Innovative technologies of waste recycling with production of high performance products

International Nuclear Information System (INIS)

Gilmanshin, R; Azimov, Yu I; Gilmanshina, S I; Ferenets, A V; Galeeva, A I

2015-01-01

The innovative ways of recycling wastes as a tool for sustainable development are presented in the article. The technology of the production of a composite material based on the rubber fiber composite waste tire industry is presented. The results of experimental use of the products in the real conditions. The comparative characteristics of the composite material rubber fiber composite are given. The production technology of construction and repairing materials on the basis of foamed glass is presented. (paper)

Innovative technologies of waste recycling with production of high performance products

Science.gov (United States)

Gilmanshin, R.; Ferenets, A. V.; Azimov, Yu I.; Galeeva, A. I.; Gilmanshina, S. I.

2015-06-01

The innovative ways of recycling wastes as a tool for sustainable development are presented in the article. The technology of the production of a composite material based on the rubber fiber composite waste tire industry is presented. The results of experimental use of the products in the real conditions. The comparative characteristics of the composite material rubber fiber composite are given. The production technology of construction and repairing materials on the basis of foamed glass is presented.

Innovative Chemical Process for Recycling Thermosets Cured with Recyclamines® by Converting Bio-Epoxy Composites in Reusable Thermoplastic—An LCA Study

Directory of Open Access Journals (Sweden)

Angela D. La Rosa

2018-02-01

Full Text Available An innovative recycling process for thermoset polymer composites developed by Connora Technologies (Hayward, CA, USA was studied. The process efficacy has already been tested, and it is currently working at the plant level. The main aspect investigated in the present paper was the environmental impact by means of the Life Cycle Assessment (LCA method. Because of the need to recycle and recover materials at their end of life, the Connora process creates a great innovation in the market of epoxy composites, as they are notoriously not recyclable. Connora Technologies developed a relatively gentle chemical recycling process that induces the conversion of thermosets into thermoplastics. The LCA demonstrated that low environmental burdens are associated with the process itself and, furthermore, impacts are avoided due to the recovery of the epoxy-composite constituents (fibres and matrix. A carbon fibre (CF epoxy-composite panel was produced through Vacuum Resin Transfer Moulding (VRTM and afterwards treated using the Connora recycling process. The LCA results of both the production and the recycling phases are reported.

Recycling and transmutation of spent fuel as a sustainable option for the nuclear energy development

International Nuclear Information System (INIS)

Maiorino, Jose R.; Moreira, Joao M.L.

2013-01-01

The objective of this paper is to discuss the option of recycling and transmutation of radioactive waste against Once-through Fuel Cycle (OTC) based on uranium feed under the perspective of sustainability. We use a qualitative analysis to compare OTC with closed fuel cycles based on studies already performed such as the Red Impact Project and the comparative study on accelerator driven systems and fast reactors for advanced fuel cycles performed by the Nuclear Energy Agency. The results show that recycling and transmutation fuel cycles are more attractive than the OTC from the point of view of sustainability. The main conclusion is that the decision about the construction of a deep geological repository for spent fuel disposal must be reevaluated. (author)

Understanding the advantages of open innovation practices in corporate venturing in terms of real options

NARCIS (Netherlands)

Vanhaverbeke, W.P.M.; Vrande, van de V.J.A.; Chesbrough, H.

2008-01-01

Part of the advantages of using open innovation (compared to closed innovation) in corporate venturing can be explained by applying the real options approach. Open innovation in risk-laden activities such as corporate venturing has the following advantages: (i) benefits from early involvement in new

ACTINET-I3 Summer School on Analytical Innovation in the field of actinide recycling - Slides of the presentations

International Nuclear Information System (INIS)

Poinssot, Ch.; Nash, K.L.; Puget, P.; Szabo, Z.; Vallet, V.; Berthon, L.; Duhamet, J.; Wipff, G.; Dufreche, J.F.; Walter, P.; Thiebaut, D.; Toulhoat, P.; Aupiais, J.; Amatore, C.

2011-01-01

This conference dealt with 3 main topics: analytical innovation in separation processes (hyphenated techniques, analytical chips,...), actinide recycling (extraction, interfaces, processes,...) and chemistry and thermodynamics of actinides. This document is composed of the slides of the presentations

Waste Management Options for Long-Duration Space Missions: When to Reject, Reuse, or Recycle

Science.gov (United States)

Linne, Diane L.; Palaszewski, Bryan A.; Gokoglu, Suleyman; Gallo, Christopher A.; Balasubramaniam, Ramaswamy; Hegde, Uday G.

2014-01-01

The amount of waste generated on long-duration space missions away from Earth orbit creates the daunting challenge of how to manage the waste through reuse, rejection, or recycle. The option to merely dispose of the solid waste through an airlock to space was studied for both Earth-moon libration point missions and crewed Mars missions. Although the unique dynamic characteristics of an orbit around L2 might allow some discarded waste to intersect the lunar surface before re-impacting the spacecraft, the large amount of waste needed to be managed and potential hazards associated with volatiles recondensing on the spacecraft surfaces make this option problematic. A second option evaluated is to process the waste into useful gases to be either vented to space or used in various propulsion systems. These propellants could then be used to provide the yearly station-keeping needs at an L2 orbit, or if processed into oxygen and methane propellants, could be used to augment science exploration by enabling lunar mini landers to the far side of the moon.

Waste, recycling, and 'Design for Environment': Roles for markets and policy instruments

International Nuclear Information System (INIS)

Calcott, Paul; Walls, Margaret

2005-01-01

Households sometimes have two recycling options. Curbside recycling collections are convenient, but do not provide payment. Alternatively, payment might be available from 'reverse vending machines' or drop-off centers, but some transaction costs would be incurred. We examine policies to encourage efficient product design and recycling in a setting with these two recycling options plus the option of putting recyclables in the trash. We find value in having two parallel recycling options. Constrained optimal outcomes can be attained by combining a 'deposit-refund' with a modest disposal fee. Furthermore, producers should not be permitted to keep deposits, that are not claimed by consumers. (author)

Implementation of a real option in a sustainable supply chain: an empirical study of alkaline battery recycling

Science.gov (United States)

Cucchiella, Federica; D'Adamo, Idiano; Gastaldi, Massimo; Lenny Koh, S. C.

2014-06-01

Green supply chain management (GSCM) has emerged as a key approach for enterprises seeking to become environmentally sustainable. This paper aims to evaluate and describe the advantages of a GSCM approach by analysing practices and performance consequences in the battery recycling sector. It seeks to integrate works in supply chain management (SCM), environmental management, performance management and real option (RO) theory into one framework. In particular, life cycle assessment (LCA) is applied to evaluate the environmental impact of a battery recycling plant project, and life cycle costing (LCC) is applied to evaluate its economic impact. Firms, also understanding the relevance of GSCM, have often avoided applying the green principles because of the elevated costs that such management involved. Such costs could also seem superior to the potential advantages since standard performance measurement systems are internally and business focused; for these reasons, we consider all the possible value deriving also by uncertainty associated to a green project using the RO theory. This work is one of the few and pioneering efforts to investigate GSCM practices in the battery recycling sector.

Environmental decision making for recycling options

DEFF Research Database (Denmark)

Legarth, Jens Brøbech

1997-01-01

A general method for finding new recycling alternatives in the metals producing industry is presented and tested on two printed wire board scrap cases. The underlying idea for the method is that complex scrap should be introduced in the matrix of man-made material flows at recipient points where ...

The Fernald Waste Recycling Program

International Nuclear Information System (INIS)

Motl, G.P.

1993-01-01

Recycling is considered a critical component of the waste disposition strategy at the Fernald Plant. It is estimated that 33 million cubic feet of waste will be generated during the Fernald cleanup. Recycling some portion of this waste will not only conserve natural resources and disposal volume but will, even more significantly, support the preservation of existing disposition options such as off-site disposal or on-site storage. Recognizing the strategic implications of recycling, this paper outlines the criteria used at Fernald to make recycle decisions and highlights several of Fernald's current recycling initiatives

Business Models for Social Innovation of Municipal Solid Waste Recycling Companies: Comparison of Two Business Cases in Thailand and Taiwan

Directory of Open Access Journals (Sweden)

Xiujuan Chen

2018-03-01

Full Text Available The significant increase of municipal solid wastes (e.g., food disposals, biomedical wastes, recyclable materials, etc. is a very important environmental issue around the world. Waste recycling, reduction, and reuse are not only methods to solve environmental problems, but also directions for social innovation for business to create potential social value. This study investigates the business models of two waste recycling companies in Thailand and Taiwan. First, the basic micro and macro environmental factors were analyzed, including the period of firm’s business operations, location of the firm, space for separating and storing recyclable waste and various types of recyclable waste purchasing affecting the firms’ performance in these two economies. Second, different recyclable waste materials, volumes and price strategies between the case companies were compared. Third, this study also investigates the impacts of factors regarding resource characteristics, a firm’s capabilities and an entrepreneur’s abilities to improve a firm’s performance all compose a critical business model. The results showed that there were an increasing number of owners of waste recycling businesses developing and adapting to new business models. Detailed comparisons are reported and discussed in the article to shed light on managerial and policy implications.

External influences on agro-enterprise innovation platforms in Benin, Ghana and Mali – Options for effective responses

NARCIS (Netherlands)

Essegbey, George O.; Sakyi-Dawson, Owuraku; Kossou, Dansou; Ouologuem, Bara; Dembele, Fidiala; Adu-Acheampong, Richard; Jiggins, Janice

2017-01-01

This paper discusses external influences on innovation platforms (IPs) and the options for effective responses. The platforms examined in this paper were conceived as vehicles for facilitating institutional change in support of innovation that benefits smallholders, in selected agro-enterprise

Innovative financing for health: what are the options for South Africa?

Directory of Open Access Journals (Sweden)

Robert J. Fryatt

2012-10-01

Full Text Available The paper assesses the options for additional innovative financing that could be considered in South Africa, covering both raising new funds and linking funds to results. New funds could come from: i the private sector, including the mining and mobile phone industry; ii from voluntary sources, through charities and foundations; iii and through further expanding health (sin levies on products such as tobacco, alcohol and unhealthy food and drinks. As in other countries, South Africa could earmark some of these additional sources for investment in interventions and research to reduce unhealthy behaviors and influence the determinants of health. South Africa could also expand innovative linking of funds to improve overall performance of the health sector, including mitigating the risks for non-state investment and exploring different forms of financial incentives for providers and patients. All such innovations would require rigorous monitoring and evaluation to assess whether intended benefits are achieved and to look for unintended consequences.

Environmental aspects of recycling

International Nuclear Information System (INIS)

Jansma, R.; Van Gemert, F.

2001-01-01

Advanced recycling options were studied. Emphasis was on the production of high-level waste. All other impacts, e.g. emissions, were considered to be of minor importance, since from a technical point of view they can be limited to any desired extent. An objective was to gather data from the industry and to use them in a Life Cycle Analysis (LCA) of several fuel cycle options. It was necessary to complete our data set with literature data. At the end of our project we could benefit from the results of several Expert Working Groups of OECD/NEA. Detailed information was available for the once-through fuel cycle (OFC) and the fuel cycle with mono recycling of MOX. For the other more advanced fuel cycle options information was of a more qualitative nature. The established set of data was sufficient to conduct a streamlined LCA with focus on waste production for final disposal. Some remarks should be made before comparing the various fuel cycle options studied. The first relates to plutonium that contributes to more than 90% of the radiotoxicity of the spent fuel for more than 1000 centuries. Large concern for transmutation of minor actinides will disproportional if plutonium itself is not eliminated. The second remark is that the fission products contribute potentially very little to the radiotoxicity especially when some long-lived radionuclides after separation are imprisoned in stable matrices to prevent them to be carried by underground water. From all nuclear fuel cycles considered, the MIX cycle in LWRs, with recycling of plutonium and minor actinides has the lowest minor actinides production (0.018 kg/TW e h) and the plutonium production is also quite low (0.06 kg/TW e h). The MIX cycle without minor actinides recycling performs a little better with respect to plutonium production (0.04 kg/TW e h) but has a relatively high minor actinides production (8.7 kg/TW e h). Another conclusion is that burning of minor actinides in fast reactors (MA 0.28 kg/TW e h, Pu 0

School Recycling Programs: A Handbook for Educators.

Science.gov (United States)

Environmental Protection Agency, Washington, DC.

This brochure describes some of the many recycling program options that schools can implement in their communities. It focuses on implementing actual recycling projects as a way of teaching the importance and benefits of recycling. The text examines the solid waste crisis and why Americans cannot continue to possess a disposable mentality. It…

Demonstration of innovative partitioning processes for minor actinide recycling from high active waste solutions

International Nuclear Information System (INIS)

Modolo, G.; Wilden, A.; Geist, A.; Malmbeck, R.; Taylor, R.

2014-01-01

The recycling of the minor actinides (MA) using the Partitioning and Transmutation strategy (P and T) could contribute significantly to reducing the volume of high level waste in a geological repository and to decreasing the waste's longterm hazards originating from the long half-life of the actinides. Several extraction processes have been developed worldwide for the separation and recovery of MA from highly active raffinates (HAR, e.g. the PUREX raffinate). A multi-cycle separation strategy has been developed within the framework of European collaborative projects. The multi-cycle processes, on the one hand, make use of different extractants for every single process. Within the recent FP7 European research project ACSEPT (Actinide reCycling by SEParation and Transmutation), the development of new innovative separation processes with a reduced number of cycles was envisaged. In the so-called 'innovative SANEX' concept, the trivalent actinides and lanthanides are co-extracted from the PUREX raffinate by a DIAMEX like process (e.g. TODGA). Then, the loaded solvent is subjected to several stripping steps. The first one concerns selectively stripping the actinides(III) with selective water-soluble ligands (SO3-Ph-BTB), followed by the subsequent stripping of trivalent lanthanides. A more challenging route studied also within our laboratories is the direct actinide(III) separation from a PUREX-type raffinate using a mixture of CyMe 4 BTBP and TODGA as extractants, the so-called One cycle SANEX process. A new approach, which was also studied within the ACSEPT project, is the GANEX (Grouped ActiNide EXtraction) concept addressing the simultaneous partitioning of all transuranium (TRU) elements for their homogeneous recycling in advanced generation IV reactor systems. Bulk uranium is removed in the GANEX 1st cycle, e.g. using a monoamide extractant and the GANEX 2nd cycle then separates the TRU. A solvent composed of TODGA + DMDOHEMA in kerosene has been shown to

Hanford recycling

Energy Technology Data Exchange (ETDEWEB)

Leonard, I.M.

1996-09-01

This paper is a study of the past and present recycling efforts on the Hanford site and options for future improvements in the recycling program. Until 1996, recycling goals were voluntarily set by the waste generators: this year, DOE has imposed goals for all its sites to accomplish by 1999. Hanford is presently meeting the voluntary site goals, but may not be able to meet all the new DOE goals without changes to the program. Most of these new DOE goals are recycling goals: * Reduce the generation of radioactive (low-level) waste from routine operations 50 percent through source reduction and recycling. * Reduce the generation of low-level mixed waste from routine operations 50 percent through source reduction and recycling. * Reduce the generation of hazardous waste from routine operations 50 percent through source reduction and recycling. * Recycle 33 percent of the sanitary waste from all operations. * Increase affirmative procurement of EPA-designated recycled items to 100 percent. The Hanford recycling program has made great strides-there has been a 98 percent increase in the amount of paper recycled since its inception in 1990. Hanford recycles paper, chemicals cardboard, tires, oil, batteries, rags, lead weights, fluorescent tubes, aerosol products, concrete, office furniture, computer software, drums, toner cartridges, and scrap metal. Many other items are recycled or reused by individual groups on a one time basis without a formal contract. Several contracts are closed-loop contracts which involve all parts of the recycle loop. Considerable savings are generated from recycling, and much more is possible with increased attention and improvements to this program. General methods for improving the recycling program to ensure that the new goals can be met are: a Contract and financial changes 0 Tracking database and methods improvements 0 Expanded recycling efforts. Specifically, the Hanford recycling program would be improved by: 0 Establishing one overall

Paper waste - Recycling, incineration or landfilling?

DEFF Research Database (Denmark)

Villanueva, Alejandro; Wenzel, Henrik

2007-01-01

comparisons of different management options for waste paper. Despite claims of inconsistency, the LCAs reviewed illustrate the environmental benefits in recycling over incineration or landfill options, for paper and cardboard waste. This broad consensus was found despite differences in geographic location....... Such message has implications for current policy formulation on material recycling and disposal in the EU. Secondly, to identify key methodological issues of paper waste management LCAs, and enlighten the influence of such issues on the conclusions of the LCA studies. Thirdly, in light of the analysis made...... and definitions of the paper recycling/disposal systems studied. A systematic exploration of the LCA studies showed, however, important methodological pitfalls and sources of error, mainly concerning differences in the definition of the system boundaries. Fifteen key assumptions were identified that cover...

Recycling light metals : Optimal thermal de-coating

NARCIS (Netherlands)

Kvithyld, A.; Meskers, C.E.M.; Gaal, S.; Reuter, M.

2008-01-01

Thermal de-coating of painted and lacquered scrap is one of the new innovations developed for aluminum recycling. If implemented in all recycling and optimized as suggested in this article, recovery would be improved with considerable economic impact. Generally, contaminated scrap is difficult to

PRN 94-2: Recycling Empty Aerosol Pesticide Containers

Science.gov (United States)

This notice offers registrants use of an optional label statement permitting recycling as an alternative to instructions to dispose of aerosol pesticide containers. Registrants may add a label reference to recycling the empty aerosol pesticide container.

Performance evaluation of subgrade stabilization with recycled materials.

Science.gov (United States)

2016-02-29

Due to rising costs of good quality acceptable materials for remove/replace options and traditional : subgrade stabilization materials, MDOT is in need to identify potential recycled materials to treat : unacceptable subgrade soils. Use of recycled m...

Radioactive metals disposal and recycling impact modelling

International Nuclear Information System (INIS)

Kemp, N.W.; Lunn, R.J.; Belton, V.; Kockar, I.

2014-01-01

Screening life cycle assessment models developed to investigate hypothetical disposal and recycling options for the Windscale Advanced Gas-cooled Reactor heat exchangers were used to generate more complex models addressing the main UK radioactive metals inventory. Both studies show there are significant environmental advantages in the metals recycling promoted by the current low level waste disposal policies, strategies and plans. Financial benefits from current metals treatment options are supported and offer even greater benefits when applied to the UK radioactive metals inventory as a whole. (authors)

EVALUATION OF RECYCLED PLASTIC LUMBER FOR MARINE APPLICATIONS

Science.gov (United States)

This report presents an evaluation of the recycled plastic materials (RPM) produced by California Recycling Company (CRC). This evaluation is performed under the Municipal Waste Innovative Technology Evaluation (MITE) Program of the U.S. EPA, Risk Reduction Engineering Laboratory...

Economical aspects of multiple plutonium and uranium recycling in VVER reactors

Energy Technology Data Exchange (ETDEWEB)

Alekseev, P.N.; Bobrov, E.A.; Dudnikov, A.A.; Teplov, P.S. [National Research Centre ' Kurchatov Institute' , Moscow (Russian Federation)

2016-09-15

The basic strategy of Russian Nuclear Energy development is the formation of the closed fuel cycle based on fast breeder and thermal reactors, as well as the solution of problems of spent nuclear fuel accumulation and availability of resources. Three options of multiple Pu and U recycling in VVER reactors are considered in this work. Comparison of MOX and REMIX fuel recycling approaches for the closed fuel cycle involving thermal reactors is presented. REMIX fuel is supposed to be fabricated from non-separated mixture of uranium and plutonium obtained in spent fuel reprocessing with further makeup by enriched U. These options make it possible to recycle several times the total amount of Pu and U obtained from spent fuel. The main difference is the full or partial fuel loading of the core by assemblies with recycled Pu. The third option presents the concept of heterogeneous arrangement of fuel pins made of enriched uranium and MOX in one fuel assembly. It should be noted that fabrication of all fuel assemblies with Pu requires the use of expensive manufacturing technology. These three options of core loading can be balanced with respect to maximum Pu and U involvement in the fuel cycle. Various physical and economical aspects of Pu and U multiple recycling for selected options are considered in this work.

Proceedings of waste stream minimization and utilization innovative concepts: An experimental technology exchange. Volume 1, Industrial solid waste processing municipal waste reduction/recycling

Energy Technology Data Exchange (ETDEWEB)

Lee, V.E. [ed.; Watts, R.L.

1993-04-01

This two-volume proceedings summarizes the results of fifteen innovations that were funded through the US Department of Energy`s Innovative Concept Program. The fifteen innovations were presented at the sixth Innovative Concepts Fair, held in Austin, Texas, on April 22--23, 1993. The concepts in this year`s fair address innovations that can substantially reduce or use waste streams. Each paper describes the need for the proposed concept, the concept being proposed, and the concept`s economics and market potential, key experimental results, and future development needs. The papers are divided into two volumes: Volume 1 addresses innovations for industrial solid waste processing and municipal waste reduction/recycling, and Volume 2 addresses industrial liquid waste processing and industrial gaseous waste processing. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

Recycling as an option of used nuclear fuel management strategy for Europe

International Nuclear Information System (INIS)

Chiguer, M.; Casabianca, J.L.; Gros, J.P.

2010-01-01

As soon as the civil nuclear power age got underway, it became unthinkable to imagine generating nuclear electricity without recycling nuclear materials. In every country where this form of energy was being developed, construction programs involved not only power plants, but also fuel cycle facilities, notably dedicated to recovering and recycling nuclear material. Today, the nuclear renaissance coupled with growing concerns about energy security and public acceptance will provide a trigger for European nuclear countries to look back on three decades of Recycling used nuclear fuel excellent track record. In addition, back-end policy is more and more one of the major topics that nuclear countries and utilities have to face when managing existing as well as a new nuclear power plant. 'What will be done with the used fuel' is a key question, especially in terms of public acceptance. Countries that have previously postponed this topic now have to rethink the best solution for complete sustainable nuclear power. With several decades of experience and excellent feedback recycling has reached a maturity throughout all its supply chain and therefore constitutes the best response. The outcome is outstanding performance in reactors of recycled fuels and a robust, economical and optimized solution to ultimate waste management, in other words: - Recycling allows to significantly reduce the volume and toxicity of the ultimate waste to be interim stored and disposed of while enhancing proliferation resistance, - Recycling features competitive and predictable economics, - Recycling Used Nuclear Fuel supports the sustainable development of nuclear power allowing mitigating supply risks. All this helps to increase public support towards nuclear energy and insure the sustainable development of nuclear energy here and now. (authors)

Logistics Mode and Network Planning for Recycle of Crop Straw Resources

OpenAIRE

Zhou, Lingyun; Gu, Weidong; Zhang, Qing

2013-01-01

To realize the straw biomass industrialized development, it should speed up building crop straw resource recycle logistics network, increasing straw recycle efficiency, and reducing straw utilization cost. On the basis of studying straw recycle process, this paper presents innovative concept and property of straw recycle logistics network, analyses design thinking of straw recycle logistics network, and works out straw recycle logistics mode and network topological structure. Finally, it come...

Uranium Resource Availability Analysis of Four Nuclear Fuel Cycle Options

International Nuclear Information System (INIS)

Youn, S. R.; Lee, S. H.; Jeong, M. S.; Kim, S. K.; Ko, W. I.

2013-01-01

Making the national policy regarding nuclear fuel cycle option, the policy should be established in ways that nuclear power generation can be maintained through the evaluation on the basis of the following aspects. To establish the national policy regarding nuclear fuel cycle option, that must begin with identification of a fuel cycle option that can be best suited for the country, and the evaluation work for that should be proceeded. Like all the policy decision, however, a certain nuclear fuel cycle option cannot be superior in all aspects of sustain ability, environment-friendliness, proliferation-resistance, economics, technologies, which make the comparison of the fuel cycle options very complicated. For such a purpose, this paper set up four different fuel cycle of nuclear power generation considering 2nd Comprehensive Nuclear Energy Promotion Plan(CNEPP), and analyzed material flow and features in steady state of all four of the fuel cycle options. As a result of an analysis on material flow of each nuclear fuel cycle, it was analyzed that Pyro-SFR recycling is most effective on U resource availability among four fuel cycle option. As shown in Figure 3, OT cycle required the most amount of U and Pyro-SFR recycle consumed the least amount of U. DUPIC recycling, PWR-MOX recycling, and Pyro-SFR recycling fuel cycle appeared to consumed 8.2%, 12.4%, 39.6% decreased amount of uranium respectively compared to OT cycle. Considering spent fuel can be recycled as potential energy resources, U and TRU taken up to be 96% is efficiently used. That is, application period of limited uranium natural resources can be extended, and it brings a great influence on stable use of nuclear energy

NPS transportation innovative finance options

Science.gov (United States)

2013-05-01

This paper provides a summary of innovative transportation finance techniques and discusses their applicability to the National Park Service (NPS). The primary finding of this analysis is that while NPS is engaging in innovative finance techniques su...

BPEO/BPM in recycling of low level waste metal in the UK - 16210

International Nuclear Information System (INIS)

Dodd, Kevin; Robinson, Joe; Lindberg, Maria

2009-01-01

Best Practicable Environmental Option (BPEO) and Best Practicable Means (BPM) are concepts well established in the nuclear industry to help guide and inform waste management decision making. The recycling of contaminated metal waste in the UK is not well established, with the majority of waste disposed of at the Low Level Waste Repository (LLWR) at Drigg. This paper presents an overview of the Strategic BPEO study completed by Studsvik examining the options for low level metal waste management and a subsequent BPM study completed in support of a proposed metals recycling service. The environmental benefits of recycling metals overseas is further examined through the application of life cycle analysis to the metals recycling process. The methodologies used for both studies are discussed and the findings of these studies presented. These indicate that recycling contaminated metal is the preferred option, using overseas facilities until UK facilities are available. The BPM for metals recycling is discussed in detail and indicates that a tool box for processing metal waste is required to ensure BPM is applied on a case by case basis. This is supported by effective management of waste transport and waste acceptance criteria. Whilst the transport of contaminated metal overseas for treatment adds to the environmental burden of metals recycling, this when compared with the production of virgin metal, is shown to remain beneficial. The results of the Studsvik studies demonstrate the benefits of recycling metals, the options available for such a service and challenges that remain. (authors)

Recycling issues facing target and RTL materials of inertial fusion designs

International Nuclear Information System (INIS)

El-Guebaly, L.; Wilson, P.; Sawan, M.; Henderson, D.; Varuttamaseni, A.

2005-01-01

Designers of heavy ion (HI) and Z-pinch inertial fusion power plants have explored the potential of recycling the target and recyclable transmission line (RTL) materials as an alternate option to disposal in a geological repository. This work represents the first time a comprehensive recycling assessment was performed on both machines with an exact pulse history. Our results offer two divergent conclusions on the recycling issue. For the HI concept, target recycling is not a 'must' requirement and the preferred option is the one-shot use scenario as target materials represent a small waste stream, less than 1% of the total nuclear island waste. We recommend using low-cost hohlraum materials once-through and then disposing of them instead of recycling expensive materials such as Au and Gd. On the contrary, RTL recycling is a 'must' requirement for the Z-pinch concept in order to minimize the RTL inventory and enhance the economics. The RTLs meet the low level waste and recycling dose requirements with a wide margin when recycled for the entire plant life even without a cooling period. While recycling offers advantages to the Z-pinch system, it adds complexity and cost to the HI designs

Shared Urban Greywater Recycling Systems: Water Resource Savings and Economic Investment

Directory of Open Access Journals (Sweden)

Dexter V.L. Hunt

2013-07-01

Full Text Available The water industry is becoming increasingly aware of the risks associated with urban supplies not meeting demands by 2050. Greywater (GW recycling for non-potable uses (e.g., urinal and toilet flushing provides an urban water management strategy to help alleviate this risk by reducing main water demands. This paper proposes an innovative cross connected system that collects GW from residential buildings and recycles it for toilet/urinal flushing in both residential and office buildings. The capital cost (CAPEX, operational cost (OPEX and water saving potential are calculated for individual and shared residential and office buildings in an urban mixed-use regeneration area in the UK, assuming two different treatment processes; a membrane bioreactor (MBR and a vertical flow constructed wetland (VFCW. The Net Present Value (NPV method was used to compare the financial performance of each considered scenario, from where it was found that a shared GW recycling system (MBR was the most economically viable option. The sensitivity of this financial model was assessed, considering four parameters (i.e., water supply and sewerage charges, discount rate(s, service life and improved technological efficiency, e.g., low flush toilets, low shower heads, etc., from where it was found that shared GW systems performed best in the long-term.

The option value of innovative treatments for non-small cell lung cancer and renal cell carcinoma.

Science.gov (United States)

Thornton Snider, Julia; Batt, Katharine; Wu, Yanyu; Tebeka, Mahlet Gizaw; Seabury, Seth

2017-10-01

To develop a model of the option value a therapy provides by enabling patients to live to see subsequent innovations and to apply the model to the case of nivolumab in renal cell carcinoma (RCC) and non-small cell lung cancer (NSCLC). A model of the option value of nivolumab in RCC and NSCLC was developed and estimated. Data from the Surveillance, Epidemiology, and End Results (SEER) cancer registry and published clinical trial results were used to estimate survival curves for metastatic cancer patients with RCC, squamous NSCLC, or nonsquamous NSCLC. To estimate the conventional value of nivolumab, survival with the pre-nivolumab standard of care was compared with survival with nivolumab assuming no future innovation. To estimate the option value of nivolumab, long-term survival trends in RCC and squamous and nonsquamous NSCLC were measured in SEER to forecast mortality improvements that nivolumab patients may live to see. Compared with the previous standard of care, nivolumab extended life expectancy by 6.3 months in RCC, 7.5 months in squamous NSCLC, and 4.5 months in nonsquamous NSCLC, according to conventional methods. Accounting for expected future mortality trends, nivolumab patients are likely to gain an additional 1.2 months in RCC, 0.4 months in squamous NSCLC, and 0.5 months in nonsquamous NSCLC. These option values correspond to 18%, 5%, and 10% of the conventional value of nivolumab, respectively. Option value is important when valuing therapies like nivolumab that extend life in a rapidly evolving area of care.

Considerations in recycling contaminated scrap metal and rubble

International Nuclear Information System (INIS)

Kluk, A.F.; Hocking, E.K.

1992-01-01

Management options for the Department of Energy's increasing amounts of contaminated scrap metal and rubble include reuse as is, disposal, and recycling. Recycling, with its promise of resource recovery, virgin materials conservation, and land disposal minimization, emerges as a preferred management technique. Implementing a cost effective recycling program requires resolution of several issues including: establishing release limits for contaminants, controlling use of recycled materials creating effective public communication programs; developing economical, reliable assay technologies; managing secondary waste streams, expanding availability of unrestricted markets; and solving conflicting legal considerations

Design of an innovative, ecological portable waste compressor for in-house recycling of paper, plastic and metal packaging waste.

Science.gov (United States)

Xevgenos, D; Athanasopoulos, N; Kostazos, P K; Manolakos, D E; Moustakas, K; Malamis, D; Loizidou, M

2015-05-01

Waste management in Greece relies heavily on unsustainable waste practices (mainly landfills and in certain cases uncontrolled dumping of untreated waste). Even though major improvements have been achieved in the recycling of municipal solid waste during recent years, there are some barriers that hinder the achievement of high recycling rates. Source separation of municipal solid waste has been recognised as a promising solution to produce high-quality recycled materials that can be easily directed to secondary materials markets. This article presents an innovative miniature waste separator/compressor that has been designed and developed for the source separation of municipal solid waste at a household level. The design of the system is in line with the Waste Framework Directive (2008/98/EC), since it allows for the separate collection (and compression) of municipal solid waste, namely: plastic (polyethylene terephthalate and high-density polyethylene), paper (cardboard and Tetrapak) and metal (aluminium and tin cans). It has been designed through the use of suitable software tools (LS-DYNA, INVENTROR and COMSOL). The results from the simulations, as well as the whole design process and philosophy, are discussed in this article. © The Author(s) 2015.

Safeguards and nonproliferation aspects of a dry fuel recycling technology

International Nuclear Information System (INIS)

Pillay, K.K.S.

1993-01-01

Los Alamos National Laboratory undertook an independent assessment of the proliferation potentials and safeguardability of a dry fuel recycling technology, whereby spent pressurized-water reactor (PWR) fuels are used to fuel canadian deuterium uranium (CANDU) reactors. Objectives of this study included (1) the evaluation of presently available technologies that may be useful to safeguard technology options for dry fuel recycling (2) and identification of near-term and long-term research needs to develop process-specific safeguards requirements. The primary conclusion of this assessment is that like all other fuel cycle alternatives proposed in the past, the dry fuel recycle entails prolfferation risks and that there are no absolute technical fixes to eliminate such risks. This study further concludes that the proliferation risks of dry fuel recycling options are relatively minimal and presently known safeguards systems and technologies can be modified and/or adapted to meet the requirements of safeguarding such fuel recycle facilities

Textiles and clothing sustainability recycled and upcycled textiles and fashion

CERN Document Server

2017-01-01

This book discusses in detail the concepts of recycling and upcycling and their implications for the textiles and fashion sector. In addition to the theoretical concepts, the book also presents various options for recycling and upcycling in textiles and fashion. Although recycling is a much-developed and widely used concept, upcycling is also gaining popularity in the sector.

