Mechanical behavior of M-Wire and conventional NiTi wire used to manufacture rotary endodontic instruments.

Science.gov (United States)

Pereira, Erika S J; Gomes, Renata O; Leroy, Agnès M F; Singh, Rupinderpal; Peters, Ove A; Bahia, Maria G A; Buono, Vicente T L

2013-12-01

Comparison of physical and mechanical properties of one conventional and a new NiTi wire, which had received an additional thermomechanical treatment. Specimens of both conventional (NiTi) and the new type of wire, called M-Wire (MW), were subjected to tensile and three-point bending tests, Vickers microhardness measurements, and to rotating-bending fatigue tests at a strain-controlled level of 6%. Fracture surfaces were observed by scanning electron microscopy and the non-deformed microstructures by transmission electron microscopy. The thermomechanical treatment applied to produce the M-Wire apparently increased the tensile strength and Vickers microhardness of the material, but its apparent Young modulus was smaller than that of conventionally treated NiTi. The three-point bending tests showed a higher flexibility for MW which also exhibited a significantly higher number of cycles to failure. M-Wire presented mechanical properties that can render endodontic instruments more flexible and fatigue resistant than those made with conventionally processed NiTi wires. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Musical Instrument Classification Based on Nonlinear Recurrence Analysis and Supervised Learning

Directory of Open Access Journals (Sweden)

R.Rui

2013-04-01

Full Text Available In this paper, the phase space reconstruction of time series produced by different instruments is discussed based on the nonlinear dynamic theory. The dense ratio, a novel quantitative recurrence parameter, is proposed to describe the difference of wind instruments, stringed instruments and keyboard instruments in the phase space by analyzing the recursive property of every instrument. Furthermore, a novel supervised learning algorithm for automatic classification of individual musical instrument signals is addressed deriving from the idea of supervised non-negative matrix factorization (NMF algorithm. In our approach, the orthogonal basis matrix could be obtained without updating the matrix iteratively, which NMF is unable to do. The experimental results indicate that the accuracy of the proposed method is improved by 3% comparing with the conventional features in the individual instrument classification.

Convention on nuclear safety

International Nuclear Information System (INIS)

1994-01-01

The Convention on Nuclear Safety was adopted on 17 June 1994 by Diplomatic Conference convened by the International Atomic Energy Agency at its Headquarters from 14 to 17 June 1994. The Convention will enter into force on the ninetieth day after the date of deposit with the Depository (the Agency's Director General) of the twenty-second instrument of ratification, acceptance or approval, including the instruments of seventeen States, having each at leas one nuclear installation which has achieved criticality in a reactor core. The text of the Convention as adopted is reproduced in the Annex hereto for the information of all Member States

Pre-bent instruments used in single-port laparoscopic surgery versus conventional laparoscopic surgery: comparative study of performance in a dry lab.

Science.gov (United States)

Miernik, Arkadiusz; Schoenthaler, Martin; Lilienthal, Kerstin; Frankenschmidt, Alexander; Karcz, Wojciech Konrad; Kuesters, Simon

2012-07-01

Different types of single-incision laparoscopic surgery (SILS) have become increasingly popular. Although SILS is technically even more challenging than conventional laparoscopy, published data of first clinical series seem to demonstrate the feasibility of these approaches. Various attempts have been made to overcome restrictions due to loss of triangulation in SILS by specially designed SILS-specific instruments. This study involving novices in a dry lab compared task performances between conventional laparoscopic surgery (CLS) and single-port laparoscopic surgery (SPLS) using newly designed pre-bent instruments. In this study, 90 medical students without previous experience in laparoscopic techniques were randomly assigned to undergo one of three procedures: CLS, SPLS using two pre-bent instruments (SPLS-pp), or SPLS using one pre-bent and one straight laparoscopic instrument (SPLS-ps). In the dry lab, the participants performed four typical laparoscopic tasks of increasing difficulty. Evaluation included performance times or number of completed tasks within a given time frame. All performances were videotaped and evaluated for unsuccessful attempts and unwanted interactions of instruments. Using subjective questionnaires, the participants rated difficulties with two-dimensional vision and coordination of instruments. Task performances were significantly better in the CLS group than in either SPLS group. The SPLS-ps group showed a tendency toward better performances than the SPLS-pp group, but the difference was not significant. Video sequences and participants` questionnaires showed instrument interaction as the major problem in the single-incision surgery groups. Although SILS is feasible, as shown in clinical series published by laparoscopically experienced experts, SILS techniques are demanding due to restrictions that come with the loss of triangulation. These can be compensated only partially by currently available SILS-designed instruments. The future of

The WHO Tobacco Convention: A New Dawn in the Implementation of International Health Instrument? Comment on "The Legal Strength of International Health Instruments - What It Brings to Global Health Governance?"

Science.gov (United States)

Durojaye, Ebenezer

2017-07-05

The Tobacco Convention was adopted by the World Health Organization (WHO) in 2003. Nikogosian and Kickbusch examine the five potential impacts of the Tobacco Convention and its Protocol on public health. These include the adoption of the Convention would seem to unlock the treaty-making powers of WHO; the impact of the Convention in the global health architecture has been phenomenal globally; the Convention has facilitated the adoption of further instruments to strengthen its implementation at the national level; the Convention has led to the adoption of appropriate legal framework to combat the use of tobacco at the national level and that the impact of the Convention would seem to go beyond public health but has also led to the adoption of the Protocol to Eliminate Illicit Trade in Tobacco. However, the article by Nikogosian and Kickbusch would seem to overlook some of the challenges that may militate against the effective implementation of international law, including the Tobacco Convention, at the national level. © 2018 The Author(s); Published by Kerman University of Medical Sciences. This is an open-access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Some potentialities of instrumental implementation of quantitative phase analysis techniques for ferromagnetic materials on the basis of Moessbauer effect

International Nuclear Information System (INIS)

Danilov, G.I.; Mamikonyan, S.V.; Shlokov, G.N.

1973-01-01

In the article the results of work are presented on instrument development for quantitative phase analysis of ferromagnetic materials on the basis of using Moessbauer effect. Analysis of the defined ferromagnetic phase content in sample is carried out by spectrum band intensity of this phase, brought in paramagnetic state. Tyrical structural scheme of instrument model is presented, intended for control of degree of ferritization of ferrite compositions in the process of low temperature baking. Advantages of the proposed method and possibilities of increasing accuracy and sensitivity of particular instruments schemes are discussed. Advantages of using resonance detectors in the proposed method are shown. Sources, detectors and measurement schemes considered, allowed to use proposed quantitative phase analysis method for analysis of ferrite compositions by 40-65% of its possibilities

Important characteristics and constitutional law basis of the optional instrument for European contract law

Directory of Open Access Journals (Sweden)

Silvija Petrić

2009-01-01

Full Text Available This paper is dedicated to the analysis of the optional instrument for European contract law as one of the measures which the European Commission suggests within the framework of the initiative of European contract law. It is about the system of general rules of contract law and particular rules for those contracts which are the most important for the functioning of a unified European market. The paper analyses the reasons for suggesting such measures, the basic characteristics and purpose, possible ways of application, potential content and structure, its relation to other Acts and measures of community law, and, in particular, the possible constitutional law basis for the bringing in of such an act of Community law.

Radioisotope instruments

CERN Document Server

Cameron, J F; Silverleaf, D J

1971-01-01

International Series of Monographs in Nuclear Energy, Volume 107: Radioisotope Instruments, Part 1 focuses on the design and applications of instruments based on the radiation released by radioactive substances. The book first offers information on the physical basis of radioisotope instruments; technical and economic advantages of radioisotope instruments; and radiation hazard. The manuscript then discusses commercial radioisotope instruments, including radiation sources and detectors, computing and control units, and measuring heads. The text describes the applications of radioisotop

A labview approach to instrumentation for the TFTR bumper limiter alignment project

International Nuclear Information System (INIS)

Skelly, G.N.; Owens, D.K.

1992-01-01

This paper reports on a project recently undertaken to measure the alignment of the TFTR bumper limiter in relation to the toroidal magnetic field axis. The process involved the measurement of the toroidal magnetic field, and the positions of the tiles that make up the bumper limiter. The basis for the instrument control and data acquisition system was National Instrument's LabVIEW 2. LabVIEW is a graphical programming system for developing scientific and engineering applications on a Macintosh. For this project, a Macintosh IIci controlled the IEEE-488 GPIB programmable instruments via an interface box connected to the SCSI port of the computer. With LabVIEW, users create graphical software modules called virtual instruments instead of writing conventional text-based code. To measure the magnetic field, the control system acquired data from two nuclear magnetic resonance magnetometers while the torroidal field coils were pulsed. To measure the position of the tiles on the limiter, an instrumented mechanical arm was used inside the vessel

Pilot dynamics for instrument approach tasks: Full panel multiloop and flight director operations

Science.gov (United States)

Weir, D. H.; Mcruer, D. T.

1972-01-01

Measurements and interpretations of single and mutiloop pilot response properties during simulated instrument approach are presented. Pilot subjects flew Category 2-like ILS approaches in a fixed base DC-8 simulaton. A conventional instrument panel and controls were used, with simulated vertical gust and glide slope beam bend forcing functions. Reduced and interpreted pilot describing functions and remmant are given for pitch attitude, flight director, and multiloop (longitudinal) control tasks. The response data are correlated with simultaneously recorded eye scanning statistics, previously reported in NASA CR-1535. The resulting combined response and scanning data and their interpretations provide a basis for validating and extending the theory of manual control displays.

Development of Highly Survivable Power and Communication System for NPP Instruments under Severe Accident

Energy Technology Data Exchange (ETDEWEB)

Yoo, Seung J.; Gu, Beom W.; Nguyen, Duy T.; Choi, Bo H.; Rim, Chun T. [KAIST, Daejeon (Korea, Republic of); Lee, So I. [KHNP CRI, Daejeon (Korea, Republic of)

2014-10-15

According to the detail report from the Fukushima nuclear accident, the failure of conventional instruments is mainly due to the following reasons. 1) Insufficient backup battery capacity after the station black out (SBO) 2) The malfunction or damage of instruments due to the extremely harsh ambient condition after the severe accident 3) The cut-off of power and communication cable due to the physical shocks of hydrogen explosion after the severe accident Since the current equipment qualification (EQ) for the NPP instruments is based on the design basis accident such as loss of coolant accident (LOCA), conventional instruments, which are examined under EQ condition, cannot guarantee their normal operation during the severe accident. A 7m-long-distance wireless power transfer and a radio frequency (RF) communication were introduced with conventional wired system to increase a redundancy. A heat isolation box and a harness are adopted to provide a protection from the expected physical shocks such as missiles and drastic increase of ambient temperature and pressure. A detail design principle of the highly survivable power and communication system, which has 4 sub-systems of a DCRS wireless power transfer, a Zigbee wireless communication, a GFRP harness, and a passive type router with a fly back regulator, has been presented in this paper. Each sub-system has been designed to have a robust operation characteristic regardless of the estimated physical shocks after the severe accident.

Development of Highly Survivable Power and Communication System for NPP Instruments under Severe Accident

International Nuclear Information System (INIS)

Yoo, Seung J.; Gu, Beom W.; Nguyen, Duy T.; Choi, Bo H.; Rim, Chun T.; Lee, So I.

2014-01-01

According to the detail report from the Fukushima nuclear accident, the failure of conventional instruments is mainly due to the following reasons. 1) Insufficient backup battery capacity after the station black out (SBO) 2) The malfunction or damage of instruments due to the extremely harsh ambient condition after the severe accident 3) The cut-off of power and communication cable due to the physical shocks of hydrogen explosion after the severe accident Since the current equipment qualification (EQ) for the NPP instruments is based on the design basis accident such as loss of coolant accident (LOCA), conventional instruments, which are examined under EQ condition, cannot guarantee their normal operation during the severe accident. A 7m-long-distance wireless power transfer and a radio frequency (RF) communication were introduced with conventional wired system to increase a redundancy. A heat isolation box and a harness are adopted to provide a protection from the expected physical shocks such as missiles and drastic increase of ambient temperature and pressure. A detail design principle of the highly survivable power and communication system, which has 4 sub-systems of a DCRS wireless power transfer, a Zigbee wireless communication, a GFRP harness, and a passive type router with a fly back regulator, has been presented in this paper. Each sub-system has been designed to have a robust operation characteristic regardless of the estimated physical shocks after the severe accident

Low-Budget Instrumentation of a Conventional Leg Press to Measure Reliable Isometric-Strength Capacity.

Science.gov (United States)

Baur, Heiner; Groppa, Alessia Severina; Limacher, Regula; Radlinger, Lorenz

2016-02-02

Maximum strength and rate of force development (RFD) are 2 important strength characteristics for everyday tasks and athletic performance. Measurements of both parameters must be reliable. Expensive isokinetic devices with isometric modes are often used. The possibility of cost-effective measurements in a practical setting would facilitate quality control. The purpose of this study was to assess the reliability of measurements of maximum isometric strength (Fmax) and RFD on a conventional leg press. Sixteen subjects (23 ± 2 y, 1.68 ± 0.05 m, 59 ± 5 kg) were tested twice within 1 session. After warm-up, subjects performed 2 times 5 trials eliciting maximum voluntary isometric contractions on an instrumented leg press (1- and 2-legged randomized). Fmax (N) and RFD (N/s) were extracted from force-time curves. Reliability was determined for Fmax and RFD by calculating the intraclass correlation coefficient (ICC), the test-retest variability (TRV), and the bias and limits of agreement. Reliability measures revealed good to excellent ICCs of .80-.93. TRV showed mean differences between measurement sessions of 0.4-6.9%. The systematic error was low compared with the absolute mean values (Fmax 5-6%, RFD 1-4%). The implementation of a force transducer into a conventional leg press provides a viable procedure to assess Fmax and RFD. Both performance parameters can be assessed with good to excellent reliability allowing quality control of interventions.

From BASIS to MIRACLES

DEFF Research Database (Denmark)

Tsapatsaris, Nikolaos; Willendrup, Peter Kjær; E. Lechner, Ruep

2015-01-01

Results based on virtual instrument models for the first high-flux, high-resolution, spallation based, backscattering spectrometer, BASIS are presented in this paper. These were verified using the Monte Carlo instrument simulation packages McStas and VITESS. Excellent agreement of the neutron count...... are pivotal to the conceptual design of the next generation backscattering spectrometer, MIRACLES at the European Spallation Source....

Non-conventional applications of a noninvasive portable X-ray diffraction/fluorescence instrument

International Nuclear Information System (INIS)

Chiari, Giacomo; Sarrazin, Philippe; Heginbotham, Arlen

2016-01-01

Noninvasive techniques have become widespread in the cultural heritage analytical domain. The popular handheld X-ray fluorescence (XRF) devices give the elemental composition of all the layers that X-rays can penetrate, but no information on how atoms are bound together or at which depth they are located. A noninvasive portable X-ray powder diffraction/X-ray fluorescence (XRD/XRF) device may offer a solution to these limitations, since it can provide information on the composition of crystalline materials. This paper introduces applications of XRD beyond simple phase recognition. The two fundamental principles for XRD are: (1) the crystallites should be randomly oriented, to ensure proper intensity to all the diffraction peaks, and (2) the material should be positioned exactly in the focal plane of the instrument, respecting its geometry, as any displacement of the sample would results in 2θ shifts of the diffraction peaks. In conventional XRD, the sample is ground and set on the properly positioned sample holder. Using a noninvasive portable instrument, these two requirements are seldom fulfilled. The position, size and orientation of a given crystallite within a layered structure depend on the object itself. Equation correlating the displacement (distance from the focal plane) versus peak shift (angular difference in 2θ from the standard value) is derived and used to determine the depth at which a given substance is located. The quantitative composition of two binary Cu/Zn alloys, simultaneously present, was determined measuring the cell volume and using Vegard's law. The analysis of the whole object gives information on the texture and possible preferred orientations of the crystallites, which influences the peak intensity. This allows for the distinction between clad and electroplated daguerreotypes in the case of silver and between ancient and modern gilding for gold. Analyses of cross sections can be carried out successfully. Finally, beeswax, used in Roman

Instrumental Variables in the Long Run

DEFF Research Database (Denmark)

Casey, Gregory; Klemp, Marc Patrick Brag

2017-01-01

In the study of long-run economic growth, it is common to use historical or geographical variables as instruments for contemporary endogenous regressors. We study the interpretation of these conventional instrumental variable (IV) regressions in a general, yet simple, framework. Our aim...... quantitative implications for the field of long-run economic growth. We also use our framework to examine related empirical techniques. We find that two prominent regression methodologies - using gravity-based instruments for trade and including ancestry-adjusted variables in linear regression models - have...... is to estimate the long-run causal effect of changes in the endogenous explanatory variable. We find that conventional IV regressions generally cannot recover this parameter of interest. To estimate this parameter, therefore, we develop an augmented IV estimator that combines the conventional regression...

Preliminary assessment on the differences of nuclear terrorism convention from the convention on the physical protection of nuclear material and amendment to the convention on the physical protection of nuclear material

International Nuclear Information System (INIS)

Midiana Ariethia; Muhamad Ilman A A; Mas Pungky Hendrawijaya

2011-01-01

The threat of acts of nuclear terrorism in all its forms and manifestations create the urgent need to enhance international cooperation between countries in designing and following practical and effective measures for the prevention of acts of terrorism and to counter and punish its offenders. Several United Nations Security Council Resolutions, such as UNSCR Number 1373 (2001), and UNSCR Number 1540 (2005), and the result of Nuclear Security Summit in 2010 that encourage the member countries of IAEA to ratify nuclear conventions as soon as possible, are the reasons that the Indonesian Government planning on ratifying The International Convention for The Suppression of Acts of Nuclear Terrorism (Nuclear Terrorism Convention). Nuclear Terrorism Convention is one of the 16 (sixteen) international instruments that must be ratified by the member countries of IAEA. Of the 16 (sixteen) international instruments, 3 (three) conventions are related to nuclear; Convention on the Physical Protection of Nuclear Material, Amendment to the Convention on the Physical Protection of Nuclear Material, dan Nuclear Terrorism Convention. This paper presents the preliminary assessment on the differences of Nuclear Terrorism Convention to The Convention on The Physical Protection of Nuclear Material and Amendment to The Convention on The Physical Protection of Nuclear Material. This assessment is important due to the plan of the Indonesian Government to ratify the Nuclear Terrorism Convention. The result of this assessment could be used by BAPETEN in the ratification process of the Nuclear Terrorism Convention. The method used in this assessment is references assessment. (author)

Mechanical and Metallurgical Properties of Various Nickel-Titanium Rotary Instruments

Directory of Open Access Journals (Sweden)

Kyu-Sang Shim

2017-01-01

Full Text Available The aim of this study was to investigate the effect of thermomechanical treatment on mechanical and metallurgical properties of nickel-titanium (NiTi rotary instruments. Eight kinds of NiTi rotary instruments with sizes of ISO #25 were selected: ProFile, K3, and One Shape for the conventional alloy; ProTaper NEXT, Reciproc, and WaveOne for the M-wire alloy; HyFlex CM for the controlled memory- (CM- wire; and TF for the R-phase alloy. Torsional fracture and cyclic fatigue fracture tests were performed. Products underwent a differential scanning calorimetry (DSC analysis. The CM-wire and R-phase groups had the lowest elastic modulus, followed by the M-wire group. The maximum torque of the M-wire instrument was comparable to that of a conventional instrument, while those of the CM-wire and R-phase instruments were lower. The angular displacement at failure (ADF for the CM-wire and R-phase instruments was higher than that of conventional instruments, and ADF of the M-wire instruments was lower. The cyclic fatigue resistance of the thermomechanically treated NiTi instruments was higher. DSC plots revealed that NiTi instruments made with the conventional alloy were primarily composed of austenite at room temperature; stable martensite and R-phase were found in thermomechanically treated instruments.

Paris convention - Decisions, recommendations, interpretations

International Nuclear Information System (INIS)

1990-01-01

This booklet is published in a single edition in English and French. It contains decisions, recommendations and interpretations concerning the 1960 Paris Convention on Third Party Liability in the Field of Nuclear Energy adopted by the OECD Steering Committee and the OECD Council. All the instruments are set out according to the Article of the Convention to which they relate and explanatory notes are added where necessary [fr

The Convention on the Recognition and Enforcement of Foreign ...

African Journals Online (AJOL)

The Convention on the Recognition and Enforcement of Foreign Arbitral Awards, often referred to as the New York Convention, has established itself as a regulatory and enforcement instrument which is crucial to international trade. This is evident from the fact that more than 150 countries have so far ratified the convention.

Survey and analysis on environmental and electromagnetic effect on instrumentation and control equipment of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Hwang, In Koo; Lee, Dong Young; Cha, Kyung Ho

2001-03-01

As the instrumentation and control (I and C) equipment suppliers tend to provide digital components rather than conventional analog type components for instrumentation and control systems of nuclear power plants(NPPs), it is unavoidable to adopt digital equipment for safety I and C systems as well as non-safety systems. However, the full introduction of digital equipment for I and C systems of nuclear power plants raises several concerns which have not been considered in conventional analog I and C equipment. The two major examples of the issues of digital systems are environmental/electromagnetic compatibility (EMC) and software reliability. This report presents the survey and research results on environmental and electromagnetic effect on I and C equipment of nuclear power plants to give a guideline for aging management and design process. Electromagnetic site surveys were conducted to be used as a part of technical basis to demonstrate that I and C systems are compatible with the ambient electromagnetic noise in Korean nuclear power plants.

Possible new basis for fast reactor subassembly instrumentation

Energy Technology Data Exchange (ETDEWEB)

Edwards, A G

1977-03-01

This is a digest of a paper presented to the Risley Engineering Society. The theme is a speculation that the core instrumentation problem for a liquid metal fast breeder reactor might be transformed by developments in the realm of infrared television and in pattern recognition by computer. There is a possible need to measure coolant flow and cooled exit temperature for each subassembly, with familiar fail-to-safety characteristics. Present methods use electrical devices, for example thermocouples, but this gives rise to cabling problems. It might be possible, however, to instal at the top of each subassembly a mechanical device that gives a direct indication of temperature and flow visible to an infrared television camera. Signal transmission by cable would then be replaced by direct observation. A possible arrangement for such a system is described and is shown in schematic form. It includes pattern recognition by computer. It may also be possible to infer coolant temperature directly from the characteristics of the infrared radiation emitted by a thin stainless steel sheet in contact with the sodium, and an arrangement for this is shown. The type of pattern produced for on-line interpretation by computer is also shown. It is thought that this new approach to the problem of subassembly instrumentation is sufficiently attractive to justify a close study of the problems involved.

Evaluation of purity with its uncertainty value in high purity lead stick by conventional and electro-gravimetric methods.

Science.gov (United States)

Singh, Nahar; Singh, Niranjan; Tripathy, S Swarupa; Soni, Daya; Singh, Khem; Gupta, Prabhat K

2013-06-26

A conventional gravimetry and electro-gravimetry study has been carried out for the precise and accurate purity determination of lead (Pb) in high purity lead stick and for preparation of reference standard. Reference materials are standards containing a known amount of an analyte and provide a reference value to determine unknown concentrations or to calibrate analytical instruments. A stock solution of approximate 2 kg has been prepared after dissolving approximate 2 g of Pb stick in 5% ultra pure nitric acid. From the stock solution five replicates of approximate 50 g have been taken for determination of purity by each method. The Pb has been determined as PbSO4 by conventional gravimetry, as PbO2 by electro gravimetry. The percentage purity of the metallic Pb was calculated accordingly from PbSO4 and PbO2. On the basis of experimental observations it has been concluded that by conventional gravimetry and electro-gravimetry the purity of Pb was found to be 99.98 ± 0.24 and 99.97 ± 0.27 g/100 g and on the basis of Pb purity the concentration of reference standard solutions were found to be 1000.88 ± 2.44 and 1000.81 ± 2.68 mg kg-1 respectively with 95% confidence level (k = 2). The uncertainty evaluation has also been carried out in Pb determination following EURACHEM/GUM guidelines. The final analytical results quantifying uncertainty fulfills this requirement and gives a measure of the confidence level of the concerned laboratory. Gravimetry is the most reliable technique in comparison to titremetry and instrumental method and the results of gravimetry are directly traceable to SI unit. Gravimetric analysis, if methods are followed carefully, provides for exceedingly precise analysis. In classical gravimetry the major uncertainties are due to repeatability but in electro-gravimetry several other factors also affect the final results.

Preparation of severely curved simulated root canals using engine-driven rotary and conventional hand instruments.

Science.gov (United States)

Szep, S; Gerhardt, T; Leitzbach, C; Lüder, W; Heidemann, D

2001-03-01

This in vitro study evaluated the efficacy and safety of six different nickel-titanium engine-driven instruments used with a torque-controlled engine device and nickel-titanium hand and stainless steel hand instruments in preparation of curved canals. A total of 80 curved (36 degrees) simulated root canals were prepared. Images before and after were superimposed, and instrumentation areas were observed. Time of instrumentation, instrument failure, change in working length and weight loss were also recorded. Results show that stainless steel hand instruments cause significantly less transportation towards the inner wall of the canal than do nickel-titanium hand instruments. No instrument fracture occurred with hand instruments, but 30-60% breakage of instruments was recorded during instrumentation with the engine-driven devices. The working length was maintained by all types of instruments. Newly developed nickel-titanium rotary files were not able to prevent straightening of the severely curved canals when a torque-controlled engine-driven device was used.

Comparison of the mechanical properties of rotary instruments made of conventional nickel-titanium wire, M-wire, or nickel-titanium alloy in R-phase.

Science.gov (United States)

Lopes, Hélio P; Gambarra-Soares, Thaiane; Elias, Carlos N; Siqueira, José F; Inojosa, Inês F J; Lopes, Weber S P; Vieira, Victor T L

2013-04-01

This study compared the mechanical properties of endodontic instruments made of conventional nickel-titanium (NiTi) wire (K(3) and Revo-S SU), M-Wire (ProFile Vortex), or NiTi alloy in R-phase (K(3)XF). The test instruments were subjected to mechanical tests to evaluate resistance to bending (flexibility), cyclic fatigue, and torsional load in clockwise rotation. Data were statistically evaluated by the analysis of variance test and the Student-Newman-Keuls test for multiple comparisons. In the bending resistance test, flexibility decreased in the following order: K(3)XF > Revo-S SU > ProFile Vortex > K(3). The ranking in the fatigue resistance test was the following: K(3)XF > K(3) > ProFile Vortex > Revo-S SU. In the torsional assay, the angular deflection at failure decreased in the following order: K(3)XF > Revo-S SU > K(3) > ProFile Vortex. For the maximum torque values, the ranking was K(3) > K(3)XF > ProFile Vortex > Revo-S SU. The results showed that the K(3)XF instrument, which is made of NiTi alloy in R-phase, had the overall best performance in terms of flexibility, angular deflection at failure, and cyclic fatigue resistance. In addition to the alloy from which the instrument is manufactured, the design and dimensions are important determinants of the mechanical performance of endodontic instruments. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Technical basis and evaluation criteria for an air sampling/monitoring program

International Nuclear Information System (INIS)

Gregory, D.C.; Bryan, W.L.; Falter, K.G.

1993-01-01

Air sampling and monitoring programs at DOE facilities need to be reviewed in light of revised requirements and guidance found in, for example, DOE Order 5480.6 (RadCon Manual). Accordingly, the Oak Ridge National Laboratory (ORNL) air monitoring program is being revised and placed on a sound technical basis. A draft technical basis document has been written to establish placement criteria for instruments and to guide the ''retrospective sampling or real-time monitoring'' decision. Facility evaluations are being used to document air sampling/monitoring needs, and instruments are being evaluated in light of these needs. The steps used to develop this program and the technical basis for instrument placement are described

Optimal combination of marketing instruments as a basis for tourist destination strategic management

OpenAIRE

Zupanovic, Ivo

2007-01-01

The marketing mix concept is understood as a certain combination of the instruments that form a tourist offer. Marketing mix enables integration of marketing activities, in order to satisfy the needs of tourist clients,but also in order to achieve the goals of tourist subjects business. Marketing instruments optimising is necessary during the adaptation to certain tourist segments.A suitable marketing mix is not just a simple sum of different instruments but an optimal combination of certain ...

Corticotomy-facilitated orthodontics using piezosurgery versus rotary instruments: an experimental study.

Science.gov (United States)

Farid, Karim A; Mostafa, Yehya A; Kaddah, Mohammed A; El-Sharaby, Fouad Aly

2014-10-01

The aim of this study was to evaluate corticotomy-facilitated orthodontics (CFO) using piezosurgery versus conventional rotary instruments. Ten healthy adult male mongrel dogs of comparable age with a complete set of permanent dentition with average weights between 13-17 kilograms were used. CFO using conventional rotary instruments versus piezosurgery was performed on each dog in a split mouth design. For every dog, mandibular 2nd premolar retraction on each side was attempted after extracting 3rd premolars followed by corticotomy-facilitated orthodontics using conventional rotary surgical burs on the left side and an ultrasonic piezosurgery system on the right side of the same animal. Intraoral measurements of the rate of tooth movement were taken with a sliding caliper. Measurements were performed by the same operator at the time of surgery (appliance delivery) and every month for six months. The dogs were sacrificed after six months from initiation of tooth movement to evaluate the amount of tooth movement for both conventional rotary and piezosurgery corticotomy techniques. A statistically significantly higher mean amount of tooth movement for conventional rotary instrument versus the piezosurgery corticotomy technique was observed at all time intervals. Tooth movement was 1.6 times faster when CFO was done using conventional rotary instruments as compared to a piezosurgery device.

Assessing the psychometric properties and the perceived usefulness of the BasisRaadsOnderzoek (BARO as a first-line screening instrument for juvenile offenders

Directory of Open Access Journals (Sweden)

van Loosbroek Erik

2011-06-01

Full Text Available Abstract Background The aim of this study is to investigate the psychometric properties and the perceived usefulness of the BARO (Dutch: BAsisRaadsOnderzoek; Protection Board Preliminary Examination of Juvenile Suspects. The BARO is a first-line screening instrument for the identification of psychiatric disorders, adverse environmental factors, and levels of (dysfunction in adolescent offenders (age 12 to 18, to be used by social workers of the Child Protection Board (CPB following a police arrest. Method CPB workers administered the BARO to 295 juvenile offenders (91% boys, 9% girls. A subgroup of 66 offenders (89% boys, 11% girls underwent an elaborate diagnostic assessment by forensic psychologists and psychiatrists. Using these assessments the most relevant psychometric properties of the BARO were studied. The perceived usefulness was studied using questionnaires to be filled in by the CPB social workers. Results The internal consistency of the instrument was sufficient to good, the concurrent validity of the CPB social workers applying the BARO and the forensic experts carrying out the comprehensive diagnostic assessment was strong, the discriminatory value of the instrument was moderate to strong, and the perceived usefulness of the instrument was evaluated as good to very good by the majority of the CPB workers. Discussion The BARO has sufficient to good psychometric properties including moderate to strong discriminatory value and is considered a good screening instrument by the CPB social workers. In conclusion, the BARO seems to be a very promising first-line screening instrument to identify psychiatric and psychosocial problems in young offenders.

A possible new basis for fast reactor subassembly instrumentation

International Nuclear Information System (INIS)

Edwards, A.G.

1977-01-01

This is a digest of a paper presented to the Risley Engineering Society. The theme is a speculation that the core instrumentation problem for a liquid metal fast breeder reactor might be transformed by developments in the realm of infrared television and in pattern recognition by computer. There is a possible need to measure coolant flow and cooled exit temperature for each subassembly, with familiar fail-to-safety characteristics. Present methods use electrical devices, for example thermocouples, but this gives rise to cabling problems. It might be possible, however, to instal at the top of each subassembly a mechanical device that gives a direct indication of temperature and flow visible to an infrared television camera. Signal transmission by cable would then be replaced by direct observation. A possible arrangement for such a system is described and is shown in schematic form. It includes pattern recognition by computer. It may also be possible to infer coolant temperature directly from the characteristics of the infrared radiation emitted by a thin stainless steel sheet in contact with the sodium, and an arrangement for this is shown. The type of pattern produced for on-line interpretation by computer is also shown. It is thought that this new approach to the problem of subassembly instrumentation is sufficiently attractive to justify a close study of the problems involved. (U.K.)

26 CFR 521.103 - Scope of the convention.

Science.gov (United States)

2010-04-01

... convention, to be accomplished on a reciprocal basis, are to avoid double taxation upon major items of income... looking to the avoidance of double taxation and fiscal evasion. (b) The specific classes of income from... UNDER TAX CONVENTIONS DENMARK General Income Tax Taxation of Nonresident Aliens Who Are Residents of...

Convention on early notification of a nuclear accident. Convention on assistance in the case of a nuclear accident or radiological emergency

International Nuclear Information System (INIS)

1989-08-01

The document refers to the Convention on early notification of a nuclear accident (INFCIRC-335) and to the Convention on assistance in the case of a nuclear accident or radiological emergency (INFCIRC-336). Part I contains reservations/declarations made upon or following signature and Part II contains reservations/declarations made upon or following deposit of instrument expressing consent to be bound. The status of signature, ratification, acceptance, approval or accession by States or organizations as of 31 July 1989 for the conventions is presented in two attachments

An improved instrument setpoint control program

International Nuclear Information System (INIS)

Cash, J.S. Jr.; George, R.T.; Kincaid, S.C.

1991-01-01

Instrument setpoints have a definite and often significant impact on plant safety, reliability, and availability. Although typically overshadowed by plant design, modification, and physical change activities, instrument setpoints can alter plant status and system operating characteristics just as significantly. Recognizing the need for a formal program that provides configuration control of instrument setpoints, provides a readily accessible and clearly documented basis for instrument setpoints, and integrates and coordinates operations, engineering, and maintenance activities that influence the basis for instrument setpoints, Philadelphia Electric Company (PECo) is developing an Improved Instrument Setpoint Control Program (IISCP) that incorporates current industry guidance and practices and state-of-the-art information systems technology. The IISCP was designed around PECo's then existing business processes for setpoint control, determination, and maintenance. A task force representing the various constituencies from both plants and the engineering and services organizations were formed to identify objectives and design features for the IISCP. Utilizing industry standards and guidance, regulatory documents, the experiences and good practices obtained from other utilities, and PECo's nuclear group strategies, objectives, and goals, specific objectives were identified to enhance the business processes

Grounding Damage to Conventional Vessels

DEFF Research Database (Denmark)

Lützen, Marie; Simonsen, Bo Cerup

2003-01-01

The present paper is concerned with rational design of conventional vessels with regard to bottom damage generated in grounding accidents. The aim of the work described here is to improve the design basis, primarily through analysis of new statistical data for grounding damage. The current regula...

Training With Curved Laparoscopic Instruments in Single-Port Setting Improves Performance Using Straight Instruments: A Prospective Randomized Simulation Study.

Science.gov (United States)

Lukovich, Peter; Sionov, Valery Ben; Kakucs, Timea

2016-01-01

Lately single-port surgery is becoming a widespread procedure, but it is more difficult than conventional laparoscopy owing to the lack of triangulation. Although, these operations are also possible with standard laparoscopic instruments, curved instruments are being developed. The aims of the study were to identify the effect of training on a box trainer in single-port setting on the quality of acquired skills, and transferred with the straight and curved instruments for the basic laparoscopic tasks, and highlight the importance of a special laparoscopic training curriculum. A prospective study on a box trainer in single-port setting was conducted using 2 groups. Each group performed 2 tasks on the box trainer in single-port setting. Group-S used conventional straight laparoscopic instruments, and Group-C used curved laparoscopic instruments. Learning curves were obtained by daily measurements recorded in 7-day sessions. On the last day, the 2 groups changed instruments between each other. 1st Department of Surgery, Semmelweis University of Medicine from Budapest, Hungary, a university teaching hospital. In all, 20 fifth-year medical students were randomized into 2 groups. None of them had any laparoscopic or endoscopic experience. Participation was voluntary. Although Group-S performed all tasks significantly faster than Group-C on the first day, the difference proved to be nonsignificant on the last day. All participants achieved significantly shorter task completion time on the last day than on the first day, regardless of the instrument they used. Group-S showed improvement of 63.5%, and Group-C 69.0% improvement by the end of the session. After swapping the instruments, Group-S reached significantly higher task completion time with curved instruments, whereas Group-C showed further progression of 8.9% with straight instruments. Training with curved instruments in a single-port setting allows for a better acquisition of skills in a shorter period. For this

Nuclear instrument engineering - the measuring and informative basis of nuclear science and technology

International Nuclear Information System (INIS)

Matveev, V.V.; Krasheninnikov, I.S.; Murin, I.D.; Stas', K.N.

1977-01-01

The cornerstones of developing nuclear instrument engineering in the USSR are shortly discussed. The industry is based on a well developed theory. A system approach is a characteristic feature of the present-day measuring and control systems engineering. Major functions of reactor instruments measuring different types of ionizing radiation are discussed at greater length. Nuclear measuring and control instruments and methods are widely used in different fields of science and technoloay and in different industries in the USSR. The efficient and safe operation of a nuclear facility is underlined to depend strongly upon a correlation between a technological process and the information and control system of the facility

The 1968 Brussels convention and liability for nuclear damage

International Nuclear Information System (INIS)

Sands, Ph.; Galizzi, P.

2000-01-01

The legal regime governing civil liability for transboundary nuclear damage is expressly addressed by two instruments adopted in the 1960's: the 1960 Paris Convention on Third Party Liability in the Field of Nuclear Energy and the 1963 Vienna Convention on Civil Liability for Nuclear Damage These establish particular rules governing the jurisdiction of national courts and other matters, including channelling of liability to nuclear operators, definitions of nuclear damage, the applicable standard of care, and limitations on liability. Another instrument - the 1968 Brussels Convention on Jurisdiction and the Enforcement of Judgements in Civil and Commercial Matters (hereinafter referred to as 'the Brussels Convention') - which is not often mentioned in the nuclear context will nevertheless also be applicable in certain cases. It is premised upon different rules as to forum and applicable law, and presents an alternate vision of the appropriate arrangements governing civil liability for nuclear damage. In this paper we consider the relative merits and demerits of the Brussels Convention from the perspective of non-nuclear states which might suffer damage as a result of a nuclear accident in another state. We conclude that in the context of the applicability of the Brussels Convention the dedicated nuclear liability conventions present few attractions to non-nuclear states in Europe. We focus in particular on issues relating to jurisdiction and applicable law, and do so by reference to a hypothetical accident in the United Kingdom which has transboundary effects in Ireland. (author)

Energy-efficiency instruments in the electricity area

International Nuclear Information System (INIS)

Hammer, S.; Oettli, B.; Schneider, Ch.; Iten, R.; Peherstorfer, N.

2007-06-01

This comprehensive report for the Swiss Federal Office of Energy (SFOE) describes a mix of instruments that could increase the efficiency of electricity usage in Switzerland. The basis for the development of these instruments - the experience gained in Europe in this area - is discussed. Explicitly not discussed are energy and electricity steering taxes, which could also be part of a future instrument-mix. The measures suggested include the setting of compulsory long-term reduction targets that are to form the basis for strategies and measures to be taken in particular areas and the development of an appropriate instrument-mix for this purpose. These could include regulations and labels, a national fund and certificate trading. Suppliers of electricity could be committed to increasing the efficiency of electricity use and national programmes could also attempt to influence consumer habits. The instruments should, according to the authors, be based on the existing legal framework and use know-how and structures that are already available

International instruments and information exchange on incidents falling within the ITDB scope

International Nuclear Information System (INIS)

2010-01-01

The responsibility for nuclear security rests entirely with each individual state. However,states need to work together to enhance collective nuclear security. There are international legal instruments that provide a strategic framework and a common platform for such cooperation. Among such legally binding security related instruments are: Convention on the physical protection of Nuclear materials, Convention on the early notification of nuclear accident and the International convention for the Suppression of acts of Nuclear Terrorism.

Reliability of patient specific instrumentation in total knee arthroplasty.

Science.gov (United States)

Jennart, Harold; Ngo Yamben, Marie-Ange; Kyriakidis, Theofylaktos; Zorman, David

2015-12-01

The aim of this study was to compare the precision between Patient Specific Instrumentation (PSI) and Conventional Instrumentation (CI) as determined intra-operatively by a pinless navigation system. Eighty patients were included in this prospective comparative study and they were divided into two homogeneous groups. We defined an original score from 6 to 30 points to evaluate the accuracy of the position of the cutting guides. This score is based on 6 objective criteria. The analysis indicated that PSI was not superior to conventional instrumentation in the overall score (p = 0.949). Moreover, no statistically significant difference was observed for any individual criteria of our score. Level of evidence II.

NON-CONVENTIONAL MACHINING PROCESSES SELECTION USING MULTI-OBJECTIVE OPTIMIZATION ON THE BASIS OF RATIO ANALYSIS METHOD

Directory of Open Access Journals (Sweden)

MILOŠ MADIĆ

2015-11-01

Full Text Available The role of non-conventional machining processes (NCMPs in today’s manufacturing environment has been well acknowledged. For effective utilization of the capabilities and advantages of different NCMPs, selection of the most appropriate NCMP for a given machining application requires consideration of different conflicting criteria. The right choice of the NCMP is critical to the success and competitiveness of the company. As the NCMP selection problem involves consideration of different conflicting criteria, of different relative importance, the multi-criteria decision making (MCDM methods are very useful in systematical selection of the most appropriate NCMP. This paper presents the application of a recent MCDM method, i.e., the multi-objective optimization on the basis of ratio analysis (MOORA method to solve NCMP selection which has been defined considering different performance criteria of four most widely used NCMPs. In order to determine the relative significance of considered quality criteria a pair-wise comparison matrix of the analytic hierarchy process was used. The results obtained using the MOORA method showed perfect correlation with those obtained by the technique for order preference by similarity to ideal solution (TOPSIS method which proves the applicability and potentiality of this MCDM method for solving complex NCMP selection problems.

A Finescale Lagrangian Instrument System

National Research Council Canada - National Science Library

Toole, John

2003-01-01

... from conventional, bottom-anchored moorings. An initial trial of the concept targeting the upper ocean was carried out off Bermuda in November 2001 with an instrument profiling between 12 and 28O-m depth...

The protocol amending the 1963 Vienna Convention

International Nuclear Information System (INIS)

Lamm, V.

2006-01-01

Technically the Vienna Convention was revised by the adoption of the protocol to amend the instrument. and according to Article 19 of the protocol 'A State which is Party to this Protocol but not to the 1963 Vienna Convention shall be bound by the provisions of that Convention as amended by this Protocol in relation to other States Parties hereto, and failing an expression of a different intention by that State at the time of deposit of an instrument referred to in Article 20 shall be bound by the provisions of the 1963 Vienna Convention in relation to States which are only Parties thereto'. This solution has created a special situation, because after the entry into force of the protocol there will be living together or operating in practice 'two' Vienna Conventions, notably the convention's original text of 1963 and its new version as amended by the protocol. After the protocol has come into force, a state may only accede to the amended version, but in the inter se relations of the States Party to the 'old' Vienna Convention the provisions of that convention will remain in force until such time as they have acceded to the new protocol. This rather complicated situation is nevertheless understandable and is fully in accord with Article 40 of the 1969 Vienna Convention on the Law of Treaties, which provides for the amendment of multilateral treaties. In 1989 the negotiations on the revision of the Vienna Convention had begun with the aim of strengthening the existing nuclear liability regime and of improving the situation of potential victims of nuclear accidents. The Protocol to Amend the Vienna Convention serves those purposes; it also reflects a good compromise, since it is the outcome of a negotiation process in which experts from both nuclear and non-nuclear states, from Contacting Parties and non-Contracting Parties were very active. That affords some assurance that the compromise solution reached is acceptable to all States participating in the adoption of

The Joint Convention on the safety of spent fuel management and on the safety of radioactive waste management. An instrument to achieve a global safety

International Nuclear Information System (INIS)

Risoluti, P.

2006-01-01

The Joint Convention on the Safety of Spent Fuel Management and the Safety of Radioactive Waste Management (the Joint Convention) is the first legally binding international treaty in the area of radioactive material management. It was adopted by a Diplomatic Conference in September 1997 and opened for signature on 29 September 1997. The Convention entered into force on 18 June 1998, and to date (May 2006) has been ratified by 41 countries. The Joint Convention applies to spent fuel and radioactive waste resulting from civilian application. Its principal aim is to achieve and maintain a high degree of safety in their management worldwide. The Convention is an incentive instrument, not designed to ensure fulfilment of obligations through control and sanction, but by a volunteer peer review mechanism. The obligations of the Contracting Parties are mainly based on the international safety standards developed by the IAEA in past decades. The Convention is of interest of all countries generating radioactive waste. Therefore it is relevant not only for those using nuclear power, but for any country where application of nuclear energy in education, agriculture, medicine and industry is currently used. Obligations of Contracting Parties include attending a Review Meeting held every three years and prepare National Reports for review by the other Contracting Parties. In the National Reports basic information on inventory and facilities for management of radioactive materials has to be provided. Countries with small nuclear power and/or research programs or countries having radioactive materials only from nuclear application on medicine, agriculture or conventional industry, can benefit from the exchange of information and the technical knowledge gained by the reporting procedure set up by the Convention. The second Review Meeting is to be held at IAEA headquarters from 15 to 26 May 2006. This paper presents the objectives and the implementation status of the Convention, the

Comparison of Customized Cutting Block and Conventional Cutting Instrument in Total Knee Arthroplasty: A Randomized Controlled Trial.

Science.gov (United States)

Tammachote, Nattapol; Panichkul, Phonthakorn; Kanitnate, Supakit

2018-03-01

Customized cutting block (CCB) was designed to ensure the accurate alignment of knee prostheses during total knee arthroplasty. Given the paucity of CCB efficacy data, we compare CCB with conventional cutting guide using a randomized controlled trial. One hundred eight osteoarthritic knee patients underwent total knee arthroplasty by one experienced surgeon were randomized to receive CCB (n = 54) or conventional cutting instrument (CCI) surgery (n = 54). The primary outcomes were limb alignment, prostheses position, and operative time. The secondary outcomes were hemodynamic alteration after surgery, functional outcomes (modified Western Ontario and McMaster University Osteoarthritis Index) and range of motion at 2 years after surgery. Mean hip-knee-ankle angle in the CCB group was 179.4° ± 1.8° vs 179.1° ± 2.4° in the CCI group, Δ = 0 (95% confidence interval [CI] -0.6 to 1.1, P = .55). Mean operative time was faster in the CCB arm: 93 ± 12 vs 104 ± 12 minutes, Δ = 11 (95% CI -16.7 to -7.2, P < .0001). There were no differences in hemodynamic parameters, mean blood loss (446 [CCB] vs 514 mL [CCI], Δ = -68 [95% CI -138 to 31 mL, P = .21]), postoperative hemoglobin changes, incidence of hypotension (systolic <90 mm Hg), oliguria, and rates of blood transfusion. Functional outcomes and range of motion were also similar. There was no improvement in alignment, hemodynamic changes, blood loss, and knee functional outcomes. CCB reduced surgical time by 11 minutes in our population. CCB cost-effectiveness should be further investigated. Copyright © 2017 Elsevier Inc. All rights reserved.

Instrumentation development

International Nuclear Information System (INIS)

Anon.

1976-01-01

Areas being investigated for instrumentation improvement during low-level pollution monitoring include laser opto-acoustic spectroscopy, x-ray fluorescence spectroscopy, optical fluorescence spectroscopy, liquid crystal gas detectors, advanced forms of atomic absorption spectroscopy, electro-analytical chemistry, and mass spectroscopy. Emphasis is also directed toward development of physical methods, as opposed to conventional chemical analysis techniques for monitoring these trace amounts of pollution related to energy development and utilization

Key convention on safe management of spent fuel and radioactive waste to enter into force

International Nuclear Information System (INIS)

2001-01-01

At a ceremony at IAEA Headquarters today, Ireland deposited its instrument of ratification to an important convention on the safe management of spent fuel and radioactive waste, thereby ensuring its entry into force. The Convention will be the first international instrument to address the safety of management and storage of radioactive wastes and spent fuels in countries with and without nuclear programmes

Energy-efficiency instruments in the electricity area; Instrumente fuer Energieeffizienz im Elektrizitaetsbereich. Auslaendische Erfahrungen und Instrumenten-Mix fuer die Schweiz

Energy Technology Data Exchange (ETDEWEB)

Hammer, S; Oettli, B; Schneider, Ch; Iten, R [Infras, Zuerich (Switzerland); Peherstorfer, N [Oesterreichische Energieagentur, Wien (Austria)

2007-06-15

This comprehensive report for the Swiss Federal Office of Energy (SFOE) describes a mix of instruments that could increase the efficiency of electricity usage in Switzerland. The basis for the development of these instruments - the experience gained in Europe in this area - is discussed. Explicitly not discussed are energy and electricity steering taxes, which could also be part of a future instrument-mix. The measures suggested include the setting of compulsory long-term reduction targets that are to form the basis for strategies and measures to be taken in particular areas and the development of an appropriate instrument-mix for this purpose. These could include regulations and labels, a national fund and certificate trading. Suppliers of electricity could be committed to increasing the efficiency of electricity use and national programmes could also attempt to influence consumer habits. The instruments should, according to the authors, be based on the existing legal framework and use know-how and structures that are already available.

Convention on early notification of a nuclear accident. Convention on assistance in the case of a nuclear accident or radiological emergency

International Nuclear Information System (INIS)

1987-05-01

The document refers to the Convention on early notification of a nuclear accident (INFCIRC-335) and to the Convention on assistance in the case of a nuclear accident or radiological emergency (INFCIRC-336). Part I of the document contains the texts of reservations/declarations made by some of the countries upon or following signature. Part II contains the texts of reservations/declarations made upon or following deposit of instrument, expressing consent to be bound

Protocols to Amend the Paris, Vienna and Brussels Supplementary Conventions and the Convention on Supplementary Compensation for Nuclear Damage: Status of their Implementation into National Legislation

International Nuclear Information System (INIS)

Schwartz, J.

2006-01-01

Over the last decade, a number of very significant developments have taken place in modernising the existing international nuclear liability regimes. The first major advancement was the adoption, in September 1997, of the Protocol to amend the 1963 Vienna Convention on Civil Liability for Nuclear Damage (VC Protocol) and of a new Convention on Supplementary Compensation for Nuclear Damage (CSC). This was followed, in February 2004, by the adoption of Protocols to amend both the 1960 Paris Convention on Third Party Liability in the Field of Nuclear Energy (PC Protocol) and the 1963 Brussels Convention Supplementary to the Paris Convention (BSC Protocol). The principle goal of all these new instruments is to provide a greater amount of compensation to a larger number of victims in respect of a broader scope of nuclear damage suffered as a result of a nuclear accident. The second, but still very important objective is the maintenance of compatibility between the revised Paris and Vienna Conventions to ensure the smooth functioning of the 1988 Joint Protocol Relating to the Application of the Vienna Convention (VC) and the Paris Convention (PC). In addition, the PC States wish to ensure that their newly revised Convention will not prevent a Contracting Party from joining the more global regime established by the CSC. However, it remains to be seen to what extent these new instruments will attract a sufficient number of adherents to make them truly effective. While the VC Protocol is already in force, it has not drawn wide support from the 1963 VC States or from countries with important nuclear generating capacity which have not yet joined that latter any Convention. In addition, notwithstanding its adoption almost 10 years ago, the CSC has not yet entered into force and it remains questionable whether it will ever attract the necessary number of adherents for that purpose, especially in light of its strict requirements in this regard. As for the PC and BSC Protocols to

Isotope-equipped measuring instruments

International Nuclear Information System (INIS)

Miyagawa, Kazuo; Amano, Hiroshi

1980-01-01

In the steel industry, though the investment in isotope-equipped measuring instruments is small as compared with that in machinery, they play important role in the moisture measurement in sintering and blast furnaces, the thickness measurement in rolling process and others in automatic control systems. The economic aspect of the isotope-equipped measuring instruments is described on the basis of the practices in Kimitsu Works of Nippon Steel Corporation: distribution of such instruments, evaluation of economic effects, usefulness evaluation in view of raising the accuracy, and usefulness evaluation viewed from the failure of the isotope instruments. The evaluation of economic effects was made under the premise that the isotope-equipped measuring instruments are not employed. Then, the effects of raising the accuracy are evaluated for a γ-ray plate thickness gauge and a neutron moisture gauge for coke in a blast furnace. Finally, the usefulness was evaluated, assuming possible failure of the isotope-equipped measuring instruments. (J.P.N.)

Verification of the Indicating Measuring Instruments Taking into Account their Instrumental Measurement Uncertainty

Directory of Open Access Journals (Sweden)

Zakharov Igor

2017-12-01

Full Text Available The specific features of the measuring instruments verification based on the results of their calibration are considered. It is noted that, in contrast to the verification procedure used in the legal metrology, the verification procedure for calibrated measuring instruments has to take into account the uncertainty of measurements into account. In this regard, a large number of measuring instruments, considered as those that are in compliance after verification in the legal metrology, turns out to be not in compliance after calibration. In this case, it is necessary to evaluate the probability of compliance of indicating measuring instruments. The procedure of compliance probability determination on the basis of the Monte Carlo method is considered. An example of calibration of a Vernier caliper is given.

Cleaning Effectiveness of a Reciprocating Single-file and a Conventional Rotary Instrumentation System.

Science.gov (United States)

de Carvalho, Fredson Marcio Acris; Gonçalves, Leonardo Cantanhede de Oliveira; Marques, André Augusto Franco; Alves, Vanessa; Bueno, Carlos Eduardo da Silveira; De Martin, Alexandre Sigrist

2016-01-01

To compare cleaning effectiveness by histological analysis of a reciprocating single-file system with ProTaper rotary instruments during the preparation of curved root canals in extracted teeth. A total of 40 root canals with curvatures ranging between 20 - 40 degrees were divided into two groups of 20 canals. Canals were prepared to the following apical sizes: Reciproc size 25 (n=20); ProTaper: F2 (n=20). The normal distribution of data was tested by the Kolmogorov-Smirnov test and the values obtained for the test (Mann-Whitney U test, P .05) between the two groups. The application of reciprocating motion during instrumentation did not result in increased debris when compared with continuous rotation motion, even in the apical part of curved canals. Both instruments resulted in debris in the canal lumen, irrespective of the movement kinematics applied.

Instrumentation for Air Pollution Monitoring

Science.gov (United States)

Hollowell, Craig D.; McLaughlin, Ralph D.

1973-01-01

Describes the techniques which form the basis of current commercial instrumentation for monitoring five major gaseous atmospheric pollutants (sulfur dioxide, oxides of nitrogen, oxidants, carbon monoxide, and hydrocarbons). (JR)

The nuclear liability conventions revised

International Nuclear Information System (INIS)

Reyners, P.

