The hydrogen isotopic composition of kaolin minerals in Japan

International Nuclear Information System (INIS)

Marumo, Katsumi; Nagasawa, Keinosuke; Kuroda, Yoshimasu.

1979-01-01

Hydrogen isotopic composition (D/H ratio) was determined for kaolin minerals from geothermal areas and sedimentary and hydrothermal kaolin deposits in Japan. On the Ohnuma, Matsukawa, and Ohtake geothermal areas, the hydrogen isotopic fractionation factor between kaolin minerals and water was calculated to fall between 0.97 and 0.99 for the temperature range of 50 to 200 0 C, a fact which shows that the temperature of formation has no important effect on the D/H ratio of kaolin minerals. D/H ratio of kaolinites and dickites from many kaolin deposits shows local variation, and seems to correlate with isotopic variation of the present-day meteoric surface water. Exceptions are seen in some kaolin deposits such as Shokozan, Hiroshima Prefecture, where kaolinite and dickite have considerably high values of D/H ratio, and seem to have reacted with water rich in deuterium. D/H ratio of halloysite is not correlated with that of the present-day meteoric surface water. As Lawrence and Taylor (1971) pointed out, the original D/H ratio of constitutional water of halloysite is not preserved because of the isotopic exchange between the interlayer water and the constitutional water. (author)

XANES at the silicon k-edge in the kaolin-meta kaolin-geopolymer system

International Nuclear Information System (INIS)

Lima, F.T.; Silva, F.J.; Thaumaturgo, C.

2005-01-01

The geo polymer synthesis process optimization pretends to control the re logical and mechanical properties. The Al/Si ratio is the main variable that governs the geo polymerization process. This control occurs by changing temperature, pressure and chemical composition of the geo polymer. Thermal analysis (DTA/DSC), microscopic (SEM/TEM) and spectroscopic (FTIR, XRD, SAXS, EXAFS and XANES) techniques have been used to characterize these inorganic systems. In this work, XANES spectra of the k-edge silicon (Si) of the kaolin-meta kaolin-geo polymer are presented. The XANES spectra provides the oxidation state and structural information about the present studied atom: Silicon (Si). (author)

Effect of surface modified kaolin on properties of polypropylene grafted maleic anhydride

Science.gov (United States)

Yang, Ni; Zhang, Zuo-Cai; Ma, Ning; Liu, Huan-Li; Zhan, Xue-Qing; Li, Bing; Gao, Wei; Tsai, Fang-Chang; Jiang, Tao; Chang, Chang-Jung; Chiang, Tai-Chin; Shi, Dean

To achieve reinforcement of mechanical and thermal performances of polypropylene (PP) product, this work aimed at fabrication of surface modified kaolin (M-kaolin) filled polypropylene grafted maleic anhydride (PP-g-MAH) composites with varying contents of fillers and investigation of their mechanical and thermal properties. And the prepared PP-g-MAH/M-kaolin composites were characterized by means of Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). Fracture analysis by SEM showed M-kaolin particles were well dispersed in the PP-g-MAH matrix. Mechanical behaviors were determined by tensile strength, tensile strain at break and impact strength analysis. Impact strength of PP-g-MAH/2 wt% M-kaolin composites was improved up to 30% comparing with unfilled composites. Thermostability had been found enhanced when M-kaolin added. The results revealed PP-g-MAH/M-kaolin composites showed the optimal thermal and mechanical properties when 2 wt% of M-kaolin was added.

PENGARUH METODE AKTIVASI PADA KEMAMPUAN KAOLIN SEBAGAI ADSORBEN BESI (FE AIR SUMUR GARUDA

Directory of Open Access Journals (Sweden)

Tirta Indah Wulan Sari

2016-10-01

Full Text Available Kaolin is a mineral found in sedimentary rocks known as clay stone. Kaolin widely applied in industries such as paper, ceramics, rubber, plastics, paint, glassfiber, and cosmetics. This study aimed to determine the effect on the ability of kaolin activation methods as adsorbent. The study was conducted by activation of kaolin in physics, chemistry, and chemistry-physics. Physical activation was done by heating kaolin at 700 ° C in a furnace for 30 minutes and for the chemical activation, the addition of 0.25 M HCl in kaolin with stirring speed of 200 rpm for 60 minutes, while the chemical-physical activation, the addition of 0.25 M HCl to the kaolin and continued warming in furnace at 700 ° C. The kaolin activation was to produce an adsorbent that is able to absorb iron (Fe optimally. From this study, the optimum activation obtained for kaolin in adsorbing Fe is the chemical activation. Chemical activated kaolin adsorbent having a large adsorption capacity of the ion Fe which resulted in decreased content of iron (Fe to 0.04 mg / L.

X-ray diffraction and thermal analysis of kaolins particle size fractions

Directory of Open Access Journals (Sweden)

Patricia dos Santos

2013-09-01

Full Text Available Kaolins are common geological materials and have high concentrations of kaolinite as well as the clay fraction of tropical and subtropical soils of Brazil. The characterization of kaolin is a proxy of assessing the contribution of kaolinite to important soil chemical and mineralogical attributes. This study evaluated four kaolins (commercial kaolin A (CCA, commercial kaolin B (CCB, pink sandy kaolin A (CRA and green sandy kaolin A (CVA in the original form and after particle size separation into: sand (200-53 mm, coarse silt (53-20 m, fine silt (20-2 m, large clay (2-1m, medium clay (1-0.5 m and fine clay (<0.5m fractions. The minerals were identified by X-ray diffraction (XRD and evaluated for crystallinity (kaolinite and halloysite through indexes Hughes and Brown, Amigó, Bramão and the dehydroxylation temperature. The physical fractionation was efficient to concentrate minerals in specific size fractions which were not identified in the original material. In CCA kaolin was concentrated one mineral which remains unidentified in fine fractions, in kaolin CRA, zircon was concentrated in the coarse silt and different silicates in the fine fractions, in kaolin CCB were concentrated kaolinite and a silicate in the medium and coarse clay fractions. The estimate by X-ray diffraction overestimated the amount of kaolinite and halloysite underestimated when compared to quantification by thermal gravimetric analysis The crystallinity index exhibit different behaviors depending on the mineralogy of each material, thus the correlation between the crystallinity of kaolinite and / or halloysite and other variables, may be compromised, especially in materials with distinct geological origins.

ADSORPTION OF PARAQUAT DICHLORIDE TO KAOLIN PARTICLES AND TO MIXTURES OF KAOLIN AND HEMATITE PARTICLES

Directory of Open Access Journals (Sweden)

Dina Alexandra Martins

2015-03-01

Full Text Available Deliberate contamination with pesticides is a potential risk to water security, due to the availability of these contaminants and the fact that they do not need special expertise to handle or apply. Adsorption of the herbicide paraquat from an aqueous solution to suspended particles of kaolin and kaolin/hematite mixture was investigated by kinetic and equilibrium assays, taking into consideration several parameters such as initial pH, sorbent dosage and agitation speed. The results showed that the adsorption process is quite fast, reaching an 18% reduction in paraquat concentration in a very short period of time. The addition of hematite particles to kaolin suspension had no apparent effect on the maximum amount of paraquat adsorbed. Kinetic parameters were determined by fitting the pseudo-second order model to the experimental data (correlation coefficients close to 1. Isotherm studies indicate an inhibitory effect, promoted by hematite particles, that was not detected in the adsorption assays. Equilibrium data was best adjusted using the Langmuir model which yielded higher correlation coefficient values and smaller normalized standard deviations.

ADSORPTION OF GIBBERELLIC ACID ONTO NATURAL KAOLIN FROM TATAKAN, SOUTH KALIMANTAN

Directory of Open Access Journals (Sweden)

Sunardi Sunardi

2010-06-01

Full Text Available Adsorption of gibberellic acid (GA3 onto raw and purified kaolin from Tatakan, South Kalimantan was investigated in this study. Purification process was done by sedimentation to obtain relative pure kaolinite. Raw and purified kaolin samples were characterized by Fourier transformed infrared (FTIR spectroscopy and X-ray diffractometer (XRD. The adsorption process was carried out in a batch system and the effect of pH, contact time and GA3 concentration were experimentally studied to evaluate the adsorption capacity. The amount of GA3 adsorbed was determined by UV spectrophotometer. The result showed that the raw kaolin from South Kalimantan consist of 53.36% kaolinite, 29.47% halloysite, 4.47% chlorite, 11.32% quartz and 1.38% christobalite and the purified kaolin consist of 73.03% kaolinite, 22.6% halloysite, 0.77% chlorite, 1.37% quartz and 2.23% christobalite Adsorption experimental indicate that the optimum adsorption took place at pH 7 and contact time for 4 h. Adsorption of GA3 was described by the Langmuir adsorption isotherm model with adsorption capacity of 8.91 mg/g on raw kaolin and 10.38 mg/g on purified kaolin.   Keywords: kaolin, gibberellic acid, adsorption

Bio-beneficiation of kaolin and feldspar and its effect on fired

Indian Academy of Sciences (India)

Presence of iron compounds as impurities in kaolin and feldspar, impart reddish colour to ceramic products manufactured using these minerals. The quality of kaolin and feldspar was enriched mainly through iron removal by biological methods. Bacteria isolated from kaolin of Indian origin were used for bioleaching.

Bauxite and Kaolin Deposits of the Irwinton district, Georgia

Science.gov (United States)

Lang, Walter B.; Warren, Walter C.; Thompson, Raymond M.; Overstreet, Elizabeth F.

1965-01-01

The Irwinton district is in the central part of Georgia at the inner margin of the Coastal Plain province. The oldest rocks exposed in the district are crystalline rocks of the Piedmont province. They are unconformably overlain by nonmarine sedimentary strata of Late Cretaceous age, including gravel, micaceous sand, and lenses of kaolin. Bauxite has been found in a few of the kaolin lenses near the top of the sequence of these strata. During a long period prior to deposition of the over- lying marine beds of the Claiborne and Jackson Groups (middle and upper Eocene), the Upper Cretaceous strata were subjected to subaerial erosion. The bauxite deposits are considered to have formed during this period. They range in thickness from a few inches to more than 10 feet and occupy areas ranging from a few square feet to more than 5 acres. Most of the known bauxite deposits lie along the valleys of Commissioners Creek and Big Sandy Creek in Wilkinson County. The kaolin lenses are much larger than the bauxite deposits; some of the lenses underlie more than 200 acres and are more than 20 feet thick. Bauxite was discovered in the district in 1907 and was mined from 1910 to 1928. A few additional carloads of ore were shipped in 1941 and 1942, but no ore has been mined since that time. Reserves of high-grade bauxite are very small. Reserves of all grades of bauxite plus bauxitic clay may be about 400,000 long tons. The Irwinton district is the principal source of high-grade kaolin in the United States. The presence of kaolin here has been known since early colo- nial time, and it has been mined continuously since 1897. Production in 1959 was 1,940,279 short tons. The reserves of kaolin are very large but have never been adequately measured. Reserves of first and second grade kaolin may be 67 to 84 million short tons. Kaolin of lower grade is present in larger quantity.

Removal of Phenol in Aqueous Solution Using Kaolin Mineral Clay

International Nuclear Information System (INIS)

Sayed, M.S.

2008-01-01

Kaolin clay were tested for phenol removal as toxic liquid waste from aqueous waste water. Several experimental conditions such as weight and particle size of clay were investigated to study batch kinetic techniques, also the ph and concentration of the phenol solution were carried out. The stability of the Langmuir adsorption model of the equilibrium data were studied for phenol sorbent clay system. Infrared spectra, thermogravimetric and differential thermal analysis techniques were used to characterize the behavior of kaolin clay and kaolin clay saturated with phenol. The results obtained showed that kaolin clay could be used successfully as an efficient sorbent material to remove phenol from aqueous solution

Shear Strength of Stabilized Kaolin Soil Using Liquid Polymer

Science.gov (United States)

Azhar, A. T. S.; Fazlina, M. I. S.; Nizam, Z. M.; Fairus, Y. M.; Hakimi, M. N. A.; Riduan, Y.; Faizal, P.

2017-08-01

The purpose of this research is to investigate the suitability of polymer in soil stabilization by examining its strength to withstand compressive strength. Throughout this research study, manufactured polymer was used as a chemical liquid soil stabilizer. The liquid polymer was diluted using a proposed dilution factor of 1 : 3 (1 part polymer: 3 parts distilled water) to preserve the workability of the polymer in kaolin mixture. A mold with a diameter of 50 mm and a height of 100 mm was prepared. Kaolin soil was mixed with different percentages of polymer from 10%, 15%, 20%, 25%, 30% and 35% of the mass of the kaolin clay sample. Kaolin mixtures were tested after a curing period of 3 days, 7 days, 14 days and 28 days respectively. The physical properties were determined by conducting a moisture content test and Atterberg limit test which comprise of liquid limit, plastic limit and shrinkage limit. Meanwhile, the mechanical properties of the soil shear strength were identified through an unconfined compressive strength (UCS) test. Stabilized kaolin soil showed the highest compressive strength value when it was mixed with 35% of polymer compared to other percentages that marked an increment in strength which are 45.72% (3 days), 67.57% (7 days), 81.73% (14 days) and 77.84% (28 days). Hence, the most effective percentage of liquid polymer which should be used to increase the strength of kaolin soil is 35%.

Contemporary technology of enrichment of kaolins of Angren deposit. II. Removal of impurities and whitening of kaolins: using electrophysical and chemical methods of cleaning

International Nuclear Information System (INIS)

Krivorotov, V.F.; Usmanov, ZH.M.; Fridman, A.A.

2012-01-01

The contemporary methods of enrichment of Angren kaolins have been described. The electrophoresis and chemical whitening are demonstrated to be the most effective methods of scavenging. Application of ultrasonic dispersion, electrophoresis and chemical whitening methods allows one to obtain kaolin with whiteness ≅ 88% and content of iron oxides ≅ 0.4%. Using such kaolin as a sorbent at de coloration of plant oil have been shown good adsorption properties, meeting the level of world-wide standards for such class of materials. (authors)

Adsorption characteristics of brilliant green dye on kaolin

International Nuclear Information System (INIS)

Nandi, B.K.; Goswami, A.; Purkait, M.K.

2009-01-01

Experimental investigations were carried out to adsorb toxic brilliant green dye from aqueous medium using kaolin as an adsorbent. Characterization of kaolin is done by measuring: (i) particle size distribution using particle size analyzer, (ii) BET surface area using BET surface analyzer, and (iii) structural analysis using X-ray diffractometer. The effects of initial dye concentration, contact time, kaolin dose, stirring speed, pH and temperature were studied for the adsorption of brilliant green in batch mode. Adsorption experiments indicate that the extent of adsorption is strongly dependent on pH of solution. Free energy of adsorption (ΔG 0 ), enthalpy (ΔH 0 ) and entropy (ΔS 0 ) changes are calculated to know the nature of adsorption. The calculated values of ΔG 0 at 299 K and 323 K indicate that the adsorption process is spontaneous. The estimated values of ΔH 0 and ΔS 0 both show the negative sign, which indicate that the adsorption process is exothermic and the dye molecules are organized on the kaolin surface in less randomly fashion than in solution. The adsorption kinetic has been described by first-order, pseudo-second-order and intra-particle-diffusion models. It was observed that the rate of dye adsorption follows pseudo-second-order model for the dye concentration range studied in the present case. Standard adsorption isotherms were used to fit the experimental equilibrium data. It was found that the adsorption of brilliant green on kaolin follows the Langmuir adsorption isotherm

Assembling strategy to synthesize palladium modified kaolin nanocomposites with different morphologies

Science.gov (United States)

Li, Xiaoyu; Ouyang, Jing; Zhou, Yonghua; Yang, Huaming

2015-09-01

Nanocomposites of aluminosilicate minerals, kaolins (kaolinite and halloysite) with natural different morphologies assembling with palladium (Pd) nanoparticles have been successfully synthesized through strong electrostatic adsorption and chemical bonding after surface modification with 3-aminopropyl triethoxysilane (APTES). Meanwhile, the influence of different morphologies supports on catalytic hydrogenation properties was explored. The surface concentration of amino groups on the kaolins was related to the morphology and surface nature. Electronmicroscopy revealed that the monodisperse Pd nanoparticles were uniformly deposited onto the surface of kaolins, ranging in diameter from 0.5 nm to 5.5 nm. The functional groups could not only improve the dispersion of kaolins with different morphologies in solution, but also enhance the interaction between Pd precursors and kaolins, thus preventing small Pd nanoparticles from agglomerating and leading to high activity for the catalytic hydrogenation of styrene. Pd-FK@APTES was more active compared to other samples. Selecting the kaolin morphology with a different surface nature allows the selective surface modification of a larger fraction of the reactive facets on which the active sites can be enriched and tuned. This desirable surface coordination of catalytically active atoms could substantially improve catalytic activity.

Structure and properties of pregelatinized cassava starch/kaolin composites

International Nuclear Information System (INIS)

Kaewtatip, Kaewta; Tanrattanakul, Varaporn

2012-01-01

Highlights: ► Pregelatinized starch/kaolin composites were prepared using compression molding. ► The tensile strengths of the composites were higher than for thermoplastic starch. ► Degradation temperatures of the composites were higher than for thermoplastic starch. ► The retrogradation behavior of the composites was hindered by kaolin. -- Abstract: Pregelatinized cassava starch/kaolin composites were prepared using compression molding. The morphology of the fractured surfaces, retrogradation behavior, thermal decomposition temperatures and mechanical properties of the composites were investigated using scanning election microscopy (SEM), X-ray diffraction (XRD), thermal gravimetric analysis (TGA) and tensile testing, respectively. The tensile strengths and thermal degradation temperatures of the composites were higher than for thermoplastic starch (TPS). The retrogradation behavior of the composites was hindered by kaolin. The water absorption was measured after aging for 12 and 45 days at a relative humidity (RH) of 15% and 55%. It indicated that all the composites displayed lower water absorption values than TPS.

Preparation of Modified Kaolin Filler with Cesium and Its Application in Security Paper

Directory of Open Access Journals (Sweden)

Houssni El-Saied

2013-01-01

Full Text Available In this study, cesium was added intentionally during paper manufacture for protecting the papers against forgery and counterfeiting by sorbing cesium ions (Cs+ on kaolin, used as special filler in papermaking. The sorption of cesium from aqueous solution by kaolin was studied as a function of pH, shaking time, cesium initial concentration, and mass of kaolin using batch technique. The results showed that a solution containing 10 mg/L Cs+ and 250 mg of kaolin at pH 6 can be used to modify the kaolin. Paper handsheets were prepared containing various percentages of the modified kaolin. The mechanical and optical properties of paper handsheets were studied. The prepared paper handsheets were irradiated by gamma irradiation using different doses. Fourier transform infrared (FTIR spectroscopy was used to study the effect of kaolin modification by cesium and gamma irradiation on paper handsheets properties. The results indicated that modified kaolin enhanced the mechanical and optical properties of paper handsheets. Electron spin resonance (ESR spectroscopy and laser-induced breakdown spectroscopy (LIBS were also used. They provided rapid, sensitive and nondestructive techniques in differentiating between different questioned documents. This study presents a new concept in manufacturing security papers and anticounterfeiting applications.

Mussel inspired preparation of amine-functionalized Kaolin for effective removal of heavy metal ions

Energy Technology Data Exchange (ETDEWEB)

Huang, Qiang; Liu, Meiying; Deng, Fengjie [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang, 330031 (China); Wang, Ke [Department of Chemistry and the Tsinghua Center for Frontier Polymer Research, Tsinghua University, Beijing, 100084 (China); Huang, Hongye; Xu, Dazhuang; Zeng, Guangjian [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang, 330031 (China); Zhang, Xiaoyong, E-mail: xiaoyongzhang1980@gmail.com [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang, 330031 (China); Wei, Yen [Department of Chemistry and the Tsinghua Center for Frontier Polymer Research, Tsinghua University, Beijing, 100084 (China)

2016-09-15

Adsorption has been well regarded as a promising and efficient method for the removal of low concentration heavy metal ions in aqueous solutions. And kaolin has been considered as a kind of low cost and environment-friendly adsorbent for its abundant in nature. But the low adsorption capacity to heavy metal ions and severe aggregation in solution restrains its application. In this work, an environment-friendly adsorbent (denoted as Kaolin-PDA-PEI) was prepared based on mussel inspired chemistry and Michael addition reaction between high reaction activity of polydopamine (PDA) and polyethyleneimine (PEI), which was possesses a number of amine groups. The amine groups have displayed strong adsorption affinity towards copper ions. The successful modification of Kaolin by PDA and PEI was confirmed by a series of analyses, such as Fourier transform infrared spectroscopy, transmission electron microscopy, thermal gravimetry analysis and X-ray photoelectron spectroscopy. The effects of various parameters such as contact time, pH, initial concentrations of copper ions and temperature on copper ion adsorption by Kaolin-PDA-PEI were investigated. Kaolin-PDA-PEI shows higher adsorption capacity as compared with the raw Kaolin. The kinetic adsorption data were analyzed using pseudo-first-order, pseudo-second-order and intraparticle diffusion model. The Langmuir isotherm and Freundlich isotherm equilibrium model were applied to adsorption isotherm data to find the better fit isotherm. The results showed that adsorption process was well fitted by Langmuir isotherm model. The values of thermodynamics constants such as entropy change (ΔS{sup 0}), enthalpy change (ΔH{sup 0}) and Gibbs free energy (ΔG{sup 0}) were also calculated. The results indicated that the adsorption process of Kaolin-PDA-PEI were endothermic and spontaneous. - Graphical abstract: Amino groups functionalized Kaolin was facilely prepared via mussel inspired chemistry. The modified Kaolin exhibited much

Mussel inspired preparation of amine-functionalized Kaolin for effective removal of heavy metal ions

International Nuclear Information System (INIS)

Huang, Qiang; Liu, Meiying; Deng, Fengjie; Wang, Ke; Huang, Hongye; Xu, Dazhuang; Zeng, Guangjian; Zhang, Xiaoyong; Wei, Yen

2016-01-01

Adsorption has been well regarded as a promising and efficient method for the removal of low concentration heavy metal ions in aqueous solutions. And kaolin has been considered as a kind of low cost and environment-friendly adsorbent for its abundant in nature. But the low adsorption capacity to heavy metal ions and severe aggregation in solution restrains its application. In this work, an environment-friendly adsorbent (denoted as Kaolin-PDA-PEI) was prepared based on mussel inspired chemistry and Michael addition reaction between high reaction activity of polydopamine (PDA) and polyethyleneimine (PEI), which was possesses a number of amine groups. The amine groups have displayed strong adsorption affinity towards copper ions. The successful modification of Kaolin by PDA and PEI was confirmed by a series of analyses, such as Fourier transform infrared spectroscopy, transmission electron microscopy, thermal gravimetry analysis and X-ray photoelectron spectroscopy. The effects of various parameters such as contact time, pH, initial concentrations of copper ions and temperature on copper ion adsorption by Kaolin-PDA-PEI were investigated. Kaolin-PDA-PEI shows higher adsorption capacity as compared with the raw Kaolin. The kinetic adsorption data were analyzed using pseudo-first-order, pseudo-second-order and intraparticle diffusion model. The Langmuir isotherm and Freundlich isotherm equilibrium model were applied to adsorption isotherm data to find the better fit isotherm. The results showed that adsorption process was well fitted by Langmuir isotherm model. The values of thermodynamics constants such as entropy change (ΔS"0), enthalpy change (ΔH"0) and Gibbs free energy (ΔG"0) were also calculated. The results indicated that the adsorption process of Kaolin-PDA-PEI were endothermic and spontaneous. - Graphical abstract: Amino groups functionalized Kaolin was facilely prepared via mussel inspired chemistry. The modified Kaolin exhibited much enhanced adsorption

Synthesis of microporous material faujasite-type from kaolin waste

International Nuclear Information System (INIS)

Hildebrando, E.A.; Valenzuela-Diaz, F.R.; Angelica, R.S.; Neves, R.F.

2010-01-01

Zeolite with structure faujasite was synthesized using kaolin waste from kaolin processing industries for paper coating as predominant source of silicon and aluminum; the starting material was characterized by XRF, XRD, DTA/TG, SEM, and products obtained by XRD and SEM. Synthesis in hydrothermal conditions occurred on autoclave and time-temperature effects, as well as the relationship Si/Al were considered. The results show that the methodology developed with the waste of calcined kaolin reacting at 90 deg C for 20 hours in an alkaline medium, in the presence of an additional source of silica was obtained zeolite Y as single phase present in the product. (author)

Synthesis and characterization of kaolin with polystyrene via in-situ polymerization and their application on polypropylene

International Nuclear Information System (INIS)

Zhao, Songfang; Qiu, Shangchang; Zheng, Yuying; Cheng, Lei; Guo, Yong

2011-01-01

To improve both the mechanical and thermal properties of kaolin/polypropylene (PP) composites, kaolin was modified by using 3-(trimethoxysilyl) propylmethacrylate (YDH-570) as a coupling agent to form polymerizable particle. Styrene was radically polymerized through the immobilized vinyl using benzoyl peroxide (BPO) as an initiator. Fourier transform-infrared (FTIR) spectroscopy, particle size distribution, X-ray diffraction (XRD) and thermo-gravimetric analysis (TGA) well demonstrated that the kaolin-polystyrene particles were successfully synthesized via in-situ polymerization. While the modified kaolin and raw kaolin were introduced into the PP matrix, it could be concluded that modified kaolin/PP composites have better mechanical and thermal properties than raw kaolin/PP composites, and these improvements were attributed to the desirable dispersion of kaolin in PP matrix.

Use of airborne gamma-ray spectrometry for kaolin exploration

Science.gov (United States)

Tourlière, B.; Perrin, J.; Le Berre, P.; Pasquet, J. F.

2003-08-01

Airborne gamma-ray spectrometry was used to define targets with kaolin potential in the Armorican Massif of Brittany, France. This exploration method is based on the principle that kaolinite, an aluminosilicate clay mineral constituting kaolin, is formed by the hydrolysis of potash feldspar with the elimination of potassium. Therefore, potassium contrast between favourable host-rock such as a leucogranite and kaolin occurrence is likely a significant pathfinder. As the relationship between the potassium-40 recorded by an airborne gamma-ray spectrometer and total potassium is constant, such data provide us a direct measurement of the potassium content of the ground flown over. Our study tested this by calculating, for each geological unit, the difference between the measured and average potassium content calculated for a given geological formation. The study was based on (i) a recent (1998) high-definition airborne geophysical survey over the Armorican Massif undertaken on behalf of the French Government, and (ii) new geological compilation maps covering the same region. Depleted zones, where the measured potassium is less than the average potassium content calculated target areas with high potential of containing kaolin, provided that the unit was originally rich in potash feldspar. By applying this method to the entire Armorican Massif, it was possible to identify 150 potassium-depleted zones, including 115 that were subjected to rapid field checks and 36 that contained kaolin (21 new discoveries). This method, which is both safe for the environment and easy to use, is therefore a good tool for rapidly defining targets with kaolin potential at a regional scale. The method may also have possibilities in exploring for other types of deposit characterised by an enrichment or depletion in U, K and/or Th.

Surface modification of calcined kaolin with toluene diisocyanate based on high energy ball milling

International Nuclear Information System (INIS)

Yuan, Yongbing; Chen, Hongling; Lin, Jinbin; Ji, Yan

2013-01-01

The surface of calcined kaolin particle was modified with toluene diisocyanate (TDI) by using high energy ball milling. The prepared hybrids were characterized by FT-IR, MAS NMR, thermal analysis (TGA-DSC), static water contact angle (CA), apparent viscosity and transmission electron microscopy (TEM). FT-IR and MAS NMR spectra demonstrated that TDI molecules were chemically anchored to kaolin surface after modification. The results of thermal analysis showed that the maximum grafting ratio reached up to 446.61% when the mass ratio of TDI/kaolin was 0.5:1.0, and CA measurements revealed that the resultant hybrids exhibited strong hydrophobicity (148.82°). Apparent viscosity and TEM were employed to examine the dispersion properties of blank and modified kaolin particles in poly (dimenthylsiloxane) matrix. The results illustrated that the dispersion stability depended strongly on the grafting ratio of TDI, neither too low nor too high achieved uniform and stable dispersion, and the favorable grafting ratio was obtained when the mass ratio of TDI/kaolin was 0.2:1.0. Further modification of TDI/kaolin (mass ration of TDI/kaolin, 1.0:1.0) particles with bis(aminopropyl)-terminated-poly(dimethylsiloxane) (APS) was also investigated. TEM evidenced that the dispersion properties of the obtained TDI/APS/kaolin particles were remarkably improved in octamethyl cyclotetrasiloxane compared with the original TDI/kaolin particles.

Surface modification of calcined kaolin with toluene diisocyanate based on high energy ball milling

Energy Technology Data Exchange (ETDEWEB)

Yuan, Yongbing; Chen, Hongling, E-mail: hlchen@njut.edu.cn; Lin, Jinbin; Ji, Yan

2013-11-01

The surface of calcined kaolin particle was modified with toluene diisocyanate (TDI) by using high energy ball milling. The prepared hybrids were characterized by FT-IR, MAS NMR, thermal analysis (TGA-DSC), static water contact angle (CA), apparent viscosity and transmission electron microscopy (TEM). FT-IR and MAS NMR spectra demonstrated that TDI molecules were chemically anchored to kaolin surface after modification. The results of thermal analysis showed that the maximum grafting ratio reached up to 446.61% when the mass ratio of TDI/kaolin was 0.5:1.0, and CA measurements revealed that the resultant hybrids exhibited strong hydrophobicity (148.82°). Apparent viscosity and TEM were employed to examine the dispersion properties of blank and modified kaolin particles in poly (dimenthylsiloxane) matrix. The results illustrated that the dispersion stability depended strongly on the grafting ratio of TDI, neither too low nor too high achieved uniform and stable dispersion, and the favorable grafting ratio was obtained when the mass ratio of TDI/kaolin was 0.2:1.0. Further modification of TDI/kaolin (mass ration of TDI/kaolin, 1.0:1.0) particles with bis(aminopropyl)-terminated-poly(dimethylsiloxane) (APS) was also investigated. TEM evidenced that the dispersion properties of the obtained TDI/APS/kaolin particles were remarkably improved in octamethyl cyclotetrasiloxane compared with the original TDI/kaolin particles.

1.7.2. The hydrochloric acid decomposition of pre-baked kaolin clays and siallites

International Nuclear Information System (INIS)

Mirsaidov, U.M.; Mirzoev, D.Kh.; Boboev, Kh.E.

2016-01-01

Present article of book is devoted to hydrochloric acid decomposition of pre-baked kaolin clays and siallites. The chemical composition of kaolin clays and siallites was determined. The influence of temperature, process duration, acid concentration on hydrochloric acid decomposition of pre-baked kaolin clays and siallites was studied. The optimal conditions of hydrochloric acid decomposition of pre-baked kaolin clays and siallites were determined.

Electrical Properties of Zinc-Kaolin Composites below its Percolation ...

African Journals Online (AJOL)

In this paper, we present some electrical properties of the zinc-kaolin cermet resistors with zinc metal fillers below the percolation threshold. Rectangular cermet rods of dimensions 65 mm by 6.5 mm by 3.2 mm were produced in a mould with semi-dry the zinc/kaolin powder mixture which is compressed with a force of about ...

Processed kaolin affects the probing and settling behavior of Diaphorina citri (Hemiptera: Lividae).

Science.gov (United States)

Miranda, Marcelo P; Zanardi, Odimar Z; Tomaseto, Arthur F; Volpe, Haroldo Xl; Garcia, Rafael B; Prado, Ernesto

2018-03-05

Alternative methods that have the potential to reduce the entry of Diaphorina citri Kuwayama (Hemiptera: Liviidae), the major citrus pest worldwide, into commercial groves could be a viable approach for huanglongbing management. Kaolin is an aluminum silicate that when sprayed on plants forms a white particle film that interferes with host recognition by the insects. Diaphorina citri orients towards the host plants by visual and olfactory cues. The purpose of the study was to determine the effect of processed kaolin on D. citri settling (no-choice) and probing behavior [electrical penetration graph (EPG) technique] under laboratory conditions, and to study its host plant finding ability and dispersal under field conditions in the absence and presence of young shoots. Under laboratory conditions, kaolin caused an overall reduction of 40% in the number of psyllids settled on treated seedlings; furthermore, the proportion of individuals that were able to reach the phloem was 50% lower on kaolin-treated plants than on untreated plants. In the field, the plant finding ability of D. citri was disrupted on kaolin-treated trees (overall reduction of 96%), regardless of the vegetative condition, and psyllid dispersal was slower in kaolin-treated plots than in the untreated control. This study clearly demonstrates that processed kaolin interferes negatively with different aspects of the host plant finding ability of D. citri. These findings suggest that processed kaolin has a high potential to reduce huanglongbing primary infection. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Technological properties of kaolin from Para; Propriedades tecnologicas do caulin do Para

Energy Technology Data Exchange (ETDEWEB)

Hildebrando, E.; Martin-Cortes, G.R.; Esper, F.J.; Wiebeck, H.; Alves Junior, P.; Valenzuela-Diaz, F.R., E-mail: germac@usp.br [Universidade de Sao Paulo (PMT/EP/USP), Sao Paulo, SP (Brazil). Escola Politecnica. Departamento de Engenharia Metalurgica e de Materiais

2011-07-01

The NE of the State of Para, is notable for its large reserves of kaolin for paper. Kaolin is a mineral composed of hydrated aluminum silicates such as kaolinite and halloysite. The exploitation of these reserves to generate products with higher commercial value, especially in the industries of adsorbents and catalysts, is what motivates the continuous study of technological properties of the Amazon kaolin's. Thus, this paper presents a technological characterization of a sample of kaolin from Para State by X-ray diffraction, SEM - scanning electron microscopy and infrared spectroscopy. The results of preliminary tests indicate that the sample consists for the most part by kaolinite present in low concentrations of quartz and anatase. (author)

A Study on Kaolin and Titanium dioxide affecting Physical Properties of Electrocoating

International Nuclear Information System (INIS)

Yang, Wonseog; Hwang, Woonsuk

2013-01-01

The electrocoating for automotive bodies is pigmented with a mixture of titanium dioxide and kaolin. In this study, the effects of titanium dioxide and kaolin contents in coating on electrodeposition process, drying, and surface properties such as surface roughness, gloss, impact resistance and corrosion resistance were investigated. Titanium dioxide and kaolin in coating do not have a decisive effect on curing reaction during drying and corrosion resistance but on gloss, surface roughness, impact resistance and electrodeposition process of coating. According to its size and shape on coating surface, pigment contents increased during drying process. However, the contents of kaolin and TiO 2 in coating didn't affect the corrosion resistance on zinc phosphated substrate, and the curing properties

The contribution of lateritization processes to the formation of the kaolin deposits from eastern Amazon

Science.gov (United States)

da Costa, Marcondes Lima; Sousa, Daniel José Lima; Angélica, Rômulo Simões

The eastern region of the Amazon is home to the most important kaolin bauxite producing district in Brazil, referred to as the Paragominas-Capim kaolin bauxite district, which has a reserve of at least 1.0 billion tons of high-quality kaolin used in the paper coating industry. The kaolin deposits are closely related to sedimentary rocks of the Parnaíba basin and their lateritic cover. Two large deposits are already being mined: IRCC (Ipixuna) and PPSA (Paragominas). The geology of the IRCC mine is comprised of the kaolin-bearing lower unit (truncated mature laterite succession derived from the Ipixuna/Itapecuru formation) and the upper unit (immature lateritized Barreiras formation). The lower kaolin unit is characterized by a sandy facies at the bottom and a soft (ore) with flint facies at the top. It is formed by kaolinite, quartz, some iron oxi-hydroxides, mica and several accessories and heavy minerals. The mangrove covering; and immature lateritization - partial kaolin ferruginization during the Pleistocene.

Potassium Capture by Kaolin, Part 1: KOH

DEFF Research Database (Denmark)

Wang, Guoliang; Jensen, Peter Arendt; Wu, Hao

2018-01-01

-capture level. The effect of reaction temperature,K-concentration in the flue gas, and, thereby, molar ratio of K/(Al+Si) in reactants, gas residence time, and solid particle size on K-capture reaction was systematically investigated. Corresponding equilibrium calculations were conducted with FactSage 7.......0. The experimental results showed that kaolin reached almost full conversion to K-aluminosilicates under suspension-fired conditions at 1100–1450 °C for a residence time of 1.2 s and a particle size of D50 = 5.47 μm. The amount of potassium captured by kaolin generally followed the equilibrium at temperatures above...

Mineralogical characteristics of Cretaceous-Tertiary kaolins of the Douala Sub-Basin, Cameroon

Science.gov (United States)

Bukalo, Nenita N.; Ekosse, Georges-Ivo E.; Odiyo, John O.; Ogola, Jason S.

2018-05-01

As a step in evaluating the quality of Cretaceous-Tertiary kaolins of the Douala Sub-Basin, their mineralogical characteristics were determined. The X-ray diffractometry technique was used to identify and quantify the mineral phases present in bulk and smectite > illite, with mean values of 33.01 > 11.20 > 4.41 wt %; and 72.23 > 10.69 > 4.69 wt %, in bulk and <2 μm fractions, respectively. The kaolins, micromorphologically, consisted of pseudo-hexagonal and thin platy particles; swirl-textured particles; and books or stacks of kaolinite particles. Three main reactions occurred during heating of the kaolins: a low temperature endothermic reaction, observed between 48 and 109 °C; a second low temperature peak, observed between 223 and 285 °C; and a third endothermic peak was found between 469 and 531 °C. In addition, an exothermic reaction also occurred between 943 and 988 °C in some of the samples. The absence of primary minerals such as feldspars and micas in most of these kaolins is an indication of intensive weathering, probably due to the humid tropical climate of the region. The different morphologies suggested that these kaolins might have been transported. Therefore, a humid tropical climate was responsible for the formation of Cretaceous-Tertiary kaolins of the Douala Sub-Basin through intense weathering of surrounding volcanic and metamorphic rocks.

Mineralogical variation in the size fractions of a Ranong kaolin, southern Thailand

Science.gov (United States)

Pisutha-Arnond, Visut; Phuvichit, Suraphol; Leepowpanth, Quanchai

A representative crude Ranong kaolin from the Thungkla-Ranong mine was separated into > 2 mm (granule), 2-1 mm (very coarse sand), 1-0.5 mm (coarse sand), 0.5-0.25 mm (medium sand), 0.25-0.125 mm (fine sand), 0.125-0.062 mm (very fine sand) and 62-28, 28-14, 17-7, 7-4, 4-2, 2-1 and dispersive X-ray spectrometer (EDX). Kaolin group minerals were differentiated by using XRD in combination with various chemical and heat treatments together with TEM, SEM and DTA. The Ranong kaolin consists predominantly of tubular halloysite, poorly crystallized kaolinite and quartz with minor amounts of mica and K-feldspars. Other trace constituents include gibbsite, tourmaline, zircon and colored impurities (i.e. extractable iron hydroxide coating on clay mineral surface). The kaolin minerals are found in all size fractions by which their contents and halloysite/kaolinite ratios increase as the particle sizes become finer. Quartz and mica are also detected in almost all size fractions. They are, however, more abundant with coarsening particle size. Gibbsite, K-feldspar and tourmaline are mainly concentrated in the fine sand to silt size fractions. Crystallinity of kaolin minerals as measured by XRD varied moderately with size. Relatively pure kaolin minerals, predominantly halloysite and kaolinite, can be obtained in the particle size below 1 or 2 μm.

Synthesis and characterization of mesoporous NaY zeolite from natural Blitar’s kaolin

Science.gov (United States)

Khalifah, S. N.; aini, Z. N.; Hayati, E. K.; Aini, N.; Prasetyo, A.

2018-03-01

Mesoporous NaY Zeolite has been synthesized from calcined natural Blitar’s kaolin with the addition of NaOH and CTABr surfactant as mesoporous template by hydrothermal method. Natural kaolin was calcinated with different time and temperature to change kaolin to metakaolin. X-ray diffraction data showed that mesoporous NaY zeolite was formed with impurities compound of sodalite, kaolin and quartz phases. The BET analysis resulted that the pore of NaY Zeolite belongs to mesoporous type with pore size 9,421 nm. Characterization from FTIR confirmed about the functional group of zeolites (988, 776, 663, 464 cm-1). Scanning electron microscopy characterization showed that the morphological of mesoporous NaY zeolites have uniform and crystalline particles formed.

Kaolin modulates ABA and IAA dynamics and physiology of grapevine under Mediterranean summer stress.

Science.gov (United States)

Dinis, L-T; Bernardo, S; Luzio, A; Pinto, G; Meijón, M; Pintó-Marijuan, M; Cotado, A; Correia, C; Moutinho-Pereira, J

2018-01-01

The foliar exogenous application of kaolin, a radiation-reflecting inert mineral, has proven to be an effective short-term climate change mitigation strategy for Mediterranean vineyards. In this work, we address the hypothesis that kaolin could improve both the hormonal dynamics and physiological responses of grapevines growing in Douro Region, northern Portugal. For this purpose, the leaf water potential, gas exchange and chlorophyll a fluorescence parameters were monitored, as well as the abscisic acid (ABA) and indole-3-acetic acid (IAA) quantification and immunolocalization were assessed. The study revealed a slight decrease in ABA and an increase in IAA in the kaolin treatment, which in turn were associated with the improvement of physiological performance. A month after spraying, kaolin improves the water potential respectively, 30% and 17% in the predawn and midday periods. Besides, plants treated with kaolin showed higher values of stomatal conductance, net CO 2 assimilation rate and intrinsic water use efficiency. Kaolin also ameliorates the effective PSII efficiency (67%), as well as the maximum quantum efficiency of photosystem II and the photosynthetic electron transport rate (>73%). These results were consistent with the higher photochemical quenching and the lower non-photochemical quenching observed in treated leaves and with the better performance obtained by the JIP test parameters. Physiological and hormonal analysis confirmed that kaolin effectively enhance grapevine summer stress tolerance. Copyright © 2017 Elsevier GmbH. All rights reserved.

Use of kaolin waste for production os soil-lime blocks

International Nuclear Information System (INIS)

Anjos, C.M. dos; Neves, G.A.

2011-01-01

There is an evident growth in waste generation over the last decades, especially in developing countries. The mining industry produces large quantities and different kinds and levels of dangerousness, such as the kaolin processing industry, which produces waste based on silica, mica and kaolinite. Disposal of this material in an inappropriate location causes significant environmental impacts, which could be minimized with the use of waste as raw material for use in construction. This paper has as main objective to study the incorporation of the kaolin processing waste into soil-lime. The residues of kaolin were calcined at a temperature of 800 ° C for evaluation of pozzolanic activity. Raw materials and conventional alternatives were characterized by means of test particle size analysis by laser diffraction, chemical analysis, X-ray diffraction. Then, blocks conventional soil-lime and soil-lime with the introduction of residual kaolin in proportions of 10%, 20%, 30% and 40% were cast and cured in a moist chamber for periods of 28, 60 and 90 days. The technological tests of compressive strength results obtained within the specifications of the ABNT. The best results were for 90 days of healing and 20% residue. (author)

Statistical treatment of bleaching kaolin by iron removal

Energy Technology Data Exchange (ETDEWEB)

Hernandez H, R. A.; Legorreta G, F.; Hernandez C, L. E. [Universidad Autonoma del Estado de Hidalgo, Area Academica de Ciencias de la Tierra y Materiales, Carretera Pachuca-Tulancingo Km 4.5, Mineral de la Reforma, 42184 Hidalgo (Mexico); Martinez L, A., E-mail: angelitofox3@hotmail.com [Universidad Autonoma de Coahuila, Blvd. V. Carranza y Gonzalez Lobo s/n, 25280 Saltillo, Coahuila (Mexico)

2013-07-01

In the present study, oxalic acid was used as a leaching reagent to remove iron from a kaolin mineral. Statistical analysis was conducted to determine the most influential factors in the dissolution of iron from the kaolin mineral. Our goal was ferric iron solubilization and its reduction to ferrous iron to improve the iron removal in the acid medium. Leaching experiments were conducted at atmospheric pressure. A two-level factorial design of the type 2{sup 4} was utilized. The dependent variable was the percentage of dissolved iron, and the dependent variables in this study were acid concentration (0.35 and 0.50 M), temperature (75 C and 100 C), leaching time (2 and 4 h), and ph (1.5 and 2.5). An analysis of variance revealed that the effects of the factors temperature (b), ph (d), and the combined effects of temperature and time (b c) resulted in the maximum dissolution of iron of 88% at 100 C, giving a kaolin mineral with a whiteness index 93.50. For the mineralogical analysis the X-ray diffraction technique was used. (Author)

Statistical treatment of bleaching kaolin by iron removal

International Nuclear Information System (INIS)

Hernandez H, R. A.; Legorreta G, F.; Hernandez C, L. E.; Martinez L, A.

2013-01-01

In the present study, oxalic acid was used as a leaching reagent to remove iron from a kaolin mineral. Statistical analysis was conducted to determine the most influential factors in the dissolution of iron from the kaolin mineral. Our goal was ferric iron solubilization and its reduction to ferrous iron to improve the iron removal in the acid medium. Leaching experiments were conducted at atmospheric pressure. A two-level factorial design of the type 2 4 was utilized. The dependent variable was the percentage of dissolved iron, and the dependent variables in this study were acid concentration (0.35 and 0.50 M), temperature (75 C and 100 C), leaching time (2 and 4 h), and ph (1.5 and 2.5). An analysis of variance revealed that the effects of the factors temperature (b), ph (d), and the combined effects of temperature and time (b c) resulted in the maximum dissolution of iron of 88% at 100 C, giving a kaolin mineral with a whiteness index 93.50. For the mineralogical analysis the X-ray diffraction technique was used. (Author)

Influence of Sulfonated-Kaolin On Cationic Exchange Capacity Swelling Degree and Morphology of Chitosan/Kaolin Composites

Directory of Open Access Journals (Sweden)

Ozi Adi Saputra

2016-06-01

Full Text Available Preparation of sulfonated-kaolin (sKao has been conducted and used as filler on chitosan matrix via solution casting method, namely chitosan/sKao (Cs/sKao. Swelling degree, cationic exchange capacity and thermal stability were evaluated to determine chitosan/sKao membranes performance as proton exchange membrane in fuel cell. Functional group analysis of chitosan, sKao and synthesized products were studied using Fourier Transform Infra-Red (FTIR spectroscopy. In this study, swelling degree and swelling area of Cs/sKao are also studied to determine of membrane ability to swelling which compare to unmodified chitosan/kaolin (Cs/Kao. The presence of sKao in chitosan matrix was able to improve cationic exchange capacity (CEC which proved by morphological study of membrane surface after CEC test. Moreover, Thermal stability of Cs/sKao showed the membrane has meet requirement for PEM application.

Kaolin in the diet and its effects on performance, litter moisture and intestinal morphology of broiler chickens

Directory of Open Access Journals (Sweden)

Marina Jorge de Lemos

2015-10-01

Full Text Available The objective of this study was to evaluate the effect of the addition of kaolin in the diet on performance, litter moisture and intestinal morphology of broiler chickens. Four hundred ninety-two broiler chickens distributed in a completely randomized design with three treatments and four replicates of 41 birds each, divided into three periods (15-21; 22-34; 35-52 days were used. The following treatments were: Control - reference diet without added kaolin; treatment 1 - reference diet + 0.75% kaolin; Treatment 2 - reference diet + 1.5% kaolin. The variables analyzed were: feed intake, average weight, average weight gain, feed conversion, litter moisture, villus height and crypt depth. The inclusion of kaolin in the diet significantly reduced feed intake, increased weight and average weight gain and improved feed conversion of broilers. The litter moisture decreased significantly after the inclusion of kaolin in the diet. The height of the duodenal villi of broilers increased significantly after inclusion of kaolin, while crypt depth was not influenced. The inclusion 0.75% of kaolin in the diet improved the performance, decreased litter moisture and benefited the intestinal integrity of broilers.

Assembling strategy to synthesize palladium modified kaolin nanocomposites with different morphologies

OpenAIRE

Li, Xiaoyu; Ouyang, Jing; Zhou, Yonghua; Yang, Huaming

2015-01-01

Nanocomposites of aluminosilicate minerals, kaolins (kaolinite and halloysite) with natural different morphologies assembling with palladium (Pd) nanoparticles have been successfully synthesized through strong electrostatic adsorption and chemical bonding after surface modification with 3-aminopropyl triethoxysilane (APTES). Meanwhile, the influence of different morphologies supports on catalytic hydrogenation properties was explored. The surface concentration of amino groups on the kaolins w...

Production and Structural Investigation of Polyethylene Composites with Modified Kaolin

International Nuclear Information System (INIS)

Domka, L.; Malicka, A.; Stachowiak, N.

2008-01-01

The study was undertaken to evaluate the effect of the filler (kaolin) modification with silane coupling agents on the properties of the polyethylene (HDPE Hostalen ACP 5831) composites. Powder mineral fillers are added to polymers to modify the properties of the latter and to reduce the cost of their production. A very important factor is the filler dispersion in the polymer matrix. Kaolin modified with 3-methacryloxypropyltrimethoxysilane and pure kaolin were characterised by surface area, pore size, water absorbing capacity, paraffin oil absorbing capacity, bulk density, scanning electron microscopy observations and X-ray diffraction measurements. Their performance was characterised by determination of the mechanical resistance upon static stretching and tearing, and their structure was observed in scanning electron microscopy images. The results were compared to those obtained for the composites with unmodified filler and pure HDPE. (authors)

Production and Structural Investigation of Polyethylene Composites with Modified Kaolin

Science.gov (United States)

Domka, L.; Malicka, A.; Stachowiak, N.

2008-08-01

The study was undertaken to evaluate the effect of the filler (kaolin) modification with silane coupling agents on the properties of the polyethylene (HDPE Hostalen ACP 5831) composites. Powder mineral fillers are added to polymers to modify the properties of the latter and to reduce the cost of their production. A very important factor is the filler dispersion in the polymer matrix. Kaolin modified with 3-methacryloxypropyltrimethoxysilane and pure kaolin were characterised by surface area, pore size, water absorbing capacity, paraffin oil absorbing capacity, bulk density, scanning electron microscopy observations and X-ray diffraction measurements. Their performance was characterised by determination of the mechanical resistance upon static stretching and tearing, and their structure was observed in scanning electron microscopy images. The results were compared to those obtained for the composites with unmodified filler and pure HDPE.

Sample size clay kaolin of primary in pegmatites regions Junco Serido - PB and Equador - RN

International Nuclear Information System (INIS)

Meyer, M.F.; Sousa, J.B.M.; Sales, L.R.; Silva, P.A.S.; Lima, A.D.D.

2016-01-01

Kaolin is a clay formed mainly of kaolinite resulting from feldspar weathering or hydrothermal. This study aims to investigate the way of occurrence, kaolin particle size of the pegmatites of the Borborema Province Pegmatitic in the regions of Junco do Serido-PB and Ecuador-RN. These variables were analyzed considering granulometric intervals obtained from wet sieving of samples of pegmatite mines in the region. Kaolin was received using sieves of 200, 325, 400 and 500 mesh and the sieve fractions retained by generating statistical parameters histograms. kaolin particles are extremely fine and pass in its entirety through 500 mesh sieve. The characterization of minerals in fine fractions by diffraction of X-rays showed that the relative amount of sericite in fractions retained in sieves 400 and 500 mesh impairing the whiteness and mineralogical texture kaolin production. (author)

Monitoring of Radiation Levels in Mines of Kaolin Located in the Region Serido-PB, Brazil

International Nuclear Information System (INIS)

Guerra Spacov, Isabel Cristina; Dos Santos Amaral, Milton; Araujo dos Santos Junior, Jose

2015-01-01

Kaolin is formed mainly by kaolinite and is used in many industrial sectors. Kaolin may be associated with by-products such as quartz, mica, feldspar and sand. The background radiation from nature is very important, since it represents the main source of human exposure to radiation. In kaolin, radionuclides are present as the 40 K and series 238 U and 232 Th. This study aimed to obtain the rates of effective doses of kaolin mines in the region of Serido-PB, Brazil, where there are several productions and mineral occurrences, including kaolin and uranium at nearby areas. Four kaolin mines located in the Serido-PB region were monitored by a portable discriminator detector NaI(Ti). Measurements were obtained outdoors in triplicate, at a distance of 1.0 meters from the Earth's surface. According to the report of UNSCEAR, the world average effective dose from exposure to natural radiation sources is 2.42 mSvy -1 . the rates of effective doses identified in this study ranged from 1.37 mSvy -1 , and provided the construction of isodose curves. The highest dose rate obtained may be related to pegmatite bodies in a nearby area that contain uranium minerals. However, based on the development of this research, the results indicate that further study in this area is needed in order to infer damage associated with mining of kaolin in the Serido-PB area. (Author)

Engineering Characteristics of Chemically Treated Water-Repellent Kaolin

Directory of Open Access Journals (Sweden)

Youngmin Choi

2016-12-01

Full Text Available Water-repellent soils have a potential as alternative construction materials that will improve conventional geotechnical structures. In this study, the potential of chemically treated water-repellent kaolin clay as a landfill cover material is explored by examining its characteristics including hydraulic and mechanical properties. In order to provide water repellency to the kaolin clay, the surface of clay particle is modified with organosilanes in concentrations (CO ranging from 0.5% to 10% by weight. As the CO increases, the specific gravity of treated clay tends to decrease, whereas the total organic carbon content of the treated clay tends to increase. The soil-water contact angle increases with an increase in CO until CO = 2.5%, and then maintains an almost constant value (≈134.0°. Resistance to water infiltration is improved by organosilane treatment under low hydrostatic pressure. However, water infiltration resistance under high hydrostatic pressure is reduced or exacerbated to the level of untreated clay. The maximum compacted dry weight density decreases with increasing CO. As the CO increases, the small strain shear modulus increases, whereas the effect of organosilane treatment on the constrained modulus is minimal. The results indicate that water-repellent kaolin clay possesses excellent engineering characteristics for a landfill cover material.

Engineering Characteristics of Chemically Treated Water-Repellent Kaolin

Science.gov (United States)

Choi, Youngmin; Choo, Hyunwook; Yun, Tae Sup; Lee, Changho; Lee, Woojin

2016-01-01

Water-repellent soils have a potential as alternative construction materials that will improve conventional geotechnical structures. In this study, the potential of chemically treated water-repellent kaolin clay as a landfill cover material is explored by examining its characteristics including hydraulic and mechanical properties. In order to provide water repellency to the kaolin clay, the surface of clay particle is modified with organosilanes in concentrations (CO) ranging from 0.5% to 10% by weight. As the CO increases, the specific gravity of treated clay tends to decrease, whereas the total organic carbon content of the treated clay tends to increase. The soil-water contact angle increases with an increase in CO until CO = 2.5%, and then maintains an almost constant value (≈134.0°). Resistance to water infiltration is improved by organosilane treatment under low hydrostatic pressure. However, water infiltration resistance under high hydrostatic pressure is reduced or exacerbated to the level of untreated clay. The maximum compacted dry weight density decreases with increasing CO. As the CO increases, the small strain shear modulus increases, whereas the effect of organosilane treatment on the constrained modulus is minimal. The results indicate that water-repellent kaolin clay possesses excellent engineering characteristics for a landfill cover material. PMID:28774098

Parasitoids of boll weevil Anthonomus grandis and resident predators in kaolin-treated cotton

Directory of Open Access Journals (Sweden)

Roberta Leme Santos

2013-12-01

Full Text Available Simultaneous use of control methods is essential to reach success in managing arthropod pests. The current study investigated the effect of kaolin application on resident predators in the cotton plant canopy and parasitism of boll weevil on abscised squares in the field, and parasitism of boll weevil in the laboratory. Predators Araneae, Formicidae, Chrysopidae, and Coccinellidae showed similar seasonal densities for kaolin-treated and untreated cotton fields as well as the emergence rate of the parasitoids Bracon vulgaris Ashmead (Hymenoptera: Braconidae and Catolaccus grandis Burks (Hymenoptera: Pteromalidae from abscised field-collected structures. Under laboratory conditions, the parasitism of boll weevil larvae infesting squares was similar when treated and untreated squares with kaolin were offered to the parasitoid under free choice test. Therefore, the results show that spraying cotton fields with kaolin does not affect the natural biological control by parasitoids of boll weevil and pink bollworm and resident predators naturally occurring in cotton fields.

Treatment of Waste Lubricating Oil by Chemical and Adsorption Process Using Butanol and Kaolin

Science.gov (United States)

Riyanto; Ramadhan, B.; Wiyanti, D.

2018-04-01

Treatment of waste lubricating oil by chemical and adsorption process using butanol and kaolin has been done. Quality of lubricating oil after treatment was analysis using Atomic Absorption Spectrophotometer (AAS) and Gas Chromatography-Mass Spectrometry (GC-MS). The effects of the treatment of butanol, KOH, and kaolin to metals contain in waste lubricating oil treatment have been evaluated. Treatment of waste lubricating oil has been done using various kaolin weight, butanol, and KOH solution. The result of this research show metal content of Ca, Mg, Pb, Fe and Cr in waste lubricating oil before treatment are 1020.49, 367.02, 16.40, 36.76 and 1,80 ppm, respectively. The metal content of Ca, Mg, Pb, Fe and Cr in the waste lubricating oil after treatment are 0.17, 9.85, 34.07, 78.22 and 1.20 ppm, respectively. The optimum condition for treatment of waste lubricating oil using butanol, KOH, and kaolin is 30 mL, 3.0 g and 1.5 g, respectively. Chemical and adsorption method using butanol and kaolin can be used for decrease of metals contain in waste lubricating oil.

Effects of kaolin particle films on the life span of an orb-weaver spider.

Science.gov (United States)

Benhadi-Marín, Jacinto; Pereira, José Alberto; Santos, Sónia A P

2016-02-01

Araniella cucurbitina (Araneae: Araneidae) is a widespread orb-weaver spider commonly found in agroecosystems. Mineral particle films such as kaolin, due to their protective or anti-feeding action, can represent an alternative to pesticides, especially in organic farming systems, but little is known about its effects on A. cucurbitina. Therefore, we tested the effect of kaolin sprays on the life span of A. cucurbitina under laboratory conditions. Four treatments were tested encompassing different exposure routes. Thus, kaolin sprays were applied on (i) the surface, (ii) the prey (fly), (iii) the spider and (iv) both spider & prey. A control group was tested with water in each treatment. Results showed that sprays of kaolin significantly affected the survival of A. curcubitina when applications were done on the surface and on both spider & prey registering a reduction of 48% and 56%, respectively. Spiders in control obtained higher probability of reaching alive at the end of the assay than those treated with kaolin. Differences observed can be explained by the feeding behavior of the species and may depend on the consumption of the web by the spider and the ratio spider/fly for body size. Copyright © 2015 Elsevier Ltd. All rights reserved.

Long-Chain Diacrylate Crosslinkers and Use of PEG Crosslinks in Poly(potassium acrylate-acrylic acid/Kaolin Composite Superabsorbents

Directory of Open Access Journals (Sweden)

Koroush Kabiri

2013-01-01

Full Text Available Long-chain diacrylate crosslinkers based on linear α,ω-diols were synthesized and characterized using FTIR and 1H NMR spectroscopy. The highest reaction yield (99.5% was due to polyethylene glycol diacrylate 1000 (PEGDA-1000. Then, kaolin-containing poly(potassium acrylate-acrylic acid superabsorbent composites and kaolin-free counterparts were synthesized using PEGDA-1000.The effect of the crosslinker concentration on swelling, rheological and thermo-mechanical properties was investigated. Absorption capacity of the composite hydrogels (having ~38% kaolin was unexpectedly higher than that of kaolin-free hydrogels. This was attributed to an interfering effect of kaolin during the polymerization. Glass transition temperature was increased with crosslinker concentration enhancement and addition of kaolin up to about 10oC and 28oC, respectively. Making such K-containing superabsorbents may be taken as an effective action to achieve more durable and cheaper superabsorbents for agricultural uses.

Side effects of kaolin particle films on apple orchard bug, beetle and spider communities

NARCIS (Netherlands)

Marko, V.; Bogya, S.; Kondorosy, E.; Blommers, L.H.M.

2010-01-01

The effects of multiple applications of hydrophobic kaolin particle film on apple orchard bug (Heteroptera), beetle (Coleoptera) and spider (Araneae) assemblages were studied in the Netherlands. Insecticide-free orchard plots served as a control. The kaolin applications significantly reduced the

Kaolin Quality Prediction from Samples: A Bayesian Network Approach

International Nuclear Information System (INIS)

Rivas, T.; Taboada, J.; Ordonez, C.; Matias, J. M.

2009-01-01

We describe the results of an expert system applied to the evaluation of samples of kaolin for industrial use in paper or ceramic manufacture. Different machine learning techniques - classification trees, support vector machines and Bayesian networks - were applied with the aim of evaluating and comparing their interpretability and prediction capacities. The predictive capacity of these models for the samples analyzed was highly satisfactory, both for ceramic quality and paper quality. However, Bayesian networks generally proved to be the most useful technique for our study, as this approach combines good predictive capacity with excellent interpretability of the kaolin quality structure, as it graphically represents relationships between variables and facilitates what-if analyses.

Facile Selective and Diverse Fabrication of Superhydrophobic, Superoleophobic-Superhydrophilic and Superamphiphobic Materials from Kaolin.

Science.gov (United States)

Qu, Mengnan; Ma, Xuerui; He, Jinmei; Feng, Juan; Liu, Shanshan; Yao, Yali; Hou, Lingang; Liu, Xiangrong

2017-01-11

As the starting material, kaolin is selectively and diversely fabricated to the superhydrophobic, superoleophobic-superhydrophilic, and superamphiphobic materials, respectively. The wettability of the kaolin surface can be selectively controlled and regulated to different superwetting states by choosing the corresponding modification reagent. The procedure is facile to operate, and no special technique or equipment is required. In addition, the procedure is cost-effective and time-saving and the obtained super-repellent properties are very stable. The X-ray photoelectron spectroscopy analysis demonstrates different changes of kaolin particles surfaces which are responsible for the different super-repellency. The scanning electron microscopy displays geometric micro- and nanometer structures of the obtained three kinds of super-repellent materials. The results show that kaolin has good applications in many kinds of superwetting materials. The method demonstrated in this paper provides a new strategy for regulating and controlling the wettability of solid surfaces selectively, diversely, and comprehensively.

Infrared detection of the mineralogical aspects that influence the processing of calcined kaolin

Science.gov (United States)

Groenheide, Stefan; Guatame-Garcia, Adriana; Buxton, Mike; van der Werff, Harald

2017-04-01

Calcined kaolin is an industrial minerals product used in the production of paper, paint, rubber and other specialty applications. It is produced from kaolinite through a series of refinement steps and final calcination at temperatures of above 900°C, with the aim of generating a whiter and more abrasive material. The raw kaolin ore is a mixture of clay minerals, quartz and feldspars, where kaolinite is the main constituent. The optimal kaolin ores to feed the processing plant should ideally have high kaolinite abundance, be free in Fe-bearing mineralogy (to avoid influence in the colour of the product), and the kaolinite itself should be of high crystallinity (to ensure the correct abrasiveness after calcination). This work presents a case study from the kaolin deposits in the St. Austell Granite (South-West England), which are known for their high quality and world-class size. In this area, the kaolin is of primary-hydrothermal origin, with mineral associations that are related to the genetic history. The eventual depletion of the high-quality reserves is bringing now the attention to the lower grade zones, where the amount of impurities increases. As a consequence, it is critical to developing strategies that ensure the supply of high-quality ore to the processing plant. For this, it is necessary to acquire a thorough knowledge of the ore, including relative abundance of the minerals and their textural relationships. Hyperspectral images in the visible-near infrared (VNIR) and short-wave infrared (SWIR) ranges were collected from drill cores and run-off-mine (ROM) samples, obtained from one of the kaolin pits in the St. Austell area, where the kaolin quality is known to be lower than in the rest of the deposit. A series of mineral maps were generated to assess the distribution, texture and abundance of the Fe-bearing mineralogy and the other kaolin-associated minerals, as well as the variations in the crystallinity of kaolinite. The mineral maps enabled the

Recent development of high gradient superconducting magnetic separator for kaolin in China

Energy Technology Data Exchange (ETDEWEB)

Zhu, Zian; Wang, Meifen; Ning, Fei Peng; Yang, Huan; Zhang, Guoqing; Hou, Zhi Long; Liu, Zhaong Xiu; Dai, Zhong [Institute of High Energy Physics and University of Chinese Academy of Sciences, Beijing (China); Li, Pei Yong; Zhang, Yiting; Wang, Zhaolian [Weifang Xinli Superconducting Technology Co.,Ltd., Weifang (China)

2017-03-15

A series of high gradient superconducting magnetic separator (HGMS) for kaolin has been developed. It is used for processing kaolin to increase the brightness or whiteness whether it is for paper or ceramic applications. The HGMS system mainly consists of a solenoid magnet with a zero boil-off helium cryostat, a double reciprocating canisters system, and a PLC (Process Logic Controller) fully automatic control system based on SCADA (Supervisory Control and Data Acquisition) system. We have successfully developed CGC-5.5/300 and CGC-5.0/500 HGMS systems in the recent years, and now three sets of them are on-site operation in different customers. This paper will present recent progress of the HGMS system, the results of some experiments on processing kaolin clay used HGMS, and the on-site operation.

Recent development of high gradient superconducting magnetic separator for kaolin in China

International Nuclear Information System (INIS)

Zhu, Zian; Wang, Meifen; Ning, Fei Peng; Yang, Huan; Zhang, Guoqing; Hou, Zhi Long; Liu, Zhaong Xiu; Dai, Zhong; Li, Pei Yong; Zhang, Yiting; Wang, Zhaolian

2017-01-01

A series of high gradient superconducting magnetic separator (HGMS) for kaolin has been developed. It is used for processing kaolin to increase the brightness or whiteness whether it is for paper or ceramic applications. The HGMS system mainly consists of a solenoid magnet with a zero boil-off helium cryostat, a double reciprocating canisters system, and a PLC (Process Logic Controller) fully automatic control system based on SCADA (Supervisory Control and Data Acquisition) system. We have successfully developed CGC-5.5/300 and CGC-5.0/500 HGMS systems in the recent years, and now three sets of them are on-site operation in different customers. This paper will present recent progress of the HGMS system, the results of some experiments on processing kaolin clay used HGMS, and the on-site operation

PHYSICAL PROPERTIES OF KAOLIN/SAND SLURRY USED DURING SUBMERSIBLE MIXER PUMP TESTS AT TNX

International Nuclear Information System (INIS)

HANSEN, ERICH

2005-01-01

The purpose of this task is to characterize the physical properties of the kaolin/sand slurries used during the testing of a new submersible mixer pump (SMP) which had undergone performance testing at the TNX Waste Tank mockup facility from July 2004 through May 2005. During this time period, four identical SMPs were subjected to various water tests and four different tests using different batches of kaolin/sand slurries. The physical properties of the kaolin/sand slurries were measured for three of the four tests. In these tests, three different sample locations were used to pull samples, the SMP cooling water exit (CWE), the SMP fluid flow field (FFF), and SMP effective cleaning radius (ECR). The physical properties measured, though not for each sample, included rheology, weight percent total solids (wt% TS), density, kaolin/sand slurry particle size distribution (PSD), weight percent and particles size distribution of material greater than 45 microns

Adsorption of U(VI) onto kaolin studied by batch method

International Nuclear Information System (INIS)

Hongxia Zhang; Zhi Liu; Peizhuo Hu; Tonghuan Liu; Wangsuo Wu

2013-01-01

Adsorption of U(VI) on purified kaolin was studied by batch methods under ambient conditions, including contact time, pH, fulvic acid, etc. Three kinetic models were used to model the kinetic adsorption which was very well described by the pseudo-second-order rate equation, and the activation energy of adsorption was 52.20 kJ/mol. The Freundlich and Dubinin-Radushkevich models fitted the experimental data better than the Langmuir model for the adsorption and desorption isotherms. The thermodynamic parameters indicated that the adsorption of U(VI) on kaolin was an endothermic and spontaneous process. (author)

Flotation of kaolinite from tailings of kaolin-washing plants by cationic collectors

OpenAIRE

Barani Kianoush

2016-01-01

Traditional processing of kaolin is achieved by dispersion of the mined ore and classification by means of multistage hydrocyclones. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back to the quarry. In this research recovery of kaolinite from tailings of the Zonoupz kaolin washing plant, which is located in Iran, was investigated by cationic flotation. Flotation experiments showed that flotation of kaolinite from tailings was much better in an ac...

