WorldWideScience

Sample records for koseino kogyoro donyu

  1. FY 1998 survey report on the project on field tests for high-efficient industrial furnace introduction. Manual; 1998 nendo koseino kogyoro donyu field test jigyo mannual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The high-efficient industrial furnace is a technology with the use of ultra-high temperature air over 1,000 degrees C, which has been impossible. It has been developed since FY 1993. The technology can reduce the energy consumption amount by 30%, and there is a possibility of reducing not only CO2, but NOx by approximately 50% over the conventional method. The main technique of the technology is to preheat the air blown into the incinerator at much higher temperatures of 1,000 degrees C or more than those in the existing combustion and to blow fuel into that high-speed air flow using the short-time-change/heat-storage type heat exchanger. It was predicted that the target value set first can almost be reached, and there can be seen a possibility of its industrial application. Industrial furnaces are used in many industrial fields such as metal production industry, petrochemical industry and electric machinery industry. The energy conservation in these fields brings extremely marked effects, and therefore it is an urgent task to introduce the industrial furnace into the fields quickly. The concentrated R and D were finished in FY 1998, and the field test project for the introduction was actually started. (NEDO)

  2. Report on survey for high-performance industrial furnace introduction field test project in fiscal 1999. Verification work on achievements of industrial furnace development in 1999 by using theoretical method; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. 1999 nendo koseino kogyoro kaihatsu seika no rironteki shuho ni yoru kakusho gyomu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The high-performance industrial furnace introduction field test project has been executed from fiscal 1998 through fiscal 2000. Fiscal 1999 has performed measurements, evaluations, analyses, and follow-ups on representative demonstration furnaces, subsequently from fiscal 1998. At the same time, theoretical discussions were given to understand the details of the achievements. The measurements and investigations on the representative demonstration furnaces verified remarkable enhancement in the waste heat recovery rate, and noticeable reduction in the fuel unit requirement. In order to understand in-furnace phenomena and heat conduction mechanisms, simulations were made on combustion gas flows, combustion reactions, and heat conduction by using three-dimensional and non-steady state continuous analyses. The method used is an effective method to elucidate the in-furnace gas temperature distribution in terms of space and time, and evaluate the heat conducting performance quantitatively. The result obtained in the current fiscal year on the overall heat absorption rate was found to be about the same value as for conventional furnaces. The temperature efficiency calculation value for the heat recovering device was 90 to 95%, which is much higher than that for the conventional furnaces of 30 to 60%. The calculation value for the fuel unit requirement was also reduced by 20 to 30% from that of the conventional furnaces. The simulation result is effective in understanding the heat conduction performance enhancing mechanism, having been supplemented by the measurements. (NEDO)

  3. Survey report for fiscal 1999. Reference book for standard heat calculations in high-performance industrial furnace introduction field test project; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Hyojun netsu keisanshiki kijunsho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to verify in a short time the heat recovery capability being the evaluation parameter for the technologies to develop the high-performance industrial furnace, a standard calculation book will be prepared, which standardizes the data collection methods and heat calculation methods, and is used as the standard data sheets and bases. Evaluations and analyses will be given on business types, furnace constructions, thermal technologies, and functions in the research items adopted in the field test project. The results will be used to recognize the business entities engaged in the project in the next fiscal year, furnace types and sizes, establish the industrial furnace subjected to researches in the next fiscal year, and proliferate and expand the related business entities. Standard data sheets will be prepared on seven kinds of furnaces, heating furnaces (continuous and batch types), ladles, heat treatment furnaces (continuous and batch types), gas treatment furnaces, and melting furnaces. The standard data sheets will cover the following items: evaluation parameters (energy saving rate, thermal efficiency, and waste heat recovery rate), calculating conditions to be the base for the evaluation parameters, a heat production book to be the base for calculating the heat unit requirement, and a standard calculation book to be the base for the heat production table. The standard data sheets (including the standard calculation book) and floppy disks are submitted. (NEDO)

  4. Survey report for fiscal 1999. Evaluation and analysis on items applied for in high-performance industrial furnace introduction field test project in fiscal 1999; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Obo anken hyoka bunseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes comprehensive evaluation and analysis mainly on the 51 items adopted in the high-performance industrial furnace introduction field tests. The development of a high-performance industrial furnace has completed the fundamental development research in fiscal 1998, and the possibility was verified on energy saving of more than 30% and reduction of NOx emission by 50% over that by conventional furnaces. Upon this fundamental achievement, the field test project has started as the comprehensive approach to developing the practically usable technologies for three years from fiscal 1998 until fiscal 2000, which is being promoted as a joint research project. According to the survey on the actual state in fiscal 1998, a little less than 20,000 industrial furnaces having combustion capacity of more than 500,000 Kcal/hr (excepting boilers) are being used. If these furnaces are converted into the high-performance industrial furnace, energy conservation of 210,000 x 10{sup 6} Mcal (converted to crude oil of 22.7 x 10{sup 6} kl/year) can be achieved from the maximum annual energy consumption of 700,000 x 10{sup 6} Mcal (converted to crude oil of 75.7 x 10{sup 6} kl/year). This conservation amount corresponds to about 12% of the final energy consumption in the whole Japanese industrial departments in fiscal 1996. It is expected that the performance of the full-size high-performance industrial furnace will be verified, and this technology will be promoted for wide proliferation. (NEDO)

  5. Fiscal 1998 research report. Current state survey for promoting the field test project for introduction of advanced industrial furnaces; 1998 nendo koseino kogyoro donyu field test jigyo ni okeru jigyo sokushin no tame no jittai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Survey was made on the current state of installation and operation of industrial furnaces mainly in manufacturers to predict the applicability of advanced industrial furnaces, and study was made on energy consumption trends, the energy saving effect of advanced industrial furnaces, and factor extraction for their applicability. In the survey, questionnaires were delivered to 4,597 offices extracted from domestic 50,780 offices with employees more than 30, and nearly 30% of them were recovered, covering nearly 2.6% of all the offices concerned with this survey. As the survey result, the total annual energy consumption of domestic manufacturers was estimated to be 740,949 x 10{sup 6}Mcal, and among it, 709,709 x 10{sup 6}Mcal for large industrial furnaces. Under the assumption that nearly 30% of large industrial furnaces in operation are replaced with advanced industrial furnaces, energy saving expectation is estimated to be 210,000 x 10{sup 6}Mcal. Opinions and demands for this project showed the difficulty in their application to industrial furnaces in operation and study on their effects. Further enlightenment activities are necessary. (NEDO)

  6. FY 1998 Report on field test project study for introduction of high-performance industrial furnaces. Detailed measurement study of FY 1998 joint research demonstration data; Koseino kogyoro donyu field test jigyo. 1998 nendo kyodo kenkyu jissho data no shosaina sokutei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are the FY 1998 results of measurement and study for introduction of the high-performance industrial furnaces. The NEDO's works for development of the high-performance industrial furnaces have been almost completed. The field tests are conducted to verify leveling and increasing temperature in the high-performance industrial furnaces. The data are collected in the existing and modified furnaces at the standard treating rate for each of the selected furnaces. The measured items are heat patterns of the works, temperature distributions within the furnace, heat balances in the combustion furnace, waste heat at the regenerative heat recovery unit, and exhaust gas components. The investigated items are names, materials, shapes, weights and quantities of the works; charging/discharging temperature; heating time; temperature in each furnace; consumption, types and heating values of the fuels used; air/fuel ratios; presence or absence of recuperator and its conditions when adopted; air temperature upstream and downstream of the heat accumulator, and exhaust gas temperature and components; temperature of the heat accumulator's external walls; cooling water rates, and inlet/outlet temperature, surface temperature of the furnaces' external walls; and furnace dimensions and structures. The measurements are done by thermocouples for various types of temperature, and O{sub 2}, CO2, CO, NOx meters and other analyzers for the components. The data are collected on a continuous basis. (NEDO)

  7. Report on survey for high-performance industrial furnace introduction field test project in fiscal 1999. Activities to promote proliferation of the introduction to subject project related business entities; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Taisho jigyosha eno fukyu sokushin katsudo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper reports the survey on high-performance industrial furnace introduction field test project in fiscal 1999. The development of a high-performance industrial furnace having been performed by NEDO since fiscal 1993 has completed the fundamental development research in fiscal 1998, and the planned achievements were verified (large energy saving, reduction of NOx emission, and down-sizing). Upon the result, the introduction field test project has started in fiscal 1998 for three years until fiscal 2000. The number of research items adopted in fiscal 1998 was 58, and those in fiscal 1999 was 51, which are progressing smoothly at the present. Reduction in CO2 emission of 50,000 tons was demonstrated as the achievement in fiscal 1998, and NOx emission realized the regulation value or lower in cities wherein each operator is executing the project. Several cases of down-sizing were also reported. In the proliferation promoting project in fiscal 1998, activities were made mainly to the subject project related business entities in relation with the development achievements and general technologies for the high-performance furnace. In fiscal 1999, communication transmission was continued by using information tools on introduction of the achievements and technologies. Attempts will be made on promoting the proliferation of the field test project in the future through a number of technology lecture meetings performed by specialists. (NEDO)

  8. FY 2000 report on the survey of the project on field tests on the introduction of high performance industrial furnaces. Analysis/evaluation of the collected data; 2000 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Shushu data kaiseki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of achieving the target of reduction in CO2 regarded as substance causing global warming which was agreed at COP3, the study has been made since FY 1993 on 'the development of high performance industrial furnaces (regenerative combustion furnace using heat storage type burner for realization of high temperature air combustion).' By applying the good results obtained, a field test project for introduction of high performance industrial furnace has been implemented for three years (FY 1998 - FY 2000) to confirm the actual performance, reliability, etc. Collection/arrangement were made mainly of the data obtained in this field test project for the introduction of high performance industrial furnaces in each fiscal year (1998, 1999 and 2000), and verification/evaluation and arrangement were made. In this R and D, energy conservation was achieved at a rate of more than 30% of the target. Also about NOx, the result was obtained that the NOx by energy saving can be reduced 50% in almost all kinds of furnace if adding the reduction amount in emission amount and the reduction amount by high temperature air combustion. About the quality, the good result was obtained. Downsizing was conducted in approximately 10 examples. (NEDO)

  9. FY 2000 report on the survey of the project on field tests on the introduction of high performance industrial furnaces. Analysis/evaluation of the collected data; 2000 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Shushu data kaiseki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of achieving the target of reduction in CO2 regarded as substance causing global warming which was agreed at COP3, the study has been made since FY 1993 on 'the development of high performance industrial furnaces (regenerative combustion furnace using heat storage type burner for realization of high temperature air combustion).' By applying the good results obtained, a field test project for introduction of high performance industrial furnace has been implemented for three years (FY 1998 - FY 2000) to confirm the actual performance, reliability, etc. Collection/arrangement were made mainly of the data obtained in this field test project for the introduction of high performance industrial furnaces in each fiscal year (1998, 1999 and 2000), and verification/evaluation and arrangement were made. In this R and D, energy conservation was achieved at a rate of more than 30% of the target. Also about NOx, the result was obtained that the NOx by energy saving can be reduced 50% in almost all kinds of furnace if adding the reduction amount in emission amount and the reduction amount by high temperature air combustion. About the quality, the good result was obtained. Downsizing was conducted in approximately 10 examples. (NEDO)

  10. FY 1999 report on the results of the R and D on high performance industrial furnace, etc.; 1999 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the development of high performance industrial furnace, initial targets were achieved such as energy saving of 30%, downsizing of 20%, and a remarkable NOx reduction. To verify the achievement, the test field project is being worked on by NEDO. In FY 1998, 23 heating furnaces, 29 heat treat furnaces and 6 melting furnaces were under the project at energy saving effect of 52,000 kl converted to crude oil. In FY 1999, 18 heating furnaces, 26 heat treat furnaces and 7 melting furnaces are now under the project at energy saving effect of 57,000 kl. The project was awarded 'The 9th Nikkei Global Environmental Technology Prize.' The themes for the R and D are as follows: high efficiency exhaust heat utilization system, self-completion type high temperature/high radiation heating technology, technology to make heat transfer in steel heating suitable under non-stationary state, high efficiency heat transfer technology, technology to optimize the shape of heating furnace, high performance atmosphere heat treat furnace, high efficiency heat transfer technology by high temperature jet flame heating, technology of high efficiency aluminum melting furnace, technology to improve soaking degree in steel heating, high performance tubular heating furnace in oil refining, optimum combustion control technology of regenerative burner furnace, and laser measuring method inside industrial furnace. (NEDO)

  11. Fiscal 1998 research report on development of the advanced industrial furnace (R and D on the advanced industrial furnace). Volume 3; 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the research results of the chapter 4 and 5 (experimental database) from the research report on development of the advanced industrial furnace. The chapter 4 summarizes functions of the temperature performance evaluation simulator of the advanced continuous heating furnace for the database system, and various research results obtained by the simulator. This chapter also summarizes the research result on the applicability of high-temperature air combustion to other industries, the patent research result on heat storage combustion technology, the basic technology research result, and the reaction analysis result by FLUENT. The chapter 5 summarizes the combustion experiment data collection by developing self-completion high-temperature high-radiation heating technology. As for R and D on technology optimizing the profile of heating furnaces, the following data are summarized: measurement data of heat transfer in furnaces and heat flux data at right overhead furnace temperature under cold air and preheated air combustion in conventional furnaces, and heat storage combustion. (NEDO)

  12. FY 1993-1999 report on all the results of the development of high performance industrial furnace; Koseino kogyoro no kaihatsu sogo seika hokokusho (1993 - 1999 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Since an phenomenon was found out that NOx emission, which was thought to be increased, will be decreased by burning the high temperature preheated air jetting it at high speed (high temperature air combustion) in industrial furnace, there appeared a possibility of technical breakthrough for achieving the heightening of energy utilization efficiency and NOx reduction by exhaust heat recovery at the same time. This project aims at conducting full-scale experiments based on the basement technology including the theoretical elucidation of the combustion mechanism and high temperature air combustion by using various experimental facilities. Further, making full use of the most up-to-date analysis methods and constructing general-purpose database, the development is also aimed at of high performance industrial furnaces such as various heating furnace, heat treat furnace and melting furnace, with the assumption of prompt commercialization of the results of the development. As a result, targets were achieved such as energy saving of 30% or more, downsizing of 20% and a remarkable NOx reduction. Core technologies of this project are in-system limit heat recovery technology, high temperature air combustion technology, temperature field control technology (furnace temperature leveling technology) and high exergy heat transfer technology (furnace temperature heightening technology). (NEDO)

  13. Report on research results of the development of high efficient boilers in fiscal 1996. Research development of high efficient industrial furnaces, etc; Koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Out of the developments of high efficient boilers which have been continued since fiscal 1993, the paper reported the result of the development conducted in fiscal 1996. The oxygen combustion (the oxygen enrichment combustion including 100% oxygen combustion) decreases the amount of flue gas and reduces heat loss of the flue gas, and is also effective as NOx reduction measures. The experiment was conducted using testing furnace. The boiler efficiency rapidly increased with the increasing concentration of oxygen enrichment. In the pure oxygen combustion, the overall boiler efficiency of a 106% level (low heating value standard) is expected. Since the boiler wet flue gas is decreased, the NOx emission is reduced. The boiler can raise the combustion temperature with no fear of NOx and can be reduced in size. CO2 decreases in proportion to the energy saving effect. The development of a condensation flue gas heat exchanger is aimed at recovering heat down to the low temperature. Prediction of heat transfer in the steam condensation region becomes possible, and the size reduction can be expected. Dew point corrosion resistant materials were also selected. As to the high speed combustion control, a simple type using micro-processor was developed. Obtained were high speed, compactness, electric power saving, and high controllability. 14 refs., 306 figs., 88 tabs.

  14. FY 1999 achievement report on the development of high performance boilers. R and D on high performance industrial furnaces, etc.; 1999 nendo koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project started in FY 1993 to survey the actual state of industrial use boilers. Based on the results of the survey, in fiscal 1995, 1996 and 1997, no improvement of the present technology which has limits, but the development was made of the oxygen combustion and element technology which are factors for heightening boiler performance with a new idea first in the world. In fiscal 1998, a target for the overall thermal efficiency of 105% was settled by testing a pilot plant where the element technology was integrated into the small once-through boiler, flue/smoke tube boiler, water tube boiler, etc. In fiscal 1999, the target of the overall thermal efficiency of boiler was reached by a pilot plant test to clarify combustion characteristics, heat transfer characteristics, environmental characteristics, etc. Further, effects of energy saving were increased by the adoption method of oxygen supply equipment. Concretely, an overall boiler efficiency of 105.73% exceeding the targeted value of 105% was achieved at a pilot plant of actual scale, by concentrating the results of each of the element technologies such as 'oxygen combustion,' 'condensation type flue gas heat exchanger,' 'high performance combustion control device,' and 'rapid rotating auxiliary machine.' (NEDO)

  15. Research achievement report for fiscal 1998 on the development of high-performance industrial furnaces. Research and development of high-performance industrial furnaces and the like (2); 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu (2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Volume 2 named above contains part of research achievement reports and individual research achievement reports. The aluminum melting furnace working group research achievement report covers aluminum melting furnace operating patterns, concentrated impinging flame mode and dispersed impinging flame mode, and honeycomb and ball structures in heat storing bodies. The tubular heater working group report mentions the application of this facility to oil heating furnaces, studies and investigations for the embodiment of real systems using the tubular heater, and tests conducted in a furnace with plural heating tube lines. The individual research achievement reports elaborate on the development of technologies of heat transfer optimization under unsteady conditions in the steel material heating process, research and development of high-efficiency heat transfer technologies, development of heating furnace geometry optimization technologies, research and development of a high-performance controlled atmosphere heat treatment furnace, development of high-efficiency heat transfer technologies in high-temperature jet flame heating, development of heat uniformity improvement technologies for example for the steel material heating process, construction of optimum combustion control technologies for the regenerative burner furnace, research concerning laser-aided measurement in industrial furnaces, etc. (NEDO)

  16. Fiscal 1997 report on the results of the research on the development of high-performance industrial furnaces. R and D of high-performance industrial furnaces, etc; 1997 nendo seika hokokusho (koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho). Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A R and D was conducted for the purpose of developing remarkable energy conservation/CO2 reduction technologies. In fiscal 1997, the five working groups about the following were formed to have animated discussions: the basic research, heating furnace, heat treatment furnace, melting furnace, and tubular heating furnace. The research subjects are the pursuit/deepening of the base study on flame structures in high temperature air combustion, critical heat recovery of the system in high temperature air combustion, examination of the basic common technology on the ultimate optimization of the material heat transfer, construction of general-purpose experimental database, setting-up of design standards for general-purpose high-performance industrial furnaces, presentation of examples of the actual trial design based on the design standards and feasibility study of the practical application, preparatory support of the field test project on high-performance industrial furnaces for commercialization/diffusion/spread, etc. Further, how to arrange the developmental results was studied to make the results of the project useful for study of the prompt commercialization. 442 refs., 1444 figs., 311 tabs.

  17. Fiscal 1997 report on the results of the research on the development of high-performance industrial furnaces. Volume 2; 1997 nendo seika hokokusho (koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusto)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A R and D was conducted for the purpose of developing remarkable energy conservation/CO2 reduction technologies. In fiscal 1997, the five working groups about the following were formed to have animated discussions: the basic research, heating furnace, heat treatment furnace, melting furnace, and tubular heating furnace. The research subjects are the pursuit/deepening of the base study on flame structures in high temperature air combustion, critical heat recovery of the system in high temperature air combustion, examination of the basic common technology on the ultimate optimization of the material heat transfer, construction of general-purpose experimental database, setting-up of design standards for general-purpose high-performance industrial furnaces, presentation of examples of the actual trial design based on the design standards and feasibility study of the practical application, preparatory support of the field test project on high-performance industrial furnaces for commercialization/diffusion/spread, etc. Further, how to arrange the developmental results was studied to make the results of the project useful for study of the prompt commercialization. 442 refs., 1444 figs., 311 tabs

  18. Fiscal 1997 report on the results of the research on the development of high-performance industrial furnaces. Volume 3; 1997 nendo seika hokokusho (koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusto)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A R and D was conducted for the purpose of developing remarkable energy conservation/CO2 reduction technologies. In fiscal 1997, the five working groups about the following were formed to have animated discussions: the basic research, heating furnace, heat treatment furnace, melting furnace, and tubular heating furnace. The research subjects are the pursuit/deepening of the base study on flame structures in high temperature air combustion, critical heat recovery of the system in high temperature air combustion, examination of the basic common technology on the ultimate optimization of the material heat transfer, construction of general-purpose experimental database, setting-up of design standards for general-purpose high-performance industrial furnaces, presentation of examples of the actual trial design based on the design standards and feasibility study of the practical application, preparatory support of the field test project on high-performance industrial furnaces for commercialization/diffusion/spread, etc. Further, how to arrange the developmental results was studied to make the results of the project useful for study of the prompt commercialization. 442 refs., 1444 figs., 311 tabs.