Different possible scenarios for plutonium recycling in PWRs

International Nuclear Information System (INIS)

Grouiller, J.P.; Doriath, J.Y.; Vasile, A.; Zaetta, A.; Guillet, J.L.; Greneche, D.

2001-01-01

Stabilisation of the Pu inventory in the electronuclear fleet (cycle reactors and facilities) is achieved through multi-recycling which can be carried out in current PWR through rod design or standard assembly composition modifications. The aim of this paper is to present the range of technical solutions which may be envisioned in current PWRs from a strictly physical point of view. It aims to give a preview of scientific feasibility of the various options bearing in mind that technological feasibility and, to an even greater extent, economic assessment would be premature at this moment and that industrialists would be responsible for this. Currently once through cycling of Plutonium is carried out in pressurised water reactors (PWR) in a MOX assembly partially loaded core. These current reactors (900 MW), initially licensed to use Uranium enriched UOX fuel, were therefore slightly adapted to accept plutonium. For a more efficient and less limiting use of plutonium in a PWR several fuel concepts are currently being examined. The objective of these innovative fuel concepts is to facilitate core management in a Pu multi-recycling strategy, to increase fuel burn up performances, keeping safety margins which has to be the same of to current UOX fuel loaded PWR reactors. (author)

Development of an innovative PWR for low cost fuel recycle and waste reduction

International Nuclear Information System (INIS)

Kanagawa, Takashi; Onoue, Masaaki

2001-01-01

In order to bear long-term and stable energy supply, it is important for nuclear power generation to realize establishment of energy security controlling dependence on natural resources and reduction of long-life radioactive wastes such as minor actinide elements (MA) and so on. For this, establishment of fast breeder reproducible on its fuel and of fuel recycling is essential and construction of the fuel recycling capable of repeatedly recycling of plutonium (Pu) and MA with low cost is required. Here were proposed a fuel recycling system combining recycling type PWR with advanced recycling system under development for Na cooling fast breeder reactor as a candidate filling such conditions, to show its characteristics and effects after its introduction. By this system, some facilities to realize flexible and low cost fuel recycling, to reduce longer-life radioactive wastes due to recycling burning of Pu and MA, and to realize an electric power supplying system independent on natural resources due to fuel breeding feature, were shown. (G.K.)

Economic potential of fuel recycling options: A lifecycle cost analysis of future nuclear system transition in China

International Nuclear Information System (INIS)

Gao, Ruxing; Choi, Sungyeol; Il Ko, Won; Kim, Sungki

2017-01-01

In today's profit-driven market, how best to pursue advanced nuclear fuel cycle technologies while maintaining the cost competitiveness of nuclear electricity is of crucial importance to determine the implementation of spent fuel reprocessing and recycling in China. In this study, a comprehensive techno-economic analysis is undertaken to evaluate the economic feasibility of ongoing national projects and the technical compatibility with China's future fuel cycle transition. We investigated the dynamic impacts of technical and economic uncertainties in the lifecycle of a nuclear system. The electricity generation costs associated with four potential fuel cycle transition scenarios were simulated by probabilistic and deterministic approaches and then compared in detail. The results showed that the total cost of a once-through system is lowest compared those of other advanced systems involving reprocessing and recycling. However, thanks to the consequential uncertainties caused by the further progress toward technology maturity, the economic potential of fuel recycling options was proven through a probabilistic uncertainty analysis. Furthermore, it is recommended that a compulsory executive of closed fuel cycle policy would pose some investment risk in the near term, though the execution of a series of R&D initiatives with a flexible roadmap would be valuable in the long run. - Highlights: • Real-time economic performance of the four scenarios of China's nuclear fuel cycle system transition until 2100. • Systematic assessments of techno-economic feasibility for ongoing national reprocessing projects. • Investigation the cost impact on nuclear electricity generation caused by uncertainties through probabilistic analysis. • Recommendation for sustainable implementation of fuel cycle R&D initiative ingrate with flexible roadmap in the long run.

A multi-criteria decision analysis assessment of waste paper management options

Energy Technology Data Exchange (ETDEWEB)

Hanan, Deirdre [Department of Design, Development, Environment and Materials, The Open University, Walton Hall, Milton Keynes, MK7 6AA (United Kingdom); Burnley, Stephen, E-mail: s.j.burnley@open.ac.uk [Department of Design, Development, Environment and Materials, The Open University, Walton Hall, Milton Keynes, MK7 6AA (United Kingdom); Cooke, David [Department of Design, Development, Environment and Materials, The Open University, Walton Hall, Milton Keynes, MK7 6AA (United Kingdom)

2013-03-15

Highlights: ► Isolated communities have particular problems in terms of waste management. ► An MCDA tool allowed a group of non-experts to evaluate waste management options. ► The group preferred local waste management solutions to export to the mainland. ► Gasification of paper was the preferred option followed by recycling. ► The group concluded that they could be involved in the decision making process. - Abstract: The use of Multi-criteria Decision Analysis (MCDA) was investigated in an exercise using a panel of local residents and stakeholders to assess the options for managing waste paper on the Isle of Wight. Seven recycling, recovery and disposal options were considered by the panel who evaluated each option against seven environmental, financial and social criteria. The panel preferred options where the waste was managed on the island with gasification and recycling achieving the highest scores. Exporting the waste to the English mainland for incineration or landfill proved to be the least preferred options. This research has demonstrated that MCDA is an effective way of involving community groups in waste management decision making.

A multi-criteria decision analysis assessment of waste paper management options

International Nuclear Information System (INIS)

Hanan, Deirdre; Burnley, Stephen; Cooke, David

2013-01-01

Highlights: ► Isolated communities have particular problems in terms of waste management. ► An MCDA tool allowed a group of non-experts to evaluate waste management options. ► The group preferred local waste management solutions to export to the mainland. ► Gasification of paper was the preferred option followed by recycling. ► The group concluded that they could be involved in the decision making process. - Abstract: The use of Multi-criteria Decision Analysis (MCDA) was investigated in an exercise using a panel of local residents and stakeholders to assess the options for managing waste paper on the Isle of Wight. Seven recycling, recovery and disposal options were considered by the panel who evaluated each option against seven environmental, financial and social criteria. The panel preferred options where the waste was managed on the island with gasification and recycling achieving the highest scores. Exporting the waste to the English mainland for incineration or landfill proved to be the least preferred options. This research has demonstrated that MCDA is an effective way of involving community groups in waste management decision making

Energy Return on Investment from Recycling Nuclear Fuel

International Nuclear Information System (INIS)

2011-01-01

This report presents an evaluation of the Energy Return on Investment (EROI) from recycling an initial batch of 800 t/y of used nuclear fuel (UNF) through a Recycle Center under a number of different fuel cycle scenarios. The study assumed that apart from the original 800 t of UNF only depleted uranium was available as a feed. Therefore for each subsequent scenario only fuel that was derived from the previous fuel cycle scenario was considered. The scenarios represent a good cross section of the options available and the results contained in this paper and associated appendices will allow for other fuel cycle options to be considered.

Recycling ampersand incineration: Evaluating the choices

International Nuclear Information System (INIS)

Denison, R.A.; Ruston, J.

1993-01-01

Conflicts between proponents of municipal solid waste incineration and advocates of recycling have escalated with efforts to reduce the volume of waste that ends up in landfills. Central to this debate is competition for materials that are both combustible and recyclable. Environmental and economic concerns also play a major role. This book, produced by the Environmental Defense Fund, compares recycling and incineration. It is intended for 'citizens, government officials, and business people who want to help resolve the solid-waste crisis.' The book is divided into three parts: recycling and incineration; health and environmental risk of incineration; and planning, public participation, and environmental review requirements. The book does an excellent job of discussing the benefits of recycling and the pitfalls of incineration. It provides helpful information for identifying questions that should be raised about incineration, but it does not raise similar queries about recycling. There is much worthwhile information here, but the book would be more useful if it identified critical issues for all waste reduction and management options

The Relevance of Metal Recycling for Nuclear Industry Decommissioning Programmes

Energy Technology Data Exchange (ETDEWEB)

O' Sullivan, P.J., E-mail: nea@nea.fr [OECD Nuclear Energy Agency, Paris (France)

2011-07-15

The large amount of scrap metal arising from the decommissioning of nuclear facilities may present significant problems in the event that the facility owners seek to implement a management strategy based largely or fully on disposal in dedicated disposal facilities. Depending on whether disposal facilities currently exist or need to be developed, this option can be very expensive. Also, public reluctance to accept the expansion of existing disposal facilities, or the siting of new ones, mean that the disposal option should be used only after a wide consideration of all available management options. A comparison of health, environmental and socio-economic impacts of the recycling of lightly contaminated scrap metal, as compared with equivalent impacts associated with the production of replacement material, suggests that recycling has significant overall advantages. With present-day technologies, a large proportion of the metal waste from decommissioning can be decontaminated to clearance levels because most of the contamination is on or near the surface of the metal. In purely economic terms, it makes little sense for lightly contaminated scrap metal from decommissioning, which tends to be of high quality, to be removed from the supply chain and replaced with metal from newly-mined ore. In many countries, the metal recycling industry remains reluctant to accept metal from decommissioning. In Germany, the recycling industry and the decommissioning industry have worked together to develop an approach whereby such material is accepted for melting and the recycled material and is then used for certain defined end uses. Sweden also uses dedicated melting facilities for the recycling of metal from the nuclear industry. Following this approach, the needs of the decommissioning industry are being met in a way that also addresses the needs of the recycling industry. (author)

Compositional data analysis of household waste recycling centres in Denmark

DEFF Research Database (Denmark)

Edjabou, Maklawe Essonanawe; Martín-Fernández, J. A.; Boldrin, Alessio

of these projects on the recycling rates does not exist. Thus, compositional data analysis technique was applied to analyze consistently waste data. Based on the waste composition obtained from a recycling center in Denmark, we analyzed the composition of waste treatment and disposal options. Zero and non......-zero pattern was used to describe historical changes in the definition and components of waste fractions. Variation array was applied to determine the relationship between waste treatment and disposal options. As a result, compositional data analysis technique enables to analyze waste data regardless...

A tale of five cities: Using recycling frameworks to analyse inclusive recycling performance.

Science.gov (United States)

Scheinberg, Anne; Simpson, Michael

2015-11-01

'Recycling' is a source of much confusion, particularly when comparing solid waste systems in high-income countries with those in low- and middle-income countries. Few analysts can explain why the performance and structure of recycling appears to be so different in rich countries from poor ones, nor why well-meaning efforts to implement recycling so often fail. The analysis of policy drivers, and the Integrated Sustainable Waste Management (ISWM) framework, come close to an explanation.This article builds on these earlier works, focusing in on five cities profiled in the 2010 UN-Habitat publication (Scheinberg A, Wilson DC and Rodic L (2010) Solid Waste Management in the World's Cities. UN-Habitat's Third Global Report on the State of Water and Sanitation in the World's Cities. Newcastle-on-Tyne, UK: Earthscan Publications). Data from these cities and others provides the basis for developing a new tool to analyse inclusive recycling performance. The points of departure are the institutional and economic relationships between the service chain, the public obligation to remove waste, pollution, and other forms of disvalue, and the value chain, a system of private enterprises trading valuable materials and providing markets for recyclables. The methodological innovation is to use flows of materials and money as indicators of institutional relationships, and is an extension of process flow diagramming.The authors are using the term 'recycling framework analysis' to describe this new form of institutional analysis. The diagrams increase our understanding of the factors that contribute to high-performance inclusive recycling. By focusing on institutional relationships, the article seeks to improve analysis, planning, and ultimately, outcomes, of recycling interventions. © The Author(s) 2015.

A multi-criteria decision analysis assessment of waste paper management options.

Science.gov (United States)

Hanan, Deirdre; Burnley, Stephen; Cooke, David

2013-03-01

The use of Multi-criteria Decision Analysis (MCDA) was investigated in an exercise using a panel of local residents and stakeholders to assess the options for managing waste paper on the Isle of Wight. Seven recycling, recovery and disposal options were considered by the panel who evaluated each option against seven environmental, financial and social criteria. The panel preferred options where the waste was managed on the island with gasification and recycling achieving the highest scores. Exporting the waste to the English mainland for incineration or landfill proved to be the least preferred options. This research has demonstrated that MCDA is an effective way of involving community groups in waste management decision making. Copyright © 2012 Elsevier Ltd. All rights reserved.

Financial Engineering With Options and Its Implementation for Issuing of New Financial Innovations

Directory of Open Access Journals (Sweden)

Martina Bobriková

2017-09-01

Full Text Available Purpose: The purpose of the paper is to focus on innovative structured products − investment certificates. The paper shows the creation techniques of a new discount basket certificate using two-asset correlation options, which play the central role in financial engineering. The possibilities of investment using given certificates are investigated for potential investors. Methodology: Methodology of the paper is based on European style two-asset correlation options in analytical expression whose payoff is based on two underlying assets with two strike prices. Due to the lack of real-traded two asset correlation option data, own calculations of option premiums are processed in statistical program R. Also, the pricing of the new discount basket certificate is examines. Approach: Theoretical value of the new discount basket certificate with different levels of its parameters on the stocks Facebook and Google is obtained and it is performed the analysis of the profitability for to the investor at the maturity date. Also, there is showed which parameters the investor should pay attention when deciding to invest into the given investment certificate. Findings: Specific characteristics of each proposed certificate are pointed out and compared to each other with conclusion that every certificate can be the most profitable in specific price development of the underlying assets, but not in every price development. Ideas on how this certificate can be part of a personal investment portfolio are also presented.

Evaluation of radioactive scrap metal recycling

International Nuclear Information System (INIS)

Nieves, L.A.; Chen, S.Y.; Kohout, E.J.; Nabelssi, B.; Tilbrook, R.W.; Wilson, S.E.

1995-12-01

This report evaluates the human health risks and environmental and socio-political impacts of options for recycling radioactive scrap metal (RSM) or disposing of and replacing it. Argonne National Laboratory (ANL) is assisting the US Department of Energy (DOE), Office of Environmental Restoration and Waste Management, Oak Ridge Programs Division, in assessing the implications of RSM management alternatives. This study is intended to support the DOE contribution to a study of metal recycling being conducted by the Task Group on Recycling and Reuse of the Organization for Economic Cooperation and Development. The focus is on evaluating the justification for the practice of recycling RSM, and the case of iron and steel scrap is used as an example in assessing the impacts. To conduct the evaluation, a considerable set of data was compiled and developed. Much of this information is included in this document to provide a source book of information

Evaluation of radioactive scrap metal recycling

Energy Technology Data Exchange (ETDEWEB)

Nieves, L.A.; Chen, S.Y.; Kohout, E.J.; Nabelssi, B.; Tilbrook, R.W.; Wilson, S.E.

1995-12-01

This report evaluates the human health risks and environmental and socio-political impacts of options for recycling radioactive scrap metal (RSM) or disposing of and replacing it. Argonne National Laboratory (ANL) is assisting the US Department of Energy (DOE), Office of Environmental Restoration and Waste Management, Oak Ridge Programs Division, in assessing the implications of RSM management alternatives. This study is intended to support the DOE contribution to a study of metal recycling being conducted by the Task Group on Recycling and Reuse of the Organization for Economic Cooperation and Development. The focus is on evaluating the justification for the practice of recycling RSM, and the case of iron and steel scrap is used as an example in assessing the impacts. To conduct the evaluation, a considerable set of data was compiled and developed. Much of this information is included in this document to provide a source book of information.

Design jeans for recycling: a supply chain case study in The Netherlands.

Science.gov (United States)

van Bommel, Harrie; Goorhuis, Maarten

2014-11-01

Because the insight is raising that waste prevention needs an integral product chain approach, a product chain project was awarded with an International Solid Waste Association grant. The project decided to focus on jeans because of the large environmental impacts of cotton and the low recycling rates. The project used an open innovative approach by involving many actors from the different phases of the chain and included student and applied researchers. In a 'design jeans for recycling' students' workshop, prototypes of jeans that are easier to recycle have been developed. Integrating the new generation from different disciplines in the project proved to be very successful. The results show that an open innovation process can lead to very creative ideas and that lessons learned from this project could be used to develop new chain projects for other products. An important condition is that key actors are willing to cooperate in an open innovation approach. © The Author(s) 2014.

Feasibility of recycling thorium in a fusion-fission hybrid/PWR symbiotic system

International Nuclear Information System (INIS)

Josephs, J.M.

1980-01-01

A study was made of the economic impact of high levels of radioactivity in the thorium fuel cycle. The sources of this radioactivity and means of calculating the radioactive levels at various stages in the fuel cycle are discussed and estimates of expected levels are given. The feasibility of various methods of recycling thorium is discussed. These methods include direct recycle, recycle after storage for 14 years to allow radioactivity to decrease, shortening irradiation times to limit radioactivity build up, and the use of the window in time immediately after reprocessing where radioactivity levels are diminished. An economic comparison is made for the first two methods together with the throwaway option where thorium is not recycled using a mass energy flow model developed for a CTHR (Commercial Tokamak Hybrid Reactor), a fusion fission hybrid reactor which serves as fuel producer for several PWR reactors. The storage option is found to be most favorable; however, even this option represents a significant economic impact due to radioactivity of 0.074 mills/kW-h which amounts to $4 x 10 9 over a 30 year period assuming a 200 gigawatt supply of electrical power

Closing the fuel cycle: A superior option for India

International Nuclear Information System (INIS)

Balu, K.; Purushotham, D.S.C.; Kakodkar, A.

1999-01-01

The closed fuel cycle option with reprocessing and recycle of uranium and plutonium (U and Pu) for power generation allows better utilization of the uranium resources. On its part, plutonium is a unique energy source. During the initial years of nuclear fuel cycle activities, reprocessing and recycle of uranium and plutonium for power generation was perceived by many countries to be among the best of long term strategies for the management of spent fuel. But, over the years, some of the countries have taken a position that once-through fuel cycle is both economical and proliferation-resistant. However, such perceptions do vary as a function of economic growth and energy security of a given country. This paper deals with techno-economic perspectives of reprocessing and recycling in the Indian nuclear power programme. Experience of developing Mixed Oxide UO 2 -PuO 2 (MOX) fuel and its actual use in a power reactor (BWR) is presented. The paper further deals with the use of MOX in PHWRs in the future and current thinking, in the Indian context, in respect of advanced fuel cycles for the future. From environmental safety considerations, the separation of long-lived isotopes and minor actinides from high level waste (HLW) would enhance the acceptability of reprocessing and recycle option. The separated actinides are suitable for recycling with MOX fuel. However, the advanced fuel cycles with such recycling of Uranium and transuranium elements call for additional sophisticated fuel cycle activities which are yet to be mastered. India is interested in both uranium and thorium fuel cycles. This paper describes the current status of the Indian nuclear power scenario with reference to the program on reactors, reprocessing and radioactive waste management, plutonium recycle options, thorium-U233 fuel cycle studies and investigations on partitioning of actinides from Purex HLW as relevant to PHWR spent fuels. (author)

Final Report on Two-Stage Fast Spectrum Fuel Cycle Options

International Nuclear Information System (INIS)

Yang, Won Sik; Lin, C. S.; Hader, J. S.; Park, T. K.; Deng, P.; Yang, G.; Jung, Y. S.; Kim, T. K.; Stauff, N. E.

2016-01-01

This report presents the performance characteristics of two ''two-stage'' fast spectrum fuel cycle options proposed to enhance uranium resource utilization and to reduce nuclear waste generation. One is a two-stage fast spectrum fuel cycle option of continuous recycle of plutonium (Pu) in a fast reactor (FR) and subsequent burning of minor actinides (MAs) in an accelerator-driven system (ADS). The first stage is a sodium-cooled FR fuel cycle starting with low-enriched uranium (LEU) fuel; at the equilibrium cycle, the FR is operated using the recovered Pu and natural uranium without supporting LEU. Pu and uranium (U) are co-extracted from the discharged fuel and recycled in the first stage, and the recovered MAs are sent to the second stage. The second stage is a sodium-cooled ADS in which MAs are burned in an inert matrix fuel form. The discharged fuel of ADS is reprocessed, and all the recovered heavy metals (HMs) are recycled into the ADS. The other is a two-stage FR/ADS fuel cycle option with MA targets loaded in the FR. The recovered MAs are not directly sent to ADS, but partially incinerated in the FR in order to reduce the amount of MAs to be sent to the ADS. This is a heterogeneous recycling option of transuranic (TRU) elements

Final Report on Two-Stage Fast Spectrum Fuel Cycle Options

Energy Technology Data Exchange (ETDEWEB)

Yang, Won Sik [Purdue Univ., West Lafayette, IN (United States); Lin, C. S. [Purdue Univ., West Lafayette, IN (United States); Hader, J. S. [Purdue Univ., West Lafayette, IN (United States); Park, T. K. [Purdue Univ., West Lafayette, IN (United States); Deng, P. [Purdue Univ., West Lafayette, IN (United States); Yang, G. [Purdue Univ., West Lafayette, IN (United States); Jung, Y. S. [Purdue Univ., West Lafayette, IN (United States); Kim, T. K. [Argonne National Lab. (ANL), Argonne, IL (United States); Stauff, N. E. [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-01-30

This report presents the performance characteristics of two “two-stage” fast spectrum fuel cycle options proposed to enhance uranium resource utilization and to reduce nuclear waste generation. One is a two-stage fast spectrum fuel cycle option of continuous recycle of plutonium (Pu) in a fast reactor (FR) and subsequent burning of minor actinides (MAs) in an accelerator-driven system (ADS). The first stage is a sodium-cooled FR fuel cycle starting with low-enriched uranium (LEU) fuel; at the equilibrium cycle, the FR is operated using the recovered Pu and natural uranium without supporting LEU. Pu and uranium (U) are co-extracted from the discharged fuel and recycled in the first stage, and the recovered MAs are sent to the second stage. The second stage is a sodium-cooled ADS in which MAs are burned in an inert matrix fuel form. The discharged fuel of ADS is reprocessed, and all the recovered heavy metals (HMs) are recycled into the ADS. The other is a two-stage FR/ADS fuel cycle option with MA targets loaded in the FR. The recovered MAs are not directly sent to ADS, but partially incinerated in the FR in order to reduce the amount of MAs to be sent to the ADS. This is a heterogeneous recycling option of transuranic (TRU) elements

Actinide recycling for reactor waste mass and radiotoxicity reduction

International Nuclear Information System (INIS)

Renard, A.; Maldague, T.; Pilate, S.; Journet, J.; Rome, M.; Harislur, A.; Vergnes, J.

1994-01-01

The long-term radiotoxicity of nuclear waste from a Light Water Reactor fuel is analyzed; it can be reduced by multiple recycling of actinides in fast reactors. The capabilities of a first recycling in the light water reactor itself are evaluated with regard to implications on reactor physics and core management. Two main options are compared with their penalties and efficiency

Major issues associated with DOE commercial recycling initiatives

International Nuclear Information System (INIS)

Motl, G.P.; Burns, D.D.; Rast, D.M.

1994-01-01

Major initiatives are underway within DOE to recycle large volumes of scrap material generated during cleanup of the DOE Weapons Complex. These recycling initiatives are driven not only by the desire to conserve natural resources, but also by the recognition that shallow level burial is not a politically acceptable option. The Fernald facility is in the vanguard of a number of major DOE recycling efforts. These early efforts have brought issues to light that can have a major impact on the ability of Fernald and other major DOE sites to expand recycling efforts in the future. Some of these issues are; secondary waste deposition, title to material and radioactive contaminants, mixed waste generated during recycling, special nuclear material possession limits, cost benefit, transportation of waste to processing facilities, release criteria, and uses for beneficially reused products

Formability of recycled aluminium alloy 5017

NARCIS (Netherlands)

Sillekens, W.H.; Sano, T.; Terasaki, M.; Matsuno, K.; Kals, J.A.G.

1997-01-01

Innovations in the production of consumer goods are increasingly driven by the necessity of energy and resource conservation. As one of the consequences, designing with respect to recycleability has become an important issue, this being particularly so for non-durable items. Exemplary for the

UREP: gateway to uranium recycling

International Nuclear Information System (INIS)

Rougeau, J.P.; Durret, L.F.

1988-01-01

The industrial experience accumulated in France on recycling makes their conversion service fully reliable technically and economically. Problems associated with chemical and radiochemical behavior have been solved satisfactorily in order to offer customers flexible options for their personal optimization. Economically, a price reduction by a significant factor (up to two) has been proposed by UREP as a firm commitment for the coming years. This is the result of technical experience coupled with favorable scaling effect for the large conversion plant proposed. It is believed that such a positive approach greatly helps customers in managing recycling of their material and generating savings in their fuel cycle economics. This flow of recycled uranium, on top of the 40000 t of natural uranium consumed each year, is a valuable asset available to those utilities which have selected the reprocessing route. 2 figs

The chemical recycle of cotton

Directory of Open Access Journals (Sweden)

Alice Beyer Schuch

2016-08-01

Full Text Available The chemical recycle of cotton textiles and/or other cellulosic materials for the purpose of manufacturing regenerated high quality textiles fibres is a novel process. The objective of related research is based on the forecast of population growth, on resource scarcity predictions, and on the negative environmental impact of the textile industry. These facts lead the need of broadening the scope for long-term textile-to-textile recycle - as the mechanical recycle of natural fibres serve for limited number of cycles, still depends on input of virgin material, and offer a reduced-in-quality output. Critical analysis of scientific papers, relevant related reports, and personal interviews were the base of this study, which shows viable results in laboratorial scale of using low-quality cellulosic materials as input for the development of high-quality regenerated textile fibres though ecological chemical process. Nevertheless, to scale up and implement this innovative recycle method, other peripheral structures are requested, such as recover schemes or appropriate sort, for instance. Further researches should also be considered in regards to colours and impurities.

RECYCLING OF WATER TREATMENT PLANT SLUDGE VIA LAND APPLICATION: ASSESSMENT OF RISK

Science.gov (United States)

Water treatment sludges (WTS) offer potential benefits when applied to soil and recycling of the waste stream via land application has been proposed as a management option. Recycling of WTS to the land helps conserve landfill disposal capacity and natural resources, but potential...

Example of establishing the recycling of scrap metal as a waste management option within German regulations

International Nuclear Information System (INIS)

Bodenstein, Matthias; Delfs, Johannes; Karschnick, Oliver

2014-01-01

The German Atomic Energy Act (Atomgesetz, AtG) specifies the German nuclear licensing and supervising regulations. On that basis the German federal states are responsible for licensing and supervising of nuclear power plants (NPPs) located in that state. The Ministry of Energy, Agriculture, the Environment and Rural Areas (MELUR) is the authority responsible for the state Schleswig-Holstein, in which the NPPs Brokdorf, Brunsbuettel, Kruemmel and the research reactor HZG are located. In the licensing and supervisory procedures the authority may consult authorized experts. In addition to the AtG, the German Radiation Protection Ordinance (Strahlenschutzverordnung, StrlSchV) specifies regulations for clearance according to the 10 μSv-concept. The clearance of metal by recycling / melting is one option within the regulations of the StrlSchV. For a clearance an additional license given by the MELUR is necessary. In that license and the application documents as well as in the supervisory procedures very specific regulations are implemented. This includes regulations for clearance at third parties in foreign countries. In this talk a short introduction to the German regulations focussed on clearance according to the 10 μSv-concept will be given. The specific regulations in the license of clearance will be presented and also the application documents for NPPs in Schleswig-Holstein will be discussed. Furthermore it will be illustrated on what terms the MELUR decided to agree upon the recycling of scrap metal with the aim of clearance according to Radiation Protection 89 in foreign countries along with the German regulatory framework. (authors)

The value and feasibility of proactive recycling

International Nuclear Information System (INIS)

Fthenakis, V.M.; Moskowitz, P.D.

1999-01-01

Photovoltaics (PV) technology has definite environmental advantages over competing electricity generation technologies, and so far these advantages have driven market penetration. The PV industry follows a pro-active approach to preserve its safe and environmentally friendly nature. Industrial ecology considerations raise the issue of what to do with the PV modules at the end of their useful life. One option is recycling. This paper discusses the value of proactive recycling and compares several alternatives. copyright 1999 American Institute of Physics

TECHNOLOGY EVALUATION REPORT: TORONTO HARBOUR COMMISSIONERS (THC) SOIL RECYCLE TREATMENT TRAIN. Project Summary

Science.gov (United States)

A demonstration of the Toronto Harbour Commissioners' (THC) Soil Recycle Treatment Train was performed under the Superfund Innovative Technology Evaluation (SITE) Program at a pilot plant facility in Toronto, Ontario, Canada. The Soil Recycle Treatment Train, which consists of s...

Current and future priorities for mass and material in silicon PV module recycling

Energy Technology Data Exchange (ETDEWEB)

Olson, C.L.; Geerligs, L.J.; Goris, M.J.A.A.; Bennett, I.J. [ECN Solar Energy, P.O. Box 1, 1755 ZG Petten (Netherlands); Clyncke, J. [PV CYCLE, Rue Montoyer 23, 1000 Brussels (Belgium)

2013-10-15

A full description of the state-of-the-art PV recycling methods and their rationale is presented, which discusses the quality of the recycled materials and the fate of the substances which end up in the landfill. The aim is to flag the PV module components currently not recycled, which may have a priority in terms of their embedded energy, chemical nature or scarcity, for the next evolution of recycling. The sustainability of different recycling options, emerging in the literature on electronic waste recycling, and the possible improvement of the environmental footprint of silicon PV modules, will be discussed.

Innovative Separations Technologies

International Nuclear Information System (INIS)

Tripp, J.; Soelberg, N.; Wigeland, R.

2011-01-01

Reprocessing used nuclear fuel (UNF) is a multi-faceted problem involving chemistry, material properties, and engineering. Technology options are available to meet a variety of processing goals. A decision about which reprocessing method is best depends significantly on the process attributes considered to be a priority. New methods of reprocessing that could provide advantages over the aqueous Plutonium Uranium Reduction Extraction (PUREX) and Uranium Extraction + (UREX+) processes, electrochemical, and other approaches are under investigation in the Fuel Cycle Research and Development (FCR and D) Separations Campaign. In an attempt to develop a revolutionary approach to UNF recycle that may have more favorable characteristics than existing technologies, five innovative separations projects have been initiated. These include: (1) Nitrogen Trifluoride for UNF Processing; (2) Reactive Fluoride Gas (SF6) for UNF Processing; (3) Dry Head-end Nitration Processing; (4) Chlorination Processing of UNF; and (5) Enhanced Oxidation/Chlorination Processing of UNF. This report provides a description of the proposed processes, explores how they fit into the Modified Open Cycle (MOC) and Full Recycle (FR) fuel cycles, and identifies performance differences when compared to 'reference' advanced aqueous and fluoride volatility separations cases. To be able to highlight the key changes to the reference case, general background on advanced aqueous solvent extraction, advanced oxidative processes (e.g., volumetric oxidation, or 'voloxidation,' which is high temperature reaction of oxide UNF with oxygen, or modified using other oxidizing and reducing gases), and fluorination and chlorination processes is provided.

Innovative Separations Technologies

Energy Technology Data Exchange (ETDEWEB)

J. Tripp; N. Soelberg; R. Wigeland

2011-05-01

Reprocessing used nuclear fuel (UNF) is a multi-faceted problem involving chemistry, material properties, and engineering. Technology options are available to meet a variety of processing goals. A decision about which reprocessing method is best depends significantly on the process attributes considered to be a priority. New methods of reprocessing that could provide advantages over the aqueous Plutonium Uranium Reduction Extraction (PUREX) and Uranium Extraction + (UREX+) processes, electrochemical, and other approaches are under investigation in the Fuel Cycle Research and Development (FCR&D) Separations Campaign. In an attempt to develop a revolutionary approach to UNF recycle that may have more favorable characteristics than existing technologies, five innovative separations projects have been initiated. These include: (1) Nitrogen Trifluoride for UNF Processing; (2) Reactive Fluoride Gas (SF6) for UNF Processing; (3) Dry Head-end Nitration Processing; (4) Chlorination Processing of UNF; and (5) Enhanced Oxidation/Chlorination Processing of UNF. This report provides a description of the proposed processes, explores how they fit into the Modified Open Cycle (MOC) and Full Recycle (FR) fuel cycles, and identifies performance differences when compared to 'reference' advanced aqueous and fluoride volatility separations cases. To be able to highlight the key changes to the reference case, general background on advanced aqueous solvent extraction, advanced oxidative processes (e.g., volumetric oxidation, or 'voloxidation,' which is high temperature reaction of oxide UNF with oxygen, or modified using other oxidizing and reducing gases), and fluorination and chlorination processes is provided.