Evaluation of The Use of Bentonite, Kaolin and Feldspar For Immobilizing The Uranium Radionuclide Slugdewaste

International Nuclear Information System (INIS)

Prayitno

2006-01-01

The experimental investigation on the mixture of bentonite, kaolin, feldspar, sludge waste and with the ratio of bentonite, kaolin, feldspar for evaluating its effectiveness has been done. Experimentally, this investigation is the preliminary study of the use of bentonite, kaolin, feldspar as a material for the immobilization of sludge waste containing material element especially uranium. This investigation was conducted by mixing waste (2,5; 5; 7.5; 10; 12.5 and 15 %) of total weight sludge waste and bentonite, kaolin, feldspar with of 800, 900 and 1000 o C temperature. The obtained the process condition in which the uranium fraction immobilized could be kept in the limit of safety standard for the sludge waste. Therefore, it could be concluded that the addition of hay ash as an additive in the formation of block monolith tend to minimize the leached sludge waste in the leaching media. (author)

Merger of waste in kaolin panels medium density

International Nuclear Information System (INIS)

Bezerra, A.F.C.; Santana, L.N.L.; Neves, G.A.

2011-01-01

Medium-density panels are molded under pressure and temperature and have physical and mechanical properties similar to those of solid wood. Their composition involves fibers of eucalyptus and pine, but other residues as kaolin waste can be incorporated. The objective was to manufacture medium density panels incorporating kaolin waste and compare the physical, chemical and mechanical properties of these with other commercials. The residue was subjected to the following characterization tests: X-ray diffraction, chemical analysis, differential thermal analysis, thermal gravimetric analysis and size analysis.Through the process of pressing the samples were prepared, they were evaluated for their flexural strength and tensile strength perpendicular to the water absorption / swelling in thickness, density and moisture content. According to the analyzed results, we conclude that samples having the residue had lower levels of swelling, tensile and flexural strength and higher levels of absorption.(author)

Bacterial cellulose–kaolin nanocomposites for application as biomedical wound healing materials

International Nuclear Information System (INIS)

Wanna, Dwi; Alam, Parvez; Alam, Catharina; Toivola, Diana M

2013-01-01

This short communication provides preliminary experimental details on the structure–property relationships of novel biomedical kaolin–bacterial cellulose nanocomposites. Bacterial cellulose is an effective binding agent for kaolin particles forming reticulated structures at kaolin–cellulose interfaces and entanglements when the cellulose fraction is sufficiently high. The mechanical performance of these materials hence improves with an increased fraction of bacterial cellulose, though this also causes the rate of blood clotting to decrease. These composites have combined potential as both short-term (kaolin) and long-term (bacterial cellulose) wound healing materials. (paper)

PES-Kaolin Mixed Matrix Membranes for Arsenic Removal from Water.

Science.gov (United States)

Marino, Tiziana; Russo, Francesca; Rezzouk, Lina; Bouzid, Abderrazak; Figoli, Alberto

2017-09-30

The aim of this work was the fabrication and the characterization of mixed matrix membranes (MMMs) for arsenic (As) removal from water. Membrane separation was combined with an adsorption process by incorporating the kaolin (KT2) Algerian natural clay in polymeric membranes. The effects of casting solution composition was explored using different amounts of polyethersufone (PES) as a polymer, polyvinyl-pyrrolidone (PVP K17) and polyethylene glycol (PEG 200) as pore former agents, N -methyl pyrrolidone (NMP) as a solvent, and kaolin. Membranes were prepared by coupling Non-solvent Induced Phase Separation and Vapour Induced Phase Separation (NIPS and VIPS, respectively). The influence of the exposure time to controlled humid air and temperature was also investigated. The MMMs obtained were characterized in terms of morphology, pore size, porosity, thickness, contact angle and pure water permeability. Adsorption membrane-based tests were carried out in order to assess the applicability of the membranes produced for As removal from contaminated water. Among the investigated kaolin concentrations (ranging from 0 wt % to 5 wt %), a content of 1.25 wt % led to the MMM with the most promising performance.

Effect of the rate of calcination of kaolin on the properties of metakaolin-based geopolymers

Directory of Open Access Journals (Sweden)

B.B. Kenne Diffo

2015-03-01

Full Text Available Kaolin samples of the same mass were treated at 700 °C for the same duration of 30 min by varying the rate of calcination (1, 2.5, 5, 10, 15 and 20 °C/min in order to obtain metakaolins which were used to produce geopolymers. Depending on the nature of each type of material, kaolin, metakaolins and geopolymers were characterized using thermal analysis, chemical analysis, XRD, FTIR, particle size distribution, specific surface area, bulk density, setting time and compressive strength. FTIR and XRD analyses showed that metakaolins except at 1 °C/min contained residual kaolinite whose quantity increased with the rate of calcination of kaolin and which influenced the characteristics of geopolymers. Thus as the rate of calcination of kaolin increased, the setting time increased (226 min (rate of 1 °C/min–773 min (rate of 20 °C/min while the compressive strength reduced (49.4 MPa (rate of 1 °C/min–20.8 MPa (rate of 20 °C/min. From the obtained results the production of geopolymers having high compressive strength along with low setting time requires that the calcination of kaolin be carried out at a low rate.

Microstructural analysis of ceramic masses with waste kaolin addition for the red ceramic production

International Nuclear Information System (INIS)

Vida, Talita Almeida; Fagury Neto, Elias; Rabelo, Adriano Alves

2010-01-01

Incorporating reject industrial ceramic mixtures has proved viable in the reduction of environmental liabilities. In this study, we sought to study the potential use of ceramic formulations with the addition of tailings from the production of kaolin clay to the region of the city of Maraba-PA. Formulations were obtained with two clays of this region with the addition of up to 60% by weight of kaolin waste. The microstructural analyses were carried out from the preparation of specimens that were sintered at 1000 and 1200 °C with level 3 hours. The samples prepared were used to observe the microstructure by optical microscope, to determine the constituents of each formulation after burning. And later analysis was performed X-rays diffraction, to quantify the phases present. It was observed that increasing the content of the mixture of kaolin clay caused the reaction of kaolinite forming the primary mullite from 1000 ° C. For a firing temperature around 1200 ° C showed the presence of mullite even the addition of 20% kaolin, noting also the presence of secondary kaolinite. (author)

Assessment of the adsorptive capacity of the Kaolin deposit targeting its use on the removal of colors in aqueous solution

International Nuclear Information System (INIS)

Matos, S.C.; Hildebrando, E.A.

2016-01-01

The Amazonic region has large and valuable kaolin deposits. The state of Para by itself comprises three large industries which process kaolin. It has been noticed that the waste resulting from the processing of kaolin is rich in silico-aluminate, presenting potential in adsorption processes. Thus, this research's objective is to assess the kaolin waste produced during the processing phase, aiming at its application as low cost adsorbent material. For that, the kaolin waste has been characterized by X-ray diffraction and chemical analysis (XRF), and then sieved and calcined at 700 ° C, being then subjected to the adsorption process and observed qualitatively its capacity of retention by methylene blue (AM). Preliminary results show that the kaolin waste has satisfactory adsorption capacity at concentrations of up to 50.0 mg / MP, demonstrating the potential that it be used in the removal of dyes in wastewater treatment. (author)

Characterization of kaolin wastes from kaolin mining industry from the amazon region as raw material for pozzolans production; Caracterizacao dos residuos cauliniticos das industrias de mineracao de caulim da amazonia como materia-prima para producao de pozolanas de alta reatividade

Energy Technology Data Exchange (ETDEWEB)

Barata, M.S.; Angelica, R.S., E-mail: msb@amazon.com.br, E-mail: angelica@ufpa.br [Instituto de Geociencias, Universidade Federal do Para, Belem, PA (Brazil)

2012-01-15

Capim and Jari are the two most important kaolin mining districts of the Brazilian Amazon region. They encompass the major Brazilian reserves of high quality kaolin for the paper coating industry. The kaolin is mined and processed by three major companies responsible for about 500,000 ton of a residue mainly composed of kaolinite. The wastes come mainly from the centrifugation phase of the kaolin beneficiation process and their final destinations are huge sedimentation basins that occupy large areas. The main purpose of this work is to evaluate the physical, chemical and mineralogical characteristics of the kaolin wastes processed from the Capim and Jari region, in order to obtain meta kaolinite, a high reactive pozzolans for the cement industry. When incorporated to ordinary Portland cement such pozzolans increases the concrete and mortars performance. All the residues studied in this work were characterized by means of: X-ray diffraction analysis, differential thermal analysis, infrared spectroscopy, scanning electron microscopy, X-ray fluorescence spectrometry and laser diffraction. Both residues are mainly constitutes by at least 92% of low granulometry kaolinite with specific surface area above 8 m2 /g and mean diameter below 1 {mu}m. Free silica (quartz) contents are below 3%. The high concentration of kaolinite in these residues dispenses rigid control parameters for removal of impurities usually employed in pozzolans production. The Jari kaolin exhibits high disordered kaolinite in comparison with the high ordered kaolinite of the Capim region and gives rise to higher desidroxilation degree at lower temperatures. It points to energy saving and reducing costs during the production of a pozzolans. The results are satisfactory and reveal that both kaolin wastes are excellent raw material for the production of high reactive meta kaolin. (author)

Kaolin from Acoculco (Puebla, Mexico) as a raw material: mineralogical and thermal characterization

OpenAIRE

Garcia Vallès, Maite; Pi, T.; Alfonso, P.; Canet, C.; Martínez Manent, Salvador; Jiménez-Franco, A.; Tarragó Aymerich, Mariona; Hernández-Cruz, B.

2015-01-01

The present study determined the mineralogy and thermal properties of kaolin from Acoculco (Puebla), at the eastern Trans-Mexican Volcanic Belt and compared it with the nearby deposits of Agua Blanca (Hidalgo) and Huayacocotla (Veracruz). The mineralogy of the kaolins was determined by X-ray diffraction, infrared spectroscopy and scanning electron microscopy. Thermal behaviour was studied by differential thermal analysis, dilatometry and hot-stage microscopy. The Acoculco deposit is composed ...

Physicochemical Evaluation of Industrial Potentialities of Getso Kaolin

African Journals Online (AJOL)

2017-08-13

Aug 13, 2017 ... manufacturing sector. In this study kaolin from Getso, Kano state, northern part of Nigeria was characterized ... foreign import, leaving a supply gap of over. 250,000 .... the presence of mica; the strong band at 3694 cm-1. 80.53.

Contemporary technology of enrichment of Angren deposit of kaolins. I. Using a ultrasonic dispersion for shallowing of raw materials

International Nuclear Information System (INIS)

Krivorotov, V.F.; Usmanov, Zh.M.; Fridman, A.A.

2012-01-01

Optimal parameters of ultrasonic dispersion at enrichment of Angren kaolins are presented. It has been stated that the granule sizes of the kaolin-powder produced by this technology are 0.15-4.0 μm, and 75% of particles have sizes 0.15-1.5 μm. The whiteness of the kaolin-powder amounts 80 - 82%. (authors)

Incorporation of feasibility study of residue thin kaolin in of porcelain formulations production

International Nuclear Information System (INIS)

Almeida, V.S. de; Ferreira, E.C.; Oliveira, T.M. de; Freitas, K.D. de Araujo; Soares Filho, J.E.; Sousa, F.J.P. de

2016-01-01

The porcelain is the more advanced product among traditional ceramics due to the high technology used in its manufacture and its excellent technological and aesthetic properties. Due to the continuing worldwide development, kaolin processing industries have increased their productivity and consequently generating large amounts of waste, contributing to environmental degradation. Studies are being conducted to analyze the incorporation of such wastes in the ceramic mass compositions. The objective of this study was to evaluate 4 formulations of porcelain as the possibility of using waste coming from the last stage of kaolin processing. Processing occurred by wet grinding process, with uniaxial compacting pressure of 45 MPa after heat treatment at 1250 ° C. Technological tests were carried out physical and mechanical product. The results showed that the addition of fine kaolin residue was presented as an efficient alternative for the porcelain industry. (author)

Novel kaolin/polysiloxane based organic-inorganic hybrid materials: Sol-gel synthesis, characterization and photocatalytic properties

Science.gov (United States)

dos Reis, Glaydson Simões; Lima, Eder Cláudio; Sampaio, Carlos Hoffmann; Rodembusch, Fabiano Severo; Petter, Carlos Otávio; Cazacliu, Bogdan Grigore; Dotto, Guillherme Luiz; Hidalgo, Gelsa Edith Navarro

2018-04-01

New hybrid materials using kaolin and the organosilicas methyl-polysiloxane (MK), methyl-phenyl-polysiloxane (H44), tetraethyl-ortho-silicate (TEOS) and 3-amino-propyl-triethoxysilane (APTES) were obtained by sol-gel process. These materials presented specific surfaces areas (SBET) in the range of 20-530 m2 g-1. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) showed remarkable differences between the kaolin and hybrid structures. Thermogravimetric analysis (TGA) revealed that the hybrid materials presented higher thermal stability when compared with their precursors. The electronic properties of the materials were also studied by Ultraviolet-Visible Diffuse Reflectance Absorption (DRUV) and Diffuse Reflectance spectroscopy (DR), where a new absorption band was observed located around 400-660 nm. In addition, these materials exhibit a decrease in DR from 30% to 70% in the blue-cyan green region and are significantly more transparent in the UV region than the kaolin, which could be useful for photocatalysis applications. These results show that the electronic structure of the final material was changed, indicating a significant interaction between the kaolin and the respective silica derivative. These findings support the main idea of the hybridization afforded by pyrolysis between kaolin and organosilica precursors. In addition, as a proof of concept, these hybrid materials were successfully employed as photocatalyst in the photoreduction of Cr(VI) to Cr(III).

Facile Fabrication of a Hierarchical Superhydrophobic Coating with Aluminate Coupling Agent Modified Kaolin

OpenAIRE

Hui Li; Mengnan Qu; Zhe Sun; Jinmei He; Anning Zhou

2013-01-01

A superhydrophobic coating was fabricated from the dispersion of unmodified kaolin particles and aluminate coupling agent in anhydrous ethanol. Through surface modification, water contact angle of the coating prepared by modified kaolin particles increased dramatically from 0° to 152°, and the sliding angle decreased from 90° to 3°. Scanning electron microscopy was used to examine the surface morphology. A structure composed of micro-nano hierarchical component, combined with the surface modi...

Flotation of kaolinite from tailings of kaolin-washing plants by cationic collectors

Directory of Open Access Journals (Sweden)

Barani Kianoush

2016-01-01

Full Text Available Traditional processing of kaolin is achieved by dispersion of the mined ore and classification by means of multistage hydrocyclones. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back to the quarry. In this research recovery of kaolinite from tailings of the Zonoupz kaolin washing plant, which is located in Iran, was investigated by cationic flotation. Flotation experiments showed that flotation of kaolinite from tailings was much better in an acidic than in an alkaline medium containing cationic collectors.

Why Wet Kaolin can be used as a Crustal Analog and its Application to Fault Evolution at Restraining Bends

Science.gov (United States)

Cooke, M. L.; van der Elst, N.; Schottenfeld, M. T.

2010-12-01

To simulate geologic deformation on observable time and length scales within the lab, a subset of analog modelers have used wet kaolin. Unlike the more often used sand, wet kaolin beautifully exhibits detailed fault structures. Furthermore, faults within the kaolin are more readily reactivated than those in sand. The low plasticity of kaolin (compared to other clays) gives it low shear strength. Consequently, the clay is a suitable analog material if we assume that the wet kaolin deforms by coulomb frictional failure. Koalin generally deforms as a Bingham solid and exhibits more complex deformation than the perfectly plastic behavior assumed with Coulomb failure. We performed fall cone and rheometric tests on wet kaolin to refine our quantitative understanding of its rheology. We use North American wet kaolin with density 1.65-1.7 g/cm3 and water content of 37.5-38.5%. The fall cone tests reveal that the undrained shear strength (100-160 Pa) is greater than previously measured with a viscometer. The rheometer tests show that the wet koalin exhibits many of the same properties of crustal materials including: 1) elastic behavior at low strains, 2) stress relaxation at near-failure strains, 3) creep under static load, 4) yield strength sensitive to strain rate and 5) rate and state dependent failure. Armed with quantitative values for this complex deformation, we can better scale the length and strain rate of the wet koalin experiments to specific crustal settings. Experiments of deformation around restraining bends show features very similar to those found in natural examples. The detailed fault structures produced in the wet kaolin can be analyzed to understand the evolution of active faulting at restraining bends.

Geology and industrial mineral resources of the Macon-Gordon Kaolin District, Georgia

Science.gov (United States)

Buie, Bennett Frank; Hetrick, J.H.; Patterson, S.H.; Neeley, C.L.

1979-01-01

The Macon-Gordon kaolin district is about 80 miles (130 km) southeast of Atlanta, Georgia. It extends across the boundary between, and includes parts of, the Piedmont and Atlantic Coastal Plain physiographic provinces. The rocks in the Piedmont are mainly intensely folded sericite schist and granite gneiss containing irregular masses of amphibolite and feldspathic biotite gneiss and scattered igneous intrusive rocks. Most of the crystalline rocks are thought to be of Paleozoic age, but some of the intrusive rocks may be younger. The crystalline rocks are cut by a major unconformity and are overlain by sedimentary formations ranging in age from Cretaceous to Miocene. The valuable kaolin deposits occur in the Cretaceous beds, undivided, and in the Huber Formation which is of Paleocene to middle Eocene age. The resources of kaolin in the district are estimated in millions of metric tons as follows: reserves, 100; subeconomic resources, 700 to 900; undiscovered resources, probably 700 to 1,000. In addition to kaolin, the leading mineral commodity mined in the district, crushed stone and sand are now being produced, and fuller's earth and a minor amount of limestone were formerly produced. The crushed stone is quarried from igneous rocks in the Piedmont province. The sand is washed from the Cretaceous beds, undivided. The fuller's earth was mined from the Twiggs Clay Member of the Barnwell Formation, and limestone was dug from the Tivola Limestone.

CERAMIC PROPERTIES OF PUGU KAOLIN CLAYS. PART 2 ...

African Journals Online (AJOL)

a

PART 2: EFFECT OF PHASE COMPOSITION ON FLEXURAL STRENGTH ... working in this field have established factors controlling the various ... The raw materials selected were kaolin clays from Pugu deposit in Tanzania, Norfloat potash .... the total mullite contents present in the samples since the method used does.

Experiment study on the thermal properties of paraffin/kaolin thermal energy storage form-stable phase change materials

International Nuclear Information System (INIS)

Lv, Peizhao; Liu, Chenzhen; Rao, Zhonghao

2016-01-01

Highlights: • Different particle sizes of kaolin were employed to load paraffin. • The effects and reasons of particle size on thermal conductivity were studied. • Thermal property and thermal stability of the composites were investigated. • The leakage and thermal storage and release rate of the composites were studied. • The effect of vacuum impregnation method on thermal conductivity was investigated. - Abstract: In this paper, different particle sizes of kaolin were employed to incorporate paraffin via vacuum impregnation method. The paraffin/kaolin composites were characterized by Scanning Electron Microscope (SEM), X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Differential Scanning Calorimeter (DSC) and Thermogravimetry (TG). The results showed that the paraffin/kaolin composite with the largest particle size of kaolin (K4) has the highest thermal conductivity (0.413 W/(m K) at 20 °C) among the diverse composites. The latent heat capacity of paraffin/K4 is 119.49 J/g and the phase change temperature is 62.4 °C. In addition, the thermal properties and thermal conductivities of paraffin/K4 with different mass fraction of K4 (0–60%) were investigated. The thermal conductivities of the composites were explained in microcosmic field. The phonon mean free path determines the thermal conductivity, and it can be significantly affected by temperature and the contact surface area. The leaks, thermal storage and release properties of pure paraffin and paraffin/kaolin composites were investigated and the composites presented good thermal stabilities.

Evaluation of the potential of waste processing of secondary kaolin of Para for use in porcelain

International Nuclear Information System (INIS)

Junior, V.G.L.; Fernandes, L.L.; Fagury Neto, E.; Rabelo, A.A.

2012-01-01

The kaolin waste evaluated is characterized as secondary due be coming from the steps of centrifugation, magnetic separation, bleaching and filtering, which gives a ratio which provides a significant residue, about 26% of their gross, that is intended for embankments. This study aimed to evaluate the potential of reusing the kaolin waste processing from Imerys RCC in the region of Barcarena (PA) in formulation of ceramic bodies for porcelain tiles production, seeking to property of maximum water absorption of 0.5 % for this type of product. The residue from the production of kaolin had been previously characterized by X-ray diffraction and there is a significant amount of kaolinite concentration. After the ceramic processing to obtain the test specimens with different amounts of residue replacing the kaolin, these were sintered using 1200, 1220 and 1240 °C for 2 hours. The formulations were evaluated by water absorption, linear firing shrinkage and modulus of rupture at a three-point bending setup of the pieces produced. (author)

Characterization of kaolin dispersion using acoustic and electroacoustic spectroscopy

Directory of Open Access Journals (Sweden)

Dohnalová Ž.

2008-01-01

Full Text Available The objective of this work is the investigation of the kaolin dispersion by the ultrasonic techniques. In contact with aqueous solution clay minerals show cation - exchange properties and certain degree of dissolution or rather selective leaching of components. The work is divided into two main parts - determination of zeta potential and particle size distribution. The first part is focused on measuring of zeta potential. Effects of concentration of solid, different kind of electrolytes (0.01 M KCl, 0.01 M MgCl2 and 0.01 M CaCl2, pH and temperature of the dispersions are investigated. The isoelectric points (IEP of kaolin suspension are about pH 4-5. Electrolytes containing monovalent cations such as K+ become zeta potential more negative compared to the values obtained with water. Such behavior is explained by the exchange of K+ ions with H+ ions in the system. When the electrolyte is formed by divalent cations such as Mg2+ or Ca2+, the values of zeta potential become less negative than zeta potential of kaolin in water. The second part is focused on the determination of particle size distribution with respect to dispersing conditions, such as the optimal dispersing agent (Na2SiO3, (NaPO36, Na4P2O7 or Busperse, time and power of ultrasonication and also the tracking of dispersion stability that is expressed by the measuring of particle size distribution during certain time period.

Nibelung-Kaoline-Black band fluit clay - the new key-horizon in the carboniferous system of the Ruhr coal field

Energy Technology Data Exchange (ETDEWEB)

Burger, K.; Otte, M.U. (Bergbau A.G. Lippe, Gelsenkirchen (Germany, F.R.). Abt. Markscheidewesen); Pfisterer, W. (Bergbau A.G. Lippe, Herne (Germany, F.R.). Hauptlaboratorium)

1979-10-01

Based upon the stratigraphic distribution of the kaoline-black-band flint clay in the carbon strata of the Ruhr, the Nibelung-Kaoline-black-band flint clay found in the upper Westphal C (Dorsten strata) is defined to be the new keyhorizon. The position of the discoveries of the kaoline-black-band flint clay, its stratigraphic positions as well as its macroscopic and microscopic characteristics together with the chemical composition are given. Investigations of the structure and minerals content show that the Nibelung-Kaolin-black-band flint clay is a new keyhorizon and is of great importance for the stratigraphy of the upper Westfal C. Its position within the system is represented by strata sections.

Potassium Capture by Kaolin, Part 2: K2CO3, KCI, and K2SO4

DEFF Research Database (Denmark)

Wang, Guoliang; Jensen, Peter Arendt; Wu, Hao

2018-01-01

residence time on the reaction was investigated. The results showed that the K-capture level (C-K) (g potassium reacted by per g kaolin available) of K2CO3 and KCI by kaolin generally followed the equilibrium predictions at temperatures above 1100 degrees C, when using a kaolin particle size of D50 = 5.......47 mu m and a residence time of 1.2 s. This revealed that a nearly full conversion was obtained without kinetic or transport limitations at the conditions applied. At 800 and 900 degrees C, the measured conversions were lower than the equilibrium predictions, indicating that the reactions were either...

Removal of heavy metals from kaolin using an upward electrokinetic soil remedial (UESR) technology

International Nuclear Information System (INIS)

Wang, J.-Y.; Huang, X.-J.; Kao, Jimmy C.M.; Stabnikova, Olena

2006-01-01

An upward electrokinetic soil remedial (UESR) technology was proposed to remove heavy metals from contaminated kaolin. Unlike conventional electrokinetic treatment that uses boreholes or trenches for horizontal migration of heavy metals, the UESR technology, applying vertical non-uniform electric fields, caused upward transportation of heavy metals to the top surface of the treated soil. The effects of current density, treatment duration, cell diameter, and different cathode chamber influent (distilled water or 0.01 M nitric acid) were studied. The removal efficiencies of heavy metals positively correlated to current density and treatment duration. Higher heavy metals removal efficiency was observed for the reactor cell with smaller diameter. A substantial amount of heavy metals was accumulated in the nearest to cathode 2 cm layer of kaolin when distilled water was continuously supplied to the cathode chamber. Heavy metals accumulated in this layer of kaolin can be easily excavated and disposed off. The main part of the removed heavy metals was dissolved in cathode chamber influent and moved away with cathode chamber effluent when 0.01 M nitric acid was used, instead of distilled water. Energy saving treatment by UESR technology with highest metal removal efficiencies was provided by two regimes: (1) by application of 0.01 M nitric acid as cathode chamber influent, cell diameter of 100 mm, duration of 18 days, and constant voltage of 3.5 V (19.7 kWh/m 3 of kaolin) and (2) by application of 0.01 M nitric acid as cathode chamber influent, cell diameter of 100 cm, duration of 6 days, and constant current density of 0.191 mA/cm 2 (19.1 kWh/m 3 of kaolin)

Electrochemical oxidation of pulp and paper making wastewater assisted by transition metal modified kaolin

International Nuclear Information System (INIS)

Wang Bo; Gu Lin; Ma Hongzhu

2007-01-01

The electrochemical oxidation of pulp and paper making wastewater assisted by transition metal (Co, Cu) modified kaolin in a 200 ml electrolytic batch reactor with graphite plate as electrodes was investigated. H 2 O 2 , which produced on the surface of porous graphite cathode, would react with the catalysts to form strong oxidant (hydroxyl radicals) that can in turn destruct the pollutants adsorbed on the surface of kaolin. The transition metal (Co, Cu) modified kaolin was also characterized by XRD and SEM before and after the modification and the results showed that the transition metals were completely supported on kaolin and formed a porous structure with big BET surface. The mechanism was proposed on the basis of XPS analysis of the catalyst after the degradation process. Series of experiments were also done to prove the synergetic effect of the combined oxidation system and to find out the optimal operating parameters such as initial pH, current density and amount of catalyst. From the results it can be founded that when the initial pH was at 3, current density was 30 mA cm -2 ; catalyst dose was 30 g dm -3 , COD (chemical oxygen demand) removal could reach up to 96.8% in 73 min

Preparation and Characterization of Acid and Alkaline Treated Kaolin Clay

Directory of Open Access Journals (Sweden)

Sachin Kumar

2013-06-01

Full Text Available Kaolin was refluxed with HNO3, HCl, H3PO4, CH3COOH, and NaOH of 3M concentration at 110 °C for 4 hours followed by calcination at 550 °C for 2 hours. The physico-chemical characteristics of resulted leached kaolinite clay were studied by XRF, XRD, FTIR, TGA, DTA, SEM and N2 adsorption techniques. XRF and FTIR study indicate that acid treatment under reflux conditions lead to the removal of the octahedral Al3+ cations along with other impurities. XRD of acid treated clay shows that, the peak intensity was found to decrease. Extent of leaching of Al3+ ions is different for different acid/base treatment. The acid treatment increased the Si/Al ratio, surface area and pore volume of the clay. Thus, the treated kaolin clay can be used as promising adsorbent and catalyst supports. © 2013 BCREC UNDIP. All rights reservedReceived: 1st March 2013; Revised: 9th April 2013; Accepted: 19th April 2013[How to Cite: Kumar, S., Panda, A. K., Singh, R.K. (2013. Preparation and Characterization of Acids and Alkali Treated Kaolin Clay. Bulletin of Chemical Reaction Engineering & Catalysis, 8 (1: 61-69. (doi:10.9767/bcrec.8.1.4530.61-69][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.8.1.4530.61-69] |View in  |

Recovery of kaolinite from tailings of Zonouz kaolin-washing plant by flotation-flocculation method

OpenAIRE

Kianoush Barani; Masoud Kalantari

2018-01-01

The traditional processing of kaolin is achieved by dispersion of the mined ore and classification by multistage hydrocyclone plants. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back into the quarry. In this research, recovery of kaolinite from tailings of Zonouz kaolin washing plant, which is located in Iran was investigated by flotation and flotation- flocculation. Flotation experiments show that the flotation of kaolinite from the tailings i...

Composite pigments based on surface coated kaolin and metakaolin

Czech Academy of Sciences Publication Activity Database

Štengl, Václav; Popelková, Daniela; Matys Grygar, Tomáš

2014-01-01

Roč. 101, NOV (2014), s. 149-158 ISSN 0169-1317 R&D Projects: GA MPO FR-TI1/006 Institutional support: RVO:61388980 Keywords : Kaolin * Homogeneous hydrolysis * Thioacetamide * Urea * Mullite * Metakaolin Subject RIV: CA - Inorganic Chemistry Impact factor: 2.467, year: 2014

Comparative studies on physico-mechanical properties of composite materials of low density polyethylene and raw/calcined kaolin

Directory of Open Access Journals (Sweden)

Amit Mallik

2015-06-01

Full Text Available The paper describes the preparation of the composite materials of low density polyethylene (LDPE as the base mixed separately with raw kaolin and the same calcined at 800 °C under the same variation in weight percentage using single-screw extruder and a mixing machine operated at a temperature between 190 and 200 °C. Some of the mechanical and physical properties such as Young's modulus, elongation at break, shore hardness and water absorption were determined at different weight fractions of filler (0, 2, 7, 10 and 15%. It was found that the addition of filler increases the mechanical properties. Absorption test was done in water at different immersion times for different composites. The degree of water absorption of composite materials was found to decrease with increasing wt% of kaolin filler (0–15% according to Fick's law. Calcined kaolin produces better mechanical properties than raw kaolin.

Effects of Dietary Kaolin Supplementation on the Growth ...

African Journals Online (AJOL)

One hundred and sixty (160) Anak 2000 day-old broiler chicks were used to investigate the effects of kaolin on the haematology and growth performance of broilers. The chicks were randomly assigned to four treatments, each treatment consisting of four pens with 10 chicks per pen. The four treatments were; basal diet only ...

Electrical Properties of Zinc-Kaolin Composites below its Percolation ...

African Journals Online (AJOL)

Bheema

In this paper, we present some electrical properties of the zinc-kaolin cermet resistors ..... The temperature coefficient of resistance of a material is generally defined as .... Characterisation and morphological Studies of palladium modified carbon ... conduction and microstructural properties of semiconducting Co-doped TiO2.

Cure characteristics, crosslink density and degree of filler dispersion of kaolin-filled natural rubber compounds in the presence of alkanolamide

Science.gov (United States)

Surya, I.; Hayeemasae, N.; Ginting, M.

2018-03-01

The effects of alkanolamide (ALK) addition on cure characteristics, crosslink density and degree of filler dispersion of kaolin-filled natural rubber (NR) compounds were investigated. The kaolin filler was incorporated into NR compounds with a fixed loading, 30.0 phr. The ALK was prepared from Refined Bleached Deodorized Palm Stearin (RBDPS), a waste product of cooking oil production, and diethanolamine. The ALK is an oily material and added into the filled NR compounds as a rubber additive at different loadings, 0.0, 3.0, 5.0 and 7.0. The kaolin-filled NR compounds with and without ALK were vulcanized using a semi-efficient vulcanization system. It was found that ALK decreased the scorch and cure times and improved filler dispersion of the kaolin-filled NR compounds. The higher the ALK loading, the shorter were the scorch and cure times. It was also found that ALK increased the crosslink density of kaolin-filled NR compound up to 5.0 phr of loading. Due to its oily properties, The ALK acted as an internal plasticizer which decreased the minimum torque and improved the degree of kaolin dispersion in NR phases. The higher the ALK loading; the lower the minimum torque and better the filler dispersion.

DMC-grafted cellulose as green-based flocculants for agglomerating fine kaolin particles

Directory of Open Access Journals (Sweden)

Meng Li

2018-04-01

Full Text Available Novel cellulose based flocculants C-g-P (DMC with various chain architectures are synthesized through a situ graft copolymerization. The cationic ammonium chloride group (DMC is grafted onto cellulose by two separate inverse emulsion polymerization with γ-methacryloxypropyl trimethoxy silane (KH-570 and double bond addition reactions, which is a new and simple method to employ KH-570 as a bridge for the connection of cellulose matrix and DMC group. The effects of pH, flocculant dose, standing time on turbidity of kaolin suspensions and particle sizes have been studied systematically. In addition, the response surface methodology (RSM study confirms that PAC and C-g-P (DMC have synergy in turbidity removal with a higher removal efficiency of 98.32%. Moreover, C-g-P (DMC 1 has higher removal efficiency with 96.5% at a low dosage of 0.6 mg L−1 and better floc properties than C-g-P (DMC 2 and C-g-P (DMC 3, suggesting that the length and quantity of cationic branch chains play a crucial role in Kaolin flocculation due to their dramatically enhanced bridging effects. Keywords: Cellulose, Cationic flocculant, Inverse emulsion polymerization, Kaolin suspension

Effects of biochar on hydraulic conductivity of compacted kaolin clay.

Science.gov (United States)

Wong, James Tsz Fung; Chen, Zhongkui; Wong, Annie Yan Yan; Ng, Charles Wang Wai; Wong, Ming Hung

2018-03-01

Compacted clay is widely used as capillary barriers in landfill final cover system. Recently, biochar amended clay (BAC) has been proposed as a sustainable alternative cover material. However, the effects of biochar on saturated hydraulic conductivity (k sat ) of clay with high degree of compaction is not yet understood. The present study aims to investigate the effects of biochar on k sat of compacted kaolin clay. Soil specimens were prepared by amending kaolin clay with biochar derived from peanut-shell at 0, 5 and 20% (w/w). The k sat of soil specimens was measured using a flexible water permeameter. The effects of biochar on the microstructure of the compacted clay was also investigated using MIP. Adding 5% and 20% of biochar increased the k sat of compacted kaolin clay from 1.2 × 10 -9 to 2.1 × 10 -9 and 1.3 × 10 -8 ms -1 , respectively. The increase in k sat of clay was due to the shift in pore size distribution of compacted biochar-amended clay (BAC). MIP results revealed that adding 20% of biochar shifted the dominant pore diameter of clay from 0.01-0.1 μm (meso- and macropores) to 0.1-4 μm (macropores). Results reported in this communication revealed that biochar application increased the k sat of compacted clay, and the increment was positively correlated to the biochar percentage. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characterization of silica polymorphs in kaolins by X-ray diffraction before and after phosphoric acid digestion and thermal treatment

International Nuclear Information System (INIS)

Kahraman, Sibel; Oenal, Mueserref; Sarikaya, Yueksel; Bozdogan, Ihsan

2005-01-01

To characterize silica polymorphs (silicas) in some kaolins, orthophosphoric acid digestion (240 deg. C, 15 min), and thermal treatment (1050 deg. C, 24 h) were applied to eight samples. The original, digested, and heated samples were examined by X-ray diffraction (XRD). Crystalline silica quartz (SiO 2 ) was identified from the standard XRD patterns of the original kaolins; all contained quartz. On the other hand, hydrated partially crystalline silicas (SiO 2 .nH 2 O), such as well-ordered opal-C and opal-CT, were not readily distinguished from high-temperature crystalline silica, α-cristobalite, using standard XRD patterns of the original kaolins because, sharp and intense characteristic XRD peaks (h k l = 1 0 1) centered near 0.4 nm for opal-C, opal-CT, and α-cristobalite coincided. In order to distinguish these silicas the XRD patterns of the digested and heated samples were evaluated. It was observed that the 1 0 1 peaks disappear and sharpen in the course of digestion and heating, respectively. Because, the crystallinity of α-cristobalite does not change by these treatments, it was concluded that the kaolins contain opal-C and opal-CT or their mixtures in amorphous opal-A (SiO 2 .nH 2 O), but not α-cristobalite, which is probably human carcinogen. Because, the crystallinity increases in order opal-CT and opal-C, the narrowing in width at half-maximum peak height (FWHM) 1 0 1 must be more for opal-CT than opal-C by heating. Therefore, to distinguish opal-CT and opal-C from each other, the FWHM values before and after the heating process, were examined. Based on the results, it was estimated that six kaolins contain opal-CT in opal-A matrix, one kaolin contains only opal-A in a trace amount, and one kaolin contains non-opals

Flocculation of kaolin and lignin by bovine blood and hemoglobin

Science.gov (United States)

Polymeric flocculants are used extensively for water purification, inhibition of soil erosion, and reduction in water leakage from unlined canals. Production of highly active, renewable polymeric flocculants to replace synthetic flocculants is a priority. Using suspensions of kaolin, flocculation ...

Detection of tPA-Induced Hyperfibrinolysis in Whole Blood by RapidTEG, KaolinTEG, and Functional FibrinogenTEG in Healthy Individuals

DEFF Research Database (Denmark)

Genét, Gustav Folmer; Ostrowski, Sisse Rye; Sørensen, Anne Marie

2012-01-01

hyperfibrinolysis, as compared to standard KaolinTEG, is unknown. To investigate this, the ability of RapidTEG, KaolinTEG, and functional fibrinogenTEG (FFTEG) to detect tPA-induced (tissue plasminogen activator) lysis in whole blood from healthy individuals was investigated. Our hypothesis was that the initial...... powerful clot formation in the RapidTEG assay would reduce the sensitivity as compared to the normally used KaolinTEG assay. We also evaluated the FFTEG assay. Methods: In vitro comparison of the sensitivity of RapidTEG, KaolinTEG, and FFTEG to 1.8 nmol/L tPA in citrated whole blood (299 ± 23 ng/mL plasma......) induced hyperfibrinolysis in 10 healthy individuals and duplicate titration of the tPA whole blood (WB) concentration from 0.09 to 7.2 nmol/L (14-1144 ng/mL plasma) in 1 healthy donor. Results: At 1.8 nmol/L tPA, KaolinTEG, RapidTEG, and FFTEG all detected fibrinolysis but with different sensitivities...

synthesis of zeolite-a using kaolin samples from darazo, bauchi ...

African Journals Online (AJOL)

henry mgbemere

ekpeikenna@gmail.com, ... 13]. Kaolin is a naturally occurring mineral of the clay family and may contain a ..... Properties," World Journal of Nano Science and ... Treatment on Kankara Kaolinite," Opticon1826, vol. 15, pp. 1-5, 2013. .... 36(2) 444-451.

Influence of kaolin addition on the dynamics of oxygen mass transport in polyvinyl alcohol dispersion coatings

OpenAIRE

Nyflött, Åsa; Axrup, Lars; Gunilla, Carlsson; Järnström, Lars; Lestelius, Magnus; Moons, Ellen; Wahlström, Torbjörn

2015-01-01

The permeability of dispersion barriers produced from polyvinyl alcohol (PVOH) and kaolin clay blends coated onto polymeric supports has been studied by employing two different measurement methods: the oxygen transmission rate (OTR) and the ambient oxygen ingress rate (AOIR). Coatings with different thicknesses and kaolin contents were studied. Structural information of the dispersion-barrier coatings was obtained by Fourier transform infrared spectroscopy (FTIR) spectroscopy and scanning ele...

The mechanical and thermal characteristics of phenolic foam reinforced with kaolin powder and glass fiber fabric

Science.gov (United States)

Xiao, Wenya; Huang, Zhixiong; Ding, Jie

2017-12-01

In this work, kaolin powder and glass fiber fabric were added to PF in order to improve its thermal stability and mechanical property. Micro-structures of carbonized PF with kaolin powder were inspected by scanning electron microscopy (SEM) to demonstrate the filler’s pinning effect. SEM results illustrated modified PF had well morphology after high-temperature heat treatment. The Fourier transform infrared spectrometer (FTIR) test was carried out and found that kaolin powder only physically dispersed in PF. The compression test and thermal weight loss test were done on two groups of modified PF (Group A: add powder and fabric; Group B: add powder only). Results showed that all modified PF were better than pure PF, while foams with powder and fabric showed better mechanical characteristic and thermal stability compared with foams with powder only.

Alternatif Pembuatan Biodiesel Melalui Transesterifikasi Minyak Castor (Ricinus communis Menggunakan Katalis Campuran Cangkang Telur Ayam dan Kaolin

Directory of Open Access Journals (Sweden)

Soni - Setiadji

2017-05-01

Full Text Available Biodiesel was produced by transesterification of castor oil (Ricinus communis using a catalyst of CaO and kaolin (CaO / kaolin had been performed. CaO was obtained from the calcination of eggshell. Castor oil is selected as biodiesel feedstock because it belongs to non-food oil and easy to cultivate. In general, the research method aims to comprise the CaO / Kaolin catalysts with a ratio of 15 mmol CaO per 1 gram of kaolin activated using impregnation method and biodiesel produced through transesterification of castor oil using the catalyst at 65 ºC for 8 hours with ratio of castor oil: methanol: catalyst (1: 15: 5% w / w. The reaction is carried out on the reflux system. The XRD analysis show the presence of silica and potassium aluminum silicate hydroxide in the catalyst. The EDS results show the catalyst-forming components CaO and silica. The FTIR analysis results show the absorption peak in the functional group forming the methyl ester compound. Based on the characterization of GC-MS, the largest methyl ester components contained in biodiesel are methyl risinoleate, methyl elaidat, methyl stearate, methyl linoleate, and methyl palmitate. The overall conversion of castor oil to methyl ester using CaO / kaolin catalyst is 97.36%. The largest component in castor oil is risinoleic acid, has been successfully converted to methyl risinoleate by 74.75%.DOI: http://dx.doi.org/10.15408/jkv.v0i0.4778

Synthesis of Gamma-Alumina from Kankara Kaolin as Potential ...

African Journals Online (AJOL)

Engr Solomn Gajere

Large specific surface area gamma-alumina (γ-Al2O3) was synthesized by hydrothermal method using Kankara kaolin as starting material. Thermal treatment of ammonium alum prepared from the filtrate of the dealuminated metakaolin was employed to obtain the alumina. Crystalline aluminum sulfate with 39 wt% Al2O3 ...

Effects of Kaolin Application on Light Absorption and Distribution, Radiation Use Efficiency and Photosynthesis of Almond and Walnut Canopies

Science.gov (United States)

Rosati, Adolfo; Metcalf, Samuel G.; Buchner, Richard P.; Fulton, Allan E.; Lampinen, Bruce D.

2007-01-01

Background and Aims Kaolin applied as a suspension to plant canopies forms a film on leaves that increases reflection and reduces absorption of light. Photosynthesis of individual leaves is decreased while the photosynthesis of the whole canopy remains unaffected or even increases. This may result from a better distribution of light within the canopy following kaolin application, but this explanation has not been tested. The objective of this work was to study the effects of kaolin application on light distribution and absorption within tree canopies and, ultimately, on canopy photosynthesis and radiation use efficiency. Methods Photosynthetically active radiation (PAR) incident on individual leaves within the canopy of almond (Prunus dulcis) and walnut (Juglans regia) trees was measured before and after kaolin application in order to study PAR distribution within the canopy. The PAR incident on, and reflected and transmitted by, the canopy was measured on the same day for kaolin-sprayed and control trees in order to calculate canopy PAR absorption. These data were then used to model canopy photosynthesis and radiation use efficiency by a simple method proposed in previous work, based on the photosynthetic response to incident PAR of a top-canopy leaf. Key Results Kaolin increased incident PAR on surfaces of inner-canopy leaves, although there was an estimated 20 % loss in PAR reaching the photosynthetic apparatus, due to increased reflection. Assuming a 20 % loss of PAR, modelled photosynthesis and photosynthetic radiation use efficiency (PRUE) of kaolin-coated leaves decreased by only 6·3 %. This was due to (1) more beneficial PAR distribution within the kaolin-sprayed canopy, and (2) with decreasing PAR, leaf photosynthesis decreases less than proportionally, due to the curvature of the photosynthesis response-curve to PAR. The relatively small loss in canopy PRUE (per unit of incident PAR), coupled with the increased incident PAR on the leaf surface on

Characterization of ceramic masses using raw material of Para, Brazil: kaolin in natura

International Nuclear Information System (INIS)

Vida, T.A.; Facury Neto, E.; Rabelo, A.A.

2009-01-01

The incorporation rejects to the mixtures has if shown viable in the reduction of the environmental liability and for the obtaining of a better quality of the ceramic mass. In the present work, is tried to study the potentiality of the use of ceramic formulations with the addition of kaolin in natura to the clays. Formulations with two clays of the area of the municipal district of Maraba with addition of up to 60% in kaolin weight were prepared and characterized. For the determination of the physical and mechanical properties proof bodies were made by prensagem uniaxial and later burned in temperature from 900 to 1200 deg C with landing of 3 hours. The raw materials were characterized through diffraction of rays X (DRX) and thermogravimetric analysis. The proof bodies prepared were used for determination of the lineal retraction (RL), absorption of water, apparent porosity, apparent density, loss to the fire and rupture module the flexing. The results were satisfactory for the smallest kaolin tenors in the ceramic mass, and the mass with 20% presented rupture module elevated, in the temperature of 1200 deg C. (author)

Synthesis of Gamma-Alumina from Kankara Kaolin as Potential ...

African Journals Online (AJOL)

In compounded zeolite catalyst it serves as the active matrix which aids the conversion of the bulkiest molecules in the feed owing to its larger pore size than zeolite. Large specific surface area gamma-alumina (γ-Al2O3) was synthesized by hydrothermal method using Kankara kaolin as starting material. Thermal treatment ...

40 CFR 180.1180 - Kaolin; exemption from the requirement of a tolerance.

Science.gov (United States)

2010-07-01

... Kaolin, when used on crops (apples, apricots, bananas, beans, cane berries, citrus fruits, corn, cotton... permit the marketing of the food commodities in this paragraph when treated in accordance with the...

Integrated mined-area reclamation and land-use planning. Volume 3C. A case study of surface mining and reclamation planning: Georgia Kaolin Company Clay Mines, Washington County, Georgia

Energy Technology Data Exchange (ETDEWEB)

Guernsey, J L; Brown, L A; Perry, A O

1978-02-01

This case study examines the reclamation practices of the Georgia Kaolin's American Industrial Clay Company Division, a kaolin producer centered in Twiggs, Washington, and Wilkinson Counties, Georgia. The State of Georgia accounts for more than one-fourth of the world's kaolin production and about three-fourths of U.S. kaolin output. The mining of kaolin in Georgia illustrates the effects of mining and reclaiming lands disturbed by area surface mining. The disturbed areas are reclaimed under the rules and regulations of the Georgia Surface Mining Act of 1968. The natural conditions influencing the reclamation methodologies and techniques are markedly unique from those of other mining operations. The environmental disturbances and procedures used in reclaiming the kaolin mined lands are reviewed and implications for planners are noted.

Caulins brasileiros: alguns aspectos da geologia e da mineralogia Brazilian kaolins: some aspects of the geology and mineralogy

Directory of Open Access Journals (Sweden)

Ian Richard Wilson

1998-08-01

Full Text Available A dimensão do Brasil e a diversidade da geologia se reflete em vários meios nos quais montagens de caulinita foram formadas. Os meios geológicos dos caulins brasileiros podem ser divididos nos seguintes grupos - caulins sedimentares, caulins oriundos de pegmatitas, de rochas graníticas, de rochas vulcânicas, e caulins derivados de anortosito. As argilas sedimentares são encontradas principalmente na bacia amazônica e aquelas adjacentes ao rio Jari estão sendo exploradas comercialmente para exportação como argilas para recobrimento de papel. Os caulins amazônicos são caracterizados por alto teor de ferro e titânia (estruturais com baixos níveis de álcalis e exibindo cristais de caulinita euédricos. As pegmatitas do sudeste, quando não recobertas com óxido de ferro, tem extremamente baixos teores de ferro e titânia e uma mistura de caulinita 7Å / haloisita 10Å ocorre em todos depósitos. As pegmatitas do nordeste produzem caulins constituídos somente por caulinitas euédricas com ausência de haloisita. Os caulins de granito tem geralmente maiores teores de ferro quando comparados com pegmatitas e são raros os depósitos constituídos somente por caulinita, sendo comum uma mistura de caulinita 7Å / haloisita. Os caulins obtidos da pegmatita e do granito são utilizados como cobertura de papel e em cerâmica em geral. Argilas de origem vulcânica são utilizadas em cerâmicas na região. Os caulins obtidos de anortosito são semelhantes em níveis de ferro e titânia àqueles obtidos de caulins graníticos. Montagens de caulinita e pequenas quantidades de haloisita 7Å são encontrados. Essas argilas são usadas tanto em cerâmicas de mesa quanto em preenchimentos para papel.The size of Brazil and the diversity of geology is reflected in varying environments in which kaolinite assemblages have been formed. The geological environments of the Brazilian kaolin may be divided into the following groups - sedimentary kaolin

A Mexican kaolin deposit: XANES characterization, mineralogical phase analysis and applications

Directory of Open Access Journals (Sweden)

Martínez, A.

2009-06-01

Full Text Available A kaolin obtained from Villa de Reyes, a region near to San Luis Potosí (México was characterized by means of X-ray powder diffraction (XRD, optical microscopy (OM, scanning electron microscopy (SEM, X-ray fluorescence (XRF, X-Ray Absorption Near Edge Spectroscopy (XANES, thermal analysis (DTA/TGA, dilatometry (DIL, and chemical analysis. Mineralogical and morphological characteristics of the mineral are presented. The kaolin sample was formed mainly by kaolinite, but other minor phases were also detected such as quartz, cristobalite, tridymite, and dolomite. The high content of volcanic glass detected, by optical microscopy, revealed an incomplete kaolinization process of the raw material. The reddish color of the kaolin was associated with the free iron content in the form of limonite [FeO(OH], which was determined by XANES. The influence of the particle size on the whiteness of kaolin was evaluated. Dilatometric analysis revealed a strong thermal expansion between 110 y 240 °C, which would difficult the use of this material in traditional ceramic applications. On the other hand the presence of glass and high temperature phases of SiO2, such as cristobalite and tridymite will favor its use in the cement industry.El caolín obtenido de Villa de Reyes, una región cercana a San Luis Potosí, México, fue caracterizado por las siguientes técnicas: difracción de rayos-X en polvos (DRX, microscopía óptica (MO, microscopía electrónica de barrido (MEB, fluorescencia de rayos-X (FRX, espectroscopía de absorción de rayos-X (XANES, análisis térmico (DTA/TGA, dilatometría (DIL y análisis químico. Los resultados del análisis mineralógico mediante DRX mostraron un mineral constituido principalmente de caolinita, con una contribución minoritaria de cuarzo, cristobalita, tridimita y dolomita. El análisis por microscopía óptica reveló un alto contenido de material amorfo volcánico, indicando una caolinización incompleta del material v

Synthesis of type A zeolite from calcinated kaolin

International Nuclear Information System (INIS)

Rodrigues, E.C.; Neves, R.F.; Souza, J.A.S.; Moraes, C.G.; Macedo, E.N.

2011-01-01

The mineral production has caused great concern in environmental and industrial scenario due to the effects caused to the environment. The industries of processing kaolin for paper are important economically for the state of Para, but produce huge quantities of tailings, which depend on large areas to be stocked. This material is rich in silico-aluminates can be recycled and used as raw material for other industries. The objective is to synthesize zeolite A at different temperatures of calcination and synthesis. The starting materials and synthesis of zeolite A have been identified and characterized through analysis of X-ray diffraction (DRX) and scanning electron microscopy (MEV). The synthesis process of zeolite A, using as source of silica and the aluminum metakaolin, which was calcined at temperatures of 700 ° C and 800 ° C for 2 hours of landing in a burning furnace type muffle. Observed in relation to the calcination of kaolin as the main phase, the metakaolin. This is just a removal of water from its structure, so we opted for the lower temperature, less energy consumption. The synthesis process of zeolite A, produced good results for the formation of zeolites type A, which were characterized with high purities. (author)

Facile Fabrication of a Hierarchical Superhydrophobic Coating with Aluminate Coupling Agent Modified Kaolin

Directory of Open Access Journals (Sweden)

Hui Li

2013-01-01

Full Text Available A superhydrophobic coating was fabricated from the dispersion of unmodified kaolin particles and aluminate coupling agent in anhydrous ethanol. Through surface modification, water contact angle of the coating prepared by modified kaolin particles increased dramatically from 0° to 152°, and the sliding angle decreased from 90° to 3°. Scanning electron microscopy was used to examine the surface morphology. A structure composed of micro-nano hierarchical component, combined with the surface modification by aluminate coupling agent which reduced the surface energy greatly, was found to be responsible for the superhydrophobicity. The method adopted is relatively simple, facile, and cost-effective and can potentially be applied to large water-repellent surface coatings.

Study of the effect of Kaolin in the mortar of cement matrices by confinement of ion exchange resins

Directory of Open Access Journals (Sweden)

Labied S.

2018-01-01

Full Text Available Radioactive waste arising as a result of nuclear activities should be safely managed from its generation to final disposal in an appropriate conditioned form to reduce the risk of radiation exposure of technical personnel and of the public and to limit contamination of the environment. The immobilization of low and intermediate level radioactive wastes in cementitious matrices is the most commonly used technique to produce inexpensive waste matrix that complies with regulatory requirements in order to protect humans and the environment against nuisance caused by ionizing radiation. Cement based materials are used in radioactive waste management to produce stable waste forms. This matrix constitutes the first build engineering barrier in disposal facilities. In this work, the kaolin is used to enhance the mechanical performance of the matrix of confinement of ion exchange resins by gradually replacing the sand in mortar with kaolin clay. The Kaolin clay sample was a special pure product, sourced from a foreign country. The maximum quantity of resins that can be incorporated into the mortar formulation without the packages losing their strength is 13.915% which results in a better mechanical strength at 6.7686 MPA compression with kaolin.

Effects of Melatonin on the Cerebellum of Infant Rat Following Kaolin-Induced Hydrocephalus: a Histochemical and Immunohistochemical Study.

Science.gov (United States)

Uyanıkgil, Yiğit; Turgut, Mehmet; Baka, Meral

2017-02-01

Hydrocephalus is a developmental disorder causing abnormally collected cerebrospinal fluid within the cerebral ventricles. It leads to bigger skulls and many dysfunctions related to the nervous system. Here, we addressed whether exogenous melatonin administration could reverse the clinical features of kaolin-induced hydrocephalus in infantile rats. A controlled double-blinded study was conducted in 2-week-old 45 Wistar albino rats, which were divided into three groups: Group A, the control group, received intracisternal sham injection with solely the needle insertion; group B, the hydrocephalus group, was treated with isotonic NaCl after kaolin injection; and group C, the hydrocephalus + melatonin group, was given i.p. exogenous melatonin at a dose of 0.5 mg/100 g body weight after kaolin injection. Histological and immunohistochemical analyses were performed after the induction of hydrocephalus and melatonin administration. Glial fibrillary acidic protein was stained by immunohistochemical method. TUNEL method was used to define and quantitate apoptosis in the cerebellar tissues. Statistical analysis was performed by nonparametric Kruskal-Wallis H test, and once significance was determined among means, post hoc pairwise comparisons were carried out using Mann-Whitney U test. We found that melatonin administration significantly ameliorated ratio of substantia grisea area/substantia alba area in the cerebellum of infantile rats. Histologically, there was a significant reduction in the number of cerebellar apoptotic cells after the hydrocephalus induced by kaolin (P cerebellum were reversed by systemic melatonin administration in infantile rats with kaolin-induced hydrocephalus. Nevertheless, further studies are needed to suggest melatonin as a candidate protective drug in children with hydrocephalus.

Long-Chain Diacrylate Crosslinkers and Use of PEG Crosslinks in Poly(potassium acrylate-acrylic acid)/Kaolin Composite Superabsorbents

OpenAIRE

Koroush Kabiri; Siavash Nafisi; Mohammad jalaledin Zohuriaan-Mehr; Ali Akbar Yousefi

2013-01-01

Long-chain diacrylate crosslinkers based on linear α,ω-diols were synthesized and characterized using FTIR and 1H NMR spectroscopy. The highest reaction yield (99.5%) was due to polyethylene glycol diacrylate 1000 (PEGDA-1000). Then, kaolin-containing poly(potassium acrylate-acrylic acid) superabsorbent composites and kaolin-free counterparts were synthesized using PEGDA-1000.The effect of the crosslinker concentration on swelling, rheological and thermo-mechanical properties was investigated...

Synthesis of kaolin supported nanoscale zero-valent iron and its degradation mechanism of Direct Fast Black G in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Jin, Xiaoying; Chen, Zhengxian [Fujian Key Laboratory of Pollution Control and Resource Reuse, School of Environmental Science and Engineering, Fujian Normal University, Fuzhou 350007, Fujian Province (China); Zhou, Rongbing [Institute of Environ Sci and Engineering, Hangzhou Dianzi University, Hangzhou, Zhejiang 310018 (China); Chen, Zuliang, E-mail: Zuliang.chen@unisa.edu.au [Fujian Key Laboratory of Pollution Control and Resource Reuse, School of Environmental Science and Engineering, Fujian Normal University, Fuzhou 350007, Fujian Province (China); Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes, SA 5095 (Australia)

2015-01-15

Graphical abstract: UV–visible spectra of DFBG solution using K-nZVI (1:1) nanoparticles. (a) Before reaction; (b) during reaction; (c) after reaction. - Highlights: • Kaolin-supported Fe{sup 0} nanoparticle (K-nZVI) was synthesized. • Degradation of Direct Fast Black by K-nZVI was studied. • K-nZVI was characterized by SEM, XRD, UV and FIIR. • Degradation mechanism of Direct Fast Black was proposed. - Abstract: Calcinated kaolin supported nanoscale zero-valent iron (K-nZVI) was synthesized and used for the removal of tetrad azo-group dye-Direct Fast Black G (DFBG) from aqueous solution. The results demonstrated that after reacting for 10 min with an initial concentration of DFBG 100 mg L{sup −1} (pH 9.49), 78.60% of DFBG was removed using K-nZVI, while only 41.39% and 12.56% of DFBG were removed using nZVI and kaolin, respectively. K-nZVI with a mass ratio of nZVI nanoparticles versus kaolin at 1:1 was found to have a high degree of reactivity. Furthermore, scanning electron microscopy (SEM) confirmed that nZVI was better dispersed when kaolin was present. XRD patterns indicated that iron oxides were formed after reaction. Fourier transforms infrared spectra (FTIR) and UV–visible demonstrated that the peak in the visible light region of DFBG was degraded and new bands were observed. Kinetics studies showed that the degradation of DFBG fitted well to the pseudo first-order model. The degradation of DFBG by K-nZVI was based on its adsorption onto kaolin and iron oxides, and subsequently reduction using nZVI was proposed. A significant outcome emerged in that 99.84% of DFBG in wastewater was removed using K-nZVI after reacting for 60 min.

Synthesis of kaolin supported nanoscale zero-valent iron and its degradation mechanism of Direct Fast Black G in aqueous solution

International Nuclear Information System (INIS)

Jin, Xiaoying; Chen, Zhengxian; Zhou, Rongbing; Chen, Zuliang

2015-01-01

Graphical abstract: UV–visible spectra of DFBG solution using K-nZVI (1:1) nanoparticles. (a) Before reaction; (b) during reaction; (c) after reaction. - Highlights: • Kaolin-supported Fe 0 nanoparticle (K-nZVI) was synthesized. • Degradation of Direct Fast Black by K-nZVI was studied. • K-nZVI was characterized by SEM, XRD, UV and FIIR. • Degradation mechanism of Direct Fast Black was proposed. - Abstract: Calcinated kaolin supported nanoscale zero-valent iron (K-nZVI) was synthesized and used for the removal of tetrad azo-group dye-Direct Fast Black G (DFBG) from aqueous solution. The results demonstrated that after reacting for 10 min with an initial concentration of DFBG 100 mg L −1 (pH 9.49), 78.60% of DFBG was removed using K-nZVI, while only 41.39% and 12.56% of DFBG were removed using nZVI and kaolin, respectively. K-nZVI with a mass ratio of nZVI nanoparticles versus kaolin at 1:1 was found to have a high degree of reactivity. Furthermore, scanning electron microscopy (SEM) confirmed that nZVI was better dispersed when kaolin was present. XRD patterns indicated that iron oxides were formed after reaction. Fourier transforms infrared spectra (FTIR) and UV–visible demonstrated that the peak in the visible light region of DFBG was degraded and new bands were observed. Kinetics studies showed that the degradation of DFBG fitted well to the pseudo first-order model. The degradation of DFBG by K-nZVI was based on its adsorption onto kaolin and iron oxides, and subsequently reduction using nZVI was proposed. A significant outcome emerged in that 99.84% of DFBG in wastewater was removed using K-nZVI after reacting for 60 min

Physico-Chemical Properties of Kaolin-Organic Acid

Directory of Open Access Journals (Sweden)

Yeo S.W.

2017-01-01

Full Text Available Soil with more than 20% of organic content is classified as organic soil in Malaysia. Contents of organic soil consist of different types of organic and inorganic matter. Each type of organic matter has its own characteristic and its effect on the properties of the soil is different. Hence, a good understanding on the effect of specific organic and inorganic matter on the physico-chemical characteristic of organic soils can serve as a guide for predicting the properties of organic soils. The main objective is to unveil the effect of organic acid on the physico-chemical properties of soil. Artificial organic soil (kaolin mixed with organic acid was utilized in order to minimize the geochemical variability of studied soil. The organic acid which consists of humic acid and fulvic acid was extracted from highly humificated plant–based compost. The effect of organic acid on the physico-chemical properties of soil was determined by varying the concentration of organic acid. The specific gravity, Atterberg limits, pH, bulk chemical composition and the functional group of kaolin-organic acid were determined. It was found that the plasticity index, specific gravity and pH value were decreased with lowered concentration of organic acid. However, the liquid limits and plastic limits were found to be increased with the concentration decrement of organic acid. The analysis of XRF on the bulk chemical composition and analysis of FTIR spectra on the functional group of artificial organic soils with different concentration have confirmed little geochemical variability between samples.

Synthesis of Zeolite A from Kaolin (Shwe Taung Clay)

International Nuclear Information System (INIS)

Mie Mie Han Htun; Mu Mu Htay

2010-12-01

The synthesis of Zeolite A from locally available kaolin clay (Shwe Taung) in Myanmar has been attempted. The kaolinite was converted to metakaoli, by treating with NaOH at 820C for 1hr, and hydrothermal treatment.It was found that the solution of fused clay powder can be crystallized at 100C under ambient pressure to synthesize Zeolite A. The process variables for synthesis have been optimized in order to produce Zeolite A at a lower price. The mole ratio of SiO2/Al2O3 for kaolin was fixed at 2.54. The effects of various factors (aging time and agitation time) on the structure of the sample were extensively investigated. The Shwe Taung clay was characterized by X-ray Diffraction (XRD), X-ray fluorescence (XRF) and Scanning Electron Microscopy (SEM). The samples were characterized by XRD. The results show that the pure form Zeolite A can be prepared with a molar composition of (2.54 SiO3: Al2O3: 5.8Na2O: 256 H2O) by agitation at room temperature for 30min. The mixture was aged for 24 hour at the same temperature and crystallized at 100C for 48 hour.

Characterization of kaolin dispersion using acoustic and electroacoustic spectroscopy

OpenAIRE

Dohnalová Ž.; Svoboda L.; Šulcová P.

2008-01-01

The objective of this work is the investigation of the kaolin dispersion by the ultrasonic techniques. In contact with aqueous solution clay minerals show cation - exchange properties and certain degree of dissolution or rather selective leaching of components. The work is divided into two main parts - determination of zeta potential and particle size distribution. The first part is focused on measuring of zeta potential. Effects of concentration of solid, different kind of electrolytes (0.01...

Feasible synthesis of TiO2 deposited on kaolin for photocatalytic applications

Czech Academy of Sciences Publication Activity Database

Henych, Jiří; Štengl, Václav

2013-01-01

Roč. 61, 3-4 (2013), s. 165-176 ISSN 0009-8604 R&D Projects: GA MPO FR-TI1/006 Institutional support: RVO:61388980 Keywords : Homogeneous Hydrolysis * Kaolin * Photocatalysis * TiO2 * Urea Subject RIV: CA - Inorganic Chemistry Impact factor: 1.398, year: 2013

Elaboration and characterization of mullite-anorthite-albite porous ceramics prepared from Algerian kaolin

International Nuclear Information System (INIS)

Rouabhia, F.; Nemamcha, A.; Moumeni, H.

2018-01-01

Mullite-anorthite-albite porous ceramic materials were successfully prepared by a solid-state reaction between kaolin clay and two different additives (CaCO 3 and Na 2 CO 3 ). The starting raw material was characterized by X-ray fluorescence, X-ray diffraction (XRD) and dynamic light scattering techniques. The effect of CaCO 3 and Na 2 CO 3 concentration (10 to 70 wt%) on structure, morphology and thermal properties of the obtained ceramics was investigated by XRD, scanning electron microscopy and differential scanning calorimetry (DSC) techniques. The XRD patterns showed that mullite (3Al 2 O 3 .2SiO 2 ), anorthite (CaO.Al 2 O 3 .2SiO 2 ) and albite (Na 2 O.Al 2 O 3 .6SiO 2 ) were the main crystalline phases present in the materials. The morphology investigation revealed the porous texture of obtained ceramics characterized by the presence of sponge-like structure mainly due to the additive decomposition at high temperatures. The DSC results confirm the presence of four temperature regions related to the kaolin thermal transformations and the formation of minerals. The temperature and enthalpy of mineral formation are additive concentration dependent. As a result, the optimal content of additives which allowed the coexistence of the three phases, a spongelike morphology, and high porosity without cracks corresponded to 15 wt% CaCO 3 , 15 wt% Na 2 CO 3 , and 70 wt% kaolin. (author)

Synthesis of microporous material faujasite-type from kaolin waste; Sintese de material microporoso do tipo faujasita a partir de rejeito de caulim

Energy Technology Data Exchange (ETDEWEB)

Hildebrando, E.A.; Valenzuela-Diaz, F.R., E-mail: edemarino@usp.b [Universidade de Sao Paulo (USP), SP (Brazil). Dept. de Engenharia Metalurgica e de Materiais. Lab. de Materias-Primas Particuladas e Solidos nao Metalicos; Angelica, R.S. [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Inst. de Geociencias. Fac. de Geologia; Neves, R.F. [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Inst. de Tecnologia. Fac. de Engenharia Quimica

2010-07-01

Zeolite with structure faujasite was synthesized using kaolin waste from kaolin processing industries for paper coating as predominant source of silicon and aluminum; the starting material was characterized by XRF, XRD, DTA/TG, SEM, and products obtained by XRD and SEM. Synthesis in hydrothermal conditions occurred on autoclave and time-temperature effects, as well as the relationship Si/Al were considered. The results show that the methodology developed with the waste of calcined kaolin reacting at 90 deg C for 20 hours in an alkaline medium, in the presence of an additional source of silica was obtained zeolite Y as single phase present in the product. (author)

Comparing Kaolin and Pinolene to Improve Sustainable Grapevine Production during Drought.

