WorldWideScience

Sample records for kingdom steel foundry

  1. Technologies for decreasing the tap temperature to save energy in steel foundries

    Science.gov (United States)

    Biswas, Siddhartha

    Steel foundries are one of the most energy intensive industries. The increasing concerns over volatile energy cost and carbon dioxide emission have pushed foundries to improve efficiency and hence decrease electrical energy consumption. Statistical analysis of industrial survey data was combined with computational fluid dynamics (CFD) modeling to investigate the best industrial practices and opportunities to improve energy efficiency. Reducing tap temperature was identified as one of the important ways of reducing energy consumption. Steel foundries typically tap at 1650-1800°C (3000-3300°F) which is 100-250°C (150-450°F) higher than the pouring temperature. The steel temperature is elevated to compensate for the temperature loss associated with tapping, holding and transporting the liquid steel from the furnace to the pouring floor. Based on experimental investigations and CFD modeling of heat losses during holding in the ladle for different foundry practices, a spreadsheet calculator has been developed to calculate the optimum tap temperature for the specific foundry practices which will eliminate unnecessary superheating. The calculated results were compared and validated with industrial measurements. Improving the lining refractory is one significant way of reducing heat losses during holding of the steel in ladle. Silica sand linings are being used in steel foundries as an inexpensive and convenient material for short holding times and small volumes. The possibilities of improvements of silica sand linings by the addition of lower density cenospheres (hollow spheres), a byproduct of coal fired power plants, was studied through property measurements and laboratory trials.

  2. Phytoremediation potential of aquatic herbs from steel foundry effluent

    Directory of Open Access Journals (Sweden)

    N. Aurangzeb

    2014-12-01

    Full Text Available Discharge of industrial effluents in aquatic environments is a serious threat to life due to toxic heavy metals. Plants can be used as cheap phytoremedients in comparison to conventional technologies. The present study was conducted to check the phytoremediation capability of two free-floating plants, i.e., Pistia stratiotes and Eichhornia crassipes, for the removal of heavy metals from steel effluent by using Atomic Absorption Spectrophotometry. P. stratiotes was able to remove some of the heavy metals, showing the highest affinity for Pb and Cu with 70.7% and 66.5% efficiency, respectively, while E. crassipes proved to be the best phytoremediant for polluted water as its efficiency was greatest progressively for Cd, Cu, As, Al and Pb, i.e., 82.8%, 78.6%, 74%, 73% and 73%, respectively. In conclusion, aquatic plants can be a better candidate for phytoextraction from industrial effluents due to cost effectiveness.

  3. No evidence of increased risk of soft tissue sarcomas in the neighborhood of a steel foundry in Verona

    Directory of Open Access Journals (Sweden)

    Marta Benedetti

    2010-12-01

    Full Text Available The aim of the present study was to evaluate the possible association between occurrence of soft tissue sarcomas in Verona (Italy and residence near a steel foundry, whose emissions of dioxin-like compounds may be relevant. Exposure to total suspended particulate (TSP emitted from the plant as estimated by ADMS-urban dispersion model was used as an indirect index of exposure to dioxin-like compounds. Verona municipality was divided in six subareas according to the decreasing levels of estimated TSP exposure, and soft tissue sarcomas cases were mapped according to residence at time of diagnosis. Standardized incidence ratios were computed. No statistically significant departures between observed and expected cases were detected as illustrated by trend-test results.

  4. Health and safety at work in foundry companies

    Directory of Open Access Journals (Sweden)

    L. Wojtynek

    2011-07-01

    Full Text Available The article presents the identification and analysis of threats in the environment of the foundry at individual stages of the casts manufacturing process. A generalized model of the foundry was created in the system presentation including harmful and dangerous factors in the foundry technical workplace. This model can refer to an iron foundry and cast steel and small non-ferrous foundries, to modern foundries, with automatic moulding lines and to chill and pressure foundries where machines execute the majority of essential operations.

  5. Molecular Foundry

    Science.gov (United States)

    . New Study Indicates Greater Capacity for Carbon Storage in the Earth's Subsurface A team of Foundry minerals which make up the dominant clays in the Earth's deep subsurface. Doubling Down on Energy Storage identify molecular components within small volumes of biological samples, such as blood or urine. Industry

  6. [Health risk assessment of exposure to metals in the workers of the steel foundry and in the general population of Taranto (Italy)].

    Science.gov (United States)

    Soleo, Leonardo; Lovreglio, Piero; Panuzzo, Laura; D'Errico, Maria Nicolà; Basso, Antonella; Gilberti, Maria Enrica; Drago, Ignazio; Tomasi, Cesare; Apostoli, Pietro

    2012-01-01

    To study the urinary excretion of As, Cr, Mn, Co, Ni, Cu, Zn, Cd, Sn, Ba, Hg, Pb, Sb in workers at the Taranto integrated-cycle steel foundry and in subjects from the general population of Taranto, to assess the health risk posed by occupational exposure and environmental exposure, respectively, to these metals. The study included 49 steel foundry workers (exposed), working in the minerals and agglomerates pools, steel processing plants 1 and 2 and maritime plants, and 50 subjects belonging to the general population of Taranto resident at various distances from the factory (controls), randomly selected from the exposed subjects and controls enrolled in previous research conducted in 2005. A questionnaire was administered to all participants, enquiring into general characteristics, lifestyle, diet, and any medical conditions. Informed written consent to take part in the study was obtained from all subjects before enrolment. The results of environmental monitoring performed in 2005 in the workers' sectors, consisting of determining As, Cr, Mn, Ni, Cu, Zn, Cd and Pb in the respirable dust, revealed by both samplers applied in fixed positions and personal samplers, were considered. Urine samples were obtained from all participants on a Friday, to determine As and Cr by AAS and all the other metal elements by a multielement technique with ICP-MS. Urinary creatinine was also determined to make any necessary adjustments. All urine analyses were performed in 2005 within one month of urine collection. In the respirable dust, As and Cd were always within the LOD, whereas Cr, Mn, Ni, Cu and Pb were 1-2 orders of magnitude below the respective TLV-TWA of the ACGIH. Mn was the only metal element that presented significantly higher urinary concentrations in exposed subjects as compared to controls, although the values in both groups were in any case within the Italian reference range. Co, Cu, Zn, Sn and Sb showed significantly higher urinary concentrations in controls than in

  7. Environmental Protection Versus Foundry Engineering Practice

    Directory of Open Access Journals (Sweden)

    Maj M.

    2017-06-01

    Full Text Available • Theory and practice of environmental protection in the case of foundries in Europe and Asia • Experience resulting from the cooperation with the foundries in a few European countries, China and India • Phenomena and factors affecting the pollution of the natural environment and the implementation of measures aiming at the environmental protection. Every specialist dealing with foundry processes and their impact on environmental pollution must have encountered in their professional careers numerous situations in which the theory of environmental protection confronts the stark reality. The discrepancy between theory and practice can particularly be noticed in foundry engineering in developing countries where the contrasts between different countries and casting plants are extremely striking. The comparison of working conditions in European and Asian foundries provides a vast scope for further observations and analyses. Environmental protection seems not only a concern of manufacturers of castings, but also of their customers whose opinion exerts a significant influence on both the acceptability of working conditions and on the approach to environmental pollution adopted in metal casting industry. The article presents a number of examples of various outlooks on environmental issues in foundries manufacturing a wide range of cast steel and cast iron castings, where different technologies and production processes are applied.

  8. The Molecular Foundry (TMF)

    Data.gov (United States)

    Federal Laboratory Consortium — Founded in 2006 by the Department of Energy (DOE), the Molecular Foundry is a critical part of the DOE's National Nanotechnology Initiative, a multi-agency framework...

  9. Energy conservation in foundry

    International Nuclear Information System (INIS)

    Natu, V.M.

    1994-01-01

    In any foundry, the cost of fuel in the form of coal, oil or electrical power, is about 10 to 15% of the cost of the product. Saving of the order of 30 to 50% can be achieved in energy by reducing consumption of fuel and increasing efficiency. This has been illustrated by describing 4 examples in foundry industry. In each case, saving in terms of rupees is also indicated. (N.B.)

  10. FOUNDRY WASTE MANAGEMENT

    Directory of Open Access Journals (Sweden)

    Borut Kosec

    2008-06-01

    Full Text Available Waste management in foundries is gaining a higher ecological and economical importance. Waste is becoming an increasingly traded product, where excellent profits can be made. Due to the cost reduction and successful business operation in companies, waste has to be regenerated and used again as a material to the maximum possible extent. Such research is long lasting and expensive and is a great challenge for companies. In the frame of our research, a total waste management case study for the Slovenian foundry Feniks was carried out. From the sustainable development point of view, waste management is most suitable, since it ensures the material utilization of waste, reduces the consumption of natural renewable or non-renewable resources and makes efficient production capacity utilization possible. Properly treated ecologically safe waste with a suitable physical characteristic, long-term existence, is a substitute for natural materials. Sand, dust, slag and other mineral waste from foundries are increasingly being used as materials in other industries. The foundry Feniks was awarded with certification of the environmental management system according to the standard SIST EN ISO 14001 and confirmed its environmental credentials.

  11. JPL Innovation Foundry

    Science.gov (United States)

    Sherwood, Brent; McCleese, Daniel

    2012-01-01

    Space science missions are increasingly challenged today: in ambition, by increasingly sophisticated hypotheses tested; in development, by the increasing complexity of advanced technologies; in budgeting, by the decline of flagship-class mission opportunities; in management, by expectations for breakthrough science despite a risk-averse programmatic climate; and in planning, by increasing competition for scarce resources. How are the space-science missions of tomorrow being formulated? The paper describes the JPL Innovation Foundry, created in 2011, to respond to this evolving context. The Foundry integrates methods, tools, and experts that span the mission concept lifecycle. Grounded in JPL's heritage of missions, flight instruments, mission proposals, and concept innovation, the Foundry seeks to provide continuity of support and cost-effective, on-call access to the right domain experts at the right time, as science definition teams and Principal Investigators mature mission ideas from "cocktail napkin" to PDR. The Foundry blends JPL capabilities in proposal development and concurrent engineering, including Team X, with new approaches for open-ended concept exploration in earlier, cost-constrained phases, and with ongoing research and technology projects. It applies complexity and cost models, projectformulation lessons learned, and strategy analyses appropriate to each level of concept maturity. The Foundry is organizationally integrated with JPL formulation program offices; staffed by JPL's line organizations for engineering, science, and costing; and overseen by senior Laboratory leaders to assure experienced coordination and review. Incubation of each concept is tailored depending on its maturity and proposal history, and its highest leverage modeling and analysis needs.

  12. JPL Innovation Foundry

    Science.gov (United States)

    Sherwood, Brent; McCleese, Daniel

    2013-08-01

    Space science missions are increasingly challenged today: in ambition, by increasingly sophisticated hypotheses tested; in development, by the increasing complexity of advanced technologies; in budgeting, by the decline of flagship-class mission opportunities; in management, by expectations for breakthrough science despite a risk-averse programmatic climate; and in planning, by increasing competition for scarce resources. How are the space-science missions of tomorrow being formulated? The paper describes the JPL Innovation Foundry, created in 2011, to respond to this evolving context. The Foundry integrates methods, tools, and experts that span the mission concept lifecycle. Grounded in JPL's heritage of missions, flight instruments, mission proposals, and concept innovation, the Foundry seeks to provide continuity of support and cost-effective, on-call access to the right domain experts at the right time, as science definition teams and Principal Investigators mature mission ideas from "cocktail napkin" to PDR. The Foundry blends JPL capabilities in proposal development and concurrent engineering, including Team X, with new approaches for open-ended concept exploration in earlier, cost-constrained phases, and with ongoing research and technology projects. It applies complexity and cost models, project-formulation lessons learned, and strategy analyses appropriate to each level of concept maturity. The Foundry is organizationally integrated with JPL formulation program offices; staffed by JPL's line organizations for engineering, science, and costing; and overseen by senior Laboratory leaders to assure experienced coordination and review. Incubation of each concept is tailored depending on its maturity and proposal history, and its highest-leverage modeling and analysis needs.

  13. European MEMS foundries

    Science.gov (United States)

    Salomon, Patric R.

    2003-01-01

    According to the latest release of the NEXUS market study, the market for MEMS or Microsystems Technology (MST) is predicted to grow to $68B by the year 2005, with systems containing these components generating even higher revenues and growth. The latest advances in MST/MEMS technology have enabled the design of a new generation of microsystems that are smaller, cheaper, more reliable, and consume less power. These integrated systems bring together numerous analog/mixed signal microelectronics blocks and MEMS functions on a single chip or on two or more chips assembled within an integrated package. In spite of all these advances in technology and manufacturing, a system manufacturer either faces a substantial up-front R&D investment to create his own infrastructure and expertise, or he can use design and foundry services to get the initial product into the marketplace fast and with an affordable investment. Once he has a viable product, he can still think about his own manufacturing efforts and investments to obtain an optimized high volume manufacturing for the specific product. One of the barriers to successful exploitation of MEMS/MST technology has been the lack of access to industrial foundries capable of producing certified microsystems devices in commercial quantities, including packaging and test. This paper discusses Multi-project wafer (MPW) runs, requirements for foundries and gives some examples of foundry business models. Furthermore, this paper will give an overview on MST/MEMS services that are available in Europe, including pure commercial activities, European project activities (e.g. Europractice), and some academic services.

  14. Foundry Coating Technology: A Review

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Tiedje, Niels Skat

    2011-01-01

    is important. In this review, a detailed description of these topics and examples are provided where necessary. A potential area of research in foundry coating development, using sol-gel process is suggested. The application of sol-gel technology in the development of foundry coatings is a novel approach....

  15. Foundries and environmental economy

    Energy Technology Data Exchange (ETDEWEB)

    Caglioti, V

    1974-01-01

    There is a growing emphasis on the recycling of natural resources. For example, the reprocessing of scrap iron involves an average saving of 74% of the energy used in ore reduction and an 84% decrease in pollution output. This calls for an approach to manufacturing that will favor the recycling of raw materials used. A publication of the American Foundrymen's Society lists 450 substances for which there are maximum permissible limits in the foundry work environment. It has been estimated that in Italy, on the average, about 20% of the cost of a manufacturing plant must now be allocated to pollution abatement equipment. Interdisciplinary communication where engineers can converse with physicists, chemists and environmentalists, and vice versa is discussed. Environmentalism also cannot be considered an isolation from the need to regulate the standard of living and to understand and influence human behavior.

  16. JPL Innovation Foundry

    Science.gov (United States)

    Sherwood, Brent; McCleese, Daniel J.

    2012-01-01

    NASA supports the community of mission principal investigators by helping them ideate, mature, and propose concepts for new missions. As NASA's Federally Funded Research and Development Center (FFRDC), JPL is a primary resource for providing this service. The environmental context for the formulation lifecycle evolves continuously. Contemporary trends include: more competitors; more-complex mission ideas; scarcer formulation resources; and higher standards for technical evaluation. Derived requirements for formulation support include: stable, clear, reliable methods tailored for each stage of the formulation lifecycle; on-demand access to standout technical and programmatic subject-matter experts; optimized, outfitted facilities; smart access to learning embodied in a vast oeuvre of prior formulation work; hands-on method coaching. JPL has retooled its provision of integrated formulation lifecycle support to PIs, teams, and program offices in response to this need. This mission formulation enterprise is the JPL Innovation Foundry.

  17. Combinatorial optimization in foundry practice

    Science.gov (United States)

    Antamoshkin, A. N.; Masich, I. S.

    2016-04-01

    The multicriteria mathematical model of foundry production capacity planning is suggested in the paper. The model is produced in terms of pseudo-Boolean optimization theory. Different search optimization methods were used to solve the obtained problem.

  18. Ergonomic Improvements for Foundries

    Energy Technology Data Exchange (ETDEWEB)

    Frank Peters; Patrick Patterson

    2002-06-18

    The goal of this project was to make improvements to the production systems of the steel casting industry through ergonomic improvements. Because of the wide variety of products, the wide range of product sizes, and the relatively small quantities of any particular product, manual operations remain a vital part of the production systems of the steel casting companies. Ergonomic improvements will assist the operators to more efficiently and consistently produce quality products.

  19. Qualitative characteristics of foundry dusts

    Directory of Open Access Journals (Sweden)

    K. Nowacki

    2018-01-01

    Full Text Available Recycling has become a top priority research task in highly developed countries, addressed from the perspective of environmental protection as well as cost-effectiveness of products. In many countries, including Poland, landfilling is still commonly accepted as a method of choice for waste neutralisation. This paper presents results of studies on the environmental impact of iron-bearing foundry waste in the event of its landfill disposal.

  20. Environmental Protection Versus Foundry Engineering Practice

    OpenAIRE

    Maj M.; Werrtz J.; Piekło J.

    2017-01-01

    • Theory and practice of environmental protection in the case of foundries in Europe and Asia • Experience resulting from the cooperation with the foundries in a few European countries, China and India • Phenomena and factors affecting the pollution of the natural environment and the implementation of measures aiming at the environmental protection. Every specialist dealing with foundry processes and their impact on environmental pollution must have encountered in their professional careers n...

  1. Wastes Characterisation from Foundry Activities on European Level

    International Nuclear Information System (INIS)

    Andres, I.; Ruiz, C.; Ibanez, R.; Viguri, J.; Irabien, A.

    1999-01-01

    This work presents The results of the eco toxicological characterisation of 22 defined wastes from steel foundry activities. The wastes have been selected from three processes, steel mill (smelting). sand casting and cleaning and finishing of steel products,with the common characteristics of represent an important industrial activity in the area and generated the wastes considered in this study. The eco toxicological characterisation obtained applying the Spanish regulations on hazardous waste is compared to the hazardous attributions considered by the European Union in order to characterise a waste as hazardous (non hazardous). The results allow to conclude that a acceptable concordance between both methodologies is reached and remark the need to split the broad generic types of wastes given by the Spanish regulation (Eco toxic / non eco toxic) into clearly identifiable specific types of waste

  2. Design and Fabrication of a Foundry Sand Mixer Using Locally ...

    African Journals Online (AJOL)

    Most small foundry shops mix their sand manually which is not efficient since homogenous mix cannot be guaranteed and even when foundry mixer are available most of them are imported costing the nation huge foriegn exchange. A foundry sand mixer capable of mixing foundry sand has been designed and fabricated ...

  3. Otimização da programação de cargas de forno em uma fábrica de fundição em aço-inox Optimizing the scheduling of furnace loadings in a inox-steel foundry

    Directory of Open Access Journals (Sweden)

    Raida de Jesus Silva

    2004-04-01

    Full Text Available Neste trabalho apresenta-se uma abordagem para otimizar a programação de cargas de forno em fundições de mercado de pequeno porte. Tal abordagem consiste, basicamente, em definir a programação dos fornos para produzir uma carteira de pedidos composta de diversas peças em ligas metálicas variadas, de maneira a maximizar a produtividade (ou a margem de contribuição ao lucro e satisfazer prazos de entrega e restrições de processo. O procedimento proposto é baseado na teoria dos problemas de corte e empacotamento; ele combina uma heurística construtiva gulosa com o clássico problema da mochila. Para validá-lo, um estudo de caso foi realizado numa fundição em aço-inox localizada em São Carlos, SP. Os resultados da simulação de duas semanas de produção da empresa mostraram que o procedimento é capaz de produzir soluções melhores do que as utilizadas pela empresa.This study presents an approach to optimize the scheduling of furnace loadings in small size foundries. The approach consists of determining a furnace scheduling to produce all ordered items in such a way as to maximize productivity (or profit contribution and satisfy due dates and process restraints. It is based on the theory of cutting and packing problems; it combines a greedy constructive heuristic and the classical knapsack problem. To validate the approach, a case study was developed in a inox-steel foundry located in São Carlos, SP. The results obtained simulating two weeks of the company production showed that the procedure is able to generate better solutions than the ones used by the company.

  4. SEARCH OF COMPOSITIONS OF FOUNDRY GRADES

    Directory of Open Access Journals (Sweden)

    O. S. Komarov

    2014-01-01

    Full Text Available Comparative researches of foundry paints showed that the most acceptable basis for them is disthenesillimanite and it is possible to use sodium aluminate solution as a binding agent.

  5. Ergonomic Improvements for Foundries; FINAL

    International Nuclear Information System (INIS)

    Frank Peters; Patrick Patterson

    2002-01-01

    The goal of this project was to make improvements to the production systems of the steel casting industry through ergonomic improvements. Because of the wide variety of products, the wide range of product sizes, and the relatively small quantities of any particular product, manual operations remain a vital part of the production systems of the steel casting companies. Ergonomic improvements will assist the operators to more efficiently and consistently produce quality products

  6. International negotiations in the foundry engineering

    Directory of Open Access Journals (Sweden)

    L. Wojtynek

    2008-04-01

    Full Text Available The aim of this paper is to introduce the essence of negotiations in general, which could find it’s application in foundry engineering. The paper is the result of long cooperation of the authors with foundry engineering and their participation in negotiations between the domestic and foreign companies. In this paper the essence and the rules of negotiations have been introduced. It presents also the skills and abilities of the negotiators. The cycle of negotiations and the following stages of negotiations have been also described. The authors have presented the characteristics of negotiations led by the partners from different parts of the world with particular emphasize on Asian and European countries as with these partners the negotiations in Polish foundries are mainly led.

  7. A Study of the Cold Resistance of Pipe Coiled Stock Produced at Foundry-Rolling Works. Part 2

    Science.gov (United States)

    Bagmet, O. A.; Naumenko, V. V.; Smetanin, K. S.

    2018-03-01

    Results of a study of coiled stock from low-carbon steels alloyed with manganese and silicon and different additives of niobium and titanium are presented. The coiled stock is produced at foundry-rolling works by the method of direct rolling of thin slabs right after their continuous casting. The microdeformation of the crystal lattice and the crystallographic texture are determined. The conditions of formation of the most favorable structure and texture in the steels are specified.

  8. 77 FR 32998 - Foundry Coke From China

    Science.gov (United States)

    2012-06-04

    ... China Determination On the basis of the record \\1\\ developed in the subject five-year review, the United... China would be likely to lead to continuation or recurrence of material injury to an industry in the... Publication 4326 (May 2012), entitled Foundry Coke from China: Investigation No. 731-TA-891 (Second Review...

  9. Environmental favourable foundries through maintenance activities

    Directory of Open Access Journals (Sweden)

    A. Saniuk

    2015-10-01

    Full Text Available Maintenance today contributes to the aim of sustainable development in society, including environmental and energy saving, safety and economical aspects. The main purpose of the paper is to present the role of maintenance in the realization of sustainable developing practices in a foundry industry. Maintenance offers numerous opportunities to reduce the influence of foundry processes on the natural environment and utilize resources more efficiently. Maintenance activities can help to reduce losses and thereby improve the efficiency of the processes used in the production of resources (e.g. raw materials, energy, etc., especially in areas such as: the choice of an appropriate strategy for the maintenance of machinery and equipment (e.g. reactive, preventive, proactive; inventory management of spare parts; lubrication management and management of technology media.

  10. Performance Steel Castings

    Science.gov (United States)

    2012-09-30

    system components to be built. Figure la shows the machine design . PSC-2012 Page 94 Glue Application Sheet Transfer Feed Elevator Figure la...Department of Defense such as cleats, ejection chutes , control arms, muzzle brakes, mortar components, clevises, tow bar clamps, ammo conveyor elements...Foundry and the members of Steel Founders’ Society of America. Abstract Weapon system designers and builders need advanced steel casting technology

  11. An investigation of waste foundry sand in asphalt concrete mixtures.

    Science.gov (United States)

    Bakis, Recep; Koyuncu, Hakan; Demirbas, Ayhan

    2006-06-01

    A laboratory study regarding the reuse of waste foundry sand in asphalt concrete production by replacing a certain portion of aggregate with WFS was undertaken. The results showed that replacement of 10% aggregates with waste foundry sand was found to be the most suitable for asphalt concrete mixtures. Furthermore, the chemical and physical properties of waste foundry sand were analysed in the laboratory to determine the potential effect on the environment. The results indicated that the investigated waste foundry sand did not significantly affect the environment around the deposition

  12. Steel

    International Nuclear Information System (INIS)

    Zorev, N.N.; Astafiev, A.A.; Loboda, A.S.; Savukov, V.P.; Runov, A.E.; Belov, V.A.; Sobolev, J.V.; Sobolev, V.V.; Pavlov, N.M.; Paton, B.E.

    1977-01-01

    Steels also containing Al, N and arsenic, are suitable for the construction of large components for high-power nuclear reactors due to their good mechanical properties such as good through-hardening, sufficiently low brittleness conversion temperature and slight displacement of the latter with neutron irradiation. Defined steels and their properties are described. (IHOE) [de

  13. Urinary 1-hydroxypyrene, a PAH biomarker in foundry workers

    DEFF Research Database (Denmark)

    Omland, Øyvind; Sherson, David; Hansen, Åse Marie

    1996-01-01

    Exposure to PAH in foundry workers has been studied by urinary 1-hydroxypyrene (HPU) levels, quantitatively measured by reversed phase HPLC. Seventy male foundry workers and 68 matched controls were investigated. Polycyclic aromatic hydrocarbon (PAH) exposure was defined by 17 breathing zone hygi...

  14. MEMS/MOEMS foundry services at INO

    Science.gov (United States)

    García-Blanco, Sonia; Ilias, Samir; Williamson, Fraser; Généreux, Francis; Le Noc, Loïc; Poirier, Michel; Proulx, Christian; Tremblay, Bruno; Provençal, Francis; Desroches, Yan; Caron, Jean-Sol; Larouche, Carl; Beaupré, Patrick; Fortin, Benoit; Topart, Patrice; Picard, Francis; Alain, Christine; Pope, Timothy; Jerominek, Hubert

    2010-06-01

    In the MEMS manufacturing world, the "fabless" model is getting increasing importance in recent years as a way for MEMS manufactures and startups to minimize equipment costs and initial capital investment. In order for this model to be successful, the fabless company needs to work closely with a MEMS foundry service provider. Due to the lack of standardization in MEMS processes, as opposed to CMOS microfabrication, the experience in MEMS development processes and the flexibility of the MEMS foundry are of vital importance. A multidisciplinary team together with a complete microfabrication toolset allows INO to offer unique MEMS foundry services to fabless companies looking for low to mid-volume production. Companies that benefit from their own microfabrication facilities can also be interested in INO's assistance in conducting their research and development work during periods where production runs keep their whole staff busy. Services include design, prototyping, fabrication, packaging, and testing of various MEMS and MOEMS devices on wafers fully compatible with CMOS integration. Wafer diameters ranging typically from 1 inch to 6 inches can be accepted while 8-inch wafers can be processed in some instances. Standard microfabrication techniques such as metal, dielectric, and semiconductor film deposition and etching as well as photolithographic pattern transfer are available. A stepper permits reduction of the critical dimension to around 0.4 μm. Metals deposited by vacuum deposition methods include Au, Ag, Al, Al alloys, Ti, Cr, Cu, Mo, MoCr, Ni, Pt, and V with thickness varying from 5 nm to 2 μm. Electroplating of several materials including Ni, Au and In is also available. In addition, INO has developed and built a gold black deposition facility to answer customer's needs for broadband microbolometric detectors. The gold black deposited presents specular reflectance of less than 10% in the wavelength range from 0.2 μm to 100 μm with thickness ranging from

  15. Producción de hierros nodulares ferríticos directamente de fundición partiendo de chatarra de acero de alto manganeso // Production of ferrítics nodular irons directly from foundry leaving of high manganese scrap steel

    Directory of Open Access Journals (Sweden)

    C. DeFranch

    1999-07-01

    ñinos; lo que necesitaría de una gran inversión en cuanto a extractores y procesadores de estos gases.Los factores críticos en el proceso que emplea óxido de hierro para la eliminación del manganeso son: temperatura,composición química del baño y elementos presentes en la escoria, con el mismo se han logrado eliminaciones del manganesode hasta un 80% del contenido inicial y fundiciones ferríticas con elongaciones de hasta un 23%.Palabras claves: hierro nodular, fundición___________________________________________________________________________AbstractThe production of nodular irons with main ferrític is usually achieved with the use of special arrabios with contained first floorof elements formadores of carbides, or by means of long and expensive thermal treatments. These arrabios has high prices, forwhat becomes necessary the search of more economic variants for the production of this material type. The objective of thiswork is the obtaining of this material using like load steel scrap, which has a price a lot but I lower.The structure of the womb in the nodular iron, depends on its chemical composition, its cooling speed, as well as of the formand quantity of graphite nodules. When is wanted a main ferrítics, the elements who make the perlitic estructure they shouldbe maintained in contents the lowest thing possible for less susecful this way the solidification according to the diagram.The scrap use outlines the problem of the present manganese levels in the same one (generally between 0.6 and 0.8%. Themanganese that is an element who make the perlitic estructure avoids the obtaining of high elongations since the womb itDr. Ing C. DeFranch, Dr. Ing. T. Rodríguez Moliner26would be never completely ferrític. It is for this reason that if she/he wants himself to use steel scrap as load material it isnecessary the study in ways of eliminating it of the bathroom.For the elimination of the manganese diverse references exist in the literature to processes

  16. New EUROPRACTICE microsystem design and foundry services

    Science.gov (United States)

    Salomon, Patric R.; Beernaert, Dirk; Turner, Rob

    2000-08-01

    The microsystems market for MST is predicted to grow to 38 billion dollars by the year 2002, with systems containing these components generating even higher revenues and growth. One of the barriers to successful exploitation of this technology has been the lack of access to industrial foundries capable of producing certified microsystems devices in commercial quantities. To overcome this problem, the European Commission has started the EUROPRACTICE program in 1996 with the installation of manufacturing clusters and demonstration activities to provide access to microsystems foundry services for European small and medium sized companies (SMEs). Since 1996, there has been a shift form providing 'broad technology offers' and 'raising awareness fro microsystem capabilities' to 'direct support of design needs' and 'focused services' which allow SMEs to use even complex microsystems technologies to implement their products, The third phase of EUROPRACTICE has just been launched, and contains 5 Manufacturing Clusters, 12 Designs Houses, and 7 Competence Centers, each working in different application/technology areas. The EUROPRACTICE program will be presented together with a detail description of the capabilities of the participants and information on how to access their services.

  17. Wafer-shape metrics based foundry lithography

    Science.gov (United States)

    Kim, Sungtae; Liang, Frida; Mileham, Jeffrey; Tsai, Damon; Bouche, Eric; Lee, Sean; Huang, Albert; Hua, C. F.; Wei, Ming Sheng

    2017-03-01

    As device shrink, there are many difficulties with process integration and device yield. Lithography process control is expected to be a major challenge due to tighter overlay and focus control requirement. The understanding and control of stresses accumulated during device fabrication has becoming more critical at advanced technology nodes. Within-wafer stress variations cause local wafer distortions which in turn present challenges for managing overlay and depth of focus during lithography. A novel technique for measuring distortion is Coherent Gradient Sensing (CGS) interferometry, which is capable of generating a high-density distortion data set of the full wafer within a time frame suitable for a high volume manufacturing (HVM) environment. In this paper, we describe the adoption of CGS (Coherent Gradient Sensing) interferometry into high volume foundry manufacturing to overcome these challenges. Leveraging this high density 3D metrology, we characterized its In-plane distortion as well as its topography capabilities applied to the full flow of an advanced foundry manufacturing. Case studies are presented that summarize the use of CGS data to reveal correlations between in-plane distortion and overlay variation as well as between topography and device yield.

  18. Small Scale Foundries in Ghana: The challenges

    Directory of Open Access Journals (Sweden)

    Anthony ANDREWS

    2012-08-01

    Full Text Available Small Scale Foundries (SSFs have been in existence for several years in Ghana. The industry has created several jobs for the people of Ghana and has minimized the burden on government to find ways of disposing scrap metals generated within the country. While scrap metals are still being exported, the quantity exported has decreased as a result of recycling by foundrymen in producing various parts. The government of Ghana has not paid special attention to this industry. Nevertheless, individuals and private investors are heavily involved in producing several thousands of tonnes of castings annually generating revenue for the government through taxation as well as helping with metal waste disposal. Metal cast products are sold both locally and internationally to neighbouring countries. The industry is however faced with numerous challenges. These include quality issues due to lack of technical know-how, access to funding from both government and private financial institutions and foundry waste management. To promote this industry, government and private financial institutions must be encouraged to come on board. Policies must be established and proper training programme developed to improve and promote this technology. This could go a long way in reducing the high unemployment rate in Ghana.

  19. Hybrid foundry patterns of bevel gears

    Directory of Open Access Journals (Sweden)

    Budzik G.

    2007-01-01

    Full Text Available Possibilities of making hybrid foundry patterns of bevel gears for investment casting process are presented. Rapid prototyping of gears with complex tooth forms is possible with the use of modern methods. One of such methods is the stereo-lithography, where a pattern is obtained as a result of resin curing with laser beam. Patterns of that type are applicable in precision casting. Removing of stereo-lithographic pattern from foundry mould requires use of high temperatures. Resin burning would generate significant amounts of harmful gases. In case of a solid stereo-lithographic pattern, the pressure created during gas burning may cause the mould to crack. A gas volume reduction may be achieved by using patterns of honeycomb structure. However, this technique causes a significant worsening of accuracy of stereo-lithographic patterns in respect of their dimensions and shape. In cooperation with WSK PZL Rzeszów, the Machine Design Department of Rzeszow University of Technology carried out research on the design of hybrid stereo-lithographic patterns. Hybrid pattern consists of a section made by stereo-lithographic process and a section made of casting wax. The latter material is used for stereo-lithographic pattern filling and for mould gating system. The hybrid pattern process consists of two stages: wax melting and then the burn-out of stereolithographic pattern. Use of hybrid patterns reduces the costs of production of stereolithographic patterns. High dimensional accuracy remains preserved in this process.

  20. Commercial negotiations in the foundry engineering

    Directory of Open Access Journals (Sweden)

    L. Wojtynek

    2008-10-01

    Full Text Available The article presents the process of commercial negotiations paying attention to the negotiation itself as well as to its basic elements. The specificity of the Polish foundries’ main negotiation partners from The European Union, who are the deliverers of diverse casting range, was specified. The most important cultural factors, which determine the process of negotiations conducted by the representatives of various cultural groups, were analysed. The understanding of cultural differences and adapting to them while negotiating are important factors which constitute the parties’ negotiation process. The meaning of price in the commercial negotiation process was described. The elements of sale process and the factors which influence the casts price were enumerated. What is more, the main methods of determining price were characterized. The essential problems connected with conducting the price negotiations in foundries were indicated.

  1. Maintenance system improvement in cast iron foundry

    Directory of Open Access Journals (Sweden)

    S. Kukla

    2011-07-01

    Full Text Available The work presents the issue of technical equipment management in an iron foundry basing on the assumptions of the TPM system (Total Productive Maintenance. Exploitation analysis of automatic casting lines has been carried out and their work’s influence on the whole production system’s functioning has been researched. Within maintenance system improvement, implementation of autonomic service and planned lines’ review have been proposed in order to minimize the time of breakdown stoppages. The SMED method was used to optimize changeover time, and the OEE (Overall Equipment Effectiveness was applied to evaluate the level of resources usage before and after implementing changes. Further, the influence of the maintenance strategy of casting devices’ efficiency on own costs of casting manufac- ture was estimated.

  2. Ion traps fabricated in a CMOS foundry

    Energy Technology Data Exchange (ETDEWEB)

    Mehta, K. K.; Ram, R. J. [Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Eltony, A. M.; Chuang, I. L. [Center for Ultracold Atoms, Research Laboratory of Electronics and Department of Physics, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Bruzewicz, C. D.; Sage, J. M., E-mail: jsage@ll.mit.edu; Chiaverini, J., E-mail: john.chiaverini@ll.mit.edu [Lincoln Laboratory, Massachusetts Institute of Technology, Lexington, Massachusetts 02420 (United States)

    2014-07-28

    We demonstrate trapping in a surface-electrode ion trap fabricated in a 90-nm CMOS (complementary metal-oxide-semiconductor) foundry process utilizing the top metal layer of the process for the trap electrodes. The process includes doped active regions and metal interconnect layers, allowing for co-fabrication of standard CMOS circuitry as well as devices for optical control and measurement. With one of the interconnect layers defining a ground plane between the trap electrode layer and the p-type doped silicon substrate, ion loading is robust and trapping is stable. We measure a motional heating rate comparable to those seen in surface-electrode traps of similar size. This demonstration of scalable quantum computing hardware utilizing a commercial CMOS process opens the door to integration and co-fabrication of electronics and photonics for large-scale quantum processing in trapped-ion arrays.

  3. The restoration of an Argonne National Laboratory foundry

    International Nuclear Information System (INIS)

    Shearer, T.; Pancake, D.; Shelton, B.

    1997-01-01

    The Environmental Management Operations' Waste Management Department (WMD) at Argonne National Laboratory-East (ANL-E) undertook the restoration of an unused foundry with the goal of restoring the area for general use. The foundry was used in the fabrication of reactor components for ANL's research and development programs; many of the items fabricated in the facility were radioactive, thereby contaminating the foundry equipment. This paper very briefly describes the dismantling and decontamination of the facility. The major challenges associated with the safe removal of the foundry equipment included the sheer size of the equipment, a limited overhead crane capability (4.5 tonne), the minimization of radioactive and hazardous wastes, and the cost-effective completion of the project, the hazardous and radioactive wastes present, and limited process knowledge (the facility was unused for many years)

  4. Web-based expert system for foundry pollution prevention

    Science.gov (United States)

    Moynihan, Gary P.

    2004-02-01

    Pollution prevention is a complex task. Many small foundries lack the in-house expertise to perform these tasks. Expert systems are a type of computer information system that incorporates artificial intelligence. As noted in the literature, they provide a means of automating specialized expertise. This approach may be further leveraged by implementing the expert system on the internet (or world-wide web). This will allow distribution of the expertise to a variety of geographically-dispersed foundries. The purpose of this research is to develop a prototype web-based expert system to support pollution prevention for the foundry industry. The prototype system identifies potential emissions for a specified process, and also provides recommendations for the prevention of these contaminants. The system is viewed as an initial step toward assisting the foundry industry in better meeting government pollution regulations, as well as improving operating efficiencies within these companies.

  5. Foundry based approach for InP based PIC development

    NARCIS (Netherlands)

    Smit, M.K.

    2014-01-01

    Europe is making significant investments in development of generic photonic foundry platform infrastructures for InP-based and Silicon Photonic ICs. Here we present the present status for the InP-based JePPIX platform.

  6. Guide to energy efficiency opportunities in Canadian foundries

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    In Canada, the foundry sector employs about 15000 people and most of the companies are members of the Canadian Foundry Association (CFA). The CFA is committed to reducing its greenhouse gas emissions and is therefore looking for energy savings which, in addition to reducing emissions, would help the industry save costs and improve its competitiveness. The aim of this document is to provide operators with a guide to improving energy efficiency in their foundries. The report provides guidance on carrying out energy audits, gathering energy saving ideas, prioritizing projects, and charting the course of improved energy performance. Many different energy saving ideas for many kinds of operation are presented in this guidebook as a help to operators in finding where they could improve their energy efficiency; references to energy saving methods from all over the world are provided. This guidebook is a useful tool for helping foundry operators improve energy efficiency in their operations.

  7. Development of risk assessment tool for foundry workers.

    Science.gov (United States)

    Mohan, G Madhan; Prasad, P S S; Mokkapati, Anil Kumar; Venkataraman, G

    2008-01-01

    Occupational ill-health and work-related disorders are predominant in manufacturing industries due to the inevitable presence of manual work even after several waves of industrial automation and technological advancements. Ergonomic risk factors and musculoskeletal disorders like low-back symptoms have been noted amongst foundry workers. The purpose of this study was to formulate and develop a Physical Effort Index to assess risk factor. The questionnaire tool applicable to foundry environment has been designed and validated. The data recorded through survey across the foundries has been subjected to regression analysis to correlate between proposed physical effort index and the standard Borg's Ratings of Perceived Exertion (RPE) scale. The physical efforts of sixty seven workers in various foundry shop floors were assessed subjectively. The 'Job factors' and 'Work environment' were the two major parameters considered in assessing the worker discomfort level at workplace. A relation between Borg's RPE scale and the above two parameters were arrived at, through regression analysis. The study demonstrates the prevalence of risk factors amongst foundry workers and the effectiveness of the proposed index in estimating the risk factor levels. RELEVANCE TO THE INDUSTRY: The proposed tool will assist foundry supervisors and managers to assess the risk factors and helps in better understanding of the workplace to avoid work-related disorders, ensuring better output.

  8. Metallurgy and foundry practice. German-English. With 40,000 citations. Metallurgie und Giessereitechnik. Deutsch-Englisch. Mit etwa 40,000 Wortstellen

    Energy Technology Data Exchange (ETDEWEB)

    Stoelzel, K [ed.

    1986-01-01

    The dictionary represents the German-English terminology of the broad field of metallurgy (the dressing of ores and fluxes, pig iron and steel making, powder and nonferrous metallurgy, forming processes etc.) as well as of the broad field of foundry practice. Apart from the theoretical fundamental principles emphasis is on the problems of materials working and materials testing. Moreover, the dictionary considers a number of technical terms concerning the hardening, surface treatment and corrosion of materials.

  9. 31. Introduction with adjacent production of foundry and rolling department of electrolysis shop

    International Nuclear Information System (INIS)

    Ivanov, A.V.

    1993-01-01

    The introduction with adjacent production of foundry and rolling department of electrolysis shop was conducted. The foundry machine was described. The chemical properties of aluminium for ferrous alloy production were defined.

  10. Reduced energy consumption for melting in foundries

    Energy Technology Data Exchange (ETDEWEB)

    Skov-Hansen, S.

    2007-09-15

    By improving the gating technology in traditional gating systems it is possible to reduce the amount of metal to be re-melted, and hence reduce the energy consumption for melting in foundries. Traditional gating systems are known for a straight tapered down runner a well base and 90 deg. bends in the runner system. In the streamlined gating systems there are no sharp changes in direction and a large effort is done to confine and control the flow of the molten metal during mould filling. Experiments in real production lines have proven that using streamlined gating systems improves yield by decreasing the poured weight compared to traditional layouts. In a layout for casting of valve housings in a vertically parted mould the weight of the gating system was reduced by 1,1kg which is a 20% weight reduction for the gating system. In a layout for horizontally parted moulds the weight of the gating system has been reduced by 3,7kg which is a weight reduction of 60% for the gating system. The experiments casting valve housings in ductile iron also proved that it is possible to lower the pouring temperature from 1400 deg. C to 1300 deg. C without the risk of cold runs. Glass plate fronted moulds have been used to study the flow of melt during mould filling. These experiments have also been used for studying the flow pattern when ceramic filters are used. The thorough study of the use of filters revealed that the metal passing through the filter is divided into a number of small jets. This proves that filters do not have the claimed positive effect on the flow of metal. The volumes necessary on either side of the filter is not filled till a backpressure is build up and results in formation of pressure shocks when backfilled. These pressure shocks result in more turbulence inside the casting than the same gating system with no filter. Not using filters can mean a reduction in poured weight of 0,6kg. To examine if the experiments using glass plate fronted moulds give

  11. Rationalization of foundry processes on the basis of simulation experiment

    Directory of Open Access Journals (Sweden)

    S. Kukla

    2008-10-01

    Full Text Available The paper presents results of research obtained on the basis of simulation experiment, whose aim was to analyze the performance of cast iron foundry. A simulation model of automobile industry foundry was made. The course of the following processes was analyzedin a computer model: preparation of liquid cast iron, forming and filling the moulds, cooling and stamping the castings, cleaning andfinishing treatment. The sheets of multi-criterion evaluation were prepared, where criteria and variants were assessed by meansof subjective point evaluation and fuzzy character evaluation. The paper presents an analysis example of finishing activities of castings realized in foundry on traditional machines and efficient presses and in cooperation. On the basis of reports from a simulation experiment information was achieved related to activities’ duration, load of accessible resources, the problems of storage and transport, bottle necks in the system and appearing queues in from of workplaces. The research used a universal modelling and simulation packet for productionsystems - ARENA.

  12. Prevalence of job strain among Indian foundry shop floor workers.

    Science.gov (United States)

    Mohan, G Madhan; Elangovan, S; Prasad, P S S; Krishna, P Rama; Mokkapati, Anil Kumar

    2008-01-01

    Global competition in manufacturing sector demand higher productivity levels. In this context, workers in this sector are set with high output targets, leading to job strain. In addition to the strain, hazardous conditions also prevail in some of the manufacturing processes like foundry activities. This paper attempts to appraise the prevalence of job strain among foundry shop floor workers in India with the help of Demands-Control model [8]. In this study, data was collected through a survey using 49-item Job Content Questionnaire (JCQ) [9], a widely used and well-validated test for job strain. Then the data was subjected to statistical analysis after ascertaining the reliability. This survey has revealed that 25% of workers in foundry were experiencing high job strain. Hazardous working conditions, limited decision making authority, etc. appear to be the main contributing factors for the higher levels of strain.

  13. Exposure of iron foundry workers to polycyclic aromatic hydrocarbons

    DEFF Research Database (Denmark)

    Omland, Øyvind; Sherson, D; Hansen, Å M

    1994-01-01

    Exposure to polycyclic aromatic hydrocarbons (PAHs) in foundry workers has been evaluated by determination of benzo(a)pyrene-serum albumin adducts and urinary 1-hydroxypyrene. Benzo(a)pyrene binding to albumin and 1-hydroxypyrene were quantitatively measured by enzyme linked immunosorbent assay...... (ELISA) and reverse phase high performance liquid chromatography (HPLC), respectively. 70 male foundry workers and 68 matched controls were investigated. High and low exposure groups were defined from breathing zone hygienic samples, consisting of 16 PAH compounds in particulate and gaseous phase. Mean...... total PAH was 10.40 micrograms/m3 in the breathing zone, and mean dust adsorbed PAH was 0.15 microgram/m. All carcinogenic PAH was adsorbed to dust. Median benzo(a)pyrene-albumin adduct concentrations (10-90% percentiles) were similar in foundry workers (smokers 0.55 (0.27-1.00) and non-smokers 0.58 (0...

  14. The AHP method used in assessment of foundry enterprise position

    Directory of Open Access Journals (Sweden)

    J. Szymszal

    2008-10-01

    Full Text Available Complex assessment of activity of a selected foundry enterprise based on a modern AHP (Analytic Hierarchy Process method has beenpresented. Having defined the areas of analysis, which include: marketing (products, distribution channels, sales organisation and client concentration, personnel (skills, managerial abilities, organisation climate, effectiveness of incentives, personnel fluctuations, production (availability of raw materials, technical level of production, effective use of production capacities, organisation and management (foundry structure, organisation culture, management performance, the analysis was made using the weighted sum of evaluations. The second step consisted in a comparative assessment of Foundry position using Saaty’s scale modified by Weber and the AHP method with examinationof a hierarchy structure involving the main (parent problem and its direct evolution into sub-problems. The assessment of Foundryposition made by AHP enables introducing changes and/or innovations which are expected to improve the overall productioneffectiveness.

  15. Modified polysaccharides as alternative binders for foundry industry

    Directory of Open Access Journals (Sweden)

    K. Kaczmarska

    2016-10-01

    Full Text Available Polysaccharides constitute a wide group of important polymers with many commercial applications, for example food packaging, fibres, coatings, adhesives etc. This review is devoted to the presentation of polysaccharide application in foundry industry. In this paper the selected properties of foundry moulding sand and core sand containing modified polysaccharides as binders are presented according to foreign literature data. Also, author’s own research about effect of using moulding sand binder consisting of modified polysaccharide (modified starch or its composition with non-toxic synthetic polymers are discussed. Based on technologies taken under consideration in this paper, it could be concluded that polysaccharides are suitable as an alternative for use as binder in foundry moulding applications.

  16. Management of Assortment Inventory Groups in Selected Foundry

    Directory of Open Access Journals (Sweden)

    Szymszal J.

    2015-09-01

    Full Text Available As experience shows the practical, reliable assessment and optimisation of total costs of logistical processes implemented in supply chains of foundry plants is a quite complex and complicated process, because it requires to enclose all, without exception, performed actions, including them in various reference cross-sections, systematic activities and finally transforming them in a totally homogenous collection. Only solid analysis and assessment of assortment management in logistical supply systems in foundry plants of particular assortment groups allows to lower the supply costs significantly. In the article the analysis and assessment of the newest implemented optimising algorithms are presented in the process stock management of selected material groups used in a production process of a chosen foundry plant. A practical solution to solve a problem of rotary stock cost minimisation is given as well as of costs while creating a stock with the usage of economical volume and value of order.

  17. Building biological foundries for next-generation synthetic biology.

    Science.gov (United States)

    Chao, Ran; Yuan, YongBo; Zhao, HuiMin

    2015-07-01

    Synthetic biology is an interdisciplinary field that takes top-down approaches to understand and engineer biological systems through design-build-test cycles. A number of advances in this relatively young field have greatly accelerated such engineering cycles. Specifically, various innovative tools were developed for in silico biosystems design, DNA de novo synthesis and assembly, construct verification, as well as metabolite analysis, which have laid a solid foundation for building biological foundries for rapid prototyping of improved or novel biosystems. This review summarizes the state-of-the-art technologies for synthetic biology and discusses the challenges to establish such biological foundries.

  18. Logic Foundry: Rapid Prototyping for FPGA-Based DSP Systems

    Directory of Open Access Journals (Sweden)

    Bhattacharyya Shuvra S

    2003-01-01

    Full Text Available We introduce the Logic Foundry, a system for the rapid creation and integration of FPGA-based digital signal processing systems. Recognizing that some of the greatest challenges in creating FPGA-based systems occur in the integration of the various components, we have proposed a system that targets the following four areas of integration: design flow integration, component integration, platform integration, and software integration. Using the Logic Foundry, a system can be easily specified, and then automatically constructed and integrated with system level software.

  19. Characterization and extraction of gold contained in foundry industrial wastes

    International Nuclear Information System (INIS)

    Vite T, J.; Vite T, M.; Diaz C, A.; Carreno de Leon, C.

    1999-01-01

    Gold was characterized and leached in foundry sands. These wastes are product among others of the automotive industry where they are used as molds material which are contaminated by diverse metals during the foundry. To fulfil the leaching process four coupled thermostat columns were used. To characterize the solid it was used the X-ray diffraction technique. For the qualitative analysis it was used the Activation analysis technique. Finally, for the study of liquors was used the Plasma diffraction spectroscopy (Icp-As) technique. The obtained results show that the process which was used the thermostat columns was more efficient, than the methods traditionally recommended. (Author)

  20. Manganese exposure in foundry furnacemen and scrap recycling workers

    DEFF Research Database (Denmark)

    Lander, F; Kristiansen, J; Lauritsen, Jens

    1999-01-01

    Cast iron products are alloyed with small quantities of manganese, and foundry furnacemen are potentially exposed to manganese during tapping and handling of smelts. Manganese is a neurotoxic substance that accumulates in the central nervous system, where it may cause a neurological disorder...

  1. Using lean methodologies for economically and environmentally sustainable foundries

    Directory of Open Access Journals (Sweden)

    R. M. Torielli

    2011-02-01

    Full Text Available Lean manufacturing is often seen as a set of tools that reduce the total cost and improve the quality of manufactured products. The lean management philosophy is one which targets waste reduction in every facet of the manufacturing business; however, only recently have studies linked lean management philosophies with improving environmental sustainability. These studies suggest that lean manufacturing is more than a set of lean tools that can optimize manufacturing efficiencies; it is a process and mindset that needs to be integrated into daily manufacturing systems to achieve sustainability. The foundry industry, as well as manufacturing in general, has significant challenges in the current regulatory and political climate with developing an economically and environmentally sustainable business model. Lean manufacturing has proven itself as a model for both economic sustainability and environmental stewardship. Several recent studies have shown that both lean and green techniques and “zero-waste” policies also lead to reductions in overall cost. While these strategies have been examined for general manufacturing, they have not been investigated in detail for the foundry industry. This paper will review the current literature and describe how lean and green can provide a relevant framework for environmentally and economically sustainable foundries. Examples of lean and green technologies and techniques which can be applied to foundries in a global context will be described.

  2. Granulated blast furnace slag – A boon for foundry industry

    African Journals Online (AJOL)

    Keywords: Silica sand; Blast Furnace Slag; Mould properties; Ferrous and nonferrous ... raw material for the production of cast components in foundry industries. ... applications for conserving natural resources and reduce the cost of the raw .... in an elevated temperature melting furnace with temperature values of 750 to.

  3. Abrasive Wear of Alloyed Cast Steels Applied for Heavy Machinery

    Directory of Open Access Journals (Sweden)

    Studnicki A.

    2015-03-01

    Full Text Available In the paper the results and analysis of abrasive wear studies were shown for two grades of cast steels: low-alloyed cast steel applied for heavy machinery parts such as housing, covers etc. and chromium cast steels applied for kinetic nodes of pin-sleeve type. Studies were performed using the modified in Department of Foundry pin-on-disc method.

  4. Effect of cast steel production metallurgy on the emergence of casting defects

    Directory of Open Access Journals (Sweden)

    L. Čamek

    2016-10-01

    Full Text Available The paper documents metallurgical possibilities of high alloy cast steel production in open induction medium frequency furnaces and an electric arc furnace in a gravity die casting foundry. The observation was focused on the emergence of gas defects in steel castings. The content of gases achieved during the metallurgical processes was evaluated for every unit of the production equipment and the casting ladle before casting into disposable sand moulds. The sand mould area was considered to be constant. The aim was to evaluate the current metallurgical possibilities of affecting the content of gases in high alloy cast steel in the current technical conditions of the foundry.

  5. Foundry fabricated photonic integrated circuit optical phase lock loop.

    Science.gov (United States)

    Bałakier, Katarzyna; Fice, Martyn J; Ponnampalam, Lalitha; Graham, Chris S; Wonfor, Adrian; Seeds, Alwyn J; Renaud, Cyril C

    2017-07-24

    This paper describes the first foundry-based InP photonic integrated circuit (PIC) designed to work within a heterodyne optical phase locked loop (OPLL). The PIC and an external electronic circuit were used to phase-lock a single-line semiconductor laser diode to an incoming reference laser, with tuneable frequency offset from 4 GHz to 12 GHz. The PIC contains 33 active and passive components monolithically integrated on a single chip, fully demonstrating the capability of a generic foundry PIC fabrication model. The electronic part of the OPLL consists of commercially available RF components. This semi-packaged system stabilizes the phase and frequency of the integrated laser so that an absolute frequency, high-purity heterodyne signal can be generated when the OPLL is in operation, with phase noise lower than -100 dBc/Hz at 10 kHz offset from the carrier. This is the lowest phase noise level ever demonstrated by monolithically integrated OPLLs.

  6. Environmental characterization foundry sands used in sanitary landfills

    International Nuclear Information System (INIS)

    Domingues, L.G.F.; Ferreira, G.C.S.; Pires, M.S.G.; Teixeira, I.; Carnin, R.; Sarro, W.S.

    2016-01-01

    The national solid waste policy recommends reducing solid waste generation and reusing them in different applications. Preliminary studies show that the foundry sand generated from cast metal parts undercut, has excellent applicability in grain size stabilization of soils for geotechnical functions, and therefore, should not be discarded as waste. This study aimed at environmental characterization of two lots of waste foundry sand (WFS), from different industries, to the particle size stabilization of a clayey soil for use in coverage of solid waste in landfills. The methodology included physicochemical characterization tests (grain size, permeability, XRF and heavy metals) and environmental (NBR 10004: 2004, NBR 10005: 2004, NBR 10006: 20004 and acute toxicity with Vibrio fischeri). The results prove the environmental viability of using these lots of WFS as functional material in the composition of landfills. (author)

  7. Logistics of Materials Flow in an Iron Foundry

    Directory of Open Access Journals (Sweden)

    Kukla S.

    2013-09-01

    Full Text Available The article presents issues related to creating and realizing added value by logistic processes and processing in a casting enterprise. It discusses possibilities of improving systems of casts production by evaluating labour intensity of casts manufacture and analyzing manufacturing prime costs. Operations with added value, processes indirectly creating added value and operations without added value have been specified. The problem was presented on the example of materials flow design in a foundry, where casts are manufactured in expendable moulds and using automated foundry lines. On the basis of the Pareto analysis, a group of casts was specified whose manufacture significantly influences the functioning of the whole enterprise. Finishing treatment operations have been particularly underlined, as they are performed away from the line and are among the most labour-consuming processes during casts production.

  8. Determination of thermal conductivity in foundry mould mixtures

    Directory of Open Access Journals (Sweden)

    G. Solenički

    2010-01-01

    Full Text Available For a thorough understanding of the behaviour of foundry mould mixtures, a good knowledge of thermal properties of mould materials is needed. Laboratory determination of thermal conductivity of mould mixtures enables a better control over scabbing defects which are a major problem in green sand mould mixtures. A special instrument has been designed for that purpose and it is described in this work.

