters were made spatially variable by creating parameter surfaces that were interpolated using a pilot point regularisation approach within a parameter estimation software. The observations of chloride deposition were drawn from a literature review that identified 291 point measurements of chloride deposition over a period of 80 years spread unevenly across all Australian States and Territories. A best estimate chloride deposition map was developed from the resulting surfaces on a 0.05 degree grid. The uncertainty in the chloride deposition map was quantified as the 5th and 95th percentile of 1000 calibrated models produced via Null Space Monte Carlo analysis and the spatial variability of chloride deposition across the continent was consistent with landscape morphology. The temporal variability in chloride deposition on a decadal scale was investigated in the Murray-Darling Basin, this highlighted the need for long-term monitoring of chloride deposition if the uncertainty of the continental scale map is

Chloride channels as tools for developing selective insecticides.

Science.gov (United States)

Bloomquist, Jeffrey R

2003-12-01

Ligand-gated chloride channels underlie inhibition in excitable membranes and are proven target sites for insecticides. The gamma-aminobutyric acid (GABA(1)) receptor/chloride ionophore complex is the primary site of action for a number of currently used insecticides, such as lindane, endosulfan, and fipronil. These compounds act as antagonists by stabilizing nonconducting conformations of the chloride channel. Blockage of the GABA-gated chloride channel reduces neuronal inhibition, which leads to hyperexcitation of the central nervous system, convulsions, and death. We recently investigated the mode of action of the silphinenes, plant-derived natural compounds that structurally resemble picrotoxinin. These materials antagonize the action of GABA on insect neurons and block GABA-mediated chloride uptake into mouse brain synaptoneurosomes in a noncompetitive manner. In mammals, avermectins have a blocking action on the GABA-gated chloride channel consistent with a coarse tremor, whereas at longer times and higher concentrations, activation of the channel suppresses neuronal activity. Invertebrates display ataxia, paralysis, and death as the predominant signs of poisoning, with a glutamate-gated chloride channel playing a major role. Additional target sites for the avermectins or other chloride channel-directed compounds might include receptors gated by histamine, serotonin, or acetylcholine.The voltage-sensitive chloride channels form another large gene family of chloride channels. Voltage-dependent chloride channels are involved in a number of physiological processes including: maintenance of electrical excitability, chloride ion secretion and resorption, intravesicular acidification, and cell volume regulation. A subset of these channels is affected by convulsants and insecticides in mammals, although the role they play in acute lethality in insects is unclear. Given the wide range of functions that they mediate, these channels are also potential targets for

Thermoluminescent dosimetric characterization of the perovskite, KMgF3, activated with lanthanum

International Nuclear Information System (INIS)

Sepulveda M, F.

2003-01-01

The new ICRP regulation about the Radiological Protection allows to the different groups to study new thermoluminescent materials highly sensitive for dosimetric applications (personal and environmental). This work reports the relative experimental results to the thermoluminescent characteristic of a new preparation of the fluorine perovskite activated with lanthanum absorbed in polytetrafluoroethylene (KMgF 3 : LaF 3 + Ptfe). The main thermoluminescent properties investigated were: the TL response like a function of the absorbed dose, the attainable accuracy in the dose measurement, the reproducibility of the TL readings and the threshold dose. The obtained results were compared with the requirements of the ANSI protocol for the environmental dosimetry, resulting in a very good agreement with the required yields. (Author)

Effect of substituting cerium-rich mischmetal with lanthanum on high temperature properties of die-cast Mg-Zn-Al-Ca-RE alloys

International Nuclear Information System (INIS)

Anyanwu, Ifeanyi A.; Gokan, Yasuhiro; Suzuki, Atsuya; Kamado, Shigeharu; Kojima, Yo; Takeda, Suguru; Ishida, Taketoshi

2004-01-01

Mg-Zn-Al-Ca-RE alloys have been found to be promising materials for substituting aluminum alloys used for automatic transmission case applications in the automobile industry. Particularly, Mg-0.5%Zn-6%Al-1%Ca-3%RE (ZAXE05613) alloy exhibits comparable creep resistance as ADC12 die-casting aluminum alloy that is currently used for automatic transmission case applications. Changing the rare earth (RE) content of the alloy from mischmetal to lanthanum gives a further improvement in the creep properties of the alloy. Lanthanum addition results in the crystallization of a large amount of acicular Al 11 RE 3 (Al 11 La 3 ) compound along the grain boundaries as well as across the grain boundaries and this effectively controls grain boundary sliding and dislocation motion in the vicinity of the grain boundaries. As a result, die-cast ZAXLa05613 alloy exhibits a higher creep resistance than that of ZAXE05613 alloy

Relation between chloride exchange diffusion and a conductive chloride pathway across the isolated skin of the toad (Bufo bufo)

DEFF Research Database (Denmark)

Kristensen, P; Larsen, Erik Hviid

1978-01-01

Substitution of chloride in the outside bathing medium of the toad skin with bromide, iodide, nitrate and sulphate leads to a reduction in the apparent exchange diffusion of chloride across this tissue, and also to a reduction of the chloride current recorded during hyperpolarization. A series...

Study of the Durability of Doped Lanthanum Manganite and Cobaltite Cathode Materials under ''Real World'' Air Exposure Atmospheres

Energy Technology Data Exchange (ETDEWEB)

Singh, Prabhakar [Univ. of Connecticut, Storrs, CT (United States); Mahapatra, Manoj [Univ. of Connecticut, Storrs, CT (United States); Ramprasad, Rampi [Univ. of Connecticut, Storrs, CT (United States); Minh, Nguyen [Univ. of California, San Diego, CA (United States); Misture, Scott [Alfred Univ., NY (United States)

2014-11-30

The overall objective of the program is to develop and validate mechanisms responsible for the overall structural and chemical degradation of lanthanum manganite as well as lanthanum ferrite cobaltite based cathode when exposed to “real world” air atmosphere exposure conditions during SOFC systems operation. Of particular interest are the evaluation and analysis of degradation phenomena related to and responsible for (a) products formation and interactions with air contaminants, (b) dopant segregation and oxide exolution at free surfaces, (c) cation interdiffusion and reaction products formation at the buried interfaces, (d) interface morphology changes, lattice transformation and the development of interfacial porosity and (e) micro-cracking and delamination from the stack repeat units. Reaction processes have been studied using electrochemical and high temperature materials compatibility tests followed by structural and chemical characterization. Degradation hypothesis has been proposed and validated through further experimentation and computational simulation.

Synthesis of carbon-14 labelled ethyl chloride

International Nuclear Information System (INIS)

Kanski, R.

1976-01-01

A new efficient method of synthesis of ethyl chloride (1,2- 14 C), based on the Ba 14 CO 3 and dry hydrogen chloride as starting materials has been developed and described. Addition of the hydrogen chloride to ethylene (1,2- 14 C), obtained from Ba 14 CO 3 , has been carried out in the presence of the AlCl 3 as catalyst. The outlined method leads to ethyl chloride (1,2- 14 C) of high specific activity. The radiochemical yield of the reaction based on the activity of barium carbonate used was 72%. (author)

Formation of Lanthanum Hydroxide nano structures: Effect of NaOH and KOH solvents

International Nuclear Information System (INIS)

Mazloumi, M.; Zanganeh, S.; Kajbafvala, A.; Shayegh, M. R.; Sadrnezhaad, S. K.

2008-01-01

Lanthanum hydroxide (La(OH) 3 ) nano structures, including elliptical nanoparticles, octahedral rods and irregular nanoparticles were prepared chemically in NaOH and KOH solutions with 10 M concentration. The obtained powders were characterized with x-ray diffraction, scanning electron microscopy, transmission electron microscopy and differential thermal analysis. Crystallinities, morphologies and thermal behavior of the obtained nano structure powders were investigated under the influence of above mentioned solvents. The effect of chemical's temperature was also determined in one of the solvents (i.e. NaOH). The formation of growth in nano structure mechanism under the influence of alkali solutions (i.e., KOH and NaOH) have been discussed considerably in this paper

A meta-analysis of water quality and aquatic macrophyte responses in 18 lakes treated with lanthanum modified bentonite (Phoslock®)

NARCIS (Netherlands)

Spears, Bryan M.; Mackay, Eleanor B.; Yasseri, Said; Gunn, Iain D.M.; Waters, Kate E.; Andrews, Christopher; Cole, Stephanie; De Ville, Mitzi; Kelly, Andrea; Meis, Sebastian; Moore, Alanna L.; Nürnberg, Gertrud K.; van Oosterhout, Frank; Pitt, Jo-Anne; Madgwick, Genevieve; Woods, Helen J.; Lürling, Miquel

2016-01-01

Abstract Lanthanum (La) modified bentonite is being increasingly used as a geo-engineering tool for the control of phosphorus (P) release from lake bed sediments to overlying waters. However, little is known about its effectiveness in controlling P across a wide range of lake conditions or of its

Lanthanum and cerium co-modified Ni/SiO2 catalyst for CO methanation from syngas

Science.gov (United States)

Gong, Dandan; Li, Shuangshuang; Guo, Shaoxia; Tang, Honggui; Wang, Hong; Liu, Yuan

2018-03-01

Sintering of active metal nanoparticles (NPs) and carbon deposition is critical problems for many metal catalysts, such as nickel based catalysts for generating methane from syngas. To improve the resistance to the sintering and carbon deposition, a new scheme was proposed in this work. Lanthanum and cerium co-modified Ni/SiO2 catalysts were synthesized by using perovskite type oxide of La1-xCexNiO3 loaded on SiO2 as the precursor. In a nanocrystallite of La1-xCexNiO3, ions of nickel, lanthanum and cerium are evenly mixed at atomic level and confined in the nanocrystallite, therefore, Ni NPs and the two promoters of La2O3 and CeO2 should be in close contact and highly dispersed on SiO2 after reduction. The catalysts were characterized by using XRD, TEM, BET, H2-TPD, XPS, TG and Raman techniques. Compared with the mono-promoted catalysts, the bi-promoted La0.75Ce0.25NiO3/SiO2 showed much better resistance to carbon deposition, higher resistance to sintering and higher activity for CO methanation, which are attributed to co-eliminating effect of the two promoters for the deposited carbon, confinement of the interacted two promoters for Ni NPs and the higher dispersion of Ni NPs derived from the smaller size of La0.75Ce0.25NiO3.

Chloride sensing by WNK1 kinase involves inhibition of autophosphorylation

Science.gov (United States)

Piala, Alexander T.; Moon, Thomas M.; Akella, Radha; He, Haixia; Cobb, Melanie H.; Goldsmith, Elizabeth J.

2014-01-01

WNK1 [with no lysine (K)] is a serine-threonine kinase associated with a form of familial hypertension. WNK1 is at the top of a kinase cascade leading to phosphorylation of several cotransporters, in particular those transporting sodium, potassium, and chloride (NKCC), sodium and chloride (NCC), and potassium and chloride (KCC). The responsiveness of NKCC, NCC, and KCC to changes in extracellular chloride parallels their phosphorylation state, provoking the proposal that these transporters are controlled by a chloride-sensitive protein kinase. Here, we found that chloride stabilizes the inactive conformation of WNK1, preventing kinase autophosphorylation and activation. Crystallographic studies of inactive WNK1 in the presence of chloride revealed that chloride binds directly to the catalytic site, providing a basis for the unique position of the catalytic lysine. Mutagenesis of the chloride binding site rendered the kinase less sensitive to inhibition of autophosphorylation by chloride, validating the binding site. Thus, these data suggest that WNK1 functions as a chloride sensor through direct binding of a regulatory chloride ion to the active site, which inhibits autophosphorylation. PMID:24803536

Carbon doped lanthanum aluminate (LaAlO3:C) synthesized by solid state reaction for application in UV thermoluminescent dosimetry

International Nuclear Information System (INIS)

Alves, N.

2015-01-01

In this work we discuss the TL output for LaAlO 3 :C crystals grown by using three different combinations of Al 2 O 3 , La 2 O 3 and carbon atoms during the synthesis process. Recently, LaAlO 3 single crystals, co-doped with Ce 3+ and Dy 3+ rare earth trivalent ions and grown under hydrothermal conditions, have been reported to show high thermoluminescent response (TL) when exposed to low levels of ultraviolet radiation (UVR). However, undoped LaAlO 3 synthesized by solid state reaction method from the 1:1 mixture of aluminum and lanthanum oxide under reducing atmosphere revealed to have still higher thermoluminescent sensitivity to UV photon fields than the co-doped with Ce 3+ and Dy 3+ . It is well known that carbon doped aluminum oxide monocrystals have excellent TL and photoluminescent response properties for X-rays, UV and gamma radiation fields. Thus, we conducted three different syntheses of LaAlO 3 by this solid state reaction method, doping the mixture with carbon. The lanthanum aluminate polycrystals were synthesized from the 1:1 mixture of aluminum and lanthanum oxide, adding 0.1wt.% carbon and annealed at 1700°C for two hours in hydrogen atmosphere. The X-ray diffraction analysis revealed the formation of rhombohedral LaAlO 3 crystallographic phase, however a small percentage (15%) of Al 2 O 3 has been also identified. The UV-Vis absorbance spectra were obtained and F and F + - center were ascribed. The UV irradiations were carried out using a commercial 8W UV lamp. Thermoluminescence measurements were performed at a Harshaw 4500 TL reader. All compositions investigated have shown high TL sensitivity to UVR. (author)

Preparation of Carbon-Chitosan-Polyvinyl Chloride (CC-PVC) Material and its Application to Electrochemical Degradation of Methylene Blue in Sodium Chloride Solution

Science.gov (United States)

Riyanto; Prawidha, A. D.

2018-01-01

Electrochemical degradation of methylene blue using Carbon-Chitosan-Polyvinyl Chloride (CC-PVC) electrode in sodium chloride have been done. The aim of this work was to degradation of methylene blue using Carbon-Chitosan-Polyvinyl Chloride (CC-PVC). Carbon chitosan composite electrode was preparing by Carbon and Chitosan powder and PVC in 4 mL tetrahydrofuran (THF) solvent and swirled flatly to homogeneous followed by drying in an oven at 100 °C for 3 h. The mixture was placed in stainless steel mould and pressed at 10 ton/cm2. Sodium chloride was used electrolyte solution. The effects of the current and electrolysis time were investigated using spectrophotometer UV-Visible. The experimental results showed that the carbon-chitosan composite electrode have higher effect in the electrochemical degradation of methylene blue in sodium chloride. Based on UV-visible spectra analysis shows current and electrolysis time has high effect to degradation of methylene blue in sodium chloride. Chitosan and polyvinyl chloride can strengthen the bond between the carbons so that the material has the high stability and conductivity. As conclusions is Carbon-Chitosan-Polyvinyl Chloride (CC-PVC) electrode have a high electrochemical activity for degradation of methylene blue in sodium chloride.

Buried chloride stereochemistry in the Protein Data Bank.

Science.gov (United States)

Carugo, Oliviero

2014-09-23

Despite the chloride anion is involved in fundamental biological processes, its interactions with proteins are little known. In particular, we lack a systematic survey of its coordination spheres. The analysis of a non-redundant set (pairwise sequence identity chloride anion shows that the first coordination spheres of the chlorides are essentially constituted by hydrogen bond donors. Amongst the side-chains positively charged, arginine interacts with chlorides much more frequently than lysine. Although the most common coordination number is 4, the coordination stereochemistry is closer to the expected geometry when the coordination number is 5, suggesting that this is the coordination number towards which the chlorides tend when they interact with proteins. The results of these analyses are useful in interpreting, describing, and validating new protein crystal structures that contain chloride anions.

Chloride Blood Test: MedlinePlus Lab Test Information

Science.gov (United States)

... this page: https://medlineplus.gov/labtests/chloridebloodtest.html Chloride Blood Test To use the sharing features on this page, please enable JavaScript. What is a Chloride Blood Test? A chloride blood test measures the ...

Processes for the production of rare earths from monazite (Paper No. 36)

International Nuclear Information System (INIS)

Murthy, T.K.S.

1979-01-01

A few typical cases are briefly described to illustrate different methods available for rare earth concentration and separation from mixed rare earths chloride obtained for monazite. In the case of cerium, rare earths chloride mixture is treated with sodium sulphate to precipitate rare earths as double sulphates from which hydroxide cake is prepared. The cake is dried to oxidise cerium. Trivalent rare earths are selectively leached and the product is treated with HNO 3 . The resulting ceric nitrate solution is purified by liquid-liquid extraction using TBP. The scrubbed extract is reduced with H 2 O 2 and cerous nitrate is recovered by evaporation. Lanthanum is first concentrated by selective precipitation of hydroxides from rare earths chloride using air-ammonia mixture. The hydroxyde cake is dissolved in HNO 3 and NH 4 NO 3 to get the double nitrate which is subjected to counter current crystallisation for purification. Europium is present at a concentration of 0.01% in the rare earths chloride. It is concentrated in several steps by liquid-liquid extraction using di-2-ethyl hexyl phosphoric acid. The product is purified by selective reduction and europium is obtained as europium sulphate. In the same solvent extraction process samarium and gadolinium are also concentrated to about 25%. They are further upgraded to above 90% purity by repetion of liquid-liquid extraction technique. Cerium, lanthanum and europium obtained by the above processes analyse > 99% as oxides. (M.G.B.)

Atmospheric chloride: Its implication for foliar uptake and damage

Science.gov (United States)

McWilliams, E. L.; Sealy, R. L.

Atmospheric chloride is inversely related to distance from the Texas coast; r2 = 0.86. Levels of atmospheric chloride are higher in the early summer than in the winter because of salt storms. Leaf chloride l'evels of Tillandsia usneoides L. (Spanish moss) reflect the atmospheric chloride levels; r2 = 0.78. The importance of considering the effect of atmospheric chloride on leaf damage to horticultural crops is discussed.

Variation in band gap of lanthanum chromate by transition metals doping LaCr{sub 0.9}A{sub 0.1}O{sub 3} (A:Fe/Co/Ni)

Energy Technology Data Exchange (ETDEWEB)

Naseem, Swaleha, E-mail: wasiamu@gmail.com; Khan, Wasi, E-mail: wasiamu@gmail.com; Saad, A. A., E-mail: wasiamu@gmail.com; Shoeb, M., E-mail: wasiamu@gmail.com; Ahmed, Hilal, E-mail: wasiamu@gmail.com; Naqvi, A. H. [Centre of Excellence in Materials Science (Nanomaterials), Department of Applied Physics, Z.H. College of Engg. and Technology, Aligarh Muslim University, Aligarh-202002 (India); Husain, Shahid [Department of Physics, Aligarh Muslim University, Aligarh-202002 (India)

2014-04-24

Transition metal (Fe, Co, Ni) doped lanthanum chromate (LaCrO{sub 3}) nanoparticles (NPs) were prepared by gel combustion method and calcinated at 800°C. Microstructural studies were carried by XRD and SEM/EDS techniques. The results of structural characterization show the formation of all samples in single phase without any impurity. Optical properties were studied by UV- visible and photoluminescence techniques. The energy band gap was calculated and the variation was observed with the doping of transition metal ions. Photoluminescence spectra show the emission peak maxima for the pure LaCrO{sub 3} at about 315 nm. Influence of Fe, Co, Ni doping was studied and compared with pure lanthanum chromate nanoparticles.

Determination of activity coefficient of lanthanum chloride in molten LiCl-KCl eutectic salt as a function of cesium chloride and lanthanum chloride concentrations using electromotive force measurements

Energy Technology Data Exchange (ETDEWEB)

Bagri, Prashant, E-mail: prashant.bagri@utah.edu; Simpson, Michael F.

2016-12-15

The thermodynamic behavior of lanthanides in molten salt systems is of significant scientific interest for the spent fuel reprocessing of Generation IV reactors. In this study, the apparent standard reduction potential (apparent potential) and activity coefficient of LaCl{sub 3} were determined in a molten salt solution of eutectic LiCl-KCl as a function of concentration of LaCl{sub 3}. The effect of adding up to 1.40 mol % CsCl was also investigated. These properties were determined by measuring the open circuit potential of the La—La(III) redox couple in a high temperature molten salt electrochemical cell. Both the apparent potential and activity coefficient exhibited a strong dependence on concentration. A low concentration (0.69 mol %) of CsCl had no significant effect on the measured properties, while a higher concentration (1.40 mol %) of CsCl caused an increase (become more positive) in the apparent potential and activity coefficient at the higher range of LaCl{sub 3} concentrations.

Influence of chloride admixtures on cement matrix durability

International Nuclear Information System (INIS)

Sheikh, I.A.; Zamorani, E.; Serrini, G.