  19. Reports on research achievements in developing high-performance industrial furnaces in fiscal 1998 (Research and development of high-performance industrial furnaces). Volume 1; 1998 nendo koseino kogyoro nado ni kansuru kenkyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    From the reports on research achievements in developing high-performance industrial furnaces in fiscal 1998, the report volume 1 was prepared as a research achievement report of each working group, detailing fundamental researches, heating furnaces, and heat treatment furnaces. The fundamental researches have researched combustion evaluating technology, characteristics of the area in the vicinity of a combustor, characteristics of combustion of high-temperature air, heating characteristics of a furnace to investigate effect of local heat absorption, and combustion evaluation. For the heating furnaces, the following subjects were studied: development of an in-furnace combustion model, summary of an experiment for evaluating high-temperature air combustion, furnace height relative to combustion heat transfer characteristics, heat loss minimizing technology, combustion heat transfer characteristics of liquid fuels, optimal operation of the high-temperature air combustion, basic control in heating control, and steel piece heating control. Studies were performed for the heat treatment furnaces on the case of a direct firing furnace in evaluating the heat transfer characteristics, the case of a radiant tube furnace, application of thermal fluid simulation technology, furnace averaging technology, soot reducing technology, control technology, and trial design on a high-performance heat treatment furnace. (NEDO)

  20. Report on research achievement in relation with developing fundamental combustion control technologies in fiscal 1998. Research and development of high-performance industrial furnaces; 1998 nendo nensho seigyo kiban gijutsu no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Development is intended to be made on fundamental combustion control technologies applicable to high-performance industrial furnaces that can reduce energy consumption and respond to environment preservation requirements. With an intention to achieve reduction in combustion exhaust gases such as carbon dioxide and nitrogen oxides, fundamental studies will be made on factors to decide flame shapes as represented by high-temperature combustion and flame shape control by utilizing microgravity environment, and researches will be made on combustion systems. Devices required for the experiments were fabricated to evaluate critical combustion characteristics of flames in furnaces including industrial furnaces, analyze and evaluate flame control parameters, and study low-pollution combustion technologies. Experimental methods acquired by 1997 were used for the experiments under the microgravity environment. Evaluation experiments were performed on flame shape control technologies and flame radiation characteristics, and basic experiments on the low-pollution combustion technologies. With these experiments, elucidation of the combustion mechanisms was launched by analyzing and evaluating the acquired data. A flame experimenting device for high-temperature preheated air completed by fiscal 1997 was used to acquire such combustion characteristics data as NOx discharge characteristics when the high-temperature preheated air is used. Based on the result thereof, verification was carried out on simulation models. (NEDO)

  1. Advanced `KS-6` dry type lubricant for aluminum sheet forming; Arumi ban seikeiyo koseino kokei junkatsuzai `KS-5`

    Energy Technology Data Exchange (ETDEWEB)

    Matsui, K.; Sugita, T.; Imamura, Y. [Kobe Steel, Ltd., Kobe (Japan)

    1997-09-01

    The advanced `KS-5` dry film type lubricant was developed for press forming of aluminum sheets. KS-5 uses water- soluble resin poly-alkylene-oxide superior in formability, weldability and adhesivity, and contains higher fatty-acid soap as oil solvent to improve a formability. The verification test result of KS-5 is as follows. Both stretchability and drawability were confirmed through a ball head stretching test and a cylinder drawing test as formability test, respectively, and a forming height more than that of mild steel sheets was obtained by using the solid lubricant showing a high stretchability. The drawability of nearly 80% of that of mild steel sheets was also obtained showing a high formability. Since the amount of the solid lubricant has reciprocal effect on the formability and degreasing property, it is important to select the suitable amount of the solid lubricant according to use conditions. Lubricants generally deteriorate a spot weldability, however, this lubricant has no practical problems by coating rust preventive oil. 3 refs., 8 figs., 3 tabs.

  2. Development of a high performance carbon fiber fabrics. Koseino tanso sen'i orimono no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, A.; Honma, K.; Matsui, J. (Toray Industries Inc., Tokyo (Japan). Composite Materials Research Lab.)

    1993-01-15

    On setting a position as an intermediate material for the advanced composite materials (ACM), carbon fiber fabrics is required to improve its optimization of the fiber orientation and structure of the fabrics under consideration on anisotropy of the composite materials in order to establish their higher performance. And, it also becomes important to establish energy conservation in higher order of processing containing their molding in order to make great strides the application range of the ACM. The ACM is generally a laminate comprising of some sheet-like, thin substrates arranged the reinforced fibers in one- or two-dimensional direction. As it has some high performance, mechanical properties because of the fiber orientation in a plane direction, its mechanical properties among the layers are determined by adhesion and its strength between the fibers and the resin and weak without any fiber reinforcement in its layer direction. As a method of its improvement, development of a fabrics or twisted yarns having the fibers oriented in three-dimensional direction is proceeding, but they have some limits in their fiber orientation yet and inferior productivity. A technical development of stitched preform is now executed as a low cost molding process. 9 refs., 7 figs.

  3. Development of high-performance sintered friction material for synchronizer ring; Koseino shoketsu synchronizer ring masatsu zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Miyajima, K; Fuwa, Y; Okajima, H; Yoshikawa, K [Toyota Motor Corp., Aichi (Japan); Nakamura, M [Japan Powder Metallurgy Co. Ltd., Tokyo (Japan)

    1997-10-01

    Increasing vehicle speed and power, high-performance synchronizer ring of manual transmission is required. We develop double layer sintered synchronizer ring for high performance and cost reduction. The main structure is consisted of ferrous sinter for high strength. In this paper, friction materials of sintered synchronizer ring are studied. We can get the good friction and anti-wear property by means of hard particles (FeTi, ZrO2), solid lubricant (Graphite) and suitable porosity in brass sinter matrix. And we also achieve high joining strength between double layers adding Cu-P material. 6 refs., 13 figs., 2 tabs.

  4. New energy introduction guidebook for Chugoku area; Shin energy donyu guidebook. Chugoku chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-05

    A guidebook was edited for the purpose of assisting introduction of new energies. Sections consist of Section 1, new energies available in the Chugoku area; Section 2, procedure for new energy introduction; Section 3, assistance institutions by energy; and Section 4, the status of new energy introduction in the Chugoku area, the future introduction targets, and referential materials. Section 1, upon defining the new energies, summarized features of photovoltaic power generation, solar heat utilization, wind power generation, wastes power generation, cogeneration, fuel cells, clean energy fueled automobiles, and introduction records up to the year 2000. Section 2 summarizes the general roles of local governments in the introduction, processing procedures for individual programs, related regulations, and summary of the assistance institutions. Section 3 puts into order the assistance institutions by energy. Section 4 summarizes precautions, targets and records in introduction by each new energy. The referential materials include a list of the Japanese assistance institutions, and subsidy institutions related to new energies for local governments in the Chugoku area. (NEDO)

  5. Guidebook for introduction of snow/ice cool energy; Seppyo reinetsu energy donyu guide book

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of contributing to the promotion of introduction of snow/ice cool energy in cold snowing areas, investigational study was made such as analysis of samples of introduction of snow/ice cool energy and effects. In the survey, for three kinds of the snow/ice cool energy system, that is, snow air-conditioning/refrigerating system, ice shelter system and artificial frozen soil system (heat pipe), each of the samples of introduction was outlined, and the effect of introduction by system was analyzed. As to the evaluation of economical efficiency, constructed were 12 kinds of the snow/ice cool energy spread type model system by the demand facilities including distribution facilities of perishable foods and shopping centers, hospitals and multiple dwelling houses, commercial/residential facilities such as office buildings, and industrial facilities such as food factories. These was comparatively studied with the electric air-conditioning system. As a result, it was made clear that the total cost was approximately a half times as high as that of the electric air-conditioning system, but the system had great incentive effect, supported by subsidies for the initial investment. (NEDO)

  6. Feasibility study on the introduction of hybrid buses; Hybrid bus donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose of this research is to design pilot projects for introducing hybrid buses into the public transportation sector. This research also covers contents regarding hybrid buses with a trolley-collector motor and a diesel engine, to identify technical and economical problems and to analyze cost beneficiation using hybrid buses. The trolley parallel hybrid system has been employed for the feasibility study. This system has abundant operation results in Europe and the USA. Its battery is small or is not necessary, and the maintenance cost is also low. As a result of the feasibility study, reduction effects of CO2 emission were found out. When the CO2 generation at the power plant is not counted, the reduction effect was estimated to be 32% compared with the CO2 emission from diesel buses. When the CO2 generation at the power plant is considered, it was estimated to be 18%. The cost beneficiation was investigated for the cases of the transportations using trolley system surrounding a medium-scale terminal among large-scale housing development, tourist resort, and stations. The annual income is estimated to be larger than the annual payment in each case. It was found that the hybrid bus is economically established. 17 refs., 48 figs., 41 tabs.

  7. Guidebook for introducing the photovoltaic power generation; Taiyoko hatsuden donyu guidebook

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-01

    Recently the number of installation of the photovoltaic power system has been increasing. At present, the estimated introduction amount is 70,000-80,000 kW, which is still big in difference with the targeted introduction value. As seen in the increase in the number of installation, the trend toward the introduction is increasing, but there are left problems on the introduction such as 'the cost is high,' 'the information on the installation has not been well known.' Also in future, it is necessary to further promote the installation, tackling factors to hinder the introduction and making efforts to prepare for the introduction environment. In consideration of such background, in this guidebook, the items required when local governmental organizations, business operators, etc. study the introduction of photovoltaic power system were arranged. Also arranged were the outline and introduction samples of photovoltaic power system, general information on the introduction of the subsidy system, etc., procedures of planning/design, how to concretely introduce the related rules, various procedures to be taken, etc. For reference, the guidebook includes drawings of samples, data on the test field projects which have been carried out so far, data on solar radiation, etc. It is expected that the guidebook will be a help to the understanding of the photovoltaic power generation and will connect to further promotion of the introduction. (NEDO)

  8. Wastes power generation introduction manual. Main edition; Haikibutsu hatsuden donyu manual. Honpen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A practical and specific working manual was prepared that satisfies the standards and criteria defined in the relevant law such as the Sanitation and Environment Ordinance No. 249, the guideline for generation of dioxins caused by refuse disposal, and that enables the reports evaluating the wastes quantitatively to be submitted to heads of the local governments when persons in charge of planning the introduction of wastes power generation at local governments discuss the wastes power generation systems. Taking general combustible wastes and sewage sludge treatments as the object, this paper details from the economic performance to size of wastes treatment at the priority limit for the power generation facility introduction. The subject power generation systems include the following: the stoker furnace/separation type ash melting furnace power generation system, the fluidized bed/separation type ash melting furnace power generation system, and the direct type gasification melting furnace power generation system, whose establishment of safety, reliability and stability have been verified by full-size system operation record available at the local governments, the gas turbine re-powering composite type power generation system (gas turbine power plants are installed beside the incineration furnaces) that makes high-efficiency power generation possible, and the RDF power generation system (power generation by mixed combustion with general refuses, and power generation using RDF (refuse derived fuel) exclusive combustion). Other important discussion and assessment items include environment and resource utilization performances. (NEDO)

  9. Guidebook for introducing the photovoltaic power generation; Taiyoko hatsuden donyu guidebook

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-01

    Recently the number of installation of the photovoltaic power system has been increasing. At present, the estimated introduction amount is 70,000-80,000 kW, which is still big in difference with the targeted introduction value. As seen in the increase in the number of installation, the trend toward the introduction is increasing, but there are left problems on the introduction such as 'the cost is high,' 'the information on the installation has not been well known.' Also in future, it is necessary to further promote the installation, tackling factors to hinder the introduction and making efforts to prepare for the introduction environment. In consideration of such background, in this guidebook, the items required when local governmental organizations, business operators, etc. study the introduction of photovoltaic power system were arranged. Also arranged were the outline and introduction samples of photovoltaic power system, general information on the introduction of the subsidy system, etc., procedures of planning/design, how to concretely introduce the related rules, various procedures to be taken, etc. For reference, the guidebook includes drawings of samples, data on the test field projects which have been carried out so far, data on solar radiation, etc. It is expected that the guidebook will be a help to the understanding of the photovoltaic power generation and will connect to further promotion of the introduction. (NEDO)

  10. New energy introduction vision in Chiba Prefecture; Chibaken shin energy donyu vision

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys and discussions were given on establishing a new energy introduction vision in Chiba Prefecture. The basic conception for new energy introduction regarded important the handling of global environment problems, improvement of the global environment, enhancement in energy security, and assurance of the regional performance of disaster prevention. New energy introduction is thought making it possible to create attractive urban spaces, make living environment more agreeable, and promote and breed new industries including the eco-business. Important measures may include the followings: introduction of new and economic energies in multiple ways for individual buildings and facilities, development of environment symbiotic cities utilizing new energies, improvement of region symbiotic cities in industrial zones, effective utilization of energies from wide-area refuses and wastes, establishment of an urban type cleaning plant that utilizes effectively energies from general wastes, new energy utilization in coordination with agricultural activities, utilization of new energies in fishery industry areas, and expansion in use of clean energy fueled automobiles including natural gas fueled automobiles. (NEDO)

  11. Wastes power generation introduction manual. Material edition; Haikibutsu hatsuden donyu manual. Shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    This paper collects and puts into order the materials used in preparing the manual. The materials were classified into the power generation system database related to discussion of the economic performance, case studies, technical materials, other referential materials and glossary. The database shows power generation efficiency, auxiliary power ratio, construction cost, utility cost and number of operators. The case studies present examples of economy calculations on the five recommended power generation systems at a wastes treatment capacity of 180 tons a day. Technical materials put into order the technological discussions on efficiency improvement, environmental measures (suppression of discharge of dioxins, measures for their removal, and the effects thereof), refuse derived fuel (RDF) and power plant operating techniques. The other referential materials collect laws, notifications, and guidelines related to the Welfare Ministry, laws, notifications, criteria and related to the Ministry of International Trade and Industry, and materials related to LCA, forms of power generation business entities, general wastes disposal business, and electric business bonds. The glossary explains terms required for operation and understanding of the manual. (NEDO)

  12. Effect of groupware introduction on office works; Groupware donyu no white color gyomu e ataeru eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Baba, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-05-01

    Investments for information systems in Japanese firms have been shifting from those for main frame systems to PC, LAN and groupware systems. Described herein are effects of groupware introduction on office works, and efficient introduction and practical application of these systems. The groupware functions are divided into information sharing, analyzing, integrating and coordinating functions, and changed information transmission as a result of practical application of each function has been followed by literature and questionnaire surveys on experiences at advanced enterprises. The results indicate that the changes are represented by 6 patterns, from replacement of information media to changes in working styles. The major productivity-related effects brought by introduction of these systems are decreased document volumes and improved skills of employees. The notable effects on office works are improved efficiency resulting from allotting one personal computer to each employee and from introduction of E-mail systems which solve problems involved in telephone communication. 15 refs., 11 figs., 10 tabs.

  13. Introduction guide book for wind power generation; Furyoku hatsuden donyu guide book

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper arranges essential items for introduction of wind power generation to local governments. Natural wind power energy which is free from emission of atmospheric pollutants such as CO2 and probably profitable, is leading regenerative energy among several new energies, and its rapid diffusion is expected. At the end of 1995, a wind power generation facility capacity amounts to 4900MW in the world, 1770MW in USA, 1140MW in Germany, 630MW in Denmark, 550MW in India, and 250MW in the Netherlands. In Japan, its introduction to local governments is in progress with preparation of a purchase system of surplus electric power and a system interconnection guideline. A total facility capacity reached 10MW in 1996, and is scheduled to reach 150MW in fiscal 2010. NEDO`s wind characteristic map of Japan shows many promising areas for power generation. Since these information is not yet well known, the following are summarized: the present state, features of wind condition, power generation systems, application cases, an approach to survey research, construction, maintenance and related laws, and a subsidy system. 31 refs., 48 figs., 40 tabs.

  14. Programs for promoting new energy introduction into Wakkanai City; Wakkanaishi shin energy donyu sokushin keikaku keikakusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The average temperature in the summer season at Wakkanai is 19 degrees C, and below zero degrees C in the winter season. Solar radiation duration is shorter in November through February due partly to the presence of snow. In terms of total solar radiation amount, the city occupies a middling position in the whole Hokkaido island. As for the force of the wind, a daily maximum wind velocity of 10m/s or stronger occur on 8 to 10 days every month in the period October through May. As projects for promoting new energy introduction, the below-named ones are chosen and subjected to examination for feasibility. They are a wind power generation system for a water purification plant; a district heating system utilizing cogeneration at the city middle sector; a hybrid system of methane fermentation and wind power generation for a public stock-rearing farm; a hybrid system of cogeneration and photovoltaic power generation for Fujimi district accommodation facilities; and photovoltaic power generation as a clean energy introduction system for a general gymnastic hall of Wakkanai City. Since the above-named subjects are all excellent in economy and environmentally-friendliness, it is suggested that efforts be exerted to realize them. (NEDO)

  15. FY1995 study of design methodology and environment of high-performance processor architectures; 1995 nendo koseino processor architecture sekkeiho to sekkei kankyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The aim of our project is to develop high-performance processor architectures for both general purpose and application-specific purpose. We also plan to develop basic softwares, such as compliers, and various design aid tools for those architectures. We are particularly interested in performance evaluation at architecture design phase, design optimization, automatic generation of compliers from processor designs, and architecture design methodologies combined with circuit layout. We have investigated both microprocessor architectures and design methodologies / environments for the processors. Our goal is to establish design technologies for high-performance, low-power, low-cost and highly-reliable systems in system-on-silicon era. We have proposed PPRAM architecture for high-performance system using DRAM and logic mixture technology, Softcore processor architecture for special purpose processors in embedded systems, and Power-Pro architecture for low power systems. We also developed design methodologies and design environments for the above architectures as well as a new method for design verification of microprocessors. (NEDO)

  16. Fabrication of low cost high performance large size composite structures by electron beam curing (EBC); Denshisen koka (EBC) ni yoru tei cost koseino ogata fukugozai kozo no seizo

    Energy Technology Data Exchange (ETDEWEB)

    Kamimura, K.; Parrot, P.

    1996-03-15

    This article introduces the electron beam curing (EBC), which is high speed non-heating cure technique for the high performance resin for structures, conducted by Aerospacial Co., Ltd. In this technique, very strong electron beam and X-ray are used in response to the thickness of curing region of members, and the muzzle has energy of 10 MeV as permeation control energy and power of 20 kW as cure time control power. Advantages of fabrication of composite products by EBC is derived from the elimination of exoergic and heating curing processes and the local cure molding. For the EBC, the residual stress is not generated, the size is stable, the insertion of different materials is easy without mismatch of thermal expansion between the composites and metals, the homogeneous bridge can be obtained to stabilize the material quality, the processing time can be shortened, it is suitable to mass production, and the cure of products can be controlled. About 30% to 40% of the cost of products can be reduced. 1 ref., 6 figs., 1 tab.

  17. Survey of a technology to introduce the waste-fueled power generation. Basic manual for introduction of the waste-fueled power generation; Haikibutsu hatsuden donyu gijutsu chosa. Haikibutsu hatsuden donyu kihon manual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Local government offices, etc., which are expected to shoulder responsibility for introducing the waste-fueled power generation, want to need exact information on technical information concerning the waste-fueled power generation and the method to materialize the introduction plan, etc. Therefore, Electric Power Development Co. surveyed and studied it under the contract with NEDO. The results were collected together as a basic manual for introduction of the waste-fueled power generation. As an outline of the waste-fueled power generation, the manual explains the significance, the present situation and potentials, the waste-fueled power system, an outline of working out the waste-fueled power generation plan, an outline of construction and operation/maintenance of the waste-fueled power generation, an outline of various systems relating to the waste-fueled power generation, etc. As the items for the study of making a concrete plan for power generation equipment, the manual explains the amount of refuse to be incinerated, the present status of generation capacity as viewed from the quality of refuse, the quality of refuse and the design of power generation equipment, boiler efficiency, power generation efficiency, construction cost and operation cost, etc. In addition, the paper describes a case study of the waste-fueled power generation plan. 118 figs., 39 tabs.

  18. Introduction effect of a load levelling system in an electric power system with a photovoltaic and wind system; Taiyoko/furyoku hatsuden wo donyu shita denryoku keito ni okeru fuka heijunka shisutemu no donyu koka

    Energy Technology Data Exchange (ETDEWEB)

    Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)

    1998-12-05

    Introduction effect of load levelling system by a battery in an electric power system by a battery in an electric power system with a PV and wind system is investigated. Charge and discharge power of the battery are determined from a load curve and every hour data of PV and wind output. Annual cost of the power system is calculated from the generating power and the capacity of each source via the installed utility capacity and the capacity factor. It is found that (1) the battery system reduces the maximum demand and improves the load factor, (2) the cost effect of the battery system when introducing the PV system is higher than that when introducing the wind system. (author)

  19. Fiscal 1999 edition. Guidebook for introducing new energies in Kinki District; Kinki chiiki shin energy donyu guide book

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    The captioned guidebook is composed of the following subjects: (1) the current status and problems of new energies (the energy status and the current status of new energies in Japan, and approaches to new energies in Japan); (2) the status of introduction and works in Kinki District (the outline of introduction and works in Kinki District on photovoltaic electric power generation, solar heat utilization, wind power generation, wastes power generation, clean energy fueled automobiles, cogeneration, fuel cells, unused energies, and other reproducible energies); (3) NEDO related supportive institutions (new energy introduction promotion projects by NEDO, and the outline of different supportive institutions); (4) new energy introduction flow (total flow leading to the introduction, and introduction flow by new energies); (5) the grand new energy prize in Kinki District (what is the grand new energy prize? and cases of prizes awarded in Kinki District); (6) new energy related supportive institutions (a list of the related institutions, and the outline of different supportive institutions); and (7) new energy consultation windows and contacts (consultation windows and contacts for general new energy aspects and the government related supportive institutions, and consultation windows by new energies). The grand new energy prize is awarded by New Energy Foundation as the 'institution for public recognition of new energy devices of the 21st century type'. (NEDO)

  20. 17th Symposium of NEDO projects. Introducing/spreading project subcommittee; Donyu fukyu jigyo bunkakai. Dai 17kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    The results of the following themes are presented in this subcommittee; (1) outline of the new energy introduction promotion department, (2) the project results, and (3) introduction of the examples. For the theme (1), NEDO is supporting the projects for introducing and promoting new energy systems, feasibility studies for introduction of these systems, and field test (FT) projects to accumulate the experiences, e.g., collecting the data by operating these systems under actual loads, development and technology demonstration projects for introduction of new energy systems, and advisory projects for supporting introduction of new energy systems. For the theme (2), those results reported include the results and examples of the FT projects for power generation by photovoltaic cells and wind power generation, results of the FT project for power generation by fuel cells and creation of the FT projects for pioneer high-efficiency energy systems, current status of the environment-friendly energy community projects (heat supply systems), results and examples of the environment- friendly energy community projects (power generation projects), demonstration tests for establishing the distributed power supply systems of the next generation, tests for establishing techniques for, e.g., load-leveling in power generation by photovoltaic cells for residential purposes, results of the project for technology of utilizing unutilized energy, survey on the techniques for power generation by wastes, and advisory projects for supporting introduction of new energy. (NEDO)

  1. Fiscal 1999 edition. Guidebook for introducing new energies in Kinki District; Kinki chiiki shin energy donyu guide book