  9. A novel application of concentrated solar thermal energy in foundries.

    Science.gov (United States)

    Selvaraj, J; Harikesavan, V; Eshwanth, A

    2016-05-01

    Scrap preheating in foundries is a technology that saves melting energy, leading to economic and environmental benefits. The proposed method in this paper utilizes solar thermal energy for preheating scrap, effected through a parabolic trough concentrator that focuses sunlight onto a receiver which carries the metallic scrap. Scraps of various thicknesses were placed on the receiver to study the heat absorption by them. Experimental results revealed the pattern with which heat is gained by the scrap, the efficiency of the process and how it is affected as the scrap gains heat. The inferences from them gave practical guidelines on handling scraps for best possible energy savings. Based on the experiments conducted, preheat of up to 160 °C and a maximum efficiency of 70 % and a minimum efficiency of 40 % could be achieved across the time elapsed and heat gained by the scrap. Calculations show that this technology has the potential to save around 8 % of the energy consumption in foundries. Cumulative benefits are very encouraging: 180.45 million kWh of energy savings and 203,905 t of carbon emissions cut per year across the globe. This research reveals immense scope for this technology to be adopted by foundries throughout the world.

  10. Materials and processing approaches for foundry-compatible transient electronics

    Science.gov (United States)

    Chang, Jan-Kai; Fang, Hui; Bower, Christopher A.; Song, Enming; Yu, Xinge; Rogers, John A.

    2017-07-01

    Foundry-based routes to transient silicon electronic devices have the potential to serve as the manufacturing basis for “green” electronic devices, biodegradable implants, hardware secure data storage systems, and unrecoverable remote devices. This article introduces materials and processing approaches that enable state-of-the-art silicon complementary metal-oxide-semiconductor (CMOS) foundries to be leveraged for high-performance, water-soluble forms of electronics. The key elements are (i) collections of biodegradable electronic materials (e.g., silicon, tungsten, silicon nitride, silicon dioxide) and device architectures that are compatible with manufacturing procedures currently used in the integrated circuit industry, (ii) release schemes and transfer printing methods for integration of multiple ultrathin components formed in this way onto biodegradable polymer substrates, and (iii) planarization and metallization techniques to yield interconnected and fully functional systems. Various CMOS devices and circuit elements created in this fashion and detailed measurements of their electrical characteristics highlight the capabilities. Accelerated dissolution studies in aqueous environments reveal the chemical kinetics associated with the underlying transient behaviors. The results demonstrate the technical feasibility for using foundry-based routes to sophisticated forms of transient electronic devices, with functional capabilities and cost structures that could support diverse applications in the biomedical, military, industrial, and consumer industries.

  11. Statistical and Visualization Data Mining Tools for Foundry Production

    Directory of Open Access Journals (Sweden)

    M. Perzyk

    2007-07-01

    Full Text Available In recent years a rapid development of a new, interdisciplinary knowledge area, called data mining, is observed. Its main task is extracting useful information from previously collected large amount of data. The main possibilities and potential applications of data mining in manufacturing industry are characterized. The main types of data mining techniques are briefly discussed, including statistical, artificial intelligence, data base and visualization tools. The statistical methods and visualization methods are presented in more detail, showing their general possibilities, advantages as well as characteristic examples of applications in foundry production. Results of the author’s research are presented, aimed at validation of selected statistical tools which can be easily and effectively used in manufacturing industry. A performance analysis of ANOVA and contingency tables based methods, dedicated for determination of the most significant process parameters as well as for detection of possible interactions among them, has been made. Several numerical tests have been performed using simulated data sets, with assumed hidden relationships as well some real data, related to the strength of ductile cast iron, collected in a foundry. It is concluded that the statistical methods offer relatively easy and fairly reliable tools for extraction of that type of knowledge about foundry manufacturing processes. However, further research is needed, aimed at explanation of some imperfections of the investigated tools as well assessment of their validity for more complex tasks.

  12. Prevalence of Occupational Asthma and Respiratory Symptoms in Foundry Workers

    Directory of Open Access Journals (Sweden)

    Servet Kayhan

    2013-01-01

    Full Text Available This cross-sectional study was conducted in a foundry factory to assess the prevalence of respiratory symptoms and occupational asthma in foundry workers. Physical examination, spirometric evaluation, chest radiograph, and a questionnaire related to respiratory symptoms were performed. Monitoring of peak expiratory flow rates, spirometric reversibility test, and high-resolution computed tomographies were performed for the participants having respiratory symptoms and/or impaired respiratory function test. A total of 347 participants including 286 workers from production department and 61 subjects who worked in nonproduction departments were enrolled in this study. It is found that phlegm (n: 71, 20.46% and cough (n: 52, 14.98% were the most frequent symptoms. The other symptoms were breathlessness (n: 28, 8.06%, chest tightness (n: 14, 4.03%, and wheezing (n: 7, 2.01% . The prevalence of occupational asthma was found to be more frequent among the subjects who worked in the production department (n: 48, 16.78% than the other persons who worked in the nonproduction department (n: 3, 4.91% by chi-square test (P: 0.001. To prevent hazardous respiratory effects of the foundry production, an early diagnosis of occupational asthma is very important. Cessation of cigarette smoking and using of protective masks during the working time should be encouraged.

  13. Fly-ash poisoning in the surroundings of foundries

    Energy Technology Data Exchange (ETDEWEB)

    Hupka, E

    1955-01-01

    Chronic articular swellings were observed in colts and cattle grazing in the vicinity of two factories. Postmortem findings included an increased synovial content and a detachment of articular cartilage from the underlying bone. Several of the colts also developed roaring due to paralysis of the recurrent nerves. Analysis of fly-ash samples from the two foundries revealed the following: lead, 16.87 percent and 44.79 percent; zinc, 23.41 percent and 5.28 percent; sulfur, 12.53 percent and 8.20 percent; and arsenic, 0.52 percent and 0.22 percent, respectively. Cadmium levels of 2.22 percent were also found in the dust from one of foundries, while cerium (5.00 percent) was detected in the dust from the other foundry. Identical articular lesions were reproduced in two colts receiving dietary rations containing the forge dusts. Manifestations of pharyngoparalysis also appeared, resulting in pneumonia in one case due to pharyngeal dysphagia. Lead poisoning, complicated by other toxic substances, was suggested as the cause. Analyses of several colt livers revealed contents exceeding 0.2 mg/100 g in all cases.

  14. Optimizing the Gating System for Steel Castings

    Directory of Open Access Journals (Sweden)

    Jan Jezierski

    2018-04-01

    Full Text Available The article presents the attempt to optimize a gating system to produce cast steel castings. It is based on John Campbell’s theory and presents the original results of computer modelling of typical and optimized gating systems for cast steel castings. The current state-of-the-art in cast steel casting foundry was compared with several proposals of optimization. The aim was to find a compromise between the best, theoretically proven gating system version, and a version that would be affordable in industrial conditions. The results show that it is possible to achieve a uniform and slow pouring process even for heavy castings to preserve their internal quality.

  15. Laboratory assessment of the influence of the proportion of waste foundry sand on the geotechnical engineering properties of clayey soils

    CSIR Research Space (South Africa)

    Mgangira, Martin B

    2006-01-01

    Full Text Available Soil improvement can be achieved through mechanical stabilisation using industrial byproducts. Clayey soils were blended with waste foundry sand to examine its influence on the geotechnical engineering properties of the soils. The waste foundry sand...

  16. 77 FR 20788 - Foundry Coke Products From the People's Republic of China: Final Results of Expedited Second...

    Science.gov (United States)

    2012-04-06

    ... mm (4 inch) sieve, of a kind used in foundries. The foundry coke products subject to the antidumping... purposes, our written description of the scope of the Order is dispositive. Analysis of Comments Received...

  17. Corrosion resistance of chromium-nickel steel containing rare earths

    International Nuclear Information System (INIS)

    Asatiani, G.N.; Mandzhgaladze, S.N.; Tavadze, L.F.; Chuvatina, S.N.; Saginadze, D.I.

    1983-01-01

    Effect of additional out-of-furnace treatment with complex alloy (foundry alloy) calcite-silicon-magnesium-rare earth metal on corrosion resistance of the 03Kh18N20M3D3C3B steel has been studied. It is shown that introduction of low additions of rare earths improves its corrosion resistance improves its corrosion resistance in agressive media (in 70% - sulfuric acid) in the range of transition from active to passive state. Effect of additional introduction of rare earth metals is not considerable, if potential of steel corrosion is in the range of stable passive state (32% - sulfuric acid). Additional out-of-furnace treatment with complex foundry alloy, containing rare earth metals, provides a possibility to use a steel with a lower content of Cr, Ni, Mo, than in conventional acid-resistant steels in highly agressive media

  18. design and fabrication of a fou fabrication of a foundry sand mixer

    African Journals Online (AJOL)

    eobe

    favourably with the the imported existing one which urably with the the imported existing one which foundry shops will eliminate the use manual effort save the the country of huge save the the country of huge foreign exchange used i foreign exchange used i. Keywords: Keywords:foundry,sand mixer,fabrication,design,bla.

  19. The management of production value stream factors in a foundry

    Directory of Open Access Journals (Sweden)

    S. Borkowski

    2010-01-01

    Full Text Available Connection of two value streams: production and human resources were proposed as a new approach to the production process. To assess the factors of production value streams the elements of the top of the Toyota's house as well as fourth and sixth Toyota's managing principles were used. On the basis of the feedback from respondents –the foundry workers, there can be determined the validity of series of decisive factors' importance that equalizes the work load and requires the standardization.

  20. High Temperature Thermal Properties of Bentonite Foundry Sand

    Directory of Open Access Journals (Sweden)

    Krajewski P.K.

    2015-06-01

    Full Text Available The paper presents results of measuring thermal conductivity and heat capacity of bentonite foundry sand in temperature range ambient - 900­­°C. During the experiments a technical purity Cu plate was cast into the green-sand moulds. Basing on measurements of the mould temperature field during the solidification of the casting, the temperature relationships of the measured properties were evaluated. It was confirmed that water vaporization strongly influences thermal conductivity of the moulding sand in the first period of the mould heating by the poured casting.

  1. Extraction of toxic and valuable metals from foundry sands

    International Nuclear Information System (INIS)

    Vite T, J.

    1996-01-01

    There were extracted valuable metals from foundry sands such as: gold, platinum, silver, cobalt, germanium, nickel and zinc among others, as well as highly toxic metals such as chromium, lead, vanadium and arsenic. The extraction efficiency was up to 100% in some cases. For this reason there were obtained two patents at the United States, patent number 5,356,601, in October 1994, given for the developed process and patent number 5,376,000, in December 1994, obtained for the equipment employed. Therefore, the preliminary parameters for the installation of a pilot plant have also been developed. (Author)

  2. Re-usage of waste foundry sand in high-strength concrete.

    Science.gov (United States)

    Guney, Yucel; Sari, Yasin Dursun; Yalcin, Muhsin; Tuncan, Ahmet; Donmez, Senayi

    2010-01-01

    In this study, the potential re-use of waste foundry sand in high-strength concrete production was investigated. The natural fine sand is replaced with waste foundry sand (0%, 5%, 10%, and 15%). The findings from a series of test program has shown reduction in compressive and tensile strengths, and the elasticity modulus which is directly related to waste foundry inclusion in concrete. Nevertheless the concrete with 10% waste foundry sand exhibits almost similar results to that of the control one. The slump and the workability of the fresh concrete decreases with the increase of the waste foundry sand ratio. Although the freezing and thawing significantly reduces the mechanical and physical properties of the concrete. The obtained results satisfies the acceptable limits set by the American Concrete Institute (ACI). 2010 Elsevier Ltd. All rights reserved.

  3. Total productive maintenance on example of automated foundry lines

    Directory of Open Access Journals (Sweden)

    S. Kukla

    2009-07-01

    Full Text Available Within framework of the presented study one has performed analysis of stoppages in automatic foundry lines operation, and basing on assumptions from complex maintenance system has undertaken himself to develop a service maintenance schedule for machinery installed in the line. Moreover, one has presented general assumptions of TPM system operated in conditions of series and multi-series production of cast iron castings. One has constructed operational database and has elaborated a list of line stoppage causes within a year. One has proposed a possibility of implementation of manufacturing systems modeling and simulating technique in management of production machinery operation in a foundry shop. Within framework of the simulation experiment one has developed schedules of production, schedules of maintenance and has forecasted indices of general productivity of the machinery for a various scenarios of events on example of casting line having in-series structure of operational reliability. In course of the study there was implemented ARENA universal software package to modeling and simulation of the manufacturing systems.

  4. APPLICATION OF ADDITIVELY MANUFACTURED POLYMER COMPOSITE PROTOTYPES IN FOUNDRY

    Directory of Open Access Journals (Sweden)

    Wiesław Kuczko

    2015-05-01

    Full Text Available The paper presents a method, developed by the authors, for manufacturing polymer composites with the matrix manufactured in a layered manner (via 3D printing – Fused Deposition Modeling out of a thermoplastic material. As an example of practical application of this method, functional prototypes are presented, which were used as elements of foundry tooling – patterns for sand molding. In case of manufacturing prototype castings or short series of products, foundries usually cooperate with modeling studios, which produce patterns by conventional, subtractive manufacturing technologies. If patterns have complex shapes, this results in high manufacturing costs and significantly longer time of tooling preparation. The method proposed by the authors allows manufacturing functional prototypes in a short time thanks to utilizing capabilities of additive manufacturing (3D printing technology. Thanks to using two types of materials simultaneously (ABS combined with chemically hardened resins, the produced prototypes are capable of carrying increased loads. Moreover, the method developed by the authors is characterized by manufacturing costs lower than in the basic technology of Fused Deposition Modeling. During the presented studies, the pattern was produced as a polymer composite and it was used to prepare a mold and a set of metal castings.

  5. Excess Foundry Sand Characterization and Experimental Investigation in Controlled Low-Strength Material and Hot-Mixing Asphalt

    Energy Technology Data Exchange (ETDEWEB)

    Pauul J. Tikalsky

    2004-10-31

    This report provides technical data regarding the reuse of excess foundry sand. The report addresses three topics: (1) a statistically sound evaluation of the characterization of foundry sand, (2) a laboratory investigation to qualify excess foundry sand as a major component in controlled low-strength material (CLSM), and (3) the identification of the best methods for using foundry sand as a replacement for natural aggregates for construction purposes, specifically in asphalt paving materials. The survival analysis statistical technique was used to characterize foundry sand over a full spectrum of general chemical parameters, metallic elements, and organic compounds regarding bulk analysis and leachate characterization. Not limited to characterization and environmental impact, foundry sand was evaluated by factor analyses, which contributes to proper selection of factor and maximization of the reuse marketplace for foundry sand. Regarding the integration of foundry sand into CLSM, excavatable CLSM and structural CLSM containing different types of excess foundry sands were investigated through laboratory experiments. Foundry sand was approved to constitute a major component in CLSM. Regarding the integration of foundry sand into asphalt paving materials, the optimum asphalt content was determined for each mixture, as well as the bulk density, maximum density, asphalt absorption, and air voids at N{sub ini}, N{sub des}, and N{sub max}. It was found that foundry sands can be used as an aggregate in hot-mix asphalt production, but each sand should be evaluated individually. Foundry sands tend to lower the strength of mixtures and also may make them more susceptible to moisture damage. Finally, traditional anti-stripping additives may decrease the moisture sensitivity of a mixture containing foundry sand, but not to the level allowed by most highway agencies.

  6. Excess Foundry Sand Characterization and Experimental Investigation in Controlled Low-Strength Material and Hot-Mixing Asphalt

    Energy Technology Data Exchange (ETDEWEB)

    Tikalsky, Paul J. [Pennsylvania State Univ., University Park, PA (United States); Bahia, Hussain U. [Univ. of Wisconsin, Madison, WI (United States); Deng, An [Pennsylvania State Univ., University Park, PA (United States); Snyder, Thomas [Univ. of Wisconsin, Madison, WI (United States)

    2004-10-15

    This report provides technical data regarding the reuse of excess foundry sand. The report addresses three topics: a statistically sound evaluation of the characterization of foundry sand, a laboratory investigation to qualify excess foundry sand as a major component in controlled low-strength material (CLSM), and the identification of the best methods for using foundry sand as a replacement for natural aggregates for construction purposes, specifically in asphalt paving materials. The survival analysis statistical technique was used to characterize foundry sand over a full spectrum of general chemical parameters, metallic elements, and organic compounds regarding bulk analysis and leachate characterization. Not limited to characterization and environmental impact, foundry sand was evaluated by factor analyses, which contributes to proper selection of factor and maximization of the reuse marketplace for foundry sand. Regarding the integration of foundry sand into CLSM, excavatable CLSM and structural CLSM containing different types of excess foundry sands were investigated through laboratory experiments. Foundry sand was approved to constitute a major component in CLSM. Regarding the integration of foundry sand into asphalt paving materials, the optimum asphalt content was determined for each mixture, as well as the bulk density, maximum density, asphalt absorption, and air voids at Nini, Ndes, and Nmax. It was found that foundry sands can be used as an aggregate in hot-mix asphalt production, but each sand should be evaluated individually. Foundry sands tend to lower the strength of mixtures and also may make them more susceptible to moisture damage. Finally, traditional anti-stripping additives may decrease the moisture sensitivity of a mixture containing foundry sand, but not to the level allowed by most highway agencies.

  7. Specificity of SPC Procedures Application in Foundry in Aspect of Data Acquisition and Data Exploration

    Directory of Open Access Journals (Sweden)

    Ignaszak Z.

    2012-12-01

    Full Text Available The paper presents an analysis of SPC (Statistical Process Control procedures usability in foundry engineering. The authors pay particular attention to the processes complexity and necessity of correct preparation of data acquisition procedures. Integration of SPC systems with existing IT solutions in area of aiding and assistance during the manufacturing process is important. For each particular foundry, methodology of selective SPC application needs to prepare for supervision and control of stability of manufacturing conditions, regarding specificity of data in particular “branches” of foundry production (Sands, Pouring, Metallurgy, Quality.

  8. Creation of Defects Catalogue for Nonconforming Product Identification in the Foundry Organization

    Directory of Open Access Journals (Sweden)

    Andrea Sütőová

    2013-12-01

    Full Text Available The paper deals with system of casting defects classification problematics and creation of defects catalogue in the foundry organization. There is described the value of correct defects classification and identification in the literature review and also some tools for defects classification are mentioned. Existing defects classifications and catalogues are often unusable for particular production processes and casting technology. Many foundries therefore create their own defects catalogues. The sample of created catalogue, which classifies and describes defects occuring in the aluminium foundry organization and its benefits are presented in the paper. The created catalogue primarily serves as a visual support for production operators and quality control processes.

  9. Radiometric measurement techniques in metallurgy and foundry technology

    International Nuclear Information System (INIS)

    1990-01-01

    The contributions contain informations concerning the present state and development of radiometric measurement techniques in metallurgy and foundry technology as well as their application to the solution of various problems. The development of isotope techniques is briefly described. Major applications of radiometric equipment in industrial measurement are presented together with the use of isotopes to monitor processes of industrial production. This is followed by a short description of numerous laboratory-scale applications. Another contribution deals with fundamental problems and methods of moisture measurement by neutrons. A complex moisture/density measurement device the practical applicability of which has been tested is described here. Possibilities for clay determination in used-up moulding materials are discussed in a further contribution. The clay content can be determined by real-time radiometric density measurement so that the necessary moisture or addition of fresh sand can be controlled. (orig.) With 20 figs., 9 tabs., 178 refs [de

  10. Laboratories for the 21st Century: Case Studies, Molecular Foundry, Berkeley, California

    Energy Technology Data Exchange (ETDEWEB)

    2010-11-01

    This case study provides information on the Molecular Foundry, which incorporates Labs21 principles in its design and construction. The design includes many of the strategies researched at Lawrence Berkeley Laboratory for energy efficient cleanroom and data centers.

  11. Administrative Record Index for SMA 4 - Former Chemical Plant and SMA 5 - Former Pig Iron Foundry

    Science.gov (United States)

    The Administrative Record Index lists the documents, data and other technical information that the EPA - Region 4 considered in preparing the Statement of Basis for the Former Chemical Plant and the Former Pig Iron Foundry at ERP Compliant Coke.

  12. Implementation KMES Quality system for acquisition and processing data in chosen foundry

    Directory of Open Access Journals (Sweden)

    R. Sika

    2008-08-01

    Full Text Available In the paper, main assumptions, algorithms and functions of author’s KMES Quality system are discussed. Its working version is tested in chosen foundry by near 2 years. This system is applied to enlarge the use of chosen technological data accessible during foundry processes. The data can be introduced by means of keyboard directly in the fields (windows present on the PC screen according to program commands, instead of report-manuscripts containing measured results, or from the automated measurement recording system by direct data import to KMES Quality system. In the paper, a way of technological data acquisition with their further integration into main foundry databases and their processing, with taking into consideration e.g. kind of casting assortment, current time, sequences of measurements, are presented. Also the capabilities of linking KMES Quality system with SAP R/3 system existing in this foundry useful to quality assurance is show.

  13. ESTIMATION OF WORKING CONDITIONS OF FOUNDRY WORKERS BY INFRARED (HEAT RADIATION

    Directory of Open Access Journals (Sweden)

    A. M. Lazarenkov

    2010-01-01

    Full Text Available The description of infrared radiations, their influence on human organism is given. The results of investigation of infrared (heat radiation intensity on the workers in foundries are given.

  14. Barriers to and drivers for energy efficiency in the Swedish foundry industry

    International Nuclear Information System (INIS)

    Rohdin, Patrik; Thollander, Patrik; Solding, Petter

    2007-01-01

    Despite the need for increased industrial energy efficiency, studies indicate that cost-efficient energy conservation measures are not always implemented, explained by the existence of barriers to energy efficiency. This paper investigates the existence of different barriers to and driving forces for the implementation of energy efficiency measures in the energy intensive Swedish foundry industry. The overall results from a questionnaire show that limited access to capital constitutes by far the largest barrier to energy efficiency according to the respondents. A comparison between group-owned and privately owned foundries shows that, except for limited access to capital, they face different high-ranked barriers. While barriers within group owned companies are more related to organizational problems, barriers within private foundries are more related to information problems. This study also found that energy consultants or other actors working with energy issues in foundries are of major importance in overcoming the largest barriers, as the foundries consider them trustworthy. They may thus help the foundries overcome organizational problems such as lack of sub-metering and lack of budget funds by quantifying potential energy efficiency investments. The two, by far, most important drivers were found to be people with real ambition and long-term energy strategies

  15. Identification of Significant Impact of Silicon Foundry Sands Mining on LCIA

    Directory of Open Access Journals (Sweden)

    Jozef Mitterpach

    2015-12-01

    Full Text Available This paper presents a case study based on a LCA (Life Cycle Assessment research program of the silicon foundry sand (SFS due to the large quantity of produced waste foundry sand (WFS. The foundry waste is a high priority sector within the growing European foundry industry. It is necessary to understand the full life cycle of the foundry waste in order to correctly identify magnitude and types of impacts it has on the environment. System boundary includes the processes: mining, modification, packing, storage and transport to foundry. Inventory analysis data were analyzed and finally converted to the functional unit, which has been defined as one ton of SFS. The resulting environmental impact of SFS production in endpoint is: consumption of natural resources 70.9%, ecosystem quality 18.2% and human health 10.9%. The following portions, with respective percentages, have the greatest overall effect on these results: diesel fuel consumption 32.4% and natural gas consumption 28.7%, electricity usage 17.2%, transport 12.2%, devastation caused by the SFS 5.35% and oil (engine, gear and hydraulic consumption 4.14%. The highest contributor to the diesel fuel consumption is the SFS exploitation. The overall effect of desiccation was 35.8% and was caused by high consumption of resources and electricity.

  16. United Kingdom's experience

    International Nuclear Information System (INIS)

    Drummond, S.M.

    1994-01-01

    This is a presentation of the United Kingdom's experience with power transmission open access. The topics of the presentation include the objectives of changing, commercial arrangements and economic drivers, long term effects, the effects of moving to a more competitive environment, and factors affecting open access such as political climate and market regulation

  17. Modelling and Optimization of Organization of Workplaces in a Foundry

    Directory of Open Access Journals (Sweden)

    Kukla S.

    2016-09-01

    Full Text Available The paper presents a practical example of improvement of foundry production systems in terms of post-finishing of nodular iron castings produced in the conditions of bulk production for automotive industry. The attention was paid to high labour-intensive efforts, which are difficult to be subjected to mechanization and automation. The times of actions related to grinding processing of castings in three grinding positions connected with a belt conveyor were estimated with the use of a time study method. A bottleneck as well as limiting factors were specified in a system. A number of improvements were proposed, aimed at improving work organization on the castings post-finishing line. An analysis of work ergonomics at the workplace was made in order to eliminate unnecessary and onerous for the employee actions. A model of production system using the Arena software, on which a simulation experiment was conducted, was drawn up in order to visualize the analysed phenomena. The effects of the project were shown on graphs comparing times, costs, work ergonomics and overall efficiency of production equipment indicator.

  18. Biopolimers – structure, properties and applicability in the foundry industry

    Directory of Open Access Journals (Sweden)

    B. Grabowska

    2008-04-01

    Full Text Available A review of literature data concerning physicochemical properties and possibilities of practical utilisation of the most important natural biopolymers (proteins, celluloses, starch, chitozan are presented in the paper. Biopolymers being renewable natural polymers characterised by several required physicochemical properties (adhesivity, activity, no toxicity, biodegradability constitute more and more interesting processing raw material for various industrial utilisations including environment friendly binding agents for moulding sands. Protein and starch compositions are used as binding agents for moulding and core sands in the foundry industry. Preliminary tests – performed within own research - of modification and utilisation of biopolymers as binding agents for moulding sands are promising from many aspects: technological (adequate properties of moulding sands, ecological (no toxicity, biodegradability and economic (low price. Starch from the polysaccharide group seems to be especially interesting since it is abundant, easily obtainable, biodegradable and the cheapest polymer. At its actual low price and the possibility of using agricultural wastes in the production, problem of utilising starch in many industry branches can become significant, especially in Poland.

  19. Sustainability innovation foundry - FY13: Merging research and operations

    Energy Technology Data Exchange (ETDEWEB)

    Mizner, Jack Harry [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Passell, Howard David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Keller, Elizabeth James Kistin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gordon, Margaret Ellen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); McNeish, Jerry A. [Sandia National Laboratories, Livermore, CA (United States); Sullivan, Kristina [Sandia National Laboratories, Livermore, CA (United States)

    2013-12-01

    Sustainability is a critical national security issue for the U.S. and other nations. Sandia National Laboratories (SNL) is already a global leader in sustainability science and technology (SS&T) as documented in this report. This report documents the ongoing work conducted this year as part of the Sustainability Innovation Foundry (SIF). The efforts of the SIF support Sandia's national and international security missions related to sustainability and resilience revolving around energy use, water use, and materials, both on site at Sandia and externally. The SIF leverages existing Sandia research and development (R&D) in sustainability science and technology to support new solutions to complex problems. The SIF also builds on existing Sandia initiatives to support transformation of Sandia into a fully sustainable entity in terms of materials, energy, and water use. In the long term, the SIF will demonstrate the efficacy of sustainability technology developed at Sandia through prototyping and test bed approaches and will provide a common platform for support of solutions to the complex problems surrounding sustainability. Highlights from this year include the Sustainability Idea Challenge, improvements in facilities energy use, lectures and presentations from relevant experts in sustainability [Dr. Barry Hughes, University of Denver], and significant development of the Institutional Transformation (IX) modeling tools to support evaluation of proposed modifications to the SNL infrastructure to realize energy savings.

  20. Contaminated Mexican steel incident

    International Nuclear Information System (INIS)

    1985-01-01

    This report documents the circumstances contributing to the inadvertent melting of cobalt 60 (Co-60) contaminated scrap metal in two Mexican steel foundries and the subsequent distribution of contaminated steel products into the United States. The report addresses mainly those actions taken by US Federal and state agencies to protect the US population from radiation risks associated with the incident. Mexico had much more serious radiation exposure and contamination problems to manage. The United States Government maintained a standing offer to provide technical and medical assistance to the Mexican Government. The report covers the tracing of the source to its origin, response actions to recover radioactive steel in the United States, and return of the contaminated materials to Mexico. The incident resulted in significant radiation exposures within Mexico, but no known significant exposure within the United States. Response to the incident required the combined efforts of the Nuclear Regulatory Commission (NRC), Department of Energy, Department of Transportation, Department of State, and US Customs Service (Department of Treasury) personnel at the Federal level and representatives of all 50 State Radiation Control Programs and, in some instances, local and county government personnel. The response also required a diplomatic interface with the Mexican Government and cooperation of numerous commercial establishments and members of the general public. The report describes the factual information associated with the event and may serve as information for subsequent recommendations and actions by the NRC. 8 figures

  1. Energy efficiency opportunities in the production process of cast iron foundries: An experience in Italy

    International Nuclear Information System (INIS)

    Lazzarin, Renato M.; Noro, Marco

    2015-01-01

    Foundry sector is one of the most energy intensive in industry. Energy audits performed in 5 Italian cast iron foundries allowed to identify energy utilization in the various processes that from the melting of the iron arrive at the finishing of the casting. Main equipment was surveyed, evaluating the influence on the overall energy consumption, producing a detailed analysis of energy use per department and energy performance indexes. A separate study was carried out for foundries with induction furnaces and cold or hot blast cupolas. Possibilities of heat recovery was identified particularly in combustion air preheating, but also for building heating or to power direct cycles to produce electricity. Better insulation and new insulating materials can improve the efficiency and the quality of the processes. Suggestions are supplied in the various foundry departments for energy saving. Possible energy saving actions on the service plants will be dealt with in a separate paper. - Highlights: • The Authors performed energy audits in 5 Italian cast iron foundries. • Main equipment was surveyed, evaluating the influence on the overall energy consumption. • An analysis of energy use per department and energy performance indexes was performed. • Possibilities of heat recovery were identified in combustion air preheating and for building heating. • Better and new insulating materials were analyzed to improve the efficiency and process quality.

  2. Combustion strategy : United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Greenhalgh, D. [Heriot-Watt Univ., Edingburgh, Scotland (United Kingdom). School of Engineering and Physical Sciences

    2009-07-01

    The United Kingdom's combustion strategy was briefly presented. Government funding sources for universities were listed. The United Kingdom Research Councils that were listed included the Arts and Humanities Research Council (AHRC) and the Biotechnology and Biological Sciences Research Council (BBSRC); the Engineering and Physical Sciences Research Council (EPSRC); the Economic and Social Research Council; the Medical Research Council; the Natural Environment Research Council; and the Science and Technology Facilities Council. The EPSRC supported 65 grants worth 30.5 million pounds. The combustion industry was noted to be dominated by three main players of which one was by far the largest. The 3 key players were Rolls-Royce; Jaguar Land Rover; and Doosan Babcock. Industry and government involvement was also discussed for the BIS Technology Strategy Board, strategy technology areas, and strategy application areas.

  3. Let your kingdom come

    Directory of Open Access Journals (Sweden)

    L.F. Schulze

    2001-08-01

    Full Text Available As an introduction to the general theme “The kingdom of God”, this article presents an overview of the second petition of the Lord’s Prayer. This is done under the following headings: the setting, the aspects, and the guidelines of the petition. The setting shows the very close relation among the first three petitions as pertaining to God’s cause, and the priority which his kingship should have in our prayers. In turning to God in our prayers, we turn away from ourselves. Thus prayer is part of our sanctification. The aspects treated in this article are, firstly, that the second petition is a prayer, implying our helplessness and destitution; secondly, that it concerns God’s kingdom, not ours, thereby undercutting every form of modernism, Social Gospel, political theology, and progressive ethical ‘goodness’ of man; thirdly, it is a petition that the kingdom may come, which happens mysteriously, in God’s time, in our history, and according to Scriptures. In the guidelines it is argued that, in order to live responsibly as Christians, we must know our time, ourselves, and the immutable nature of prophecy.

  4. Simulation by the method of inverse cumulative distribution function applied in optimising of foundry plant production

    Directory of Open Access Journals (Sweden)

    J. Szymszal

    2009-01-01

    Full Text Available The study discusses application of computer simulation based on the method of inverse cumulative distribution function. The simulationrefers to an elementary static case, which can also be solved by physical experiment, consisting mainly in observations of foundryproduction in a selected foundry plant. For the simulation and forecasting of foundry production quality in selected cast iron grade, arandom number generator of Excel calculation sheet was chosen. Very wide potentials of this type of simulation when applied to theevaluation of foundry production quality were demonstrated, using a number generator of even distribution for generation of a variable ofan arbitrary distribution, especially of a preset empirical distribution, without any need of adjusting to this variable the smooth theoreticaldistributions.

  5. Drying of water based foundry coatings: Innovative test, process design and optimization methods

    DEFF Research Database (Denmark)

    Di Muoio, Giovanni Luca; Johansen, Bjørn Budolph

    on real industrial cases. These tools have been developed in order to simulate and optimize the drying process and reduce drying time and power consumption as well as production process design time and cost of expensive drying equipment. Results show that test methods from other industries can be used...... capacity goals there is a need to understand how to design, control and optimize drying processes. The main focus of this project was on the critical parameters and properties to be controlled in production in order to achieve a stable and predictable drying process. We propose for each of these parameters...... of Denmark with the overall aim to optimize the drying process of water based foundry coatings. Drying of foundry coatings is a relatively new process in the foundry industry that followed the introduction of water as a solvent. In order to avoid moisture related quality problems and reach production...

  6. Comparison of Energy Consumption in the Classical (PID and Fuzzy Control of Foundry Resistance Furnace

    Directory of Open Access Journals (Sweden)

    Ziółkowskia E.

    2012-09-01

    Full Text Available Foundry resistance furnaces are thermal devices with a relatively large time delay in their response to a change in power parameters. Commonly used in automation classical PID controllers do not meet the requirements of high-quality control. Developed in recent years, fuzzy control theory is increasingly being used in various branches of economy and industry. Fuzzy controllers allow to introduce new developments in control systems of foundry furnaces as well. Correctly selected fuzzy controller can significantly reduce energy consumption in a controlled thermal process of heating equipment. The article presents a comparison of energy consumption by control system of foundry resistance furnace, equipped with either a PID controller or fuzzy controller optimally chosen.

  7. Prevention of occupational injuries: Evidence for effective good practices in foundries.

    Science.gov (United States)

    Porru, Stefano; Calza, Stefano; Arici, Cecilia

    2017-02-01

    Occupational injuries are a relevant research and practical issue. However, intervention studies evaluating the effectiveness of workplace injury prevention programs are seldom performed. The effectiveness of a multifaceted intervention aimed at reducing occupational injury rates (incidence/employment-based=IR, frequency/hours-based=FR, severity=SR) was evaluated between 2008 and 2013 in 29 Italian foundries (22 ferrous; 7 non-ferrous; 3,460 male blue collar workers/year) of varying sizes. Each foundry established an internal multidisciplinary prevention team for risk assessment, monitoring and prevention of occupational injuries, involving employers, occupational physicians, safety personnel, workers' representatives, supervisors. Targets of intervention were workers, equipment, organization, workplace, job tasks. An interrupted time series (ITS) design was applied. 4,604 occupational injuries and 83,156 lost workdays were registered between 2003 and 2013. Statistical analysis showed, after intervention, a reduction of all injury rates (-26% IR, -15% FR, -18% SR) in ferrous foundries and of SR (-4%) in non-ferrous foundries. A significant (p=0.021) 'step-effect' was shown for IR in ferrous foundries, independent of secular trends (pgood external validity; promotion of effective good practices. Main limitations were the non-randomized nature and a medium length post-intervention period. In conclusion, a multifaceted, pragmatic and accountable intervention is effective in reducing the burden of occupational injuries in small-, medium- and large-sized foundries. Practical Applications: The study poses the basis for feasible good practice guidelines to be implemented to prevent occupational injuries, by means of sector-specific numerical benchmarks, with potentially relevant impacts on workers, companies, occupational health professionals and society at large. Copyright © 2016 National Safety Council and Elsevier Ltd. All rights reserved.

  8. Optimization of casting defects analysis with supply chain in cast iron foundry process

    Directory of Open Access Journals (Sweden)

    C. Narayanaswamy

    2016-10-01

    Full Text Available Some of the foundries are in need of meeting production targets and due to the urgency they ignore the rejections. The objective of this paper is to analyze the various defects, [1] from molding process in a cast iron foundry. The Failure Mode Effects Analysis (FMEA in quality control [2-6] with suitable supply chain for mold making process considering rejection rates are identified and analyzed in terms of Risk Priority Number (RPN to prioritize the attention for each of the problem. The optimum levels of selected parameters [7] are obtained in this analysis.

  9. Using sol-gel component as additive to foundry coatings to improve casting quality

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Poulsen, T.; Gravesen, B.

    2012-01-01

    The improvement of foundry coatings to enhance performance is important. This paper investigates the effect of using sol‐gel component as an additive to foundry coatings applied on chemically bonded sand cores. Three parameters at three levels each were investigated using Taguchi experimental...... was evaluated. The results show that the surface quality of castings obtained by adding the sol‐gel component to the coatings for cold box cores has no significant difference from castings produced with coatings without sol‐gel component. On the other hand, the addition of the sol‐gel component in coatings...

  10. The study of heavy metals leaching from waste foundry sands using a one-step extraction

    Science.gov (United States)

    Bożym, Marta

    2017-10-01

    There are a number of leaching test which are used to evaluate the effect of foundry waste disposal on the environment (TCLP, SPLP, ASTM at al.). Because the spent foundry sand are usually deposited at the ground level and they have a similar structure to the soil, survey mobility of metals using the same methods seems appropriate. One-step extraction allows for the evaluation of the mobility and bioavailability of metals in soil and waste. Waste foundry sands have been successfully used as a component in manufactured soils in U.S., but concern over metal contamination must be eliminated before considering this direction of use. The study evaluated the leaching of heavy metals (Cd, Pb, Cu, Zn, Cr, Ni) from deposited waste foundry sands. The overall, as well as heavy metals were extracted by different type of extractants: H2O, CH3COOH, HCl, EDTA, MgCl2 and NaCOOH. These extractants are most commonly used to study the mobility and bioavailability of metals in soil and waste. In the present study applicable standards and methodology described in the literature in analysis were used. The results allowed to evaluate the bioavailability of metals leached from those wastes.

  11. Risk assessment of chemicals in foundries: The International Chemical Toolkit pilot-project

    International Nuclear Information System (INIS)

    Ribeiro, Marcela G.; Filho, Walter R.P.

    2006-01-01

    In Brazil, problems regarding protection from hazardous substances in small-sized enterprises are similar to those observed in many other countries. Looking for a simple tool to assess and control such exposures, FUNDACENTRO has started in 2005 a pilot-project to implement the International Chemical Control Toolkit. During the series of visits to foundries, it was observed that although many changes have occurred in foundry technology, occupational exposures to silica dust and metal fumes continue to occur, due to a lack of perception of occupational exposure in the work environment. After introducing the Chemical Toolkit concept to the foundry work group, it was possible to show that the activities undertaken to improve the management of chemicals, according to its concept, will support companies in fulfilling government legislations related to chemical management, occupational health and safety, and environmental impact. In the following meetings, the foundry work group and FUNDACENTRO research team will identify 'inadequate work situations'. Based on the Chemical Toolkit, improvement measures will be proposed. Afterwards, a survey will verify the efficency of those measures in the control of hazards and consequently on the management of chemicals. This step is now in course

  12. Methodology supporting production control in a foundry applying modern DISAMATIC molding line

    Directory of Open Access Journals (Sweden)

    Sika Robert

    2017-01-01

    Full Text Available The paper presents methodology of production control using statistical methods in foundry conditions, using the automatic DISAMATIC molding line. The authors were inspired by many years of experience in implementing IT tools for foundries. The authors noticed that there is a lack of basic IT tools dedicated to specific casting processes, that would greatly facilitate their oversight and thus improve the quality of manufactured products. More and more systems are installed in the ERP or CAx area, but they integrate processes only partially, mainly in the area of technology design and business management from finance and control. Monitoring of foundry processes can generate a large amount of process-related data. This is particularly noticeable in automated processes. An example is the modern DISAMATIC molding line, which integrates several casting processes, such as mold preparation, assembly, pouring or shake out. The authors proposed a methodology that supports the control of the above-mentioned foundry processes using statistical methods. Such an approach can be successfully used, for example, during periodic external audits. The mentioned methodology in the innovative DISAM-ProdC computer tool was implemented.

  13. The study of heavy metals leaching from waste foundry sands using a one-step extraction

    Directory of Open Access Journals (Sweden)

    Bożym Marta

    2017-01-01

    Full Text Available There are a number of leaching test which are used to evaluate the effect of foundry waste disposal on the environment (TCLP, SPLP, ASTM at al.. Because the spent foundry sand are usually deposited at the ground level and they have a similar structure to the soil, survey mobility of metals using the same methods seems appropriate. One-step extraction allows for the evaluation of the mobility and bioavailability of metals in soil and waste. Waste foundry sands have been successfully used as a component in manufactured soils in U.S., but concern over metal contamination must be eliminated before considering this direction of use. The study evaluated the leaching of heavy metals (Cd, Pb, Cu, Zn, Cr, Ni from deposited waste foundry sands. The overall, as well as heavy metals were extracted by different type of extractants: H2O, CH3COOH, HCl, EDTA, MgCl2 and NaCOOH. These extractants are most commonly used to study the mobility and bioavailability of metals in soil and waste. In the present study applicable standards and methodology described in the literature in analysis were used. The results allowed to evaluate the bioavailability of metals leached from those wastes.

  14. Research and application of enterprise resource planning system for foundry enterprises

    Directory of Open Access Journals (Sweden)

    Zhou Jianxin

    2013-01-01

    Full Text Available PPDB issues - four aspects of current management issues of foundry enterprises are discussed in this paper, including Production Management, Process Control, Duration Monitoring and Business Intelligence Data Analysis. Also a whole Enterprise Resource Planning (ERP solution for foundry enterprises is proposed. The solution contains many models, four of which are used to solve the PPDB issues. These are called SPDB models, which separately are the Single-piece management model (based on casting lifecycle, Process management model (based on task-driven technology, Duration monitoring model (based on surplus period, and Business intelligence data analysis model (based on data mining. An ERP system for foundry enterprises, named HZERP, was researched and developed, and applied to a sand casting company of single piece and small batch production. Qualitatively and quantitatively comparing the application effect before and after implementing the HZERP system, the result demonstrated that the foundry ERP system based on the SPDB models can help metal casting enterprises achieve the single-piece management, better regulate the production processes, improve production and delivery management, shorten the production cycle, reduce costs, and speed up the capital turnover to a large extent.

  15. UNITED KINGDOM: under pressure

    International Nuclear Information System (INIS)

    Anon.

    1994-01-01

    While attempting bravely to sustain the legacy left by J.J. Thomson, Rutherford, Chadwick, Cockcroft, Blackett, Dirac and others earlier this century, the United Kingdom, one of the major contributors to CERN, has suffered in recent years from an erosion of the international purchasing power of the pound sterling. At the same time, the national scientific community has squabbled over the apportionment of the research cake. In recent years, the CERN budget has remained constant in real terms, but the pound has drifted steadily down. In 1984 one pound bought 3.15 Swiss francs, now it gets just over 2. The hypersensitivity which left calculations at the mercy of exchange rate hiccups was cushioned in 1988 by a new method of calculating national CERN contributions, introduced by Chris Llewellyn Smith, now the Laboratory's Director General, using less sensitive input data

  16. United Kingdom national report

    International Nuclear Information System (INIS)

    Tomkins, B.

    1998-01-01

    Report of the United Kingdom deals with life extension granted to Calder Hall and Chapelcross reactors for further 10 years operation. The two well recognised life-limiting features of Magnox type reactors are graphite core ageing and materials properties of the reactor pressure circuit components. These features have been scrutinised particularly closely and the conclusion has been reached that there are no safety factors which will necessarily limit the plant life to less than 50 years. Two other life-limiting factors are hear exchanger tubes and the heat exchanger tube failures internal to boiler shells and the integrity of the main engineering structures of the plant. It was concluded that appropriate routine ageing monitoring programs are in place in respect to these features to support continuing operation beyond 40 years

  17. A new low-cost method of reclaiming mixed foundry waste sand based on wet-thermal composite reclamation

    OpenAIRE

    Fan Zitian; Liu Fuchu; Long Wei

    2014-01-01

    A lot of mixed clay-resin waste sand from large-scale iron foundries is discharged every day; so mixed waste sand reclamation in low cost and high quality has a great realistic significance. In the study to investigate the possibility of reusing two types of waste foundry sands, resin bonded sand and clay bonded sand which came from a Chinese casting factory, a new low-cost reclamation method of the mixed foundry waste sand based on the wet-thermal composite reclamation was proposed. The wast...

  18. Design process optimization, virtual prototyping of manufacturing, and foundry-portable DFM (Invited Paper)

    Science.gov (United States)

    Hogan, James; Progler, Christopher; Chatila, Ahmad; Bruggeman, Bert; Heins, Mitchell; Pack, Robert; Boksha, Victor

    2005-05-01

    We consider modern design for manufacturing (DFM) as a manifestation of IC industry re-integration and intensive cost management dynamics. In that regard DFM is somewhat different from so-called design for yield (DFY) which essentially focuses on productivity (yield) management (that is not to say that DFM and DFY do not have significant overlaps and interactions). We clearly see the shaping of a new "full-chip DFM" infrastructure on the background of the "back to basics" design-manufacturing re-integration dynamics. In the presented work we are focusing on required DFM-efficiencies in a "foundry-fabless" link. Concepts of "virtual prototyping of manufacturing", "design process optimization", and "foundry-portable DFM" models are explored. Both senior management of the industry and leading design groups finally realize the need for a radical change of design styles. Some of the DFM super-goals are to isolate designers from process details and to make designs foundry portable. It requires qualification of designs at different foundries. In their turn, foundries specified and are implementing a set of DFM rules: "action-required", "recommended", and "guidelines" while asking designers to provide netlist and testing information. Also, we observe strong signs of innovation coming back to the mask industry. Powerful solutions are emerging and shaping up toward mask-centered IP as a business. While it seems that pure-play foundries have found their place for now in the "IDM+" model (supporting manufacturing capacity of IDMs) it is not obvious how sustainable the model is. Wafer as a production unit is not sufficient anymore; foundries are being asked by large customers to price products in terms of good die. It brings back the notion of the old ASIC business model where the foundry is responsible for dealing with both random and systematic yield issues for a given design. One scenario of future development would be that some of the leading foundries might eventually

  19. [Comparison of color reappearance between metal-ceram restoration and foundry-ceram restoration using crystaleye spectrophotometer].

    Science.gov (United States)

    Shi, Tao; Zhang, Ning; Kong, Fan-wen; Zhan, De-song

    2010-10-01

    To study the color reappearance effect of metal-ceram restoration and foundry-ceram restoration using Crystaleye spectrophotometer. 58 metal-ceram restorations and 58 foundry-ceram restorations according to the result of the Crystaleye spectrophotometer were made respectively. The deltaE between restorations and natural teeth as referenced were analyzed. And satisfaction of dentists and patients were evaluated. The deltaE between metal-ceram restorations and natural teeth was 7.13 +/- 0.74. The deltaE between foundry-ceram restorations and teeth was 1.47 +/- 0.84. There were statistical differences between the deltaE (P spectrophotometer can provide accurate reference for foundry-ceram restoration, but for metal-ceram restoration it is not accurate.

  20. United Kingdom position paper

    International Nuclear Information System (INIS)

    1983-01-01

    In any system employing liquid sodium as a coolant, large heat transfer coefficients exist between the metal structure containing the coolant, and the coolant itself. Any rapidly varying temperatures, either space wise or time wise, in the sodium are readily transmitted to the surrounding metal structure, resulting in the generation of appreciable thermal stresses within these structures. In particular, the phenomenon of thermal stratification in the sodium coolant has the potential to induce unacceptable thermal stresses throughout the system. With respect to the present U.K. fast reactor design, a large programme of work in connection with the thermal hydraulic aspects of the plant is in hand. This programme is being undertaken as a joint effort by the National Nuclear Corporation, the United Kingdom Atomic Energy Authority, and the Central Electricity Generating Board. Work is in progress both to identify the areas of the system that will be susceptible to, and to ensure that the design is capable of successfully withstanding any thermal stratification effects. The production of stratification phenomena depends both upon the design and the operation of the reactor system. These are briefly described below. Areas where thermal stratification effects exist are then identified and the programme of work associated with each area is outlined

  1. The United Kingdom

    International Nuclear Information System (INIS)

    Jones, P.M.S.

    1987-01-01

    The history of nuclear development in the United Kingdom is traced, together with the factors (eg electricity demand, fossil fuel prices, political policy) that have influenced policy choices. Many of the research establishments and the fissile material production plants were established in the late 1940s. In these early years the civil and military development programmes were not separate. The initial growth period was in the 1950s when the plan was to build twelve reactors in three groups of four over ten years. The first were to be Magnox type reactors. This was trebled in 1957 and the advanced gas cooled reactor was developed. The Windscale fire in 1957 affected confidence in the nuclear programme. However, five AGR twin-reactor stations were ordered in 1964. These ran into construction problems and delay and it was not until 1980 that more new units were contemplated. The plan then was to build a pressurized water reactor at Sizewell-B. A delay to allow for the public inquiry put back the start of this until 1987 with commissioning planned for 1994. A list of the UK nuclear power stations is given and their operating performance discussed. The present situation and future prospects for nuclear power are reviewed. (U.K.)

  2. Biobank Report: United Kingdom.

    Science.gov (United States)

    Kaye, Jane; Bell, Jessica; Briceno, Linda; Mitchell, Colin

    2016-03-01

    The United Kingdom is a leader in genomics research, and the presence of numerous types of biobanks and the linking of health data and research within the UK evidences the importance of biobank-based research in the UK. There is no biobank-specific law in the UK and research on biobank materials is governed by a confusing set of statutory law, common law, regulations, and guidance documents. Several layers of applicable law, from European to local, further complicate an understanding of privacy protections. Finally, biobanks frequently contain data in addition to the samples; the legal framework in the UK generally differentiates between data and samples and the form of the data affects the applicability of legal provisions. Biobanks must be licensed by the Human Tissue Authority; certain projects must be reviewed by Research Ethics Committees, and all projects are encouraged to be reviewed by them. Data Access Committees in biobanks are also common in the UK. While this confusing array of legal provisions leaves privacy protections in biobanking somewhat unclear, changes at the EU level may contribute to harmonization of approaches to privacy. © 2016 American Society of Law, Medicine & Ethics.

  3. The United Kingdom

    International Nuclear Information System (INIS)

    Croft, S.; Williams, P.

    1991-01-01

    The possession of nuclear weapons by the United Kingdom has long been a controversial issue in British politics, and among historians and strategists. Part of the controversy has revolved around questions of motivation. Why did the British Government under Prime Minister Clement Attlee develop nuclear weapons? Why have successive British governments maintained and, in fact, modernized the national nuclear force? This paper reports that a frequent response to these questions is to place the issue of the acquisition of nuclear weapons by the UK into a post-colonial context. In the nineteenth and early twentieth centuries, Britain was a great power with global assets and commitments. After the Empire was reduced in size and importance, however, and eventually swept away, Britain could not longer claim to be a superpower in any modern sense. Nevertheless, it is suggested, British policy makers had developed a foreign policy based upon certain assumptions about Britain's position and power and they were reluctant to relinquish these assumptions. Furthermore, it is contended, the decision to develop nuclear weapons was taken to reinforce what were the pretensions of a medium power, and the continued obsession of successive British governments with nuclear weapons provides evidence that Britain has still not come to terms with its reduced role and limited influence. In short, the British infatuation with nuclear weapons over the past 40 years is best explained in terms of concerns about status

  4. Applications of the systems theory to the designing of the sand preparation sub-system in foundry plants

    Directory of Open Access Journals (Sweden)

    R. Wrona

    2009-07-01

    Full Text Available This study provides the basic principles for designing the functional structure of manufacturing systems and their components. The analysis of functional values is applied to create the technological and manufacturing model underlying the design of the foundry equipment with machine units and materials handling systems. Quoted examples illustrate the approved procedure to be applied to control the sand preparation process in a foundry.

  5. Lysozymes in the animal kingdom

    Indian Academy of Sciences (India)

    In the animal kingdom, three major distinct lysozyme types have been ... reveals that c-type lysozymes are predominantly present in the phylum of the Chordata and in different classes of the Arthropoda. ... Journal of Biosciences | News ...

  6. Renewable energies in United Kingdom

    International Nuclear Information System (INIS)

    Baize, T.

    1993-01-01

    An evaluation of research and development policy in United Kingdom on renewable energy sources is presented with economical studies (short or long term profitability), engaged programs and electric production. (A.B.). refs. tabs

  7. Investigation into the Heat of Hydration and Alkali Silica Reactivity of Sustainable Ultrahigh Strength Concrete with Foundry Sand

    Directory of Open Access Journals (Sweden)

    Federico Aguayo

    2017-01-01

    Full Text Available This study presents the hydration reactivity and alkali silica reaction (ASR of ultrahigh strength concrete (UHSC that has been made more sustainable by using spent foundry sand. Spent foundry sand not only is sustainable but has supplementary cementitious material (SCM characteristics. Two series of UHSC mixtures were prepared using a nonreactive and reactive sand (in terms of ASR to investigate both the impact of a more reactive aggregate and the use of spent foundry sand. Conduction calorimetry was used to monitor the heat of hydration maintained under isothermal conditions, while ASR was investigated using the accelerated mortar bar test (AMBT. Additionally, the compressive strengths were measured for both series of mixtures at 7, 14, and 28 days to confirm high strength requirements. The compressive strengths ranged from 85 MPa (12,345 psi to 181.78 MPa (26,365 psi. This result demonstrates that a UHSC mixture was produced. The calorimetry results revealed a slight acceleration in the heat of hydration flow curve compared to the control from both aggregates indicating increased hydration reactivity from the addition of foundry waste. The combination of foundry sand and reactive sand was found to increase ASR reactivity with increasing additions of foundry sand up to 30% replacement.

  8. Reuse of waste foundry sand through interaction with sodium silicate binder

    International Nuclear Information System (INIS)

    Souza, J.C.; Chinelatto, A.S.A.; Chinelatto, A.L.; Oliveira, I.L.

    2012-01-01

    Green sand molds are used in metal casting process. However, after heating, activated bentonite present in green sand lose the binding properties, and part of the foundry sand has to be discarded from the process. The ABNT NBR 15.984/2011 establishes the management of waste foundry sand (WFS) avoiding disposal in landfills. The objective of this work was to investigate the possibility of reusing the WFS from the study of their interaction with sodium silicate binder. Studies with silica sand and new green sand was performed to compare the results obtained with the WFS. The characterizations of the samples were performed by measures the compressive strength, X-ray diffraction, optical microscopy and scanning electron microscopy. The results showed that there is interaction of the sodium silicate with the WFS as well as with the silica sand and green sand. (author)

  9. EVALUATION OF THE BENTONITE CONTENT IN SPENT FOUNDRY SANDS AS A FUNCTION OF HYDRAULIC CONDUCTIVITY COEFFICIENT

    Directory of Open Access Journals (Sweden)

    Schirlene Chegatti

    2013-06-01

    Full Text Available This study evaluates the relationship of the bentonite content and hydraulic conductivity coefficient (k of waste foundry sands in tests of hydraulic conductivity in a flexible wall permeameter. The test samples had concentrations of activated sodium bentonite and natural sodium bentonite between 4% and 15%. It was also analyzed chemically the liquid leachate (aluminum, barium, chromium, cadmium, lead, phenols, iron, fluoride, and manganese, following de standard tests of Standard Methods 3111 B e D for the determination of this components in liquid samples. The experiments were supplemented with cation exchange capacity analysis. The results indicate that the values of are is related to the content of bentonite in waste foundry sand and the percolation from this waste disposal.

  10. Study on Type C Coal Fly ash as an Additive to Molding Sand for Steel Casting

    Science.gov (United States)

    Palaniappan, Jayanthi

    2017-04-01

    Study of physio-chemical properties studies such as granulometric analysis, moisture, X ray fluorescence etc. were performed with Type C coal—combustion fly ash to investigate their potential as a distinct option for molding sand in foundry, thereby reducing the dependency on latter. Technological properties study such as compressive strength, tensile strength, permeability and compaction of various compositions of fly ash molding sand (10, 20 and 30 % fly ash substitute to chemically bonded sand) were performed and compared with silica molding sand. Steel casting production using this fly ash molding sand was done and the casting surface finish and typical casting parameters were assessed. It was noted that a good quality steel casting could be produced using type C fly ash molding sand, which effectively replaced 20 % of traditional molding sand and binders thereby providing greater financial profits to the foundry and an effective way of fly ash utilization (waste management).