Science.gov (United States)

Brillante, Luca; Belfiore, Nicola; Gaiotti, Federica; Lovat, Lorenzo; Sansone, Luigi; Poni, Stefano; Tomasi, Diego

2016-01-01

Viticulture is widely practiced in dry regions, where the grapevine is greatly exposed to water stress. Optimizing plant water use efficiency (WUE) without affecting crop yield, grape and wine quality is crucial to limiting use of water for irrigation and to significantly improving viticulture sustainability. This study examines the use in vineyards of particle film technology (engineered kaolin) and compares it to a film-forming antitranspirant (pinolene), traditionally used to limit leaf water loss, and to an untreated control. The trial was carried out under field conditions over three growing seasons, during which moderate to very severe plant water stress (down to -1.9 MPa) was measured through stem water potential. Leaf stomatal conductance (gs) and photosynthesis rate (An) were measured during the seasons and used to compute intrinsic WUE (WUEi, defined as An/gs ratio). Leaf temperature was also recorded and compared between treatments. Bunch quantity, bunch and berry weight, sugar accumulation, anthocyanin and flavonoid contents were measured. Finally, microvinifications were performed and resultant wines subjected to sensory evaluation.Results showed that the use of kaolin increased grapevine intrinsic WUE (+18% on average as compared to unsprayed vines) without affecting berry and bunch weight and quantity, or sugar level. Anthocyanin content increased (+35%) in kaolin treatment, and the wine was judged more attractive (p-value wine was the least appreciated. This study demonstrates that particle film technology can improve vine WUEi and wine quality at the same time, while traditional antitranspirants were not as effective for these purposes. This positive effect can be used in interaction with other already-demonstrated uses of particle film technology, such as pest control and sunburn reduction, in order to achieve more sustainable vineyard management.

Fire performance of fiber board coated with nano kaolin-clay film

Science.gov (United States)

Zhijia Liu; John F. Hunt; Zhiyong Cai

2013-01-01

Fiberboard is a common interior material used both in China and the United States of America. The increase in demand for interior materials has raised concerns regarding combustibility of the materials. The pyrolysis characteristics of fiber, phenolic resin (PF), and nano kaolin-clay (NK) were investigated using thermogravimetry. The fire performances of samples coated...

Investigation on the effect of sintering temperature on kaolin hollow fibre membrane for dye filtration.

Science.gov (United States)

Mohtor, Nur Hamizah; Othman, Mohd Hafiz Dzarfan; Ismail, Ahmad Fauzi; Rahman, Mukhlis A; Jaafar, Juhana; Hashim, Nur Awanis

2017-07-01

Despite its extraordinary price, ceramic membrane can still be able to surpass polymeric membrane in the applications that require high temperature and pressure conditions, as well as harsh chemical environment. In order to alleviate the high cost of ceramic material that still becomes one of the major factors that contributes to the high production cost of ceramic membrane, various attempts have been made to use low cost ceramic materials as alternatives to well-known expensive ceramic materials such as alumina, silica, and zirconia in the fabrication of ceramic membrane. Thus, local Malaysian kaolin has been chosen as the ceramic material in this study for the preparation of kaolin hollow fibre membrane since it is inexpensive and naturally abundant in Malaysia. Due to the fact that the sintering process plays a prominent role in obtaining the desired morphology, properties, and performances of prepared ceramic membrane, the aim of this work was to study the effect of different sintering temperatures applied (ranging from 1200 to 1500 °C) in the preparation of kaolin hollow fibre membrane via dry/wet phase inversion-based spinning technique and sintering process. The morphology and properties of membrane were then characterised by SEM, AFM, FTIR, XRD, and three-point bending test, while the performances of membrane were investigated by conducting water permeation and Reactive Black 5 (RB5) dye rejection tests. From the experimental results obtained, the sintering temperature of 1400 °C could be selected as the optimum sintering temperature in preparing the kaolin hollow fibre membrane with the dense sponge-like structure of separation layer that resulted in the good mechanical strength of 70 MPa with the appreciable water permeation of 75 L/h m 2  bar and RB5 rejection of 68%.

Thermodynamic analysis of stability in iron removal from kaolin by using oxalic acid

Directory of Open Access Journals (Sweden)

C. Ocampo-López

2013-06-01

Full Text Available The graphical representation of global stability for a system, or Pourbaix diagram, was constructed to perform a thermodynamic study of iron removal from kaolin using oxalic acid as an oxidant. To do this the free energies of formation of the oxalate complex of the system were calculated, and it was found that the more stable specie is Fe(C2O43-3, with a calculated free energy of formation of -3753.88 kcal/mol. Thermodynamic stability functions were estimated for the system as a function of pH and Eh known as potential of oxide reduction. It was built a global stability diagram for the removal system; it showed that the specie trioxalate Fe(C2O43-3 is the only oxalate in equilibrium with other compounds associated with the removal of iron in kaolin.

Synthesis and characterization of mangan oxide coated sand from Capkala kaolin

Science.gov (United States)

Destiarti, Lia; Wahyuni, Nelly; Prawatya, Yopa Eka; Sasri, Risya

2017-03-01

Synthesis and characterization of mangan oxide coated sand from quartz sand fraction of Capkala kaolin has been conducted. There were two methods on synthesis of Mangan Oxide Coated Sand (MOCS) from Capkala Kaolin compared in this research. Characterization of MOCS was done by using Scanning Electron Microscope/Energy Dispersive X-Ray Spectrometer (SEM/EDX) and X-Ray Diffraction (XRD). The MOCS was tested to reduce phosphate in laundry waste. The result showed that the natural sand had bigger agregates and a relatively uniform structural orientation while both MOCS had heterogen structural orientation and manganese oxide formed in cluster. Manganese in first and second methods were 1,93% and 2,63%, respectively. The XRD spectrum showed clear reflections at 22,80°, 36,04°, 37,60° and a broad band at 26,62° (SiO2). Based on XRD spectrum, it can be concluded that mineral constituents of MOCS was verified corresponding to pyrolusite (MnO2). The former MOCS could reduce almost 60% while the later could reduce 70% phosphate in laundry waste.

Characterization of kaolin and granite waste for formulation of porcelain stoneware tiles

International Nuclear Information System (INIS)

Luna da Silveira, G.C.; Acchar, W.; Gomes, U.U.; Silva, B.K.O.; Luna da Silveira, R.V.; Labrincha, J.A.; Costa, M.C.P.

2016-01-01

To produce a stoneware tiles is necessary develop a formulation that satisfies their structural characteristics, micro-structural, physical and mechanical properties. Thus, in order to create a formulation for porcelain stoneware tiles that give use to kaolin and granite waste used in the production of ceramic materials were asked the following characterizations: chemical analysis, mineralogical, thermal and particle size. We found that in the kaolin sample it presents a rate of silicon oxide and aluminum oxide similar to those found in the work of other investigators, about 45.23% SiO2 and 37.39% Al_2O_3. In the granite waste, the percentage of silicon oxide and aluminum oxide are also similar to those observed in other studies, with about 74.89% SiO2 and 10.54% Al_2O_3. Both the percentage of SiO_2 and Al_2O_3 founded in these two samples satisfy the percentage required in the manufacturing of porcelain stoneware tiles. (author)

New organophilic kaolin clays based on single-point grafted 3-aminopropyl dimethylethoxysilane.

Science.gov (United States)

Zaharia, A; Perrin, F-X; Teodorescu, M; Radu, A-L; Iordache, T-V; Florea, A-M; Donescu, D; Sarbu, A

2015-10-14

In this study, the organophilization procedure of kaolin rocks with a monofunctional ethoxysilane- 3 aminopropyl dimethyl ethoxysilane (APMS) is depicted for the first time. The two-step organophilization procedure, including dimethyl sulfoxide intercalation and APMS grafting onto the inner hydroxyl surface of kaolinite (the mineral) layers was tested for three sources of kaolin rocks (KR, KC and KD) with various morphologies and kaolinite compositions. The load of APMS in the kaolinite interlayer space was higher than that of 3-aminopropyl triethoxysilane (APTS) due to the single-point grafting nature of the organophilization reaction. A higher long-distance order of kaolinite layers with low staking was obtained for the APMS, due to a more controllable organiphilization reaction. Last but not least, the solid state (29)Si-NMR tests confirmed the single-point grafting mechanism of APMS, corroborating monodentate fixation on the kaolinite hydroxyl facets, with no contribution to the bidentate or tridentate fixation as observed for APTS.

Control of the Mexican bean weevil Zabrotes subfasciatus with kaolin Controle do caruncho-do-feijão Zabrotes subfasciatus com caulim

Directory of Open Access Journals (Sweden)

Adriana Yatie Mikami

2010-07-01

Full Text Available The Mexican bean weevil Zabrotes subfasciatus (Coleoptera: Chrysomelidae: Bruchinae is an important pest of stored beans in tropical regions. The efficiency of kaolin [with or without neem (Azadirachta indica oil] and diatomaceous earth (DE (standard treatment was studied in laboratory aiming to obtain alternatives for chemical control of this insect. Insects were confined in plastic vials containing beans treated with kaolin (2, 4 and 8g kg-1, kaolin + neem [2g kg-1(5% neem oil], diatomaceous earth (1g kg-1 and control. Mortality of adult insects, number of eggs and F1generation beetles emergency were assessed. Kaolin caused mortality of Z. subfasciatus, however higher periods and doses than DE were necessary to promote high mortality (100% or close. Kaolin treatments also affected female behavior because many eggs were placed in the vials walls. Number of emerged adults (F1 was similar between DE and kaolin; hence, kaolin constitutes a promising tool to the management of Z. subfasciatus. The mixture of kaolin and neem oil was not efficient in the control of Z. subfasciatus.O caruncho-do-feijão Zabrotes subfasciatus (Coleoptera: Chrysomelidae: Bruchinae é uma importante praga de grãos de feijão armazenado nas regiões tropicais. A eficiência do caulim [com ou sem óleo de nim (Azadirachta indica] e terra diatomácea (TD (tratamento padrão foi estudada em laboratório com o intuito de obter alternativas para o controle químico deste inseto. Insetos foram confinados em frascos de plástico com feijão tratado com caulim (2, 4 e 8g kg-1, caulim + nim [2g kg-1(5% óleo de nim], terra diatomácea (1g kg-1 e controle. Mortalidade de insetos adultos, número de ovos e emergência da geração F1 foram avaliados. Caulim causou a mortalidade de Z. subfasciatus, porém foram necessários maiores períodos e doses que a TD para promover elevada mortalidade (100% ou aproximadamente. Os tratamentos com caulim também afetaram o comportamento da f

Use of kaolin as a potential low-cost adsorbent for the removal of malachite green from colored effluents

Energy Technology Data Exchange (ETDEWEB)

Foletto, E.L.; Caponi, N.; Collazzo, G.C.; Jahn, S.L.; Dotto, G.L.; Mazutti, M.A. [Universidade Federal de Santa Maria (UFSM), RS (Brazil)

2016-07-01

Full text: This study investigated the potential of raw kaolin as a low-cost adsorbent for the removal Malachite Green (MG) from colored effluents. The morphology, chemical structure and the surface properties of the adsorbent were investigated by characterization techniques such as X-ray diffraction, N2 adsorption-desorption isotherms, Fourier transform infrared spectroscopy, X-ray fluorescence spectroscopy and scanning electron microscopy. A possible technological application of kaolin is the MG removal from aqueous media, which was investigated by batch adsorption experiments. The adsorption kinetics was studied using the pseudo-first order, pseudo-second order and Elovich models. The adsorption isotherms were studied using Langmuir, Freundlich and Sips models. Maximum adsorption capacity was found to be 128 mg g-1, and this satisfactory result may be associated to some properties of adsorbent. Therefore, the results of this investigation revealed that kaolin can be utilized as a promising low-cost adsorbent to remove MG from colored effluents. (author)

An evaluation of soluble cations and anions on the conductivity and rate of flocculation of kaolins

Science.gov (United States)

Fulton, Deborah Lee

1998-10-01

The focus of this project was to learn how ionic concentrations and their contributions to electric conductivity influence the flocculation behavior of kaolin/water suspensions. Sodium silicate, calcium chloride, and magnesium sulfate were used as chemical additives. The specific surface areas, particle size distributions, and methylene blue indices for two kaolins were measured. The SSA and MBI for these kaolins indicated that they possessed inherent differences in SSA and flocculation behaviors. Rheological studies were also performed. Testing included simultaneous gelation, deflocculation, and pH tests. Viscosity, pH, temperature, and chemical additive concentrations were monitored at each point. Testing was performed at 45/55 wt% solids. Effects of additions of various levels of deflocculant and flocculant to each of the kaolin/water suspensions were studied by making several suspensions from each kaolin. The concentrations of dispersant, and flocculant levels and types were varied to produce suspensions with different chemical additive "histories," but all with similar final apparent viscosities. Slurry filtrates were analyzed for conductivity, pH, temperature, and ion concentrations of (Al3+, Fe2+,3+, Ca 2+, Mg+, Na+, SO4 2--, and Cl--). Plastic properties were calculated to determine how variations in suspension histories affected conductivities, pH, and detectable ion contents of the suspensions. These analyses were performed on starting slurries which were under-, completely-, and over-deflocculated before further additions of flocculants and deflocculant were added to tune the slurries to the final, constant, target viscosity. Results showed that rates of flocculation and conductivities increased as concentrations of ions increased. By increasing conductivity correlations with increases in flocculation occurs, which yields higher rates of buildup, or RBU [1]. This is the single most important slip control property in the whitewares industry. Shear

Correlation between hardness and water absorption properties of Saudi kaolin and white clay geopolymer coating

Science.gov (United States)

Ramasamy, Shamala; Abdullah, Mohd Mustafa Al Bakri; Huang, Yue; Hussin, Kamarudin; Wang, Jin; Shahedan, Noor Fifinatasha

2017-09-01

Geopolymer is an uprising technology that is being studied worldwide. Geopolymer raw materials are basically aluminosilicate source materials. However, this technology is yet to infiltrate into pipelines and coating industries which initiated our research idea. The idea of creating universal geopolymer based coating material is mainly to help oil and gas industry reduce its maintenance cost. Kaolin based geopolymer paste was coated on glass reinforced epoxy (GRE) substrates which are majorly used as pipeline material in the oil and gas industry at Saudi Arabia. Kaolin and white clay was chosen as raw material to study the possibilities of utilizing underused aluminosilicate raw materials for geopolymer coating. To obtain suitable formulation, Na2SiO3/NaOH ratio was varied from 0.40 untill 0.60 while other parameters such as solid/liquid ratio and NaOH molarity were kept constant at values as per previous works. Geopolymer coated GRE substrates were then subjected to water absorption, flexural strength and hardness test to validate our findings. Water absorption is a crucial test as for coating materials which justifies the pratical usability of the coating product. Upon testing, kaolin and white clay based geopolymer coating each shows promising properties at Na2SiO3/NaOH ratio of 0.45 and 0.50 each.

Uranium in mining water of kaolin open pit in Zarów (Lower Silesia); methodology of determination and genetic remarks.

Science.gov (United States)

Chau, N D; Wyszomirski, P; Chruściel, E; Ochoński, A

1999-11-01

In this paper, a method of determination of uranium 238 and 234 in mining waters of Andrzej kaolin open pit in Zarów (Lower Silesia) is presented. The method is based on independent measurements of alpha and beta radiation intensities by means of a liquid scintillation spectrometer alpha/beta. The initial volume of water sample was 3 dm3, then it was diminished by chemical preparation to 6 cm3, and then 12 cm3 of scintillator was added. The lower limit of detection (for the measurement time of 8 h) for both 234U and 238U amounted to 0.02 Bq/dm3. For determination of the uranium content in ferruginous sediments precipitating from mining waters of the above-mentioned open pit, gamma ray spectrometry was used. The obtained results may be viewed as a contribution to studies on anomalous uranium concentration within this kaolin deposit. The elevated uranium content, in comparison with its average concentration in the Earth crust, is characteristic for parent rocks of Andrzej kaolin deposit, which are granitoids of Strzegom-Sobótka massif. In connection with it, the high uranium content can be observed not only in kaolin and weakly kaolinised granitoids from the deposit in question, but also in mining waters genetically related with them.

Effects of using kaolin waste and granite waste as raw materials for the production of low-water absorption ceramic tiles

International Nuclear Information System (INIS)

Freires, H.P.; Argonz, R.; Nogueira, R.E.F.Q.; Sasaki, J.M.; Sales, J.C.

2012-01-01

This study aims to evaluate the potential of co-use of granite waste (Rain Forest) and kaolin waste as raw material for the manufacture of ceramic coating of low water absorption. Raw materials were characterized by X-ray diffraction. Kaolin residue was added to the residue of granite in the following proportions (in wt%): 0, 10, 20, 30, 40 and 50%. Specimens were fabricated by uniaxial pressing and fired at 1175,1200 and 1225 deg C. Studies of firing linear shrinkage, water absorption, apparent porosity, apparent density and tensile bending test (or rupture modulus) were conducted. The temperature of 1225 deg C allowed the use of a mixture of 50% granite residue and 50% kaolin residue. Ceramic parts made from that mixture exhibited the maximum values required by the Brazilian Standard NBR 13818 for water absorption, shrinkage and density. (author)

Influence of Kaolin in Fly Ash Based Geopolymer Concrete: Destructive and Non-Destructive Testing

Science.gov (United States)

Yahya, Z.; Abdullah, M. M. A. B.; Ramli, N. Mohd; Burduhos-Nergis, D. D.; Razak, R. Abd

2018-06-01

Development of geopolymer concrete is mainly to reduce the production of ordinary Portland cement (OPC) that adverse the natural effect. Fly ash is a by-product collected from electrical generating power plant which resulted from burning pulverized coal. Since fly ash is waste materials, it can be recycled for future advantages particularly as pozzolanic materials in construction industry. This study focused on the feasibility of fly ash based geopolymer concrete to which kaolin has been added. The main constituents of geopolymer production for this study were class F fly ash, sodium silicate and sodium hydroxide (NaOH) solution. The concentration of NaOH solution was fixed at 12 Molar, ratio of fly ash/alkaline activator and sodium silicate/NaOH fixed at 1.5 and 2.5, respectively. Kaolin was added in range 5% to 15% from the mass of fly ash and all the samples were cured at room temperature. Destructive and non-destructive test were performed on geopolymer concrete to evaluate the best mix proportions that yield the highest strength as well as the quality of the concrete. Compressive strength, flexural strength, rebound hammer and ultrasonic pulse velocity (UPV) result have been obtained. It shown that 5% replacement of kaolin contributed to maximum compressive strength and flexural strength of 40.4 MPa and 12.35 MPa at 28 days. These result was supported by non-destructive test for the same mix proportion.

Application Of Bacterial Iron Reduction For The Removal Of Iron Impurities From Industrial Silica Sand And Kaolin

Science.gov (United States)

Zegeye, A.; Yahaya, S.; Fialips, C. I.; White, M.; Manning, D. A.; Gray, N.

2008-12-01

Biogeochemical evidence exists to support the potential importance of crystalline or amorphous Fe minerals as electron acceptor for Fe reducing bacteria in soils and subsurface sediments. This microbial metabolic activity can be exploited as alternative method in different industrial applications. For instance, the removal of ferric iron impurities from minerals for the glass and paper industries currently rely on physical and chemical treatments having substantial economical and environmental disadvantages. The ability to remove iron by other means, such as bacterial iron reduction, may reduce costs, allow lower grade material to be mined, and improve the efficiency of mineral processing. Kaolin clay and silica sand are used in a wide range of industrial applications, particularly in paper, ceramics and glass manufacturing. Depending on the geological conditions of deposition, they are often associated with iron (hydr)oxides that are either adsorbed to the mineral surfaces or admixed as separate iron bearing minerals. In this study, we have examined the Fe(III) removal efficiency from kaolin and silica sand by a series of iron- reducing bacteria from the Shewanella species (S. alga BrY, S. oneidensis MR-1, S. putrefaciens CN32 and S. putrefaciens ATCC 8071) in the presence of anthraquinone 2,6 disulfonate (AQDS). We have also investigated the effectiveness of a natural organic matter, extracted with the silica sand, as a substitute to AQDS for enhancing Fe(III) reduction kinetics. The microbial reduction of Fe(III) was achieved using batch cultures under non-growth conditions. The rate and the extent of Fe(III) reduction was monitored as a function of the initial Fe(III) content, Shewanella species and temperature. The bacterially- treated minerals were analyzed by transmission electron microscopy (TEM) and X-ray diffraction (XRD) to observe any textural and mineralogical transformation. The whiteness and ISO brightness of the kaolin was also measured by

Synthesis of zeolite using as precursor reject of kaolin of the Amazon Region: application as an adsorbent in gas drying

International Nuclear Information System (INIS)

Morais, M.R.C.; Santana, D.L. de; Martelli, M.C.; Neves, R.F.

2011-01-01

Zeolites have large variety of technological applications, accounting for an increasing interest in various industries. In the State of Para, located three industries from kaolin for paper, where large amounts of waste are stored in ponds in becoming environmental problem. This work aims to develop a process for obtaining a zeolite P from the kaolin waste as the starting material. The synthesis was performed with kaolin waste from Capim River region, calcined at 700 ° C for 2 h, and reacted in the presence of aqueous NaOH and diatomite (silica source supplement), and the process hydrothermal temperature of 110 ° C for varied times. The characterization of the starting material and the synthesized materials was carried out using XRD and SEM. At the end of the experiment, the zeolite P synthesized was tested for moisture adsorption and was effective for this purpose. (author)

Synthesis and characterization of zeolite NaP using kaolin waste as a source of silicon and aluminum

Energy Technology Data Exchange (ETDEWEB)

Hildebrando, Edemarino Araujo, E-mail: edemarino@ufpa.br [Universidae Federal do Para (UFPA), Maraba, PA (Brazil). Fac. de Engenharia de Materias. Lab. de Materiais Ceramicos; Andrade, Christiano Gianesi Bastos; Valenzuela-Diaz, Francisco Rolando [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Dept. de Metalurgia e Engenharia de Materiais; Rocha Junior, Carlos Augusto Ferreira da; Neves, Roberto de Freitas [Universidae Federal do Para (UFPA), Maraba, PA (Brazil). Int. de Tecnologia. Fac. de Engenharia Quimica; Angelica, Romulo Simoes [Universidae Federal do Para (UFPA), Maraba, PA (Brazil). Inst. de Geociencias. Fac. de Geologia

2014-08-15

The synthesis of zeolite NaP using kaolin waste, from the Amazon region, as a predominant source of silicon and aluminum has been studied. The zeolitisation process occurred in hydrothermal conditions using static autoclaving and the effects of time, temperature, and the Si/Al ratio were investigated. The starting material and the phases formed as reaction products were characterized by XRD, SEM and FTIR. The results showed that pure zeolite NaP is hydrothermally synthesized, at 100 °C for 20 hours, using meta kaolin waste material in alkaline medium in presence of additional silica. The XRD and SEM analyses indicate that the synthesized zeolite presents good crystallinity. (author)

Synthesis and characterization of zeolite NaP using kaolin waste as a source of silicon and aluminum

International Nuclear Information System (INIS)

Hildebrando, Edemarino Araujo; Andrade, Christiano Gianesi Bastos; Valenzuela-Diaz, Francisco Rolando; Rocha Junior, Carlos Augusto Ferreira da; Neves, Roberto de Freitas; Angelica, Romulo Simoes

2014-01-01

The synthesis of zeolite NaP using kaolin waste, from the Amazon region, as a predominant source of silicon and aluminum has been studied. The zeolitisation process occurred in hydrothermal conditions using static autoclaving and the effects of time, temperature, and the Si/Al ratio were investigated. The starting material and the phases formed as reaction products were characterized by XRD, SEM and FTIR. The results showed that pure zeolite NaP is hydrothermally synthesized, at 100 °C for 20 hours, using meta kaolin waste material in alkaline medium in presence of additional silica. The XRD and SEM analyses indicate that the synthesized zeolite presents good crystallinity. (author)

Comparing Kaolin and Pinolene to Improve Sustainable Grapevine Production during Drought.

Directory of Open Access Journals (Sweden)

Luca Brillante

Full Text Available Viticulture is widely practiced in dry regions, where the grapevine is greatly exposed to water stress. Optimizing plant water use efficiency (WUE without affecting crop yield, grape and wine quality is crucial to limiting use of water for irrigation and to significantly improving viticulture sustainability. This study examines the use in vineyards of particle film technology (engineered kaolin and compares it to a film-forming antitranspirant (pinolene, traditionally used to limit leaf water loss, and to an untreated control. The trial was carried out under field conditions over three growing seasons, during which moderate to very severe plant water stress (down to -1.9 MPa was measured through stem water potential. Leaf stomatal conductance (gs and photosynthesis rate (An were measured during the seasons and used to compute intrinsic WUE (WUEi, defined as An/gs ratio. Leaf temperature was also recorded and compared between treatments. Bunch quantity, bunch and berry weight, sugar accumulation, anthocyanin and flavonoid contents were measured. Finally, microvinifications were performed and resultant wines subjected to sensory evaluation.Results showed that the use of kaolin increased grapevine intrinsic WUE (+18% on average as compared to unsprayed vines without affecting berry and bunch weight and quantity, or sugar level. Anthocyanin content increased (+35% in kaolin treatment, and the wine was judged more attractive (p-value <0.05 and slightly more appreciated (p-value < 0.1 than control. Pinolene did not increase WUEi, limiting An more than gs; grapes with this treatment contained lower sugar and anthocyanin content than control, and the obtained wine was the least appreciated. This study demonstrates that particle film technology can improve vine WUEi and wine quality at the same time, while traditional antitranspirants were not as effective for these purposes. This positive effect can be used in interaction with other already

Síntese e caracterização de hidrogéis compósitos a partir de copolímeros acrilamida-acrilato e caulim: efeito da constituição de diferentes caulins do nordeste brasileiro Synthesis and characterization of poly (acrylamide-co-acrylate and kaolin hydrogel composites: effect of the constitution of different kaolins from northeastern Brazil

Directory of Open Access Journals (Sweden)

Carlos W. de Q. Brito

2013-01-01

Full Text Available Superabsorbent hydrogels based on poly (acrylamide-co-acrylate and different kaolins, were prepared by free-radical aqueous copolymerization. FTIR and WAXS techniques were employed for characterization of a series of hydrogels, obtained by varying the percentage of clay, crosslinking and constitution of kaolin. The water absorbency at equilibrium (Weq decreased with increasing clay content and the amount of crosslinking agent. Superabsorbent hydrogel (Weq > 1084 g H2O/g gel was obtained as 10 wt% of white kaolin and 0.05 mol% of crosslinking agent were used. The hydrogel proved sensitive to pH variation and the presence of salts.

Partitioning of hexachlorobenzene in a kaolin/humic acid/surfactant/water system: Combined effect of surfactant and soil organic matter

Energy Technology Data Exchange (ETDEWEB)

Wan, Jinzhong; Wang, Lingling [Environmental Science Research Institute, Huazhong University of Science and Technology, Wuhan 430074 (China); Lu, Xiaohua, E-mail: hust-esri2009@hotmail.com [Environmental Science Research Institute, Huazhong University of Science and Technology, Wuhan 430074 (China); Lin, Yusuo; Zhang, Shengtian [Nanjing Institute of Environmental Science, Ministry of Environmental Protection of China, Nanjing 210042 (China)

2011-11-30

Highlights: Black-Right-Pointing-Pointer We study HCB partitioning in a kaolin/humic acid/TX100/water system. Black-Right-Pointing-Pointer We reveal influence of TX100-HA interaction on TX100 and HA sorption to kaolin. Black-Right-Pointing-Pointer We verify combined effect of TX100 and HA on HCB desorption from clay. - Abstract: Understanding the combined effect of soil organic matter (SOM) and surfactants on the partitioning of hydrophobic organic compounds in soil/water systems is important to predict the effectiveness of surfactant-enhanced remediation (SER). In the present study we investigate the partitioning of hexachlorobenzene (HCB) within a humic acid (HA)-coated kaolin/Triton X-100 (TX100)/water system, with special emphasis on the interaction between TX100 and HA, and their combined effect on HCB sorption. HA firstly enhanced then suppressed TX100 sorption to kaolin as the amounts of HA increased, while the addition of TX100 led to a consistent reduction in HA sorption. In the HA-coated kaolin/TX100/water system, TX100 played a primary role in enhancing desorption of HCB, while the role could be suppressed and then enhanced as HA coating amounts increased. Only at HA coating above 2.4%, dissolved HA outcompeted clay-bound HA for HCB partitioning, resulting in dissolved HA enhanced desorption. The presence of dissolved HA at these conditions further promoted the effectiveness of TX100 enhanced desorption. Despite a reduced TX100 sorption to clay was achieved due to the presence of dissolved HA, the effect on HCB desorption was comparatively slight. A reliable cumulative influence of HA and TX100 on HCB desorption was observed, although HCB desorption by HA/TX100 mixed was less than the sum of HA and TX100 individually. Our study suggests that for soils of high organic contents, the combined effect of SOM and surfactants on HOCs desorption can be applied to improve the performance of SER.

Application of molybdenum and phosphate modified kaolin in electrochemical treatment of paper mill wastewater

International Nuclear Information System (INIS)

Ma Hongzhu; Wang Bo; Wang Ying

2007-01-01

Pulp and paper mill wastewater is characterized by very high chemical oxygen demand (COD) values that inhibit the activity of microorganisms during biological oxidations. The electrochemical degradation of pulp and paper mill wastewater catalyzed by molybdenum and phosphate (Mo-P) modified kaolin with graphite as anode and cathode was investigated. The catalyst was characterized by XRD, XPS and SEM spectra and the effects of pH, metal ion and introduction of NaCl on the efficiency of the electrochemical degradation process were also studied. It was found out that the modified kaolin loaded with Fe 3+ had higher electrochemical catalytic activity in the electrochemical degradation of paper mill wastewater at pH 4. A 96% COD removal efficiency was obtained in 40 min of electrochemical treatment of the wastewater at current density 30 mA cm -2 . A possible mechanism for degradation of the mill wastewater constituents was also proposed

Adsorpce toxických oxoaniontů Se na povrchově upravený kaolin

Czech Academy of Sciences Publication Activity Database

Herzogová, L.; Doušová, B.; Lhotka, M.; Machovič, Vladimír; Schweigstillová, Jana; Koloušek, D.

2012-01-01

Roč. 106, č. 8 (2012), s. 759-764 ISSN 0009-2770 Institutional research plan: CEZ:AV0Z30460519 Keywords : adsorption * oxoanions Se * surface-modified kaolins Subject RIV: CA - Inorganic Chemistry Impact factor: 0.453, year: 2012 http://www.chemicke-listy.cz/docs/full/2012_08_759-764.pdf

Kaolin particle films suppress many apple pests, disrupt natural enemies and promote woolly apple aphid

NARCIS (Netherlands)

Markó, V.; Blommers, L.H.M.; Bogya, S.; Helsen, H.H.M.

2008-01-01

Multiple applications of hydrophobic kaolin particle film in apple orchards suppressed numbers of blossom weevil (Anthonomus pomorum), brown leaf weevil (Phyllobius oblongus), attelabid weevil (Caenorhinus pauxillus), leafhoppers (Empoasca vitis and Zygina flammigera) and green apple aphid (Aphis

Investigation of the effect of kaolin and tissue factor-activated citrated whole blood, on clot forming variables, as evaluated by thromboelastograph

DEFF Research Database (Denmark)

Johansson, Per Ingemar; Bochsen, L.; Andersen, S.

2008-01-01

), and maximum clot strength (amplitude [MA]) were evaluated, together with day-to-day variation, the coefficient of variance (CV%), and the effect of citrate storage time. RESULTS: Clot formation variables were equally affected by TF 1:17,000 and kaolin activation, whereas R was significantly longer when TF 1......:42,500 was used. The CV for the different variables varied from 3 to 13 percent with no significant differences between assays. Storage of citrated WB significantly affected the TEG variables in a hypercoagulable direction. Only the R, however, was significantly affected (12%) when samples rested for 0 and 30...... minutes were evaluated with kaolin as the activator. CONCLUSION: The TEG assays evaluated were reproducible and present with an acceptable CV% for routine clinical practice. Kaolin and TF 1:17,000 equally affected the clot formation variables. Storage of WB for up to 30 minutes in citrate did not, except...

Sample size clay kaolin of primary in pegmatites regions Junco Serido - PB and Equador - RN; Granulometria de argila caulim primario dos pegmatitos nas regioes do Junco do Serido - PB e Equador - RN

Energy Technology Data Exchange (ETDEWEB)

Meyer, M.F.; Sousa, J.B.M.; Sales, L.R.; Silva, P.A.S.; Lima, A.D.D., E-mail: mauro.meyer@ifrn.edu.br [Instituto Federal do Rio Grande do Norte (IFRN), RN (Brazil)

2016-07-01

Kaolin is a clay formed mainly of kaolinite resulting from feldspar weathering or hydrothermal. This study aims to investigate the way of occurrence, kaolin particle size of the pegmatites of the Borborema Province Pegmatitic in the regions of Junco do Serido-PB and Ecuador-RN. These variables were analyzed considering granulometric intervals obtained from wet sieving of samples of pegmatite mines in the region. Kaolin was received using sieves of 200, 325, 400 and 500 mesh and the sieve fractions retained by generating statistical parameters histograms. kaolin particles are extremely fine and pass in its entirety through 500 mesh sieve. The characterization of minerals in fine fractions by diffraction of X-rays showed that the relative amount of sericite in fractions retained in sieves 400 and 500 mesh impairing the whiteness and mineralogical texture kaolin production. (author)

Deposition of waste kaolin in aluminum alloy by electrolytic plasma technique

International Nuclear Information System (INIS)

Palinkas, Fabiola Bergamasco da Silva Marcondes; Antunes, Maria Lucia Pereira; Cruz, Nilson Cristino; Rangel, Elidiane Cipriano; Souza, Jose Antonio da Silva

2016-01-01

Full text: Kaolin is a widely explored mineral for various industrial purposes and its processing generates up to 90% of waste, corresponding to 500 thousand tons annually. The Deposition of Kaolin residue on aluminum alloys by electrolytic plasma has objective of a valorization of the residue. It was evaluated the mineralogical composition by X-ray diffraction (XRD), using PANalytical diffractometer X'Pert Pro. The scanning electron microscopy (SEM) and the spectrometry of dispersive of energy (EDS) evaluated the morphology and elementary chemical composition by microscope scanning electron JEOL JSM-6010LA. The Infrared Spectroscopy (FTIR) has used a Spectrometer the Perkin-Elmer 1760X FT-IR with spectral range 4000-400 cm -1 . XRD results indicate peaks of kaolinite as the main constituent. The morphology of the particles correspond to pseudo-hexagonal lamellar crystals characteristic of kaolinite, analysis by EDS allows to identify the composition of the particles as Al and Si. The samples were deposited at concentrations of 5, 10 and 15 mg of the residue and each concentration were considered deposition times of 5, 10 and 15 minutes. Tests evaluate the films as the wettability, chemical composition, morphology, mechanical strength and corrosion resistance. Results indicate the presence of kaolinite, alumina and mullite in the obtained coatings. (author)

Comparing Kaolin and Pinolene to Improve Sustainable Grapevine Production during Drought

OpenAIRE

Brillante, Luca; Belfiore, Nicola; Gaiotti, Federica; Lovat, Lorenzo; Sansone, Luigi; Poni, Stefano; Tomasi, Diego

2016-01-01

Viticulture is widely practiced in dry regions, where the grapevine is greatly exposed to water stress. Optimizing plant water use efficiency (WUE) without affecting crop yield, grape and wine quality is crucial to limiting use of water for irrigation and to significantly improving viticulture sustainability. This study examines the use in vineyards of particle film technology (engineered kaolin) and compares it to a film-forming antitranspirant (pinolene), traditionally used to limit leaf wa...

Influence of kaolin and firing temperature on the mullite formation in porous mullite-corundum materials

International Nuclear Information System (INIS)

Mahnicka, L; Svinka, R; Svinka, V

2011-01-01

The refractory ceramics became very important in both the traditional and the advanced materials applications as it has outstanding thermal and mechanical properties. The refractoriness of ceramics can be achieved by getting the mullite-corundum. Refractory ceramics with high porosity serve as a heat insulator and constructional material. Three series of porous mullite-corundum ceramic samples were prepared from Al 2 O 3 (Nabalox, Germany) and pure SiO 2 in 2.57:1 ratio that was conformed to mullite compositions (3Al 2 O 3 ·2SiO 2 ). α-Al 2 O 3 (d 50 = 4 μm) and γ-Al 2 O 3 (d 50 = 80 μm) were in 1:3 ratio. Quantity of kaolin (MEKA, Germany) was 10, 20 and 30 wt.%. Porous materials were prepared by slip casting of suspension of raw materials, where the aluminium paste (0.18 wt.%) was used as a pore former. Water content in the suspensions was 38-40 wt.%. Pore formation occured in result of hydrogen formation in chemical reaction between aluminium paste and water. The samples were sintered at 1650, 1700 and 1750°C temperature for one hour. SiO 2 and γ-Al 2 O 3 on the contrary reduced mechanical properties, but decreased shrinkage. Using of α-, γ-Al 2 O 3 , SiO 2 and kaolin in corresponding ratios the samples with open porosity of 30 to 54 vol% were acquired. The relative amounts of pores depended on the initial content of kaolin and on firing temperature.

Determination of the zero point of charge of kaolin waste from the Northeast of Para, BR

International Nuclear Information System (INIS)

Pinto, R.L.S.; Maia, R.F.S.; Felipe, A.M.P.F.

2012-01-01

The Para contributes with more than 50% of national production of kaolin of which 12.5% correspond to the waste generated, which has similar composition to benefited kaolin, can be used as adsorbent of heavy metals. The viscosity influences the design of equipment that can reuse that waste. The pH changes the pulp viscosity and the determination of the zero point of charge can estimate this variation. This study analyzes the influence of pH on the pulp rheology by the determination of the zero point of charge. Tests were made by Scanning Electron Microscopy, Energy Dispersive Spectroscopy, potentiometric titulation and rheological analysis. The results showed zero point of charge equal to 3.7 and confirmed that the viscosity increase at pH values near the zero point of charge and decrease at pH values away from this. (author)

Assessment of the adsorptive capacity of the Kaolin deposit targeting its use on the removal of colors in aqueous solution; Avaliacao da capacidade adsortiva do rejeito de caulim visando seu uso na remocao de corantes em solucao aquosa

Energy Technology Data Exchange (ETDEWEB)

Matos, S.C.; Hildebrando, E.A., E-mail: matos.cintia68@gmail.com [Universidade Federal do Para (FEMat/UFPA), PA (Brazil). Faculdade de Engenharia de Materiais

2016-07-01

The Amazonic region has large and valuable kaolin deposits. The state of Para by itself comprises three large industries which process kaolin. It has been noticed that the waste resulting from the processing of kaolin is rich in silico-aluminate, presenting potential in adsorption processes. Thus, this research's objective is to assess the kaolin waste produced during the processing phase, aiming at its application as low cost adsorbent material. For that, the kaolin waste has been characterized by X-ray diffraction and chemical analysis (XRF), and then sieved and calcined at 700 ° C, being then subjected to the adsorption process and observed qualitatively its capacity of retention by methylene blue (AM). Preliminary results show that the kaolin waste has satisfactory adsorption capacity at concentrations of up to 50.0 mg / MP, demonstrating the potential that it be used in the removal of dyes in wastewater treatment. (author)

Synthesis and characterization of ZSM-5 and calcined kaolin evaluation using the content of structure-directing

International Nuclear Information System (INIS)

Rodrigues, J.J.; Silva, V.J. da; Rodrigues, M.G.F.

2012-01-01

This study aims to evaluate the effect of the structure-directing content, tetrapropylammonium bromide, on the structural and morphological characteristics of ZSM-5 zeolite obtained using calcined kaolin as silicon and aluminum. The samples were characterized by XRD, EDX, SEM and Physics Adsorption N 2 . Trough X ray diffraction patterns was possible to observed the formation of the structure of ZSM-5 with intense peaks and well-defined characteristic of crystalline. The micrographs showed that the samples consist of agglomerates and/or aggregates of particles characteristic of the MFI structure typical of ZSM-5 zeolite. And through the adsorption-desorption isotherms physical N2 was possible to observe that the samples show hysteresis type I typical of microporous materials with specific surface areas of 218 and 222 m 2 /g. Therefore, the use of calcined kaolin to obtain ZSM-5 zeolite was effective. (author)

Study of the sodalite Bayer synthesis process from reject of kaolin of the Amazon region, Brazil

International Nuclear Information System (INIS)

Maia, A.A.B.; Neves, R.F.; Angelica, R.S.; Pöllmann, H.

2011-01-01

This work presents an application for the kaolin rejects from Amazonia through the synthesis of sodalite, in addition, the series of sodalites was synthesized with the same conditions of the Bayer process to understand and control their formation when necessary. These tailings are generated by companies located in the state of Para and are mainly composed of kaolinite, thus forming an excellent starting material for the production of zeolites. The synthesis process was carried out in autoclaves and two synthesis temperatures, 150 and 200 deg C, were evaluated, the same ones used in the Bayer process. The anions used in the reaction mixture to obtain the sodalite series were: carbonate chloride and sulfate, and NaOH solution was used as the sodium source. Sodalite was produced in all the synthesis conditions, showing that through the kaolin rejects from the Amazon it was possible to study the sodalite synthesis process.

Fly ash/Kaolin based geopolymer green concretes and their mechanical properties

Directory of Open Access Journals (Sweden)

F.N. Okoye

2015-12-01

Full Text Available Geopolymer concrete mixes were cast using fly ash, kaolin, sodium hydroxide, potassium hydroxide, sodium silicate and aggregates. Portland cement concrete (M30 was used as a reference sample. The effect of silica fume, temperature (40 °C, 60 °C, 80 °C, 100 °C and 120 °C, sodium and potassium hydroxides and different superplasticizers on the compressive strength are reported [1]. Maximum strength was found at 100 °C and 14 M alkali solution [1].

Electrokinetic remediation of heavy metals contaminated kaolin by a CNT-covered polyethylene terephthalate yarn cathode

International Nuclear Information System (INIS)

Yuan, Lizhu; Li, Haiyan; Xu, Xingjian; Zhang, Jing; Wang, Nana; Yu, Hongwen

2016-01-01

In the current study, carbon nanotube (CNT) covered polyethylene terephthalate yarns (PET-CNT) electrode has been investigated as a novel cathode material for the electrokinetic (EK) remediation of multi-metals (Cd, Cu, Ni, Pb, Zn) contaminated kaolin. The results of scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) showed that CNT was successfully covered on the surface of PET. The results obtained from EK process showed that PET-CNT as a cathode obviously elevated electric current and electro-osmotic flow (EOF), significantly decreased kaolin pH, and enhanced heavy metals removal efficiencies. The removal efficiencies of Cd, Cu, Ni, Pb, and Zn in PET-CNT treatment were 89.7%, 63.6%, 90.7%, 19.2%, and 88.7%, respectively. In comparison with the Pt/Ti and graphite treatments, the removal efficiencies of Cd, Ni, and Zn were improved at least about 30%, Cu and Pb were improved at least 16.6% and 6.9%, respectively. Our results demonstrated the PET-CNT was a good alternative cathode material for enhancing efficiency of EK remediation.

Mineralogical association in the zone of argillic advanced alteration in a kaolin deposit of Patagonia Argentina

International Nuclear Information System (INIS)

Rainoldi, A; Oviedo, P.; Maiza, P.; Marfil, S.

2010-01-01

This work is about the mineralogical and petrological relations of the para genetic association of advanced argillic zone in the kaolin deposit in Patagonia.This study allowed to establish the sequence of events that took place in the deposit as well as the conditions under which they were generated

Recovery of kaolinite from tailings of Zonouz kaolin-washing plant by flotation-flocculation method

Directory of Open Access Journals (Sweden)

Kianoush Barani

2018-04-01

Full Text Available The traditional processing of kaolin is achieved by dispersion of the mined ore and classification by multistage hydrocyclone plants. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back into the quarry. In this research, recovery of kaolinite from tailings of Zonouz kaolin washing plant, which is located in Iran was investigated by flotation and flotation- flocculation. Flotation experiments show that the flotation of kaolinite from the tailings is better in an acidic than in an alkaline medium containing cationic collectors. Flotation under acidic condition causes problems such as equipment corrosion at industrial scale. As a result, the cationic flotation of kaolinite is enhanced by addition of polyacrylamide as a flocculant. The results showed flocculation by polyacrylamide improved flotation of kaolinite within a range of pH. With 300 g/t dodecylamine, 500 g/t aluminum chloride, 50 g/t pine oil (frother, 15 g/t polyacrylamide, at pH = 7 and without de-slimming a product has 37.19% Al2O3, 54.19% SiO2 and 34.43% mass recovery was archived. Keywords: Kaolinite, Flotation, Flocculation, Cetylpyridinium chloride, Dodecylamine, Aluminum chloride, Polyacrylamide

Effect of Rice Husk and Diatomite on the Insulating Properties of Kaolin - Clay Firebricks

Directory of Open Access Journals (Sweden)

Emmanuel Ogo ONCHE

2007-09-01

Full Text Available This work was carried out to investigate the effect of rice husk and diatomite on the insulating properties of kaolin-clay firebrick. Five firebrick samples of different compositions were fired at 900°C, 1000°C, 1100°C, and 1200°C. Samples A-E are all insulating firebricks that can withstand temperatures ranging from 900°C to 1200°C since none of the samples crumbled during firing. The results showed that they all had good insulating characteristics with their highly porous structure making them suitable for backup insulation. Mixing ratios of 3:2:4:1 representing weight in grams of kaolin, plastic clay, rice husk and diatomite respectively for sample D gave the optimum performance values in terms of modulus of rupture, apparent porosity, apparent density, bulk density, and thermal conductivity at all temperatures. At 1200°C, the values are 22.57kgf/cm2 for modulus of rupture, 98.25% for apparent porosity, 2.38g/cm3 for apparent density, 1.11g/cm3 for bulk density, and 0.038w/mK for thermal conductivity.

Influence of the type of aqueous sodium silicate on the stabilization and rheology of kaolin clay suspensions

Science.gov (United States)

Izak, Piotr; Ogłaza, Longin; Mozgawa, Włodzimierz; Mastalska-Popławska, Joanna; Stempkowska, Agata

2018-05-01

To avoid agglomeration and sedimentation of grains, ceramic slurries should be modified by stabilizers in order to increase the electrostatic interactions between the dispersed particles. In this study we present the spectral analysis of aqueous sodium silicates obtained by different synthesis methods and their influence on the rheological properties of kaolin based slurries. Infrared and Raman spectra can be used to describe the structure of silicate structural units present in aqueous sodium silicates. It was confirmed that the best stabilization results possess aqueous sodium silicates of the silicate moduli of about 2 and the optimal concentration of the used fluidizer is 0.3 wt% to the kaolin clay dry mass. One of the most important conclusions is that the synthesis method of the fluidizer has no significant effect on its stabilization properties but used medium does create adequate stabilization mechanism depending on the silicate structures present in the sodium silicate solution.

国内外玻璃纤维用高岭土的质量差距及提高我国高岭土质量的对策%Differences of Kaolin Quality for Glass Fibers Made in China and Abroad and Improving Measures of Kaolin Quality Made in China

Institute of Scientific and Technical Information of China (English)

韩利雄; 姚远; 刘国斌

2011-01-01

Kaolins are one of important materials for E-glass fibers, which accounts for about 1/3 of blend mass. But the high-end market of kaolin for glass fibers was dominated by imports in China. Three kinds of kaolin samplespro-duced by ITC.Yichang and Yunnan for glass fibers were studied in this paper. The differences in chemical composition, phase,microstructure and granulometric composition were compared in detail by XRS,XRD,SEM and LPS. The research found that products of ITC had obvious advantages in product purity, particle size control and quality stability. In fact,the quality of domestic Kaolins is not bad,but because it is lack of specific quality standard and limited by the processing level of domestic non-metallic mineral, high-quality products cannot be obtained. In the future, kaolin industry should become bigger and stronger by integration as soon as possible, and try hard to improve the processing level of kaolin such as ore dressing,homogenization,etc,to fill the gap in the high-grade kaolin products for glass fibers.%高岭土是E-玻璃纤维的重要原料之一,其用量可占配合料的三分之一,但国内玻纤用高岭土高端市场一直被进口产品所占据.选取了美国ITC进口高岭土、宜昌硬质高岭土和云南水洗高岭土这三种有代表性的玻纤用高岭土,通过荧光光谱分析、X射线衍射分析、扫描电镜分析和激光粒度分析详细对比了它们在化学成分、物相组成、微观形貌和粒度分布四方面的差异.研究发现,美国玻纤用高岭土在产品纯度、粒度控制和质量稳定性方面有明显优势；国内玻纤用高岭土矿源品质并不差,只是由于缺乏专门的质量标准,同时受限于国内非金属矿产加工水平,而无法生产出高质量的产品.未来我国高岭土行业应尽快通过整合做大做强,努力提高高岭土选矿、均化等加工工艺水平,填补国内高档玻纤用高岭土产品空白.

Gravimetric and conductometric studies of the sedimentation kinetics in aqueous dispersions of kaoline

International Nuclear Information System (INIS)

Bulavyin, L.A.; Khrapatij, S.V.; Koval'chuk, V.Yi.; Klepko, V.V.; Lebovka, M.Yi.

2006-01-01

Using gravimetric and conductometric methods, the sedimentation kinetics in aqueous suspensions of Alekseev kaoline has been studied for pH value range from 4 to 10. It has been found that pH increasing leads to the decreasing of mean radii of flocks linearly. We found that sedimentation kinetics for intermediate pH values can be described by scaling equations that crossover time defined transition from a gravitational mechanism of deposition to the diffusion one

Sedimentation Characteristics of Kaolin and Bentonite in Concentrated Solutions

Directory of Open Access Journals (Sweden)

Abdulah Obut

2005-11-01

Full Text Available The sedimentation characteristics of two clays, namely kaolinite and bentonite, were determinated at high clay (5 % wt/vol and electrolyte (1 N concentrations using various inorganic-organic compounds. It was observed that the settling behaviour of kaolinite (1:1 clay and montmorillonite (2:1 clay is quite different due to the structural differences between these minerals. Although, similar initial settling rates and final sediment volumes were obtained after 24 hours of settling time for kaolin suspensions, the corresponding rates and volumes for bentonite suspensions varied greatly with the used chemical compound. According to the experimental results, a further intensive theoretical and experimental investigation is needed to reveal the mechanism underlying the sedimentation characteristics of clay minerals at high clay and electrolyte concentrations.

Behaviour of major, minor and trace elements (including REEs during kaolinization processes at Zonouz deposit, northeast of Marand, East Azarbaidjan province

Directory of Open Access Journals (Sweden)

Vahideh Alipour

2011-11-01

Full Text Available The Zonouz kaolin deposit is located ~15 km northeast of Marand, East-Azarbaidjan province. Based on physical features in field investigations, such as color, five distinct kaolin types including (1 white, (2 lemon, (3 gray, (4 brown, and (5 yellow are distinguished in the deposit. Field evidence and petrographic studies indicate that the deposit is genetically close to trachy-andesite rocks. According to mineralogical data, the deposit contains quartz, kaolinite, montmorillonite, calcite, pyrophyllite, chlorite, muscovite-illite, dolomite, hematite, and anatase minerals. Geochemical data indicate that function of alteration processes on trachy-andesite rocks during development of Zonouz ore deposit was accompanied by leaching of elements such as Al, Na, K, Rb, Ba, V, Hf, Cu, Zr, Tm, Yb, and Lu, enrichment of elements such as U, Nb, and Ta, and leaching-fixation of elements such as Si, Fe, Ca, Mg, Ti, Mn, P, Cs, Sr, Th, Co, Cr, Ni, Y, Ga, LREE, Tb, Dy, Ho, and Er. Incorporation of obtained results from mineralogical and geochemical studies show that physico-chemical conditions of alteration environment, the relative stability of primary minerals, surface adsorption, preferential sorption by metallic oxides, existing of organic matters, scavenging and concentration processes, and fixation in neomorphic mineralogical phases played important role in distribution of elements in the deposit. Geochemical studies show that development of the deposit is relative to two types of processes, (1 hypogene and (2 supergene. The distribution pattern of REEs indicates that differentiation degree of LREEs from HREEs in supergene kaolins is more than hypogene kaolins. Geochemical studies indicate that minerals such as Mn-oxides, zircon, anatase, hematite, cerianite, and secondary phosphates (monazite, rhabdophane, churchite, and zenotime are the potential hosts for rare earth elements in this deposit.

Zeolite A synthesized from wastes of kaolin improvement process; Zeolita A sintetizada a partir de rejeitos do processo de beneficiamento de caulim

Energy Technology Data Exchange (ETDEWEB)

Santana, D.L.; Neves, R.F.; Silva, D.L., E-mail: danielaliraeq@yahoo.com.br, E-mail: dasilva@ufpa.br [Programa de Pos-Graduacao em Engenharia Quimica, Universidade Federal do Para - UFPA, Belem, PA (Brazil); Saraiva, A.C.F. [Centro de Tecnologia da Eletronorte, Belem, PA (Brazil)

2012-04-15

Raw materials were used to synthesize zeolite A as an alternative and more economical source of silica and aluminum, using waste from the kaolin of the paper industry. Zeolites are crystalline substances with a structure characterized by a framework of linked tetrahedra, each one consisting of four oxygen atoms surrounding a cation. The development of processes for the synthesis of zeolites is of great interest for use in the areas of purification, adsorption and catalysis. The starting materials for the synthesis of zeolite A consisted of wastes from kaolin beneficiation of paper companies of Para state, Brazil. The zeolite was obtained after calcination at 85 and 110 deg C during 24 h. The characterization of the starting material was performed by X-ray diffraction, chemical analysis, thermogravimetric and differential thermal analysis, and scanning electron microscopy. The characterization of zeolite A was done by X-ray diffraction and scanning electron microscopy. The kaolin waste used as starting material showed to be essentially kaolinite mineral. For the temperatures and time used in the synthesis it was possible to form the crystalline phase of zeolite A for the two starting materials. (author)

Gamma-induced radiation polymerization of kaolin composite for sorption of lanthanum, europium and uranium ions from low-grade monazite leachate

International Nuclear Information System (INIS)

Metwally, S.S.; Hassan, R.S.; El-Masry, E.H.; Borai, E.H.

2018-01-01

Gamma radiation polymerization method was used for the modification of kaolin to produce (poly acrylamide-acrylic acid)-Kaolin (PAM-AA-K). Monazite ore is one of the main resources of uranium and lanthanide elements, therefore, this work focused on sorption of uranium, lanthanum and europium ions from low grade monazite leachate. The removal percent for Eu 3+ , La 3+ and UO 2 2+ are 94.6, 91.6 and 73.4%, respectively. Monolayer capacity of Eu 3+ , La 3+ and UO 2 2+ were found to be 54.64, 45.87 and 37.59 mg/g, respectively. The sorption mechanism of lanthanum and europium ions on PAM-AA-K composite mainly takes place as Ln(OH) 2+ , and for uranium as uranyl ion, UO 2 2+ . (author)

Effect of Kaolin Clay and Alumina on Thermal Performance and Char Morphology of Intumescent fire retardant coating

Directory of Open Access Journals (Sweden)

aziz Hammad

2014-07-01

Full Text Available Intumescent fire retardant coating (IFRC have been developed by using ammonium polyphosphate, expandable graphite, melamine, boric acid, kaolin clay and alumina as fillers bound together with epoxy resin and cured with the help of curing agent. Five different formulations were developed with and without using fillers. Cured samples were burned in furnace at 500°C for 2h for char expansion. Bunsen burner test was performed for 1h using UL-94 vertical burning test to investigate the thermal performance of IFRC. The resultant char obtained after burning of coated samples were characterized by using field emission scanning electron microscopy for char morphology. Char composition was analyzed by using fourier transform infrared spectroscopy. Thermogravimetric analysis was carried out to investigate the residual weight of coating. Results showed that formulation with 0.5 weight % of kaolin clay and 0.5 weight % of alumina provide best thermal performance, uniform and multi-porous char structure with high anti-oxidation property.

Particle morphology and mineral structure of heavy metal-contaminated kaolin soil before and after electrokinetic remediation.

Science.gov (United States)

Roach, Nicole; Reddy, Krishna R; Al-Hamdan, Ashraf Z

2009-06-15

This study aims to characterize the physical distribution of heavy metals in kaolin soil and the chemical and structural changes in kaolinite minerals that result from electrokinetic remediation. Three bench-scale electrokinetic experiments were conducted on kaolin that was spiked with Cr(VI) alone, Ni (II) alone, and a combination of Cr(VI), Ni(II) and Cd(II) under a constant electric potential of 1VDC/cm for a total duration of 4 days. Transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD) analyses were performed on the soil samples before and after electrokinetic remediation. Results showed that the heavy metal contaminant distribution in the soil samples was not observable using TEM and EDX. EDX detected nickel and chromium on some kaolinite particles and titanium-rich, high-contrast particles, but no separate phases containing the metal contaminants were detected. Small amounts of heavy metal contaminants that were detected by EDX in the absence of a visible phase suggest that ions are adsorbed to kaolinite particle surfaces as a thin coating. There was also no clear correlation between semiquantitative analysis of EDX spectra and measured total metal concentrations, which may be attributed to low heavy metal concentrations and small size of samples used. X-ray diffraction analyses were aimed to detect any structural changes in kaolinite minerals resulting from EK. The diffraction patterns showed a decrease in peak height with decreasing soil pH value, which indicates possible dissolution of kaolinite minerals during electrokinetic remediation. Overall this study showed that the changes in particle morphology were found to be insignificant, but a relationship was found between the crystallinity of kaolin and the pH changes induced by the applied electric potential.

Particle morphology and mineral structure of heavy metal-contaminated kaolin soil before and after electrokinetic remediation

International Nuclear Information System (INIS)

Roach, Nicole; Reddy, Krishna R.; Al-Hamdan, Ashraf Z.

2009-01-01

This study aims to characterize the physical distribution of heavy metals in kaolin soil and the chemical and structural changes in kaolinite minerals that result from electrokinetic remediation. Three bench-scale electrokinetic experiments were conducted on kaolin that was spiked with Cr(VI) alone, Ni (II) alone, and a combination of Cr(VI), Ni(II) and Cd(II) under a constant electric potential of 1 VDC/cm for a total duration of 4 days. Transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD) analyses were performed on the soil samples before and after electrokinetic remediation. Results showed that the heavy metal contaminant distribution in the soil samples was not observable using TEM and EDX. EDX detected nickel and chromium on some kaolinite particles and titanium-rich, high-contrast particles, but no separate phases containing the metal contaminants were detected. Small amounts of heavy metal contaminants that were detected by EDX in the absence of a visible phase suggest that ions are adsorbed to kaolinite particle surfaces as a thin coating. There was also no clear correlation between semiquantitative analysis of EDX spectra and measured total metal concentrations, which may be attributed to low heavy metal concentrations and small size of samples used. X-ray diffraction analyses were aimed to detect any structural changes in kaolinite minerals resulting from EK. The diffraction patterns showed a decrease in peak height with decreasing soil pH value, which indicates possible dissolution of kaolinite minerals during electrokinetic remediation. Overall this study showed that the changes in particle morphology were found to be insignificant, but a relationship was found between the crystallinity of kaolin and the pH changes induced by the applied electric potential.

Radiological impacts of the usability of Dolerite and Kaolin as raw materials for construction works in Abia State, Nigeria

International Nuclear Information System (INIS)

Enyinna, P.I.; Avwiri, G. O.

2011-01-01

This research study is aimed at carrying out radiometric analyses of the natural radioactivity resulting from the presence of radionuclides in dolerite and kaolin which are raw materials widely used in construction works. The activity concentrations of the identified natural radionuclides of 226 Ra, 228 Ra and 40 K in 40 samples of these solid minerals collected from 4 mining sites were determined by gamma ray spectroscopic technique using a well calibrated [NaI(Tl)] detector. The mean values of the activity concentrations of 226 Ra, 228 Ra and 40 K for the dolerite samples were found to be 10.989Bq/kg, 6.956Bq/kg, 723.253Bq/kg and 10.735Bq/kg, 6.175Bq/kg, 714.895Bq/kg respectively (for the 2 dolerite mining sites); and for the kaolin samples, 8.507Bq/kg, 7.33Bq/kg, 87.511Bq/kg and 8.416Bq/kg, 7.354Bq/kg, 86.727Bq/kg respectively (for the 2 kaolin mining sites). The radium equivalent activity, the absorbed dose rate, the equivalent dose rate, the external and internal hazard indices, the annual outdoor and indoor effective dose rates were computed and compared with international radiological standards to ascertain if these minerals pose any radiological hazard. The results obtained were found to conform within the limits of acceptable international radiological standards and may not pose any immediate threat to the public and users of these two solid minerals for construction works.

Utilisation of Sand from Kaolin Washing for the Manufacture of Alkali-activated Artificial Sandstone

Science.gov (United States)

Vavro, Martin; Vavro, Leona; Mec, Pavel; Soucek, Kamil; Pticen, Frantisek; Reiterman, Pavel

2017-04-01

Sandstones represent a traditional natural stones which are widely used in Czech architecture and sculpture over a long time. Thanks to their relatively easy workability, sandstones provide a wide range of stone products and also represent a popular material for architectural and sculptural purposes. In the field of restoration of artworks, they are therefore often used for manufacturing stone statue copies originally made from the same or similar type of stone. Despite a relatively common and varied occurrence of natural sandstones, the method of the artificial stone facsimiles creation in the form of various cast elements is also often applied in restoration practice. The history of application of artificial stones in civil engineering and architecture goes back to the ancient times, i.e. to Roman antiquity and possibly up to the time of ancient Egypt. The lack of appropriate natural rock, suitable in the view of colour, grain size or texture is the main reason of manufacturing copies based on synthetic mixtures. The other reason is high financial costs to create a sculpture copy from natural materials. Mixtures made from white and/or grey cements, sands, carefully selected crushed stone or well graded natural gravels, and mineral coloring pigments or mixtures with acrylate, polyester, and epoxy resins binder are the most frequently used artificial materials for cast stone manufacturing. This paper aims to bring information about composition and properties of artificial sandstones made from alkali-activated binder mixtures based on metakaolin and granulated blast furnace slag. The filler of this artificial stone is represented by fine-grained sand generated during kaolin wet processing. Used sand is mainly formed by quartz, feldspars, micas (muscovite > biotite), residual kaolin, and to a lesser extent also by Fe oxyhydroxides ("limonite"), titanium dioxide mineral (probably anatase), and carbonate mineral unidentified in detail. Annual Czech production of this

Synthesis of 4A zeolites from kaolin for obtaining 5A zeolites through ionic exchange for adsorption of arsenic

International Nuclear Information System (INIS)

Resmini Melo, Carolina; Gracher Riella, Humberto; Cabral Kuhnen, Nivaldo; Angioletto, Elidio; Melo, Aline Resmini; Bernardin, Adriano Michael; Rocha, Marcio Roberto da; Silva, Luciano da

2012-01-01

Highlights: ► We synthesize 4A zeolite from kaolin by hydrothermal reaction with sodium hydroxide. ► The 4A zeolite synthesized underwent ion exchange with calcium ions, with different parameters, to obtain 5A zeolites. ► The best 4A zeolite obtained was used as adsorbent material for arsenic ions. ► The results showed that the 5A zeolite material obtained is a good adsorber of heavy ions. - Abstract: The synthesis of adsorbing zeolite materials requires fine control of the processing variables. There are distinct process variable settings for obtaining specific desired types of zeolites. The intent of this study was to obtain 4A zeolites from kaolin in order to obtain 5A zeolites through ionic exchange with the previously synthesized zeolite. This zeolite 5A was used as an adsorbent for arsenic ions. The results obtained were satisfactory.

Contrasting respirable quartz and kaolin retention of lecithin surfactant and expression of membranolytic activity following phospholipase A2 digestion.

Science.gov (United States)

Wallace, W E; Keane, M J; Mike, P S; Hill, C A; Vallyathan, V; Regad, E D

1992-11-01

Respirable-sized quartz, a well-established fibrogenic mineral dust, is compared with kaolin in erythrocyte hemolysis assays after treatment with saline dispersion of dipalmitoyl phosphatidylcholine, a primary phospholipid component of pulmonary surfactant. Both dusts are rendered inactive after treatment, but the membranolytic activity is partly to fully restored after treatment with phospholipase A2, an enzyme normally associated with cellular plasma membranes and lysosomes. Phospholipid-coated dusts were incubated for periods of 2-72 h at a series of applied enzyme concentrations, and the adsorbed lipid species and hemolytic activity were quantitated at each time for both dusts. Surfactant was lost more readily from quartz than from kaolin, with consequent more rapid restoration of mineral surface hemolytic activity for quartz. Interactions of surfactant and mineral surface functional groups responsible for the mineral-specific rate differences, and implications for determining the mineral surface bioavailability of silica and silicate dusts, are discussed.

Incorporation of feasibility study of residue thin kaolin in of porcelain formulations production; Estudo da viabilidade da incorporacao do residuo fino do caulim na concepcao de formulacoes de porcelanatos

Energy Technology Data Exchange (ETDEWEB)

Almeida, V.S. de; Ferreira, E.C.; Oliveira, T.M. de; Freitas, K.D. de Araujo; Soares Filho, J.E.; Sousa, F.J.P. de, E-mail: vanessaalmeida90@gmail.com [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2016-07-01

The porcelain is the more advanced product among traditional ceramics due to the high technology used in its manufacture and its excellent technological and aesthetic properties. Due to the continuing worldwide development, kaolin processing industries have increased their productivity and consequently generating large amounts of waste, contributing to environmental degradation. Studies are being conducted to analyze the incorporation of such wastes in the ceramic mass compositions. The objective of this study was to evaluate 4 formulations of porcelain as the possibility of using waste coming from the last stage of kaolin processing. Processing occurred by wet grinding process, with uniaxial compacting pressure of 45 MPa after heat treatment at 1250 ° C. Technological tests were carried out physical and mechanical product. The results showed that the addition of fine kaolin residue was presented as an efficient alternative for the porcelain industry. (author)

Immobilization of horseradish peroxidase onto kaolin by glutaraldehyde method and its application in decolorization of anthraquinone dye

Directory of Open Access Journals (Sweden)

Šekuljica Nataša Ž.