1989-01-01

The influence of various inorganic salts, as chloride admixtures to Portland cement, on the mechanical properties and the durability of the matrix has been studied. The salts used in this study are chromium, nickel and cadmium chlorides. Improved compressive strength values are obtained which have been correlated to the stable metal hydroxide formation in high pH environment. Under static water conditions at 50 0 C, hydrolyzed chloride ions exhibit adverse effects on the matrix durability through rapid release of calcium as calcium chloride in the initial period of leaching. On the contrary, enhanced matrix durability is obtained on long term leaching in the case of cement containing chromium chloride

[Forensic Analysis for 54 Cases of Suxamethonium Chloride Poisoning].

Science.gov (United States)

Zhao, Y F; Zhao, B Q; Ma, K J; Zhang, J; Chen, F Y

2017-08-01

To observe and analyze the performance of forensic science in the cases of suxa- methonium chloride poisoning, and to improve the identification of suxamethonium chloride poisoning. Fifty-four cases of suxamethonium chloride poisoning were collected. The rules of determination of suxamethonium chloride poisoning were observed by the retrospective analysis of pathological and toxicological changes as well as case features. The pathological features of suxamethonium chloride poisoning were similar to the general changes of sudden death, which mainly included acute pulmonary congestion and edema, and partly showed myocardial disarray and fracture. Suxamethonium chloride could be detected in the heart blood of all cases and in skin tissue of part cases. Suxa-methonium chloride poisoning has the characteristics with fast death and covert means, which are difficult to rescue and easily miss inspection. For the cases of sudden death or suspicious death, determination of suxamethonium chloride should be taken as a routine detection index to prevent missing inspection. Copyright© by the Editorial Department of Journal of Forensic Medicine

Polarization of lanthanum nucleus by dynamic polarization method

International Nuclear Information System (INIS)

Adachi, Toshikazu; Ishimoto, Shigeru; Masuda, Yasuhiro; Morimoto, Kimio

1989-01-01

Preliminary studies have been carried out concerning the application of a dynamic polarization method to polarizing lanthanum fluoride single crystal to be employed as target in experiments with time reversal invariance. The present report briefly outlines the dynamic polarization method and describes some preliminary studies carried out so far. Dynamic polarization is of particular importance because no techniques are currently available that can produce highly polarized static nucleus. Spin interaction between electrons and protons (nuclei) plays a major role in the dynamic polarization method. In a thermal equilibrium state, electrons are polarized almost completely while most protons are not polarized. Positively polarized proton spin is produced by applying microwave to this system. The most hopeful candidate target material is single crystal of LaF 3 containing neodymium because the crystal is chemically stable and easy to handle. The spin direction is of great importance in experiments with time reversal invariance. The spin of neutrons in the target can be cancelled by adjusting the external magnetic field applied to a frozen polarized target. In a frozen spin state, the polarity decreases slowly with a relaxation time that depends on the external magnetic field and temperature. (N.K.)

Production and processing of spinel semi-porous sintered blocks to CAD-CAM with lanthanum-glass infiltration for dental applications

International Nuclear Information System (INIS)

Lourenco, A.A.C.; Ogasawara, T.; Costa Neto, C.A.; Santos, F.V.C.

2009-01-01

The objective of this research was to obtain direct synthesis and sintering spinel by using powder mixing method for CAD-CAM ceramics manufacturing. Powders of alumina and magnesia (71.8 wt% Al2O3 and 28.2 wt% MgO) were mixed with 5 wt% of PVA and PEG binders and homogenized using ball mill (12h), then deagglomerated and submitted to uniaxial pressing into discs and plates (54 to 221.96 MPa), followed by isostatic pressing (186.03 MPa) and sintering at 1500 deg C(GrI) , 1600 C(GrII) and 1700 deg C(GrIII). Characterizations: XRD, density and four-point flexural strength and (for GrIII) elasticity modulus and Vickers microhardness. Lanthanum-glass was infiltrated into samples from all three Groups. Conclusions: (1) Plenty success for the pediatrician method; (2) Maximum density achieved for GrIII, best mechanical strength for GrII (compared to that of commercial product ), this last one being the most indicated for In-Ceram manufacturing via CAD-CAM route; (3) The flexural strength of GrI might be improved a lot after Lanthanum-glass infiltration. (author)

Development of proton conducting materials and membranes based on lanthanum tungstate for hydrogen separation from gas mixtures

International Nuclear Information System (INIS)

Seeger, Janka

2013-01-01

Lanthanum tungstate La 6-x WO 12-δ (named LWO) is a ceramic material with mixed protonic electronic conductivity. Thereby it is a good candidate membrane material for hydrogen separation from synthesis gas in a fossil pre-combustion power plant. This work shows a material optimization by substitution targeted to clearly enhance the mixed conductivity and thereby the hydrogen flow through the LWO membrane. The first part of the work shows the synthesis and characterization of unsubstituted LWO. It points out that monophase LWO powder can be reproducibly synthesized. The La/W-ratio has to be considerably smaller than the nominal ratio of La/W = 6.0. It also depends on the used sintering conditions. Different relevant properties of LWO like stability in conditions close to application, thermal expansion, sintering behavior or microstructure were determined. Furthermore, the electrical conductivity of the material was investigated. LWO exhibits a prevailing protonic conductivity up to 750 C in wet atmospheres. Under dry atmospheres n-type conductivity was dominating. Oxygen ion and n-type conductivity dominated in wet and dry atmospheres above 750 C. The main part of the work is concerned with the development of new LWO based materials by substitutions. The aim is to achieve an improved mixed protonic electronic conductivity. Substitution elements for lanthanum side were Mg, Ca, Sr, Ba, Ce, Nd, Tb, Y and Al, while for the tungsten side Mo, Re and Ir were used. The total conductivity of the developed materials was investigated and compared to that of the unsubstituted LWO. The substitution of lanthanum led to no appreciable enhancement of the conductivity whereas the substitution of tungsten with 20 mol% molybdenum or 20 mol% rhenium clearly improved it. This caused a hydrogen flow about seven times higher for 20 mol% molybdenum- and about ten times higher for 20 mol% rhenium-substituted LWO in comparison with the unsubstituted LWO at 700 C. In the last part of the

Chloride regulates afferent arteriolar contraction in response to depolarization

DEFF Research Database (Denmark)

Hansen, P B; Jensen, B L; Skott, O

1998-01-01

-Renal vascular reactivity is influenced by the level of dietary salt intake. Recent in vitro data suggest that afferent arteriolar contractility is modulated by extracellular chloride. In the present study, we assessed the influence of chloride on K+-induced contraction in isolated perfused rabbit...... afferent arterioles. In 70% of vessels examined, K+-induced contraction was abolished by acute substitution of bath chloride. Consecutive addition of Cl- (30, 60, 80, 100, 110, and 117 mmol/L) restored the sensitivity to K+, and half-maximal response was observed at 82 mmol/L chloride. The calcium channel...... antagonist diltiazem (10(-6) mol/L) abolished K+-induced contractions. Bicarbonate did not modify the sensitivity to chloride. Norepinephrine (10(-6) mol/L) induced full contraction in depolarized vessels even in the absence of chloride. Iodide and nitrate were substituted for chloride with no inhibitory...

Properties of silver chloride track detectors

International Nuclear Information System (INIS)

Dmitriev, V.D.; Kocherov, N.P.; Novikova, N.R.; Perfilov, N.A.

1976-01-01

The experiments on preparation of silver chloride track detectors and their properties are described. The results of X-ray structural analysis and data on sensitivity to charged particles and actinic light of silver chloride crystals, doped with several elements, are presented. (orig.) [de

Polarization study on doped lanthanum gallate electrolyte using impedance spectroscopy

Science.gov (United States)

Gong, Wenquan; Gopalan, Srikanth; Pal, Uday B.

2004-06-01

Alternating current complex impedance spectroscopy studies were conducted on symmetrical cells of the type [gas, electrode/La1-x Sr x Ga1-y Mg y O3 (LSGM) electrolyte/electrode, gas]. The electrode materials were slurry-coated on both sides of the LSGM electrolyte support. The electrodes selected for this investigation are candidate materials for solid oxide fuel cell (SOFC) electrodes. Cathode materials include La1-x Sr x MnO3 (LSM), La1-x Sr x Co y Fe1-y O3 (LSCF), a two-phase particulate composite consisting of LSM and doped-lanthanum gallate (LSGM), and LSCF + LSGM. Pt metal electrodes were also used for the purpose of comparison. Anode material investigated was the Ni + Ce0.85Gd0.15O2 composite. The study revealed important details pertaining to the charge-transfer reactions that occur in such electrodes. The information obtained can be used to design electrodes for intermediate temperature SOFCs based on LSGM electrolytes.

Molten salt synthesis of lead lanthanum zirconate titanate ceramic powders

International Nuclear Information System (INIS)

Cai Zongying; Xing Xianran; Li Lu; Xu Yeming

2008-01-01

Lead lanthanum zirconate titanate (Pb 0.95 La 0.03 )(Zr 0.52 Ti 0.48 )O 3 (PLZT) was synthesized by one step molten salt method with the starting materials of PbC 2 O 4 , La 2 O 3 , ZrO(NO 3 ) 2 .2H 2 O and TiO 2 in the NaCl-KCl eutectic mixtures in the temperature range of 700-1000 deg. C. The single phase of (Pb 0.95 La 0.03 )(Zr 0.52 Ti 0.48 )O 3 powders was prepared at a temperature as low as 850 deg. C for 5 h. The effects of process parameters, such as soaking temperature and time, salt species, and the amount of flux with respect to the starting materials were investigated. The growth process of the PLZT particles in the molten salt undergoes a transition from a diffusion controlled mechanism to an interfacial reaction controlled mechanism at 900 deg. C

Study of magnetic and electrical properties of La doped Mn-Zn nanoferrites synthesized by co-precipitation technique

International Nuclear Information System (INIS)

Panwar, Neena; Thakur, Atul; Thakur, Preeti

2013-01-01

Lanthanum manganese zinc ferrite powder of the composition Mn 0.4 Zn 0.6 La 0.4 Fe 1.6 O 4 were synthesized via co-precipitation technique. Metallic chlorides of manganese, zinc and iron in which Lanthanum is doped were taken. Sodium hydroxide (NaOH) base was used as precipitant agent. The calcinations (presintering) were performed at 700℃ for 3h and sintering at different temperatures 900℃, 850℃, 800℃ also for 3h. The structural investigation of the prepared sample was performed with X-ray diffraction (XRD) and scanning electron microscope (SEM). For studying magnetic properties vibrating sample magnetometer (VSM) are used. Electrical properties were studied by DC resistivity set up. (author)

Microstructural development and characterization of lanthanum chromite-based ceramics to application in solid oxide fuel cells; Desenvolvimento microestrutural e caracterizacao de ceramicas a base de cromita de lantanio para aplicacao em celulas a combustivel de oxido solido

Energy Technology Data Exchange (ETDEWEB)

Oliveira, R.N.; Furtado, J.G. de M.; Soares, C.M.; Serra, E.T. [Centro de Pesquisas de Energia Eletrica (CEPEL), Rio de Janeiro, RJ (Brazil)], e-mail: rnunes@cepel.br

2006-07-01

This work has for objective to investigate and to characterize the microstructural development of lanthanum chromite-based ceramics (LaCrO{sub 3}) doped with earth alkaline metals, correlating the microstructural parameters (mainly the densification level) and processing parameters with the electrothermal properties reached. Lanthanum chromite-based ceramic systems doped with earth-alkaline metals (Ca, Mg and Sr) had been produced from respective metallic nitrates by solid state reactions process. The phase compositions were evaluated by X-ray diffraction and the densification level by Archimedes method. The microstructural characterization was effected by scanning electron microscopy, energy dispersive X-ray spectroscopy and thermal analysis techniques. Electrical tests were used to evaluate the electrical conductivity of the studied ceramics. The obtained results corroborate the literature comments concerning the difficulty of lanthanum chromite-based ceramics with high densification level and evidence the great influence of the nature of the dopants on the sintering mechanism and the microstructural and electric characteristics of the produced ceramics. The best ones results, in terms of densification and electrical conductivity, had been gotten through multiple doping with calcium and strontium, and in sintering temperature conditions lower that the normally considered to pure or monodoped lanthanum chromite-based ceramics. (author)

Chloride Ingress into Concrete under Water Pressure

DEFF Research Database (Denmark)

Lund, Mia Schou; Sander, Lotte Braad; Grelk, Bent

2011-01-01

The chloride ingress into concrete under water pressures of 100 kPa and 800 kPa have been investigated by experiments. The specimens were exposed to a 10% NaCl solution and water mixture. For the concrete having w/c = 0.35 the experimental results show the chloride diffusion coefficient at 800 k......Pa (～8 atm.) is 12 times greater than at 100 kPa (～1 atm.). For w/c = 0.45 and w/c = 0.55 the chloride diffusion coefficients are 7 and 3 times greater. This means that a change in pressure highly influences the chloride ingress into the concrete and thereby the life length models for concrete structures....

Linear Optical Properties of Zinc Borotellurite Glass Doped with Lanthanum Oxide Nanoparticles for Optoelectronic and Photonic Application

Directory of Open Access Journals (Sweden)

Faznny Mohd Fudzi

2017-01-01

Full Text Available Enhancing the optical properties of glasses for the sake of optical application in various fields is an ongoing challenge in materials science and technology. Thus, the optical properties of zinc borotellurite glass doped with lanthanum oxide nanoparticles (La2O3 NPs with the chemical composition of {[(TeO20.7(B2O30.3]0.7(ZnO0.3}1−x (La2O3 NPsx, where x = 0.01, 0.02, 0.03, 0.04, and 0.05 molar fraction, have been investigated. Characterization techniques such as x-ray diffraction, Fourier Transform Infrared Spectroscopy, and Ultraviolet-Visible Spectroscopy are employed to yield the structural properties and optical parameter of the glass. The amorphous nature of the fabricated glasses is confirmed with the presence of a broad hump via XRD diffraction pattern. The decreasing amount of high polarizable nonbridging oxygen as the concentration of La2O3 NPs increases has contributed to the increasing trend of energy band gap in the range of 2.70 to 3.52 eV and decreasing value of refractive index between 2.34 and 2.48. The fabricated glasses that have a higher refractive index than the widely used fiber material, pure silica glass, indicate that zinc borotellurite glass doped with lanthanum nanoparticles is a promising material to be applied as optical fibers.

Hydrolysis of cupric chloride in aqueous ammoniacal ammonium chloride solutions

Directory of Open Access Journals (Sweden)

Limpo, J. L.

1995-06-01

Full Text Available Cupric solubility in the CuCl₂-NH₄Cl-NH₃-H₂O system for chloride concentrations lower than 4 molal in the temperature range 25-60 °C was studied. The experimental results show that for chloride concentration between 3.0 and 1.0 molal the cupric solubility is determined by the solubility of the cupric hydroxychloride Cu(OH_1.5Cl_0.5. For a chloride concentration value of 4.0 molal, there are two cupric compounds, the hydroxychloride Cu(OH_1.5Cl_0.5 or the diammine chloride Cu(NH₃₂Cl₂, on which the solubility of Cu(II depends, according to the temperature and the value of the ratio [NH₃]_Total/[Cu]_Total.

Se estudia la solubilidad del Cu(II en el sistema CuCl₂-NH₄Cl-NH₃-H₂O para concentraciones de cloruro inferiores a 4 molal en el intervalo de temperaturas 25-60 °C. Los resultados experimentales muestran que, para concentraciones de cloruros comprendidas entre 3,0 y 1,0 molal, la solubilidad cúprica viene determinada por la solubilidad del hidroxicloruro cúprico, Cu(OH_1.5Cl_0.5. Para concentraciones de cloruro 4,0 molal, existen dos compuestos cúpricos, el hidroxicloruro, Cu(OH_1.5Cl_0.5 o el cloruro de diamina, Cu(NH₃₂Cl₂, de los que, de acuerdo con la temperatura y con el valor de la relación [NH₃]_Total/[Cu]_Total depende la solubilidad del Cu(II.

29 CFR 1926.1152 - Methylene chloride.

Science.gov (United States)

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Methylene chloride. 1926.1152 Section 1926.1152 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... Methylene chloride. Note: The requirements applicable to construction employment under this section are...

29 CFR 1915.1052 - Methylene chloride.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Methylene chloride. 1915.1052 Section 1915.1052 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... § 1915.1052 Methylene chloride. Note: The requirements applicable to shipyard employment under this...

Thermochemistry of certain rare earth and ammonium double chlorides

International Nuclear Information System (INIS)

Usubaliev, D.U.; Abramtsev, V.A.; Kydynov, M.K.; Vilyaev, A.N.

1987-01-01

In a calorimeter with isothermal casing at 25 deg C dissolution enthalpies of double chlorides of rare earths and ammonium LnCl 3 x2NH 4 Cl (Ln=La, Sm) and LnCl 3 x3NH 4 Cl (Ln=Gd, Tb, Ho) in water, as well as dissolution enthalpy of rare earth chlorides in solution of ammonium chloride and NH 4 Cl in solution of rare earth chloride, have been measured. Formation enthalpies, standard formation enthalpies, dissociation enthalpies of the above-mentioned double chlorides are calculated

Bio-accumulation of lanthanum from lanthanum modified bentonite treatments in lake restoration.

Science.gov (United States)

Waajen, G; van Oosterhout, F; Lürling, M

2017-11-01

Lanthanum (La) modified bentonite (LMB) is one of the available mitigating agents used for the reduction of the phosphorus (P) recycling in eutrophic lakes. The potential toxicity of the La from LMB to aquatic organisms is a matter of concern. In this study the accumulation of La was investigated in the macrophyte Elodea nuttallii, in chironomid larvae and in several fish species during periods up to five years following in situ LMB applications. The application of LMB increased the La concentration of exposed plants and animals. During the first growing season following LMB applications, the La content of E. nuttallii increased 78 fold (3.98-310.68 μg La g -1 DW) to 127 fold (2.46-311.44 μg La g -1 ). During the second growing season following application, the La content decreased but was still raised compared to plants that had not been exposed. The La content of chironomids was doubled in the two years following LMB application, although the increase was not significant. Raised La concentrations in fish liver, bone, muscle and skin were observed two and five years following to LMB application. Liver tissues showed the highest La increase, ranging from 6 fold (0.046-0.285 μg La g -1 DW) to ∼20 fold (0.080-1.886 μg La g -1 , and 0.122-2.109 μg La g -1 ) two years following application and from 6 fold (0.046-0.262 μg La g -1 ) to 13 fold (0.013-0.167 μg La g -1 ) after five years in pelagic and littoral fish. The La content of the liver from Anguilla anguilla (eel) had increased 94 fold (0.034-3.176 μg La g -1 ) two years and 133 fold (0.034-4.538 μg La g -1 ) five years following LMB application. No acute and chronic effects of La accumulation were observed and human health risks are considered negligible. We advocate the long-term study of effects of La accumulation following future LMB applications. Copyright © 2017 Elsevier Ltd. All rights reserved.

Lanthanum titanium perovskite compound: Thin film deposition and high frequency dielectric characterization

International Nuclear Information System (INIS)

Le Paven, C.; Lu, Y.; Nguyen, H.V.; Benzerga, R.; Le Gendre, L.; Rioual, S.; Benzegoutta, D.; Tessier, F.; Cheviré, F.

2014-01-01

Perovskite lanthanum titanium oxide thin films were deposited on (001) MgO, (001) LaAlO 3 and Pt(111)/TiO 2 /SiO 2 /(001)Si substrates by RF magnetron sputtering, using a La 2 Ti 2 O 7 homemade target sputtered under oxygen reactive plasma. The films deposited at 800 °C display a crystalline growth different than those reported on monoclinic ferroelectric La 2 Ti 2 O 7 films. X-ray photoelectron spectroscopy analysis shows the presence of titanium as Ti 4+ ions, with no trace of Ti 3+ , and provides a La/Ti ratio of 1.02. The depositions being performed from a La 2 Ti 2 O 7 target under oxygen rich plasma, the same composition (La 2 Ti 2 O 7 ) is proposed for the deposited films, with an unusual orthorhombic cell and Cmc2 1 space group. The films have a textured growth on MgO and Pt/Si substrates, and are epitaxially grown on LaAlO 3 substrate. The dielectric characterization displays stable values of the dielectric constant and of the losses in the frequency range [0.1–20] GHz. No variation of the dielectric constant has been observed when a DC electric field up to 250 kV/cm was applied, which does not match a classical ferroelectric behavior at high frequencies and room temperature for the proposed La 2 Ti 2 O 7 orthorhombic phase. At 10 GHz and room temperature, the dielectric constant of the obtained La 2 Ti 2 O 7 films is ε ∼ 60 and the losses are low (tanδ < 0.02). - Highlights: • Lanthanum titanium oxide films were deposited by reactive magnetron sputtering. • A La 2 Ti 2 O 7 chemical composition is proposed, with an unusual orthorhombic cell. • At 10 GHz, the dielectric losses are lower than 0.02. • No variation of the dielectric constant is observed under DC electric biasing

21 CFR 177.1950 - Vinyl chloride-ethylene copolymers.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Vinyl chloride-ethylene copolymers. 177.1950... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1950 Vinyl chloride-ethylene copolymers. The vinyl chloride-ethylene copolymers identified in paragraph (a) of this section may be safely...