  11. SYNBIOCHEM Synthetic Biology Research Centre, Manchester – A UK foundry for fine and speciality chemicals production

    Directory of Open Access Journals (Sweden)

    Le Feuvre RA

    2016-12-01

    Full Text Available The UK Synthetic Biology Research Centre, SYNBIOCHEM, hosted by the Manchester Institute of Biotechnology at the University of Manchester is delivering innovative technology platforms to facilitate the predictable engineering of microbial bio-factories for fine and speciality chemicals production. We provide an overview of our foundry activities that are being applied to grand challenge projects to deliver innovation in bio-based chemicals production for industrial biotechnology.

  12. Moisture diffusion coefficients determination of furan bonded sands and water based foundry coatings

    DEFF Research Database (Denmark)

    Di Muoio, Giovanni Luca; Tiedje, Niels Skat

    2016-01-01

    Moisture content in furan bonded sand and water based coatings can be one of the main causes for gas related defects in large cast iron parts. Moisture diffusion coefficients for these materials are needed to precisely predict the possible moisture levels in foundry moulds. In this study, we first...... provide an example on how it is possible to apply this knowledge to estimate moisture variation in a sand mould during production....

  13. AN ANALYSIS OF THE DIFFERENTIATION STRATEGIES OF RURAL FOUNDRIES IN THE BEGINNING OF THE 20TH CENTURY IN THE PROVINCE OF QUEBEC

    Directory of Open Access Journals (Sweden)

    Lisa Baillargeon

    2009-01-01

    Full Text Available The business model and strategic position of Quebec's rural foundries at the beginning of the 20th century is virtually unknown. Inferences have been made based on pictorial and oral data sources. This data reveals that successful rural foundries were, in essence, confined to producing and selling agricultural tools to local farmers on an as-needed basis, because large urban foundries were already mass-producing domestic and industrial objects. In contrast, use of detailed accounting records and advertising publications of three rural foundries over the 1900 to 1914 period provides a clearer picture of the production and of the clientele of those rural foundries. Analysis of these sources suggests that the strategic business model of rural foundries was much more elaborate than the existing literature posits. Rural owner-managers of the early 20th century were sophisticated strategists, marketers, and operators.

  14. ELABORATION OF MANAGEMENT PLAN OF SOLID WASTE FROM SMALL CAST IRON FOUNDRIES

    Directory of Open Access Journals (Sweden)

    Carlos Alberto Mendes Moraes

    2013-12-01

    Full Text Available The foundry industry contributes to society meeting the demand of metal scrap recycling, but, at the same time, it brings a high risk of environmental impact for its many potentially pollutant wastes. Among these, there are slag and used foundry sand (cold cure molding. Through a survey about the production process of a small cast iron company, the collected data was compiled to determine the organizational setting in terms of generation and segregation of waste. From a complete environmental diagnosis carried out in eight small cast iron foundries, one of them was chosen to be a basis for the elaboration of an industrial solid waste management plan, which is becoming necessary to know and manage the generation of wastes qualitatively and quantitatively. A data assessment about the production process was carried out and compiled to determine the actual organizational scenario. As a result of that, it is possible to create a favorable environment to develop tools for environmental impacts prevention, which will permit the migration for more complex actions on the direction of more efficient process, cleaner production, and internal and external recycling of exceeding materials.

  15. Lung function and functional capacity among foundry workers using effective risk control measures.

    Science.gov (United States)

    Bernardes, Rosane Andrea Bretas; Chiavegato, Luciana Dias; de Moraes, Mônica Vasconcelos; Negreiros, Alexandher; Padula, Rosimeire Simprini

    2015-01-01

    Inhaled dust in the environment can trigger specific reactions in the airways and cause various respiratory diseases. Evaluate the lung function and functional capacity of foundry workers who are exposed to metals and use effective control measures. A cross-sectional study was realized with 108 workers at a bronze foundry and machining plant and in maintenance at a private university, both in Brazil. The workers were divided into two groups: the study group exposed to metals but using risk control measues and a control group not exposed to metal work. The Medical Research Council Questionnaire on Respiratory Symptoms and the International Physical Activity Questionnaire were administered, and lung function and functional capacity were evaluated. Comparative statistics were used to identify differences in the outcome measures between the two groups. The groups had similar personal and anthropometric characteristics and time on the job. Spirometry and peak expiratory flow presented no significant differences between the groups. And there was also no statistically significant difference between groups in functional capacity as assessed by performance on the six-minute walk test. Foundry industry workers in Brazil who were exposed to metal but used risk control measures had similar lung function and functional capacity when compared to the control group who were not exposed to metal. This is a positive results and maybe related to age, time exposure and control of occupational hazards. However, these workers need to continue being monitored in longitudinal studies.

  16. Energy and materials flows in the fabrication of iron and steel semifinished products

    Energy Technology Data Exchange (ETDEWEB)

    Darby, J.B. Jr.; Arons, R.M.

    1979-08-01

    The flow of energy and materials in the fabrication of iron and steel semifinished products from molten metal is discussed. The focus is on techniques to reduce the amount of energy required to produce the typical products of integrated steel plants and iron and steel foundries. In integrated steel plants, if only 50% of the steel being cast were continuously cast, industry-wide energy consumption would be reduced by 6 to 15%. Further major energy savings could be achieved by increased use of by-product gases and regenerators in the various reheat operations. Finally, systems optimization studies to maintain the even flow of materials at full capacity should yield further improvements in energy efficiency. In foundry operations, alternate heating methods in forging operations and the use of no-bake molding and core materials should result in substantial energy savings. Studies of specific operations will suggest housekeeping changes to minimize wasted energy. These changes might include fixing heat leaks, reducing floor space requirements, improving temperature regulation, lowering working temperatures in some steel-forming operations, redesigning products, and minimizing scrap generation. There is also a need for new, energy conserving technologies. A good example would be the development of nondestructive testing to determine the existence, location, and size of defects in ingots at elevated temperatures. A second example is the need to reduce, through system studies, the large amount of scrap typical of foundry operations. Finally, computer control of steel mill operations (materials flow, furnace residence times, excessive heating or overheating, and full capacity utilization of all facilities at all times) deserves further study.

  17. The Protozoa, A Kingdom By Default?

    Science.gov (United States)

    Blackwell, Will H.; Powell, Martha J.

    2001-01-01

    Changes in the concepts of kingdoms of organisms are substantial and Protozoa is loosely characterized. Presents a case explaining how Protozoa interface with other kingdoms of organisms now recognized. (Contains 55 references.) (ASK)

  18. Teaching Taxonomy: How Many Kingdoms?

    Science.gov (United States)

    Case, Emily

    2008-01-01

    Taxonomy, the identification, naming, and classification of living things, is an indispensable unit in any biology curriculum and indeed, an integral part of biological science. Taxonomy catalogues life's diversity and is an essential tool for communication. Textbook discussions of taxonomy range anywhere from three to eight domains of kingdoms.…

  19. Radiation-induced sensitisation of stainless steels

    International Nuclear Information System (INIS)

    Norris, D.I.R.

    1987-01-01

    The book contains the proceedings of a symposium on radiation-induced sensitization of stainless steels, which took place at Berkeley, United Kingdom, 1986. The purpose of the symposium was to examine the mechanism leading to inter-granular corrosion of 20%Cr/25% Ni/Nb stainless steel cladding of AGR fuel following irradiation. Nine papers are presented, of which three are theoretical, two papers are based upon corrosion studies of 20%Cr/25%Ni/Nb steel, and the remaining are concerned with compositional redistribution and its measurement. (U.K.)

  20. Aircraft Steels

    Science.gov (United States)

    2009-02-19

    component usage. PH 13-8Mo is a precipitation-hardenable martensitic stainless steel combining excellent corrosion resistance with strength. Custom 465 is...a martensitic , age-hardenable stainless steel capable of about 1,724 MPa (250 ksi) UTS when peak-aged (H900 condition). Especially, this steel can...NOTES 14. ABSTRACT Five high strength steels (4340, 300M, AerMet 100, Ferrium S53, and Hy-Tuf) and four stainless steels (High Nitrogen, 13

  1. Linking energy efficiency and innovation practices: Empirical evidence from the foundry sector

    International Nuclear Information System (INIS)

    Cagno, Enrico; Ramirez-Portilla, Andres; Trianni, Andrea

    2015-01-01

    The Europe 2020 strategy currently promotes energy efficiency and innovation through disconnected targets focusing on either energy or R&D. Similar policies indicate that in practice, these two concepts are usually perceived as mutually exclusive. Furthermore, evidence in the literature regarding the relationship between R&D and energy efficiency is still highly limited. This exploratory study aims to address this gap by investigating the link between innovation practices and energy efficiency through a multiple case study of 30 foundries in Northern Italy. We analysed the firms' innovativeness, measured by internal R&D and Open Innovation practices (inbound and outbound), and energy efficiency, measured by specific energy consumption, level of adoption of energy-efficient technologies and barriers to energy efficiency. The results seem to show that those foundries complementing internal R&D with inbound practices have a higher level of energy efficiency, a higher level of adoption of available technologies, and a lower perception of barriers to efficiency improvements. This finding suggests that diversifying innovation practices could lead to better performance with respect to all three indicators of energy efficiency analysed. This study contributes to understanding how more innovative firms can be more energy efficient, providing interesting highlights for managers and policymakers. -- Highlights: •The relation between innovation practices and energy efficiency is articulated. •The link between innovation practices and energy efficiency is tested for foundries. •Energy efficiency is measured with three different indicators. •Analyses of the relations between these indicators support the link with innovation. •Concurrent adoption of internal R&D and inbound practices leads to higher efficiency

  2. The Analysis of Foundry Engineering of Copper Alloys Based on the Research of a Metallurgist Settlement in Szczepidło

    Directory of Open Access Journals (Sweden)

    Garbacz-Klempka A.

    2017-03-01

    Full Text Available The article presents chosen aspects of foundry engineering of the settlement dwellers, including the archaeometric characteristics and metal science analysis of the artefacts, as well as an attempted reconstruction of the production organization. Discovered in Szczepidło (Greater Poland, the foundry workshop is unique in Central European Bronze Age.

  3. Interaction of smoking, uptake of polycyclic aromatic hydrocarbons, and cytochrome P450IA2 activity among foundry workers

    DEFF Research Database (Denmark)

    Sherson, D; Sigsgaard, T; Overgaard, E

    1992-01-01

    .56-5.24). The same was true for smoking controls and foundry workers (9.10, 95% CI 8.00-10.20 and 8.69, 95% CI 7.37-10.01). Both smoking groups had raised IA2 ratios compared with non-smokers (p less than 0.01). Non-smoking controls and foundry workers had similar hpU concentrations (0.16, 95% CI 0.10-0.22 and 0...... hygienic samples (respirable dust 1.2 to 3.52 mg/m3 (93 samples)) and as total PAH (0.46 micrograms/m3) and pyrene concentrations (0.28 micrograms/m3) (six samples). Non-smoking controls and foundry workers had similar IA2 ratios (5.63, 95% confidence interval (95% CI) 4.56-6.70 and 4.40, 95% CI 3...

  4. Foundry industries: environmental aspects and environmental condition indicators; Industrias de fundicion: aspectos ambientales e indicadores de condicion ambiental

    Energy Technology Data Exchange (ETDEWEB)

    Sosa, B. s.; Banda-Noriega, R. B.; Guerrero, E. M.

    2013-03-01

    Nowadays, environmental indicators are widely used as effective tools to assist decision-making in both public and private sectors. The lack of literature and research about local and regional Environmental Condition Indicators (ECI), the poor knowledge regarding solid waste generation, effluents and gas emissions from foundry industries, and their particular location in the urban area of Tandil, Argentina are the main reasons for this investigation, aiming to develop a set a of ECI to provide information about the environment in relation to the foundry industry. The study involves all the foundries located in the city between March and April 2010. The set of ECI developed includes 9 indicators for air, 5 for soil and 1 for water. Specific methodology was used for each indicator. (Author) 31 refs.

  5. Use of wasted foundry sand (WFS) as a partial substitute for silica in a soda lime glass

    International Nuclear Information System (INIS)

    Martin, A.C.; Ueno, O.K.; Folgueras, M.V.

    2016-01-01

    The waste foundry sand (WFS) is the main waste generates in foundry industries. Studies in the literature suggest the use of WFS in different materials, such as concrete, brick or asphalt. This work aims to partially replace the silica of a soda-lime glass by the WFS. The waste foundry sand has in its composition elements such as iron and aluminum that can affect the glass quality, which justifies the residue processing to reduce the impurity content. The treatments, that included mechanical agitation and thermal treatment, resulted in a slight decrease in the percent of iron with consequent increase of the silica content. After treatment, some sands were incorporated into the glass, that showed green color but with lower absorption intensity for the sand with less iron content. It was observed that it's possible to obtain glasses using WFS, however, there is difficulty in color controlling. (author

  6. New sol–gel refractory coatings on chemically-bonded sand cores for foundry applications to improve casting surface quality

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Poulsen, T.; Stage, R.K.

    2011-01-01

    Foundry refractory coatings protect bonded sand cores and moulds from producing defective castings during the casting process by providing a barrier between the core and the liquid metal. In this study, new sol–gel refractory coating on phenolic urethane cold box (PUCB) core was examined. The coa......Foundry refractory coatings protect bonded sand cores and moulds from producing defective castings during the casting process by providing a barrier between the core and the liquid metal. In this study, new sol–gel refractory coating on phenolic urethane cold box (PUCB) core was examined......–gel coated cores have better surface quality than those from uncoated cores and comparable surface quality with the commercial coatings. Therefore, the new sol–gel coating has a potential application in the foundry industry for improving the surface finish of castings thereby reducing the cost of fettling...

  7. Energy conservation in flame-heated hearth furnaces in aluminium foundries. Pt. 1

    Energy Technology Data Exchange (ETDEWEB)

    Moser, R

    1981-01-01

    There are two fields for energy saving: The aluminium foundries obtain the electrolytic metal in liquid form and therefore also excessive heat. This must be used. The furnaces must be designed and operated so that they use as little energy as possible. Both subjects are investigated by considering 59 existing plants in Europe. They are compared regarding energy consumption and heat balance. A series of possibilities for improved use of fuel, such as improvement of the burner setting, automatic regulation of excess air and use of combustion with enriched oxygen supply are given.

  8. Free radicals of an aromatic nature in air samples from iron foundries

    Energy Technology Data Exchange (ETDEWEB)

    Westerberg, L M

    1982-01-01

    Free radicals of relatively long life were identified as spin adducts of phenyl-N-tert-butylnitrone. Pyrolysis studies showed the radicals were oxy-radicals. The hyperfine splitting constants of spin adducts of radicals from the pyrolysis in air of benzo(a)pyrene, coal tar pitch, and moulding sand containing hard coal dust were the same as those of the radicals found in foundry air. Since these radicals can bind to DNA, they must be considered when estimating the hazardous effects of polluted air.

  9. Determination of pollutants in foundry during the manufacture of metal constructions for high buildings

    Science.gov (United States)

    Ivanova, Irina; Sushko, Elena; Lyshnikova, Anna; Prykina, Larisa

    2018-03-01

    Current developments are devoted to the environmental safety of the foundry. There is a significant amount of pollutants, according to dust, which is released in the working area, during the manufacture of metal structures for high buildings. From the point of dust extraction, the most unfavorable areas are shot blasting, sand-blasting chambers and knockout grills. The weight fraction of dust composition with diameters up to 20 μm reaches 43,8% by mass, according to experimental analysis. This kind of dust is the most dangerous to employees and also it creates problems for dust-cleaning in the air.

  10. Replies to Challenges in the Field of Air Pollution Control in Foundry Plants

    Directory of Open Access Journals (Sweden)

    Margraf R.

    2012-09-01

    Full Text Available The solution of applications for air pollution control in foundries for iron and non-ferrous metals may not only be understood as the observance of requested emission limit values at the stack outlet. An effective environmental protection already starts with the greatest possible capture of pollutants at the source with at the same time minimisation of the volume flow necessary for this. Independent of this, the downstream installed filtration system has to realise a degree of separation of definitely above 99%.

  11. Comparative Analysis of the Thermal Insulation of Traditional and Newly Designed Protective Clothing for Foundry Workers

    Directory of Open Access Journals (Sweden)

    Iwona Frydrych

    2016-09-01

    Full Text Available An objective of the undertaken research was checking the applicability of aluminized basalt fabrics for the production of clothing for foundry workers. The results of flammability, the resistance to contact, convective and radiation heat, as well as the resistance to big molten metal splashes confirmed the thesis of applicability of the packages with the use of aluminized basalt fabric content for the assumed purpose; therefore, such protective clothing was produced. Thermal comfort of foundry workers is very important and related to many factors, i.e., the structure of the protective clothing package, the number of layers, their thickness, the distance between the body and appropriate underwear. In the paper, a comparison of the results of thermal insulation measurement of two kinds of protective clothing is presented: the traditional one made of aluminized glass fabrics and the new one made of aluminized basalt fabrics. Measurements of clothing thermal insulation were conducted using a thermal manikin dressed in the protective clothing and three kinds of underwear products covering the upper and lower part of the manikin.

  12. Replies to Challenges in the Field of Air Pollution Control in Foundry Plants

    Directory of Open Access Journals (Sweden)

    R. Margraf

    2012-09-01

    Full Text Available The solution of applications for air pollution control in foundries for iron and non-ferrous metals may not only be understood as theobservance of requested emission limit values at the stack outlet. An effective environmental protection already starts with the greatest possible capture of pollutants at the source with at the same time minimisation of the volume flow necessary for this. Independent of this, the downstream installed filtration system has to realise a degree of separation of definitely above 99%.Furthermore, when selecting the filter construction, attention has to be paid to a high availability. An even temporarily productionwithout filter will more and more no longer be accepted by residents and authorities. Incidents at the filter lead to a shutdown of the whole production.Additional measures for heat recovery while preparing concepts for filtration plants help to reduce the energy consumption and servefor a sustained conservation of environment.A consequent consideration of the items above is also condition for the fact that environmental protection in foundries remainsaffordable. The lecture deals with the subjects above from the point of view of a plant constructor.

  13. Risk assessment in a foundry unit by energy trace and barrier analysis method (ETBA

    Directory of Open Access Journals (Sweden)

    S.A. Ayati

    2010-01-01

    Full Text Available Background and aimsAs a Development of Industrial process, human, environment,equipment, material and validity of system has been exposed to hazardous conditions. Regards of32.3 percent of occupations in industries, this study focused on risk assessment of foundry unit byenergy trace and barrier analysis (ETBA method and presented approaches to control of accident.Methodsthe recent study is as a case study one to risk assessment in a foundry unit in Qazvinindustrial city in1387. In this study risks were founded by ETBA method and evaluated by MILSTD-882B. Data were collected by direct observations, interview with workers and supervisorand engineers, walking-talking through method, documents investigation of operationalprocessors, preventive maintenances, equipment technical properties, accidental and medicaldocuments. Finally ETBA worksheets completed.Findingstotally 154 risks has been found. 40 from total are been unacceptable risk, 68unfavorable and also 46 acceptable but with remediation action. Casting workshop had risks morethan other workshops (with 74 identified risks.Potential and heat energies were founded as mosthazardous energies, with respectively 51 and 38 risk cases.ConclusionThis study recommended to be done actions for identification and control risk,such as: safety training, occupation training, preventive maintenance, contract safety, safetycommunication and safety audit group.

  14. Tools and Strategies for Product Life Cycle Management ñ A Case Study in Foundry

    Science.gov (United States)

    Patil, Rajashekar; Kumar, S. Mohan; Abhilash, E.

    2012-08-01

    Advances in information and communication technology (ICT) have opened new possibilities of collaborations among the customers, suppliers, manufactures and partners to effectively tackle various business challenges. Product Life Cycle Management(PLM) has been a proven approach for Original Equipment Manufacturers (OEMs) to increase their productivity, improve their product quality, speed up delivery, and increase their profit and to become more efficient. However, their Tier 2 and Tier 3 suppliers like foundry industries are still in their infancy without adopting PLM. Hence to enhance their understanding, the basic concepts, the tools and strategies for PLM are presented is this paper. By selecting and implementing appropriate PLM strategies in a small foundry, an attempt was also made to understand the immediate benefits of using PLM tools (commercial PLM software and digital manufacturing tools). This study indicated a reduction in lead time and improved utilization of organizational resources in the production of automobile impeller. These observations may be further extrapolated to other multiproduct, multi-discipline and multi-customer companies to realize the advantages of using PLM technology

  15. Waste Foundry Sand Usage for Building Material Production: A First Geopolymer Record in Material Reuse

    Directory of Open Access Journals (Sweden)

    Neslihan Doğan-Sağlamtimur

    2018-01-01

    Full Text Available In order to bring a solution to the problem of waste foundry sand (WFS in the foundry sector and achieve its reuse, geopolymer building material (as a cementless technology was produced from the WFS for the first time in the literature in this study. The physical and mechanical characteristics of this material were determined. In the first part of the experimental step, the sieve analysis, loose/tight unit weight, and loss of ignition of the WFS were obtained as well as the ultimate analysis. In the second step, the water absorption percentage, porosity, unit weight, and compressive strength tests were conducted on the WFS-based geopolymer specimens activated by chemical binders (sodium hydroxide: NaOH and sodium silicate: Na2SiO3. As the unit weights of all the produced samples were lower than 1.6 g/cm3, they may be considered as lightweight building materials. The minimum compressive strength value for building wall materials was accepted as 2.5 MPa by national standards. In this study, the maximum compressive strength value was measured as 12.3 MPa for the mixture incorporation of 30% Na2SiO3 at the curing temperature of 200°C in 28 days. It was concluded that this geopolymer material is suitable for using as a building wall material.

  16. A Production Planning Model for Make-to-Order Foundry Flow Shop with Capacity Constraint

    Directory of Open Access Journals (Sweden)

    Xixing Li

    2017-01-01

    Full Text Available The mode of production in the modern manufacturing enterprise mainly prefers to MTO (Make-to-Order; how to reasonably arrange the production plan has become a very common and urgent problem for enterprises’ managers to improve inner production reformation in the competitive market environment. In this paper, a mathematical model of production planning is proposed to maximize the profit with capacity constraint. Four kinds of cost factors (material cost, process cost, delay cost, and facility occupy cost are considered in the proposed model. Different factors not only result in different profit but also result in different satisfaction degrees of customers. Particularly, the delay cost and facility occupy cost cannot reach the minimum at the same time; the two objectives are interactional. This paper presents a mathematical model based on the actual production process of a foundry flow shop. An improved genetic algorithm (IGA is proposed to solve the biobjective problem of the model. Also, the gene encoding and decoding, the definition of fitness function, and genetic operators have been illustrated. In addition, the proposed algorithm is used to solve the production planning problem of a foundry flow shop in a casting enterprise. And comparisons with other recently published algorithms show the efficiency and effectiveness of the proposed algorithm.

  17. Kingdom, covenant, and human rights

    Directory of Open Access Journals (Sweden)

    Koos Vorster

    2017-07-01

    Full Text Available This research revisits the idea of a Christian perspective on human rights. Departing from a hermeneutics of trust, this article considers the concept of human rights from the perspective of revelation history. Revelation history departs from the consent of the parts of Scripture, irrespective of differences in dating, original languages, canonical differentiation, cultural, social and historical contexts. Scripture offers a theological unity consisting of various topics which are developed continuing and purposeful throughout the biblical revelation. Two of the major topics in Scripture as they are revealed by a revelation historical survey are the concepts kingdom of God and the covenant of God with God’s people. In this article these two concepts will be used as a foundation for a Christian theory of human rights both as legal human rights and moral human rights. The central theoretical argument of this investigation is that both the concepts kingdom and covenant are essentially about justice and relationships – the justice of the kingdom and the relation between God and humankind, the relation between people and the relation between humans and creation. These relations are the essence of the rights people have, vis-à-vis the authority of the day and other people. These rights, which deal with the orderly maintenance of relationships, can be formalised in legal human rights and should be nurtured and protected by the civil authorities. Christians and churches as moral agents in society have the calling to promote the idea of human rights in constitutional democracies.

  18. Steel making

    CERN Document Server

    Chakrabarti, A K

    2014-01-01

    "Steel Making" is designed to give students a strong grounding in the theory and state-of-the-art practice of production of steels. This book is primarily focused to meet the needs of undergraduate metallurgical students and candidates for associate membership examinations of professional bodies (AMIIM, AMIE). Besides, for all engineering professionals working in steel plants who need to understand the basic principles of steel making, the text provides a sound introduction to the subject.Beginning with a brief introduction to the historical perspective and current status of steel making together with the reasons for obsolescence of Bessemer converter and open hearth processes, the book moves on to: elaborate the physiochemical principles involved in steel making; explain the operational principles and practices of the modern processes of primary steel making (LD converter, Q-BOP process, and electric furnace process); provide a summary of the developments in secondary refining of steels; discuss principles a...

  19. Introducing radioactivity monitoring systems in the production of steel

    International Nuclear Information System (INIS)

    Sofilic, T.; Marjanovic, T.; Rastovcan-Mioc, A.

    2005-01-01

    Over the last twenty years, a significant number of cases of radioactive pollution has been recorded in metallurgical processes. However, it is not certain whether the pollution was caused by increased uncontrolled disposal of waste containing radionuclides or whether it was the result of increased radioactivity monitoring and control of metallic scrap. Many metal producers in the world have therefore implemented systematic monitoring of radioactivity in their production processes. Special attention was given to monitoring radioactivity in steel making processes, which is still the most applied construction material with an annual output of over billion tonnes all over the world. Drawing on the experience of the best known steel producers in Europe and world, Croatian steel mills find it necessary and justified to introduce radioactivity monitoring and control systems of radioactive elements in steel scrap, semi-finished and finished products. The aim of this paper is to point out the need to introduce the radioactivity monitoring and control in steel and steel-casting production, and to inform experts in Croatian steel mills and foundries about potential solutions and current systems. At the same time, we wanted to demonstrate how implementation of monitoring equipment can improve quality management and environmental management systems. This would render Croatian products competitive on the European market both in terms of physical and chemical properties and in terms of product quality certificates and radioactivity information. Since we lack our own standards and regulations to control both domestic and imported steel scrap, semi-finished products (crude steel, hot and cold rolled strip) and finished products, we need apply current international recommendations and guidelines, until we design our own monitoring system and adopt relevant legislation on the national level. This paper describes basic types of radioactivity monitoring and control systems, the most

  20. Value-Chain Dynamics of the West Point Foundry, 1817-1911: A Historical Case Analysis in Marketing

    Science.gov (United States)

    Petkus, Ed, Jr.

    2013-01-01

    This case provides the opportunity for students to explore marketing and value/supply-chain dynamics in a unique historical context. The West Point Foundry (WPF), located in Cold Spring, New York, was one of the most important manufacturing ventures in the United States from 1817 to 1911. The case outlines the supply-chain details of the WPF as…

  1. Determining the optimal index of heat stress in foundry, die casting and road construction industries using FAHP_Topsis

    Directory of Open Access Journals (Sweden)

    Maryam Dehghanipoor

    2016-12-01

    Full Text Available Introduction: Heat stress is one of the harmful risks in casting and die casting industries, which can not only cause work-related diseases but also can impair the performance and safety of workers. Since the indicators that are used to evaluate heat stress are very different, it is very difficult to choose a suitable index. The aim of this study was to determine the optimum heat stress index in foundry, die-cast, and road construction industries using FAHP and Topsis methods. Material and Method: In order to determine optimum heat stress index in foundry, die-cast, and road construction industries, first, the prioritization criteria were defined by experts (including ease of measurement, measurement accuracy, comprehensiveness, time, cost, and correlation. Then, considering these criteria, the best heat stress index was determined based on experts’ opinions and using FAHP and Topsis methods. Result: The results of this study suggest that given the current conditions and criteria, WBGT and P4SR is the best indices for foundry, die casting and construction. Conclusion: The results showed that according to comprehensiveness, accuracy and correlation criteria, the WBGT index is considered as the best indicator of heat stress assessment in foundry, die-cast and road construction industries. Moreover, the HSI ranked in the last place due to the complexity and cost of its calculation.

  2. Respirable silica dust exposure amongst foundry workers in Gauteng, South Africa: A task-based risk assessment

    CSIR Research Space (South Africa)

    Khoza, NN

    2012-09-01

    Full Text Available /m³ respectively in foundry two. The maximum exposure concentration was 0.835 mg/m³ and minimum exposure was 0.010 mg/m³. Data were analysed by using SPSS version 18. The highest exposed occupations were moulders, sand mixers, furnace operators, shake...

  3. The Synthetic Aperture Radar Science Data Processing Foundry Concept for Earth Science

    Science.gov (United States)

    Rosen, P. A.; Hua, H.; Norton, C. D.; Little, M. M.

    2015-12-01

    Since 2008, NASA's Earth Science Technology Office and the Advanced Information Systems Technology Program have invested in two technology evolutions to meet the needs of the community of scientists exploiting the rapidly growing database of international synthetic aperture radar (SAR) data. JPL, working with the science community, has developed the InSAR Scientific Computing Environment (ISCE), a next-generation interferometric SAR processing system that is designed to be flexible and extensible. ISCE currently supports many international space borne data sets but has been primarily focused on geodetic science and applications. A second evolutionary path, the Advanced Rapid Imaging and Analysis (ARIA) science data system, uses ISCE as its core science data processing engine and produces automated science and response products, quality assessments and metadata. The success of this two-front effort has been demonstrated in NASA's ability to respond to recent events with useful disaster support. JPL has enabled high-volume and low latency data production by the re-use of the hybrid cloud computing science data system (HySDS) that runs ARIA, leveraging on-premise cloud computing assets that are able to burst onto the Amazon Web Services (AWS) services as needed. Beyond geodetic applications, needs have emerged to process large volumes of time-series SAR data collected for estimation of biomass and its change, in such campaigns as the upcoming AfriSAR field campaign. ESTO is funding JPL to extend the ISCE-ARIA model to a "SAR Science Data Processing Foundry" to on-ramp new data sources and to produce new science data products to meet the needs of science teams and, in general, science community members. An extension of the ISCE-ARIA model to support on-demand processing will permit PIs to leverage this Foundry to produce data products from accepted data sources when they need them. This paper will describe each of the elements of the SAR SDP Foundry and describe their

  4. Recycling radioactive scrap metal by producing concrete shielding with steel granules

    International Nuclear Information System (INIS)

    Sappok, M.

    1996-01-01

    Siempelkamp foundry at Krefeld, Germany, developed a method for recycling radioactively contaminated steel from nuclear installations. The material is melted and used for producing shielding plates, containers, etc., on a cast-iron basis. Because the percentage of stainless steel has recently increased significantly, problems in the production of high-quality cast iron components have also grown. The metallurgy, the contents of nickel and chromium especially, does not allow for the recycling of stainless steel in a percentage to make this process economical. In Germany, the state of the art is to use shielded concrete containers for the transport of low active waste; this concrete is produced by using hematite as an additive for increasing shielding efficiency. The plan was to produce steel granules from radioactive scrap metal as a substitute for hematite in shielding concrete

  5. Design and production of a novel sand materials strength testing machine for foundry applications

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Hansen, K. S.; Tiedje, Niels Skat

    2012-01-01

    testing machine was designed and built for both green sand and chemically-bonded sand materials. This machine measures and presents the loading response as a force-displacement profile from which the mechanical properties of the moulding materials can be deduced. The system was interfaced to a computer......In the foundry, existing strength testing machines are used to measure only the maximum fracture strength of mould and core materials. With traditionally used methods, the loading history to ascertain deformation of the material is not available. In this paper, a novel moulding material strength...... with a commercial PC based-control and data acquisition software. The testing conditions and operations are specified in the user interface and the data acquisition is made according to specifications. The force and displacements were calibrated to ensure consistency and reliability of the measurement data...

  6. Exploitation of the residue of foundry exhauster powder in ceramics for covering

    International Nuclear Information System (INIS)

    Valentina, Luiz Veriano Oliveira Dalla; Folgueras, Marilena Valadares; Knop, Wanessa Rejane; Semptikovski, Simone Claudiano

    2010-01-01

    The work evaluates the possibility of the use the exhauster powder generated in the foundry process in ceramic mass atomized semigre type. This residue was characterized by scanning electron microscopy, x-ray diffractometry and thermal analysis (DSC, TG). Formulations were prepared with different exhauster powder content. The sintered materials between 1000°C at 1 200 deg C. The results showed of the scanning electron microscopy and the characterization of the technological properties (water absorption, linear shrinkage and apparent density) had demonstrated the viability of the use of this residue. Through experiments it was observed that the exhauster powder promoted an increment in the sintering degree, and raised texts of this they increase of the porosity and intensification in the color of the new material. That is, it is possible to incorporate small amounts of the exhauster powder in substitution the substances cousins of natural origin. (author)

  7. [The genetic component of chronic respiratory diseases in workers of foundry productions].

    Science.gov (United States)

    Loskutov, D V; Khamitova, R Ya

    Review of the literature shows that currently there is an accumulation of data on the genetic determination of individual susceptibility to adverse industrial factors. Material of the research were high molecular DNA samples isolated from epithelial mouth scrapings in 99 foundry workers. Study of polymorphic variants of interleukin genes was performed by means of the analysis ofproducts of amplification of specific regions of the genome. Homozygous genotype TNF-a (-308A/G) was established to increase the relative risk of shaping of chronic respiratory diseases: with AA alleles - by 6.4 times and GG alleles - by 2.4 times, while the heterozygous genotype (AG) decreases - by 1. 9 times. Polymorphism of gene IL-1β (+3953 T / C) had no significance for the development of respiratory disease. Genotyping interleukins, involved in the inflammatory responses of the bronchopulmonary tract, can be considered as an element ofprimary prevention in industries with a high risk for shaping of respiratory diseases.

  8. The effect of main alloying elements on the physical properties of Al–Si foundry alloys

    International Nuclear Information System (INIS)

    Stadler, F.; Antrekowitsch, H.; Fragner, W.; Kaufmann, H.; Pinatel, E.R.; Uggowitzer, P.J.

    2013-01-01

    In this study we describe the effect of the main alloying elements Si, Cu and Ni on the thermal properties of hypoeutectic and near-eutectic Al–Si foundry alloys. By means of systematic variations of the chemical composition, the influence of the amount of ‘second phases’ on the thermal conductivity, thermal expansion coefficient, and thermal shock resistance is evaluated. Thermodynamic calculations predicting the phase formation in multi-component Al–Si cast alloys were carried out and verified using SEM, EDX and XRD analysis. The experimentally obtained data are discussed on a systematic basis of thermodynamic calculations and compared to theoretical models for the thermal conductivity and thermal expansion of heterogeneous solids.

  9. MODERN RESOURCE-SAVING TECHNOLOGIES IN FOUNDRY PRODUCTION OF JSC «MINSK TRAKTOR PLANT»

    Directory of Open Access Journals (Sweden)

    F. A. Domotenko

    2016-01-01

    Full Text Available In article the main world tendencies of development of the production technology of sandy cores and value of this production in complex technology of manufacture of castings are considered. It is established that the most rational way of production technically and economically is manufacture of wafer sandy cores using the Cold-box-amin technology. Scientific, technical, technological and economic aspects of modernization of foundry production of JSC MTZ with complete transition to production of sandy cores on the resource-saving Cold-box-amin technology are provided. The main distinctive feature of this reequipment – all planned works are based on the domestic technological developments and the equipment created in the cooperation by specialists of JSC BELNIILIT and JSC MTZ. Within GNTP essential support to the provided works was given by the state.

  10. The analysis of the wax foundry models fabrication process for the CPX3000 device

    Directory of Open Access Journals (Sweden)

    G. Budzik

    2011-04-01

    Full Text Available The paper presents possibilities of creating wax founding models by means of CPX3000 device. The device is used for Rapid Prototypingof models made of foundry wax in an incremental process. The paper also presents problems connected with choosing technologicalparameters for incremental shaping which influence the accuracy of created models. Issues connected with post-processing are alsodescribed. This process is of great importance for obtaining geometrically correct models. The analysis of parameters of cleaning models from supporting material is also presented. At present CPX3000 printer is the first used in Poland device by 3D Systems firm for creating wax models. The printer is at The Faculty of Mechanical Engineering at Rzeszów University of Technology.

  11. Strobloy — The New Combined Grain Refiner and Modifier for Hypoeutectic AlSi Foundry Alloys

    Science.gov (United States)

    Bondhus, Eivind; Sagstad, Trond

    Hydelko presents a new combination alloy for use in hypoeuctectic aluminium silicon foundry alloys. Strobloy simplifies today's addition practice of grain refiner and modifier by reducing the number of additions from two to one. Strobloy is a combination product between the well-established TiBloy, and strontium. The alloy contains nucleating particles in the form of the mixed boride (Al, Ti)B2, which is beneficial regarding settling and grain refining efficiency. Strontium is present as fast-dissolving AL4Sr particles. Trials carried out indicate that Strobloy shows very good performance compared to separate additions of TiBloy/AlTi5B1 and AlSr master alloy. The grain refining efficiency and modification level is the same or better. This paper displays results collected from tests done with different strontium levels in an A356 alloy. Comparisons to separate additions of TiBloy and AlSr are presented.

  12. Aluminum, Iron and Steel, and Foundry Industries. Reprinted from the Occupational Outlook Handbook, 1978-79 Edition.

    Science.gov (United States)

    Bureau of Labor Statistics (DOL), Washington, DC.

    Focusing on occupations in the various metal industries, this document is one in a series of forty-one reprints from the Occupational Outlook Handbook providing current information and employment projections for individual occupations and industries through 1985. The specific occupations covered in this document include occupations in the aluminum…

  13. Is It Kingdom or Domains? Confusion & Solutions

    Science.gov (United States)

    Blackwell, Will H.

    2004-01-01

    A confusion regarding the number of kingdoms that should be recognized and the inclusion of domains in the traditional kingdom-based classification found in the higher levels of classification of organisms is presented. Hence, it is important to keep in mind future modifications that may occur in the classification systems and to recognize…

  14. Beyond barriers – A case study on driving forces for improved energy efficiency in the foundry industries in Finland, France, Germany, Italy, Poland, Spain, and Sweden

    International Nuclear Information System (INIS)

    Thollander, Patrik; Backlund, Sandra; Trianni, Andrea; Cagno, Enrico

    2013-01-01

    Highlights: • Results are based on a questionnaire in the European foundry industry. • The energy efficiency potential is assed to be 7.5% of the total energy use. • Most important drivers to and barriers for energy efficiency are financial followed by organizational. • EPC is used among 23% of the foundries, third party financing among 12%. • Large energy management improvement potentials are uncovered. - Abstract: Energy management plays an important role in the transformation of industrial energy systems towards improved energy efficiency and increased sustainability. This paper aims to study driving forces for improved energy efficiency in some European energy-intensive foundry industries. The investigation has been conducted as a multiple case study involving 65 foundries located in Finland, France, Germany, Italy, Poland, Spain, and Sweden. The most relevant perceived driving forces were found to be financially related, followed by organizational driving forces. Nevertheless, some differences can be appreciated according to the firm’s size and country. Almost half of the studied foundries lack a long-term energy strategy, about one-fourth stated that they have used Energy Performance Contracting (EPC), and only approximately one in ten foundries have used Third Party Financing (TPF). Among the studied foundries, three out of five have conducted an energy audit. On average, the energy saving potential according to the respondents is stated to be 7.5%. In conclusion, energy management in the European foundry industry, despite increasing energy prices and extensive energy policy actions taken by the EU, still seems to have great improvement potential, calling for future research and policy actions in the field

  15. Suitability of a South African silica sand for three-dimensional printing of foundry moulds and cores

    Directory of Open Access Journals (Sweden)

    Nyembwe, Kasongo

    2016-11-01

    Full Text Available Applications of three-dimensional printing (3DP to metal casting include, among other things, the direct manufacturing of foundry moulds and cores in refractory materials such as silica sand. The main properties of silica sand that are essentially related to the traditional moulding and core-making processes are: size distribution, clay content, pH, acid demand, and refractoriness. The silica sand used for 3DP must also be appropriately selected for the layer-based manufacturing process involved in 3DP. Properties such as grain size distribution, grain surface morphology, angularity, flowability, and recoating abilities have a particular importance when determining sand suitability. Because of these extra requirements, only a limited range of available foundry silica sands can be used for 3DP processes. The latter situation explains the scarcity and high cost of suitable silica sands, thus contributing to the relatively high operational costs of the 3DP processes for the production of sand moulds and cores. This research paper investigates the suitability of a locally-available silica sand for use in a Voxeljet VX1000 3DP machine. The local silica sand was assessed and compared with an imported silica sand recommended by the manufacturer of 3DP equipment in terms of foundry characteristics and recoating behaviour. The study shows that, despite the differences between the characteristics of the two silica sands, the local sand could be considered a suitable alternative to imported sand for rapid sand casting applications.

  16. Risk assessment related to manual handling on choosen work possition in foundry Alstom Power Sp. z o. o.

    Directory of Open Access Journals (Sweden)

    G. Kowal

    2010-04-01

    Full Text Available Manual handling remains one of the different types of transport inside working place, although technological progress and modernorganization of work. Manual transport as a transport inside working place is related to foundry industry. According to polish lawregulations employer has to give consideration to manual handling in professional risk assessment and introduce actions for manualhandling reduction. In Foundry Elblag case there is found that in many processes manual handling are made by workers. For example wecan choose melting processes (additives manual feeding, mixing and pulling metallurgical slag, etc. or fettling processes like grinding.Objective of that analysis was to define level of risk related to manual handling in work stand chosen and define activities impacted onrisk assessment result with biggest range. For risk reduction, technical and organizational solutions were shown (better ergonomically work stand, method of work and worker’s awareness about good practices. In this study methods related to manual handling risk assessment were described, focus on KIM method used in Foundry Elblag. Key Item Method allow to estimate the risk by simple calculation based on key indicators (time rating points, rating points of mass, posture or work condition. Points were chosen based on timekeeping, information from workers and foreman.

  17. Combining optimisation and simulation in an energy systems analysis of a Swedish iron foundry

    International Nuclear Information System (INIS)

    Mardan, Nawzad; Klahr, Roger

    2012-01-01

    To face global competition, and also reduce environmental and climate impact, industry-wide changes are needed, especially regarding energy use, which is closely related to global warming. Energy efficiency is therefore an essential task for the future as it has a significant impact on both business profits and the environment. For the analysis of possible changes in industrial production processes, and to choose what changes should be made, various modelling tools can be used as a decision support. This paper uses two types of energy analysis tool: Discrete Event Simulation (DES) and Energy Systems Optimisation (ESO). The aim of this study is to describe how a DES and an ESO tool can be combined. A comprehensive five-step approach is proposed for reducing system costs and making a more robust production system. A case study representing a new investment in part of a Swedish iron foundry is also included to illustrate the method's use. The method described in this paper is based on the use of the DES program QUEST and the ESO tool reMIND. The method combination itself is generic, i.e. other similar programs can be used as well with some adjustments and adaptations. The results from the case study show that when different boundary conditions are used the result obtained from the simulation tools is not optimum, in other words, the result shows only a feasible solution and not the best way to run the factory. It is therefore important to use the optimisation tool in such cases in order to obtain the optimum operating strategy. By using the optimisation tool a substantial amount of resources can be saved. The results also show that the combination of optimisation and simulation tools is useful to provide very detailed information about how the system works and to predict system behaviour as well as to minimise the system cost. -- Highlights: ► This study describes how a simulation and an optimisation tool can be combined. ► A case study representing a new

  18. The comparative studies of ADI versus Hadfield cast steel wear resistance

    Directory of Open Access Journals (Sweden)

    Mieczysław Kaczorowski

    2011-04-01

    Full Text Available The results of comparative studies of wear resistance of ADI versus high manganese Hadfield cast steel are presented. For evaluation ofwear resistance three type of ADI were chosen. Two of them were of moderate strength ADI with 800 and 1000MPa tensile strength whilethe third was 1400MPa tensile strength ADI. The specimens were cut from ADI test YII type casting poured and heat treated in Institute ofFoundry in Krakow. The pin on disc method was used for wear resistance experiment. The specimens had a shape of 40mm long rod withdiameter 6mm. The load and speed were 100N and 0,54m/s respectively. It was concluded that the wear resistance of ADI is comparablewith high manganese cast steel and in case of low tensile grade ADI and is even better for high strength ADI than Hadfield steel.

  19. Lysozymes in the animal kingdom.

    Science.gov (United States)

    Callewaert, Lien; Michiels, Chris W

    2010-03-01

    Lysozymes (EC 3.2.1.17) are hydrolytic enzymes, characterized by their ability to cleave the beta-(1,4)-glycosidic bond between N-acetylmuramic acid and N-acetylglucosamine in peptidoglycan, the major bacterial cell wall polymer. In the animal kingdom, three major distinct lysozyme types have been identified--the c-type (chicken or conventional type), the g-type (goose-type) and the i-type (invertebrate type) lysozyme. Examination of the phylogenetic distribution of these lysozymes reveals that c-type lysozymes are predominantly present in the phylum of the Chordata and in different classes of the Arthropoda. Moreover, g-type lysozymes (or at least their corresponding genes) are found in members of the Chordata, as well as in some bivalve mollusks belonging to the invertebrates. In general, the latter animals are known to produce i-type lysozymes. Although the homology in primary structure for representatives of these three lysozyme types is limited, their three-dimensional structures show striking similarities. Nevertheless, some variation exists in their catalytic mechanisms and the genomic organization of their genes. Regarding their biological role, the widely recognized function of lysozymes is their contribution to antibacterial defence but, additionally, some lysozymes (belonging to different types) are known to function as digestive enzymes.

  20. Decommissioning: a United Kingdom perspective

    International Nuclear Information System (INIS)

    Haworth, A.; Reed, D.L.; Bleeze, A.

    1995-01-01

    The paper considers the United Kingdom legislative framework relevant to decommissioning of facilities on nuclear licensed sites. It describes the various legislative bodies involved in regulating this activity and the inspectorate concerned. The licensing regime is described in some detail highlighting the UK arrangements whereby a license is granted for the site upon which nuclear facilities are planned or exist. The license remains in place throughout the life of the plant on the site: from initial planning through to the end of decommissioning. A site (of part of) is not de-licensed until it can be stated that there has ceased to be any danger from ionising radiations from anything on the site (or appropriate part of the site). The final part of the paper considers the changes arising from the commercialization of the nuclear power industry in UK and the restatement of the Nuclear Installation Inspectorate's policy on decommissioning which has arisen as a result of a review made in response to these changes. (author)

  1. United Kingdom electric system privatization

    Energy Technology Data Exchange (ETDEWEB)

    Lolli, A. (Bologna Univ. (Italy))

    1992-03-01

    This paper reviews the mechanics and first results of deregulation in the electric power industry of the United Kingdom. Several aspects are dealt with, namely: 1983 Energy Act impacts on ownership and subsequent changes brought about by the 1989 Energy Act; the Act's stipulations with regard to share acquisition and distribution; the division of the patrimony of the Area Boards; natural monopolistic characteristics of power distribution; vertical integration in Scotland, target investment limits in Government and public participation; the 'golden share' concept to guarantee public participation; current 40% share ownership by the Government; 15% private ownership limit for individual investors; external control by Government of licensing and rate structure setting; the impacts of organizational changes on the overall cost benefits of deregulation; modified Governmental regulatory powers; measures to ensure competition and consumer protection; provisions regarding misbehaviour; second tier suppliers and reserve fuel supply obligations; deregulation impacts on nuclear power marketing; power pooling regulations; installation of new transmission lines; provisions encouraging the use of diverse energy sources; franchising; interconnection with national grid; regulation of technical operations; standby as it affects rate structure; and spot market pricing.

  2. Management information systems. [United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, D.; Spence, A.C.

    1985-02-01

    The successful application in the United Kingdom of the real time monitoring and control systems (MINOS) for underground mining operations, particularly in coal transport and the development of coalface monitoring (FIDO) in 1980 led naturally to the design of an operational data base for management. A User Group of experienced colliery managers produced a Management Information System (MIS) requirements specification and began the evolution of the systems of today. Twenty-four mines operate MIS in different ways from total dependency to a means of checking their manual reporting system. MIS collects useful data from all the major MINOS applications and provides a means of manually inputting other, relevant information. A wide variety of displays and reports are available to management, adjusted to meet individual requirements. The benefits from the use of MIS are difficult to quantify, since they become part of the management process. Further developments are taking place based on operational experience and requirements and taking advantage of the recent advances in computer technology. MIS is the modern management tool in British coal mining, collecting, storing, analysing and presenting accurate information upon which management decision making is based.

  3. Devolution in the United Kingdom

    Directory of Open Access Journals (Sweden)

    Marković Ratko

    2014-01-01

    Full Text Available Devolution is a transfer of the legislative powers of the Westminster Parliament to the parliaments of the historical provinces once united with England into the United Kingdom, which are directly elected by the provincial population. That delegation is asymmetrical and revocable, but it does not affect the basic norms of the British unwritten constitution on parliamentary supremacy. Over the devolution the provinces do not acquire the primary competence, but the one that is given to them by the transfer of the legislative powers of the Westminster Parliament. A special law retaining the Westminster Parliament's primary competence and sovereignty grants this competence. Regarding the scope of the devolved powers of the provinces and the organizational mechanism for their execution, there is a significant asymmetry. In all the provinces, there is a unique junction between devolved powers and their holders. Before the referendum on the independence in Scotland in September 2014, the increase of devolved powers was promised not only for all the historical provinces (Scotland, Wales, Northern Ireland, but for England as well, which represents a step towards the federalization of the UK. Devolution and several other institutions of the British constitution also, have a stamp 'Made in Britain' which does not allow easy imitation and transfer to another countries and their constitutions.

  4. Health-hazard evaluation report GHETA 83-309-1405, Chrysler Corporation Foundry, Indianapolis, Indiana

    International Nuclear Information System (INIS)

    Patil, A.

    1984-01-01

    In response to a request arising out of employee concerns over the medical surveillance program at the Chrysler Corporation Foundry located in Indianapolis, Indiana, an evaluation was made of chest radiographs evaluated by the program with specific concern directed to disagreement on the radiographic diagnosis of pneumoconiosis. The request was made by the Chrysler Corporation and the United Auto Workers National Joint Committee on Health and Safety. Three NIOSH certified B-readers independently interpreted a set of 78 systematically sampled posteroanterior (PA) chest radiographs from the system files. These interpretations were compared among themselves and with company interpretations. While none of the radiographs was deemed unreadable, 35% were classified as having poor technical quality. Only one film was found which had a profusion of small opacities, and the company had interpreted the film as positive. Overall, agreement on proportion of positive readings and agreement on individual films was as good between the company and B-readers as it was between any two of the individual B-readers. The author recommends, however, that in order to avoid future complaints of the nature, the company should use standard radiographic equipment and techniques, NIOSH certified B-readers, and current international classifications of radiographs for pneumoconioses in their medical surveillance program

  5. Mechanical and Durability Properties of Concrete Made with Used Foundry Sand as Fine Aggregate

    Directory of Open Access Journals (Sweden)

    G. Ganesh Prabhu

    2015-01-01

    Full Text Available In recent years, the construction industry has been faced with a decline in the availability of natural sand due to the growth of the industry. On the other hand, the metal casting industries are being forced to find ways to safely dispose of waste foundry sand (FS. With the aim of resolving both of these issues, an investigation was carried out on the reuse of waste FS as an alternative material to natural sand in concrete production, satisfied with relevant international standards. The physical and chemical properties of the FS were addressed. The influence of FS on the behaviour of concrete was evaluated through strength and durability properties. The test results revealed that compared to the concrete mixtures with a substitution rate of 30%, the control mixture had a strength value that was only 6.3% higher, and this enhancement is not particularly high. In a similar manner, the durability properties of the concrete mixtures containing FS up to 30% were relatively close to those of control mixture. From the test results, it is suggested that FS with a substitution rate of up to 30% can be effectively used in concrete production without affecting the strength and durability properties of the concrete.

  6. Properties of made by different methods of RP impeller foundry patterns

    Directory of Open Access Journals (Sweden)

    G. Budzik

    2007-04-01

    Full Text Available This article presents the tests of properties of foundry patterns of turbocharger turbine impeller. Impellers prototypes were predestinated for casting by method losing patterns. There were carried out tests of these prototypes made by different methods of Rapid Prototyping (RP. Two impeller were made by growth methods: stereolitography (SLA and three dimensional printing (3DP. One prototype was made by the method of Vacuum Casting as a wax casting. Tests were executed in the Department of Machine Design of Rzeszow University of Technology in cooperation with WSK PZL Rzeszow and Car Technology Krakow. First impeller was carried out by method of stereolitography on SLA 250 plant. That pattern was also used to carry out silicon matrix for casting of wax pattern. Next pattern was printed by three dimensional printer Z510 from the powder ZP14. Good removability of the pattern from the mould is particularly essential for impellers of small turbines with blades of small thickness of their section. All pattern were tested on their removability from the ceramic mould. The best melting properties had the wax pattern. Patterns made from resin SL5170 (SLA and powder ZP14 (3DP were removed in the process of burning but about 1% of soot was left in the mould.

  7. Corrosion of immersed ceramic heat exchanger tubes in aluminium foundry baths

    Energy Technology Data Exchange (ETDEWEB)

    Bracho-Troconis, C.B.; Frot, G.; Bienvenu, Y. [Ecole des Mines de Paris, Evry (France). Centre des Materiaux; Frety, N. [Ecole des Mines d`Albi-Carmaux (France); Alliat, I. [CERSTA-Gaz de France, Saint-Denis (France)

    1997-12-31

    The corrosion of three non-oxide ceramics by Al-9Si-3Cu baths and by fluxes (mixtures of chlorides and fluorides of sodium and potassium) at about 750 C was studied in a foundry environment. Comparison of results of the metallurgical examination of A, a silicon-nitride-bonded silicon carbide and of B, a reaction-bonded silicon nitride, surface treated to fill all the external porosity provides some insight into the role of the bonding phase and the porosity. Grade C is a graphite bonded silicon carbide with an external protection by a ceramic glazing. The SiC phase in the tubes is inert to the corrosive liquids (attributed to the silicon content in the metal). A and C ceramics react only in the presence of a flux. Sodium and chlorine were identified in the corrosion products as well as AlN (A) and Al{sub 4}C{sub 3} (C), resulting from reaction of the silicon nitride or of the graphite bonding phase with aluminium. This suggests that the fluxes are responsible for the corrosive process, by causing the formation of gaseous aluminium halides which penetrate the porous bonding phase and react with it to form AlN or Al{sub 4}C{sub 3}. (orig.) 13 refs.

  8. Methods of Computational Intelligence in the Context of Quality Assurance in Foundry Products

    Directory of Open Access Journals (Sweden)

    Rojek G.

    2016-06-01

    Full Text Available One way to ensure the required technical characteristics of castings is the strict control of production parameters affecting the quality of the finished products. If the production process is improperly configured, the resulting defects in castings lead to huge losses. Therefore, from the point of view of economics, it is advisable to use the methods of computational intelligence in the field of quality assurance and adjustment of parameters of future production. At the same time, the development of knowledge in the field of metallurgy, aimed to raise the technical level and efficiency of the manufacture of foundry products, should be followed by the development of information systems to support production processes in order to improve their effectiveness and compliance with the increasingly more stringent requirements of ergonomics, occupational safety, environmental protection and quality. This article is a presentation of artificial intelligence methods used in practical applications related to quality assurance. The problem of control of the production process involves the use of tools such as the induction of decision trees, fuzzy logic, rough set theory, artificial neural networks or case-based reasoning.

  9. Workload assessment on foundry SME to enhance productivity using full time equivalent

    Directory of Open Access Journals (Sweden)

    Sari Amarria Dila

    2018-01-01

    Full Text Available Aluminium SME aims to increase the production amount by producing wok as much as 300 Units. The problem is workload analysis of operator on the wok production line in the wok foundry SME as well as the production cycle-making cycle time and analyze the workload received by the operator when producing 300 woks using the full time equivalent (FTE method. This study aims to measure the workload of each division worker in the production process with a total of 13 workers observed. This study provides a work division recommendation based on the workload that has been carefully examined. This research involves percentage of workload effectiveness and the wages of workers. In lathe division have overload workload. While the printing division, melting inspection division, packaging and transportation division including normal workload category and the percentage of good work effectiveness. The result provides recommendations for the addition of 2 workers in each division that includes the category of overload of the lathe division with the number of initial workers as many as 13 workers to 15 workers. In the last stage perform a simulation by comparing the system of prefix work and proposal. The simulation results obtained with the initial work system to get an average of 223 woks / day. Meanwhile, for the proposed work system to get an average output of 291 woks.