Multi-recycling of plutonium and incineration of americium, curium, and technetium in PWRs

International Nuclear Information System (INIS)

Golfier, H.; Bergeron, J.; Puill, A.; Rohart, M.

2000-01-01

The future of nuclear power requires a clear strategy for radwaste and Plutonium management. Pressurized water reactors (PWR) and the associated fuel cycle installations represent the largest part of the French power plants (and are partly paid off). The reactors in service produce an annual 10 tons of Pu, 1.4 tons of minor actinides (MA), and 3.8 tons of long-lived fission products (LLFP). The spent fuel is reprocessed in La Hague plant to recover the energetic elements U and Pu. The latter was initially dedicated to power Fast Breeder Reactors that converted the depleted and reprocessed, thus ensuring a significant part of the French national energy resources. The shut-down of Super-Phenix, the postponement of building of Fast Breeder Reactors (FBR) and the relaxed need for stretching natural U resources raise the issue of Pu management. In fact, the Pu mono-recycling practiced in France since 1987 (St Laurent B1) only slows down the Pu accumulation in spent nuclear fuel, yet it is unable to stabilize the Pu inventory. Beyond the cooperation with its industrial partners, CEA investigates solutions for short and medium term Pu management thus contributing to research required for keeping nuclear power as an energy option. The range of these investigations shall cover both adaptations for light water reactors to facilitate Pu recycling and more innovative solutions concerning reactors, fuel and fuel cycle. The aim of using Pu more efficiently in PWR has led, not only for economic and non-proliferation reasons, but also for considerations related to the optimization of Pu and MA management. The mastery of Pu inventory is a requirement for all long-lived radwaste management methods. In this context, the potential of innovative PWRs has been investigated to control the Pu fluxes and to make them a milestone on the way to clean nuclear power. This paper presents the most recent results related to Pu utilization and MA and LLFP incineration like (Am+Cm) and Tc. To

Mechanical and chemical recycling of solid plastic waste.

Science.gov (United States)

Ragaert, Kim; Delva, Laurens; Van Geem, Kevin

2017-11-01

This review presents a comprehensive description of the current pathways for recycling of polymers, via both mechanical and chemical recycling. The principles of these recycling pathways are framed against current-day industrial reality, by discussing predominant industrial technologies, design strategies and recycling examples of specific waste streams. Starting with an overview on types of solid plastic waste (SPW) and their origins, the manuscript continues with a discussion on the different valorisation options for SPW. The section on mechanical recycling contains an overview of current sorting technologies, specific challenges for mechanical recycling such as thermo-mechanical or lifetime degradation and the immiscibility of polymer blends. It also includes some industrial examples such as polyethylene terephthalate (PET) recycling, and SPW from post-consumer packaging, end-of-life vehicles or electr(on)ic devices. A separate section is dedicated to the relationship between design and recycling, emphasizing the role of concepts such as Design from Recycling. The section on chemical recycling collects a state-of-the-art on techniques such as chemolysis, pyrolysis, fluid catalytic cracking, hydrogen techniques and gasification. Additionally, this review discusses the main challenges (and some potential remedies) to these recycling strategies and ground them in the relevant polymer science, thus providing an academic angle as well as an applied one. Copyright © 2017 Elsevier Ltd. All rights reserved.

WATER RESISTANCE OF RECYCLED PAPER PANEL

Directory of Open Access Journals (Sweden)

Alexander Rani Suryandono

2017-06-01

Alice Wisler (2015 Facts about Recycling Paper. http://greenliving.lovetoknow.com/Facts_About_Recycling_Paper. Accessed 2 April 2016 Clay Miller (2011 5 Benefits of Recycling Paper. http://www.ways2gogreenblog.com/2011/09/28/5-benefits-of-recycling-paper/. Accessed 10 May 2016 Hari Goyal (2015 Grades of Paper. http://www.paperonweb.com/grade.htm. Accessed 2 April 2016 Hari Goyal (2015 Properties of Paper. http://www.paperonweb.com/paperpro.htm. Accessed 2 April 2016 Kathryn Sukalich (2016 Everything You Need to Know about Paper Recycling. http://earth911.com/business-policy/business/paper-recycling-details-basics/. Accessed 15 July 2016 [U1] Larry West (2015 Why Recycle Paper. http://environment.about.com/od/recycling/a/The-Benefits-Of-Paper-Recycling-Why-Recycle-Paper.htm. Accesed 15 June 2016 Marie-Luise Blue (2008 The Advantages of Recycling Paper. http://education.seattlepi.com/advantages-recycling-paper-3440.html. Accessed 15 June 2016 Nina Spitzer (2009 http://www.sheknows.com/home-and-gardening/articles/810025/the-impact-of-disposable-coffee-cups-on-the-environment. Accessed 15 June 2016 Radio New Zealand (2010 Iwi not Giving Up Fight against Tasman Mill Discharges. http://www.radionz.co.nz/news/regional/64521/iwi-not-giving-up-fight-against-tasman-mill-discharges. Accessed 15 July 2016 Rick LeBlanc (2016 Paper Recycling Facts, Figures and Information Sources. https://www.thebalance.com/paper-recycling-facts-figures-and-information-sources-2877868?_ga=1.192832942.544061388.1477446686. Accesed 2 April 2016 Robinson Meyer (2016 Will More Newspapers Go Nonprofit? http://www.theatlantic.com/technology/archive/2016/01/newspapers-philadelphia-inquirer-daily-news-nonprofit-lol-taxes/423960/. Accessed 3 August 2016 School of Engineering at Darthmouth (2010 Forest and Paper Industry. http://engineering.dartmouth.edu/~d30345d/courses/engs171/Paper.pdf. Accessed 2 April 2016 T. Subramani, V. Angappan. (2015. Experimental Investigation of Papercrete Concrete

Innovative Design of Plastic Bottle Recycling Box Based on ARM

Directory of Open Access Journals (Sweden)

Yuedong Xiong

2014-04-01

Full Text Available Aiming at the problems of on-site plastic bottles recycling and the reuse of waste, the automatic recycling system was developed on the basis of ARM. As the main controller, ARM not only controls the mechanical system of the collector to recover and break plastic bottles, but also communicates with and rewards the user by the automatic reward system through the wireless network. The experimental prototype test results show: post treated fragments of plastic bottles are small, which are convenient to transport and take advantage of; the operation of recovery is easy, and the interface of man-machine interaction is friendly which is easy to expand functions.

Fluorescent lamp recycling initiatives in the United States and a recycling proposal based on extended producer responsibility and product stewardship concepts.

Science.gov (United States)

Silveira, Geraldo Tr; Chang, Shoou-Yuh

2011-06-01

This paper presents an overview of mercury-containing lamp (MCL) recycling initiatives currently available in the world, especially in the United States. The majority of MCLs contain mercury which is a neurotoxin, a persistent pollutant in the environment, and can bioaccumulate in the food chain. Although there are some recycling options in the United States, collection rates are still at 23% of all potential used MCLs. This shows that citizens are either indifferent to or unaware of the recycling alternatives. On the other hand, MCL recycling seems not to be a cost-effective process and, for this reason, in the United States, take-back programmes are still sponsored only by consumers or municipalities. A few retailers have recently initiated limited take-back alternatives and manufacturers have not yet supported financially any consistent recycling alternative in the country. Considering successful experiences, this paper makes a suggestion for an MCL recycling system based on the concepts of extended producer responsibility and product stewardship. A manufacturer-importer advance recycling fee is proposed to finance the collection and recycling system while a MCL-energy recycling fee supported by the energy sector creates a lamp refund process. 'PRO Lamp', a producer responsibility organization, will manage the entire system through a widespread public-private agreement.

A Cost-Effectiveness Analysis for Incineration or Recycling of Dutch Household Plastics

NARCIS (Netherlands)

R.H.J.M. Gradus (Raymond); R. van Koppen (Rick); E. Dijkgraaf (Elbert); P. Nillesen (Paul)

2016-01-01

textabstractThe cost-effectiveness of plastic recycling is compared to energy recovery from plastic incineration in a waste-to-energy plant using data for the Netherlands. Both options have specific benefits and costs. The benefits of recycling are the avoidance of both CO2 that otherwise would be

Evaluation of fuel cycle options for plutonium utilization: 1977 study. Final report

International Nuclear Information System (INIS)

Pardue, W.M.; Madia, W.J.; Pobereskin, M.; Tripplett, M.B.; Waddell, J.D.

1977-05-01

This is the third in a series of three reports on the analysis of plutonium recycle. Analyses are based upon an October, 1976, middle case ERDA forecast of nuclear growth which predicts 510 GWe of nuclear capacity in the year 2000. Four fuel cycle options were reviewed, ranging from no LWR recycle of uranium of plutonium to recycle options both with and without breeder reactors. A special effort was devoted to the review of various estimates of the costs of reprocessing nuclear fuels, with a resulting value of $190/kg of heavy metal (deflated 1975 dollars). The associated range is estimated to $125/kg to $250/kg. Sensitivity analysis of reprocessing costs, uranium consumption, average generation costs, and total discounted costs of electricity indicate that the long-term economic advantages of plutonium recycle are quite conclusive. Nuclear scenarios which project low growth rates and which delay the start of recycle and introduction of a breeder reactor postpone the apparent economic advantages

Innovative Application of Fabric Recycling in Fashion

Directory of Open Access Journals (Sweden)

Chenyang Lee

2017-10-01

Full Text Available With the continuous development of the socialist market economy, human aesthetic standards are constantly changing, the occurrence of this situation to the development of the garment industry challenges, that is a single fabric has long been unable to meet people's aesthetic needs, And then the art of fabric reengineering will be born. This paper elaborates the meaning of fabric reworking art. This paper systematically describes the meaning of fabric reengineering to garment designer and garment itself, and comprehensively summarizes the fabric recycling technique and its characteristics.

Compositional data analysis of household waste recycling centres in Denmark

DEFF Research Database (Denmark)

Edjabou, Maklawe Essonanawe; Martín-Fernández, J. A.; Boldrin, Alessio

of these projects on the recycling rates does not exist. Thus, compositional data analysis technique was applied to analyze consistently waste data. Based on the waste composition obtained from a recycling center in Denmark, we analyzed the composition of waste treatment and disposal options. Zero and non......The Danish government has set a target of 50% recycling rates for household waste by 2022. To achieve this goal, the Danish municipalities should increase the source separation of household waste. While significant knowledge and experiences were locally gained, lessons learnt have not been...

INEL metal recycle annual report, FY-94

International Nuclear Information System (INIS)

Bechtold, T.E.

1994-09-01

In 1992, the mission of the Idaho Chemical Processing Plant was changed from reprocessing of spent nuclear fuels to development of technologies for conditioning of spent nuclear fuels and other high-level wastes for disposal in a geologic repository. In addition, the Department of Energy (DOE) directed Idaho National Engineering Laboratory (INEL) to develop a program plan addressing the management of radioactive contaminated scrap metal (RSM) within the DOE complex. Based on discussions with the EM-30 organization, the INEL Metal Recycle program plan was developed to address all issues of RSM management. Major options considered for RSM management were engineered interim storage, land disposal as low-level waste, and beneficial reuse/recycle. From its inception, the Metal Recycle program has emphasized avoidance of storage and disposal costs through beneficial reuse of RSM. The Metal Recycle program plan includes three major activities: Site-by-site inventory of RSM resources; validation of technologies for conversion of RSM to usable products; and identification of parties prepared to participate in development of a RSM recycle business

Crumb Rubber in cold recycled bituminous mixes

DEFF Research Database (Denmark)

Dondi, Giulio; Tataranni, Piergiorgio; Pettinari, Matteo

2014-01-01

Today recycling is one of the most innovative and interesting techniques for the rehabilitation of destressed road pavements. In recent years the increased interest in this process, has led to the development of various alternative methods for the recovery and the reuse of road bituminous materials...

Mass Flow Data Comparison for Comprehensive Fuel Cycle Options

International Nuclear Information System (INIS)

Kim, T.K.; Taiwo, T.A.; Wigeland, R.A.; Dixon, B.W.; Gehin, J.C.; Todosow, M.

2015-01-01

One of the key objectives stated in the United States Department of Energy, Nuclear Energy R and D road-map is the development of sustainable nuclear fuel cycles that improve natural resource utilisation and provide adequate capability and capacity to manage wastes produced by the fuel cycle. In order to inform this objective, an evaluation and screening of nuclear fuel cycle options has been conducted. As part of that effort, the entire fuel cycle options space was represented by 40 Evaluation Groups (EGs), and mass flow information for each of the EGs was provided by using an Analysis Example (AE). In this paper, the mass flow data of the 40 AEs are compared to inform on trends in the natural resource utilisation and nuclear waste generation. For the AEs that need enriched uranium support, the natural uranium required is high and the natural resource utilisation is generally lower than 2% regardless of the fuel cycle strategy (i.e., once-through, limited recycle, or continuous recycle). However, the utilisation could be improved by avoiding enriched uranium fuel support. The natural resource utilisation increases to more than 80% by recycling the nuclear fuel continuously without enriched uranium support. The combined mass of spent nuclear fuel (SNF) and high-level waste (HLW), i.e., SNF+HLW mass, is lower by using a continuous recycle option compared to a once-through fuel cycle option, because SNF mass is converted to mass of recycled products and only fission products and other process losses need to be disposed. The combined disposed mass of depleted uranium (DU), recovered uranium (RU) and thorium (RTh), i.e. DU+RU+RTh mass, has a similar trend to the uranium utilisation. For the AEs that need enriched uranium fuel, the DU and RU are the major fraction by mass of the DU+RU+RTh, which are two orders of magnitude higher in mass compared to those for the AEs that do not need enriched uranium fuel. (authors)

A Cost-Effectiveness Analysis for Incineration or Recycling of Dutch Household Plastics

NARCIS (Netherlands)

Gradus, R.H.J.M.; Nillesen, P; Dijkgraaf, E.; Koppen, R. van

2017-01-01

The cost-effectiveness of two different plastic waste treatment options is compared. This paper evaluates the recycling of plastic waste with the more conventional incineration of plastic waste, using data for the Netherlands. Both options have specific revenues and costs. The main benefit from

Repurposing Used Electric Car Batteries: A Review of Options

Science.gov (United States)

DeRousseau, Mikaela; Gully, Benjamin; Taylor, Christopher; Apelian, Diran; Wang, Yan

2017-09-01

In the United States, millions of electric and hybrid vehicles have cumulatively been sold. Although the batteries in these vehicles are expected to last at least 8 years, end-of-life options must still be considered. There are several possible options for battery packs from electric vehicles when they reach end-of-life, including remanufacturing, repurposing for a different application, and recycling. Remanufacturing is the most desirable end-of-life scenario but is the most stringent in terms of battery quality. Recycling is less desirable because there are larger material and energy losses that occur in the process. Repurposing batteries for a different use lies between these two scenarios in terms of desirability. This review paper focuses on non-automotive reuse and explores several options for using electric car battery packs in grid energy storage applications.

Sensitivity of Transmutation Capability to Recycling Scenarios in KALIMER-600 TRU Burner

International Nuclear Information System (INIS)

Lee, Yong Kyo; Kim, Myung Hyun

2013-01-01

The purpose of this study is to test transmutation and design feasibility of KALIMER burner caused from many limitations in recycling options; such as low recovery factors and external feed. Design impact from many recycling options will be tested as a sensitivity to various recycling process parameters under many recycling scenarios. Through this study, possibilities when Pyro-processing is realized with SFR can be expected in the recycling scenarios. For the development of sodium-cooled fast reactor(SFR) technology, prototype KALIMER plant is now under R and D stage in Korea. For the future application of SFR for waste transmutation, KALIMER core was designed for TRU burner by KAERI. Feasibility of TRU burner cannot be evaluated exactly because overall functional parameters in pyro-processing recycling process has not been verified yet. There is great possibility to accept undesirable process functions in pyro-processing. Only TRU nuclides composition a little differs between PWR SF and CANDU SF so first scenario has no problem operating SFR. In second scenario, the radiotoxicity of waste at 99% of TRU RF have to be confirmed whether it is proper level to reposit as Low and Intermediate Level Wastes or not. And the reactor safety at high RF of RE must be inspected. Not only third scenario but also several scenarios for good measure are being calculated and will be evaluated

Paper waste - Recycling, incineration or landfilling? A review of existing life cycle assessments

DEFF Research Database (Denmark)

Villanueva, Alejandro; Wenzel, Henrik

2007-01-01

comparisons of different management options for waste paper.\\ Despite claims of inconsistency, the LCAs reviewed illustrate the environmental benefits in recycling over incineration or landfill options, for paper and cardboard waste. This broad consensus was found despite differences in geographic location....... Such message has implications for current policy formulation on material recycling and disposal in the EU. Secondly, to identify key methodological issues of paper waste management LCAs, and enlighten the influence of such issues on the conclusions of the LCA studies. Thirdly, in light of the analysis made...... and definitions of the paper recycling/disposal systems studied. A systematic exploration of the LCA studies showed, however, important methodological pitfalls and sources of error, mainly concerning differences in the definition of the system boundaries. Fifteen key assumptions were identified that cover...

Recycling of construction and demolition waste in Kuwait

International Nuclear Information System (INIS)

Kartam, N.; Al-Mutairi, N.; Al-Ghusain, I.; Al-Humoud, J.

2002-01-01

'Full text:' There is an increasing pressure on the construction industry to reduce costs and improve our environment. The fact is that both of these goals can be achieved at the same time. Although construction and demolition (C and D) constitutes a major type of waste in terms of volume and weight, its management and recycling efforts have not seen the light in Kuwait. The goal of this research project is to study methods leading to the minimization of the total C and D waste that is landfilled in Kuwait. This can be achieved by applying the waste management hierarchy in order of importance: 1) reduce, 2) re-use, 3) recycle, 4) incineration (energy recovery), and 5) safe disposal. This paper presents the current C and D waste disposal system in Kuwait and identifies potential problems to the environment, people and economy. Then, it investigates the recycling option to manage and control this major type of waste in an economically efficient and environmentally safe manner. There are significant volumes of potentially valuable and recoverable resources being wasted in the construction industry, and these figures are continuously growing as we are starting the new millennium. C and D waste constitutes 15%-30% of all solid waste entering landfills in various countries [Bossink 1995]; and thus it is a major type of waste. An estimated 2-3 million ton of construction and demolition waste are being only disposed of in Kuwait's landfill sites each year despite the limited available land (Industrial Investment Company, 1990). C and D waste is a target because it is both heavy and bulky, and therefore undesirable for disposal in engineered, lined landfills because of the space it consumes. On the other hand, many C and D materials have high potential for recovery and use. Recovering C and D waste can help communities reach their recycling goals, preserve valuable space in their local landfills, and create better opportunities for handling other kind of waste. Therefore

Recycling schemes of Americium targets in PWR/MOX cores

International Nuclear Information System (INIS)

Maldague, Th.; Pilate, S.; Renard, A.; Harislur, A.; Mouney, H.; Rome, M.

1999-01-01

From the orientation studies performed so far, both ways to recycle Am in PWR/MOX cores, homogeneous in MOX or heterogeneous in target pins, appear feasible, provided that enriched UO 2 is used as support of the MOX fuel. Multiple recycling can then proceed and stabilize Pu and Am quantities. With respect to the Pu multiple recycling strategy, recycling Am in addition needs 1/3 more 235 U, and creates 3 times more Curium. Thus, although feasible, such a fuel cycle is complicated and brings about a significant cost penalty, not quantified yet. The advantage of the heterogeneous option is to allow to manage in different ways the Pu in MOX fuel and the Am in target pins. For example, should Am remain combined to Cm after reprocessing, the recycling of a mix of Am+Cm could be deferred to let Cm transform into Pu before irradiation. The Am+Cm targets could also stay longer in the reactor, so as to avoid further reprocessing if possible. (author)

Dynamic Systems Analysis Report for Nuclear Fuel Recycle

Energy Technology Data Exchange (ETDEWEB)

Brent Dixon; Sonny Kim; David Shropshire; Steven Piet; Gretchen Matthern; Bill Halsey

2008-12-01

This report examines the time-dependent dynamics of transitioning from the current United States (U.S.) nuclear fuel cycle where used nuclear fuel is disposed in a repository to a closed fuel cycle where the used fuel is recycled and only fission products and waste are disposed. The report is intended to help inform policy developers, decision makers, and program managers of system-level options and constraints as they guide the formulation and implementation of advanced fuel cycle development and demonstration efforts and move toward deployment of nuclear fuel recycling infrastructure.

Recycling of plastics in Germany

International Nuclear Information System (INIS)

Thienen, N. von; Patel, M.

1999-01-01

This article deals with the waste management of post-consumer plastics in Germany and its potential to save fossil fuels and reduce CO 2 emissions. Since most experience is available for packaging, the paper first gives an overview of the legislative background and the material flows for this sector. Then recycling and recovery processes for plastics waste from all sectors are assessed in terms of their contribution to energy saving and CO 2 abatement. Practically all the options studied show a better performance than waste treatment in an average incinerator which has been chosen as the reference case. High ecological benefits can be achieved by mechanical recycling if virgin polymers are substituted. The paper then presents different scenarios for managing plastic waste in Germany in 1995: considerable savings can be made by strongly enhancing the efficiency of waste incinerators. Under these conditions the distribution of plastics waste among mechanical recycling, feedstock recycling and energy recovery has a comparatively mall impact on the overall results. The maximum savings amount to 74 PJ of energy, i.e, 9% of the chemical sector energy demand in 1995 and 7.0 Mt CO 2 , representing 13% of the sector's emissions. The assessment does not support a general recommendation of energy recovery due to the large difference between the German average and the best available municipal waste-to-energy facilities and also due to new technological developments in the field of mechanical recycling

The effect of Cryogenic Crumb Rubber in cold recycled mixes for road pavements

DEFF Research Database (Denmark)

Pettinari, Matteo; Dondi, Giulio; Sangiorgi, Cesare

2014-01-01

of cold recycled mixes for road bases is considerable. Furthermore, new products are continuously being introduced or developed for recycling purposes. The objective of this research project was to test the effects, both mechanically and environmentally, of crumb rubber included in 100% Reclaimed Asphalt......Over recent years, the necessity of reducing the environmental mpact of building new infrastructures has increasingly directed research toward developing innovative manufacturing methods and materials that can satisfy these objectives. Cold recycling, widely used in renovating road pavements...

Nuclear desalination option for the international reactor innovative and secure (IRIS) design

International Nuclear Information System (INIS)

Ingersoll, D. T.; Binder, J. L.; Conti, D.; Ricotti, M. E.

2004-01-01

The worldwide demand for potable water is on the rise. A recent market survey by the World Resources Institute shows a doubling in desalinated water production every ten years from both seawater and brackish water sources. The production of desalinated water is energy intensive, requiring approximately 3-6 kWh per cubic meter of produced desalted water. At current U.S. water use rates, 1 kW of energy capacity per capita (or 1000 MW for every one million people) would be required to meet water needs with desalted water. The choice of the desalination technology determines the form of energy required: electrical energy for reverse osmosis systems, relatively low quality thermal energy for distillation systems, and both electrical and thermal energy for hybrid systems such as pre-heat RO systems. Nuclear energy plants are attractive for large scale desalination application. Nuclear plants can provide both electrical and thermal energy in an integrated, co-generated fashion to produce a spectrum of energy products including electricity, desalted water, process heat, district heating, and potentially hydrogen generation. A particularly attractive option for nuclear desalination is to couple it with an advanced, modular, passively safe reactor design such as the International Reactor Innovative and Secure (IRIS) plant. This allows for countries with smaller electrical grid needs and infrastructure to add new electrical and desalination capacity in smaller increments and at distributed sites. The safety by design nature of the IRIS reactor will ensure a safe and reliable source of energy even for countries with limited nuclear power experience and infrastructure. Two options for the application of the IRIS nuclear power plant to the cogeneration of electricity and desalted water are presented, including a coupling to a reverse osmosis plant and a multistage flash distillation plant. The results from an economic assessment of the two options are also presented.(author)

Minor Actinides Recycling in PWRs

International Nuclear Information System (INIS)

Delpech, M.; Golfier, H.; Vasile, A.; Varaine, F.; Boucher, L.; Greneche, D.

2006-01-01

Recycling of minor actinides in current and near future PWR is considered as one of the options of the general waste management strategy. This paper presents the analysis of this option both from the core physics and fuel cycle point of view. A first indicator of the efficiency of different neutron spectra for transmutation purposes is the capture to fission cross sections ratio which is less favourable by a factor between 5 to 10 in PWRs compared to fast reactors. Another indicator presented is the production of high ranking isotopes like Curium, Berkelium or Californium in the thermal or epithermal spectrum conditions of PWR cores by successive neutron captures. The impact of the accumulation of this elements on the fabrication process of such PWR fuels strongly penalizes this option. The main constraint on minor actinides loadings in PWR (or fast reactors) fuels are related to their direct impact (or the impact of their transmutation products) on the reactivity coefficients, the reactivity control means and the core kinetics parameters. The main fuel cycle physical parameters like the neutron source, the alpha decay power, the gamma and neutrons dose rate and the criticality aspects are also affected. Recent neutronic calculations based on a reference core of the Evolutionary Pressurized Reactor (EPR), indicates typical maximum values of 1 % loadings. Different fuel design options for minor actinides transmutation purposes in PWRs are presented: UOX and MOX, homogeneous and heterogeneous assemblies. In this later case, Americium loading is concentrated in specific pins of a standard UOX assembly. Recycling of Neptunium in UOX and MOX fuels was also studied to improve the proliferation resistance of the fuel. The impact on the core physics and penalties on Uranium enrichment were underlined in this case. (authors)

DWPF recycle minimization: Brainstorming session

International Nuclear Information System (INIS)

Jacobs, R.A.; Poirier, M.R.

1993-01-01

The recycle stream from the DWPF constitutes a major source of water addition to the High Level Waste evaporator system. As now designed, the entire flow of 3.5 to 6.5 gal/min (at sign 25% and 75% attainment, respectively), or 2 gal/min during idling, flow to the 2H evaporator system (Tank 43). Substantial improvement in the HLW water balance and tank volume management is expected if the DWPF recycle to the HLW evaporator system can be significantly reduced. A task team has been appointed to study alternatives for reducing the flow to the HLW evaporator system and make recommendations for implementation and/or further study and evaluation. The brainstorming session detailed in this report was designed to produce the first cut options for the task team to further evaluate

Prizes for innovation of new medicines and vaccines.

Science.gov (United States)

Love, James; Hubbard, Tim

2009-01-01

This article argues that prizes can help stimulate medical innovation, control costs and ensure greater access to new medicines and vaccines. The authors explore four increasingly ambitious prize options to reward medical innovation, each addressing flaws in the current patent system. The first option promotes innovation through a large prize fund linked to the impact on health outcomes; the second option rewards the sharing of knowledge, data, and technology with open source dividends; the third option awards prizes for interim benchmarks and discrete technical problems; and the final option removes the exclusive right to use patented inventions in upstream research in favor of prizes. The authors conclude that a system of prizes to reward drug development would break the link between R&D incentives and product prices, and that such a reform is needed to improve innovation and access to new medicines and vaccines.

Households’ Perception of Financial Incentives in Endorsing Sustainable Waste Recycling in Nigeria

Directory of Open Access Journals (Sweden)

Beatrice Abila

2018-06-01

Full Text Available Recycling is viewed as a central aspect in sustainability and mainly as pro-environmental consumer behavior. The purpose of this study is to examine the perception of households on financial incentives in endorsing sustainable recycling for municipal solid waste in Nigeria. The study was conducted in the Shomolu Local Government Area, Lagos State, Nigeria. The study also covers drivers for household willingness to recycle municipal solid waste on environmental risk, behavioral economics, resource value, economic benefit, convenience, knowledge, legislation, and belief. The result from the study asserts the hypothesis that financial incentives for recycling are vital for reducing and managing municipal solid waste sustainably. The most important driver for household willingness to recycle municipal solid waste is the detrimental environmental impacts. A moderate to positive relationship exists between households’ perception of financial incentives for recycling and drivers for household willingness to recycle municipal solid waste. The study recommends adopting the extended producer responsibility (EPR model, reverse vending options, amongst other approaches, in an effort to promote recycling culture among citizens and residents in Nigeria.

Options for Steam Generator Decommissioning

International Nuclear Information System (INIS)

Krause, Gregor; Amcoff, Bjoern; Robinson, Joe

2016-01-01

Selecting the best option for decommissioning steam generators is a key consideration in preparing for decommissioning PWR nuclear power plants. Steam Generators represent a discrete waste stream of large, complex items that can lend themselves to a variety of options for handling, treatment, recycling and disposal. Studsvik has significant experience in processing full size Steam Generators at its metal recycling facility in Sweden, and this paper will introduce the Studsvik steam generator treatment concept and the results achieved to date across a number of projects. The paper will outline the important parameters needed at an early stage to assess options and to help consider the balance between off-site and on-site treatment solutions, and the role of prior decontamination techniques. The paper also outlines the use of feasibility studies and demonstration projects that have been used to help customers prepare for decommissioning. The paper discusses physical, radiological and operational history data, Pro and Contra factors for on- and off-site treatment, the role of chemical decontamination prior to treatment, planning for off-site shipments as well as Studsvik experience This paper has an original focus upon the coming challenges of steam generator decommissioning and potential external treatment capacity constraints in the medium term. It also focuses on the potential during operations or initial shut-down to develop robust plans for steam generator management. (authors)

Utilisation of biological and secondary raw materials IX. Recycling - conversion to energy

International Nuclear Information System (INIS)

Wiemer, Klaus; Kern, Michael; Raussen, Thomas

2014-01-01

The book on the utilization of biological and secondary raw materials covers the following issues: Perspectives of the circular flow and resource economy, waste avoidance, closed substance cycle waste management law and biowaste assessment, economic evaluation and usage alternatives for biogas, consequences of the 4th BlmschV, the BioAbfV and the DueV for the biowaste treatment, alternative techniques of the Biowaste collection, alternative models of the recyclable substance assessment, future of the packaging and recyclable substance utilization, ElectroG and E-scrape recycling, innovative concepts for the municipal waste management, future of the MBA, MVA and EBS management.

The Life Cycle Cost (LCC) of Life Support Recycling and Resupply

Science.gov (United States)

Jones, Harry W.

2015-01-01

Brief human space missions supply all the crew's water and oxygen from Earth. The multiyear International Space Station (ISS) program instead uses physicochemical life support systems to recycle water and oxygen. This paper compares the Life Cycle Cost (LCC) of recycling to the LCC of resupply for potential future long duration human space missions. Recycling systems have high initial development costs but relatively low durationdependent support costs. This means that recycling is more cost effective for longer missions. Resupplying all the water and oxygen requires little initial development cost but has a much higher launch mass and launch cost. The cost of resupply increases as the mission duration increases. Resupply is therefore more cost effective than recycling for shorter missions. A recycling system pays for itself when the resupply LCC grows greater over time than the recycling LCC. The time when this occurs is called the recycling breakeven date. Recycling will cost very much less than resupply for long duration missions within the Earth-Moon system, such as a future space station or Moon base. But recycling would cost about the same as resupply for long duration deep space missions, such as a Mars trip. Because it is not possible to provide emergency supplies or quick return options on the way to Mars, more expensive redundant recycling systems will be needed.

17. Meeting municipal waste Magdeburg. Residual waste - recycling - resource; 17. Tagung Siedlungsabfallwirtschaft Magdeburg. Restabfall - Recycling - Ressource

Energy Technology Data Exchange (ETDEWEB)

Haase, Hartwig (ed.)

2012-11-01

Within the 17th meeting Waste Management at Residential Areas from 12th o 13th September, 2012 in Magdeburg (Federal Republic of Germany), the following lectures were held: (1) Opening Session - Waste management in Saxony-Anhalt (O. Aeikens); (2) World with future - the eco-social perspective (F.J. Radermacher); (3) Global commodity markets - rare earths and their recycling (I. Fahimi); (4) The further development of nearhousehold capture of recyclable materials (J. Seitel); (5) On the future of the disposal management (J. Balg); (6) Options for action for the future of the municipal waste management (A. Gosten); (7) Current models of the capture of recyclable materials in Germany (M. Kerkhoff); (8) The recycling bin as a pilot test in Hanover (R. Middendorf); (9) Position of BellandVision on the implementation of a unified recycling bin (J. Soelling); (10) What will change with the new Recycle Economy Law according to the material flows and waste treatment capacities? (H. Alwast); (11) Waste management plan Saxony-Anhalt - Current developments (S. Hagel); (12) Wastes from the thermal waste treatment - Risk potential and disposal (G.-R. Behr); (13) Landfill Mining - Contribution of the waste management to the securing of resources (K. Fricke); (14) Logistic process design and system design in the transport of wastes in developing countries using Serbia as an example (Z. Jovanovic); (15) Example of good practices in the subsequent use of landfills - Solar park Cracauer Anger (M. Harnack); (16) Ecoloop - energy efficient gasification in the limestone moving-bed (R. Moeller); (17) Utilization of waste and biomass as a resource? Only by means of an intelligent logistics. (S. Trojahn); (18) Renewable energy resources - Experiences of a network provider (J. Kempmann).