Chlorides behavior in raw fly ash washing experiments

International Nuclear Information System (INIS)

Zhu Fenfen; Takaoka, Masaki; Oshita, Kazuyuki; Kitajima, Yoshinori; Inada, Yasuhiro; Morisawa, Shinsuke; Tsuno, Hiroshi

2010-01-01

Chloride in fly ash from municipal solid waste incinerators (MSWIs) is one of the obstructive substances in recycling fly ash as building materials. As a result, we have to understand the behavior of chlorides in recycling process, such as washing. In this study, we used X-ray absorption near edge structure (XANES) and X-ray diffraction (XRD) to study the chloride behavior in washed residue of raw fly ash (RFA). We found that a combination of XRD and XANES, which is to use XRD to identify the situation of some compounds first and then process XANES data, was an effective way to explain the chlorides behavior in washing process. Approximately 15% of the chlorine in RFA was in the form of NaCl, 10% was in the form of KCl, 51% was CaCl 2 , and the remainder was in the form of Friedel's salt. In washing experiments not only the mole percentage but also the amount of soluble chlorides including NaCl, KCl and CaCl 2 decreases quickly with the increase of liquid to solid (L/S) ratio or washing frequency. However, those of insoluble chlorides decrease slower. Moreover, Friedel's salt and its related compound (11CaO.7Al 2 O 3 .CaCl 2 ) were reliable standards for the insoluble chlorides in RFA, which are strongly related to CaCl 2 . Washing of RFA promoted the release of insoluble chlorides, most of which were in the form of CaCl 2 .

29 CFR 1915.1017 - Vinyl chloride.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Vinyl chloride. 1915.1017 Section 1915.1017 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... § 1915.1017 Vinyl chloride. Note: The requirements applicable to shipyard employment under this section...

29 CFR 1926.1117 - Vinyl chloride.

Science.gov (United States)

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Vinyl chloride. 1926.1117 Section 1926.1117 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... chloride. Note: The requirements applicable to construction work under this section are identical to those...

Mass transport and chloride ion complexes in occluded cell

International Nuclear Information System (INIS)

Tsuru, T.; Hashimoto, K.; Nishikata, A.; Haruyama, S.

1989-01-01

Changes in the transport and the concentration of ions in a model occluded cell are traced during galvanostatic anodic polarization of a mild steel and a stainless steel. Apparent transport numbers of anions and cations, which were estimated from chemical analysis of solution, were different from those calculated from known mobility data. At the initial stage of the polarization, the transport number of chloride ion was almost unity, and then decreased gradually. For the mild steel, the concentration of total chloride ion accumulated in the occluded compartment increased with the anodic charge passed, and the amount of chloride ion complexed with cations also increased. The chloride complex was estimated as FeCl + . For SUS304 stainless steel, the total chloride ion increased, however, the free chloride ion, which responded to an Ag/AgCl electrode remained approximately 2 mol/dm 3 . Therefore, most of the chloride ions transferred into the occluded cell formed complex ions, such as CrCl n 3-n . The number of chloride ion coordinated to ferrous and chromic ions was estimated from the data fo mass transport for the case of the mild steel and the stainless steel. (author) 9 refs., 14 figs

Evaluating of electronic structure of Lanthanum chromite under doping of divalent ion using density functional theory

International Nuclear Information System (INIS)

Saievar, E.; Gharleghi, A.

2006-01-01

Doping Calcium in Lanthanum site of LaCrO 3 compound increasing the density of states in valance band and decreasing the band gap width because of increases of S electrons in valance band and variety of interaction energies from Cr +3 -Cr +4 couple in valance band. We have used Wien2k software for evaluating this mechanisms. Using of 0.25 percent of dopant and a kind of the space group of cell, let us to use one cell in calculations. We have used GGA approximation in this calculations.

Lanthanum(III) and praseodymium(III) complexes with bidentate and tetradentate Schiff base ligands containing indole ring

International Nuclear Information System (INIS)

Rai, Anita; Sengupta, Soumitra Kumar; Pandey, Om Prakash

2000-01-01

Complexes of lanthanum(III) and praseodymium(III) with Schiff bases, prepared from isatin with aniline, 4-chloroaniline, 2- bromoaniline, 2-nitroaniline (Hl), ethylenediamine, o- phenylenediamine and 4-methyl-o-phenylenediamine (H 2 L') have been synthesised and their physico-chemical properties investigated using elemental analysis, molar conductivities, magnetic susceptibility measurements and spectral (visible, infrared and 1 H NMR) data. The Schiff bases HL bind in a bidentate manner while schiff bases H 2 L' bind in a tetradentate manner. The probable structures of the complexes are proposed. (author)

Anodic Behavior of Alloy 22 in Calcium Chloride and in Calcium Chloride Plus Calcium Nitrate Brines

International Nuclear Information System (INIS)

Evans, K.J.; Day, S.D.; Ilevbare, G.O.; Whalen, M.T.; King, K.J.; Hust, G.A.; Wong, L.L.; Estill, J.C.; Rebak, R.B.

2003-01-01

Alloy 22 (UNS N60622) is a nickel-based alloy, which is extensively used in aggressive industrial applications, especially due to its resistance to localized corrosion and stress corrosion cracking in high chloride environments. The purpose of this work was to characterize the anodic behavior of Alloy 22 in concentrated calcium chloride (CaCl 2 ) brines and to evaluate the inhibitive effect of nitrate, especially to localized corrosion. Standard electrochemical tests such as polarization resistance and cyclic polarization were used. Results show that the corrosion potential of Alloy 22 was approximately -360 mV in the silver-silver chloride (SSC) scale and independent of the tested temperature. Cyclic polarization tests showed that Alloy 22 was mainly susceptible to localized attack in 5 M CaCl 2 at 75 C and higher temperatures. The addition of nitrate in a molar ratio of chloride to nitrate equal to 10 increased the onset of localized corrosion to approximately 105 C. The addition of nitrate to the solution also decreased the uniform corrosion rate and the passive current of the alloy

Process for making rare earth metal chlorides

International Nuclear Information System (INIS)

Kruesi, P.R.

1981-01-01

An uncombined metal or a metal compound such as a sulfide, oxide, carbonate or sulfate is converted in a liquid salt bath to the corresponding metal chloride by reacting it with chlorine gas or a chlorine donor. The process applies to metals of groups 1b, 2a, 2b, 3a, 3b, 4a, 5a and 8 of the periodic table and to the rare earth metals. The chlorine donor may be ferric or sulfur chloride. The liquid fused salt bath is made up of chlorides of alkali metals, alkaline earth metals, ammonia, zinc and ferric iron. Because the formed metal chlorides are soluble in the liquid fused salt bath, they can be recovered by various conventional means

Crystal structures of salicylideneguanylhydrazinium chloride and its copper(II) and cobalt(III) chloride complexes

International Nuclear Information System (INIS)

Chumakov, Yu. M.; Tsapkov, V. I.; Bocelli, G.; Antosyak, B. Ya.; Shova, S. G.; Gulea, A. P.

2006-01-01

The crystal structures of salicylideneguanylhydrazinium chloride hydrate hemiethanol solvate (I), salicylideneguanylhydrazinium trichloroaquacuprate(II) (II), and bis(salicylideneguanylhydrazino)cobalt(III) chloride trihydrate (III) are determined using X-ray diffraction. The structures of compounds I, II, and III are solved by direct methods and refined using the least-squares procedure in the anisotropic approximation for the non-hydrogen atoms to the final factors R = 0.0597, 0.0212, and 0.0283, respectively. In the structure of compound I, the monoprotonated molecules and chlorine ions linked by hydrogen bonds form layers aligned parallel to the (010) plane. In the structure of compound II, the salicylaldehyde guanylhydrazone cations and polymer chains consisting of trichloroaquacuprate(II) anions are joined by an extended three-dimensional network of hydrogen bonds. In the structure of compound III, the [Co(LH) 2 ] + cations, chloride ions, and molecules of crystallization water are linked together by a similar network

Estimating Anthropogenic Emissions of Hydrogen Chloride and Fine Particulate Chloride in China

Science.gov (United States)

Fu, X.; Wang, T.; Wang, S.; Zhang, L.

2017-12-01

Nitryl chloride (ClNO2) can significantly impact the atmospheric photochemistry via photolysis and subsequent reactions of chlorine radical with other gases. The formation of ClNO2 in the atmosphere is sensitive to the emissions of chlorine-containing particulates from oceanic and anthropogenic sources. For China, the only available anthropogenic chlorine emission inventory was compiled for the year 1990 with a coarse resolution of 1 degree. In this study, we developed an up-to-date anthropogenic inventory of hydrogen chloride (HCl) and fine particulate chloride (Cl-) emissions in China for the year 2014, including coal burning, industrial processes, biomass burning and waste burning. Bottom-up and top-down methodologies were combined. Detailed local data (e.g. Cl content in coal, control technologies, etc.) were collected and applied. In order to improve the spatial resolution of emissions, detailed point source information were collected for coal-fired power plants, cement factories, iron & steel factories and waste incineration factories. Uncertainties of this emission inventory and their major causes were analyzed using the Monte Carlo method. This work enables better quantification of the ClNO2 production and impact over China.

Bone marrow scintigraphy with 111In-chloride

International Nuclear Information System (INIS)

Fujishima, Mamoru; Hiraki, Yoshio; Takeda, Yoshihiro; Kohno, Yoshihiro; Niiya, Harutaka; Aono, Kaname; Yorimitsu, Seiichi; Takahashi, Isao

1988-01-01

Bone marrow scintigraphy with indium chloride ( 111 In) was performed in fifty-one patients with the hematological diseases. The results of the investigation were that 1) in all patients, as well as in patients with aplastic anemia, no correlation was there between the degree of the indium chloride accumulation and peripheral blood counts, 2) in patients with aplastic anemia and pure red cell aplasia (PRCA) a tendency to reduction in uptake of indium chloride in bone marrow, 3) in patients with these two good correlation between the degree of indium chloride accumulation and histology of the erythroid bone marrow, but in patients with chronic myelocytic leukemia (CML) and atypical leukemia no correlation between the two, so it seemed unlikely that indium chloride should reflect the effective production of erythrocytes, 4) four patients with leukemia were studied with indium chloride bone marrow imaging two times to evaluate their responses to chemotherapy, and peripheral expansion was no change or reduced in two patients with acute myelocytic leukemia (AML) and one patient with acute lymphocytic leukemia (ALL) who obtained complete remission, but on the other hand, it enlarged in one patient with acute myelocytic leukemia who obtained partial remission, and 5) in two patients with chronic myelocytic leukemia it enlarged up to the ankle joints, which was considerably specific. (author)

Chlorides behavior in raw fly ash washing experiments.

Science.gov (United States)

Zhu, Fenfen; Takaoka, Masaki; Oshita, Kazuyuki; Kitajima, Yoshinori; Inada, Yasuhiro; Morisawa, Shinsuke; Tsuno, Hiroshi

2010-06-15

Chloride in fly ash from municipal solid waste incinerators (MSWIs) is one of the obstructive substances in recycling fly ash as building materials. As a result, we have to understand the behavior of chlorides in recycling process, such as washing. In this study, we used X-ray absorption near edge structure (XANES) and X-ray diffraction (XRD) to study the chloride behavior in washed residue of raw fly ash (RFA). We found that a combination of XRD and XANES, which is to use XRD to identify the situation of some compounds first and then process XANES data, was an effective way to explain the chlorides behavior in washing process. Approximately 15% of the chlorine in RFA was in the form of NaCl, 10% was in the form of KCl, 51% was CaCl(2), and the remainder was in the form of Friedel's salt. In washing experiments not only the mole percentage but also the amount of soluble chlorides including NaCl, KCl and CaCl(2) decreases quickly with the increase of liquid to solid (L/S) ratio or washing frequency. However, those of insoluble chlorides decrease slower. Moreover, Friedel's salt and its related compound (11CaO.7Al(2)O(3).CaCl(2)) were reliable standards for the insoluble chlorides in RFA, which are strongly related to CaCl(2). Washing of RFA promoted the release of insoluble chlorides, most of which were in the form of CaCl(2). Copyright 2010 Elsevier B.V. All rights reserved.

Phytotoxic Effects of Lanthanum Oxide Nanoparticles on Maize (Zea mays L.)

Science.gov (United States)

Liu, Yinglin; Xu, Lina; Dai, Yanhui

2018-02-01

The use of lanthanum oxide nanoparticles (La2O3 NPs) in life products have increased dramatically in the past decades, which are inevitable released into natural environment. In this study, we determined the phytotoxicity of La2O3 NPs to maize (Zea mays L.) grown in one-fourth strength Hoagland solution. After being exposed for two weeks, the biomass, roots length and the relative chlorophyll content were measured. La2O3 NPs had phytotoxicity to maize at 5 mg/L. La2O3 NPs decreased shoot biomass (≥10 mg/L), the root biomass and length (≥5 mg/L). Moreover, La2O3 NPs had adverse effects on the chlorophyll content (≥10 mg/L). The decreased chlorophyll content may reduce net photosynthetic rate. This research offers vital information about the phytotoxicity of La2O3 NPs.

Alkali metal and ammonium chlorides in water and heavy water (binary systems)

CERN Document Server

Cohen-Adad, R

1991-01-01

This volume surveys the data available in the literature for solid-fluid solubility equilibria plus selected solid-liquid-vapour equilibria, for binary systems containing alkali and ammonium chlorides in water or heavy water. Solubilities covered are lithium chloride, sodium chloride, potassium chloride, rubidium chloride, caesium chloride and ammonium chloride in water and heavy water.

Carbon doped lanthanum aluminate (LaAlO3:C) UV thermoluminescent properties synthesized by solid state reaction with three different mixing methodologies

International Nuclear Information System (INIS)

Alves, N.

2017-01-01

In this work we discuss the thermoluminescent (TL) response for LaAlO 3 :C crystals grown by using three different combinations of Al 2 O 3 , La 2 O 3 and carbon atoms during the synthesis process. Recently, LaAlO 3 single crystals, co-doped with Ce 3+ and Dy 3+ rare earth trivalent ions and grown under hydrothermal conditions, have been reported to show high thermoluminescent response (TL) when exposed to low levels of ultraviolet radiation (UVR). However, undoped LaAlO 3 synthesized by solid state reaction method from the 1:1 mixture of aluminum and lanthanum oxide under reducing atmosphere revealed to have still higher thermoluminescent sensitivity to UV photon fields than the co-doped with Ce 3+ and Dy 3+ . It is well known that carbon doped aluminum oxide monocrystals have excellent TL and photoluminescent response properties for X-rays, UV and gamma radiation fields. Thus, we conducted three different syntheses of LaAlO 3 by the solid state reaction method, doping the mixture with carbon. The lanthanum aluminate polycrystals were synthesized from the 1:1 mixture of aluminum and lanthanum oxide, adding 0.1wt.% carbon and annealed at 1700°C for two hours in hydrogen atmosphere. The X-ray diffraction analysis revealed the formation of rhombohedral LaAlO 3 crystallographic phase, however a small percentage (15%) of Al 2 O 3 has been also identified. The UV-Vis absorbance spectra were obtained and F and F + - center were ascribed. The UV irradiations were carried out using a commercial 8W UV lamp. Thermoluminescence measurements were performed at a Harshaw 4500 TL reader. All compositions investigated have shown high TL sensitivity to UVR. (author)

Studies on the mercuric chloride resistance of Staphylococcus aureus

Energy Technology Data Exchange (ETDEWEB)

Vaczi, L; Fodor, M; Milch, H; Rethy, A

1962-01-01

Among 409 pathogenic Staph. aureus strains 34% have been found to be sensitive, and 66% resistant, to mercuric chloride. The incidence of mercuric chloride resistant cultures among antibiotic sensitive staphylococci was 20%; among strains resistant to penicillin or to more than one antibiotic, 70%. Mercuric chloride resistant organisms occurred chiefly among phage group I and untypable strains; they were especially common among the so called epidemic strains of phage group I, and among cultures resistant to 4-6 antibiotics. In mercuric chloride sensitivity a thirtyfold, in merthiolate sensitivity only a two-fold difference has been revealed among the strains. The sulfydryl group content of mercuric chloride resistant organisms was only 1 1/2 times higher than that of sensitive bacteria. As to p-chlor mercuric benzoate binding capacity, a twofold difference was found between mercuric chloride sensitive and resistant staphylococci. The differences in the mercuric chloride resistance of various staphylococcal strains might be due to differences in the chemical structure of the cell surface. 9 references, 1 figure, 6 tables.

Ductility of Mo–12Si–8.5B alloys doped with lanthanum oxide by the liquid–liquid doping method

Energy Technology Data Exchange (ETDEWEB)

Li, Wenhu [School of Materials Science & Engineering, Xi’an University of Technology, Xi’an 710048 (China); School of Materials Science & Engineering, Shaanxi University of Technology, Hanzhong 723000 (China); Zhang, Guojun, E-mail: zhangguojun@xaut.edu.cn [School of Materials Science & Engineering, Xi’an University of Technology, Xi’an 710048 (China); Wang, Shixiong [School of Materials Science & Engineering, Xi’an University of Technology, Xi’an 710048 (China); Li, Bin; Sun, Jun [State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049 (China)

2015-09-05

Highlights: • Alloys doping lanthanum oxide by L–L doped method were prepared by hot pressing. • The compression strength of alloys are superior. • The fracture toughness of alloys is improved by L–L doped method. - Abstract: Mo–12Si–8.5B (Mo–Si–B) alloys doped with different mass fractions (0.3 wt%, 0.6 wt%, and 0.9 wt%) of lanthanum oxide (La{sub 2}O{sub 3}) were prepared by liquid–liquid (L–L) doping, mechanical alloying and hot pressing sintering techniques. The observation of the microstructures of the Mo–Si–B alloys reveals that the grain sizes of the alloys were refined with the increase in La{sub 2}O{sub 3} doping. The fracture toughness values of the alloys of over 10 MPa m{sup 1/2} reveal that the addition of La{sub 2}O{sub 3} via the L–L doping method can obviously improve the alloy fracture toughness compared to the alloys doped with La{sub 2}O{sub 3} via the solid–solid (S–S) doping method. In addition, compression tests indicate that the compression strength of the alloys was improved compared to Mo–12Si–8.5B alloys.

40 CFR 61.64 - Emission standard for polyvinyl chloride plants.

Science.gov (United States)

2010-07-01

... chloride plants. 61.64 Section 61.64 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Standard for Vinyl Chloride § 61.64 Emission standard for polyvinyl chloride plants. An owner or operator of a polyvinyl chloride plant shall comply with the requirements of this section and § 61.65. (a...

Removal of iron contaminant from zirconium chloride solution

International Nuclear Information System (INIS)

Voit, D.O.

1992-01-01

This patent describes a process for eliminating iron contaminant from an aqueous zirconium chloride solution that has been contaminated with FeCl 3 in a plant in which zirconium and hafnium chloride solutions are separated by a main MINK solvent extraction system and the FeCl 3 is normally removed from the zirconium chloride solution by a secondary MINK solvent extraction system

NuLYTELY (PEG 3350, sodium chloride, sodium bicarbonate and potassium chloride for oral solution).

Science.gov (United States)

Swartz, M L

1992-02-01

NuLYTELY (PEG 3350, Sodium Chloride, Sodium Bicarbonate, and Potassium Chloride for Oral Solution), a product from Braintree Laboratories, Inc. is a modification of GoLYTELY (PEG 3350 and Electrolytes for Oral Solution) that has been found to have the same therapeutic advantages in terms of safety, efficacy, speed and patient acceptance. This product was developed to improve upon the taste of GoLYTELY. NuLYTELY represents an effective alternative for bowel cleansing prior to colonoscopy that may be more acceptable to some patients.

[Determination of Chloride Salt Solution by NIR Spectroscopy].