2004-01-01

The signature on 12 February 2004 of the Protocols amending respectively the 1960 Paris Convention and the 1963 Brussels Supplementary Convention was the second step of the process of modernisation of the international nuclear liability regime after the adoption in September 1997 of a Protocol revising the 1963 Vienna Convention and of a new Convention on Supplementary Compensation for Nuclear Damage. The common objective of the new instruments is to provide more funds to compensate a larger number of potential victims in respect of a broader range of damage. Another goal of the revision exercise was to maintain the compatibility between the Paris and Vienna based systems, a commitment enshrined in the 1988 Joint Protocol, as well as to ascertain that Paris/Brussels countries could also become a Party to the Convention on Supplementary Compensation. However, while generally consistent vis a vis the Joint Protocol, the provisions of the Paris and Vienna Conventions, as revised, differ on some significant aspects. Another remaining issue is whether the improved international nuclear liability regime will succeed in attracting in the future a larger number of countries, particularly outside Europe, and will so become truly universal. Therefore, the need for international co-operation to address these issues, to facilitate the adoption of new implementing legislation and to ensure that this special regime keeps abreast of economic and technological developments, is in no way diminished after the revision of the Conventions.(author)

The protocol amending the 1963 Vienna Convention

International Nuclear Information System (INIS)

Lamm, V.

1998-01-01

In the first stage of the revision process, the only goal was to amend certain provisions of the Vienna Convention. Later, in what might be called the second stage, the question was seriously raised of establishing a new supplementary convention by which additional funds were to be provided by the international community of States. Most experts felt that the nuclear liability regime of the Vienna Convention, as amended, would really serve the interests of potential victims of nuclear incidents only if it were supported by an international supplementary fund providing additional compensation for nuclear damage to that provided by the operator. Thus, the Standing Committee started to consider the establishment, under the Vienna Convention, of a mechanism for mobilizing additional funds for compensation of nuclear damage. During the negotiations it was deemed necessary to establish a separate treaty for such a supplementary fund, and indeed, efforts were undertaken to draw up such an instrument concurrently with the revision of the Vienna Convention. (K.A.)

Two-port laparoscopic ovarian cystectomy using 3-mm instruments

Directory of Open Access Journals (Sweden)

Naoyuki Yoshiki

2016-05-01

Conclusion: Two-port laparoscopic ovarian cystectomy using 3-mm instruments is a feasible and safe approach by which surgeons expert in conventional multiport laparoscopy achieve minimally invasive surgery with low morbidity and a low rate of conversion to the conventional approach.

Technical Basis Document (TBD) and user guides

International Nuclear Information System (INIS)

Chiaro, P.J. Jr.

1998-09-01

A Technical Basis Document (TBD) should provide the background information for establishment of an instrument's operational requirements. Due to the amount and location of DOE facilities, no one set of requirements is possible. Operational requirements will vary based on the local environments and missions at each facility. Environmental conditions that can affect an instrument's operations are ambient temperature, humidity, and radio frequency, and to a lesser extent, magnetic fields, and interfering ionizing radiations. Consideration should also be made regarding how an instrument is to be used. If an instrument will be transported around the facility, vibration and shock can cause problems if they are not addressed in the TBD. This document provides guidance for the development of a TBD. This document applies to radiation instruments used for personnel and equipment contamination monitoring, dose rate monitoring, and air monitoring

Recent advances in radiation protection instrumentation

International Nuclear Information System (INIS)

Babu, D.A.R.

2012-01-01

Radiation protection instrumentation plays very important role in radiation protection and surveillance programme. Radiation detector, which appears at the frontal end of the instrument, is an essential component of these instruments. The instrumental requirement of protection level radiation monitoring is different from conventional radiation measuring instruments. Present paper discusses the new type of nuclear radiation detectors, new protection level instruments and associated electronic modules for various applications. Occupational exposure to ionizing radiation can occur in a range of industries, such as nuclear power plants; mining and milling; medical institutions; educational and research establishments; and nuclear fuel cycle facilities. Adequate radiation protection to workers is essential for the safe and acceptable use of radioactive materials for different applications. The radiation exposures to the individual radiation workers and records of their cumulative radiation doses need to be routinely monitored and recorded

The hydrodynamic basis of the vacuum cleaner effect in continuous-flow PCNL instruments: an empiric approach and mathematical model.

Science.gov (United States)

Mager, R; Balzereit, C; Gust, K; Hüsch, T; Herrmann, T; Nagele, U; Haferkamp, A; Schilling, D

2016-05-01

Passive removal of stone fragments in the irrigation stream is one of the characteristics in continuous-flow PCNL instruments. So far the physical principle of this so-called vacuum cleaner effect has not been fully understood yet. The aim of the study was to empirically prove the existence of the vacuum cleaner effect and to develop a physical hypothesis and generate a mathematical model for this phenomenon. In an empiric approach, common low-pressure PCNL instruments and conventional PCNL sheaths were tested using an in vitro model. Flow characteristics were visualized by coloring of irrigation fluid. Influence of irrigation pressure, sheath diameter, sheath design, nephroscope design and position of the nephroscope was assessed. Experiments were digitally recorded for further slow-motion analysis to deduce a physical model. In each tested nephroscope design, we could observe the vacuum cleaner effect. Increase in irrigation pressure and reduction in cross section of sheath sustained the effect. Slow-motion analysis of colored flow revealed a synergism of two effects causing suction and transportation of the stone. For the first time, our model showed a flow reversal in the sheath as an integral part of the origin of the stone transportation during vacuum cleaner effect. The application of Bernoulli's equation provided the explanation of these effects and confirmed our experimental results. We widen the understanding of PCNL with a conclusive physical model, which explains fluid mechanics of the vacuum cleaner effect.

Empirical projection-based basis-component decomposition method

Science.gov (United States)

Brendel, Bernhard; Roessl, Ewald; Schlomka, Jens-Peter; Proksa, Roland

2009-02-01

Advances in the development of semiconductor based, photon-counting x-ray detectors stimulate research in the domain of energy-resolving pre-clinical and clinical computed tomography (CT). For counting detectors acquiring x-ray attenuation in at least three different energy windows, an extended basis component decomposition can be performed in which in addition to the conventional approach of Alvarez and Macovski a third basis component is introduced, e.g., a gadolinium based CT contrast material. After the decomposition of the measured projection data into the basis component projections, conventional filtered-backprojection reconstruction is performed to obtain the basis-component images. In recent work, this basis component decomposition was obtained by maximizing the likelihood-function of the measurements. This procedure is time consuming and often unstable for excessively noisy data or low intrinsic energy resolution of the detector. Therefore, alternative procedures are of interest. Here, we introduce a generalization of the idea of empirical dual-energy processing published by Stenner et al. to multi-energy, photon-counting CT raw data. Instead of working in the image-domain, we use prior spectral knowledge about the acquisition system (tube spectra, bin sensitivities) to parameterize the line-integrals of the basis component decomposition directly in the projection domain. We compare this empirical approach with the maximum-likelihood (ML) approach considering image noise and image bias (artifacts) and see that only moderate noise increase is to be expected for small bias in the empirical approach. Given the drastic reduction of pre-processing time, the empirical approach is considered a viable alternative to the ML approach.

Instrumental development and data processing

International Nuclear Information System (INIS)

Franzen, J.

1978-01-01

A review of recent developments in mass spectrometry instrumentation is presented under the following headings: introduction (scope of mass spectrometry compared with neighbouring fields); ion sources and ionization techniques; spectrometers (instrumental developments); measuring procedures; coupling techniques; data systems; conclusions (that mass spectrometry should have a broader basis and that there would be mutual profit from a better penetration of mass spectrometry into fields of routine application). (U.K.)

Effect of piezoelectric instruments on healing propensity of alveolar sockets following mandibular third molar extraction

OpenAIRE

Shang-Jye Tsai; Yen-Liang Chen; Hao-Hueng Chang; Yow-Chyun Shyu; Chun-Pin Lin

2012-01-01

Background/purpose: The purpose of this study was to investigate whether the use of piezoelectric instruments affected the healing propensity of alveolar sockets after mandibular third molar extraction, compared with conventional rotary instruments. Materials and methods: Thirty patients with impacted bilateral symmetrical mandibular third molars participated in this investigation. We conducted a randomized, crossover study using conventional rotary instruments for extraction on one side a...

Single-incision laparoscopic surgery and conventional laparoscopic ...

African Journals Online (AJOL)

Indications for surgery included grades II-III varicocele or ipsilateral testicular hypotrophy. The SIL-V procedure was performed in 44 patients with roticulating and conventional 5 mm instruments. Testicular vessels were isolated “en bloc,” clipped and cut. Operating time, visual analogue scale and post-operative results were ...

Computer navigation experience in hip resurfacing improves femoral component alignment using a conventional jig.

Science.gov (United States)

Morison, Zachary; Mehra, Akshay; Olsen, Michael; Donnelly, Michael; Schemitsch, Emil

2013-11-01

The use of computer navigation has been shown to improve the accuracy of femoral component placement compared to conventional instrumentation in hip resurfacing. Whether exposure to computer navigation improves accuracy when the procedure is subsequently performed with conventional instrumentation without navigation has not been explored. We examined whether femoral component alignment utilizing a conventional jig improves following experience with the use of imageless computer navigation for hip resurfacing. Between December 2004 and December 2008, 213 consecutive hip resurfacings were performed by a single surgeon. The first 17 (Cohort 1) and the last 9 (Cohort 2) hip resurfacings were performed using a conventional guidewire alignment jig. In 187 cases, the femoral component was implanted using the imageless computer navigation. Cohorts 1 and 2 were compared for femoral component alignment accuracy. All components in Cohort 2 achieved the position determined by the preoperative plan. The mean deviation of the stem-shaft angle (SSA) from the preoperatively planned target position was 2.2° in Cohort 2 and 5.6° in Cohort 1 (P = 0.01). Four implants in Cohort 1 were positioned at least 10° varus compared to the target SSA position and another four were retroverted. Femoral component placement utilizing conventional instrumentation may be more accurate following experience using imageless computer navigation.

The Concept and Practice of Macroprudential Policy in Indonesia: Islamic and Conventional

Directory of Open Access Journals (Sweden)

Muhammad Rizky Prima Sakti

2018-01-01

Full Text Available This study aims to examine reserve ratio (GWM, and capital buffer toward credit growth; the impact of macroeconomic variables and micro-banking specific factors toward credit growth in Islamic and Conventional Bank. This research using Vector Error Correction Model (VECM. This research finds that macroprudential policy based on GWM instrument positively influence the credit growth of conventional and Islamic banks. From macroeconomic, the credit growth is positively affected by GDP and negatively affected by BI Rate and inflation. Also, credit also affected by deposit funds and default rate ratio. Interestingly, there is a different impact of capital buffer instrument toward credit growth. Capital buffer instrument has negatively affected the financing growth of Islamic banks in Indonesia.DOI: 10.15408/aiq.v10i1.5446

Investigating Early and Late Complications in Conventional and LigaSure Hemorroidectomy

Directory of Open Access Journals (Sweden)

M Zare

2014-06-01

Full Text Available Introduction: The traditional Milligan-Morgan and the Ferguson operations are still the most used for patients with symptomatic haemorrhoids of III and IV degrees. Nowadays LigaSure is used as a new technique to decrease the complications resulting from conventional hemorroidectomy. In this study, patients were investigated on the basis of the following main outcomes: mean operative time, postoperative pain (score and duration, bleeding loss in operation, early (within the first month after surgery and late (after the first month complications in conventional as well as LigaSure hemorroidectomy. Methods: it is an analytical study conducted on 101 patients aged 19–80 years old of both males and females with III and IV-degree hemorrhoids who had been gone to Shahid Sadoughi hospital between 2011 and 2012. Forty-three patients were treated by conventional diathermy and fifty -eight by LigaSure. Patients received analgesic administration for about 24 hours after operations and, after hospital discharge. In fact, analgesia was administered until 5 days (three times a day. All patients were required to record pain from the first postoperative day until the 28th postoperative day on a self-administered NAS scale (0–10. Results: Patients completed a questionnaire face to face one week, one month, six, and twelve months after the operation. The mean operative time, bleeding loss in operation and return to work were significantly shorter in LS group, whereas there were no difference in hospital stay period, anal stenosis, healing time of wound and retention of urinary. A statistically significant difference in pain score was observed three and four days after the operation. Finally, patients with LigaSure haemorrhoidectomy recovered from pain earlier than those with conventional diathermy. Conclusions: although LigaSure proposes additional costs, it is an effective instrument in order to treat hemorrhoids of III and IV degrees.

Design type testing for digital instrumentation and control systems

International Nuclear Information System (INIS)

Bastl, W.; Mohns, G.

1997-01-01

The design type qualification of digital safety instrumentation and control is outlined. Experience shows that the concepts discussed, derived from codes, guidelines and standards, achieve useful results. It has likewise become clear that the systematics of design type qualification of the hardware components is also applicable to the software components. Design type qualification of the software, a premiere, could be performed unexpectedly smoothly. The hardware design type qualification proved that the hardware as a substrate of functionality and reliability is an issue that demands full attention, as compared to conventional systems. Another insight is that design qualification of digital instrumentation and control systems must include plant-independent systems tests. Digital instrumentation and control systems simply work very differently from conventional control systems, so that this testing modality is inevitable. (Orig./CB) [de

Percutaneous nephroscopic management of an isolated giant renal hydatid cyst guided by single-incision laparoscopy using conventional instruments: the Santosh-PGI technique.

Science.gov (United States)

Kumar, Santosh; Choudhary, Gautam R; Pushkarna, Arawat; Najjapa, Bhuvnesh; Ht, Vatasla

2013-11-01

Isolated renal hydatid rarely presents, but when it does occur, it requires surgical treatment. We report our experience with a novel technique involving percutaneous management of a giant renal hydatid cyst with single-incision laparoscopic assistance. First we performed retrograde ureteropyelogram, which did not show any communication between the cyst and the calyceal. A Veress needle was used for pneumoperitoneum. Three conventional laparoscopic trocars used. Under laparoscopic guidance, we punctured the cyst. The scolicidal solution used was 10% povidone-iodine. The endocyst was removed under vision with grasping forceps through the nephroscope. A Portex drain was placed into the cyst cavity. Percutaneous aspiration and instillation of scolicidal agents followed by re-aspiration have been previously reported. This is an attractive procedure because of its acceptable success rates and reduced morbidity. In our case, simple aspiration of the cyst would not have been successful because the cyst was full of daughter cysts. Also, a blind percutaneous puncture of the cyst and dilatation could have perforated the colon or the mesocolon, which is often wrapped over the surface of such giant cysts thereby making laparoscopic guidance and mobilization of the colon imperative. We devised this unique treatment method for this patient involving three conventional ports at a single umbilical site. We believe this is the first reported case of its kind in the world. Not only this technique is minimally invasive, it is also cost-effective, as only conventional laparoscopic ports and instruments are used during the procedure. © 2013 Japan Society for Endoscopic Surgery, Asia Endosurgery Task Force and Wiley Publishing Asia Pty Ltd.

Convention on early notification of a nuclear accident. Convention on assistance in the case of a nuclear accident or radiological emergency

International Nuclear Information System (INIS)

1990-08-01

The document refers to the Convention on Early Notification of a Nuclear Accident (IAEA-INFCIRC-335) and to the Convention on Assistance in the Case of a Nuclear Accident or Radiological Emergency (IAEA-INFCIRC-336). Part I contains reservations/declarations made upon or following signature and Part II contains reservations/declarations made upon or following deposit of instrument expressing consent to be bound. The status of signature, ratification, acceptance, approval or accession by States or organizations as of 31 July 1990 is presented in two attachments

Convention of early notification of a nuclear accident. Convention of assistance in the case of a nuclear accident or radiological emergency

International Nuclear Information System (INIS)

1988-05-01

The document refers to the Convention on early notification of a nuclear accident (INFCIRC-335) and to the Convention on assistance in the case of a nuclear accident or radiological emergency (INFCIRC-336). Part I of the document contains reservations/declarations made upon or following signature made by Algeria, Iraq and Thailand. Part II contains reservations/declarations made upon or following deposit of instrument expressing consent to be bound made by Australia, Bulgaria, China, India, Japan, Malaysia, Mongolia, Poland, South Africa, United Arab Emirates and Socialist Republic of Viet Nam. The status of signature, notification, acceptance, approval or accession of the two conventions as of 13 May 1988 is presented in two attachments

Transformation From a Conventional Clinical Microbiology Laboratory to Full Automation.

Science.gov (United States)

Moreno-Camacho, José L; Calva-Espinosa, Diana Y; Leal-Leyva, Yoseli Y; Elizalde-Olivas, Dolores C; Campos-Romero, Abraham; Alcántar-Fernández, Jonathan

2017-12-22

To validate the performance, reproducibility, and reliability of BD automated instruments in order to establish a fully automated clinical microbiology laboratory. We used control strains and clinical samples to assess the accuracy, reproducibility, and reliability of the BD Kiestra WCA, the BD Phoenix, and BD Bruker MALDI-Biotyper instruments and compared them to previously established conventional methods. The following processes were evaluated: sample inoculation and spreading, colony counts, sorting of cultures, antibiotic susceptibility test, and microbial identification. The BD Kiestra recovered single colonies in less time than conventional methods (e.g. E. coli, 7h vs 10h, respectively) and agreement between both methodologies was excellent for colony counts (κ=0.824) and sorting cultures (κ=0.821). Antibiotic susceptibility tests performed with BD Phoenix and disk diffusion demonstrated 96.3% agreement with both methods. Finally, we compared microbial identification in BD Phoenix and Bruker MALDI-Biotyper and observed perfect agreement (κ=1) and identification at a species level for control strains. Together these instruments allow us to process clinical urine samples in 36h (effective time). The BD automated technologies have improved performance compared with conventional methods, and are suitable for its implementation in very busy microbiology laboratories. © American Society for Clinical Pathology 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Computer navigation experience in hip resurfacing improves femoral component alignment using a conventional jig

Directory of Open Access Journals (Sweden)

Zachary Morison

2013-01-01

Full Text Available Background:The use of computer navigation has been shown to improve the accuracy of femoral component placement compared to conventional instrumentation in hip resurfacing. Whether exposure to computer navigation improves accuracy when the procedure is subsequently performed with conventional instrumentation without navigation has not been explored. We examined whether femoral component alignment utilizing a conventional jig improves following experience with the use of imageless computer navigation for hip resurfacing. Materials and Methods:Between December 2004 and December 2008, 213 consecutive hip resurfacings were performed by a single surgeon. The first 17 (Cohort 1 and the last 9 (Cohort 2 hip resurfacings were performed using a conventional guidewire alignment jig. In 187 cases, the femoral component was implanted using the imageless computer navigation. Cohorts 1 and 2 were compared for femoral component alignment accuracy. Results:All components in Cohort 2 achieved the position determined by the preoperative plan. The mean deviation of the stem-shaft angle (SSA from the preoperatively planned target position was 2.2° in Cohort 2 and 5.6° in Cohort 1 ( P = 0.01. Four implants in Cohort 1 were positioned at least 10° varus compared to the target SSA position and another four were retroverted. Conclusions: Femoral component placement utilizing conventional instrumentation may be more accurate following experience using imageless computer navigation.

Temperature documentation - instrument for quality assurance; Temperaturdokumentation - Instrument der Qualitaetssicherung

Energy Technology Data Exchange (ETDEWEB)

Hegglin, A [Wurm AG, Winterthur (Switzerland)

2000-10-01

Important inspection points of a HACCP concept are the temperatures. On the basis of the demands for a systematic temperature documentation, the application of control systems and instruments is described by several examples. (orig.) [German] Wichtige Kontrollpunkte eines HACCP-Konzepts sind die Temperaturen. Ausgehend von den Anforderungen, die an eine systematische Temperaturedokumentation gestellt werden, wird der Einsatz geeigneter Regel- und Ueberwachungsgeraete an mehreren Beispielen erlaeutert. (orig.)

Intracellular recovery - basis of hyperfractionation

International Nuclear Information System (INIS)

Hagen, U.; Guttenberger, R.; Kummermehr, J.

1988-01-01

The radiobiological basis fo a hyperfractionated radiation therapy versus conventional fractionation with respect to therapeutic gain, i.e., improved normal tissue sparing for the same level of tumour cell inactivation, will be presented. Data on the recovery potential of various tissues as well as the kinetics of repair will be given. The problem of incomplete repair with short irradiation intervals will be discussed. (orig.) [de

A simple digital subtraction angiographic instrument

International Nuclear Information System (INIS)

Ando, Hiroshi; Kobayashi, Tsuyoshi; Imai, Yutaka; Yanagishita, Akira

1983-01-01

A digital subtraction angiographic instrument was manufactured using a conventional x-ray TV for gastrointestinal series and a computer for processing of nuclear medical data. The results of visualization of the aorta and its primary branches were reviewed with demonstrable cases. (Chiba, N.)

High-Performance Operational and Instrumentation Amplifiers

NARCIS (Netherlands)

Shahi, B.

2015-01-01

This thesis describes techniques to reduce the offset error in precision instrumentation and operational amplifiers. The offset error which is considered a major error source associated with gain blocks, together with other errors are reviewed. Conventional and newer approaches to remove offset and

Nuclear instrumentation system for the integrated digital I and C system

International Nuclear Information System (INIS)

Isobe, Yuji; Nakamura, Shingo

2005-01-01

Development of a new nuclear instrumentation (NI) system has been done. The new system is suitable for the digital instrumentation and control (I and C) systems. Higher reliability and lower development costs have been achieved by applying good performance circuits with sufficient experience of the conventional NI system. Human-system interface (HSI) and maintainability have been improved comparing with the conventional NI system because of the partial digitalisation. The new NI system has been manufactured and validated. We are finally verifying the total performance now

Nuclear instrumentation system for the integrated digital I and C system

Energy Technology Data Exchange (ETDEWEB)

Isobe, Yuji [Mitsubishi Heavy Industries, Tokyo (Japan); Nakamura, Shingo [Mitsubishi, Electric Corporation, Tokyo (Japan)

2005-11-15

Development of a new nuclear instrumentation (NI) system has been done. The new system is suitable for the digital instrumentation and control (I and C) systems. Higher reliability and lower development costs have been achieved by applying good performance circuits with sufficient experience of the conventional NI system. Human-system interface (HSI) and maintainability have been improved comparing with the conventional NI system because of the partial digitalisation. The new NI system has been manufactured and validated. We are finally verifying the total performance now.

Comparative Study of Determining of the Responsible Person and the Basis of Compensation in Civil Liability Results from Events Related to Nuclear Facilities

Directory of Open Access Journals (Sweden)

Sayyed Mohammad Mahdi Qabuli Dorafshan

2015-12-01

Full Text Available Nuclear facilities, though have large advantages for human being, they also creates heavy hazards. Thus, the question of civil liability results from events of mentioned facilities are so significant. This paper studies the question of the basis and responsible for compensation results from aforementioned events in international instruments, Iran and French law. Outcome of this study shows that in this regard, Paris and Vienna conventions and the other related conventions and protocols adjust a special legal régime. In this respect, the international instruments while distancing themselves from liability based on fault, highlight the exclusive responsibility of the operator of nuclear facilities and they have commited the operator to insurance or appropriate secure financing. Also French legal régime have followed this manner with the impact of the Paris Convention and its amendments and additions. There is no special provisions in Iran legal régime in this matter so civil liability results from nuclear events is under general rules of civil liability and rules such Itlaf (loss, Tasbib (causation, Taqsir (fault and La-zarar (no damage in the context of Imamye jurisprudence. Ofcourse, the responsible is basically the one who the damage is attributable to him. Finaly, It is appropriate that the Iranian legislator predict favorable régime and provides special financial fund for compensation of possible injured parties in accordance with necessities and specific requirements related to nuclear energy

The New International Nuclear Liability Conventions: Status of their Implementation into National Legislation

International Nuclear Information System (INIS)

Schwartz, J.

2008-01-01

Over the last decade or so, a number of significant improvements have been made to the international nuclear liability regimes. The first major advancement was the adoption, in September 1997, of the Protocol to amend the 1963 Vienna Convention on Civil Liability for Nuclear Damage (VC Protocol) and of a new Convention on Supplementary Compensation for Nuclear Damage (CSC). This was followed, in February 2004, by the adoption of Protocols to amend both the 1960 Paris Convention on Third Party Liability in the Field of Nuclear Energy (PC Protocol) and the 1963 Brussels Convention Supplementary to the Paris Convention (BSC Protocol). The principle goal of these new instruments is to provide more compensation to more victims in respect of more types of nuclear damage suffered than ever before. A second objective, at least for the VC and PC Protocols, is to maintain compatibility between the Paris and Vienna Conventions, thereby ensuring the smooth functioning of the 1988 Joint Protocol Relating to the Application of the Vienna Convention (VC) and the Paris Convention (PC). In addition, both Vienna and Paris Convention States wish to ensure that the newly revised Conventions will not prevent them from joining the global liability and compensation regime established by the CSC, should they so wish. However, one wonders to what extent these new instruments will attract a sufficient number of adherents to make them truly effective. While the VC Protocol is already in force, it has drawn surprisingly little support from the 1963 Vienna Convention States and even less from those countries with important nuclear generating capacity but which have not yet joined any of the international nuclear liability and compensation instruments. For its part, and notwithstanding its adoption almost 10 years ago, the CSC has not yet entered into force and only the future will tell whether it ever will, particularly given its strict requirements in this regard. As for the PC and BSC

Digital instrumentation system for nuclear research reactors

International Nuclear Information System (INIS)

Aghina, Mauricio A.C.; Carvalho, Paulo Vitor R.

2002-01-01

This work describes a proposal for a system of nuclear instrumentation and safety totally digital for the Argonauta Reactor. The system divides in the subsystems: channel of pulses, channel of current, conventional instrumentation and safety system. The connection of the subsystems is made through redundant double local net, using the protocol modbus/rtu. So much the channel of pulses, the current channel and safety's system use modules operating in triple redundancy. (author)

Comparison of Radiofrequency and Electrocautery With Conventional Scalpel Incisions.

Science.gov (United States)

Hasar, Zafer Burak; Ozmeric, Nurdan; Ozdemir, Burcu; Gökmenoğlu, Ceren; Baris, Emre; Altan, Gökçen; Kahraman, Sevil

2016-11-01

The disadvantages of conventional scalpels, including insufficient control of bleeding, prompted us to search for new alternative methods such as electrosurgery and radiosurgery. In this study, the conventional scalpel was compared with radiosurgery and electrosurgery for wound healing with assessment of lateral heat production, inflammation, and instrument performance. Incisions were made in the palatal mucosa of 42 Wistar rats using a scalpel, electrocautery instrument, or radiofrequency instrument. Postoperative hemostasis, tissue coagulation, and tissue sticking were measured, and pain evaluation through weight loss was recorded. Gingival biopsy specimens from the surgical area were obtained at the time of surgery and 2, 4, 7, and 14 days postoperatively and were evaluated immunohistochemically for inducible nitric oxide synthase and heat shock protein 70. Kruskal-Wallis, 1-way analysis of variance, and Mann-Whitney U tests were used for statistical evaluation. The rats in the electrosurgery and radiosurgery groups had aggressively greater weight loss when compared with the scalpel group in the first 7 days. Hemostasis was better in the electrocautery group, tissue coagulation was greater in the radiofrequency group (P < .001), and tissue sticking was lesser in the scalpel group (P < .001) compared with the other groups. Inducible nitric oxide synthase expression and heat shock protein 70 expression were similar in all 3 groups. Electrosurgery performed better regarding hemostasis, whereas a scalpel was superior in terms of tissue sticking and tissue coagulation. Radiosurgery was superior regarding hemostasis when compared with a conventional scalpel, but it was not as successful as electrosurgery. Copyright © 2016. Published by Elsevier Inc.

Seismic Instrumentation Placement Recommendations Report

International Nuclear Information System (INIS)

Kennedy, W.N.

1998-01-01

DOE Order 420.1, ''Facility Safety'', requires that facilities or sites with hazardous materials be provided with instrumentation or other means to detect and record the occurrences and severity of seismic events. These requirements assure that necessary records are available after an earthquake for evaluation purposes and to supplement other data to justify a facility restart or curtailing plant operations after an earthquake. This report documents the basis for the selection of Savannah River Site areas and existing facilities to be instrumented. The need to install instrumentation in new facilities such as the Actinide Packaging and Storage Facility, Commercial Light Water Reactor Tritium Extraction Facility and the Accelerator Production of Tritium Facility will be assessed separately

The Inelastic Instrument suite at the SNS

International Nuclear Information System (INIS)

Granroth, Garrett E; Abernathy, Douglas L; Ehlers, Georg; Hagen, Mark E; Herwig, Kenneth W; Mamontov, Eugene; Ohl, Michael E; Wildgruber, Christoph U

2008-01-01

The instruments in the extensive suite of spectrometers at the SNS are in various stages of installation and commissioning. The Back Scattering Spectrometer (BASIS) is installed and is in commissioning. It's near backscattering analyzer crystals provide the 3 eV resolution as expected. BASIS will enter the user program in the fall of 2007. The ARCS wide angular-range thermal to epithermal neutron spectrometer will come on line in the fall of 2007 followed shortly by the Cold Neutron Chopper Spectrometer. These two direct geometry instruments provide moderate resolution and the ability to trade resolution for flux. In addition both instruments have detector coverage out to 140o to provide a large Q range. The SEQUOIA spectrometer, complete in 2008, is the direct geometry instrument that will provide fine resolution in the thermal to epithermal range. The Spin-Echo spectrometer, to be completed on a similar time scale, will provide the finest energy resolution worldwide. The HYSPEC spectrometer, available no later than 2011, will provide polarized capabilities and optimized flux in the thermal energy range. Finally, the Vision chemical spectrometer will use crystal analyzers to study energy transfers into the epithermal range

Effect of environment on fatigue failure of controlled memory wire nickel-titanium rotary instruments.

Science.gov (United States)

Shen, Ya; Qian, Wei; Abtin, Houman; Gao, Yuan; Haapasalo, Markus

2012-03-01

This study examined the fatigue behavior of 2 types of nickel-titanium (NiTi) instruments made from a novel controlled memory NiTi wire (CM wire) under various environment conditions. Three conventional superelastic NiTi instruments of ProFile (Dentsply Maillefer, Ballaigues, Switzerland), Typhoon (Clinician's Choice Dental Products, New Milford, CT), and DS-SS0250425NEYY (Clinician's Choice Dental Products) and 2 new CM wire instruments of Typhoon CM and DS-SS0250425NEYY CM were subjected to rotational bending at the curvature of 35° in air, deionized water, 17% EDTA, or deionized water after immersion in 6% sodium hypochlorite for 25 minutes, and the number of revolutions of fracture (N(f)) was recorded. The fracture surface of all fragments was examined by a scanning electron microscope. The crack-initiation sites and the percentage of dimple area to the whole fracture cross-section were noted. Two new CM Wire instruments yielded an improvement of >4 to 9 times in N(f) than conventional NiTi files with the same design under various environments (P Wire instruments was significantly longer in liquid media than in air (P wire had one crack origin. The values of the area fraction occupied by the dimple region were significantly smaller on CM NiTi instruments than in conventional NiTi instruments under various environments (P < .05). Within the limitations of this study, the type of NiTi metal alloy (CM files vs conventional superelastic NiTi files) influences the cyclic fatigue resistance under various environments. The fatigue life of CM instruments is longer in liquid media than in air. Copyright © 2012 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Thermodynamic basis for effective energy utilization

Energy Technology Data Exchange (ETDEWEB)

Rogers, J. T.

1977-10-15

A major difficulty in a quantitative assessment of effective energy utilization is that energy is always conserved (the First Law of Thermodynamics). However, the Second Law of Thermodynamics shows that, although energy cannot be destroyed, it can be degraded to a state in which it is of no further use for performing tasks. Thus, in considering the present world energy crisis, we are not really concerned with the conservation of energy but with the conservation of its ability to perform useful tasks. A measure of this ability is thermodynamic availability or, a less familiar term, exergy. In a real sense, we are concerned with an entropy-crisis, rather than an energy crisis. Analysis of energy processes on an exergy basis provides significantly different insights into the processes than those obtained from a conventional energy analysis. For example, process steam generation in an industrial boiler may appear quite efficient on the basis of a conventional analysis, but is shown to have very low effective use of energy when analyzed on an exergy basis. Applications of exergy analysis to other systems, such as large fossil and nuclear power stations, are discussed, and the benefits of extraction combined-purpose plants are demonstrated. Other examples of the application of the exergy concept in the industrial and residential energy sectors are also given. The concept is readily adaptable to economic optimization. Examples are given of economic optimization on an availability basis of an industrial heat exchanger and of a combined-purpose nuclear power and heavy-water production plant. Finally, the utility of the concept of exergy in assessing the energy requirements of an industrial society is discussed.

3D printing of surgical instruments for long-duration space missions.

Science.gov (United States)

Wong, Julielynn Y; Pfahnl, Andreas C

2014-07-01

The first off-Earth fused deposition modeling (FDM) 3D printer will explore thermoplastic manufacturing capabilities in microgravity. This study evaluated the feasibility of FDM 3D printing 10 acrylonitrile butadiene styrene (ABS) thermoplastic surgical instruments on Earth. Three-point bending tests compared stiffness and yield strength between FDM 3D printed and conventionally manufactured ABS thermoplastic. To evaluate the relative speed of using four printed instruments compared to conventional instruments, 13 surgeons completed simulated prepping, draping, incising, and suturing tasks. Each surgeon ranked the performance of six printed instruments using a 5-point Likert scale. At a thickness of 5.75 mm or more, the FDM printing process had a less than 10% detrimental effect on the tested yield strength and stiffness of horizontally printed ABS thermoplastic relative to conventional ABS thermoplastic. Significant weakness was observed when a bending load was applied transversely to a 3D printed layer. All timed tasks were successfully performed using a printed sponge stick, towel clamp, scalpel handle, and toothed forceps. There was no substantial difference in time to completion of simulated surgical tasks with control vs. 3D printed instruments. Of the surgeons, 100%, 92%, 85%, 77%, 77%, and 69% agreed that the printed smooth and tissue forceps, curved and straight hemostats, tissue and right angle clamps, respectively, would perform adequately. It is feasible to 3D print ABS thermoplastic surgical instruments on Earth. Loadbearing structures were designed to be thicker, when possible. Printing orientations were selected so that the printing layering direction of critical structures would not be transverse to bending loads.

Application of international maritime protection conventions to radioactive pollution

International Nuclear Information System (INIS)

Stein, R.M.; Walden, R.M.

1975-01-01

The application of international maritime protection conventions to radioactive pollution is discussed with particular emphasis on the 1972 London Convention on prevention of marine pollution by dumping of wastes and other matter. Under that Convention, wastes are divided into three categories according to their radioactivity. High level wastes, whose dumping is prohibited, and low level wastes which require a special dumping permit are studied on the basis of definitions established by the International Atomic Energy Agency. Mention is made of the IAEA-recommended procedures for issue of the specific dumping as well as of the exceptions provided for ships and aircraft enjoying State immunity and cases of force majeure or emergencies. Also dealt with are the other international Conventions applying to prevention of radioactive marine pollution [fr

Backscattering at a pulsed neutron source, the MUSICAL instrument

International Nuclear Information System (INIS)

Alefeld, B.

1995-01-01

In the first part the principles of the neutron backscattering method are described and some simple considerations about the energy resolution and the intensity are presented. A prototype of a backscattering instrument, the first Juelich instrument, is explained in some detail and a representative measurement is shown which was performed on the backscattering instrument IN10 at the ILL in Grenoble. In the second part a backscattering instrument designed for a pulsed neutron source is proposed. It is shown that a rather simple modification, which consists in the replacement of the Doppler drive of the conventional backscattering instrument by a multi silicon monochromator crystal (MUSICAL) leads to a very effective instrument, benefitting from the peak flux of the pulsed source. ((orig.))

Private International Law Issues in Opt-out and Opt-in Instruments of Harmonization

DEFF Research Database (Denmark)

Fogt, Morten Midtgaard

2013-01-01

of Goods from 1980 (CISG) and the European Commission Proposal for a common European Sales Law from 2011 (CESL). Although the two instruments of substantial harmonization regulate the same area of civil law, they differ with respect to the type of formal instrument of harmonization, the material, personal......This article deals with opt-in and opt-out instruments of harmonization, how they apply and compete. It analyses the Private International Law (PIL) issues which arise and bases the analysis on the two instruments of harmonization – the Vienna Convention on Contract for the International Sale...... into these questions and argues, inter alia, that the CISG as a global international convention should have priority over the regional CESL, that the choice of the CESL should be based on a PIL choice of binding European ‘Community rules of law’, that both instruments cannot possible overrule the established PIL...

A comparison of microdebrider assisted endoscopic sinus surgery and conventional endoscopic sinus surgery for nasal polypi.

Science.gov (United States)

Singh, Rohit; Hazarika, Produl; Nayak, Dipak Ranjan; Balakrishnan, R; Gangwar, Navneeta; Hazarika, Manali

2013-07-01

Nasal polyposis is often encountered in rhinology practice. Those who fail conservative management, a definitive surgery is essential to achieve sufficient ventilation and drainage of the affected sinuses by using either microdebrider or conventional instruments for functional endoscopic sinus surgery (FESS). A prospective study was conducted on 40 cases of nasal polypi in a tertiary care hospital. 20 cases were operated by conventional endoscopic instruments and 20 using the microdebrider. The study aimed at comparing the intra operative (blood loss, duration of surgery) and post operative results (crusting, scarring, discharge, symptoms, recurrence) between the two groups using Lund-Mackay scoring system and the data was statistically analysed. There was no statistically significant difference in surgical outcome for patients when either conventional endoscopic instruments or microdebrider was used. However, there was a significant symptomatic improvement in cases undergoing microdebrider FESS. Microdebrider assisted polypectomy is precise, relatively bloodless surgery though the precision depends on the surgeon's anatomical knowledge and operative skills. Study substantiates that these instruments are helpful but not a prerequisite for successful outcomes in FESS. The study re-emphasises the utility of the microdebrider to young learning FESS surgeons.

Comparison of cyclic fatigue resistance of novel nickel-titanium rotary instruments.

Science.gov (United States)

Capar, Ismail Davut; Ertas, Huseyin; Arslan, Hakan

2015-04-01

New files (ProTaper Next/HyFlex/OneShape) are made from novel nickel-titanium (NiTi) alloys/treatments. The purpose of this study was to compare the cyclic fatigue resistance of these new instruments with that of Revo-S instruments. Four groups of 20 NiTi endodontic instruments were tested in steel canals with a 3 mm radius and a 60° angle of curvature. The cyclic fatigue of the following NiTi instruments with a tip size 25 and 0.06 taper that were manufactured with different alloys was tested: ProTaper Next X2 (M-Wire), OneShape (conventional NiTi), Revo-S Shaping Universal (conventional NiTi) and HyFlex 25/0.6 (controlled memory NiTi wire). A one-way anova and post-hoc Tukey's test (α = 0.05) revealed that the HyFlex files had the highest fatigue resistance and the Revo-S had the least fatigue resistance among the groups (P < 0.001). © 2014 Australian Society of Endodontology.

Vienna convention on civil liability for nuclear damage

International Nuclear Information System (INIS)

1996-01-01

The Vienna Convention on Civil Liability for Nuclear Damage was adopted on 21 May 1963 and was opened for signature on the same day. It entered into force on 12 November 1977, i.e. three months after the date of deposit with the Director General of the fifth instrument of ratification, in accordance with Article 23

Vienna convention on civil liability for nuclear damage

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-20

The Vienna Convention on Civil Liability for Nuclear Damage was adopted on 21 May 1963 and was opened for signature on the same day. It entered into force on 12 November 1977, i.e. three months after the date of deposit with the Director General of the fifth instrument of ratification, in accordance with Article 23.

Application of Fiber Optic Instrumentation

Science.gov (United States)

Richards, William Lance; Parker, Allen R., Jr.; Ko, William L.; Piazza, Anthony; Chan, Patrick

2012-01-01

Fiber optic sensing technology has emerged in recent years offering tremendous advantages over conventional aircraft instrumentation systems. The advantages of fiber optic sensors over their conventional counterparts are well established; they are lighter, smaller, and can provide enormous numbers of measurements at a fraction of the total sensor weight. After a brief overview of conventional and fiber-optic sensing technology, this paper presents an overview of the research that has been conducted at NASA Dryden Flight Research Center in recent years to advance this promising new technology. Research and development areas include system and algorithm development, sensor characterization and attachment, and real-time experimentally-derived parameter monitoring for ground- and flight-based applications. The vision of fiber optic smart structure technology is presented and its potential benefits to aerospace vehicles throughout the lifecycle, from preliminary design to final retirement, are presented.

Neuromorphic elements and systems as the basis for the physical implementation of artificial intelligence technologies

Science.gov (United States)

Demin, V. A.; Emelyanov, A. V.; Lapkin, D. A.; Erokhin, V. V.; Kashkarov, P. K.; Kovalchuk, M. V.

2016-11-01

The instrumental realization of neuromorphic systems may form the basis of a radically new social and economic setup, redistributing roles between humans and complex technical aggregates. The basic elements of any neuromorphic system are neurons and synapses. New memristive elements based on both organic (polymer) and inorganic materials have been formed, and the possibilities of instrumental implementation of very simple neuromorphic systems with different architectures on the basis of these elements have been demonstrated.

Comparison of instrumented anterior interbody fusion with instrumented circumferential lumbar fusion.

Science.gov (United States)

Madan, S S; Boeree, N R

2003-12-01

Posterior lumbar interbody fusion (PLIF) restores disc height, the load bearing ability of anterior ligaments and muscles, root canal dimensions, and spinal balance. It immobilizes the painful degenerate spinal segment and decompresses the nerve roots. Anterior lumbar interbody fusion (ALIF) does the same, but could have complications of graft extrusion, compression and instability contributing to pseudarthrosis in the absence of instrumentation. The purpose of this study was to assess and compare the outcome of instrumented circumferential fusion through a posterior approach [PLIF and posterolateral fusion (PLF)] with instrumented ALIF using the Hartshill horseshoe cage, for comparable degrees of internal disc disruption and clinical disability. It was designed as a prospective study, comparing the outcome of two methods of instrumented interbody fusion for internal disc disruption. Between April 1994 and June 1998, the senior author (N.R.B.) performed 39 instrumented ALIF procedures and 35 instrumented circumferential fusion with PLIF procedures. The second author, an independent assessor (S.M.), performed the entire review. Preoperative radiographic assessment included plain radiographs, magnetic resonance imaging (MRI) and provocative discography in all the patients. The outcome in the two groups was compared in terms of radiological improvement and clinical improvement, measured on the basis of improvement of back pain and work capacity. Preoperatively, patients were asked to fill out a questionnaire giving their demographic details, maximum walking distance and current employment status in order to establish the comparability of the two groups. Patient assessment was with the Oswestry Disability Index, quality of life questionnaire (subjective), pain drawing, visual analogue scale, disability benefit, compensation status, and psychological profile. The results of the study showed a satisfactory outcome (scorelife questionnaire) score of 71.8% (28 patients) in

The Design of Compressed air system in the Conventional Facility of Proton Accelerator Research Center

International Nuclear Information System (INIS)

Jeon, G. P.; Kim, J. Y.; Cho, S. W.; Min, Y. S.; Mun, K. J.; Cho, J. S.; Nam, J. M.; Park, S. S.; Jo, J. H.

2012-01-01

The Compressed Air System (CA) supplies compressed air for all air operated devices and instruments, pneumatic equipment and other miscellaneous air user points in the Conventional Facilities of Proton Engineering Frontier Project. CA System consist of the Instrument Air System and the Service air System. The Instrument Air System supplies oil-free, dried, filtered, and compressed instrument air for the air operated control devices and instruments in the Accelerator and Beam Application Building, Ion Beam Application Building, Utility Building and etc.. The Service air System supplies compressed air for pneumatic equipment and other services

In vitro assessment of cutting efficiency and durability of zirconia removal diamond rotary instruments.

Science.gov (United States)

Kim, Joon-Soo; Bae, Ji-Hyeon; Yun, Mi-Jung; Huh, Jung-Bo

2017-06-01

Recently, zirconia removal diamond rotary instruments have become commercially available for efficient cutting of zirconia. However, research of cutting efficiency and the cutting characteristics of zirconia removal diamond rotary instruments is limited. The purpose of this in vitro study was to assess and compare the cutting efficiency, durability, and diamond rotary instrument wear pattern of zirconia diamond removal rotary instruments with those of conventional diamond rotary instruments. In addition, the surface characteristics of the cut zirconia were assessed. Block specimens of 3 mol% yttrium cation-doped tetragonal zirconia polycrystal were machined 10 times for 1 minute each using a high-speed handpiece with 6 types of diamond rotary instrument from 2 manufacturers at a constant force of 2 N (n=5). An electronic scale was used to measure the lost weight after each cut in order to evaluate the cutting efficiency. Field emission scanning electron microscopy was used to evaluate diamond rotary instrument wear patterns and machined zirconia block surface characteristics. Data were statistically analyzed using the Kruskal-Wallis test, followed by the Mann-Whitney U test (α=.05). Zirconia removal fine grit diamond rotary instruments showed cutting efficiency that was reduced compared with conventional fine grit diamond rotary instruments. Diamond grit fracture was the most dominant diamond rotary instrument wear pattern in all groups. All machined zirconia surfaces were primarily subjected to plastic deformation, which is evidence of ductile cutting. Zirconia blocks machined with zirconia removal fine grit diamond rotary instruments showed the least incidence of surface flaws. Although zirconia removal diamond rotary instruments did not show improved cutting efficiency compared with conventional diamond rotary instruments, the machined zirconia surface showed smoother furrows of plastic deformation and fewer surface flaws. Copyright © 2016 Editorial Council

Metallurgical characterization of controlled memory wire nickel-titanium rotary instruments.

Science.gov (United States)

Shen, Ya; Zhou, Hui-Min; Zheng, Yu-Feng; Campbell, Les; Peng, Bin; Haapasalo, Markus

2011-11-01

To improve the fracture resistance of nickel-titanium (NiTi) files, manufacturers have introduced new alloys and developed new manufacturing processes for the fabrication of NiTi files. This study aimed to examine the phase transformation behavior and microstructure of NiTi instruments from a novel controlled memory NiTi wire (CM wire). Instruments of EndoSequence (ES), ProFile (PF), ProFile Vortex (Vortex), Twisted Files (TF), Typhoon (TYP), and Typhoon™ CM (TYP CM), all size 25/.04, were examined by differential scanning calorimetry (DSC) and x-ray diffraction (XRD). Microstructures of etched instruments were observed by optical microscopy and scanning electron microscopy with x-ray energy-dispersive spectrometric (EDS) analyses. The DSC analyses showed that each segment of the TYP CM and Vortex instruments had an austenite transformation completion or austenite-finish (A(f)) temperature exceeding 37°C, whereas the NiTi instruments made from conventional superelastic NiTi wire (ES, PF, and TYP) and TF had A(f) temperatures substantially below mouth temperature. The higher A(f) temperature of TYP CM instruments was consistent with a mixture of austenite and martensite structure, which was observed at room temperature with XRD. All NiTi instruments had room temperature martensite microstructures consisting of colonies of lenticular features with substantial twinning. EDS analysis indicated that the precipitates in all NiTi instruments were titanium-rich, with an approximate composition of Ti(2)Ni. The TYP CM and Vortex instruments with heat treatment contribute to increase austenite transformation temperature. The CM instrument has significant changes in the phase transformation behavior, compared with conventional superelastic NiTi instruments. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Revision of the Paris and Brussels Conventions of Nuclear Liability

International Nuclear Information System (INIS)

Reyners, P.

2002-01-01

The Contracting Parties to the 1960 Paris Convention on Third Party Liability in the Field of Nuclear Energy and to the 1963 Brussels Convention Supplementary to the Paris Convention, have concluded this Spring four years of negotiation on the revision of these instruments. This exercise was itself started as a logical consequence of the adoption in 1997 of a revised Vienna Convention on Civil Liability for Nuclear Damage and of a Convention on Supplementary Compensation for Nuclear Damage. The Contracting Parties have concluded that the existing regime established by these Conventions remains viable and sound but that it also warrants improvements to ensure that greater financial security will be available to compensate a potentially larger number of victims in respect of a broader range of nuclear damage. A number of more technical amendments have also been agreed, in particular to ensure compatibility with other existing Conventions in this field. When the revised Paris and Brussels Conventions come into force, the total amount of funds available for compensation, provided by the liable nuclear operator and by the States concerned, will be 1.5 billion euros. (author)

Entry into force of the Convention on Supplementary Compensation for Nuclear Damage: Opening the umbrella

International Nuclear Information System (INIS)

McRae, Ben

2015-01-01

There are 431 commercial nuclear power plants around the world. On 14 April 2015, 193 of these power plants were covered by a nuclear liability instrument (118 power plants by the Paris Convention and 75 by the Vienna Convention). With the entry into force of the Convention on Supplementary Compensation for Nuclear Damage (CSC)4 on 15 April 2015, the number of power plants covered by a nuclear liability instrument increased to 340. Thus, the entry into force of the CSC marked a major milestone towards the establishment of a global nuclear liability regime. This article discusses several events that have promoted progress towards a global nuclear liability regime and then addresses several questions that may arise as countries consider actions necessary to achieve such a regime. (author)

Industrial measurement instruments that use radioisotopes

International Nuclear Information System (INIS)

Monno, Asao

2004-01-01

An example of a large-scale system for controlling hot rolling, and recent developments for a gamma-ray thickness gauge for the inner-mill housing of a plate and a thickness gauge for a hot seamless tube mill are introduced. The dramatically higher speed response, versatile intelligent elements, larger data capacity and formation of a database are advantages of these instruments over conventional devices. Moreover, Fuji Electric's industrial measuring instruments that use radioisotopes are manufactured and marketed to be compatible with those of Hitachi, and we have already compiled a track record of many deliveries. (author)

DO WE STILL NEED A CONVENTION IN THE FIELD OF HARMONISATION OF THE INTERNATIONAL COMMERCIAL LAW?

Directory of Open Access Journals (Sweden)

A. Korzhevskaya

2014-01-01

Full Text Available The paper critically discusses the opinion of certain scholars that the use of multilateral treaties (conventions in the field of harmonisation of international commercial law has been in a state of steady decline. They believe that traditional treaty law has been gradually replaced in recent years by softer methods of making international law, such as the use of restatements and model laws. Some scholars even claim that treaty law is dead or dying. The work assesses whether this view has reasonable grounds, providing an overview of the most prominent hard law and soft law harmonising instruments and outlining issues relating to the success of conventions, their advantages, drawbacks and tensions arising in this area. The paper suggests that conventions remain necessary where the third party or public interest are at stake, however, further improvements are needed to make conventions more successful instruments in international commercial law.

Finite Element Study on Continuous Rotating versus Reciprocating Nickel-Titanium Instruments.

Science.gov (United States)

El-Anwar, Mohamed I; Yousief, Salah A; Kataia, Engy M; El-Wahab, Tarek M Abd

2016-01-01

In the present study, GTX and ProTaper as continuous rotating endodontic files were numerically compared with WaveOne reciprocating file using finite element analysis, aiming at having a low cost, accurate/trustworthy comparison as well as finding out the effect of instrument design and manufacturing material on its lifespan. Two 3D finite element models were especially prepared for this comparison. Commercial engineering CAD/CAM package was used to model full detailed flute geometries of the instruments. Multi-linear materials were defined in analysis by using real strain-stress data of NiTi and M-Wire. Non-linear static analysis was performed to simulate the instrument inside root canal at a 45° angle in the apical portion and subjected to 0.3 N.cm torsion. The three simulations in this study showed that M-Wire is slightly more resistant to failure than conventional NiTi. On the other hand, both materials are fairly similar in case of severe locking conditions. For the same instrument geometry, M-Wire instruments may have longer lifespan than the conventional NiTi ones. In case of severe locking conditions both materials will fail similarly. Larger cross sectional area (function of instrument taper) resisted better to failure than the smaller ones, while the cross sectional shape and its cutting angles could affect instrument cutting efficiency.

Safeguards instrumentation: past, present, future

International Nuclear Information System (INIS)

Higinbotham, W.A.

1982-01-01

Instruments are essential for accounting, for surveillance and for protection of nuclear materials. The development and application of such instrumentation is reviewed, with special attention to international safeguards applications. Active and passive nondestructive assay techniques are some 25 years of age. The important advances have been in learning how to use them effectively for specific applications, accompanied by major advances in radiation detectors, electronics, and, more recently, in mini-computers. The progress in seals has been disappointingly slow. Surveillance cameras have been widely used for many applications other than safeguards. The revolution in TV technology will have important implications. More sophisticated containment/surveillance equipment is being developed but has yet to be exploited. On the basis of this history, some expectations for instrumentation in the near future are presented

Influence of Cyclic Flexural Deformation on the Torsional Resistance of Controlled Memory and Conventional Nickel-titanium Instruments.

Science.gov (United States)

Acosta, Eufemia Carolina Peláez; Resende, Pedro Damas; Peixoto, Isabella Faria da Cunha; Pereira, Érika Sales Joviano; Buono, Vicente Tadeu Lopes; Bahia, Maria Guiomar de Azevedo

2017-04-01

The aim of this study was to evaluate the influence of cyclic deformation on the torsional resistance of controlled memory (CM) nickel-titanium files in comparison with superelastic (SE) instruments with similar geometric and dimensional characteristics. New 30/.06 HyFlex (HF; Coltene/Whaledent, Inc, Cuyahoga Falls, OH), Typhoon (Clinician's Choice Dental Products, New Milford, CT), RaCe (FKG, La-Chaux De Fonds, Switzerland), and ProTaper Universal F2 instruments (F2; Dentsply Maillefer, Ballaigues, Switzerland) were assessed. The diameter and pitch length were measured along the active part of the instruments. The number of cycles to failure (Nf) in flexural fatigue and the torsional resistance were evaluated for new files (n = 10). Ten new instruments of each type were fatigued to 3/4 of their fatigue life and then submitted to torsion until rupture. Data were analyzed using 1-way analysis of variance (α = .05). New CM files had a significantly higher Nf when compared with SE instruments; HF exhibited the highest value (P = .001). The mean torque value for F2 was the highest (P = .001). CM files precycled to 3/4 Nf had a significantly lower torque than the new files (HF: P = .003, Typhoon: P = .001), whereas the SE instruments displayed no significant differences (F2: P = .059, RaCe: P = .079). Cyclic flexural loading significantly reduced the torsional resistance of CM instruments. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Towards a treaty instrument on marine genetic resources

OpenAIRE

Wehrli Judith; Cottier Thomas

2014-01-01

Marine genetic resources other than fish and mammals are of increasing commercial interest and importance in genetic engineering but fail being properly addressed in the law of the sea and in international economic law. The paper analyses the implication of the United Nations Convention on the Law of the Sea the Convention on Biodiversity the WTO Agreement on Trade Related Aspects of Intellectual Property Rights and related instruments under the auspices of WIPO. The paper argues that the tri...