2016-01-01

Full Text Available The problem of environmental pollution day by day becomes more worrisome, primarily due to the large amounts of wastewater contaminated with various harmful organic compounds, discharged into the environment untreated or partially clean. Feasibility of use of horseradish peroxidase (Amoracia rusticana in the synthetic dyes decolorization was approved by many researchers. Among a number of supports used for the immobilization, it was found that natural clay, kaolin has excellent features which are a precondition for obtaining biocatalysts with the excellent performances. For this reason, a horseradish peroxidase was immobilized onto kaolin using glutaraldehyde as a cross-linking agent. Obtained biocatalyst was applied in the decolorization of anthraquinone dye C. I. Acid Violet 109. Under determined optimal conditions (pH 4.0, hydrogen peroxide concentration 0.6 mM, dye concentration 30 mg L-1, temperature 24ºC around 76 % of dye decolorization was achieved. Reusability study showed that resulting biocatalyst was possible to apply four times in the desired reaction with relatively high decolorization percentage. [Projekat Ministarstva nauke Republike Srbije, br. III-46010 i br. 172013

Application of kaolin-based catalysts in biodiesel production via transesterification of vegetable oils in excess methanol.

Science.gov (United States)

Dang, Tan Hiep; Chen, Bing-Hung; Lee, Duu-Jong

2013-10-01

Biodiesel production from transesterification of vegetable oils in excess methanol was performed by using as-prepared catalyst from low-cost kaolin clay. This effective heterogeneous catalyst was successfully prepared from natural kaolin firstly by dehydroxylation at 800°C for 10h and, subsequently, by NaOH-activation hydrothermally at 90°C for 24h and calcined again at 500°C for 6h. The as-obtained catalytic material was characterized with instruments, including FT-IR, XRD, SEM, and porosimeter (BET/BJH analysis). The as-prepared catalyst was advantageous not only for its easy preparation, but also for its cost-efficiency and superior catalysis in transesterification of vegetable oils in excess methanol to produce fatty acid methyl esters (FAMEs). Conversion efficiencies of soybean and palm oils to biodiesel over the as-prepared catalysts reached 97.0±3.0% and 95.4±3.7%, respectively, under optimal conditions. Activation energies of transesterification reactions of soybean and palm oils in excess methanol using these catalysts are 14.09 kJ/mol and 48.87 kJ/mol, respectively. Copyright © 2012 Elsevier Ltd. All rights reserved.

Potential of kaolin-based particle film barriers for Formosan subterranean termite (Isoptera: Rhinotermitidae) control

Science.gov (United States)

Wiltz, B.A.; Woodson, W.D.; Puterka, G.J.

2010-01-01

Effects of three particle film products on Formosan subterranean termites, Coptotermes formosanus Shiraki, were evaluated in feeding, tunneling, and contact assays. The particle films, hydrophobic M96-018 and hydrophilic Surround and Surround WP are based on the inert clay mineral kaolin. In 2-week long no-choice feeding tests, significant mortality occurred only with M96-018-coated wood. When a choice was provided, M96-018 and Surround were consumed at higher rates than untreated wood. Surround WP did not differ from controls in either test. In the tunneling assay termites were given the option of crossing a kaolin-sand mixture to reach an alternate food source. After 3-weeks, rates of 1% and 5% M96-018 provided an effective barrier to Formosan termite tunneling, while termites were not stopped by rates as high as 20% Surround and Surround WP. Dust treatments of all three formulations caused significant increases in mortality within 24 h, with mortality rates ranging from 72.0 - 97.3% within 72 h of treatment. The particle films were most effective when moisture levels were low, suggesting that desiccation was the mechanism for mortality. All particle films showed potential for use in above ground applications while hydrophobic M06-018 has the most potential as a soil barrier to subterranean termites.

Waste characterization emanated from kaolin submitted the improvement to process hydrocycloning

International Nuclear Information System (INIS)

Barbosa Neto, M.C.; Nunes, A.S.; Caetano, A.L.A.; Marques, V.C.; Macedo, D.A.; Ferreira, H.S.; Dutra, R.P.S.

2016-01-01

The hydrocyclones are equipment commonly used for separation of particles by size. The resulting material of this process usually presents different characteristics of the material, which was not subjected to treatment. Therefore, a study of the waste characteristics derived from kaolin processing submitted to hydrocycloning process compared to the same residue without going through the process was executed. The different samples were characterized by X-ray diffraction, X-ray fluorescence, particle size analysis and thermal analysis. The results indicate that the hydrocycloning not modify the mineralogical structure nor chemical material. The particle size analysis identified that the fine fraction, resulting from the process, presented particle size lower than the reference material. (author)

Characterization of ceramic masses using raw material of Para, Brazil: kaolin in natura; Caracterizaco de massas ceramicas utilizando materia--prima do Para: caulim in natura

Energy Technology Data Exchange (ETDEWEB)

Vida, T.A.; Facury Neto, E.; Rabelo, A.A. [Universidade Federal do Para (UFPA), Maraba, PA (Brazil). Fac. de Engenharia de Materiais

2009-07-01

The incorporation rejects to the mixtures has if shown viable in the reduction of the environmental liability and for the obtaining of a better quality of the ceramic mass. In the present work, is tried to study the potentiality of the use of ceramic formulations with the addition of kaolin in natura to the clays. Formulations with two clays of the area of the municipal district of Maraba with addition of up to 60% in kaolin weight were prepared and characterized. For the determination of the physical and mechanical properties proof bodies were made by prensagem uniaxial and later burned in temperature from 900 to 1200 deg C with landing of 3 hours. The raw materials were characterized through diffraction of rays X (DRX) and thermogravimetric analysis. The proof bodies prepared were used for determination of the lineal retraction (RL), absorption of water, apparent porosity, apparent density, loss to the fire and rupture module the flexing. The results were satisfactory for the smallest kaolin tenors in the ceramic mass, and the mass with 20% presented rupture module elevated, in the temperature of 1200 deg C. (author)

Facile Fabrication of a PDMS@Stearic Acid-Kaolin Coating on Lignocellulose Composites with Superhydrophobicity and Flame Retardancy

Directory of Open Access Journals (Sweden)

Zhe Wang

2018-05-01

Full Text Available The disadvantages such as swelling after absorbing water and flammability restrict the widespread applications of lignocellulose composites (LC. Herein, a facile and effective method to fabricate superhydrophobic surfaces with flame retardancy on LC has been investigated by coating polydimethylsiloxane (PDMS and stearic acid (STA modified kaolin (KL particles. The as-prepared coatings on the LC exhibited a good repellency to water (a contact angle = 156°. Owing to the excellent flame retardancy of kaolin particles, the LC coated with PDMS@STA-KL displayed a good flame retardancy during limiting oxygen index and cone calorimeter tests. After the coating treatment, the limiting oxygen index value of the LC increased to 41.0. Cone calorimetry results indicated that the ignition time of the LC coated with PDMS@STA-KL increased by 40 s compared with that of uncoated LC. Moreover, the peak heat release rate (PHRR and the total heat release (THR of LC coated with PDMS@STA-KL reduced by 18.7% and 19.2% compared with those of uncoated LC, respectively. This LC coating with improved water repellency and flame retardancy can be considered as a potential alternative to protect the lignocellulose composite.

Attenuation measurements of ultrasound in a kaolin-water slurry. A linear dependence upon frequency

International Nuclear Information System (INIS)

Greenwood, M.S.; Mai, J.L.; Good, M.S.

1993-01-01

The attenuation of ultrasound through a kaolin-water slurry was measured for frequencies ranging from 0.5 to 3.0 MHz. The maximum concentration of the slurry was for a weight percentage of 44% (or a volume fraction of 0.24). The goal of these measurements was to assess the feasibility of using ultrasonic attenuation to determine the concentration of a slurry of known composition. The measurements were obtained by consecutively adding kaolin to the slurry and measuring the attenuation at each concentration. After reaching a maximum concentration a dilution technique was used, in which an amount of slurry was removed and water was added, to obtain the attenuation as a function of the concentration. The dilution technique was the more effective method to obtain calibration data. These measurements were carried out using two transducers, having a center frequency of 2.25 MHz, separated by 0.1016m (4.0 in.). The maximum attenuation measured in these experiments was about 100Np/m, but the experimental apparatus has the capability of measuring a larger attenuation if the distance between the two transducers is decreased. For a given frequency, the data show that ln V/V 0 depends linearly upon the volume fraction (V is the received voltage for the slurry and V 0 is that obtained for water). This indicated that each particle acts independently in attenuating ultrasound. 12 refs., 7 figs., 3 tabs

High-temperature CO2 capture cycles of hydrated limestone prepared with aluminum (hydr)oxides derived from kaolin

International Nuclear Information System (INIS)

Wang, Ke; Zhao, Pengfei; Guo, Xin; Han, Dongtai; Chao, Yang

2014-01-01

Highlights: • Hydrated limestone exhibited a higher reactivity and stability. • Microstructure of hydrated limestone was significantly improved. • Hydrated limestone still suffered less loss-incapacity. • Hydrated limestone sorbents with kaolin-based binders were prepared and characterized. • Sorbents prepared from hydrated limestone and Al(OH) 3 binder are a promising sorbent. - Abstract: A simple and convenient process was used to improve the utilization of natural limestone and kaolin for calcium looping technology and environmental applications. The calcined natural limestone modified with the distilled water (denoted as Limestone-W), was systematically studied and compared with the other CaO sorbents (calcium acetate, calcium D-gluconate and calcined natural limestone). These CaO-based sorbents were tested for their CO 2 capture behavior through 20 carbonation/calcination cycles in a thermo-gravimetric analyzer (TGA). Their morphology, pore structure and phase composition before and after carbonation/calcination cycles were determined by scanning electron microscopy, nitrogen adsorption, and X-ray diffraction. The first-cycle and multicycle sorption results revealed that the Limestone-W sorbent exhibited a relatively faster reaction rate and higher cyclic CO 2 capture. The characterization data indicated that the Limestone-W was composed of a special calcium oxide structure with lower crystalline and higher porosity nanoparticles, which appeared to be the main reasons for its higher CO 2 capture capability. However, the Limestone-W still suffered loss of reactivity, even though it was less pronounced than the other CaO sorbent. To avoid this unfavorable effect, a thermally stable inert material (aluminum hydroxide derived from kaolin) was incorporated into the Limestone-W structure. This new sorbent revealed higher stability because the formation of a stable framework of Ca 12 Al 14 O 33 particles hindered densification and sintering of the CaO phase

Mineralogical characterization and beneficiation study of kaolin from Equador (RN) and Junco do Serido (PB) to increase the brightness index

International Nuclear Information System (INIS)

Campos, V.M.J.S.; Bertolino, L.C.; Alves, O.C.

2017-01-01

Kaolin is a rock composed mainly of kaolinite. It is used in many industrial segments, such as paper and ceramics. However, for these uses it is necessary to submit the ore to appropriate beneficiation, which generally involves magnetic separation and chemical bleaching, aiming to remove iron oxide and hydroxide, raising brightness index. This work reports the mineralogical characterization and analysis of the beneficiation of three samples of kaolin, two from Equador (Rio Grande do Norte - RN) and the third from Junco do Serido (Paraiba - PB). The samples were submitted to granulometric classification in sieve of 44 μm, magnetic separation in a magnetic induction of 14000 gauss, and chemical bleaching with sodium dithionite during 240 min. The processes were divided into two beneficiation routes. X-ray diffraction, chemical analysis by X-ray fluorescence and scanning electron microscopy were used for mineralogical characterization of the ore and measurement of the brightness index, while electron paramagnetic resonance was applied to study the variation of iron oxides and hydroxides during beneficiation. The results indicate that just 30 min of chemical bleaching without magnetic separation was sufficient to increase the brightness index from 78.2 to 90.2% and from 91.3 to 95.7% in the two samples from Equador (RN) and from 86.9 to 90.4% in the sample from Junco do Serido (PB). The magnetic separation, although causing a small increase in the brightness index, was inefficient for removal of iron oxides and hydroxides. The results indicated no need for using magnetic separation in plants for beneficiation of kaolin from these two locations, providing the reduction of production costs allowing better exploitation of the ore. (author)

For production of ceramic plates coating using waste kaolin, granite and marble

International Nuclear Information System (INIS)

Sales, J.L.; Morais, C.R.S.; Lima, L.M.R.; Altidis, M.E.D.

2011-01-01

The objective is to benefit and characterize waste from kaolin, marble and granite studying their thermal properties and spectroscopic in employment perspective on ceramic production of flooring boards. The residues were benefited through the process of dry grinding mill in greyhounds and passed through sieve 0.074 mm (ABNT No. 200), observing their suitability for the formulation of ceramic pastes. Tests were performed physicochemical characterization (particle size analysis, X-ray fluorescence and X-ray diffraction) and thermal (differential thermal analysis and thermogravimetry). The results showed that these residues showed satisfactory properties for the purpose for which it proposes, and contribute to reducing environmental impacts, allowing the reuse of the production of ceramic plates (author)

Mineralogical and chemical characterization of DD3 kaolin from the east of Algeria

Energy Technology Data Exchange (ETDEWEB)

Senoussi, H.; Osmani, H.; Courtois, C.; Bourahli, M. H.

2016-08-01

The mineralogical and chemical characteristics, based on X-ray diffraction (XRD) and scanning electron microscopy, of a kaolin known as DD3, from eastern Algeria were examined in the present study. The results showed that kaolin DD3 has an alumina content of 39%. The SiO{sub 2}/Al{sub 2}O{sub 3} molar ratio of 2.14 is close to that of a pure halloysite. The hematite concentration is relatively large and the flux oxides ratios remain as acceptable impurities. Microscopic observations showed a predominant tubular halloysite phase, flattened hexagonal platelets corresponding to the presence of kaolinite and its polymorphs (nacrite, dickite), and hydrated alumina. The SiO{sub 2}/Al{sub 2}O{sub 3} molar ratio and tubular DD3 suggest possible uses in technical ceramics and nano technology applications. Analysis by XRD revealed the presence of many phases. Thermal treatment at 450 degree centigrade and chemical treatment with HCl confirmed the presence of halloysite. The inclusion in the clay of organic molecules (dimethylsulfoxide (DMSO), DMF, and diluted glycerol) showed that the DMSO led to expansion of the inter-planar distance. The intercalation by DMSO molecules resulted in a shift of the basal peak from 10 to 11.02 A and partial displacement of the peak from 3.35 to 3.65 A. These two peaks are characteristic of halloysite. The presence of residual nacrite was also confirmed by the shift of the peak observed at 3.35 A. A full analysis of the XRD patterns using the Match software, based on these results, showed that the DD3 clay consists of >60% halloysite. (Author)

Mineralogical and chemical characterization of DD3 kaolin from the east of Algeria

International Nuclear Information System (INIS)

Senoussi, H.; Osmani, H.; Courtois, C.; Bourahli, M. H.

2016-01-01

The mineralogical and chemical characteristics, based on X-ray diffraction (XRD) and scanning electron microscopy, of a kaolin known as DD3, from eastern Algeria were examined in the present study. The results showed that kaolin DD3 has an alumina content of 39%. The SiO 2 /Al 2 O 3 molar ratio of 2.14 is close to that of a pure halloysite. The hematite concentration is relatively large and the flux oxides ratios remain as acceptable impurities. Microscopic observations showed a predominant tubular halloysite phase, flattened hexagonal platelets corresponding to the presence of kaolinite and its polymorphs (nacrite, dickite), and hydrated alumina. The SiO 2 /Al 2 O 3 molar ratio and tubular DD3 suggest possible uses in technical ceramics and nano technology applications. Analysis by XRD revealed the presence of many phases. Thermal treatment at 450 degree centigrade and chemical treatment with HCl confirmed the presence of halloysite. The inclusion in the clay of organic molecules (dimethylsulfoxide (DMSO), DMF, and diluted glycerol) showed that the DMSO led to expansion of the inter-planar distance. The intercalation by DMSO molecules resulted in a shift of the basal peak from 10 to 11.02 A and partial displacement of the peak from 3.35 to 3.65 A. These two peaks are characteristic of halloysite. The presence of residual nacrite was also confirmed by the shift of the peak observed at 3.35 A. A full analysis of the XRD patterns using the Match software, based on these results, showed that the DD3 clay consists of >60% halloysite. (Author)

Simultaneous removal of organic contaminants and heavy metals from kaolin using an upward electrokinetic soil remediation process

International Nuclear Information System (INIS)

Wang, J.-Y.; Huang, X.-J.; Kao, Jimmy C.M.; Stabnikova, Olena

2007-01-01

Kaolins contaminated with heavy metals, Cu and Pb, and organic compounds, p-xylene and phenanthrene, were treated with an upward electrokinetic soil remediation (UESR) process. The effects of current density, cathode chamber flushing fluid, treatment duration, reactor size, and the type of contaminants under the vertical non-uniform electric field of UESR on the simultaneous removal of the heavy metals and organic contaminants were studied. The removal efficiencies of p-xylene and phenanthrene were higher in the experiments with cells of smaller diameter or larger height, and with distilled water flow in the cathode chamber. The removal efficiency of Cu and Pb were higher in the experiments with smaller diameter or shorter height cells and 0.01 M HNO 3 solution as cathode chamber flow. In spite of different conditions for removal of heavy metals and organics, it is possible to use the upward electrokinetic soil remediation process for their simultaneous removal. Thus, in the experiments with duration of 6 days removal efficiencies of phenanthrene, p-xylene, Cu and Pb were 67%, 93%, 62% and 35%, respectively. The experiment demonstrated the feasibility of simultaneous removal of organic contaminants and heavy metals from kaolin using the upward electrokinetic soil remediation process

Short communication: Laboratory approach to the use of sulphur and kaolin as preventive control against Drosophila suzukii

Energy Technology Data Exchange (ETDEWEB)

Pérez-Guerrero, S.; Molina, J.M.

2016-11-01

Drosophila suzukii (Matsumura, 1931) is an invasive pest from South East Asia that was detected for the first time in Southern Europe in 2008. This species can damage a wide range of soft-skinned fruits crops affecting ripening fruits and causing important economic losses. Since the exclusive use of chemical insecticides for controlling D. suzukii may prompt the appearance of resistance and environmental pollution, alternative methods compatible with sustainable management are required. In this study, commercial formulations of powdered sulphur and kaolin were tested as a preventive method applied to blueberry fruits under laboratory conditions. In no-choice assay, powdered sulphur had a significant effect on oviposition and adult emergency with reductions of 76% and 77%, respectively. In addition, sulphur displayed a significant toxicity on males and lethal effect with over 40% adult mortality seven days after exposure. The choice assay confirmed and improved the powdered sulphur effects, with reductions of 98% and 96% in oviposition and adult emergence, respectively. In contrast, kaolin produced no significant reduction in infestation and adult mortality during no-choice and choice assays. These outcomes suggest that preventive use of powdered sulphur could be considered for sustainable control of D. suzukii in some berry crops. (Author)

Short communication: Laboratory approach to the use of sulphur and kaolin as preventive control against Drosophila suzukii

Directory of Open Access Journals (Sweden)

Sergio Pérez-Guerrero

2016-06-01

Full Text Available Drosophila suzukii (Matsumura, 1931 is an invasive pest from South East Asia that was detected for the first time in Southern Europe in 2008. This species can damage a wide range of soft-skinned fruits crops affecting ripening fruits and causing important economic losses. Since the exclusive use of chemical insecticides for controlling D. suzukii may prompt the appearance of resistance and environmental pollution, alternative methods compatible with sustainable management are required. In this study, commercial formulations of powdered sulphur and kaolin were tested as a preventive method applied to blueberry fruits under laboratory conditions. In no-choice assay, powdered sulphur had a significant effect on oviposition and adult emergency with reductions of 76% and 77%, respectively. In addition, sulphur displayed a significant toxicity on males and lethal effect with over 40% adult mortality seven days after exposure. The choice assay confirmed and improved the powdered sulphur effects, with reductions of 98% and 96% in oviposition and adult emergence, respectively. In contrast, kaolin produced no significant reduction in infestation and adult mortality during no-choice and choice assays. These outcomes suggest that preventive use of powdered sulphur could be considered for sustainable control of D. suzukii in some berry crops.

Comparative numerical study of kaolin clay with three drying methods: Convective, convective–microwave and convective infrared modes

International Nuclear Information System (INIS)

Hammouda, I.; Mihoubi, D.

2014-01-01

Highlights: • Modelling of drying of deformable media. • Theoretical study of kaolin clay with three drying methods: convective, convective–microwave and convective infrared mode. • The stresses generated during convective, microwave/convective drying and infrared/convective drying. • The combined drying decrease the intensity of stresses developed during drying. - Abstract: A mathematical model is developed to simulate the response of a kaolin clay sample when subjected to convective, convective–microwave and convective–infrared mode. This model is proposed to describe heat, mass, and momentum transfers applied to a viscoelastic medium described by a Maxwell model with two branches. The combined drying methods were investigated to examine whether these types of drying may minimize cracking that can be generated in the product and to know whether the best enhancement is developed by the use of infra-red or microwave radiation. The numerical code allowed us to determine, and thus, compare the effect of the drying mode on drying rate, temperature, moisture content and mechanical stress evolutions during drying. The numerical results show that the combined drying decrease the intensity of stresses developed during drying and that convective–microwave drying is the best method that gives a good quality of dried product

Synthesis and characterization of kaolin assisted metal nanocomposite and its tremendous adsorptive and photo catalytic applications

International Nuclear Information System (INIS)

Tahir, H.; Saad, M.; Saleem, U.

2018-01-01

The present work demonstrates the synthesis of Kaolin assisted Ag nanocomposite (Ag-KNC) by co-precipitation method. The surface morphology of them was studied through SEM and chemical constituents by EDS techniques. The removal of efficaciousness of Ag-KNC was tested by Malachite Green Oxalate (MGO) dye through batch adsorption and photocatalytic strategies. The sorption experiments were preceded under the optimized conditions like amount of adsorbent, stay time and pH. The feasibility of the process was determined by employing Freundlich, Langmuir and D-R (Dubinin –Radushkevich) adsorption isotherms. The pH at point of zero charge (pHpzc) was conjointly calculable to work out the surface neutrality of the system. The salt effect for the removal of MGO dye was investigated. Thermodynamic parameters like free energy (∆Go), entropy (∆So) and enthalpy (∆Ho), of the system was investigated. Adsorption Kinetic was resolute by Intra particle diffusion (IPD) and Boyd’s models. An attempt was made to prepare (Ag-KCN) nanophoto catalyst by UV light assisted degradation of Malachite Green Oxalate (MGO) dye. They were prepared by the reduction of Ag+ ion under alkaline conditions on kaolin surface. The photo degradation (PD) process was initiated by photo generated electrons. The present study recommended that projected strategies were successfully applied for the remediation of environmental problems. (author)

The efficacy of kaolin clay in reducing the duration and severity of `heat' diarrhea in foals

OpenAIRE

PIESZKA, MAGDALENA; LUSZCZYNSKI, JAROSLAW; HEDRZAK, MAGDALENA; GONCHAROVA, KATERINA; PIERZYNOWSKI, STEFAN G.

2016-01-01

'Heat' diarrhea in foals is an onerous but not life-threatening ailment, which indicates that it may be of osmotic origin. This was confirmed by a successful attempt, presented in this paper, to alleviate the severity and duration of foal heat diarrhea with the use of a typical absorbent, kaolin clay, as a feed additive, usually applied in feed production as an anticaking agent. Based on the present results, it can be concluded that treatment of foals maintained on different stud fa...

Mineralogical characterization and beneficiation study of kaolin from Equador (RN and Junco do Seridó (PB to increase the brightness index

Directory of Open Access Journals (Sweden)

V. M. J. S. Campos

Full Text Available Abstract Kaolin is a rock composed mainly of kaolinite. It is used in many industrial segments, such as paper and ceramics. However, for these uses it is necessary to submit the ore to appropriate beneficiation, which generally involves magnetic separation and chemical bleaching, aiming to remove iron oxide and hydroxide, raising brightness index. This work reports the mineralogical characterization and analysis of the beneficiation of three samples of kaolin, two from Equador (Rio Grande do Norte - RN and the third from Junco do Seridó (Paraíba - PB. The samples were submitted to granulometric classification in sieve of 44 μm, magnetic separation in a magnetic induction of 14000 gauss, and chemical bleaching with sodium dithionite during 240 min. The processes were divided into two beneficiation routes. X-ray diffraction, chemical analysis by X-ray fluorescence and scanning electron microscopy were used for mineralogical characterization of the ore and measurement of the brightness index, while electron paramagnetic resonance was applied to study the variation of iron oxides and hydroxides during beneficiation. The results indicate that just 30 min of chemical bleaching without magnetic separation was sufficient to increase the brightness index from 78.2 to 90.2% and from 91.3 to 95.7% in the two samples from Equador (RN and from 86.9 to 90.4% in the sample from Junco do Seridó (PB. The magnetic separation, although causing a small increase in the brightness index, was inefficient for removal of iron oxides and hydroxides. The results indicated no need for using magnetic separation in plants for beneficiation of kaolin from these two locations, providing the reduction of production costs allowing better exploitation of the ore.

Determination of iron and titanium in kaolins by the method of non-dispersive X-ray fluorescence

International Nuclear Information System (INIS)

Bialy, N.; Kierzek, J.; Parus, J.

1976-01-01

The possibility of application of the radioactive source excited X-ray fluorescence analysis for titanium and iron determination in kaolins to the routine test of the refinement process has been studied. The iron content can be determined with a simple counting system using a single-channel pulse height analyser, argon filled proportional counter and 109 Cd source of 3 mCi for the excitation of K Fe rays. The samples were analyzed both as pellets and powders. The iron content ranged from 0.2-2.5% and titanium from 0.1-0.64%. The best values of precision and determination limit have been achieved for iron with 238 Pu and for titanium with 55 Fe. The precision and accuracy of the X-ray fluorescence method of iron and titanium determination in kaolins are comparable to those of the chemical method. For the simultaneous iron and titanium determination in the discussed region of concentration it is the most advantageous to use the plutonium source with the activity of several tens of mCi and Si(Li) detector with a moderate resolution (250-300 eV for 5.9 keV). The time of the analysis carried out by the described method is several times shorter than the chemical method. The apparatus used in this method is relatively simple, the sample preparation does not require any chemical treatment and the cost of labour of the sample preparation is minimal. (T.G.)

Moisture expansion of ceramic tiles produced using kaolin and granite wastes; Expansao por umidade de revestimentos ceramicos incorporados com residuos de granito e caulim

Energy Technology Data Exchange (ETDEWEB)

Mendonca, A.M.G.D.; Cartaxo, J.M.; Santana, L.N.L; Neves, G.A.; Ferreira, H.C., E-mail: ana.duartemendonca@gmail.com, E-mail: gelmires@dema.ufcg.edu.br, E-mail: lisiane@dema.ufcg.edu.br [Unidade Academica de Engenharia de Materiais, Universidade Federal de Campina Grande,Campina Grande, PB (Brazil); Menezes, R.R. [Departamento de Engenharia de Materiais, Universidade Federal da Paraiba, Joao Pessoa, PB (Brazil)

2012-04-15

Moisture expansion (ME) is the term used to describe the expansion of ceramic materials due to the adsorption of water. ME usually occurs slowly and is relatively small, but, it can damage the ceramic tiles adhesion to the underlayment, craze the glaze and lead to the development of cracks on ceramics bricks. In this work kaolin and granite wastes were incorporated in ceramic compositions aiming study their influence on the ME of ceramic tiles. Raw materials were processed and submitted to characterization: physical and mineralogical by laser diffraction particle size analysis, chemical analysis, thermo differential and thermogravimetric analysis and X-ray diffraction. Results showed that kaolin and granite wastes can be incorporated in ceramic composition because display characteristics similar to conventional not plastic ceramic materials, providing satisfactory ME results when compared to the ME limit value of 0.6 mm/m (0.06%) indicated by the ABNT for ceramic tiles. Compositions containing up to 20% of waste can be produced when firing above 1000 deg C. (author)

Incorporation of waste and fiber kaolin caroa panels in Medium Density Fiberboard - MDF

International Nuclear Information System (INIS)

Bezerra, A.F.C.; Santana, L.N.L.; Neves, G.A.; Carvalho, L.H. de; Lopes, F.F.M.

2012-01-01

Medium-density panels are composites molded under high temperature and pressure which have physical and mechanical properties similar to those of solid wood. Their composition includes eucalyptus grandis fibers and pinus elliotii fibers, but other fibers can be used such as caroa fibers. The goal of this work was to manufacture panels which kaolin waste and caroa fibers and compare their physical, chemical and mechanical of these panels with a others. Both residue and the fibers were characterized by: differential thermal analysis, thermal gravimetric analysis and Xray diffraction. Through the process of pressing the test specimens were fabricated, test samples were evaluated by three point bending, internal bond, water absorption and swelling in thickness. The samples have low levels of thickness swelling, flexural strength and higher tensile and absorption content relative to commercial MDF. (author)

Bulk Fluidity and Apparent Wall Slip of Aqueous Kaolin Suspensions Studied Using the Cone-Cone (KK) Sensor: Effect of the Sensor Surface Quality.

Czech Academy of Sciences Publication Activity Database

Pěnkavová, Věra; Tihon, Jaroslav; Wein, Ondřej

2017-01-01

Roč. 533, NOV 20 (2017), s. 338-346 ISSN 0927-7757 EU Projects: Foundation for Science and Technology(XE) MP1305 Institutional support: RVO:67985858 Keywords : aqueous kaolin suspensions * rotational AWS viscometry * apparent wall slip Subject RIV: CI - Industrial Chemistry, Chemical Engineering OBOR OECD: Chemical process engineering Impact factor: 2.714, year: 2016

Synthesis and characterization of a novel Mg–Al hydrotalcite-loaded kaolin clay and its adsorption properties for phosphate in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Deng, Lin, E-mail: denglinlyn@126.com; Shi, Zhou, E-mail: 369329062@qq.com

2015-07-15

Highlights: • Kaolin clay was coalesced with Mg–Al hydrotalcite to form composite adsorbent (MKC). • MKC was synthesized through modified co-precipitation method. • MKC gave high adsorption of phosphate over a wide pH range of 2.5–9.5. • MKC is an economical and environmentally friendly adsorbent for phosphate removal and recycling. - Abstract: The mesoporous modified kaolin clay (MKC) was synthesized by loading Mg–Al hydrotalcite onto kaolin clay through coprecipitation method and applied for adsorption of phosphate from aqueous solution. Several techniques, including Brunauer–Emmett–Teller (BET), thermal analysis (TG–DTA), and Fourier transform infrared spectroscopy (FTIR) were employed to characterize the adsorbents. The effects of adsorbent dosage, solution pH, initial phosphate concentration, contact time, temperature, and coexistent anions on phosphate adsorption have been investigated. MKC exhibited a strong uptake affinity to phosphate in a wide pH range of 2.5–9.5, with the maximum adsorptive removal of 98.03%, at adsorbent dosage of 0.2 g/50 mL, pH 7.5, and initial phosphate concentration 25 mg L{sup −1}. The adsorption kinetics followed the pseudo-second-order kinetic model. The Langmuir isothermal model well described the adsorption isotherm data, showing a maximum adsorption capacity for phosphate up to 11.92 mg g{sup −1} at 298 K. The obtained thermodynamic parameters revealed that the adsorption of phosphate onto MKC was an exothermic and spontaneous process. Coexistent chloride, nitrate, and sulfate ions displayed an adverse effect on phosphate adsorption following the order of SO{sub 4}{sup 2−} > NO{sub 3}{sup −} > Cl{sup −}. A mechanism of adsorption that involved (i) electrostatic attraction of hydroxyl groups of the adsorbent with negatively charged phosphate ions, and (ii) anion exchange of NO{sub 3}{sup −} ions that were associated with the surface or interlayer of the adsorbent with anionic phosphate ions in

Synthesis and characterization of a novel Mg–Al hydrotalcite-loaded kaolin clay and its adsorption properties for phosphate in aqueous solution

International Nuclear Information System (INIS)

Deng, Lin; Shi, Zhou

2015-01-01

Highlights: • Kaolin clay was coalesced with Mg–Al hydrotalcite to form composite adsorbent (MKC). • MKC was synthesized through modified co-precipitation method. • MKC gave high adsorption of phosphate over a wide pH range of 2.5–9.5. • MKC is an economical and environmentally friendly adsorbent for phosphate removal and recycling. - Abstract: The mesoporous modified kaolin clay (MKC) was synthesized by loading Mg–Al hydrotalcite onto kaolin clay through coprecipitation method and applied for adsorption of phosphate from aqueous solution. Several techniques, including Brunauer–Emmett–Teller (BET), thermal analysis (TG–DTA), and Fourier transform infrared spectroscopy (FTIR) were employed to characterize the adsorbents. The effects of adsorbent dosage, solution pH, initial phosphate concentration, contact time, temperature, and coexistent anions on phosphate adsorption have been investigated. MKC exhibited a strong uptake affinity to phosphate in a wide pH range of 2.5–9.5, with the maximum adsorptive removal of 98.03%, at adsorbent dosage of 0.2 g/50 mL, pH 7.5, and initial phosphate concentration 25 mg L −1 . The adsorption kinetics followed the pseudo-second-order kinetic model. The Langmuir isothermal model well described the adsorption isotherm data, showing a maximum adsorption capacity for phosphate up to 11.92 mg g −1 at 298 K. The obtained thermodynamic parameters revealed that the adsorption of phosphate onto MKC was an exothermic and spontaneous process. Coexistent chloride, nitrate, and sulfate ions displayed an adverse effect on phosphate adsorption following the order of SO 4 2− > NO 3 − > Cl − . A mechanism of adsorption that involved (i) electrostatic attraction of hydroxyl groups of the adsorbent with negatively charged phosphate ions, and (ii) anion exchange of NO 3 − ions that were associated with the surface or interlayer of the adsorbent with anionic phosphate ions in solution, was proposed

Color and shade parameters of ultramarine zeolitic pigments synthesized from kaolin waste

International Nuclear Information System (INIS)

Menezes, Raquel Aranha de; Paz, Simone Patricia Aranha da; Angelica, Romulo Simoes; Neves, Roberto de Freitas; Pergher, Sibele Berenice Castella

2014-01-01

Ultramarine pigments were successful synthesized from zeolite A obtained from kaolin waste. This waste has been used as an excellent source of silicon and aluminum for zeolite synthesis because of its high kaolinite concentrations and low contents of other accessory minerals. The cost is naturally less than the industrialized product. Color additives (Sulfur and Sodium Carbonate) were mixed with different proportions of zeolite A and further calcined for 5 h at 500 °C. They were characterized by XRD and XRF in addition to visual classification by color and shade. These products show colors from blue to green at different shades, both influenced by the amount of additives and cooling rate after calcination. Thus, a different quantity of the same additives in the same zeolitic matrix provides an increase in the color intensity. Cooling rate after calcination induces the color change which is substantially important in the pigments production. (author)

Color and shade parameters of ultramarine zeolitic pigments synthesized from kaolin waste

Energy Technology Data Exchange (ETDEWEB)

Menezes, Raquel Aranha de; Paz, Simone Patricia Aranha da; Angelica, Romulo Simoes; Neves, Roberto de Freitas; Pergher, Sibele Berenice Castella, E-mail: raquel_arn@hotmail.com [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Inst. de Geociencias. Grupo de Mineralogia e Geoquimica Aplicada

2014-08-15

Ultramarine pigments were successful synthesized from zeolite A obtained from kaolin waste. This waste has been used as an excellent source of silicon and aluminum for zeolite synthesis because of its high kaolinite concentrations and low contents of other accessory minerals. The cost is naturally less than the industrialized product. Color additives (Sulfur and Sodium Carbonate) were mixed with different proportions of zeolite A and further calcined for 5 h at 500 °C. They were characterized by XRD and XRF in addition to visual classification by color and shade. These products show colors from blue to green at different shades, both influenced by the amount of additives and cooling rate after calcination. Thus, a different quantity of the same additives in the same zeolitic matrix provides an increase in the color intensity. Cooling rate after calcination induces the color change which is substantially important in the pigments production. (author)

Sintering of anorthite based ceramics prepared from kaolin DD2 and calcite

Energy Technology Data Exchange (ETDEWEB)

Zaiou, S.; Harabi, A.; Harabi, E.; Guechi, A.; Karboua, N.; Benhassine, M.-T.; Zouai, S.; Guerfa, F., E-mail: Zaiou_21@yahoo.fr, E-mail: harabi52@gmail.com, E-mail: semouni84@gmail.com, E-mail: guechia@yahoo.fr, E-mail: kanour17@yahoo.fr, E-mail: mtb25dz@gmail.com, E-mail: zouaisouheila@yahoo.fr, E-mail: guerfatiha@gmail.com [Ceramics Lab., Faculty of Exact Science, Physics Department, Mentouri University of Constantine (Algeria)

2016-10-15

In this work, the preparation of anorthite based ceramics using a modified milling system and 80 wt% kaolin (DD2 type) and 20 wt% calcium oxide extracted from CaCO{sub 3} is shown. The choice of these raw materials was dictated by their natural abundance. Previous studies have shown that a simple and vibratory multidirectional milling system using a bimodal distribution of highly resistant ceramics can be successfully used for obtaining fine powders. The prepared samples were sintered at different temperatures ranging between 800 and 1100 °C. It has been found that the relative density of samples sintered at 900 °C for 1 h with a heating rate of 5 °C/min was about 96% of the theoretical density of anorthite (2.75 g/cm{sup 3} ). Finally, the prepared samples were also characterized by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. (author)

Sintering of anorthite based ceramics prepared from kaolin DD2 and calcite

Directory of Open Access Journals (Sweden)

S. Zaiou

Full Text Available Abstract In this work, the preparation of anorthite based ceramics using a modified milling system and 80 wt% kaolin (DD2 type and 20 wt% calcium oxide extracted from CaCO3 is shown. The choice of these raw materials was dictated by their natural abundance. Previous studies have shown that a simple and vibratory multidirectional milling system using a bimodal distribution of highly resistant ceramics can be successfully used for obtaining fine powders. The prepared samples were sintered at different temperatures ranging between 800 and 1100 °C. It has been found that the relative density of samples sintered at 900 °C for 1 h with a heating rate of 5 °C/min was about 96% of the theoretical density of anorthite (2.75 g/cm3. Finally, the prepared samples were also characterized by scanning electron microscopy, X-ray diffraction and Raman spectroscopy.

Sintering of anorthite based ceramics prepared from kaolin DD2 and calcite

International Nuclear Information System (INIS)

Zaiou, S.; Harabi, A.; Harabi, E.; Guechi, A.; Karboua, N.; Benhassine, M.-T.; Zouai, S.; Guerfa, F.

2016-01-01

In this work, the preparation of anorthite based ceramics using a modified milling system and 80 wt% kaolin (DD2 type) and 20 wt% calcium oxide extracted from CaCO 3 is shown. The choice of these raw materials was dictated by their natural abundance. Previous studies have shown that a simple and vibratory multidirectional milling system using a bimodal distribution of highly resistant ceramics can be successfully used for obtaining fine powders. The prepared samples were sintered at different temperatures ranging between 800 and 1100 °C. It has been found that the relative density of samples sintered at 900 °C for 1 h with a heating rate of 5 °C/min was about 96% of the theoretical density of anorthite (2.75 g/cm 3 ). Finally, the prepared samples were also characterized by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. (author)

Interpretation of the stiffness and permeability of Sand-Kaolin mixtures in the framework of homogenization

Directory of Open Access Journals (Sweden)

Claude Boutin

2010-03-01

Full Text Available This study deals with the behaviour of mixtures of sand and saturated kaolin paste considered as composite materials made of permeable and deformable (with non-linear behaviour matrix (the kaolin paste with rigid and impervious inclusions (the sand grains. Oedometric and permeability tests conducted on such mixtures highlight the key role of the state of the clay paste, and show the existence of a threshold of sand grain concentration above which a structuring effect influences both modulus and permeability. At the light of these experiments, the usual and tangent homogenization process (with simplifying assumptions to make the problem manageable has been applied to estimate the mixture permeability and tangent compressibility. Qualitative and quantitative comparisons with experimental data point out the domain of interest and the limitations of such approaches.O estudo lida com o comportamento de misturas compostas por areia e uma pasta de caulinita considerada um material composto feito de uma matriz (caulinita permeável e deformável (com comportamento não-linear com inclusões rígidas e impermeáveis (grãos de areia. Testes de permeabilidade e odométricos conduzidos nestas misturas enfatizam o papel chave de estado da pasta argilosa e mostram a existência de uma concentração crítica de grãos de areia com efeito estruturante que influencia o módulo e a permeabilidade. Sob a luz destes experimentos o processo de homogeneização usual e tangente (com hipóteses simplificadoras para tornar o problema tratável foi aplicado para estimar a permeabilidade da mistura e a compressibilidade tangente. Comparações qualitativas e quantitativas com dados experimentais apontam o domínio de interesse bem como a limitação destas abordagens.

Mineralizer effects on mullite formation from kaolin processing wastes in Para-Brazil

International Nuclear Information System (INIS)

Martelli, Marlice Cruz; Angelica, Romulo Simoes; Neves, Roberto de Freitas

2009-01-01

Mullite is a relatively rare mineral in nature, formed under exceptional conditions of high temperature and pressure, which can be used to synthesize this mineral. Mullite presents good chemical and thermal stability among others properties that explain the importance of mullite in traditional and advanced ceramics. This research proposes the development of a process to synthesize mullite using the wastes from kaolin processing industries located in the Rio Jari (Monte Dourado-PA) and Rio Capim (Ipixuna-PA) districts. The synthesized materials will be studied for application as silicon-aluminum refractory bricks. The steps are mineralogical and chemical characterization, verifying the differences between the materials processing through firing of the wastes at increasing levels of temperature with 100 deg C increments, ranging from 600 to 1000 deg C and 1200 to 1500 deg C, during 3 hours at each level. Methods include the study of temperature and impurities effects through X-ray-powder and scanning electron microscopy. (author)

Unbelievable but true: Partial thromboplastin time, kaolin 120 s and yet no surgical bleed!

Directory of Open Access Journals (Sweden)

Shagun Bhatia Shah

2017-01-01

Full Text Available Partial thromboplastin time, kaolin (PTTK is a global test sensitive to low levels of all the coagulation factors, except Factor VII and Factor XIII. Patients with extensive cancer have a propensity to develop a shortened PTTK. Our breast cancer patient had a prolonged PTTK result roughly 4 times the normal values. A detailed description of the preoperative workup including the special investigations is required to ascertain the cause of the prolongation and precautions taken, leading to successful breast cancer surgery and postoperative period in this patient follows. Allowing the surgeon to operate a patient with a PTTK >120 s and simultaneously at risk of thrombosis due to lupus anticoagulant is possible with a calculated risk and thorough preoperative evaluation. Prophylactic fresh frozen plasma and deep venous thrombosis prophylaxis have an important role.

Characterization of kaolin and granite waste for formulation of porcelain stoneware tiles; Caracterizacao de caulim e de residuo de granito para formulacao de gres porcelanato

Energy Technology Data Exchange (ETDEWEB)

Luna da Silveira, G.C. [Instituto Federal do Rio Grande do Norte (IFRN), RN (Brazil); Acchar, W.; Gomes, U.U.; Silva, B.K.O.; Luna da Silveira, R.V. [Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil); Labrincha, J.A.; Costa, M.C.P., E-mail: glebacoelli@hotmail.com [Universidade de Aveiro (Portugal)

2016-07-01

To produce a stoneware tiles is necessary develop a formulation that satisfies their structural characteristics, micro-structural, physical and mechanical properties. Thus, in order to create a formulation for porcelain stoneware tiles that give use to kaolin and granite waste used in the production of ceramic materials were asked the following characterizations: chemical analysis, mineralogical, thermal and particle size. We found that in the kaolin sample it presents a rate of silicon oxide and aluminum oxide similar to those found in the work of other investigators, about 45.23% SiO2 and 37.39% Al{sub 2}O{sub 3}. In the granite waste, the percentage of silicon oxide and aluminum oxide are also similar to those observed in other studies, with about 74.89% SiO2 and 10.54% Al{sub 2}O{sub 3}. Both the percentage of SiO{sub 2} and Al{sub 2}O{sub 3} founded in these two samples satisfy the percentage required in the manufacturing of porcelain stoneware tiles. (author)

Magnetic zeolites a and p synthesized from kaolin: synthesis and characterization

Energy Technology Data Exchange (ETDEWEB)

Bessa, R.A.; Oliveira, C.P.; Nascimento, R.F.; Bohn, F.; Loiola, A.R. [Universidade Federal do Ceara (UFCE), CE (Brazil)

2016-07-01

Full text: Zeolites are hydrated aluminosilicates of open chain, formed by silica and alumina tetrahedral structures linked by common oxygen atoms, generating interconnected pores and cages with molecular dimensions and well defined sizes that limit matter transference between internal surface and application medium. They can be found naturally or synthesized using different aluminum and silicon sources that may modify the produced zeolite. Their industrial application has grown enormously over the last century. However, a big issue that still remains is the difficulty in retrieving zeolite powders when used in aqueous media. This work reports the use of kaolin as an alternative raw material for zeolite syntheses by means of hydrothermal route and subsequent preparation of magnetic composites through magnetite impregnation. The syntheses of two different zeolites were carried out by mixing appropriate amounts of metakaolin (kaolin previously calcined at 600 deg C for 2 h), sodium metasilicate and sodium hydroxide solution, aged for 18 h and heated at 100 °C for 4-48 h. After these processes, the final materials were washed several times with distilled water, filtered and dried at 80 deg C for 12 h. Magnetic composites were prepared by impregnating the zeolites with of Fe3O4 nanoparticles (NP) synthesized by the partial oxidation and precipitation of Fe2+ ions. The obtained materials were characterized by X-ray diffraction, scanning electron microscopy, FTIR spectroscopy and magnetization measurements. The results of XRD and FTIR provide evidence of the success in the synthesis of both zeolites A and P as well as Fe3O4. Subsequently, composites were formed by mixtures of zeolite A + NP and zeolite P + NP. The existence of secondary crystalline phases was also confirmed. However, it did not interfered significantly in the results as these phases appear as minor amounts and are most likely residues from the clay used as the main silica and alumina sources. Scanning

Production of zeolite A come from rio Capim Kaolin: Study on recycle of sodium hydroxide solution

International Nuclear Information System (INIS)

Moraes, C.G.; Rodrigues, E.C.; Rocha Junior, C.A.F.; Macedo, E.N.; Neves, R.F.

2011-01-01

The kaolin processing industry is an important economic sector in the State of Para, but produces huge amounts of wastes composed essentially of kaolinite. The production processes of zeolites typically use sodium hydroxide in excess, are discarded. So the objective is the development process for production of zeolite A which allows the reuse of the solution of sodium hydroxide used in excess through your recycling. Presents the results of XRD, SEM of the zeolites produced in five consecutive cycles performed at a temperature of 110°C/24h as a source of sodium hydroxide solution of sodium 5 M, using a molar ratio of Si/Al = 1 and Na/Al = 1,26. (author)

The Effects of Flocculation on the Propagation of Ultrasound in Dilute Kaolin Slurries.

Science.gov (United States)

Austin; Challis

1998-10-01

A broadband ultrasonic spectrometer has been used to measure ultrasonic attenuation and phase velocity dispersion as functions of frequency in kaolin suspensions over a range of solid volume fractions from phi = 0.01 to phi = 0.08 and over a pH range from 3 to 9. The Harker and Temple theory was used to simulate ultrasound propagation in the suspension, using measured slope viscosity, particle size, and size distribution. Simulated results for ultrasonic attenuation and phase velocity agree well with measured values. Both sets of results agree well and show that for volume fractions above phi approximately 0.05 attenuation and velocity dispersion increase for increasing floc size, whereas for volume fractions below phi approximately 0.05 attenuation and velocity dispersion both decrease. It is proposed that the mechanism for this change in behavior around phi approximately 0.05 involves changes in floc density and floc size distribution with phi and pH. Copyright 1998 Academic Press.

Edaravone reduces astrogliosis and apoptosis in young rats with kaolin-induced hydrocephalus.

Science.gov (United States)

Garcia, Camila Araújo Bernardino; Catalão, Carlos Henrique Rocha; Machado, Hélio Rubens; Júnior, Ivair Matias; Romeiro, Thais Helena; Peixoto-Santos, José Eduardo; Santos, Marcelo Volpon; da Silva Lopes, Luiza

2017-03-01

We investigated the possible neuroprotective effects of the free radical scavenger edaravone in experimental hydrocephalus. Seven-day-old Wistar rats were divided into three groups: control group (C), untreated hydrocephalic (H), and hydrocephalic treated with edaravone (EH). The H and EH groups were subjected to hydrocephalus induction by 20% kaolin intracisternal injection. The edaravone (20 mg/kg) was administered daily for 14 days from the induction of hydrocephalus. All animals were daily weighed and submitted to behavioral test and assessment by magnetic resonance imaging. After 14 days, the animals were sacrificed and the brain was removed for histological, immunohistochemical, and biochemical studies. The gain weight was similar between groups from the ninth post-induction day. The open field test performance of EH group was better (p  0.01), germinal matrix (p > 0.05), and cerebral cortex (p > 0.05), as compared to H group. We have demonstrated that administration of edaravone for 14 consecutive days after induction of hydrocephalus reduced astrocyte activity and that it has some beneficial effects over apoptotic cell death.

Influence of inert fillers on shrinkage cracking of meta-kaolin geo-polymers

International Nuclear Information System (INIS)

Kuenzel, C.; Boccaccini, A.R.

2012-01-01

Geo-polymers contain a network of tetrahedral coordinated aluminate and silicate, and are potential materials to immobilize/encapsulate nuclear wastes. They can exhibit shrinkage cracking when water is removed by drying, and in order to use geo-polymers for waste encapsulation this effect needs to be investigated and controlled. In this study, six different fillers were mixed with meta-kaolin and sodium silicate solution at high pH to form geo-polymers, and the influence of filler addition on mechanical properties has been determined. The fillers used were Fe 2 O 3 , Al 2 O 3 , CaCO 3 , sand, glass and rubber and these do not react during geo-polymerisation reactions. Geo-polymers were prepared containing 30 weight percent of filler. The mechanical properties of the geo-polymers were influenced by the type of filler, with low density fillers increasing mortar viscosity. Geo-polymer samples containing fine filler particles exhibited shrinkage cracking on drying. This was not observed when coarser particles were added and these samples also had significantly improved mechanical properties. (authors)

Bulk Fluidity and Apparent Wall Slip of Aqueous Kaolin Suspensions Studied Using the Cone-cone (KK) Sensor: The Effect of Concentration and Temperature.

Czech Academy of Sciences Publication Activity Database

Pěnkavová, Věra; Tihon, Jaroslav; Wein, Ondřej

2016-01-01

Roč. 511, DEC 20 (2016), s. 272-284 ISSN 0927-7757 R&D Projects: GA MŠk(CZ) LD13018 Grant - others:COST- European Coperation in Science and Technology(XE) MP1305; COST- European Coperation in Science and Technology(XE) MP1106 Program:LD COST Institutional support: RVO:67985858 Keywords : aqueous kaolin suspensions * apparent wall slip * cone-cone (KK) sensor Subject RIV: CI - Industrial Chemistry , Chemical Engineering Impact factor: 2.714, year: 2016

Effects of using kaolin waste and granite waste as raw materials for the production of low-water absorption ceramic tiles; Efeitos da co-utilizacao dos residuos do beneficiamento do caulim e da extracao do granito rain forest para a producao de revestimentos ceramicos com baixa absorcao de agua

Energy Technology Data Exchange (ETDEWEB)

Freires, H.P.; Argonz, R.; Nogueira, R.E.F.Q.; Sasaki, J.M., E-mail: argonz@ufc.br [Universidade Federal do Ceara (UFC), Fortaleza, CE (Brazil); Sales, J.C. [Universidade do Vale do Aracau (UVA), Crateus, CE (Brazil)

2012-07-01

This study aims to evaluate the potential of co-use of granite waste (Rain Forest) and kaolin waste as raw material for the manufacture of ceramic coating of low water absorption. Raw materials were characterized by X-ray diffraction. Kaolin residue was added to the residue of granite in the following proportions (in wt%): 0, 10, 20, 30, 40 and 50%. Specimens were fabricated by uniaxial pressing and fired at 1175,1200 and 1225 deg C. Studies of firing linear shrinkage, water absorption, apparent porosity, apparent density and tensile bending test (or rupture modulus) were conducted. The temperature of 1225 deg C allowed the use of a mixture of 50% granite residue and 50% kaolin residue. Ceramic parts made from that mixture exhibited the maximum values required by the Brazilian Standard NBR 13818 for water absorption, shrinkage and density. (author)

Kinetic study of formation of sodalite from a kaolin waste of Jari river - PA, Brazil

International Nuclear Information System (INIS)

Silva, L.N. da; Paz, S.P.A. da; Angelica, R.S.; Neves, R.F.

2011-01-01

Zeolites are materials with a wide industrial application, which has motivated the development of a large number of scientific papers on this topic. This work presents a kinetic study of the formation process of sodalite produced from the reaction of the kaolin waste in the presence of sodium hydroxide solution (5M) performed at temperatures of 80, 100, 120 and 150 ° C. The process was conducted in batch, static, and autoclaves lined with Teflon, and monitoring the kinetics was performed by ex situ XRD analysis of the materials obtained in the time interval from 2 to 24 hours. The kinetic model that best describes this transformation is zero-order homogeneous reaction. Finally, we conclude that the technique of X-ray diffraction is a powerful tool to study the kinetics of phase transformation ex situ. (author)

Atividade pozolânica dos resíduos do beneficiamento do caulim para uso em argamassas para alvenaria Pozolanic activity of kaolin processing residues for use in masonry mortars

Directory of Open Access Journals (Sweden)

Romualdo R. Menezes

2009-12-01

Full Text Available A indústria do beneficiamento do caulim gera enorme quantidade de resíduos, descartados indiscriminadamente no meio ambiente; assim, este trabalho tem por objetivo analisar a viabilidade técnica e a atividade pozolânica dos resíduos do beneficiamento do caulim para a produção de argamassas. Os resíduos foram caracterizados através da determinação de sua distribuição granulométrica e composição química, difração de raios X e análise térmica diferencial e gravimétrica; em seguida, determinou-se o índice de atividade pozolânica dos resíduos de caulim com a cal e o cimento Portland. Argamassas de cimento:cal:areia foram preparadas e o resíduo, na condição natural e após queima a 600 °C por 2 h, substituiu parcialmente o cimento nas proporções de 5, 10, 15 e 20% em massa. Corpos-de-prova foram moldados e determinada sua resistência a compressão simples. Conclui-se, com base nos resultados, que os resíduos são constituídos de caulinita, mica e quartzo e que a utilização do resíduo calcinado aumenta a resistência das argamassas após 28 dias de cura em até 150%.The kaolin processing industry generates large amounts of waste, which is indiscriminately dumped in open-air sites. This work evaluates the technical suitability and pozolanic activity of kaolin processing wastes for the production of mortars. The wastes were characterized by particle size distribution and chemical composition determination, X-ray diffraction and thermal differential and gravimetric analyses. The pozolanic activity index was determined using lime and Portland cement. Cement:lime:sand mortars were formulated and the kaolin wastes replaced cement by 5, 10, 15 and 20% on weight basis. The kaolin wastes were used in their natural condition and after thermal treatment at 600 °C for 2 h. Test specimens were produced and their compression strength determined. The results indicated that the waste consists of quartz, kaolinite and mica, and

Multiple scattering wavelength dependent backscattering of kaolin dust in the IR: Measurements and theory

Science.gov (United States)

Ben-David, Avishai

1992-01-01

Knowing the optical properties of aerosol dust is important for designing electro-optical systems and for modeling the effect on propagation of light in the atmosphere. As CO2 lidar technology becomes more advanced and is used for multiwavelength measurements, information on the wavelength dependent backscattering of aerosol dust particles is required. The volume backscattering coefficient of aerosols in the IR is relatively small. Thus, only a few field measurements of backscattering, usually at only a few wavelengths, are reported in the literature. We present spectral field measurements of backscattering of kaolin dust in the 9-11 micron wavelength range. As the quantity of dust increases, multiple scattering contributes more to the measured backscattered signal. The measurements show the effect of the dust quantity of the spectral backscatter measurements. A simple analytical two stream radiative transfer model is applied to confirm the measurements and to give insight to the multiple scattering spectra of backscattering.

Effect of temperature on volume change behaviour of statically compacted kaolin clay

Directory of Open Access Journals (Sweden)

Ileme Ogechi

2016-01-01

Full Text Available Several soils are subjected to high temperature due to the environment where they are located or activities around them. For instance, upper layer of soils in tropical regions, soils around geothermal structures, clay barriers around nuclear waste repository systems. Numerous studies have pointed out that high temperature affects the hydro-mechanical properties of soils. Notwithstanding already existing studies, the influence of temperature on soils is still a challenge, as most of these studies are soil specific and cannot be inferred as the behaviour of all soils. This paper presents an experimental study on the influence of temperature on the volume change behaviour of statically compacted kaolin clay. Compacted samples were tested at varying temperatures using a suction controlled oedometer cell. The influence of temperature on the magnitude of volumetric strain occurring during mechanical and thermal loading was investigated. The study showed that an increase in temperature increased the magnitude of volumetric strain of the soil on loading. Additionally, the results presented in the light of LC curve showed that an increase in temperature resulted in the contraction and a change in the position of the LC curve.

Effect of kaolin treatment temperature on mortar chloride permeability

Directory of Open Access Journals (Sweden)

Puertas, F.

2007-03-01

Full Text Available The present paper discusses the results of chloride resistance tests conducted on ordinary Portland cement (OPC mortars containing a Colombian kaolin pre-treated at temperatures of from 600 to 800 ºC. The resulting metakaolin (MK was added to OPC mortar mixes in proportions of 10 and 20% by cement weight. The mortars were compared for physical and chemical properties, including capillary absorption, chloride permeability and pore microstructure as assessed by mercury porosimetry. The best performance was recorded for the samples containing 20% of the material treated at 800 ºC.En el presente trabajo se incluyen los resultados de la resistencia a la penetración de cloruros de morteros de Cemento Portland Ordinario (OPC adicionados con un caolín colombiano sometido a tratamiento térmico en un rango de temperaturas entre 600 y 800 °C. Los productos del tratamiento térmico, metacaolín (MK, son incorporados en mezclas de morteros de OPC en proporciones del 10 y 20% en relación al peso del cemento. Se comparan sus características físico-químicas, entre las cuales se incluye la microestructura de poros evaluada por la técnica de porosimetría de mercurio, con la absorción capilar y la permeabilidad a cloruros. Se concluye que las muestras adicionadas con un 20% del material tratado térmicamente a 800 °C presentan el mejor desempeño en sus propiedades finales.

Heavy mineral as a tool to refine the stratigraphy of kaolin deposits in the Rio Capim Area, Northern Brazil

Directory of Open Access Journals (Sweden)

Ana M. Góes

2007-09-01

Full Text Available Studies of heavy minerals in kaolin deposits from the Ipixuna Formation in the Rio Capim area (Northern Brazil showed a mature to super mature assemblage dominated by zircon and tourmaline, and subordinately rutile, kyanite and staurolite. These minerals do not change much throughout the whole section; however, each kaolin unit displays a particular signature, defined by differences in the proportions of the whole assemblage of heavy minerals, as well as of their textural characteristics. This work revealed that the lower and upper kaolin units can be definitely considered as distinct depositional sequences. A higher proportion of opaque minerals and higher zircon values characterize the lower unit. The higher volumes of anhedric, rounded to sub-rounded grains of zircon and tourmaline in the upper unit suggests that this includes grains that were undergone to a higher degree of reworking. The increased volume of unaltered staurolite and kyanite in the upper unit leads to conclude that, even considering sediment reworking, a distinct source must be invoked. The results also show that the characteristics of the heavy mineral assemblage from the intermediate unit are comparable with those from the upper unit, which suggests they might record a same stratigraphic sequence.Estudos de minerais pesados provenientes em depósitos cauliníticos da Formação Ipixuna na região do rio Capim (Brasil revelaram uma mineralogia matura a supermatura, representada dominantemente por zircão e turmalina e, subordinadamente, rutilo, cianita e estaurolita. Os minerais encontrados não variam muito, entretanto cada unidade caulinítica apresenta uma assinatura particular definida por diferenças nasproporções entre os principais minerais, assim como em suas características texturais. Este trabalho demonstrou que asunidades de caulim soft (inferior e semi-flint (superior podem ser consideradas seqüências deposicionais distintas. As altas percentagens de opacos

Cationic polyelectrolyte induced separation of some inorganic contaminants and their mixture (zirconium silicate, kaolin, K-feldspar, zinc oxide) as well as of the paraffin oil from water.

Science.gov (United States)

Ghimici, Luminita

2016-03-15

The flocculation efficiency of a cationic polyelectrolyte with quaternary ammonium salt groups in the backbone, namely PCA5 was evaluated on zirconium silicate (kreutzonit), kaolin, K- feldspar and zinc oxide (ZnO) suspensions prepared either with each pollutant or with their mixture. The effect of several parameters such as settling time, polymer dose and the pollutant type on the separation efficacy was evaluated and followed by optical density and zeta potential measurements. Except for ZnO, the interactions between PCA5 and suspended particles led to low residual turbidity values (around 4% for kreutzonit, 5% for kaolin and 8% for K-feldspar) as well as to the reduction of flocs settling time (from 1200 min to 30 min and 120 min in case of kaolinit and K-feldspar, respectively), that meant a high efficiency in their separation. The negative value of the zeta potential and flocs size measurements, at the optimum polymer dose, point to contribution from charge patch mechanism for the particles flocculation. A good efficiency of PCA5 in separation of paraffin oil (a minimum residual turbidity of 9.8%) has been also found. Copyright © 2015 Elsevier Ltd. All rights reserved.

The effects of sucralfate suspension and diphenhydramine syrup plus kaolin-pectin on radiotherapy-induced mucositis

International Nuclear Information System (INIS)

Barker, G.; Loftus, L.; Cuddy, P.; Barker, B.

1991-01-01

A prospective, double-blind study compared the effectiveness of sucralfate suspension with diphenhydramine syrup plus kaolin-pectin in reducing severity and pain of radiation-induced oropharyngeal mucositis. Fourteen patients who received at least 4600 cGy to the oral cavity used one of the mouth rinses four times a day, beginning at 1600 cGy. Data were collected on daily perceived pain and helpfulness of mouth rinse, weekly mucositis grade, weight change, and interruption of therapy. Analysis of data revealed no statistically significant differences between the two groups in any parameter. A retrospective review of 15 patients who had received at least 4600 cGy radiation to the oropharynx but had not used a daily mouth-coating rinse, was compared with the study group. Comparison of the two groups suggested that consistent daily oral hygiene and use of a mouth-coating agent will result in less pain and may reduce weight loss and interruption of radiation because of severe mucositis

The effects of sucralfate suspension and diphenhydramine syrup plus kaolin-pectin on radiotherapy-induced mucositis

Energy Technology Data Exchange (ETDEWEB)

Barker, G.; Loftus, L.; Cuddy, P.; Barker, B. (Univ. of Missouri, Kansas City (USA))

1991-03-01

A prospective, double-blind study compared the effectiveness of sucralfate suspension with diphenhydramine syrup plus kaolin-pectin in reducing severity and pain of radiation-induced oropharyngeal mucositis. Fourteen patients who received at least 4600 cGy to the oral cavity used one of the mouth rinses four times a day, beginning at 1600 cGy. Data were collected on daily perceived pain and helpfulness of mouth rinse, weekly mucositis grade, weight change, and interruption of therapy. Analysis of data revealed no statistically significant differences between the two groups in any parameter. A retrospective review of 15 patients who had received at least 4600 cGy radiation to the oropharynx but had not used a daily mouth-coating rinse, was compared with the study group. Comparison of the two groups suggested that consistent daily oral hygiene and use of a mouth-coating agent will result in less pain and may reduce weight loss and interruption of radiation because of severe mucositis.

Equilibrium, kinetic and thermodynamic studies of adsorption of Th(IV) from aqueous solution onto kaolin

International Nuclear Information System (INIS)

Hongxia Zhang; Zhiwei Niu; Zhi Liu; Zhaodong Wen; Weiping Li; Xiaoyun Wang; Wangsuo Wu

2015-01-01

The kinetics and thermodynamics of the adsorption of Th(IV) on the kaolin were studied by using batch method. In addition, the experimental data were studied by dynamic and thermodynamic models. The results showed that the adsorption capacity of the adsorbent increased with increasing temperature and solid liquid ratio, but decreased with increasing initial Th(IV) ion concentration, and the best fit was obtained for the pseudo-second-order kinetics model. The calculated activation energy for adsorption was about 45 kJ/mol, which indicated the adsorption process to be chemisorption. The adsorption isotherm data could be well described by the Langmuir as well as Dubinin-Radushkevich model. The mean free energy (E) of adsorption was calculated to be about 15 kJ/mol. The thermodynamic data calculated showed that the adsorption was spontaneous and enhanced at higher temperature. Considering kinetics and equilibrium studies, the adsorption on the sites was the rate-limiting step and that adsorption was mainly a chemisorption process through cation exchange. (author)

Fabrication of recyclable and durable superhydrophobic materials with wear/corrosion-resistance properties from kaolin and polyvinylchloride

Science.gov (United States)

Qu, Mengnan; Liu, Shanshan; He, Jinmei; Feng, Juan; Yao, Yali; Ma, Xuerui; Hou, Lingang; Liu, Xiangrong

2017-07-01

In this study, mechanically stable and recyclable superhydrophobic materials were prepared from polyvinylchloride (PVC) and kaolin nanoparticles modified by stearic acid using a simple and low-cost drop-coating. The obtained materials displayed liquid-repellent toward water and several other liquids of daily life (such as orange juice, coffee, milk, coca cola and ink). These superhydrophobic materials showed remarkable robustness against sandpaper abrasion, UV-irradiation and ultrasonication test, while retaining its superhydrophobicity even after 60 abrasion cycles loaded of 500 g with sandpaper, 7 days UV-irradiation or 120 min ultrasonication test. The excellent durability against complex conditions was attributed to the hierarchical structure and strong interfacial adhesion of the materials. More significantly, the materials used in the coating could be recycled and reconstructed without losing its superhydrophobicity. The current superhydrophobic materials tolerate rigorous environment, opening a new avenue to a variety of practical applications.

Mechanical properties of anorthite based ceramics prepared from kaolin DD2 and calcite

Energy Technology Data Exchange (ETDEWEB)

Harabi, A.; Zaiou, S.; Guechi, A.; Foughali, L.; Harabi, E.; Karboua, N.-E.; Zouai, S.; Mezahi, F.-Z.; Guerfa, F., E-mail: harabi52@gmail.com, E-mail: Zaiou_21@yahoo.fr, E-mail: guechia@yahoo.fr, E-mail: semouni84@gmail.com, E-mail: kanour17@yahoo.fr, E-mail: foughali_lazhar@yahoo.fr, E-mail: zouaisouheila@yahoo.fr, E-mail: mezahif@yahoo.fr [Ceramics Lab., Faculty of Exact Science, Physics Department, Mentouri University of Constantine (Algeria)

2017-07-15

Good quality ceramics costs a lot that has limited their use in developing countries. This work was devoted to prepare low-cost and good quality anorthite based ceramics. The proposed composition was 80 wt% kaolin (DD2 type) and 20 wt% calcium oxide (CaO). The choice of these raw materials was dictated by their natural abundance coupled with a modified milling system, as another interesting advantage. Previous studies have shown that a simple vibratory multidirectional milling system using bimodal distribution of highly resistant ceramic milling elements has been successfully applied for obtaining fine powders. The influence of the relatively lower sintering temperature, ranging from 800 to 1100 °C, on the porosity and the average pore size (APS) have been investigated. The APS and the porosity values of samples sintered at 950 °C were about 1 μm and 4%, respectively. The best Vickers microhardness and 3-point bending strength values for these sintered samples, using this proposed milling system, were 7.1 GPa and 203 MPa, respectively. Finally, the crystalline phase evolution during heat treatment was investigated by X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy techniques. (author)

Infrared Spectroscopic Study on Structural Change and Interfacial Interaction in Rubber Composites Filled with Silica-Kaolin Hybrid Fillers

Science.gov (United States)

Chen, Y.; Guan, J.; Hu, H.; Gao, H.; Zhang, L.

