Understanding the Benefits and Limitations of Increasing Maximum Rotor Tip Speed for Utility-Scale Wind Turbines

Science.gov (United States)

Ning, A.; Dykes, K.

2014-06-01

For utility-scale wind turbines, the maximum rotor rotation speed is generally constrained by noise considerations. Innovations in acoustics and/or siting in remote locations may enable future wind turbine designs to operate with higher tip speeds. Wind turbines designed to take advantage of higher tip speeds are expected to be able to capture more energy and utilize lighter drivetrains because of their decreased maximum torque loads. However, the magnitude of the potential cost savings is unclear, and the potential trade-offs with rotor and tower sizing are not well understood. A multidisciplinary, system-level framework was developed to facilitate wind turbine and wind plant analysis and optimization. The rotors, nacelles, and towers of wind turbines are optimized for minimum cost of energy subject to a large number of structural, manufacturing, and transportation constraints. These optimization studies suggest that allowing for higher maximum tip speeds could result in a decrease in the cost of energy of up to 5% for land-based sites and 2% for offshore sites when using current technology. Almost all of the cost savings are attributed to the decrease in gearbox mass as a consequence of the reduced maximum rotor torque. Although there is some increased energy capture, it is very minimal (less than 0.5%). Extreme increases in tip speed are unnecessary; benefits for maximum tip speeds greater than 100-110 m/s are small to nonexistent.

Reliable, Lightweight Transmissions For Off-Shore, Utility Scale Wind Turbines

Energy Technology Data Exchange (ETDEWEB)

Jean-Claude Ossyra

2012-10-25

The objective of this project was to reduce the technical risk for a hydrostatic transmission based drivetrain for high-power utility-size wind turbines. A theoretical study has been performed to validate the reduction of cost of energy (CoE) for the wind turbine, identify risk mitigation strategies for the drive system and critical components, namely the pump, shaft connection and hydrostatic transmission (HST) controls and address additional benefits such as reduced deployment costs, improved torque density and improved mean time between repairs (MTBR).

Utilizing the Intercultural Effectiveness Scale (IES) to Enhance International Student Travel

Science.gov (United States)

Bates, Alicia; Rehal, Dalia Atef

2017-01-01

This paper highlights how one institution used the International Effectiveness Scale (IES) to support intercultural exploration and development for short-term undergraduate travel programs. Authors discuss utilization of the IES to explore students' intercultural development, how it can be applied to create an individualized action plan, and how…

First International Workshop on Grid Simulator Testing of Wind Turbine Drivetrains: Workshop Proceedings

Energy Technology Data Exchange (ETDEWEB)

Gevorgian, V.; Link, H.; McDade, M.; Mander, A.; Fox, J. C.; Rigas, N.

2013-11-01

This report summarizes the proceedings of the First International Workshop on Grid Simulator Testing of Wind Turbine Drivetrains, held from June 13 to 14, 2013, at the National Renewable Energy Laboratory's National Wind Technology Center, located south of Boulder, Colorado. The workshop was sponsored by the U.S. Department of Energy and cohosted by the National Renewable Energy Laboratory and Clemson University under ongoing collaboration via a cooperative research and development agreement. The purpose of the workshop was to provide a forum to discuss the research, testing needs, and state-of-the-art apparatuses involved in grid compliance testing of utility-scale wind turbine generators. This includes both dynamometer testing of wind turbine drivetrains ('ground testing') and field testing grid-connected wind turbines. Four sessions followed by discussions in which all attendees of the workshop were encouraged to participate comprised the workshop.

Hawaii Utility Integration Initiatives to Enable Wind (Wind HUI) Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Dora Nakafuji; Lisa Dangelmaier; Chris Reynolds

2012-07-15

To advance the state and nation toward clean energy, Hawaii is pursuing an aggressive Renewable Portfolio Standard (RPS), 40% renewable generation and 30% energy efficiency and transportation initiatives by 2030. Additionally, with support from federal, state and industry leadership, the Hawaii Clean Energy Initiative (HCEI) is focused on reducing Hawaii's carbon footprint and global warming impacts. To keep pace with the policy momentum and changing industry technologies, the Hawaiian Electric Companies are proactively pursuing a number of potential system upgrade initiatives to better manage variable resources like wind, solar and demand-side and distributed generation alternatives (i.e. DSM, DG). As variable technologies will continue to play a significant role in powering the future grid, practical strategies for utility integration are needed. Hawaiian utilities are already contending with some of the highest penetrations of renewables in the nation in both large-scale and distributed technologies. With island grids supporting a diverse renewable generation portfolio at penetration levels surpassing 40%, the Hawaiian utilities experiences can offer unique perspective on practical integration strategies. Efforts pursued in this industry and federal collaborative project tackled challenging issues facing the electric power industry around the world. Based on interactions with a number of western utilities and building on decades of national and international renewable integration experiences, three priority initiatives were targeted by Hawaiian utilities to accelerate integration and management of variable renewables for the islands. The three initiatives included: Initiative 1: Enabling reliable, real-time wind forecasting for operations by improving short-term wind forecasting and ramp event modeling capabilities with local site, field monitoring; Initiative 2: Improving operators situational awareness to variable resources via real-time grid condition

Wind energy utilization: A bibliography

Science.gov (United States)

1975-01-01

Bibliography cites documents published to and including 1974 with abstracts and references, and is indexed by topic, author, organization, title, and keywords. Topics include: Wind Energy Potential and Economic Feasibility, Utilization, Wind Power Plants and Generators, Wind Machines, Wind Data and Properties, Energy Storage, and related topics.

The International Energy Agency collaboration in wind energy

International Nuclear Information System (INIS)

Beurskens, H.J.M.; Pershagen, B.

1991-07-01

The International Energy Agency (IEA) wind energy agreements have provided a useful framework for international cooperative efforts during more than thirteen years. Nine comprehensive research Tasks have been successfully completed and three Tasks are currently in progress. The sharing of research and information has clearly contributed to the development of wind technology, has eliminated unnecessary redundancy in national programmes, has encouraged utilization of the most efficient approaches to solve common problems, and has created a cooperative spirit among the professional groups that seems to be unique. After a brief introduction on the activities of the IEA on wind energy an overview is given of the ongoing tasks and other current activities with regard to the subject. 1 fig., 5 tabs., 9 refs

Proceedings of the fourth biennial conference and workshop on wind energy conversion systems

Energy Technology Data Exchange (ETDEWEB)

Kottler, Jr., R. J. [ed.

1980-06-01

Separate abstracts are included for papers presented concerning research and development requirements and utility interface and institutional issues for small-scale systems; design requirements and research and development requirements for large-scale systems; economic and operational requirements of large-scale wind systems; wind characteristics and wind energy siting; international activities; wind energy applications in agriculture; federal commercialization and decentralization plans; and wind energy innovative systems.

Comparative analysis of the scales of wind speed Saffir-Simpson y Rodriguez Ramirez

International Nuclear Information System (INIS)

Blanco Heredia, R.; Llanes Buron, C.

2013-01-01

The work consists on a comparative analysis of the scales of intensity of wind internationally well-known Saffir-Simpson and the proposed scale of the carbon investigator Dr. Mario E. Rodriguez Ramirez and their use in the studies of risks for extreme winds, carrying out, the authors a proposal of use of this scale modified that they make them more compatible with the practical reality for the work to architectonic scale. The importance of the article resides in that the carried out proposal tries of femonstrating the pertinent and effective that is the application of the Cuban scale, without gets lost the importance that has as international scale the Saffir-Simpson, in its application in the studies of risks for extreme winds in any region of the basin of Great Caribbean. (Author)

Operating Reserves and Wind Power Integration: An International Comparison; Preprint

Energy Technology Data Exchange (ETDEWEB)

Milligan, M.; Donohoo, P.; Lew, D.; Ela, E.; Kirby, B.; Holttinen, H.; Lannoye, E.; Flynn, D.; O' Malley, M.; Miller, N.; Eriksen, P. B.; Gottig, A.; Rawn, B.; Gibescu, M.; Lazaro, E. G.; Robitaille, A.; Kamwa, I.

2010-10-01

This paper provides a high-level international comparison of methods and key results from both operating practice and integration analysis, based on an informal International Energy Agency Task 25: Large-scale Wind Integration.

9{sup th} international workshop on large-scale integration of wind power into power systems as well as on transmission networks for offshore wind power plants. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Betancourt, Uta; Ackermann, Thomas (eds.)

2010-07-01

Within the 9th International Workshop on large-scale integration of wind power into power systems as well as on transmission networks for offshore wind power plants at 18th to 19th October, 2010 in Quebec (Canada), lectures and poster papers were presented to the following themes: (1) Keynote session and panel; (2) European grid integration studies; (3) Modeling; (4) Wind forecasting; (5) North American grid integration studies; (6) Voltage stability and control; (7) Grid codes and impact studies; (8) Canadian University research (WESNet); (9) Operation and dispatch; (9) Offshore wind power plants; (10) Frequency Control; (11) Methodologies to estimate wind power impacts on power systems, summaries from IEAWIND collaboration; (12) HVDC; (13) Grid codes and system impact studies; (14) Modeling and validation; (15) Regulations, markets and offshore wind energy; (16) Integration issues; (17) Wind turbine control system; (18) Energy management and IT solutions.

Economic assessment of the engineering basis for wind power: Perspective of a vertically integrated utility

International Nuclear Information System (INIS)

Roy, Sanjoy

2009-01-01

If wind park configurations are globally coordinated across the service area of a power utility, then electricity can be generated for the grid with substantial cost advantages. Based on this premise, the paper introduces a model by which large scale assessment of grid connected wind based power generation may be undertaken for a utility service area. The model can be useful to the policy maker for decisions regarding suitable wind portfolio standards (WPS) definition. The utility, on the other hand, may use the model to study its service area for prospective wind based generation. Aspects of the problem modelled include cost-of-energy from individual generating units, daily load variations for the utility with emphasis on limited penetration, features of wind at prospective installation sites, makes of wind energy conversion systems (WECS) available, and recovery of expenditure through revenue. Application of the model to an assessment exercise for the state of Andhra Pradesh (India) is presented as an example. (author)

Gravo-Aeroelastic Scaling for Extreme-Scale Wind Turbines

Energy Technology Data Exchange (ETDEWEB)

Fingersh, Lee J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Loth, Eric [University of Virginia; Kaminski, Meghan [University of Virginia; Qin, Chao [University of Virginia; Griffith, D. Todd [Sandia National Laboratories

2017-06-09

A scaling methodology is described in the present paper for extreme-scale wind turbines (rated at 10 MW or more) that allow their sub-scale turbines to capture their key blade dynamics and aeroelastic deflections. For extreme-scale turbines, such deflections and dynamics can be substantial and are primarily driven by centrifugal, thrust and gravity forces as well as the net torque. Each of these are in turn a function of various wind conditions, including turbulence levels that cause shear, veer, and gust loads. The 13.2 MW rated SNL100-03 rotor design, having a blade length of 100-meters, is herein scaled to the CART3 wind turbine at NREL using 25% geometric scaling and blade mass and wind speed scaled by gravo-aeroelastic constraints. In order to mimic the ultralight structure on the advanced concept extreme-scale design the scaling results indicate that the gravo-aeroelastically scaled blades for the CART3 are be three times lighter and 25% longer than the current CART3 blades. A benefit of this scaling approach is that the scaled wind speeds needed for testing are reduced (in this case by a factor of two), allowing testing under extreme gust conditions to be much more easily achieved. Most importantly, this scaling approach can investigate extreme-scale concepts including dynamic behaviors and aeroelastic deflections (including flutter) at an extremely small fraction of the full-scale cost.

Baseload, industrial-scale wind power: An alternative to coal in China

Energy Technology Data Exchange (ETDEWEB)

Lew, D.J.; Williams, R.H. [Princeton Univ., Princeton, NJ (United States); Xie Shaoxiong; Zhang Shihui [Ministry of Electric Power, Beijing (China)

1996-12-31

This report presents a novel strategy for developing wind power on an industrial-scale in China. Oversized wind farms, large-scale electrical storage and long-distance transmission lines are integrated to deliver {open_quotes}baseload wind power{close_quotes} to distant electricity demand centers. The prospective costs for this approach to developing wind power are illustrated by modeling an oversized wind farm at Huitengxile, Inner Mongolia. Although storage adds to the total capital investment, it does not necessarily increase the cost of the delivered electricity. Storage makes it possible to increase the capacity factor of the electric transmission system, so that the unit cost for long-distance transmission is reduced. Moreover, baseload wind power is typically more valuable to the electric utility than intermittent wind power, so that storage can be economically attractive even in instances where the cost per kWh is somewhat higher than without storage. 9 refs., 3 figs., 2 tabs.

Implementing wind forecasting at a utility

Energy Technology Data Exchange (ETDEWEB)

Landberg, L.; Hansen, M.A.; Vesterager, K.; Bergstroem, W.

1997-03-01

This report describes a project - funded by the Danish Ministry of Energy and the Environment - that has as its aim to implement prediction of the power produced by wind farms in the daily planning at the Danish utility ELKRAFT. The predictions are generated from forecasts from HIRLAM (HIgh Resolution Limited Area Model) of the Danish Meteorological Institute. These predictions are then made valid at individual sites (wind farms) by applying either a matrix generated by the sub-models of WA{sup s}P (Wind Atlas Application and Analysis Program) or by use of a Kalman filter. In the project 17 wind farms have been selected for study. The farms are located on the Zealand and Bornholm islands and all belonging to the Danish utility ELKRAFT. (au) 10 tabs., 65 ills., 14 refs.

Enhancing consumers' voluntary use of small-scale wind turbines to generate own electricity in South Africa

OpenAIRE

Brendan Whelan; Edwin Muchapondwa

2009-01-01

This paper investigates whether South African households and small businesses can take advantage of the country’s substantial wind resources to produce their own power from small-scale wind turbines in a viable way. The viability of small-scale wind turbines is assessed by means of a financial analysis based on the internal rate of return method. The recently announced wind feed-in tariff will not affect the viability of consumer-based small-scale wind turbines considered in this paper sinc...

Distributed small-scale wind in New Zealand: Advantages, barriers and policy support instruments

International Nuclear Information System (INIS)

Barry, Martin; Chapman, Ralph

2009-01-01

If future climate change goals being negotiated internationally are to have any chance of being achieved, developed countries need to undertake a major transition in their energy systems. This will require a rapid expansion of renewable energy generation, including wind electricity. Wind energy in New Zealand is commercially viable in many cases, yet opportunities for its exploitation are far from fully utilised. Many communities are showing resistance to wind farm developments, since large wind farms are often seen as intrusive. Building wind farms on a small scale may be a useful way of overcoming this problem. This study examines the pattern of recent wind industry development in New Zealand. It is argued that two key characteristics have emerged that are limiting the potential development of the industry: a trend towards large scale, leading to increased local opposition; and a small number of investors. Research methods include a review of international and local literature, and a rural mail survey questionnaire, with 338 respondents. We provide survey evidence that small wind farms, and community ownership of them, may be attractive to local communities, and that this point of advantage is helpful for the rapid expansion of wind generation in New Zealand.

Sixth international wind-diesel workshop

International Nuclear Information System (INIS)

1992-01-01

At a workshop on hybrid wind/diesel power generation systems, papers were presented on international research programs, demonstration projects, wind/diesel deployment strategies and requirements, wind/diesel market development and economics, wind turbine design requirements, and wind/diesel models and analytical tools. Separate abstracts have been prepared for 11 papers from this workshop

Sixth international wind-diesel workshop

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

At a workshop on hybrid wind/diesel power generation systems, papers were presented on international research programs, demonstration projects, wind/diesel deployment strategies and requirements, wind/diesel market development and economics, wind turbine design requirements, and wind/diesel models and analytical tools. Separate abstracts have been prepared for 11 papers from this workshop.

Where, when and how much wind is available? A provincial-scale wind resource assessment for China

International Nuclear Information System (INIS)

He, Gang; Kammen, Daniel M.

2014-01-01

China's wind installed capacity has grown at a remarkable rate, over 80% annually average growth since 2005, reaching 91.5 GW of capacity by end of 2013, accounting for over 27% of global capacity. This rapid growth has been the result of a domestic manufacturing base and favorable national policies. Further evolution will be greatly aided with a detailed wind resource assessment that incorporates spatial and temporal variability across China. We utilized 200 representative locations for which 10 years of hourly wind speed data exist to develop provincial capacity factors from 2001 to 2010, and to build analytic wind speed profiles. From these data and analysis we find that China's annual wind generation could reach 2000 TWh to 3500 TWh. Nationally this would correspond to an average capacity factor of 0.18. The diurnal and seasonal variation shows spring and winter has better wind resources than in the summer and fall. A highly interconnected and coordinated power system is needed to effectively exploit this large but variable resource. A full economic assessment of exploitable wind resources demands a larger, systems-level analysis of China's energy options, for which this work is a core requirement. - Highlights: • We assessed China's wind resources by utilizing 10 years of hourly wind speed data of 200 sites. • We built provincial scale wind speed profiles and develop provincial capacity factors for China. • We found that China's wind generation could reach 2000 TWh to 3500 TWh annually. • We observed similar temporal variation pattern of wind availability across China

Siting guidelines for utility application of wind turbines. Final report

Energy Technology Data Exchange (ETDEWEB)

Pennell, W.T.

1983-01-01

Utility-oriented guidelines are described for identifying viable sites for wind turbines. Topics and procedures are also discussed that are important in carrying out a wind turbine siting program. These topics include: a description of the Department of Energy wind resource atlases; procedures for predicting wind turbine performance at potential sites; methods for analyzing wind turbine economics; procedures for estimating installation and maintenance costs; methods for anlayzing the distribution of wind resources over an area; and instrumentation for documenting wind behavior at potential sites. The procedure described is applicable to small and large utilities. Although the procedure was developed as a site-selection tool, it can also be used by a utility who wishes to estimate the potential for wind turbine penetration into its future generation mix.

3. International Workshop on Transmission Networks for Offshore Wind Farms. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Ackermann, T [ed.

2002-07-01

The emphasis is on both theoretical discussions and on practical applications. After almost a decade with mainly demonstration projects in the area of offshore wind power, this year will see the first large commercial offshore wind projects with more than 50 MW installed capacity and more and more larger projects are scheduled for the coming years. Also more and more energy policy makers, electric utilities as well as the media recognize the enormous potential of offshore wind power as a large-scale sustainable energy source. The development in this area results in new ideas, questions and research proposals. Such a new topic is, hydrogen production using offshore wind farms.

Evaluation model of wind energy resources and utilization efficiency of wind farm

Science.gov (United States)

Ma, Jie

2018-04-01

Due to the large amount of abandoned winds in wind farms, the establishment of a wind farm evaluation model is particularly important for the future development of wind farms In this essay, consider the wind farm's wind energy situation, Wind Energy Resource Model (WERM) and Wind Energy Utilization Efficiency Model(WEUEM) are established to conduct a comprehensive assessment of the wind farm. Wind Energy Resource Model (WERM) contains average wind speed, average wind power density and turbulence intensity, which assessed wind energy resources together. Based on our model, combined with the actual measurement data of a wind farm, calculate the indicators using the model, and the results are in line with the actual situation. We can plan the future development of the wind farm based on this result. Thus, the proposed establishment approach of wind farm assessment model has application value.

Proceedings of the International Conference on Wind Energy in Remote Regions

International Nuclear Information System (INIS)

Gipe, P.; Brudny, J.F.; Ilinca, A.; Bouchard, Y.; Proulx, P.; Chaumel, J.L.; Brunelle, M.T.; Henin, S.; Beaudoin, P.; Poirier, N.; Belanger, M.

2005-01-01

This international conference focused on the growth opportunities for the wind power industry in Canada, with particular focus on Quebec and eastern Canada. The conference presented formal paper sessions dealing with the largest wind turbine technology to the smallest machines. It also included tutorials, site visits, case studies and commercial exhibits aimed at wind power developers, utility managers, manufacturers, sub-contractors, theoreticians and practitioners. Participants discussed the best and innovative solutions for the efficient regional development of wind power with particular focus on remote, off-grid applications such as isolated northern communities and islands. The presentations emphasized how wind energy can allow isolated communities to reduce their dependence on costly imported diesel fuel by combining modern electronics with wind turbines and diesel power systems. Environmental impacts and future innovations in wind technology were also discussed along with practical solutions for combining wind energy with other sources of energy. The conference featured 30 presentations, of which 18 have been catalogued separately for inclusion in this database. (author)

Utilization of excess wind power in electric vehicles

International Nuclear Information System (INIS)

Hennings, Wilfried; Mischinger, Stefan; Linssen, Jochen

2013-01-01

This article describes the assessment of future wind power utilization for charging electric vehicles (EVs) in Germany. The potential wind power production in the model years 2020 and 2030 is derived by extrapolating onshore wind power generation and offshore wind speeds measured in 2007 and 2010 to the installed onshore and offshore wind turbine capacities assumed for 2020 and 2030. The energy consumption of an assumed fleet of 1 million EVs in 2020 and 6 million in 2030 is assessed using detailed models of electric vehicles, real world driving cycles and car usage. It is shown that a substantial part of the charging demand of EVs can be met by otherwise unused wind power, depending on the amount of conventional power required for stabilizing the grid. The utilization of wind power is limited by the charging demand of the cars and the bottlenecks in the transmission grid. -- Highlights: •Wind power available for charging depends on minimum required conventional power (must-run). •With 20 GW must-run power, 50% of charging can be met by excess wind power. •Grid bottlenecks decrease charging met by wind power from 50 % to 30 %. •With zero must-run power, only very little wind power is available for charging

Spatial correlation of atmospheric wind at scales relevant for large scale wind turbines

Science.gov (United States)

Bardal, L. M.; Sætran, L. R.

2016-09-01

Wind measurements a short distance upstream of a wind turbine can provide input for a feedforward wind turbine controller. Since the turbulent wind field will be different at the point/plane of measurement and the rotor plane the degree of correlation between wind speed at two points in space both in the longitudinal and lateral direction should be evaluated. This study uses a 2D array of mast mounted anemometers to evaluate cross-correlation of longitudinal wind speed. The degree of correlation is found to increase with height and decrease with atmospheric stability. The correlation is furthermore considerably larger for longitudinal separation than for lateral separation. The integral length scale of turbulence is also considered.

Results of large scale wind climatologically estimations

Directory of Open Access Journals (Sweden)

Andrea Kircsi

2008-05-01

Full Text Available The aim of this article is to describe theparticular field of climatology which analyzes airmovement characteristics regarding utilization of windfor energy generation. The article describes features ofwind energy potential available in Hungary compared towind conditions in other areas of the northern quartersphere in order to assist the wind energy use developmentin Hungary. Information on wind climate gives a solidbasis for financial and economic decisions ofstakeholders in the field of wind energy utilization.

Wind energy in Denmark and within the Elsam utility area

International Nuclear Information System (INIS)

Friis, P.; Grauballe, J.

1995-01-01

At the turn of 1994, 3,700 wind turbines, with a total installed capacity of 540 MW were connected to the Danish utility grid. In 1994 these turbines fed 1,118 GWh wind energy into the grid, corresponding to approximately 3.3% of the total electricity consumption. The ELSAM utility area supplies the electric energy consumed by half the Danish population. The area has a large wind energy potential and approx. 75% of the installed wind energy capacity in Denmark is situated here accounting for 400 MW. In 1994 the ELSAM utilities supplied a total of 18,450 GWh with wind power contributing 850 GWh, i.e. 4.6% of the ELSAM sales to the consumers. (Author)

Optimal Capacity Allocation of Large-Scale Wind-PV-Battery Units

Directory of Open Access Journals (Sweden)

Kehe Wu

2014-01-01

Full Text Available An optimal capacity allocation of large-scale wind-photovoltaic- (PV- battery units was proposed. First, an output power model was established according to meteorological conditions. Then, a wind-PV-battery unit was connected to the power grid as a power-generation unit with a rated capacity under a fixed coordinated operation strategy. Second, the utilization rate of renewable energy sources and maximum wind-PV complementation was considered and the objective function of full life cycle-net present cost (NPC was calculated through hybrid iteration/adaptive hybrid genetic algorithm (HIAGA. The optimal capacity ratio among wind generator, PV array, and battery device also was calculated simultaneously. A simulation was conducted based on the wind-PV-battery unit in Zhangbei, China. Results showed that a wind-PV-battery unit could effectively minimize the NPC of power-generation units under a stable grid-connected operation. Finally, the sensitivity analysis of the wind-PV-battery unit demonstrated that the optimization result was closely related to potential wind-solar resources and government support. Regions with rich wind resources and a reasonable government energy policy could improve the economic efficiency of their power-generation units.

Case Studies of Potential Facility-Scale and Utility-Scale Non-Hydro Renewable Energy Projects across Reclamation

Energy Technology Data Exchange (ETDEWEB)

Haase, S.; Burman, K.; Dahle, D.; Heimiller, D.; Jimenez, A.; Melius, J.; Stoltenberg, B.; VanGeet, O.

2013-05-01

This report summarizes the results of an assessment and analysis of renewable energy opportunities conducted for the U.S. Department of the Interior, Bureau of Reclamation by the National Renewable Energy Laboratory. Tasks included assessing the suitability for wind and solar on both a utility and facility scale.

Line Capacity Expansion and Transmission Switching in Power Systems With Large-Scale Wind Power

DEFF Research Database (Denmark)

Villumsen, Jonas Christoffer; Bronmo, Geir; Philpott, Andy B.

2013-01-01

In 2020 electricity production from wind power should constitute nearly 50% of electricity demand in Denmark. In this paper we look at optimal expansion of the transmission network in order to integrate 50% wind power in the system, while minimizing total fixed investment cost and expected cost...... of power generation. We allow for active switching of transmission elements to reduce congestion effects caused by Kirchhoff's voltage law. Results show that actively switching transmission lines may yield a better utilization of transmission networks with large-scale wind power and increase wind power...

Applying micro scales of horizontal axis wind turbines for operation in low wind speed regions

International Nuclear Information System (INIS)

Pourrajabian, Abolfazl; Ebrahimi, Reza; Mirzaei, Masoud

2014-01-01

Highlights: • Three micro-turbines with output power less than 1 kW were designed for operation in low wind speed regions. • In addition to the output power, starting time was considered as a key parameter during the design. • The effects of generator resistive torque and number of blades on the performance of the turbines were investigated. - Abstract: Utilizing the micro scales of wind turbines could noticeably supply the demand for the electricity in low wind speed regions. Aerodynamic design and optimization of the blade, as a main part of a wind turbine, were addressed in the study. Three micro scales of horizontal axis wind turbines with output power of 0.5, 0.75 and 1 kW were considered and the geometric optimization of the blades in terms of the two involved parameters, chord and twist, was undertaken. In order to improve the performance of the turbines at low wind speeds, starting time was included in an objective function in addition to the output power – the main and desirable goal of the wind turbine blade design. A purpose-built genetic algorithm was employed to maximize both the output power and the starting performance which were calculated by the blade-element momentum theory. The results emphasize that the larger values of the chord and twist at the root part of the blades are indispensable for the better performance when the wind speed is low. However, the noticeable value of the generator resistive torque could largely delay the starting of the micro-turbines especially for the considered smaller size, 0.5 kW, where the starting aerodynamic torque could not overcome the generator resistive torque. For that size, an increase in the number of blades improved both the starting performance and also output power

Wind direction variations in the natural wind – A new length scale

DEFF Research Database (Denmark)

Johansson, Jens; Christensen, Silas Sverre

2018-01-01

During an observation period of e.g. 10min, the wind direction will differ from its mean direction for short periods of time, and a body of air will pass by from that direction before the direction changes once again. The present paper introduces a new length scale which we have labeled the angular...... length scale. This length scale expresses the average size of the body of air passing by from any deviation of wind direction away from the mean direction. Using metrological observations from two different sites under varying conditions we have shown that the size of the body of air relative to the mean...... size decreases linearly with the deviation from the mean wind direction when the deviation is normalized with the standard deviation of the wind direction. It is shown that this linear variation is independent of the standard deviation of the wind direction, and that the two full-scale data sets follow...

Full scale measurement of wind induced pressures : 1 configuration of wind induced pressures

NARCIS (Netherlands)

Geurts, C.P.W.; Wijen, H.L.M.

1994-01-01

A research project 10 the spectral characteristics of wind induced pressures is in progress in Eindhoven. This project includes both wind tunnel and full scale measurements. Wind induced pressures are measured in full scale at the main building of Eindhoven University of Technology. This paper

Wind energy utilization: A bibliography with abstracts - Cumulative volume 1944/1974

Science.gov (United States)

1975-01-01

Bibliography, up to 1974 inclusive, of articles and books on utilization of wind power in energy generation. Worldwide literature is surveyed, and short abstracts are provided in many cases. The citations are grouped by subject: (1) general; (2) utilization; (3) wind power plants; (4) wind power generators (rural, synchronous, remote station); (5) wind machines (motors, pumps, turbines, windmills, home-built); (6) wind data and properties; (7) energy storage; and (8) related topics (control and regulation devices, wind measuring devices, blade design and rotors, wind tunnel simulation, aerodynamics). Gross-referencing is aided by indexes of authors, corporate sources, titles, and keywords.

design of a small scale wind generator for low wind speed areas

African Journals Online (AJOL)

USER

Most small scale level wind turbine generators are directly driven system, variable speed, and partially ... the best solutions for small-scale wind power plants. Low-speed multi-pole PM generators ..... Designs of the Same Magnet Structure for.

Utility-sized Madaras wind plants

Science.gov (United States)

Whitford, D. H.; Minardi, J. E.

1981-01-01

An analysis and technological updating were conducted for the Madaras Rotor Power Plant concept, to determine its ability to compete both technically and economically with horizontal axis wind turbine generators currently under development. The Madaras system uses large cylinders rotating vertically atop each regularly spaced flatcar of a train to propel them, by means of Magnus-effect interaction with the wind, along a circular or oval track. Alternators geared to the wheels of each car generate electrical power, which is transmitted to a power station by a trolley system. The study, consisting of electromechanical design, wind tunnel testing, and performance and cost analyses, shows that utility-sized plants greater than 228 MW in capacity and producing 975,000 kWh/year are feasible. Energy costs for such plants are projected to be between 22% lower and 12% higher than horizontal axis turbine plants of comparable output.

Wind energy development: Danish experiences and international options

International Nuclear Information System (INIS)

Frandsen, S.; Hasted, F.; Josephsen, L.; Nielson, J.H.

1989-01-01

In Denmark, wind energy makes a visible contribution to energy planning. Since 1976, over 1,800 wind turbine units have been installed in Denmark, representing a capacity of ca 140 MW out of a grid capacity of 8,000 MW. These units are all grid-connected and the unit sizes range from 55 kW to 400 kW. The installed wind energy capacity represents a substantial development of technologies for wind energy utilization during the last 15 years, involving participation from research institutes, electric utilities, private industry, and the national energy administration. A considerable improvement of the technical and economic performance of wind turbines, along with increased reliability and durability, has been strongly supported by comprehensive government programs. In 1985, another large construction program was initiated which will add 100 MW wind power capacity by the end of 1990. Parallel with commercial development, Danish utilities have developed and constructed a number of megawatt-size wind turbines on a pilot basis. In general terms the wind energy resources in Denmark are rather good, and many suitable sites exist, but installed wind energy capacity is limited by the high population density. Consequently, research is being conducted on the feasibility of offshore wind turbines. In other countries, wind energy developments similar to those in Denmark are taking place. In communities with no connection to the national grid, special attention should be paid to hybrid systems such as wind-diesel and hydro-wind systems. A substantial transfer of technology is required for facilitating significant development of hybrid systems in developing countries. 11 refs., 7 figs., 2 tabs

Potential climatic impacts and reliability of very large-scale wind farms

Directory of Open Access Journals (Sweden)

C. Wang

2010-02-01

Full Text Available Meeting future world energy needs while addressing climate change requires large-scale deployment of low or zero greenhouse gas (GHG emission technologies such as wind energy. The widespread availability of wind power has fueled substantial interest in this renewable energy source as one of the needed technologies. For very large-scale utilization of this resource, there are however potential environmental impacts, and also problems arising from its inherent intermittency, in addition to the present need to lower unit costs. To explore some of these issues, we use a three-dimensional climate model to simulate the potential climate effects associated with installation of wind-powered generators over vast areas of land or coastal ocean. Using wind turbines to meet 10% or more of global energy demand in 2100, could cause surface warming exceeding 1 °C over land installations. In contrast, surface cooling exceeding 1 °C is computed over ocean installations, but the validity of simulating the impacts of wind turbines by simply increasing the ocean surface drag needs further study. Significant warming or cooling remote from both the land and ocean installations, and alterations of the global distributions of rainfall and clouds also occur. These results are influenced by the competing effects of increases in roughness and decreases in wind speed on near-surface turbulent heat fluxes, the differing nature of land and ocean surface friction, and the dimensions of the installations parallel and perpendicular to the prevailing winds. These results are also dependent on the accuracy of the model used, and the realism of the methods applied to simulate wind turbines. Additional theory and new field observations will be required for their ultimate validation. Intermittency of wind power on daily, monthly and longer time scales as computed in these simulations and inferred from meteorological observations, poses a demand for one or more options to ensure

Scaling forecast models for wind turbulence and wind turbine power intermittency

Science.gov (United States)

Duran Medina, Olmo; Schmitt, Francois G.; Calif, Rudy

2017-04-01

The intermittency of the wind turbine power remains an important issue for the massive development of this renewable energy. The energy peaks injected in the electric grid produce difficulties in the energy distribution management. Hence, a correct forecast of the wind power in the short and middle term is needed due to the high unpredictability of the intermittency phenomenon. We consider a statistical approach through the analysis and characterization of stochastic fluctuations. The theoretical framework is the multifractal modelisation of wind velocity fluctuations. Here, we consider three wind turbine data where two possess a direct drive technology. Those turbines are producing energy in real exploitation conditions and allow to test our forecast models of power production at a different time horizons. Two forecast models were developed based on two physical principles observed in the wind and the power time series: the scaling properties on the one hand and the intermittency in the wind power increments on the other. The first tool is related to the intermittency through a multifractal lognormal fit of the power fluctuations. The second tool is based on an analogy of the power scaling properties with a fractional brownian motion. Indeed, an inner long-term memory is found in both time series. Both models show encouraging results since a correct tendency of the signal is respected over different time scales. Those tools are first steps to a search of efficient forecasting approaches for grid adaptation facing the wind energy fluctuations.

PREDICTION OF POWER GENERATION OF SMALL SCALE VERTICAL AXIS WIND TURBINE USING FUZZY LOGIC

Directory of Open Access Journals (Sweden)

Altab Hossain

2009-01-01

Full Text Available Renewable energy from the wind turbine has been focused for the alternative source of power generation due to the following advances of the of the wind turbine. Firstly, the wind turbine is highly efficient and eco-friendly. Secondly, the turbine has the ability to response for the changeable power generation based on the wind velocity and structural framework. However, the competitive efficiency of the wind turbine is necessary to successfully alternate the conventional power sources. The most relevant factor which affects the overall efficiency of the wind turbine is the wind velocity and the relative turbine dimensions. Artificial intelligence systems are widely used technology that can learn from examples and are able to deal with non-linear problems. Compared with traditional approach, fuzzy logic approach is more efficient for the representation, manipulation and utilization. Therefore, the primary purpose of this work was to investigate the relationship between wind turbine power generation and wind velocity, and to illustrate how fuzzy expert system might play an important role in prediction of wind turbine power generation. The main purpose of the measurement over the small scaled prototype vertical axis wind turbine for the wind velocity is to predict the performance of full scaled H-type vertical axis wind turbine. Prediction of power generation at the different wind velocities has been tested at the Thermal Laboratory of Faculty of Engineering, Universiti Industri Selangor (UNISEL and results concerning the daily prediction have been obtained.

PREDICTION OF POWER GENERATION OF SMALL SCALE VERTICAL AXIS WIND TURBINE USING FUZZY LOGIC

Directory of Open Access Journals (Sweden)

Altab Md. Hossain

2009-12-01

Full Text Available Renewable energy from the wind turbine has been focused for the alternative source of power generation due to the following advances of the of the wind turbine. Firstly, the wind turbine is highly efficient and eco-friendly. Secondly, the turbine has the ability to response for the changeable power generation based on the wind velocity and structural framework. However, the competitive efficiency of the wind turbine is necessary to successfully alternate the conventional power sources. The most relevant factor which affects the overall efficiency of the wind turbine is the wind velocity and the relative turbine dimensions. Artificial intelligence systems are widely used technology that can learn from examples and are able to deal with non-linear problems. Compared with traditional approach, fuzzy logic approach is more efficient for the representation, manipulation and utilization. Therefore, the primary purpose of this work was to investigate the relationship between wind turbine power generation and wind velocity, and to illustrate how fuzzy expert system might play an important role in prediction of wind turbine power generation. The main purpose of the measurement over the small scaled prototype vertical axis wind turbine for the wind velocity is to predict the performance of full scaled H-type vertical axis wind turbine. Prediction of power generation at the different wind velocities has been tested at the Thermal Laboratory of Faculty of Engineering, Universiti Industri Selangor (UNISEL and results concerning the daily prediction have been obtained.

Assessment of Global Wind Energy Resource Utilization Potential

Science.gov (United States)

Ma, M.; He, B.; Guan, Y.; Zhang, H.; Song, S.

2017-09-01

Development of wind energy resource (WER) is a key to deal with climate change and energy structure adjustment. A crucial issue is to obtain the distribution and variability of WER, and mine the suitable location to exploit it. In this paper, a multicriteria evaluation (MCE) model is constructed by integrating resource richness and stability, utilization value and trend of resource, natural environment with weights. The global resource richness is assessed through wind power density (WPD) and multi-level wind speed. The utilizable value of resource is assessed by the frequency of effective wind. The resource stability is assessed by the coefficient of variation of WPD and the frequency of prevailing wind direction. Regression slope of long time series WPD is used to assess the trend of WER. All of the resource evaluation indicators are derived from the atmospheric reanalysis data ERA-Interim with spatial resolution 0.125°. The natural environment factors mainly refer to slope and land-use suitability, which are derived from multi-resolution terrain elevation data 2010 (GMTED 2010) and GlobalCover2009. Besides, the global WER utilization potential map is produced, which shows most high potential regions are located in north of Africa. Additionally, by verifying that 22.22 % and 48.8 9% operational wind farms fall on medium-high and high potential regions respectively, the result can provide a basis for the macroscopic siting of wind farm.

Next Generation Wind Turbine

Energy Technology Data Exchange (ETDEWEB)

Cheraghi, S. Hossein [Western New England Univ., Springfield, MA (United States); Madden, Frank [FloDesign Wind Turbine Corp., Waltham, MA (United States)

2012-09-01

The goal of this collaborative effort between Western New England University's College of Engineering and FloDesign Wind Turbine (FDWT) Corporation to wok on a novel areodynamic concept that could potentially lead to the next generation of wind turbines. Analytical studies and early scale model tests of FDWT's Mixer/Ejector Wind Turbine (MEWT) concept, which exploits jet-age advanced fluid dynamics, indicate that the concept has the potential to significantly reduce the cost of electricity over conventional Horizontal Axis Wind Turbines while reducing land usage. This project involved the design, fabrication, and wind tunnel testing of components of MEWT to provide the research and engineering data necessary to validate the design iterations and optimize system performance. Based on these tests, a scale model prototype called Briza was designed, fabricated, installed and tested on a portable tower to investigate and improve the design system in real world conditions. The results of these scale prototype efforts were very promising and have contributed significantly to FDWT's ongoing development of a product scale wind turbine for deployment in multiple locations around the U.S. This research was mutually beneficial to Western New England University, FDWT, and the DOE by utilizing over 30 student interns and a number of faculty in all efforts. It brought real-world wind turbine experience into the classroom to further enhance the Green Engineering Program at WNEU. It also provided on-the-job training to many students, improving their future employment opportunities, while also providing valuable information to further advance FDWT's mixer-ejector wind turbine technology, creating opportunities for future project innovation and job creation.

Wind energy systems. Application to regional utilities

Energy Technology Data Exchange (ETDEWEB)

1979-06-01

This study developed a generic planning process that utilities can use to determine the feasibility of utilizing WECS (Wind Energy Conversion Systems) as part of their future mix of equipment. While this is primarily an economic process, other questions dealing with WECS availability, capacity credit, operating reserve, performance of WECS arrays, etc., had to be addressed. The approach was to establish the worth, or breakeven value, of WECS to the utility and to determine the impact that WECS additions would have on the utilities mix of conventional source.

Wind and Solar Curtailment: International Experience and Practices

DEFF Research Database (Denmark)

Lew, Debra; Bird, Lori; Milligan, Michael

2013-01-01

High penetrations of wind and solar generation on power systems are resulting in increasing curtailment. Wind and solar integration studies predict increased curtailment as penetration levels grow. This paper examines experiences with curtailment on bulk power systems internationally. It discusses...... how much curtailment is occurring, how it is occurring, why it is occurring, and what is being done to reduce curtailment. This summary is produced as part of the International Energy Agency Wind Task 25 on Design and Operation of Power Systems with Large Amounts of Wind Power....

The economics and environmental impacts of large-scale wind power in a carbon constrained world

Science.gov (United States)

Decarolis, Joseph Frank

increase as wind is developed on a large scale. Finally, this thesis summarizes collaborative work utilizing general circulation models to determine whether wind turbines have an impact of climate. The results suggest that the climatic impact is non-negligible at continental scales, but further research is warranted.

Residents' Perceptions toward Utility-Scale Wind Farm Development

Science.gov (United States)

Campbell, Joseph; Romich, Eric

2015-01-01

Increased development of wind farms in the U.S. has fostered debates surrounding the siting and support for the projects. Prior research demonstrates the importance of understanding the attitudes and opinions of community members when developing projects. This article reviews a case study of an Ohio community that integrated a local survey to…

Unsteady aerodynamics simulation of a full-scale horizontal axis wind turbine using CFD methodology

International Nuclear Information System (INIS)

Cai, Xin; Gu, Rongrong; Pan, Pan; Zhu, Jie

2016-01-01

Highlights: • A full-scale HAWT is simulated under operational conditions of wind shear and yaw. • The CFD method and sliding mesh are adopted to complete the calculation. • Thrust and torque of blades reach the peak and valley at the same time in wind shear. • The wind turbine produces yaw moment during the whole revolution in yaw case. • The torques and thrusts of the three blades present cyclical changes. - Abstract: The aerodynamic performance of wind turbines is significantly influenced by the unsteady flow around the rotor blades. The research on unsteady aerodynamics for Horizontal Axis Wind Turbines (HAWTs) is still poorly understood because of the complex flow physics. In this study, the unsteady aerodynamic configuration of a full-scale HAWT is simulated with consideration of wind shear, tower shadow and yaw motion. The calculated wind turbine which contains tapered tower, rotor overhang and tilted rotor shaft is constructed by making reference of successfully commercial operated wind turbine designed by NEG Micon and Vestas. A validated CFD method is utilized to analyze unsteady aerodynamic characteristics which affect the performance on such a full-scale HAWT. The approach of sliding mesh is used to carefully deal with the interface between static and moving parts in the flow field. The annual average wind velocity and wind profile in the atmospheric border are applied as boundary conditions. Considering the effects of wind shear and tower shadow, the simulation results show that the each blade reaches its maximum and minimum aerodynamic loads almost at the same time during the rotation circle. The blade–tower interaction imposes great impact on the power output performance. The wind turbine produces yaw moment during the whole revolution and the maximum aerodynamic loads appear at the upwind azimuth in the yaw computation case.

Measuring and modelling of the wind on the scale of tall wind turbines

DEFF Research Database (Denmark)

Floors, Rogier Ralph

The air flow in the lower atmosphere on the spatial scale of the modern wind turbines is studied. Because wind turbines are nowadays often taller than 100 m, the validity of current analytical and numerical atmospheric models has to be evaluated and more knowledge about the structure of the atmos......The air flow in the lower atmosphere on the spatial scale of the modern wind turbines is studied. Because wind turbines are nowadays often taller than 100 m, the validity of current analytical and numerical atmospheric models has to be evaluated and more knowledge about the structure...