New type of radiation instrumentation system

International Nuclear Information System (INIS)

Matsuo, Keichi; Takaoka, Akira; Uranaka, Yasuo

2000-01-01

The Mitsubishi Electric Co., Ltd. developed a radiation instrumentation system introduced some recent techniques such as computation technique, network technique and so on into conventional radiation detection aiming at general market except power generation company. In a conventional system, a detector and an operation processing board was placed at a field and center, respectively, and a feeble pulse signal from the detector was transferred to the operation processing board. Then, on establishment of cables, detectors and operation processing board, it is essential to carry out engineering planning and field engineering conceiving on noise countermeasure. Noise resistance of the new type of radiation instrumentation system, not by adding operation processing function and network interface function into a detector unit in a field to transfer feeble signal, but by transferring testing result as a digital signal. And, noise removing function capable of selectively passing only signal pulse waveform from the detector to judge its signal waveform was also added to a detector unit in the field, to carry out a thoroughly removing noise. In addition, by connecting between each apparatus placed at the field with a network a system capable of reducing some cable engineering could be executed. Here were introduced on abstract of this new type of radiation instrumentation system and on noise removing function of its characteristics. (G.K.)

Performance and quality control of nuclear medicine instrumentation

International Nuclear Information System (INIS)

Paras, P.

1981-01-01

The status and the recent developments of nuclear medicine instrumentation performance, with an emphasis on gamma-camera performance, are discussed as the basis for quality control. New phantoms and techniques for the measurement of gamma-camera performance parameters are introduced and their usefulness for quality control is discussed. Tests and procedures for dose calibrator quality control are included. Also, the principles of quality control, tests, equipment and procedures for each type of instrument are reviewed, and minimum requirements for an effective quality assurance programme for nuclear medicine instrumentation are suggested. (author)

Conference report. Fourth review meeting of the parties of the Joint Convention

International Nuclear Information System (INIS)

Brennecke, Peter

2012-01-01

The Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management, the first legal instrument to directly address these topics on a global scale, was opened for signature 29 September 1997. It entered into force 18 June 2001. The Convention calls for triannual review meetings of the Contracting Parties. Each Contracting Party is required to submit a national report to each review meeting that addresses measures taken to implement each of the obligations of the Convention. The first review meeting took place in 2003. The 4 th review meeting of this Convention took place from 14 to 23 May 2012 at the International Atomic Energy Agency (IAEA) Headquarter in Vienna/Austria. (orig.)

Geosciences research: development of techniques and instruments for investigation geological environments

International Nuclear Information System (INIS)

1993-01-01

In order to understand the geological environment in Japan, new investigation techniques have been developed. These include: 1) Geological techniques for fracture characterization, 2) Nondestructive investigation techniques for detailed geological structure, 3) Instruments for hydraulic characterization, 4) Instruments for hydrochemical characterization. Results so far obtained are: 1) Fractures can be classified by their patterns, 2) The applicability and limitations of conventional geophysical methods were defined, 3) Instruments for measuring very low permeability were successfully developed, 4) Instruments for sampling formation water without changing in-situ conditions were developed. (author)

Stakeholder involvement in international conventions governing civil nuclear activities

International Nuclear Information System (INIS)

Emmerechts, Sam

2017-01-01

Mr Emmerechts explained that international conventions have varying positions on stakeholders and their involvement depending upon the intent of the legislator and the field they cover, ranging from a narrow to a broad interpretation. He addressed stakeholder involvement in two other international conventions governing civil nuclear activities, namely the Convention on Nuclear Safety, and the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management (the Joint Convention), both concluded under the auspices of the International Atomic Energy Agency (IAEA). He noted that the Convention on Nuclear Safety remains a 'traditional' international legal instrument, focusing on governments and governmental bodies as the main stakeholders and limiting obligations regarding the involvement of the public and intergovernmental organisations to their receiving information and observing. Likewise, the Joint Convention limits obligations regarding public involvement to access to information, notably as to the siting of proposed facilities. However, he noted that in the European Union, the Directive on Nuclear Safety (2014/87/Euratom) and the Directive for the Safe Management of Spent Fuel and Radioactive Waste (2011/70/Euratom) have more advanced public participation requirements in nuclear decision making. Mr Emmerechts explained that the substantial differences between nuclear legislation and the Aarhus and Espoo Conventions with regards to public involvement requirements could partly be explained by the technicality of nuclear information and by issues related to nuclear security

Neutron scattering instruments for the Spallation Neutron Source (SNS)

International Nuclear Information System (INIS)

Crawford, R.K.; Fornek, T.; Herwig, K.W.

1998-01-01

The Spallation Neutron Source (SNS) is a 1 MW pulsed spallation source for neutron scattering planned for construction at Oak Ridge National Laboratory. This facility is being designed as a 5-laboratory collaboration project. This paper addresses the proposed facility layout, the process for selection and construction of neutron scattering instruments at the SNS, the initial planning done on the basis of a reference set of ten instruments, and the plans for research and development (R and D) to support construction of the first ten instruments and to establish the infrastructure to support later development and construction of additional instruments

Tomographic Approach in Three-Orthogonal-Basis Quantum Key Distribution

International Nuclear Information System (INIS)

Liang Wen-Ye; Yin Zhen-Qiang; Chen Hua; Li Hong-Wei; Chen Wei; Han Zheng-Fu; Wen Hao

2015-01-01

At present, there is an increasing awareness of some three-orthogonal-basis quantum key distribution protocols, such as, the reference-frame-independent (RFI) protocol and the six-state protocol. For secure key rate estimations of these protocols, there are two methods: one is the conventional approach, and another is the tomographic approach. However, a comparison between these two methods has not been given yet. In this work, with the general model of rotation channel, we estimate the key rate using conventional and tomographic methods respectively. Results show that conventional estimation approach in RFI protocol is equivalent to tomographic approach only in the case of that one of three orthogonal bases is always aligned. In other cases, tomographic approach performs much better than the respective conventional approaches of the RFI protocol and the six-state protocol. Furthermore, based on the experimental data, we illustrate the deep connections between tomography and conventional RFI approach representations. (paper)

International conventions on civil liability for nuclear damage. Revised 1976 ed.

International Nuclear Information System (INIS)

1976-01-01

This revised edition contains the texts of the following multilateral conventions and instruments concerning civil liability for nuclear damage: The Vienna Convention of 21 May 1963 on Civil Liability for Nuclear Damage; The Paris Convention of 29 July 1960 on Third Party Liability in the Field of Nuclear Energy (incorporating the provisions of the Additional Protocol of 28 January 1964); The Brussels Convention of 31 January 1963; Supplementary to the Paris Convention of 29 July 1960 (and incorporating the provisions of the Additional Protocol signed in Paris on 28 January 1964); and the Brussels Convention of 25 May 1962 on the Liability of Operators of Nuclear Ships. Final Act and Resolutions of the International Conference on Civil Liability for Nuclear Damage, held in Vienna from 29 April to 19 May 1963; Final Act of the International Legal Conference on Maritime Carriage of Nuclear Substances, held in Brussels from 29 November to 2 December 1971; and Convention Relating to Civil Liability in the Field of Maritime Carriage of Nuclear Material, adopted at Brussels on 17 December 1971

Convention on the physical protection of nuclear material

International Nuclear Information System (INIS)

1990-08-01

The document refers to the Convention on the Physical Protection of Nuclear Material (INFCIRC/274). Part I contains reservations/declarations made upon or following signature and Part II contains reservations/declarations made upon or following deposit of instrument of consent to be bound. The status of signature, ratification, acceptance, approval or accession by States or organizations as of 31 July 1990 is presented in an attachment

Instrument cables and ceramic-to-metal seals for fusion-environment service

International Nuclear Information System (INIS)

Cannon, C.P.

1982-10-01

The intent of this paper is to form a technical basis to address questions pertinent to the use of instrument cables, ceramic-to-metal seals, and connector components in a fusion environment. The service environment of future fusion devices poses a unique challenge to instrumentation. The radiation environment of 14 MeV neutrons is markedly different from other instrumented radiation environments. There exist other environmental concerns as well (some instruments may operate at elevated temperatures, etc)

The Burning Plasma Experiment conventional facilities

International Nuclear Information System (INIS)

Commander, J.C.

1991-01-01

The Burning Program Plasma Experiment (BPX) is phased to start construction of conventional facilities in July 1994, in conjunction with the conclusion of the Tokamak Fusion Test Reactor (TFTR) project. This paper deals with the conceptual design of the BPX Conventional Facilities, for which Functional and Operational Requirements (F ampersand ORs) were developed. Existing TFTR buildings and utilities will be adapted and used to satisfy the BPX Project F ampersand ORs to the maximum extent possible. However, new conventional facilities will be required to support the BPX project. These facilities include: The BPX building; Site improvements and utilities; the Field Coil Power Conversion (FCPC) building; the TFTR modifications; the Motor Generation (MG) building; Liquid Nitrogen (LN 2 ) building; and the associated Instrumentation and Control (I ampersand C) systems. The BPX building will provide for safe and efficient shielding, housing, operation, handling, maintenance and decontamination of the BPX and its support systems. Site improvements and utilities will feature a utility tunnel which will provide a space for utility services--including pulse power duct banks and liquid nitrogen coolant lines. The FCPC building will house eight additional power supplied for the Toroidal Field (TF) coils. The MG building will house the two MG sets larger than the existing TFTR MG sets. This paper also addresses the conventional facility cost estimating methodology and the rationale for the construction schedule developed. 6 figs., 1 tab

The conventional ammunition requirements determination process of the U.S. Navy.

OpenAIRE

Mawson, John III

1985-01-01

Approved for public release; distribution is unlimited The objective of this thesis is to analyze the Requirements Determination procedures in the Navy's Conventional Gun Ammunition System in an attempt to identify areas for potential improvement. The Conventional Gun Ammunition System involves a logical progression of steps initiated on an annual basis. The Secretary of Defense begins the process by issuing broad guidance for the development of documentation to support b...

Technical basis for instrumentation and control design improvements in WWER-440/230 nuclear power plants. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1996-01-01

Instrumentation and control (I and C) has been recognized as an area which requires substantial improvements in WWER NNPs, particularly for model 230 plants. Under contract with the IAEA the Spanish company Empresarios Agrupados (EA) developed a basic document proposing a technical basis for improvements related to the following most significant aspects of I and C: criteria for safety classification; remote shutdown panel; I and C support to operation and control room design; instrumentation set point margins; accident monitoring instrumentation. This publication is derived from the original report of EA which was circulated by the IAEA for review by staff members and experts from various Member States. It was finally agreed upon at a Consultants' meeting convened by the IAEA in Vienna in May 1994 with the participation of experts from France, Germany and Spain. The guidance expressed in this report is based on the IAEA/NUSS standards, safety guides and practices, and on regulations in use in various Member States. It is proposed as a way of carrying out the necessary studies to improve safety by upgrading the vital part of instrumentation an control in WWER-440 model 230 nuclear power plants. 28 refs, 3 figs

Instrumentation, controls and automation in the power industry

International Nuclear Information System (INIS)

Anon.

1991-01-01

The year 1991 will be remembered as the year EPRI joined with the ISA Power Division to present an outstanding group to technical papers at the First Annual ISA/EPRI Joint Controls and Automation Conference. All papers met the theme for the conference namely Innovative Instrumentation, Controls, and Automation Techniques for the Power Generation Industry and cover a myriad of application ranging from nuclear to conventional fossil to co-generation plants involving nuclear, conventional BTG, and combined cycle equipment applications

Customisation of an instrument to assess anaesthesiologists' non-technical skills.

Science.gov (United States)

Jepsen, Rikke M H G; Spanager, Lene; Lyk-Jensen, Helle T; Dieckmann, Peter; Østergaard, Doris

2015-02-22

The objectives of the study were to identify Danish anaesthesiologists' non-technical skills and to customise the Scottish-developed Anaesthetists' Non-Technical Skills instrument for Danish anaesthesiologists. Six semi-structured group interviews were conducted with 31 operating room team members: anaes-thesiologists, nurse anaesthetists, surgeons, and scrub nurses. Interviews were transcribed verbatim and analysed using directed content analysis. Anaesthesiologists' non-technical skills were identified, coded, and sorted using the original instrument as a basis. The resulting prototype instrument was discussed with anaesthesiologists from 17 centres to ensure face validity. Interviews lasted 46-67 minutes. Identified examples of anaesthesiologists' good or poor non-technical skills fit the four categories in the original instrument: situation awareness; decision making; team working; and task management. Anaesthesiologists' leadership role in the operating room was emphasised: the original 'Task Management' category was named 'Leadership'. One new element, 'Demonstrating self-awareness' was added under the category 'Situation Awareness'. Compared with the original instrument, half of the behavioural markers were new, which reflected that being aware of and communicating one's own abilities to the team; working systematically; and speaking up to avoid adverse events were important skills. The Anaesthetists' Non-Technical Skills instrument was customised to a Danish setting using the identified non-technical skills for anaesthesiologists and the original instrument as basis. The customised instrument comprises four categories and 16 underpinning elements supported by multiple behavioural markers. Identifying non-technical skills through semi-structured group interviews and analysing them using direct content analysis proved a useful method for customising an assessment instrument to another setting.

Fatigue testing of controlled memory wire nickel-titanium rotary instruments.

Science.gov (United States)

Shen, Ya; Qian, Wei; Abtin, Houman; Gao, Yuan; Haapasalo, Markus

2011-07-01

To improve the fracture resistance of nickel-titanium (NiTi) files, manufacturers have introduced new alloys to manufacture NiTi files and developed new manufacturing processes. This study was aimed to examine the fatigue behavior of NiTi instruments from a novel controlled memory NiTi wire (CM Wire). Instruments of ProFile, Typhoon (TYP), Typhoon CM (TYP CM), DS-SS0250425NEYY (NEYY), and DS-SS0250425NEYY CM (NEYY CM) (DS Dental, Johnson City, TN) all size 25/.04 were subjected to rotational bending at the curvature of 35° and 45° in air at the temperature of 23° ± 2°C, and the number of revolutions to fracture (N(f)) was recorded. The fracture surface of all fragments was examined by a scanning electron microscope. The crack-initiation sites, the percentage of dimple area to the whole fracture cross-section, and the surface strain amplitude (ε(a)) were noted. The new alloy yielded an improvement of over three to eight times in N(f) of CM files than that of conventional NiTi files (P wire (58%-100%) had one crack origin. The values of the fraction area occupied by the dimple region were significantly smaller on CM NiTi instruments compared with conventional NiTi instruments (P wire at both curvatures (P Wire had a significantly higher N(f) and lower surface strain amplitude than the conventional NiTi wire files with identical design. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

49 CFR 572.200 - Instrumentation and test conditions.

Science.gov (United States)

2010-10-01

... TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES IIsD... Test, unless noted otherwise. (g) All instrumented response signal measurements shall be treated to the... conform to the Sign Convention For Vehicle Crash Testing, Surface Vehicle Information Report, SAE J1733...

Instrumentation for the follow-up of severe accidents

International Nuclear Information System (INIS)

Munoz Sanchez, A.; Nino Perote, R.

2000-01-01

During severe accidents, it is foreseeable that the instrumentation installed in a plant is subjected to conditions which are more hostile than those for which the instrumentation was designed and qualified. Moreover, new, specific instrumentation is required to monitor variables which have not been considered until now, and to control systems which lessen the consequences of severe accidents. Both existing instrumentation used to monitor critical functions in design basis accident conditions and additional instrumentation which provides the information necessary to control and mitigate the consequences of severe accidents, have to be designed to withstand such conditions, especially in terms of measurements range, functional characteristics and qualification to withstand pressure and temperature loads resulting from steam explosion, hydrogen combustion/explosion and high levels of radiation over long periods of time. (Author)

Fusion instrumentation and control: a development strategy

International Nuclear Information System (INIS)

Hsu, P.Y.; Greninger, R.C.; Longhurst, G.R.; Madden, P.

1981-01-01

We have examined requirements for a fusion instrumentation and control development program to determine where emphasis is needed. The complex, fast, and closely coupled system dynamics of fusion reactors reveal a need for a rigorous approach to the development of instrumentation and control systems. A framework for such a development program should concentrate on three principal need areas: the operator-machine interface, the data and control system architecture, and fusion compatible instruments and sensors. System dynamics characterization of the whole fusion reactor system is also needed to facilitate the implementation process in each of these areas. Finally, the future need to make the instrumentation and control system compatible with the requirements of a commercial plant is met by applying transition technology. These needs form the basis for the program tasks suggested

Instrumental neutron activation analysis - a routine method

International Nuclear Information System (INIS)

Bruin, M. de.

1983-01-01

This thesis describes the way in which at IRI instrumental neutron activation analysis (INAA) has been developed into an automated system for routine analysis. The basis of this work are 20 publications describing the development of INAA since 1968. (Auth.)

Highly stable single-crystal LaB6 cathode for conventional electron microprobe instruments

International Nuclear Information System (INIS)

Shimizu, R.; Shinike, T.; Ichimura, S.; Kawaii, S.; Tanaka, T.

1978-01-01

The performance of single-crystal LaB 6 cathode was examined by measuring the brightness and current stability under the same conditions as for the conventional W hairpin cathode. The LaB 6 cathode was mounted in Vogel-type electron gun assembly of an electron probe microanalyser JAX-3 specifically modified for this purpose. The result shows that the present LaB 6 cathode provides not only high brightness of 2 x 10 5 A/cm 2 str. at 20 kV, but also high-current stability better than 1 x 10 - 3 Ah - 1 in standard operation without any specific aid for current stabilization. Thus an order of magnitude increase in both the brightness and service lifetime can easily be obtained provided that the vacuum of the system is adequate, namely better than 1 x 10 - 5 Torr (1.33 x 10 - 3 Pa). This substantial improvement of the present single-crystal LaB 6 cathode over the conventional W hairpin was also confirmed in a practical way by use in a commercial-type scanning Auger electron microscope, JAMP III

Network externality perspective of feed-in-tariffs (FIT) instruments-Some observations and suggestions

International Nuclear Information System (INIS)

Shum, Kwok L.; Watanabe, Chihiro

2010-01-01

Existing energy policy frameworks revolving around the acceleration of deployment of renewable energy technology can be broadly classified as the quantity vs. price approach. With this brief viewpoint, this paper suggests another perspective of viewing these instruments in terms of a more fundamental basis: whether the deployment in capacity is in terms of a cost minimization approach or a network externality approach. We suggest that the generic price or feed in tariff (FIT) approach in subsidizing renewable electricity generation and associated income would create a bandwagon or self-propagation effect among users rendering the renewable energy technology spreads like a software or information technology. Our objective is to raise awareness of this technology dynamics oriented perspective in renewable deployment supplementing the conventional installation subsidies perspective. We hope that it would inspire more empirical works and studies relating to the policy implications of this viewpoint.

The nuclear instrumentation system of the French 1400 MWe reactors

International Nuclear Information System (INIS)

Bourgerette, A.; Mauduit, J.P.

1993-01-01

The nuclear instrumentation systems in power reactors in France have made considerable advances thanks to technological progress. The appearance of an integrated digital protection system (SPIN) and the extension of digital techniques have considerably improved performance and operating flexibility. Working on the basis of technology developed jointly with the Nuclear Electronics and Instrumentation Department at the French Atomic Energy Commission (CEA), Framatome and Merlin Gerin have designed the new nuclear instrumentation system for 1400 MW reactors. (authors). 4 figs

The Paris Convention for the prevention of marine pollution from land-based sources

International Nuclear Information System (INIS)

Dinkloh, L.; Braun, H.

1983-01-01

The Paris Convention of 1974 which entered into force at an international level in 1978 is an important instrument to protect the North Sea and the North Atlantic against pollution from land-based sources. Contracting Parties are practically all riparian states of its scope of application - 13 states on the whole - as well as the EC. There is a survey of the functions, organization and working method, the instruments and results so far achieved in the framework of the Convention. Priority was so far given to the following substances or, respectively, groups of substances: oil, mercury, cadmium, drines, PCB's and PCT's as well as titanium dioxide. In this respect, it was above all agreed on: emission and immission standards (or guide values, respectively), recommendations for measures reducing emissions and a number of obligations to report. Studies and discussions on organosilicone compounds, radioactivity, water pollution through the atmosphere and eutrophication phenomena are relatively new. The opportunities offered by the Paris Convention have not yet been fully used. (orig.) [de

Musical instruments in the 21st century identities, configurations, practices

CERN Document Server

Campo, Alberto; Egermann, Hauke; Hardjowirogo, Sarah-Indriyati; Weinzierl, Stefan

2017-01-01

By exploring the many different types and forms of contemporary musical instruments, this book contributes to a better understanding of the conditions of instrumentality in the 21st century. Providing insights from science, humanities and the arts, authors from a wide range of disciplines discuss the following questions: · What are the conditions under which an object is recognized as a musical instrument? · What are the actions and procedures typically associated with musical instruments? · What kind of (mental and physical) knowledge do we access in order to recognize or use something as a musical instrument? · How is this knowledge being shaped by cultural conventions and temporal conditions? · How do algorithmic processes 'change the game' of musical performance, and as a result, how do they affect notions of instrumentality? · How do we address the question of instrumental identity within an instrument's design process? · What properties can be used to differentiate successful and unsuccessful ins...

Quasisymmetry equations for conventional stellarators

International Nuclear Information System (INIS)

Pustovitov, V.D.

1994-11-01

General quasisymmetry condition, which demands the independence of B 2 on one of the angular Boozer coordinates, is reduced to two equations containing only geometrical characteristics and helical field of a stellarator. The analysis is performed for conventional stellarators with a planar circular axis using standard stellarator expansion. As a basis, the invariant quasisymmetry condition is used. The quasisymmetry equations for stellarators are obtained from this condition also in an invariant form. Simplified analogs of these equations are given for the case when averaged magnetic surfaces are circular shifted torii. It is shown that quasisymmetry condition can be satisfied, in principle, in a conventional stellarator by a proper choice of two satellite harmonics of the helical field in addition to the main harmonic. Besides, there appears a restriction on the shift of magnetic surfaces. Thus, in general, the problem is closely related with that of self-consistent description of a configuration. (author)

Data, instruments, and theory a dialectical approach to understanding science

CERN Document Server

Ackermann, Robert John

1985-01-01

Robert John Ackermann deals decisively with the problem of relativism that has plagued post-empiricist philosophy of science. Recognizing that theory and data are mediated by data domains (bordered data sets produced by scientific instruments), he argues that the use of instruments breaks the dependency of observation on theory and thus creates a reasoned basis for scientific objectivity.

Navigated versus conventional total knee arthroplasty: A prospective study at three years follow-up.

Science.gov (United States)

Martín-Hernández, C; Sanz-Sainz, M; Revenga-Giertych, C; Hernández-Vaquero, D; Fernández-Carreira, J M; Albareda-Albareda, J; Castillo-Palacios, A; Ranera-Garcia, M

2018-03-28

Computer-assisted surgery application in total knee arthroplasty (TKA) has shown more accurate implant alignment compared with conventional instrumentation and is associated with more homogeneous alignment results. Although longer implant survival and superior clinical outcomes should be expected from navigated TKA, currently available evidence does not support this hypothesis. The aim of this study was to compare navigated TKA with conventional TKA regarding clinical and radiological outcomes after a 3-year follow-up under the hypothesis that navigated TKA would provide better outcomes than conventional TKA. In a prospective multicentre study, 119 patients underwent navigated TKA and 80 patients received conventional instrumentation. Patients were evaluated at the baseline and at postoperative months 3, 12, 24, and 36. Analysis included the American Knee Society Score (KSS), Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), Short Form-12 (SF12) Health Survey, and radiographic assessment. All clinical scores improved significantly for all patients during the follow-up but were significantly better in the navigation group. The percentage of patients showing a mechanical axis between 3° of varus and 3° of valgus was significantly higher in the ATR group (93%) than in the conventional TKA group (71%) (P<.01). The use of computer-assisted surgery in TKA provides more accurate mechanical alignment and superior short-term functional outcomes compared to conventional TKA. Copyright © 2018 SECOT. Publicado por Elsevier España, S.L.U. All rights reserved.

Nuclear instrument maintenance - problems, solutions, and obstacles

International Nuclear Information System (INIS)

Vuister, P.H.

1983-01-01

In 200 laboratories of South-East Asia, Latin America and Africa a survey was made of the state of instrumentation for nuclear medicine. The principal cause of failures and defects was inadequate quality control and preventive maintenance. On the basis of the survey coordinated research programs were compiled for the maintenance of nuclear instruments. The four principal points of the programs are: to safeguard quality and stable electric power supplies for the instruments, to safeguard permanent temperature and humidity in the environment in which the equipment is operated, effective maintenance, and training of personnel. In the years 1981 and 1982, 14 local training courses were run in which emphasis was put on practicals and tests in mechanics and electronics

An instrument for X-ray set quality assurance measurements

International Nuclear Information System (INIS)

Willetts, R.J.; West, M.B.; Brydon, J.

1989-01-01

This paper describes a prototype electronic instrument for performing quality assurance (QA) measurements on diagnostic radiological equipment with a view to long-term performance assessment on a Regional basis. The instrument is based on a Tandy 200 laptop computer and has been developed primarily to include the assessment of image intensifier/TV systems in a general QA package. It is capable of accepting signals from the following sources: (1) a radiation detector (diode array); (2) a Keithley kV divider (Keithley Instruments, Inc.); (3) the video output of an image intensifier system. (author)

Environmental Testing for Precision Parts and Instruments

International Nuclear Information System (INIS)

Choi, Man Yong; Park, Jeong Hak; Yun, Kyu Tek

2001-01-01

Precision parts and instruments are tested to evaluate performance in development-process and product-step to prement a potential defect due to a failure design. In this paper, Environmental test technology, which is the basis of reliability analysis, is introduced with examples of test criterion, test method for products, encoder and traffic signal controller, and measuring instruments. Recently, as the importance of the environmental test technology is recognised. It is proposed that training of test technician and technology of jig design and failure analysis are very essential

Design of coordinated controller in nuclear power plant based on digital instrument and control technology

International Nuclear Information System (INIS)

Cheng Shouyu; Peng Minjun; Liu Xinkai; Zhao Qiang; Deng Xiangxin

2014-01-01

Nuclear power plant (NPP) is a multi-input and multi-output, no-linear and time-varying complex system. The conventional PID controller is usually used in NPP control system which is based on analog instrument. The system parameters are easy to overshoot and the response time is longer in the control mode of the conventional PID. In order to improve this condition, a new coordinated control strategy which is based on expert system and the original controllers in the digital instrument and control technology was presented. In order to verify and validate it, the proposed coordinated control technology was tested by the full-scope real-time simulation system. The results prove that using digital instrument and control technology to achieve coordinated controller is feasible, the coordinated controller can effectively improve the dynamic operating characteristics of the system, and the coordinated controller is superior to the conventional PID controller in control performance. (authors)

A prompt start: Implementing the framework convention on climate change

International Nuclear Information System (INIS)

Chayes, A.; Skolnikoff, E.B.; Victor, D.G.

1992-01-01

A Framework Convention on Climate Change is under active negotiation in the United Nations with the expectation it will be ready for Signature at the Rio Conference this June. Under the most optimistic projections, a Convention will not come into force and be an effective instrument for months, probably years. In recognition of the several institutional tasks that will be of crucial importance whatever the detailed content of the Convention a small group of high international organizations involved in the negotiations was convened at the Rockefeller Foundation's Conference Center at Bellagio in January. The discussions at Bellagio on the need for a Prompt Start on these institutional tasks benefitted from earlier meetings at Harvard in March and at Bermuda in May, 1991, that the co-organizers convened to discuss these and related aspects of the negotiations on a Climate Convention. Those meetings were attended by members of the academic community, officials from the United Nations, and representatives of governments involved in the negotiations

Developments in international convention on nuclear third party liability

International Nuclear Information System (INIS)

Reyners, P.

2000-01-01

A few years after the adoption of a Protocol to amend the world-wide Vienna Convention on Civil Liability for Nuclear Damage and of a new ''global'' Convention on the Supplementary Compensation of Nuclear Damage (September 1997), the countries which are party to the Western Europe based Paris and Brussels Conventions are working on the revision of these instruments within the OECD Nuclear Energy Agency. The objective of this exercise is not only to preserve the compatibility of the Paris and Vienna provisions, which is now an imperative deriving from the application of the 1988 Joint Protocol linking these two Conventions, but also to substantially improve certain features of this regime such as its technical and geographical scope of application, the facilitation of the rights of victims to defend their claims and, of course, the level of funds effectively available to compensate the damage. This paper reviews briefly the recent evolution of the international nuclear liability regime and discusses some of the challenges which the nuclear countries are facing in this context. (author)

Study of the performance of diagnostic radiology instruments during calibration

International Nuclear Information System (INIS)

Freitas, Rodrigo N. de; Vivolo, Vitor; Potiens, Maria da Penha A.

2008-01-01

Full text: The instruments used in diagnostic radiology measurements represent 8 % of the tested instruments by the calibration laboratory of IPEN annually (approximately 1600 in 2007). Considering that the calibration of this kind of instrument is performed biannually it is possible to conclude that almost 300 instruments are being used to measure the air kerma in diagnostic radiology clinics to determine the in beam values (in front of the patient), attenuated measurements (behind the patient) and scattered radiation. This work presents the results of the calibration of the instruments used in mammography, computed tomography, dental and conventional diagnostic radiology dosimetry, performed during the period of 2005 to 2007. Their performances during the calibrations measurements were evaluated. Although at the calibration laboratory there are three available series of radiation quality to this type of calibration (RQR, N and M, according to standards IEC 61267 and ISO 4037-1.), the applications can be assorted (general radiology, computed tomography, mammography, radiation protection and fluoroscopy). Depending on its design and behaviour , one kind of instrument can be used for one or more type of applications. The instruments normally used for diagnostic radiology measurements are ionization chambers with volumes varying from 3 to 1800 cm 3 , and can be cylindrical, spherical or plane parallel plates kind. They usually are sensitive to photon particles, with energies greater than 15 keV and can be used up to 1200 keV. In this work they were tested in X radiation fields from 25 to 150 kV, in specific qualities depending on the utilization of the instrument. The calibration results of 390 instruments received from 2005 to 2007 were analyzed. About 20 instruments were not able to be calibrated due to bad functioning. The calibration coefficients obtained were between 0.88 and 1.24. The uncertainties were always less than ± 3.6% to instruments used in scattered

Approaching the basis set limit for DFT calculations using an environment-adapted minimal basis with perturbation theory: Formulation, proof of concept, and a pilot implementation

International Nuclear Information System (INIS)

Mao, Yuezhi; Horn, Paul R.; Mardirossian, Narbe; Head-Gordon, Teresa; Skylaris, Chris-Kriton; Head-Gordon, Martin

2016-01-01

Recently developed density functionals have good accuracy for both thermochemistry (TC) and non-covalent interactions (NC) if very large atomic orbital basis sets are used. To approach the basis set limit with potentially lower computational cost, a new self-consistent field (SCF) scheme is presented that employs minimal adaptive basis (MAB) functions. The MAB functions are optimized on each atomic site by minimizing a surrogate function. High accuracy is obtained by applying a perturbative correction (PC) to the MAB calculation, similar to dual basis approaches. Compared to exact SCF results, using this MAB-SCF (PC) approach with the same large target basis set produces <0.15 kcal/mol root-mean-square deviations for most of the tested TC datasets, and <0.1 kcal/mol for most of the NC datasets. The performance of density functionals near the basis set limit can be even better reproduced. With further improvement to its implementation, MAB-SCF (PC) is a promising lower-cost substitute for conventional large-basis calculations as a method to approach the basis set limit of modern density functionals.

The law as an instrument of technology control and as a basis for technological development

International Nuclear Information System (INIS)

Kloepfer, M.

1998-01-01

In public debates about German industry's global competitiveness it becomes evident that environmental law and the technology-related law are almost exclusively perceived as systems of law which - for reasons of environmental protection and protection of public health - are setting restraints to technological development. This is a narrow perspective neglecting the functions of the law as an instrument providing legal security and a reliable framework for developments. In a democratic, constitutional state, the environmental law and the technology-related law are instruments providing for protection of the basic, general rights and requirements of technology, and contribute to ensuring general acceptance of technologic development. (orig./CB) [de

UPTF test instrumentation. Measurement system identification, engineering units and computed parameters

International Nuclear Information System (INIS)

Sarkar, J.; Liebert, J.; Laeufer, R.

1992-11-01

This updated version of the previous report /1/ contains, besides additional instrumentation needed for 2D/3D Programme, the supplementary instrumentation in the inlet plenum of SG simulator and hot and cold leg of broken loop, the cold leg of intact loops and the upper plenum to meet the requirements (Test Phase A) of the UPTF Programme, TRAM, sponsored by the Federal Minister of Research and Technology (BMFT) of the Federal Republic of Germany. For understanding, the derivation and the description of the identification codes for the entire conventional and advanced measurement systems classifying the function, and the equipment unit, key, as adopted in the conventional power plants, have been included. Amendments have also been made to the appendices. In particular, the list of measurement systems covering the measurement identification code, instrument, measured quantity, measuring range, band width, uncertainty and sensor location has been updated and extended to include the supplementary instrumentation. Beyond these amendments, the uncertainties of measurements have been precisely specified. The measurement identification codes which also stand for the identification of the corresponding measured quantities in engineering units and the identification codes derived therefrom for the computed parameters have been adequately detailed. (orig.)

Comparison of retreatment ability of full-sequence reciprocating instrumentation and 360° rotary instrumentation.

Science.gov (United States)

Capar, Ismail Davut; Gok, Tuba; Orhan, Ezgi

2015-12-01

The purpose of the present study was to investigate the amount of root canal filling material after root canal filling removal with 360° rotary instrumentation or reciprocating motion with the same file sequence. Root canals of the 36 mandibular premolars were shaped with ProTaper Universal instruments up to size F2 and filled with corresponding single gutta-percha cone and sealer. The teeth were assigned to two retreatment groups (n = 18): group 1 360° rotational motion and group 2 reciprocating motion of ATR Tecnika motors (1310° clockwise and 578° counterclockwise). Retreatment procedure was performed with ProTaper Universal retreatment files with a sequence of D1-3 and ProTaper Universal F3 instruments. Total time required to remove filling material were recorded. Remaining filling material was examined under stereomicroscope at ×8 magnification. The data were analysed statistically using the Mann-Whitney U test, and testing was performed at 95 % confidence level (p  0.05) in terms of remaining filling material. The total time required for retreatment was shorter in 360° rotational motion group compared to reciprocating motion group (p instruments with reciprocating motion of ATR motor and conventional rotary motion have similar efficacy in root canal filling removal.

Draft bill relating to the IAEA convention of September 26, 1986, on early notification of nuclear accident, and on mutual assistance in care of nuclear accident or radiological emergency (IAEA Conventions on notification and on assistance)

International Nuclear Information System (INIS)

1989-01-01

The purpose of the two Conventions signed in Vienna on Sept. 26, 1986, is to support and improve international cooperation in case of a nuclear accident or a radiological emergency probably involving transfrontier contamination, and to provide the necessary legal framework for cooperation and assistance, as well as a basis for an information system. The bill presented by the Federal Government creates the legal basis for ratification of the Conventions in compliance with Art. 59, paragraph 2, first sentence of the Basic Law. Majority decision. (orig./HP) [de

A smart rotary technique versus conventional pulpectomy for primary teeth: A randomized controlled clinical study.

Science.gov (United States)

Mokhtari, Negar; Shirazi, Alireza-Sarraf; Ebrahimi, Masoumeh

2017-11-01

Techniques with adequate accuracy of working length determination along with shorter duration of treatment in pulpectomy procedure seems to be essential in pediatric dentistry. The aim of the present study was to evaluate the accuracy of root canal length measurement with Root ZX II apex locator and rotary system in pulpectomy of primary teeth. In this randomized control clinical trial complete pulpectomy was performed on 80 mandibular primary molars in 80, 4-6-year-old children. The study population was randomly divided into case and control groups. In control group conventional pulpectomy was performed and in the case group working length was determined by electronic apex locator Root ZXII and instrumented with Mtwo rotary files. Statistical evaluation was performed using Mann-Whitney and Chi-Square tests ( P <0.05). There were no significant differences between electronic apex locator Root ZXII and conventional method in accuracy of root canal length determination. However significantly less time was needed for instrumenting with rotary files ( P =0.000). Considering the comparable results in accuracy of root canal length determination and the considerably shorter instrumentation time in Root ZXII apex locator and rotary system, it may be suggested for pulpectomy in primary molar teeth. Key words: Rotary technique, conventional technique, pulpectomy, primary teeth.

INTUITION AS A BASIS FOR LEADERSHIP: PSYCHOLOGICAL AND STATISTICAL MEASUREMENT INSTRUMENTS

Directory of Open Access Journals (Sweden)

Daniela BELU

2012-01-01

Full Text Available The aim of this paper is to overview a set of research results concerning the influence a person may have on others by simply using leadership skills. The premise underlying the endeavor is that, in the end, intuition is a basis for leadership. Based on the findings, the definition for leadership suggested by this article runs as follows: the harmony between what one thinks and does. Moreover, the article proposes that this harmony be taught through distinct subject matters at undergraduate level for those who are to obtain a diploma in “organizational management”.

Novelties introduced by the Council of Europe Convention on preventing and combating violence against women and domestic violence

Directory of Open Access Journals (Sweden)

Kovaček-Stanić Gordana

2014-01-01

Full Text Available Violence as a phenomenon inherent to man, from the outset, can be manifested in different forms. According to statistics, the number of women who have suffered some form of violence is disturbingly great. Domestic violence and violence against women is a serious problem on which work on an international level has recently began. Some international organizations indirectly dealt with this issue in instruments which refer to the protection of human rights. At the European level, in 2011, the Convention of the Council of Europe (so-called Istanbul Convention, was adopted which was the first legally binding instrument on the European continent, that deals with the prevention of violence against women, protection of them and punishing the perpetrators. The Convention entered into force in 2014, and Serbia is one of the countries that have ratified this Convention. This paper aims to presents novelties that will be brought to the domestic legal system by this convention, with simultaneous analysis of the situation in Montenegro, where in 2010 the Law on Protection against Domestic Violence was enacted.

Validation of Reverse-Engineered and Additive-Manufactured Microsurgical Instrument Prototype.

Science.gov (United States)

Singh, Ramandeep; Suri, Ashish; Anand, Sneh; Baby, Britty

2016-12-01

With advancements in imaging techniques, neurosurgical procedures are becoming highly precise and minimally invasive, thus demanding development of new ergonomically aesthetic instruments. Conventionally, neurosurgical instruments are manufactured using subtractive manufacturing methods. Such a process is complex, time-consuming, and impractical for prototype development and validation of new designs. Therefore, an alternative design process has been used utilizing blue light scanning, computer-aided designing, and additive manufacturing direct metal laser sintering (DMLS) for microsurgical instrument prototype development. Deviations of DMLS-fabricated instrument were studied by superimposing scan data of fabricated instrument with the computer-aided designing model. Content and concurrent validity of the fabricated prototypes was done by a group of 15 neurosurgeons by performing sciatic nerve anastomosis in small laboratory animals. Comparative scoring was obtained for the control and study instrument. T test was applied to the individual parameters and P values for force (P direct application of these additive-manufactured instruments in the operating room requires further validation. © The Author(s) 2016.

Conventional armed forces in Europe: Technology scenario development

Energy Technology Data Exchange (ETDEWEB)

Houser, G.M.

1990-07-01

In January 1986, the Soviet Union's Mikhail Gorbachev proposed elimination of all nuclear weapons by the year 2000. In April of that year, Mr. Gorbachev proposed substantial reductions of conventional weapons in Europe, from the Atlantic Ocean to the Ural Mountains, including reductions in operational-tactical nuclear weapons. In May 1986, the North Atlantic Treaty Organization (NATO) responded with the Brussels Declaration on Conventional Arms Control,'' which indicated readiness to open East/West discussions on establishing a mandate for negotiating conventional arms control throughout Europe. The Group of 23,'' which met in Vienna beginning in February 1987, concluded the meeting in January 1989 with a mandate for the Conventional Armed Forced in Europe (CFE) negotiations. On 6 March 1989, CFE talks began, and these talks have continued through six rounds (as of April 1990). Although US President George Bush, on 30 May 1989, called for agreement within six months to a year, and the Malta meeting of December 1989 called for completion of a CFE agreement by the end of 1990, much remains to be negotiated. This report provides three types of information. First, treaty provisions brought to the table by both sides are compared. Second, on the basis of these provisions, problem areas for each of the provision elements are postulated and possible scenarios for resolving these problem areas are developed. Third, the scenarios are used as requirements for tasks assigned program elements for possible US implementation of a CFE treaty. As progress is achieved during the negotiations, this report could be updated, as necessary, in each of the areas to provide a continuing systematic basis for program implementation and technology development. 8 refs.

Technical Basis for Implementation of the PCM-1B for Personnel Release at Tank Farms

International Nuclear Information System (INIS)

BROWN, R.L.

1999-01-01

The purpose of this document is to define the technical basis and implementing guidelines for using automated personnel contamination monitors, such as the PCM-1B, at the River Protection Project (RPP) in lieu of performing a hand-held instrument followed by a PCM-1B survey for personnel release from contamination areas requiring a beta-gamma whole body survey. This document provides the basis for full implementation of the PCM-1B release survey, without the supplemental hand and foot survey, as currently implemented at RPP. This document applies only to RPP facilities. This document does not provide the technical basis for determining the equivalency of an automated system to hand-held instruments, or to the effective counting capability of automated systems as such technical determinations are contained in TBTN: GDGH-9604-RLS-0015

Overview: Field instrumentation - A Mikado's dream

International Nuclear Information System (INIS)

Spittler, T.M.

1992-01-01

The Mikado of Gilbert ampersand Sullivan fame held out as an open-quotes object all sublimeclose quotes which he hoped to open-quotes achieve in timeclose quotes the fitting of the punishment to the crime. Like that potentate, I too have long held the hope of finding instrumentation which is ideally suited to measurement of environmental contaminants in the field. Today, at least one of us has had that dream fulfilled. For years, those of us interested in field analysis have had to apply time consuming and cumbersome methods to relatively simple and often short-term environmental measurement problems. Meanwhile, we watched the literature and perused the product blurbs in hopes of finding the ideal tools for on-site, real time analysis. Of course, that search will always go forward as better instruments are developed. Today we can finally point to many pieces of equipment that are on the market and which provide high quality data in real time for a number of the most important environmental contaminants. Furthermore, the sensitivity of some of these field instruments exceeds that of conventional lab instrumentation. Coupled with innovative techniques for sample preparation and proper quality control, field instrumentation can often go a long way to solving problems in rapid detection, quantitation, and positive identification

The Ad Hoc process to strengthen the framework convention on climate change

Energy Technology Data Exchange (ETDEWEB)

Ramakrishna, K.; Deutz, A.M.; Jacobsen, L.A. [eds.

1995-11-01

The Woods Hole Research Center convened an International Conference on The Ad Hoc Process to Strengthen the Framework Convention on Climate Change in Woods Hole, MA, on October 7-9, 1995. The conference was conducted to examine the prospects for successful adoption of a protocol to the Framework Convention on Climate Change by 1997. In preparation for the Second session of the Ad Hoc Group on the Berlin Mandate, several governmental and nongovernmental representatives met in Woods Hole to discuss the process and possible outcome of the Berlin Mandate negotiations for a protocol or other legal instrument to strengthen the Convention. The conference was by invitation and all participants attended in their personal capacities.

Standardization of portable assay instrumentation: the neutron-coincidence tree

International Nuclear Information System (INIS)

Menlove, H.O.

1983-01-01

Standardization of portable neutron assay instrumentation has been achieved by using the neutron coincidence technique as a common basis for a wide range of instruments and applications. The electronics originally developed for the High-Level Neutron Coincidence Counter has been adapted to both passive- and active-assay instrumentation for field verification of bulk plutonium, inventory samples, pellets, powders, nitrates, high-enriched uranium, and materials-testing-reactor, light-water-reactor, and mixed-oxide fuel assemblies. The family of detectors developed at Los Alamos National Laboratory and their performance under in-field conditions are described. 16 figures, 3 tables

Reflections on a future international convention on safety in radioactive waste management - September 1994

International Nuclear Information System (INIS)

Arias Canete, A.

1995-01-01

This probably is a suitable moment for work to begin on an international Convention in this area, although it is a difficult task. Generally speaking, the RADWASS (Radioactive Waste Safety Standards) Programme has achieved sufficient consensus, and might serve as an important basis for work in relation to the Convention. The Convention should not go into highly technical details since consensus at this level is more difficult at the present moment, although this will undoubtedly be achieved in the medium term. An important element of the Convention should be the regulation of movements of radioactive wastes at international level. (orig./HP)

Optimising the effect of policy instruments

DEFF Research Database (Denmark)

Pedersen, Anders Branth; Nielsen, Helle Ørsted; Christensen, Tove

2012-01-01

Economic modelling generally assumes that businesses are profit maximisers. However, behavioural economics holds that businesses pursue multiple objectives and may even sacrifice some profit. This has implications for the effectiveness of incentive-based environmental policies. Using Danish farme...... to policy instruments; farmers who focus on yield indicate less responsiveness to economic policy instruments. The results imply that it is important to implement a broad array of policy instruments to match different farmer rationales.......Economic modelling generally assumes that businesses are profit maximisers. However, behavioural economics holds that businesses pursue multiple objectives and may even sacrifice some profit. This has implications for the effectiveness of incentive-based environmental policies. Using Danish farmers...... as a case, this paper examines whether non-economic rationales may trump economic ones in farmer decisions, and, unlike previous research, we quantify how widespread non-economic values are compared to more economic values. Data derive from a survey (1164 responses) of Danish conventional farmers' decision...

netherland hydrological modeling instrument

Science.gov (United States)

Hoogewoud, J. C.; de Lange, W. J.; Veldhuizen, A.; Prinsen, G.

2012-04-01

Netherlands Hydrological Modeling Instrument A decision support system for water basin management. J.C. Hoogewoud , W.J. de Lange ,A. Veldhuizen , G. Prinsen , The Netherlands Hydrological modeling Instrument (NHI) is the center point of a framework of models, to coherently model the hydrological system and the multitude of functions it supports. Dutch hydrological institutes Deltares, Alterra, Netherlands Environmental Assessment Agency, RWS Waterdienst, STOWA and Vewin are cooperating in enhancing the NHI for adequate decision support. The instrument is used by three different ministries involved in national water policy matters, for instance the WFD, drought management, manure policy and climate change issues. The basis of the modeling instrument is a state-of-the-art on-line coupling of the groundwater system (MODFLOW), the unsaturated zone (metaSWAP) and the surface water system (MOZART-DM). It brings together hydro(geo)logical processes from the column to the basin scale, ranging from 250x250m plots to the river Rhine and includes salt water flow. The NHI is validated with an eight year run (1998-2006) with dry and wet periods. For this run different parts of the hydrology have been compared with measurements. For instance, water demands in dry periods (e.g. for irrigation), discharges at outlets, groundwater levels and evaporation. A validation alone is not enough to get support from stakeholders. Involvement from stakeholders in the modeling process is needed. There fore to gain sufficient support and trust in the instrument on different (policy) levels a couple of actions have been taken: 1. a transparent evaluation of modeling-results has been set up 2. an extensive program is running to cooperate with regional waterboards and suppliers of drinking water in improving the NHI 3. sharing (hydrological) data via newly setup Modeling Database for local and national models 4. Enhancing the NHI with "local" information. The NHI is and has been used for many

[work motivation -- assessment instruments and their relevance for medical care].

Science.gov (United States)

Fiedler, Rolf G; Ranft, Andreas; Greitemann, Bernhard; Heuft, Gereon

2005-11-01

The relevance of work motivation for medical research and healthcare, in particular rehabilitation, is described. Four diagnostic instruments in the German language are introduced which can assess work motivation using a scale system: AVEM, JDS, LMI and FBTM. Their possible application and potential usage for the clinical area are discussed. Apart from the FBTM, none of these instruments can be directly used as a general instrument in a normal medical clinical setting. Finally, a current model for work motivation (compensatory model of work motivation and volition) is presented that contains basis concepts, which are judged as important for future research questions concerning the development of motivation diagnostic instruments.

How To Control Color Appearance With Instrumentation

Science.gov (United States)

Burns, Margaret E.

1980-05-01

Colorimetry, as defined by the International Commission on Illumination, is the measurement of colors, made possible by the properties of the eye and based on a set of conventions. Instrumentation for measuring object color, therefore, must be based on a human observer. The intent is to design an instrument that in effect responds as a person would, so that research development, production control and quality control areas have some means of assessing the acceptability of the appearance of a product. Investigations of a human observer's psychological response to color, and the manner in which visual observations are made, give the instrument designer and manufacturer data necessary to answer two questions: a. How can we put numbers (instrument read-out) on a perception that occurs in the brain of the observer? b. What can we learn from examination of a visual observing situation that will guide us in our design of an instrumental simulation of this situation? Involving as it does our own daily, almost unconscious, practice of making judgments concerning the things we see, the design and manufacture of color measurement instruments is an exceedingly interesting field. The advances being made concurrently today in research concerning human color vision and in optical and electronic technology will make possible increasingly useful instrumentation for quality control of product color.

Metallurgical characterization of a new nickel-titanium wire for rotary endodontic instruments.

Science.gov (United States)

Alapati, Satish B; Brantley, William A; Iijima, Masahiro; Clark, William A T; Kovarik, Libor; Buie, Caesar; Liu, Jie; Ben Johnson, William

2009-11-01

A novel thermomechanical processing procedure has been developed that yields a superelastic (SE) nickel-titanium (NiTi) wire (M-Wire) that laboratory testing shows has improved mechanical properties compared with conventional SE austenitic NiTi wires used for manufacture of rotary instruments. The objective of this study was to determine the origin of the improved mechanical properties. Specimens from 2 batches of M-Wire prepared under different processing conditions and from 1 batch of standard-processed SE wire for rotary instruments were examined by scanning transmission electron microscopy, temperature-modulated differential scanning calorimetry, micro-x-ray diffraction, and scanning electron microscopy with x-ray energy-dispersive spectrometric analyses. The processing for M-Wire yields a microstructure containing martensite, that the proportions of NiTi phases depend on processing conditions, and that the microstructure exhibits pronounced evidence of alloy strengthening. The presence of Ti(2)Ni precipitates in both microstructures indicates that M-Wire and the conventional SE wire for rotary instruments are titanium-rich.

Software for simulation and design of neutron scattering instrumentation

DEFF Research Database (Denmark)

Bertelsen, Mads

designed using the software. The Union components uses a new approach to simulation of samples in McStas. The properties of a sample are split into geometrical and material, simplifying user input, and allowing the construction of complicated geometries such as sample environments. Multiple scattering...... from conventional choices. Simulation of neutron scattering instrumentation is used when designing instrumentation, but also to understand instrumental effects on the measured scattering data. The Monte Carlo ray-tracing package McStas is among the most popular, capable of simulating the path of each...... neutron through the instrument using an easy to learn language. The subject of the defended thesis is contributions to the McStas language in the form of the software package guide_bot and the Union components.The guide_bot package simplifies the process of optimizing neutron guides by writing the Mc...

Aarhus and Espoo Conventions: The role in promoting effective public participation in nuclear decision-making. The role of the Aarhus and Espoo Conventions in promoting effective public participation in nuclear decision-making

International Nuclear Information System (INIS)

Yanush, Maryna; Jendroska, Jerzy

2017-01-01

Ms Yanush and Mr Jendroska highlighted the role and importance of the Convention on Access to Information, Public Participation in Decision-Making and Access to Justice in Environmental Matters (the Aarhus Convention) and that of the Convention on Environmental Impact Assessment in a Transboundary Context (the Espoo Convention). These two conventions are open for global accession and, at present, have been ratified mainly by European and Central Asian countries within the United Nations Economic Commission for Europe (UNECE) region. Those two conventions, which apply to a wide range of activities including nuclear, are the only two binding international instruments setting minimum standards for public access to environmental information and public participation in decision making. The Maastricht Recommendations on Promoting Effective Public Participation in Decision-Making in Environmental Matters under the Aarhus Convention and the Good Practice Recommendations on the Application of the Convention to Nuclear Energy-related Activities under the Espoo Convention are instrumental in advancing the implementation in this area. Public participation under the Aarhus Convention goes beyond information or consultation: the decision maker must take into account the views of the 'public concerned' (i.e. the members of the public affected or likely to be affected by the decision making or having an interest in it). As the 'public concerned' is assessed through the potential impact of the proposed activity, including in the case of an accident, the obligation to notify and provide opportunity for public participation is not limited to the territory of the country hosting the proposed activity. Mr Jendroska indicated a particular finding of the Espoo Convention Implementation Committee that decisions regarding modifications, upgrades or extensions to the lifetime/operation of a nuclear installation would be subject to these obligations even though the activity remains exactly

The compatibility of flexible instruments under the Kyoto Protocol

International Nuclear Information System (INIS)

Jepma, C.J.; Van der Gaast, W.P.; Woerdman, E.

1998-01-01

The compatibility of the Kyoto Protocol flexible instruments and the lessons that can be learned form the AIJ-phase (AIJ stands for Activities Implemented Jointly) are discussed. The key point to be made is that there may be various applications of flexible instruments which can create situations where the various instruments would crowd out each other. On the other hand, applying flexible instruments may create a leverage for Parties in terms of achieving domestic environmental objectives. In addition, several issues related to the implementation of Joint Implementation (JI) , Clean Development Mechanism (CDM) and international emissions trading are discussed. The issues concern mainly those that have been included in the working programme on flexible instruments for CoP4 and CoP5 (CoP stands for Convention of Parties). As such the report discusses the consequences of possible negotiations outcomes at CoP for the effectiveness of flexible instruments, Parties' capabilities to achieve their Kyoto Protocol commitments cost-effectively, and the role of the private sector on the national and international credits markets(s). 106 refs

Balances instruments, manufacturers, history

CERN Document Server

Robens, Erich; Kiefer, Susanne

2014-01-01

The book deals mainly with direct mass determination by means of a conventional balances. It covers the history of the balance from the beginnings in Egypt earlier than 3000 BC to recent developments. All balance types are described with emphasis on scientific balances. Methods of indirect mass determination, which are applied to very light objects like molecules and the basic particles of matter and celestial bodies, are included.  As additional guidance, today’s manufacturers are listed and the profile of important companies is reviewed. Several hundred photographs, reproductions and drawings show instruments and their uses. This book includes commercial weighing instruments for merchandise and raw materials in workshops as well as symbolic weighing in the ancient Egyptian’s ceremony of ‘Weighing of the Heart’, the Greek fate balance, the Roman  Justitia, Juno Moneta and Middle Ages scenes of the Last Judgement with Jesus or St. Michael and of modern balances. The photographs are selected from the...

The Friedrich-Lively Instrument to Assess the Impact of Schizophrenia on Siblings (FLIISS): Part I--instrument construction.

