WorldWideScience

Sample records for kairomone lure blend

  1. Blend chemistry and field attraction of commercial sex pheromone lures to grape berry moth (Lepidoptera: Tortricidae), and a nontarget tortricid in vineyards.

    Science.gov (United States)

    Jordan, T A; Zhang, A; Pfeiffer, D G

    2013-06-01

    Anecdotal reports by scientists and growers suggested commercial sex pheromone lures were ineffective with monitoring field populations of grape berry moth, Paralobesia viteana (Clemens), in vineyards. This study addressed the need to evaluate commercial sex pheromone lures for chemical purity and efficacy of attracting grape berry moth and a nontarget tortricid, the sumac moth, Episumus argutanus (Clemens). The percentage of chemical components from a set of eight lures from each manufacturer was found using gas chromatography-mass spectrometry and confirmed by chemical standards. No lures adhered to the 9:1 blend of (Z)-9-dodecenyl acetate (Z9-12:Ac) to (Z)-11-tetradecenyl acetate (Z11-14:Ac), though Suterra (9.1:1), ISCA (5.7:1), and Trécé (5.4:1) lures were closest. The Trécé lures contained ≍98 μg Z9-12:Ac, which is 3-51 times more than the other lures. The Suterra and ISCA lures were loaded with ≍29 and 33 μg Z9-12:Ac, and the Alpha Scents lures only contained ≍2 μg Z9-12:Ac. An antagonistic impurity, (E)-9-tetradecenyl acetate (E9-12:Ac), was found in all manufacturer lures at concentrations from 3.2 to 4.8%. Field attraction studies were done in summer 2010, and again in 2011, to evaluate commercial lures for their potential to attract P. viteana and E. argutanus in the presence of lures from other manufacturers. Separate experiments were established in two vineyards in Augusta County, VA, one with open and the other with wooded surroundings. In field experiments, Suterra lures detected P. viteana most often, Trécé lures detected more E. argutanus, and ISCA lures detected P. viteana in the open vineyard the least, while Alpha Scents lures were least attractive to E. argutanus in both environments. Fewer P. viteana were captured in the wooded versus open vineyard, which may limit the potential for sex pheromone monitoring of P. viteana in wooded vineyards.

  2. Do bacteria, not fish, produce 'fish kairomone'?

    NARCIS (Netherlands)

    Ringelberg, J.; Van Gool, E.

    1998-01-01

    Fish-associated chemicals enhance phototactic downward swimming in Daphnia. If perch were treated with the antibiotic ampicillin, this enhancement was significantly decreased. Therefore, not fish, but bacteria associated with fish, seem to produce this kairomone. [KEYWORDS: Diel vertical migration;

  3. Potential for Using Acetic Acid Plus Pear Ester Combination Lures to Monitor Codling Moth in an SIT Program

    Directory of Open Access Journals (Sweden)

    Gary J. R. Judd

    2016-11-01

    Full Text Available Studies were conducted in commercial apple orchards in British Columbia, Canada, to determine whether lures combining ethyl-(E,Z-2,4-decadienoate, pear ester (PE, with either acetic acid (AA or sex pheromone, (E,E-8,10-dodecadien-1-ol (codlemone, might improve monitoring of codling moth, Cydia pomonella (L., in an area-wide programme integrating sterile insect technology (SIT and mating disruption (MD. Catches of sterile and wild codling moths were compared in apple orchards receiving weekly delivery of sterile moths (1:1 sex ratio using white delta traps baited with either AA or PE alone, and in combination. Sterile and wild codling moths responded similarly to these kairomone lures. For each moth sex and type (sterile and wild, AA-PE lures were significantly more attractive than AA or PE alone. Bisexual catches with AA-PE lures were compared with those of commercial bisexual lures containing 3 mg of codlemone plus 3 mg of PE (Pherocon CM-DA Combo lure, Trécé Inc., Adair, OK, USA, and to catches of males with standard codlemone-loaded septa used in SIT (1 mg and MD (10 mg programmes, respectively. CM-DA lures caught the greatest number of sterile and wild male moths in orchards managed with SIT alone, or combined with MD, whereas AA-PE lures caught 2–3× more females than CM-DA lures under both management systems. Sterile to wild (S:W ratios for male versus female moths in catches with AA-PE lures were equivalent, whereas in the same orchards, male S:W ratios were significantly greater than female S:W ratios when measured with CM-DA lures. Male S:W ratios measured with CM-DA lures were similar to those with codlemone lures. CM-DA and codlemone lures appear to overestimate S:W ratios as measured by AA-PE lures, probably by attracting relatively more sterile males from long range. Using AA-PE lures to monitor codling moths in an SIT programme removes fewer functional sterile males and reduces the need for trap maintenance compared with using

  4. Of pheromones and kairomones: what receptors mediate innate emotional responses?

    Science.gov (United States)

    Fortes-Marco, Lluis; Lanuza, Enrique; Martinez-Garcia, Fernando

    2013-09-01

    Some chemicals elicit innate emotionally laden behavioral responses. Pheromones mediate sexual attraction, parental care or agonistic confrontation, whereas predators' kairomones elicit defensive behaviors in their preys. This essay explores the hypothesis that the detection of these semiochemicals relies on highly specific olfactory and/or vomeronasal receptors. The V1R, V2R, and formyl-peptide vomeronasal receptors bind their ligands in highly specific and sensitive way, thus being good candidates for pheromone- or kairomone-detectors (e.g., secreted and excreted proteins, peptides and lipophilic volatiles). The olfactory epithelium also expresses specific receptors, for example trace amine-associated receptors (TAAR) and guanylyl cyclase receptors (GC-D and other types), some of which bind kairomones and putative pheromones. However, most of the olfactory neurons express canonical olfactory receptors (ORs) that bind many ligands with different affinity, being not suitable for mediating responses to pheromones and kairomones. In this respect, trimethylthiazoline (TMT) is considered a fox-derived kairomone for mice and rats, but it seems to be detected by canonical ORs. Therefore, we have reassessed the kairomonal nature of TMT by analyzing the behavioral responses of outbred (CD1) and inbred mice (C57BL/J6) to TMT. Our results confirm that both mouse strains avoid TMT, which increases immobility in C57BL/J6, but not CD1 mice. However, mice of both strains sniff at TMT throughout the test and show no trace of TMT-induced contextual conditioning (immobility or avoidance). This suggests that TMT is not a kairomone but, similar to a loud noise, in high concentrations it induces aversion and stress as unspecific responses to a strong olfactory stimulation. Copyright © 2013 Wiley Periodicals, Inc.

  5. Interactions between predator kairomone and food level complicate the ecological interpretation of Daphnia laboratory results

    NARCIS (Netherlands)

    Weber, A.

    2001-01-01

    The effect of food concentration on the phenotypic response of life history traits to two predator kairomones war investigated in Daphnia. For the experiment, one clone of Daphnia galeata war used as the prey organism and solutions containing infochemicals (kairomones) of Chaoborus (phantom midge)

  6. Variation in copper effects on kairomone-mediated responses in Daphnia pulicaria.

    Science.gov (United States)

    DeMille, C M; Arnott, S E; Pyle, G G

    2016-04-01

    Chemical signals play an integral role in many predator-prey relationships but their effectiveness can be altered by environmental conditions. Prey species can detect predator kairomones, which induce anti-predator defenses. An example of this predator-prey relationship exists between Daphnia spp. and Chaoborus spp.; however, when living in water contaminated with low concentrations of copper (Cu) Daphnia can fail to respond to Chaoborus kairomone and, in turn, become more susceptible to predation. This has implications for Daphnia living in regions with Cu contamination, such as areas where mining activity has resulted in increased levels of metals in the surrounding lakes. We examined kairomone-mediated responses of multiple Daphnia pulicaria clones obtained from 8 lakes in Ontario, Canada, in the absence and presence of environmentally-relevant Cu concentrations. Life history traits and morphological anti-predator defenses were assessed using neonates collected from mothers that were exposed to kairomone and Cu treatments. We found that kairomone-mediated responses and Cu-tolerance varied among D. pulicaria clones. Clones exposed to kairomone, in the absence of Cu additions, had diverse responses, including larger neonates, delayed reproduction, or altered brood size relative to no-kairomone controls. These kairomone-induced responses act as antipredator defense strategies against Chaoborus by preventing predation or stabilizing population growth. When exposed to Cu, two clones were able to respond to kairomone, while four clones no longer induced a response to kairomone. This variation in non-lethal effects of Cu on aquatic organisms suggests that toxicity tests should incorporate multiple genotypes and include predator-prey interactions. Copyright © 2016 Elsevier Inc. All rights reserved.

  7. New features at the LURE-D22 SAXS beamline

    International Nuclear Information System (INIS)

    Lesieur, P.; Lombardo, D.; Beauchet, L; Creof, C.; Decamps, T.; Dubuisson, J.M.; Perilhous, G.

    1999-01-01

    The D22 beamline of the DCI storage ring at LURE is dedicated to the study of structural properties in the field of material science by way of the small-angle X ray scattering (SAXS) technique. The D2 bending magnet of the DCI ring offers a stable source of limited brilliance but long decay time (200 hours) so that the beam can be used up to 110 hours after an injection of the positrons in the ring. Two different settings respectively dedicated to metallurgy and soft matter share the beam time. The latter which is considered here mainly deals with ill condensed matter: non ideal solutions of amphiphiles or polymers, liquid crystals, colloids, gels, xerogels, aerogels. (author)

  8. Fish kairomones induce spine elongation and reduce predation in marine crab larvae.

    Science.gov (United States)

    Charpentier, Corie L; Wright, Alexander J; Cohen, Jonathan H

    2017-08-01

    Specialized defense strategies are induced in zooplankton upon detection of predator chemical cues or kairomones. These defenses are well-described for freshwater zooplankters, with morphological defenses being particularly striking, but few studies have reported kairomone-induced morphological defenses in marine zooplankton. Here, we compare morphological responses to kairomones in the larvae of two marine crab species, estuarine mud crabs (Rhithropanopeus harrisii) and Asian shore crabs (Hemigrapsus sanguineus). When reared in the presence of fish kairomones, spine length increased by 2-3% in larval R. harrisii, while no morphological changes were identified in H. sanguineus. In subsequent feeding assays with a co-occurring fish predator (Atlantic silversides, Menidia menidia), consumption of R. harrisii was lower on larvae that had been reared with kairomones. In addition, we found that broods with smaller larvae are more likely to exhibit increases in spine length after kairomone exposure. Hence, the observed morphological response is likely influenced by larval size. © 2017 by the Ecological Society of America.

  9. Luring anglers to enhance fisheries

    Science.gov (United States)

    Martin, Dustin R.; Pope, Kevin L.

    2011-01-01

    Current fisheries management is, unfortunately, reactive rather than proactive to changes in fishery characteristics. Furthermore, anglers do not act independently on waterbodies, and thus, fisheries are complex socio-ecological systems. Proactive management of these complex systems necessitates an approach-adaptive fisheries management-that allows learning to occur simultaneously with management. A promising area for implementation of adaptive fisheries management is the study of luring anglers to or from specific waterbodies to meet management goals. Purposeful manipulation of anglers, and its associated field of study, is nonexistent in past management. Evaluation of different management practices (i.e., hypotheses) through an iterative adaptive management process should include both a biological and sociological survey to address changes in fish populations and changes in angler satisfaction related to changes in management. We believe adaptive management is ideal for development and assessment of management strategies targeted at angler participation. Moreover these concepts and understandings should be applicable to other natural resource users such as hunters and hikers.

  10. ß-Phellandrene: Kairomone for Pine Engraver, Ips pini (Say) (Coleoptera: Scolytidae)

    Science.gov (United States)

    Daniel R. Miller; John H. Borden

    1990-01-01

    The responses of Ips pini (Scolytidae) to multiple-funnel traps baited with the pheromone, ipsdienol, and various monoterpenes were determined in stands of lodgepole pine in southern and central British Columbia. Ips pini was attracted to both ipsdienol and ß-phellandrene, demonstrating that ß-phellandrene is a kairomone for this...

  11. Prey preference of the phytoseiid mite Typhlodromus pyri. 1. Response to volatile kairomones.

    NARCIS (Netherlands)

    Dicke, M.

    1988-01-01

    Using a Y-tube olfactometer, a study has been made of the response of females of the predatory miteTyphlodromus pyri Scheuten (Acarina: Phytoseiidae) to volatile kairomones of three prey species: the European red spider mite (Panonychus ulmi (Koch)), the two-spotted spider mite (Tetranychus urticae

  12. Gene up-regulation in response to predator kairomones in the water flea, Daphnia pulex

    Directory of Open Access Journals (Sweden)

    Okada Yasukazu

    2010-04-01

    Full Text Available Abstract Background Numerous cases of predator-induced polyphenisms, in which alternate phenotypes are produced in response to extrinsic stimuli, have been reported in aquatic taxa to date. The genus Daphnia (Branchiopoda, Cladocera provides a model experimental system for the study of the developmental mechanisms and evolutionary processes associated with predator-induced polyphenisms. In D. pulex, juveniles form neckteeth in response to predatory kairomones released by Chaoborus larvae (Insecta, Diptera. Results Previous studies suggest that the timing of the sensitivity to kairomones in D. pulex can generally be divided into the embryonic and postembryonic developmental periods. We therefore examined which of the genes in the embryonic and first-instar juvenile stages exhibit different expression levels in the presence or absence of predator kairomones. Employing a candidate gene approach and identifying differentially-expressed genes revealed that the morphogenetic factors, Hox3, extradenticle and escargot, were up-regulated by kairomones in the postembryonic stage and may potentially be responsible for defense morph formation. In addition, the juvenile hormone pathway genes, JHAMT and Met, and the insulin signaling pathway genes, InR and IRS-1, were up-regulated in the first-instar stage. It is well known that these hormonal pathways are involved in physiological regulation following morphogenesis in many insect species. During the embryonic stage when morphotypes were determined, one of the novel genes identified by differential display was up-regulated, suggesting that this gene may be related to morphotype determination. Biological functions of the up-regulated genes are discussed in the context of defense morph formation. Conclusions It is suggested that, following the reception of kairomone signals, the identified genes are involved in a series of defensive phenotypic alterations and the production of a defensive phenotype.

  13. Kairomonal communication in mice is concentration-dependent with a proportional discrimination threshold [v2; ref status: indexed, http://f1000r.es/2h5

    Directory of Open Access Journals (Sweden)

    Anand Vasudevan

    2013-12-01

    Full Text Available Odors of predators are often co-opted by prey species to serve as warning signals. Perceptual properties of such kairomonal communication are under studied despite their common use in many mammals. We demonstrate that the kairomonal response in mice to rat odors varies monotonically with the volume of rat odor. Moreover, the ability of mice to differentiate between two strengths of rat odors is dependent on the ratio of the two concentrations. These results show that mice can compare kairomonal strength over a large range of values, and that kairomonal communication follows Weber’s law.

  14. Lack of spatial segregation in the representation of pheromones and kairomones in the mouse medial amygdala.

    Directory of Open Access Journals (Sweden)

    Vinicius Miessler de Andrade Carvalho

    2015-08-01

    Full Text Available The nervous system is organized to detect, internally represent and process sensory information to generate appropriate behaviors. Despite the crucial importance of odors that elicit instinctive behaviors, such as pheromones and kairomones, their neural representation remains little characterized in the mammalian brain. Here we used expression of the immediate early gene product c-Fos as a marker of neuronal activity to find that a wide range of pheromones and kairomones produces activation in the medial nucleus of the amygdala, a brain area anatomically connected with the olfactory sensory organs. We see that activity in this nucleus depends on vomeronasal organ input, and that distinct vomeronasal stimuli activate a dispersed ensemble of cells, without any apparent spatial segregation. This activity pattern does not reflect the chemical category of the stimuli, their valence or the induced behaviors. These findings will help build a complete understanding of how odor information is processed in the brain to generate instinctive behaviors.

  15. Insecticide resistance may enhance the response to a host-plant volatile kairomone for the codling moth, Cydia pomonella (L.)

    Science.gov (United States)

    Sauphanor, Benoît; Franck, Pierre; Lasnier, Thérèse; Toubon, Jean-François; Beslay, Dominique; Boivin, Thomas; Bouvier, Jean-Charles; Renou, Michel

    2007-06-01

    The behavioral and electroantennographic responses of Cydia pomonella (L.) to the ripe pear volatile ethyl (2 E,4 Z)-2,4-decadienoate (Et- E, Z-DD), were compared in insecticide-susceptible and -resistant populations originating from southern France. A dose-response relationship to this kairomonal attractant was established for antennal activity and did not reveal differences between susceptible and resistant strains. Conversely, males of the laboratory strains expressing metabolic [cytochrome P450-dependent mixed-function oxidases (mfo)] or physiological (kdr-type mutation of the sodium-channel gene) resistance mechanisms exhibited a significantly higher response to Et- E, Z-DD than those of the susceptible strain in a wind tunnel experiment. No response of the females to this kairomone could be obtained in our wind-tunnel conditions. In apple orchards, mfo-resistant male moths were captured at significantly higher rates in kairomone-baited traps than in traps baited with the sex pheromone of C. pomonella. Such a differential phenomenon was not verified for the kdr-resistant insects, which exhibited a similar response to both the sex pheromone and the kairomonal attractant in apple orchards. Considering the widespread distribution of metabolic resistance in European populations of C. pomonella and the enhanced behavioral response to Et- E, Z-DD in resistant moths, the development of control measures based on this kairomonal compound would be of great interest for the management of insecticide resistance in this species.

  16. Are light traps baited with kairomones effective in the capture of Lutzomyia longipalpis and Lutzomyia intermedia? An evaluation of synthetic human odor as an attractant for phlebotomine sand flies (Diptera: Psychodidae: Phlebotominae).

    Science.gov (United States)

    Andrade, Andrey J; Andrade, Mateus R; Dias, Edelberto S; Pinto, Mara C; Eiras, Alvaro E

    2008-06-01

    Phlebotomine sand flies are often captured with human bait and/or light traps, either with or without an animal bait. More recently, synthetic attractants have been used as bait in traps to improve the capture of phlebotomine sand flies as well as other insects of medical and veterinary importance. The aim of the present study was to evaluate the effects of the kairomone 1-octen-3-ol (octenol) and the synthetic human odor BG-Mesh Lure (BGML--lactic acid, caproic acid and ammonia) baited in modified CDC light traps on the capture of phlebotomine sand flies. The experiments followed the 5x5 Latin square design. Among the species caught, Lutzomyia intermedia apparently presented a dose-dependent response to octenol. The response obtained with the BGML, alone or in combination with octenol (5 mg/h), indicated some degree of attractiveness of these baits to different phlebotomine sand fly species. Octenol seems to be more attractive to L. intermedia than to Lutzomyia longipalpis, while the BGML presented a higher success in capturing L. longipalpis. When the components of the BGML were used separately, there was no increase in catching the female of L. intermedia. Apparently, there was no synergistic effect between the octenol and the BGML. In conclusion, the octenol and the BGML were demonstrated to be possible baits to attract some phlebotomine sand fly species.

  17. Decommissioning of the LURE Nuclear Facility

    International Nuclear Information System (INIS)

    Pauwels, N.; Horodynski, J.M.; Robert, P.; Tadjeddine, A.

    2013-01-01

    With the goal of obtaining the decommissioning of the LURE nuclear facility, three of its accelerators were dismantled and another was modified to be below the thresh- old of 'Installation Nucleaire de Base' status. Operations were carried out with the strategy of mechanical dismantling with no cutting process. As the civil engineering radioactivity level was low, a great majority of it has been left in place with no process- ing, but compensatory measures have been taken for public and environmental protection. The overall result of these operations is a gain in both cost and operating time. They also contribute to a significant decrease in the risks, including radiological ones. The radiological impact after decommissioning remains acceptable. (authors)

  18. Isolation and identification of volatile kairomone that affects acarine predator-prey interactions: involvement of host plant in its production.

    NARCIS (Netherlands)

    Dicke, M.; Beek, van T.A.; Posthumus, M.A.; Dom, Ben N.; Bokhoven, van H.; Groot, de Ae.

    1990-01-01

    A volatile kairomone emitted from lima bean plants (Phaseolus lunatus) infested with the spider miteTetranychus urticae, was collected on Tenax-TA and analyzed with GC-MS. Two components were identified as the methylene monoterpene (3E)-4,8-dimethyl-1,3,7-nonatriene and the methylene sesquiterpene

  19. Comparison of two synthetic food-odor lures for captures of feral Mexican fruit flies (Diptera: Tephritidae) in Mexico and implications regarding use of irradiated flies to assess lure efficacy.

    Science.gov (United States)

    Robacker, David C; Thomas, Donald B

    2007-08-01

    Feral Mexican fruit flies, Anastrepha ludens (Loew) (Diptera: Tephritidae), were trapped in a citrus orchard in Mexico by using two types of synthetic food-odor lures, the AFF lure (Anastrepha fruit fly lure, APTIV, Inc., Portland, OR) and the BioLure (two-component MFF lure, Suterra LLC, Inc., Bend, OR). In Multilure traps (Better World Manufacturing, Inc., Miami, FL) containing water, BioLures captured about the same numbers of flies as AFF lures. In Multilure traps containing antifreeze solution, BioLures captured 2 and 5 times more flies than AFF lures in two experiments. BioLures, and AFF lures did not differ in attractiveness when used on sticky traps (Intercept trap, APTIV, Inc.; and sticky cylinder trap). Multilure traps captured >4 times as many flies as sticky traps with the exception that captures of females did not differ between Multilure and sticky traps baited with AFF lures. The percentage of females captured in Multilure traps was greater when traps were baited with BioLures compared with AFF lures, but the reverse was true for sticky traps. Sticky cylinder traps captured a higher percentage of females than Multilure traps. The most effective trap/lure combination was the Multilure trap baited with BioLure and antifreeze. In comparison with tests of these two lures in Texas, results were similar for Multilure traps, but they differed for sticky cylinder traps in that AFF lures were consistently more attractive than BioLures in Texas, but not in Mexico.

  20. Business Lures Employed by Malay Kelantanese Entrepreneurs

    Directory of Open Access Journals (Sweden)

    Sahad Mohd Nizam

    2018-01-01

    Full Text Available The foundation of a successful business is essentially the level of consumer response to a product or service offered. Entrepreneurs’ abilitities to cater to their consumers’ needs are one of their secrets to success. Hence, the objective of this study is to uncover the secrets of business success, particularly the business lures that have helped Kelantan entrepreneurs to popularise products or services they offer. A qualitative approach was used to analyse the interview data according to themes. The study found five factors which determined the business success of the selected Malay Kelantanese entrepreneurs. These factors were: they were persistent in asking for help from Allah, they strived to be approachable entrepreneurs, and they cultivated positive entrepreneurial virtues such as having an honourable personality, being creative, and innovative, as well as being bold in their marketing strategy. Although the findings are not representative of all Malay entrepreneurs in Malaysia, this study can, however, serve as a source of reference to encourage other entrepreneurs to emulate the business success of the selected entrepreneurs. Apart from that, it can encourage awareness among the Muslim entrepreneurs, about the importance of managing a business in accordance with the Islamic laws

  1. Assessment of commercially available pheromone lures for monitoring diamondback moth (Lepidoptera: Plutellidae) in canola.

    Science.gov (United States)

    Evenden, M L; Gries, R

    2010-06-01

    Sex pheromone monitoring lures from five different commercial sources were compared for their attractiveness to male diamondback moth, Plutella xylostella L. (Lepidoptera: Plutellidae) in canola, Brassica napus L., fields in western Canada. Lures that had the highest pheromone release rate, as determined by aeration analyses in the laboratory, were the least attractive in field tests. Lures from all the commercial sources tested released more (Z)-11-hexadecenal than (Z)-11-hexadecenyl acetate and the most attractive lures released a significantly higher aldehyde to acetate ratio than less attractive lures. Traps baited with sex pheromone lures from APTIV Inc. (Portland, OR) and ConTech Enterprises Inc. (Delta, BC, Canada) consistently captured more male diamondback moths than traps baited with lures from the other sources tested. In two different lure longevity field trapping experiments, older lures were more attractive to male diamondback moths than fresh lures. Pheromone release from aged lures was constant at very low release rates. The most attractive commercially available sex pheromone lures tested attracted fewer diamondback moth males than calling virgin female moths suggesting that research on the development of a more attractive synthetic sex pheromone lure is warranted.

  2. Interactions between Ethanol, syn-2,3-Hexanediol, 3-Hydroxyhexan-2-one, and 3-Hydroxyoctan-2-one Lures on Trap Catches of Hardwood Longhorn Beetles in Southeastern United States.

    Science.gov (United States)

    Miller, D R; Crowe, C M; Mayo, P D; Reid, L S; Silk, P J; Sweeney, J D

    2017-10-01

    The effectiveness of a four-component "super lure" consisting of ethanol (E) and the cerambycid pheromones syn-2,3-hexanediol (D6), racemic 3-hydroxyhexan-2-one (K6), and racemic 3-hydroxyoctan-2-one (K8) on trap catches of Cerambycidae (Coleoptera) was determined in southeast United States with seven trapping experiments in 2011-2013. We captured 74 species of longhorn beetles in our three-year study. Ethanol significantly increased the mean catches of seven species and increased the number of cerambycid species detected. Traps with the "super lure" were effective for 8 of 13 species of Cerambycidae previously shown to be attracted to binary combinations of ethanol plus one of the three pheromones. However, the "super lure" was less effective for the remaining five species with catch reductions of 40-90% compared with combinations of ethanol and one or two of the pheromones. For example, K6 + K8 lures reduced catches of Anelaphus villosus (F.) in traps with E + D6 by 90%. Similarly, catches of Anelaphus pumilus (Newman) in traps with E + K6 + D6 were reduced by 50% with the addition of K8. Catches of Knulliana cincta (Drury) in traps with K6 + K8 lures were interrupted by D6, an effect negated by the addition of ethanol. Given the interruptive effects on trap catches of some species when lures are combined in a single trap, developing optimal lure blends to maximize detection efficacy will be a challenge for managers of detection programs for non-native invasive species of longhorn beetles. Published by Oxford University Press on behalf of Entomological Society of America 2017. This work is written by (a) US Government employee(s) and is in the public domain in the US.

  3. Chemical investigations of volatile kairomones produced by Hyphantria cunea (Drury), a host of the parasitoid Chouioia cunea Yang.

    Science.gov (United States)

    Zhu, G; Pan, L; Zhao, Y; Zhang, X; Wang, F; Yu, Y; Fan, W; Liu, Q; Zhang, S; Li, M

    2017-04-01

    In tritrophic 'plants-herbivores-natural enemies' systems, there are relatively few reports concerning the role(s) of kairomones in pupal parasitism. Chouioia cunea Yang (Hymenoptera: Eulophidae), an endoparasitic chalcid wasp, parasitizes pupae of the fall webworm (Hyphantria cunea Drury). The role of host-related kairomones was investigated using electroantennogram (EAG) and behavioral techniques. Chemicals from some host stages (pupae) and host by-products (frass), induced arrestment behavior of female parasitoids, while chemicals from prepupae, were inactive. Gas chromatography-mass spectrometry analysis of volatiles collected from pupae, frass and prepupae using solid-phase microextration revealed seven compounds with carbon chain lengths ranging from C4 to C20. All of the chemicals elicited significant EAG responses in C. cunea. Y-tube olfactometer bioassays demonstrated a significant positive response of mated female C. cunea to 1-dodecene. These data provide a better understanding of the host location mechanisms of pupal parasitoid.

  4. Efficacy of two synthetic food-odor lures for Mexican fruit flies (Diptera: Tephritidae) is determined by trap type.

    Science.gov (United States)

    Robacker, David C; Czokajlo, Darek

    2005-10-01

    Sterile mass-reared Mexican fruit flies, Anastrepha ludens (Loew), were trapped in a citrus orchard by using multilure traps and cylindrical sticky traps baited with Advanced Pheromone Technologies Anastrepha fruit fly (AFF) lures or Suterra BioLure two-component (ammonium acetate and putrescine) MFF lures (BioLures). The cylinder trap/AFF lure combination was the best trap over the first 6 wk, the multilure trap/BioLure combination was best during weeks 6-12, and the multilure trap/AFF lure combination was best during the last 6 wk. The multilure trap/BioLure combination was best overall by 36% over the cylinder trap/AFF lure combination, and 57% over the multilure trap/AFF lure combination. Cylinder traps with BioLures were the least effective trap/lure combination throughout the experiment, capturing only half as many flies as cylinder traps with AFF lures. Captures with cylinder traps baited with either lure and multilure traps with BioLures were female biased. For the most part, both lures remained highly attractive and emitted detectable amounts of attractive components under hot field conditions for the duration of the 18-wk experiment. Total emission of ammonia was 4 times greater and 1-pyrroline at least 10 times greater from AFF lures compared with BioLures. Correlations of trap and lure performance with ammonia emission and weather were determined, but no conclusions were possible. Results indicate that BioLures would be the lure of choice in multilure or other McPhail-type traps and AFF lures would be superior with most sticky traps or kill stations that attract flies to outer (not enclosed) surfaces.

  5. Geographic Variation in Sexual Attraction of Spodoptera frugiperda Corn- and Rice-Strain Males to Pheromone Lures

    Science.gov (United States)

    Unbehend, Melanie; Hänniger, Sabine; Vásquez, Gissella M.; Juárez, María Laura; Reisig, Dominic; McNeil, Jeremy N.; Meagher, Robert L.; Jenkins, David A.; Heckel, David G.; Groot, Astrid T.

    2014-01-01

    The corn- and rice-strains of Spodoptera frugiperda exhibit several genetic and behavioral differences and appear to be undergoing ecological speciation in sympatry. Previous studies reported conflicting results when investigating male attraction to pheromone lures in different regions, but this could have been due to inter-strain and/or geographic differences. Therefore, we investigated whether corn- and rice-strain males differed in their response to different synthetic pheromone blends in different regions in North America, the Caribbean and South America. All trapped males were strain-typed by two strain-specific mitochondrial DNA markers. In the first experiment, we found a nearly similar response of corn- and rice-strain males to two different 4-component blends, resembling the corn- and rice-strain female blend we previously described from females in Florida. This response showed some geographic variation in fields in Canada, North Carolina, Florida, Puerto Rico, and South America (Peru, Argentina). In dose-response experiments with the critical secondary sex pheromone component (Z)-7-dodecenyl acetate (Z7-12:OAc), we found some strain-specific differences in male attraction. While the response to Z7-12:OAc varied geographically in the corn-strain, rice-strain males showed almost no variation. We also found that the minor compound (Z)-11-hexadecenyl acetate (Z11-16:OAc) did not increase attraction of both strains in Florida and of corn-strain males in Peru. In a fourth experiment, where we added the stereo-isomer of the critical sex pheromone component, (E)-7-dodecenyl acetate, to the major pheromone component (Z)-9-tetradecenyl acetate (Z9-14:OAc), we found that this compound was attractive to males in North Carolina, but not to males in Peru. Overall, our results suggest that both strains show rather geographic than strain-specific differences in their response to pheromone lures, and that regional sexual communication differences might cause geographic

  6. Brûlure chez l’épileptique: brûlure pas comme les autres

    Science.gov (United States)

    Boukind, S.; Elatiqi, O.K.; Dlimi, M.; Elamrani, D.; Benchamkha, Y.; Ettalbi, S.

    2015-01-01

    Summary L’association brûlure et épilepsie est une constatation fréquente au Maroc. Ces brûlures, souvent itératives, touchent le plus souvent des femmes jeunes de milieu rural. L’accident survient habituellement au domicile, le plus souvent dans la cuisine à la suite d’une chute sur un moyen de cuisson posé au sol. Elles peuvent être inaugurales de la maladie mais surviennent plus souvent chez des patients connus mais au traitement mal suivi. Les conséquences de ces brûlures, toujours profondes, sont souvent dramatiques en termes de séquelles, chez des patients ayant déjà une insertion sociale rendue difficile par l’épilepsie. La prise en charge doit être multidisciplinaire et concerner à la fois la brûlures et l’épilepsie. Des mesures de prévention simples, visant à équilibrer l’épilepsie et éviter au patient de se trouver seul à proximité d’une source de chaleur, doivent être mises en place. PMID:27252613

  7. Blended Learning

    NARCIS (Netherlands)

    Van der Baaren, John

    2009-01-01

    Van der Baaren, J. (2009). Blended Learning. Presentation given at the Mini symposium 'Blended Learning the way to go?'. November, 5, 2009, The Hague, The Netherlands: Netherlands Defence Academy (NDLA).

  8. Blended Learning

    OpenAIRE

    Bauerová, Andrea

    2013-01-01

    This thesis is focused on a new approach of education called blended learning. The history and developement of Blended Learning is described in the first part. Then the methods and tools of Blended Learning are evaluated and compared to the traditional methods of education. At the final part an efficient developement of the educational programs is emphasized.

  9. Cue lure and the mating behavior of male melon flies (Diptera: Tephritidae)

    International Nuclear Information System (INIS)

    Shelly, T.E.; Villalobos, E.M.

    1995-01-01

    Laboratory tests were conducted to assess the effect of the parapheromone cue lure on the mating behavior of male Bactrocera cucurbitae (Coquillett). Exposure to cue lure resulted in a short-term mating advantage. For wild flies, treated males that fed on cue lure on the day of testing, or 1 day prior to testing, mated more frequently than control males that had no prior exposure to cue lure. However, control and treated males had similar mating success in tests performed 3 or 7 days after the treated males were exposed to the lure. Exposure to cue lure also increased the mating success of mass-reared, irradiated males relative to unexposed wild males, though this advantage was evident for only 1 day following exposure. Cue lure appeared to enhance mating performance by increasing male wing-fanning activity but not the attractiveness of the signal per se. A field study revealed that irradiated males exposed to cue lure 1 week prior to release were less likely to be captured (in Steiner traps baited with cue lure and naled) than unexposed males. These findings suggest that exposure of sterile males to cue lure might improve the effectiveness of sterile insect release as well as enable simultaneous control programs of sterile insect release and male annihilation

  10. Avoidance and contextual learning induced by a kairomone, a pheromone and a common odorant in female CD1 mice

    Directory of Open Access Journals (Sweden)

    Lluís eFortes-Marco

    2015-10-01

    Full Text Available Chemosignals mediate both intra- and inter-specific communication in most mammals. Pheromones elicit stereotyped reactions in conspecifics, whereas kairomones provoke a reaction in an allospecific animal. For instance, predator kairomones elicit anticipated defensive responses in preys. The aim of this work was to test the behavioral responses of female mice to two chemosignals: 2-heptanone (2-HP, a putative alarm pheromone, and 2,4,5-trimethylthiazoline (TMT, a fox-derived putative kairomone, widely used to investigate fear and anxiety in rodents. The banana-like odorant isoamyl acetate (IA, unlikely to act as a chemosignal, served as a control odorant. We first presented increasing amounts of these odorants in consecutive days, in a test box in which mice could explore or avoid them. Female mice avoided the highest amounts of all three compounds, with TMT and IA eliciting avoidance at lower amounts (3.8 pmol and 0.35 μmol, respectively than 2-HP (35 μmol. All three compounds induced minimal effects in global locomotion and immobility in this set up. Further, mice detected 3.5 pmol of TMT and IA in a habituation-dishabituation test, so avoidance of IA started well beyond the detection threshold. Finally, both TMT and IA, but not 2-HP, induced conditioned place avoidance and increased immobility in the neutral compartment during a contextual memory test. These data suggest that intense odors can induce contextual learning irrespective of their putative biological significance. Our results support that synthetic predator-related compounds (like TMT or other intense odorants are useful to investigate the neurobiological basis of emotional behaviors in rodents. Since intense odorants unlikely to act as chemosignals can elicit similar behavioral reactions than chemosignals, we stress the importance of using behavioral measures in combination with other physiological (e.g. hormonal levels or neural measures (e.g. immediate early gene expression to

  11. Inhibition of predator attraction to kairomones by non-host plant volatiles for herbivores: a bypass-trophic signal.

    Directory of Open Access Journals (Sweden)

    Qing-He Zhang

    2010-06-01

    Full Text Available Insect predators and parasitoids exploit attractive chemical signals from lower trophic levels as kairomones to locate their herbivore prey and hosts. We hypothesized that specific chemical cues from prey non-hosts and non-habitats, which are not part of the trophic chain, are also recognized by predators and would inhibit attraction to the host/prey kairomone signals. To test our hypothesis, we studied the olfactory physiology and behavior of a predaceous beetle, Thanasimus formicarius (L. (Coleoptera: Cleridae, in relation to specific angiosperm plant volatiles, which are non-host volatiles (NHV for its conifer-feeding bark beetle prey.Olfactory detection in the clerid was confirmed by gas chromatography coupled to electroantennographic detection (GC-EAD for a subset of NHV components. Among NHV, we identified two strongly antennally active molecules, 3-octanol and 1-octen-3-ol. We tested the potential inhibition of the combination of these two NHV on the walking and flight responses of the clerid to known kairomonal attractants such as synthetic mixtures of bark beetle (Ips spp. aggregation pheromone components (cis-verbenol, ipsdienol, and E-myrcenol combined with conifer (Picea and Pinus spp. monoterpenes (alpha-pinene, terpinolene, and Delta(3-carene. There was a strong inhibitory effect, both in the laboratory (effect size d = -3.2, walking bioassay and in the field (d = -1.0, flight trapping. This is the first report of combining antennal detection (GC-EAD and behavioral responses to identify semiochemical molecules that bypass the trophic system, signaling habitat information rather than food related information.Our results, along with recent reports on hymenopteran parasitoids and coleopteran predators, suggest that some NHV chemicals for herbivores are part of specific behavioral signals for the higher trophic level and not part of a background noise. Such bypass-trophic signals could be of general importance for third trophic level

  12. Avoidance and contextual learning induced by a kairomone, a pheromone and a common odorant in female CD1 mice.

    Science.gov (United States)

    Fortes-Marco, Lluís; Lanuza, Enrique; Martínez-García, Fernando; Agustín-Pavón, Carmen

    2015-01-01

    Chemosignals mediate both intra- and inter-specific communication in most mammals. Pheromones elicit stereotyped reactions in conspecifics, whereas kairomones provoke a reaction in an allospecific animal. For instance, predator kairomones elicit anticipated defensive responses in preys. The aim of this work was to test the behavioral responses of female mice to two chemosignals: 2-heptanone (2-HP), a putative alarm pheromone, and 2,4,5-trimethylthiazoline (TMT), a fox-derived putative kairomone, widely used to investigate fear and anxiety in rodents. The banana-like odorant isoamyl acetate (IA), unlikely to act as a chemosignal, served as a control odorant. We first presented increasing amounts of these odorants in consecutive days, in a test box in which mice could explore or avoid them. Female mice avoided the highest amounts of all three compounds, with TMT and IA eliciting avoidance at lower amounts (3.8 pmol and 0.35 μmol, respectively) than 2-HP (35 μmol). All three compounds induced minimal effects in global locomotion and immobility in this set up. Further, mice detected 3.5 pmol of TMT and IA in a habituation-dishabituation test, so avoidance of IA started well beyond the detection threshold. Finally, both TMT and IA, but not 2-HP, induced conditioned place avoidance and increased immobility in the neutral compartment during a contextual memory test. These data suggest that intense odors can induce contextual learning irrespective of their putative biological significance. Our results support that synthetic predator-related compounds (like TMT) or other intense odorants are useful to investigate the neurobiological basis of emotional behaviors in rodents. Since intense odorants unlikely to act as chemosignals can elicit similar behavioral reactions than chemosignals, we stress the importance of using behavioral measures in combination with other physiological (e.g., hormonal levels) or neural measures (e.g., immediate early gene expression) to establish

  13. Polymer blends

    Energy Technology Data Exchange (ETDEWEB)

    Allen, Scott D.; Naik, Sanjeev

    2017-08-22

    The present invention provides, among other things, extruded blends of aliphatic polycarbonates and polyolefins. In one aspect, provided blends comprise aliphatic polycarbonates such as poly(propylene carbonate) and a lesser amount of a crystalline or semicrystalline polymer. In certain embodiments, provided blends are characterized in that they exhibit unexpected improvements in their elongation properties. In another aspect, the invention provides methods of making such materials and applications of the materials in applications such as the manufacture of consumer packaging materials.

  14. Vitamin A deficiency modifies response of predatory mite Amblyseius potentillae to volatile kairomone of two-spotted spider mite, Tetranychus urticae.

    NARCIS (Netherlands)

    Dicke, M.; Sabelis, M.W.; Groeneveld, A.

    1986-01-01

    volatile kairomone of the two-spotted spider mite,Tetranychus urticae, elicits a searching response of the phytoseiid predatorAmblyseius potentillae, only when the predator is reared on a carotenoid-free diet. However, after addition of crystalline betta-carotene or vitamin A acetate to the

  15. Blended learning

    DEFF Research Database (Denmark)

    Staugaard, Hans Jørgen

    2012-01-01

    Forsøg på at indkredse begrebet blended learning i forbindelse med forberedelsen af projekt FlexVid.......Forsøg på at indkredse begrebet blended learning i forbindelse med forberedelsen af projekt FlexVid....

  16. Blended Learning

    Science.gov (United States)

    Imbriale, Ryan

    2013-01-01

    Teachers always have been and always will be the essential element in the classroom. They can create magic inside four walls, but they have never been able to create learning environments outside the classroom like they can today, thanks to blended learning. Blended learning allows students and teachers to break free of the isolation of the…

  17. Blended learning

    DEFF Research Database (Denmark)

    Dau, Susanne

    2016-01-01

    Blended Learning has been implemented, evaluated and researched for the last decades within different educational areas and levels. Blended learning has been coupled with different epistemological understandings and learning theories, but the fundamental character and dimensions of learning...... in blended learning are still insufficient. Moreover, blended learning is a misleading concept described as learning, despite the fact that it fundamentally is an instructional and didactic approach (Oliver & Trigwell, 2005) addressing the learning environment (Inglis, Palipoana, Trenhom & Ward, 2011......) instead of the learning processes behind. Much of the existing research within the field seems to miss this perspective. The consequence is a lack of acknowledgement of the driven forces behind the context and the instructional design limiting the knowledge foundation of learning in blended learning. Thus...

  18. Ustioni da fuoco / Burn injuries / Les brûlures

    Directory of Open Access Journals (Sweden)

    Liliana Copertino

    2008-04-01

    Full Text Available Severe burn injuries require high specialistic treatment. Burn injuries are common in disasters and war scenarios, so war medicine has been fundamental to improve treatment protocols for burn patients..Burn injuries are classified according to the etiopathogenetic agent (physical, chemical or radiation, that determines different anatomoisthologic aspects.An estimation of the depth and extension are fundamental for defining the gravity of the burn. Critical burn patients have to be transported in specialistic Centers. There they are treated by multispecialistic teams from the resuscitation phase to the reconstructive surgery and specialist rehabilitation.. This process can continue for two years with the objective to return patients to a quiet normal life. Les brûlures sont des lésions traumatiques qui requièrent un traitement spécialisé. Lors de catastrophes et de guerres, les brûlures sont des lésions très fréquentes et la médecine de guerre a contribué à faire avancer la science de manière importante, dans le traitement de cette pathologie.Les brûlures sont classées en fonction de l'agent étiopathogénique (agents physiques, chimiques ou radiations dont le mécanisme d'action qui provoque la lésion cause des aspects anatomohistologiques caractéristiques.Pour définir la sévérité d'une brûlure, il est aussi fondamental d'éstimer l'extension de la surface corporelle et la profondeur de l'épiderme, et éventuellement du derme, atteints. Les patients gravement brûlés doivent être hospitalisés dans des Centres Spécialisés où des équipes multispécialistes les suivent de la phase initiale de la réanimation aux phases de chirurgie reconstructive et au processus de réhabilitation. Ces dernières phases peuvent se prolonger pendant les deux années suivant le traumatisme avant qu'une réintégration dans une vie sociale acceptable ne puisse être faite.

  19. Effect of lures and colors on capture of lady beetles (coleoptera: coccinellidae) in tedders pyramidal traps

    Science.gov (United States)

    Purposeful attraction and/or aggregation of adult Coccinellidae at target sites would be useful for sampling purposes and/or pest suppression. We field-tested 1) lures in yellow and black pyramidal traps and 2) pyramidal traps that had been painted one or two colors (without lures) to determine if ...

  20. The potential use of lures for thrips biocontrol in greenhouses: practice and theory

    NARCIS (Netherlands)

    Teulon, D.A.J.; Davidson, M.M.; Nielsen, M.C.; Perry, N.B.; Tol, van R.W.H.M.; Kogel, de W.J.

    2008-01-01

    Exploiting the response of thrips pest species to odours has long been a goal for improving thrips pest management including biological control. Applications of attractants could include improved monitoring, push-pull (in conjunction with a repellent odour), lure and kill, and lure and infect

  1. The potential use of lures for thrips biological control in greenhouses: practice and theory

    NARCIS (Netherlands)

    Teulon, D.A.J.; Davidson, M.M.; Nielsen, M.C.; Perry, N.B.; Tol, van R.W.H.M.; Kogel, de W.J.

    2008-01-01

    Exploiting the response of thrips pest species to odours has long been a goal for improving thrips pest management including biological control. Applications of attractants could include improved monitoring, push-pull (in conjunction with a repellent odour), lure and kill, and lure and infect

  2. Variation in the standard deviation of the lure rating distribution: Implications for estimates of recollection probability.

    Science.gov (United States)

    Dopkins, Stephen; Varner, Kaitlin; Hoyer, Darin

    2017-10-01

    In word recognition semantic priming of test words increased the false-alarm rate and the mean of confidence ratings to lures. Such priming also increased the standard deviation of confidence ratings to lures and the slope of the z-ROC function, suggesting that the priming increased the standard deviation of the lure evidence distribution. The Unequal Variance Signal Detection (UVSD) model interpreted the priming as increasing the standard deviation of the lure evidence distribution. Without additional parameters the Dual Process Signal Detection (DPSD) model could only accommodate the results by fitting the data for related and unrelated primes separately, interpreting the priming, implausibly, as decreasing the probability of target recollection (DPSD). With an additional parameter, for the probability of false (lure) recollection the model could fit the data for related and unrelated primes together, interpreting the priming as increasing the probability of false recollection. These results suggest that DPSD estimates of target recollection probability will decrease with increases in the lure confidence/evidence standard deviation unless a parameter is included for false recollection. Unfortunately the size of a given lure confidence/evidence standard deviation relative to other possible lure confidence/evidence standard deviations is often unspecified by context. Hence the model often has no way of estimating false recollection probability and thereby correcting its estimates of target recollection probability.

  3. Teaching Young Adults with Disabilities to Respond Appropriately to Lures from Strangers

    Science.gov (United States)

    Fisher, Marisa H.; Burke, Meghan M.; Griffin, Megan M.

    2013-01-01

    We taught 5 adults with mild intellectual disabilities to respond appropriately to lures from strangers. Skills were taught in the classroom first and then in situ. Before training, participants did not walk away from confederate strangers who tried to lure them away. Participants demonstrated appropriate responses during classroom and in situ…

  4. Range of Attraction of Pheromone Lures and Dispersal Behavior of Cerambycid Beetles

    Science.gov (United States)

    E. Dunn; J. Hough-Goldstein; L. M. Hanks; J. G. Millar; V. D' Amico

    2016-01-01

    Cerambycid beetles (Coleoptera: Cerambycidae) can locate suitable hosts and mates by sensing pheromones and plant volatiles. Many cerambycid pheromone components have been identified and are now produced synthetically for trap lures. The range over which these lures attract cerambycids within a forest, and the tendency for cerambycids to move out of a forest in...

  5. Demonstration and Characterization of a Persistent Pheromone Lure for the Navel Orangeworm, Amyelois transitella (Lepidoptera: Pyralidae

    Directory of Open Access Journals (Sweden)

    Bradley S. Higbee

    2014-07-01

    Full Text Available The lack of an effective pheromone lure has made it difficult to monitor and manage the navel orangeworm, Amyelois transitella (Lepidoptera: Pyralidae, in the economically important crops in which it is the primary insect pest. A series of experiments was conducted to demonstrate and characterize a practical synthetic pheromone lure for capturing navel orangeworm males. Traps baited with lures prepared with 1 or 2 mg of a three- or four-component formulation captured similar numbers of males. The fluctuation over time in the number of males captured in traps baited with the pheromone lure correlated significantly with males captured in female-baited traps. Traps baited with the pheromone lure usually did not capture as many males as traps baited with unmated females, and the ratio of males trapped with pheromone to males trapped with females varied between crops and with abundance. The pheromone lure described improves the ability of pest managers to detect and monitor navel orangeworm efficiently and may improve management and decrease insecticide treatments applied as a precaution against damage. Awareness of differences between male interaction with the pheromone lure and calling females, as shown in these data, will be important as further studies and experience determine how best to use this lure for pest management.

  6. Geographic variation in sexual attraction of Spodoptera frugiperda corn- and rice-strain males to pheromone lures.

    Directory of Open Access Journals (Sweden)

    Melanie Unbehend

    Full Text Available The corn- and rice-strains of Spodoptera frugiperda exhibit several genetic and behavioral differences and appear to be undergoing ecological speciation in sympatry. Previous studies reported conflicting results when investigating male attraction to pheromone lures in different regions, but this could have been due to inter-strain and/or geographic differences. Therefore, we investigated whether corn- and rice-strain males differed in their response to different synthetic pheromone blends in different regions in North America, the Caribbean and South America. All trapped males were strain-typed by two strain-specific mitochondrial DNA markers. In the first experiment, we found a nearly similar response of corn- and rice-strain males to two different 4-component blends, resembling the corn- and rice-strain female blend we previously described from females in Florida. This response showed some geographic variation in fields in Canada, North Carolina, Florida, Puerto Rico, and South America (Peru, Argentina. In dose-response experiments with the critical secondary sex pheromone component (Z-7-dodecenyl acetate (Z7-12:OAc, we found some strain-specific differences in male attraction. While the response to Z7-12:OAc varied geographically in the corn-strain, rice-strain males showed almost no variation. We also found that the minor compound (Z-11-hexadecenyl acetate (Z11-16:OAc did not increase attraction of both strains in Florida and of corn-strain males in Peru. In a fourth experiment, where we added the stereo-isomer of the critical sex pheromone component, (E-7-dodecenyl acetate, to the major pheromone component (Z-9-tetradecenyl acetate (Z9-14:OAc, we found that this compound was attractive to males in North Carolina, but not to males in Peru. Overall, our results suggest that both strains show rather geographic than strain-specific differences in their response to pheromone lures, and that regional sexual communication differences might cause

  7. Interactions among Carbon Dioxide, Heat, and Chemical Lures in Attracting the Bed Bug, Cimex lectularius L. (Hemiptera: Cimicidae

    Directory of Open Access Journals (Sweden)

    Narinderpal Singh

    2012-01-01

    Full Text Available Commercial bed bug (Cimex lectularius L. monitors incorporating carbon dioxide (CO2, heat, and chemical lures are being used for detecting bed bugs; however, there are few reported studies on the effectiveness of chemical lures in bed bug monitors and the interactions among chemical lure, CO2, and heat. We screened 12 chemicals for their attraction to bed bugs and evaluated interactions among chemical lures, CO2, and heat. The chemical lure mixture consisting of nonanal, 1-octen-3-ol, spearmint oil, and coriander Egyptian oil was found to be most attractive to bed bugs and significantly increased the trap catches in laboratory bioassays. Adding this chemical lure mixture when CO2 was present increased the trap catches compared with traps baited with CO2 alone, whereas adding heat did not significantly increase trap catches when CO2 was present. Results suggest a combination of chemical lure and CO2 is essential for designing effective bed bug monitors.

  8. Word type effects in false recall: concrete, abstract, and emotion word critical lures.

    Science.gov (United States)

    Bauer, Lisa M; Olheiser, Erik L; Altarriba, Jeanette; Landi, Nicole

    2009-01-01

    Previous research has demonstrated that definable qualities of verbal stimuli have implications for memory. For example, the distinction between concrete and abstract words has led to the finding that concrete words have an advantage in memory tasks (i.e., the concreteness effect). However, other word types, such as words that label specific human emotions, may also affect memory processes. This study examined the effects of word type on the production of false memories by using a list-learning false memory paradigm. Participants heard lists of words that were highly associated to nonpresented concrete, abstract, or emotion words (i.e., the critical lures) and then engaged in list recall. Emotion word critical lures were falsely recalled at a significantly higher rate (with the effect carried by the positively valenced critical lures) than concrete and abstract critical lures. These findings suggest that the word type variable has implications for our understanding of the mechanisms that underlie recall and false recall.

  9. The Lure of Casino Gambling and Its Potential Impact on College Students in Mississippi.

    Science.gov (United States)

    Bailey, E. Ann; Burroughs, Susie W.; Dabit, Jean S.; Hambrick, Rosalind S.; Theriot, Patricia B.

    1997-01-01

    Investigates the lure and potential impact of casino gambling on college students in Mississippi. Findings suggest that casino gambling may significantly impact college students in regard to financial management, alcohol consumption, academic progress, and behavioral changes. (MKA)

  10. Assassin bug uses aggressive mimicry to lure spider prey.

    Science.gov (United States)

    Wignall, Anne E; Taylor, Phillip W

    2011-05-07

    Assassin bugs (Stenolemus bituberus) hunt web-building spiders by invading the web and plucking the silk to generate vibrations that lure the resident spider into striking range. To test whether vibrations generated by bugs aggressively mimic the vibrations generated by insect prey, we compared the responses of spiders to bugs with how they responded to prey, courting male spiders and leaves falling into the web. We also analysed the associated vibrations. Similar spider orientation and approach behaviours were observed in response to vibrations from bugs and prey, whereas different behaviours were observed in response to vibrations from male spiders and leaves. Peak frequency and duration of vibrations generated by bugs were similar to those generated by prey and courting males. Further, vibrations from bugs had a temporal structure and amplitude that were similar to vibrations generated by leg and body movements of prey and distinctly different to vibrations from courting males or leaves, or prey beating their wings. To be an effective predator, bugs do not need to mimic the full range of prey vibrations. Instead bugs are general mimics of a subset of prey vibrations that fall within the range of vibrations classified by spiders as 'prey'.

  11. [Luring effect of the fermented Laminaria japonica to Oncomelania hupensis].

    Science.gov (United States)

    Ma, An-ning; Ni, Hong; Wang, Wan-xian; Zhang, Yun; Geng, Peng

    2010-02-01

    To study the attraction effect of the food attractants on Oncomelania hupensis. Oncomelania snail food was prepared with the fermented kelp (Laminaria japonica) mixed with corn starch. Snails were fed with the food and kept for 12, 24, 36, and 48 h at 15, 25, 35 degrees C respectively. Meanwhile, snail-killing effect was tested by granules containing jack-in-the-pulpit (Arisama heterophyllum) with or without the fermented kelp under the condition of 25 degrees C, 30% or 60% soil humidity. The snail-attracting rate of the fermented kelp was affected by the temperature, highest under 25 degrees C and lowest under 35 degrees C at any time point, with a rate of 80.3% in 48 h at 25 degrees C which was higher than that of the control (17.0%) (Pjack-in-the-pulpit with fermented kelp (85.3%) was higher than that of the group without fermented kelp (26.8%) (P<0.05). The mortality under 60% of soil humidity was higher than that under 30% humidity (P<0.01). The fermented kelp shows a strong luring effect to the Oncomelania snails.

  12. Jewelled spiders manipulate colour-lure geometry to deceive prey.

    Science.gov (United States)

    White, Thomas E

    2017-03-01

    Selection is expected to favour the evolution of efficacy in visual communication. This extends to deceptive systems, and predicts functional links between the structure of visual signals and their behavioural presentation. Work to date has primarily focused on colour, however, thereby understating the multicomponent nature of visual signals. Here I examined the relationship between signal structure, presentation behaviour, and efficacy in the context of colour-based prey luring. I used the polymorphic orb-web spider Gasteracantha fornicata , whose yellow- or white-and-black striped dorsal colours have been broadly implicated in prey attraction. In a manipulative assay, I found that spiders actively control the orientation of their conspicuous banded signals in the web, with a distinct preference for near-diagonal bearings. Further field-based study identified a predictive relationship between pattern orientation and prey interception rates, with a local maximum at the spiders' preferred orientation. There were no morph-specific effects on capture success, either singularly or via an interaction with pattern orientation. These results reveal a dynamic element in a traditionally 'static' signalling context, and imply differential functions for chromatic and geometric signal components across visual contexts. More broadly, they underscore how multicomponent signal designs and display behaviours may coevolve to enhance efficacy in visual deception. © 2017 The Author(s).