  10. Modeling of the influence of coarsening on viscoplastic behavior of a 319 foundry aluminum alloy

    International Nuclear Information System (INIS)

    Martinez, R.; Russier, V.; Couzinié, J.P.; Guillot, I.; Cailletaud, G.

    2013-01-01

    Both metallurgical and mechanical behaviors of a 319 foundry aluminum alloy have been modeled by means of a multiscale approach. The nano-scale, represented by the coarsening of Al 2 Cu precipitates, has been modeled according to the Lifshitz–Slyozov–Wagner (LSW) law in a range of temperature going from 23 °C to 300 °C up to 1000 h aging time. Results were then compared to transmission electron microscope (TEM) observations and are in good agreement with the experimental measurements. The model allows us to know the critical radius, the volume fraction and the number of particles per μm 3 in a α-phase representative volume element (RVE). The increase in yield stress generated by the interaction of dislocations with precipitates, lattice and solid solution, is modeled on the microscale. The yield stress becomes thus a function of the precipitation state, and is time/temperature dependent. These two models were then combined into a mechanical macroscale model in order to represent the Low Cycle Fatigue (LCF) behavior of the material. An elasto-viscoplastic law has been used and all the material parameters were experimentally determined with LCF stress/strain loops for the first cycle and for the mechanical steady state. The simulation results are in good agreement with the experiments.

  11. Effects of waste glass and waste foundry sand additions on reclaimed tiles containing sewage sludge ash.

    Science.gov (United States)

    Lin, Deng-Fong; Luo, Huan-Lin; Lin, Kuo-Liang; Liu, Zhe-Kun

    2017-07-01

    Applying sewage sludge ash (SSA) to produce reclaimed tiles is a promising recycling technology in resolving the increasing sludge wastes from wastewater treatment. However, performance of such reclaimed tiles is inferior to that of original ceramic tiles. Many researchers have therefore tried adding various industrial by-products to improve reclaimed tile properties. In this study, multiple materials including waste glass and waste foundry sand (WFS) were added in an attempt to improve physical and mechanical properties of reclaimed tiles with SSA. Samples with various combinations of clay, WFS, waste glass and SSA were made with three kiln temperatures of 1000°C, 1050°C, and 1100°C. A series of tests on the samples were next conducted. Test results showed that waste glass had positive effects on bending strength, water absorption and weight loss on ignition, while WFS contributed the most in reducing shrinkage, but could decrease the tile bending strength when large amount was added at a high kiln temperature. This study suggested that a combination of WFS from 10% to 15%, waste glass from 15% to 20%, SSA at 10% at a kiln temperature between 1000°C and 1050°C could result in quality reclaimed tiles with a balanced performance.

  12. The Implementation of Computer Platform for Foundries Cooperating in a Supply Chain

    Directory of Open Access Journals (Sweden)

    Wilk-Kołodziejczyk D.

    2014-08-01

    Full Text Available This article presents a practical solution in the form of implementation of agent-based platform for the management of contracts in a network of foundries. The described implementation is a continuation of earlier scientific work in the field of design and theoretical system specification for cooperating companies [1]. The implementation addresses key design assumptions - the system is implemented using multi-agent technology, which offers the possibility of decentralisation and distributed processing of specified contracts and tenders. The implemented system enables the joint management of orders for a network of small and medium-sized metallurgical plants, while providing them with greater competitiveness and the ability to carry out large procurements. The article presents the functional aspects of the system - the user interface and the principle of operation of individual agents that represent businesses seeking potential suppliers or recipients of services and products. Additionally, the system is equipped with a bi-directional agent translating standards based on ontologies, which aims to automate the decision-making process during tender specifications as a response to the request.

  13. The Use of Some Forecasting Methods and SWOT Analysis in the Selected Processes of Foundry

    Directory of Open Access Journals (Sweden)

    Szymszal J.

    2017-12-01

    Full Text Available Forecasting and analysis SWOT are helping tools in the business activity, because under conditions of dynamic changes in both closer and more distant surroundings, reliable, forward-looking information and trends analysis are playing a decisive role. At present, the ability to use available data in forecasting and other analyzes according with changes in business environment are the key managerial skills required, since both forecasting and SWOT analysis are a integral part of the management process, and the appropriate level of forecasting knowledge is increasingly appreciated. Examples of practical use of some forecasting methods in optimization of the procurement, production and distribution processes in foundries are given. The possibilities of using conventional quantitative forecasting methods based on econometric and adaptive models applying the creep trend and harmonic weights are presented. The econometric models were additionally supplemented with the presentation of error estimation methodology, quality assessment and statistical verification of the forecast. The possibility of using qualitative forecasts based on SWOT analysis was also mentioned.

  14. Tool steels

    DEFF Research Database (Denmark)

    Højerslev, C.

    2001-01-01

    On designing a tool steel, its composition and heat treatment parameters are chosen to provide a hardened and tempered martensitic matrix in which carbides are evenly distributed. In this condition the matrix has an optimum combination of hardness andtoughness, the primary carbides provide...... resistance against abrasive wear and secondary carbides (if any) increase the resistance against plastic deformation. Tool steels are alloyed with carbide forming elements (Typically: vanadium, tungsten, molybdenumand chromium) furthermore some steel types contains cobalt. Addition of alloying elements...... serves primarily two purpose (i) to improve the hardenabillity and (ii) to provide harder and thermally more stable carbides than cementite. Assuming proper heattreatment, the properties of a tool steel depends on the which alloying elements are added and their respective concentrations....

  15. The kingdom of God: Utopian or existential?

    Directory of Open Access Journals (Sweden)

    Gert J. Malan

    2014-06-01

    Full Text Available The kingdom of God was a central theme in Jesus’ vision. Was it meant to be understood as utopian as Mary Ann Beavis views it, or existential? In 1st century CE Palestine, kingdom of God was a political term meaning theocracy suggesting God’s patronage. Jesus used the term metaphorically to construct a new symbolic universe to legitimate a radical new way of living with God in opposition to the temple ideology of exclusivist covenantal nomism. The analogies of father and king served as the root metaphors for this symbolic universe. They are existential root metaphors underpinning the contextual symbolic universe of God’s patronage in reaction to the collapse of the patronage system which left peasants destitute. Jesus’ paradoxical use of the metaphor kingdom of God had a therapeutic value and gave the concept new meaning. The initial motivation for proclaiming God’s patronage originated in Jesus’ primary identity formation by Mary as single parent and was reinforced in his secondary identity formation by John the Baptist. From these results can be concluded that kingdom of God was not meant to be understood as utopian, but existential. In order to clarify the meaning of kingdom of God and God’s patronage for the 21st century, emythologisation and deconstruction can be helpful especially by highlighting the existential meaning of the kingdom of God.

  16. Monitoring of heavy metal particle emission in the exhaust duct of a foundry using LIBS

    International Nuclear Information System (INIS)

    Dutouquet, C.; Le Bihan, O.; Dermigny, A.; Frejafon, E.; Gallou, G.; Sirven, J.B.; Torralba, B.

    2014-01-01

    Heavy metals have long been known to be detrimental to human health and the environment.Their emission is mainly considered to occur via the atmospheric route. Most of airborne heavy metals are of anthropogenic origin and produced through combustion processes at industrial sites such as incinerators and foundries. Current regulations impose threshold limits on heavy metal emissions. The reference method currently implemented for quantitative measurements at exhaust stacks consists of on-site sampling of heavy metals on filters for the particulate phase (the most prominent and only fraction considered in this study) prior to subsequent laboratory analysis. Results are therefore known only a few days after sampling. Stiffer regulations require the development of adapted tools allowing automatic, on-site or even in-situ measurements with temporal resolutions. The Laser-Induced Breakdown Spectroscopy (LIBS) technique was deemed as a potential candidate to meet these requirements. On site experiments were run by melting copper bars and monitoring emission of this element in an exhaust duct at a pilot-scale furnace in a French research center dedicated to metal casting. Two approaches designated as indirect and direct analysis were broached in these experiments. The former corresponds to filter enrichment prior to subsequent LIBS interrogation whereas the latter entails laser focusing right through the aerosol for detection. On-site calibration curves were built and compared with those obtained at laboratory scale in order to investigate possible matrix and analyte effects. Eventually, the obtained results in terms of detection limits and quantitative temporal monitoring of copper emission clearly emphasize the potentialities of the direct LIBS measurements. (authors)

  17. Engineering properties of concrete with partial utilization of used foundry sand.

    Science.gov (United States)

    Manoharan, Thiruvenkitam; Laksmanan, Dhamothiran; Mylsamy, Kaliyannan; Sivakumar, Pandian; Sircar, Anirbid

    2018-01-01

    Solid wastes generated from manufacturing industries are increasing at an alarming rate and it is consistently increasing. One such industrial solid waste is Used Foundry Sand (UFS). On the other hand, fine aggregates involved in the concrete are generally river sand, which is scarce, high cost and excavation of the river sand that promote environmental degradation. So, there is an urge to find some alternative solution to dispose UFS and to limit the use of river sand. In this research work, river sand was partially replaced by UFS. The percentage replacements were 0, 5, 10, 15, 20 and 25 wt% respectively. Experimental investigations were carried out to evaluate the mechanical, durability and micro-structural properties of M20 concrete at the age of 7, 28 and 91 day. XRD (X-ray Diffraction), EDX (Energy Dispersive X-ray) and optical-microscopic imaging analysis were performed to identify the presence of various compounds and micro cracks in the concrete with UFS. Comparative studies on control mix against trial mix were carried out. It was found that compression strength, flexural strength and modulus of elasticity were approximately constant up to 20 wt% UFS and decreased with further addition. Whereas, split tensile strength was increased after 20 wt% addition but it affects the other properties of concrete. The durability test results showed that the resistance of concrete against abrasion and rapid chloride permeability of the concrete mixture containing UFS up to 20 wt% were almost similar to the values of control mix. The findings suggest that UFS can effectively replace river sand. However, it is recommended that the replacement should not exceed 20 wt%. Copyright © 2017. Published by Elsevier Ltd.

  18. Monitoring of heavy metal particle emission in the exhaust duct of a foundry using LIBS.

    Science.gov (United States)

    Dutouquet, C; Gallou, G; Le Bihan, O; Sirven, J B; Dermigny, A; Torralba, B; Frejafon, E

    2014-09-01

    Heavy metals have long been known to be detrimental to human health and the environment. Their emission is mainly considered to occur via the atmospheric route. Most of airborne heavy metals are of anthropogenic origin and produced through combustion processes at industrial sites such as incinerators and foundries. Current regulations impose threshold limits on heavy metal emissions. The reference method currently implemented for quantitative measurements at exhaust stacks consists of on-site sampling of heavy metals on filters for the particulate phase (the most prominent and only fraction considered in this study) prior to subsequent laboratory analysis. Results are therefore known only a few days after sampling. Stiffer regulations require the development of adapted tools allowing automatic, on-site or even in-situ measurements with temporal resolutions. The Laser-Induced Breakdown Spectroscopy (LIBS) technique was deemed as a potential candidate to meet these requirements. On site experiments were run by melting copper bars and monitoring emission of this element in an exhaust duct at a pilot-scale furnace in a French research center dedicated to metal casting. Two approaches designated as indirect and direct analysis were broached in these experiments. The former corresponds to filter enrichment prior to subsequent LIBS interrogation whereas the latter entails laser focusing right through the aerosol for detection. On-site calibration curves were built and compared with those obtained at laboratory scale in order to investigate possible matrix and analyte effects. Eventually, the obtained results in terms of detection limits and quantitative temporal monitoring of copper emission clearly emphasize the potentialities of the direct LIBS measurements. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. Mechanical and toxicological evaluation of concrete artifacts containing waste foundry sand.

    Science.gov (United States)

    Mastella, Miguel Angelo; Gislon, Edivelton Soratto; Pelisser, Fernando; Ricken, Cláudio; da Silva, Luciano; Angioletto, Elídio; Montedo, Oscar Rubem Klegues

    2014-08-01

    The creation of metal parts via casting uses molds that are generally made from sand and phenolic resin. The waste generated after the casting process is called waste foundry sand (WFS). Depending on the mold composition and the casting process, WFS can contain substances that prevent its direct emission to the environment. In Brazil, this waste is classified according to the Standard ABNT NBR 10004:2004 as a waste Class II (Non-Inert). The recycling of this waste is limited because its characteristics change significantly after use. Although the use (or reuse) of this byproduct in civil construction is a technically feasible alternative, its effects must be evaluated, especially from mechanical and environmental points of view. Thus, the objective of this study is to investigate the effect of the use of WFS in the manufacture of cement artifacts, such as masonry blocks for walls, structural masonry blocks, and paving blocks. Blocks containing different concentrations of WFS (up to 75% by weight) were produced and evaluated using compressive strength tests (35 MPa at 28 days) and toxicity tests on Daphnia magna, Allium cepa (onion root), and Eisenia foetida (earthworm). The results showed that there was not a considerable reduction in the compressive strength, with values of 35 ± 2 MPa at 28 days. The toxicity study with the material obtained from leaching did not significantly interfere with the development of D. magna and E. foetida, but the growth of the A. cepa species was reduced. The study showed that the use of this waste in the production of concrete blocks is feasible from both mechanical and environmental points of view. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. Exploring Mission Concepts with the JPL Innovation Foundry A-Team

    Science.gov (United States)

    Ziemer, John K.; Ervin, Joan; Lang, Jared

    2013-01-01

    The JPL Innovation Foundry has established a new approach for exploring, developing, and evaluating early concepts called the A-Team. The A-Team combines innovative collaborative methods with subject matter expertise and analysis tools to help mature mission concepts. Science, implementation, and programmatic elements are all considered during an A-Team study. Methods are grouped by Concept Maturity Level (CML), from 1 through 3, including idea generation and capture (CML 1), initial feasibility assessment (CML 2), and trade space exploration (CML 3). Methods used for each CML are presented, and the key team roles are described from two points of view: innovative methods and technical expertise. A-Team roles for providing innovative methods include the facilitator, study lead, and assistant study lead. A-Team roles for providing technical expertise include the architect, lead systems engineer, and integration engineer. In addition to these key roles, each A-Team study is uniquely staffed to match the study topic and scope including subject matter experts, scientists, technologists, flight and instrument systems engineers, and program managers as needed. Advanced analysis and collaborative engineering tools (e.g. cost, science traceability, mission design, knowledge capture, study and analysis support infrastructure) are also under development for use in A-Team studies and will be discussed briefly. The A-Team facilities provide a constructive environment for innovative ideas from all aspects of mission formulation to eliminate isolated studies and come together early in the development cycle when they can provide the biggest impact. This paper provides an overview of the A-Team, its study processes, roles, methods, tools and facilities.

  1. Correlation between airborne manganese concentration at the workstations in the iron foundry and manganese concentration in workers’ blood

    Directory of Open Access Journals (Sweden)

    Seyedtaghi Mirmohammadi

    2017-08-01

    Full Text Available Background: Manganese (Mn used as raw material for melting process in the ferrous foundry is considered as hazardous neurotoxic substance because it accumulates in the central nervous system and may cause neurological disorders. The furnace-men and melting department workers are potentially exposed to manganese particles or fume in the workplace. The objective of the research has been to investigate the sources and levels of manganese exposure in the foundry by correlation of blood-manganese (B-Mn and air-manganese (air-Mn measurement. Material and Methods: Air-Mn and Mn of blood serum were measured involving workers who worked in a big-sized foundry during 1 year. The standard method of the Occupational Safety and Health Administration (OSHA ID-121 was used for air and blood assessment and atomic absorption spectroscopy (AAS was carried out for air and blood sample analysis. Results: The air sampling results have revealed that there is a high exposure to manganese (4.5 mg/m3 in the workplace as compared to the National Institute for Occupational Safety and Health’s (NIOSH time weighted average (the reference time-weighted average (TWA = 1 mg/m3. The average blood serum Mn concentration was 2.745 μg/l for subjects working for shorter than 3 months and 274.85 μg/l for subjects working 3–12 months. Conclusions: Against the research hypothesis there was no correlation between the air-Mn concentration and the B-Mn (serum level of manganese in the serum of the exposed subjects. It may be due to short time of air sampling of manganese airborne particles, and a real-time monitoring of airborne manganese particles is suggested for any future study. Med Pr 2017;68(4:449–458

  2. Optimization as investment decision support in a Swedish medium-sized iron foundry - A move beyond traditional energy auditing

    International Nuclear Information System (INIS)

    Thollander, Patrik; Mardan, Nawzad; Karlsson, Magnus

    2009-01-01

    Due to increased globalisation, industries are facing greater competition that is pressing companies into decreasing their expenses in order to increase their profits. As regards Swedish industry, it has been faced with substantial increases in energy prices in recent years. Barriers to energy efficiency such as imperfect information inhibit investments in energy efficiency measures, energy audits being one means of reducing barriers and overcoming imperfect information. However, an evaluation of such energy audits in Sweden reveals that it is chiefly low-cost measures that are undertaken as a result of an audit. Moreover, these audits often tend to focus on support processes such as ventilation, lighting, air compressors etc., while measures impacting production processes are often not as extensively covered, which underlines the need for further support in addition to energy audits. Decision support is practised in a variety of different disciplines such as optimization and simulation and the aim of this paper is to explore whether investment decision support practices may be used successfully towards small and medium-sized manufacturers in Sweden when complex production-related investment decisions are taken. The optimization results from the different cases, involving a foundry's investment in a new melting unit, indicate that with no electricity price fluctuations over the day, the investment seems sound as it lowers the overall energy costs. However, with fluctuating electricity prices, there are no large differences in energy costs between the option of retaining the existing five melting furnaces at the foundry and investing in a twin furnace and removing the holding furnaces - which was the initial investment plan for the foundry in the study. It would not have been possible to achieve this outcome without the use of investment decision support such as MIND. One of the main conclusions in this paper is that investment decision support, when strategic

  3. Steel alloys

    International Nuclear Information System (INIS)

    Bloom, E.E.; Stiegler, J.O.; Rowcliffe, A.F.; Leitnaker, J.M.

    1977-01-01

    The invention deals with a fuel element for fast breeder reactors. It consits essentially of a uranium oxide, nitride, or carbide or a mixture of these fuels with a plutonium or thorium oxide, nitride, or carbide. The fuel elements are coated with an austenitic stainless steel alloy. Inside the fuel elements, vacancies or small cavities are produced by neutron effects which causes the steel coating to swell. According to the invention, swelling is prevented by a modification of type 304, 316, 321, or 12 K 72HV commercial steels. They consist mainly of Fe, Cr, and Ni in a ratio determined by a temary diagram. They may also contain 1.8 to 2.3% by weight of Mo and a fraction of Si (0.7 to 2% by weight) and Ti(0.10 to 0.5% by weight) to prevent cavity formation. They are structurally modified by cold working. (IHOE) [de

  4. Energy options in the United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Evans, S C [ed.

    1975-01-01

    The United Kingdom faces two issues: how can it survive the present massive increases in oil prices and the probability of even more expensive supplies in the future or how can it adjust to the eventual exhaustion of both fossil and nuclear fuels. The theme of the symposium concerned a search for a practical alternative source of energy to fossil and nuclear fuels and which ones would work in the United Kingdom. Papers were presented entitled: Geothermal Energy; Solar Energy in Britain; and Wind and Water Sources of Energy in the United Kingdom. A final paper, High- and Low-Growth Scenarios, examined these two types for the future. Many questions, answeres and comments about energy sources are contained in a final presentation. (MCW)

  5. Protist classification and the kingdoms of organisms.

    Science.gov (United States)

    Whittaker, R H; Margulis, L

    1978-04-01

    Traditional classification imposed a division into plant-like and animal-like forms on the unicellular eukaryotes, or protists; in a current view the protists are a diverse assemblage of plant-, animal- and fungus-like groups. Classification of these into phyla is difficult because of their relatively simple structure and limited geological record, but study of ultrastructure and other characteristics is providing new insight on protist classification. Possible classifications are discussed, and a summary classification of the living world into kingdoms (Monera, Protista, Fungi, Animalia, Plantae) and phyla is suggested. This classification also suggests groupings of phyla into superphyla and form-superphyla, and a broadened kingdom Protista (including green algae, oomycotes and slime molds but excluding red and brown algae). The classification thus seeks to offer a compromise between the protist and protoctist kingdoms of Whittaker and Margulis and to combine a full listing of phyla with grouping of these for synoptic treatment.

  6. Characterization and extraction of gold contained in foundry industrial wastes; Caracterizacion y extraccion de oro contenido en matrices de desechos industriales de fundicion

    Energy Technology Data Exchange (ETDEWEB)

    Vite T, J; Vite T, M; Diaz C, A; Carreno de Leon, C [Instituto Nacional de Investigaciones Nucleares, Depto. de Estudios del Ambiente, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1999-07-01

    Gold was characterized and leached in foundry sands. These wastes are product among others of the automotive industry where they are used as molds material which are contaminated by diverse metals during the foundry. To fulfil the leaching process four coupled thermostat columns were used. To characterize the solid it was used the X-ray diffraction technique. For the qualitative analysis it was used the Activation analysis technique. Finally, for the study of liquors was used the Plasma diffraction spectroscopy (Icp-As) technique. The obtained results show that the process which was used the thermostat columns was more efficient, than the methods traditionally recommended. (Author)

  7. Reform of the United Kingdom judicial system

    Directory of Open Access Journals (Sweden)

    Ovidiu-Horia MAICAN

    2013-12-01

    Full Text Available The separation of powers in a state is an essential characteristic of every democratic country, a principle present in many constitutions, most notably that of the United States. The concept is imperfectly fulfilled in the United Kingdom, given that the executive (Ministers form part of the legislature and that part of the judiciary (Law Lords sit in the legislature. As a result, it was necessary to remove the constitutional anomaly that the highest court of appeal in the United Kingdom was situated within one of the chambers of Parliament.

  8. Xeroderma pigmentosum in the United kingdom.

    Science.gov (United States)

    Lehmann, Alan R

    2015-01-01

    The seminal discovery by James Cleaver of defective DNA repair in xeroderma pigmentosum (XP) opened up an ever-expanding field of DNA repair-related disorders. In addition, it put XP on the map and has led to improved diagnosis, care and management of affected patients. In the United Kingdom, we recently established a multidisciplinary specialist clinic for XP patients. All XP patients in the United Kingdom are able to visit the clinic where they are examined and advised by a team of specialists with detailed knowledge of the different aspects of XP. © 2014 The American Society of Photobiology.

  9. Hegelian Steel

    DEFF Research Database (Denmark)

    Kjær, Poul F.

    2015-01-01

    Even in our globalized world the notion of national economies remain incredibly strong, just as a considerable part of the literature on transnational governance and globalization continue to rely on a zero-sum perspective concerning the relationship between the national and the transnational. De...... of the European steel industry....

  10. Calculation of gas release from DC and AC arc furnaces in a foundry

    Science.gov (United States)

    Krutyanskii, M. M.; Nekhamin, S. M.; Rebikov, E. M.

    2016-12-01

    A procedure for the calculation of gas release from arc furnaces is presented. The procedure is based on the stoichiometric ratios of the oxidation of carbon in liquid iron during the oxidation heat period and the oxidation of iron from a steel charge by oxygen in the period of solid charge melting during the gas exchange of the furnace cavity with the external atmosphere.

  11. Property enhancement by grain refinement of zinc-aluminium foundry alloys

    International Nuclear Information System (INIS)

    Krajewski, W K; Piwowarski, G; Krajewski, P K; Greer, A L

    2016-01-01

    Development of cast alloys with good mechanical properties and involving less energy consumption during their melting is one of the key demands of today's industry. Zinc foundry alloys of high and medium Al content, i.e. Zn-(15-30) wt.% Al and Zn-(8-12) wt.% Al, can satisfy these requirements. The present paper summarizes the work [1-9] on improving properties of sand-cast ZnAl10 (Zn-10 wt.% Al) and ZnAl25 (Zn-25 wt. % Al) alloys by melt inoculation. Special attention was devoted to improving ductility, whilst preserving high damping properties at the same time. The composition and structural modification of medium- and high-aluminium zinc alloys influence their strength, tribological properties and structural stability. In a series of studies, Zn - (10-12) wt. % Al and Zn - (25-26) wt.% Al - (1-2.5) wt.% Cu alloys have been doped with different levels of added Ti. The melted alloys were inoculated with ZnTi-based refiners and it was observed that the dendritic structure is significantly finer already after addition of 50 - 100 ppm Ti to the melted alloys. The alloy's structure and mechanical properties have been studied using: SEM (scanning electron microscopy), LM (light microscopy), dilatometry, pin-on-disc wear, and tensile strength measurements. Grain refinement leads to significant improvement of ductility in the binary high-aluminium Zn-(25-27) Al alloys while in the medium-aluminium alloys the effect is rather weak. In the ternary alloys Zn-26Al-Cu, replacing a part of Cu with Ti allows dimensional changes to be reduced while preserving good tribological properties. Furthermore, the high initial damping properties were nearly entirely preserved after inoculation. The results obtained allow us to characterize grain refinement of the examined high-aluminium zinc alloys as a promising process leading to the improvement of their properties. At the same time, using low melting ZnTi-based master alloys makes it possible to avoid the excessive melt

  12. Kingdom of Heaven and its ideological message

    Directory of Open Access Journals (Sweden)

    Yiou Liu

    2017-09-01

    Full Text Available As a Crusades epic, the film Kingdom of Heaven revives the 12th century history in the critical city of Jerusalem. The story surrounds a French blacksmith Balian who defends Jerusalem and contends with the Islamic leader Saladin who attempts to seize back the holy city from the Christians. Through the special themes in region, religion and war, Kingdom of Heaven seems to indicate the conflicts between the East and the West. Furthermore, the outbreaks of 9/11 and the Iraq War definitely make this film’s release more controversial. Kingdom of Heaven, being a film, an essential medium of mass communication, the style in which it expresses its story and ideology is worth considering in depth. By exploring this Hollywood film which lacks of the typical Hollywood style, this paper discusses the significance in making Kingdom of Heaven in the wake of 9/11 and how the critical debate surrounding the film is a reflection of contemporary ideologies.

  13. Radioactive waste management in the United Kingdom

    International Nuclear Information System (INIS)

    Hill, J.

    1976-01-01

    The principles to be followed in the processing and disposal of radioactive wastes are summarized and the procedures practiced in the United Kingdom for different types of wastes are reviewed to illustrate how these principles are being observed. The objectives for the future in modification of current practices are discussed

  14. Cross-kingdom similarities in microbiome functions

    NARCIS (Netherlands)

    Mendes, R.; Raaijmakers, J.M.

    2015-01-01

    Recent advances in medical research have revealed how humans rely on their microbiome for diverse traits and functions. Similarly, microbiomes of other higher organisms play key roles in disease, health, growth and development of their host. Exploring microbiome functions across kingdoms holds

  15. Trans-kingdom cross-talk

    DEFF Research Database (Denmark)

    Knip, Marijn; Constantin, Maria-Ermioni; Thordal-Christensen, Hans

    2014-01-01

    This review focuses on the mobility of small RNA (sRNA) molecules from the perspective of trans-kingdom gene silencing. Mobility of sRNA molecules within organisms is a well-known phenomenon, facilitating gene silencing between cells and tissues. sRNA signals are also transmitted between organism...

  16. NURSING FOR THE KINGDOM OF GOD.

    Science.gov (United States)

    Eckerd, Nancy A

    2015-01-01

    The importance of nursing as Christ would is vital for Christian nurses. At one Christian school of nursing, students are taught the concept of Kingdom Nursing: focused, dynamic, patient-centered care, inspired by the qualities of Christ and influenced by the presence of the Holy Spirit in the life of the nurse.

  17. Antimicrobial Drugs in the Home, United Kingdom

    OpenAIRE

    McNulty, Cliodna A.M.; Boyle, Paul; Nichols, Tom; Clappison, Douglas P.; Davey, Peter

    2006-01-01

    A total of 6% of 6,983 households in the United Kingdom had leftover antimicrobial drugs, and 4% had standby antimicrobial drugs. Respondents with leftover drugs were more educated, more knowledgeable about antimicrobial drugs, younger, and female. Of respondents with leftover drugs, 44% kept them in case of future need, and 18% had taken these drugs without medical advice.

  18. Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

    Directory of Open Access Journals (Sweden)

    Nirmala D.B.

    2016-06-01

    Full Text Available This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37 Orthogonal Arrays (OA with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering “Nominal the better” situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

  19. Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

    Science.gov (United States)

    Nirmala, D. B.; Raviraj, S.

    2016-06-01

    This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC) containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37) Orthogonal Arrays (OA) with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering "Nominal the better" situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

  20. Correlation between work process-related exposure to polycyclic aromatic hydrocarbons and urinary levels of alpha-naphthol, beta-naphthylamine and 1-hydroxypyrene in iron foundry workers

    DEFF Research Database (Denmark)

    Hansen, Åse Marie; Omland, Øyvind; Poulsen, O M

    1994-01-01

    foundry workers. Hand molders, finishing workers and truck drivers tended to have the highest levels. Concerning alpha-naphthol the highest concentrations were measured in urine from casters and shake-out workers. With regard to epidemiologic studies demonstrating that molders and casters have a higher...

  1. Lung cancer risk in welders and foundry workers with a history of heavy smoking in the USA: The National Lung Screening Trial.

    Science.gov (United States)

    Wong, Jason Y Y; Bassig, Bryan A; Seow, Wei Jie; Hu, Wei; Ji, Bu-Tian; Blair, Aaron; Silverman, Debra T; Lan, Qing

    2017-06-01

    Foundry work is a risk factor for lung cancer; however, the association with welding is unclear, as smoking is common among metalworkers and may mask the relationship. We evaluated whether history of welding and foundry work, independently and jointly, and employment duration were associated with lung cancer risk in heavy smokers. We analysed data from the National Lung Screening Trial, a prospective randomised trial of 53 454 heavy smokers (>30 pack-years) in the USA. Cox regression models were used to estimate the HRs and 95% CIs of medically/histologically confirmed incident lung cancer during the follow-up period (2002-2009) in relation to history and duration of welding and foundry work assessed via questionnaires, adjusted for screening arm, component study, sex, age, race/ethnicity, education, smoking status and pack-years, body mass index and personal/family medical history. There were 2034 incident lung cancer cases throughout the follow-up. Increasing years of employment in welding (p-trend =0.039) and foundry work (p-trend =0.005) were related to increased lung cancer risk among heavy smokers. Having ever been employed (≥1 yr) as either a welder or foundry worker alone was associated with non-significant increased risks of lung cancer (HR=1.12 (95% CI 0.91 to 1.37) and HR=1.09 (95% CI 0.85 to 1.39), respectively). Further, there was a joint-effect in that those who were ever employed in both occupations had significantly increased risks (HR=1.48 (95% CI 1.08 to 2.04)). Our findings provide further evidence that exposure to welding/metal fumes may be associated with elevated lung cancer risk. NCT00047385. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  2. Use of Solid Waste (Foundry Slag) Mortar and Bamboo Reinforcement in Seismic Analysis for Single Storey Masonry Building

    Science.gov (United States)

    Ahmad, S.; Husain, A.; Ghani, F.; Alam, M. N.

    2013-11-01

    The conversion of large amount of solid waste (foundry slag) into alternate source of building material will contribute not only as a solution to growing waste problem, but also it will conserve the natural resources of other building material and thereby reduce the cost of construction. The present work makes an effort to safe and economic use of recycle mortar (1:6) as a supplementary material. Conventional and recycled twelve prisms were casted with varying percentage of solid waste (foundry slag) added (0, 10, 20, 30 %) replacing cement by weight and tested under compression testing machine. As the replacement is increasing, the strength is decreasing. 10 % replacement curve is very closed to 0 % whereas 20 % is farther and 30 % is farthest. 20 % replacement was chosen for dynamic testing as its strength is within permissible limit as per IS code. A 1:4 scale single storey brick model with half size brick was fabricated on shake table in the lab for dynamic testing using pure friction isolation system (coarse sand as friction material µ = 0.34). Pure friction isolation technique can be adopted economically in developing countries where low-rise building prevails due to their low cost. The superstructure was separated from the foundation at plinth level, so as to permit sliding of superstructure during severe earthquake. The observed values of acceleration and displacement responses compare fairly with the analytical values of the analytical model. It also concluded that 20 % replacement of cement by solid waste (foundry slag) could be safely adopted without endangering the safety of the masonry structures under seismic load.To have an idea that how much energy is dissipated through this isolation, the same model with fixed base was tested and results were compared with the isolated free sliding model and it has been observed that more than 60 % energy is dissipated through this pure friction isolation technique. In case of base isolation, no visible cracks

  3. The nuclear energy in the United Kingdom

    International Nuclear Information System (INIS)

    2006-02-01

    With challenges like the climatic change, the hydrocarbons prices increase and the energy supply security, the nuclear park is becoming a decisive and an urgent question in the United Kingdom. The author proposes an historical aspect of the nuclear energy in UK, the actors of the today nuclear industry and the technologies used in 2006, the radioactive wastes management, the programs of the future and the british opinion on the nuclear. (A.L.B.)

  4. United Kingdom government policy towards radioactive waste

    International Nuclear Information System (INIS)

    Pritchard, G.

    1986-01-01

    There are three areas of radioactive waste management which exemplify, beyond any reasonable doubt, that the United Kingdom has in the past (and intends in the future), to pursue a policy of dispersal and disposal of radioactive wastes: These are: (I) dumping of low-level waste in the deep ocean and, on a parallel, seabed emplacement of highly active waste; (II) the liquid discharges from Windscale into the Irish Sea; and (III) land dumping of low- and intermediate-level waste

  5. Monolithic silicon photonics in a sub-100nm SOI CMOS microprocessor foundry: progress from devices to systems

    Science.gov (United States)

    Popović, Miloš A.; Wade, Mark T.; Orcutt, Jason S.; Shainline, Jeffrey M.; Sun, Chen; Georgas, Michael; Moss, Benjamin; Kumar, Rajesh; Alloatti, Luca; Pavanello, Fabio; Chen, Yu-Hsin; Nammari, Kareem; Notaros, Jelena; Atabaki, Amir; Leu, Jonathan; Stojanović, Vladimir; Ram, Rajeev J.

    2015-02-01

    We review recent progress of an effort led by the Stojanović (UC Berkeley), Ram (MIT) and Popović (CU Boulder) research groups to enable the design of photonic devices, and complete on-chip electro-optic systems and interfaces, directly in standard microelectronics CMOS processes in a microprocessor foundry, with no in-foundry process modifications. This approach allows tight and large-scale monolithic integration of silicon photonics with state-of-the-art (sub-100nm-node) microelectronics, here a 45nm SOI CMOS process. It enables natural scale-up to manufacturing, and rapid advances in device design due to process repeatability. The initial driver application was addressing the processor-to-memory communication energy bottleneck. Device results include 5Gbps modulators based on an interleaved junction that take advantage of the high resolution of the sub-100nm CMOS process. We demonstrate operation at 5fJ/bit with 1.5dB insertion loss and 8dB extinction ratio. We also demonstrate the first infrared detectors in a zero-change CMOS process, using absorption in transistor source/drain SiGe stressors. Subsystems described include the first monolithically integrated electronic-photonic transmitter on chip (modulator+driver) with 20-70fJ/bit wall plug energy/bit (2-3.5Gbps), to our knowledge the lowest transmitter energy demonstrated to date. We also demonstrate native-process infrared receivers at 220fJ/bit (5Gbps). These are encouraging signs for the prospects of monolithic electronics-photonics integration. Beyond processor-to-memory interconnects, our approach to photonics as a "More-than- Moore" technology inside advanced CMOS promises to enable VLSI electronic-photonic chip platforms tailored to a vast array of emerging applications, from optical and acoustic sensing, high-speed signal processing, RF and optical metrology and clocks, through to analog computation and quantum technology.

  6. The kingdom of heaven and Matthew 10

    Directory of Open Access Journals (Sweden)

    Jacob J. Scholtz

    2014-08-01

    Full Text Available This article proposes that the mission discourse in Matthew 10 is a single mission assignment that covers two distinct time periods when the gospel of the kingdom is preached. This assignment commenced during Christ’s first advent when the 12 apostles preached the gospel of the kingdom only in Israel. However, as a result of ‘this generation’ committing the unpardonable sin, this assignment became postponed until it will be resumed in the Tribulation when the coming King will authorise Jewish messengers to preach the gospel of the kingdom again – this time as a witness to all the nations. Based on this view of the mission discourse in Matthew 10, this article proposes a chiastic structure for Matthew 9:36−11:1a. Each section of this text will then be briefly discussed. Although the Church can make applications from this discourse, it is argued that Matthew 10:5b−42 does not refer to the Church age.

  7. A living foundry for Synthetic Biological Materials: A synthetic biology roadmap to new advanced materials.

    Science.gov (United States)

    Le Feuvre, Rosalind A; Scrutton, Nigel S

    2018-06-01

    Society is on the cusp of harnessing recent advances in synthetic biology to discover new bio-based products and routes to their affordable and sustainable manufacture. This is no more evident than in the discovery and manufacture of Synthetic Biological Materials , where synthetic biology has the capacity to usher in a new Materials from Biology era that will revolutionise the discovery and manufacture of innovative synthetic biological materials. These will encompass novel, smart, functionalised and hybrid materials for diverse applications whose discovery and routes to bio-production will be stimulated by the fusion of new technologies positioned across physical, digital and biological spheres. This article, which developed from an international workshop held in Manchester, United Kingdom, in 2017 [1], sets out to identify opportunities in the new materials from biology era. It considers requirements, early understanding and foresight of the challenges faced in delivering a Discovery to Manufacturing Pipeline for synthetic biological materials using synthetic biology approaches. This challenge spans the complete production cycle from intelligent and predictive design, fabrication, evaluation and production of synthetic biological materials to new ways of bringing these products to market. Pathway opportunities are identified that will help foster expertise sharing and infrastructure development to accelerate the delivery of a new generation of synthetic biological materials and the leveraging of existing investments in synthetic biology and advanced materials research to achieve this goal.

  8. A living foundry for Synthetic Biological Materials: A synthetic biology roadmap to new advanced materials

    Directory of Open Access Journals (Sweden)

    Rosalind A. Le Feuvre

    2018-06-01

    Full Text Available Society is on the cusp of harnessing recent advances in synthetic biology to discover new bio-based products and routes to their affordable and sustainable manufacture. This is no more evident than in the discovery and manufacture of Synthetic Biological Materials, where synthetic biology has the capacity to usher in a new Materials from Biology era that will revolutionise the discovery and manufacture of innovative synthetic biological materials. These will encompass novel, smart, functionalised and hybrid materials for diverse applications whose discovery and routes to bio-production will be stimulated by the fusion of new technologies positioned across physical, digital and biological spheres. This article, which developed from an international workshop held in Manchester, United Kingdom, in 2017 [1], sets out to identify opportunities in the new materials from biology era. It considers requirements, early understanding and foresight of the challenges faced in delivering a Discovery to Manufacturing Pipeline for synthetic biological materials using synthetic biology approaches. This challenge spans the complete production cycle from intelligent and predictive design, fabrication, evaluation and production of synthetic biological materials to new ways of bringing these products to market. Pathway opportunities are identified that will help foster expertise sharing and infrastructure development to accelerate the delivery of a new generation of synthetic biological materials and the leveraging of existing investments in synthetic biology and advanced materials research to achieve this goal. Keywords: Synthetic biology, Materials, Biological materials, Biomaterials, Advanced materials

  9. Corrosion resistant steel

    International Nuclear Information System (INIS)

    Zubchenko, A.S.; Borisov, V.P.; Latyshev, V.B.

    1980-01-01

    Corrosion resistant steel for production of sheets and tubes containing C, Mn, Cr, Si, Fe is suggested. It is alloyed with vanadium and cerium for improving tensile properties and ductility. The steel can be melted by a conventional method in electric-arc or induction furnaces. The mentioned steel is intended to be used as a substitute for nickel-bearing austenitic steels

  10. Plasma nitriding of steels

    CERN Document Server

    Aghajani, Hossein

    2017-01-01

    This book focuses on the effect of plasma nitriding on the properties of steels. Parameters of different grades of steels are considered, such as structural and constructional steels, stainless steels and tools steels. The reader will find within the text an introduction to nitriding treatment, the basis of plasma and its roll in nitriding. The authors also address the advantages and disadvantages of plasma nitriding in comparison with other nitriding methods. .

  11. Environmental characterization foundry sands used in sanitary landfills; Caracterizacao ambiental de areias descartadas de fundicao utilizadas na cobertura de residuos em aterros sanitarios

    Energy Technology Data Exchange (ETDEWEB)

    Domingues, L.G.F.; Ferreira, G.C.S.; Pires, M.S.G.; Teixeira, I.; Carnin, R.; Sarro, W.S., E-mail: lucienegferrari@gmail.com [Universidade Estadual de Campinas (UNICAMP), SP (Brazil)

    2016-07-01

    The national solid waste policy recommends reducing solid waste generation and reusing them in different applications. Preliminary studies show that the foundry sand generated from cast metal parts undercut, has excellent applicability in grain size stabilization of soils for geotechnical functions, and therefore, should not be discarded as waste. This study aimed at environmental characterization of two lots of waste foundry sand (WFS), from different industries, to the particle size stabilization of a clayey soil for use in coverage of solid waste in landfills. The methodology included physicochemical characterization tests (grain size, permeability, XRF and heavy metals) and environmental (NBR 10004: 2004, NBR 10005: 2004, NBR 10006: 20004 and acute toxicity with Vibrio fischeri). The results prove the environmental viability of using these lots of WFS as functional material in the composition of landfills. (author)

  12. Nuclear safety philosophy in the United Kingdom

    International Nuclear Information System (INIS)

    Anthony, R.D.

    1986-01-01

    Development of the United Kingdom (UK) nuclear safety philosophy is described in the context of the UK nuclear power program since 1959 and of its legislative framework. Basic to the philosophy is that the licensee is wholly responsible for nuclear safety. The licensing process and safety assessment principles used by the Nuclear Installations Inspectorate are discussed, and examples from the assessment of the proposed UK pressurized-water reactor are used to illustrate how the approach works in practice. The UK siting policy and regulatory developments since 1979 are also discussed. Recent, current, and future issues of interest to the regulatory authority are described against the development nuclear scene in the UK

  13. Alpha spectrometric characterization of process-related particle size distributions from active particle sampling at the Los Alamos National Laboratory uranium foundry

    Energy Technology Data Exchange (ETDEWEB)

    Plionis, Alexander A [Los Alamos National Laboratory; Peterson, Dominic S [Los Alamos National Laboratory; Tandon, Lav [Los Alamos National Laboratory; Lamont, Stephen P [Los Alamos National Laboratory

    2009-01-01

    Uranium particles within the respirable size range pose a significant hazard to the health and safety of workers. Significant differences in the deposition and incorporation patterns of aerosols within the respirable range can be identified and integrated into sophisticated health physics models. Data characterizing the uranium particle size distribution resulting from specific foundry-related processes are needed. Using personal air sampling cascade impactors, particles collected from several foundry processes were sorted by activity median aerodynamic diameter onto various Marple substrates. After an initial gravimetric assessment of each impactor stage, the substrates were analyzed by alpha spectrometry to determine the uranium content of each stage. Alpha spectrometry provides rapid nondestructive isotopic data that can distinguish process uranium from natural sources and the degree of uranium contribution to the total accumulated particle load. In addition, the particle size bins utilized by the impactors provide adequate resolution to determine if a process particle size distribution is: lognormal, bimodal, or trimodal. Data on process uranium particle size values and distributions facilitate the development of more sophisticated and accurate models for internal dosimetry, resulting in an improved understanding of foundry worker health and safety.

  14. The 1986 United Kingdom radioactive waste inventory

    International Nuclear Information System (INIS)

    Shepherd, J.; Harrison, J.; McNicholas, P.

    1987-11-01

    This report gives information on the radioactive wastes which arise in the United Kingdom, updated to 1 January 1986. It has been compiled from information provided by the principal producers of the wastes, Amersham International plc, British Nuclear Fuels plc, the Central Electricity Generating Board, the South of Scotland Electricity Board, and the United Kingdom Atomic Energy Authority. The report lists the waste types, or streams, which these organisations produce, or will produce, as part of their normal operations or from decommissioning of their plant. For each stream is given the volume (or in a few cases mass) of existing stocks, estimated arisings to the year 2030 (2080 in the case of some decommissioning wastes), specific activity, and conditioning factor (volume change from ''raw'' waste volume to volume conditioned for disposal). Details of the radionuclide compositions of individual waste streams are separately listed. Waste streams are allocated to one of the three categories High, Intermediate or Low-Level, although this does not necessarily imply any commitment to a particular disposal route. The report includes tables summarising the data, arranged in a hierarchical manner to enable totals to be readily extracted as required. Summary tables of both ''raw'' and ''conditioned'' waste volumes are given. Also included are a commentary on the data and important changes from the 1985 inventory, and information on scenarios on which estimates of future arisings are based. (author)

  15. Paper recycling and social policy. [United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Turner, R K; Grace, R

    1976-12-01

    The most promising new source of paper for recycling is the household and small commercial business, whose waste papers can be processed if the paper and board industry is willing to invest capital to develop the facilities and the technology needed to upgrade indigenous fibers. Cost-benefit analyses in the United Kingdom indicate that support of this type of paper recycling has more merit than a buffer stock scheme. Efforts to conserve virgin materials by increasing the use of secondary materials could be further strengthened by taxes on the disposal of virgin materials. Paper recycling policies should include a range of sources, from discarded post-consumer waste paper and boxes to the release and use of energy by incineration, pyrolysis, and hydrolysis. Waste availability is influenced by product durability, replacement by other products (such as plastic wrap for paper), industry maturity, and social attitudes. Public acceptance of lower-quality paper products and improved technology to remove ink and color should combine to make recycling more feasible. Efforts to develop the household and commercial sector will result in lower import requirements for wood pulp and an improved balance of payments for the United Kingdom. Recycled fibers require less water and energy to process, but the process wastes introduce environmental pollutants. Short- and long-term forecasts show a growth rate trend that varies with paper grade and corresponds with general economic growth. (35 references) (DCK)

  16. Energy options for the United Kingdom

    International Nuclear Information System (INIS)

    Warner, P.C.

    1979-03-01

    The purpose of this paper is to put together a picture of the energy policy options of the United Kingdom, drawn mainly from official documents but supplemented by comments and conclusions from the author. For some people the current energy debate is simplified down to nuclear power for and against. Much of this thinking seems to arise from misunderstanding, and the more the technical and social facts behind policy can be sorted out by discussions, the more sensible eventual policy will be. One extreme view, for instance, is that opinion is divided between those who are 'pro-industry, pro-production, and pro-nuclear' and those who are 'interested in ecology and therefore anti-nuclear.' Associations like those are high on the list of myths that need to be dispelled. It is therefore a further purpose of this paper to contribute to the general background of facts for those who are interested in this country's energy policies and who may not have time or the opportunity to work through original sources. Although the theme throughout is energy in the United Kingdom, it will be realised that extension to the world scale simply enhances shortages and problems. The paper is in sections, entitled: overall UK energy consumption; coal; oil; gas; the energy gap; alternative energy sources; the balance of primary resource need; electricity; the nuclear power programme; timing of power plant orders; conclusions. (U.K.)

  17. How Many Kingdoms? Current Views of Biological Classification.

    Science.gov (United States)

    Margulis, Lynn

    1981-01-01

    Argues for the acceptance and use of a five-kingdom classification system for biology comprised of monera, protoctista, fungi, animals, and plants. Justifies the new system based upon the difference between prokaryotes and eukaryotes. Outlines each kingdom and describes its members. (DC)

  18. The kingdom of heaven and Matthew 10

    Directory of Open Access Journals (Sweden)

    Jacob J. Scholtz

    2014-08-01

    Full Text Available This article proposes that the mission discourse in Matthew 10 is a single mission assignment that covers two distinct time periods when the gospel of the kingdom is preached. This assignment commenced during Christ’s first advent when the 12 apostles preached the gospel of the kingdom only in Israel. However, as a result of ‘this generation’ committing the unpardonable sin, this assignment became postponed until it will be resumed in the Tribulation when the coming King will authorise Jewish messengers to preach the gospel of the kingdom again – this time as a witness to all the nations. Based on this view of the mission discourse in Matthew 10, this article proposes a chiastic structure for Matthew 9:36−11:1a. Each section of this text will then be briefly discussed. Although the Church can make applications from this discourse, it is argued that Matthew 10:5b−42 does not refer to the Church age. Die koninkryk van die hemele en Matteus 10. Hierdie artikel bespreek die sendingdiskoers in Matteus 10 en beweer dat dit ’n enkele sendingopdrag is wat twee diskrete tydperiodes dek wanneer die evangelie van die koninkryk verkondig is. Hierdie sendingopdrag is tydens Christus se eerste koms aan die 12 apostels gegee om die evangelie van die koninkryk net in Israel te verkondig. Omdat ‘hierdie geslag’ die onvergeeflike sonde gedoen het, is hierdie sendingopdrag uitgestel en sal hervat word tydens die Verdrukking wanneer die komende Koning Joodse boodskappers sal magtig om weer die evangelie van die koninkryk te verkondig – hierdie keer tot getuienis vir al die nasies. Hierdie artikel stel ’n chiastiese struktuur vir Matteus 9:36−11:1a voor wat gebaseer is op hierdie siening van die sendingdiskoers in Matteus 10. Daarna word elke afdeling van die teks kortliks bespreek. Alhoewel die Kerk toepassings uit hierdie diskoers kan maak, word geargumenteer dat Matteus 10:5b−42 nie na die Kerk-era verwys nie.

  19. Evaluation of Synthetic Gypsum Recovered via Wet Flue-Gas Desulfurization from Electric Power Plants for Use in Foundries

    Directory of Open Access Journals (Sweden)

    R. Biernacki

    2012-09-01

    Full Text Available This article investigates possible use of waste gypsum (synthetic, recovered via flue-gas desulfurization from coal-fired electric powerplants, in foundries. Energy sector, which in Eastern Europe is mostly composed from coal-fired electric power plants, is one of the largestproducers of sulfur dioxide (SO2.In order to protect the environment and reduce the amount of pollution flue-gas desulfurization (FGD is used to remove SO2 fromexhaust flue gases of fossil-fuel power plants. As a result of this process gypsum waste is produced that can be used in practicalapplications.Strength and permeability tests have been made and also in-depth analysis of energy consumption of production process to investigateways of preparing the synthetic gypsum for casting moulds application. This paper also assesses the chemical composition, strength andpermeability of moulds made with synthetic gypsum, in comparison with moulds made with traditional GoldStar XL gypsum and withceramic molds. Moreover examination of structure of synthetic gypsum, the investigations on derivatograph and calculations of energyconsumption during production process of synthetic gypsum in wet flue-gas desulfurization were made.After analysis of gathered data it’s possible to conclude that synthetic gypsum can be used as a material for casting mould. There is nosignificant decrease in key properties, and on the other hand there is many additional benefits including low energy consumption,decreased cost, and decreased environmental impact.

  20. Declining metal levels at Foundry Cove (Hudson River, New York): Response to localized dredging of contaminated sediments

    International Nuclear Information System (INIS)

    Mackie, Joshua A.; Natali, Susan M.; Levinton, Jeffrey S.; Sanudo-Wilhelmy, Sergio A.

    2007-01-01

    This study examines the effectiveness of remediating a well-recognized case of heavy metal pollution at Foundry Cove (FC), Hudson River, New York. This tidal freshwater marsh was polluted with battery-factory wastes (1953-1979) and dredged in 1994-1995. Eight years after remediation, dissolved and particulate metals (Cd, Co, Cu, Pb, Ni, and Ag) were found to be lower than levels in the lower Hudson near New York City. Levels of metals (Co, Ni, Cd) on suspended particles were comparatively high. Concentrations of surface sediment Cd throughout the marsh system remain high, but have decreased both in the dredged and undredged areas: Cd was 2.4-230 mg/kg dw of sediment in 2005 vs. 109-1500 mg/kg in the same area in 1983. The rate of tidal export of Cd from FC has decreased by >300-fold, suggesting that dredging successfully stemmed a major source of Cd to the Hudson River. - Dredging of a hotspot of metal-contaminated sediment is associated with a recognizable local and river-wide decline in cadmium in the Hudson River, New York

  1. Conditions of Thermal Reclamation Process Realization on a Sample of Spent Moulding Sand from an Aluminum Alloy Foundry Plant

    Directory of Open Access Journals (Sweden)

    Łucarz M.

    2017-06-01

    Full Text Available The results of investigations of thermal reclamation of spent moulding sands originating from an aluminum alloy foundry plant are presented in this paper. Spent sands were crushed by using two methods. Mechanical fragmentation of spent sand chunks was realized in the vibratory reclaimer REGMAS. The crushing process in the mechanical device was performed either with or without additional crushing-grinding elements. The reclaimed material obtained in this way was subjected to thermal reclamations at two different temperatures. It was found that a significant binder gathering on grain surfaces favors its spontaneous burning, even in the case when a temperature lower than required for the efficient thermal reclamation of furan binders is applied in the thermal reclaimer. The burning process, initiated by gas burners in the reclaimer chamber, generates favorable conditions for self-burning (at a determined amount of organic binders on grain surfaces. This process is spontaneously sustained and decreases the demand for gas. However, due to the significant amount of binder, this process is longer than in the case of reclaiming moulding sand prepared with fresh components.

  2. Using mixture design of experiments to assess the environmental impact of clay-based structural ceramics containing foundry wastes

    Energy Technology Data Exchange (ETDEWEB)

    Coronado, M. [Department of Chemistry and Process and Resources Engineering, University of Cantabria, 39005 Santander (Spain); Department of Materials and Ceramics Engineering (CICECO), University of Aveiro, 3810-193 Aveiro (Portugal); Segadães, A.M. [Department of Materials and Ceramics Engineering (CICECO), University of Aveiro, 3810-193 Aveiro (Portugal); Andrés, A., E-mail: andresa@unican.es [Department of Chemistry and Process and Resources Engineering, University of Cantabria, 39005 Santander (Spain)

    2015-12-15

    Highlights: • Modelling of the environmental risk in terms of clay and by-products contents. • M-DoE and response surface plots enable quick comparison of three ceramic processes. • Basicity of the mixture increases the leaching, especially at low firing temperatures. • Liquid phase content plays a major role decreasing the leaching of Cr and Mo. • Together, M-DoE and phase diagrams enable better prediction of pollutants leaching. - Abstract: This work describes the leaching behavior of potentially hazardous metals from three different clay-based industrial ceramic products (wall bricks, roof tiles, and face bricks) containing foundry sand dust and Waelz slag as alternative raw materials. For each product, ten mixtures were defined by mixture design of experiments and the leaching of As, Ba, Cd, Cr, Cu, Mo, Ni, Pb, and Zn was evaluated in pressed specimens fired simulating the three industrial ceramic processes. The results showed that, despite the chemical, mineralogical and processing differences, only chrome and molybdenum were not fully immobilized during ceramic processing. Their leaching was modeled as polynomial equations, functions of the raw materials contents, and plotted as response surfaces. This brought to evidence that Cr and Mo leaching from the fired products is not only dependent on the corresponding contents and the basicity of the initial mixtures, but is also clearly related with the mineralogical composition of the fired products, namely the amount of the glassy phase, which depends on both the major oxides contents and the firing temperature.

  3. Optimising a Model of Minimum Stock Level Control and a Model of Standing Order Cycle in Selected Foundry Plant

    Directory of Open Access Journals (Sweden)

    Szymszal J.

    2013-09-01

    Full Text Available It has been found that the area where one can look for significant reserves in the procurement logistics is a rational management of the stock of raw materials. Currently, the main purpose of projects which increase the efficiency of inventory management is to rationalise all the activities in this area, taking into account and minimising at the same time the total inventory costs. The paper presents a method for optimising the inventory level of raw materials under a foundry plant conditions using two different control models. The first model is based on the estimate of an optimal level of the minimum emergency stock of raw materials, giving information about the need for an order to be placed immediately and about the optimal size of consignments ordered after the minimum emergency level has occurred. The second model is based on the estimate of a maximum inventory level of raw materials and an optimal order cycle. Optimisation of the presented models has been based on the previously done selection and use of rational methods for forecasting the time series of the delivery of a chosen auxiliary material (ceramic filters to a casting plant, including forecasting a mean size of the delivered batch of products and its standard deviation.

  4. The assessment of impact on nuclear power plant structures in the United Kingdom

    International Nuclear Information System (INIS)

    Fullard, K.; Baum, M.R.

    1991-01-01

    Impact research in the United Kingdom has embraced a wide range of topics during the last fifteen years and advice has been provided in the form of guidelines for use in safety assessments and design studies. It is now the intention to produce a comprehensive Impact Assessment Procedure encompassing the definition of loading, whipping pipe effects and the response of steel and concrete targets. This paper is restricted to introducing the methods used for characterising missiles from pressurised vessels and for determining the impact damage produced in concrete targets. Considerable reliance has been placed on the interpretation of experimental data and guidance is therefore limited by the availability of such data. This paper indicates the extent to which advice can be given and the issues which still need further attention. An example is given of the use of the methods for characterising missiles from a cylindrical pressure vessel. (orig.)