2016-07-01

A series of natural rubber/styrene butadiene rubber/polybutadiene rubber composites was prepared with nanometer silica and micron kaolin by a dry modification process, mechanical compounding, and mold vulcanization. Fourier transform infrared spectroscopy and a scanning electron microscope were used to investigate the structural changes and interfacial interactions in composites. The results showed that the "seesaw" structure was formed particularly with the incorporation of silica particles in the preparation process, which would be beneficial to the dispersibility of fillers in the rubber matrix. The kaolinite platelets were generally arranged in directional alignment. Kaolinite with smaller particle size and low-defect structure was more stable in preparation, but kaolinite with larger particle size and high defect structure tended to change the crystal structure. The composite prepared in this research exhibited excellent mechanical and thermal properties.

Elma Bahçelerinde Bazı Önemli Zararlılara Karşı Azadirachtin ve Kaolin Uygulamalarının Etkisi

Directory of Open Access Journals (Sweden)

Nazım KÜÇÜKBALLI

2018-02-01

Full Text Available Elma bahçelerinde ekonomik kayıplara neden olan birçok hastalık, zararlı ve yabancıot türü bulunmaktadır. Zararlılar içinde elma içkurdu, kırmızıörümcekler ve yaprakbitleri ana zararlılar arasında yer almaktadır. Elma üretiminin yoğun yapıldığı Isparta ilinde özellikle yağışlı geçen yıllarda yılda 20 kezden daha fazla ilaçlama yapıldığı bilinmektedir. Bu çalışmada söz konusu zararlılara karşı çevre ve yararlılara fazla etkisi olmadığı bilinen azadirachtin ve kaolinin etkisi 2015 yılında incelenmiştir. Denemeler Süleyman Demirel Üniversitesi, Ziraat Fakültesi bünyesinde bulunan 5 ve 2 dekarlık iki elma bahçesinde yürütülmüştür. Her bahçe dört parsele ayrılmış ve her bir parsele kaolin, azadirachtin (neem, karşılaştırma ilacı olarak chlorpyrifos-ethyl ve Kontrol parseline de su püskürtme şeklinde uygulanmıştır. Denemeler tesadüf blokları deneme desenine göre kurulmuş olup, her tekerrürde 8 ağaç olacak şekilde 6 tekerrürlü olarak düzenlenmiştir. Her hafta, her bir ağaçtan 40 yaprak örneği alınarak Tetranychus urticae, Pananychus ulmi, Aphis pomi ve Dysaphis plantaginea sayımları yapılmıştır. Elma içkurdu zararı ise hasat zamanında ağaç üzerinde ve yere düşen meyvelerde bulaşma oranına göre belirlenmiştir. Çalışma sonucunda yaprakbitine karşı en etkili Chlorpyrifos-ethyl bulunmuş, bunu kaolin ve neem izlemiştir. Preparatlar kırmızıörümceklere karşı benzer etki gösterirken elma içkurdu bulaşma oranları sırasıyla, kontrol parselinde %49.99, kaolin parselinde %42.27, neem parselinde %41.20 ve chlorpyrifos-ethyl parselinde %31.23 olmuştur.

Synthesis of Al4SiC4 powders from kaolin grog, aluminum and carbon black by carbothermal reaction

Science.gov (United States)

Yuan, Wenjie; Yu, Chao; Deng, Chengji; Zhu, Hongxi

2013-12-01

In this paper, the synthesis of Al4SiC4 used as natural oxide materials by carbothermal reduction was investigated in order to explore the synthesis route with low costs. The samples were calcined by using kaolin grog, aluminum and carbon black as raw materials with the selected proportion at the temperature from 1500 to 1800 ° C for 2 hours under flow argon atmosphere. The phase composition of reaction products were determined by X-ray diffraction. The microstructure and elemental composition of different phases were observed and identified by scanning electron microscopy and energy dispersive spectroscopy. The mechanism of reaction processing was discussed. The results show that Al4SiC4 powders composed of hexagonal plate-like particulates with various sizes and the thickness of less than 20 μm are obtained when the temperature reaches 1800 °C.

Synthesis of Al4SiC4 powders from kaolin grog, aluminum and carbon black by carbothermal reaction

International Nuclear Information System (INIS)

Yuan, Wenjie; Yu, Chao; Deng, Chengji; Zhu, Hongxi

2013-01-01

In this paper, the synthesis of Al 4 SiC 4 used as natural oxide materials by carbothermal reduction was investigated in order to explore the synthesis route with low costs. The samples were calcined by using kaolin grog, aluminum and carbon black as raw materials with the selected proportion at the temperature from 1500 to 1800 ° C for 2 hours under flow argon atmosphere. The phase composition of reaction products were determined by X-ray diffraction. The microstructure and elemental composition of different phases were observed and identified by scanning electron microscopy and energy dispersive spectroscopy. The mechanism of reaction processing was discussed. The results show that Al 4 SiC 4 powders composed of hexagonal plate-like particulates with various sizes and the thickness of less than 20 μm are obtained when the temperature reaches 1800 °C

Phase modification and dielectric properties of a cullet-paper ash-kaolin clay-based ceramic

Science.gov (United States)

Samah, K. A.; Sahar, M. R.; Yusop, M.; Omar, M. F.

2018-03-01

Novel ceramics from waste material made of ( x) paper ash-(80 - x) cullet-20 kaolin clay (10wt% ≤ x ≤ 30wt%) were successfully synthesized using a conventional solid-state reaction technique. Energy-dispersive X-ray analysis confirmed the presence of Si, Ca, Al, and Fe in the waste material for preparing these ceramics. The influence of the cullet content on the phase structures and the dielectric properties of these ceramics were systematically investigated. The impedance spectra were verified in the range from 1 Hz to 10 MHz at room temperature. The phase of the ceramics was found to primarily consist of wollastonite (CaSiO3), along with minor phases of γ-dicalcium silicate (Ca2SiO4) and quartz (SiO2). The sample with a cullet content of 55wt% possessed the optimum wollastonite structure and exhibited good dielectric properties. An increase of the cullet content beyond 55wt% resulted in a structural change from wollastonite to dicalcium silicate, a decrease in dielectric constant, and an increase in dielectric loss. All experimental results suggested that these novel ceramics from waste are applicable for electronic devices.

Hydrothermal synthesis of zeolite T from kaolin using two different structure-directing agents

Science.gov (United States)

Arshad, Sazmal E.; Lutfor Rahman, M.; Sarkar, Shaheen M.; Yusslee, Eddy F.; Patuwan, Siti Z.

2018-01-01

Zeolite T was synthesized from the molar chemical composition of 1SiO2:0.04Al2O3:0.26Na2O:0.09K2O:14H2O in the form of a homogenous milky solution in the presence of the two different structure-directing agents TMAOH and TEAOH respectively. Modification of the composition of silica was undertaken using metakaolin from calcined kaolin at 750 °C for 4 h, while the molar composition of each different SDA was variated from 0.05, 0.10, 0.15, 0.20 and 0.25. The homogenous mixture was left at room temperature for 24 h before undergoing hydrothermal synthesis at 100 °C for 168 h. The synthesized samples were filtered and aged at 120 °C for 2 h and each sample was calcined at high temperatures (545 °C for TMAOH and 520 °C for TEAOH) for template removal before characterization using XRD and SEM. Crystallization of the zeolite T in its major form only took place at a molar ratio of 0.10 of TMAOH, while TEAOH showed the species evolution of zeolite T into zeolite L and W for other molar ratios.

Preparation and solar-light photocatalytic activity of TiO2 composites: TiO2/kaolin, TiO2/diatomite, and TiO2/zeolite

Science.gov (United States)

Li, Y.; Li, S. G.; Wang, J.; Li, Y.; Ma, C. H.; Zhang, L.

2014-12-01

Three TiO2 loaded composites, TiO2/kaolin, TiO2/diatomite, and TiO2/zeolite, were prepared in order to improve the solar-light photocatalytic activity of TiO2. The results showed that the photocatalytic activity could obviously be enhanced by loading appropriate amount of inorganic mineral materials. Meanwhile, TiO2 content, heat-treatment temperature and heat-treatment time on the photocatalytic activity were reviewed. Otherwise, the effect of solar light irradiation time and dye concentration on the photocatalytic degradation of Acid Red B was investigated. Furthermore, the degradation mechanism and adsorption process were also discussed.

Synthesis, characterization and application of nanozeolite NaX from Vietnamese kaolin

International Nuclear Information System (INIS)

Ngoc, Don Ta; Pham, Thanh Huyen; Hong Nguyen, Khanh Dieu

2013-01-01

This paper presents the results of synthesis of nanozeolite NaX from Vietnamese kaolin. Influence factors on the control of crystal sizes and application of synthesized materials as adsorbent for organic compound are discussed. The results show that there are several factors that influence the synthesis. When water content in gel increases, crystal size of NaX increases sharply. The increase of alkaline and silica contents increases the crystallinity and decreases the particle size of nano NaX, and the particle size reaches the minimum at Na 2 O/Al 2 O 3 = 5.0 and SiO 2 /Al 2 O 3 = 4.0. Crystal sizes formed at low crystallizing temperature are smaller than those formed at higher temperature. Ageing time and crystallizing time strongly influence the crystallinity and crystal size, which is related to the number of crystal seeds formed during ageing period, the growth of seed and the partial solubility of crystal at maximum formation. Nano NaX was characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET) adsorption, Fourier transform infrared (FTIR) and simultaneous thermogravimetry–differential scanning calorimetry (TG/DSC). At optimized synthesis conditions, nano NaX has surface area of 573 m 2 g −1 with external surface area of 92 m 2 g −1 , pore size distribution at 0.81 and 10.8 nm, average crystal size of 25 nm and thermal stability up to 789 °C. This material can adsorb cumene rapidly with high adsorption capacity and stability. (paper)

X-ray shielding behaviour of kaolin derived mullite-barites ceramic

Science.gov (United States)

Ripin, A.; Mohamed, F.; Choo, T. F.; Yusof, M. R.; Hashim, S.; Ghoshal, S. K.

2018-03-01

Mullite-barite ceramic (MBC) is an emergent material for effective shielding of redundant ionizing radiation exposure. The composition dependent mechanical, thermal, and microstructure properties of MBC that makes MBC a high performing novel radiation shielding candidate remained unexplored. This paper examines the possibility of exploiting Malaysian kaolin (AKIM-35) and barite (BaSO4) derived ceramic (MBC) system for X-ray shielding operation. Using conventional pressing and sintering method six ceramic samples are prepared by mixing AKIM-35 with barite at varying contents (0, 10, 20, 30, 40 and 50 wt%). Synthesized pressed mixtures are calcined at 400 °C for 30 min and then sintered to 1300 °C for 120 min at a heating rate of 10 °C/min. Sintered samples are characterized via X-ray Diffraction (XRD), Field Emission Scanning Electron Microscope (FESEM), lead equivalent (LE), uniformity and dose reduction analyses. XRD pattern of prepared ceramics revealed the presence of monoclinic barium alumino-silicate (BAS) and orthorhombic mullite as major shielding phases together with other minor phase of barite and hexagonal quartz (SiO2) structures. Furthermore, FESEM images of ceramics (between 0 and 30 wt%) displayed the existence of compacted monoclinic plate of BAS and acicular mullite morphology (ceramics at 40 and 50 wt%). Radiation tests displayed the capacity of ceramics (at 0 and 10 wt%) to shield the X-ray radiation emanated at tube potential range of 50-120 kV. The highest radiation attenuation is ascertained at 70 kV where the dose is reduced remarkably between 99.11% and 97.42%. Ceramics at 0 and 10 wt% demonstrated the highest lead (Pb) equivalent thickness (LE) of 0.44 mm and 0.34 mm, respectively. It is established that such MBC may contribute towards the development of shielding material against ionizing radiation in diagnostic radiology (X-ray) dose range.

Magnetic resonance imaging indicators of blood-brain barrier and brain water changes in young rats with kaolin-induced hydrocephalus.

Science.gov (United States)

Del Bigio, Marc R; Slobodian, Ili; Schellenberg, Angela E; Buist, Richard J; Kemp-Buors, Tanya L

2011-08-11

Hydrocephalus is associated with enlargement of cerebral ventricles. We hypothesized that magnetic resonance (MR) imaging parameters known to be influenced by tissue water content would change in parallel with ventricle size in young rats and that changes in blood-brain barrier (BBB) permeability would be detected. Hydrocephalus was induced by injection of kaolin into the cisterna magna of 4-week-old rats, which were studied 1 or 3 weeks later. MR was used to measure longitudinal and transverse relaxation times (T1 and T2) and apparent diffusion coefficients in several regions. Brain tissue water content was measured by the wet-dry weight method, and tissue density was measured in Percoll gradient columns. BBB permeability was measured by quantitative imaging of changes on T1-weighted images following injection of gadolinium diethylenetriamine penta-acetate (Gd-DTPA) tracer and microscopically by detection of fluorescent dextran conjugates. In nonhydrocephalic rats, water content decreased progressively from age 3 to 7 weeks. T1 and T2 and apparent diffusion coefficients did not exhibit parallel changes and there was no evidence of BBB permeability to tracers. The cerebral ventricles enlarged progressively in the weeks following kaolin injection. In hydrocephalic rats, the dorsal cortex was more dense and the white matter less so, indicating that the increased water content was largely confined to white matter. Hydrocephalus was associated with transient elevation of T1 in gray and white matter and persistent elevation of T2 in white matter. Changes in the apparent diffusion coefficients were significant only in white matter. Ventricle size correlated significantly with dorsal water content, T1, T2, and apparent diffusion coefficients. MR imaging showed evidence of Gd-DTPA leakage in periventricular tissue foci but not diffusely. These correlated with microscopic leak of larger dextran tracers. MR characteristics cannot be used as direct surrogates for water

Magnetic resonance imaging indicators of blood-brain barrier and brain water changes in young rats with kaolin-induced hydrocephalus

Directory of Open Access Journals (Sweden)

Del Bigio Marc R

2011-08-01

Full Text Available Abstract Background Hydrocephalus is associated with enlargement of cerebral ventricles. We hypothesized that magnetic resonance (MR imaging parameters known to be influenced by tissue water content would change in parallel with ventricle size in young rats and that changes in blood-brain barrier (BBB permeability would be detected. Methods Hydrocephalus was induced by injection of kaolin into the cisterna magna of 4-week-old rats, which were studied 1 or 3 weeks later. MR was used to measure longitudinal and transverse relaxation times (T1 and T2 and apparent diffusion coefficients in several regions. Brain tissue water content was measured by the wet-dry weight method, and tissue density was measured in Percoll gradient columns. BBB permeability was measured by quantitative imaging of changes on T1-weighted images following injection of gadolinium diethylenetriamine penta-acetate (Gd-DTPA tracer and microscopically by detection of fluorescent dextran conjugates. Results In nonhydrocephalic rats, water content decreased progressively from age 3 to 7 weeks. T1 and T2 and apparent diffusion coefficients did not exhibit parallel changes and there was no evidence of BBB permeability to tracers. The cerebral ventricles enlarged progressively in the weeks following kaolin injection. In hydrocephalic rats, the dorsal cortex was more dense and the white matter less so, indicating that the increased water content was largely confined to white matter. Hydrocephalus was associated with transient elevation of T1 in gray and white matter and persistent elevation of T2 in white matter. Changes in the apparent diffusion coefficients were significant only in white matter. Ventricle size correlated significantly with dorsal water content, T1, T2, and apparent diffusion coefficients. MR imaging showed evidence of Gd-DTPA leakage in periventricular tissue foci but not diffusely. These correlated with microscopic leak of larger dextran tracers. Conclusions MR

Study on the NaOH/metakaolin ratio and crystallization time for zeolite a synthesis from kaolin using statistical design

Energy Technology Data Exchange (ETDEWEB)

Silva Filho, Severino Higino da; Bieseki, Lindiane; Pergher, Sibele Berenice Castella, E-mail: sibelepergher@gmail.com [Universidade Federal do Rio Grande do Norte (LABPEMOL/UFRN), Natal, RN (Brazil). Lab. de Peneiras Moleculares; Maia, Ana Aurea B.; Angelica, Romulo Simoes [Universidade Federal do Para (UFPA), Belem PA (Brazil); Treichel, Helen [Universidade Federal da Fronteira Sil (UFFS), Erechim, RS (Brazil)

2017-05-15

The NaOH/metakaolin ratio and crystallization time were studied for the synthesis of zeolite NaA from a sample of kaolin from a Capim mine. The tests were carried out by using statistical design with axial points and replication of the central point. The samples obtained were characterized by X-ray diffraction (DRX), scanning electron microscopy and chemical analysis using a microprobe EPMA. The results showed that there is a relationship between the amount of NaOH added and crystallization time. The tests carried out using the lowest NaOH/metakaolin ratio (0.5) and the shortest time (4 h) produced a non-crystalline material. On the other hand, increasing the NaOH/metakaolin ratio and the crystallization time led to the formation of a NaA phase with a high structural level, but with the presence of a sodalite phase as an impurity. (author)

Application of 3D Electrical Resistivity Tomography As A Tool for Mapping Subsurface Cavities in a Kaolin Mining Site at Kankara in North Central Nigeria.

Science.gov (United States)

Eshimiakhe, D.; Jimoh, R.

2017-12-01

A Kaolin mining site at Dajin Gwanma in north central Nigeria was investigated to determine the possibility of using 3D ERT to detect subsurface voids created due to mining of kaolin deposit and to perhaps suggest areas prone to subsidence. This study was undertaken on conceptual resistivity model that subsurface voids characterized by higher or lower resistivity than the host, depending on weather the void is in-filled water or not. The data collection was carried out with Terrameter SAS 4000 and ES 464 electrode selector equipment. Dipole-dipole configuration at electrode spacing of 5m was used to acquire the data along parallel profiles laid at equal interval in the study area. While the acquired data along each profile were inverted with 2D algorithm, a script file was created to collate the 2D data set into a 3D format and subsequently inverted using 3D algorithm. A volumetric resistivity model block of the study area was also created using the voxler 4 software. The results show that the voids are characterized by high resistivity (950Ωm-2500Ωm) at depth of between 0-4m and low resistivity (10Ωm-100Ωm) at a depth of 5-30m indicating both air-filled and water-filled voids respectively. The study shows that the voids increase in dimension with depth in NW-SE direction, suggesting that the voids are trending most probably along vertical bedrock joints. It also suggest that voids may overtime grow large enough that the overlying top soil can no longer bridge it, leading to its collapse.

Effect of Compatibilizer on the Dynamic Mechanical and Electrical Properties of Kaolin Clay Reinforced EPDM Rubber

International Nuclear Information System (INIS)

Sarkhel, G.; Manjhi, S.

2013-01-01

Industrial pollution issue and dark colour of carbon black, clay based non black filler are getting more importance for reinforcing elastomer. EPDM-Kaolin composites with various maleated EPDM concentration have been prepared by mixing on a two roll mill. The rheometry data showed the optimum cure time increases with increasing compatibilizer concentration without decreasing torque value indicating that acidic functional groups comes from compatibilizer could retard cure rate and increase the optimum cure time rather than change in the ultimate cure state. As the filler concentration increases, the edge to edge and face to edge interaction between filler and EPDM increases and the free volume between EPDM molecules is reduced, the storage modulus increases. Moreover, the dynamic mechanical analysis also showed the increase in glass transition temperature with increase in filler concentration due to the inter-tubular diffusion of EPDM inside the clay. It was also observed that with increasing filler concentration, the resistivity and dielectric strength decreases and moreover with increasing compatibilizer concentration the resistivity decreases due to better dispersion of filler helps to build conduction path. The morphological study also revealed that homogeneity of filler dispersion increases with increase in compatibilizer concentration. (author)

Waste characterization emanated from kaolin submitted the improvement to process hydrocycloning; Caracterizacao do residuo provindo do beneficiamento do caulim submetido ao processo de hidrociclonagem

Energy Technology Data Exchange (ETDEWEB)

Barbosa Neto, M.C.; Nunes, A.S.; Caetano, A.L.A.; Marques, V.C.; Macedo, D.A.; Ferreira, H.S.; Dutra, R.P.S., E-mail: netobarbosa.2@gmail.com [Universidade Federal da Paraiba (UFPB), Joao Pessoa, PB (Brazil). Departamento de Engenharia de Materiais

2016-07-01

The hydrocyclones are equipment commonly used for separation of particles by size. The resulting material of this process usually presents different characteristics of the material, which was not subjected to treatment. Therefore, a study of the waste characteristics derived from kaolin processing submitted to hydrocycloning process compared to the same residue without going through the process was executed. The different samples were characterized by X-ray diffraction, X-ray fluorescence, particle size analysis and thermal analysis. The results indicate that the hydrocycloning not modify the mineralogical structure nor chemical material. The particle size analysis identified that the fine fraction, resulting from the process, presented particle size lower than the reference material. (author)

Preparation and characterization of ZnO microfiltration membrane and its support using kaolin (DD3 and CaCO3

Directory of Open Access Journals (Sweden)

B. Boudaira

Full Text Available Abstract The objective of the present paper was to prepare a ceramic support with membrane. Tubular ceramic supports prepared from kaolin (DD3 and calcium carbonate with 6 and 10 mm inner and outer diameters, respectively, were extruded and sintered at 1200 °C. It has been found that sintered supports had interesting characteristics: average pore size of about 5µm, porosity of about 50%, and monomodal pore size distribution. This support was used to be substrate for a membrane layer of microfiltration. This membrane layer was elaborated from zinc oxide, using slip casting technique. The specimens were subsequently sintered at 1000 °C. The microstructure and porosity as well as the permeability have also been studied. It has been found that the average pore size was about 1.2µm, the layer thickness was ~33µm, and the water permeability measured was about 880 L.h-1.m-2.bar-1.

Mineralogical characterization and beneficiation study of kaolin from Equador (RN) and Junco do Serido (PB) to increase the brightness index; Caracterizacao mineralogica e estudo do beneficiamento do caulim de Equador (RN) e Junco do Serido (PB) para elevacao do indice de alvura

Energy Technology Data Exchange (ETDEWEB)

Campos, V.M.J.S.; Bertolino, L.C., E-mail: vcampos@cetem.gov.br, E-mail: lcbertolino@cetem.gov.br [Centro de Tecnologia Minearal (CETEM), Rio de Janeiro, RJ (Brazil). Setor de Caracterizacao Tecnologica; Alves, O.C., E-mail: odivaldocambraia@id.uff.br [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Instituto de Quimica

2017-07-15

Kaolin is a rock composed mainly of kaolinite. It is used in many industrial segments, such as paper and ceramics. However, for these uses it is necessary to submit the ore to appropriate beneficiation, which generally involves magnetic separation and chemical bleaching, aiming to remove iron oxide and hydroxide, raising brightness index. This work reports the mineralogical characterization and analysis of the beneficiation of three samples of kaolin, two from Equador (Rio Grande do Norte - RN) and the third from Junco do Serido (Paraiba - PB). The samples were submitted to granulometric classification in sieve of 44 μm, magnetic separation in a magnetic induction of 14000 gauss, and chemical bleaching with sodium dithionite during 240 min. The processes were divided into two beneficiation routes. X-ray diffraction, chemical analysis by X-ray fluorescence and scanning electron microscopy were used for mineralogical characterization of the ore and measurement of the brightness index, while electron paramagnetic resonance was applied to study the variation of iron oxides and hydroxides during beneficiation. The results indicate that just 30 min of chemical bleaching without magnetic separation was sufficient to increase the brightness index from 78.2 to 90.2% and from 91.3 to 95.7% in the two samples from Equador (RN) and from 86.9 to 90.4% in the sample from Junco do Serido (PB). The magnetic separation, although causing a small increase in the brightness index, was inefficient for removal of iron oxides and hydroxides. The results indicated no need for using magnetic separation in plants for beneficiation of kaolin from these two locations, providing the reduction of production costs allowing better exploitation of the ore. (author)

Analysis and optimization of flocculation activity and turbidity reduction in kaolin suspension using pectin as a biopolymer flocculant.

Science.gov (United States)

Ho, Y C; Norli, I; Alkarkhi, Abbas F M; Morad, N

2009-01-01

The performance of pectin in turbidity reduction and the optimum condition were determined using Response Surface Methodology (RSM). The effect of pH, cation's concentration, and pectin's dosage on flocculating activity and turbidity reduction was investigated at three levels and optimized by using Box-Behnken Design (BBD). Coagulation and flocculation process were assessed with a standard jar test procedure with rapid and slow mixing of a kaolin suspension (aluminium silicate), at 150 rpm and 30 rpm, respectively, in which a cation e.g. Al(3+), acts as coagulant, and pectin acts as the flocculant. In this research, all factors exhibited significant effect on flocculating activity and turbidity reduction. The experimental data and model predictions well agreed. From the 3D response surface graph, maximum flocculating activity and turbidity reduction are in the region of pH greater than 3, cation concentration greater than 0.5 mM, and pectin dosage greater than 20 mg/L, using synthetic turbid wastewater within the range. The flocculating activity for pectin and turbidity reduction in wastewater is at 99%.

For production of ceramic plates coating using waste kaolin, granite and marble; Caracterizacao de residuos de caulim, granito e marmore para uso em massas ceramicas

Energy Technology Data Exchange (ETDEWEB)

Sales, J.L.; Morais, C.R.S.; Lima, L.M.R.; Altidis, M.E.D., E-mail: josyanne27@yahoo.com.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

2011-07-01

The objective is to benefit and characterize waste from kaolin, marble and granite studying their thermal properties and spectroscopic in employment perspective on ceramic production of flooring boards. The residues were benefited through the process of dry grinding mill in greyhounds and passed through sieve 0.074 mm (ABNT No. 200), observing their suitability for the formulation of ceramic pastes. Tests were performed physicochemical characterization (particle size analysis, X-ray fluorescence and X-ray diffraction) and thermal (differential thermal analysis and thermogravimetry). The results showed that these residues showed satisfactory properties for the purpose for which it proposes, and contribute to reducing environmental impacts, allowing the reuse of the production of ceramic plates (author)

Synthesis of Nano- alumina Powder from Impure Kaolin and its Application for Arsenite Removal from Aqueous Solutions

Directory of Open Access Journals (Sweden)

Ahmad Khodadadi Darban

2013-07-01

Full Text Available Adsorption is considered a cost-effective procedure, safer to handle with high removal efficiency. Activated alumina is the most commonly used adsorbent for the removal of arsenic from aqueous solutions. However, activated alumina has a low adsorption capacity and acts kinetically in a slow manner. An ideal adsorbent should have a high surface area, physical and/or chemical stability and be inexpensive. To meet this requirement, nanomeso porous γ-alumina with a high surface area (201.53 m2/g and small particle size (22–36 nm was prepared from inexpensive kaolin as the raw material, by precipitation method. The research results showed that adsorbent has the high adsorption capacity (for initial arsenite concentration up to 10 mg/L, in which 97.65% recovery was achieved. Optimal experimental conditions including pH, initial arsenite concentration and contact time were determined. Langmuir, Freundlich and Dubinin– Radushkevich isotherm models were applied to analyze the experimental data. The best interpretation for the experimental data was given by Langmuir adsorption isotherm equation and the maximum arsenite adsorbed by synthesized nano γ–alumina (qe was found to be 40 (mg/g.

Fabrication of recyclable and durable superhydrophobic materials with wear/corrosion-resistance properties from kaolin and polyvinylchloride

International Nuclear Information System (INIS)

Qu, Mengnan; Liu, Shanshan; He, Jinmei; Feng, Juan; Yao, Yali; Ma, Xuerui; Hou, Lingang; Liu, Xiangrong

2017-01-01

Highlights: • The scraped debris can be recycled and easily reused to fabricate the superhydrophobic materials. • The obtained materials displayed liquid-repellent toward water and several other liquids of daily life. • The superhydrophobic materials can retain excellent chemical stability and mechanical durability after rigorous tests. • This as-prepared material can be regarded as a real superhydrophobic “material”, not just the superhydrophobic “surface”. - Abstract: In this study, mechanically stable and recyclable superhydrophobic materials were prepared from polyvinylchloride (PVC) and kaolin nanoparticles modified by stearic acid using a simple and low-cost drop-coating. The obtained materials displayed liquid-repellent toward water and several other liquids of daily life (such as orange juice, coffee, milk, coca cola and ink). These superhydrophobic materials showed remarkable robustness against sandpaper abrasion, UV-irradiation and ultrasonication test, while retaining its superhydrophobicity even after 60 abrasion cycles loaded of 500 g with sandpaper, 7 days UV-irradiation or 120 min ultrasonication test. The excellent durability against complex conditions was attributed to the hierarchical structure and strong interfacial adhesion of the materials. More significantly, the materials used in the coating could be recycled and reconstructed without losing its superhydrophobicity. The current superhydrophobic materials tolerate rigorous environment, opening a new avenue to a variety of practical applications.

Fabrication of recyclable and durable superhydrophobic materials with wear/corrosion-resistance properties from kaolin and polyvinylchloride

Energy Technology Data Exchange (ETDEWEB)

Qu, Mengnan, E-mail: mnanqu@gmail.com; Liu, Shanshan; He, Jinmei, E-mail: jinmhe@gmail.com; Feng, Juan; Yao, Yali; Ma, Xuerui; Hou, Lingang; Liu, Xiangrong

2017-07-15

Highlights: • The scraped debris can be recycled and easily reused to fabricate the superhydrophobic materials. • The obtained materials displayed liquid-repellent toward water and several other liquids of daily life. • The superhydrophobic materials can retain excellent chemical stability and mechanical durability after rigorous tests. • This as-prepared material can be regarded as a real superhydrophobic “material”, not just the superhydrophobic “surface”. - Abstract: In this study, mechanically stable and recyclable superhydrophobic materials were prepared from polyvinylchloride (PVC) and kaolin nanoparticles modified by stearic acid using a simple and low-cost drop-coating. The obtained materials displayed liquid-repellent toward water and several other liquids of daily life (such as orange juice, coffee, milk, coca cola and ink). These superhydrophobic materials showed remarkable robustness against sandpaper abrasion, UV-irradiation and ultrasonication test, while retaining its superhydrophobicity even after 60 abrasion cycles loaded of 500 g with sandpaper, 7 days UV-irradiation or 120 min ultrasonication test. The excellent durability against complex conditions was attributed to the hierarchical structure and strong interfacial adhesion of the materials. More significantly, the materials used in the coating could be recycled and reconstructed without losing its superhydrophobicity. The current superhydrophobic materials tolerate rigorous environment, opening a new avenue to a variety of practical applications.

Investigating the Influence of the Cerium loading in prepared Y zeolite from Iraqi kaolin on its Catalytic Performance

Directory of Open Access Journals (Sweden)

Karim Khalifa Esgair

2018-01-01

Full Text Available In this study, the effects of different loading doses of cerium in the prepared NaY zeolite from Iraqi kaolin were investigated. Al-Duara refinery atmospheric residue fluid catalytic cracking was selected as palpation reaction for testing the catalytic activity of cerium loading NaY zeolite. The insertion of cerium in NaY zeolites has been synthesized by simple ion exchange methods. Three samples of modified zeolite Y have been obtained by replacing the sodium ions in the original sample with cerium and the weight percent added are 0.35, 0.64, and 1.06 respectively. The effects of cerium loading to zeolite Y in different weight percent on the cracking catalysts were studied by employing a laboratory fluidized bed reactor. The experiments have been performed with weight hourly space velocity (WHSV range from 6 to 24 h-1, and the temperature range from 450 to 510 oC. The activity of the catalyst with 1.06 wt% cerium has been shown to be much greater than that of the sample parent NaY. Also it was observed that the addition of the cerium causes an increase in the thermal stability of the zeolite.

Smart Natural Fiber Reinforced Plastic (NFRP) Composites Based On Recycled Polypropylene in The Presence Kaolin

Science.gov (United States)

Suharty, N. S.; Ismail, H.; Diharjo, K.; Handayani, D. S.; Lestari, W. A.

2017-07-01

Composites contain double filler material which act as reinforcement and flame retardants of recycled polypropylene (rPP)/kaolin(Kao)/palm oil empty bunch fiber (PEBF) have been succesfully prepared. The composites were synthesized through reactively solution method, using coupling agent PP-g-AA and compatibilizer DVB. The effect of double filler [Kao/PEBF] were investigated flexural strength (FS), inflammability, and morphology. Mechanical testing result in accordance to ASTM D790, the FS of rPP/DVB/PP-g-AA/Kao+ZB/PEBF composite was 48% higher than that of rPP matrix. Moreover, flexural modulus (FM) was significantly improved by 56% as compared to that of rPP matrix. The scanning electron images (SEM) shown good dispersion of [Ka/PEBF] and good filler-matrix interaction. The inflammability testing result which is tested using ASTM D635, showed that the flame resistance of rPP/DVB/PP-g-AA/Kao+ZB/PEBF composite was improve by increasing of time to ignition (TTI) about 857% and burning rate (BR) decreasing to 66% compared to the raw material rPP matrix. In the same time, the addition of 20% (w/w) PEBF as a second filler to form rPP/DVB/PP-g-AA/Kao+ZB/PEBF composites (F5) is able to increase: the FS by 17.5%, the FM by 19%, the TTI by 7.6% and the BR by 3.7% compared to the composite without PEBF (F2).

Characterization and Evaluation of a kaolin deposit located in Los Azufres Michoacan, Mexico, for Industrial Use

International Nuclear Information System (INIS)

Guillen, J.; Bribiesca, S.; Escudero, R.

2012-01-01

In this work a kaolin ore from the region of Los Azufres, state of Michoacan, Mexico, was characterized and evaluated in order to assess its use in the industry. A powder fraction less than 45 μm were studied by X-ray fluorescence (XRF), x-ray diffraction (XRD) and infrared spectroscopy (IR). The results showed high silica content of ∼70%, associated with minerals such as cristobalite, tridimite and quartz followed by kaolinite and a small amount of alunite. The distribution, morphology and surface area of the particles were obtained by Laser Diffraction, Scanning Electron Microscopy (SEM) and Brunauer Emmett Teller technique (BET). Thermal characterization was performed by differential thermal analysis (DTA), thermal gravimetric analysis (TGA) and dilatometric analysis. The thermal characterization results displayed a strong mineral thermal expansion from room temperature to 300 degree centigrade, followed by an abrupt contraction a temperatures between 580 degree centigrade to 920 degree. This could be associated with phase transformations of the polymorph of silica, the dehydroxylation of the alunite and kaolinite and the desulfatation of alunite. The physical properties such as mineral color, degree of whiteness, plasticity, linear shrinkage and density were also determined. Finally whit the results obtained in this work, it can be concluded that the investigated ore is highly recommended for the cement industry and plastic. (Author) 29 refs.

Synthesis of mullite (3Al2O32SiO2) from local kaolin for radiation shielding

Science.gov (United States)

Ripin, Azuhar; Mohamed, Faizal; Aman, Asyraf

2018-04-01

Raw kaolin from Kota Tinggi, Johor was used in this study to produce ceramic mullite (3Al2O22SiO2) for radiation shielding materials. In this work, an attempt was made to study the potential of local minerals to be used as a shielding barrier for diagnostic radiology radiation facilities in hospitals and medical centers throughout Malaysia. The conventional ceramic processing route was employed in the study using different pressing strength and sintering time. The obtained samples were characterized using X-ray diffractometer (XRD) for phase identification of each of the samples. The lead equivalent (LE) test was carried out using 15.05 mCi Cobalt-57 with gamma energy of 122 keV to compute the abilities of the mullite ceramic samples to attenuate the radiation. XRD patterns of prepared ceramics revealed the presence of orthorhombic mullite, hexagonal quartz and orthorhombic sillimanite structures. Furthermore, the radiation test displayed the ability of ceramics to shield of 70 % of gamma radiation at the distance of 60 cm from the radiation source. The highest lead equivalent thickness is 1.0 mm Pb and the lowest is about 0.06 mm Pb. From the result, it is shown that the ceramic has the potential to use as a shielding barrier in diagnostic radiology facilities due to the ability of reducing the radiation dose up to 70 % from its initial value.

Coagulation performance of a novel poly-ferric-acetate (PFC) coagulant in phosphate-kaolin synthetic water treatment

Energy Technology Data Exchange (ETDEWEB)

Wei, Yanxin; Lu, Jinpeng; Dong, Xiongzi; Yao, Chengli [Hefei Normal University, Hefei (China); Hao, Jianwen [Anhui Vocational and Technical College, Hefei (China)

2017-10-15

The process of coagulation-flocculation is increasingly applied in wastewater treatment. And the polymerized inorganic coagulants are widely used among these coagulation-flocculation processes. However, conventional coagulants using sulfates or chlorides as counter anion may give rise to corrosion. The purpose of this study was to synthesize PFC coagulants in which acetate is used as counter anion. The influences on the preparation of PFC were optimized. The synthesis was done at the optimum conditions, such as temperature of 60 .deg. C, the Fe/CH{sub 3}COOH molar ratio of 1 : 4.0 and reaction time of 6 h, respectively. The prepared PFC coagulants were characterized by Fourier transform infrared (FTIR) spectrophotometry and scanning electron microscopy (SEM). PFC was found to mainly form complexation polymeric species and present more cluster and lamellar structure. A series of jar tests were carried out to study the coagulation performance of PFC and PFS in phosphate-kaolin synthetic water treatment. Results showed that the coagulation performance of PFC was more efficient than PFS's in terms of the phosphorus removal efficiency and the residual turbidity. Due to using acetate as counter anion to iron, PFC is less harmful to the processes of water treatment and equipment than that of the conventional coagulants applied chlorides or sulfates. Therefore, PFC is a promising coagulant in the process of corrosion sensitive applications and the process of wastewater containing phosphorus treatment.

Applicability of alkali activated slag-seeded Egyptian Sinai kaolin for the immobilization of 60Co radionuclide

International Nuclear Information System (INIS)

El-Naggar, M.R.

2014-01-01

The present work was established to determine the applicability of local Egyptian kaolinite and blast furnace slag (BFS) as raw materials toward the synthesis of geopolymers and subsequent immobilization of cobalt-60, which is one of the most abundant radionuclides generated in radioactive waste streams in Egypt. XRF, XRD, FT-IR, and SEM techniques were used to characterize the local raw materials and their corresponding alkali activated products. Metakaolin (MK) was obtained by thermal treatment of Egyptian Sinai kaolin 750 °C/4 h. MK and five different BFS content (5, 10, 30, 50 and 80%) were used to synthesize geopolymeric matrices using an alkaline activator of Si-modulus = 1.35 at solid/liquid ratios of 0.8. Compressive strength tests were performed indicating that 50% BFS addition gave the highest values of compressive strength. The IAEA standard leaching tests of cobalt-60 from the solidified waste matrices were carried out. The effective diffusion coefficients of cobalt-60 radionuclides from the solidified waste matrices were calculated to be in the order of 10 −14 cm 2 /s. Leaching of radionuclides was examined to be controlled by the wash-off mechanism with very acceptable values. These results gave encouragement that the tested Egyptian raw materials can be conveniently applied for the synthesis of geopolymers that can be used as a low-cost and high-efficiency materials for the immobilization of radioactive waste

Cordierite obtaining by reactive sintering of kaolin, tal and transition alumina; Obtencao de ceramicas a base de mulita-cordieta via sinterizacao reativa de caulim, talco e alumina

Energy Technology Data Exchange (ETDEWEB)

Almeida Filho, Humberto Dias de; Sales, Lindemberg Felismino; Goncalves, Joao de Freitas; Macedo, Daniel Araujo de [Universidade Federal da Paraiba (UFPB), Joao Pessoa, PB (Brazil). Departamento de Engenharia de Materiais

2016-07-01

Cordierite and mullite are important applications in the manufacture of ceramic products with high resistance to thermal shock. The present work aimed to obtaining ceramics based on cordierite (2MgO.2Al2O3.5SiO2) and mullite (3Al2O3.2SiO2) via reactive sintering of one formulation containing kaolin ceramics, talc and alumina. Uniaxially pressed tablet to 125 MPa were sintered between 1100 and 1400 ° C for 1 h. The sintering temperature effect in the phase composition was evaluated by X-ray diffraction. The morphological characterization was performed by scanning electron microscopy. Samples sintered at 1300 ° C had 10 wt% of spinel (MgAl2O4) as secondary and apparent phase density 2.56 g / cm3. (author)

Effect of kaolin silver complex on the control of populations of Brettanomyces and acetic acid bacteria in wine.

Science.gov (United States)

Izquierdo-Cañas, P M; López-Martín, R; García-Romero, E; González-Arenzana, L; Mínguez-Sanz, S; Chatonnet, P; Palacios-García, A; Puig-Pujol, A

2018-05-01

In this work, the effects of kaolin silver complex (KAgC) have been evaluated to replace the use of SO 2 for the control of spoilage microorganisms in the winemaking process. The results showed that KAgC at a dose of 1 g/L provided effective control against the development of B. bruxellensis and acetic acid bacteria. In wines artificially contaminated with an initial population of B. bruxellensis at 10 4 CFU/mL, a concentration proven to produce off flavors in wine, only residual populations of the contaminating yeast remained after 24 days of contact with the additive. Populations of acetic bacteria inoculated into wine at concentrations of 10 2 and 10 4  CFU/mL were reduced to negligible levels after 72 h of treatment with KAgC. The antimicrobial effect of KAgC against B. bruxellensis and acetic bacteria was also demonstrated in a wine naturally contaminated by these microorganisms, decreasing their population in a similar way to a chitosan treatment. Related to this effect, wines with KAgC showed lower concentrations of acetic acid and 4-ethyl phenol than wines without KAgC. The silver concentration from KAgC that remained in the finished wines was below the legal limits. These results demonstrated the effectiveness of KAgC to reduce spoilage microorganisms in winemaking.

8559 Volume 14 No. 1 March 2014 Short communication THE ...

African Journals Online (AJOL)

owe

2014-03-01

Mar 1, 2014 ... diets were used comprising 0g kaolin/kg feed, 10g kaolin/kg, 20g kaolin/kg ... Kaolin or China clay is one of such non-conventional feed additives. ... Records taken include daily feed intake, weekly body measurements, cost of.

Physicochemical properties of cross-linked poly-gamma-glutamic acid and its flocculating activity against kaolin suspension

International Nuclear Information System (INIS)

Taniguchi, M.; Kato, K.; Shimauchi, A.; Ping, X.; Fujita, K.; Tanaka, T.; Tarui, Y.; Hirasawa, E.

2005-01-01

Cross-linked poly-Gamma-glutamic acid (C-L Gamma-PGA) was prepared with Gamma-PGA irradiated with Gamma-PGA at various kGy values. The physicochemical properties including viscosity and water absorption capacity were compared between C-L Gamma-PGA and several typical flocculating agents. The viscosity of C-L Gamma-PGA increased with the dose of Gamma-lrradiatio, although the water absorption capacity of C-L Gamma-PGA did not, which showed a maximum of 1005.6 ml/g at 20 kGy. Flocculating activity against kaolin suspension was not observed for any of the test compounds when used singly. However, the activity of C-L Gamma-PGA markedly increased following the addition of polyaluminum chloride. The activity increased with temperature up to 80deg C and remained at 80 deg C of heat pretreatment for 1 h, but did not at more than 50 deg C of beat pretreatment for 24 h. The activity was also observed within a pH range of 4.5-10.0. Roth the water absorption capacity and flocculating activity of C-L Gamma-PGA decreased in parallel with increasing NaCl concentration, suggesting that the hocculating activity of C-L Gamma-PGA was associated with its water absorption capacity, rather than viscosity. An investigation of the effects of various cations on the flocculating activity of C-L Gamma-PGA showed that only trivalent catlons had a synergistic effect. The mechanism of C-L Gamma-PGA flocculating activity is discussed based on the results of preliminary experiments

Incorporation of waste and fiber kaolin caroa panels in Medium Density Fiberboard - MDF; Incorporacao de residuos de caulim e fibras de caroa em paineis de media densidade- MDF

Energy Technology Data Exchange (ETDEWEB)

Bezerra, A.F.C.; Santana, L.N.L.; Neves, G.A.; Carvalho, L.H. de; Lopes, F.F.M., E-mail: anaflavia.dema@yahoo.com.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

2012-07-01

Medium-density panels are composites molded under high temperature and pressure which have physical and mechanical properties similar to those of solid wood. Their composition includes eucalyptus grandis fibers and pinus elliotii fibers, but other fibers can be used such as caroa fibers. The goal of this work was to manufacture panels which kaolin waste and caroa fibers and compare their physical, chemical and mechanical of these panels with a others. Both residue and the fibers were characterized by: differential thermal analysis, thermal gravimetric analysis and Xray diffraction. Through the process of pressing the test specimens were fabricated, test samples were evaluated by three point bending, internal bond, water absorption and swelling in thickness. The samples have low levels of thickness swelling, flexural strength and higher tensile and absorption content relative to commercial MDF. (author)

Potencialidades de um caulim calcinado como material de substituição parcial do cimento portland em argamassas Potentialities of a calcined kaolin as material of partial replacement of portland cement in mortars

Directory of Open Access Journals (Sweden)

Marilia P. de Oliveira

2006-06-01

Full Text Available A utilização de argilas calcinadas na forma de metacaulinita, como material pozolânico para argamassas e concretos, tem recebido atenção considerável nos últimos anos. Este trabalho objetivou avaliar o desempenho mecânico de argamassas, nas quais foi utilizado um caulim calcinado proveniente do Estado da Paraíba, como material de substituição parcial do cimento Portland. Utilizaram-se duas finuras do caulim: passando nas peneiras ABNT 200 (0,074 mm e 325 (0,044 mm e calcinados nas temperaturas de 700, 800 e 900 ºC pelo tempo de 2 h. As amostras foram caracterizadas através de análise química, análise térmica diferencial, difração de raios-X e área específica. Obteve-se o índice de atividade pozolânica com a cal e o cimento Portland. O percentual de substituição adotado foi de 0, 10, 20, 30 e 40%. A relação aglomerante: areia foi de 1:1,5 e a relação água/aglomerante fixada igual 0,4. O efeito da substituição parcial do cimento na argamassa foi avaliado através da resistência à compressão simples, nas idades de 7, 28 e 90 dias. As argamassas estudadas apresentaram resistência superior em relação à da referência, até o nível de 30% de substituição.The use of burnt clays, in the metakaolin form, as pozzolanic material for mortars and concretes has received a remarkable attention in the last years. This paper aimed to evaluate the mechanical property of mortars, in which a calcined kaolin originating from the State of Paraiba, was used as partial cement replacement material. Two finess of the kaolin were used: ABNT 200 (0.074 mm and 325 (0.044 mm and burnt at temperatures of 700, 800 and 900 ºC for a period of 2 h. Both materials were characterized by chemical analysis, differential thermal analysis, X-ray diffraction, specific area tests. The pozolanic activity index was obtanied using lime and cement Portland. The amounts of replacement were 10, 20, 30 and 40%, besides the reference mortar. The binder

Preparação e caracterização de materiais compósitos SiC/caulim/Al via "squeeze-casting" Preparation and characterization of SiC/kaolin/Al composite materials by squeeze- casting

Directory of Open Access Journals (Sweden)

M. Freitas

2009-09-01

manufacturing these composites is the process of metal casting infiltration under pressure called squeeze-casting. This process offers some advantages, such as ease of producing the composite, low cost and ability to form network structures. In this work were produced and characterized Al-SiC composites, with concentrations in kaolin ranging between 10 and 50% in place to SiC majority phase. The ceramic pre-forms were produced to controlling the fraction of the size SiC/kaolin for better infiltration. These pre-forms after sintering at 1100 ºC/1 h resulted highly porous, and the porosity increased with the increase of kaolin in place to SiC particles. XRD analysis showed the existence of quartz particles beyond the SiC phase. During the infiltration and heat treatment process, the liquid aluminum reacted preferably with quartz and other aluminosilicates particles of the pre-form reducing them, precipitating alumina and silicon in the microstructure, which also presented aluminum in excess that not reacted in the process. The silica and silicates of pre-form, reacted preferably with the aluminum, preventing the formation of Al4C3 phase, which is highly hygroscopic and causes the composite degradation. Depending on the composition, the SiC - kaolin - Al composite developed in this work, can be used in applications involving high bending mechanical resistance (240 to 300 MPa, low density and hardness surface between 180 and 380 kgf/mm².

Influência da adição de resíduo de caulim nas propriedades tecnológicas de uma massa padrão de porcelanato produzido em escala industrial Influence of kaolin waste addition on technological properties of a standard stoneware formulation produced in industrial scale

Directory of Open Access Journals (Sweden)

M. L. Varela

2009-06-01

Full Text Available Atualmente existe uma grande preocupação por parte das indústrias com a disposição dos resíduos gerados ao longo do processo produtivo. No setor mineral não é diferente, pois este gera grande volume de resíduos. Verificou-se que a indústria de beneficiamento do caulim descarta grandes volumes de resíduo constituído basicamente de caulinita, mica muscovita e quartzo, ocasionando um impacto ambiental, o que tem justificado os esforços de pesquisas para sua solução. Deste modo, foi estudado o efeito da incorporação de um resíduo proveniente do beneficiamento de caulim sobre as propriedades físicas e tecnológicas de revestimentos cerâmicos de alta qualidade. O objetivo é caracterizar e estudar o processamento do resíduo proveniente da indústria de beneficiamento do caulim com adição de uma "massa padrão", fornecida por uma indústria de revestimento cerâmico. O resíduo foi caracterizado por meio de análises de difração de raios X, fluorescência de raios X e determinação do tamanho de partículas. Foram realizados ensaios de absorção de água, porosidade aparente, retração linear após queima, massa específica aparente e tensão de ruptura à flexão, para determinação das propriedades tecnológicas destes materiais. Os resultados mostram que o resíduo estudado pode ser considerado como matéria-prima de grande potencial para a indústria de pisos e revestimentos cerâmicos.There is a great concern by the industrial area on the disposal of waste generated during the production process. In the mineral sector the situation is the same, because large volumes of waste are disposed. The kaolin processing industry generates waste consisting mainly of kaolinite, mica and quartz muscovite, causing an environmental impact, justifying the research efforts to find a solution for this problem. The effect of the waste from the kaolin processing incorporation on the technological and physical properties of high quality

Analysis of influence of the inclusion of residue of kaolin on the properties and on the variation of major oxides present in clay city Bento Fernandes (RN)

International Nuclear Information System (INIS)

Silva, Hugo Fernandes Medeiros de; Lima, Cassiano dos Santos; Silva, Gilson Garcia da; Machado, Tercio Graciano; Albuquerque, Rosanne Azevedo de; Gomes, Uilame Umbelino

2011-01-01

Research Foundation for Support of Education and Technological Development of Rio Grande do Norte - FUNCERN found that 38% of deposits visited in RN products sold in other states, 20% did not sell tiles RN, 8% preferred the tiles outside. All to supply a market segment demanding and are looking for differentiated products, which require manufacturers of certified quality products contributing to the quality process in the construction industry. It is known that the ceramic bodies are manufactured from the composition of two or more materials with different characteristics in their composition. Thus, one of the key steps is the dosage of raw materials and additives. This device allows to target the many wastes from industry. This paper aims to study the physical and mechanical properties of ceramic body resulting from the inclusion of residual kaolin clay on the city of Bento Fernandes (RN), analyzing the influence of variation of major oxides present in the raw material on the behavior of the final product. (author)

Dispersion de phyllosilicates et processus de frittage de céramiques silicatées

OpenAIRE

Houta , Nadia

2015-01-01

This thesis is devoted to improve both densification and stress to rupture values of silicate ceramics mainly elaborated from kaolin. This improvement is achieved by replacing a proportion of kaolin by halloysite. Indeed, this way also allows to highlight the influence of the shape of particles and their organization on microstructural properties. First, the dispersion of suspensions containing only kaolin or a mixture of kaolin and halloysite was optimized by reducing the size of agglomerate...

Fourier transform infrared spectrophotometry and X-ray powder ...

African Journals Online (AJOL)

This study aimed at demonstrating complementary roles offered by both Fourier transform infrared (FTIR) spectrophotometry and x-ray powder diffraction (XRPD) techniques in characterizing clay size fraction of kaolins. The clay size fraction of kaolin samples obtained from Kgwakgwe, Makoro, Lobatse and Serule kaolin ...

Properties of Portland-Composite Cements with metakaolin: Commercial and manufactured by Thermal Activation of Serbian Kaolin Clay

Directory of Open Access Journals (Sweden)

Mitrovic A.

2012-09-01

Full Text Available Portland-composite cements (CEM II were prepared with addition of 5 to 35% of metakaolin (MK, manufactured by thermal activation/calcination of Serbian kaolin clay, and commercial matakaolin (CMK. Performance of the composite cements was evaluated, through the setting time (initial and final, compressive strengths (for ages 2, 7, 28, 90 and 180 days and soundness, and compared with control cement (Portland cement – CEM I. Setting time (initial and final is accelerated in Portlandcomposite cements, for both metakaolins used. The acceleration is higher in cement with addition of commercial metakaolin. Lower compressive strength is obtained after 2 days of curing for all Portland-composite cements in comparison with control cement, since pozzolanic reaction still did not show its effect. After 7 days, pozzolanic reaction show its effect, manifested as compressive strength increase of Portland-composite cements with addition of up to 35% of CMK, and 25% in the case of cements with MK. After 28 days compressive strength was higher than that for control cement for cements prepared with addition of CMK, and with addition of up to 25% MK. After 90 days increased compressive strength was noticed with addition of 10 - 20% of CMK, and with 10 and 15% of MK, while after 180 days addition of both metakaolins influences compressive strength decrease. The results of the soundness, 0.5 mm for CEM I, and 1.0 mm in most Portland-composite cements indicate soundness increase with addition of metakaolins. Generally, better performance of Portland-composite cements was obtained with addition of commercial metakaolin, which may be attributed to the differences in the pozzolanic activity of the applied metakaolins, 20.5 MPa and 14.9 MPa for CMK and MK, respectively. By our previous findings pozzolanic activity of the thermally activated clay may be increased by subsequent milling of the metakaolin manufactured by thermal activation process.

Análise da co-utilização do resíduo do beneficiamento do caulim e serragem de granito para produção de blocos e telhas cerâmicos Analysis of the use of kaolin processing waste and granite sawing waste together for the production of ceramic bricks and roof tiles

Directory of Open Access Journals (Sweden)

R. R. Menezes

2007-06-01

Full Text Available O volume de resíduos gerado pela mineração e o beneficiamento mineral vêm se intensificando a cada dia, em virtude do aumento da demanda causado pelo crescimento da economia mundial. As indústrias do beneficiamento do caulim e da serragem do granito são importantes segmentos econômicos do Estado da Paraíba, entretanto produzem enormes quantidades de resíduos. Assim, este trabalho tem por objetivo caracterizar os resíduos do beneficiamento do caulim e da serragem do granito e avaliar a viabilidade de sua co-utilização para produção de blocos e telhas cerâmicos. Os resíduos foram caracterizados através da determinação de sua composição química e mineralógica, pelo uso de difração de raios X e análise térmica diferencial e gravimétrica, distribuição e tamanho de partículas e análise morfológica por microscopia eletrônica de varredura. Foram formuladas composições contendo os resíduos e confeccionados corpos de prova por extrusão. Os corpos de prova foram queimados e em seguida determinou-se sua absorção de água e módulo de ruptura à flexão. Pode-se observar que o resíduo do caulim é constituído por caulinita, mica e quartzo, que o resíduo de granito é constituído por quartzo, mica, albita e calcita e, que os resíduos apresentam distribuições granulométricas significativamente diferentes. Concluiu-se também que é possível a incorporação de até 50% de resíduo em formulações para produção de blocos e telhas cerâmicas e que a co-utilização do resíduo de granito e de caulim possibilita obter propriedades físicas superiores às observadas nos corpos de prova com incorporação de apenas resíduo de caulim.The amount of wastes generated by the miner and mineral processing industries has increasing day by day due to the high demand cause by the global economy grow up. The processing kaolin ad sawing granite industries are important economic segments in the state of Paraíba, but generate

Expansão por umidade de revestimentos cerâmicos incorporados com residuos de granito e caulim Moisture expansion of ceramic tiles produced using kaolin and granite wastes

Directory of Open Access Journals (Sweden)

A. M. G. D. Mendonça

2012-06-01

Full Text Available Expansão por umidade (EPU é o aumento das dimensões dos materiais cerâmicos em virtude da adsorção de água. A EPU geralmente ocorre lentamente e é relativamente pequena, mas, mesmo assim, pode comprometer a aderência das placas cerâmicas ao contrapiso, levar ao gretamento do vidrado e conduzir ao aparecimento de trincas em tijolos. Neste trabalho empregaram-se massas incorporadas com resíduos de caulim e de granito objetivando estudar a EPU de revestimentos cerâmicos. As matérias-primas foram beneficiadas e submetidas às caracterizações físicas e mineralógicas através de ensaios de análise granulométrica por difração a laser, análise química, análise termodiferencial, termogravimétrica e difração de raios X. Os resultados mostraram que os resíduos de caulim e de granito podem ser utilizados como matéria-prima cerâmica alternativa, pois apresentam características similares às matérias-primas cerâmicas convencionais, permitindo a obtenção de peças com resultados de EPU satisfatórios quando comparado ao valor limite de 0,6 mm/m (0,06% proposto pela ABNT para revestimentos cerâmicos, notadamente em composições com teores de até 20% de resíduos, a temperaturas superiores a 1000 ºC.Moisture expansion (ME is the term used to describe the expansion of ceramic materials due to the adsorption of water. ME usually occurs slowly and is relatively small, but, it can damage the ceramic tiles adhesion to the underlayment, craze the glaze and lead to the development of cracks on ceramics bricks. In this work kaolin and granite wastes were incorporated in ceramic compositions aiming study their influence on the ME of ceramic tiles. Raw materials were processed and submitted to characterization: physical and mineralogical by laser diffraction particle size analysis, chemical analysis, thermodifferential and thermogravimetric analysis and X-ray diffraction. Results showed that kaolin and granite wastes can be

Rational Practices to Manage Boll Weevils Colonization and Population Growth on Family Farms in the Semiárido Region of Brazil.

Science.gov (United States)

Neves, Robério C S; Colares, Felipe; Torres, Jorge B; Santos, Roberta L; Bastos, Cristina S

2014-10-31

Because boll weevil, Anthonomus grandis Boh. develops partially protected inside cotton fruiting structures, once they become established in a field, they are difficult to control, even with nearly continuous insecticide spray. During two cotton-growing seasons in the Semiárido region of Pernambuco State, Brazil, we tested the use of kaolin sprays to disrupt plant colonization through visual cue interference, combined with removal of fallen fruiting bodies to restrain boll weevil population growth after colonization. Kaolin spray under non-choice trials resulted in 2.2×, 4.4×, and 8.6× fewer weevils, oviposition and feeding punctures on kaolin-treated plants, respectively, despite demonstrating no statistical differences for colonization and population growth. Early season sprays in 2010 occurred during a period of rainfall, and hence, under our fixed spraying schedule no significant differences in boll weevil colonization were detected. In 2011, when kaolin sprays were not washed out by rain, delayed boll weevil colonization and reduction on attacked fruiting bodies were observed in eight out of 12 evaluations, and kaolin-treated plots had 2.7× fewer damaged fruiting bodies compared to untreated plots. Adoption of simple measures such as removal of fallen fruiting bodies and prompt reapplication of kaolin sprays after rainfall show promise in reducing boll weevil infestation.

Rational Practices to Manage Boll Weevils Colonization and Population Growth on Family Farms in the Semiárido Region of Brazil

Directory of Open Access Journals (Sweden)

Robério C. S. Neves

2014-10-01

Full Text Available Because boll weevil, Anthonomus grandis Boh. develops partially protected inside cotton fruiting structures, once they become established in a field, they are difficult to control, even with nearly continuous insecticide spray. During two cotton-growing seasons in the Semiárido region of Pernambuco State, Brazil, we tested the use of kaolin sprays to disrupt plant colonization through visual cue interference, combined with removal of fallen fruiting bodies to restrain boll weevil population growth after colonization. Kaolin spray under non-choice trials resulted in 2.2×, 4.4×, and 8.6× fewer weevils, oviposition and feeding punctures on kaolin-treated plants, respectively, despite demonstrating no statistical differences for colonization and population growth. Early season sprays in 2010 occurred during a period of rainfall, and hence, under our fixed spraying schedule no significant differences in boll weevil colonization were detected. In 2011, when kaolin sprays were not washed out by rain, delayed boll weevil colonization and reduction on attacked fruiting bodies were observed in eight out of 12 evaluations, and kaolin-treated plots had 2.7× fewer damaged fruiting bodies compared to untreated plots. Adoption of simple measures such as removal of fallen fruiting bodies and prompt reapplication of kaolin sprays after rainfall show promise in reducing boll weevil infestation.

Behavioral and electroantennogram responses of plum curculio, Conotrachelus nenuphar, to selected noxious plant extracts and insecticides.

Science.gov (United States)

Gӧkçe, A; Stelinski, L L; Nortman, D R; Bryan, W W; Whalon, M E

2014-01-01

Behavioral and electroantennogram responses of plum curculio, Conotrachelus nenuphar (Herbst) (Coleoptera: Curculionidae), adults were tested for several methanolic plant extracts and organically approved insecticides. Plant extracts were evaluated for their potential as antifeedants or oviposition deterrents. These extract responses were also compared to those elicited by the non-neurotoxic, organic irritant-insecticide kaolin clay. Both sexes of plum curculio exhibited antennal response as measured by electroantennogram, which ranged from 0.2 to 1.1 mV, to plant extracts and the organic irritant/insecticide, with the greatest response to the extract of rough cocklebur, Xanthium strumarium L. (1.1 mV). No choice tests were conducted to compare feeding and oviposition by plum curculio on untreated apples or on apples treated with one of the extracts or the insecticide. The insecticide pyrethrum and extracts of X. strumarium and greater burdock, Arctium lappa L., significantly reduced feeding. Also, pyrethrum, A. lappa, Humulus lupulus L. (common hop), X. strumarium, and Verbascum songaricum Schrenk extracts completely inhibited egg deposition. In no-choice assays, the effects of kaolin clay with incorporated plant extracts on plum curculio feeding and oviposition were monitored as complementary tests. A. lappa-kaolin, H. lupulus-kaolin, and X. strumarium-kaolin mixtures significantly reduced the feeding of plum curculio compared to the control or kaolin clay alone. Each of the plant extract-kaolin mixtures evaluated, with the exception of Bifora radians Bieberstein (wild bishop), completely inhibited plum curculio oviposition as compared to controls. This is an open access paper. We use the Creative Commons Attribution 3.0 license that permits unrestricted use, provided that the paper is properly attributed.

Computer simulation of mobilization and mixing of kaolin with submerged liquid jets in 25,000-gallon horizontal cylindrical tanks

International Nuclear Information System (INIS)

Eyler, L.L.; Mahoney, L.A.

1995-03-01

This report presents and analyzes results of computer model simulation of mobilization and mixing of kaolin using the TEMPEST code. The simulations are conducted in a horizontal cylindrical geometry replicating a 95 m 3 (25,000 gal) test tank at ORNL, which is scaled to approximate Melton Valley Storage tanks, which are 190 m 3 (50,000 gal). Mobilization and mixing is accomplished by two submerged liquid jets. Two configurations are simulated, one with the jets located at the center of the tank lengthwise and one with the jets located 1/4 tank length from one end. Computer simulations of both jet and suction configurations are performed. Total flow rates of 50, 100, and 200 gpm are modeled, corresponding to jet velocities of 1.52, 3.05, 6.10 m/s (5, 10, 20 ft/s). Calculations were performed to a time of 2 h for the center jet location and to a little over 1 h for the quarter jet location. This report presents computer and fluid properties model basis, preliminary numerical testing, and results. The results are presented in form of flow field and sludge layer contours. Degree of mobilization is presented as fraction of initial sludge layer remaining as a function of time. For the center jet location at 200 gpm, the sludge layer is completely mobilized in just over 1 h. For 100 gpm flow, about 5% of the sludge layer remains after 2 h. For 50 gpm flow, nearly 40% of the initial sludge layer remains after 2 h. For the quarter jets at 200 gpm, about 10% of the initial sludge layer remains after 1 h. For 100 gpm, about 40% of the sludge layer remains after 1 h. The boundary of the sludge layer is defined as 98% max packing for the particles. Mixing time estimates for these cases range from between 9.4 h and 16.2 h. A more critical evaluation and comparison of predictions and the test results is needed

A kinetic study of gaseous potassium capture by coal minerals in a high temperature fixed-bed reactor

DEFF Research Database (Denmark)

Zheng, Yuanjing; Jensen, Peter Arendt; Jensen, Anker Degn

2008-01-01

The reactions between gaseous potassium chloride and coal minerals were investigated in a lab-scale high temperature fixed-bed reactor using single sorbent pellets. The applied coal minerals included kaolin, mullite, silica, alumina, bituminous coal ash, and lignite coal ash that were formed...... into long cylindrical pellets. Kaolin and bituminous coal ash that both have significant amounts of Si and Al show superior potassium capture characteristics. Experimental results show that capture of potassium by kaolin is independent of the gas oxygen content. Kaolin releases water and forms metakaolin...... when heated at temperatures above 450°C. The amounts of potassium captured by metakaolin pellet decreases with increasing reaction temperature in the range of 900-1300°C and increases again with further increasing the temperature up to 1500°C. There is no reaction of pre-made mullite with KCl...

Defluorination of drinking water using surfactant modified zeolites ...

African Journals Online (AJOL)

This study focused on the removal of fluoridefrom groundwater by employing surfactant modified zeolites (SMZ) synthesized using locallyavailable kaolin material as precursor. The zeolite synthesis involved calcination of kaolin, alkaline fusion and hydrothermal treatment. The final product was modified with 5g/L ...

75 FR 13717 - Endangered and Threatened Wildlife and Plants; 90-Day Finding on a Petition to List the Southern...

Science.gov (United States)

2010-03-23

...-12) attributed to sedimentation, channelization, impoundment, sand and gravel mining, and chemical..., and/or sedimentation from headwater kaolin mines (Hartfield and Jones 1990, pp. 22-24). The kaolin mines that were the suspected source of sedimentation in the Buttahatchee have since been stabilized...

Síntese e caracterização de hidrogéis compósitos a partir de copolímeros acrilamida-acrilato e caulim: efeito da constituição de diferentes caulins do nordeste brasileiro

Directory of Open Access Journals (Sweden)

Carlos W. de Q. Brito

2013-01-01

Full Text Available Superabsorbent hydrogels based on poly (acrylamide-co-acrylate and different kaolins, were prepared by free-radical aqueous copolymerization. FTIR and WAXS techniques were employed for characterization of a series of hydrogels, obtained by varying the percentage of clay, crosslinking and constitution of kaolin. The water absorbency at equilibrium (Weq decreased with increasing clay content and the amount of crosslinking agent. Superabsorbent hydrogel (Weq > 1084 g H2O/g gel was obtained as 10 wt% of white kaolin and 0.05 mol% of crosslinking agent were used. The hydrogel proved sensitive to pH variation and the presence of salts.