  13. Field and laboratory responses of adult Ixodes scapularis (Acari: Ixodidae) to kairomones produced by white-tailed deer.

    Science.gov (United States)

    Carroll, J F; Mills, G D; Schmidtmann, E T

    1996-07-01

    In a field test, adult blacklegged ticks, Ixodes scapularis Say, of both sexes exhibited an arrestant response to substances associated with external glands on the legs of white-tailed deer, Odocoileus virginianus (Zimmermann), their principal host. Substances rubbed from the pelage covering tarsal and interdigital glands were applied to artificial vantage points simulating vegetation on which I. scapularis adults wait for host contact. A combination of tarsal substances (applied to the apex of the simulated vantage point) and interdigital gland substances (applied to the horizontal base) elicited a greater response than either treatment alone. A minimal response was observed on untreated vantage points. In laboratory bioassays using glass tubing as vantage points, substances associated with preorbital glands of deer elicited a strong arrestant response among I. scapularis females, whereas samples rubbed from the forehead, back, and a nonglandular area on deer tarsi evoked weak arrestant responses. These results support the hypothesis that the kairomonal properties of host-generated residues, either in conjunction with or in lieu of the effects of carbon dioxide, help account for the prevalence of host-seeking ticks along animal trails.

  14. Novel approaches to pin cluster synchronization on complex dynamical networks in Lur'e forms

    Science.gov (United States)

    Tang, Ze; Park, Ju H.; Feng, Jianwen

    2018-04-01

    This paper investigates the cluster synchronization of complex dynamical networks consisted of identical or nonidentical Lur'e systems. Due to the special topology structure of the complex networks and the existence of stochastic perturbations, a kind of randomly occurring pinning controller is designed which not only synchronizes all Lur'e systems in the same cluster but also decreases the negative influence among different clusters. Firstly, based on an extended integral inequality, the convex combination theorem and S-procedure, the conditions for cluster synchronization of identical Lur'e networks are derived in a convex domain. Secondly, randomly occurring adaptive pinning controllers with two independent Bernoulli stochastic variables are designed and then sufficient conditions are obtained for the cluster synchronization on complex networks consisted of nonidentical Lur'e systems. In addition, suitable control gains for successful cluster synchronization of nonidentical Lur'e networks are acquired by designing some adaptive updating laws. Finally, we present two numerical examples to demonstrate the validity of the control scheme and the theoretical analysis.

  15. Waste zone labelling at the Lure accelerator facility

    International Nuclear Information System (INIS)

    Cometto, M.; Damoy, F.; Giacri-Mauborgne, M.L.; Ridikas, D.; Thomas, W.

    2005-01-01

    This document describes the method used to compute the activation of the structure components near the electron-positron converter of the Lure accelerator (Orsay). Activation comes from photon and neutron reactions on nuclei belonging to the concrete structure. Only radio-nuclides with a half-life greater than 200 days are considered penalizing for dismantling operations. The main photonuclear reactions produce the following nuclides: Na 22 , Cl 36 , Mn 54 , Nb 92 , Ba 133 , Co 57 and Co 60 . The main neutron reaction generate the following nuclides: H 3 , C 14 , Cl 36 , K 40 , Co 60 , Ni 63 , Zn 65 , Se 79 , Zr 93 , Ag 108 , Ag 110 , Ba 133 , Cs 134 , Eu 152 , Eu 154 , Fe 55 , Ca 41 , Na 22 , Mn 54 , Cs 137 , Nb 92 and Ti 204 . The MCNPX code has been used to compute the values of the photon and neutron fluxes received by the structure components, the activation has been computed with the Cinder code from the flux values. The main contributors for radioactivity on long term basis appear to be Ca 41 and Ni 63 . Calculations have been compared with the measurement of activities of 3 concrete samples drilled out from the structure. The results of the comparison are given for Co 60 , Cs 134 , Eu 152 and Eu 154 . The computed values appear to be greater by a factor varying from 2 to 5 which is consistent with the method used that naturally overestimates the activation. These results are considered as satisfactory for performing waste zone labelling. (A.C.)

  16. A promising biotechnical approach to pest management of Diabrotica virgifera virgifera in Illinois maize fields under kairomonal shielding with the new MSD technique.

    Science.gov (United States)

    Hummel, H E; Shaw, J T; Hein, D F

    2005-01-01

    Environmentally compatible and sustainable plant protection requires novel approaches to pest management characterized by minimal emphasis on toxicants. Classical toxicants traditionally dominated economic entomology for half a century. But worldwide problems with environmental pollution and with increasing resistance levels in all major pesticide classes and in many key insect species including Diabrotica virgifera virgifera (D.v.v.) strongly advocate a rethinking and a change in management paradigms used. Soft, minimally invasive, biological, biotechnical and cultural approaches should replace hard pesticides which are in favor up to now. Fortunately, pheromones, kairomones, plant attractants, better traps, new plant varieties and cultural methods like crop rotation, in short more sophisticated methods are now available as pressure for finding and exploring novel strategies increases. Facing this situation, a new biotechnical approach of population reduction of D.v.v., called "MSD" technique, is introduced. MSD is characterized as an approach combining mass trapping, shielding and deflecting of adult insects along an invisible odor barrier of synthetic kairomone which diminishes the flux of insects across a high capacity trap line baited with kairomone, thus reducing both the population fluctuation and number and its reproductive success within the shielded area. In the case of D.v.v. in Zea mays fields, effects realized by the MSD technique have been measured simultaneously by a number of independent criteria during the summers of 2003 and 2004 at 2 different locations in Illinois maize fields of up to one half hectare size. Results observed are statistically significant and cannot be explained by mass trapping alone. There is also an additional shielding and deflection, in short "diversion" effect whose basic sensory and behavioral mechanisms call for future exploration.

  17. Activating the critical lure during study is unnecessary for false recognition.

    Science.gov (United States)

    Zeelenberg, René; Boot, Inge; Pecher, Diane

    2005-06-01

    Participants studied lists of nonwords (e.g., froost, floost, stoost, etc.) that were orthographic-phonologically similar to a nonpresented critical lure, which was also a nonword (e.g., ploost). Experiment 1 showed a high level of false recognition for the critical lure. Experiment 2 showed that the false recognition effect was also present for forewarned participants who were informed about the nature of the false recognition effect and told to avoid making false recognition judgments. The present results show that false recognition effects can be obtained even when the critical lure itself is not stored during study. This finding is problematic for accounts that attribute false memories to implicit associative responses or spreading activation but is easily explained by global familiarity models of recognition memory.

  18. Evaluation of methyl salicylate lures on populations of Typhlodromus pyri (Acari: Phytoseiidae) and other natural enemies in vineyards

    Science.gov (United States)

    Methyl salicylate (MeSA), an herbivore induced plant volatile, can potentially elicit control of pests through attraction of beneficial arthropods. This study evaluates the effect of synthetic MeSA lures (PredaLure) on arthropod populations during the 2009 and 2010 seasons in two Oregon vineyards (...

  19. Benzalkonium Chloride Provides Remarkable Stability to Liquid Protein Lures for Trapping Anastrepha obliqua (Diptera: Tephritidae).

    Science.gov (United States)

    Lasa, R; Williams, T

    2017-12-05

    Hydrolyzed protein lures are widely used to monitor fruit fly pests but are rapidly degraded by microbial activity and must be replaced frequently. To improve the stability of lures, the quaternary ammonium biocide, benzalkonium chloride (BC), was evaluated in mixtures with two hydrolyzed proteins commonly used to monitor Anastrepha spp. The mean number of Anastrepha obliqua adults captured during six consecutive weeks using Captor + borax with the addition of 240 mg BC/liter, not renewed during the test, was similar to Captor + borax that was replaced at weekly intervals and was more effective than Captor + borax without BC. Numbers of A. obliqua flies captured in 30% CeraTrap diluted in water containing 240 mg BC/liter were similar to those caught in traps baited with Captor + borax or 30% CeraTrap without BC in the first 9 d of evaluation but was significantly more effective than both lures after 56 d. After >2 mo of use, 30% CeraTrap containing 240 mg BC/liter remained as effective as newly prepared 30% CeraTrap. The addition of BC to lures reduced surface tension of liquid lures by ~40-50%. However, when BC was increased to 720 mg BC/liter, only a small additional reduction in surface tension was observed and higher concentrations of BC did not increase capture rates. These findings could contribute to reduced costs for trapping networks and the development of long-lasting formulations of liquid protein lures for bait stations and mass-trapping targeted at major tephritid pests. © The Author(s) 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  20. Scent Lure Effect on Camera-Trap Based Leopard Density Estimates.

    Directory of Open Access Journals (Sweden)

    Alexander Richard Braczkowski

    Full Text Available Density estimates for large carnivores derived from camera surveys often have wide confidence intervals due to low detection rates. Such estimates are of limited value to authorities, which require precise population estimates to inform conservation strategies. Using lures can potentially increase detection, improving the precision of estimates. However, by altering the spatio-temporal patterning of individuals across the camera array, lures may violate closure, a fundamental assumption of capture-recapture. Here, we test the effect of scent lures on the precision and veracity of density estimates derived from camera-trap surveys of a protected African leopard population. We undertook two surveys (a 'control' and 'treatment' survey on Phinda Game Reserve, South Africa. Survey design remained consistent except a scent lure was applied at camera-trap stations during the treatment survey. Lures did not affect the maximum movement distances (p = 0.96 or temporal activity of female (p = 0.12 or male leopards (p = 0.79, and the assumption of geographic closure was met for both surveys (p >0.05. The numbers of photographic captures were also similar for control and treatment surveys (p = 0.90. Accordingly, density estimates were comparable between surveys (although estimates derived using non-spatial methods (7.28-9.28 leopards/100km2 were considerably higher than estimates from spatially-explicit methods (3.40-3.65 leopards/100km2. The precision of estimates from the control and treatment surveys, were also comparable and this applied to both non-spatial and spatial methods of estimation. Our findings suggest that at least in the context of leopard research in productive habitats, the use of lures is not warranted.

  1. Effect of methyl salicylate-based lures on beneficial and pest arthropods in strawberry.

    Science.gov (United States)

    Lee, Jana C

    2010-04-01

    Methyl salicylate (MeSA) is a common herbivore-induced plant volatile that, when applied to crops, has the potential to enhance natural enemy abundance and pest control. The impacts of MeSA in strawberry were unknown and examined in the spring and midsummer period. Strawberry plots contained no lures (control) or two 30-d MeSA lures (Predalure) in the center: one lure 0.61 m aboveground over a sticky trap, and one lure on a plant near the ground. Arthropod abundance was monitored at the point source, 5 m and 10 m away from lures over 31 d with white sticky traps, pitfall traps, and leaf inspection. Twenty-seven and nine comparisons were made among beneficial and pest arthropods, respectively. Overall positive responses were found among Chrysopidae in July-August 2008 and Orius tristicolor (White) in May-June 2009 to MeSA based on sticky traps. Chrysopidae showed attraction to the point source, but not at 5 m and 10 m. Ground-dwelling predators collected in pitfall traps such as Araneae, the carabid beetles, Pterostichus melanarius (Illiger), and Nebria brevicollis (Fabricius) did not respond. Increased abundance of six natural enemy groups appeared on various dates between 3 and 24 d after placement of lures in the field based on leaf inspection and sticky traps. Conversely, fewer Coccinellidae were captured on sticky traps on days 0-3, and fewer natural enemies were observed on leaves on day 28 in MeSA plots. MeSA did not increase nor decrease pest abundance.

  2. Nantucket pine tip moth, Rhyacionia Frustrana, lures and traps: What is the optimum combination?

    Science.gov (United States)

    Gary L. DeBarr; J. wayne Brewer; R. Scott Cameron; C. Wayne Berisford

    1999-01-01

    Pheromone traps are used to monitor flight activity of male Nantucket pine tip moths, Rhyacionia frustrana (Comstock), to initialize spray timing models, determine activity periods, or detect population trends. However, a standardized trapping procedure has not been developed. The relative efficacies of six types of lures and eight commercial pheromone traps were...

  3. Effect of storage of pheromone lures for Amyelois transitella: field performance and compound ratios

    Science.gov (United States)

    Experiments during the flight of the overwintering generation of navel orangeworm revealed that Suterra NOW Biolure pheromone lures held in storage at -20°C increased significantly in field effectiveness with time in storage over a period of 0-2 years. This increase in field effectiveness coincided ...

  4. Manipulation of insect behavior with Specialized Pheromone & Lure Application Technology (SPLAT®)

    Science.gov (United States)

    Agenor Mafra-Neto; Frédérique M. de Lame; Christopher J. Fettig; A. Steven Munson; Thomas M. Perring; Lukasz L. Stelinski; Lyndsie Stoltman; Leandro E.J. Mafra; Rafael Borges; Roger I. Vargas

    2013-01-01

    SPLAT® (Specialized Pheromone and Lure Application Technology) emulsion is a unique controlled-release technology that can be adapted to dispense and protect a wide variety of compounds from degradation, including semiochemicals, pesticides, and phagostimulants, in diverse environments. ISCA Technologies, Inc., in collaboration with colleagues in academia, government,...

  5. An improved condition for master-slave synchronization of Lur'e systems with time delay

    International Nuclear Information System (INIS)

    Xiang, Ji; Li, Yanjun; Wei, Wei

    2007-01-01

    In this Letter, a new sufficient condition is proposed for master-slave synchronization of Lur'e system with time delay. This condition is constructed on the new integral inequality method such that the obtained result is much sharper than that in [M.E.Y. Yalcin, J.A.K. Suykens, J. Vandewalle, Int. J. Bifur. Chaos 11 (2001) 1707

  6. Identification of candidate volatiles that affect the behavioural response of the malaria mosquito Anopheles gambiae sensu stricto to an active kairomone blend: laboratory and semi-field assays

    NARCIS (Netherlands)

    Smallegange, R.C.; Bukovinszkine Kiss, G.; Otieno, B.; Mbadi, P.A.; Takken, W.; Mukabana, W.R.; Loon, van J.J.A.

    2012-01-01

    Anopheles gambiae Giles sensu stricto (Diptera: Culicidae) is the most important vector of human malaria in sub-Saharan Africa, affecting the lives of millions of people. Existing tools such as insecticide-treated nets and indoor-residual sprays are not only effective, but also have limitations as a

  7. Carnivore Attractant or Plant Elicitor? Multifunctional Roles of Methyl Salicylate Lures in Tomato Defense.

    Science.gov (United States)

    Rowen, Elizabeth; Gutensohn, Michael; Dudareva, Natalia; Kaplan, Ian

    2017-06-01

    Synthetic plant volatile lures attract natural enemies, but may have non-target effects due to the multifunctional nature of volatile signals. For example, methyl salicylate (MeSA) is used to attract predators, yet also serves as a signaling hormone involved in plant pathogen defense. We investigated the consequences of deploying MeSA lures to attract predators for tomato (Solanum lycopersicum) defense against herbivores. To understand the spatial distribution of the lure's effect, we exposed tomatoes in the field to MeSA along a linear distance gradient and induced defenses by simulating feeding by hornworm caterpillars in a fully crossed factorial design (+/- MeSA, +/- herbivory). Subsequently, we analyzed activity of several defensive proteins (protease inhibitors, polyphenol oxidase, peroxidase), development of hornworm larvae (Manduca sexta), growth of fungal pathogens (Cladosporium and Alternaria), and attractiveness to herbivores and predators. Overall, MeSA-exposed plants were more resistant to both insects and pathogens. Secondary pathogen infection was reduced by 25% in MeSA exposed plants, possibly due to elevated polyphenol oxidase activity. Interestingly, we found that lures affected plant pathogen defenses equivalently across all distances (up to 4 m away) indicating that horizontal diffusion of a synthetic volatile may be greater than previously assumed. While thrips avoided colonizing hornworm- damaged tomato plants, this induced resistance was not observed upon pre-exposure to MeSA, suggesting that MeSA suppresses the repellant effect induced by herbivory. Thus, using MeSA lures in biological control may inadvertently protect crops from pathogens, but has mixed effects on plant resistance to insect herbivores.

  8. Synthetic blends of volatile, phytopathogen-induced odorants can be used to manipulate vector behavior.

    Directory of Open Access Journals (Sweden)

    Alexander eAksenov

    2014-12-01

    Full Text Available Volatile organic compounds (VOCs are emitted from all plants and these VOCs are important means of communication between plants and insects. It has been documented that pathogen infections alter VOC profiles rendering infected plants more attractive to specific vectors transmitting these pathogens than uninfected plants, thus potentially aiding in pathogen propagation. Mimicking these chemical cues might enable insect attraction away from the plant or disruption of host finding behavior of the vector. However, the practical implications have not been fully explored. We used citrus, Diaphorina citri and huanglongbing (HLB as a model host-vector-disease system because HLB threatens citrus production worldwide and is similar to other critical diseases of food crops, such as Zebra Chip affecting potato. We formulated a synthetic chemical blend using selected HLB-specific biomarker compounds, and tested the blend with the Attenu assay system for chemosensory proteins. The Attenu assay system is a procedure that identifies interactions between insect chemosensory proteins and their ligands. We found that an equimolar mixture of compounds mimicking the volatile profile of HLB-infected citrus bound chemosensory proteins. Further investigation of this blend in laboratory behavioral assays resulted in development of a synthetic lure that was more attractive to D. citri than natural citrus tree volatiles. This strategy could provide a new route to produce chemical lures for vector population control for a variety of plant and/or animal systems and it may result in the development of a practical lure for monitoring vectors of disease, such as D. citri.

  9. Respuesta kairomonal de coleópteros asociados a Dendroctonus frontalis y dos especies de Ips (Coleoptera: Curculionidae en bosques de Chiapas, México Kairomonal response of coleopterans associated with Dendroctonus frontalis and two Ips species (Coleoptera: Curculionidae in forest of Chiapas, Mexico

    Directory of Open Access Journals (Sweden)

    Bernardo Domínguez-Sánchez

    2008-06-01

    Full Text Available Se evaluó la diversidad de escarabajos descortezadores y la respuesta diferencial de sus coleópteros asociados a feromonas comerciales de agregación, en bosques de pino del estado de Chiapas, México. Durante los meses de junio a octubre del 2006, se colocaron 40 trampas multiembudo tipo Lindgren cebadas con las feromonas racémicas frontalina, ipsenol e ipsdienol y un testigo (sin feromona. La captura fue más abundante para los escarabajos descortezadores Dendroctonus frontalis (Zimmermann con frontalina, y de Ips spp. con ipsenol e ipsdienol. Se registró respuesta kairomonal específica de los depredadores Temnochila chlorodia (Mannerheim, Enoclerus ablusus (Barr y Elacatis sp. hacia las feromonas de agregación. Tanto para descortezadores como para depredadores, las mayores abundancias fueron registradas durante el verano y a comienzos del otoño. Temmnochila chlorodia exhibió una atracción diferencial hacia los semioquímicos evaluados, mientras que E. ablusus, Elacatis sp. y Leptostylus sp. fueron atraídos principalmente por las feromonas ipsenol e ipsdienol. Además, por primera vez para México se determinó la respuesta kairomonal del fitófago Leptostylus sp. (Cerambycidae. Estos resultados indican que hay una comunicación intra e inter específica entre los escarabajos descortezadores y sus especies asociadas que promueven interacciones de competencia y depredación.We assessed the bark beetle diversity and the response of associated predators to aggregation pheromones in pine forests in Chiapas, Mexico. From June to October 2006, 40 Lindgren funnel traps were established with different baits that included frontalin, ipsenol and ipsdienol pheromones and a control (without pheromone. We registered the attractiveness of frontalin to the bark beetle Dendroctonus frontalis (Zimmermann, and ipsenol and ipsdienol to Ips spp. Kairomonal specific response of the predators Temnochila chlorodia (Mannerheim, Enoclerus ablusus (Barr and

  10. Using a kairomone-based attracting system to enhance biological control of mealybugs (Hemiptera: Pseudococcidae by Anagyrus sp. near pseudococci (Hymenoptera: Encyrtidae in Sicilian vineyards

    Directory of Open Access Journals (Sweden)

    Ramzi Mansour

    2010-11-01

    Full Text Available The “potato trap” technique was applied for the fi rst time in Italian (Sicily vineyards in an attempt to assess: a the impact of the kairomonal activity of the vine mealybug sex pheromone (S-(+-lavandulyl senecioate (LS on the parasitism of mealybugs by the encyrtid Anagyrus sp. near pseudococci, b the influence of two commonly used insecticides on the parasitization activity of A. sp. near pseudococci towards mealybugs, and c the efficiency of the release of A. sp. near pseudococci in enhancing parasitism rates of mealybugs. The number of captured A. sp. near pseudococci females in LS baited traps was significantly higher than that in unbaited traps. The minimal number of days for the first parasitoid emergence in LS baited traps was almost 3 days earlier, compared to unbaited control, suggesting a faster host detection by the encyrtid when LS is applied. These findings resulted in a significant increase in parasitism of mealybugs by A. sp. near pseudococci in LS baited traps relative to unbaited traps suggesting that the LS is used by the encyrtid as kairomone to ensure greater potential for host searching activity. Insecticide treatments significantly affected parasitization activity of A. sp. near pseudococci on mealybugs when compared to an untreated control with parasitoid release. The buprofezin, chlorpyriphos-methyl and untreated control with no parasitoid release treatments had statistically similar numbers of emerged parasitoids from exposed mealybugs. The obtained results provide evidence that, in the absence of conventional insecticides applications, the use of the LS could be a promising tool to improve and strengthen biological control of mealybugs by A. sp. near pseudococci within Sicilian vineyard conditions.

  11. Can false memory for critical lures occur without conscious awareness of list words?

    Science.gov (United States)

    Sadler, Daniel D; Sodmont, Sharon M; Keefer, Lucas A

    2018-02-01

    We examined whether the DRM false memory effect can occur when list words are presented below the perceptual identification threshold. In four experiments, subjects showed robust veridical memory for studied words and false memory for critical lures when masked list words were presented at exposure durations of 43 ms per word. Shortening the exposure duration to 29 ms virtually eliminated veridical recognition of studied words and completely eliminated false recognition of critical lures. Subjective visibility ratings in Experiments 3a and 3b support the assumption that words presented at 29 ms were subliminal for most participants, but were occasionally experienced with partial awareness by participants with higher perceptual awareness. Our results indicate that a false memory effect does not occur in the absence of conscious awareness of list words, but it does occur when word stimuli are presented at an intermediate level of visibility. Copyright © 2017 Elsevier Inc. All rights reserved.

  12. Interpreting Popov criteria in Lure´ systems with complex scaling stability analysis

    Science.gov (United States)

    Zhou, J.

    2018-06-01

    The paper presents a novel frequency-domain interpretation of Popov criteria for absolute stability in Lure´ systems by means of what we call complex scaling stability analysis. The complex scaling technique is developed for exponential/asymptotic stability in LTI feedback systems, which dispenses open-loop poles distribution, contour/locus orientation and prior frequency sweeping. Exploiting the technique for alternatively revealing positive realness of transfer functions, re-interpreting Popov criteria is explicated. More specifically, the suggested frequency-domain stability conditions are conformable both in scalar and multivariable cases, and can be implemented either graphically with locus plotting or numerically without; in particular, the latter is suitable as a design tool with auxiliary parameter freedom. The interpretation also reveals further frequency-domain facts about Lure´ systems. Numerical examples are included to illustrate the main results.

  13. Synchronization criterion for Lur'e type complex dynamical networks with time-varying delay

    International Nuclear Information System (INIS)

    Ji, D.H.; Park, Ju H.; Yoo, W.J.; Won, S.C.; Lee, S.M.

    2010-01-01

    In this Letter, the synchronization problem for a class of complex dynamical networks in which every identical node is a Lur'e system with time-varying delay is considered. A delay-dependent synchronization criterion is derived for the synchronization of complex dynamical network that represented by Lur'e system with sector restricted nonlinearities. The derived criterion is a sufficient condition for absolute stability of error dynamics between the each nodes and the isolated node. Using a convex representation of the nonlinearity for error dynamics, the stability condition based on the discretized Lyapunov-Krasovskii functional is obtained via LMI formulation. The proposed delay-dependent synchronization criterion is less conservative than the existing ones. The effectiveness of our work is verified through numerical examples.

  14. Multivariable PD controller design for fast chaos synchronization of Lur'e systems

    International Nuclear Information System (INIS)

    Wen, Guilin; Wang, Qing-Guo; He, Yong; Ye, Zhen

    2007-01-01

    In this Letter, a strategy for fast master-slave synchronization is proposed for Lur'e systems under PD control based on the free-weighting matrix approach and the S-procedure. The purpose of the derivative action is to improve the closed-loop stability and speed synchronization response. The proposed strategy covers the existing result for the proportional control alone as a special case. This approach is illustrated by the Chua's chaotic circuit system

  15. There is no magic fruit fly trap: multiple biological factors influence the response of adult Anastrepha ludens and Anastrepha obliqua (Diptera: Tephritidae) individuals to MultiLure traps baited with BioLure or NuLure.

    Science.gov (United States)

    Díaz-Fleischer, Francisco; Arredondo, José; Flores, Salvador; Montoya, Pablo; Aluja, Martín

    2009-02-01

    Field-cage experiments were performed to determine the effectiveness of MultiLure traps (Better World MFG Inc., Fresno, CA) baited with NuLure (Miller Chemical and Fertilizer Corp., Hanover, PA) or BioLure (Suterra LLC, Inc., Bend, OR) in capturing individually marked Mexican fruit fly, Anastrepha ludens (Loew), and West Indian fruit fly, Anastrepha obliqua (Macquart) (Diptera: Tephritidae), of both sexes. Experimental treatments involved wild and laboratory-reared flies of varying ages (2-4 and 15-18 d) and dietary histories (sugar only, open fruit, open fruit plus chicken feces, and hydrolyzed protein mixed with sugar). Data were divided into two parts: total captures over a 24-h period and trap visits/landings, entrances into interior of trap ,and effective captures (i.e., drowning in liquid bait or water) over a 5-h detailed observation period (0600-1100 hours). The response to the two baits varied by fly species, gender, physiological state, age, and strain. Importantly, there were several highly significant interactions among these factors, underlining the complex nature of the response. The two baits differed in attractiveness for A. obliqua but not A. ludens. The effect of strain (wild versus laboratory flies) was significant for A. ludens but not A. obliqua. For effect of dietary history, adults of both species, irrespective of sex, were significantly less responsive to both baits when fed on a mixture of protein and sugar when compared with adults fed the other diets. Finally, we confirmed previous observations indicating that McPhail-type traps are quite inefficient. Considering the total 24-h fly tenure in the cage, and independent of bait treatment and fly type (i.e., strain, adult diet, gender and age), of a total of 2,880 A. obliqua and 2,880 A. ludens adults released into the field cages over the entire study (15 replicates), only 564 (19.6%) and 174 (6%) individuals, respectively, were effectively caught. When only considering the 5-h detailed

  16. Decentralized Blended Acquisition

    NARCIS (Netherlands)

    Berkhout, A.J.

    2013-01-01

    The concept of blending and deblending is reviewed, making use of traditional and dispersed source arrays. The network concept of distributed blended acquisition is introduced. A million-trace robot system is proposed, illustrating that decentralization may bring about a revolution in the way we

  17. H∞ control of Lur'e systems with sector and slope restricted nonlinearities

    International Nuclear Information System (INIS)

    Park, Ju H.; Ji, D.H.; Won, S.C.; Lee, S.M.; Choi, S.J.

    2009-01-01

    This Letter considers H ∞ controller design scheme for Lur'e systems with sector/slope restrictions and external disturbance. Based on Lyapunov theory and linear matrix inequality (LMI) formulation, a state feedback controller is designed to not only guarantee stability of systems but also reduce the effect of external disturbance to an H ∞ norm constraint. The nonlinearities are expressed as convex combinations of sector and slope bounds so that equality constraints are converted into inequality constraints using convex properties of the nonlinear function. Then, the stabilizing feedback gain matrix is derived through LMI formulation. Finally, a numerical example shows the effectiveness of the proposed method.

  18. Evaluation of Food Lures for Capture and Monitoring of Anastrepha fraterculus (Diptera: Tephritidae) on Temperate Fruit Trees.

    Science.gov (United States)

    Rosa, J M da; Arioli, C J; Santos, J P Dos; Menezes-Netto, A C; Botton, M

    2017-06-01

    The Anastrepha fraterculus (Wiedemann) (Diptera: Tephritidae) is the main pest of fruit trees grown in temperate climates in the southern region of Brazil. The objective of this work was to evaluate the efficiency of the major commercial food lures used in Brazil for trapping and monitoring of A. fraterculus in plum, pear, and feijoa orchards. The assessed lures were hydrolyzed proteins of animal origin (CeraTrap) and plant origin (BioAnastrepha), torula yeast + borax (Torula), and grape juice. Response variables included the rate of adult capture (flies per trap per day, FTD) and the percentage of females captured. We also evaluated the number of times the weekly capture rate exceeded the traditional threshold of 0.5 FTD for each lure. Traps baited with grape juice, currently used for monitoring A. fraterculus in Southern Brazil, captured fewer adults and a lower percentage of females compared with the other lures. CeraTrap trapped a greater number of A. fraterculus adults and, in some cases, a lower percentage of females compared with the other lures in pears. Traps baited with CeraTrap had greater capture rates (FTD), particularly during the stages of fruit maturation and harvest, and even in years with low population density of A. fraterculus, thus demonstrating greater sensitivity in the detection of this pest. These results show that, in order to detect and monitor the presence of A. fraterculus in plum, feijoa, and pear crops, protein-based lures are superior to grape juice, especially the animal protein CeraTrap. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  19. Ulcere de Marjolin: complication redoutable des sequelles de brûlures

    Science.gov (United States)

    Ouahbi, S.; Droussi, H.; Boukind, S.; Dlimi, M.; Elatiqi, O.K.; Elamrani, M.D.; Benchamkha, Y.; Ettalbi, S.

    2013-01-01

    Summary L’ulcère de Marjolin désigne la transformation maligne d’une cicatrice de brûlure ou de toute autre plaie ou ulcération chronique. Le type histologique prédominant reste le carcinome épidermoïde, et il est caractérisé par son agressivité locale, des métastases plus fréquentes, un risque de récurrence et une mortalité plus importante que les carcinomes épidermoïdes classiques. Notre travail est une étude rétrospective portant sur 21 cas d’ulcère de Marjolin, colligés au service de chirurgie plastique du CHU Mohammed VI de Marrakech, avec pour but de relever les aspects épidémiologiques, thérapeutiques et évolutifs de cette pathologie. L’amélioration du pronostic nécessite non seulement un diagnostic et un traitement précoce, mais surtout une attitude préventive qui consiste en des greffes cutanées précoces et des soins réguliers de toute cicatrice de brûlure. PMID:24799850

  20. Entanglement in miscible blends

    Science.gov (United States)

    Watanabe, Hiroshi

    2010-03-01

    The entanglement length Le of polymer chains (corresponding to the entanglement molecular weight Me) is not an intrinsic material parameter but changes with the interaction with surrounding chains. For miscible blends of cis-polyisoprene (PI) and poly(tert-butyl styrene) (PtBS), changes of Le on blending was examined. It turned out that the Le averaged over the number fractions of the Kuhn segments of the components (PI and PtBS) satisfactorily describes the viscoelastic behavior of pseudo-monodisperse blends in which the terminal relaxation time is the same for PI and PtBS.

  1. MOOC Blended learning ontwikkelen

    NARCIS (Netherlands)

    Verjans, Steven

    2015-01-01

    Presentatie over het ontwerpen van leeractiviteiten (learning design) tijdens de zesde live sessie van de MOOC Blended learning ontwikkelen. Met gebruikmaking van presentatiematerialen van Diana Laurillard, Grainne Conole, Helen Beetham, Jos Fransen, Pieter Swager, Helen Keegan, Corinne Weisgerber.

  2. Fuel Property Blend Model

    Energy Technology Data Exchange (ETDEWEB)

    Pitz, William J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mehl, Marco [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wagnon, Scott J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zhang, Kuiwen [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kukkadapu, Goutham [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Westbrook, Charles K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-01-12

    The object of this project is to develop chemical models and associated correlations to predict the blending behavior of bio-derived fuels when mixed with conventional fuels like gasoline and diesel fuels.

  3. Blending into the mix

    Energy Technology Data Exchange (ETDEWEB)

    Adams, R.G.; Gibb, W.H.; Majid, K.A. [Power Technology (United Kingdom)

    1999-07-01

    Successful coal blending requires finding a careful balance between fuel costs and plant performance. A recent study of a Malaysian power plant shows how the utility (Tenaga Nasional Berhad (TNB)) could reduce fuel costs while avoiding boiler operating problems normally associated with firing low-grade coals. TNB`s Kaper 2220 MW power station in Selangor needed an improved method of coal blending for two new 500 MW units and for two existing 300 MW units. UK`s Power Technology was commissioned to identify what coal blends the boiler could tolerate. A Coal Quality Impact Model (CQIM) analysis of the effect of different coals and coal blends on combustion performance and economics, and a performance analysis of coal yard handling facility was made to determine whether the accuracy of the required blend could be achieved (using a Coal Handling Simulation, CHAS, software package). The CQIM study showed that the proportion of cheaper coals could be increased from 20% to 50% provided each shipment was adequately sampled. The CHAS study showed that use of a flat back reclaimer or modifications to the dry coal stove would allow accurate blending. 5 figs., 1 tab.

  4. Geographic variation in sexual attraction of Spodoptera frugiperda corn- and rice-strain males to pheromone lures

    NARCIS (Netherlands)

    Unbehend, M.; Hänniger, S.; Vásquez, G.M.; Juárez, M.L.; Reisig, D.; McNeil, J.N.; Meagher, R.L.; Jenkins, D.A.; Heckel, D.G.; Groot, A.T.

    2014-01-01

    The corn- and rice-strains of Spodoptera frugiperda exhibit several genetic and behavioral differences and appear to be undergoing ecological speciation in sympatry. Previous studies reported conflicting results when investigating male attraction to pheromone lures in different regions, but this

  5. COMPARING THE EFFECTIVENESS RATIOS OF PHEROMONE LURES OF IPSOWIT® ,IPSTYP®, AND TYPOSAN® AGAINST IPS TYPOGRAPHUS (L. (COL.: SCOLYTIDAE

    Directory of Open Access Journals (Sweden)

    Temel Göktürk

    2005-04-01

    Full Text Available In this study, effectiveness ratios of Ipsowit®, Ipstyp®, and Typosan® pheromone lures were compared. One research area within the pure spruce forests of Ardanuç-Karanlıkmeşe in Artvin Province of Turkey was selected for this study. A total of 30 pheromone traps (with ten of each type of pheromone lures were placed in the area. The traps hunging in the third week of May in 2003 stayed for 45 days. All of them were checked four times in 45 days to count trapped insects. As a result, in the early weeks of the placement, there were more insects collected, followed by a gradual decrease in trapped insect number in the later weeks. Furthermore, there was no significant difference between Ipstyp® and Typosan® in number of trapped insects. Both pheromone lures were, however, much more effective than Ipsowit®That is why, instead of Ipsowit®, using Ipstyp® and/or Typosan® lures against the pest would be more economic and more effective.

  6. Effects of light and presence of fish on lure display and larval release behaviours in two species of freshwater mussels

    Science.gov (United States)

    Wendell R. Haag; Melvin L. Warren

    2000-01-01

    We investigated how two sympatric species of freshwater mussels transmit their parasitic larvae to fish hosts. We found that Villosa nebulosa and V. vibex both display large mantle lures to attract potential host fish, but V. nebulosa displayed only at night and V....

  7. Attraction of pollinators to atemoya (Magnoliales: Annonaceae) in Puerto Rico: a synergistic approach using multiple nitidulid lures.

    Science.gov (United States)

    Jenkins, David A; Cline, Andrew R; Irish, Brian; Goenaga, Ricardo

    2013-02-01

    Atemoya, a hybrid between Annona squamosa (L.) and A. cherimola Miller (Annonaceae), has potential to be a major fruit crop in tropical and subtropical areas. A major setback to fruit production throughout the world is low fruit-set because of inadequate pollinator visits, typically Nitidulidae beetles. We identified beetle visitors to atemoya flowers in an orchard in Puerto Rico and used Universal moth traps to monitor the attractiveness of two commercially available Nitidulidae lures. The most common visitors to atemoya flowers were an unidentified Europs species (Coleoptera: Monotomidae), followed by Loberus testaceus (Coleoptera: Erotylidae), neither of which have been previously reported as visitors to Annona flowers. The commercial lures attracted few or no beetles when used separately, but attracted a large number of beetles, especially Carpophilus dimidiatus (Coleoptera: Nitidulidae) and Europs, when used in combination. This attraction is synergistic and increases with dose at the doses assayed (0-4 lures), and decreases over time with >50% of trap captures occurring in the first week and no beetles collected after 5 wk. This is the first report of aggregation pheromone lures in nitidulids acting synergistically to attract other species, including beetles not in the Nitidulidae. The results are discussed as they pertain to increasing fruit set, as well as the potential for altering fruit size and shape in atemoya.

  8. Geographic variation in sexual attraction of Spodoptera frugiperda corn- and rice-strain males to pheromone lures

    Science.gov (United States)

    The corn- and rice-strains of Spodoptera frugiperda exhibit several genetic and behavioral differences and appear to be undergoing ecological speciation in sympatry. Previous studies reported conflicting results when investigating male attraction to pheromone lures in different regions, but this cou...

  9. Mass Communications as a Vehicle to Lure Russian Émigrés Homeward

    Directory of Open Access Journals (Sweden)

    Simo Mikkonen

    2011-04-01

    Full Text Available After the millions of wartime displaced citizens had been forcibly returned to the Soviet Union after the Second World War, the Soviet Union inaugurated a new type of campaign in the mid-1950s to get all the remaining Soviet citizens and former émigrés from Sovietoccupied areas to migrate back. In this campaign, the Soviets used all the means of mass communication they were able to produce, especially radio combined with the press and direct contact with people. The campaign was not very successful, at least not among the people it was supposed to lure back: people residing in Europe. However, many people, especially from Latin America, migrated back to the Soviet Union, only to be disappointed, just as the people who had migrated to the Soviet Union in the early 1930s.

  10. An unprecedented role reversal: ground beetle larvae (Coleoptera: Carabidae lure amphibians and prey upon them.

    Directory of Open Access Journals (Sweden)

    Gil Wizen

    Full Text Available Amphibians often feed on beetle larvae, including those of ground beetles (Carabidae. Preliminary reports have detailed an unusual trophic interaction in which, in contrast, larvae of the ground beetle Epomis prey upon juvenile and adult amphibians. While it is known that these larvae feed exclusively on amphibians, how the predator-prey encounter occurs to the advantage of the beetle larvae had been unknown to date. Using laboratory observations and controlled experiments, we recorded the feeding behavior of Epomis larvae, as well as the behavior of their amphibian prey. Here we reveal that larvae of two species of Epomis (E. circumscriptus and E. dejeani lure their potential predator, taking advantage of the amphibian's predation behavior. The Epomis larva combines a sit-and-wait strategy with unique movements of its antennae and mandibles to draw the attention of the amphibian to the presence of a potential prey. The intensity of this enticement increases with decreasing distance between the larva and the amphibian. When the amphibian attacks, the larva almost always manages to avoid the predator's protracted tongue, exploiting the opportunity to attach itself to the amphibian's body and initiate feeding. Our findings suggest that the trophic interaction between Epomis larvae and amphibians is one of the only natural cases of obligatory predator-prey role reversal. Moreover, this interaction involves a small insect larva that successfully lures and preys on a larger vertebrate. Such role reversal is exceptional in the animal world, extending our perspective of co-evolution in the arms race between predator and prey, and suggesting that counterattack defense behavior has evolved into predator-prey role reversal.

  11. Supporting School Leaders in Blended Learning with Blended Learning

    Science.gov (United States)

    Acree, Lauren; Gibson, Theresa; Mangum, Nancy; Wolf, Mary Ann; Kellogg, Shaun; Branon, Suzanne

    2017-01-01

    This study provides a mixed-methods case-study design evaluation of the Leadership in Blended Learning (LBL) program. The LBL program uses blended approaches, including face-to-face and online, to prepare school leaders to implement blended learning initiatives in their schools. This evaluation found that the program designers effectively…

  12. Blended Learning Design

    DEFF Research Database (Denmark)

    Pedersen, Lise

    2015-01-01

    University College Lillebaelt has decided that 30 percent of all educational elements must be generated as blended learning by the end of the year 2015 as part of a modernization addressing following educational needs: 1. Blended learning can help match the expectations of the future students who...... learning. 4. Blended learning can contribute to supporting and improving efficiency of educational efforts. This can for instance be done through programmes for several classes by using video conferencing, allocating traditional face to face teaching to synchronous and asynchronous study activities produce...... digital materials which can be employed didactically and reused by the teachers. This can also mean that the particular competencies which teaches have in Svendborg can be used at other locations in UCL and disseminated to a larger group of students without further costs. Educational Innovation...

  13. AKRO/SF: Blend System

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Blend was the system used by the NMFS Alaska Regional Office to monitor groundfish catch from 1991 until 2002. The Blend system combined data from industry...

  14. Blended Learning over Two Decades

    Science.gov (United States)

    Zhonggen, Yu; Yuexiu, Zhejiang

    2015-01-01

    The 21st century has witnessed vast amounts of research into blended learning since the conception of online learning formed the possibility of blended learning in the early 1990s. The theme of this paper is blended learning in mainstream disciplinary communities. In particular, the paper reports on findings from the last two decades which looked…

  15. Morphology stabilization of heterogeneous blends

    International Nuclear Information System (INIS)

    1980-01-01

    A heterogeneous elastomer blend is described, consisting of at least two elastomer components which are cross-linkable by irradiation and having a stabilized morphology formed by subjecting the blend to high energy radiation to a point from below to slightly above the gel dose of the blend. (author)

  16. Locally restricted blending of Blobtrees

    NARCIS (Netherlands)

    Groot, de Erwin; Wyvill, B.; Wetering, van de H.M.M.

    2009-01-01

    Blobtrees are volume representations particularly useful for models which require smooth blending. When blending is applied to two or more Blobtree models, extra volume will be created in between the two surfaces to form a smooth connection. Although it is easy to apply blending, it is hard to

  17. Studies of PVC/ENR blends: blend compositions

    International Nuclear Information System (INIS)

    Chantara Thevy Ratnam; Khairul Zaman Mohd Dahlan; Nasir, M.; Baharin, A.

    2002-01-01

    Blends of poly(vinyl chloride/epoxidized natural rubber (PVC/ENR) were prepared by using Bra bender Plasticorder at compositions ranging from 0-100% PVC. They were blended at 150 degree C mixing temperature, 50 rpm rotor speed and 10 minutes mixing time. The blends were characterized for tensile strength , elongation at break, glass transition temperatures and Fourier transform infra red spectroscopy (FTIR). Results revealed that as the PVC content increases the blend behaviour changes from elastomeric to glassy. However the blends found to be compatible at all compositions. (Author)

  18. On technology blending.

    OpenAIRE

    Rosenberg N

    1986-01-01

    ILO pub-WEP pub. Working paper on the blending of traditional technology and technological change in developing countries - argues that choice of technology should be compatible with labour intensive requirements and local level management and economic conditions; considers employment creation and economic implications; concludes that technology transfer should be selective. References.

  19. Apparatus for blending small particles

    International Nuclear Information System (INIS)

    Bradley, R.A.; Reese, C.R.; Sease, J.D.

    1975-01-01

    An apparatus is described for blending small particles and uniformly loading the blended particles in a receptacle. Measured volumes of various particles are simultaneously fed into a funnel to accomplish radial blending and then directed onto the apex of a conical splitter which collects the blended particles in a multiplicity of equal subvolumes. Thereafter the apparatus sequentially discharges the subvolumes for loading in a receptacle. A system for blending nuclear fuel particles and loading them into fuel rod molds is described in a preferred embodiment

  20. Blended learning in anatomy

    DEFF Research Database (Denmark)

    Østergaard, Gert Værge; Brogner, Heidi Marie

    behind DBR is that new knowledge is generated through processes that simultaneously develop, test and improve a design, in this case, an educational design (1) The main principles used in the project is blended learning and flipped learning (2). …"I definitely learn best in practice, but the theory...... in working with the assignments in the classroom."... External assesor, observer and interviewer Based on the different evaluations, the conclusion are that the blended learning approach combined with the ‘flipped classroom’ is a very good way to learn and apply the anatomy, both for the students......The aim of the project was to bridge the gap between theory and practice by working more collaboratively, both peer-to-peer and between student and lecturer. Furthermore the aim was to create active learning environments. The methodology of the project is Design-Based Research (DBR). The idea...

  1. Theory of polymer blends

    International Nuclear Information System (INIS)

    Curro, J.G.; Schweizer, K.S.

    1989-01-01

    We have recently developed a new theoretical approach to the study of polymer liquids. The theory is based on the ''reference interaction site model'' (RISM theory) of Chandler and Andersen, which has been successful in describing the structure of small molecule liquids. We have recently extended our polymer RISM theory to the case of polymer blends. In the present investigation we have applied this theory to two special binary blends: (1) the athermal mixture where we isolate structural effects, and (2) the isotopic mixture in which structurally identical polymer chains interact with dissimilar attractive interactions. By studying these two special cases we are able to obtain insights into the molecular factors which control the miscibility in polymer mixtures. 18 refs., 2 figs

  2. Response of Anastrepha suspensa to liquid protein baits and synthetic lure formulations

    International Nuclear Information System (INIS)

    Epsky, Nancy D.; Kendra, Paul E.; Heath, Robert R.

    2006-01-01

    Traps baited with AAPt captured more A. suspensa than traps baited with ABPt even when the ammonia release rates were similar. Reducing dosage of ammonia by 50% of the commercially available AA lure slightly increased female capture, but reducing dosage to 25% tended to decrease female capture. The 5% CPH/3% borax bait captured the same number of flies as TYB, and was more effective than 10% CPH/3% borax. Further decreasing the amount of borax added to CPH may improve its effectiveness. As has been observed in field tests, fresh TYB captures more A. suspensa than fresh Nulure/borax but this difference decreases as the bait solutions age. EAG analysis indicates that volatiles from fresh Nulure/ borax elicit a higher antennal response than TYB, but this difference decreases as the TYB solution ages. Chemical analysis will be needed to determine the nature of reduced capture by fresh Nulure/borax and to identify additional attractive chemicals emitted by these protein baits. (author)

  3. Response of Anastrepha suspensa to liquid protein baits and synthetic lure formulations

    Energy Technology Data Exchange (ETDEWEB)

    Epsky, Nancy D.; Kendra, Paul E.; Heath, Robert R., E-mail: Nancy.Epsky@ars.usda.go, E-mail: Paul.Kendra@ars.usda.go, E-mail: Bob.Heath@ars.usda.go [U.S. Department of Agriculture (USDA/ARS/SHRS), Miami, FL (United States). Agricultural Research Service. Subtropical Horticulture Research Station

    2006-07-01

    Traps baited with AAPt captured more A. suspensa than traps baited with ABPt even when the ammonia release rates were similar. Reducing dosage of ammonia by 50% of the commercially available AA lure slightly increased female capture, but reducing dosage to 25% tended to decrease female capture. The 5% CPH/3% borax bait captured the same number of flies as TYB, and was more effective than 10% CPH/3% borax. Further decreasing the amount of borax added to CPH may improve its effectiveness. As has been observed in field tests, fresh TYB captures more A. suspensa than fresh Nulure/borax but this difference decreases as the bait solutions age. EAG analysis indicates that volatiles from fresh Nulure/ borax elicit a higher antennal response than TYB, but this difference decreases as the TYB solution ages. Chemical analysis will be needed to determine the nature of reduced capture by fresh Nulure/borax and to identify additional attractive chemicals emitted by these protein baits. (author)

  4. Improvement of a synthetic lure for Anopheles gambiae using compounds produced by human skin microbiota

    NARCIS (Netherlands)

    Verhulst, N.O.; Mbadi, P.A.; Bukovinszkine-Kiss, G.; Mukabana, W.R.; Loon, van J.J.A.; Takken, W.; Smallegange, R.C.

    2011-01-01

    Background - Anopheles gambiae sensu stricto is considered to be highly anthropophilic and volatiles of human origin provide essential cues during its host-seeking behaviour. A synthetic blend of three human-derived volatiles, ammonia, lactic acid and tetradecanoic acid, attracts A. gambiae. In

  5. Synthesizing optimal waste blends

    International Nuclear Information System (INIS)

    Narayan, V.; Diwekar, W.M.; Hoza, M.

    1996-01-01

    Vitrification of tank wastes to form glass is a technique that will be used for the disposal of high-level waste at Hanford. Process and storage economics show that minimizing the total number of glass logs produced is the key to keeping cost as low as possible. The amount of glass produced can be reduced by blending of the wastes. The optimal way to combine the tanks to minimize the vole of glass can be determined from a discrete blend calculation. However, this problem results in a combinatorial explosion as the number of tanks increases. Moreover, the property constraints make this problem highly nonconvex where many algorithms get trapped in local minima. In this paper the authors examine the use of different combinatorial optimization approaches to solve this problem. A two-stage approach using a combination of simulated annealing and nonlinear programming (NLP) is developed. The results of different methods such as the heuristics approach based on human knowledge and judgment, the mixed integer nonlinear programming (MINLP) approach with GAMS, and branch and bound with lower bound derived from the structure of the given blending problem are compared with this coupled simulated annealing and NLP approach

  6. Improvement of a synthetic lure for Anopheles gambiae using compounds produced by human skin microbiota.

    Science.gov (United States)

    Verhulst, Niels O; Mbadi, Phoebe A; Kiss, Gabriella Bukovinszkiné; Mukabana, Wolfgang R; van Loon, Joop J A; Takken, Willem; Smallegange, Renate C

    2011-02-08

    Anopheles gambiae sensu stricto is considered to be highly anthropophilic and volatiles of human origin provide essential cues during its host-seeking behaviour. A synthetic blend of three human-derived volatiles, ammonia, lactic acid and tetradecanoic acid, attracts A. gambiae. In addition, volatiles produced by human skin bacteria are attractive to this mosquito species. The purpose of the current study was to test the effect of ten compounds present in the headspace of human bacteria on the host-seeking process of A. gambiae. The effect of each of the ten compounds on the attractiveness of a basic blend of ammonia, lactic and tetradecanoic acid to A. gambiae was examined. The host-seeking response of A. gambiae was evaluated in a laboratory set-up using a dual-port olfactometer and in a semi-field facility in Kenya using MM-X traps. Odorants were released from LDPE sachets and placed inside the olfactometer as well as in the MM-X traps. Carbon dioxide was added in the semi-field experiments, provided from pressurized cylinders or fermenting yeast. The olfactometer and semi-field set-up allowed for high-throughput testing of the compounds in blends and in multiple concentrations. Compounds with an attractive or inhibitory effect were identified in both bioassays. 3-Methyl-1-butanol was the best attractant in both set-ups and increased the attractiveness of the basic blend up to three times. 2-Phenylethanol reduced the attractiveness of the basic blend in both bioassays by more than 50%. Identification of volatiles released by human skin bacteria led to the discovery of compounds that have an impact on the host-seeking behaviour of A. gambiae. 3-Methyl-1-butanol may be used to increase mosquito trap catches, whereas 2-phenylethanol has potential as a spatial repellent. These two compounds could be applied in push-pull strategies to reduce mosquito numbers in malaria endemic areas.

  7. Blended acquisition with dispersed source arrays

    NARCIS (Netherlands)

    Berkhout, A.J.

    2012-01-01

    Blended source arrays are historically configured with equal source units, such as broadband vibrators (land) and broadband air-gun arrays (marine). I refer to this concept as homogeneous blending. I have proposed to extend the blending concept to inhomogeneous blending, meaning that a blended

  8. Improving the delivery and efficiency of fungus-impregnated cloths for control of adult Aedes aegypti using a synthetic attractive lure.

    Science.gov (United States)

    Paula, Adriano R; Silva, Leila E I; Ribeiro, Anderson; Butt, Tariq M; Silva, Carlos P; Samuels, Richard I

    2018-05-04

    Entomopathogenic fungi are highly promising agents for controlling Aedes aegypti mosquitoes. Deploying fungus-impregnated black cloths in PET traps efficiently reduced Ae. aegypti female survival rates under intra-domicile conditions. With the aim of further increasing the effectiveness of the traps, the addition of attractive lures to fungus-impregnated traps was evaluated. Black cloths were suspended inside 2 l plastic bottles called "PET traps". These traps were placed in rooms simulating human residences. The first experiments evaluated the attraction of mosquitoes to PET traps with black cloths covered in adhesive film with and without synthetic lures (AtrAedes™). Traps were left in the test rooms for either 24 or 48 h. The attractiveness of the lures over time was also evaluated. The efficiency of PET traps with fungus-impregnated black cloths associated with lures was compared to that of traps without lures. The highest percentage of captured mosquitoes (31 and 66%) were observed in PET traps with black cloths covered in adhesive film + attractive lure maintained in test rooms for 24 h and 48 h, respectively. Black cloths covered in adhesive film captured 17 or 36% of the mosquitoes at 24 h and 48 h, respectively. The attractiveness of the lures fell gradually over time, capturing 37% after 5 days on the bench and 22% of the mosquitoes after 30 days exposure to ambient conditions. Associating attractive synthetic lures with black cloths impregnated with M. anisopliae placed in test rooms for 120 h reduced mean survival to 32%, whilst black cloths impregnated with M. anisopliae without lures resulted in a 48% survival rate. Using Beauveria bassiana in the traps resulted in a 52% reduction in mosquito survival, whilst combining Beauveria and AtrAedes resulted in a 36% survival rate. PET traps impregnated with fungus + AtrAedes resulted in similar reductions in survival when left in the rooms for 24, 48, 72 or 120 h. AtrAedes increased attractiveness of PET

  9. Synthetic sex pheromone in a long-lasting lure attracts the visceral leishmaniasis vector, Lutzomyia longipalpis, for up to 12 weeks in Brazil.

    Directory of Open Access Journals (Sweden)

    Daniel P Bray

    2014-03-01

    Full Text Available Current control methodologies have not prevented the spread of visceral leishmaniasis (VL across Brazil. Here, we describe the development of a new tool for controlling the sand fly vector of the disease: a long-lasting lure, which releases a synthetic male sex pheromone, attractive to both sexes of Lutzomyia longipalpis. This device could be used to improve the effectiveness of residual insecticide spraying as a means of sand fly control, attracting L. longipalpis to insecticide-treated animal houses, where they could be killed in potentially large numbers over a number of weeks. Different lure designs releasing the synthetic pheromone (±-9-methylgermacrene-B (CAS 183158-38-5 were field-tested in Araçatuba, São Paulo (SP. Experiments compared numbers of sand flies caught overnight in experimental chicken sheds with pheromone lures, to numbers caught in control sheds without pheromone. Prototype lures, designed to last one night, were first used to confirm the attractiveness of the pheromone in SP, and shown to attract significantly more flies to test sheds than controls. Longer-lasting lures were tested when new, and at fortnightly intervals. Lures loaded with 1 mg of pheromone did not attract sand flies for more than two weeks. However, lures loaded with 10 mg of pheromone, with a releasing surface of 15 cm2 or 7.5 cm2, attracted female L. longipalpis for up to ten weeks, and males for up to twelve weeks. Approximately five times more sand flies were caught with 7.5 cm2 10 mg lures when first used than occurred naturally in non-experimental chicken resting sites. These results demonstrate that these lures are suitably long-lasting and attractive for use in sand fly control programmes in SP. To our knowledge, this is the first sex pheromone-based technology targeting an insect vector of a neglected human disease. Further studies should explore the general applicability of this approach for combating other insect-borne diseases.