  5. Corollary discharge across the animal kingdom.

    Science.gov (United States)

    Crapse, Trinity B; Sommer, Marc A

    2008-08-01

    Our movements can hinder our ability to sense the world. Movements can induce sensory input (for example, when you hit something) that is indistinguishable from the input that is caused by external agents (for example, when something hits you). It is critical for nervous systems to be able to differentiate between these two scenarios. A ubiquitous strategy is to route copies of movement commands to sensory structures. These signals, which are referred to as corollary discharge (CD), influence sensory processing in myriad ways. Here we review the CD circuits that have been uncovered by neurophysiological studies and suggest a functional taxonomic classification of CD across the animal kingdom. This broad understanding of CD circuits lays the groundwork for more challenging studies that combine neurophysiology and psychophysics to probe the role of CD in perception.

  6. Some thoughts from the United Kingdom

    International Nuclear Information System (INIS)

    Lynn, N.M.

    2001-01-01

    The UK Atomic Energy Authority has three research centres and many industrial enterprises. However, there is a general decline/stagnation of activities with only one research reactor for civilian use and no growth in the nuclear power sector. The United Kingdom may soon face the shortage of personnel in the essential field like health physics, radiation protection and safety management. Also there is a concern about anti-nuclear culture which is growing roots. British Nuclear Fuels Limited is trying to address some of these problems by opening a visitor centre in Sellafield and a centre of excellence in radiochemistry in one of the universities. International collaboration among nuclear research centres would be very valuable for optimizing the use of research reactors, training of nuclear engineers, decommissioning and handling other related issues. (author)

  7. Renewable Energy Policy Fact sheet - United Kingdom

    International Nuclear Information System (INIS)

    2017-07-01

    The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. In the United Kingdom RES-E are supported through a feed-in tariff, Contracts for Difference scheme, a quota system and tax regulation mechanism. For RES-H and C a subsidy and price-based mechanisms are available for supporting RES-H installations. Furthermore, a quota system for biofuels and a grant scheme for transport is in place. A training programme for RES-E plant installers is in place, as well as a certification programme for RES-E installations. An overarching Renewable Energy Roadmap relating to RES-E has been laid down and implemented

  8. Is the Kingdom of Bicycles Rising Again?

    DEFF Research Database (Denmark)

    Rømer Christensen, Hilda

    2017-01-01

    This article focuses on new types of cycling in postsocialist China, especially mountain and sports biking, and on the particular entanglements of gender and class brought with them. The shift in mobility and biking from the Mao era to the postsocialist China is analyzed in the contexts of cultural......-analytical notions of global assemblages and gendered interpellations. Based on Chinese newspaper materials and fieldwork in Beijing and Shanghai, the article examines the social and gendered implications of the new biking cultures. These new biking practices mainly interpellate new middle-class men...... and masculinities as part of an exclusive leisure culture. If the “Kingdom of the Bicycles” is going to rise again, there is a need for a broader scope that addresses access for all, including women and families, as smart bikers, as well as biking as a daily mode of transportation....

  9. Energy from the wind. [For United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Musgrove, P J

    1977-01-01

    An assessment is made of the amount of power/energy in the wind with emphasis on calculations for the United Kingdom. Windmills must be deployed over a given area in a pattern that takes account of the distribution of directions from which the wind can be expected. In the U.K., one such array can be provided in the Western Isles. The author recommends deploying such an array in the shallow waters of the southern North Sea. He concludes that deploying such an array in the shallow offshore region would have the potential for providing a very significant part of the total electricity requirements. He also concludes that such a wind-power system appears competitive with nuclear power systems. 8 references. (MCW)

  10. Spinal Motocross Injuries in the United Kingdom.

    Science.gov (United States)

    Singh, Rohit; Bhalla, Amit; Ockendon, Matthew; Hay, Stuart

    2018-01-01

    Motocross is a form of motorcycle racing held on established off-road circuits and has been a recreational and competitive sport across the world for >100 years. In the United Kingdom alone, motocross has grown into a phenomenally ambitious and popular franchise. There are >200 motocross clubs across the country, permitting >900 events annually. To assess the current trend of spine-related motocross injuries over the past 5 years. Descriptive epidemiology study. Data were prospectively collected over 5 years (August 2010-August 2015) at our regional trauma and spine unit, regardless of whether the rider was performing the sport competitively or recreationally. During the study period, spine-related injuries were identified for 174 patients (age range, 6-75 years) who were directly referred to our department following recreational or competitive motocross, with most injuries being sustained within the early spring and summer months, representing the start of the motocross season. A significant number of injuries were in males (n = 203, 94%), with the majority of injuries occurring within the 21- to 30-year-old age group. A total of 116 (54%) injuries required operative treatment. The most common spinal injury was thoracolumbar burst fracture (n = 95), followed by chance fractures (n = 26). This data series emphasizes the prevalence and devastation of motocross-related spinal injuries in the United Kingdom and may serve in administering sanctions and guidelines to governing bodies of motocross. The spinal injuries that occur during motocross have significant capital connotations for regional spinal centers. The recent surge in motocross popularity is correlated with the number of injuries, which have increased over the past 5 years by almost 500%.

  11. Spinal Motocross Injuries in the United Kingdom

    Science.gov (United States)

    Singh, Rohit; Bhalla, Amit; Ockendon, Matthew; Hay, Stuart

    2018-01-01

    Background: Motocross is a form of motorcycle racing held on established off-road circuits and has been a recreational and competitive sport across the world for >100 years. In the United Kingdom alone, motocross has grown into a phenomenally ambitious and popular franchise. There are >200 motocross clubs across the country, permitting >900 events annually. Purpose: To assess the current trend of spine-related motocross injuries over the past 5 years. Study Design: Descriptive epidemiology study. Methods: Data were prospectively collected over 5 years (August 2010–August 2015) at our regional trauma and spine unit, regardless of whether the rider was performing the sport competitively or recreationally. Results: During the study period, spine-related injuries were identified for 174 patients (age range, 6-75 years) who were directly referred to our department following recreational or competitive motocross, with most injuries being sustained within the early spring and summer months, representing the start of the motocross season. A significant number of injuries were in males (n = 203, 94%), with the majority of injuries occurring within the 21- to 30-year-old age group. A total of 116 (54%) injuries required operative treatment. The most common spinal injury was thoracolumbar burst fracture (n = 95), followed by chance fractures (n = 26). Conclusion: This data series emphasizes the prevalence and devastation of motocross-related spinal injuries in the United Kingdom and may serve in administering sanctions and guidelines to governing bodies of motocross. The spinal injuries that occur during motocross have significant capital connotations for regional spinal centers. The recent surge in motocross popularity is correlated with the number of injuries, which have increased over the past 5 years by almost 500%. PMID:29349095

  12. [Primary care in the United Kingdom].

    Science.gov (United States)

    Sánchez-Sagrado, T

    2016-03-01

    The inadequate planning of health professionals in Spain has boosted the way out of doctors overseas. The United Kingdom is one of the countries chosen by Spanish doctors to develop their job. The National Health Service is a health system similar to the Spanish one. Health care services are financing mainly through taxes. The right to health care is linked to the citizen condition. The provision of health care is a mix-up of public and private enterprises. Primary Care is much closed to Spanish Primary Care. Doctors are "self-employed like" professionals. They can set their surgeries in a free area previously designed by the government. They have the right to make their own team and to manage their own budget. Medical salary is linked to professional capability and curriculum vitae. The main role of a General Practitioner is the prevention. Team work and coordination within primary and specialised care is more developed than in Spain. The access to diagnostic tests and to the specialist is controlled through waiting lists. General Practitioners work as gate-keepers. Patients may choose freely their doctor and consultations and hospital care are free at the point of use. Within the United Kingdom there are also health regions with problems due to inequalities to access and to treatment. There is a training path and the access to it is by Curricula. The number of training jobs is regulated by the local needs. Continuing education is compulsory and strictly regulated local and nationally. The National Health Service was the example for the Spanish health reform in 1986. While Spanish Primary health care is of quality, the efficiency of the health system would improve if staff in Primary Care settings were managed in a similar way to the British's. Copyright © 2015 Sociedad Española de Médicos de Atención Primaria (SEMERGEN). Publicado por Elsevier España, S.L.U. All rights reserved.

  13. Digital Dissertations in the United Kingdom

    Directory of Open Access Journals (Sweden)

    Ann Matheson

    2000-05-01

    Full Text Available In the United Kingdom a user wishing to consult a UK thesis has traditionally had the following choices: the thesis may be consulted in the Library of the Higher Education Institution (HEI to which it was submitted; the thesis may be borrowed from the library of the HEI; a copy of the thesis may be purchased form the library of the HEI; the thesis may be borrowed through inter-library loan; or the thesis may be made available through the British Library’s British Thesis Service, which was set up in 1971. This Service currently holds more than 150,000 UK theses, which are added to at a rate of around 7,000 a year, with the participation of about a hundred Higher Education Institutions (HEIs. With the development of new technology, however, an interest developed in examining the feasibility of making theses available online to users. In the United Kingdom, the University Theses Online Group (UTOG was established as a consequence of a proposal to the Follett Implementation Group on Information Technology in 1994. The University Theses Online Group (UTOG is a working group of UK university librarians: the Group’s aims are to investigate the technical, cultural and administrative issues associated with the storage and delivery of theses in online form. The Group is made up of representatives of the British Library Document Supply Centre (BLDSC, British Thesis Service, and the university libraries of Cranfield, Edinburgh, Glasgow, Leeds, Manchester, Plymouth, Robert Gordon, University College London, Kent, University of London and Warwick.

  14. Methods of forging steel

    OpenAIRE

    Pečoler, Primož

    2014-01-01

    The following work presents processes of steel forming, challenges when forging steel, forming machines suitable for forging and which choice of machine is most suitable for forging. We can separate steel forming to free forging and drop forging. Free forging can be divided to hand forging and machine forging. The correct choice of furnaces is also very important. We must reach correct temperature in the furnace for raw steel to melt with less scalings. In diploma I mentioned some machine...

  15. Prospects of structural steels

    International Nuclear Information System (INIS)

    Bannykh, O.A.

    2012-01-01

    The current state of world steel production is considered as well as the development strategy of metallurgy industry in the Russian Federation through to 2020. The main factors determining the conservation of steel as perspective material for industry are given: energy expenses on production, the well-proven recirculation technology, the capability of changing steel properties in wide range, temperature range of operation. The conclusion is made that in the immediate future steel will not lose its importance [ru

  16. Trends in steel technology

    International Nuclear Information System (INIS)

    Anon.

    1980-01-01

    Dual phase steels, composite products, and microalloyed steels are making inroads in the automotive industry applications for bumpers, automotive parts, bodies, mechanical parts, suspension and steering equipment and truck bumpers. New steels are also used to support solar mirrors and cells, in corrosive environments in the oil and gas industry, fusion reactors, and pressure vessels in nuclear power plants

  17. Weldability of Stainless Steels

    International Nuclear Information System (INIS)

    Saida, Kazuyoshi

    2010-01-01

    It gives an outline of metallographic properties of welding zone of stainless steels, generation and mechanisms of welding crack and decreasing of corrosion resistance of welding zone. It consists of seven chapters such as introduction, some kinds of stainless steels and properties, metallographic properties of welding zone, weld crack, toughness of welding zone, corrosion resistance and summary. The solidification modes of stainless steels, each solidification mode on the cross section of Fe-Cr-Ni alloy phase diagram, each solidification mode of weld stainless steels metal by electron beam welding, segregation state of alloy elements at each solidification mode, Schaeffler diagram, Delong diagram, effects of (P + S) mass content in % and Cr/Ni equivalent on solidification cracking of weld stainless steels metal, solidification crack susceptibility of weld high purity stainless steels metal, effects of trace impurity elements on solidification crack susceptibility of weld high purity stainless steels metal, ductile fracture susceptibility of weld austenitic stainless steels metal, effects of H2 and ferrite content on generation of crack of weld 25Cr-5N duplex stainless steels, effects of O and N content on toughness of weld SUS 447J1 metals, effect of ferrite content on aging toughness of weld austenitic stainless steel metal, corrosion morphology of welding zone of stainless steels, generation mechanism of knife line attack phenomenon, and corrosion potential of some kinds of metals in seawater at room temperature are illustrated. (S.Y.)

  18. The steel scrap age.

    Science.gov (United States)

    Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

    2013-04-02

    Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age.

  19. A study on EUV reticle surface molecular contamination under different storage conditions in a HVM foundry fab

    Science.gov (United States)

    Singh, SherJang; Yatzor, Brett; Taylor, Ron; Wood, Obert; Mangat, Pawitter

    2017-03-01

    The prospect of EUVL (Extreme Ultraviolet Lithography) insertion into HVM (High Volume Manufacturing) has never been this promising. As technology is prepared for "lab to fab" transition, it becomes important to comprehend challenges associated with integrating EUVL infrastructure within existing high volume chip fabrication processes in a foundry fab. The existing 193nm optical lithography process flow for reticle handling and storage in a fab atmosphere is well established and in-fab reticle contamination concerns are mitigated with the reticle pellicle. However EUVL reticle pellicle is still under development and if available, may only provide protection against particles but not molecular contamination. HVM fab atmosphere is known to be contaminated with trace amounts of AMC's (Atmospheric Molecular Contamination). If such contaminants are organic in nature and get absorbed on the reticle surface, EUV photon cause photo-dissociation resulting into carbon generation which is known to reduce multilayer reflectivity and also degrades exposure uniformity. Chemical diffusion and aggregation of other ions is also reported under the e-beam exposure of a EUV reticle which is known to cause haze issues in optical lithography. Therefore it becomes paramount to mitigate absorbed molecular contaminant concerns on EUVL reticle surface. In this paper, we have studied types of molecular contaminants that are absorbed on an EUVL reticle surface under HVM fab storage and handling conditions. Effect of storage conditions (gas purged vs atmospheric) in different storage pods (Dual pods, Reticle Clamshells) is evaluated. Absorption analysis is done both on ruthenium capping layer as well as TaBN absorber. Ru surface chemistry change as a result of storage is also studied. The efficacy of different reticle cleaning processes to remove absorbed contaminant is evaluated as well.

  20. Use of wasted foundry sand (WFS) as a partial substitute for silica in a soda lime glass; Utilizacao de areia descartada de fundicao (ADF) como substituinte parcial da silica em um vidro soda-cal

    Energy Technology Data Exchange (ETDEWEB)

    Martin, A.C.; Ueno, O.K.; Folgueras, M.V., E-mail: amandacarolinemartin@gmail.com [Universidade do Estado de Santa Catarina (CCT/UDESC), Joinville, SC (Brazil). Centro de Ciencias Tecnologicas

    2016-07-01

    The waste foundry sand (WFS) is the main waste generates in foundry industries. Studies in the literature suggest the use of WFS in different materials, such as concrete, brick or asphalt. This work aims to partially replace the silica of a soda-lime glass by the WFS. The waste foundry sand has in its composition elements such as iron and aluminum that can affect the glass quality, which justifies the residue processing to reduce the impurity content. The treatments, that included mechanical agitation and thermal treatment, resulted in a slight decrease in the percent of iron with consequent increase of the silica content. After treatment, some sands were incorporated into the glass, that showed green color but with lower absorption intensity for the sand with less iron content. It was observed that it's possible to obtain glasses using WFS, however, there is difficulty in color controlling. (author.

  1. Review of production status of heavy steel castings and key technologies for their manufacture in China

    Directory of Open Access Journals (Sweden)

    Liu Baicheng

    2008-02-01

    Full Text Available This paper expatiates on domestic status of heavy steel casting production, with a special focus on hydraulic turbine castings for Three Gorges Project. In China, there is magnificent demand for heavy castings with the rapid growth of the national economy in recent years and the expected high growth in the coming 10 to 20 years. Some heavy and large castings such as mill housing and hydraulic turbine runner crown, blade and band for Three Gorges Project have been successfully made. However, the domestic production capability is still far from meeting the gigantic requirements. The domestic capability still lags behind the world class level, and a lot of heavy castings still depend on import. The paper also gives a particular introduction of the key technologies in the manufacturing of heavy steel castings like metal melting, foundry technology, heat treatment technology and numerical simulation technique, etc. In addition, several case studies on the application of numerical simulation in the production of heavy steel castings are presented.

  2. The United Kingdom's radiotherapy dosimetry audit network

    International Nuclear Information System (INIS)

    Thwaites, D.I.; Allahverdi, M.; Powley, S.K.; Nisbet, A.

    2003-01-01

    The first comprehensive national dosimetry intercomparison in the United Kingdom involving all UK radiotherapy centres was carried out in the late 1980s. Out of this a regular radiotherapy dosimetry audit network evolved in the early 1990s. The network is co-ordinated by the Institute of Physics and Engineering in Medicine and comprises eight co-operative regional groups. Audits are based on site visits using ionization chambers and epoxy resin water substitute phantoms. The basic audit methodology and phantom design follows that of the original national intercomparison exercise. However, most of the groups have evolved more complex methods, to extend the audit scope to include other parameters, other parts of the radiotherapy process and other treatment modalities. A number of the groups have developed phantoms to simulate various clinical treatment situations, enabling the sharing of phantoms and expertise between groups, but retaining a common base. Besides megavoltage external beam photon dosimetry, a number of the groups have also included the audit of kilovoltage X ray beams, electron beams and brachytherapy dosimetry. The National Physical Laboratory is involved in the network and carries out basic beam calibration audits to link the groups. The network is described and the methods and results are illustrated using the Scottish+ group as an example. (author)

  3. International Education in the United Kingdom

    Directory of Open Access Journals (Sweden)

    Denis Hyams-Ssekasi

    2014-12-01

    Full Text Available For the last 40 years, the number of international students aspiring to obtain a qualification in U.K. universities has been exponentially growing. However, such growth has been contested. What seemed to be a “golden” opportunity for Black-African students to pursue their education in the United Kingdom is met with challenges that impact the whole process of adjustment. This article examines these challenges using a qualitative empirical study of Black-African postgraduate students, carried out in three U.K. universities. The methods utilized were observations, focus groups, one-to-one interviews, and a case study to help identify and analyze the issues. The participants reported significant financial pressures and difficulties in understanding and integrating into the culture of U.K. universities. In some cases, these challenges left the students feeling disillusioned and cynical about the value of an international education. Universities must endeavor to tailor their recruitment, orientation, and support programs to the needs of Black-African international students or face damaging their reputations as world-class education providers.

  4. The 1987 United Kingdom radioactive waste inventory

    International Nuclear Information System (INIS)

    1988-10-01

    This report describes the stocks of radioactive wastes in the United Kingdom, together with projections of future arisings. Operational and decommissioning wastes are considered for both committed and prospective plant. Arisings are from power reactors, commercial reprocessing, fuel manufacture, medical and industrial sources and research and development. Data are presented for the wastes in their raw form and as conditioned for disposal. The data which refer to the situation on 1.1.87 are shown by producer and globally, in summary tables. The information presented for each producer includes a description of the activities that generate the wastes and a discussion of how stocks and arisings may have changed from earlier predictions. This is supplemented by a stream by stream tabulation showing the waste type, volume, density, conditioning factor and gross alpha and beta activity. The global projections are presented in tabular and graphical manner, and the changes from earlier projections are discussed. The scenarios which underly the projections are also presented. (author)

  5. A national range inventory for the Kingdom of Lesotho. | Martin ...

    African Journals Online (AJOL)

    A national range inventory for the Kingdom of Lesotho. ... the up-to-date techniques of satellite remote sensing and the interpretation of new colour aerial photography. Data were collected to provided a basic understanding of plant community ...

  6. The United Kingdom's First Woman Law Professor: An Archerian Analysis

    OpenAIRE

    Cownie, FC

    2015-01-01

    In 1970, at Queen's University Belfast, Claire Palley became the first woman to hold a Chair in Law at a United Kingdom university. However, little is known about the circumstances surrounding this event, or Claire Palley herself. This article (part of an extended project exploring her life history) seeks to address the question ‘Was there something about Claire Palley herself that made it more likely she would become the United Kingdom's first female law professor?’ Initially focusing on met...

  7. LMFBR steam generators in the United Kingdom

    International Nuclear Information System (INIS)

    Anderson, R.; Hayden, O.

    2002-01-01

    Experience has been gained in the UK on the operation of LMFBR Steam Generator Units (SGU) over a period of 20 years from the Dounreay Fast Reactor (DFR) and the Prototype Fast Reactor (PFR). The DFR steam generator featured a double barrier and therefore did not represent a commercial design. PFR, however, faced the challenge of a single wall design and it is experience from this which is most valuable. The PFR reactor went critical in March 1974 and the plant operating history since then has been dominated by experience with leaks in the tube to tube plate welds of the high performance U-tubes SGU's. Operation at high power using the full complement of three secondary sodium circuits was delayed until July 1976 by the occurrence of leaks in the tube to tube plate welds of the superheater and reheater units which are fabricated in stainless steel. Repairs were carried out to the two superheaters and they were returned to service. The reheater tube bundle was removed from circuit after sodium was found to have entered the steam side. When the sodium had been removed and inspection carried out it was decided not to recover the unit. Since 1976 the remaining five stainless steel units have operated satisfactorily. This year a replacement reheater unit has been installed. This is of a new design in 9-Cr-Mo ferritic steel using a sleeve through which the steam tube passes to eliminate the tube to tube plate weld. Despite a few early leaks in evaporator tube to tube plate welds up to 1979, these failures did not initially present a major problem. However, in 1980 the rate of evaporator weld failures increased and despite the successful application of a shot peening process to eliminate stress corrosion failures from the water side of the weld, failures traced to the sodium side continued. A sleeving process was developed for application to complete evaporator units on a production basis with the objective of bypassing the welds at each end of the 500 tubes. The decision

  8. Heavy steel casting components for power plants 'mega-components' made of high Cr-steels

    Energy Technology Data Exchange (ETDEWEB)

    Hanus, Reinhold [voestalpine Giesserei Linz GmbH, Linz (Austria)

    2010-07-01

    Steel castings of creep resistant steels play a key role in fossil fuel fired power plants for highly loaded components in the high and intermediate pressure section of the turbines. Inner and outer casings, valve casings, inlet connections and elbows are examples of such critical components. The most important characteristic in a power plant is the efficiency, which mainly drives the CO2-emission. As a consequence of steadily improving power plant efficiencies and ever stricter emission standards, steam parameters become more critical and the creep resistance of the cast materials must also be constantly improved. The foundries voestalpine Giesserei Linz and voestalpine Giesserei Traisen participated in the development of the new 9-10% Cr-steels for application up to 625 C/650 C and in the THERMIE project where Ni-base alloys for 700 C-power plants were developed. Beside the material development in the European research projects the commercial production had to be established for industrial processes and the newly developed materials have to be transferred from research into the commercial production of heavy cast components. After selecting the most promising alloy from the laboratory melts, welding tests were performed - mostly with matching electrodes also produced within COST/THERMIE. Base material and welds were investigated in respect of microstructure, creep resistance, mechanical properties and weldability. Heat treatment investigations were also necessary for optimization of the mechanical properties. Based on the results of these studies, pilot components and plates for testing welding processes were cast in order to verify the castability and weldability of larger parts and to make any necessary adjustments to chemical composition, heat treatment or welding parameters. Parallel to the ongoing creep tests within COST/THERMIE-program, the newly developed steel grades were introduced into the commercial production of large components. This involved finding

  9. The Kingdom of God within us, according to Meister Eckhart

    Directory of Open Access Journals (Sweden)

    Silvia Bara Bancel

    2017-05-01

    Full Text Available In this paper, we examine what the German works of Meister Eckhart (c. 1260-1328 say about heaven, the Kingdom of God and the Kingdom of Heaven. We explain how he understands the presence of the Kingdom of God in us. In a style that is fresh and original, Eckhart says that the Kingdom of Heaven is now already within us. It is in the deepest part of us, in the ground of the soul, but man does not discover it immediately. In the first place, he has to prepare himself and to be receptive to the Kingdom of God, to God within himself. He has to make himself «heavenly», through humility, detachment, equanimity and so on. Furthermore, God «flows» inside this person and He pronounce His Word in him. That is how the human being becomes the son of God, how he receives a «kiss» from God, and how the Kingdom of God breaks through in the ground of the soul. And that finally means participating now in the joy and the blessedness of heaven.

  10. Summary of the IEA workshop/working group meeting on ferritic/martensitic steels for fusion

    Energy Technology Data Exchange (ETDEWEB)

    Klueh, R.L. [Oak Ridge National Lab., TN (United States)

    1997-04-01

    An International Energy Agency (IEA) Working Group on Ferritic/Martensitic Steels for Fusion Applications, consisting of researchers from Japan, the European Union, the United States, and Switzerland, met at the headquarters of the Joint European Torus (JET), Culham, United Kingdom, 24-25 October 1996. At the meeting preliminary data generated on the large heats of steel purchased for the IEA program and on other heats of steels were presented and discussed. The second purpose of the meeting was to continue planning and coordinating the collaborative test program in progress on reduced-activation ferritic/martensitic steels. The next meeting will be held in conjunction with the International Conference on Fusion Reactor Materials (ICFRM-8) in Sendai, Japan, 23-31 October 1997.

  11. Summary of the IEA workshop/working group meeting on ferritic/martensitic steels for fusion

    International Nuclear Information System (INIS)

    Klueh, R.L.

    1997-01-01

    An International Energy Agency (IEA) Working Group on Ferritic/Martensitic Steels for Fusion Applications, consisting of researchers from Japan, the European Union, the United States, and Switzerland, met at the headquarters of the Joint European Torus (JET), Culham, United Kingdom, 24-25 October 1996. At the meeting preliminary data generated on the large heats of steel purchased for the IEA program and on other heats of steels were presented and discussed. The second purpose of the meeting was to continue planning and coordinating the collaborative test program in progress on reduced-activation ferritic/martensitic steels. The next meeting will be held in conjunction with the International Conference on Fusion Reactor Materials (ICFRM-8) in Sendai, Japan, 23-31 October 1997

  12. Country policy profile - United Kingdom. August 2015

    International Nuclear Information System (INIS)

    2015-08-01

    United Kingdom is legally committed to meeting 15% of the UK's energy demand from renewable sources by 2020. The country considers renewables will also have a crucial role to play in the UK energy mix in the decades beyond, making the most of the UK's abundant natural resources. To increase and accelerate the use of renewable energy, the UK has introduced a number of legislative tools. A Renewables Obligation (RO) who provides incentives for large-scale renewable electricity generation by making UK suppliers source a proportion of their electricity from eligible renewable sources A Feed-in Tariffs (FITs) scheme -who pays energy users who invest in small-scale, low-carbon electricity generation systems for the electricity they generate and use, and for unused electricity they export back to the grid A Renewable Heat Incentive (RHI) who pays commercial, industrial, public, not-for-profit and community generators of renewable heat for a 20-year period A Renewable Heat Premium Payment (RHPP) who gives one-off payments to householders, communities and social housing landlords to help them buy renewable heating technologies like solar thermal panels, heat pumps and biomass boilers A Renewable Transport Fuel Obligation who makes companies that supply more than 450,000 litres of fuel per year source a percentage from renewable sources. Besides its instruments, the British government is working to the implementation of the Electricity Market Reform (EMR) will also provide support for the production of renewable electricity from 2014 onwards. EMR introduces two key mechanisms to provide incentives for the investment required in our energy infrastructure. The Contracts for Difference (CFD) who provides long-term price stabilisation to low carbon plant, allowing investment to come forward at a lower cost of capital and therefore at a lower cost to consumers and the Capacity Market who provides a regular retainer payment to reliable forms of capacity (both demand and supply

  13. Country policy profile - United Kingdom. December 2015

    International Nuclear Information System (INIS)

    2015-12-01

    United Kingdom is legally committed to meeting 15% of the UK's energy demand from renewable sources by 2020. The country considers renewables will also have a crucial role to play in the UK energy mix in the decades beyond, making the most of the UK's abundant natural resources. To increase and accelerate the use of renewable energy, the UK has introduced a number of legislative tools. A Renewables Obligation (RO) who provides incentives for large-scale renewable electricity generation by making UK suppliers source a proportion of their electricity from eligible renewable sources A Feed-in Tariffs (FITs) scheme -who pays energy users who invest in small-scale, low-carbon electricity generation systems for the electricity they generate and use, and for unused electricity they export back to the grid A Renewable Heat Incentive (RHI) who pays commercial, industrial, public, not-for-profit and community generators of renewable heat for a 20-year period A Renewable Heat Premium Payment (RHPP) who gives one-off payments to householders, communities and social housing landlords to help them buy renewable heating technologies like solar thermal panels, heat pumps and biomass boilers A Renewable Transport Fuel Obligation who makes companies that supply more than 450,000 litres of fuel per year source a percentage from renewable sources. Besides its instruments, the British government is working to the implementation of the Electricity Market Reform (EMR) will also provide support for the production of renewable electricity from 2014 onwards. EMR introduces two key mechanisms to provide incentives for the investment required in our energy infrastructure. The Contracts for Difference (CFD) who provides long-term price stabilisation to low carbon plant, allowing investment to come forward at a lower cost of capital and therefore at a lower cost to consumers and the Capacity Market who provides a regular retainer payment to reliable forms of capacity (both demand and supply

  14. Country policy profile - United Kingdom. October 2014

    International Nuclear Information System (INIS)

    2014-10-01

    United Kingdom is legally committed to meeting 15% of the UK's energy demand from renewable sources by 2020. The country considers renewables will also have a crucial role to play in the UK energy mix in the decades beyond, making the most of the UK's abundant natural resources. To increase and accelerate the use of renewable energy, the UK has introduced a number of legislative tools. A Renewables Obligation (RO) which provides incentives for large-scale renewable electricity generation by making UK suppliers source a proportion of their electricity from eligible renewable sources. A Feed-in Tariffs (FITs) scheme -which pays energy users who invest in small-scale, low-carbon electricity generation systems for the electricity they generate and use, and for unused electricity they export back to the grid. A Renewable Heat Incentive (RHI) which pays commercial, industrial, public, not-for-profit and community generators of renewable heat for a 20-year period. A Renewable Heat Premium Payment (RHPP) which gives one-off payments to householders, communities and social housing landlords to help them buy renewable heating technologies like solar thermal panels, heat pumps and biomass boilers. A Renewable Transport Fuel Obligation which makes companies that supply more than 450,000 litres of fuel per year source a percentage from renewable sources. Besides its instruments, the British government is working to the implementation of the Electricity Market Reform (EMR), which will also provide support for the production of renewable electricity from 2014 onwards. EMR introduces two key mechanisms to provide incentives for the investment required in our energy infrastructure. The Contracts for Difference (CFD), which provide long-term price stabilisation to low carbon plants, allowing investment to come forward at a lower cost of capital and therefore at a lower cost to consumers and the Capacity Market, which provides a regular retainer payment to reliable forms of capacity

  15. Child Poverty: The United Kingdom Experience.

    Science.gov (United States)

    Mansour, Jane G; Curran, Megan A

    2016-04-01

    The United States has long struggled with high levels of child poverty. In 2014, 2 of 5 (42.9%) of all American children lived in economically insecure households and just over 1 in 5 children lived below the official absolute poverty line. These rates are high, but not intractable. Evidence from the US Census Bureau's Supplemental Poverty Measure, among other sources, shows the effect that public investments in cash and noncash transfers can have in reducing child poverty and improving child well-being. However, with significant disparities in services and supports for children across states and the projected decline of current federal spending on children, the United States is an international outlier in terms of public investments in children, particularly compared with other high-income nations. One such country, the United Kingdom (UK), faced similar child poverty challenges in recent decades. At the end of the 20th century, the British Prime Minister pledged to halve child poverty in a decade and eradicate it 'within a generation.' The Labour Government then set targets and dedicated resources in the form of income supplements, employment, child care, and education support. Child poverty levels nearly halved against an absolute measure by the end of the first decade. Subsequent changes in government and the economy slowed progress and have resulted in a very different approach. However, the UK child poverty target experience, 15 years in and spanning multiple changes in government, still offers a useful comparative example for US social policy moving forward. Copyright © 2016 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

  16. Steel: Price and Policy Issues

    National Research Council Canada - National Science Library

    Cooney, Stephen

    2006-01-01

    Steel prices remain at historically elevated levels. The rapid growth of steel production and demand in China is widely considered as a major cause of the increases in both steel prices and the prices of steelmaking inputs...

  17. Elastic-plastic fracture analysis of carbon steel piping using the latest CEGB R6 approach

    International Nuclear Information System (INIS)

    Kanno, S.; Hasegawa, K.; Shimizu, T.; Kobayashi, H.

    1991-01-01

    The elastic-plastic fracture of carbon steel piping having various pipe diameters and circumferential crack angles and subjected to a bending moment is analyzed using the latest United Kingdom Central Electricity Generating Board R6 approach. The elastic-plastic fracture criterion must be applied instead of the plastic collapse criterion with increase of the pipe diameter and the crack angle. A simplified elastic-plastic fracture analysis procedure based on the R6 approach is proposed. (author)

  18. Characterising Record Flooding in the United Kingdom

    Science.gov (United States)

    Cox, A.; Bates, P. D.; Smith, J. A.

    2017-12-01

    Though the most notable floods in history have been carefully explained, there remains a lack of literature that explores the nature of record floods as a whole in the United Kingdom. We characterise the seasonality, statistical and spatial distribution, and meteorological causes of peak river flows for 521 gauging stations spread across the British Isles. We use annual maximum data from the National River Flow Archive, catchment descriptors from the Flood Estimation Handbook, and historical records of large floods. What we aim to find is in what ways, if any, the record flood for a station is different from more 'typical' floods. For each station, we calculate two indices: the seasonal anomaly and the flood index. Broadly, the seasonal anomaly is the degree to which a station's record flood happens at a different time of year compared to typical floods at that site, whilst the flood index is a station's record flood discharge divided by the discharge of the 1-in-10-year return period event. We find that while annual maximum peaks are dominated by winter frontal rainfall, record floods are disproportionately caused by summer convective rainfall. This analysis also shows that the larger the seasonal anomaly, the higher the flood index. Additionally, stations across the country have record floods that occur in the summer with no notable spatial pattern, yet the most seasonally anomalous record events are concentrated around the south and west of the British Isles. Catchment descriptors tell us little about the flood index at a particular station, but generally areas with lower mean annual precipitation have a higher flood index. The inclusion of case studies from recent and historical examples of notable floods across the UK supplements our analysis and gives insight into how typical these events are, both statistically and meteorologically. Ultimately, record floods in general happen at relatively unexpected times and with unpredictable magnitudes, which is a

  19. The reactor vessel steels

    International Nuclear Information System (INIS)

    Bilous, W.; Hajewska, E.; Szteke, W.; Przyborska, M.; Wasiak, J.; Wieczorkowski, M.

    2005-01-01

    In the paper the fundamental steels using in the construction of pressure vessel water reactor are discussed. The properties of these steels as well as the influence of neutron irradiation on its degradation in the time of exploitation are also done. (authors)

  20. Steel Industry Wastes.

    Science.gov (United States)

    Schmidtke, N. W.; Averill, D. W.

    1978-01-01

    Presents a literature review of wastes from steel industry, covering publications of 1976-77. This review covers: (1) coke production; (2) iron and steel production; (3) rolling operations; and (4) surface treatment. A list of 133 references is also presented. (NM)

  1. The future of nuclear power in the United Kingdom

    International Nuclear Information System (INIS)

    Jones, P.M.S.

    1990-01-01

    The arguments that have been put forward in the United Kingdom to justify the contention by its opponents that nuclear power should not be seen as a safe, economic, strategically desirable and environmentally attractive energy source are examined. Counter arguments are presented to support the belief that these are wholly wrong. In the short to medium term, however, economic and political considerations suggest that the prospects for nuclear power in the United Kingdom are not optimistic. The long term evolution of nuclear power is uncertain but it is possible that the security of energy supply, comparative economics and environmental attractions associated with nuclear power will become more apparent and work in its favour eventually. The conviction is expressed that, by the middle of the next century, the United Kingdom will be reaping the benefits of the fast reactor on a significant scale. (UK)

  2. Hazardous healthcare waste management in the Kingdom of Bahrain

    International Nuclear Information System (INIS)

    Mohamed, L.F.; Ebrahim, S.A.; Al-Thukair, A.A.

    2009-01-01

    Hazardous healthcare waste has become an environmental concern for many developing countries including the Kingdom of Bahrain. There have been several significant obstacles facing the Kingdom in dealing with this issue including; limited documentation regarding generation, handling, management, and disposal of waste. This in turn hinders efforts to plan better healthcare waste management. In this paper, hazardous waste management status in the Kingdom has been investigated through an extensive survey carried out on selected public and private healthcare premises. Hazardous waste management practices including: waste generation, segregation, storage, collection, transportation, treatment, and disposal were determined. The results of this study along with key findings are discussed and summarized. In addition; several effective recommendations and improvements of hazardous waste management are suggested.

  3. United Kingdom (England): Health system review.

    Science.gov (United States)

    Boyle, Seán

    2011-01-01

    The Health Systems in Transition (HiT) profiles are country-based reports that provide a detailed description of a health system and of policy initiatives in progress or under development. HiTs examine different approaches to the organization, financing and delivery of health services and the role of the main actors in health systems; describe the institutional framework, process, content and implementation of health and health care policies; and highlight challenges and areas that require more in-depth analysis. Various indicators show that the health of the population has improved over the last few decades. However, inequalities in health across socioeconomic groups have been increasing since the 1970s. The main diseases affecting the population are circulatory diseases, cancer, diseases of the respiratory system and diseases of the digestive system. Risk factors such as the steadily rising levels of alcohol consumption, the sharp increases in adult and child obesity and prevailing smoking levels are among the most pressing public health concerns, particularly as they reflect the growing health inequalities among different socioeconomic groups. Health services in England are largely free at the point of use. The NHS provides preventive medicine, primary care and hospital services to all those ordinarily resident. Over 12% of the population is covered by voluntary health insurance schemes, known in the United Kingdom as private medical insurance (PMI), which mainly provides access to acute elective care in the private sector. Responsibility for publicly funded health care rests with the Secretary of State for Health, supported by the Department of Health. The Department operates at a regional level through 10 strategic health authorities (SHAs), which are responsible for ensuring the quality and performance of local health services within their geographic area. Responsibility for commissioning health services at the local level lies with 151 primary care

  4. Assessment of tensile and creep data for types 304 and 316 stainless steel

    International Nuclear Information System (INIS)

    Sikka, V.K.; Booker, M.K.

    1976-01-01

    Austenitic stainless steels of types 304 and 316 are prime construction materials for nuclear fast breeder reactors and will be used in the temperature range where elevated-temperature, tensile, creep, and fatigue properties are required to calculate the design stress limits. This report examines the possible variations in such properties, using data from several sources including data from Japan and the United Kingdom. United States data were shown to contain the largest variations in both tensile and creep properties, with Japanese data the least. For a given country no distinction could be made in variations in tensile properties of types 304 and 316 stainless steels, but variations in standard error of estimate for all creep properties analyzed were significantly lower for type 316 stainless steel than corresponding variations in creep properties of type 304 stainless steel. The data from each of these countries showed the same creep rupture strength (at 10 4 h) for type 316 stainless steel; this was not true for the type 304 stainless steel. Results of the analysis performed in this paper showed that the U.S. and foreign data on types 304 and 316 stainless steels could possibly be combined for the determination of design stress intensity limits

  5. Damascus steel ledeburite class

    Science.gov (United States)

    Sukhanov, D. A.; Arkhangelsky, L. B.; Plotnikova, N. V.

    2017-02-01

    Discovered that some of blades Damascus steel has an unusual nature of origin of the excess cementite, which different from the redundant phases of secondary cementite, cementite of ledeburite and primary cementite in iron-carbon alloys. It is revealed that the morphological features of separate particles of cementite in Damascus steels lies in the abnormal size of excess carbides having the shape of irregular prisms. Considered three hypotheses for the formation of excess cementite in the form of faceted prismatic of excess carbides. The first hypothesis is based on thermal fission of cementite of a few isolated grains. The second hypothesis is based on the process of fragmentation cementite during deformation to the separate the pieces. The third hypothesis is based on the transformation of metastable cementite in the stable of angular eutectic carbide. It is shown that the angular carbides are formed within the original metastable colony ledeburite, so they are called “eutectic carbide”. It is established that high-purity white cast iron is converted into of Damascus steel during isothermal soaking at the annealing. It was revealed that some of blades Damascus steel ledeburite class do not contain in its microstructure of crushed ledeburite. It is shown that the pattern of carbide heterogeneity of Damascus steel consists entirely of angular eutectic carbides. Believe that Damascus steel refers to non-heat-resistant steel of ledeburite class, which have similar structural characteristics with semi-heat-resistant die steel or heat-resistant high speed steel, differing from them only in the nature of excess carbide phase.

  6. Environmental impact of some trace elements emission from the work environment of Atbara Cement Factory and Atbara Railway Foundry

    Energy Technology Data Exchange (ETDEWEB)

    Nimir, S A.M. [University of Khartoum, Faculty of Education, Department of Chemistry, Khartoum (Sudan)

    2006-06-15

    This work was performed to evaluate the chemical pollution level by some trace elements at the work environment of Atbara Cement Factory (ACF) and Atbara Railway Foundry (ARF). Samples of soil and air were collected from the two sites study, ACF and ARF. To assess the environmental impact of these industrial complexes, the samples were collected from sites expected to be free from industrial emission to serve as control. Plant samples were also collected from (ACF) and the control site. The samples were analyzed and the concentrations of K, Na, Mn, Fe, Cu, Zu and Pb were determined using three analytical techniques: Atomic absorption spectroscopy (AAS), X-ray fluorescence (X RF), and flame emission photometry (FEP). Soil samples were chemically fractionated using separation methods and the solutions were analyzed using AAS methods and FEP to determine the chemical form of the elements. The quality of the data was achieved through the analysis of certified reference materials. The results of this study were compared with previous literature. The data were treated by calculating enrichment factor and statistically by multivariate analysis such as, principle component analysis and cluster analysis. The findings of the study were concluded as follows. The effect of emission from both sites is very clear when the concentrations of the studied trace elements in soil and air samples are compared with the respective concentrations at the control site. Higher values of these elements are found at ARF and slightly high at ACF. The elements which can be attributed to industrial emission are noticeably higher at ARF, for example Cu is forty times as higher as compared to the control site. While Zn is slightly high and Pb is very high. The same remarks are further confirmed by enrichment factor calculation. For soil samples enrichment factor was obtained for two groups of elements, the enriched group includes the elements Pb, Cu and Zn which have enrichment factors higher in

  7. Environmental impact of some trace elements emission from the work environment of Atbara Cement Factory and Atbara Railway Foundry

    International Nuclear Information System (INIS)

    Nimir, S.A.M.

    2006-06-01

    This work was performed to evaluate the chemical pollution level by some trace elements at the work environment of Atbara Cement Factory (ACF) and Atbara Railway Foundry (ARF). Samples of soil and air were collected from the two sites study, ACF and ARF. To assess the environmental impact of these industrial complexes, the samples were collected from sites expected to be free from industrial emission to serve as control. Plant samples were also collected from (ACF) and the control site. The samples were analyzed and the concentrations of K, Na, Mn, Fe, Cu, Zu and Pb were determined using three analytical techniques: Atomic absorption spectroscopy (AAS), X-ray fluorescence (X RF), and flame emission photometry (FEP). Soil samples were chemically fractionated using separation methods and the solutions were analyzed using AAS methods and FEP to determine the chemical form of the elements. The quality of the data was achieved through the analysis of certified reference materials. The results of this study were compared with previous literature. The data were treated by calculating enrichment factor and statistically by multivariate analysis such as, principle component analysis and cluster analysis. The findings of the study were concluded as follows. The effect of emission from both sites is very clear when the concentrations of the studied trace elements in soil and air samples are compared with the respective concentrations at the control site. Higher values of these elements are found at ARF and slightly high at ACF. The elements which can be attributed to industrial emission are noticeably higher at ARF, for example Cu is forty times as higher as compared to the control site. While Zn is slightly high and Pb is very high. The same remarks are further confirmed by enrichment factor calculation. For soil samples enrichment factor was obtained for two groups of elements, the enriched group includes the elements Pb, Cu and Zn which have enrichment factors higher in

  8. Finite volume modeling of the solidification of an axial steel cast impeller

    Directory of Open Access Journals (Sweden)

    M. Copur

    2014-04-01

    Full Text Available In the foundry industry, obtaining the solidification contours in cast geometries are extremely important to know the last location(s to solidify in order to define the correct feeding path and the number of risers. This paper presents three-dimensional simulation of transient conduction heat transfer within an axial impeller, made of AISI 1016 steel, poured and solidified in chemically bonded mold and core medium, by using FVM technique and ANSYS CFX. Specific heat, density and thermal conductivity of AISI 1016 steel, mold and Core materials are considered as functions of temperatures. In this transient thermal analysis, the convection heat transfer phenomenon is also considered at the outer surfaces of the mold. In order to shorten the run-time, the nonlinear transient analysis has been made for 600/3600 segment of the impeller, core and mold. The solidification contours of the impeller as well as isothermal lines in core and mold have been obtained in 3-D. The cooling curves of diff erent points are also shown in the result section.

  9. Structural amorphous steels

    International Nuclear Information System (INIS)

    Lu, Z.P.; Liu, C.T.; Porter, W.D.; Thompson, J.R.

    2004-01-01

    Recent advancement in bulk metallic glasses, whose properties are usually superior to their crystalline counterparts, has stimulated great interest in fabricating bulk amorphous steels. While a great deal of effort has been devoted to this field, the fabrication of structural amorphous steels with large cross sections has remained an alchemist's dream because of the limited glass-forming ability (GFA) of these materials. Here we report the discovery of structural amorphous steels that can be cast into glasses with large cross-section sizes using conventional drop-casting methods. These new steels showed interesting physical, magnetic, and mechanical properties, along with high thermal stability. The underlying mechanisms for the superior GFA of these materials are discussed

  10. Life after Steel

    Science.gov (United States)

    Mangan, Katherine

    2013-01-01

    Bobby Curran grew up in a working-class neighborhood in Baltimore, finished high school, and followed his grandfather's steel-toed bootprints straight to Sparrows Point, a 3,000-acre sprawl of industry on the Chesapeake Bay. College was not part of the plan. A gritty but well-paying job at the RG Steel plant was Mr. Curran's ticket to a secure…

  11. the metanoetic presence of the kingdom of god in a fluid new world ...

    African Journals Online (AJOL)

    Therefore, the emphasis on order, predictability and open dialogue in religious circles, as ... augmented by a metanoetic understanding of the kingdom of God. ..... in infinite quantities. Just as he .... Leaders on the open seas of the kingdom are ...

  12. Operative training in otolaryngology in the United Kingdom: a specialist registrar survey

    NARCIS (Netherlands)

    Georgalas, Christos; Hadjihannas, Edward; Ghufoor, Khalid; Pracy, Paul; Papesch, Michael

    2005-01-01

    OBJECTIVE: To assess the current status of operative training for otolaryngology specialist registrars in the United Kingdom. DESIGN: Web-based questionnaire survey. PARTICIPANTS: All otolaryngology specialist registrars in the United Kingdom. MAIN OUTCOME MEASURES: The overall satisfaction with

  13. Kingdom, church and civil society: A theological paradigm for civil ...

    African Journals Online (AJOL)

    2015-04-23

    Apr 23, 2015 ... smart phone or mobile ... political discourse and application of new policies did not lead to the delivery of the initial promise of a .... Moltmann (1965:22) did not use this terminology, but .... The relation of kingdom and church is essential to an ..... application of this hypothesis is problematic because modern.

  14. Institutional Churn: Institutional Change in United Kingdom Higher Education

    Science.gov (United States)

    Tight, Malcolm

    2013-01-01

    This article considers how higher education institutions change over time, using the United Kingdom system as an exemplar, and focusing on the 15-year period between 1994/95 and 2009/10. While there are many aspects of institutional change worthy of study, the focus here is on how institutions appear to others. Thus, the article examines the…

  15. Assets, Aliens or Asylum Seekers? Immigration and the United Kingdom

    Science.gov (United States)

    Haste, Helen

    2006-01-01

    British attitudes toward immigrants are complex. The United Kingdom has received regular waves of immigrants, both political and economic asylum seekers and, especially in recent decades, recruited labor from the former nations of the British Empire. Throughout its history, ambivalence among the Britons is seen due to these developments. In this…

  16. The kingdom of God: Utopian or existential? | Malan | HTS ...

    African Journals Online (AJOL)

    Was it meant to be understood as utopian as Mary Ann Beavis views it, or existential? In 1st century CE Palestine, kingdom of God was a political term meaning theocracy suggesting God's patronage. Jesus used the term metaphorically to construct a new symbolic universe to legitimate a radical new way of living with God ...

  17. Summary report on the 1985 United Kingdom radioactive waste inventory

    International Nuclear Information System (INIS)

    Fletcher, A.M.; Wear, F.J.; Haselden, H.; Shepherd, J.; Tymons, B.J.

    1986-04-01

    Stocks of radioactive waste in the United Kingdom which have arisen, or are projected to arise, from commercial nuclear power reactors and fuel cycle facilities, research, medical and industrial uses of radioactive nuclides are given in the form of summary tables. Projected future arisings from operation and decommissioning of facilities and notional nuclear power generation programmes to 2030 are also given. (author)

  18. THE MESSIANIC KINGDOM THEOLOGY IN LUKE-ACTS ...

    African Journals Online (AJOL)

    HP

    Paul W. Walaskay argues that Luke espouses a ―majestic .... thrust concerned with Jesus' messianic kingdom as the Gospel of Luke. Also, in the Gospel, ..... Thompson S.J. Ed. (David E. Aune. ... 72), Editor: John J. Collins, Leiden: Brill,. 2011 ...

  19. Kingdom of Bhutan VIP visit at CERN / CMS

    CERN Document Server

    Hoch, Michael

    2014-01-01

    His Excellency Mr Yeshey Zimba Member of Parliament and His Excellency Daw Penjo Ambassador and Permanent Representative of the Kingdom of Bhutan visiting at CERN the LHC tunnel and the CMS experiment. Further guests were : Mrs Daw Zam, Mrs Thuji Zangmo, Mr. Rinchen Dorji, Mrs Dechen Wangmo, Ms Choni Ome Guided by R. Voss, Michael Hoch, Tiziano Camporesi

  20. An Update on Asset Management Plans in the United Kingdom.

    Science.gov (United States)

    Patel, Mukund

    1999-01-01

    Describes a current project in the United Kingdom designed to improve school buildings. The use of Asset Management Plans (AMPs) in providing the means through which likely future needs are assessed, criteria for prioritization are set, and informed decisions on local spending are made are examined. (GR)

  1. Kingdom, church and civil society: A theological paradigm for civil ...

    African Journals Online (AJOL)

    This article deals with the role that churches can and should play in civil society to develop societal morally. The central-theoretical argument is that the biblical notion of the kingdom of God can, when it is systematically and theologically developed, offer an acceptable foundation for the civil action of churches. In light of this ...

  2. Nuclear information and education experience in the United Kingdom

    International Nuclear Information System (INIS)

    Ginniff, M.E.

    1993-01-01

    The presentation discusses the importance of public information and education in the field of energy and particularly in the field of nuclear energy development. The attempt is made to explain some issues connected with the nuclear fuel cycle. Appendix contains comments on the United Kingdom educational materials in this area

  3. Innovative United Kingdom Approaches To Measuring Service Quality.

    Science.gov (United States)

    Winkworth, Ian

    2001-01-01

    Reports on approaches to measuring the service quality of academic libraries in the United Kingdom. Discusses the role of government and the national background of quality measurement; measurement frameworks; better use of statistics; benchmarking; measuring user satisfaction; and possible future development. (Author/LRW)

  4. Computertomographic investigation of steel fibre reinforced sprayed concrete using multi-dimensional transfer functions [Computertomografische Untersuchung von Stahlfaserspritzbeton mit mehrdimensionalen Transferfunktionen

    KAUST Repository

    Pittino, Gerhard

    2011-06-01

    The composite material steel fibre reinforced concrete or steel fibre reinforced sprayed concrete (SFRS) is widely used in geotechnics. For the modelling of the mechanical behaviour the knowledge of the distribution and orientation of the fibres in the concrete is of particular importance. For a bachelor thesis the steel fibres in drill cores were investigated by computed tomography (CT) at the Austrian Foundry Research Institute (ÖGI). The orientation of each fibre was calculated using a STL-interface and further software tools. The results were statistically evaluated and graphically represented using Schmidt\\'s net. This time consuming (expensive) method was automated by a post-processing of VRVis. With that tool the steel fibres in the sample can be explored, classified and visually examined in real-time regarding their orientation in two angles. Different possibilities of statistical evaluation can be implemented. A real-time direction sphere histogram (DSH), comparable to Schmidt\\'s net in 3D allows the user to recognise the distribution of orientations of the selected fibres at a glance. The colour-coding of the different orientations is also used for the 3D-volume-view of the fibres, to easily identify the spatial distribution of orientations in the SFRS sample. © 2011 Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG, Berlin.

  5. 77 FR 12241 - Smart Grid Trade Mission to the United Kingdom; London, United Kingdom, October 15-17, 2012

    Science.gov (United States)

    2012-02-29

    ... from the World Bank, the United Kingdom is the best place to do business in the EU and G8 countries... smart grid. Consequently, over $300 billion of investment is needed over the next ten years to replace... distributing ever increasing amounts of electricity from intermittent and geographically spread renewable...

  6. Clean steels for fusion

    International Nuclear Information System (INIS)

    Gelles, D.S.

    1995-03-01

    Fusion energy production has an inherent advantage over fission: a fuel supply with reduced long term radioactivity. One of the leading candidate materials for structural applications in a fusion reactor is a tungsten stabilized 9% chromium Martensitic steel. This alloy class is being considered because it offers the opportunity to maintain that advantage in the reactor structure as well as provide good high temperature strength and radiation induced swelling and embrittlement resistance. However, calculations indicate that to obtain acceptable radioactivity levels within 500 years after service, clean steel will be required because the niobium impurity levels must be kept below about 2 appm and nickel, molybdenum, nitrogen, copper, and aluminum must be intentionally restricted. International efforts are addressing the problems of clean steel production. Recently, a 5,000 kg heat was vacuum induction melted in Japan using high purity commercial raw materials giving niobium levels less than 0.7 appm. This paper reviews the need for reduced long term radioactivity, defines the advantageous properties of the tungsten stabilized Martensitic steel class, and describes the international efforts to produce acceptable clean steels

  7. Steel fiber reinforced concrete

    International Nuclear Information System (INIS)

    Baloch, S.U.

    2005-01-01

    Steel-Fiber Reinforced Concrete is constructed by adding short fibers of small cross-sectional size .to the fresh concrete. These fibers reinforce the concrete in all directions, as they are randomly oriented. The improved mechanical properties of concrete include ductility, impact-resistance, compressive, tensile and flexural strength and abrasion-resistance. These uniqlte properties of the fiber- reinforcement can be exploited to great advantage in concrete structural members containing both conventional bar-reinforcement and steel fibers. The improvements in mechanical properties of cementitious materials resulting from steel-fiber reinforcement depend on the type, geometry, volume fraction and material-properties of fibers, the matrix mix proportions and the fiber-matrix interfacial bond characteristics. Effects of steel fibers on the mechanical properties of concrete have been investigated in this paper through a comprehensive testing-programme, by varying the fiber volume fraction and the aspect-ratio (Lid) of fibers. Significant improvements are observed in compressive, tensile, flexural strength and impact-resistance of concrete, accompanied by marked improvement in ductility. optimum fiber-volume fraction and aspect-ratio of steel fibers is identified. Test results are analyzed in details and relevant conclusions drawn. The research is finally concluded with future research needs. (author)

  8. Final Report, Volume 4, The Develpoment of Qualification Standards forCast Super Duplex Stainless Steel (2507 Wrought Equivalent)

    Energy Technology Data Exchange (ETDEWEB)

    Hariharan, Vasudevan; Lundin, Carl, D.