Efficient utilization of wind power: Long-distance transmission or local consumption?

Science.gov (United States)

Sun, Yuanzhang; Ma, Xiyuan; Xu, Jian; Bao, Yi; Liao, Siyang

2017-09-01

Excess wind power produced in wind-intensive areas is normally delivered to remote load centers via long-distance transmission lines. This paper presents a comparison between long-distance transmission, which has gained popularity, and local energy consumption, in which a fraction of the generated wind power can be locally consumed by energy-intensive industries. First, the challenges and solutions to the long-distance transmission and local consumption of wind power are presented. Then, the two approaches to the utilization of wind power are compared in terms of system security, reliability, cost, and capability to utilize wind energy. Finally, the economic feasibility and technical feasibility of the local consumption of wind power are demonstrated by a large and isolated industrial power system, or supermicrogrid, in China. The coal-fired generators together with the short-term interruptible electrolytic aluminum load in the supermicrogrid are able to compensate for the intermittency of wind power. In the long term, the transfer of high-energy-consumption industries to wind-rich areas and their local consumption of the available wind power are beneficial.

Efficient utilization of wind power: Long-distance transmission or local consumption?

Institute of Scientific and Technical Information of China (English)

Yuanzhang SUN; Xiyuan MA; Jian XU; Yi BAO; Siyang LIAO

2017-01-01

Excess wind power produced in wind-intensive areas is normally delivered to remote load centers via long-distance transmission lines.This paper presents a comparison between long-distance transmission,which has gained popularity,and local energy consumption,in which a fraction of the generated wind power can be locally consumed by energy-intensive industries.First,the challenges and solutions to the long-distance transmission and local consumption of wind power are presented.Then,the two approaches to the utilization of wind power are compared in terms of system security,reliability,cost,and capability to utilize wind energy.Finally,the economic feasibility and technical feasibility of the local consumption of wind power are demonstrated by a large and isolated industrial power system,or supermicrogrid,in China.The coal-fired generators together with the shortterm interruptible electrolytic aluminum load in the supermicrogrid are able to compensate for the intermittency of wind power.In the long term,the transfer of highenergy-consumption industries to wind-rich areas and their local consumption of the available wind power are beneficial.

Electric utility application of wind energy conversion systems on the island of Oahu

Energy Technology Data Exchange (ETDEWEB)

Lindley, C.A.; Melton, W.C.

1979-02-23

This wind energy application study was performed by The Aerospace Corporation for the Wind Systems Branch of the Department of Energy. The objective was to identify integration problems for a Wind Energy Conversion System (WECS) placed into an existing conventional utility system. The integration problems included environmental, institutional and technical aspects as well as economic matters, but the emphasis was on the economics of wind energy. The Hawaiian Electric Company utility system on the island of Oahu was selected for the study because of the very real potential for wind energy on that island, and because of the simplicity afforded in analyzing that isolated utility.

Wind Farm Wake Models From Full Scale Data

DEFF Research Database (Denmark)

Knudsen, Torben; Bak, Thomas

2012-01-01

This investigation is part of the EU FP7 project “Distributed Control of Large-Scale Offshore Wind Farms”. The overall goal in this project is to develop wind farm controllers giving power set points to individual turbines in the farm in order to minimise mechanical loads and optimise power. One...... on real full scale data. The modelling is based on so called effective wind speed. It is shown that there is a wake for a wind direction range of up to 20 degrees. Further, when accounting for the wind direction it is shown that the two model structures considered can both fit the experimental data...

An experimental system for release simulation of internal stores in a supersonic wind tunnel

Directory of Open Access Journals (Sweden)

Wei Liu

2017-02-01

Full Text Available Aerodynamic parameters obtained from separation experiments of internal stores in a wind tunnel are significant in aircraft designs. Accurate wind tunnel tests can help to improve the release stability of the stores and in-flight safety of the aircrafts in supersonic environments. A simulative system for free drop experiments of internal stores based on a practical project is provided in this paper. The system contains a store release mechanism, a control system and an attitude measurement system. The release mechanism adopts a six-bar linkage driven by a cylinder, which ensures the release stability. The structure and initial aerodynamic parameters of the stores are also designed and adjusted. A high speed vision measurement system for high speed rolling targets is utilized to measure the pose parameters of the internal store models and an optimizing method for the coordinates of markers is presented based on a priori model. The experimental results show excellent repeatability of the system, and indicate that the position measurement precision is less than 0.13 mm, and the attitude measurement precision for pitch and yaw angles is less than 0.126°, satisfying the requirements of practical wind tunnel tests. A separation experiment for the internal stores is also conducted in the FL-3 wind tunnel of China Aerodynamics Research Institute.

Results from utility wind resource assessment programs in Nebraska, Colorado, and Arizona

Energy Technology Data Exchange (ETDEWEB)

Drapeau, C.L. [Global Energy Concepts, Inc., Bothell, WA (United States)

1997-12-31

Global Energy Concepts (GEC) has been retained by utilities in Colorado, Nebraska, and Arizona to site, install, and operate 21 wind monitoring stations as part of the Utility Wind Resource Assessment Program (U*WRAP). Preliminary results indicate wind speed averages at 40 meters (132 ft) of 6.5 - 7.4 m/s (14.5-16.5 mph) in Nebraska and 7.6 - 8.9 m/s (17.0-19.9 mph) in Colorado. The Arizona stations are not yet operational. This paper presents the history and current status of the 21 monitoring stations as well as preliminary data results. Information on wind speeds, wind direction, turbulence intensity, wind shear, frequency distribution, and data recovery rates are provided.

Proceedings of the International Conference on Wind Energy in Remote Regions; Actes du Colloque International sur Energie Eolienne et Site Eloignes

Energy Technology Data Exchange (ETDEWEB)

Gipe, P.; Brudny, J.F.; Ilinca, A.; Bouchard, Y.; Proulx, P.; Chaumel, J.L.; Brunelle, M.T.; Henin, S.; Beaudoin, P.; Poirier, N.; Belanger, M. [Quebec Univ., Rimouski, PQ (Canada). WERR Organizational Committee

2005-07-01

This international conference focused on the growth opportunities for the wind power industry in Canada, with particular focus on Quebec and eastern Canada. The conference presented formal paper sessions dealing with the largest wind turbine technology to the smallest machines. It also included tutorials, site visits, case studies and commercial exhibits aimed at wind power developers, utility managers, manufacturers, sub-contractors, theoreticians and practitioners. Participants discussed the best and innovative solutions for the efficient regional development of wind power with particular focus on remote, off-grid applications such as isolated northern communities and islands. The presentations emphasized how wind energy can allow isolated communities to reduce their dependence on costly imported diesel fuel by combining modern electronics with wind turbines and diesel power systems. Environmental impacts and future innovations in wind technology were also discussed along with practical solutions for combining wind energy with other sources of energy. The conference featured 30 presentations, of which 18 have been catalogued separately for inclusion in this database. refs., tabs., figs.

Wind as a utility-grade supply resource: A planning framework for the Pacific Northwest

International Nuclear Information System (INIS)

Johnson, M.S.; Litchfield, J.

1993-12-01

Many areas throughout the United States possess favorable wind resources that, as yet, remain undeveloped. This paper provides valuable information on the type of information developers can provide, utility interpretation of the information in regard to electric energy and capacity attributes, and wind resource characteristics of interest to utilities. The paper also reviews key utility planning contexts within which prospective wind resources may be evaluated

Design and preliminary testing of a MEMS microphone phased array for aeroacoustic testing of a small-scale wind turbine airfoil

Energy Technology Data Exchange (ETDEWEB)

Bale, A.; Orlando, S.; Johnson, D. [Waterloo Univ., ON (Canada). Wind Energy Group

2010-07-01

One of the barriers preventing the widespread utilization of wind turbines is the audible sound that they produce. Developing quieter wind turbines will increase the amount of available land onto which wind farms can be built. Noise emissions from wind turbines can be attributed to the aerodynamic effects between the turbine blades and the air surrounding them. A dominant source of these aeroacoustic emissions from wind turbines is known to originate at the trailing edges of the airfoils. This study investigated the flow physics of noise generation in an effort to reduce noise from small-scale wind turbine airfoils. The trailing edge noise was studied on scale-models in wind tunnels and applied to full scale conditions. Microphone phased arrays are popular research tools in wind tunnel aeroacoustic studies because they can measure and locate noise sources. However, large arrays of microphones can be prohibitively expensive. This paper presented preliminary testing of micro-electrical mechanical system (MEMS) microphones in phased arrays for aeroacoustic testing on a small wind turbine airfoil. Preliminary results showed that MEMS microphones are an acceptable low-cost alternative to costly condenser microphones. 19 refs., 1 tab., 11 figs.

An investigation of the utility scale wind energy for north‐eastern ...

African Journals Online (AJOL)

In the present study, the wind energy potential for Garissa (0°28S, 39°38'E) and Marsabit (2° 19N, 37° 58'E), both rural towns in north-eastern Kenya have been statistically analyzed on a 6-year measured hourly time series wind speed data. The probability distribution parameters are derived the time series data and the ...

Northeast Utilities' participation in the Kaman/NASA wind power program

Science.gov (United States)

Lotker, M.

1975-01-01

The role of Northeast Utilities in the Kaman/NASA large wind generator study is reviewed. The participation falls into four principal areas: (1) technical assistance; (2) economic analysis; (3) applications; and (4) institutional and legal. A model for the economic viability of wind power is presented.

Effects of Net Metering on the Use of Small-Scale Wind Systems in the United States

Energy Technology Data Exchange (ETDEWEB)

Forsyth, T. L.; Pedden, M.; Gagliano, T.

2002-11-01

Factors such as technological advancements, steadily decreasing costs, consumer demand, and state and federal policies are combining to make wind energy the world's fastest growing energy source. State and federal policies are facilitating the growth of the domestic, large-scale wind power market; however, small-scale wind projects (those with a capacity of less than 100 kilowatts[kW]) still face challenges in many states. Net metering, also referred to as net billing, is one particular policy that states are implementing to encourage the use of small renewable energy systems. Net metering allows individual, grid-tied customers who generate electricity using a small renewable energy system to receive credit from their utility for any excess power they generate beyond what they consume. Under most state rules, residential, commercial, and industrial customers are eligible for net metering; however, some states restrict eligibility to particular customer classes. This paper illustrates how net metering programs in certain states vary considerably in terms of how customers are credited for excess power they generate; the type and size of eligible technologies and whether the utility; the state, or some other entity administers the program. This paper focuses on10 particular states where net metering policies are in place. It analyzes how the different versions of these programs affect the use of small-scale wind technologies and whether some versions are more favorable to this technology than others. The choice of citizens in some states to net meter with photovoltaics is also examined.

Wind power impacts and electricity storage - a time scale perspective

DEFF Research Database (Denmark)

Hedegaard, Karsten; Meibom, Peter

2012-01-01

Integrating large amounts of wind power in energy systems poses balancing challenges due to the variable and only partly predictable nature of wind. The challenges cover different time scales from intra-hour, intra-day/day-ahead to several days and seasonal level. Along with flexible electricity...... demand options, various electricity storage technologies are being discussed as candidates for contributing to large-scale wind power integration and these also differ in terms of the time scales at which they can operate. In this paper, using the case of Western Denmark in 2025 with an expected 57% wind...... power penetration, wind power impacts on different time scales are analysed. Results show consecutive negative and high net load period lengths indicating a significant potential for flexibility measures capable of charging/activating demand and discharging/inactivating demand in periods of 1 h to one...

77 FR 75984 - Utility Scale Wind Towers From the Socialist Republic of Vietnam: Final Determination of Sales at...

Science.gov (United States)

2012-12-26

... Determination 1. Steel Plate 2. Surrogate Financial Statements 3. Financial Ratio Adjustments 4. Packed Weight... financial statements for Ganges International Pvt Ltd. for purposes of calculating the surrogate financial ratios. Scope of the Investigation The merchandise covered by this investigation are certain wind towers...

International wind farm markets: An overview

Energy Technology Data Exchange (ETDEWEB)

Rackstraw, K. [American Wind Energy Association, Washington, DC (United States)

1996-12-31

More wind energy capacity was installed in 1995 than in any previous year. Two markets, Germany and India, accounted for nearly two-thirds of those installations, while the largest single market in the world historically, the US, ground nearly to a halt. Market supports in Germany and India, however, are vulnerable to political forces largely beyond the control of the wind industry. This paper examines the growth of international wind farm markets worldwide and notes that future markets will be more broadly based, leaving the industry less vulnerable to political changes. The paper also concludes that an additional 18,500 MW could be installed by the year 2005 even without assuming a dire ecological scenario that would create environmental drivers to accelerate wind market growth. 4 figs.

What scaling means in wind engineering: Complementary role of the reduced scale approach in a BLWT and the full scale testing in a large climatic wind tunnel

Science.gov (United States)

Flamand, Olivier

2017-12-01

Wind engineering problems are commonly studied by wind tunnel experiments at a reduced scale. This introduces several limitations and calls for a careful planning of the tests and the interpretation of the experimental results. The talk first revisits the similitude laws and discusses how they are actually applied in wind engineering. It will also remind readers why different scaling laws govern in different wind engineering problems. Secondly, the paper focuses on the ways to simplify a detailed structure (bridge, building, platform) when fabricating the downscaled models for the tests. This will be illustrated by several examples from recent engineering projects. Finally, under the most severe weather conditions, manmade structures and equipment should remain operational. What “recreating the climate” means and aims to achieve will be illustrated through common practice in climatic wind tunnel modelling.

Worldwide potential of wind energy

Energy Technology Data Exchange (ETDEWEB)

Flavin, C

1982-01-01

A well-documented discussion is presented dealing with the worldwide potential of wind energy as a source of electrical and mechanical power. It is pointed out that 2% of the solar insolation is converted to wind kinetic energy; it is constantly renewed and nondepletable. Efficiency of windmills are discussed (20 to 40%) and payback periods of less than 5 years are cited. Effects of wind velocity and site location are described. Wind pumps are reviewed and the need for wind pumps, particularly in the developing countries is stressed. The generation of electricity by windmills using small turbines is reviewed and appears promising in areas with wind velocities greater than 12 mi/hr. The development of large windmills and groups of windmills (windfarms) for large scale electrical power is discussed, illustrated, and reviewed (offshore sites included). Environmental and safety problems are considered as well as the role of electrical utilities, government support and research activities. It is concluded that the potential contribution of wind energy is immense and that mechanical windmills may become one of the most important renewable technologies. Electrical generating potential is estimated at 20 to 30% of electrical needs. International programs are discussed briefly. 57 references. (MJJ)

Legal-institutional arrangements facilitating offshore wind energy conversion systems (WECS) utilization. Final report

Energy Technology Data Exchange (ETDEWEB)

Mayo, L.H.

1977-09-01

Concern for the continuing sufficiency of energy supplies in the U.S. has tended to direct increasing attention to unconventional sources of supply, including wind energy. Some of the more striking proposals for the utilization of wind energy relate to offshore configurations. The legal-institutional arrangements for facilitating the utilization of offshore wind energy conversion systems (WECS) are examined by positioning three program alternatives and analyzing the institutional support required for the implementation of each.

Fostering a renewable energy technology industry: an international comparison of wind industry policy support mechanisms

International Nuclear Information System (INIS)

Lewis, J.I.; Wiser, R.H.

2007-01-01

This article examines the importance of national and sub-national policies in supporting the development of successful global wind turbine manufacturing companies. We explore the motivations behind establishing a local wind power industry, and the paths that different countries have taken to develop indigenous large wind turbine manufacturing industries within their borders. This is done through a cross-country comparison of the policy support mechanisms that have been employed to directly and indirectly promote wind technology manufacturing in 12 countries. We find that in many instances there is a clear relationship between a manufacturer's success in its home country market and its eventual success in the global wind power market. Whether new wind turbine manufacturing entrants are able to succeed will likely depend in part on the utilization of their turbines in their own domestic market, which is turn will be influenced by the annual size and stability of that market. Consequently, policies that support a sizable, stable market for wind power, in conjunction with policies that specifically provide incentives for wind power technology to be manufactured locally, are most likely to result in the establishment of an internationally competitive wind industry. (author)

Fostering a renewable energy technology industry: An international comparison of wind industry policy support mechanisms

International Nuclear Information System (INIS)

Lewis, Joanna I.; Wiser, Ryan H.

2007-01-01

This article examines the importance of national and sub-national policies in supporting the development of successful global wind turbine manufacturing companies. We explore the motivations behind establishing a local wind power industry, and the paths that different countries have taken to develop indigenous large wind turbine manufacturing industries within their borders. This is done through a cross-country comparison of the policy support mechanisms that have been employed to directly and indirectly promote wind technology manufacturing in 12 countries. We find that in many instances there is a clear relationship between a manufacturer's success in its home country market and its eventual success in the global wind power market. Whether new wind turbine manufacturing entrants are able to succeed will likely depend in part on the utilization of their turbines in their own domestic market, which in turn will be influenced by the annual size and stability of that market. Consequently, policies that support a sizable, stable market for wind power, in conjunction with policies that specifically provide incentives for wind power technology to be manufactured locally, are most likely to result in the establishment of an internationally competitive wind industry

Wind energy in Europe

International Nuclear Information System (INIS)

Sesto, E.

1992-02-01

Interest in wind energy as a supplementary source for the production of electricity has recently gained renewed momentum due to widespread concern about environmental impacts from the large scale use of fossil fuels and nuclear energy. In addition, political unrest in the Middle East has drawn attention to the importance of national energy self-sufficiency. European government administrations, however, have not yet fully appreciated the real worth of the 'clean energy' afforded by wind energy. In this regard, the European Wind Energy Association (EWEA) is acting as a strong voice to inform the public and energy planners by stimulating international wind energy R ampersand D cooperation, and organizing conferences to explain the advantages of wind energy. In October 1991, EWEA published a strategy document giving a picture of the real possibilities offered by wind energy within the geographical, social, and European economic context. This paper provides an overview of the more significant features to emerge from this document which represents a useful guideline for wind power plant technical/economic feasibility studies in that it contains brief notes on resource availability, land requirements, visual and acoustic impacts, turbine sizing, performance, interconnection to utility grids, maintenance and operating costs, safety, as well as, on marketing aspects

Research on large-scale wind farm modeling

Science.gov (United States)

Ma, Longfei; Zhang, Baoqun; Gong, Cheng; Jiao, Ran; Shi, Rui; Chi, Zhongjun; Ding, Yifeng

2017-01-01

Due to intermittent and adulatory properties of wind energy, when large-scale wind farm connected to the grid, it will have much impact on the power system, which is different from traditional power plants. Therefore it is necessary to establish an effective wind farm model to simulate and analyze the influence wind farms have on the grid as well as the transient characteristics of the wind turbines when the grid is at fault. However we must first establish an effective WTGs model. As the doubly-fed VSCF wind turbine has become the mainstream wind turbine model currently, this article first investigates the research progress of doubly-fed VSCF wind turbine, and then describes the detailed building process of the model. After that investigating the common wind farm modeling methods and pointing out the problems encountered. As WAMS is widely used in the power system, which makes online parameter identification of the wind farm model based on off-output characteristics of wind farm be possible, with a focus on interpretation of the new idea of identification-based modeling of large wind farms, which can be realized by two concrete methods.

Practical strategies of wind energy utilization for uninhabited aerial vehicles in loiter flights

Science.gov (United States)

Singhania, Hong Yang

Uninhabited Aerial Vehicle (UAV) is becoming increasingly attractive in missions where human presence is undesirable or impossible. Agile maneuvers and long endurance are among the most desired advantages of UAVs over aircraft that have human pilots onboard. Past studies suggest that the performance of UAVs may be considerably improved by utilizing natural resources, especially wind energy, during flights. The key challenge of exploiting wind energy in practical UAV operations lies in the availability of reliable and timely wind field information in the operational region. This thesis presents a practical onboard strategy that attempts to over-come this challenge, to enable UAVs in utilizing wind energy effectively during flights, and therefore to enhance performance. We propose and explore a strategy that combines wind measurement and optimal trajectory planning onboard UAVs. During a cycle of a loiter flight, a UAV can take measurements of wind velocity components over the flight region, use these measurements to estimate the local wind field through a model-based approach, and then compute a flight trajectory for the next flight cycle with the objective of optimizing fuel. As the UAV follows the planned trajectory, it continues to measure the wind components and repeats the process of updating the wind model with new estimations and planning optimal trajectories for the next flight cycle. Besides presenting an onboard trajectory planning strategy of wind energy exploration, estimation, and utilization, this research also develops a semi-analytical linearized solution to the formulated nonlinear optimal control problem. Simulations and numerical results indicate that the fuel savings of trajectories generated using the proposed scheme depend on wind speed, wind estimation errors, rates of change in wind speed, and the wind model structures. For a given wind field, the magnitude of potential fuel savings is also contingent upon UAVs' performance capabilities.

Comparative analysis of the scales of wind speed Saffir-Simpson y Rodriguez Ramirez; Analisis comparativo de las escalas de velocidad de viento Saffir-Simpson y Rodriguez Ramirez

Energy Technology Data Exchange (ETDEWEB)

Blanco Heredia, R.; Llanes Buron, C.

2013-06-01

The work consists on a comparative analysis of the scales of intensity of wind internationally well-known Saffir-Simpson and the proposed scale of the carbon investigator Dr. Mario E. Rodriguez Ramirez and their use in the studies of risks for extreme winds, carrying out, the authors a proposal of use of this scale modified that they make them more compatible with the practical reality for the work to architectonic scale. The importance of the article resides in that the carried out proposal tries of demonstrating the pertinent and effective that is the application of the Cuban scale, without gets lost the importance that has as international scale the Saffir-Simpson, in its application in the studies of risks for extreme winds in any region of the basin of Great Caribbean. (Author)

Power Oscillation Damping Controller for Wind Power Plant Utilizing Wind Turbine Inertia as Energy Storage

DEFF Research Database (Denmark)

Knüppel, Thyge; Nielsen, Jørgen Nygård; Jensen, Kim Høj

2011-01-01

For a wind power plant (WPP) the upper limit for active power output is bounded by the instantaneous wind conditions and therefore a WPP must curtail its power output when system services with active power are delivered. Here, a power oscillation damping controller (POD) for WPPs is presented...... that utilizes the stored kinetic energy in the wind turbine (WT) mechanical system as energy storage from which damping power can be exchanged. This eliminates the need for curtailed active power production. Results are presented using modal analysis and induced torque coefficients (ITC) to depict the torques...... induced on the synchronous generators from the POD. These are supplemented with nonlinear time domain simulations with and without an auxiliary POD for the WPP. The work is based on a nonlinear, dynamic model of the 3.6 MW Siemens Wind Power wind turbine....

Energy System Analysis of Large-Scale Integration of Wind Power

International Nuclear Information System (INIS)

Lund, Henrik

2003-11-01

The paper presents the results of two research projects conducted by Aalborg University and financed by the Danish Energy Research Programme. Both projects include the development of models and system analysis with focus on large-scale integration of wind power into different energy systems. Market reactions and ability to exploit exchange on the international market for electricity by locating exports in hours of high prices are included in the analyses. This paper focuses on results which are valid for energy systems in general. The paper presents the ability of different energy systems and regulation strategies to integrate wind power, The ability is expressed by three factors: One factor is the degree of electricity excess production caused by fluctuations in wind and CHP heat demands. The other factor is the ability to utilise wind power to reduce CO 2 emission in the system. And the third factor is the ability to benefit from exchange of electricity on the market. Energy systems and regulation strategies are analysed in the range of a wind power input from 0 to 100% of the electricity demand. Based on the Danish energy system, in which 50 per cent of the electricity demand is produced in CHP, a number of future energy systems with CO 2 reduction potentials are analysed, i.e. systems with more CHP, systems using electricity for transportation (battery or hydrogen vehicles) and systems with fuel-cell technologies. For the present and such potential future energy systems different regulation strategies have been analysed, i.e. the inclusion of small CHP plants into the regulation task of electricity balancing and grid stability and investments in electric heating, heat pumps and heat storage capacity. Also the potential of energy management has been analysed. The results of the analyses make it possible to compare short-term and long-term potentials of different strategies of large-scale integration of wind power

Contribution of large scale coherence to wind turbine power: A large eddy simulation study in periodic wind farms

Science.gov (United States)

Chatterjee, Tanmoy; Peet, Yulia T.

2018-03-01

Length scales of eddies involved in the power generation of infinite wind farms are studied by analyzing the spectra of the turbulent flux of mean kinetic energy (MKE) from large eddy simulations (LES). Large-scale structures with an order of magnitude bigger than the turbine rotor diameter (D ) are shown to have substantial contribution to wind power. Varying dynamics in the intermediate scales (D -10 D ) are also observed from a parametric study involving interturbine distances and hub height of the turbines. Further insight about the eddies responsible for the power generation have been provided from the scaling analysis of two-dimensional premultiplied spectra of MKE flux. The LES code is developed in a high Reynolds number near-wall modeling framework, using an open-source spectral element code Nek5000, and the wind turbines have been modelled using a state-of-the-art actuator line model. The LES of infinite wind farms have been validated against the statistical results from the previous literature. The study is expected to improve our understanding of the complex multiscale dynamics in the domain of large wind farms and identify the length scales that contribute to the power. This information can be useful for design of wind farm layout and turbine placement that take advantage of the large-scale structures contributing to wind turbine power.

Utility Wind Integration and Operating Impact - State of the Art

Energy Technology Data Exchange (ETDEWEB)

Smith, J. C.; Milligan, M. R.; DeMeo, E. A.; Parsons, B.

2007-08-01

At the end of 2005, the Power Engineering Society (PES) published a special issue of its Power & Energy Magazine that focused on integrating wind into the power system. This paper provides a summary and update on many of the salient points from that special issue about the current state of knowledge regarding utility wind integration issues.

Environmental implications of large-scale adoption of wind power: a scenario-based life cycle assessment

International Nuclear Information System (INIS)

Arvesen, Anders; Hertwich, Edgar G

2011-01-01

We investigate the potential environmental impacts of a large-scale adoption of wind power to meet up to 22% of the world’s growing electricity demand. The analysis builds on life cycle assessments of generic onshore and offshore wind farms, meant to represent average conditions for global deployment of wind power. We scale unit-based findings to estimate aggregated emissions of building, operating and decommissioning wind farms toward 2050, taking into account changes in the electricity mix in manufacturing. The energy scenarios investigated are the International Energy Agency’s BLUE scenarios. We estimate 1.7–2.6 Gt CO 2 -eq climate change, 2.1–3.2 Mt N-eq marine eutrophication, 9.2–14 Mt NMVOC photochemical oxidant formation, and 9.5–15 Mt SO 2 -eq terrestrial acidification impact category indicators due to global wind power in 2007–50. Assuming lifetimes 5 yr longer than reference, the total climate change indicator values are reduced by 8%. In the BLUE Map scenario, construction of new capacity contributes 64%, and repowering of existing capacity 38%, to total cumulative greenhouse gas emissions. The total emissions of wind electricity range between 4% and 14% of the direct emissions of the replaced fossil-fueled power plants. For all impact categories, the indirect emissions of displaced fossil power are larger than the total emissions caused by wind power.

Wind speed reductions by large-scale wind turbine deployments lower turbine efficiencies and set low wind power potentials

Science.gov (United States)

Miller, Lee; Kleidon, Axel

2017-04-01

Wind turbines generate electricity by removing kinetic energy from the atmosphere. Large numbers of wind turbines are likely to reduce wind speeds, which lowers estimates of electricity generation from what would be presumed from unaffected conditions. Here, we test how well wind power potentials that account for this effect can be estimated without explicitly simulating atmospheric dynamics. We first use simulations with an atmospheric general circulation model (GCM) that explicitly simulates the effects of wind turbines to derive wind power limits (GCM estimate), and compare them to a simple approach derived from the climatological conditions without turbines [vertical kinetic energy (VKE) estimate]. On land, we find strong agreement between the VKE and GCM estimates with respect to electricity generation rates (0.32 and 0.37 We m-2) and wind speed reductions by 42 and 44%. Over ocean, the GCM estimate is about twice the VKE estimate (0.59 and 0.29 We m-2) and yet with comparable wind speed reductions (50 and 42%). We then show that this bias can be corrected by modifying the downward momentum flux to the surface. Thus, large-scale limits to wind power can be derived from climatological conditions without explicitly simulating atmospheric dynamics. Consistent with the GCM simulations, the approach estimates that only comparatively few land areas are suitable to generate more than 1 We m-2 of electricity and that larger deployment scales are likely to reduce the expected electricity generation rate of each turbine. We conclude that these atmospheric effects are relevant for planning the future expansion of wind power.

Wind Power Forecasting Error Distributions: An International Comparison

DEFF Research Database (Denmark)

Hodge, Bri-Mathias; Lew, Debra; Milligan, Michael

2012-01-01

Wind power forecasting is essential for greater penetration of wind power into electricity systems. Because no wind forecasting system is perfect, a thorough understanding of the errors that may occur is a critical factor for system operation functions, such as the setting of operating reserve...... levels. This paper provides an international comparison of the distribution of wind power forecasting errors from operational systems, based on real forecast data. The paper concludes with an assessment of similarities and differences between the errors observed in different locations....

Status of large scale wind turbine technology development abroad?

Institute of Scientific and Technical Information of China (English)

Ye LI; Lei DUAN

2016-01-01

To facilitate the large scale (multi-megawatt) wind turbine development in China, the foreign e?orts and achievements in the area are reviewed and summarized. Not only the popular horizontal axis wind turbines on-land but also the o?shore wind turbines, vertical axis wind turbines, airborne wind turbines, and shroud wind turbines are discussed. The purpose of this review is to provide a comprehensive comment and assessment about the basic work principle, economic aspects, and environmental impacts of turbines.

Dynamic Reactive Power Compensation of Large Scale Wind Integrated Power System

DEFF Research Database (Denmark)

Rather, Zakir Hussain; Chen, Zhe; Thøgersen, Paul

2015-01-01

wind turbines especially wind farms with additional grid support functionalities like dynamic support (e,g dynamic reactive power support etc.) and ii) refurbishment of existing conventional central power plants to synchronous condensers could be one of the efficient, reliable and cost effective option......Due to progressive displacement of conventional power plants by wind turbines, dynamic security of large scale wind integrated power systems gets significantly compromised. In this paper we first highlight the importance of dynamic reactive power support/voltage security in large scale wind...... integrated power systems with least presence of conventional power plants. Then we propose a mixed integer dynamic optimization based method for optimal dynamic reactive power allocation in large scale wind integrated power systems. One of the important aspects of the proposed methodology is that unlike...

Evaluation of a micro-scale wind model's performance over realistic building clusters using wind tunnel experiments

Science.gov (United States)

Zhang, Ning; Du, Yunsong; Miao, Shiguang; Fang, Xiaoyi

2016-08-01

The simulation performance over complex building clusters of a wind simulation model (Wind Information Field Fast Analysis model, WIFFA) in a micro-scale air pollutant dispersion model system (Urban Microscale Air Pollution dispersion Simulation model, UMAPS) is evaluated using various wind tunnel experimental data including the CEDVAL (Compilation of Experimental Data for Validation of Micro-Scale Dispersion Models) wind tunnel experiment data and the NJU-FZ experiment data (Nanjing University-Fang Zhuang neighborhood wind tunnel experiment data). The results show that the wind model can reproduce the vortexes triggered by urban buildings well, and the flow patterns in urban street canyons and building clusters can also be represented. Due to the complex shapes of buildings and their distributions, the simulation deviations/discrepancies from the measurements are usually caused by the simplification of the building shapes and the determination of the key zone sizes. The computational efficiencies of different cases are also discussed in this paper. The model has a high computational efficiency compared to traditional numerical models that solve the Navier-Stokes equations, and can produce very high-resolution (1-5 m) wind fields of a complex neighborhood scale urban building canopy (~ 1 km ×1 km) in less than 3 min when run on a personal computer.

Characterization of wind velocities in the wake of a full scale wind turbine using three ground-based synchronized WindScanners

DEFF Research Database (Denmark)

Yazicioglu, Hasan; Angelou, Nikolas; Mikkelsen, Torben Krogh

2016-01-01

The wind energy community is in need of detailed full-field measurements in the wake of wind turbines. Here, three dimensional(3D) wind vector field measurements obtained in the near-wake region behind a full-scale test turbine are presented. Specifically, the wake of a NEG Nordtank turbine...

Controllable Grid Interface for Testing Ancillary Service Controls and Fault Performance of Utility-Scale Wind Power Generation: Preprint

Energy Technology Data Exchange (ETDEWEB)

Gevorgian, Vahan; Koralewicz, Przemyslaw; Wallen, Robb; Muljadi, Eduard

2017-02-01

The rapid expansion of wind power has led many transmission system operators to demand modern wind power plants to comply with strict interconnection requirements. Such requirements involve various aspects of wind power plant operation, including fault ride-through and power quality performance as well as the provision of ancillary services to enhance grid reliability. During recent years, the National Renewable Energy Laboratory (NREL) of the U.S. Department of Energy has developed a new, groundbreaking testing apparatus and methodology to test and demonstrate many existing and future advanced controls for wind generation (and other renewable generation technologies) on the multimegawatt scale and medium-voltage levels. This paper describes the capabilities and control features of NREL's 7-MVA power electronic grid simulator (also called a controllable grid interface, or CGI) that enables testing many active and reactive power control features of modern wind turbine generators -- including inertial response, primary and secondary frequency responses, and voltage regulation -- under a controlled, medium-voltage grid environment. In particular, this paper focuses on the specifics of testing the balanced and unbalanced fault ride-through characteristics of wind turbine generators under simulated strong and weak medium-voltage grid conditions. In addition, this paper provides insights on the power hardware-in-the-loop feature implemented in the CGI to emulate (in real time) the conditions that might exist in various types of electric power systems under normal operations and/or contingency scenarios. Using actual test examples and simulation results, this paper describes the value of CGI as an ultimate modeling validation tool for all types of 'grid-friendly' controls by wind generation.

Development and Validation of a Rating Scale for Wind Jazz Improvisation Performance

Science.gov (United States)

Smith, Derek T.

2009-01-01

The purpose of this study was to construct and validate a rating scale for collegiate wind jazz improvisation performance. The 14-item Wind Jazz Improvisation Evaluation Scale (WJIES) was constructed and refined through a facet-rational approach to scale development. Five wind jazz students and one professional jazz educator were asked to record…

Investigation on the integral output power model of a large-scale wind farm

Institute of Scientific and Technical Information of China (English)

BAO Nengsheng; MA Xiuqian; NI Weidou

2007-01-01

The integral output power model of a large-scale wind farm is needed when estimating the wind farm's output over a period of time in the future.The actual wind speed power model and calculation method of a wind farm made up of many wind turbine units are discussed.After analyzing the incoming wind flow characteristics and their energy distributions,and after considering the multi-effects among the wind turbine units and certain assumptions,the incoming wind flow model of multi-units is built.The calculation algorithms and steps of the integral output power model of a large-scale wind farm are provided.Finally,an actual power output of the wind farm is calculated and analyzed by using the practical measurement wind speed data.The characteristics of a large-scale wind farm are also discussed.

Wind/Hybrid Electricity Applications

Energy Technology Data Exchange (ETDEWEB)

McDaniel, Lori [Iowa Department of Natural Resources, Des Moines, IA (United States)

2001-03-01

Wind energy is widely recognized as the most efficient and cost effective form of new renewable energy available in the Midwest. New utility-scale wind farms (arrays of large turbines in high wind areas producing sufficient energy to serve thousands of homes) rival the cost of building new conventional forms of combustion energy plants, gas, diesel and coal power plants. Wind energy is not subject to the inflationary cost of fossil fuels. Wind energy can also be very attractive to residential and commercial electric customers in high wind areas who would like to be more self-sufficient for their energy needs. And wind energy is friendly to the environment at a time when there is increasing concern about pollution and climate change. However, wind energy is an intermittent source of power. Most wind turbines start producing small amounts of electricity at about 8-10 mph (4 meters per second) of wind speed. The turbine does not reach its rated output until the wind reaches about 26-28 mph (12 m/s). So what do you do for power when the output of the wind turbine is not sufficient to meet the demand for energy? This paper will discuss wind hybrid technology options that mix wind with other power sources and storage devices to help solve this problem. This will be done on a variety of scales on the impact of wind energy on the utility system as a whole, and on the commercial and small-scale residential applications. The average cost and cost-benefit of each application along with references to manufacturers will be given. Emerging technologies that promise to shape the future of renewable energy will be explored as well.

Potential climatic impacts and reliability of large-scale offshore wind farms

International Nuclear Information System (INIS)

Wang Chien; Prinn, Ronald G

2011-01-01

The vast availability of wind power has fueled substantial interest in this renewable energy source as a potential near-zero greenhouse gas emission technology for meeting future world energy needs while addressing the climate change issue. However, in order to provide even a fraction of the estimated future energy needs, a large-scale deployment of wind turbines (several million) is required. The consequent environmental impacts, and the inherent reliability of such a large-scale usage of intermittent wind power would have to be carefully assessed, in addition to the need to lower the high current unit wind power costs. Our previous study (Wang and Prinn 2010 Atmos. Chem. Phys. 10 2053) using a three-dimensional climate model suggested that a large deployment of wind turbines over land to meet about 10% of predicted world energy needs in 2100 could lead to a significant temperature increase in the lower atmosphere over the installed regions. A global-scale perturbation to the general circulation patterns as well as to the cloud and precipitation distribution was also predicted. In the later study reported here, we conducted a set of six additional model simulations using an improved climate model to further address the potential environmental and intermittency issues of large-scale deployment of offshore wind turbines for differing installation areas and spatial densities. In contrast to the previous land installation results, the offshore wind turbine installations are found to cause a surface cooling over the installed offshore regions. This cooling is due principally to the enhanced latent heat flux from the sea surface to lower atmosphere, driven by an increase in turbulent mixing caused by the wind turbines which was not entirely offset by the concurrent reduction of mean wind kinetic energy. We found that the perturbation of the large-scale deployment of offshore wind turbines to the global climate is relatively small compared to the case of land

A Wind Power Plant with Thermal Energy Storage for Improving the Utilization of Wind Energy

Directory of Open Access Journals (Sweden)

Chang Liu

2017-12-01

Full Text Available The development of the wind energy industry is seriously restricted by grid connection issues and wind energy generation rejections introduced by the intermittent nature of wind energy sources. As a solution of these problems, a wind power system integrating with a thermal energy storage (TES system for district heating (DH is designed to make best use of the wind power in the present work. The operation and control of the system are described in detail. A one-dimensional system model of the system is developed based on a generic model library using the object-oriented language Modelica for system modeling. Validations of the main components of the TES module are conducted against experimental results and indicate that the models can be used to simulate the operation of the system. The daily performance of the integrated system is analyzed based on a seven-day operation. And the influences of system configurations on the performance of the integrated system are analyzed. The numerical results show that the integrated system can effectively improve the utilization of total wind energy under great wind power rejection.

Examining the utility of satellite-based wind sheltering estimates for lake hydrodynamic modeling

Science.gov (United States)

Van Den Hoek, Jamon; Read, Jordan S.; Winslow, Luke A.; Montesano, Paul; Markfort, Corey D.

2015-01-01

Satellite-based measurements of vegetation canopy structure have been in common use for the last decade but have never been used to estimate canopy's impact on wind sheltering of individual lakes. Wind sheltering is caused by slower winds in the wake of topography and shoreline obstacles (e.g. forest canopy) and influences heat loss and the flux of wind-driven mixing energy into lakes, which control lake temperatures and indirectly structure lake ecosystem processes, including carbon cycling and thermal habitat partitioning. Lakeshore wind sheltering has often been parameterized by lake surface area but such empirical relationships are only based on forested lakeshores and overlook the contributions of local land cover and terrain to wind sheltering. This study is the first to examine the utility of satellite imagery-derived broad-scale estimates of wind sheltering across a diversity of land covers. Using 30 m spatial resolution ASTER GDEM2 elevation data, the mean sheltering height, hs, being the combination of local topographic rise and canopy height above the lake surface, is calculated within 100 m-wide buffers surrounding 76,000 lakes in the U.S. state of Wisconsin. Uncertainty of GDEM2-derived hs was compared to SRTM-, high-resolution G-LiHT lidar-, and ICESat-derived estimates of hs, respective influences of land cover type and buffer width on hsare examined; and the effect of including satellite-based hs on the accuracy of a statewide lake hydrodynamic model was discussed. Though GDEM2 hs uncertainty was comparable to or better than other satellite-based measures of hs, its higher spatial resolution and broader spatial coverage allowed more lakes to be included in modeling efforts. GDEM2 was shown to offer superior utility for estimating hs compared to other satellite-derived data, but was limited by its consistent underestimation of hs, inability to detect within-buffer hs variability, and differing accuracy across land cover types. Nonetheless

Fatigue Analysis of Large-scale Wind turbine

Directory of Open Access Journals (Sweden)

Zhu Yongli

2017-01-01

Full Text Available The paper does research on top flange fatigue damage of large-scale wind turbine generator. It establishes finite element model of top flange connection system with finite element analysis software MSC. Marc/Mentat, analyzes its fatigue strain, implements load simulation of flange fatigue working condition with Bladed software, acquires flange fatigue load spectrum with rain-flow counting method, finally, it realizes fatigue analysis of top flange with fatigue analysis software MSC. Fatigue and Palmgren-Miner linear cumulative damage theory. The analysis result indicates that its result provides new thinking for flange fatigue analysis of large-scale wind turbine generator, and possesses some practical engineering value.

Manual to application of wind energy

International Nuclear Information System (INIS)

Pinilla, S. A.

1995-01-01

The National Government of Colombia assigned to INEA (Institute of Nuclear Sciences and Alternative Energies), the paper of promotion, diffusion and utilization of sources of energy not - conventional, the one which includes the wind energy. These studies were accomplished mainly in winding zones as the Department La Guajira, area of the Eastern Plains and some sites of mountain chains of the Andes. Internationally, renewable energies utilization is widely used and is included as an important factor in the energetic strategic planning in some countries, where this renewable energy becomes more than 20% to total energy supply. An introduction to the wind energy in some aspects as: the wind resource, global traffic standards of the wind, calculation of the potential of the wind and methods for the calculation of speed measure of the wind are presented. The methodologies for the evaluation of the wind as an energy source, the wind energy technologies, the equipment to wind energy utilization and the implementation of small systems of energy conversion of wind are described

IPP partnerships : forging Canada's wind industry

International Nuclear Information System (INIS)

Magee, J.T.

2006-01-01

Following the request for proposal (RFP)-fueled explosion in renewable energy source development over the past 3 years, independent power producer (IPP) financial expertise has become critical to successful project implementation. This presentation reviewed aspects of Canadian wind market related to independent power producer (IPP) investment activity. A map of major Canadian wind farms operational at the end of 2005 was provided, as well as a map of provinces with utility RFP activity. Planned projects were listed by MW. Recent provincial RFP winners were listed. It was suggested that project execution experience and financial security were highly valued in the recent Hydro-Quebec and Ontario RFP solicitations. Developer consolidation and scaling is likely to continue as large wind IPPs are in the best position to maximize efficiency gains in project economics. Financial strength will continue to be key to winning provincial wind RFPs, and Quebec and Ontario RFPs are likely to be dominated by players with balance sheet security. Smaller developers are losing their competitive position in RFP negotiations as more national and international energy giants move into the wind industry. The consolidation trend is ramping up quickly, and may be closing the window in which international investors can find acquisition targets with experience and viable projects. It was concluded that while small developers with robust projects still exist, they are being acquired at a rapid rate. refs., tabs., figs

Full scale testing for investigation of wind turbine seismic response

Energy Technology Data Exchange (ETDEWEB)

Prowell, I.; Veletzos, M.; Elgamal, A. [California Univ., San Diego, CA (United States). Dept. of Structural Engineering

2008-07-01

In 2007, much of the growth in wind energy development was concentrated in North America and Asia, two regions which periodically experience strong earthquakes that may impact the final turbine design. As such, rational prediction of seismic hazards must be considered in order to maintain and enhance the ability of wind power to compete economically with other energy sources. In response to this challenge, researchers at the University of California, San Diego (UCSD) have experimentally investigated wind turbines to gain an understanding of expected earthquake forces. This paper described the experimental setup for a full scale shake table test of a 65 kW wind turbine. The turbine was excited perpendicular to the axis of the rotor with a seismic base shaking record scaled to various levels. The data was analyzed using simple but effective procedures to provide insight into the observed structural damping of the wind turbine. The experimental investigation showed that full scale seismic testing of wind turbines is possible and can provide valuable insight into dynamic behaviour of wind turbines. The results can be used to develop a more accurate picture of how wind turbines are impacted by earthquakes. The data regarding the low observed super-structure damping provides a basis for calibration and further development of verified design procedures. 20 refs., 3 tabs.