  10. Success of capture of toads improved by manipulating acoustic characteristics of lures.

    Science.gov (United States)

    Muller, Benjamin J; Schwarzkopf, Lin

    2017-11-01

    Management of invasive vertebrates is a crucial component of conservation. Trapping reproductive adults is often effective for control, and modification of traps may greatly increase their attractiveness to such individuals. Cane toads (Rhinella marina) are invasive, and males use advertisement vocalisations to attract reproductive females. In amphibians, including toads, specific structural parameters of calls (e.g. dominant frequency and pulse rate) may be attractive to females. Some cane toad traps use an artificial advertisement vocalisation to attract toads. We determined whether variation of the call's parameters (volume, dominant frequency and pulse rate) could increase the capture rate of gravid females. Overall, traps equipped with loud calls (80 dB at 1 m) caught significantly more toads, and proportionally more gravid females, than traps with quiet calls (60 dB at 1 m), and traps with low dominant frequency calls caught more gravid females than traps with median frequency calls. Traps with high pulse rate calls attracted more females than traps with low pulse rate calls. Approximately 91% of the females trapped using a low frequency and high pulse rate combination call were gravid, whereas in traps using a call with population median parameters only approximately 75% of captured females were gravid. Calls that indicated large-bodied males (low frequency) with high energy reserves (high pulse rate) are often attractive to female anurans and were effective lures for female toads in our study. The design of future trapping regimes should account for behavioural preferences of the target sex. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  11. Responses of Neomegalotomus parvus (Hemiptera: Alydidae to color and male-lured traps

    Directory of Open Access Journals (Sweden)

    Maurício Ursi Ventura

    2004-08-01

    Full Text Available In 1998, the relative responses of Neomegalotomus parvus (Westwood (Hemiptera: Alydidae to colors in traps were assessed in the field. Colors were printed in white alkaline paper and covered with transparent plastic. Printed colors were black, green, yellow, red and blue. Treatments also included white paper and aluminum foil. Green traps captured more bugs than the other traps (except yellow. Yellow traps caught significantly more N. parvus males than blue, black and aluminum traps. White, red and blue traps captured significantly more N. parvus males than black traps. In 1999, the same treatments were used and additionally included the factor presence (X absence of males in cages in the traps. Four males were confined in the cages together with pigeon pea seeds and water. Control traps received only pigeon pea seeds and water. No responses were found for color comparisons. Male-lured traps captured significantly more males than control traps.Em 1998, as respostas relativas de Neomegalotomus parvus (Westwood (Hemiptera: Alydidae a cores em armadilhas foram avaliadas no campo. As cores foram impressas (preto, verde, amarelo, vermelho e azul, em papel alcalino branco e coberto com plástico transparente. Também se incluiu papel branco e folha de alumínio, como tratamentos. Armadilhas verdes capturaram mais insetos que outras armadilhas (exceto amarelo. Armadilhas amarelas capturaram significativamente mais machos de N. parvus do que armadilhas azuis, pretas e alumínio. Armadilhas brancas, vermelhas e azuis capturaram significativamente mais machos de N. parvus do que armadilhas pretas. Em 1999, os mesmos tratamentos foram usados e também se incluiu fator presença (X ausência de machos em gaiolas nas armadilhas. Quatro machos foram confinados nas gaiolas junto com sementes de guandu e água. Testemunhas receberam somente sementes de guandu e água. Não foram obtidas respostas significativas à cores. Armadilhas com machos capturaram

  12. Blended Learning on Campus

    DEFF Research Database (Denmark)

    Heilesen, Simon; Nielsen, Jørgen Lerche

    2004-01-01

    On the basis of a large-scale project implementing information and communication technology at Roskilde University, Denmark, this paper discusses ways of introducing technology-based blended learning in academic life. We examine some examples of use of systems for computer-mediated collabora......-tive learning and work in Danish Open University education as well as in courses on campus. We further suggest some possi-bilities for using technology in innovative ways, arguing that innovation is to be found, not in isolated instantiations of sys-tems, but in the form of a deliberate integration of all...... relevant ICT-features as a whole into the learning environment....

  13. Blended Learning Design

    DEFF Research Database (Denmark)

    Pedersen, Lise

    2015-01-01

    learning. 4. Blended learning can contribute to supporting and improving efficiency of educational efforts. This can for instance be done through programmes for several classes by using video conferencing, allocating traditional face to face teaching to synchronous and asynchronous study activities produce...... digital materials which can be employed didactically and reused by the teachers. This can also mean that the particular competencies which teaches have in Svendborg can be used at other locations in UCL and disseminated to a larger group of students without further costs. Educational Innovation...

  14. Classifying K-12 Blended Learning

    Science.gov (United States)

    Staker, Heather; Horn, Michael B.

    2012-01-01

    The growth of online learning in the K-12 sector is occurring both remotely through virtual schools and on campuses through blended learning. In emerging fields, definitions are important because they create a shared language that enables people to talk about the new phenomena. The blended-learning taxonomy and definitions presented in this paper…

  15. Blended Learning: An Innovative Approach

    Science.gov (United States)

    Lalima; Dangwal, Kiran Lata

    2017-01-01

    Blended learning is an innovative concept that embraces the advantages of both traditional teaching in the classroom and ICT supported learning including both offline learning and online learning. It has scope for collaborative learning; constructive learning and computer assisted learning (CAI). Blended learning needs rigorous efforts, right…

  16. Blended Learning: A Dangerous Idea?

    Science.gov (United States)

    Moskal, Patsy; Dziuban, Charles; Hartman, Joel

    2013-01-01

    The authors make the case that implementation of a successful blended learning program requires alignment of institutional, faculty, and student goals. Reliable and robust infrastructure must be in place to support students and faculty. Continuous evaluation can effectively track the impact of blended learning on students, faculty, and the…

  17. Empowering Learners through Blended Learning

    Science.gov (United States)

    Owston, Ron

    2018-01-01

    Blended learning appears to facilitate learner empowerment more readily than either face-to-face or fully online courses. This contention is supported by a review of literature on the affordances of blended learning that support Thomas and Velthouse's (1990) four conditions of empowerment: choice, meaningfulness, competence, and impact. Blended…

  18. The Basics of Blended Instruction

    Science.gov (United States)

    Tucker, Catlin R.

    2013-01-01

    Even though many of teachers do not have technology-rich classrooms, the rapidly evolving education landscape increasingly requires them to incorporate technology to customize student learning. Blended learning, with its mix of technology and traditional face-to-face instruction, is a great approach. Blended learning combines classroom learning…

  19. New delay-dependent absolute stability criteria for Lur'e systems with time-varying delay

    Science.gov (United States)

    Chen, Yonggang; Bi, Weiping; Li, Wenlin

    2011-07-01

    In this article, the absolute stability problem is investigated for Lur'e systems with time-varying delay and sector-bounded nonlinearity. By employing the delay fractioning idea, the new augmented Lyapunov functional is first constructed. Then, by introducing some slack matrices and by reserving the useful term when estimating the upper bound of the derivative of Lyapunov functional, the new delay-dependent absolute stability criteria are derived in terms of linear matrix inequalities. Several numerical examples are presented to show the effectiveness and the less conservativeness of the proposed method.

  20. Profiling Student Behaviour in a Blended Course: Closing the Gap Between Blended Teaching and Blended Learning

    NARCIS (Netherlands)

    Bos, Nynke; Brand-Gruwel, Saskia

    2018-01-01

    Blended learning is often associated with student-oriented learning in which students have varying degrees of control over their learning process. However, the current notion of blended learning is often a teacher- oriented approach in which the teacher identifies the used learning technologies and

  1. Blend or not to blend: a study investigating faculty members perceptions of blended teaching

    Directory of Open Access Journals (Sweden)

    Mehmet A Ocak

    2010-12-01

    Full Text Available This study examined faculty members’ perceptions of blended teaching from several perspectives. A total of 73 faculty members in Turkish Higher Education context participated in the study by completing an online survey that combined quantitative and qualitative approaches. Based on a data analysis, the faculty members’ perceptions were sorted into six categories: (a satisfaction with blended teaching, (b perceived impact on the role of the faculty, (c perceived impact on student learning, (d perceived impact on student motivation, (e advantages of blended teaching, and (f disadvantages of blended teaching. Findings indicated that faculty members were likely to agree that blended teaching provides a high degree of satisfaction and that it requires more time and commitment from the faculty. The faculty members perceived that blended teaching improves student learning and, to some extent, improves motivation. The faculty members also emphasized the importance of institutional support and the use of technology to mitigate student problems. This study presents these faculty members’ perceptions, which are helpful for those planning to implement a blended teaching approach, and makes suggestions for trouble-shooting and taking advantage of the opportunities in a blended environment successfully.

  2. Colour polymorphic lures exploit innate preferences for spectral versus luminance cues in dipteran prey.

    Science.gov (United States)

    White, Thomas E; Kemp, Darrell J

    2017-08-14

    Theory predicts that colour polymorphism may be favored by variation in the visual context under which signals are perceived. The context encompasses all environmental determinants of light availability and propagation, but also the dynamics of perception in receivers. Color vision involves the neural separation of information into spectral versus luminance channels, which often differentially guide specific tasks. Here we explicitly tested whether this discrete perceptual basis contributes to the maintenance of polymorphism in a prey-luring system. The orb-weaving spider Gasteracantha fornicata is known to attract a broad community of primarily dipteran prey due to their conspicuous banded dorsal signal. They occur in two morphs ("white" and "yellow") which should, respectively, generate greater luminance and color contrast in the dipteran eye. Given that arthropods often rely upon luminance-versus-spectral cues for relatively small-versus-large stimulus detection, we predicted a switch in relative attractiveness among morphs according to apparent spider size. Our experimental tests used colour-naïve individuals of two known prey species (Drosophila hydei and Musca domestica) in replicate Y-maze choice trials designed to manipulate the apparent size of spider models via the distance at which they are viewed. Initial trials confirmed that flies were attracted to each G. fornicata morph in single presentations. When given a simultaneous choice between morphs against a viewing background typical of those encountered in nature, flies exhibited no preference regardless of the visual angle subtended by models. However, when backgrounds were adjusted to nearer the extremes of those of each morph in the wild, flies were more attracted by white morphs when presented at longer range (consistent with a reliance on achromatic cues), yet were unbiased in their close-range choice. While not fully consistent with predictions (given the absence of a differential preference for

  3. The attraction of Zonocerus variegatus (Orthoptera: Pyrgomorphidae to different types of lure

    Directory of Open Access Journals (Sweden)

    A. Babatunde Idowu

    2001-06-01

    Full Text Available Zonocerus variegatus is a common grasshopper in parts of west and equtorial Africa.The distribution in Nigeria extends from the lowland rainforest zone to the savannah in the north. The influence of lure on the behaviour of grasshopper inside cages (120 insect per cage was investigated. Nymphs and adults of Zonocerus variegatus responded positively to intact leaves,crushed leaves and inflorescence of the common compositae weed Chromolaena odorata inside muslin bags, and intact plants. There were significant differences in the attraction recorded for starved nymphs, fed nymphs and starved adults. Attraction was more to intact leaves and is by olfaction. The increase in the attraction of starved nymphs is time dependent. Attraction to plant parts ceased after the plants were dried for 24 and 48 hours at room temperature and when plants were placed in transparent polythene bags. Gut motility and gut activity were higher during the day than at night. Nymphs, adults and egg pods placed separately inside muslin bags were not attractive to adults or nymphs.Zococerus variegatus es un saltamontes común en partes de Africa ecuatorial y oeste. La distribución en Nigeria se extiende desde la zona baja del bosque lluvioso hasta la sabana en el norte. La influencia del cebo sobre el comportamiento del saltamontes dentro de las jaulas (120 insectos por jaula fue investigada. Las ninfas y los adultos de Z. variegatus respondieron positivamente a hojas intactas, hojas aplastadas e inflorescencias de la hierba común compuesta Chromolaena odorata dentro de bolsas de muselina y a plantas intactas. Hubo diferencias significativas en la atracción registrada en ninfas mantenidas con hambre, ninfas alimentadas y adultos mantenidos con hambre. La atracción fue más hacia hojas intactas y fue por olfato. El aumento en la atracción de ninfas mantenidas con hambre fue tiempo-dependiente. La atracción a partes de plantas paró luego de que las plantas fueron secadas

  4. Method to blend separator powders

    Science.gov (United States)

    Guidotti, Ronald A.; Andazola, Arthur H.; Reinhardt, Frederick W.

    2007-12-04

    A method for making a blended powder mixture, whereby two or more powders are mixed in a container with a liquid selected from nitrogen or short-chain alcohols, where at least one of the powders has an angle of repose greater than approximately 50 degrees. The method is useful in preparing blended powders of Li halides and MgO for use in the preparation of thermal battery separators.

  5. Les séquelles de brûlures cervicocéphaliques chez l’enfant

    Science.gov (United States)

    Sankale, A.A.; Ndiaye, A.; Ndoye, A.; Ndiaye, L.; Ndoye, M.

    2011-01-01

    Summary La peau, barrière protectrice de l’organisme, est très exposée aux agressions et donc aux brûlures. Le but de ce travail est d’apprécier les particularités des séquelles de brûlure cervicofaciales chez l’enfant en milieu sub-saharien et d’évaluer leur prise en charge. Il s’agit d’une étude rétrospective réalisée dans le service de Chirurgie Pédiatrique du Centre Hospitalo-universitaire Aristide Le Dantec de Dakar (Sénégal). Vingt-sept dossiers de patients ont été colligés entre mai 2001 et avril 2008. L’âge moyen lors de la consultation était de 6,7 ans et le sex ratio m:f de 1,7:1. La topographie des séquelles se répartit ainsi: la face (66,7%), le cou (29,6%) et le cuir chevelu (11,1%). Concernant le type de séquelles, les brides prédominaient (33,3%), suivies des cicatrices chéloïdiennes ou hypertrophiques (25,9%), des ectropions de paupières (18,5%), des alopécies du cuir chevelu (11,1%), des ulcérations chroniques (7,4%) et de dyschromie (3,7%). Le traitement a été chirurgical dans 55,7% des cas: plasties en Z suivies ou non d’une greffe de peau pour les brides et libération de bride suivie d’une greffe pour les ectropions de paupières. Pour ce qui concerne les patients opérés, la morbidité opératoire a été de 20% et la mortalité opératoire nulle. Les cicatrices chéloïdiennes ont fait l’objet d’un traitement médical par infiltrations de dermocorticoïdes. Au-delà de l’urgence, les brûlures cervicofaciales de l’enfant entraînent un préjudice esthétique et fonctionnel important. L’amélioration de leur pronostic passe par la qualité des premiers soins et par la sensibilisation des parents aux risques d’accidents domestiques. PMID:21991239

  6. Polystyrene/Hyperbranched Polyester Blends and Reactive Polystyrene/Hyperbranched Polyester Blends

    National Research Council Canada - National Science Library

    Mulkern, Thomas

    1999-01-01

    .... In this work, the incorporation of HBPs in thermoplastic blends was investigated. Several volume fractions of hydroxyl functionalized hyperbranched polyesters were melt blended with nonreactive polystyrene (PS...

  7. Performance of Blended Learning in University Teaching:

    Directory of Open Access Journals (Sweden)

    Michael Reiss

    2010-07-01

    Full Text Available Blended learning as a combination of classroom teaching and e-learning has become a widely represented standard in employee and management development of companies. The exploratory survey “Blended Learning@University” conducted in 2008 investigated the integration of blended learning in higher education. The results of the survey show that the majority of participating academic teachers use blended learning in single courses, but not as a program of study and thus do not exploit the core performance potential of blended learning. According to the study, the main driver of blended learning performance is its embeddedness in higher education. Integrated blended programs of study deliver the best results. In blended learning, learning infrastructure (in terms of software, culture, skills, funding, content providing, etc. does not play the role of a performance driver but serves as an enabler for blended learning.

  8. Blending Words Found In Social Media

    Directory of Open Access Journals (Sweden)

    Giyatmi Giyatmi

    2017-12-01

    Full Text Available There are many new words from the social media such as Netizen, Trentop, and Delcon. Those words include in blending. Blending is one of word formations combining two clipped words to form a brand new word. The researchers are interested in analyzing blend words used in the social media such as Instagram, Twitter, Facebook, and Blackberry Messenger. This research aims at (1 finding blend words used in the social media (2 describing kinds of blend words used in social media (3 describing the process of blend word formation used in the social media. This research uses some theories dealing with definition of blending and kinds of blending. This research belongs to descriptive qualitative research. Data of the research are English blend words used in social media. Data sources of this research are websites consisting of some English words used in social media and some social media users as the informant. Techniques of data collecting in this research are observation and simak catat. Observation is by observing some websites consisting of some English words used in social media. Simak catat is done by taking some notes on the data and encoding in symbols such as No/Blend words/Kinds of Blending. The researchers use source triangulation to check the data from the researchers with the informant and theory triangulation to determine kinds of blending and blend word formation in social media. There are115 data of blend words. Those data consists of 65 data of Instagram, 47 data of Twitter, 1 datum of Facebook, and 2 data of Blackberry Messenger. There are 2 types of blending used in social media;108 data of blending with clipping and 7 data of blending with overlapping. There are 10 ways of blend word formation found in this research.

  9. Blended Learning: enabling Higher Education Reform

    Directory of Open Access Journals (Sweden)

    Kathleen Matheos

    2018-01-01

    Full Text Available Blended learning research and practice have been areas of growth for two decades in Canada, with over 95% of Canadian higher education institutions involved in some form of blended learning. Despite strong evidence based research and practice blended learning, for the most part, has remained at sidelined in Canadian universities. The article argues the need for blended learning to situate itself within the timely and crucial Higher Education Reform (HER agenda. By aligning the affordances of blended learning with the components of HER, blended learning can clearly serve as an enabler for HER.

  10. Blended Learning as Transformational Institutional Learning

    Science.gov (United States)

    VanDerLinden, Kim

    2014-01-01

    This chapter reviews institutional approaches to blended learning and the ways in which institutions support faculty in the intentional redesign of courses to produce optimal learning. The chapter positions blended learning as a strategic opportunity to engage in organizational learning.

  11. Morphology development in immiscible polymer blends

    NARCIS (Netherlands)

    Cardinaels, R.M.; Moldenaers, P.; Guo, Qipeng

    This chapter discusses the morphology development of immiscible binary polymer blends. It first describes morphology development in droplet-matrix structures, the dynamics of fibrillar structures and cocontinuous structures. The chapter then considers binary immiscible polymer blends, such systems

  12. Radiation effect on PVC/ENR blends

    International Nuclear Information System (INIS)

    Chantara Thevy Ratnam; Khairul Zaman Mohd Dahlan

    1997-01-01

    The effect of irradiation on the physical properties of Polyvinyl Chloride / Epoxidised Natural Rubber Blends (PVC/ENR blends) were investigated. The enhancement in tensile strength, elongation at break, hardness and aging properties of the blends have confirmed the positive effect of irradiation on the blends. It is evident from gel fraction and infra red spectroscopic studies that the blends of PVC and ENR cross-linked upon irradiation. The results also revealed that at any blend composition, the enhancement in properties depend on irradiation dose which controls the degree of radiation induced cross-linking. In an attempt to maximize the constructive effect of irradiation, the influence of various additives such as stabilizers, radiation sensitizers, fillers and processing aids on the blend properties were studied. The changes in blend properties upon irradiation with the presents of above additives were also presented in this paper

  13. NESDIS Blended Rain Rate (RR) Products

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The blended Rain Rate (RR) product is derived from multiple sensors/satellites. The blended products were merged from polar-orbiting and geostationary satellite...

  14. Intrinsically safe moisture blending system

    Science.gov (United States)

    Hallman Jr., Russell L.; Vanatta, Paul D.

    2012-09-11

    A system for providing an adjustable blend of fluids to an application process is disclosed. The system uses a source of a first fluid flowing through at least one tube that is permeable to a second fluid and that is disposed in a source of the second fluid to provide the adjustable blend. The temperature of the second fluid is not regulated, and at least one calibration curve is used to predict the volumetric mixture ratio of the second fluid with the first fluid from the permeable tube. The system typically includes a differential pressure valve and a backpressure control valve to set the flow rate through the system.

  15. Wavelet and Blend maps for texture synthesis

    OpenAIRE

    Du Jin-Lian; Wang Song; Meng Xianhai

    2011-01-01

    blending is now a popular technology for large realtime texture synthesis .Nevertheless, creating blend map during rendering is time and computation consuming work. In this paper, we exploited a method to create a kind of blend tile which can be tile together seamlessly. Note that blend map is in fact a kind of image, which is Markov Random Field, contains multiresolution signals, while wavelet is a powerful way to process multiresolution signals, we use wavelet to process the traditional ble...

  16. Blended Identities: Identity Work, Equity and Marginalization in Blended Learning

    Science.gov (United States)

    Heikoop, Will

    2013-01-01

    This article is a theoretical study of the self-presentation strategies employed by higher education students online; it examines student identity work via profile information and avatars in a blended learning environment delivered through social networking sites and virtual worlds. It argues that students are faced with difficult choices when…

  17. 40 CFR 80.82 - Butane blending.

    Science.gov (United States)

    2010-07-01

    ... FUELS AND FUEL ADDITIVES Reformulated Gasoline § 80.82 Butane blending. A refiner for any refinery that produces gasoline by blending butane with conventional gasoline or reformulated gasoline or RBOB may meet... paragraph (b)(1) of this section, the refiner may: (i) Blend the butane with conventional gasoline, or...

  18. 7 CFR 989.16 - Blend.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Blend. 989.16 Section 989.16 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... CALIFORNIA Order Regulating Handling Definitions § 989.16 Blend. Blend means to mix or commingle raisins. ...

  19. Netbaserede uddannelser og blended learning

    DEFF Research Database (Denmark)

    Bertelsen, Jesper Vedel; Vognsgaard Hjernø, Henriette; Jensen, Michael Peter

    2016-01-01

    Denne håndbog er tænkt som inspiration til uddannelsesfaglige medarbejdere, som er eller skal i gang med at undervise på en netbaseret uddannelse i UCL. Håndbogen giver et teoretisk overblik i forhold til netbaserede uddannelser, online- og blended learning samt en indførsel i hvilke didaktiske...

  20. New Faces of Blended Learning

    Science.gov (United States)

    Horn, Michael B.; Fisher, Julia Freeland

    2017-01-01

    The Clayton Christiansen Institute maintains a database of more than 400 schools across the United States that have implemented some form of blended learning, which combines online learning with brick-and-mortar classrooms. Data the Institute has collected over the past six months suggests three trends as this model continues to evolve and mature.…

  1. Multiscattering illumination in blended acquisition

    NARCIS (Netherlands)

    Berkhout, A.J.; Blacquiere, G.; Verschuur, D.J.

    2012-01-01

    In traditional seismic surveys, the firing time between shots is such that the shot records do not interfere in time. However, in the concept of blended acquisition, the records do overlap, allowing denser source sampling and wider azimuths in an economic way. A denser shot sampling and wider

  2. Radiation crosslinking of polymer blends

    International Nuclear Information System (INIS)

    Spenadel, L.

    1979-01-01

    Rocked by the one-two punch of rising energy costs and tougher pollution controls, a growing number of companies are looking to radiation crosslinking as a cheaper, cleaner alternative to heat and costly chemical crosslinking agents such as peroxides. With the development of larger, more powerful electron beam machines it is now possible to irradiate parts as thick as 400 mils in a single pass. Two application areas which have been investigated at our laboratory are the electron beam processing of thermoplastic elastomeric automotive parts and EPDM electrical insulation. This paper covers work carried out to develop the necessary technology base for the radiation crosslinking of ethylene propylene/polyolefin blends. Initial results indicate that EP/PE blends of electrical insulation quality cross-link quite readily when irradiated. On the other hand, EP/PP blends developed for automotive fascia require the addition of crosslinking monomers such as trimethylol propane trimethacrylate in order for crosslinking to predominate over chain scission. Crosslinking EP/PP blends improve mar resistance, flexural set and deformation at elevated temperatures. These are all key properties for automotive fascia. (author)

  3. Confined flow of polymer blends

    NARCIS (Netherlands)

    Tufano, C.; Peters, G.W.M.; Meijer, H.E.H.

    2008-01-01

    The influence of confinement on the steady-state morphology of two different emulsions is investigated. The blends, made from polybutene (PB) in polydimethylsiloxane (PDMS) and polybutadiene (PBD) in PDMS, are sheared between two parallel plates, mostly with a standard gap spacing of 40 m, in the

  4. PEO + PVP blended polymer composite

    Indian Academy of Sciences (India)

    Blended polymer films of polyethylene oxide + polyvinyl pyrrolidone (PEO + PVP) containing transition metal (TM) ions like Fe3+, Co2+ and Ni2+ have been synthesized by a solution casting method. For these films, structural, thermal, magnetic and optical properties have been studied. X-ray diffraction results reveal the ...

  5. Blended Learning: The Student Viewpoint

    African Journals Online (AJOL)

    Student perceptions were assessed using Mann–Whitney. U‑test and ... Keywords: Blended learning, Online learning, Students' perceptions. Access this article online ..... performance, EC: Educational counseling, MIB: Medical insurance billing, MT: .... distance in education at the harvard business school. Educ. Technol ...

  6. Improvement of biodiesel methanol blends

    Directory of Open Access Journals (Sweden)

    Y. Datta Bharadwaz

    2016-06-01

    Full Text Available The main objective of this work was to improve the performance of biodiesel–methanol blends in a VCR engine by using optimized engine parameters. For optimization of the engine, operational parameters such as compression ratio, fuel blend, and load are taken as factors, whereas performance parameters such as brake thermal efficiency (Bth and brake specific fuel consumption (Bsfc and emission parameters such as carbon monoxide (CO, unburnt hydrocarbons (HC, Nitric oxides (NOx and smoke are taken as responses. Experimentation is carried out as per the design of experiments of the response surface methodology. Optimization of engine operational parameters is carried out using Derringers Desirability approach. From the results obtained it is inferred that the VCR engine has maximum performance and minimum emissions at 18 compression ratio, 5% fuel blend and at 9.03 kg of load. At this optimized operating conditions of the engine the responses such as brake thermal efficiency, brake specific fuel consumption, carbon monoxide, unburnt hydrocarbons, nitric oxide, and smoke are found to be 31.95%, 0.37 kg/kW h, 0.036%, 5 ppm, 531.23 ppm and 15.35% respectively. It is finally observed from the mathematical models and experimental data that biodiesel methanol blends have maximum efficiency and minimum emissions at optimized engine parameters.

  7. Introducing blended e-learning course design

    DEFF Research Database (Denmark)

    Gyamfi, Samuel Adu; Ryberg, Thomas

    2012-01-01

    In the face of diminishing education budgets in higher education, blended learning has been found to be a viable and effective approach to deliver high-quality, up-to-date, on-demand solutions to developing cross-curricular skills of undergraduates. However, research has also shown that blended...... learning solutions do not often live up to the potential of the approach or fail to produce the intended results because the students are not always equipped to handle the technical, psychological and organisational challenges of blended learning approaches. This project surveyed seventy-five first year...... the students’ e-readiness for an implementation of a blend-ed course design....

  8. Attraction of Pollinators to Atemoya (Annona squamosa × Annona cherimola) in Puerto Rico Using Commercial Lures and Food Attractants.

    Science.gov (United States)

    Jenkins, David A; Millan-Hernandez, Christian; Cline, Andrew R; McElrath, Thomas C; Irish, Brian; Goenaga, Ricardo

    2015-08-01

    Atemoya is a hybrid between Annona squamosa L. and Annona cherimola Miller (Annonaceae) and has potential to be an important fruit crop in tropical and subtropical areas. A major impediment to fruit production is low fruit set due to inadequate pollinator visits, typically, by beetles in the family Nitidulidae. We used Universal moth traps to monitor the attractiveness of two commercially available Nitidulidae lures in combination with various food attractants, including raw bread dough, apple juice, and malta beverage, a soft drink by-product of the brewing process. The most commonly trapped beetles were, in order of decreasing frequency, Carpophilus dimidiatus (F.), Brachypeplus mutilatus Erichson, Urophorus humeralis (F.) (Coleoptera: Nitidulidae), and Europs fervidus Blatchley (Coleoptera: Monotomidae). All traps, except the unbaited control traps, caught beetles. In a previous study, we found that combining two commercial lures had a synergistic effect on the attraction of these beetle species. In this study, the addition of food attractants increased the number of beetles trapped compared with traps baited with only the commercial lures. Also, food attractants appear to be key in attracting U. humeralis; only one U. humeralis individual of the 206 caught during the experiment was trapped without a food attractant. The variation between the number of beetles caught in traps containing the same treatments was high and may explain the erratic results reported in other studies of pollination in Annona spp. The results are discussed with respect to the use of nitidulid lures and food attractants to increase fruit set in atemoya and other Annonaceae. Published by Oxford University Press on behalf of Entomological Society of America 2015. This work is written by US Government employees and is in the public domain in the US.

  9. Improving detection tools for emerald ash borer (Coleoptera: Buprestidae): comparison of multifunnel traps, prism traps, and lure types at varying population densities.

    Science.gov (United States)

    Crook, Damon J; Francese, Joseph A; Rietz, Michael L; Lance, David R; Hull-Sanders, Helen M; Mastro, Victor C; Silk, Peter J; Ryall, Krista L

    2014-08-01

    The emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), is a serious invasive pest of North American ash (Fraxinus spp.) that has caused devastating mortality since it was first identified in North America in 2002. In 2012, we conducted field trapping assays that tested the efficacy of purple prism and fluon-coated green multifunnel (Lindgren funnel) traps. Traps were baited with combinations of several lures that were previously shown to be attractive to A. planipennis: manuka oil--a sesquiterpene-rich oil, (3Z)-hexenol--a green leaf volatile, or (3Z)-dodecen-12-olide [= (3Z)-lactone], a sex pheromone. Eighty-nine blocks (trap lines) were tested throughout nine states along the outer edges of the currently known A. planipennis infestation in North America. Trap catch was highest on fluon-coated green multifunnel traps, and trap detections at sites with low A. planipennis population density ranged from 72 to 76% for all trap and lure types tested. (3Z)-hexenol and (3Z)-lactone baited traps functioned as well as (3Z)-hexenol and manuka oil-baited traps. Independent of the lure used, detection rates on green fluon-coated multifunnel traps were comparable with glued purple prism traps in areas with low A. planipennis population densities.

  10. Data blending in health care : Evaluation of data blending

    OpenAIRE

    Chen, Qian

    2016-01-01

    This report is aimed at those who are interested in data analysis and data blending. Decision making is crucial for an organization to succeed in today’s market. Data analysis is an important support activity in decision making and is applied in many industries, for example healthcare. For many years data analysts have worked on structured data in small volumes, with traditional methods such as spreadsheet. As new data sources emerged, such as social media, data is generated in higher volume,...

  11. X-ray blending device

    International Nuclear Information System (INIS)

    Manolov, S.S.; Donchev, I.D.; Paunchev, A.N.; Atanasov, A.B.; Kerin, T.P.

    1985-01-01

    The X-ray blending device comprises electric motors for vertical and horizontal blending plates, electrically connected with the output of the block for format voltages and mechanically connected with the measuring potentiometers' slides. The potentiometers are respectively connected with the data inputs of the block for format voltages, the control input of which is connected with the control block output in a mode of scanning. The data outputs of the format voltage block are connected through a buffer converter, a memory block and a decoder with the data inputs of the first and second digital-to-analog converters, the outputs of which are connected with the first inputs of the first and the second comparison circuits. The second inputs of the last are linked to the slides of the first and the second potentiometers and their inputs are connected with the data inputs of the first and the second combinational logic circuits. The output of the control block in a mode of scanning is connected with the first control inputs of the first and the second combinational logic circuits and with the control inputs of the memory block and the decoder. The second and the third control units of the first and the second combinational circuits are respectively linked with the outputs for a position determination of the vertical and horizontal blending plates from the control block in a mode of scanning. The outputs of the first and the second combinational logic circuits are respectively connected with the first and the second control bridge circuits, the control outputs of which are electrically connected with the first and the second electric motors for vertical and horizontal blending plates. 1 cl., 3 figs

  12. Épidémiologie des brûlures de la main chez les enfants vus dans le Centre National des Brûlés et de Chirurgie Plastique de Casablanca, Maroc

    Science.gov (United States)

    Rafik, A.; Lahlou, M.; Diouri, M.; Bahechar, N.; Chlihi, A.

    2015-01-01

    Summary Les brûlures de la main chez l’enfant constituent une source de séquelles invalidantes. A cet régard, la conservation et la restauration complète de la fonction de la main demeurent le but primordial de la prise en charge. Afin de répertorier les caractéristiques épidémiologiques, cliniques et évolutives des mains brûlées, nous avons réalisé une étude rétrospective étalée sur 4 ans, de janvier 2011 à janvier 2015. Cette étude a permis de colliger les cas de 313 enfants atteints de brûlure de la main vus dans le Centre National des Brulés et de Chirurgie Plastique du CHU Ibn Rochd de Casablanca. La majorité des brûlures touche les enfants de 3 à 6 ans (70% des cas), avec une légère prédominance masculine. La principale cause des brûlures survenant à cet âge est l’ébouillantement. Les brûlures par flamme représentent 33% des cas, celles par électricité 4,5%. Les brûlures chimiques et par contact sont anecdotiques (1 cas chacune). L’accident survient le plus souvent à domicile. Soixante douze pour cent des brûlures ont guéri spontanément. Afin de diminuer l’incidence de ces accidents, une approche préventive faite de sensibilisation et d’éducation devrait faire partie du cursus scolaire. PMID:27777543

  13. Blending of phased array data

    Science.gov (United States)

    Duijster, Arno; van Groenestijn, Gert-Jan; van Neer, Paul; Blacquière, Gerrit; Volker, Arno

    2018-04-01

    The use of phased arrays is growing in the non-destructive testing industry and the trend is towards large 2D arrays, but due to limitations, it is currently not possible to record the signals from all elements, resulting in aliased data. In the past, we have presented a data interpolation scheme `beyond spatial aliasing' to overcome this aliasing. In this paper, we present a different approach: blending and deblending of data. On the hardware side, groups of receivers are blended (grouped) in only a few transmit/recording channels. This allows for transmission and recording with all elements, in a shorter acquisition time and with less channels. On the data processing side, this blended data is deblended (separated) by transforming it to a different domain and applying an iterative filtering and thresholding. Two different filtering methods are compared: f-k filtering and wavefield extrapolation filtering. The deblending and filtering methods are demonstrated on simulated experimental data. The wavefield extrapolation filtering proves to outperform f-k filtering. The wavefield extrapolation method can deal with groups of up to 24 receivers, in a phased array of 48 × 48 elements.

  14. Teaching Shakespeare through blended learning

    Directory of Open Access Journals (Sweden)

    Lesley Hawkes

    2018-03-01

    Full Text Available This paper describes and discusses experimentation with the use of blended learning in teaching Shakespeare. Previous iterations of the subject in a traditional lecture and tutorial format had seen a decline in student attendance and a fall in student achievement at the higher grade levels. A further complicating issue was the range of expectations from the cohort, which comprised students from Creative Writing, Drama, and Education, a factor which also highlights the cross-disciplinary nature of teaching Shakespeare. A blended learning and lectorial format was employed to facilitate small group discussion of the plays in conjunction with a wider social and historical overview. Student feedback indicated that the changes to the delivery method were received positively, although some questions do remain concerning levels of student engagement and the specific disciplinary needs of student cohorts. The findings of the teaching of this subject will translate usefully to other fields and disciplines, especially as more and more subjects take up blended learning. The findings indicate that it is not enough to take up new technologies in the teaching of a unit. The learning environment must also be rethought and reconceptualised.

  15. Game innovation through conceptual blending

    DEFF Research Database (Denmark)

    Möring, Sebastian Martin

    In  this  paper  I  wish  to  apply implications of  the  Conceptual  Blending  Theory  to  computer  games.  I  will  analyze  chosen  examples  and  discuss  them  as  a  result  of  video  game  innovation  made  possible  through  "conceptual  blending."  Conceptual  blending  links  at  least.......,  Hell.  The  purpose  of  my  approach  is  not  so  much  to  validate  the  ideas  of  conceptual  blending  theory  through  another  field  of  examples  (computer  games)  but  to  name  and analyze characteristics of the mentioned games with the  help of a given method.......  integration  network  consisting  of  at  least  two  input  spaces,  a  generic  space  and  a  blended  space  as  well  as  its  governing  principles  consisting  of  composition,  completion,  and  elaboration.  With  the  help  of  these  instruments  I  analyze computer  games like  Tuper  Tario  Tros...

  16. BLENDED LEARNING STRATEGY IN TEACHER TRAINING PROGRAMS

    Directory of Open Access Journals (Sweden)

    Marian F. Byrka

    2017-12-01

    Full Text Available The article examines the implementation of blended learning strategy in teacher training programs as an innovation in online learning. The blended learning idea comes from blending elements which use online technology with more traditional face-to-face teaching in the same course. The article analyses teacher training programs offered by Chernivtsi Regional Institute of Postgraduate Pedagogical Education. Additional data were gathered through a questionnaire administered to teachers who attended training courses. The characteristics of blended learning strategy, its benefits and limitations for teacher training are supported by a review of literature. The article closes with the comparison of curriculum components (content delivery, learner activities, materials, and required competences between traditional and blended learning teacher training programs. Having obvious benefits in teacher training programs, the implementation of blended learning strategy sets some additional requirements to a learner, as well as to course instructors and lectors.

  17. Correspondence Theory and Phonological Blending in French

    Directory of Open Access Journals (Sweden)

    Lee Scott

    2014-07-01

    Full Text Available Though less productive than rival word-formation processes like compounding and affixation, blending is still a rich source of neologisms in French. Despite this productivity, however, blends are often seen by scholars as unpredictable, uninteresting, or both. This analysis picks up where recent studies of blending have left off, using Correspondence Theory and a bundle of segmental constraints to deal with this phenomenon as it pertains to French. More specifically, it shows that blending is the result of a single output standing in correspondence with two or more other outputs, and that we do not need to refer to prosodic information, which is crucial in accounts of blending in languages with lexical stress like English, to account for the process in French. The analysis also differs from previous studies in that it locates blending exclusively within the phonology, leaving its morphological and semantic characteristics to be handled by other processes in the grammar.

  18. Evaporation characteristics of ETBE-blended gasoline

    International Nuclear Information System (INIS)

    Okamoto, Katsuhiro; Hiramatsu, Muneyuki; Hino, Tomonori; Otake, Takuma; Okamoto, Takashi; Miyamoto, Hiroki; Honma, Masakatsu; Watanabe, Norimichi

    2015-01-01

    Highlights: • We chose 8-component hydrocarbon mixture as a model gasoline, and defined the molar mass of gasoline. • We proposed an evaporation model assuming a 2-component mixture of gasoline and ETBE. • We predicted the change in the vapor pressure of ETBE-blended gasoline by evaporation. • The vapor pressures were measured and compared as a means of verifying the model. • We presented the method for predicting flash points of the ETBE-blended gasoline. - Abstract: To reduce greenhouse gas emissions, which contribute to global warming, production of gasoline blended with ethyl tert-buthyl ether (ETBE) is increasing annually. The flash point of ETBE is higher than that of gasoline, and blending ETBE into gasoline will change the flash point and the vapor pressure. Therefore, it is expected that the fire hazard caused by ETBE-blended gasoline would differ from that caused by normal gasoline. The aim of this study was to acquire the knowledge required for estimating the fire hazard of ETBE-blended gasoline. Supposing that ETBE-blended gasoline was a two-component mixture of gasoline and ETBE, we developed a prediction model that describes the vapor pressure and flash point of ETBE-blended gasoline in an arbitrary ETBE blending ratio. We chose 8-component hydrocarbon mixture as a model gasoline, and defined the relation between molar mass of gasoline and mass loss fraction. We measured the changes in the vapor pressure and flash point of gasoline by blending ETBE and evaporation, and compared the predicted values with the measured values in order to verify the prediction model. The calculated values of vapor pressures and flash points corresponded well to the measured values. Thus, we confirmed that the change in the evaporation characteristics of ETBE-blended gasoline by evaporation could be predicted by the proposed model. Furthermore, the vapor pressure constants of ETBE-blended gasoline were obtained by the model, and then the distillation curves were

  19. Evaporation characteristics of ETBE-blended gasoline

    Energy Technology Data Exchange (ETDEWEB)

    Okamoto, Katsuhiro, E-mail: okamoto@nrips.go.jp [National Research Institute of Police Science, 6-3-1 Kashiwanoha, Kashiwa, Chiba 277-0882 (Japan); Hiramatsu, Muneyuki [Yamanashi Prefectural Police H.Q., 312-4 Kubonakajima, Isawa-cho, Usui, Yamanashi 406-0036 (Japan); Hino, Tomonori; Otake, Takuma [Metropolitan Police Department, 2-1-1 Kasumigaseki, Chiyoda-ku, Tokyo 100-8929 (Japan); Okamoto, Takashi; Miyamoto, Hiroki; Honma, Masakatsu; Watanabe, Norimichi [National Research Institute of Police Science, 6-3-1 Kashiwanoha, Kashiwa, Chiba 277-0882 (Japan)

    2015-04-28

    Highlights: • We chose 8-component hydrocarbon mixture as a model gasoline, and defined the molar mass of gasoline. • We proposed an evaporation model assuming a 2-component mixture of gasoline and ETBE. • We predicted the change in the vapor pressure of ETBE-blended gasoline by evaporation. • The vapor pressures were measured and compared as a means of verifying the model. • We presented the method for predicting flash points of the ETBE-blended gasoline. - Abstract: To reduce greenhouse gas emissions, which contribute to global warming, production of gasoline blended with ethyl tert-buthyl ether (ETBE) is increasing annually. The flash point of ETBE is higher than that of gasoline, and blending ETBE into gasoline will change the flash point and the vapor pressure. Therefore, it is expected that the fire hazard caused by ETBE-blended gasoline would differ from that caused by normal gasoline. The aim of this study was to acquire the knowledge required for estimating the fire hazard of ETBE-blended gasoline. Supposing that ETBE-blended gasoline was a two-component mixture of gasoline and ETBE, we developed a prediction model that describes the vapor pressure and flash point of ETBE-blended gasoline in an arbitrary ETBE blending ratio. We chose 8-component hydrocarbon mixture as a model gasoline, and defined the relation between molar mass of gasoline and mass loss fraction. We measured the changes in the vapor pressure and flash point of gasoline by blending ETBE and evaporation, and compared the predicted values with the measured values in order to verify the prediction model. The calculated values of vapor pressures and flash points corresponded well to the measured values. Thus, we confirmed that the change in the evaporation characteristics of ETBE-blended gasoline by evaporation could be predicted by the proposed model. Furthermore, the vapor pressure constants of ETBE-blended gasoline were obtained by the model, and then the distillation curves were

  20. Mechanical properties of irradiated rubber-blends

    International Nuclear Information System (INIS)

    Nasr, G.M.; Madani, M.

    2005-01-01

    A study has been made on blend ratios of natural rubber (NR) and acrylonitrile butadiene rubber (NBR) that are loaded with general purpose furnace (GPE) carbon black and irradiated at different gamma radiation doses. It was fount that the mechanical properties of such blend are highly affected by γ- irradiation dose and the composition ratios of its constituents. The elongation at break for blends was found to increase slightly with increasing NBR loafing which is mainly due to the stiffness of blending matrix formation between NR and GPF carbon black particles. The hysteresis loss, extension ratio and shape factor have been calculated for the different un-irradiated and irradiated samples

  1. THE COMBUSTION CHARACTERISTICS OF LIGNITE BLENDS

    Institute of Scientific and Technical Information of China (English)

    Cheng Jun; Zhou Junhu; Cao Xinyu; Cen Kefa

    2000-01-01

    The combustion characteristics of lignite blends were studied with a thermogravimetric analyzer (t.g.a.), at constant heating rate.The characteristic temperatures were determined from the burning profiles.It was found that the characteristic times of combustion reaction moved forward, the ignition temperature dropped and the burnout efficiency slightly changed when blending lignites.The characteristic parameters of blends could not be predicted as a linear function of the average values of the individual lignites.when blending with less reactive coal, the ignition and burnout characteristics of lignite turned worse.

  2. Design Principles for the Blend in Blended Learning: A Collective Case Study

    Science.gov (United States)

    Lai, Ming; Lam, Kwok Man; Lim, Cher Ping

    2016-01-01

    This paper reports on a collective case study of three blended courses taught by different instructors in a higher education institution, with the purpose of identifying the different types of blend and how the blend supports student learning. Based on the instructors' and students' interviews, and document analysis of course outlines, two major…

  3. Sludge Stabilization Campaign blend plan

    International Nuclear Information System (INIS)

    De Vries, M.L.

    1994-01-01

    This sludge stabilization blend plan documents the material to be processed and the order of processing for the FY95 Sludge Stabilization Campaign. The primary mission of this process is to reduce the inventory of unstable plutonium bearing sludge. The source of the sludge is residual and glovebox floor sweepings from the production of material at the Plutonium Finishing Plant (PFP). The reactive sludge is currently being stored in various gloveboxes at PFP. There are two types of the plutonium bearing material that will be thermally stabilized in the muffle furnace: Plutonium Reclamation Facility (PRF) sludge and Remote Mechanical C (RMC) Line material

  4. Les séquelles de brûlures cervicales: aspects épidémiologique, clinique et thérapeutique au Maroc

    Science.gov (United States)

    Rafik, Amine; Chabak, Hakim; Diouri, Mounia; Bahechar, Naïma; Chlihi, Abdessamad

    2015-01-01

    Les séquelles de brûlures cervicales représentent une entité fréquente des séquelles de brûlure, elles affectent la fonction, l'esthétique et l’état psychologique des patients et peuvent être de traitement difficile. Il s'agit d'une étude rétrospective étalée sur 5 ans de Mars 2009 au Octobre2014, réalisée au centre national des brûlés et de chirurgie plastique au CHU Ibn Rochd Casablanca. Nous avons analysé les caractéristiques épidémiologiqueset cliniques ainsi que les indications et les résultats thérapeutiques chez 300 patients présentant des rétractions cervicales post-brûlure, suivis dans notre formation. Les jeunes femmes étaient le plus souvent touchées (56%). la brûlure thermique par flamme de butane dans le cadre d'accident domestique était l’étiologie la plus fréquente (91%).75% des patients ont été pris en charge dans un délai de 18 mois après avoir présenté une incapacité fonctionnelle. Les brides cervicales modérées et sévères sont les plus fréquentes et représentent respectivement 60% et 16% des cas. Le traitement chirurgical a fait appel aux greffes cutanées dans 67%des cas, aux plasties locales dans 24%des cas et aux lambeaux dans 24% des cas, les résultats sont jugés bons dans 75%des cas et moyens dans 18% des cas, tandis que les cas restants (7%) ont nécessité une reprise chirurgicale. Le traitement des brides cervicales doit être associé à un programme de rééducation adapté, afin d'assurer la pérennité des résultats fonctionnels et esthétiques. PMID:26301017

  5. Linear polarizers based on oriented polymer blends

    NARCIS (Netherlands)

    Jagt, H.J.B.; Dirix, Y.J.L.; Hikmet, R.A.M.; Bastiaansen, C.W.M.

    1998-01-01

    Linear sheet polarizers based on the anisotropic scattering of light by drawn polymer blends are introduced here. The proper selection of materials and processing conditions for the production of large-area, flexible films of phase-segregated polymer blends suitable for polarization applications are

  6. Enhancing Students' Language Skills through Blended Learning

    Science.gov (United States)

    Banditvilai, Choosri

    2016-01-01

    This paper presents a case study of using blended learning to enhance students' language skills and learner autonomy in an Asian university environment. Blended learning represents an educational environment for much of the world where computers and the Internet are readily available. It combines self-study with valuable face-to-face interaction…

  7. Blended Learning in Personalized Assistive Learning Environments

    Science.gov (United States)

    Marinagi, Catherine; Skourlas, Christos

    2013-01-01

    In this paper, the special needs/requirements of disabled students and cost-benefits for applying blended learning in Personalized Educational Learning Environments (PELE) in Higher Education are studied. The authors describe how blended learning can form an attractive and helpful framework for assisting Deaf and Hard-of-Hearing (D-HH) students to…

  8. Improving Curriculum through Blended Learning Pedagogy

    Science.gov (United States)

    Darojat, Ojat

    2016-01-01

    This paper is a study of blended learning pedagogy in open and distance learning (ODL), involving two universities in Southeast Asia, STOU Thailand and UT Indonesia. The purpose of this study is to understand the issues related to the implementation of blended-learning pedagogy. Qualitative case study was employed to optimize my understanding of…

  9. Preparing Teachers for Emerging Blended Learning Environments

    Science.gov (United States)

    Oliver, Kevin M.; Stallings, Dallas T.

    2014-01-01

    Blended learning environments that merge learning strategies, resources, and modes have been implemented in higher education settings for nearly two decades, and research has identified many positive effects. More recently, K-12 traditional and charter schools have begun to experiment with blended learning, but to date, research on the effects of…

  10. Effect of noise in blending and deblending

    NARCIS (Netherlands)

    Berkhout, A.J.; Blacquière, G.

    2013-01-01

    If simultaneous shooting is carried out by incoherent source arrays, being the condition of blended acquisition, the deblending process generates shot records with a very low residual interference (blending noise). We found, theoretically and numerically, that deblended shot records had a better

  11. PAIRWISE BLENDING OF HIGH LEVEL WASTE

    International Nuclear Information System (INIS)

    CERTA, P.J.

    2006-01-01

    The primary objective of this study is to demonstrate a mission scenario that uses pairwise and incidental blending of high level waste (HLW) to reduce the total mass of HLW glass. Secondary objectives include understanding how recent refinements to the tank waste inventory and solubility assumptions affect the mass of HLW glass and how logistical constraints may affect the efficacy of HLW blending

  12. Multiscattering illumination in blended acquisition design

    NARCIS (Netherlands)

    Berkhout, A.J.; Blacquière, G.; Verschuur, D.J.

    2010-01-01

    In traditional seismic surveys the firing time between shots is such that the records do not interfere in time. However, in the concept of blending the records do overlap, allowing much denser and wider geometries in an economic way. The blending parameters are the locations of the involved sources

  13. Structuring of Interface-Modified Polymer Blends

    DEFF Research Database (Denmark)

    Lyngaae-Jørgensen, Jørgen

    1999-01-01

    The paper treats the case where blends of polystyrene (PS), poly (dimethylsiloxane) (PDMS) and a diblock copolymer of PS and PDMS are used as model materials. This modelsystem is predicted to be "stable" in discrete blends in simple shear flow. Stable in the sence that the block copolymer can not...

  14. Meeting Diverse Learner Needs with Blended Learning

    Science.gov (United States)

    Owen, Hazel

    2010-01-01

    This article describes a 40-week Computer, Research Skills, and Projects (CRSP) blended learning course designed and implemented at Dubai Men's College. The learning employed a design using socio-constructivist principles in the blended approach to cater to the learning preferences of students. (Contains 2 figures and 1 footnote.)

  15. A blending rule for octane numbers of PRFs and TPRFs with ethanol

    KAUST Repository

    AlRamadan, Abdullah S.; Sarathy, Mani; Khurshid, Muneeb; Badra, Jihad

    2016-01-01

    -gasoline synergistic/antagonistic blending effects. Understanding ethanol blending effects with simpler gasoline surrogates blends may enable a better understanding of ethanol blending with complex multi-component gasoline fuels. This study presents a blending rule

  16. Development of high-performance blended cements

    Science.gov (United States)

    Wu, Zichao

    2000-10-01

    This thesis presents the development of high-performance blended cements from industrial by-products. To overcome the low-early strength of blended cements, several chemicals were studied as the activators for cement hydration. Sodium sulfate was discovered as the best activator. The blending proportions were optimized by Taguchi experimental design. The optimized blended cements containing up to 80% fly ash performed better than Type I cement in strength development and durability. Maintaining a constant cement content, concrete produced from the optimized blended cements had equal or higher strength and higher durability than that produced from Type I cement alone. The key for the activation mechanism was the reaction between added SO4 2- and Ca2+ dissolved from cement hydration products.

  17. Evaporation characteristics of ETBE-blended gasoline.

    Science.gov (United States)

    Okamoto, Katsuhiro; Hiramatsu, Muneyuki; Hino, Tomonori; Otake, Takuma; Okamoto, Takashi; Miyamoto, Hiroki; Honma, Masakatsu; Watanabe, Norimichi

    2015-04-28

    To reduce greenhouse gas emissions, which contribute to global warming, production of gasoline blended with ethyl tert-buthyl ether (ETBE) is increasing annually. The flash point of ETBE is higher than that of gasoline, and blending ETBE into gasoline will change the flash point and the vapor pressure. Therefore, it is expected that the fire hazard caused by ETBE-blended gasoline would differ from that caused by normal gasoline. The aim of this study was to acquire the knowledge required for estimating the fire hazard of ETBE-blended gasoline. Supposing that ETBE-blended gasoline was a two-component mixture of gasoline and ETBE, we developed a prediction model that describes the vapor pressure and flash point of ETBE-blended gasoline in an arbitrary ETBE blending ratio. We chose 8-component hydrocarbon mixture as a model gasoline, and defined the relation between molar mass of gasoline and mass loss fraction. We measured the changes in the vapor pressure and flash point of gasoline by blending ETBE and evaporation, and compared the predicted values with the measured values in order to verify the prediction model. The calculated values of vapor pressures and flash points corresponded well to the measured values. Thus, we confirmed that the change in the evaporation characteristics of ETBE-blended gasoline by evaporation could be predicted by the proposed model. Furthermore, the vapor pressure constants of ETBE-blended gasoline were obtained by the model, and then the distillation curves were developed. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. Quercivorol as a lure for the polyphagous and Kuroshio shot hole borers, Euwallacea spp. nr. fornicatus (Coleoptera: Scolytinae, vectors of Fusarium dieback

    Directory of Open Access Journals (Sweden)

    Christine Dodge

    2017-08-01

    Full Text Available The polyphagous shot hole borer and Kuroshio shot hole borer, two members of the Euwallacea fornicatus species complex (Coleoptera: Curculionidae: Scolytinae, are invasive ambrosia beetles that harbor distinct species of Fusarium fungal symbionts. Together with the damage caused by gallery construction, these two phytopathogenic Fusarium species are responsible for the emerging tree disease Fusarium dieback, which affects over 50 common tree species in Southern California. Host trees suffer branch dieback as the xylem is blocked by invading beetles and fungi, forcing the costly removal of dead and dying trees in urban areas. The beetles are also threatening natural riparian habitats, and avocado is susceptible to Fusarium dieback as well, resulting in damage to the avocado industries in California and Israel. Currently there are no adequate control mechanisms for shot hole borers. This paper summarizes efforts to find a suitable lure to monitor shot hole borer invasions and dispersal. Field trials were conducted in two counties in Southern California over a span of two years. We find that the chemical quercivorol is highly attractive to these beetles, and perform subsequent field experiments attempting to optimize this lure. We also explore other methods of increasing trap catch and effects of other potential attractants, as well as the deterrents verbenone and piperitone.

  19. Blending formal and informal learning

    DEFF Research Database (Denmark)

    Frølund, Gro

    The aim of this paper is to explore the possibilities collaboration offers in the virtual learning environments of the armed forces. I will argue that for reasons of culture and structure in the armed forces, the opportunities created by collaborative learning activities in e-learning and blended...... learning are especially fruitful here. Collaboration is a pervasive, foundational form of activity in our armies, air forces and navies. It expresses itself in cultural traits such as never leaving a soldier behind, taking your share and being someone you can count on, to name a few. Moreover, most armed...... forces activities are structured forms of collaboration; staff work, tactical planning, active duty and so forth are all day-to-day examples. Collaborative activities in virtual learning spaces tap into that culture. However, and perhaps confusingly, a study I conducted last year at the Royal Danish...

  20. Ash Stabilization Campaign Blend Plan

    International Nuclear Information System (INIS)

    Winstead, M.L.

    1995-01-01

    This Stabilization Blend Plan documents the material to be processed and the processing order for the FY95 Ash Stabilization Campaign. The primary mission of this process is to reduce the inventory of unstable plutonium bearing ash. The source of the ash is from Rocky Flats and the 232-Z incinerator at the Plutonium Finishing Plant (PFP). The ash is currently being stored in Room 235B and Vault 174 in building 234-5Z. The sludge is to be thermally stabilized in a glovebox in room 230A of the 234-5Z building and material handling for the process will be done in room 230B of the same building. The campaign is scheduled for approximately 12--16 weeks. A total of roughly 4 kg of Pu will be processed

  1. Blending traditional and digital marketing

    Directory of Open Access Journals (Sweden)

    Raluca Dania TODOR

    2016-07-01

    Full Text Available It is a matter of fact that we are in the digital era and internet marketing and social media have a significant impact on the way consumers behave, companies do business and it is a must for companies to adapt to the new reality. Due to the fast evolution of the technology, the continuous increase in demand and supply, the supply chain elongation and the big amount of date, the only solution to face the major changes is the automation of all the processes. But even though the new era of communication is here, specialist suggest that companies should not ignore traditional methods, and to try to blend digital marketing with traditional campaigns in order to achieve their goals.