Science.gov (United States)

Friedrich, Rose Marie; Lively, Sonja; Rubenstein, Linda; Buckwalter, Kathleen

2002-01-01

Siblings of persons with schizophrenia may provide primary or secondary care for their sibling and support to parents who are primary care givers. These siblings experience stress and the accompanying sequelae of decreased quality of life, grief, chronic illness, and symptoms of depression and anxiety. Comprehensive measures of sibling stress have not been published. Before interventions to help siblings can be created, health professionals need such an assessment. The Friedrich-Lively Instrument to Assess the Impact of Schizophrenia on Siblings (FLIISS) has been developed to meet the needs of both health workers and siblings. The instrument has a strong conceptual basis adapted from Pearlin's model of stress in caregiving and was preceded by pilot work that evaluated both quantitative and qualitative data. In this article, (Part I), the development of the instrument and its relationships to the conceptual model are described. Health professionals can use the instrument for collecting information that will increase their ability to identify sources of stress faced by siblings of persons with schizophrenia, and from this assessment they may develop interventions for this underserved population.

Wound healing of osteotomy defects prepared with piezo or conventional surgical instruments: a pilot study in rabbits.

Science.gov (United States)

Ma, Li; Mattheos, Nikos; Sun, Yan; Liu, Xi Ling; Yip Chui, Ying; Lang, Niklaus Peter

2015-08-01

The aim of the present study was to evaluate and compare the wound-healing process following osteotomies performed with either conventional rotary burs or piezoelectric surgery in a rabbit model. Two types of osteotomy window defects of the nasal cavities were prepared on the nasal bone of 16 adult New Zealand white rabbits with either a conventional rotary bur or piezo surgery. The defects were covered with a resorbable membrane. Four animals were killed at 1, 2, 3, and 5 weeks after the surgical procedure, respectively. Histological and morphometric evaluations were performed to assess the volumetric density of various tissue components: the blood clot, vascularized structures, provisional matrix, osteoid, mineralized bone, bone debris, residual tissue, and old bone. Significantly more bone debris was found at 1 week in the conventionally-prepared defects compared to the piezo surgically-prepared defects. At 2 and 3 weeks, a newly-formed hard tissue bridge, mainly composed of woven bone, was seen; however, no statistically-significant differences were observed. At 5 weeks, the defects were completely filled with newly-formed bone. The defects prepared by piezo surgery showed a significantly decreased proportion of bone debris at 1 week, compared to conventional rotary bur defect. © 2014 Wiley Publishing Asia Pty Ltd.

Instrument intercomparison in the high-energy mixed field at the CERN-EU reference field (CERF) facility

CERN Document Server

Caresana, Marco; Manessi, Giacomo; Ott, Klaus; Scherpelz, Robert; Silari, Marco

2014-01-01

This paper discusses an intercomparison campaign performed in the mixed radiation field at the CERN-EU (CERF) reference field facility. Various instruments were employed: conventional and extended-range rem counters including a novel instrument called LUPIN, a bubble detector using an active counting system (ABC 1260) and two tissue-equivalent proportional counters (TEPCs). The results show that the extended range instruments agree well within their uncertainties and within 1σ with the H*(10) FLUKA value. The conventional rem counters are in good agreement within their uncertainties and underestimate H*(10) as measured by the extended range instruments and as predicted by FLUKA. The TEPCs slightly overestimate the FLUKA value but they are anyhow consistent with it when taking the comparatively large total uncertainties into account, and indicate that the non-neutron part of the stray field accounts for ∼30 % of the total H*(10).

WHO FCTC as a Pioneering and Learning Instrument Comment on "The Legal Strength of International Health Instruments - What It Brings to Global Health Governance?"

Science.gov (United States)

Puska, Pekka

2017-05-23

The World Health Organization (WHO) Framework Convention on Tobacco Control (FCTC) is a unique global health instrument, since it is in the health field the only instrument that is international law. After the 10 years of its existence an Independent Expert Group assessed the impact of the FCTC using all available data and visiting a number of countries interviewing different stakeholders. It is quite clear that the Treaty has acted as a strong catalyst and framework for national actions and that remarkable progress in global tobacco control can be seen. At the same time FCTC has moved tobacco control in countries from a pure health issue to a legal responsibility of the whole government, and on the international level created stronger interagency collaboration. The assessment also showed the many challenges. The spread of tobacco use, as well as of other risk lifestyles, is related to globalization. FCTC is a pioneering example of global action to counteract the negative social consequences of globalization. A convention is not an easy instrument, but the FCTC has undoubtedly sparked thinking and development of other stronger public health instruments and of needed governance structures. © 2018 The Author(s); Published by Kerman University of Medical Sciences. This is an open-access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Maintenance of nuclear medicine instruments

Energy Technology Data Exchange (ETDEWEB)

Ambro, P

1993-12-31

Maintenance of instruments is generally of two kinds: (a) corrective maintenance, on a non-scheduled basis, to restore equipment to a functional status by repairs; (b) preventive maintenance, to keep equipment in a specified functional condition by providing systematic inspection, quality control, detection and correction of early malfunctions. Most of the instruments used in nuclear medicine are rather complex systems built from mechanical, electrical and electronic parts. Any one of these components is liable to fail at some time or other. Repair could be done only by a specialist who is able to evaluate the condition of the various parts ranging from cables to connectors, from scintillators to photomultipliers, from microprocessors to microswitches. The knowledge of the intricacies of the various electronic components required for their repairs is quite wide and varied. The electronics industry turns out more and more multi-purpose chips which can carry out the functions of many parts used in the instruments of the earlier generation. This provides protection against unauthorized copying of the circuits but it serves another purpose as well of inhibiting repairs by non-factory personnel. These trends of the instrument design should be taken into consideration when a policy has to be developed for the repairs of the hospital based equipment 1 fig., 1 tab

Maintenance of nuclear medicine instruments

International Nuclear Information System (INIS)

Ambro, P.

1992-01-01

Maintenance of instruments is generally of two kinds: (a) corrective maintenance, on a non-scheduled basis, to restore equipment to a functional status by repairs; (b) preventive maintenance, to keep equipment in a specified functional condition by providing systematic inspection, quality control, detection and correction of early malfunctions. Most of the instruments used in nuclear medicine are rather complex systems built from mechanical, electrical and electronic parts. Any one of these components is liable to fail at some time or other. Repair could be done only by a specialist who is able to evaluate the condition of the various parts ranging from cables to connectors, from scintillators to photomultipliers, from microprocessors to microswitches. The knowledge of the intricacies of the various electronic components required for their repairs is quite wide and varied. The electronics industry turns out more and more multi-purpose chips which can carry out the functions of many parts used in the instruments of the earlier generation. This provides protection against unauthorized copying of the circuits but it serves another purpose as well of inhibiting repairs by non-factory personnel. These trends of the instrument design should be taken into consideration when a policy has to be developed for the repairs of the hospital based equipment

Eroding market stability by proliferation of financial instruments

Science.gov (United States)

Caccioli, F.; Marsili, M.; Vivo, P.

2009-10-01

We contrast Arbitrage Pricing Theory (APT), the theoretical basis for the development of financial instruments, with a dynamical picture of an interacting market, in a simple setting. The proliferation of financial instruments apparently provides more means for risk diversification, making the market more efficient and complete. In the simple market of interacting traders discussed here, the proliferation of financial instruments erodes systemic stability and it drives the market to a critical state characterized by large susceptibility, strong fluctuations and enhanced correlations among risks. This suggests that the hypothesis of APT may not be compatible with a stable market dynamics. In this perspective, market stability acquires the properties of a common good, which suggests that appropriate measures should be introduced in derivative markets, to preserve stability. in here

Mechanical and Metallurgical Properties of Various Nickel-Titanium Rotary Instruments

OpenAIRE

Shim, Kyu-Sang; Oh, Soram; Kum, KeeYeon; Kim, Yu-Chan; Jee, Kwang-Koo; Chang, Seok Woo

2017-01-01

The aim of this study was to investigate the effect of thermomechanical treatment on mechanical and metallurgical properties of nickel-titanium (NiTi) rotary instruments. Eight kinds of NiTi rotary instruments with sizes of ISO #25 were selected: ProFile, K3, and One Shape for the conventional alloy; ProTaper NEXT, Reciproc, and WaveOne for the M-wire alloy; HyFlex CM for the controlled memory- (CM-) wire; and TF for the R-phase alloy. Torsional fracture and cyclic fatigue fracture tests were...

Comparison of different sets of instruments for laparoendoscopic single-site surgery in a surgical simulator with novices.

Science.gov (United States)

Wang, Dong; Shi, Long-Qing; Wang, Jing-Min; Jiang, Xiao-Hua; Ji, Zhen-Ling

2016-04-01

Given the parallel entry of working instruments through a single incision in laparoendoscopic single-site surgery, loss of triangulation in the abdominal cavity and counteracting movements of the instruments are inevitable obstacles. Some specially designed devices have emerged to ameliorate these challenges. Twenty-four novice participants were randomized into four groups using assigned instruments, conventional straight instruments, single-curved instruments, double-curved instruments and articulating instruments, respectively, to perform two basic tasks (peg transferring and pattern cutting) 14 times in a modified simulator. A test of the tasks and a resection of the intestine segment of a rat were performed. The task scores and evaluation of intraoperative skills during the resection of the intestine segment were recorded. The instrument of modified National Aeronautics and Space Administration Task Load Index (NASA-TLX) was completed. The task scores of the groups using single-curved instruments and articulating instruments were better than the other two groups on the simulator tasks, consistent with the evaluation of intraoperative skills during the resection of intestine segment. As the proficiency with the instruments increased, the task scores improved, as demonstrated by the learning curve. The workload measured by the modified NASA-TLX tool demonstrated that the groups using articulating instruments and double-curved instruments had a heavier workload in most of the categories compared with the other two groups. Single-curved and articulating instruments are more effective than conventional straight and double-curved devices, and are favourable in laparoendoscopic single-site surgery for novice learners. © 2013 Royal Australasian College of Surgeons.

Using a graphical programming language to write CAMAC/GPIB instrument drivers

Science.gov (United States)

Zambrana, Horacio; Johanson, William

1991-01-01

To reduce the complexities of conventional programming, graphical software was used in the development of instrumentation drivers. The graphical software provides a standard set of tools (graphical subroutines) which are sufficient to program the most sophisticated CAMAC/GPIB drivers. These tools were used and instrumentation drivers were successfully developed for operating CAMAC/GPIB hardware from two different manufacturers: LeCroy and DSP. The use of these tools is presented for programming a LeCroy A/D Waveform Analyzer.

Two experimental tests of relational models of procedural justice: non-instrumental voice and authority group membership.

Science.gov (United States)

Platow, Michael J; Eggins, Rachael A; Chattopadhyay, Rachana; Brewer, Greg; Hardwick, Lisa; Milsom, Laurin; Brocklebank, Jacinta; Lalor, Thérèse; Martin, Rowena; Quee, Michelle; Vassallo, Sara; Welsh, Jenny

2013-06-01

In both a laboratory experiment (in Australia) using university as the basis of group membership, and a scenario experiment (in India) using religion as the basis of group membership, we observe more favourable respect and fairness ratings in response to an in-group authority than an out-group authority who administers non-instrumental voice. Moreover, we observe in our second experiment that reported likelihood of protest (herein called "social-change voice") was relatively high following non-instrumental voice from an out-group authority, but relatively low following non-instrumental voice from an in-group authority. Our findings are consistent with relational models of procedural justice, and extend the work by examining likely use of alternative forms of voice as well as highlighting the relative importance of instrumentality. ©2012 The British Psychological Society.

Avoidance-based human Pavlovian-to-instrumental transfer

Science.gov (United States)

Lewis, Andrea H.; Niznikiewicz, Michael A.; Delamater, Andrew R.; Delgado, Mauricio R.

2013-01-01

The Pavlovian-to-instrumental transfer (PIT) paradigm probes the influence of Pavlovian cues over instrumentally learned behavior. The paradigm has been used extensively to probe basic cognitive and motivational processes in studies of animal learning but, more recently, PIT and its underlying neural basis have been extended to investigations in humans. These initial neuroimaging studies of PIT have focused on the influence of appetitively conditioned stimuli on instrumental responses maintained by positive reinforcement, and highlight the involvement of the striatum. In the current study, we sought to understand the neural correlates of PIT in an aversive Pavlovian learning situation when instrumental responding was maintained through negative reinforcement. Participants exhibited specific PIT, wherein selective increases in instrumental responding to conditioned stimuli occurred when the stimulus signaled a specific aversive outcome whose omission negatively reinforced the instrumental response. Additionally, a general PIT effect was observed such that when a stimulus was associated with a different aversive outcome than was used to negatively reinforce instrumental behavior, the presence of that stimulus caused a non-selective increase in overall instrumental responding. Both specific and general PIT behavioral effects correlated with increased activation in corticostriatal circuitry, particularly in the striatum, a region involved in cognitive and motivational processes. These results suggest that avoidance-based PIT utilizes a similar neural mechanism to that seen with PIT in an appetitive context, which has implications for understanding mechanisms of drug-seeking behavior during addiction and relapse. PMID:24118624

Bill project authorizing the approval of the amendment to the convention on physical protection of nuclear material - Nr 11

International Nuclear Information System (INIS)

Ayrault, Jean-Marc; Fabius, Laurent

2012-01-01

This document contains the brief text of the bill project and the text of the amendment to the Convention on physical protection of nuclear material which has been adopted in Vienna in August 2005 to amend the Convention adopted in October 1979. This amendment introduces the following measures: extension of the scope of application of the Convention to nuclear materials used for peaceful purposes, definition of the objectives of the Convention, articulation of the Convention with other international instruments, definition of the main principles of physical protection, strengthened international cooperation, legal issues concerning extradition and legal cooperation

Thermal processes identification using virtual instrumentation

Directory of Open Access Journals (Sweden)

Iosif OLAH

2007-12-01

Full Text Available In this paper the experimental identification problem of thermal processes is presented, in order to establish their mathematical models which permit the adoption of the automation solutions, respectively the specification of a suitable control law. With this aim in view, the authors resorted to use Virtual Instrumentation with the aid of the LabVIEW development medium. In order to solve the problem of acquisition and processing data from physical real processes, Virtual Instruments which provide at the end a mathematical model which is basis of choosing the automation equipment of the aim followed was designed and achieved. The achieved Virtual Instruments get the opportunity to be used either in student instruction field with the virtual processes identification techniques or to put the identification of some real processes to good use of diverse beneficiaries. The results of some experimental attempts which were achieved during different thermal processes, illustrate the utility of the demarches performed in this paper.

Instrument intercomparison in the high-energy mixed field at the CERN-EU reference field (CERF) facility.

Science.gov (United States)

Caresana, Marco; Helmecke, Manuela; Kubancak, Jan; Manessi, Giacomo Paolo; Ott, Klaus; Scherpelz, Robert; Silari, Marco

2014-10-01

This paper discusses an intercomparison campaign performed in the mixed radiation field at the CERN-EU (CERF) reference field facility. Various instruments were employed: conventional and extended-range rem counters including a novel instrument called LUPIN, a bubble detector using an active counting system (ABC 1260) and two tissue-equivalent proportional counters (TEPCs). The results show that the extended range instruments agree well within their uncertainties and within 1σ with the H*(10) FLUKA value. The conventional rem counters are in good agreement within their uncertainties and underestimate H*(10) as measured by the extended range instruments and as predicted by FLUKA. The TEPCs slightly overestimate the FLUKA value but they are anyhow consistent with it when taking the comparatively large total uncertainties into account, and indicate that the non-neutron part of the stray field accounts for ∼30 % of the total H*(10). © The Author 2013. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Implementation of a communication and control network for the instruments of a nuclear analytical laboratory

International Nuclear Information System (INIS)

Cunya, Eduardo; Baltuano, Oscar; Bedregal, Patricia

2013-01-01

This paper describes the implementation of a communication network and control for a conventional laboratory instruments and nuclear analytical processes based on CAN open field bus to control devices and machines. Hardware components and software developed as well as installation and configuration tools for incorporating new instruments to the network re presented. (authors).

Construction of a Chemical Sensor/Instrumentation Package Using Fiber Optic and Miniaturization Technology

Science.gov (United States)

Newton, R. L.

1999-01-01

The objective of this research was to construct a chemical sensor/instrumentation package that was smaller in weight and volume than conventional instrumentation. This reduction in weight and volume is needed to assist in further reducing the cost of launching payloads into space. To accomplish this, fiber optic sensors, miniaturized spectrometers, and wireless modems were employed. The system was evaluated using iodine as a calibration analyte.

Neutron instrumentation system

International Nuclear Information System (INIS)

Akiyama, Takao; Arita, Setsuo; Yuchi, Hiroyuki

1989-01-01

The neutron instrumentation system of this invention can greatly reduce the possibility that the shutdown flux is increased greater than a predetermiend value to cause scram due to vibrations caused by earthquakes or shocks in the neutron instrumentation system without injuring the reactor safety. That is, a sensor having a zero sensitivity to a neutron flux which is an object to be detected by the sensor (dummy sensor) is used together with a conventional sensor (a sensor having predetermined sensitivity to a neutron flux as an object to be measured ----- true sensor). Further, identical signal transmission cables, connector and the signal processing circuits are used for both of true sensor and the dummy sensor. The signal from the dummy sensor is subtracted from the signal from the true sensor at the output of the signal processing circuit. Since the output of the dummy sensor is zero during normal operation, the subtracted value is the same as the value from the true sensor. If the true sensor causes an output with the reason other than the neutron flux, this is outputted also from the dummy sensor but does not appear in the subtracted value. (I.S.)

MANAGER PRINCIPLES AS BASIS OF MANAGEMENT STYLE TRANSFORMATION

OpenAIRE

R. A. Kopytov

2011-01-01

The paper considers an approach which is based on non-conventional mechanisms of management style formation. The preset level of sustainable management is maintained by self-organized environment created in the process of management style transformation in efficient management principles. Their efficiency is checked within an adaptive algorithm. The algorithm is developed on the basis of combination of evaluative tools  and base of operational  proves. The operating algorithm capability is te...

Digital imaging in conventional diagnostic radiology: status and trends

International Nuclear Information System (INIS)

Pfeiler, M.; Marhoff, P.; Schipper, P.

1984-01-01

Digital techniques, i.e. techniques using microcomputers of minicomputers, are getting increasingly common in so-called conventional radiography. These nonreconstructive techniques are referred to here as 'digital, direct-imaging radiography' in order to contrast them with the reconstructive techniques of computerized tomography. Digitalisation of imaging and image processing operation and control will change the jobs of the radiologist and radiological assistants in such manner that only X-ray units with film-foil systems or with X-ray image intensification should be classified as conventional systems. Digital and conventional systems differ in that digital techniques imply the possibility of establishing data pools which may eventually be developed into a digital image interconnection and archiving system. The authors first describe the general system in which the digital imaging systems must be integrated on a medium-term and long-term basis and then proceed to discuss digital imaging and image processing in some more detail. (orig./WU) [de

Beam diagnostic instruments of TARN

International Nuclear Information System (INIS)

Watanabe, Shin-ichi.

1987-09-01

The paper summarizes the beam diagnostic instruments of the low energy ion accumulation ring; TARN. With these monitors, position, profiles, bunch structure, intensity, emittance and momentum spread were measured to evaluate the injection and stacking experiments. The monitors provide the sensitivity of a few μA for the nondestructive and a few nA for the destructive monitors. Discussions on monitor probe and electronics are presented on the basis of an achievement of the beam stacking experiments. (author)

System 80+ instrumentation and controls - certification of a reliable design

International Nuclear Information System (INIS)

Matzie, R.A.; Scarola, K.; Turk, R.S.

1993-01-01

ABB Combustion Engineering's (ABB) System 80+ advanced light water plant design includes a modern, fully digitized instrumentation and controls complex, Nuplex 80+. This complex incorporates an evolutionary advanced control room, replacing conventional analog instruments with more capable computer driven components. As a result, Nuplex 80+ results in significant improvements in operator information handling and control to enhance plant safety and availability. The design implements features which the U.S. NRC has determined to be acceptable for addressing the potential for common mode failure in software implemented for protective functions. (author)

X-ray powder crystallography with vertex instrumentation

International Nuclear Information System (INIS)

Chatzisotiriou, V.; Christofis, I.; Dimitriou, N.; Karvelas, S.; Karydas, A.G.; Loukas, D.; Pavlidis, A.; Spirou, S.; Dre, C.; Haralabidis, N.; Misiakos, K.; Tsoi, E.; Perdikatsis, V.; Psycharis, V.; Terzis, A.; Turchetta, R.

1998-01-01

An X-ray Diffractometer for Powder Crystallography is described along with experimental results and future plans. This is an intermediate instrument toward a long linear array system. Three channels of a silicon microstrip detector, are the detecting elements in the present instrument. Each detector channel is followed by a VLSI readout chain, which consists of a charge preamplifier with pulse shaping circuitry, a discriminator, and a 16-bit counter. Control and data acquisition is performed with a custom made PC readout card. A motorized goniometer scans the angle range of interest. Calibration of the system is done with reference samples and data which are captured with a one-channel conventional NaI detector. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

Inquisitive learning as a basis for instrumental teaching: : an essay on four underpinning principles of the Prince Claus Conservatoire’s instrumental teacher education

NARCIS (Netherlands)

Stolte, Tine; Dons, Karolien

2016-01-01

Up until 2005 Peter Mak was involved as pedagogy teacher in the instrumental teacher education of the Bachelor of Music of the Prince Claus Conservatoire. The programme’s pedagogy section consisted of modules developed by Peter including ‘Didactics’, ‘Learning processes’, ‘Study skills’, and

Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter

International Nuclear Information System (INIS)

1974-01-01

The Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter was drawn up at the Inter-Governmental Conference on the Dumping of Wastes at Sea, held in London from 30 October to 10 November 1972. The Governments of Mexico, the Union of Soviet Socialist Republics, the United Kingdom of Great Britain and Northern Ireland and the United States of America are the Depository Governments for instruments of ratification of, and accession to, the Convention, pursuant to Articles XVII and XVIII respectively [es

Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter

International Nuclear Information System (INIS)

1974-01-01

The Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter was drawn up at the Inter-Governmental Conference on the Dumping of Wastes at Sea, held in London from 30 October to 10 November 1972. The Governments of Mexico, the Union of Soviet Socialist Republics, the United Kingdom of Great Britain and Northern Ireland and the United States of America are the Depository Governments for instruments of ratification of, and accession to, the Convention, pursuant to Articles XVII and XVIII respectively

The use of instruments of logistics and marketing in transport enterprises in lubuskie voivodeship

Directory of Open Access Journals (Sweden)

Agnieszka Perzyńska

2016-09-01

Full Text Available Background: The aim of the article is to verify the logistics and marketing instruments used in transport enterprises in Lubuskie voivodeship. The article presents the results of surveys of transport companies. Based on these studies in transport enterprises in Lubuskie, the current level of the use of logistics and marketing instruments was determined. Logistics and marketing instruments were separated to study the needs of transport companies in Lubuskie voivodeship. The choice of these instruments gave rise to a study f the possibility of using them in the implementation of business operations. From the findings it can be inferred that they are useful for the voivodeship, and that such a system can be implemented in the whole country. Methods: The study was conducted in the second half of 2014 and 140 transport enterprises in Lubuskie. Based on the research results, classifications of instruments were developed using logistics and marketing division at their levels. Results: On the basis of these findings and observations, the authors have analysed the levels of identification instruments, logistics and marketing. On this basis, it was possible to identify the instruments used by logistics and marketing in these companies. Conclusions: Based on the study of transport companies in Lubuskie voivodeship, a selection of logistics and marketing instruments were identified, along with a classification of the logistics and marketing instruments used. With the implementation of the above steps to classify the usage level of logistics and marketing instruments, the ability to match these levels to data transport companies was established.

Patient-Reported Outcome and Quality of Life Instruments Database (PROQOLID: Frequently asked questions

Directory of Open Access Journals (Sweden)

Perrier Laure-Lou

2005-03-01

Full Text Available Abstract The exponential development of Patient-Reported Outcomes (PRO measures in clinical research has led to the creation of the Patient-Reported Outcome and Quality of Life Instruments Database (PROQOLID to facilitate the selection process of PRO measures in clinical research. The project was initiated by Mapi Research Trust in Lyon, France. Initially called QOLID (Quality of Life Instruments Database, the project's purpose was to provide all those involved in health care evaluation with a comprehensive and unique source of information on PRO and HRQOL measures available through the Internet. PROQOLID currently describes more than 470 PRO instruments in a structured format. It is available in two levels, non-subscribers and subscribers, at http://www.proqolid.org. The first level is free of charge and contains 14 categories of basic useful information on the instruments (e.g. author, objective, original language, list of existing translations, etc.. The second level provides significantly more information about the instruments. It includes review copies of over 350 original instruments, 120 user manuals and 350 translations. Most are available in PDF format. This level is only accessible to annual subscribers. PROQOLID is updated in close collaboration with the instruments' authors on a regular basis. Fifty or more new instruments are added to the database annually. Today, all of the major pharmaceutical companies, prestigious institutions (such as the FDA, the NIH's National Cancer Institute, the U.S. Veterans Administration, dozens of universities, public institutions and researchers subscribe to PROQOLID on a yearly basis. More than 800 users per day routinely visit the database.

Provenance study of obsidian samples by using portable and conventional X ray fluorescence spectrometers. Performance comparison of both instrumentations

International Nuclear Information System (INIS)

Cristina Vazquez

2012-01-01

The potentiality of portable instrumentation lies on the possibility of the in situ determinations. Sampling, packaging and transport of samples from the site to the laboratory are avoided and the analysis becomes non destructive at all. However, detection limits for light elements are, in most cases, a limitation for quantification purposes. In this work a comparison between the results obtained with an X ray fluorescence spectrometer laboratory based and a portable instrument is performed. A set of 76 obsidian archaeological specimens from northwest Patagonia, Argentina was used to carry out the study. Samples were collected in the area of the middle and high basin of the Limay River. The analytical information obtained with both instrumentations was complemented with Principal Component Analysis in order to define groups and identify provenance sources. The information from both instruments allows arriving to the same conclusion about sample provenance and mobility of hunter-gatherer groups. Three groups of sources were identified in both cases matching with the geographical information. Also, same sets of outlier samples or not associated to these sources were found. Artifact samples were associated mainly to the closest sources, but some of them are related to sources located more than three hundred kilometers, evidencing the large mobility of the hunter-gatherers by the obsidian interchange. No significant differences between concentrations values obtained by laboratory based instrument and portable one were found. (author)

A philosophical and critical analysis of the European convention of bioethics.

Science.gov (United States)

Hottois, G

2000-04-01

The Convention for the Protection of Human Rights and Dignity of the Human Being with Regard to the Application of Biology and Medicine is now one of the most important bioethics texts from the point of view of international policy and law. It is the result of five years of discussions and negotiations between the different instances of the Council of Europe. In this article I analyze several problems. First, there are problems of articulation between the Convention and the joint Explanatory Report. The oriented exegesis of the Explanatory Report raises suspicion about the Convention, which appears as a smooth facade for an instrument actually serving ideological positions many people do not share. Second, there are problems of formulation within the Convention. These are mainly problems with articles that state prohibitions without any distinction, relativization, contextualization or sense of evolution. Finally, there are problems of substance, leading to the conclusion that the Convention is not a good illustration of the human rights philosophical tradition in the name of which it has been proclaimed. This tradition is the one of Enlightenment. And when Kant summarizes the motto of Enlightenment, the injunction is "Sapere Aude!": "Dare to know!" It is difficult to hear such a message through the Convention, and the Explanatory Report includes too many passages and sentences that mean the opposite.

Rules of Origin as Commercial Policy Instruments.

OpenAIRE

Falvey, Rod; Reed, Geoff

1997-01-01

This article examines the role of rules of origin as a commercial policy instrument that targets the input composition of imports. Using a three-country, partial equilibrium structure, we demonstrate conditions under which the imposition of a binding rule will be welfare improving for an importer facing competitive export suppliers. We further show that employing rules of origin in this way would be complementary to, rather than a substitute for, conventional optimal tariffs. Copyright Econom...

Experience with instrumentational monitoring of steam turbine foundations

International Nuclear Information System (INIS)

Linnemann, H.; Hagemann, M.

1989-01-01

Many factors can lead to the deformation of foundations and consequently to variations in the state of alignment of a turbine shaft line. Various measurement programmes, measurement procedures and instrumentation have been developed and proven in power plant practice. Experience accumulated hitherto with automatic measurement systems shows that these procedures are superior to conventional methods in respect of accuracy, availability and information content. (orig.) [de

The regulatory instruments for the correction of energy-related environmental externalities

International Nuclear Information System (INIS)

Labanderia Villot, X.; Lopez Otero, X.; Rodriguez Mendez, M.

2007-01-01

In this paper we deal with the different regulatory instruments for the correction of energy-related environmental externalities. This objective is justified by the size and general occurrence of this type of externalities in contemporary societies. In this sense, we distinguish between three main generations of instruments: conventional regulations, market mechanisms and voluntary approaches. In all cases, some practical examples of their application are presented, albeit emphasizing the experience with the so-called market instruments and the results of hypothetical simulations for the Spanish case. As a general conclusion we underline the role of economic analysis in the design, choice and evaluation of those mechanisms, which also explains the structure and contents of the article. (Author)

Requirements of the London Convention for dumping radioactive waste at sea

International Nuclear Information System (INIS)

Sutton, H.C.

1982-10-01

This report outlines the requirements of the London Convention for dumping radioactive waste at sea and considers their scientific basis more fully. It is intended primarily as an appraisal and aid to understanding of the two documents IAEA 210 and IAEA 211, published by the International Atomic Energy Agency, and relating to the oceanographic and radiobiological basis of their definitions of high level waste and recommendations relating to its dumping at sea, which were required for London Convention purposes. The adequacy and conservation in these recommendations are considered, and the report also compares the predictions of the model on which the recommendations are based with some limited but relevant observations on radiation doses resulting from natural causes (radium in the sea), and from fallout from nuclear bomb tests. It is concluded that if dumping is carried out within the limits and according to the recommendations required by the IAEA, then it is extremely unlikely that this could lead to significant human hazard, either now or in the future. Some of the reasons for this conclusion are summarised in the final chapter

Influence of cyclic torsional preloading on cyclic fatigue resistance of nickel - titanium instruments.

Science.gov (United States)

Pedullà, E; Lo Savio, F; Boninelli, S; Plotino, G; Grande, N M; Rapisarda, E; La Rosa, G

2015-11-01

To evaluate the effect of different torsional preloads on cyclic fatigue resistance of endodontic rotary instruments constructed from conventional nickel-titanium (NiTi), M-Wire or CM-Wire. Eighty new size 25, 0.06 taper Mtwo instruments (Sweden & Martina), size 25, 0.06 taper HyFlex CM (Coltene/Whaledent, Inc) and X2 ProTaper Next (Dentsply Maillefer) were used. The Torque and distortion angles at failure of new instruments (n = 10) were measured, and 0% (n = 10), 25%, 50% and 75% (n = 20) of the mean ultimate torsional strength as preloading condition were applied according to ISO 3630-1 for each brand. The twenty files tested for every extent of preload were subjected to 20 or 40 torsional cycles (n = 10). After torsional preloading, the number of cycles to failure was evaluated in a simulated canal with 60° angle of curvature and 5 mm of radius of curvature. Data were analysed using two-way analysis of variance. The fracture surface of each fragment was examined with a scanning electron microscope (SEM). Data were analysed by two-way analyses of variance. Preload repetitions did not influence the cyclic fatigue of the three brands; however, the 25%, 50% and 75% torsional preloading significantly reduced the fatigue resistance of all instruments tested (P 0.05). Torsional preloads reduced the cyclic fatigue resistance of conventional and treated (M-wire and CM-wire) NiTi rotary instruments except for size 25, 0.06 taper HyFlex CM instruments with a 25% of torsional preloading. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Convention on Nuclear Safety. Second National Report, October 2001

International Nuclear Information System (INIS)

2001-01-01

The present document is the second Spanish national report prepared in order to comply with the obligations deriving from the convention on Nuclear Safety, made in Vienna on 20th September 1994. This convention was signed by Spain on 15th October 1994 and ratified by way of an instrument issued by the Ministry of Foreign Affairs, signed by H. M. the King on 19th June 1995. The convention, which entered into force on 24th October 1996, following ratification by a minimum number of countries, as set out in articles 20, 21 and 22 includes 51 countries and Euratom, in addition to Spain. The first review meeting, organised in accordance with chapter 3 of the Convention, was held in vienna in April 1999. Spain was represented by the CSN, the State organisation solely responsible for nuclear safety, both for the drawing up of the national report and for participation in the meeting held between the parties. In accordance with article 21, the second review meeting has been scheduled for April 2002, also in Vienna. At the review meeting, the countries party to the Convention review the national reports required by article 5, Spain submitted its first national report in September 1998. The present document is an update of that first report, and is to be submitted by 15th October 2001, as agreed on during the first review meeting. This report will be reviewed by the interested countries, which will forward their comments and questions. In April 2002, the Spanish report and the questions received will be subjected to the review process contemplated by the convention, along with the reports submitted by the other countries

Influence of Loading Rate on the Calibration of Instrumented Charpy Strikers

Energy Technology Data Exchange (ETDEWEB)

Lucon, E.; Scibetta, M.; McColskey, D.; McCowan, C.

2009-01-15

One of the key factors for obtaining reliable instrumented Charpy results is the calibration of the instrumented striker. The conventional approach for establishing an analytical relationship between strain gage output and force applied to the transducer is the static calibration, which is preferably performed with the striker installed in the pendulum assembly. However, the response of an instrumented striker under static force application may sometimes differ significantly from its dynamic performance during an actual Charpy test. This is typically reflected in a large difference between absorbed energy returned by the pendulum encoder (KV) and calculated under the instrumented force/displacement test record (Wt). Such difference can be either minimized by optimizing the striker design or analytically removed by adjusting forces and displacements until KV = Wt (the so-called 'Dynamic Force Adjustment'). This study investigates the influence of increasing force application rates on the force/voltage characteristics of two instrumented strikers, one at NIST in Boulder, CO and one at SCK-CEN in Mol, Belgium.

Calibration through on-line monitoring of instruments channels

International Nuclear Information System (INIS)

James, R.W.

1996-01-01

Plant technical specifications require periodic calibration of instrument channels, and this has traditionally meant calibration at fixed time intervals for nearly all instruments. Experience has shown that unnecessarily frequent calibrations reduce channel availability and reliability, impact outage durations, and increase maintenance costs. An alternative approach to satisfying existing requirements for periodic calibration consists of on-line monitoring and quantitative comparison of instrument channels during operation to identify instrument degradation and failure. A Utility Working Group has been formed by EPRI to support the technical activities necessary to achieve generic NRC acceptance of on-line monitoring of redundant instrument channels as a basis for determining when to perform calibrations. A topical report proposing NRC acceptance of this approach was submitted in August 1995, and the Working Group is currently resolving NRC technical questions. This paper describes the proposed approach and the current status of the topical report with regard to NRC review. While these activities will not preclude utilities from continuing to use existing calibration approaches, successful acceptance of this performance-based approach will allow utilities to substantially reduce the number of calibrations which are performed. Concurrent benefits will include reduced I ampersand C impact on outage durations and improved sensitivity to instrument channel performance

Application of the Vienna Convention and the implementation at worldwide level of nuclear liability principles

International Nuclear Information System (INIS)

Martinez Favini, J.

1985-01-01

This paper analyses the distinction between the status of the Vienna Convention and the status of the incorporation of the Convention's principles in national laws. Ten countries are Parties to the Vienna Convention, three others have signed it (only one of which could become a Party in the short term) and only two have established legislation. In such circumstances, and for the future, any analysis should be expanded to encompass the present and potential difficulties of the nuclear industry which has been particularly affected by the world economic and financial crisis. Also, a better understanding of the basic differences between the majority of countries which are potential parties to the Vienna Convention and the countries parties to the Paris Convention should be attained by a study on a case-by-case basis. (NEA) [fr

Biomechanical investigation of an alternative concept to angular stable plating using conventional fixation hardware

Directory of Open Access Journals (Sweden)

Radtke Roman

2010-05-01

Full Text Available Abstract Background Angle-stable locking plates have improved the surgical management of fractures. However, locking implants are costly and removal can be difficult. The aim of this in vitro study was to evaluate the biomechanical performance of a newly proposed crossed-screw concept ("Fence" utilizing conventional (non-locked implants in comparison to conventional LC-DCP (limited contact dynamic compression plate and LCP (locking compression plate stabilization, in a human cadaveric diaphyseal gap model. Methods In eight pairs of human cadaveric femora, one femur per pair was randomly assigned to receive a Fence construct with either elevated or non-elevated plate, while the contralateral femur received either an LCP or LC-DCP instrumentation. Fracture gap motion and fatigue performance under cyclic loading was evaluated successively in axial compression and in torsion. Results were statistically compared in a pairwise setting. Results The elevated Fence constructs allowed significantly higher gap motion compared to the LCP instrumentations (axial compression: p ≤ 0.011, torsion p ≤ 0.015 but revealed similar performance under cyclic loading (p = 0.43. The Fence instrumentation with established bone-plate contact revealed larger fracture gap motion under axial compression compared to the conventional LC-DCP osteosynthesis (p ≤ 0.017. However, all contact Fence specimens survived the cyclic test, whereas all LC-DCP constructs failed early during torsion testing (p Conclusions Even though accentuated fracture gap motion became obvious, the "Fence" technique is considered an alternative to cost-intensive locking-head devices. The concept can be of interest in cases were angle-stable implants are unavailable and can lead to new strategies in implant design.

Bill project authorizing the approval of the amendment to the Convention on the physical protection of nuclear materials

International Nuclear Information System (INIS)

Juppe, Alain; Fillon, Francois

2011-01-01

This document deals with the amendment to the Convention on the Physical Protection of Nuclear Materials which has been adopted in July 2005. This amendment notably extended the Convention's scope, objectives, relation with other international instruments and content (regarding cooperation, sanctions, and so on). After the text of this amendment, this document contains the bill project which reports an impact study (estimated economic, financial, environmental, and legal consequences of the amendment implementation), comments the penal and criminal cooperation defined in the Convention. A table indicates the impact of the amendment's articles on the French law

A review on mathematical methods of conventional and Islamic derivatives

Science.gov (United States)

Hisham, Azie Farhani Badrol; Jaffar, Maheran Mohd

2014-12-01

Despite the impressive growth of risk management tools in financial institutions, Islamic finance remains miles away behind the conventional institutions. Islamic finance products need to comply with the syariah law and prohibitions, therefore they can use fewer of the available risk management tools compared to conventional. Derivatives have proven to be the effective hedging technique and instrument that broadly being used in the conventional institutions to manage their risks. However, derivatives are not generally accepted as the legitimate products in Islamic finance and they remain controversial issues among the Islamic scholars. This paper reviews the evolution of derivatives such as forwards, futures and options and then explores the mathematical models that being used to solve derivatives such as random walk model, asset pricing model that follows Brownian motion and Black-Scholes model. Other than that, this paper also critically discuss the perspective of derivatives from Islamic point of view. In conclusion, this paper delivers the traditional Islamic products such as salam, urbun and istijrar that can be used to create building blocks of Islamic derivatives.

Instrumentation to Enhance Advanced Test Reactor Irradiations

Energy Technology Data Exchange (ETDEWEB)

J. L. Rempe; D. L. Knudson; K. G. Condie; J. E. Daw; S. C. Taylor

2009-09-01

The Department of Energy (DOE) designated the Advanced Test Reactor (ATR) as a National Scientific User Facility (NSUF) in April 2007 to support U.S. leadership in nuclear science and technology. By attracting new research users - universities, laboratories, and industry - the ATR will support basic and applied nuclear research and development, further advancing the nation's energy security needs. A key component of the ATR NSUF effort is to prove new in-pile instrumentation techniques that are capable of providing real-time measurements of key parameters during irradiation. To address this need, an assessment of instrumentation available and under-development at other test reactors has been completed. Based on this review, recommendations are made with respect to what instrumentation is needed at the ATR and a strategy has been developed for obtaining these sensors. Progress toward implementing this strategy is reported in this document. It is anticipated that this report will be updated on an annual basis.

Instrumentation to Enhance Advanced Test Reactor Irradiations

International Nuclear Information System (INIS)

Rempe, J.L.; Knudson, D.L.; Condie, K.G.; Daw, J.E.; Taylor, S.C.

2009-01-01

The Department of Energy (DOE) designated the Advanced Test Reactor (ATR) as a National Scientific User Facility (NSUF) in April 2007 to support U.S. leadership in nuclear science and technology. By attracting new research users - universities, laboratories, and industry - the ATR will support basic and applied nuclear research and development, further advancing the nation's energy security needs. A key component of the ATR NSUF effort is to prove new in-pile instrumentation techniques that are capable of providing real-time measurements of key parameters during irradiation. To address this need, an assessment of instrumentation available and under-development at other test reactors has been completed. Based on this review, recommendations are made with respect to what instrumentation is needed at the ATR and a strategy has been developed for obtaining these sensors. Progress toward implementing this strategy is reported in this document. It is anticipated that this report will be updated on an annual basis.

Applicability of analytical instrument in trace evidence analysis

International Nuclear Information System (INIS)

Sharma, Mukesh; Jha, Shailendra

2014-01-01

In the present paper, we explain the importance of the analytical instrument used in the field of forensic science for the analysis of the trace evidences collected from the scene of occurrence. The forensic scientist has to rely upon these instrumental analyses of trace amounts of materials like drugs, toxicological specimens, GSR, fibres, glass, paints, soil etc. Through this paper, reviews on these techniques which are extensively used in forensic sciences are reported. Our report summaries on the basis of analytical problem facing for a forensic expert and techniques employed to tackle them like XRD/XRF, inductively coupled plasma (ICP) techniques, Raman spectroscopy and microscopy (optical, GRIM, electron microscopy, TEM). (author)

Use of fuel reprocessing plant instrumentation for international safeguards

International Nuclear Information System (INIS)

Ayers, A.L.

1977-01-01

The International Atomic Energy Agency has a program for developing instrumentation to be used by safeguards inspectors at reprocessing facilities. These instruments have generally been individual pieces of equipment for improving the accuracy of existing measurement instrumentation or equipment to perform nondestructive assay on a selected basis. It is proposed that greater use be made of redundant plant instrumentation and data recovery systems that could augment plant instrumentation to verify the validity of plant measurements. Use of these methods for verfication must be proven as part of an operating plant before they can be relied upon for safeguards surveillance. Inspectors must be qualified in plant operations, or have ready access to those so qualified, if the integrity of the operation is to be properly assessed. There is an immediate need for the development and in-plant proof testing of an integrated gamma, passive neutron, and active neutron measurement system for drum quantities of radioactive trash. The primary safeguards effort should be limited to plutonium and highly enriched uranium

Clinical Evaluation of Quality of Obturation and Instrumentation Time using Two Modified Rotary File Systems with Manual Instrumentation in Primary Teeth.

Science.gov (United States)

Govindaraju, Lavanya; Jeevanandan, Ganesh; Subramanian, Emg

2017-09-01

Pulp therapy in primary teeth has been performed using various instrumentation techniques. However, the conventional instrumentation technique used for root canal preparation in primary teeth is hand instrumentation. Various Nickel-Titanium (Ni-Ti) instruments are available to perform efficient root canal preparation in primary teeth. These Ni-Ti instruments has been designed to aid in better root canal preparation in permanent teeth but are rarely used in primary teeth. It is necessary to assess the feasibility of using these adult rotary files with a modified sequence in primary teeth. To compare the quality of obturation and instrumentation time during root canal preparation using hand files and modified rotary file systems in primary molars. Forty-five primary mandibular molars were randomly assigned to three experimental groups (n=15). Group I was instrumented using k-hand files, Group II with S2 ProTaper universal file and Group III with 0.25 tip 4% taper K3 rotary file. Standardized digital radiographs were taken before and after root canal instrumentation. Root canal preparation time was also recorded. Statistical analysis of the obtained data was done using SPSS Software version 17.0. An intergroup comparison of the instrumentation time and the quality of obturation was done using ANOVA and Chi-square test with the level of significance set at 0.05. No significant differences were noted with regard to the quality of obturation (p=0.791). However, a statistically significant difference was noted in the instrumentation time between the three groups (pProTaper rotary system had significantly lesser instrumentation time when compared to that of K3 rotary system and hand file system. The hand files, S2 ProTaper Universal and K3 0.25 tip 4% taper files systems performed similarly with respect to the quality of obturation. There was a significant difference in instrumentation time with manual instrumentation compared to the modified rotary file systems in primary

The inherited basis of human radiosensitivity

International Nuclear Information System (INIS)

Gatti, R.A.

2001-01-01

Certain individuals cannot tolerate 'conventional' doses of radiation therapy. This is known to be true of patients with ataxia-telangiectasia and ligase IV deficiency. Although in vitro testing may not correlate completely with clinical radiosensitivity, fibroblasts and lymphoblasts from patients with both of these disorders have been clearly shown to be radiosensitive. Using a colony survival assay (CSA) to test lymphoblastoid cells after irradiation with 1 Gy, a variety of other genetic disorders have been identified as strong candidates for clinical radiosensitivity, such as Nijmegen breakage syndrome, Mre11 deficiency, and Fanconi's anemia. These data are presented and considered as a starting-point for the inherited basis of human radiosensitivity

77 FR 5768 - Application(s) for Duty-Free Entry of Scientific Instruments

Science.gov (United States)

2012-02-06

... California, Davis, NEAT ORU, One Shields Ave. Davis, CA 95616. Instrument: Alexsys 1000 Calorimeter... where such solvents are molten. Conventional differential scanning calorimeters, made by other companies... sensitive detector that is essential for solution calorimetry. Justification for Duty-Free Entry: There are...

Ex vivo study on root canal instrumentation of two rotary nickel-titanium systems in comparison to stainless steel hand instruments.

Science.gov (United States)

Vaudt, J; Bitter, K; Neumann, K; Kielbassa, A M

2009-01-01

To investigate instrumentation time, working safety and the shaping ability of two rotary nickel-titanium (NiTi) systems (Alpha System and ProTaper Universal) in comparison to stainless steel hand instruments. A total of 45 mesial root canals of extracted human mandibular molars were selected. On the basis of the degree of curvature the matched teeth were allocated randomly into three groups of 15 teeth each. In group 1 root canals were prepared to size 30 using a standardized manual preparation technique; in group 2 and 3 rotary NiTi instruments were used following the manufacturers' instructions. Instrumentation time and procedural errors were recorded. With the aid of pre- and postoperative radiographs, apical straightening of the canal curvature was determined. Photographs of the coronal, middle and apical cross-sections of the pre- and postoperative canals were taken, and superimposed using a standard software. Based on these composite images the portion of uninstrumented canal walls was evaluated. Active instrumentation time of the Alpha System was significantly reduced compared with ProTaper Universal and hand instrumentation (P < 0.05; anova). No instrument fractures occurred in any of the groups. The Alpha System revealed significantly less apical straightening compared with the other instruments (P < 0.05; Mann-Whitney U test). In the apical cross-sections Alpha System resulted in significantly less uninstrumented canal walls compared with stainless steel files (P < 0.05; chi-squared test). Despite the demonstrated differences between the systems, an apical straightening effect could not be prevented; areas of uninstrumented root canal wall were left in all regions using the various systems.

Diverticular Disease: Reconsidering Conventional Wisdom

Science.gov (United States)

Peery, Anne F.; Sandler, Robert S.

2013-01-01

Colonic diverticula are common in developed countries and complications of colonic diverticulosis are responsible for a significant burden of disease. Several recent publications have called into question long held beliefs about diverticular disease. Contrary to conventional wisdom, studies have not shown that a high fiber diet protects against asymptomatic diverticulosis. The risk of developing diverticulitis among individuals with diverticulosis is lower than the 10–25% commonly quoted, and may be as low as 1% over 11 years. Nuts and seeds do not increase the risk of diverticulitis or diverticular bleeding. It is unclear whether diverticulosis, absent diverticulitis or overt colitis, is responsible for chronic gastrointestinal symptoms or worse quality of life. The role of antibiotics in acute diverticulitis has been challenged by a large randomized trial that showed no benefit in selected patients. The decision to perform elective surgery should be made on a case-by-case basis and not routinely after a second episode of diverticulitis, when there has been a complication, or in young people. A colonoscopy should be performed to exclude colon cancer after an attack of acute diverticulitis but may not alter outcomes among individuals who have had a colonoscopy prior to the attack. Given these surprising findings, it is time to reconsider conventional wisdom about diverticular disease. PMID:23669306

The Legal Strength of International Health Instruments - What It Brings to Global Health Governance?

Directory of Open Access Journals (Sweden)

Haik Nikogosian

2016-12-01

Full Text Available Public health instruments have been under constant development and renewal for decades. International legal instruments, with their binding character and strength, have a special place in this development. The start of the 21st century saw, in particular, the birth of the first World Health Organization (WHO-era health treaties – the WHO Framework Convention on Tobacco Control (WHO FCTC and its first Protocol. The authors analyze the potential impact of these instruments on global health governance and public health, beyond the traditional view of their impact on tobacco control. Overall, the very fact that globally binding treaties in modern-era health were feasible has accelerated the debate and expectations for an expanded role of international legal regimes in public health. The impact of treaties has also been notable in global health architecture as the novel instruments required novel institutions to govern their implementation. The legal power of the WHO FCTC has enabled rapid adoption of further instruments to promote its implementation, thus, enhancing the international instrumentarium for health, and it has also prompted stronger role for national legislation on health. Notably, the Convention has elevated several traditionally challenging public health features to the level of international legal obligations. It has also revealed how the legal power of the international health instrument can be utilized in safeguarding the interests of health in the face of competing agendas and legal disputes at both the domestic and international levels. Lastly, the legal power of health instruments is associated with their potential impact not only on health but also beyond; the recently adopted Protocol to Eliminate Illicit Trade in Tobacco Products may best exemplify this matter. The first treaty experiences of the 21st century may provide important lessons for the role of legal instruments in addressing the unfolding challenges in global

The 1980 United Nations Convention on Contracts for the International Sale of Goods

DEFF Research Database (Denmark)

Lookofsky, Joseph

2012-01-01

On the basis of the central commercial importance of contracts of sale and the impressive and steadily growing list of ratifications (more than 75 States), the CISG Convention must be regarded as the most significant piece of substantive contract legislation in effect at the international level....

The 1980 United Nations Convention on Contracts for the International Sale of Goods

DEFF Research Database (Denmark)

Lookofsky, Joseph

2016-01-01

On the basis of the central commercial importance of contracts of sale and the impressive and steadily growing list of ratifications (more than 80 States), the CISG Convention must be regarded as the most significant piece of substantive contract legislation in effect at the international level....

Differences between elemental composition of orange juices and leaves from organic and conventional production systems

International Nuclear Information System (INIS)

Turra, C.; Fernandes, E.A.N.; Bacchi, M.A.; Tagliaferro, F.S.; Franca, E.J.

2006-01-01

A comprehensive sampling of organic and conventional oranges was carried out in Bebedouro, an important citrus producing region of Brazil. The soils, leaves and fruits of the variety Valencia (Citrus sinensis [L.] Osbeck) budded on Rangpur lime (Citrus limonia Osbeck) were analyzed. The chemical characterization was accomplished by instrumental neutron activation analysis (INAA). Indications for a difference between organic and conventional orange juices and leaves were obtained by applying univariate and multivariate statistical analysis. There were differences between samples for Br, Co, Cs, La and Rb from both systems. (author)

Instrumentation renewal at the FIR 1 research reactor in Finland

International Nuclear Information System (INIS)

Bars, Bruno; Kall, Leif

1982-01-01

The Finnish TRIGA Mark II reactor (FIR 1 100 kW, later 250 kW steady state power and pulsing capability up to 250 MW) has been in operation for 20 years. The reactor is the only research reactor in Finland and is an important research training and service facility, which obviously will be operated for 10...20 years ahead. The mechanical parts of the reactor are in good shape. Some minor modifications have previously been made in the instrumentation. However, the original instrumentation could hardly have been used for 10...20 years ahead without extensive modifications and modernization. After a careful evaluation and planning process the whole reactor instrumentation was renewed in 1981 at a cost of about 400 000 dollar. The renewal was carried out in cooperation with the Central Research Institute for Physics (KFKI) at the Hungarian Academy of Sciences, which delivered the nuclear part of the instrumentation and with the Finnish company Valmet Oy Instrument Works, which delivered the conventional instrumentation, including the automatic power control system and the control console. The instrumentation, which is located in-a new isolated control room is based on modern industrial standard modular units with standardized signal ranges, electronic testing possibilities, galvanically isolated outputs etc. The instrument renewal project was brought successfully to completion in November 1981 after only about 10 working days of shut down time. The reactor is now in routine operation and the experiences gained from the new instrumentation are excellent. (author)

Developments in the use of economic instruments in OECD countries

International Nuclear Information System (INIS)

Opschoor, H.

1994-01-01

For the period 1987-1993, developments in the environmental policies of OECD countries with respect to the use of economic instruments are compared and the differences analyzed. The focus is on applications in the field of air pollution policies. The comparison is made on the basis of two surveys. To complete the descriptive part, a brief survey is also presented of currently discussed and recently introduced economic instruments. A description of economic instruments as such and a review of rationales for employing economic and financial incentives precede this analysis. The analysis shows that the use of economic instruments has indeed increased since 1987, but the development has not been spectacular. Possible explanations for this are presented. Also, some types of instrument have advanced more than others and the changes differ from one set of countries to another. Product charges (including air pollution-related ones) have become more widely used, especially in Scandinavian countries. Moreover, growing attention is being paid to the use of economic instruments at the international level. The incentive impacts of economic (and other) instruments appear to have received relatively little empirical attention, even though these are an important policy-relevant feature in instrument choice. 23 refs., 5 tabs

Practical Application of Art. 9 OECD Model Convention: the Czech Republic

Directory of Open Access Journals (Sweden)

Veronika Solilová

2014-01-01

Full Text Available All transfer prices determined between the associated enterprises must comply with the arm’s length principle. The arm’s length principle for associated enterprises is mentioned in Art. 9(1 of the OECD Model Convention, which was also adopted by the OECD Member states into their national law. However, not all OECD Member states adopted the next part of Art. 9, namely Art. 9(2, with the same way, some of them, like the Czech Republic, entered a reservation on Art. 9 (2 OECD Model Convention. In this paper the practical application of Art. 9 is analyzed from the point of view of the Czech Ministry of Finance, where the corresponding adjustment and time-limit issue are highlighted. On the basis of the results of analysis, where the history, context and purpose of Art. 9 OECD Model Convention have to be taken into account, are made some recommendations.