Data summary of municipal solid waste management alternatives. Volume 7, Appendix E -- Material recovery/material recycling technologies

Energy Technology Data Exchange (ETDEWEB)

None

1992-10-01

The enthusiasm for and commitment to recycling of municipal solid wastes is based on several intuitive benefits: Conservation of landfill capacity; Conservation of non-renewable natural resources and energy sources; Minimization of the perceived potential environmental impacts of MSW combustion and landfilling; Minimization of disposal costs, both directly and through material resale credits. In this discussion, ``recycling`` refers to materials recovered from the waste stream. It excludes scrap materials that are recovered and reused during industrial manufacturing processes and prompt industrial scrap. Materials recycling is an integral part of several solid waste management options. For example, in the preparation of refuse-derived fuel (RDF), ferrous metals are typically removed from the waste stream both before and after shredding. Similarly, composting facilities, often include processes for recovering inert recyclable materials such as ferrous and nonferrous metals, glass, Plastics, and paper. While these two technologies have as their primary objectives the production of RDF and compost, respectively, the demonstrated recovery of recyclables emphasizes the inherent compatibility of recycling with these MSW management strategies. This appendix discusses several technology options with regard to separating recyclables at the source of generation, the methods available for collecting and transporting these materials to a MRF, the market requirements for post-consumer recycled materials, and the process unit operations. Mixed waste MRFs associated with mass bum plants are also presented.

Energy implications of recycling packaging materials

Energy Technology Data Exchange (ETDEWEB)

Gaines, L.L. [Argonne National Lab., IL (United States); Stodolsky, F. [Argonne National Lab., Washington, DC (United States)

1994-03-01

In 1992, Congress sought to rewrite the United States comprehensive solid waste legislation -- the Resource Conservation and Recovery Act (RCRA). Commodity-specific recycling rates were proposed for consumer-goods packaging materials and newsprint We compare the impacts on energy, materials use, and landfill volume of recycling at those rates to the impacts for alternative methods of material disposition to determine the optimum for each material. After products have served their intended uses, there are several alternative paths for material disposition. These include reuse, recycling to the same product, recycling to a lower-valued product, combustion for energy recovery, incineration without energy recovery, and landfill. Only options considered to be environmentally sound are Included. Both houses of Congress specifically excluded combustion for energy recovery from counting towards the recovery goats, probably because combustion is viewed as a form of disposal and is therefore assumed to waste resources and have n environmental effects. However, co-combustion in coal-fired plants or combustion in appropriately pollution-controlled waste-to-energy plants Is safe, avoids landfill costs, and can displace fossil fuels. In some cases, more fossil fuels can be displaced by combustion than by recycling. We compare the alternative life-cycle energies to the energies for producing the products from virgin materials. Results depend on the material and on the objective to be achieved. There are trade-offs among possible goals. For instance, paper packaging recycling conserves trees but may require greater fossil-fuel input than virgin production. Therefore, the objectives for proposed legislation must be examined to see whether they can most effectively be achieved by mandated recycling rates or by other methods of disposition. The optimal choices for the United States may not necessarily be the same as those for Europe and other parts of the world.

Electricity price and Southern California's water supply options

Energy Technology Data Exchange (ETDEWEB)

Dale, Larry [Lawrence Berkeley National Laboratory, Camilla Dunham Whitehead, Andre Fargeix, Golden Gate Economics, 1 Cycltron Road, Berkeley, CA 94720 (United States)

2004-11-01

This paper evaluates the impact of fluctuating electricity prices on the cost of five options to increase the water supply to urban areas in Southern California-new surface storage, water purchases, desalination, wastewater recycling, and conservation.We show that the price of electricity required to produce and transport water influences the cost of water supply options and may alter the decision makers economic ranking of these options. When electricity prices are low, water purchase is the cost effective option. When prices exceed US$ 86/MWh, conservation of electricity and water through installation of high efficiency clothes washers is the most effective option.

Frugal innovation process

DEFF Research Database (Denmark)

Hossain, Mokter; Levänen, Jarkko; Lindeman, Sara

2017-01-01

and another developed by an individual from the Gujarat, India. Using effectuation theory we find that there are some distinct differences between two categories regarding finance, access to science and technology, the motivation of innovators, options they have, actions they take, etc....... processes. Second, we show how individuals have very different understandings of frugal innovations as well as capacities and resources needed for the development of frugal innovations. Two prominent frugal innovation cases are used in this study. One innovation was developed by individuals from the USA...

A new versatile facility: Vehicle-1 for innovative PFC concepts evaluation and its first experiments on hydrogen recycling from solid and liquid lithium

International Nuclear Information System (INIS)

Hirooka, Y.; Ohgaki, H.; Ohtsuka, Y.; Nishikawa, M.

2005-01-01

A new plasma facility: Vehicle-1 has been built for the evaluation of innovative plasma-facing component concepts. This facility can conduct experiments in such a way that standing liquids in a tray are exposed to vertically flowing plasmas, or that flowing liquids on a slope are bombarded with horizontally directed plasmas. Vehicle-1 can generate steady state hydrogen plasmas with densities of the order of 10 10 cm -3 and electron temperatures around 4 eV. Hydrogen recycling behavior has been observed in Vehicle-1, and the Arrhenius plot of rate constants exhibits a break at around 300 deg. C. The activation energies are -0.0096 eV and 0.17 eV, respectively, below and above the break. To understand the kinetics of hydrogen recycling, particles sticking coefficients have been measured. Results indicate that at temperatures below the break the sticking process appears to be rate-limiting, whereas above the break surface recombination is important. The sticking coefficients for plasma species have been found to be orders of magnitude larger than those for hydrogen molecules

Recycling phosphorus from wastewater

DEFF Research Database (Denmark)

Lemming, Camilla Kjærulff

wastewater-derived products, and to relate this to the availability from other P-containing waste products and mineral P fertiliser. This included aspects of development over time and soil accumulation, as well as effects of soil pH and the spatial distribution in soil. The P sources applied in this PhD work...... reserves. Wastewater represents the largest urban flow of P in waste. Hence, knowledge about plant P availability of products from the wastewater treatment system, and also comparison to other waste P sources and mineral P is essential to obtain an efficient recycling and to prioritise between different P...... recycling options. The work of this PhD focused on the plant P availability of sewage sludge, a P-rich residue from wastewater treatment which is commonly applied to agricultural soil in Denmark. The overall objective of the PhD work was to evaluate the plant availability of P in sewage sludge and other...

Recycling and management of waste lead-acid batteries: A mini-review.

Science.gov (United States)

Li, Malan; Liu, Junsheng; Han, Wei

2016-04-01

As a result of the wide application of lead-acid batteries to be the power supplies for vehicles, their demand has rapidly increased owing to their low cost and high availability. Accordingly, the amount of waste lead-acid batteries has increased to new levels; therefore, the pollution caused by the waste lead-acid batteries has also significantly increased. Because lead is toxic to the environment and to humans, recycling and management of waste lead-acid batteries has become a significant challenge and is capturing much public attention. Various innovations have been recently proposed to recycle lead and lead-containing compounds from waste lead-acid batteries. In this mini-review article, different recycling techniques for waste lead-acid batteries are highlighted. The present state of such recycling and its future perspectives are also discussed. We hope that this mini-review can provide useful information on recovery and recycling of lead from waste lead-acid batteries in the field of solid waste treatment. © The Author(s) 2016.

Safe recycling of materials containing persistent inorganic and carbon nanoparticles

NARCIS (Netherlands)

Reijnders, L.; Njuguna, J.; Pielichowski, K.; Zhu, H.

2014-01-01

For persistent inorganic and carbon nanomaterials, considerable scope exists for a form of recycling called ‘resource cascading’. Resource cascading is aimed at the maximum exploitation of quality and service time of natural resources. Options for resource cascading include engineered nanomaterials

Recycling and Disposal of CFLs and Other Bulbs that Contain Mercury

Science.gov (United States)

Consumers can help prevent the release of mercury into the environment by taking advantage of available local options for recycling CFLs and other household hazardous wastes, rather than disposing of them in regular household trash.

Fuel cycle cost comparison of choices in U-235 recycle in the HTGR

International Nuclear Information System (INIS)

Rothstein, M.P.

1976-07-01

An analysis of alternative options for the recycle of discharged makeup U-235 (''residual'' makeup) in HTGRs shows that the three-particle system which has been the reference plan remains optimal. This result considers both the resource utilization and the handling costs attendant to the alternative strategies (primarily in the recycle facility and in waste disposal). Furthermore, this result appears to be true under all forseeable economic conditions. A simple risk assessment indicates that recycle cost (including reprocessing, refabrication, and related waste disposal) would have to double or triple in order for the alternative U-235 recycle schemes to become attractive. This induces some degree of confidence in the choice of staying with the reference cycle in spite of the large degree of uncertainty over recycle and its costs

An approach to LCSA: the case of concrete recycling

DEFF Research Database (Denmark)

Hu, Mingming; Kleijn, René; Bozhilova-Kisheva, Kossara Petrova

2013-01-01

Purpose The framework of life cycle sustainability analysis (LCSA) has been developed within the CALCAS project but the procedure on how an LCSA should be carried out is still far from standardized. The purpose of this article is to propose an approach to put the LCSA framework into practice....... This approach is illustrated with an on-going case study on concrete recycling. Methods In the context of an EC-FP7 project on technology innovation for concrete recycling, five operational steps to implement the LCSA framework are proposed: (1) broad system definition, (2) making scenarios, (3) defining...

Traffic Light Options

DEFF Research Database (Denmark)

Jørgensen, Peter Løchte

This paper introduces, prices, and analyzes traffic light options. The traffic light option is an innovative structured OTC derivative developed independently by several London-based investment banks to suit the needs of Danish life and pension (L&P) companies, which must comply with the traffic...... 2006, and supervisory authorities in many other European countries have implemented similar regulation. Traffic light options are therefore likely to attract the attention of a wider audience of pension fund managers in the future. Focusing on the valuation of the traffic light option we set up a Black...... light scenarios. These stress scenarios entail drops in interest rates as well as in stock prices, and traffic light options are thus designed to pay off and preserve sufficient capital when interest rates and stock prices fall simultaneously. Sweden's FSA implemented a traffic light system in January...

Traffic Light Options

DEFF Research Database (Denmark)

Jørgensen, Peter Løchte

2007-01-01

This paper introduces, prices, and analyzes traffic light options. The traffic light option is an innovative structured OTC derivative developed independently by several London-based investment banks to suit the needs of Danish life and pension (L&P) companies, which must comply with the traffic...... 2006, and supervisory authorities in many other European countries have implemented similar regulation. Traffic light options are therefore likely to attract the attention of a wider audience of pension fund managers in the future. Focusing on the valuation of the traffic light option we set up a Black...... light scenarios. These stress scenarios entail drops in interest rates as well as in stock prices, and traffic light options are thus designed to pay off and preserve sufficient capital when interest rates and stock prices fall simultaneously. Sweden's FSA implemented a traffic light system in January...

Impact assessment of waste management options in Singapore.

Science.gov (United States)

Tan, Reginald B H; Khoo, Hsien H

2006-03-01

This paper describes the application of life cycle assessment for evaluating various waste management options in Singapore, a small-island city state. The impact assessment method by SimaPro is carried out for comparing the potential environmental impacts of waste treatment options including landfilling, incineration, recycling, and composting. The inventory data include gases and leachate from landfills, air emissions and energy recovery from incinerators, energy (and emission) savings from recycling, composting gases, and transport pollution. The impact assessment results for climate change, acidification, and ecotoxicity show that the incineration of materials imposes considerable harm to both human health and the environment, especially for the burning of plastics, paper/cardboard, and ferrous metals. The results also show that, although some amount of energy can be derived from the incineration of wastes, these benefits are outweighed by the air pollution (heavy metals and dioxins/furans) that incinerators produce. For Singapore, landfill gases and leachate generate minimal environmental damage because of the nation's policy to landfill only 10% of the total disposed wastes. Land transportation and separation of waste materials also pose minimal environmental damage. However, sea transportation to the landfill could contribute significantly to acidification because of the emissions of sulfur oxides and nitrogen oxides from barges. The composting of horticultural wastes hardly imposes any environmental damage. Out of all the waste strategies, the recycling of wastes offers the best solution for environmental protection and improved human health for the nation. Significant emission savings can be realized through recycling.

Sustainable recycling technologies for Solar PV off-grid system

Science.gov (United States)

Uppal, Bhavesh; Tamboli, Adish; Wubhayavedantapuram, Nandan

2017-11-01

Policy makers throughout the world have accepted climate change as a repercussion of fossil fuel exploitation. This has led the governments to integrate renewable energy streams in their national energy mix. PV off-grid Systems have been at the forefront of this transition because of their permanently increasing efficiency and cost effectiveness. These systems are expected to produce large amount of different waste streams at the end of their lifetime. It is important that these waste streams should be recycled because of the lack of available resources. Our study found that separate researches have been carried out to increase the efficiencies of recycling of individual PV system components but there is a lack of a comprehensive methodical research which details efficient and sustainable recycling processes for the entire PV off-grid system. This paper reviews the current and future recycling technologies for PV off-grid systems and presents a scheme of the most sustainable recycling technologies which have the potential for adoption. Full Recovery End-of-Life Photovoltaic (FRELP) recycling technology can offer opportunities to sustainably recycle crystalline silicon PV modules. Electro-hydrometallurgical process & Vacuum technologies can be used for recovering lead from lead acid batteries with a high recovery rate. The metals in the WEEE can be recycled by using a combination of biometallurgical technology, vacuum metallurgical technology and other advanced metallurgical technologies (utrasonical, mechano-chemical technology) while the plastic components can be effectively recycled without separation by using compatibilizers. All these advanced technologies when used in combination with each other provide sustainable recycling options for growing PV off-grid systems waste. These promising technologies still need further improvement and require proper integration techniques before implementation.

Considerations Regarding ROK Spent Nuclear Fuel Management Options

International Nuclear Information System (INIS)

Braun, Chaim; Forrest, Robert

2013-01-01

In this paper we discuss spent fuel management options in the Republic of Korea (ROK) from two interrelated perspectives: Centralized dry cask storage and spent fuel pyroprocessing and burning in sodium fast reactors (SFRs). We argue that the ROK will run out of space for at-reactors spent fuel storage by about the year 2030 and will thus need to transition centralized dry cask storage. Pyroprocessing plant capacity, even if approved and successfully licensed and constructed by that time, will not suffice to handle all the spent fuel discharged annually. Hence centralized dry cask storage will be required even if the pyroprocessing option is successfully developed by 2030. Pyroprocessing is but an enabling technology on the path leading to fissile material recycling and burning in future SFRs. In this regard we discuss two SFR options under development in the U. S.: the Super Prism and the Travelling Wave Reactor (TWR). We note that the U. S. is further along in reactor development than the ROK. The ROK though has acquired more experience, recently in investigating fuel recycling options for SFRs. We thus call for two complementary joint R and D project to be conducted by U. S. and ROK scientists. One leading to the development of a demonstration centralized away-from-reactors spent fuel storage facility. The other involve further R and D on a combined SFR-fuel cycle complex based on the reactor and fuel cycle options discussed in the paper

Linear feature extraction from radar imagery: SBIR (Small Business Innovative Research) phase 2, option 1

Science.gov (United States)

Conner, Gary D.; Milgram, David L.; Lawton, Daryl T.; McConnell, Christopher C.

1988-04-01

The goal of this effort is to develop and demonstrate prototype processing capabilities for a knowledge-based system to automatically extract and analyze linear features from synthetic aperture radar (SAR) imagery. This effort constitutes Phase 2 funding through the Defense Small Business Innovative Research (SBIR) Program. Previous work examined the feasibility of the technology issues involved in the development of an automatedlinear feature extraction system. This Option 1 Final Report documents this examination and the technologies involved in automating this image understanding task. In particular, it reports on a major software delivery containing an image processing algorithmic base, a perceptual structures manipulation package, a preliminary hypothesis management framework and an enhanced user interface.

Sustainability Features of Nuclear Fuel Cycle Options

Directory of Open Access Journals (Sweden)

Stefano Passerini

2012-09-01

Full Text Available The nuclear fuel cycle is the series of stages that nuclear fuel materials go through in a cradle to grave framework. The Once Through Cycle (OTC is the current fuel cycle implemented in the United States; in which an appropriate form of the fuel is irradiated through a nuclear reactor only once before it is disposed of as waste. The discharged fuel contains materials that can be suitable for use as fuel. Thus, different types of fuel recycling technologies may be introduced in order to more fully utilize the energy potential of the fuel, or reduce the environmental impacts and proliferation concerns about the discarded fuel materials. Nuclear fuel cycle systems analysis is applied in this paper to attain a better understanding of the strengths and weaknesses of fuel cycle alternatives. Through the use of the nuclear fuel cycle analysis code CAFCA (Code for Advanced Fuel Cycle Analysis, the impact of a number of recycling technologies and the associated fuel cycle options is explored in the context of the U.S. energy scenario over 100 years. Particular focus is given to the quantification of Uranium utilization, the amount of Transuranic Material (TRU generated and the economics of the different options compared to the base-line case, the OTC option. It is concluded that LWRs and the OTC are likely to dominate the nuclear energy supply system for the period considered due to limitations on availability of TRU to initiate recycling technologies. While the introduction of U-235 initiated fast reactors can accelerate their penetration of the nuclear energy system, their higher capital cost may lead to continued preference for the LWR-OTC cycle.

Cork Design : A Design Action Intervention Approach Towards Sustainable Product Innovation

NARCIS (Netherlands)

Mestre, A.C.C.M.

2014-01-01

The study Cork Design: A Design Action Intervention Approach Towards Sustainable Product Innovation comprises the systematic implementation of sustainable product innovation within the Portuguese cork sector, through action research. Cork is a natural, recyclable, non-toxic, and renewable resource,

THE INNOVATIVE POLICY OPTIONS FOR COASTAL FISHERIES ECONOMIC DEVELOPMENT: A CASE OF KWANDANG BAY COASTAL ECOSYSTEM

Directory of Open Access Journals (Sweden)

Noel Taylor Moore

2017-07-01

Full Text Available Socio-environmental problems, such as climate change, pollution and habitat destruction, present serious challenges for fisheries economic development. The integration of interventions or investments within a coastal marine ecosystem, a defined spatial area, is considered important in the economic development of local communities leading to the planned outcomes of livelihoods, food security and conservation The coastal marine ecosystem, is the provider of products and services to the local economy adjacent to the ecosystem where the benefit flows, within that area, are interconnected. The roles of science, technology and innovation (STI are an integral part of these multi-dimensional interventions. Hence the need for an integrated approach for these interventions by government and/or through donor funded projects to enhance economic development of coastal communities. The policy framework proposed is therefore an STI perspective of the links between these intervention and investment options, based on a ‘fisheries economic development Hub’ (Hub and discussed using the multi-level perspective (MLP. The policy innovation proposal suggests an implementation strategy of a pilot project and analyses the selection and implications of a potential Indonesian site for the application of the Hub. This paper aims to introduce the MLP into the framework of coastal community-based fisheries economic development.   Key words: policy innovation. coastal marine ecosystem, fisheries economic development Hub, value chains, multi-level perspective (MLP

Phosphorus Import Dependency and Recycling Potential in the Global Phosphorus Mosaic

Science.gov (United States)

Powers, S. M.

2017-12-01

Nations differ widely in terms of recent P consumption trends and fertilizer trade dependencies, reflecting dynamic and globally uneven P fertilizer production, consumption, export, and import. Recovered P from urban and agricultural wastes can provide renewable sources that supplant the need to import P fertilizer, but to date, research on P recycling potential has been highly spatially segregated. Understanding of the global distribution of P recycling potential and options, and how these intersect with P import dependencies, could be used to guide long-term, spatially-prioritized planning for P, food, and water security. We integrated recent data on national P fertilizer flows, subnational P use, and landscape features within a global grid to understand how these constraints on future options for P use are distributed worldwide. This analysis illustrates several regions where combinations of high population density, cropland extent, and manure P production provide islands of opportunity for P recycling in mixed crop-livestock and populous agricultural areas. At the same time, nations with lower import ratios (net P import:consumption) contained a disproportionately large share of manure-rich croplands and populous croplands. As a further demonstration of the kinds of integrated comparisons that are possible using global land use data sets in combination with P, worldwide similarities and distinctions for P emerged from a cluster analysis. These kinds of socioeconomic-geographic patterns may foretell distinct P futures as societies address spatially uneven options for P, food, and water security.

Initial research on recycled tyre bales for road infrastructure applications

Science.gov (United States)

Duda, Aleksander; Sobala, Dariusz

2017-12-01

The paper reviews selected surveys carried out within the R&D project, co-financed with the European Regional Development Fund, called "ReUse - Innovative Recycling Materials, Enhancing the Sustainability of Bridge Facilities" (Innotech No. K3 / IN3 / 38/228116 / NCBiR / 15). The aim of the project and conducted research is to develop and implement innovative, cheap and environmentally-friendly recycled construction material in the form of tyre bales made from compressed used car tyres. This material is likely to be applied in civil engineering, especially in transport infrastructure, geotechnical and hydraulic engineering. New material is cheap and has unique properties such as low weight, high water permeability, high vibration and noise-damping capacity, low pressure coefficient values and other parameters that technically and economically allow it to replace natural aggregates. The extensive practical application of new material will facilitate the replacement of waste management methods with the environmentally friendly ones.

Sustainable recycling technologies for Solar PV off-grid system

Directory of Open Access Journals (Sweden)

Uppal Bhavesh

2017-01-01

Full Text Available Policy makers throughout the world have accepted climate change as a repercussion of fossil fuel exploitation. This has led the governments to integrate renewable energy streams in their national energy mix. PV off-grid Systems have been at the forefront of this transition because of their permanently increasing efficiency and cost effectiveness. These systems are expected to produce large amount of different waste streams at the end of their lifetime. It is important that these waste streams should be recycled because of the lack of available resources. Our study found that separate researches have been carried out to increase the efficiencies of recycling of individual PV system components but there is a lack of a comprehensive methodical research which details efficient and sustainable recycling processes for the entire PV off-grid system. This paper reviews the current and future recycling technologies for PV off-grid systems and presents a scheme of the most sustainable recycling technologies which have the potential for adoption. Full Recovery End-of-Life Photovoltaic (FRELP recycling technology can offer opportunities to sustainably recycle crystalline silicon PV modules. Electro-hydrometallurgical process & Vacuum technologies can be used for recovering lead from lead acid batteries with a high recovery rate. The metals in the WEEE can be recycled by using a combination of biometallurgical technology, vacuum metallurgical technology and other advanced metallurgical technologies (utrasonical, mechano-chemical technology while the plastic components can be effectively recycled without separation by using compatibilizers. All these advanced technologies when used in combination with each other provide sustainable recycling options for growing PV off-grid systems waste. These promising technologies still need further improvement and require proper integration techniques before implementation.

Lithium actinide recycle process demonstration

Energy Technology Data Exchange (ETDEWEB)

Johnson, G.K.; Pierce, R.D.; McPheeters, C.C. [Argonne National Laboratory, IL (United States)

1995-10-01

Several pyrochemical processes have been developed in the Chemical Technology Division of Argonne Laboratory for recovery of actinide elements from LWR spent fuel. The lithium process was selected as the reference process from among the options. In this process the LWR oxide spent fuel is reduced by lithium at 650{degrees}C in the presence of molten LiCl. The Li{sub 2}O formed during the reduction process is soluble in the salt. The spent salt and lithium are recycled after the Li{sub 2}O is electrochemically reduced. The oxygen is liberated as CO{sub 2} at a carbon anode or oxygen at an inert anode. The reduced metal components of the LWR spent fuel are separated from the LiCL salt phase and introduced into an electrorefiner. The electrorefining step separates the uranium and transuranium (TRU) elements into two product streams. The uranium product, which comprises about 96% of the LWR spent fuel mass, may be enriched for recycle into the LWR fuel cycle, stored for future use in breeder reactors, or converted to a suitable form for disposal as waste. The TRU product can be recycled as fast reactor fuel or can be alloyed with constituents of the LWR cladding material to produce a stable waste form.

Transmutation Dynamics: Impacts of Multi-Recycling on Fuel Cycle Performances

Energy Technology Data Exchange (ETDEWEB)

S. Bays; S. Piet; M. Pope; G. Youinou; A. Dumontier; D. Hawn

2009-09-01

From a physics standpoint, it is feasible to sustain continuous multi-recycle in either thermal or fast reactors. In Fiscal Year 2009, transmutaton work at INL provided important new insight, caveats, and tools on multi-recycle. Multi-recycle of MOX, even with all the transuranics, is possible provided continuous enrichment of the uranium phase to ~6.5% and also limitting the transuranic enrichment to slightly less than 8%. Multi-recycle of heterogeneous-IMF assemblies is possible with continuous enrichment of the UOX pins to ~4.95% and having =60 of the 264 fuel pins being inter-matrix. A new tool enables quick assessment of the impact of different cooling times on isotopic evolution. The effect of cooling time was found to be almost as controlling on higher mass actinide concentrations in fuel as the selection of thermal versus fast neutron spectra. A new dataset was built which provides on-the-fly estimates of gamma and neutron dose in MOX fuels as a function of the isotopic evolution. All studies this year focused on the impact of dynamic feedback due to choices made in option space. Both the equilibrium fuel cycle concentrations and the transient time to reach equilibrium for each isotope were evaluated over a range of reactor, reprocessing and cooling time combinations. New bounding cases and analysis methods for evaluating both reactor safety and radiation worker safety were established. This holistic collection of physics analyses and methods gives improved resolution of fuel cycle options, and impacts thereof, over that of previous ad-hoc and single-point analyses.

Expanded recycling at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Betschart, J.F.; Malinauskas, L.; Burns, M.

1996-01-01

The Pollution Prevention Program Office has increased recycling activities, reuse, and options to reduce the solid waste streams through streamlining efforts that applied best management practices. The program has prioritized efforts based on volume and economic considerations and has greatly increased Los Alamos National Laboratory's (LANL's) recycle volumes. The Pollution Prevention Program established and chairs a Solid Waste Management Solutions Group to specifically address and solve problems in nonradioactive, Resource Conservation and Recovery Act (RCRA), state-regulated, and sanitary and industrial waste streams (henceforth referred to as sanitary waste in this paper). By identifying materials with recycling potential, identifying best management practices and pathways to return materials for reuse, and introducing the concept and practice of open-quotes asset management,open-quotes the Group will divert much of the current waste stream from disposal. This Group is developing procedures, agreements, and contracts to stage, collect, sort, segregate, transport and process materials, and is also garnering support for the program through the involvement of upper management, facility managers, and generators

Mathematician meets Fashion designer : The future of fashion will be multidisciplinary innovation!

NARCIS (Netherlands)

Toeters, M.J.; Feijs, L.M.G.

2016-01-01

The fashion system recycles the same ideas over and over again, with a very low rate of innovation. We found each other at the cutting edge of fashion innovation and claim that much, much more innovation is possible. We found it is time to analyse our collaborative work and put it in the global

Recovering valuable metals from recycled photovoltaic modules.

Science.gov (United States)

Yi, Youn Kyu; Kim, Hyun Soo; Tran, Tam; Hong, Sung Kil; Kim, Myong Jun

2014-07-01

Recovering valuable metals such as Si, Ag, Cu, and Al has become a pressing issue as end-of-life photovoltaic modules need to be recycled in the near future to meet legislative requirements in most countries. Of major interest is the recovery and recycling of high-purity silicon (> 99.9%) for the production of wafers and semiconductors. The value of Si in crystalline-type photovoltaic modules is estimated to be -$95/kW at the 2012 metal price. At the current installed capacity of 30 GW/yr, the metal value in the PV modules represents valuable resources that should be recovered in the future. The recycling of end-of-life photovoltaic modules would supply > 88,000 and 207,000 tpa Si by 2040 and 2050, respectively. This represents more than 50% of the required Si for module fabrication. Experimental testwork on crystalline Si modules could recover a > 99.98%-grade Si product by HNO3/NaOH leaching to remove Al, Ag, and Ti and other metal ions from the doped Si. A further pyrometallurgical smelting at 1520 degrees C using CaO-CaF2-SiO2 slag mixture to scavenge the residual metals after acid leaching could finally produce > 99.998%-grade Si. A process based on HNO3/NaOH leaching and subsequent smelting is proposed for recycling Si from rejected or recycled photovoltaic modules. Implications: The photovoltaic industry is considering options of recycling PV modules to recover metals such as Si, Ag, Cu, Al, and others used in the manufacturing of the PV cells. This is to retain its "green" image and to comply with current legislations in several countries. An evaluation of potential resources made available from PV wastes and the technologies used for processing these materials is therefore of significant importance to the industry. Of interest are the costs of processing and the potential revenues gained from recycling, which should determine the viability of economic recycling of PV modules in the future.

The potential environmental gains from recycling waste plastics: Simulation of transferring recycling and recovery technologies to Shenyang, China

International Nuclear Information System (INIS)

Chen Xudong; Xi Fengming; Geng Yong; Fujita, Tsuyoshi

2011-01-01

Research highlights: → Urban symbiosis creates compatibility of industrial development and waste management. → Mechanical technology leads to more CO 2 emission reduction. → Energy recovery technology leads to more fossil fuel saving. → Clean energy makes recycling technologies cleaner. → Demand management is crucial for realizing potential environmental gains of recycling. - Abstract: With the increasing attention on developing a low-carbon economy, it is necessary to seek appropriate ways on reducing greenhouse gas (GHG) emissions through innovative municipal solid waste management (MSWM), such as urban symbiosis. However, quantitative assessments on the environmental benefits of urban symbiosis, especially in developing countries, are limited because only a limited number of planned synergistic activities have been successful and it is difficult to acquire detailed inventory data from private companies. This paper modifies and applies a two-step simulation system and used it to assess the potential environmental benefits, including the reduction of GHG emissions and saving of fossil fuels, by employing various Japanese plastics recycling/energy-recovery technologies in Shenyang, China. The results showed that among various recycling/energy-recovery technologies, the mechanical waste plastics recycling technology, which produces concrete formwork boards (NF boards), has the greatest potential in terms of reducing GHG emissions (1.66 kg CO 2 e/kg plastics), whereas the technology for the production of refuse plastic fuel (RPF) has the greatest potential on saving fossil fuel consumption (0.77 kgce/kg-plastics). Additional benefits can be gained by applying combined technologies that cascade the utilization of waste plastics. Moreover, the development of clean energy in conjunction with the promotion of new waste plastics recycling programs could contribute to additional reductions in GHG emissions and fossil fuel consumption.

Life cycle assessment of a road safety product made with virgin and recycled HDPE.

Science.gov (United States)

Simões, Carla L; Xará, Susana M; Bernardo, C A

2011-04-01

The present study aims at evaluating the potential environmental impact of using recycled high-density polyethylene (HDPE) in the production of an anti-glare lamella (AGL), a road safety device currently manufactured from virgin (not recycled) polymer. The impact was evaluated using the life cycle assessment (LCA) technique and comparing two alternative systems: current AGL, manufactured from virgin HDPE, and optional AGL, made with recycled HDPE obtained from post-consumer packages. The AGL manufacturing phase was found to be responsible for most of the impacts in both systems, with the production of the raw material being the largest contributor for that phase. The present study makes a contribution to the problem of developing value-added products made from post-consumer polymeric recyclates.

Feasibility of Target Material Recycling as Waste Management Alternative

International Nuclear Information System (INIS)

El-Guebaly, L.; Wilson, P.; Henderson, D.; Varuttamaseni, A.