Development of local metakaolin as a pozzolanic material

International Nuclear Information System (INIS)

Sharif, M.B.; Tahir, M.A.

2010-01-01

This paper describes the development of metakaolin in which Kaolin clay is burnt at temperatures of 700, 800 and 900 deg. C Celsius for 6, 8 and 10 hours duration. SAI (Strength Activity Index) of metakaolin is determined with 20% replacement of cement with meta kaolin as per ASTM C-311. It was found that maximum value of SAI is achieved at a temperature of 800 degree C Celsius when kaolin clay is burnt for 6-8 hour duration. XRD (X-Ray Diffraction) Analysis was also carried out which confirmed the outcome of strength results. (author)

Sensitivity of the activated partial thromboplastin time, the dilute Russell's viper venom time, and the kaolin clotting time for the detection of the lupus anticoagulant: a direct comparison using plasma dilutions.

Science.gov (United States)

Martin, B A; Branch, D W; Rodgers, G M

1996-01-01

Increasing dilutions of lupus anticoagulant (LA) plasmas from twelve patients were used to directly compare the sensitivity of four tests for LA. The tests evaluated were the modified Bell and Alton activated partial thromboplastin time (APTT), an APTT using a commercially prepared partial thromboplastin (Platelin LS APTT), a modified dilute Russell's viper venom time (DRVVT), and a modified kaolin clotting time (KCT). LAs were detected in all twelve plasmas by each of three tests and eleven of twelve plasmas in a fourth test when undiluted patient plasma was used. Repeating the tests after diluting the LA plasmas with normal platelet-free plasma (PFP) showed that the KCT was the most sensitive test for LA, detecting eleven of twelve LAs at a dilution of 10% patient plasma and ten of twelve LAs at a dilution of 5% patient plasma. The modified Bell and Alton APTT and the modified DRVVT had similar sensitivities at a patient plasma concentration of 10%, detecting seven of twelve and eight of twelve LAs, respectively. The Platelin LS APTT detected only four of twelve LAs at a patient plasma concentration of 10%. Our results indicate that the modified KCT is a sensitive method for the detection of LAs. The modified Bell and Alton APTT and the DRVVT were less sensitive.

Laboratory investigation of TerraZyme as a soil stabilizer

Science.gov (United States)

Yusoff, Siti Aimi Nadia Mohd; Azmi, Mastura; Ramli, Harris; Bakar, Ismail; Wijeyesekera, D. C.; Zainorabidin, Adnan

2017-10-01

In this study, a laboratory investigation was conducted to examine the performance of TerraZyme on different soil types. Laterite and kaolin were treated with 2% and 5% TerraZyme to determine changes in the soils' geotechnical properties. The obtained results were analysed and investigated in terms of compaction, Unconfined Compressive Strength (UCS) and California Bearing Ratio (CBR). The changes in geotechnical properties of the stabilised and unstabilised soils were monitored after curing periods of 0, 7, 15, 21 and 30 days. Changes in compaction properties, UCS and CBR were observed. It was found that laterite with 5% TerraZyme gave a higher maximum dry density (MDD) and decreased the optimum moisture content (OMC). For kaolin, a different TerraZyme percentage did not show any effect on both MDD and OMC. For strength properties, it was found that 2% TerraZyme showed the greatest change in UCS over a 30-day curing period. The CBR value of stabilised kaolin with 2% TerraZyme gave a higher CBR value than the kaolin treated with 5% TerraZyme. It was also found that laterite treated with TerraZyme gave a higher CBR value. Lastly, it can be concluded that TerraZyme is not suitable for stabilising kaolin; TerraZyme requires a cohesive soil to achieve a better performance.

Protein and synthetic polymer injection for induction of obstructive hydrocephalus in rats

Directory of Open Access Journals (Sweden)

Del Bigio Marc R

2007-09-01

Full Text Available Abstract Background The objective of this study was to develop a simple and inexpensive animal model of induced obstructive hydrocephalus with minimal tissue inflammation, as an alternative to kaolin injection. Materials Two-hundred and two male Sprague-Dawley rats aged 3 weeks received intracisternal injections of kaolin (25% suspension, Matrigel, type 1 collagen from rat tail, fibrin glue (Tisseel, n-butyl-cyanoacrylate (NBCA, or ethylene vinyl alcohol copolymer (Onyx-18 and Onyx-34. Magnetic resonance imaging was used to assess ventricle size. Animals were euthanized at 2, 5, 10 and 14 days post-injection for histological analysis. Results Kaolin was associated with 10% mortality and successful induction of hydrocephalus in 97% of survivors (ventricle area proportion 0.168 ± 0.018. Rapidly hardening agents (fibrin glue, NBCA, vinyl polymer had high mortality rates and low success rates in survivors. Only Matrigel had relatively low mortality (17% and moderate success rate (20%. An inflammatory response with macrophages and some lymphocytes was associated with kaolin. There was negligible inflammation associated with Matrigel. A severe inflammatory response with giant cell formation was associated with ethylene vinyl alcohol copolymer. Conclusion Kaolin predictably produces moderate to severe hydrocephalus with a mild chronic inflammatory reaction and fibrosis of the leptomeninges. Other synthetic polymers and biopolymers tested are unreliable and cause different types of inflammation.

Investigation of additives for preventing ash fouling and sintering during barley straw combustion

International Nuclear Information System (INIS)

Wang, Liang; Skreiberg, Øyvind; Becidan, Michael

2014-01-01

Formation of potassium chloride reduces ash sintering temperature and causes fouling deposits in biomass combustion applications. In the present work, the capacity of two mineral additives zeolite 24A and kaolin to capture KCl were investigated. A series of thermogravimetric experiments were carried out to measure fractions of KCl retained in the two additives as function of reaction temperature and heating time. The residues from additive-KCl mixtures after heating treatment were analyzed by X-ray diffractometry (XRD). When heated at 900 °C for 1 h, the overall KCl capturing efficiencies of the two additives were 60% and 45% for zeolite 24A and kaolin respectively, which slightly decreased to 50% and 43% as the heating time increased to 12 h. At 1000 °C, the fractions of KCl captured by zeolite 24A and kaolin significantly decreased from 50% and 40% to 26% and 17%, as the KCl-additive mixtures were heated for 1 and 12 h, respectively. The decrease in of the overall KCl capturing efficiencies is mainly attributed to reduction of surface areas and chemically active compounds of the two additives with increasing temperature and heating time. The XRD analysis results showed that both zeolite 24A and kaolin can react with KCl to form different potassium aluminium silicates. It indicates that chemical reactions play an important role in the overall capturing process. The effects of zeolite 24A and kaolin on sintering behaviors of the barley straw ash were also investigated. The residues from sintering tests were analyzed by a combination of X-Ray diffractometry (XRD) and scanning electron microscopy equipped with energy dispersive X-Ray analysis (SEM-EDX). The barley straw ash melted intensively at elevated temperatures. Together with XRD analysis, the SEM-EDX analysis results revealed that severe melting of the barley straw ash was due to formation and fusion of low temperature melting potassium silicates. Addition of kaolin and zeolite 24A significantly

Fluorescence of Bacteria, Pollens, and Naturally Occurring Airborne Particles: Excitation/Emission Spectra

Science.gov (United States)

2009-02-01

35 Figure 29. EEM spectra of kaolin particles, dry...Warrington, PA. Glass beads were obtained from Peirce Chemical Co., Rockford, IL. Kaolin particles were obtained from Particle Information Services...solution concentration of 1 mg/ml. The samples were vortexed and pipetted vigorously to disperse aggregates. Stock bacteria solutions were diluted to a

Jurassic and Cretaceous clays of the northern and central North Sea hydrocarbon reservoirs reviewed

Energy Technology Data Exchange (ETDEWEB)

Wilkinson, M.; Haszeldine, R.S.; Fallick, A.E.

2006-03-15

The principal clays of the northern and central North Sea are illite (sometimes with interlayered smectite) and kaolin. Chlorite is only locally important. Although it has been proposed that kaolin within North Sea sandstones is detrital in origin, the majority of workers have concluded that it is authigenic, largely the product of feldspar alteration. Kaolin is found within a wide range of sedimentary settings (and within shales) apparently defying the notion that kaolin is an indicator of meteoric water deposition. Within sandstones, the earliest authigenic kaolin has a vermiform morphology, the distribution of which is controlled by the availability of detrital mica to act as a nucleus, and the composition of the post-depositional porewaters. This vermiform kaolin formed in meteoric water, the presence of which is easily accounted for below sub-aerial exposure surfaces in non-marine formations, and below unconformities over marine units. In fully marine sands, and even marine shale units, kaolin still occurs. It has therefore been suggested that even these locations have been flushed with meteoric water. Early vermiform kaolin recrystallizes to a more blocky morphology as burial proceeds, at least in the Brent Group. Blocky kaolin has been reported as growing before, synchronously with, and after the formation of quartz overgrowths, though oxygen isotope studies support low-temperature growth, pre-quartz. Blocky kaolin may form during meteoric flushing associated with lower Cretaceous uplift and erosion, though it is found in fault blocks that are thought to have remained below sea level. Here, the kaolin may form in stagnant meteoric water, relics of the post-depositional porewater. It has also been proposed that the blocky kaolin grew in ascending basinal waters charged with carboxylic acids and CO{sub 2}, though this hypothesis is not supported by stable oxygen isotope data. Some of the blocky kaolin is dickite, the stable polymorph above 100{sup o}C. Fibrous

Author Details

African Journals Online (AJOL)

Babalola, OA. Vol 12, No 2 (2008) - Articles Effects of Kaolin particle size and annealing temperature on the Resistivity of Zinc- Kaolin Composite Resistors Abstract PDF. ISSN: 1119-8362. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's ...

Chemical Processes Related to Combustion in Fluidised Bed. Report for the period 2002-07-01 to 2004-06-30

Energy Technology Data Exchange (ETDEWEB)

Steenari, Britt-Marie; Lindqvist, Oliver [Chalmers University of Technology, Goeteborg (Sweden). Dep. of Environmental Inorganic Chemistry

2005-02-01

One part of the project was an investigation of the mechanism and kinetics of the absorption of potassium and cadmium in kaolin. Addition of kaolin has been suggested as a method to decrease problems like ash sintering, fouling and corrosion. The results showed that kaolin binds potassium effectively, especially if it is present as chloride or hydroxide. Reducing atmosphere and the presence of water vapour favours the absorption. The products are mainly silicates with low solubility. Cadmium is also absorbed by kaolin in a similar way. In the second part of the project, the chemical forms of some metals present in fly ash from combustion of MSW and bio fuels were studied. The most common Cd-compounds found were sulphate, oxide, chloride and silicate. It was also shown that Cd often is incorporated in calcium minerals, such as calcium silicates, CaO and CaC0{sub 3}, due to the fact that the ions Ca{sup 2+} and Cd{sup 2+} are almost similar in size and charge.

Fly ash as a potential starting reagent for the synthesis of ultramarine blue

Energy Technology Data Exchange (ETDEWEB)

Landman, A.A.; De Waal, D. [University of Pretoria, Pretoria (South Africa). Dept. of Chemistry

2004-04-02

The traditional starting reagent for the synthesis of ultramarine blue, namely kaolin, has to be heated before the synthesis to weaken the structure of the kaolin. Two batches of fine fly ash (an aluminosilicate waste product from the combustion of coal) were successfully used to synthesize ultramarine blue. Infrared, Raman and X-ray diffraction results confirmed the formation of the product. Fly ash has the advantage over kaolin of being amorphous. The results further showed that the transition from the green ultramarine species to the blue species coincided with an increase in the ratio of the amount of S-3{sup -1} species relative to the amount of S-2{sup -1} species.

Micromechanics of non-active clays in saturated state and DEM modelling

Directory of Open Access Journals (Sweden)

Pagano Arianna Gea

2017-01-01

Full Text Available The paper presents a conceptual micromechanical model for 1-D compression behaviour of non-active clays in saturated state. An experimental investigation was carried out on kaolin clay samples saturated with fluids of different pH and dielectric permittivity. The effect of pore fluid characteristics on one-dimensional compressibility behaviour of kaolin was investigated. A three dimensional Discrete Element Method (DEM was implemented in order to simulate the response of saturated kaolin observed during the experiments. A complex contact model was introduced, considering both the mechanical and physico-chemical microscopic interactions between clay particles. A simple analysis with spherical particles only was performed as a preliminary step in the DEM study in the elastic regime.

Safety evaluation of new hemostatic agents, smectite granules, and kaolin-coated gauze in a vascular injury wound model in swine.

Science.gov (United States)

Kheirabadi, Bijan S; Mace, James E; Terrazas, Irasema B; Fedyk, Chriselda G; Estep, J Scot; Dubick, Michael A; Blackbourne, Lorne H

2010-02-01

In 2007, a potent procoagulant mineral called WoundStat (WS), consisting of smectite granules, received clearance from the Food and Drug Administration for marketing in the United States for temporary treatment of external hemorrhage. Previously, we found that microscopic WS particles remained in the injured vessels that were treated, despite seemingly adequate wound debridement. Thus, we investigated the thromboembolic risk of using WS when compared with kaolin-coated gauze, Combat Gauze (CG); or regular gauze, Kerlix (KX) to treat an external wound with vascular injuries in pigs. The right common carotid artery and external jugular vein of pigs were isolated and sharply transected (50%). After 30 seconds of free bleeding, the neck wounds were packed with WS, CG, or KX and compressed until hemostasis was achieved (n = 8 per group). Wounds were debrided after 2 hours, and vascular injuries were primarily repaired with suture. Blood flow was restored after infusing 1 L of crystalloid (no heparin or aspirin) and the wounds were closed. Two hours later, computed tomographic angiography was performed, and the wounds were reopened to harvest the vessels. The brains and lungs were recovered for gross and microscopic examination after euthanasia. No differences were found in baseline measurements. Thrombelastography showed similar hypercoagulability of the final blood samples when compared with baselines in all groups. All vessels treated with KX or CG were patent and had no thrombus or blood clot in their lumen. In contrast, seven of eight carotid arteries and six of eight jugular veins treated with WS developed large occlusive red thrombi and had no flow. Small clots and WS residues were also found in the lungs of two pigs. Histologically, significant endothelial and transmural damage was seen in WS-treated vessels with luminal thrombi and embedded WS residues. WS granules caused endothelial injury and significant transmural damage to the vessels that render them

Isotopic method for investigation of process of periodic sedimentation of argillaceous suspensions

International Nuclear Information System (INIS)

Kohman, L.; Woznicki, T.

1976-01-01

The process of periodic sedimentation of kaolinic suspension in water has been investigated, by isotopic tracer method. the tracer was either the irradiated matrix material or 198 Au, adsorbed on the kaolin grains. The velocity of suspension level lowering (the sedimentation curve) and the variation in density in vertical section of sediment layer have been determined. (author)

Enhanced Reactant-Contaminant Contact through the Use of Persulfate In Situ Chemical Oxidation (ISCO)

Science.gov (United States)

2011-02-01

248  Figure 7.4.1.5. Concentration versus depth profile for diffusion of 1 M persulfate in kaolin at...Figure 7.4.1.6. Concentration versus depth profile for diffusion of 0.1 M persulfate in kaolin at 82 days...acid. The complex chemistry of persulfate may change the permeability of soils and subsurface solids by inducing dispersion and flocculation, or by

Kaolins in Uruguay

International Nuclear Information System (INIS)

Spoturno, J.; Coronel, N.

1980-01-01

This work belongs to the Syllabus or Mundial monograph about caolines. Its was organized by the number 23 working group caolines genesis of the International geological correlation Unesco programme. History, geology, tectonic development, sedimentation, dating and geochemistry aspects were given in this report.

Characterization of bentonite, fibrous and kaolinite clays with regard to their use in pelotherapy; Caracterizacion de bentonitas, arcillas fibrosas y arcillas caoliniferas para su empleo en peloterapia

Energy Technology Data Exchange (ETDEWEB)

Pozo Martin, E.; Martin Rubi, J. A.; Pozo Rodriguez, M.

2011-07-01

We have characterized the mineralogical and chemical contents of several Spanish special clays (bentonite, fibrous clays and kaolin). Mineralogical analyses revealed that the samples were composed mainly of phyllosilicates (78 %-99 %) with a notable presence of dioctahedral and trioctahedral smectites in the bentonite, kaolinite in the kaolin and sepiolite or palygorskite in the fibrous clays. Illite was the common subordinate mineral in the bentonite, kaolin and palygorskite. Quartz, calcite, dolomite and feldspars were found as associate minerals with the occasional presence of zeolites and amphiboles. The chemical analysis was consistent with the mineralogy. With regard to trace elements (V, Cr, Ni, Co, Cu, Zn, As, Mo, Ba, Sb, Pb, U), the whole samples of the magnesium bentonite and sepiolite were found to have the lowest trace-element contents (<257,28 ppm ), whilst the aluminium bentonite, kaolin and particularly the palygorskite had higher contents than the other clays, with some elements occasionally exceeding the contents of previously studied common clays. Nevertheless, all the trace elements were found in lower quantities than the recommended toxicity levels and those quantities currently used in pelotherapy in Spanish spas. (Author)

Effects of silicon carbide on the phase developments in mullite-carbon ceramic composite

Directory of Open Access Journals (Sweden)

Fatai Olufemi ARAMIDE

2017-12-01

Full Text Available The effects of the addition of silicon carbide and sintering temperatures on the phases developed, in sintered ceramic composite produced from kaolin and graphite was investigated. The kaolin and graphite of known mineralogical composition were thoroughly blended with 4 and 8 vol % silicon carbide. From the homogeneous mixture of kaolin, graphite and silicon carbide, standard samples were prepared via uniaxial compaction. The test samples produced were subjected to firing (sintering at 1300°C, 1400°C and 1500°C. The sintered samples were characterized for the developed phases using x‐ray diffractometry analysis, microstructural morphology using ultra‐high resolution field emission scanning electron microscope (UHRFEGSEM. It was observed that microstructural morphology of the samples revealed the evolution of mullite, cristobalite and microcline. The kaolinite content of the raw kaolin undergoes transformation into mullite and excess silica, the mullite and the silica phases contents increased with increased sintering temperature. It is also generally observed that the graphite content progressively reduced linearly with increased sintering temperature. It is concluded that silicon carbide acts as anti-oxidant for the graphite, this anti-oxidant effect was more effective at 4 vol % silicon carbide.

Usability of Particle Film Technology and Water Holding Materials to Improve Drought Tolerance in Gossypium hirsutum L. Plants

Science.gov (United States)

Roy, K.; Zwieniecki, M.

2017-12-01

Cotton (Gossypium hirsutum L.) is relatively drought resistant and thus is planted widely in many semi-arid and arid parts of the world, many of which are usually deprived of modern water management technologies. Since the productivity of cotton plants depends on water availability, we carried out the present research aiming at testing two different low cost and arid-environment friendly water efficient techniques: application of particle film technology on leaves to reduce the transpiration rate (kaolin dust), and use of organic material to improve the soil water holding capacity (cotton wool). In details, kaolin (3% and 5%; weight:volume) mixed in water was sprayed on the upper surface of the leaves of young plants, and small amounts of cotton wool (0.1%, 0.3% and 0.5%; weight:weight) were mixed into the soils. The study showed that kaolin spray was useful as a transpiration reducing agent only if plants have adequate water in the soil (well irrigated) but not under water stress conditions. In addition, mixing a small amount of cotton wool into the soil can significantly increase the amount of water available to the plants, and extend the benefit of kaolin application on plants.

Argillization by descending acid at Steamboat Springs, Nevada

Science.gov (United States)

Schoen, Robert; White, Donald E.; Hemley, J.J.

1974-01-01

Steamboat Springs, Nevada, an area of present-day hot springs, clearly illustrates the genetic dependence of some kaolin deposits on hot-spring activity. Andesite, granodiorite and arkosic sediments are locally altered at the land surface to siliceous residues consisting of primary quartz and anatase, plus opal from primary silicates. These siliceous residues commonly exhibit the textural and structural features of their unaltered equivalents. Beneath the siliceous residues, kaolin and alunite replace primary silicates and fill open spaces, forming a blanketlike deposit. Beneath the kaolin-alunite zone, montmorillonite, commonly accompanied by pyrite, replaces the primary silicates. On the ground surface, the same alteration mineral zones can be traced outward from the siliceous residue; however, hematite rather than pyrite accompanies montmorillonite.Chemical analysis indicates that sulfuric acid is the active altering agent. The acid forms from hydrogen sulfide that exsolves from deep thermal water, rises above the water table and is oxidized by sulfur-oxidizing bacteria living near the ground surface. This acid dissolves in precipitation or condensed water vapor and percolates downward destroying most of the primary minerals producing a siliceous residue. Coincidence of the water table with the downward transition from siliceous residue to kaolin-alunite signifies decreasing hydrogen metasomatism because of dilution of descending acid by ground water.In hot-spring areas, beds of siliceous sinter deposited at the surface by hypogene thermal water look, superficially, like areas of surficial acid alteration. Features diagnostic of a surficial alteration are the relict rock structures of a siliceous residue and a kaolin-alunite zone immediately beneath.

New Technologies for Treating Severe Bleeding in Far-Forward Combat Areas

Science.gov (United States)

2010-04-01

conditions have been utilized to evaluate the safety and efficacy of Combat Gauze. Combat Gauze ( kaolin -coated gauze) was recently distributed by US...woven medical gauze (50% polyester and 50% rayon) impregnated with a contact (intrinsic) pathway activating clotting agent, kaolin . The prototype...Military Tourniquet (EMT). 5.0 CONCLUSION Future combat scenarios where the troops will be more dispersed , imply that evacuation times of

Organic-mineral binder for molybdenum concentrate granulation

International Nuclear Information System (INIS)

Guro, Vitaliy P.; Ibragimova, Matluba A.; Safarov, Edgorjon T.

2016-01-01

Process of pyrite cinders production from Mo middlings consists of molybdenite concentrate granulation, firing to oxidize sulfide minerals and to recover Re-oxide. If kaolin binder is used a pyrite cinders dilution with Mo takes place. So, the development of organic binding agents, alternative to kaolin, is an actual issue. The approach is based on the comparison of the hydrophilic, strength and technological features of the hydrometallurgical processing of pellets. The new batch is developed. It differs from the traditional mixture by polymer burning and minimizing Mo dilution, thus aiming to maximize Re, Au, Ag recovery. The composition of the new organic-mineral batch is as follows: 97.3 % of molybdenite concentrate, 2 % of kaolin and 0.7 % of SK polymer. Keywords: molybdenum middlings, binder, organic additive, batch, granulation.

MEASUREMENT OF THE VISCOELASTIC PROPERTIES OF WATER-SATURATED CLAY SEDIMENTS.

Science.gov (United States)

The complex shear modulus of both kaolin -water and bentonite-water mixtures has been determined in the laboratory. The method involved measuring the...range two to forty-three kHz. Dispersed sediments behaved like Newtonian liquids. Undispersed sediments, however, were viscoelastic in character, and...their shear moduli exhibited no dependence on frequency. For undispersed kaolin mixtures, a typical result is (21.6 + i 1.2) x 1,000 dynes per square

Effectiveness of Selected Entomopathogenic Fungi in Packed Rice Grain at Room Temperature Against Corcyra Cephalonica Stainton

Directory of Open Access Journals (Sweden)

Hendrawan Samodra

2017-11-01

Full Text Available Eight isolates of entomopathogenic fungi were evaluated as dried conidia against the rice moth,  Corcyra cephalonica. In bioassays two isolates of Beauveria bassiana (BbGc and BbPs and one isolate of Metarhizium anisopliae (MaPs consistently gave high mortality to C. cephalonica larvae. Formulations in either kaolin, talc or tapioca flour (20 % w/w a.i. thoroughly mixed with long grain rice in plastic cups (8 cm diameter by 5 cm gave complete larval mortality by the 12th day of treatment. However, in general those formulated in kaolin and talc were more efficacious and faster to kill compared to those formulated in tapioca flour or the unformulated control. Even at the lowest rate of 0.05 g BbGc in kaolin provided 100% mortality 7 days after introduction compared with other dust formulations. Isolate BbGc in kaolin and talc administered at 0.4 g a.i. in 200 g rice packed in plastic kept at room temperature provided protection against the rice moth up to 4 months of storage. Larval mortality in excess of 90% was obtained 15 days after introduction. Formulations of MaPs was effective only within the first month of storage beyond which infectivity rapidly declined.

Multitracer studies on the effects of model acid rain on the adsorption of trace elements on soils

International Nuclear Information System (INIS)

Wang, H.F.; Ambe, S.; Takematsu, N.; Ambe, F.

2001-01-01

Using a multitracer technique, the effects of acid rain pH on the adsorption of 15 trace elements on soil were studied. Kaolin, forest soil (original and with partially removed oxides), black soil (original and without organic matter) and Kureha soil (original, with partially removed oxides, and without organic matter) were employed as the adsorbents. Instead of H 2 SO 4 solution, HCl solution was selected as the model acid rain based on the results of adsorption experiments on kaolin. In general, the percentage adsorption of cationic elements on three original soils and kaolin increased with increasing pH. The adsorption of oxyanionic elements, As and Se, on three soils was high over the entire pH range studied, while that on kaolin was low and decreased with an increase in pH. The differences in the physical and chemical properties of soils were reflected on the adsorption. The organic matter in soil had positive effects on the extent of adsorption of most elements studied, while the oxides apparently showed positive effects only for Fe and Se adsorption. The results indicate that acid rain decreases the retention of cations in soil and that it increases or does not change the adsorption of anions. (orig.)

Dispersion of phyllosilicates in aqueous suspensions: role of the nature and amount of surfactant.

Science.gov (United States)

Houta, Nadia; Lecomte-Nana, Gisèle-Laure; Tessier-Doyen, Nicolas; Peyratout, Claire

2014-07-01

The present work aims at investigating the effect of pH values and additives on the dispersion of two 1:1 dioctahedral phyllosilicates in the presence of water. Two model clays are used for this purpose, BIP kaolin and NZCC halloysite, presenting the same surface chemistry but different morphologies. The effect of sodium hexametaphosphate, sodium silicate and sodium carbonate is discussed. Kaolin and halloysite powders were first characterized using X-ray diffraction, thermogravimetric analysis and scanning electron microscopy. Subsequently, suspensions containing 8 mass% of each clay were prepared with or without additives. Experimental measurements regarding the pH values, the zeta potential and the rheological behavior were performed to determine the most suitable additive. Results show that the conformation of halloysite particles changes regarding pH values of suspensions and is strongly related to the surface charges of these particles. At their natural pH values, halloysite and kaolin suspensions exhibit zeta potentials equal to -50 and -20 mV respectively. This trend indicates that halloysite-based suspensions are well dispersed compared to kaolin-based suspensions. Sodium hexametaphosphate is the most suitable dispersant for both clays. The rheological characterization regarding further applications in casting process indicates a shear-thinning behavior for all studied compositions. Copyright © 2014 Elsevier Inc. All rights reserved.

Effect of coal mine dust and clay extracts on the biological activity of the quartz surface

Energy Technology Data Exchange (ETDEWEB)

Stone, V.; Jones, R.; Rollo, K.; Duffin, R.; Donaldson, K.; Brown, D.M. [Napier University, Edinburgh (United Kingdom). School of Life Science

2004-04-01

Modification of the quartz surface by aluminum salts and metallic iron have been shown to reduce the biological activity of quartz. This study aimed to investigate the ability of water soluble extracts of coal mine dust (CMD), low aluminum clays (hectorite and montmorillonite) and high aluminum clays (attapulgite and kaolin) to inhibit the reactivity of the quartz surface. DQ12 induced significant haemolysis of sheep erythrocytes in vitro and inflammation in vivo as indicated by increases in the total cell numbers, neutrophil cell numbers, MIP-2 protein and albumin content of bronchoalveolar lavage (BAL) fluid. Treatment of DQ12 with CMD extract prevented both haemolysis and inflammation. Extracts of the high aluminum clays (kaolin and attapulgite) prevented inhibition of DQ12 induced haemolysis, and the kaolin extract inhibited quartz driven inflammation. DQ12 induced haemolysis by coal mine dust and kaolin extract could be prevented by pre-treatment of the extracts with a cation chellator. Extracts of the low aluminum clays (montmorillonite and hectorite) did not prevent DQ12 induced haemolysis, although the hectorite extract did prevent inflammation. These results suggest that CMD, and clays both low and rich in aluminum, all contain soluble components (possibly cations) capable of masking the reactivity of the quartz surface.

Bovine bone for white ceramic

International Nuclear Information System (INIS)

Souza, J.L. de; Harima, E.; Leite, J.I.P.; Monteiro, F.M.; Bezerra, M.T.T.

2011-01-01

The porcelain is composed of feldspar, kaolin and about 50% for bovine bone ashes. This work aims to analyze the properties acquired by the substitution of kaolin by its waste. For characterization of raw materials chemical analyzes were made by X-Ray Fluorescence (XRF) and mineralogical analysis by X-Ray Diffraction (XRD). Four formulations were produced varying the percentage of waste materials of kaolin and bone ashes of 25 and 55% by weight. The samples were sintered at temperatures of 1150, 1200 and 1250 deg C. The technological tests realized were: water absorption (WA), apparent porosity (AP), apparent density (AD) and linear retraction (LR). Improvement in the physical-mechanical properties of the samples with increasing temperature were observed, and 1250 deg C obtained 0.69% of WA, 1.22% AP, 2.26 g / cm3 AD, and 0.52% LR

Bovine bone for white ceramic; Osso bovino para ceramica branca

Energy Technology Data Exchange (ETDEWEB)

Souza, J.L. de; Harima, E.; Leite, J.I.P.; Monteiro, F.M.; Bezerra, M.T.T., E-mail: leonaldo.souza@yahoo.com.br [Instituto de Educacao, Ciencia e Tecnologia do Rio Grande do Norte (LPMR/IFRN), Natal, RN (Brazil). Laboratorio de Processamento Mineral e de Residuos

2011-07-01

The porcelain is composed of feldspar, kaolin and about 50% for bovine bone ashes. This work aims to analyze the properties acquired by the substitution of kaolin by its waste. For characterization of raw materials chemical analyzes were made by X-Ray Fluorescence (XRF) and mineralogical analysis by X-Ray Diffraction (XRD). Four formulations were produced varying the percentage of waste materials of kaolin and bone ashes of 25 and 55% by weight. The samples were sintered at temperatures of 1150, 1200 and 1250 deg C. The technological tests realized were: water absorption (WA), apparent porosity (AP), apparent density (AD) and linear retraction (LR). Improvement in the physical-mechanical properties of the samples with increasing temperature were observed, and 1250 deg C obtained 0.69% of WA, 1.22% AP, 2.26 g / cm3 AD, and 0.52% LR.

Threshold-Switchable Particles (TSP’s) to Control Internal Hemorrhage

Science.gov (United States)

2011-12-01

Ismagilov and Morrissey groups for threshold testing. TSPs will be formed from porous and solid nanoparticles with a low-size dispersion optimized for...samples by HUVEC (Human Umbilical Vein Endothelial Cells). Ag NP concentration – 10 µg/ml; Kaolin concentration - 10 µg/ml; MCF-26 concentration 100...µg/ml. (Right) Uptake of various samples by HDFs. Ag NP concentration – 20 µg/ml; Kaolin concentration - 20 µg/ml; MCF-26 concentration 100 µg/ml

Microstructure Study For Optimization Of Dielectric Property Of Electrical Porcelain

International Nuclear Information System (INIS)

Tak, S. K.; Shekhawat, M. S.; Mangal, R.

2010-01-01

Five sample mixtures of kaolin, ball clay, feldspar and Quartz were formulated and porcelain samples fabricated. Crystalline phases and mullite morphology were studied using XRD and SEM respectively. A composition of 30% kaolin, 15% ball clay, 30% feldspar and 25% quartz yielded a body with high dielectric strength of 19 kV/mm compare to an ISO graded product having dielectric strength 14.6 KV/mm after firing at 1225 deg. C.

Rheology Modifiers Applied to Kaolin-Bentonite Slurries for SRNL WTP Pulse Jets Tank Pilot Work in Support of RPP at Hanford

International Nuclear Information System (INIS)

WILLIAM, DANIEL

2005-01-01

Savannah River National Laboratory (SRNL) was tasked to find and characterize the impact of rheological modifiers to a clay (Kaolin-Bentonite) slurry having 23.1 total wt percent solids, 1.165 g/ml, and Bingham Plastic yield stress of 13 Pa and plastic viscosity of 24 mPa-sec. The primary objective was to find rheological modifiers when blended with this clay slurry that would provide a vane yield stress of 300 Pa when the slurry was undisturbed for 24 hours. A secondary objective was to find a modifier that after shearing would produce a Bingham Plastic yield stress of 30 Pa and plastic viscosity of 30 mPa-sec. Two parallel paths were chosen with one examining a variety of organic/inorganic modifiers and another using just the inorganic modifier Laponite (R). The addition of organic modifiers hydroxyethylcellulose, hydroxypropylmethylcellulose, and hydroxypropylcellulose at a target 0.50 wt percent dramatically increased the vane yield stress over the range 311 - 724 Pa, and also increased the Bingham plastic yield stress and plastic viscosities over the range 33-112 Pa and 27-166 mPa-sec, respectively. The organic modifiers also showed elastic behavior, yielding a very unpredictable up flow curve. The 0.50 wt percent addition of inorganic modifiers magnesium aluminum silicate and hydrate magnesium aluminum silicate only increased the vane yield stress to 36-46 Pa and had little impact on the Bingham Plastic parameters. A range of an inorganic (2-4 wt percent magnesium aluminum silicate) and combination of a range of an inorganic (2-3 wt percent magnesium aluminum silicate) and organic (0.03-0.05 wt percent sodium carboxymethylcellulose) modifiers were then tested. These results showed that the target vane yield stress could be obtained but the Bingham Plastic yield stress and plastic viscosity were 3 times too high. Reducing the organic modifier weight percent by a few hundredths, the Bingham Plastic yield stress could be obtained, but then the vane yield stress

Sorption of VX to Clay Minerals and Soils: Thermodynamic and Kinetic Studies

Science.gov (United States)

2012-12-01

Kaolinite, a member of the kaolin family, is a 1:1 clay, consisting of a single silicon-containing tetrahedral sheet linked to a single aluminum...14,15,18,19 The kaolinite is a white-firing, plastic kaolinite mined from claystone deposits in Georgia. This clay, identified as no. 6 tile kaolin , was...Validation of Model Predictions for the Dispersion and Fate of Reactive Chemical Releases in a Sub- Estuary of the Chesapeake Bay. Presented at the 2011

Initial Resuscitation with Plasma and Other Blood Components Reduced Bleeding Compared to Hetastarch in Anesthetized Swine with Uncontrolled Splenic Hemorrhage

Science.gov (United States)

2011-04-01

temperature before measurements. A 1-mL aliquot was then pipetted into a kaolin tube to ini- tiate coagulation and 340-mL samples were pipetted into TEG...human ranges: PT, PTT, and fibrinogen ranges from Dade Behring. PLT count from Abbott Laboratories. Citrated Kaolin TEG values from Haemoscope. SONDEEN...crystalloid only (data courtesy of LTC R.S. Kotwal, MD, MPH). Military units operating in isolated, dispersed areas have been known to carry 2 to 4 units of

The effect of sintering time on recycled magnesia brick from kiln of the cement plant

Science.gov (United States)

Aji, B. B.; Rosalina, D.; Azhar; Amin, M.

2018-01-01

This research aim was to investigate the effect of sintering time on reuse waste of magnesia brick from the rotary kiln of the cement plant. Reuse of the magnesia brick was carried out by mixed the kaolin as the binder. Spent refractory was used as aggregate with the composition of 85% spent refractory and 15% kaolin clay, respectively. The reuse brick then was molded with the size of 5x5x5 cm using hydraulic press under a load of 10 tons in order to forms green body. Green body then dried and sintered at 1200 °C with time variation of 2 hours, 4 hours, 6 hours, 8 hours and 10 hours, respectively. Thus, for comparison reuse brick was tested to its apparent porosity, the bulk density, and Cold Crushing Strength (CCS). The effect of kaolin addition as binder was also discussed.

Cementation of nitrate solutions by alkali-activated slag-metakaolin cement

International Nuclear Information System (INIS)

Rakhimova, N.R.; Rakhimov, R.Z.; Naumkina, N.I.; Gubaidullina, A.M.; Yakovlev, G.I.; Shaybadullina, A.V.

2015-01-01

This paper considered the feasibility of solidification of liquid salt wastes by NaNO 3 solutions of concentration 100-700 g/l by alkali-activated slag (AASC) and alkali-activated slag-meta-kaolin cements (AASMC). The AASC (activated by 5% Na 2 O) and AASMC (activated by 5% Na 2 O and introduced with 5% of MK) mixed with NaNO 3 solutions were more effective in comparison with Portland cement. The compressive strength of hardened AASC and AASMC pastes was 1.6-12. and 7- 21 MPa in 3-day age and 13.4-31 and 20-37 MPa in 28-day age, respectively, depending on concentration of NaNO 3 solution. The incorporation of 3-5% meta-kaolin in AASC: (i) increased the compressive strength of hardened AASMC pastes up to 50% depending on the type of meta-kaolin, (ii) shortened setting times of fresh AASMC pastes

Inert powders alone or in combination with neem oil for controlling Spodoptera eridania and Spodoptera frugiperda (Lepidoptera: Noctuidae larvae

Directory of Open Access Journals (Sweden)

Kelly Christiane Constanski Silva

2016-08-01

Full Text Available Laboratory studies was carry out to evaluated the potential of inert powders: bentonite, kaolin and diatomaceous earth (DE applied as dust and aqueous suspension alone and associated with neem oil to the control Spodoptera eridania and Spodoptera frugiperda second instar larvae. In dust applications, 100% mortality of S. eridania, at the concentrations of 1.5 and 2.0 grams of bentonite, and 93.3% of S. frugiperda, at the concentration of 2.0 g were observed. DE at the height concentration (2.0 g caused 76.2% mortality of S. eridania and 46.6% of S. frugiperda. Kaolin, in all concentrations, was the only treatment that did not differed from the control for S. eridania but was different, in the high concentration, for S. frugiperda. When the plants were treated, larvae of S. eridania fed in the treatment DE, had an increase of two days in larval period. For the sex ratio, the percentage of males was greater in the treatments with kaolin, for both species. When powders was applied suspended in water separately or combined with neem oil, the best results were observed in combined of the bentonite (10% + neem, with 100% mortality for both species, and kaolin (10% + neem with 78.5% and 95.6% mortality for S. frugiperda and S. eridania, respectively. These treatments were classified as non-additive synergistic.

Investigation of Expanding Cements. Report 1. Summary of Information Available as of 1 July 1963

Science.gov (United States)

1965-09-01

the authors: (a) Portland cement mixed with CaSO4 and the dried hydratioQ products of lime and burnt kaolin (Budnikov and Kosuirevu[1 5i); it is...expansive ef- fects are strongly influenced by the amount of mixing water and by the nature of the alu.minous component; that is, kaolin , slag and bauxite...mechanical proper- ties of high-molecular system dispersion ." Colloidal Rev., Acad. Opement Sci. USSR, vol XVII, No. 2 (1955). .MI, 43. Mikhailov, V

Lead speciation in 0.1N HCl-extracted residue of analog of Pb-contaminated soil

International Nuclear Information System (INIS)

Wei Yuling; Yang, Y.-W.; Lee, J.-F.

2005-01-01

The heavy metal in-taken by plants from contaminated soils is usually assessed by extraction with 0.1N HCl. This study characterized the chemical form of lead in the solid residue of 0.1N HCl-extracted Pb-contaminated kaolin. The results indicate that most lead in the 0.1N HCl-extracted residue of the Pb(NO 3 ) 2 -contaminated kaolin dried at 105 deg C is mainly in form of PbCl 2 . For other lead-containing kaolin sample heated at 900 deg C, the XAS analysis also shows that majority of the lead compound was converted into PbCl 2 precipitate that remained in the solid residue during the 0.1N HCl extraction. Because PbCl 2 is only slightly soluble in dilute acids or water, it is suggested that using 0.1N HCl liquid as an extracting reagent to represent the heavy metal uptake by plants might actually underestimate the uptake

Application of automotive paint sludge in the production of white ceramic

International Nuclear Information System (INIS)

Praxedes, P.B.; Ponte, H.A.; Mymrine, V.

2016-01-01

Full text: Paint wastes of an automotive industry were evaluated in terms of their chemical and mineralogical characteristics in order to analyse its potential use as a reinforcing agent in white ceramic. Both kaolin and sludge paint were analysed using the techniques of XRF, XRD, SEM, EDS. In order to understand the behaviour of the sludge during firing, TGA and DTA analysis were done. Samples containing kaolin and 0, 1, 2, 4 and 8 (wt.%) sludge paint were prepared. The ceramics were compacted at 10MPa and sintered at 1000 °C, 1200 °C, 1250 °C and 1300 °C. Water absorption, linear shrinkage and flexural strength were the mechanical properties evaluated in the samples. The experimental results showed that the samples with lagers amounts of sludge performed better or similar to the samples that only contained kaolin. The insertion of 8 (wt.%) of sludge in the specimen increased flexural strength in 63%. (author)

Dabigatran and its reversal with recombinant factor VIIa and prothrombin complex concentrate

DEFF Research Database (Denmark)

Sølbeck, Sacha; Nilsson, Caroline U; Engström, Martin

2014-01-01

OBJECTIVE: Dabigatran is a new oral direct thrombin inhibitor. No specific antidote exists in the event of hemorrhage, but prothrombin complex concentrate (PCC) and recombinant activated factor VII (rFVIIa) are suggested therapies. Sonoclot is a bedside viscoelastic instrument for monitoring...... different Sonoclot cuvettes: Glassbead, kaolin and tissue factor (diluted) activated. RESULTS: The Sonoclot detected in vitro-induced anticoagulation due to dabigatran with the glassbead- and kaolin-activated cuvettes. There was no reversing effect of PCC, probably due to the presence of heparin in the PCC...

Improving UXO Detection and Discrimination in Magnetic Environments

Science.gov (United States)

2010-05-01

disks were used for 82 all analyses using a Bruker AXS S-4 Pioneer, a 4 kW, wavelength dispersive instrument. XRF element analyses were determined by...event at around 500°C is possibly caused by loss of structural water from kaolin and/or mica type clay minerals. Between about 600 and 1400°C the TGA...Loss of structural water from Kaolin or Micas1 510 Endothermic TGA, DTA Decomposition of böhmite (γ-AlO·OH)1 Loss of structural water from

Saylorville Stage 3 Contract Completion Report: Testing of Priority 1 Archaeological Sites 1980-1981.

Science.gov (United States)

1982-02-01

systematically- dispersed cores over a large area of the site was abandoned. He felt that one or more well-placed transects of probes placed across any...fragments 3 3 - 3-- Stoneware vessel fragment I I - I Kaolin pipe fragments 2 2 - 2-- Tile 2 2 - 2-- Glass Green glass container fragment 1 1 - 1I Clear...Stoneware vessel fragment 1 1 - Kaolin pipe fragments 2 2 2 - Tile 2 2 2 - Glass Green glass container fragment 1 1 - 1 - - Clear window glass fragments 3 3

Measures for simultaneous minimisation of alkali related operating problems; Aatgaerder foer samtidig minimering av alkalirelaterade driftproblem. Ramprogram

Energy Technology Data Exchange (ETDEWEB)

Davidsson, Kent; Eskilsson, David; Gyllenhammar, Marianne; Herstad Svaerd, Solvie; Kassman, Haakan; Steenari, Britt-Marie; Aamand, Lars-Erik

2006-12-15

Combustion of biofuel and waste wood is often accompanied by chlorine and alkali related operating problems such as slagging, deposit formation and corrosion on heat exchanger surfaces and bed agglomeration in fluidised bed boilers. In order to gain a greater insight into possible measures to overcome alkali related operating problems studies were carried out during 2005-2006. The results of the studies are presented in this report which includes work performed in the two following projects: 1 A5-509 Frame work - measures for simultaneous minimisation of alkali related operating problems 2 A5-505 Bed agglomeration risk related to combustion of cultivated fuels (wheat straw, red canary grass, industrial hemp) in commercial bed materials Full-scale experiments were carried out at Chalmers 12 MW{sub th} CFB boiler within the project A5-509. The purpose was to study the effect of various measures on bed agglomeration and deposit formation in connection with co-combustion of wood and straw pellets. The various measures included changing the bed material (blast furnace sand and olivine sand), adding various additives (kaolin, ammonium sulphate, elemental sulphur) and also co-combustion with sewage sludge. Furthermore results from kaolin experiments at the 26 MWth CFB boiler owned by Naessjoe Affaersverk were made available during the project and are also presented in this report. The results from the experiments at Chalmers revealed that, already at the lowest dosage of kaolin, approx. 2 kg/MWh, the bed material agglomeration temperatures increased significantly. The dosage of kaolin can presumably be reduced somewhat further while still maintaining the high agglomeration temperature. Experiments with a higher dosage of kaolin, 7 kg/MWh, proved that kaolin could also reduce the risk of deposit problems. The experiments at Naessjoe showed also that addition of kaolin increased the agglomeration temperature of the bed material. Addition of sulphur in any form resulted in a

How are macroinvertebrates of slow flowing lotic systems directly affected by suspended and deposited sediments?

Energy Technology Data Exchange (ETDEWEB)

Kefford, Ben J., E-mail: ben.kefford@rmit.edu.a [Biotechnology and Environmental Biology, School of Applied Sciences, RMIT University, PO Box 71, Bundoora, Victoria 3083 (Australia); Zalizniak, Liliana [Biotechnology and Environmental Biology, School of Applied Sciences, RMIT University, PO Box 71, Bundoora, Victoria 3083 (Australia); Dunlop, Jason E. [Department of Environment and Resource Management (DERM), 120 Meiers Rd, Indooroopilly, Queensland 4068 (Australia); Smart Water Research Facility, Griffith University, Queensland (Australia); Nugegoda, Dayanthi [Biotechnology and Environmental Biology, School of Applied Sciences, RMIT University, PO Box 71, Bundoora, Victoria 3083 (Australia); Choy, Satish C. [Department of Environment and Resource Management (DERM), 120 Meiers Rd, Indooroopilly, Queensland 4068 (Australia)

2010-02-15

The effects of suspended and deposited sediments on the macroinvertebrates are well documented in upland streams but not in slower flowing lowland rivers. Using species found in lowland lotic environments, we experimentally evaluate mechanisms for sediments to affect macroinvertebrates, and in one experiment whether salinity alters the effect of suspended sediments. Suspended kaolin clay reduced feeding of Ischnura heterosticta (Odonata: Coenagrionidae) at high turbidity (1000-1500 NTU) but had no effects on feeding of Hemianax papuensis (Odonata: Aeshnidae) and Micronecta australiensis (Hemiptera: Corixidae). In freshwater (0.1 mS/cm), survival of Ischnura aurora was poor in clear water, but improved with suspended kaolin. Growth and feeding of I. aurora were unaffected by suspended sediments and salinity. Burial (1-5 mm) of eggs with kaolin or sand reduced hatching in Physa acuta (Gastropoda: Physidae), Gyraulus tasmanica (Gastropoda: Planorbidae) and Chironomus cloacalis (Diptera: Chironomidae). Settling sediments may pose greater risk to lowland lotic invertebrates than suspended sediments. - Sediment deposition may be more directly detrimental to macroinvertebrates of lowland rivers than suspended sediments.

Heterogeneous precipitation of silver nanoparticles on kaolinite plates

International Nuclear Information System (INIS)

Cabal, B; Moya, J S; Torrecillas, R; Malpartida, F

2010-01-01

Two different methods to obtain silver nanoparticles supported on kaolin crystals have been performed: the first one followed a thermal reduction and the second one a chemical reduction. In both cases, the silver nanoparticles with two different average particles size (ca.12 and 30 nm) were perfectly isolated and attached to the surface of the kaolin plates. The silver nanoparticles were localized mainly at the edge of the single crystal plates, the hydroxyl groups being the main centres of adsorption. The samples were fully characterized by XRD, UV-vis spectroscopy and TEM. The antimicrobial benefits of the composites were evaluated as antibacterial against common Gram-positive and Gram-negative bacteria, and antifungal activity against yeast. The results indicated a high antimicrobial activity for Escherichia coli JM 110 and Micrococcus luteus, while being inactive against yeast under our experimental conditions. The chemical analysis of Ag in the fermentation broths show that only a small portion of metal (<9 ppm) is released from the kaolin/metakaolin particles. Therefore, the risk of toxicity due to a high concentration of metal in the medium is minimized.

Adhesion of metals to LaCrO3 by copper sulphide method

International Nuclear Information System (INIS)

Ebata, Yoshihiro; Toibana, Yasuo; Uetsuki, Tsuneo; Kose, Saburo; Kataoka, Nagamasa

1979-01-01

A method of adhering metallic copper to LaCrO 3 was researched using mixtures of copper sulphide and kaolin as the coponent of metalliser to obtain optimum condition for the adhesion. As a maximum adhesive strength, 300 kg/cm 2 has been attained with the metallised intermediate layer which was composed of 70 wt% copper sulphide and 30 wt% kaolin, and fired at 1000 0 C. The adhesive strength was not affected by soaking the specimen into 48% KOH solution at 70 0 C for 70 hr. Electric resistance of the desirable specimen metallised with Cu 2 S- kaolin layer and silver-paint was 1.4 times higher than that of the one coated with silver-paint only. Investigating into the fired intermediate layer by means of X-ray diffraction and EPMA, it has been confirmed that the layer partly transformed to a phase of spinel of Al 2 O 3 with CuO. Thickness of the layer penetrated into the LaCrO 3 substratum was about 50 - 60 μm. (author)

Heterogeneous precipitation of silver nanoparticles on kaolinite plates.

Science.gov (United States)

Cabal, B; Torrecillas, R; Malpartida, F; Moya, J S

2010-11-26

Two different methods to obtain silver nanoparticles supported on kaolin crystals have been performed: the first one followed a thermal reduction and the second one a chemical reduction. In both cases, the silver nanoparticles with two different average particles size (ca.12 and 30 nm) were perfectly isolated and attached to the surface of the kaolin plates. The silver nanoparticles were localized mainly at the edge of the single crystal plates, the hydroxyl groups being the main centres of adsorption. The samples were fully characterized by XRD, UV-vis spectroscopy and TEM. The antimicrobial benefits of the composites were evaluated as antibacterial against common Gram-positive and Gram-negative bacteria, and antifungal activity against yeast. The results indicated a high antimicrobial activity for Escherichia coli JM 110 and Micrococcus luteus, while being inactive against yeast under our experimental conditions. The chemical analysis of Ag in the fermentation broths show that only a small portion of metal (<9 ppm) is released from the kaolin/metakaolin particles. Therefore, the risk of toxicity due to a high concentration of metal in the medium is minimized.

Heterogeneous precipitation of silver nanoparticles on kaolinite plates

Energy Technology Data Exchange (ETDEWEB)

Cabal, B; Moya, J S [Instituto de Ciencia de Materiales de Madrid (ICMM-CSIC), 28049, Cantoblanco, Madrid (Spain); Torrecillas, R [Centro de Investigacion en Nanomateriales y NanotecnologIa (CINN), Consejo Superior de Investigaciones CientIficas (CSIC)-Universidad de Oviedo-UO-Principado de Asturias, Parque Tecnologico de Asturias, 33428, Llanera (Spain); Malpartida, F, E-mail: bcabal@icmm.csic.es [Centro Nacional de BiotecnologIa (CNB-CSIC), 28049, Cantoblanco, Madrid (Spain)

2010-11-26

Two different methods to obtain silver nanoparticles supported on kaolin crystals have been performed: the first one followed a thermal reduction and the second one a chemical reduction. In both cases, the silver nanoparticles with two different average particles size (ca.12 and 30 nm) were perfectly isolated and attached to the surface of the kaolin plates. The silver nanoparticles were localized mainly at the edge of the single crystal plates, the hydroxyl groups being the main centres of adsorption. The samples were fully characterized by XRD, UV-vis spectroscopy and TEM. The antimicrobial benefits of the composites were evaluated as antibacterial against common Gram-positive and Gram-negative bacteria, and antifungal activity against yeast. The results indicated a high antimicrobial activity for Escherichia coli JM 110 and Micrococcus luteus, while being inactive against yeast under our experimental conditions. The chemical analysis of Ag in the fermentation broths show that only a small portion of metal (<9 ppm) is released from the kaolin/metakaolin particles. Therefore, the risk of toxicity due to a high concentration of metal in the medium is minimized.

Thermal expansion of ceramic samples containing natural zeolite

Science.gov (United States)

Sunitrová, Ivana; Trník, Anton

2017-07-01

In this study the thermal expansion of ceramic samples made from natural zeolite is investigated. Samples are prepared from the two most commonly used materials in ceramic industry (kaolin and illite). The first material is Sedlec kaolin from Czech Republic, which contains more than 90 mass% of mineral kaolinite. The second one is an illitic clay from Tokaj area in Hungary, which contains about 80 mass% of mineral illite. Varying amount of the clay (0 % - 50 %) by a natural zeolite from Nižný Hrabovec (Slovak Republic), containing clinoptilolite as major mineral phase is replaced. The measurements are performed on cylindrical samples with a diameter 14 mm and a length about 35 mm by a horizontal push - rod dilatometer. Samples made from pure kaolin, illite and zeolite are also subjected to this analysis. The temperature regime consists from linear heating rate of 5 °C/min from 30 °C to 1100 °C. The results show that the relative shrinkage of ceramic samples increases with amount of zeolite in samples.

Emerging integrated nanoclay-facilitated drug delivery system for papillary thyroid cancer therapy

Science.gov (United States)

Zhang, Yi; Long, Mei; Huang, Peng; Yang, Huaming; Chang, Shi; Hu, Yuehua; Tang, Aidong; Mao, Linfeng

2016-09-01

Nanoclay can be incorporated into emerging dual functional drug delivery systems (DDSs) to promote efficiency in drug delivery and reduce the toxicity of doxorubicin (DOX) used for thyroid cancer treatment. This paper reports the expansion of the basal spacing of kaolinite nanoclay was expanded from 0.72 nm to 0.85 nm, which could provide sufficiently spacious site for hosting doxorubicin molecules and controlling the diffusion rate. A targeted design for papillary thyroid cancer cells was achieved by introducing KI, which is consumed by the sodium-iodide symporter (NIS). As indicated by MTT assays, confocal laser scanning microscopy and bio-TEM observations, methoxy-intercalated kaolinite (KaolinMeOH) exhibited negligible cytotoxicity against papillary thyroid cancer cells. By contrast, DOX-KaolinMeOH showed dose-dependent therapeutic effects in vitro, and KI@DOX-KaolinMeOH was found to act as a powerful targeted therapeutic drug. Furthermore, active and passive targeting strategies played a role in the accumulation of the drug molecules, as verified by an in vivo bio-distribution analysis.

Magnetic separation for soil decontamination

International Nuclear Information System (INIS)

Avens, L.R.; Worl, L.A.; deAguero, K.J.; Padilla, D.D.; Prenger, F.C.; Stewart, W.F.; Hill, D.D.; Tolt, T.L.

1993-01-01

High gradient magnetic separation (HGMS) is a physical separation process that is used to extract magnetic particles from mixtures. The technology is used on a large scale in the kaolin clay industry to whiten or brighten kaolin clay and increase its value. Because all uranium and plutonium compounds are slightly magnetic, HGMS can be used to separate these contaminants from non-magnetic soils. A Cooperative Research and Development Agreement (CRADA) was signed in 1992 between Los Alamos National Laboratory (LANL) and Lockheed Environmental Systems and Technologies Company (LESAT) to develop HGMS for soil decontamination. This paper reports progress and describes the HGMS technology

Removal of Pb(II) from aqueous solution using modified and unmodified kaolinite clay

International Nuclear Information System (INIS)

Jiang Mingqin; Wang Qingping; Jin Xiaoying; Chen Zuliang

2009-01-01

Modified kaolinite clay with 25% (w/w) aluminium sulphate and unmodified kaolin were investigated as adsorbents to remove Pb(II) from aqueous solution. The results show that amount of Pb(II) adsorbed onto modified kaolin (20 mg/g) was more than 4.5-fold than that adsorbed onto unmodified kaolin (4.2 mg/g) under the optimized condition. In addition, the linear Langmuir and Freundlich models were used to describe equilibrium isotherm. It is observed that the data from both adsorbents fitted well to the Langmuir isotherm. The kinetic adsorption of modified and unmodified kaolinite clay fitted well to the pseudo-second-order model. Furthermore, both modified and unmodified kaolinite clay were characterized by X-ray diffraction, Fourier transform infrared (FT-IR) and scanning electron microscope (SEM). Finally, both modified and unmodified kaolinite clay were used to remove metal ions from real wastewater, and results show that higher amount of Pb(II) (the concentration reduced from 178 to 27.5 mg/L) and other metal ions were removed by modified kaolinite clay compared with using unmodified adsorbent (the concentration reduced from 178 to 168 mg/L).

Enhanced Coagulation Efficiency of Moringa Oleifera Seeds Through Selective Oil Extraction

Directory of Open Access Journals (Sweden)

Suleyman A. Muyibi

2012-10-01

Full Text Available In this laboratory based study, varying quantities of oil, corresponding to 20 % w/w, 25 % w/w and 30 % w/w kernel weight extracted from Moringa oleifera seeds ( S1, S2, S3 respectively  were applied in the coagulation of model turbid water (kaolin suspension and turbid river water samples from River Batang Kali and River Selangor in Malaysia to determine the percentage oil removed which gave the best coagulation efficiency. For model turbid water (kaolin suspension coagulation of low turbidity of 35 NTU, medium turbidity of 100 NTU and high turbidity of 300 NTU, sample S2  gave the best turbidity removal corresponding to 91.7%, 95.5% and 99% respectively. Application of sample S2 to River Batang Kali with low initial turbidity of 32 NTU and high initial turbidity of 502 NTU gave a highest turbidity removal of 69% and 99% respectively. Application to River Selangor with medium initial turbidity- of 87 NTU and high initial turbidity of 466 NTU gave a highest residual turbidity' of 94% and 98.9%,  respectively.Key words: Moringa oleifera seed, selective oil extraction, coagulation, model turbid water (kaolin suspension, river water, turbidity removal.

Antimicrobial material obtained from pulping white paper waste

International Nuclear Information System (INIS)

Angioletto, E.; Fiori, M.A.; Pitch, C.T.; Mendes, E.; Oliveira, C.M.; Melo, C.R.; Riella, H.G.

2011-01-01

The paper industry produces white waste, consisting of 45% kaolin, 45% calcium carbonate and 10% cellulose. After calcination at 903K for two hours, the cellulose is burnt and decomposed kaolin in metakaolin. Held treatment of the calcined material with hydrochloric acid to remove calcium carbonate. The metakaolin is treated with sodium hydroxide solution to obtain the type of zeolite 4A. The zeolites were characterized using XRD, XRF and SEM. The zeolite was subjected to ion exchange with zinc sulphate and silver nitrate at room temperature, stirring, for six hours. This material was tested with Staphylococcus aureus and Escherichia coli, to get excellent results with regard to bactericidal properties.(author)

The Effects of Natural and Anthropogenic Microparticles on Individual Fitness in Daphnia magna.

Directory of Open Access Journals (Sweden)

Martin Ogonowski

Full Text Available Concerns are being raised that microplastic pollution can have detrimental effects on the feeding of aquatic invertebrates, including zooplankton. Both small plastic fragments (microplastics, MPs produced by degradation of larger plastic waste (secondary MPs; SMPs and microscopic plastic spheres used in cosmetic products and industry (primary MPs; PMPs are ubiquitously present in the environment. However, despite the fact that most environmental MPs consist of weathered plastic debris with irregular shape and broad size distribution, experimental studies of organism responses to MP exposure have largely used uniformly sized spherical PMPs. Therefore, effects observed for PMPs in such experiments may not be representative for MP-effects in situ. Moreover, invertebrate filter-feeders are generally well adapted to the presence of refractory material in seston, which questions the potential of MPs at environmentally relevant concentrations to measurably affect digestion in these organisms. Here, we compared responses to MPs (PMPs and SMPs and naturally occurring particles (kaolin clay using the cladoceran Daphnia magna as a model organism. We manipulated food levels (0.4 and 9 μg C mL-1 and MP or kaolin contribution to the feeding suspension (<1 to 74% and evaluated effects of MPs and kaolin on food uptake, growth, reproductive capacity of the daphnids, and maternal effects on offspring survival and feeding. Exposure to SMPs caused elevated mortality, increased inter-brood period and decreased reproduction albeit only at high MP levels in the feeding suspension (74% by particle count. No such effects were observed in either PMP or kaolin treatments. In daphnids exposed to any particle type at the low algal concentration, individual growth decreased by ~15%. By contrast, positive growth response to all particle types was observed at the high algal concentration with 17%, 54% and 40% increase for kaolin, PMP and SMP, respectively. When test particles

Behavior of sodium chloride during the combustion of carbon

Energy Technology Data Exchange (ETDEWEB)

Brinsmead, K H; Kear, R W

1956-01-01

The effects of combustion time, temperature, atmosphere, and the presence of other minerals on the release of Na and Cl from carbon that contained varying amounts of NaCl were examined. Initial testing consisted of adding 0.25, 12.7 and 2.54% NaCl to carbon, and pelletizing and burning the carbon for an hour at the following temperatures: 700, 800, 900, and 1000/sup 0/C. Pellets containing 1.27% NaCl were also burned at 400, 500, and 600/sup 0/C. Additional testing involved the combustion of pellets in dry nitrogen, dry air, moist nitrogen, moist air, and adding various amounts of kaolin to the carbon prior to pelletizing. The testing program demonstrated the following: in all tests the percentage of Na and Cl released increased as the temperature and the salt content increased; generally more Cl was released than Na, particularly at temperatures between 600 to 900 degrees; the release of Na and Cl was significantly less in an atmosphere of N, particularly at lower temperatures; the water vapor present in the moist air seemed to hinder the release of Na but increased the amount of Cl released; a reduction in the amount of Na but not the amount of Cl released was noticed when kaolin was added. The following was concluded from the test results: since Na and Cl were released at different rates there seems to be more than a physical volatization involved; water vapor in the air could affect the amount of Na and Clreleased by lowering the combustion temperature of the carbon, thereby allowing the Na and Cl to react with the water present to form NaOH and HC1; and the reduction in the amount of Na released when kaolin was added was a result of Na reacting with kaolin to form an insoluble silicate.

Synthesis, characterization and flocculation activity of novel Fe(OH){sub 3}-polyacrylamide hybrid polymer

Energy Technology Data Exchange (ETDEWEB)

Wang Huilong; Cui Jinyan [Department of Chemistry, Dalian University of Technology, Dalian 116023 (China); Jiang Wenfeng, E-mail: dlutjiangwf@yahoo.com.cn [Department of Chemistry, Dalian University of Technology, Dalian 116023 (China)

2011-11-01

Highlights: {yields} The preparation of a novel Fe(OH){sub 3}-PAM hybrid polymer flocculant is achieved via free radical solution polymerization. {yields} Flocculation of kaolin suspensions using this novel Fe(OH){sub 3}-PAM hybrid polymer flocculant is revealed in this study. {yields} The statistical model was first applied for calculating the thermodynamic parameters for the kaolin flocculating process. - Abstract: A novel Fe(OH){sub 3}-polyacrylamide inorganic-organic hybrid polymer (FHPAM) was synthesized via free radical solution polymerization initiated by a redox initiation system ((NH{sub 4}){sub 2}S{sub 2}O{sub 8}-NaHSO{sub 3}) in an aqueous medium. Reaction parameters influencing the intrinsic viscosity and the yield of the hybrid polymer, such as initiator concentration, monomer mass fraction, temperature and reaction time were investigated and optimized. The results show that the maximum intrinsic viscosity and up to 94% yields of the hybrid polymer can be achieved using initiator concentration of 0.3% with acrylamide monomer mass fraction of 20% under solution polymerization at 40 deg. C for 7 h. The physicochemical properties of this hybrid flocculant were characterized with TEM, FTIR spectra, TGA, and conductivity. It was found that a chemical bond exists between Fe(OH){sub 3} colloid and polyacrylamide chains in the FHPAM. The application of the hybrid polymer for the treatment of 2.5 g L{sup -1} kaolin suspension indicates that it had an excellent flocculation capacity and its flocculation efficiency was much better than that of commercial available polyacrylamide (PAM) and polymeric ferric sulfate (PFS). The optimal conditions for the flocculation treatment of kaolin suspension were the FHPAM dosage of 40 mg L{sup -1} at pH 7.0. The thermodynamic parameters for the flocculation process were calculated based on a statistical model. Interpretation of the results was given.

Synthesis, characterization and flocculation activity of novel Fe(OH)3-polyacrylamide hybrid polymer

International Nuclear Information System (INIS)

Wang Huilong; Cui Jinyan; Jiang Wenfeng

2011-01-01

Highlights: → The preparation of a novel Fe(OH) 3 -PAM hybrid polymer flocculant is achieved via free radical solution polymerization. → Flocculation of kaolin suspensions using this novel Fe(OH) 3 -PAM hybrid polymer flocculant is revealed in this study. → The statistical model was first applied for calculating the thermodynamic parameters for the kaolin flocculating process. - Abstract: A novel Fe(OH) 3 -polyacrylamide inorganic-organic hybrid polymer (FHPAM) was synthesized via free radical solution polymerization initiated by a redox initiation system ((NH 4 ) 2 S 2 O 8 -NaHSO 3 ) in an aqueous medium. Reaction parameters influencing the intrinsic viscosity and the yield of the hybrid polymer, such as initiator concentration, monomer mass fraction, temperature and reaction time were investigated and optimized. The results show that the maximum intrinsic viscosity and up to 94% yields of the hybrid polymer can be achieved using initiator concentration of 0.3% with acrylamide monomer mass fraction of 20% under solution polymerization at 40 deg. C for 7 h. The physicochemical properties of this hybrid flocculant were characterized with TEM, FTIR spectra, TGA, and conductivity. It was found that a chemical bond exists between Fe(OH) 3 colloid and polyacrylamide chains in the FHPAM. The application of the hybrid polymer for the treatment of 2.5 g L -1 kaolin suspension indicates that it had an excellent flocculation capacity and its flocculation efficiency was much better than that of commercial available polyacrylamide (PAM) and polymeric ferric sulfate (PFS). The optimal conditions for the flocculation treatment of kaolin suspension were the FHPAM dosage of 40 mg L -1 at pH 7.0. The thermodynamic parameters for the flocculation process were calculated based on a statistical model. Interpretation of the results was given.