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    The captioned guidebook is composed of the following subjects: (1) the current status and problems of new energies (the energy status and the current status of new energies in Japan, and approaches to new energies in Japan); (2) the status of introduction and works in Kinki District (the outline of introduction and works in Kinki District on photovoltaic electric power generation, solar heat utilization, wind power generation, wastes power generation, clean energy fueled automobiles, cogeneration, fuel cells, unused energies, and other reproducible energies); (3) NEDO related supportive institutions (new energy introduction promotion projects by NEDO, and the outline of different supportive institutions); (4) new energy introduction flow (total flow leading to the introduction, and introduction flow by new energies); (5) the grand new energy prize in Kinki District (what is the grand new energy prize? and cases of prizes awarded in Kinki District); (6) new energy related supportive institutions (a list of the related institutions, and the outline of different supportive institutions); and (7) new energy consultation windows and contacts (consultation windows and contacts for general new energy aspects and the government related supportive institutions, and consultation windows by new energies). The grand new energy prize is awarded by New Energy Foundation as the 'institution for public recognition of new energy devices of the 21st century type'. (NEDO)

  2. Report for fiscal 1998 on feasibility study for introduction of electric automobiles; 1998 nendo denki jidosha donyu kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys have been made on the characteristics of environmentally harmonizing automobiles, and the status of development and introduction thereof inside and outside the country. Discussions were given on the possibility of introducing electric automobiles in Japan. In developing environmentally harmonizing automobiles in Japan, works have been executed on low pollution type components such as lean burn engines, electric automobiles, gasoline engine and electric motor hybrid cars, methanol fueled cars, and fuel cell automobiles. Some of them are already in use in spite of their high price. In America, a cooperation project for the next generation cars has been implemented by mobilizing industrial, academic and governmental organizations. Based on the achievements thereof, the car makers have announced their original advanced cars respectively. In the EU, development of low exhaust gas cars and zero emission cars is being carried out jointly by the related industries setting years 2003 to 2005 as the target. An urban type traffic system utilizing electric vehicles, and a traffic system dividing movements of short distance and long distance are proposed as the means to introduce the future electric automobiles. (NEDO)

  3. Data book of new energy introduction to Hokkaido. FY 2000 version; Hokkaido shin energy donyu data shu. 2000 nendoban

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of effectively introducing/promoting new energy and of supplying the basic data which contribute to the promotion/education, the actual results of new energy introduction to Hokkaido were collected/arranged. New energies to be surveyed were the photovoltaic power generation, solar heat utilization, wind power generation, waste power generation, waste heat utilization, waste fuel production, biomass energy, unused energy, gas generation, petroleum cogeneration, fuel cells, clean energy vehicles, small-/medium-scale hydroelectric power generation, etc. The purpose of the book is mainly to collect the basic information, that is, what kind of new energy has been introduced to what kind of area. The data are so collected that facilities adopting new energy can be seen as unit of city/town/village as a rule. The method to collect information is based on the total collection of the reports made by organizations in/outside Hokkaido. The book additionally covers the details of the data supplied and the data collected. (NEDO)

  4. Investigation into introduction and promotion of clean energy cars; Clean energy jidosha no donyu sokushin ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Gazing the introduction target for fiscal 2000 and 2010, the paper arranged comprehensively and systematically the trend in Japan and overseas of clean energy cars and described subjects. Themes of the study to be promoted in terms of electric cars are: Li secondary batteries, heightening of performance of batteries such as Ni-hydrogen, power generation/power storage hybridization to make the long-distance travel possible. For the price reduction, the body is so made as to make it possible to select three kinds of power unit, that is, gasoline, hybrid, and electricity. Low noise and easy operation are also important. As to natural gas vehicles, the price is more than three times as high as that of gasoline vehicles, and relaxation of the related regulations on metal tanks, the Road Traffic Act, etc. is necessary. It is indispensable to establish quantity production and technical standards and reduce cost by the remodeling for bi-fueling with gasoline engines, development of FRP tanks, etc. Methanol vehicles are the closest to gasoline vehicles, but the introduction is delayed having no groups for generalization. Solar and hydrogen cars are promising, but are on a stage of developing the basic technology. 43 figs., 104 tabs.

  5. Effects of peak shaving technologies in the residential and commercial sector; Minsei bumon no fuka heijunka gijutsu no donyu koka

    Energy Technology Data Exchange (ETDEWEB)

    Nagata, Y. [Kyoto University, Kyoto (Japan); Takahashi, M.; Uchiyama, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-09-01

    This paper analyzes how much of the power demand could be reduced in the future by improving efficiencies of electric power utilizing appliances used in the residential and commercial sector. It discusses whether the reduction would lead to load leveling. Annual load rate in the power demand is continuing to decrease because of power demand increase in the residential and commercial sector, and increase in demand for air conditioning in summer. If a technology to improve electric appliance efficiency is proliferated to its maximum scope, the annual load rate in fiscal 2014 may be improved by 1.1 percent point. Since the improvement allows new power generation facility installation cost to be deferred, the power generation unit cost can be reduced by 0.11 yen per kwh. If a heat storage type air conditioning technology is proliferated to its maximum scope, the annual load rate in fiscal 2014 can be improved by 1.8 percent point, and the power generation cost may also be reduced. If the device efficiency improving technology and the heat storage type air conditioning technology are introduced to their maximum simultaneously, the annual load rate in fiscal 2014 can be improved by 2.5 percent point, and the power generation cost may also be reduced by 0.24 yen per kwh. If a promotion policy is taken on proliferation of a specific device efficiency improving technology having excellent economic performance by providing subsidy, the reduction amount of cumulative power generation expense will be much greater than the required subsidy amount. 10 refs., 9 figs., 22 tabs.

  6. Investigations on installation of the heat exchange system in geothermal wells; Chinetsu koseinai netsukokan system donyu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The heat exchange system in geothermal wells is a system that replaces the air source heat pump and uses underground beds or groundwater as a heat source to heat rooms by collecting underground heat in winter, and cool rooms in summer by operating a heat media circuit in reverse direction through the action of a reverse flow valve to discharge heat underground. This paper describes feasibility investigations on the system including its technical trend for introducing the system technology. Technological and economic discussions were given by classifying the intra-well heat exchange device in its installation direction (horizontal loop type and vertical installation type), underground heat exchange media (antifreeze solution/water cyclic system and direct expansion system), and underground heat transfer (heat conduction system and heat convection system). As a result of discussing each system, it was concluded that the following two systems are promising: A = vertical installation, antifreeze solution/water cyclic and heat conduction system, and B = vertical installation, antifreeze solution/water cyclic and heat convection system. Since the system B was found to have better efficiency and economy among both systems, it is necessary to verify an intra-well heat exchange system and operation methods that suit the system B effectively. 21 refs., 8 tabs.

  7. Feasibility study on introducing new energy systems into Asian villages; Asia sonraku ni okeru shin energy donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For improvement of living standards in unelectrified areas of Asia, the feasibility of new energy power generation systems was surveyed. The degree of electrification of local areas is different every country, and Thailand is ahead of other countries, while Laos and Cambodia are most unelectrified. Power supply of 100W/house seems to be adequate for local areas because of weather condition, housing situation and life-style. Economic support and education on electricity are necessary for poor areas. Although needs for new energy is increasing, the priority is given to industrial and urbanized areas because of cost and investment effects, and remote areas are dependent on grant- in-aid. Resources of photovoltaic, wind power and micro- hydraulic energies are abundant, however, selection of energy and verification of its usability are important, and the local energy density maps were thus prepared. In introduction of new energy, after selection of energy suitable for an area concerned, such geographical and social conditions should be surveyed as road condition, water rights, land utilization, economic support system, policy and intention of inhabitants. 76 refs., 68 figs., 91 tabs.

  8. Making of composite type energy introduction models in cities; Toshi ni okeru fukugogata energy donyu model no sakusei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper made and studied simulation models in case of introducing new energy of composite type to cities. In the study, using a standard composition unit of city as a cluster, the compositional element was divided into 25 cells, which were divided into the residence superiority cell and the business superiority cell. The residence superiority cell was divided into highrise and lowrise. The calculation program is to simulate effects of introducing new energy such as the photovoltaic power generation, solar energy utilization, waste power generation, cogeneration, and unused energy like river water and waste water. Using the program, the analysis of sensitivity was conducted concerning how the outputs will change according to differences in energy consuming composition in the urban area. The calculation was conducted concerning local cities of the warm area, local cities of the cold area, local cities of the subtropical area, residence/working-place neighboring core cities in the warm area, central areas of large cities of the warm area, and new towns of the warm area. 28 figs., 27 tabs.

  9. FY 1999 data book for the introduction of new energy to Hokkaido; 1999 nendoban Hokkaido shin energy donyu data shu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of effectively promoting the introduction of new energy to Hokkaido, it is necessary to comprehensively/systematically arrange various kinds of new energy and to furnish the basic data which contribute to the spread/education. The paper collected/arranged the actual results of the introduction of new energy to Hokkaido, using the existing data, etc. Attention is paid to the collection of the basic information on what kinds of new energy have been introduced in what kinds of regions, etc. Fundamentally, the data were collected by which facilities for new energy can be seen by city/town/village. The new energy for collection is basically within the range of those included in the New Energy Law. They are renewable energy (photovoltaic power generation, solar heat utilization, and wind power generation); recycle type energy (waste power generation, waste heat utilization, fuel production, waste fuel production, biomass energy, and unused energy); new forms of the existing energy (gas/oil cogeneration, fuel cell, and clean energy vehicle). (NEDO)

  10. Basic research report on introduction of new energy into Yamaguchi Prefecture; Yamaguchiken shin energy donyu kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In Estimation Work 1, the potentially available amount (the amount in existence) is determined for each type of new energy by use of various new energy related technologies now available. In Estimation Work 2, the available amount is determined for each type of new energy, with social restraint and installation space taken into consideration. Effects upon energy saving and CO2 emission reduction are 4405.2% and 3439.1% in Estimation Work 1, and 6.5% and 8.0% in Estimation Work 2. A conclusion is reached after examining the outcomes of the said estimation works and the results of simulations (conducted on the assumption of new energy introduction in fiscal 2010), the number of advocates expressing their support of new energy adoption in questionnaires answered by various businesses and offices in the prefecture, high possibilities of introduction detected in a survey of exploitation projects of cities, towns, associations, and unions, and the prospect of acceptance by households. The conclusion is that the types of new energy and technologies to be selectively introduced into the prefecture will be photovoltaic power generation, wind power generation, clean energy vehicles, energy extracted from wastes, cogeneration, fuel cells, passive solar system, utilization of waste heat from factories and mills, and ocean energy. These are abundant in terms of potentially available amount and of available amount. (NEDO)

  11. Plan to promote new energy introduction in Niigata Prefecture area; Niigataken chiiki shin energy donyu suishin keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The 'Plan to promote new energy introduction in Niigata Prefecture area' was established to leave the conditions that everybody can live with affluence and comfort in the next generation. The plan lasts for ten years until 2010. Upon identifying the district characteristics of Niigata Prefecture, and based on the results of investigations on new energy existence quantity, utilization possibility thereof, and consciousness of residents of the prefecture, considerations were given that the plan shows the basic policy to promote proliferation of the new energies, and serves as the guideline for practical implementation. The plan document is composed of the following four items: 1) the foreword, 2) the current status of energies, 3) new energies expected of introduction, and 4) basic measures. The energy consumption was estimated to increase to 1.345 times that of fiscal 1990 in the year 2010, the increase being mainly in consumer and household use. The targeted quantity for new energy introduction was set to 90,000 kl annually as converted to petroleum. Expected new energy applications would include photovoltaic power generation, snow energy and solar heat utilization, and cogeneration utilizing natural gas. (NEDO)

  12. Fiscal 1997 report on the survey of the actual state of various coal related industrial furnaces in China; 1997 nendo chosa hokokusho (Chugoku ni okeru sekitan ni kakawaru kakushu kogyoro no jittai chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is thought that environmental prevention technologies related to boilers which are the largest coal use field in China have been almost all made model projects till now. Further, coal or coke is used in various industrial furnaces except boilers in every industrial sector in China. The amount of coal use there is large next to that in boilers, which is a cause of the country`s serious air pollution. Accordingly, an investigation was commenced in fiscal 1997 aiming at grasping the actual state of environmental pollution caused by various coal related industrial furnaces in China and studying the environmental improvement. This time, various industrial furnaces were examined in chemical and iron/steel industries. It could be inferred that both industries made efforts to enhance and rationalize production activities and then give consideration also to the environmental prevention. Generally, however, most plants still have old-fashioned production facilities, while the facilities are being modernized little by little. It was found that in China productivity was lower than Japan and the environmental pollution was in a serious condition. 16 refs., 28 figs., 69 tabs.

  13. Empirical analysis of consumer decision making processes on setting up residential photovoltaic systems; Jutakuyo taiyoko hatsuden system no donyu ni kansuru ishiki bunseki

    Energy Technology Data Exchange (ETDEWEB)

    Iuchi, M; Okawara, T; Tsuchiya, T [Central Research Institute of Electric Power Industry, Tokyo (Japan); Konakayama, A [Tokai Univ., Tokyo (Japan)

    1996-10-01

    Inquiries are made to consumers (monitors) who own a photovoltaic power generation system at their houses, and their replies are analyzed for isolating the factors involving the purchase of this domestic power generating system. A large part of the monitors are 40-50 years old males in the relatively high income bracket. They are very interested in problems of global environments, resources, and energy, and are inclined to assume value-consciousness and life-style which encourage them to love health and nature, participation in social functions, and decision-making. The need for the protection of global environments occupies more than 90% of the reasons for their adoption of photovoltaic power generation. The monitors strongly feel, however, that they paid very much for the apparatus although they were granted some subsidies. As for motives for their acquisition of the system, their answers are categorized into four groups according to their responses as to whether (or not) they expect economic merits though dependent on future development and whether (or not) they accept the current energy policies. The result shows that some monitors think like average citizens. 17 refs., 22 figs., 11 tabs.

  14. Survey of the waste-fueled power generation introducing technology. Case study 1 (fiscal 1996); Haikibutsu hatsuden donyu gijutsu chosa nado. Case study no jisshi 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A case study on A city was conducted aiming at making a detailed manual for introducing the waste-fueled power generation. The study was made in terms of a large-capacity waste-fueled power plant, estimation of the waste amount considering wide-area processing, size of facilities, comparison of four types of combustion furnace, steam condition/seawater cooling/power generating efficiency, etc. As a result, the following were proposed: As to the size of facilities, a capacity as large as possible is recommended in the light of the scale merit of costs of the waste-fueled power plant and final disposal site and the environmental preservation. Concerning the high efficient power generation, recommended are 450degC and 60-80 ata which are steam conditions for coping with high temperature corrosion. In respect to seawater cooling, the adoption is recommended making good use of locational conditions since the output energy increases by approximately 16%. Any furnace types including the fluidized bed furnace are equal. The amount of dioxin becomes below 0.1ng/Nm{sup 3} because of the control of furnace combustion temperature, residence time, catalytic desulfurization facilities, blowing of activated coal into the flue, etc. 172 figs., 78 tabs.

  15. Study of installation of PV systems at campus; Campus ni okeru taiyoko hatsuden donyu ni kansuru kenkyu (taiyo denchi nomi wo secchishita baai no yobi kento)

    Energy Technology Data Exchange (ETDEWEB)

    Tsuboi, N.; Tanaka, H.; Okumiya, M. [Nagoya University, Nagoya (Japan)

    1997-11-25

    In terms of energy consumption, environmentality and economical efficiency in the case of installing the photovoltaic power system on the rooftop of the university campus, a comparative study was conducted with other power generation systems. As objects to be comparatively studied, selected were the all-electric type centralized space heating/cooling system, cogeneration system, nighttime heat storage system and centralized system with solar cells installed. The panel area of the PV system is 10,000m{sup 2} on the rooftop and 7,000{sup 2} on the outer wall. About data on solar radiation, average values obtained in Nagoya were used. Assessment was made in terms of energy consumption amount at the time of operation, system COP, emission amounts of CO2, NOx and SOx at the time of manufacturing and operation, initial cost, running cost, etc. As a result of the study, an effect of reducing global warming gas was admitted in the PV system. However, the initial cost of the solar cell panel was high, and the life cycle cost of the PV system was lower than other systems. 1 ref., 7 figs., 3 tabs.

  16. Economical effect of introducing a photovoltaic system on future electric power system; Shorai no denryoku keito eno taiyoko hatsuden system donyu ni yoru keizaiteki eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Akata, N.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan)

    1997-11-25

    Economic impact of introduction in the future of photovoltaic power generation (PV) systems into the commercial power system is discussed from the electric utilities` point of view. In the discussion, future demand for power is predicted from the demand for power in the base year, and the optimum power source configuration corresponding to the future demand and power generation curve are worked out by use of linear programming. Then, the fixed cost and variable cost are calculated for each of the power source components, and then the expected reduction in cost per unit of power generated is calculated. As the power sources, the hydroelectric, pumped storage, oil-fired, coal-fired, LNG-fired, combined cycle, and atomic technologies are considered. The conclusion is stated below. Upon introduction of PV power equivalent to 10% of the maximum demand power, the maximum power in the service area of Chubu Electric Power Co., Inc., will be reduced by 1.23GW in 2025, and the yearly demand power by 5472GWh. Since PV lowers the peak, an increased number of power sources low in variable cost will be used although such will be low in tracking capability. An increase in power demand will enhance the cost reducing effect of the PV system. 5 refs., 4 figs., 3 tabs.

  17. On-line temperature control of fluidized bed incinerator using fuzzy algorithm; Fuzzu seigyo donyu ni yoru ryudosogata shokyakuro unten no jidoka

    Energy Technology Data Exchange (ETDEWEB)

    Okayasu, S.; Kuratani, T.; Imai, H. [Ajinomoto Co. Inc., Tokyo (Japan)

    1995-03-15

    Automatic control of incinerators for their stable operation has been desired for the preservation of the environment in the factory. An on-line fuzzy control system has been successfully introduced for temperature control of the fluidized bed of incinerator for industrial wastes. In this case, manual control can be applied to the plant instead of a PID control system, because of the complexity of the waste materials and the large delay in detection of the temperature change in the fluidized bed sand. On the basis of analyzing the dynamic performance of the process and the know-how of skilled operators, membership functions and fuzzy control rules are selected, then determined carefully for the system. Introduction of the system resulted in almost the same performance as manual control. Subsequently the operators are freed from manual operation in the control room for an hour. 6 refs., 5 figs., 4 tabs.

  18. Fiscal 1999 research report. Revision of introduction guidebook for wind power generation; 1999 nendo furyoku hatsuden donyu guide book no kaitei gyomu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Expectations are rapidly growing higher in Japan, whose energy supply structure is but fragile, that new energies upon introduction and diffusion will help settle emerging environmental problems such as global warming. For the acceleration of new energy introduction, it is necessary to supply autonomous entities etc. planning to adopt new energies with various materials such as basic knowledge of new energies, cases of successful introduction, and procedures to follow for their adoption. Wind power generation has come to attract attention as a environmentally-friendly clean method of energy supply, and there is a strong tendency towards its adoption. Under such circumstances, a guidebook has been prepared, in which study results are systematically written as to the items to consider before local autonomies etc. install their wind power generation systems. The main items in the guidebook are the outlines of wind power generation, wind characteristics, wind power generation system, precedents of wind power generation, how to conduct studies about wind power generation, construction and maintenance of wind power generation systems, procedures, laws, and regulations relating to wind power generation, and government subsidies for wind power development. (NEDO)

  19. Surveys in Hokkaido on promotion of structuring models to be introduced to convert wastes into energy; Hokkaido ni okeru haikibutsu energy ka donyu model kochiku sokushin chosa

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    With an objective of converting dairy farming wastes and fisheries wastes into resources to be used as energies, this paper discusses development trends and utilization possibilities thereof based on their utilization characteristics. The Tokachi, Abashiri and Nemuro regions produce more cattle wastes, and regions on the coast of the Sea of Okhotsk produce more hepatopancreas of scallop than other regions. The amount of energy from such wastes is subject to large seasonal variations. Methane gas production through methane fermentation is an effective treatment technology, although it is utilized less effectively in Hokkaido. Important is applying the processes depending on energy demand, supply characteristics and regional features. Taking waste utilization characteristics and regionally uneven distribution of resources into account, conceptions on six model systems that could be introduced were structured. The six systems include two types for fisheries wastes utilization, three types for agricultural and dairy farming wastes, and one type for combined utilization of agricultural and fishery wastes. Important factors to select suitable commercial operation sites and promote the operations are stable quantity assurance of waste resources, energy demand, and stable operation, such as could be available in fishery processing complexes and large dairy farming areas. 44 refs., 66 figs., 29 tabs.