2004-01-01

The issue of waste management has been studied simultaneously along with the development of the ARIES heavy-ion-driven inertial fusion energy (IFE) concept. Options for waste management include disposal in repositories, recycling, or clearance from regulatory control, following a reasonable cooling period. This paper concerns the feasibility of recycling the heavy-ion-beam targets, in particular the hohlraum wall materials that include, for example, Au/Gd, Au, W, Pb, Hg, Ta, Pb/Ta/Cs, Hg/W/Cs, Pb/Hf, Hf, solid Kr, and solid Xe. The choice between target material disposal and recycling depends on the amount of waste generated relative to the nuclear island, the strategy to solve the recycling problem, and the impact of the additional cost and complexity of the recycling process on the overall machine. A detailed flow diagram for the elements of the recycling process was developed to analyze two extreme activation cases: (a) one-shot use and then disposal in a repository and (b) recycling continuously during plant life without removal of transmutation products. Metrics for comparing the two scenarios included waste level, dose to recycling equipment, additional cost, and design complexity. Comparing the two approaches indicated a preference for the one-shot scenario as it generates 1 m 3 /yr of extremely low-level waste (Class A) and offers attractive design and economics features. Recycling reduces the target waste stream by a factor of 10 or more but introduces additional issues. It may produce high-level waste, requires remote handling, adds radioactive storage facilities, and increases the cost and complexity of the plant. The inventory analysis indicated that the heavy-ion-beam (HIB) target materials represent a very small waste stream compared to that of the nuclear island (<1% of the total waste). This means recycling is not a 'must' requirement for IFE-HIB power plants unless the target materials have cost and/or resource problems (e.g., Au and Gd). In this

Disposal Options of Bamboo Fabric-Reinforced Poly(Lactic Acid Composites for Sustainable Packaging: Biodegradability and Recyclability

Directory of Open Access Journals (Sweden)

M.R. Nurul Fazita

2015-08-01

Full Text Available The present study was conducted to determine the recyclability and biodegradability of bamboo fabric-reinforced poly(lactic acid (BF-PLA composites for sustainable packaging. BF-PLA composite was recycled through the granulation, extrusion, pelletization and injection processes. Subsequently, mechanical properties (tensile, flexural and impact strength, thermal stability and the morphological appearance of recycled BF-PLA composites were determined and compared to BF-PLA composite (initial materials and virgin PLA. It was observed that the BF-PLA composites had the adequate mechanical rigidity and thermal stability to be recycled and reused. Moreover, the biodegradability of BF-PLA composite was evaluated in controlled and real composting conditions, and the rate of biodegradability of BF-PLA composites was compared to the virgin PLA. Morphological and thermal characteristics of the biodegradable BF-PLA and virgin PLA were obtained by using environment scanning electron microscopy (ESEM and differential scanning calorimetry (DSC, respectively. The first order decay rate was found to be 0.0278 and 0.0151 day−1 in a controlled composting condition and 0.0008 and 0.0009 day−1 in real composting conditions for virgin PLA and BF-PLA composite, respectively. Results indicate that the reinforcement of bamboo fabric in PLA matrix minimizes the degradation rate of BF-PLA composite. Thus, BF-PLA composite has the potential to be used in product packaging for providing sustainable packaging.

Assessment of DOE radioactive scrap metal disposition options

International Nuclear Information System (INIS)

Butler, C.R.; Kasper, K.M.; Bossart, S.J.

1997-01-01

The DOE has amassed a large amount of radioactively-contaminated scrap metal (RSM) as a result of past operations and decontamination and decommissioning (D ampersand D) projects. The volume of RSM will continue to increase as a result of the D ampersand D of more than 6,000 surplus facilities and many of the 14,000 operating facilities in the DOE complex. RSM can be either surface contaminated or volumetrically contaminated, or both, with varying amounts of radioactivity. Several options exist for the disposition of this RSM, including disposal as radioactive waste, recycling by decontamination and free-release for unrestricted use, or recycling for restricted reuse inside a DOE controlled area. The DOE Office of Science and Technology (EM-50) has been actively investing in technology and strategy development in support of restricted-reuse RSM recycling for the past several years. This paper will assess the nature of the RSM recycling issue, review past investment by DOE to develop technologies and strategies to recycle RSM, and then discuss some recommendations concerning future investments in support of RSM management. Available information on the supply of RSM will be presented in Section II. The regulatory and policy framework concerning recycling RSM will be presented in Section III. A review of DOE investment in RSM recycling technology and current programs will be presented in Section IV. The current and projected industrial capacity will be described in Section V. And, finally, a discussion of issues and recommendations regarding DOE technology development interests in RSM recycling will be presented in Section VI and VII, respectively

Assessment of DOE radioactive scrap metal disposition options

Energy Technology Data Exchange (ETDEWEB)

Butler, C.R.; Kasper, K.M. [Waste Policy Institute, Morgantown, WV (United States); Bossart, S.J. [Department of Energy, Morgantown, WV (United States)

1997-02-01

The DOE has amassed a large amount of radioactively-contaminated scrap metal (RSM) as a result of past operations and decontamination and decommissioning (D&D) projects. The volume of RSM will continue to increase as a result of the D&D of more than 6,000 surplus facilities and many of the 14,000 operating facilities in the DOE complex. RSM can be either surface contaminated or volumetrically contaminated, or both, with varying amounts of radioactivity. Several options exist for the disposition of this RSM, including disposal as radioactive waste, recycling by decontamination and free-release for unrestricted use, or recycling for restricted reuse inside a DOE controlled area. The DOE Office of Science and Technology (EM-50) has been actively investing in technology and strategy development in support of restricted-reuse RSM recycling for the past several years. This paper will assess the nature of the RSM recycling issue, review past investment by DOE to develop technologies and strategies to recycle RSM, and then discuss some recommendations concerning future investments in support of RSM management. Available information on the supply of RSM will be presented in Section II. The regulatory and policy framework concerning recycling RSM will be presented in Section III. A review of DOE investment in RSM recycling technology and current programs will be presented in Section IV. The current and projected industrial capacity will be described in Section V. And, finally, a discussion of issues and recommendations regarding DOE technology development interests in RSM recycling will be presented in Section VI and VII, respectively.

Nuclear Waste Vitrification in the U.S.: Recent Developments and Future Options

International Nuclear Information System (INIS)

Vienna, John D.

2010-01-01

Nuclear power plays a key role in maintaining current world wide energy growth while minimizing the greenhouse gas emissions. A disposition path for used nuclear fuel (UNF) must be found for this technology to achieve its promise. One likely option is the recycling of UNF and immobilization of the high-level waste (HLW) by vitrification. Vitrification is the technology of choice for immobilizing HLW from defense and commercial fuel reprocessing around the world. Recent advances in both recycling technology and vitrification show great promise in closing the nuclear fuel cycle in an efficient and economical fashion. This article summarizes the recent trends developments and future options in waste vitrification for both defense waste cleanup and closing the nuclear fuel cycle in the U.S.

Plastic recycling in the Nordics: A value chain market analysis.

Science.gov (United States)

Milios, Leonidas; Holm Christensen, Lena; McKinnon, David; Christensen, Camilla; Rasch, Marie Katrine; Hallstrøm Eriksen, Mikael

2018-06-01

There is low utilisation of plastic waste in the Nordic region and only a fraction of plastic materials go back into production processes through reuse and recycling practices. This paper aims to increase knowledge concerning factors that inhibit demand for recycled plastics, and to identify critical barriers for plastic recycling across the regional plastics value chain. A literature review and targeted interviews with key actors across the plastics value chain enabled the mapping of interactions between the major actors and identified hotspots that act as barriers to the flow of plastic materials. Barriers identified include the lack of both supply and demand of recycled plastic and are mainly attributed to the fragmented market of secondary materials. The main hotspots identified are the low demand due to price considerations, insufficient traceability and transparency in value chain transactions, and general design deficiencies in the recyclability of products. Value chain coordination is considered as the most important intervention by the interviewees, followed by the need for increased investment in innovation and technology development. Complementary measures that could counteract the identified barriers include public procurement for resource efficiency, ban on the incineration of recyclable materials, and specifications on the design of plastic products for reducing the number of different polymers, and the number and usage of additives. Copyright © 2018 Elsevier Ltd. All rights reserved.

WasteWise Resource Management: Innovative Solid Waste Contracting Methods

Science.gov (United States)

Resource management is an innovative contractual partnership between a waste-generating organization and a qualified contractor that changes the nature of current disposal services to support waste minimization and recycling.

Direction of CRT waste glass processing: electronics recycling industry communication.

Science.gov (United States)

Mueller, Julia R; Boehm, Michael W; Drummond, Charles

2012-08-01

Cathode Ray Tube, CRT, waste glass recycling has plagued glass manufacturers, electronics recyclers and electronics waste policy makers for decades because the total supply of waste glass exceeds demand, and the formulations of CRT glass are ill suited for most reuse options. The solutions are to separate the undesirable components (e.g. lead oxide) in the waste and create demand for new products. Achieving this is no simple feat, however, as there are many obstacles: limited knowledge of waste glass composition; limited automation in the recycling process; transportation of recycled material; and a weak and underdeveloped market. Thus one of the main goals of this paper is to advise electronic glass recyclers on how to best manage a diverse supply of glass waste and successfully market to end users. Further, this paper offers future directions for academic and industry research. To develop the recommendations offered here, a combination of approaches were used: (1) a thorough study of historic trends in CRT glass chemistry; (2) bulk glass collection and analysis of cullet from a large-scale glass recycler; (3) conversations with industry members and a review of potential applications; and (4) evaluation of the economic viability of specific uses for recycled CRT glass. If academia and industry can solve these problems (for example by creating a database of composition organized by manufacturer and glass source) then the reuse of CRT glass can be increased. Copyright © 2012 Elsevier Ltd. All rights reserved.

Pollution prevention opportunity assessment for Sandia National Laboratories/California recycling programs.

Energy Technology Data Exchange (ETDEWEB)

Wrons, Ralph Jordan; Vetter, Douglas Walter

2007-07-01

This Pollution Prevention Opportunity Assessment (PPOA) was conducted for the Sandia National Laboratories/California (SNL/CA) Environmental Management Department between May 2006 and March 2007, to evaluate the current site-wide recycling program for potential opportunities to improve the efficiency of the program. This report contains a summary of the information collected and analyses performed with recommended options for implementation. The SNL/NM Pollution Prevention (P2) staff worked with the SNL/CA P2 Staff to arrive at these options.

"We Was Regenerated Out": Regeneration, Recycling and Devaluing Communities

Directory of Open Access Journals (Sweden)

Luna Glucksberg

2014-12-01

Full Text Available This article looks at well documented processes of urban regeneration and community displacement in the inner-city through an innovative anthropological perspective focused on concepts of waste and value. Using the notion of symbolic devaluation of the working classes developed by Skeggs (1997; 2004, it traces their exclusion from recycling practices while at the same time the estates they live on are being regenerated. Raising questions about the parallels and contradictions between regeneration and recycling, it shows how symbolic devaluation of specifi c areas and their inhabitants are necessary precursors of the physical demolition and removal that characterize regeneration processes. Through an ethnographic approach, the deep connections between people and their waste, and people as waste, are exposed and questioned, showing how valuable middle class selves are produced through appropriate waste management procedures, i.e. individualized recycling, while inner-city, estate dwellers are remade into uncaring, unworthy citizens who cannot take part in this value-producing circuit.

Evolution of water recycling in Australian cities since 2003.

Science.gov (United States)

Radcliffe, J C

2010-01-01

The prolonged Australian drought which commenced in 2002, and the agreement between Australia's Commonwealth and States/Territories governments to progress water reform through the National Water Initiative, has resulted in many new recycling projects in Australia's capital cities. Dual reticulation systems are being advanced in new subdivision developments in Sydney, Melbourne and Adelaide. Brisbane has installed three large Advanced Water Treatment Plants that are designed to send indirect potable recycled water to the Wivenhoe Dam which is Brisbane's principal water reservoir. Numerous water recycling projects are serving industry and agriculture. Experimental managed aquifer recharge is being undertaken with wetland-treated stormwater in Adelaide and reverse osmosis treated wastewater in Perth. New National Water Quality Management Strategy recycled water guidelines have been developed for managing environmental risks, for augmentation of drinking water supplies, for managed aquifer recharge and for stormwater harvesting and reuse. Many recent investments are part-supported through Commonwealth government grants. Desalination plants are being established in Melbourne and Adelaide and a second one in Perth in addition to the newly-operational plants in Perth, South-East Queensland and Sydney. Despite there being numerous examples of unplanned indirect potable recycling, most governments remain reluctant about moving towards planned potable recycling. There is evidence of some policy bans still being maintained by governments but the National Water Commission continues to reinforce the necessity of an even-handed objective consideration of all water supply options.

U.S. Department of Energy National Center of Excellence for Metals Recycle

International Nuclear Information System (INIS)

Adams, V.; Bennett, M.; Bishop, L.

1998-05-01

The US Department of Energy (DOE) National Center of Excellence for Metals Recycle has recently been established. The vision of this new program is to develop a DOE culture that promotes pollution prevention by considering the recycle and reuse of metal as the first and primary disposition option and burial as a last option. The Center of Excellence takes the approach that unrestricted release of metal is the first priority because it is the most cost-effective disposition pathway. Where this is not appropriate, restricted release, beneficial reuse, and stockpile of ingots are considered. Current recycling activities include the sale of 40,000 tons of scrap metal from the East Tennessee Technology Park (formerly K-25 Plant) K-770 scrap yard, K-1064 surplus equipment and machinery, 7,000 PCB-contaminated drums, 12,000 tons of metal from the Y-l2 scrap yard, and 1,000 metal pallets. In addition, the Center of Excellence is developing a toolbox for project teams that will contain a number of specific tools to facilitate metals recycle. This Internet-based toolbox will include primers, computer programs, and case studies designed to help sites to perform life cycle analysis, perform ALARA (As Low As is Reasonably Achievable) analysis for radiation exposures, provide pollution prevention information and documentation, and produce independent government estimates. The use of these tools is described for two current activities: disposition of scrap metal in the Y-12 scrapyard, and disposition of PCB-contaminated drums

Heterogeneous Recycle of Transuranics Fuels in Fast Reactors

International Nuclear Information System (INIS)

Hoffman, Edward; Taiwo, Temitope; Hill, Robert

2008-01-01

A preliminary physics evaluation of the impacts of heterogeneous recycle using Pu+Np driver and minor actinide target fuel assemblies in fast reactor cores has been performed by comparing results to those obtained for a reference homogeneous recycle core using driver assemblies containing grouped transuranic (TRU) fuel. Parametric studies are performed on the reference heterogeneous recycle core to evaluate the impacts of variations in the pre- and post-separation cooling times, target material type (uranium and non-uranium based), target amount and location, and other parameters on the system performance. This study focused on startup, single-pass cores for the purpose of quantifying impacts and also included comparisons to the option of simply storing the LWR spent nuclear fuel over a 50-year period. An evaluation of homogeneous recycle cores with elevated minor actinide contents is presented to illustrate the impact of using progressively higher TRU content on the core and transmutation performance, as a means of starting with known fuel technology with the aim of ultimately employing grouped TRU fuel in such cores. Reactivity coefficients and safety parameters are presented to indicate that the cores evaluated appear workable from a safety perspective, though more detailed safety and systems evaluations are required. (authors)

Recycling of Polymer-Based Multilayer Packaging: A Review

Directory of Open Access Journals (Sweden)

Katharina Kaiser

2017-12-01

Full Text Available Polymer-based multilayer packaging materials are commonly used in order to combine the respective performance of different polymers. By this approach, the tailored functionality of packaging concepts is created to sufficiently protect sensitive food products and thus obtain extended shelf life. However, because of their poor recyclability, most multilayers are usually incinerated or landfilled, counteracting the efforts towards a circular economy and crude oil independency. This review depicts the current state of the European multilayer packaging market and sketches the current end-of-life situation of postconsumer multilayer packaging waste in Germany. In the main section, a general overview of the state of research about material recycling of different multilayer packaging systems is provided. It is divided into two subsections, whereby one describes methods to achieve a separation of the different components, either by delamination or the selective dissolution–reprecipitation technique, and the other describes methods to achieve recycling by compatibilization of nonmiscible polymer types. While compatibilization methods and the technique of dissolution–reprecipitation are already extensively studied, the delamination of packaging has not been investigated systematically. All the presented options are able to recycle multilayer packaging, but also have drawbacks like a limited scope or a high expenditure of energy.

Current status of scrap metal recycling and reuse in USA and European countries

International Nuclear Information System (INIS)

Matsumoto, Akira

1997-01-01

Recycling and reuse of natural resources has become a global issue to be pursued, but less effective without voluntary efforts from the every industries and of the individuals. In Japan, recycling and reuse of the scrap metal from dismantling of the nuclear facilities are currently noticed as a promising option and the responsible government organizations just started activities to develope the system for enabling and encouraging the nuclear facility owners to recycle their waste. Coincidently, there have been many reports published recently, which inform successful results of the method and the activities of the international organizations for the same intention. Taking this opportunity, current trends of scrap metal recycling and reuse in the experienced countries are reviewed and the proposals from IAEA, EC and OECD/NEA on the relating issues are summarized and compared in this paper. (author)

Option Pricing using Realized Volatility

DEFF Research Database (Denmark)

Stentoft, Lars Peter

dynamics to be used for option pricing purposes in this framework, and we show that our model explains some of the mispricings found when using traditional option pricing models based on interdaily data. We then show explicitly that a Generalized Autoregressive Conditional Heteroskedastic model with Normal...... Inverse Gaussian distributed innovations is the corresponding benchmark model when only daily data is used. Finally, we perform an empirical analysis using stock options for three large American companies, and we show that in all cases our model performs significantly better than the corresponding...... benchmark model estimated on return data alone. Hence the paper provides evidence on the value of using high frequency data for option pricing purposes....

The potential environmental gains from recycling waste plastics: simulation of transferring recycling and recovery technologies to Shenyang, China.

Science.gov (United States)

Chen, Xudong; Xi, Fengming; Geng, Yong; Fujita, Tsuyoshi

2011-01-01

With the increasing attention on developing a low-carbon economy, it is necessary to seek appropriate ways on reducing greenhouse gas (GHG) emissions through innovative municipal solid waste management (MSWM), such as urban symbiosis. However, quantitative assessments on the environmental benefits of urban symbiosis, especially in developing countries, are limited because only a limited number of planned synergistic activities have been successful and it is difficult to acquire detailed inventory data from private companies. This paper modifies and applies a two-step simulation system and used it to assess the potential environmental benefits, including the reduction of GHG emissions and saving of fossil fuels, by employing various Japanese plastics recycling/energy-recovery technologies in Shenyang, China. The results showed that among various recycling/energy-recovery technologies, the mechanical waste plastics recycling technology, which produces concrete formwork boards (NF boards), has the greatest potential in terms of reducing GHG emissions (1.66 kg CO(2)e/kg plastics), whereas the technology for the production of refuse plastic fuel (RPF) has the greatest potential on saving fossil fuel consumption (0.77 kg ce/kg-plastics). Additional benefits can be gained by applying combined technologies that cascade the utilization of waste plastics. Moreover, the development of clean energy in conjunction with the promotion of new waste plastics recycling programs could contribute to additional reductions in GHG emissions and fossil fuel consumption. Copyright © 2010 Elsevier Ltd. All rights reserved.

Innovation in Sustainable Education and Entrepreneurship through the UKM Recycling Center Operations

Science.gov (United States)

Zain, Shahrom Md; Basri, Noor Ezlin Ahmad; Mahmood, Nur Ajlaa; Basri, Hassan; Yaacob, Mashitoh; Ahmad, Maisarah

2013-01-01

Sustainable education and entrepreneurship through practical learning activities are necessary for students in higher education institutions. Students must experience real situations to develop an attitude and personality of caring for the environment, and they can acquire entrepreneurship education by managing transactions with recyclables. The…

Direction of CRT waste glass processing: Electronics recycling industry communication

International Nuclear Information System (INIS)

Mueller, Julia R.; Boehm, Michael W.; Drummond, Charles

2012-01-01

Highlights: ► Given a large flow rate of CRT glass ∼10% of the panel glass stream will be leaded. ► The supply of CRT waste glass exceeded demand in 2009. ► Recyclers should use UV-light to detect lead oxide during the separation process. ► Recycling market analysis techniques and results are given for CRT glass. ► Academic initiatives and the necessary expansion of novel product markets are discussed. - Abstract: Cathode Ray Tube, CRT, waste glass recycling has plagued glass manufacturers, electronics recyclers and electronics waste policy makers for decades because the total supply of waste glass exceeds demand, and the formulations of CRT glass are ill suited for most reuse options. The solutions are to separate the undesirable components (e.g. lead oxide) in the waste and create demand for new products. Achieving this is no simple feat, however, as there are many obstacles: limited knowledge of waste glass composition; limited automation in the recycling process; transportation of recycled material; and a weak and underdeveloped market. Thus one of the main goals of this paper is to advise electronic glass recyclers on how to best manage a diverse supply of glass waste and successfully market to end users. Further, this paper offers future directions for academic and industry research. To develop the recommendations offered here, a combination of approaches were used: (1) a thorough study of historic trends in CRT glass chemistry; (2) bulk glass collection and analysis of cullet from a large-scale glass recycler; (3) conversations with industry members and a review of potential applications; and (4) evaluation of the economic viability of specific uses for recycled CRT glass. If academia and industry can solve these problems (for example by creating a database of composition organized by manufacturer and glass source) then the reuse of CRT glass can be increased.

Energy recycling: an innovative solution for unrecyclable plastic; Reciclagem energetica: uma solucao inovadora para o plastico nao reciclavel

Energy Technology Data Exchange (ETDEWEB)

Silva, Julyane Carolina; Oliveira, Magno Andre de; Pires, Pedro Henrique; Silva, Thuanye Peixoto; Rodrigues, Marcia [Centro Universitario de Belo Horizonte (UnBH), MG (Brazil)], e-mails: juhlorah@hotmail.com, marromar2004@yahoo.com.br

2011-07-01

This paper shows a new technology that is already used in over 35 countries with more than 750 plants in total and is still under study in Brazil: the energy recycling of plastic. Through studies, tables, comparisons and observations, have to analyze the plastic, chemical composition, the steps of material recycling and energy production, the final products obtained by recycling and gases released during the process. Thus, after highlighting how this technology is advantageous, it is expected to awaken to the reflection that it is feasible to use the recycling energy due to its great benefits environmental, social and economic shown the course of research. (author)

The generation of denatured reactor plutonium by different options of the fuel cycle

Energy Technology Data Exchange (ETDEWEB)

Broeders, C.H.M.; Kessler, G. [Inst. for Neutron Physics and Reactor Technology, Research Center Karlsruhe (Germany)

2006-11-15

Denatured (proliferation resistant) reactor plutonium can be generated in a number of different fuel cycle options. First denatured reactor plutonium can be obtained if, instead of low enriched U-235 PWR fuel, re-enriched U-235/U-236 from reprocessed uranium is used (fuel type A). Also the envisaged existing 2,500 t of reactor plutonium (being generated world wide up to the year 2010), mostly stored in intermediate fuel storage facilities at present, could be converted during a transition phase into denatured reactor plutonium by the options fuel type B and D. Denatured reactor plutonium could have the same safeguards standard as present low enriched (<20% U-235) LWR fuel. It could be incinerated by recycling once or twice in PWRs and subsequently by multi-recycling in FRs (CAPRA type or IFRs). Once denatured, such reactor plutonium could remain denatured during multiple recycling. In a PWR, e.g., denatured reactor plutonium could be destroyed at a rate of about 250 kg/GWey. While denatured reactor plutonium could be recycled and incinerated under relieved IAEA safeguards, neptunium would still have to be monitored by the IAEA in future for all cases in which considerable amounts of neptunium are produced. (orig.)

Feasibility Study on Nitrogen-15 Enrichment and Recycling System for Innovative FR Cycle System With Nitride Fuel

International Nuclear Information System (INIS)

Masaki Inoue; Kiyoshi Ono; Tsuna-aki Fujioka; Koji Sato; Takeo Asaga

2002-01-01

Highly-isotopically-enriched nitrogen (HE-N 2 ; 15 N abundance 99.9%) is indispensable for a nitride fueled fast reactor (FR) cycle to minimize the effect of carbon-14 ( 14 C) generated mainly by 14 N(n,p) 14 C reaction in the core on environmental burden. Thus, the development of inexpensive 15 N enrichment and recycling technology is one of the key aspects for the commercialization of a nitride fueled FR cycle. Nitrogen isotope separation by the gas adsorption technique was experimentally confirmed in order to obtain its technological perspective. A conventional pressure swing adsorption technique, which is already commercialized for recovering the nitrogen gas from multi-composition gas-mixture, would be suitable for recovering in both reprocessing and fuel fabrication to recycle the HE-N 2 gas. A couple of the nitride fuel cycle system concepts including the reprocessing and fuel fabrication process flow diagrams with the HE-N 2 gas recycling were newly designed for both aqueous and non-aqueous (pyrochemical) nitride fuel recycle plants, and also the effect of the HE-N 2 gas recycling on the economics of each concept was evaluated. (authors)

Understanding Eco-innovation and Green Business Models

DEFF Research Database (Denmark)

Andersen, Maj Munch

2014-01-01

Eco-innovation is considered a still more important competitive strategy to maintain production in highcost economies such as the Danish one. Within the studies of economics of technological change only little research has been undertaken on the dynamics of eco-innovation. Rigorous statistics...... technologies which has taken a starting pointin the environmental effects of varies technologies. The seven categories are:1. Curative eco-innovations - add-on (clean-up, recycling and resource handling)2. Integrated continuous process and product eco-innovations (cleaner production and products)3. User...... and definitions of ecoinnovationare lacking leading to much confusion and methodologically weak empirical analyses. This paperseeks to remedy this by offering a definition and taxonomy of eco-innovations and discussing theimplications for green business model thinking, bringing in examples of Danish successful...

U.S. Department of Energy National Center of Excellence for Metals Recycle

International Nuclear Information System (INIS)

Adams, V.; Bennett, M.; Bishop, L.

1998-06-01

The US Department of Energy (DOE) National Center of Excellence for Metals Recycle has recently been established. The vision of this new program is to develop a DOE culture that promotes pollution prevention by considering the recycle and reuse of metal as the first and primary disposition option and burial as a last option. The Center of Excellence takes the approach that unrestricted release of metal is the first priority because it is the most cost-effective disposition pathway. Where this is not appropriate, restricted release, beneficial reuse, and stockpile of ingots are considered. The Center has gotten off to a fast start. Current recycling activities include the sale of 40,000 tons of scrap metal from the East Tennessee Technology Park (formerly K-25 Plant) K-770 scrap yard, K-1064 surplus equipment and machinery, 7,000 PCB-contaminated drums, 12,000 tons of metal from the Y-12 scrap yard, and 1,000 metal pallets. In addition, the Center of Excellence is developing a toolbox for project teams that will contain a number of specific tools to facilitate metals recycle. This Internet-based toolbox will include primers, computer software, and case studies designed to help sites to perform life cycle analysis, perform ALARA (As Low As is Reasonably Achievable) analysis for radiation exposures, produce pollution prevention information and documentation, manage their materials inventory, produce independent government estimates, and implement sale/service contracts. The use of these tools is described for two current activities: disposition of scrap metal in the Y-12 scrap yard, and disposition of PCB-contaminated drums. Members of the Center look forward to working with all DOE sites, regulatory authorities, the private sector, and other stakeholders to achieve the metals recycle goals

The informal recycling in the international and local context: theoretical Elements

International Nuclear Information System (INIS)

Yepes P, Dora Luz

2002-01-01

This article is a synthesis of the theoretical aspects related with the urban problem of the informal recycling in our means, and it is framed inside the denominated investigation project alternatives for their invigoration of the informal recycling in Medellin, which is a thesis of the grade that looks for to strengthen the informal recycling through the study of the factors associated to the labor productivity of the informal recycle. Specifically, the study will identify options of improvement of its work y points to propose alternatives to dignify the labor of these people integrally by the light of environmental precepts, technicians, normative, institutional social and of sustainability. This document describe the theoretical elements in which this investigation will be based, showing the informal recycling inside of an international context, and their situation in a national and local environment. As a result of the bibliographical revision carried out, can be said, that it glimpses a low interest in to improve the conditions of work a International level of the informal recycle, unless the strategies that it outlines the international labor organization, with regard to the strengthening of the informal economy; in Latin America, it has not been possible to go further of the official rhetoric and the pro motion of the groups environmentalists, but in the issue of the recovery policies, reuse, and the recycling of solid wastes, if there. Has been a sustained advance; at national level clear strategies to improve the informal work of the recycle are being identified, however, lacks many efforts to develop the committed actions with these strategies, in spite of the fact that has been advancing the creation of recycle organizations little by little

COPPER CABLE RECYCLING TECHNOLOGY

International Nuclear Information System (INIS)

Chelsea Hubbard

2001-01-01

The United States Department of Energy (DOE) continually seeks safer and more cost-effective technologies for use in deactivation and decommissioning (D and D) of nuclear facilities. The Deactivation and Decommissioning Focus Area (DDFA) of the DOE's Office of Science and Technology (OST) sponsors large-scale demonstration and deployment projects (LSDDPs). At these LSDDPs, developers and vendors of improved or innovative technologies showcase products that are potentially beneficial to the DOE's projects and to others in the D and D community. Benefits sought include decreased health and safety risks to personnel and the environment, increased productivity, and decreased costs of operation. The Idaho National Engineering and Environmental Laboratory (INEEL) generated a list of statements defining specific needs and problems where improved technology could be incorporated into ongoing D and D tasks. One such need is to reduce the volume of waste copper wire and cable generated by D and D. Deactivation and decommissioning activities of nuclear facilities generates hundreds of tons of contaminated copper cable, which are sent to radioactive waste disposal sites. The Copper Cable Recycling Technology separates the clean copper from contaminated insulation and dust materials in these cables. The recovered copper can then be reclaimed and, more importantly, landfill disposal volumes can be reduced. The existing baseline technology for disposing radioactively contaminated cables is to package the cables in wooden storage boxes and dispose of the cables in radioactive waste disposal sites. The Copper Cable Recycling Technology is applicable to facility decommissioning projects at many Department of Energy (DOE) nuclear facilities and commercial nuclear power plants undergoing decommissioning activities. The INEEL Copper Cable Recycling Technology Demonstration investigated the effectiveness and efficiency to recycle 13.5 tons of copper cable. To determine the effectiveness

Use of recycled plastic in concrete: a review.

Science.gov (United States)

Siddique, Rafat; Khatib, Jamal; Kaur, Inderpreet

2008-01-01

Numerous waste materials are generated from manufacturing processes, service industries and municipal solid wastes. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. Solid waste management is one of the major environmental concerns in the world. With the scarcity of space for landfilling and due to its ever increasing cost, waste utilization has become an attractive alternative to disposal. Research is being carried out on the utilization of waste products in concrete. Such waste products include discarded tires, plastic, glass, steel, burnt foundry sand, and coal combustion by-products (CCBs). Each of these waste products has provided a specific effect on the properties of fresh and hardened concrete. The use of waste products in concrete not only makes it economical, but also helps in reducing disposal problems. Reuse of bulky wastes is considered the best environmental alternative for solving the problem of disposal. One such waste is plastic, which could be used in various applications. However, efforts have also been made to explore its use in concrete/asphalt concrete. The development of new construction materials using recycled plastics is important to both the construction and the plastic recycling industries. This paper presents a detailed review about waste and recycled plastics, waste management options, and research published on the effect of recycled plastic on the fresh and hardened properties of concrete. The effect of recycled and waste plastic on bulk density, air content, workability, compressive strength, splitting tensile strength, modulus of elasticity, impact resistance, permeability, and abrasion resistance is discussed in this paper.

Use of recycled plastic in concrete: A review

International Nuclear Information System (INIS)

Siddique, Rafat; Khatib, Jamal; Kaur, Inderpreet

2008-01-01

Numerous waste materials are generated from manufacturing processes, service industries and municipal solid wastes. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. Solid waste management is one of the major environmental concerns in the world. With the scarcity of space for landfilling and due to its ever increasing cost, waste utilization has become an attractive alternative to disposal. Research is being carried out on the utilization of waste products in concrete. Such waste products include discarded tires, plastic, glass, steel, burnt foundry sand, and coal combustion by-products (CCBs). Each of these waste products has provided a specific effect on the properties of fresh and hardened concrete. The use of waste products in concrete not only makes it economical, but also helps in reducing disposal problems. Reuse of bulky wastes is considered the best environmental alternative for solving the problem of disposal. One such waste is plastic, which could be used in various applications. However, efforts have also been made to explore its use in concrete/asphalt concrete. The development of new construction materials using recycled plastics is important to both the construction and the plastic recycling industries. This paper presents a detailed review about waste and recycled plastics, waste management options, and research published on the effect of recycled plastic on the fresh and hardened properties of concrete. The effect of recycled and waste plastic on bulk density, air content, workability, compressive strength, splitting tensile strength, modulus of elasticity, impact resistance, permeability, and abrasion resistance is discussed in this paper

Reprocessed uranium recycling: the ideal and the facts

International Nuclear Information System (INIS)

Comte, D.