    2005-09-30

    The objective of the program is to determine the suitability of ASTM A923 Standard Test methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic-Ferritic Stainless Steels for 25 Cr Cast Super Duplex Stainless Steels (ASTM A890-5A). Different tests were carried out on the materials procured from various steel foundries as stated in the ASTM A923. The foundries were designated as Foundry A, B, C and D. All the materials were foundry solution annealed. Materials from Foundry D were solution heat treated at The University of Tennessee also and then they were subjected to heat treatment schedule which was derived from the testing of wrought DSS to establish the A923 specification. This was possible because the material from the same heat was sufficient for conducting the full scope of heat treatment. This was done prior to carrying out various other tests. Charpy samples were machined. The Ferrite content was measured in all the Charpy samples using Feritscope{reg_sign} and ASTM E562 Manual Point Count Method. After the ferrite content was measured the samples were sent to AMC-Vulcan, Inc. in Alabama to conduct the Charpy impact test based on ASTM A923 Test Method B. This was followed by etch testing and corrosion analysis based on ASTM A923 Test Methods A and C respectively at University of Tennessee. Hardness testing using Rockwell B and C was also carried out on these samples. A correlation was derived between all the three test methods and the best method for evaluating the presence of intermetallic in the material was determined. The ferrite content was correlated with the toughness values. Microstructural analysis was carried out on the etch test samples using Scanning Electron Microscopy in order to determine if intermetallic phases were present. The fracture surfaces from Charpy test specimens were also observed under SEM in order to determine the presence of any cracks and whether it was a brittle or a ductile fracture. A correlation

  9. Final Report, Volume 4, The Development of Qualification Standards for Cast Super Duplex Stainless Steel (2507 Wrought Equivalent)

    Energy Technology Data Exchange (ETDEWEB)

    Hariharan, Vasudevan; Lundin, Carl, W.

    2005-09-30

    The objective of the program is to determine the suitability of ASTM A923 Standard Test methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic-Ferritic Stainless Steels for 25 Cr Cast Super Duplex Stainless Steels (ASTM A890-5A). Different tests were carried out on the materials procured from various steel foundries as stated in the ASTM A923. The foundries were designated as Foundry A, B, C and D. All the materials were foundry solution annealed. Materials from Foundry D were solution heat treated at The University of Tennessee also and then they were subjected to heat treatment schedule which was derived from the testing of wrought DSS to establish the A923 specification. This was possible because the material from the same heat was sufficient for conducting the full scope of heat treatment. This was done prior to carrying out various other tests. Charpy samples were machined. The Ferrite content was measured in all the Charpy samples using Feritscope® and ASTM E562 Manual Point Count Method. After the ferrite content was measured the samples were sent to AMC-Vulcan, Inc. in Alabama to conduct the Charpy impact test based on ASTM A923 Test Method B. This was followed by etch testing and corrosion analysis based on ASTM A923 Test Methods A and C respectively at University of Tennessee. Hardness testing using Rockwell B and C was also carried out on these samples. A correlation was derived between all the three test methods and the best method for evaluating the presence of intermetallic in the material was determined. The ferrite content was correlated with the toughness values. Microstructural analysis was carried out on the etch test samples using Scanning Electron Microscopy in order to determine if intermetallic phases were present. The fracture surfaces from Charpy test specimens were also observed under SEM in order to determine the presence of any cracks and whether it was a brittle or a ductile fracture. A correlation was

  10. Thermochemical surface engineering of steels

    DEFF Research Database (Denmark)

    Thermochemical Surface Engineering of Steels provides a comprehensive scientific overview of the principles and different techniques involved in thermochemical surface engineering, including thermodynamics, kinetics principles, process technologies and techniques for enhanced performance of steels...

  11. Cold formability of steels

    International Nuclear Information System (INIS)

    Lafond, G.; Leclerq, G.; Moliexe, F.; Namdar, R.; Roesch, L.; Sanz, G.

    1977-01-01

    This work was essentially aimed to the study of the following three questions. Is it possible to assess the cold formability of steels using simple material properties as criteria. What values of mechanical properties can one expect to reach in cold formed parts. Are there simple ways of characterizing the speroidization treatments carried out on steels before cold forming operations. The present report describes the results obtained during this investigation. It is logically divided into three separate parts. Experimental study of cold formability in wire drawing. Influence of metallurgical variables on mechanical properties of high carbon cold drawn wires. Contribution to the study of characterization methods of cold forming steels subjected to a spheroidization heat treatment

  12. Possibilities of utilization of fly ash from the black coal Power Engineering of the U. S. Steel Košice

    Directory of Open Access Journals (Sweden)

    Františka Michalíková

    2005-11-01

    Full Text Available The paper presents modes of a direct utilization of the fly ash by-product of the combustion of black power coal in the slag - bottom boilers of the Division Plant Power Engineering ( DP PE of the U. S. Steel Košice ( next USSK . The properties of fly ash limit its use in metallurgy and foundry industry. The fly ash is directly utilizable in the metallurgical industry as a component of powder cover mixtures and insulation inserts, heat insulation parts and exothermical mixtures. The most important components in the mixtures are light micro spheres – cenospheres and heavy micro spheres – plerospheres. The micro spheres significantly improve properties of the powder cover mixtures.

  13. National steel tries wheeling

    International Nuclear Information System (INIS)

    Dudak, J.R.

    1992-01-01

    In 1989, National Steel felt the need to take the next step to make its Detroit-based division, Great Lakes Steel, more competitive in the world flat-rolled steel market. In 1988, Great Lakes Steel started flowing natural gas through the first fully litigated bypass (Competitive Sourcing Option) of a local distribution company. In 1989, the second connection with the new supply route for gas transportation, Panhandle Eastern had started flowing and the LDC, Michigan Consolidated Gas Co. (MichCon) had pulled out their piping previously serving the plants. Since we had been able to structure a fully reliable supply route, storage and balancing program for gas in the face of such strong opposition by the LDC, the author felt it was time to attack the next singularly sourced major commodity, electricity. Electricity, at this major integrated steel plant, represented approximately 7% of plant cost yearly. Yet being monopolized, Great Lakes Division (GLD) could not multiple source this commodity like it does with its other 93% of costs, except for labor (25% of the 93%). Multiple sourcing is done to bring competitive pressure to suppliers and to diversify supplies and protect plant operation in the event of failure by one supplier. This paper describes National Steel's strategy to reduce the cost of power, at the minimum of capital costs, the most expedient way possible, that does not sacrifice any major long-term potential cost improvements. The results show that competitively priced power is available across the mid-west, at prices well below many state regulated electric utilities, for at least 5 to 15 years, but with major obstacles in obtaining transmission access

  14. Volatilization from PCA steel alloy

    Energy Technology Data Exchange (ETDEWEB)

    Hagrman, D.L.; Smolik, G.R.; McCarthy, K.A.; Petti, D.A.

    1996-08-01

    The mobilizations of key components from Primary Candidate Alloy (PCA) steel alloy have been measured with laboratory-scale experiments. The experiments indicate most of the mobilization from PCA steel is due to oxide formation and spalling but that the spalled particles are large enough to settle rapidly. Based on the experiments, models for the volatization of iron, manganese, and cobalt from PCA steel in steam and molybdenum from PCA steel in air have been derived.

  15. Fatigue damage of steel components

    DEFF Research Database (Denmark)

    Fæster, Søren; Zhang, Xiaodan; Huang, Xiaoxu

    2014-01-01

    Railway rails and the inner ring in roller bearings in wind turbines are both experiencing steel-to-steel contact in small areas with huge loads resulting in extremely high stresses in the base materials......Railway rails and the inner ring in roller bearings in wind turbines are both experiencing steel-to-steel contact in small areas with huge loads resulting in extremely high stresses in the base materials...

  16. Report on NPPCI topics in the United Kingdom - March 1986

    International Nuclear Information System (INIS)

    Cox, R.J.

    1986-01-01

    The author reviews the activities on nuclear power plant instrumentation and control topics in the United Kingdom. Since the last meeting of the Working Group in May 1984, the activities of the nuclear power industry in the United Kingdom has been dominated, firstly, by the Public Inquiry into the proposal to site a PWR at Sizewell in Suffolk - the public part of the Inquiry finished about a year ago having lasted eighteen months but the report is not now expected for some months. Secondly, all of the first generation of Advanced Gas Cooled Reactors have run up to power. Thirdly, the Prototype Fast Reactor at Dounreay is now reliably producing its design output of 250 MW(e) following major modifications to its steam generators. The new developments of the NPP simulators, computer control and instrumentation systems as well as reactor protection systems are briefly discussed

  17. Religious Activities and their Tourism Potential in Sukur Kingdom, Nigeria

    Directory of Open Access Journals (Sweden)

    Emeka Okonkwo

    2015-07-01

    Full Text Available Religious tourism is a form of tourism whereby people of the same faith travel individually or in groups for religious purposes. This form of tourism comprises many facets of the travel industry ranging from pilgrimages, missionary travel, leisure (fellowship, vacations, faith-based cruising, crusades, conventions and rallies, retreats, monastery visits and guest-stays, Christian and faith-based camps, to religious tourist attractions. In Sukur Kingdom, most tourists embark on religious travel for the primary purpose of sharing faith and fellowship together as they explore the various religious sites within Sukur and Adamawa State at large. Others still seek inspiration and desire to witness significant religious events while assisting others with humanitarian and spiritual needs. This paper examines the tourism potentials of religion/religious sites and belief systems in Sukur Kingdom with a view to harnessing them for sustainable tourism development. The study uses ethnographic methods to elicit information and analyze the data collected from respondents.

  18. Thermally Stable Nanocrystalline Steel

    Science.gov (United States)

    Hulme-Smith, Christopher Neil; Ooi, Shgh Woei; Bhadeshia, Harshad K. D. H.

    2017-10-01

    Two novel nanocrystalline steels were designed to withstand elevated temperatures without catastrophic microstructural changes. In the most successful alloy, a large quantity of nickel was added to stabilize austenite and allow a reduction in the carbon content. A 50 kg cast of the novel alloy was produced and used to verify the formation of nanocrystalline bainite. Synchrotron X-ray diffractometry using in situ heating showed that austenite was able to survive more than 1 hour at 773 K (500 °C) and subsequent cooling to ambient temperature. This is the first reported nanocrystalline steel with high-temperature capability.

  19. Joining uranium to steel

    International Nuclear Information System (INIS)

    Perkins, M.A.

    1976-05-01

    A method has been devised which will allow the joining of uranium to steel by fusion welding through the use of an intermediate material. Uranium-0.5 titanium was joined to AISI 304L stainless steel by using a vanadium insert. Also, a method is now available for selecting possible filler metals when two entirely dissimilar metals need to be joined. This method allows a quantitative ranking to be made of the possible filler metals and thus the most likely candidate can be selected

  20. "Does a Compensation Culture Exist in the United Kingdom?"

    OpenAIRE

    Harvey, Edward

    2008-01-01

    Abstract This dissertation investigates the issue of compensation culture and the evidence for it in the United Kingdom. Insight into the relationship between Tort Law and Insurance finds that the role of insurance is largely misinterpreted in the field. Insurance companies have many mechanisms to control behaviour, ensure personal responsibility is upheld, reduce moral hazard and promote risk management. This paper proposes that claims increases might be more evident in areas of compensa...

  1. Exploring support for shale gas extraction in the United Kingdom

    OpenAIRE

    Andersson-Hudson, Jessica; Knight, Wil; Humphrey, Mathew; O'Hara, Sarah

    2016-01-01

    The development of shale gas in the United Kingdom (UK) using hydraulic fracturing, more commonly known as ‘fracking’, remains in its infancy. Yet understanding public attitudes for this fledgling industry is important for future policy considerations, decision-making and for industry stakeholders. This study uses data collected from the University of Nottingham UK nationwide online survey (n=3,823) conducted in September 2014, to consider ten hypothesises about the UK public’s attitudes towa...

  2. Religious Activities and their Tourism Potential in Sukur Kingdom, Nigeria

    OpenAIRE

    Emeka Okonkwo

    2015-01-01

    Religious tourism is a form of tourism whereby people of the same faith travel individually or in groups for religious purposes. This form of tourism comprises many facets of the travel industry ranging from pilgrimages, missionary travel, leisure (fellowship), vacations, faith-based cruising, crusades, conventions and rallies, retreats, monastery visits and guest-stays, Christian and faith-based camps, to religious tourist attractions. In Sukur Kingdom, most tourists embark on religious trav...

  3. The status of podiatry in the United Kingdom.

    Science.gov (United States)

    Mandy, Phil

    2008-12-01

    This paper reviews the sources of professional status and analyses these in relation to the podiatry profession in the United Kingdom. It is argued that the nature and act of professional practice and the patient/professional relationship are of particular importance in defining the status of the profession. These effects are discussed in relation to podiatry and compared to a high status professional group, that of dentistry. Finally the effects of attempting to change professional status are discussed.

  4. Nitrogen-alloyed martensitic steels

    International Nuclear Information System (INIS)

    Berns, H.

    1988-01-01

    A report is presented on initial results with pressure-nitrided martensitic steels. In heat-resistant steels, thermal stability and toughness are raised by nitrogen. In cold work steel, there is a more favourable corrosion behaviour. (orig./MM) [de

  5. CULTURAL IMPORTANCE OF CHEESE TYPE FOR KINGDOM PERNAMBUCANO

    Directory of Open Access Journals (Sweden)

    Neide Kazue Sakugawa Shinohara

    2015-03-01

    Full Text Available Cheese is one of the great achievements in the preservation of milk, using simple techniques and preserving important protein source in different food crops. Originally from the Netherlands, Edam cheese was introduced in Brazil in 1880 by the Portuguese colonizers, hence the name "kingdom." Currently, in the industrial production, the legislation determines that it is classified as "kingdom type ". Due to the high lipid and sodium content, this product that is most suitable in the composition of sandwiches, in sauces added to pasta and composition along with the desserts, these associations are part of the tradition, flavors and knowledge of Pernambuco’s cooking. A ball of Kingdom cheese is something that you have to give to families, especially in Christmas time and St. John, because it symbolizes the wish for happiness and prosperity in the northeastern important religious festivals calendar, where relatives and friends gather to celebrate the dates in question, putting on their tables this precious culinary heritage of Pernambuco.

  6. Microbial-Influenced Corrosion of Corten Steel Compared with Carbon Steel and Stainless Steel in Oily Wastewater by Pseudomonas aeruginosa

    Science.gov (United States)

    Mansouri, Hamidreza; Alavi, Seyed Abolhasan; Fotovat, Meysam

    2015-07-01

    The microbial corrosion behavior of three important steels (carbon steel, stainless steel, and Corten steel) was investigated in semi petroleum medium. This work was done in modified nutrient broth (2 g nutrient broth in 1 L oily wastewater) in the presence of Pseudomonas aeruginosa and mixed culture (as a biotic media) and an abiotic medium for 2 weeks. The behavior of corrosion was analyzed by spectrophotometric and electrochemical methods and at the end was confirmed by scanning electron microscopy. The results show that the degree of corrosion of Corten steel in mixed culture, unlike carbon steel and stainless steel, is less than P. aeruginosa inoculated medium because some bacteria affect Corten steel less than other steels. According to the experiments, carbon steel had less resistance than Corten steel and stainless steel. Furthermore, biofilm inhibits separated particles of those steels to spread to the medium; in other words, particles get trapped between biofilm and steel.

  7. Guns, Germs and Steel

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 6; Issue 1. Guns, Germs and Steel - A Short History of Everybody for the Last 13,000 years. Suri Venkatachalam. Book Review Volume 6 Issue 1 January 2001 pp 84-88. Fulltext. Click here to view fulltext PDF. Permanent link:

  8. Underwater welding of steel

    International Nuclear Information System (INIS)

    Ibarra, S.; Olson, D.L.

    1992-01-01

    A fundamental basis to understand the behavior of wet underwater welding of steel is introduced. Both the pyrometallurgical and physical metallurgy concepts are discussed. Modifications of welding consumables and practice are suggested. This chapter promotes further contributions of meatllurgical research to improve and promote wet underwater welding. (orig.)

  9. Japan steel mill perspective

    Energy Technology Data Exchange (ETDEWEB)

    Murase, K. [Kobe Steel Ltd., Tokyo (Japan)

    2004-07-01

    The international and Japan's steel industry, the coking coal market, and Japan's expectations from Canada's coal industry are discussed. Japan's steel mills are operating at full capacity. Crude steel production for the first half of 2004 was 55.8 million tons. The steel mills are profitable, but costs are high, and there are difficulties with procuring raw materials. Japan is trying to enhance the quality of coke, in order to achieve higher productivity in the production of pig iron. Economic growth is rising disproportionately in the BRICs (Brazil, Russia, India, and China), with a large increase in coking coal demand from China. On the supply side, there are several projects underway in Australia and Canada to increase production. These include new developments by Elk Valley Coal Corporation, Grande Cache Coal, Western Canadian Coal, and Northern Energy and Mining in Canada. The Elga Mine in the far eastern part of Russia is under development. But the market is expected to remain tight for some time. Japan envisions Canadian coal producers will provide a stable coal supply, expansion of production and infrastructure capabilities, and stabilization of price. 16 slides/overheads are included.

  10. On choice of tempered steels

    International Nuclear Information System (INIS)

    Govorov, A.A.; Pan'shin, I.F.; Rakhmanov, V.I.

    1978-01-01

    For the purpose of developing a graphical method for choosing structural steels, a change in the propagation work of a crack and in the critical temperature of brittleness of 40, 40Kh, 40KhN, and 40KhNM steels, was examined depending on the hardness after hardening and tempering. A diagram enabling to choose the grade of steel for making an article of known dimensions according to the preset values of its mechanical properties has been plotted. The developed selection scheme takes into account the hardenability of steels and the influence of the hardness after thermal treatment on the cold-shortness of steel

  11. Challenges in Special Steel Making

    Science.gov (United States)

    Balachandran, G.

    2018-02-01

    Special bar quality [SBQ] is a long steel product where an assured quality is delivered by the steel mill to its customer. The bars have enhanced tolerance to higher stress application and it is demanded for specialised component making. The SBQ bars are sought for component making processing units such as closed die hot forging, hot extrusion, cold forging, machining, heat treatment, welding operations. The final component quality of the secondary processing units depends on the quality maintained at the steel maker end along with quality maintained at the fabricator end. Thus, quality control is ensured at every unit process stages. The various market segments catered to by SBQ steel segment is ever growing and is reviewed. Steel mills need adequate infrastructure and technological capability to make these higher quality steels. Some of the critical stages of processing SBQ and the critical quality maintenance parameters at the steel mill in the manufacture has been brought out.

  12. Automação industrial e sistemas informatizados de gestão da produção em fundições de mercado Industrial automation and computerized production management systems in make-to-order foundries

    Directory of Open Access Journals (Sweden)

    Flavio Cesar F. Fernandes

    2002-12-01

    Full Text Available Fundição é um processo de fabricação que vem crescendo em importância. O principal objetivo deste artigo é analisar, em termos de automação e sistemas informatizados de gestão da produção (SIGP, as fundições de mercado (fundições que produzem sob encomenda um grande número de pedidos vindos, em geral, de um grande número de clientes no interior do Estado de São Paulo pertencentes aos 5 principais pólos (Piracicaba, Indaiatuba, Limeira, São Carlos e Itu com 10 a 250 trabalhadores. Das 61 empresas do interior de São Paulo, 35 situam-se nesses 5 pólos (ou em suas imediações; entrevistamos pessoalmente os diretores industriais e visitamos o chão de fábrica de 30 fundições dentre essas 35. Analisamos quase 200 tabelas de freqüência e de contingência e extraímos várias conclusões, por exemplo: (i entre os três principais problemas e necessidades relativos à produção, dois deles estão diretamente relacionados com a automação industrial e com os SIGP; (ii são coincidentes os interesses em automação e SIGP.Foundry is a manufacturing process with a growing importance. The main objective of this paper is to analyze, in terms of automation and of computerized production management systems (CPMS, the make-to-order foundry in the interior of the state of São Paulo belonging to 5 main foundry industrial districts (Piracicaba, Indaiatuba, Limeira, São Carlos and Itu with 10 to 250 workers. From the 61 enterprises in the interior of São Paulo State, 35 are situated in these 5 industrial districts (or in their neighborhood; we interviewed personally the industrial executive officer and visited the shop-floor of 30 among this 35 foundries. We have analyzed almost 200 frequency and contingency tables and draw several conclusions, for example: (i among the three main problems and necessities related with production, two of them are directly related with automation and CPMS; (ii automation and CPMS generate coincident

  13. Heat Treatment and Properties of Iron and Steel

    National Research Council Canada - National Science Library

    Digges, Thomas

    1966-01-01

    .... Chemical compositions, heat treatments, and some properties and uses are presented for structural steels, tool steels, stainless and heat-resisting steels, precipitation-hardenable stainless steels...

  14. Steel for nuclear applications

    International Nuclear Information System (INIS)

    Zorev, N.N.; Astafiev, A.A.; Loboda, A.S.

    1978-01-01

    A steel contains, in percent by weight, the following constituents: carbon from 0.13 to 0.18, silicon from 0.17 to 0.37, manganese from 0.30 to 0.60, chromium from 1.7 to 2.4, nickel from 1.0 to 1.5, molybdenum from 0.5 to 0.7, vanadium from 0.05 to 0.12, aluminium from 0.01 to 0.035, nitrogen from 0.05 to 0.012, copper from 0.11 to 0.20, arsenic from 0.0035 to 0.0055, iron and impurities, the balance. This steel is preferable for use in the manufacture of nuclear reactors. 1 table

  15. Advances in stainless steels

    International Nuclear Information System (INIS)

    Baldev Raj; Jayakumar, T.; Saibaba, Saroja; Sivaprasad, P.V.; Shankar, P.

    2010-01-01

    This book covers a broad spectrum of topics spanning the entire life cycle of stainless steel-from alloy design and characterization to engineering design, fabrication, mechanical properties, corrosion, quality assurance of components, in-service performance assessment, life prediction and finally failure analysis of materials and components. The contents provide useful feedback for further developments aimed at effective utilization of this class of materials. The book comprises articles that bring out contemporary developments in stainless steels and is thematically classified into the following sections. 1. Component design, modelling and structural integrity, 2. Manufacturing technology, 3. Property evaluation, 4. Alloy development and applications, 5. NDE methods, 6. Corrosion and surface modification. The book commences with articles on component design and structural integrity, thus opening up the areas of challenge for researchers and academia. The articles in the book relevant to INIS are indexed separately

  16. Steel containment buckling

    International Nuclear Information System (INIS)

    Bennett, J.G.; Fly, G.W.; Baker, W.E.

    1984-01-01

    The Steel Containment Buckling program is in its fourth phase of work directed at the evaluation of the effects of the structural failure mode of steel containments when the membrane stresses are compressive. The structural failure mode for this state of stress is instability or buckling. The program to date has investigated: (1) the effect on overall buckling capacity of the ASME area replacement method for reinforcing around circular penetrations; (2) a set of benchmark experiments on ring-stiffened shells having reinforced and framed penetrations; (3) large and small scale experiments on knuckle region buckling from internal pressure and post-buckling behavior to failure for vessel heads having torispherical geometries; and (4) buckling under time-dependent loadings (dynamic buckling). The first two investigations are complete, the knuckle buckling experimental efforts are complete with data analysis and reporting in progress, and the dynamic buckling experimental and analytical work is in progress

  17. Steel containment buckling

    International Nuclear Information System (INIS)

    Butler, T.A.; Baker, W.E.

    1986-01-01

    Two aspects of buckling of a free-standing nuclear steel containment building were investigated in a combined experimental and analytical program. In the first part of the study, the response of a scale model of a containment building to dynamic base excitation is investigated. A simple harmonic signal was used for preliminary studies followed by experiments with scaled earthquake signals as the excitation source. The experiments and accompanying analyses indicate that the scale model response to earthquake-type excitations is very complex and that current analytical methods may require a dynamic capacity reduction factor to be incorporated. The second part of the study quantified the effects of framing at large penetrations on the static buckling capacity of scale model containments. Results show little effect from the framing for the scale models constructed from the polycarbonate, Lexan. However, additional studies with a model constructed of the prototypic steel material are suggested

  18. Conspicuous and aposematic spines in the animal kingdom

    Science.gov (United States)

    Inbar, Moshe; Lev-Yadun, Simcha

    2005-04-01

    Spines serve as a common physical defence mechanism in both the plant and animal kingdoms. Here we argue that as in plants, defensive animal spines are often conspicuous (shape and colour) and should be considered aposematic. Conspicuous spines may evolve as signals or serve as a cue for potential predators. Spine conspicuousness in animals has evolved independently across and within phyla occupying aquatic and terrestrial ecosystems, indicating that this convergent phenomenon is highly adaptive. Still, many spines are cryptic, suggesting that conspicuity is not simply constrained by developmental factors such as differences in the chemical composition of the integument. Aposematism does not preclude the signalling role of conspicuous spines in the sexual arena.

  19. Cultural differences between construction professionals in Denmark and United Kingdom

    DEFF Research Database (Denmark)

    Hancock, M.R.

    /Building Surveyors in relation to the Services Procurement Directive of the European Union. It is recommended that further studies be undertaken in order to develop a cultural profiling model and methods for the building sector to help identify areas of potential conflicts. The report is aimed at construction......This report presents the results of an investigation into cultural differences between professional members of the construction sector of Denmark and the United Kingdom. In particular it refers to differences between Arkitekter/Architects, Civilingeniører/Civil Engineers and Bygningskonstruktører...

  20. Nuclear power plant life extension in the United Kingdom

    International Nuclear Information System (INIS)

    Goodison, D.; Seddon, J.W.; Pape, E.M.

    1991-01-01

    The safety cases for the United Kingdom's older nuclear power plant have been reviewed by their utilities in order to justify continued operation of the reactors up to an age of at least 30 year. These 'long term safety reviews' have identified worthwhile plant modifications and aspects where further studies or plant inspections are required. As the plants approach the age of 30 years, 'life extension reviews' are now being undertaken, concentrating on management of ageing, to support operation to at least 40 years. (author)

  1. Chernobyl: response of medical physics departments in the United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Haywood, J K

    1986-01-01

    This conference drew attention to gaps in United Kingdom arrangements for dealing with the effects (both supposed and real) of accidents at civil nuclear installations on the populations which surround them; it showed how, in the case of the Chernobyl accident, Medical Physicists in the National Health Service responded to plug these gaps in spite of the organisational difficulties which the crisis presented; and it suggested a method of incorporating this hitherto underestimated resource into national planning for civil nuclear accidents. Reports are included from Newcastle, Charing Cross Hospital, The London Hospital, Cambridge, Westminster Hospital, Leeds, Liverpool, Cardiff, Canterbury, Swansea (environmental measurements) and Mount Vernon.

  2. Poultry litter power station in the United Kingdom

    International Nuclear Information System (INIS)

    Anon.

    1995-01-01

    Poultry litter has presented a waste disposal problem to the poultry industry in many parts of the United Kingdom. The plant at Eye is a small to medium scale power station, fired using poultry litter. The 12.7 MW of electricity generated is supplied, through the local utility, to the National Grid. The spent litter that constitutes the fuel is made up of excrement and animal bedding (usually 90% excrement and 10% straw or wood shavings). It comes from large climate-controlled buildings (broiler houses) where birds, reared for meat production, are allowed to roam freely. (UK)

  3. Nuclear energy and education in the United Kingdom

    International Nuclear Information System (INIS)

    Ginniff, M.E.

    1994-01-01

    The thesis of this paper is that sources of energy for a country must be dependable and their use from the production of the basic fuel to the disposal of the wastes should be up to standards which people can understand and accept. In the United Kingdom, the educational system is the source of basic information on sources of energy that are available and which sources are currently being developed to supply present and future energy needs. THe author provides a synopsis of educational techniques and materials which are used to educate the public about nuclear energy production

  4. COMPARISON OF REHABILITATION POLICIES IN LITHUANIA AND THE UNITED KINGDOM

    Directory of Open Access Journals (Sweden)

    Danguolė Jankauskienė

    2017-03-01

    Full Text Available The article analyses the formation, implementation and evaluation of rehabilitation policy in Lithuania and the United Kingdom through a comparative analysis and two empirical sociological qualitative studies. The following scientific problematic issues were raised: what is the situation in the field of rehabilitation policy formation, development and assessment in the historical perspective in Lithuania and the United Kingdom, what are the advantages and disadvantages of the implementation of rehabilitation policy in Lithuania and the UK, and what are the possibilities to change and improve the formation and implementation of rehabilitation policy. A comparative analysis of the principles of development, financing, legal regulation, advantages and disadvantages has been carried out, using scientific publications, reports, publications of foreign research papers, legal acts as well as qualitative researches of experts in Lithuania and the United Kingdom. Rehabilitation policies have been found to have similarities in the United Kingdom and Lithuania, but they are quite different as well. Lithuania developed its rehabilitation policy in a relatively short time in all areas of development amid a rapidly changing environment, with effective legal regulation, ambitious measures and limited resources. The United Kingdom’s rehabilitation policy has a much longer history; it changed in many ways to adapt to the needs of patients and society. It is based on the approach to the patient as an individual having a particular disorder, and the rehabilitation system promotes an individual rehab program in which the patient is an active participant and can even contribute to the plan, select services they need, and control the rehabilitation budget assigned to them. The system of rehabilitation policy between Lithuania and the UK varies considerably. In the UK, the focus is on the improvement of rehabilitation policy, working with communities, introducing

  5. Final Report, Volume 2, The Development of Qualification Standards for Cast Duplex Stainless Steel

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Steven, W.; Lundin, Carl, D.

    2005-09-30

    The scope of testing cast Duplex Stainless Steel (DSS) required testing to several ASTM specifications, while formulating and conducting industry round robin tests to verify and study the reproducibility of the results. ASTM E562 (Standard Test Method for Determining Volume Fraction by Systematic manual Point Count) and ASTM A923 (Standard Test Methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic/Ferritic Stainless Steels) were the specifications utilized in conducting this work. An ASTM E562 industry round robin, ASTM A923 applicability study, ASTM A923 industry round robin, and an ASTM A923 study of the effectiveness of existing foundry solution annealing procedures for producing cast DSS without intermetallic phases were implemented. In the ASTM E562 study, 5 samples were extracted from various cast austenitic and DSS in order to have varying amounts of ferrite. Each sample was metallographically prepared by UT and sent to each of 8 participants for volume fraction of ferrite measurements. Volume fraction of ferrite was measured using manual point count per ASTM E562. FN was measured from the Feritescope{reg_sign} and converted to volume fraction of ferrite. Results indicate that ASTM E562 is applicable to DSS and the results have excellent lab-to-lab reproducibility. Also, volume fraction of ferrite conversions from the FN measured by the Feritescope{reg_sign} were similar to volume fraction of ferrite measured per ASTM E562. In the ASTM A923 applicability to cast DSS study, 8 different heat treatments were performed on 3 lots of ASTM A890-4A (CD3MN) castings and 1 lot of 2205 wrought DSS. The heat treatments were selected to produce a wide range of cooling rates and hold times in order to study the suitability of ASTM A923 to the response of varying amounts on intermetallic phases [117]. The test parameters were identical to those used to develop ASTM A923 for wrought DSS. Charpy V-notch impact samples were extracted from the

  6. Final Report, Volume 2, The Development of Qualification Standards for Cast Duplex Stainless Steel

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Steven, W.; Lundin, Carl, W.

    2005-09-30

    The scope of testing cast Duplex Stainless Steel (DSS) required testing to several ASTM specifications, while formulating and conducting industry round robin tests to verify and study the reproducibility of the results. ASTM E562 (Standard Test Method for Determining Volume Fraction by Systematic manual Point Count) and ASTM A923 (Standard Test Methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic/Ferritic Stainless Steels) were the specifications utilized in conducting this work. An ASTM E562 industry round robin, ASTM A923 applicability study, ASTM A923 industry round robin, and an ASTM A923 study of the effectiveness of existing foundry solution annealing procedures for producing cast DSS without intermetallic phases were implemented. In the ASTM E562 study, 5 samples were extracted from various cast austenitic and DSS in order to have varying amounts of ferrite. Each sample was metallographically prepared by UT and sent to each of 8 participants for volume fraction of ferrite measurements. Volume fraction of ferrite was measured using manual point count per ASTM E562. FN was measured from the Feritescope® and converted to volume fraction of ferrite. Results indicate that ASTM E562 is applicable to DSS and the results have excellent lab-to-lab reproducibility. Also, volume fraction of ferrite conversions from the FN measured by the Feritescope® were similar to volume fraction of ferrite measured per ASTM E562. In the ASTM A923 applicability to cast DSS study, 8 different heat treatments were performed on 3 lots of ASTM A890-4A (CD3MN) castings and 1 lot of 2205 wrought DSS. The heat treatments were selected to produce a wide range of cooling rates and hold times in order to study the suitability of ASTM A923 to the response of varying amounts on intermetallic phases [117]. The test parameters were identical to those used to develop ASTM A923 for wrought DSS. Charpy V-notch impact samples were extracted from the castings and wrought

  7. Reactor pressure vessel steels

    International Nuclear Information System (INIS)

    Van De Velde, J.; Fabry, A.; Van Walle, E.; Chaouuadi, R.

    1998-01-01

    Research and development activities related to reactor pressure vessel steels during 1997 are reported. The objectives of activities of the Belgian Nuclear Research Centre SCK/CEN in this domain are: (1) to develop enhanced surveillance concepts by applying micromechanics and fracture-toughness tests to small specimens, and by performing damage modelling and microstructure characterization; (2) to demonstrate a methodology on a broad database; (3) to achieve regulatory acceptance and industrial use

  8. Reactor Pressure Vessel Steels

    Energy Technology Data Exchange (ETDEWEB)

    Van de Velde, J.; Fabry, A.; Van Walle, E.; Chaoudi, R

    1998-07-01

    SCK-CEN's R and D programme on Reactor Pressure Vessel (RPV) Steels in performed in support of the RVP integrity assessment. Its main objectives are: (1) to develop enhanced surveillance concepts by applying micromechanics and fracture-toughness tests to small specimens, and by performing damage modelling and microstructure characterization; (2) to demonstrate the applied methodology on a broad database; (3) to achieve regulatory acceptance and industrial use. Progress and achievements in 1999 are reported.

  9. Steele Richardson Olszewski syndrome

    Directory of Open Access Journals (Sweden)

    Vijayashree S Gokhale

    2013-01-01

    Full Text Available Parkinson′s disease and its plus syndromes are an important cause of morbidity in the geriatric age group. Its plus syndromes show a myriad of clinical features characterized by progressive symptoms. Here we present a 65-year-old woman with progressive "Parkinsonian-like features," i.e., mask-like face, slowness of all movements and tendency to fall, and difficulty in eye movements, leading to the diagnosis of Steele Richardson Olszewski Syndrome or progressive supranuclear palsy.

  10. Steels and welding nuclear

    International Nuclear Information System (INIS)

    Sessa, M.; Milella, P.P.

    1987-01-01

    This ENEA Data-Base regards mechanical properties, chemical composition and heat treatments of nuclear pressure vessel materials: type A533-B, A302-B, A508 steel plates and forgings, submerged arc welds and HAZ before and after nuclear irradiation. Irradiation experiments were generally performed in high flux material test reactors. Data were collected from international available literature about water nuclear reactors pressure vessel materials embrittlement

  11. Fracture Mechanisms in Steel Castings

    Directory of Open Access Journals (Sweden)

    Stradomski Z.

    2013-09-01

    Full Text Available The investigations were inspired with the problem of cracking of steel castings during the production process. A single mechanism of decohesion - the intergranular one - occurs in the case of hot cracking, while a variety of structural factors is decisive for hot cracking initiation, depending on chemical composition of the cast steel. The low-carbon and low-alloyed steel castings crack due to the presence of the type II sulphides, the cause of cracking of the high-carbon tool cast steels is the net of secondary cementite and/or ledeburite precipitated along the boundaries of solidified grains. Also the brittle phosphor and carbide eutectics precipitated in the final stage solidification are responsible for cracking of castings made of Hadfield steel. The examination of mechanical properties at 1050°C revealed low or very low strength of high-carbon cast steels.

  12. Hydrogen effects in stainless steel

    International Nuclear Information System (INIS)

    Caskey, G.R. Jr.

    1983-01-01

    The effects of hydrogen on stainless steels have been reviewed and are summarized in this paper. Discussion covers hydrogen solution and transport in stainless steels as well as the effects of hydrogen on deformation and fracture under various loading conditions. Damage is caused also by helium that arises from decay of the hydrogen isotope tritium. Austenitic, ferritic, martensite, and precipitation-hardenable stainless steels are included in the discussion. 200 references

  13. Mobilising for marine wind energy in the United Kingdom

    International Nuclear Information System (INIS)

    Jay, Stephen

    2011-01-01

    Since 2000, the United Kingdom has enthusiastically adopted marine wind energy as a potentially major source of electricity production and has become the leading nation in terms of output. This is in contrast to its relatively poor attainment of wind energy on land, and raises questions about the reasons for this difference in performance. This article traces the phases of development of marine wind energy in the UK with reference to factors that are instrumental in the uptake of this form of renewable energy. A number of features emerge from this analysis that stand in some contrast to the situation on land and help to explain the UK's current status. These include: recognition of an exceptional resource and relative ease of exploitation; government commitment and policy geared to controlled growth and strategic oversight, adequate economic support and start-up investment; the unusual rights and interests of the Crown Estate; and growing scale, confidence and organisation on the part of the industry. Set against these factors are the complexities of consenting, supply bottlenecks, and some stakeholder and public resistance, though these are outmatched by the drivers in favour of development and are being partly addressed. - Highlights: → The United Kingdom is demonstrating enthusiastic commitment to marine wind energy. → The features contributing to marine wind energy growth are analysed. → The UK has unique factors favouring the uptake of marine wind energy. → UK policy is geared to controlled growth and strategic oversight. → The Crown Estate's seabed rights and interests are a driver in implementation.

  14. Atmospheric polybrominated diphenyl ethers (PBDEs) in the United Kingdom

    International Nuclear Information System (INIS)

    Birgul, Askin; Katsoyiannis, Athanasios; Gioia, Rosalinda; Crosse, John; Earnshaw, Mark; Ratola, Nuno; Jones, Kevin C.; Sweetman, Andrew J.

    2012-01-01

    The occurrence of PBDEs has been studied in the atmosphere of four sites in the United Kingdom over a period of ten years. The concentrations have exhibited a sharp decrease after 2001–2003. This is evident in the urban sites of Manchester and London and at the semi-rural site of Hazelrigg. The average ΣPBDE half-lives for these three sites were 3.4, 2.0 and 3.5 years respectively. ΣPBDEs concentrations in the UK (in 2010 ΣPBDEs −3 ) are among the lowest reported in literature. Comparison of concentrations to estimated emissions and employment of PBDE profiles suggest that PBDEs in the UK atmosphere originate from primary emissions from products that contain mainly the penta-BDE technical mixture. The detection of BDE-183 in the majority of samples hints that octa-bromodiphenylether has also been used extensively in the UK, however to a smaller extent than the penta- product. PBDE levels have declined in the United Kingdom since 2000 in a manner that broadly supports national atmospheric emissions inventories.

  15. Indole: An evolutionarily conserved influencer of behavior across kingdoms.

    Science.gov (United States)

    Tomberlin, Jeffery K; Crippen, Tawni L; Wu, Guoyao; Griffin, Ashleigh S; Wood, Thomas K; Kilner, Rebecca M

    2017-02-01

    Indole is a key environmental cue that is used by many organisms. Based on its biochemistry, we suggest indole is used so universally, and by such different organisms, because it derives from the metabolism of tryptophan, a resource essential for many species yet rare in nature. These properties make it a valuable, environmental cue for resources almost universally important for promoting fitness. We then describe how indole is used to coordinate actions within organisms, to influence the behavior of conspecifics and can even be used to change the behavior of species that belong to other kingdoms. Drawing on the evolutionary framework that has been developed for understanding animal communication, we show how this is diversely achieved by indole acting as a cue, a manipulative signal, and an honest signal, as well as how indole can be used synergistically to amplify information conveyed by other molecules. Clarifying these distinct functions of indole identifies patterns that transcend different kingdoms of organisms. © 2016 WILEY Periodicals, Inc.

  16. Milled Die Steel Surface Roughness Correlation with Steel Sheet Friction

    DEFF Research Database (Denmark)

    Berglund, J.; Brown, C.A.; Rosén, B.-G.

    2010-01-01

    This work investigates correlations between the surface topography ofmilled steel dies and friction with steel sheet. Several die surfaces were prepared by milling. Friction was measured in bending under tension testing. Linear regression coefficients (R2) between the friction and texture...

  17. Heavy-metal contamination of soils in Saxony/Germany by foundry fumes and low-cost rapid analyses of contaminated soils by XRF

    Science.gov (United States)

    Mucke, D.

    2012-04-01

    Heavy-metal contamination of soils in Saxony/Germany by foundry fumes and low-cost rapid analysis of contaminated soils by XRF Dieter Mucke, Rolf Kumann, Sebastian Baldauf GEOMONTAN Gesellschaft für Geologie und Bergbau mbH&Co.KG, Muldentalstrasse 56, 09603 Rothenfurth, Saxony/Germany For hundreds of years in the Ore Mountains between Bohemia and Saxony silver and other ores are produced and smelted. Sulphide- and sulpharsenide-ores needed to be roasted first. In doing so the sulphide sulphur was oxidised under formation of sulphur dioxide SO2 and arsenide conversed into elemental arsenic and arsenide trioxide As2O3 respectively. Also the metals lead, cadmium and zinc are components of hut smokes, in the field of nickel foundries also nickel. The contents of soils basically reflect the geogenic conditions, which are caused by decomposition- and relocation-effects of the mineralisations, in the area of foundries also with influences by with the hut smokes anthropogenic mobilised elements. The Saxonian Agency for Environment and Geology drafted in 1992 a Soil Investigation Program with the aim of investigation of the contamination of Saxonian soils with arsenic and toxic heavy metals. In order of this Agency GEOMONTAN investigated 1164 measuring points in the grid 4 * 4 km.soil profiles and extracted soil samples for analysis. In the result of the laboratory examinations the Agency edited the "Soil atlas of the Free State of Saxony". 27 elements, pH and PAK are shown in detailed maps and allow in whole Saxony the first assessment of the contamination of soils with arsenic and toxic heavy metals. Each of the investigated soil profiles represent an area of 16 km2. Already by the different use of the districts (agricultural, industrial, urban) restricts representative values. GEOMONTAN in the meantime used at the exploration of a copper deposit in Brandenburg/Germany with approx. 50,000 single tests at drill cores a very fast low-cost method: the X Ray fluorescence

  18. Steels for nuclear power. I

    International Nuclear Information System (INIS)

    Bohusova, O.; Brumovsky, M.; Cukr, B.; Hatle, Z.; Protiva, K.; Stefec, R.; Urban, A.; Zidek, M.

    1976-01-01

    The principles are listed of nuclear reactor operation and the reactors are classified by neutron energy, fuel and moderator designs, purpose and type of moderator. The trend and the development of light-water reactor applications are described. The fundamental operating parameters of the WWER type reactors are indicated. The effect is discussed of neutron radiation on reactor structural materials. The characteristics are described of steel corrosion due to the contact of the steel with steam or sodium in the primary coolant circuit. The reasons for stress corrosion are given and the effects of radiation on corrosion are listed. The requirements and criteria are given for the choice of low-alloy steel for the manufacture of pressure vessels, volume compensators, steam generators, cooling conduits and containment. A survey is given of most frequently used steels for pressure vessels and of the mechanical and structural properties thereof. The basic requirements for the properties of steel used in the primary coolant circuit are as follows: sufficient strength in operating temperature, toughness, good weldability, resistance to corrosion and low brittleness following neutron irradiation. The materials are listed used for the components of light-water and breeder reactors. The production of corrosion-resistant steels is discussed with a view to raw materials, technology, steel-making processes, melting processes, induction furnace steel-making, and to selected special problems of the chemical composition of steels. The effects are mainly discussed of lead, bismuth and tin as well as of some other elements on hot working of high-alloy steels and on their structure. The problems of corrosion-resistant steel welding and of pressure vessel cladding are summed up. Also discussed is the question of the concept and safeguards of the safety of nuclear installation operation and a list is presented of most commonly used nondestructive materials testing methods. The current

  19. Steel designers' handbook

    CERN Document Server

    Gorenc, Branko; Tinyou, Ron

    2012-01-01

    The Revised 7th Edition of Steel Designers' Handbook is an invaluable tool for all practising structural, civil and mechanical engineers as well as engineering students at university and TAFE in Australia and New Zealand. It has been prepared in response to changes in the design Standard AS 4100, the structural Design Actions Standards, AS /ANZ 1170, other processing Standards such as welding and coatings, updated research as well as feedback from users. This edition is based on Australian Standard (AS) 4100: 1998 and subsequent amendments. The worked numerical examples in the book have been e

  20. 48 CFR 252.229-7006 - Value added tax exclusion (United Kingdom).

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Value added tax exclusion... CLAUSES Text of Provisions And Clauses 252.229-7006 Value added tax exclusion (United Kingdom). As prescribed in 229.402-70(f), use the following clause: Value Added Tax Exclusion (United Kingdom) (JUN 1997...

  1. The application of burnup credit for spent fuel operations in the United Kingdom

    International Nuclear Information System (INIS)

    Bowden, R.

    1998-01-01

    This paper begins by outlining the structure of the nuclear industry in the United Kingdom. It then sets out the methodology of burnup credit, and provides a brief discussion of the validation and robustness of the calculational route. This leads to a description of both the current and intended applications of burnup credit in the United Kingdom. (author)

  2. Supporting Minority Ethnic Children and Adolescents with Social, Emotional, and Behavioral Difficulties in the United Kingdom

    Science.gov (United States)

    Cooper, Paul

    2006-01-01

    The author addresses the mental health needs of ethnic minority children and young people in the United Kingdom and the services that are provided to support them. The author discusses the complex and distinctive pattern of ethnic minority distribution in the United Kingdom, along with a consideration of what is known about the mental health of…

  3. A STRATEGIC ASSESSMENT OF THE ONLINE SPORTS BETTING INDUSTRY IN THE UNITED KINGDOM

    OpenAIRE

    Skogman, Ville

    2015-01-01

    A strategic assessment of the sports betting industry in the United Kingdom. The dissertation focuses on the field of strategic management, through which it tries to identify the competitive advantage of three operators in the United Kingdom online sports betting market; Betfair Group plc, Bet365 and William Hill plc.

  4. Mortality in vegetarians and comparable nonvegetarians in the United Kingdom.

    Science.gov (United States)

    Appleby, Paul N; Crowe, Francesca L; Bradbury, Kathryn E; Travis, Ruth C; Key, Timothy J

    2016-01-01

    Vegetarians and others who do not eat meat have been observed to have lower incidence rates than meat eaters of some chronic diseases, but it is unclear whether this translates into lower mortality. The purpose of this study was to describe mortality in vegetarians and comparable nonvegetarians in a large United Kingdom cohort. The study involved a pooled analysis of data from 2 prospective studies that included 60,310 persons living in the United Kingdom, comprising 18,431 regular meat eaters (who ate meat ≥5 times/wk on average), 13,039 low (less-frequent) meat eaters, 8516 fish eaters (who ate fish but not meat), and 20,324 vegetarians (including 2228 vegans who did not eat any animal foods). Mortality by diet group for each of 18 common causes of death was estimated with the use of Cox proportional hazards models. There were 5294 deaths before age 90 in >1 million y of follow-up. There was no significant difference in overall (all-cause) mortality between the diet groups: HRs in low meat eaters, fish eaters, and vegetarians compared with regular meat eaters were 0.93 (95% CI: 0.86, 1.00), 0.96 (95% CI: 0.86, 1.06), and 1.02 (95% CI: 0.94, 1.10), respectively; P-heterogeneity of risks = 0.082. There were significant differences in risk compared with regular meat eaters for deaths from circulatory disease [higher in fish eaters (HR: 1.22; 95% CI: 1.02, 1.46)]; malignant cancer [lower in fish eaters (HR: 0.82; 95% CI: 0.70, 0.97)], including pancreatic cancer [lower in low meat eaters and vegetarians (HR: 0.55; 95% CI: 0.36, 0.86 and HR: 0.48; 95% CI: 0.28, 0.82, respectively)] and cancers of the lymphatic/hematopoietic tissue [lower in vegetarians (HR: 0.50; 95% CI: 0.32, 0.79)]; respiratory disease [lower in low meat eaters (HR: 0.70; 95% CI: 0.53, 0.92)]; and all other causes [lower in low meat eaters (HR: 0.74; 95% CI: 0.56, 0.99)]. Further adjustment for body mass index left these associations largely unchanged. United Kingdom-based vegetarians and

  5. The industrial ecology of steel

    Energy Technology Data Exchange (ETDEWEB)

    Considine, Timothy J.; Jablonowski, Christopher; Considine, Donita M.M.; Rao, Prasad G.

    2001-03-26

    This study performs an integrated assessment of new technology adoption in the steel industry. New coke, iron, and steel production technologies are discussed, and their economic and environmental characteristics are compared. Based upon detailed plant level data on cost and physical input-output relations by process, this study develops a simple mathematical optimization model of steel process choice. This model is then expanded to a life cycle context, accounting for environmental emissions generated during the production and transportation of energy and material inputs into steelmaking. This life-cycle optimization model provides a basis for evaluating the environmental impacts of existing and new iron and steel technologies. Five different plant configurations are examined, from conventional integrated steel production to completely scrap-based operations. Two cost criteria are used to evaluate technology choice: private and social cost, with the latter including the environmental damages associated with emissions. While scrap-based technologies clearly generate lower emissions in mass terms, their emissions of sulfur dioxide and nitrogen oxides are significantly higher. Using conventional damage cost estimates reported in the literature suggests that the social costs associated with scrap-based steel production are slightly higher than with integrated steel production. This suggests that adopting a life-cycle viewpoint can substantially affect environmental assessment of new technologies. Finally, this study also examines the impacts of carbon taxes on steel production costs and technology choice.

  6. Stainless steels low temperature nitriding

    International Nuclear Information System (INIS)

    Roux, T.; Darbeida, A.; Von Stebut, J.; Michel, H.; Lebrun, J.P.; Hertz, D.

    1995-01-01

    Nitrogen ions implantation of 316L stainless steel leads to monophasic diffusion layers, which are constituted of a solid solution (γ N ) fcc, metastable, nitrogen sur-saturated, and without order. This article shows that for 316L stainless steels,these layers improve the tribological properties without degradation of the corrosion resistance. (A.B.). 13 refs. 6 figs

  7. Metadynamic recrystallization in C steels

    Indian Academy of Sciences (India)

    Unknown

    EN24 and EN2 steels, a drop from 4000 s to 6 s for similar temperature rise was observed. Metadynamic ... carbon–manganese or silicon–manganese steels, but stops after a reduction at ... growth by strain-induced grain boundary migration;.

  8. Mechanics in Steels through Microscopy

    NARCIS (Netherlands)

    Tirumalasetty, G.K.

    2013-01-01

    The goal of the study consolidated in this thesis is to understand the mechanics in steels using microscopy. In particular, the mechanical response of Transformation Induced Plasticity (TRIP) steels is correlated with their microstructures. Chapter 1 introduces the current state of the art of TRIP

  9. A Tale of Wootz Steel

    Indian Academy of Sciences (India)

    manufacture of steel in south India by a crucible process at ... indicates that the production of wootz steel was almost on an industrial scale in ... in an Age of Design marked by ... The Russian Anasoff also studied the process of manufacturing.

  10. Irradiation creep in ferritic steels

    International Nuclear Information System (INIS)

    Vandermeulen, W.; Bremaecker, A. de; Burbure, S. de; Huet, J.J.; Asbroeck, P. van

    Pressurized and non-pressurized capsules of several ferritic steels have been irradiated in Rapsodie between 400 and 500 0 C up to 3.7 x 10 22 n/cm 2 (E>0.1 MeV). Results of the diameter measurements are presented and show that the total in-pile deformation is lower than for austenitic steels

  11. Steel structures for nuclear facilities

    International Nuclear Information System (INIS)

    1993-01-01

    In the guide the requirements concerning design and fabrication of steel structures for nuclear facilities and documents to be submitted to the Finnish Centre for Radiation and Nuclear Safety (STUK) are presented. Furthermore, regulations concerning inspection of steel structures during construction of nuclear facilities and during their operation are set forth

  12. Anti-carburizing Coating for Resin Sand Casting of Low Carbon Steel Based on Composite Silicate Powder Containing Zirconium

    Directory of Open Access Journals (Sweden)

    Zhan Chunyi

    2018-01-01

    Full Text Available This paper studied the structure and properties of anticarburizing coating based on composite silicate powder containing zirconium by X-ray diffraction analyzer, thermal expansion tester, digital microscope and other equipment. It is introduced that the application example of the coating in the resin-sand casting of ZG1Cr18Ni9Ti stainless steel impeller. The anti-carburizing effect of the coating on the surface layer of the cast is studied by using direct reading spectrometer and spectrum analyzer. The change of the micro-structure of the coating after casting and cooling is observed by scanning electron microscope. The analysis of anti-carburizing mechanism of the coating is presented. The results indicate that the coating possesses excellent suspension property, brush ability, permeability, levelling property and crackresistance. The coating exhibits high strength and low gas evolution. Most of the coating could be automatically stripped off flakily when the casting was shaken out. The casting possesses excellent surface finish and antimetal penetration effect. The carburizing layer thickness of the stainless steel impeller casting with respect to allowable upper limit of carbon content is about 1mm and maximum carburizing rate is 23.6%. The anticarburizing effect of casting surface is greatly improved than that of zircon powder coating whose maximum carburizing rate is 67.9% and the carburizing layer thickness with respect to allowable upper limit of carbon content is greater than 2mm. The composite silicate powder containing zirconium coating substantially reduces the zircon powder which is expensive and radioactive and mainly dependent on imports. The coating can be used instead of pure zircon powder coating to effectively prevent metal-penetration and carburizing of resin-sand-casting surface of low carbon steel, significantly improve the foundry production environment and reduce the production costs.

  13. Steels from materials science to structural engineering

    CERN Document Server

    Sha, Wei

    2013-01-01

    Steels and computer-based modelling are fast growing fields in materials science as well as structural engineering, demonstrated by the large amount of recent literature. Steels: From Materials Science to Structural Engineering combines steels research and model development, including the application of modelling techniques in steels.  The latest research includes structural engineering modelling, and novel, prototype alloy steels such as heat-resistant steel, nitride-strengthened ferritic/martensitic steel and low nickel maraging steel.  Researchers studying steels will find the topics vital to their work.  Materials experts will be able to learn about steels used in structural engineering as well as modelling and apply this increasingly important technique in their steel materials research and development. 

  14. Conservation of Planar Polarity Pathway Function Across the Animal Kingdom.

    Science.gov (United States)

    Hale, Rosalind; Strutt, David

    2015-01-01

    Planar polarity is a well-studied phenomenon resulting in the directional coordination of cells in the plane of a tissue. In invertebrates and vertebrates, planar polarity is established and maintained by the largely independent core and Fat/Dachsous/Four-jointed (Ft-Ds-Fj) pathways. Loss of function of these pathways can result in a wide range of developmental or cellular defects, including failure of gastrulation and problems with placement and function of cilia. This review discusses the conservation of these pathways across the animal kingdom. The lack of vital core pathway components in basal metazoans suggests that the core planar polarity pathway evolved shortly after, but not necessarily alongside, the emergence of multicellularity.

  15. A regulatory view of containment integrity in the United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Bradford, P M; Patchett, C M [Health and Safety Executive, Bootle (United Kingdom). Nuclear Installations Inspectorate

    1994-12-31

    This paper reviews the approach of HM Nuclear Installations Inspectorate (NII) to containment integrity in the United Kingdom (UK). NII is that part of the regulatory authority, the Health and Safety Executive (HSE), which administers the UK`s nuclear site licensing system. A major part of the licensing process lies in the assessment of licensees` submissions for new and existing plant. The purpose of this paper is to: briefly review our revised Safety Assessment Principles, describe our assessment and inspection activities on the primary containment building of the Sizewell B PWR which is progressing to full power operation in 1994 and, to indicate our views on the possible directions for future research into containment design and performance. (author). 5 refs.

  16. Alcohol and economic development: Observations on the kingdom of Bhutan.

    Science.gov (United States)

    Kypri, Kypros; Dorji, Gampo; Dalton, Craig

    2017-05-01

    Bhutan is a small country undergoing rapid social change arising from income growth, urbanisation and Western cultural influence. Markers of poverty, namely infectious disease and infant mortality, have improved dramatically. The attention of health authorities is now focused on the non-communicable disease and injury burdens, to which alcohol consumption is a major contributor. The paper draws on official data to characterise the consumption of alcohol and related harm, and the nature of the alcohol market, with commentary on crucial aspects of availability policies and drink-driving regulation that need reform. Kypri K, Dorji G, Dalton C. Alcohol and economic development: Observations on the kingdom of Bhutan. Drug Alcohol Rev 2017;36:333ȃ336.]. © 2016 Australasian Professional Society on Alcohol and other Drugs.