  20. Fiscal 1999 survey report on introducing technique for predicting impact on hot spring; 1999 nendo onsen eikyo yosoku shuho donyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-10-01

    For the application of fruits of the geothermal development promotion project to survey phase C and for the study of technical means for appropriate development to employ after phase C, some cases of impacts imposed on hot springs by geothermal development were taken up and the causes of the impacts were investigated. Activities were conducted in the three fields of (1) the survey of actualities of impacts imposed on hot springs, (2) the survey of the causes of such impacts, and (3) a comprehensive survey. Keyword searches were conducted into the data system and geothermal energy related magazines, and 13 cases were found in which hot springs were affected by geothermal development, which included the Palinpinon district (Philippines), the Koso district (America), and the Wairakei district (New Zealand). Concerning the 13 cases, data on geology, geological structures, and geothermal fluids were collected and studies were conducted about relations of geothermal development with geological structures and geothermal fluids, as in the case of hot springs, and the two were integrated for the clarification of the causes of impacts. In concluding the report, the difference in mechanism is deliberated between cases with impacts on hot springs and cases without impacts on hot springs. (NEDO)

  1. Evaluation report on the R and D of the membrane separation process introduction technology; Makubunri process donyu gijutsu no kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper reported the R and D of the membrane separation process introduction technology during a period of 1994 through 1998. The membrane separation technology is not associated with the phase change which requires large energy and expected to be an energy saving process. For the production of membranes required of high functions, the vapor deposition polymerization method was considered, and high order structure control of the membrane, control of adhesion and attachment, and control of orientation, and development of the high polymerization technology were required. For the high grade control of vapor polymerization, the substrate surface structure/quality were important. The molecular level analysis of the vapor deposition surface was also needed. Therefore, the paper took notice of STM (scanning tunneling microscopy), AFM (atomic force microscopy) and HREELS (high resolution electron energy loss spectroscopy) as surface atomic/molecular configuration analysis technology, and designed/fabricated and studied the high resolving power and high sensitivity analysis equipment using the analysis equipment which combined HREELS and STM and the analysis equipment using SFG (sum frequency generation) which can detect signals in the low frequency region. Making full use of the highest technology, technology was able to be developed for substrate surface analysis and surface reaction analysis technologies which become the basis of the high performance separation membrane fabrication technology by the vapor deposition polymerization method indispensable for introduction of the membrane separation process. The technology can be the base applicable to a lot of fields where surfaces and interfaces are concerned

  2. Technical surveys on MHD combustors. Surveys on incorporation of pressurized coal partial combustion furnaces; MHD combustor gijutsu chosa. Kaatsugata sekitan bubun nenshoro no donyu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    The pressurized coal partial combustion (PCPC) furnace is surveyed/studied for its incorporation in MHD generation. The technical development of the atmospheric CPC has been basically completed, and the concept is demonstrated using a test system of commercial size. Many techniques developed for the atmospheric CPC are applicable to the PCPC system. These include structures of the CPC furnace walls, and slag handling and simulation techniques. Combination of PFBC with PCPC or IGCC can bring about many merits, e.g., enhanced efficiency and abated NOx emissions for the combined cycle power generation. These topping cycles, therefore, should be developed in the early stage. MHD power generation is one of the concepts that can enhance efficiency. In particular, the techniques for closed cycle MHD generation have notably advanced recently. The PCPC techniques are useful for coal combustors for MHD generation. Full-scale development works for the direct coal combustion gas turbine systems have been just started for the IGCC systems of the next generation, and the PCPC-related techniques are expected to serve as the central techniques for these turbine systems. (NEDO)

  3. Report for fiscal 2000 investigations on effects imposed by introducing emission trading system; 2000 nendo haishutsuryo torihiki system donyu ni yoru eikyo ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With regard to effectiveness of the emission trading targeted to reduce the greenhouse effect gas emission, evaluation has been given from the three viewpoints: economies, environment, and household economy. In the research, simulations were implemented by using the GEC calculation model modified for introduction of domestic emission trading, and utilization of international emission trading. In evaluating the effects on industries and foreign trades, notice was given on the large energy consuming industries to discuss the effects of introducing the emission trading on the quantity of production and export. Regarding the effects on environment, calculations and discussions were given on greenhouse effect gas leakage rates to assess the greenhouse effect gas emission reducing effects from the domestic and international viewpoints. As a result of the discussions, it was found that the economies, environment and household economy are all benefited in regard with the domestic emission trading. Utilization of the international emission trading was also found to have sufficient positive benefit exist for the economies and household economy. (NEDO)

  4. New energy vision for Oita Prefecture. Toward the adoption of eco-energy; 2001 nendo Oita ken shin energy vision. Eco energy no donyu ni mukete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For contributing to the preservation of the global environment, studies were made to work out a new energy introduction vision fully exploiting the characteristic features of Oita Prefecture. Oita Prefecture's demand for energy in 1998 is estimated to be 408.6 times 10{sup 15} J, with coal-based energy covering 204,016 TJ, oil-based energy 160,192 TJ, electric power 37,721 TJ, and so forth. The consumption will result in the emission of 35.77 million tons of carbon dioxide. According to Oita Prefecture's prospect of its eco-energy adoption in 2010, there will be 319 MW from hydroelectric power, 155 MW from geothermal power, 52 MW from photovoltaic power, 46 MW from clean energy vehicles, 33 MW from refuse-fueled power, and so forth. To prepare plans for facilities to utilize eco-energy and for regional development in the future through the use of such facilities, introduction costs were predicted and effects were simulated for model businesses engaged in biomass power generation using livestock wastes, small-scale hydroelectric power generation, bio-diesel fuel production, wind power generation, and woody biomass power generation. (NEDO)

  5. Fiscal 1998 research report. Feasibility survey on offshore wind power generation in Japan; 1998 nendo chosa hokokusho. Nippon ni okeru yojo furyoku hatsuden no donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey studied the feasibility of large-scale offshore wind power generation in Japan. Attempt was also made on preparation of outline maps of offshore wind around Japan. The cost of future offshore wind power generation systems is roughly dependent on technical issues and environmental issues. As technical issues, 'installation site,' 'foundation,' 'system interconnection' and 'maintenance/management' were summarized based on applications in Europe. As a result, it was clarified that technical issues can be solved with existing technologies to a certain extent, however, those relate to economical problems closely. The previous environment impact assessments say that wind power generation has no problems on the environmental issues. As relatively strong wind coastal areas, the outline maps of offshore wind point out Western Hokkaido area, Japan Sea area of Tohoku district, Pacific ocean area of the central part of Honshu, Genkai Nada area, Western Kyushu area and Southwest islands area, and suggest that these areas are promising for offshore wind power generation. (NEDO)

  6. Investigation on the development and introduction of new geothermal exploration technology. Part 2; Chinetsu shintansa gijutsu kaihatsu donyu ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    For the purpose of maintaining and increasing the geothermal power generation amount, the development was made of exploration technologies which become necessary in the stage of geothermal reservoir exploration and in the stage of reservoir management and peripheral development. As development technologies, the following were proposed: fracture flow characteristics exploration method (FE), production/circumference areas flow characteristics exploration method (PE), and integrated analyzing method (IA). As to FE, for the survey of geothermal fluid dynamic characteristics in fracture aggregate composing the geothermal reservoir, developments were made of the well hydraulic testing method for examining hydraulic characteristics of fracture system and of the fracture evaluation method composed of the core/logging analysis method, the permeability logging method and electroseismic exploration method. As to PE, for maintaining and managing steam production in the developmental area and developing the area to the circumference area, development was conducted of technology for exploring variations of reservoirs and fluid flow from the data on precision gravity, three-dimensional resistivity, fluid geochemistry, active seismic wave and self potential, precision electromagnetism, passive seismic wave, etc. As to IA, development was made of reservoir simulation technique, etc. 2 refs., 70 figs., 41 tabs.

  7. FY 1990 achievement report on the survey of possibility of introducing solar energy into buildings; 1990 nendo taiyo energy no kenchikubutsu eno donyu kanosei chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    This paper describes the achievements in fiscal 1990 on survey on possibility of introducing solar energy into buildings. Capacity of photovoltaic power generation facilities installed on an area of 1600 km{sup 2}, such as roofs of residential houses, schools and building may be calculated on a trial bases as 100 million kW at maximum. The capacity can replace 16% of the total demand and corresponds to 26.30 million kiloliters (9%) as converted to crude oil. If photovoltaic power generation is utilized on buildings of users, diversified technological criteria are required from the viewpoint of legislation covering wide range of architectural, electrical and disaster aspects. However, no direct and clear standards are available now, except for the electric power business law. What are urgently required are solar cell standardization, incentive subsidies, aging safety, institutions for electric power sale and purchase, and establishment of technological criteria. An utilization example survey revealed problems in array installation and size. Increased demand, mass production and cost reduction will create a favorable cycle. Introduction, proliferation, and acceleration under policies at public facilities which are expected of enlightenment and development into other areas will be the effective means for the purpose. (NEDO)

  8. Fiscal 1998 research report. Feasibility survey on offshore wind power generation in Japan; 1998 nendo chosa hokokusho. Nippon ni okeru yojo furyoku hatsuden no donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey studied the feasibility of large-scale offshore wind power generation in Japan. Attempt was also made on preparation of outline maps of offshore wind around Japan. The cost of future offshore wind power generation systems is roughly dependent on technical issues and environmental issues. As technical issues, 'installation site,' 'foundation,' 'system interconnection' and 'maintenance/management' were summarized based on applications in Europe. As a result, it was clarified that technical issues can be solved with existing technologies to a certain extent, however, those relate to economical problems closely. The previous environment impact assessments say that wind power generation has no problems on the environmental issues. As relatively strong wind coastal areas, the outline maps of offshore wind point out Western Hokkaido area, Japan Sea area of Tohoku district, Pacific ocean area of the central part of Honshu, Genkai Nada area, Western Kyushu area and Southwest islands area, and suggest that these areas are promising for offshore wind power generation. (NEDO)

  9. Achievement report for fiscal 1999. Research and development of high-performance magnetic materials creation technology making use of microgravitational environment; 1999 nendo bisho juryoku kankyo wo riyoshita koseino jisei zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are made to develop the above-named technology so as to improve on performance of magnetic materials for magnets extensively used in electric motors to consequently influence their energy conversion efficiency. For this purpose, probes are conducted into novel alloy phases, intermetallic compounds, and microstructure in a containerless coagulation process in which a molten body of a magnetic metal material in free-fall is allowed to cool rapidly, and a system is developed to enable a series of processes of heating and melting in preparation for containerless coagulation, specimen formation, and then coagulation in a microgravitational environment. The system is used for the study of novel materials for magnetic alloys and process technology. For the utilization of containerless coagulation in a microgravitational environment, it is necessary to make full use of the JAMIC (Japan Microgravity Center) facilities, and an experimenting apparatuses are fabricated for a containerless coagulation process and unidirectional coagulation process applicable to a free-fall test. In this fiscal year, some significance involving for example structural uniformity are found among the specimens created using containerless coagulation in a microgravitational environment, and it is inferred that the data as an index of higher performance will lead to studies in the next fiscal year and afterward. (NEDO)

  10. FY 1998 annual summary report on comprehensive development study of high-function flat panel display techniques (second year); 1998 nendo koseino flat panel display gijutsu no sogo kaihatsu kenkyu seika hokokusho. Daininendo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project is aimed at creation of the new world display industry in Shikoku by developing the high-function flat panel display techniques and thereby establishing new techniques which solve the problems involved in, e.g., LEDs, plasma-aided devices and ELs other than liquid crystal devices. For development of emitters using diamond, important results have been obtained for the morphology, and cathode luminescence, Raman and photoluminescence spectra of polycrystalline diamond, synthesized by the vapor-phase process under varying conditions, on the electron radiation characteristics of the emitters. These results have led to clarification of the optimum vapor-phase synthesis conditions for diamond for high-function emitters. The techniques utilizing focused ion beams have also advanced to develop thin polycrystalline diamond films for emitters which correspond to the image elements of quality for television. For electron emitters, a structure prepared by implantation without using a high electrical field is proposed, and the device mechanisms involved are clarified. (NEDO)

  11. Research on natural gas fuel injection system. Development of high-performance pressure regulator; Tennen gas yo nenryo funsha system no kenkyu kaihatsu. 1. Tennen gas nenryo funshayo no koseino regulator kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kato, S; Ishii, M; Takigawa, B; Makabe, K; Harada, S; Ono, H [Nippon Carburetor Co. Ltd., Tokyo (Japan)

    1997-10-01

    With the aim of further reducing the exhaust emissions of natural-gas vehicles, vigorous research and development work is under way today on multi point gas injection (MPGI) system. In this studies, a high-performance pressure regulator, which is one of the main components of this MPGI system, has been newly developed. The results showed that a significantly better accuracy of the regulated pressure level using this regulator was obtained under the wide range of operating conditions, including instantaneously greater changes of fuel flow rate. In addition, the advanced studies of gaseous fuel injectors (GFIs) would be also conducted. 4 refs., 8 figs.

  12. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloy'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    A proposal was given on a new processing process to use Ni-group super alloy, and elucidation was given on super plasticity phenomenon by using non-destructive tests. The Ni-group super heat-resistant alloy Mod. IN-100 subjected to different preforms by means of extrusion was given a super plasticity test at 1,050 degrees C to derive total elongation and 'm' value. As a result, it was disclosed that a material annealed for one hour at 1,070 degrees C after extrusion of 70% at 1,100 degrees C possesses the maximum 'm' value in the vicinity of 2.0 times 10{sup -2}s{sup -1}. The largest key to the new processing method is to improve the nature of the material, in which the plasticity manifestation velocity is accelerated by ten times to the order of 10{sup -2}s{sup -1} as described above. In addition, forging of IN-100 was made possible by using the ordinary forging equipment with the use of two-fold measures. The measures consist of maintaining temperature of IN-100 during casting by heating the die material to about 600 degrees C, rather than keeping it at a constant temperature, and then packing IN-100 in S35C steel material to accommodate the temperature decrease during casting inside the S35C pack. Thus, a processing method was made practical, eliminating need of the forging process to compress and solidify powder itself, that is the extrusion process. (NEDO)

  13. Development of advanced heat pump (2). Prelimirary test of two-stage compression heat pump. Koseino onreinetsu kyokyu heat pump system no kaihatsu. Dai 2 ho 2dan attsusyuku system shisakuki no yobi jikken kekka

    Energy Technology Data Exchange (ETDEWEB)

    Iwatsubo, Tetsushiro; Saikawa, Michinori; Hamamatsu, Teruhide

    1988-03-01

    A heat pump driven by electricity is one of the excellent electricity utilization systems and is promoted to be widely used. An advanced heat pump has been investigated to enlarge its applications in the field of hot water supply for domestic use which will be competitive with city gas and air conditioning in large scale buildings. An experimental unit with two-stage compression system was designed, which has the multi-function of air conditioning and hot water supply, and the trial system was fabricated. In the design, followings were considered; cooperative operations of two compressors by inverter driving, the temperature conditions of both the air for the air conditioning and the heat source, additional setting of the intermediate heat exchanger. The test operation was carried out with checking the start up procedure, the control sequence and so on. The probability of five operation modes: cooling, heating, hot water supply, cooling/hot water supply, and heating/hot water supply, were confirmed. In the mode of heating/hot water supply the hot water temperature was increased to 65/sup 0/C, the excellent performance in hot water supply was demonstrated. (21 figs, 8 tabs, 1 photo, 5 refs)

  14. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloys'. Evaluation on final research and development (first report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    The present research work has been performing research and development of the following alloys: (1) 'single crystalline alloy' , the entire alloy being composed of one crystal eliminating crystalline boundaries as an ultra heat resistant alloy with emphasis placed on improvement in particularly the creep properties, and 'particle dispersion strengthened alloy', in which ultrafine particles of oxides are dispersed uniformly; and (2) 'ultra heat resistant and tough alloy' targeted at high-temperature toughness by using Ni-group allowing ultra plasticity forging processing by micronizing crystal particles, as an ultra plastic and highly tough alloy having better processibility than conventional alloys, and 'light-weight highly tough alloy' aimed at achieving light weight and high toughness by using Ti-group. Achievements derived from the present research and development may be summarized as follows: in alloy development, alloys having performance of the world's highest level or equivalent have been developed; a manufacturing technology to make products with complex shapes has been established by using the alloy material manufacturing technology and the alloy materials developed therefrom, where prototype components of such shapes as turbine blades and turbine disks for jet engines were fabricated successfully; and the big fruit obtained was that a large number of technological experiences were acquired from this research and development. (NEDO)

  15. Achievement report for fiscal 1988 on fundamental technologies for next generation industries. Research and development on high-performance crystallinity controlled alloy; 1988 nendo koseino kessho seigyo gokin no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    With an objective to develop an alloy having excellent heat resistance, light weight, and high toughness, research has been performed on a high-performance crystallinity controlled alloy. This paper summarizes the achievements in fiscal 1988. In the research of a mono-crystal alloy manufacturing technology, casting tests were carried out on mono-crystal blades having cores of complex shape to evaluate the control technologies and the blade characteristics. In addition, mono-crystals were cast from the melting stock of the developed alloy to investigate their creep rupture characteristics. In the research of an ultra-plastic alloy manufacturing technology, alloy powder with average diameter of 80 {mu}m has become producible. The HIP-heat extruded material has achieved elongation of about 200% even in coarse powder. In the ultra-plastic processing method utilizing the ultra-alloy powder, the dual property disk was developed successfully, and the manufacturing technology was established. In the technology to cast a particle dispersed and reinforced alloy, a technology was developed to form an integrated half-cut blade with thin wall and long length. In the heat treatment technology, the band annealing conditions were elucidated on components having complex shapes, and trial production was executed on parts whose crystals are treated unidirectionally. (NEDO)

  16. NEDO Forum 2000. New energy and energy conservation introducing and proliferating project session (toward promotion of introducing new energies and energy conservation); Shin'ene shoene donyu fukyu jigyo session. Shin'ene shoene no donyu sokushin ni mukete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    The following themes were presented at this session: (1) the history and roles of the NEDO's introduction and promotion projects, (2) expectation and prospects to introduction and promotion of new energy and energy conservation technologies, (3) energy innovation in houses and buildings actively using new energies and energy conservation means, (4) works on introducing new energies by using the private finance initiative (PFI), and (5) the last resort for energy conservation promoting measures in the industrial domain (high-performance industrial furnace technologies). In Item 3, design cases intended for sustainable buildings were introduced. In Item 4, the PFI is explained as a means to use as much fund and management know-how in private sectors as possible in improving the social capitals and providing high-quality public services. In Japan, the PFI promotion law was established in July 1999 (the law concerning promotion of improvements in public facilities by utilizing funds in private sectors). Introductions are given on the wide area wastes disposal project in Kimitsu Area, the PFI model project for power generation of everyday use at Kanamachi Water Purification Plant of the Tokyo Metropolitan Water Supply Bureau, and the Omuta RDF power generation project. In Item 5, descriptions are given on a new high-performance industrial furnace using the combustion mechanism of 'high-temperature air combustion' created from preheated air at temperatures higher than spontaneous combustion temperature. (NEDO)

  17. Statistical analysis of thermal efficiency in industrial furnaces in Japan and determination of CO2 reduction amount realized by improving the efficiency; Nippon no kogyoro ni okeru netsukoritsu no tokeiteki kaiseki to sono kaizen ni yoru CO2 sakugenryo no suitei

    Energy Technology Data Exchange (ETDEWEB)

    Iwabayashi, T.; Matsuhashi, T.; Ishitani, H. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Tanabe, K. [The Energy Conservation Center Japan, Tokyo (Japan); Tanaka, R. [The Japan Industrial Furnace Manufacturers Association, Tokyo (Japan); Takashima, T.

    1997-01-30

    Analyses and evaluations were given on heating furnaces and heat treatment furnaces used in the Japanese steel and iron industry to calculate amounts of energy and CO2 that could be reduced by introducing a new furnace. The analyses have derived factors affecting thermal efficiency of the heating furnaces by using regression analysis. Discussions were given on a high-temperature air combustion system and a stored heat combustion system as new furnace technologies. As a result, it was disclosed that the current fuel consumption could be reduced to about 40% to 80% only by performing air pre-heating ideally and suppressing heat loss from furnace walls. This concept is sufficiently payable in terms of economy. It was also revealed that fuel consumption could be reduced to about 12% to 36% and CO2 discharge could be reduced in proportion with reduction in the fuel consumption, if ideal preheating can be carried out on materials to be heated. Furthermore, a result was obtained that the present thermal efficiency of 26.86% in nonferrous industries such as for copper and aluminum could be increased up to 53.37%. 10 refs., 19 figs., 1 tab.

  18. Fiscal 1995 report on the survey of making models for introducing petroleum substituting energy systems. 2; 1995 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa). 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In the promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. guidance for introducing energy systems which meet with features of the buildings and courses for how to construct infrastructures of towns or cities in case of development, redevelopment, etc. In fiscal 1995, each of the petroleum substituting energy systems was studied more detailedly, and the trend of building facilities for the introduction was studied and arranged. Energy systems by the following were set up paying attention to energy sources, energy conversion and energy transportation as factors composing a petroleum substituting energy system: photovoltaic power generation, use of solar energy, use of wind energy, use of geothermal energy, use of biomass energy, use of waste, use of temperature difference energy, cogeneration, load levelling, wide-area energy supply, etc. Also studied and arranged were energy demand, location, the recent trend, the point of introduction of energy systems, examples of introduction, etc. in relation to indoor sport facilities, hospitals, hotels, multiple dwelling apartments, commercial facilities, offices, plants, etc. 52 figs., 55 tabs.