1998-01-01

Commercial reprocessing of Light Water Reactor (LWR) spent fuel provides Reprocessed Uranium (RepU) and plutonium, both products containing a large amount of energy. As the gap, already quite large, between uranium consumption and production threatens to grow, these materials show today a strong strategic benefit, constituting a substantial and reliable source of supply for nuclear fuel manufacturing. RepU, which represents about 96% of recycled materials, can be used in all major types of nuclear power reactor currently in operation. This paper focuses on RepU recycling in LWRs, the feasibility of which is technically well established world-wide, and industrially demonstrated through experience gained within the COGEMA Group. Contrary to a commonly accepted assumption, which probably derives from natural uranium prices remaining for more than a decade at a low level which cannot be sustained into the future, recycling RepU can also bring strong economic benefits to the utilities. It generates savings on uranium procurement that exceed expenditures associated with storing and processing RepU. Thus, the use of this product is an attractive option. The strategic and economic benefits of recycling RepU will become compelling in the near future. Anticipating these needs, the COGEMA Group has developed capabilities to offer utilities the services covering all steps from reprocessing of spent fuel to fuel fabrication using RepU. (author)

Product Innovation with Lumpy Investment

NARCIS (Netherlands)

Chahim, M.; Grass, D.; Hartl, R.F.; Kort, P.M.

2012-01-01

Abstract: This paper considers a firm that has the option to undertake product innovations. For each product innovation the firm has to install a new production plant. We find that investments are larger and occur in a later stadium when more of the old capital stock needs to be scrapped. Moreover,

Radioactive Scrap Metal (RSM) recycling: A doe white paper

International Nuclear Information System (INIS)

Chatterjee, S.; Moore, H.H.; Ghoshal, A.

1992-01-01

An effective White Paper on recycling radioactive scrap metals has been drafted at the request of the U.S. Department of Energy (DOE) recently. The paper has received the praise and commendation of the DOE's Director of Environmental Management. However, obstructionist posturing by the petty bureaucrats in DOE continues to plague the meaningful implementation of RSM recycling. The key findings of the White Paper study and its major recommendations have discussed in this paper. The study indicates that several technologies, such as melt refining and electro refining, are currently available for surface and volume decontamination of metals. The unit cost of decontamination was found to vary from $700 to $400/ton; recycling of most low-contaminated metals can therefore be cost-effective vis-a vis the average cost of low-level radioactive wastes disposal of %400 to $2800/ton. Major recycling demonstration projects with emphasis on restricted RSM reuse options have been recommended. Volume contamination standard for unrestricted release should be established only after adequate studies of health effects and scientific/industrial effects of RSM reuse has been conducted by the Environmental Protection Agency (EPA) and the Nuclear Regulatory Commission (NRC). Some of the significant technical data developed during this study have also been briefly discussed in this paper. (author)

Recyclable epoxy resins: An example of green approach for advanced composite applications

Science.gov (United States)

Cicala, Gianluca; Rosa, Daniela La; Musarra, Marco; Saccullo, Giuseppe; Banatao, Rey; Pastine, Stefan

2016-05-01

Automotive composite applications are increasingly growing due to demand for lightweight structures to comply to the requirements for fuel reduction. HP-RTM is gaining relevance as one of the preferred production technologies for high volume applications. The BMW i3 life module being a notable example of HP-RTM application. The key aspects of HP-RTM are the short injection times (i.e. less than 1min) and the fast curing of the thermoset resins (i.e. less than 10min). The choice of using thermosets poses relevant issues for their limited recycling options. The standard recycling solution is the incineration but, this solution poses some concerns in terms of global environmental impact. Novel solutions are presented in this work based on the use of recyclable epoxy systems. In our work the results of experimentation carried out by our group with cleavable ammines by Connora Technologies and bioepoxy resins by Entropy Resins will be discussed. The multiple uses of recycled matrices obtained treating the recyclable epoxy resins are discussed in the framework of a "cradle" to "crave" approach. Finally, Life Cycle Assessment (LCA) is used to evaluate the environmental benefits of the proposed approach.

Options Study Documenting the Fast Reactor Fuels Innovative Design Activity

Energy Technology Data Exchange (ETDEWEB)

Jon Carmack; Kemal Pasamehmetoglu

2010-07-01

This document provides presentation and general analysis of innovative design concepts submitted to the FCRD Advanced Fuels Campaign by nine national laboratory teams as part of the Innovative Transmutation Fuels Concepts Call for Proposals issued on October 15, 2009 (Appendix A). Twenty one whitepapers were received and evaluated by an independent technical review committee.

Construction Waste Recycling Technologies: How to Define and Assess Their Economic, Environmental and Social Effects by the use of Input-Output Analysis

DEFF Research Database (Denmark)

Bozhilova-Kisheva, Kossara Petrova; Olsen, Stig Irving

2012-01-01

aggregates that due to the less quality are used mainly in road construction and less in buildings. Within the EU FP7 project Advanced Technologies for the Production of Cement and Clean Aggregates from Construction and Demolition Waste (C2CA), an innovative technology for CDW recycling to clean aggregates......Concrete is one of the most important building materials and it entails a big environmental impact making recycling relevant from an environmental perspective. Recycling of construction and demolition waste (CDW) containing concrete is being performed in the Netherlands resulting in recycled...

The importance of recycling - Responsible recycling

International Nuclear Information System (INIS)

Svensson, Joens Petter

2014-01-01

7 times the total emissions from Sweden are saved each year by the recycling industry. It reduces CO 2 emissions and saves the environment. In fact it annually reduces global CO 2 emissions by 500 million tons, which is more than what is being emitted by the world wide aviation industry. Recycling of iron and steel saves 74% energy and reduces water and air pollution by respectively 76% and 86%, compared to primary production. It provides new raw materials and contributes to save energy. There's no sense in producing goods in a permanent material like plastics, that's supposed to be used only once. It's a huge waste of resources. Today the recycling industry provides half of the world's raw materials and this figure is set to increase. It's about environmentally sound management of resources. It's about plain common sense. There has to be a political willingness to facilitate recycling in every way. And from a corporate perspective social responsibility is becoming an increasingly important competitive edge. This is also a communication issue, it has to be a fact that is well known to the market when a company is doing valuable environmental work. We also need a well functioning global market with easy to understand regulations to facilitate global trade. The global demand for recycled materials should influence their collection and use. Fraud and theft has also to be kept at bay which calls for a close collaboration between organizations such as The International Chamber of Commerce, The International Trade Council and the International Maritime Bureau of the commercial crime services. Increasing recycling is the only way to go if we want to minimize our effect on the environment. We have to remember that recycling is essential for the environment. An increase would be a tremendous help to reduce the green house effect. Increasing recycling is not rocket science. We know how to do it, we just have to decide to go through with it

Recycling Facilities - Land Recycling Cleanup Locations

Data.gov (United States)

NSGIC Education | GIS Inventory — Land Recycling Cleanup Location Land Recycling Cleanup Locations (LRCL) are divided into one or more sub-facilities categorized as media: Air, Contained Release or...

Assessment of Used Nuclear Fuel Inventory Relative to Disposition Options

International Nuclear Information System (INIS)

Wagner, John C.; Peterson, Joshua L.; Mueller, Don; Gehin, Jess C.; Worrall, Andrew; Taiwo, Temitope; Nutt, Mark; Williamson, Mark A.; Todosow, Mike; Wigeland, Roald; Halsey, William; Omberg, Ronald; Swift, Peter; Carter, Joe

2013-01-01

This paper presents a technical assessment of the current inventory [∼70,150 metric tons of heavy metal (MTHM) as of 2011] of U.S.-discharged used nuclear fuel (UNF) to support decisions regarding fuel cycle strategies and research, development and demonstration (RD and D) needs. The assessment considered discharged UNF from commercial nuclear electricity generation and defense and research programs and determined that the current UNF inventory can be divided into the following three categories: 1. Disposal - excess material that is not needed for other purposes; 2. Research - material needed for RD and D purposes to support waste management (e.g., UNF storage, transportation, and disposal) and development of alternative fuel cycles (e.g., separations and advanced fuels/reactors); and 3. Recycle/Recovery - material with inherent and/or strategic value. A set of key assumptions and attributes relative to the disposition options was used to categorize the current UNF inventory. Based on consideration of RD and D needs, time frames and material needs for deployment of alternative fuel cycles, characteristics of the current UNF inventory, and possible uses to support national security interests, it was determined that the vast majority of the category, without the need for retrieval for reuse or research purposes. Access to the material in the Research and Recycle/Recovery categories should be retained to support RD and D needs and national security interests. This assessment does not assume any decision about future fuel cycle options or preclude any potential options, including those with potential recycling of commercial UNF, since the ∼2,000 MTHM that is generated annually could provide the feedstock needed for deployment of alternative fuel cycles.

Nuclear recycling

International Nuclear Information System (INIS)

Spinrad, B.I.

1985-01-01

This paper discusses two aspects of the economics of recycling nuclear fuel: the actual costs and savings of the recycling operation in terms of money spent, made, and saved; and the impact of the recycling on the future cost of uranium. The authors review the relevant physical and chemical processes involved in the recycling process. Recovery of uranium and plutonium is discussed. Fuel recycling in LWRs is examined and a table presents the costs of reprocessing and not reprocessing. The subject of plutonium in fast reactors is addressed. Safeguards and weapons proliferation are discussed

Cellulase recycling in biorefineries--is it possible?

Science.gov (United States)

Gomes, Daniel; Rodrigues, Ana Cristina; Domingues, Lucília; Gama, Miguel

2015-05-01

On a near future, bio-based economy will assume a key role in our lives. Lignocellulosic materials (e.g., agroforestry residues, industrial/solid wastes) represent a cheaper and environmentally friendly option to fossil fuels. Indeed, following suitable processing, they can be metabolized by different microorganisms to produce a wide range of compounds currently obtained by chemical synthesis. However, due to the recalcitrant nature of these materials, they cannot be directly used by microorganisms, the conversion of polysaccharides into simpler sugars being thus required. This conversion, which is usually undertaken enzymatically, represents a significant part on the final cost of the process. This fact has driven intense efforts on the reduction of the enzyme cost following different strategies. Here, we describe the fundamentals of the enzyme recycling technology, more specifically, cellulase recycling. We focus on the main strategies available for the recovery of both the liquid- and solid-bound enzyme fractions and discuss the relevant operational parameters (e.g., composition, temperature, additives, and pH). Although the efforts from the industry and enzyme suppliers are primarily oriented toward the development of enzyme cocktails able to quickly and effectively process biomass, it seems clear by now that enzyme recycling is technically possible.

A principle and seven ambitions for innovation

International Nuclear Information System (INIS)

Lauvergeon, Anne; Verdier, Henri; Biot, Jacques; Bouyoux, Philippe; Demarolle, Alain; Erra, Mercedes; Haignere, Claudie; Lombard, Didier; Pisani-Ferry, Jean; Rousset, Alain; Serres, Michel; Aghion, Philippe; Bourdoncle, Francois; Caffier, Jean-Louis; Dufourcq, Nicolas; Fink, Mathias; Lehmann, Jean-Claude; Mandon, Thierry; Prieux, Pierre; Alain Sahel, Jose; Legait, Benoit; Faitot, Aurelie

2013-10-01

Published by the Commission for Innovation with the mission to identify and select a limited number of strong ambitions based on major innovations, in order to bring wealth and employment to France on the long term, the objective of this report is to stimulate innovation within enterprises of any size on sustainable priorities. After an analysis of the world context, the report identifies France's strengths and weaknesses, describes how to create an environment which is favourable to innovation, discusses how choices are made among the various possibilities and opportunities, and defines some principles for an innovating implementation. Seven ambitions are then proposed. They address energy storage, the recycling of rare materials, the valorisation of sea resources (metals, sea water desalination), vegetal proteins and vegetal chemistry, the development of customised medicine, the development of 'silver' economy or innovation to the service of longevity, and the valorisation of massive data (Big Data)

Residential Solar Photovoltaics: Comparison of Financing Benefits, Innovations, and Options

Energy Technology Data Exchange (ETDEWEB)

Speer, B.

2012-10-01

This report examines relatively new, innovative financing methods for residential photovoltaics (PV) and compares them to traditional self-financing. It provides policymakers with an overview of the residential PV financing mechanisms, describes relative advantages and challenges, and analyzes differences between them where data is available. Because these innovative financing mechanisms have only been implemented in a few locations, this report can inform their wider adoption.

Modelling Recycling Targets

DEFF Research Database (Denmark)

Hill, Amanda Louise; Leinikka Dall, Ole; Andersen, Frits M.

2014-01-01

Within the European Union (EU) a paradigm shift is currently occurring in the waste sector, where EU waste directives and national waste strategies are placing emphasis on resource efficiency and recycling targets. The most recent Danish resource strategy calculates a national recycling rate of 22......% for household waste, and sets an ambitious goal of a 50% recycling rate by 2020. This study integrates the recycling target into the FRIDA model to project how much waste and from which streams should be diverted from incineration to recycling in order to achieve the target. Furthermore, it discusses how...... the existing technological, organizational and legislative frameworks may affect recycling activities. The results of the analysis show that with current best practice recycling rates, the 50% recycling rate cannot be reached without recycling of household biowaste. It also shows that all Danish municipalities...

Unconventional recycling

Energy Technology Data Exchange (ETDEWEB)

White, K.M.

1996-05-01

Despite advances made in recycling technology and markets for materials over the past few years, recycling at convention centers, particularly on the show floor itself, can be a vexing problem. Part of the problem lies in the fact that recycling at convention centers has more to do with logistics than it does with these industry trends. However, given the varied nature of convention centers, and the shows they book, a rigid approach to recycling at convention centers is not always feasible. Like the numerous different curbside programs serving communities across the country, what works for one convention center--and one show--many not work for another. These difficulties notwithstanding, more convention centers are offering recycling programs today, and more groups booking conventions these days have begun requesting recycling services.

Recycling option search for a 600 MWE sodium-cooled transmutation fast reactor

Energy Technology Data Exchange (ETDEWEB)

Lee, Yong Kyo; Kim, Myung Hyun [Dept. of Nuclear Engineering, Kyung Hee University, Yongin (Korea, Republic of)

2015-02-15

Four recycling scenarios involving pyroprocessing of spent fuel (SF) have been investigated for a 600-MWe transmutation sodium-cooled fast reactor (SFR), KALIMER. Performance evaluation was done with code system REBUS connected with TRANSX and TWODANT. Scenario Number 1 is the pyroprocessing of Canada deuterium uranium (CANDU) SF. Because the recycling of CANDU SF does not have any safety problems, the CANDU-Pyro- SFR system will be possible if the pyroprocessing capacity is large enough. Scenario Number 2 is a feasibility test of feed SF from a pressurized water reactor PWR. The sensitivity of cooling time before prior to pyro-processing was studied. As the cooling time increases, excess reactivity at the beginning of the equilibrium cycle (BOEC) decreases, thereby creating advantageous reactivity control and improving the transmutation performance of minor actinides. Scenario Number 3 is a case study for various levels of recovery factors of transuranic isotopes (TRUs). If long-lived fission products can be separated during pyroprocessing, the waste that is not recovered is classified as low- and intermediate-level waste, and it is sufficient to be disposed of in an underground site due to very low-heat-generation rate when the waste cooling time becomes >300 years at a TRU recovery factor of 99.9%. Scenario Number 4 is a case study for the recovery factor of rare earth (RE) isotopes. The RE isotope recovery factor should be lowered to 20% in order to make sodium void reactivity less than <7$, which is the design limit of a metal fuel.

Recycling option search for a 600-MWe sodium-cooled transmutation fast reactor

Directory of Open Access Journals (Sweden)

Yong Kyo Lee

2015-02-01

Full Text Available Four recycling scenarios involving pyroprocessing of spent fuel (SF have been investigated for a 600-MWe transmutation sodium-cooled fast reactor (SFR, KALIMER. Performance evaluation was done with code system REBUS connected with TRANSX and TWODANT. Scenario Number 1 is the pyroprocessing of Canada deuterium uranium (CANDU SF. Because the recycling of CANDU SF does not have any safety problems, the CANDU-Pyro-SFR system will be possible if the pyroprocessing capacity is large enough. Scenario Number 2 is a feasibility test of feed SF from a pressurized water reactor PWR. The sensitivity of cooling time before prior to pyro-processing was studied. As the cooling time increases, excess reactivity at the beginning of the equilibrium cycle (BOEC decreases, thereby creating advantageous reactivity control and improving the transmutation performance of minor actinides. Scenario Number 3 is a case study for various levels of recovery factors of transuranic isotopes (TRUs. If long-lived fission products can be separated during pyroprocessing, the waste that is not recovered is classified as low- and intermediate-level waste, and it is sufficient to be disposed of in an underground site due to very low-heat-generation rate when the waste cooling time becomes >300 years at a TRU recovery factor of 99.9%. Scenario Number 4 is a case study for the recovery factor of rare earth (RE isotopes. The RE isotope recovery factor should be lowered to ≤20% in order to make sodium void reactivity less than <7$, which is the design limit of a metal fuel.

Some material and construction aspects regarding in situ recycling of road pavements in South Africa

CSIR Research Space (South Africa)

Paige-Green, P

2006-07-01

Full Text Available In situ recycling as a pavement rehabilitation option in South Africa is becoming increasingly important. Use has been made of both bitumen (emulsion and foamed) and traditional chemical stabilizers (lime, cement, lime/slagment, etc). Very little...

Recycling Lesson Plan

Science.gov (United States)

Okaz, Abeer Ali

2013-01-01

This lesson plan designed for grade 2 students has the goal of teaching students about the environmental practice of recycling. Children will learn language words related to recycling such as: "we can recycle"/"we can't recycle" and how to avoid littering with such words as: "recycle paper" and/or "don't throw…

Parametric analyses of single-zone thorium-fueled molten salt reactor fuel cycle options

International Nuclear Information System (INIS)

Powers, J.J.; Worrall, A.; Gehin, J.C.; Harrison, T.J.; Sunny, E.E.

2013-01-01

Analyses of fuel cycle options based on thorium-fueled Molten Salt Reactors (MSRs) have been performed in support of fuel cycle screening and evaluation activities for the United States Department of Energy. The MSR options considered are based on thermal spectrum MSRs with 3 different separations levels: full recycling, limited recycling, and 'once-through' operation without active separations. A single-fluid, single-zone 2250 MWth (1000 MWe) MSR concept consisting of a fuel-bearing molten salt with graphite moderator and reflectors was used as the basis for this study. Radiation transport and isotopic depletion calculations were performed using SCALE 6.1 with ENDF/B-VII nuclear data. New methodology developed at Oak Ridge National Laboratory (ORNL) enables MSR analysis using SCALE, modeling material feed and removal by taking user-specified parameters and performing multiple SCALE/TRITON simulations to determine the resulting equilibrium operating conditions. Parametric analyses examined the sensitivity of the performance of a thorium MSR to variations in the separations efficiency for protactinium and fission products. Results indicate that self-sustained operation is possible with full or limited recycling but once-through operation would require an external neutron source. (authors)

Public opinion on water reuse options

International Nuclear Information System (INIS)

Bruvold, W.H.

1988-01-01

Public policy on waste water reuse options must be informed by public opinion because it is the public who must pay the cost of developing the option and who will be served by the option in the future. For public policy on reuse, guidance for innovative reuse is not as simple as first believed. It seems that public opinion regarding actual community reuse options is affected by the linkage of several factors, including water conservation, health protection, treatment and distribution costs, and environmental enhancement. Probability sampling was used in 7 studies to select respondents who were queried regarding their opinions on various reclaimed water uses such as ranging from cooling tower water to full domestic use. These 7 are briefly reviewed

FEASIBILITY OF RECYCLING PLUTONIUM AND MINOR ACTINIDES IN LIGHT WATER REACTORS USING HYDRIDE FUEL

International Nuclear Information System (INIS)

Greenspan, Ehud; Todreas, Neil; Taiwo, Temitope

2009-01-01

The objective of this DOE NERI program sponsored project was to assess the feasibility of improving the plutonium (Pu) and minor actinide (MA) recycling capabilities of pressurized water reactors (PWRs) by using hydride instead of oxide fuels. There are four general parts to this assessment: (1) Identifying promising hydride fuel assembly designs for recycling Pu and MAs in PWRs; (2) Performing a comprehensive systems analysis that compares the fuel cycle characteristics of Pu and MA recycling in PWRs using the promising hydride fuel assembly designs identified in Part 1 versus using oxide fuel assembly designs; (3) Conducting a safety analysis to assess the likelihood of licensing hydride fuel assembly designs; and (4) Assessing the compatibility of hydride fuel with cladding materials and water under typical PWR operating conditions Hydride fuel was found to offer promising transmutation characteristics and is recommended for further examination as a possible preferred option for recycling plutonium in PWRs

FEASIBILITY OF RECYCLING PLUTONIUM AND MINOR ACTINIDES IN LIGHT WATER REACTORS USING HYDRIDE FUEL

Energy Technology Data Exchange (ETDEWEB)

Greenspan, Ehud; Todreas, Neil; Taiwo, Temitope

2009-03-10

The objective of this DOE NERI program sponsored project was to assess the feasibility of improving the plutonium (Pu) and minor actinide (MA) recycling capabilities of pressurized water reactors (PWRs) by using hydride instead of oxide fuels. There are four general parts to this assessment: 1) Identifying promising hydride fuel assembly designs for recycling Pu and MAs in PWRs 2) Performing a comprehensive systems analysis that compares the fuel cycle characteristics of Pu and MA recycling in PWRs using the promising hydride fuel assembly designs identified in Part 1 versus using oxide fuel assembly designs 3) Conducting a safety analysis to assess the likelihood of licensing hydride fuel assembly designs 4) Assessing the compatibility of hydride fuel with cladding materials and water under typical PWR operating conditions Hydride fuel was found to offer promising transmutation characteristics and is recommended for further examination as a possible preferred option for recycling plutonium in PWRs.

Waste material recycling: Assessment of contaminants limiting recycling

DEFF Research Database (Denmark)

Pivnenko, Kostyantyn

systematically investigated. This PhD project provided detailed quantitative data following a consistent approach to assess potential limitations for the presence of chemicals in relation to material recycling. Paper and plastics were used as illustrative examples of materials with well-established recycling...... schemes and great potential for increase in recycling, respectively. The approach followed in the present work was developed and performed in four distinct steps. As step one, fractional composition of waste paper (30 fractions) and plastics (9 fractions) from households in Åbenrå municipality (Southern...... detrimental to their recycling. Finally, a material flow analysis (MFA) approach revealed the potential for accumulation and spreading of contaminants in material recycling, on the example of the European paper cycle. Assessment of potential mitigation measures indicated that prevention of chemical use...

Does WEEE recycling make sense from an environmental perspective?

International Nuclear Information System (INIS)

Hischier, R.; Waeger, P.; Gauglhofer, J.

2005-01-01

The production of electrical and electronic equipment (EEE) is one of the fastest growing markets in the world. At the same time this also means that the amount of waste electrical and electronic equipment (WEEE) will continue to increase in the coming decades. As it is crucial to obtain more knowledge about the environmental consequences of the different WEEE treatment options, a study examining the two Swiss take-back and recycling systems of SWICO (for computers, consumer electronics and telecommunication equipment) and S.EN.S (household appliances) has been conducted. The two systems, which are based on an advanced recycling fee, are well established within Switzerland. With a combined approach of material flow analysis (MFA) and life cycle assessment (LCA), the environmental impacts of these two systems have been estimated, including all further treatment steps, which transform the fractions either into secondary materials or into waste for final disposal. As a baseline, we have used a scenario assuming that no WEEE is recycled and hence only primary production for the similar amount of raw materials. The impact assessment is based on characterization factors according to the Dutch CML methodology. The results show that throughout the complete recycling chain the sorting and dismantling activities of companies are of minor interest; instead the main impact occurs during the treatment applied further downstream to turn the waste into secondary raw materials. Within the two systems in Switzerland, the collection of WEEE seems much more relevant than the sorting and dismantling activities. When comparing the environmental impact of WEEE recycling with that derived from the baseline scenario (incineration of all WEEE and primary production of the raw materials), WEEE recycling proves to be clearly advantageous from an environmental perspective

Long-term issues associated with spent nuclear power fuel management options

International Nuclear Information System (INIS)

Jae-Sol, Lee; Kosaku, Fukuda; Burcl, R.; Bell, M.

2003-01-01

Spent fuel management is perceived as one of the crucial issues to be resolved for sustainable utilisation of nuclear power. In the last decades, spent fuel management policies have shown diverging tendencies among the nuclear power production countries - a group has adhered to reprocessing- recycle and another has turned to direct disposal, while the rest of the countries have not taken decision yet, often with ''wait and see'' position. Both the closed and open fuel cycle options for spent fuel management have been subject to a number of debates with pros and cons on various issues such as proliferation risk, environmental impact, etc. The anticipation for better technical solutions that would mitigate those issues has given rise to the renewal of interest in partitioning and transmutation of harmful nuclides to be disposed of, and in a broader context, the recent initiatives for development of innovative nuclear systems. The current trend toward globalization of market economy, which has already brought important impacts on nuclear industry, might have a stimulating effect on regional-international co-operations for cost-effective efforts to mitigate some of those long-term issues associated with spent fuel management. (author)

HEAVY METALS IN RECOVERED FINES FOR CONSTRUCTION AND DEMOLITION DEBRIS RECYCLING FACILITIES IN FLORIDA

Science.gov (United States)

A major product recovered from the processing and recycling of construction and demolition (C&D) debris is screened soil, also referred to as fines. A proposed reuse option for C&D debris fines is fill material, typically in construction projects as a substitute for natural soil....

Minor actinide transmutation - a waste management option

International Nuclear Information System (INIS)

Koch, L.

1986-01-01

The incentive to recycle minor actinides results from the reduction of the long-term α-radiological risk rather than from a better utilization of the uranium resources. Nevertheless, the gain in generated electricity by minor actinide transmutation in a fast breeder reactor can compensate for the costs of their recovery and make-up into fuel elements. Different recycling options of minor actinides are discussed: transmutation in liquid metal fast breeder reactors (LMFBRs) is possible as long as plutonium is not recycled in light water reactors (LWRs). In this case a minor actinide burner with fuel of different composition has to be introduced. The development of appropriate minor actinide fuels and their properties are described. The irradiation experiments underway or planned are summarized. A review of minor actinide partitioning from the PUREX waste stream is given. From the present constraints of LMFBR technology a reduction of the long-term α-radiological risk by a factor of 200 is deduced relative to that from the direct storage of spent LWR fuel. Though the present accumulation of minor actinides is low, nuclear transmutation may be needed when nuclear energy production has grown. (orig.)

Open-loop recycling: A LCA case study of PET bottle-to-fibre-recycling

NARCIS (Netherlands)

Shen, L.; Worrell, E.; Patel, M.K.

2010-01-01

This study assesses the environmental impact of polyethylene terephthalate (PET) bottle-to-fibre recycling using the methodology of life-cycle assessment (LCA). Four recycling cases, including mechanical recycling, semi-mechanical recycling, back-to-oligomer recycling and back-to-monomer recycling

Analysis of fuel options for the breakeven core configuration of the Advanced Recycling Reactor

Energy Technology Data Exchange (ETDEWEB)

Stauff, N.E.; Klim, T.K.; Taiwo, T.A. [Argonne National Laboratory, Argonne, IL (United States); Fiorina, C. [Politecnico di Milano, Milan (Italy); Franceschini, F. [Westinghouse Electric Company LLC., Cranberry Township, Pennsylvania (United States)

2013-07-01

A trade-off study is performed to determine the impacts of various fuel forms on the core design and core physics characteristics of the sodium-cooled Toshiba- Westinghouse Advanced Recycling Reactor (ARR). The fuel forms include oxide, nitride, and metallic forms of U and Th. The ARR core configuration is redesigned with driver and blanket regions in order to achieve breakeven fissile breeding performance with the various fuel types. State-of-the-art core physics tools are used for the analyses. In addition, a quasi-static reactivity balance approach is used for a preliminary comparison of the inherent safety performances of the various fuel options. Thorium-fueled cores exhibit lower breeding ratios and require larger blankets compared to the U-fueled cores, which is detrimental to core compactness and increases reprocessing and manufacturing requirements. The Th cores also exhibit higher reactivity swings through each cycle, which penalizes reactivity control and increases the number of control rods required. On the other hand, using Th leads to drastic reductions in void and coolant expansion coefficients of reactivity, with the potential for enhancing inherent core safety. Among the U-fueled ARR cores, metallic and nitride fuels result in higher breeding ratios due to their higher heavy metal densities. On the other hand, oxide fuels provide a softer spectrum, which increases the Doppler effect and reduces the positive sodium void worth. A lower fuel temperature is obtained with the metallic and nitride fuels due to their higher thermal conductivities and compatibility with sodium bonds. This is especially beneficial from an inherent safety point of view since it facilitates the reactor cool-down during loss of power removal transients. The advantages in terms of inherent safety of nitride and metallic fuels are maintained when using Th fuel. However, there is a lower relative increase in heavy metal density and in breeding ratio going from oxide to metallic

Paper waste - Recycling, incineration or landfilling? A review of existing life cycle assessments

International Nuclear Information System (INIS)

Villanueva, A.; Wenzel, H.

2007-01-01

A review of existing life cycle assessments (LCAs) on paper and cardboard waste has been undertaken. The objectives of the review were threefold. Firstly, to see whether a consistent message comes out of published LCA literature on optimum disposal or recycling solutions for this waste type. Such message has implications for current policy formulation on material recycling and disposal in the EU. Secondly, to identify key methodological issues of paper waste management LCAs, and enlighten the influence of such issues on the conclusions of the LCA studies. Thirdly, in light of the analysis made, to discuss whether it is at all valid to use the LCA methodology in its current development state to guide policy decisions on paper waste. A total of nine LCA studies containing altogether 73 scenarios were selected from a thorough, international literature search. The selected studies are LCAs including comparisons of different management options for waste paper. Despite claims of inconsistency, the LCAs reviewed illustrate the environmental benefits in recycling over incineration or landfill options, for paper and cardboard waste. This broad consensus was found despite differences in geographic location and definitions of the paper recycling/disposal systems studied. A systematic exploration of the LCA studies showed, however, important methodological pitfalls and sources of error, mainly concerning differences in the definition of the system boundaries. Fifteen key assumptions were identified that cover the three paper cycle system areas: raw materials and forestry, paper production, and disposal/recovery. It was found that the outcome of the individual LCA studies largely depended on the choices made in some of these assumptions, most specifically the ones concerning energy use and generation, and forestry

Going for increased recycling. A social cost-benefit analysis; Inzetten op meer recycling. Een maatschappelijke kosten-batenanalyse

Energy Technology Data Exchange (ETDEWEB)

Warringa, G.E.A.; De Bruyn, M.; Bijleveld, M.M.

2013-05-15

While the environmental benefits of scenarios geared to increased recycling have been convincingly demonstrated by previous studies, the question arises whether such scenarios bring economic benefits, too. This study therefore assesses the main economic effects of increased recycling in the Netherlands, providing data that can be used to advance policy development in this area. To address the main issue we performed a social cost-benefit analysis (SCBA), a welfare-theory-based tool that can be used to chart the full range of economic impacts ('welfare impacts') of a project or policy intervention. In doing so, a broad definition of welfare is adopted, encompassing not only financial and economic consequences, but also environmental and employment impacts and so on. Using SimaPro, all the environmental interventions inventoried (including energy consumption, transport and recycling process emissions) were assessed for each individual material flow, with impacts being expressed as far as possible in monetary terms to enable comparison. The main social costs of increased recycling are the higher costs for local authorities associated with separate waste collection. There is also reduced revenue for waste incinerators, because more waste will need to be imported from abroad. Finally, there are the policy costs of incentives for increased recycling and extra efforts to induce citizens to separate their waste. The latter costs were not quantified. Over and against these costs are positive welfare impacts. The main benefits are environmental, expressed monetarily in the present study in terms of avoided damage costs for society as a whole and avoided measures for securing government reduction targets. In addition, the separated waste has a value, reflected in lower processing costs. Increased recycling also creates new jobs, while recycling firms generate more profit than waste incinerators. Finally, there are the benefits accruing from greater innovation and

Knowledge, attitudes and behaviour regarding waste management options in Romania: results from a school questionnaire

Directory of Open Access Journals (Sweden)

Karin KOLBE

2014-12-01

The analysis revealed that knowledge is highly developed in Romania regarding the potential of recycling, while the concepts of waste management technologies are far less known about and understood. Landfill is seen as a problem for human health and the environment. However, recycling behaviour is low - partly as a result of limited possibilities. In general, the treatment hierarchy that is recommended in the "European waste hierarchy" is only partly reflected in students’ attitudes towards waste management options.