  17. The management of household hazardous waste in the United Kingdom.

    Science.gov (United States)

    Slack, R J; Gronow, J R; Voulvoulis, N

    2009-01-01

    Waste legislation in the United Kingdom (UK) implements European Union (EU) Directives and Regulations. However, the term used to refer to hazardous waste generated in household or municipal situations, household hazardous waste (HHW), does not occur in UK, or EU, legislation. The EU's Hazardous Waste Directive and European Waste Catalogue are the principal legislation influencing HHW, although the waste categories described are difficult to interpret. Other legislation also have impacts on HHW definition and disposal, some of which will alter current HHW disposal practices, leading to a variety of potential consequences. This paper discusses the issues affecting the management of HHW in the UK, including the apparent absence of a HHW-specific regulatory structure. Policy and regulatory measures that influence HHW management before disposal and after disposal are considered, with particular emphasis placed on disposal to landfill.

  18. Oil and Gas Emergency Policy: United Kingdom 2010 update

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    This publication provides a detailed look at the specific systems in the United Kingdom for responding to an oil supply crisis. In 2007, the IEA published ''Oil Supply Security: Emergency Response of IEA Countries''. Rather than waiting for the completion of the current review cycle to renew this full publication, the IEA will provide updates to the country chapters as these become available following the specific country's review. The aim of series of publications is to provide an overview of the IEA oil emergency response system and a detailed look at the specific systems in each IEA country for responding to an oil supply crisis. The 2007 publication represented the findings of a five year review cycle of the emergency response mechanisms in IEA member countries. Since the 2007 publication, the IEA has started a new cycle of reviews which now includes reviewing gas emergency policies.

  19. A regulatory view of containment integrity in the United Kingdom

    International Nuclear Information System (INIS)

    Bradford, P.M.; Patchett, C.M.

    1994-01-01

    This paper reviews the approach of HM Nuclear Installations Inspectorate (NII) to containment integrity in the United Kingdom (UK). NII is that part of the regulatory authority, the Health and Safety Executive (HSE), which administers the UK's nuclear site licensing system. A major part of the licensing process lies in the assessment of licensees' submissions for new and existing plant. The purpose of this paper is to: briefly review our revised Safety Assessment Principles, describe our assessment and inspection activities on the primary containment building of the Sizewell B PWR which is progressing to full power operation in 1994 and, to indicate our views on the possible directions for future research into containment design and performance. (author). 5 refs

  20. Reclamation of abandoned underground mines in the United Kingdom

    International Nuclear Information System (INIS)

    Brook, D.

    1994-01-01

    Since 1980, the Derelict Land Grant program has supported reclamation of abandoned mines in the United Kingdom. The stabilization of large-scale limestone mines in the West Midlands has stimulated the development of new methods of bulk infilling using waste materials as thick pastes. Colliery spoil rock paste develops strengths of 10 to 20 kPa to support roof falls and prevent crown hole collapse. Pulverized fuel ash rock paste develops strengths over 1 MPa where lateral support to pillars is required. Smaller scale mine workings in the West Midlands and elsewhere have been stabilized using conventional grouting techniques, hydraulic and pneumatic stowing, foamed-concrete infill, bulk excavation with controlled backfill, and structural support using bolts, mesh, and shotcrete

  1. Nanoprecipitation in bearing steels

    International Nuclear Information System (INIS)

    Barrow, A.T.W.; Rivera-Diaz-del-Castillo, P.E.J.

    2011-01-01

    θ-phase is the main hardening species in bearing steels and appears in both martensitically and bainitically hardened microstructures. This work presents a survey of the microstrucural features accompanying nanoprecipitation in bearing steels. Nanoprecipitate structures formed in 1C-1.5Cr wt.% with additions of Cr, Mn, Mo, Si and Ni are studied. The work is combined with thermodynamic calculations and neural networks to predict the expected matrix composition, and whether this will transform martensitically or bainitically. Martensite tetragonality, composition and the amount of retained austenite are related to hardness and the type of nanoprecipitate structures in martensitic grades. The θ-phase volume fraction, the duration of the bainite to austenite transformation and the amount of retained austenite are related to hardness and a detailed quantitative description of the precipitate nanostructures. Such description includes compositional studies using energy-dispersive spectroscopy, which shows that nanoprecipitate formation takes place under paraequilibrium. Special attention is devoted to a novel two-step bainite tempering process which shows maximum hardness; we prove that this is the most effective process for incorporating solute into the precipitates, which are finer than those resulting from one-step banitic transformation processes.

  2. The struggle against climate change in the United Kingdom

    International Nuclear Information System (INIS)

    2009-01-01

    As the United Kingdom has been the first country in the world to adopt a law to struggle against climate change, The Climate Change Act 2008, which specifies a 80% reduction of greenhouse gas emissions by 2050 (vs 1990), this report propose an overview of the actions implemented by this country in the political, economical, and technological fields to struggle against climate change. The various organisations and political institutions concerned by this struggle are presented (governmental organisations and institutions, non governmental institutions). The content of the Climate Change Act is described: definitions of constraints and requirements, carbon reduction commitment (CRC), carbon budgets, systems and programmes dealing with energy production (Renewable Obligation, household energy supplier obligations), with firms (Climate Change Levy, Climate Change Agreements, Enhanced Capital Allowances), with transports (Renewable Transport Fuel Obligation, Low Carbon Vehicle Procurement Programme), with buildings (Low Carbon Building Programme, Home Energy Saving Programme), with research and communication. Then, discussing the economy of climate change, this report comments the content of the Stern report, the reactions about it, and the economical consequences of struggle against climate change. These consequences can be drawbacks (increase of energy costs, inequalities of abilities to face transition costs, loss of international competitiveness) or benefits. The consequences of the economical crisis are also briefly discussed, as well as the consequences of the solutions to this crisis. The third part of this report gives an overview of the low carbon engineering and technology in the United Kingdom in the energy sector (renewable energy, wind energy, hydroelectric energy, biomass, nuclear energy, carbon capture and storage) and in the transport sector. The last part comments the objectives of the 2009 Copenhagen conference

  3. Competent authority approval of package designs in the United Kingdom

    International Nuclear Information System (INIS)

    Morgan-Warren, E.J.

    1999-01-01

    Type B packages and all packages containing fissile material, as well as special form radioactive materials, special arrangements and certain shipments, are required to be approved by the competent authority. In the United Kingdom competent authority approval is carried out on behalf of the Secretary of State by the Radioactive Materials Transport Division (RMTD) of the Department of the Environment, Transport and the Regions (DETR). Competent authority approval of a package design is given only after a detailed assessment of the design by the specialist staff of RMTD. There are three facets to the assessment procedure, namely engineering, criticality and radiation protection, and quality assurance. The engineering assessor ensures that the designer has demonstrated the integrity of the containment and shielding systems under the regulatory conditions. The criticality assessor examines criticality safety and radiation protection measures, and together with the engineering assessor, decides whether this is maintained under regulatory conditions. The quality assurance assessor verifies that the applicant has established the necessary controls to ensure that the design requirements are met. The applicant is responsible for making the case for approval, but the assessment is facilitated if the competent authority is involved with the designer at an early stage in development and during the construction of any test prototype. When a regulatory test programme is required, it is designed and carried out by the applicant, but agreed and witnessed by representatives of RMTD. Following the test programme, the applicant submits a formal application, supported by a design safety report (DSR). The DSR provides a full analysis of the design and the test results, including the behaviour of the package under normal and accident conditions of transport, the manufacturing and maintenance procedures, quality assurance and the emergency provisions for the operation of the package

  4. United Kingdom: Procurement Related Nuclear Experience (Operating Experience)

    International Nuclear Information System (INIS)

    2016-01-01

    Procurement of nuclear facilities in the United Kingdom is subject to nuclear site licence conditions issued by the Government through the Office for Nuclear Regulation (ONR). Each nuclear facility in the United Kingdom must have a nuclear site licence and must comply with the 36 general conditions that are set out in the Licence Condition Handbook (October 2014). In addition, the ONR has published a technical assessment guide for the procurement of nuclear safety related items or services; a guide on intelligent customers and a guide on records management also apply to the procurement phase, and ONR interventions look across all three of these documents. Procurement governance arrangements need to be developed (including a policy, manual, procedures and template documents) and approved within the utility company. The ONR monitors the arrangements via interventions and deems the arrangements to be ‘adequate’. Some procurement contracts become lifetime records for nuclear safety related systems and need to be retained while the plant is in place. A formal record retention schedule needs to be created and managed by the procurement organization. The utility company may elect to set hold points during the various procurement stages and, importantly, obtain approval for the contract and its content from all technical stakeholders (with particular emphasis on the engineering, project management and design authority quality functions before contract award). For contracts with high nuclear safety significance, the ONR may enforce additional hold points before and/or after contract award. There is a general requirement that the utility puts in place adequate arrangements to ensure that suitably qualified and experienced personnel are employed to implement adequate management arrangements and to act as an intelligent customer. This includes being able to demonstrate that any contractor or supplier is suitable, capable and experienced, and has the necessary processes and

  5. Fast-reactor fuel reprocessing in the United Kingdom

    International Nuclear Information System (INIS)

    Allardice, R.H.; Buck, C.; Williams, J.

    1977-01-01

    Enriched uranium metal fuel irradiated in the Dounreay Fast Reactor has been reprocessed and refabricated in plants specifically designed for the purpose in the United Kingdom since 1961. Efficient and reliable fuel recycle is essential to the development of a plutonium-based fast-reactor system, and the importance of establishing at an early stage fast-reactor fuel reprocessing has been reinforced by current world difficulties in reprocessing high-burnup thermal-reactor oxide fuel. The United Kingdom therefore decided to reprocess irradiated fuel from the 250MW(e) Prototype Fast Reactor (PFR) as an integral part of the fast reactor development programme. Flowsheet and equipment development work for the small-scale fully active demonstration plant has been carried out since 1972, and the plant will be commissioned and ready for active operation during 1977. In parallel, a comprehensive waste-management system has been developed and installed. Based on this development work and the information which will arise from active operation of the plant, a parallel development programme has been initiated to provide the basis for the design of a large-scale fast-reactor fuel-reprocessing plant to come into operation in the late 1980s to support the projected UK fast-reactor installation programme. The paper identifies the important differences between fast-reactor and thermal-reactor fuel-reprocessing technologies and describes some of the development work carried out in these areas for the small-scale PFR fuel-reprocessing operation. In addition, the development programme in aid of the design of a larger scale fast-reactor fuel-reprocessing plant is outlined and the current design philosophy discussed. (author)

  6. Energy policies of IEA countries: the United Kingdom 2006 review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-07-01

    The United Kingdom is facing a critical moment in its energy policy: North Sea oil and gas production is declining, dependence on imported energy is increasing, while rising energy prices and climate change considerations pose further challenges. The second thematic review of the UK addresses these challenges, focusing on energy investment, energy efficiency, and the return of nuclear power to the political agenda. Almost all coal-fired and nuclear power capacity in the United Kingdom will be retired within the next 15 years. The review encourages the government to maintain its trust in the market mechanism for the delivery of required investment and security of supply. However, it also identifies the need for the government to play a more active role in setting the framework. On the demand side, the IEA considers the government's 'Energy Efficiency Commitment' (EEC) an impressive success. The EEC was introduced in 2002 and is an energy-saving programme under which suppliers must achieve efficiency targets in households. Challenges, such as the requirement that 50 per cent of savings come from low-income households, remain, and the review invites the government to investigate ways in which fuel poverty could be reduced without distorting the EEC. The review also assesses the government's shifting direction on nuclear energy and backs this new path. It argues that the development of a positive investment framework in planning and licensing - without direct intervention in investment decisions favouring nuclear - will allow investors to judge the viability of new plants. 3 apps.

  7. Biodiversity: molecular biological domains, symbiosis and kingdom origins

    Science.gov (United States)

    Margulis, L.

    1992-01-01

    The number of extant species of organisms is estimated to be from fewer than 3 to more than 30 x 10(6) (May, 1992). Molecular biology, comparative genetics and ultrastructural analyses provide new insights into evolutionary relationships between these species, including increasingly precise ideas of how species and higher taxa have evolved from common ancestors. Accumulation of random mutations and large macromolecular sequence change in all organisms since the Proterozoic Eon has been importantly supplemented by acquisition of inherited genomes ('symbiogenesis'). Karyotypic alterations (polyploidization and karyotypic fissioning) have been added to these other mechanisms of species origin in plants and animals during the Phanerozoic Eon. The new evolution concepts (coupled with current rapid rates of species extinction and ignorance of the extent of biodiversity) prompted this analysis of the field of systematic biology and its role in the reorganization of extant species into higher taxa. Two superkingdoms (= Domains: Prokaryotae and Eukaryotae) and five kingdoms (Monera = Procaryotae or Bacteria; Protoctista: algae, amoebae, ciliates, foraminifera, oomycetes, slime molds, etc.; Mychota: 'true' fungi; Plantae: one phylum (division) of bryophytes and nine phyla of tracheophytes; and Animalia) are recognized. Two subkingdoms comprise the monera: the great diverse lineages are Archaebacteria and Eubacteria. The criteria for classification using molecular, ultrastructural and genetic data for this scheme are mentioned. For the first time since the nineteenth century, logical, technical definitions for each group are given with their time of appearance as inferred from the fossil record in the primary scientific literature. This classification scheme, which most closely reflects the evolutionary history, molecular biology, genetics and ultrastructure of extant life, requires changes in social organization of biologists, many of whom as botanists and zoologists, still

  8. The Evolution of Teleophthalmology Programs in the United Kingdom

    Science.gov (United States)

    Sim, Dawn A.; Mitry, Danny; Alexander, Philip; Mapani, Adam; Goverdhan, Srini; Aslam, Tariq; Tufail, Adnan; Egan, Catherine A.; Keane, Pearse A.

    2016-01-01

    Modern ophthalmic practice in the United Kingdom is faced by the challenges of an aging population, increasing prevalence of systemic pathologies with ophthalmic manifestations, and emergent treatments that are revolutionary but dependent on timely monitoring and diagnosis. This represents a huge strain not only on diagnostic services but also outpatient management and surveillance capacity. There is an urgent need for newer means of managing this surge in demand and the socioeconomic burden it places on the health care system. Concurrently, there have been exponential increases in computing power, expansions in the strength and ubiquity of communications technologies, and developments in imaging capabilities. Advances in imaging have been not only in terms of resolution, but also in terms of anatomical coverage, allowing new inferences to be made. In spite of this, image analysis techniques are still currently superseded by expert ophthalmologist interpretation. Teleophthalmology is therefore currently perfectly placed to face this urgent and immediate challenge of provision of optimal and expert care to remote and multiple patients over widespread geographical areas. This article reviews teleophthalmology programs currently deployed in the United Kingdom, focusing on diabetic eye care but also discussing glaucoma, emergency eye care, and other retinal diseases. We examined current programs and levels of evidence for their utility, and explored the relationships between screening, teleophthalmology, disease detection, and monitoring before discussing aspects of health economics pertinent to diabetic eye care. The use of teleophthalmology presents an immense opportunity to manage the steadily increasing demand for eye care, but challenges remain in the delivery of practical, viable, and clinically proven solutions. PMID:26830492

  9. Connections: Superplasticity, Damascus Steels, Laminated Steels, and Carbon Dating

    Science.gov (United States)

    Wadsworth, Jeffrey

    2016-12-01

    In this paper, a description is given of the connections that evolved from the initial development of a family of superplastic plain carbon steels that came to be known as Ultra-High Carbon Steels (UHCS). It was observed that their very high carbon contents were similar, if not identical, to those of Damascus steels. There followed a series of attempts to rediscover how the famous patterns found on Damascus steels blades were formed. At the same time, in order to improve the toughness at room temperature of the newly-developed UHCS, laminated composites were made of alternating layers of UHCS and mild steel (and subsequently other steels and other metals). This led to a study of ancient laminated composites, the motives for their manufacture, and the plausibility of some of the claims relating to the number of layers in the final blades. One apparently ancient laminated composite, recovered in 1837 from the great pyramid of Giza which was constructed in about 2750 B.C., stimulated a carbon dating study of ancient steels. The modern interest in "Bladesmithing" has connections back to many of these ancient weapons.

  10. Occupational Profiles in the European Steel Industry.

    Science.gov (United States)

    Franz, Hans-Werner; And Others

    The steel industry in Europe has faced great changes, with resulting layoffs and restructuring. Now that the most basic changes seem to be over, it has become evident that the remaining steel industry requires more highly trained workers than was the case previously. Although steel maintenance employees were always highly skilled, steel production…

  11. Methods of making bainitic steel materials

    Science.gov (United States)

    Bakas, Michael Paul; Chu, Henry Shiu-Hung; Zagula, Thomas Andrew; Langhorst, Benjamin Robert

    2018-01-16

    Methods of making bainitic steels may involve austenitizing a quantity of steel by exposing the quantity of steel to a first temperature. A composition of the quantity of steel may be configured to impede formation of non-bainite ferrite, pearlite, and Widmanstatten ferrite. The quantity of steel may be heat-treated to form bainite by exposing the quantity of steel to a second, lower temperature. The second, lower temperature may be stabilized by exposing the quantity of steel to the second, lower temperature in the presence of a thermal ballast.

  12. Stahlschüssel key to steel

    CERN Document Server

    Wegst, W S

    2016-01-01

    The Key to Steel (Stahlschlüssel/Stahlschluessel) cross reference book will help you to decode / decipher steel designations and find equivalent materials worldwide. The 2016 edition includes more than 70,000 standard designations and trade names from approximately 300 steelmakers and suppliers. Presentation is trilingual: English, French, and German. Materials covered include structural steels, tool steels, valve steels, high temperature steels and alloys, stainless and heat-resisting steels, and more. Standards and designations from 25 countries are cross-referenced.

  13. Advanced steel reheat furnace

    Energy Technology Data Exchange (ETDEWEB)

    Moyeda, D.; Sheldon, M.; Koppang, R. [Energy and Environmental Research Corp., Irvine, CA (United States); Lanyi, M.; Li, X.; Eleazer, B. [Air Products and Chemicals, Inc., Allentown, PA (United States)

    1997-10-01

    Energy and Environmental Research Corp. (EER) under a contract from the Department of Energy is pursuing the development and demonstration of an Advanced Steel Reheating Furnace. This paper reports the results of Phase 1, Research, which has evaluated an advanced furnace concept incorporating two proven and commercialized technologies previously applied to other high temperature combustion applications: EER`s gas reburn technology (GR) for post combustion NOx control; and Air Product`s oxy-fuel enrichment air (OEA) for improved flame heat transfer in the heating zones of the furnace. The combined technologies feature greater production throughput with associated furnace efficiency improvements; lowered NOx emissions; and better control over the furnace atmosphere, whether oxidizing or reducing, leading to better control over surface finish.

  14. Stainless steel decontamination manipulators

    International Nuclear Information System (INIS)

    Sullivan, R.J.

    1986-01-01

    Three, large-volume coverage manipulator systems were designed and built for the Defense Water Processing Facility at the Savannah River Laboratory. These stainless steel systems will be used for high-pressure spray decontamination of waste containers and large process equipment modules. Each system has a manipulator arm, folding boom, and vertical drive and guide structure. Handling capacity is 45 kg, horizontal reach is 4.6 m with a 180-deg swing motion, and the vertical travel is 6 m. The system is remotely removable and replaceable in modules using an overhead crane and an impact wrench. The manipulator arm has seven motions: Shoulder rotation and pivot, elbow pivot, wrist pivot and rotation, and grip open-close. All motions are variable speed and are slip-clutch protected to prevent overloading from external forces (collisions)

  15. Steel containment buckling

    International Nuclear Information System (INIS)

    Butler, T.A.; Baker, W.E.

    1987-01-01

    Two aspects of buckling of a free-standing nuclear containment building were investigated in a combined experimental and analytical program. In the first part of the study, the response of a scale model of a containment building to dynamic base excitation is investigated. A simple harmonic signal was used for preliminary studies followed by experiments with scaled earthquake signals as the excitation source. The experiments and accompanying analyses indicate that the scale model response to earthquake-type excitations is very complex and that current analytical methods may require that a dynamic capacity reduction factor be incorporated. The second part of the study quantified the effects of framing at large penetrations on the static buckling capacity of scale model containments. Results show little effect from the framing for the scale models constructed from the polycarbonate, Lexan. However, additional studies with a model constructed of the prototypic steel material are recommended. (orig.)

  16. Cold-formed steel design

    CERN Document Server

    Yu, Wei-Wen

    2010-01-01

    The definitive text in the field, thoroughly updated and expanded Hailed by professionals around the world as the definitive text on the subject, Cold-Formed Steel Design is an indispensable resource for all who design for and work with cold-formed steel. No other book provides such exhaustive coverage of both the theory and practice of cold-formed steel construction. Updated and expanded to reflect all the important developments that have occurred in the field over the past decade, this Fourth Edition of the classic text provides you with more of the detailed, up-to-the-minute techni

  17. Micropurity in stainless steel making

    International Nuclear Information System (INIS)

    Motloch, Z.

    1981-01-01

    New technologies were developed by the Vitkovice research institutes in response to high requirements for the quality of high-alloy steels for nuclear power, viz., duplex technology with double vacuum degassing at the DH unit and oxidation vacuum degassing using the VAKUVIT equipment. The steel produced shows low contents of impurities and high micropurity. A study was conducted into changes in carbon content and the formation of titanium nitrides and carbonitrides in austenitic steels during their production, and optimum technological parameters were found for eliminating their formation in forgings. (author)

  18. Steel fiber replacement of mild steel in prestressed concrete beams

    Science.gov (United States)

    2010-10-01

    In traditional prestressed concrete beams, longitudinal prestressed tendons serve to resist bending moment and : transverse mild steel bars (or stirrups) are used to carry shear forces. However, traditional prestressed concrete I-beams : exhibit earl...

  19. Steel fiber replacement of mild steel in prestressed concrete beams.

    Science.gov (United States)

    2011-01-01

    In traditional prestressed concrete beams, longitudinal prestressed tendons serve to resist bending moment and transverse mild : steel bars (or stirrups) are used to carry shear forces. However, traditional prestressed concrete I-beams exhibit early-...

  20. [The Steel factor].

    Science.gov (United States)

    Cáceres-Cortés, J R

    1997-01-01

    Mice bearing mutations at either of two loci, dominant White spotting(W) or Steel(Sl), exhibit development defects in hematopoietic, melanocytic and germ cells. Genetics studies have shown that the SI locus encodes the Steel factor (SF), which is the ligand for the tyrosine kinase receptor c-kit, the product of the W locus. SF is synthesized in membrane-bound form and can be processed to produce a soluble form. Cell-cell interaction is important in the production of normal blood cells in vivo and in vitro and in the cellular expansion of leukemic cells. We discuss here how SF decreases the requirements in cell interaction for blast colony formation in acute myeloblastic leukemia (AML) and the presence of membrane-bound SF possibly contributes to the density-dependent growth of the AML blasts. We explain that SF is mainly a survival factor for hematopoietic cells, of little proliferative effect, which maintains CD34+ hematopoietic cells in an undifferentiated state. These properties would potentially allow the maintenance of hematopoietic cells in culture for the purpose of marrow purging or gene therapy. The activation of the c-kit signal transduction pathway may play a significant role in the development of many types of non-hematological malignancies by disrupting normal cell-cell interactions and allowing the growth of cancer cell populations. In summary, the properties of the SF indicate it has a role for survival signals during the process of normal differentiation, AML proliferation and in the maintenance of many c-kit+ tumors.

  1. 2169 steel waveform experiments.

    Energy Technology Data Exchange (ETDEWEB)

    Furnish, Michael David; Alexander, C. Scott; Reinhart, William Dodd; Brown, Justin L.

    2012-11-01

    In support of LLNL efforts to develop multiscale models of a variety of materials, we have performed a set of eight gas gun impact experiments on 2169 steel (21% Cr, 6% Ni, 9% Mn, balance predominantly Fe). These experiments provided carefully controlled shock, reshock and release velocimetry data, with initial shock stresses ranging from 10 to 50 GPa (particle velocities from 0.25 to 1.05 km/s). Both windowed and free-surface measurements were included in this experiment set to increase the utility of the data set, as were samples ranging in thickness from 1 to 5 mm. Target physical phenomena included the elastic/plastic transition (Hugoniot elastic limit), the Hugoniot, any phase transition phenomena, and the release path (windowed and free-surface). The Hugoniot was found to be nearly linear, with no indications of the Fe phase transition. Releases were non-hysteretic, and relatively consistent between 3- and 5-mmthick samples (the 3 mm samples giving slightly lower wavespeeds on release). Reshock tests with explosively welded impactors produced clean results; those with glue bonds showed transient releases prior to the arrival of the reshock, reducing their usefulness for deriving strength information. The free-surface samples, which were steps on a single piece of steel, showed lower wavespeeds for thin (1 mm) samples than for thicker (2 or 4 mm) samples. A configuration used for the last three shots allows release information to be determined from these free surface samples. The sample strength appears to increase with stress from ~1 GPa to ~ 3 GPa over this range, consistent with other recent work but about 40% above the Steinberg model.

  2. THE DESTRUCTION OF THE ZULU KINGDOM: THE CIVIL WAR IN ZULULAND 1879-1884

    OpenAIRE

    D.H. Makobe

    2012-01-01

    The Destruction of the Zulu Kingdom: The civil war in Zululand 1879-1884, was originally submitted as a Ph.D dissertation in History at the University of London in 1975.Professor Jeff Guy, a well known historian on Zulu history and the present head of the History Department at the University of Natal, Durban branch has divided his work into three main parts. In the first part, entitled the "Invasion" he details the foundations of the Zulu Kingdom, the political structure of the Kingdom during...

  3. The keys of the kingdom as paradigm for building up the church in reformed church government

    Directory of Open Access Journals (Sweden)

    A. le R. du Plooy

    1998-06-01

    Full Text Available This article adopts an ecclesiological approach and concentrates on the prominent concepts the keys of the kingdom and building up the church. The article attempts to determine the significance those concepts may have for the government of the church and emphasises the close relationship between the keys of the kingdom and the building up of the church. According to Reformational viewpoints the administering of the keys serves the edification of the church. It becomes clear that the notae ecclesiae and the keys of the kingdom function as the basic elements of the church order and must be regarded as the basis or pillars upon which the church is built.

  4. Austenitic stainless steel weld inspection

    International Nuclear Information System (INIS)

    Mech, S.J.; Emmons, J.S.; Michaels, T.E.

    1978-01-01

    Analytical techniques applied to ultrasonic waveforms obtained from inspection of austenitic stainless steel welds are described. Experimental results obtained from a variety of geometric and defect reflectors are presented. Specifically, frequency analyses parameters, such as simple moments of the power spectrum, cross-correlation techniques, and adaptive learning network analysis, all represent improvements over conventional time domain analysis of ultrasonic waveforms. Results for each of these methods are presented, and the overall inspection difficulties of austenitic stainless steel welds are discussed

  5. High-strength maraging steels

    International Nuclear Information System (INIS)

    Grachev, S.V.; Shejn, A.S.

    1989-01-01

    Analysis of data on technological and operation properties of maraging steels on Fe-Cr-Ni, Fe-Ni, Fe-Cr-Co-Mo bases is given. Their advantages and drawbacks are pointed out. The scheme of strengthening heat treatment is considered. The fields of the most effective application of maraging steels for instance, for products operating under conditions of low-cycle and shock cyclic loading are mentioned

  6. Steel refining possibilities in LF

    Science.gov (United States)

    Dumitru, M. G.; Ioana, A.; Constantin, N.; Ciobanu, F.; Pollifroni, M.

    2018-01-01

    This article presents the main possibilities for steel refining in Ladle Furnace (LF). These, are presented: steelmaking stages, steel refining through argon bottom stirring, online control of the bottom stirring, bottom stirring diagram during LF treatment of a heat, porous plug influence over the argon stirring, bottom stirring porous plug, analysis of porous plugs disposal on ladle bottom surface, bottom stirring simulation with ANSYS, bottom stirring simulation with Autodesk CFD.

  7. MICROALLOYED STEELS FOR THE AUTOMOTIVE INDUSTRY

    Directory of Open Access Journals (Sweden)

    Debanshu Bhattacharya

    2014-12-01

    Full Text Available Two major drivers for the use of newer steels in the automotive industry are fuel efficiency and increased safety performance. Fuel efficiency is mainly a function of weight of steel parts, which in turn, is controlled by gauge and design. Safety is determined by the energy absorbing capacity of the steel used to make the part. All of these factors are incentives for the U.S. automakers to use both Highly Formable and Advanced High Strength Steels (AHSS to replace the conventional steels used to manufacture automotive parts in the past. AHSS is a general term used to describe various families of steels. The most common AHSS is the dual-phase steel that consists of a ferrite-martensite microstructure. These steels are characterized by high strength, good ductility, low tensile to yield strength ratio and high bake hardenability. Another class of AHSS is the complex-phase or multi-phase steel which has a complex microstructure consisting of various phase constituents and a high yield to tensile strength ratio. Transformation Induced Plasticity (TRIP steels is another class of AHSS steels finding interest among the U.S. automakers. These steels consist of a ferrite-bainite microstructure with significant amount of retained austenite phase and show the highest combination of strength and elongation, so far, among the AHSS in use. High level of energy absorbing capacity combined with a sustained level of high n value up to the limit of uniform elongation as well as high bake hardenability make these steels particularly attractive for safety critical parts and parts needing complex forming. A relatively new class of AHSS is the Quenching and Partitioning (Q&P steels. These steels seem to offer higher ductility than the dual-phase steels of similar strengths or similar ductility as the TRIP steels at higher strengths. Finally, martensitic steels with very high strengths are also in use for certain parts. The most recent initiative in the area of AHSS

  8. Solidification of Waste Steel Foudry Dust with Portland Cement

    Czech Academy of Sciences Publication Activity Database

    Škvára, F.; Kaštánek, František; Pavelková, I.; Šolcová, Olga; Maléterová, Ywetta; Schneider, Petr

    B89, č. 1 (2001), s. 67-81 ISSN 0304-3894 R&D Projects: GA ČR GA104/99/0440 Institutional research plan: CEZ:AV0Z4072921; CEZ:MSM 223100002 Keywords : solidification, * foundry dust * cement Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 0.497, year: 2001

  9. The management of animal bites in the United kingdom.

    Science.gov (United States)

    Evgeniou, E; Markeson, D; Iyer, S; Armstrong, A

    2013-01-01

    Animal bites represent a significant global health issue. The evidence in the literature regarding their management in many areas is conflicting and unclear. This project attempts to identify current evidence in the literature on the management of animal bites and assess if current practice in the United Kingdom is evidence based. A literature review on the management of animal bites was performed, and a national UK survey was contacted using a questionnaire based on the available evidence in the literature. The results from this survey show that 98% of plastic surgery units routinely use prophylactic antibiotics in all animal bite wounds; 58% close low-risk injuries primarily after initial washout, and there are conflicting opinions regarding the management of associated fractures and soft tissue injuries. The available data in the literature suggest that appropriate wound management is the most important factor for prevention of infection in animal bites. Antibiotic prophylaxis should only be given in high-risk wounds and primary closure should be performed in low-risk wounds. The management protocols of many plastic surgery units often diverge from the available evidence within the literature. On the basis of a thorough literature review, a guideline for the management of animal bites is presented. Future studies should investigate the management of associated fractures and soft tissue injuries.

  10. Darwinian sex roles confirmed across the animal kingdom.

    Science.gov (United States)

    Janicke, Tim; Häderer, Ines K; Lajeunesse, Marc J; Anthes, Nils

    2016-02-01

    Since Darwin's conception of sexual selection theory, scientists have struggled to identify the evolutionary forces underlying the pervasive differences between male and female behavior, morphology, and physiology. The Darwin-Bateman paradigm predicts that anisogamy imposes stronger sexual selection on males, which, in turn, drives the evolution of conventional sex roles in terms of female-biased parental care and male-biased sexual dimorphism. Although this paradigm forms the cornerstone of modern sexual selection theory, it still remains untested across the animal tree of life. This lack of evidence has promoted the rise of alternative hypotheses arguing that sex differences are entirely driven by environmental factors or chance. We demonstrate that, across the animal kingdom, sexual selection, as captured by standard Bateman metrics, is indeed stronger in males than in females and that it is evolutionarily tied to sex biases in parental care and sexual dimorphism. Our findings provide the first comprehensive evidence that Darwin's concept of conventional sex roles is accurate and refute recent criticism of sexual selection theory.

  11. Providing Radiation Protection Experts in the United Kingdom

    International Nuclear Information System (INIS)

    Partington, C.; Owen, D.

    2004-01-01

    The EEC Directive on Qualified Experts in Radiation Protection has been implemented in the United Kingdom by the Ionising Radiations Regulations 1999 (IRR99). These Regulations require Radiation Employers to appoint suitable Radiation Protection Advisers (RPA) who must be consulted in certain circumstances when starting work with, or using ionising radiations. Radiation Protection Advisers have to have a current certificate of competence and, to gain one of these, must have demonstrated their competence in one of two ways either by achieving a National Vocational Qualification in Radiation Protection Practice or by being Certificated by an Assessing Body. Assessing Bodies have to be recognised by the Health and Safety Executive, who undertake a rigorous assessment process to determine whether the proposed Assessing Body is fit to undertake RPA Assessments. By July 2003, only two such Assessing Bodies had been approved in the UK. These two Assessing Bodies are ? RPA 2000 a company established by the four leading Radiation Protection Professional Societies in the UK for assessing anyone in the UK as Radiation Protection Advisers, And ? BNFL established by BNFL to assess the competence of BNFL's own Radiation Protection Advisers. This paper will describe the standards against which Radiation Protection Advisers are assessed, the manner in which each of these two Assessing Bodies carry out the assessment process and their experience to date. The way in which Radiation Employers carry out the appointment process will also be described. Potential future developments of the Assessment Process and standards will also be discussed. (Author)

  12. Radioactivity and United Kingdom estuaries: an overview identifying research priorities

    International Nuclear Information System (INIS)

    Hamilton, E.I.; Clifton, R.J.; Stevens, H.E.

    1985-05-01

    The report consists of the results of an evaluation of research priorities for the environmental radioactivity of estuaries, (and near shore waters) of the United Kingdom. The format of this report is:(i) general conclusions for the future requirements for research in the field of environmental radioactivity; (ii) an overview of some specific recommendations for research; and (iii) an appendix in which a comprehensive evaluation of the research priorities for specific areas of research are given. On the basis that man is the prime target for concern and protection, special attention has been given to the environment in the vicinity of the British Nuclear Fuels (BNFL) reprocessing plant at Sellafield, Cumbria, which is the source of major releases of a variety of radionuclides into the natural environment. Subjects covered in the Appendix are: site factors; pathways to man; source term; hot particles; terrestrial inputs; surveys and monitoring; analysis; organics; field versus laboratory data; biology; bioaccumulation factors; some bioaccumulators of radioactivity; bioturbation; bacteria; genetics; natural change; sediment; resuspension; surfaces; Ksub(d) factors; pore liquids; diagenesis and the ageing processes; airborne transport of radionuclides; models; natural radioactivity; public opinion; recreation; the ICRP; the ALARA principle; decommissioning of nuclear power stations; identification of research requirements; environmental radioactivity - the national effort. (U.K.)

  13. Medical leadership and management in the United Kingdom.

    Science.gov (United States)

    Kyratsis, Yiannis; Armit, Kirsten; Zyada, Azra; Lees, Peter

    2016-06-01

    This article aims to outline the historical development of medical leadership in the United Kingdom (UK), present recent advances, and discuss professional development and future prospects. With increasing involvement of medical professionals in top managerial roles in the UK over the last 30 years, leadership development initiatives have been growing steadily and there is increasing recognition of the need for leadership and management skills for doctors. Such skills can help to greatly improve patient care as well as enhance organisational effectiveness and productivity. The central involvement of professional bodies such as the UK Faculty of Medical Leadership and Management, and the establishment of medical fellowship schemes, have provided a solid foundation for a new generation of aspiring medical leaders but there is still a long way to go to achieve a higher degree of professionalism for clinical leadership in the UK. The evidence base is weak such that integrated efforts by clinicians and management academics have much to offer in achieving the vision of socially responsible, clinically relevant and research informed medical leadership training. © The Royal Australian and New Zealand College of Psychiatrists 2016.

  14. Economic evaluation of human papillomavirus vaccination in the United Kingdom.

    Science.gov (United States)

    Jit, Mark; Choi, Yoon Hong; Edmunds, W John

    2008-07-17

    To assess the cost effectiveness of routine vaccination of 12 year old schoolgirls against human papillomavirus infection in the United Kingdom. Economic evaluation. UK. Population Schoolgirls aged 12 or older. Costs, quality adjusted life years (QALYs), and incremental cost effectiveness ratios for a range of vaccination options. Vaccinating 12 year old schoolgirls with a quadrivalent vaccine at 80% coverage is likely to be cost effective at a willingness to pay threshold of pound30,000 (euro37,700; $59,163) per QALY gained, if the average duration of protection from the vaccine is more than 10 years. Implementing a catch-up campaign of girls up to age 18 is likely to be cost effective. Vaccination of boys is unlikely to be cost effective. A bivalent vaccine with the same efficacy against human papillomavirus types 16 and 18 costing pound13- pound21 less per dose (depending on the duration of vaccine protection) may be as cost effective as the quadrivalent vaccine although less effective as it does not prevent anogenital warts. Routine vaccination of 12 year old schoolgirls combined with an initial catch-up campaign up to age 18 is likely to be cost effective in the UK. The results are robust to uncertainty in many parameters and processes. A key influential variable is the duration of vaccine protection.

  15. The renewable energies market in the United Kingdom

    International Nuclear Information System (INIS)

    2001-08-01

    Targets for renewable energies in the United Kingdom (U.K.) have been set at 10 per cent of the total electricity produced by 2010. Out of a total annual consumption of 364 000 GWh, renewable energies now provide 2.8 per cent of the electricity in the U.K. As a result, market growth over the next decade is expected to reach 250 per cent. Several specific new regulations have also been introduced to support these targets. U.K. electricity supply companies must now set percentages from renewable sources, and new fiscal measures penalizing fossil-fuel consumption while promoting renewables are included in these new regulations. Extra funding to support renewables research and development, pilot and demonstration projects, marketing and dissemination activities to increase renewables take-up in the country has been earmarked. Renewables application in the filed of transportation fuels has been identified. Duty cuts on biodiesel fuel were made following the recent Green Fuel Challenge consultation exercise. Once demonstration projects are proposed, additional duty cuts for other biofuels might be made. There should be considerable expansion of the U.K. renewables market. Biomass, for primary energy and transportation fuels, offshore wind, small-scale hydro and photovoltaics (PVs) are all sectors where opportunities exist. Fuel cell and wave/tidal technologies are likely to show some promise once they make it to the commercial/mass production phase. 35 refs., 4 tabs., 2 figs

  16. United Kingdom procedures in case of nuclear accidents

    International Nuclear Information System (INIS)

    Chalfont, L.

    1988-01-01

    From the United Kingdom experience, general principles for establishing emergency plans are drawn. Every country with nuclear plant should have such emergency arrangements capable of dealing with the largest scale that can be envisaged as a practical possibility. While the effects of accidents cannot be anticipated in detail these plans should form a good flexible basis for providing the resources, communications and procedures that are likely to be needed. They encompass the administrative infrastructure of the area surrounding the nuclear installation and involve co-ordination with the police, fire services and ambulance services, the local and county authorities, the authorities responsible for food, agriculture, fisheries and water, and the health authorities including hospitals and medical services. Special training and procedures have to be established for the personnel that are involved and exercises graduating from the exercising of special procedures to large scale simulated accidents need to be carried out periodically. Good communication systems have to be established between the nuclear installations, the operational support centres or equivalent, the field and headquarters units of the relevant organizations, and the central government departments so that whatever additional resources and support are needed can be marshalled quickly and efficiently. (author)

  17. Flavonoids and Melanins: a common strategy across two kingdoms.

    Science.gov (United States)

    Carletti, Giorgia; Nervo, Giuseppe; Cattivelli, Luigi

    2014-01-01

    Ultraviolet (UV) radiations alter a number of metabolic functions in vivant. They produce damages to lipids, nucleic acids and proteins, generating reactive oxygen species such as singlet oxygen (O2), hydroxyl radical (HO) and superoxide anion (O2 (-)). Plants and animals, after their water emersion, have developed biochemical mechanisms to protect themselves from that environmental threat through a common strategy. Melanins in animals and flavonoids in plants are antioxidant pigments acting as free radical scavenging mechanisms. Both are phenol compounds constitutively synthesized and enhanced after exposure to UV rays, often conferring a red-brown-dark tissue pigmentation. Noteworthy, beside anti-oxidant scavenging activity, melanins and flavonoids have acquired secondary functions that, both in plants and animals, concern reproductions and fitness. Plants highly pigmented are more resistant to biotic and abiotic stresses. Darker wild vertebrates are generally more aggressive, sexually active and resistant to stress than lighter individuals. Flavonoids have been associated with signal attraction between flowers and insects and with plant-plant interaction. Melanin pigmentation has been proposed as trait in bird communication, acting as honest signals of quality. This review shows how the molecular mechanisms leading to tissue pigmentation have many functional analogies between plants and animals and how their origin lies in simpler organisms such as Cyanobacteria. Comparative studies between plant and animal kingdoms can reveal new insight of the antioxidant strategies in vivant.

  18. The benefit of seat belt legislation in the United Kingdom.

    Science.gov (United States)

    McCarthy, M

    1989-09-01

    Legislation for compulsory wearing of seat belts by car drivers and front seat passengers has been acclaimed as a major public health advance. Reports from other countries, and two recent evaluative studies in the United Kingdom, have suggested that legislation reduces both deaths and injuries. To assess the effect of the UK law 5 years after its implementation, trends in routine data for 1976-1987 have been reviewed. There were two sources of data: mortality statistics, published by the Office of Population Censuses and Surveys in the quarterly Monitor DH4, and road accident statistics, recorded by the police and published by the Department of Transport. There is a downward trend in deaths over the period, but the data show little impact from the law. One explanation for this lack of effect is the risk compensation hypothesis, which suggests that "safety" improvements are transferred by drivers into increased performance--the amount and speed of travel. Public health policies need to take into account the complex behavioural interactions between travel and safety choices if they are to affect underlying trends.

  19. Civil gymnastics associations and sports in the Kingdom of Serbia

    Directory of Open Access Journals (Sweden)

    Vukašinović Vladan

    2016-01-01

    Full Text Available The aim of this study was to enable insight and systemization of data relevant for the appearance of sports in the Kingdom of Serbia through reviews of adequate monographs and series of publications. Primary assumption was founded on the expectation to determine a direct link between gymnastics and the falcon system of exercising with sports that was rising. The historic method has been used for the research. Work results indicate a significant role of civil gymnastics associations - falcons (the falcon and knight (Dusan the Mighty as a phenomenon in popularization and development of modern sports at the end of the 19th and the beginning of the 20th century in Serbia. All these associations, no matter what their name was, had intentions to maintain their existing and attract new membership, and they foresaw with their rules and statutes acceptance and the introduction of other sports activities and forming of clubs, apart from gymnastics which was the skeleton of exercising curriculum. Newly founded gymnastics - sports departments in fighting, marksmanship, skating, riding, swimming, rowing, velocipede, football developed and grew into sports clubs. Their separation from core gymnastics associations enabled faster development of individual sports branches, which stood for the first modern sports in Serbia.

  20. Paleomagnetic investigations at Mahd adh Dhahab, Kingdom of Saudi Arabia

    Science.gov (United States)

    Gettings, M.E.

    1985-01-01

    Paleomagnetic studies of 25 oriented bedrock specimens from Jabal Mahd adh Dhahab, located 160 km southeast of Al Madinah, Kingdom of Saudi Arabia, have yielded important structural information relating to the geologic history of this base and precious metal deposit. Samples were collected along one traverse away from the mineralized zones, across the northeast-plunging antiform that constitutes the dominant regional structure of the area, and along another traverse down the axis of the mineralized zones. Lithologies range from andesite flows through andesitic to rhyodacitic tuffs, lapilli tuffs, and volcaniclastic sediments. Measurements of remanent magnetization direction and intensity before and after stepwise alternating-field demagnetization ranging from 25 Oersted (Oe) to 1000 Oe were carried out on all samples. Three classes of demagnetization behavior were observed: A very stable class with little change in direction and intensity of magnetization; a class in which rapid changes were observed at first but which then settled on a high coercivity stable component of magnetization; and a class in which the magnetization was composed of a spectrum of low coervicity components, and continuous variation of direction and intensity of magnetization occurred.

  1. United Kingdom national paediatric bilateral cochlear implant audit: preliminary results.

    Science.gov (United States)

    Cullington, Helen; Bele, Devyanee; Brinton, Julie; Lutman, Mark

    2013-11-01

    Prior to 2009, United Kingdom (UK) public funding was mainly only available for children to receive unilateral cochlear implants. In 2009, the National Institute for Health and Care Excellence published guidance for cochlear implantation following their review. According to these guidelines, all suitable children are eligible to have simultaneous bilateral cochlear implants or a sequential bilateral cochlear implant if they had received the first before the guidelines were published. Fifteen UK cochlear implant centres formed a consortium to carry out a multi-centre audit. The audit involves collecting data from simultaneously and sequentially implanted children at four intervals: before bilateral cochlear implants or before the sequential implant, 1, 2, and 3 years after bilateral implants. The measures include localization, speech recognition in quiet and background noise, speech production, listening, vocabulary, parental perception, quality of life, and surgical data including complications. The audit has now passed the 2-year point, and data have been received on 850 children. This article provides a first view of some data received up until March 2012.

  2. Bacterial flagella: twist and stick, or dodge across the kingdoms.

    Directory of Open Access Journals (Sweden)

    Yannick Rossez

    2015-01-01

    Full Text Available The flagellum organelle is an intricate multiprotein assembly best known for its rotational propulsion of bacteria. However, recent studies have expanded our knowledge of other functions in pathogenic contexts, particularly adherence and immune modulation, e.g., for Salmonella enterica, Campylobacter jejuni, Pseudomonas aeruginosa, and Escherichia coli. Flagella-mediated adherence is important in host colonisation for several plant and animal pathogens, but the specific interactions that promote flagella binding to such diverse host tissues has remained elusive. Recent work has shown that the organelles act like probes that find favourable surface topologies to initiate binding. An emerging theme is that more general properties, such as ionic charge of repetitive binding epitopes and rotational force, allow interactions with plasma membrane components. At the same time, flagellin monomers are important inducers of plant and animal innate immunity: variation in their recognition impacts the course and outcome of infections in hosts from both kingdoms. Bacteria have evolved different strategies to evade or even promote this specific recognition, with some important differences shown for phytopathogens. These studies have provided a wider appreciation of the functions of bacterial flagella in the context of both plant and animal reservoirs.

  3. Assessment methods in surgical training in the United Kingdom

    Directory of Open Access Journals (Sweden)

    Evgenios Evgeniou

    2013-02-01

    Full Text Available A career in surgery in the United Kingdom demands a commitment to a long journey of assessment. The assessment methods used must ensure that the appropriate candidates are selected into a programme of study or a job and must guarantee public safety by regulating the progression of surgical trainees and the certification of trained surgeons. This review attempts to analyse the psychometric properties of various assessment methods used in the selection of candidates to medical school, job selection, progression in training, and certification. Validity is an indicator of how well an assessment measures what it is designed to measure. Reliability informs us whether a test is consistent in its outcome by measuring the reproducibility and discriminating ability of the test. In the long journey of assessment in surgical training, the same assessment formats are frequently being used for selection into a programme of study, job selection, progression, and certification. Although similar assessment methods are being used for different purposes in surgical training, the psychometric properties of these assessment methods have not been examined separately for each purpose. Because of the significance of these assessments for trainees and patients, their reliability and validity should be examined thoroughly in every context where the assessment method is being used.

  4. Exploring support for shale gas extraction in the United Kingdom

    International Nuclear Information System (INIS)

    Andersson-Hudson, Jessica; Knight, William; Humphrey, Mathew; O’Hara, Sarah

    2016-01-01

    The development of shale gas in the United Kingdom (UK) using hydraulic fracturing, more commonly known as ‘fracking’, remains in its infancy. Yet understanding public attitudes for this fledgling industry is important for future policy considerations, decision-making and for industry stakeholders. This study uses data collected from the University of Nottingham, UK nationwide online survey (n=3823) conducted in September 2014, to consider ten hypothesises about the UK public's attitudes towards shale gas. From the survey data we can see that 43.11% of respondents support shale gas extraction in the UK. Furthermore, our results show that women, class DE respondents, non-Conservative party supporters, and respondents who positively associate shale gas with water contamination or earthquakes are less likely to support the extraction of shale gas in the UK. We also discuss potential policy implications for the UK government arising from these findings. - Highlights: • September 2014 survey of British attitudes towards allowing shale gas extraction. • Over 75% or respondents correctly identify shale gas. • 43.11% of respondents support shale gas extraction in the UK.

  5. Emergency plans for civil nuclear installations in the United Kingdom

    International Nuclear Information System (INIS)

    Gronow, W.S.

    1984-01-01

    The operators of nuclear installations in the United Kingdom have plans to deal with accidents or emergencies at their nuclear sites. These plans provide for any necessary action, both on and off the nuclear site, to protect members of the public and are regularly exercised. The off-site actions involve the emergency services and other authorities which may be called upon to implement measures to protect the public in any civil emergency. In a recent review of these plans by Government Departments and agencies and the nuclear site operators, a number of possible improvements were identified. These improvements are concerned mainly with the provisions made for liaison with local and national authorities and for public information and have been incorporated into existing plans. An outline is given of the most likely consequences of an accidental release of radioactive material and the scope of emergency plans. Details are also provided on the responsibilities and functions of the operator and other organizations with duties under the plans and the arrangements made for public information. (author)

  6. Internal fire protection analysis for the United Kingdom EPR design

    Energy Technology Data Exchange (ETDEWEB)

    Laid, Abdallah [Nuclear New Build Generation Company Ltd. (NNB GenCo), Barnwood (United Kingdom). EDF Energy Plc.; Cesbron, Mickael [Service Etudes et Project Thermiques et Nucleaires (SEPTEN), Lyon (France). EDF-SA

    2015-12-15

    In the deterministic design basis analysis of the United Kingdom (UK) EPR based nuclear power plants all postulated initiating events are grouped into two different types, internal faults and internal/external hazards. ''Internal Fires'' is one of the internal hazards analysed at the design stage of the UK EPR. In effect, the main safety objective for fire protection is to ensure that all the required safety functions are performed in the event of an internal fire. To achieve this safety objective, provisions for protection against fire risks are taken to: (i) limit the spread of a fire, protect the safety functions of the facility; (ii) limit the propagation of smoke and dispersion of toxic, radioactive, inflammable, corrosive or explosive materials, and (iii) ensure the achievement of a safe shutdown state, personnel evacuation and all other necessary emergency actions. This paper presents the UK EPR approach on how the above provisions are applied. Such provisions involve implementing means of fire prevention, surveillance, firefighting and limiting fire consequences, appropriate to the risks inherent to the facility. Overall, the design of the UK EPR fire protection systems is based on three types of measures: prevention, containment and control.

  7. SOFTWARE FOR SUPERCOMPUTER SKIF “ProLit-lC” and “ProNRS-lC” FOR FOUNDRY AND METALLURGICAL PRODUCTIONS

    Directory of Open Access Journals (Sweden)

    A. N. Chichko

    2008-01-01

    Full Text Available The data of modeling on supercomputer system SKIF of technological process of  molds filling by means of computer system 'ProLIT-lc', and also data of modeling of the steel pouring process by means ofTroNRS-lc'are presented. The influence of number of  processors of  multinuclear computer system SKIF on acceleration and time of  modeling of technological processes, connected with production of castings and slugs, is shown.

  8. Conservation Station and Beyond: Experiences at Disney's Animal Kingdom That Make a Difference.

    Science.gov (United States)

    Ogden, Jackie; Lehnhardt, Kathy; Mellen, Jill; Dierking, Lynn; Adelman, Leslie; Burks, Kyle; Miller, Lance

    2001-01-01

    Describes a five-year plan for educational research and evaluation at the Disney Animal Kingdom. Focuses on conservation-related issues and presents some of the preliminary results from the study of visitor attitudes. (DDR)

  9. Anti-Terrorism Authority Under the Laws of the United Kingdom and the United States

    National Research Council Canada - National Science Library

    Feikert, Clare; Doyle, Charles

    2006-01-01

    This is a comparison of the laws of the United Kingdom and of the United States that govern criminal and intelligence investigations of terrorist activities Both systems rely upon a series of statutory authorizations...

  10. A review of the disposal of miscellaneous radioactive wastes in the United Kingdom

    International Nuclear Information System (INIS)

    Hookway, B.

    1980-01-01

    Current practices in the United Kingdom for waste disposal from ''minor users'' of radioactive materials are reviewed. The regulation of the disposal of solid, liquid and airborne wastes is discussed. (H.K.)

  11. The Privatization of Public Enterprises in the United Kingdom, 1979–1987

    NARCIS (Netherlands)

    Auger, J.F.

    2010-01-01

    How do states have privatized public enterprises? In the book The Official History of Privatization, David Parker, a notorious economist of regulation and privatization, shed light on a country at the forefront of economic reforms, the United Kingdom.

  12. Questioning the Location of the Old Kingdom Capital of Memphis, Egypt

    Directory of Open Access Journals (Sweden)

    Serena Love

    2003-11-01

    Full Text Available The capital city of Memphis was ancient Egypt’s oldest and largest city. However, the city’s origin is shrouded in myth. This study challenges five different references to Memphis, from both classical and historical accounts and concludes that Memphis’ boundary should be redefined. These accounts are reviewed to illustrate the confusion amongst early historians and travellers as to the precise location of Memphis and to highlight the association between the capital and the pyramids of the Giza Plateau. For the Old Kingdom, the urban limits of Memphis should not be restricted to the modern mound of Mit Rahina, but rather the boundaries should be expanded to parallel the Old Kingdom pyramids. Recent archaeological investigations, employing sub-surface sampling techniques, have revealed contemporary Old Kingdom occupational debris scattered throughout the entire Memphite region. The inclusion of archaeological material, in combination with the historical records, will create a different interpretation for Egypt’s Old Kingdom capital city.

  13. Properties of hot rolled steels for enamelling

    International Nuclear Information System (INIS)

    Gavrilovski, Dragica; Gavrilovski, Milorad

    2003-01-01

    The results of an investigation of the structure and properties of experimental produced hot rolled steels suitable for enamelling are presented in the paper. Hot rolled steels for enamelling represent a special group of the steels for conventional enamelling. Their quality has to be adapted to the method and conditions of enamelling. Therefore, these steels should meet some specific requirements. In addition to usual investigation of the chemical composition and mechanical properties, microstructure and quality of the steel surface also were investigated. The basic aim was to examine steels capability for enamelling, i. e. steels resistance to the fish scales phenomena, by trial enamelling, as well as quality of the steel - enamel contact surface, to evaluate the binding. Also, the changes of the mechanical properties, especially the yield point, during thermal treatment, as a very specific requirement, were investigated, by simplified method. Good results were obtained confirming the steels capability for enamelling. (Original)

  14. United Kingdom health research analyses and the benefits of shared data.

    Science.gov (United States)

    Carter, James G; Sherbon, Beverley J; Viney, Ian S

    2016-06-24

    To allow research organisations to co-ordinate activity to the benefit of national and international funding strategies requires assessment of the funding landscape; this, in turn, relies on a consistent approach for comparing expenditure on research. Here, we discuss the impact and benefits of the United Kingdom's Health Research Classification System (HRCS) in national landscaping analysis of health research and the pros and cons of performing large-scale funding analyses. The first United Kingdom health research analysis (2004/2005) brought together the 11 largest public and charity funders of health research to develop the HRCS and use this categorisation to examine United Kingdom health research. The analysis was revisited in 2009/2010 and again in 2014. The most recent quinquennial analysis in 2014 compiled data from 64 United Kingdom research organisations, accounting for 91% of all public/charitable health research funding in the United Kingdom. The three analyses summarise the United Kingdom's health research expenditure in 2004/2005, 2009/2010 and 2014, and can be used to identify changes in research activity and disease focus over this 10 year period. The 2004/2005 analysis provided a baseline for future reporting and evidence for a United Kingdom Government review that recommended the co-ordination of United Kingdom health research should be strengthened to accelerate the translation of basic research into clinical and economic benefits. Through the second and third analyses, we observed strategic prioritisation of certain health research activities and disease areas, with a strong trend toward increased funding for more translational research, and increases in specific areas such as research on prevention. The use of HRCS in the United Kingdom to analyse the research landscape has provided benefit both to individual participatory funders and in coordinating initiatives at a national level. A modest amount of data for each project is sufficient for a

  15. Psychiatry training in the United Kingdom--part 2: the training process.

    Science.gov (United States)

    Christodoulou, N; Kasiakogia, K

    2015-01-01

    In the second part of this diptych, we shall deal with psychiatric training in the United Kingdom in detail, and we will compare it--wherever this is meaningful--with the equivalent system in Greece. As explained in the first part of the paper, due to the recently increased emigration of Greek psychiatrists and psychiatric trainees, and the fact that the United Kingdom is a popular destination, it has become necessary to inform those aspiring to train in the United Kingdom of the system and the circumstances they should expect to encounter. This paper principally describes the structure of the United Kingdom's psychiatric training system, including the different stages trainees progress through and their respective requirements and processes. Specifically, specialty and subspecialty options are described and explained, special paths in training are analysed, and the notions of "special interest day" and the optional "Out of programme experience" schemes are explained. Furthermore, detailed information is offered on the pivotal points of each of the stages of the training process, with special care to explain the important differences and similarities between the systems in Greece and the United Kingdom. Special attention is given to The Royal College of Psychiatrists' Membership Exams (MRCPsych) because they are the only exams towards completing specialisation in Psychiatry in the United Kingdom. Also, the educational culture of progressing according to a set curriculum, of utilising diverse means of professional development, of empowering the trainees' autonomy by allowing initiative-based development and of applying peer supervision as a tool for professional development is stressed. We conclude that psychiatric training in the United Kingdom differs substantially to that of Greece in both structure and process. Τhere are various differences such as pure psychiatric training in the United Kingdom versus neurological and medical modules in Greece, in

  16. Thai students and their reasons for choosing to study in United Kingdom universities

    OpenAIRE

    Tarry, Estelle F

    2008-01-01

    This thesis seeks to consider Thai students and their reasons for choosing to study in United Kingdom universities. Through the literature review it has been identified that higher education is globally expanding. Competing knowledgebased economies with higher education institutions have led education to be considered a market commodity and consequently the marketization of higher education in competitive world markets. This is exemplified by discussion of the United Kingdom higher education ...