  2. Blended Learning in Action: A Practical Guide toward Sustainable Change

    Science.gov (United States)

    Tucker, Catlin R.; Wycoff, Tiffany; Green, Jason T.

    2017-01-01

    Blended learning has the power to reinvent education, but transitioning to a blended model is challenging. Blended learning requires a fundamentally new approach to learning as well as a new skillset for both teachers and school leaders. Loaded with research, examples, and resources, "Blended Learning in Action" demonstrates the…

  3. 27 CFR 24.213 - Heavy bodied blending wine.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Heavy bodied blending wine..., DEPARTMENT OF THE TREASURY LIQUORS WINE Production of Other Than Standard Wine § 24.213 Heavy bodied blending wine. Heavy bodied blending wine is wine made for blending purposes from grapes or other fruit without...

  4. BioBlend.objects: metacomputing with Galaxy.

    Science.gov (United States)

    Leo, Simone; Pireddu, Luca; Cuccuru, Gianmauro; Lianas, Luca; Soranzo, Nicola; Afgan, Enis; Zanetti, Gianluigi

    2014-10-01

    BioBlend.objects is a new component of the BioBlend package, adding an object-oriented interface for the Galaxy REST-based application programming interface. It improves support for metacomputing on Galaxy entities by providing higher-level functionality and allowing users to more easily create programs to explore, query and create Galaxy datasets and workflows. BioBlend.objects is available online at https://github.com/afgane/bioblend. The new object-oriented API is implemented by the galaxy/objects subpackage. © The Author 2014. Published by Oxford University Press.

  5. Relations between blended learning possibilities and teachers' approaches to blended learning

    DEFF Research Database (Denmark)

    Stenalt, Maria Hvid; Nielsen, Tobias Alsted; Bager-Elsborg, Anna

    Higher Education has embraced blended learning as a way of enhancing quality in teaching and helping students to learn. This presentation addresses relations between blended learning possiblities presented to teachers in a teacher training project and teachers’ approaches to blended learning. We...... suggest that in order to identify the level of impact of integrating technologies in teaching and learning, we need to understand the factors influencing approaches to design of courses for blended contexts. Participants in the teacher training project come from the Department of Law at Aarhus University......: • Optain locally-embedded knowledge about blended learning • Develop opportunities for law students to receive (more) feedback • Comply with strategic aims The results so far suggest that teachers provide a disciplinary perspective on the key dimensions of blended learning, which influences...

  6. Miscibility evolution of polycarbonate/polystyrene blends during compounding

    DEFF Research Database (Denmark)

    Chuai, Chengzhi; Almdal, Kristoffer; Johannsen, Ib

    2002-01-01

    The miscibility evolution of polycarbonate/polystyrene (PC/PS) blends during the compounding process in three blending methods of industrial relevance, namely melt blending, remelt blending in a twin-screw extruder and third melt blending in an injection molding machine, was investigated...... polymer in the other. The observed solubility strongly depends on blend composition and blending method. The T-g measurements showed maximum mutual solubility around 50/50 composition. The miscibility of PC/PS blended after the third stage (melt injection molding) was higher than that after the first...... by measuring their glass transition temperatures (T-g) and their specific heat increment (DeltaC(p)). Differential scanning calorimetry (DSC) was used to examine nine blend compositions. Shifts in glass transition temperature (T-g) of the two phases in melt-mixed PC/PS blends suggest partial miscibility of one...

  7. The lure of internationalization

    DEFF Research Database (Denmark)

    Fabricius, Anne; Mortensen, Janus; Haberland, Hartmut

    2017-01-01

    with a general characterization of the discourse of mobility and internationalization in a European context, and then turn to Denmark as a specific case in which we unfold and discuss three paradoxes in turn: internationalization and linguistic pluralism, internationalization and intercultural understanding, and......, finally, internationalization and competitiveness. We then link our deconstruction of the three paradoxes to a critique of the concept of ‘parallel language policy’, widely promoted in the Nordic context, and show how it in effect undermines the ideals of internationalisation....

  8. Luring the elephants back?

    DEFF Research Database (Denmark)

    Delman, Jørgen

    to safeguard future generations. The paper updates previous work on eco-civilization construction and governance innovations in Hangzhou. The local field is increasingly politicized in response to central policies, and the room for local maneuvering is becoming increasingly regulated. Generally, the Party...... procedures based on key performance indicators and with assessments by the public are meant to improve policy implementation, also in the environmental field. It is observed how the city authorities respond to central and popular pressure by opening up to these through external participation and assessment....... This approach is seen as a key instrument to stimulate policy compliance and enhance government transparency and public accountability. However, the system of implementation still needs improvement, especially with regard to evidence based assessments of progress, compliance and effectiveness in the eco...

  9. Enzymatic degradation of polycaprolactone–gelatin blend

    International Nuclear Information System (INIS)

    Banerjee, Aditi; Chatterjee, Kaushik; Madras, Giridhar

    2015-01-01

    Blends of polycaprolactone (PCL), a synthetic polymer and gelatin, natural polymer offer a optimal combination of strength, water wettability and cytocompatibility for use as a resorbable biomaterial. The enzymatic degradation of PCL, gelatin and PCL–gelatin blended films was studied in the presence of lipase (Novozym 435, immobilized) and lysozyme. Novozym 435 degraded the PCL films whereas lysozyme degraded the gelatin. Though Novozym 435 and lysozyme individually could degrade PCL–gelatin blended films, the combination of these enzymes showed the highest degradation of these blended films. Moreover, the enzymatic degradation was much faster when fresh enzymes were added at regular intervals. The changes in physico-chemical properties of polymer films due to degradation were studied by scanning electron microscopy, Fourier transform infrared spectroscopy and differential scanning calorimetry. These results have important implications for designing resorbable biomedical implants. (paper)

  10. NESDIS Blended Total Precipitable Water (TPW) Products

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The blended Total Precipitable Water (TPW) product is derived from multiple sensors/satellites. The Percentage of TPW normal (PCT), or TPW anomaly, shows the...

  11. Strengths Weaknesses Opportunities and Threats of Blended ...

    African Journals Online (AJOL)

    students more and that facilitated a more interactive classroom environment. .... link: The evaluation of an innovative and interactive CME program, poster abstracts. ... Picciano A. Blending with purpose: The multimodal model. J Res Cent Educ ...

  12. Blended Learning in International Nuclear Education

    Energy Technology Data Exchange (ETDEWEB)

    James, Z. [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

    2012-03-15

    The spread of nuclear power ambitions beyond the few early-adopter nations requires more globalized education. Two of the learning problems specific to international education are the need for a common instructional language and different cultural styles of learning. Blended learning, a mix of personal interaction between teacher and impersonal computer-based learning, can solve these problems. The new KEPCO International Nuclear Graduate School outside Ulsan, Korea is investing heavily in blended learning.

  13. Blended Learning in International Nuclear Education

    International Nuclear Information System (INIS)

    James, Z.

    2012-01-01

    The spread of nuclear power ambitions beyond the few early-adopter nations requires more globalized education. Two of the learning problems specific to international education are the need for a common instructional language and different cultural styles of learning. Blended learning, a mix of personal interaction between teacher and impersonal computer-based learning, can solve these problems. The new KEPCO International Nuclear Graduate School outside Ulsan, Korea is investing heavily in blended learning

  14. Constructivism Based Blended Learning in Higher Education

    OpenAIRE

    Al-Huneidi, Ahmad

    2011-01-01

    Blended Learning, which is a mix of online and face-to-face learning, can combine the benefits of both, traditional classroom learning and e-learning environments.3 The aim of this thesis is to explore how to design and implement Blended Learning environment based on Constructivism theory, which focuses on students’ experience to construct the knowledge, in order to increase learning outcomes, performance, and quality in academic institutions. An affective and successful learni...

  15. Blended Interaction Spaces for Collaborative Design

    DEFF Research Database (Denmark)

    Dalsgaard, Peter; Halskov, Kim; Klokmose, Clemens Nylandsted

    During the past five years, we have explored the use, potentials and challenges of Blended Interaction spaces. In addition, we have a long background in developing and exploring methods for collaborative design. In this workshop paper, we give an overview of our work and present our visions...... and ongoing research in developing Blended Interaction spaces for collaborative design. We then identify key themes and challenges pertinent for the workshop....

  16. Blended Learning: The Student Viewpoint.

    Science.gov (United States)

    Shantakumari, N; Sajith, P

    2015-01-01

    Blended learning (BL) is defined as "a way of meeting the challenges of tailoring learning and development to the needs of individuals by integrating the innovative and technological advances offered by online learning with the interaction and participation offered in the best of traditional learning." The Gulf Medical University (GMU), Ajman, UAE, offers a number of courses which incorporate BL with contact classes and online component on an E-learning platform. Insufficient learning satisfaction has been stated as an obstacle to its implementation and efficacy. To determine the students' perceptions toward BL which in turn will determine their satisfaction and the efficacy of the courses offered. This was a cross-sectional study conducted at the GMU, Ajman between January and December 2013. Perceptions of BL process, content, and ease of use were collected from 75 students enrolled in the certificate courses offered by the university using a questionnaire. Student perceptions were assessed using Mann-Whitney U-test and Kruskal-Wallis test on the basis of gender, age, and course enrollment. The median scores of all the questions in the three domains were above three suggesting positive perceptions on BL. The distribution of perceptions was similar between gender and age. However, significant differences were observed in the course enrollment (P = 0.02). Students hold a positive perception of the BL courses being offered in this university. The difference in perceptions among students of different courses suggest that the BL format offered needs modification according to course content to improve its perception.

  17. Network reconstruction via graph blending

    Science.gov (United States)

    Estrada, Rolando

    2016-05-01

    Graphs estimated from empirical data are often noisy and incomplete due to the difficulty of faithfully observing all the components (nodes and edges) of the true graph. This problem is particularly acute for large networks where the number of components may far exceed available surveillance capabilities. Errors in the observed graph can render subsequent analyses invalid, so it is vital to develop robust methods that can minimize these observational errors. Errors in the observed graph may include missing and spurious components, as well fused (multiple nodes are merged into one) and split (a single node is misinterpreted as many) nodes. Traditional graph reconstruction methods are only able to identify missing or spurious components (primarily edges, and to a lesser degree nodes), so we developed a novel graph blending framework that allows us to cast the full estimation problem as a simple edge addition/deletion problem. Armed with this framework, we systematically investigate the viability of various topological graph features, such as the degree distribution or the clustering coefficients, and existing graph reconstruction methods for tackling the full estimation problem. Our experimental results suggest that incorporating any topological feature as a source of information actually hinders reconstruction accuracy. We provide a theoretical analysis of this phenomenon and suggest several avenues for improving this estimation problem.

  18. Morphology Evolution of Polycarbonate-Polystyrene Blends During Compounding

    DEFF Research Database (Denmark)

    Chuai, Chengzhi; Almdal, Kristoffer; Johannsen, Ib

    2001-01-01

    The morphology evolution of polycarbonate-polystyrene (PC/PS) blends during the compounding process in three blending methods of industrial relevance, namely melt blending, re-melt blending in a twin-screw extruder and tri-melt blending in an injection-moulding machine, was investigated using......-empirical model. The results show that the formation of co-continuous morphology strongly depends on blend composition and melt blending method, whereas the model prediction for phase inversion deviates from the experimental values. Further, we found that the initial mechanism of morphology evolution involves...... scanning electron microscopy (SEM) Co examine nine blend compositions. Blends were prepared at compositions where phase inversion was expected to occur according to model predictions. The experimental results were compared to the values of the point of phase inversion calculated with the semi...

  19. Blended Learning: How Teachers Balance the Blend of Online and Classroom Components

    Science.gov (United States)

    Jeffrey, Lynn M.; Milne, John; Suddaby, Gordon

    2014-01-01

    Despite teacher resistance to the use of technology in education, blended learning has increased rapidly, driven by evidence of its advantages over either online or classroom teaching alone. However, blended learning courses still fail to maximize the benefits this format offers. Much research has been conducted on various aspects of this problem,…

  20. A Phase Blending Study on Rubber Blends Based on the Solubility Preference of Curatives

    NARCIS (Netherlands)

    Guo, R.; Talma, Auke; Datta, Rabin; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

    2009-01-01

    Using previously obtained data on the solubilities of curatives in SBR, EPDM and in NBR, different mixing procedures were performed on 50/50 SBR/EPDM and NBR/EPDM blends. In contrast to a previous phase-mixing study, the curatives were added to separate phases before final blending, in an attempt to

  1. Effect of blending temperature on the mechanical properties of PVC/ENR blend upon irradiation

    International Nuclear Information System (INIS)

    Chantara Thevy Ratnam; Khairul Zaman Mohd Dahlan; Nasir, M.; Baharin, A.

    2000-01-01

    Poly (vinyl chloride) / epoxidized natural rubber blends were prepared with a Brabender plasticorder at 140, 150, 160, 170 and 180 degree C mixing temperatures. They were mixed at 50 rpm rotor speed for 10 min. The blends were irradiated with doses ranging from 0-200 kGy. Changes in tensile strength, modulus at 100% elongation, gel fraction and damping properties (tan δ) of the blends with increasing mixing temperatures and irradiation doses were investigated. In general, it was observed that the mixing temperature is important in maximizing the positive effect of irradiation. Results revealed that a readily miscible blend enjoy maximum benefit from irradiation meanwhile irradiation impart miscibility to a partially miscible PVC/ENR blend. The enhancement in blend properties is believed to be attributed by the irradiation-induced crosslinking along with irradiation-induced interaction between the polymers. The radiation-induced degradation found to be prominent at higher doses for blend that has undergone excessive thermal degradation. However evidence did not reveal the specific nature of radiation-induced reaction responsible for the improved interactions of the blends. (author)

  2. The Art of Blending: Benefits and Challenges of a Blended Course for Preservice Teachers

    Science.gov (United States)

    Shand, Kristen; Farrelly, Susan Glassett

    2018-01-01

    In this study, we explore the design and delivery of a blended social studies teaching methods course according to principles and core attributes of blended course design. In a survey at the end of the course, pre-service teachers were asked to reflect on their experience in the course, and identify the benefits and challenges of the blended…

  3. Effect of Blending on the Composition and Acceptability of Blends of ...

    African Journals Online (AJOL)

    However the blend was found deficient in lysine, leucine, iso-leucine and phenylalanine when compared with the FAO recommendations for infants. Increased levels of pigeon pea in the blend also resulted in significant increases in potassium, phosphorus, sodium, magnesium and calcium. Similarly, increased levels of ...

  4. Boll weevil (Coleoptera: Curculionidae) response to and volatilization rates of grandlure when combined with varying doses of eugenol in the extended-life pheromone lure.

    Science.gov (United States)

    Armstrong, J S

    2010-04-01

    Boll weevil, Anthonomus grandis grandis Boheman (Coleoptera: Curculionidae), trapping and pheromone quantitative analysis of extended-life pheromone lures manufactured with 0, 10, 20, and 30 mg of eugenol was conducted in the Rio Grande Valley of Texas under spring and summer conditions. Boll weevils responded positively to eugenol on one of 12 trapping weeks when densities were high, but when densities were low (30 degrees C, accumulative grandlure loss per week may be too high, leaving too little residual grandlure to effectively attract boll weevils at the end of 3 wk of trapping. Eugenol plays no role in reserving or encouraging the release of grandlure, or in increasing boll weevil captures when boll weevil densities are low.

  5. Moisture sorption and thermal characteristics of polyaramide blend fabrics

    OpenAIRE

    Genç, Gözde; Alp, Burcu; Balköse, Devrim; Ülkü, Semra; Cireli, Aysun

    2006-01-01

    Four types of fabrics woven from various polyaramid fibers of Nomex and Kevlar blends were characterized by morphology, XRD, elemental analysis, thermal analysis, and moisture adsorption isotherms. The blends consisted of Polybenzimidazole/ Kevlar blend (40% FBI and 60% Kevlar®), Nomex Delta A (blend of 60% Kevlar and 40% Nomex®), Nomex Delta T (blend of 75% Nomex, 23% Kevlar, and 2% P140 antistatic fiber), and Nomex III (fabric with a 95/5 blend of Nomex and Kevlar) containing 1% steel fiber...

  6. Blended Training for Combat Medics

    Science.gov (United States)

    Fowlkes, Jennifer; Dickinson, Sandra; Lazarus, Todd

    2010-01-01

    Bleeding from extremity wounds is the number one cause of preventable death on the battlefield and current research stresses the importance of training in preparing every Soldier to use tourniquets. HapMed is designed to provide tourniquet application training to combat medics and Soldiers using a blended training solution encompassing information, demonstration, practice, and feedback. The system combines an instrumented manikin arm, PDA, and computer. The manikin arm provides several training options including stand-alone, hands-on skills training in which soldiers can experience the actual torque required to staunch bleeding from an extremity wound and be timed on tourniquet application. This is more realistic than using a block of wood to act as a limb, which is often how training is conducted today. Combining the manikin arm with the PDA allows instructors to provide scenario based training. In a classroom or field setting, an instructor can specify wound variables such as location, casualty size, and whether the wound is a tough bleed. The PDA also allows more detailed feedback to be provided. Finally, combining the manikin arm with game-based technologies, the third component, provides opportunities to build knowledge and to practice battlefield decision making. Not only do soldiers learn how to apply a tourniquet, but when to apply a tourniquet in combat. The purpose of the paper is to describe the learning science underlying the design of HapMed, illustrate the training system and ways it is being expanded to encompass other critical life-saving tasks, and report on feedback received from instructors and trainees at military training and simulation centers.

  7. Binary blend Nanoparticles with defined morphology

    International Nuclear Information System (INIS)

    Ghazy, O.A.H.

    2008-01-01

    The word blend in linguistics means a word formed from two parts of two words. In polymer science polymer blends means polymer mixtures, a class of materials analogues to the metal alloys. Blending of polymers is a simple and economic way to create new materials meeting specific desired properties. The other alternative is to synthesize such materials eventually facing the organic chemistry design difficulties. The low entropy of mixing polymers makes the process thermodynamically unfavorable, unless there are some specific interactions between the mixed polymers. As a result, in thermal equilibrium typically a phase separation between the blend components takes place. The main challenge facing the blending of polymers is the control of the length scale of the phase separation. One of the most important applications, where the control of the phase separation is crucial for the performance is the organic solar cells. In organic solar cells a blend of an electron donating polymer and electron accepting one is formed. The dimensions of the phase separation between the two polymers should be in the range of the exciton diffusion length [1-3] (in semiconductors, exciton diffusion length is the average distance traveled by the electron-hole pair before recombination). Only under this condition the charge transfer at the interface between the two polymer layers can take place and the solar cell performs efficiently. The thin polymer blend layers for such applications are commonly deposited by spin coating from solution containing both polymers. The morphology of the thin layer prepared in this way is highly influenced by the preparation conditions such as the surface properties of the substrate, the solvent from which the blend was deposited, the temperature, and the annealing temperature [4-9]. Therefore controlling the length scale of phase separation in layers casted or spin coated from solutions is difficult and is a matter of trials and errors. Recently a novel

  8. HIGH SCHOOL STUDENTS’ VIEWS ON BLENDED LEARNING

    Directory of Open Access Journals (Sweden)

    Ibrahim Umit YAPICI,

    2012-08-01

    Full Text Available In this study, it is aimed to determine the high school students’ views on blended learning. The study was carried out in biology course for the lesson unit of “Classification of Living Things and Biodiversity” with 47 9th grade students attending Nevzat Ayaz Anatolian High School in the second term of the academic year of 2009-2010. The lessons were taught in a way appropriate to the blended learning model both via the Internet and on face-to-face basis. As the online dimension of the blended learning model, Moodle, a Learning Management System (LMS, was used. The application lasted 10 weeks. The scale of learners’ views on blended learning was applied and interviews were held to determine the views. As a result of the analysis of the scale, it was seen that their views were “highly” positive. The interviews held with the students revealed that the blended learning model provided students with various opportunities such as getting prepared for the lessons, reviewing the lessons as many times as wanted, reaching the subject-related materials without being dependent on time and place, testing oneself and communicating with the teacher and other students out of the school. The interviews also revealed that there were various problems though such as lack of Internet connection at home and problems experienced while playing the videos.

  9. Biocompatible electrospun polymer blends for biomedical applications.

    Science.gov (United States)

    Munj, Hrishikesh Ramesh; Nelson, M Tyler; Karandikar, Prathamesh Sadanand; Lannutti, John Joseph; Tomasko, David Lane

    2014-10-01

    Blends of natural and synthetic polymers have received considerable attention as biomaterials due to the potential to optimize both mechanical and bioactive properties. Electrospinning of biocompatible polymers is an efficient method producing biomimetic topographies suited to various applications. In the ultimate application, electrospun scaffolds must also incorporate drug/protein delivery for effective cell growth and tissue repair. This study explored the suitability of a ternary Polymethylmethacrylate-Polycaprolactone-gelatin blend in the preparation of electrospun scaffolds for biomedical applications. Tuning the blend composition allows control over scaffold mechanical properties and degradation rate. Significant improvements were observed in the mechanical properties of the blend compared with the individual components. In order to study drug delivery potential, triblends were impregnated with the model compound Rhodamine-B using sub/supercritical CO₂ infusion under benign conditions. Results show significantly distinct release profiles of the impregnated dye from the triblends. Specific factors such as porosity, degradation rate, stress relaxation, dye-polymer interactions, play key roles in impregnation and release. Each polymer component of the triblends shows distinct behavior during impregnation and release process. This affects the aforementioned factors and the release profiles of the dye. Careful control over blend composition and infusion conditions creates the flexibility needed to produce biocompatible electrospun scaffolds for a variety of biomedical applications. © 2014 Wiley Periodicals, Inc.

  10. Modification of polymer blends by irradiation

    International Nuclear Information System (INIS)

    Zuchowska, D.; Zagorski, Z.P.

    1999-01-01

    Modification of polymers, especially of polyolefin-elastomer blends (e. g. ethylene/propylene/diene terpolymer, ethylene propylene copolymer, ethylene/vinyl acetate copolymer etc.), by irradiation with a beam of fast electrons is discussed. Irradiation of polymer blends usually results in enhanced interactions between the constituents, caused among other things, by grafting induced at the polymer interphase. As a result, mechanical properties are affected to an extent depending on the proportion and type of constituent polymers, stabilizer content and radiation dose. Breaking strength (σ) relative elongation at break (ε) and melt flow rate (MFR), were examined for a triblock styrene/butadiene/styrene (SBS) copolymer, polypropylene (PP), and a PP-SBS blend (50:50 by wt.). In PP, the content of the crystal phase was determined. Irradiation was found to make SBS crosslink, as a result, σ rose by 25% and ε remained unaffected. PP was found to become degraded upon irradiation (MFR rose as much as 16 times), thereby σ and ε decreased considerably. In pure PP, the content of the crystal phase was found to increase. The variations of σ and ε in the irradiated PP-SBS blend follow a tendency similar to that in the SBS copolymer examined. This fact suggests the SBS copolymer to have a decisive effect on the macroscopic properties of the PP-SBS blend. (author)

  11. Designing appropriate blended courses: a students' perspective.

    Science.gov (United States)

    Tsai, Chia-Wen

    2010-10-01

    The computing education in Taiwan's vocational schools usually focuses on how to help students enhance their professional skills and pass certified examinations. In addition, due to national education policy and universities' regulations, pure online courses are not permitted in Taiwan. In order to design appropriate blended learning (BL) courses, the author explored the effects of web-mediated self-regulated learning (SRL) with variations in online class frequency on enhancing students' computing skills and their perspective of the blended courses. A total of 172 students, divided into four groups, participated in the experiment. The results showed that students in the SRL and BL group with five online classes had the highest scores for using a database management system (DBMS), and the highest pass rate on certified examinations. Students in this group also expressed their positive perspective on the arrangement of their blended course with the intervention of web-mediated SRL.

  12. Learning Design Development for Blended Learning

    DEFF Research Database (Denmark)

    Hansen, Janne Saltoft

    Learning design development for blended learning We started implementing Blackboard at Aarhus University in 2013. At the Health Faculty Blackboard replaced AULA which was a LMS with functionality for file distribution and only a vague focus on learning tools. Most teachers therefore had...... no experiences with blended leaning and technology supported out-of-class activities. At the pedagogical unit at the Health faculty we wanted to follow the Blackboard implementation with pedagogical tools for learning design to evolve the pedagogical use of the system. We needed to make development of blended...... learning courses easier for the teachers and also ensure quality in the courses. This poster describes the process from development of the learning design to implementation of the learning design at the faculty: 1. How to place demands on a learning design-model and how to develop and use such a model. 2...

  13. Preliminary assessment of blending Hanford tank wastes

    International Nuclear Information System (INIS)

    Geeting, J.G.H.; Kurath, D.E.

    1993-03-01

    A parametric study of blending Hanford tank wastes identified possible benefits from blending wastes prior to immobilization as a high level or low level waste form. Track Radioactive Components data were used as the basis for the single-shell tank (SST) waste composition, while analytical data were used for the double-shell tank (DST) composition. Limiting components were determined using the existing feed criteria for the Hanford Waste Vitrification Plant (HWVP) and the Grout Treatment Facility (GTF). Results have shown that blending can significantly increase waste loading and that the baseline quantities of immobilized waste projected for the sludge-wash pretreatment case may have been drastically underestimated, because critical components were not considered. Alternatively, the results suggest further review of the grout feed specifications and the solubility of minor components in HWVP borosilicate glass. Future immobilized waste estimates might be decreased substantially upon a thorough review of the appropriate feed specifications

  14. Preliminary assessment of blending Hanford tank wastes

    Energy Technology Data Exchange (ETDEWEB)

    Geeting, J.G.H.; Kurath, D.E.

    1993-03-01

    A parametric study of blending Hanford tank wastes identified possible benefits from blending wastes prior to immobilization as a high level or low level waste form. Track Radioactive Components data were used as the basis for the single-shell tank (SST) waste composition, while analytical data were used for the double-shell tank (DST) composition. Limiting components were determined using the existing feed criteria for the Hanford Waste Vitrification Plant (HWVP) and the Grout Treatment Facility (GTF). Results have shown that blending can significantly increase waste loading and that the baseline quantities of immobilized waste projected for the sludge-wash pretreatment case may have been drastically underestimated, because critical components were not considered. Alternatively, the results suggest further review of the grout feed specifications and the solubility of minor components in HWVP borosilicate glass. Future immobilized waste estimates might be decreased substantially upon a thorough review of the appropriate feed specifications.

  15. How Materials Support Conceptual Blending in Ideation

    DEFF Research Database (Denmark)

    Biskjaer, Michael Mose; Fischel, Aron Daniel; Dove, Graham

    2018-01-01

    as an explanatory model to pry open the complexity of this activity, showing how research on design materials improves insight into how a design concept emerges. We show this empirically in a second-by- second analysis of a card-based design ideation episode using a multi-touch surface table. We offer process......-analytical evidence for the case that manipulation of design materials helps stabilize an emerging concept, as conceptual blending research has shown by analyzing artifacts, and extend this work by showing the dynamic interplay between the emerging conceptual blend and participants’ collaborative interaction...... with the materials. Our study advances understanding of interaction with materials in design ideation and aims to facilitate future research on how materials support conceptual blending as a useful model of how design concepts emerge....

  16. SYSTEM APPROACH TO THE BLENDED LEARNING

    Directory of Open Access Journals (Sweden)

    Vladimir Kukharenko

    2015-10-01

    Full Text Available Currently, much attention is paid to the development of learning sour cream – a combination of traditional and distance (30-70% of training. Such training is sometimes called hybrid and referred to disruptive technologies. Purpose – to show that the use of systemic campaign in blended learning provides a high quality of education, and the technology can be devastating. The subject of the study – blended learning, object of study – Mixed learning process. The analysis results show that the combined training increases the motivation of students, qualification of teachers, personalized learning process. At the same time there are no reliable methods of assessing the quality of education and training standards. It is important that blended learning strategy to support the institutional goals and had an effective organizational model for support.

  17. Phase Segregation in Polystyrene?Polylactide Blends

    Energy Technology Data Exchange (ETDEWEB)

    Leung, Bonnie; Hitchcock, Adam; Brash, John; Scholl, Andreas; Doran, Andrew

    2010-06-09

    Spun-cast films of polystyrene (PS) blended with polylactide (PLA) were visualized and characterized using atomic force microscopy (AFM) and synchrotron-based X-ray photoemission electron microscopy (X-PEEM). The composition of the two polymers in these systems was determined by quantitative chemical analysis of near-edge X-ray absorption signals recorded with X-PEEM. The surface morphology depends on the ratio of the two components, the total polymer concentration, and the temperature of vacuum annealing. For most of the blends examined, PS is the continuous phase with PLA existing in discrete domains or segregated to the air?polymer interface. Phase segregation was improved with further annealing. A phase inversion occurred when films of a 40:60 PS:PLA blend (0.7 wt percent loading) were annealed above the glass transition temperature (Tg) of PLA.

  18. Crystallinity evaluation of polyhydroxybutyrate and polycaprolactone blends

    International Nuclear Information System (INIS)

    Cavalcante, Maxwell P.; Rodrigues, Elton Jorge R.; Tavares, Maria Ines B.

    2015-01-01

    Polyhydroxybutyrate, PHB, is a polymer obtained through bacterial or synthetic pathways. It has been used in the biomedical field as a matrix for drug delivery, medical implants and as scaffold material for tissue engineering. PHB has high structural organization, which makes it highly crystalline and brittle, making biodegradation difficult, reducing its employability. In order to enhance the mechanical and biological properties of PHB, blends with other polymers, biocompatible or not, are researched and produced. In this regard, blends of PHB and polycaprolactone, PCL, another biopolymer widely used in the biomedical industry, were obtained via solution casting and were characterized by X-ray diffraction (XRD), differential scanning calorimetry (DSC) and low field nuclear magnetic resonance (LF-NMR). Results have shown a dependence between PHB's crystallinity index and PCL quantity employed to obtain the blends.(author)

  19. Preparation and Properties of Polyhedral Oligosilsesquioxanes/Polymers Blends

    National Research Council Canada - National Science Library

    Blanski, Rusty

    2000-01-01

    ... (polycarbonate, SB rubber, etc.) resulting in a clear blend. We also report that aliphatic POSS compounds are also dispersible in high density polyethylene. The synthesis of POSS/polymer blends as well as some physical properties will be discussed.

  20. Model for blended learning i de tekniske uddannelser

    DEFF Research Database (Denmark)

    Ringtved, Ulla Lunde; Leth, Lilli-Ann Thomsen; Olsen, Frank

    2012-01-01

    Anvendelse af blended learning i de tekniske uddannelser i UCN med udgangspunkt i bygningskonstruktøruddannelsen......Anvendelse af blended learning i de tekniske uddannelser i UCN med udgangspunkt i bygningskonstruktøruddannelsen...

  1. Variation of long periodicity in blends of styrene butadiene, styrene ...

    Indian Academy of Sciences (India)

    relationship between long periodicity and concentration of blends. These parameters are ... tential customers for conducting polymers [10]. 2. ... Theory. The linear paracrystalline model of polymer morphology of blends comprises stacks.

  2. Composites and blends from biobased materials

    Energy Technology Data Exchange (ETDEWEB)

    Kelley, S.S. [National Renewable Energy Laboratory, Golden, CO (United States)

    1995-05-01

    The program is focused on the development of composites and blends from biobased materials to use as membranes, high value plastics, and lightweight composites. Biobased materials include: cellulose derivative microporous materials, cellulose derivative copolymers, and cellulose derivative blends. This year`s research focused on developing an improved understanding of the molecular features that cellulose based materials with improved properties for gas separation applications. Novel cellulose ester membrane composites have been developed and are being evaluated under a collaborative research agreement with Dow Chemicals Company.

  3. Blended Course with Flipped Classroom Approach

    DEFF Research Database (Denmark)

    Timcenko, Olga; Purwins, Hendrik; Triantafyllou, Evangelia

    2015-01-01

    This paper presents and analyses design decisions and development process of producing teaching materials for a blended course with flipped classroom approach at bachelor level at Aalborg University in Copenhagen, Denmark. Our experiences, as well as students’ reactions and opinions will be descr......This paper presents and analyses design decisions and development process of producing teaching materials for a blended course with flipped classroom approach at bachelor level at Aalborg University in Copenhagen, Denmark. Our experiences, as well as students’ reactions and opinions...

  4. Statistical methods for assessment of blend homogeneity

    DEFF Research Database (Denmark)

    Madsen, Camilla

    2002-01-01

    In this thesis the use of various statistical methods to address some of the problems related to assessment of the homogeneity of powder blends in tablet production is discussed. It is not straight forward to assess the homogeneity of a powder blend. The reason is partly that in bulk materials......, it is shown how to set up parametric acceptance criteria for the batch that gives a high confidence that future samples with a probability larger than a specified value will pass the USP threeclass criteria. Properties and robustness of proposed changes to the USP test for content uniformity are investigated...

  5. Reactive modification of polyesters and their blends

    Science.gov (United States)

    Wan, Chen

    2004-12-01

    As part of a broader research effort to investigate the chemical modification of polyesters by reactive processing a low molecular weight (MW) unsaturated polyester (UP) and a higher MW saturated polyester, polyethylene terephthalate (PET), alone or blended with polypropylene (PP) were melt processed in a batch mixer and continuous twin screw extruders. Modification was monitored by on-line rheology and the products were characterized primarily by off-line rheology, morphology and thermal analysis. Efforts were made to establish processing/property relationships and provide an insight of the accompanying structural changes. The overall response of the reactively modified systems was found to be strongly dependent on the component characteristics, blend composition, type and concentrations of reactive additives and processing conditions. The work concluded that UP can be effectively modified through reactive melt processing. Its melt viscosity and MW can be increased through chemical reactions between organic peroxides (POX) and chain unsaturation or between MgO and carboxyl/hydroxyl end groups. Reactive blending of PP/UP blends through peroxide modification gave finer and more uniform morphology than unreacted blends and at a given PP/UP weight ratio more thermoplastic elastomers-like rheological behavior. This is due to the continuously decreasing viscosity ratio of PP/UP towards unity by the competing reactions between POX and the blend components and formation of PP-UP copolymers which serve as in-situ compatibilizers to promote better interfacial adhesion. Kinetics of the competing reactions were analyzed through a developed model. In addition to POX concentration and mixing efficiency, rheology and morphology of UP/PP bends were significantly affected by the addition of inorganic and organic coagents. Addition of coagents such as a difunctional maleimide, MgO and/or an anhydride functionalized PP during reactive blending offers effective means for tailoring

  6. Radiation curable polymer blends for magnetic media

    International Nuclear Information System (INIS)

    Santosusso, T.M.

    1985-01-01

    Binder resins in magnetic coating formulations must fulfil a diverse set of requirements. These polymers must have the ability to accept high pigment loadings while maintaining good abrasion resistance, substrate adhesion, inherent lubricity and resistance to temperature and humidity effects. In addition, they must act as grinding aids in the dispersion of the magnetic pigment. In the thermally converted coatings now in use, these requirements are usually met by combining several polymers and crosslinking agents into an optimized blend. This approach is also effective in designing radiation curable binder systems. An overview of the methods employed to achieve such optimized blends will be discussed. (author)

  7. Blended Learning or E-learning?

    OpenAIRE

    Tayebinik, Maryam; Puteh, Marlia

    2013-01-01

    ICT or Information and Communication Technology has pervaded the fields of education.In recent years the term e-learning has emerged as a result of the integration of ICT in the education fields. Following the application this technology into teaching, some pitfalls have been identified and this have led to the Blended learning phenomenon.However the preference on this new method has been debated quite extensively.The aim of this paper is to investigate the advantages of blended learning over...

  8. Transitioning to Blended Learning: Understanding Student and Faculty Perceptions

    Science.gov (United States)

    Napier, Nannette P.; Dekhane, Sonal; Smith, Stella

    2011-01-01

    This paper describes the conversion of an introductory computing course to the blended learning model at a small, public liberal arts college. Blended learning significantly reduces face-to-face instruction by incorporating rich, online learning experiences. To assess the impact of blended learning on students, survey data was collected at the…

  9. Finding a balance in dimensions of blended learning

    NARCIS (Netherlands)

    Verkroost, M.; Meijerink, L.; Lintsen, H.W.; Veen, W.

    2008-01-01

    This article is a formative evaluation of a course in which a blended learning environment was created and a good balance in dimensions of blended learning was sought. Blended learning is defined as the total mix of pedagogical methods, using a combination of different learning strategies, both with

  10. Blended Learning and Student Engagement in an Urban High School

    Science.gov (United States)

    Johnson, Courtney

    2017-01-01

    A metropolitan school district wanted to understand blended learning as it existed in one of their high schools. Blended learning had been school-wide for four years, and district administrators wanted to know how students, teachers, and school administrators perceived blended learning and its impact on student engagement. This was a…

  11. Blended Learning Opportunities in Ukrainian IT Public Education

    Science.gov (United States)

    Szimkovics, Tamás

    2017-01-01

    Based on previous surveys the usage of ICT and blended learning is at a low level in Ukraine. To catch up with the European average, it is important to familiarize the students and teachers with blended learning in the secondary school. The information technology classes provide the best opportunity to introduce the blended learning, because they…

  12. "Comfort" as a Critical Success Factor in Blended Learning Courses

    Science.gov (United States)

    Futch, Linda S.; deNoyelles, Aimee; Thompson, Kelvin; Howard, Wendy

    2016-01-01

    There are substantial quantitative research and anecdotal reports on blended learning and blended learning courses. However, few research studies focus on what happens at the classroom level. This research study aims to consider the highly contextual environment of effective blended learning courses by identifying the strategies instructors use to…

  13. Physico-Chemical, Microbiological Profiles of Blends of Tea and ...

    African Journals Online (AJOL)

    Sample of tea obtained from Mambilla, Nigeria highland was blended with mistletoe - a known medicinal parasitic plant of cocoa. The ratios of the blends were Tea(T)/Mistletoe (M) 90:10 10:90, 75:25, 25:75, and 50:50 while ordinary tea and mistletoes served as control samples. Chemical analyses of blends were done ...

  14. Characterization of polycaprolactone and starch blends for potential ...

    African Journals Online (AJOL)

    Thermally blending starch and polycaprolactone with the compatibilizer methylenediphenyl diisocyanate (MDI) distributed in the polyester phase had been previously confirmed to enhance the mechanical properties and interface between the two phases of the blends. In this study, blends of polycaprolactone with various ...

  15. Blended Learning within an Undergraduate Exercise Physiology Laboratory

    Science.gov (United States)

    Elmer, Steven J.; Carter, Kathryn R.; Armga, Austin J.; Carter, Jason R.

    2016-01-01

    In physiological education, blended course formats (integration of face-to-face and online instruction) can facilitate increased student learning, performance, and satisfaction in classroom settings. There is limited evidence on the effectiveness of using blending course formats in laboratory settings. We evaluated the impact of blended learning…

  16. HEU to LEU conversion and blending facility: Metal blending alternative to produce LEU oxide for disposal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form more proliferation- resistant than the original form. Blending HEU (highly enriched uranium) with less-enriched uranium to form LEU has been proposed as a disposition option. Five technologies are being assessed for blending HEU. This document provides data to be used in environmental impact analysis for the HEU-LEU disposition option that uses metal blending with an oxide waste product. It is divided into: mission and assumptions, conversion and blending facility descriptions, process descriptions and requirements, resource needs, employment needs, waste and emissions from plant, hazards discussion, and intersite transportation.

  17. effect of effect of blend ratio on blend ratio on characteristics

    African Journals Online (AJOL)

    User

    properties, cassava-soybean composite, wheat, bread, blend ratio ... dily growing population, an in eating and ... thermodynamic variables can produce an effect on .... these conditions. ..... Ragaee, S. et al., Pasting properties of starch and.

  18. Structural characterization of HDPE/LLDPE blend-based nano composites obtained by different blending sequence

    International Nuclear Information System (INIS)

    Passador, Fabio R.; Ruvolo Filho, Adhemar; Pessan, Luiz A.

    2011-01-01

    The blending sequence affects the morphology formation of the nanocomposites. In this work, the blending sequences were explored to determine its influence in the rheological behavior of HDPE/LLDPE/OMMT nanocomposites. The nanocomposites were obtained by melt-intercalation using a mixture of LLDPE-g-MA and HDPE-g-MA as compatibilizer system in a torque rheometer at 180 deg C and five blending sequences were studied. The materials structures were characterized by wide angle X-ray diffraction (WAXD) and by rheological properties. The nanoclay's addition increased the shear viscosity at low shear rates, changing the behavior of HDPE/LLDPE matrix to a Bingham model behavior with an apparent yield stress. Intense interactions were obtained for the blending sequence where LLDPE and/or LLDPE-g-MA were first reinforced with organoclay since the intercalation process occurs preferentially in the amorphous phase. (author)

  19. HEU to LEU conversion and blending facility: Metal blending alternative to produce LEU oxide for disposal

    International Nuclear Information System (INIS)

    1995-09-01

    US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form more proliferation- resistant than the original form. Blending HEU (highly enriched uranium) with less-enriched uranium to form LEU has been proposed as a disposition option. Five technologies are being assessed for blending HEU. This document provides data to be used in environmental impact analysis for the HEU-LEU disposition option that uses metal blending with an oxide waste product. It is divided into: mission and assumptions, conversion and blending facility descriptions, process descriptions and requirements, resource needs, employment needs, waste and emissions from plant, hazards discussion, and intersite transportation

  20. Chitosan films and blends for packaging material

    NARCIS (Netherlands)

    Broek, van den L.A.M.; Knoop, J.R.I.; Kappen, F.H.J.; Boeriu, C.G.

    2015-01-01

    An increased interest for hygiene in everyday life as well as in food, feed and medical issues lead to a strong interest in films and blends to prevent the growth and accumulation of harmful bacteria. A growing trend is to use synthetic and natural antimicrobial polymers, to provide non-migratory

  1. BIODIESEL BLENDS IN SPACE HEATING EQUIPMENT

    International Nuclear Information System (INIS)

    KRISHNA, C.R.

    2001-01-01

    Biodiesel is a diesel-like fuel that is derived from processing vegetable oils from various sources, such as soy oil, rapeseed or canola oil, and also waste vegetable oils resulting from cooking use. Brookhaven National laboratory initiated an evaluation of the performance of blends of biodiesel and home heating oil in space heating applications under the sponsorship of the Department of Energy (DOE) through the National Renewable Energy Laboratory (NREL). This report is a result of this work performed in the laboratory. A number of blends of varying amounts of a biodiesel in home heating fuel were tested in both a residential heating system and a commercial size boiler. The results demonstrate that blends of biodiesel and heating oil can be used with few or no modifications to the equipment or operating practices in space heating. The results also showed that there were environmental benefits from the biodiesel addition in terms of reductions in smoke and in Nitrogen Oxides (NOx). The latter result was particularly surprising and of course welcome, in view of the previous results in diesel engines where no changes had been seen. Residential size combustion equipment is presently not subject to NOx regulation. If reductions in NOx similar to those observed here hold up in larger size (commercial and industrial) boilers, a significant increase in the use of biodiesel-like fuel blends could become possible

  2. A Multimodal Interaction Framework for Blended Learning

    DEFF Research Database (Denmark)

    Vidakis, Nikolaos; Kalafatis, Konstantinos; Triantafyllidis, Georgios

    2016-01-01

    Humans interact with each other by utilizing the five basic senses as input modalities, whereas sounds, gestures, facial expressions etc. are utilized as output modalities. Multimodal interaction is also used between humans and their surrounding environment, although enhanced with further senses ...... framework enabling deployment of a vast variety of modalities, tailored appropriately for use in blended learning environment....

  3. An Open Portal for Blended Learning

    DEFF Research Database (Denmark)

    Grønbæk, Kaj; Bouvin, Niels Olof; Petersen, Marianne Graves

    2004-01-01

    The combination of traditional teaching and Web-based teaching, so called blended learning, is a challenge to the teachers as well as to the students. This shift in teaching demands an openness and flexibility from the technical platform which has not been found in the existing tools. Therefore...

  4. The Effectiveness of Blended Learning Environments

    Science.gov (United States)

    Eryilmaz, Meltem

    2015-01-01

    The object of this experimental study is to measure the effectiveness of a blended learning environment which is laid out on the basis of features for face to face and online environments. The study was applied to 110 students who attend to Atilim University, Ankara, Turkey and take Introduction to Computers Course. During the application,…

  5. From E-learning to Blended Learning

    DEFF Research Database (Denmark)

    Hansen, Line Skov; Hansen, Ole

    2013-01-01

    . The project uses a ?capacity building strategy where new practice and skills are built through pedagogical interventions mostly designed as courses based on blended learning with a dialogue oriented and practice related team-work as an important part. Through this work the team learns how to use a specific...

  6. Blended learning pedagogy: the time is now!

    Science.gov (United States)

    Pizzi, Michael A

    2014-07-01

    Pedagogy is rapidly changing. To develop best practice in academia, it is important that we change with the changing needs of students. This article suggests that blended learning is one of the most important pedagogical formats that can enhance student learning, optimize the use of active learning strategies, and potentially improve student learning outcomes.

  7. CEDS Addresses: Virtual and Blended Learning

    Science.gov (United States)

    US Department of Education, 2015

    2015-01-01

    The Common Education Data Standards (CEDS) common data vocabulary supports the collection and use of information about virtual and blended learning. The data element "Virtual Indicator", introduced in version 3 of CEDS, supports a range of virtual learning-related use cases. The Virtual Indicator element may be related to a Course…

  8. Blended learning tools for teaching and training

    CERN Document Server

    Allan, Barbara

    2007-01-01

    Offers a holistic blended learning approach, combining the best of traditional approaches to learning and teaching to make best use of the advantages of each while minimizing the disadvantages. It provides information professionals with a practical guide to the design and delivery of such training programmes.

  9. Educational Ethnography in Blended Learning Environments

    Science.gov (United States)

    Antoniadou, Victoria; Dooly, Melinda

    2017-01-01

    This chapter aims to answer some of the questions that emerge when carrying out educational ethnography in a blended learning environment. The authors first outline how Virtual Ethnography (VE) has been developed and applied by other researchers. Then, to better illustrate the approach, they describe a doctoral research project that implemented…

  10. High School Students' Views on Blended Learning

    Science.gov (United States)

    Yapici, Ibrahim Umit; Akbayin, Hasan

    2012-01-01

    In this study, it is aimed to determine the high school students' views on blended learning. The study was carried out in biology course for the lesson unit of "Classification of Living Things and Biodiversity" with 47 9[superscript th] grade students attending Nevzat Ayaz Anatolian High School in the second term of the academic year of…

  11. Tribological Characteristics Evaluation of Mustard Oil Blends

    Directory of Open Access Journals (Sweden)

    Mohammed Hassan Jabal

    2018-03-01

    Full Text Available A progressive increase in the desire for environmentally friendly lubricants by users and strict government regulations for the use of these lubricants has provided an opportunity to use plant oils as biodegradable lubricants, therefore vegetable oils have been investigated to replace oil lubricants because of their maintaining the conditions of nature (environment properties. In this paper, the influences of the blending ratio of mustard seeds oil with commercial mineral oil (SAE40 on the tribological characteristics were investigated and compared with mineral oil using the four-ball tribotester. Mustard seeds oil was blended with mineral oil at a volumetric ratio ranging from 22.5 to 90%. All experimental works were confirmed to ASTM D4172-B standard. The results exhibit that some blends of mustard seeds oil with mineral oil have lower wear scar diameter, friction torque, Friction coefficient and a higher parameter of flash temperature value compared to mineral oil and neat mustard seed oil. In conclusion, the mustard seed oil blend (MU22.5 shows a better anti-wear and anti-friction performance compared to oil samples. Therefore, mustard seeds oil has the potential to be used as a lubricant of mating surfaces.

  12. Who Profits Most from Blended Learning?

    Science.gov (United States)

    Tempelaar, Dirk T.; Rienties, Bart; Giesbers, Bas

    2009-01-01

    The authors investigate the relationship between student learning choices and learning styles in the use of an innovative learning environment for statistics. For teaching introductory statistics to first-year students in economics and business, Maastricht University uses a blended learning environment. It allows students to individualize learning…

  13. Compatibilizing Bulk Polymer Blends by Using Organoclays

    Science.gov (United States)

    Si, Mayu; Gersappe, Dilip; Zhang, Wenhua; Ade, Harald; Rafailovich, Miriam; Sokolov, Jonathan; Rudomen, Gregory; Schwartz, Bradley; Fisher, Robert

    2004-03-01

    We investigated the compatiblizing performance of organoclays on melt mixed binary and tertiary polymer blends, such as, PS/PMMA, PC/SAN, PS/PMMA/PVC and PS/PMMA/PE. These polymer blends were characterized by TEM, STXM, DSC and DMA. TEM and STXM photographs show that the addition of organoclays into polymer blends drastically reduces the average domain size of the component phases. And the organoclay goes to the interfacial region between the different polymers and effectively slows down the domain size increasing during high temperature annealing. DMA and DSC results show the effect of organoclays on the mechanical properties and glass transitions temperature, which indicates the compatibilization on the molecular level. The generalized compatibilization induced by the nanoscale fillers for blends can be explained in terms of mean field models where the reduction of interfacial tension induced by in-situ grafting is counterbalanced by the increased bending energy due to the rigidity of the filler. This in turn can be shown to be a function of the degree of exfoliation, aspect ratio, and polymer filler interactions. Supported by NSF funded MRSEC at Stony Brook

  14. Blender Bikes: Blending Nutrition and Physical Activity

    Science.gov (United States)

    Ferrari, Theresa M.; Smathers, Carol A.

    2018-01-01

    Many Americans do not meet the recommendations for diet and physical activity. A blender bike can be an effective tool when coupled with hands-on activities that reinforce health recommendations. We created "Blending Nutrition and Physical Activity: An Activity Guide for Use with Blender Bikes" to use when incorporating a blender bike…

  15. Using Blended Teaching to Teach Blended Learning: Lessons Learned from Pre-Service Teachers in an Instructional Methods Course

    Science.gov (United States)

    Shand, Kristen; Farrelly, Susan Glassett

    2017-01-01

    In this study, we explore the design and delivery of a blended social studies teaching methods course to examine the elements of the blended design that pre-service teachers found most constructive. In focus groups at the completion of the course, pre-service teachers were asked to reflect on their experience in the blended course, identify the…

  16. Potential Application of ENR/EPDM Blends

    Directory of Open Access Journals (Sweden)

    B.L. Chan

    2017-06-01

    Full Text Available Since the process and conversion of natural rubber into epoxidized natural rubber (ENR was discovered and patented by I. R. Gelling of the Malaysian Rubber Product Research Association  (or now known as the Tun Razak laboratory, Brickendonbury, Hertford, in the United Kingdom, there are more than 10 000 technical and technological papers cited in the internet. Information on ENR is available, not only in the the English language but also other languages like Chinese, Malay, French, Thai and even German languages are used. NR is the most versatile and reactive rubber/elastomer. It is an advanced natural rubber which could be potentially used as a starting material for the development of other rubbers, modifie elastomers, for grafting, plastic-based materials and also thermoplastic rubbers. Its reactivity is dependent on its epoxy groups, the opening of its ring structure, and also the subsequent structures of carboxylic groups and the in-situ side-chains “carbon – carbon” double bonds (> C = C <. In some instances, up to 65% epoxidation of NR is possible and achieved for more oil resistance. For these reasons, there are many new and advanced materials which have been formed and developed in the last two decades. Among them, some of the recent research work is listed here. Apart from studies of compounding the ENR itself and its potential uses, there are many rubber-rubber blends and ENR rubber-plastics blends, some of the studies cited are “uses of new and advanced chemicals”  and synthetic rubbers:  ENR/NBR, ENR/PVC, ENR/polylactic acid blends, ENR/copolyester blends, ENR/Copolyamide Blends, ENR/poly (vinylidene fluorideblends, ENR/Carbon Nanotubes with co-agent Trimethylol Propane Triacrylate, ENR /recycled silicon materials, and ENR/copolymer of n-butyl acrylate/butyl methacrylate “grafted”. Each of these blends has its own characteristics in terms of processing, enhancement of processing like safety, scorch, oil and water

  17. HEU to LEU conversion and blending facility: UNH blending alternative to produce LEU oxide for disposal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than is the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This report provides data to be used in the environmental impact analysis for the uranyl nitrate hexahydrate blending option to produce oxide for disposal. This the Conversion and Blending Facility (CBF) alternative will have two missions (1) convert HEU materials into HEU uranyl nitrate (UNH) and (2) blend the HEU uranyl nitrate with depleted and natural assay uranyl nitrate to produce an oxide that can be stored until an acceptable disposal approach is available. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal.

  18. HEU to LEU conversion and blending facility: UNH blending alternative to produce LEU oxide for disposal

    International Nuclear Information System (INIS)

    1995-09-01

    The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than is the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This report provides data to be used in the environmental impact analysis for the uranyl nitrate hexahydrate blending option to produce oxide for disposal. This the Conversion and Blending Facility (CBF) alternative will have two missions (1) convert HEU materials into HEU uranyl nitrate (UNH) and (2) blend the HEU uranyl nitrate with depleted and natural assay uranyl nitrate to produce an oxide that can be stored until an acceptable disposal approach is available. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal

  19. Silk fibroin/pullulan blend films: Preparation and characterization

    Energy Technology Data Exchange (ETDEWEB)

    Shivananda, C. S.; Rao, B. Lakshmeesha; Madhukumar, R.; Asha, S. [Department of Studies in Physics, Mangalore University, Mangalagangotri – 574 199 (India); Sarojini, B. K. [Department of Industrial Chemistry, Mangalore University, Mangalagangotri, Mangalore –574 199 (India); Somashekhar, R. [Department of Studies in Physics, University of Mysore, Manasagangotri, Mysore – 570 006 (India); Sangappa, Y., E-mail: syhalabhavi@yahoo.co.in [Department of Studies in Physics, Mangalore University, Mangalagangotri – 574 199 (India); School of Material Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332 (United States)

    2016-05-23

    In this work silk fibroin/pullulan blend films have been prepared by solution casting method. The blend films were examined for structural, and thermal properties using X-ray diffraction (XRD), thermogravimatric (TGA) and differential scanning calorimetry (DSC) analysis. The XRD results indicate that with the introduction of pullulan, the interaction between SF and pullulan in the blend films induced the conformation transition of SF films and amorphous phase increases with increasing pullulan ratio. The thermal properties of the blend films were improved significantly in the blend films.

  20. Intermediate Ethanol Blends Catalyst Durability Program

    Energy Technology Data Exchange (ETDEWEB)

    West, Brian H; Sluder, Scott; Knoll, Keith; Orban, John; Feng, Jingyu

    2012-02-01

    In the summer of 2007, the U.S. Department of Energy (DOE) initiated a test program to evaluate the potential impacts of intermediate ethanol blends (also known as mid-level blends) on legacy vehicles and other engines. The purpose of the test program was to develop information important to assessing the viability of using intermediate blends as a contributor to meeting national goals for the use of renewable fuels. Through a wide range of experimental activities, DOE is evaluating the effects of E15 and E20 - gasoline blended with 15% and 20% ethanol - on tailpipe and evaporative emissions, catalyst and engine durability, vehicle driveability, engine operability, and vehicle and engine materials. This report provides the results of the catalyst durability study, a substantial part of the overall test program. Results from additional projects will be reported separately. The principal purpose of the catalyst durability study was to investigate the effects of adding up to 20% ethanol to gasoline on the durability of catalysts and other aspects of the emissions control systems of vehicles. Section 1 provides further information about the purpose and context of the study. Section 2 describes the experimental approach for the test program, including vehicle selection, aging and emissions test cycle, fuel selection, and data handling and analysis. Section 3 summarizes the effects of the ethanol blends on emissions and fuel economy of the test vehicles. Section 4 summarizes notable unscheduled maintenance and testing issues experienced during the program. The appendixes provide additional detail about the statistical models used in the analysis, detailed statistical analyses, and detailed vehicle specifications.