Balancing modern Power System with large scale of wind power

DEFF Research Database (Denmark)

Basit, Abdul; Altin, Müfit; Hansen, Anca Daniela

2014-01-01

Power system operators must ensure robust, secure and reliable power system operation even with a large scale integration of wind power. Electricity generated from the intermittent wind in large propor-tion may impact on the control of power system balance and thus deviations in the power system...... frequency in small or islanded power systems or tie line power flows in interconnected power systems. Therefore, the large scale integration of wind power into the power system strongly concerns the secure and stable grid operation. To ensure the stable power system operation, the evolving power system has...... to be analysed with improved analytical tools and techniques. This paper proposes techniques for the active power balance control in future power systems with the large scale wind power integration, where power balancing model provides the hour-ahead dispatch plan with reduced planning horizon and the real time...

Reliability and cost/worth evaluation of generating systems utilizing wind and solar energy

Science.gov (United States)

Bagen

The utilization of renewable energy resources such as wind and solar energy for electric power supply has received considerable attention in recent years due to adverse environmental impacts and fuel cost escalation associated with conventional generation. At the present time, wind and/or solar energy sources are utilized to generate electric power in many applications. Wind and solar energy will become important sources for power generation in the future because of their environmental, social and economic benefits, together with public support and government incentives. The wind and sunlight are, however, unstable and variable energy sources, and behave far differently than conventional sources. Energy storage systems are, therefore, often required to smooth the fluctuating nature of the energy conversion system especially in small isolated applications. The research work presented in this thesis is focused on the development and application of reliability and economic benefits assessment associated with incorporating wind energy, solar energy and energy storage in power generating systems. A probabilistic approach using sequential Monte Carlo simulation was employed in this research and a number of analyses were conducted with regards to the adequacy and economic assessment of generation systems containing wind energy, solar energy and energy storage. The evaluation models and techniques incorporate risk index distributions and different operating strategies associated with diesel generation in small isolated systems. Deterministic and probabilistic techniques are combined in this thesis using a system well-being approach to provide useful adequacy indices for small isolated systems that include renewable energy and energy storage. The concepts presented and examples illustrated in this thesis will help power system planners and utility managers to assess the reliability and economic benefits of utilizing wind energy conversion systems, solar energy conversion

Program of solar wind data analysis utilizing data from Pioneer 6, Mariner 5 and explorer 35

Science.gov (United States)

Siscoe, G. L.

1972-01-01

A combined data analysis and theoretical program aimed at interpreting and utilizing solar wind data obtained from Pioneer 6, Mariner 5, and Explorer 35 has been completed. A theoretical model of the radial dependence of large scale solar wind inhomogeneities was developed and used to map solar wind variations measured by Explorer 35 to various heliocentric distances and to the orbits of Mercury, Venus, and Mars. The model was also used to determine power spectra velocity, density and temperature variations of 20 R sub s from spectra obtained from the Mariner 5 data at an average heliocentric distance of 180 R sub s. Five stream-stream interaction events in the Pioneer 6 data were analyzed which confirmed the picture of a spiral compression ridge interfacing the two streams and the associated east-west deflections of the solar wind flow. Magnetopause crossings observed in Explorer 35 plasma data were used to develop statics on boundary motions at lunar distance. A study of the geomagnetic disturbance field asymmetry was performed and a model of disturbance field from a partial ring current was developed.

2010 Cost of Wind Energy Review

Energy Technology Data Exchange (ETDEWEB)

Tegen, S. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Hand, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Maples, B. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lantz, E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Schwabe, P. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Smith, A. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2012-04-01

This document provides a detailed description of NREL's levelized cost of wind energy equation, assumptions, and results in 2010, including historical cost trends and future projections for land-based and offshore utility-scale wind.

2010 Cost of Wind Energy Review

Energy Technology Data Exchange (ETDEWEB)

Tegen, S.; Hand, M.; Maples, B.; Lantz, E.; Schwabe, P.; Smith, A.

2012-04-01

This document provides a detailed description of NREL's levelized cost of wind energy equation, assumptions and results in 2010, including historical cost trends and future projections for land-based and offshore utility-scale wind.

The utilization of wind energy

International Nuclear Information System (INIS)

1976-10-01

The statistics of the wind energy in the three aerology stations in the Shahbanu Farah Dam region - over a period of eight years - were evaluated and analyzed. The average of maximal velocity calculations indicates a speed of 15 m/s. The yearly physical conversion value of this energy, is 150,000 kW/h which is quite sufficient for a family of five persons. On a larger scale, this power can be used to supply the energy required for the sediment dredging activities of the Shahbanu Farah Dam. (author)

On Electron-Scale Whistler Turbulence in the Solar Wind

Science.gov (United States)

Narita, Y.; Nakamura, R.; Baumjohann, W.; Glassmeier, K.-H.; Motschmann, U.; Giles, B.; Magnes, W.; Fischer, D.; Torbert, R. B.; Russell, C. T.

2016-01-01

For the first time, the dispersion relation for turbulence magnetic field fluctuations in the solar wind is determined directly on small scales of the order of the electron inertial length, using four-point magnetometer observations from the Magnetospheric Multiscale mission. The data are analyzed using the high-resolution adaptive wave telescope technique. Small-scale solar wind turbulence is primarily composed of highly obliquely propagating waves, with dispersion consistent with that of the whistler mode.

Wind Power Utilization Guide.

Science.gov (United States)

1981-09-01

The expres- sions for the rotor torque for a Darrieus machine can be found in Reference 4.16. The Darrieus wind turbine offers the following... turbine generators, wind -driven turbines , power conditioning, wind power, energy conservation, windmills, economic ana \\sis. 20 ABS 1"ACT (Conti,on... turbines , power conditioning requirements, siting requirements, and the economics of wind power under different conditions. Three examples are given to

Full scale experimental analysis of wind direction changes (EOD)

DEFF Research Database (Denmark)

Hansen, Kurt Schaldemose

2007-01-01

wind direction gust amplitudes associated with the investigated European sites are low compared to the recommended IEC- values. However, these values, as function of the mean wind speed, are difficult to validate thoroughly due to the limited number of fully correlated measurements....... the magnitudes of a joint gust event defined by a simultaneously wind speed- and direction change in order to obtain an indication of the validity of the magnitudes specified in the IEC code. The analysis relates to pre-specified recurrence periods and is based on full-scale wind field measurements. The wind......A coherent wind speed and wind direction change (ECD) load case is defined in the wind turbine standard. This load case is an essential extreme load case that e.g. may be design driving for flap defection of active stall controlled wind turbines. The present analysis identifies statistically...

Large-area photogrammetry based testing of wind turbine blades

Science.gov (United States)

Poozesh, Peyman; Baqersad, Javad; Niezrecki, Christopher; Avitabile, Peter; Harvey, Eric; Yarala, Rahul

2017-03-01

An optically based sensing system that can measure the displacement and strain over essentially the entire area of a utility-scale blade leads to a measurement system that can significantly reduce the time and cost associated with traditional instrumentation. This paper evaluates the performance of conventional three dimensional digital image correlation (3D DIC) and three dimensional point tracking (3DPT) approaches over the surface of wind turbine blades and proposes a multi-camera measurement system using dynamic spatial data stitching. The potential advantages for the proposed approach include: (1) full-field measurement distributed over a very large area, (2) the elimination of time-consuming wiring and expensive sensors, and (3) the need for large-channel data acquisition systems. There are several challenges associated with extending the capability of a standard 3D DIC system to measure entire surface of utility scale blades to extract distributed strain, deflection, and modal parameters. This paper only tries to address some of the difficulties including: (1) assessing the accuracy of the 3D DIC system to measure full-field distributed strain and displacement over the large area, (2) understanding the geometrical constraints associated with a wind turbine testing facility (e.g. lighting, working distance, and speckle pattern size), (3) evaluating the performance of the dynamic stitching method to combine two different fields of view by extracting modal parameters from aligned point clouds, and (4) determining the feasibility of employing an output-only system identification to estimate modal parameters of a utility scale wind turbine blade from optically measured data. Within the current work, the results of an optical measurement (one stereo-vision system) performed on a large area over a 50-m utility-scale blade subjected to quasi-static and cyclic loading are presented. The blade certification and testing is typically performed using International

Small scale wind energy harvesting with maximum power tracking

Directory of Open Access Journals (Sweden)

Joaquim Azevedo

2015-07-01

Full Text Available It is well-known that energy harvesting from wind can be used to power remote monitoring systems. There are several studies that use wind energy in small-scale systems, mainly with wind turbine vertical axis. However, there are very few studies with actual implementations of small wind turbines. This paper compares the performance of horizontal and vertical axis wind turbines for energy harvesting on wireless sensor network applications. The problem with the use of wind energy is that most of the time the wind speed is very low, especially at urban areas. Therefore, this work includes a study on the wind speed distribution in an urban environment and proposes a controller to maximize the energy transfer to the storage systems. The generated power is evaluated by simulation and experimentally for different load and wind conditions. The results demonstrate the increase in efficiency of wind generators that use maximum power transfer tracking, even at low wind speeds.

Studies of Sub-Synchronous Oscillations in Large-Scale Wind Farm Integrated System

Science.gov (United States)

Yue, Liu; Hang, Mend

2018-01-01

With the rapid development and construction of large-scale wind farms and grid-connected operation, the series compensation wind power AC transmission is gradually becoming the main way of power usage and improvement of wind power availability and grid stability, but the integration of wind farm will change the SSO (Sub-Synchronous oscillation) damping characteristics of synchronous generator system. Regarding the above SSO problem caused by integration of large-scale wind farms, this paper focusing on doubly fed induction generator (DFIG) based wind farms, aim to summarize the SSO mechanism in large-scale wind power integrated system with series compensation, which can be classified as three types: sub-synchronous control interaction (SSCI), sub-synchronous torsional interaction (SSTI), sub-synchronous resonance (SSR). Then, SSO modelling and analysis methods are categorized and compared by its applicable areas. Furthermore, this paper summarizes the suppression measures of actual SSO projects based on different control objectives. Finally, the research prospect on this field is explored.

The economic value of accurate wind power forecasting to utilities

Energy Technology Data Exchange (ETDEWEB)

Watson, S J [Rutherford Appleton Lab., Oxfordshire (United Kingdom); Giebel, G; Joensen, A [Risoe National Lab., Dept. of Wind Energy and Atmospheric Physics, Roskilde (Denmark)

1999-03-01

With increasing penetrations of wind power, the need for accurate forecasting is becoming ever more important. Wind power is by its very nature intermittent. For utility schedulers this presents its own problems particularly when the penetration of wind power capacity in a grid reaches a significant level (>20%). However, using accurate forecasts of wind power at wind farm sites, schedulers are able to plan the operation of conventional power capacity to accommodate the fluctuating demands of consumers and wind farm output. The results of a study to assess the value of forecasting at several potential wind farm sites in the UK and in the US state of Iowa using the Reading University/Rutherford Appleton Laboratory National Grid Model (NGM) are presented. The results are assessed for different types of wind power forecasting, namely: persistence, optimised numerical weather prediction or perfect forecasting. In particular, it will shown how the NGM has been used to assess the value of numerical weather prediction forecasts from the Danish Meteorological Institute model, HIRLAM, and the US Nested Grid Model, which have been `site tailored` by the use of the linearized flow model WA{sup s}P and by various Model output Statistics (MOS) and autoregressive techniques. (au)

Stellar feedback in galaxies and the origin of galaxy-scale winds

Science.gov (United States)

Hopkins, Philip F.; Quataert, Eliot; Murray, Norman

2012-04-01

Feedback from massive stars is believed to play a critical role in driving galactic super-winds that enrich the intergalactic medium and shape the galaxy mass function, mass-metallicity relation and other global galaxy properties. In previous papers, we have introduced new numerical methods for implementing stellar feedback on sub-giant molecular cloud (sub-GMC) through galactic scales in numerical simulations of galaxies; the key physical processes include radiation pressure in the ultraviolet through infrared, supernovae (Type I and Type II), stellar winds ('fast' O star through 'slow' asymptotic giant branch winds), and H II photoionization. Here, we show that these feedback mechanisms drive galactic winds with outflow rates as high as ˜10-20 times the galaxy star formation rate. The mass-loading efficiency (wind mass-loss rate divided by the star formation rate) scales roughly as ? (where Vc is the galaxy circular velocity), consistent with simple momentum-conservation expectations. We use our suite of simulations to study the relative contribution of each feedback mechanism to the generation of galactic winds in a range of galaxy models, from Small Magellanic Cloud like dwarfs and Milky Way (MW) analogues to z˜ 2 clumpy discs. In massive, gas-rich systems (local starbursts and high-z galaxies), radiation pressure dominates the wind generation. By contrast, for MW-like spirals and dwarf galaxies the gas densities are much lower and sources of shock-heated gas such as supernovae and stellar winds dominate the production of large-scale outflows. In all of our models, however, the winds have a complex multiphase structure that depends on the interaction between multiple feedback mechanisms operating on different spatial scales and time-scales: any single feedback mechanism fails to reproduce the winds observed. We use our simulations to provide fitting functions to the wind mass loading and velocities as a function of galaxy properties, for use in cosmological

Utilizing a vanadium redox flow battery to avoid wind power deviation penalties in an electricity market

International Nuclear Information System (INIS)

Turker, Burak; Arroyo Klein, Sebastian; Komsiyska, Lidiya; Trujillo, Juan José; Bremen, Lueder von; Kühn, Martin; Busse, Matthias

2013-01-01

Highlights: • Vanadium redox flow battery utilized for wind power grid integration was studied. • Technical and financial analyses at single wind farm level were performed. • 2 MW/6 MW h VRFB is suitable for mitigating power deviations for a 10 MW wind farm. • Economic incentives might be required in the short-term until the VRFB prices drop. - Abstract: Utilizing a vanadium redox flow battery (VRFB) for better market integration of wind power at a single wind farm level was evaluated. A model which combines a VRFB unit and a medium sized (10 MW) wind farm was developed and the battery was utilized to compensate for the deviations resulting from the forecast errors in an electricity market bidding structure. VRFB software model which was introduced in our previous paper was integrated with real wind power data, power forecasts and market data based on the Spanish electricity market. Economy of the system was evaluated by financial assessments which were done by considering the VRFB costs and the amount of deviation penalty payments resulting from forecast inaccuracies

Marketing strategy for retailing small-scale wind energy turbines in Indian markets

OpenAIRE

Harjula, Nina

2009-01-01

The study analyzes the small-scale wind energy markets in Mumbai, focusing on questions: How feasible is the wind energy for SME businesses in Mumbai, and what are the main challenges and opportunities of small-scale wind energy in Mumbai? The study is a qualitative case study, in which, the data has been collected through observing the markets by visiting wind energy sites and companies, interviewing and meeting potential customers and other stakeholders in the market. Theoretical frame...

Videometric research on deformation measurement of large-scale wind turbine blades

Institute of Scientific and Technical Information of China (English)

无

2011-01-01

Utilization of wind energy is a promising way to generate power,and wind turbine blades play a key role in collecting the wind energy effectively.This paper attempts to measure the deformation parameter of wind turbine blades in mechanics experiments using a videometric method. In view that the blades experience small buckling deformation and large integral deformation simultaneously, we proposed a parallel network measurement(PNM) method including the key techniques such as camera network construction,c...

Externalities in utility resource selection: A means to formally recognize the envionmental benefits of wind farms

International Nuclear Information System (INIS)

Birner, S.

1992-01-01

Wind can only make its full contribution to the minimization of the total cost of energy services if it is valued for all the costs that it avoids, including avoided environmental costs. Means of incorporating environmental costs, or externalities, into utility planning decisions are described. Externalities are defined as uncompensated costs or benefits of an action borne by a party other than the one causing the costs. A simple example of the use of externalities in utility resource selection is presented, comparing costs of a coal-fired power plant and a wind farm. Externalities of wind farms are analyzed and found to be very low. An examination of some aspects of legislation in the USA and Canada shows a trend for utility commissions and other regulatory bodies to determine that including externalitites lies within their mandate. By formally recognizing and accounting for the environmental benefits of wind farms, it is seen that externalities can have a significant effect on utility demand for wind energy. A review of USA state actions regarding externalities is appended. 10 refs

Design Performance Standards for Large Scale Wind Farms

DEFF Research Database (Denmark)

Gordon, Mark

2009-01-01

of connection into the Eastern Australian power system under the Rules and guidelines set out by AEMC and NEMMCO (AEMO). Where applicable some international practices are also mentioned. Standards are designed to serve as a technical envelope under which wind farm proponents design the plant and maintain...... ongoing technical compliance of the plant during its operational lifetime. This report is designed to provide general technical information for the wind farm connection engineer to be aware of during the process of connection, registration and operation of wind power plants interconnected into the HV TSO......’s network. No special NER Rule has been used in this document, however V30 (year 2009) has been used as the latest reference on some of the topics discussed. Care has been taken to emphasise certain wind farm design and connection issues that could be considered throughout different stages of the wind farm...

Small-scale wind power design, analysis, and environmental impacts

CERN Document Server

Abraham, John P

2014-01-01

In today's world, clean and robust energy sources are being sought to provide power to residences, commercial operations, and manufacturing enterprises. Among the most appealing energy sources is wind power-with its high reliability and low environmental impact. Wind power's rapid penetration into markets throughout the world has taken many forms, and this book discusses the types of wind power, as well as the appropriate decisions that need to be made regarding wind power design, testing, installation, and analysis. Inside, the authors detail the design of various small-wind systems including horizontal-axis wind turbines (HAWTs) and vertical-axis wind turbines (VAWTs). The design of wind turbines takes advantage of many avenues of investigation, all of which are included in the book. Analytical methods that have been developed over the past few decades are major methods used for design. Alternatively, experimentation (typically using scaled models in wind tunnels) and numerical simulation (using modern comp...

Wind Energy Resource Atlas of Oaxaca

Energy Technology Data Exchange (ETDEWEB)

Elliott, D.; Schwartz, M.; Scott, G.; Haymes, S.; Heimiller, D.; George, R.

2003-08-01

The Oaxaca Wind Resource Atlas, produced by the National Renewable Energy Laboratory's (NREL's) wind resource group, is the result of an extensive mapping study for the Mexican State of Oaxaca. This atlas identifies the wind characteristics and distribution of the wind resource in Oaxaca. The detailed wind resource maps and other information contained in the atlas facilitate the identification of prospective areas for use of wind energy technologies, both for utility-scale power generation and off-grid wind energy applications.

Wind Energy Resource Atlas of Armenia

Energy Technology Data Exchange (ETDEWEB)

Elliott, D.; Schwartz, M.; Scott, G.; Haymes, S.; Heimiller, D.; George, R.

2003-07-01

This wind energy resource atlas identifies the wind characteristics and distribution of the wind resource in the country of Armenia. The detailed wind resource maps and other information contained in the atlas facilitate the identification of prospective areas for use of wind energy technologies for utility-scale power generation and off-grid wind energy applications. The maps portray the wind resource with high-resolution (1-km2) grids of wind power density at 50-m above ground. The wind maps were created at the National Renewable Energy Laboratory (NREL) using a computerized wind mapping system that uses Geographic Information System (GIS) software.

Large-scale kinetic energy spectra from Eulerian analysis of EOLE wind data

Science.gov (United States)

Desbois, M.

1975-01-01

A data set of 56,000 winds determined from the horizontal displacements of EOLE balloons at the 200 mb level in the Southern Hemisphere during the period October 1971-February 1972 is utilized for the computation of planetary- and synoptic-scale kinetic energy space spectra. However, the random distribution of measurements in space and time presents some problems for the spectral analysis. Two different approaches are used, i.e., a harmonic analysis of daily wind values at equi-distant points obtained by space-time interpolation of the data, and a correlation method using the direct measurements. Both methods give similar results for small wavenumbers, but the second is more accurate for higher wavenumbers (k above or equal to 10). The spectra show a maximum at wavenumbers 5 and 6 due to baroclinic instability and then decrease for high wavenumbers up to wavenumber 35 (which is the limit of the analysis), according to the inverse power law k to the negative p, with p close to 3.

Wake Measurements in ECN's Scaled Wind Farm

Energy Technology Data Exchange (ETDEWEB)

Wagenaar, J.W.; Schepers, J.G. [ECN Wind Energy, Petten (Netherlands)

2013-02-15

In ECN's scaled wind farm the wake evolution is studied in two different situations. A single wake is studied at two different locations downstream of a turbine and a single wake is studied in conjunction with a triple wake. Here, the wake is characterized by the wind speed ratio, the turbulence intensity, the vertical wind speed and the turbulence (an)isotropy. Per situation all wake measurements are taken simultaneously together with the inflow conditions.

Lewis Research Center studies of multiple large wind turbine generators on a utility network

Science.gov (United States)

Gilbert, L. J.; Triezenberg, D. M.

1979-01-01

A NASA-Lewis program to study the anticipated performance of a wind turbine generator farm on an electric utility network is surveyed. The paper describes the approach of the Lewis Wind Energy Project Office to developing analysis capabilities in the area of wind turbine generator-utility network computer simulations. Attention is given to areas such as, the Lewis Purdue hybrid simulation, an independent stability study, DOE multiunit plant study, and the WEST simulator. Also covered are the Lewis mod-2 simulation including analog simulation of a two wind turbine system and comparison with Boeing simulation results, and gust response of a two machine model. Finally future work to be done is noted and it is concluded that the study shows little interaction between the generators and between the generators and the bus.

Wind energy basics a guide to home- and community-scale wind energy systems

CERN Document Server

Gipe, Paul

2009-01-01

The availability of clean, renewable power is without question going to be the defining challenge and goal of the 21st century, and wind will lead the way. Internationally acclaimed wind energy expert Paul Gipe is as soberly critical of past energy mistakes as he is convincingly optimistic about the future. The overwhelming challenge of transforming our world from one of fossil carbon to one of clean power seems daunting at best-and paralyzingly impractical at worst. "Wind Energy Basics" offers a solution. Wind power can realistically not only replace the lion's share of oil-, coal-, and natural gasndash; fired electrical plants in the U.S., but also can add enough extra power capacity to allow for most of the cars in the nation to run on electricity. Gipe explains why such a startlingly straightforward solution is eminently doable and can be accomplished much sooner than previously thought-and will have the capacity to resuscitate small and regional economies. "Wind Energy Basics" offers a how-to for home-ba...

Aero-MINE (Motionless INtegrated Energy) for Distributed Scalable Wind Power.

Energy Technology Data Exchange (ETDEWEB)

Houchens, Brent C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Blaylock, Myra L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-06-01

The proposed Aero-MINE technology will extract energy from wind without any exterior moving parts. Aero-MINEs can be integrated into buildings or function stand-alone, and are scalable. This gives them advantages similar to solar panels, but with the added benefit of operation in cloudy or dark conditions. Furthermore, compared to solar panels, Aero-MINEs can be manufactured at lower cost and with less environmental impact. Power generation is isolated internally by the pneumatic transmission of air and the outlet air-jet nozzles amplify the effectiveness. Multiple units can be connected to one centrally located electric generator. Aero-MINEs are ideal for the built-environment, with numerous possible configurations ranging from architectural integration to modular bolt-on products. Traditional wind turbines suffer from many fundamental challenges. The fast-moving blades produce significant aero-acoustic noise, visual disturbances, light-induced flickering and impose wildlife mortality risks. The conversion of massive mechanical torque to electricity is a challenge for gears, generators and power conversion electronics. In addition, the installation, operation and maintenance of wind turbines is required at significant height. Furthermore, wind farms are often in remote locations far from dense regions of electricity customers. These technical and logistical challenges add significantly to the cost of the electricity produced by utility-scale wind farms. In contrast, distributed wind energy eliminates many of the logistical challenges. However, solutions such as micro-turbines produce relatively small amounts of energy due to the reduction in swept area and still suffer from the motion-related disadvantages of utility-scale turbines. Aero-MINEs combine the best features of distributed generation, while eliminating the disadvantages.

Planning your first wind power project. A primer for utilities: Everything you need to know to bring your first wind power plant on-line

International Nuclear Information System (INIS)

Conover, K.; Davis, E.

1994-12-01

This primer has been prepared to help utility personnel become familiar with some or the details relative to wind power technology and project development. It is written as a series of relatively independent chapters to address specific topics or phases of wind power evaluation and development as they might occur within a utility. The topics include: wind prospecting and the first pass analysis, resource validation, project feasibility, resource planning and evaluation, resource acquisition, project development, equipment selection, project design and construction, and plant operation and maintenance

Determination of performance parameters of vertical axis wind turbines in wind tunnel

Directory of Open Access Journals (Sweden)

Nguyen Van Bang

2017-01-01

Full Text Available The paper deals with the determination of the performance parameters of a small vertical axis wind turbines (VAWT, which operate by the utilization of drag forces acting on the blades of the turbine. The performance was evaluated by investigating the electrical power output and torque moment of the wind machine. Measurements were performed on the full-scale model and the experimental data are assessed and compared to other types of wind turbines, with respect to its purpose.

Aeroelastic Stability Investigations for Large-scale Vertical Axis Wind Turbines

International Nuclear Information System (INIS)

2 P O Box 5800, Albuquerque, NM, 87185 (United States))" data-affiliation=" (Senior Member of Technical Staff, Analytical Structural Dynamics Sandia National Laboratories2 P O Box 5800, Albuquerque, NM, 87185 (United States))" >Owens, B C; 2 P O Box 5800, Albuquerque, NM, 87185 (United States))" data-affiliation=" (Principal Member of Technical Staff, Wind Energy Technologies Sandia National Laboratories2 P O Box 5800, Albuquerque, NM, 87185 (United States))" >Griffith, D T

2014-01-01

The availability of offshore wind resources in coastal regions, along with a high concentration of load centers in these areas, makes offshore wind energy an attractive opportunity for clean renewable electricity production. High infrastructure costs such as the offshore support structure and operation and maintenance costs for offshore wind technology, however, are significant obstacles that need to be overcome to make offshore wind a more cost-effective option. A vertical-axis wind turbine (VAWT) rotor configuration offers a potential transformative technology solution that significantly lowers cost of energy for offshore wind due to its inherent advantages for the offshore market. However, several potential challenges exist for VAWTs and this paper addresses one of them with an initial investigation of dynamic aeroelastic stability for large-scale, multi-megawatt VAWTs. The aeroelastic formulation and solution method from the BLade Aeroelastic STability Tool (BLAST) for HAWT blades was employed to extend the analysis capability of a newly developed structural dynamics design tool for VAWTs. This investigation considers the effect of configuration geometry, material system choice, and number of blades on the aeroelastic stability of a VAWT, and provides an initial scoping for potential aeroelastic instabilities in large-scale VAWT designs

Aeroelastic Stability Investigations for Large-scale Vertical Axis Wind Turbines

Science.gov (United States)

Owens, B. C.; Griffith, D. T.

2014-06-01

The availability of offshore wind resources in coastal regions, along with a high concentration of load centers in these areas, makes offshore wind energy an attractive opportunity for clean renewable electricity production. High infrastructure costs such as the offshore support structure and operation and maintenance costs for offshore wind technology, however, are significant obstacles that need to be overcome to make offshore wind a more cost-effective option. A vertical-axis wind turbine (VAWT) rotor configuration offers a potential transformative technology solution that significantly lowers cost of energy for offshore wind due to its inherent advantages for the offshore market. However, several potential challenges exist for VAWTs and this paper addresses one of them with an initial investigation of dynamic aeroelastic stability for large-scale, multi-megawatt VAWTs. The aeroelastic formulation and solution method from the BLade Aeroelastic STability Tool (BLAST) for HAWT blades was employed to extend the analysis capability of a newly developed structural dynamics design tool for VAWTs. This investigation considers the effect of configuration geometry, material system choice, and number of blades on the aeroelastic stability of a VAWT, and provides an initial scoping for potential aeroelastic instabilities in large-scale VAWT designs.

Challenges and options for large scale integration of wind power

International Nuclear Information System (INIS)

Tande, John Olav Giaever

2006-01-01

Challenges and options for large scale integration of wind power are examined. Immediate challenges are related to weak grids. Assessment of system stability requires numerical simulation. Models are being developed - validation is essential. Coordination of wind and hydro generation is a key for allowing more wind power capacity in areas with limited transmission corridors. For the case study grid depending on technology and control the allowed wind farm size is increased from 50 to 200 MW. The real life example from 8 January 2005 demonstrates that existing marked based mechanisms can handle large amounts of wind power. In wind integration studies it is essential to take account of the controllability of modern wind farms, the power system flexibility and the smoothing effect of geographically dispersed wind farms. Modern wind farms contribute to system adequacy - combining wind and hydro constitutes a win-win system (ml)

Transient Thunderstorm Downbursts and Their Effects on Wind Turbines

Directory of Open Access Journals (Sweden)

Hieu H. Nguyen

2014-10-01

Full Text Available The International Electrotechnical Commission (IEC Standard 61400-1 for the design of wind turbines does not explicitly address site-specific conditions associated with anomalous atmospheric events or conditions. Examples of off-standard atmospheric conditions include thunderstorm downbursts, hurricanes, tornadoes, low-level jets, etc. The simulation of thunderstorm downbursts and associated loads on a utility-scale wind turbine is the focus of this study. Since the problem has not received sufficient attention, especially in terms of design, we thus focus in this paper on practical aspects. A wind field model that incorporates component non-turbulent and turbulent parts is described and employed in inflow simulations. The non-turbulent part is based on an available analytical model with some modifications, while the turbulent part is simulated as a stochastic process using standard turbulence power spectral density functions and coherence functions whose defining parameters are related to the downburst characteristics such as the storm translation velocity. Available information on recorded downbursts is used to define two storm scenarios that are studied. Rotor loads are generated using stochastic simulation of the aeroelastic response of a model of a utility-scale 5-MW turbine. An illustrative single storm simulation and the associated turbine response are used to discuss load characteristics and to highlight storm-related and environmental parameters of interest. Extensive simulations for two downbursts are then conducted while varying the storm’s location and track relative to the turbine. Results suggest that wind turbine yaw and pitch control systems clearly influence overall system response. Results also highlight the important effects of both the turbulence as well as the downburst mean wind profiles on turbine extreme loads.

Reliability and Energy Loss in Full-scale Wind Power Converter Considering Grid Codes and Wind Classes

DEFF Research Database (Denmark)

Zhou, Dao; Blaabjerg, Frede; Franke, Toke

2014-01-01

With the increasing penetration of the wind power, reliable operation and cost-effective wind energy production are of more and more importance. As one of the promising configurations, the cost on reliability and production losses of permanent-magnet synchronous generator based full-scale wind......, if the specific designed wind turbine system operates at different wind classes, it can be seen that higher wind class level results in lower lifetime of the power converter. In respect to the cost of the reactive power, either the OE or the UE reactive power increases the energy loss per year significantly...... power converter is studied considering the grid code with reactive power production as well as the annual wind profile. Regarding the reliability, it is found that either the Over-Excited (OE) or the Under-Excited (UE) reactive power injection threatens the lifespan under all wind classes. Meanwhile...

Development of wind energy in Denmark

Energy Technology Data Exchange (ETDEWEB)

Nielsen, P. [Danske Elvaerkers Forenings Udredningsafdeling (DEFU), Lyngby (Denmark)

1994-12-31

In Denmark, wind energy has for centuries been used for many purposes, among these water pumping, milling of grain, and electricity generation. This paper discusses the development of grid-connected wind turbines on a large-scale sponsored by the national government, the Commission of the European Communities and the Danish electric utilities, and small-scale grid-connected wind turbines both privately and utility owned. Siting investigations have shown that it is possible to find sites of reasonable quality for a potential electricity production of at least 10 percent of the expected electricity consumption in 2005 which corresponds to about 1500 MW of installed capacity. Regulations were introduced in 1991 limiting the owners of wind turbines to noise levels from the wind turbines to the existing levels of 45 dB in rural areas, and 40 dB in residential areas and other noise sensitive areas. Studies of the effects of wind turbines on birds found that compared with other human activities, such as farming and car driving, a wind turbine in a bird sanctuary does not have a particular impact on bird life, although there were some effects such as birds moving away from the turbine to breed, forage etc. The Danish Government`s aim to establish 1500 MW of wind power by the year 2005 has some problems. Funding for research, a combination of agreements with the utilities, and production subsidies to private persons and co-operative societies is contributing to the resolution of these problems. 1 tab., 2 figs.

Wind tunnel study of helical and straight-bladed vertical-axis wind turbine wakes

Science.gov (United States)

Bagheri, Maryam; Araya, Daniel

2017-11-01

It is hypothesized that blade curvature can serve as a passive means to control fluid entrainment and wake recovery in vertical-axis wind turbine (VAWT) arrays. We test this experimentally in a wind tunnel using two different VAWT configurations, one with straight blades and another with helical blades, keeping all other experimental parameters fixed. A small-scale, commercially available VAWT (15W max power) is used as the baseline wind tunnel model in each case. The commercial VAWT blades are replaced with either straight or helical blades that are 3D-printed extrusions of the same airfoil cross-section. Results from smoke flow visualization, three-component wake velocity measurements, and turbine power data are presented. These results give insight into the potential use of VAWTs with curved blades in utility-scale wind farms.

Sub-scale Inverse Wind Turbine Blade Design Using Bound Circulation

Science.gov (United States)

Kelley, Christopher; Berg, Jonathan

2014-11-01

A goal of the National Rotor Testbed project at Sandia is to design a sub-scale wind turbine blade that has similitude to a modern, commercial size blade. However, a smaller diameter wind turbine operating at the same tip-speed-ratio exhibits a different range of operating Reynolds numbers across the blade span, thus changing the local lift and drag coefficients. Differences to load distribution also affect the wake dynamics and stability. An inverse wind turbine blade design tool has been implemented which uses a target, dimensionless circulation distribution from a full-scale blade to find the chord and twist along a sub-scale blade. In addition, airfoil polar data are interpolated from a few specified span stations leading to a smooth, manufacturable blade. The iterative process perturbs chord and twist, after running a blade element momentum theory code, to reduce the residual sum of the squares between the modeled sub-scale circulation and the target full-scale circulation. It is shown that the converged sub-scale design also leads to performance similarity in thrust and power coefficients. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy under Contract DE-AC04-94AL85000.

Utilizing the energy from induced wind produce by highway vehicle motion

International Nuclear Information System (INIS)

Abas Abd Wahab; Tong, C.W.

2000-01-01

A research work has been conducted at the Faculty of mechanical Engineering, Universiti Teknologi Malaysia to utilize energy from airflow induced by moving vehicles along the highway for advertising and signboard lighting. Series of data collections have been made at Km 20 Johor Bahru - Kuala Lumpur Plus Highway. Wind anemometer equipped with data recorder has been placed at the highway divider to measure the wind speed induced by the vehicles moving from Johor Bahru to Kuala Lumpur and vice versa. From the data analysis it has been found that the to and from Kuala Lumpur motion of the vehicles induced a stable and continuous source of airflow (wind) ranges from 2 to 4 m/s. The energy in this induced wind has been estimated and has the potential to be used for the above said purpose. Five design models have been tested in the Faculty of mechanical Engineering Low Speed Wind Tunnel and the twisted vertical blades with circular end covers has proven to be the most efficient and suitable. The optimum sizing of the vertical axis wind turbine has also been determined. The details of the collection of wind induced data and analysis, estimation of energy content, the vertical axis wind turbine models testing and results are presented in this paper. (Author)

Impact of Wind Shear and Tower Shadow Effects on Power System with Large Scale Wind Power Penetration

DEFF Research Database (Denmark)

Hu, Weihao; Su, Chi; Chen, Zhe

2011-01-01

presents a simulation model of a variable speed wind farm with permanent magnet synchronous generators (PMSGs) and fullscale back-to-back converters in the simulation tool of DIgSILENT/PowerFactory. In this paper, the impacts of wind shear and tower shadow effects on the small signal stability of power......Grid connected wind turbines are fluctuating power sources due to wind speed variations, the wind shear and the tower shadow effects. The fluctuating power may be able to excite the power system oscillation at a frequency close to the natural oscillation frequency of a power system. This paper...... systems with large scale wind power penetrations are investigated during continuous operation based on the wind turbine model and the power system model....

FY 1998 Report on development of large-scale wind power generation systems. Feasibility study on development of new technologies for wind power generation (Study on the development of wind power generation); 1998 nendo ogata furyoku hatsuden system kaihatsu. Furyoku hatsuden shingijutsu kaihatsu kanosei chosa (furyoku hatsuden gijutsu ni kansuru kaihatsu doko chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey is designed to analyze, e.g., current status of large-scale wind power generation devices/system technologies and development trends worldwide, and to make predictions about future developments, in an effort to contribute to advancements in new technology for wind power generation systems in Japan. The international R and D cooperation programs promoted by IEA and EU have helped the participants produce a number of good results at lower costs. The European countries have developed the wind power generation industries in each area, promoted by the governmental subsidy policies, and are leading the world. The system is becoming larger, from around an average unit capacity of 250kW in the beginning of the 90's to 600kW now, reducing the cost by the scale merit. The improved computer capacity has made it possible to more easily analyze the complicated rotor aerodynamics, structural dynamics, wind characteristics and other factors related to wind power generation systems. The future R and D directions will include world standards for large-scale wind turbines, advancements in wind farm technologies, offshore wind power generation systems, advancement in design technologies, and new concepts for wind power turbine designs, e.g., floating wind turbine. (NEDO)

National Offshore Wind Energy Grid Interconnection Study

Energy Technology Data Exchange (ETDEWEB)

Daniel, John P. [ABB Inc; Liu, Shu [ABB Inc; Ibanez, Eduardo [National Renewable Energy Laboratory; Pennock, Ken [AWS Truepower; Reed, Greg [University of Pittsburgh; Hanes, Spencer [Duke Energy

2014-07-30

The National Offshore Wind Energy Grid Interconnection Study (NOWEGIS) considers the availability and potential impacts of interconnecting large amounts of offshore wind energy into the transmission system of the lower 48 contiguous United States. A total of 54GW of offshore wind was assumed to be the target for the analyses conducted. A variety of issues are considered including: the anticipated staging of offshore wind; the offshore wind resource availability; offshore wind energy power production profiles; offshore wind variability; present and potential technologies for collection and delivery of offshore wind energy to the onshore grid; potential impacts to existing utility systems most likely to receive large amounts of offshore wind; and regulatory influences on offshore wind development. The technologies considered the reliability of various high-voltage ac (HVAC) and high-voltage dc (HVDC) technology options and configurations. The utility system impacts of GW-scale integration of offshore wind are considered from an operational steady-state perspective and from a regional and national production cost perspective.

Mexico Wind Resource Assessment Project

Energy Technology Data Exchange (ETDEWEB)

Schwartz, M.N.; Elliott, D.L.

1995-05-01

A preliminary wind energy resource assessment of Mexico that produced wind resource maps for both utility-scale and rural applications was undertaken as part of the Mexico-U.S. Renewable Energy Cooperation Program. This activity has provided valuable information needed to facilitate the commercialization of small wind turbines and windfarms in Mexico and to lay the groundwork for subsequent wind resource activities. A surface meteorological data set of hourly data in digital form was utilized to prepare a more detailed and accurate wind resource assessment of Mexico than otherwise would have been possible. Software was developed to perform the first ever detailed analysis of the wind characteristics data for over 150 stations in Mexico. The hourly data set was augmented with information from weather balloons (upper-air data), ship wind data from coastal areas, and summarized wind data from sources in Mexico. The various data were carefully evaluated for their usefulness in preparing the wind resource assessment. The preliminary assessment has identified many areas of good-to-excellent wind resource potential and shows that the wind resource in Mexico is considerably greater than shown in previous surveys.

The U.S. wind market is back

International Nuclear Information System (INIS)

Azua, C.R. de

2000-01-01

The recent growth in wind energy projects in the US was spurred by supportive policies in a few states, steadily improving economics, the federal wind energy Production Tax Credit and emerging green power programs. Wind farms are springing up around the US, providing clean energy as well as an economic boon to farmers and local communities. This year's headlines announced the rebirth of the US wind energy market, as wind farms were dedicated in local communities from coast to coast. At this year's exuberant pace of development, utility-scale wind energy seems well on its way to generating 5% of the nation's electricity by 2020, the target set by the Administration and announced by Energy Secretary Bill Richardson at the wind industry's annual conference earlier this year. Wind energy projects have mushroomed throughout the country, most notably in the Midwest. In the eighteen months from July 1998 to December 1999, the American Wind Energy Association (AWEA) estimates that wind energy companies will have added almost 900 megawatts (MW) to the nation's generating capacity. At the same time, new, more efficient turbines replaced some 200 MW of aging equipment. In all, 1,096 MW of new wind generators were installed over that period, representing an investment of well over $1.1 billion and bringing American utility-scale generating capacity to over 2,500 MW

Size Reduction Techniques for Large Scale Permanent Magnet Generators in Wind Turbines

Science.gov (United States)

Khazdozian, Helena; Hadimani, Ravi; Jiles, David

2015-03-01

Increased wind penetration is necessary to reduce U.S. dependence on fossil fuels, combat climate change and increase national energy security. The U.S Department of Energy has recommended large scale and offshore wind turbines to achieve 20% wind electricity generation by 2030. Currently, geared doubly-fed induction generators (DFIGs) are typically employed in the drivetrain for conversion of mechanical to electrical energy. Yet, gearboxes account for the greatest downtime of wind turbines, decreasing reliability and contributing to loss of profit. Direct drive permanent magnet generators (PMGs) offer a reliable alternative to DFIGs by eliminating the gearbox. However, PMGs scale up in size and weight much more rapidly than DFIGs as rated power is increased, presenting significant challenges for large scale wind turbine application. Thus, size reduction techniques are needed for viability of PMGs in large scale wind turbines. Two size reduction techniques are presented. It is demonstrated that 25% size reduction of a 10MW PMG is possible with a high remanence theoretical permanent magnet. Additionally, the use of a Halbach cylinder in an outer rotor PMG is investigated to focus magnetic flux over the rotor surface in order to increase torque. This work was supported by the National Science Foundation under Grant No. 1069283 and a Barbara and James Palmer Endowment at Iowa State University.

Optimal Selection of AC Cables for Large Scale Offshore Wind Farms

DEFF Research Database (Denmark)

Hou, Peng; Hu, Weihao; Chen, Zhe

2014-01-01

The investment of large scale offshore wind farms is high in which the electrical system has a significant contribution to the total cost. As one of the key components, the cost of the connection cables affects the initial investment a lot. The development of cable manufacturing provides a vast...... and systematical way for the optimal selection of cables in large scale offshore wind farms....