  17. A qualitative study of work-life balance amongst specialist orthodontists in the United Kingdom

    OpenAIRE

    Cunningham, S. J.; Bateman, L. E.; Collins, J. M.

    2016-01-01

    Objective: To identify factors affecting work-life balance amongst male and female orthodontists in the United Kingdom. Design: A qualitative interview-based study with a cross-sectional design. Subjects: Specialist orthodontists working in specialist practice and the hospital service in the United Kingdom were selected by purposive sampling. Methods: In-depth semi-structured interviews were conducted with eighteen orthodontic specialists. Interview transcripts were analysed using Framework A...

  18. Alcohol consumption among university students in Ireland and the United Kingdom from 2002 to 2014

    DEFF Research Database (Denmark)

    Davoren, M.P.; Demant, Jakob Johan; Shiely, Frances

    2016-01-01

    Alcohol is a leading cause of global suffering. Europe reports the uppermost volume of alcohol consumption in the world, with Ireland and the United Kingdom reporting the highest levels of binge drinking and drunkenness. Levels of consumption are elevated among university students. Thus......, this literature review aims to summarise the current research on alcohol consumption among university students in the Republic of Ireland and the United Kingdom....

  19. High temperature oxidation behavior of ODS steels

    Science.gov (United States)

    Kaito, T.; Narita, T.; Ukai, S.; Matsuda, Y.

    2004-08-01

    Oxide dispersion strengthened (ODS) steels are being developing for application as advanced fast reactor cladding and fusion blanket materials, in order to allow increased operation temperature. Oxidation testing of ODS steel was conducted under a controlled dry air atmosphere to evaluate the high temperature oxidation behavior. This showed that 9Cr-ODS martensitic steels and 12Cr-ODS ferritic steels have superior high temperature oxidation resistance compared to 11 mass% Cr PNC-FMS and 17 mass% Cr ferritic stainless steel. This high temperature resistance is attributed to earlier formation of the protective α-Cr 2O 3 on the outer surface of ODS steels.

  20. Review on Cold-Formed Steel Connections

    Science.gov (United States)

    Tan, Cher Siang; Mohammad, Shahrin; Md Tahir, Mahmood; Shek, Poi Ngian

    2014-01-01

    The concept of cold-formed light steel framing construction has been widespread after understanding its structural characteristics with massive research works over the years. Connection serves as one of the important elements for light steel framing in order to achieve its structural stability. Compared to hot-rolled steel sections, cold-formed steel connections perform dissimilarity due to the thin-walled behaviour. This paper aims to review current researches on cold-formed steel connections, particularly for screw connections, storage rack connections, welded connections, and bolted connections. The performance of these connections in the design of cold-formed steel structures is discussed. PMID:24688448

  1. The SEEC United Kingdom energy demand forecast (1993-2000)

    Energy Technology Data Exchange (ETDEWEB)

    Fouquet, R; Hawdon, D; Pearson, P; Robinson, C; Stevens, P

    1993-12-16

    The aims of this paper are to present the underlying determinants of fuel consumption, such as economic activity and prices, develop a series of simple yet reliable sectoral models of energy demand, which incorporate recent modelling developments; provide forecasts of energy demand and its environmental consequences; examine the effects of VAT on domestic fuel and increased competition in the electricity sector; and aid the present debate on energy markets. The paper analyses world oil prices, with a particular focus on Iraq's role, reviews energy policy in the UK and discusses SEEC's expectations about UK fuel prices in coming years and how they vary among sectors. It forecasts final user demand in the domestic, iron and steel, other industry, transport, agricultural, public administration and defence and miscellaneous sectors. The paper also examines the major changes that are underway in electricity generators' demand for fuel, and primary energy consumption and its environmental implications.

  2. Wisdom’s rebellion: Kingdom politics as a guerrilla drama

    Directory of Open Access Journals (Sweden)

    Petrus P. Kruger

    2015-06-01

    Full Text Available This article aims at exploring kingdom politics in South Africa as a guerrilla drama, not only of a contemporary play of wisdom as human virtue, but specifically in the form of the personified Wisdom’s play (cf. Christ’s parable of the children on the marketplace; Lk 7. Firstly, it investigates the availability of hermeneutical space for such an enterprise, attending to the concept of rebellion vis-à-vis a scripture-based, imaginative, theodramatic articulation of the Wisdom’s play of the parable. Secondly, the public space for the enactment of such a ‘wisdom’s rebellion’ is probed. It should not be neutrally indifferent to, but positively advancing of, the nearly universally accepted ‘golden rule’. The public space should, in the public imagination, be seen and treated as a kind of public theatre, hospitable to a plurality of worldviews, each freely and imaginatively enacting its own political alternatives before the critical eyes of a democratic voting public. A follow-up article will attempt to outline the difference it might make to the human dignity of the participants (actors and in their humane political actions (theodramatic roles, if they can imagine themselves as performing (not only theorising about and not only feeling passionately about wisdom’s subversive play of God’s kingdom in South Africa.   Hierdie artikel stel ondersoek in na koninkrykspolitiek in Suid-Afrika as ’n guerrilladrama wat die vorm van ’n wysheidspel aanneem; nie alleen ’n eietydse spel van wysheid as ’n menslike deug nie, maar veral as spel van die gepersonifieerde Wysheid (vgl. Christus se gelykenis van die kinders wat op die markplein speel; Luk 7. Eerstens word na die beskikbaarheid van ’n hermeneutiese ruimte vir so ’n onderneming gevra. Daarby word aandag geskenk aan die konsep van rebellie in verband met ’n skriftuurlik gefundeerde, verbeeldingryke, teodramatiese uitwerking van Wysheid se spel na aanleiding van die

  3. Urban air quality of kathmandu valley "Kingdom of Nepal"

    Science.gov (United States)

    Sharma, C. K.

    The oval shaped tectonic basin of Kathmandu valley, occupying about 656 sq.km is situated in the middle sector of Himalayan range. There are three districts in the valley, i.e. Kathmandu, Lalitpur and Bhaktapur. Out of the three, the most populated is Kathmandu city (the capital of Kingdom of Nepal) which has a population of 668,00 in an area of approximately 50 km 2. The energy consumption of the city population is about 1/3 of the total import to Nepal of gasoline, diesel, kerosene, furnace oil and cooking gas. This has resulted heavy pollution of air in the city leading to bronchitis, and throat and chest diseases. Vehicles have increased several fold in recent months and there are 100,000 in number on the road and they have 900 km of road, out of which only 25% is metalled. Most of the two and three wheelers are polluting the air by emission of gases as well as dust particulate. SO 2 has been found to go as high as 202 μg cm -3 and NO 2 to 126 μg cm -3 particularly in winter months when a thick layer of fog covers the valley up to 10 am in the morning. All the gases are mixed within the limited air below the fog and the ground. This creates the problem. Furthermore, municipal waste of 500 m 3 a day and also liquid waste dumped directly into the Bagmati river at the rate of 500,000 ℓ d -1 makes the city ugly and filthy. Unless pollution of air, water and lard are controlled in time, Nepal will lose much of its foreign exchange earnings from the tourist industry. It is found that tourist arrivals have considerably reduced in recent years and most of hotels occupancy is 50-60% in peak time. Nepal is trying to introduce a legal framework for pollution control but it will take time to become effective.

  4. Early Jurassic allotherians from South Wales (United Kingdom

    Directory of Open Access Journals (Sweden)

    W. A. Clemens

    2007-02-01

    Full Text Available Fossils from two fissure fillings in Pant Quarry (designated Pant 4 and Pant 5, South Wales, United Kingdom, probably of Early Jurassic age document a taxonomically diverse vertebrate fauna, the Morganucodon-sphenodont fauna, composed of several kinds of reptiles, non-mammalian synapsids, and mammals. Six isolated molariform teeth from Pant 4 and 5 fissures clearly record the presence of Thomasia (Mammalia, Allotheria, Haramiyidae, a genus previously known only from purported Late Triassic faunas of southwestern England, France, Belgium, Luxemburg, Germany, and Switzerland. Small morphological differences from teeth in the larger English and continental European samples warrant identification of the Welsh material as Thomasia cf. moorei. The highly derived morphology of an isolated molariform tooth from Pant 5 fissure indicates the presence of another, possibly allotherian, taxon. Fossilien aus zwei wahrscheinlich unterjurassischen Spaltenfüllungen (Pant 4 und Pant 5 im Steinbruch Pant in Süd-Wales dokumentieren eine taxonomisch diverse Wirbeltierfauna. Diese Morganucodon-Sphenodontiden-Fauna besteht aus verschiedenen Formen von Reptilien, Synapsiden und Säugetieren. Sechs isolierte molariforme Zähne aus den Spaltenfüllungen Pant 4 und Pant 5 belegen eindeutig das Vorkommen von Thomasia (Mammalia, Allotheria, Haramiyidae, einer bisher nur aus vermutlich obertriassischen Faunen Südwest-Englands, Frankreichs, Belgiens, Luxemburgs, Deutschlands und der Schweiz bekannten Gattung. Geringe morphologische Unterschiede zu dem umfangreicheren Material aus England und Kontinental-Europa sprechen für die Identifikation des neuen Materials als Thomasia cf. moorei. Die stark abgeleitete Morphologie eines isolierten molariformen Zahnes aus der Spalte Pant 5 belegt das Vorkommen eines anderen Taxons, das möglicherweise auch den Allotheria zuzuordnen ist. doi:10.1002/mmng.200600018

  5. NPL support for environmental radioactivity measurements in the United Kingdom

    International Nuclear Information System (INIS)

    Jerome, Simon

    2009-01-01

    Full text: The United Kingdom was one of the first nations to initiate a civil nuclear power programme in the 1950s, with the first commercial generation of electricity being achieved in 1957. As the civil nuclear programme grew in size, an ongoing programme of environmental monitoring was instituted by central government that placed the responsibility for monitoring radioactivity in the local environment and the measurement of discharges of radioactive gases and liquids with the site operator, the Environment Agency, the Environment and Heritage Service, the Food Standards Agency and the Scottish Environment Protection Agency (or their predecessors). This presentation will discuss the sources of radioactivity in the UK environment from the nuclear industry, natural and other sources, focussing on how these sources of radioactivity are monitored and what future trends may be, taking the Windscale fire of 1957, the Chernobyl accident and the Litvinenko incident of 2006 as examples of how unexpected events have been addressed in the UK. As the national metrology institute for the UK, the NPL is required to provide support to the National Measurement System infrastructure of the UK, including the measurement of radioactivity. The presentation will also describe the absolute standardisation of radioactivity at the NPL, and how this is disseminated to organisations measuring environmental radioactivity in the UK by means of directly traceable standards of radioactivity and through the provision of an ongoing series of proficiency test exercises. The outcomes of some recent proficiency tests will be discussed, with emphasis on how the general performance of laboratories participating in these proficiency tests has matured over the years since their inception in 1989. In addition, the data treatment of such proficiency tests will also be examined in order to illustrate that statutory regulatory bodies, laboratory accreditation organisations and customers are able to

  6. Notch aspects of RSP steel microstructure

    Directory of Open Access Journals (Sweden)

    Michal Černý

    2012-01-01

    Full Text Available For a rather long time, basic research projects have been focused on examinations of mechanical properties for Rapid Solidification Powder (RSP steels. These state-of-art steels are commonly known as “powdered steels“. In fact, they combine distinctive attributes of conventional steel alloys with unusual resistance of construction material manufactured by so called “pseudo-powdered” metallurgy.Choice of suitable materials for experimental verification was carried out based on characteristic application of so called “modern steel”. First, groups of stainless and tool steel types (steel grades ČSN 17 and 19 were selected. These provided representative specimens for the actual comparison experiment. For stainless steel type, two steel types were chosen: hardenable X47Cr14 (ČSN 17 029 stainless steel and non-hardenable X2CrNiMo18-14-3 (ČSN 17 350 steel. They are suitable e.g. for surgical tools and replacements (respectively. For tooling materials, C80U (ČSN 19 152 carbon steel and American D2 highly-alloyed steel (ČSN “equivalent” being 19 572 steel were chosen for the project. Finally, the M390 Böhler steel was chosen as representative of powdered (atomized steels. The goal of this paper is to discuss structural aspects of modern stainless and tool steel types and to compare them against the steel made by the RSP method. Based on the paper's results, impact of powdered steel structural characteristics on the resistance to crack initiation shall be evaluated.

  7. Anodized Steel Electrodes for Supercapacitors.

    Science.gov (United States)

    Sagu, Jagdeep S; Wijayantha, K G Upul; Bohm, Mallika; Bohm, Siva; Kumar Rout, Tapan

    2016-03-09

    Steel was anodized in 10 M NaOH to enhance its surface texture and internal surface area for application as an electrode in supercapacitors. A mechanism was proposed for the anodization process. Field-emission gun scanning electron microscopy (FEGSEM) studies of anodized steel revealed that it contains a highly porous sponge like structure ideal for supercapacitor electrodes. X-ray photoelectron spectroscopy (XPS) measurements showed that the surface of the anodized steel was Fe2O3, whereas X-ray diffraction (XRD) measurements indicated that the bulk remained as metallic Fe. The supercapacitor performance of the anodized steel was tested in 1 M NaOH and a capacitance of 18 mF cm(-2) was obtained. Cyclic voltammetry measurements showed that there was a large psueudocapacitive contribution which was due to oxidation of Fe to Fe(OH)2 and then further oxidation to FeOOH, and the respective reduction of these species back to metallic Fe. These redox processes were found to be remarkably reversible as the electrode showed no loss in capacitance after 10000 cycles. The results demonstrate that anodization of steel is a suitable method to produce high-surface-area electrodes for supercapacitors with excellent cycling lifetime.

  8. Corrosion of steel in concrete

    International Nuclear Information System (INIS)

    Preece, C.M.

    1982-10-01

    A comparative study has been made of those properties of Massiv and Standard cements which are considered to determine their ability to protect steel reinforcement from corroding. Saturated Massiv cement has a higher evaporabel water content, but a significantly finer pore structure than has saturated Standard cement. This fine structure resulted in an electrical resistivity ten times higher and chloride diffusivity ten times lower than those of Standard cement. Electrochemical measurements have shown that the passive current density of steel in Massiv mortar is higher than that of steel in Standard mortar, but the higher current should lead to a more rapid decrease in potential to a level at which neither chloride attack of hydrogen evolution will occur. Whereas steel in Standard mortar was found to be highly susceptible to crevice corrosion, no such attack has been observed in Massiv mortar. Moreover, the initiation of chloride induced corrosion and the subsequent rates of corrosion were both lower in Massiv mortar than in Standard mortar. Thus, it may be predicted that Massiv cement would provide greater protection for steel reinforcement in underground structures exposed to chloride containing ground water than would Standard cement. (author)

  9. Protocol Additional to the Agreement between the Republic of Austria, the Kingdom of Belgium, the Kingdom of Denmark, the Republic of Finland, the Federal Republic of Germany, the Hellenic Republic, Ireland, the Italian Republic, the Grand Duchy of Luxembourg, the Kingdom of The Netherlands, the Portuguese Republic, the Kingdom of Spain, the Kingdom of Sweden, the European Atomic Energy Community and the International Atomic Energy Agency in implementation of Article III, (1) and (4) of the Treaty on the Non-Proliferation of Nuclear Weapons. Accession of the Czech Republic

    International Nuclear Information System (INIS)

    2010-01-01

    Protocol Additional to the Agreement between the Republic of Austria, the Kingdom of Belgium, the Kingdom of Denmark, the Republic of Finland, the Federal Republic of Germany, the Hellenic Republic, Ireland, the Italian Republic, the Grand Duchy of Luxembourg, the Kingdom of The Netherlands, the Portuguese Republic, the Kingdom of Spain, the Kingdom of Sweden, the European Atomic Energy Community and the International Atomic Energy Agency in implementation of Article III, (1) and (4) of the Treaty on the Non-Proliferation of Nuclear Weapons. Accession of the Czech Republic [es

  10. Ductility of high chromium stainless steels

    International Nuclear Information System (INIS)

    Peretyat'ko, V.N.; Kazantsev, A.A.

    1997-01-01

    Aimed to optimize the hot working conditions for high chromium stainless steels the experiments were carried in the temperature range of 800-1300 deg C using hot torsion tests and cylindrical specimens of ferritic and ferritic-martensitic steels 08Kh13, 12Kh13, 20Kh13, 30Kh13 and 40Kh13. Testing results showed that steel plasticity varies in a wide range depending on carbon content. Steels of lesser carbon concentration (08Kh13 and 12Kh13) exhibit a sharp increase in plasticity with a temperature rise, especially in the interval of 1200-1250 deg C. Steels 20Kh13 and 30Kh13 display insignificant plasticity increasing, whereas plastic properties of steel 40Kh13 increase noticeably in the range of 1000-1300 deg C. It is shown that optimal hot working conditions for specific steel must be selected with account of steel phase composition at high temperatures

  11. Financial Management: Emergency Steel Loan Guarantee Program

    National Research Council Canada - National Science Library

    2001-01-01

    In a February 1, 2001 letter, you expressed concerns about repayments of federally guaranteed loans by borrowers under the Emergency Steel Loan Guarantee Program and the effect of the program on the U.S. steel industry...

  12. Optimum design of steel structures

    CERN Document Server

    Farkas, József

    2013-01-01

    This book helps designers and manufacturers to select and develop the most suitable and competitive steel structures, which are safe, fit for production and economic. An optimum design system is used to find the best characteristics of structural models, which guarantee the fulfilment of design and fabrication requirements and minimize the cost function. Realistic numerical models are used as main components of industrial steel structures. Chapter 1 containts some experiences with the optimum design of steel structures Chapter 2 treats some newer mathematical optimization methods. Chapter 3 gives formulae for fabrication times and costs. Chapters 4 deals with beams and columns. Summarizes the Eurocode rules for design. Chapter 5 deals with the design of tubular trusses. Chapter 6 gives the design of frame structures and fire-resistant design rules for a frame. In Chapters 7 some minimum cost design problems of stiffened and cellular plates and shells are worked out for cases of different stiffenings and loads...

  13. Functionally Graded Mo sintered steels

    Directory of Open Access Journals (Sweden)

    Manuel Cisneros-Belmonte

    2016-12-01

    Full Text Available Functionally graded materials (FGM, the multi-materials, strive to satisfy the numerous requirements demanded of parts in a given combination of compositions and microstructures. The required material compatibility lead the manufacturing process and the achieving of an interface, not always diffuse. Powder metallurgy is one of the techniques used in manufacturing functionally graded materials, in particular the compaction matrix of the possible techniques for forming these materials. In this paper, a process of forming a functionally graded steel based on the use of a high molybdenum steel with cooper and other steel with copper, without molybdenum, is proposed with the aim of concentrating this element to the surface of the workpiece, increasing the mechanical strength. The study is completed with the evaluation of physical properties (density and porosity distribution, mechanical properties (hardness, tensile strength and elongation and microstructural analysis by optical and scanning electron microscopy.

  14. Chemical decontamination of stainless steel

    International Nuclear Information System (INIS)

    Onuma, Tsutomu; Akimoto, Hidetoshi

    1991-01-01

    The present invention concerns a method for chemical decontamination of radioactive metal waste materials contaminated with radioactive materials on the surface, generated in radioactive materials-handling facilities. The invention is comprised of a method of chemical decontamination of stainless steel, characterized by comprising a first process of immersing a stainless steel-based metal waste material contaminated by radioactive materials on the surface in a sulfuric acid solution and second process of immersing in an aqueous solution of sulfuric acid and oxidizing metal salt, in which a portion of the surface of the stainless steel to be decontaminated is polished mechanically to expose a portion of the base material before the above first and second processes. 1 figs., 2 tabs

  15. Corrosion of carbon steel welds

    International Nuclear Information System (INIS)

    Daniel, B.

    1988-09-01

    This report assesses the factors which cause preferential attack to occur in carbon steel fusion welds. It was concluded that the main factors were: the inclusion content of the weld metal, the potential of the weld metal being less noble than that of the parent, and the presence of low-temperature transformation products in the heat-affected zone of the weld. These factors should be minimized or eliminated as appropriate so that the corrosion allowances determined for carbon steel waste drums is also adequate for the welds. An experimental/theoretical approach is recommended to evaluate the relative corrosion resistance of welds prepared from BS 4360 grade 43A steel to that of the parent material. (author)

  16. Boron Steel: An Alternative for Costlier Nickel and Molybdenum Alloyed Steel for Transmission Gears

    Directory of Open Access Journals (Sweden)

    A. Verma

    2010-06-01

    Full Text Available Case Carburized (CC low carbon steels containing Ni, Cr and Mo alloying elements are widely used for transmission gears in automobile, as it possesses desired mechanical properties. In order to cut cost and save scarce materials like Ni and Mo for strategic applications, steel alloyed with Boron has been developed, which gives properties comparable to Ni-Cr-Mo alloyed steel. In the process of steel development, care was taken to ensure precipitation of boron which results in precipitation hardening. The characterization of the developed boron steel had exhibited properties comparable to Ni-Cr-Mo alloyed steel and superior to conventional boron steel.

  17. ESF GROUND SUPPORT - STRUCTURAL STEEL ANALYSIS

    Energy Technology Data Exchange (ETDEWEB)

    T. Misiak

    1996-06-26

    The purpose and objective of this analysis are to expand the level of detail and confirm member sizes for steel sets included in the Ground Support Design Analysis, Reference 5.20. This analysis also provides bounding values and details and defines critical design attributes for alternative configurations of the steel set. One possible configuration for the steel set is presented. This analysis covers the steel set design for the Exploratory Studies Facility (ESF) entire Main Loop 25-foot diameter tunnel.

  18. Corrosion behaviour of laser clad stainless steels

    International Nuclear Information System (INIS)

    Damborenea, J.J. de; Weerasinghe, V.M.; West, D.R.F.

    1993-01-01

    The present paper is focussed in the study of the properties of a clad layer of stainless steel on a mild steel. By blowing powder of the alloy into a melt pool generated by a laser of 2 KW, an homogeneous layer of 316 stainless steel can be obtained. Structure, composition and corrosion behaviour are similar to those of a stainless steel in as-received condition. (Author)

  19. Modern steels for light automobiles (review)

    Science.gov (United States)

    Tikhonov, A. K.

    1994-10-01

    The article considers the directions of work at VAZ together with metallurgists of the CIS for creating highly efficient economically-alloyed and microalloyed steels; highly ductile forged steels with improved corrosion resistance coated with zinc and with good stamping, welding, and painting capacity. Steels are created for petrol tanks with aluminum-zinc coatings instead of lead, and new heat and corrosion-resistant steels are developed for automobile exhaust gas systems.

  20. Inclusion control in high-performance steels

    International Nuclear Information System (INIS)

    Holappa, L.E.K.; Helle, A.S.

    1995-01-01

    Progress of clean steel production, fundamentals of oxide and sulphide inclusions as well as inclusion morphology in normal and calcium treated steels are described. Effects of cleanliness and inclusion control on steel properties are discussed. In many damaging constructional and engineering applications the nonmetallic inclusions have a quite decisive role in steel performance. An example of combination of good mechanical properties and superior machinability by applying inclusion control is presented. (author)

  1. Boron steel. I Part. Preparation

    International Nuclear Information System (INIS)

    Jaraiz Franco, E.; Esteban Hernandez, J. A.

    1960-01-01

    With the advent of the first nuclear reactors arise the need for control rods and shielding duties for some types of radiations. One of the materials used for this purpose has been the high boron steel. This paper describes the melting and casting procedures employed for the production, at laboratory scale, of steels with Boron content ranging from 1 to 4 per cent, as well as the metallographic and X-Ray techniques used for the identification of the present phases. The electrolytic technique employed for the isolation of the Fe 2 B phase and its subsequent X-Ray identification has proved to be satisfactory. (Author) 11 refs

  2. Plating on stainless steel alloys

    International Nuclear Information System (INIS)

    Dini, J.W.; Johnson, H.R.

    1981-01-01

    Quantitative adhesion data are presented for a variety of electroplated stainless steel type alloys. Results show that excellent adhesion can be obtained by using a Wood's nickel strike or a sulfamate nickel strike prior to final plating. Specimens plated after Wood's nickel striking failed in the deposit rather than at the interface between the substrate and the coating. Flyer plate quantitative tests showed that use of anodic treatment in sulfuric acid prior to Wood's nickel striking even further improved adhesion. In contrast activation of stainless steels by immersion or cathodic treatment in hydrochloric acid resulted in very reduced bond strengths with failure always occurring at the interface between the coating and substrate

  3. Steeling and Resilience in Art Education

    Science.gov (United States)

    Heise, Donalyn

    2014-01-01

    Steel is an incredibly strong alloy of iron and carbon. Due to its incredible strength and durability, this resilient material is commonly used for constructing buildings. The transitive verb "steeling" is defined in Miriam-Webster dictionary as "to fill with resolution or determination, as in, she 'steeled herself to face the…

  4. A model for TRIP steel constitutive behaviour

    NARCIS (Netherlands)

    Perdahcioglu, Emin Semih; Geijselaers, Hubertus J.M.; Menari, G

    2011-01-01

    A constitutive model is developed for TRIP steel. This is a steel which contains three or four different phases in its microstructure. One of the phases in TRIP steels is metastable austenite (Retained Austenite) which transforms to martensite upon deformation. The accompanying transformation strain

  5. Microstructural Development during Welding of TRIP steels

    NARCIS (Netherlands)

    Amirthalingam, M.

    2010-01-01

    The Advanced High Strength Steels (AHSS) are promising solutions for the production of lighter automobiles which reduce fuel consumption and increase passenger safety by improving crash-worthiness. Transformation Induced Plasticity Steel (TRIP) are part of the advanced high strength steels which

  6. performance of steel slag performance of steel slag as fine

    African Journals Online (AJOL)

    eobe

    Suitability of using steel slag (SS) as substitute for sand in concrete was ... The strength of SS concrete increased with increase in proporti. 10 mm. .... additives used. All other oxides ..... low lime coal fly ash in foamed concrete”, Fuel, Vol. 84,.

  7. Teaching Steel Connections Using an Interactive Virtual Steel Sculpture

    Science.gov (United States)

    Moaveni, Saeed; Chou, Karen C.

    2015-01-01

    Steel connections play important roles in the integrity of a structure, and many structural failures are attributed to connection failures. Connections are the glue that holds a structure together. The failures of the Hartford Coliseum in 1977, the Hyatt Regency Hotel in Kansas City in 1980, and the I-35W Bridge in Minneapolis in 2007 are all…

  8. Physical characterization of steel and stainless steel metal powders

    International Nuclear Information System (INIS)

    Lavilla, A.O.; Lucchesi, C.G.; Sandin, O.O.

    1991-01-01

    A methodology has been developed for the physical characterization of steel powders (obtained by atomization) for later sintering and for the construction of porous sheets and filtrating tubes, capable of operating at temperatures between 600 deg C and 800 deg C in corrosive atmospheres. This methodology was based on the equipment and methods used for the physical characterization of uranium oxide powders. (Author) [es

  9. Some comments about the situation of the Steel Industry in the Arab Countries (Arab Steel Summit)

    International Nuclear Information System (INIS)

    Haidar, Y.; Astier, J.

    2009-01-01

    The Arab Steel Summit, that convened in Abu Dhabi in April, gave us another opportunity to review the situation of the Arab Iron and Steel Industry, with regard to the present World economic context. We will address: - the World situation of steel production, focusing on the Arab Countries; - the related situation of steel consumption; - the steel trade, including imports, exports and prices; - the consequences for technology and economy. (authors)

  10. Comparative benefit of malaria chemoprophylaxis modelled in United Kingdom travellers.

    Science.gov (United States)

    Toovey, Stephen; Nieforth, Keith; Smith, Patrick; Schlagenhauf, Patricia; Adamcova, Miriam; Tatt, Iain; Tomianovic, Danitza; Schnetzler, Gabriel

    2014-01-01

    Chemoprophylaxis against falciparum malaria is recommended for travellers from non-endemic countries to malarious destinations, but debate continues on benefit, especially with regard to mefloquine. Quantification of benefit for travellers from the United Kingdom (UK) was modelled to assist clinical and public health decision making. The model was constructed utilising: World Tourism Organization data showing total number of arrivals from the UK in countries with moderate or high malaria risk; data from a retrospective UK Clinical Practice Research Datalink (CPRD) drug utilisation study; additional information on chemoprophylaxis, case fatality and tolerability were derived from the travel medicine literature. Chemoprophylaxis with the following agents was considered: atovaquone-proguanil (AP), chloroquine with and without proguanil (C ± P), doxycycline (Dx), mefloquine (Mq). The model was validated for the most recent year with temporally matched datasets for UK travel destinations and imported malaria (2007) against UK Health Protection Agency data on imported malaria. The median (mean) duration of chemoprophylaxis for each agent in weeks (CPRD) was: AP 3.3 (3.5), C ± P 9 (12.1), Dx 8 (10.3), Mq 9 (12.3): the maximum duration of use of all regimens was 52 weeks. The model correctly predicted falciparum malaria deaths and gave a robust estimate of total cases--model: 5 deaths from 1118 cases; UK Health Protection Agency: 5 deaths from 1153 cases. The number needed to take chemoprophylaxis (NNP) to prevent a case of malaria considered against the 'background' reported incidence in non-users of chemoprophylaxis deemed in need of chemoprophylaxis was: C ± P 272, Dx 269, Mq 260, AP 252; the NNP to prevent a UK traveller malaria death was: C ± P 62613, Dx 61923, Mq 59973, AP 58059; increasing the 'background' rate by 50% yielded NNPs of: C ± P 176, Dx 175, Mq 171, AP 168. The impact of substituting atovaquone-proguanil for all mefloquine usage resulted in a 2

  11. Preface and summary of the United Kingdom contributions

    International Nuclear Information System (INIS)

    Nettley, P.T.

    1980-01-01

    The mechanical integrity of engineering structures is a matter of great practical importance for both economic and safety reasons. In practice this integrity must be assured by careful attention to many aspects of design, materials, fabrication, inspection etc. An important uncertainty is the possible presence of defects in the structure. Under appropriate circumstances, such defects can grow during service until they reach the size where they extend unstably and thus cause the failure of critical sections of the structure and the structure itself. The design and operation of these structures must therefore take account of the possible presence of cracks. The conventional approach is one based upon a set of conservative assumptions about the maximum defect size, nature and frequency of loadings on the structure, the materials properties, particularly crack growth rates and fracture toughness, etc. However many of these quantities are statistically distributed and we can never be absolutely sure that values worse than the chosen conservative limits will not be encountered. This is probably true of the relevant materials and must likewise be true of transient loadings. These uncertainties therefore oblige us to try to reduce failure probabilities in plant components by design, materials selection, manufacture, quality control, and pre-service and in-service inspection and monitoring. At this Specialist Meeting we are going to concentrate on in-service inspection and monitoring of LMFBRs. However, the techniques applicable to in-service inspection can of course be applied pre-service and it is generally recognised in the United Kingdom that there is a great need for intensive inspection of LMFBR plant both during and on completion of manufacture. Current experience indicates that design proposals for new reactors should pay particular attention to access, inspectability and replaceability. Because the environment experienced by components in large sodium cooled fast

  12. Molecular Epidemiology of Rotavirus in Cats in the United Kingdom

    Science.gov (United States)

    Iturriza-Gómara, M.; Dove, W.; Sandrasegaram, M.; Nakagomi, T.; Nakagomi, O.; Cunliffe, N.; Radford, A. D.; Morgan, K. L.

    2014-01-01

    Rotaviruses are leading causes of gastroenteritis in the young of many species. Molecular epidemiological studies in children suggest that interspecies transmission contributes to rotavirus strain diversity in people. However, population-based studies of rotaviruses in animals are few. We investigated the prevalence, risk factors for infection, and genetic diversity of rotavirus A in a cross-sectional survey of cats housed within 25 rescue catteries across the United Kingdom. Morning litter tray fecal samples were collected during the winter and summer in 2012 from all pens containing kittens and a random sample of those housing adult cats. Group A rotavirus RNA was detected by real-time reverse transcription-PCR, and positive samples were G and P genotyped using nested VP4 and VP7 PCR assays. A total of 1,727 fecal samples were collected from 1,105 pens. Overall, the prevalence of rotavirus was 3.0% (95% confidence interval [CI], 1.2 to 4.9%). Thirteen out of 25 (52%; 95% CI, 31.3 to 72.2%) centers housed at least one rotavirus-positive cat. The prevalence of rotavirus was associated with season (odds ratio, 14.8 [95% CI, 1.1 to 200.4]; P = 0.04) but not age or diarrhea. It was higher during the summer (4.7%; 95% CI, 1.2 to 8.3%) than in winter (0.8%; 95% CI, 0.2 to 1.5%). Asymptomatic epidemics of infection were detected in two centers. G genotypes were characterized for 19 (33.3%) of the 57 rotavirus-positive samples and P genotypes for 36 (59.7%). Two rotavirus genotypes were identified, G3P[9] and G6P[9]. This is the first population-based study of rotavirus in cats and the first report of feline G6P[9], which questions the previous belief that G6P[9] in people is of bovine origin. PMID:25411173

  13. The lands west of the lakes; A history of the Ajattappareng kingdoms of South Sulawesi 1200 to 1600 CE

    OpenAIRE

    Druce, Stephen C.

    2009-01-01

    The period 1200-1600 CE saw a radical transformation from simple chiefdoms to kingdoms (in archaeological terminology, complex chiefdoms) across lowland South Sulawesi, a region that lay outside the ‘classical’ Indicized parts of Southeast Asia. The rise of these kingdoms was stimulated and economically supported by trade in prestige goods with other parts of island Southeast Asia, yet the development of these kingdoms was determined by indigenous, rather than imported, political and cultural...

  14. Review of operational experience with the gas-cooled Magnox reactors of the United Kingdom Central Electricity Generating Board

    International Nuclear Information System (INIS)

    Cave, L.; Clarke, A.W.

    1984-01-01

    The paper provides a review, which is mainly of a statistical nature, of 260 reactor years of operating experience which the (United Kingdom) Central Electricity Generating Board (CEGB) has obtained with its gas-cooled, graphite moderated Magnox reactors. The main emphasis in the review is on safety rather than on availability. Data are provided on the overall incidence and frequencies of faults and it is shown that the plant items which are predominantly responsible for recorded faults are the gas circulators and the turbo-alternators. Analysis of the reactor trip experience shows that the incidence of events which necessitate an automatic shutdown of the reactor has been about one per reactor year and that of other events leading to a reactor trip has not been much higher (1.4 per reactor year). As would be expected from the length of the operating experience, some relatively rare events have occurred (expected frequency 10 -2 per reactor year, or less) but on each occasion the reactor shutdown system and decay heat removal systems functioned satisfactorily. No overheating of, or damage to, the fuel occurred as a result of these rare events or of other, more frequent, faults. Analysis of the trend of failure rates has shown an improvement with time in nearly all safety-related items and external inspection of the primary coolant circuits has shown no significant deterioration with time. However, some derating of the reactors has been necessary to reduce the effects of oxidation of mild steel in CO 2 , in order to obtain optimum service lives. In spite of major differences between the systems, a comparison of the failure rates of analogous systems and plant items in PWRs and the Magnox reactors show a considerable similarity. Overall, the review of CEGB's operational experience with its Magnos reactors has shown that the frequencies of faults in systems and plant items has been satisfyingly low. (author)

  15. Fabrication of californium-252 sources in the United Kingdom

    International Nuclear Information System (INIS)

    Ainsworth, A.; Brady, M.W.; Thornett, W.H.

    1975-01-01

    The advent of californium-252 in weighable quantities and at a reasonable price has caused some rethinking among neutron source suppliers. To explore this market the Radiochemical Center Ltd. has purchased 2 mg of californium-252, and subdivided this into a wide range of sources. To take advantage of its high specific neutron emission, a small double welded stainless steel capsule 7.8mm diameter x 10mm high was chosen for stock sources and this entailed the use of a microdispensing technique which had to be specially developed. The apparatus and procedure for subdividing milligram amounts of californium-252 are described. Some details of our experience in processing these one milligram shipments are given. 100 sources with activities from 200 microgram to 0.01 microgram have been produced. Losses have been small. Measurement of neutron spectra gamma spectra and dose rates from encapsulated sources has confirmed published data. Though it is early days, little industrial interest in californium-252 sources has been detected, most of the sources have so far been required for research into activation analysis and two examples of this are given. (U.S.)

  16. The Private New Kingdom Tombs of Amarna, Thebes and Memphis: their relations to the architecture of private houses and temples

    OpenAIRE

    Veigel, Isabell

    2010-01-01

    This thesis refers to the architecture of the New Kingdom tombs in Amarna, Thebes and Memphis in terms of the influence between the architecture of houses, tombs and temples. Is it possible to transfer Diodor´s statement about the Egyptian tombs as “houses for the eternity” from Roman times into the New Kingdom? Do the New Kingdom tombs show the same characteristics as the architectural remains of the New Kingdom houses? With a comprehensive analysis of the architecture of tombs, houses an...

  17. Inching toward incrementalism: federalism, devolution, and health policy in the United States and the United Kingdom.

    Science.gov (United States)

    Sparer, Michael S; France, George; Clinton, Chelsea

    2011-02-01

    In the United States, the recently enacted Patient Protection and Affordable Care Act of 2010 envisions a significant increase in federal oversight over the nation's health care system. At the same time, however, the legislation requires the states to play key roles in every aspect of the reform agenda (such as expanding Medicaid programs, creating insurance exchanges, and working with providers on delivery system reforms). The complicated intergovernmental partnerships that govern the nation's fragmented and decentralized system are likely to continue, albeit with greater federal oversight and control. But what about intergovernmental relations in the United Kingdom? What impact did the formal devolution of power in 1999 to Scotland, Wales, and Northern Ireland have on health policy in those nations, and in the United Kingdom more generally? Has devolution begun a political process in which health policy in the United Kingdom will, over time, become increasingly decentralized and fragmented, or will this "state of unions" retain its long-standing reputation as perhaps the most centralized of the European nations? In this article, we explore the federalist and intergovernmental implications of recent reforms in the United States and the United Kingdom, and we put forward the argument that political fragmentation (long-standing in the United States and just emerging in the United Kingdom) produces new intergovernmental partnerships that, in turn, produce incremental growth in overall government involvement in the health care arena. This is the impact of what can be called catalytic federalism.

  18. Creating an innovative youth mental health service in the United Kingdom: The Norfolk Youth Service.

    Science.gov (United States)

    Wilson, Jon; Clarke, Tim; Lower, Rebecca; Ugochukwu, Uju; Maxwell, Sarah; Hodgekins, Jo; Wheeler, Karen; Goff, Andy; Mack, Robert; Horne, Rebecca; Fowler, David

    2017-08-04

    Young people attempting to access mental health services in the United Kingdom often find traditional models of care outdated, rigid, inaccessible and unappealing. Policy recommendations, research and service user opinion suggest that reform is needed to reflect the changing needs of young people. There is significant motivation in the United Kingdom to transform mental health services for young people, and this paper aims to describe the rationale, development and implementation of a novel youth mental health service in the United Kingdom, the Norfolk Youth Service. The Norfolk Youth Service model is described as a service model case study. The service rationale, national and local drivers, principles, aims, model, research priorities and future directions are reported. The Norfolk Youth Service is an innovative example of mental health transformation in the United Kingdom, comprising a pragmatic, assertive and "youth-friendly" service for young people aged 14 to 25 that transcends traditional service boundaries. The service was developed in collaboration with young people and partnership agencies and is based on an engaging and inclusive ethos. The service is a social-recovery oriented, evidence-based and aims to satisfy recent policy guidance. The redesign and transformation of youth mental health services in the United Kingdom is long overdue. The Norfolk Youth Service represents an example of reform that aims to meet the developmental and transitional needs of young people at the same time as remaining youth-oriented. © 2017 John Wiley & Sons Australia, Ltd.

  19. Steel story founded on coal

    Energy Technology Data Exchange (ETDEWEB)

    1977-01-01

    Paper reports on an iron and steel plant in New Zealand which uses non-coking subbituminuous coal to produce the sponge iron. The transport of the ironsand and the coal to the site and the operation of the kiln in which the ironsand is reduced by the coal is described.

  20. Metadynamic recrystallization in C steels

    Indian Academy of Sciences (India)

    Metadynamic recrystallization has been investigated in three plain carbon steels (ENIA, EN2 and EN24) through the use of hot interrupted compression tests on a wedge plastometer. Holding time was 0.5 s between passes. Strain rates of 0.05 and 0.12/s and small strain increments of 3, 5 and 7% were employed.

  1. Corrosion of austenitic stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Silva, M C.M. [Instituto Nacional de Tecnologia, Rio de Janeiro (Brazil)

    1977-01-01

    Types of corrosion observed in a heat exchanger pipe and on a support of still of molasses fermented wort, both in austenitic stainless steel, are focused. Not only are the causes which might have had any kind of influence on them examined, but also the measures adopted in order to avoid and lessen its occurence.

  2. Fatigue Strength of Weathering Steel

    Czech Academy of Sciences Publication Activity Database

    Kunz, Ludvík; Lukáš, Petr; Klusák, Jan

    2012-01-01

    Roč. 18, č. 1 (2012), s. 18-22 ISSN 1392-1320 Grant - others:GA MPO(CZ) FT/TA5/076 Institutional support: RVO:68081723 Keywords : fatigue of weathering steel * corrosion pits * fatigue notch factor Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 0.522, year: 2012

  3. Argon solubility in liquid steel

    NARCIS (Netherlands)

    Boom, R; Dankert, O; Van Veen, A; Kamperman, AA

    2000-01-01

    Experiments have been performed to establish the solubility of argon in liquid interstitial-free steel. The solubility appears to be lower than 0.1 at ppb, The results are in line with argon solubilities reported in the literature on liquid iron. Semiempirical theories and calculations based on the

  4. Kinetics of borided gear steels

    Indian Academy of Sciences (India)

    ration (FeB + Fe2B) due to the high intensity stress states generally situated at the ... performed molten salt boriding of AISI D2 steel with borax (Na2B4O7) as the ... the borided layer thickness; silicon, chromium and aluminium have moderate.

  5. Development of PWR pressure vessel steels

    International Nuclear Information System (INIS)

    Druce, S.; Edwards, B.

    1982-01-01

    Requirements to be met by vessel steels for pressurized water reactors are analyzed. Chemicat composition of low-alloyed steels, mechanical properties of sheets and forgings made of these steels and changes in the composition and properties over the wall thickness of the reactor vessel are presented. Problems of the vessel manufacturing including welding and heat treatment processes of sheets and forgings are considered. Special attention is paid to steel embrittlement during vessel fabrication and operation (radiation embrittlement, thermal embrittlement). The role of non-metal inclusions and their effect on anisotropy of fracture toughness is discussed. Possible developments of vessel steels and procedures for producing reactor vessels are reviewed

  6. Development of PWR pressure vessel steels

    Energy Technology Data Exchange (ETDEWEB)

    Druce, S.; Edwards, B.

    1982-01-01

    Requirements to be met by vessel steels for pressurized water reactors are analyzed. Chemicat composition of low-alloyed steels, mechanical properties of sheets and forgings made of these steels and changes in the composition and properties over the wall thickness of the reactor vessel are presented. Problems of the vessel manufacturing including welding and heat treatment processes of sheets and forgings are considered. Special attention is paid to steel embrittlement during vessel fabrication and operation (radiation embrittlement, thermal embrittlement). The role of non-metal inclusions and their effect on anisotropy of fracture toughness is discussed. Possible developments of vessel steels and procedures for producing reactor vessels are reviewed.

  7. High - speed steel for precise cased tools

    International Nuclear Information System (INIS)

    Karwiarz, J.; Mazur, A.

    2001-01-01

    The test results of high-vanadium high - speed steel (SWV9) for precise casted tools are presented. The face -milling cutters of NFCa80A type have been tested in industrial operating conditions. An average life - time of SWV9 steel tools was 3-10 times longer compare to the conventional high - speed milling cutters. Metallography of SWB9 precise casted steel revealed beneficial for tool properties distribution of primary vanadium carbides in the steel matrix. Presented results should be a good argument for wide application of high - vanadium high - speed steel for precise casted tools. (author)

  8. Study on cementitious properties of steel slag

    Directory of Open Access Journals (Sweden)

    Zhu G.

    2013-01-01

    Full Text Available The converter steel slag chemical and mineral components in China’s main steel plants have been analysed in the present paper. The electronic microscope, energy spectrum analysis, X-ray diffraction analysis confirmed the main mineral compositions in the converter slag. Converter slag of different components were grounded to obtain a powder with specific surface area over 400m2/kg, making them to take place some part of the cement in the concrete as the admixture and carry out the standard tests. The results indicate that the converter slag can be used as cementitious materials for construction. Furthermore, physical mechanic and durability tests on the concrete that certain amount of cement be substituted by converter steel slag powder from different steel plants are carried out, the results show that the concrete with partial substitution of steel slag powder has the advantages of higher later period strength, better frost resistance, good wear resistance and lower hydration heat, etc. This study can be used as the technical basis for “Steel Slag Powder Used For Cement And Concrete”, “Steel Slag Portland Cement”, “Low Heat Portland Steel Slag Cement”, “Steel Slag Road Cement” in China, as well as a driving force to the works of steel slag utilization with high-value addition, circular economy, energy conservation and discharge reduction in the iron and steel industry.

  9. Corrosion behavior of 2205 duplex stainless steel.

    Science.gov (United States)

    Platt, J A; Guzman, A; Zuccari, A; Thornburg, D W; Rhodes, B F; Oshida, Y; Moore, B K

    1997-07-01

    The corrosion of 2205 duplex stainless steel was compared with that of AISI type 316L stainless steel. The 2205 stainless steel is a potential orthodontic bracket material with low nickel content (4 to 6 wt%), whereas the 316L stainless steel (nickel content: 10 to 14 wt%) is a currently used bracket material. Both stainless steels were subjected to electrochemical and immersion (crevice) corrosion tests in 37 degrees C, 0.9 wt% sodium chloride solution. Electrochemical testing indicates that 2205 has a longer passivation range than 316L. The corrosion rate of 2205 was 0.416 MPY (milli-inch per year), whereas 316L exhibited 0.647 MPY. When 2205 was coupled to 316L with equal surface area ratio, the corrosion rate of 2205 reduced to 0.260 MPY, indicating that 316L stainless steel behaved like a sacrificial anode. When 316L is coupled with NiTi, TMA, or stainless steel arch wire and was subjected to the immersion corrosion test, it was found that 316L suffered from crevice corrosion. On the other hand, 2205 stainless steel did not show any localized crevice corrosion, although the surface of 2205 was covered with corrosion products, formed when coupled to NiTi and stainless steel wires. This study indicates that considering corrosion resistance, 2205 duplex stainless steel is an improved alternative to 316L for orthodontic bracket fabrication when used in conjunction with titanium, its alloys, or stainless steel arch wires.

  10. STEFINS: a steel freezing integral simulation program

    International Nuclear Information System (INIS)

    Frank, M.V.

    1980-09-01

    STEFINS (STEel Freezing INtegral Simulation) is a computer program for the calculation of the rate of solidification of molten steel on solid steel. Such computations arize when investigating core melt accidents in fast reactors. In principle this problem involves a coupled two-dimensional thermal and hydraulic approach. However, by physically reasonable assumptions a decoupled approach has been developed. The transient solidification of molten steel on a cold wall is solved in the direction normal to the molten steel flow and independent from the solution for the molten steel temperature and Nusselt number along the direction of flow. The solutions to the applicable energy equations have been programmed in cylindrical and slab geometries. Internal gamma heating of steel is included

  11. Irradiation embrittlement of pressure vessel steels

    International Nuclear Information System (INIS)

    Brumovsky, M.; Vacek, M.

    1975-01-01

    A Standard Research Programme on Irradiation Embrittlement of Pressure Vessel Steels was approved by the Coordinating Meeting on the 12th May 1972 at the Working Group on Engineering Aspects of Irradiation Embrittlement of Pressure Vessel Steels. This Working Group was set up by the International Atomic Energy Agency in Vienna. Seven countries with their research institutes agreed on doing irradiation experiments according to the approved programme on steel A533 B from the U.S. HSST Programme. The Czechoslovak contribution covering tensile and impact testing of non-irradiated steel and steel irradiated at 280degC to 1.3 x 10 23 n/m 2 (E above 1 MeV) is presented in this report. As an additional part the same set of experiments was carried out on two additional steels - A 542 and A 543, made in SKODA Works for comparison of their irradiation embrittlement and hardening with A533 B steel. (author)

  12. Development of design procedures for fast reactors in the United Kingdom

    International Nuclear Information System (INIS)

    Rose, R.T.; Tomkins, B.; Townley, C.H.A.

    1989-01-01

    A considerable amount of research has been carried out in the United Kingdom during the past two decades to quantify the factors which control the integrity of structural components. The work which has been aimed at understanding the performance of structures at high temperature, is particularly relevant to the Fast Reactor. At the same time, because of the need to demonstrate the tolerance to defects in the low temperature as well as the high temperature components, defect assessment criteria are also of great importance. Emphasis is now being given to the development of design procedures specifically for Fast Reactors, making use of the research so far completed. The United Kingdom proposals are being integrated with those from France, Federal Republic of Germany and Italy as part of the European collaborative venture. The paper outlines the major developments which are currently in hand, and brings up to date the review of United Kingdom activities presented at Tokyo in 1986. (author)

  13. COMPARATIVE LEGISLATIVE ANALYSIS OF ACTIVE BRIBERY IN THE UNITED KINGDOM OF GREAT BRITAIN AND NORTHERN IRELAND

    Directory of Open Access Journals (Sweden)

    Mijo Galiot

    2015-01-01

    Full Text Available Confronting socially unacceptable activities, especially corruptive criminal acts, including bribing, makes an important issue of every regulated legal system. The crucial part of such policies are the criminal polices. In this paper, the author deals with the criminal legislation of the United Kingdom of Great Britain and Northern Ireland, related to the matters of active bribing as one of the basic forms of corruptive behaviour. While comparing the way the penal system is regulated in the said country, the author comments basic similarities and differences of the passive bribing legal regulation in the United Kingdom and the Republic of Croatia.

  14. Seismic design criteria and their application to major hazard plant within the United Kingdom

    International Nuclear Information System (INIS)

    Alderson, M.A.H.G.

    1982-12-01

    The nature of seismic motions and the implications are briefly described and the development of seismic design criteria for nuclear power plants in various countries is described including possible future developments. The seismicity of the United Kingdom is briefly reviewed leading to the present position on seismic design criteria for nuclear power plants within the United Kingdom. Damage from past destructive earthquakes is reviewed and the existing codes of practice and standards are described. Finally the effect of earthquakes on major hazard plant is discussed in general terms including the seismic analysis of a typical plant item. (author)

  15. Earthquake response of steel braces and braced steel frames

    OpenAIRE

    Gan, Wenshui

    1996-01-01

    This thesis consists of three parts. Chapter 2 deals with the dynamic buckling behavior of steel braces under cyclic axial end displacement. Braces under such a loading condition belong to a class of "acceleration magnifying" structural components, in which a small motion at the loading points can cause large internal acceleration and inertia. This member-level inertia is frequently ignored in current studies of braces and braced structures. This chapter shows that, under certain conditions, ...

  16. Advanced cold rolled steels for automotive applications

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, Harald; Mattissen, Dorothea; Schaumann, Thomas Wilhelm [ThyssenKrupp Steel AG, Center of Materials Excellence, Dortmund (Germany)

    2009-01-15

    Advanced high-strength steels offer a great potential for the further development of automobile bodies-in-white due to their combined mechanical properties of high formability and strength. They represent the first choice in material selection for strength and crash-relevant parts with challenging geometries. The intensive development of multiphase steels by ThyssenKrupp Steel has led to hot dip galvanizing concepts with an outstanding forming potential. Hot rolled, hot dip galvanized complex-phase steels are currently produced in addition to cold rolled dual phase (DP) and retained austenite (RA) or transformation induced plasticity (TRIP) steels. New continuously annealed grades of steel are being developed with tensile strength levels of up to 1000 MPa in combination with sufficient ductility for the high demands of structural automobile components. These steels make use of the classic advantages of microalloying as well as the principles of DP steels and RA / TRIP steels. Further improvement of properties will be reached by the new class of high manganese alloyed steels. (orig.)

  17. On high temperature strength of carbon steels

    International Nuclear Information System (INIS)

    Ichinose, Hiroyuki; Tamura, Manabu; Kanero, Takahiro; Ihara, Yoshihito

    1977-01-01

    In the steels for high temperature use, the oxidation resistance is regarded as important, but carbon steels show enough oxidation resistance to be used continuously at the temperature up to 500 deg. C if the strength is left out of consideration, and up to 450 deg. C even when the strength is taken into account. Moreover, the production is easy, the workability and weldability are good, and the price is cheap in carbon steels as compared with alloy steels. In the boilers for large thermal power stations, 0.15-0.30% C steels are used for reheater tubes, main feed water tubes, steam headers, wall water tubes, economizer tubes, bypass pipings and others, and they account for 70% of all steel materials used for the boilers of 350 MW class and 30% in 1000 MW class. The JIS standard for the carbon steels for high temperature use and the related standards in foreign countries are shown. The high temperature strength of carbon steels changes according to the trace elements, melting and heat treatment as well as the main compositions of C, Si and Mn. Al and N affect the high temperature strength largely. The characteristics of carbon steels after the heating for hours, the factors controlling the microstructure and high temperature strength, and the measures to improve the high temperature strength of carbon steels are explained. (Kako, I.)

  18. Dismantling the Perceived Barriers to the Implementation of National Higher Education Accreditation Guidelines in the Kingdom of Saudi Arabia

    Science.gov (United States)

    Onsman, Andrys

    2010-01-01

    The Kingdom of Saudi Arabia has invested heavily in its social sector, especially in setting up new schools and universities. The aim of the development is to prepare the Kingdom for a future that is not dependent on its oil resources which are predicted to run out in less than a hundred years. Driven by the country's monarch, King Abdullah, many…

  19. 48 CFR 252.229-7009 - Relief from customs duty and value added tax on fuel (passenger vehicles) (United Kingdom).

    Science.gov (United States)

    2010-10-01

    ... and value added tax on fuel (passenger vehicles) (United Kingdom). 252.229-7009 Section 252.229-7009... Relief from customs duty and value added tax on fuel (passenger vehicles) (United Kingdom). As prescribed in 229.402-70(i), use the following clause: Relief from Customs Duty and Value Added Tax on Fuel...

  20. 78 FR 58378 - Culturally Significant Objects Imported for Exhibition Determinations: “Peru: Kingdoms of the Sun...

    Science.gov (United States)

    2013-09-23

    ... DEPARTMENT OF STATE [Public Notice 8478] Culturally Significant Objects Imported for Exhibition Determinations: ``Peru: Kingdoms of the Sun and the Moon'' SUMMARY: Notice is hereby given of the following... ``Peru: Kingdoms of the Sun and the Moon,'' imported from abroad for temporary exhibition within the...