  1. Performance and emission characteristics of double biodiesel blends with diesel

    Directory of Open Access Journals (Sweden)

    Kuthalingam Arun Balasubramanian

    2013-01-01

    Full Text Available Recent research on biodiesel focused on performance of single biodiesel and its blends with diesel. The present work aims to investigate the possibilities of the application of mixtures of two biodiesel and its blends with diesel as a fuel for diesel engines. The combinations of Pongamia pinnata biodiesel, Mustard oil biodiesel along with diesel (PMD and combinations of Cotton seed biodiesel, Pongamia pinnata biodiesel along with diesel (CPD are taken for the experimental analysis. Experiments are conducted using a single cylinder direct-injection diesel engine with different loads at rated 3000 rpm. The engine characteristics of the two sets of double biodiesel blends are compared. For the maximum load, the value of Specific Fuel consumption and thermal efficiency of CPD-1 blend (10:10:80 is close to the diesel values. CPD blends give better engine characteristics than PMD blends. The blends of CPD are suitable alternative fuel for diesel in stationary/agricultural diesel engines.

  2. BLENDED LEARNING COURSE FOR FUTURE PRIMARY SCHOOL TEACHERS IMPLEMENTATION

    Directory of Open Access Journals (Sweden)

    Vira V. Kotkova

    2017-09-01

    Full Text Available Ukrainian and foreign scientists’ views on the essence of blended learning are analyzed in the article. The author's definition of a blended learning course is presented. The process of such course designing is described according to target, motivational, substantive, operational and diagnostic components. Both the structure of the blended learning course implementation as well as students’ educational-cognitive activity distribution between classroom learning and distance course are shown. The problems for students, teachers, and educational institutions of blended courses effective implementation are summarized. Students’ academic performance of three years study is analyzed. The results of students’ questioning to determine their perception of blended learning course are described according to the following categories: the effectiveness of blended course, evaluation objectivity, motivation to study, the use of plagiarism in studies, understanding of blended learning course.

  3. Performance evaluation of gamma irradiated SiR-EPDM blends

    Energy Technology Data Exchange (ETDEWEB)

    Deepalaxmi, R., E-mail: deepalaxmivaithi@gmail.com; Rajini, V.

    2014-07-01

    Highlights: • The effects of gamma irradiation on SiR-EPDM blend are examined. • Cross-linking reaction is dominant in blends C, D and E, due to higher EPDM content. • The tensile strength and hardness of blend E is improved by gamma irradiation. • The blend C and EPDM rich blends (D, E) are found to have superior performance. • Among C, D and E, suitable blend can be selected for a particular NPP application. - Abstract: Cable insulation materials (CIM) should perform their safety functions throughout their installed life in nuclear power plants (NPP). The CIM will be exposed to gamma irradiation at the installed locations. In order to forecast long-term performance of CIM, the short time accelerated testing was carried out. Due to its good mechanical strength, ethylene propylene diene monomer (EPDM) is widely used as CIM. Silicone rubber (SiR) is used in high temperature environments, due to its good di-electric properties/hydrophobicity. The blending of these two polymers may result in the improvement in their specific properties. This paper analyses the effects of gamma irradiation on the five different compositions (90-10; 70-30; 50-50; 30-70; 10-90) of SiR-EPDM blends. The blends were exposed to four different doses (25 Mrad, 100 Mrad, 200 Mrad and 250 Mrad) of gamma irradiation. The electrical and mechanical parameters like volume resistivity (VRY), surface resistivity (SRY), tensile strength (TS), elongation at break (EB), hardness (H) of the virgin and gamma irradiated blends were determined as per ASTM/IEC standards. The nature of degradation was investigated using Fourier transform infrared spectroscopy (FTIR). The simultaneous occurrence of cross-linking and chain scission is found to be the mechanism for ageing in SiR-EPDM blends. The electrical parameters such as volume resistivity and surface resistivity of all the blends are found to improve for all doses of gamma irradiation. To validate the influence of cross-linking reaction of the Si

  4. Investigation of diesel-ethanol blended fuel properties with palm methyl ester as co-solvent and blends enhancer

    Directory of Open Access Journals (Sweden)

    Mat Taib Norhidayah

    2017-01-01

    Full Text Available Diesel engine is known as the most efficient engine with high efficiency and power but always reported as high fuel emission. Malaysia National Automotive Policy (NAP was targeting to improve competitive regional focusing on green technology development in reducing the emission of the engine. Therefore, ethanol was introduced to reduce the emission of the engine and while increasing its performance, Palm methyl ester was introduced as blend enhancer to improve engine performance and improve diesel-ethanol blends stability. This paper aimed to study the characteristics of the blends and to prove the ability of palm-methyl-ester as co-solvent in ethanol-diesel blends. Stability and thermophysical test were carried out for different fuel compositions. The stability of diesel-ethanol blended was proved to be improved with the addition of PME at the longer period and the stability of the blends changed depending on temperature and ethanol content. Density and viscosity of diesel-ethanol-PME blends also give higher result than diesel-ethanol blends and it's proved that PME is able to increase density and viscosity of blends. Besides, heating value of the blends also increases with the increasing PME in diesel-ethanol blends.

  5. Field evaluation of synthetic lure (3-methyl-1-butanol) when compared to non odor-baited control in capturing Anopheles mosquitoes in varying land-use sites in Madagascar.

    Science.gov (United States)

    Zohdy, Sarah; Derfus, Kristin; Andrianjafy, Mbolatiana Tovo; Wright, Patricia C; Gillespie, Thomas R

    2015-03-07

    Malaria is the 4(th) largest cause of mortality in Madagascar. To better understand malaria transmission dynamics, it is crucial to map the distribution of the malaria vectors, mosquitoes belonging to the genus Anopheles. To do so, it is important to have a strong Anopheles-specific lure to ensure the maximum number of captures. Previous studies have isolated volatiles from the human skin microbiota and found the compound 3-methyl-1-butanol to be the most attractive to the malaria mosquito, Anopheles gambiae, in a laboratory setting; and recommended 3-methyl-1-butanol as a compound to increase An. gambiae captures in the field. To date, this compound's ability to lure wild mosquitoes in differing land-use settings has not been tested. In this study, we evaluate the role of the synthetic compound, 3-methyl-1-butanol in combination with field produced CO(2) in attracting Anopheles mosquitoes in varying land-use sites in Madagascar. CDC miniature light traps in combination with field produced CO(2) were deployed in and around six villages near Ranomafana National Park, Madagascar. To test the role of 3-methyl-1-butanol in luring Anopheles mosquitoes, two traps were set in each land-use site (village, agricultural sites, and forested habitats affiliated with each village). One was baited with the synthetic odor and the other was kept as a non-baited control. While 3-methyl-1-butanol baited traps did capture An. gambiae s.l. in this study, we did not find traps baited with synthetic 3-methyl-1-butanol to be more successful in capturing Anopheles mosquitoes, (including Anopheles gambiae s.l.) than the non odor-baited control traps in any of the land-use sites examined; however, regardless of odor bait, trapping near livestock pens resulted in the capture of significantly more Anopheles specimens. A strong synthetic lure in combination with insecticide has great potential as a mosquito control. Our findings suggest that trapping mosquitoes near livestock in malaria

  6. Tank 21 and Tank 24 Blend and Feed Study: Blending Times, Settling Times, and Transfers

    International Nuclear Information System (INIS)

    Lee, S.; Leishear, R.; Poirier, M.

    2012-01-01

    The Salt Disposition Integration (SDI) portfolio of projects provides the infrastructure within existing Liquid Waste facilities to support the startup and long term operation of the Salt Waste Processing Facility (SWPF). Within SDI, the Blend and Feed Project will equip existing waste tanks in the Tank Farms to serve as Blend Tanks where salt solutions of up to 1.2 million gallons will be blended in 1.3 million gallon tanks and qualified for use as feedstock for SWPF. In particular, Tanks 21 and 24 are planned to be used for blending and transferring to the SDI feed tank. These tanks were evaluated here to determine blending times, to determine a range of settling times for disturbed sludge, and to determine that the SWPF Waste Acceptance Criteria that less than 1200 mg/liter of solids will be entrained in salt solutions during transfers from the Tank 21 and Tank 24 will be met. Overall conclusions for Tank 21 and Tank 24 operations include: (1) Experimental correction factors were applied to CFD (computational fluid dynamics) models to establish blending times between approximately two and five hours. As shown in Phase 2 research, blending times may be as much as ten times greater, or more, if lighter fluids are added to heavier fluids (i.e., water added to salt solution). As the densities of two salt solutions converge this effect may be minimized, but additional confirmatory research was not performed. (2) At the current sludge levels and the presently planned operating heights of the transfer pumps, solids entrainment will be less than 1200 mg/liter, assuming a conservative, slow settling sludge simulant. (3) Based on theoretical calculations, particles in the density range of 2.5 to 5.0 g/mL must be greater than 2-4 (micro)m in diameter to ensure they settle adequately in 30-60 days to meet the SWPF feed criterion ( 60 days) settling times in Tank 21.

  7. Comparison of male and female emerald ash borer (Coleoptera: Buprestidae) responses to phoebe oil and (Z)-3-hexanol lures in light green prism traps

    Science.gov (United States)

    Gary G. Grant; Therese M. Poland; Tina Ciaramitaro; D. Barry Lyons; Gene C. Jones

    2011-01-01

    We conducted trapping experiments for the emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae) in Michigan, USA, and Ontario, Canada, to compare unbaited light green sticky prism traps with traps baited with phoebe oil, (Z)-3-hexenol (Z3-6:OH), or blends of other green leaf volatiles (GLVs) with Z3-6:OH. Traps were placed in the...

  8. The processing of blend words in naming and sentence reading.

    Science.gov (United States)

    Johnson, Rebecca L; Slate, Sarah Rose; Teevan, Allison R; Juhasz, Barbara J

    2018-04-01

    Research exploring the processing of morphologically complex words, such as compound words, has found that they are decomposed into their constituent parts during processing. Although much is known about the processing of compound words, very little is known about the processing of lexicalised blend words, which are created from parts of two words, often with phoneme overlap (e.g., brunch). In the current study, blends were matched with non-blend words on a variety of lexical characteristics, and blend processing was examined using two tasks: a naming task and an eye-tracking task that recorded eye movements during reading. Results showed that blend words were processed more slowly than non-blend control words in both tasks. Blend words led to longer reaction times in naming and longer processing times on several eye movement measures compared to non-blend words. This was especially true for blends that were long, rated low in word familiarity, but were easily recognisable as blends.

  9. Best Practices for Use of Blended Learning.

    Science.gov (United States)

    Margolis, Amanda R; Porter, Andrea L; Pitterle, Michael E

    2017-04-01

    Objective. To determine instructional best practice recommendations for use of blended learning from the students' perspective. Methods. Three focus groups were created, one for each of the first three years at a school of pharmacy. The focus group discussions were audio recorded and transcribed for content analysis. Results. Ten instructional best practices were identified from the focus groups: setting the stage, consistency when team teaching, timeliness in posting materials, time on task, accountability for online activities, use of structured active learning, instructor use of feedback on student preparation, incorporation of student feedback into the course, short reviews of online material during class, and ensuring technologies are user friendly. Conclusion. Instructors using blended learning should consider incorporating these best practices into their course design and management. More evaluation is needed to see if implementation of these practices affects student performance.

  10. Teaching Problem Based Learning as Blended Learning

    DEFF Research Database (Denmark)

    Kolbæk, Ditte; Nortvig, Anne-Mette

    2018-01-01

    Problem-based and project organized learning (PBL) was originally developed for collaboration between physically present students, but political decisions at many universities require that collaboration, dialogues, and other PBL activities take place online as well. With a theoretical point...... of departure in Dewey and a methodological point of departure in netnography, this study focuses on an online module at Aalborg University where teaching is based on PBL. With the research question ‘How can teachers design for PBL online,’ this study explores the teacher’s role in a six weeks’ blended learning...... program, and we present suggestions for designs for blended learning PBL based on case studies from two PBL courses...

  11. High performance concrete with blended cement

    International Nuclear Information System (INIS)

    Biswas, P.P.; Saraswati, S.; Basu, P.C.

    2012-01-01

    Principal objectives of the proposed project are two folds. Firstly, to develop the HPC mix suitable to NPP structures with blended cement, and secondly to study its durability necessary for desired long-term performance. Three grades of concrete to b considered in the proposed projects are M35, M50 and M60 with two types of blended cements, i.e. Portland slag cement (PSC) and Portland pozzolana cement (PPC). Three types of mineral admixtures - silica fume, fly ash and ground granulated blast furnace slag will be used. Concrete mixes with OPc and without any mineral admixture will be considered as reference case. Durability study of these mixes will be carried out

  12. Raman technique application for rubber blends characterization

    Directory of Open Access Journals (Sweden)

    Smitthipong, W.

    2007-11-01

    Full Text Available Raman spectroscopy has been employed in a number of studies to examine the morphological changes in a variety of materials. It is a non-destructive analysis method and an equally useful method for the investigation of material structure. Recently, Raman spectroscopy has been developed to employ as an imaging instrumentation. Sample surface scanning in X- and Y-axis and sample depth (Z-axis can be carried out by modifying the focus of the laser beam from the Raman microscope. Therefore, three-dimensional images can be thus built by using special software. The surface and bulk properties of immiscible rubber blend were investigated by Raman spectroscopy. The results obtained by Raman spectroscopy were in good agreement with those of Scanning Electron Microscope (SEM. The combination of Raman spectrometry and SEM clearly elucidates the identification of phases between the dispersed phase and the matrix (continuous phase of the immiscible rubber blends.

  13. Tribological Characteristics Evaluation of Mustard Oil Blends

    OpenAIRE

    Mohammed Hassan Jabal; Muhannad Zaidan Khalefa

    2018-01-01

    A progressive increase in the desire for environmentally friendly lubricants by users and strict government regulations for the use of these lubricants has provided an opportunity to use plant oils as biodegradable lubricants, therefore vegetable oils have been investigated to replace oil lubricants because of their maintaining the conditions of nature (environment) properties. In this paper, the influences of the blending ratio of mustard seeds oil with commercial mineral oil (SAE40) on the ...

  14. Resource consequences of reenrichment versus blending

    International Nuclear Information System (INIS)

    Owen, P.S.

    1981-01-01

    Many recent studies, including INFCE and NASAP, have concluded that recycling thermal reactor fuel reduces natural uranium requirements. These studies are based on a common set of assumptions concerning the method of recycling uranium, and consequently have produced quite similar results. It was assumed, however, that the residual uranium would be reenriched rather than blended with higher enriched uranium. This paper will examine several possible alternatives to reenriching residual uranium and discuss the consequences of each

  15. Facebook: A Versatile Platform for Blended Learning

    OpenAIRE

    Wong Ling Shing; Betty Voon Wan Niu

    2013-01-01

    Facebook is a popular networking tool among the young learners. This paper reports a practical usage of Facebook to engage learners in blended learning. The practical usage of Facebook in hosting online forums, sharing media files in vodcast, building collaborative content through Facebook Doc, and using Facebook as repository for articles and lecture notes has been described. Recent survey on 55 students revealed that a strong majority of the students agreed that Facebook has positive impact...

  16. Better together: synergy in nanocellulose blends

    Science.gov (United States)

    Mautner, Andreas; Mayer, Florian; Hervy, Martin; Lee, Koon-Yang; Bismarck, Alexander

    2017-12-01

    Cellulose nanopapers have gained significant attention in recent years as large-scale reinforcement for high-loading cellulose nanocomposites, substrates for printed electronics and filter nanopapers for water treatment. The mechanical properties of nanopapers are of fundamental importance for all these applications. Cellulose nanopapers can simply be prepared by filtering a suspension of nanocellulose, followed by heat consolidation. It was already demonstrated that the mechanical properties of cellulose nanopapers can be tailored by the fineness of the fibrils used or by modifying nanocellulose fibrils for instance by polymer adsorption, but nanocellulose blends remain underexplored. In this work, we show that the mechanical and physical properties of cellulose nanopapers can be tuned by creating nanopapers from blends of various grades of nanocellulose, i.e. (mechanically refined) bacterial cellulose or cellulose nanofibrils extracted from never-dried bleached softwood pulp by chemical and mechanical pre-treatments. We found that nanopapers made from blends of two or three nanocellulose grades show synergistic effects resulting in improved stiffness, strength, ductility, toughness and physical properties. This article is part of a discussion meeting issue `New horizons for cellulose nanotechnology'.

  17. PVA/Polysaccharides Blended Films: Mechanical Properties

    Directory of Open Access Journals (Sweden)

    Fábio E. F. Silva

    2013-01-01

    Full Text Available Blends of polyvinyl alcohol (PVA and angico gum (AG and/or cashew gum (CG were used to produce films by casting method. Morphological and mechanical properties of these films were studied and compared to the properties of a commercial collagen membrane of bovine origin (MBO. The films presented thickness varying from 70 to 140 μm (PVA/AG and 140 to 200 μm (PVA/CG. Macroscopic analysis showed that a PVA/CG film was very similar to MBO regarding the color and transparency. The higher values of tensile strength (TS and elastic modulus (EM were observed in the film. On the other hand, PVA/CG and PVA/CG-AG presented the highest value of percentage of elongation (E%. Pearson’s Correlation Analysis revealed a positive correlation between TS and EM and a negative correlation between E% and EM. The PVA/CG film presented mechanical properties very similar to MBO, with the advantage of a higher E% (11.96 than MBO (2.94. The properties of the PVA blended films depended on the polysaccharide added in the blend, as well as the acid used as a catalyst. However, all produced films presented interesting mechanical characteristics which enables several biotechnological applications.

  18. Pengembangan Pembelajaran Blended Learning Pada Generasi Z

    Directory of Open Access Journals (Sweden)

    Agus Purnomo

    2017-10-01

    Full Text Available Every generation has beliefs, values, cultures, perspectives, interests, and different skills for life and work. The generation born in the early 2000s when the rapid development of such technology referred to as generation-z or net generation. Characters of this generation is very sensitive to technology and communication, meaning they have an advantage in the field of information and knowledge development. While the educators who were born in an earlier era are still not familiar with it so that educators often claimed to be "clueless" (stuttering technology. To address this need no new innovations in the learning process so that it complies with these characters. Combines conventional learning with communication media such as whatsapp and google drive is one easy solution social studies lesson on the generation-z. Learners who are accustomed to communicate using social networks can access the material and lesson plans that have been prepared with structured each meeting. So that they can read or prepare questions before the learning begins. The proportion of the use of e-learning in this study reached 35% so that it can be summed up as learning blended learning. This learning to stand on its information technology infrastructure and can be done anytime and anywhere. So learning blended learning has characteristics that are open, flexible, and can occur anywhere. Keywords: Generation Z and blended learning   http://dx.doi.org/10.17977/um022v1i12016p070

  19. Tough Blends of Polylactide and Castor Oil

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, Megan L.; Paxton, Jessica M.; Hillmyer, Marc A. (UMM)

    2012-10-10

    Poly(l-lactide) (PLLA) is a renewable resource polymer derived from plant sugars with several commercial applications. Broader implementation of the material is limited due to its inherent brittleness. We show that the addition of 5 wt % castor oil to PLLA significantly enhances the overall tensile toughness with minimal reductions in the modulus and no plasticization of the PLLA matrix. In addition, we used poly(ricinoleic acid)-PLLA diblock copolymers, synthesized entirely from renewable resources, as compatibilizers for the PLLA/castor oil blends. Ricinoleic acid, the majority fatty acid comprising castor oil, was polymerized through a lipase-catalyzed condensation reaction. The resulting polymers contained a hydroxyl end-group that was subsequently used to initiate the ring-opening polymerization of L-lactide. The binary PLLA/castor oil blend exhibited a tensile toughness seven times greater than neat PLLA. The addition of block copolymer allowed for control over the morphology of the blends, and even further improvement in the tensile toughness was realized - an order of magnitude larger than that of neat PLLA.

  20. Properties of PET/PLA Electrospun Blends

    Science.gov (United States)

    Li, Kevin; Cebe, Peggy

    2012-02-01

    Electrospun membranes were fabricated from poly(ethylene terephthalate), PET, co-spun with poly(lactic acid), PLA. The PLA contained 2% of the D-isomer, which served to limit the overall degree of crystallinity. Membranes were deposited from blended solutions of PET/PLA in hexafluoroisopropanol. The PET/PLA composition ranged from 0/100, 75/25, 50/50, 25/75, and 100/0. Electrospun membranes were made using either a static flat plate or a rotating wheel as the counter electrode, yielding unoriented mats or highly oriented tapes, respectively. We report on our investigation of the crystallinity, crystal perfection, and mechanical properties of these materials using differential scanning calorimetry, wide and small angle X-ray scattering, and dynamic mechanical analysis. In particular, we study the ability of one blend component (PET) to crystallize in the presence of existing crystals of the second blend component (PLA) which crystallizes first and at a lower temperature than PET.

  1. Engineering Polymer Blends for Impact Damage Mitigation

    Science.gov (United States)

    Gordon, Keith L.; Smith, Russell W.; Working, Dennis C.; Siochi, Emilie J.

    2016-01-01

    Structures containing polymers such as DuPont's Surlyn® 8940, demonstrate puncture healing when impacted by a 9 millimeter projectile traveling from speeds near 300 meters per second (1,100 feet per second) to hypervelocity impacts in the micrometeoroid velocity range of 5 kilometers per second (16,000 feet per second). Surlyn® 8940 puncture heals over a temperature range of minus 30 degrees Centigrade to plus 70 degrees Centigrade and shows potential for use in pressurized vessels subject to impact damage. However, such polymers are difficult to process and limited in applicability due to their low thermal stability, poor chemical resistance and overall poor mechanical properties. In this work, several puncture healing engineered melt formulations were developed. Moldings of melt blend formulations were impacted with a 5.56 millimeter projectile with a nominal velocity of 945 meters per second (3,100 feet per second) at about 25 degrees Centigrade, 50 degrees Centigrade and 100 degrees Centigrade, depending upon the specific blend being investigated. Self-healing tendencies were determined using surface vacuum pressure tests and tensile tests after penetration using tensile dog-bone specimens (ASTM D 638-10). For the characterization of tensile properties both pristine and impacted specimens were tested to obtain tensile modulus, yield stress and tensile strength, where possible. Experimental results demonstrate a range of new puncture healing blends which mitigate damage in the ballistic velocity regime.

  2. Tough blends of polylactide and castor oil.

    Science.gov (United States)

    Robertson, Megan L; Paxton, Jessica M; Hillmyer, Marc A

    2011-09-01

    Poly(l-lactide) (PLLA) is a renewable resource polymer derived from plant sugars with several commercial applications. Broader implementation of the material is limited due to its inherent brittleness. We show that the addition of 5 wt % castor oil to PLLA significantly enhances the overall tensile toughness with minimal reductions in the modulus and no plasticization of the PLLA matrix. In addition, we used poly(ricinoleic acid)-PLLA diblock copolymers, synthesized entirely from renewable resources, as compatibilizers for the PLLA/castor oil blends. Ricinoleic acid, the majority fatty acid comprising castor oil, was polymerized through a lipase-catalyzed condensation reaction. The resulting polymers contained a hydroxyl end-group that was subsequently used to initiate the ring-opening polymerization of l-lactide. The binary PLLA/castor oil blend exhibited a tensile toughness seven times greater than neat PLLA. The addition of block copolymer allowed for control over the morphology of the blends, and even further improvement in the tensile toughness was realized-an order of magnitude larger than that of neat PLLA.

  3. The Optimum Blend: Affordances and Challenges of Blended Learning For Students

    Directory of Open Access Journals (Sweden)

    Nuray Gedik

    2012-03-01

    Full Text Available The purpose of this study was to elicit students’ perceptions regarding the most facilitative and most challenging features (affordances and barriers in a blended course design. Following the phenomenological approach of qualitative inquiry, data were collected from ten undergraduate students who had experiences in a blended learning environment. Data were collected from the students’ weekly reşection papers, interviews with students, and documents, and analyzed by structurally and texturally describing the resulting experiences and perceptions. The findings of the study indicate that used together, online and face-to-face course structures offer several opportunities and challenges for students. The participating students mentioned interaction and communication opportunities, increased motivation, increased opportunities to voice their opinions, and reinforcement of learning as the affordances in the blended learning environment. The barriers included increased workload, cultural and technical barriers, and the inter-dependence of the two environments. Implications and suggestions are offered for instructors in higher education settings

  4. The Optimum Blend: Affordances and Challenges of Blended Learning For Students

    Directory of Open Access Journals (Sweden)

    Nuray Gedik

    2012-07-01

    Full Text Available The purpose of this study was to elicit students’ perceptions regarding the most facilitative and most challenging features (affordances and barriers in a blended course design. Following the phenomenological approach of qualitative inquiry, data were collected from ten undergraduate students who had experiences in a blended learning environment. Data were collected from the students’ weekly reflection papers, interviews with students, and documents, and analyzed by structurally and texturally describing the resulting experiences and perceptions. The findings of the study indicate that used together, online and face-to-face course structures offer several opportunities and challenges for students. The participating students mentioned interaction and communication opportunities, increased motivation, increased opportunities to voice their opinions, and reinforcement of learning as the affordances in the blended learning environment. The barriers included increased workload, cultural and technical barriers, and the inter-dependence of the two environments. Implications and suggestions are offered for instructors in higher education settings.

  5. A Novel Method of Extraction of Blend Component Structure from SANS Measurements of Homopolymer Bimodal Blends.

    Science.gov (United States)

    Smerdova, Olga; Graham, Richard S; Gasser, Urs; Hutchings, Lian R; De Focatiis, Davide S A

    2014-05-01

    A new method is presented for the extraction of single-chain form factors and interchain interference functions from a range of small-angle neutron scattering (SANS) experiments on bimodal homopolymer blends. The method requires a minimum of three blends, made up of hydrogenated and deuterated components with matched degree of polymerization at two different chain lengths, but with carefully varying deuteration levels. The method is validated through an experimental study on polystyrene homopolymer bimodal blends with [Formula: see text]. By fitting Debye functions to the structure factors, it is shown that there is good agreement between the molar mass of the components obtained from SANS and from chromatography. The extraction method also enables, for the first time, interchain scattering functions to be produced for scattering between chains of different lengths. [Formula: see text].

  6. Face-to-Face Activities in Blended Learning

    DEFF Research Database (Denmark)

    Kjærgaard, Annemette

    While blended learning combines online and face-to-face teaching, research on blended learning has primarily focused on the role of technology and the opportunities it creates for engaging students. Less focus has been put on face-to-face activities in blended learning. This paper argues...... that it is not only the online activities in blended learning that provide new opportunities for rethinking pedagogy in higher education, it is also imperative to reconsider the face-to-face activities when part of the learning is provided online. Based on a review of blended learning in business and management...... education, we identify what forms of teaching and learning are suggested to take place face-to-face when other activities are moved online. We draw from the Community of Inquiry framework to analyze how face-to-face activities contribute to a blended learning pedagogy and discuss the implications...

  7. Teaching Parametric Urban Design in a Blended Learning Format

    DEFF Research Database (Denmark)

    Steinø, Nicolai

    2015-01-01

    On the basis of a theoretical discussion of the concept of blended learning, this paper presents the pre- paration, execution and evaluation of a 5 ECTS blended learning course on parametric urban design for a group of some 50 BSc students of architecture and design at Aalborg university...... and curriculum develop- ment, and di culties to nd time for research. Despite the general consensus that developing online/blended learning courses requires both technical support, complex software installations, and substantial preparation time, it is shown that free web ser- vices and low-tech adaptations...... of traditional teaching assets are su cient to get started with blended learning with only little extra e ort. While the pilot blended learning course which provided the insights for this paper has room for impro- vement, it represents a decent rst shot at developing blended learning courses for higher education...

  8. Ignition characteristics of coal blends in an entrained flow furnace

    Energy Technology Data Exchange (ETDEWEB)

    J. Faundez; B. Arias; F. Rubiera; A. Arenillas; X. Garcia; A.L. Gordon; J.J. Pis [Universidad de Concepcion, Concepcion (Chile)

    2007-09-15

    Ignition tests were carried out on blends of three coals of different rank - subbituminous, high volatile and low volatile bituminous - in two entrained flow reactors. The ignition temperatures were determined from the gas evolution profiles (CO, CO{sub 2}, NO, O{sub 2}), while the mechanism of ignition was elucidated from these profiles and corroborated by high-speed video recording. Under the experimental conditions of high carbon loading, clear interactive effects were observed for all the blends. Ignition of the lower rank coals (subbituminous, high volatile bituminous) enhanced the ignition of the higher rank coal (low volatile bituminous) in the blends. The ignition temperatures of the blends of the low rank coals (subbituminous-high volatile bituminous) were additive. However, for the rest of the blends the ignition temperatures were always closer to the lower rank coal in the blend. 21 refs., 8 figs.

  9. Oxidative stability of diacylglycerol oil and butter blends containing diacylglycerols

    DEFF Research Database (Denmark)

    Kristensen, Janni Brogaard; Nielsen, Nina Skall; Jacobsen, Charlotte

    2006-01-01

    Diacylglycerol (DAG) oils produced from sunflower oil and traditional sunflower oil were stored for 20 wk at 38 degrees C, and their oxidative stability was measured. Moreover, two butter blends were produced containing 40 wt-% DAG oil made from sunflower oil or rapeseed oil, respectively, as well...... as two control butter blends with sunflower oil or rapeseed oil. Their oxidative stability during storage at 5 degrees C for up to 12 wk was examined by similar means as for the pure oils. The storage study of the oils indicated that the DAG oil was oxidatively less stable as compared to sunflower oil......, but that they had similar sensory quality. Storage of the butter blends revealed that blends with the two types of rapeseed oil (triacylglycerol (TAG) or DAG oil) were oxidatively more stable than the blends containing oils from sunflower. There was no unambiguous indication of DAG butter blends having a different...

  10. Polyethylene/hydrophilic polymer blends for biomedical applications.

    Science.gov (United States)

    Brynda, E; Houska, M; Novikova, S P; Dobrova, N B

    1987-01-01

    Polyethylene blends with poly(2-hydroxyethyl methacrylate) [poly(HEMA)] or poly(2,3-dihydroxypropyl methacrylate) [poly(DHPMA)] were prepared by swelling polyethylene with HEMA or 2,3-epoxypropyl methacrylate (EPMA) and by polymerization of the respective monomers. Poly(EPMA) in blends was hydrolysed to poly(DHPMA) with acetic acid. The blends had similar surface and bulk compositions. Swelling with water and surface wettability were proportional to the content of the hydrophilic component; at the same content the polyethylene/poly(DHPMA) blends appeared more hydrophilic than those of polyethylene/poly(HEMA). Thrombus formation in contact with blood examined ex vivo and in vivo was considerably slower on the blends than on unmodified polyethylene. The tests indicated optima in composition; the best biological response was achieved with the blends containing about 14% poly(HEMA) or 16% poly(DHPMA).

  11. Blending effects on coal burnout and NO emissions

    Energy Technology Data Exchange (ETDEWEB)

    B. Arias; R. Backreedy; A. Arenillas; J.M. Jones; F. Rubiera; M. Pourkashanian; A. Williams; J.J. Pis [Instituto Nacional del Carbon, CSIC Oviedo (Spain)

    2003-07-01

    In this work, the combustion behaviour of individual coals of different rank and their blends was evaluated. The study was focused on burnout and NO emissions during blend combustion. Preliminary combustion tests of the coals and their blends were carried out in a thermogravimetric analyser (TGA). Some characteristic temperatures were obtained to evaluate the combustibility of the samples. These temperatures indicate an improvement in the combustibility of the less reactive coal when it is blended. An entrained flow reactor (EFR) was employed to study the behaviour of the samples at high heating rates and short residence times. Burnout and NO emissions were measured during EFR combustion tests. In some blends the results can be predicted from the weighted average of the values of the individual coals. However, other blends show an increase, from the averaged values, in burnout and especially in NO emissions. 14 refs., 10 figs., 3 tabs.

  12. Design of Sustainable Blended Products using an Integrated Methodology

    DEFF Research Database (Denmark)

    Yunus, Nor Alafiza Binti; Gernaey, Krist; Woodley, John

    2013-01-01

    This paper presents a systematic methodology for designing blended products consisting of three stages; product design, process identification and experimental verification. The product design stage is considered in this paper. The objective of this stage is to screen and select suitable chemicals...... to be used as building blocks in the mixture design, and then to propose the blend formulations that fulfill the desired product attributes. The result is a set of blends that match the constraints, the compositions, values of the target properties and information about their miscibility. The methodology has...... been applied to design several blended products. A case study on design of blended lubricants is highlighted. The objective is to identify blended products that satisfy the product attributes with at least similar or better performance compared to conventional products....

  13. Flippin' Fluid Mechanics - Comparison of Blended Classroom vs. Traditional Lecture

    Science.gov (United States)

    Webster, D. R.; Kadel, R. S.; Newstetter, W. C.

    2017-11-01

    We conducted a study of student performance in and perceptions of a blended classroom delivery of a junior-level fluid mechanics course. In the blended pedagogy, students watch short on-line videos before class, participate in interactive in-class problem solving (in dyads), and complete individualized on-line quizzes weekly. Comparisons are made among four sections of the blended classroom delivery in the period of 2013-2017 to eleven sections delivered in a traditional lecture-style format by the same instructor in 2002-2012. The results reveal dramatic improvement in student engagement, perceptions, and achievement in the blended pedagogy. For instance, the withdrawal/fail/barely-passing (WFD) rate is significantly lower for the blended classroom (8.6% vs. 16.3%; p self-perception of how-much-learned, perception of the value of the course activities, and the overall effectiveness of the course and instructor in the blended classroom.

  14. Radiation processing of thermoplastic starch by blending aromatic additives: Effect of blend composition and radiation parameters

    Science.gov (United States)

    Khandal, Dhriti; Mikus, Pierre-Yves; Dole, Patrice; Coqueret, Xavier

    2013-03-01

    This paper reports on the effects of electron beam (EB) irradiation on poly α-1,4-glucose oligomers (maltodextrins) in the presence of water and of various aromatic additives, as model blends for gaining a better understanding at a molecular level the modifications occurring in amorphous starch-lignin blends submitted to ionizing irradiation for improving the properties of this type of bio-based thermoplastic material. A series of aromatic compounds, namely p-methoxy benzyl alcohol, benzene dimethanol, cinnamyl alcohol and some related carboxylic acids namely cinnamic acid, coumaric acid, and ferulic acid, was thus studied for assessing the ability of each additive to counteract chain scission of the polysaccharide and induce interchain covalent linkages. Gel formation in EB-irradiated blends comprising of maltodextrin was shown to be dependent on three main factors: the type of aromatic additive, presence of glycerol, and irradiation dose. The chain scission versus grafting phenomenon as a function of blend composition and dose were studied using Size Exclusion Chromatography by determining the changes in molecular weight distribution (MWD) from Refractive Index (RI) chromatograms and the presence of aromatic grafts onto the maltodextrin chains from UV chromatograms. The occurrence of crosslinking was quantified by gel fraction measurements allowing for ranking the cross-linking efficiency of the additives. When applying the method to destructurized starch blends, gel formation was also shown to be strongly affected by the moisture content of the sample submitted to irradiation. The results demonstrate the possibility to tune the reactivity of tailored blend for minimizing chain degradation and control the degree of cross-linking.

  15. Structuring polymer blends with bicontinuous phase morphology. Part II. Tailoring blends with ultralow critical volume fraction

    DEFF Research Database (Denmark)

    Lyngaae-Jørgensen, Jørgen; Utracki, Leszek

    2003-01-01

    A hypothesis providing a guideline for the development of immiscible polymer blends with co-continuous phase structure at very low critical volume fraction of one component is. postulated and experimentally verified. Based on a number of simplifying assumptions the following relation was derived......: phi(cr) = k(lambdagamma)(1-z)/(theta(b)(*))(z) where lambdagamma is a Deborah number and theta(b)(*) is a dimensionless break-up time. The equation parameters, k and z are constant that depend on the flow field hence on the blending equipment. For the studies an internal mixer with Walzenkneter...

  16. Emissions characteristics of higher alcohol/gasoline blends

    International Nuclear Information System (INIS)

    Gautam, M.; Martin, D.W.; Carder, D.

    2000-01-01

    An experimental investigation was conducted to determine the emissions characteristics of higher alcohols and gasoline (UTG96) blends. While lower alcohols (methanol and ethanol) have been used in blends with gasoline, very little work has been done or reported on higher alcohols (propanol, butanol and pentanol). Comparisons of emissions and fuel characteristics between higher alcohol/gasoline blends and neat gasoline were made to determine the advantages and disadvantages of blending higher alcohols with gasoline. All tests were conducted on a single-cylinder Waukesha Cooperative Fuel Research engine operating at steady state conditions and stoichiometric air-fuel (A/F) ratio. Emissions test were conducted at the optimum spark timing-knock limiting compression ratio combination for the particular blend being tested. The cycle emission [mass per unit time (g/h)] of CO, CO 2 and organic matter hydrocarbon equivalent (OMHCE) from the higher alcohol/gasoline blends were very similar to those from neat gasoline. Cycle emissions of NO x from the blends were higher than those from neat gasoline. However, for all the emissions species considered, the brake specific emissions (g/kW h) were significantly lower for the higher alcohol/gasoline blends than for neat gasoline. This was because the blends had greater resistance to knock and allowed higher compression ratios, which increased engine power output. The contribution of alcohols and aldehydes to the overall OMHCE emissions was found to be minimal. Cycle fuel consumption (g/h) of higher alcohol/gasoline blends was slightly higher than with neat gasoline due to the lower stoichiometric A/F ratios required by the blends. However, the brake specific fuel consumption (g/kW h) for the blends was significantly lower than that for neat gasoline. (Author)

  17. Blend for visual studio 2012 by example beginner's guide

    CERN Document Server

    Shukla, Abhishek

    2015-01-01

    This book is aimed at developers and designers who are new to Blend and looking to learn Blend, not just practically, but also conceptually. This book does not assume any knowledge about Blend on the part of developers; however, some experience in design or development might be useful in understanding the concepts faster, but this book explains everything very simply so that you are able to understand everything with little or no effort.

  18. An empirical model for the melt viscosity of polymer blends

    International Nuclear Information System (INIS)

    Dobrescu, V.

    1981-01-01

    On the basis of experimental data for blends of polyethylene with different polymers an empirical equation is proposed to describe the dependence of melt viscosity of blends on component viscosities and composition. The model ensures the continuity of viscosity vs. composition curves throughout the whole composition range, the possibility of obtaining extremum values higher or lower than the viscosities of components, allows the calculation of flow curves of blends from the flow curves of components and their volume fractions. (orig.)

  19. Blended e-learning Design: Discussion of Cultural Issues

    OpenAIRE

    Ahmed A Al-Hunaiyyan; Salah AL-Sharhan; Nabeel Al-Huwail

    2008-01-01

    Blended e-learning is becoming an educational issue especially with the new development of e-learning technology and globalization. Educators as the question: can we design these systems to accommodate different cultural groups and various learning strategies. This paper addresses some design issues when selecting a blended e-learning approach; it discusses some cultural elements that affect the design of blended e-learning. The paper also explores issues related to learning design, then emph...

  20. Structural characterization of Poly aniline blended with polyacrylamide

    International Nuclear Information System (INIS)

    Fayek, S.A.; El-Sayed, S.M.; Sayed, W.M.

    2007-01-01

    Poly aniline / polyacrylamide blends in presence of different catalysts were prepared. X-ray diffraction studies reveal that the samples produced are crystalline. Optical gap of the blend in the presence of NaCIO 4 used as a catalyst is greater than that in the presence of (NH 4 ) 2 S 2 O 8 as a catalyst. The structure of polyacrylamide (PAM) blended with poly aniline (PANI) were investigated by infrared spectroscopy, Grain size was identified using scanning electron microscopy [SEM

  1. Blended learning as an effective pedagogical paradigm for biomedical science

    OpenAIRE

    Perry Hartfield

    2013-01-01

    Blended learning combines face-to-face class based and online teaching and learning delivery in order to increase flexibility in how, when, and where students study and learn. The development, integration, and promotion of blended learning in frameworks of curriculum design can optimize the opportunities afforded by information and communication technologies and, concomitantly, accommodate a broad range of student learning styles. This study critically reviews the potential benefits of blende...

  2. Performance of wet process method alternatives : terminal or continuous blend

    OpenAIRE

    Fontes, Liseane P. T. L.; Pereira, Paulo A. A.; Pais, Jorge C.; Trichês, Glicério

    2006-01-01

    This study presents the results of the research to investigate asphalt rubber mixtures produced with asphalt rubber binder obtained from two different processes; (i) terminal blend (produced in refinery); (ii) continuous blend (produced in laboratory). The experiment included the evaluation of fatigue and permanent deformation resistance of two gap graded mixtures (Caltrans ARHM -GG; ADOT AR-A C) and a dense gradation Asphalt Institute (AI) mix type IV) Two asphalt rubbers from terminal blend...

  3. Blended working: for whom it may (not work.

    Directory of Open Access Journals (Sweden)

    Nico W Van Yperen

    Full Text Available Similarly to related developments such as blended learning and blended care, blended working is a pervasive and booming trend in modern societies. Blended working combines on-site and off-site working in an optimal way to improve workers' and organizations' outcomes. In this paper, we examine the degree to which workers feel that the two defining features of blended working (i.e., time-independent working and location-independent working enhance their own functioning in their jobs. Blended working, enabled through the continuing advance and improvement of high-tech ICT software, devices, and infrastructure, may be considered beneficial for workers' perceived effectiveness because it increases their job autonomy. However, because blended working may have downsides as well, it is important to know for whom blended working may (not work. As hypothesized, in a sample of 348 workers (51.7% women, representing a wide range of occupations and organizations, we found that the perceived personal effectiveness of blended working was contingent upon workers' psychological need strength. Specifically, the perceived effectiveness of both time-independent working and location-independent working was positively related to individuals' need for autonomy at work, and negatively related to their need for relatedness and need for structure at work.

  4. Chitosan-Based Polymer Blends: Current Status and applications

    International Nuclear Information System (INIS)

    Hefian, E.A.E.; Nasef, M.M.

    2014-01-01

    This paper reviews the latest developments in chitosan-based blends and their potential applications in various fields. Various blends together with other derivatives, such as composites and graft copolymers, have been developed to overcome chitosans disadvantages, including poor mechanical properties and to improve its functionality towards specific applications. The progress made in blending chitosan with synthetic and natural polymers is presented. The versatility and unique characteristics, such as hydrophilicity, film-forming ability, biodegradability, biocompatibility, antibacterial activity and non-toxicity of chitosan has contributed to the successful development of various blends for medical, pharmaceutical, agricultural and environmental applications. (author)

  5. LENRA as compatibilizer in NR/HDPE blends

    International Nuclear Information System (INIS)

    Mahathir Mohamed; Dahlan Mohd

    2004-01-01

    Polymer blends of 60/40 NR/HDPE were prepared using Brabender PL2000 plasticorder with 60g capacity. The blends were added with radiation sensitive natural rubber (NR)-based compatibilizer, known as LENRA. They were irradiated in air with electron beam radiation at various doses. The efficacy of the compatibilizer was monitored by measuring various properties of the blends such as physical and dynamic mechanical properties including morphological studies by electron microscopic technique. Early results show that the addition of LENRA improves the properties of the TPNR blends. (Author)

  6. LENRA as compatibilizer in NR/HDPE blends

    International Nuclear Information System (INIS)

    Dahlan Mohd; Mahathir Mohamed

    2006-01-01

    Polymer blends of 60/40 NR/RDPE were prepared using Brabender PL2000 Plasticorder with 60 g capacity. The blends were added with radiation-sensitive natural rubber (NR)-based compatibilizer, known as LENRA. They were irradiated with electron-beam radiation at various doses. The efficacy of the compatibilizer was monitored by measuring various properties of the blends such as physical and dynamic mechanical properties including morphological studies by electron microscopic technique. Early results show that the addition of LENRA improves the properties of the TPNR blends. (Author)

  7. Responses of Cerambycidae and Other Insects to Traps Baited With Ethanol, 2,3-Hexanediol, and 3,2-Hydroxyketone Lures in North-Central Georgia.

    Science.gov (United States)

    Miller, D R; Crowe, C M; Mayo, P D; Silk, P J; Sweeney, J D

    2015-10-01

    In north-central Georgia, 13 species of woodboring beetles (Coleoptera: Cerambycidae: Cerambycinae) were attracted to multiple-funnel traps baited with ethanol and one of the following pheromones: (1) racemic 3-hydroxyhexan-2-one; (2) racemic 3-hydroxyoctan-2-one; and (3) syn-2,3-hexanediol. The following species were attracted to traps baited with ethanol and 3-hydroxyhexan-2-one: Anelaphus pumilus (Newman), Eburia quadrigeminata (Say), Euderces pini (Olivier), Knulliana cincta (Drury), Neoclytus mucronatus (F.), Neoclytus scutellaris (Olivier), and Xylotrechus colonus (F.). Clytus marginicollis Castelnau & Gory, and Anelaphus parallelus (Newman) were attracted to traps baited with ethanol and 3-hydroxyoctan-2-one, whereas traps baited with ethanol and syn-2,3-hexanediol were attractive to Anelaphus villosus (F.), A. parallelus, Neoclytus acuminatus (F.), Neoclytus jouteli jouteli Davis, and Megacyllene caryae (Gahan). Ethanol enhanced catches of seven cerambycid species in traps baited with syn-2,3-hexanediol and 3,2-hydroxyketones. Catches of bark and ambrosia beetles (Curculionidae: Scolytinae) in ethanol-baited traps were largely unaffected by the addition of syn-2,3-hexanediol and 3,2-hydroxyketone lures, except for two species. The mean catches of Hypothenemus rotundicollis Wood & Bright and Dryoxylon onoharaensum (Murayama) in ethanol-baited traps increased and decreased, respectively, with the addition of racemic 3-hydroxyoctan-2-one. Traps baited with ethanol and syn-2,3-hexanediol were attractive to Xylobiops basilaris (Say) (Bostrichidae) and Chariessa pilosa (Forster) (Cleridae), whereas Temnoscheila virescens (F.) (Trogossitidae) were attracted to traps baited with ethanol and 3-hydroxyhexan-2-one. The assassin bug, Apiomerus crassipes (F.) (Hemiptera: Reduviidae), was attracted to traps baited with ethanol and 3,2-hydroxyketones. Published by Oxford University Press on behalf of Entomological Society of America 2015. This work is written by US

  8. Student acceptance of blended learning in Nigeria: a case study of ...

    African Journals Online (AJOL)

    Student acceptance of blended learning in Nigeria: a case study of Landmark University. ... instrument and the acceptance of blended learning was tested using UTAUT model. ... Keywords: Blended learning, UTAUT, technology acceptance ...

  9. Blending toward Competency. Early Patterns of Blended Learning and Competency-Based Education in New Hampshire

    Science.gov (United States)

    Freeland, Julia

    2014-01-01

    As the education field strives to differentiate and personalize learning to cater to each student, two related movements are gaining attention: competency-based education and blended learning. In competency-based models, students advance on the basis of mastery, rather than according to the traditional methods of counting progress in terms of time…

  10. Cold pearl surfactant-based blends.

    Science.gov (United States)

    Crombie, R L

    1997-10-01

    Pearlizing agents have been used for many years in cosmetic formulations to add a pearlescent effect. Cold pearl surfactant-based blends are mixtures of glycol stearates and surfactants which can be blended in the cold into a wide range of personal-care formulations to create a pearlescent lustre effect. Under controlled manufacturing conditions constant viscosities and crystalline characteristics can be obtained. The development of these blends has been driven by efforts to improve the economics of adding solid pearlizing agents directly into a hot mix formulation. This paper summarizes the history of pearlizers, describes their advantages and physical chemistry of the manufacturing process. Finally some suggestions for applications are given. Les agents nacrants sont utilises depuis de nombreuses annees dans les formulations cosmetiques pour ajouter un effet nacre. Les melanges a froid a base de tensioactif nacre sont des melanges de stearates de glycol et de tensioactifs qui peuvent etre melanges a froid dans une large gamme de formulations d'hygiene personnelle pour creer un effet de lustre nacre. On peut obtenir des viscosites et des proprietes cristallines constantes avec des conditions de fabrication maitrisees. Le developpement de ces melanges a ete porte par les efforts pour ameliorer les couts de l'ajout d'agents nacrants solides directement dans une formulation melangee de l'ajout d'agents nacrants solides directement dans une formulation melangee a chaud. Cet article resume l'histoire des agents nacrants, decrit leurs avantages et al physico-chimie du procede de fabrication. On emet a la fin cetaines suggestions d'applications.

  11. Teaching European Studies: A Blended Learning Approach

    Directory of Open Access Journals (Sweden)

    Alina Christova

    2011-12-01

    Full Text Available This paper will be looking into the teaching method developed by the Institute for European Studies in Brussels, combining an e-learning tool- the E-modules- with face-to-face training sessions and webinars. The main aim is to analyse the three different components of this “blended learning” pedagogical approach, as well as the way they complement each other and to address a few of the challenges that have emerged from the experience of working with them so far. The E-modules are an e-learning platform that has been designed with the purpose of offering a structured and interactive way of learning how the European Union functions. The face-to-face training component currently takes the form of three days in-house seminars, covering in an intensive manner the most important areas of the curriculum. The lectures are held by a mix of academics and practitioners, hereby ensuring a balanced approach, in which theory and practice come together to facilitate the learning experience. The third element of the “blended learning” method is placed in-between online and face-to-face learning: interactive seminars and debates are held online, giving the participants the chance to deepen their knowledge in certain fields of interest and to discuss the content of the course with specialists and among themselves. The mixture of delivery and interaction methods was chosen in order to accommodate a large variety of target groups, ranging from students to professionals working with EU-related issues, with different backgrounds and geographical origins. One of the main challenges is to use each medium for the functionalities it is best designed for and to ensure that the various pieces of the pedagogical puzzle fit together perfectly, while allowing the learners the flexibility that had initially directed them towards “blended learning” instead of a classical classroom approach.

  12. Blended learning within an undergraduate exercise physiology laboratory.

    Science.gov (United States)

    Elmer, Steven J; Carter, Kathryn R; Armga, Austin J; Carter, Jason R

    2016-03-01

    In physiological education, blended course formats (integration of face-to-face and online instruction) can facilitate increased student learning, performance, and satisfaction in classroom settings. There is limited evidence on the effectiveness of using blending course formats in laboratory settings. We evaluated the impact of blended learning on student performance and perceptions in an undergraduate exercise physiology laboratory. Using a randomized, crossover design, four laboratory topics were delivered in either a blended or traditional format. For blended laboratories, content was offloaded to self-paced video demonstrations (∼15 min). Laboratory section 1 (n = 16) completed blended laboratories for 1) neuromuscular power and 2) blood lactate, whereas section 2 (n = 17) completed blended laboratories for 1) maximal O2 consumption and 2) muscle electromyography. Both sections completed the same assignments (scored in a blinded manner using a standardized rubric) and practicum exams (evaluated by two independent investigators). Pre- and postcourse surveys were used to assess student perceptions. Most students (∼79%) watched videos for both blended laboratories. Assignment scores did not differ between blended and traditional laboratories (P = 0.62) or between sections (P = 0.91). Practicum scores did not differ between sections (both P > 0.05). At the end of the course, students' perceived value of the blended format increased (P learning key foundational content through video demonstrations before class greatly enhanced their learning of course material compared with a preassigned reading (94% vs. 78%, P Blended exercise physiology laboratories provided an alternative method for delivering content that was favorably perceived by students and did not compromise student performance. Copyright © 2016 The American Physiological Society.

  13. [Blending powdered antineoplastic medicine in disposable ointment container].

    Science.gov (United States)

    Miyazaki, Yasunori; Uchino, Tomonobu; Kagawa, Yoshiyuki

    2014-01-01

    On dispensing powdered antineoplastic medicines, it is important to prevent cross-contamination and environmental exposure. Recently, we developed a method for blending powdered medicine in a disposable ointment container using a planetary centrifugal mixer. The disposable container prevents cross-contamination. In addition, environmental exposure associated with washing the apparatus does not arise because no blending blade is used. In this study, we aimed to confirm the uniformity of the mixture and weight loss of medicine in the blending procedure. We blended colored lactose powder with Leukerin(®) or Mablin(®) powders using the new method and the ordinary pestle and mortar method. Then, the blending state was monitored using image analysis. Blending variables, such as the blending ratio (1:9-9:1), container size (35-125 mL), and charging rate (20-50%) in the container were also investigated under the operational conditions of 500 rpm and 50 s. At a 20% charging rate in a 35 mL container, the blending precision of the mixtures was not influenced by the blending ratio, and was less than 6.08%, indicating homogeneity. With an increase in the charging rate, however, the blending precision decreased. The possible amount of both mixtures rose to about 17 g with a 20% charging rate in a 125 mL container. Furthermore, weight loss of medicines with this method was smaller than that with the pestle and mortar method, suggesting that this method is safer for pharmacists. In conclusion, we have established a precise and safe method for blending powdered medicines in pharmacies.

  14. TANK 21 AND TANK 24 BLEND AND FEED STUDY: BLENDING TIMES, SETTLING TIMES, AND TRANSFERS

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.; Leishear, R.; Poirier, M.

    2012-05-31

    The Salt Disposition Integration (SDI) portfolio of projects provides the infrastructure within existing Liquid Waste facilities to support the startup and long term operation of the Salt Waste Processing Facility (SWPF). Within SDI, the Blend and Feed Project will equip existing waste tanks in the Tank Farms to serve as Blend Tanks where salt solutions of up to 1.2 million gallons will be blended in 1.3 million gallon tanks and qualified for use as feedstock for SWPF. In particular, Tanks 21 and 24 are planned to be used for blending and transferring to the SDI feed tank. These tanks were evaluated here to determine blending times, to determine a range of settling times for disturbed sludge, and to determine that the SWPF Waste Acceptance Criteria that less than 1200 mg/liter of solids will be entrained in salt solutions during transfers from the Tank 21 and Tank 24 will be met. Overall conclusions for Tank 21 and Tank 24 operations include: (1) Experimental correction factors were applied to CFD (computational fluid dynamics) models to establish blending times between approximately two and five hours. As shown in Phase 2 research, blending times may be as much as ten times greater, or more, if lighter fluids are added to heavier fluids (i.e., water added to salt solution). As the densities of two salt solutions converge this effect may be minimized, but additional confirmatory research was not performed. (2) At the current sludge levels and the presently planned operating heights of the transfer pumps, solids entrainment will be less than 1200 mg/liter, assuming a conservative, slow settling sludge simulant. (3) Based on theoretical calculations, particles in the density range of 2.5 to 5.0 g/mL must be greater than 2-4 {micro}m in diameter to ensure they settle adequately in 30-60 days to meet the SWPF feed criterion (<1200 mg/l). (4) Experimental tests with sludge batch 6 simulant and field turbidity data from a recent Tank 21 mixing evolution suggest the solid

  15. Blended learning specialists in radiation protection

    International Nuclear Information System (INIS)

    Mayo, P.; Campayo, J. M.; Verdu, G.

    2011-01-01

    In this paper, we present a blended learning Radiation Protection Technician through an approved degree from the Polytechnic University of Valencia, which covers the knowledge and skills of functions relating to operators and supervisors in various areas and skilled workers to be to perform their work in technical units or Radiation Protection Radiation Protection Services. The benefits of this work are those related to achieving quality training flexible and adapted to follow the check off the person conducting the course, adapted to internal and external training of the applicant companies.

  16. Phase transitions in blends functionalized thermoplastics

    International Nuclear Information System (INIS)

    Grigoryeva, O.; Sergeeva, L.; Starostenko, O.; Pissis, P.

    2001-01-01

    Phase transitions, morphology and structure-property relationships in polymer blends based on functionalized thermoplastics, i.e. widely used polyurethanes and styrene-acrylic acid copolymers, were investigated by means of inter-expletive non-destructive methods. Wide and small angle X-ray scattering (WAXS and SAXS), dynamic mechanical thermal analysis, thermally stimulated depolarization currents techniques, dielectric relaxation spectroscopy and several physico-mechanical characterization techniques were used. The results obtained by the various techniques were critically compared to each other. (author)

  17. Portland blended cements: demolition ceramic waste management

    International Nuclear Information System (INIS)

    Trezza, M.A.; Zito, S.; Tironi, A.; Irassar, E.F.; Rahhal, V.F.