Change-actors in the U.S. electric energy system: The role of environmental groups in utility adoption and diffusion of wind power

International Nuclear Information System (INIS)

Doblinger, Claudia; Soppe, Birthe

2013-01-01

We study the contribution of environmental groups to new technology adoption and diffusion by dominant incumbents. Building on institutional and social movement theory, we develop a theoretical framework that sheds light on environmental groups as change-actors. We theorize that by approaching embedded key constituents with various strategic actions, environmental groups affect taken-for-granted beliefs, build legitimacy for renewable energy technologies, and convince skeptical constituents to support the new technology. We verify our theoretical framework with a case study of wind power development in Colorado. We find that environmentalists educate constituents on the benefits of the new technology, engage in activities leading to regulatory and legislative decisions for wind, while also providing direct assistance to the utility. As a result, utilities are both pressured and encouraged to adopt and diffuse wind power on a large-scale. This research directs attention to the role of environmental groups as change-actors and the legitimating effects of their actions. It highlights their part in creating a more favorable institutional environment for new technologies while directly influencing the incumbent's technology choice. This paper contributes to an understanding of bottom-up, actor-initiated changes in energy systems taking into account both the systemic technological infrastructure and the institutional context. - Highlights: • We study environmentalists′ impact on utility-scale renewable technology diffusion. • Incumbent-dominated systems hinder the diffusion of new technologies. • Environmental groups′ strategic actions increase legitimacy for new technologies. • Environmental groups′ legitimating actions affect incumbent′s technology choice. • Environmental groups create a favorable institutional context for new technologies

Ancillary Frequency Control of Direct Drive Full-Scale Converter Based Wind Power Plants

DEFF Research Database (Denmark)

Hu, Weihao; Su, Chi; Fang, Jiakun

2013-01-01

This paper presents a simulation model of a wind power plant based on a MW-level variable speed wind turbine with a full-scale back-to-back power converter developed in the simulation tool of DIgSILENT Power Factory. Three different kinds of ancillary frequency control strategies, namely inertia...... control strategies are effective means for providing ancillary frequency control of variable speed wind turbines with full-scale back-to-back power converters....... emulation, primary frequency control and secondary frequency control, are proposed in order to improve the frequency stability of power systems. The modified IEEE 39-bus test system with a large-scale wind power penetration is chosen as the studied power system. Simulation results show that the proposed...

Wind energy in Europe

International Nuclear Information System (INIS)

Evans, L.C.

1992-01-01

Wind energy should be an important part of the energy supply mix, both at home and abroad, to provide cleaner air and a more stable fuel supply. Not only can wind energy contribute to solving complex global issues, it also can provide a large market for American technological leadership. Even though utilities are paying more attention to wind in a number of states, there are no plans for major installations of wind power plants in the United States. At the same time, European nations have developed aggressive wind energy development programs, including both ambitious research and development efforts and market incentives. Many countries recognize the importance of the clean energy provided by wind technology and are taking steps to promote their fledgling domestic industries. The emphasis on market incentives is starting to pay off. In 1991, European utilities and developers installed nearly twice as much wind capacity as Americans did. In 1992 the gap will be even greater. This article reviews aggressive incentives offered by European governments to boost their domestic wind industries at home and abroad in this almost $1 billion per year market. By offering substantial incentives - considerably more than the American Wind Energy Association (AWEA) is proposing - European nations are ensuring dramatic near-term wind energy development and are taking a major step toward dominating the international wind industry of the 21st century

Improving Wind Farm Dispatchability Using Model Predictive Control for Optimal Operation of Grid-Scale Energy Storage

Directory of Open Access Journals (Sweden)

Douglas Halamay

2014-09-01

Full Text Available This paper demonstrates the use of model-based predictive control for energy storage systems to improve the dispatchability of wind power plants. Large-scale wind penetration increases the variability of power flow on the grid, thus increasing reserve requirements. Large energy storage systems collocated with wind farms can improve dispatchability of the wind plant by storing energy during generation over-the-schedule and sourcing energy during generation under-the-schedule, essentially providing on-site reserves. Model predictive control (MPC provides a natural framework for this application. By utilizing an accurate energy storage system model, control actions can be planned in the context of system power and state-of-charge limitations. MPC also enables the inclusion of predicted wind farm performance over a near-term horizon that allows control actions to be planned in anticipation of fast changes, such as wind ramps. This paper demonstrates that model-based predictive control can improve system performance compared with a standard non-predictive, non-model-based control approach. It is also demonstrated that secondary objectives, such as reducing the rate of change of the wind plant output (i.e., ramps, can be considered and successfully implemented within the MPC framework. Specifically, it is shown that scheduling error can be reduced by 81%, reserve requirements can be improved by up to 37%, and the number of ramp events can be reduced by 74%.

Wind Resource Atlas of Oaxaca (CD-ROM)

Energy Technology Data Exchange (ETDEWEB)

Elliott, D.; Schwartz, M.; Scott, G.; Haymes, S.; Heimiller, D.; George, R.

2003-08-01

The CD version of the Oaxaca Wind Resource Atlas, produced by the National Renewable Energy Laboratory's (NREL's) wind resource group, is the result of an extensive mapping study for the Mexican State of Oaxaca. This atlas identifies the wind characteristics and distribution of the wind resource in Oaxaca. The detailed wind resource maps and other information contained in the atlas facilitate the identification of prospective areas for use of wind energy technologies, both for utility-scale power generation and off-grid wind energy applications.

Evaluation small scale, grid connected wind and solar distributed generation systems in Jordan

International Nuclear Information System (INIS)

Naji, G. J.; Tahboub, K. K.; Jalham, I. S.

2011-01-01

In this paper, the potential of utilizing wind and solar Private Distributed Generation (PDG) for utility interactive systems is investigated for 11 selected stations (sites) in Jordan. Six customer categories are considered: residential, office, commercial mall, school, hospital and hotel. The main goal of this study was to evaluate the potential of utilizing different grid connected PDG under different conditions such as their location, size, served building category, number of people who share and own the equipment and system type whether wind, solar or hybrid based. It was found that solar systems are still not attractive for all location due to their associated high cost, while wind systems would vary widely depending on the customer category, location and the size of the equipment. Based on the Benefit to Cost ratio criterion, the most attractive sites for installing wind PDGS for residential communities are Ras Muneef, Mafraq, Aqaba, Irbid and H5, while it doesn't seem attractive at Amman,Shoubak, Ghor Essafi, Deir Alla, Maan and H4. On the other hand, the wind on-grid PDGS is very attractive at Ras Muneef, mafraq and Aqaba for commercial buildings, less attractive at H5 and irbid, while it's not attractive at the other sites. The attraction for hybrid PDG systems is closer to those of wind systems alone. (authors).

Evaluation of offshore wind resources by scale of development

DEFF Research Database (Denmark)

Möller, Bernd; Hong, Lixuan; Lonsing, Reinhard

-economic model operating in a geographical information systems (GIS) environment, which describes resources, costs and area constraints in a spatially explicit way, the relation between project size, location, costs and ownership is analysed. Two scenarios are presented, which describe a state......Offshore wind energy has developed rapidly in terms of turbine and project size, and currently undergoes a significant up-scaling to turbines and parks at greater distance to shore and deeper waters. Expectations to the positive effect of economies of scale on power production costs, however, have...... can be explained by deeper water, higher distance to shore, bottlenecks in supply or higher raw material costs. The present paper addresses the scale of offshore wind parks for Denmark and invites to reconsider the technological and institutional choices made. Based on a continuous resource...

Evaluation of offshore wind resources by scale of development

DEFF Research Database (Denmark)

Möller, Bernd; Hong, Lixuan; Lonsing, Reinhard

2012-01-01

-economic model operating in a geographical information systems (GIS) environment, which describes resources, costs and area constraints in a spatially explicit way, the relation between project size, location, costs and ownership is analysed. Two scenarios are presented, which describe a state......Offshore wind energy has developed rapidly in terms of turbine and project size, and currently undergoes a significant up-scaling to turbines and parks at greater distance to shore and deeper waters. Expectations to the positive effect of economies of scale on power production costs, however, have...... can be explained by deeper water, higher distance to shore, bottlenecks in supply or higher raw material costs. The present paper addresses the scale of offshore wind parks for Denmark and invites to reconsider the technological and institutional choices made. Based on a continuous resource...

Electric power from offshore wind via synoptic-scale interconnection.

Science.gov (United States)

Kempton, Willett; Pimenta, Felipe M; Veron, Dana E; Colle, Brian A

2010-04-20

World wind power resources are abundant, but their utilization could be limited because wind fluctuates rather than providing steady power. We hypothesize that wind power output could be stabilized if wind generators were located in a meteorologically designed configuration and electrically connected. Based on 5 yr of wind data from 11 meteorological stations, distributed over a 2,500 km extent along the U.S. East Coast, power output for each hour at each site is calculated. Each individual wind power generation site exhibits the expected power ups and downs. But when we simulate a power line connecting them, called here the Atlantic Transmission Grid, the output from the entire set of generators rarely reaches either low or full power, and power changes slowly. Notably, during the 5-yr study period, the amount of power shifted up and down but never stopped. This finding is explained by examining in detail the high and low output periods, using reanalysis data to show the weather phenomena responsible for steady production and for the occasional periods of low power. We conclude with suggested institutions appropriate to create and manage the power system analyzed here.

Electric power from offshore wind via synoptic-scale interconnection

Science.gov (United States)

Kempton, Willett; Pimenta, Felipe M.; Veron, Dana E.; Colle, Brian A.

2010-01-01

World wind power resources are abundant, but their utilization could be limited because wind fluctuates rather than providing steady power. We hypothesize that wind power output could be stabilized if wind generators were located in a meteorologically designed configuration and electrically connected. Based on 5 yr of wind data from 11 meteorological stations, distributed over a 2,500 km extent along the U.S. East Coast, power output for each hour at each site is calculated. Each individual wind power generation site exhibits the expected power ups and downs. But when we simulate a power line connecting them, called here the Atlantic Transmission Grid, the output from the entire set of generators rarely reaches either low or full power, and power changes slowly. Notably, during the 5-yr study period, the amount of power shifted up and down but never stopped. This finding is explained by examining in detail the high and low output periods, using reanalysis data to show the weather phenomena responsible for steady production and for the occasional periods of low power. We conclude with suggested institutions appropriate to create and manage the power system analyzed here. PMID:20368464

The development of the Dutch wind energy technology in an international perspective

International Nuclear Information System (INIS)

Beurskens, H.J.M.

1990-01-01

An overview is given of the developments in the Dutch wind energy industry and the position of that industry in the industrialized world. First attention is paid to some historical developments of the modern wind energy technology in the Netherlands compared to some other countries. The start of the Integral Wind energy Program (IPW) at the end of 1985 brought the Dutch know-how of wind energy back on the international level. Next a brief overview is given of governmental wind energy programs which resulted in various projects aimed at designing, testing and implementing wind turbines in the Netherlands. Here too a comparison is made with other countries concerning the realized capacity, investments, and attempts to commercialize the wind turbines. The technological developments in the Netherlands can be characterized as gradual: step-by-step larger wind turbines (i.e. larger capacities) will be developed. The development of multi-megawatt turbines is too risky and too costly at present. Some final remarks state that the present position of the Dutch wind energy industry and the Dutch research activities are good starting-points to realize an important part of the wind energy capacity in Europe, or even the world. Recommendations are given by which the Dutch wind energy industry can operate with success on the international market. 5 figs., 3 tabs., 2 refs

Wind energy in Bavaria; Windenergie in Bayern

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-09-15

For centuries we use the wind for our purposes. Previously, the wind was almost exclusively important for the economy, and propels windmills and merchant ships. During the 20th century, wind was used especially in leisure such as sailing, surfing and flying. Now we remind ourselves to use the wind energy to our livelihoods - in the power generation by means of wind turbines. Thanks to the financial support from the Renewable Energy Law, wind energy is utilized more and more for ten years. Meanwhile, Germany is internationally ranked third in terms of installed capacity in wind energy.

Simultaneous nested modeling from the synoptic scale to the LES scale for wind energy applications

DEFF Research Database (Denmark)

Liu, Yubao; Warner, Tom; Liu, Yuewei

2011-01-01

This paper describes an advanced multi-scale weather modeling system, WRF–RTFDDA–LES, designed to simulate synoptic scale (~2000 km) to small- and micro-scale (~100 m) circulations of real weather in wind farms on simultaneous nested grids. This modeling system is built upon the National Center f...

Wind Power: How Much, How Soon, and At What Cost?

Energy Technology Data Exchange (ETDEWEB)

Wiser, Ryan H; Hand, Maureen

2010-01-01

The global wind power market has been growing at a phenomenal pace, driven by favorable policies towards renewable energy and the improving economics of wind projects. On a going forward basis, utility-scale wind power offers the potential for significant reductions in the carbon footprint of the electricity sector. Specifically, the global wind resource is vast and, though accessing this potential is not costless or lacking in barriers, wind power can be developed at scale in the near to medium term at what promises to be an acceptable cost.

Small Wind Turbine Installation Compatibility Demonstration Methodology

Science.gov (United States)

2013-08-01

wind turbine (HAWT) and one 2.9-kW vertical-axis wind turbine (VAWT), we planned to measure radar, acoustic and seismic, turbulence, bird and...non-issue for small turbines . The majority of studies of bat and bird interactions with wind turbines are for large turbines (BPA 2002; Whittam...et al. 2010). The majority of studies of bat and bird interactions with wind energy facil- ities are for utility-scale turbines (> 1 MW) with

Pilot project wind power - Large scale wind power in northern Sweden; Pilotprojekt vindkraft - Storskalig vindkraft i norra Sverige

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-07-01

The Swedish Energy Agency granted 2009-04-20 Svevind AB financial aid to implement {sup P}ilot project wind power- Large scale wind power in northern Sweden{sup .} The purpose of the aid is to implement pilot sub-projects in wind power, to to increase knowledge for the larger establishments. The Energy Agency said in its decision that the projects Dragaliden and Gabriel Mountain is of 'great importance for future large-scale development of wind power in Sweden'. The special conditions prevailing in the project, forest environment and cold climate, gives the possibility of studies of wind turbines on birds, reindeer herding and hunting and the more technical aspects, such as de-icing and obstacle lighting. The objectives of the project, in addition to the construction and operation of 32 wind turbines, has been to include evaluating the permit process, studying the social effects around the wind power, to study the impact on small game hunting, perform tests of the de-icing system, investigate impacts on reindeer herding and explain the outcome of the project-generated rural funds. Some of the above sub-projects have been completed, which are reported in this report. For the sub-projects still in progress, the report presents the results to date, until the completion.

A real-scale helical coil winding trial of the Large Helical Device

International Nuclear Information System (INIS)

Senba, T.; Yamamoto, T.; Tamaki, T.; Asano, K.; Suzuki, S.; Yamauchi, T.; Uchida, K.; Nakanishi, K.; Yamagiwa, T.; Suzuki, S.; Miyoshi, R.; Sasa, H.; Watanabe, S.; Tatemura, M.; Hatada, N.; Yamaguchi, S.; Imagawa, S.; Yanagi, N.; Satow, T.; Yamamoto, J.; Motojima, O.

1995-01-01

A real-scale helical coil winding trial of the Large Helical Device (LHD) has been conducted for a study of coil winding configuration and winding methods and for exhibiting the state of the art. It includes construction and test run of a specifically designed winding machine and development of various manufacturing methods for accurate coil winding. It has been carried out in Hitachi Works before in situ winding, and has provided much needed engineering data for construction of the LHD. (orig.)

Matching of wind turbine type and system scale to wind conditions; Chiten no fukyo ni taisuru furyoku turbine no keitai to sytem taikaku no seigosei ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Wakui, T. [Japan Society for the Promotion of Science, Tokyo (Japan); Tanzawa, Y. [Nippon Institute of Technology, Saitama (Japan); Ota, E. [Waseda University, Tokyo (Japan). School of Science and Engineering; Hashizume, T.

2000-09-25

The matching of the wind turbine type and system scale of the stand-alone wind turbine generator system to wind conditions is investigated using our dynamic simulation model. This paper examines three types of wind turbines: the Darrieus-Savonius hybrid wind turbine, the Darrieus turbine proper and the up-wind Propeller turbine. These systems are mainly operated at a constant tip speed ratio, which refers to a maximum power coefficient. As a computed result of the net extracting energy under fluctuations of wind speed and direction, the Darrieus turbine proper has little conformability to wind fluctuations because of its output characteristics. As for other wind turbines, large-scale systems do not always have advantages over small-scale systems as the effect of the dynamic characteristics. Furthermore, it is confirmed that the net extracting power of the Propeller turbine under wind direction fluctuations is much reduced when compared with that of the hybrid wind turbine. Thus, it is concluded that the appropriate wind turbine type and system scale exist for each wind condition. (author)

Design of an aeroelastically tailored 10 MW wind turbine rotor

DEFF Research Database (Denmark)

Zahle, Frederik; Tibaldi, Carlo; Pavese, Christian

2016-01-01

This work presents an integrated multidisciplinary wind turbine optimization framework utilizing state-of-the-art aeroelastic and structural tools, capable of simultaneous design of the outer geometry and internal structure of the blade. The framework is utilized to design a 10 MW rotor constrained...... not to exceed the design loads of an existing reference wind turbine. The results show that through combined geometric tailoring of the internal structure and aerodynamic shape of the blade it is possible to achieve significant passive load alleviation that allows for a 9% longer blade with an increase in AEP...

Aerodynamics of small-scale vertical-axis wind turbines

Science.gov (United States)

Paraschivoiu, I.; Desy, P.

1985-12-01

The purpose of this work is to study the influence of various rotor parameters on the aerodynamic performance of a small-scale Darrieus wind turbine. To do this, a straight-bladed Darrieus rotor is calculated by using the double-multiple-streamtube model including the streamtube expansion effects through the rotor (CARDAAX computer code) and the dynamicstall effects. The straight-bladed Darrieus turbine is as expected more efficient with respect the curved-bladed rotor but for a given solidity is operates at higher wind speeds.

The viability of balancing wind generation with large scale energy storage

International Nuclear Information System (INIS)

Nyamdash, Batsaikhan; Denny, Eleanor; O'Malley, Mark

2010-01-01

This paper studies the impact of combining wind generation and dedicated large scale energy storage on the conventional thermal plant mix and the CO 2 emissions of a power system. Different strategies are proposed here in order to explore the best operational strategy for the wind and storage system in terms of its effect on the net load. Furthermore, the economic viability of combining wind and large scale storage is studied. The empirical application, using data for the Irish power system, shows that combined wind and storage reduces the participation of mid-merit plants and increases the participation of base-load plants. Moreover, storage negates some of the CO 2 emissions reduction of the wind generation. It was also found that the wind and storage output can significantly reduce the variability of the net load under certain operational strategies and the optimal strategy depends on the installed wind capacity. However, in the absence of any supporting mechanism none of the storage devices were economically viable when they were combined with the wind generation on the Irish power system. - Research Highlights: → Energy storage would displace the peaking and mid-merit plants generations by the base-load plants generations. Energy storage may negate the CO 2 emissions reduction that is due to the increased wind generations. →Energy storage reduces the variation of the net load. →Under certain market conditions, merchant type energy storage is not viable.

Wind energy potential in Chile: Assessment of a small scale wind farm for residential clients

International Nuclear Information System (INIS)

Becerra, Miguel; Morán, José; Jerez, Alejandro; Cepeda, Francisco; Valenzuela, Miguel

2017-01-01

Highlights: • An assessment of a small scale wind farm was carried out. • Two Chilean locations were selected, which are geographically dissimilar. • The software tool selected for the project’s evaluation was HOMER. • All the project’s financial evaluations were negative. • Government policy tools and their applications were discussed. - Abstract: This work presents a techno-financial evaluation of two Chilean locations with promising wind potential: Laguna Verde placed in the central region of the country, and Porvenir in the southern region. A small scale wind farm was studied, considering a nominal electrical production capacity of 90 kW. This facility is comprised of three wind turbine models, all available in the national market. Currently, the tariff method used in Chile is the net billing scheme, where the energy bought and sold to the grid has different prices. The study is based on 300 hypothetical residential households. The software tool used to perform the assessment was the Hybrid Optimization of Multiple Energy Resources (HOMER). For all the scenarios the results showed a Net Present Cost (NPC), instead of a financial profit from the proposed projects. A sensitivity analysis was also carried out. From the group of variables studied, the NPC exhibited itself as more sensitive to the price of buying energy from the grid and to the annual average wind speed. Finally, a few government policies and their applications are discussed.

Wind and Photovoltaic Large-Scale Regional Models for hourly production evaluation

DEFF Research Database (Denmark)

Marinelli, Mattia; Maule, Petr; Hahmann, Andrea N.

2015-01-01

This work presents two large-scale regional models used for the evaluation of normalized power output from wind turbines and photovoltaic power plants on a European regional scale. The models give an estimate of renewable production on a regional scale with 1 h resolution, starting from a mesosca...... of the transmission system, especially regarding the cross-border power flows. The tuning of these regional models is done using historical meteorological data acquired on a per-country basis and using publicly available data of installed capacity.......This work presents two large-scale regional models used for the evaluation of normalized power output from wind turbines and photovoltaic power plants on a European regional scale. The models give an estimate of renewable production on a regional scale with 1 h resolution, starting from a mesoscale...

Wind tunnel testing of scaled models of a newly developed Darrieus-style vertical axis wind turbine with auxiliary straight blades

International Nuclear Information System (INIS)

Scungio, M.; Arpino, F.; Focanti, V.; Profili, M.; Rotondi, M.

2016-01-01

Highlights: • Wind tunnel investigations of Darrieus-style VAWT with auxiliary blades have been made. • Results have been compared with those from standard Darrieus VAWT. • Static and dynamic power and torque coefficients were measured and evaluated. • The auxiliary airfoils have demonstrated to give more torque at the lower wind speeds. • The proposed VAWT configuration is able to work in a wide range of wind speeds. - Abstract: Renewable sources of energy, needed because of the increasing price of fossil derivatives, global warming and energy market instabilities, have led to an increasing interest in wind energy. Among the different typologies, small scale Vertical Axis Wind Turbines (VAWT) present the greatest potential for off grid power generation at low wind speeds. In the present work, wind tunnel investigations about the performance of an innovative configuration of straight-blades Darrieus-style vertical axis micro wind turbine, specifically developed for small scale energy conversion at low wind speeds, has been made on scaled models. The micro turbine under investigation consists of three pairs of airfoils. Each pair consists of a main and auxiliary airfoil with different chord lengths. A standard Darrieus configuration, consisting of three single airfoils, was also tested for comparison. The experiments were conducted in a closed circuit open chamber wind tunnel facility available at the Laboratory of Industrial Measurements (LaMI) of the University of Cassino and Lazio Meridionale (UNICLAM). Measured data were reported in terms of dimensionless power and torque coefficients for dynamic performance analysis and static torque coefficient for static performance analysis. The adoption of auxiliary airfoils has demonstrated to give more dynamic torque at the lower wind speeds with respect to a standard Darrieus rotor, resulting in better performance for all the wind speeds considered. In terms of dynamic power coefficient, the standard Darrieus

STUDY OF INFLUENCE OF WIND-POWER STATIONS ON BIRDS: ANALYSIS OF INTERNATIONAL PRACTICES

Directory of Open Access Journals (Sweden)

Gorlov P. I.

2012-06-01

Full Text Available The world experience of bird collisions with wind-power stations was analyzed. The detailcharacteristics of principal threats to the birds during building and exploitation of wind-power stations was done. Comparative analysis of factors caused annual birds mortality was performed. Some proposals of negative influence minimization were suggested for wind-power stations utilization.

Lower Sioux Wind Feasibility & Development

Energy Technology Data Exchange (ETDEWEB)

Minkel, Darin

2012-04-01

This report describes the process and findings of a Wind Energy Feasibility Study (Study) conducted by the Lower Sioux Indian Community (Community). The Community is evaluating the development of a wind energy project located on tribal land. The project scope was to analyze the critical issues in determining advantages and disadvantages of wind development within the Community. This analysis addresses both of the Community's wind energy development objectives: the single turbine project and the Commerical-scale multiple turbine project. The main tasks of the feasibility study are: land use and contraint analysis; wind resource evaluation; utility interconnection analysis; and project structure and economics.

Social assessment of wind power. Part 4: International position and development conditions of the Danish wind turbine industry

International Nuclear Information System (INIS)

Karnoee, P.; Joergensen, U.

1995-12-01

Today, the Danish wind turbine industry is positioned as a global market leader on a fast growing international market. The conclusion and observation of this report are: 1. The international market for wind power is likely to grow fast over the next 5 years (a self-reinforcing development) and the Danish wind turbine industry has the potential to increase export from the present DKK 2 billion per year to DKK 4 billion per year. 2. The leading market position is achieved after the collapse of the California market in 1987. The last four years have been export-driven growth together with the development of complementary assets to support a strong product technology. 3. The Danish position might be threatened by the new competitors, but it is our view that it takes 2-3 years before they have equivalent competences, and since the Danish companies are presently also mobilizing resources and competences it is not likely that they are easily outperformed. 4. A continued installation of wind power in Denmark is important to support the sustaining of the international position in the coming years. Through, it is not the volume size of the domestic market, but rather a stable market which serves as a home base for the industry. Not only for the reference and testing of new wind turbines, but also the knowledge networks between manufacturers and suppliers and between manufacturers and the Test Station for Windmills at Risoe. (EG) 51 refs

ANEMOS: Development of a next generation wind power forecasting system for the large-scale integration of onshore and offshore wind farms.

Science.gov (United States)

Kariniotakis, G.; Anemos Team

2003-04-01

offshore wind farms taking into account advances in marine meteorology (interaction between wind and waves, coastal effects). The benefits from the use of satellite radar images for modeling local weather patterns are investigated. A next generation forecasting software, ANEMOS, will be developed to integrate the various models. The tool is enhanced by advanced Information Communication Technology (ICT) functionality and can operate both in stand alone, or remote mode, or be interfaced with standard Energy or Distribution Management Systems (EMS/DMS) systems. Contribution: The project provides an advanced technology for wind resource forecasting applicable in a large scale: at a single wind farm, regional or national level and for both interconnected and island systems. A major milestone is the on-line operation of the developed software by the participating utilities for onshore and offshore wind farms and the demonstration of the economic benefits. The outcome of the ANEMOS project will help consistently the increase of wind integration in two levels; in an operational level due to better management of wind farms, but also, it will contribute to increasing the installed capacity of wind farms. This is because accurate prediction of the resource reduces the risk of wind farm developers, who are then more willing to undertake new wind farm installations especially in a liberalized electricity market environment.

Large-scale offshore wind energy. Cost analysis and integration in the Dutch electricity market

International Nuclear Information System (INIS)

De Noord, M.

1999-02-01

The results of analysis of the construction and integration costs of large-scale offshore wind energy (OWE) farms in 2010 are presented. The integration of these farms (1 and 5 GW) in the Dutch electricity distribution system have been regarded against the background of a liberalised electricity market. A first step is taken for the determination of costs involved in solving integration problems. Three different types of foundations are examined: the mono-pile, the jacket and a new type of foundation: the concrete caisson pile: all single-turbine-single-support structures. For real offshore applications (>10 km offshore, at sea-depths >20 m), the concrete caisson pile is regarded as the most suitable. The price/power ratios of wind turbines are analysed. It is assumed that in 2010 turbines in the power range of 3-5 MW are available. The main calculations have been conducted for a 3 MW turbine. The main choice in electrical infrastructure is for AC or DC. Calculations show that at distances of 30 km offshore and more, the use of HVDC will result in higher initial costs but lower operating costs. The share of operating and maintenance (O ampersand M) costs in the kWh cost price is approximately 3.3%. To be able to compare the two farms, a base case is derived with a construction time of 10 years for both. The energy yield is calculated for a wind regime offshore of 9.0 m/s annual mean wind speed. Per 3 MW turbine this results in an annual energy production of approximately 12 GWh. The total farm efficiency amounts to 82%, resulting in a total farm capacity factor of 38%. With a required internal rate of return of 15%, the kWh cost price amounts to 0.24 DFl and 0.21 DFl for the 1 GW and 5 GW farms respectively in the base case. The required internal rate of return has a large effect on the kWh cost price, followed by costs of subsystems. O ampersand M costs have little effect on the cost price. Parameter studies show that a small cost reduction of 5% is possible when

Flying with the wind: Scale dependency of speed and direction measurements in modelling wind support in avian flight

Science.gov (United States)

Safi, Kamran; Kranstauber, Bart; Weinzierl, Rolf P.; Griffin, Larry; Reese, Eileen C.; Cabot, David; Cruz, Sebastian; Proaño, Carolina; Takekawa, John Y.; Newman, Scott H.; Waldenström, Jonas; Bengtsson, Daniel; Kays, Roland; Wikelski, Martin; Bohrer, Gil

2013-01-01

Background: Understanding how environmental conditions, especially wind, influence birds' flight speeds is a prerequisite for understanding many important aspects of bird flight, including optimal migration strategies, navigation, and compensation for wind drift. Recent developments in tracking technology and the increased availability of data on large-scale weather patterns have made it possible to use path annotation to link the location of animals to environmental conditions such as wind speed and direction. However, there are various measures available for describing not only wind conditions but also the bird's flight direction and ground speed, and it is unclear which is best for determining the amount of wind support (the length of the wind vector in a bird’s flight direction) and the influence of cross-winds (the length of the wind vector perpendicular to a bird’s direction) throughout a bird's journey.Results: We compared relationships between cross-wind, wind support and bird movements, using path annotation derived from two different global weather reanalysis datasets and three different measures of direction and speed calculation for 288 individuals of nine bird species. Wind was a strong predictor of bird ground speed, explaining 10-66% of the variance, depending on species. Models using data from different weather sources gave qualitatively similar results; however, determining flight direction and speed from successive locations, even at short (15 min intervals), was inferior to using instantaneous GPS-based measures of speed and direction. Use of successive location data significantly underestimated the birds' ground and airspeed, and also resulted in mistaken associations between cross-winds, wind support, and their interactive effects, in relation to the birds' onward flight.Conclusions: Wind has strong effects on bird flight, and combining GPS technology with path annotation of weather variables allows us to quantify these effects for

Validation of the conceptual research utilization scale: an application of the standards for educational and psychological testing in healthcare

Science.gov (United States)

2011-01-01

Background There is a lack of acceptable, reliable, and valid survey instruments to measure conceptual research utilization (CRU). In this study, we investigated the psychometric properties of a newly developed scale (the CRU Scale). Methods We used the Standards for Educational and Psychological Testing as a validation framework to assess four sources of validity evidence: content, response processes, internal structure, and relations to other variables. A panel of nine international research utilization experts performed a formal content validity assessment. To determine response process validity, we conducted a series of one-on-one scale administration sessions with 10 healthcare aides. Internal structure and relations to other variables validity was examined using CRU Scale response data from a sample of 707 healthcare aides working in 30 urban Canadian nursing homes. Principal components analysis and confirmatory factor analyses were conducted to determine internal structure. Relations to other variables were examined using: (1) bivariate correlations; (2) change in mean values of CRU with increasing levels of other kinds of research utilization; and (3) multivariate linear regression. Results Content validity index scores for the five items ranged from 0.55 to 1.00. The principal components analysis predicted a 5-item 1-factor model. This was inconsistent with the findings from the confirmatory factor analysis, which showed best fit for a 4-item 1-factor model. Bivariate associations between CRU and other kinds of research utilization were statistically significant (p use, and longitudinal work to determine CRU Scale sensitivity to change. PMID:21595888

Intelligent control for large-scale variable speed variable pitch wind turbines

Institute of Scientific and Technical Information of China (English)

Xinfang ZHANG; Daping XU; Yibing LIU

2004-01-01

Large-scale wind turbine generator systems have strong nonlinear multivariable characteristics with many uncertain factors and disturbances.Automatic control is crucial for the efficiency and reliability of wind turbines.On the basis of simplified and proper model of variable speed variable pitch wind turbines,the effective wind speed is estimated using extended Kalman filter.Intelligent control schemes proposed in the paper include two loops which operate in synchronism with each other.At below-rated wind speed,the inner loop adopts adaptive fuzzy control based on variable universe for generator torque regulation to realize maximum wind energy capture.At above-rated wind speed, a controller based on least square support vector machine is proposed to adjust pitch angle and keep rated output power.The simulation shows the effectiveness of the intelligent control.

Smal-Scale Spatial Differences in Supply-Side Ecology of Barnacle Larvae Involves a Complex Suite of Factors (Including Surface Tide, Internal Tides And Surface Winds) in Baja California

Science.gov (United States)

Valencia, A.; Ladah, L. B.

2016-02-01

The objective of this study was to quantify and compare the daily settlement rate of barnacle larvae of Chthamalus spp. at small spatial scales ( 1 km) at three sites with unique geomorphology. Simultaneously, water-column temperature, currents, and coastal winds were measured to detect potential physical transport mechanisms responsible for supply of planktonic larvae to the coast. Autocorrelation artifacts in the environmental and settlement time series were removed with the Autoregressive Integrated Moving Average (ARIMA) and their residuals were used to perform a Principal Component Analysis (PCA). This analysis was carried out to determine the independent modes of variability in the environmental forcing mechanisms that may explain the settlement patterns. We found synchronous settlement pulses occurring throughout the study. Settlement at the wave exposed site was only associated to the wind-forcing mode and not to internal waves, which had not been detected previously and was surprising, considering the strong semidiurnal internal tide at this site. Settlement at both the reef-bounded site and the inside-bay site associated to vertical isotherm displacements, thereby suggesting the importance of internal waves for supply-side ecology at these more southern sites. Our results suggest that a complex suite of factors may interact to result in larval supply at the same site, and that larval supply at nearby sites may be forced by different factors due to differences in geomorphology and/or bathymetry, explaining spatial heterogeneity often detected in larval supply and settlement.

Nonlinear internal gravity waves and their interaction with the mean wind

International Nuclear Information System (INIS)

Grimshaw, R.

1975-01-01

The interaction of a wave packet of internal gravity waves with the mean wind is investigated, for the case when there is a region of wind shear and hence a critical level. The principal equations are the Doppler-shifted dispersion relation, the equation for conservation of wave action and the mean momentum equation, in which the mean wind is accelerated by a 'radiation stress' tensor, due to the waves. These equations are integrated numerically to study the behaviour of a wave packet approaching a critical level, where the horizontal phase speed matches the mean wind. The results demonstrate the exchange of energy from the waves to the mean wind in the vicinity of the critical level. The interaction between the waves and the mean wind is also studied in the absence of any initial wind shear. (author)

Wind Energy Resource Atlas of Sri Lanka and the Maldives

Energy Technology Data Exchange (ETDEWEB)

Elliott, D.; Schwartz, M.; Scott, G.; Haymes, S.; Heimiller, D.; George, R.

2003-08-01

The Wind Energy Resource Atlas of Sri Lanka and the Maldives, produced by the National Renewable Energy Laboratory's (NREL's) wind resource group identifies the wind characteristics and distribution of the wind resource in Sri Lanka and the Maldives. The detailed wind resource maps and other information contained in the atlas facilitate the identification of prospective areas for use of wind energy technologies, both for utility-scale power generation and off-grid wind energy applications.

Electricity network limitations on large-scale deployment of wind energy

Energy Technology Data Exchange (ETDEWEB)

Fairbairn, R.J.

1999-07-01

This report sought to identify limitation on large scale deployment of wind energy in the UK. A description of the existing electricity supply system in England, Scotland and Wales is given, and operational aspects of the integrated electricity networks, licence conditions, types of wind turbine generators, and the scope for deployment of wind energy in the UK are addressed. A review of technical limitations and technical criteria stipulated by the Distribution and Grid Codes, the effects of system losses, and commercial issues are examined. Potential solutions to technical limitations are proposed, and recommendations are outlined.

Integration of wind generation forecasts. Volume 2

International Nuclear Information System (INIS)

Ahlstrom, M.; Zavadil, B.; Jones, L.

2005-01-01

WindLogics is a company that specializes in atmospheric modelling, visualization and fine-scale forecasting systems for the wind power industry. A background of the organization was presented. The complexities of wind modelling were discussed. Issues concerning location and terrain, shear, diurnal and interannual variability were reviewed. It was suggested that wind power producers should aim to be mainstream, and that variability should be considered as intrinsic to fuel supply. Various utility operating impacts were outlined. Details of an Xcel NSP wind integration study were presented, as well as a studies conducted in New York state and Colorado. It was concluded that regulations and load following impacts with wind energy integration are modest. Overall impacts are dominated by costs incurred to accommodate wind generation variability and uncertainty in the day-ahead time frame. Cost impacts can be reduced with adjustments to operating strategies, improvements in wind forecasting and access to real-time markets. Details of WindLogic's wind energy forecast system were presented, as well as examples of day ahead and hour ahead forecasts and wind speed and power forecasts. Screenshots of control room integration, EMS integration and simulations were presented. Details of a utility-scale wind energy forecasting system funded by Xcel Renewable Development Fund (RDF) were also presented. The goal of the system was to optimize the way that wind forecast information is integrated into the control room environment. Project components were outlined. It was concluded that accurate day-ahead forecasting can lead to significant asset optimization. It was recommended that wind plants share data, and aim to resolve issues concerning grid codes and instrumentation. refs., tabs., figs

Large-Eddy Simulation of Waked Turbines in a Scaled Wind Farm Facility

Science.gov (United States)

Wang, J.; McLean, D.; Campagnolo, F.; Yu, T.; Bottasso, C. L.

2017-05-01

The aim of this paper is to present the numerical simulation of waked scaled wind turbines operating in a boundary layer wind tunnel. The simulation uses a LES-lifting-line numerical model. An immersed boundary method in conjunction with an adequate wall model is used to represent the effects of both the wind turbine nacelle and tower, which are shown to have a considerable effect on the wake behavior. Multi-airfoil data calibrated at different Reynolds numbers are used to account for the lift and drag characteristics at the low and varying Reynolds conditions encountered in the experiments. The present study focuses on low turbulence inflow conditions and inflow non-uniformity due to wind tunnel characteristics, while higher turbulence conditions are considered in a separate study. The numerical model is validated by using experimental data obtained during test campaigns conducted with the scaled wind farm facility. The simulation and experimental results are compared in terms of power capture, rotor thrust, downstream velocity profiles and turbulence intensity.

Aspects of the determination of winds by means of scatterometry and of the utilization of vector wind data for meteorological forecasts

Science.gov (United States)

Pierson, W. J., Jr.; Sylvester, W. B.; Donelan, M. A.

1986-01-01

The present paper provides a description of four aspects of scatterometer winds and their uses. The theory of wave generation by the wind is considered along with an analysis of the properties of superobservations, and studies of intermittent versus continuous data assimilation methods for numerical weather predictions which use remotely sensed data. A comparison of the sum of squares versus the maximum likelihood method for recovering the vector winds is also conducted. Questions regarding wind speed, friction velocity, or normal stress are discussed and synoptic scale fields from Seasat-SASS data are examined.

Active Subspaces for Wind Plant Surrogate Modeling

Energy Technology Data Exchange (ETDEWEB)

King, Ryan N [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Quick, Julian [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dykes, Katherine L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Adcock, Christiane [Massachusetts Institute of Technology

2018-01-12

Understanding the uncertainty in wind plant performance is crucial to their cost-effective design and operation. However, conventional approaches to uncertainty quantification (UQ), such as Monte Carlo techniques or surrogate modeling, are often computationally intractable for utility-scale wind plants because of poor congergence rates or the curse of dimensionality. In this paper we demonstrate that wind plant power uncertainty can be well represented with a low-dimensional active subspace, thereby achieving a significant reduction in the dimension of the surrogate modeling problem. We apply the active sub-spaces technique to UQ of plant power output with respect to uncertainty in turbine axial induction factors, and find a single active subspace direction dominates the sensitivity in power output. When this single active subspace direction is used to construct a quadratic surrogate model, the number of model unknowns can be reduced by up to 3 orders of magnitude without compromising performance on unseen test data. We conclude that the dimension reduction achieved with active subspaces makes surrogate-based UQ approaches tractable for utility-scale wind plants.

International wind energy development. World market update 1998. Forecast 1999-2003

International Nuclear Information System (INIS)

1999-03-01

This is the fourth issue of the annual World Market Update from BTM Consult ApS, covering the year 1998. All figures in the status part refer to end of the year 1998, the past 3 years development is also assessed and the forecast looks 5 years ahead. The most significant figures and trends in 1998 were: The marketplace - The annual installation of new wind power capacity increased by 55% resulting in a cumulative installation by the end of 1998 of 10.153 MW. 1.766 MW was installed in Europe and the region is still the leading market regarding utilization of wind energy. The US market took a rapid pace and installed 577 MW during the year. The large Enron Wind Corp has taken the larger part of this market. On the supply side Danish NEG Micon A/S has consolidated the position as being the supplier of the most MW wind capacity in the world and the company has a world market share of 23,5 per cent. The company acquired the Danish Wind World af 1997 A/S which was among the larger companies in 1997. Also the Dutch manufacturer NedWind B.V. was acquired by NEG Micon A/S curing 1998. The group of 'other' manufactureres represents a minor percentage of deliveries than earlier and concentration in the industry seems to continue. The liberalized Energy Market and how to position the industry in this different economic environment will be a challenge for the wind industry way into the next century. In Europe, the European Commission's draft Directive with proposal for an outline of common rules for support of among other renewables wind energy has been set on another route which seems to delay the paper. In the US there are still hopes for a new period with PTC (Production Tax Credit). There are in some States hopes among the wind energy people that the 'Green Market Programs' will play a more dominant role in the future. In Asia the crises seems to halt the wind power development. Forecast and Technical trends - Based on the positive trends in the markets for wind power

HFSB-seeding for large-scale tomographic PIV in wind tunnels

Science.gov (United States)

Caridi, Giuseppe Carlo Alp; Ragni, Daniele; Sciacchitano, Andrea; Scarano, Fulvio

2016-12-01

A new system for large-scale tomographic particle image velocimetry in low-speed wind tunnels is presented. The system relies upon the use of sub-millimetre helium-filled soap bubbles as flow tracers, which scatter light with intensity several orders of magnitude higher than micron-sized droplets. With respect to a single bubble generator, the system increases the rate of bubbles emission by means of transient accumulation and rapid release. The governing parameters of the system are identified and discussed, namely the bubbles production rate, the accumulation and release times, the size of the bubble injector and its location with respect to the wind tunnel contraction. The relations between the above parameters, the resulting spatial concentration of tracers and measurement of dynamic spatial range are obtained and discussed. Large-scale experiments are carried out in a large low-speed wind tunnel with 2.85 × 2.85 m2 test section, where a vertical axis wind turbine of 1 m diameter is operated. Time-resolved tomographic PIV measurements are taken over a measurement volume of 40 × 20 × 15 cm3, allowing the quantitative analysis of the tip-vortex structure and dynamical evolution.

Proceedings of the third biennial conference and workshop on wind energy conversion systems. Volume I

Energy Technology Data Exchange (ETDEWEB)

Kornreich, T R [ed.

1978-05-01

Separate abstracts are included for 38 papers presented concerning large scale wind systems, small scale wind systems, regional and economic analysis, wind characteristics research, environmental and institutional considerations, and international activities. Four papers were previously input into the energy data base.

DESIGN AND DEVELOPMENT OF A 1/3 SCALE VERTICAL AXIS WIND TURBINE FOR ELECTRICAL POWER GENERATION

Directory of Open Access Journals (Sweden)

Altab Md. Hossain

2007-12-01

Full Text Available This research describes the electrical power generation in Malaysia by the measurement of wind velocity acting on the wind turbine technology. The primary purpose of the measurement over the 1/3 scaled prototype vertical axis wind turbine for the wind velocity is to predict the performance of full scaled H-type vertical axis wind turbine. The electrical power produced by the wind turbine is influenced by its two major part, wind power and belt power transmission system. The blade and the drag area system are used to determine the powers of the wind that can be converted into electric power as well as the belt power transmission system. In this study both wind power and belt power transmission system has been considered. A set of blade and drag devices have been designed for the 1/3 scaled wind turbine at the Thermal Laboratory of Faculty of Engineering, Universiti Industri Selangor (UNISEL. Test has been carried out on the wind turbine with the different wind velocities of 5.89 m/s, 6.08 m/s and 7.02 m/s. From the experiment, the wind power has been calculated as 132.19 W, 145.40 W and 223.80 W. The maximum wind power is considered in the present study.

DESIGN AND DEVELOPMENT OF A 1/3 SCALE VERTICAL AXIS WIND TURBINE FOR ELECTRICAL POWER GENERATION

Directory of Open Access Journals (Sweden)

Altab Hossain

2007-01-01

Full Text Available This research describes the electrical power generation in Malaysia by the measurement of wind velocity acting on the wind turbine technology. The primary purpose of the measurement over the 1/3 scaled prototype vertical axis wind turbine for the wind velocity is to predict the performance of full scaled H-type vertical axis wind turbine. The electrical power produced by the wind turbine is influenced by its two major part, wind power and belt power transmission system. The blade and the drag area system are used to determine the powers of the wind that can be converted into electric power as well as the belt power transmission system. In this study both wind power and belt power transmission system has been considered. A set of blade and drag devices have been designed for the 1/3 scaled wind turbine at the Thermal Laboratory of Faculty of Engineering, Universiti Industri Selangor (UNISEL. Test has been carried out on the wind turbine with the different wind velocities of 5.89 m/s, 6.08 m/s and 7.02 m/s. From the experiment, the wind power has been calculated as 132.19 W, 145.40 W and 223.80 W. The maximum wind power is considered in the present study.