Instruments of Inquiry: Understanding the Nature and Role of Design Tools

DEFF Research Database (Denmark)

Dalsgaard, Peter

2017-01-01

Designers employ a range of tools in most design projects, yet there are few frameworks for understanding how and why they work. On the basis of a well-established school of thought, pragmatism, this paper contributes with a coherent conceptualisation of tools in design, which I label instruments...... of inquiry. This perspective underscores the crucial role that instruments play in design, and the ways in which they scaffold design creativity and exploration. In particular, it highlights that instruments not only augment our capabilities for carrying out intended actions, they also guide our perception...... and understanding of design problems and solutions. I present and discuss a framework consisting of five qualities of instruments of inquiry, which make them valuable in designerly inquiry: perception, conception, externalisation, knowing-through-action, and mediation....

Evaluation of construct and criterion validity for the 'Liverpool Osteoarthritis in Dogs' (LOAD clinical metrology instrument and comparison to two other instruments.

Directory of Open Access Journals (Sweden)

Myles Benjamin Walton

Full Text Available To test the 'Liverpool Osteoarthritis in Dogs' (LOAD questionnaire for construct and criterion validity, and to similarly test the Helsinki Chronic Pain Index (HCPI and the Canine Brief Pain Inventory (CBPI.Prospective Study.222 dogs with osteoarthritis.Osteoarthritis was diagnosed in a cohort of dogs on the basis of clinical history and orthopedic examination. Force-platform analysis was performed and a "symmetry index" for peak vertical force (PVF was calculated. Owners completed LOAD, CBPI and HCPI instruments. As a test of construct validity, inter-instrument correlations were calculated. As a test of criterion validity, the correlations between instrument scores and PVF symmetry scores were calculated. Additionally, internal consistency of all instruments was calculated and compared to those previously reported. Factor analysis is reported for the first time for LOAD, and is compared to that previously reported for CBPI and HCPI.Significant moderate correlations were found between all instruments, implying construct validity for all instruments. Significant weak correlations were found between LOAD scores and PVF symmetry index, and between CBPI scores and PVF symmetry index.LOAD is an owner-completed clinical metrology instrument that can be recommended for the measurement of canine osteoarthritis. It is convenient to use, validated and, as demonstrated here for the first time, has a correlation with force-platform data.

INSTRUMENTAL PROVISION OF INDICATIVE MANAGEMENT FOOD INDUSTRY AND ITS IMPROVEMENT

Directory of Open Access Journals (Sweden)

N. V. Sirotkina

2013-01-01

Full Text Available The article is devoted to instruments of indicative management of industrial enterprises, which represent a means of making objective and operational administration solutions, theoretical research, as well as the implementation of management actions on the basis of the analytical and forecasting estimates management indicator.

Application of natural basis functions to soft x-ray tomography

International Nuclear Information System (INIS)

Ingesson, L.

2000-03-01

Natural basis functions (NBFs), also known as natural pixels in the literature, have been applied in tomographic reconstructions of simulated measurements for the JET soft x-ray system, which has a total of about 200 detectors spread over 6 directions. Various types of NBFs, i.e. normal, generalized and orthonormal NBFs, are reviewed. The number of basis functions is roughly equal to the number of measurements. Therefore, little a priori information is required as regularization and truncated singular-value decomposition can be used for the tomographic inversion. The results of NBFs are compared with reconstructions by the same solution technique using local basis functions (LBFs), and with the reconstructions of a conventional constrained-optimization tomography method with many more LBFs that requires more a priori information. Although the results of the conventional method are superior due to the a priori information, the results of the NBF and other LBF methods are reasonable and show the main features. Therefore, NBFs are a promising way to assess whether features in reconstructions are real or artefacts resulting from the a priori information. Of the NBFs, regular triangular (generalized) NBFs give the most acceptable reconstructions, much better than traditional square pixels, although the reconstructions with pyramid-shaped LBFs are also reasonable and have slightly smaller reconstruction errors. A more-regular (virtual) viewing geometry improves the reconstructions. However, simulations with a viewing geometry with a total of 480 channels spread over 12 directions clearly show that a priori information still improves the reconstructions considerably. (author)

The Convention on the Rights of Persons with Disabilities: Notes on Genealogy and Prospects

Science.gov (United States)

Winzer, Margret; Mazurek, Kas

2014-01-01

The dense and complex "Convention on the Rights of Persons with Disabilities" (CRPD) is both a human rights treaty and a development tool. It supplements the web of existing human rights instruments insofar as they relate to disability. Schooling is enshrouded as a rights-based case; inclusive education as a development tool for all…

Collaborative Learning in Architectural Education: Benefits of Combining Conventional Studio, Virtual Design Studio and Live Projects

Science.gov (United States)

Rodriguez, Carolina; Hudson, Roland; Niblock, Chantelle

2018-01-01

Combinations of Conventional Studio and Virtual Design Studio (VDS) have created valuable learning environments that take advantage of different instruments of communication and interaction. However, past experiences have reported limitations in regards to student engagement and motivation, especially when the studio projects encourage abstraction…

Biomechanical investigation of an alternative concept to angular stable plating using conventional fixation hardware.

Science.gov (United States)

Windolf, Markus; Klos, Kajetan; Wähnert, Dirk; van der Pol, Bas; Radtke, Roman; Schwieger, Karsten; Jakob, Roland P

2010-05-21

Angle-stable locking plates have improved the surgical management of fractures. However, locking implants are costly and removal can be difficult. The aim of this in vitro study was to evaluate the biomechanical performance of a newly proposed crossed-screw concept ("Fence") utilizing conventional (non-locked) implants in comparison to conventional LC-DCP (limited contact dynamic compression plate) and LCP (locking compression plate) stabilization, in a human cadaveric diaphyseal gap model. In eight pairs of human cadaveric femora, one femur per pair was randomly assigned to receive a Fence construct with either elevated or non-elevated plate, while the contralateral femur received either an LCP or LC-DCP instrumentation. Fracture gap motion and fatigue performance under cyclic loading was evaluated successively in axial compression and in torsion. Results were statistically compared in a pairwise setting. The elevated Fence constructs allowed significantly higher gap motion compared to the LCP instrumentations (axial compression: p concept can be of interest in cases were angle-stable implants are unavailable and can lead to new strategies in implant design.

From BASIS to MIRACLES: Benchmarking and perspectives for high-resolution neutron spectroscopy at the ESS

International Nuclear Information System (INIS)

Tsapatsaris, N.; Bordallo, H.N.; Willendrup, P.K.

2015-01-01

Results based on virtual instrument models for the first high-flux, high-resolution, spallation based, backscattering spectrometer, BASIS are presented in this paper. These were verified using the Monte Carlo instrument simulation packages McStas and VITESS. Excellent agreement of the neutron count rate at the sample position between the virtual instrument simulation and experiments was found, in both time and energy distributions. This achievement was only possible after a new component for a bent single crystal analyser in McStas, using a Gaussian approximation, was developed. These findings are pivotal to the conceptual design of the next generation backscattering spectrometer, MIRACLES at the European Spallation Source. (authors)

A Virtual Instrument System for Determining Sugar Degree of Honey

Directory of Open Access Journals (Sweden)

Qijun Wu

2015-01-01

Full Text Available This study established a LabVIEW-based virtual instrument system to measure optical activity through the communication of conventional optical instrument with computer via RS232 port. This system realized the functions for automatic acquisition, real-time display, data processing, results playback, and so forth. Therefore, it improved accuracy of the measurement results by avoiding the artificial operation, cumbersome data processing, and the artificial error in optical activity measurement. The system was applied to the analysis of the batch inspection on the sugar degree of honey. The results obtained were satisfying. Moreover, it showed advantages such as friendly man-machine dialogue, simple operation, and easily expanded functions.

A Virtual Instrument System for Determining Sugar Degree of Honey.

Science.gov (United States)

Wu, Qijun; Gong, Xun

2015-01-01

This study established a LabVIEW-based virtual instrument system to measure optical activity through the communication of conventional optical instrument with computer via RS232 port. This system realized the functions for automatic acquisition, real-time display, data processing, results playback, and so forth. Therefore, it improved accuracy of the measurement results by avoiding the artificial operation, cumbersome data processing, and the artificial error in optical activity measurement. The system was applied to the analysis of the batch inspection on the sugar degree of honey. The results obtained were satisfying. Moreover, it showed advantages such as friendly man-machine dialogue, simple operation, and easily expanded functions.

Evaluation of advanced two-phase flow instrumentation in SCTF Core-1

International Nuclear Information System (INIS)

Iwamura, Takamichi; Sobajima, Makoto; Osakabe, Masahiro; Ohnuki, Akira; Abe, Yutaka; Sudo, Yukio; Adachi, Hiromichi

1984-03-01

In the Slab Core Test Facility (SCTF) Core-I, advanced two-phase flow instruments have been provided by the USNRC to measure the thermohydraulic behavior in the primary system including pressure vessel during the end of blowdown, refill and reflood phases of a postulated loss-of-coolant accident in a pressurized water reactor. The advanced instruments are turbine meters, drag disks, γ-densitometers, spool pieces, liquid level detectors (LLD), fluid distribution grids (FDG), impedance probes (flag, prong and string probes), film probes, and video optical probes. This report presents evaluated results of the data from these instruments. Some instruments are quantitatively evaluated by comparing with the data from the conventional instruments or the other advanced instruments. Main conclusions are as follows: (1) The spool pieces and the γ-densitometers work well and provide satisfactory results; (2) Some of the turbine meters, the impedance probes and the film probes give partially reasonable results, but still more improvements are required; (3) Most of the LLDs, the FDGs, the impedance probes, and the film probes do not work well due to a hard cable corrosion, and (4) The video optical probes give clear image of the flow pattern. (author)

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''P''

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Test Plan provides a test method to dedicate the leak detection relays used on the new Pumping Instrumentation and Control (PIC) skids. The new skids are fabricated on-site. The leak detection system is a safety class system per the Authorization Basis

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid Q

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Test Plan provides a test method to dedicate the leak detection relays used on the new Pumping Instrumentation and Control (PIC) skids. The new skids are fabricated on-site. The leak detection system is a safety class system per the Authorization Basis

Basis of Estimate Software Tool (BEST) - a practical solution to part of the cost and schedule integration puzzle

International Nuclear Information System (INIS)

Murphy, L.; Bain, P.

1997-01-01

The Basis of Estimate Software Tool (BEST) was developed at the Rocky Flats Environmental Technology Site (Rocky Flats) to bridge the gap that exists in conventional project control systems between scheduled activities, their allocated or assigned resources, and the set of assumptions (basis of estimate) that correlate resources and activities. Having a documented and auditable basis of estimate (BOE) is necessary for budget validation, work scope analysis, change control, and a number of related management control functions. The uniqueness of BEST is demonstrated by the manner in which it responds to the diverse needs of the heavily regulated environmental workplace - containing many features not found in conventional off-the-shelf software products. However, even companies dealing in relatively unregulated work places will find many attractive features in BEST. This product will be of particular interest to current Government contractors and contractors preparing proposals that may require subsequent validation. 2 figs

The inherited basis of human radiosensitivity

Energy Technology Data Exchange (ETDEWEB)

Gatti, R.A. [Univ. of California, School of Medicine, Los Angeles, CA (United States). Experimental Pathology

2001-11-01

Certain individuals cannot tolerate 'conventional' doses of radiation therapy. This is known to be true of patients with ataxia-telangiectasia and ligase IV deficiency. Although in vitro testing may not correlate completely with clinical radiosensitivity, fibroblasts and lymphoblasts from patients with both of these disorders have been clearly shown to be radiosensitive. Using a colony survival assay (CSA) to test lymphoblastoid cells after irradiation with 1 Gy, a variety of other genetic disorders have been identified as strong candidates for clinical radiosensitivity, such as Nijmegen breakage syndrome, Mre11 deficiency, and Fanconi's anemia. These data are presented and considered as a starting-point for the inherited basis of human radiosensitivity.

15 CFR 742.18 - Chemical Weapons Convention (CWC or Convention).

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Chemical Weapons Convention (CWC or... REGULATIONS CONTROL POLICY-CCL BASED CONTROLS § 742.18 Chemical Weapons Convention (CWC or Convention). States... Use of Chemical Weapons and on Their Destruction, also known as the Chemical Weapons Convention (CWC...

Economics of wind power and comparisons with conventional thermal plant

International Nuclear Information System (INIS)

Milborrow, D.

1994-01-01

Commercial deployment of renewables in the UK depends on their prices converging with those of the conventional sources of generation. Price comparisons, however, are distorted by institutional factors such as the very short contract periods for premium prices under the first two rounds of the Non-Fossil Fuel Obligation (NFFO). Prices are therefore put on a common basis and the prospects for wind energy up to the year 2000 are examined. (author)

Strategy for improving instrumentation and control in operating nuclear power plants

International Nuclear Information System (INIS)

Abad Bassols, L.; Nino Perote, R.

1996-01-01

There are three basic reasons why nuclear power plants need to systematically upgrade their instrumentation and control equipment: Obsolete instrumentation and lack spares Little capacity of flexibility for extension Possibility of attaining better systems integration and improving systems-operations interface This article shows how to approach these issues using the following strategies: Use of distributed control systems and PLCs for control, signalling, command, communications, etc, in both nuclear and conventional applications Upgrading of process instrumentation equipment, sensors, transmitters, etc Upgrading of alarm-signalling systems In each group of equipment items consideration should be given to: Aspects regarding manufacturers-suppliers Effects on design, adaptation and documentation of operating plants Effects on the training and handling skills of operation and maintenance staff Strategy for incorporating the new system into the Plant with minimum impact on operation (Author)

New technology for BWR power plant control and instrumentation

International Nuclear Information System (INIS)

Takano, Yoshiyuki; Nakamura, Makoto; Murata, Fumio.

1992-01-01

Nuclear power plants are facing strong demands for higher reliability and cost-performance in their control and instrumentation systems. To meet these needs, Hitachi is developing advanced control and instrumentation technology by rationalizing the conventional technology in that field. The rationalization is done through the utilization of reliable digital technology and optical transmission technology, and others, which are now commonly used in computer applications. The goal of the development work is to ensure safe, stable operation of the plant facilities and to secure harmony between man and machine. To alleviate the burdens of the operators, the latest electronic devices are being employed to create an advanced man-machine interface, and to promote automatic operation of the plant based upon the automatic operation of individual systems. In addition, the control and instrumentation system, including the safety system, incorporates more and more digital components in order to further enhance the reliability and maintainability of the plant. (author)

Image quality in conventional chest radiography. Evaluation using the postprocessing tool Diamond View

International Nuclear Information System (INIS)

Niemann, Tilo; Reisinger, Clemens; Rau, Philipp; Schwarz, Jochen; Ruis-Lopez, Laura; Bongartz, Georg

2010-01-01

The objective of this work was to evaluate the influence of the postprocessing tool Diamond View (Siemens AG Medical Solutions, Germany) on image quality in conventional chest radiography. Evaluation of image quality remains a challenge in conventional radiography. Based on the European Commission quality criteria we evaluated the improvement of image quality when applying the new postprocessing tool Diamond View (Siemens AG Medical solutions, Germany) to conventional chest radiographs. Three different readers prospectively evaluated 102 digital image pairs of chest radiographs. Statistical analysis was performed with a p value <0.05 considered as significant. Images were evaluated on basis of the modified imaging Quality Criteria by the Commission of the European Communities. Each of the 11 image quality criteria was evaluated separately using a five point classification. Statistical analysis showed an overall tendency for improved image quality for Diamond View (DV) for all criteria. Significant differences could be found in most of the criteria. In conclusion DV improves image quality in conventional chest radiographs.

Combining policy instruments to curb greenhouse gas emissions

International Nuclear Information System (INIS)

Bahn, O.

2001-01-01

The Kyoto Protocol has set greenhouse gas emission reduction targets for selected countries. To comply with these reduction requirements, decision-makers may use market-based instruments on a national or international basis. This paper advocates the combining of national emission taxes with international trade of emission permits. As a numerical application, this paper analyses macro-economic impacts of such a strategy for Switzerland. (Author)

Food-related life styles in Singapore: Testing a Western European research instrument in Southeast Asia

DEFF Research Database (Denmark)

Askegaard, Søren; Brunsø, Karen; Crippen, Kaye

The food-related life style instrument developed by the MAPP research group has, up til now, been applied mainly in the context of European cultures. The purpose of the present study is to apply the food-related life style instrument in a new and very different cultural setting, to compare results......, and to interpret similarities and differences found. For this purpose, data have been collected in Singaporean families using the food-related life style instrument. A total of 89 questionnaires form the basis of the analysis. First, the cross-cultural validity of the instrument is tested, and secondly...

Overview and status of beam instrumentation at the SSC

International Nuclear Information System (INIS)

Webber, R.C.

1993-05-01

An overview of beam instrumentation requirements at the SSC and a status report on work progress is given. Small transverse emittance beams, ranging in energy from 30 KeV to 20 TeV, must be commissioned, measured, and diagnosed. Instrumentation plans and current design and development efforts for BPMs and other systems are presented. Monitors and electronics soon to be delivered for use in the Linac are described. Design of the Linac systems has been done with requirements and applications in the synchrotron in mind and thus should provide a basis for design of much of that hardware. The useful commonality of design across the machines is discussed

Comparison of Conventional and Semi-Conventional Management ...

African Journals Online (AJOL)

Comparison of Conventional and Semi-Conventional Management Systems on the Performance and Carcass Yield of Broiler Chickens. ... TO AFRICAN RESEARCH. AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search · USING AJOL · RESOURCES ... Journal Home > Vol 20, No 1 (2018) >. Log in or ...

Achievements and Perspectives of the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management

International Nuclear Information System (INIS)

Louvat, D.; Lacoste, A.C.

2006-01-01

The Joint Convention on the Safety of Spent Fuel management and on the Safety of Radioactive Waste Management is the first legal instrument to directly address the safety of spent fuel and radioactive waste management on a global scale. The Joint Convention entered into force in 2001. This paper describes its process and its main achievements to date. The perspectives to establish of a Global Waste Safety Regime based on the Joint Convention are also discussed. (authors)

Modeling and analysis of conventional and heat-integrated distillation columns

DEFF Research Database (Denmark)

Bisgaard, Thomas; Huusom, Jakob Kjøbsted; Abildskov, Jens

2015-01-01

A generic model that can cover diabatic and adiabatic distillation column configurations is presented, with the aim ofproviding a consistent basis for comparison of alternative distillation column technologies. Both a static and a dynamic formulation of the model, together with a model catalogue...... consisting of the conventional, the heat-integrated and the mechanical vapor recompression distillation columns are presented. The solution procedure of the model is outlined and illustrated in three case studies. One case study being a benchmark study demonstrating the size of the model and the static...... properties of two different heat-integrated distillation column (HIDiC) schemes and the mechanical vapor recompression column. The second case study exemplifies the difference between a HIDiC and a conventional distillation column in the composition profiles within a multicomponent separation, whereas...

A multipurpose hybrid conventional/scanning near-field optical microscope for applications in materials science and biology

International Nuclear Information System (INIS)

Longo, G; Girasole, M; Pompeo, G; Generosi, R; Luce, M; Cricenti, A

2010-01-01

A hybrid conventional/scanning near-field optical microscope is presented. The instrument is obtained coupling an Olympus IX-70 inverted optical microscope with a SNOM head, to combine the versatility and ease of use of the conventional microscope with the high-resolution and three-dimensional reconstruction achieved by the SNOM. The head can be run in shear or tapping mode and is optimized to characterize soft, biological samples including living cells in physiological environment by including the SNOM in a cylindrical chamber that insulates it from external noise, while maintaining a controlled temperature and atmosphere

Active instrumental guidance in interventional magnetic resonance imaging

International Nuclear Information System (INIS)

Wildermuth, S.; Erhart, P.; Leung, D.A.; Goehde, S.; Schoenenberger, A.; Debatin, J.F.

1998-01-01

Purpose: An active MR-based guidance system for visualisation of invasive instruments is described. Methods: The principle of MR tracking is based on the integration of a miniaturised coil into the tip of the instrument itself. A phantom experiment was designed to demonstrate the localising accuracy of this technique. In [dition, bicompatibility and warming effects were evaluated. Preliminary intravascular applications that were performed in animal experiments under MR guidance included embolisation, vascular occlusion as well as transjugular intrahepatic punctures. Percutaneous biopsies, cholecystostomies and laparoscopic applications were also evaluated with MR tracking. Results: Phantom experiments confirmed an excellent localisation accuracy of MR tracking compared to conventional r[iography. At a field strength of 0.5 T, the temperature increase remained below 2 C. Results of phantom experiments revealed a potential of significant heating dependent on the sequence parameters employed. MR tracking allowed a robust, simultaneously biplanar visualisation of the instrument tips in real time. Based on MR 'ro[ map' images, various intravascular and percutaneous interventions were successfully performed in vivo under MR guidance. Conclusions: MR tracking is a flexible concept permitting monitoring in the guidance of instruments in an MR environment. Various preliminary in vitro and in vivo experiments demonstrate safety, localisation accuracy and feasibility of this biplanar localisation technique in real time. (orig.) [de

The Brussels Nuclear Ship Convention and its impact on the German Atomic Energy Act

International Nuclear Information System (INIS)

Bernaerts, A.

1976-01-01

Although the Brussels Nuclear Ship Liability Convention of 1962, whose incorporation into German law was agreed upon by the German Federal Parliament (the Bundestag) in 1975, will have only minor international significance once it has entered into force, it will yet provide a new legal basis for the nuclear liability of the German vessel N.S. 'Otto Hahn' for the periods of her stay within the Federal Republic of Germany. However, there is no smooth concurrence of the Brussels Convention and the German Atomic Energy Act adapted to the Paris Liability Convention in 1975. This means that a number of questions still need to be resolved with respect to the protection of victims and the liability of shipowners. (orig.) [de

Development of instrumentation in the transport phenomena research in thermal equipment

International Nuclear Information System (INIS)

Carvalho Tofani, P. de; Ladeira, L.C.D.

1983-11-01

The results obtained from the effort on the acquisition of know-how in experimental reactor thermal during the last years, through the approach of relevant aspects of basic research on transport phenomena applicable to nuclear reactor analysis and conventional thermal equipment based in the simultaneous development of instrumentation and experimental methods are presented. (E.G.) [pt

Adopting New International Health Instruments - What Can We Learn From the FCTC? Comment on "The Legal Strength of International Health Instruments - What It Brings to Global Health Governance?"

Science.gov (United States)

Hesselman, Marlies; Toebes, Brigit

2017-07-15

This Commentary forms a response to Nikogosian's and Kickbusch's forward-looking perspective about the legal strength of international health instruments. Building on their arguments, in this commentary we consider what we can learn from the Framework Convention on Tobacco Control (FCTC) for the adoption of new legal international health instruments. © 2018 The Author(s); Published by Kerman University of Medical Sciences. This is an open-access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Comparison between conventional and piezoelectric surgical tools for maxillary sinus floor elevation : a randomized controlled clinical trial

NARCIS (Netherlands)

Rickert, Daniela; Vissink, Arjan; Huddleston Slater, James; Meijer, Henny J. A.; Raghoebar, Gerry M.

Aim: The aim of this study was to assess the performance of conventional rotative instruments and a piezoelectric device for maxillary sinus floor elevation surgery, and to assess whether application of a resorbable membrane reduces resorption of an augmented site in a randomized clinical trial.

The efficacy of selective calculus ablation at 400 nm: comparison to conventional calculus removal methods

Science.gov (United States)

Schoenly, Joshua E.; Seka, Wolf; Romanos, Georgios; Rechmann, Peter

A desired outcome of scaling and root planing is the complete removal of calculus and infected root tissue and preservation of healthy cementum for rapid healing of periodontal tissues. Conventional periodontal treatments for calculus removal, such as hand instrument scaling and ultrasonic scaling, often deeply scrape the surface of the underlying hard tissue and may leave behind a smear layer. Pulsed lasers emitting at violet wavelengths (specifically, 380 to 400 nm) are a potential alternative treatment since they can selectively ablate dental calculus without ablating pristine hard tissue (i.e., enamel, cementum, and dentin). In this study, light and scanning electron microscopy are used to compare and contrast the efficacy of in vitro calculus removal for several conventional periodontal treatments (hand instruments, ultrasonic scaler, and Er:YAG laser) to calculus removal with a frequency-doubled Ti:sapphire (λ = 400 nm). After calculus removal, enamel and cementum surfaces are investigated for calculus debris and damage to the underlying hard tissue surface. Compared to the smear layer, grooves, and unintentional hard tissue removal typically found using these conventional treatments, calculus removal using the 400-nm laser is complete and selective without any removal of pristine dental hard tissue. Based on these results, selective ablation from the 400-nm laser appears to produce a root surface that would be more suitable for successful healing of periodontal tissues.

MANU. Instrumentation of Buffer Demo. Preliminary Study

International Nuclear Information System (INIS)

Laaksonen, R.

2010-01-01

The purpose of this work is to describe feasible measuring and monitoring alternatives which can be used, if needed, in medium to full scale nuclear waste repository deposition hole mock-up tests. The focus of the work was to determine what variables can actually be measured, how to achieve the measurements and what kind of demands comes from the modelling, scientific, and technical points of view. This project includes a review of the previous waste repository mock-up tests carried out in several European countries such as Belgium, Czech Republic, Spain and Sweden. Also information was gathered by interviewing domestic and foreign scientists specialized in the fields of measurement instrumentation and related in-situ and laboratory work. On the basis of this review, recommendations were developed for the necessary actions needed to be done from the instrumentation point of view for future tests. It is possible to measure and monitor the processes going on in a deposition hole in-situ conditions. The data received during a test in real repository conditions enables to follow the processes and to verify the hypothesis made on the behaviour of various components of the repository: buffer, canister, rock and backfill. Because full scale testing is expensive, the objectives and hypothesis must be carefully set and the test itself with its instrumentation must serve very specific objectives. The main purpose of mock-up tests is to verify that the conditions surrounding the canister are according to the design requirements. A whole mock-up test and demonstration process requires a lot of time and effort. The instrumentation part of the work must also start at early stages to ensure that the instrumentation itself will not become bottlenecked nor suffer from low quality solutions. The planning of the instrumentation work could be done in collaboration with foreign scientists which have participated to previous instrumentation projects. (orig.)

Surgical Instrument Sets for Special Operations Expeditionary Surgical Teams.

Science.gov (United States)

Hale, Diane F; Sexton, Justin C; Benavides, Linda C; Benavides, Jerry M; Lundy, Jonathan B

The deployment of surgical assets has been driven by mission demands throughout years of military operations in Iraq and Afghanistan. The transition to the highly expeditious Golden Hour Offset Surgical Transport Team (GHOST- T) now offers highly mobile surgical assets in nontraditional operating rooms; the content of the surgical instrument sets has also transformed to accommodate this change. The 102nd Forward Surgical Team (FST) was attached to Special Operations assigned to southern Afghanistan from June 2015 to March 2016. The focus was to decrease overall size and weight of FST instrument sets without decreasing surgical capability of the GHOST-T. Each instrument set was evaluated and modified to include essential instruments to perform damage control surgery. The overall number of main instrument sets was decreased from eight to four; simplified augmentation sets have been added, which expand the capabilities of any main set. The overall size was decreased by 40% and overall weight decreased by 58%. The cardiothoracic, thoracotomy, and emergency thoracotomy trays were condensed to thoracic set. The orthopedic and amputation sets were replaced with an augmentation set of a prepackaged orthopedic external fixator set). An augmentation set to the major or minor basic sets, specifically for vascular injuries, was created. Through the reorganization of conventional FST surgical instrument sets to maintain damage control capabilities and mobility, the 102nd GHOST-T reduced surgical equipment volume and weight, providing a lesson learned for future surgical teams operating in austere environments. 2017.

A review of genome-wide approaches to study the genetic basis for spermatogenic defects.

Science.gov (United States)

Aston, Kenneth I; Conrad, Donald F

2013-01-01

Rapidly advancing tools for genetic analysis on a genome-wide scale have been instrumental in identifying the genetic bases for many complex diseases. About half of male infertility cases are of unknown etiology in spite of tremendous efforts to characterize the genetic basis for the disorder. Advancing our understanding of the genetic basis for male infertility will require the application of established and emerging genomic tools. This chapter introduces many of the tools available for genetic studies on a genome-wide scale along with principles of study design and data analysis.

High lane density slab-gel electrophoresis using micromachined instrumentation.

Science.gov (United States)

Papautsky, I; Mohanty, S; Weiss, R; Frazier, A B

2001-10-01

In this paper, micromachined pipette arrays (MPAs) and microcombs were studied as a means of enabling high lane density gel electrophoresis. The MPA provide a miniaturized format to interface sub-microliter volumes of samples between macroscale sample preparation formats and microscale biochemical analysis systems. The microcombs provide a means of creating sample loading wells in the gel material on the same center-to-center spacing as the MPAs. Together, the two micromachined instruments provide an alternative to current combs and pipetting technologies used for creating sample loading wells and sample delivery in gel electrophoresis systems. Using three designs for the microcomb-MPA pair, center-to-center spacings of 1.0 mm, 500 microm, and 250 microm are studied. The results demonstrate an approximate 10-fold increase in lane density and a 10-fold reduction in sample size from 5 microL to 500 pL. As a result, the number of theoretical plates has increased 2.5-fold, while system resolution has increased 1.5-fold over the conventional agarose gel systems. An examination of changes in resolution across the width of individual separation lanes in both systems revealed dependence in the case of the conventional gels and no dependence for the gels loaded with the micromachined instrumentation.

76 FR 76935 - Impact of Implementing the Chemical Weapons Convention (CWC) on Commercial Activities Involving...

Science.gov (United States)

2011-12-09

..., titled ``Protection of Advanced Biotechnology,'' calls for the President to certify to Congress on an annual basis that ``the legitimate commercial activities and interests of chemical, biotechnology, and pharmaceutical firms in the United States are not being significantly harmed by the limitations of the Convention...

Historical perspective: The pros and cons of conventional outcome measures in Parkinson's disease.

Science.gov (United States)

Lim, Shen-Yang; Tan, Ai Huey

2018-01-01

Conventional outcome measures (COMs) in Parkinson's disease (PD) refer to rating scales, questionnaires, patient diaries and clinically-based tests that do not require specialized equipment. It is timely at this juncture - as clinicians and researchers begin to grapple with the "invasion" of digital technologies - to review the strengths and weaknesses of these outcome measures. This paper discusses advances (including an enhanced understanding of PD itself, and the development of clinimetrics as a field) that have led to improvements in the COMs used in PD; their strengths and limitations; and factors to consider when selecting and using a measuring instrument. It is envisaged that in the future, a combination of COMs and technology-based objective measures will be utilized, with different methods having their own strengths and weaknesses. Judgement is required on the part of the clinician and researcher in terms of which instrument(s) are appropriate to use, depending on the particular clinical or research setting or question. Copyright © 2017 Elsevier Ltd. All rights reserved.

MR-guided dynamic PET reconstruction with the kernel method and spectral temporal basis functions

Science.gov (United States)

Novosad, Philip; Reader, Andrew J.

2016-06-01

Recent advances in dynamic positron emission tomography (PET) reconstruction have demonstrated that it is possible to achieve markedly improved end-point kinetic parameter maps by incorporating a temporal model of the radiotracer directly into the reconstruction algorithm. In this work we have developed a highly constrained, fully dynamic PET reconstruction algorithm incorporating both spectral analysis temporal basis functions and spatial basis functions derived from the kernel method applied to a co-registered T1-weighted magnetic resonance (MR) image. The dynamic PET image is modelled as a linear combination of spatial and temporal basis functions, and a maximum likelihood estimate for the coefficients can be found using the expectation-maximization (EM) algorithm. Following reconstruction, kinetic fitting using any temporal model of interest can be applied. Based on a BrainWeb T1-weighted MR phantom, we performed a realistic dynamic [18F]FDG simulation study with two noise levels, and investigated the quantitative performance of the proposed reconstruction algorithm, comparing it with reconstructions incorporating either spectral analysis temporal basis functions alone or kernel spatial basis functions alone, as well as with conventional frame-independent reconstruction. Compared to the other reconstruction algorithms, the proposed algorithm achieved superior performance, offering a decrease in spatially averaged pixel-level root-mean-square-error on post-reconstruction kinetic parametric maps in the grey/white matter, as well as in the tumours when they were present on the co-registered MR image. When the tumours were not visible in the MR image, reconstruction with the proposed algorithm performed similarly to reconstruction with spectral temporal basis functions and was superior to both conventional frame-independent reconstruction and frame-independent reconstruction with kernel spatial basis functions. Furthermore, we demonstrate that a joint spectral

Highly sensitive rapid fluorescence detection of protein residues on surgical instruments

International Nuclear Information System (INIS)

Kovalev, Valeri I; Bartona, James S; Richardson, Patricia R; Jones, Anita C

2006-01-01

There is a risk of contamination of surgical instruments by infectious protein residues, in particular, prions which are the agents for Creutzfeldt-Jakob Disease in humans. They are exceptionally resistant to conventional sterilization, therefore it is important to detect their presence as contaminants so that alternative cleaning procedures can be applied. We describe the development of an optimized detection system for fluorescently labelled protein, suitable for in-hospital use. We show that under optimum conditions the technique can detect ∼10 attomole/cm 2 with a scan speed of ∼3-10 cm 2 /s of the test instrument's surface. A theoretical analysis and experimental measurements will be discussed

Reliability and Validity of the Turkish Version of the Job Performance Scale Instrument.

Science.gov (United States)

Harmanci Seren, Arzu Kader; Tuna, Rujnan; Eskin Bacaksiz, Feride

2018-02-01

Objective measurement of the job performance of nursing staff using valid and reliable instruments is important in the evaluation of healthcare quality. A current, valid, and reliable instrument that specifically measures the performance of nurses is required for this purpose. The aim of this study was to determine the validity and reliability of the Turkish version of the Job Performance Instrument. This study used a methodological design and a sample of 240 nurses working at different units in four hospitals in Istanbul, Turkey. A descriptive data form, the Job Performance Scale, and the Employee Performance Scale were used to collect data. Data were analyzed using IBM SPSS Statistics Version 21.0 and LISREL Version 8.51. On the basis of the data analysis, the instrument was revised. Some items were deleted, and subscales were combined. The Turkish version of the Job Performance Instrument was determined to be valid and reliable to measure the performance of nurses. The instrument is suitable for evaluating current nursing roles.

A concept taxonomy and an instrument hierarchy: tools for establishing and evaluating the conceptual framework of a patient-reported outcome (PRO) instrument as applied to product labeling claims.

Science.gov (United States)

Erickson, Pennifer; Willke, Richard; Burke, Laurie

2009-01-01

To facilitate development and evaluation of a PRO instrument conceptual framework, we propose two tools--a PRO concept taxonomy and a PRO instrument hierarchy. FDA's draft guidance on patient reported outcome (PRO) measures states that a clear description of the conceptual framework of an instrument is useful for evaluating its adequacy to support a treatment benefit claim for use in product labeling the draft guidance, however does not propose tools for establishing or evaluating a PRO instrument's conceptual framework. We draw from our review of PRO concepts and instruments that appear in prescription drug labeling approved in the United States from 1997 to 2007. We propose taxonomy terms that define relationships between PRO concepts, including "family,"compound concept," and "singular concept." Based on the range of complexity represented by the concepts, as defined by the taxonomy, we propose nine instrument orders for PRO measurement. The nine orders range from individual event counts to multi-item, multiscale instruments. This analysis of PRO concepts and instruments illustrates that the taxonomy and hierarchy are applicable to PRO concepts across a wide range of therapeutic areas and provide a basis for defining the instrument conceptual framework complexity. Although the utility of these tools in the drug development, review, and approval processes has not yet been demonstrated, these tools could be useful to improve communication and enhance efficiency in the instrument development and review process.

WATCH: Warwick Assessment insTrument for Clinical teacHing: Development and testing.

Science.gov (United States)

Haider, Sonia Ijaz; Johnson, Neil; Thistlethwaite, Jill Elizabeth; Fagan, Gay; Bari, Muhammad Furqan

2015-03-01

Medical education and teaching skills are core competencies included in the generic curriculum for specialty training. To support the development of these skills, there is need for a validated instrument. This study aims to develop and test an instrument to measure the attributes of specialty trainees as effective teachers. The study was conducted in two phases. In first phase, the content of the instrument was generated from the literature and tested using the Delphi technique. In second phase, the instrument was field tested for validity and reliability using factor analysis and generalizability study. Feasibility was calculated by the time taken to complete the instrument. Acceptability and educational impact were determined by qualitative analysis of written feedback. Attributes of specialty trainees were assessed by clinical supervisors, peers, and students. The Delphi study produced consensus on 15 statements which formed the basis of the instrument. In field study, a total of 415 instruments were completed. Factor analysis demonstrated a three-factor solution ('learning-teaching milieu', 'teaching skills', and 'learner-orientated'). A generalizability coefficient was 0.92. Mean time to complete the instrument was five minutes. Feedback indicated that it was an acceptable and useful method of assessment. This new instrument provides valid, reliable, feasible, and acceptable assessment of clinical teaching.

An in vitro study to determine fracture resistance of tooth roots after different instrumentation techniques

Directory of Open Access Journals (Sweden)

Marri Shilpa Reddy

2016-01-01

Conclusion: Preparation of canals with a conventional hand instrumentation technique using 0.02 taper K-files showed highest fracture resistance with least amount of dentin removed at all levels followed by Endowave, ProTaper Hand, and Rotary files.

Signal conditioning circuitry design for instrumentation systems.

Energy Technology Data Exchange (ETDEWEB)

Larsen, Cory A.

2012-01-01

This report details the current progress in the design, implementation, and validation of the signal conditioning circuitry used in a measurement instrumentation system. The purpose of this text is to document the current progress of a particular design in signal conditioning circuitry in an instrumentation system. The input of the signal conditioning circuitry comes from a piezoresistive transducer and the output will be fed to a 250 ksps, 12-bit analog-to-digital converter (ADC) with an input range of 0-5 V. It is assumed that the maximum differential voltage amplitude input from the sensor is 20 mV with an unknown, but presumably high, sensor bandwidth. This text focuses on a specific design; however, the theory is presented in such a way that this text can be used as a basis for future designs.

The evolution and future direction of the Joint Convention on the Safety of Spent Fuel Management and the Safety of Radioactive Waste Management

International Nuclear Information System (INIS)

Siraky, Gabriela

2008-01-01

Full text: The Joint Convention on the Safety of Spent Fuel Management and the Safety of Radioactive Waste Management, namely the Joint Convention, had been established in 1997. The objective of the Convention is to achieve and maintain a high level of safety worldwide in that fields to ensure that there are effective defenses against potential hazards so that individuals, society and the environment are protected from the harmful effects of ionizing radiation and to prevent accidents with radiological consequences and to mitigate their consequences. The Parties to the Convention intend to achieve this objective by international cooperation, peer reviews of each other's performance, assistance when needed for states with less developed programmes and capabilities and the use of internationally accepted standards of safety. The Joint Convention is rooted in the discussions held previously to the establishment of the Convention of the Nuclear Safety that had taken place in the period 1993-1994. The idea of a Convention on the Safety of waste management evolved since then, getting its final status in November 1997 after seven meetings of a specially appointed working group of outstanding specialists on the subject. After that, it was needed three years more until the number of the ratifying States, that then became Contracting Parties, to get the condition that let the Convention to enter into force: ninety days after the date of deposit with the Depository of the twenty-fifth instrument of ratification, acceptance or approval, including the instruments of fifteen States having an operational nuclear power plant. The First Review Meeting was held three years after it entered into force, in November 2003, with the attendance of 33 Parties that presented their National Reports. The second review meeting was held in May 2006. Forty-one Contracting Parties participated in the Second Review Meeting. There is then, a constant evolution in the number of Contracting Parties

First UN member state conference on the climate framework convention

International Nuclear Information System (INIS)

Lamprecht, F.

1995-01-01

The ''Framework Convention of the United Nations Concerning Climate Changes'' (Climate Framework Convention - KRK), which was passed at the 1992 World Environment Conference (UNCEO) in Rio de Janeiro and took effect on 21 March 1994, has instituted the UN Conference of Contracting Parties (VSK) as the organ presiding over this issue (Article 7 KRK). This annual conference has the task to implement the KRK and its associated legal instruments and pass the resolutions required to this end. Its premiere took place in Berlin (28 March to 7 April 1995). Delegates from 117 signatory and 53 observer states struggled before an audience of 2000 news reportes to find a solution to the pending tasks that might be tolerable for all participants. The present article gives a brief outline of these tasks and the results achieved in Berlin. The picture is rounded off by information on the different positions defended, lines of conflict and the course of the conference. (orig.) [de

Apical extrusion of bacteria when using reciprocating single-file and rotary multifile instrumentation systems.

Science.gov (United States)

Tinoco, J M; De-Deus, G; Tinoco, E M B; Saavedra, F; Fidel, R A S; Sassone, L M

2014-06-01

To evaluate ex vivo, apical bacterial extrusion associated with two reciprocating single-file systems (WaveOne and Reciproc) compared with a conventional multifile rotary system (BioRace). Forty-five human single-rooted mandibular incisors were used. Endodontic access cavities were prepared, and root canals were contaminated with an Enterococcus faecalis suspension. Following incubation at 37 °C for thirty days, the contaminated teeth were divided into three groups of 15 specimens each (G1 - Reciproc, G2 - WaveOne and G3 - BioRace). Positive and negative controls consisted of 5 infected teeth and 3 uninfected incisors that were instrumented with one of the tested NiTi systems, respectively. Bacteria extruded from the apical foramen during instrumentation were collected into vials containing 0.9% NaCl. The microbiological samples were taken from the vials and incubated in brain heart agar medium for 24 h. The resulting bacterial titre, in colony-forming units (CFU) per mL, was determined, and these data were analysed by Wilcoxon matched-pairs signed rank test and Kruskal-Wallis H-test. The level of significance was set at α = 0.05. No significant difference was found in the number of CFU between the two reciprocating systems (P = 0.41). The conventional multifile rotary system group was associated with significantly higher CFU than both of the two reciprocating groups (P = 0.01). All instrumentation systems extruded bacteria beyond the foramen. However, both reciprocating single-file systems extruded fewer bacteria apically than the conventional multifile rotary system. © 2013 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Design concepts for a nuclear digital instrumentation and control system platform

International Nuclear Information System (INIS)

Ou, T. C.; Chen, C. K.; Chen, P. J.; Shyu, S. S.; Lee, C. L.; Hsieh, S. F.

2010-10-01

The objective of this paper is to present the development results of the nuclear instrumentation and control system in Taiwan. As the Taiwan nuclear power plants age, the need to consider upgrading of both their safety and non-safety-related instrumentation and control systems becomes more urgent. Meanwhile, the digital instrumentation and control system that is based on current fast evolving electronic and information technologies are difficult to maintain effectively. Therefore, Institute of Nuclear Energy Research was made a decision to promote the Taiwan Nuclear Instrumentation and Control System project to collaborate with domestic electronic industry to establish self-reliant capabilities on the design, manufacturing, and application of nuclear instrumentation and control systems with newer technology. In the case of safety-related applications like nuclear instrumentation and control, safety-oriented quality control is required. In order to establish a generic qualified digital platform, the world-wide licensing experience should be considered in the licensing process. This paper describes the qualification and certification tools by IEC 61508 for design and development of safety related equipment and explains the basis for many decisions made while performing the digital upgrade. (Author)

Costs Associated With Single-Use and Conventional Sets for Distal Radius Plating.

Science.gov (United States)

Fugarino, Bryce; Fox, Mary Patricia; Terhoeve, Cristina; Pappas, Nicholas

2017-11-01

Volar plating of distal radius fractures is an increasingly common procedure. Presterilized, single-use volar plate fixation sets have been purported to increase operating room efficiency and decrease cost. The purpose of this study was to compare the actual cost of using a conventional set compared with the projected cost of using its single-use counterpart. We retrospectively analyzed 30 consecutive cases of volar plate fixation in which conventional instrument sets were used. Hardware and processing costs were calculated for the conventional sets and compared with the projected cost of using single-use sets. The mean total cost of hardware and processing for the conventional sets was $2,728, whereas the projected cost for the single-use sets was slightly higher at $2,868. Twenty-three of the 30 cases would have required additional screws not available in the single-use set. The cost of the additional screws needed to supplement the single-use set would have added an average of $282/case. Overall, the combined hardware and processing cost was lower for conventional sets in 25 of the 30 cases. Although the price of the single-use set is less than the mean charge for use of a conventional set, additional screws not available in the single-use set were required in 77% of cases and consequently rendered the conventional set cheaper in 83% of cases. Stocking the single-use sets with additional screws to reflect the most commonly used screw lengths could make these sets more cost effective in the future. Economic and decision analysis IV. Copyright © 2017 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

A study of the modifications of nuclear instrumentation systems for JRR-2

International Nuclear Information System (INIS)

Azim, Mohammad; Horiki, Ooichiro; Sato, Mitsugu

1978-04-01

In this report a comparative study has been carried out between the original A.M.F. design and the modified design for the nuclear instrumentation systems of the Research Reactor JRR-2, at the Tokai Research Establishment of JAERI. Due to a fire accident in the control room, in July 1968, the originally designed nuclear instrumentation systems, using conventional vacuum tube circuits, were destroyed and were replaced by the modified design, incorporating solid state linear integrated circuits as basic circuit components. The results of the reactor instrumentation systems modification at JRR-2 are very encouraging as the operating efficiency of the Reactor registered an improvement of 43%. Moreover the safety aspects have been fully taken care of in the new design and the reactor is well guarded against all possible instrument failures and human errors. This report presents the basic theory of operation of the two designs alongwith a comparative safety analysis. (auth.)

Post natal use of analgesics: comparisons between conventional postnatal wards and a maternity hotel.

Science.gov (United States)

Nordeng, Hedvig; Eskild, Anne; Nesheim, Britt-Ingjerd

2010-04-01

To investigate factors related to analgesic use after delivery, and especially whether rates of analgesic use were different in a midwife-managed maternity hotel as compared to conventional postnatal wards. One maternity hotel and two conventional postnatal wards at Ullevål University Hospital in Oslo, Norway. Data were obtained from hospital records for 804 women with vaginal deliveries. Postnatal analgesic use. Overall, approximately half the women used analgesics after vaginal delivery in both conventional postnatal wards and maternity hotel. The factors that were significantly associated with use of analgesics postnatally in multivariate analysis were multiparity, having a non-Western ethnicity, smoking in pregnancy, younger age, instrumental delivery, analgesic use during labour, maternal complications post partum, and duration of postnatal stay 4 days or more. The use of analgesics is determined by socio-demographic and obstetric factors rather than the organisation of the ward.

The Development of an ASSA Module as an Auxiliary Tool for Assessment of Existing Plant Instrumentation and enhancement of the instruments performance

International Nuclear Information System (INIS)

Koo, Kil Mo; Kang, Kyung Ho; Ha, Kwang Soon; Cho, Young Ro; Cho, Young; Park, Rae Jun; Kim, Sang Baik; Kim, Hee Dong

2007-04-01

A review of a plant's accident management capabilities is one of the key elements in achieving regulatory closure of severe accident issues. During accidents, information and data from plant's instruments, as well as others sources, are essential for assessing the plant's status and response. Unlike for design basis accidents, there are inherently some uncertainties to instrumentation capabilities for severe accident conditions. There are many ways to obtain information during a severe accident. Moreover, precise measurements are not necessary. The redundancy and ruggedness of a plant's instrumentation provides considerable depth in the capability of existing designs. The circuit simulation analysis and diagnosis methods are used to assess instruments in detail when they give apparently abnormal readings. A new simulator, ASSA(abnormal signal simulator analysis), through an analysis of the important circuits modeling under severe accident conditions has been designed. It has three main functions which are a signal processing tool, an accident management tool, and an additional guide from the initial screen. In this paper, it can be simulated to the temperature characteristic analysis procedure of the ASSA through EQ data comparative method and using specific signal processing under severe accident condition

Examining the global health arena: strengths and weaknesses of a convention approach to global health challenges.

Science.gov (United States)

Haffeld, Just Balstad; Siem, Harald; Røttingen, John-Arne

2010-01-01

The article comprises a conceptual framework to analyze the strengths and weaknesses of a global health convention. The analyses are inspired by Lawrence Gostin's suggested Framework Convention on Global Health. The analytical model takes a starting-point in events tentatively following a logic sequence: Input (global health funding), Processes (coordination, cooperation, accountability, allocation of aid), Output (definition of basic survival needs), Outcome (access to health services), and Impact (health for all). It then examines to what degree binding international regulations can create order in such a sequence of events. We conclude that a global health convention could be an appropriate instrument to deal with some of the problems of global health. We also show that some of the tasks preceding a convention approach might be to muster international support for supra-national health regulations, negotiate compromises between existing stakeholders in the global health arena, and to utilize WHO as a platform for further discussions on a global health convention. © 2010 American Society of Law, Medicine & Ethics, Inc.

Music students: conventional hearing thresholds and at high frequencies

Directory of Open Access Journals (Sweden)

Débora Lüders

2014-07-01

Full Text Available INTRODUCTION: Research has shown that hearing loss in musicians may cause difficulty in timbre recognition and tuning of instruments. AIM: To analyze the hearing thresholds from 250 Hz to 16,000 Hz in a group of music students and compare them to a non-musician group in order to determine whether high-frequency audiometry is a useful tool in the early detection of hearing impairment. METHODS: Study design was a retrospective observational cohort. Conventional and high-frequency audiometry was performed in 42 music students (Madsen Itera II audiometer and TDH39P headphones for conventional audiometry, and HDA 200 headphones for high-frequency audiometry. RESULTS: Of the 42 students, 38.1% were female students and 61.9% were male students, with a mean age of 26 years. At conventional audiometry, 92.85% had hearing thresholds within normal limits; but even within the normal limits, the worst results were observed in the left ear for all frequencies, except for 4000 Hz; compared to the non-musician group, the worst results occurred at 500 Hz in the left ear, and at 250 Hz, 6000 Hz, 9000 Hz, 10,000 Hz, and 11,200 Hz in both the ears. CONCLUSION: The periodic evaluation of high-frequency thresholds may be useful in the early detection of hearing loss in musicians.

Is Open Education a revolution or are MOOCs only marketing instruments?

NARCIS (Netherlands)

Stracke, Christian M.

2017-01-01

This paper presents the current status of Open Education and MOOCs as the main instruments and drivers in the publicity. The evolution from e-Learning towards MOOCs and Open Education is introduced as basis to discuss the main question of this paper: Is Open Education a revolution or are MOOCs only

The Engineering Mechanism in Formation of Informational Basis of Analysis of Financial Sustainability of Enterprise

Directory of Open Access Journals (Sweden)

Chumak Oksana V.

2017-12-01

Full Text Available The article is aimed at substantiating the mechanism and instruments of financial and accountancy engineering with purpose of formation of information support of analysis of financial sustainability in the enterprise management system. The essence and preconditions of introduction of financial and accountancy engineering are disclosed. Expediency of application of the financial engineering mechanism at enterprise while analyzing financial sustainability has been substantiated. An analysis of methods of formation and use of derivative balance reports was carried out. Models of the conception of mechanisms and instruments of financial and accountancy engineering in analyzing the financial sustainability of enterprise have been suggested. A mega-accounts system in the working plan of the enterprise’s accounts has been recommended. Seven iterations have been provided, which constitute the basis of accounting-analytical support of the accountancy engineering. The information obtained on the basis of the financial and accountancy engineering mechanism allows to carry out real assessment of the enterprise’s financial sustainability.

Instruments for reducing the specific fuel consumption of cars; Instrumente zur Absenkung des spezifischen Treibstoffverbrauchs von Personenwagen

Energy Technology Data Exchange (ETDEWEB)

Hammer, S.; Maibach, M. [Infras, Zuerich (Switzerland); Marti, P. [Metron, Brugg (Switzerland)

2001-07-01

This report for the Swiss Federal Office of Energy (SFOE) presents three possible courses of action that are to be taken to reduce the specific fuel consumption of private cars. The report first examines existing targets and the degree to which they have been met up to now, whereby the situation both in Switzerland and in the European Union is looked at. The report makes a suggestion for a future target scenario and elaborates three possible ways to met these targets: regulations on fuel-consumption, a bonus/malus system and tradable certificates. For each of the proposed instruments, the report examines implementation variants and discusses the means for their implementation. The report presents the best models for each of the implementation-variants on the basis of comparisons and the results of evaluations of their effects. For these chosen variants, the authors present comparisons of their effect on fuel consumption in graphical form and recommend tradable certificates as the best instrument.

Cell Attachment Following Instrumentation with Titanium and Plastic Instruments, Diode Laser, and Titanium Brush on Titanium, Titanium-Zirconium, and Zirconia Surfaces.

Science.gov (United States)

Lang, Melissa S; Cerutis, D Roselyn; Miyamoto, Takanari; Nunn, Martha E

2016-01-01

The aim of this study was to evaluate the surface characteristics and gingival fibroblast adhesion of disks composed of implant and abutment materials following brief and repeated instrumentation with instruments commonly used in procedures for implant maintenance, stage-two implant surgery, and periimplantitis treatment. One hundred twenty disks (40 titanium, 40 titaniumzirconium, 40 zirconia) were grouped into treatment categories of instrumentation by plastic curette, titanium curette, diode microlaser, rotary titanium brush, and no treatment. Twenty strokes were applied to half of the disks in the plastic and titanium curette treatment categories, while half of the disks received 100 strokes each to simulate implant maintenance occurring on a repetitive basis. Following analysis of the disks by optical laser profilometry, disks were cultured with human gingival fibroblasts. Cell counts were conducted from scanning electron microscopy (SEM) images. Differences in surface roughness across all instruments tested for zirconia disks were negligible, while both titanium disks and titaniumzirconium disks showed large differences in surface roughness across the spectrum of instruments tested. The rotary titanium brush and the titanium curette yielded the greatest overall mean surface roughness, while the plastic curette yielded the lowest mean surface roughness. The greatest mean cell counts for each disk type were as follows: titanium disks with plastic curettes, titanium-zirconium disks with titanium curettes, and zirconia disks with the diode microlaser. Repeated instrumentation did not result in cumulative changes in surface roughness of implant materials made of titanium, titanium-zirconium, or zirconia. Instrumentation with plastic implant curettes on titanium and zirconia surfaces appeared to be more favorable than titanium implant curettes in terms of gingival fibroblast attachment on these surfaces.

An experiment on rider stability while mounting : comparing middle-aged and elderly cyclists on pedelecs and conventional bicycles.

NARCIS (Netherlands)

Twisk, D.A.M. Platteel, S. & Lovegrove, G.R.