  19. Survey of the measures to be concretely taken for CEV introduction/spread in the region; Chiiki ni okeru CEV donyu fukyu no tame no gutaiteki hosaku ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the Hanshin/Harima region where CEV introduction/spread are expected and there is a great pervasive effect, survey/study were conducted to plan the construction of facilities for natural gas vehicle fuel supply in future. In the survey, the paper summed up the state of CEV spread in the Hyogo prefecture, the state of construction of fuel supply facilities, etc. Further, by the questionnaire survey, the needs for construction of fuel supply facilities were grasped, and the intention of introducing natural gas vehicle was sounded out. In the study of a wide-area construction plan for natural gas fuel supply facilities, the Hanshin/Harima region was divided into zones based on geographical conditions, traffic system, etc., and the number of the needed fuel supply facilities was calculated which corresponds to the targeted number of natural gas vehicle introduction set up by the nation. Moreover, by the questionnaire survey, the needs for fuel supply facilities were grasped, and a method for setting up the order of priority in the construction was determined/proposed. Through the study of these, a manual was made out which is usable for the CEV introduction and the construction plan for natural gas fuel supply facilities in other regions. (NEDO)

  20. FY 1998 annual report on the survey on development, introduction and promotion of urban type multipurpose geothermal utilization techniques; 1998 nendo toshigata tamokuteki chinetsu riyo gijutsu no kaihatsu, donyu, sokushin ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Introduction of geothermal heat pump systems, which depend on temperature differential, is investigated for urban areas, which have large energy demands. Results of the surveys on the current situations of geothermal heat pump (GHP) systems indicate that they have already numbered 300,000 units in USA and totaled more than 50,000 units in Switzerland and Northern European countries, and that they are increasing at an annual rate of higher than 10%. The results also indicate that introduction of these systems are well feasible in Japan, which generally has better topographical conditions than American and European countries, and the GHP system with vertical ground heat exchanger is investigated for its topographical and environmental considerations. These systems could annually abate approximately 52 million tons of CO2 (4.3% decrease), if disseminated to all households. They are also expected to help control the heat island phenomenon, and reduce peak power consumption. The technological problems to be solved before these systems are massively disseminated including development of small scale drilling rigs and preparation of drilling manuals. System standardization and introduction of subsidy systems are also needed to massively disseminate these systems. (NEDO)

  1. Fiscal 1998 research report. Feasibility study on next-generation environment-friendly urban transport systems; 1998 nendo chosa hokokusho. Jisedai kankyo kyosei toshi kotsu system donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research arranges recent public transport system technologies such as LRT, and clarifies their technical issues to be overcome and developmental courses, and the improvement effect of their energy efficiency and CO{sub 2} reduction effect by such measures to contribute to development of next-generation public transport systems. The outlines and features of LRT, monorail/trolley bus and AGT as existing public transport systems are arranged. In the EU, development of tramways using rubber tires is in promotion. The concept of a next-generation environment- friendly urban transport system is prepared based on features of every public transport system. Since a trolley system causes traffic congestion and environment deterioration, introduction of an independent transport system with fuel cell is necessary in the future. The technical issues and solutions for construction of the next-generation transport systems are analyzed. Fuel cell and ITS are important candidates. Substitution of the next-generation transport system for existing buses showed a CO{sub 2} reduction effect of 3.91 Mton/y in Japan. (NEDO)

  2. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (civil engineering); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Doboku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys and discussions were given on the external accreditation system for engineer education such as in universities and other organizations. In the field of civil engineering, a special sub-committee was organized, and in advance to a trial examination, surveys and discussions were executed by participating in the actual examination of the engineer educational program at the engineering department of Auckland University, and by participating in the ABET trial examination by the civil engineering department of Kansas State University and the engineering department of Stanford University in the U.S.A. The trial examination was performed upon selecting the engineer educational programs of the civil engineering department of Kinki University and Tottori University. This paper describes the fundamental policies on the educational program examination work for the field of civil engineering, the self-assessment under the educational program, the direction of engineering qualification and educational accreditation, the fundamental concept of examination and accreditation and evaluation process, the works done by the civil engineering section of the science and engineering department of Kinki University, and the works done by the civil engineering section of the engineering department of Tottori University. (NEDO)

  3. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (electronic information communications); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Denshi joho tsushin)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys were performed on the external accreditation system for engineer education such as in universities and other organizations. In the field of electronic information communications, a committee to correspond to JABEE was established to perform system build-up, where the discussions were advanced. This field was classified into the following four specified areas: general aspect of electric/electronic/information communication engineering, electronics, information communications, and information systems. A supplementary explanation was given on the educational contents except for the information systems, based on which the self-assessment criteria and the evaluation table (for trial use) were prepared. For the examiner training, instructors were invited from ABET in the U.S.A., and training meetings were held. In addition, two committee members were sent as observers to the examinations being carried out at ABET. The trial experiments were conducted for the information communications program at the engineering department of Niigata University, and the electronic system engineering class at Sendai Radio Wave Industrial College. This paper summarizes the results of the examinations. (NEDO)

  4. Fiscal 1999 report on basic research for promotion of joint implementation programs. Basic research on introduction of energy saving facilities into Bulgaria's Kremikovtzi Steelworks; 1999 nendo Bulgaria Kremikovtzi seitetsusho no sho energy setsubi donyu kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The plant undergoes a survey for higher energy efficiency, pursuant to the COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) protocol. Dry quenching and coal moisture control are investigated for the coke oven; exhaust heat recovery and high efficiency ignition burner for the sintering machine; top pressure recovery power generation and hot stove exhaust heat recovery for blast furnace; gas recovery for the converter; scrap preheating for the electric furnace; continuous casting and soaking pit efficiency improvement for the blooming process; hot charge and heating furnace efficiency improvement for the hot strip mill reheating furnace; and furnace efficiency improvement and hydrogen annealing applicability for the annealing furnace. The energy saving effects of the above are calculated under conditions that one more of the same be added to the continuous slab casting unit and that a continuous bloom casting unit be constructed for the continuous casting of the whole, and that hydrogen annealing be adopted. A reduction of 141,900toe/year is to be achieved, which occupies 6% of the energy consumption of the whole steelworks. A greenhouse gas reduction of 333,600t-CO2/year is feasible. Now that privatization is under way for business reconstruction and rationalization, suggestions will be presented in consideration of the order of priority of investment recovery effects with attention paid to the privation program. (NEDO)

  5. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (general); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Zentai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, trials and discussions were performed on the external accreditation system for engineer education such as in universities and other organizations. The current fiscal year has performed the trials of examination and accreditation at 19 universities and for 20 programs covering eight fields including chemistry, machinery, civil engineering, electrical, electronic, information communications, information processing, materials, resources and agricultural engineering. In performing the trials, the purpose and the basic policies were identified, the guidebook for actual examinations was prepared, and the program check book and the trial examination report were also compiled. Two assembly training meetings were held to train about 130 examiners, of which 65 examiner chiefs and examiners have participated in the trials for 20 schools to work for the examination. As a result of the trials, the training was found capable of having served for improvement of the engineer education program in high-level education institutions, and improvement of the accreditation criteria and examination methods to establish the external accreditation system. (NEDO)

  6. Surveys on awareness and needs of industries to external accreditation system in engineer education; Gijutsusha kyoiku no gaibu ninteiseido donyu ni taisuru sangyo kai no ioshiki to needs ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In certifying the engineer educational programs at advanced educational organizations, questionnaire and visiting surveys were performed to identify the awareness and needs of industries, and reflect the results to the external accreditation system. The questionnaire survey was conducted on 1,100 engineers acting in the wide technical areas. Effective replies were obtained from 528 engineers. The visiting survey was executed on different business areas and operations. The result of the survey revealed that, in the awareness related to international universality of the engineer education and engineer qualification, 87% answered that they feel they need them, but the cognition rate on the accreditation system has not reached even 50%. In hearing the opinions from representatives in the industries, they indicated that it is not correct to link the certification course of JABEE directly to the engineer qualification; international applicability of JABEE with America is fine, but defining the engineers who desire to come from Asian countries and work in Japan is necessary; the engineer education has its importance shifting from quantity to quality and specialization, but on the other hand diversity is also demanded; and criteria would be necessary to guarantee the minimum required knowledge and capability. (NEDO)

  7. Fiscal 2000 survey report. Refuse-fueled power generation introduction technology, etc. Part 2. Survey of general refuse-fueled power generation; 2000 nendo chosa hokokusho. Haikibutsu hatsuden donyu gijutsu chosa to - Ippan haikibutsu hatsuden chosa Part 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Surveys were conducted of the effect on waste quality of the Law for Promotion of Sorted Collection and Recycling of Containers and Packaging, diffusion of PFI (private finance initiative) involving refuse-fueled power generation, recycling of slag, etc. Questionnairing was conducted for the survey of the effect on waste of the effectuation of the recycling law, size of population supplying the waste and the amount actually incinerated, actually measured data of the composition of incinerated waste, assorted collection programs, amount reducing measures, and the like. Studies were made as to if the empirical formulas applied in the survey of the preceding fiscal year would remain applicable after the coming into force of the recycling law. In the survey of PFI popularization, it was found that the rate it was taken into account for concrete projects was so low as 13.8% though most of the autonomous bodies had cognizance of PFI. It was requested that it be clearly stipulated that 'the conventional subsidies and grants apply also to PFI projects.' In the survey of conversion of residue into molten slag in refuse-fueled power generation and its reuse, four kinds of slag specimens were examined for physical properties, elution, and analyzed for ingredients, and then it was found that they posed no problems like heavy metal elution. (NEDO)

  8. FY 1994 report on the survey and research of introduction, promotion of proliferation and guidance on new energy introduction. Pt. 2; 1994 nendo shin energy donyu fukyu sokushin shido ni kansuru chosa kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Survey, collection and analysis were performed on different items of information required for new energy technologies. Studies were carried out to structure a system to support smooth execution of technical guidance and consultation. Among the project areas for field tests on photovoltaic power generation systems for public facilities, measurements were executed on hourly power demand in facilities in snowy and cold districts with little data available. In putting different items of information into a database, data were collected and put into order for the following items: statistics on average value for ten years of insolation time in 842 locations nationwide, calculation of insolation on slanted surface at the insolation measuring points (slanting angles and insolation on the slanted surface at which energy amount available for power generation is maximized in a year, as obtained by estimating the insolation on horizontal surface from the insolation duration), and expansion and addition of the introduction examples. Specifications for solar cell modules and inverters were classified and put into order, and so were on types, specifications, and product descriptions for photovoltaic power generation systems for individuals' houses. The aid system structured in the previous year was discussed for improvement, and new information was put into a database to improve the aid system. (NEDO)

  9. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (information); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Joho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys and discussions were performed on the external accreditation system for engineer education such as in universities and other organizations. In the survey on the information field, a trial was attempted on the information related course at Kyoto University and Osaka University based on the accreditation criteria discussed with an objective of establishing the external accreditation system. The trial was performed on computer science for Kyoto University and software engineering for Osaka University. The activity has provided the examiner side with an opportunity to actually experience the accreditation work, and the examiners had a feeling that the work can help improve the education. The side receiving the accreditation indicated problems in the present system including the concern about the system becoming a mere shell. In addition, participation in the accreditation examiner training work for the information field in the U.S.A. has provided useful information such as thoroughgoing observation of the duty of confidentiality. (NEDO)

  10. Report on results 1998. Research and development on high-temperature superconducting flywheel power storage (investigation on system introduction); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (system donyu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    In introducing high-temperature superconducting flywheel power storage equipment to an electrical power system, adaptability is examined and evaluated concerning secondary effect that can be expected while a load leveling function is maintained. The 1998 plan is such that the functions and usages other than the load leveling are put in order for such equipment, and that the effect/adaptability in the case of the introduction into the power system is evaluated by means of simulation and literature studies. The high-temperature superconducting flywheel power storage equipment may be used for such purposes as energy adjustment for a short time, system voltage adjustment and emergency power source, other than the load leveling, on the basis of the characteristics that enable high speed control of active/reactive power and storage/release of energy. Enumerated, as the effects obtainable in introducing these uses into the power system, are enhancement in system stability, improvement in voltage stability, improvement in instantaneous voltage drop, maintenance of system frequency, compensation of fluctuating load, countermeasures against power outrage, and output leveling of intermittent power sources, and these effects were examined. (NEDO)

  11. Effect of heat-insulating wall on input energy of a photovoltaic/solar/air-heat system for a residence; Jutaku no kodannetsuka ni yoru taiyoko netsu/taiki netsu system no donyu energy sakugen koka

    Energy Technology Data Exchange (ETDEWEB)

    Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru College of Technology, Kyoto (Japan)

    1996-10-27

    A proposal was made to introduce a photovoltaic/solar/air-heat system which positively utilizes natural energy in order to curtail consumption of fossil energy, corroborating that the system has greatly reduced energy input in the primary energy level in a house. This paper examines the effect of curtailment of energy input in the case of reducing the load of air conditioning through the high heat insulation of a house. The energy input was evaluated by calculating additional equipment energy needed newly for the high heat insulation. The system performance and the energy load varied greatly depending on weather conditions. The subject system consisted of solar cells, inverter, heat concentrator, heat storage tank, heat pump and gas hot-water supply device. The thickening of the insulation sharply reduced heating load in the house, thereby decreasing fuel energy substantially. An insulation material of 100mm thick was capable of reducing energy input by 16-23% compared with that of 50mm thick. 5 refs., 5 figs, 3 tabs.

  12. FY 1994 report on the survey and research of introduction, promotion of proliferation and guidance on new energy introduction. Pt. 2; 1994 nendo shin energy donyu fukyu sokushin shido ni kansuru chosa kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Survey, collection and analysis were performed on different items of information required for new energy technologies. Studies were carried out to structure a system to support smooth execution of technical guidance and consultation. Among the project areas for field tests on photovoltaic power generation systems for public facilities, measurements were executed on hourly power demand in facilities in snowy and cold districts with little data available. In putting different items of information into a database, data were collected and put into order for the following items: statistics on average value for ten years of insolation time in 842 locations nationwide, calculation of insolation on slanted surface at the insolation measuring points (slanting angles and insolation on the slanted surface at which energy amount available for power generation is maximized in a year, as obtained by estimating the insolation on horizontal surface from the insolation duration), and expansion and addition of the introduction examples. Specifications for solar cell modules and inverters were classified and put into order, and so were on types, specifications, and product descriptions for photovoltaic power generation systems for individuals' houses. The aid system structured in the previous year was discussed for improvement, and new information was put into a database to improve the aid system. (NEDO)

  13. Introduction of anti-rolling active vertical fin and its application to maneuverability for displacement-type super high speed ship. 2nd Report.; Haisuiryogata chokosokusen no yokoyure seishiyo active suichoku fin no donyu to sojuseieno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Hirayama, T; Saito, Y [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Niihara, Y [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1997-12-31

    Discussed herein are the effects of vertical fin projecting downwards from the bottom of a displacement-type superhigh-speed ship, installed to improve its transverse stability and turning ability. The system for simultaneously controlling rudder and vertical fin by the optimum regulator was studied for maneuverability in directional following waves and smooth water, and maneuverability was simulated numerically. A ship is greatly rolled and sloped when running in waves. It is found that the vertical fin shows a high anti-rolling effect when the ship runs straight. The optimum regulator greatly improves maneuverability in waves, reducing rolling by 92%. Increased rolling with the vertical fin, observed in the previous study in directional following waves, is found to be due to the rudder. The optimum position of the fin is determined to control transverse sloping of a turning ship in a superhigh-speed region. 21 refs., 12 figs., 4 tabs.

  14. Fiscal 1995 survey report on the environmentally friendly type coal utilization system introduction support project. Verification project on the circulating fluidized bed boiler; Kankyo chowagata sekitan riyo system donyu shien jigyo. Junkan ryudosho boiler ni kakawaru jissho jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    In relation to the circulating fluidized bed boiler which reduces the amount of sulfur oxides emitted in coal utilization, a verification project was carried out on installation of the equipment and spread activity in China and the Philippines contributing to the control of environmental pollutant associated with coal utilization and the effective use of energy. At the Fanshan area, installed was a 10t/h internal circulating fluidized bed boiler. At the performance test, coal includes around 7% of impurities such as stone, and the impurities should be excluded continuously at the time of actual run. Therefore, the boiler efficiency had to be changed from 89.5% to 85.8%. Further, power generation facilities have not yet been finished, and the overall operation of boiler turbine has not been executed. At the Zibo area, a 30t/h external circulating fluidized bed boiler was installed. The boiler efficiency reached 86.1%, over the targeted value. At the Batangas area in the Philippines, a 10t/h internal circulating fluidized bed boiler was installed. The boiler efficiency reached 85.8%, over the designed value. About the coal produced in the Philippines, slagging was feared, but the combustion state was favorable. 82 figs., 21 tabs.

  15. FY 1994 Report on the results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers; 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu saiteki donyu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Described herein are the FY 1994 results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers or the like. The necessary economic conditions for introduction of a fuel cell system to be competitive with the conventional system which individually supplies electric power and heat are 250,000 yen/kW as the construction unit cost, 0.10m{sup 2}/kW as the installation area, 5 years as the cell body life, use of an inexpensive fuel gas (2 to 6 yen/Mcal). Moreover, it is an indoor system which shall have the operational characteristics to follow daily demand fluctuations while operating under the optimum conditions in the urban redevelopment area considered. A 5,000kW-class fuel cell plant burning fuel gas (2 yen/Mcal) will need a total floor area of approximately 400,000 m{sup 2} in an energy-intensive office type demand area. These conditions shall be met in order to economically introduce the 5,000kW-class plant. It is also necessary to compare the plant with the competitive cogeneration plants. The specifications for the prototype now under consideration are sufficient for the energy-saving effect, and it is premised that these specifications and characteristics are secured. (NEDO)

  16. Fiscal 1999 geothermal energy development promotion survey. Report on survey of introduction of techniques for predicting impact on hot springs; 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Onsen eikyo yosoku shuho donyu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-08-01

    In an effort to find guidelines on how to proceed with geothermal energy development so that it may coexist with hot springs, investigations are conducted into cases of impacts on hot springs imposed by geothermal energy development activities. An impact is judged to exist when geothermal development results in a decrease or depletion of pumped or spontaneously welling hot spring water, change in the concentration of dissolved chemical ingredients, fall in water temperature, or in an increase in the amount of discharged steam. Keyword-aided retrieval of data from databases is performed, and geothermal magazines are referred to for information. There are articles reporting impacts imposed by geothermal development on hot springs in the Palinpinon area (Philippines) and 12 others and in the Corwin Springs area (U.S.) and 13 others. These articles carrying outlines and impacts of geothermal development are collected, put in order, and analyzed. Cases in which such impacts are found to exist are categorized into four groups and, in each group, episodes are differentiated from each other by the type of mechanism linking the aquifer and the reservoir which is the object of development. (NEDO)

  17. Introduction of anti-rolling active vertical fin and its application to maneuverability for displacement-type super high speed ship. 2nd Report.; Haisuiryogata chokosokusen no yokoyure seishiyo active suichoku fin no donyu to sojuseieno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Hirayama, T.; Saito, Y. [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Niihara, Y. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1996-12-31

    Discussed herein are the effects of vertical fin projecting downwards from the bottom of a displacement-type superhigh-speed ship, installed to improve its transverse stability and turning ability. The system for simultaneously controlling rudder and vertical fin by the optimum regulator was studied for maneuverability in directional following waves and smooth water, and maneuverability was simulated numerically. A ship is greatly rolled and sloped when running in waves. It is found that the vertical fin shows a high anti-rolling effect when the ship runs straight. The optimum regulator greatly improves maneuverability in waves, reducing rolling by 92%. Increased rolling with the vertical fin, observed in the previous study in directional following waves, is found to be due to the rudder. The optimum position of the fin is determined to control transverse sloping of a turning ship in a superhigh-speed region. 21 refs., 12 figs., 4 tabs.

  18. Research and development of system to utilize photovoltaic energy. Study on the scenario for the diffusion of photovoltaic power generating systems; Taiyoko hatsuden riyo sytem no kenkyu kaihatsu. Taiyoko hatsuden donyu fukyu scenario sakusei no tame no chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on a survey to prepare scenario for the diffusion of photovoltaic power generating systems. Introduction target planned with help of a diffusion simulation was verified by calculations using simulation models. The calculations made the following points clear: facility costs and power generation costs for photovoltaic power generation systems, amount of introduced photovoltaic power generation systems, number of facilities introducing photovoltaic power generation systems, policy cost to achieve the target, annual power generation amount, oil substituting effect, carbon dioxide reducing effect, and market sizes. Power generation cost in fiscal 2000 would drop down to 53 yen per kWh in new installation in independent houses and down to 31 yen per kWh in systems used in schools. These reductions are the result of progress in mass production as a result of positively implementing the aiding policies. The required diffusion aiding policies revealed from the simulation results include expansion of subsidy operations for house construction, introduction of the systems into public facilities performed by public organizations, aid to system introduction into private business entities, subsidy to facility investments, and enforcement of power purchase institutions. 3 figs.

  19. Research program for environmentally-friendly coal utilization system. Follow-up project for simplified desulfurizers (Weifang Chemical Industry Works); Kankyo chowagata sekitan riyo system donyu shien jigyo. Kan`i datsuryu setsubi ni kakawaru follow up jigyo (Weifang kakosho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To suppress the emission of environmental pollutants from coal utilization in China and to contribute to stable security of Japan`s energy, demonstration of clean coal technology and consolidation of diffusion base to be introduced into China have been promoted. Demonstration program for diffusing simplified desulfurizers has been promoted. For accelerating the achievement, experts of desulfurizers were delegated to Weifang Chemical Industry Works, to support the program. Exhaust gas is introduced from boiler via water spray dust remover, suction fan and centralized stack into absorption tower of the simplified wet-type desulfurizer. In the ascending process, the exhaust gas contacts with absorbent, to remove SO2 and dust. The absorbent is blasted up through the spray nozzle. The absorbent is oxidized by the air into sulfate ion in the liquid chamber at the lower part of tower, and neutralized by hydrated lime to form gypsum. Through the continuous operation for two years, understandings were remarkably increased. However, good treatment of the tax system is required for further diffusion. Though there are no problems for ordinary start and stop, emergency operation is insufficient. There are some problems in the maintenance due to the delay of finding failures. 16 figs., 1 tab.

  20. Fiscal 1994 report on the survey of making models for introducing petroleum substituting energy systems; 1994 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    In the promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. appropriate and concrete guidance for introducing energy systems which meet with features of the areas and buildings and courses for how to construct infrastructures of towns or cities in case of development and redevelopment. Recently, also in local governments, etc., there are seen attitudes toward positive study of introduction of energy conservation systems and petroleum substituting energy systems in case of redevelopment, and the situation is that the spread and expansion are expected by giving appropriate guidance for the introduction. Accordingly, the study makes analyses of the trend and characteristics of developmental projects and makes/arranges models of promising petroleum substituting energy systems, aiming at contributing to promotion of guidance for the introduction to local governments, entrepreneurs, etc. Approximately 20 models of petroleum substituting energy systems were made which are thought to be promising. For each, the following were arranged: outline of system, introduction target, introduction effects, the point of promotion of the introduction, related subsidy systems, actual results, etc. 22 figs., 34 tabs.

  1. Fiscal 1997 survey report. Preparatory survey for a manual on the introduction of high efficiency thermal utilization systems; 1997 nendo chosa hokokusho. Kokoritsu netsu riyo system donyu manual no sakusei choa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To cope with the energy issue and global environmental issue, it is necessary to forcibly promote energy conservation. In the light of the present situation that in Japan only 1/3 of the primary energy consumed is effectively used, policies are being prepared for promotion of the introduction of high efficiency thermal utilization systems including `a project for formation of the environmentally friendly type energy community` promoted by NEDO. However, it is hard to say that the introduction is being actively promoted. The cause is that they do not fully understood the present status of high efficiency thermal utilization systems, procedures for introduction, subsidy system, etc. Therefore, a manual was made to present to self governments and enterprisers who are planning to introduce the system. To be concrete, there are the six systems: cogeneration use thermal supply system, unused energy use thermal supply system, heat storage use thermal supply system, waste use thermal supply system, plant surplus energy use thermal supply system, and cascade type thermal supply system. 28 refs., 38 figs., 42 tabs.