International co-operation in the field of wind energy

Energy Technology Data Exchange (ETDEWEB)

Wolff, J. [VTT Energy, Espoo (Finland)

1998-10-01

The use of wind energy is expanding rapidly worldwide. At the end of 1996 over 6000 MW was installed and the annual increase has during the last years exceeded 1000 MW. The development is also reaching more and more countries. In order to maintain technical and commercial development international co-operation is needed to secure cost-effectiveness, reliability and safety of the technology. International recommendations, harmonisation and standardisation is promoted by several international organizations like IEA, IEC and the classification organisations

WindPACT Turbine Design Scaling Studies: Technical Area 4 - Balance-of-Station Cost; ANNUAL

International Nuclear Information System (INIS)

Shafer, D. A.; Strawmyer, K. R.; Conley, R. M.; Guidinger J. H.; Wilkie, D. C.; Zellman, T. F.

2001-01-01

DOE's Wind Partnerships for Advanced Component Technologies (WindPACT) program explores the most advanced wind-generating technologies for improving reliability and decreasing energy costs. The first step in the WindPact program is a scaling study to bound the optimum sizes for wind turbines, to define size limits for certain technologies, and to scale new technologies. The program is divided into four projects: Composite Blades for 80-120-meter Rotors; Turbine, Rotor, and Blade Logistics; Self-Erecting Tower and Nacelle Feasibility; and Balance-of-Station Cost. This report discusses balance-of-station costs, which includes the electrical power collector system, wind turbine foundations, communications and controls, meteorological equipment, access roadways, crane pads, and the maintenance building. The report is based on a conceptual 50-megawatt (MW) wind farm site near Mission, South Dakota. Cost comparisons are provided for four sizes of wind turbines: 750 kilowatt (kW), 2.5 MW, 5.0 MW, and 10.0 MW

International Symposium on Wind Energy Systems, 4th, Stockholm, Sweden, September 21-24, 1982, Proceedings. Volumes 1 & 2

Science.gov (United States)

Stephens, H. S.; Goodes, D. H.

Progress in theoretical, meteorological, and hardware development sectors of wind energy utilization is assessed for various national programs. Wind regime characterization studies in Agentina, China, Indonesia, Norway, the U.S., Canada, Sweden, Hawaii, and offshore of the U.K. are reported. Data gained from wind turbine test sites in the U.S., Denmark, Holland, Germany, and the Netherlands are outlined. Attention is focused on the economics of wind turbine production for utility, agricultural, and third party purposes, with mention made of utilizing the resource appropriately for areas of installation of the wind powered machinery. Analyses are made of diurnal wind variations compared to diurnal demands on conventinal electricity generating power stations. Performance projections are made for wind farms featuring multi-MW machines, taking into account grid inteconnection factors, electrical control, power ramps, and environmental considerations. Mention is made of aeroelastics, dynamics, and the aerodynamics of wind turbines and rotor blades. Finally, icing, noise, fatigue failure, and blade throw problem are discussed, together with wind turbine licensing procedures in Denmark. No invidivual items are abstracted in these volumes

Economic scale of utilization of radiation in Japan

International Nuclear Information System (INIS)

Yanagisawa, Kazuaki; Kume, Tamikazu; Makuuchi, Keizo

2001-01-01

Economic scale, not benefits, of utilization of radiation in Japan in 1997 was estimated without use of any calculation code. The objects were industrial usage, agricultural application and medical utilization. In the third item, the scale was the expense of medical use in patients of radiation generating apparatuses, of which production was regarded as belonging to the first item. The scale was found to be around 8,569,900,000,000 (8,569.9b) yen, of which 85% was in industry, 1% in agriculture and 14% in medicine, and to be about 1.7% GDP (General Domestic Products). In industry, its 75% was in manufacturing the semi-conductor. Medical use (91% of whole medicine) involved roentgenography (47%), CT (37%), nuclear medicine (12%) and radiotherapy (5%). The scale of radioisotope utilization was 65.4b yen in industry, 0.16b yen in agriculture and 1.1b yen in medicine of which 53% was due to 60 Co. If adding the scale of atomic energy utilization (7,274.2b yen) to above, 15,844.1b yen (3.2% GDP) was the total scale of atomic power utilization. (K.H.)

Power System Operation with Large-Scale Wind Power in Liberalised Environments

International Nuclear Information System (INIS)

Ummels, B.C.

2009-01-01

The disadvantages of producing electricity from fossil fuels are that their supply is finite and unevenly distributed across the earth. Conventional power stations also emit greenhouse gases. Therefore, sustainable alternatives must be developed, such as wind power. The disadvantages of wind are that it may or may not blow and that it is unpredictable. Th generation of electricity must however always equal the consumption. This makes the integration of wind power in the electricity system more difficult. This thesis investigates the integration of wind power into the existing power system. Simulation models are developed and used to explore the operation of power systems with a lot of wind power. The simulations provide a picture of the reliability, cost and emission of CO2 of the generation of electricity, with and without wind power. The research also takes into account electricity exchange on international markets. Possible solutions for integrating wind power, such as flexible power plants and energy storage, are investigated as well

Basin-scale wind transport during the MILAGRO field campaign and comparison to climatology using cluster analysis

Directory of Open Access Journals (Sweden)

B. de Foy

2008-03-01

Full Text Available The MILAGRO field campaign was a multi-agency international collaborative project to evaluate the regional impacts of the Mexico City air pollution plume as a means of understanding urban impacts on the global climate. Mexico City lies on an elevated plateau with mountains on three sides and has complex mountain and surface-driven wind flows. This paper asks what the wind transport was in the basin during the field campaign and how representative it was of the climatology. Surface meteorology and air quality data, radiosondes and radar wind profiler data were collected at sites in the basin and its vicinity. Cluster analysis was used to identify the dominant wind patterns both during the campaign and within the past 10 years of operational data from the warm dry season. Our analysis shows that March 2006 was representative of typical flow patterns experienced in the basin. Six episode types were identified for the basin-scale circulation providing a way of interpreting atmospheric chemistry and particulate data collected during the campaign. Decoupling between surface winds and those aloft had a strong influence in leading to convection and poor air quality episodes. Hourly characterisation of wind circulation during the MILAGRO, MCMA-2003 and IMADA field campaigns enables the comparisons of similar air pollution episodes and the evaluation of the impact of wind transport on measurements of the atmospheric chemistry taking place in the basin.

Accident of Large-scale Wind Turbines Disconnecting from Power Grid and Its Protection

Institute of Scientific and Technical Information of China (English)

2012-01-01

There were many accidents of large-scale wind turbines disconnecting from power grid in 2011. As single- phase-to-ground fault cannot be correctly detected, single-phase-to-ground fault evolved to phase-to-phase fault. Phase-to-phase fault was isolated slowly, thus leading to low voltage. And wind turbines without enough low voltage ride-through capacity had to be disconnected from the grid. After some wind turbines being disconnected from the grid, overvoltage caused by reactive power surplus made more wind turbines disconnect from the grid. Based on the accident analysis, this paper presents solutions to above problems, including travelling waves based single-phase-to-ground protection, adaptive low voltage protection, integrated protection and control, and high impedance fault detection. The solutions lay foundations in theory and technology to prevent large-scale wind turbines disconnecting from the operating power grid.

Electric vehicles and large-scale integration of wind power

DEFF Research Database (Denmark)

Liu, Wen; Hu, Weihao; Lund, Henrik

2013-01-01

with this imbalance and to reduce its high dependence on oil production. For this reason, it is interesting to analyse the extent to which transport electrification can further the renewable energy integration. This paper quantifies this issue in Inner Mongolia, where the share of wind power in the electricity supply...... was 6.5% in 2009 and which has the plan to develop large-scale wind power. The results show that electric vehicles (EVs) have the ability to balance the electricity demand and supply and to further the wind power integration. In the best case, the energy system with EV can increase wind power...... integration by 8%. The application of EVs benefits from saving both energy system cost and fuel cost. However, the negative consequences of decreasing energy system efficiency and increasing the CO2 emission should be noted when applying the hydrogen fuel cell vehicle (HFCV). The results also indicate...

How to correct long-term system externality of large scale wind power development by a capacity mechanism?

International Nuclear Information System (INIS)

Cepeda, Mauricio; Finon, Dominique

2013-04-01

This paper deals with the practical problems related to long-term security of supply in electricity markets in the presence of large-scale wind power development. The success of renewable promotion schemes adds a new dimension to ensuring long-term security of supply. It necessitates designing second-best policies to prevent large-scale wind power development from distorting long-run equilibrium prices and investments in conventional generation and in particular in peaking units. We rely upon a long-term simulation model which simulates electricity market players' investment decisions in a market regime and incorporates large-scale wind power development either in the presence of either subsidised wind production or in market-driven development. We test the use of capacity mechanisms to compensate for the long-term effects of large-scale wind power development on the system reliability. The first finding is that capacity mechanisms can help to reduce the social cost of large scale wind power development in terms of decrease of loss of load probability. The second finding is that, in a market-based wind power deployment without subsidy, wind generators are penalized for insufficient contribution to the long term system's reliability. (authors)

Wind energy mission analysis. Executive summary. [USA

Energy Technology Data Exchange (ETDEWEB)

1977-02-18

The principal objectives of this study were (1) to assess the potential for wind energy conversion systems on a national scale, (2) identify high-potential applications for WECS, (3) define functional, performance, operational, and cost goals for WECS, (4) evaluate the impact of the wide-scale deployment of WECS on energy users, and (5) identify the institutional and non-technical problems associated with the acceptance of wind energy systems. The study concentrated on broad applications of WECS over large geographic areas encompassing the entire United States. Emphasis was placed on identifying and exploring high-aggregate energy users who have significant potential to utilize wind energy in place of other alternatives.

Diffusing wind energy : a review of best-practice development in Ontario

Energy Technology Data Exchange (ETDEWEB)

Cone, C.G. [Calgary Univ., AB (Canada)

2008-07-01

Public and community acceptance of large-scale wind development will play a large role in its deployment and growth in Canada. However, proponents must consider the socio-economic and environmental impacts of wind power on communities in order to ensure the industry's continued growth. Best practices are needed ensure that all wind power projects develop constructive relationships with governments, public utilities, and communities. Wind power proponents must learn to engage with the emotional, environmental, and economic needs of communities. Developers must consider the fact that many members of the public are misinformed about potential noise levels and the impacts of wind turbines on local wildlife. Successful wind power projects have worked to establish trust and open communications with communities who have been fully informed of the scale of the development and its potential economic and environmental consequences. It was concluded that unsuccessful projects have relied solely on governments and utilities to inform community members about the impacts of wind power, and have tended to focus almost exclusively on issues related to technology and construction. tabs., figs.

Pilot-scale concept of real-time wind speed-matching wind tunnel for measurements of gaseous emissions

Science.gov (United States)

Comprehensive control of odors, hydrogen sulfide (H2S), ammonia (NH3) and odorous volatile organic compound (VOC) emissions associated with animal production is a critical need. Current methods utilizing wind tunnels and flux chambers for measurements of gaseous emissions from area sources such as f...

Financing small scale wind energy projects in the UK

International Nuclear Information System (INIS)

Mitchell, Catherine

1993-01-01

This paper shows how wind energy projects in the UK have obtained finance. It attempts to list the financing options open to small scale developments and to note any likely problems which may occur. (UK)

WindPACT Turbine Design Scaling Studies Technical Area 2: Turbine, Rotor and Blade Logistics; TOPICAL

International Nuclear Information System (INIS)

Smith, K.

2001-01-01

Through the National Renewable Energy Laboratory (NREL), the United States Department of Energy (DOE) implemented the Wind Partnership for Advanced Component Technologies (WindPACT) program. This program will explore advanced technologies that may reduce the cost of energy (COE) from wind turbines. The initial step in the WindPACT program is a series of preliminary scaling studies intended to determine the optimum sizes for future turbines, help define sizing limits for certain critical technologies, and explore the potential for advanced technologies to contribute to reduced COE as turbine scales increase. This report documents the results of Technical Area 2-Turbine Rotor and Blade Logistics. For this report, we investigated the transportation, assembly, and crane logistics and costs associated with installation of a range of multi-megawatt-scale wind turbines. We focused on using currently available equipment, assembly techniques, and transportation system capabilities and limitations to hypothetically transport and install 50 wind turbines at a facility in south-central South Dakota

The International Energy Agency`s role in world-wide wind energy development

Energy Technology Data Exchange (ETDEWEB)

Rangi, R. [Natural Resources Canada, Ottawa, Ontario (Canada); Ancona, D. [Dept. of Energy, Washington, DC (United States)

1997-12-31

Wind energy is now being deployed world-wide at a rapidly increasing rate and the International Energy Agency (IEA) has a changing role in its growth. IEA was founded in 1974 within the framework of the Organization for Economic Cooperation and Development (OECD) to collaborate on comprehensive international energy programs. IEA membership consists of eighteen parties from sixteen countries and the European Commission. Recently there has been increasing interest in IEA participation from both OECD and non-OECD countries. Non-OECD countries participating in various IEA Agreements include: China, India, Israel, Korea, and Russia. Because of its diverse international makeup, the IEA is viewed as a source of reliable technical and economic information. The World Bank has approached the Executive Committee for Wind Energy R & D, through the IEA Renewable Energy Working Party, to assist in the expansion of wind deployment. In addition, IEA is moving from R & D programs to include tracking of implementation incentives offered by its members.

Internal Consistency, Retest Reliability, and their Implications For Personality Scale Validity

Science.gov (United States)

McCrae, Robert R.; Kurtz, John E.; Yamagata, Shinji; Terracciano, Antonio

2010-01-01

We examined data (N = 34,108) on the differential reliability and validity of facet scales from the NEO Inventories. We evaluated the extent to which (a) psychometric properties of facet scales are generalizable across ages, cultures, and methods of measurement; and (b) validity criteria are associated with different forms of reliability. Composite estimates of facet scale stability, heritability, and cross-observer validity were broadly generalizable. Two estimates of retest reliability were independent predictors of the three validity criteria; none of three estimates of internal consistency was. Available evidence suggests the same pattern of results for other personality inventories. Internal consistency of scales can be useful as a check on data quality, but appears to be of limited utility for evaluating the potential validity of developed scales, and it should not be used as a substitute for retest reliability. Further research on the nature and determinants of retest reliability is needed. PMID:20435807

A New Building-Integrated Wind Turbine System Utilizing the Building

Directory of Open Access Journals (Sweden)

Jeongsu Park

2015-10-01

Full Text Available This paper proposes an innovative building-integrated wind turbine (BIWT system by directly utilizing the building skin, which is an unused and unavailable area in all conventional BIWT systems. The proposed system has been developed by combining a guide vane that is able to effectively collect the incoming wind and increase its speed and a rotor with an appropriate shape for specific conditions. To this end, several important design issues for the guide vane as well as the rotor were thoroughly investigated and accordingly addressed in this paper. A series of computational fluid dynamics (CFD analyses was performed to determine the optimal configuration of the proposed system. Finally, it is demonstrated from performance evaluation tests that the prototype with the specially designed guide vane and rotor for the proposed BIWT system accelerates the wind speed to a sufficient level and consequently increases the power coefficient significantly. Thus, it was confirmed that the proposed system is a promising environment-friendly energy production system for urban areas.

Meso-scale wind variability. Final report

Energy Technology Data Exchange (ETDEWEB)

Larsen, S.; Larsen, X.; Vincent, C.; Soerensen, P.; Pinson, P.; Trombe, P.-J.; Madsen, H.; Cutululis, N.

2011-11-15

The project has aimed to characterize mesoscale meteorological phenomenon for the North Sea and the Inner Danish waters, and additionally aimed on improving the predictability and quality of the power production from offshore windfarms. The meso-scale meteorology has been characterized with respect to the physical processes, climatology, spectral characteristics and correlation properties based on measurements from wind farms, satellite data (SAR) and mesoscale numerical modeling (WRF). The abilities of the WRF model to characterize and predict relevant mesoscale phenomenon has been proven. Additionally application of statistical forecasting, using a Markov switching approach that can be related to the meteorological conditions, to analyze and short term predict the power production from an offshore wind farms have been documented. Two PhD studies have been conducted in connection with the project. The project has been a cooperative project between Risoe DTU, IMM DTU, DONG Energy, Vattenfall and VESTAS. It is registered as Energinet.dk, project no. 2007-1-7141. (Author)

NEMO 2 - Be aware: Wind and solar are coming

Energy Technology Data Exchange (ETDEWEB)

Lund, P. [Helsinki Univ. of Technology, Otaniemi (Finland)

1996-12-31

Finnish research and development is well placed with respect to new renewable energy technologies in that there exists considerable expertise in specialized areas. For example, over 20 % of all power transmission equipment and generators used in wind energy systems world-wide are manufactured in Finland, while advanced instruments for monitoring wind speed are also highly regarded internationally. Moreover, unique wind technology for complex windy and freezing conditions have been developed. Finland has a 10 % share in the European photovoltaic market, and has competitive advantages in photovoltaic systems and applications, thin film solar cells, and automated electronic controlling systems. A unique solar energy storage system based on hydrogen technology demonstrates skills on overcoming the summer-winter syndrome of large-scale solar energy utilization. The annual turnover of the Finnish industries on solar and wind energy has increased from 5 million ECU in 1988 to almost 50 million ECU in 1996. The national R and D and D from 1988 onwards has played an important role in this context. Most of the research and development into new and renewable energy technologies in Finland has been carried out through the Advanced New Energy Systems and Technologies Research Programme (NEMO2) of Tekes

The Feasibility of Utilizing Wind Energy in Commercial Buildings With Special Reference to the Kingdom of Bahrain

Science.gov (United States)

Abdulrahim Saeed, Saeed

2017-11-01

This article shall investigate the feasibility of utilizing wind energy for commercial buildings with special reference to the Kingdom of Bahrain. Bahrain World Trade Center which was built in 2008, is located in the city of Manama. The fifty-story complex contains identical twin towers that rise over 240 meters in height. The towers are connected by three bridges which hold three turbines each 29 meters long. The three turbines were originally design to provide electric energy required for lighting. The Bahrain World Trade Center was selected as a case study to investigate the feasibility of utilizing wind energy technologies in skyscrapers with special reference to the Kingdom of Bahrain. It is hoped that the findings and conclusion of the study shall be of some value for future utilization of wind energy in the GCC countries and the world at large.

Bi-Level Decentralized Active Power Control for Large-Scale Wind Farm Cluster

DEFF Research Database (Denmark)

Huang, Shengli; Wu, Qiuwei; Guo, Yifei

2018-01-01

This paper presents a bi-level decentralized active power control (DAPC) for a large-scale wind farm cluster, consisting of several wind farms for better active power dispatch. In the upper level, a distributed active power control scheme based on the distributed consensus is designed to achieve...... fair active power sharing among multiple wind farms, which generates the power reference for each wind farm. A distributed estimator is used to estimate the total available power of all wind farms. In the lower level, a centralized control scheme based on the Model Predictive Control (MPC) is proposed...... to regulate active power outputs of all wind turbines (WTs) within a wind farm, which reduces the fatigue loads of WTs while tracking the power reference obtained from the upper level control. A wind farm cluster with 8 wind farms and totally 160 WTs, was used to test the control performance of the proposed...

How to correct for long-term externalities of large-scale wind power development by a capacity mechanism?

International Nuclear Information System (INIS)

Cepeda, Mauricio; Finon, Dominique

2013-01-01

This paper deals with the practical problems related to long-term security of supply in electricity markets in the presence of large-scale wind power development. The success of recent renewable promotion schemes adds a new dimension to ensuring long-term security of supply: it necessitates designing second-best policies to prevent large-scale wind power development from distorting long-run equilibrium prices and investments in conventional generation and in particular in peaking units. We rely upon a long-term simulation model which simulates electricity market players' investment decisions in a market regime and incorporates large-scale wind power development in the presence of either subsidized or market driven development scenarios. We test the use of capacity mechanisms to compensate for long-term effects of large-scale wind power development on prices and reliability of supply. The first finding is that capacity mechanisms can help to reduce the social cost of large scale wind power development in terms of decrease of loss of load probability. The second finding is that, in a market-based wind power deployment without subsidy, wind generators are penalised for insufficient contribution to the long term system's reliability. - Highlights: • We model power market players’ investment decisions incorporating wind power. • We examine two market designs: an energy-only market and a capacity mechanism. • We test two types of wind power development paths: subsidised and market-driven. • Capacity mechanisms compensate for the externalities of wind power developments

Wind power takes over

International Nuclear Information System (INIS)

2002-01-01

All over the industrialized world concentrated efforts are being made to make wind turbines cover some of the energy demand in the coming years. There is still a long way to go, however, towards a 'green revolution' as far as energy is concerned, for it is quite futile to use wind power for electric heating. The article deals with some of the advantages and disadvantages of developing wind power. In Norway, for instance, environmentalists fear that wind power plants along the coast may have serious consequences for the stocks of white-tailed eagle and golden eagle. An other factor that delays the large-scale application of wind power in Norway is the low price of electricity. Some experts, however, maintain that wind power may already compete with new hydroelectric power of intermediate cost. The investment costs are expected to go down with one third by 2020, when wind power may be the most competitive energy source to utilize

First International Workshop on Grid Simulator Testing of Wind Turbine

Science.gov (United States)

utilities to exchange knowledge, discuss experiences, and identify needs in wind power grid compliance , multi-megawatt power electronic grid simulator systems capable of many types of grid compliance testing renewable energy technologies. Knowledge from the workshop will help guide the research and testing

Scaling Issues in the Determination of Wind loads on Lattice Masts

DEFF Research Database (Denmark)

Koss, Holger; Srouji, Robin G.

2015-01-01

The paper presents a study conducted to investigate the influence of geometric scale and flow condition on the wind load coefficients for lattice masts structures. An initial study in 2008 on a full size mast section indicated a possible contingency, which could be used to add equipment on teleco......The paper presents a study conducted to investigate the influence of geometric scale and flow condition on the wind load coefficients for lattice masts structures. An initial study in 2008 on a full size mast section indicated a possible contingency, which could be used to add equipment...

Small scale wind power harnessing in Colombian oil industry facilities: Wind resource and technology issues

Energy Technology Data Exchange (ETDEWEB)

Giraldo, Mauricio; Nieto, Cesar; Escudero, Ana C.; Cobos, Juan C.; Delgado, Fernando

2010-07-01

Full text: Looking to improve its national and international standing, Colombia's national oil company, Ecopetrol, has set its goal on becoming involved on the production of energy from multiple sources, most importantly, on having an important percentage of its installed capacity from renewable sources. Part of this effort entices the evaluation of wind power potential on its facilities, including production, transportation and administrative, as well as identifying those technologies most suitable for the specific conditions of an equatorial country such as Colombia. Due to the lack of adequate site information, the first step consisted in superimposing national data to the facilities map of the company; this allowed for the selection of the first set of potential sites. From this set, the terminal at Covenas-Sucre was selected taking into account not only wind resource, but ease of access and power needs, as well as having a more or less representative wind potential in comparison to the rest of the country. A weather station was then installed to monitor wind variables. Measurements taken showed high variations in wind direction, and relatively low velocity profiles, making most commercially available wind turbines difficult to implement. In light of the above, a series of iterative steps were taken, first considering a range of individual Vertical Axis Wind Turbines (VAWT), given their capacity to adapt to changing wind directions. However, wind speed variations proved to be a challenge for individual VAWT's, i.e. Darriues turbines do not work well with low wind speeds, and Savonius turbines are not efficient of high wind speeds. As a result, a combined Darrieus- Savonius VAWT was selected given the capacity to adapt to both wind regimes, while at the same time modifying the size and shape of the blades in order to adapt to the lower average wind speeds present at the site. The resulting prototype is currently under construction and is scheduled to

Variability in large-scale wind power generation: Variability in large-scale wind power generation

Energy Technology Data Exchange (ETDEWEB)

Kiviluoma, Juha [VTT Technical Research Centre of Finland, Espoo Finland; Holttinen, Hannele [VTT Technical Research Centre of Finland, Espoo Finland; Weir, David [Energy Department, Norwegian Water Resources and Energy Directorate, Oslo Norway; Scharff, Richard [KTH Royal Institute of Technology, Electric Power Systems, Stockholm Sweden; Söder, Lennart [Royal Institute of Technology, Electric Power Systems, Stockholm Sweden; Menemenlis, Nickie [Institut de recherche Hydro-Québec, Montreal Canada; Cutululis, Nicolaos A. [DTU, Wind Energy, Roskilde Denmark; Danti Lopez, Irene [Electricity Research Centre, University College Dublin, Dublin Ireland; Lannoye, Eamonn [Electric Power Research Institute, Palo Alto California USA; Estanqueiro, Ana [LNEG, Laboratorio Nacional de Energia e Geologia, UESEO, Lisbon Spain; Gomez-Lazaro, Emilio [Renewable Energy Research Institute and DIEEAC/EDII-AB, Castilla-La Mancha University, Albacete Spain; Zhang, Qin [State Grid Corporation of China, Beijing China; Bai, Jianhua [State Grid Energy Research Institute Beijing, Beijing China; Wan, Yih-Huei [National Renewable Energy Laboratory, Transmission and Grid Integration Group, Golden Colorado USA; Milligan, Michael [National Renewable Energy Laboratory, Transmission and Grid Integration Group, Golden Colorado USA

2015-10-25

The paper demonstrates the characteristics of wind power variability and net load variability in multiple power systems based on real data from multiple years. Demonstrated characteristics include probability distribution for different ramp durations, seasonal and diurnal variability and low net load events. The comparison shows regions with low variability (Sweden, Spain and Germany), medium variability (Portugal, Ireland, Finland and Denmark) and regions with higher variability (Quebec, Bonneville Power Administration and Electric Reliability Council of Texas in North America; Gansu, Jilin and Liaoning in China; and Norway and offshore wind power in Denmark). For regions with low variability, the maximum 1 h wind ramps are below 10% of nominal capacity, and for regions with high variability, they may be close to 30%. Wind power variability is mainly explained by the extent of geographical spread, but also higher capacity factor causes higher variability. It was also shown how wind power ramps are autocorrelated and dependent on the operating output level. When wind power was concentrated in smaller area, there were outliers with high changes in wind output, which were not present in large areas with well-dispersed wind power.

A novel vertical-axis wind turbine for distributed and utility deployment

Energy Technology Data Exchange (ETDEWEB)

Park, J.Y. [Inha Univ., Incheon (Korea, Republic of); Lee, S. [Inha Univ., Incheon (Korea, Republic of)]|[KR Wind Energy Research Inst., Incheon (Korea, Republic of); Sabourin, T.; Park, K. [KR Windpower Inc., (United States)

2008-07-01

The rapid growth in the wind power industry can be attributed to energy cost saving, power reliability, grid support, and environmental concerns. Wind turbines should also comply with community noise and aesthetic requirements as well as meet a strong need for high capacity. Wind Turbine Generator Systems are classified as either horizontal axis wind turbine (HAWT) or vertical axis wind turbine (VAWT) depending on whether their axis of rotation is parallel or perpendicular to the ground. The average electric power produced by the wind turbine is proportional to the efficiency of the rotor, air density, projected area of the turbine, and cube of wind speed. The capacity factor should be increased to guarantee the economics of the turbine via increase in the rotor size or the turbine efficiency. The low rotational speed of VAWT rotors suggests that the machine will be quieter than the high-rotational speed of HAWTs, thereby being potentially suitable for applications closer to population centres. The slow rotating machine may also be considered to be visually more aesthetic. This paper presented the measured performance of a small-scale VAWT rated as 1 kW which has a tail consisting of a stabilizer and a rudder. It was tested for its electric power produced at specified wind conditions in an open-type wind tunnel. In order to eliminate the inevitable blockage effect by the size of turbine, the flow deceleration effect of the incoming air to the turbine was analyzed through model testing and numerical simulation and implemented to the proto-type testing. The turbine and its furling tail was shown to be safe. 9 refs., 1 tab., 10 figs.

Scale effects on quasi-steady solid rocket internal ballistic behaviour

Energy Technology Data Exchange (ETDEWEB)

Greatrix, D. R. [Department of Aerospace Engineering, Ryerson University, 350 Victoria Street, Toronto, Ontario, M5B2K3 (Canada)

2010-11-15

The ability to predict with some accuracy a given solid rocket motor's performance before undertaking one or several costly experimental test firings is important. On the numerical prediction side, as various component models evolve, their incorporation into an overall internal ballistics simulation program allows for new motor firing simulations to take place, which in turn allows for updated comparisons to experimental firing data. In the present investigation, utilizing an updated simulation program, the focus is on quasi-steady performance analysis and scale effects (influence of motor size). The predicted effects of negative/positive erosive burning and propellant/casing deflection, as tied to motor size, on a reference cylindrical-grain motor's internal ballistics, are included in this evaluation. Propellant deflection has only a minor influence on the reference motor's internal ballistics, regardless of motor size. Erosive burning, on the other hand, is distinctly affected by motor scale. (author)

Implementation of large-scale average geostrophic wind shear in WAsP12.1

DEFF Research Database (Denmark)

Floors, Rogier Ralph; Troen, Ib; Kelly, Mark C.

The vertical extrapolation model described in the European Wind Atlas Troen and Petersen (1989) is modified to take into account large-scale average geostrophic wind shear to describe the effect of horizontal temperature gradients on the geostrophic wind. The method is implemented by extracting...... the average geostrophic wind shear from Climate Forecast System Reanalysis (CFSR) data and the values of nearest grid point are automatically used in the WAsP 12.1 user interface to provide better AEP predictions....

Short-Term Wind Speed Forecasting for Power System Operations

KAUST Repository

Zhu, Xinxin

2012-04-01

The emphasis on renewable energy and concerns about the environment have led to large-scale wind energy penetration worldwide. However, there are also significant challenges associated with the use of wind energy due to the intermittent and unstable nature of wind. High-quality short-term wind speed forecasting is critical to reliable and secure power system operations. This article begins with an overview of the current status of worldwide wind power developments and future trends. It then reviews some statistical short-term wind speed forecasting models, including traditional time series approaches and more advanced space-time statistical models. It also discusses the evaluation of forecast accuracy, in particular, the need for realistic loss functions. New challenges in wind speed forecasting regarding ramp events and offshore wind farms are also presented. © 2012 The Authors. International Statistical Review © 2012 International Statistical Institute.

Multi-Time Scale Coordinated Scheduling Strategy with Distributed Power Flow Controllers for Minimizing Wind Power Spillage

Directory of Open Access Journals (Sweden)

Yi Tang

2017-11-01

Full Text Available The inherent variability and randomness of large-scale wind power integration have brought great challenges to power flow control and dispatch. The distributed power flow controller (DPFC has the higher flexibility and capacity in power flow control in the system with wind generation. This paper proposes a multi-time scale coordinated scheduling model with DPFC to minimize wind power spillage. Configuration of DPFCs is initially determined by stochastic method. Afterward, two sequential procedures containing day-head and real-time scales are applied for determining maximum schedulable wind sources, optimal outputs of generating units and operation setting of DPFCs. The generating plan is obtained initially in day-ahead scheduling stage and modified in real-time scheduling model, while considering the uncertainty of wind power and fast operation of DPFC. Numerical simulation results in IEEE-RTS79 system illustrate that wind power is maximum scheduled with the optimal deployment and operation of DPFC, which confirms the applicability and effectiveness of the proposed method.

Mini-review of wind energy 1995

International Nuclear Information System (INIS)

1996-01-01

At the 1995 meeting of the International Energy Agency CADDET renewable energy technologies programme, contributors aimed to advise on wind energy use and identify future needs for analysis of future trends and review research tasks. Three major trends leading to the commercial exploitation of wind energy are identified. Firstly, cost reduction and increased efficiency is aimed at through technical innovation, economies of scale and reduced labour costs. The environmental and social benefits of wind energy are acknowledged in the second place. Lastly, wind turbine deployment has been given decisive market incentives. Two major barriers block the development of the wind energy market, availability of site locations and the current economic state of countries likely to espouse wind energy. (UK)

Preview-based Asymmetric Load Reduction of Wind Turbines

DEFF Research Database (Denmark)

Madsen, Mathias; Filsø, Jakob; Soltani, Mohsen

2012-01-01

Controller (MPC) developed is based on a model with individual blade pitching to utilize the LIDAR measurements. The MPC must also maintain a given power reference while satisfying a set of actuator constraints. The designed controller was tested on a 5 MW wind turbine in the FAST simulator and compared......Fatigue loads on wind turbines caused by an asymmetric wind field become an increasing concern when the scale of wind turbines increases. This paper presents a model based predictive approach to reduce asymmetric loads by using Light Detection And Ranging (LIDAR) measurements. The Model Predictive...

TradeWind. Integrating wind. Developing Europe's power market for the large-scale integration of wind power. Final report

Energy Technology Data Exchange (ETDEWEB)

2009-02-15

Based on a single European grid and power market system, the TradeWind project explores to what extent large-scale wind power integration challenges could be addressed by reinforcing interconnections between Member States in Europe. Additionally, the project looks at the conditions required for a sound power market design that ensures a cost-effective integration of wind power at EU level. In this way, the study addresses two issues of key importance for the future integration of renewable energy, namely the weak interconnectivity levels between control zones and the inflexibility and fragmented nature of the European power market. Work on critical transmission paths and interconnectors is slow for a variety of reasons including planning and administrative barriers, lack of public acceptance, insufficient economic incentives for TSOs, and the lack of a joint European approach by the key stakeholders. (au)

Scale Adaptive Simulation Model for the Darrieus Wind Turbine

DEFF Research Database (Denmark)

Rogowski, K.; Hansen, Martin Otto Laver; Maroński, R.

2016-01-01

Accurate prediction of aerodynamic loads for the Darrieus wind turbine using more or less complex aerodynamic models is still a challenge. One of the problems is the small amount of experimental data available to validate the numerical codes. The major objective of the present study is to examine...... the scale adaptive simulation (SAS) approach for performance analysis of a one-bladed Darrieus wind turbine working at a tip speed ratio of 5 and at a blade Reynolds number of 40 000. The three-dimensional incompressible unsteady Navier-Stokes equations are used. Numerical results of aerodynamic loads...

Reliability benefits of dispersed wind resource development

International Nuclear Information System (INIS)

Milligan, M.; Artig, R.

1998-05-01

Generating capacity that is available during the utility peak period is worth more than off-peak capacity. Wind power from a single location might not be available during enough of the peak period to provide sufficient value. However, if the wind power plant is developed over geographically disperse locations, the timing and availability of wind power from these multiple sources could provide a better match with the utility's peak load than a single site. There are other issues that arise when considering disperse wind plant development. Singular development can result in economies of scale and might reduce the costs of obtaining multiple permits and multiple interconnections. However, disperse development can result in cost efficiencies if interconnection can be accomplished at lower voltages or at locations closer to load centers. Several wind plants are in various stages of planning or development in the US. Although some of these are small-scale demonstration projects, significant wind capacity has been developed in Minnesota, with additional developments planned in Wyoming, Iowa and Texas. As these and other projects are planned and developed, there is a need to perform analysis of the value of geographically disperse sites on the reliability of the overall wind plant.This paper uses a production-cost/reliability model to analyze the reliability of several wind sites in the state of Minnesota. The analysis finds that the use of a model with traditional reliability measures does not produce consistent, robust results. An approach based on fuzzy set theory is applied in this paper, with improved results. Using such a model, the authors find that system reliability can be optimized with a mix of disperse wind sites

Wind Generation on Winnebago Tribal Lands

Energy Technology Data Exchange (ETDEWEB)

Multiple

2009-09-30

The Winnebago Wind Energy Study evaluated facility-scale, community-scale and commercial-scale wind development on Winnebago Tribal lands in northeastern Nebraska. The Winnebago Tribe of Nebraska has been pursuing wind development in various forms for nearly ten years. Wind monitoring utilizing loaned met towers from NREL took place during two different periods. From April 2001 to April 2002, a 20-meter met tower monitored wind data at the WinnaVegas Casino on the far eastern edge of the Winnebago reservation in Iowa. In late 2006, a 50-meter tower was installed, and subsequently monitored wind data at the WinnaVegas site from late 2006 through late 2008. Significant challenges with the NREL wind monitoring equipment limited the availability of valid data, but based on the available data, average wind speeds between 13.6 – 14.3 miles were indicated, reflecting a 2+/3- wind class. Based on the anticipated cost of energy produced by a WinnaVegas wind turbine, and the utility policies and rates in place at this time, a WinnaVegas wind project did not appear to make economic sense. However, if substantial grant funding were available for energy equipment at the casino site, and if either Woodbury REC backup rates were lower, or NIPCO was willing to pay more for wind power, a WinnaVegas wind project could be feasible. With funding remaining in the DOE-funded project budget,a number of other possible wind project locations on the Winnebago reservation were considered. in early 2009, a NPPD-owned met tower was installed at a site identified in the study pursuant to a verbal agreement with NPPD which provided for power from any ultimately developed project on the Western Winnebago site to be sold to NPPD. Results from the first seven months of wind monitoring at the Western Winnebago site were as expected at just over 7 meters per second at 50-meter tower height, reflecting Class 4 wind speeds, adequate for commercial development. If wind data collected in the remaining

Variability of the Wind Turbine Power Curve

Directory of Open Access Journals (Sweden)

Mahesh M. Bandi

2016-09-01

Full Text Available Wind turbine power curves are calibrated by turbine manufacturers under requirements stipulated by the International Electrotechnical Commission to provide a functional mapping between the mean wind speed v ¯ and the mean turbine power output P ¯ . Wind plant operators employ these power curves to estimate or forecast wind power generation under given wind conditions. However, it is general knowledge that wide variability exists in these mean calibration values. We first analyse how the standard deviation in wind speed σ v affects the mean P ¯ and the standard deviation σ P of wind power. We find that the magnitude of wind power fluctuations scales as the square of the mean wind speed. Using data from three planetary locations, we find that the wind speed standard deviation σ v systematically varies with mean wind speed v ¯ , and in some instances, follows a scaling of the form σ v = C × v ¯ α ; C being a constant and α a fractional power. We show that, when applicable, this scaling form provides a minimal parameter description of the power curve in terms of v ¯ alone. Wind data from different locations establishes that (in instances when this scaling exists the exponent α varies with location, owing to the influence of local environmental conditions on wind speed variability. Since manufacturer-calibrated power curves cannot account for variability influenced by local conditions, this variability translates to forecast uncertainty in power generation. We close with a proposal for operators to perform post-installation recalibration of their turbine power curves to account for the influence of local environmental factors on wind speed variability in order to reduce the uncertainty of wind power forecasts. Understanding the relationship between wind’s speed and its variability is likely to lead to lower costs for the integration of wind power into the electric grid.

Environmental aspects of large-scale wind-power systems in the UK

Science.gov (United States)

Robson, A.

1984-11-01

Environmental issues relating to the introduction of large, MW-scale wind turbines at land-based sites in the UK are discussed. Noise, television interference, hazards to bird life, and visual effects are considered. Areas of uncertainty are identified, but enough is known from experience elsewhere in the world to enable the first UK machines to be introduced in a safe and environementally acceptable manner. Research to establish siting criteria more clearly, and significantly increase the potential wind-energy resource is mentioned. Studies of the comparative risk of energy systems are shown to be overpessimistic for UK wind turbines.

Dynamic model of frequency control in Danish power system with large scale integration of wind power

DEFF Research Database (Denmark)

Basit, Abdul; Hansen, Anca Daniela; Sørensen, Poul Ejnar

2013-01-01

This work evaluates the impact of large scale integration of wind power in future power systems when 50% of load demand can be met from wind power. The focus is on active power balance control, where the main source of power imbalance is an inaccurate wind speed forecast. In this study, a Danish...... power system model with large scale of wind power is developed and a case study for an inaccurate wind power forecast is investigated. The goal of this work is to develop an adequate power system model that depicts relevant dynamic features of the power plants and compensates for load generation...... imbalances, caused by inaccurate wind speed forecast, by an appropriate control of the active power production from power plants....

International wind energy development. World market update 2011. Forecast 2012-2016

Energy Technology Data Exchange (ETDEWEB)

2012-03-15

The World Market Update 2011 is BTM Consult's seventeenth edition of this annual wind energy market report. The report includes more than 80 tables, charts and graphs illustrating global wind market development, as well as a wind market forecast for 2012 - 2016 and predictions for the wind market through 2021. The report delivers several views on the fast-growing wind market, including: 1) Record installation of 41.7 GW. 2) Strong presence of four Chinese wind turbine suppliers in the Top 10 list. 3) China maintains the No. 1 market position in the world, with 17.6 GW of new capacity. 4) Offshore wind is on track for increased contribution to wind power in Europe. 5) Market value will grow from Euro 52.2 billion in 2011 to Euro 86.3 billion in 2016. 6) Direct drive turbines now account for 21.2% of the world's supply of wind power capacity. 7) Wind power will deliver 2.26% of the world's electricity in 2012. 8) Forecasts and predictions to 2021 indicate that wind power can meet 8.0% of the world's consumption of electricity by 2021. International Wind Energy Development - World Update 2011 includes individual country wind market assessments, incentives around the world, and detailed analysis of both the demand and supply sides of the wind market in 2011. This year's report reviews the latest developments in hydraulic drivetrains, identifies the pros and cons, and compares the hydraulic technology to the industry's three currently established drivetrain technologies: conventional gear-, direct and hybrid-drivetrains. (Author)

Coherent structures at ion scales in fast and slow solar wind: Cluster observations

Science.gov (United States)

Perrone, D.; Alexandrova, O.; Zouganelis, Y.; Roberts, O.; Lion, S.; Escoubet, C. P.; Walsh, A. P.; Maksimovic, M.; Lacombe, C.

2017-12-01

Spacecraft measurements generally reveal that solar wind electromagnetic fluctuations are in a state of fully-developed turbulence. Turbulence represents a very complex problem in plasmas since cross-scale coupling and kinetic effects are present. Moreover, the intermittency phenomenon, i.e. the manifestation of the non-uniform and inhomogeneous energy transfer and dissipation in a turbulent system, represents a very important aspect of the solar wind turbulent cascade. Here, we study coherent structures responsible for solar wind intermittency around ion characteristic scales. We find that, in fast solar wind, intermittency is due to Alfvén vortex-like structures and current sheets. In slow solar wind, we observe as well compressive structures like magnetic solitons, holes and shocks. By using high-time resolution magnetic field data of multi-point measurements of Cluster spacecraft, we characterize the observed coherent structures in terms of topology and propagation speed. We show that all structures around ion characteristic scales, both in fast and slow solar wind, are characterized by a strong wave-vector anisotropy in the perpendicular direction with respect to the local magnetic field. Moreover, some of them propagate in the plasma rest frame in the direction perpendicular to the local field. Finally, a further analysis on the electron and ion velocity distributions shows a high variability; in particular, close to coherent structures the electron and ion distribution functions appear strongly deformed and far from the thermodynamic equilibrium. Possible interpretations of the observed structures and their role in the heating process of the plasma are also discussed.