2017-01-01

Pedelecs, popular among elderly cyclists, are associated with a higher injury risk than conventional bicycles. About 17% of these injuries are due to falls while (dis)mounting. Using instrumented bicycles, this study aimed to identify factors contributing to the stability of self-chosen mounting

INSTRUMENTAL CONCEPTUALIZATION SUBJECT AREA SOCIOLOGY: SOME POSSIBLE SOLUTIONS

Directory of Open Access Journals (Sweden)

E. V. Maslennikov

2016-01-01

Full Text Available The article outlines some of the possible ways of integrating the deployment tool conceptualizing domains of sociology on the basis of the machine sets of steps3. Substantiates the urgency of the problem of application of structural constructs of mathematics as a structure-formalism domain of sociology as a combination of theoretical knowledge. Formulated understanding of the sociological dimension in a broad sense of the concept of research as a measurement based on the use of instrumental in conceptualizing the methodology of sociological research. Under instrumental conceptualization refers to the construction of complex conceptual (conceptual schema structurally interconnected relationships between their individual elements, which are the units of the consideration related conceptual integrity, derived from interpretation of the properties “Set” construct. The paper proposes a definition based on the properties set in the scale set by the structure of N. Bourbaki4 relations systems in the data sets under the structural dimension of social phenomena to understand the interpretation of the investigated properties of social phenomena in terms of a construct that lies at the basis of the theoretical model that reflects the diversity of these qualities with the help of conceptual schemes that determine the quality of each as a structure of relations systems (ie, property in these qualities. In conclusion, the article lists presented in a number of publications, some preliminary results of the application of the methodology of conceptualizing instrumental in related disciplines from sociology. These works can perform suggestive role in the knowledge and understanding of methods of problem fields and objectives of the work on the conceptualization of theoretical sociology, using the mathematical theory of forms. 

Flammable gas tank safety program: Technical basis for gas analysis and monitoring

International Nuclear Information System (INIS)

Estey, S.D.

1998-01-01

Several Hanford waste tanks have been observed to exhibit periodic releases of significant quantities of flammable gases. Because potential safety issues have been identified with this type of waste behavior, applicable tanks were equipped with instrumentation offering the capability to continuously monitor gases released from them. This document was written to cover three primary areas: (1) describe the current technical basis for requiring flammable gas monitoring, (2) update the technical basis to include knowledge gained from monitoring the tanks over the last three years, (3) provide the criteria for removal of Standard Hydrogen Monitoring System(s) (SHMS) from a waste tank or termination of other flammable gas monitoring activities in the Hanford Tank farms

France - Convention on Nuclear Safety. Sixth National report for the 2014 review meeting

International Nuclear Information System (INIS)

2013-07-01

The Convention on Nuclear Safety, hereinafter referred to as 'the Convention', is one of the results of international discussions initiated in 1992 in order to contribute to maintaining a high level of nuclear safety worldwide. The convention sets a number of nuclear safety objectives and defines measures to meet them. France signed the Convention on 20 September 1994, the date on which it was opened for signature during the IAEA General Conference, and approved it on 13 September 1995. The Convention entered into force on 24 October 1996. For many years France has been participating actively in international initiatives to enhance nuclear safety. It considers the Convention on Nuclear Safety to be an important instrument for achieving this aim. The areas covered by the Convention have long been part of the French approach to nuclear safety. The purpose of this sixth report, which was drafted pursuant to Article 5 of the Convention and which covers the period 2010 to mid-2013, is to present the measures taken by France in order to fulfil each of its obligations as specified in the said Convention. Since the Convention applies to all nuclear-power generating reactors most of this report is dedicated to the measures taken in order to ensure their safety. However, as in previous reports, France has decided in this sixth report also to present the measures that were taken for all research reactors. First of all, research reactors are actually subject to the same overall regulations as nuclear-power reactors with regard to safety and radiation protection. Then, within the framework of the Joint Convention on the Safety of Spent Fuel Management and the Safety of Radioactive Waste Management, to which France is a Contracting Party, an account was made of the measures taken in those respective fields with regard to research reactors. Lastly, the Board of Governors of the International Atomic Energy Agency (IAEA), of which France is a member, in March 2004 approved the Code

Main features of the convention on supplementary compensation for nuclear damage - an over view

International Nuclear Information System (INIS)

Boulanenkov, V.

2000-01-01

The Chernobyl accident prompted widespread awareness of the need for improved protection of the public from the consequences of nuclear accidents. It was generally recognised that urgent efforts should be undertaken to strengthen the international nuclear liability regime based on two civil law conventions, namely the 1963 Vienna Convention on Civil Liability for Nuclear Damage and the 1960 Paris Convention on Third Party Liability in the Field of Nuclear Energy. The work initiated by the Agency - it was assigned to the Standing Committee established in 1990 - followed a two-track approach: to improve the existing civil liability regime, including revision of the Vienna Convention for which the IAEA is depositary; and, to develop a comprehensive international liability regime. The issue of compensation additional to that available under the two basic conventions received full attention in the negotiations. In the latter context, this work resulted in the adoption by a diplomatic conference convened by the IAEA in September 1997 of a new instrument, i.e. the Convention on Supplementary Compensation for Nuclear Damage (the CSC). The CSC is a product of many years of multilateral negotiations and represents a balance of various legal, economic and political considerations. While not all concerns may have been fully met, it represents a significant improvement in the protection of the public from the consequences of nuclear accidents. (author)

The Effects of NiTi Hand and Rotary Canal Master U and K-Flex Instrumentation of Root Canal Morphology

Science.gov (United States)

1992-09-01

Rotary Canal Master "U" and K-Flex Instrumentation of Root Canal Morphology 6. AUTHOR(S) Robert H. Haller 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES... endodontic failure. B. STATET OF THE PREL]2U Conventional endodontic instruments have re.nained basically unchanged since the introduction of the K-type...F;hcw"e that this nO𔃾 instruneent destim tended ti- produce rounder pr rMticns with • t!-rnnVortaticn than c rnvrnticnal 4 endodontic instruments

Validated finite element analyses of WaveOne Endodontic Instruments: a comparison between M-Wire and NiTi alloys.

Science.gov (United States)

Bonessio, N; Pereira, E S J; Lomiento, G; Arias, A; Bahia, M G A; Buono, V T L; Peters, O A

2015-05-01

To validate torsional analysis, based on finite elements, of WaveOne instruments against in vitro tests and to model the effects of different nickel-titanium (NiTi) materials. WaveOne reciprocating instruments (Small, Primary and Large, n = 8 each, M-Wire) were tested under torsion according to standard ISO 3630-1. Torsional profiles including torque and angle at fracture were determined. Test conditions were reproduced through Finite Element Analysis (FEA) simulations based on micro-CT scans at 10-μm resolution; results were compared to experimental data using analysis of variance and two-sided one sample t-tests. The same simulation was performed on virtual instruments with identical geometry and load condition, based on M-Wire or conventional NiTi alloy. Torsional profiles from FEA simulations were in significant agreement with the in vitro results. Therefore, the models developed in this study were accurate and able to provide reliable simulation of the torsional performance. Stock NiTi files under torsional tests had up to 44.9%, 44.9% and 44.1% less flexibility than virtual M-Wire files at small deflections for Small, Primary and Large instruments, respectively. As deflection levels increased, the differences in flexibility between the two sets of simulated instruments decreased until fracture. Stock NiTi instruments had a torsional fracture resistance up to 10.3%, 8.0% and 7.4% lower than the M-Wire instruments, for the Small, Primary and Large file, respectively. M-Wire instruments benefitted primarily through higher material flexibility while still at low deflection levels, compared with conventional NiTi alloy. At fracture, the instruments did not take complete advantage of the enhanced fractural resistance of the M-Wire material, which determines only limited improvements of the torsional performance. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Heavy metals and other elements in serum of cattle from organic and conventional farms.

Science.gov (United States)

Tomza-Marciniak, Agnieszka; Pilarczyk, Bogumiła; Bąkowska, Małgorzata; Pilarczyk, Renata; Wójcik, Jerzy

2011-11-01

Concentrations of cadmium, lead, iron, zinc, copper, chromium, nickel, aluminium and arsenium were analysed in blood serum of cattle from organic (n=20) and conventional (n=21) farms. The elements were determined by inductively coupled plasma atomic emission spectrometry using an Optima 2000 DV instrument (Perkin Elmer Inc.). Animals from the organic farm were characterised by significantly lower (Panimals from the conventional farm. The concentration of Cd was similar in animals from both organic and conventional farms. The concentration of toxic elements in cattle from organic and conventional farms studied was very low. The trace essential elements were generally within the adequate ranges except Zn and Cu, which were deficient. In organically reared animals, also serum Fe content was below the critical level for diagnosing iron deficiency. Pb was significantly correlated with Cd, Zn, Fe, Cu and Ni. A significant positive correlation between the concentration of Cd and Zn, Cu and Ni concentrations was only observed in cows from the organic farm. The present results suggest that organically raised animals are less exposed to harmful environmental influences such as the environmental pollution with heavy metals. On the other hand, these animals are at a greater risk of mineral deficiency compared to animals kept on conventional farms.

Transposition into swiss law of the Paris convention and the Brussels supplementary convention, as amended

International Nuclear Information System (INIS)

Tami, R.; Daina, S.

2004-01-01

Apart from the considerable increase in the amounts of cover, two basic factors lie behind the Swiss government decision to propose shortly to parliament a draft revised L.R.C.N.(federal act on nuclear third party liability). These are, firstly, that the revised Paris/Brussels system still incorporates the principle of the limited liability of the operator of a nuclear installation but now contains a minimum liability amount (liability threshold) and no longer a maximum amount (liability ceiling), and secondly, that the States parties are allowed to provide in their national legislation for the unlimited liability of operators. One of the aims of ratifying the revised conventions is to enable most victims to obtain fair compensation on an egalitarian basis for damage caused by a nuclear incident, and also to join an international system for compensating nuclear damage based on solidarity between states, most of them nuclear. (N.C.)

A digital, constant-frequency pulsed phase-locked-loop instrument for real-time, absolute ultrasonic phase measurements

Science.gov (United States)

Haldren, H. A.; Perey, D. F.; Yost, W. T.; Cramer, K. E.; Gupta, M. C.

2018-05-01

A digitally controlled instrument for conducting single-frequency and swept-frequency ultrasonic phase measurements has been developed based on a constant-frequency pulsed phase-locked-loop (CFPPLL) design. This instrument uses a pair of direct digital synthesizers to generate an ultrasonically transceived tone-burst and an internal reference wave for phase comparison. Real-time, constant-frequency phase tracking in an interrogated specimen is possible with a resolution of 0.000 38 rad (0.022°), and swept-frequency phase measurements can be obtained. Using phase measurements, an absolute thickness in borosilicate glass is presented to show the instrument's efficacy, and these results are compared to conventional ultrasonic pulse-echo time-of-flight (ToF) measurements. The newly developed instrument predicted the thickness with a mean error of -0.04 μm and a standard deviation of error of 1.35 μm. Additionally, the CFPPLL instrument shows a lower measured phase error in the absence of changing temperature and couplant thickness than high-resolution cross-correlation ToF measurements at a similar signal-to-noise ratio. By showing higher accuracy and precision than conventional pulse-echo ToF measurements and lower phase errors than cross-correlation ToF measurements, the new digitally controlled CFPPLL instrument provides high-resolution absolute ultrasonic velocity or path-length measurements in solids or liquids, as well as tracking of material property changes with high sensitivity. The ability to obtain absolute phase measurements allows for many new applications than possible with previous ultrasonic pulsed phase-locked loop instruments. In addition to improved resolution, swept-frequency phase measurements add useful capability in measuring properties of layered structures, such as bonded joints, or materials which exhibit non-linear frequency-dependent behavior, such as dispersive media.

Magnetization studies in high temperature and conventional superconductors

International Nuclear Information System (INIS)

Grover, A.K.; Chaddah, P.

1991-01-01

In this paper, the authors state the contemporary view of the physical basis of a celebrated phenomenological model for hard superconductors. The authors highlight the qualitative and general predictions of this model relevant to various magnetic measurements. The authors give prescriptions to correlate data of different experiments with the predictions of the model with the intention of extracting information on material parameters, like J c (H), pinning potential, etc. These prescriptions will be illustrated with the data on both conventional and HTSC superconductors. The correlation of these data with the predictions of the model underscores the similarity in behaviour between the two classes of hard superconductors

Highly sensitive rapid fluorescence detection of protein residues on surgical instruments

Energy Technology Data Exchange (ETDEWEB)

Kovalev, Valeri I [School of Engineering and Physical Sciences, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom); Bartona, James S [School of Engineering and Physical Sciences, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom); Richardson, Patricia R [School of Chemistry, University of Edinburgh, Edinburgh, EH9 3JJ (United Kingdom); Jones, Anita C [School of Chemistry, University of Edinburgh, Edinburgh, EH9 3JJ (United Kingdom)

2006-07-15

There is a risk of contamination of surgical instruments by infectious protein residues, in particular, prions which are the agents for Creutzfeldt-Jakob Disease in humans. They are exceptionally resistant to conventional sterilization, therefore it is important to detect their presence as contaminants so that alternative cleaning procedures can be applied. We describe the development of an optimized detection system for fluorescently labelled protein, suitable for in-hospital use. We show that under optimum conditions the technique can detect {approx}10 attomole/cm{sup 2} with a scan speed of {approx}3-10 cm{sup 2}/s of the test instrument's surface. A theoretical analysis and experimental measurements will be discussed.

Application of solar chargers to prospection instruments

International Nuclear Information System (INIS)

Caille, G.

1960-01-01

The use of conventional batteries has certain disadvantages, and for this reason high-voltage batteries have been gradually replaced in all prospection instruments by transistor supply systems, using less cumbersome sources of energy. All the same low voltages are still necessary, and in hot or damp countries the use of these batteries leads to consumptions out of all proportion to the services rendered. This is why the use of solar energy possesses real advantages. After a brief review of the basic ideas on semiconductors, this article describes a selenium solar battery which was developed by the Westinghouse brakes and signals society. (author) [fr

The use of economic instruments for environmental policy: a half-hearted affair

DEFF Research Database (Denmark)

Andersen, Mikael Skou

1995-01-01

their use of economic instruments, but with a few exceptions it has been a somewhat half-hearted affair. Economic imstruments have often been applied on the basis of the principle of the least political resistance. Using Wilson's regulation theory (1980), this paper analyses how the costs and benefits......As a key to a more sustainable development the use of economic instruments for environmental policy has been on the agenda for about eight years. Despite of that, a recent OECD survey recorded only a modest increase in their use since the mid-1980s. In particular the Nordic counries have increased...... of regulations and particular policy-instruments affect the use and design of economic instruments. The outcome has been green taxes that are often fiscally biased , which are too low compared with the externalities they should price and which address the smaller rather than the larger polluters, granting...

Inspector-instrument interface in portable NDA instrumentation

International Nuclear Information System (INIS)

Halbig, J.K.; Klosterbuer, S.F.

1981-01-01

Recent electronics technology advances make it possible to design sophisticated instruments in small packages for convenient field implementation. An inspector-instrument interface design that allows communication of procedures, responses, and results between the instrument and user is presented. This capability has been incorporated into new spent-fuel instrumentation and a battery-powered multichannel analyzer

Inspector-instrument interface in portable NDA instrumentation

International Nuclear Information System (INIS)

Halbig, J.K.; Klosterbuer, S.F.

1981-01-01

Recent electronics technology advances make it possible to design sophisticated instruments in small packages for convenient field implementation. This report describes an inspector-instrument interface design which allows communication of procedures, responses, and results between the instrument and user. The interface has been incorporated into new spent-fuel instrumentation and a battery-powered multichannel analyzer

Structural characterisation and mechanical FE analysis of conventional and M-Wire Ni-Ti alloys used in endodontic rotary instruments.

Science.gov (United States)

Montalvão, Diogo; Alçada, Francisca Sena; Braz Fernandes, Francisco Manuel; de Vilaverde-Correia, Sancho

2014-01-01

The purpose of this study is to understand how the M-Wire alloy conditions the mechanical flexibility of endodontic rotary files at body temperature.Two different rotary instruments, a Profile GT 20/.06 and a Profile GT Series X 20/.06, were selected due to their geometrical similarity and their different constituent alloy. GT series X files are made from M-Wire, a Ni-Ti alloy allegedly having higher flexibility at body temperature. Both files were analysed by X-Ray Diffraction and Differential Scanning Calorimetry to investigate phase transformations and the effects of working temperature on these different alloys. Mechanical behaviour was assessed by means of static bending and torsional Finite Element simulations, taking into account the nonlinear superelastic behaviour of Ni-Ti materials. It was found that GT files present austenitic phase at body temperature, whereas GT series X present R-phase at temperatures under 40 °C with a potential for larger flexibility. For the same load conditions, simulations showed that the slight geometrical differences between the two files do not introduce great disagreement in the instruments' mechanical response. It was confirmed that M-Wire increases the instrument's flexibility, mainly due to the presence of R-phase at body temperature.

Instrument calibration optimization at Bruce Power: ECI loops

International Nuclear Information System (INIS)

Chugh, V.; Angelova, M.; Ghias, S.; Parmar, R.; Wang, V.; Xie, H.; Higgs, J.; Schut, J.; Cruchley, I.

2011-01-01

Most instruments in a nuclear power plant are calibrated at regular intervals to ensure consistency with the assumptions in the plant Technical Specifications and/or Safe Operating Envelope (SOE) compliance limits (e.g., As-Found Tolerance). In the Instrument Uncertainty Calculations (IUC), As-Found Tolerance for instrument drift is estimated based on statistical analysis of As-Found and As-Left calibration data such as that carried out for Bruce NGS by EPRI (Electric Power Research Institute) in 1998. Bruce specific drift values were found to compare favorably with industry benchmarks. Recently a significant amount of work has been done by EPRI and IAEA (International Atomic Energy Agency) on extending calibration intervals of safety related instruments. Reduction in calibration frequency reduces time commitments on the part of Authorized Nuclear Operators and safety system qualified Control Maintenance Technicians, and allows more schedule flexibility. To establish the proof of concept, As-Left/As-Found tolerances and available margins have been evaluated for the Bruce B Emergency Coolant Injection (ECI) system instrument loops to determine whether an extension of the calibration period from one or two year to three years is justifiable on the basis that these loops will still be in compliance with SOE. The analysis showed that 60% of instruments in the ECI system are qualified for calibration interval extension up to three years. Sensitivity assessment of the effect of proposed changes in calibration intervals for 60% of the instruments on the ECI system unavailability has also been performed using the current Bruce Power ECI unavailability model. The results show that, the largest ECI Predicted Future Unavailability (PFU) is 9.2E-4 year/year for in-core LOCA accident. This value is still below the target unavailability of 1.0E-3 year/year. (author)

Instrument calibration optimization at Bruce Power: ECI loops

Energy Technology Data Exchange (ETDEWEB)

Chugh, V.; Angelova, M.; Ghias, S.; Parmar, R.; Wang, V.; Xie, H. [AMEC NSS, Toronto, Ontario (Canada); Higgs, J.; Schut, J.; Cruchley, I. [Bruce Power, Tiverton, Ontario (Canada)

2011-07-01

Most instruments in a nuclear power plant are calibrated at regular intervals to ensure consistency with the assumptions in the plant Technical Specifications and/or Safe Operating Envelope (SOE) compliance limits (e.g., As-Found Tolerance). In the Instrument Uncertainty Calculations (IUC), As-Found Tolerance for instrument drift is estimated based on statistical analysis of As-Found and As-Left calibration data such as that carried out for Bruce NGS by EPRI (Electric Power Research Institute) in 1998. Bruce specific drift values were found to compare favorably with industry benchmarks. Recently a significant amount of work has been done by EPRI and IAEA (International Atomic Energy Agency) on extending calibration intervals of safety related instruments. Reduction in calibration frequency reduces time commitments on the part of Authorized Nuclear Operators and safety system qualified Control Maintenance Technicians, and allows more schedule flexibility. To establish the proof of concept, As-Left/As-Found tolerances and available margins have been evaluated for the Bruce B Emergency Coolant Injection (ECI) system instrument loops to determine whether an extension of the calibration period from one or two year to three years is justifiable on the basis that these loops will still be in compliance with SOE. The analysis showed that 60% of instruments in the ECI system are qualified for calibration interval extension up to three years. Sensitivity assessment of the effect of proposed changes in calibration intervals for 60% of the instruments on the ECI system unavailability has also been performed using the current Bruce Power ECI unavailability model. The results show that, the largest ECI Predicted Future Unavailability (PFU) is 9.2E-4 year/year for in-core LOCA accident. This value is still below the target unavailability of 1.0E-3 year/year. (author)

Evaluation of conventional, protaper hand and protaper rotary instrumentation system for apical extrusion of debris, irrigants and bacteria- An in vitro randomized trial

OpenAIRE

Kalra, Pinky; Rao, Arathi; Suman, Ethel; Shenoy, Ramya; Suprabha, Baranya-Shrikrishna

2017-01-01

Background Endodontic instrumentation carries the risk of over extrusion of debris and bacteria. The technique used and the type of instrumentation influences this risk. Aim The purpose of this study was to evaluate and compare the K-file, ProTaper hand and ProTaper rotary instrumentation systems for the amount of apically extruded debris, irrigant solution and intracanal bacteria. Design Experimental single blinded randomized type of in vitro study with sample of 30 single rooted teeth. Endo...

Economical opportunities on advanced conventional island design for the European pressurized water reactor (EPR) based on Konvoi design. Annex 6

International Nuclear Information System (INIS)

Kremayr, A.; Wagner, K.; Schuberth, U.

2002-01-01

Design of the European Pressurized Water Reactor (EPR) has been finalized by the end of 1998. In parallel with these efforts, the German utilities group contracted the Siemens AG Power generation Group (KWU) to develop an advanced and optimized conventional island for the EPR. The main objectives for improving the conventional island design were determined on the basis of experience of the Konvoi series plants and advanced fossil plants. This paper describes the innovations introduced to the conventional island and presents the reasons for the resultant cost reductions. (author)

Single-incision laparoscopic surgery and conventional laparoscopic treatment of varicocele in adolescents: Comparison between two techniques

Directory of Open Access Journals (Sweden)

Antonio Marte

2014-01-01

Full Text Available Background: Single-incision laparoscopic surgery (SILS has gained great popularity in paediatric surgery due to its minimally invasive approach and improved cosmetic results. Notwithstanding, reports describing its adoption in children are still fragmentary and some perplexities have been raised by some surgeons. We reviewed our experience with the SILS Palomo varicocelectomy procedure (SIL-V in children and adolescents, comparing this group with a similar series operated using conventional laparoscopic varicocelectomy (CL-V. Patients and Methods: A total of 69 Palomo laparoscopic varicocelectomies were performed in patients aged 11-17 years from January 2011 to January 2013. Indications for surgery included grades II-III varicocele or ipsilateral testicular hypotrophy. The SIL-V procedure was performed in 44 patients with roticulating and conventional 5 mm instruments. Testicular vessels were isolated "en bloc," clipped and cut. Operating time, visual analogue scale and post-operative results were compared to a similar group of 25 patients operated with CL-V. Results: No patient of the SIL-V group required conversion to conventional laparoscopy, none to open surgery. Mean operative time was 22 min (range: 19-28 in the SIL-V group, not significantly different compared with CL-V (mean 21 min, range: 18-25. All patients experienced a smooth recovery from surgery without any complications, and were discharged on day 1. No difficulties were found in the SIL-V group. The post-operative pain score was significantly better in SIL-V. Conclusion: The SIL-V procedure is safe and effective and allows a fast and efficient isolation of the vascular bundle. The use of conventional instruments is technically feasible in SIL-V.

Comparative investigation of conventional and R744 auxiliary heating systems in motor cars with low fuel consumption on the basis of a 1.9 l TDI engine; Vergleich konventioneller Zuheizsysteme mit R744-Zuheizsystemen in Automobilen mit geringem Kraftstoffverbrauch auf Basis eines 1,9 l TDI Motors

Energy Technology Data Exchange (ETDEWEB)

Schaefer, B.; Feuerecker, G.; Heinle, D.; Strauss, T. [Behr GmbH und Co. KG, Stuttgart (Germany). Entwicklungszentrum

2003-07-01

The heat emitted by modern consumption-optimized engines, especially diesel engines, is so low that auxiliary heating systems are required for thermal comfort. With R744 air conditioning systems, the air conditioner can be used as auxiliary heating system. The contribution therefore compares conventional PTC and fuel based auxiliary heating systems with three R744 auxiliary heating systems (air-to-air heat pump, coolant-to-air heat pump, and delta process). Simulations were carried out in order to compare heat-up, fuel consumption, and cost. The simulation models were used for calculating demand-oriented heating at different ambient temperatures with a 1.9 l TDI engine. The BEHR software BISS (Behr Integrierte System Simulation) was used as simulation tool. The performance of the heat pump was significantly lower than the performance of conventional auxiliary heating systems at all temperatures. On the other hand, the additional fuel consumption as referred to performance was 15 percent lower than for conventional heating systems. The PTC system had the best cost/profit ratio. (orig.) [German] Der Anteil verbrauchsoptimierter Verbrennungsmotoren, insbesondere Diesel, ist in Europa in den letzten Jahren rasant gestiegen. Die Waermeabgabe dieser Motoren ist inzwischen so niedrig, dass fuer eine rasche und komfortable Aufheizung der Fahrzeugkabine Zuheizsysteme eingesetzt werden muessen. Beim Einsatz von Kohlendioxid (R744) als Kaeltemittel einer Klimaanlage, ist auch ein Betrieb der Klimaanlage als Zuheizsystem denkbar. In diesem Beitrag werden die konventionellen Zuheizsysteme PTC-Zuheizer und Brennstoffzuheizer mit drei R744-Zuheizsystemen mittels Simulation bezueglich Aufheizverhalten, Kraftstoffverbrauch und Kosten bewertet. Die R744 Zuheizsysteme sind Luft-Luft Waermepumpe, Kuehlmittel-Luft-Waermepumpe und Dreiecksprozess. Mit den Simulationsmodellen wurden Berechnungen einer bedarfsorientierten Aufheizung fuer verschiedene Umgebungstemperaturen auf Basis eines

Differences between postmortem computed tomography and conventional autopsy in a stabbing murder case

Directory of Open Access Journals (Sweden)

Talita Zerbini

2014-12-01

Full Text Available Objective: The aim of the present work is to analyze the differences and similarities between the elements of a conventional autopsy and images obtained from postmortem computed tomography in a case of a homicide stab wound. Method: Comparison between the findings of different methods: autopsy and postmortem computed tomography. Results: In some aspects, autopsy is still superior to imaging, especially in relation to external examination and the description of lesion vitality. However, the findings of gas embolism, pneumothorax and pulmonary emphysema and the relationship between the internal path of the instrument of aggression and the entry wound are better demonstrated by postmortem computed tomography. Conclusions: Although multislice computed tomography has greater accuracy than autopsy, we believe that the conventional autopsy method is fundamental for providing evidence in criminal investigations.

Comparison Between Physics and Conventional Forceps in Simple Dental Extraction.

Science.gov (United States)

El-Kenawy, Mohamed H; Ahmed, Wael Mohamed Said

2015-12-01

Atraumatic dental extraction preserves bone, gingival architecture, and allows for the option of future or immediate dental implant placement. A number of tools and techniques have been proposed for minimally invasive tooth removal such as physics forceps. The biomechanical design of physics forceps decreases the incidence of root fracture, and maintains the buccal bone plate, which is essential for the proper healing of an immediately placed dental implant. This study was conducted to evaluate the efficacy of physics forceps versus conventional forceps in simple dental extraction. 200 adult patients seeking simple dental extraction were selected from the Outpatient Clinic in the Oral and Maxillofacial Surgery Department, Faculty of Dentistry, Mansoura University, Egypt. The selected patients were randomly allocated into two groups: group I: included 100 patients, in this group extraction was done using physics forceps, and group II: included 100 patients, in this group extraction was done using conventional forceps. In physics forceps group: crown fracture occurred in three cases (3 %), buccal bone fracture occurred in three cases (3 %), and root fracture occurred in 14 roots (8.5 %), while in conventional forceps group: crown fracture occurred in 10 cases (10 %), buccal bone fracture occurred in seven cases (7 %), and root fracture occurred in 27 roots (16.6 %). Physics forceps are innovative extraction instruments. By using them, it is possible to perform difficult extractions, with predictable results, and without need to reflect a flap. Using physics forceps decreases the incidence of crown, root, and buccal bone plate fractures, in comparison to the conventional forceps.

The Legal Strength of International Health Instruments - What It Brings to Global Health Governance?

Science.gov (United States)

Nikogosian, Haik; Kickbusch, Ilona

2016-09-04

Public health instruments have been under constant development and renewal for decades. International legal instruments, with their binding character and strength, have a special place in this development. The start of the 21st century saw, in particular, the birth of the first World Health Organization (WHO)-era health treaties - the WHO Framework Convention on Tobacco Control (WHO FCTC) and its first Protocol. The authors analyze the potential impact of these instruments on global health governance and public health, beyond the traditional view of their impact on tobacco control. Overall, the very fact that globally binding treaties in modern-era health were feasible has accelerated the debate and expectations for an expanded role of international legal regimes in public health. The impact of treaties has also been notable in global health architecture as the novel instruments required novel institutions to govern their implementation. The legal power of the WHO FCTC has enabled rapid adoption of further instruments to promote its implementation, thus, enhancing the international instrumentarium for health, and it has also prompted stronger role for national legislation on health. Notably, the Convention has elevated several traditionally challenging public health features to the level of international legal obligations. It has also revealed how the legal power of the international health instrument can be utilized in safeguarding the interests of health in the face of competing agendas and legal disputes at both the domestic and international levels. Lastly, the legal power of health instruments is associated with their potential impact not only on health but also beyond; the recently adopted Protocol to Eliminate Illicit Trade in Tobacco Products may best exemplify this matter. The first treaty experiences of the 21st century may provide important lessons for the role of legal instruments in addressing the unfolding challenges in global health. © 2016 The

Environmental potentials of policy instruments to mitigate nutrient emissions in Chinese livestock production

NARCIS (Netherlands)

Zheng, C.; Liu, Y.; Bluemling, B.; Mol, A.P.J.; Chen, J.

2015-01-01

To minimize negative environmental impact of livestock production, policy-makers face a challenge to design and implement more effective policy instruments for livestock farmers at different scales. This research builds an assessment framework on the basis of an agent-based model, named ANEM, to

Introduction to the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management and Canada's participation

International Nuclear Information System (INIS)

Mecke, J.L.

2011-01-01

The Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management (Joint Convention) is the first and the only legally binding international instrument to address safety issues concerning the management of spent fuel and radioactive waste on a global scale. It entered into force on June 18, 2001. The Government of Canada strongly supported international efforts to bring into force the Joint Convention and was the second country to ratify it. The Joint Convention is an 'incentive instrument' that is based on peer review (similar in that respect to the Convention on Nuclear Safety) and devised to encourage countries that are Contracting Parties to report and to foster open and frank discussions on the safety of spent fuel and radioactive waste management. Being an incentive convention, it is not designed to mandate Contracting Parties to fulfill its obligation through control and sanction, but it is based on the common objectives of Contracting Parties to achieve and maintain a high level of safety in spent fuel and radioactive waste management, protect individuals, society and the environment from ionizing radiation and prevent accidents and if necessary mitigating the consequences of such accidents. The following paper will provide an introduction to the Joint Convention and provide a summary of Canada's peer review at the most recent Review Meeting which was held on May 11-20, 2009, at the International Atomic Energy Agency (IAEA) headquarters in Vienna, Austria. (author)

Effect of cyclic torsional preloading on cyclic fatigue resistance of ProTaper Next and Mtwo nickel–titanium instruments

Directory of Open Access Journals (Sweden)

Eugenio Pedullà

2015-06-01

Conclusions: Torsional preloads reduced the cyclic fatigue resistance of M-wire and conventional (as ProTaper Next and Mtwo NiTi rotary instruments except for Mtwo with 25% or 50% of torsional preloading.

Considerations of How to Study Learning Processes when Students Use GIS as an Instrument for Developing Spatial Thinking Skills

Science.gov (United States)

Madsen, Lene Moller; Rump, Camilla

2012-01-01

Within the last 30 years, geographical information systems (GIS) have been used increasingly in the training of geographers. On the basis of the philosophy of technology and instrumental genesis, we sketch how the use of instruments interacts with learning processes and outline how this can be studied. We empirically analyse students' learning…

Instrumentation to Measure the Capacitance of Biosensors by Sinusoidal Wave Method

Directory of Open Access Journals (Sweden)

Pavan Kumar KATHUROJU

2009-09-01

Full Text Available Micro Controller based instrumentation to measure the capacitance of biosensors is developed. It is based on frequency domain technique with sinusoidal wave input. Changes in the capacitance of biosensor because of the analyte specific reaction are calculated by knowing the current flowing through the sample. A dedicated 8-bit microcontroller (AT89C52 and its associated peripherals are employed for the hardware and application specific software is developed in ‘C’ language. The paper describes the methodology, instrumentation details along with a specific application to glucose sensing. The measurements are conducted with glucose oxidase based capacitance biosensor and the obtained results are compared with the conventional method of sugar measurements using the UV-Visible spectroscopy (Phenol-Sulphuric acid assay method. Measurement accuracy of the instrument is found to be ± 5 %. Experiments are conducted on glucose sensor with different bias voltages. It is found that for bias voltages varying from 0.5 to 0.7 Volt, the measurements are good for this application.

Estimating the CCSD basis-set limit energy from small basis sets: basis-set extrapolations vs additivity schemes

Energy Technology Data Exchange (ETDEWEB)

Spackman, Peter R.; Karton, Amir, E-mail: amir.karton@uwa.edu.au [School of Chemistry and Biochemistry, The University of Western Australia, Perth, WA 6009 (Australia)

2015-05-15

Coupled cluster calculations with all single and double excitations (CCSD) converge exceedingly slowly with the size of the one-particle basis set. We assess the performance of a number of approaches for obtaining CCSD correlation energies close to the complete basis-set limit in conjunction with relatively small DZ and TZ basis sets. These include global and system-dependent extrapolations based on the A + B/L{sup α} two-point extrapolation formula, and the well-known additivity approach that uses an MP2-based basis-set-correction term. We show that the basis set convergence rate can change dramatically between different systems(e.g.it is slower for molecules with polar bonds and/or second-row elements). The system-dependent basis-set extrapolation scheme, in which unique basis-set extrapolation exponents for each system are obtained from lower-cost MP2 calculations, significantly accelerates the basis-set convergence relative to the global extrapolations. Nevertheless, we find that the simple MP2-based basis-set additivity scheme outperforms the extrapolation approaches. For example, the following root-mean-squared deviations are obtained for the 140 basis-set limit CCSD atomization energies in the W4-11 database: 9.1 (global extrapolation), 3.7 (system-dependent extrapolation), and 2.4 (additivity scheme) kJ mol{sup –1}. The CCSD energy in these approximations is obtained from basis sets of up to TZ quality and the latter two approaches require additional MP2 calculations with basis sets of up to QZ quality. We also assess the performance of the basis-set extrapolations and additivity schemes for a set of 20 basis-set limit CCSD atomization energies of larger molecules including amino acids, DNA/RNA bases, aromatic compounds, and platonic hydrocarbon cages. We obtain the following RMSDs for the above methods: 10.2 (global extrapolation), 5.7 (system-dependent extrapolation), and 2.9 (additivity scheme) kJ mol{sup –1}.

Estimating the CCSD basis-set limit energy from small basis sets: basis-set extrapolations vs additivity schemes

International Nuclear Information System (INIS)

Spackman, Peter R.; Karton, Amir

2015-01-01

Coupled cluster calculations with all single and double excitations (CCSD) converge exceedingly slowly with the size of the one-particle basis set. We assess the performance of a number of approaches for obtaining CCSD correlation energies close to the complete basis-set limit in conjunction with relatively small DZ and TZ basis sets. These include global and system-dependent extrapolations based on the A + B/L α two-point extrapolation formula, and the well-known additivity approach that uses an MP2-based basis-set-correction term. We show that the basis set convergence rate can change dramatically between different systems(e.g.it is slower for molecules with polar bonds and/or second-row elements). The system-dependent basis-set extrapolation scheme, in which unique basis-set extrapolation exponents for each system are obtained from lower-cost MP2 calculations, significantly accelerates the basis-set convergence relative to the global extrapolations. Nevertheless, we find that the simple MP2-based basis-set additivity scheme outperforms the extrapolation approaches. For example, the following root-mean-squared deviations are obtained for the 140 basis-set limit CCSD atomization energies in the W4-11 database: 9.1 (global extrapolation), 3.7 (system-dependent extrapolation), and 2.4 (additivity scheme) kJ mol –1 . The CCSD energy in these approximations is obtained from basis sets of up to TZ quality and the latter two approaches require additional MP2 calculations with basis sets of up to QZ quality. We also assess the performance of the basis-set extrapolations and additivity schemes for a set of 20 basis-set limit CCSD atomization energies of larger molecules including amino acids, DNA/RNA bases, aromatic compounds, and platonic hydrocarbon cages. We obtain the following RMSDs for the above methods: 10.2 (global extrapolation), 5.7 (system-dependent extrapolation), and 2.9 (additivity scheme) kJ mol –1

Design, Modelling and Teleoperation of a 2 mm Diameter Compliant Instrument for the da Vinci Platform.

Science.gov (United States)

Francis, P; Eastwood, K W; Bodani, V; Looi, T; Drake, J M

2018-05-07

This work explores the feasibility of creating and accurately controlling an instrument for robotic surgery with a 2 mm diameter and a three degree-of-freedom (DoF) wrist which is compatible with the da Vinci platform. The instrument's wrist is composed of a two DoF bending notched-nitinol tube pattern, for which a kinematic model has been developed. A base mechanism for controlling the wrist is designed for integration with the da Vinci Research Kit. A basic teleoperation task is successfully performed using two of the miniature instruments. The performance and accuracy of the instrument suggest that creating and accurately controlling a 2 mm diameter instrument is feasible and the design and modelling proposed in this work provide a basis for future miniature instrument development.

Music students: conventional hearing thresholds and at high frequencies.

Science.gov (United States)

Lüders, Débora; Gonçalves, Cláudia Giglio de Oliveira; Lacerda, Adriana Bender de Moreira; Ribas, Ângela; Conto, Juliana de

2014-01-01

Research has shown that hearing loss in musicians may cause difficulty in timbre recognition and tuning of instruments. To analyze the hearing thresholds from 250 Hz to 16,000 Hz in a group of music students and compare them to a non-musician group in order to determine whether high-frequency audiometry is a useful tool in the early detection of hearing impairment. Study design was a retrospective observational cohort. Conventional and high-frequency audiometry was performed in 42 music students (Madsen Itera II audiometer and TDH39P headphones for conventional audiometry, and HDA 200 headphones for high-frequency audiometry). Of the 42 students, 38.1% were female students and 61.9% were male students, with a mean age of 26 years. At conventional audiometry, 92.85% had hearing thresholds within normal limits; but even within the normal limits, the worst results were observed in the left ear for all frequencies, except for 4000 Hz; compared to the non-musician group, the worst results occurred at 500 Hz in the left ear, and at 250 Hz, 6000 Hz, 9000 Hz, 10,000 Hz, and 11,200 Hz in both the ears. The periodic evaluation of high-frequency thresholds may be useful in the early detection of hearing loss in musicians. Copyright © 2014 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

BGO front-end electronics and signal processing in the MXGS instrument for the ASIM mission

DEFF Research Database (Denmark)

Skogseide, Yngve; Cenkeramaddi, Linga Reddy; Genov, Georgi

2012-01-01

This paper presents the Bismuth Germanate Oxide (BGO) front-end electronics design and signal processing in Modular X- and Gamma ray sensor (MXGS) instrument onboard the Atmosphere Space Interaction Monitor (ASIM) mission, funded by the European Space Agency. University of Bergen is responsible...... for the design and development of the detector layers and readout electronics for the MXGS instrument. The principal objective of the instrument is to detect Terrestrial Gamma ray Flashes (TGFs), which are related to thunderstorm activity. The digital pulse processing scheme used in the MXGS BGO detector gives...... it a significantly higher rate capability than what has been achieved in other instruments used in the study of terrestrial gamma flashes. The front-end electronics for the BGO detector layer in MXGS system also uses fewer components compared to conventional analog front-ends for BGO detectors, thereby increasing...

Quality control of nuclear medicine instruments

International Nuclear Information System (INIS)

1984-11-01

This document, which gives detailed guidance on the quality control of the various electronic instruments used for radiation detection and measurement in nuclear medicine, stems from the work of two Advisory Groups convened by the International Atomic Energy Agency (IAEA). A preliminary document, including recommended test schedules but lacking actual protocols for the tests, was drawn up by the first of these groups, meeting at the IAEA Headquarters in Vienna in 1979. A revised and extended version, incorporating recommended test protocols, was prepared by the second Group, meeting likewise in Vienna in 1982. This version is the model for the present text. The document should be of value to all nuclear medicine units, and especially to those in developing countries, in the initiation or revision of schemes for the quality control of their instruments. Its recommendations have provided the basis for instruction in two IAEA regional technical co-operation projects in the subject field, one initiated in 1981 for countries of Latin America and one initiated in 1982 for countries of Asia and the Pacific

The Role of International Law: Formulating International Legal Instruments and Creating International Institutions.

Science.gov (United States)

Szasz, Paul C.

1991-01-01

Using as a basis the threat of climatic change resulting from global warming, this article considers the functions that might be assigned to an international regime. For each function individually and collectively, the instruments and institutions that would be required for the various processes are examined. (SLD)

Effects and practices on nuclear safety convention promoting nuclear safety in China

International Nuclear Information System (INIS)

Zhang Wei; Cheng Jianxiu; Chen Maosong

2010-01-01

By the means of peer review and self-review, the Contracting Parties are reviewed on obligations under the Convention. In order to implementation these, the State Department established the specific group, under the efforts of departments together, the China fulfilled the obligations successfully. The international society affirmed the good practices on nuclear safety in China, at the same time, they pointed out some fields that China pay close attention to. On the basis of analyzing questions, we point out some aspects which are combined the common questions put forward by the International Atomic Energy Agency on the 4th reviewing meeting that the Chinese government pay close attention to on the next review meeting. Meanwhile, we also put forward some suggestions on how to do better on fulfilling the convention. (authors)

The contextual effects of social capital on health: a cross-national instrumental variable analysis.

Science.gov (United States)

Kim, Daniel; Baum, Christopher F; Ganz, Michael L; Subramanian, S V; Kawachi, Ichiro

2011-12-01

Past research on the associations between area-level/contextual social capital and health has produced conflicting evidence. However, interpreting this rapidly growing literature is difficult because estimates using conventional regression are prone to major sources of bias including residual confounding and reverse causation. Instrumental variable (IV) analysis can reduce such bias. Using data on up to 167,344 adults in 64 nations in the European and World Values Surveys and applying IV and ordinary least squares (OLS) regression, we estimated the contextual effects of country-level social trust on individual self-rated health. We further explored whether these associations varied by gender and individual levels of trust. Using OLS regression, we found higher average country-level trust to be associated with better self-rated health in both women and men. Instrumental variable analysis yielded qualitatively similar results, although the estimates were more than double in size in both sexes when country population density and corruption were used as instruments. The estimated health effects of raising the percentage of a country's population that trusts others by 10 percentage points were at least as large as the estimated health effects of an individual developing trust in others. These findings were robust to alternative model specifications and instruments. Conventional regression and to a lesser extent IV analysis suggested that these associations are more salient in women and in women reporting social trust. In a large cross-national study, our findings, including those using instrumental variables, support the presence of beneficial effects of higher country-level trust on self-rated health. Previous findings for contextual social capital using traditional regression may have underestimated the true associations. Given the close linkages between self-rated health and all-cause mortality, the public health gains from raising social capital within and across

Technical basis and radiological release plan for Trackhoes used at 100 BC-1 and 100 DR-1

International Nuclear Information System (INIS)

De Mers, S.K.

1997-06-01

To develop a method for the radiological release of tracked heavy equipment vehicles used in the excavation of the 100-BC-1 and 100-DR remedial action sites, including the technical basis for selection of release criteria and the instrumentation to be used for surveys

Nuclear safety: an international approach: the convention on nuclear safety

International Nuclear Information System (INIS)

Rosen, M.

1994-01-01

This paper is a general presentation of the IAEA Convention on Nuclear Safety which has already be signed by 50 countries and which is the first legal instrument that directly addresses the safety of nuclear power plants worldwide. The paper gives a review of its development and some key provisions for a better understanding of how this agreement will operate in practice. The Convention consists of an introductory preamble and four chapters consisting of 35 articles dealing with: the principal objectives, definitions and scope of application; the various obligations (general provisions, legislation, responsibility and regulation, general safety considerations taking into account: the financial and human resources, the human factors, the quality assurance, the assessment and verification of safety, the radiation protection and the emergency preparedness; the safety of installations: sitting, design and construction, operation); the periodic meetings of the contracting parties to review national reports on the measures taken to implement each of the obligations, and the final clauses and other judicial provisions common to international agreements. (J.S.). 1 append

[Treatment of a fractured endodontical instrument in the root canal].

Science.gov (United States)

Schipper, M; Peters, L B

2015-12-01

A 53-year-old woman with continuing pain coming from a lower first molar was diagnosed with apical periodontitis, with a retained fractured instrument in the root canal. There are a variety of treatment options for dealing with a corpus alienum in a root canal. In this case it was decided to treat the tooth endodontically, and leave the fractured instrument fragment in situ. The selection of this treatment option was made on the basis of knowledge of the original diagnosis and the success rates of the various treatment options as described in the relevant literature, weighed against the possible risks and their effects on the prognosis. This suggested that the use of a dental operating microscope has a positive impact on the success rates of endodontic treatment The prognosis for endodontic treatment when a fractured instrument fragment is left within the root canal, as in this case, is not significantly reduced. The presence of preoperative periapical pathology, however, is a more clinically significant prognostic indicator.

Recent development in analytical methodology on the ANL 300 kV instrument

International Nuclear Information System (INIS)

Zaluzec, N.J.

2003-01-01

Full text: The advantages of field emission gun (FEG) based medium voltage instruments has been described for many years in terms of the increased spatial and image 'resolution' that can be obtained. Many laboratories have pressed the instruments to reach their highest resolution capabilities, but in doing so at a sacrifice of other parameters and/or capabilities which are equally important to solving real world problems. We have instead chosen to use the ANL instrument as an electron-optical bench to explore novel imaging and analysis modes, which in a conventional machine are not always readily achievable. These include operation in Lorentz and Stem, Position Resolved Diffraction, Scanning Confocal, and most recently high count rate XEDS mode using a new design of SDD EDS system. The results from these studies will be presented and then extended to their application in typical materials problems. Copyright (2003) Australian Microbeam Analysis Society

Randomized clinical study comparing piezosurgery and conventional rotatory surgery in mandibular cyst enucleation.

Science.gov (United States)

Pappalardo, Sabrina; Guarnieri, Renzo

2014-07-01

The aim of the present study is to compare piezoelectric surgery to the conventional rotatory surgery in mandibular cyst enucleation, and to determine the 2 method's suitability and the postoperative outcomes. Eighty patients were included in the study. 35 male and 45 female, which showed cystic mandibular lesions, compared with the inferior alveolar nerve or the mental nerve. The patients were randomly divided into two groups. In the test group, cystectomy was performed using conventional rotatory instrumentation (rotatory-group), and in the other one piezoelectric surgery (piezo-group). The swelling was documented 24/48/72 h and 1 week post-surgery and the patients recorded their subjective postoperative pain daily for 7 days using a Visual Analog Scale (VAS). Patients treated with piezoelectric technique have presented a lower VAS, minor swelling and less recovery time compared to the rotatory-group. No lesions of the mandible nerve were detected with piezosurgery whereas surgery with rotary instruments resulted in 8% hypesthesia at least up to one week. The results of this study suggest that piezosurgery may be considered effective in cyst enucleation compared to traditional procedures with burs, since it grants the patients significantly less post-surgical pain and swelling. Copyright © 2013 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

The Conventional and Unconventional about Disability Conventions: A Reflective Analysis of United Nations Convention on the Rights of Persons with Disabilities

Science.gov (United States)

Umeasiegbu, Veronica I.; Bishop, Malachy; Mpofu, Elias

2013-01-01

This article presents an analysis of the United Nations Convention on the Rights of Persons with Disabilities (CRPD) in relation to prior United Nations conventions on disability and U.S. disability policy law with a view to identifying the conventional and also the incremental advances of the CRPD. Previous United Nations conventions related to…

Instrumentation

International Nuclear Information System (INIS)

Prieur, G.; Nadi, M.; Hedjiedj, A.; Weber, S.

1995-01-01

This second chapter on instrumentation gives little general consideration on history and classification of instrumentation, and two specific states of the art. The first one concerns NMR (block diagram of instrumentation chain with details on the magnets, gradients, probes, reception unit). The first one concerns precision instrumentation (optical fiber gyro-meter and scanning electron microscope), and its data processing tools (programmability, VXI standard and its history). The chapter ends with future trends on smart sensors and Field Emission Displays. (D.L.). Refs., figs

Revision of the Paris Convention and the Brussels Supplementary Convention

International Nuclear Information System (INIS)

Busekist, Otto von.

1977-01-01

The Paris Convention and the Brussels Supplementary Convention have in substance remained unchanged since their adoption in 1960 and 1963, respectively. During that period, nuclear industry and technology have developed considerably while the financial and monetary bases of the Conventions have been shattered. The amounts of liability and compensation have been eroded by inflation, and the gold-based unit of account in which these amounts are expressed has lost its original meaning after the abolition of the official gold price. The question of revising the Conventions, in particular of raising those amounts and of replacing the unit of account, is therefore being studied by the Group of Governmental Experts on Third party Liability in the Field of Nuclear Energy of the OECD Nuclear Energy Agency. (auth.) [fr

RoboSCell: An automated single cell arraying and analysis instrument

KAUST Repository

Sakaki, Kelly

2009-09-09

Single cell research has the potential to revolutionize experimental methods in biomedical sciences and contribute to clinical practices. Recent studies suggest analysis of single cells reveals novel features of intracellular processes, cell-to-cell interactions and cell structure. The methods of single cell analysis require mechanical resolution and accuracy that is not possible using conventional techniques. Robotic instruments and novel microdevices can achieve higher throughput and repeatability; however, the development of such instrumentation is a formidable task. A void exists in the state-of-the-art for automated analysis of single cells. With the increase in interest in single cell analyses in stem cell and cancer research the ability to facilitate higher throughput and repeatable procedures is necessary. In this paper, a high-throughput, single cell microarray-based robotic instrument, called the RoboSCell, is described. The proposed instrument employs a partially transparent single cell microarray (SCM) integrated with a robotic biomanipulator for in vitro analyses of live single cells trapped at the array sites. Cells, labeled with immunomagnetic particles, are captured at the array sites by channeling magnetic fields through encapsulated permalloy channels in the SCM. The RoboSCell is capable of systematically scanning the captured cells temporarily immobilized at the array sites and using optical methods to repeatedly measure extracellular and intracellular characteristics over time. The instrument\\'s capabilities are demonstrated by arraying human T lymphocytes and measuring the uptake dynamics of calcein acetoxymethylester-all in a fully automated fashion. © 2009 Springer Science+Business Media, LLC.

A basic design of SR4 instrumentation and control system for research reactor

International Nuclear Information System (INIS)

Syahrudin Yusuf; M Subhan; Ikhsan Shobari; Sutomo Budihardjo

2010-01-01

An SR4 instrumentation and control systems of research reactor is the equipment of nuclear research reactors as power protection devices and control systems. The equipment is to monitor safety parameters and process parameters in the state of reactor shut down, start-up, and in operation at fixed power. In the engineering of Instrumentation and control systems SR4 research reactor, its basic design consists of technical specifications of the reactor protection system devices, technical specifications of the reactor power control system devices, technical specifications information system devices, and systems process termination cabling as a support system. This basic design is used as the basis for the preparation of detailed design and subsequent engineering development of instrumentation systems and control system integrated. (author)

Draft American National Standard N42.17A: performance specifications for health physics instrumentation

International Nuclear Information System (INIS)

Selby, J.M.

1984-07-01

The report describes the history of the development of the N42.17 standard on instrument performance, describes the standard itself and its relationship to other standards, and discusses ways the standards might be used on either a voluntary or semi-voluntary basis

Instrumentation

Energy Technology Data Exchange (ETDEWEB)

Decreton, M

2001-04-01

SCK-CEN's research and development programme on instrumentation involves the assessment and the development of sensitive measurement systems used within a radiation environment. Particular emphasis is on the assessment of optical fibre components and their adaptability to radiation environments. The evaluation of ageing processes of instrumentation in fission plants, the development of specific data evaluation strategies to compensate for ageing induced degradation of sensors and cable performance form part of these activities. In 2000, particular emphasis was on in-core reactor instrumentation applied to fusion, accelerator driven and water-cooled fission reactors. This involved the development of high performance instrumentation for irradiation experiments in the BR2 reactor in support of new instrumentation needs for MYRRHA, and for diagnostic systems for the ITER reactor.

Instrumentation

International Nuclear Information System (INIS)

Decreton, M.