    2017-01-01

    Demolition ceramic wastes (DCWs) were investigated in order to determine their potential use as supplementary cementitious materials in Portland Blended Cements (PBCs). For this purpose, three ceramic wastes were investigated. After characterization of the materials used, the effect of ceramic waste replacement (8, 24 and 40% by mass) was analyzed. Pozzolanic activity, hydration progress, workability and compressive strength were determined at 2, 7 and 28 days. The results showed that the ground wastes behave as filler at an early age, but as hydration progresses, the pozzolanic activity of ceramic waste contributes to the strength requirement. [es

  18. PVA/Polysaccharides Blended Films: Mechanical Properties

    OpenAIRE

    Silva, Fábio E. F.; Di-Medeiros, Maria Carolina B.; Batista, Karla A.; Fernandes, Kátia F.

    2013-01-01

    Blends of polyvinyl alcohol (PVA) and angico gum (AG) and/or cashew gum (CG) were used to produce films by casting method. Morphological and mechanical properties of these films were studied and compared to the properties of a commercial collagen membrane of bovine origin (MBO). The films presented thickness varying from 70 to 140 μm (PVA/AG) and 140 to 200 μm (PVA/CG). Macroscopic analysis showed that a PVA/CG film was very similar to MBO regarding the color and transparency. The higher valu...

  19. Blend Analysis of HATNet Transit Candidates

    Directory of Open Access Journals (Sweden)

    Bakos G.Á.

    2011-02-01

    Full Text Available Candidate transiting planet systems discovered by wide-field groundbased surveys must go through an intensive follow-up procedure to distinguish the true transiting planets from the much more common false positives. Especially pernicious are configurations of three or more stars which produce radial velocity and light curves that are similar to those of single stars transited by a planet. In this contribution we describe the methods used by the HATNet team to reject these blends, giving a few illustrative examples.

  20. Miscibility of polymer blends with engineering models

    DEFF Research Database (Denmark)

    Vassilis, Harismiadis; van Bergen, A. R. D.; Goncalves, Ana Saraiva

    1996-01-01

    compared. The van der Waals equation of state was recently shown to accurately correlate and predict vapor-liquid and liquid-liquid equilibria for binary polymer/solvent solutions. In this work, it is demonstrated that it correlates the upper critical solution behavior of polymer blends with excellent...... accuracy using the usual mixing and combining rules and a single temperature- and composition-independent binary interaction parameter. This interaction parameter can be predicted via a generalized expression that uses only the pure component equation-of-state parameters. Using this generalized expression...

  1. BLENDED TECHNOLOGY IN LEARNING FOREIGN LANGUAGES

    Directory of Open Access Journals (Sweden)

    Natalia Alexandrovna Kameneva

    2013-11-01

    Full Text Available This article analyzes the use of information technologies in the context of a blended technology approach to learning foreign languages in higher education institutions. Distance learning tools can be categorized as being synchronous (webinar, video conferencing, case-technology, chat, ICQ, Skype, interactive whiteboards or asynchronous (blogs, forums, Twitter, video and audio podcasts, wikis, on-line testing. Sociological and psychological aspects of their application in the educational process are also considered.DOI: http://dx.doi.org/10.12731/2218-7405-2013-8-41

  2. Traitement des séquelles de brûlures de la main dans les pays à ressources limitées ; notre expérience en république démocratique du Congo

    Science.gov (United States)

    Kibadi, K.; Moutet, F.

    2015-01-01

    Summary Les séquelles de brûlures de la main sont encore fréquentes dans les pays à ressources limitées. Trente-deux patients, représentant 38 mains, ont été admis et traités, entre le 1er décembre 2010 et le 1er mai 2014 aux Cliniques Universitaires de Kinshasa en République Démocratique du Congo (RDC). nous avons observé 22 patients (69 %) dans le groupe de jeunes (patients âgés de moins de 18 ans), et 10 patients (31 %) chez les adultes (18 à 59 ans). Aucun patient dans le groupe de seniors (60 ans et plus) n’a été observé. Dans le groupe de jeunes, la tranche d’âge de 1 à 5 ans a été la plus atteinte avec 13 malades (40 %). l’accident à la maison était le plus fréquent (72 %). le mécanisme de la brûlure était le plus souvent thermique par flammes (51 %) ou par liquide chaud (34 %). les rétractions et brides sont les lésions le plus observées (84 %). la rétraction dorsale globale « main en griffe» est observée chez 40 % de patients traités, associée à des cicatrices hypertrophiques et chéloïdiennes dans 84 % de cas. Chez les 32 mains traitées chirurgicalement, des excision-greffes ont été réalisées dans 43,7 %, des lambeaux locaux dans 43,7 % et des lambeaux à distance dans 12,5 % de cas. A la sortie de l’hôpital, 84 % de « bons » résultats ont été observés. le suivi a été de 18 mois. le traitement des séquelles de brûlures de la main est possible dans ces pays, exemple de la rDC. Mais les défis à surmonter dans ces pays sont nombreux : la faible accessibilité aux techniques actuelles de la chirurgie plastique, la prise en charge initiale inadéquate des brûlures, la pauvreté. PMID:26668560

  3. Study of PP/Polybutene Blends Modified by Gamma Irradiation and HMS-PP/Polybutene Blends

    International Nuclear Information System (INIS)

    Lugao, A. B.

    2006-01-01

    The polypropylene (PP) has been applied to a wide range of production due to its various excellent properties such as cheapness, high stiffness, chemical resistance, no environmental pollution when incinerated, low specific density and good mechanical properties. However, PP is a linear polymer which exhibits low melt strength. One of the effective approaches to achieve high melt strength (HMS) is to add chain branches onto backbone polymers. High melt strength polypropylene (HMS-PP) has been recently developed and introduced in the market by the major international polypropylene producers. As a consequence different methods have been applied to modify polypropylenes by chain branches. The technology obtained by IPEN together with EMBRARAD and BRASKEM comprises chain branches added onto backbone species using gamma radiation, which is generated from a Co 6 0 source. Such radiation is very convenient in order to improve polymer materials by grafting, crosslinking and degradation. Another important approach to the development of polymer materials is based on the combination of different polymers into a new product having some of the desired properties of each component. In this work, gamma irradiation technique was used to induce chemical changes in commercial polypropylene (HMS-PP) that was after blended with polybutene and in polypropylene/polybutene blends. The samples were irradiated with a 60 C o source at doses of 12,5 and 20kGy in the presence of acetylene. It was investigated how the two different routes of blends processing can modify their properties. Indeed the results from melt flow, gel fraction and rheology reveal the influence of the process route in the blends properties. Effects on the elongation at break and break strength were observed by the results of mechanical tests. The results from rheology demonstrated an increase in melt strength and drawability of the blends

  4. Challenges Facing Blended Learning in Higher Education in Asia

    Science.gov (United States)

    Tham, Raymond; Tham, Lesley

    2013-01-01

    This paper examines the current stage of development of blended learning in higher education in China, South Korea and Japan, with a comparison to the city state of Singapore. It is noted that blended learning and e-learning are introduced at institutes of higher learning in these countries with varying

  5. Blending and nudging in fluid dynamics: some simple observations

    Energy Technology Data Exchange (ETDEWEB)

    Germano, M, E-mail: mg234@duke.edu [Department of Civil and Environmental Engineering, Duke University, Durham, NC 27708, United States of America (United States)

    2017-10-15

    Blending and nudging methods have been recently applied in fluid dynamics, particularly regarding the assimilation of experimental data into the computations. In the paper we formally derive the differential equation associated to blending and compare it to the standard nudging equation. Some simple considerations related to these techniques and their mutual relations are exposed. (paper)

  6. Encouraging User Participation in Blended Learning: Course Reorientation

    Science.gov (United States)

    Fairchild, Alea M.

    2015-01-01

    Blended learning, structured as a combination of traditional course instruction and additional supporting multimedia course content, can be used in higher education for a variety of reasons. In the case study that we examine, the introduction of blended learning was initiated three years ago with the purpose of creating more resources for…

  7. Blending in gravitational microlensing experiments : source confusion and related systematics

    NARCIS (Netherlands)

    Smith, Martin C.; Wozniak, Przemyslaw; Mao, Shude; Sumi, Takahiro

    2007-01-01

    Gravitational microlensing surveys target very dense stellar fields in the local group. As a consequence, the microlensed source stars are often blended with nearby unresolved stars. The presence of 'blending' is a cause of major uncertainty when determining the lensing properties of events towards

  8. Blended learning in health education: three case studies

    NARCIS (Netherlands)

    de Jong, N.; Savin-Baden, M.; Cunningham, A.M.; Verstegen, D.M.L.

    2014-01-01

    Blended learning in which online education is combined with face-to-face education is especially useful for (future) health care professionals who need to keep up-to-date. Blended learning can make learning more efficient, for instance by removing barriers of time and distance. In the past

  9. Optimising the Blended Learning Environment: The Arab Open University Experience

    Science.gov (United States)

    Hamdi, Tahrir; Abu Qudais, Mohammed

    2018-01-01

    This paper will offer some insights into possible ways to optimise the blended learning environment based on experience with this modality of teaching at Arab Open University/Jordan branch and also by reflecting upon the results of several meta-analytical studies, which have shown blended learning environments to be more effective than their face…

  10. A Rotational Blended Learning Model: Enhancement and Quality Assurance

    Science.gov (United States)

    Ghoul, Said

    2013-01-01

    Research on blended learning theory and practice is growing nowadays with a focus on the development, evaluation, and quality assurance of case studies. However, the enhancement of blended learning existing models, the specification of their online parts, and the quality assurance related specifically to them have not received enough attention.…

  11. Enhancing Student Teachers' Teaching Skills through a Blended Learning Approach

    Science.gov (United States)

    Albhnsawy, Abeer Abdalhalim; Aliweh, Ahmed Mahmoud

    2016-01-01

    This study investigated the effect of a blended learning program on student teachers' teaching skills in an undergraduate microteaching course. The blended learning program lasted for nine weeks. This program aimed at integrating social network tasks and face-to-face teaching activities. Pre- and post-tests were administered to assess student…

  12. Collaborative Inquiry: Expert Analysis of Blended Learning in Higher Education

    Science.gov (United States)

    Wold, Kari

    2013-01-01

    This paper reports on findings of a university focus group exploring blended learning in higher education. It first describes the findings regarding the amorphous definition of blended learning as well as whether and how universities might engage in the practice. This paper then explains the administrative, instructor, and student variables that…

  13. The Effects of Self-Paced Blended Learning of Mathematics

    Science.gov (United States)

    Balentyne, Phoebe; Varga, Mary Alice

    2016-01-01

    As online and blended learning gain more popularity in education, it becomes more important to understand their effects on student learning. The purpose of this study was to explore the effects of self-paced blended learning of mathematics on the attitudes and achievement of 26 high ability middle school students, and investigate the relationship…

  14. Blended Learning at the Boundary: Designing a New Internship

    Science.gov (United States)

    Heckman, Robert; Østerlund, Carsten S.; Saltz, Jeffrey

    2015-01-01

    This paper explores how blended learning can enhance learning at the boundary between academia and industry, and make possible the design of a new kind of internship. Boundary theory proposes that socio-cultural discontinuities between different environments create opportunities for learning. Blended learning pedagogy makes it possible to make the…

  15. Students' Opinions on Facebook Supported Blended Learning Environment

    Science.gov (United States)

    Erdem, Mukaddes; Kibar, Pinar Nuhoglu

    2014-01-01

    The first purpose of this study was to determine students' opinions on blended learning and its implementation. The other purpose was to explore the students' opinions on Facebook integration into blended learning environment. The participants of this study were 40 undergraduate students in their fourth semester of the program.…

  16. The "Tutorless" Design Studio: A Radical Experiment in Blended Learning

    Science.gov (United States)

    Hill, Glen Andrew

    2017-01-01

    This paper describes a pedagogical experiment in which a suite of novel blended learning strategies was used to replace the traditional role of design tutors in a first year architectural design studio. The pedagogical objectives, blended learning strategies and outcomes of the course are detailed. While the quality of the student design work…

  17. The Effect of Blended Learning in Mathematics Course

    Science.gov (United States)

    Lin, Ya-Wen; Tseng, Chih-Lung; Chiang, Po-Jui

    2017-01-01

    With the advent of the digital age, traditional didactic teaching and online learning have been modified and gradually replaced by "Blended Learning." The purpose of this study was to explore the influences of blended learning pedagogy on junior high school student learning achievement and the students' attitudes toward mathematics. To…

  18. A Thematic Review of Blended Learning in Higher Education

    Science.gov (United States)

    Pima, John Marco; Odetayo, Michael; Iqbal, Rahat; Sedoyeka, Eliamani

    2018-01-01

    This article reviews the international literature on blended learning in view of establishing its thematic trends in higher education. The systematic review through PRISMA, sought to answer three research questions: First, how have publications evolved from 2000 to 2016 in blended learning in higher education? Secondly, what themes are frequently…

  19. Studies on blends of cycloaliphatic epoxy resin with varying ...

    Indian Academy of Sciences (India)

    Administrator

    as well as lower mass loss of the epoxy–rubber blends with increasing rubber concentration have been observed ... vious work (Tripathi and Srivastava 2007). ... stress. The measurements were carried out at a heating rate of 10°C/min from ambient to 350°C at a fixed .... CTBN revealed increased flexibility of the blend sam-.

  20. Eudragit E100 and Polysaccharide Polymer Blends as Matrices for ...

    African Journals Online (AJOL)

    Purpose: To compare the effects of two states of polymer/polymer blending (dry and aqueous/lyophilized) on the physicomechanical properties of tablets, containing blends of locust bean gum (LB) with Eudragit® E100 (E100) and sodium carboxymethylcellulose (SCMC) as matrices. Methods: LB, SCMC and E100 were ...

  1. Production and evaluation of noodles from flour blends of cocoyam ...

    African Journals Online (AJOL)

    Flour blends were prepared from two cultivars of cocoyam ( and . ), African breadfruit ( ) and wheat ( ) at different proportions and extruded into noodles with a locally fabricated and manually operated singlescrew extruder. Proximate composition and the functional properties of the different flour blends were evaluated. The

  2. An experimental research on blended learning in the development ...

    African Journals Online (AJOL)

    The experimental research conducted for this study is based on a blended learning (BL) approach to the teaching of English as a Foreign Language (EFL) in China. The purpose of the study was to investigate the effectiveness of a blended learning approach aimed at improving students' listening and speaking skills.

  3. A study on the combustion behaviour of coal blends

    Energy Technology Data Exchange (ETDEWEB)

    Rubiera, F.; Fuente, E.; Arenillas, A.; Pis, J.J. [Instituto Nacional del Carbon, Oviedo (Spain)

    1999-07-01

    Combustion behaviour of four coals of varying rank and their binary blends was studied using temperature programmed combustion tests, and thermogravimetric analysis. Characteristic parameters could not be predicted from the weight percentage of individual coals in the blend. 6 refs., 4 figs., 1 tab.

  4. Evaluation of the ignition behaviour of coals and blends

    Energy Technology Data Exchange (ETDEWEB)

    J. Faundez; F. Rubiera; X. Garcia; A. Arenillas; A.L. Gordon; J.J. Pis [CSIC, Instituto Nacional del Carbon, Oviedo (Spain). Department of Energy and Environment

    2003-07-01

    An experimental study about ignition of coals and blends was carried out by using an entrained flow reactor (EFR) with continuous feed. Seven coals of varying rank, from subbituminous to semianthracite, were tested and evolving gases (O{sub 2}, CO, CO{sub 2}, NO) were measured. The ignition temperature was evaluated from the evolution profiles of these gases, and correlated inversely to the reactivity of coals, as reflected by increasing values of ignition temperatures in the sequence subbituminous, high volatile bituminous, low volatile bituminous and semianthracite coals. Mechanism of ignition varied from an heterogeneous mechanism (for subbituminous, low volatile bituminous and semianthracite coals) to an homogeneous mechanism (for high volatile bituminous coal). Experiments with coal blends showed that if a low volatile bituminous coal is blended with a high volatile bituminous coal, the latter determines the value of the ignition temperature and ignition mechanism of the blend, when its percentage in the blend is 50% or higher. For blends of subbituminous and high volatile bituminous coals, the ignition mechanism of the blend is determined by the ignition mechanism of the coal with a higher content in the blend. 12 refs., 9 figs., 1 tab.

  5. Effect of blending different rank coals on NOx emissions

    Energy Technology Data Exchange (ETDEWEB)

    Rubiera, F.; Esteban, R.; Arenillas, A.; Pis, J.J. [Instituto Nacional del Carbon, Oviedo (Spain)

    1999-07-01

    A study was carried out to assess the NOx emissions when the fraction of high-volatile coals in blends with low-volatile coals, such as anthracitic and semianthracitic, was increased. Burnout and NO emissions were determined for individual coals and their blends. 4 refs., 4 figs., 1 tab.

  6. Silkworm caterpillar - soybean meal blend as dietary protein source ...

    African Journals Online (AJOL)

    An experiment was conducted to evaluate the utilization of silkworm caterpillar meat (SCM) blended with soybean meal (SBM) as a dietary protein source in the practical diet of Heterobranchus bidorsalis fingerlings (M±SE=17.04±_0.02g). The fish were fed five isonitrogenous and isocaloric diets containing blends of SCM ...

  7. Exploring the Effectiveness of Blended Learning in Interior Design Education

    Science.gov (United States)

    Afacan, Yasemin

    2016-01-01

    This study explores how blended learning can contribute to interior design students' learning outcomes, their engagement with non-studio courses and affect their learning achievements. Within the framework of the study, a blended learning experience was carried out in "IAED 342 Building Performance" module at Bilkent University, Turkey.…

  8. Knocking Down Barriers: How California Superintendents Are Implementing Blended Learning

    Science.gov (United States)

    Horn, Michael B.; Gu, Anna; Evans, Meg

    2014-01-01

    School districts across the United States are implementing blended learning to boost student achievement. The authors convened several California school district superintendents to answer the questions: "What are the barriers, real or perceived, to implementing blended learning in your district?" and "Have you found solutions to or…

  9. Blended Learning as an Effective Pedagogical Paradigm for Biomedical Science

    Science.gov (United States)

    Hartfield, Perry

    2013-01-01

    Blended learning combines face-to-face class based and online teaching and learning delivery in order to increase flexibility in how, when, and where students study and learn. The development, integration, and promotion of blended learning in frameworks of curriculum design can optimize the opportunities afforded by information and communication…

  10. Student Engagement and Blended Learning: Making the Assessment Connection

    Science.gov (United States)

    Vaughan, Norman

    2014-01-01

    There is an increased focus on student engagement and blended approaches to learning in higher education. This article demonstrates how collaborative learning applications and a blended approach to learning can be used to design and support assessment activities that increase levels of student engagement with course concepts, their peers, faculty…

  11. Eudragit E100 and Polysaccharide Polymer Blends as Matrices for ...

    African Journals Online (AJOL)

    Methods: LB, SCMC and E100 were blended in their dry (as purchased) state or modified by aqueous blending and subsequent lyophilization, prior to use as matrices in tablets. ... pullulan from Aureobasidium pullulans, 3-(3,4- .... the frozen polymer before sublimation and drying). Subsequently, milling generated a more.

  12. Access Patterns of Online Materials in a Blended Course

    Science.gov (United States)

    Asarta, Carlos J.; Schmidt, James R.

    2013-01-01

    Patterns in student accesses of online materials and their effects upon student performance in a blended course are examined. Our blended course is an introductory business and economic statistics course where lectures are only available online while the traditional class period is used for complementary learning activities. Timing, volumes,…

  13. Preparation of photovoltaic cells from sexithiophene-C-60 blends

    NARCIS (Netherlands)

    Veenstra, SC; Malliaras, GG; Brouwer, HJ; Esselink, FJ; Krasnikov, VV; vanHutten, PF; Wildeman, J; Jonkman, HT; Sawatzky, GA; Hadziioannou, G; Mohlmann, GR

    1996-01-01

    Large photovoltaic responses have been recently observed in devices based on conjugated polymer-C-60 blends. Their enhanced performance, which relies on the formation of a bicontinuous network of donor-acceptor heterojunctions, is very sensitive to the morphology of the blend. In this paper, we

  14. Beyond the Factory Model: Oakland Teachers Learn How to Blend

    Science.gov (United States)

    Jacobs, Joanne

    2014-01-01

    This article describes an Oakland Unified schools program of "blended learning" that is designed to reach students who are academically all over the map. Blended learning combines brick-and-mortar schooling with online education "with some element of student control over time, place, path, and/or pace" of learning. The program…

  15. 27 CFR 24.214 - Spanish type blending sherry.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Spanish type blending... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Production of Other Than Standard Wine § 24.214 Spanish..., produced under this section, is designated “Spanish Type Blending Sherry.” Upon removal, the shipping...

  16. Ductile transition in nylon-rubber blends: influence of water

    NARCIS (Netherlands)

    Gaymans, R.J.; Borggreve, R.J.M.; Spoelstra, A.B.

    1989-01-01

    On nylon 6 and nylon 6/EPDM blends the influence of water on the glass transition temperature, mechanical properties, and the ductile transition temperature was studied. Blends of 10% and 20% were prepared with a particle size of 0.3 µm and the tensile properties, flexural moduli, torsion moduli,

  17. Effect of Blend Ratio on Thermo-Physical and Sensory ...

    African Journals Online (AJOL)

    Thermo-physical properties of bread made from wheat, cassava and soybean blends were investigated. During investigation, the organoleptic acceptance of the composite wheat, cassava and soy bread was determined. All the blend ratios were exposed to equal heating rate during baking at set temperature of 230oC. The ...

  18. Assessing the Acceptance of a Blended Learning University Course

    Science.gov (United States)

    Tselios, Nikolaos; Daskalakis, Stelios; Papadopoulou, Maria

    2011-01-01

    Usefulness and ease of use proved to be key determinants of the acceptance and usage of e-learning. On the contrary, little is known about students' perceptions in a blended learning setting. In this paper, the Technology Acceptance Model (TAM) was utilised, in order to investigate Greek university students' attitudes toward blended learning. The…

  19. Radiation crosslinked block copolymer blends with improved impact resistance

    International Nuclear Information System (INIS)

    Saunders, F.L.; Pelletier, R.R.

    1976-01-01

    Polymer blends having high impact resistance after mechanical working are produced by blending together a non-elastomeric monovinylidene aromatic polymer such as polystyrene with an elastomeric copolymer, such as a block copolymer of styrene and butadiene, in the form of crosslinked, colloidal size particles

  20. Blending and nudging in fluid dynamics: some simple observations

    International Nuclear Information System (INIS)

    Germano, M

    2017-01-01

    Blending and nudging methods have been recently applied in fluid dynamics, particularly regarding the assimilation of experimental data into the computations. In the paper we formally derive the differential equation associated to blending and compare it to the standard nudging equation. Some simple considerations related to these techniques and their mutual relations are exposed. (paper)

  1. Blending and nudging in fluid dynamics: some simple observations

    Science.gov (United States)

    Germano, M.

    2017-10-01

    Blending and nudging methods have been recently applied in fluid dynamics, particularly regarding the assimilation of experimental data into the computations. In the paper we formally derive the differential equation associated to blending and compare it to the standard nudging equation. Some simple considerations related to these techniques and their mutual relations are exposed.

  2. A drop penetration method to measure powder blend wettability.

    Science.gov (United States)

    Wang, Yifan; Liu, Zhanjie; Muzzio, Fernando; Drazer, German; Callegari, Gerardo

    2018-03-01

    Water wettability of pharmaceutical blends affects important quality attributes of final products. We investigate the wetting properties of a pharmaceutical blend lubricated with Magnesium Stearate (MgSt) as a function of the mechanical shear strain applied to the blend. We measure the penetration dynamics of sessile drops deposited on slightly compressed powder beds. We consider a blend composed of 9% Acetaminophen 90% Lactose and 1% MgSt by weight. Comparing the penetration time of water and a reference liquid Polydimethylsiloxane (silicon oil) we obtain an effective cosine of the contact angle with water, based on a recently developed drop penetration method. We repeat the experiments for blends exposed to increasing levels of shear strain and demonstrate a significant decrease in water wettability (decrease in the cosine of the contact angle). The results are consistent with the development of a hydrophobic film coating the powder particles as a result of the increased shear strain. Finally, we show that, as expected dissolution times increase with the level of shear strain. Therefore, the proposed drop penetration method could be used to directly assess the state of lubrication of a pharmaceutical blend and act as a quality control on powder blend attributes before the blend is tableted. Copyright © 2017 Elsevier B.V. All rights reserved.

  3. Shearing of particles during crack growth in polymer blends

    NARCIS (Netherlands)

    Pijnenburg, K.G.W.; Steenbrink, A.C.; Giessen, E.V.D.

    1999-01-01

    Microstructural investigations below the fracture surface have revealed that the rubber particles in a number of polymer-rubber blends were deformed into remarkable S-like shapes. These shapes seem to have been largely ignored in previous microstructural studies of blends, but in fact cannot be

  4. Blended Learning: Deficits and Prospects in Higher Education

    Science.gov (United States)

    Cuesta Medina, Liliana

    2018-01-01

    This article examines the nature and evolution of the term blended learning (BL), which encompasses numerous connotations, including its conception as a strategy, delivery mode, opportunity, educational shift, or pedagogical approach. Although much has been said in this field, very few studies examine the different types of blends behind their…

  5. Biodigestion of cassava peels blended with pig dung for methane ...

    African Journals Online (AJOL)

    Biodigestion of the wastes blends and control was carried out simultaneously under the same environmental and operational conditions of 30 days retention period using four metallic biodigesters of 32 L capacity each. The biogas yield result shows that blend 2 yielded the highest cumulative biogas of 78.5 L, while the least ...

  6. Blended synchronous learning environment: Student perspectives

    Directory of Open Access Journals (Sweden)

    Conklina Sheri

    2017-06-01

    Full Text Available Distance education environments can take many forms, from asynchronous to blended synchronous environments. Blended synchronous learning environment (BSLE can be defined as an innovative setting in which students can decide to attend classes either face-to-face or via a synchronous virtual connection. Many educators are unfamiliar teaching in BSLE because of lack of experience or exposure to this delivery method. Thus, it is important to understand the optimal organisational structures and the effective management of BSLE courses to facilitate student learning and interaction. Seeking to understand this teaching method, an exploratory mixed-method study was conducted to examine graduate students’ perceptions of the BSLE. Quantitative and qualitative data was collected from a questionnaire and analysed. The findings revealed that students were satisfied with the BSLE, interactions, and the instructor. However, findings showed that the instructor divided attention between face-to-face and online synchronous students, which can cause cognitive overload and compromise the quality of instruction. Additionally, this study suggests that technical difficulties can affect students’ satisfaction with BSLE courses. Implications for further research and limitations are discussed.

  7. Blending Online Asynchronous and Synchronous Learning

    Directory of Open Access Journals (Sweden)

    Lisa C. Yamagata-Lynch

    2014-04-01

    Full Text Available In this article I will share a qualitative self-study about a 15-week blended 100% online graduate level course facilitated through synchronous meetings on Blackboard Collaborate and asynchronous discussions on Blackboard. I taught the course at the University of Tennessee (UT during the spring 2012 semester and the course topic was online learning environments. The primary research question of this study was: How can the designer/instructor optimize learning experiences for students who are studying about online learning environments in a blended online course relying on both synchronous and asynchronous technologies? I relied on student reflections of course activities during the beginning, middle, and the end of the semester as the primary data source to obtain their insights regarding course experiences. Through the experiences involved in designing and teaching the course and engaging in this study I found that there is room in the instructional technology research community to address strategies for facilitating online synchronous learning that complement asynchronous learning. Synchronous online whole class meetings and well-structured small group meetings can help students feel a stronger sense of connection to their peers and instructor and stay engaged with course activities. In order to provide meaningful learning spaces in synchronous learning environments, the instructor/designer needs to balance the tension between embracing the flexibility that the online space affords to users and designing deliberate structures that will help them take advantage of the flexible space.

  8. Chitosan films and blends for packaging material.

    Science.gov (United States)

    van den Broek, Lambertus A M; Knoop, Rutger J I; Kappen, Frans H J; Boeriu, Carmen G

    2015-02-13

    An increased interest for hygiene in everyday life as well as in food, feed and medical issues lead to a strong interest in films and blends to prevent the growth and accumulation of harmful bacteria. A growing trend is to use synthetic and natural antimicrobial polymers, to provide non-migratory and non-depleting protection agents for application in films, coatings and packaging. In food packaging, antimicrobial effects add up to the barrier properties of the materials, to increase the shelf life and product quality. Chitosan is a natural bioactive polysaccharide with intrinsic antimicrobial activity and, due to its exceptional physicochemical properties imparted by the polysaccharide backbone, has been recognized as a natural alternative to chemically synthesized antimicrobial polymers. This, associated with the increasing preference for biofunctional materials from renewable resources, resulted in a significant interest on the potential for application of chitosan in packaging materials. In this review we describe the latest developments of chitosan films and blends as packaging material. Copyright © 2014 Elsevier Ltd. All rights reserved.

  9. Selected physical properties of various diesel blends

    Science.gov (United States)

    Hlaváčová, Zuzana; Božiková, Monika; Hlaváč, Peter; Regrut, Tomáš; Ardonová, Veronika

    2018-01-01

    The quality determination of biofuels requires identifying the chemical and physical parameters. The key physical parameters are rheological, thermal and electrical properties. In our study, we investigated samples of diesel blends with rape-seed methyl esters content in the range from 3 to 100%. In these, we measured basic thermophysical properties, including thermal conductivity and thermal diffusivity, using two different transient methods - the hot-wire method and the dynamic plane source. Every thermophysical parameter was measured 100 times using both methods for all samples. Dynamic viscosity was measured during the heating process under the temperature range 20-80°C. A digital rotational viscometer (Brookfield DV 2T) was used for dynamic viscosity detection. Electrical conductivity was measured using digital conductivity meter (Model 1152) in a temperature range from -5 to 30°C. The highest values of thermal parameters were reached in the diesel sample with the highest biofuel content. The dynamic viscosity of samples increased with higher concentration of bio-component rapeseed methyl esters. The electrical conductivity of blends also increased with rapeseed methyl esters content.

  10. Mechanical and thermal properties of physically-blended-plastic films

    International Nuclear Information System (INIS)

    Abu Issa, M. S.

    1983-10-01

    Low density polyethylene (LDPE) and isotactic polypropylene (PP) blend were produced in film form and were characterized by a number of techniques such as wide-angle x-ray diffraction (WAXD), differential thermal analysis (DTA), scanning electron microscopy (SEM), and instron tensile testing. Results of WAXD and DTA showed conclusively that the two components in the blend are incompatible. SEM micrographs indicated that the 60/40 and 40/60 PP/PE blends show approximately fine homogeneous dispersion of the minor component into the matrix of the major component. The mechanical properties of the blend films improved with respect to the PE homo polymer. The improvement was more remarkable with the increase of the PP component in the blend. Results obtained in this work were explained in terms of crystallinity and the crystallite orientation. 28 refs., 29 figs., 5 tabs. (A.M.H.)

  11. A blend of Sodium Humate/SLES/Herbal Oils

    Directory of Open Access Journals (Sweden)

    Yeliz Akyiğit

    2013-08-01

    Full Text Available A blend of sodium humate (SH with anionic surfactants such as sodium lauryl ether sulfate (SLES was prepared by solution mixing at medium of herbal oils at 25, 50 and 75°C. Its miscibility studies were carried out by using physical techniques over an extended range of concentration and composition in buffer solution. In addition, to ascertain the state of miscibility of the blends, they were investigated by using UV-visible spectrophotometer and Fourier transform infrared (FTIR. These values revealed that the blend is miscible when the sodium humate content is more than %60 in the blend at all temperatures. There were no important differences in the characteristics of the blends at different temperatures.It was thought that the mechanism ofthe complex formation is realized by making strong intermolecular interaction like hydrogen bonds between the carbonyl groups in humic acid and hydroxyl groups in fatty acids.

  12. Modification of combustion behaviour and NO emissions by coal blending

    Energy Technology Data Exchange (ETDEWEB)

    Rubiera, Fernando; Arenillas, Ana; Arias, Borja; Pis, Jose J. [Department of Energy and Environment, Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain)

    2002-06-20

    Combustion profiles determined by TGA and experiments in a laminar entrained flow reactor (EFR) were used in this work to assess the relative combustion reactivities of different rank coals and their binary coal blends. The combustion behaviour of coal blends in TGA was greatly influenced by coal rank and the proportion of each component in the blend. Higher volatile coals exerted more influence in the low-temperature region and less reactive coals in the char combustion zone. The results in the EFR indicated that coal blends burnout and NO emissions show additivity in the case of similar nature coals. When one of the components was a high-rank coal, the burnout of the blend exhibited, in some cases, positive synergistic effects, while a clear deviation from linearity was found in NO emissions.

  13. NOx emissions and combustibility characteristics of coal blends

    Energy Technology Data Exchange (ETDEWEB)

    Rubiera, F.; Arenillas, A.; Arias, B.; Pis, J.J. [CSIC, Instituto Nacional del Carbon, Oviedo (Spain). Dept. of Energy and Environment

    2001-07-01

    In this work, a series of coals with different origin and rank were blended and several aspects of the resultant blends were studied. This included determination of the grindability of individual coals and blends by means of the Hardgrove Grindability Index (HGI), and temperature programmed combustion test, which were carried out in a thermogravimetric analyser (TG) coupled to a quadruple mass spectrometer (MS) for evolved gas analysis. Special attention was paid to the combustibility parameters and the NO emissions during blends combustion. It was found that while some coal blends present interaction between the individual coals, others do not. This behaviour was assumed to be due to the differences in coal structure and functional groups composition. 18 refs., 11 figs., 2 tabs.

  14. Perception of blended learning inventory (POBLI) - development and validation

    DEFF Research Database (Denmark)

    Lassesen, Berit; Rossen, Dorte Sidelmann; Stenalt, Maria Hvid

    and explore how the use of blended learning affects teachers’ approaches to teaching and students’ approaches to learning in higher education. So far, there has been relatively limited research on approaches to teaching in blended learning (González 2010; Lameras et al., 2012). In one study, Ellis et al....... In order to identify appropriate uses of blended learning in Higher Education and to enable the tailoring of teaching approaches to the different needs of an increasingly diverse student body, more knowledge is needed on how to integrate blended learning in educational settings and how best to address...... a new strategic focus on 'Educational IT’ with the purpose of strengthening teaching and learning through use of online interactions. Some of the major challenges in the development of this strategy include how to, identify rationales for using blended learning, stimulate pedagogical reflections...

  15. Properties, performance, and applications of biofuel blends: a review

    Directory of Open Access Journals (Sweden)

    Husam Al-Mashhadani

    2017-08-01

    Full Text Available Biofuels such as ethanol and biodiesel derived from living plants or animal matter can be used directly in their neat forms or as blends with their fossil counterparts in internal combustion engines. Although the properties and performance of neat biofuels have been extensively reported, this is not the case for many blends. The purpose of this review is to analyze different forms of biofuel blends that are under research and development comparing their utility and performance in the two primary classes of engines, i.e., spark ignition and compression ignition engines. The fuel properties, performance and emission characteristics, advantages and disadvantages of various fuel blends are compared and discussed. The analysis reveals certain blends possess better overall fuel properties and yield better overall performance than the neat or fossil forms.

  16. Critical Success Factor for Implementing Vocational Blended Learning

    Science.gov (United States)

    Dewi, K. C.; Ciptayani, P. I.; Surjono, H. D.; Priyanto

    2018-01-01

    Blended learning provides many benefits to the flexibility of time, place and situation constraints. The research’s objectives was describing the factors that determine the successful implementation of blended learning in vocational higher education. The research used a qualitative approach, data collected through observations and interviews by questionnare based on the CSFs indicators refers to TAM and Kliger. Data analysis was inductive method. The result provided an illustration that the success of vocational blended learning implementation was largely determined by the selection of instructional models that are inline with learning achievement target. The effectiveness of blended learning required the existence of policy support, readiness of IT infrastructure. Changing lecturer’s culture by utilizing ICT can also encourage the accelerated process of successful implementation. It can concluded that determinant factor of successful implementation of blended learning in vocational education is determined by teacher’s ability in mastering the pedagogical knowledge of designing instructional models.

  17. Positron annihilation lifetime study of interfaces in ternary polymer blends

    International Nuclear Information System (INIS)

    Meghala, D; Ramya, P; Pasang, T; Raj, J M; Ranganathaiah, C; Williams, J F

    2013-01-01

    A new method based on positron lifetime spectroscopy is developed to characterize individual interfaces in ternary polymer blends and hence determine the composition dependent miscibility level. The method owes its origin to the Kirkwood-Risemann-Zimm (KRZ) model for the evaluation of the hydrodynamic interaction parameters (α ij ) which was used successfully for a binary blend with a single interface. The model was revised for the present work for ternary polymer blends to account for three interfaces. The efficacy of this method is shown for two ternary blends namely poly(styrene-co-acrylonitrile)/poly (ethylene-co-vinylacetate)/poly(vinyl chloride) (SAN/EVA/PVC) and polycaprolactone /poly(styrene-co-acrylonitrile)/poly(vinyl chloride) (PCL/SAN/PVC) at different compositions. An effective hydrodynamic interaction parameter, α eff , was introduced to predict the overall miscibility of ternary blends.

  18. Optimization of the octane response of gasoline/ethanol blends

    KAUST Repository

    Badra, Jihad

    2017-07-04

    The octane responses of gasoline/ethanol mixtures are not well understood because of the unidentified intermolecular interactions in such blends. In general, when ethanol is blended with gasoline, the Research Octane Number (RON) and the Motor Octane Number (MON) non-linearly increase or decrease, and the non-linearity is determined by the composition of the base gasoline and the amount of added ethanol. The complexity of commercial gasolines, comprising of hundreds of different components, makes it challenging to understand ethanol-gasoline synergistic/antagonistic blending effects. Understanding ethanol blending effects with simpler gasoline surrogates is critical to acquire knowledge about ethanol blending with complex multi-component gasoline fuels. In this study, the octane numbers (ON) of ethanol blends with five relevant gasoline surrogate molecules were measured. The molecules investigated in this study include: n-pentane, iso-pentane, 1,2,4-trimethylbenzene, cyclopentane and 1-hexene. These new measurements along with the available data of n-heptane, iso-octane, toluene, various primary reference fuels (PRF) and toluene primary reference fuels (TPRF) with ethanol are used to develop a blending rule for the octane response (RON and MON) of multi-component blends with ethanol. In addition, new ON data are collected for six Fuels for Advanced Combustion Engine (FACE) with ethanol. The relatively simple volume based model successfully predicts the octane numbers (ON) of the various ethanol/PRF and ethanol/TPRF blends with the majority of predictions being within the ASTM D2699 (RON) and D2700 (MON) reproducibility limits. The model is also successfully validated against the ON of the FACE gasolines blended with ethanol with the majority of predictions being within the reproducibility limits. Finally, insights into the possible causes of the synergistic and antagonistic effects of different molecules with ethanol are provided.

  19. Optimization of the octane response of gasoline/ethanol blends

    KAUST Repository

    Badra, Jihad; AlRamadan, Abdullah S.; Sarathy, Mani

    2017-01-01

    The octane responses of gasoline/ethanol mixtures are not well understood because of the unidentified intermolecular interactions in such blends. In general, when ethanol is blended with gasoline, the Research Octane Number (RON) and the Motor Octane Number (MON) non-linearly increase or decrease, and the non-linearity is determined by the composition of the base gasoline and the amount of added ethanol. The complexity of commercial gasolines, comprising of hundreds of different components, makes it challenging to understand ethanol-gasoline synergistic/antagonistic blending effects. Understanding ethanol blending effects with simpler gasoline surrogates is critical to acquire knowledge about ethanol blending with complex multi-component gasoline fuels. In this study, the octane numbers (ON) of ethanol blends with five relevant gasoline surrogate molecules were measured. The molecules investigated in this study include: n-pentane, iso-pentane, 1,2,4-trimethylbenzene, cyclopentane and 1-hexene. These new measurements along with the available data of n-heptane, iso-octane, toluene, various primary reference fuels (PRF) and toluene primary reference fuels (TPRF) with ethanol are used to develop a blending rule for the octane response (RON and MON) of multi-component blends with ethanol. In addition, new ON data are collected for six Fuels for Advanced Combustion Engine (FACE) with ethanol. The relatively simple volume based model successfully predicts the octane numbers (ON) of the various ethanol/PRF and ethanol/TPRF blends with the majority of predictions being within the ASTM D2699 (RON) and D2700 (MON) reproducibility limits. The model is also successfully validated against the ON of the FACE gasolines blended with ethanol with the majority of predictions being within the reproducibility limits. Finally, insights into the possible causes of the synergistic and antagonistic effects of different molecules with ethanol are provided.

  20. Blended Learning in Vocational Education: Teachers' Conceptions of Blended Learning and Their Approaches to Teaching and Design

    Science.gov (United States)

    Bliuc, Ana-Maria; Casey, Grant; Bachfischer, Agnieszka; Goodyear, Peter; Ellis, Robert A.

    2012-01-01

    This paper presents research exploring teachers' experiences of using blended learning in vocational education. Teachers involved in designing and teaching using blended learning from a major Australian vocational education provider participated in the study. They received open-ended questionnaires asking to describe their conceptions of blended…

  1. The Literature Landscape of Blended Learning in Higher Education: The Need for Better Understanding of Academic Blended Practice

    Science.gov (United States)

    Torrisi-Steele, Geraldine; Drew, Steve

    2013-01-01

    If we are to realise the potential of blended learning in higher education, then further research into academic practice and relevant academic development is essential. Our review of literature on blended learning in higher education reveals an interesting scholarship landscape which, when described in detail, pointedly directs attention to the…

  2. Coalescence in PLA-PBAT blends under shear flow: Effects of blend preparation and PLA molecular weight

    International Nuclear Information System (INIS)

    Nofar, M.; Heuzey, M. C.; Carreau, P. J.; Kamal, M. R.; Randall, J.

    2016-01-01

    Blends containing 75 wt. % of an amorphous polylactide (PLA) with two different molecular weights and 25 wt. % of a poly[(butylene adipate)-co-terephthalate] (PBAT) were prepared using either a Brabender batch mixer or a twin-screw extruder. These compounds were selected because blending PLA with PBAT can overcome various drawbacks of PLA such as its brittleness and processability limitations. In this study, we investigated the effects of varying the molecular weight of the PLA matrix and of two different mixing processes on the blend morphology and, further, on droplet coalescence during shearing. The rheological properties of these blends were investigated and the interfacial properties were analyzed using the Palierne emulsion model. Droplet coalescence was investigated by applying shear flows of 0.05 and 0.20 s"−"1 at a fixed strain of 60. Subsequently, small amplitude oscillatory shear tests were conducted to investigate changes in the viscoelastic properties. The morphology of the blends was also examined using scanning electron microscope (SEM) micrographs. It was observed that the PBAT droplets were much smaller when twin-screw extrusion was used for the blend preparation. Shearing at 0.05 s"−"1 induced significant droplet coalescence in all blends, but coalescence and changes in the viscoelastic properties were much more pronounced for the PLA-PBAT blend based on a lower molecular weight PLA. The viscoelastic responses were also somehow affected by the thermal degradation of the PLA matrix during the experiments.

  3. Systematic Methodology for Design of Tailor-Made Blended Products: Fuels and Other Blended Products

    DEFF Research Database (Denmark)

    Yunus, Nor Alafiza Binti

    property values are verified by means of rigorous models for the properties and the mixtures. Besides the methodology, as the main contribution, specific supporting tools that were developed to perform each task are also important contributions of this research work. The applicability of the developed...... important in daily life, since they not only keep people moving around, but also guarantee that machines and equipment work smoothly. The objective of this work is to tackle the blending problems using computer-aided tools for the initial stage of the product design. A systematic methodology for design...... methodology and tools was tested through two case studies. In the first case study, two different gasoline blend problems have been solved. In the second case study, four different lubricant design problems have been solved....

  4. Quantification of rice bran oil in oil blends

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, R.; Sharma, H. K.; Sengar, G.

    2012-11-01

    Blends consisting of physically refined rice bran oil (PRBO): sunflower oil (SnF) and PRBO: safflower oil (SAF) in different proportions were analyzed for various physicochemical parameters. The quantification of pure rice bran oil in the blended oils was carried out using different methods including gas chromatographic, HPLC, ultrasonic velocity and methods based on physico-chemical parameters. The physicochemical parameters such as ultrasonic velocity, relative association and acoustic impedance at 2 MHz, iodine value, palmitic acid content and oryzanol content reflected significant changes with increased proportions of PRBO in the blended oils. These parameters were selected as dependent parameters and % PRBO proportion was selected as independent parameters. The study revealed that regression equations based on the oryzanol content, palmitic acid composition, ultrasonic velocity, relative association, acoustic impedance, and iodine value can be used for the quantification of rice bran oil in blended oils. The rice bran oil can easily be quantified in the blended oils based on the oryzanol content by HPLC even at a 1% level. The palmitic acid content in blended oils can also be used as an indicator to quantify rice bran oil at or above the 20% level in blended oils whereas the method based on ultrasonic velocity, acoustic impedance and relative association showed initial promise in the quantification of rice bran oil. (Author) 23 refs.

  5. Blended learning in health education: three case studies.

    Science.gov (United States)

    de Jong, Nynke; Savin-Baden, Maggi; Cunningham, Anne Marie; Verstegen, Daniëlle M L

    2014-09-01

    Blended learning in which online education is combined with face-to-face education is especially useful for (future) health care professionals who need to keep up-to-date. Blended learning can make learning more efficient, for instance by removing barriers of time and distance. In the past distance-based learning activities have often been associated with traditional delivery-based methods, individual learning and limited contact. The central question in this paper is: can blended learning be active and collaborative? Three cases of blended, active and collaborative learning are presented. In case 1 a virtual classroom is used to realize online problem-based learning (PBL). In case 2 PBL cases are presented in Second Life, a 3D immersive virtual world. In case 3 discussion forums, blogs and wikis were used. In all cases face-to-face meetings were also organized. Evaluation results of the three cases clearly show that active, collaborative learning at a distance is possible. Blended learning enables the use of novel instructional methods and student-centred education. The three cases employ different educational methods, thus illustrating diverse possibilities and a variety of learning activities in blended learning. Interaction and communication rules, the role of the teacher, careful selection of collaboration tools and technical preparation should be considered when designing and implementing blended learning.

  6. Blending Biodiesel in Fishing Boat Fuels for Improved Fuel Characteristics

    International Nuclear Information System (INIS)

    Lin, Cherng-Yuan

    2014-01-01

    Biodiesel is a renewable, clean, alternative energy source with advantages, such as excellent lubricity, superior biodegradability, and high combustion efficiency. Biodiesel is considered for mixing with fishing boat fuels to adjust their fuel characteristics so that toxic pollutants and greenhouse-effect gas emissions from such shipping might be reduced. The effects of blending fishing boat fuels A and B with various weight proportions of biodiesel are experimentally investigated in this study. The results show that biodiesel blending can significantly improve the inferior fuel properties of both fishing boat fuels and particularly fuel B. The flash points of both of these fuels increases significantly with the addition of biodiesel and thus enhances the safety of transporting and storing these blended fuels. The flash point of fishing boat fuel B even increases by 16% if 25 wt.% biodiesel is blended. The blending of biodiesel with no sulfur content is found to be one of the most effective ways to reduce the high sulfur content of fishing boat fuel, resulting in a reduction in the emission of sulfur oxides. The addition of only 25 wt.% biodiesel decreased the sulfur content of the fishing boat fuel by 37%. The high kinematic viscosity of fishing boat fuel B was also observed to be reduced by 63% with the blending of just 25 wt.% biodiesel. However, biodiesel blending caused a slight decrease in heating value around 1–4.5%.

  7. A robust quantitative near infrared modeling approach for blend monitoring.

    Science.gov (United States)

    Mohan, Shikhar; Momose, Wataru; Katz, Jeffrey M; Hossain, Md Nayeem; Velez, Natasha; Drennen, James K; Anderson, Carl A

    2018-01-30

    This study demonstrates a material sparing Near-Infrared modeling approach for powder blend monitoring. In this new approach, gram scale powder mixtures are subjected to compression loads to simulate the effect of scale using an Instron universal testing system. Models prepared by the new method development approach (small-scale method) and by a traditional method development (blender-scale method) were compared by simultaneously monitoring a 1kg batch size blend run. Both models demonstrated similar model performance. The small-scale method strategy significantly reduces the total resources expended to develop Near-Infrared calibration models for on-line blend monitoring. Further, this development approach does not require the actual equipment (i.e., blender) to which the method will be applied, only a similar optical interface. Thus, a robust on-line blend monitoring method can be fully developed before any large-scale blending experiment is viable, allowing the blend method to be used during scale-up and blend development trials. Copyright © 2017. Published by Elsevier B.V.

  8. A study of coal-solid waste blend reactivity

    Directory of Open Access Journals (Sweden)

    Nayibe Guerrero

    2008-05-01

    Full Text Available The Flynn-Wall-Ozawa method was used for analysing coal-solid waste blend reactivity in an oxidising atmosphere. The presence of biomass strongly affected coal combustion kinetics when the blend contained more than 30% of it. Activation energy values (evaluated by different blends were 28.7495 kJ/mol for 0% biomass, 31.3915 kJ/mol for 30% biomass, 39.0365 kJ/mol for 50% biomass, 102.431 kJ/mol for 70% biomass and 107.8075 kJ/mol for 100% biomass; these values were close to those reported in the literature. First-order kinetics correlated the data ve-ry well for the 100% coal sample and the blend having 30% biomass and 70% coal. Eighth-order kinetics were more suitable for correlating the experimental data for the 70% biomass-30% coal blend and the 100% biomass sample. Combustion was done without previous pyrolysis of the blends; however segregation of phenomena could be appre-ciated. This seems to indicate that combustion and devolatilisation are independent processes which should be taken into account when building equipment using these kinds of blend.

  9. Blending Biodiesel in Fishing Boat Fuels for Improved Fuel Characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Cherng-Yuan, E-mail: lin7108@ntou.edu.tw [Department of Marine Engineering, National Taiwan Ocean University, Keelung, Taiwan (China)

    2014-02-24

    Biodiesel is a renewable, clean, alternative energy source with advantages, such as excellent lubricity, superior biodegradability, and high combustion efficiency. Biodiesel is considered for mixing with fishing boat fuels to adjust their fuel characteristics so that toxic pollutants and greenhouse-effect gas emissions from such shipping might be reduced. The effects of blending fishing boat fuels A and B with various weight proportions of biodiesel are experimentally investigated in this study. The results show that biodiesel blending can significantly improve the inferior fuel properties of both fishing boat fuels and particularly fuel B. The flash points of both of these fuels increases significantly with the addition of biodiesel and thus enhances the safety of transporting and storing these blended fuels. The flash point of fishing boat fuel B even increases by 16% if 25 wt.% biodiesel is blended. The blending of biodiesel with no sulfur content is found to be one of the most effective ways to reduce the high sulfur content of fishing boat fuel, resulting in a reduction in the emission of sulfur oxides. The addition of only 25 wt.% biodiesel decreased the sulfur content of the fishing boat fuel by 37%. The high kinematic viscosity of fishing boat fuel B was also observed to be reduced by 63% with the blending of just 25 wt.% biodiesel. However, biodiesel blending caused a slight decrease in heating value around 1–4.5%.

  10. Improved Mechanical Properties of Compatibilized Polypropylene/Polyamide-12 Blends

    Directory of Open Access Journals (Sweden)

    Nora Aranburu

    2015-01-01

    Full Text Available Compatibilized blends of polypropylene (PP and polyamide-12 (PA12 as a second component were obtained by direct injection molding having first added 20% maleic anhydride-modified copolymer (PP-g-MA to the PP, which produced partially grafted PP (gPP. A nucleating effect of the PA12 took place on the cooling crystallization of the gPP, and a second crystallization peak of the gPP appeared in the PA12-rich blends, indicating changes in the crystalline morphology. There was a slight drop in the PA12 crystallinity of the compatible blends, whereas the crystallinity of the gPP increased significantly in the PA12-rich blends. The overall reduction in the dispersed phase particle size together with the clear increase in ductility when gPP was used instead of PP proved that compatibilization occurred. Young’s modulus of the blends showed synergistic behavior. This is proposed to be both due to a change in the crystalline morphology of the blends on the one hand and, on the other, in the PA12-rich blends, to the clear increase in the crystallinity of the gPP phase, which may, in turn, have been responsible for the increase in its continuity and its contribution to the modulus.

  11. CURING AND MECHANICAL PROPERTIES OF CHLOROSULPHONATED POLYETHYLENE RUBBER BLEND

    Directory of Open Access Journals (Sweden)

    Jaroslava Budinski-Simendić

    2011-09-01

    Full Text Available In this paper, the curing and mechanical properties of two series of prepared blends, i.e., chlorosulphonated polyethylene (CSM/isobutylene-co-isoprene (IIR rubber blends and chlorosulphonated polyethylene (CSM/chlorinated isobutylene-co-isoprene (CIIR rubber blends were carried out. Blends were prepared using a two-roll mill at a temperature of 40-50 °C. The curing was assessed using a Monsanto oscillating disc rheometer R-100. The process of vulcanization accelerated sulfur of pure rubbers and their blends was carried out in an electrically heated laboratory hydraulic press under a pressure of about 4 MPa and 160 °C. The stress-strain experiments were performed using a tensile tester machine (Zwick 1425. Results indicate that the scorch time, ts2, and optimum cure time, tc90, increase with increasing CSM content in both blends. The value of modulus at 100 and 300% elongation and tensile strength increases with increasing CSM content, whereas elongation at break shows a decreasing trend. The enhancement in mechanical properties was supported by data of crosslink density in these samples obtained from swelling measurement and scanning electron microscopy studies of the rubber blends fractured surfaces

  12. A Study on Students’ Views On Blended Learning Environment

    Directory of Open Access Journals (Sweden)

    Meryem YILMAZ SOYLU

    2006-07-01

    Full Text Available In the 21st century, information and communication technologies (ICT have developed rapidly and influenced most of the fields and education as well. Then, ICT have offered a favorable environment for the development and use of various methods and tools. With the developments in technology, blended learning has gained considerable popularity in recent years. Together with the developments it brought along the description of particular forms of teaching with technology. Blended learning is defined simply as a learning environment that combines technology with face-to-face learning. In other words blended learning means using a variety of delivery methods to best meet the course objectives by combining face-to-face teaching in a traditional classroom with teaching online. This article examines students’ views on blended learning environment. The study was conducted on 64 students from Department of Computer Education and Instructional Technologies in 2005–2006 fall semester in Instructional Design and Authoring Languages in PC Environment at Hacettepe University. The results showed that the students enjoyed taking part in the blended learning environment. Students’ achievement levels and their frequency of participation to forum affected their views about blended learning environment. Face-to-face interaction in blended learning application had the highest score. This result demonstrated the importance of interaction and communication for the success of on-line learning.

  13. Production of silk sericin/silk fibroin blend nanofibers

    Directory of Open Access Journals (Sweden)

    Zhang Xianhua

    2011-01-01

    Full Text Available Abstract Silk sericin (SS/silk fibroin (SF blend nanofibers have been produced by electrospinning in a binary SS/SF trifluoroacetic acid (TFA solution system, which was prepared by mixing 20 wt.% SS TFA solution and 10 wt.% SF TFA solution to give different compositions. The diameters of the SS/SF nanofibers ranged from 33 to 837 nm, and they showed a round cross section. The surface of the SS/SF nanofibers was smooth, and the fibers possessed a bead-free structure. The average diameters of the SS/SF (75/25, 50/50, and 25/75 blend nanofibers were much thicker than that of SS and SF nanofibers. The SS/SF (100/0, 75/25, and 50/50 blend nanofibers were easily dissolved in water, while the SS/SF (25/75 and 0/100 blend nanofibers could not be completely dissolved in water. The SS/SF blend nanofibers could not be completely dissolved in methanol. The SS/SF blend nanofibers were characterized by Fourier transform infrared (FTIR spectroscopy, differential scanning calorimetry, and differential thermal analysis. FTIR showed that the SS/SF blend nanofibers possessed a random coil conformation and ß-sheet structure.