Analysis of multi-scale chaotic characteristics of wind power based on Hilbert–Huang transform and Hurst analysis

International Nuclear Information System (INIS)

Liang, Zhengtang; Liang, Jun; Zhang, Li; Wang, Chengfu; Yun, Zhihao; Zhang, Xu

2015-01-01

Highlights: • A scale division method of wind power based on HHT and Hurst analysis is proposed. • The time–frequency components of wind power show different fractal structures. • These components are superposed and reconstructed into three scale subsequences. • Each subsequence has a chaotic characteristic and shows its own properties. • The EMD-LSSVM + ELM method improves the short-term wind power forecasting accuracy. - Abstract: The causes of uncertainty in wind farm power generation are not yet fully understood. A method for the scale division of wind power based on the Hilbert–Huang transform (HHT) and Hurst analysis is proposed in this paper, which allows the various multi-scale chaotic characteristics of wind power to be investigated to reveal further information about the dynamic behavior of wind power. First, the time–frequency characteristics of wind power are analyzed using the HHT, and then Hurst analysis is applied to analyze the stochastic/persistent characteristics of the different time–frequency components. Second, based on their fractal structures, the components are superposed and reconstructed into three series, which are defined as the Micro-, Meso- and Macro-scale subsequences. Finally, indices related to the statistical and behavioral characteristics of the subsequences are calculated and used to analyze their nonlinear dynamic behavior. The data collected from a wind farm of Hebei Province, China, are selected for case studies. The simulation results reveal that (1) although the time–frequency components can be decomposed, the different fractal structures of the signal are also derived from the original series; (2) the three scale subsequences all present chaotic characteristics and each of them exhibits its own unique properties. The Micro-scale subsequence shows strong randomness and contributes the least to the overall fluctuations; the Macro-scale subsequence is the steadiest and exhibits the most significant tendency

A probabilistic assessment of large scale wind power development for long-term energy resource planning

Science.gov (United States)

Kennedy, Scott Warren

A steady decline in the cost of wind turbines and increased experience in their successful operation have brought this technology to the forefront of viable alternatives for large-scale power generation. Methodologies for understanding the costs and benefits of large-scale wind power development, however, are currently limited. In this thesis, a new and widely applicable technique for estimating the social benefit of large-scale wind power production is presented. The social benefit is based upon wind power's energy and capacity services and the avoidance of environmental damages. The approach uses probabilistic modeling techniques to account for the stochastic interaction between wind power availability, electricity demand, and conventional generator dispatch. A method for including the spatial smoothing effect of geographically dispersed wind farms is also introduced. The model has been used to analyze potential offshore wind power development to the south of Long Island, NY. If natural gas combined cycle (NGCC) and integrated gasifier combined cycle (IGCC) are the alternative generation sources, wind power exhibits a negative social benefit due to its high capacity cost and the relatively low emissions of these advanced fossil-fuel technologies. Environmental benefits increase significantly if charges for CO2 emissions are included. Results also reveal a diminishing social benefit as wind power penetration increases. The dependence of wind power benefits on natural gas and coal prices is also discussed. In power systems with a high penetration of wind generated electricity, the intermittent availability of wind power may influence hourly spot prices. A price responsive electricity demand model is introduced that shows a small increase in wind power value when consumers react to hourly spot prices. The effectiveness of this mechanism depends heavily on estimates of the own- and cross-price elasticities of aggregate electricity demand. This work makes a valuable

Benchmarking of wind farm scale wake models in the EERA - DTOC project

DEFF Research Database (Denmark)

Réthoré, Pierre-Elouan; Hansen, Kurt Schaldemose; Barthelmie, R.J.

2013-01-01

-flow to combine wind farm (micro) and cluster (meso) scale wake models. For this purpose, a benchmark campaign is organized on the existing wind farm wake models available within the project, in order to identify which model would be the most appropriate for this coupling. A number of standardized wake cases......Designing offshore wind farms next to existing or planned wind farm clusters has recently become a common practice in the North Sea. These types of projects face unprecedented challenges in term of wind energy siting. The currently ongoing European project FP7 EERA - DTOC (Design Tool for Offshore...... wind farm Clusters) is aiming at providing a new type of model work-flow to address this issue. The wake modeling part of the EERA - DTOC project is to improve the fundamental understanding of wind turbine wakes and modeling. One of these challenges is to create a new kind of wake modeling work...

Simulating flow around scaled model of a hypersonic vehicle in wind tunnel

Science.gov (United States)

Markova, T. V.; Aksenov, A. A.; Zhluktov, S. V.; Savitsky, D. V.; Gavrilov, A. D.; Son, E. E.; Prokhorov, A. N.

2016-11-01

A prospective hypersonic HEXAFLY aircraft is considered in the given paper. In order to obtain the aerodynamic characteristics of a new construction design of the aircraft, experiments with a scaled model have been carried out in a wind tunnel under different conditions. The runs have been performed at different angles of attack with and without hydrogen combustion in the scaled propulsion engine. However, the measured physical quantities do not provide all the information about the flowfield. Numerical simulation can complete the experimental data as well as to reduce the number of wind tunnel experiments. Besides that, reliable CFD software can be used for calculations of the aerodynamic characteristics for any possible design of the full-scale aircraft under different operation conditions. The reliability of the numerical predictions must be confirmed in verification study of the software. The given work is aimed at numerical investigation of the flowfield around and inside the scaled model of the HEXAFLY-CIAM module under wind tunnel conditions. A cold run (without combustion) was selected for this study. The calculations are performed in the FlowVision CFD software. The flow characteristics are compared against the available experimental data. The carried out verification study confirms the capability of the FlowVision CFD software to calculate the flows discussed.

Havsnaes wind farm - The project financing of a Swedish wind farm

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

In March 2008 the ground breaking project financing of the 95 MW Havsnaes wind farm was completed. Havsnaes represents one of the cornerstones in portfolio of Venus Vind, controlled by HgCapital, where sustainable Scandinavian strength is build through industrial scale wind farms with local presence. At the time, Havsnaes represented the largest energy project financing in the market, it is also the first true project financing of a major Swedish wind farm. The aim of this study is to highlight the process of project financing and additional lessons learnt from the Havsnaes transaction. Investment in renewable energy projects often includes international investors. We welcome the growing Swedish wind market, banks and other financial institutions, politicians and other relevant decision makers to take part of our findings. Sponsorship provided by the Swedish Energy Agency has enabled the completion of this study.

Environmental aspects of large-scale wind-power systems in the UK

Energy Technology Data Exchange (ETDEWEB)

Robson, A

1983-12-01

Environmental issues relating to the introduction of large, MW-scale wind turbines at land-based sites in the U.K. are discussed. Areas of interest include noise, television interference, hazards to bird life and visual effects. A number of areas of uncertainty are identified, but enough is known from experience elsewhere in the world to enable the first U.K. machines to be introduced in a safe and environmentally acceptable manner. Research currently under way will serve to establish siting criteria more clearly, and could significantly increase the potential wind-energy resource. Certain studies of the comparative risk of energy systems are shown to be overpessimistic for U.K. wind turbines.

Experimental Study of a Small Scale Hydraulic System for Mechanical Wind Energy Conversion into Heat

Directory of Open Access Journals (Sweden)

Tadas Zdankus

2016-07-01

Full Text Available Significant potential for reducing thermal energy consumption in buildings of moderate and cold climate countries lies within wind energy utilisation. Unlike solar irradiation, character of wind speeds in Central and Northern Europe correspond to the actual thermal energy demand in buildings. However, mechanical wind energy undergoes transformation into electrical energy before being actually used as thermal energy in most wind energy applications. The study presented in this paper deals with hydraulic systems, designed for small-scale applications to eliminate the intermediate energy transformation as it converts mechanical wind energy into heat directly. The prototype unit containing a pump, flow control valve, oil tank and piping was developed and tested under laboratory conditions. Results of the experiments showed that the prototype system is highly efficient and adjustable to a broad wind velocity range by modifying the definite hydraulic system resistance. Development of such small-scale replicable units has the potential to promote “bottom-up” solutions for the transition to a zero carbon society.

Advanced multi-megawatt wind turbine design for utility application

Science.gov (United States)

Pijawka, W. C.

1984-08-01

A NASA/DOE program to develop a utility class multimegawatt wind turbine, the MOD-5A, is described. The MOD-5A features a 400 foot diameter rotor which is teetered and positioned upwind of the tower; a 7.3 megawatt power rating with a variable speed electric generating system; and a redundant rotor support and torque transmission structure. The rotor blades were fabricated from an epoxy-bonded wood laminate material which was a successful outgrowth of the MOD-OA airfoil design. Preliminary data from operational tests carried out at the NASA Plumbrook test facility are presented.

Advanced multi-megawatt wind turbine design for utility application

Science.gov (United States)

Pijawka, W. C.

1984-01-01

A NASA/DOE program to develop a utility class multimegawatt wind turbine, the MOD-5A, is described. The MOD-5A features a 400 foot diameter rotor which is teetered and positioned upwind of the tower; a 7.3 megawatt power rating with a variable speed electric generating system; and a redundant rotor support and torque transmission structure. The rotor blades were fabricated from an epoxy-bonded wood laminate material which was a successful outgrowth of the MOD-OA airfoil design. Preliminary data from operational tests carried out at the NASA Plumbrook test facility are presented.

A cross-cultural investigation into the dimensional structure and stability of the Barriers to Research and Utilization Scale (BARRIERS Scale).

Science.gov (United States)

Williams, Brett; Brown, Ted; Costello, Shane

2015-10-24

It is important that scales exhibit strong measurement properties including those related to the investigation of issues that impact evidence-based practice. The validity of the Barriers to Research Utilization Scale (BARRIERS Scale) has recently been questioned in a systematic review. This study investigated the dimensional structure and stability of the 28 item BARRIERS Scale when completed by three groups of participants from three different cross-cultural environments. Data from the BARRIERS Scale completed by 696 occupational therapists from Australia (n = 137), Taiwan (n = 413), and the United Kingdom (n = 144) were analysed using principal components analysis, followed by Procrustes Transformation. Poorly fitting items were identified by low communalities, cross-loading, and theoretically inconsistent primary loadings, and were systematically removed until good fit was achieved. The cross-cultural stability of the component structure of the BARRIERS Scale was examined. A four component, 19 item version of the BARRIERS Scale emerged that demonstrated an improved dimensional fit and stability across the three participant groups. The resulting four components were consistent with the BARRIERS Scale as originally conceptualised. Findings from the study suggest that the four component, 19 item version of the BARRIERS Scale is a robust and valid measure for identifying barriers to research utilization for occupational therapists in paediatric health care settings across Australia, United Kingdom, and Taiwan. The four component 19 item version of the BARRIERS Scale exhibited good dimensional structure, internal consistency, and stability.

Cost optimization of wind turbines for large-scale offshore wind farms

International Nuclear Information System (INIS)

Fuglsang, P.; Thomsen, K.

1998-02-01

This report contains a preliminary investigation of site specific design of off-shore wind turbines for a large off-shore wind farm project at Roedsand that is currently being proposed by ELKRAFT/SEAS. The results were found using a design tool for wind turbines that involve numerical optimization and aeroelastic calculations of response. The wind climate was modeled in detail and a cost function was used to estimate costs from manufacture and installation. Cost of energy is higher for off-shore installations. A comparison of an off-shore wind farm site with a typical stand alone on-shore site showed an increase of the annual production of 28% due to the difference in wind climate. Extreme loads and blade fatigue loads were nearly identical, however,fatigue loads on other main components increased significantly. Optimizations were carried out to find the optimum overall off-shore wind turbine design. A wind turbine for the off-shore wind farm should be different compared with a stand-alone on-shore wind turbine. The overall design changed were increased swept area and rated power combined with reduced rotor speed and tower height. Cost was reduced by 12% for the final 5D/14D off-shore wind turbine from 0.306 DKr/kWh to 0.270 DKr/kWh. These figures include capital costs from manufacture and installation but not on-going costs from maintenance. These results make off-shore wind farms more competitive and comparable to the reference on-shore stand-alone wind turbine. A corresponding reduction of cost of energy could not be found for the stand alone on-shore wind turbine. Furthermore the fatigue loads on wind turbines in on-shore wind farms will increase and cost of energy will increase in favor of off-shore wind farms. (au) EFP-95; EU-JOULE-3; 21 tabs., 7 ills., 8 refs

Toward efficient optimization of wind farm layouts: Utilizing exact gradient information

International Nuclear Information System (INIS)

Guirguis, David; Romero, David A.; Amon, Cristina H.

2016-01-01

Highlights: • A mathematical programming approach is proposed to solve the WFLO problem. • Differentiable mathematical models are developed to handle land-use constraints. • Test cases with significant land-use constraints are solved efficiently. • The proposed approach outperforms genetic algorithm. - Abstract: The Wind Farm Layout Optimization (WFLO) problem has attracted a lot of attention from researchers and industry practitioners, as it has been proven that better placement of wind turbines can increase the overall efficiency and the total revenue of a wind farm. Although the engineering wake models are commonly used for layout optimization, the literature seems to have settled on using metaheuristics and stochastic optimization methods. In the present study, we show the effectiveness of non-linear mathematical programming in solving continuous-variable WFLO problems by utilizing exact gradient information of the problem’s objective and constraints. Moreover, mathematical models for handling land-use constraints are developed to solve highly constrained practical problems. For demonstration purposes, the results were compared with those obtained by a genetic algorithm, using a set of test cases that have been frequently used in the WFLO literature. Additional test cases with higher dimensionality, significant land-availability constraints and higher wind farm turbine densities (i.e., turbines per square kilometer) are devised and solved to show the merits of the proposed approach. Our results show the superiority of mathematical programing in solving this problem, as evidenced by the resulting wind farm efficiency and the computational cost required to obtain the solutions.

2014 Wind Technologies Market Report

Energy Technology Data Exchange (ETDEWEB)

Wiser, R; Bolinger, M.

2015-08-01

According to the 2014 Wind Technologies Market Report, total installed wind power capacity in the United States grew at a rate of eight percent in 2014, bringing the United States total installed capacity to nearly 66 gigawatts (GW), which ranks second in the world and meets 4.9 percent of U.S. end-use electricity demand in an average year. In total, 4,854 MW of new wind energy capacity were installed in the United States in 2014. The 2014 Wind Technologies Market Report also finds that wind energy prices are at an all-time low and are competitive with wholesale power prices and traditional power sources across many areas of the United States. Additionally, a new trend identified by the 2014 Wind Technologies Market Report shows utility-scale turbines with larger rotors designed for lower wind speeds have been increasingly deployed across the country in 2014. The findings also suggest that the success of the U.S. wind industry has had a ripple effect on the American economy, supporting 73,000 jobs related to development, siting, manufacturing, transportation, and other industries.

Megawatt wind turbines gaining momentum

International Nuclear Information System (INIS)

Oehlenschlaeger, K.; Madsen, B.T.

1996-01-01

Through the short history of the modern wind turbine, electric utilities have made it amply clear that they have held a preference for large scale wind turbines over smaller ones, which is why wind turbine builders through the years have made numerous attempts develop such machines - machines that would meet the technical, aesthetic and economic demands that a customer would require. Considerable effort was put into developing such wind turbines in the early 1980s. There was the U.S. Department of Energy's MOD 1-5 program, which ranged up to 3.2 MW, Denmark's Nibe A and B, 630 kW turbine and the 2 MW Tjaereborg machine, Sweden's Naesudden, 3 MW, and Germany's Growian, 3 MW. Most of these were dismal failures, though some did show the potential of MW technology. (au)

MPC for Wind Power Gradients - Utilizing Forecasts, Rotor Inertia, and Central Energy Storage

DEFF Research Database (Denmark)

Hovgaard, Tobias Gybel; Larsen, Lars F. S.; Jørgensen, John Bagterp

2013-01-01

decentralized energy storage in the turbines’ inertia combined with a central storage unit or deferrable consumers can be utilized to achieve this goal at a minimum cost. We propose a variation on model predictive control to incorporate predictions of wind speed. Due to the aerodynamics of the turbines...

Comparison of wind pressure measurements on Silsoe ...

African Journals Online (AJOL)

International Journal of Engineering, Science and Technology ... from full-scale observation, wind-tunnel experiments and various CFD techniques ... The paper is the result of extensive research concentrated on analyzing the accuracy and ...

International energy technology collaboration: wind power integration into electricity systems

International Nuclear Information System (INIS)

Justus, D.

2006-01-01

A rapid growth of wind power since the 1990s has led to notable market shares in some electricity markets. This growth is concentrated in a few countries with effective Research, Development and Demonstration (RD and D) programmes and with policies that support its diffusion into the market place. The speed and depth of its penetration in these electricity markets have amplified the need to address grid integration concerns, so as not to impede the further penetration of wind power. Research on technologies, tools and practices for integrating large amounts of wind power into electricity supply systems is attempting to respond to this need. In recent years, existing international collaborative research efforts have expanded their focus to include grid integration of wind power and new consortia have been formed to pool knowledge and resources. Effective results benefit a few countries that already have a significant amount of wind in their electricity supply fuel mix, as well as to the potential large markets worldwide. This paper focuses on the challenge of bringing significant amounts of intermittent generating sources into grids dominated by large central generating units. It provides a brief overview of the growth of wind power, mainly since 1990, the technical and operational issues related to integration and selected collaborative programmes underway to address grid integration concerns. (author)

Analysis of a utility-interactive wind-photovoltaic hybrid system with battery storage using neural network

Science.gov (United States)

Giraud, Francois

1999-10-01

This dissertation investigates the application of neural network theory to the analysis of a 4-kW Utility-interactive Wind-Photovoltaic System (WPS) with battery storage. The hybrid system comprises a 2.5-kW photovoltaic generator and a 1.5-kW wind turbine. The wind power generator produces power at variable speed and variable frequency (VSVF). The wind energy is converted into dc power by a controlled, tree-phase, full-wave, bridge rectifier. The PV power is maximized by a Maximum Power Point Tracker (MPPT), a dc-to-dc chopper, switching at a frequency of 45 kHz. The whole dc power of both subsystems is stored in the battery bank or conditioned by a single-phase self-commutated inverter to be sold to the utility at a predetermined amount. First, the PV is modeled using Artificial Neural Network (ANN). To reduce model uncertainty, the open-circuit voltage VOC and the short-circuit current ISC of the PV are chosen as model input variables of the ANN. These input variables have the advantage of incorporating the effects of the quantifiable and non-quantifiable environmental variants affecting the PV power. Then, a simplified way to predict accurately the dynamic responses of the grid-linked WPS to gusty winds using a Recurrent Neural Network (RNN) is investigated. The RNN is a single-output feedforward backpropagation network with external feedback, which allows past responses to be fed back to the network input. In the third step, a Radial Basis Functions (RBF) Network is used to analyze the effects of clouds on the Utility-Interactive WPS. Using the irradiance as input signal, the network models the effects of random cloud movement on the output current, the output voltage, the output power of the PV system, as well as the electrical output variables of the grid-linked inverter. Fourthly, using RNN, the combined effects of a random cloud and a wind gusts on the system are analyzed. For short period intervals, the wind speed and the solar radiation are considered as

Stereo particle image velocimetry set up for measurements in the wake of scaled wind turbines

Science.gov (United States)

Campanardi, Gabriele; Grassi, Donato; Zanotti, Alex; Nanos, Emmanouil M.; Campagnolo, Filippo; Croce, Alessandro; Bottasso, Carlo L.

2017-08-01

Stereo particle image velocimetry measurements were carried out in the boundary layer test section of Politecnico di Milano large wind tunnel to survey the wake of a scaled wind turbine model designed and developed by Technische Universität München. The stereo PIV instrumentation was set up to survey the three velocity components on cross-flow planes at different longitudinal locations. The area of investigation covered the entire extent of the wind turbines wake that was scanned by the use of two separate traversing systems for both the laser and the cameras. Such instrumentation set up enabled to gain rapidly high quality results suitable to characterise the behaviour of the flow field in the wake of the scaled wind turbine. This would be very useful for the evaluation of the performance of wind farm control methodologies based on wake redirection and for the validation of CFD tools.

WindPACT Turbine Design Scaling Studies Technical Area 1-Composite Blades for 80- to 120-Meter Rotor

Energy Technology Data Exchange (ETDEWEB)

Griffin, D.A.

2001-04-30

The United States Department of Energy (DOE) through the National Renewable Energy Laboratory (NREL) implemented the Wind Partnership for Advanced Component Technologies (WindPACT) program. As part of the WindPACT program, Global Energy Concepts, LLC (GEC), was awarded contract number YAM-0-30203-01 to examine Technical Area 1-Blade Scaling, Technical Area 2-Turbine Rotor and Blade Logistics, and Technical Area 3-Self-Erecting Towers. This report documents the results of GEC's Technical Area 1-Blade Scaling. The primary objectives of the Blade-Scaling Study are to assess the scaling of current materials and manufacturing technologies for blades of 40 to 60 meters in length, and to develop scaling curves of estimated cost and mass for rotor blades in that size range.

Wind Energy Resource Atlas of Mongolia

Energy Technology Data Exchange (ETDEWEB)

Elliott, D; Schwartz, M; Scott, G.; Haymes, S.; Heimiller, D.; George, R.

2001-08-27

The United States Department of Energy (DOE) and the United States Agency for International Development (USAID) sponsored a project to help accelerate the large-scale use of wind energy technologies in Mongolia through the development of a wind energy resource atlas of Mongolia. DOE's National Renewable Energy Laboratory (NREL) administered and conducted this project in collaboration with USAID and Mongolia. The Mongolian organizations participating in this project were the Scientific, Production, and Trade Corporation for Renewable Energy (REC) and the Institute of Meteorology and Hydrology (IMH). The primary goals of the project were to develop detailed wind resource maps for all regions of Mongolia for a comprehensive wind resource atlas, and to establish a wind-monitoring program to identify prospective sites for wind energy projects and help validate some of the wind resource estimates.

A hybrid wavelet transform based short-term wind speed forecasting approach.

Science.gov (United States)

Wang, Jujie

2014-01-01

It is important to improve the accuracy of wind speed forecasting for wind parks management and wind power utilization. In this paper, a novel hybrid approach known as WTT-TNN is proposed for wind speed forecasting. In the first step of the approach, a wavelet transform technique (WTT) is used to decompose wind speed into an approximate scale and several detailed scales. In the second step, a two-hidden-layer neural network (TNN) is used to predict both approximated scale and detailed scales, respectively. In order to find the optimal network architecture, the partial autocorrelation function is adopted to determine the number of neurons in the input layer, and an experimental simulation is made to determine the number of neurons within each hidden layer in the modeling process of TNN. Afterwards, the final prediction value can be obtained by the sum of these prediction results. In this study, a WTT is employed to extract these different patterns of the wind speed and make it easier for forecasting. To evaluate the performance of the proposed approach, it is applied to forecast Hexi Corridor of China's wind speed. Simulation results in four different cases show that the proposed method increases wind speed forecasting accuracy.

Results of flutter test OS6 obtained using the 0.14-scale wing/elevon model (54-0) in the NASA LaRC 16-foot transonic dynamics wind tunnel

Science.gov (United States)

Berthold, C. L.

1977-01-01

A 0.14-scale dynamically scaled model of the space shuttle orbiter wing was tested in the Langley Research Center 16-Foot Transonic Dynamics Wind Tunnel to determine flutter, buffet, and elevon buzz boundaries. Mach numbers between 0.3 and 1.1 were investigated. Rockwell shuttle model 54-0 was utilized for this investigation. A description of the test procedure, hardware, and results of this test is presented.

A study of rotor and platform design trade-offs for large-scale floating vertical axis wind turbines

Science.gov (United States)

Griffith, D. Todd; Paquette, Joshua; Barone, Matthew; Goupee, Andrew J.; Fowler, Matthew J.; Bull, Diana; Owens, Brian

2016-09-01

Vertical axis wind turbines are receiving significant attention for offshore siting. In general, offshore wind offers proximity to large populations centers, a vast & more consistent wind resource, and a scale-up opportunity, to name a few beneficial characteristics. On the other hand, offshore wind suffers from high levelized cost of energy (LCOE) and in particular high balance of system (BoS) costs owing to accessibility challenges and limited project experience. To address these challenges associated with offshore wind, Sandia National Laboratories is researching large-scale (MW class) offshore floating vertical axis wind turbines (VAWTs). The motivation for this work is that floating VAWTs are a potential transformative technology solution to reduce offshore wind LCOE in deep-water locations. This paper explores performance and cost trade-offs within the design space for floating VAWTs between the configurations for the rotor and platform.

FOREWORD: 6th International Conference on Pumps and Fans with Compressors and Wind Turbines (ICPF2013)

Science.gov (United States)

Wu, Yulin; Wang, Zhengwei; Yuan, Shouqi; Shi, Weidong; Liu, Shuhong; Luo, Xingqi; Wang, Fujun

2013-12-01

The 6th International Conference on Pumps and Fans with Compressors and Wind Turbines (ICPF 2013) was held in Beijing, China, 19-22 September 2013, which was jointly organized by Tsinghua University and Jiangsu University. The co-organizers were Zhejiang University, Zhejiang Sci-Tech University, The State Key Laboratory of Hydroscience and Engineering, The State Key Laboratory of Automotive Safety and Energy and Beijing International Science and Technology Cooperation Base for CO2 Utilization and Reduction. The sponsor of the conference was Concepts NREC. The First International Conference on Pumps and Systems (May 1992), the Second International Conference on Pumps and Fans (October 1995), the Third International Conference on Pumps and Fans (October 1998), and the Fourth International Conference on Pumps and Fans (26-29 August 2002) were all held in Beijing and were organized by the late famous Chinese professor on fluid machinery and engineering, Professor Zuyan Mei of Tsinghua University. The conference was interrupted by the death of Professor Mei in 2003. In order to commemorate Professor Mei, the organizing committee of ICPF decided to continue organizing the conference series. The Fifth Conference on Pumps and Systems (2010 ICPF) took place in Hangzhou, Zhejiang Province, China, 18-21 October 2010, and it was jointly organized by Zhejiang University and Tsinghua University. With the development of renewable energy and new energy in China and in the world, some small types of compressor and some types of pump, as well as wind turbines are developing very fast; therefore the ICPF2013 conference included compressors and wind turbines. The theme of the conference was the application of renewable energy of pumps, compressors, fans and blowers. The content of the conference was the basic study, design and experimental study of compressors, fans, blowers and pumps; the CFD application on pumps and fans, their transient behavior, unsteady flows and multi-phase flow

Round-the-year security analysis with large-scale wind power integration

NARCIS (Netherlands)

Ciupuliga, A.R.; Gibescu, M.; Pelgrum, E.; Jacobs, P.G.H.; Jansen, K.P.G.; Kling, W.L.

2012-01-01

The ongoing liberalization process together with the growing penetration of renewable energy sources (RES), e.g., wind power, require an internationally oriented transmission planning approach that considers the increased uncertainties in terms of trade, location of generation, and output of

Endurance Wind Power : practical insights into small wind

International Nuclear Information System (INIS)

Hicks, D.

2008-01-01

This presentation discussed practical issues related to purchasing and installing small wind turbines in Canada. Wind power capacity can be estimated by looking at provincial wind maps as well as by seeking wind data at local airports. Wind resources are typically measured at heights of between 20 meters and 50 m. The height of a wind turbine tower can significantly increase the turbine's wind generating capacity. Turbine rotors should always be placed 30 feet higher than obstacles within 500 feet. Many provinces have now mandated utilities to accept renewable energy resources from grid-connected wind energy plants. Net billing systems are used to determine the billing relationship between power-producing consumers and the utilities who will buy the excess power and sell it to other consumers. Utilities are not yet mandated to purchase excess power, and it is likely that federal and provincial legislation will be needed to ensure that net billing systems continue to grow. Many Canadian municipalities have no ordinances related to wind turbine placements. Consumers interested in purchasing small wind turbines should ensure that the turbine has been certified by an accredited test facility and has an adequate safety system. The noise of the turbine as well as its power performance in relation to the purchaser's needs must also be considered. It was concluded that small wind turbines can provide a means for electricity consumers to reduce their carbon footprint and hedge against the inflationary costs of fossil-fuelled energy resources. tabs., figs

Progresses in application of computational ?uid dynamic methods to large scale wind turbine aerodynamics?

Institute of Scientific and Technical Information of China (English)

Zhenyu ZHANG; Ning ZHAO; Wei ZHONG; Long WANG; Bofeng XU

2016-01-01

The computational ?uid dynamics (CFD) methods are applied to aerody-namic problems for large scale wind turbines. The progresses including the aerodynamic analyses of wind turbine pro?les, numerical ?ow simulation of wind turbine blades, evalu-ation of aerodynamic performance, and multi-objective blade optimization are discussed. Based on the CFD methods, signi?cant improvements are obtained to predict two/three-dimensional aerodynamic characteristics of wind turbine airfoils and blades, and the vorti-cal structure in their wake ?ows is accurately captured. Combining with a multi-objective genetic algorithm, a 1.5 MW NH-1500 optimized blade is designed with high e?ciency in wind energy conversion.

Power control and management of the grid containing largescale wind power systems

Science.gov (United States)

Aula, Fadhil Toufick

The ever increasing demand for electricity has driven many countries toward the installation of new generation facilities. However, concerns such as environmental pollution and global warming issues, clean energy sources, high costs associated with installation of new conventional power plants, and fossil fuels depletion have created many interests in finding alternatives to conventional fossil fuels for generating electricity. Wind energy is one of the most rapidly growing renewable power sources and wind power generations have been increasingly demanded as an alternative to the conventional fossil fuels. However, wind power fluctuates due to variation of wind speed. Therefore, large-scale integration of wind energy conversion systems is a threat to the stability and reliability of utility grids containing these systems. They disturb the balance between power generation and consumption, affect the quality of the electricity, and complicate load sharing and load distribution managing and planning. Overall, wind power systems do not help in providing any services such as operating and regulating reserves to the power grid. In order to resolve these issues, research has been conducted in utilizing weather forecasting data to improve the performance of the wind power system, reduce the influence of the fluctuations, and plan power management of the grid containing large-scale wind power systems which consist of doubly-fed induction generator based energy conversion system. The aims of this research, my dissertation, are to provide new methods for: smoothing the output power of the wind power systems and reducing the influence of their fluctuations, power managing and planning of a grid containing these systems and other conventional power plants, and providing a new structure of implementing of latest microprocessor technology for controlling and managing the operation of the wind power system. In this research, in order to reduce and smooth the fluctuations, two

2012 Market Report on Wind Technologies in Distributed Applications

Energy Technology Data Exchange (ETDEWEB)

Orrell, Alice C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2013-08-01

An annual report on U.S. wind power in distributed applications – expanded to include small, mid-size, and utility-scale installations – including key statistics, economic data, installation, capacity, and generation statistics, and more.

Roadmap of retail electricity market reform in China: assisting in mitigating wind energy curtailment

Science.gov (United States)

Yu, Dezhao; Qiu, Huadong; Yuan, Xiang; Li, Yuan; Shao, Changzheng; Lin, You; Ding, Yi

2017-01-01

Among the renewable energies, wind energy has gained the rapidest development in China. Moreover wind power generation has been penetrated into power system in a large scale. However, the high level wind curtailment also indicates a low efficiency of wind energy utilization over the last decade in China. One of the primary constraints on the utilization of wind energy is the lack of an electricity market, in which renewable energies can compete equally with traditional fossil fuel generation. Thus the new round electric power industry reform is essential in China. The reform involves implementing new pricing mechanism, introducing retail-side competition, promoting the consumption of renewable energy. The new round reform can be a promising solution for promoting the development and consumption of wind energy generation in China. Based on proposed reform policies of electric power industry, this paper suggests a roadmap for retail electricity market reform of China, which consists of three stages. Barriers to the efficient utilization of wind energy are also analysed. Finally, this paper introduces several efficient measures for mitigating wind curtailment in each stage of reform.

Two methods for estimating limits to large-scale wind power generation.

Science.gov (United States)

Miller, Lee M; Brunsell, Nathaniel A; Mechem, David B; Gans, Fabian; Monaghan, Andrew J; Vautard, Robert; Keith, David W; Kleidon, Axel

2015-09-08

Wind turbines remove kinetic energy from the atmospheric flow, which reduces wind speeds and limits generation rates of large wind farms. These interactions can be approximated using a vertical kinetic energy (VKE) flux method, which predicts that the maximum power generation potential is 26% of the instantaneous downward transport of kinetic energy using the preturbine climatology. We compare the energy flux method to the Weather Research and Forecasting (WRF) regional atmospheric model equipped with a wind turbine parameterization over a 10(5) km2 region in the central United States. The WRF simulations yield a maximum generation of 1.1 We⋅m(-2), whereas the VKE method predicts the time series while underestimating the maximum generation rate by about 50%. Because VKE derives the generation limit from the preturbine climatology, potential changes in the vertical kinetic energy flux from the free atmosphere are not considered. Such changes are important at night when WRF estimates are about twice the VKE value because wind turbines interact with the decoupled nocturnal low-level jet in this region. Daytime estimates agree better to 20% because the wind turbines induce comparatively small changes to the downward kinetic energy flux. This combination of downward transport limits and wind speed reductions explains why large-scale wind power generation in windy regions is limited to about 1 We⋅m(-2), with VKE capturing this combination in a comparatively simple way.

Wind farm projects as joint ventures between a Danish utility and private cooperatives

International Nuclear Information System (INIS)

Moerup-Petersen, V.; Pedersen, S.

1992-01-01

Four cases on successful cooperation between the Danish utility, NESA A/S, and private wind cooperatives are described. In two cases the utility was invited to share the projects prepared by the cooperatives. In the third case the project was developed by the utility. The fourth and most ambitious project, where construction work is just about to start, both parties are involved on a 50/50 basis. The experience gained from the different projects is described. The paper discusses the advantages and disadvantages of joint projects for both parties. Different models on cooperation are outlined. Mainly based on NESA's experience, the joint concept is recommended by the Danish Ministry of Environment. The aim is to get the optimal utilization of the limited siting possibilities in Denmark. The future perspectives of joint projects are anticipated. (au)

Design study of coated conductor direct drive wind turbine generator for small scale demonstration

DEFF Research Database (Denmark)

Abrahamsen, Asger Bech; Jensen, Bogi Bech

2012-01-01

We have investigated the properties of a superconducting direct drive generator suitable for demonstration in a small scale 11 kW wind turbine. The engineering current density of the superconducting field windings is based on properties of coated conductors wound into coils holding of the order 68...

Performance of automatic generation control mechanisms with large-scale wind power

Energy Technology Data Exchange (ETDEWEB)

Ummels, B.C.; Gibescu, M.; Paap, G.C. [Delft Univ. of Technology (Netherlands); Kling, W.L. [Transmission Operations Department of TenneT bv (Netherlands)

2007-11-15

The unpredictability and variability of wind power increasingly challenges real-time balancing of supply and demand in electric power systems. In liberalised markets, balancing is a responsibility jointly held by the TSO (real-time power balancing) and PRPs (energy programs). In this paper, a procedure is developed for the simulation of power system balancing and the assessment of AGC performance in the presence of large-scale wind power, using the Dutch control zone as a case study. The simulation results show that the performance of existing AGC-mechanisms is adequate for keeping ACE within acceptable bounds. At higher wind power penetrations, however, the capabilities of the generation mix are increasingly challenged and additional reserves are required at the same level. (au)

Origin of the two scales of wind ripples on Mars

Science.gov (United States)

Lapotre, M. G. A.; Ewing, R. C.; Lamb, M. P.; Fischer, W. W.; Grotzinger, J. P.; Rubin, D. M.; Lewis, K. W.; Ballard, M.; Day, M. D.; Gupta, S.; Banham, S.; Bridges, N.; Des Marais, D. J.; Fraeman, A. A.; Grant, J. A., III; Ming, D. W.; Mischna, M.; Rice, M. S.; Sumner, D. Y.; Vasavada, A. R.; Yingst, R. A.

2016-12-01

Earth's sandy deserts host two main types of bedforms - decimeter-scale ripples and larger dunes. Years of orbital observations on Mars also confirmed the existence of two modes of active eolian bedforms - meter-scale ripples, and dunes. By analogy to terrestrial ripples, which are thought to form from a grain mechanism, it was hypothesized that large martian ripples also formed from grain impacts, but spaced further apart due to elongated saltation trajectories from the lower martian gravity and different atmospheric properties. However, the Curiosity rover recently documented the coexistence of three scales of bedforms in Gale crater. Because a grain impact mechanism cannot readily explain two distinct and coeval ripple modes in similar sand sizes, a new mechanism seems to be required to explain one of the scales of ripples. Small ripples are most similar to Earth's impact ripples, with straight crests and subdued profiles. In contrast, large martian ripples are sinuous and asymmetric, with lee slopes dominated by grain flows and grainfall deposits. Thus, large martian ripples resemble current ripples formed underwater on Earth, suggesting that they may form from a fluid-drag mechanism. To test this hypothesis, we develop a scaling relation to predict the spacing of fluid-drag ripples from an extensive flume data compilation. The size of large martian ripples is predicted by our scaling relation when adjusted for martian atmospheric properties. Specifically, we propose that the wavelength of martian wind-drag ripples arises from the high kinematic viscosity of the low-density atmosphere. Because fluid density controls drag-ripple size, our scaling relation can help constrain paleoatmospheric density from wind-drag ripple stratification.

Scale Adaptive Simulation Model for the Darrieus Wind Turbine

Science.gov (United States)

Rogowski, K.; Hansen, M. O. L.; Maroński, R.; Lichota, P.

2016-09-01

Accurate prediction of aerodynamic loads for the Darrieus wind turbine using more or less complex aerodynamic models is still a challenge. One of the problems is the small amount of experimental data available to validate the numerical codes. The major objective of the present study is to examine the scale adaptive simulation (SAS) approach for performance analysis of a one-bladed Darrieus wind turbine working at a tip speed ratio of 5 and at a blade Reynolds number of 40 000. The three-dimensional incompressible unsteady Navier-Stokes equations are used. Numerical results of aerodynamic loads and wake velocity profiles behind the rotor are compared with experimental data taken from literature. The level of agreement between CFD and experimental results is reasonable.

77 FR 485 - Wind Plant Performance-Public Meeting on Modeling and Testing Needs for Complex Air Flow...

Science.gov (United States)

2012-01-05

... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy Wind Plant Performance... and on-shore utility-scale wind power plants. DOE is requesting this information to support the development of cost-effective wind power deployment. DATES: The meeting will be held Tuesday, January 17, 2012...

Full-Scale Field Test of a Blade-Integrated Dual-Telescope Wind Lidar

DEFF Research Database (Denmark)

Pedersen, Anders Tegtmeier; Sjöholm, Mikael; Angelou, Nikolas

. Simultaneously, data regarding wind speed, rotational speed, and pitch angle recorded by the turbine was logged as well as data from a nearby met mast. The encouraging results of this first campaign include wind speed measurements at 20 Hz data rate along the rotor plane, acquired during the co...... in the top and bottom of the rotor plane. Conclusion We present here what we believe is the first successful wind speed measurements from a dual-telescope lidar installed on the blade of an operating wind turbine. The full-scale field test performed in the summer of 2012 has clearly demonstrated...... the possibility of integrating lidar telescopes into turbine blades as well as the capability of the lidar to measure the required wind speeds and to operate in the challenging environment of a rotating spinner and vibrating blade. The use of two separate telescopes allows a direct measurement of the blade’s AOA...

Neuron-Adaptive PID Based Speed Control of SCSG Wind Turbine System

Directory of Open Access Journals (Sweden)

Shan Zuo

2014-01-01

Full Text Available In searching for methods to increase the power capacity of wind power generation system, superconducting synchronous generator (SCSG has appeared to be an attractive candidate to develop large-scale wind turbine due to its high energy density and unprecedented advantages in weight and size. In this paper, a high-temperature superconducting technology based large-scale wind turbine is considered and its physical structure and characteristics are analyzed. A simple yet effective single neuron-adaptive PID control scheme with Delta learning mechanism is proposed for the speed control of SCSG based wind power system, in which the RBF neural network (NN is employed to estimate the uncertain but continuous functions. Compared with the conventional PID control method, the simulation results of the proposed approach show a better performance in tracking the wind speed and maintaining a stable tip-speed ratio, therefore, achieving the maximum wind energy utilization.

On the Wind Energy Resource and Its Trend in the East China Sea

Directory of Open Access Journals (Sweden)

Adekunle Ayodotun Osinowo

2017-01-01

Full Text Available This study utilizes a 30-year (1980–2009 10 m wind field dataset obtained from the European Center for Medium Range Weather Forecast to investigate the wind energy potential in the East China Sea (ECS by using Weibull shape and scale parameters. The region generally showed good wind characteristics. The calculated annual mean of the wind power resource revealed the potential of the region for large-scale grid-connected wind turbine applications. Furthermore, the spatiotemporal variations showed strong trends in wind power in regions surrounding Taiwan Island. These regions were evaluated with high wind potential and were rated as excellent locations for installation of large wind turbines for electrical energy generation. Nonsignificant and negative trends dominated the ECS and the rest of the regions; therefore, these locations were found to be suitable for small wind applications. The wind power density exhibited an insignificant trend in the ECS throughout the study period. The trend was strongest during spring and weakest during autumn.

Wind turbine aerodynamics

Energy Technology Data Exchange (ETDEWEB)

Johnson, D.A. [Waterloo Univ., ON (Canada). Dept. of Mechanical Engineering, Wind Energy Group

2010-07-01

The need for clean, renewable electricity in remote communities of Canada and the world was discussed in this presentation. The University of Waterloo Wind Energy Laboratory (WEL) performs research in a large scale indoor environment on wind turbines, blade aerodynamics, and aeroacoustics. A key area of research involves developing turbines for remote off-grid communities where climatic conditions are challenging. This presentation outlined research that is underway on wind energy and off-grid renewable energy systems. Many communities in Canada and remote communities in the rest of the world are not connected to the grid and are dependent on other means to supply electrical energy to their community. Remote communities in northern Canada have no road access and diesel is the dominant source of electrical energy for these communities. All of the community supply of diesel comes from brief winter road access or by air. The presentation discussed existing diesel systems and the solution of developing local renewable energy sources such as wind, hydro, biomass, geothermal, and solar power. Research goals, wind energy activities, experimental equipment, and the results were also presented. Research projects have been developed in wind energy; hydrogen generation/storage/utilization; power electronics/microgrid; and community engagement. figs.

International wind energy development. World market update 1996. Forecast 1997-2001

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

It is intended topublish and update this report `International Wind Power Development - Market Update 1996` every year in March. The latest issue was published in December of 1995 by BTM Consult ApS. Market data for demand side does normally, where it has been possible, only include installed wind turbines which has been connected to the grid during 1996. Supply side data is based on collected information (reference lists) from the 12-15 largest wind turbine manufacturers in the world. Due to these circumstances there are some conflicts between demand side and supply side data. Another important factor is that all wind turbine manufacturers do not use the same methodology when they are making their reference lists. Some manufacturers include only installed and operating wind turbines, while others include all units shipped from the factory. This is another conflict that might cause some differences in the data. Lately another new issue has been added to the list of uncertain factors, which is: is a Nordex Balcke-Duerr wind turbine Danish or German? And is a Gamesa Eolica wind turbine Danish or Spanish? etc. To minimize annual variations, this report includes the last 3 years data for the largest markets and wind turbine manufacturers. The prognosis includes data for the next 5 years until the year 2001, and an estimate has also been included for development until the year 2005. This version of the report can be found on internet web-pages: http://home4.inet.tele.dk/btmcwind/index.html. (EG)

International wind energy development. World market update 1996. Forecast 1997-2001

International Nuclear Information System (INIS)

1997-03-01

It is intended topublish and update this report 'International Wind Power Development - Market Update 1996' every year in March. The latest issue was published in December of 1995 by BTM Consult ApS. Market data for demand side does normally, where it has been possible, only include installed wind turbines which has been connected to the grid during 1996. Supply side data is based on collected information (reference lists) from the 12-15 largest wind turbine manufacturers in the world. Due to these circumstances there are some conflicts between demand side and supply side data. Another important factor is that all wind turbine manufacturers do not use the same methodology when they are making their reference lists. Some manufacturers include only installed and operating wind turbines, while others include all units shipped from the factory. This is another conflict that might cause some differences in the data. Lately another new issue has been added to the list of uncertain factors, which is: is a Nordex Balcke-Duerr wind turbine Danish or German? And is a Gamesa Eolica wind turbine Danish or Spanish? etc. To minimize annual variations, this report includes the last 3 years data for the largest markets and wind turbine manufacturers. The prognosis includes data for the next 5 years until the year 2001, and an estimate has also been included for development until the year 2005. This version of the report can be found on internet web-pages: http://home4.inet.tele.dk/btmcwind/index.html. (EG)

Thermospheric winds in the auroral oval: observations of small scale structures and rapid fluctuations by a Doppler imaging system

International Nuclear Information System (INIS)

Batten, S.; Rees, D.