Science.gov (United States)

Zhang, Bin; Chen, Jian-hong; Jiao, Ming-xing

2015-07-01

Determination of chloride salt solution by near infrared spectrum plays a very important role in Biomedicine. The near infrared spectrum analysis of Sodium chloride, potassium chloride, calcium chloride aqueous solution shows that the concentration change of chloride salt can affect hydrogen bond, resulting in the variation of near infrared spectrum of water. The temperature influence on NIR spectrum has been decreased by choosing reasonable wavelength range and the wavelength where the temperature effects are zero (isosbestic point). Chlorine salt prediction model was established based on partial least squares method and used for predicting the concentration of the chlorine ion. The impact on near infrared spectrum of the cation ionic radius, the number of ionic charge, the complex effect of ionic in water has also discussed in this article and the reason of every factor are analysed. Experimental results show that the temperature and concentration will affect the near-infrared spectrum of the solution, It is found that the effect of temperature plays the dominant role at low concentrations of chlorine salt; rather, the ionic dominates at high concentration. Chloride complexes are formed in aqueous solution, It has an effect on hydrogen bond of water combining with the cations in chlorine salt solution, Comparing different chloride solutions at the same concentration, the destruction effects of chloride complexes and catnions on the hydrogen bond of water increases in the sequences: CaCl2 >NaCl>KC. The modeling result shows that the determination coefficients (R2) = 99.97%, the root mean square error of cross validation (RM- SECV) = 4.51, and the residual prediction deviation (RPD) = 62.7, it meets the daily requirements of biochemical detection accuracy.

Detection of colloidal silver chloride near solubility limit

Science.gov (United States)

Putri, K. Y.; Adawiah, R.

2018-03-01

Detection of nanoparticles in solution has been made possible by several means; one of them is laser-induced breakdown detection (LIBD). LIBD is able to distinguish colloids of various sizes and concentrations. This technique has been used in several solubility studies. In this study, the formation of colloids in a mixed system of silver nitrate and sodium chloride was observed by acoustic LIBD. Silver chloride has low solubility limit, therefore LIBD measurement is appropriate. Silver and chloride solutions with equal concentrations, set at below and above the solubility of silver chloride as the expected solid product, were mixed and the resulting colloids were observed. The result of LIBD measurement showed that larger particles were present as more silver and chloride introduced. However, once the concentrations exceeded the solubility limit of silver chloride, the detected particle size seemed to be decreasing, hence suggested the occurrence of coprecipitation process. This phenomenon indicated that the ability of LIBD to detect even small changes in colloid amounts might be a useful tool in study on formation and stability of colloids, i.e. to confirm whether nanoparticles synthesis has been successfully performed and whether the system is stable or not.

Effects of platinic chloride on Tetrahymena pyrifromis GL

DEFF Research Database (Denmark)

Nilsson, Jytte R.

1992-01-01

Cellebiologi, platinum(IV)chloride, endocytosis, detoxification, cell proliferation, fine structure, cisplatin......Cellebiologi, platinum(IV)chloride, endocytosis, detoxification, cell proliferation, fine structure, cisplatin...

Selective dehydration of bio-ethanol to ethylene catalyzed by lanthanum-phosphorous-modified HZSM-5: influence of the fusel.

Science.gov (United States)

Hu, Yaochi; Zhan, Nina; Dou, Chang; Huang, He; Han, Yuwang; Yu, Dinghua; Hu, Yi

2010-11-01

Bio-ethanol dehydration to ethylene is an attractive alternative to oil-based ethylene. The influence of fusel, main byproducts in the fermentation process of bio-ethanol production, on the bio-ethanol dehydration should not be ignored. We studied the catalytic dehydration of bio-ethanol to ethylene over parent and modified HZSM-5 at 250°C, with weight hourly space velocity (WHSV) equal to 2.0/h. The influences of a series of fusel, such as isopropanol, isobutanol and isopentanol, on the ethanol dehydration over the catalysts were investigated. The 0.5%La-2%PHZSM-5 catalyst exhibited higher ethanol conversion (100%), ethylene selectivity (99%), and especially enhanced stability (more than 70 h) than the parent and other modified HZSM-5. We demonstrated that the introduction of lanthanum and phosphorous to HZSM-5 could weaken the negative influence of fusel on the formation of ethylene. The physicochemical properties of the catalysts were characterized by ammonia temperature-programmed desorption (NH(3)-TPD), nitrogen adsorption and thermogravimetry (TG)/differential thermogravimetry (DTG)/differential thermal analysis (DTA) (TG/DTG/DTA) techniques. The results indicated that the introduction of lanthanum and phosphorous to HZSM-5 could inhibit the formation of coking during the ethanol dehydration to ethylene in the presence of fusel. The development of an efficient catalyst is one of the key technologies for the industrialization of bio-ethylene.

Surface Chloride Levels in Colorado Structural Concrete

Science.gov (United States)

2018-01-01

This project focused on the chloride-induced corrosion of reinforcing steel in structural concrete. The primary goal of this project is to analyze the surface chloride concentration level of the concrete bridge decks throughout Colorado. The study in...

Simple chloride sensors for continuous groundwater monitoring

DEFF Research Database (Denmark)

Thorn, Paul; Mortensen, John

2012-01-01

The development of chloride sensors which can be used for continuous, on-line monitoring of groundwater could be very valuable in the management of our coastal water resources. However, sensor stability, drift, and durability all need to be addressed in order for the sensors to be used in continu......The development of chloride sensors which can be used for continuous, on-line monitoring of groundwater could be very valuable in the management of our coastal water resources. However, sensor stability, drift, and durability all need to be addressed in order for the sensors to be used...... in continuous application. This study looks at the development of a simple, inexpensive chloride electrode, and evaluates its performance under continuous use, both in the laboratory and in a field test in a monitoring well. The results from the study showed a consistent response to changing chloride...... concentrations over longer periods. The signal was seen to be stable, with regular drift in both laboratory and field test. In the field application, the sensor signal was corrected for drift, and errors were observed to be under 7% of that of conductivity measurements. The study also found that the chloride...

Interpretation of postmortem vitreous concentrations of sodium and chloride.

Science.gov (United States)

Zilg, B; Alkass, K; Berg, S; Druid, H

2016-06-01

Vitreous fluid can be used to analyze sodium and chloride levels in deceased persons, but it remains unclear to what extent such results can be used to diagnose antemortem sodium or chloride imbalances. In this study we present vitreous sodium and chloride levels from more than 3000 cases. We show that vitreous sodium and chloride levels both decrease with approximately 2.2mmol/L per day after death. Since potassium is a well-established marker for postmortem interval (PMI) and easily can be analyzed along with sodium and chloride, we have correlated sodium and chloride levels with the potassium levels and present postmortem reference ranges relative the potassium levels. We found that virtually all cases outside the reference range show signs of antemortem hypo- or hypernatremia. Vitreous sodium or chloride levels can be the only means to diagnose cases of water or salt intoxication, beer potomania or dehydration. We further show that postmortem vitreous sodium and chloride strongly correlate and in practice can be used interchangeably if analysis of one of the ions fails. It has been suggested that vitreous sodium and chloride levels can be used to diagnose drowning or to distinguish saltwater from freshwater drowning. Our results show that in cases of freshwater drowning, vitreous sodium levels are decreased, but that this mainly is an effect of postmortem diffusion between the eye and surrounding water rather than due to the drowning process, since the decrease in sodium levels correlates with immersion time. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Method of processing radioactive metallic sodium with recycling alcohols

International Nuclear Information System (INIS)

Sakai, Takuhiko; Mitsuzuka, Norimasa.

1980-01-01

Purpose: To employ high safety alcohol procession and decrease the amount of wastes in the procession of radioactive metallic sodium discharged from LMFBR type reactors. Method: Radioactive metallic sodium containing long half-decay period nuclides such as cesium, strontium, barium, cerium, lanthanum or zirconium is dissolved in an alcohol at about 70% purity. After extracting the sodium alcoholate thus formed, gaseous hydrochloride is blown-in to separate the sodium alcoholate into alcohol and sodium chloride, and regenerated alcohol is used again for dissolving sodium metal. The sodium chloride thus separated is processed into solid wastes. (Furukawa, Y.)

Chloride equilibrium potential in salamander cones

Directory of Open Access Journals (Sweden)

Bryson Eric J

2004-12-01

Full Text Available Abstract Background GABAergic inhibition and effects of intracellular chloride ions on calcium channel activity have been proposed to regulate neurotransmission from photoreceptors. To assess the impact of these and other chloride-dependent mechanisms on release from cones, the chloride equilibrium potential (ECl was determined in red-sensitive, large single cones from the tiger salamander retinal slice. Results Whole cell recordings were done using gramicidin perforated patch techniques to maintain endogenous Cl- levels. Membrane potentials were corrected for liquid junction potentials. Cone resting potentials were found to average -46 mV. To measure ECl, we applied long depolarizing steps to activate the calcium-activated chloride current (ICl(Ca and then determined the reversal potential for the current component that was inhibited by the Cl- channel blocker, niflumic acid. With this method, ECl was found to average -46 mV. In a complementary approach, we used a Cl-sensitive dye, MEQ, to measure the Cl- flux produced by depolarization with elevated concentrations of K+. The membrane potentials produced by the various high K+ solutions were measured in separate current clamp experiments. Consistent with electrophysiological experiments, MEQ fluorescence measurements indicated that ECl was below -36 mV. Conclusions The results of this study indicate that ECl is close to the dark resting potential. This will minimize the impact of chloride-dependent presynaptic mechanisms in cone terminals involving GABAa receptors, glutamate transporters and ICl(Ca.

Hydrolysis of ferric chloride in solution

International Nuclear Information System (INIS)

Lussiez, G.; Beckstead, L.

1996-11-01

The Detox trademark process uses concentrated ferric chloride and small amounts of catalysts to oxidize organic compounds. It is under consideration for oxidizing transuranic organic wastes. Although the solution is reused extensively, at some point it will reach the acceptable limit of radioactivity or maximum solubility of the radioisotopes. This solution could be cemented, but the volume would be increased substantially because of the poor compatibility of chlorides and cement. A process has been developed that recovers the chloride ions as HCl and either minimizes the volume of radioactive waste or permits recycling of the radioactive chlorides. The process involves a two-step hydrolysis at atmospheric pressure, or preferably under a slight vacuum, and relatively low temperature, about 200 degrees C. During the first step of the process, hydrolysis occurs according to the reaction below: FeCl 3 liquid + H 2 O → FeOCl solid + 2 HCl gas During the second step, the hot, solid, iron oxychloride is sprayed with water or placed in contact with steam, and hydrolysis proceeds to the iron oxide according to the following reaction: 2 FeOCl solid + H 2 O → Fe 2 O 3 solid + 2 HCl gas . The iron oxide, which contains radioisotopes, can then be disposed of by cementation or encapsulation. Alternately, these chlorides can be washed off of the solids and can then either be recycled or disposed of in some other way

Transport and fate of chloride from road salt within a mixed urban and agricultural watershed in Illinois (USA): assessing the influence of chloride application rates

Science.gov (United States)

Ludwikowski, Jessica J.; Peterson, Eric W.

2018-01-01

In a typical winter season, approximately 471,000 tons of road salt are deposited along roadways in Illinois, USA. An estimated 45% of the deposited road salt will infiltrate through the soils and into shallow aquifers. Transported through shallow aquifers, chloride associated with the road salts has the potential to reside within groundwater for years based on the pathway, the geologic material, and the recharge rate of the aquifer system. Utilizing MODFLOW and MT3D, simulations employing various road-salt application rates were conducted to assess the net accumulation of chloride and the residence times of chloride in an agriculture-dominated watershed that originates in an urban area. A positive-linear relationship was observed between the application rate of chloride and both the maximum chloride concentration and total mass accumulated within the watershed. Simulated annual recharge rates along impacted surfaces ranged from 1,000 to 10,000 mg/L. After 60 years of application, simulated chloride concentrations in groundwater ranged from 197 to 1,900 mg/L. For all application rates, chloride concentrations within the groundwater rose at an annual rate of >3 mg/L. While concentrations increase throughout the system, the majority of chloride accumulation occurs near the roads and the urban areas. Model simulations reveal a positive relationship between application rate and residence time of chloride (1,123-1,288 days based on application rate). The models indicate that continued accumulation of chloride in shallow aquifers can be expected, and methods that apply less chloride effectively need to be examined.

Lanthanum triflate triggered synthesis of tetrahydroquinazolinone derivatives of N-allyl quinolone and their biological assessment

Directory of Open Access Journals (Sweden)

Jardosh Hardik H.

2012-01-01

Full Text Available A series of 24 derivatives of tetrahydroquinazolinone has been synthesized by one-pot cyclocondensation reaction of N-allyl quinolones, cyclic β-diketones and (thiourea/N-phenylthiourea in presence of lanthanum triflate catalyst. This methodology allowed us to achieve the products in excellent yield by stirring at room temperature. All the synthesized compounds were investigated against a representative panel of pathogenic strains using broth microdilution MIC (minimum inhibitory concentration method for their in vitro antimicrobial activity. Amongst these sets of heterocyclic compounds 5h, 6b, 6h, 5f, 5l, 5n and 6g found to have admirable activity.

Extractive process for preparing high purity magnesium chloride hexahydrate

Directory of Open Access Journals (Sweden)

Fezei Radouanne

2012-01-01

Full Text Available This paper refers a method for the preparation of magnesium chloride hexahydrate (bischofite from Sebkha el Melah of Zarzis Tunisian natural brine. It is a five-stage process essentially based on crystallization by isothermal evaporation and chemical precipitation. The two first steps were dedicated to the crystallization of sodium chloride and potassiummagnesium double salts, respectively. Then, the resulting liquor was desulfated using calcium chloride solution. After that another isothermal evaporation stage was implemented in order to eliminate potassium ions in the form of carnallite, KCl.MgCl2.6H2O. At the end of this step, the recovered solution primarily composed of magnesium and chloride ions was treated by dioxan in order to precipitate magnesium chloride as MgCl2.6H2O.C4H8O2. This compound dried at constant temperature of 100°C gave good quality magnesium chloride hexahydrate. Besides this salt, the various by-products obtained from the different treatment stages are also useful.

Estimation of cerium and lanthanum content in core material of high intensity carbon arc electrodes by x-ray fluorescence method

International Nuclear Information System (INIS)

Nagpal, K.C.; Bhavalkar, R.H.

1977-01-01

The X-ray fluorescence method has been used to determine the weight percentages of cerium and lanthanum in the core material of high intensity carbon arc electrodes from the calibration curves plotted between the weight percentages of these elements and the peak-intensity ratios of CeLsub(α1), and LaLsub(α1) peaks to the neighbouring peak SnLsub(α1) due to an internal standard element. (author)

Influence of crystal phases on electro-optic properties of epitaxially grown lanthanum-modified lead zirconate titanate films

Science.gov (United States)

Masuda, Shin; Seki, Atsushi; Masuda, Yoichiro

2010-02-01

We describe here how we have improved the crystal qualities and controlled the crystal phase of the lanthanum-modified lead zirconate titanate (PLZT) film without changing the composition ratio using an oxygen-pressure crystallization process. A PLZT film deposited on a SrTiO3 substrate with the largest electro-optic (EO) coefficient of 498 pm/V has been achieved by controlling the crystal phase of the film. Additionally, a fatigue-free lead zirconate titanate (PZT) capacitor with platinum electrodes has been realized by reducing the oxygen vacancies in the films.

Deposition of Lanthanum Strontium Cobalt Ferrite (LSCF) Using Suspension Plasma Spraying for Oxygen Transport Membrane Applications

Science.gov (United States)

Fan, E. S. C.; Kesler, O.

2015-08-01

Suspension plasma spray deposition was utilized to fabricate dense lanthanum strontium cobalt ferrite oxygen separation membranes (OSMs) on porous metal substrates for mechanical support. The as-sprayed membranes had negligible and/or reversible material decomposition. At the longer stand-off distance (80 mm), smooth and dense membranes could be manufactured using a plasma with power below approximately 81 kW. Moreover, a membrane of 55 μm was observed to have very low gas leakage rates desirable for OSM applications. This thickness could potentially be decreased further to improve oxygen diffusion by using metal substrates with finer surface pores.

Solid-phase extraction of cobalt(II) from lithium chloride solutions using a poly(vinyl chloride)-based polymer inclusion membrane with Aliquat 336 as the carrier.

Science.gov (United States)

Kagaya, Shigehiro; Cattrall, Robert W; Kolev, Spas D

2011-01-01

The extraction of cobalt(II) from solutions containing various concentrations of lithium chloride, hydrochloric acid, and mixtures of lithium chloride plus hydrochloric acid is reported using a poly(vinyl chloride) (PVC)-based polymer inclusion membrane (PIM) containing 40% (w/w) Aliquat 336 as a carrier. The extraction from lithium chloride solutions and mixtures with hydrochloric acid is shown to be more effective than extraction from hydrochloric acid solutions alone. The solution concentrations giving the highest amounts of extraction are 7 mol L(-1) for lithium chloride and 8 mol L(-1) lithium chloride plus 1 mol L(-1) hydrochloric acid for mixed solutions. Cobalt(II) is easily stripped from the membrane using deionized water. The cobalt(II) species extracted into the membrane are CoCl(4)(2-) for lithium chloride solutions and HCoCl(4)(-) for mixed solutions; these form ion-pairs with Aliquat 336. It is also shown that both lithium chloride and hydrochloric acid are extracted by the PIM and suppress the extraction of cobalt(II) by forming ion-pairs in the membrane (i.e. R(3)MeN(+)·HCl(2)(-) for hydrochloric acid and R(3)MeN(+)·LiCl(2)(-) for lithium chloride). 2011 © The Japan Society for Analytical Chemistry

40 CFR 721.6167 - Piperdinium, 1,1-dimethyl-, chloride.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Piperdinium, 1,1-dimethyl-, chloride... Substances § 721.6167 Piperdinium, 1,1-dimethyl-, chloride. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as piperdinium, 1,1-dimethyl-, chloride. (PMN...

Synthesis of 14C-dehydrocorydaline chloride

International Nuclear Information System (INIS)

Zhang Rui; Wang Ding

1988-01-01

A method for synthesis of 14 C-dehydrocorydaline chloride is described. In the presence of sodium hydroxide, acetonylpalmatine is reacted with 14 C-methyl iodide in sealed glass ampoule to give 14 C-13-methylpalmatine iodide which is then converted to chloride. The radiochemical purity of 14 C-dehydrocorydaline determined by TLC is over 98% and the labelling efficiency is 54%

Lanthanum-silicon-substituted hydroxyapatite: Mechanochemical synthesis and prospects for medical applications

Energy Technology Data Exchange (ETDEWEB)

Chaikina, M. V., E-mail: chaikinam@solid.nsc.ru; Bulina, N. V., E-mail: bulina@solid.nsc.ru; Prosanov, I. Yu., E-mail: prosanov@mail.ru [Institute of Solid State Chemistry and Mechanochemistry SB RAS, Kutateladze Street 18, Novosibirsk, 630128 (Russian Federation); Komarova, E. G., E-mail: katerina@ispms.tsc.ru; Sharkeev, Yu. P., E-mail: sharkeev@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Academicheskii Pr. 2/4, Tomsk, 634055 (Russian Federation)

2016-08-02

The paper presents the results of mechanochemical synthesis of hydroxyapatite (HAP) with simultaneous substitutions of lanthanum (La{sup 3+}) for calcium ions and silicate ((SiO{sub 4}){sup 4−}-group) for the phosphate group with the substituent concentrations in the range 0.2–2.0 mol per HAP mol. The use of Si-substituted HAP as a coating material promotes accelerated osteosynthesis and osteointegration of implants into the bone tissue. The replacement of calcium ions by La{sup 3+} in the HAP structure plays an antimicrobial role preventing inflammatory processes. Annealing-induced variations in the lattice parameters of synthesized samples indicate the substituent incorporation into the HAP structure. It is known that complex compounds with lanthanides are used for cancer chemotherapy. In particular, La plays a key role in the course of treatment of injured defects of bone tissue. In addition, La-substituted HAP can be used for filling bone defects and coating implants in postoperational areas affected by bone cancer.

Chloride ingress in cement paste and mortar

DEFF Research Database (Denmark)

Jensen, Ole Mejlhede; Hansen, Per Freiesleben; Coats, Alison M.

1999-01-01

In this paper chloride ingress in cement paste and mortar is followed by electron probe microanalysis. The influence of several paste and exposure parameters on chloride ingress are examined (e.g., water-cement ratio, silica fume addition, exposure time, and temperature), The measurements...

Chronopotentiometric chloride sensing using transition time measurement

NARCIS (Netherlands)

Abbas, Yawar; de Graaf, D.B.; Olthuis, Wouter; van den Berg, Albert

2013-01-01

Detection of chloride ions is crucial to accurately access the concrete structure durability[1]. The existing electrochemical method of chloride ions detection in concrete, potentiometry[1], is not suitable for in-situ measurement due to the long term stability issue of conventional reference

Method for synthesizing pollucite from chabazite and cesium chloride

International Nuclear Information System (INIS)

Pereira, C.

1999-01-01

A method is described for immobilizing waste chlorides salts containing radionuclides and hazardous nuclear material for permanent disposal, and in particular, a method is described for immobilizing waste chloride salts containing cesium, in a synthetic form of pollucite. The method for synthesizing pollucite from chabazite and cesium chloride includes mixing dry, non-aqueous cesium chloride with chabazite and heating the mixture to a temperature greater than the melting temperature of the cesium chloride, or above about 700 C. The method further comprises significantly improving the rate of retention of cesium in ceramic products comprised of a salt-loaded zeolite by adding about 10% chabazite by weight to the salt-loaded zeolite prior to conversion at elevated temperatures and pressures to the ceramic composite. 3 figs

Mercury toxicity in the shark (Squalus acanthias) rectal gland: apical CFTR chloride channels are inhibited by mercuric chloride.