  2. FY 1998 annual report on the introduction/dissemination working group. 19th R and D activity report; 1998 nendo donyu fukyu jigyo bunkakai. Dai 19 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    Summarized herein are the FY 1998 R and D activities by the introduction/dissemination working group, extracted from the 19th R and D activity report by NEDO. Mr. Yamaho, a NEDO's director, reports (General situations of the new energy introduction promotion department). The R and D project results include those of renewable energy sources, such as the results of the field test and supporting projects for solar light power generation, wind power generation and solar heat utilization; and those of recycling type energy, such as the results of the field test projects for power generation by wastes and fuel cells, and the results of the projects for district heat supply by co-generation systems. The other results presented include those of the projects for dissemination of clean energy vehicles, supporting new energy entrepreneurs, promotion of introducing district new energy, drawing visions for district new energy, field tests for introducing high-performance industrial furnaces, modeling for introducing facilities for rationalized use of pioneer energy, promotion of disseminating ice-aided, heat-storage type air conditioning systems, and promotion of introducing decentralized gas-aided air conditioning for existing small- to medium-sized buildings. (NEDO)

  3. Report on FS survey for project of introduction of highly energy-efficient trolley buses into the Mexico Metropolitan Area in FY 1997; 1997 nendo chosa hokokusho (Mexico city eno sho energy gata trolley bus donyu project FS chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Traffic jam and air pollution by automobiles are currently getting severe in the Mexico Metropolitan Area. Trolley buses were introduced for improving the environment more than ten years ago. Vehicles become too old for use, and their energy efficiency is low. In this project, 200 highly energy-efficient trolley buses are introduced to replace old inefficient trolley buses, which results in the improved traffic convenience in the City and enhanced energy efficiency. The new energy-efficient trolley buses are made of energy-efficient control VVVF inverters produced and exported by MELCO (Mitsubishi Electric Corporation), energy-efficient motors by MELMEX (Mitsubishi Electric Corporation, Mexico), and bodies by MASA which is a major manufacturer of bus bodies. The objective of this research is to analyze the background of introduction of new energy-efficient trolley buses and the effects of the present project. The results of analysis are going to be utilized for future promotion of the Joint Implementation and Clean Development Mechanism. 30 refs., 30 figs., 24 tabs.

  4. FY 2000 report on the investigational study of the introduction/spread of clean energy vehicles for transportation business use; 2000 nendo chosa hokokusho. Unso jigyo yo clean energy jidosha no donyu fukyu ni kakawaru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A comparative study of the cost effectiveness in improvement of emission gas was made between the diesel particulate filter (DPF) which is studied as measures against toxic emission gas from the vehicles already sold and the compressed natural gas (CNG) vehicle which has a large number of spread among clean energy vehicles. In the trial calculation, 18 cases were set up using measures by year against diesel car emission gas, use period and annual running distance as valuables. As a result of the study, the following conclusions were obtained. At the present time, when the vehicle price dropped approximately 40% from that at the beginning of the introduction, the cost effectiveness of CNG vehicle is larger than that of diesel car with DPF. Since the unit price of natural gas is comparatively higher than that of light oil, the longer the annual running distance is, the smaller the cost effectiveness of CNG vehicle is than that of diesel car with DPF. The durability period of DPF is considered not so long, and therefore, the longer the use period is, the larger the cost effectiveness of CNG vehicle is than that of diesel car with DPF. (NEDO)

  5. FY 2001 report on the results of the trend survey of introduction of clean energy vehicle for the transport industry; 2001 nendo unso yo clean energy jidosha no donyu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    Survey/analysis were made on the details of the plan on the leading introduction of clean energy vehicle by 632 transporters who applied for the project on promotion of clean energy vehicle in FY 2001. As a result of the survey, the following were made clear. The clean energy vehicles to be planned to be introduced by transporters are all natural gas vehicles. The transporters planning the leading introduction are mostly in large cities and are spreading also in the periphery. Fifty three percent of the transporters predicts that the predicted average running distance of the clean energy vehicle to be introduced is the same as those of the vehicles they owns, and 39% predicts that it is shorter. About the form of utilization, they use it overwhelmingly for the regional collection/delivery. It is considered that the improvement in running distance per 1 fuel filling of clean energy vehicle will contribute to the spread. Fuel supply stations that the clean energy cars to be introduced use concentrate in the good location. It is necessary to strongly promote preparation of the infrastructure. (NEDO)

  6. NEDO Forum 2001. Session on New Energy/Energy Conservation Popularization Project (Let's walk and save energy - Let new energy run on its course); NEDO Forum 2001. Shinene shoene donyu fukyu jigyo session (aruko shoene hashiro shinene)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Professor Kashiwagi of Tokyo University of Agriculture and Technology in his keynote address, entitled 'How the popularization of new energy and energy conservation should be in the future,' discussed energy conservation measures, new energy measures, fuel conversion, natural gas, and atomic energy, and disclosed his long-term outlook of energy supply and demand. NEDO in its achievement report mentioned a simulation on the smooth interconnection of distributed power sources such as wind power sites to a commercial power system. It reported also that, under its 3-year high performance industrial furnace field test project started in 1998, 167 furnaces, including heating furnaces, ladles, heat treatment furnaces, melting furnaces, and gas treatment furnaces were converted into high performance industrial furnaces capable of high temperature preheated air combustion near 1000 degrees C and that the conversion brought about a great reduction in energy consumption and in carbon dioxide gas and nitrogen gas emissions. (NEDO)

  7. FY 2000 Feasibility study on the environmentally-friendly coal utilization systems as part of the international project for coal utilization measures. Feasibility study on supporting introduction of the environmentally-friendly coal utilization systems in Vietnam (Model project for introduction of advanced coal preparation systems); 2000 nendo kokusai sekitan riyo taisaku jigyo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa jigyo Vietnam ni okeru kankyo chowagata sekitan riyo system donyu shien jigyo (kodo sentan system donyu model jigyo kanosei chosa jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    The feasibility study was conducted on a model project in Vietnam, aimed at solving the environmental pollution problems resulting from use of coal by demonstrating and disseminating the Japan's environmental technologies in the Southeast Asian countries. The feasibility study was conducted for the Cua Ong Coal Preparation Enterprise, which has the largest coal preparation capacity in Vietnam and port facilities. It is treating raw coal from 10 coal mines for classification and preparation, and shipping coal of various types that meet the standards for domestic use and export. The survey results point out that unrecovered coal remains in waste water discharged from the coal preparation plants to pollute the sea area, and that quantity of the refuse increases because of the unrecovered coal it contains. The environmental technologies needed to introduce include modification to variable wave pattern type jigging separator, refuse height measuring instrument and automatic controller, circulating heavy medium gravimeter, highly functional settling pond, and flocculent facilities. (NEDO)

  8. Fiscal 1998 achievement report on regional consortium research and development project. Venture business fostering regional consortium in its 2nd year--Creation of key industries (Development of processing of new structure-designed high-performance polymer alloy); 1998 nendo shinkina kozo seigyo koseino kobunshi alloy no seikei kako ni kansuru kenkyu kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are exerted to make novel recyclable polymer alloys excellent in material characteristic and to develop a technology for processing them, for which liquid crystalline polymers equipped with a self-alignment capability are combined with thermoplastic resins. In the research on the alloying of polyethylene terephthalate (PET) and liquid crystal polymers (LCP), studies are conducted about inorganic nucleating additives, thermostabilizers, and mold releasing lubricants, and a success is attained in the manufacture of excellent alloyed pellets. In the injection molding of alloys of PET and LCP, a product is obtained, among those produced with the rate of LCP varied, which behaves excellently even at a high resin temperature of 285 degrees C. It is found about PET/LCP alloys that improvement is achieved with additional LCP in terms of the warpage temperature under load, bending property, strength, and dimensional stability upon exposure to heat. In the study of the response of LCP-diffused PET to a process demanding distortion, an injection-molded product containing 10-20% of LCP is found to exhibit excellent ductility. It is also found that PET/LCP alloys may be cut and machined easily and that therefore their crushing for the recycling purpose will be easy. (NEDO)

  9. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D high performance flat panel display technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / koseino flat panel display gijutsu no sogo kaihatsu kenkyu (daiichi nendo ) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    One of the subjects in technology supporting the highly information-oriented society which will develop and diversify toward the 21st century is the construction of high grade man/machine interface. For it, high precision/high luminance/energy saving/thin plane displays are strongly requested. This R and D is to indicate models of systematical development in the region of element technology individually existing in the Shikoku area by forming a regional consortium in the industry/universities/government. Creation of new industries by gathering display related enterprises is a first step in a plan to realize `Display Island Shikoku.` As a concrete target, with the use of high-tech diamond semiconducting technology, a development is conducted of the high performance flat panel display using the negative electron affinity (NEA) electron emitter which drastically solves the problems such as luminance, visibility angle and response speed, the subjects on the commercialized liquid crystal flat panel display. 16 refs., 45 figs., 8 tabs.

  10. Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.1). Achievement report on development of novel high-performance dry type desulfurization agent made from coal ash; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.1). Sekitanbai wo genryo to suru shinki koseino kanshiki datsuryuzai no kaihatsu to riyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop a technology of using quicklime instead of slaked lime for a reduction in desulfurization cost, based on the technology of the coal ash utilizing dry type desulfurization device operating on coal ash, slaked lime, and gypsum, as hardened by hydration. Activities are conducted in the three fields of (1) basic study, (2) desulfurization agent bench-scale manufacturing test, and (3) study for putting the technology to practical application. In field (1), the basics are studied of the lime slaking process in the manufacture of a dry type desulfurization agent from quicklime, the mechanism is elucidated of the generation of active desulfurization substances, and effective utilization is studied of the desulfurization agent after use. In field (3), conceptual designs are prepared, cost efficiency of desulfurization systems are evaluated, simplified absorption systems are studied, and the trends of dry type desulfurization systems are surveyed. The cost of desulfurization under development is equivalent to that of the wet type method (limestone-gypsum system) when the used desulfurization agent is discarded, and is approximately 60% of the wet type method when the whole amount is effectively utilized. (NEDO)

  11. Studies on high-performance ceramic heat exchanger for ultra high temperature. 2nd Report. Heat transfer of finned tube bundle immersed in fluidized bed; Chokoon`yo koseino ceramic netsu kokanki ni kansuru kenkyu. 2. Ryudo sonai no rin kangun no netsudentatsu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Himeji, Y; Kumada, M [Gifu University, Gifu (Japan). Faculty of Engineering

    1998-03-25

    Studies were carried out to develop a high-performance ceramic heat exchanger for ultra high temperatures using a fluidized bed. In the former study, Heat transfer coefficient had been improved by applying fluidized bed to the heat exchanger for high temperature with smooth ceramic tubes. In this study, finned ceramic tubes were applied instead of smooth tubes for more improvement of heat transfer and experiments were performed on condition that the maximum bed temperature was 1100degC. Fluidization remained stable and the bed temperature uniform in the bed similarly as the case of smooth tube. A heat transfer coefficient of finned tube was evaluated and it was improved about 3 times as large as that of smooth tube. The performance of the heat exchanger was also evaluated using temperature efficiency and exergy efficiency. 4 refs., 11 figs., 1 tab.

  12. Research and development of the industrial basic technologies of the next generation, 'composite materials (highly functional, crystal-controlled alloys)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'koseino kessho seigyo gokin'. Zenki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The results of the first phase research and development project for developing highly functional, crystal-controlled alloys as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop alloys superhighly resistant to heat, heat-resistant/high-rigidity and light/high-rigidity by controlling their crystals. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at designs of a total of 12 types of single-crystal alloys by the computer-aided alloy designing techniques, production of these alloys on a trial basis, and evaluation of their characteristics, for the alloys superhighly resistant to heat. Two of them are confirmed to be superior to the others, and selected as the alloys to be developed. This project has also established the single-crystal casting techniques, which allow crystal orientation almost completely. Various types of heat-resistant/high-rigidity and light/high-rigidity alloys are designed, produced on a trial basis, and evaluated for their characteristics. As a result, one alloy type is selected for each category. The other techniques developed by this project include those for adjusting powders for light/high-rigidity alloys whose average grain sizes are controlled and impurity contents are reduced. Bright prospects have been obtained for the techniques for superplastically forging the disk shapes. These efforts have almost achieved the development objectives of the first-phase R and D project. (NEDO)

  13. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloys'. Evaluation on final research and development (first report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    The present research work has been performing research and development of the following alloys: (1) 'single crystalline alloy' , the entire alloy being composed of one crystal eliminating crystalline boundaries as an ultra heat resistant alloy with emphasis placed on improvement in particularly the creep properties, and 'particle dispersion strengthened alloy', in which ultrafine particles of oxides are dispersed uniformly; and (2) 'ultra heat resistant and tough alloy' targeted at high-temperature toughness by using Ni-group allowing ultra plasticity forging processing by micronizing crystal particles, as an ultra plastic and highly tough alloy having better processibility than conventional alloys, and 'light-weight highly tough alloy' aimed at achieving light weight and high toughness by using Ti-group. Achievements derived from the present research and development may be summarized as follows: in alloy development, alloys having performance of the world's highest level or equivalent have been developed; a manufacturing technology to make products with complex shapes has been established by using the alloy material manufacturing technology and the alloy materials developed therefrom, where prototype components of such shapes as turbine blades and turbine disks for jet engines were fabricated successfully; and the big fruit obtained was that a large number of technological experiences were acquired from this research and development. (NEDO)

  14. Research and development of the industrial basic technologies of the next generation, 'composite materials (highly functional, crystal-controlled alloys)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'koseino kessho seigyo gokin'. Zenki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The results of the first phase research and development project for developing highly functional, crystal-controlled alloys as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop alloys superhighly resistant to heat, heat-resistant/high-rigidity and light/high-rigidity by controlling their crystals. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at designs of a total of 12 types of single-crystal alloys by the computer-aided alloy designing techniques, production of these alloys on a trial basis, and evaluation of their characteristics, for the alloys superhighly resistant to heat. Two of them are confirmed to be superior to the others, and selected as the alloys to be developed. This project has also established the single-crystal casting techniques, which allow crystal orientation almost completely. Various types of heat-resistant/high-rigidity and light/high-rigidity alloys are designed, produced on a trial basis, and evaluated for their characteristics. As a result, one alloy type is selected for each category. The other techniques developed by this project include those for adjusting powders for light/high-rigidity alloys whose average grain sizes are controlled and impurity contents are reduced. Bright prospects have been obtained for the techniques for superplastically forging the disk shapes. These efforts have almost achieved the development objectives of the first-phase R and D project. (NEDO)

  15. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloy'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    A proposal was given on a new processing process to use Ni-group super alloy, and elucidation was given on super plasticity phenomenon by using non-destructive tests. The Ni-group super heat-resistant alloy Mod. IN-100 subjected to different preforms by means of extrusion was given a super plasticity test at 1,050 degrees C to derive total elongation and 'm' value. As a result, it was disclosed that a material annealed for one hour at 1,070 degrees C after extrusion of 70% at 1,100 degrees C possesses the maximum 'm' value in the vicinity of 2.0 times 10{sup -2}s{sup -1}. The largest key to the new processing method is to improve the nature of the material, in which the plasticity manifestation velocity is accelerated by ten times to the order of 10{sup -2}s{sup -1} as described above. In addition, forging of IN-100 was made possible by using the ordinary forging equipment with the use of two-fold measures. The measures consist of maintaining temperature of IN-100 during casting by heating the die material to about 600 degrees C, rather than keeping it at a constant temperature, and then packing IN-100 in S35C steel material to accommodate the temperature decrease during casting inside the S35C pack. Thus, a processing method was made practical, eliminating need of the forging process to compress and solidify powder itself, that is the extrusion process. (NEDO)

  16. FY 1998 results of the regional consortium R and D project/the venture promotion type regional consortium R and D (small-/medium-size venture creation type). 2nd year. R and D of making a high-performance error correction technology in the digital information system semiconductive; 1998 nendo digital johokei ni okeru koseino ayamari teisei gijutsu no handotaika ni kansuru kenkyu kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper proposed a high-performance error correction method for restoring the lack and errors of digital data to the original state. In FY 1998, the algorithm of coding/decoding was mounted on personal computers. The program was verified in which the code length and dimensional number as parameters were made changed, and the program structure with variable parameters was acquired. Moreover, forms of connection /communication protocol with external equipment were designed which are needed in case of making it semiconductive. In FY 1999, the best decoding method in the algorithm study was selected, and the error correcting ability was improved. In making the algorithm semiconductive, using the design in which the parallel processing was paid attention to in the development of mounting using EPGA, circuits of high speed coding/decoding were established. The development of semiconductors for coding/decoding which work at 10 MHz was made possible. In the development of mounting using ASIC, the portion of interface of circuits which were able to work stably by FPGA was reinforced/improved. As a result, a processing speed of 50 Mbps which is about five times as fast as the FPGA processing was realized. (NEDO)

  17. Report on results of development of fuel cell power generation technology 1998. Research and development on polymer electrolyte fuel cell (technological development of element, research on ion exchange membrane for practicability of high performance cell); 1998 nendo seika hokokusho. Nenryo denchi hatsuden gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, yoso kenkyu kaihatsu (koseino denchi jitsuyoka no tame no ion kokan maku ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper explains the results during fiscal 1998 of ion exchange membranes in the development of polymer electrolyte fuel cells. Studies were made on three kinds of standard and two kinds of experimental membranes selected among the Flemion membranes, which are perfluorosulfonic acid membranes made by Asahi Glass Co.,Ltd., and also on the Nafion membranes by Dupon as reference. As the resistance evaluation of the environmental cycle for the membranes, a temperature cycle test was carried out, with the characteristics measured such as moisture content, membrane resistance, mechanical properties, and gas permeability, so that the effects were examined of the temperature cycle on the membranes. Evaluation was also commenced on the water permeability, an important substance-moving characteristic of ion exchange membranes. In the evaluation of the characteristics of membrane-electrode assemblies, the environmental cycle test was performed by joining electrodes to membranes, with the evaluation similarly made as for the membranes alone. On the basis of a correlation between the water permeability and the cell performance, studies were made on the effect of thickness of the membranes on the cell performances. A continuous stability/durability operation of 3,500 hours was verified using Flemion R. As for membrane reinforcement, studies were continued on the cloth and fibril reinforcements as in the previous year.(NEDO)

  18. FY 1998 survey report. Feasibility study of the new energy introduction/spread policy application (Study of the model project conception using natural energy utilization technology); 1998 nendo chosa hokokusho. Shin energy donyu fukyu hosaku tekiyo kanosei chosa (shizen energy riyo gijutsu wo katsuyoshita model jigyo koso no kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey clarified the problems about that consumers and various kinds of group do not come to tackle independently and positively the use of natural energy and the solutions, and studied the necessity of the model project to enlighten the society on those concretely and widely. The model project conception is to spread/settle various kinds of natural energy by making them linked with the regional economic growth and resource/environment problems in a community with a regional autonomous body as a unit. There, new incentives to be made toward the promotion/spread of natural energy are presented such as the construction of an energy self-supporting society which is closed-cycle by using various kinds of energy combinedly and compositely, the formation of ideas for adding values except kWh value to electric power generated by natural energy, etc. Besides, about the conception of model project, the training facility function and demonstration exhibition function for the purpose of education/enlightenment are also added in consideration of the importance of natural energy that general citizens should feel close to themselves. (NEDO)

  19. Report on feasibility study for introduction of biomass energy in Town of Kuzumaki. Town of milk, wine and clean energy, located at N.L. 40 degrees; Kuzumakicho biomass energy donyu kanosei chosa hokokusho. Hokui 40 do, milk to wine to clean energy no machi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    The feasibility study is conducted specifically for construction of a biomass plant in drawing the new energy visions for Town of Kuzumaki, Iwate Pref. The town is raising domestic animals, approximately 10,700 dairy cattle, 900 beef cattle, 2,800 hogs, and 18,000 chickens, actively producing the products, including approximately 40,000 tons/y of milk. On the other hand, these animals are discharging the excreta totaling around 500 tons/d, and adequate disposal and most effective utilization of the excreta as the resources provide the challenges to overcome. The project for constructing a demonstration model investigates treatment of the excreta discharged from 200 dairy cattle by an anaerobic fermentation plant, which uses the excreta and other organic wastes as the stock materials, and utilization of the biogas energy produced by the plant. The project is also considering to demonstrate the cycles of utilization of the digested sludge discharged from the fermentation process as the organic liquid compost. The economic evaluation results indicate that the plant gains a total income of 8.715 million/yen at a total expense of 8.575 million yen/y. (NEDO)

  20. FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

  1. Survey report for fiscal 1998. Surveys on possibility of introducing element technologies and future technological trends in the ECO and ENERGY city projects; 1998 nendo chosa hokokusho. Ekoene toshi project ni okeru yoso gijutsu donyu kanosei to kongo no gijutsu doko ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Covering ECO and ENERGY projects currently on the way under the New Sunshine Project, discussions were given on the possibility of utilizing the technological achievements, and the technological problems therein, from the energy supply and utilization aspects. Taken up as the basic concept of the ECO and ENERGY projects is 'optimization and implementation of a cascade-type energy system in cities under environmental restrictions'. Targets were placed on optimization of a total system including the demand side (a topping system), optimization of a total system including secondary energy other than heat (electric power and gas for example), optimization of energy efficiency for the system as a whole, and minimization of environmental load. The ECO and ENERGY technologies that are assumed for the future application were classified into the following six fields: the optimal energy supply system development field, heat storing technology field, thermoelectric power generation field, environment friendly heat pump system technology field, waste heat utilizing heat cycle technology field, and LNG cold heat utilizing technology field. (NEDO)

  2. FY 1998 annual report on the research on the possibility of introducing a usable chemical substance manufacturing system by utilizing natural gas containing CO2; CO{sub 2} gan'yu tennen gas den katsuyo ni yoru yuyo kagaku busshitsu seizo system donyu kanosei ni kansuru chosa kenkyu 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The trends of effective use of gas containing CO2 from natural gas fields are surveyed, and usable chemical substance manufacturing systems which utilize natural energy are investigated, evaluated and analyzed, to extract promising systems for effective use of CO2-containing natural gas and thereby to promote its effective use. Chapter 1 outlines possibility of integrated use of gas containing CO2 from natural gas fields and natural gas energy. Chapter 2 describes the research trends in the CO2 conversion reactions for using unexploited CO2 as the carbon source. Chapter 3 describes natural energy utilization technology applicable to gas containing CO2 from natural gas fields. Chapter 4 describes performance of chemical manufacturing systems utilizing natural gas containing CO2. The energy balances and CO2 emission coefficients are estimated, based on the above. The evaluation is implemented in the order of (1) conventional steam reforming, (2) steam reforming in which heat is supplied by a solar furnace, (3) examination of the exhaust gases from a methanol synthesis process, and (4) examination of CO2-mixed reforming. Chapter 5 describes summary and proposals. (NEDO)