1990-01-01

At high geomagnetic latitudes, thermospheric wind flows are dramatically affected by the combined effects of magnetospheric ion convection and Joule and particle heating. Thermospheric winds have been observed by ground based and space-borne Fabry-Perot interferometers (FPIs). Short period, localized wind fluctuations have always been difficult to resolve with a conventional FPI, due to the limited time and spatial resolution. However, the highest quality wind data obtained by these instruments from the middle and upper thermosphere have implied that thermospheric winds may respond to the combination of strong local ion drag forcing and heating within the auroral oval and polar cap, with spatial scale sizes of 50-500 km, and with time scales as short as 10-30 min. Since the 1982/1983 winter, a prototype Doppler Imaging System (DIS) has been operated at Kiruna (67.84 0 N, 20.42 0 E). This instrument maps thermospheric wind flows over a region some 500 km in diameter centred on Kiruna and has observed many interesting features in the thermospheric wind fields. In particular, strong local wind gradients, rapid wind reversals and small scale structures are regularly observed, particularly during geomagnetically disturbed nights. (author)

Variability of interconnected wind plants: correlation length and its dependence on variability time scale

Science.gov (United States)

St. Martin, Clara M.; Lundquist, Julie K.; Handschy, Mark A.

2015-04-01

The variability in wind-generated electricity complicates the integration of this electricity into the electrical grid. This challenge steepens as the percentage of renewably-generated electricity on the grid grows, but variability can be reduced by exploiting geographic diversity: correlations between wind farms decrease as the separation between wind farms increases. But how far is far enough to reduce variability? Grid management requires balancing production on various timescales, and so consideration of correlations reflective of those timescales can guide the appropriate spatial scales of geographic diversity grid integration. To answer ‘how far is far enough,’ we investigate the universal behavior of geographic diversity by exploring wind-speed correlations using three extensive datasets spanning continents, durations and time resolution. First, one year of five-minute wind power generation data from 29 wind farms span 1270 km across Southeastern Australia (Australian Energy Market Operator). Second, 45 years of hourly 10 m wind-speeds from 117 stations span 5000 km across Canada (National Climate Data Archive of Environment Canada). Finally, four years of five-minute wind-speeds from 14 meteorological towers span 350 km of the Northwestern US (Bonneville Power Administration). After removing diurnal cycles and seasonal trends from all datasets, we investigate dependence of correlation length on time scale by digitally high-pass filtering the data on 0.25-2000 h timescales and calculating correlations between sites for each high-pass filter cut-off. Correlations fall to zero with increasing station separation distance, but the characteristic correlation length varies with the high-pass filter applied: the higher the cut-off frequency, the smaller the station separation required to achieve de-correlation. Remarkable similarities between these three datasets reveal behavior that, if universal, could be particularly useful for grid management. For high

Large-scale wind power in New Brunswick : a regional scenario study towards 2025

International Nuclear Information System (INIS)

2008-08-01

This paper discussed the large-scale development of wind power in New Brunswick and evaluated Danish experiences with wind development as a template for developing wind resources in the Maritimes region. The study showed that New Brunswick and the Maritimes region have good wind resources, and that the province will gain significant economic benefits from deploying between 5500 and 7500 MW of wind power capacity by 2025. Wind power development will contribute to the security of supply in the region and reduce air pollution. Carbon regulation and renewable portfolio standards will improve the competitiveness of wind power. Electricity generated by wind power plants in the Maritimes can be sold to other provinces in Canada, as well as to the heavily populated New England region of the United States. A high level of cooperation between markets in the Maritimes area and neighbouring New England and Quebec systems will be required in addition to load flow analyses of electricity systems. Denmark's experiences with developing wind power indicate that existing market designs must be restructured to allow for higher levels of competition. A strong system operator is required to integrate wind power into the system. It was concluded that strong political leadership is required to ensure the sustainable development of the region. 5 refs., 4 tabs., 9 figs

Reliability, availability and maintenance aspects of large-scale offshore wind farms, a concepts study

NARCIS (Netherlands)

Van Bussel, G.J.W.; Zaayer, M.B.

2001-01-01

The DOWEC projects aims at implementation of large wind turbines in large scale wind farms. part of the DOWEC project a concepts study was performed regarding the achievable reliability and availability levels. A reduction with a factor of 2 with regard to the present state of the art seems fairly

Scale Dependence of Magnetic Helicity in the Solar Wind

Science.gov (United States)

Brandenburg, Axel; Subramanian, Kandaswamy; Balogh, Andre; Goldstein, Melvyn L.

2011-01-01

We determine the magnetic helicity, along with the magnetic energy, at high latitudes using data from the Ulysses mission. The data set spans the time period from 1993 to 1996. The basic assumption of the analysis is that the solar wind is homogeneous. Because the solar wind speed is high, we follow the approach first pioneered by Matthaeus et al. by which, under the assumption of spatial homogeneity, one can use Fourier transforms of the magnetic field time series to construct one-dimensional spectra of the magnetic energy and magnetic helicity under the assumption that the Taylor frozen-in-flow hypothesis is valid. That is a well-satisfied assumption for the data used in this study. The magnetic helicity derives from the skew-symmetric terms of the three-dimensional magnetic correlation tensor, while the symmetric terms of the tensor are used to determine the magnetic energy spectrum. Our results show a sign change of magnetic helicity at wavenumber k approximately equal to 2AU(sup -1) (or frequency nu approximately equal to 2 microHz) at distances below 2.8AU and at k approximately equal to 30AU(sup -1) (or nu approximately equal to 25 microHz) at larger distances. At small scales the magnetic helicity is positive at northern heliographic latitudes and negative at southern latitudes. The positive magnetic helicity at small scales is argued to be the result of turbulent diffusion reversing the sign relative to what is seen at small scales at the solar surface. Furthermore, the magnetic helicity declines toward solar minimum in 1996. The magnetic helicity flux integrated separately over one hemisphere amounts to about 10(sup 45) Mx(sup 2) cycle(sup -1) at large scales and to a three times lower value at smaller scales.

Application of bamboo laminates in large-scale wind turbine blade design?

Institute of Scientific and Technical Information of China (English)

Long WANG; Hui LI; Tongguang WANG

2016-01-01

From the viewpoint of material and structure in the design of bamboo blades of large-scale wind turbine, a series of mechanical property tests of bamboo laminates as the major enhancement materials for blades are presented. The basic mechanical characteristics needed in the design of bamboo blades are brie?y introduced. Based on these data, the aerodynamic-structural integrated design of a 1.5 MW wind turbine bamboo blade relying on a conventional platform of upwind, variable speed, variable pitch, and doubly-fed generator is carried out. The process of the structural layer design of bamboo blades is documented in detail. The structural strength and fatigue life of the designed wind turbine blades are certified. The technical issues raised from the design are discussed. Key problems and direction of the future study are also summarized.

Determination of Scaled Wind Turbine Rotor Characteristics from Three Dimensional RANS Calculations

International Nuclear Information System (INIS)

Burmester, S; Gueydon, S; Make, M

2016-01-01

Previous studies have shown the importance of 3D effects when calculating the performance characteristics of a scaled down turbine rotor [1-4]. In this paper the results of 3D RANS (Reynolds-Averaged Navier-Stokes) computations by Make and Vaz [1] are taken to calculate 2D lift and drag coefficients. These coefficients are assigned to FAST (Blade Element Momentum Theory (BEMT) tool from NREL) as input parameters. Then, the rotor characteristics (power and thrust coefficients) are calculated using BEMT. This coupling of RANS and BEMT was previously applied by other parties and is termed here the RANS-BEMT coupled approach. Here the approach is compared to measurements carried out in a wave basin at MARIN applying Froude scaled wind, and the direct 3D RANS computation. The data of both a model and full scale wind turbine are used for the validation and verification. The flow around a turbine blade at full scale has a more 2D character than the flow properties around a turbine blade at model scale (Make and Vaz [1]). Since BEMT assumes 2D flow behaviour, the results of the RANS-BEMT coupled approach agree better with the results of the CFD (Computational Fluid Dynamics) simulation at full- than at model-scale. (paper)

Status of the technology development of large scale HTS generators for wind turbine

Energy Technology Data Exchange (ETDEWEB)

Le, T. D.; Kim, J. H.; Kim, D. J.; Boo, C. J.; Kim, H. M. [Jeju National University, Jeju (Korea, Republic of)

2015-06-15

Large wind turbine generators with high temperature superconductors (HTS) are in incessant development because of their advantages such as weight and volume reduction and the increased efficiency compared with conventional technologies. In addition, nowadays the wind turbine market is growing in a function of time, increasing the capacity and energy production of the wind farms installed and increasing the electrical power for the electrical generators installed. As a consequence, it is raising the wind power energy contribution for the global electricity demand. In this study, a forecast of wind energy development will be firstly emphasized, then it continue presenting a recent status of the technology development of large scale HTSG for wind power followed by an explanation of HTS wire trend, cryogenics cooling systems concept, HTS magnets field coil stability and other technological parts for optimization of HTS generator design-operating temperature, design topology, field coil shape and level cost of energy, as well. Finally, the most relevant projects and designs of HTS generators specifically for offshore wind power systems are also mentioned in this study.

Status of the technology development of large scale HTS generators for wind turbine

International Nuclear Information System (INIS)

Le, T. D.; Kim, J. H.; Kim, D. J.; Boo, C. J.; Kim, H. M.

2015-01-01

Large wind turbine generators with high temperature superconductors (HTS) are in incessant development because of their advantages such as weight and volume reduction and the increased efficiency compared with conventional technologies. In addition, nowadays the wind turbine market is growing in a function of time, increasing the capacity and energy production of the wind farms installed and increasing the electrical power for the electrical generators installed. As a consequence, it is raising the wind power energy contribution for the global electricity demand. In this study, a forecast of wind energy development will be firstly emphasized, then it continue presenting a recent status of the technology development of large scale HTSG for wind power followed by an explanation of HTS wire trend, cryogenics cooling systems concept, HTS magnets field coil stability and other technological parts for optimization of HTS generator design-operating temperature, design topology, field coil shape and level cost of energy, as well. Finally, the most relevant projects and designs of HTS generators specifically for offshore wind power systems are also mentioned in this study

Indirect solar wind geothermal: Alternative energy sources 4, volume 4

Science.gov (United States)

Veziroglu, T. N.

The utilities are obliged to provide electricity in a reliable and cost effective manner. Some unique problems posed by large scale wind turbines as an electricity source have to be considered. A value model is presented which is based upon the fuel displacement capability and the capacity displacement capability of wind turbines. The amount of fossil fuels which is saved by wind turbines depends on the forecasted wind power output, the actual power output fluctuations of the wind turbines and on system operation. The highly controversial capacity credit of wind turbines is discussed under the aspect of system reliability. It is shown that calculations of the capacity credit should be based upon detailed investigations with regard to the time dependence of the hourly wind power output.

A GIS wind resource map with tabular printout of monthly and annual wind speeds for 2,000 towns in Iowa

Energy Technology Data Exchange (ETDEWEB)

Brower, M.C. [Brower & Company, Andover, MA (United States); Factor, T. [Iowa Wind Energy Institute, Fairfield, IA (United States)

1997-12-31

The Iowa Wind Energy Institute, under a grant from the Iowa Energy Center, undertook in 1994 to map wind resources in Iowa. Fifty-meter met towers were erected at 13 locations across the state deemed promising for utility-scale wind farm development. Two years of summarized wind speed, direction, and temperature data were used to create wind resource maps incorporating effects of elevation, relative exposure, terrain roughness, and ground cover. Maps were produced predicting long-term mean monthly and annual wind speeds on a one-kilometer grid. The estimated absolute standard error in the predicted annual average wind speeds at unobstructed locations is 9 percent. The relative standard error between points on the annual map is estimated to be 3 percent. These maps and tabular data for 2,000 cities and towns in Iowa are now available on the Iowa Energy Center`s web site (http.//www.energy.iastate.edu).

2012 Market Report on U.S. Wind Technologies in Distributed Applications

Energy Technology Data Exchange (ETDEWEB)

Orrell, Alice C.; Flowers, L. T.; Gagne, M. N.; Pro, B. H.; Rhoads-Weaver, H. E.; Jenkins, J. O.; Sahl, K. M.; Baranowski, R. E.

2013-08-06

At the end of 2012, U.S. wind turbines in distributed applications reached a 10-year cumulative installed capacity of more than 812 MW from more than 69,000 units across all 50 states. In 2012 alone, nearly 3,800 wind turbines totaling 175 MW of distributed wind capacity were documented in 40 states and in the U.S. Virgin Islands, with 138 MW using utility-scale turbines (i.e., greater than 1 MW in size), 19 MW using mid-size turbines (i.e., 101 kW to 1 MW in size), and 18.4 MW using small turbines (i.e., up to 100 kW in size). Distributed wind is defined in terms of technology application based on a wind project’s location relative to end-use and power-distribution infrastructure, rather than on technology size or project size. Distributed wind systems are either connected on the customer side of the meter (to meet the onsite load) or directly to distribution or micro grids (to support grid operations or offset large loads nearby). Estimated capacity-weighted average costs for 2012 U.S. distributed wind installations was $2,540/kW for utility-scale wind turbines, $2,810/kW for mid-sized wind turbines, and $6,960/kW for newly manufactured (domestic and imported) small wind turbines. An emerging trend observed in 2012 was an increased use of refurbished turbines. The estimated capacity-weighted average cost of refurbished small wind turbines installed in 2012 was $4,080/kW. As a result of multiple projects using utility-scale turbines, Iowa deployed the most new overall distributed wind capacity, 37 MW, in 2012. Nevada deployed the most small wind capacity in 2012, with nearly 8 MW of small wind turbines installed in distributed applications. In the case of mid-size turbines, Ohio led all states in 2012 with 4.9 MW installed in distributed applications. State and federal policies and incentives continued to play a substantial role in the development of distributed wind projects. In 2012, U.S. Treasury Section 1603 payments and grants and loans from the U

Down-scaling wind energy resource from mesoscale to local scale by nesting and data assimilation with a CFD model

International Nuclear Information System (INIS)

Duraisamy Jothiprakasam, Venkatesh

2014-01-01

The development of wind energy generation requires precise and well-established methods for wind resource assessment, which is the initial step in every wind farm project. During the last two decades linear flow models were widely used in the wind industry for wind resource assessment and micro-siting. But the linear models inaccuracies in predicting the wind speeds in very complex terrain are well known and led to use of CFD, capable of modeling the complex flow in details around specific geographic features. Mesoscale models (NWP) are able to predict the wind regime at resolutions of several kilometers, but are not well suited to resolve the wind speed and turbulence induced by the topography features on the scale of a few hundred meters. CFD has proven successful in capturing flow details at smaller scales, but needs an accurate specification of the inlet conditions. Thus coupling NWP and CFD models is a better modeling approach for wind energy applications. A one-year field measurement campaign carried out in a complex terrain in southern France during 2007-2008 provides a well-documented data set both for input and validation data. The proposed new methodology aims to address two problems: the high spatial variation of the topography on the domain lateral boundaries, and the prediction errors of the mesoscale model. It is applied in this work using the open source CFD code Code-Saturne, coupled with the mesoscale forecast model of Meteo-France (ALADIN). The improvement is obtained by combining the mesoscale data as inlet condition and field measurement data assimilation into the CFD model. Newtonian relaxation (nudging) data assimilation technique is used to incorporate the measurement data into the CFD simulations. The methodology to reconstruct long term averages uses a clustering process to group the similar meteorological conditions and to reduce the number of CFD simulations needed to reproduce 1 year of atmospheric flow over the site. The assimilation

A nonlinear dynamics approach for incorporating wind-speed patterns into wind-power project evaluation.

Science.gov (United States)

Huffaker, Ray; Bittelli, Marco

2015-01-01

Wind-energy production may be expanded beyond regions with high-average wind speeds (such as the Midwest U.S.A.) to sites with lower-average speeds (such as the Southeast U.S.A.) by locating favorable regional matches between natural wind-speed and energy-demand patterns. A critical component of wind-power evaluation is to incorporate wind-speed dynamics reflecting documented diurnal and seasonal behavioral patterns. Conventional probabilistic approaches remove patterns from wind-speed data. These patterns must be restored synthetically before they can be matched with energy-demand patterns. How to accurately restore wind-speed patterns is a vexing problem spurring an expanding line of papers. We propose a paradigm shift in wind power evaluation that employs signal-detection and nonlinear-dynamics techniques to empirically diagnose whether synthetic pattern restoration can be avoided altogether. If the complex behavior of observed wind-speed records is due to nonlinear, low-dimensional, and deterministic system dynamics, then nonlinear dynamics techniques can reconstruct wind-speed dynamics from observed wind-speed data without recourse to conventional probabilistic approaches. In the first study of its kind, we test a nonlinear dynamics approach in an application to Sugarland Wind-the first utility-scale wind project proposed in Florida, USA. We find empirical evidence of a low-dimensional and nonlinear wind-speed attractor characterized by strong temporal patterns that match up well with regular daily and seasonal electricity demand patterns.

Wind Generators

Science.gov (United States)

1989-01-01

When Enerpro, Inc. president, Frank J. Bourbeau, attempted to file a patent on a system for synchronizing a wind generator to the electric utility grid, he discovered Marshall Space Flight Center's Frank Nola's power factor controller. Bourbeau advanced the technology and received a NASA license and a patent for his Auto Synchronous Controller (ASC). The ASC reduces generator "inrush current," which occurs when large generators are abruptly brought on line. It controls voltage so the generator is smoothly connected to the utility grid when it reaches its synchronous speed, protecting the components from inrush current damage. Generator efficiency is also increased in light winds by applying lower than rated voltage. Wind energy is utilized to drive turbines to generate electricity for utility companies.

Adjustment of the Internal Tax Scale

CERN Multimedia

2013-01-01

In application of Article R V 2.03 of the Staff Regulations, the internal tax scale has been adjusted with effect on 1 January 2012. The new scale may be consulted via the CERN Admin e-guide.  The notification of internal annual tax certificate for the financial year 2012 takes into account this adjustment. HR Department (Tel. 73907)

Economics of Utility Scale Photovoltaics at Purdue University

Science.gov (United States)

Arnett, William

The research for this case study shows that utility scale solar photovoltaics has become a competitive energy investment option, even when a campus operates a power plant at low electricity rates. To evaluate this an economic model called SEEMS (Solar Economic Evaluation Modelling Spreadsheets) was developed to evaluate a number of financial scenarios in Real Time Pricing for universities. The three main financing structures considered are 1) land leasing, 2) university direct purchase, and 3) third party purchase. Unlike other commercially available models SEEMS specifically accounts for real time pricing, where the local utility provides electricity at an hourly rate that changes with the expected demand. In addition, SEEMS also includes a random simulation that allows the model to predict the likelihood of success for a given solar installation strategy. The research showed that there are several options for utility scale solar that are financially attractive. The most practical financing structure is with a third party partnership because of the opportunity to take advantage of tax incentives. Other options could become more attractive if non-financial benefits are considered. The case study for this research, Purdue University, has a unique opportunity to integrate utility-scale solar electricity into its strategic planning. Currently Purdue is updating its master plan which will define how land is developed. Purdue is also developing a sustainability plan that will define long term environmental goals. In addition, the university is developing over 500 acres of land west of campus as part of its Aerospace Innovation District. This research helps make the case for including utility-scale solar electricity as part of the university's strategic planning.

OffshoreDC DC grids for integration of large scale wind power

DEFF Research Database (Denmark)

Zeni, Lorenzo; Endegnanew, Atsede Gualu; Stamatiou, Georgios

The present report summarizes the main findings of the Nordic Energy Research project “DC grids for large scale integration of offshore wind power – OffshoreDC”. The project is been funded by Nordic Energy Research through the TFI programme and was active between 2011 and 2016. The overall...... objective of the project was to drive the development of the VSC based HVDC technology for future large scale offshore grids, supporting a standardised and commercial development of the technology, and improving the opportunities for the technology to support power system integration of large scale offshore...

Variability of sea ice deformation rates in the Arctic and their relationship with basin-scale wind forcing

Directory of Open Access Journals (Sweden)

A. Herman

2012-12-01

Full Text Available The temporal variability of the moments of probability distribution functions (pdfs of total sea ice deformation rates in the Arctic is analyzed in the context of the basin-scale wind forcing acting on the ice. The pdfs are estimated for 594 satellite-derived sea ice deformation maps from 11 winter seasons between 1996/1997 and 2007/2008, provided by the RADARSAT Geophysical Processor System. The temporal scale analyzed equals 3 days. The moments of the pdfs, calculated for a range of spatial scales (12.5–900 km, have two dominating components of variability: a seasonal cycle, with deformation rates decreasing throughout winter towards a minimum in March; and a short-term, synoptic variability, strongly correlated with the area-averaged magnitude of the wind stress over the Arctic, estimated based on the NCEP-DOE Reanalysis-2 data (correlation coefficient of 0.71 for the mean deformation rate. Due to scaling properties of the moments, logarithms of higher moments are strongly correlated with the wind stress as well. Exceptions are observed only at small spatial scales, as a result of extreme deformation events, not directly associated with large-scale wind forcing. By repeating the analysis within regions of different sizes and locations, we show that the wind–ice deformation correlation is largest at the basin scale and decreases with decreasing size of the area of study. Finally, we suggest that a positive trend in seasonally averaged correlation between sea ice deformation rates and the wind forcing, present in the analyzed data, may be related to an observed decrease in the multi-year ice area in the Arctic, indicating possibly even stronger correlations in the future.

Fabrication of a Scaled MgB2 Racetrack Demonstrator Pole for a 10-MW Direct-Drive Wind Turbine Generator

DEFF Research Database (Denmark)

Magnusson, Niklas; Eliassen, Jan Christian; Abrahamsen, Asger Bech

2018-01-01

Field windings made of MgB2 wires or tapes are considered for their potential to reduce volume, weight, and cost of large offshore wind turbine generators. To gain experience of how to use this relatively new material in full-scale generators, tests of different winding methodologies and techniques...... are needed. In this paper, we describe in detail the steps used to wind a racetrack coil with a length of 1 m and a width of 0.5 m out of 4.5 km of MgB2 superconducting tape. The width corresponds to a full-scale pole of a 10-MW generator, whereas the length of the straight section is shorter than...... the corresponding full-scale pole. The coil was built up of ten double pancake coils. Each double pancake coil was wet wound using a semiautomatic winding process, where Stycast 2850 was applied directly to the MgB2 tape without any other dedicated electrical insulation. The strengths and weaknesses of the winding...

Wind's share in global energy markets

International Nuclear Information System (INIS)

Madsen, B.T.

1997-01-01

The question of how great of a contribution wind power can really make to the world's energy needs is discussed. Emphasis up until recently has been mainly on improving wind turbine technology and siting practices as it is these that will provide an answer. The International Energy Agency predicts that world energy demand will increase by 30-50% by 2010. More countries than ever are either using wind power now or are preparing for its use. Wind power continues to improve its price competitiveness. There is enough wind to cover our energy needs many times over, according to some reports twice the world's electricity supply could be met by utilizing just 5-10% of areas identified as having average wind speeds of 5 m/s or greater - ignoring population centers, forests and specially protected areas. But a major limiting factor to utilizing the available wind resource is the established grid systems, which can only base 20% of supply on wind power. It is concluded that wind can contribute significantly to the world's energy needs in the next century and beyond. If wind, which has taken giant leaps in improving its competitiveness over the past 20 hears, can be a major energy contributor by early next century, other renewables such as solar and biomass might also evolve to become major contributors too. If so, renewables, including hydro, could conceivably cover 50% of our energy needs by the middle of the next century. Much will depend on decision-makers at the centers of power. For Europe and certain other areas of the world, policies governing cross-border trade of electricity as well as the framework for environmental protection related to energy production will determine the final outcome

On the estimation of wind comfort in a building environment by micro-scale simulation

Directory of Open Access Journals (Sweden)

Günter Gross

2014-06-01

Full Text Available A three-dimensional micro-scale model is used to study some aspects of wind comfort in a built-up area. The equations for calculating the mean wind have been extended by a Markov approach for short-term wind fluctuations. The model components have been successfully verified against wind tunnel measurements and observations of a field experiment. The simulated time series are used to estimate wind comfort measures. It turns out that the frequency of exceedance of prescribed thresholds depends strongly on the specification of the gust duration time. It was also possible to calculate the spatial distribution of a gust factor g$g$ depending on local wind characteristics. The simulated range is much broader than a value of g=3–3.5$g=3\\text{--}3.5$ commonly used for wind comfort assessments. Again, the order of magnitude and the bandwidth of g$g$ depends strongly on the definition of a gust.

Large-scale wind energy application. Transporting wind energy over long distances using an HVDC transmission line, in combination with hydro energy or biomass energy

International Nuclear Information System (INIS)

Coelingh, J.P.; Van Wijk, A.J.M.; Betcke, J.W.H.; Geuzendam, C.; Gilijamse, W.; Westra, C.A.; Curvers, A.P.W.M.; Beurskens, H.J.M.

1995-08-01

The main objective of the study on the title subject is to assess the long-term prospects for large-scale application of wind energy, in combination with hydro energy in Norway and in combination with biomass energy in Scotland. These countries have high wind resource areas, however they are located far away from load centres. The development of new transmission technologies as High Voltage Direct Current (HVDC) transmission lines, in combination with highly suitable places for wind energy in Norway and Scotland, forms the driving force behind this study. The following two cases are being considered: (1) a large-scale wind farm (1,000 MW) in Norway from which electricity is transmitted to The Netherlands by using an HVDC transmission line, in combination with hydro energy. Hydro energy already makes a large contribution to the energy supply of Norway. Wind farms can contribute to the electricity production and save hydro energy generated electricity and make the export of electricity profitable; and (2) a large-scale wind farm (1,000 MW) in Scotland from which electricity is transmitted to The Netherlands by using an HVDC transmission line, in combination with biomass energy. Scotland has a large potential for biomass production such as energy crops and forestry. Poplars and willows cultivated on set-aside land can be gasified and fed into modern combined-cycle plants to generate electricity. In Scotland the usable potential of wind energy may be limited in the short and medium term by the capacity of the grid. New connections can overcome this constraint and allow wind energy to be treated as a European Union resource rather than as a national resource. Thus, the concept of this study is to look at the possibilities of making a 1,000 MW link from The Netherlands to Norway or to Scotland, in order to supply electricity at competitive costs generated with renewable energy sources. 16 figs., 24 tabs., 80 refs

Vertical Axis Wind Turbine Design Load Cases Investigation and Comparison with Horizontal Axis Wind Turbine

DEFF Research Database (Denmark)

Galinos, Christos; Larsen, Torben J.; Aagaard Madsen, Helge

2016-01-01

The paper studies the applicability of the IEC 61400-1 ed.3, 2005 International Standard of wind turbine minimum design requirements in the case of an onshore Darrieus VAWT and compares the results of basic Design Load Cases (DLCs) with those of a 3-bladed HAWT. The study is based on aeroelastic...... computations using the HAWC2 aero-servo-elastic code A 2-bladed 5 MW VAWT rotor is used based on a modified version of the DeepWind rotor For the HAWT simulations the NREL 3-bladed 5 MW reference wind turbine model is utilized Various DLCs are examined including normal power production, emergency shut down...... and parked situations, from cut-in to cut-out and extreme wind conditions. The ultimate and 1 Hz equivalent fatigue loads of the blade root and turbine base bottom are extracted and compared in order to give an insight of the load levels between the two concepts. According to the analysis the IEC 61400-1 ed...

Toward Isolation of Salient Features in Stable Boundary Layer Wind Fields that Influence Loads on Wind Turbines

Directory of Open Access Journals (Sweden)

Jinkyoo Park

2015-04-01

Full Text Available Neutral boundary layer (NBL flow fields, commonly used in turbine load studies and design, are generated using spectral procedures in stochastic simulation. For large utility-scale turbines, stable boundary layer (SBL flow fields are of great interest because they are often accompanied by enhanced wind shear, wind veer, and even low-level jets (LLJs. The generation of SBL flow fields, in contrast to simpler stochastic simulation for NBL, requires computational fluid dynamics (CFD procedures to capture the physics and noted characteristics—such as shear and veer—that are distinct from those seen in NBL flows. At present, large-eddy simulation (LES is the most efficient CFD procedure for SBL flow field generation and related wind turbine loads studies. Design standards, such as from the International Electrotechnical Commission (IEC, provide guidance albeit with simplifying assumptions (one such deals with assuming constant variance of turbulence over the rotor and recommend standard target turbulence power spectra and coherence functions to allow NBL flow field simulation. In contrast, a systematic SBL flow field simulation procedure has not been offered for design or for site assessment. It is instructive to compare LES-generated SBL flow fields with stochastic NBL flow fields and associated loads which we evaluate for a 5-MW turbine; in doing so, we seek to isolate distinguishing characteristics of wind shear, wind veer, and turbulence variation over the rotor plane in the alternative flow fields and in the turbine loads. Because of known differences in NBL-stochastic and SBL-LES wind fields but an industry preference for simpler stochastic simulation in design practice, this study investigates if one can reproduce stable atmospheric conditions using stochastic approaches with appropriate corrections for shear, veer, turbulence, etc. We find that such simple tuning cannot consistently match turbine target SBL load statistics, even though

System Dynamics Simulation of Large-Scale Generation System for Designing Wind Power Policy in China

Directory of Open Access Journals (Sweden)

Linna Hou

2015-01-01

Full Text Available This paper focuses on the impacts of renewable energy policy on a large-scale power generation system, including thermal power, hydropower, and wind power generation. As one of the most important clean energy, wind energy has been rapidly developed in the world. But in recent years there is a serious waste of wind power equipment and investment in China leading to many problems in the industry from wind power planning to its integration. One way overcoming the difficulty is to analyze the influence of wind power policy on a generation system. This paper builds a system dynamics (SD model of energy generation to simulate the results of wind energy generation policies based on a complex system. And scenario analysis method is used to compare the effectiveness and efficiency of these policies. The case study shows that the combinations of lower portfolio goal and higher benchmark price and those of higher portfolio goal and lower benchmark price have large differences in both effectiveness and efficiency. On the other hand, the combinations of uniformly lower or higher portfolio goal and benchmark price have similar efficiency, but different effectiveness. Finally, an optimal policy combination can be chosen on the basis of policy analysis in the large-scale power system.

WINS. Market Simulation Tool for Facilitating Wind Energy Integration

Energy Technology Data Exchange (ETDEWEB)

Shahidehpour, Mohammad [Illinois Inst. of Technology, Chicago, IL (United States)

2012-10-30

Integrating 20% or more wind energy into the system and transmitting large sums of wind energy over long distances will require a decision making capability that can handle very large scale power systems with tens of thousands of buses and lines. There is a need to explore innovative analytical and implementation solutions for continuing reliable operations with the most economical integration of additional wind energy in power systems. A number of wind integration solution paths involve the adoption of new operating policies, dynamic scheduling of wind power across interties, pooling integration services, and adopting new transmission scheduling practices. Such practices can be examined by the decision tool developed by this project. This project developed a very efficient decision tool called Wind INtegration Simulator (WINS) and applied WINS to facilitate wind energy integration studies. WINS focused on augmenting the existing power utility capabilities to support collaborative planning, analysis, and wind integration project implementations. WINS also had the capability of simulating energy storage facilities so that feasibility studies of integrated wind energy system applications can be performed for systems with high wind energy penetrations. The development of WINS represents a major expansion of a very efficient decision tool called POwer Market Simulator (POMS), which was developed by IIT and has been used extensively for power system studies for decades. Specifically, WINS provides the following superiorities; (1) An integrated framework is included in WINS for the comprehensive modeling of DC transmission configurations, including mono-pole, bi-pole, tri-pole, back-to-back, and multi-terminal connection, as well as AC/DC converter models including current source converters (CSC) and voltage source converters (VSC); (2) An existing shortcoming of traditional decision tools for wind integration is the limited availability of user interface, i.e., decision

Wind energy systems

International Nuclear Information System (INIS)

Richardson, R.D.; McNerney, G.M.

1993-01-01

Wind energy has matured to a level of development where it is ready to become a generally accepted utility generation technology. A brief discussion of this development is presented, and the operating and design principles are discussed. Alternative designs for wind turbines and the tradeoffs that must be considered are briefly compared. Development of a wind energy system and the impacts on the utility network including frequency stability, voltage stability, and power quality are discussed. The assessment of wind power station economics and the key economic factors that determine the economic viability of a wind power plant are presented

Effects of distributing wind energy generation over Europe

Energy Technology Data Exchange (ETDEWEB)

Giebel, G [Risoe National Lab., Wind Energy and Atmospheric Physics Dept., Roskilde (Denmark)

1999-03-01

Using data from 60 meteorological stations distributed all over Europe in conjunction with the National Grid Model (NGM) from the Rutherford Appleton Laboratory, the effects of the large-scale distribution of wind energy generation are studied. In some regions of Europe, wind energy already covers a significant proportion of the electricity demand. But the intermittence of the wind resource is always a limiting factor when penetration levels are high. Studies for single countries have shown that distributing the generation over a large area reduces the variability of the output and hence makes wind energy more appealing to utilities, since the stability requirement of the network are easier to fulfil. The data are analysed in terms of absolute highs and lows, temporal and spatial correlations. To assess the financial benefits, the NGM is used to evaluate the match of electricity demand and generation as well as the possibel savings of fossil fuel in an electricity grid incorporating various capacities of wind energy generation. To assess the value of wind energy on a trans-national scale, the European plant mix is modelled, and the NGM is used to simulate the scheduling of these plants in the presence of different penetrations of wind energy. (au) EU-JOULE-3. 11 refs.

Solar wind fluctuations at large scale: A comparison between low and high solar activity conditions

International Nuclear Information System (INIS)

Bavassano, B.; Bruno, R.

1991-01-01

The influence of the Sun's activity cycle on the solar wind fluctuations at time scales from 1 hour to 3 days in the inner heliosphere (0.3 to 1 AU) is investigated. Hourly averages of plasma and magnetic field data by Helios spacecraft are used. Since fluctuations behave quite differently with changing scale, the analysis is performed separately for two different ranges in time scale. Between 1 and 6 hours Alfvenic fluctuations and pressure-balanced structures are extensively observed. At low solar activity and close to 0.3 AU, Alfvenic fluctuations are more frequent than pressure-balanced structures. This predominance, however, weakens for rising solar activity and radial distance, to the point that a role exchange, in terms of occurrence rate, is found at the maximum of the cycle close to 1 AU. On the other hand, in all cases Alfvenic fluctuations have a larger amplitude than pressure-balanced structures. On the whole, the Alfvenic contribution to the solar wind energy spectrum comes out to be dominant at all solar activity conditions. At scales from 0.5 to 3 days the most important feature is the growth, as the solar wind expansion develops, of strong positive correlations between magnetic and thermal pressures. These structures are progressively built up by the interaction between different wind flows. This effect is more pronounced at low than at high activity. Our findings support the conclusion that the solar cycle evolution of the large-scale velocity pattern is the factor governing the observed variations

Distributed Wind Resource Assessment: State of the Industry

Energy Technology Data Exchange (ETDEWEB)

Fields, Jason [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tinnesand, Heidi [National Renewable Energy Lab. (NREL), Golden, CO (United States); Baring-Gould, Ian [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-06-01

In support of the U.S. Department of Energy (DOE) Wind and Water Power Technologies Office (WWPTO) goals, researchers from DOE's National Renewable Energy Laboratory (NREL), National Wind Technology Center (NWTC) are investigating the Distributed Wind Resource Assessment (DWRA) process, which includes pre-construction energy estimation as well as turbine site suitability assessment. DWRA can have a direct impact on the Wind Program goals of maximizing stakeholder confidence in turbine performance and safety as well as reducing the levelized cost of energy (LCOE). One of the major components of the LCOE equation is annual energy production. DWRA improvements can maximize the annual energy production, thereby lowering the overall LCOE and improving stakeholder confidence in the distributed wind technology sector by providing more accurate predictions of power production. Over the long term, one of the most significant benefits of a more defined DWRA process could be new turbine designs, tuned to site-specific characteristics that will help the distributed wind industry follow a similar trajectory to the low-wind-speed designs in the utility-scale industry sector. By understanding the wind resource better, the industry could install larger rotors, capture more energy, and as a result, increase deployment while lowering the LCOE. a direct impact on the Wind Program goals of maximizing stakeholder confidence in turbine performance and safety as well as reducing the levelized cost of energy (LCOE). One of the major components of the LCOE equation is annual energy production. DWRA improvements can maximize the annual energy production, thereby lowering the overall LCOE and improving stakeholder confidence in the distributed wind technology sector by providing more accurate predictions of power production. Over the long term, one of the most significant benefits of a more defined DWRA process could be new turbine designs, tuned to site-specific characteristics that

Establishment of a National Wind Energy Center at University of Houston

Energy Technology Data Exchange (ETDEWEB)

Wang, Su Su [Univ. of Houston, TX (United States)

2016-10-31

The DOE-supported project objectives are to: establish a national wind energy center (NWEC) at University of Houston and conduct research to address critical science and engineering issues for the development of future large MW-scale wind energy production systems, especially offshore wind turbines. The goals of the project are to: (1) establish a sound scientific/technical knowledge base of solutions to critical science and engineering issues for developing future MW-scale large wind energy production systems, (2) develop a state-of-the-art wind rotor blade research facility at the University of Houston, and (3) through multi-disciplinary research, introducing technology innovations on advanced wind-turbine materials, processing/manufacturing technology, design and simulation, testing and reliability assessment methods related to future wind turbine systems for cost-effective production of offshore wind energy. To achieve the goals of the project, the following technical tasks were planned and executed during the period from April 15, 2010 to October 31, 2014 at the University of Houston: (1) Basic research on large offshore wind turbine systems (2) Applied research on innovative wind turbine rotors for large offshore wind energy systems (3) Integration of offshore wind-turbine design, advanced materials and manufacturing technologies (4) Integrity and reliability of large offshore wind turbine blades and scaled model testing (5) Education and training of graduate and undergraduate students and post- doctoral researchers (6) Development of a national offshore wind turbine blade research facility The research program addresses both basic science and engineering of current and future large wind turbine systems, especially offshore wind turbines, for MW-scale power generation. The results of the research advance current understanding of many important scientific issues and provide technical information for solving future large wind turbines with advanced design

Influence of time scale wind speed data on sustainability analysis for irrigating greenhouse crops

Science.gov (United States)

Díaz Méndez, Rodrigo; García Llaneza, Joaquín; Peillón, Manuel; Perdigones, Alicia; Sanchez, Raul; Tarquis, Ana M.; Garcia, Jose Luis

2014-05-01

Appropriate water supply at crop/farm level, with suitable costs, is becoming more and more important. Energy management is closely related to water supply in this context, being wind energy one of the options to be considered, using wind pumps for irrigation water supply. Therefore, it is important to characterize the wind speed frequency distribution to study the technical feasibility to use its energy for irrigation management purpose. The general objective of this present research is to analyze the impact of time scale recorded wind speed data in the sustainability for tomato (Solanum lycopersicum L.) grown under greenhouse at Cuban conditions using drip irrigation system. For this porpoise, a daily estimation balance between water needs and water availability was used to evaluate the feasibility of the most economic windmill irrigation system. Several factors were included: wind velocity (W, m/s) in function of the time scale averaged, flow supplied by the wind pump as a function of the elevation height (H, m) and daily greenhouse evapotranspiration. Monthly volumes of water required for irrigation (Dr, m3/ha) and in the water tank (Vd, m3), as well as the monthly irrigable area (Ar, ha), were estimated by cumulative deficit water budgeting taking in account these factors. Three-hourly wind velocity (W3h, m/s) data from 1992 till 2008 was available for this study. The original data was grouped in six and twelve hourly data (W6h and W12h respectively) as well as daily data (W24h). For each time scale the daily estimation balance was applied. A comparison of the results points out a need for at least three-hourly data to be used mainly in the months in which mean wind speed are close or below the pumps threshold speed to start-up functioning. References Manuel Esteban Peillon Mesa, Ana Maria Tarquis Alfonso, José Luis García Fernández, and Raúl Sánchez Calvo. The use of wind pumps for irrigating greenhouse tomato crops: a case study in Cuba. Geophysical

Scaling Relations of Starburst-driven Galactic Winds

International Nuclear Information System (INIS)

Tanner, Ryan; Cecil, Gerald; Heitsch, Fabian

2017-01-01

Using synthetic absorption lines generated from 3D hydrodynamical simulations, we explore how the velocity of a starburst-driven galactic wind correlates with the star formation rate (SFR) and SFR density. We find strong correlations for neutral and low ionized gas, but no correlation for highly ionized gas. The correlations for neutral and low ionized gas only hold for SFRs below a critical limit set by the mass loading of the starburst, above which point the scaling relations flatten abruptly. Below this point the scaling relations depend on the temperature regime being probed by the absorption line, not on the mass loading. The exact scaling relation depends on whether the maximum or mean velocity of the absorption line is used. We find that the outflow velocity of neutral gas can be up to five times lower than the average velocity of ionized gas, with the velocity difference increasing for higher ionization states. Furthermore, the velocity difference depends on both the SFR and mass loading of the starburst. Thus, absorption lines of neutral or low ionized gas cannot easily be used as a proxy for the outflow velocity of the hot gas.

Scaling Relations of Starburst-driven Galactic Winds

Energy Technology Data Exchange (ETDEWEB)

Tanner, Ryan [Department of Chemistry and Physics, Augusta University, Augusta, GA 30912 (United States); Cecil, Gerald; Heitsch, Fabian, E-mail: rytanner@augusta.edu [Department of Physics and Astronomy, University of North Carolina at Chapel Hill, Chapel Hill, NC 27599-3255 (United States)

2017-07-10

Using synthetic absorption lines generated from 3D hydrodynamical simulations, we explore how the velocity of a starburst-driven galactic wind correlates with the star formation rate (SFR) and SFR density. We find strong correlations for neutral and low ionized gas, but no correlation for highly ionized gas. The correlations for neutral and low ionized gas only hold for SFRs below a critical limit set by the mass loading of the starburst, above which point the scaling relations flatten abruptly. Below this point the scaling relations depend on the temperature regime being probed by the absorption line, not on the mass loading. The exact scaling relation depends on whether the maximum or mean velocity of the absorption line is used. We find that the outflow velocity of neutral gas can be up to five times lower than the average velocity of ionized gas, with the velocity difference increasing for higher ionization states. Furthermore, the velocity difference depends on both the SFR and mass loading of the starburst. Thus, absorption lines of neutral or low ionized gas cannot easily be used as a proxy for the outflow velocity of the hot gas.

Development of large scale and wind energy conservation system. Operational studies on a large-scale wind energy conservation system; Ogata furyoku hatsuden system no kaihatsu. Ogata furyoku hatsuden system no unten kenkyu

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for operational studies on a large-scale wind energy conversion system. A total of 8 domestic and foreign cases are studied for wind energy conversion cost, to clarify the causes for higher cost of the Japanese system. The wind power systems studied include Japanese (5 units at Tappi Wind Park, the same type supplied by company M), US (California Wind Farm, 300 units) and UK (Wales Wind Farm, 103 units) systems. The investment costs are 639, 285 and 189 thousand yen/kW for the Japanese, US and UK systems, respectively. It is also revealed that the power plant itself and assembling costs account for a majority (70 to 88%) of the total investment cost. The higher cost of the Japanese system results from a smaller number of units installed, and the power plant cost can be drastically reduced by mass production. Increasing size also reduces cost greatly.

The potential of wind farms

International Nuclear Information System (INIS)

Hauge Madsen, P.; Lundsager, P.

1992-09-01

Papers presented at the European wind energy conference on the potential of wind farms are presented. The aim of the conference was to bring into focus the problems, experiences and potential of the application of wind power in wind power farms as a contribution to the European and global energy supply. It was considered that the interchange of experience among representatives of science, utilities, industry, environment and energy planning, together with those who represent financial and insurance interests, would create a better understanding of all aspects of wind power for its future successful development. The subjects covered concern surveys of national planning and policies regarding wind energy utilization and national and global development of wind turbine arrays. The performance of some individual wind farms is described. Papers also deal with utility and project planning, wind prediction and certification, wind loads and fatigus, wakes, noise and control. (AB)

The potential of wind farms

International Nuclear Information System (INIS)

Hauge Madsen, P.; Lundsager, P.