Science.gov (United States)

Ratner, Martha A; Decker, Sarah E; Aller, Stephen G; Weber, Gerhard; Forrest, John N

2006-03-01

In the shark rectal gland, basolateral membrane proteins have been suggested as targets for mercury. To examine the membrane polarity of mercury toxicity, we performed experiments in three preparations: isolated perfused rectal glands, primary monolayer cultures of rectal gland epithelial cells, and Xenopus oocytes expressing the shark cystic fibrosis transmembrane conductance regulator (CFTR) chloride channel. In perfused rectal glands we observed: (1) a dose-dependent inhibition by mercury of forskolin/3-isobutyl-1-methylxanthine (IBMX)-stimulated chloride secretion; (2) inhibition was maximal when mercury was added before stimulation with forskolin/IBMX; (3) dithiothrietol (DTT) and glutathione (GSH) completely prevented inhibition of chloride secretion. Short-circuit current (Isc) measurements in monolayers of rectal gland epithelial cells were performed to examine the membrane polarity of this effect. Mercuric chloride inhibited Isc more potently when applied to the solution bathing the apical vs. the basolateral membrane (23 +/- 5% and 68 +/- 5% inhibition at 1 and 10 microM HgCl2 in the apical solution vs. 2 +/- 0.9% and 14 +/- 5% in the basolateral solution). This inhibition was prevented by pre-treatment with apical DTT or GSH; however, only the permeant reducing agent DTT reversed mercury inhibition when added after exposure. When the shark rectal gland CFTR channel was expressed in Xenopus oocytes and chloride conductance was measured by two-electrode voltage clamping, we found that 1 microM HgCl2 inhibited forskolin/IBMX conductance by 69.2 +/- 2.0%. We conclude that in the shark rectal gland, mercury inhibits chloride secretion by interacting with the apical membrane and that CFTR is the likely site of this action. Copyright 2006 Wiley-Liss, Inc.

On solubility of rare earth chlorides in water at different temperatures

International Nuclear Information System (INIS)

Nikolaev, A.V.; Sorokina, A.A.; Sokolova, N.P.; Kotlyar-Shapirov, G.S.; Bagryantseva, L.I.

1978-01-01

Solubility of rare earth chlorides at -5, -10 and -15 deg C is studied. Rare earth chloride solubility dependences on the temperature in the interval from -15 to 50 deg C are presented. Decrease of solubility temperature coefficient to a zero is observed at temperature drop almost for all rare earth chlorides. Solubility temperature coefficient at the same temperature but for different rare earth chlorides reduces appreciably with the growth of rare earth chloride serial number. This testifies to the corresponding decrease of integral solution heat of rare earth chloride crystallohydrates

Effects of lanthanum and acid rain stress on the bio-sequestration of lanthanum in phytoliths in germinated rice seeds

Science.gov (United States)

Si, Yong; Wang, Lihong; Huang, Xiaohua

2018-01-01

REEs in the environment can be absorbed by plants and sequestered by plant phytoliths. Acid rain can directly or indirectly affect plant physiological functions. Currently, the effects of REEs and acid rain on phytolith-REEs complex in plants are not yet fully understood. In this study, a high-silicon accumulation crop, rice (Oryza sativa L.), was selected as a representative of plants, and orthogonal experiments were conducted under various levels of lanthanum [La(III)] and pH. The results showed that various La(III) concentrations could significantly improve the efficiency and sequestration of phytolith La(III) in germinated rice seeds. A pH of 4.5 promoted phytolith La(III) sequestration, while a pH of 3.5 inhibited sequestration. Compared with the single treatment with La(III), the combination of La(III) and acid rain inhibited the efficiency and sequestration of phytolith La(III). Correlation analysis showed that the efficiency of phytolith La(III) sequestration had no correlation with the production of phytolith but was closely correlated with the sequestration of phytolith La(III) and the physiological changes of germinated rice seeds. Phytolith morphology was an important factor affecting phytolith La(III) sequestration in germinated rice seeds, and the effect of tubes on sequestration was more significant than that of dumbbells. This study demonstrated that the formation of the phytolith and La(III) complex could be affected by exogenous La(III) and acid rain in germinated rice seeds. PMID:29763463

Energy transfer driven tunable emission of Tb/Eu co-doped lanthanum molybdate nanophosphors

Science.gov (United States)

Thomas, Kukku; Alexander, Dinu; Sisira, S.; Gopi, Subash; Biju, P. R.; Unnikrishnan, N. V.; Joseph, Cyriac

2018-06-01

Tb3+/Eu3+ co-doped lanthanum molybdate nanophosphors were synthesized by conventional co-precipitation method. The Powder X-ray diffractogram revealed the formation of highly crystalline tetragonal nanocrystals with space group I41/a and the detailed analysis of the small variation of lattice parameters with Tb/Eu co-doping on the host lattice were carried out based on the ionic radii of the dopants. The FTIR spectra is employed to identify the fundamental vibrational modes in La2-x-y (MoO4)3:xTb, yEu nanocrystals. The formation of nanocrystals by oriented attachment was recognized from the HR TEM images and the d-spacing calculated was in accordance with that corresponding to highest intensity diffraction peak in the XRD patterns. The constituent elements present in the samples were identified with the aid of EDAX and elemental mapping analysis. The broad Mo6+- O2- CTB and the sharp excitation peaks of Tb and Eu identified from the UV-Vis absorption spectra facilitates the suitability of exciting the phosphors effectively over NUV and visible region of the spectra. The possibility of energy transfer from host to Tb3+/Eu3+ ions and from Tb3+ to Eu3+ ions were confirmed from the PL excitation spectra monitoring 5D0→7F2 transition of Eu3+ ions around 615 nm. The correlated analysis of PL emission spectra, life time measurements and CIE diagram, upon different excitation channels elucidate the excellent luminescent properties of La2-x-y (MoO4)3:xTb, yEu nanophosphors with tunable emission colours in a wide range varying from yellow green region to reddish orange region and the efficient energy transfer from Tb3+ to Eu3+ ions in lanthanum molybdate host lattice. The Tb→Eu energy transfer efficiency and probability were calculated from the decay measurements and the values were found to be satisfactory for exploiting the prepared nanophosphors for the development of multifunctional luminescent nanophosphors.

Lanthanum hexaboride as advanced structural refiner/getter in TiAl-based refractory intermetallics

Energy Technology Data Exchange (ETDEWEB)

Kartavykh, A.V., E-mail: karta@korolev-net.ru [Technological Institute for Superhard and Novel Carbon Materials (TISNCM), 7a Centralnaya str., 142190 Troitsk, Moscow (Russian Federation); National University of Science and Technology “MISIS”, Leninsky pr. 4, 119049 Moscow (Russian Federation); Asnis, E.A.; Piskun, N.V.; Statkevich, I.I. [The E.O. Paton Electric Welding Institute, 11 Bozhenko str., 03680 Kyiv (Ukraine); Gorshenkov, M.V.; Tcherdyntsev, V.V. [National University of Science and Technology “MISIS”, Leninsky pr. 4, 119049 Moscow (Russian Federation)

2014-03-05

Highlights: • Fist application of LaB{sub 6} additive in TiAl-based intermetallics casting. • Pilot synthesis/casting and study of selected TiAl(Nb,Cr,Zr)B,La alloys set. • Dual effect observed: phase structure refinement and oxygen impurity removal. • Co-precipitation of TiB and La{sub 2}O{sub 3} in melt: 2LaB{sub 6} + 12Ti + 3O → 12TiB↓ + La{sub 2}O{sub 3}↓. • Features of structure refinement and oxygen gettering mechanisms reported. -- Abstract: The work is aimed at the study of the formation and refinement of microstructure appearing in the solidifying refractory TiAl-based intermetallics being inoculated with precise boron addition. The novelty of research consists in test application of lanthanum hexaboride (LaB{sub 6}) ligature within semi-continuous electron beam casting process of selected alloys. Two ingots with nominal compositions Ti–44Al–5Nb–2Cr–1.5Zr–0.4B–0.07La and Ti–44Al–5Nb–1Cr–1.5Zr–1B–0.17La (at.%) have been synthesized and cast along with the reference alloy Ti–44Al–5Nb–3Cr–1.5Zr. Their comparative examination suggests (i) essential microstructural phase refinement effect coupled with (ii) threefold/fourfold decrease of background content of undesirable residual oxygen impurity in both alloys containing LaB{sub 6}. This advanced dual activity (i–ii) of LaB{sub 6} is explained by its complete dissolution, dissociation and following re-precipitation of effective Ti-based monoboride nucleants of orthorhombic B27 structure, those being accompanied by strong internal gettering of dissolved oxygen from the melt and from boride-inoculated solid α{sub 2}-Ti{sub 3}Al phase with liberated elemental lanthanum. The phase composition and structure of cast alloys; state and characterization of newly precipitated TiB boride; features of La{sub 2}O{sub 3} micro/nano-dimensional precipitation and oxygen gettering mechanism are reported and discussed.

Structural stability of the smectite-doped lanthanum under high pressures and high temperatures

International Nuclear Information System (INIS)

Stefani, Vicente Fiorini

2012-01-01

Smectites are phyllosilicates that have a tetrahedron: octahedron structure ratio of 2:1, with high cation exchange capacity (CEC) in the interlayers. For these and other features, smectites have been used in many parts of the world as secondary barriers with the goal of containing a possible leak of radioactive elements in final disposal facilities for radioactive waste through cation exchange. Our aim in this work is to reach the cation exchange in calcium montmorillonite (smectite dioctahedral) by lanthanum to simulate trivalent radionuclides and to study the stability of this structure under high pressure and high temperature. To achieve high pressure it was used two different technique: DAC (Diamond Anvil Cell), achieving pressures up to 12GPa at room temperature and hydraulic press with a toroidal chamber profile to achieve pressures up to 7,7GPa and temperatures up to 900 degree C. The heating is achieved simultaneously by an electric system coupled in the hydraulic press. The outcomes show that the smectite structure doped with lanthanum remains stable under 12GPa at room temperature and 2.5GPa at 200 degree C. However, above 300 degree C at 2.5GPa the structure becomes a new phase of muscovite-like, rich of La, where it loses its interlayer water and turns out to be irreversible. Furthermore, it is important to point out that the higher temperature the better ordered is the structure and it is still stable under 7.7GPa and 900 degree C. Moreover, after all experiments the structure continues being dioctahedral. The new phase of muscovite-like, rich of La, in contact with a calcium solution remains partially unchanged, whereas the other part returns to the original structure (montmorillonite-Ca). The following analyses were performed: X-ray diffraction (XRD) for evaluating the spatial structure; Fourier transform infrared spectroscopy (FTIR) for getting information about the vibrational modes; scanning electron microscopy with dispersive Xray spectroscopy

Carbon doped lanthanum aluminate (LaAlO{sub 3}:C) UV thermoluminescent properties synthesized by solid state reaction with three different mixing methodologies

Energy Technology Data Exchange (ETDEWEB)

Alves, N., E-mail: neire.radiologia@yahoo.com.br, E-mail: farialo@cdtn.br [Universidade Federal do Estado de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Departamento de Engenharia Nuclear; Ferraz, W.B.; Faria, L.O., E-mail: ferrazw@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

In this work we discuss the thermoluminescent (TL) response for LaAlO{sub 3}:C crystals grown by using three different combinations of Al{sub 2}O{sub 3}, La{sub 2}O{sub 3} and carbon atoms during the synthesis process. Recently, LaAlO{sub 3} single crystals, co-doped with Ce{sup 3+} and Dy{sup 3+} rare earth trivalent ions and grown under hydrothermal conditions, have been reported to show high thermoluminescent response (TL) when exposed to low levels of ultraviolet radiation (UVR). However, undoped LaAlO{sub 3} synthesized by solid state reaction method from the 1:1 mixture of aluminum and lanthanum oxide under reducing atmosphere revealed to have still higher thermoluminescent sensitivity to UV photon fields than the co-doped with Ce{sup 3+} and Dy{sup 3+}. It is well known that carbon doped aluminum oxide monocrystals have excellent TL and photoluminescent response properties for X-rays, UV and gamma radiation fields. Thus, we conducted three different syntheses of LaAlO{sub 3} by the solid state reaction method, doping the mixture with carbon. The lanthanum aluminate polycrystals were synthesized from the 1:1 mixture of aluminum and lanthanum oxide, adding 0.1wt.% carbon and annealed at 1700°C for two hours in hydrogen atmosphere. The X-ray diffraction analysis revealed the formation of rhombohedral LaAlO{sub 3} crystallographic phase, however a small percentage (15%) of Al{sub 2}O{sub 3} has been also identified. The UV-Vis absorbance spectra were obtained and F and F{sup +}- center were ascribed. The UV irradiations were carried out using a commercial 8W UV lamp. Thermoluminescence measurements were performed at a Harshaw 4500 TL reader. All compositions investigated have shown high TL sensitivity to UVR. (author)

Antisense oligonucleotides suppress cell-volume-induced activation of chloride channels.

Science.gov (United States)

Gschwentner, M; Nagl, U O; Wöll, E; Schmarda, A; Ritter, M; Paulmichl, M

1995-08-01

Cell volume regulation is an essential feature of most cells. After swelling in hypotonic media, the simultaneous activation of potassium and chloride channels is believed to be the initial, time-determining step in cell volume regulation. The activation of both pathways is functionally linked and enables the cells to lose ions and water, subsequently leading to cell shrinkage and readjustment of the initial volume. NIH 3T3 fibroblasts efficiently regulate their volume after swelling and bear chloride channels that are activated by decreasing extracellular osmolarity. The chloride current elicited in these cells after swelling is reminiscent of the current found in oocytes expressing an outwardly rectifying chloride current termed ICln. Introduction of antisense oligodeoxynucleotides complementary to the first 30 nucleotides of the coding region of the ICln channel into NIH 3T3 fibroblasts suppresses the activation of the swelling-induced chloride current. The experiments directly demonstrate an unambiguous link between a volume-activated chloride current and a cloned protein involved in chloride transport.

Resistance of Alkali-Activated Slag Concrete to Chloride-Induced Corrosion

Directory of Open Access Journals (Sweden)

Joon Woo Park

2015-01-01

Full Text Available The corrosion resistance of steel in alkali-activated slag (AAS mortar was evaluated by a monitoring of the galvanic current and half-cell potential with time against a chloride-contaminated environment. For chloride transport, rapid chloride penetration test was performed, and chloride binding capacity of AAS was evaluated at a given chloride. The mortar/paste specimens were manufactured with ground granulated blast-furnace slag, instead of Portland cement, and alkali activators were added in mixing water, including Ca(OH2, KOH and NaOH, to activate hydration process. As a result, it was found that the corrosion behavior was strongly dependent on the type of alkali activator: the AAS containing the Ca(OH2 activator was the most passive in monitoring of the galvanic corrosion and half-cell potential, while KOH, and NaOH activators indicated a similar level of corrosion to Portland cement mortar (control. Despite a lower binding of chloride ions in the paste, the AAS had quite a higher resistance to chloride transport in rapid chloride penetration, presumably due to the lower level of capillary pores, which was ensured by the pore distribution of AAS mortar in mercury intrusion porosimetry.

Chloride binding site of neurotransmitter sodium symporters

DEFF Research Database (Denmark)

Kantcheva, Adriana Krassimirova; Quick, Matthias; Shi, Lei

2013-01-01

Neurotransmitter:sodium symporters (NSSs) play a critical role in signaling by reuptake of neurotransmitters. Eukaryotic NSSs are chloride-dependent, whereas prokaryotic NSS homologs like LeuT are chloride-independent but contain an acidic residue (Glu290 in LeuT) at a site where eukaryotic NSSs...

The production of grain oriented lanthanum titanate (La2Ti2O7) ceramics by uniaxial hot-forging process for improved fracture toughness

International Nuclear Information System (INIS)

Ceylan, Ali

2008-01-01

The layered-structural ceramics, such as lanthanum titanate (La 2 Ti 2 O 7 ), have been known for their good electrical and optical properties at high frequencies and temperatures. However, few studies have been conducted on the mechanical properties of these ceramics. The interest in ceramic hot-forging (HF) has been greatly increased recently due to the enhancement in fracture toughness via bridging effect of oriented grains. In this study, grain oriented lanthanum titanate was produced by the hot-forging process. The characterizations of the samples were achieved by density measurement, scanning electron microscopy (SEM), optical microscopy, X-ray diffraction (XRD), Vickers indentation and three-point bending test. According to X-ray diffraction patterns, the orientation factor (f) was found to be 0.73 for certain hot-forging conditions resulting an improved fracture toughness. The improved fracture toughness of La 2 Ti 2 O 7 (3.2 MPa m 1/2 ) reached to the value of monolithic alumina (Al 2 O 3 ) between 3 and 4 MPa m 1/2

Catalytic Conversion of Cellulose to Levulinic Acid by Metal Chlorides

Directory of Open Access Journals (Sweden)

Beixiao Zhang

2010-08-01

Full Text Available The catalytic performance of various metal chlorides in the conversion of cellulose to levulinic acid in liquid water at high temperatures was investigated. The effects of reaction parameters on the yield of levulinic acid were also explored. The results showed that alkali and alkaline earth metal chlorides were not effective in conversion of cellulose, while transition metal chlorides, especially CrCl3, FeCl3 and CuCl2 and a group IIIA metal chloride (AlCl3, exhibited high catalytic activity. The catalytic performance was correlated with the acidity of the reaction system due to the addition of the metal chlorides, but more dependent on the type of metal chloride. Among those metal chlorides, chromium chloride was found to be exceptionally effective for the conversion of cellulose to levulinic acid, affording an optimum yield of 67 mol % after a reaction time of 180 min, at 200 °C, with a catalyst dosage of 0.02 M and substrate concentration of 50 wt %. Chromium metal, most of which was present in its oxide form in the solid sample and only a small part in solution as Cr3+ ion, can be easily separated from the resulting product mixture and recycled. Finally, a plausible reaction scheme for the chromium chloride catalyzed conversion of cellulose in water was proposed.

On barium oxide solubility in barium-containing chloride melts

International Nuclear Information System (INIS)

Nikolaeva, Elena V.; Zakiryanova, Irina D.; Bovet, Andrey L.; Korzun, Iraida V.

2016-01-01

Oxide solubility in chloride melts depends on temperature and composition of molten solvent. The solubility of barium oxide in the solvents with barium chloride content is essentially higher than that in molten alkali chlorides. Spectral data demonstrate the existence of oxychloride ionic groupings in such melts. This work presents the results of the BaO solubility in two molten BaCl 2 -NaCl systems with different barium chloride content. The received data together with earlier published results revealed the main regularities of BaO solubility in molten BaO-BaCl 2 -MCl systems.

Effects of Cations on Corrosion of Inconel 625 in Molten Chloride Salts

Science.gov (United States)

Zhu, Ming; Ma, Hongfang; Wang, Mingjing; Wang, Zhihua; Sharif, Adel

2016-04-01

Hot corrosion of Inconel 625 in sodium chloride, potassium chloride, magnesium chloride, calcium chloride and their mixtures with different compositions is conducted at 900°C to investigate the effects of cations in chloride salts on corrosion behavior of the alloy. XRD, SEM/EDS were used to analyze the compositions, phases, and morphologies of the corrosion products. The results showed that Inconel 625 suffers more severe corrosion in alkaline earth metal chloride molten salts than alkaline metal chloride molten salts. For corrosion in mixture salts, the corrosion rate increased with increasing alkaline earth metal chloride salt content in the mixture. Cations in the chloride molten salts mainly affect the thermal and chemical properties of the salts such as vapor pressure and hydroscopicities, which can affect the basicity of the molten salt. Corrosion of Inconel 625 in alkaline earth metal chloride salts is accelerated with increasing basicity.

Bone marrow scintigraphy with 111In-chloride

International Nuclear Information System (INIS)

Aburano, Tamio; Ueno, Kyoichi; Sugihara, Masami; Tada, Akira; Tonami, Norihisa

1977-01-01

It is assumed that 111 In-chloride is bound to serum transferrin and then transported into reticulocyte in erythropoietic marrow. However, several biochemical differences between radioiron and 111 In have been reported since these years. In present study, clinical usefulness of 111 In-chloride bone marrow scintigraphy was examined especially by comparing 111 In-chloride image with sup(99m)Tc-colloid. Obtained results are as follows: 1) In most cases, both 111 In-chloride and sup(99m)Tc-colloid images showed similar bone marrow distributions. 2) In three out of 7 cases with hypoplastic anemia and two patients with bone marrow irradiation (700-1,000 rad), the central marrow or irradiated marrow showed marked decreased uptake of 111 In, and showed normal uptake of sup(99m)Tc. 3) In two out of 3 cases with chronic myelogenous leucemia, central marrow showed normal uptake of 111 In, and showed decreased uptake of sup(99m)Tc. From the present study, the same dissociation findings as those between radioiron and radiocolloid could be obtained in hypoplastic anemia and bone marrow irradiation. 111 In-chloride would appear to be a useful erythropoietic imaging agent, although further study of exact comparison with radioiron should be necessary. (auth.)