  14. Use of blended learning in workplace learning

    DEFF Research Database (Denmark)

    Georgsen, Marianne; Løvstad, Charlotte Vange

    2014-01-01

    -based teaching materials. This paper presents the experiences of this particular project, and goes on to discuss the following points: • The blended learning design – use of IT for teaching, learning and communication • Digital learning materials – principals of design and use • Work place learning and learning......In 2014, a new system has been put in place for the inspection and approval of social welfare institutions in Denmark. In as little as 10 weeks, 330 new employees in five regional centres participated in an introductory course, designed as work place learning with extensive use of e-learning and IT...... from work – the interplay between experiences of the learner and the curriculum of the program •The approach taken to customising the e-learning design to the needs and demands of a particular case....

  15. Transactional distance in a blended learning environment

    Directory of Open Access Journals (Sweden)

    Jon Dron

    2004-12-01

    Full Text Available This paper presents a case study that describes and discusses the problems encountered during the design and implementation of a blended learning course, largely taught online through a web-based learning environment. Based on Moore's theory of transactional distance, the course was explicitly designed to have dialogue at its heart. However, the reality of systemic behaviours caused by delivering such a course within a group of conventional further and higher educational institutions has led to an entirely unanticipated reversion to structure, with unpleasant consequences for both quality and quantity of dialogue. The paper looks at some of the reasons for this drift, and suggests that some of the disappointing results (in particular in terms of the quality of the students' experience and associated poor retention can be attributed to the lack of dialogue, and consequent increase in transactional distance. It concludes with a description and evaluation of steps currently being taken to correct this behaviour.

  16. Quantum and gravity. Blend or melange?

    Energy Technology Data Exchange (ETDEWEB)

    Wuethrich, Christian [University of Geneva (Switzerland)

    2016-07-01

    Do we need to quantize gravity, as it is tacitly assumed in much of fundamental physics? The standard lore falls short of justifying an affirmative answer. Black hole thermodynamics is widely considered, faint though it may be, our firmest hint at a quantum theory of gravity - despite the failure to date to observe Hawking radiation or any other effect that would require going beyond a classical description of black holes. Hawking radiation hitherto merely enjoys a theoretical derivation in a semi-classical theory combining quantum matter with classical gravity. But how can a semi-classical melange of physical principles possibly justify that the quantum and gravity are blended into a unified fundamental theory when the latter is generally expected to reject at least some of the principles in the former?.

  17. INOVASI PEMBELAJARAN AKUNTANSI BERBASIS BLENDED LEARNING

    Directory of Open Access Journals (Sweden)

    Lyna Latifah

    2016-02-01

    Full Text Available the accounting lectures have a big challengeb to improve the quality of graduates who are expected to have high knowledge and skill, to have good critical analysis and decision making. Thus: accounting lecturers are needed to improve their teaching and learning processes especially on learning design and assessment. Improving students knowledge and skill in accounting field can be created by using learning philosophy which makes students active and integrative in the class room. this articles discusses about the innovation of accounting learning with blended learning which collaborates cooperative learning and e-learning. Cooperative learning is a learning approach which emphasizes on structured behavior to cooperate in groups it can improve students interpersonal skill, cooperation, critical analysis and decision making. On the other hand, the application of cooperative learning needs more time so it can be solved by using computer with e-learning.

  18. Synthesis of geopolymer from biomass-coal ash blends

    Science.gov (United States)

    Samadhi, Tjokorde Walmiki; Wulandari, Winny; Prasetyo, Muhammad Iqbal; Fernando, Muhammad Rizki; Purbasari, Aprilina

    2017-09-01

    Geopolymer is an environmentally attractive Portland cement substitute, owing to its lower carbon footprint and its ability to consume various aluminosilicate waste materials as its precursors. This work describes the development of geopolymer formulation based on biomass-coal ash blends, which is predicted to be the prevalent type of waste when biomass-based thermal energy production becomes mainstream in Indonesia. The ash blends contain an ASTM Class F coal fly ash (FA), rice husk ash (RHA), and coconut shell ash (CSA). A mixture of Na2SiO3 and concentrated KOH is used as the activator solution. A preliminary experiment identified the appropriate activator/ash mass ratio to be 2.0, while the activator Na2SiO3/KOH ratio varies from 0.8 to 2.0 with increasing ash blend Si/Al ratio. Both non-blended FA and CSA are able to produce geopolymer mortars with 7-day compressive strength exceeding the Indonesian national SNI 15-2049-2004 standard minimum value of 2.0 MPa stipulated for Portland cement mortars. Ash blends have to be formulated with a maximum RHA content of approximately 50 %-mass to yield satisfactory 7-day strength. No optimum ash blend composition is identified within the simplex ternary ash blend compositional region. The strength decreases with Si/Al ratio of the ash blends due to increasing amount of unreacted silicate raw materials at the end of the geopolymer hardening period. Overall, it is confirmed that CSA and blended RHA are feasible raw materials for geopolymer production..

  19. Blended learning in ethics education: a survey of nursing students.

    Science.gov (United States)

    Hsu, Li-Ling

    2011-05-01

    Nurses are experiencing new ethical issues as a result of global developments and changes in health care. With health care becoming increasingly sophisticated, and countries facing challenges of graying population, ethical issues involved in health care are bound to expand in quantity and in depth. Blended learning rather as a combination of multiple delivery media designed to promote meaningful learning. Specifically, this study was focused on two questions: (1) the students' satisfaction and attitudes as members of a scenario-based learning process in a blended learning environment; (2) the relationship between students' satisfaction ratings of nursing ethics course and their attitudes in the blended learning environment. In total, 99 senior undergraduate nursing students currently studying at a public nursing college in Taiwan were invited to participate in this study. A cross-sectional survey design was adopted in this study. The participants were asked to fill out two Likert-scale questionnaire surveys: CAAS (Case Analysis Attitude Scale), and BLSS (Blended Learning Satisfaction Scale). The results showed what students felt about their blended learning experiences - mostly items ranged from 3.27-3.76 (the highest score is 5). Another self-assessment of scenario analysis instrument revealed the mean scores ranged from 2.87-4.19. Nearly 57.8% of the participants rated the course 'extremely helpful' or 'very helpful.' This study showed statistically significant correlations (r=0.43) between students' satisfaction with blended learning and case analysis attitudes. In addition, results testified to a potential of the blended learning model proposed in this study to bridge the gap between students and instructors and the one between students and their peers, which are typical of blended learning, and to create meaningful learning by employing blended pedagogical consideration in the course design. The use of scenario instruction enables students to develop critical

  20. COOLING COIL EFFECTS ON BLENDING IN A PILOT SCALE TANK

    International Nuclear Information System (INIS)

    Leishear, R.; Poirier, M.; Fowley, M.; Steeper, T.

    2010-01-01

    Blending, or mixing, processes in 1.3 million gallon nuclear waste tanks are complicated by the fact that miles of serpentine, vertical, cooling coils are installed in the tanks. As a step toward investigating blending interference due to coils in this type of tank, a 1/10.85 scale tank and pump model were constructed for pilot scale testing. A series of tests were performed in this scaled tank by adding blue dye to visualize blending, and by adding acid or base tracers to solution to quantify the time required to effectively blend the tank contents. The acid and base tests were monitored with pH probes, which were located in the pilot scale tank to ensure that representative samples were obtained. Using the probes, the hydronium ion concentration [H + ] was measured to ensure that a uniform concentration was obtained throughout the tank. As a result of pilot scale testing, a significantly improved understanding of mixing, or blending, in nuclear waste tanks has been achieved. Evaluation of test data showed that cooling coils in the waste tank model increased pilot scale blending times by 200% in the recommended operating range, compared to previous theoretical estimates of a 10-50% increase. Below the planned operating range, pilot scale blending times were increased by as much as 700% in a tank with coils installed. One pump, rather than two or more, was shown to effectively blend the tank contents, and dual pump nozzles installed parallel to the tank wall were shown to provide optimal blending. In short, experimental results varied significantly from expectations.

  1. A systematic methodology for design of tailor-made blended products

    DEFF Research Database (Denmark)

    Yunus, Nor Alafiza Binti; Gernaey, Krist; Woodley, John

    2014-01-01

    A systematic methodology for design of tailor-made blended products has been developed. In tailor-made blended products, one identifies the product needs and matches them by blending different chemicals. The systematic methodology has four main tasks. First, the design problem is defined: the pro......, the methodology is highlighted through two case studies involving gasoline blends and lubricant base oils....

  2. Handbook for Handling, Storing, and Dispensing E85 and Other Ethanol-Gasoline Blends

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-03-02

    This document provides information on ethanol fuel properties, standards, codes, best practices, and equipment information for those who blend, distribute, store, sell, or use E15 (gasoline blended with 10.5 percent - 15 percent ethanol), E85 (marketing term for ethanol-gasoline blends containing 51 percent - 83 percent ethanol, depending on geography and season), and other ethanol blends.

  3. Handbook for Handling, Storing, and Dispensing E85 and Other Ethanol-Gasoline Blends

    Energy Technology Data Exchange (ETDEWEB)

    2016-03-01

    This document provides information on ethanol fuel properties, standards, codes, best practices, and equipment information for those who blend, distribute, store, sell, or use E15 (gasoline blended with 10.5 percent - 15 percent ethanol), E85 (marketing term for ethanol-gasoline blends containing 51 percent - 83 percent ethanol, depending on geography and season), and other ethanol blends.

  4. Optimal set of selected uranium enrichments that minimizes blending consequences

    International Nuclear Information System (INIS)

    Nachlas, J.A.; Kurstedt, H.A. Jr.; Lobber, J.S. Jr.

    1977-01-01

    Identities, quantities, and costs associated with producing a set of selected enrichments and blending them to provide fuel for existing reactors are investigated using an optimization model constructed with appropriate constraints. Selected enrichments are required for either nuclear reactor fuel standardization or potential uranium enrichment alternatives such as the gas centrifuge. Using a mixed-integer linear program, the model minimizes present worth costs for a 39-product-enrichment reference case. For four ingredients, the marginal blending cost is only 0.18% of the total direct production cost. Natural uranium is not an optimal blending ingredient. Optimal values reappear in most sets of ingredient enrichments

  5. Blended e-learning Design: Discussion of Cultural Issues

    Directory of Open Access Journals (Sweden)

    Ahmed A Al-Hunaiyyan

    2008-06-01

    Full Text Available Blended e-learning is becoming an educational issue especially with the new development of e-learning technology and globalization. Educators as the question: can we design these systems to accommodate different cultural groups and various learning strategies. This paper addresses some design issues when selecting a blended e-learning approach; it discusses some cultural elements that affect the design of blended e-learning. The paper also explores issues related to learning design, then emphasizes on the importance of cultural learning objects (CLO and its role in the design of multimedia-based e-learning systems.

  6. Critical crossover phenomena in compatible polymer blends studied with SANS

    DEFF Research Database (Denmark)

    Schwahn, D.; Janssen, S.; Willner, L.

    1995-01-01

    Polymer blends show a much larger 3d-Ising regime, e.g. a much larger Ginzburg number Gi than predicted by the Ginzburg criterion. This discrepancy is supposed to be explained by the compressibility or the free volume of the blend. In this paper we present and discuss the Gi number of polymer...... on monomeric microstructure and on pressure. This clearly shows that Gi is not a universal function. The observed strong decrease of Gi with pressure is a clear experimental proof that the critical crossover behaviour in polymer blends is indeed strongly influenced by the compressibility or free volume...

  7. River Protection Project Mission Analysis Waste Blending Study

    International Nuclear Information System (INIS)

    Shuford, D.H.; Stegen, G.

    2010-01-01

    Preliminary evaluation for blending Hanford site waste with the objective of minimizing the amount of high-level waste (HLW) glass volumes without major changes to the overall waste retrieval and processing sequences currently planned. The evaluation utilizes simplified spreadsheet models developed to allow screening type comparisons of blending options without the need to use the Hanford Tank Waste Operations Simulator (HTWOS) model. The blending scenarios evaluated are expected to increase tank farm operation costs due to increased waste transfers. Benefit would be derived from shorter operating time period for tank waste processing facilities, reduced onsite storage of immobilized HLW, and reduced offsite transportation and disposal costs for the immobilized HLW.

  8. Exciton and Hole-Transfer Dynamics in Polymer: Fullerene Blends

    Directory of Open Access Journals (Sweden)

    van Loosdrecht P. H. M.

    2013-03-01

    Full Text Available Ultrafast hole transfer dynamics from fullerene derivative to polymer in bulk heterojunction blends are studied with visible-pump - IR-probe spectroscopy. The hole transfer process is found to occur in 50/300 fs next to the interface, while a longer 15-ps time is attributed to exciton diffusion towards interface in PC71BM domains. High polaron generation efficiency in P3HT blends indicates excellent intercalation between the polymer and the fullerene even at highest PC71BM concentration thereby yielding a valuable information on the blend morphology.

  9. Phosphor blends for high-CRI fluorescent lamps

    Science.gov (United States)

    Setlur, Anant Achyut [Niskayuna, NY; Srivastava, Alok Mani [Niskayuna, NY; Comanzo, Holly Ann [Niskayuna, NY; Manivannan, Venkatesan [Clifton Park, NY; Beers, William Winder [Chesterland, OH; Toth, Katalin [Pomaz, HU; Balazs, Laszlo D [Budapest, HU

    2008-06-24

    A phosphor blend comprises at least two phosphors each selected from one of the groups of phosphors that absorb UV electromagnetic radiation and emit in a region of visible light. The phosphor blend can be applied to a discharge gas radiation source to produce light sources having high color rendering index. A phosphor blend is advantageously includes the phosphor (Tb,Y,LuLa,Gd).sub.x(Al,Ga).sub.yO.sub.12:Ce.sup.3+, wherein x is in the range from about 2.8 to and including 3 and y is in the range from about 4 to and including 5.

  10. Canada's directory of ethanol-blended fuel retailers (December 1998)

    International Nuclear Information System (INIS)

    1998-12-01

    This publication serves as a directory of ethanol-blended gasoline retailers in Quebec, Ontario, Manitoba, Saskatchewan, Alberta, British Columbia, and the Yukon. The listings include the name and address of the retailer. The listing is organized by province and cities, beginning with the Yukon in the west and proceeding east to Quebec. A list of bulk purchase facilities of ethanol-blended fuels is also included. As of December 1998, there were a total of 929 retail outlets for ethanol blended gasoline in Canada

  11. Controlling the Solidification of Organic Photovoltaic Blends with Nucleating Agents

    KAUST Repository

    Nekuda Malik, Jennifer A.

    2014-11-20

    Blending fullerenes with a donor polymer for the fabrication of organic solar cells often leads to at least partial vitrification of one, if not both, components. For prototypical poly(3-hexylthiophene):fullerene blend, we show that the addition of a commercial nucleating agent, di(3,4-dimethyl benzylidene)sorbitol, to such binary blends accelerates the crystallization of the donor, resulting in an increase in its degree of crystallinity in as-cast structures. This allows manipulation of the extent of intermixing/ phase separation of the donor and acceptor directly from solution, offering a tool to improve device characteristics such as power conversion efficiency.

  12. Controlling the Solidification of Organic Photovoltaic Blends with Nucleating Agents

    KAUST Repository

    Nekuda Malik, Jennifer A.; Treat, Neil D.; Abdelsamie, Maged; Yu, Liyang; Li, Ruipeng; Smilgies, Detlef-M.; Amassian, Aram; Hawker, Craig J.; Chabinyc, Michael L.; Stingelin, Natalie

    2014-01-01

    Blending fullerenes with a donor polymer for the fabrication of organic solar cells often leads to at least partial vitrification of one, if not both, components. For prototypical poly(3-hexylthiophene):fullerene blend, we show that the addition of a commercial nucleating agent, di(3,4-dimethyl benzylidene)sorbitol, to such binary blends accelerates the crystallization of the donor, resulting in an increase in its degree of crystallinity in as-cast structures. This allows manipulation of the extent of intermixing/ phase separation of the donor and acceptor directly from solution, offering a tool to improve device characteristics such as power conversion efficiency.

  13. Generator Set Durability Testing Using 25% ATJ Fuel Blend

    Science.gov (United States)

    2016-02-01

    UNCLASSIFIED UNCLASSIFIED 3 Table 1. Chemical & Physical Properties of Evaluated 25% ATJ Blend Test ASTM Method Units SwRI Sample ID...25% ATJ Blend Test ASTM Method Units SwRI Sample ID CL15-8613 Results Min Max Flash Point D93 °C 56.5 38 Density D4052 Test...Chemical & Physical Properties of Evaluated 25% ATJ Blend Test ASTM Method Units SwRI Sample ID CL15-8613 Results Min Max Fuel System Icing Inhibitor

  14. Preparation and Characterization of Keratin/Alginate Blend Microparticles

    OpenAIRE

    Srisuwan, Yaowalak; Srihanam, Prasong

    2018-01-01

    The water-in-oil (W/O) emulsification-diffusion method was used for construction of keratin (Ker), alginate (Alg), and Ker/Alg blend microparticles. The Ker, Alg, and Ker/Alg blend solutions were used as the water phase, while ethyl acetate was used as the oil phase. Firstly, different concentrations of Ker solution was used to find suitable content. 1.6% w/v Ker solution was blended with the same concentration of the Alg solution for further microparticle construction. Results from scanning ...

  15. Analytical characterization of pure and blended watermelon (citrullus lanatus) oil: impact of blending on oxidative stability

    International Nuclear Information System (INIS)

    Azeem, M.W.; Nadeem, M.

    2015-01-01

    Analytical characterization of pure, blended watermelon (Citrulluslanatus) oil and impact of blending on oxidative stability was investigated. Watermelon oil was added with mango (Mangiferaindica L.) kernel oil at four different concentrations 5, 10, 15 and 20% (B 1, B2, B3 and B4) and referenced with a control (100% watermelon oil). All the blends were stored in transparent PET bottles at ambient temperature (25-28 degree C) for 3 months; storage stability was assessed at the interval of 1 month. Free fatty acid, unsaponifiable matter, saponification value, refractive index and iodine value of watermelon seed oil and mango kernel oil was 1.38%, 0.34%; 0.71%, 1.68%; 198, 193; 1.468, 1.457; 107.51, 54.62, respectively. The tocopherol content of watermelon oil, mango kernel oil, B1, B2, B3 and B4 was 127.49, 205.44, 135.24, 144.52, 156.81 and 169.34 mg/kg. delta tocopherol in watermelon oil, mango kernel oil, B1, B2, B3 and B4 was 55.26, 34.81, 53.64, 51.27, 50.14 and 48.23 mg/kg. Concentration of linoleic acid decreased from 50.78% to 30.17% when 40% mango kernel oil was added to watermelon oil. Oleic acid increased from 22.89% in watermelon oil to 25.19%, 28.84% and 30.64% in B1, B2, B3 and B4. The increase in peroxide value of watermelon oil, B1, B2, B3 and B4 was 10.07, 9.56, 7.62, 5.17 and 2.87 (meqO/sub 2//kg) in a time dependent manner. Induction period of pure watermelon oil was less than mango kernel oil and blends. These results suggest that chemical characteristics and oxidative stability of pure watermelon oil can be improved by blending with mango kernel oil. (author)

  16. Analytical Characterization of Pure and Blended Watermelon (Citrullus lanatus oil: Impact of Blending on Oxidative Stability

    Directory of Open Access Journals (Sweden)

    Muhammad Waqar Azeem

    2015-06-01

    Full Text Available Analytical characterization of pure, blended watermelon (Citrulluslanatus oil and impact of blending on oxidative stability was investigated. Watermelon oil was added with mango (Mangiferaindica L. kernel oil at four different concentrations 5, 10, 15 and 20% (B1, B2, B3 and B4 and referenced with a control (100% watermelon oil. All the blends were stored in transparent PET bottles at ambient temperature (25-28oC for 3 months; storage stability was assessed at the interval of 1 month. Free fatty acid, unsaponifiable matter, saponification value, refractive index and iodine value of watermelon seed oil and mango kernel oil was 1.38%, 0.34%; 0.71%, 1.68%; 198, 193; 1.468, 1.457; 107.51, 54.62, respectively. The α tocopherol content of watermelon oil, mango kernel oil, B1, B2, B3 and B4 was 127.49, 205.44, 135.24, 144.52, 156.81 and 169.34 mg/kg. δ tocopherol in watermelon oil, mango kernel oil, B1, B2, B3 and B4 was 55.26, 34.81, 53.64, 51.27, 50.14 and 48.23 mg/kg. Concentration of linoleic acid decreased from 50.78% to 30.17% when 40% mango kernel oil was added to watermelon oil. Oleic acid increased from 22.89% in watermelon oil to 25.19%, 28.84% and 30.64% in B1, B2, B3 and B4. The increase in peroxide value of watermelon oil, B1, B2, B3 and B4 was 10.07, 9.56, 7.62, 5.17 and 2.87 (meqO2/kg in a time dependent manner. Induction period of pure watermelon oil was less than mango kernel oil and blends. These results suggest that chemical characteristics and oxidative stability of pure watermelon oil can be improved by blending with mango kernel oil.

  17. Effects of Blended-Cement Paste Chemical Composition Changes on Some Strength Gains of Blended-Mortars

    Science.gov (United States)

    Kirgiz, Mehmet Serkan

    2014-01-01

    Effects of chemical compositions changes of blended-cement pastes (BCPCCC) on some strength gains of blended cement mortars (BCMSG) were monitored in order to gain a better understanding for developments of hydration and strength of blended cements. Blended cements (BC) were prepared by blending of 5% gypsum and 6%, 20%, 21%, and 35% marble powder (MP) or 6%, 20%, 21%, and 35% brick powder (BP) for CEMI42.5N cement clinker and grinding these portions in ball mill at 30 (min). Pastes and mortars, containing the MP-BC and the BP-BC and the reference cement (RC) and tap water and standard mortar sand, were also mixed and they were cured within water until testing. Experiments included chemical compositions of pastes and compressive strengths (CS) and flexural strengths (FS) of mortars were determined at 7th-day, 28th-day, and 90th-day according to TS EN 196-2 and TS EN 196-1 present standards. Experimental results indicated that ups and downs of silica oxide (SiO2), sodium oxide (Na2O), and alkali at MP-BCPCC and continuously rising movement of silica oxide (SiO2) at BP-BCPCC positively influenced CS and FS of blended cement mortars (BCM) in comparison with reference mortars (RM) at whole cure days as MP up to 6% or BP up to 35% was blended for cement. PMID:24587737

  18. Effects of Blended-Cement Paste Chemical Composition Changes on Some Strength Gains of Blended-Mortars

    Directory of Open Access Journals (Sweden)

    Mehmet Serkan Kirgiz

    2014-01-01

    Full Text Available Effects of chemical compositions changes of blended-cement pastes (BCPCCC on some strength gains of blended cement mortars (BCMSG were monitored in order to gain a better understanding for developments of hydration and strength of blended cements. Blended cements (BC were prepared by blending of 5% gypsum and 6%, 20%, 21%, and 35% marble powder (MP or 6%, 20%, 21%, and 35% brick powder (BP for CEMI42.5N cement clinker and grinding these portions in ball mill at 30 (min. Pastes and mortars, containing the MP-BC and the BP-BC and the reference cement (RC and tap water and standard mortar sand, were also mixed and they were cured within water until testing. Experiments included chemical compositions of pastes and compressive strengths (CS and flexural strengths (FS of mortars were determined at 7th-day, 28th-day, and 90th-day according to TS EN 196-2 and TS EN 196-1 present standards. Experimental results indicated that ups and downs of silica oxide (SiO2, sodium oxide (Na2O, and alkali at MP-BCPCC and continuously rising movement of silica oxide (SiO2 at BP-BCPCC positively influenced CS and FS of blended cement mortars (BCM in comparison with reference mortars (RM at whole cure days as MP up to 6% or BP up to 35% was blended for cement.

  19. The lure of global branding.

    Science.gov (United States)

    Aaker, D A; Joachimsthaler, E

    1999-01-01

    As more and more companies begin to see the world as their market, brand builders look with envy upon those businesses that appear to have created global brands--brands whose positioning, advertising strategy, personality, look, and feel are in most respects the same from one country to another. Attracted by such high-profile examples of success, these companies want to globalize their own brands. But that's a risky path to follow, according to David Aaker and Erich Joachimsthaler. Why? Because creating strong global brands takes global brand leadership. It can't be done simply by edict from on high. Specifically, companies must use organizational structures, processes, and cultures to allocate brand-building resources globally, to create global synergies, and to develop a global brand strategy that coordinates and leverages country brand strategies. Aaker and Joachimsthaler offer four prescriptions for companies seeking to achieve global brand leadership. First, companies must stimulate the sharing of insights and best practices across countries--a system in which "it won't work here" attitudes can be overcome. Second, companies should support a common global brand-planning process, one that is consistent across markets and products. Third, they should assign global managerial responsibility for brands in order to create cross-country synergies and to fight local bias. And fourth, they need to execute brilliant brand-building strategies. Before stampeding blindly toward global branding, companies need to think through the systems they have in place. Otherwise, any success they achieve is likely to be random--and that's a fail-safe recipe for mediocrity.

  20. The Lure of Wireless Encryption

    CERN Multimedia

    Computer Security Team

    2013-01-01

    Following our article entitled “Jekyll or Hyde? Better browse securely” in the last issue of the Bulletin, some people wondered why the CERN wireless network is not encrypted…   There are many arguments why it is not. The simplest is usability: the communication and management of the corresponding access keys would be challenging given the sheer number of wireless devices the CERN network hosts. Keys would quickly become public, e.g. at conferences, and might be shared, written on whiteboards, etc. Then there are all the devices which cannot be easily configured to use encryption protocols - a fact which would create plenty of calls to the CERN Service Desk… But our main argument is that wireless encryption is DECEPTIVE. Wireless encryption is deceptive as it only protects the wireless network against unauthorised access (and the CERN network already has other means to protect against that). Wireless encryption however, does not really help you. You ...

  1. Conversion and Blending Facility highly enriched uranium to low enriched uranium as metal. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-05

    The mission of this Conversion and Blending Facility (CBF) will be to blend surplus HEU metal and alloy with depleted uranium metal to produce an LEU product. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal.

  2. A Novel Approach for Automatic Machining Feature Recognition with Edge Blend Feature

    OpenAIRE

    Keong Chen Wong; Yusof Yusri

    2017-01-01

    This paper presents an algorithm for efficiently recognizing and determining the convexity of an edge blend feature. The algorithm first recognizes all of the edge blend features from the Boundary Representation of a part; then a series of convexity test have been run on the recognized edge blend features. The novelty of the presented algorithm lies in, instead of each recognized blend feature is suppressed as most of researchers did, the recognized blend features of this research are gone th...

  3. Conversion and Blending Facility highly enriched uranium to low enriched uranium as metal. Revision 1

    International Nuclear Information System (INIS)

    1995-01-01

    The mission of this Conversion and Blending Facility (CBF) will be to blend surplus HEU metal and alloy with depleted uranium metal to produce an LEU product. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal

  4. Stability of traditionally processed vegetable oils and their blends ...

    African Journals Online (AJOL)

    physicochemical properties which included acid value, saponification value, peroxide value, iodine ... The oils and their blends were stored in two different conditions; one batch at the air-tight .... about 0.5 ml of starch indicator solution was.

  5. Enhancing the blended learning experience of Calculus I students

    Directory of Open Access Journals (Sweden)

    A. Al-Ghassani

    2015-08-01

    Full Text Available Blended Learning showed in the last two decades to be one of the effective ways in education and training. We illustrate our initiative experience with blended learning in the course Calculus I. The main goals we want to achieve are improving students understanding of the course concepts, increasing the level of uniformity in this multi-sections course and enhancing students blended learning experience online and offline. Consequently, this affects positively students' academic performance. We describe and discuss the results that we achieved and the challenges we encountered in view of the initiative aims and goals. The blended learning delivery methods were through Learning Management System (LMS as the online medium and through new offline activities inside and outside the classroom. The LMS we used is Moodle. We designed the resources and activities to cater for the learners different needs. The offline activities were chosen and designed to strengthen the weakness in students study skills based in our experience.

  6. Modeling terminal ballistics using blending-type spline surfaces

    Science.gov (United States)

    Pedersen, Aleksander; Bratlie, Jostein; Dalmo, Rune

    2014-12-01

    We explore using GERBS, a blending-type spline construction, to represent deform able thin-plates and model terminal ballistics. Strategies to construct geometry for different scenarios of terminal ballistics are proposed.

  7. Lifecycle optimized ethanol-gasoline blends for turbocharged engines

    KAUST Repository

    Zhang, Bo; Sarathy, Mani

    2016-01-01

    This study presents a lifecycle (well-to-wheel) analysis to determine the CO2 emissions associated with ethanol blended gasoline in optimized turbocharged engines. This study provides a more accurate assessment on the best-achievable CO2 emission

  8. Influence of compatibilizer on blends degradation during processing

    Directory of Open Access Journals (Sweden)

    Walter R. Waldman

    2013-01-01

    Full Text Available The thermomechanical degradation of blends made from polypropylene and polystyrene, with or without compatibilizer, was studied using an internal mixer coupled to a torque rheometer. The blends processed without compatibilizer presented regular and expected results regarding torque reduction, with evidence of chain scission. The blends processed with the block copolymer of styrene and butadiene, SBS, as a compatibilizer presented unchanged or less reduced variation on torque values during processing. The extraction of stabilizers from the compatibilizer before processing did not affect the results. The compatibilizer concentration in the blends was varied, with its influence still being observed in concentrations as low as 0.03 parts per hundred. Similar results were obtained in an experiment comparing the performance of a primary commercial anti-oxidant, Irganox 1076, and the compatibilizer SBS. Therefore, the compatibilizer can be considered as a processing aid agent with positive influence on avoiding thermomechanical degradation.

  9. An exploration of students' experiences of Blended Learning in a ...

    African Journals Online (AJOL)

    ... experiences of Blended Learning through their interaction with the adaptive ... to university resources such as computers and Wi-Fi had a greater chance of ... were discordant - students scored better on online tests than in written tests.

  10. Blends of caprolactam/caprolactone copolymers and chlorinated polymers

    NARCIS (Netherlands)

    Alberda van Ekenstein, G.O.R.; Deuring, H.; ten Brinke, G.; Ellis, T.S.

    The phase behaviour of blends of chlorinated polyethylene, polyvinyl chloride (PVC) and chlorinated PVC with random copolymers of caprolactone and caprolactam has been investigated and the results correlated with a binary interaction model. The known miscibility of polycaprolactone in the

  11. Fuel properties of loofah (Luffa cylindrica L.) biofuel blended with ...

    African Journals Online (AJOL)

    ajl6

    Fuel properties of loofah oil and its ethyl ester blended with diesel were experimentally determined. ... The escalating prices of petroleum fuels, the .... equation developed by Bamgboye and Hansen (2008) was used to ..... Renewable Energy.

  12. Biodegradation of biodiesel/diesel blends by Candida viswanathii

    African Journals Online (AJOL)

    USER

    2009-06-17

    diesel blends and neat biodiesel since it preferable ... alkanes and aromatic compounds obtained from the ... technique based on the action of microorganisms, which turn hazardous contaminants into non toxic substances.

  13. Photonic polymer-blend structures and method for making

    Science.gov (United States)

    Barnes, Michael D.

    2004-06-29

    The present invention comprises the formation of photonic polymer-blend structures having tunable optical and mechanical properties. The photonic polymer-blend structures comprise monomer units of spherical microparticles of a polymer-blend material wherein the spherical microparticles have surfaces partially merged with one another in a robust inter-particle bond having a tunable inter-particle separation or bond length sequentially attached in a desired and programmable architecture. The photonic polymer-blend structures of the present invention can be linked by several hundred individual particles sequentially linked to form complex three-dimensional structures or highly ordered two-dimensional arrays of 3D columns with 2D spacing.

  14. Blending the most fundamental Remote-Sensing principles (RS ...

    African Journals Online (AJOL)

    Blending the most fundamental Remote-Sensing principles (RS) with the most functional spatial knowledge (GIS) with the objective of the determination of the accident-prone palms and points (case study: Tehran-Hamadan Highway on Saveh Superhighway)

  15. AstroBlend: Visualization package for use with Blender

    Science.gov (United States)

    Naiman, J. P.

    2015-12-01

    AstroBlend is a visualization package for use in the three dimensional animation and modeling software, Blender. It reads data in via a text file or can use pre-fab isosurface files stored as OBJ or Wavefront files. AstroBlend supports a variety of codes such as FLASH (ascl:1010.082), Enzo (ascl:1010.072), and Athena (ascl:1010.014), and combines artistic 3D models with computational astrophysics datasets to create models and animations.

  16. STUDY ON THE GENERATION OF SOME BLENDING SURFACES

    Directory of Open Access Journals (Sweden)

    Drăgan Florin

    2009-07-01

    Full Text Available In this paper, using the blending (Coons method, we generate some families of free-form surfaces feasible in civil engineering, industries of airplanes, ships, automobiles, industrial and artistic objects, scientific researches and others. The possibility of designing free-form surfaces with the aid of computers has led to new methods for defining surfaces of the following types: Bezier [3], spline [3], Shepard [13], blending (Coons and Gordon [8], [3] and others.

  17. THE HANDBOOK OF BLENDED LEARNING:Global Perspectives, Local Designs

    OpenAIRE

    Reviewed by Alev ATES

    2009-01-01

    THE HANDBOOK OF BLENDED LEARNING:Global Perspectives, Local Designs Curtis J. Bonk (ed.) and Charles R. Graham (ed.), Jay Cross (Foreword),Micheal G. Moore Foreword) ISBN: 978-0-7879-7758-0 Publisher: John Wiley & Sons, Inc. Pfeiffer Pages: 624 March 2006.Reviewed by Alev ATESPhD Student at Curriculum and Instruction,Lecturer at Computer Education and Instructional Technologies,Faculty of Education, Ege University, Izmir, TURKEYBlended learning or blended e-learning sounds like aconfusing ter...

  18. Becoming Blended. A Case Study in Teacher Identity

    OpenAIRE

    Rentería, Victoria

    2014-01-01

    This case-study explores the identities of two teachers in the English Blended Program of a Mexican University during a four month period. The aim is to discover how agency creates different kinds of impacts on teacher's identity in the context of a blended program. Through an interpretive and sociocultural perspective an analysis was conducted by examining data gathered from face-to-face class observations, teacher's Moodle pages, teacher's journals and interviews, as well as questionnaires ...

  19. Lifecycle optimized ethanol-gasoline blends for turbocharged engines

    KAUST Repository

    Zhang, Bo

    2016-08-16

    This study presents a lifecycle (well-to-wheel) analysis to determine the CO2 emissions associated with ethanol blended gasoline in optimized turbocharged engines. This study provides a more accurate assessment on the best-achievable CO2 emission of ethanol blended gasoline mixtures in future engines. The optimal fuel blend (lowest CO2 emitting fuel) is identified. A range of gasoline fuels is studied, containing different ethanol volume percentages (E0–E40), research octane numbers (RON, 92–105), and octane sensitivities (8.5–15.5). Sugarcane-based and cellulosic ethanol-blended gasolines are shown to be effective in reducing lifecycle CO2 emission, while corn-based ethanol is not as effective. A refinery simulation of production emission was utilized, and combined with vehicle fuel consumption modeling to determine the lifecycle CO2 emissions associated with ethanol-blended gasoline in turbocharged engines. The critical parameters studied, and related to blended fuel lifecycle CO2 emissions, are ethanol content, research octane number, and octane sensitivity. The lowest-emitting blended fuel had an ethanol content of 32 vol%, RON of 105, and octane sensitivity of 15.5; resulting in a CO2 reduction of 7.1%, compared to the reference gasoline fuel and engine technology. The advantage of ethanol addition is greatest on a per unit basis at low concentrations. Finally, this study shows that engine-downsizing technology can yield an additional CO2 reduction of up to 25.5% in a two-stage downsized turbocharged engine burning the optimum sugarcane-based fuel blend. The social cost savings in the USA, from the CO2 reduction, is estimated to be as much as $187 billion/year. © 2016 Elsevier Ltd

  20. Novel bio-based and biodegradable polymer blends

    Science.gov (United States)

    Yang, Shengzhe

    Most plastic materials, including high performance thermoplastics and thermosets are produced entirely from petroleum-based products. The volatility of the natural oil markets and the increasing cost of petroleum have led to a push to reduce the dependence on petroleum products. Together with an increase in environmental awareness, this has promoted the use of alternative, biorenewable, environmentally-friendly products, such as biomass. The growing interest in replacing petroleum-based products by inexpensive, renewable, natural materials is important for sustainable development into the future and will have a significant impact on the polymer industry and the environment. This thesis involved characterization and development of two series of novel bio-based polymer blends, namely polyhydroxyalkanoate (PHA)/polyamide (PA) and poly(lactic acid) (PLA)/soy protein. Blends with different concentrations and compatible microstructures were prepared using twin-screw extruder. For PHA/PA blends, the poor mechanical properties of PHA improved significantly with an excellent combination of strength, stiffness and toughness by adding PA. Furthermore, the effect of blending on the viscoelastic properties has been investigated using small-amplitude oscillatory shear flow experiments as a function of blend composition and angular frequency. The elastic shear modulus (G‧) and complex viscosity of the blends increased significantly with increasing the concentration of PHA. Blending PLA with soy protein aims at reducing production cost, as well as accelerating the biodegradation rate in soil medium. In this work, the mechanical, thermal and morphological properties of the blends were investigated using dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and tensile tests.

  1. Phase equilibria and phase structures of polymer blends

    International Nuclear Information System (INIS)

    Chalykh, Anatolii E; Gerasimov, Vladimir K

    2004-01-01

    Experimental, methodical and theoretical studies dealing with phase equilibria and phase structures of polymer blends are generalised. The general and specific features of the change in solubility of polymers with changes in the molecular mass and copolymer composition and upon the formation of three-dimensional cross-linked networks are described. The results of the effect of the prehistory on the phase structure and the non-equilibrium state of polymer blends are considered in detail.

  2. Assessing the impact of blended learning on student performance

    OpenAIRE

    Do Won Kwak; Flavio Menezes; Carl Sherwood

    2013-01-01

    This paper assesses quantitatively the impact on student performance of a blended learning experiment within a large undergraduate first year course in statistics for business and economics students. We employ a differences- in-difference econometric approach, which controls for differences in student characteristics and course delivery method, to evaluate the impact of blended learning on student performance. Although students in the course manifest a preference for live lectures over online...

  3. Extrudability and Consolidation of Blends between CGM and DDGS

    Directory of Open Access Journals (Sweden)

    C. J. R. Verbeek

    2016-01-01

    Full Text Available During the last decade, the global biofuels industry has experienced exponential growth. By-products such as high protein corn gluten meal (CGM and high fibre distillers dried grains with solubles (DDGS have grown in parallel. CGM has been shown to be suitable as a biopolymer; the high fibre content of DDGS reduces its effectiveness, although it is considerably cheaper. In this study, the processing behaviour of CGM and DDGS blends was evaluated and resulting extrudate properties were determined. Prior to processing, urea was used as a denaturant. DDGS : CGM ratios of 0, 33, 50, 66, and 100% were processed in a single screw extruder, which solely used dissipative heating. Blends containing DDGS were less uniformly consolidated and resulted in more dissipative heating. Blends showed multiple glass transitions, which is characteristic of mechanically compatible blends. Transmission electron microscopy revealed phase separation on a microscale, although distinct CGM or DDGS phases could not be identified. On a macroscale, optical microscopy suggested that CGM-rich blends were better consolidated, supported by visual observations of a more continuous extrudate formed during extrusion. Future work should aim to also characterize the mechanical properties of these blends to assess their suitability as either bioplastic feedstock or pelletized livestock feed.

  4. A Phenomenology of ‘Blending in’: Beyond Emotional Regulation

    Directory of Open Access Journals (Sweden)

    Katie Creighton

    2018-02-01

    Full Text Available The phenomenon of devaluing of self for adolescent girls has been highlighted in previous qualitative research in a US cultural context. Carol Gilligan and her colleagues have documented a loss of connection to self and loss of voice. ‘Blending in’ pertains to such a loss of connection and voice. ‘Blending in’ emerges from many aspects of 8 Irish females’ retrospective qualitative phenomenological accounts of their adolescent experiences. These features of blending in include: a dumbing down of intellectual ability in order to fit in, a desire to be hidden in the group to ‘fade into the background’, to not stand out as being different, fear of being labelled by others and fear of challenging others. Blending in gives phenomenological support to Gilligan’s (1990 accounts of silencing and loss of relation to self in adolescent girls, to a rendering of self as other. This phenomenological exploration is resonant also with de Beauvoir’s Second Sex and to a loss of capacity for introversion in Western culture, echoing Jung (1921. Blending in requires firmer addressing in social and emotional education (SEE, especially regarding challenge to self-management as emotional impulse and behaviour regulation. Self-management as blending in risks being a process of loss of voice and alienation of self.

  5. Teaching of anatomical sciences: A blended learning approach.

    Science.gov (United States)

    Khalil, Mohammed K; Abdel Meguid, Eiman M; Elkhider, Ihsan A

    2018-04-01

    Blended learning is the integration of different learning approaches, new technologies, and activities that combine traditional face-to-face teaching methods with authentic online methodologies. Although advances in educational technology have helped to expand the selection of different pedagogies, the teaching of anatomical sciences has been challenged by implementation difficulties and other limitations. These challenges are reported to include lack of time, costs, and lack of qualified teachers. Easy access to online information and advances in technology make it possible to resolve these limitations by adopting blended learning approaches. Blended learning strategies have been shown to improve students' academic performance, motivation, attitude, and satisfaction, and to provide convenient and flexible learning. Implementation of blended learning strategies has also proved cost effective. This article provides a theoretical foundation for blended learning and proposes a validated framework for the design of blended learning activities in the teaching and learning of anatomical sciences. Clin. Anat. 31:323-329, 2018. © 2018 Wiley Periodicals, Inc. © 2018 Wiley Periodicals, Inc.

  6. Blended learning: how can we optimise undergraduate student engagement?

    Science.gov (United States)

    Morton, Caroline E; Saleh, Sohag N; Smith, Susan F; Hemani, Ashish; Ameen, Akram; Bennie, Taylor D; Toro-Troconis, Maria

    2016-08-04

    Blended learning is a combination of online and face-to-face learning and is increasingly of interest for use in undergraduate medical education. It has been used to teach clinical post-graduate students pharmacology but needs evaluation for its use in teaching pharmacology to undergraduate medical students, which represent a different group of students with different learning needs. An existing BSc-level module on neuropharmacology was redesigned using the Blended Learning Design Tool (BLEnDT), a tool which uses learning domains (psychomotor, cognitive and affective) to classify learning outcomes into those taught best by self-directed learning (online) or by collaborative learning (face-to-face). Two online courses were developed, one on Neurotransmitters and the other on Neurodegenerative Conditions. These were supported with face-to-face tutorials. Undergraduate students' engagement with blended learning was explored by the means of three focus groups, the data from which were analysed thematically. Five major themes emerged from the data 1) Purpose and Acceptability 2) Structure, Focus and Consolidation 3) Preparation and workload 4) Engagement with e-learning component 5) Future Medical Education. Blended learning was acceptable and of interest to undergraduate students learning this subject. They expressed a desire for more blended learning in their courses, but only if it was highly structured, of high quality and supported by tutorials. Students identified that the 'blend' was beneficial rather than purely online learning.

  7. Blended learning as an effective pedagogical paradigm for biomedical science

    Directory of Open Access Journals (Sweden)

    Perry Hartfield

    2013-11-01

    Full Text Available Blended learning combines face-to-face class based and online teaching and learning delivery in order to increase flexibility in how, when, and where students study and learn. The development, integration, and promotion of blended learning in frameworks of curriculum design can optimize the opportunities afforded by information and communication technologies and, concomitantly, accommodate a broad range of student learning styles. This study critically reviews the potential benefits of blended learning as a progressive educative paradigm for the teaching of biomedical science and evaluates the opportunities that blended learning offers for the delivery of accessible, flexible and sustainable teaching and learning experiences. A central tenet of biomedical science education at the tertiary level is the development of comprehensive hands-on practical competencies and technical skills (many of which require laboratory-based learning environments, and it is advanced that a blended learning model, which combines face-to-face synchronous teaching and learning activities with asynchronous online teaching and learning activities, effectively creates an authentic, enriching, and student-centred learning environment for biomedical science. Lastly, a blending learning design for introductory biochemistry will be described as an effective example of integrating face-to-face and online teaching, learning and assessment activities within the teaching domain of biomedical science.   DOI: 10.18870/hlrc.v3i4.169

  8. Impact of ternary blends of biodiesel on diesel engine performance

    Directory of Open Access Journals (Sweden)

    Prem Kumar

    2016-06-01

    Full Text Available The Pongamia and waste cooking oils are the main non edible oils for biodiesel production in India. The aim of the present work is to evaluate the fuel properties and investigate the impact on engine performance using Pongamia and waste cooking biodiesel and their ternary blend with diesel. The investigation of the fuel properties shows that Pongamia biodiesel and waste cooking biodiesel have poor cold flow property. This will lead to starting problem in the engine operation. To overcome this problem the ternary blends of diesel, waste cooking biodiesel and Pongamia biodiesel are prepared. The cloud and pour point for ternary blend, (WCB20:PB20:D60 were found to be 7 °C and 6.5 °C which are comparable to cloud and pour point of diesel 6 °C and 5 °C, respectively. The result of the test showed that brake specific fuel consumption for Pongamia biodiesel and waste cooking biodiesel is higher than ternary blend, (WCB20:PB20:D60 due to their lower energy content. The brake thermal efficiency of ternary blend and diesel is comparable while the Pongamia and waste cooking biodiesel have low efficiency. The result of investigation showed that ternary blend can be developed as alternate fuel.

  9. Reactivity and NO emissions of coal blends during combustion

    Energy Technology Data Exchange (ETDEWEB)

    B. Arias; R.I. Backreedy; A. Arenillas; J.M. Jones; F. Rubiera; M. Pourkashanian; A. Williams; J.J. Pis [Instituto Nacional del Carbon, CSIC, Oviedo (Spain)

    2003-07-01

    This work is focussed on burnout and NO emissions during coal blend combustion. Two different approaches were used. In a first step, experimental work was carried out in a laminar entrained flow reactor (EFR) and then computational techniques were applied to improve the burnout prediction of coals and blend during the experiments. A preliminary study on the combustibility of the samples was made using a thermogravimetric analyser. An entrained flow reactor was employed to study the behaviour of coals and blends at high heating rate and short residence times. Burnout and NO emissions were measured during these experiments. Two methods were used to modelling the combustion in the entrained flow reactor: a commercial CFD code and an advanced char burnout model. Experiments done in the EFR showed that burnout and NO emissions of some blends can be predicted from the weighted average of the values of individual coals, especially when blended coals have the same rank. When a blend is made with coals of different rank, some deviations were observed with respect to the averaged values in burnout and especially in NOx emissions. Burnouts predicted with a commercial CFD code were higher than the experimental values. The use of an advanced char burnout model improved greatly the results, showing the advantages of coupling these two mathematical techniques. 9 refs., 7 figs., 2 tabs.

  10. Modelling of NO formation in the combustion of coal blends

    Energy Technology Data Exchange (ETDEWEB)

    Arenillas, A.; Backreedy, R.I.; Jones, J.M.; Pis, J.J.; Pourkashanian, M.; Rubiera, F.; Williams, A. [CSIC, Instituto Nacional del Carbon, Oviedo (Spain)

    2002-03-01

    Coal blending is becoming of increasing importance in power stations firing pulverised coal as a result of increasing competition, stricter emission legislation and is an attractive way of improving plant economic and combustion performance. Presently, the two general methods used by power station operators to assess or predict the performance of an unknown coal blend to be fired in power station boilers are by the use of experimental large scale rig tests or correlation indices derived from experience of firing other coal blends in the power station environment. The first is expensive and the second is of doubtful accuracy in some cases. This paper evaluates the application of mathematical modelling of the combustion of a series of binary coal blends in the test situation of a drop tube reactor to predict the NO emissions and degree of char burnout. Its applicability to low NOx burners used in power stations is discussed and it is concluded that present mathematical coal combustion models are not developed sufficiently to enable an adequate description of the binary blends and the physical and chemical processes, which may include interactions, during combustion of the blend. This means that accurate predictions cannot be made. 20 refs., 4 figs., 5 tabs.

  11. The combustion of coal blends in a fluidised bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Boavida, Dulce; Abelha, Pedro; Gulyurtlu, Ibrahim; Cabrita, Isabel

    1999-07-01

    Combustion studies of five coals of different origin were carried out in a laboratory scale fluidised bed combustor. Five blends prepared by mixing two coals based on their petrological characterisation, in varying amounts, were selected to study the possibility of reduction NO{sub x}, N{sub 2}O and SO{sub 2} emissions. The results showed that some blends had the opposite behaviour concerning the release of NO{sub x} and SO{sub 2} in relation to parent coals, and the emissions were higher than expected. The N{sub 2}O amounts observed were, however, in almost all blends tested, lower than predicted values. With some blends, the mixing levels intended to reduce SO{sub 2} were not always found to correspond to those for simultaneous decrease of Nox. Most of the blends studied showed some evidence of interaction between them. Varying the proportion of the blend components was observed to alter the temperatures at which interactions were stronger.

  12. Blended Learning Versus Traditional Lecture in Introductory Nursing Pathophysiology Courses.

    Science.gov (United States)

    Blissitt, Andrea Marie

    2016-04-01

    Currently, many undergraduate nursing courses use blended-learning course formats with success; however, little evidence exists that supports the use of blended formats in introductory pathophysiology courses. The purpose of this study was to compare the scores on pre- and posttests and course satisfaction between traditional and blended course formats in an introductory nursing pathophysiology course. This study used a quantitative, quasi-experimental, nonrandomized control group, pretest-posttest design. Analysis of covariance compared pre- and posttest scores, and a t test for independent samples compared students' reported course satisfaction of the traditional and blended course formats. Results indicated that the differences in posttest scores were not statistically significant between groups. Students in the traditional group reported statistically significantly higher satisfaction ratings than students in the blended group. The results of this study support the need for further research of using blended learning in introductory pathophysiology courses in undergraduate baccalaureate nursing programs. Further investigation into how satisfaction is affected by course formats is needed. Copyright 2016, SLACK Incorporated.

  13. Morphological studies on block copolymer modified PA 6 blends

    Energy Technology Data Exchange (ETDEWEB)

    Poindl, M., E-mail: marcus.poindl@ikt.uni-stuttgart.de, E-mail: christian.bonten@ikt.uni-stuttgart.de; Bonten, C., E-mail: marcus.poindl@ikt.uni-stuttgart.de, E-mail: christian.bonten@ikt.uni-stuttgart.de [Institut für Kunststofftechnik, University of Stuttgart (Germany)

    2014-05-15

    Recent studies show that compounding polyamide 6 (PA 6) with a PA 6 polyether block copolymers made by reaction injection molding (RIM) or continuous anionic polymerization in a reactive extrusion process (REX) result in blends with high impact strength and high stiffness compared to conventional rubber blends. In this paper, different high impact PA 6 blends were prepared using a twin screw extruder. The different impact modifiers were an ethylene propylene copolymer, a PA PA 6 polyether block copolymer made by reaction injection molding and one made by reactive extrusion. To ensure good particle matrix bonding, the ethylene propylene copolymer was grafted with maleic anhydride (EPR-g-MA). Due to the molecular structure of the two block copolymers, a coupling agent was not necessary. The block copolymers are semi-crystalline and partially cross-linked in contrast to commonly used amorphous rubbers which are usually uncured. The combination of different analysis methods like atomic force microscopy (AFM), transmission electron microscopy (TEM) and scanning electron microscopy (SEM) gave a detailed view in the structure of the blends. Due to the partial cross-linking, the particles of the block copolymers in the blends are not spherical like the ones of ethylene propylene copolymer. The differences in molecular structure, miscibility and grafting of the impact modifiers result in different mechanical properties and different blend morphologies.

  14. Chemical and Enzymatic Hydrolysis of Polyurethane/Polylactide Blends

    Directory of Open Access Journals (Sweden)

    Joanna Brzeska

    2015-01-01

    Full Text Available Polyether-esterurethanes containing synthetic poly[(R,S-3-hydroxybutyrate] (R,S-PHB and polyoxytetramethylenediol in soft segments and polyesterurethanes with poly(ε-caprolactone and poly[(R,S-3-hydroxybutyrate] were blended with poly([D,L]-lactide (PLA. The products were tested in terms of their oil and water absorption. Oil sorption tests of polyether-esterurethane revealed their higher response in comparison to polyesterurethanes. Blending of polyether-esterurethanes with PLA caused the increase of oil sorption. The highest water sorption was observed for blends of polyether-esterurethane, obtained with 10% of R,S-PHB in soft segments. The samples mass of polyurethanes and their blends were almost not changed after incubation in phosphate buffer and trypsin and lipase solutions. Nevertheless the molecular weight of polymers was significantly reduced after degradation. It was especially visible in case of incubation of samples in phosphate buffer what suggested the chemical hydrolysis of polymer chains. The changes of surface of polyurethanes and their blends, after incubation in both enzymatic solutions, indicated on enzymatic degradation, which had been started despite the lack of mass lost. Polyurethanes and their blends, contained more R,S-PHB in soft segments, were degraded faster.

  15. Durability of Gamma Irradiated Polymer Impregnated Blended Cement Pastes

    International Nuclear Information System (INIS)

    Khattab, M.M.; Abdel-Rahman, H.A.; Younes, M.M.

    2010-01-01

    This study is focusing on durability and performance of the neat blended cement paste as well as those of the polymer-impregnated paste towards seawater and various concentrations of magnesium sulfate solutions up to 6 months of curing. The neat blended cement paste is prepared by a partial substitution of ordinary Portland cement with 5% of active rice husk ash (RHA). These samples were cured under tap water for 7 days. Similar samples were impregnated with unsaturated polyester resin (UPE) and subjected to various doses of gamma rays ranging from 10 to 50 kGy. The results showed that the irradiated impregnated specimens gave higher values of compressive strength than the neat blended cement paste specimens. On immersing the neat blended cement specimens and polymer impregnated specimens especially that irradiated at 30 kGy in seawater and different concentrations of magnesium sulfate solutions up to 6 months of curing, the results showed that the polymer impregnated blended cement (OPC-RHA-UPE) paste have a good resistance towards aggressive media as compared to the neat blended cement (OPC-RHA) paste. The results also indicated that the sea water has a greater corrosive effect than the magnesium sulfate solutions. These results were confirmed by scanning electron microscopy (SEM) and mercury intrusion porosimetry (MIP)

  16. Morphological, rheological and mechanical characterization of polypropylene nanocomposite blends.

    Science.gov (United States)

    Rosales, C; Contreras, V; Matos, M; Perera, R; Villarreal, N; García-López, D; Pastor, J M

    2008-04-01

    In the present work, the effectiveness of styrene/ethylene-butylene/styrene rubbers grafted with maleic anhydride (MA) and a metallocene polyethylene (mPE) as toughening materials in binary and ternary blends with polypropylene and its nanocomposite as continuous phases was evaluated in terms of transmission electron microscopy (TEM), scanning electron microscopy (SEM), oscillatory shear flow and dynamic mechanical thermal analysis (DMA). The flexural modulus and heat distortion temperature values were determined as well. A metallocene polyethylene and a polyamide-6 were used as dispersed phases in these binary and ternary blends produced via melt blending in a corotating twin-screw extruder. Results showed that the compatibilized blends prepared without clay are tougher than those prepared with the nanocomposite of PP as the matrix phase and no significant changes in shear viscosity, melt elasticity, flexural or storage moduli and heat distortion temperature values were observed between them. However, the binary blend with a nanocomposite of PP as matrix and metallocene polyethylene phase exhibited better toughness, lower shear viscosity, flexural modulus, and heat distortion temperature values than that prepared with polyamide-6 as dispersed phase. These results are related to the degree of clay dispersion in the PP and to the type of morphology developed in the different blends.