1992-09-01

Papers presented at the European wind energy conference on the potential of wind farms are presented. The aim of the conference was to bring into focus the problems, experiences and potential of the application of wind power in wind power farms as a contribution to the European and global energy supply. It was considered that the interchange of experience among representatives of science, utilities, industry, environment and energy planning, together with those who represent financial and insurance interests, would create a better understanding of all aspects of wind power for its future successful development. The subjects covered concern surveys of national planning and policies regarding wind energy utilization and national and global development of wind turbine arrays. The performance of some individual wind farms is described. Papers also deal with utility and project planning, wind prediction and certification, wind loads and fatigues, wakes, noise and control. (AB)

International wind energy development. World market update 2009. Forecast 2010-2014

Energy Technology Data Exchange (ETDEWEB)

2010-03-15

This is the fifteenth edition of the annual World Market Update produced by BTM Consult ApS, and covers developments in the wind energy sector during 2009. As in previous editions, the report also assesses important changes over the last three years and forecasts progress for five years ahead. The special topic in this year's WMU is an evaluation of the aftermath of the COP-15 climate change negotiations in relation to future wind power development. The global market for wind power not only produced a record for new installations in 2009 of 38 GW installed capacity, it also created a new order in the balance of international wind power. The rapid increase in the rate of installations in both Asia and the US was already clear in 2008; that trend has continued at a faster pace in 2009. By far the largest number of new wind projects were seen in the US and China. Another new reality is that most of the world's manufacturing of wind turbines now takes place in China. As a result three Chinese companies are among the world's top ten turbine manufacturers. At the same time a rapid expansion of manufacturing capacity by European turbine makers has taken place in the US. Europe contributed 28.2% of the newly added capacity - 10,738 MW - taking the continent's total wind power generation capacity to 76,553 MW. The growth in Asia's markets has once again been staggering. With 14,991 MW of new installations, South and East Asia accounted for 39.4% of the global total in 2009. China was the major contributor, with 13,750 MW of new capacity, more than double that installed in 2008. In terms of cumulative installed wind power, the US is still the world leader, with 35,159 MW. China overtook Germany with a margin of less than 50 MW. China now has a total of 25,853 MW, followed by Germany's 25,813 MW. A new world order in wind power has become a reality. The forecast released in this WMU shows an average growth rate of 13.5% for the period 2010

Full scale monitoring of wind and traffic induced response of a suspension bridge

Directory of Open Access Journals (Sweden)

Cheynet Etienne

2015-01-01

Full Text Available This paper presents a full-scale analysis of wind and traffic-induced vibrations of a long-span suspension bridge in complex terrain. Several wind and acceleration sensors have been installed along the main span on Lysefjord Bridge in Norway. In the present study, three days of continuous records are analysed. Traffic-induced vibrations are dominant at low and moderated wind speed, with non-negligible effects on the overall bridge response for heavy vehicles only. Traffic and wind-induced vibrations are compared in terms of root mean square of the acceleration response, and three simples approaches are proposed to isolate records dominated by wind-induced vibration. The first one relies on the separation of nocturnal and diurnal samples. The second one is based on the evaluation of the time-varying root mean square of the acceleration response. The last one evaluates the relative importance of the high frequency domain of the acceleration bridge response. It appears that traffic-induced vibrations may have to be taken into account for the buffeting analysis of long-span bridge under moderated wind.

Discord amongst the wind turbine buyers with regard to Dutch wind turbine manufacturers

International Nuclear Information System (INIS)

Janse, F.

1992-01-01

In the Netherlands two medium-large manufacturers of wind turbines exist: NedWind (Hollandia Kloos) and Windmaster Nederland (Begemann Groep). Also Lagerwey, which constructs wind turbines for the private market (farmers, cooperatives), is important for the Dutch market and successfull in Germany. There is a tendency amongst the Dutch energy utilities, which cooperate in the foundation WindPlan, to buy wind turbines from foreign manufacturers. Some energy utilities want to take advantage of the most attractive offers, while others want to cooperate in building up a Dutch wind turbine industry. 5 ills

2015 Cost of Wind Energy Review

Energy Technology Data Exchange (ETDEWEB)

Moné, Christopher [National Renewable Energy Lab. (NREL), Golden, CO (United States); Hand, Maureen [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bolinger, Mark [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Rand, Joseph [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Heimiller, Donna [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ho, Jonathan [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-06-27

This report uses representative utility-scale projects to estimate the levelized cost of energy (LCOE) for land-based and offshore wind plants in the United States. Data and results detailed here are derived from 2015 commissioned plants. More specifically, analysis detailed here relies on recent market data and state-of-the-art modeling capabilities to maintain an up-to-date understanding of wind energy cost trends and drivers. It is intended to provide insight into current component-level costs as well as a basis for understanding variability in LCOE across the industry. This publication reflects the fifth installment of this annual report.

Wind power in Arctic regions

International Nuclear Information System (INIS)

Lundsager, P.; Ahm, P.; Madsen, B.; Krogsgaard, P.

1993-07-01

Arctic or semi-arctic regions are often endowed with wind resources adequate for a viable production of electricity from the wind. Only limited efforts have so far been spent to introduce and to demonstrate the obvious synergy of combining wind power technology with the problems and needs of electricity generation in Arctic regions. Several factors have created a gap preventing the wind power technology carrying its full role in this context, including a certain lack of familiarity with the technology on the part of the end-users, the local utilities and communities, and a lack of commonly agreed techniques to adapt the same technology for Arctic applications on the part of the manufacturers. This report is part of a project that intends to contribute to bridging this gap. The preliminary results of a survey conducted by the project are included in this report, which is a working document for an international seminar held on June 3-4, 1993, at Risoe National Laboratory, Denmark. Following the seminar a final report will be published. It is intended that the final report will serve as a basis for a sustained, international effort to develop the wind power potential of the Arctic and semi-arctic regions. The project is carried out by a project group formed by Risoe, PA Energy and BTM Consult. The project is sponsored by the Danish Energy Agency of the Danish Ministry of Energy through grant no. ENS-51171/93-0008. (au)

Solar and wind energy utilization at Sarawak Southern national parks

International Nuclear Information System (INIS)

Abdul Rahman, N.; Kolot, A.

2006-01-01

The intentions of renewable energy utilization in Sarawak national parks were to reduce the environmental impacts to the protected surrounding and to overcome fuel transportation problem, as most national parks in Sarawak are not viable for the state electricity grid connection. The study was conducted at three national parks in southern Sarawak; viz. Samusan, Tanjung Datu and Pulau Talang-Talang Besar National Park. The study focused on the effectiveness of the system implementation, energy load and associated problems. Both Samusan and Tanjung Datu National systems are hybrids, which consist of solar photovoltaic panels, wind turbine and diesel generators, whereas, Pulau Talang-Talang Besar National Park is a stand alone system of solar photovoltaic panels only. In addition, the inefficient energy usage was observed at Samusan National Park. The study have identified that lack of local expertise, spare parts availability, transportation and inefficient energy management as the major problems associated to the solar and wind energy system in all national parks studied. Albeit the problems mentioned, the study discovered that the systems were acceptably reliable and satisfactorily supply fraction of the energy requirements to the national parks communities

Vertical-axial component wind turbine with a high coefficient using for wind energy

International Nuclear Information System (INIS)

Yersin, Ch. Sh.; Manatbev, R.K.; Yersina, A. K.; Tulepbergenov, A. K.

2012-01-01

The report presents the results of research and development on of promising wind units carousel type with a high ratio utilization of wind energy. This devices use a well-known invention – the wind turbine Darrieus. The rotation of the turbine is due to the action of ascensional power to aerodynamic well-streamlined symmetrical about the chord wing profiles of NASA, which are working wind turbine blades. The shaft rotation can be connected with the working blades of one of two ways: using the “swings” or the way “troposkino”. Darrieus turbine has a ratio utilization of wind energy xmax=045. Despite the fact that this is a good indicator of the efficiency of the turbine working, the proposed option allows us to significantly increase the value of this coefficient. The bases methodology of this research is a method of technical and technological research and development design of prospective wind energy construction (WES). Key words: wind turbine, the blade, coefficient utilization of wind energy

A Statistical Model for Hourly Large-Scale Wind and Photovoltaic Generation in New Locations

DEFF Research Database (Denmark)

Ekstrom, Jussi; Koivisto, Matti Juhani; Mellin, Ilkka

2017-01-01

The analysis of large-scale wind and photovoltaic (PV) energy generation is of vital importance in power systems where their penetration is high. This paper presents a modular methodology to assess the power generation and volatility of a system consisting of both PV plants (PVPs) and wind power...... of new PVPs and WPPs in system planning. The model is verified against hourly measured wind speed and solar irradiance data from Finland. A case study assessing the impact of the geographical distribution of the PVPs and WPPs on aggregate power generation and its variability is presented....

Study on Modelling Standardization of Double-fed Wind Turbine and Its Application

Directory of Open Access Journals (Sweden)

Li Xiang

2016-01-01

Full Text Available Based on the standardized modelling of the International Modelling Team, study on double-fed induction generator (DFIG wind turbine is processed in this paper, aiming at capability of universally and reasonably reflecting key performance related to large scale system analysis. The standardized model proposed is of high degree of structural modularity, easy functional extension and universalization of control strategy and signal. Moreover, it is applicable for wind turbines produced by different manufacturers through model parameter adjustment. The complexity of the model can meet both needs of grid-connected characteristic simulation of wind turbine and large scale power system simulation.

The impact of photovoltaic (PV) installations on downwind particulate matter concentrations: Results from field observations at a 550-MWAC utility-scale PV plant.

Science.gov (United States)

Ravikumar, Dwarakanath; Sinha, Parikhit

2017-10-01

With utility-scale photovoltaic (PV) projects increasingly developed in dry and dust-prone geographies with high solar insolation, there is a critical need to analyze the impacts of PV installations on the resulting particulate matter (PM) concentrations, which have environmental and health impacts. This study is the first to quantify the impact of a utility-scale PV plant on PM concentrations downwind of the project site. Background, construction, and post-construction PM 2.5 and PM 10 (PM with aerodynamic diameters construction through a wind-shielding effect. The results show that the (1) confidence intervals of the mean PM concentrations during construction overlap with or are lower than background concentrations for three of the four BAM stations; and (2) post-construction PM 2.5 and PM 10 concentrations downwind of the PV installation are significantly lower than the background concentrations at three of the four BAM stations. At the fourth BAM station, downwind post-construction PM 2.5 and PM 10 concentrations increased marginally by 5.7% and 2.6% of the 24-hr ambient air quality standards defined by the U.S. Environmental Protection Agency, respectively, when compared with background concentrations, with the PM 2.5 increase being statistically insignificant. This increase may be due to vehicular emissions from an access road near the southwest corner of the site or a drainage berm near the south station. The findings demonstrate the overall environmental benefit of downwind PM emission abatement from a utility-scale PV installation in desert conditions due to wind shielding. With PM emission reductions observed within 10 months of completion of construction, post-construction monitoring of downwind PM levels may be reduced to a 1-yr period for other projects with similar soil and weather conditions. This study is the first to analyze impact of a utility photovoltaic (PV) project on downwind particulate matter (PM) concentration in desert conditions. The PM

Wind turbine cost of electricity and capacity factor

International Nuclear Information System (INIS)

Cavallo, A.J.

1995-01-01

Wind turbines are currently designed to minimize the cost of electricity at the wind turbine (the busbar cost) in a given wind regime, ignoring constraints on the capacitor factor (the ratio of the average power output to the maximum power output). The trade-off between these two quantities can be examined in a straightforward fashion; it is found that the capacitor factor can be increased by a factor of 1.3 above its value at the cost minimum for a 10 percent increase in the cost of electricity. This has important implications for the large scale integration of wind electricity on utility grids where the cost of transmission and storage may be a significant fraction of the cost of delivered electricity. (Author)

Research on a Small Signal Stability Region Boundary Model of the Interconnected Power System with Large-Scale Wind Power

Directory of Open Access Journals (Sweden)

Wenying Liu

2015-03-01

Full Text Available For the interconnected power system with large-scale wind power, the problem of the small signal stability has become the bottleneck of restricting the sending-out of wind power as well as the security and stability of the whole power system. Around this issue, this paper establishes a small signal stability region boundary model of the interconnected power system with large-scale wind power based on catastrophe theory, providing a new method for analyzing the small signal stability. Firstly, we analyzed the typical characteristics and the mathematic model of the interconnected power system with wind power and pointed out that conventional methods can’t directly identify the topological properties of small signal stability region boundaries. For this problem, adopting catastrophe theory, we established a small signal stability region boundary model of the interconnected power system with large-scale wind power in two-dimensional power injection space and extended it to multiple dimensions to obtain the boundary model in multidimensional power injection space. Thirdly, we analyzed qualitatively the topological property’s changes of the small signal stability region boundary caused by large-scale wind power integration. Finally, we built simulation models by DIgSILENT/PowerFactory software and the final simulation results verified the correctness and effectiveness of the proposed model.

Meso- and Micro-scale Modelling in China: Wind atlas analysis for 12 meteorological stations in NE China (Dongbei)

DEFF Research Database (Denmark)

Mortensen, Niels Gylling; Yang, Z.; Hansen, Jens Carsten

As part of the “Meso-Scale and Micro-Scale Modelling in China” project, also known as the CMA component of the Sino-Danish Wind Energy Development Programme (WED), microscale modelling and analyses have been carried out for 12 meteorological stations in NE China. Wind speed and direction data from...... the twelve 70-m masts have been analysed using the Wind Atlas Analysis and Application Program (WAsP 10). The wind-climatological inputs are the observed wind climates derived from the WAsP Climate Analyst. Topographical inputs are elevation maps constructed from SRTM 3 data and roughness length maps...... constructed from Google Earth satellite imagery. The maps have been compared to Chinese topographical maps and adjusted accordingly. Summaries are given of the data measured at the 12 masts for the reference period 2009. The main result of the microscale modelling is an observational wind atlas for NE China...

Revisiting the 'Buy versus Build' decision for publicly owned utilities in California considering wind and geothermal resources; TOPICAL

International Nuclear Information System (INIS)

Bolinger, Mark; Wiser, Ryan; Golove, William

2001-01-01

owned utility's decision to buy or build new renewable energy capacity-specifically wind or geothermal power-in California. To examine the economic aspects of this decision, we modified and updated a 20-year financial cash-flow model to assess the levelized cost of electricity under four supply options: (1) public utility ownership of new geothermal capacity, (2) public utility ownership of new wind capacity, (3) a PPA for new geothermal capacity, and (4) a PPA for new wind capacity

A fiber-optic ice detection system for large-scale wind turbine blades

Science.gov (United States)

Kim, Dae-gil; Sampath, Umesh; Kim, Hyunjin; Song, Minho

2017-09-01

Icing causes substantial problems in the integrity of large-scale wind turbines. In this work, a fiber-optic sensor system for detection of icing with an arrayed waveguide grating is presented. The sensor system detects Fresnel reflections from the ends of the fibers. The transition in Fresnel reflection due to icing gives peculiar intensity variations, which categorizes the ice, the water, and the air medium on the wind turbine blades. From the experimental results, with the proposed sensor system, the formation of icing conditions and thickness of ice were identified successfully in real time.

The Development and Utilization of Wind Energy in Caofeidian Harbor%曹妃甸港口风能的开发与利用

Institute of Scientific and Technical Information of China (English)

申英霞; 贺静; 高瑞香; 丁怀青

2014-01-01

风能是我国未来开发、利用的重要能源之一，本文充分研究了曹妃甸风能资源，并对曹妃甸风能资源进行分析、评估。根据该地区天然风能资源特点设计风能发电系统，实现曹妃甸港口的风能资源的开发与利用。%Wind energy is one of the important energy for the development and utilization of China energy in the future. This thesis studied the wind energy resources in Caofeidian harbor, analyzes and estimates the wind energy resource. According to the natural wind resource characteristics of the area, the authors design the wind power generating system, realize the development and utilization of wind energy resources in Caofeidian harbor.

Multi-scale analysis of compressible fluctuations in the solar wind

Energy Technology Data Exchange (ETDEWEB)

Roberts, Owen W.; Escoubet, C. Philippe [ESA/ESTEC SCI-S, Noordwijk (Netherlands); Narita, Yasuhito [Austrian Academy of Sciences, Graz (Austria). Space Research Inst.

2018-04-01

Compressible plasma turbulence is investigated in the fast solar wind at proton kinetic scales by the combined use of electron density and magnetic field measurements. Both the scale-dependent cross-correlation (CC) and the reduced magnetic helicity (σ{sub m}) are used in tandem to determine the properties of the compressible fluctuations at proton kinetic scales. At inertial scales the turbulence is hypothesised to contain a mixture of Alfvenic and slow waves, characterised by weak magnetic helicity and anti-correlation between magnetic field strength B and electron density n{sub e}. At proton kinetic scales the observations suggest that the fluctuations have stronger positive magnetic helicities as well as strong anti-correlations within the frequency range studied. These results are interpreted as being characteristic of either counter-propagating kinetic Alfven wave packets or a mixture of anti-sunward kinetic Alfven waves along with a component of kinetic slow waves.

Deployment of Wind Turbines in the Built Environment: Risks, Lessons, and Recommended Practices

Energy Technology Data Exchange (ETDEWEB)

Fields, Jason [National Renewable Energy Lab. (NREL), Golden, CO (United States); Oteri, Frank [National Renewable Energy Lab. (NREL), Golden, CO (United States); Preus, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States); Baring-Gould, Ian [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-06-01

Built-environment wind turbine (BEWT) projects are wind energy projects that are constructed on, in, or near buildings. These projects present an opportunity for distributed, low-carbon generation combined with highly visible statements on sustainability, but the BEWT niche of the wind industry is still developing and is relatively less mature than the utility-scale wind or traditional distributed wind sectors. The findings from this report cannot be extended to wind energy deployments in general because of the large difference in application and technology maturity. This paper investigates the current state of the BEWT industry by reviewing available literature on BEWT projects as well as interviewing project owners on their experiences deploying and operating the technology. The authors generated a series of case studies that outline the pertinent project details, project outcomes, and lessons learned. This paper integrates those information sources into recommended practices that can be utilized by future stakeholders to evaluate the feasibility of BEWTs for their unique applications and sites.

Impacts of large-scale offshore wind farm integration on power systems through VSC-HVDC

DEFF Research Database (Denmark)

Liu, Hongzhi; Chen, Zhe

2013-01-01

The potential of offshore wind energy has been commonly recognized and explored globally. Many countries have implemented and planned offshore wind farms to meet their increasing electricity demands and public environmental appeals, especially in Europe. With relatively less space limitation......, an offshore wind farm could have a capacity rating to hundreds of MWs or even GWs that is large enough to compete with conventional power plants. Thus the impacts of a large offshore wind farm on power system operation and security should be thoroughly studied and understood. This paper investigates...... the impacts of integrating a large-scale offshore wind farm into the transmission system of a power grid through VSC-HVDC connection. The concerns are focused on steady-state voltage stability, dynamic voltage stability and transient angle stability. Simulation results based on an exemplary power system...

European wind integration study (EWIS). Towards a successful integration of large scale wind power into European electricity grids. Final report

Energy Technology Data Exchange (ETDEWEB)

Winter, W.

2010-03-15

Large capacities of wind generators have already been installed and are operating in Germany (26GW) and Spain (16GW). Installations which are as significant in terms of proportion to system size are also established in Denmark (3.3GW), the All Island Power System of Ireland and Northern Ireland (1.5GW), and Portugal (3.4GW). Many other countries expect significant growth in wind generation such that the total currently installed capacity in Europe of 68GW is expected to at least double by 2015. Yet further increases can be expected in order to achieve Europe's 2020 targets for renewable energy. The scale of this development poses big challenges for wind generation developers in terms of obtaining suitable sites, delivering large construction projects, and financing the associated investments from their operations. Such developments also impact the networks and it was to address the immediate transmission related challenges that the European Wind Integration Study (EWIS) was initiated by Transmission System Operators (TSOs) with the objective of ensuring the most effective integration of large scale wind generation into Europe's transmission networks and electricity system. The challenges anticipated and addressed include: 1) How to efficiently accommodate wind generation when markets and transmission access arrangements have evolved for the needs of traditional controllable generation. 2) How to ensure supplies remain secure as wind varies (establishing the required backup/reserves for low wind days and wind forecast errors as well as managing network congestion in windy conditions). 3) How to maintain the quality and reliability of supplies given the new generation characteristics. 4) How to achieve efficient network costs by suitable design and operation of network connections, the deeper infrastructure including offshore connections, and crossborder interconnections. EWIS has focused on the immediate network related challenges by analysing detailed

Deployment of Wind Turbines in the Built Environment: Risks, Lessons, and Recommended Practices

Energy Technology Data Exchange (ETDEWEB)

Baring-Gould, Ian; Fields, Jason; Oteri, Frank; Preus, Robert

2017-05-31

Built-environment wind turbine (BEWT) projects are wind energy projects that are constructed on, in, or near buildings, as shown below. These projects present an opportunity for distributed, low-carbon generation combined with highly visible statements on sustainability, but the BEWT niche of the wind industry is still developing and is relatively less mature than the utility-scale wind or conventional ground-based distributed wind sectors. This poster investigates the current state of the BEWT industry by reviewing available literature on BEWT projects as well as interviewing project owners on their experiences deploying and operating the technology.

Effects of torsional degree of freedom, geometric nonlinearity, and gravity on aeroelastic behavior of large-scale horizontal axis wind turbine blades under varying wind speed conditions

DEFF Research Database (Denmark)

Jeong, Min-Soo; Cha, Myung-Chan; Kim, Sang-Woo

2014-01-01

Modern horizontal axis wind turbine blades are long, slender, and flexible structures that can undergo considerable deformation, leading to blade failures (e.g., blade-tower collision). For this reason, it is important to estimate blade behaviors accurately when designing large-scale wind turbine...

Impact of wind on the spatial distribution of rain over micro-scale topography : numerical modelling and experimental verification

NARCIS (Netherlands)

Blocken, B.J.E.; Poesen, J.; Carmeliet, J.

2006-01-01

The wind-driven-rain effect refers to the redistribution of rainfall over micro-scale topography due to the existence of local perturbed wind-flow patterns. Rainfall measurements reported in the literature point to the fact that the wind-driven-rain distribution can show large variations over

Wind around the world

International Nuclear Information System (INIS)

Rackstraw, K.

1998-01-01

A combination of cost reductions and progressive policies in key markets kept the world wind market percolating in 1997 with a record 1510 MW of new wind capacity installed, representing annual sales of more than $1.5 billion. This new record surpasses last year''s total by 24 percent, about the average annual rate of growth for the last three years. Worldwide utility-scale wind installations at the end of 1997 totaled 7763 MW. Most activity occurred in Europe, which accounted for over 75 percent of 1997 installations. Germany was again the world''s leading single market, this time by quite a large margin, accounting for more than one-third of the annual total by itself at 532 MW in 1997. The end of 1997 also marked the time at which Germany officially passed the US as the largest total single market with over 2079 MW in total installations versus about 1805 MW for the US, although the US had actually lost the lead by mid-year. Spain is the new addition to the top echelon of world wind markets, installing 215 MW in 1997 that more than doubles their total installed capacity over the previous year and ranks them number three in the world for the year. Denmark''s 1997 total of 300 MW is also a record, although this estimate could go up as the official count is finalized. India, the second largest wind market in 1995 and 1996, slipped several notches because of a variety of factors, including a change in government and a slowdown in the economy. The US wind market continues to stagnate as it has for the last several years, largely because of the uncertainty surrounding restructuring of US electric utilities. The US market is poised for a big comeback in 1998, however

Reference Manual for the System Advisor Model's Wind Power Performance Model

Energy Technology Data Exchange (ETDEWEB)

Freeman, J.; Jorgenson, J.; Gilman, P.; Ferguson, T.

2014-08-01

This manual describes the National Renewable Energy Laboratory's System Advisor Model (SAM) wind power performance model. The model calculates the hourly electrical output of a single wind turbine or of a wind farm. The wind power performance model requires information about the wind resource, wind turbine specifications, wind farm layout (if applicable), and costs. In SAM, the performance model can be coupled to one of the financial models to calculate economic metrics for residential, commercial, or utility-scale wind projects. This manual describes the algorithms used by the wind power performance model, which is available in the SAM user interface and as part of the SAM Simulation Core (SSC) library, and is intended to supplement the user documentation that comes with the software.

Experimental study of the impact of large-scale wind farms on land–atmosphere exchanges

International Nuclear Information System (INIS)

Zhang Wei; Markfort, Corey D; Porté-Agel, Fernando

2013-01-01

Large-scale wind farms, covering a significant portion of the land and ocean surface, may affect the transport of momentum, heat, mass and moisture between the atmosphere and the land locally and globally. To understand the wind-farm–atmosphere interaction, we conducted wind-tunnel experiments to study the surface scalar (heat) flux using model wind farms, consisting of more than ten rows of wind turbines—having typical streamwise and spanwise spacings of five and four rotor diameters—in a neutral boundary layer with a heated surface. The spatial distribution of the surface heat flux was mapped with an array of surface heat flux sensors within the quasi-developed regime of the wind-farm flow. Although the overall surface heat flux change produced by the wind farms was found to be small, with a net reduction of 4% for a staggered wind farm and nearly zero change for an aligned wind farm, the highly heterogeneous spatial distribution of the surface heat flux, dependent on the wind-farm layout, was significant. The difference between the minimum and maximum surface heat fluxes could be up to 12% and 7% in aligned and staggered wind farms, respectively. This finding is important for planning intensive agriculture practice and optimizing farm land use strategy regarding wind energy project development. The well-controlled wind-tunnel experiments presented in this study also provide a first comprehensive dataset on turbulent flow and scalar transport in wind farms, which can be further used to develop and validate new parameterizations of surface scalar fluxes in numerical models. (letter)

Global wind energy outlook 2006

International Nuclear Information System (INIS)

2006-09-01

The global market for wind power has been expanding faster than any other source of renewable energy. From just 4,800 MW in 1995 the world total has multiplied more than twelve-fold to reach over 59,000 MW at the end of 2005. The international market is expected to have an annual turnover in 2006 of more than euro 13 billion, with an estimated 150,000 people employed around the world. The success of the industry has attracted investors from the mainstream finance and traditional energy sectors. In a number of countries the proportion of electricity generated by wind power is now challenging conventional fuels. The Global Wind Energy Outlook 2006 reports that over a third of the world's electricity - crucially including that required by industry - can realistically be supplied by wind energy by the middle of the century. The report provides an industry blueprint that explains how wind power could supply 34% of the world's electricity by 2050. Most importantly, it concludes that if wind turbine capacity implemented on this scale it would save 113 billion tonnes of CO2 from entering the atmosphere by 2050. This places wind power as one of the world's most important energy sources for the 21st century. The 'Global Wind Energy Outlook 2006' runs three different scenarios for wind power - a Reference scenario based on figures from the International Energy Agency (IEA); a Moderate version which assumes that current targets for renewable energy are successful; and an advanced version assuming that all policy options in favour of renewables have been adopted. These are then set against two scenarios for global energy demand. Under the Reference scenario, growth in demand is again based on IEA projections; under the High Energy Efficiency version, a range of energy efficiency measures result in a substantial reduction in demand

Modelling and Analysis of Radial Flux Surface Mounted Direct-Driven PMSG in Small Scale Wind Turbine

Directory of Open Access Journals (Sweden)

Theint Zar Htet

2017-11-01

Full Text Available This paper presents the modelling and analysis of permanent magnet synchronous generator (PMSG which are used in direct driven small scale wind turbines. The 3 kW PM generator which is driven directly without gear system is analyzed by Ansoft Maxwell 2D RMxprt. The performance analysis of generator includes the cogging torque in two teeth, induced coil voltages under load, winding current under load, airgap flux density distribution and so on. The modelling analysis is based on the 2D finite element techniques. In an electrical machine, an accurate determination of the geometry parameters is a vital role. The proper performance results of 3kW PMSG in small scale wind turbine can be seen in this paper.

Gyrokinetic Simulations of Solar Wind Turbulence from Ion to Electron Scales

International Nuclear Information System (INIS)

Howes, G. G.; TenBarge, J. M.; Dorland, W.; Numata, R.; Quataert, E.; Schekochihin, A. A.; Tatsuno, T.

2011-01-01

A three-dimensional, nonlinear gyrokinetic simulation of plasma turbulence resolving scales from the ion to electron gyroradius with a realistic mass ratio is presented, where all damping is provided by resolved physical mechanisms. The resulting energy spectra are quantitatively consistent with a magnetic power spectrum scaling of k -2.8 as observed in in situ spacecraft measurements of the 'dissipation range' of solar wind turbulence. Despite the strongly nonlinear nature of the turbulence, the linear kinetic Alfven wave mode quantitatively describes the polarization of the turbulent fluctuations. The collisional ion heating is measured at subion-Larmor radius scales, which provides evidence of the ion entropy cascade in an electromagnetic turbulence simulation.

Multi-scale analysis of compressible fluctuations in the solar wind

Science.gov (United States)

Roberts, Owen W.; Narita, Yasuhito; Escoubet, C.-Philippe

2018-01-01

Compressible plasma turbulence is investigated in the fast solar wind at proton kinetic scales by the combined use of electron density and magnetic field measurements. Both the scale-dependent cross-correlation (CC) and the reduced magnetic helicity (σm) are used in tandem to determine the properties of the compressible fluctuations at proton kinetic scales. At inertial scales the turbulence is hypothesised to contain a mixture of Alfvénic and slow waves, characterised by weak magnetic helicity and anti-correlation between magnetic field strength B and electron density ne. At proton kinetic scales the observations suggest that the fluctuations have stronger positive magnetic helicities as well as strong anti-correlations within the frequency range studied. These results are interpreted as being characteristic of either counter-propagating kinetic Alfvén wave packets or a mixture of anti-sunward kinetic Alfvén waves along with a component of kinetic slow waves.

State of the Art and Trends in Wind Resource Assessment

Directory of Open Access Journals (Sweden)

Oliver Probst

2010-06-01

Full Text Available Given the significant rise of the utilization of wind energy the accurate assessment of the wind potential is becoming increasingly important. Direct applications of wind assessment techniques include the creation of wind maps on a local scale (typically 5 20 km and the micrositing of wind turbines, the estimation of vertical wind speed variations, prospecting on a regional scale (>100 km, estimation of the long-term wind resource at a given site, and forecasting. The measurement of wind speed and direction still widely relies on cup anemometers, though sonic anemometers are becoming increasingly popular. Moreover, remote sensing by Doppler techniques using the backscattering of either sonic beams (SODAR or light (LIDAR allowing for vertical profiling well beyond hub height are quickly moving into the mainstream. Local wind maps are based on the predicted modification of the regional wind flow pattern by the local atmospheric boundary layer which in turn depends on both topographic and roughness features and the measured wind rose obtained from one or several measurement towers within the boundaries of the planned development site. Initial models were based on linearized versions of the Navier-Stokes equations, whereas more recently full CFD models have been applied to wind farm micrositing. Linear models tend to perform well for terrain slopes lower than about 25% and have the advantage of short execution times. Long-term performance is frequently estimated from correlations with nearby reference stations with concurrent information and continuous time series over a period of at least 10 years. Simple methods consider only point-to-point linear correlations; more advanced methods like multiple regression techniques and methods based on the theory of distributions will be discussed. Both for early prospecting in regions where only scarce or unreliable reference information is available, wind flow modeling on a larger scale (mesoscale is becoming

Utility of an abbreviated version of the stanford-binet intelligence scales (5th ed.) in estimating 'full scale' IQ for young children with autism spectrum disorder.

Science.gov (United States)

Twomey, Conal; O'Connell, Helen; Lillis, Mary; Tarpey, Sarah Louise; O'Reilly, Gary

2018-03-01

The fifth edition of the Stanford-Binet Intelligence scales allows 'full scale' IQ (FSIQ) to be estimated using an abridged version of the test-the abbreviated battery IQ (ABIQ). Set within a public early intervention team service, the current cross-sectional study investigated the utility of the ABIQ in estimating FSIQ for 40 children with autism spectrum disorder (ASD) aged 3-5 years. A strong ABIQ-FSIQ association was yielded (r = 0.89; r 2  = 0.808) and the ABIQ did not over-estimate mean FSIQ above a clinically-relevant threshold; however, clinically significant over-estimation occurred in 17.5% of individual cases. While the findings provide support for the utility of the ABIQ in estimating FSIQ for young children with ASD, caution relating to the over-estimation of FSIQ is warranted. Careful clinical judgment-ideally based on examination of previous cognitive assessment results (if available), thorough interactional observations, and close multi-disciplinary consultation-is necessary to determine the applicability of the ABIQ to individual cases. Autism Res 2018, 11: 503-508. © 2017 International Society for Autism Research, Wiley Periodicals, Inc. We investigated the utility of a shortened version of the Stanford-Binet Intelligence Scales in estimating IQ for 40 young children with autism spectrum disorder (ASD). The findings provide qualified support for the instrument: acceptably accurate IQ estimation was achieved for most cases; but not so for a sizeable minority (17.5%). Careful clinical judgment is necessary to determine the applicability of the ABIQ to individual cases. © 2017 International Society for Autism Research, Wiley Periodicals, Inc.

Magnetic Reconnection May Control the Ion-scale Spectral Break of Solar Wind Turbulence

Science.gov (United States)

Vech, Daniel; Mallet, Alfred; Klein, Kristopher G.; Kasper, Justin C.

2018-03-01

The power spectral density of magnetic fluctuations in the solar wind exhibits several power-law-like frequency ranges with a well-defined break between approximately 0.1 and 1 Hz in the spacecraft frame. The exact dependence of this break scale on solar wind parameters has been extensively studied but is not yet fully understood. Recent studies have suggested that reconnection may induce a break in the spectrum at a “disruption scale” {λ }{{D}}, which may be larger than the fundamental ion kinetic scales, producing an unusually steep spectrum just below the break. We present a statistical investigation of the dependence of the break scale on the proton gyroradius ρ i , ion inertial length d i , ion sound radius ρ s , proton–cyclotron resonance scale ρ c , and disruption scale {λ }{{D}} as a function of {β }\\perp i. We find that the steepest spectral indices of the dissipation range occur when β e is in the range of 0.1–1 and the break scale is only slightly larger than the ion sound scale (a situation occurring 41% of the time at 1 au), in qualitative agreement with the reconnection model. In this range, the break scale shows a remarkably good correlation with {λ }{{D}}. Our findings suggest that, at least at low β e , reconnection may play an important role in the development of the dissipation range turbulent cascade and cause unusually steep (steeper than ‑3) spectral indices.

Wind Turbine Contingency Control Through Generator De-Rating

Science.gov (United States)

Frost, Susan; Goebel, Kai; Balas, Mark

2013-01-01

Maximizing turbine up-time and reducing maintenance costs are key technology drivers for wind turbine operators. Components within wind turbines are subject to considerable stresses due to unpredictable environmental conditions resulting from rapidly changing local dynamics. In that context, systems health management has the aim to assess the state-of-health of components within a wind turbine, to estimate remaining life, and to aid in autonomous decision-making to minimize damage to the turbine. Advanced contingency control is one way to enable autonomous decision-making by providing the mechanism to enable safe and efficient turbine operation. The work reported herein explores the integration of condition monitoring of wind turbines with contingency control to balance the trade-offs between maintaining system health and energy capture. The contingency control involves de-rating the generator operating point to achieve reduced loads on the wind turbine. Results are demonstrated using a high fidelity simulator of a utility-scale wind turbine.

Technology Roadmaps: How2Guide for Wind Energy Roadmap

Energy Technology Data Exchange (ETDEWEB)

NONE

2014-03-01

Whether in OECD, emerging or developing country economies, governments are increasingly looking to diversify their energy mix beyond simply fossil fuels. While wind energy is developing towards a mainstream, competitive and reliable technology, a range of barriers can delay progress, such as financing, grid integration, social acceptance and aspects of planning processes. National and regional technology roadmaps can play a key role in supporting wind energy development and implementation, helping countries to identify priorities and pathways tailored to local resources and markets. Recognising this, the IEA has started the How2Guides - a new series co-ordinated by the International Low-Carbon Energy Technology Platform to address the need for more focused guidance in the development of national roadmaps, or strategies, for specific low-carbon technologies. This builds on the success of the IEA global technology roadmap series and responds to a growing number of requests for IEA guidance to adapt the findings of the IEA global technology roadmaps to national circumstances. A successful roadmap contains a clear statement of the desired outcome, followed by a specific pathway for reaching it. The How2Guide for Wind Energy builds on the IEA well established methodology for roadmap development and shares wind specific recommendations on how to address the four phases to developing and implementing a wind energy roadmap: Planning; Visioning; Development; and Implementation. The manual also offers menus of recommendations on policy and technical options for deployment of utility-scale wind energy installations. A matrix of barriers-versus-realistic solutions options is cross-listed with considerations such as planning, development, electricity market and system, infrastructure, and finance and economics. Drawing on several case studies from around the globe, as well as on the IEA Technology Roadmap for Wind Energy, the How2Guide for Wind Energy it is intended as a

Assessing high wind energy penetration

International Nuclear Information System (INIS)

Tande, J.O.

1995-01-01

In order to convincingly promote installing wind power capacity as a substantial part of the energy supply system, a set of careful analyses must be undertaken. This paper applies a case study concentrated on assessing the cost/benefit of high wind energy penetration. The case study considers expanding the grid connected wind power capacity in Praia, the capital of Cape Verde. The currently installed 1 MW of wind power is estimated to supply close to 10% of the electric energy consumption in 1996. Increasing the wind energy penetration to a higher level is considered viable as the project settings are close to ideal, including a very capable national utility company, Electra, a conventional power supply system based on imported heavy fuel and gas oil, and favourable wind conditions with an estimated annual average of 9.3 m/s at the hub height of the wind turbines. With the applied case study assumptions, simulations with WINSYS over the lifetime of the assessed wind power investment show that investments up to 4.2 MW are economically viable. The economic optimum is found at 2.4 MW reaching an internal rate of return of almost 8% p.a. This 2.4 MW of wind power would, together with the existing wind power, supply over 30% of the electric consumption in 1996. Applying the recommended practices for estimating the cost of wind energy, the life-cycle cost of this 2.4 MW investment is estimated at a 7% discount rate and a 20 year lifetime to 0.26 DKK/kW h. (Author)

2016 Cost of Wind Energy Review

Energy Technology Data Exchange (ETDEWEB)

Stehly, Tyler J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Heimiller, Donna M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Scott, George N. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-12-29

This report uses representative utility-scale projects to estimate the levelized cost of energy (LCOE) for land-based and offshore wind power plants in the United States. Data and results detailed here are derived from 2016 commissioned plants. More specifically, analysis detailed here relies on recent market data and state-of-the-art modeling capabilities to maintain an up-to-date understanding of wind energy cost trends and drivers. This report is intended to provide insight into current component-level costs as well as a basis for understanding variability in LCOE across the country. This publication represents the sixth installment of this annual report.

A Long-Period Grating Sensor for Wind Turbine Blades

DEFF Research Database (Denmark)

Glavind, Lars

This PhD project concerns the applied research for providing a novel sensor for measurements on wind turbine blades, based on Long-Period Gratings. The idea is based on the utilization of a special asymmetrical optical fibre with Long-Period Gratings for directional sensitive bend sensing...... blade material, where a suitable process and recoating material were investigated. The sensor was implemented and tested on a full scale wind turbine blade placed on a test rig. This first prototype has demonstrated the capability of the sensor for wind turbine blade monitoring, particular...... the possibility to distinguish between the flap- and edge-wise bend directions on the wind turbine blade, providing a selective sensor. The sensor has proven to be very robust and suitable for this application....

Transient stability risk assessment of power systems incorporating wind farms

DEFF Research Database (Denmark)

Miao, Lu; Fang, Jiakun; Wen, Jinyu

2013-01-01

fed induction generator has been established. Wind penetration variation and multiple stochastic factors of power systems have been considered. The process of transient stability risk assessment based on the Monte Carlo method has been described and a comprehensive risk indicator has been proposed......Large-scale wind farm integration has brought several aspects of challenges to the transient stability of power systems. This paper focuses on the research of the transient stability of power systems incorporating with wind farms by utilizing risk assessment methods. The detailed model of double....... An investigation has been conducted into an improved 10-generator 39-bus system with a wind farm incorporated to verify the validity and feasibility of the risk assessment method proposed....

Wind energy comes of age

International Nuclear Information System (INIS)

Swisher, R.

1991-01-01

This article discusses the maturation of the wind energy industry into a reliable and cost-effective utility technology. The topics discussed include the environmental impact of windfarms, the potential of wind energy, integrating wind technology into today's utility systems, and state policy decisions critical for renewable energy development

The potential of wind farms

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

Summaries of papers presented at the European wind energy conference on the potential of wind farms are presented. It is stated that in Denmark today, wind energy provides about 3% to the Danish electricity consumption and the wind power capacity is, according to Danish wind energy policy, expected to increase substantially in the years to come. A number of countries in Europe and elsewhere are making significant progress in this repect. Descriptions of performance are given in relation to some individual wind farms. The subjects covered concern surveys of national planning and policies regarding wind utilization and national and global development of wind turbine arrays. Papers also deal with utility and project planning, wind prediction and certification, wind loads and fatigue, wakes, noise and control. (AB).

The Contribution of International Large-Scale Assessments to Educational Research: Combining Individual and Institutional Data Sources

Science.gov (United States)

Strietholt, Rolf; Scherer, Ronny

2018-01-01

The present paper aims to discuss how data from international large-scale assessments (ILSAs) can be utilized and combined, even with other existing data sources, in order to monitor educational outcomes and study the effectiveness of educational systems. We consider different purposes of linking data, namely, extending outcomes measures,…

The Integration of Renewable Energy Sources into Electric Power Distribution Systems, Vol. II Utility Case Assessments

Energy Technology Data Exchange (ETDEWEB)

Zaininger, H.W.

1994-01-01

Electric utility distribution system impacts associated with the integration of renewable energy sources such as photovoltaics (PV) and wind turbines (WT) are considered in this project. The impacts are expected to vary from site to site according to the following characteristics: the local solar insolation and/or wind characteristics, renewable energy source penetration level, whether battery or other energy storage systems are applied, and local utility distribution design standards and planning practices. Small, distributed renewable energy sources are connected to the utility distribution system like other, similar kW- and MW-scale equipment and loads. Residential applications are expected to be connected to single-phase 120/240-V secondaries. Larger kW-scale applications may be connected to three+phase secondaries, and larger hundred-kW and y-scale applications, such as MW-scale windfarms, or PV plants, may be connected to electric utility primary systems via customer-owned primary and secondary collection systems. In any case, the installation of small, distributed renewable energy sources is expected to have a significant impact on local utility distribution primary and secondary system economics. Small, distributed renewable energy sources installed on utility distribution systems will also produce nonsite-specific utility generation system benefits such as energy and capacity displacement benefits, in addition to the local site-specific distribution system benefits. Although generation system benefits are not site-specific, they are utility-specific, and they vary significantly among utilities in different regions. In addition, transmission system benefits, environmental benefits and other benefits may apply. These benefits also vary significantly among utilities and regions. Seven utility case studies considering PV, WT, and battery storage were conducted to identify a range of potential renewable energy source distribution system applications. The

Large-scale introduction of wind power stations in the Swedish grid: a simulation study

Energy Technology Data Exchange (ETDEWEB)

Larsson, L

1978-08-01

This report describes a simulation study on the factors to be considered if wind power were to be introduced to the south Swedish power grid on a large scale. The simulations are based upon a heuristic power generation planning model, developed for the purpose. The heuristic technique reflects the actual running strategies of a big power company with suitable accuracy. All simulations refer to certain typical days in 1976 to which all wind data and system characteristics are related. The installed amount of wind power will not be subject to optimization. All differences between planned and real wind power generation is equalized by regulation of the hydro power. The simulations made differ according to how the installed amount of wind power is handled in the power generation planning. The simulations indicate that the power system examined could well bear an introduction of wind power up to a level of 20% of the total power installed. This result is of course valid only for the days examined and does not necessarily apply to the present day structure of the system.