Chemical decontamination of process equipment using recyclable chelating solvent Phase I. Final report, September 1993--June 1995

International Nuclear Information System (INIS)

1995-10-01

The Department of Energy (DOE) is now faced with the task of meeting decontamination and decommissioning obligations at numerous facilities by the year 2019. Due to the tremendous volume of material involved, innovative decontamination technologies are being sought that can reduce the volumes of contaminated waste materials and secondary wastes requiring disposal. With sufficient decontamination, some of the material from DOE facilities could be released as scrap into the commercial sector for recycle, thereby reducing the volume of radioactive waste requiring disposal. Although recycling may initially prove to be more costly than current disposal practices, rapidly increasing disposal costs are expected to make recycling more and more cost effective. Additionally, recycling is now perceived as the ethical choice in a world where the consequences of replacing resources and throwing away reusable materials are impacting the well-being of the environment

Behaviour of Recycled Coarse Aggregate Concrete: Age and Successive Recycling

Science.gov (United States)

Sahoo, Kirtikanta; Pathappilly, Robin Davis; Sarkar, Pradip

2016-06-01

Recycled Coarse Aggregate (RCA) concrete construction technique can be called as `green concrete', as it minimizes the environmental hazard of the concrete waste disposal. Indian standard recommends target mean compressive strength of the conventional concrete in terms of water cement ratio ( w/ c). The present work is an attempt to study the behaviour of RCA concrete from two samples of parent concrete having different age group with regard to the relationship of compressive strength with water cement ratios. Number of recycling may influence the mechanical properties of RCA concrete. The influence of age and successive recycling on the properties such as capillary water absorption, drying shrinkage strain, air content, flexural strength and tensile splitting strength of the RCA concrete are examined. The relationship between compressive strength at different w/ c ratios obtained experimentally is investigated for the two parameters such as age of parent concrete and successive recycling. The recycled concrete using older recycled aggregate shows poor quality. While the compressive strength reduces with successive recycling gradually, the capillary water absorption increases abruptly, which leads to the conclusion that further recycling may not be advisable.

Shifting Cultivation : Promoting Innovative Policy and Development ...

International Development Research Centre (IDRC) Digital Library (Canada)

Shifting Cultivation : Promoting Innovative Policy and Development Options in the Eastern Himalayas. Shifting ... pressure and market forces. The idea is to share good policies and practices related to shifting cultivation and alternative options through regional exchange. ... Les chaînes de valeur comme leviers stratégiques.

Pilot trial on separation conditions for diaper recycling.

Science.gov (United States)

Kim, Kyung-Shin; Cho, Hee-Sun

2017-09-01

By utilizing laboratory-scale tests, the optimal separation conditions for diaper recycling were identified, and then, these conditions were validated by a pilot trial. In this research, we determined the mass balances derived during various processing steps and identified the most feasible procedures to use for separating each material in the output flow. The results showed that drum screening was not able to remove all the fiber and super absorbent particles (SAP) in the plastic-rich fraction and that cellulose enzyme treatment can be a good solution. To achieve better separation of fibers and SAP, slot screening followed by a cleaner is a potential option. A feasible diaper recycling process was recommended based on these results. This process involves screening and enzymatic treatment for the plastic fraction, and screening, cleaning, and thickening for the fiber fraction. Treatment procedures were also proposed for the SAP fraction and rejected materials. Copyright © 2017. Published by Elsevier Ltd.

Analysis of transition to fuel cycle system with continuous recycling in fast and thermal reactors - 5060

International Nuclear Information System (INIS)

Passereini, S.; Feng, B.; Fei, T.; Kim, T.K.; Taiwo, T.A.; Brown, N.R.; Cuadra, A.

2015-01-01

A recent Evaluation and Screening study of nuclear fuel cycle options identified a few groups of options as most promising. One of these most promising Evaluation Groups (EGs) is characterized by the continuous recycling of uranium (U) and transuranics (TRU) with natural uranium feed in both fast and thermal critical reactors. This evaluation group, designated as EG30, is represented by an example fuel cycle option that employs a two-technology, two-stage fuel cycle system. The first stage involves the continuous recycling of co-extracted U/TRU in Sodium-cooled Fast Reactors (SFRs) with metallic fuel and breeding ratio greater than 1. The second stage involves the use of the surplus TRU in Mixed Oxide (MOX) fuel in Pressurized Water Reactors that are MOX-capable (MOX-PWRs). This paper presents and discusses preliminary fuel cycle analysis results from the fuel cycle codes VISION and DYMOND for the transition to this fuel cycle option from the current once-through cycle in the United States (U.S.) that consists of Light Water Reactors (LWRs) that only use conventional UO 2 fuel. The analyses in this paper are applicable for a constant 100 GWe capacity, roughly the size of the U.S. nuclear fleet. Two main strategies for the transition to EG30 were analyzed: 1) deploying both SFRs and MOX-PWRs in parallel or 2) deploying them in series with the SFR fleet first. With an estimated retirement schedule for the existing LWRs, an assumed reactor lifetime of 60 years, and no growth, the nuclear system fully transitions to the new fuel cycle within 100 years for both strategies without SFR fuel shortages. Compared to the once-through cycle, transition to the SFR/MOX-PWR fleet with continuous recycle was shown to offer significant reductions in uranium consumption and waste disposal requirements. In addition, these initial calculations revealed a few notable modeling and strategy questions regarding how recycled resources are allocated, reactors that can switch between

Innovative process routes for a high-quality concrete recycling.

Science.gov (United States)

Menard, Y; Bru, K; Touze, S; Lemoign, A; Poirier, J E; Ruffie, G; Bonnaudin, F; Von Der Weid, F

2013-06-01

This study presents alternative methods for the processing of concrete waste. The mechanical stresses needed for the embrittlement of the mortar matrix and further selective crushing of concrete were generated by either electric impulses or microwaves heating. Tests were carried out on lab-made concrete samples representative of concrete waste from concrete mixer trucks and on concrete waste collected on a French demolition site. The results obtained so far show that both techniques can be used to weaken concrete samples and to enhance aggregate selective liberation (that is the production of cement paste-free aggregates) during crushing and grinding. Electric pulses treatment seems to appear more efficient, more robust and less energy consuming (1-3 kWh t(-1)) than microwave treatment (10-40 kWh t(-1)) but it can only be applied on samples in water leading to a major drawback for recycling aggregates or cement paste in the cement production process. Copyright © 2013 Elsevier Ltd. All rights reserved.

Tradeoffs in fuel cycle performance for most promising options - 15346

International Nuclear Information System (INIS)

Taiwo, T.; Kim, T.K.; Feng, B.; Stauff, N.; Hoffman, E.; Ganda, F.; Todosow, M.; Brown, N.; Raitses, G.; Gehin, J.; Powers, J.; Youinou, G.; Hiruta, H.; Wigeland, R.

2015-01-01

A recent Evaluation and Screening (E/S) study of nuclear fuel cycle options was conducted by grouping all potential options into 40 Evaluation Groups (EGs) based on similarities in fundamental physics characteristics and fuel cycle performance. Through a rigorous evaluation process considering benefit and challenge metrics, 4 of these EGs were identified by the E/S study as 'most promising'. All 4 involve continuous recycle of U/Pu or U/TRU with natural uranium feed in fast critical reactors. However, these most promising EGs also include fuel cycle groups with variations on feed materials, neutron spectra, and reactor criticality. Therefore, the impacts of the addition of natural thorium fuel feed to a system that originally only used natural uranium fuel feed, using an intermediate spectrum instead of a fast spectrum, and using externally-driven systems versus critical reactors were evaluated. It was found that adding thorium to the natural uranium feed mixture leads to lower burnup, higher mass flows, and degrades fuel cycle benefit metrics (waste management, resource utilization, etc.) for fuel cycles that continuously recycle U/Pu or U/TRU. Adding thorium results in fissions of 233 U instead of just 239 Pu and in turn results in a lower average number of neutrons produced per absorption (η) for the fast reactor system. For continuous recycling systems, the lower η results in lower excess reactivity and subsequently lower achievable fuel burnup. This in turn leads to higher mass flows (fabrication, reprocessing, disposal, etc.) to produce a given amount of energy and subsequent lower metrics performance. The investigated fuel cycle options with intermediate spectrum reactors also exhibited degraded performance in the benefit metrics compared to fast spectrum reactors. Similarly, this is due to lower η values as the spectrum softens. The best externally-driven systems exhibited similar performance as fast critical reactors in terms of mass flows

Educating T-Shaped professionals to meet substitution challenges and developing business models for substitution and recycling

Science.gov (United States)

Arroyo, Ana; Mendibil Eguiluz, Javier; Sánchez Cupido, Laura

2018-03-01

One strategy to overcome the challenges related to critical raw materials (CRMs) is their substitution and recycling. However, the bright scientific idea, proof of concept or laboratory demonstration need to cross the valley of death in order to become stated as ‘a substitute’ instead of ‘a potential substitute’. Most PhD students and Post Docs specialize within a given thematic area; for example on specific materials or on substitution in a certain application. This specialization could limit the ability to generate innovations and profitable business models if there are not enough tools and skills to transform new knowledge and research results into an appealing value proposition towards customers and to a business opportunity for the current markets. The project proposes a framework for developing substitution and recycling related cross-sectorial skills and tools. These are applied for training business-related competences e.g. teamwork, management, communication, value proposition and business models design, especially within RTOs and industries. The proposed learning itinerary can radically improve the path from scientific proof of concept into innovation and lean start up or industrial market launch. The developed framework is tested by a pilot group having several topics within the areas of substitution and recycling of critical raw materials.

Solvent recycle/contaminant reduction testing - Phase I, Task 3. Topical progress report, June 1994--December 1994

International Nuclear Information System (INIS)

1995-07-01

The Department of Energy (DOE) is now faced with the task of meeting decontamination and decommissioning obligations at numerous facilities by the year 2019. Due to the tremendous volume of material involved, innovative decontamination technologies are being sought that can reduce the volumes of contaminated waste materials and secondary wastes requiring disposal. With sufficient decontamination, some of the material from DOE facilities could be released as scrap into the commercial sector for recycle, thereby reducing the volume of radioactive waste requiring disposal. Although recycling may initially prove to be more costly than current disposal practices, rapidly increasing disposal costs are expected to make recycling more and more cost effective. Additionally, recycling is now perceived as the ethical choice in a world where the consequences of replacing resources and throwing away reusable materials are impacting the well-being of the environment. This report describes the solvent recyle test program for EDTA/ammonium carbonate solvent

Integrating recycling, renewable energy and agriculture for commercial waste to wealth businesses

International Nuclear Information System (INIS)

Gan Khai Chung; Angeline Pang

2010-01-01

Recycling organic material to produce renewable energy and organic fertilizer is an attractive business model in waste to wealth business proposition. Azed Bina Sdn Bhd has developed an integrated recycling facility to recycle solid organic materials into energy and organic fertilizer, a project partially funded by MOSTI TechnoFund in 2008. The novel and innovative aspect is the water disassociation technology which separates the water into hydrogen gas and oxygen gas economically using thermal heat from the burning of biomass which is a waste material. This system is modular, scalable, economical and environmental friendly. It has many applications in the field of, Environment and Solid Waste Management - recycling organic waste into energy and organic fertilizer rather than disposal at the landfill, hence preserving our environment. Green technology - economical biogas production consists of 50% hydrogen gas which is a clean and renewable energy source. The biogas has many applications in the food industry, manufacturing industry and agriculture sector. Agro-based industry - production of clean heat energy is useful for the drying of agriculture crops. Agriculture Sector - production of ash can be used to produce organic fertilizer by incorporating effective microbes. Reduce the dependence on chemical fertilizer which is bad for the environment Rural Development - developing rural area by integrating small scale industries, agro based industry, agriculture and rural area. The company commercial applications of recycling organic materials to produce energy for companies such as laundry business, agro based food drying and waste management recycling. The next project is to provide chilled water using organic waste. (author)

Innovation in China

DEFF Research Database (Denmark)

MacDonald, Greg; Yow, Yit-Seng; Li, Xing

China's economy is growing quickly, and is innovation-led.  Europe can relate to China through joint R&D, programmes which offer an alternative vehicle of engagement to the traditional political and economic approaches. Innovation in China: The Dawning of the Asian Century promotes an awareness...... of the dynamics of innovation in China. It examines Chinese and European approaches to science and technology and contends that the ‘rules for survival' in R&D and education are changing in favour of China, in terms of base R&D parameters such as research expenditure, scientists trained, papers published...... and patents awarded. The authors recommend options for Europe and China to connect through longitudinal R&D  projects and ‘carrousel-training exchanges' in environmental and health related fields....

Nuclear fuel cycle in France: today's situation and long term options

International Nuclear Information System (INIS)

Boullis, B.; Drevon, C.; Pays, M.

2015-01-01

In France plutonium and uranium are recycled as MOX fuel (used in 22 reactors) and URE (enriched uranium from spent fuel). Fission products and minor actinides, that composed ultimate wastes, are vitrified and cast in stainless steel containers. Fuel recycling has reached industrial maturity and about 30.000 tonnes of spent fuels have been processed. This strategy has allowed France to save about 17% of its annual consumption of uranium and to get a least volume of high-level radioactive wastes. This strategy can be pushed forwards by introducing a multi-recycling option in which plutonium and uranium from spent MOX fuels are recycled. Multi-recycling produces a nuclear fuel that is polluted with remainders of actinides and fission products and to compensate this deterioration of its neutronic properties a higher concentration of fissile materials is required. For safety reasons the concentration of plutonium in MOX fuels is limited to 12% so multi-recycling is not a strategy for a fleet of PWRs only. Fast neutron reactors use uranium and plutonium in a more efficiently way and can be a solution for multi-recycling. The study shows that for a constant output of 420 TWh a year a fleet of PWRs need 7600 tonnes of natural uranium. If mono-recycling is allowed this consumption decreases to 6300 tonnes a year and if multi-recycling is allowed by integrating fast reactors in the proportion of 40% of the fleet, this consumption drops to 2700 tonnes a year. The study also shows the changes in the production of wastes in relation with multi-recycling. (A.C.)

Modelling efficient innovative work: integration of economic and social psychological approaches

Directory of Open Access Journals (Sweden)

Babanova Yulia

2017-01-01

Full Text Available The article deals with the relevance of integration of economic and social psychological approaches to the solution of enhancing the efficiency of innovation management. The content, features and specifics of the modelling methods within each of approaches are unfolded and options of integration are considered. The economic approach lies in the generation of the integrated matrix concept of management of innovative development of an enterprise in line with the stages of innovative work and the use of the integrated vector method for the evaluation of the innovative enterprise development level. The social psychological approach lies in the development of a system of psychodiagnostic indexes of activity resources within the scope of psychological innovative audit of enterprise management and development of modelling methods for the balance of activity trends. Modelling the activity resources is based on the system of equations accounting for the interaction type of psychodiagnostic indexes. Integration of two approaches includes a methodological level, a level of empirical studies and modelling methods. There are suggested options of integrating the economic and psychological approaches to analyze available material and non-material resources of the enterprises’ innovative work and to forecast an optimal option of development based on the implemented modelling methods.

Barriers to development and deployment of innovative waste minimization technologies

International Nuclear Information System (INIS)

Flores, E.A.; Donaghue, J.F.

1994-08-01

Increasing regulation and scrutiny is driving waste generators towards reducing the use of scarce natural resources and reducing or eliminating was streams. There is increasing emphasis on developing and deploying technologies that meet industry needs for recovering valuable materials in a cost-effective manner. At the Department of Energy's (DOE) Hanford Site, Battelle operates Pacific Northwest Laboratory (PNL). PNL's mission is to develop technologies to clean up the environment, and to assist industry in being competitive on a global scale. One such technology developed by PNL is the Waste Acid Detoxification and Reclamation (WADR) process. This technology recovers acids from metal-bearing spent solutions, separating out the metals (which are a valuable byproduct of the acid recycling operation) from the acids. WADR uses selective precipitation and distillation together in an innovative waste recycling technology. Selective precipitation removes the heavy metals, and vacuum distillation recovers clean acid. However, WADR and other innovative waste reduction technologies face numerous barriers to successful development and deployment in the field

A model for evaluating the flow rate of an extruder for plastic recycling

International Nuclear Information System (INIS)

Oke, S.A.; Popoola, I.O.

2007-01-01

For several years, Municipal Solid Wastes (MSW) from packaging, newspapers, batteries, furniture, metals, clothing's, bottles, and food scraps have contributed negatively to the increased deterioration of our environments particularly in developing countries. It has resulted in activities that threaten lives (such as disease outbreaks and severe health hazards). As a result, governments and other stakeholders in environment have considered both theoretical and practical approaches to waste control. Recycling, which has enormous benefits of reducing manufacturing cost of new products and providing employment for the populace has been chosen as a viable option. Despite the multi-disciplinary efforts involved recycling models, guidelines applicable in the design of flow rates of extruders for plastic recycling processes are missing. This gap is addressed in the current paper. This paper conceptualizes the flow rates as an input-output system in a continuous dynamic state. With a focus on the melting activity (operation section), the analysis of flow in the metering zone involves an estimation of the quantity of recycled materials that could be produced per time. The work hopefully stimulates research in an area where quantitative methodologies are sparse. (author)

Environmental and economic assessment of a road safety product made with virgin and recycled HDPE: a comparative study.

Science.gov (United States)

L Simões, Carla; Costa Pinto, Lígia M; Bernardo, C A

2013-01-15

The development of value-added products made from post-consumer plastic recyclates has become an important goal in the quest for a sustainable society. To attain such goal, tools with higher accuracy and wider scope are increasingly necessary. The present work describes the application of a Life Cycle Assessment (LCA)/Life Cycle Costing (LCC) integrated model, with inclusion of externalities (environmental and social costs), to Anti-Glare Lamellae (AGL) made with High Density Polyethylene (HDPE). It compares an AGL currently manufactured from virgin HDPE (current AGL) with an alternative one made with recycled HDPE (optional AGL). The results obtained show that neither the current nor the optional AGL depict the best environmental performance in all impact categories. Nevertheless, there is a clear overall environmental and economic advantage in replacing virgin HDPE with recycled HDPE. The present work also makes evident that the LCA/LCC integrated model allows the identification of economic and environmental win-win and trade-off situations related to the full life cycle of products. As such, its results can be used as valuable guidelines in product development. Copyright © 2012 Elsevier Ltd. All rights reserved.

FORWARD, FUTURE AND OPTIONS ON STOCK EXCHANGE MARKET

OpenAIRE

Ljiljana Stošić Mihajlović; Ivana Zdravković

2016-01-01

The main motive of the formation and use of forward contracts and futures, and options, was certainly profit. Making financial markets more efficient, in terms of expanding the range of available financial instruments and reduction in transaction costs, these financial innovations are beneficial for both investors and managers company. Primary purpose of derivatives such as forwards, futures and options is to enable control risks by investitures and primarily from inadequate price trend...

Utilization of cement treated recycled concrete aggregates as base or subbase layer in Egypt

Directory of Open Access Journals (Sweden)

Ahmed Ebrahim Abu El-Maaty Behiry

2013-12-01

Full Text Available Recently, environmental protection has a great concern in Egypt where recycling of increased demolition debris has become a viable option to be incorporated into roads applications. An extensive laboratory program is conducted to study the feasibility of using recycled concrete aggregate (RCA mixed with traditional limestone aggregate (LSA which is currently being used in base or subbase applications in Egypt. Moreover, the influence of mixture variables on the mechanical properties of cement treated recycled aggregate (CTRA is investigated. Models to predict the compressive and tensile strengths based on mixture parameters are established. The results show that the adding of RCA improves the mechanical properties of the mixture where the unconfined compressive strength (UCS is taken as an important quality indicator. Variables influencing the UCS such as cement content, curing time, dry density play important roles to determine the performance of CTRA.

Optimisation of petroleum refinery water network systems retrofit incorporating reuse, regeneration and recycle strategies

Energy Technology Data Exchange (ETDEWEB)

Khor, Cheng Seong; Shah, Nilay [Imperial College London (United Kingdom); Mahadzir, Shuhaimi [Universiti Teknologi Petronas (Malaysia); Elkamel, Ali [University of Waterloo (Canada)

2012-02-15

Increasingly strict environmental regulations have given rise to higher requirements for operating efficiency and optimization and water has become a vital resource in the refining process and allied industries. Due to this high demand for water, plants may be exposed to supply interruptions and shortages in the future. Major concerns in the petroleum refining industry are the scarcity of fresh water supply and increasingly rigid rules on wastewater discharge, which have resulted from concerns over the environmental impact. This paper presents the efforts made to develop an optimization framework for design of petroleum refinery water network systems and retrofitting that incorporates reuse, regeneration, and recycling strategies. This framework includes the complementary advantage of water pinch analysis (WPA). Water minimization strategies were incorporated as first postulates in a superstructural representation that includes all feasible flow-sheet options for taking advantage of water reuse, regeneration and recycling opportunities. Additionally, a post-optimization analysis was carried out to evaluate the repeated treatment processes required to identify the most efficient retrofit option.

ERDA activities related to reprocessing and plutonium recycle

International Nuclear Information System (INIS)

Spurgeon, D.R.

1977-01-01

ERDA has redirected its program in support of the LWR fuel cycle from one emphasizing the commercialization of existing fuel cycle technology to a broader based assessment of alternative fuel cycle concepts with the emphasis on safeguardability and avoidance of proliferation risks. As part of this program, ERDA will evaluate a number of possible technical and institutional options to reduce proliferation risks. ERDA will continue its current program of LWR fuel reprocessing R and D with added emphasis on improved safeguards capability as well as the applicability of conventional reprocessing technology to large multinational plants. These activities and supporting design studies will provide the basis for a decision regarding the design of an optimized system for the management of spent LWR fuel. Such a system would provide a model for the development of future domestic and foreign facilities and programs. A recently completed ERDA study of the benefits of LWR reprocessing and recycle would also be expected to be factored into such a decision. The study concluded that based on currently available data, recycle of uranium and plutonium in LWR's is attractive from the standpoint of economics and resource utilization relative to the discarding of spent fuel. The LWR reprocessing/recycle picture today is clouded by several unresolved policy issues. These include the need for adequate spent fuel storage capacity for both domestic and foreign reactors; the possibility of foreign reprocessing of U.S. produced fuel; the possibility of the disposal of foreign fuel in the U.S.; the possible need to dispose of wastes generated by multinational reprocessing plants; and finally, determination of the optimum balance between recycling recovered plutonium and saving it for the breeder

Development of integrated waste management options for irradiated graphite

Energy Technology Data Exchange (ETDEWEB)

Wareing, Alan; Abrahamsen-Mills, Liam; Fowler, Linda; Jarvis, Richard; Banford, Anthony William [National Nuclear Laboratory, Warrington (United Kingdom); Grave, Michael [Doosan Babcock, Gateshead (United Kingdom); Metcalfe, Martin [National Nuclear Laboratory, Gloucestershire (United Kingdom); Norris, Simon [Radioactive Waste Management Limited, Oxon (United Kingdom)

2017-08-15

The European Treatment and Disposal of Irradiated Graphite and other Carbonaceous Waste project sought to develop best practices in the retrieval, treatment, and disposal of irradiated graphite including other irradiated carbonaceous waste such as structural material made of graphite, nongraphitized carbon bricks, and fuel coatings. Emphasis was given on legacy irradiated graphite, as this represents a significant inventory in respective national waste management programs. This paper provides an overview of the characteristics of graphite irradiated during its use, primarily as a moderator material, within nuclear reactors. It describes the potential techniques applicable to the retrieval, treatment, recycling/reuse, and disposal of these graphite wastes. Considering the lifecycle of nuclear graphite, from manufacture to final disposal, a number of waste management options have been developed. These options consider the techniques and technologies required to address each stage of the lifecycle, such as segregation, treatment, recycle, and ultimate disposal in a radioactive waste repository, providing a toolbox to aid operators and regulators to determine the most appropriate management strategy. It is noted that national waste management programs currently have, or are in the process of developing, respective approaches to irradiated graphite management. The output of the Treatment and Disposal of Irradiated Graphite and other Carbonaceous Waste project is intended to aid these considerations, rather than dictate them.

Process evaluation of enzymatic hydrolysis with filtrate recycle for the production of high concentration sugars.

Science.gov (United States)

Xue, Ying; Rusli, Jannov; Chang, Hou-Min; Phillips, Richard; Jameel, Hasan

2012-02-01

Process simulation and lab trials were carried out to demonstrate and confirm the efficiency of the concept that recycling hydrolysate at low total solid enzymatic hydrolysis is one of the options to increase the sugar concentration without mixing problems. Higher sugar concentration can reduce the capital cost for fermentation and distillation because of smaller retention volume. Meanwhile, operation cost will also decrease for less operating volume and less energy required for distillation. With the computer simulation, time and efforts can be saved to achieve the steady state of recycling process, which is the scenario for industrial production. This paper, to the best of our knowledge, is the first paper discussing steady-state saccharification with recycling of the filtrate form enzymatic hydrolysis to increase sugar concentration. Recycled enzymes in the filtrate (15-30% of the original enzyme loading) resulted in 5-10% higher carbohydrate conversion compared to the case in which recycled enzymes were denatured. The recycled hydrolysate yielded 10% higher carbohydrate conversion compared to pure sugar simulated hydrolysate at the same enzyme loading, which indicated hydrolysis by-products could boost enzymatic hydrolysis. The high sugar concentration (pure sugar simulated) showed inhibition effect, since about 15% decrease in carbohydrate conversion was observed compared with the case with no sugar added. The overall effect of hydrolysate recycling at WinGEMS simulated steady-state conditions with 5% total solids was increasing the sugar concentration from 35 to 141 g/l, while the carbohydrate conversion was 2% higher for recycling at steady state (87%) compared with no recycling strategy (85%). Ten percent and 15% total solid processes were also evaluated in this study.

Innovative development and factors affecting the innovative activity of industrial enterprises in Bulgaria

Directory of Open Access Journals (Sweden)

Sotirova Asya Olegova

2016-12-01

Full Text Available Innovations are a necessity, innovations are a factor, innovations are the moving force of the companies in the 21st century. Every modern manager should recognize the role of innovations for the existence of the enterprises and to aim at innovative development. The novelties in various areas are to be followed up. It is necessary to look for the options and to overcome the obstacles standing in the way of innovations. The major objective of this article is to establish the state of innovative activity of industrial enterprises in Bulgaria and to identify the factors exercising the largest influence on their innovative development. The major results to be achieved are the establishment of the basic internal and external factors that support innovations, the deduction of the major problems occurring during the innovation process and the establishment of some directives to activation. The major methods of study used in this work are statistical methods for evaluation, method of analysis and synthesis, method of comparison. Information of literature sources has been studied and systematized within the process of research, as well as analytical reports of Bulgaria and the European Union, and results from an inquiry held are used, as well as statistical data of the National Statistical Institute of the Republic of Bulgaria.

Open innovation models - a case study of playing poker with chess pieces

DEFF Research Database (Denmark)

Goduscheit, René Chester; Bergenholtz, Carsten; Jørgensen, Jacob Høj

2009-01-01

The qualities of employing open innovation models are widely acknowledgedamong academics and practitioners. Open innovation is perceived as a meansto ensure flexibility and create options for future business. However, theorganisational challenges in employing open innovation models as opposed tom...

Rethink, Rework, Recycle.

Science.gov (United States)

Wrhen, Linda; DiSpezio, Michael A.

1991-01-01

Information about the recycling and reuse of plastics, aluminum, steel, glass, and newspapers is presented. The phases of recycling are described. An activity that allows students to separate recyclable materials is included. The objectives, a list of needed materials, and procedure are provided. (KR)

Recycling at Penn State's Beaver Stadium. "Recycle on the Go" Success Story

Science.gov (United States)

US Environmental Protection Agency, 2009

2009-01-01

With a 13-year-old recycling program, The Pennsylvania State University's (Penn State) Beaver Stadium in the past diverted nearly 30 tons of recyclables per year from local landfills. A new initiative to promote recycling in the stadium's tailgating area has helped Penn State more than triple its old recycling record, collecting 112 tons in 2008.…

Recycling of electronic scrap

DEFF Research Database (Denmark)

Legarth, Jens Brøbech

This Ph.D. thesis deals with the growingly important field of electronics recycling with special attention to the problem of printed circuit board recycling. A literature survey of contemporary electronics recycling and printed circuit board recycling is presented.Further, an analysis of the role...

A real-life example of choosing an inherently safer process option

International Nuclear Information System (INIS)

Study, Karen

2007-01-01

While choosing an inherently safer alternative may seem straightforward, sometimes what seems to be the most obvious alternative may not provide the best risk reduction. The process designer must maintain a broad perspective to be able to recognize all potential hazards when evaluating design options. All aspects of operation such as start-up, shut-down, utility failure, as well as normal operation should be considered. Choosing the inherently safer option is best accomplished early in the option selection phase of a project; however, recycle back to the option selection phase may be needed if an option is not thoroughly evaluated early in the process. In this paper, a project to supply ammonia to a catalytic reactor will be reviewed. During the course of the project, an 'inherently safer' alternative was selected and later discarded due to issues uncovered during the detail design phase. The final option chosen will be compared to (1) the original design and (2) the initial 'inherently safer' alternative. The final option was inherently safer than both the original design and the initial 'inherently safer' alternative even though the design team initially believed that it would not be

Assessment of recycling or disposal alternatives for radioactive scrap metal

International Nuclear Information System (INIS)

Murphie, W.E.; Lilly, M.J. III; Nieves, L.A.; Chen, S.Y.

1993-01-01

The US Department of Energy, Office of Environmental Restoration and Waste Management, Oak Ridge Programs Division, is participating with the Organization for Economic Cooperation and Development in providing analytical support for evaluation of management alternatives for radioactive scrap metals. For this purpose, Argonne National Laboratory is assessing environmental and societal implications of recycling and/or disposal process alternatives. This effort includes development of inventory estimates for contaminated metals; investigation of scrap metal market structure, processes, and trends; assessment of radiological and nonradiological effects of recycling; and investigation of social and political factors that are likely to either facilitate or constrain recycling opportunities. In addition, the option of scrap metal disposal is being assessed, especially with regard to the environmental and health impacts of replacing these metals if they are withdrawn from use. This paper focuses on the radiological risk assessment and dose estimate sensitivity analysis. A open-quotes tieredclose quotes concept for release categories, with and without use restrictions, is being developed. Within the tiers, different release limits may be indicated for specific groupings of radionuclides. Depending on the spectrum of radionuclides that are present and the level of residual activity after decontamination and/or smelting, the scrap may be released for unrestricted public use or for specified public uses, or it may be recycled within the nuclear industry. The conservatism of baseline dose estimates is examined, and both more realistic parameter values and protective measures for workers are suggested

Recycle and reuse of materials and components from waste streams of nuclear fuel cycle facilities

International Nuclear Information System (INIS)

2000-01-01

All nuclear fuel cycle processes utilize a wide range of equipment and materials to produce the final products they are designed for. However, as at any other industrial facility, during operation of the nuclear fuel cycle facilities, apart from the main products some byproducts, spent materials and waste are generated. A lot of these materials, byproducts or some components of waste have a potential value and may be recycled within the original process or reused outside either directly or after appropriate treatment. The issue of recycle and reuse of valuable material is important for all industries including the nuclear fuel cycle. The level of different materials involvement and opportunities for their recycle and reuse in nuclear industry are different at different stages of nuclear fuel cycle activity, generally increasing from the front end to the back end processes and decommissioning. Minimization of waste arisings and the practice of recycle and reuse can improve process economics and can minimize the potential environmental impact. Recognizing the importance of this subject, the International Atomic Energy Agency initiated the preparation of this report aiming to review and summarize the information on the existing recycling and reuse practice for both radioactive and non-radioactive components of waste streams at nuclear fuel cycle facilities. This report analyses the existing options, approaches and developments in recycle and reuse in nuclear industry

Background study on increasing recycling of end-of-life mercury-containing lamps from residential and commercial sources in Canada

Energy Technology Data Exchange (ETDEWEB)

Hilkene, C. [Hilkene International Policy, Toronto, ON (Canada); Friesen, K. [Pollution Probe, Toronto, ON (Canada)

2005-10-31

The state of recycling of mercury-containing lamps in Canada was studied. Developing an efficient recovery and recycling infrastructure for mercury-containing lamps offers several benefits such as environmental protection from releases of mercury; displacing virgin materials required for production of new lamps; and increasing the sustainability associated with the use of these energy efficient products. This study summarized international experience with respect to recovery and recycling of mercury-containing lamps. It also summarized the material composition of these lamps, and provided an inventory of Canadian fluorescent lamp recycling and recovery initiatives. It provided estimates of quantities of end-of-life bulbs and tubes being disposed of in Canada; quantities of metals and other materials recovered through lamp recycling; the tonnage of metals and other materials being lost to disposal systems and energy savings and associated greenhouse gas emission reductions from substitution of recycled fluorescent lamp materials for virgin materials in manufacturing operations. The report also identified other environmental benefits arising from current or potential recycling and recovery initiatives as well as recovery opportunities and barriers to fluorescent lamp recovery and recycling initiatives. Last, the report presented options for stimulating greater recovery and recycling of mercury-containing lamps and presented critical factors for a meaningful cost benefit analysis on enhanced recovery. 76 refs., 16 tabs., 2 figs., 6 appendices.

A proposal for an international program to develop dry recycle of spent nuclear fuel

International Nuclear Information System (INIS)

Feinroth, H.