Red, green, and blue lanthanum phosphate phosphors obtained via surfactant-controlled hydrothermal synthesis

International Nuclear Information System (INIS)

Sousa Filho, Paulo C. de; Serra, Osvaldo A.

2009-01-01

A new solution route for the obtainment of highly pure luminescent rare-earth orthophosphates in hydrothermal conditions was developed. By starting from soluble precursors (lanthanide tripolyphosphato complexes, i.e. with P 3 O 10 5- as a complexing agent and as an orthophosphate source) and by applying surfactants in a water/toluene medium, the precipitations are confined to reverse micelle structures, thus yielding nanosized and homogeneous orthophosphates. The method was employed to obtain lanthanide-activated lanthanum phosphates, which can be applied as red (LaPO 4 :Eu 3+ ), green (LaPO 4 :Ce 3+ ,Tb 3+ ) and blue (LaPO 4 :Tm 3+ ) phosphors. The produced materials were analyzed by powder X-ray diffractometry, scanning electron microscopy, infrared spectroscopy and luminescence spectroscopy (emission, excitation, lifetimes and chromaticity coordinates).

Electrodeposition behavior of nickel and nickel-zinc alloys from the zinc chloride-1-ethyl-3-methylimidazolium chloride low temperature molten salt

International Nuclear Information System (INIS)

Gou Shiping; Sun, I.-W.

2008-01-01

The electrodeposition of nickel and nickel-zinc alloys was investigated at polycrystalline tungsten electrode in the zinc chloride-1-ethyl-3-methylimidazolium chloride molten salt. Although nickel(II) chloride dissolved easily into the pure chloride-rich 1-ethyl-3-methylimidazolium chloride ionic melt, metallic nickel could not be obtained by electrochemical reduction of this solution. The addition of zinc chloride to this solution shifted the reduction of nickel(II) to more positive potential making the electrodeposition of nickel possible. The electrodeposition of nickel, however, requires an overpotential driven nucleation process. Dense and compact nickel deposits with good adherence could be prepared by controlling the deposition potential. X-ray powder diffraction measurements indicated the presence of crystalline nickel deposits. Non-anomalous electrodeposition of nickel-zinc alloys was achieved through the underpotential deposition of zinc on the deposited nickel at a potential more negative than that of the deposition of nickel. X-ray powder diffraction and energy-dispersive spectrometry measurements of the electrodeposits indicated that the composition and the phase types of the nickel-zinc alloys are dependent on the deposition potential. For the Ni-Zn alloy deposits prepared by underpotential deposition of Zn on Ni, the Zn content in the Ni-Zn was always less than 50 atom%

Fabrication of large-volume, low-cost ceramic lanthanum halide scintillators for gamma ray detection : final report for DHS/DNDO/TRDD project TA-01-SL01.

Energy Technology Data Exchange (ETDEWEB)

Boyle, Timothy J.; Ottley, Leigh Anna M.; Yang, Pin; Chen, Ching-Fong; Sanchez, Margaret R.; Bell, Nelson Simmons

2008-10-01

This project uses advanced ceramic processes to fabricate large, optical-quality, polycrystalline lanthanum halide scintillators to replace small single crystals produced by the conventional Bridgman growth method. The new approach not only removes the size constraint imposed by the growth method, but also offers the potential advantages of both reducing manufacturing cost and increasing production rate. The project goal is to fabricate dense lanthanum halide ceramics with a preferred crystal orientation by applying texture engineering and solid-state conversion to reduce the thermal mechanical stress in the ceramic and minimize scintillation light scattering at grain boundaries. Ultimately, this method could deliver the sought-after high sensitivity and <3% energy resolution at 662 keV of lanthanum halide scintillators and unleash their full potential for advanced gamma ray detection, enabling rapid identification of radioactive materials in a variety of practical applications. This report documents processing details from powder synthesis, seed particle growth, to final densification and texture development of cerium doped lanthanum bromide (LaBr{sub 3}:Ce{sup +3}) ceramics. This investigation demonstrated that: (1) A rapid, flexible, cost efficient synthesis method of anhydrous lanthanum halides and their solid solutions was developed. Several batches of ultrafine LaBr{sub 3}:Ce{sup +3} powder, free of oxyhalide, were produced by a rigorously controlled process. (2) Micron size ({approx} 5 {micro}m), platelet shape LaBr{sub 3} seed particles of high purity can be synthesized by a vapor phase transport process. (3) High aspect-ratio seed particles can be effectively aligned in the shear direction in the ceramic matrix, using a rotational shear-forming process. (4) Small size, highly translucent LaBr{sub 3} (0.25-inch diameter, 0.08-inch thick) samples were successfully fabricated by the equal channel angular consolidation process. (5) Large size, high density

Binding of rare earths to serum proteins and DNA

International Nuclear Information System (INIS)

Rosoff, B.; Spencer, H.

1979-01-01

In order to investigate further the physiological behavior of rare earths and rare earth chelates, studies of the binding of 46 Sc, 91 Y, and 140 La to serum proteins and to nucleic acids were performed using the methods of equilibrium dialysis and ultrafiltration. The binding of lanthanum and yttrium as the chlorides to α-globulin increased as the free rare earth concentration increased. When scandium and lanthanum were chelated in nitrilotriacetate (NTA) the binding to α-globulin was considerably less and there was no binding to albumin. The binding of 46 Sc chelated to ethylenediamine di(O-hydroxyphenylacetate) (EDDHA) was five times greater than of 46 Sc chloride. When the free scandium concentration was increased, the moles bound per mole of protein increased proportionally and the binding was reversible. Scandium was 100% filterable from a mixture of human serum and from the scandium chelates with high stability constants scandium diethylenetriaminepentaacetate (ScDTPA), scandium ethylenediaminetetraacetate (ScEDTA) and scandium cyclohexane trans-1,2-diaminetetraacetate (ScCDTA) respectively. In contrast, only 2% of the scandium was filterable when scandium nitrilotriacetate, a scandium chelate of low stability constant, was used. (Auth.)

Effect of ultrasound on electrochemical chloride extraction from mortar

Science.gov (United States)

Chen, Yiqun; Yao, Wu; Zuo, Junqing

2018-03-01

In this paper, the effect of auxiliary ultrasound on electrochemical chloride extraction (ECE) was studied. The chloride removal efficiency was investigated by examining the chloride content with ultrasound-assisted ECE and changing the introducing time of ultrasound. The experimental results showed that removal of chloride ions was noted to be more effective in ECE treatment assisted with ultrasound treatment (UT). In addition, the lower w/c ratio led to more distinct effect of ultrasonic cavitation on chloride removal. Electrochemical behaviors measured with different treatment revealed that UT treatment was effective on moderating the corrosion condition. Microstructural analyses revealed a significant alteration in composition and morphology of cementitious phases with UT treatment. Pull-out tests indicated that ultrasound had a certain negative impact on the bond strength. Although the effect of introducing ultrasound in the first 2 weeks or the last 2 weeks on the extraction efficiency was not obvious, intermittent ultrasound could not only ensure the chloride extraction efficiency, but also reduce the adverse effect of ultrasound on the bond strength.

Lanthanum titanium perovskite compound: Thin film deposition and high frequency dielectric characterization

Energy Technology Data Exchange (ETDEWEB)

Le Paven, C., E-mail: claire.lepaven@univ-rennes1.fr [Institut d' Electronique et de Télécommunications de Rennes (IETR, UMR-CNRS 6164), Equipe Matériaux Fonctionnels, IUT Saint Brieuc, Université de Rennes 1, 22000 Saint Brieuc (France); Lu, Y. [Institut d' Electronique et de Télécommunications de Rennes (IETR, UMR-CNRS 6164), Equipe Matériaux Fonctionnels, IUT Saint Brieuc, Université de Rennes 1, 22000 Saint Brieuc (France); Nguyen, H.V. [Institut d' Electronique et de Télécommunications de Rennes (IETR, UMR-CNRS 6164), Equipe Matériaux Fonctionnels, IUT Saint Brieuc, Université de Rennes 1, 22000 Saint Brieuc (France); CEA LETI, Minatec Campus, 38054 Grenoble (France); Benzerga, R.; Le Gendre, L. [Institut d' Electronique et de Télécommunications de Rennes (IETR, UMR-CNRS 6164), Equipe Matériaux Fonctionnels, IUT Saint Brieuc, Université de Rennes 1, 22000 Saint Brieuc (France); Rioual, S. [Laboratoire de Magnétisme de Brest (EA CNRS 4522), Université de Bretagne Occidentale, 29000 Brest (France); Benzegoutta, D. [Institut des Nanosciences de Paris (INSP, UMR CNRS 7588), Université Pierre et Marie Curie, 75005 Paris (France); Tessier, F.; Cheviré, F. [Institut des Sciences Chimiques de Rennes (ISCR, UMR-CNRS 6226), Equipe Verres et Céramiques, Université de Rennes 1, 35000 Rennes (France); and others

2014-02-28

Perovskite lanthanum titanium oxide thin films were deposited on (001) MgO, (001) LaAlO{sub 3} and Pt(111)/TiO{sub 2}/SiO{sub 2}/(001)Si substrates by RF magnetron sputtering, using a La{sub 2}Ti{sub 2}O{sub 7} homemade target sputtered under oxygen reactive plasma. The films deposited at 800 °C display a crystalline growth different than those reported on monoclinic ferroelectric La{sub 2}Ti{sub 2}O{sub 7} films. X-ray photoelectron spectroscopy analysis shows the presence of titanium as Ti{sup 4+} ions, with no trace of Ti{sup 3+}, and provides a La/Ti ratio of 1.02. The depositions being performed from a La{sub 2}Ti{sub 2}O{sub 7} target under oxygen rich plasma, the same composition (La{sub 2}Ti{sub 2}O{sub 7}) is proposed for the deposited films, with an unusual orthorhombic cell and Cmc2{sub 1} space group. The films have a textured growth on MgO and Pt/Si substrates, and are epitaxially grown on LaAlO{sub 3} substrate. The dielectric characterization displays stable values of the dielectric constant and of the losses in the frequency range [0.1–20] GHz. No variation of the dielectric constant has been observed when a DC electric field up to 250 kV/cm was applied, which does not match a classical ferroelectric behavior at high frequencies and room temperature for the proposed La{sub 2}Ti{sub 2}O{sub 7} orthorhombic phase. At 10 GHz and room temperature, the dielectric constant of the obtained La{sub 2}Ti{sub 2}O{sub 7} films is ε ∼ 60 and the losses are low (tanδ < 0.02). - Highlights: • Lanthanum titanium oxide films were deposited by reactive magnetron sputtering. • A La{sub 2}Ti{sub 2}O{sub 7} chemical composition is proposed, with an unusual orthorhombic cell. • At 10 GHz, the dielectric losses are lower than 0.02. • No variation of the dielectric constant is observed under DC electric biasing.

VOLATILE CHLORIDE PROCESS FOR THE RECOVERY OF METAL VALUES

Science.gov (United States)

Hanley, W.R.

1959-01-01

A process is presented for recovering uranium, iron, and aluminum from centain shale type ores which contain uranium in minute quantities. The ore is heated wiih a chlorinating agent. such as chlorine, to form a volatilized stream of metal chlorides. The chloride stream is then passed through granular alumina which preferentially absorbs the volatile uranium chloride and from which the uranium may later be recovered. The remaining volatilized chlorides, chiefly those of iron and aluminum, are further treated to recover chlorine gas for recycle, and to recover ferric oxide and aluminum oxide as valuable by-products.

Lanthanum gallate and ceria composite as electrolyte for solid oxide fuel cells

International Nuclear Information System (INIS)

Li Shuai; Li Zhicheng; Bergman, Bill

2010-01-01

The composite of doped lanthanum gallate (La 0.9 Sr 0.1 Ga 0.8 Mg 0.2 O 2.85 , LSGM) and doped ceria (Ce 0.8 Sm 0.2 O 1.9 , CSO) was investigated as an electrolyte for solid oxide fuel cell (SOFC). The LSGM-CSO composite was examined by X-ray diffraction (XRD) and impedance spectroscopy. It was found that the sintered LSGM-CSO composite contains mainly fluorite CeO 2 phase and a minority impurity phase, Sm 3 Ga 5 O 12 . The LSGM-CSO composite electrolyte shows a small grain boundary response in the impedance spectroscopy as compared to LSGM and CSO pellets. The composite electrolyte exhibits the highest conductivity in the temperature range of 250-600 o C, compared to LSGM and CSO. The LSGM-CSO composite can be expected to be an attractive intermediate temperature electrolyte material for solid oxide fuel cells.

Volatile mixed-ligand lanthanum (3) complex with acetylacetone and 1,10-phenanthroline

International Nuclear Information System (INIS)

Kuz'mina, N.P.; Chuparov, N.V.; Pisarevskij, A.P.; Martynenko, L.I.

1997-01-01

La(Acac) 3 Phen complex is synthetized, its X-tray structure analysis is carried out. Crystals are monoclinic ones, sp.gr. P2 1 /n, a=17.11 (12), b=18.16 (3), c=17.86 (2) A, β=91.32 (2) deg, V=5548 (13) A 3 , Z=8. Structure contains two crystallographically non-equivalent types of molecules differing in interatomic distances and valent angles, as well as, in angles between ligand planes. Behaviour of La(Acac) 3 Phen at heating in vacuum (0.1-0.01 mm Hg) is studied. It is shown that under those conditions processes of Phen splitting, of sublimation and polymerization of La(Acac) 3 lanthanum acetylacetonate formed following Phen splitting and that under 220 deg C during 30 min quantitative transition of La(Acac) 3 Phen into gas phase is reached. 10 refs., 2 figs., 3 tabs

Hydrocracking mechanisms in molten zinc chloride. Isotope scrambling and pyrolysis studies

International Nuclear Information System (INIS)

Larsen, J.W.; Earnest, S.

1979-01-01

Bruceton coal was hydrocracked in molten zinc chloride using H 2 -D 2 mixtures. No H-D was observed. The pyrolysis of Bruceton coal and a lignite in molten zinc chloride and an inert salt was carried out and the tetrahydrofuran and pyridine extractability of the products determined. In the absence of H 2 , zinc chloride is not an effective cracking catalyst. It is tentatively concluded that the catalytically active species is formed from zinc chloride and something in the coal and H 2 . The interactions between zinc chloride and the lignite appear to be significantly different than the interactions between zinc chloride and the bituminous coal. (Auth.)

Repassivation Potential of Alloy 22 in Sodium and Calcium Chloride Brines

International Nuclear Information System (INIS)

Rebak, R B; Ilevbare, G O; Carranza, R M

2007-01-01

A comprehensive matrix of 60 tests was designed to explore the effect of calcium chloride vs. sodium chloride and the ratio R of nitrate concentration over chloride concentration on the repassivation potential of Alloy 22. Tests were conducted using the cyclic potentiodynamic polarization (CPP) technique at 75 C and at 90 C. Results show that at a ratio R of 0.18 and higher nitrate was able to inhibit the crevice corrosion in Alloy 22 induced by chloride. Current results fail to show in a consistent way a different effect on the repassivation potential of Alloy 22 for calcium chloride solutions than for sodium chloride solutions

Two-electron oxidation of cobalt phthalocyanines by thionyl chloride: Implications for lithium/thionyl chloride batteries. Technical report

Energy Technology Data Exchange (ETDEWEB)

Bernstein, P.A.; Lever, A.B.

1989-10-20

Cyclic voltammetry, DPV and electronic spectroscopy are used to study the reaction between thionyl chloride and cobalt phthalocyanine. SOCl2 reacts with (Co(I)Tn Pc(2-)) and Co(II)Tn Pc(2-) to give two-electron oxidized species. Implications for Li/SOCl2 batteries are discussed. Thionyl chloride also forms a mono SOCl2 adduct with Co(II)TnPc(2-). Driving forces (Delta E values) were calculated for CoTnPc comproportionation and CoTnPc + SOCl2 reactions. Rest potential measurements of a Li/SOCl2 cells show that addition of AlCl3 stabilizes the LiCl product as LiAlCl4. A catalytic two-electron mechanism is indicated for the reduction of thionyl chloride in a Li/SOCl2/(CoTnPc,C) battery.

Advanced intermediate temperature sodium copper chloride battery

Science.gov (United States)

Yang, Li-Ping; Liu, Xiao-Min; Zhang, Yi-Wei; Yang, Hui; Shen, Xiao-Dong

2014-12-01

Sodium metal chloride batteries, also called as ZEBRA batteries, possess many merits such as low cost, high energy density and high safety, but their high operation temperature (270-350 °C) may cause several issues and limit their applications. Therefore, decreasing the operation temperature is of great importance in order to broaden their usage. Using a room temperature ionic liquid (RTIL) catholyte composed of sodium chloride buffered 1-ethyl-3-methylimidazolium chloride-aluminum chloride and a dense β″-aluminates solid electrolyte film with 500 micron thickness, we report an intermediate temperature sodium copper chloride battery which can be operated at only 150 °C, therefore alleviating the corrosion issues, improving the material compatibilities and reducing the operating complexities associated with the conventional ZEBRA batteries. The RTIL presents a high ionic conductivity (0.247 S cm-1) at 150 °C and a wide electrochemical window (-2.6 to 2.18 vs. Al3+/Al). With the discharge plateau at 2.64 V toward sodium and the specific capacity of 285 mAh g-1, this intermediate temperature battery exhibits an energy density (750 mWh g-1) comparable to the conventional ZEBRA batteries (728-785 mWh g-1) and superior to commercialized Li-ion batteries (550-680 mWh g-1), making it very attractive for renewable energy integration and other grid related applications.

Influence of La/W ratio on electrical conductivity of lanthanum tungstate with high La/W ratio

International Nuclear Information System (INIS)

Kojo, Gen; Shono, Yohei; Ushiyama, Hiroshi; Oshima, Yoshito; Otomo, Junichiro

2017-01-01

The proton-conducting properties of lanthanum tungstates (LWOs) with high La/W ratios were investigated using electrochemical measurements and quantum chemical calculations. Single phases of LWOs with high La/W ratios (6.3≤La/W≤6.7) were synthesized by high-temperature sintering at around 1700 °C. The electrical conductivity of LWO increased with increasing La/W ratio in the single-phase region. The LWO synthesized at the optimum sintering temperature and time, and with the optimum La/W ratio gave the maximum conductivity, i.e., 2.7×10 −3 S cm −1 with La/W=6.7 at 500 °C. Density functional theory calculations, using the nudged elastic band method, were performed to investigate the proton diffusion barrier. The results suggest that the proton diffusion paths around La sites have the lowest proton diffusion barrier. These findings improve our understanding of LWO synthesis and the proton-conducting mechanism and provide a strategy for improving proton conduction in LWOs. - Graphical abstract: The LWOs with high La/W ratios were synthesized for the first time. The optimum La/W ratio gave the maximum conductivity with La/W=6.7 at 500 °C. The proton diffusion paths were also considered with density functional theory calculations. - Highlights: • The proton-conducting properties of lanthanum tungstates (LWOs) were investigated. • Single phase LWOs with high La/W ratios (6.3≤La/W≤6.7) were synthesized successfully. • LWOs with the high La/W ratios showed high proton conductivity. • The DFT calculation suggested the lowest proton diffusion barrier in the path around La sites.

Radiation fixation of vinyl chloride in an insecticide aerosol container

International Nuclear Information System (INIS)

Kagiya, V.T.; Takemoto, K.