  3. Report on achievements in proliferation project to assist introduction of environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998 (utilization facilities); Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo seika hokokusho. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo (riyo setsubi)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This paper describes the achievements of the discussions in fiscal 1998 on the utilization facilities related to the coal bed methane gas supply plan for the city of Tieling in China. The gas quality standard calls for 3,500 kcal/m{sup 3} or more (methane concentration of 41% or higher). The supply is planned to start in December 1999, and continue the supply of 141,000 Nm{sup 3}/day in 2000, and 212,000 Nm{sup 3}/day in 2001 and thereafter. A gas supply center to collect gases recovered from each mine will be installed in the vicinity of the existing gas holder located about 2 km east of the Tiefa Mining Bureau. The Japanese side bears the cost of installing a gas compression and transportation facility for gas supply to the city of Tieling, a monitoring system, and devices for comprehensive surveillance system. This paper shows the overall plan drawings, the drain separator room building plan, the plans for arranging devices in the machine room, and the piping scheme. In addition, the piping plan around the gas holder, and the basic device plan are shown. Also appearing in the paper are the machine summary drawings, summarized flow charts, gas holder plan, de-humidifier plan, and electricity and instrumentation plans. The main body and supporting structure for the gas holder, and the foundation strength calculation sheets are also shown. Descriptions are given also on the facilities to deal with variation in demand quantity and supply quantity. (NEDO)

  4. FY 1999 survey report on the research survey on the formation of a social consensus on the introduction of the global warming mitigation technology; 1999 nendo ondanka taisaku gijutsu no donyu ni kakawaru shakaiteki goi keisei ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As to the development and introduction of the global warming mitigation technology, the paper studied an approach to the formation of a social consensus and how to apply concrete methods and proposed a realistic approach in the light of the present situation of public enterprises in Japan. As tools and rules which are particularly important in activities of forming the consensus, the paper cited up what the PR control should be, responses to mass communications, HP making and regulation/preparation of the related laws, and made a concrete study. As examples in which there occurred friction with the society due to the insufficient formation of consensus, the following construction plans were taken up to consider problems, etc. in disclosure of the information in the plans: Underground Research Laboratory, movable weir in the Yoshino River, and waste disposal facilities at Fuimae tideland. Also in Japan, some methods for the consensus formation have been carried out, and in the survey, as concepts for classifying the methods, two different approaches, Public Outreach and Public Relations, were introduced. As to the former, a consensus formation method in the construction of power plants in Japan was introduced, and as to the latter, a method in consensus conferences in the U.K. (NEDO)

  5. Research report for fiscal 1998 on development of environmentally friendly high-efficiency energy utilization system. Research of optimum system designing technology (Research of effect of eco-energy city system technology introduction to Osaka); Kankyo chowagata kokoritsu energy riyo system kaihatsu Saiteki system sekkei gijutsu no kenkyu 1998 nendo chosa hokokusho (Osakafu). Ekoene toshi system gijutsu donyu koka no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Concerning the district in Osaka Prefecture selected for study in fiscal 1997, it is investigated whether energy efficiency is enhanced, and environmental impact reduced, by the introduction of element technologies, and the findings are compared with the results expected to be produced without their introduction. Problems about their introduction are also discussed. Taken up for study are the collection and utilization of heat from a water granulated slag manufacturing plant of an iron mill, exhaust heat reform and recovery system at a chemical plant, heat supply system driven by a high-performance heat pump capable of dealing with various kinds of fuels, compression/suction hybrid heat utilization system, and a cold heat supply system using microspheres. Annual energy consumption, CO2 and NOx emissions, and costs are calculated for each of them. Concerning these element technologies, various tasks are discussed, related to the technology of their systematization, economy, dissemination of district heat supply, and wide-area heat supply businesses utilizing exhaust heat. As the result, it is concluded that the primary energy consumption as a whole is reduced upon their introduction and that energy saving effect and environmental impact reducing effect are in presence. (NEDO)

  6. Report on investigations in fiscal 2000 on the projects to support introduction of environment friendly coal utilization system. Green helmet project for briquette production plant - Mae Moh coal mine, Thailand; 2000 nendo kankyo chowagata sekitan riyo system donyu shien jigyo chosa hokokusho. Briquette seizo setsubi ni kakawaru green helmet jigyo (Thai koku Mae Moh tanko)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    This Green Helmet Project is intended to suppress generation of environment polluting substances in association with coal utilization in Thailand by demonstrating and improving the proliferation infrastructure for the clean coal technology to be used widely in Thailand. The project is also intended to serve for stabilized assurance of energies for Japan. The demonstration project related to briquette manufacturing facilities executed as one of the 'Projects to support introduction of environment friendly coal utilization system' is intended to manufacture at low cost a briquette which is low in odor, free of smoke, and suppressed largely of sulfur oxide generation. The briquette is made by adding clayish minerals, sulfur, a fixing agent and a binder into brown coal being a low grade coal. The project implements proliferation of the technology to reduce environmental load associated with coal utilization in developing countries according to the situation and needs of the counterpart countries. The present project has performed the site surveys and guidance of operation and maintenance techniques as follow-up works of the demonstration project having been completed by cooperation between Japan and Thailand. It is considered that what had been intended in the beginning has been achieved sufficiently. (NEDO)

  7. Research report of fiscal 1997. Feasibility research on introduction of distributed power sources using new energy (photovoltaic and wind power generation) in the South Pacific; 1997 nendo chosa hokokusho. Minami Taiheiyo ni okeru shin energy (taiyoko, furyoku nado) wo katsuyoshita bunsangata dengen no donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Feasibility research was made on distributed power sources using photovoltaic and wind power generation in Tonga and Samoa. For the best mix of environment-friendly power sources, hearing from government leaders and power business persons, and field inspection were carried out. Foreign currency earnings of Tonga are dependent on remittance from nations working overseas, while since diesel fuel for power generation is expensive because of import through Fiji and tariffs, multi-power sources for power cost reduction and low-cost new power systems are in expectation. Underground transmission and distribution lines are under consideration to prevent typhoon damages. Both countries are probably rich in wind power potential, however, wind condition data are poor requiring further researches. Tonga government is in charge of power business except that in Tongatapu island. In Samoa, EPC (Electric Power Corp.) is in charge of power business. Hydroelectric power generation is possible because of rivers formed by abundant tropical rains. Feasibility research was made on coal-firing, fuel cell combined, wind power, photovoltaic and waste power generation. 7 figs.

  8. Achievement report for fiscal 1997 (New Sunshine Project) on the development of superconductor power application technology. Research on a total system / investigative research on introduction effects; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu (New Sunshine keikaku) seika hokokusho. Total system nado no kenkyu / donyu koka no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes investigation and discussion on effects of introducing a superconductor power application technology. The generator sub-committee has compared features, technical problems and development expenses in the first and second proposals, but has not reached the final conclusion. The first proposal is targeted for early realization of 200-300 MW class generators with development cost of six to seven billion yen and a development term of seven years. These developments raise largely towards practical application the levels of material technologies, fabrication and processing technologies, and analysis and design technologies. The second proposal is intended of developing 200-300 MW class generators targeted for increased diameter, as a reduced size machine of a 600-MW generator being a future generator. It will take development cost of eight to nine billion yen with the period of nine years for the development. Majority of the technologies required for developing the future 600-MW class generator can be demonstrated. The AC superconductor device sub-committee has investigated design examples, clarified the specification requirements, and investigated and studied the development measures. The oxide superconductor sub-committee has investigated and studied making wires and conductors, and device application feasibility, but has not reached the stage of presenting specific research and development methods. The practical application strategy sub-committee has also not been able to present a collective measure because of difficulty of making future prospect on the electric power business. (NEDO)

  9. Project to support promotion of forming an environmentally friendly energy community. Survey report on 'a survey on introduction of an RDF electric power generation system utilizing general wastes in the Noto area'; Kankyo chowagata energy community keisei sokushin hojo jigyo. 'Noto chiiki ni okeru ippan haikibutsu riyo RDF hatsuden no donyu ni kansuru chosa' chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A business feasibility survey was performed on introduction of an RDF electric power generation system utilizing general wastes in the Noto area. Wastes quantity was estimated by accounting for large-sized wastes to be generated newly as a result of enforcement of the container package recycling law, and transfer of non-combustible wastes to incineration. The quantity was estimated to be 84,000 tons annually. Quantities of RDF and heat were calculated from this estimation to be 103 tons per day and 400 lkcal/kg respectively. According to the result of discussing the RDF transportation systems, time-based freight was found advantageous for short distance, and distance freight system for long distance in terms of cost. Discussions for RDF power systems were carried out on an RDF circulation fluid bed furnace plus ash melting furnace, a fluid bed gasification melting furnace, and shaft furnace type gasification melting furnace. In a comprehensive view, it is difficult to distinguish them in terms of merit and demerit. Molten slag was assumed to be re-utilized, but cost for the re-utilization should be considered. According to the result of discussing the business feasibility, it was found difficult to make it profitable by operating the RDF power generation business alone, and wastes incineration charge should be collected. (NEDO)

  10. Study of reciprocating engine with Z mechanism. Part 1. Discussion of effect on the performances of new concept engine; Yodo shiten riron wo mochiita ofuku do engine ni kansuru kenkyu. 1. Shinkihon kozo no donyu ni yoru seino kojo no suisatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshizawa, Y; Fukuzaki, S; Kanno, M [Yoshiki Industrial Co. Ltd., Yamagata (Japan)

    1997-10-01

    A new reciprocating engine was developed as an application of new mechanism named as `Z mechanism.` In this new engine, the piston motion is described by a simple sine function and gives lower velocity around top dead center than that in conventional piston engines. Thus, the mode of combustion in this engine is closer to constant-volume process and gives higher thermal efficiency than ordinary engines. Use of Z-mechanism also eliminated high-order components of vibration that ordinary engines suffer. Development high-performance engine was successfully conducted with this new mechanism. 4 refs., 11 figs., 1 tab.

  11. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education - iron and steel (Survey on education accreditation in material field); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (tekko) -Zairyo bunya ni okeru kyoiku nintei ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, a survey was performed on external accreditation systems for engineer education such as in universities and other organizations in the material field. In the survey, discussions were given on whether or not the education program accreditation system for the material field being structured has any problem in the actual operation of the accreditation through trials at Chiba Engineering University and Tokai University. As a result, it was revealed that the criteria are too general, requiring more detailed description on the guideline, and criteria should be so considered that assessment at higher levels can be given to the graduation research, which is a Japan's particular education system. In addition, it was made clear as a problem in the education programming side that a room for improvement remains in the education methods for the engineering ethics, communication skills, and the method for evaluating the students' achievements. In the survey on the methods for examination and accreditation in the U.S.A. it was found out that education organizations are perplexed with the new criteria of EC 2000. (NEDO)

  12. FY 2000 report on the survey for introduction of the hot spring effect prediction method in the geothermal development promotion survey. Improvement of the hot spring effect prediction method in the geothermal development promotion survey; 2000 nendo chinetsu kaihatsu sokushin chosa. Onsen eikyo yosoku shuho donyu chosa - Chinetsu kaihatsu sokushin chosa ni okeru onsen eikyo yosoku shuho no kairyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Supposing the case where the geothermal development promotion survey was carried out in promising geothermal areas in Japan, investigational study was conducted on possibilities of introducing the hot spring effect prediction method, improvement of the method, etc. In the survey, adjustment/classification of formation mechanisms of hot spring were made. For each of the formation mechanisms, the mechanisms in case of the geothermal development having effects were studied/summarized. As to how effects are brought about, presumed were the lowering of water level and decrease in discharge amount in accordance with the decreasing pressure and the dilution by increase in mixture of the ground water around the area. Also cited were the vaporization of hot spring aquifers by the increasing rate of vapor inflow, etc. For the introduction of the hot spring effect prediction method to the geothermal development promotion survey, the problem is short supply of various data, and the examination for it was made. Based on the results of the survey, items to be studied in case of introducing the hot spring effect prediction method were selected. Further, the hot spring effect prediction flow in case of introducing surface survey and well survey was made out. (NEDO)

  13. Fiscal 2000 project on measures for assisting and diffusing environmentally-friendly coal utilization system introduction. CMG recovery/utilization system joint demonstration project; 2000 nendo kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo chosa hokoku. CMG kaishu riyo system kyodo jissho jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A CMG (coal mine gas) recovery/utilization system was designed, constructed, and then demonstrated at a model coal mining district in Liaoning Province for the purpose of contributing to the solution of energy and environment related problems in China. The recovery system demonstration test, aiming to improve on safety and productivity of coal mining and to supply recovered gas with stability, involved gas drainage test boring, mine sealing, sealed gas induction control, centralized gas monitoring, etc., which were carried out at the coal mine working face. A utilization system demonstration test was conducted, and CMG would continue to be supplied to the current users and CMG utilization would be started at the other 6 coal mines. For the supply of CMG to large-scale gas consuming areas, steel materials were manufactured and processed for spherical gas holders and denitrification facilities, gas holders were constructed, pipe lines were installed, and a provisional gas supply was carried out. For the transfer and diffusion of the technology, Chinese engineers were trained in Japan and Japanese engineers were dispatched to China. (NEDO)

  14. Survey report for fiscal 1998. Surveys on possibility of introducing element technologies and future technological trends in the ECO and ENERGY city projects; 1998 nendo chosa hokokusho. Ekoene toshi project ni okeru yoso gijutsu donyu kanosei to kongo no gijutsu doko ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Covering ECO and ENERGY projects currently on the way under the New Sunshine Project, discussions were given on the possibility of utilizing the technological achievements, and the technological problems therein, from the energy supply and utilization aspects. Taken up as the basic concept of the ECO and ENERGY projects is 'optimization and implementation of a cascade-type energy system in cities under environmental restrictions'. Targets were placed on optimization of a total system including the demand side (a topping system), optimization of a total system including secondary energy other than heat (electric power and gas for example), optimization of energy efficiency for the system as a whole, and minimization of environmental load. The ECO and ENERGY technologies that are assumed for the future application were classified into the following six fields: the optimal energy supply system development field, heat storing technology field, thermoelectric power generation field, environment friendly heat pump system technology field, waste heat utilizing heat cycle technology field, and LNG cold heat utilizing technology field. (NEDO)

  15. FY 1999 report on the survey of the reinforcement of the base for introduction/spread/improvement of clean energy vehicles in the Kinki region, Japan; 1999 nendo chosa hokokusho. Kinki chiiki clean energy jidosha donyu fukyu sokushin kiban kyoka chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Survey was made with the aim of studying measures to be taken for introduction/promotion of clean energy vehicles (CEV) in the Kinki region and of making a guidebook which included 8 CEV introduction menus based on the characteristics/needs in the Kinki region. In the survey of the state of CEV introduction in the Kinki region, a total number of the CEVs introduced in the region was estimated at approximately 5,300 (19.1% of the whole country), which indicated that the CEV introduction was increasing in comparison with the rate of the general vehicles registered (14.6% of the whole country). On the other hand, the fuel supply stations prepared such as eco-station are limited mostly to Osaka prefecture, which showed that the base is still unprepared. From the questionnaire survey made for 367 autonomous bodies and main 73 companies, problems and the needs for the wide area/large quantity spread were grasped, and various basic data were obtained. To solve problems, the setting-up of the Kinki CEV introduction/spread/promotion committee (CEV Kansai) was studied. (NEDO)

  16. FY 1999 report on the results of the fundamental investigation for promotion of Joint Implementation. Preliminary evaluation of introduction of VICS systems in Klang Valley and Multimedia Super Corridor in Malaysia; 1999 nendo Malaysia koku Klang Valley oyobi multimedia super corridor ni okeru VICS system donyu no jizen hyoka chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Feasibility study is conducted for introduction of the VICSs (Vehicle Information and Communication Systems) in Malaysia's Klang Valley and Multimedia Super Corridor, to contribute to abatement of the greenhouse effect gases and saving energy. This study has produced the following results. The systems need a total fund of about 1.4 billion yen, including the design fees, when based on the FM multiplex broadcasting, and annual operation/maintenance cost of about 110,000 million yen. These systems are expected to save 4,850 toe/y of fuel and abate CO2 emissions by 11,200 t/y, with the benefit cost ratios of 20.2 toe/million yen and 46.6 tons of CO2/million yen, respectively, when they are in service for 10 years. Introduction of the VICS system in Malaysia is highly feasible both technically and economically, which, however, will need establishment of, e.g., the JICA-proposed integrated traffic information system and Malaysia Traffic Information Authority. (NEDO)

  17. 'Development and introduction of ice water conveyance system and verification of low temperature blast system' for leveling off electric power load; Denryoku fuka heijunka wo misueta 'hyosui hanso hoshiki no kaihatsu donyu to teion sofu hoshiki no kensho'

    Energy Technology Data Exchange (ETDEWEB)

    Kuriyama, T. [Nikken Sekkei Ltd., Osaka (Japan)

    1999-11-05

    From the view point of the earth environment protection, energy-saving in the field of building air-conditioning has become increasingly important. On the other hand, the utilization of nighttime electric power is needed to ease the electric power supply and demand problem, and in this connection, a wider introduction of the ice heat storage system is recommended as one of the means to cope with such a problem. However, the ice heat storage system also has problems to be solved such as energy savability, and economy. Under such circumstances, various technical research and development efforts as well as evaluation thereof have been made centering around the 'technical development of the ice water conveyance system' and the 'evaluation of the low temperature blast system' for energy-saving, facility cost reduction and electric power load leveling off, and as a matter of fact these systems have been installed in actual buildings with useful results. (author)

  18. FY 1999 report on the results of the fundamental investigation for promotion of Joint Implementation. Preliminary evaluation of introduction of VICS systems in Klang Valley and Multimedia Super Corridor in Malaysia; 1999 nendo Malaysia koku Klang Valley oyobi multimedia super corridor ni okeru VICS system donyu no jizen hyoka chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Feasibility study is conducted for introduction of the VICSs (Vehicle Information and Communication Systems) in Malaysia's Klang Valley and Multimedia Super Corridor, to contribute to abatement of the greenhouse effect gases and saving energy. This study has produced the following results. The systems need a total fund of about 1.4 billion yen, including the design fees, when based on the FM multiplex broadcasting, and annual operation/maintenance cost of about 110,000 million yen. These systems are expected to save 4,850 toe/y of fuel and abate CO2 emissions by 11,200 t/y, with the benefit cost ratios of 20.2 toe/million yen and 46.6 tons of CO2/million yen, respectively, when they are in service for 10 years. Introduction of the VICS system in Malaysia is highly feasible both technically and economically, which, however, will need establishment of, e.g., the JICA-proposed integrated traffic information system and Malaysia Traffic Information Authority. (NEDO)

  19. Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project on simplified desulfurizers; 1997 nendo seika hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (kan`i datsuryu setsubi ni kakawaru jissho jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To reduce SOx with coal utilization, a desulfurizer is introduced in Thailand as diffusion activities in the demonstration program. The purpose is to reduce the environmental pollutants. For this desulfurizer, lime mud mainly composed of lime stone is used as an absorber. SO2 in the flue gas is absorbed by the slurry of lime mud, to form calcium sulfite. The calcium sulfite blown in the bottom of recycling tank is oxidized by oxygen in the air, to form gypsum. The gypsum is recovered as a by-product. In this fiscal year, a feeder of lime stone, spray nozzles, and various analysis apparatuses were supplied. Supervisors for electric instrumentation/control were also dispatched as well as for main body construction, to carry out the instrumentation setting works, check of sequences, and adjustment of apparatuses. After the test operation, supervisors for the demonstration operation were dispatched up to March 1998, to conduct the cooperation works between Japan and Thailand sides. Thus, successful and successive demonstration operation was confirmed. 21 figs., 6 tabs.

  20. Introduction of new energies that gives vitality to town of Mano, industries, and people. Report on establishment of new energy vision in Mano Town area (Niigata Prefecture); Mano no machi, sangyo, hito ni katsuryoku wo ataeru shin energy no donyu. Manocho chiiki shin energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Based on assurance of energy availability in Sado Island, and age advancing of the population, an energy vision was established with the target of building 'Mano Town that seem real to everyone to find it good to live therein'. The population of Mano Town is about 6000 persons, and the energy consumption in total is 22,350 kl/year as converted into petroleum (industries and public sector at 12,162, households at 2,720, and transportation at 7,433). The new energy introduction is divided into three steps of the initial stage, middle stage, and long term stage. The initial stage will execute introduction of photovoltaic power generation into primary schools, promotion of utilization of solar energy at homes, promotion of introducing firewood and chaff boilers, and introduction of cogeneration into Yutoripia Mano. For the middle stage, discussions were given on introduction of photovoltaic power generation into the city office building, manufacture of light oil substituting fuel through rape seed and soy bean cultivation, introduction of hybrid automobiles, and manufacture of pellet fuel by utilizing wood wastes. For the long term stage, discussions were given on wind power generation, and ethanol fuel manufacture. (NEDO)

  1. Report on the fiscal 1993 investigational study of the environmental technology development trend in Japan. Trend survey of the introduction policy of environmentally friendly products; 1993 nendo Nippon ni okeru kankyo gijutsu kaihatsu doko nado ni kansuru chosa kenkyu hokokusho. Kankyo chowagata seihin no donyu hosaku nado doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    An investigation was conducted into the systematical scheme for the introduction and promotion of environmentally friendly products mostly to the U.S., Europe and China. In the U.S., the introduction policy is given to one and all fields of the industry. The introduction policy of the U.S. has a characteristic that the introduction is left to the market principle by DSM or permit dealing, etc. except the preferential tax system and systematical finance in which the government is concerned. The policy of European countries is characterized by the idea preceding, standards or rules are first given, and the whole is pushed on to them. Accordingly, it seems that there is few atmosphere of expecting to receive the government side economic incentives from the corporate side. Legal regulations on the environment in China were prepared in a comparatively early time (1979), but the supervision of obeying the regulations and the appearance/spread of environmentally friendly product menus have just started. Accordingly, as the introduction policy on environmentally friendly products, there was found nothing valuable but the regulations. 12 refs., 3 figs., 15 tabs.