  17. Preparation of LDPE/LNR Blend Via Emulsion Dispersion

    International Nuclear Information System (INIS)

    Rusli Daik; Yee Lee Ching

    2007-01-01

    Low density polyethylene (LDPE)/ liquid natural rubber (LNR) blends with the composition of 100LDPE/ 0LNR, 70LDPE/ 30LNR, 60LDPE/ 40LNR and 40LDPE/ 60LNR were prepared via dispersion of LDPE and LNR emulsion. LNR was obtained via photochemical sensitization of natural rubber (NR). Emulsion of LNR was prepared by using sodium dodecyl sulfate (SDS) and 1-hexanol as the emulsifier and co- emulsifier respectively. Emulsion of LDPE was prepared in the same way by using LDPE solution in carbon tetrachloride, SDS and 1-hexanol. LDPE/ LNR blends were prepared via mixing of LNR and LDPE emulsions. Mechanical properties of the blends were analyzed by tensile, hardness and impact test. Optimum mechanical properties were observed for composite with composition of 60LDPE/ 40LNR that showed the maximum value of stress and strain. The glass transition temperature, T g , of the blends as obtained from differential scanning calorimetric (DSC) showed that the blends were homogeneous. Morphology study by using scanning electron microscopy (SEM) also indicates the homogeneity of LDPE/ LNR blends produced. (author)

  18. Preparation and Characterization of Keratin/Alginate Blend Microparticles

    Directory of Open Access Journals (Sweden)

    Yaowalak Srisuwan

    2018-01-01

    Full Text Available The water-in-oil (W/O emulsification-diffusion method was used for construction of keratin (Ker, alginate (Alg, and Ker/Alg blend microparticles. The Ker, Alg, and Ker/Alg blend solutions were used as the water phase, while ethyl acetate was used as the oil phase. Firstly, different concentrations of Ker solution was used to find suitable content. 1.6% w/v Ker solution was blended with the same concentration of the Alg solution for further microparticle construction. Results from scanning electron microscope analysis show that the microparticles have different shapes: spherical, bowl-like, porous, and hollow, with several sizes depending on the blend ratio. FTIR and TG analyses indicated that the secondary structure and thermal stability of the microparticles were influenced by the Ker/Alg blend ratio. The interaction between functional groups of keratin and alginate was the main factor for both β-sheet structure and Td,max values of the microparticles. The results suggested that Ker/Alg blend microparticles might be applied in many fields by varying the Ker/Alg ratio.

  19. Non-isothermal crystallization of PET/PLA blends

    International Nuclear Information System (INIS)

    Chen, Huipeng; Pyda, Marek; Cebe, Peggy

    2009-01-01

    Binary blends of poly(ethylene terephthalate) with poly(lactic acid), PET/PLA, were studied by differential scanning calorimetry and X-ray scattering. The PET/PLA blends, prepared by solution casting, were found to be miscible in the melt over the entire composition range. Both quenched amorphous and semicrystalline blends exhibit a single, composition dependent glass transition temperature. We report the non-isothermal crystallization of (a) PET, with and without the presence of PLA crystals and (b) PLA, with and without the presence of PET crystals. PET can crystallize in all blends, regardless of whether PLA is amorphous or crystalline, and degree of crystallinity of PET decreases as PLA content increases. In contrast, PLA crystallization is strongly affected by the mobility of the PET fraction. When PET is wholly amorphous, PLA can crystallize even in 70/30 blends, albeit weakly. But when PET is crystalline, PLA cannot crystallize when its own content drops below 0.90. These different behaviors may possibly be related to the tendency of each polymer to form constrained chains, i.e., to form the rigid amorphous fraction, or RAF. PET is capable of forming a large amount of RAF, whereas relatively smaller amount of RAF forms in PLA. Like the crystals, the rigid amorphous fraction of one polymer component may inhibit the growth of crystals of the other blend partner.

  20. Coalescence in PLA-PBAT blends under shear flow: Effects of blend preparation and PLA molecular weight

    Energy Technology Data Exchange (ETDEWEB)

    Nofar, M. [Center for High Performance Polymer and Composite Systems (CREPEC), Chemical Engineering Department, Polytechnique Montreal, Montreal, Quebec H3T 1J4, Canada and CREPEC, Department of Chemical Engineering, McGill University, Montreal, Quebec H3A 2B2 (Canada); Heuzey, M. C.; Carreau, P. J., E-mail: pierre.carreau@polymtl.ca [Center for High Performance Polymer and Composite Systems (CREPEC), Chemical Engineering Department, Polytechnique Montreal, Montreal, Quebec H3T 1J4 (Canada); Kamal, M. R. [CREPEC, Department of Chemical Engineering, McGill University, Montreal, Quebec H3A 2B2 (Canada); Randall, J. [NatureWorks LLC, 15305 Minnetonka Boulevard, Minnetonka, Minnesota 55345 (United States)

    2016-07-15

    Blends containing 75 wt. % of an amorphous polylactide (PLA) with two different molecular weights and 25 wt. % of a poly[(butylene adipate)-co-terephthalate] (PBAT) were prepared using either a Brabender batch mixer or a twin-screw extruder. These compounds were selected because blending PLA with PBAT can overcome various drawbacks of PLA such as its brittleness and processability limitations. In this study, we investigated the effects of varying the molecular weight of the PLA matrix and of two different mixing processes on the blend morphology and, further, on droplet coalescence during shearing. The rheological properties of these blends were investigated and the interfacial properties were analyzed using the Palierne emulsion model. Droplet coalescence was investigated by applying shear flows of 0.05 and 0.20 s{sup −1} at a fixed strain of 60. Subsequently, small amplitude oscillatory shear tests were conducted to investigate changes in the viscoelastic properties. The morphology of the blends was also examined using scanning electron microscope (SEM) micrographs. It was observed that the PBAT droplets were much smaller when twin-screw extrusion was used for the blend preparation. Shearing at 0.05 s{sup −1} induced significant droplet coalescence in all blends, but coalescence and changes in the viscoelastic properties were much more pronounced for the PLA-PBAT blend based on a lower molecular weight PLA. The viscoelastic responses were also somehow affected by the thermal degradation of the PLA matrix during the experiments.

  1. Recombinant protein blends: silk beyond natural design.

    Science.gov (United States)

    Dinjaski, Nina; Kaplan, David L

    2016-06-01

    Recombinant DNA technology and new material concepts are shaping future directions in biomaterial science for the design and production of the next-generation biomaterial platforms. Aside from conventionally used synthetic polymers, numerous natural biopolymers (e.g., silk, elastin, collagen, gelatin, alginate, cellulose, keratin, chitin, polyhydroxyalkanoates) have been investigated for properties and manipulation via bioengineering. Genetic engineering provides a path to increase structural and functional complexity of these biopolymers, and thereby expand the catalog of available biomaterials beyond that which exists in nature. In addition, the integration of experimental approaches with computational modeling to analyze sequence-structure-function relationships is starting to have an impact in the field by establishing predictive frameworks for determining material properties. Herein, we review advances in recombinant DNA-mediated protein production and functionalization approaches, with a focus on hybrids or combinations of proteins; recombinant protein blends or 'recombinamers'. We highlight the potential biomedical applications of fibrous protein recombinamers, such as Silk-Elastin Like Polypeptides (SELPs) and Silk-Bacterial Collagens (SBCs). We also discuss the possibility for the rationale design of fibrous proteins to build smart, stimuli-responsive biomaterials for diverse applications. We underline current limitations with production systems for these proteins and discuss the main trends in systems/synthetic biology that may improve recombinant fibrous protein design and production. Copyright © 2016. Published by Elsevier Ltd.

  2. Coherent Spatial and Colour Blended Exemplar Inpainting

    Directory of Open Access Journals (Sweden)

    ANAM AKBAR

    2017-04-01

    Full Text Available In an image processing field the digital image recovery is termed as inpainting. Efficient retrieval of an image, especially having large objects with high curvature and complex texture is an immensely challenging problem for image inpainting researchers and practitioner. This enthused researchers and emerge various inpainting algorithms and many are in progress. Generally inpainting techniques approaches the available area source of given image(s to restore the unavailable area target by the information available at the target edge. This paper represents a novel approach BSDD (Blended Spatial and Dimensional Distances by sampling patches at each pixel of the source region. From the given sample, selection of local edge patch is gradient based without priority computation overhead as previous techniques. These local patches are searched globally by linear distance in which both spatial and dimensional distances are considered with regularization factor. The main motive of this method consists in achieving the efficiency, curvature and textural challenges of inpainting without compromising the quality of inpainted image. We have tested the proposed method in real as well as synthetic images with high curvature and complex textures in all cases results are comparable with other well-known techniques. In view of quality and optical the proposed algorithm exhibits better results.

  3. Engaging Students' Learning Through a Blended Environment

    Directory of Open Access Journals (Sweden)

    Andrew Stuart

    2013-05-01

    Full Text Available Within the furniture manufacturing industry a high proportion of occupational accidents are as a result of non-compliance to machining regulations and incorrect work practices. Safety training plays an important role in reducing accidents and promoting a safety culture within this sector. This article details an action research study undertaken during the first year of a new Degree in Timber Product Technology, which set out to evaluate the impact a blended learning environment and reusable learning objects (RLOs could have on promoting safe work practices and a safety culture amongst students. A constructivist approach was taken and the module design was underpinned by Kolb’s model of experiential learning, placing more responsibility on the learners for their own learning and encouraging them to reflect upon their experiences. The findings of this study suggest that students with prior industry machining experience required a change in their attitude to machining which was achieved within the practical labs, while students with no machining experiences were intimidated by the learning environment in the practical labs but whose learning experience was enhanced through the use of RLOs and other eLearning resources. In order to reduce occupational accidents in the furniture manufacturing industry the promotion of continuing professional development (CPD training courses is required in order to change workers’ behaviour to machine safety and encourage lifelong learning so as to promote a safety culture within the furniture manufacturing industry.

  4. Blended learning in the small animal clinic

    DEFF Research Database (Denmark)

    Langebæk, Rikke

    2011-01-01

    At the Department of Small Animal Clinical Sciences, Basic Surgical Skills are taught in groups of 30-35 students in the first year of the master program (4th year students). The eight day course is an example of ‘blended learning’ in which students use our e-learning-material (Step 1) to prepare...... for the practical part of the course (Step 2, 3 and 4). From their home computers, students log on to the e-learning platform of Copenhagen University: https://absalon.ku.dk and go to the Basic Surgical Skills course, which consist of a line of chapters concerning a variety of surgical subjects. Each subject...... the implementation of these new teaching methods (e-learning and Skills Lab), teachers have ascertained a more satisfactory level of preparation, students that seem more focused and live-animal surgery that is conducted at a more ‘professional’ level than before. Finally, our research in this field shows...

  5. Refining and blending of aviation turbine fuels.

    Science.gov (United States)

    White, R D

    1999-02-01

    Aviation turbine fuels (jet fuels) are similar to other petroleum products that have a boiling range of approximately 300F to 550F. Kerosene and No.1 grades of fuel oil, diesel fuel, and gas turbine oil share many similar physical and chemical properties with jet fuel. The similarity among these products should allow toxicology data on one material to be extrapolated to the others. Refineries in the USA manufacture jet fuel to meet industry standard specifications. Civilian aircraft primarily use Jet A or Jet A-1 fuel as defined by ASTM D 1655. Military aircraft use JP-5 or JP-8 fuel as defined by MIL-T-5624R or MIL-T-83133D respectively. The freezing point and flash point are the principle differences between the finished fuels. Common refinery processes that produce jet fuel include distillation, caustic treatment, hydrotreating, and hydrocracking. Each of these refining processes may be the final step to produce jet fuel. Sometimes blending of two or more of these refinery process streams are needed to produce jet fuel that meets the desired specifications. Chemical additives allowed for use in jet fuel are also defined in the product specifications. In many cases, the customer rather than the refinery will put additives into the fuel to meet their specific storage or flight condition requirements.

  6. De‐blending reverse‐time migration

    KAUST Repository

    Fei, Tong W.

    2010-10-17

    Reverse‐time migration (RTM), based on the full two‐way wave equation, has gained interest and become a popular imaging tool for complex structures in the last few years. The method is well‐known for its ability to better image the steeply dipping and overturned structures than the migration methods based on the one‐way wave equation extrapolation. However, the RTM image often contains low frequency and back‐scattering noise, and the imaging quality is sensitive to the migration velocity. In order to improve the RTM imaging quality and make the RTM image less sensitive to the velocity model, we developed an RTM de‐blending technique which separates upgoing and downgoing source and receiver wavefields, and then use them to construct final RTM images. Test results show that decomposed images obtained from only the downgoing source and receiver wavefields are less sensitive to velocity. It removes unwanted noise and migration artifacts from conventional RTM, and the imaging quality is greatly improved compared with a conventional RTM image.

  7. De‐blending reverse‐time migration

    KAUST Repository

    Fei, Tong W.; Luo, Yi; Schuster, Gerard T.

    2010-01-01

    Reverse‐time migration (RTM), based on the full two‐way wave equation, has gained interest and become a popular imaging tool for complex structures in the last few years. The method is well‐known for its ability to better image the steeply dipping and overturned structures than the migration methods based on the one‐way wave equation extrapolation. However, the RTM image often contains low frequency and back‐scattering noise, and the imaging quality is sensitive to the migration velocity. In order to improve the RTM imaging quality and make the RTM image less sensitive to the velocity model, we developed an RTM de‐blending technique which separates upgoing and downgoing source and receiver wavefields, and then use them to construct final RTM images. Test results show that decomposed images obtained from only the downgoing source and receiver wavefields are less sensitive to velocity. It removes unwanted noise and migration artifacts from conventional RTM, and the imaging quality is greatly improved compared with a conventional RTM image.

  8. Thermal Stabilization FY 1999 blend plan

    Energy Technology Data Exchange (ETDEWEB)

    RISENMAY, H.R.

    1999-02-23

    This Blend Plan documents the alternate feed material items for the thermal stabilization process that will be used in place of the metal items that were originally planned to be processed. Problems with resolution of the safety basis for the metal items resulted in the decision to run material that already had an established safety basis. Various in process and scrap recovery items stored in gloveboxes, plutonium oxide and plutonium oxide mixed with uranium oxide stored in 2736-Z vaults will be processed through the stabilization furnaces until the safety basis for the metal items has been resolved. The purpose of thermal stabilization is to heat the material to 1000 degrees Celsius to drive off all volatile materials and leave the plutonium and/or uranium as oxides. The stabilized material will be sampled to determine the Loss On Ignition (LOI). The stabilized material must meet LOI of less than 0.5% to be acceptable for storage under DOE-STD-3013-94 specifications. Out of specification material will be recycled through the furnaces until the LOI limits are met.

  9. Thermal Stabilization FY 1999 blend plan

    International Nuclear Information System (INIS)

    RISENMAY, H.R.

    1999-01-01

    This Blend Plan documents the alternate feed material items for the thermal stabilization process that will be used in place of the metal items that were originally planned to be processed. Problems with resolution of the safety basis for the metal items resulted in the decision to run material that already had an established safety basis. Various in process and scrap recovery items stored in gloveboxes, plutonium oxide and plutonium oxide mixed with uranium oxide stored in 2736-Z vaults will be processed through the stabilization furnaces until the safety basis for the metal items has been resolved. The purpose of thermal stabilization is to heat the material to 1000 degrees Celsius to drive off all volatile materials and leave the plutonium and/or uranium as oxides. The stabilized material will be sampled to determine the Loss On Ignition (LOI). The stabilized material must meet LOI of less than 0.5% to be acceptable for storage under DOE-STD-3013-94 specifications. Out of specification material will be recycled through the furnaces until the LOI limits are met

  10. Thermal stabilization FY 1999 blend plan

    International Nuclear Information System (INIS)

    RISENMAY, H.R.

    1999-01-01

    This Blend Plan documents the alternate feed material items for the thermal stabilization process that will be used in place of the metal items that were originally planned to be processed. Problems with resolution of the safety basis for the metal items resulted in the decision to run material that already had an established safety basis. Various in process and scrap recovery items stored in gloveboxes, plutonium oxide and plutonium oxide mixed with uranium oxide stored in 2736-2 vaults will be processed through the stabilization furnaces until the safety basis for the metal items has been resolved. The purpose of thermal stabilization is to heat the material to 1000 degrees Celsius to drive off all volatile materials and leave the plutonium and/or uranium as oxides. The stabilized material will be sampled to determine the Loss On Ignition (LOI). The stabilized material must meet LOI of less than 0.5% to be acceptable for storage under DOE-STD-3013-94 specifications. Out of specification material will be recycled through the furnaces until the LOI limits are met

  11. Thermal stabilization FY 1999 blend plan

    Energy Technology Data Exchange (ETDEWEB)

    RISENMAY, H.R.

    1999-06-01

    This Blend Plan documents the alternate feed material items for the thermal stabilization process that will be used in place of the metal items that were originally planned to be processed. Problems with resolution of the safety basis for the metal items resulted in the decision to run material that already had an established safety basis. Various in process and scrap recovery items stored in gloveboxes, plutonium oxide and plutonium oxide mixed with uranium oxide stored in 2736-2 vaults will be processed through the stabilization furnaces until the safety basis for the metal items has been resolved. The purpose of thermal stabilization is to heat the material to 1000 degrees Celsius to drive off all volatile materials and leave the plutonium and/or uranium as oxides. The stabilized material will be sampled to determine the Loss On Ignition (LOI). The stabilized material must meet LOI of less than 0.5% to be acceptable for storage under DOE-STD-3013-94 specifications. Out of specification material will be recycled through the furnaces until the LOI limits are met.

  12. Thin films of polymer blends deposited by matrix-assisted pulsed laser evaporation: Effects of blending ratios

    International Nuclear Information System (INIS)

    Paun, Irina Alexandra; Ion, Valentin; Moldovan, Antoniu; Dinescu, Maria

    2011-01-01

    In this work, we show successful use of matrix-assisted pulsed laser evaporation (MAPLE) for obtaining thin films of PEG:PLGA blends, in the view of their use for controlled drug delivery. In particular, we investigate the influence of the blending ratios on the characteristics of the films. We show that the roughness of the polymeric films is affected by the ratio of each polymer within the blend. In addition, we perform Fourier transformed infrared spectroscopy (FTIR) measurements and we find that the intensities ratios of the infrared absorption bands of the two polymers are consistent with the blending ratios. Finally, we assess the optical constants of the polymeric films by spectroscopic ellipsometry (SE). We point out that the blending ratios exert an influence on the optical characteristics of the films and we validate the SE results by atomic force microscopy and UV-vis spectrophotometry. In all, we stress that the ratios in which the two polymers are blended have significant impact on the morphology, chemical structure and optical characteristics of the polymeric films deposited by MAPLE.

  13. Design of tailor-made chemical blend using a decomposition-based computer-aided approach

    DEFF Research Database (Denmark)

    Yunus, Nor Alafiza; Gernaey, Krist; Manan, Z.A.

    2011-01-01

    Computer aided techniques form an efficient approach to solve chemical product design problems such as the design of blended liquid products (chemical blending). In chemical blending, one tries to find the best candidate, which satisfies the product targets defined in terms of desired product...... methodology for blended liquid products that identifies a set of feasible chemical blends. The blend design problem is formulated as a Mixed Integer Nonlinear Programming (MINLP) model where the objective is to find the optimal blended gasoline or diesel product subject to types of chemicals...... and their compositions and a set of desired target properties of the blended product as design constraints. This blend design problem is solved using a decomposition approach, which eliminates infeasible and/or redundant candidates gradually through a hierarchy of (property) model based constraints. This decomposition...

  14. KOREA'S BLENDED LEARNING IN NURSING: ISSUES AND THE WAY FORWARD

    Directory of Open Access Journals (Sweden)

    Claire Su-Yeon Park

    2017-01-01

    Full Text Available Blended learning is receiving significant scholarly attention in Korean nursing education for a number of reasons: the downsizing of universities due to low birth rates; the high demand for nurses in a super-aged society; and nursing’s distinctive characteristics, i.e., theory-driven practical scholarship (Park, 2016. However, the lack of scholarly evidence on this subject suggests that current nursing scholarship is not satisfying the needs of the times. This article thus addressed problems in the current literature on Korea’s blended learning in nursing and suggested a way forward for the future. A rigorous literature review and synthesis were conducted from July 01 to August 10, 2016 using an electronic database operated by Korea Education & Research Information Service. The key words were “blended learning” and “nursing.” The search result included twelve publications on “blended learning” and “nursing” in Korea and thirty publications on “blended learning” and “nursing” in other countries. All articles were first scrutinized by the author for relevance to blended learning in nursing and were then compared and synthesized. Korean articles had straight research structures from central casting in contrast to the articles from other countries. Specifically, these structures included 1 an ambiguous definition of the scope of blended learning: i.e., multiple instructional methods or delivery media, rather than an integration of technology-mediated instruction into a face-to-face (F2F learning environment (Bonk & Graham, 2005; “enhancing blends[1]” rather than “enabling blends” or “transforming blends” (Bonk & Graham, 2005, see Table 1: Different categories of blended learning systems, 2 a very small sample size with a limited location, 3 the use of very basic descriptive statistical analyses, 4 undifferentiated types of a blended learning: i.e., most articles referred to blended learning in nursing

  15. Assessment of Blend PVDF Membranes, and the Effect of Polymer Concentration and Blend Composition.

    Science.gov (United States)

    Ali, Imtiaz; Bamaga, Omar A; Gzara, Lassaad; Bassyouni, M; Abdel-Aziz, M H; Soliman, M F; Drioli, Enrico; Albeirutty, Mohammed

    2018-03-05

    In this work, PVDF homopolymer was blended with PVDF-co-HFP copolymer and studied in terms of morphology, porosity, pore size, hydrophobicity, permeability, and mechanical properties. Different solvents, namely N-Methyl-2 pyrrolidone (NMP), Tetrahydrofuran (THF), and Dimethylformamide (DMF) solvents, were used to fabricate blended PVDF flat sheet membranes without the introduction of any pore forming agent, through a non-solvent induced phase separation (NIPS) technique. Furthermore, the performance of the fabricated membranes was investigated for pressure and thermal driven applications. The porosity of the membranes was slightly increased with the increase in the overall content of PVDF and by the inclusion of PVDF copolymer. Total PVDF content, copolymer content, and mixed-solvent have a positive effect on mechanical properties. The addition of copolymer increased the hydrophobicity when the total PVDF content was 20%. At 25% and with the inclusion of mixed-solvent, the hydrophobicity was adversely affected. The permeability of the membranes increased with the increase in the overall content of PVDF. Mixed-solvents significantly improved permeability.

  16. Assessment of Blend PVDF Membranes, and the Effect of Polymer Concentration and Blend Composition

    Directory of Open Access Journals (Sweden)

    Imtiaz Ali

    2018-03-01

    Full Text Available In this work, PVDF homopolymer was blended with PVDF-co-HFP copolymer and studied in terms of morphology, porosity, pore size, hydrophobicity, permeability, and mechanical properties. Different solvents, namely N-Methyl-2 pyrrolidone (NMP, Tetrahydrofuran (THF, and Dimethylformamide (DMF solvents, were used to fabricate blended PVDF flat sheet membranes without the introduction of any pore forming agent, through a non-solvent induced phase separation (NIPS technique. Furthermore, the performance of the fabricated membranes was investigated for pressure and thermal driven applications. The porosity of the membranes was slightly increased with the increase in the overall content of PVDF and by the inclusion of PVDF copolymer. Total PVDF content, copolymer content, and mixed-solvent have a positive effect on mechanical properties. The addition of copolymer increased the hydrophobicity when the total PVDF content was 20%. At 25% and with the inclusion of mixed-solvent, the hydrophobicity was adversely affected. The permeability of the membranes increased with the increase in the overall content of PVDF. Mixed-solvents significantly improved permeability.

  17. Thermoset Blends of an Epoxy Resin and Polydicyclopentadiene

    Energy Technology Data Exchange (ETDEWEB)

    Rohde, Brian J.; Le, Kim Mai; Krishnamoorti, Ramanan; Robertson, Megan L.

    2016-12-13

    The mechanical properties of two chemically distinct and complementary thermoset polymers were manipulated through development of thermoset blends. The thermoset blend system was composed of an anhydride-cured diglycidyl ether of bisphenol A (DGEBA)-based epoxy resin, contributing high tensile strength and modulus, and polydicyclopentadiene (PDCPD), which has a higher toughness and impact strength as compared to other thermoset polymers. Ultra-small-angle and small-angle X-ray scattering analysis explored the morphology of concurrently cured thermoset blends, revealing a macroscopically phase separated system with a surface fractal structure across blended systems of varying composition. The epoxy resin rich and PDCPD rich phases exhibited distinct glass transitions (Tg’s): the Tg observed at higher temperature was associated with the epoxy resin rich phase and was largely unaffected by the presence of PDCPD, whereas the PDCPD rich phase Tg systematically decreased with increasing epoxy resin content due to inhibition of dicyclopentadiene ring-opening metathesis polymerization. The mechanical properties of these phase-separated blends were in reasonable agreement with predictions by the rule of mixtures for the blend tensile strength, modulus, and fracture toughness. Scanning electron microscopy analysis of the tensile and fracture specimen fracture surfaces showed an increase in energy dissipation mechanisms, such as crazing, shear banding, and surface roughness, as the fraction of the more ductile component, PDPCD, increased. These results present a facile method to tune the mechanical properties of a toughened thermoset network, in which the high modulus and tensile strength of the epoxy resin can be largely retained at high epoxy resin content in the blend, while increasing the fracture toughness.

  18. Degradable polyphosphazene/poly(alpha-hydroxyester) blends: degradation studies.

    Science.gov (United States)

    Ambrosio, Archel M A; Allcock, Harry R; Katti, Dhirendra S; Laurencin, Cato T

    2002-04-01

    Biomaterials based on the polymers of lactic acid and glycolic acid and their copolymers are used or studied extensively as implantable devices for drug delivery, tissue engineering and other biomedical applications. Although these polymers have shown good biocompatibility, concerns have been raised regarding their acidic degradation products, which have important implications for long-term implantable systems. Therefore, we have designed a novel biodegradable polyphosphazene/poly(alpha-hydroxyester) blend whose degradation products are less acidic than those of the poly(alpha-hydroxyester) alone. In this study, the degradation characteristics of a blend of poly(lactide-co-glycolide) (50:50 PLAGA) and poly[(50% ethyl glycinato)(50% p-methylphenoxy) phosphazene] (PPHOS-EG50) were qualitatively and quantitatively determined with comparisons made to the parent polymers. Circular matrices (14mm diameter) of the PLAGA, PPHOS-EG50 and PLAGA-PPHOS-EG50 blend were degraded in non-buffered solutions (pH 7.4). The degraded polymers were characterized for percentage mass loss and molecular weight and the degradation medium was characterized for acid released in non-buffered solutions. The amounts of neutralizing base necessary to bring about neutral pH were measured for each polymer or polymer blend during degradation. The poly(phosphazene)/poly(lactide-co-glycolide) blend required significantly less neutralizing base in order to bring about neutral solution pH during the degradation period studied. The results indicated that the blend degraded at a rate intermediate to that of the parent polymers and that the degradation products of the polyphosphazene neutralized the acidic degradation products of PLAGA. Thus, results from these in vitro degradation studies suggest that the PLAGA-PPHOS-EG50 blend may provide a viable improvement to biomaterials based on acid-releasing organic polymers.

  19. Proton exchange membranes based on PVDF/SEBS blends

    Energy Technology Data Exchange (ETDEWEB)

    Mokrini, A.; Huneault, M.A. [Industrial Materials Institute, National Research Council of Canada, 75 de Mortagne Blvd., Boucherville, Que. (Canada J4B 6Y4)

    2006-03-09

    Proton-conductive polymer membranes are used as an electrolyte in the so-called proton exchange membrane fuel cells. Current commercially available membranes are perfluorosulfonic acid polymers, a class of high-cost ionomers. This paper examines the potential of polymer blends, namely those of styrene-(ethylene-butylene)-styrene block copolymer (SEBS) and polyvinylidene fluoride (PVDF), in the proton exchange membrane application. SEBS/PVDF blends were prepared by twin-screw extrusion and the membranes were formed by calendering. SEBS is a phase-segregated material where the polystyrene blocks can be selectively functionalized offering high ionic conductivity, while PVDF insures good dimensional stability and chemical resistance to the films. Proton conductivity of the films was obtained by solid-state grafting of sulfonic acid moieties. The obtained membranes were characterized in terms of conductivity, ionic exchange capacity and water uptake. In addition, the membranes were characterized in terms of morphology, microstructure and thermo-mechanical properties to establish the blends morphology-property relationships. Modification of interfacial properties between SEBS and PVDF was found to be a key to optimize the blends performance. Addition of a methyl methacrylate-butyl acrylate-methyl methacrylate block copolymer (MMA-BA-MMA) was found to compatibilize the blend by reducing the segregation scale and improving the blend homogeneity. Mechanical resistance of the membranes was also improved through the addition of this compatibilizer. As little as 2wt.% compatibilizer was sufficient for complete interfacial coverage and lead to improved mechanical properties. Compatibilized blend membranes also showed higher conductivities, 1.9x10{sup -2} to 5.5x10{sup -3}Scm{sup -1}, and improved water management. (author)

  20. Blending Of Radioactive Salt Solutions In Million Gallon Tanks

    Energy Technology Data Exchange (ETDEWEB)

    Leishear, Robert A.; Lee, Si Y.; Fowley, Mark D.; Poirier, Michael R.

    2012-12-10

    Research was completed at Savannah River National Laboratory (SRNL) to investigate processes related to the blending of radioactive, liquid waste, salt solutions in 4920 cubic meter, 25.9 meter diameter storage tanks. One process was the blending of large salt solution batches (up to 1135 ? 3028 cubic meters), using submerged centrifugal pumps. A second process was the disturbance of a settled layer of solids, or sludge, on the tank bottom. And a third investigated process was the settling rate of sludge solids if suspended into slurries by the blending pump. To investigate these processes, experiments, CFD models (computational fluid dynamics), and theory were applied. Experiments were performed using simulated, non-radioactive, salt solutions referred to as supernates, and a layer of settled solids referred to as sludge. Blending experiments were performed in a 2.44 meter diameter pilot scale tank, and flow rate measurements and settling tests were performed at both pilot scale and full scale. A summary of the research is presented here to demonstrate the adage that, ?One good experiment fixes a lot of good theory?. Experimental testing was required to benchmark CFD models, or the models would have been incorrectly used. In fact, CFD safety factors were established by this research to predict full-scale blending performance. CFD models were used to determine pump design requirements, predict blending times, and cut costs several million dollars by reducing the number of required blending pumps. This research contributed to DOE missions to permanently close the remaining 47 of 51 SRS waste storage tanks.

  1. Blending of Radioactive Salt Solutions in Million Gallon Tanks - 13002

    International Nuclear Information System (INIS)

    Leishear, Robert A.; Lee, Si Y.; Fowley, Mark D.; Poirier, Michael R.

    2013-01-01

    Research was completed at Savannah River National Laboratory (SRNL) to investigate processes related to the blending of radioactive, liquid waste, salt solutions in 4920 cubic meter, 25.9 meter diameter storage tanks. One process was the blending of large salt solution batches (up to 1135 - 3028 cubic meters), using submerged centrifugal pumps. A second process was the disturbance of a settled layer of solids, or sludge, on the tank bottom. And a third investigated process was the settling rate of sludge solids if suspended into slurries by the blending pump. To investigate these processes, experiments, CFD models (computational fluid dynamics), and theory were applied. Experiments were performed using simulated, non-radioactive, salt solutions referred to as supernates, and a layer of settled solids referred to as sludge. Blending experiments were performed in a 2.44 meter diameter pilot scale tank, and flow rate measurements and settling tests were performed at both pilot scale and full scale. A summary of the research is presented here to demonstrate the adage that, 'One good experiment fixes a lot of good theory'. Experimental testing was required to benchmark CFD models, or the models would have been incorrectly used. In fact, CFD safety factors were established by this research to predict full-scale blending performance. CFD models were used to determine pump design requirements, predict blending times, and cut costs several million dollars by reducing the number of required blending pumps. This research contributed to DOE missions to permanently close the remaining 47 of 51 SRS waste storage tanks. (authors)

  2. Blending of Radioactive Salt Solutions in Million Gallon Tanks - 13002

    Energy Technology Data Exchange (ETDEWEB)

    Leishear, Robert A.; Lee, Si Y.; Fowley, Mark D.; Poirier, Michael R. [Savannah River National Laboratory, Aiken. S.C., 29808 (United States)

    2013-07-01

    Research was completed at Savannah River National Laboratory (SRNL) to investigate processes related to the blending of radioactive, liquid waste, salt solutions in 4920 cubic meter, 25.9 meter diameter storage tanks. One process was the blending of large salt solution batches (up to 1135 - 3028 cubic meters), using submerged centrifugal pumps. A second process was the disturbance of a settled layer of solids, or sludge, on the tank bottom. And a third investigated process was the settling rate of sludge solids if suspended into slurries by the blending pump. To investigate these processes, experiments, CFD models (computational fluid dynamics), and theory were applied. Experiments were performed using simulated, non-radioactive, salt solutions referred to as supernates, and a layer of settled solids referred to as sludge. Blending experiments were performed in a 2.44 meter diameter pilot scale tank, and flow rate measurements and settling tests were performed at both pilot scale and full scale. A summary of the research is presented here to demonstrate the adage that, 'One good experiment fixes a lot of good theory'. Experimental testing was required to benchmark CFD models, or the models would have been incorrectly used. In fact, CFD safety factors were established by this research to predict full-scale blending performance. CFD models were used to determine pump design requirements, predict blending times, and cut costs several million dollars by reducing the number of required blending pumps. This research contributed to DOE missions to permanently close the remaining 47 of 51 SRS waste storage tanks. (authors)

  3. Poly(3-hexylthiophene): TIPS-pentacene blends aiming transistor applications

    Energy Technology Data Exchange (ETDEWEB)

    Silva Ozório, Maiza da, E-mail: ozoriounesp@gmail.com; Nogueira, Gabriel Leonardo; Morais, Rogério Miranda; Silva Martin, Cibely da; Constantino, Carlos José Leopoldo; Alves, Neri

    2016-06-01

    Poly(3-hexylthiophene):6,13-bis(triisopropylsilylethynyl)-pentacene (P3HT:TP) blends with a ratio of 1:1 (wt/wt) were deposited via spin coating on anodized oxide (Al{sub 2}O{sub 3}). A phase separation of the compounds was observed, resulting in the formation of crystalline aggregates of TP molecules that segregate vertically on the surface. The form of segregation depends on the oxide surface treatment used. Spectroscopy analysis shows a higher molecular order of P3HT in the blend than for neat film and that TP molecules are also distributed in the polymeric matrix. Regarding the OFET characteristics, charge carrier mobilities of 1.2 × 10{sup −3} cm{sup 2} V{sup −1} s{sup −1} and 2.0 × 10{sup −3} cm{sup 2} V{sup −1} s{sup −1} were obtained from devices for untreated and (hexamethyldisilazane) HMDS-treated Al{sub 2}O{sub 3} gate dielectric, respectively. These results confirm that P3HT:TP blends have good potential as an active layer in organic field effect transistors (OFETs). - Highlights: • Phase separation occurs in the P3HT:TP blend. • The P3HT:TP blends form aggregates that segregate vertically to the surface. • The molecular order of the P3HT is higher for the blend than for the neat film. • Treatment of surface with HMDS influence in the formation of the aggregate • The P3HT:TP blends have great viability of using for application in transistors.

  4. Low-Temperature Miscibility of Ethanol-Gasoline-Water Blends in Flex Fuel Applications

    DEFF Research Database (Denmark)

    Johansen, T.; Schramm, Jesper

    2009-01-01

    The miscibility of blends of gasoline and hydrous ethanol was investigated experimentally at - 25 degrees C and - 2 degrees C. Furthermore, the maximum water content was found for ethanol in flex fuel blends. The results strongly indicate that blends containing ethanol with a water content above...... that of the ethanol/water azeotrope (4.4% water by mass) can be used as Flex Fuel blends together with gasoline at ambient temperatures of 25 degrees C and 2 degrees C, without phase separation occurring. Additionally, it was shown that the ethanol purity requirement of ethanol-rich flex fuel blends falls...... with increasing ethanol content in the gasoline-rich flex fuel blend....

  5. Effect of irradiation on the prevulcanized latex/low nitrosamines latex blends

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, Pairu; Zin, Wan Manshol Wan [Malaysian Nuclear Agency, 43000 kajang, Selangor (Malaysia); Daik, Rusli [Faculty of Science and Technology, Universiti Kebangsaan Malaysia,43600 bangi, Selangor (Malaysia)

    2015-09-25

    Radiation Prevulcanized Natural Rubber Latex (RVNRL) was blended with Low Nitrosamines Latex (LNL) at different composition ratio. Methyl Metachrylate (MMA) was added for grafting onto the blended latex. Blended latex was subjected to gamma irradiation at various doses up to 8kGy. The mechanical properties and FTIR analysis were investigated as a function of the blended composition and irradiation dose. It was found that blending at specific ratio and gamma irradiation at specific dose led to significant improvement on the properties of the latex. The optimum mechanical properties was attained at a total blending ratio of 70% RVNRL and 30% of LNL.

  6. Influence of biodiesel blending on physicochemical properties and importance of mathematical model for predicting the properties of biodiesel blend

    International Nuclear Information System (INIS)

    Wakil, M.A.; Kalam, M.A.; Masjuki, H.H.; Atabani, A.E.; Rizwanul Fattah, I.M.

    2015-01-01

    Highlights: • Short identification of selected biodiesel feedstock. • Review of physicochemical properties for blended biodiesel. • Mathematical model for predicting properties of various biodiesel blends. - Abstract: The growing demand for green world serves as one of the most significant challenges of modernization. Requirements like largest usage of energy for modern society as well as demand for friendly milieu create a deep concern in field of research. Biofuels are placed at the peak of the research arena for their underlying benefits as mentioned by multiple researches. Out of a number of vegetable oils, only a few are used commercially for biodiesel production. Due to various limitations of edible oil, non-edible oils are becoming a profitable choice. Till today, very little percentage of biodiesel is used successfully in engine. The research is still continuing for improving the biodiesel usage level. Recently, it is found that the blended biodiesel from more than one feedstock provides better performance in engine. This paper reviews the physicochemical properties of different biodiesel blends obtained from various feedstocks with a view to properly understand the fuel quality. Moreover, a short description of each feedstock is given along with graphical presentation of important properties for various blend percentages from B0 to B100. Finally, mathematical model is formed for predicting various properties of biodiesel blend with the help of different research data by using polynomial curve fitting method. The results obtained from a number of literature based on this work shows that the heating value of biodiesel is about 11% lower than diesel except coconut (14.5% lower) whereas kinematic viscosity is in the range of 4–5.4 mm 2 /s. Flash point of all biodiesels are more than 150 °C, except neem and coconut. Cold flow properties of calophyllum, palm, jatropha, moringa are inferior to others. This would help to determine important properties of

  7. EVA reactive blending with Si–H terminated polysiloxane by carbonyl hydrosilylation reaction: From compatibilised blends to crosslinking networks

    International Nuclear Information System (INIS)

    Bonnet, J.; Bounor-Legaré, V.; Alcouffe, P.; Cassagnau, P.

    2012-01-01

    A new and original method based on carbonyl hydrosilylation was developed to prepare ethylene-vinyl acetate (EVA)/polysiloxane polymer blends. This focused on the addition of hydrogenosilane groups (SiH) from polysiloxane to the carbonyl groups of EVA. The influence of the nature of the polysiloxane on blend properties was investigated by rheology and scanning electron microscopy. Mixing of a low viscosity polysiloxane with a high viscosity EVA matrix produced a two-phase morphology. The occurrence of the hydrosilylation reaction at the EVA/polysiloxane interface promoted a homogenisation of the blend depending on the molar ratio SiH/vinyl acetate groups, [SiH]/[VA], and the viscosity ratio of the blend. Two distinct behaviours were observed. The formation of a crosslinked network under shear was obtained for a low viscosity ratio between polysiloxane and EVA (λ polysiloxane/EVA = 4.0 × 10 −6 ) with a high concentration of SiH groups ([SiH]/[VA] = 0.5), while the formation of a compatibilised blend was observed for high molar mass polysiloxanes (Mn > 15,000 g mol −1 ) with a low concentration of SiH ([SiH]/[VA] −3 ). -- Highlights: ► Carbonyl hydrosilylation reaction was found to enhance EVA/polysiloxane immiscible blends. ► EVA crosslinking was obtained with a low molar mass polysiloxane. ► EVA compatibilisation was obtained with a high molar mass polysiloxane. ► Shear rate was found to improve the hydrosilylation reaction at the interface. ► A two-phase morphology of the blends was observed after reaction with fine polysiloxane nodules.

  8. Blended Refuge and Insect Resistance Management for Insecticidal Corn

    Science.gov (United States)

    Crespo, Andre L B; Pan, Zaiqi; Crain, Philip R; Thompson, Stephen D; Pilcher, Clinton D; Sethi, Amit

    2018-01-01

    Abstract In this review, we evaluate the intentional mixing or blending of insecticidal seed with refuge seed for managing resistance by insects to insecticidal corn (Zea mays). We first describe the pest biology and farming practices that will contribute to weighing trade-offs between using block refuges and blended refuges. Case studies are presented to demonstrate how the trade-offs will differ in different systems. We compare biological aspects of several abstract models to guide the reader through the history of modeling, which has played a key role in the promotion or denigration of blending in various scientific debates about insect resistance management for insecticidal crops. We conclude that the use of blended refuge should be considered on a case-by-case basis after evaluation of insect biology, environment, and farmer behavior. For Diabrotica virgifera virgifera, Ostrinia nubilalis, and Helicoverpa zea in the United States, blended refuge provides similar, if not longer, delays in the evolution of resistance compared to separate block refuges. PMID:29220481

  9. How to Mix the Ingredients for a Blended Course Recipe

    Directory of Open Access Journals (Sweden)

    Antoanela Naaji

    2015-12-01

    Full Text Available Over the last years, the growing ubiquity of Social Media, the emerging mobile technologies and the augmented reality become more deeply integrated into the teaching-learning process and also create new opportunities for reinventing the way in which educational actors both perceive and access learning. The major challenges in education that involve tremendous development and innovation are blended courses/ flipped classrooms integrating Social Media (SM, Open Educational Resources (OER and Massive Open Online Courses (MOOC (Johnson et al., 2014. This paper focuses on evaluating the e-learning experiences of various actors in the Romanian educational system. There is a tendency to use virtual learning environments with increasing frequency in higher education, many participants experiencing both online and blended courses. Another issue approached in this paper concerns the relevance of the components of online/ blended courses. In this context, the paper analyzes the importance of these elements with respect to various fields, such as: exact sciences, social sciences, humanistic studies, medical sciences, etc. In conclusion, we identify the most relevant elements in the development of online/ blended courses for various domains. The results will emphasize the standards required for evaluating the quality of online and blended courses.

  10. blend4php: a PHP API for galaxy.

    Science.gov (United States)

    Wytko, Connor; Soto, Brian; Ficklin, Stephen P

    2017-01-01

    Galaxy is a popular framework for execution of complex analytical pipelines typically for large data sets, and is a commonly used for (but not limited to) genomic, genetic and related biological analysis. It provides a web front-end and integrates with high performance computing resources. Here we report the development of the blend4php library that wraps Galaxy's RESTful API into a PHP-based library. PHP-based web applications can use blend4php to automate execution, monitoring and management of a remote Galaxy server, including its users, workflows, jobs and more. The blend4php library was specifically developed for the integration of Galaxy with Tripal, the open-source toolkit for the creation of online genomic and genetic web sites. However, it was designed as an independent library for use by any application, and is freely available under version 3 of the GNU Lesser General Public License (LPGL v3.0) at https://github.com/galaxyproject/blend4phpDatabase URL: https://github.com/galaxyproject/blend4php. © The Author(s) 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

  11. Performance of Diesel Engine Using Blended Crude Jatropha Oil

    Science.gov (United States)

    Kamarudin, Kamarul Azhar; Mohd Sazali, Nor Shahida Akma; Mohd Ali, Mas Fauzi; Alimin, Ahmad Jais; Khir, Saffiah Abdullah

    2010-06-01

    Vegetable oil presents a very promising alternative to diesel oil since it is renewable and has similar properties to the diesel. In view of this, crude jatropha oil is selected and its viscosity is reduced by blending it with diesel. Since jatropha oil has properties which are similar to mineral diesel, it can be used in compression ignition engines without any engine modification. This paper presents the results of investigation carried out on a four-cylinder, four strokes and indirect-injection diesel engine. The engine, operated using composition blends of crude jatropha oil and diesel, were compared with mineral diesel. An experimental investigation has been carried out to analyze the performance characteristics of a compression ignition engine from the blended fuel (5%, 10%, 20% and 30%). A naturally aspirated four-stroke indirect injection diesel engine was tested at full load conditions, speeds between 1000 and 3500 rpm with intervals of 500 rpm. Results obtained from the measures of torque, power, specific fuel consumptions, thermal efficiency and brake mean effective pressure are nearly the same between blended and diesel fuel. An overall graph shows that the performance of relevant parameters from blended fuel is most likely similar to the performance produced from diesel. The experimental results proved that the use of crude jatropha oil in compression ignition engines is a viable alternative to diesel.

  12. Laboratory Oxidation Stability Study on B10 Biodiesel Blends

    Energy Technology Data Exchange (ETDEWEB)

    Engelen, B. [and others

    2013-11-15

    A laboratory oxidation stability study has been completed jointly by CONCAWE and DGMK on three biodiesel blends containing 10% v/v (B10) Fatty Acid Methyl Ester (FAME). The results of the study are compared to measurements from an in-vehicle storage stability study on similar B10 diesel fuels that had been conducted previously in a Joint Industry Study. This laboratory study monitored the oxidation stability of the three B10 blends during six weeks of laboratory storage under ambient (25C) and elevated temperature (43C) conditions. Various test methods were used to monitor oxidation stability changes in the B10 diesel fuel blends including electrical conductivity, viscosity, Rancimat oxidation stability (EN 15751), PetroOxy oxidation stability (EN 16091), acid number (EN 14104), Delta Total Acid Number (Delta TAN), and peroxide number (ISO 3960). Elemental analyses by ICP were also completed on the FAME and B10 blends at the start and end of the laboratory study. The concentrations of dissolved metals were very low in all cases except for silicon which was found to be between about 600-700 ppb in the B10 blends. A limited study was also conducted on one neat FAME sample (B100) to investigate the effect of air/oxygen exposure on the rate of decrease in oxidation stability.

  13. Toughening mechanisms in interfacially modified HDPE/thermoplastic starch blends.

    Science.gov (United States)

    Taguet, Aurélie; Bureau, Martin N; Huneault, Michel A; Favis, Basil D

    2014-12-19

    The mechanical behavior of polymer blends containing 80 wt% of HDPE and 20 wt% of TPS and compatibilized with HDPE-g-MA grafted copolymer was investigated. Unmodified HDPE/TPS blends exhibit high fracture resistance, however, the interfacial modification of those blends by addition of HDPE-g-MA leads to a dramatic drop in fracture resistance. The compatibilization of HDPE/TPS blends increases the surface area of TPS particles by decreasing their size. It was postulated that the addition of HDPE-g-MA induces a reaction between maleic anhydride and hydroxyl groups of the glycerol leading to a decrease of the glycerol content in the TPS phase. This phenomenon increases the stiffness of the modified TPS particles and stiffer TPS particles leading to an important reduction in toughness and plastic deformation, as measured by the EWF method. It is shown that the main toughening mechanism in HDPE/TPS blends is shear-yielding. This article demonstrates that stiff, low diameter TPS particles reduce shear band formation and consequently decrease the resistance to crack propagation. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. Pedagogical and Design Aspects of a Blended Learning Course

    Directory of Open Access Journals (Sweden)

    Karen Precel, Yoram Eshet-Alkalai, Yael Alberton

    2009-04-01

    Full Text Available Based on recent research reports, the blended learning model, which combines face-to-face and online learning, is now the preferred model for online course design. Its superiority over online learning, which lacks face-to-face interaction, is evident from studies that examined both student achievement and satisfaction. Nevertheless, there is ambiguity in the literature and in the field regarding the proper implementation of blended learning and the optimal proportions between online and F2F components in various learning scenarios. The range of contradictory reports in recent literature on the potential of different blended learning models shows the need for more research on specific blended learning courses in order to establish proper standards for effective course design and implementation. The present evaluation study focuses on students’ perceptions of pedagogical and design issues related to a new model for blended learning used in a graduate-level course at the Open University of Israel. Fifty-eight of the course’s 91 students participated in the study and completed a questionnaire regarding three major aspects of the course design: (1 pedagogy, (2 textbook format (print vs. digital, and (3 learning environment usability. The results illustrate the importance of completing the pedagogical and visual design of online learning in advance. Also, the course model suggests ways to bridge the gaps between students and instructors and students and their peers, which are typical of online learning in general and of open universities in particular.

  15. Physical stability of API/polymer-blend amorphous solid dispersions.

    Science.gov (United States)

    Lehmkemper, Kristin; Kyeremateng, Samuel O; Bartels, Mareike; Degenhardt, Matthias; Sadowski, Gabriele

    2018-03-01

    The preparation of amorphous solid dispersions (ASDs) is a well-established strategy for formulating active pharmaceutical ingredients by embedding them in excipients, usually amorphous polymers. Different polymers can be combined for designing ASDs with desired properties like an optimized dissolution behavior. One important criterion for the development of ASD compositions is the physical stability. In this work, the physical stability of API/polymer-blend ASDs was investigated by thermodynamic modeling and stability studies. Amorphous naproxen (NAP) and acetaminophen (APAP) were embedded in blends of hydroxypropyl methylcellulose acetate succinate (HPMCAS) and either poly(vinylpyrrolidone) (PVP) or poly(vinylpyrrolidone-co-vinyl acetate) (PVPVA64). Parameters for modeling the API solubility in the blends and the glass-transition temperature curves of the water-free systems with Perturbed-Chain Statistical Associating Fluid Theory and Kwei equation, respectively, were correlated to experimental data. The phase behavior for standardized storage conditions (0%, 60% and 75% relative humidity (RH)) was predicted and compared to six months-long stability studies. According to modeling and experimental results, the physical stability was reduced with increasing HPMCAS content and increasing RH. This trend was observed for all investigated systems, with both APIs (NAP and APAP) and both polymer blends (PVP/HPMCAS and PVPVA64/HPMCAS). PC-SAFT and the Kwei equation turned out to be suitable tools for modeling and predicting the physical stability of the investigated API/polymer-blends ASDs. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Homogeneity of blended nuclear fuel powders after pneumatic transport

    International Nuclear Information System (INIS)

    Smeltzer, E.E.; Skriba, M.C.; Lyon, W.L.

    1982-01-01

    A study of the pneumatic transport of fine (approx. 1μm) cohesive nuclear fuel powders was conducted for the U.S. Department of Energy to demonstrate the feasibility of this method of transport and to develop a design data base for use in a large scale nuclear fuel production facility. As part of this program, a considerable effort was directed at following the homogeneity of blended powders. Since different reactors require different enrichments, blending and subsequent transport are critical parts of the fabrication sequence. The various materials used represented analogs of a wide range of powders and blends that could be expected in a commercial mixed oxide fabrication facility. All UO 2 powders used were depleted and a co-precipitated master mix of (U, Th)O 2 was made specifically for this program, using thorium as an analog for plutonium. In order to determine the effect of pneumatic transport on a blended powder, samples were taken from a feeder vessel before each test, and from a receiver vessel and a few line sections after each transfer test. The average difference between the before and after degree of non-homogeneity was < 1%, for the 21 tests considered. This shows that overall, the pneumatic transport of blended, fine nuclear fuel powders is possible, with only minor unblending occurring

  17. Viscoelastic properties of PLA/PCL blends compatibilized with different methods

    Science.gov (United States)

    Shin, Boo Young; Han, Do Hung

    2017-11-01

    The aim of this study was to observe changes in the viscoelastic properties of PLA/PCL (80/20) blends produced using different compatibilization methods. Reactive extrusion and high-energy radiation methods were used for blend compatibilization. Storage and loss moduli, complex viscosity, transient stress relaxation modulus, and tan δ of blends were analyzed and blend morphologies were examined. All compatibilized PLA/PCL blends had smaller dispersed particle sizes than the non-compatibilized blend, and well compatibilized blends had finer morphologies than poorly compatibilized blends. Viscoelastic properties differentiated well compatibilized and poorly compatibilized blends. Well compatibilized blends had higher storage and loss moduli and complex viscosities than those calculated by the log-additive mixing rule due to strong interfacial adhesion, whereas poorly compatibilized blends showed negative deviations due to weak interfacial adhesion. Moreover, well compatibilized blends had much slower stress relaxation than poorly compatibilized blends and didn't show tan δ plateau region caused by slippage at the interface between continuous and dispersed phases.

  18. Silk fibroin membranes from solvent-crystallized silk fibroin/gelatin blends: Effects of blend and solvent composition

    Energy Technology Data Exchange (ETDEWEB)

    Gil, Eun S. [Fiber and Polymer Science Program, North Carolina State University, Raleigh, NC 27695 (United States); Frankowski, David J. [Department of Chemical and Biomolecular Engineering, North Carolina State University, Raleigh, NC 27695 (United States); Hudson, Samuel M. [Fiber and Polymer Science Program, North Carolina State University, Raleigh, NC 27695 (United States); Spontak, Richard J. [Department of Chemical and Biomolecular Engineering, North Carolina State University, Raleigh, NC 27695 (United States) and Department of Materials Science and Engineering, North Carolina State University, Raleigh, NC 27695 (United States)]. E-mail: Rich_Spontak@ncsu.edu

    2007-04-15

    Protein membranes have been prepared by mixing gelatin (G) with Bombyx mori silk fibroin (SF) and using aqueous methanol (MeOH) to induce SF crystallization. Amorphous blends of these polymers appear quasi-homogeneous, as discerned from visual observation, electron microscopy and Fourier-transform infrared (FTIR) spectroscopy. Upon subsequent exposure to aqueous MeOH, SF undergoes a conformational change from random-coil to {beta}-sheet. This transformation occurs in pure SF, as well as in each of the G/SF blends, as discerned from FTIR spectroscopy and thermal calorimetry. The influence of MeOH-induced SF crystallization on structure and property development has been measured as functions of blend and solvent composition. By preserving a support scaffold above the G helix-to-coil transition temperature, the formation of crystalline SF networks in G/SF blends can be used to stabilize G-based hydrogels or generate SF membranes for biomaterial, pharmaceutical and gas-separation purposes. The present study not only examines the properties of G/SF blends before and after SF crystallization, but also establishes the foundation for future research into thermally-responsive G/SF bioconjugates.

  19. Preparation and characterization of blends containing silk fibroin and chitosan

    International Nuclear Information System (INIS)

    Moraes, Mariana A. de; Nogueira, Grinia M.; Weska, Raquel F.; Beppu, Marisa M.

    2009-01-01

    The aim of this study was to prepare and characterize blend membranes of silk fibroin and chitosan. Moreover, a conformation of fibroin to a more stable form induced by the addition of chitosan was verified. Blend membranes of fibroin/chitosan were prepared in different proportions and had their crystallinity, structural conformation and thermal stability characterized. The results of crystallographic analysis (XRD) indicated the tendency to higher structural organization caused by the addition of chitosan. FTIR showed that, mainly in a content of chitosan of only 25%, fibroin is present in a more stable form. Thermal analyzes indicate that fibroin is thermally stable and that when its proportion in the blend increases, the temperature in which the degradation is initiated also does so. (author)

  20. Photophysics of charge transfer in a polyfluorene/violanthrone blend

    Science.gov (United States)

    Cabanillas-Gonzalez, J.; Virgili, T.; Lanzani, G.; Yeates, S.; Ariu, M.; Nelson, J.; Bradley, D. D. C.

    2005-01-01

    We present a study of the photophysical and photovoltaic properties of blends of violanthrone in poly[9, 9-bis (2-ethylhexyl)-fluorene-2, 7-diyl ] (PF2/6) . Photoluminescence quenching and photocurrent measurements show moderate efficiencies for charge generation, characteristic of such polymer/dye blends. Pump-probe measurements on blend films suggest that while ˜47% of the total exciton population dissociates within 4ps of photoexcitation, only ˜32% subsequently results in the formation of dye anions. We attribute the discrepancy to the likely formation of complex species with long lifetimes, such as stabilized interface charge pairs or exciplexes. This conclusion is supported by the appearance of a long lifetime component of 2.4ns in the dynamics of the photoinduced absorption signal associated to polarons in photoinduced absorption bands centered at 560nm .