2001-01-01

SCK-CEN's research and development programme on instrumentation involves the assessment and the development of sensitive measurement systems used within a radiation environment. Particular emphasis is on the assessment of optical fibre components and their adaptability to radiation environments. The evaluation of ageing processes of instrumentation in fission plants, the development of specific data evaluation strategies to compensate for ageing induced degradation of sensors and cable performance form part of these activities. In 2000, particular emphasis was on in-core reactor instrumentation applied to fusion, accelerator driven and water-cooled fission reactors. This involved the development of high performance instrumentation for irradiation experiments in the BR2 reactor in support of new instrumentation needs for MYRRHA, and for diagnostic systems for the ITER reactor

REFORMASI SISTEM AKUNTANSI CASH BASIS MENUJU SISTEM AKUNTANSI ACCRUAL BASIS

Directory of Open Access Journals (Sweden)

Yuri Rahayu

2016-03-01

Full Text Available Abstract –  Accounting reform movement was born with the aim of structuring the direction of improvement . This movement is characterized by the enactment of the Act of 2003 and Act 1 of 2004, which became the basis of the birth of Government Regulation No.24 of 2005 on Government Accounting Standards ( SAP . The general,  accounting is based on two systems,  the cash basis  and the accrual basis. The facts speak far students still at problem with differences to the two methods that result in a lack of understanding on the treatment system for recording. The purpose method of research is particularly relevant to student references who are learning basic accounting so that it can provide information and more meaningful understanding of the accounting method cash basis and Accrual basis. This research was conducted through a normative approach, by tracing the document that references a study/library that combines source of reference that can be believed either from books and the internet are processed with a foundation of knowledge and experience of the author. The conclusion can be drawn that basically to be able to understand the difference of the system and the Cash Basis accrual student base treatment requires an understanding of both methods. To be able to have the ability and understanding of both systems required reading exercises and reference sources.   Keywords : Reform, cash basis, accrual basis   Abstrak - Gerakan reformasi akuntansi dilahirkan dengan tujuan penataan ke arah perbaikan. Gerakan ini  ditandai dengan dikeluarkannya  Undang-Undang tahun 2003 dan Undang-Undang No.1 Tahun 2004  yang menjadi dasar lahirnya Peraturan Pemerintah No.24 Tahun 2005 tentang Standar Akuntansi Pemerintah (SAP . Pada umumnya pencatatan akuntansi di dasarkan pada dua sistem yaitu basis kas (Cash Basis dan basis akrual  (Accrual Basis. Fakta berbicara Selama ini mahasiswa masih dibinggungkan dengan perbedaan ke dua metode itu sehingga

The role of the IAEA in the London Convention 1972 on Dumping of Wastes at Sea

International Nuclear Information System (INIS)

Telleria, Diego; Berkovsky, Volodymyr; Jova Sed, Luis; Louvat, Didier

2008-01-01

Full text: The Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter was adopted after an Inter-Governmental Conference, held in London in 1972, following the principles for environmental protection enunciated in the Report of the United Nations Conference on Human Environment, held the same year in Stockholm. The IAEA has been involved since the early days of the London Convention when the Contracting Parties designated the IAEA as the competent international authority in matters related to sea disposal of radioactive waste, providing technical advice and services. The IAEA developed, for the Convention, the definition of 'radioactive wastes or radioactive matters unsuitable for dumping at sea' (e.g., high level radioactive waste) and recommended the technical basis applicable by the national authorities to issue special permits for those radioactive materials which could be dumped (mainly low and intermediate level radioactive waste, properly conditioned and 'de minimis' quantities). However, in 1985, based more on political reasons than on the existing radiation protection principles and policies, the Contracting Parties to the London Convention introduced a 'voluntary moratorium' on the disposal of low level radioactive wastes at sea, and later in 1993, a total ban of radioactive waste disposal at sea. The IAEA continues to support the objectives of the London Convention by providing scientific advice. Since 1989, at the request of the Contracting Parties, the IAEA has developed and maintained global databases on radioactive waste disposed of at sea in the past and on accidents and losses at sea involving radioactive material. The purpose of these databases is to serve as the basis for radiological impact assessment on the marine environment. The last revised reports on the above mentioned inventories were published in 1999 and in 2001 respectively. The databases are currently in the process of being updated. The paper presents

Performing instrumentation and controls upgrades

International Nuclear Information System (INIS)

Kessler, F. M.; Connell, T. J.; Ryan, M. P.

1992-01-01

I and C upgrades are comprised of a varying range of content, complexity, expansiveness, and criticality. There are common threads in all upgrades which can be simplified by the development of a long term I and C upgrade plan. The development of a such a plan can establish effective ground rules for upgrades, large and small. It can be the basis from which to begin an upgrade evaluation and the standard which is used to compare the degree of compliance of any upgrade regarding the plan or to define the differences from the plan and an individual upgrade. Primary motivation for I and C upgrades are obsolescence and unavailability of spare parts. Numerous other areas of consideration are also involved in an upgrade. Today's technology results in most upgrades largely or totally utilizing digital equipment. The use of digital equipment is fairly new in many I and C applications and requires an elaborate evaluation from functional, qualification, operational, and licensing perspectives as well as others. A well defined upgrade plan developed as a basis for I and C upgrades is a significant start to ensuring an effective upgrade process. Properly developed and implemented, the plan will support I and C upgrade efforts to ensure that the intricacies associated with such tasks eliminate the existing problems which require the upgrade to be performed. The upgrade plan also results in ensuring the maximum benefit from all perspectives of the plant enhancements being carried out and considered for future implementation. Instrumentation and controls aging and replacement are issues of growing importance due to the potential for significant impact on plant operation and efficiency. Obsolescence and unavailability of spare parts are major drivers towards evaluating the cost benefits of upgrading current equipment. In addition to these two primary factors, the advantages of utilizing digital equipment have also become of prime importance when evaluating instrumentation and

Portable musical instrument amplifier

Science.gov (United States)

Christian, David E.

1990-07-24

The present invention relates to a musical instrument amplifier which is particularly useful for electric guitars. The amplifier has a rigid body for housing both the electronic system for amplifying and processing signals from the guitar and the system's power supply. An input plug connected to and projecting from the body is electrically coupled to the signal amplifying and processing system. When the plug is inserted into an output jack for an electric guitar, the body is rigidly carried by the guitar, and the guitar is operatively connected to the electrical amplifying and signal processing system without use of a loose interconnection cable. The amplifier is provided with an output jack, into which headphones are plugged to receive amplified signals from the guitar. By eliminating the conventional interconnection cable, the amplifier of the present invention can be used by musicians with increased flexibility and greater freedom of movement.

THE DEVELOPMENT OF AN INSTRUMENT FOR MEASURING THE UNDERSTANDING OF PROFIT-MAXIMIZING PRINCIPLES.

Science.gov (United States)

MCCORMICK, FLOYD G.

THE PURPOSE OF THE STUDY WAS TO DEVELOP AN INSTRUMENT FOR MEASURING PROFIT-MAXIMIZING PRINCIPLES IN FARM MANAGEMENT WITH IMPLICATIONS FOR VOCATIONAL AGRICULTURE. PRINCIPLES WERE IDENTIFIED FROM LITERATURE SELECTED BY AGRICULTURAL ECONOMISTS. FORTY-FIVE MULTIPLE-CHOICE QUESTIONS WERE REFINED ON THE BASIS OF RESULTS OF THREE PRETESTS AND…

Evaluation tests of the Instrumentation and Control equipment to use in nuclear power plants: its contribution to the improvement and quality certification of the Brazilian equipment

International Nuclear Information System (INIS)

Menezes, R.H.M. de; Peluso, M.A.V.

1984-01-01

This work presents the procedures used to evaluate Instrumentation Control equipment and reports the experience of integration among instrument user, manufacturer and test institution. It covers tests for equipments for conventional user and for specific application in Nuclear Power Stations. (Author) [pt

General and preliminary thermohydraulic, hydrogen and aerosol instrumentation plan for the Phebus Fp-project

International Nuclear Information System (INIS)

Hampel, G.; Poss, G.; Frohlich, H.K.

1989-10-01

The objective of the project was to draw up an instrumentation plan for the French core melting programme PHEBUS FP. This instrumentation plan essentially was to include proven and reliable instruments for recording various thermohydraulic, aerosol and hydrogen phenomena. The candidate measuring methods, which are known mainly from reactor safety programmes, have been described and examined for their usefulness in PHEBUS. Each method and instrument has been described in detail under various aspects such as measuring principle, measuring range, technical design, evaluation model, calibration procedure, accuracy, previous experience, commercial availability, etc. Special attention has been paid to the behaviour of the measuring transducers when exposed to radiation. First, the performance of the instruments was compared with the requirements of PHEBUS. The results of this comparison served as the basis for a measuring concept in tabular form, giving the locations of the measurements, the measuring tasks, and the number and kind of instruments that are recommended. Redundancy and cost-benefit aspects have been taken into account in qualitative terms

The installation and operation of the seismic instrumentation in Korean NPPs

International Nuclear Information System (INIS)

Lee, Kye Hyun; Baek, Yong Lak; Chung, Yun Suk

1994-01-01

Including the 7 October, 1978, Hongsung earthquake, many earthquakes have occurred in our country. The Korean peninsular is no longer a safety zone against earthquakes, and there are possibilities of the damage they cause. So therefore, it is essential to verify the safety of the safety-related facilities in the event of an earthquake. If an earthquake occurs, seismic instrumentation provides information on the vibratory ground motion and resultant vibratory responses of representative safety-related structures and equipment so that an evaluation can be made immediately as to whether or not the design response spectra have been exceeded. In this paper, general descriptions of the seismic instrumentation installed in domestic NPPs will be discussed; this includes instrument type and location, the Operating Basis Earthquake (OBE) exceedance criteria, and processing and evaluation of earthquake response data, and items to be studied for further enhancement of post-earthquake evaluation techniques are presented

Upgrading instrumentation and control systems for plant safety and operation

International Nuclear Information System (INIS)

Martin, M.; Prehler, H.J.; Schramm, W.

1997-01-01

Upgrading the electrical systems and instrumentation and control systems has become increasingly more important in the past few years for nuclear power plants currently in operation. As the requirements to be met in terms of plant safety and availability have become more stringent in the past few years, Western plants built in the sixties and seventies have been the subject of manifold backfitting and upgrading measures in the past. In the meantime, however, various nuclear power plants are facing much more thorough upgrading phases because of the difficulties in obtaining spare parts for older equipment systems. As digital technology has become widespread in many areas because of its advantages, and as applications are continuously expanding, conventional equipment and systems are losing more and more ground as a consequence of decreasing demand. Merely because of the pronounced decline in demand for conventional electronic components it is possible for equipment manufacturers to guarantee spare parts deliveries for older systems only for specific future periods of time. In addition, one-off manufacture entails high costs in purchases of spare parts. As a consequence of current thinking more and more focusing on availability and economy, upgrading of electrical systems and instrumentation and control systems is becoming a more and more topical question, for older plants even to ensure completion of full service life. (orig.) [de

Advanced Test Reactor Safety Basis Upgrade Lessons Learned Relative to Design Basis Verification and Safety Basis Management

International Nuclear Information System (INIS)

G. L. Sharp; R. T. McCracken

2004-01-01

The Advanced Test Reactor (ATR) is a pressurized light-water reactor with a design thermal power of 250 MW. The principal function of the ATR is to provide a high neutron flux for testing reactor fuels and other materials. The reactor also provides other irradiation services such as radioisotope production. The ATR and its support facilities are located at the Test Reactor Area of the Idaho National Engineering and Environmental Laboratory (INEEL). An audit conducted by the Department of Energy's Office of Independent Oversight and Performance Assurance (DOE OA) raised concerns that design conditions at the ATR were not adequately analyzed in the safety analysis and that legacy design basis management practices had the potential to further impact safe operation of the facility.1 The concerns identified by the audit team, and issues raised during additional reviews performed by ATR safety analysts, were evaluated through the unreviewed safety question process resulting in shutdown of the ATR for more than three months while these concerns were resolved. Past management of the ATR safety basis, relative to facility design basis management and change control, led to concerns that discrepancies in the safety basis may have developed. Although not required by DOE orders or regulations, not performing design basis verification in conjunction with development of the 10 CFR 830 Subpart B upgraded safety basis allowed these potential weaknesses to be carried forward. Configuration management and a clear definition of the existing facility design basis have a direct relation to developing and maintaining a high quality safety basis which properly identifies and mitigates all hazards and postulated accident conditions. These relations and the impact of past safety basis management practices have been reviewed in order to identify lessons learned from the safety basis upgrade process and appropriate actions to resolve possible concerns with respect to the current ATR safety

Model of interaction in Smart Grid on the basis of multi-agent system

Science.gov (United States)

Engel, E. A.; Kovalev, I. V.; Engel, N. E.

2016-11-01

This paper presents model of interaction in Smart Grid on the basis of multi-agent system. The use of travelling waves in the multi-agent system describes the behavior of the Smart Grid from the local point, which is being the complement of the conventional approach. The simulation results show that the absorption of the wave in the distributed multi-agent systems is effectively simulated the interaction in Smart Grid.

Conventional resin cation exchangers versus EDI for CACE measurement in power plants. Feasibility and practical field results

Energy Technology Data Exchange (ETDEWEB)

Sigrist, Manuel [Swan Systeme AG, Hinwil (Switzerland)

2017-10-15

The conductivity measurement after a cation exchanger in power plants with steam turbines was introduced soon after 1950 by Larson and Lane. Due to the simple measuring principle, the sensitivity to ionic contaminations and to its high reliability, the conductivity measurement after a cation exchanger (CACE) has become the most commonly used online analytical method in power plants with steam generators. Swan has investigated electro deionisation (EDI) as substitution of the conventional cation exchange resin and has developed a new conductivity instrument using this principle. This paper provides a description of the conventional method for cation conductivity measurements as well as of the new AMI CACE using EDI method.

Conventional resin cation exchangers versus EDI for CACE measurement in power plants. Feasibility and practical field results

International Nuclear Information System (INIS)

Sigrist, Manuel

2017-01-01

The conductivity measurement after a cation exchanger in power plants with steam turbines was introduced soon after 1950 by Larson and Lane. Due to the simple measuring principle, the sensitivity to ionic contaminations and to its high reliability, the conductivity measurement after a cation exchanger (CACE) has become the most commonly used online analytical method in power plants with steam generators. Swan has investigated electro deionisation (EDI) as substitution of the conventional cation exchange resin and has developed a new conductivity instrument using this principle. This paper provides a description of the conventional method for cation conductivity measurements as well as of the new AMI CACE using EDI method.

International convention for the suppression of acts of nuclear terrorism

International Nuclear Information System (INIS)

Jankowitsch-Prevor, O.

2005-01-01

The Preamble, composed of 13 paragraphs and drafted in the usual style of a General Assembly resolution, is aimed at placing the convention in a number of relevant contexts. First, the convention is linked to the issue of the maintenance of international peace and security through a reference to the purposes of the United Nations under Article 1 of the Charter. Next, it is presented as being a further step in the decisions, measures and instruments developed by the United Nations over the past ten years with the common objective of eliminating international terrorism in all its forms. Lastly, the convention is placed in its specific nuclear context through a number of references. In its third paragraph, the Preamble contains a reference to the principle recognizing 'the right of all states to develop and apply nuclear energy for peaceful purposes and their legitimate interests in the potential benefits to be derived from the peaceful application of nuclear energy'. This paragraph is identical to the first paragraph of the Preamble of the CPPNM, and the same principle is stated again in the first paragraph of the Preamble of the Amendment to the CPPNM, and constitutes a kind of general statement in favour of the peaceful use of nuclear energy and technology, without explicit reservations concerning non-proliferation, the safety and security of nuclear facilities or the management of radioactive waste. A draft amendment presented by the United States delegation in the final phase of work that suggested adding the phrase 'while recognizing that the goals of peaceful utilisation should not be used as a cover for proliferation' to the sentence cited above, was apparently not retained. Next, the Preamble mentions the 1980 Convention on the Physical Protection of Nuclear Material, and in the tenth paragraph the threat that 'acts of nuclear terrorism may result in the gravest consequences and may pose a threat to international peace and security'. Paragraph 11 of the

Modern trends of electronic trading by negotiable financial instruments

OpenAIRE

Кравчук, Ігор Святославович

2018-01-01

International negotiable financial instrument markets have a high level of electronic trading. It is displayed using the consolidated limit order book, the widening the range of trading orders, smart order routing, high speed access to the market on the basis of latency minimizing. The result of electronic trading is the development of high-frequency trading, the positive features of which are the increase of trading activity and market liquidity, and the reducing of transaction costs. The ma...

Methodology and development of instruments for the safety analysis of a nuclear reprocessing plant

International Nuclear Information System (INIS)

Markett, J.

1987-01-01

Characteristics and overlapping aspects in the elaboration of safety analyses for the nuclear and conventional units are presented. The current methods are presented and their limits of applicability characterized. The transferability of individual methods or their elements to the analysis of the reference plant of Wackersdorf is examined and the procedure for the systems analysis is determined. It is of great importance to prove that the essential kinds of incidents and possibilities of release with potential effects in the environment are completely identified. The incidents are divided into basic incidents, which are characterized by superior physical/chemical release mechanisms. An essential objective is to systematize the safety analysis and to summarize the presentation of results. Selection criteria are presented, which allow a limitation of the analysis to essential influencing parameters without removing aspects from the overall safety-relevant statement. Besides the selection criteria, instruments and mathematical models are explained with the help of which the representative and possible incidents covering all potential risks for all areas of the plant, systems and components can be selected. These design-basis accidents (criticality, self-heating, fire, explosion, leakages, earth quakes) are decisive for the determination of potential damaging effects in the environment and thus for the overall statement on the licensability. (orig./HP) [de

Survey of instrumentation used for monitoring metals in water

Energy Technology Data Exchange (ETDEWEB)

Quinby-Hunt, M.S.

1978-06-01

A study was conducted of instrumentation used to determine metals in water. Several of the techniques most commonly used for analysis and routine determinations of metals in water are shown in Table 1. They are atomic absorption spectroscopy, both flame and flameless, atomic emission spectroscopy using conventional flame sources and inductively-coupled plasma sources, and ultraviolet-visible absorption techniques. Other less frequently employed methods are x-ray fluorescence analysis using both photon and charged particle excitation with energy-dispersive and wavelength-dispersive spectral analysis. Also electrochemical techniques and activation analysis are studied.

Youth Actuarial Risk Assessment Tool (Y-ARAT): The development of an actuarial risk assessment instrument for predicting general offense recidivism on the basis of police records.

Science.gov (United States)

van der Put, Claudia E

2014-06-01

Estimating the risk for recidivism is important for many areas of the criminal justice system. In the present study, the Youth Actuarial Risk Assessment Tool (Y-ARAT) was developed for juvenile offenders based solely on police records, with the aim to estimate the risk of general recidivism among large groups of juvenile offenders by police officers without clinical expertise. On the basis of the Y-ARAT, juvenile offenders are classified into five risk groups based on (combinations of) 10 variables including different types of incidents in which the juvenile was a suspect, total number of incidents in which the juvenile was a suspect, total number of other incidents, total number of incidents in which co-occupants at the youth's address were suspects, gender, and age at first incident. The Y-ARAT was developed on a sample of 2,501 juvenile offenders and validated on another sample of 2,499 juvenile offenders, showing moderate predictive accuracy (area under the receiver-operating-characteristic curve = .73), with little variation between the construction and validation sample. The predictive accuracy of the Y-ARAT was considered sufficient to justify its use as a screening instrument for the police. © The Author(s) 2013.

Reliability of conventional shade guides in teeth color determination.

Science.gov (United States)

Todorović, Ana; Todorović, Aleksandar; Gostović, Aleksandra Spadijer; Lazić, Vojkan; Milicić, Biljana; Djurisić, Slobodan

2013-10-01

Color matching in prosthodontic therapy is a very important task because it influences the esthetic value of dental restorations. Visual shade matching represents the most frequently applied method in clinical practice. Instrumental measurements provide objective and quantified data in color assessment of natural teeth and restorations. In instrumental shade analysis, the goal is to achieve the smallest deltaE value possible, indicating the most accurate shade match. The aim of this study was to evaluate the reliability of commercially available ceramic shade guides. VITA Easyshade spectrophotometer (VITA, Germany) was used for instrumental color determination. Utilizing this device, color samples of ten VITA Classical and ten VITA 3D - Master shade guides were analyzed. Each color sample from all shade guides was measured three times and the basic parameters of color quality were examined: deltaL, deltaC, deltaH, deltaE, deltaElc. Based on these parameters spectrophotometer marks the shade matching as good, fair or adjust. After performing 1,248 measurements of ceramic color samples, frequency of evaluations adjust, fair and good were statistically significantly different between VITA Classical and VITA 3D Master shade guides (p = 0.002). There were 27.1% cases scored as adjust, 66.3% as fair and 6.7% as good. In VITA 3D - Master shade guides 30.9% cases were evaluated as adjust, 66.4% as fair and 2.7% cases as good. Color samples from different shade guides, produced by the same manufacturer, show variability in basic color parameters, which once again proves the lack of precision and nonuniformity of the conventional method.

Declining conventional cancer treatment and using complementary and alternative medicine: a problem or a challenge?

Science.gov (United States)

Verhoef, M J; Rose, M S; White, M; Balneaves, L G

2008-08-01

Several studies have shown that a small but significant percentage of cancer patients decline one or more conventional cancer treatments and use complementary and alternative medicine (CAM) instead. Here, drawing on the literature and on our own ongoing research, we describe why cancer patients decide to decline conventional cancer treatments, who those patients are, and the response by physicians to patients who make such decisions. Poor doctor-patient communication, the emotional impact of the cancer diagnosis, perceived severity of conventional treatment side effects, a high need for decision-making control, and strong beliefs in holistic healing appear to affect the decision by patients to decline some or all conventional cancer treatments. Many patients indicate that they value ongoing follow-up care from their oncologists provided that the oncologists respect their beliefs. Patients declining conventional treatments have a strong sense of internal control and prefer to make the final treatment decisions after considering the opinions of their doctors. Few studies have looked at the response by physicians to patients making such a decision. Where research has been done, it found that a tendency by doctors to dichotomize patient decisions as rational or irrational may interfere with the ability of the doctors to respond with sensitivity and understanding. Declining conventional treatment is not necessarily an indicator of distrust of the medical system, but rather a reflection of many personal factors. Accepting and respecting such decisions may be instrumental in "keeping the door open."

Instrumental basis utilizing a sodium iodide detector for radioactive soil evaluations for site remediation

International Nuclear Information System (INIS)

Davis, A.I.

1996-07-01

This document provides the design rational for using a 5.08 by 5.08 cm (2 by 2 in.) sodium iodide detector to aid in boundary mapping of the radioactive contaminated soils at the Hanford Site. The detector can provide adequate response to a homogeneously contaminated soil volume of at least 1.22 to 1.52 m in diameter and up to 45.7 cm deep. The gamma activity basis is described by a soil column in a right circular cylinder that is uniformly isotopic. The detection techniques and characteristics are used to define contaminated areas requiring excavation by locating regions where gamma activities exceed cleanup standards. To determine the areas and boundary of contamination, the boundary and adjacent surfaces will be mapped using the detector operated in a windowed gross-gamma mode

Comparing near-infrared conventional diffuse reflectance spectroscopy and hyperspectral imaging for determination of the bulk properties of solid samples by multivariate regression: determination of Mooney viscosity and plasticity indices of natural rubber.

Science.gov (United States)

Juliano da Silva, Carlos; Pasquini, Celio

2015-01-21

Conventional reflectance spectroscopy (NIRS) and hyperspectral imaging (HI) in the near-infrared region (1000-2500 nm) are evaluated and compared, using, as the case study, the determination of relevant properties related to the quality of natural rubber. Mooney viscosity (MV) and plasticity indices (PI) (PI0 - original plasticity, PI30 - plasticity after accelerated aging, and PRI - the plasticity retention index after accelerated aging) of rubber were determined using multivariate regression models. Two hundred and eighty six samples of rubber were measured using conventional and hyperspectral near-infrared imaging reflectance instruments in the range of 1000-2500 nm. The sample set was split into regression (n = 191) and external validation (n = 95) sub-sets. Three instruments were employed for data acquisition: a line scanning hyperspectral camera and two conventional FT-NIR spectrometers. Sample heterogeneity was evaluated using hyperspectral images obtained with a resolution of 150 × 150 μm and principal component analysis. The probed sample area (5 cm(2); 24,000 pixels) to achieve representativeness was found to be equivalent to the average of 6 spectra for a 1 cm diameter probing circular window of one FT-NIR instrument. The other spectrophotometer can probe the whole sample in only one measurement. The results show that the rubber properties can be determined with very similar accuracy and precision by Partial Least Square (PLS) regression models regardless of whether HI-NIR or conventional FT-NIR produce the spectral datasets. The best Root Mean Square Errors of Prediction (RMSEPs) of external validation for MV, PI0, PI30, and PRI were 4.3, 1.8, 3.4, and 5.3%, respectively. Though the quantitative results provided by the three instruments can be considered equivalent, the hyperspectral imaging instrument presents a number of advantages, being about 6 times faster than conventional bulk spectrometers, producing robust spectral data by ensuring sample

Socio-economic characteristics and the effect of taxation as a health policy instrument

DEFF Research Database (Denmark)

Smed, Sinne; Jensen, Jørgen Dejgård; Denver, Sigrid

2007-01-01

This paper analyses the quantitative effects of using economic instruments in health policy on the basis of price elasticities calculated from estimated demand systems. The nutritional effects of various taxation schemes are compared for households in different age groups and social classes...... of the instruments and the targeting of vulnerable groups with special needs should be done with care. It should be noted that a tax on a single nutrient or food may have undesired effects on the demand for other food components, though this may be avoided by introducing taxes/subsidies on several food products...

Instrumentation of a prestressed concrete containment vessel model

International Nuclear Information System (INIS)

Hessheimer, M.F.; Rightley, M.J.; Matsumoto, T.

1995-01-01

A series of static overpressurization tests of scale models of nuclear containment structures is being conducted by Sandia National Laboratories for the Nuclear Power Engineering Corporation of Japan and the U.S. Nuclear Regulatory Commission. At present, two tests are being planned: a test of a model of a steel containment vessel (SCV) that is representative of an improved, boiling water reactor (BWR) Mark II design; and a test of a model of a prestressed concrete containment vessel (PCCV). This paper discusses plans and the results of a preliminary investigation of the instrumentation of the PCCV model. The instrumentation suite for this model will consist of approximately 2000 channels of data to record displacements, strains in the reinforcing steel, prestressing tendons, concrete, steel liner and liner anchors, as well as pressure and temperature. The instrumentation is being designed to monitor the response of the model during prestressing operations, during Structural Integrity and Integrated Leak Rate testing, and during test to failure of the model. Particular emphasis has been placed on instrumentation of the prestressing system in order to understand the behavior of the prestressing strands at design and beyond design pressure levels. Current plans are to place load cells at both ends of one third of the tendons in addition to placing strain measurement devices along the length of selected tendons. Strain measurements will be made using conventional bonded foil resistance gages and a wire resistance gage, known as a open-quotes Tensmegclose quotes reg-sign gage, specifically designed for use with seven-wire strand. The results of preliminary tests of both types of gages, in the laboratory and in a simulated model configuration, are reported and plans for instrumentation of the model are discussed

Chemical Weapons Convention

National Research Council Canada - National Science Library

1997-01-01

On April 29, 1997, the Convention on the Prohibition of the Development, Production, Stockpiling, and Use of Chemical Weapons and on Their Destruction, known as the Chemical Weapons Convention (CWC...

Development, use and maintenance of the design basis threat. Implementing guide

International Nuclear Information System (INIS)

2009-01-01

threat to those assets. As described in this publication, an understanding of the threat can lead to a detailed description of potential adversaries (the design basis threat), which, in turn, is the basis of an appropriately designed physical protection system. This direct link gives confidence that protection would be effective against an adversary attack. International experience in using a design basis threat to protect assets of high consequence is largely based on the protection of nuclear material and facilities. Furthermore, the nuclear security documents defining and recommending that physical protection be based upon the threat - The Physical Protection Objectives and Fundamental Principles (GOV/2001/41/ Attachment), the Recommendations on the Physical Protection of Nuclear Facilities and Nuclear Material (INFCIRC/225/Rev. 4 (corrected)), and the Convention on Physical Protection of Nuclear Facilities and Nuclear Material as Amended (INFCIRC/274) (adopted on 8 July 2005; (GOV/2005/57)) - do so exclusively for the protection of nuclear material and facilities. Given the historical background, and its continuing contemporary relevance, it has been necessary to draw on that nuclear protection experience in developing this publication. However, the general approach can also be applied to protecting other assets that require a high degree of confidence in the effectiveness of their protection, such as high-activity radioactive material. Specialists from France, Germany, Japan, the Russian Federation, Spain, the United Kingdom, and the United States of America assisted the IAEA in preparing this publication. A draft was presented to an open-ended technical meeting in December 2006, and subsequently circulated for comment to all Member States. This publication is consistent with The Physical Protection Objectives and Fundamental Principles; the Convention on Physical Protection of Nuclear Facilities and Nuclear Material as Amended; and the Recommendations on the

Paris Convention on third party liability in the field of nuclear energy and Brussels Convention Supplementary to the Paris Convention

International Nuclear Information System (INIS)

1989-01-01

This new bilingual (English and French) edition of the 1960 Paris Convention and 1963 Brussels Supplementary Convention incorporates the provisions of the Protocols which amended each of them on two occasions, in 1964 and 1982. The Expose des motifs to the Paris Convention, as revised in 1982 is also included in this pubication. (NEA) [fr

Innovative market-based policy instruments for waste management: A case study on shredder residues in Belgium.

Science.gov (United States)

Dubois, Maarten; Hoogmartens, Rob; Van Passel, Steven; Van Acker, Karel; Vanderreydt, Ive

2015-10-01

In an increasingly complex waste market, market-based policy instruments, such as disposal taxes, can give incentives for sustainable progress while leaving flexibility for innovation. However, implementation of disposal taxes is often criticised by domestic waste handlers that fear to be outcompeted by competitors in other countries. The article discusses three innovative market-based instruments that limit the impact on international competitiveness: Tradable recycling credits, refunded disposal taxes and differentiated disposal taxes. All three instruments have already been implemented for distinct environmental policies in Europe. In order to illustrate how these instruments can be used for waste policy, the literature review is complemented with a case study on shredder residues from metal-containing waste streams in Belgium. The analysis shows that a conventional disposal tax remains the most efficient, simple and transparent instrument. However, if international competition is a significant issue or if political support is weak, refunded and differentiated disposal taxes can have an added value as second-best instruments. Tradable recycling credits are not an appropriate instrument for use in small waste markets with market power. In addition, refunded taxes create similar incentives, but induce lower transactions costs. © The Author(s) 2015.

Separation of musical instruments based on amplitude and frequency comodulation

Science.gov (United States)

Jacobson, Barry D.; Cauwenberghs, Gert; Quatieri, Thomas F.

2002-05-01

In previous work, amplitude comodulation was investigated as a basis for monaural source separation. Amplitude comodulation refers to similarities in amplitude envelopes of individual spectral components emitted by particular types of sources. In many types of musical instruments, amplitudes of all resonant modes rise/fall, and start/stop together during the course of normal playing. We found that under certain well-defined conditions, a mixture of constant frequency, amplitude comodulated sources can unambiguously be decomposed into its constituents on the basis of these similarities. In this work, system performance was improved by relaxing the constant frequency requirement. String instruments, for example, which are normally played with vibrato, are both amplitude and frequency comodulated sources, and could not be properly tracked under the constant frequency assumption upon which our original algorithm was based. Frequency comodulation refers to similarities in frequency variations of individual harmonics emitted by these types of sources. The analytical difficulty is in defining a representation of the source which properly tracks frequency varying components. A simple, fixed filter bank can only track an individual spectral component for the duration in which it is within the passband of one of the filters. Alternatives are therefore explored which are amenable to real-time implementation.

Operation Iraqi Freedom: DOD Should Apply Lessons Learned Concerning the Need for Security over Conventional Munitions Storage Sites to Future Operations Planning

National Research Council Canada - National Science Library

D'Agostino, Davi M

2007-01-01

The Government Accountability Office (GAO) is releasing a report today on lessons learned concerning the need for security over conventional munitions storage sites that provides the basis for this testimony...

Role of Islamic Banking and Conventional Against Poverty with The Dual Banking System

Directory of Open Access Journals (Sweden)

Iwan Setiawan

2016-12-01

Full Text Available Islamic banking in Indonesia is present in a dual banking system. Islamic banking is expected to contribute more in the process of economic development and improving people’s welfare. The  main  objective of  this  study is  to  analyze the  role  of  financing Islamic banking and conventional banking credit to the improvement of people’s welfare as measured by reductions in poverty. The study was conducted using  the explanatory method, applying the  panel  regression estimation techniques simultaneously with the  Two Stage Least Square  method (TSLS  using  data from the period 1992-2012. Results  of the study reveals that the increased of  financing Islamic banking and conventional banking credit assign roles  to poverty reduction in Indonesia. The role of Islamic banking financing is lower  than conventional bank  credit role  in reducing poverty. In addition to improve financing and credit, changes should be applied in the value  of the instruments of monetary policy, economic growth, unequal distribution  of income and  the depreciation  of the local  currency that contribute towards poverty conditions.

Removal of artificial dental calculus by use of conventional and diamond ultrasound tips.

Directory of Open Access Journals (Sweden)

Roberto Carlos Mourão Pinho

2017-04-01

Full Text Available Introduction: Periodontal disease is considered a public health problem and may lead to serious complications as the general health of patient. The main therapeutic procedure is scaling and root planing, which can be performed by a variety of techniques and instruments Objective:The aim of the present study was to evaluate the removal of calculus, produced artificially, by using a conventional ultrasonic tip and a diamond – CVD tip. Method: The calculus was produced with artificial sawdust and glue-based cyanoacrylate and distributed in twenty areas also standardized on two plates of acrylic resin (chemical activated, holding 10 samples per plate. Standards / samples were divided by lot into two simple groups, being A (treated with conventional tip and B (treated with CVD tip. Results:The treatment in Group A, promoted an average area of 20.48 ± 4.20 mm2 free of artificial calculus which is significantly higher (p <0.05 than the area removed in Group B (15.37 ± 5.29 mm2. Conclusion:The results showed that the conventional tip presented higher results than CVD tip for efficacy in the removal of calculus.

Climate change convention

International Nuclear Information System (INIS)

Russell, D.

1992-01-01

Principles that guide Canada's Green Plan with respect to global warming are outlined. These include respect for nature, meeting environmental goals in an economically beneficial manner, efficient use of resources, shared responsibilities, federal leadership, and informed decision making. The policy side of the international Framework Convention on Climate Change is then discussed and related to the Green Plan. The Convention has been signed by 154 nations and has the long-term objective of stabilizing anthropogenic greenhouse gas concentrations in the atmosphere at levels that prevent dangerous interference with the climate system. Some of the Convention's commitments toward achieving that objective are only applicable to the developed countries. Five general areas of commitment are emissions reductions, assistance to developing countries, reporting requirements, scientific and socioeconomic research, and education. The most controversial area is that of limiting emissions. The Convention has strong measures for public accountability and is open to future revisions. Canada's Green Plan represents one country's response to the Convention commitments, including a national goal to stabilize greenhouse gas emissions at the 1990 level by the year 2000

Comparative study of the performance of conventional and column flotation when treating coking coal fines

Energy Technology Data Exchange (ETDEWEB)

Jena, M.S.; Biswal, S.K.; Das, S.P.; Reddy, P.S.R. [Institute of Minerals and Materials Technology (CSIR), Bhubaneswar - 751 013 (India)

2008-12-15

Investigations were carried out on coking coal fines by conventional cell and column flotation techniques. The effects of different operating parameters were evaluated for both conventional and column flotation. The coal fines were collected from Bhojudih washery, India. These coal fines averaged 24.4% ash, 19.8% volatile matter and 53.8% fixed carbon on a dry basis. A commercial grade sodium silicate, light diesel oil and pine oil were used as depressant, collector and frother respectively. The flotation performance was compared with release analysis. The conventional flotation results indicated that a clean coal with 14.4% ash could be obtained at 78.0% yield with 88.4% combustible recovery. The ash of the clean coal could be further reduced to 10.1% at 72.0% yield with 85.6% combustible recovery by using column flotation. The column flotation results were close to those obtained by release analysis. (author)

Comparison of the cyclic fatigue resistance of 5 different rotary pathfinding instruments made of conventional nickel-titanium wire, M-wire, and controlled memory wire.

Science.gov (United States)

Capar, Ismail Davut; Kaval, Mehmet Emin; Ertas, Hüseyin; Sen, Bilge Hakan

2015-04-01

This study compared the cyclic fatigue resistance of current nickel-titanium rotary path-finding instruments. Five types of nickel-titanium rotary pathfinding instruments were used in steel canals with a 90° curvature and a curvature radius of 3 mm (n = 10) and 5 mm (n = 10). The cyclic fatigue of the following instruments was tested at 4 mm from the tip: PathFile (#16 and a .02 taper; Dentsply Maillefer, Ballaigues, Switzerland), G-File (#12 and a .03 taper; Micro-Mega, Besançon Cedex, France), Scout Race (#15 and a .02 taper; FKG Dentaire, La Chaux-de-Fonds, Switzerland), HyFlex GPF (#15 and a .02 taper; Coltene-Whaledent, Allstetten, Switzerland), and ProGlider (#16 with a mean taper of .04125 and a .02 at the first 4 mm from the tip, Dentsply Maillefer). The length of the fractured parts was measured, and the number of cycles to fracture (NCF) was calculated. The data were statistically analyzed using Kruskal-Wallis and Mann-Whitney tests (α = .05). After Bonferroni correction, the new P value was set as .005. The difference in the cyclic fatigue of all the files at both curvatures was statistically significant (P values from .0035 to less than .0001). The ranking of the instruments from the highest to the lowest NCF was as follows: HyFlex GPF, G files, ProGlider, PathFile, and Scout Race. The length of the fractured part of the instruments was similar in all the groups (P > .05). All the tested instruments had a lower NCF at a curvature radius of 3 mm when compared with a curvature radius of 5 mm (P instrument was the highest, and the curvature radius had a significant effect on the fatigue resistance. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Instrument Remote Control via the Astronomical Instrument Markup Language

Science.gov (United States)

Sall, Ken; Ames, Troy; Warsaw, Craig; Koons, Lisa; Shafer, Richard

1998-01-01

The Instrument Remote Control (IRC) project ongoing at NASA's Goddard Space Flight Center's (GSFC) Information Systems Center (ISC) supports NASA's mission by defining an adaptive intranet-based framework that provides robust interactive and distributed control and monitoring of remote instruments. An astronomical IRC architecture that combines the platform-independent processing capabilities of Java with the power of Extensible Markup Language (XML) to express hierarchical data in an equally platform-independent, as well as human readable manner, has been developed. This architecture is implemented using a variety of XML support tools and Application Programming Interfaces (API) written in Java. IRC will enable trusted astronomers from around the world to easily access infrared instruments (e.g., telescopes, cameras, and spectrometers) located in remote, inhospitable environments, such as the South Pole, a high Chilean mountaintop, or an airborne observatory aboard a Boeing 747. Using IRC's frameworks, an astronomer or other scientist can easily define the type of onboard instrument, control the instrument remotely, and return monitoring data all through the intranet. The Astronomical Instrument Markup Language (AIML) is the first implementation of the more general Instrument Markup Language (IML). The key aspects of our approach to instrument description and control applies to many domains, from medical instruments to machine assembly lines. The concepts behind AIML apply equally well to the description and control of instruments in general. IRC enables us to apply our techniques to several instruments, preferably from different observatories.

Structural analysis of HyFlex EDM instruments.

Science.gov (United States)

Iacono, F; Pirani, C; Generali, L; Bolelli, G; Sassatelli, P; Lusvarghi, L; Gandolfi, M G; Giorgini, L; Prati, C

2017-03-01

To compare the phase transformation behaviour, the microstructure, the nano-hardness and the surface chemistry of electro-discharge machined HyFlex EDM instruments with conventionally manufactured HyFlex CM. New and laboratory used HyFlex EDM were examined by X-ray diffraction (XRD) and differential scanning calorimetry (DSC). Nano-hardness and modulus of elasticity were also investigated using a maximum load of 20 mN with a minimum of 40 significant indentations for each sample. Raman spectroscopy and field emission-scanning electron microscope (FE-SEM) were used to assess the surface chemistry of HyFlex EDM. HyFlex CM were subjected to the same investigations and used as a comparison. Nano-indentation data were statistically analysed using the Student's t-test. XRD analysis on HyFlex EDM revealed the presence of martensite and rhombohedral R-phase, while a mixture of martensite and austenite structure was identified in HyFlex CM. DSC analysis also disclosed higher austenite finish (Af) temperatures for electro-discharge machining (EDM) instruments. Significant differences in nano-hardness and modulus of elasticity were found between EDM and CM files (P EDM and CM files were covered by an oxide layer. Micro-Raman spectroscopy assessed the presence of rutile-TiO 2 . HyFlex EDM revealed peculiar structural properties, such as increased phase transformation temperatures and hardness. Present results corroborated previous findings and shed light on the enhanced mechanical behaviour of these instruments. © 2016 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Ultrafast electron microscopy: Instrument response from the single-electron to high bunch-charge regimes

Science.gov (United States)

Plemmons, Dayne A.; Flannigan, David J.

2017-09-01

We determine the instrument response of an ultrafast electron microscope equipped with a conventional thermionic electron gun and absent modifications beyond the optical ports. Using flat, graphite-encircled LaB6 cathodes, we image space-charge effects as a function of photoelectron-packet population and find that an applied Wehnelt bias has a negligible effect on the threshold levels (>103 electrons per pulse) but does appear to suppress blurring at the upper limits (∼105 electrons). Using plasma lensing, we determine the instrument-response time for 700-fs laser pulses and find that single-electron packets are laser limited (1 ps), while broadening occurs well below the space-charge limit.

Design and Validation of an Instrumented Uneven Terrain Treadmill.

Science.gov (United States)

Voloshina, Alexandra S; Ferris, Daniel P

2018-06-01

Studying human and animal locomotion on an uneven terrain can be beneficial to basic science and applied studies for clinical and robotic applications. Traditional biomechanical analysis of human locomotion has often been limited to laboratory environments with flat, smooth runways and treadmills. The authors modified a regular exercise treadmill by attaching wooden blocks to the treadmill belt to yield an uneven locomotion surface. To ensure that these treadmill modifications facilitated biomechanical measurements, the authors compared ground reaction force data collected while a subject ran on the modified instrumented treadmill with a smooth surface with data collected using a conventional instrumented treadmill. Comparisons showed only minor differences. These results suggest that adding an uneven surface to a modified treadmill is a viable option for studying human or animal locomotion on an uneven terrain. Other types of surfaces (eg, compliant blocks) could be affixed in a similar manner for studies on other types of locomotion surfaces.

High precision flux measurements in conventional neutrino beams: the ENUBET project

CERN Document Server

Longhin, Andrea

2017-01-01

The challenges of precision neutrino physics require measurements of absolute neutrino cross sec- tions at the GeV scale with exquisite (1%) precision. This precision is presently limited to by the uncertainties on neutrino flux at the source. A reduction of this uncertainty by one order of mag- nitude can be achieved monitoring the positron production in the decay tunnel originating from the K e 3 decays of charged kaons in a sign and momentum selected narrow band beam. This novel technique enables the measurement of the most relevant cross-sections for CP violation ( ν e and ̄ ν e ) with a precision of 1% and requires a special instrumented beam-line. Such non-conventional beam-line will be developed in the framework of the ENUBET Horizon-2020 Consolidator Grant, recently approved by the European Research Council. We present the Project, the first experimen- tal results on ultra-compact calorimeters that can embedded in the instrumented decay tunnel and the advances on the simulation of the beamline. A r...

Growth of InAs Wurtzite Nanocrosses from Hexagonal and Cubic Basis

DEFF Research Database (Denmark)

Krizek, Filip; Kanne, Thomas; Razmadze, Davydas

2017-01-01

. Two methods use conventional wurtzite nanowire arrays as a 6-fold hexagonal basis for growing single crystal wurtzite nanocrosses. A third method uses the 2-fold cubic symmetry of (100) substrates to form well-defined coherent inclusions of zinc blende in the center of the nanocrosses. We show......Epitaxially connected nanowires allow for the design of electron transport experiments and applications beyond the standard two terminal device geometries. In this Letter, we present growth methods of three distinct types of wurtzite structured InAs nanocrosses via the vapor-liquid-solid mechanism...

Advanced Instrumentation for Transient Reactor Testing

Energy Technology Data Exchange (ETDEWEB)

Corradini, Michael L.; Anderson, Mark; Imel, George; Blue, Tom; Roberts, Jeremy; Davis, Kurt

2018-01-31

Transient testing involves placing fuel or material into the core of specialized materials test reactors that are capable of simulating a range of design basis accidents, including reactivity insertion accidents, that require the reactor produce short bursts of intense highpower neutron flux and gamma radiation. Testing fuel behavior in a prototypic neutron environment under high-power, accident-simulation conditions is a key step in licensing nuclear fuels for use in existing and future nuclear power plants. Transient testing of nuclear fuels is needed to develop and prove the safety basis for advanced reactors and fuels. In addition, modern fuel development and design increasingly relies on modeling and simulation efforts that must be informed and validated using specially designed material performance separate effects studies. These studies will require experimental facilities that are able to support variable scale, highly instrumented tests providing data that have appropriate spatial and temporal resolution. Finally, there are efforts now underway to develop advanced light water reactor (LWR) fuels with enhanced performance and accident tolerance. These advanced reactor designs will also require new fuel types. These new fuels need to be tested in a controlled environment in order to learn how they respond to accident conditions. For these applications, transient reactor testing is needed to help design fuels with improved performance. In order to maximize the value of transient testing, there is a need for in-situ transient realtime imaging technology (e.g., the neutron detection and imaging system like the hodoscope) to see fuel motion during rapid transient excursions with a higher degree of spatial and temporal resolution and accuracy. There also exists a need for new small, compact local sensors and instrumentation that are capable of collecting data during transients (e.g., local displacements, temperatures, thermal conductivity, neutron flux, etc.).

The Hague Judgments Convention

DEFF Research Database (Denmark)

Nielsen, Peter Arnt

2011-01-01

The Hague Judgments Convention of 2005 is the first global convention on international jurisdiction and recognition and enforcement of judgments in civil and commercial matters. The author explains the political and legal background of the Convention, its content and certain crucial issues during...

Concepts of nuclear liability revisited: a post-Chernobyl assessment of the Paris and the Vienna Conventions

International Nuclear Information System (INIS)

Pelzer, Norbert

1988-01-01

The accident at Chernobyl caused evident damage to third parties. Nuclear third party liability law was applicable. It is thus timely to reassess the concept of the international civil nuclear liability regulations, with special reference to the accident and the proceedings which resulted from it. The first section deals with the basis of liability - the origin and development of the Paris and Vienna Conventions, various aspects of liability and international implementation of the Convention. The second part considers the limitations on the liability and the third part looks at recent developments and future prospects which include the draft of a joint protocol. (U.K.)

Aseismatic design of electrical equipments and instruments for nuclear power stations

International Nuclear Information System (INIS)

Suzuki, Yasuharu; Nishizawa, Kazuo; Miyazaki, Yoshio; Miura, Takumi

1977-01-01

The aseismatic design of electrical instruments is carried out according to IEEE Standard 344-1971 in the USA. In Japan also, the method of aseismatic design of electrical instruments has been investigated by the representatives of electric power companies and electric machine makers since 1972. In Hitachi Ltd., the statical method of confirming aseismatic property was established on the basis of the rigid design for electrical instruments. It is convenient to examine the aseismatic property of electrical equipments by classifying them into control and switch boards, electrical appliances, equipments and circuits. It is possible to use the static method treating earthquake force as static load by avoiding resonance with the electrical equipments which have the higher natural frequency than that of buildings. The purposes of the vibration test are to prove the validity of the theoretical analysis, to clarify the vibration characteristics, and to confirm the maintenance of functions and the strength of the equipments. The vibration tests of control boards, the switch boards of enclosed type, motor control centers, the racks for instrumentation, storage batteries and electrical appliances are explained. Moreover, the vibration analysis with a computer according to finite element method is described. (Kako, I.)

Preliminary Validation of a New Instrument to Measure Life Satisfaction in Adolescents with Neuromuscular Disorders.

Science.gov (United States)

Reid, Denise T.; Renwick, Rebecca M.

1994-01-01

A new questionnaire instrument, the Life Satisfaction Index for Adolescents (LSIA), has been developed for adolescents with Duchenne muscular dystrophy (DMD). This article reviews the conceptual basis of the LSIA, its development, and its reliability and validity (established with 15 male adolescents with DMD). (DB)

The Aarhus Convention: A new regional convention on citizens' environmental rights

International Nuclear Information System (INIS)

Wates, J.

2000-01-01

The UN ECE Convention on Access to Information, Public Participation in Decision-making and Access to Justice in Environmental Matters had been adopted at Arhus, Denmark, at the Fourth Ministerial Conference in the 'Environment for Europe' process, and signed by thirty-five countries and the European Community. This paper summarises the main features of the Convention and briefly discusses its relevance to radioactive waste management issues. It then describes some of the activities currently being undertaken under the auspices of the Convention. (author)

Root canal preparation in endodontics: conventional versus laser methods

Science.gov (United States)

Goodis, Harold E.; White, Joel M.; Marshall, Sally J.; Marshall, Grayson W.; Moskowitz, Emrey

1992-06-01

Conventional cleaning and shaping of root canal systems employs hand and/or rotary instrumentation to remove the contents of the canal and shape the canal to receive a filling material. With the advent of the Nd:YAG laser system another method of accomplishing proper cleaning and shaping is evaluated. Single rooted teeth were radiographed bucco- lingually and mesio-distally and were divided into 2 groups. The first group was accessed and the root canal systems cleaned and shaped with a step back technique utilizing hand files and gates glidden burs. At completion of the procedure the teeth were again radiographed at the same positions as those prior to the procedure. The teeth were split longitudinally and examined under scanning electron microscopy to assess cleaning. The second group of teeth were accessed, and cleaning and shaping was accomplished using the Nd:YAG laser in combination with hand files and rotary instruments. These teeth were subjected to the same analysis as those in the first group. The before and after radiographs of each group were subjected to image analysis to determine effectiveness of the two methods in shaping the canal systems. We will discuss the ability of Nd:YAG to clean and shape root canal spaces and remove smear layer and organic tissue remnants from those areas.

A GC Instrument Simulator

Science.gov (United States)

Armitage, D. Bruce

1999-02-01

This simulator was developed to help students beginning the study of gas chromatographic instruments to understand their operation. It is not meant to teach chromatographic theory. The instrument simulator is divided into 5 sections. One is for sample preparation. Another is used to manage carrier gases and choose a detector and column. The third sets the conditions for either isothermal or programmed temperature operation. A fourth section models manual injections, and the fifth is the autosampler. The operator has a choice among 6 columns of differing diameters and packing polarities and a choice of either isothermal or simple one-stage temperature programming. The simulator can be operated in either single-sample mode or as a 10-sample autosampler. The integrator has two modes of operation, a "dumb" mode in which only the retention time, area of the peak, and percentage area are listed and a "smart" mode that also lists the components' identities. The identities are obtained from a list of names and retention times created by the operator. Without this list only the percentages and areas are listed. The percentages are based on the areas obtained from the chromatogram and not on the actual percentages assigned during sample preparation. The data files for the compounds used in the simulator are ASCII files and can be edited easily to add more compounds than the 11 included with the simulator. A maximum of 10 components can be used in any one sample. Sample mixtures can be made on a percent-by-volume basis, but not by mass of sample per volume of solvent. A maximum of 30 compounds can be present in any one file, but the number of files is limited only by the operating system. (I suggest that not more than 20 compounds be used in any one file, as scrolling through large numbers of compounds is annoying to say the least.) File construction and layout are discussed in detail in the User's Manual. Chromatograms are generated by calculating a retention time based on

Instrument electronic transformers for medium voltage systems; Transformadores eletronicos de instrumentos para sistemas de media tensao

Energy Technology Data Exchange (ETDEWEB)

Javora, Radek; Stefanka, Martin; Mahonen, Pentti; Niemi, Tapio; Rintamaki, Olli [ABB, Helsinki (Finland); ABB, Prague (Czech Republic)

2010-02-15

This paper compares the conventional technologies and the electronic of instrument transformers, and highlights the advantages, discoveries and principles of electronic models. Such equipment are essentially indicated for using with as micro processed relays at the substations, and also projected for connection to the IEDs, and the future digital communication (author)

Research within the coordinated programme on investigation of maintenance of nuclear instrumentation in developing countries. Latin America

International Nuclear Information System (INIS)

Guzman-Acevedo, C.

1980-06-01

The situation in Peru with regard to the maintenance and repair of instruments used in nuclear medicine is presented. On the basis of responses to questionnaires it appears that 56 instruments for nuclear medicine are in use in the country, almost exclusively in the capital Lima. The average age of the instruments is 9.5 years. They are in use about 16.4% of the possible time. The development of nuclear medicine in Peru is in its initial stages and difficulties encountered arise both from the lack of training and experience in nuclear medicine on the part of the medical personnel as well as lack of experience of the technicians responsible for instrument maintenance. Practically no preventive maintenance ever takes place; action is only taken when an instrument breaks down. Various suggestions are made in order to attempt an improvement of the situation

Out-of-core instrumentation system for the detection of flux disturbances in pebble-bed HTR reactors

International Nuclear Information System (INIS)

Neef, R.D.; Al-Dabagh, D.; Carlson, D.E.; Knob, P.; Schaal, H.

1981-01-01

Investigations have shown that central (radial) disturbances inside the core can be identified from the correlated measuring signals of the upper and bottom reflectors. Excentric (azimuthal) disturbances are easily recognized in the horizontal (r-PHI) plane; it should be possible to establish also their three-dimensional extent on the basis of all three instrumentation systems. Combined measurements with all three systems of instrumentation yield sufficient information for the initiation and monitoring of control processes in case of disturbances. (orig.) [de

Efforts onto electricity and instrumentation technology for nuclear power generation

International Nuclear Information System (INIS)

Hayakawa, Toshifumi

2000-01-01

Nuclear power generation shares more than 1/3 of all amounts of in-land generation at present, as a supplying source of stable electric energy after 2000 either. As a recent example of efforts onto electricity and instrumentation technology for nuclear power generation, there are, on instrumentation control system a new central control board aiming at reduction of operator's load, protection of human error, and upgrading of system reliability and economics by applying high level micro-processor applied technique and high speed data transfer technique to central monitoring operation and plant control protection, on a field of reactor instrumentation a new digital control rod position indicator improved of conventional system on a base of operation experience and recent technology, on a field of radiation instrumentation a new radiation instrumentation system accumulating actual results in a wide application field on a concept of application to nuclear power plant by adopting in-situ separation processing system using local network technique, and on a field of operation maintenance and management a conservation management system for nuclear generation plant intending of further effectiveness of operation maintenance management of power plant by applying of operation experience and recent data processing and communication technology. And, in the large electric apparatus, there are some generators carried out production and verification of a model one with actual size in lengthwise dimension, to correspond to future large capacity nuclear power plant. By this verification, it was proved that even large capacity generator of 1800 MVA class could be manufactured. (G.K.)

Process instrument monitoring for SNM solution surveillance

International Nuclear Information System (INIS)

Armatys, C.M.; Johnson, C.E.; Wagner, E.P.

1983-02-01

A process monitoring computer system at the Idaho Chemical Processing Plant (ICPP) is being used to evaluate nuclear fuel reprocessing plant data for Safeguards surveillance capabilities. The computer system was installed to collect data from the existing plant instruments and to evaluate what safeguards assurances can be provided to complement conventional accountability and physical protection measures. Movements of solutions containing special nuclear material (SNM) can be observed, activities associated with accountancy measurements (mixing, sampling, and bulk measurement) can be confirmed, and long-term storage of SNM solutions can be monitored to ensure containment. Special precautions must be taken, both in system design and operation to ensure adequate coverage of essential measured parameters and interpretation of process data, which can be comprised by instrument malfunctions or failures, unreliable data collection, or process activities that deviate from readily identified procedures. Experience at ICPP and prior evaluations at the Tokai reprocessing plant show that the use of process data can provide assurances that accountability measurement procedures are followed and SNM solutions are properly contained and can help confirm that SNM controls are in effect within a facility

Acoustic emission measurement during instrumented impact tests

International Nuclear Information System (INIS)

Crostack, H.A.; Engelhardt, A.H.