  2. Fiscal 1999 report on basic research for promotion of joint implementation programs. Research on introduction of dual mode bus system for greenhouse gas reduction; 1999 nendo onshitsu koka gas sakugen no tame no dual mode bus system donyu ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A feasibility study is conducted of the above-named system in Malaysia, to be linked to COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) clean development mechanism (CDM). The dual mode bus system (DMBS) is a combination of advantages of the rail running stock such as monorails and the road running stock in that the buses when running on dedicated roads are automatedly formed into a linear formation and travel at a specified economical speed. When running on ordinary roads, the formation is broken into individual buses, and they spread in the town where they travel in a planar pattern. The economical speed and reduction in air drag thanks to the linear formation saves fuel and reduces CO2 emissions. The complementary relationship to be formed with the existing public transportation systems will also function positively. Studies are conducted on condition that two routes be laid in the Kuala Lumpur urban area and one in the new city Putra Jaya. All the three routes exhibit a high economic internal rate of return, but their financial internal rate of return indicates that probabilities are low that they will pay as private businesses. They will need financial supports such as subsidies. Contribution to CO2 reduction may be slight when attention is paid only to the partial changeover from the existing bus system to DMBS but larger contribution will be found in crossover from private cars to DMBS which is higher in quality of service. (NEDO)

  3. Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project of circulating fluidized bed boiler (Jinzhou Coal-Thermal Power Corporation); 1997 nendo seika hokokusho (kankyo chowagata sekitan riyo system donyu shien jigyo). Junkan ryudosho boiler ni kakawaru jissho jigyo (Jinzhou netsuden sokoji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To verify the clean coal technology to be diffused in China and consolidate its diffusion basis, demonstration project of circulating fluidized bed boiler was conducted through the cooperation with China which is positive in its introduction. This report describes its characteristics. Coal and limestone are supplied in a lower part of combustion chamber, and are mixed with circulating ash by fluidized air for combustion. Densely fluidized bed the same as the bubbling fluidized bed is formed in the lower part of combustion chamber, which provides excellent stability in ignition and combustion. Particles including ash, char and limestone formed during the combustion are discharged into the cyclone through the convection heat transfer part at the outlet of combustion chamber with the combustion gas flow. Since the gas temperature is lowered to 400 to 500degC at the convection heat transfer part, troubles of the ash circulating system can be prevented. The combustion gas separated from ash at the cyclone is discharged through the heat exchanger and precipitator, and the collected ash is returned to the lower part of combustion chamber. In FY 1997, design, fabrication, procurement/inspection, field survey/meeting, survey of visitors/meeting, and education were carried out. 4 figs., 4 tabs.

  4. Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Follow-up project on circulating fluidized bed boiler introduction (Calaca Batangas Thermal Power Station); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (junkan ryudosho boiler ni kakawaru follow up jigyo (Calaca Batangas karyoku hatsudensho))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the follow-up project, to promote the diffusion of results of the clean coal technology (CCT) model projects, experts of circulating fluidized bed boilers were dispatched, to guide and advise for the operation of facilities introduced in these projects. The purpose of these projects is to diffuse the CCTs, and to support the promotion of environmental measures. Some guidance and advice about operation processes, data processing, operation regulation, maintenance, and boiler maintenance works were provided to the Ministry of Energy and Electric Power Corporation of the Philippines. Semirara, Malangas, and Samar coals in the Philippines were used for the tests. The boiler facilities could be operated by Philippine operators themselves. Based on the guidance and advice about operation processes, combustion tests using various Philippine coals were also planned and conducted by themselves. The maintenance techniques were transferred to Philippine operators through the inspection, repair and advice. The Philippine side understood the technologies well, and the circulating fluidized bed boiler technology was independently educated in the Philippines. 23 figs., 16 tabs.

  5. FY 1998 annual report on the research on the possibility of introducing a usable chemical substance manufacturing system by utilizing natural gas containing CO2; CO{sub 2} gan'yu tennen gas den katsuyo ni yoru yuyo kagaku busshitsu seizo system donyu kanosei ni kansuru chosa kenkyu 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The trends of effective use of gas containing CO2 from natural gas fields are surveyed, and usable chemical substance manufacturing systems which utilize natural energy are investigated, evaluated and analyzed, to extract promising systems for effective use of CO2-containing natural gas and thereby to promote its effective use. Chapter 1 outlines possibility of integrated use of gas containing CO2 from natural gas fields and natural gas energy. Chapter 2 describes the research trends in the CO2 conversion reactions for using unexploited CO2 as the carbon source. Chapter 3 describes natural energy utilization technology applicable to gas containing CO2 from natural gas fields. Chapter 4 describes performance of chemical manufacturing systems utilizing natural gas containing CO2. The energy balances and CO2 emission coefficients are estimated, based on the above. The evaluation is implemented in the order of (1) conventional steam reforming, (2) steam reforming in which heat is supplied by a solar furnace, (3) examination of the exhaust gases from a methanol synthesis process, and (4) examination of CO2-mixed reforming. Chapter 5 describes summary and proposals. (NEDO)

  6. FY 1999 report on the results of a feasibility study on a system for producing useful chemical substances by utilizing CO2-containing natural gas fields. II; 1999 nendo CO{sub 2} gan'yu tennen gas den katsuyo ni yoru yuyo kagaku busshitsu seizo system donyu kanosei ni kansuru chosa kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper studied the solar energy use methanol synthesis using CO2 as raw material in the natural gas field with which a large quantity of CO2 is associated. This is a report on the FY 1999 survey. It was found that comparatively many natural gas fields containing CO2 exist also in Asia/Oceania regions. It was also found that when considering the climate and the transportation to Japan, Australia has more advantages in terms of the effective desert area, etc. and is the best site for solar system construction. Various solar concentrating/collecting methods now under development are roughly viewed to extract characteristics and developmental conditions. As to the reforming reaction furnace, it is necessary not only to absorb the world technology, but to develop Japan's original one. The conceptual design and assessment of the system were conducted. About the associated CO2, a limit of the concentration for use was estimated at 25%. In the study of elements of system structure, examined was the thermally combined simulation of heat flow and chemical reaction in the solar heat reaction furnace, and simple models were calculated and subjects were extracted. In a comparison with the conventional methanol synthesis method, this system was found to be excellent in conservation of fossil fuel resources and reduction in CO2 emissions. (NEDO)

  7. FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

  8. Research report for fiscal 1998. Basic research for promoting joint implementation of energy use rationalization in Chinese steel industry (examination of introduction of scrap preheating system for electric furnaces); 1998 nendo chosa hokokusho. Chugoku tekkogyo ni okeru energy no shiyo gorika (denkiro scrap yonetsu system donyu kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Investigations are conducted on a project of introducing a scrap preheating system based on the central insertion movable shaft design into China's electric furnaces for the sake of energy saving and global warming gas reduction. Of the electric furnaces numbering approximately 3400 now in operation in China, most are small and antiquated, and are extremely low in energy efficiency when in operation. The percentage of electricity supplied by coal-fired facilities is high, and this causes the CO2 reduction problem. Investigations are conducted into four steel mills operating electric furnaces, and examinations are made on the applicability of a preheating system, which is the ultimate batch system developed by Nippon Steel Corporation. Studies are conducted for Wuyang Iron and Steel Co., Ltd., Tianjin Steel Pipe Co., Ltd., Budong Iron and Steel Co., Ltd., and Shanghai Five Steel Co., Ltd., and it is found that greenhouse gas will be reduced by 31,000 tons, 21,000 tons, 13,000 tons, and 11,000-tons at the said mills, respectively. It is learned that the cost to be invested will be retrieved in approximately 2.5 years, 2.8 years, 7.7 years, and 8.0 years, respectively. It is concluded that Shanghai Budong Iron and Steel (Group) Co., Ltd., is the best candidate to be equipped with the above-said system. (NEDO)

  9. Report on achievements in proliferation project to introduce environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998; Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This paper describes the discussion report for fiscal 1998 on the CMG (coal methane gas) recovery and utilization project to be implemented from fiscal 1998 through fiscal 2002 at Tiefa Mining Bureau of Liaoning Province in China. The Daixing mine was selected as the survey object. The introduced technologies and facilities include test drilling for degassing (medium measure horizontal degassing of 300-m class), induction from degassing holes, fly ash sealing, sealed gas degassing, surveillance and control technologies and facilities. The recovered gas is to be supplied to the cities of Tiefa and Tieling as town gas, for which compressed gas feeding and controlling technologies and facilities will be introduced. This paper lists the gush-out quantity (1,000 Nm{sup 3}), the recovery quantity (1,000 Nm{sup 3}), the recovered gas concentration (%), the utilization quantity (1,000 Nm{sup 3}), and the utilization rate (%). The figures for the respective items before and after the implementation are 128366, 32949, 44.5, 7000, 5, 123500, 43890, 49.1, 39826, and 32. The quantity of gas gushing out at facings decreases in association with increase in the recovered gas quantity, whereas the gas concentration at facings in the Daixing mine in 2003 is estimated to decrease to 0.1%, contributing to safe mining operation. The test drilling for medium measure horizontal degassing expands the degassing assured scope per one test drilling seat, and can reduce the total test drilling length and construction amount. (NEDO)

  10. Fiscal 2000 survey of refuse-fueled power generation introduction technology, etc. Survey of industrial refuse-fueled power generation (Industrial refuse-fueled power generation case study implementation - 1); 2000 nendo chosa haikibutsu hatsuden donyu gijutsu chosa to - Sangyo haikibutsu hatsuden chosa (Sangyo haikibutsu hatsuden case study no jisshi - 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Case studies were conducted of industrial refuse-fueled power generation using plastic waste, paper waste, and wood chips, and the same using the excretions of cattle. In the study of power generation fueled by mixed waste containing plastic waste, 325t/d, 220t/d, and 130t/d incinerators having the lower calorific value of 5,960-6,401 kcal/kg were taken up, and steam conditions, generator output, generating-end efficiency, station service power ratio, sending-end efficiency, etc., were tentatively calculated. As for cost efficiency, a manufacturer's estimate indicated that commercialization would be impossible in all the cases unless the construction cost was cut down. In the study of excretion-fueled power generation, cases were taken up where medium-temperature fermentation proceeded for the excretions of 620-29,853 dairy cows (32-1,576 t/d). A calculation was performed on conditions that the construction cost and maintenance/utility costs were as estimated by the manufacturer, that the excretion treatment and power generation facilities were covered by subsidies, and that personnel expenses of 6-million yen were necessary. It was then found that there would be commercial viability in case the yield was 790t/d or higher. (NEDO)

  11. Fiscal 2000 survey report. High-efficiency energy system introduction promotion project for houses and structures - Houses (Technical classification tables prepared by analysis of proposed systems, and comments on the same); 2000 nendo jutaku kenchikubutsu kokoritsu energy system donyu sokushin jigyo (jutaku ni kakawaru mono) teian system no bunseki ni yoru gijutsu bunruihyo oyobi dokaisetsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As an energy conservation promotion measure, a project is under development for introducing and subsidizing high-efficiency energy systems and for letting their effect known publicly and widely. The number of proposed energy systems has increased greatly and technical divisions to follow in classifying them have become vague, from which problems are now arising over the execution of follow-up checks and the maintenance of fair treatment. In the effort to solve this problem, 376 propositions are analyzed and classified, a technical classification method is proposed, and an instruction manual on the method is compiled. The classification involves (1) proposed classification, (2) variation, (3) energy reduction rate, and (4) tentatively calculated cost. Item (1) deals with the basic classification (air-conditioning, ventilation, and hot water supply, and, to be considered in combination with them, options which are cooking, illumination, and others) and, item (2) covers eight items such as new/old construction, structure, and structural frame. In Chapter 1 of the report, the 376 propositions are put in order according to common classification items and an original classification table is prepared. In Chapter 2, the goals are clarified and the classification principles are defined. In Chapter 3, the classification is checked for its validity and some realistic ways of grouping are described. In Chapter 4, a classification implementation flow chart is shown. (NEDO)

  12. Report on investigations in fiscal 2000 on the basic investigation on promotion of joint implementation. Introduction of central load dispatching center in Oman; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Oman koku ni okeru chuo kyuden shireijo no donyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In Oman, electric power supply is made by operating a large number of gas turbine generators. However, the operation is inefficient as a whole as a result of operating the generators provided with large reserves to minimize effects of unit failures in each power plant as one unit. Therefore, the present investigative study has begun from discussing the achievement of energy conservation and reduction of greenhouse gas emission by managing the demand and supply in an economical manner upon introducing a central load dispatching center (CLDC). Given the introduction of CLDC, the effects of introducing the equi-{lambda} method with still higher economy and of introducing the control system of reserve operation power may be summarized as follows: the energy saving effects (converted to crude oil quantity) are 22,400 toe/year for the former case and 35,800 toe/year for the latter case; and the greenhouse gas reduction effects are 52,000 t-CO2/year for the former case and 84,000 t-CO2/year for the latter case. This is an effective project with a considerable amount of effect as a result of introducing the equi-{lambda} and of introducing the control system of reserve operation power, while the investment amount is relatively small. The investment recovery period is 2.5 years and 2 years, respectively, making the project considerably promising as a CDM project. (NEDO)

  13. Report on achievements in proliferation project to assist introduction of environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998 (recovering facilities); Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo. 1998 nendo CMG kaishu riyo system kyodo system kyodo jissho jigyo (kaishu setsubi)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This paper describes the achievements of the discussions in fiscal 1998 on the recovering system for coal bed methane gas to be supplied to the city of Tieling in China. The paper puts on record the associated documents, and figures and drawings. The associated documents appearing in the paper include the table for explosion-proof examination on the recovering devices, a parts list for the RK-3A type test drilling machine, and its operation manual. Specifications for the test drilling machine (including those for the sealing pumps), specifications for the mouth facilities, and device lists are shown. Test drilling device arrangement drawings and standard drilling record table are also described. Central blower specifications, a back-fire preventing device, a device to prevent well exterior from freezing, and a summarized drawing for drain remover for gas induction for the Daixing mine are explained. The schemes for induction and sealing, specifications and procedures for observation devices are shown. Specifications for sealing materials and the centralized monitoring facilities are also touched on. The safety measures, measures taken for power failure in the centralized monitoring facilities, and the control organization are described. Test drilling cost simulation and environment assessing methods are also described. The figures and drawings presented include the topographic map, Daixing mine cavity drawing, pipeline network, and chart for representative test drilling columns near the coal beds were also presented. (NEDO)

  14. FY 1999 report on the results of the superconductive energy application technology development/research on a total system, etc. Survey of potentiality of the commercialization of superconductive technology, effects of the introduction, etc. (Future course of the superconductive technology development in Japan); 1999 nendo chodendo denryoku oryokuyo gijutsu kaihatsu total system nado no kenkyu. Chodendo gijutsu no jitsuyoka kanosei oyobi donyu koka nado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    By the use of superconductive technology, the following are aimed at: marked reduction in power loss of electrical equipment and power transmission path, and size/weight reduction in electrical devices by high current/magnetic flux density. The superconductive technology has advantages such as great energy saving effect, CO2 reduction and global environmental preservation. As an example, concerning the superconductive generator now being developed under the New Sunshine Project, power loss can be reduced by half, and by the use of high magnetic field, size/weight can be reduced such as reduction in rotor diameter and reduction in weight by half. Further, as an innovative system, cited are the superconducting magnetic energy storage system (SMES) and flywheel energy storage system. The superconducting magnetic levitation railway, medical use MRI, etc. have also innovativity which is difficult to get in the conventional technology. Effects are also expected of introducing the process development using superconducting magnet such as magnetic separation, electromagnetic metallurgy, electromagnetic agitation and monocrytal growth convection control. Also cited is Josephson electronic device. High performance SQUID in bio-magnetic/non-destructive inspection is also expected to be developed. (NEDO)

  15. FY 1999 report on the potential survey of the environmentally friendly type coal utilization system - Dispatch of engineers. A. Project for supporting the introduction of the environmentally friendly type coal utilization system (model project)/pre-survey for the potential survey; 1999 nendo kankyo chowa gata sekitan riyo system kanosei chosa. Senmomka haken A. kankyo chowa gata sekitan riyo system donyu shien jigyo (model jigyo) - Kanosei chosa no jizen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of the improvement of coal utilization technology and environmental preservation, the paper conducted the pre-survey of the introduction of coke oven gas desulfurization facilities in China and pre-survey of potentiality of the environmentally friendly type coal utilization system in India. The pre-survey in China was made for Anyang Steel Group Co. Ltd. and Laiwu Steel Group Co. Ltd. to judge their adaptability as site for the demonstrative project on the introduction of coke oven gas desulfurization facilities. As a result, it was confirmed that the former satisfied the conditions on Japan side such as the space for installation and prospect for fund raising. However, the amount of COG treatment was larger than that planned at Japan side, and it was found that as to the recovered sulfur, the company wanted the solid sulfur different from the fused sulfur planned at Japan side. In the survey in India, explanations were made to India of CFBC and the fluidized bed cement sintering system, bio-briquette production facilities, facilities for environmental measures, coal reforming technology, etc. At the same time, the site survey was made to examine/analyze possibilities of spread/development of Japan's CCT. (NEDO)

  16. FY 2001 report on the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Potential survey of the introduction of a processing/power generation system using ASR in the South region of Tochigi Prefecture; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Tochigi ken nanbu chiiki ni okeru ASR (Shuredda dust) wo nenryo to shita shori hatsuden system no donyu kanosei chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the consistent processing of waste automobile in Tochigi Prefecture and the neighboring area, survey/study were made of the thermal recycle using shredder dust, ASR (automobile shredder residue), as fuel as well as the material recycle. As to the amount of material recycle of waste automobile, the amount of potential recycle of iron, copper, plastic, etc. was estimated, and it was found out that the potential recycle of parts such as engine was 40-45%, that of iron scrap 35-40%, and that of ASR 20-25%. The amount of fuel (ASR amount) to be thrown into the gasification power generation system was set up at 150t. As the gasification power generation system, the pyrolysis gasifier and shaft kiln gasification melting furnace were selected. In the study of economical efficiency of the gasification power generation system, the following were considered: ASR processing price, plant cost, subsidy, running cost, char receiving price, power selling price, etc., but even in the case of the pyrolysis gasifier with highest valuation, both payback years and IRR did not reach the target. (NEDO)

  17. FY 1998 result report. Study of a total system for the development of superconductor power application technology (Feasibility study of commercialization of superconductivity technology and study of the introductory effect. Future superconductivity technology development in Japan); 1998 nendo seika hokokusho. Chodendo denryoku oyo gijutsu kaihatsu total system nado no kenkyu chodendo gijutsu no jitsuyoka kanosei oyobi donyu kokanado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As a part of the New Sunshine Project, 'an R and D project on superconductor power application technology,' an examinational study was made as a mini project to clarify the developmental course for commercialization of superconductor technology. The superconductor technology is being watched with interest as a technology in the 21st century. In the application to the electric power/energy field, in particular, expected are the energy saving effect by high operation efficiency, excellent environmentality, developmental potentiality of new equipment/system by the application of ferromagnetism, etc. Accordingly, the paper analytically arranged the needs of superconductor devices in Japan and abroad and the technology seeds corresponding to the needs, and prepared the developmental subjects of superconductor technology. These developmental steps and the mutual relationship were expressed in an R and D framework. At the same time, as to the superconductivity, a survey outlined the projects carried out in each government office in Japan. The future developmental course was indicated, and proposals were made on the equipment/system as object which are the subjects for urgent development for commercialization. (NEDO)

  18. FY 1998 result report. Study of a total system for the development of superconductor power application technology (Feasibility study of commercialization of superconductivity technology and study of the introductory effect. Future superconductivity technology development in Japan); 1998 nendo seika hokokusho. Chodendo denryoku oyo gijutsu kaihatsu total system nado no kenkyu chodendo gijutsu no jitsuyoka kanosei oyobi donyu kokanado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As a part of the New Sunshine Project, 'an R and D project on superconductor power application technology,' an examinational study was made as a mini project to clarify the developmental course for commercialization of superconductor technology. The superconductor technology is being watched with interest as a technology in the 21st century. In the application to the electric power/energy field, in particular, expected are the energy saving effect by high operation efficiency, excellent environmentality, developmental potentiality of new equipment/system by the application of ferromagnetism, etc. Accordingly, the paper analytically arranged the needs of superconductor devices in Japan and abroad and the technology seeds corresponding to the needs, and prepared the developmental subjects of superconductor technology. These developmental steps and the mutual relationship were expressed in an R and D framework. At the same time, as to the superconductivity, a survey outlined the projects carried out in each government office in Japan. The future developmental course was indicated, and proposals were made on the equipment/system as object which are the subjects for urgent development for commercialization. (NEDO)

  19. Fiscal 1999 basic survey report for promotion of joint implementation. Basic survey for promotion of joint implementation (Feasibility study about CO2 emission reduction by introducing energy-efficient facilities into three leading paper and pulp plants in the Philippines); 1999 nendo Philippines kami pulp shuyo 3 kojo eno sho energy setsubi donyu ni yoru CO{sub 2} haishutsu sakugen ni kansuru FS chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A feasibility study is conducted on the assumption of introducing Japan's energy-saving technology into three leading paper and pulp plants in the Philippines for a reduction in greenhouse gas emissions. In the future, the effort will be associated with the clean development mechanism (CDM). The three target plants are TIPCO (Trust International Paper Corporation), UPPC (United Pulp and Paper Co., Inc.), and CCP (Container Corporation of the Philippines). The energy-saving facilities to be installed involve energy-efficient screens, variable-speed motors, conversion of winder unwinding sections into rheostatic brakes, hermetic design for dryer hoods, exhaust heat recovery facilities, etc. A study of the plant and equipment investment standards of the respective corporations indicates that energy-saving alone will not realize a full payback. It will be necessary, therefore, to have the project implemented as a CDM activity for a transfer from the Philippines of some CO2 emission reduced amount credit for Japan to bear a part of the necessary funds. Since the CDM framework and the value of reduced amount credit are not clear at the current stage, negotiations will have to be furthered about Japan's share of funds etc. as soon as the situation becomes clear. Since the Philippine Government is not well-disposed towards CDM, there is no possibility that this project will be approved as a CDM effort. (NEDO)