1975-01-01

Recently, a large quantity of vinyl chloride has been used as spraying additive for insecticide aerosols. Since January 1974 when the Food and Drug Administration of the United States of America announced that vinyl chloride causes liver cancer, it has been forbidden in Japan and the United States of America to market insecticide aerosol containers containing vinyl chloride. In Japan, following a government order, about 20 million insecticide aerosol containers have been collected and put into storage. A report is given on the radiation fixation of vinyl chloride as polyvinylchloride powder by gamma-ray-induced polymerization in the aerosol container. Insecticide aerosol containers containing vinyl chloride were irradiated by gamma rays from 60 Co at room temperature. Vinyl chloride polymerized to form powdered polymer in the container. Polymerization conversion increased with the irradiation dose, and after 10 Mrad irradiation, vinyl chloride was not found in the sprayed gas. This establishes that vinyl chloride can be fixed by gamma-ray irradiation in the aerosol container. To accelerate the reaction rate, the effect of various additives on the reaction was investigated. It was found that halogenated hydrocarbons, such as chloroform and carbon tetrachloride, accelerated the initiation of the polymerization, and that a vinyl monomer such as vinyl acetate accelerated the reaction rate due to the promotion of the initiation and the high reactivity of the polyvinylacetate radical to vinyl chloride. Consequently, the required irradiation dose for the fixation of vinyl chloride was decreased to less than 5 Mrad by the addition of various kinds of additives. Following the request of the Ministry of Public Welfare, various technical problems for large-scale treatment are being studied with the co-operation of the Federation of Insecticide Aerosols. (author)

Viscosity and density tables of sodium chloride solutions

Energy Technology Data Exchange (ETDEWEB)

Fair, J.A.; Ozbek, H. (comps.)

1977-04-01

A file is presented containing tabulated data extracted from the scientific literature on the density and viscosity of aqueous sodium chloride solutions. Also included is a bibliography of the properties of aqueous sodium chloride solutions. (MHR)

Determination of chloride in water. A comparison of three methods

International Nuclear Information System (INIS)

Steele, P.J.

1978-09-01

The presence of chloride in the water circuits of nuclear reactors, power stations and experimental rigs is undesirable because of the possibility of corrosion. Three methods are considered for the determination of chloride in water in the 0 to 10 μg ml -1 range. The potentiometric method, using a silver-silver chloride electrode, is capable of determining chloride above the 0.1μg ml -1 level, with a standard deviation of 0.03 to 0.12 μg ml -1 in the range 0.1 to 6.0 μg ml -1 chloride. Bromide, iodide and strong reducing agents interfere but none of the cations likely to be present has an effect. The method is very susceptible to variations in temperature. The turbidimetric method involves the production of suspended silver chloride by the addition of silver nitride solution to the sample. The method is somewhat unreliable and is more useful as a rapid, routine limit-testing technique. In the third method, chloride in the sample is pre-concentrated by co-precipitation on lead phosphate, redissolved in acidified ferric nitrate solution and determined colorimetrically by the addition of mercuric thiocyanate solution. It is suitable for determining chloride in the range 0 to 50 μg, using a sample volume of 100 to 500 ml. None of the chemical species likely to be present interferes. In all three methods, chloride contamination can occur at any point in the determination. Analyses should be carried out in conditions where airborne contamination is minimised and a high degree of cleanliness must be maintained. (author)

Corrosion Risk of Reinforced Concrete Structure Arising from Internal and External Chloride

Directory of Open Access Journals (Sweden)

M. J. Kim

2018-01-01

Full Text Available The corrosion risk of internal chloride and external chloride from three different exposure conditions was evaluated. The initiation of corrosion was detected by monitoring the galvanic current between cathode metal and embedded steel. The chloride threshold was determined by measuring the corrosion rate of steel by the polarization technique for internal chloride and the chloride profiling test for external chloride. As the result, the initiation of corrosion was accelerated with a cyclic wet/dry condition, compared to the totally wet condition. In addition, it was found that an increase of the drying ratio in the exposure condition resulted in an increase of corrosion rate after initiation. The threshold level of external chloride ranged from 0.2 to 0.3% weight by cement and internal chloride shows higher range, equated to 1.59–3.10%. Based on these data, the chloride penetration with exposure condition was predicted to determine the service life of reinforced concrete structure.

Structural, microstructural and transport properties study of lanthanum lithium titanium perovskite thin films grown by Pulsed Laser Deposition

International Nuclear Information System (INIS)

Maqueda, O.; Sauvage, F.; Laffont, L.; Martinez-Sarrion, M.L.; Mestres, L.; Baudrin, E.

2008-01-01

Lanthanum lithium titanate thin films were grown by Pulsed Laser Deposition. La 0.57 Li 0.29 TiO 3 dense films with smooth surfaces were obtained after optimization of the growth parameters. Such films deposited at 700 deg. C under 15 Pa are nano-crystalline with domains corresponding to the cubic and tetragonal modifications of this phase. In relation to the measured conductivities/activation energy and to previous works, we clearly underlined that the films of practical interest, prepared at relatively low temperature, are predominantly formed from the tetragonal ordered phase

Accelerated testing for chloride threshold of reinforcing steel in concrete

NARCIS (Netherlands)

Polder, R.B.; Put, M. van; Peelen, W.H.A.

2017-01-01

Testing for the chloride threshold (also called critical chloride content) for corrosion initiation of steel in concrete has been found difficult and, at best, time consuming. Nevertheless, the chloride threshold is an important parameter in service life design of new structures and for evaluation

Influence of lanthanum distribution on dielectric and ferroelectric properties of BaBi4-xLaxTi4O15 ceramics

International Nuclear Information System (INIS)

Khokhar, Anita; Goyal, Parveen K.; Thakur, O.P.; Shukla, A.K.; Sreenivas, K.

2015-01-01

Structural and electrical properties of Lanthanum substituted barium bismuth titanate BaBi 4-x La x Ti 4 O 15 (0 ≤ x ≤ 0.50) ceramics prepared by conventional solid-state reaction method have been investigated. Raman spectra reveals the distribution of lanthanum into the perovskite layers and (Bi 2 O 2 ) 2+ layers of BaBi 4 Ti 4 O 15 ceramics. Room temperature dielectric constant (ε′) increases and considerable reduction in the low frequency (10 −2 to 10 Hz) dielectric losses and in dc conductivity (σ dc ) are seen with lanthanum substitution. A critical La content of x ∼0.20 in BaBi 4-x La x Ti 4 O 15 exhibits a well-defined relaxor behavior as seen from the temperature and frequency dependence of the dielectric parameters ε′(T) and ε″(T). The dielectric data fit well to the modified Curie–Weiss law and the Lorentz-type relation and show increasing diffuseness in the phase transition with increasing La content. The temperature dependence of the characteristic relaxation time obtained from the Cole–Cole model shows a good fit to the non-linear Vogel–Fulcher relation. Improvements in the remnant polarization and a stable piezoelectric charge coefficient are seen up to a La content of x ∼0.20. The observed increase in dielectric loss and σ dc in addition to the diminished ferroelectric/piezoelectric properties for higher La content are explained in terms of changing oxygen vacancy concentration and structural relaxation due to the preferential incorporation of La into the (Bi 2 O 2 ) 2+ layers as evidenced through the Raman spectroscopy. - Highlights: • La distribution in BaBi 4-x La x Ti 4 O 15 ceramics is analyzed through Raman spectroscopy. • Low and a nearly constant loss over wide frequency range (10 −2 –10 7  Hz) obtained. • Critical La content x = 0.2 identified for high resistivity and ideal relaxor characteristics. • Improved P-E hysteresis loops and large remnant polarization measured. • Changes in the

The influence of lake water alkalinity and humic substances on particle dispersion and lanthanum desorption from a lanthanum modified bentonite.

Science.gov (United States)

Reitzel, Kasper; Balslev, Kristiane Astrid; Jensen, Henning S

2017-11-15

A 12 days laboratory study on potential desorption of Lanthanum (La) from a commercial La modified clay (Phoslock) was conducted using lake water from 17 Danish lakes with alkalinities between 0.02 and 3.7 meq L -1 and varying concentrations of DOC and humic acids (HA's). A similar study was conducted in artificial lake water with alkalinities from 0 to 2.5 meq L -1 in order to exclude interference from dissolved HA's. To test if La in solution (FLa) was associated with fine particles, the water samples were filtered sequentially through three filter sizes (1.2 μm, 0.45 μm and 0.2 μm), and finally, ultracentrifugation was used in an attempt to separate colloidal La from dissolved La. The study showed that higher FLa (up to 2.5 mg L -1 or 14% of the total La in the Phoslock) concentrations were found in soft water lakes compared to hard water lakes, probably due to dispersion of the clay at low alkalinities. In addition, this study showed that HA's seem to increase the FLa concentrations in soft water lakes, most likely through complexation of La retained in the Phoslock matrix. In summary, we conclude that elevated La concentrations in lake water after a Phoslock treatment should only be expected in soft water lakes rich in DOC and HA's. Copyright © 2017 Elsevier Ltd. All rights reserved.

High lumenal chloride in the lysosome is critical for lysosome function.

Science.gov (United States)

Chakraborty, Kasturi; Leung, KaHo; Krishnan, Yamuna

2017-07-25

Lysosomes are organelles responsible for the breakdown and recycling of cellular machinery. Dysfunctional lysosomes give rise to lysosomal storage disorders as well as common neurodegenerative diseases. Here, we use a DNA-based, fluorescent chloride reporter to measure lysosomal chloride in Caenorhabditis elegans as well as murine and human cell culture models of lysosomal diseases. We find that the lysosome is highly enriched in chloride, and that chloride reduction correlates directly with a loss in the degradative function of the lysosome. In nematodes and mammalian cell culture models of diverse lysosomal disorders, where previously only lysosomal pH dysregulation has been described, massive reduction of lumenal chloride is observed that is ~10 3 fold greater than the accompanying pH change. Reducing chloride within the lysosome impacts Ca 2+ release from the lysosome and impedes the activity of specific lysosomal enzymes indicating a broader role for chloride in lysosomal function.

Memory phenomenon in a lanthanum based bulk metallic glass

Energy Technology Data Exchange (ETDEWEB)

Zhou, Ye [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Huang, Wei Min, E-mail: mwmhuang@ntu.edu.sg [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Zhao, Yong [School of Chemistry and Chemical Engineering, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013 (China); Ding, Zhen [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Li, Yan [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Tor, Shu Beng; Liu, Erjia [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore)

2016-07-05

In this paper, we experimentally investigate two memory phenomena in a lanthanum based bulk metallic glass (BMG). While the temperature memory effect (TME) is not found by differential scanning calorimeter (DSC) test, shape recovery is observed in samples indented at both low and high temperatures. In terms of shape memory related characteristics, this BMG shares some features of shape memory alloys (SMAs) due to its metal nature, and some other features of shape memory polymers (SMPs) owing to its glassy–rubbery transition. The formation of protrusion in the polished sample after heating to super-cooled liquid region (SCLR) indicates that surface tension is not a necessarily positive contributor for shape recovery. Release of internal elastic stress is concluded as the major player. Although the amorphous nature of BMGs enables for storing appreciable amount of internal elastic stress upon deformation, without the presence of cross-linker as in typical SMPs, the shape recovery in BMGs is rather limited. - Highlights: • Experimental investigation of shape recovery in BMG. • Surface tension is not the major reason for shape recovery in BMG. • Release of internal stress is the major contributor for shape recovery. • Comparison of shape memory features of BMG with other shape memory materials.

Memory phenomenon in a lanthanum based bulk metallic glass

International Nuclear Information System (INIS)

Zhou, Ye; Huang, Wei Min; Zhao, Yong; Ding, Zhen; Li, Yan; Tor, Shu Beng; Liu, Erjia

2016-01-01

In this paper, we experimentally investigate two memory phenomena in a lanthanum based bulk metallic glass (BMG). While the temperature memory effect (TME) is not found by differential scanning calorimeter (DSC) test, shape recovery is observed in samples indented at both low and high temperatures. In terms of shape memory related characteristics, this BMG shares some features of shape memory alloys (SMAs) due to its metal nature, and some other features of shape memory polymers (SMPs) owing to its glassy–rubbery transition. The formation of protrusion in the polished sample after heating to super-cooled liquid region (SCLR) indicates that surface tension is not a necessarily positive contributor for shape recovery. Release of internal elastic stress is concluded as the major player. Although the amorphous nature of BMGs enables for storing appreciable amount of internal elastic stress upon deformation, without the presence of cross-linker as in typical SMPs, the shape recovery in BMGs is rather limited. - Highlights: • Experimental investigation of shape recovery in BMG. • Surface tension is not the major reason for shape recovery in BMG. • Release of internal stress is the major contributor for shape recovery. • Comparison of shape memory features of BMG with other shape memory materials.

Europium-Doped Lanthanum Hafnate Nanoparticles: Structure, Photoluminescence, and Radioluminescence

Science.gov (United States)

Wahid, Kareem; Pokhrel, Madhab; Mao, Yuanbing

Due to their novel physical properties, nanostructured phosphors are of interest for radiation-based imaging and therapeutics. Herein, the structural and luminescent properties of europium-doped lanthanum hafnate (La2Hf2O7:xmol%Eu3+, x = 0 - 35) nanoparticles are investigated for use as scintillators. X-ray diffraction, Raman spectroscopy, and scanning electron microscopy confirm samples prepared through a combined co-precipitation and low-temperature molten salt synthetic process homogenously form spherical nanocrystals of 36 nm in the ordered pyrochlore phase. Ultraviolet and X-ray excitation of these samples induce strong red emissions in the 580 - 590 and 612 - 630 nm range corresponding to the 5D0->7 F1 magnetic dipole and 5D0->7 F2 electric dipole transitions of Eu3+. Optical response and quantum yield are optimized at 5% Eu3+; a proposed trade-off between quenching mechanisms (defect-states/cross-relaxation) and dopant concentration is discussed. Owing to their high density, large effective atomic number, and bright luminescence, these La2Hf2O7:xmol%Eu3+ nanoparticles warrant further investigation for scintillator applications. The authors thank the support from the Defense Threat Reduction Agency of the U.S. Department of Defense (award #HDTRA1- 10-1-0114).

Rare Earth Doped Lanthanum Calcium Borate Polycrystalline Red Phosphors

Directory of Open Access Journals (Sweden)

H. H. Xiong

2014-01-01

Full Text Available Single-phased Sm3+ doped lanthanum calcium borate (SmxLa2−xCaB10O19, SLCB, x=0.06 polycrystalline red phosphor was prepared by solid-state reaction method. The phosphor has two main excitation peaks located at 398.5 nm and 469.0 nm, which are nicely in accordance with the emitting wavelengths of commercial near-UV and blue light emitting diode chips. Under the excitation of 398.0 nm, the dominant red emission of Sm3+ in SLCB phosphor is centered at 598.0 nm corresponding to the transition of 4G5/2 → 6H7/2. The Eu3+ fluorescence in the red spectral region is applied as a spectroscopic probe to reveal the local site symmetry in the host lattice and, hence, Judd-Ofelt parameters Ωt  (t=2, 4 of Eu3+ in the phosphor matrix are derived to be 3.62×10-20 and 1.97×10-20 cm2, indicating a high asymmetrical and strong covalent environment around rare earth luminescence centers. Herein, the red phosphors are promising good candidates employed in white light emitting diodes (LEDs illumination.

Absorption media for irreversibly gettering thionyl chloride

Science.gov (United States)

Buffleben, George; Goods, Steven H.; Shepodd, Timothy; Wheeler, David R.; Whinnery, Jr., LeRoy

2002-01-01

Thionyl chloride is a hazardous and reactive chemical used as the liquid cathode in commercial primary batteries. Contrary to previous thinking, ASZM-TEDA.RTM. carbon (Calgon Corporation) reversibly absorbs thionyl chloride. Thus, several candidate materials were examined as irreversible getters for thionyl chloride. The capacity, rate and effect of temperature were also explored. A wide variety of likely materials were investigated through screening experiments focusing on the degree of heat generated by the reaction as well as the material absorption capacity and irreversibility, in order to help narrow the group of possible getter choices. More thorough, quantitative measurements were performed on promising materials. The best performing getter was a mixture of ZnO and ASZM-TEDA.RTM. carbon. In this example, the ZnO reacts with thionyl chloride to form ZnCl.sub.2 and SO.sub.2. The SO.sub.2 is then irreversibly gettered by ASZM-TEDA.RTM. carbon. This combination of ZnO and carbon has a high capacity, is irreversible and functions effectively above -20.degree. C.

Amperometric Sensor for Detection of Chloride Ions†

Science.gov (United States)

Trnkova, Libuse; Adam, Vojtech; Hubalek, Jaromir; Babula, Petr; Kizek, Rene

2008-01-01

Chloride ion sensing is important in many fields such as clinical diagnosis, environmental monitoring and industrial applications. We have measured chloride ions at a carbon paste electrode (CPE) and at a CPE modified with solid AgNO3, a solution of AgNO3 and/or solid silver particles. Detection limits (3 S/N) for chloride ions were 100 μM, 100 μM and 10 μM for solid AgNO3, solution of AgNO3 and/or solid silver particles, respectively. The CPE modified with silver particles is the most sensitive to the presence chloride ions. After that we approached to the miniaturization of the whole electrochemical instrument. Measurements were carried out on miniaturized instrument consisting of a potentiostat with dimensions 35 × 166 × 125 mm, screen printed electrodes, a peristaltic pump and a PC with control software. Under the most suitable experimental conditions (Britton-Robinson buffer, pH 1.8 and working electrode potential 550 mV) we estimated the limit of detection (3 S/N) as 500 nM. PMID:27873832

Amperometric Sensor for Detection of Chloride Ions.

Science.gov (United States)

Trnkova, Libuse; Adam, Vojtech; Hubalek, Jaromir; Babula, Petr; Kizek, Rene

2008-09-15

Chloride ion sensing is important in many fields such as clinical diagnosis, environmental monitoring and industrial applications. We have measured chloride ions at a carbon paste electrode (CPE) and at a CPE modified with solid AgNO₃, a solution of AgNO₃ and/or solid silver particles. Detection limits (3 S/N) for chloride ions were 100 μM, 100 μM and 10 μM for solid AgNO₃, solution of AgNO₃ and/or solid silver particles, respectively. The CPE modified with silver particles is the most sensitive to the presence chloride ions. After that we approached to the miniaturization of the whole electrochemical instrument. Measurements were carried out on miniaturized instrument consisting of a potentiostat with dimensions 35 × 166 × 125 mm, screen printed electrodes, a peristaltic pump and a PC with control software. Under the most suitable experimental conditions (Britton-Robinson buffer, pH 1.8 and working electrode potential 550 mV) we estimated the limit of detection (3 S/N) as 500 nM.

21 CFR 172.330 - Calcium pantothenate, calcium chloride double salt.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium pantothenate, calcium chloride double salt... FOOD FOR HUMAN CONSUMPTION Special Dietary and Nutritional Additives § 172.330 Calcium pantothenate, calcium chloride double salt. The food additive calcium chloride double salt of calcium pantothenate may...

Mutagenicity of vinyl chloride after metabolic activation

Energy Technology Data Exchange (ETDEWEB)

Rannug, U; Johansson, A; Ramel, C; Wachtmeister, C A

1974-01-01

Vinyl chloride has recently been shown to cause a malignant liver tumor disease in man after occupational exposure in PVC plants. This actualizes the problem of whether such hazards could be avoided or at least diminished in the future by a screening for mutagenicity of chemicals used in industries. The basis for such a screening procedure is the close correlation between carcinogenic and mutagenic effects of chemicals. Experiments with Salmonella bacteria showed that the carcinogenic hazard of vinyl chloride could have been traced by means of mutagenicity tests. The data indicate that vinyl chloride is not mutagenic per se but becomes mutagenic after a metabolic activation in the liver. 24 references, 1 figure, 4 tables.

Chloride Ingress in Concrete Cracks under Cyclic Loading

DEFF Research Database (Denmark)

Küter, André; Geiker, Mette Rica; Olesen, John Forbes

2005-01-01

was similar for both sets and the maximum crack width was kept constant throughout the exposure period by means of precracking and an external prestressed reinforcement. Chloride profiles after 40 days revealed a considerable increase in ingress towards the crack tip in contrast to data from the literature....... Preliminary investigations have been undertaken to quantify the effect of dynamic load application on the chloride ingress into concrete cracks. Specimens were designed allowing ingress of a chloride solution into a single crack of a saturated unreinforced mortar beam. One set of specimens was subjected...... to a load frequency of ten applications per minute and a second set to one application per hour simulating static cracks, however limiting the ingress hampering effects of autogenous healing and a possible dense precipitation on the crack faces. The averaged chloride exposure interval of the crack faces...

Denitrification of fertilizer wastewater at high chloride concentration

DEFF Research Database (Denmark)

Ucisik, Ahmed Süheyl; Henze, Mogens

Wastewater from fertilizer industry is characterized by high contents of chloride concentration, which normally vary between 60 and 76 g/l. Experiments with bilogical denitrification were performed in lab-scale "fill and draw" reactors with synthetic wastewater with chloride concentrations up to 77.......4 g/l. The results of the experiments showed that biological denitrification was feasible at the extreme environmental conditions prevailing in fertilizer wastewater. Stable continuous biological denitrfication of the synthetic high chloride wastewater was performed up to 77.4 g Cl/l at 37 degree C...

Lithium-thionyl chloride batteries - past, present and future

Energy Technology Data Exchange (ETDEWEB)

McCartney, J.F.; Lund, T.J.; Sturgeon, W.J.