Basic research on the development of 'intelligent-type' humidity control materials; Intelligent gata choshitsu zairyo no kaihatsu ni kansuru kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tomura, S.; Maeda, M.; Inukai, K.; Ohashi, F.; Suzuki, M.; Suzuki, K.; Shibasaki, Y. [National Industrial Research Institute of Nagoya,Nagoya (Japan)

2000-10-25

The water vapor adsorption desorption isotherms of purified and/or synthesized sepiolite, allophane, diatomite, selectively leached kaolin and mesoporous silica were measured to develop humidity control materials in living environments. Based on Kelvin's capillary condensation theory, suitable pore diameters for controlling relative humidity at 40 and 70% were calculated to be 3.2 and 7.4 nm, respectively. Wakkanai diatomite, purified allophane, selectively leached kaolin and mesoporous silica have suitable pore diameters and high water adsorptivity, and were considered as candidates for humidity self-control materials. Among these materials, mesoporous silica formed as a tile showed the best performance as a humidity control material in desiccator and model house levels. (author)

Correlation between thromboelastography and traditional coagulation test parameters in hospitalized dogs

Directory of Open Access Journals (Sweden)

Rubanick JV

2017-02-01

Full Text Available Jean V Rubanick, Medora B Pashmakova, Micah A Bishop, James W Barr Department of Veterinary Small Animal Clinical Sciences, Texas A&M University, College Station, TX, USA Abstract: A hospital-based, prospective cross-sectional study was used to compare kaolin-activated thromboelastography (TEG parameters with traditional coagulation tests in 29 hospitalized dogs. Cases were included if the attending clinician requested coagulation testing. Blood was obtained from each dog and coagulation (prothrombin time, partial thromboplastin time, antithrombin activity, d-dimer concentration, and fibrinogen concentration and TEG analyses were performed. Hematocrit (Hct was also measured. Traditional coagulation results were evaluated for correlation with those from kaolin-activated TEG. Spearman’s correlation was used to calculate correlation coefficients. Fibrinogen was positively correlated with maximum amplitude (Pearson r=0.72, P<0.001 and global clot strength (Pearson r=0.72, P<0.001. There was no correlation between any of the remaining coagulation variables, TEG parameters, or Hct. Results of kaolin-activated TEG and traditional coagulation tests are not interchangeable means of monitoring coagulation derangements in this intensive care unit patient population. Determination of a true outcome measure is necessary to establish TEG’s clinical relevance to veterinary medicine. Keywords: TEG, thromboelastography, coagulation, hemostasis

Effect of gamma irradiation, evaporation retardants and transpiration suppressants on grain yield, nutrient uptake and moisture-use efficiency on bread wheat (Triticum aestivum)

International Nuclear Information System (INIS)

Dash, D.K.; Sen, Avijit; Misra, N.M.

1988-01-01

A field trial was conducted on 'Malaviya 37' bread wheat (Triticum aestivum Linn. emend. Fiori and Paol.) in 1982-83 and 1983-84. It included 4 dos es of gamma irradiation of seeds (0, 2.5, 4.5 and 6.5 kR) and 5 treatments of evaporation retardants and transpiration suppressants, viz. control, rice (Oryza sativa Linn.) straw, wheat straw, rice straw + phenyl mercuric acetate (150 ppm) and wheat straw + kaolin (6 per cent). Seed irradiation with gamma-rays at 6.5 kR and wheat straw + kaolin gave 11.76 and 61.37 per cent higher yield than the control respectively. For moisture-use efficiency and NPK uptake these treatments also showed the same trend. (author). 12 refs

Revealing the characteristics of a novel bioflocculant and its flocculation performance in Microcystis aeruginosa removal

Science.gov (United States)

Sun, Pengfei; Hui, Cai; Bai, Naling; Yang, Shengmao; Wan, Li; Zhang, Qichun; Zhao, Yuhua

2015-12-01

In the present work, a novel bioflocculant, EPS-1, was prepared and used to flocculate the kaolin suspension and Microcystis aeruginosa. We focused on the characteristics and flocculation performance of EPS-1, especially with regard to its protein components. An important attribute of EPS-1 was its protein content, with 18 protein types identified that occupied a total content of 31.70% in the EPS-1. Moreover, the flocculating activity of these protein components was estimated to be no less than 33.93%. Additionally, polysaccharides that occupied 57.12% of the total EPS-1 content consisted of four monosaccharides: maltose, D-xylose, mannose, and D-fructose. In addition, carbonyl, amino, and hydroxyl groups were identified as the main functional groups. Three main elements, namely C1s, N1s, and O1s, were present in EPS-1 with relative atomic percentages of 62.63%, 24.91%, and 10.5%, respectively. Zeta potential analysis indicated that charge neutralization contributed to kaolin flocculation, but was not involved in M. aeruginosa flocculation. The flocculation conditions of EPS-1 were optimized, and the maximum flocculating efficiencies were 93.34% within 2 min for kaolin suspension and 87.98% within 10 min for M. aeruginosa. These results suggest that EPS-1 could be an alternative to chemical flocculants for treating wastewaters and cyanobacterium-polluted freshwater.

Density, Viability Conidia And Symptoms of Metarhizium anisopliae infection on Oryctes rhinoceros larvae

Science.gov (United States)

Indriyanti, D. R.; Putri, R. I. P.; Widiyaningrum, P.; Herlina, L.

2017-04-01

M. anisopliae is parasitic fungus on insect pests; it is used as a biocontrol agent. M. anisopliae can be propagated on maize or rice substrate. M. anisopliae is currently sold in the form of kaolin powder formulations. Before it is used to check the density, viability and pathogenicity of M. anisopliae. However the problem is the kaolin powder very soft, so it difficult to distinguish between kaolin and conidia. This article gives information on how to calculate conidia density, viability and symptoms of M. anisopliae infection on Oryctes rhinoceros larvae. The study was conducted in the laboratory to determine the density and viability. The pathogenicity testing was done using pots. The Pot is containing soil substrate mixed with M. Anispoliae and ten tails O. Rhinoceros larvae per pot. The results showed that the density of M. anisopliae conidia was 1.81 x 108 conidia mL-1 and the viability was 94% within 24 hours. The larval mortality began to emerge in the 1st week, and all larvae died at the sixth week. The symptom of M. anisopliae infection on Oryctes rhinoceros larvae, there was a black spot on the larval integument. The larvae movements become slow and poor appetite; it will die within 3-7 days. The larvae die hard, and the white hyphae grow on the body surface that turns green.

Synthesis and characterization of JBW structure and its thermal transformation

International Nuclear Information System (INIS)

Hegazy, Eman Z.; Kosa, Samia A.; Abd El Maksod, Islam Hamdy

2012-01-01

In this paper, JBW zeolite prepared from Egyptian kaolin was investigated by means of XRD, IR, SEM, EDX and ion exchange of some heavy metals. Adsorption isotherms were used to investigate the structure and properties of the prepared zeolite. XRD analysis showed that the JBW was a pure crystalline phase with orthorhombic crystal symmetry. Thermal treatment showed that the JBW transformed into the It-Carn phase at 1000 °C through an intermediate crystalline alumino silicate phase. SEM images showed that the JBW crystallised in a cylindrical shape. However, spherical agglomerates were observed at lower magnifications. The ion exchange isotherms with Cu 2+ , Ni 2+ and Co 2+ were found to follow a Freundlich isotherm. In addition, it shows higher affinity towards Cu 2+ than other ions. - Graphical abstract: JBW zeolite structure was prepared from Egyptian kaolin and characterised. XRD analysis showed that the JBW was a pure crystalline phase with orthorhombic crystal symmetry. Thermal treatment showed that the JBW transformed into the It-Carn phase at 1000 °C through an intermediate crystalline alumino silicate phase. Highlights: ► Egyptian kaolin was successfully used to prepare pure phase of JBW Structure. ► JBW is stable till 2+ , Ni 2+ , and Co 2+ followed up Freundlich isotherm. ► Selectivity towards Cu 2+ is much higher than Co 2+ or Ni 2+ .

Development of alumino-silicate refractories in Ghana

International Nuclear Information System (INIS)

Kisiedu, A. K.; Tetteh, D.M.B.; Obiri, H. A.; Brenya, E. F.; Ayensu, A.

2008-01-01

Alumino-silicate (bauxite), andalusite, kaolin and clay were investigated for suitability in production of alumina, mullite and fireclay brick refractories. The raw materials were characterized by X-ray diffraction, differential thermal and silicate analyses. The x-ray diffraction analysis of alumina and mullite refractories fired at 1450 0 C, and fireclay bricks fired at 1350 0 C, indicated presence of corundum and alpha-alumina crystals. The values of thermal (fired) shrinkage, crushing, strength, porosity, water absorption and bulk density determined were 31.1%, 2.3 x 10 3 kg/m 3 , 4.86 x 10 6 N/m 2 and 13.2 % for mullite; 30.2%, 2.4 x 10 3 kg/m 3 , 3.20 x 10 6 N/m 2 and W = 12.8 % for alumina; and 25.2 %, 2.1 x 10 3 kg/m 3 , 2.61 x 10 6 N/m 2 and W = 11.8% for fireclay, respectively. Bauxite, andalusite and special kaolin were identified as potential raw materials for developing alumina and mullite refractories for construction of high temperature kilns and furnaces operating at 1350 0 C. The clay and kaolin minerals could be used to produce fireclay refractories for construction of incinerators operating at maximum temperatures of about 1000 0 C. The performance of the refractories was demonstrated by producing bricks to construct kilns and incinerators for the ceramic industry and hospitals. (au)

Radiation-induced defects in clay minerals, markers of the mobility of the uranium in solution in the unconformity-type uranium deposits

International Nuclear Information System (INIS)

Morichon, E.

2008-10-01

This study presents the works driven on three groups of clay minerals (kaolins, illite, sudoite (di-tri-octahedral chlorites)) characteristics of the alteration halos surrounding unconformity-type uranium deposits, in order to reveal uranium paleo-circulations in the intra-cratonic meso-Proterozoic basins (1,2 - 1,6 Ga). Thanks to Electron Paramagnetic Resonance Spectroscopy (EPR), we were able to highlight the persistence of structural defects in kaolin-group minerals contemporaneous of the basin diagenesis, and demonstrate the existence of relatively stable defects in illites and sudoites contemporaneous of the uranium deposits setting. Thus, the main defect in illite (Ai centre) and the main defect in sudoite (As centre) are characterized by their g components such as, respectively, gt = 2,003 et g// = 2,051 for illite and gt = 2,008 et g// = 2,051 for sudoite. As the main defect in kaolins (kaolinite/dickite), the main defects in illite and sudoite are perpendicularly oriented according to the (ab) plane, on the tetrahedral Si-O bound. However, their thermal stabilities seem different. The observation of samples from different zones (background, anomal or mineralized) of the Athabasca basin (Canada) allowed to identify a parallel evolution between actual defects concentration measured in the different clay minerals and the proximity of the mineralisation zones. Consequently, clays minerals can be considered as potential plotters of zones where uranium-rich solutions have circulated. (author)

Broadband electromagnetic analysis of compacted kaolin

International Nuclear Information System (INIS)

Bore, Thierry; Scheuermann, Alexander; Wagner, Norman; Cai, Caifang

2017-01-01

The mechanical compaction of soil influences not only the mechanical strength and compressibility but also the hydraulic behavior in terms of hydraulic conductivity and soil suction. At the same time, electric and dielectric parameters are increasingly used to characterize soil and to relate them with mechanic and hydraulic parameters. In the presented study electromagnetic soil properties and suction were measured under defined conditions of standardized compaction tests. The impact of external mechanical stress conditions of nearly pure kaolinite was analyzed on soil suction and broadband electromagnetic soil properties. An experimental procedure was developed and validated to simultaneously determine mechanical, hydraulic and broadband (1 MHz–3 GHz) electromagnetic properties of the porous material. The frequency dependent electromagnetic properties were modeled with a classical mixture equation (advanced Lichtenecker and Rother model, ALRM) and a hydraulic-mechanical-electromagnetic coupling approach was introduced considering water saturation, soil structure (bulk density, porosity), soil suction (pore size distribution, water sorption) as well as electrical conductivity of the aqueous pore solution. Moreover, the relaxation behavior was analyzed with a generalized fractional relaxation model concerning a high-frequency water process and two interface processes extended with an apparent direct current conductivity contribution. The different modeling approaches provide a satisfactory agreement with experimental data for the real part. These results show the potential of broadband electromagnetic approaches for quantitative estimation of the hydraulic state of the soil during densification. (paper)

INTEGRATING CASSAVA VARIETIES AND Typhlodramulus aripo ...

African Journals Online (AJOL)

ACSS

The objective of this study was to identify cassava ... mite species, of Colombian and Brazilian origin, ... Typhlodramulus aripo was imported by the ..... Environmental Entomology 36:938-951 ... shade, weed competition, and kaolin in particle.

Instrumental neutron activation analysis (INAA) of some clayey rocks of Poland

International Nuclear Information System (INIS)

Janczyszyn, J.; Domanska, G.; Wyszomirski, P.

1988-01-01

The instrumental neutron activation analysis (INAA) was applied for determination of minor and trace element contents in some Polish clayey rocks. Lower Silesian kaolins from Wyszonowice near Strzelin and from Wadroze Wielkie near Legnica as well as allite from Kaplonosy (Lublin Coal Basin) were investigated. The contents of 26 elements were determined, including rare earth metals (Sc, La, Ce, Nd, Sm, Eu, Tb, Yb, Lu), actinides (U, Th), alkali metals (Na, K, Rb, Cs) and gold. INAA studies allowed to determine the variability of minor and trace element contents in the weathering profile in 2,5/K borehole in Wyszonowice and in size fractions separated from kaolin of Wadroze Wielkie. When using this method, the effectiveness of chemical and thermal extraction of these elements from allite of Kaplonosy was checked, too. (author)

93 - 100_Yakubu

African Journals Online (AJOL)

DR. AMINU

Dange/Wurno and Gundumi formation on kalambaina, Adarawa, Bissalam and Tureta ... dominant mineral identified in the soils is quartz with kaolinite, feldspar and chlorite in trace ... broken down finally to kaoline or hydroxides and oxide.

75 FR 29364 - Certain Coated Paper Suitable for High-Quality Print Graphics Using Sheet-Fed Presses From China...

Science.gov (United States)

2010-05-25

... sheet-fed presses; coated on one or both sides with kaolin (China or other clay), calcium carbonate... of 80 or higher; weighing not more than 340 grams per square meter; whether gloss grade, satin grade...

PRINCIPAL COMPONENT ANALYSIS TO EVALUATE THE SPATIAL ...

African Journals Online (AJOL)

B. S. Chandravanshi

class ... features with those of the original data attributes. ... applications will depend on how clay and data scientists keep track, synchronise and .... The chemical compositions of the kaolin samples were determined using X-ray fluorescence.

the study of thermal effect on the surface properties of gamma ...

African Journals Online (AJOL)

eobe

excellent properties such as highly uniform channels, large surface area and narrow pore size distribution. It has been widely used as adsorbents, ... important material that can be prepared from bauxite or kaolin in several different phases.

PERFORMANCE EVALUATION OF CERAMICS MICROFILTRATION MEMBRANE FOR WATER TREATMENT

Directory of Open Access Journals (Sweden)

F.T. Owoeye

2016-05-01

Full Text Available Ceramic membranes are especially suitable for processes with high temperatures and harsh chemical environments or for processes where sterilizability of the membrane is important. The main objective of this work is to determine the evaluation of four different ceramic membranes with different material compositions. Ceramic disc type microfiltration membranes were fabricated by the mould and press method from different percentage compositions of clay, kaolin, sawdust and wood charcoal. The fabricated membranes were sintered at a temperature of 1100°C and characterized by an X-ray diffractometer and optical scanner. Compressibility tests and physical properties of the membranes were also examined. It was observed that, as the percentage composition of kaolin increased from 0 to 80% and the percentage composition of clay decreased from 80 to 0% respectively, the compressive stress of all the sample membranes increased, with an increase in compressive strain from 1.8 to 2.4. Sample A had the highest value of compressive stress from 1.8 to 2.2 compressive strain, but sample B had the highest value of compressive stress of 150MPa at a compressive strain of 2.4. Optical micrographs of all membranes showed the presence of uniformly distributed pores and no cracks were seen around them. It was concluded that, with increasing percentage of kaolin and decreasing percentage of clay, there was a decrease in porosity and water absorption, as well as a decrease in the mechanical properties of the fabricated membranes.

Preparation and Properties of a Novel Semi-IPN Slow-Release Fertilizer with the Function of Water Retention.

Science.gov (United States)

Xiang, Yang; Ru, Xudong; Shi, Jinguo; Song, Jiang; Zhao, Haidong; Liu, Yaqing; Guo, Dongdong; Lu, Xin

2017-12-20

A new semi-interpenetrating polymer network (semi-IPN) slow-release fertilizer (SISRF) with water absorbency, based on the kaolin-g-poly(acrylic acid-co-acrylic amide) (kaolin-g-P(AA-co-AM)) network and linear urea-formaldehyde oligomers (UF), was prepared by solution polymerization. Nutrients phosphorus and potassium were supplied by adding dipotassium hydrogen phosphate during the preparation process. The structure and properties of SISRF were characterized by various characterization methods. SISRF showed excellent water absorbency of 68 g g -1 in tap water. The slow-release behavior of nutrients and water-retention capacity of SISRF were also measured. Meanwhile, the swelling kinetics was well described by a pseudo-second-order kinetics model. Results suggested the formation of SISRF with simultaneously good slow-release and water-retention capacity, which was expected to apply in modern agriculture and horticulture.

Model study of acid rain effect on adsorption of trace elements on soils using a multitracer

International Nuclear Information System (INIS)

Wang, H.F.; Ambe, S.; Takematsu, N.; Ambe, F.

1998-01-01

Using a radioactive multitracer and model acid rain (HCl or H 2 SO 4 solution), batch experiments were performed to examine the pH effect on the adsorption-desorption equilibrium of 16 elements on soils as a model study of an acid rain effect. Kaolin, black soil (original and with organic matter almost removed) and Kureha soil (original and with organic matter almost removed) were used as adsorbents. Characteristic dependence on the pH value of the suspension was observed for the adsorption of the elements on kaolin and the soils. The results of this model study indicate that acid rain decreases the retention of cations, while it increases or does not change the adsorption of anions on soils. Organic matter in soils has a positive effect on the extent of adsorption of most elements investigated. (author)

Low hemorrhage-related mortality in trauma patients in a Level I trauma center employing transfusion packages and early thromboelastography-directed hemostatic resuscitation with plasma and platelets

DEFF Research Database (Denmark)

Johansson, Pär I; Sørensen, Anne Marie Møller; Larsen, Claus F

2013-01-01

(ISS), transfusion therapy, and mortality were registered. Hemostatic resuscitation was based on a massive transfusion protocol encompassing transfusion packages and thromboelastography (TEG)-guided therapy. RESULTS: A total of 182 patients were included (75% males, median age 43 years, ISS of 17, 92....... Nonsurvivors had lower clot strength by kaolin-activated TEG and TEG functional fibrinogen and lower kaolin-tissue factor-activated TEG α-angle and lysis after 30 minutes compared to survivors. None of the TEG variables were independent predictors of massive transfusion or mortality. CONCLUSION: Three......-fourths of the patients transfused with plasma or PLTs within 24 hours received these in the first 2 hours. Hemorrhage caused 14% of the deaths. We introduced transfusion packages and early TEG-directed hemostatic resuscitation at our hospital 10 years ago and this may have contributed to reducing hemorrhagic trauma...

Preparation and characterization of photoactive composite kaolinite/TiO2

International Nuclear Information System (INIS)

Mamulova Kutlakova, K.; Tokarsky, J.; Kovar, P.; Vojteskova, S.; Kovarova, A.; Smetana, B.; Kukutschova, J.; Capkova, P.; Matejka, V.

2011-01-01

Preparation of nanocomposite kaolinite/TiO 2 , using hydrolysis of titanyl sulfate in the presence of kaolin was addressed. A variable (kaolin)/(titanyl sulfate) ratio has been used in order to achieve the desired TiO 2 content in prepared nanocomposites. Calcination of the composites at 600 deg, C led to the transformation of the kaolinite to metakaolinite and to origination of metakaolinite/TiO 2 composites. The prepared samples were investigated using X-ray fluorescence spectroscopy, X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetry and diffuse reflectance spectroscopy in the UV-VIS region. Structural ordering of TiO 2 on the kaolinite particle surface was modeled using empirical force field atomistic simulations in the Material Studio modeling environment. Photodegradation activity of the composites prepared was evaluated by the discoloration of Acid Orange 7 aqueous solution.

49 The Geology and Mineralogy of Clay Occurrences Around Kutigi ...

African Journals Online (AJOL)

`123456789jkl''''#

The above results and an earlier geochemical analysis suggest that it can be utilized in .... His chemical analysis show the high dominance of SiO2 ... mortar and pestle, the sample was pulverized .... Economic Evaluation of the Kaolin Deposits.

Immobilization of catalase via adsorption into natural and modified ...

African Journals Online (AJOL)

STORAGESEVER

2009-06-03

Jun 3, 2009 ... and modified active carbon obtained from walnut in various methods ... area of food technology. In this industrial ... The amount of the enzyme activity adsorbed on the clay was calculated as ..... Application of natural kaolin as ...

Author Details

African Journals Online (AJOL)

Dagwa, IM. Vol 34, No 4 (2015) - Chemical, Industrial, Materials, Mechanical, Metallurgical, Petroleum & Production Engineering Tensile and Hardness Property Evaluation of Kaolin- Sisal Fibre- Epoxy Composite Abstract PDF · Vol 35, No 1 (2016) - Chemical, Industrial, Materials, Mechanical, Metallurgical, Petroleum ...

Cone Penetrometer N Factor Determination Testing Results

Energy Technology Data Exchange (ETDEWEB)

Follett, Jordan R.

2014-03-05

This document contains the results of testing activities to determine the empirical 'N Factor' for the cone penetrometer in kaolin clay simulant. The N Factor is used to releate resistance measurements taken with the cone penetrometer to shear strength.

Composition comprising lignin and antidi arrheal component

DEFF Research Database (Denmark)

2008-01-01

The present invention relates to a composition comprising lignin and at least one compound selected from the group consisting of bromelain, papain, tannin, carvacrol, thymol, alliin, allicin, fenugreek seed, egg, poppy, poppy seeds, humic acid, roots, kaolin, catechu, cellulase, flavonoid...

structural behavior of metakaolin infused concrete structure

African Journals Online (AJOL)

user

to ions with improved durability properties [3]. In a recent ... The Kaolin sample shown in Plate 1 was ground to powder using a ... angular in shape well graded, clean, free from surface dirt and .... Figure 2: Flexural strength results of samples.

Mineralogy and chemical composition and distribution of rare earth elements of clay-rich sediments, Central Uganda

International Nuclear Information System (INIS)

Nyakairu, G.W.A.

2001-02-01

of the Buganda-Toro System rocks, whereas the felsic sediments are derivatives of granitoid rocks of the basement. The most significant geochemical finding is that despite intense weathering, which has affected most elements, the REE, Th, and Sc remain immobile. Analysis of the > 63, 32-63, and 63 μm are quartz rich. The whole-rock chemistry shows that the 2 , Al 2 O 3 , and Fe 2 O 3 compared to Upper Continental Crust (UCC) with the trace element content comparable to the bulk samples. The chondrite-normalized REE distribution patterns are remarkably similar for the grain size fractions, with a general enrichment of LREE and a depletion of Eu. The > 63 μm fractions have the lowest REE abundances and show no LREE-HREE fractionation with a negative Eu anomaly. The shape of the REE pattern of 2 and Al 2 O 3 , with the other oxides being present only in trace amounts. Depletion in oxides of Ti, Fe, Mn, Mg, Ca, Na, and K not only shows the extent of kaolinization, but also gives the kaolin an almost white color. The kaolinization and weathering processes have enriched Ni and depleted other trace element contents in the Buwambo kaolin. The chondrite normalized REE patterns show LREE enrichment with a negative Ce anomaly. The enrichment and depletion of the different trace elements appear to be caused by differentiation processes during kaolinization and leaching with meteoric water. From its mineralogical and chemical composition, the kaolin is suitable for earthen and sanitary ware production. (author)

Fragmentation of Protein Kinase N (PKN) in the Hydrocephalic Rat Brain

International Nuclear Information System (INIS)

Okii, Norifumi; Amano, Taku; Seki, Takahiro; Matsubayashi, Hiroaki; Mukai, Hideyuki; Ono, Yoshitaka; Kurisu, Kaoru; Sakai, Norio

2007-01-01

PKN (protein kinase N; also called protein kinase C-related kinase (PRK-1)), is a serine/threonine protein kinase that is ubiquitously expressed in several organs, including the brain. PKN has a molecular mass of 120 kDa and has two domains, a regulatory and a catalytic domain, in its amino-terminals and carboxyl-terminus, respectively. Although the role of PKN has not been fully elucidated, previous studies have revealed that PKN is cleaved to a constitutively active catalytic fragment of 55 kDa in response to apoptotic signals. Hydrocephalus is a pathological condition caused by insufficient cerebrospinal fluid (CSF) circulation and subsequent excess of CSF in the brain. In this study, in order to elucidate the role of PKN in the pathophysiology of hydrocephalus, we examined PKN fragmentation in hydrocephalic model rats. Hydrocephalus was induced in rats by injecting kaolin into the cisterna magna. Kaolin-induced rats (n=60) were divided into three groups according to the observation period after treatment (group 1: 3–6 weeks, group 2: 7–12 weeks, and group 3: 13–18 weeks). Sham-treated control rats, injected with sterile saline (n=20), were similarly divided into three groups. Spatial learning ability was estimated by a modified water maze test. Thereafter, brains were cut into slices and ventricular dilatation was estimated. Fragmentation of PKN was observed by Western blotting in samples collected from the parietal cortex, striatum, septal nucleus, hippocampus, and periaqueductal gray matter. All kaolin-induced rats showed ventricular dilatation. Most of them showed less spatial learning ability than those of sham-treated controls. In most regions, fragmentation of PKN had occurred in a biphasic manner more frequently than that in controls. The appearance of PKN fragmentation in periaqueductal gray matter was correlated with the extent of ventricular dilation and spatial learning disability. These results revealed that PKN fragmentation was observed in

A molecular investigation of adsorption onto mineral pigments

Science.gov (United States)

Ninness, Brian J.

Pigment suspensions are important in several processes such as ceramics, paints, inks, and coatings. In the wet state, pigments are combined with a variety of chemical species such as polymers, surfactants, and polyelectrolytes which produce a complex colloidal system. The adsorption, desorption, and redistribution of these species at the pigment-aqueous solution interface can have an impact on the behavior in both the wet state or its final dried state. The goal of this work is to establish a molecular picture of the adsorption properties of these pigmented systems. A novel in situ infrared technique has been developed which allows the detection of adsorbed surface species on pigment particles in an aqueous environment. The technique involves the use of a polymeric binder to anchor the colloidal pigment particles to the surface of an internal reflection element (IRE). The binder only weakly perturbs about 25% of the reactive surface sites (hydroxyl groups) on silica. The reaction of succinic anhydride with an aminosilanized silica surface has been quantified using this technique. The adsorption dynamics of the cationic surfactant cetyltrimethylammonium bromide (C16TAB) at the TiO2-aqueous solution interface has been investigated using Fourier transform infrared-attenuated total reflection spectroscopy (FTIR-ATR) and electrokinetic analysis. At low bulk concentrations, C16TAB is shown to adsorb as isolated islands with a "defective" bilayer structure. Anionic probe molecules are shown to effectively "tune" the adsorbed surfactant microstructure. The results indicate that the structure of the adsorbed surfactant layer, and not the amount of adsorbed surfactant, dictates the subsequent adsorption behavior of the system. Atomic Layer Deposition is used to deposit a TiO2 layer onto the surfaces of silica and kaolin pigments. The process involves the cyclic reaction sequence of the vapors of TiCl4 and H2O. Three complete deposition cycles are needed before the surfaces

Vitrification and neomineralisation of bentonitic and kaolinitic clays ...

African Journals Online (AJOL)

... metamorphic and/or igneous rocks. Resultant fired mineral phases depicted mineral compositions of ceramic bodies, and the study suggested that these clays could be gainfully utilized in the making of ceramic wares, subject to selected beneficiation processes. Keywords: kaolin, bentonite, vitrification, neomineralization, ...

Genesis of some tertiary Indian coals from the chemical composition ...

Indian Academy of Sciences (India)

Baruah. 2008) that in northeast Indian coals, the major minerals (wt% >5) identified in the crystalline matter of coal are quartz, kaolin, illite, feldspar, calcite, pyrite, and gypsum. Vassilev et al. (2010a, b) reported that the rank of the coal increases with.

46 CFR Table 2 to Part 153 - Cargoes Not Regulated Under Subchapters D or O of This Chapter When Carried in Bulk on Non...

Science.gov (United States)

2010-10-01

... solution D Clay slurry III Coal slurry III Dextrose solution, see Glucose solution Diethylenetriamine... hydroxyethylethylenediamine triacetic acid, trisodium salt solution D Fish solubles (water based fish meal extracts) III... solution D N-(Hydroxyethyl)ethylenediamine triacetic acid, trisodium salt solution D Kaolin clay solution...

Obtaining multifunctional composites using styrofoam recycling: methylene blue adsorption; Obtencao de compositos multifuncionais utilizando reciclagem de isopor: adsorcao de azul de metileno

Energy Technology Data Exchange (ETDEWEB)

Silva, T.H. da; Ferreira, B.F.; Faria, E.H. de; Ciuffi, K.J.; Calefi, P.S., E-mail: tiagohonoratosilva@hotmail.com [Universidade de Franca, SP (Brazil)

2011-07-01

There is high risk of environmental contamination by the textile industry if the generated waste is disposed into water streams and rivers. Another sector responsible for the generation of large amounts of waste is the styrofoam industry, since styrofoam is employed in various areas for packaging production. Therefore, today there is constant search for sustainable economic growth by means of materials recycling and reduction of residual pollutants. In this context, the present work aims to promote styrofoam recycling with its further utilization in the production of a kaolin-styrofoam composite for application as adsorbent of methylene blue originated from textile industry effluents. This adsorption is investigated in a column system, by exploiting the adsorptive properties of kaolin, such as large surface area and chemical and structural characteristics. The obtained materials were characterized by thermogravimetric analysis, X-ray diffraction, and UV-visible absorption spectroscopy. (author)

Obtaining multifunctional composites using styrofoam recycling: methylene blue adsorption

International Nuclear Information System (INIS)

Silva, T.H. da; Ferreira, B.F.; Faria, E.H. de; Ciuffi, K.J.; Calefi, P.S.

2011-01-01

There is high risk of environmental contamination by the textile industry if the generated waste is disposed into water streams and rivers. Another sector responsible for the generation of large amounts of waste is the styrofoam industry, since styrofoam is employed in various areas for packaging production. Therefore, today there is constant search for sustainable economic growth by means of materials recycling and reduction of residual pollutants. In this context, the present work aims to promote styrofoam recycling with its further utilization in the production of a kaolin-styrofoam composite for application as adsorbent of methylene blue originated from textile industry effluents. This adsorption is investigated in a column system, by exploiting the adsorptive properties of kaolin, such as large surface area and chemical and structural characteristics. The obtained materials were characterized by thermogravimetric analysis, X-ray diffraction, and UV-visible absorption spectroscopy. (author)

X-ray texture analysis of paper coating pigments and the correlation with chemical composition analysis

Science.gov (United States)

Roine, J.; Tenho, M.; Murtomaa, M.; Lehto, V.-P.; Kansanaho, R.

2007-10-01

The present research experiments the applicability of x-ray texture analysis in investigating the properties of paper coatings. The preferred orientations of kaolin, talc, ground calcium carbonate, and precipitated calcium carbonate particles used in four different paper coatings were determined qualitatively based on the measured crystal orientation data. The extent of the orientation, namely, the degree of the texture of each pigment, was characterized quantitatively using a single parameter. As a result, the effect of paper calendering is clearly seen as an increase on the degree of texture of the coating pigments. The effect of calendering on the preferred orientation of kaolin was also evident in an independent energy dispersive spectrometer analysis on micrometer scale and an electron spectroscopy for chemical analysis on nanometer scale. Thus, the present work proves x-ray texture analysis to be a potential research tool for characterizing the properties of paper coating layers.

MR elastography of hydrocephalus

Science.gov (United States)

Pattison, Adam J.; Lollis, S. Scott; Perrinez, Phillip R.; Weaver, John B.; Paulsen, Keith D.

2009-02-01

Hydrocephalus occurs due to a blockage in the transmission of cerebrospinal fluid (CSF) in either the ventricles or subarachnoid space. Characteristics of this condition include increased intracranial pressure, which can result in neurologic deterioration [1]. Magnetic resonance elastography (MRE) is an imaging technique that estimates the mechanical properties of tissue in vivo. While some investigations of brain tissue have been performed using MRE [2,3,4,5], the effects due to changes in interstitial pressure and fluid content on the mechanical properties of the brain remain unknown. The purpose of this work is to assess the potential of MRE to differentiate between the reconstructed properties of normal and hydrocephalic brains. MRE data was acquired in 18 female feline subjects, 12 of which received kaolin injections resulting in an acute form of hydrocephalus. In each animal, four MRE scans were performed during the process including one pre-injection and three post-injection scans. The elastic parameters were obtained using a subzone-based reconstruction algorithm that solves Navier's equations for linearly elastic materials [6]. The remaining cats were used as controls, injected with saline instead of kaolin. To determine the state of hydrocephalus, ventricular volume was estimated from segmenting anatomical images. The mean ventricular volume of hydrocephalic cats significantly increased (P ~ 0.5) for the control cats. Also, there was an observable increase in the recorded elastic shear modulus of brain tissue in the normal and hydrocephalic acquisitions. Results suggest that MRE is able to detect changes in the mechanical properties of brain tissue resulting from kaolin-induced hydrocephalus, indicating the need for further study.

Analysis of Some Clay Samples from Yauri (Kebbi State), Goronyo ...

African Journals Online (AJOL)

Analysis of some clay samples presumed to be kaolin obtained from different deposits in Yauri (kebbi state), Goronyo, Munwadata, Atokonyo (Sokoto state), Nigeria was carried out. The samples were subjected to quantitative analysis to determine major and trace constituents using gravimetric, colorimetric, titrimetric and ...

Novel composite sorbent AAm/MA hydrogels containing starch and ...

Indian Academy of Sciences (India)

A novel polymer/clay composite sorbent based on acrylamide/maleic acid, starch and clay such as kaolin was synthesized with free radical solution polymerization by using ammonium persulfate/,,','-tetramethylethylenediamine as redox initiating pair in the presence of poly(ethylene glycol)diacrylate as a crosslinker.

13 CFR 121.201 - What size standards has SBA identified by North American Industry Classification System codes?

Science.gov (United States)

2010-01-01

... 500 212322 Industrial Sand Mining 500 212324 Kaolin and Ball Clay Mining 500 212325 Clay and Ceramic... Manufacturing 500 322215 Non-Folding Sanitary Food Container Manufacturing 750 322221 Coated and Laminated... Manufacturing 500 322233 Stationery, Tablet, and Related Product Manufacturing 500 322291 Sanitary Paper Product...

Kaolins in Uruguay; Caolines en el Uruguay

Energy Technology Data Exchange (ETDEWEB)

Spoturno, J; Coronel, N

1980-07-01

This work belongs to the Syllabus or Mundial monograph about caolines. Its was organized by the number 23 working group caolines genesis of the International geological correlation Unesco programme. History, geology, tectonic development, sedimentation, dating and geochemistry aspects were given in this report.

Ash transformation in suspension fired boilers co-firing coal and straw

DEFF Research Database (Denmark)

Zheng, Yuanjing; Jensen, Peter Arendt; Jensen, Anker Degn

To study the influence of local conditions on the reaction between gaseous KCl and kaolin or coal fly ash experiments were done on CHECs electrically heated entrained flow reactor, which can simulate the local conditions in suspension fired boilers. The experimental results were compared with mod...

Cost and Performance Report of Electrical Resistance Heating (ERH) for Source Treatment. Addendum

Science.gov (United States)

2008-09-29

remains and thin sandy layers. Patuxent Multiple-Layer Aquifer Sand, gray and yellow, with interbedded clay, kaolinized feldspar, pyrite and lignite...treatment. However, the post-treatment CVOC mass is likely to be even more sporadically dispersed than the pre-treatment CVOC mass, leading to similar (or

Using the Fish Larvae and Egg Exposure System (FLEES) to Generate Effects Data for Informing Environmental Windows

Science.gov (United States)

2017-03-01

not stationary and continuously move as dredge materials are removed; and 3) the fanning behavior of fish, such as SMB, can disperse fine-grained...235–249. Gordon, A. K., and C. G. Palmer. 2015. Defining an exposure-response relationship for suspended kaolin clay particulates and aquatic

Response of Phlebotomine Sand Flies to Light-Emitting Diode-Modified Light Traps in Southern Egypt

Science.gov (United States)

2007-04-01

dispersal , and oviposition site selection (Allan et al. 1987, Allan 1994, Snow 1971). Target size, shape, movement, contrast, and color are...dogs, and goats. The village is built from baked mud bricks and covered with kaolin day to produce hardened, smooth wall surfaces, structures are one

Preparation, Characterization and Performance of Conch Ceramics Added With Shell

Directory of Open Access Journals (Sweden)

Wang Qingyu

2016-01-01

Full Text Available The conch ceramics bodies with different ratios were prepared by compression moulding technology using shell, kaolin, and calcium oxide etc. as the raw materials, and then calcined at the high temperature to obtain the conch ceramics. The effects of raw material ratios and calcination temperatures on the performance of conch ceramics were investigated by rotational viscometer, vernier caliper, digital display whiteness meter, thermal analyzer, and Fourier transform infrared spectrometer(FT-IR. The results indicated that the viscosity, line shrinkage rate, and whiteness of the conch ceramics were 1.29 Pa·s, 17.9%, and 54.1%, respectively, when the content of the shell powder was 20 wt% and kaolin was 65 wt%. The density of the conch ceramics was the largest (3.8 g/cm3 when calcination temperature was 1200 °C. The results of FT-IR spectrum showed that the addition of the shell powders changed the structure of the ceramic body, which improved the performance of the conch ceramics.

Zeolit Sintetis Terfungsionalisasi 3-(Trimetoksisilil-1-Propantiol sebagai Adsorben Kation Cu(II dan Biru Metilena

Directory of Open Access Journals (Sweden)

Sri Sugiarti

2017-05-01

Full Text Available The more commonly used method for making synthetic zeolite from kaolin is hydrothermal method. This research tested a sol-gel method in processing synthetic zeolit  using kaolin as the basic ingrediant. The synthetic  zeolite  derived from the sol-gel method was then characterized using X-ray Difractometer and Scanning Electron Microscope, which found resulting products zeolite-A, zeolite Y and sodalite. The adsorption ability of the synthetic zeolites was tested using Cu(II and methylene blue.  Functionalization of the synthetic zeolites by 3-(trimetoksisilil-1-propantiol was  done to increase adsorption capacity. Zeolite A modified by 3-(trimetoksisilil-1-propantiol  had the greater capacity to adsorb methylene blue at 30.11 mg/g. The adsorption isotherms of all the synthetic zeolites approached the Langmuir form. The adsorption energy off all synthetic zeolites approached the chemical adsorption.DOI: http://dx.doi.org/10.15408/jkv.v0i0.5144

Recombinant protein expression of Moringa oleifera lectin in methylotrophic yeast as active coagulant for sustainable high turbid water treatment.

Science.gov (United States)

Abd Wahid, Muhamad Azhar; Megat Mohd Noor, Megat Johari; Goto, Masafumi; Sugiura, Norio; Othman, Nor'azizi; Zakaria, Zuriati; Ahmad Mohammed, Thamer; Jusoh, Ahmad; Hara, Hirofumi

2017-08-01

The natural coagulant Moringa oleifera lectin (MoL) as cationic protein is a promising candidate in coagulation process of water treatment plant. Introducing the gene encoding MoL into a host, Pichia pastoris, to secrete soluble recombinant protein is assessed in this study. Initial screening using PCR confirmed the insertion of MoL gene, and SDS-PAGE analysis detected the MoL protein at 8 kDa. Cultured optimization showed the highest MoL protein at 520 mg/L was observed at 28 °C for 144 h of culturing by induction in 1% methanol. Approximately, 0.40 mg/mL of recombinant MoL protein showed 95 ± 2% turbidity removal of 1% kaolin suspension. In 0.1% kaolin suspension, the concentration of MoL at 10 μg/mL exhibits the highest turbidity reduction at 68 ± 1%. Thus, recombinant MoL protein from P. pastoris is an effective coagulant for water treatment.

Thermal properties of clay-based buffer materials for a nuclear fuel waste disposal vault

International Nuclear Information System (INIS)

Radhakrishna, H.S.

1984-06-01

The thermal properties of three types of bentonite clay, one illite-rich shale and one kaolin mixed with crushed granite were investigated. Thermal conductivity measurements were made over a range of mix proportions, moisture content, density and ambient temperature using the transient heat-probe method. The effects of thermal drying in the buffer zone prior to water uptake were investigated by means of laboratory-scale heater experiments. Illite-rich shale (Sealbond) and kaolin exhibited better compactability and thermal conductivity than the bentonite clays. The thermal conductivity of all types of clay buffers showed a high degree of moisture dependency and relatively no effect due to elevated temperature under high fluid pressure conditions. Bentonite buffers compacted to a dry density of 1200 to 1400 kg/m 3 showed extensive cracking due to differential shrinkage. Addition of crushed granite, and/or compaction to a higher density, reduced the thermal cracking of the buffer material

SODIUM TITANATE NANOBELT AS A MICROPARTICLE TO INDUCE CLAY FLOCCULATION WITH CPAM

Directory of Open Access Journals (Sweden)

Wenxia Liu

2010-07-01

Full Text Available Sodium titanate nanobelt was synthesized by treating titanium dioxide hydrothermally in concentrated sodium hydroxide solution. The product was characterized by SEM analysis and zeta potential measurement. It served as a microparticle to constitute a microparticle retention system with cationic polyacrylamide (CPAM, while the microparticle system was employed to induce the flocculation of kaolin clay. The flocculation behavior of kaolin clay in such a system was investigated by using a photometric dispersion analyzer connected with a dynamic drainage jar. It was found that the sodium titanate nanobelt carried negative charges and had a lower zeta potential at higher pH. It gave a large synergistic flocculation effect with CPAM at a very low dosage, and showed higher flocculation effect with CPAM under neutral and weak alkaline conditions. A suitably high shear level was helpful for the re-flocculation of clay by sodium titanate nanobelt. The clay flocculation induced by CPAM/titanate nanobelt system demonstrated high shear resistance and also generated dense flocs.

Mullite evolution in ceramics derived from clay, and sol-gel precursors

International Nuclear Information System (INIS)

Rezaie, H.R.; Naghizadeh, R.; Golestani-Fard, F.

2002-01-01

Mullite formation from sol-gel (behemoth and colloidal silica), and clay has been compared and the microstructural evolution examined using electron-optical techniques and XRD. The relationship between processing route and reaction sequence to form mullite is discussed. In sol-gel processing γAloof transforms to γ-Al 2 O 3 at 400-500 d eg w ithout an isothermal hold. δ-Al 2 O 3 was present after cooling directly from 1100 d eg i n air.(δ+θ)Al 2 O 3 were present above 1200 d eg . Reaction between (δ+θ)Al 2 O 3 and amorphous silica produced 3:2 mullite at∼ 1370 d eg . In kaolin, meta kaolin transforms to spinel and mullite at 980-1000 d eg w ithout an isothermal hold. Melanostatin to 3:2 mullite took place at 1200-1250 d eg . Cristobalite was observed after quenching from 1200 d eg , but could not be detected after cooling directly from 1590 d eg

Characteristics of a bioflocculant produced by a consortium of ...

African Journals Online (AJOL)

The characteristics of a bioflocculant produced by a consortium of 2 bacteria belonging to the genera Cobetia and Bacillus was investigated. The extracellular bioflocculant was composed of 66% uronic acid and 31% protein and showed an optimum flocculation (90% flocculating activity) of kaolin suspension at a dosage of ...

Introduction

International Nuclear Information System (INIS)

Mirsaidov, U.M.

2002-01-01

In this part of book author gives short description of science elaborations such as: ferrosilicon receiving from wastes, synthetic iron production from scrap in the induction furnace, was elaborated method of local kaolin clays using, on the base of apple pectin was elaborated new medical products and etc

THROMBOELASTOGRAPHY IN THE HEALTHY ASIAN ELEPHANT (ELEPHAS MAXIMUS)

DEFF Research Database (Denmark)

Perrin, Kathryn L.; Krogh, Anne K.; Kjelgaard-Hansen, Mads

2018-01-01

elephants. Kaolin-activated TEG was performed on whole blood at 60 min and 24 hr postsampling (to replicate shipment to an external laboratory) as well as on freeze–thawed plasma samples, 12–14 mo postsampling. Reference intervals were calculated for fresh whole blood and freeze–thawed plasma samples...

Effect of Temperature on Mechanical Properties of Nanoclay Reinforced Polymeric Nanocomposites. Part 1. Experimental Results

Science.gov (United States)

2012-04-23

Sugiyama, T. Kurashi, O. Kamigaito., U.S. 4,739,007 (1998). UNCLASSIFIED 22 [4] Nguyen Q. T., Process for Improving Exfoliation and Dispersion of...polyethylene/ Kaolin composites. Part II. Thermoelastic behavior of blow-molded samples. J Mater Sci 34 (1999), pp. 497–508. [22] J.S. Bergman, H

Soft Soil Improvement for Sub-grade Layer Using Hexagonal Micropiles Layout

Science.gov (United States)

Ambak, K.; Abdullah, N. A. H.; Yusoff, M. F.; Abidin, M. H. Z.

2018-04-01

Soft soil problems are often associated with sediment and stability where it represents a major challenge in Geotechnical Engineering. Research on a soft soil was carried out to determine the level of sediment resulting from the applied load and thus compare the most ideal form of arrangement by the results obtained from bearing capacity. The study was conducted at Research Centre for Soft Soil (RECESS), UTHM by using kaolin. There are several tests conducted on kaolin before the arrangement of pile which is liquid limit test. Through these tests, the level of water content can be maintained which is 1.2 liquid limit where it is in the homogeneous condition. Density test also carried to know weight of kaolin and water that needed in the model. Meanwhile, large strain consolidation test carried on the soil by placing a load of 8 kPa. Then, the pile was arranged in the soil in the shape of a hexagon and square. Load was increased to 12 kPa and imposed on the surface of the pile with a different forms. After 24 hours, the reading of sediment was measured everyday and the process collecting data conducted for 3 week. Based on data obtained, time against sediment can be plotted. To determine the bearing capacity, direct shear test was conducted to get the value coefficient of cohesion, c as a parameter in the calculation of the soil bearing capacity. The results showed that the rate of settlement occurs is different where hexagonal form less the rate of settlement compared to square form which is 64.2% while the results of bearing capacity have the same value.

Removal of antibiotics from water in the coexistence of suspended particles and natural organic matters using amino-acid-modified-chitosan flocculants: A combined experimental and theoretical study

International Nuclear Information System (INIS)

Jia, Shuying; Yang, Zhen; Ren, Kexin; Tian, Ziqi; Dong, Chang; Ma, Ruixue; Yu, Ge; Yang, Weiben

2016-01-01

Highlights: • Novel amino-acid-modified-chitosan flocculants are employed to remove antibiotics. • Effects of different structures of amino acids and antibiotics are investigated. • Correlation analysis shows coexisted kaolin and HA have synergistic removal effect. • Theoretical DFT calculation clarifies the interactions in molecular level. - Abstract: Contamination of trace antibiotics is widely found in surface water sources. This work delineates removal of trace antibiotics (norfloxacin (NOR), sulfadiazine (SDZ) or tylosin (TYL)) from synthetic surface water by flocculation, in the coexistence of inorganic suspended particles (kaolin) and natural organic matter (humic acid, HA). To avoid extra pollution caused by petrochemical products-based modification reagents, environmental-friendly amino-acid-modified-chitosan flocculants, Ctrp and Ctyr, with different functional aromatic-rings structures were employed. Jar tests at various pHs exhibited that, Ctyr, owning phenol groups as electron donors, was favored for elimination of cationic NOR (∼50% removal; optimal pH: 6; optimal dosage: 4 mg/L) and TYL (∼60% removal; optimal pH: 7; optimal dosage: 7.5 mg/L), due to π–π electron donator-acceptor (EDA) effect and unconventional H-bonds. Differently, Ctrp with indole groups as electron acceptor had better removal rate (∼50%) of SDZ anions (electron donator). According to correlation analysis, the coexisted kaolin and HA played positive roles in antibiotics’ removal. Detailed pairwise interactions in molecular level among different components were clarified by spectral analysis and theoretical calculations (density functional theory), which are important for both the structural design of new flocculants aiming at targeted contaminants and understanding the environmental behaviors of antibiotics in water.

Removal of antibiotics from water in the coexistence of suspended particles and natural organic matters using amino-acid-modified-chitosan flocculants: A combined experimental and theoretical study

Energy Technology Data Exchange (ETDEWEB)

Jia, Shuying [School of Chemistry and Materials Science, Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing Normal University, Nanjing 210023 (China); Yang, Zhen, E-mail: yangzhen@njnu.edu.cn [School of Chemistry and Materials Science, Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing Normal University, Nanjing 210023 (China); Ren, Kexin [School of Chemistry and Materials Science, Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing Normal University, Nanjing 210023 (China); Tian, Ziqi [Department of Chemistry, University of California, Riverside, CA 92521 (United States); Dong, Chang; Ma, Ruixue; Yu, Ge [School of Chemistry and Materials Science, Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing Normal University, Nanjing 210023 (China); Yang, Weiben, E-mail: yangwb007@njnu.edu.cn [School of Chemistry and Materials Science, Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing Normal University, Nanjing 210023 (China)

2016-11-05

Highlights: • Novel amino-acid-modified-chitosan flocculants are employed to remove antibiotics. • Effects of different structures of amino acids and antibiotics are investigated. • Correlation analysis shows coexisted kaolin and HA have synergistic removal effect. • Theoretical DFT calculation clarifies the interactions in molecular level. - Abstract: Contamination of trace antibiotics is widely found in surface water sources. This work delineates removal of trace antibiotics (norfloxacin (NOR), sulfadiazine (SDZ) or tylosin (TYL)) from synthetic surface water by flocculation, in the coexistence of inorganic suspended particles (kaolin) and natural organic matter (humic acid, HA). To avoid extra pollution caused by petrochemical products-based modification reagents, environmental-friendly amino-acid-modified-chitosan flocculants, Ctrp and Ctyr, with different functional aromatic-rings structures were employed. Jar tests at various pHs exhibited that, Ctyr, owning phenol groups as electron donors, was favored for elimination of cationic NOR (∼50% removal; optimal pH: 6; optimal dosage: 4 mg/L) and TYL (∼60% removal; optimal pH: 7; optimal dosage: 7.5 mg/L), due to π–π electron donator-acceptor (EDA) effect and unconventional H-bonds. Differently, Ctrp with indole groups as electron acceptor had better removal rate (∼50%) of SDZ anions (electron donator). According to correlation analysis, the coexisted kaolin and HA played positive roles in antibiotics’ removal. Detailed pairwise interactions in molecular level among different components were clarified by spectral analysis and theoretical calculations (density functional theory), which are important for both the structural design of new flocculants aiming at targeted contaminants and understanding the environmental behaviors of antibiotics in water.

Measurements, characterizing and reduction of dust during combustion of energy grain; Maetning, karaktaerisering och reduktion av stoft vid eldning av spannmaal

Energy Technology Data Exchange (ETDEWEB)

Roennbaeck, Marie; Johansson, Linda; Claesson, Frida; Johansson, Mathias

2008-07-01

There is a potential for cereal grain for combustion use in Sweden, as well as for other agricultural fuels with similar qualities. Today, grain is combusted mainly in small-scale appliances. As all fast growing crops, the ash content is higher compared to wood fuels, resulting in a higher emission of particles. There are no limits for particle emission from appliances smaller than 500 kW in Sweden today. Nevertheless, it is important to consider these emissions because dust from small scale combustion of biofuels is one of the larger sources of particles to air in Sweden and in Europe today. Lately, is has been observed that the ultra fine particles (< 0.1 mum) is a cause of increased mortality. During large-scale combustion, the flue gas is cleaned from particles by electrostatic or fabric filters. During small-scale combustion primary measures is preferred by economical reasons. Particles can be reduced by design of the appliances or control of the combustion process. It might also be possible to reduce particles by use of additives that ties the volatile matters to the bottom ash and/or causes them leave as gas instead of particles. The aim of this project is to characterize and reduce particle emissions from combustion of cereal grain by use of additives. Limestone and kaolin were tested in a burner for oat grain. Particle emission was measured as total dust, as mass size distributed and as number size distributed. Fuel, bottom ash and dust were characterized chemically. In the flue gas carbon monoxide, carbon dioxide, oxygen, hydrocarbons, nitrogen oxide, sulphur dioxide and hydrogen chloride was measured. Equilibrium calculations were performed for combustion with and without additives. The combustion was not negatively influenced by the additives. The results confirm that lime stone reduces emissions of acidifying and corrosive gases such as sulphur dioxide and hydrogen chloride. Both lime stone and kaolin increase the ash fusion temperature. Results from

Experiments of the origins of optical activity.

Science.gov (United States)

Bonner, W A; Flores, J J

1975-01-01

Two recent reports claim that (1) aqueous L-aspartic acid polymerizes faster than D-Asp in the presence of kaolin at 90 degrees, and (2) L-phenylalanine is adsorbed by kaolin more extensively than D-Phe at pH 4(the reverse being true at pH2). The novelty of these observations and their potential significance for the origin of optical activity has prompted us to duplicate these experiments using more sensitive methods. L- and D, L-Asp in 0.01 M solution were incubated with kaolin at 90 degrees for 8 days. Careful examination of the aqueous residues from such experiments failed to demonstrate any preferential polymerization of L-Asp over D-Asp, or indeed any significant gross polymerization of Asp at all. In other experiments 0.001 M solutions of D, L-Phe at pH 6 and pH 2 were stirred with large excesses of kaolin for 24 hr, and the aqueous extracts from these mixtures were examined for gross adsorption using the amino acid analyzer. No significant gross adsorption was noted. We then looked for asymmetric adsorption in the aqueous residues using optical rotatory dispersion, gas chromatography and thin layer chromatography. By none of these analytical criteria could we find any evidence whatsoever for the preferential adsorption of D- versus L-Phe from either pH 6 or pH 2 solutions. Finally, in experiments bearing on the origin of optical activity by parity violation during beta-decay, we have irradiated solid samples of D-, L- and D,L-leucine in a 61700 Ci Sr-90 source at Oak Ridge National Lab. for 1.34 yr (total dose: 4.2 x 10(8) rad). Gas chromatographic examination of the (appropriately derivitized) recovered samples showed that the L-Leu was 16.7% decomposed, the D-Leu 11.4% and theD,L-Leu 13.8% decomposed. The recovered D,L-Leu sample had a gas-chromatographically determined enantiomeric composition of 50.8% D-leu and 49.2% L-Leu. These data, though very close to experimental error, may indicate a slight preferential radiolysis of L-Leu compared to D-Leu by the

Centrifuge modelling of rigid piles in soft clay

DEFF Research Database (Denmark)

Klinkvort, R.T.; Poder, M.; Truong, P.

2016-01-01

of this study is to employ centrifuge modelling in order to derive experimental p-y curves for rigid piles embedded in over-consolidated soft clay. A kaolin clay sample was prepared and pre-consolidated by applying a constant pressure at the soil surface, while different over-consolidation ratios were achieved...

Principal component analysis to evaluate the spatial variation of ...

African Journals Online (AJOL)

Discretisation of the particle sizes is highlighted as both a challenge and an opportunity and it is recommended that it be used as a tuning parameter in gauging kaolin variations across samples and in validating new predictive modeling applications. Successful applications will depend on how clay and data scientists keep ...

Entrained Flow Reactor Study of K-Capture by Solid Additives

DEFF Research Database (Denmark)

Wang, Guoliang; Jensen, Peter Arendt; Wu, Hao

2016-01-01

are collected from the cyclone and filter. The K-capture reaction is evaluated by determining the fraction of water-insoluble K in the products. The results showed that KCl can effectively be captured by kaolin and coal fly ash, forming water-insoluble K-aluminosilicates. The amount of K, captured per gram...

Rheology and extrusion of low-grade paper and sludge

Science.gov (United States)

C. Tim Scott; Stefan Zauscher; Daniel J. Klingenberg

1999-01-01

This paper discusses efforts to characterize the rheological properties of pulps that include low-grade wastepapers and papermill sludges to determine their potential for extrusion and conversion into useful products. We investigated apparent changes in viscosity associated with the addition of typical inorganic paper fillers (calcium carbonate, kaolin clay, and...

The prevalence ofantiphospholipid antibodies in women with ...

African Journals Online (AJOL)

patients. PTT, APTT, kaolin clotting time (KCT),. Russell viper venom time CRvvn were measured in all the subjects, who were also assessed for the presence of anticardiolipin antibodies. Blood was taken by venepuncture into a 0,1 volume of 3,8% trisodium citrate. Platelet-rich plasma (PRP) was prepared by centrifuging of ...

Drag reduction of dense fine-grained slurries

Czech Academy of Sciences Publication Activity Database

Vlasák, Pavel; Chára, Zdeněk; Štern, Petr

2010-01-01

Roč. 58, č. 4 (2010), s. 261-270 ISSN 0042-790X R&D Projects: GA ČR(CZ) GAP105/10/1574 Institutional research plan: CEZ:AV0Z20600510 Keywords : kaolin slurry * drag reduction * experimental investigation * peptization * slurry rheology Subject RIV: BK - Fluid Dynamics Impact factor: 0.553, year: 2010

75 FR 70203 - Certain Coated Paper Suitable for High-Quality Print Graphics Using Sheet-Fed Presses From the...

Science.gov (United States)

2010-11-17

... Error Memo. In addition, one of the ministerial errors affected the calculation of the labor rate, which... quality print graphics using sheet-fed presses; coated on one or both sides with kaolin (china or other...; whether gloss grade, satin grade, matte grade, dull grade, or any other grade of finish; whether or not...

75 FR 75663 - Certain Coated Paper Suitable for High-Quality Print Graphics Using Sheet-Fed Presses From the...

Science.gov (United States)

2010-12-06

... suitable for high quality print graphics using sheet-fed presses; coated on one or both sides with kaolin... square meter; whether gloss grade, satin grade, matte grade, dull grade, or any other grade of finish... distinguish it from `text.' \\2\\ One of the key measurements of any grade of paper is brightness. Generally...

AIRIS Wide Area Detection System

Science.gov (United States)

2003-07-01

herbicola, the chemical stimulant SF6, as well as the interferents kaolin clay dust, Dugway road dust, and diesel soot. In this paper we will report on...the SF6 column density of approximately 200 ppmv-m. In future work we hope to correlate this measurement with a Gaussian plume dispersion model of

Síntese de zeólita tipo NaA a partir de caulim para obtenção de zeólita 5A através de troca iônica Synthesis of NaA zeolites from kaolin for obtaining 5A zeolites through ion exchange

Directory of Open Access Journals (Sweden)

C. R. Melo

2010-12-01

Full Text Available A síntese de zeólitas com o intuito de utilizá-las posteriormente como materiais adsorventes exige rigoroso controle das variáveis de processamento. Para cada tipo diferente de zeólita, existem variáveis de processo distintas para obtenção do tipo específico desejado. Neste trabalho os objetivos foram obter zeólita NaA partindo de caulim, para posteriormente obter zeólita 5A por meio de troca iônica com esta zeólita anteriormente sintetizada. Estas zeólitas, por sua vez, podem ser usadas como adsorventes altamente seletivos para adsorver, por exemplo, metais pesados de efluentes industriais. Os resultados obtidos foram satisfatórios, a metodologia utilizada mostrou-se eficiente. A partir do metacaulim comercial utilizado, obteve-se com sucesso zeólita tipo NaA, e por meio de trocas iônicas obteve-se zeólita 5A. A porcentagem de sódio trocada na zeólita final foi 61,4%.Zeolites synthesis as adsorbing materials requires accurate control of the variables. There are distinct process variables for obtaining specific desired types depending on each different kind of zeolite to be synthesized. This paper was aimed at obtaining NaA zeolites from kaolin in order to obtain zeolites A afterwards through ionic exchange with the previously synthesized zeolite. These zeolites can then be used as highly selective adsorbents to adsorb, for instance, heavy metals in industrial effluents. The results obtained were satisfactory, the methodology was efficient. From the commercial metakaolin used NaA zeolite was obtained successfully, and through ionic exchanges 5A zeolite was obtained. The exchangeable sodium percentage in the final zeolite was 61.4%.

Características físicas dos minérios de caulim das minas floresta, Cavalheiro, Turvo e Kowalski, em Campo Alegre (SC, e de Trigolândia (PR Physical characteristics of kaolin ores from Floresta, Cavalheiro, Turvo and Kowalski Mines (SC and from Trigolândia Mine (PR

Directory of Open Access Journals (Sweden)

J. C. Biondiv

2000-06-01

Full Text Available A OXFORD fez, em seus minérios, 244 determinações de resistência a flexão, 1601 determinações da retração do minério a 110 ºC, 1508 determinações da retração após queima a 1220 ºC, 877 determinações de perda ao fogo, 1544 de absorção de água, 2288 determinações da dilatação linear a após secagem a 110 ºC e 1128 da dilatação linear após queima a 1220 ºC. Os valores médios, máximos, mínimos e as distribuições dos resultados dessas análises estão mostrados em tabelas e gráficos. Essas determinações e as observações de campo mostram que os depósitos estudados são de dois tipos, denominados Modelo Trigolândia, derivado de pegmatitos, e Modelo Floresta, derivado de rochas vulcânicas ácidas. Com exceção do minério da Mina do Turvo, as médias dos valores das propriedades físicas analisadas estão sempre dentro do intervalo de valores suportado pelo processo industrial da OXFORD. O minério verde, quase todo da Mina Turvo, e o minério marron são os que têm propriedades mais discordantes dos padrões desejados. Nas correlações entre os valores médios das propriedades físicas analisadas foi constatado que as correlações ruins são sempre devidas ao minério de Trigolândia. Considerando todos os valores analisados e não mais as suas médias, nota-se que, com exceção da correlação entre a % de retração após secagem a 110 ºC e a % de retração total, com r = 0,78, todos os outros coeficientes de correlação são muito baixos, menores que 0,60.OXFORD has made 244 determinations of modulus of rupture, 1601 determinations of dry contraction 110 ºC, 1508 determinations of fired contraction 1220 ºC, 877 determinations of ignition loss, 1544 determinations of apparent porosity, 2288 determinations of dry linear dilation (dried at 110 ºC and 1128 determinations of fired linear dilation (fired at 1220 ºC on their kaolin ores. The averages, maximum, minimum and the statistical distribution

Effects of triethyl phosphate and nitrate on electrokinetically enhanced biodegradation of diesel in low permeability soils.

Science.gov (United States)

Lee, G T; Ro, H M; Lee, S M

2007-08-01

Bench-scale experiments for electrokinetically enhanced bioremediation of diesel in low permeability soils were conducted. An electrokinetic reactor (ER) was filled with kaolin that was artificially contaminated with diesel at a level of 2500 mg kg(-1). A constant voltage gradient of 1.0 V cm(-1) was applied. In phosphorus transport experiments, KH2PO4 was not distributed homogeneously along the ER, and most of the transported phosphorus was converted to water-insoluble aluminum phosphate after 12 days of electrokinetic (EK) operation. However, the advancing P front of triethyl phosphate (TEP) progressed with time and resulted in uniform P distribution. The treatments employed in the electrokinetically enhanced bioremediation of diesel were control (no addition of nitrogen and phosphorus), NP (KNO3+ KH2PO4), NT (KNO3+ TEP), UP (urea+ KH2PO4), and UT (urea+TEP). Analysis of effluent collected during the first 12 days of EK operation showed that diesel was not removed from the kaolin. After nutrient delivery, using the EK operation, the ER was transferred into an incubator for the biodegradation process. After 60 days of biodegradation, the concentrations of diesel in the kaolin for the NP, NT, UP, UT, and control treatments were 1356, 1002, 1658, 1612, and 2003 mg kg(-1), respectively. The ratio of biodegraded diesel concentration to initial concentration (2465 mg kg(-1)) in NP, NT, UP, UT, and control were 45.0%, 59.4%, 32.7%, 34.6%, and 18.7%, respectively. This result showed that TEP, treated along with NO3-, was most effective for the biodegradation of diesel. TEP was delivered more efficiently to the target zones and with less phosphorus loss than KH2PO4. However, this facilitated phosphorus delivery was effective in biodegrading diesel under anaerobic conditions only when electron acceptors, such as NO3-, were present.

Morphology of Gas Release in Physical Simulants

Energy Technology Data Exchange (ETDEWEB)

Daniel, Richard C.; Burns, Carolyn A.; Crawford, Amanda D.; Hylden, Laura R.; Bryan, Samuel A.; MacFarlan, Paul J.; Gauglitz, Phillip A.

2014-07-03

This report documents testing activities conducted as part of the Deep Sludge Gas Release Event Project (DSGREP). The testing described in this report focused on evaluating the potential retention and release mechanisms of hydrogen bubbles in underground radioactive waste storage tanks at Hanford. The goal of the testing was to evaluate the rate, extent, and morphology of gas release events in simulant materials. Previous, undocumented scoping tests have evidenced dramatically different gas release behavior from simulants with similar physical properties. Specifically, previous gas release tests have evaluated the extent of release of 30 Pa kaolin and 30 Pa bentonite clay slurries. While both materials are clays and both have equivalent material shear strength using a shear vane, it was found that upon stirring, gas was released immediately and completely from bentonite clay slurry while little if any gas was released from the kaolin slurry. The motivation for the current work is to replicate these tests in a controlled quality test environment and to evaluate the release behavior for another simulant used in DSGREP testing. Three simulant materials were evaluated: 1) a 30 Pa kaolin clay slurry, 2) a 30 Pa bentonite clay slurry, and 3) Rayleigh-Taylor (RT) Simulant (a simulant designed to support DSGREP RT instability testing. Entrained gas was generated in these simulant materials using two methods: 1) application of vacuum over about a 1-minute period to nucleate dissolved gas within the simulant and 2) addition of hydrogen peroxide to generate gas by peroxide decomposition in the simulants over about a 16-hour period. Bubble release was effected by vibrating the test material using an external vibrating table. When testing with hydrogen peroxide, gas release was also accomplished by stirring of the simulant.

Analysis of thermal process of pozzolan production

Directory of Open Access Journals (Sweden)

Mejía De Gutiérrez, R.

2004-06-01

Full Text Available The objective of this study was evaluated the effect of heat treatment parameters on the pozzolanic activity of natural kaolin clays. The experimental design included three factors: kaolin type, temperature and time. Five types of Colombian kaolin clays were thermally treated from 400 to 1000 °C by 1, 2, and 3 hours. The raw materials and the products obtained were characterized by X-Ray Diffraction (XRD, Fourier Transform Infrared Spectroscopy (FTIR and Differential Thermal / Thermo gravimetric Analysis (DTAJ TGA. The pozzolanic activity of thermally treated samples according to chemical and mechanical tests was investigated.

El objetivo de este estudio fue caracterizar las variables de producción de un metacaolín de alta reactividad puzolánica. El diseño experimental utilizó un modelo factorial que consideró tres factores: tipo de caolín (C, temperatura y tiempo. A partir del conocimiento de las fuentes de caolín y el contacto con proveedores y distribuidores del producto a nivel nacional, se seleccionaron cinco muestras representativas de arcillas caoliníticas, las cuales se sometieron a un tratamiento térmico entre 400 y 1.000 ºC (seis niveles de temperatura y tres tiempos de exposición, 1, 2 y 3 horas. Los caolines de origen y los productos obtenidos de cada proceso térmico fueron evaluados mediante técnicas de tipo físico y químico, difracción de rayos X, infrarrojo FTIR, y análisis térmico diferencial (OTA, TGA. Complementariamente se evalúa la actividad puzolánica, tanto química como mecánica, del producto obtenido a diferentes temperaturas de estudio.