1983-01-01

Results of instrumented impact tests are discussed. On the one hand the development of the loading process at the hammer tup was recorded by means of a piezoelectric transducer. This instrumentation supplied a better representation of the load versus time than the conventional strain gauges. On the other hand the different types of acoustic emission occurring during a test could be separated. The acoustic emission released at the impact of the hammer onto the specimen is of lower frequency and its spectrum is strongly decreasing with increasing frequency. Plastic deformation also emits signals of lower frequency that are of quasi-continuous character. Both signal types can be discriminated by filtering. As a consequence typical burst signal were received afterwards that can be correlated with crack propagation. Their spectra exhibit considerable portions up to about 1.9 MHz. The development in time of the burst signals points to the kind of crack propagation resp. its sequence of appearance. However, definitive comparison between load and acoustic emission should become possible, only when the disadvantages of the common load measurement can be reduced, e.g. by determining the load directly at the specimen instead of the hammer tup

Draft Function Allocation Framework and Preliminary Technical Basis for Advanced SMR Concepts of Operations

Energy Technology Data Exchange (ETDEWEB)

Hugo, Jacques [Idaho National Lab. (INL), Idaho Falls, ID (United States); Forester, John [Idaho National Lab. (INL), Idaho Falls, ID (United States); Gertman, David [Idaho National Lab. (INL), Idaho Falls, ID (United States); Joe, Jeffrey [Idaho National Lab. (INL), Idaho Falls, ID (United States); Medema, Heather [Idaho National Lab. (INL), Idaho Falls, ID (United States); Persensky, Julius [Idaho National Lab. (INL), Idaho Falls, ID (United States); Whaley, April [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2013-08-01

This report presents preliminary research results from the investigation into the development of new models and guidance for Concepts of Operations in advanced small modular reactor (AdvSMR) designs. AdvSMRs are nuclear power plants (NPPs), but unlike conventional large NPPs that are constructed on site, AdvSMRs systems and components will be fabricated in a factory and then assembled on site. AdvSMRs will also use advanced digital instrumentation and control systems, and make greater use of automation. Some AdvSMR designs also propose to be operated in a multi-unit configuration with a single central control room as a way to be more cost-competitive with existing NPPs. These differences from conventional NPPs not only pose technical and operational challenges, but they will undoubtedly also have regulatory compliance implications, especially with respect to staffing requirements and safety standards.

Differences in safety margins between nuclear and conventional design standards with regards to seismic hazard definition and design criteria

International Nuclear Information System (INIS)

Elgohary, M.; Saudy, A.; Orbovic, N.; Dejan, D.

2006-01-01

With the surging interest in new build nuclear all over the world and a permanent interest in earthquake resistance of nuclear plants, there is a need to quantify the safety margins in nuclear buildings design in comparison to conventional buildings in order to increase the public confidence in the safety of nuclear power plants. Nuclear (CAN3-N289 series) and conventional (NBCC 2005) seismic standards have different approaches regarding the design of civil structures. The origin of the differences lays in the safety philosophy behind the seismic nuclear and conventional standards. Conventional seismic codes contain the minimal requirement destined primarily to safeguard against major structural failure and loss of life. It doesn't limit damage to a certain acceptable degree or maintain function. Nuclear seismic code requires that structures, systems and components important to safety, withstand the effects of earthquakes. The requirement states that for equipment important to safety, both integrity and functionality should be ascertained. The seismic hazard is generally defined on the basis of the annual probability of exceedence (return period). There is a major difference on the return period and the confidence level for design earthquakes between the conventional and the nuclear seismic standards. The seismic design criteria of conventional structures are based on the use of Force Modification Factors to take into account the energy dissipation by incursion in non-elastic domain and the reserve of strength. The use of such factors to lower intentionally the seismic input is consistent with the safety philosophy of the conventional seismic standard which is the 'non collapse' rather than the integrity and/or the operability of the structures or components. Nuclear seismic standard requires that the structure remain in the elastic domain; energy dissipation by incursion in non-elastic domain is not allowed for design basis earthquake conditions. This is

Basis Selectie Document voor de taakgebieden Volksgezondheid en Milieu en Rijksinstituut voor Volksgezondheid en Milieuhygiene RIV(M) 1940-1995

NARCIS (Netherlands)

BDA/RIVM; BDA; Rijksarchiefdienst/Pivot

1998-01-01

As laid down by Dutch national law the fundamental selection instrument (Basis Selectie Document, BSD) is to be used in national and regional government archives to separate records that should be preserved from records for which destruction is warranted. New archival legislation promulgated in 1995

Instrumented impact testing machine with reduced specimen oscillation effects

International Nuclear Information System (INIS)

Rintamaa, R.; Rahka, K.; Wallin, K.

1984-07-01

Owing to small and inexpensive specimens the Charpy impact test is widely used in quality control and alloy development. Limitations in power reactor survellance capsules it is also widely used for safety analysis purposes. Instrumenting the tup and computerizing data acquisition, makes dynamic fracture mechanics data measurement possible and convenient. However, the dynamic effects (inertia forces, specimen oscillations) in the impact test cause inaccuracies in the recorded load-time diagram and hence diminish the reliability of the calculated dynamic fracture mechanics parameters. To decrease inaccuracies a new pendulum type of instrumented impact test apparatus has been developed and constructed in the Metals Laboratory of the Technical Research Centre of Finland. This tester is based on a new principle involving inverted test geometry. The purpose of the geometry inversion is to reduce inertia load and specimen oscillation effects. Further, the new impact tester has some other novel features: e.g. the available initia impact energy is about double compared to the conventional standard (300 J) impact tester allowing the use of larger (10 x 20 x 110 mm) bend specimens than normal Charpy specimens. Also, the rotation asix in the three point bending is nearly stationary making COD-measurements possible. An experimental test series is described in which the inertia effects and specimen oscillations are compared in the conventional and new impact tester utilizing Charpy V-notch specimens. Comparison of the two test geometries is also made with the aid of an analytical model using finite element method (FEM) analysis. (author)

Sampled data spectroscopy (SDS): A new technology for radiation instrumentation

International Nuclear Information System (INIS)

Odell, D.M.C.

1992-01-01

A new instrumentation architecture for radiation spectroscopy is in the early stages of development at Savannah River. Based upon the same digital sampling techniques used in sonar and radar, sampled data spectroscopy (SDS) has produced Na(I)/PMT spectra with resolution comparable to conventional PHA systems. This work has laid the foundation for extending SDS techniques to solid state detector applications as well. Two-dimensional SDS processes raw, unintegrated detector output pulses to produce both energy and shape information that is used to construct a conventional energy spectrum. System advantages include zero electronic deadtime to support very high count rates, elimination of pulse pile-up peaks, high noise immunity, and digital system stability and reliability. Small size and low power requirements make 2-D SDS anideal technology for portable instrumentation and remote monitoring applications. Applications of potential interest at Savannah River include on-the-spot spill analysis, real-time waste stream monitoring, and personnel and area monitoring below background levels. A three-dimensional sampled data architecture is also being developed. Relying on image analysis and enhancement techniques, 3-D SDS identifies spectral peaks without determining the energy of any individual detector pulses. These techniques also open up a new avenue of exploration for reducing or removing Compton effects from the spectra of single detector systems. The intended application for this technique is waste characterization where lower energy isotopes are often obscured by the Compton scattering from dominant isotopes such as Csl37

Evaluation of conventional, protaper hand and protaper rotary instrumentation system for apical extrusion of debris, irrigants and bacteria- An in vitro randomized trial.

Science.gov (United States)

Kalra, Pinky; Rao, Arathi; Suman, Ethel; Shenoy, Ramya; Suprabha, Baranya-Shrikrishna

2017-02-01

Endodontic instrumentation carries the risk of over extrusion of debris and bacteria. The technique used and the type of instrumentation influences this risk. The purpose of this study was to evaluate and compare the K-file, ProTaper hand and ProTaper rotary instrumentation systems for the amount of apically extruded debris, irrigant solution and intracanal bacteria. Experimental single blinded randomized type of in vitro study with sample of 30 single rooted teeth. Endodontic access cavities were prepared and the root canals were filled with the suspension of E. faecalis . Myers and Montogomery Model was used to collect apically extruded debris and irrigant. Canals were prepared using K files, Hand protapers and Protaper rotary files. Non Parametric test like Kruskal-Wallis and Mann-Whitney U test were applied to determine the significant differences among the group. Tests revealed statistically significant difference between the amount of debris and number of bacteria extruded by the ProTaper hand and the K-files. No statistically significant difference was observed between the amounts of irrigant extruded by the ProTaper hand and the K-file system. Statistically significant differences were observed between the amounts of bacteria and irrigant extruded by the ProTaper rotary and the Protaper hand. No statistically significant difference was observed between the amounts of debris extruded by the ProTaper hand and the K-file system. Amount of apical extrusion of irrigant solution, bacteria and debris are significantly greater with K File instruments and least with Protaper rotary instruments. Key words: Protaper, rotary, periapical extrusion.

Conventional Gymnasium vs. Geodesic Field House. A Comparative Study of High School Physical Education and Assembly Facilities.

Science.gov (United States)

Educational Facilities Labs., Inc., New York, NY.

A description is presented of the design features of a high school's geodesic dome field house. Following consideration of various design features and criteria for the physical education facility, a comprehensive analysis is given of comparative costs of a geodesic dome field house and conventional gymnasium. On the basis of the study it would…

The Problems of Interpretation of the European Convention for the Protection of Human Rights and Fundamental Freedoms in the European Court of Human Rights

Directory of Open Access Journals (Sweden)

Ivanets Ivan Petrovich

2014-06-01

Full Text Available According to the clause 1 of Article 32 of the European Convention for the protection of Human Rights and Fundamental Freedoms of 1950 (hereinafter referred to as the European Convention or the Convention the competence of the European Court of Human Rights (hereinafter referred to as the Court or the Court extends to all issues of interpretation and application of the Convention and its protocols. Thus, the European Convention makes the Court the only tool of the way of understanding of the rights and freedoms protected by it. Interpretation of the provisions of Convention lies in the basis of the Court activity as immovable clod that stands guard for protection of human rights, and that is a place where the State is directly responsible before a human.

The bias and signal attenuation present in conventional pollen-based climate reconstructions as assessed by early climate data from Minnesota, USA.

Science.gov (United States)

St Jacques, Jeannine-Marie; Cumming, Brian F; Sauchyn, David J; Smol, John P

2015-01-01

The inference of past temperatures from a sedimentary pollen record depends upon the stationarity of the pollen-climate relationship. However, humans have altered vegetation independent of changes to climate, and consequently modern pollen deposition is a product of landscape disturbance and climate, which is different from the dominance of climate-derived processes in the past. This problem could cause serious signal distortion in pollen-based reconstructions. In the north-central United States, direct human impacts have strongly altered the modern vegetation and hence the pollen rain since Euro-American settlement in the mid-19th century. Using instrumental temperature data from the early 1800 s from Fort Snelling (Minnesota), we assessed the signal distortion and bias introduced by using the conventional method of inferring temperature from pollen assemblages in comparison to a calibration set from pre-settlement pollen assemblages and the earliest instrumental climate data. The early post-settlement calibration set provides more accurate reconstructions of the 19th century instrumental record, with less bias, than the modern set does. When both modern and pre-industrial calibration sets are used to reconstruct past temperatures since AD 1116 from pollen counts from a varve-dated record from Lake Mina, Minnesota, the conventional inference method produces significant low-frequency (centennial-scale) signal attenuation and positive bias of 0.8-1.7 °C, resulting in an overestimation of Little Ice Age temperature and likely an underestimation of the extent and rate of anthropogenic warming in this region. However, high-frequency (annual-scale) signal attenuation exists with both methods. Hence, we conclude that any past pollen spectra from before Euro-American settlement in this region should be interpreted using a pre-Euro-American settlement pollen set, paired to the earliest instrumental climate records. It remains to be explored how widespread this problem is

The bias and signal attenuation present in conventional pollen-based climate reconstructions as assessed by early climate data from Minnesota, USA.

Directory of Open Access Journals (Sweden)

Jeannine-Marie St Jacques

Full Text Available The inference of past temperatures from a sedimentary pollen record depends upon the stationarity of the pollen-climate relationship. However, humans have altered vegetation independent of changes to climate, and consequently modern pollen deposition is a product of landscape disturbance and climate, which is different from the dominance of climate-derived processes in the past. This problem could cause serious signal distortion in pollen-based reconstructions. In the north-central United States, direct human impacts have strongly altered the modern vegetation and hence the pollen rain since Euro-American settlement in the mid-19th century. Using instrumental temperature data from the early 1800 s from Fort Snelling (Minnesota, we assessed the signal distortion and bias introduced by using the conventional method of inferring temperature from pollen assemblages in comparison to a calibration set from pre-settlement pollen assemblages and the earliest instrumental climate data. The early post-settlement calibration set provides more accurate reconstructions of the 19th century instrumental record, with less bias, than the modern set does. When both modern and pre-industrial calibration sets are used to reconstruct past temperatures since AD 1116 from pollen counts from a varve-dated record from Lake Mina, Minnesota, the conventional inference method produces significant low-frequency (centennial-scale signal attenuation and positive bias of 0.8-1.7 °C, resulting in an overestimation of Little Ice Age temperature and likely an underestimation of the extent and rate of anthropogenic warming in this region. However, high-frequency (annual-scale signal attenuation exists with both methods. Hence, we conclude that any past pollen spectra from before Euro-American settlement in this region should be interpreted using a pre-Euro-American settlement pollen set, paired to the earliest instrumental climate records. It remains to be explored how widespread

Instrumental interaction

OpenAIRE

Luciani , Annie

2007-01-01

International audience; The expression instrumental interaction as been introduced by Claude Cadoz to identify a human-object interaction during which a human manipulates a physical object - an instrument - in order to perform a manual task. Classical examples of instrumental interaction are all the professional manual tasks: playing violin, cutting fabrics by hand, moulding a paste, etc.... Instrumental interaction differs from other types of interaction (called symbolic or iconic interactio...

Volkov basis for simulation of interaction of strong laser pulses and solids

Science.gov (United States)

Kidd, Daniel; Covington, Cody; Li, Yonghui; Varga, Kálmán

2018-01-01

An efficient and accurate basis comprised of Volkov states is implemented and tested for time-dependent simulations of interactions between strong laser pulses and crystalline solids. The Volkov states are eigenstates of the free electron Hamiltonian in an electromagnetic field and analytically represent the rapidly oscillating time-dependence of the orbitals, allowing significantly faster time propagation than conventional approaches. The Volkov approach can be readily implemented in plane-wave codes by multiplying the potential energy matrix elements with a simple time-dependent phase factor.

Customisation of an instrument to assess anaesthesiologists' non-technical skills

DEFF Research Database (Denmark)

Jepsen, Rikke M H G; Spanager, Lene; Lyk-Jensen, Helle T

2015-01-01

operating room team members: anaes-thesiologists, nurse anaesthetists, surgeons, and scrub nurses. Interviews were transcribed verbatim and analysed using directed content analysis. Anaesthesiologists' non-technical skills were identified, coded, and sorted using the original instrument as a basis......; decision making; team working; and task management. Anaesthesiologists' leadership role in the operating room was emphasised: the original 'Task Management' category was named 'Leadership'. One new element, 'Demonstrating self-awareness' was added under the category 'Situation Awareness'. Compared...

Basis set approach in the constrained interpolation profile method

International Nuclear Information System (INIS)

Utsumi, T.; Koga, J.; Yabe, T.; Ogata, Y.; Matsunaga, E.; Aoki, T.; Sekine, M.

2003-07-01

We propose a simple polynomial basis-set that is easily extendable to any desired higher-order accuracy. This method is based on the Constrained Interpolation Profile (CIP) method and the profile is chosen so that the subgrid scale solution approaches the real solution by the constraints from the spatial derivative of the original equation. Thus the solution even on the subgrid scale becomes consistent with the master equation. By increasing the order of the polynomial, this solution quickly converges. 3rd and 5th order polynomials are tested on the one-dimensional Schroedinger equation and are proved to give solutions a few orders of magnitude higher in accuracy than conventional methods for lower-lying eigenstates. (author)

Minimization of Basis Risk in Parametric Earthquake Cat Bonds

Science.gov (United States)

Franco, G.

2009-12-01

A catastrophe -cat- bond is an instrument used by insurance and reinsurance companies, by governments or by groups of nations to cede catastrophic risk to the financial markets, which are capable of supplying cover for highly destructive events, surpassing the typical capacity of traditional reinsurance contracts. Parametric cat bonds, a specific type of cat bonds, use trigger mechanisms or indices that depend on physical event parameters published by respected third parties in order to determine whether a part or the entire bond principal is to be paid for a certain event. First generation cat bonds, or cat-in-a-box bonds, display a trigger mechanism that consists of a set of geographic zones in which certain conditions need to be met by an earthquake’s magnitude and depth in order to trigger payment of the bond principal. Second generation cat bonds use an index formulation that typically consists of a sum of products of a set of weights by a polynomial function of the ground motion variables reported by a geographically distributed seismic network. These instruments are especially appealing to developing countries with incipient insurance industries wishing to cede catastrophic losses to the financial markets because the payment trigger mechanism is transparent and does not involve the parties ceding or accepting the risk, significantly reducing moral hazard. In order to be successful in the market, however, parametric cat bonds have typically been required to specify relatively simple trigger conditions. The consequence of such simplifications is the increase of basis risk. This risk represents the possibility that the trigger mechanism fails to accurately capture the actual losses of a catastrophic event, namely that it does not trigger for a highly destructive event or vice versa, that a payment of the bond principal is caused by an event that produced insignificant losses. The first case disfavors the sponsor who was seeking cover for its losses while the

Scanning electron microscope - some aspects of the instrument and its applications

International Nuclear Information System (INIS)

Thatte, M.R.

1976-01-01

Development of the science of microscopy leading to three different types of microscopes - the optical, the conventional transmission electron microscope (CTEM) and the scanning electron microscope(SEM) has been discussed. Special advantages of the SEM in the solution of problems in industrial laboratories are mentioned. A brief reference to the latest instruments announced by Siemens AG shows the modern trends in the technique. A close similarity in image building between SEM and television is indicated. Operational anatomy of the SEM is reviewed. (author)

Outcome indicators for the evaluation of energy policy instruments and technical change

International Nuclear Information System (INIS)

Neij, Lena; Astrand, Kerstin

2006-01-01

The aim of this paper is to propose a framework for the evaluation of policy instruments designed to affect development and dissemination of new energy technologies. The evaluation approach is based on the analysis of selected outcome indicators describing the process of technical change, i.e. the development and dissemination of new energy technologies, on the basis of a socio-technical systems approach. The outcome indicators are used to analyse the effect, in terms of outcome, and outcome scope of the policy instruments as well as the extent to which the policy instruments support diversity, learning and institutional change. The analysis of two cases of evaluations, of energy efficiency policy and wind energy policy in Sweden, shows that the approach has several advantages, allowing continuous evaluation and providing important information for the redesign of policy instruments. There are also disadvantages associated with the approach, such as complexity, possible high cost and the requirement of qualified evaluators. Nevertheless, it is concluded that the information on the continuous performance of different policy instruments and their effects on the introduction and dissemination of new energy technologies, provided by this evaluation approach, is essential for an improved adaptation and implementation of energy and climate policy

Instrumentation and electrical program at the Three Mile Island Unit 2, Technical Integration Office

International Nuclear Information System (INIS)

Hecker, L.A.

1982-01-01

The Three Mile Island Unit 2 accident of March 28, 1979 presents unique research opportunities that can provide valuable information on nuclear power plant safety philosophy and safety systems performance. The Technical Integration Office at Three Mile Island was established by the Department of Energy to manage a broad-based research and development program. One significant part of this effort is the Instrumentation and Electrical Program, which operates: (1) to identify instruments and electrical components that failed during or since the accident; (2) to test and analyze them in order to identify the causes of failure; and (3) to assess the survivability of those that did not fail. The basis for selection of equipment is discussed, and the testing methodology is described. Also, some results of Instrumentation and Electrical Program work to date are presented

Influence of cyclical fatigue on torsional fracture morphology in endodontic instruments.

Science.gov (United States)

Lopreite, Gustavo; Basilaki, Jorge; Hecht, Pedro

2013-01-01

Cyclical fatigue may influence the appearance and propagation of the type of fracture of an endodontic instrument. The aim of this study was to assess the influence of cyclic fatigue on morphological features of torsional fracture in Pathfile nickel-titanium rotary instruments for surgical preparation in endodontics. Thirty new Pathfile instruments (Dentsply- Maillefer. Ballaigues-Switzerland) diameter .13 and taper .02 were randomly divided into 5 groups (n = 6). Twenty-four of them were subject to cyclical fatigue by continuous rotation using a stainless steel cylinder with internal bore 0.5 mm, length 25 mm, with a curve of 45 degrees and radius 8 mm at 5 mm from the tip, at 300 rpm and 1 Ncm torque for different times: A: 15 sec, B: 75 sec, C: 150 sec and D: 300 sec, while the fifth group was kept as a control (group N). As a second step, the instruments were rotated at 2 rpm and 1 Ncm torque, with their apical 3 mm fixed in a resin block until they suffered torsional fracture. The fracture surfaces were analyzed using a conventional high-vacuum scanning electron microscope (Phillips mod. 515) at 400x. All instruments had ductile fracture areas of different sizes. The ductile fracture areas were measured as percentages of the total area of the instrument by means of Golden Ratio (Softonic) software for measuring images. The data obtained were analyzed statistically using one-way variance analysis followed by Tukey's multiple comparison test. There were significant differences among groups regarding cyclic fatigue time and fragile fracture area (P fatigue to which the rotating PathFile instrument is subject significantly increases the percentage of ductile fracture area produced by torsion.

Third National Report on compliance with the Joint Convention Obligations

International Nuclear Information System (INIS)

2008-09-01

The Joint Convention on the Safety of Spent Fuel Management and the Safety of Radioactive Waste Management, hereinafter referred to as the 'Joint Convention', is the result of international discussions that followed the adoption of the Convention on Nuclear Safety, in 1994. France signed the Joint Convention at the General Conference of the International Atomic Energy Agency (IAEA) held on 29 September 1997, the very first day the Joint Convention was opened for signature. She approved it on 22 February 2000 and filed the corresponding instruments with the IAEA on 27 April 2000. The Joint Convention entered into force on 18 June 2001. For many years, France has been taking an active part in the pursuit of international actions to reinforce nuclear safety and considers the Joint Convention to be a key step in that direction. The fields covered by the Joint Convention have long been part of the French approach to nuclear safety. This report is the third one of its kind. It is published in accordance with Article 32 of the Joint Convention and presents the measures taken by France to meet each of her obligations set out in the Convention. The facilities and the radioactive materials covered by this Convention are quite diversified in nature and are controlled in France by different regulatory authorities. Above a specific threshold of radioactive content, a facility is referred to as a 'basic nuclear facility' (installation nucleaire de base - INB) and placed under the control of the Nuclear Safety Authority (Autorite de surete nucleaire - ASN). Below that threshold and provided that the facility involved is subject to the nomenclature of classified facilities for other purposes than their radioactive materials, any facility may be considered as a 'classified facility on environmental-protection grounds' (installation classee pour la protection de l'environnement - ICPE) and placed under the control of the Ministry for the Environment. Facilities that contain only

Instrumentation development

International Nuclear Information System (INIS)

Ubbes, W.F.; Yow, J.L. Jr.

1988-01-01

Instrumentation is developed for the Civilian Radioactive Waste Management Program to meet several different (and sometimes conflicting) objectives. This paper addresses instrumentation development for data needs that are related either directly or indirectly to a repository site, but does not touch on instrumentation for work with waste forms or other materials. Consequently, this implies a relatively large scale for the measurements, and an in situ setting for instrument performance. In this context, instruments are needed for site characterization to define phenomena, develop models, and obtain parameter values, and for later design and performance confirmation testing in the constructed repository. The former set of applications is more immediate, and is driven by the needs of program design and performance assessment activities. A host of general technical and nontechnical issues have arisen to challenge instrumentation development. Instruments can be classed into geomechanical, geohydrologic, or other specialty categories, but these issues cut across artificial classifications. These issues are outlined. Despite this imposing list of issues, several case histories are cited to evaluate progress in the area

Instrumentation

International Nuclear Information System (INIS)

Decreton, M.

2002-01-01

SCK-CEN's R and D programme on instrumentation involves the development of advanced instrumentation systems for nuclear applications as well as the assessment of the performance of these instruments in a radiation environment. Particular emphasis is on the use of optical fibres as umbilincal links of a remote handling unit for use during maintanance of a fusion reacor, studies on the radiation hardening of plasma diagnostic systems; investigations on new instrumentation for the future MYRRHA accelerator driven system; space applications related to radiation-hardened lenses; the development of new approaches for dose, temperature and strain measurements; the assessment of radiation-hardened sensors and motors for remote handling tasks and studies of dose measurement systems including the use of optical fibres. Progress and achievements in these areas for 2001 are described

Instrumentation

Energy Technology Data Exchange (ETDEWEB)

Decreton, M

2002-04-01

SCK-CEN's R and D programme on instrumentation involves the development of advanced instrumentation systems for nuclear applications as well as the assessment of the performance of these instruments in a radiation environment. Particular emphasis is on the use of optical fibres as umbilincal links of a remote handling unit for use during maintanance of a fusion reacor, studies on the radiation hardening of plasma diagnostic systems; investigations on new instrumentation for the future MYRRHA accelerator driven system; space applications related to radiation-hardened lenses; the development of new approaches for dose, temperature and strain measurements; the assessment of radiation-hardened sensors and motors for remote handling tasks and studies of dose measurement systems including the use of optical fibres. Progress and achievements in these areas for 2001 are described.

An intelligent instrument for measuring exhaust temperature of marine engine

Science.gov (United States)

Ma, Nan-Qi; Su, Hua; Liu, Jun

2006-12-01

Exhaust temperature of the marine engine is commonly measured through thermocouple. Measure deviation will occur after using the thermocouple for some time due to nonlinearity of thermocouple itself, high temperature and chemical corrosion of measure point. Frequent replacement of thermocouple will increase the operating cost. This paper designs a new intelligent instrument for solving the above-mentioned problems of the marine engine temperature measurement, which combines the conventional thermocouple temperature measurement technology and SCM(single chip microcomputer). The reading of the thermocouple is simple and precise and the calibration can be made automatically and manually.

The polarized neutron small-angle scattering instrument at BENSC Berlin

International Nuclear Information System (INIS)

Keller, T.; Krist, T.; Danzig, A.; Keiderling, U.; Mezei, F.; Wiedenmann, A.

2000-01-01

A polarized neutron beam has been installed at the small-angle neutron-scattering instrument V4 at BENSC Berlin. The main component of this new option is a 1.8 m long cavity transmission polarizer. The advantages of this device compared to the conventional bender polarizers are: (i) high transmission (35% of unpolarized beam at λ=6 A); (ii) the polarization is better than 93% in the wavelength band 4 A 3 O 4 particles embedded in a glass matrix) are presented and compared to a measurement with unpolarized neutrons

An in vitro assessment of the physical properties of novel Hyflex nickel-titanium rotary instruments.

Science.gov (United States)

Peters, O A; Gluskin, A K; Weiss, R A; Han, J T

2012-11-01

To determine several properties including torsional and fatigue limits, as well as torque during canal preparation, of Hyflex, a rotary instrument manufactured from so-called controlled memory nickel-titanium alloy. The instruments were tested in vitro using a special torque bench that permits both stationary torque tests according to ISO3630-1 and fatigue limit determination, as well as measurement of torque (in Ncm) and apical force (in N) during canal preparation. Fatigue limit (in numbers of cycles to failure) was determined in a 90°, 5 mm radius block-and-rod assembly. Simulated canals in plastic blocks were prepared using both a manufacturer-recommended single-length technique as well as a generic crown-down approach. anova with Bonferroni post hoc procedures was used for statistical analysis. Torque at failure ranged from 0.47 to 1.38 Ncm, with significant differences between instrument sizes (P instruments size 20, .04 taper and size 25, .08 taper, respectively. Torque during canal preparation was significantly higher for small instruments used in the single-length technique but lower for the size 40, .04 taper, compared to a crown-down approach. No instrument fractured; 82% of the instruments used were plastically deformed; however, only 37% of these remained deformed after a sterilization cycle. Hyflex rotary instruments are bendable and flexible and have similar torsional resistance compared to instruments made of conventional NiTi. Fatigue resistance is much higher, and torque during preparation is less, compared to other rotary instruments tested previously under similar conditions. © 2012 International Endodontic Journal.

The Effects of Degraded Digital Instrumentation and Control Systems on Human-system Interfaces and Operator Performance: HFE Review Guidance and Technical Basis

Energy Technology Data Exchange (ETDEWEB)

O' Hara, J.M.; W. Gunther, G. Martinez-Guridi

2010-02-26

New and advanced reactors will use integrated digital instrumentation and control (I&C) systems to support operators in their monitoring and control functions. Even though digital systems are typically highly reliable, their potential for degradation or failure could significantly affect operator performance and, consequently, impact plant safety. The U.S. Nuclear Regulatory Commission (NRC) supported this research project to investigate the effects of degraded I&C systems on human performance and plant operations. The objective was to develop human factors engineering (HFE) review guidance addressing the detection and management of degraded digital I&C conditions by plant operators. We reviewed pertinent standards and guidelines, empirical studies, and plant operating experience. In addition, we conducted an evaluation of the potential effects of selected failure modes of the digital feedwater system on human-system interfaces (HSIs) and operator performance. The results indicated that I&C degradations are prevalent in plants employing digital systems and the overall effects on plant behavior can be significant, such as causing a reactor trip or causing equipment to operate unexpectedly. I&C degradations can impact the HSIs used by operators to monitor and control the plant. For example, sensor degradations can make displays difficult to interpret and can sometimes mislead operators by making it appear that a process disturbance has occurred. We used the information obtained as the technical basis upon which to develop HFE review guidance. The guidance addresses the treatment of degraded I&C conditions as part of the design process and the HSI features and functions that support operators to monitor I&C performance and manage I&C degradations when they occur. In addition, we identified topics for future research.

Application of ‘Urf In Islamic and Conventional Bank

Directory of Open Access Journals (Sweden)

Shafi‘i Abdul Azeez Bello

2013-06-01

Full Text Available ‘Urf or Customary law is one of the most important supporting sources in Islamic law. This can be seen through many legal rulings (ahkam in Islamic law, which was based on ‘urf in which most of these ahkam will change according to the change of circumstances, place and time. As for basis of ‘urf or custom, it is the product of the nature of the people and their culture, it grows in strength and popularity by means of imitation that transfers and implants it in the lives of people. Moreover, Contemporary financial system poses great problem and even great challenges to Muslims. Muslims are not permitted by Islamic Law to indulge in ribā. Since contemporary financial system is based on interest, Muslims have great problems in participating in it. Therefore, this paper stands to explain the application of ‘urf in Islamic and conventional Bank. The concept and principle of ‘urf in Islamic law was critically analysed such as application of ‘urf in Islamic law, differences between ‘urf and consensus of jurists, also between ‘urf and adah, in addition, classification of ‘urf, conditions of valid ‘urf and so on. Furthermore, the application of ‘urf in deposit products under Islamic and Conventional bank were well examined, types of conventional deposit products as well as Islamic deposit products. In fact the product shows that a little different was in-between them which can be easily avoid.

Application of ‘Urf In Islamic and Conventional Bank

Directory of Open Access Journals (Sweden)

Shafi‘i Abdul Azeez Bello

2013-06-01

Full Text Available  ‘Urf or Customary law is one of the most important supporting sources in Islamic law. This can be seen through many legal rulings (ahkam in Islamic law, which was based on ‘urf in which most of these ahkam will change according to the change of circumstances, place and time. As for basis of ‘urf or custom, it is the product of the nature of the people and their culture, it grows in strength and popularity by means of imitation that transfers and implants it in the lives of people. Moreover, Contemporary financial system poses great problem and even great challenges to Muslims. Muslims are not permitted by Islamic Law to indulge in ribā. Since contemporary financial system is based on interest, Muslims have great problems in participating in it. Therefore, this paper stands to explain the application of ‘urf in Islamic and conventional Bank. The concept and principle of ‘urf in Islamic law was critically analysed such as application of ‘urf in Islamic law, differences between ‘urf and consensus of jurists, also between ‘urf and adah, in addition, classification of ‘urf, conditions of valid ‘urf and so on. Furthermore, the application of ‘urf in deposit products under Islamic and Conventional bank were well examined, types of conventional deposit products as well as Islamic deposit products. In fact the product shows that a little different was in-between them which can be easily avoid.

Comparison Of INAA Methods (Long Conventional, Cyclic And Pseudo-Cyclic) For The Determination Of Se In Biological Samples

International Nuclear Information System (INIS)

Sarheel, A.

2004-01-01

Selenium content in serum blood, sample were received from international comparison programme (SABC) has been determined by Cyclic irradiation, pseudo-cyclic irradiation and long irradiation conventional Instrumental neutron activation analysis through the 162 keV gamma ray of the 77m Se nuclide for both cyclic and pseudo-cyclic and 264 keV gamma ray of 75 Se nuclide for conventional (long irradiation). The CINAA involve irradiation of samples for 20 s, decay for 15 s and counting for 20 s, samples recycling four times to improve the precision. The PCINAA involve irradiation of samples for 20 s, decay for 20 s and counting for 30s, samples recycling four times day by day. The Conventional (long irradiation) involve irradiation of samples for 20 hr (1 week), decay for 4 weeks and counting for 20 hr. The accuracy has been evaluated by analyzing the certified reference materials. (Author)

Instrument for analysis of electric motors based on slip-poles component

Science.gov (United States)

Haynes, Howard D.; Ayers, Curtis W.; Casada, Donald A.

1996-01-01

A new instrument for monitoring the condition and speed of an operating electric motor from a remote location. The slip-poles component is derived from a motor current signal. The magnitude of the slip-poles component provides the basis for a motor condition monitor, while the frequency of the slip-poles component provides the basis for a motor speed monitor. The result is a simple-to-understand motor health monitor in an easy-to-use package. Straightforward indications of motor speed, motor running current, motor condition (e.g., rotor bar condition) and synthesized motor sound (audible indication of motor condition) are provided. With the device, a relatively untrained worker can diagnose electric motors in the field without requiring the presence of a trained engineer or technician.

Vision though afocal instruments: generalized magnification and eye-instrument interaction

Science.gov (United States)

Harris, William F.; Evans, Tanya

2018-04-01

In Gaussian optics all observers experience the same magnification, the instrument's angular magnification, when viewing distant objects though a telescope or other afocal instruments. However, analysis in linear optics shows that this is not necessarily so in the presence of astigmatism. Because astigmatism may distort and rotate images it is appropriate to work with generalized angular magnification represented by a 2 × 2 matrix. An expression is derived for the generalized magnification for an arbitrary eye looking through an arbitrary afocal instrument. With afocal instruments containing astigmatic refracting elements not all eyes experience the same generalized magnification; there is interaction between eye and instrument. Eye-instrument interaction may change as the instrument is rotated about its longitudinal axis, there being no interaction in particular orientations. A simple numerical example is given. For sake of completeness, expressions for generalized magnification are also presented in the case of instruments that are not afocal and objects that are not distant.

MODERN MARKETING CONCEPTS AS THE BASIS FOR FORMATION AND INCREASE OF THE ATTRACTIVENESS OF CITIES AND TERRITORIES

Directory of Open Access Journals (Sweden)

Iryna Budnikevych

2017-11-01

Full Text Available Instruments of formation and increase of attractiveness of the territory within the framework of modern marketing conceptions, the role of marketing complex elements in shaping the attractiveness of the territories are examined, separate economical categories, forming notional instrument of the attractiveness of the territories are specified and proposals concerning the directions of marketing efforts are formulated. Methodology. Theoretical and methodological basis of the research is the work of scientists on marketing problems of the city, theory of I. Budnikevych, identifying the characteristics of territorial marketing (municipal, city marketing within industrial, commodity, sale, classical, social-ethic and partnership conceptions. The authors used the combination of following methods in the process of scientific investigation: method of generalization and scientific abstraction – for concrete definition of notional-categorial apparatus; analytical monographic method – to represent scientific thoughts on the directions of marketing instruments application in the processes of territorial attractiveness management; comparative analysis – to find out the peculiarities of marketing instruments and methods use within the limits of different concepts and at different stages of territorial development. Practical value. It was defined that territorial marketing system allows to expand traditional approaches to the policy of regional and local authority’s attractiveness, supplementing them with modern components and characteristics. Nowadays, the instruments of situational conceptions are still actively applied by homeland and foreign territorial marketing practice, sale conception in particular, which stipulates the direction of territorial authorities’ activity to satisfy territorial needs. The instruments of modern territorial marketing conceptions allow to form and increase the attractiveness of territories for defined target audiences

Instrument development continues in Oak Ridge

International Nuclear Information System (INIS)

Ekkebus, Allen E.

2012-01-01

Peer review panels composed of 80 external scientists recently visited Oak Ridge National Laboratory (ORNL) to review almost 700 proposals for experiments on 23 instruments at the Spallation Neutron Source (SNS) and High Flux Isotope Reactor (HFIR). These were proposed for the time period from January-June 2012. About 40% of the proposals were approved for beam time and 20% were placed on an alternate list if time becomes available. The Hybrid Spectrometer HYSPEC at SNS began its commissioning in September 2011. HYSPEC is otpimized for studying low energy dynamics in single-crystal samples using a broad variety of sample environments, and is equipped with a polarization analysis capability. It is expected to be available for users on a limited basis in the second half of 2012. The detector tank of CORELLI has been installed on beamline 9 at SNS. Now that the tank is in place, banks of neutron detectors and boron carbide shielding will be installed around the interior. CORELLI is optimized to probe complex disorder in crystalline materials through diffuse scattering from single-crystal samples. It will begin commissioning in 2014. CORELLI is one of four instruments being developed under the SING II (SNS Instruments Next Generation II) project. The others are the Macromolecular Neutron Diffractometer (MANDI), the Vibrational Spectrometer (VISION, scheduled to begin commissioning in 2012), and the Time of Flight Ultra Small Angle Neutron Scattering Instrument (TOF-USANS). The single crystal neutron diffractometer IMAGINE, was deliverd to HFIR in October 2011. Preliminary testing has been carried out. IMAGINE will provide atomic resolution information on chemical, organic, metallo-organic and protein single crystals that will enable their chemical, physical and biological structure and function to be understood. This instrument will benefit scientists with interests in pharmaceuticals, minerals and other inorganic crystals, small molecules, molecular organo

France - convention on nuclear safety. Fifth national report for the 2011 peer review meeting

International Nuclear Information System (INIS)

2010-01-01

The Convention on Nuclear Safety, hereinafter referred to as 'the Convention', is one of the results of international discussions initiated in 1992 in order to contribute maintaining a high level of nuclear safety worldwide. The convention aims to propose binding international obligations regarding nuclear safety. France signed the Convention on 20 September 1994, the date on which it was opened for signature during the IAEA's General Conference, and approved it on 13 September 1995. The Convention entered into force on 24 October 1996. For many years France has been participating actively in international initiatives to enhance nuclear safety, and it considers the Convention on Nuclear Safety to be an important instrument for achieving this aim. The areas covered by the Convention have long been part of the French approach to nuclear safety. The purpose of this fifth report, which was drafted pursuant to Article 5 of the Convention on Nuclear Safety, is to present the measures taken by France in order to fulfil each of her obligations as specified in the said Convention. Since the Convention applies to all nuclear-power generating reactors, most of this report is dedicated to the measures taken in order to ensure their safety. However, as in previous reports, France has decided to present also in this fifth report, the measures that were taken for all research reactors, together with a graduated approach, if need be, for taking their size into account. First of all, research reactors are actually submitted to the same overall regulations as nuclear-power reactors with regard to safety and radiation protection. It should be noted that the most powerful French research reactor, called Phenix, which also used to produce electricity, was disconnected from the grid in March 2009, but continued to run an 'ultimate-test programme' until 1 February 2010. Later, in the framework of the Joint Convention on the Safety of Spent Fuel Management and the Safety of Radioactive

System requirements and design description for the document basis database interface (DocBasis)

International Nuclear Information System (INIS)

Lehman, W.J.

1997-01-01

This document describes system requirements and the design description for the Document Basis Database Interface (DocBasis). The DocBasis application is used to manage procedures used within the tank farms. The application maintains information in a small database to track the document basis for a procedure, as well as the current version/modification level and the basis for the procedure. The basis for each procedure is substantiated by Administrative, Technical, Procedural, and Regulatory requirements. The DocBasis user interface was developed by Science Applications International Corporation (SAIC)

Deformation and fracture of Mtwo rotary nickel-titanium instruments after clinical use.

Science.gov (United States)

Inan, Ugur; Gonulol, Nihan

2009-10-01

In recent years, a number of rotary nickel titanium (NiTi) systems have been developed to provide better, faster, and easier cleaning and shaping of the root canal system. Although the NiTi instruments are more flexible than the stainless steel files, the main problem with the rotary NiTi instruments is the failure of the instruments. The aim of this study was to evaluate the deformation and fracture rate of Mtwo rotary nickel-titanium instruments (VDW, Munich, Germany) discarded after routine clinical use. A total of 593 Mtwo rotary NiTi instruments were collected after clinical use from the clinic of endodontics over 12 months. The length of the files was measured using a digital caliper to determine any fracture, and then all the files were evaluated under a stereomicroscope for defects such as unwinding, curving, or bending and fracture. The fracture faces of separated files were also evaluated under a scanning electron microscope. The data were analyzed using a chi-square and z test. A percentage of all files (25.80%) showed defects, and the major defect was fracture (16.02%). The most frequently fractured file was #10.04 (30.39%). Deformations without fracture were mostly observed on #15.05 files (25.47%). A higher rate of deformation was observed for #10.04 and #15.05 files. Therefore, these files should be considered as single-use instruments. Because cyclic fatigue was the cause of 71.58% of the instrument fractures, it is also important not to exceed the maximum number of usage recommended by the manufacturer and discard the instruments on a regular basis.

Design of Simple Instrumentation System for the Quality Analysis of Milk (Casein Analysis

Directory of Open Access Journals (Sweden)

V. G. Sangam

2010-08-01

Full Text Available This paper describes the design of a simple instrumentation system for the analysis of casein concentration in the milk. Casein is one of the major constituent of milk and its concentration describes the quality of the milk. Normally casein is analyzed by conventional analytical methods or by using Spectrophotometric methods. Here an attempt has been made to develop a simple portable system using optical instrumentation technique. The objective of the developed system is the real time analysis of the casein concentration of the milk at the field. The system involves UV light source, UV filter, cuvette, photo detector, display unit, data Acquisition Card (DAC as peripheral with USB port. Appropriate program has been developed in visual studio 6 and turbo C. Repeated number of real time analysis was carried out for different samples of milk; the results obtained are in excellent agreement with the amount determined by standard conventional methods with an accuracy of ±1.5 %, and the response time is within 100 seconds. This system can be used in the field for the quality analysis of milk as an independent unit and can also be interfaced to PC with USB port. The system has good accuracy, less response time and low cost.

Pest management strategies: Area-wide and conventional

International Nuclear Information System (INIS)

Lindquist, D.A.

2000-01-01

part of the cost of an area-wide programme will be fighting the target pest away from the commercial production - before the commercial crops are susceptible - on wild or alternate hosts or abandoned orchards, untreated host plants in homeowners' gardens, etc. In most cases, area-wide insect control will be the responsibility of a separate organisation hired by the producers. A separate organisation can plan an aggressive offense against the target pest population over the entire area. High technology systems can be effectively utilised to plan the population management programme. Included will be satellite imagery to detect alternate hosts, sensitive methods to detect movement of the pest populations, computer programmes to predict changes in the pest insect population based on biological parameters, a systems approach to utilise natural enemies on an area-wide basis, genetic analysis to detect the development of resistance and utilisation of systems to delay the development of resistance over the total area. Further, area-wide programmes encourage the use of specialised methods of insect control that are not effective or are not used on a farm by farm basis. These include the sterile insect technique (SIT), male annihilation, inundative releases of parasites, mating inhibitors, large-scale trap cropping with very attractive plants, treatment of alternate hosts on public lands and hosts in private gardens, etc. The objective of area-wide control is to reduce the pest population within the target area to a non-economic level. This is accomplished by attacking the entire insect pest population in the target area. Conventional insect control attempts to protect the plant or animal, is carried out by individual producers over a small area with little planning, is short-term, low technology and is a reactive (defense) approach to insect control. Area-wide insect control attempts to reduce the pest population to a non-economic level over a large area involving many

Assessing Volatilities of Monetary Policy and their Effects on the Islamic and Conventional Stock Markets in Indonesia

Directory of Open Access Journals (Sweden)

M Shabri Abd Majid

2018-03-01

Full Text Available The main objective of this study is to empirically assess the volatilities of the monetary policy instruments and their effects on the Indonesian Islamic and conventional stock market. The changes in exchange rate, interest rates, and money supply and their effects on the stock markets are investigated using the using the Generalized Autoregressive Conditional Heteroskedasticity frameworks. As a big-open economy, the capital market of Indonesia is vulnerable to the global monetary shocks changes, thus the US federal funds rate is also incorporated into the GARCH model. The study documented that, with the exception of the US interest rate, the volatilities of all monetary policy variables of interest rate, exchange rate, and money supply were documented affecting the volatilities of both Islamic and conventional stock markets. These findings imply that the volatilities of Islamic and conventional stock markets have similar determinants, thus to stabilize the markets, the investigated monetary policy variables should be controlled for by the policy-makers. Any monetary policy design imposed by the policy-makers would have a similar effect on both conventional and Islamic stocks in Indonesia.DOI: 10.15408/sjie.v7i2.7352

Protective interest rate as tax instrument of corporate capital protection

Directory of Open Access Journals (Sweden)

Vukašinović Jovan

2015-01-01

Full Text Available This paper deals with researching negative consequences of allocation of economic (virtual gains made as a result of conventional accounting concept by facing current income with historical expenses and necessity to promote additional stimulating instruments that are at disposal by the state in order to eliminate these negative consequences. one of them is certainly protective interest as a relatively new active fiscal instrument of capital protection and recognition of price of invested owner's equity in business ventures, i.e. a specific form of compensation by the state for invested capital bearing in mind, that no source is free, including ones own sources. We also showed mechanisms of protective interest which, together with other measures of macroeconomic policy, should contribute to the protection of real purchasing power of company equity and increase of net gain, left on company's disposal for new investments, new work places, more money in the budget, protection of actual assets against taxing in the conditions of inflation, etc.

Gender Mainstreaming or Instrumentalization of Women?

Directory of Open Access Journals (Sweden)

Marie France Labrecque

2010-09-01

Full Text Available This question is discussed on the basis of first hand data collected in Mexico between 2004 and 2007. The research aimed at examining how gender equity policies elaborated at the international level using an approach known as “gender mainstreaming” are transformed within national and local contexts. In a first step, the context of the emergence of the gender mainstreaming approach is reconstituted, and in a second step we try to clarify how and under what circumstances, in a country like Mexico, women can be instrumentalized within this approach, as for example, when gender mainstreaming is applied without any critical vision as it is so under neoliberalism. The main example rests on the case of microcredit for maya women in the state of Yucatan.

Detecting The Expected Rate of Return Volatility of Financing Instruments of Indonesian Islamic Banking through GARCH Modeling (Generalized Autoregressive Conditional Heteroscedasticity

Directory of Open Access Journals (Sweden)

Nurul Huda

2015-04-01

Full Text Available Objective - Islamic banks are banks which its activities, both fund raising and funds distribution are on the basis of Islamic principles, namely buying and selling and profit sharing. Islamic banking is aimed at supporting the implementation of national development in order to improve justice, togetherness, and equitable distribution of welfare. In pursuit of supporting the implementation of national development, Islamic banking often faced stability problems of financing instruments being operated. In this case, it is measured by the gap between the actual rate of return and the expected rate of return. The individual actual RoR of this instrument will generate an expected rate of return. This raises the gap or difference between the actual rate of return and the expected rate of return of individual instruments, which in this case is called the abnormal rate of return. The stability of abnormal rate of return of individual instruments is certainly influenced by the stability of the expected rate of return. Expected rate of return has a volatility or fluctuation levels for each financing instrument. It is also a key element or material basis for the establishment of a variance of individual instruments. Variance in this case indicates the level of uncertainty of the rate of return. Individual variance is the origin of the instrument base for variance in the portfolio finance that further a portfolio analysis. So, this paper is going to analyze the level of expected RoR volatility as an initial step to see and predict the stability of the fluctuations in the rate of return of Indonesian Islamic financing instruments.Methods – Probability of Occurence, Expected Rate of Return (RoR and GARCH (Generalized Autoregressive Conditional Heteroscedasticity.Results - The expected RoR volatility of the murabaha and istishna financing instruments tend to be more volatile than expected RoR volatility of musharaka and qardh financing instruments

Environmental conditions using thermal-hydraulics computer code GOTHIC for beyond design basis external events

International Nuclear Information System (INIS)

Pleskunas, R.J.

2015-01-01

In response to the Fukushima Dai-ichi beyond design basis accident in March 2011, the Nuclear Regulatory Commission (NRC) issued Order EA-12-049, 'Issuance of Order to Modify Licenses with Regard to Requirements for Mitigation Strategies Beyond-Design-Basis-External-Events'. To outline the process to be used by individual licensees to define and implement site-specific diverse and flexible mitigation strategies (FLEX) that reduce the risks associated with beyond design basis conditions, Nuclear Energy Institute document NEI 12-06, 'Diverse and Flexible Coping Strategies (FLEX) Implementation Guide', was issued. A beyond design basis external event (BDBEE) is postulated to cause an Extended Loss of AC Power (ELAP), which will result in a loss of ventilation which has the potential to impact room habitability and equipment operability. During the ELAP, portable FLEX equipment will be used to achieve and maintain safe shutdown, and only a minimal set of instruments and controls will be available. Given these circumstances, analysis is required to determine the environmental conditions in several vital areas of the Nuclear Power Plant. The BDBEE mitigating strategies require certain room environments to be maintained such that they can support the occupancy of personnel and the functionality of equipment located therein, which is required to support the strategies associated with compliance to NRC Order EA-12-049. Three thermal-hydraulic analyses of vital areas during an extended loss of AC power using the GOTHIC computer code will be presented: 1) Safety-related pump and instrument room transient analysis; 2) Control Room transient analysis; and 3) Auxiliary/Control Building transient analysis. GOTHIC (Generation of Thermal-Hydraulic Information for Containment) is a general purpose thermal-hydraulics software package for the analysis of nuclear power plant containments, confinement buildings, and system components. It is a volume/path/heat sink

7-GeV Advanced Photon Source Instrumentation Initiative conceptual design report

International Nuclear Information System (INIS)

1992-12-01

In this APS Instrumentation Initiative, 2.5-m-long and 5-m-long insertion-device x-ray sources will be built on 9 straight sections of the APS storage ring, and an additional 9 bending-magnet sources will also be put in use. The front ends for these 18 x-ray sources will be built to contain and safeguard access to these bright x-ray beams. In addition, funds will be provided to build state-of-the-art insertion-device beamlines to meet scientific and technological research demands well into the next century. This new initiative will also include four user laboratory modules and a special laboratory designed to meet the x-ray imaging research needs of the users. The Conceptual Design Report (CDR) for the APS Instrumentation Initiative describes the scope of all the above technical and conventional construction and provides a detailed cost and schedule for these activities. According to these plans, this new initiative begins in FY 1994 and ends in FY 1998. The document also describes the preconstruction R ampersand D plans for the Instrumentation Initiative activities and provides the cost estimates for the required R ampersand D

Instruments for reducing the specific fuel consumption of cars

International Nuclear Information System (INIS)

Hammer, S.; Maibach, M.; Marti, P.

2001-01-01

This report for the Swiss Federal Office of Energy (SFOE) presents three possible courses of action that are to be taken to reduce the specific fuel consumption of private cars. The report first examines existing targets and the degree to which they have been met up to now, whereby the situation both in Switzerland and in the European Union is looked at. The report makes a suggestion for a future target scenario and elaborates three possible ways to met these targets: regulations on fuel-consumption, a bonus/malus system and tradable certificates. For each of the proposed instruments, the report examines implementation variants and discusses the means for their implementation. The report presents the best models for each of the implementation-variants on the basis of comparisons and the results of evaluations of their effects. For these chosen variants, the authors present comparisons of their effect on fuel consumption in graphical form and recommend tradable certificates as the best instrument

Pancreatitis Quality of Life Instrument: Development of a new instrument

Directory of Open Access Journals (Sweden)

Wahid Wassef

2014-02-01

Full Text Available Objectives: The goal of this project was to develop the first disease-specific instrument for the evaluation of quality of life in chronic pancreatitis. Methods: Focus groups and interview sessions were conducted, with chronic pancreatitis patients, to identify items felt to impact quality of life which were subsequently formatted into a paper-and-pencil instrument. This instrument was used to conduct an online survey by an expert panel of pancreatologists to evaluate its content validity. Finally, the modified instrument was presented to patients during precognitive testing interviews to evaluate its clarity and appropriateness. Results: In total, 10 patients were enrolled in the focus groups and interview sessions where they identified 50 items. Once redundant items were removed, the 40 remaining items were made into a paper-and-pencil instrument referred to as the Pancreatitis Quality of Life Instrument. Through the processes of content validation and precognitive testing, the number of items in the instrument was reduced to 24. Conclusions: This marks the development of the first disease-specific instrument to evaluate quality of life in chronic pancreatitis. It includes unique features not found in generic instruments (economic factors, stigma, and spiritual factors. Although this marks a giant step forward, psychometric evaluation is still needed prior to its clinical use.

The Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management

International Nuclear Information System (INIS)

Risoluti, P.

2004-01-01

The Joint Convention on the Safety of Spent Fuel Management and the Safety of Radioactive Waste Management (the Joint Convention) is the only legally binding international treaty in the area of radioactive waste management. It was adopted by a Diplomatic Conference in September 1997 and opened for signature on 29 September 1997. The Convention entered into force on 18 June 1998, and to date (September 04) has been signed by 42 States, of which 34 have formally ratified, thus becoming Contracting Parties. The Joint Convention applies to spent fuel and radioactive waste resulting from civilian application. Its principal aim is to achieve and maintain a high degree of safety in their management worldwide. The Convention is an incentive instrument, not designed to ensure fulfillment of obligations through control and sanction, but by a peer pressure. The obligations of the Contracting Parties are mainly based on the international safety standards developed by the IAEA in past decades. The Convention is intended for all countries generating radioactive waste. Therefore it is relevant not only for those using nuclear power, but for any country where application of nuclear energy in medicine, conventional industry and research is currently used. Obligations of Contracting Parties include attending periodic Review Meetings and prepare National Reports for review by the other Contracting Parties. The National Reports should describe how the country is complying with the requirements of the Articles of the Convention. The first such meeting was held at the IAEA headquarters in November 2003. This paper will describe the origin of the Convention, present its content, the expected outcome for the worldwide safety, and the benefits for a country to be part of it

Reproductive autonomy of women and girls under the Convention on the Rights of Persons with Disabilities.

Science.gov (United States)