1980-02-01

Lithium based batteries have the highest theoretical energy density of known battery types. Of the lithium batteries, the lithium-thionyl chloride electrochemistry has the highest energy density of those which have been reduced to practice. The characteristics, development status, and performance of lithium-thionyl chloride batteries are treated in this paper. Safety aspects of lithium-thionyl chloride batteries are discussed along with impressive results of hazard/safety tests of these batteries. An orderly development plan of a minimum family of standard cells to avoid a proliferation of battery sizes and discharge rates is presented.

Formation of mixed hydroxides in the thorium chloride-iron chloride-sodium hydroxide system

International Nuclear Information System (INIS)

Krivokhatskij, A.S.; Prokudina, A.F.; Sapozhnikova, T.V.

1976-01-01

The process of formation of mixed hydroxides in the system thorium chloride-iron chloride-NaOH was studied at commensurate concentrations of Th and Fe in solution (1:1 and 1:10 mole fractions, respectively) with ionic strength 0.3, 2.1, and 4.1, created with the electrolyte NaCl, at room temperature 22+-1degC. By the methods of chemical, potentiometric, thermographic, and IR-spectrometric analyses, it was shown that all the synthesized precipitates are mechanical mixtures of two phases - thorium hydroxide and iron hydroxide - and not a new hydrated compound. The formal solubility of the precipitates of mixed hydroxides was determined. It was shown that the numerical value of the formal solubility depends on the conditions of formation and age of the precipitates

Preparation and characterization of poly-(methacrylatoethyl trimethylammonium chloride-co-vinylbenzyl chloride-co-ethylene dimethacrylate monolith

Directory of Open Access Journals (Sweden)

Eko Malis

2015-05-01

Full Text Available A polymer monolithic column, poly-(methacrylatoethyltrimethylammonium chloride-co-vinylbenzyl chloride-co-ethylene dimethacrylate or poly-(MATE-co-VBC-co-EDMA was successfully prepared in the current study by one-step thermally initiated in situ polymerization, confined in a steel tubing of 0.5 mm i.d. and 1/16” o.d. The monoliths were prepared from methacrylatoethyltrimethylammonium chloride (MATE and vinylbenzyl chloride (VBC as monomer and ethylene dimethacrylate (EDMA as crosslinker using a binary porogen system of 1-propanol and 1,4-butanediol. The inner wall of steel tubing was pretreated with 3-methacryloxypropyl-trimethoxysilane (MAPS. In order to obtain monolith with adequate column efficiency and low flow resistance, some parameters such as total monomer concentration (%T and crosslinker concentration (%C were optimized. The morphology of this monolith was assessed by scanning electron microscopy (SEM. The properties of the monolithic column, such as permeability, binding capacity, and pore size distribution were also characterized in detail. From the results of the characterization of all monolith variation, monolith with %T 30 %C 50 and %T 35 %C 50 give the best characteristic. These monoliths have high permeability, adequate molecular recognition sites (represented with binding capacity value of over 20 mg/mL, and have over 80% flow through pores in their pore structure contribute to low flow resistance. The resulted monolithic columns have promising potential for dual mode liquid chromatography. MATE may contribute for anion-exchange while VBC may responsible for reversed-phase liquid chromatography.

VOCl as a Cathode for Rechargeable Chloride Ion Batteries.

Science.gov (United States)

Gao, Ping; Reddy, M Anji; Mu, Xiaoke; Diemant, Thomas; Zhang, Le; Zhao-Karger, Zhirong; Chakravadhanula, Venkata Sai Kiran; Clemens, Oliver; Behm, R Jürgen; Fichtner, Maximilian

2016-03-18

A novel room temperature rechargeable battery with VOCl cathode, lithium anode, and chloride ion transporting liquid electrolyte is described. The cell is based on the reversible transfer of chloride ions between the two electrodes. The VOCl cathode delivered an initial discharge capacity of 189 mAh g(-1) . A reversible capacity of 113 mAh g(-1) was retained even after 100 cycles when cycled at a high current density of 522 mA g(-1) . Such high cycling stability was achieved in chloride ion batteries for the first time, demonstrating the practicality of the system beyond a proof of concept model. The electrochemical reaction mechanism of the VOCl electrode in the chloride ion cell was investigated in detail by ex situ X-ray diffraction (XRD), infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The results confirm reversible deintercalation-intercalation of chloride ions in the VOCl electrode. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Local impermeant anions establish the neuronal chloride concentration

DEFF Research Database (Denmark)

Glykys, J; Dzhala, V; Egawa, K

2014-01-01

Neuronal intracellular chloride concentration [Cl(-)](i) is an important determinant of γ-aminobutyric acid type A (GABA(A)) receptor (GABA(A)R)-mediated inhibition and cytoplasmic volume regulation. Equilibrative cation-chloride cotransporters (CCCs) move Cl(-) across the membrane, but accumulat...

AlN powder synthesis via nitriding reaction of aluminum sub-chloride

Energy Technology Data Exchange (ETDEWEB)

Ohashi, T.; Nishida, T.; Sugiura, M. (Waseda Univ., Tokyo (Japan). Graduate School); Fuwa, A. (Waseda Univ., Tokyo (Japan))

1993-06-01

In order to obtain the pertinent properties of aluminium nitride in its sintered form, it is desirable to have powders of finer sizes with narrower size distribution and higher purity, thereby making the sintering processing easier and the final body denser. Instead of using sublimated aluminum tri-chloride vapor (AlCl3) as an aluminum source in the vapor phase nitriding reaction, the mixed aluminum chloride vapor consisted of aluminum tri-chloride, bi-chloride and mono-chloride are used in the reaction with ammonia at temperatures of 1000 and 1200K. The mixed chloride vapors are produced by reacting chlorine with molten aluminum at 1000 or 1200K under atmospheric pressure. The reaction of this mixed chloride vapor with ammonia is then experimentally investigated to study the aluminum nitride powder morphology. The aluminum nitride powders synthesized under various ammonia concentrations are characterized for size distribution, mean particle size and particle morphology. 24 refs., 8 figs., 2 tabs.

High lumenal chloride in the lysosome is critical for lysosome function

Science.gov (United States)

Chakraborty, Kasturi; Leung, KaHo; Krishnan, Yamuna

2017-01-01

Lysosomes are organelles responsible for the breakdown and recycling of cellular machinery. Dysfunctional lysosomes give rise to lysosomal storage disorders as well as common neurodegenerative diseases. Here, we use a DNA-based, fluorescent chloride reporter to measure lysosomal chloride in Caenorhabditis elegans as well as murine and human cell culture models of lysosomal diseases. We find that the lysosome is highly enriched in chloride, and that chloride reduction correlates directly with a loss in the degradative function of the lysosome. In nematodes and mammalian cell culture models of diverse lysosomal disorders, where previously only lysosomal pH dysregulation has been described, massive reduction of lumenal chloride is observed that is ~103 fold greater than the accompanying pH change. Reducing chloride within the lysosome impacts Ca2+ release from the lysosome and impedes the activity of specific lysosomal enzymes indicating a broader role for chloride in lysosomal function. DOI: http://dx.doi.org/10.7554/eLife.28862.001 PMID:28742019

Chloride Sources and Losses in Two Tile-Drained Agricultural Watersheds.

Science.gov (United States)

David, Mark B; Mitchell, Corey A; Gentry, Lowell E; Salemme, Ronald K

2016-01-01

Chloride is a relatively unreactive plant nutrient that has long been used as a biogeochemical tracer but also can be a pollutant causing aquatic biology impacts when concentrations are high, typically from rock salt applications used for deicing roads. Chloride inputs to watersheds are most often from atmospheric deposition, road salt, or agricultural fertilizer, although studies on agricultural watersheds with large fertilizer inputs are few. We used long-term (21 and 17 yr) chloride water quality data in two rivers of east-central Illinois to better understand chloride biogeochemistry in two agricultural watersheds (Embarras and Kaskaskia), the former with a larger urban land use and both with extensive tile drainage. During our sampling period, the average chloride concentration was 23.7 and 20.9 mg L in the Embarras and Kaskaskia Rivers, respectively. Annual fluxes of chloride were 72.5 and 61.2 kg ha yr in the Embarras and Kaskaskia watersheds, respectively. In both watersheds, fertilizer chloride was the dominant input (∼49 kg ha yr), with road salt likely the other major source (23.2 and 7.2 kg ha yr for the Embarras and Kaskaskia watersheds, respectively). Combining our monitoring data with earlier published data on the Embarras River showed an increase in chloride concentrations as potash use increased in Illinois during the 1960s and 1970s with a lag of about 2 to 6 yr to changes in potash inputs based on a multiple-regression model. In these agricultural watersheds, riverine chloride responds relatively quickly to potash fertilization as a result of tile-drainage. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Thermodynamic properties of molten mixtures of lithium, rubidium, cesium and beryllium chlorides

International Nuclear Information System (INIS)

Zarubitskij, O.G.; Podafa, B.P.; Dubovoj, P.G.

1982-01-01

e. m. f. in binary systems of beryllium chloride with rubidium and cesium chlorides were measured. Concentration dependences of thermodynamic functions (mixing entropy Gibbs free energy) of beryllium chloride in the systems as well as with the participation of lithium chloride were analysed

Potentiometric Determination of Free Chloride in Cement Paste – an ...

African Journals Online (AJOL)

... cement paste.16 The accuracy and reliability of this analytical technique has been checked against a certified reference material, Merck sodium chloride solution. Confidence levels (CL0.95), of 0.03 and relative standard deviations of 0.2 % for chloride were determined for ordinary Portland cement (OPC) chloride binding ...

Lanthanum gallate and ceria composite as electrolyte for solid oxide fuel cells

Energy Technology Data Exchange (ETDEWEB)

Li Shuai, E-mail: shuail@kth.s [Department of Materials Science and Engineering, School of Industrial Engineering and Management, Royal Institute of Technology, SE 10044 Stockholm (Sweden); Li Zhicheng [School of Materials Science and Engineering, Central South University, 410083 Changsha, Hunan (China); Bergman, Bill [Department of Materials Science and Engineering, School of Industrial Engineering and Management, Royal Institute of Technology, SE 10044 Stockholm (Sweden)

2010-03-04

The composite of doped lanthanum gallate (La{sub 0.9}Sr{sub 0.1}Ga{sub 0.8}Mg{sub 0.2}O{sub 2.85}, LSGM) and doped ceria (Ce{sub 0.8}Sm{sub 0.2}O{sub 1.9}, CSO) was investigated as an electrolyte for solid oxide fuel cell (SOFC). The LSGM-CSO composite was examined by X-ray diffraction (XRD) and impedance spectroscopy. It was found that the sintered LSGM-CSO composite contains mainly fluorite CeO{sub 2} phase and a minority impurity phase, Sm{sub 3}Ga{sub 5}O{sub 12}. The LSGM-CSO composite electrolyte shows a small grain boundary response in the impedance spectroscopy as compared to LSGM and CSO pellets. The composite electrolyte exhibits the highest conductivity in the temperature range of 250-600 {sup o}C, compared to LSGM and CSO. The LSGM-CSO composite can be expected to be an attractive intermediate temperature electrolyte material for solid oxide fuel cells.

Gelcasting of strontium doped lanthanum manganite for solid oxide fuel cell applications

International Nuclear Information System (INIS)

Abdul Haleem, B.; Bhuvana, R.; Udayakumar, A.

2009-01-01

Solid oxide fuel cells (SOFCs) are devices that offer high efficiency power output with negligible emissions. Cathode supported tubular SOFCs consist of porous cathode tubes made up of strontium doped lanthanum manganite, La 1-x Sr x MnO 3 (LSM) that work as functional component as well as structural support for the rest of the cell components. Gelcasting is one of the most suitable methods for the fabrication of porous ceramics. This paper describes the fabrication of porous LSM cathode by gelcasting process. Gelcasting parameters such as monomer concentration, powder volume fraction, pH of the slurry, etc were optimized. Slow drying of green specimens minimized warpage and cracking. Sintered specimens with controlled porosity were obtained by the use of suitable pore-forming agents. The coefficient of thermal expansion (CTE) of sintered specimens was measured, which was found matching with the CTE values of cell components reported in the literature. These results have shown the suitability of the gelcast generated LSM cathodes for SOFC applications. (author)

Chloride transport in mortar at low moisture concentration

NARCIS (Netherlands)

Taher, A.; Zanden, van der A.J.J.; Brouwers, H.J.H.

2014-01-01

Chloride penetration into cementitious structures with a steel reinforcement results in corrosion of the steel. Concrete columns of bridges, which are in frequent contact with sea water, are an example of these structures. Understanding the chloride transport in cementitious materials can lead to

Suppression of cavitation in melted tungsten by doping with lanthanum oxide

International Nuclear Information System (INIS)

Yuan, Y.; Lu, G.H.; Xu, B.; Fu, B.Q.; Xu, H.Y.; Li, C.; Jia, Y.Z.; Qu, S.L.; Liu, W.; Greuner, H.; Böswirth, B.; Luo, G.-N.

2014-01-01

Melting and boiling behaviour of pure tungsten and 1 wt% lanthanum-oxide-doped tungsten (WL10) are investigated, focusing on the material selection with respect to material loss induced by cavitation. Melting experiments under high heat loads are carried out in the high heat flux facility GLADIS. Pulsed hydrogen neutral beams with heat flux of 10 and 23 MW m −2 are applied onto the adiabatically loaded samples for intense surface melting. Melt layer of the two tungsten grades exhibit different microstructure characteristics. Substantive voids owing to cavitation in the liquid phase are observed in pure W and lead to porous resolidified material. However, little cavitation bubbles can be found in the dense resolidified layer of WL10. In order to find out the gaseous sources, vapour collection is performed and the components are subsequently detected. Based on the observations and analyses, the microstructure evolutions corresponding to melting and vapourization behaviour of the two tungsten grades are tentatively described, and furthermore, the underlying mechanisms of cavitation in pure W and its suppression in WL10 are discussed. (paper)

Surface adsorption in strontium chloride ammines

DEFF Research Database (Denmark)

Ammitzbøll, Andreas L.; Lysgaard, Steen; Klukowska, Agata

2013-01-01

An adsorbed state and its implications on the ab- and desorption kinetics of ammonia in strontium chloride ammine is identified using a combination of ammonia absorption measurements, thermogravimetric analysis, and density functional theory calculations. During thermogravimetric analysis, ammonia...... desorption originating from the adsorbed state is directly observed below the bulk desorption temperature, as confirmed by density functional theory calculations. The desorption enthalpy of the adsorbed state of strontium chloride octa-ammine is determined with both techniques to be around 37-39 k...

Free and bound chloride contents in cementitious materials

NARCIS (Netherlands)

Marinescu, M.V.A.; Brouwers, H.J.H.; Fischer, G.; Geiker, M.; Hededal, O.; Ottoson, L.; Stang, H.

2010-01-01

Chloride attack is the main cause of structural damage in reinforced concrete buildings exposed to marine environments. When a certain threshold concentration of chlorides is reached at the concrete-reinforcement interface, the corrosion of the steel rebars is initiated. A part of the intruding

Chloride ion erosion experiment research in cracked concrete

Science.gov (United States)

Ting, Shu; Yang, Li

2017-08-01

For the study of chloride ion erosion in cracked concrete, this essay tries to take advantages of relevant trails to build up concrete chloride ion diffusion model based on the Fick’s second law. The parameter of this model is easy to be set, and many factors such as the effect of cracks are taken into consideration in this experiment. The concept of “chloride ion diffusion coefficient of equivalent apparent” is introduced to simplify the calculation. It can help simplify the calculation process, and get a more accurate test result, as well as facilitating the practical application of this parameter.

separation of strontium and cesium from ternary and quaternary lithium chloride-potassium chloride salts via melt crystallization

Directory of Open Access Journals (Sweden)

Ammon N. Williams

2015-12-01

Full Text Available Separation of cesium chloride (CsCl and strontium chloride (SrCl2 from the lithium chloride-potassium chloride (LiCl-KCl salt was studied using a melt crystallization process similar to the reverse vertical Bridgeman growth technique. A ternary SrCl2-LiCl-KCl salt was explored at similar growth rates (1.8–5 mm/h and compared with CsCl ternary results to identify similarities. Quaternary experiments were also conducted and compared with the ternary cases to identify trends and possible limitations to the separations process. In the ternary case, as much as 68% of the total salt could be recycled per batch process. In the quaternary experiments, separation of Cs and Sr was nearly identical at the slower rates; however, as the growth rate increased, SrCl2 separated more easily than CsCl. The quaternary results show less separation and rate dependence than in both ternary cases. As an estimated result, only 51% of the total salt could be recycled per batch. Furthermore, two models have been explored to further understand the growth process and separation. A comparison of the experimental and modeling results reveals that the nonmixed model fits reasonably well with the ternary and quaternary data sets. A dimensional analysis was performed and a correlation was identified to semipredict the segregation coefficient.

Separation of strontium and cesium from ternary and quaternary lithium chloride-potassium chloride salts via melt crystallization

Energy Technology Data Exchange (ETDEWEB)

Williams, Ammon n.; Pack, Michael [Dept. of Mechanical and Nuclear Engineering, Virginia Commonwealth University, Richmond (United States); Phongikaroon, Spathorn [Dept. of Chemical and Materials Engineering and Nuclear Engineering Program, University of Idaho, Idaho Falls (United States)

2015-12-15

Separation of cesium chloride (CsCl) and strontium chloride (SrCl{sub 2}) from the lithium chloride-potassium chloride (LiCl-KCl) salt was studied using a melt crystallization process similar to the reverse vertical Bridgeman growth technique. A ternary SrCl2-LiCl-KCl salt was explored at similar growth rates (1.8-5 mm/h) and compared with CsCl ternary results to identify similarities. Quaternary experiments were also conducted and compared with the ternary cases to identify trends and possible limitations to the separations process. In the ternary case, as much as 68% of the total salt could be recycled per batch process. In the quaternary experiments, separation of Cs and Sr was nearly identical at the slower rates; however, as the growth rate increased, SrCl{sub 2} separated more easily than CsCl. The quaternary results show less separation and rate dependence than in both ternary cases. As an estimated result, only 51% of the total salt could be recycled per batch. Furthermore, two models have been explored to further understand the growth process and separation. A comparison of the experimental and modeling results reveals that the nonmixed model fits reasonably well with the ternary and quaternary data sets. A dimensional analysis was performed and a correlation was identified to semipredict the segregation coefficient.

Chloride ingress profiles measured by electron probe micro analysis

DEFF Research Database (Denmark)

Jensen, Ole mejlhede; Coats, Alison M.; Glasser, Fred P.

1996-01-01

Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA is demonst......Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA...... is demonstated to determine chloride ingress in cement paste on a micrometer scale. Potential chloride ingress routes such as cracks or the paste-aggregate interface may also be characterized by EPMA. Copyright (C) 1996 Elsevier Science Ltd...

A study on dehydration of rare earth chloride hydrate

International Nuclear Information System (INIS)

Cho, Yong Zun; Eun, Hee Chul; Son, Sung Mo; Lee, Tae Kyo; Hwang, Taek Sung

2012-01-01

The dehydration schemes of rare earth (La, Ce, Nd, Pr, Sm. Eu, Gd, Y) chloride hydrates was investigated by using a dehydration apparatus. To prevent the formation of the rare earth oxychlorides, the operation temperature was changed step by step (80→150→230 degree C) based on the TGA (thermo-gravimetric analysis) results of the rare earth chloride hydrates. A vacuum pump and preheated Ar gas were used to effectively remove the evaporated moisture and maintain an inert condition in the dehydration apparatus. The dehydration temperature of the rare earth chloride hydrate was increased when the atomic number of the rare earth nuclide was increased. The content of the moisture in the rare earth chloride hydrate was decreased below 10% in the dehydration apparatus.

Amperometric Sensor for Detection of Chloride Ions

Directory of Open Access Journals (Sweden)

Rene Kizek

2008-09-01

Full Text Available Chloride ion sensing is important in many fields such as clinical diagnosis, environmental monitoring and industrial applications. We have measured chloride ions at a carbon paste electrode (CPE and at a CPE modified with solid AgNO3, a solution of AgNO3 and/or solid silver particles. Detection limits (3 S/N for chloride ions were 100 μM, 100 μM and 10 μM for solid AgNO3, solution of AgNO3 and/or solid silver particles, respectively. The CPE modified with silver particles is the most sensitive to the presence chloride ions. After that we approached to the miniaturization of the whole electrochemical instrument. Measurements were carried out on miniaturized instrument consisting of a potentiostat with dimensions 35 × 166 × 125 mm, screen printed electrodes, a peristaltic pump and a PC with control software. Under the most suitable experimental conditions (Britton-Robinson buffer, pH 1.8 and working electrode potential 550 mV we estimated the limit of detection (3 S/N as 500 nM.