Effects of mineral additives on biochar formation: carbon retention, stability, and properties.

Science.gov (United States)

Li, Feiyue; Cao, Xinde; Zhao, Ling; Wang, Jianfei; Ding, Zhenliang

2014-10-07

Biochar is being recognized as a promising tool for long-term carbon sequestration, and biochar with high carbon retention and strong stability is supposed to be explored for that purpose. In this study, three minerals, including kaolin, calcite (CaCO3), and calcium dihydrogen phosphate [Ca(H2PO4)2], were added to rice straw feedstock at the ratio of 20% (w/w) for biochar formation through pyrolysis treatment, aiming to improve carbon retention and stabilization in biochar. Kaolin and CaCO3 had little effect on the carbon retention, whereas Ca(H2PO4)2 increased the carbon retention by up to 29% compared to untreated biochar. Although the carbon loss from the kaolin-modified biochar with hydrogen peroxide oxidation was enhanced, CaCO3 and Ca(H2PO4)2 modification reduced the carbon loss by 18.6 and 58.5%, respectively. Moreover, all three minerals reduced carbon loss of biochar with potassium dichromate oxidation from 0.3 to 38.8%. The microbial mineralization as CO2 emission in all three modified biochars was reduced by 22.2-88.7% under aerobic incubation and 5-61% under anaerobic incubation. Enhanced carbon retention and stability of biochar with mineral treatment might be caused by the enhanced formation of aromatic C, which was evidenced by cross-polarization magic angle spinning (13)C nuclear magnetic resonance spectra and Fourier transform infrared spectroscopy analysis. Our results indicated that the three minerals, especially Ca(H2PO4)2, were effective in increasing carbon retention and strengthening biochar stabilization, which provided a novel idea that people could explore and produce the designated biochar with high carbon sequestration capacity and stability.

In vitro anticoagulation monitoring of low-molecular-weight heparin

Institute of Scientific and Technical Information of China (English)

WANG Jian-qi; SHI Xu-bo; YANG Jin-gang; HU Da-yi

2009-01-01

Background Although low-molecular-weight heparin has replaced unfractionated heparin to become the primary anticoagulation drug for treatment of acute coronary syndrome, there is no convenient bedside monitoring method. We explored the best laboratory monitoring method of low-molecular-weight heparins (enoxapadn, dalteparin, and nadroparin) by use of the Sonoclot coagulation analyzer to monitor the activated clotting time.Methods Atotal of 20 healthy volunteers were selected and 15 ml of fasting venous blood samples were collected and incubated. Four coagulants, kaolin, diatomite, glass bead, and magnetic stick, were used to determine the activated clotting time of the low-molecular-weight heparins at different in vitro anti-Xa factor concentrations. A correlation analysis was made to obtain the regression equation. The activated clotting time of the different low-molecular-weight heparins with the same anti-Xa factor concentration was monitored when the coagulant glass beads were applied. Results The activated clotting time measured using the glass beads, diatomite, kaolin, and magnetic stick showed a linear correlation with the concentration of nadroparin (r= 0.964, 0.966, 0.970, and 0.947, respectively). The regression equation showed that the linear slopes of different coagulants were significantly different (glass beads 230.03 s/IU,diatomite 89.91 s/IU, kaolin 50.87 s/IU, magnetic stick could not be calculated). When the concentration of the anti-Xa factor was the same for different low-molecular-weight heparins, the measured activated clotting time was different after the application of the glass bead coagulant.Conclusions The glass bead coagulant is most feasible for monitoring the in vitro anticoagulation activity of nadroparin.The different effects of different low-molecular-weight heparins on the activated clotting time may be related to the different anti-Ila activities.

Author Details

African Journals Online (AJOL)

Aroke, U O. Vol 6, No 1 (2013) - Articles Fourier-transform Infrared Characterization of Kaolin, Granite, Bentonite and Barite Abstract PDF. ISSN: 1596-6035. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions ...

Author Details

African Journals Online (AJOL)

Dossou, Joseph. Vol 10, No 1 (2016) - Articles Influence des bulles gazeuses et des préparations fermentatives complexes sur la viscosité des mélasses de betterave à sucre. Abstract PDF · Vol 11, No 4 (2017) - Articles Bioefficacy of powdery formulations based on kaolin powder and cashew (Anacardium occidentale L.) ...

Discoloration of fired kaolinitic clays (Study of Fe+3 coordination by Mössbauer and UV-ViS-NIR spectroscopy)

Czech Academy of Sciences Publication Activity Database

Hanzlíček, Tomáš; Nižňanský, D.; Dědeček, Jiří; Steinerová, Michaela; Straka, Pavel; Třísková, J.

2007-01-01

Roč. 90, č. 9 (2007), s. 2843-2848 ISSN 0002-7820 R&D Projects: GA AV ČR IAA300460702 Institutional research plan: CEZ:AV0Z30460519; CEZ:AV0Z40400503 Keywords : kaolin * clay * Mössbauer spectroscopy Subject RIV: CA - Inorganic Chemistry Impact factor: 1.792, year: 2007 www.blackwell- synergy .com

75 FR 30370 - Certain Coated Paper Suitable For High-Quality Print Graphics Using Sheet-Fed Presses from the...

Science.gov (United States)

2010-06-01

... using sheet-fed presses; coated on one or both sides with kaolin (China or other clay), calcium... brightness level of 80 or higher;\\2\\ weighing not more than 340 grams per square meter; whether gloss grade... typically is referred to as [revaps]cover,' to distinguish it from [revaps]text.''' \\2\\ One of the key...

Acid Extraction - Ion Exchange Recovery of Cinchona Alkaloids Process and Plant Development

Science.gov (United States)

1945-06-08

center of the tank and dispersed by the rising jet from the bottom. From the operation of the scale model it was ascertained that the rate of...were then extracted from the precipitate by means of an alkali and an organic solvent« (18) Fink has suggested the use of a mixture of kaolin and

Clay pigment structure characterisation as a guide for provenance determination--a comparison between laboratory powder micro-XRD and synchrotron radiation XRD.

Science.gov (United States)

Švarcová, Silvie; Bezdička, Petr; Hradil, David; Hradilová, Janka; Žižak, Ivo

2011-01-01

Application of X-ray diffraction (XRD)-based techniques in the analysis of painted artworks is not only beneficial for indisputable identification of crystal constituents in colour layers, but it can also bring insight in material crystal structure, which can be affected by their geological formation, manufacturing procedure or secondary changes. This knowledge might be helpful for art historic evaluation of an artwork as well as for its conservation. By way of example of kaolinite, we show that classification of its crystal structure order based on XRD data is useful for estimation of its provenance. We found kaolinite in the preparation layer of a Gothic wall painting in a Czech church situated near Karlovy Vary, where there are important kaolin deposits. Comparing reference kaolin materials from eight various Czech deposits, we found that these can be differentiated just according to the kaolinite crystallinity. Within this study, we compared laboratory powder X-ray micro-diffraction (micro-XRD) with synchrotron radiation X-ray diffraction analysing the same real sample. We found that both techniques led to the same results.

White sand potentially suppresses radon emission from uranium tailings

Science.gov (United States)

Abdel Ghany, H. A.; El Aassy, Ibrahim E.; Ibrahim, Eman M.; Gamil, S. H.

2018-03-01

Uranium tailings represent a huge radioactive waste contaminant, where radon emanation is considered a major health hazard. Many trials have been conducted to minimize radon exhalation rate by using different covering materials. In the present work, three covering materials, commonly available in the local environment, (kaolin, white sand and bentonite) have been used with different thickness 10, 15, and 20 mm). 238U, 232Th, 40K and the radon exhalation rate were measured by using gamma spectrometry with a Hyper Pure Germanium (HPGe) detector and solid state nuclear track detectors (CR-39). Radon exhalation rate, calculated before and after covering, ranged from 2.80 ± 0.14 to 4.20 ± 0.21 Bq m-2 h-1, and from 0.30 ± 0.01 to 4.00 ± 0.20 Bq m-2 h-1, respectively. Also, the attenuation coefficients of different covering materials and radon emanation were calculated. The obtained results demonstrate that covering of uranium tailings by kaolin, white sand and bentonite has potentially minimized both the radon exhalation rate and the corresponding internal doses.

Role of particulates in subsurface migration of wastes

International Nuclear Information System (INIS)

Eichholz, G.G.; Craft, T.F.

1982-01-01

In contrast to the usual assumption that migration of radioactive wastes from deep repositories will occur primarily in the form of dissolved ions, subject to control by ion-exchange phenomena on exposed surfaces, an alternative mode of migration has been investigated by way of submicron-size suspended particles that act as carriers for leached waste atoms and travel relatively freely through water-bearing strata. Measurements have been conducted on adsorption on kaolin of Pu, Tc, Cs, Np and other tracer ions, with results strongly dependent on the nature of the water and its pH. Independently, column tests have been performed to study the movement of labelled kaolin suspensions through beds of sand, basalt, limestone and shale. For each medium, filter coefficients and sorption coefficients have been determined. For some bed materials the effluent suspensions displayed a prompt and a delayed component; the nature of the delay mechanism is not clearly understood at present. The investigations have shown that under certain conditions particulate migration may constitute a competitive pathway for waste motion. (author)

The magnetic fabrics of experimentally deformed artificial clay-water dispersions

Science.gov (United States)

Richter, Carl; Frisch, Wolfgang; Ratschbacher, Lothar; Schwarz, Hans-Ulrich

1991-12-01

The development of magnetic fabrics in artificial clay-water dispersions and natural, hematite-bearing mudstones is investigated in plane-strain pure shear laboratory experiments under strain rates of 1.6 × 10 -5 and 2 × 10 -4s-1. The mixtures contain 0,15, 30 and 45% chlorite in an illite matrix, and 0, 1, 3, 6 and 8% magnetite in a kaolin matrix. Shortening up to 40% is imposed. The resulting fabrics show the following characteristics: (1) In the clay mixtures, the principal susceptibility axes ( kmax ≥ kint ≥ kmin) rotate away from the well defined initial fabric orientations into the princip strain directions ( e1 ≥ e2 ≥ e3) at strains > 30%. (2) Both mineralogical composition and initial magnetic fabric, but not the applied strain, influence the magnitudes of the principal susceptibility axes. (3) The illite-chlorite mixture series show an almost linear correlation between mineral concentration and susceptibility magnitudes. (4) Magnetite dominates the fabric of the magnetite-kaolin mixtures; the fabric is independent of the magnetite concentration.

Evaluation of the effectiveness of the sealed double-ringed infiltrometers and the effects of changes in atmospheric pressure on hydraulic conductivity

International Nuclear Information System (INIS)

McMullin, S.R.

1994-01-01

The Savannah River Site (SRS) is currently evaluating some 40 hazardous and radioactive-waste sites for remediation. A remedial alternative under consideration is the closing of a waste site with a RCRA-style closure cap. The closure cap is a moisture barrier designed to inhibit the free flow of water downward into the buried wastes. When a remedial design is prepared, it is often necessary to test the cap materials to verify compliance with this recommended limit. Among the EPA-recommended test instruments is the sealed double-ring infiltrometer (SDRI). During recent testing at the Savannah River Site (SRS), six SDRI were installed and tested on a single kaolin clay cap. The purpose of this testing was to obtain a measure of the distribution of hydraulic conductivity across a model kaolin clay cap. The test results provide an evaluation of instrument performance and a measure of the repeatability of results. In addition, the testing identified variations in the unsaturated hydraulic conductivity. This paper presents an overview of the SDRI, the testing program at SRS, and an evaluation of the observations and test results

Coagulation mechanism of salt solution-extracted active component in Moringa oleifera seeds.

Science.gov (United States)

Okuda, T; Baes, A U; Nishijima, W; Okada, M

2001-03-01

This study focuses on the coagulation mechanism by the purified coagulant solution (MOC-SC-PC) with the coagulation active component extracted from M. oleifera seeds using salt solution. The addition of MOC-SC-PC tap water formed insoluble matters. This formation was responsible for kaolin coagulation. On the other hand, insoluble matters were not formed when the MOC-SC-PC was added into distilled water. The formation was affected by Ca2+ or other bivalent cations which may connect each molecule of the active coagulation component in MOC-SC-PC and form a net-like structure. The coagulation mechanism of MOC-SC-PC seemed to be an enmeshment of Kaolin by the insoluble matters with the net-like structure. In case of Ca2+ ion (bivalent cations), at least 0.2 mM was necessary for coagulation at 0.3 mgC l-1 dose of MOC-SC-PC. Other coagulation mechanisms like compression of double layer, interparticle bridging or charge neutralization were not responsible for the coagulation by MOC-SC-PC.

CERAMIC PROPERTIES OF PUGU KAOLIN CLAYS. PART I ...

African Journals Online (AJOL)

a

has indicated the presence of high levels of iron oxide (~ 1.43%) which could ..... attributed this increase in strength to the formation of a dense and thin layer close ... of the Non-metallic Minerals and the Silicate Industry in Tanzania, Kimambo, ...

Kaolinite-alunite association in late Gothic white grounds from Slovakia: A local peculiarity in painting technology

Czech Academy of Sciences Publication Activity Database

Hradil, David; Hradilová, J.; Bezdička, Petr; Matulková, I.

2017-01-01

Roč. 144, AUG (2017), s. 79-87 ISSN 0169-1317 R&D Projects: GA ČR(CZ) GA14-22984S Institutional support: RVO:61388980 Keywords : Alunite * Hydrothermal kaolin * Late-Gothic paintings * White earths * X-ray powder microdiffraction Subject RIV: CA - Inorganic Chemistry OBOR OECD: Inorganic and nuclear chemistry Impact factor: 3.101, year: 2016

High heat production granites of southwest England and their associated mineralization: a review

International Nuclear Information System (INIS)

Stone, M.; Exley, C.S.

1986-01-01

The structure of the exposed granites in Cornwall, Devon and the Scilly Isles and their geochemistry and mineralogy are described. The mineralization sequence, and the convective water circulation resulting from the presence of radioactive minerals are discussed. It is suggest that kaolinization and the redistribution of minerals are continuing because of the deep source of heat. (UK)

Mixed Waste Management Facility (MWMF) closure, Savannah River Plant: Clay cap test section construction report

Energy Technology Data Exchange (ETDEWEB)

1988-02-26

This report contains appendices 3 through 6 for the Clay Cap Test Section Construction Report for the Mixed Waste Management Facility (MWMF) closure at the Savannah River Plant. The Clay Cap Test Program was conducted to evaluate the source, lab. permeability, in-situ permeability, and compaction characteristics, representative of kaolin clays from the Aiken, South Carolina vicinity. (KJD)

Modelagem da retenção de herbicidas em zonas ripárias Modeling of herbicide retention in riparian zones

Directory of Open Access Journals (Sweden)

Alexandra P. de Pinho

2006-12-01

Full Text Available O presente trabalho teve como objetivo investigar a retenção de atrazina e picloram, transportados via escoamento superficial, em zona ripária. Para isto, simulou-se um escoamento superficial, contendo uma mistura de caulinita, atrazina e picloram, dentro de zonas ripárias estabelecidas ao longo de plantações de pinheiros do Nordeste do Estado da Geórgia, EUA. Cinco parcelas foram instaladas dentro de zonas ripárias, apresentando declividades diferentes (2, 5, 10, 15 e 20%. Os efeitos da umidade do solo e da presença do horizonte O na retenção dos dois herbicidas foram avaliados. Um modelo exponencial, comumente utilizado na estimativa de redução da DBO e de nutrientes em tratamento por escoamento superficial, foi empregado na estimativa de redução de herbicidas e caulinita em zonas ripárias. O modelo possibilitou estimar com razoável precisão, a remoção de caulinita e atrazina da mistura em escoamento ao longo de zonas ripárias de 10 m de comprimento. Em geral, a declividade foi o parâmetro que apresentou melhor correlação com a retenção dos contaminantes presentes na mistura em escoamento na zona ripária. O horizonte O, mais espesso nas maiores declividades, favoreceu tanto a sedimentação da caulinita como a adsorção da atrazina.This work aimed to investigate the retention of atrazine and picloram, carried by surface flow, in riparian zones. The surface flow, containing a mixture of both herbicides and kaolin, was then simulated within riparian zones established in pine plantations in north-eastern Georgia, USA. Five plots were established within riparian zones, each with a different slope (2, 5, 10, 15 and 20%. The influence of the initial moisture and of the O horizon condition in herbicide retention was analyzed. An exponential model, commonly used for the estimate of biochemical demand of oxygen (BOD and nutrients attenuation in overland flow treatment, was used to estimate the attenuation of kaolin and

Electrokinetic remediation of a copper contaminated clay: 2-D experiments

Energy Technology Data Exchange (ETDEWEB)

Rodriguez Maroto, J.M.; Garcia Delgado, R.A.; Gomez Lahoz, C.; Garcia Herruzo, F. [Dept. de Ingenieria Quimica, Univ. de Malaga (Spain); Vereda Alonso, C. [Dept. de Ingenieria Quimica, Univ. de Malaga (Spain)]|[Inst. for Geologi and Geoteknik, Danmarks Tekniske Univ., Lyngby (Denmark)

2001-07-01

The in-situ electrokinetic soil remediation technique was used to clean-up a commercial standard kaolin that had been contaminated with copper. A number of experiments were carried out at a lab scale with the purpose of testing the performance of this technique in a 2 dimensional arrangement and establishing the base for future studies on the distribution of electrodes. (orig.)

Electrokinetic remediation of a copper contaminated soil - experiments and 1-D model

Energy Technology Data Exchange (ETDEWEB)

Vereda Alonso, C.; Hansen, H.K. [Inst. for Geologi and Geoteknik, Danmarks Tekniske Univ., Lyngby (Denmark); Gomez Lahoz, C.; Rodriguez Maroto, J.M. [Dept. de Ingenieria Quimica, Univ. de Malaga (Spain)

2001-07-01

In this work, a set of electrokinetic soil remediation experiments has been performed in a column containing a commercial standard kaolin that was previously contaminated with copper. The profile evolution of copper concentration and pH along the soil column was obtained from these experiments. A one-dimensional numerical model has been developed to simulate the experimental results obtained from these experiments. (orig.)

Metallic and Ceramic Material Development Research

Science.gov (United States)

2010-05-01

and (3) Meta- Kaolin ................94 38. Thermal Expansion Properties of the Cr2O3-ZrW2O8 Composite...were evaluated using X-ray diffraction (XRD), X-ray Fluorescence (XRF), SEM, and Energy Dispersive Spectroscopy (EDS) [16]. 3.1.5. Elastic and...oxidation product could be detected between uncoated and coated fibers using transmission electron microscopy and energy- dispersive spectroscopy

Report on the geological-geochemical research carried out within the area of geochemical anomaly P7, Vathyrema, Drama Department

International Nuclear Information System (INIS)

Stavropoulos, Athanasios.

1982-08-01

The investigated area covering about 30 km 2 is situated in the crystalline massive of Rhodope (north of Drama deparment, E. Macedonia) where granitoids constitute its main petrological type. The geological-geochemical and radiometric investigations carried out so far in the area have localized a large number of places with high values of γ-radiation (1.000 - 15.000 c/s), as well as high concentrations of uranium (50-500 ppm). The uranium mineralization within the zone of oxidation is expressed by the uranium mineral autunite, accompanied by intensive hematitization-limonitization and chloritization-kaolinization, and additionally by small spots and veinlets of pyrite and galena. It seems that tectonic control exists on the uranium mineralization, since most of the anomalous concentrations of uranium are sitting along mylonite zones rich in chlorite and kaolin. There have been discerned seven more anomalous part areas which will have to be covered by geochemical stream sediment sampling (phase 3), as well as geological mapping (scale 1:5.000). The results from the research conducted within the concerned anomaly lead us to the conclusion that this area is very promising and possibilities of localization of uranium payable concentrations are very high. (N.Ch.)

Synthesis of solid catalyst from egg shell waste and clay for biodiesel production

Science.gov (United States)

Setiadji, S.; Sundari, C. D. D.; Munir, M.; Fitriyah, S.

2018-05-01

Until now, energy consumption in Indonesia is almost entirely fulfilled by fossil fuels, thus, its availability will be limited and continue to decrease. To overcome these problems, development and utilization of renewable energy are required, one of which is biodiesel. Biodiesel can be prepared through transesterification reaction of vegetable oil using catalyst. In this research, a solid catalyst for biodiesel synthesis was prepared from chicken egg shell waste and clay. Optimization of the transesterification reaction of coconut (Cocos nucifera) oil to obtain biodiesel was also carried out. The formation of CaO/kaolin catalyst was confirmed based on the results of XRD and SEM-EDS. This catalyst is suitable for biodiesel synthesis from vegetable oils with lower FFA (free fatty acid) levels, i.e. coconut oil with FFA level of 0.18%. Based on FTIR result, FFA level and flame tests, it was found that biodiesel was successfully formed. Synthesis of biodiesel has the optimum conditions on reaction time of 16 hours and temperature of 64 °C, with oil: methanol ratio of 1: 15 and CaO/kaolin catalyst concentration of 0.9% in a reflux system.

The effects of bauxite, metakaolin, and porosity on the thermal properties of prepared Iraqi clays refractory mortars

Science.gov (United States)

Zaidan, Shihab A.; Omar, Mustafa H.

2018-05-01

One of the most important requirements for the manufacture of refractory mortars, especially those used in the construction of thermal systems (building or plastering), is the balance between thermal insulation properties and porosity. Where, increasing porosity of mortar to a large amount may be always undesirable, because the absorption of liquid and gases emitted from industrial system is decline the bonded with bricks and structural properties of mortars. Refractory mortars prepared from either fired bauxite or metakaolin clays with different percentages of kaolin (10, 20, 30, and 40 wt%). Bauxite rocks were fired at 1200 °C and metakaolin was obtained by firing kaolin up to 700 °C then crushed and grinded. Grog was added to mixture to reduce the shrinkage. Cylindrical specimens are prepared and then sintered at 1200 °C. All mixtures maintained a low thermal conductivity within the limits of thermal insulation material (less than 0.5 W/m K); it was done by controlling the porosity which reached a maximum value approximately 25%. The volumetric heat capacity and thermal diffusivity was ranged between (1-10 MJ/m3 K), (0.06-0.2 mm2/s), respectively.

Absorption correction factor in X-ray fluorescent quantitative analysis

International Nuclear Information System (INIS)

Pimjun, S.

1994-01-01

An experiment on absorption correction factor in X-ray fluorescent quantitative analysis were carried out. Standard samples were prepared from the mixture of Fe 2 O 3 and tapioca flour at various concentration of Fe 2 O 3 ranging from 5% to 25%. Unknown samples were kaolin containing 3.5% to-50% of Fe 2 O 3 Kaolin samples were diluted with tapioca flour in order to reduce the absorption of FeK α and make them easy to prepare. Pressed samples with 0.150 /cm 2 and 2.76 cm in diameter, were used in the experiment. Absorption correction factor is related to total mass absorption coefficient (χ) which varied with sample composition. In known sample, χ can be calculated by conveniently the formula. However in unknown sample, χ can be determined by Emission-Transmission method. It was found that the relationship between corrected FeK α intensity and contents of Fe 2 O 3 in these samples was linear. This result indicate that this correction factor can be used to adjust the accuracy of X-ray intensity. Therefore, this correction factor is essential in quantitative analysis of elements comprising in any sample by X-ray fluorescent technique

Pressureless sintering and gas flux properties of porous ceramic membranes for gas applications

Directory of Open Access Journals (Sweden)

David O. Obada

Full Text Available The preparation and characterization of kaolin based ceramic membranes using styrofoam (STY and sawdust (SD as pore formers have been prepared by mechano-chemical synthesis using pressureless sintering technique with porogen content between (0–20 wt% by die pressing. Pellets were fired at 1150 °C and soaking time of 4 h. The membranes cast as circular disks were subjected to characterization studies to evaluate the effect of the sintering temperature and pore former content on porosity, density, water absorption and mechanical strength. Obtained membranes show effective porosity with maximum at about 43 and 47% respectively for membranes formulated with styrofoam and sawdust porogens but with a slightly low mechanical strength that does not exceed 19 MPa. The resultant ceramic bodies show a fine porous structure which is mainly caused by the volatilization of the porogens. The fabricated membrane exhibited high N2 gas flux, hence, these membranes can be considered as efficient for potential application for gas separation by reason of the results shown in the gas flux tests. Keywords: Porosity, Pore formers, Kaolin, Physico-mechanical properties, Gas separation, Gas flux

GLASS FORMATION AND PROPERTIES OF CORDIERITE COMPOSITIONS FROM TALC-BASED NATURAL RAW MATERIALS WITH BORON OXIDE ADDITION

Directory of Open Access Journals (Sweden)

Esin GÜNAY

2010-12-01

Full Text Available In this study, the glass forming behaviour of cordierite compositions in MAS (MgO-Al2O3-SiO2 system with added B2O3 content up to 3% were studied by melting the natural raw materials such as; talc, kaolin, alumina and boric acid as the source of MgO, SiO2, Al2O3 and B2O3 respectively. XRD analysis revealed the glass formation. Optical properties of the glasses were measured using UV-VIS spectrophotometer and structural changes were monitored by using FT-IR spectrometer. Physical properties such as density, colour, thermal expansion coefficients and hardness were measured according to the standard test methods. Glasses with a green colour were produced and this was attributed to the Fe content in the glass up to 0.5% coming from talc and kaolin. The addition of B2O3 to the glasses increased the glass transition temperatures (Tg values and reduced the thermal expansion coefficient values of the glasses from 5.2226 to 5.0072ºCx10-6, for MAS-T-0 and MAS-T-3, respectively.

Binder effect on seashell structure

Science.gov (United States)

Kamarudin, Kamarul Azhar; Hatta, Mohamed Nasrul Mohamed; Baba, Noor Wahida Ab; Hussin, Rosniza; Ismail, Al Emran

2017-10-01

Self-protection or known as defensive covering can be alluded to something that can secure body, building, or vehicles from harm or assault. As the evolution going on, the material utilized as a part of plate armour continue changing, from steel, Kevlar, ceramic and the materials that can give better impact and benefit to the user. A study has been led to distinguish either seashell can be one of the fundamental source to produce protective material due to the properties of seashell that consist of calcium chloride. Seashell is crushed and chipped using variable speed rotor mill and is compressed into specimen shape followed the ASTM C1211-13. Three different samples is tested made from seashells that mix with three different binder i.e. water, kaolin and polyethylene glycol (PEG) each. The specimens then were sintered at elevated controlled temperature 400°C before run for three point bending test to determine their mechanical properties results. Result shows that specimen with water gives highest value for Young's modulus and ultimate strength compared to sample with binder of kaolin and PEG. This proved that seashell powder remain intact even at higher temperature.

A new inorganic-organic composite coagulant, consisting of polyferric sulphate (PFS) and polyacrylamide (PAA).

Science.gov (United States)

Moussas, P A; Zouboulis, A I

2009-08-01

Currently, research is focused on the synthesis of new composite coagulants, which are constituted of both inorganic and organic materials. In this paper, the development of relevant reagents was investigated, by combining the inorganic pre-polymerised iron-based coagulant Polyferric Sulphate (PFS) with an organic, non-ionic polymer (Polyacrylamide, PAA) under different PAA/Fe (mg/l) and OH/Fe molar ratios. Moreover, the new reagents were characterised in terms of typical properties, stability and morphological analysis (XRD, FTIR, SEM). Their coagulation performance, when treating low or high turbid kaolin-humic acid suspensions, was also investigated, whereas the applied coagulation mechanisms were discussed by using the Photometric Dispersion Analysis (PDA) analysis. The results show that the new coagulation reagents present improved properties, including increased effective polymer species concentration, and they exhibit very good stability. The respective tests using PDA confirmed that the predominant coagulation mechanism of PFS-PAA is the bridge formation mechanism. Coagulation experiments in low or high turbid kaolin-humic acid suspensions reveal that the novel composite reagent PFS-PAA exhibits better coagulation performance, when compared with simple PFS, in terms of zeta-potential reduction, turbidity and organic matter removal and residual iron concentration.

Improved Sustainability through Novel Water Management Strategies for Strawberry Transplant Establishment in Florida, United States

Directory of Open Access Journals (Sweden)

Emmanuel A. Torres-Quezada

2012-12-01

Full Text Available Establishing bare-root transplants in Florida, United States, is an inefficient water-consuming activity. Between 3500 and 5500 m3/ha are applied with sprinkler irrigation to lower temperatures around the transplant crown and aid early root development, but more than 97% of the water volume runs off the polyethylene-covered beds. Research has been conducted to evaluate the feasibility of producing containerized (plug short-day cultivar transplants under Florida conditions, the effect of continuous and intermittent low-volume sprinklers on transplant establishment and the use of kaolin clay to reduce stress on young transplants. Research results demonstrated that growers may have alternatives to reduce water use and pumping costs during strawberry transplant establishment by the following: (a plug transplants can be produced from mother plants from Florida’s subtropical weather without chilling conditioning and still be competitive in the winter market; (b using continuous and intermittent low-volume sprinkler irrigation saves between 16% and 33% of the water volumes for strawberry establishment; and (c using kaolin clay showed to be a low-cost (US$63/ha plus application costs investment to reduce irrigation volumes by at least 30%.

The preservation of a cadaver by a clay sealant: Implications for the disposal of nuclear fuel waste

International Nuclear Information System (INIS)

Lee, C.F.; Oscarson, D.W.; Cheung, S.C.H.

1986-01-01

This report documents a case history in which a cadaver and the associated burial objects were found well preserved after being buried for more than 2100 years in Southern China. The preservation is attributed to a layer of kaolin that surrounded the coffin and served as a barrier to water and air movement. The implications for the disposal of nuclear fuel waste are discussed

Development of Permeable Reactive Barriers (PRB) Using Edible Oils

Science.gov (United States)

2008-06-01

naturally occurring processes of advection and dispersion to bring the contaminants to the treatment barrier. A large scale approach would be to form a...process has been developed for distributing soybean oil as an oil-in-water emulsion consisting of small oil droplets dispersed in a continuous...Thiele Kaolin Company, Sandersville, Georgia) was added to certain materials to evaluate the effect of increasing clay content. Grain size

Silica Nanofiber Combat Hemostat (SINCH)

Science.gov (United States)

2008-10-13

1.5mg 0.6 65 205 High aspect ratio silica fibers (30um x 60nm) 9mg 0.63 58.9 140 Kaolin (TEG control) 0.2mg n/a 59.8 155 TiO2 high aspect ratio...high surface area to volume ratio and thus the material is difficult to handle in an uncontrolled environment. It is easily dispersed and is not easy

Multifaceted role of clay minerals in pharmaceuticals

OpenAIRE

Khurana, Inderpreet Singh; Kaur, Satvinder; Kaur, Harpreet; Khurana, Rajneet Kaur

2015-01-01

The desirable physical and physiochemical properties of clay minerals have led them to play a substantial role in pharmaceutical formulations. Clay minerals like kaolin, smectite and palygorskite-sepiolite are among the world's most valuable industrial minerals and of considerable importance. The elemental features of clay minerals which caused them to be used in pharmaceutical formulations are high specific area, sorption capacity, favorable rheological properties, chemical inertness, swelli...

O the Determination of the Complex Refractive Index of Powdered Materials in the 9 TO 11 Micrometer Spectral Region Utilizing AN Attenuated Total Reflectance Technique.

Science.gov (United States)

Gillespie, James Bryce

1982-03-01

A specific method of determining the complex refractive index of powdered materials using attenuated total reflectance (ATR) spectroscopy was investigated. A very precise laser/goniometric ATR system was assembled and applied to powdered samples of carbon blacks, graphite, kaolin clay, quartz, calcite, and sodalime glass beads. The reflectivity data fell into two categories: (1) data representative of a medium having a unique effective refractive index and (2) data representative of a scattering medium having no unique refractive index. Data of the first kind were obtained from all the carbon black, graphite, and kaolin clay samples. The Fahrenfort-Visser solution of the Fresnel equations was applied to the goniometric reflectivity data for these samples to obtain the complex refractive index of these effective media. The complex refractive index obtained in this manner is not that of the bulk material but is instead a value which may be related to the bulk material value through some refractive index mixing rule. A systematic experiment using carbon black of particle size 0.0106 mm diameter was conducted to determine the applicability of several mixture rules for the volume packing fraction range of .2 to .6 which is most often encountered. The Bruggemann effective medium theory produced credible results while the Lorentz-Lorenz rule and the empirical Biot-Arago rule were invalid in this volume packing region. The Bruggemann rule was applied to lampblack, Mogul-L carbon black, graphite, and kaolin clay to obtain the complex refractive indices of these materials from the ATR spectroscopy data. Goniometric reflectivity data representative of an inhomogeneous scattering medium were obtained from all the powdered quartz, powdered calcite, and sodalime glass beads samples. These samples all contained particles with diameters nearly as large as the wavelength. These data demonstrate that the ATR technique, coupled with an effective medium analysis, may be used to obtain

Comportamiento coloidal de un caolín deshidratado

Directory of Open Access Journals (Sweden)

Ferrari, B.

2000-04-01

Full Text Available Short range attractive forces between particles can be developed by controlling the surface chemistry of particles in slurries. One method is to add salt to a dispersed slurry, which not only increases the slurry viscosity, but also imparts desirable plasticity to a consolidated powder compact. Consolidated kaolin is sufficiently plastic without further changes in chemistry, but for applications where a high relative density and dimensional control are needed, the elimination of water during drying and from the kaolin itself can produce cracks. For such applications, the use of a dehydrated kaolin is preferred. In this work, conditions for dispersing dehydrated kaolin are studied by using either an electrostatic deflocculant (TMAH or a polyelectrolyte (PAA that provides an electrosteric repulsive network between particles. Rheological properties of slips prepared from as-received and ball milled powders are studied as a function of the dispersant concentration and the solids loading. Optimal dispersing conditions have been identified and salt has been added to develope a weakly attractive particles network to produce plastic consolidated bodies. The effect of the added salt on the rheological properties of the slurries and consolidated bodies are reported.

El control coloidal de suspensiones permite desarrollar fuerzas atractivas de corto alcance entre partículas, a partir de las cuales se puede aumentar la viscosidad de una suspensión estable hasta proporcionarle la plasticidad deseada. Las suspensiones de caolín poseen elevada plasticidad, pero en aplicaciones que requieren una elevada densidad y control dimensional, la extracción del agua durante el secado y deshidroxilación puede originar grietas y defectos como consecuencia de la elevada contracción. En aplicaciones de este tipo se prefiere utilizar un caolín deshidratado, lo que supone la pérdida de plasticidad. En este trabajo se parte de un caolín deshidratado, con el

Bioefficacy of powdery formulations based on kaolin powder and ...

African Journals Online (AJOL)

extracts had less seeds damaged than hot extracts. F1 progeny decreased with ... reported that the use of chemical insecticides have a high ... uncontrolled chemicals insecticides use for preservation of ...... (Neem) as a model. Insecticides- ...

Physico-chemistry of continental Bentonites and Kaolin for ceramic ...

African Journals Online (AJOL)

... and the SSA values were between 4 m2g-1 and 19 m2g-1. Raw clay color ranged from white to black with most samples having a greyish-like appearance. These values are in conformity with those obtained by other researchers, and based on their physico-chemical characteristics, the clayey materials were found to be ...

Quantifying Life-Cycle Environmental Footprints of Soil and Groundwater Remedies

Science.gov (United States)

2013-07-01

background system: Emulsion polymerisation: In this process, surfactants (soaps) are used to disperse the vinyl chloride monomer in water. The monomer is...chloride is insoluble in water and disperses to fine droplets when mechanically agitated. The droplets remain in suspension as long as the agitation...from foreign substances such as wood, kaolin , coal, metal etc. in various washing stages. It is then sorted by size in vibration sieves or in an

Rapid Stabilization/Polymerization of Wet Clay Soils; Literature Review

Science.gov (United States)

2009-01-15

MacDonald, W. A., Pitman, D., and Ryan, T. G. (1999). "High Tempera- ture Non-aqueous Dispersion Polymerization of Aromatic Main Chain Liquid...of Dispersive Soils by Using Different Additives." Indian Geotechnical Journal, 14(3), 202-216. 36. Charleson, D. A. and Widger, R. A. (1989...Baghdadi, Z. A., and Khan, A. M. (1991). "Overconsolidated Beha- vior of Phosphoric Acid and Lime-Stabilized Kaolin Clay." Transportation Research

Thermophysical Properties of Matter - The TPRC Data Series. Volume 8. Thermal Radiative Properties - Nonmetallic Solids

Science.gov (United States)

1972-01-01

Iron oxldes- kaolin -aagneslum oxides- manganese oxldes-marble-nlckel oxldes-obsldlan-opal-opal glass-plexlglas- mylar—polyethylene-pyrocerams—quarts...34Dielectric Dispersion of Some Perovskite Zirconates," Phys. Rev. , A138(5), 1537-8, 1965. Loferski, J. J., "Infra-Red Optical Properties of Single...1), 131-40, 1967. Perry, C. H., "Far-Infrared Reflectance Spectra and Dielectric Dispersion of a Variety of Materials Having the Perovskite and

Preliminary Tests of Gloss-Reduction and Coloring Agents for Camouflage of Polyvinyl Acetate Dust-Control Film

Science.gov (United States)

1976-02-01

extenders Kaolin powder Calcium carbonate dust Paint flatteners Celite h99 Nytal 1+00 Dry pigments Chalk dust (various colors) Liquid...a dispersant or wetting agent for satisfactory mixing. Vor this purpose, one of two agents was used: (a) a commercial 10 per- cent determent...pockets of unmixed powder, and in some cases the powder settled to the bottom of the mold. The dispersants that were tried did not effectively disperse

Size Distribution, Chemical Composition and Optical Properties of Atmospheric Dust in Israel: A Comparison of Urban and Desert Aerosols under Clear and Dusty Conditions.

Science.gov (United States)

1980-02-01

counter (Royco 220). The instrument was calibrated with dry Latex particles of known sizes which were dispersed from a liquid suspension by the use of an...such spectra it is clear that samples from both sites contain significant amounts of gypsum, clay minerals, notably kaolin and montmorillonite clays...using a wavelength dispersive micro- probe. A comparison between aerosols from the Negev desert and Tel Aviv (under easterly flow) was conducted

Instrumentation Engineers Handbook

Science.gov (United States)

2013-01-01

dispersed , and is in the form of air slugs or large air bubbles the size of the electrode, the output signal will be noisy or even disrupted...to differentiate between the phases. Wet, low-quality steam is one such application; the liquid phase should be homogeneously dispersed within the...or kaolin slurries. These applications fail because highly absorbent solids attenuate the signal below that of usable strength. Lower frequency

The effect of Soil Temperature on Electrodialytic Remediation

DEFF Research Database (Denmark)

Kristensen, Iben Vernegren

1999-01-01

The electrodialytic remediation of copper, zinc and lead contaminated kaolin was studied at three different temperatures (0-39 degrees centrigrate). It is shown that an increase in temperature increases the rate of remediation for all three metals. Copper and zinc shows similar rate constants......, while for lead, the rate constant obtained are significantly smaller. The increased remediation rate is presumed to be due mainly to the lowering of the viscosity....

Development of Composite PCMs by Incorporation of Paraffin into Various Building Materials

Directory of Open Access Journals (Sweden)

Shazim Ali Memon

2015-02-01

Full Text Available In this research, we focused on the development of composite phase-change materials (CPCMs by incorporation of a paraffin through vacuum impregnation in widely used building materials (Kaolin and ground granulated blast-furnace slag (GGBS. The composite PCMs were characterized using environmental scanning electron microscopy (ESEM, Fourier transform infrared spectroscopy (FT-IR, differential scanning calorimetry (DSC and thermogravimetric analysis (TGA techniques. Moreover, thermal performance of cement paste composite PCM panels was evaluated using a self-designed heating system. Test results showed that the maximum percentage of paraffin retained by Kaolin and GGBS was found to be 18% and 9%, respectively. FT-IR results show that CPCMs are chemically compatible. The phase-change temperatures of CPCMs were in the human comfort zone, and they possessed considerable latent-heat storage capacity. TGA results showed that CPCMs are thermally stable, and they did not show any sign of degradation below 150 °C. From thermal cycling tests, it was revealed that the CPCMs are thermally reliable. Thermal performance tests showed that in comparison to the control room model, the room models prepared with CPCMs reduced both the temperature fluctuations and maximum indoor center temperature. Therefore, the prepared CPCMs have some potential in reducing peak loads in buildings when applied to building facade.

Novel approach on the risk assessment of oxidized fats and oils for perspectives of food safety and quality. I. Oxidized fats and oils induces neurotoxicity relating pica behavior and hypoactivity.

Science.gov (United States)

Gotoh, N; Watanabe, H; Osato, R; Inagaki, K; Iwasawa, A; Wada, S

2006-04-01

Food poisoning caused by deteriorated fat and oil in instant noodles was first reported in Japan approximately 40 years ago. In these cases, many people developed neurotoxic symptoms such as emesis and discomfort. The degree of oxidation of the fat and oil in the instant noodles that induced food poisoning was at least 100 meq/kg in peroxide value (PV). No general toxicity studies with animals, however, have examined the toxicity of fat and oil oxidized to that extent. In this study, pica behavior, a behavior characterized by eating a nonfood material such as kaolin and that relates to the degree of discomfort in animals, and alterations of locomotor activity of rats eating deteriorated fat and oil were measured. The groups fed fat and oil with at least 138.5 meq/kg PV consumed significantly more kaolin compared to the control group. Furthermore, rats that ate deteriorated fat and oil with at least 107.2 meq/kg PV had significantly decreased locomotor activity compared to control rats. These phenomena suggest that oxidized fat and oil with at least 100 meq/kg PV induce neurotoxicity. The toxicity of oxidized fat and oil has only been addressed using general toxicity tests, but the present results reveal the importance of evaluating toxicity by using other measures.

Modeling of flash calcination process during clay activation

International Nuclear Information System (INIS)

Borrajo Perez, Ruben; Gonzalez Bayon, Juan Jose; Sanchez Rodriguez, Andy A.

2011-01-01

Pozzolanic activity in some materials can be increased by means of different processes, among them, thermal activation is one of the most promising. The activation process, occurring at high temperatures and velocities produces a material with better characteristics. In the last few years, high reactivity pozzolan during cure's early days has been produced. Temperature is an important parameter in the activation process and as a consequence, the activation units must consider temperature variation to allow the use of different raw materials, each one of them with different characteristics. Considering the high prices of Kaolin in the market, new materials are being tested, the clayey soil, which after a sedimentation process produces a clay that has turned out to be a suitable raw material, when the kinetics of the pozzolanic reaction is considered. Additionally, other material with higher levels of kaolin are being used with good results. This paper is about the modeling of thermal, hydrodynamics and dehydroxilation processes suffering for solids particles exposed to a hot gas stream. The models employed are discussed; the velocity and temperature of particles are obtained as a function of carrier gas parameters. The calculation include the heat losses and finally the model predict the residence time needed for finish the activation process. (author)

Study on adsorption of 60Co in soils and minerals and transportation of 60Co in bean-soil system

International Nuclear Information System (INIS)

Feng Yonghong; Chen Chuanqun; Wang Shouxiang; Zhang Yongxi; Sun Zhiming

1998-02-01

The adsorption and desorption of 60 Co in soils and minerals, and the transportation, accumulation, distribution in bean-soil system are studied. The results are as follows: (1) 60 Co was adsorbed rapidly and desorbed difficultly by soils and minerals. The order of the saturated adsorption rate and K d (distribution coefficient) of 60 Co at the balance value was: kieselguhr>paddy soil (loamy clay)>yellowish red soil>kaoline>perlite>silt-loamy soil. The order of D f (desorption factor) value was: yellowish red soil>silt-loamy soil>kaoline>perlite>paddy soil (loamy clay)>kieselguhr. The dynamic behavior of 60 Co in the soils and minerals could be described as a closed two--compartment model. (2) After 60 Co was introduced to the bean-soil system, the concentration of 60 Co in the root is about 10.4∼23.3 times of that in the stalk, and 30 times of that in the bean pod. The negative correlation between the concentration of 60 Co in the soil and depth was detected, over 90 per cent of 60 Co was retained within 6 centimeters of the surface layer, the half residual depth was 2 centimeters. An opened two-compartment model was applied to describe the behavior of 60 Co in the bean-soil system

Uranium deposits associated to tertiary acid volcanism of the Pena Blanca Sierra (Chihuahua, Mexico)

International Nuclear Information System (INIS)

Aniel, B.

1986-12-01

The uraniferous deposits located in the Sierra de Pena Blanca (Chihuahua, Mexico) are the consequence of successive events that modified acid volcanic rocks. The devitrification of the Nopal Formation, vitroclastic tuffs, is esential in the cooling history because it releases uranium that becomes available. The uranium present in fluids as uranylcarbonate complexes, precipitate along the lamellea of hematite (exsolutions of the ilmenites). The presence of sulfur causes the destabilization of the ilmenites with uranium oxide (pitchblende - titanium oxide - pyrite), the pseudomorph of magnetites (pitchblende - pyrite) and the transformation of hematite into pyrite. The silice coming from the kaolinization of feldspars recristallizes as microcristalline quartz so that the rock appears compact. Fractures cause the uplifting of the lower unit of Nopal formation. It has been altered to montmorillonite. A carbonatation of this tuff has been observed and these two types of alteration occur after kaolinization. The Escuadra formation overlies the Nopal formation. The deposition takes place on an eroded basement where a soil developed. The two formations will together undergo transformations due to the saturation level and the primary ore will be only oxidized or oxidized, transported and reconcentrated. Late and localized thermal activities have been observed and may be the result of tectonic movements occurring after the supergene modification [fr

Impact of stylolitization on diagenesis of a Lower Cretaceous carbonate reservoir from a giant oilfield, Abu Dhabi, United Arab Emirates

Science.gov (United States)

Paganoni, Matteo; Al Harthi, Amena; Morad, Daniel; Morad, Sadoon; Ceriani, Andrea; Mansurbeg, Howri; Al Suwaidi, Aisha; Al-Aasm, Ihsan S.; Ehrenberg, Stephen N.; Sirat, Manhal

2016-04-01

Bed-parallel stylolites are a widespread diagenetic feature in Lower Cretaceous limestone reservoirs, Abu Dhabi, United Arab Emirates (UAE). Diagenetic calcite, dolomite, kaolin and small amounts of pyrite, fluorite, anhydrite and sphalerite occur along and in the vicinity of the stylolites. Petrographic observations, negative δ18OVPDB, fluid inclusion microthermometry, and enrichment in 87Sr suggest that these cements have precipitated from hot basinal brines, which migrated along the stylolites and genetically related microfractures (tension gashes). Fluid migration was presumably related to lateral tectonic compression events related to the foreland basin formation. The low solubility of Al3 + in formation waters suggests that kaolin precipitation was linked to derivation of organic acids during organic matter maturation, probably in siliciclastic source rocks. The mass released from stylolitization was presumably re-precipitated as macro- and microcrystalline calcite cement in the host limestones. The flanks of the oilfield (water zone) display more frequent presence and higher amplitude of stylolites, lower porosity and permeability, higher homogenization temperatures and more radiogenic composition of carbonates compared to the crest (oil zone). This indicates that oil emplacement retards diagenesis. This study demonstrates that stylolitization plays a crucial role in fluid flow and diagenesis of carbonate reservoirs during basin evolution.

Misconceptions regarding the pathogenicity of silicas and silicates.

Science.gov (United States)

Feigin, D S

1989-01-01

Several inhaled substances, from occupational or other environmental exposure, produce significant pulmonary disease and abnormalities demonstrated by pulmonary imaging. Areas of controversy and misconception relate principally to the extent and nature of both the clinical disease and the imaging abnormalities specific to each substance. The size and shape of the inhaled particles is an important determinant of the nature and severity of the disease produced, with fibrous shapes usually being the most pathogenetic. Fibrogenicity is another important pathogenetic characteristic of talc and kaolin, as well as asbestos. Talc produces four distinct forms of pulmonary disease, depending not only on the other substances with which it is inhaled, but also whether it is inhaled or injected intravenously. When inhaled alone, talc does not appear to produce significant pulmonary fibrosis or malignancy. Kaolin, mica, fuller's earth, zeolite, and fiberglass all vary in disease production according to their shape and fibrogenicity. Silica, diatomaceous earth, and other forms of silica are all highly fibrogenic and thus produce clinically obvious disease with sufficient inhalation. The largest particles usually produce nodular patterns in the upper pulmonary fields, as is typical of silicosis. The fibrous particles are more likely to manifest themselves as interstitial patterns in the lower pulmonary fields.

One-step green synthesis of non-hazardous dicarboxyl cellulose flocculant and its flocculation activity evaluation

International Nuclear Information System (INIS)

Zhu, Hangcheng; Zhang, Yong; Yang, Xiaogang; Liu, Hongyi; Shao, Lan; Zhang, Xiumei; Yao, Juming

2015-01-01

The waste management of used flocculants is a thorny issue in the field of wastewater treatment. To natural cellulose based flocculants, utilization of hazardous cellulose solvent and simplification of synthetic procedure are the two urgent problems needing to be further improved. In this work, a series of natural dicarboxyl cellulose flocculants (DCCs) were one-step synthesized via Schiff-base route. The cellulose solvent (NaOH/Urea solution) was utilized during the synthesis process. The full-biodegradable flocculants avoid causing secondary pollution to environment. The chemical structure and solution property of the DCC products were characterized by FT-IR, 1 H NMR, 13 C NMR, TGA, FESEM, charge density and ζ-potential. Kaolin suspension and effluent from paper mill were selected to evaluate the flocculation activity of the DCCs. Their flocculation performance was compared with that of commercial cationic polyacrylamide and poly aluminium chloride flocculants. The positive results showed that the NaOH/Urea solvent effectively promoted the dialdehyde cellulose (DAC) conversion to DCC in the one-step synthesis reaction. The DCCs with the carboxylate content more than 1 mmol/g exhibited steady flocculation performance to kaolin suspension in the broad pH range from 4 to 10. Its flocculation capacity to the effluent from paper mill also showed excellent

Development of Nanofluids as Lubricant to Study Friction and Wear Behavior of Stainless Steels

Science.gov (United States)

Sahoo, Rashmi Ranjan; Bhattacharjee, Santu; Das, Tuhin

A number of nanofluids have been prepared to study the effect of lubrication properties of nanofluids on stainless steels taking Kaolin and Boron Nitride (BN) as the lubricant particles and Sodium Dodecyl Sulfate (SDS), Cetyl Trimethyl Ammonium Bromide (CTAB), Sodium Hexa Meta Phosphate (SHMP) as dispersants in the same liquid medium i.e. water. A pin on disc tribometer is being used to access the tribological behaviour of the prepared nanofluids. The particle size of these particle dispersions are examined with a nanoparticle size analyzer. It has been found that the use of dispersants significantly control the particle size and tribological behavior of the nanofluids as for Boron Nitride particle with Sodium Dodecyl Sulfate (SDS) as dispersant has got a very low value of coefficient of friction being equal to 0.142 while without dispersant the value is 0.498. Similarly, in case of Kaolin water with SDS as dispersant the value of coefficient of friction obtained is 0.161 and without dispersant it is 0.333. Sodium Dodecyl Sulfate (SDS) as dispersant has resulted a very low coefficient of friction compared to other dispersants tested even though it doesn’t always assure a least particle size. The role of SDS in yielding the lowest friction has pursued significant attention for further investigation.

Bioflocculation production from lower-molecular fatty acids as a novel strategy for utilization of sludge digestion liquor.

Science.gov (United States)

Fujita, M; Ike, M; Jang, J H; Kim, S M; Hirao, T

2001-01-01

We propose the bioproduction of a bioflocculant from lower-molecular fatty acids as an innovative strategy for utilizing waste sludge digestion liquor. Fundamental studies on the production, characterization and application of a novel bioflocculant were performed. Citrobactersp. TKF04 was screened out of 1,564 natural isolates as a bacterial strain capable of a bioflocculant from acetic and propionic acids. TKF04 produced the bioflocculant during the logarithmic growth in the batch cultivation, and it could be recovered from the culture supernatant by ethanol precipitation. The fed-batch cultivation with feeding of acetic acid: ammonium 10;1 (mole) to maintain pH 8.5 led to the hyper-production of the bioflocculant. The bioflocculant was found to be effective for flocculating a kaolin suspension, when added at a final concentration of 1-10 mg/l, over a wide range of pHs (2-8) and temperatures (3-95 degrees C), while the addition of cations was not required. It could flocculate a variety of inorganic and organic suspended particles including kaolin, diatomite, bentonite, activated carbon, soil and activated sludge. These indicated that the bioflocculant possesses flocculating activity comparable or superior to that of synthetic flocculants. The bioflocculation was identified as a chitosan-like biopolymer.

Settling and sedimentation behavior of fine-grained materials

OpenAIRE

Nam, Sookie

2005-01-01

Channeling has already been an observed phenomenon that often occurs during settling and sedimentation processes of finer materials. However, it has been regarded as a minor factor affecting settling process, e.g. settling velocity or consolidation rate. In this study, settling behaviors of talcs, kaolins and attapulgite were reviewed by experiments with small and large settling columns with special focus on channel formation during sedimentation. The large settling column is equipped with tw...

Flexible and strong ternary blends of poly(vinyl chloride), poly(butylene adipate)and nanoparticle-plasticizers

OpenAIRE

Yin, Bo; Hakkarainen, Minna

2013-01-01

Multiple property enhancement was achieved for ternary blends of PVC, poly(butylene adipate) (PBA) plasticizer and PBA-grafted nanofillers as compared to ternary blends with untreated nanofillers. The blends with surface modified halloysite, kaolin or silicon dioxide nanofillers all exhibited higher stress at break and higher strain at break as compared to the corresponding composites with untreated nanoparticles. The strain at break was similar or improved compared to binary PVC/PBA blends. ...

Solid State Research

Science.gov (United States)

1975-04-17

D = n — n is the dispersion , and B = n — n is the birefringence. Differentiation of Eq. (II-l) gives 60j = | tan9j...than the measured value; therefore, the change in bi- refringence must be canceled partially by a change in dispersion . The type I room...chromel-alumel ther- mocouple that was mounted on the substrate surface with kaolin -sodium silicate paste and pro- tected from RF interference by

EFFECT OF DEXTRAN-graft-POLYACRYLAMIDE INTERNAL STRUCTURE ON FLOCCULATION PROCESS PARAMETERS

International Nuclear Information System (INIS)

Bezugla, T.; Kutsevol, N.; Shyichuk, A.; Ziolkowska, D.

2008-01-01

Dextran-graft-Polyacrylamide copolymers (D-g-PAA) of brush-like architecture were tested as flocculation aids in the model kaolin suspensions. Due to expanded conformation the D-g-PAA copolymers are more effective flocculants than individual PAA with close molecular mass. The internal structure of D-g-PAA copolymers which is determined by number and length of grafted PAA chains, the distance between grafts, etc., has the significant influence on flocculation behavior of such polymers

Alumina Coating To Realize Desired Pore Characteristics Of Sintered Diatomite Membrane

Directory of Open Access Journals (Sweden)

Ha J.-H.

2015-06-01

Full Text Available Porous ceramic membranes prepared from natural materials such as diatomite, have lately attracted great interest in industrial applications due to their cost-effectiveness. In this study, we attempted to prepare an alumina coating to be deposited over a sintered diatomite-kaolin composite support layer in order to reduce the largest pore size to below 0.4 μm; such a coating could be potentially used in water treatment applications for bacterial removal.

Leakage Current Waveforms and Arcing Characteristics of Epoxy Resin for Outdoor Insulators under Clean and Salt Fogs

Directory of Open Access Journals (Sweden)

Suwarno

2008-05-01

Full Text Available Ceramic outdoor insulators have been used in high voltage transmission lines since long time ago. Due to superiority in their resistance to pollution, recently, polymeric outdoor insulators are widely used. Epoxy resin is one polymer which shows good properties for outdoor insulation. During service, outdoor insulators may severe a certain degree of pollution which may reduce their surface resistance. Leakage current (LC usually increase and degradation may take place. This paper reports experimental results on the leakage current waveforms and arcing characteristics of epoxy resin under clean and salt fog. The samples used are blocks of epoxy resin with dimension of 250 x 50 x 20 mm3. The samples were put in a test chamber with dimension of 900x900x1200 mm3 with controllable humidity and pollution conditions. Clean and salt fog were generated according to IEC 60-1 and 507. The arcing experiment was done with incline plane test in accordance with IEC 587. AC voltage in the range from 5 kV to 50 kV with frequency of 50 Hz was applied. The LC waveforms up to flash over were measured. The magnitudes as well as harmonic content of the LC were analyzed. The correlation between LC waveforms and dry band arching phenomenon was elaborated. Visual observation of the arc on the sample surfaces was observed using a video camera. Experimental results indicated that LC magnitude on clean samples was slightly affected by humidity (RH. However, under salt fog, RH greatly affected the LC magnitude. The flashover voltage of clean samples under salt fog reduced significantly for fog conductivity of more than 1.2 mS/cm. Kaolin-polluted samples under salt fog showed an Ohmic behaviour. The LC magnitude was high and a large discrepancy of LC magnitude was observed for high applied voltage of larger than 25 kV. The largest LC magnitude was observed on salt-kaolin polluted samples under clean fog at high RH. LC waveforms analysis indicated that in general LC waveforms

Viabilidade do uso de argilas cauliníticas do Quadrilátero Ferrífero para a indústria cerâmica Availability of the kaolin from Quadrilátero Ferrífero for the ceramic industry

Directory of Open Access Journals (Sweden)

M. G. Peralta-Sánchez

2011-09-01

Full Text Available Sete amostras compostas, representativas de três ocorrências de argila caulinítica do Quadrilátero Ferrífero, foram caracterizadas física, mineralógica e quimicamente visando seu uso na indústria cerâmica. Apesar da presença predominante de caulinita, variações nos teores de Fe2O3 entre 2 a 44%, refletidos pela presença de goethita e hematita, acarretam diferentes cores que variam entre branco (ACM e DB, amarelo (R5, vermelho amarelado (FS e vermelho (DV, R1 e AM. Corpos cerâmicos foram queimados a 900 e 1100 °C, sendo que as cores praticamente não mudaram após a queima. Entretanto, somente corpos feitos com DV e R1 cumpriram as especificações técnicas para cerâmica, não apresentando fraturas e atingindo altas resistências à compressão: 96,2 MPa e 64,2 MPa, respectivamente. Para as outras amostras foram testadas misturas com filito (F nas proporções de 5, 10, 15, 20 e 25% e queima a 900 e 1100 °C. Os melhores resultados dos corpos cerâmicos, com ausência de fraturas, resistências à compressão entre 69,15 e 29,6 MPa e que cumpriram as especificações técnicas, foram obtidos nas proporções: ACM+15F, DB+5F, R5+5F, FS+5F, AM+5F e queima a 900 ºC.Seven samples from three kaolin deposits of the Quadrilátero Ferrífero were characterized by physical, mineralogical and chemical analyses in order to determine their use in the ceramic industry. Despite the predominant presence of kaolinite, the variations in the Fe2O3 content from 2 to 44%, due to presence of goethite and hematite, resulted in different colors, namely: white (ACM and DB, yellow (R5, yellowed red (FS and red (DV, R1 and AM. Specimens were burned at 900 and 1100 °C and they almost didn't change color. However, only specimens made with DV and R1 samples reached the technical specifications for the ceramic industry, without fractures and with values of compression strength of 96.2 and 64.2 MPa, respectively. The other samples were made by mixing

Development of clay liquid detergent for Islamic cleansing and the stability study.

Science.gov (United States)

Angkatavanich, J; Dahlan, W; Nimmannit, U; Sriprasert, V; Sulongkood, N

2009-04-01

Clay liquid detergents (CLDs) were developed for cleansing religiously-prohibited dirt ('najis') according to Islamic law. Four types of clay were selected: marl, kaolin, bentonite and veegum. After product development trials, five CLD formulations with varying combinations of clays were qualified for stability testing. Three exaggerated temperature conditions were considered: 4 degrees C for 24 h, 50 degrees C for 7 days, and 40 degrees C for 1 month. The CLDs were also evaluated at 30, 60 and 90 days after production, while being stored at room temperature (RT30, RT60 and RT90). Physical and chemical characteristics including pH, colour, viscosity, surface tension, foam tests and sensory liking scores were evaluated. Our results showed that the kaolin-based formula, F2, had an optimal pH (closest to skin pH) of 5.08. The other formulas ranged from pH 6 to 8. Colour shades of the CLDs ranged from white, to creamy white, to mildly greenish-white. The foaming properties of the CLDs, the means +/- SD of foam heights at 0 and 5 min, using the Ross-Miles test, were 19.13 +/- 0.25 to 20.88 +/- 0.45 cm at RT90 and were comparable with those of commercial detergents. Foam stability of all CLDs was high, as shown from the foam heights between 0 and 5 min being not significantly different (P > 0.05). The surface tensions, means +/- SD, of CLD solutions were between 27.94 +/- 0.08 and 28.72 +/- 0.04 mN m(-1), which were slightly better than the surface tension of 29.08 +/- 0.04 mN m(-1) for sodium lauryl sulphate. There was a weak negative relationship between surface activity and foam height, based on the pooled data of the CLDs (R(2) = 0.209, P viscosity of four CLDs ranged from 16 317 to 49 036 mPa s. In conclusion, CLDs can be formulated with good stability. F2 (kaolin-based, with a white, creamy texture) was the best CLD formula. It had the highest surface activity, moderate lathering and pleasant physical appearance.

A Review of Tribological Sinks in Six Major Industries

Science.gov (United States)

1985-09-01

limestone𔃽’ Crushed and broken granite Construction sand and gravel^3’ Industrial sand^3’ Bentonite Fire clay Fuller’s earth Kaolin and...lubricant was intended to combat. In some shaft mining applications, the lubricant must be deliberately diluted with water to reduce fire hazards. This...belts. Monorail or overhead trams take many forms. The item is supported from or hung from two or more wheels on the monorail . The units may be self

The effect of various sintering temperature on used refractory towards its physical properties

Science.gov (United States)

Sudibyo; Wulandari, Y. R.; Amin, M.; Azhar

2018-01-01

The used magnesia refractory from the kiln of cement industry was successfully recycled to new refractory using Kaolin as an adhesive. In this work, the temperatures of sintering were varied from 1000°C to 1500°C. The result shows that the increment temperature effects in sintering process will enhance refractory physical properties such as bulk density, cold crushing strength or pressure strength and thermal conductivity. Meanwhile, the porosity was decreased as the increase of the sintering temperature.

JPRS Report, Latin America.

Science.gov (United States)

1987-07-20

34revolutionary Peronism" in a bid to force them into the school. But the people dispersed thanks to the provincial police, who did an outstanding job. Then...decisive year which it was not, with the opposi- tion’s immobility and dispersion , the ground seemed fertile. Without wasting any time, Pinochet...first joint-venture economic project with the signing here of a protocol providing for cooperation in the mining of kaolin and gold. Officials here

Engineering Design Handbook: Environmental Series. Part Three. Induced Environmental Factors

Science.gov (United States)

1976-01-20

environmental factors. Rain will wash many pollutants from the atmosphere or winds will disperse them; rain or humidity will sup- press sand and dust...atmosphere (Ref. 11). (4) Air movement. Air movement serves to disperse 2-55 AMCP 70G-117 pollutants throughout the atmosphere. Airspeed and...CaCCL MgC03 MgCO^ Pure clay, kaolin , china clay Al203-2Si02.2H20 sand or dust environment includes (1) concentration (count or weight), (2

synthesis of zeolite-a using kaolin samples from darazo, bauchi ...

African Journals Online (AJOL)

henry mgbemere

Characteristic OH, Al-OH, Si-OH and Si-O-Al bands were confirmed in both samples ... structure and properties of kaolinite, the main mineral ..... edges were obtained for the zeolite while an .... Kaolinite at 5 to 600 K"Clays and Clay Minerals,.

Synthesis of zeolite-A using kaolin samples from Darazo, Bauchi ...

African Journals Online (AJOL)

The X - ray diffraction patterns clearly show the presence of the characteristic peaks (12.35 and 24.88o ) of kaolinite with little quartz impurities. X - ray diffraction measurements (2Ɵ peaks at 7 – 18o and 21 – 35o ) and scanning electron micro graphs clearly show that zeolite - A crystals are produced. The microstructures of ...

Influence of Froth Height on Column Flotation of Kaolin Ore

Directory of Open Access Journals (Sweden)

Fernando Pita

2017-11-01

Full Text Available The influence of the froth height in the reverse flotation of kaolinitic ore was analyzed based on the recovery by entrainment and by true flotation of iron, titanium and manganese oxides (FeO, TiO2 and MnO. Also, the influence of the particle size in the drainage process was analyzed. The recovery by entrainment and by true flotation of the three oxides is inversely proportional to the froth height. The entrained particles are drained more easily in the froth phase than the floated particles since they are not attached to the bubbles. The recovery by entrainment and drainage of the entrained material is similar for the three oxides. However, the recovery by true flotation and drainage of the floated material is different for the three oxides. FeO has the lowest recovery, as a consequence of the minor contribution of its hydrophobic minerals, while MnO has the greatest recovery values. For the entrained material, the finest fraction is entrained more easily, but it is also drained more easily, meaning these particles have more mobility in the froth zone. For the true floated material, the finest fraction is drained more easily, indicating the greater mobility of these particles in the froth; however, the coarsest fraction is drained more easily than the two intermediate fractions, indicating the weaker attachment of the larger particles to the bubbles.

Interaction of kaolin containing ores with natrium and calcium chlorides

International Nuclear Information System (INIS)

Sokhibov, I.Sh.; Dadabaeva, G.; Mirzoev, B.; Safiev, H.; Boboev, Kh.E.

1997-01-01

The impact of different factors on ore agglomeration at presence of carbon activators CaCl 2 and NaCl 2 was studied. The impact of different factors on water and hydrochloric acid processing of obtained cake was studied as well. The temperature influence was studied at temperature range 600-1000 deg C during 90 min sintering. The obtained cakes were leached by water in acid medium and were used as coagulants for water purification from suspended matters.

Critical State of Sand Matrix Soils

Science.gov (United States)

Marto, Aminaton; Tan, Choy Soon; Makhtar, Ahmad Mahir; Kung Leong, Tiong

2014-01-01

The Critical State Soil Mechanic (CSSM) is a globally recognised framework while the critical states for sand and clay are both well established. Nevertheless, the development of the critical state of sand matrix soils is lacking. This paper discusses the development of critical state lines and corresponding critical state parameters for the investigated material, sand matrix soils using sand-kaolin mixtures. The output of this paper can be used as an interpretation framework for the research on liquefaction susceptibility of sand matrix soils in the future. The strain controlled triaxial test apparatus was used to provide the monotonic loading onto the reconstituted soil specimens. All tested soils were subjected to isotropic consolidation and sheared under undrained condition until critical state was ascertain. Based on the results of 32 test specimens, the critical state lines for eight different sand matrix soils were developed together with the corresponding values of critical state parameters, M, λ, and Γ. The range of the value of M, λ, and Γ is 0.803–0.998, 0.144–0.248, and 1.727–2.279, respectively. These values are comparable to the critical state parameters of river sand and kaolin clay. However, the relationship between fines percentages and these critical state parameters is too scattered to be correlated. PMID:24757417