1999-01-01

The dry oxidation-reduction process (called OREOX for Oxidation Reduction of Oxide Fuel) being developed by Korea and Canada, in cooperation with IAEA and the US State Department, is limited to recycle of spent LWR fuel into CANDU reactors (DUPIC). When first conceived and demonstrated via irradiation of test elements by Atomics International in 1965, (the process was called AIROX at that time) a wider range of applications was intended, including recycle of spent LWR fuel into LWRs. Studies sponsored by DOE's Idaho Office in 1992 confirmed the applicability of this technology to regions containing LWR's only, and described the potential advantages of such recycle from an environmental, waste management and economic point of view, as compared to the direct disposal option. Recent analyses conducted by the author indicates that such dry recycle may be one of the few acceptable paths remaining for resolution of the US spent fuel storage dilemma that remains consistent with US non-proliferation policy. It is proposed that a new US program be established to develop AIROX dry recycle for use in the US, and this become part of an international cooperative program, including the current Canadian - Korean program, and possibly including participation of other countries wishing to pursue alternatives to the once through cycle, and wet reprocessing. With shared funding of major project elements, such international cooperation would accelerate the demonstration and commercial deployment of dry recycle technology, as compared to separate and independent programs in each country. (author)

Education Innovation in Veterinary Training: E-learning Options in ...

African Journals Online (AJOL)

Changing needs in education call for innovative ideas in veterinary education. The University of Pretoria has adopted a policy of flexible learning that makes provision for flexible learning opportunities as well as flexible delivery systems. The preferred mode(s) of instruction to be used by a lecturer will be determined by the ...

Modelling Recycling Targets

DEFF Research Database (Denmark)

hill, amanda; Leinikka Dall, Ole; Andersen, Frits Møller

2014-01-01

% for household waste, and sets an ambitious goal of a 50% recycling rate by 2020. This study integrates the recycling target into the FRIDA model to project how much waste and from which streams should be diverted from incineration to recycling in order to achieve the target. Furthermore, it discusses how...

DESIGN CONSIDERATIONS UPON PRODUCT END-OF-LIFE OPTIONS

Directory of Open Access Journals (Sweden)

BARSAN Lucian

2016-11-01

Full Text Available The paper presents some considerations about the necessity of evaluating the environmental impact of a product during its entire life. The present situation (economic, social and ecologic imposes solutions to reduce this impact as a result of an analysis performed during all stages of the life cycle. This paper focuses on design solutions with consequences in the last stage, the end-of-life. Reusing products, with, or without remanufacturing and recycling the materials from products that cannot be reused represent some options analysed in this paper. The end-of-life options should be known even from the beginning of the design process and should be included as design objectives or, at least as constrictions. Considering them as human needs would naturally include them in the requirements list.

Recycling production designs: the value of coordination and flexibility in aluminum recycling operations

Science.gov (United States)

Brommer, Tracey H.

The growing motivation for aluminum recycling has prompted interest in recycling alternative and more challenging secondary materials. The nature of these alternative secondary materials necessitates the development of an intermediate recycling facility that can reprocess the secondary materials into a liquid product Two downstream aluminum remelters will incorporate the liquid products into their aluminum alloy production schedules. Energy and environmental benefits result from delivering the products as liquid but coordination challenges persist because of the energy cost to maintain the liquid. Further coordination challenges result from the necessity to establish a long term recycling production plan in the presence of long term downstream aluminum remelter production uncertainty and inherent variation in the daily order schedule of the downstream aluminum remelters. In this context a fundamental question arises, considering the metallurgical complexities of dross reprocessing, what is the value of operating a coordinated set of by-product reprocessing plants and remelting cast houses? A methodology is presented to calculate the optimal recycling center production parameters including 1) the number of recycled products, 2) the volume of recycled products, 3) allocation of recycled materials across recycled products, 4) allocation of recycled products across finished alloys, 4) the level of flexibility for the recycling center to operate. The methods implemented include, 1) an optimization model to describe the long term operations of the recycling center, 2) an uncertainty simulation tool, 3) a simulation optimization method, 4) a dynamic simulation tool with four embedded daily production optimization models of varying degrees of flexibility. This methodology is used to quantify the performance of several recycling center production designs of varying levels of coordination and flexibility. This analysis allowed the identification of the optimal recycling

Concrete produced with recycled aggregates

Directory of Open Access Journals (Sweden)

J. J. L. Tenório

Full Text Available This paper presents the analysis of the mechanical and durable properties of recycled aggregate concrete (RAC for using in concrete. The porosity of recycled coarse aggregates is known to influence the fresh and hardened concrete properties and these properties are related to the specific mass of the recycled coarse aggregates, which directly influences the mechanical properties of the concrete. The recycled aggregates were obtained from construction and demolition wastes (CDW, which were divided into recycled sand (fine and coarse aggregates. Besides this, a recycled coarse aggregate of a specific mass with a greater density was obtained by mixing the recycled aggregates of the CDW with the recycled aggregates of concrete wastes (CW. The concrete was produced in laboratory by combining three water-cement ratios, the ratios were used in agreement with NBR 6118 for structural concretes, with each recycled coarse aggregates and recycled sand or river sand, and the reference concrete was produced with natural aggregates. It was observed that recycled aggregates can be used in concrete with properties for structural concrete. In general, the use of recycled coarse aggregate in combination with recycled sand did not provide good results; but when the less porous was used, or the recycled coarse aggregate of a specific mass with a greater density, the properties of the concrete showed better results. Some RAC reached bigger strengths than the reference concrete.

IAEA Technical Meeting on Innovative Heat Exchanger and Steam Generator Designs for Fast Reactors. Presentations

International Nuclear Information System (INIS)

2011-01-01

The fast reactor, which can generate electricity and breed additional fissile material for future fuel stocks, is a resource that will be needed when economic uranium supplies for the thermal reactors diminish. Further, the fast-fission fuel cycle in which material is recycled (a basic requirement to meet sustainability criteria) offers the flexibility needed to contribute decisively towards solving the problem of growing “spent” fuel inventories by greatly reducing the volume, the heat load and the radiotoxic inventory of high-level wastes that must be disposed of in long-term geological repositories. This is a waste management option that will play an increasingly important role in the future, and help to ensure that nuclear energy remains a sustainable long-term option in the world’s overall energy mix. In recognition of the fast reactor’s importance for the sustainability of the nuclear option, currently there is worldwide renewed interest in fast reactor technology development, as indicated, e.g., by the outcome of the Generation IV International Forum (GIF) technology review, which concluded with 3 out of 6 innovative systems to be fast reactors (gas cooled fast reactor, sodium cooled fast reactor, and heavy liquid metal cooled fast reactor), plus a potential fast core for a 4th concept, the super-critical water reactor. Currently, fast reactor construction projects are ongoing in India (PFBR) and Russian Federation (BN-800), whilst in China the first experimental fast reactor (CEFR) is in the commissioning phase. Fast reactor programs are also carried out in Europe (in particular in France), Japan, Republic of Korea and the USA. The most important challenges for fast reactors are in the areas of cost competitiveness with respect to LWRs and other energy sources, enhanced safety, non-proliferation, and public acceptance. With the exception of this latter, these translate into technology development challenges, i.e. the development of advanced reactor

Green Science: Revisiting Recycling

Science.gov (United States)

Palliser, Janna

2011-01-01

Recycling has been around for a long time--people have reused materials and refashioned them into needed items for thousands of years. More recently, war efforts encouraged conservation and reuse of materials, and in the 1970s recycling got its official start when recycling centers were created. Now, curbside recycling programs and recycling…

Evaluation of disposal, recycling and clearance scenarios for managing ARIES radwaste after plant decommissioning

International Nuclear Information System (INIS)

El-Guebaly, L.

2007-01-01

The wealth of experience accumulated over the past 30-40 years of fusion power plant studies must be forged into a new strategy to reshape all aspects of handling the continual stream of radioactive materials during operation and after power plant decommissioning. With tighter environmental controls and the political difficulty of building new repositories worldwide, the disposal option could be replaced with more environmentally attractive scenarios, such as recycling and clearance. We applied the three scenarios to the most recent ARIES compact stellarator power plant. All ARIES-CS components qualify as Class A or C low-level waste, according to the US guidelines, and can potentially be recycled using conventional and advanced remote handling equipment. Approximately 80% of the total waste can be cleared for reuse within the nuclear industry or, preferably, released to the commercial market. This paper documents the recent developments in radwaste management of nuclear facilities and highlights the benefits and challenges of disposal, recycling and clearance

Assessment of the impact of innovation processes: methodological approaches

Directory of Open Access Journals (Sweden)

Demilkhanova B.A.

2016-12-01

Full Text Available in the article the prospects of development of innovative processes at a regional level the system of indicators of assessment effective components of innovation potential of the region. A conclusion about the predominance in the economy of the regions under study investment options for updating technology has been made based on the calculation and analysis of indicators of innovation investment in the fixed capital.

Innovation and energy. ECRIN day; Innovation et energie. Journee ECRIN

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

ECRIN is an association jointly created by the French atomic energy commission (CEA) and the French national center of scientific research (CNRS). It gathers experts from the research and industry worlds, representatives of institutions and decision making peoples in order to work on important topics like energy. This document gathers the working documents and transparencies presented at the ECRIN day on energy and innovation: opening talk of C. Birraux (head of the parliamentary office of evaluation of scientific and technological choices); the energy of seas (offshore wind power, wave energy, tide currents energy, thermal energy of seas, osmotic energy, tidal energy); synthetic fuels (stakes, possible options, Fischer-Tropsch synthesis, GTL, CTL, BTL, production with CO{sub 2} recycling); capture and geological sequestration of CO{sub 2}: a general overview (stakes, solutions, capture and sequestration, transport, geologic disposal, present day situation and perspectives); geothermal energy: new prospects (enhanced geothermal systems, hot-dry-rocks and hot fractured rocks, advances, cost, advantages and drawbacks); heat pumps and valorization of low temperature heat sources (space heating, district heating networks, heat pumps, artificial geothermal energy, low temperature water transport, thermal potentiality); heat and coldness storage and transport (use of intermittent energy sources, cogeneration, optimisation of processes, recovery of heat losses, CO{sub 2} capture, present-day situation, problems to be solved, integration of systems and processes); plastic photovoltaic solar cells (market, stakes, potentialities of organic materials for photovoltaic conversion, state-of-the-art, research in Europe and France, perspectives); conclusion of the Ecrin day (challenges, diversification of energy sources, energy efficiency, abatement of CO{sub 2} emissions, role of ECRIN). (J.S.)

Decontamination of process equipment using recyclable chelating solvent

International Nuclear Information System (INIS)

Jevec, J.; Lenore, C.; Ulbricht, S.

1995-01-01

The Department of Energy (DOE) is now faced with the task of meeting decontamination and decommissioning obligations at numerous facilities by the year 2019. Due to the tremendous volume of material involved, innovative decontamination technologies are being sought that can reduce the volumes of contaminated waste materials and secondary wastes requiring disposal. With sufficient decontamination, some of the material from DOE facilities could be released as scrap into the commercial sector for recycle, thereby reducing the volume of radioactive waste requiring disposal. Although recycling may initially prove to be more costly than current disposal practices, rapidly increasing disposal costs are expected to make recycling more and more cost effective. Additionally, recycling is now perceived as the ethical choice in a world where the consequences of replacing resources and throwing away reusable materials are impacting the well-being of the environment. Current approaches to the decontamination of metals most often involve one of four basic process types: (1) chemical, (2) manual and mechanical, (3) electrochemical, and (4) ultrasonic. open-quotes Hardclose quotes chemical decontamination solutions, capable of achieving decontamination factors (Df's) of 50 to 100, generally involve reagent concentrations in excess of 5%, tend to physically degrade the surface treated, and generate relatively large volumes of secondary waste. open-quotes Softclose quotes chemical decontamination solutions, capable of achieving Df's of 5 to 10, normally consist of reagents at concentrations of 0.1 to 1%, generally leave treated surfaces in a usable condition, and generate relatively low secondary waste volumes. Under contract to the Department of Energy, the Babcock ampersand Wilcox Company is developing a chemical decontamination process using chelating agents to remove uranium compounds and other actinide species from process equipment

Options Study - Phase II

Energy Technology Data Exchange (ETDEWEB)

R. Wigeland; T. Taiwo; M. Todosow; W. Halsey; J. Gehin

2010-09-01

The Options Study has been conducted for the purpose of evaluating the potential of alternative integrated nuclear fuel cycle options to favorably address the issues associated with a continuing or expanding use of nuclear power in the United States. The study produced information that can be used to inform decisions identifying potential directions for research and development on such fuel cycle options. An integrated nuclear fuel cycle option is defined in this study as including all aspects of the entire nuclear fuel cycle, from obtaining natural resources for fuel to the ultimate disposal of used nuclear fuel (UNF) or radioactive wastes. Issues such as nuclear waste management, especially the increasing inventory of used nuclear fuel, the current uncertainty about used fuel disposal, and the risk of nuclear weapons proliferation have contributed to the reluctance to expand the use of nuclear power, even though it is recognized that nuclear power is a safe and reliable method of producing electricity. In this Options Study, current, evolutionary, and revolutionary nuclear energy options were all considered, including the use of uranium and thorium, and both once-through and recycle approaches. Available information has been collected and reviewed in order to evaluate the ability of an option to clearly address the challenges associated with the current implementation and potential expansion of commercial nuclear power in the United States. This Options Study is a comprehensive consideration and review of fuel cycle and technology options, including those for disposal, and is not constrained by any limitations that may be imposed by economics, technical maturity, past policy, or speculated future conditions. This Phase II report is intended to be used in conjunction with the Phase I report, and much information in that report is not repeated here, although some information has been updated to reflect recent developments. The focus in this Options Study was to

Proposal of a torus pumping and fuel recycling system for ITER

International Nuclear Information System (INIS)

Perinic, D.; Mack, A.; Perinic, G.; Murdoch, D.

1995-01-01

A universal torus pumping and fuel recycling system is proposed for all operation modes of ITER. It comprises primary cryopumps and secondary fuel separating cryopumps located inside the cryostat and a common mechanical forepump station located outside the cryostat. In this paper two different primary cryopump options are compared. The results of Monte Carlo calculations of pumping probabilities for helium show a significant difference leading to a distinct preference for the concept of a co-pumping cryopump. (orig.)

Nuclear fuel cycle waste recycling technology deverlopment - Radioactive metal waste recycling technology development

International Nuclear Information System (INIS)

Oh, Won Zin; Moon, Jei Kwon; Jung, Chong Hun; Park, Sang Yoon

1998-08-01

With relation to recycling of the radioactive metal wastes which are generated during operation and decommissioning of nuclear facilities, the following were described in this report. 1. Analysis of the state of the art on the radioactive metal waste recycling technologies. 2. Economical assessment on the radioactive metal waste recycling. 3. Process development for radioactive metal waste recycling, A. Decontamination technologies for radioactive metal waste recycling. B. Decontamination waste treatment technologies, C. Residual radioactivity evaluation technologies. (author). 238 refs., 60 tabs., 79 figs

The fast-recycling receptor Megalin defines the apical recycling pathway of epithelial cells

Science.gov (United States)

Perez Bay, Andres E.; Schreiner, Ryan; Benedicto, Ignacio; Paz Marzolo, Maria; Banfelder, Jason; Weinstein, Alan M.; Rodriguez-Boulan, Enrique J.

2016-01-01

The basolateral recycling and transcytotic pathways of epithelial cells were previously defined using markers such as transferrin (TfR) and polymeric IgA (pIgR) receptors. In contrast, our knowledge of the apical recycling pathway remains fragmentary. Here we utilize quantitative live-imaging and mathematical modelling to outline the recycling pathway of Megalin (LRP-2), an apical receptor with key developmental and renal functions, in MDCK cells. We show that, like TfR, Megalin is a long-lived and fast-recycling receptor. Megalin enters polarized MDCK cells through segregated apical sorting endosomes and subsequently intersects the TfR and pIgR pathways at a perinuclear Rab11-negative compartment termed common recycling endosomes (CRE). Whereas TfR recycles to the basolateral membrane from CRE, Megalin, like pIgR, traffics to subapical Rab11-positive apical recycling endosomes (ARE) and reaches the apical membrane in a microtubule- and Rab11-dependent manner. Hence, Megalin defines the apical recycling pathway of epithelia, with CRE as its apical sorting station. PMID:27180806

End-of-Life in the railway sector: Analysis of recyclability and recoverability for different vehicle case studies.

Science.gov (United States)

Delogu, Massimo; Del Pero, Francesco; Berzi, Lorenzo; Pierini, Marco; Bonaffini, Davide

2017-02-01

The railway system represents one of the most resource-efficient answer to our ever-growing demand for transport service and the development trends for the following years forecast a substantial increase in this sector. Considering the European Union, rolling stock realizes a significant share of both goods and passengers carriage while it is responsible for a derisory quota of environmental impact and energy consumption involved by transportation. Contrary to the low environmental impact, the amount of End-of-Life (EoL) waste generated by rolling stocks in relation to the number of vehicles is notable, much greater than in the case of road vehicles. As railway vehicles are constituted by many heterogeneous components, the EoL rolling stock is a precious source of materials, whose recycling brings measurable economic benefits and needs to be appropriately debated. The paper presents calculation of recoverability/recyclability rate for different typologies of vehicles representative of railway transport; calculation is performed on the basis of primary data and according to the recyclability and recoverability calculation method issued by UNIFE in the context of Product Category Rules (PCR). The typologies of railway vehicles taken into account are electric metro, diesel commuter train and high-speed electric train. The analysis envisages also to replicate the calculation in case innovative materials and manufacturing technologies are adopted in the construction of car-body structure. Results show that recyclability/recoverability rates are abundantly over the quota of 90% for each one of the three trains, these latter being made in major part of metals that benefit from very efficient recovery processes. The adoption of innovative materials and manufacturing technologies for car-body structure involves a scarce reduction of recyclability and recoverability rates (about 2% and 0.2% respectively) due to the introduction of components and materials characterized by

Central sorting and recovery of MSW recyclable materials: A review of technological state-of-the-art, cases, practice and implications for materials recycling.

Science.gov (United States)

Cimpan, Ciprian; Maul, Anja; Jansen, Michael; Pretz, Thomas; Wenzel, Henrik

2015-06-01

Today's waste regulation in the EU comprises stringent material recovery targets and calls for comprehensive programs in order to achieve them. A similar movement is seen in the US where more and more states and communities commit to high diversion rates from landfills. The present paper reviews scientific literature, case studies and results from pilot projects, on the topic of central sorting of recyclable materials commonly found in waste from households. The study contributes, inter alia, with background understanding on the development of materials recovery, both in a historical and geographical perspective. Physical processing and sorting technology has reached a high level of maturity, and many quality issues linked to cross-contamination by commingling have been successfully addressed to date. New sorting plants tend to benefit from economies of scale, and innovations in automation and process control, which are targeted at curtailing process inefficiencies shown by operational practice. Technology developed for the sorting of commingled recyclables from separate collection is also being successfully used to upgrade residual MSW processing plants. The strongest motivation for central sorting of residual MSW is found for areas where source separation and separate collection is difficult, such as urban agglomerations, and can in such areas contribute to increasing recycling rates, either complementary to- or as a substitute for source separation of certain materials, such as plastics and metals. Copyright © 2015 Elsevier Ltd. All rights reserved.

Minimization of actinide waste by multi-recycling of thoriated fuels in the EPR reactor

Directory of Open Access Journals (Sweden)

Nuttin A.

2012-02-01

Full Text Available The multi-recycling of innovative uranium/thorium oxide fuels for use in the European Pressurized water Reactor (EPR has been investigated. If increasing quantities of 238U, the fertile isotope in standard UO2 fuel, are replaced by 232Th, then a greater yield of new fissile material (233U is produced during the cycle than would otherwise be the case. This leads to economies of natural uranium of around 45% if the uranium in the spent fuel is multi-recycled. In addition we show that minor actinide and plutonium waste inventories are reduced and hence waste radio-toxicities and decay heats are up to a factor of 20 lower after 103 years. Two innovative fuel types named S90 and S20, ThO2 mixed with 90% and 20% enriched UO2 respectively, are compared as an alternative to standard uranium oxide (UOX and uranium/plutonium mixed oxide (MOX fuels at the longest EPR fuel discharge burn-ups of 65 GWd/t. Fissile and waste inventories are examined, waste radio-toxicities and decay heats are extracted and safety feedback coefficients are calculated.

Usage of Recycled Pet

Directory of Open Access Journals (Sweden)

A. Ebru Tayyar

2010-01-01

Full Text Available The increasing industrialization, urbanization and the technological development have caused to increase depletion of the natural resources and environmental pollution's problem. Especially, for the countries which have not enough space recycling of the waste eliminating waste on regular basis or decreasing the amount and volume of waste have provided the important advantages. There are lots of studies and projects to develop both protect resources and prevent environmental pollution. PET bottles are commonly used in beverage industry and can be reused after physical and chemical recycling processes. Usage areas of recycled PET have been developed rapidly. Although recycled PET is used in plastic industry, composite industry also provides usage alternatives of recycled PET. Textile is a suitable sector for recycling of some plastics made of polymers too. In this study, the recycling technologies and applications of waste PET bottles have been investigated and scientific works in this area have been summarized.

National Options for a Sustainable Nuclear Energy System: MCDM Evaluation Using an Improved Integrated Weighting Approach

Directory of Open Access Journals (Sweden)

Ruxing Gao

2017-12-01

Full Text Available While the prospects look bright for nuclear energy development in China, no consensus about an optimum transitional path towards sustainability of the nuclear fuel cycle has been achieved. Herein, we present a preliminary study of decision making for China’s future nuclear energy systems, combined with a dynamic analysis model. In terms of sustainability assessment based on environmental, economic, and social considerations, we compared and ranked the four candidate options of nuclear fuel cycles combined with an integrated evaluation analysis using the Multi-Criteria Decision Making (MCDM method. An improved integrated weighting method was first applied in the nuclear fuel cycle evaluation study. This method synthesizes diverse subjective/objective weighting methods to evaluate conflicting criteria among the competing decision makers at different levels of expertise and experience. The results suggest that the fuel cycle option of direct recycling of spent fuel through fast reactors is the most competitive candidate, while the fuel cycle option of direct disposal of all spent fuel without recycling is the least attractive for China, from a sustainability perspective. In summary, this study provided a well-informed decision-making tool to support the development of national nuclear energy strategies.

Development of integrated waste management options for irradiated graphite

Directory of Open Access Journals (Sweden)

Alan Wareing

2017-08-01

Full Text Available The European Treatment and Disposal of Irradiated Graphite and other Carbonaceous Waste project sought to develop best practices in the retrieval, treatment, and disposal of irradiated graphite including other irradiated carbonaceous waste such as structural material made of graphite, nongraphitized carbon bricks, and fuel coatings. Emphasis was given on legacy irradiated graphite, as this represents a significant inventory in respective national waste management programs. This paper provides an overview of the characteristics of graphite irradiated during its use, primarily as a moderator material, within nuclear reactors. It describes the potential techniques applicable to the retrieval, treatment, recycling/reuse, and disposal of these graphite wastes. Considering the lifecycle of nuclear graphite, from manufacture to final disposal, a number of waste management options have been developed. These options consider the techniques and technologies required to address each stage of the lifecycle, such as segregation, treatment, recycle, and ultimate disposal in a radioactive waste repository, providing a toolbox to aid operators and regulators to determine the most appropriate management strategy. It is noted that national waste management programs currently have, or are in the process of developing, respective approaches to irradiated graphite management. The output of the Treatment and Disposal of Irradiated Graphite and other Carbonaceous Waste project is intended to aid these considerations, rather than dictate them.

Assessing changes on poly(ethylene terephthalate) properties after recycling: Mechanical recycling in laboratory versus postconsumer recycled material

Energy Technology Data Exchange (ETDEWEB)

López, María del Mar Castro, E-mail: quimcl02@udc.es [Grupo de Polímeros, Centro de Investigacións Tecnológicas (CIT), Departamento de Física, Escuela Universitaria Politécnica, Universidade de A Coruña, Campus de Ferrol, 15403 Ferrol (Spain); Ares Pernas, Ana Isabel, E-mail: aares@udc.es [Grupo de Polímeros, Centro de Investigacións Tecnológicas (CIT), Departamento de Física, Escuela Universitaria Politécnica, Universidade de A Coruña, Campus de Ferrol, 15403 Ferrol (Spain); Abad López, Ma José, E-mail: mjabad@udc.es [Grupo de Polímeros, Centro de Investigacións Tecnológicas (CIT), Departamento de Física, Escuela Universitaria Politécnica, Universidade de A Coruña, Campus de Ferrol, 15403 Ferrol (Spain); and others

2014-10-15

Keeping rheological, mechanical and thermal properties of virgin poly(ethylene terephthalate), PET, is necessary to assure the quality of second-market applications. A comparative study of these properties has been undertaken in virgin, mechanical recycled and commercial recycled PET samples. Viscoelastic characterization was carried out by rheological measurements. Mechanical properties were estimated by tensile and Charpy impact strength tests. Thermal properties and crystallinity were evaluated by differential scanning calorimetry and a deconvolution procedure was applied to study the population of the different crystals. Molecular conformational changes related to crystallinity values were studied by FTIR spectroscopy. Variations in average molecular weight were predicted from rheology. Besides, the presence-absence of linear and cyclic oligomeric species was measured by mass spectrometry techniques, as MALDI-TOF. Mechanical recycled PET undergoes a significant decline in rheological, mechanical and thermal properties upon increasing the number of reprocessing steps. This is due to the cleavage of the ester bonds with reduction in molar mass and raise in cyclic oligomeric species, in particular [GT{sub c}]{sub n} and [GT{sub c}]{sub n}-G type. Chain shortening plus enrichment in trans conformers favour the crystallization process which occurs earlier and faster with modification in crystal populations. Additional physicochemical steps are necessary to preserve the main benefits of PET. - Highlights: • Combination of multiple techniques to characterize the effects of recycling in PET. • Cleavage of ester bonds reduced viscosity, Mw, toughness in mechanical recycled PET. • Virgin, mechanical recycled and commercial recycled PET differ in crystal populations. • Cyclic oligomers [GT{sub c}]{sub n} and [GT{sub c}]{sub n}-G increase from the fourth extrusion cycle onwards.

Dual recycling for GEO 600

International Nuclear Information System (INIS)

Grote, H; Freise, A; Malec, M; Heinzel, G; Willke, B; Lueck, H; Strain, K A; Hough, J; Danzmann, K

2004-01-01

Dual recycling is the combination of signal recycling and power recycling; both optical techniques improve the shot-noise-limited sensitivity of interferometric gravitational-wave detectors. In addition, signal recycling can reduce the loss of light power due to imperfect interference and allows us, in principle, to beat the standard quantum limit. The interferometric gravitational-wave detector GEO 600 is the first of the kilometre-scale detectors to use signal recycling. We have recently equipped the detector with a signal-recycling mirror with a transmittance of 1%. In this paper, we present details of the detector commissioning and the first locks of the dual-recycled interferometer

Charter Schools: A Viable Public School Choice Option?

Science.gov (United States)

Geske, Terry G.; And Others

1997-01-01

Overviews the charter-school phenomenon and these schools' basic design. Discusses the government's role in education and identifies various school-choice options. Explores overall autonomy via legislative provisions and examines empirical evidence on charter schools' innovative features, teacher and student characteristics, and parental contracts…

Recycling Mentors: an intergenerational, service-learning program to promote recycling and environmental awareness.

Science.gov (United States)

D'abundo, Michelle L; Fugate-Whitlock, Elizabeth I; Fiala, Kelly A

2011-01-01

The purpose of Recycling Mentors was to implement an intergenerational, service-learning program focused on promoting recycling and environmental awareness among students enrolled in Community Health (HEA 301) and Current Issues in Gerontology (GRN 440/540) and adults older than 60 years. Recycling Mentors was conducted in New Hanover County (NHC), North Carolina, where a moderate climate and coastal location attracts many tourists, retirees, and college students. A community like NHC is a good place to implement service-learning that educates both students and older adults about the benefits of recycling to individual health and the environment. During the Fall 2009 semester, undergraduate and graduate students completed institutional review board training and then conducted the program with older adults. The education component of Recycling Mentors included a pre/post survey, brochure, and scheduled visits. Overall, Recycling Mentors was positive service-learning experience with students identifying salient outcomes such as learning about recycling and the environment and working with older adults. In addition, teaching the education component of Recycling Mentors was good practice for students who will be the future health professionals. While service-learning and environmentally themed projects are common, a program that combines the 2 like Recycling Mentors is unique and has the potential to motivate individual change while positively impacting the local community and the environment.

Towards an Intellectual Property Rights Strategy for Innovation in Europe

NARCIS (Netherlands)

Radauer, Alfred; Rodriguez, V.F.

2009-01-01

On October 13, 2009 the Science and Technology Options Assessment Panel (STOA) together with Knowledge4Innovation/The Lisbon Forum, supported by Technopolis Consulting Group and TNO, organised a half-day workshop entitled ‘Towards an Intellectual Property Rights Strategy for Innovation in Europe’.

Physics of plutonium recycling

International Nuclear Information System (INIS)

2003-01-01

The commercial recycling of plutonium as PuO 2 /UO 2 mixed-oxide (MOX) fuel is an established practice in pressurised water reactors (PWRs) in several countries, the main motivation being the consumption of plutonium arising from spent fuel reprocessing. Although the same motivating factors apply in the case of boiling water reactors (BWRs), they have lagged behind PWRs for various reasons, and MOX utilisation in BWRs has been implemented in only a few reactors to date. One of the reasons is that the nuclear design of BWR MOX assemblies (or bundles) is more complex than that of PWR assemblies. Recognizing the need and the timeliness to address this issue at the international level, the OECD/NEA Working Party on the Physics of Plutonium Fuels and Innovative Fuel Cycles (WPPR) conducted a physics code benchmark test for a BWR assembly. This volume reports on the benchmark results and conclusions that can be drawn from it. (authors)

An integrated decision support system for wastewater nutrient recovery and recycling to agriculture

Science.gov (United States)

Roy, E. D.; Bomeisl, L.; Cornbrooks, P.; Mo, W.

2017-12-01

Nutrient recovery and recycling has become a key research topic within the wastewater engineering and nutrient management communities. Several technologies now exist that can effectively capture nutrients from wastewater, and innovation in this area continues to be an important research pursuit. However, practical nutrient recycling solutions require more than capable nutrient capture technologies. We also need to understand the role that wastewater nutrient recovery and recycling can play within broader nutrient management schemes at the landscape level, including important interactions at the nexus of food, energy, and water. We are developing an integrated decision support system that combines wastewater treatment data, agricultural data, spatial nutrient balance modeling, life cycle assessment, stakeholder knowledge, and multi-criteria decision making. Our goals are to: (1) help guide design decisions related to the implementation of sustainable nutrient recovery technology, (2) support innovations in watershed nutrient management that operate at the interface of the built environment and agriculture, and (3) aid efforts to protect aquatic ecosystems while supporting human welfare in a circular nutrient economy. These goals will be realized partly through the assessment of plausible alternative scenarios for the future. In this presentation, we will describe the tool and focus on nutrient balance results for the New England region. These results illustrate that both centralized and decentralized wastewater nutrient recovery schemes have potential to transform nutrient flows in many New England watersheds, diverting wastewater N and P away from aquatic ecosystems and toward local or regional agricultural soils where they can offset a substantial percentage of imported fertilizer. We will also highlight feasibility criteria and next steps to integrate stakeholder knowledge, economics, and life cycle assessment into the tool.

French programs for advanced waste management options

Energy Technology Data Exchange (ETDEWEB)

Salvatores, M [CEA-DRN (France); Schapira, J P [CNRS-IN2P3 (France); Mouney, H [EDF-DE (France)

1997-11-01

Several organisms (CEA, CNRS, EdF, etc.) are cooperating in France on Accelerator-Driven Systems (ADS). The major motivation is the investigation of innovative options for the radioactive waste management. The paper describes the ongoing activities and future directions of this cooperative effort in the field of ADS. 11 refs, 3 figs.

The New Option Offense for Winning Basketball.

Science.gov (United States)

Walker, A. L.; Donohue, Jack

This reference book for basketball coaches provides a total program of both offensive and defensive strategies and tactics. The emphasis is upon an innovative offensive system with an accompanying defensive plan. The initial chapters deal with the installation of the three series of the New Option Offensive: "Red,""White," and "Blue." A drills…

Recycle Alaska: Reduce, Reuse, Recycle. Activities Handbook, Teacher's Guide, and Student Worksheets.

Science.gov (United States)

Alaska State Dept. of Education, Juneau.

Recycling is a very important aspect of conserving the environment for future generations. This guide addresses the topic of litter prevention for the Alaskan environment and contains 42 activities. Activity topics covered include Natural Cycles, Human Interruption of Natural Cycles, Reduce, Reuse, Recycle and Recycled Classroom. Grade level,…

The Diffusion Effect of MSW Recycling

Directory of Open Access Journals (Sweden)

Yi-Tui Chen

2017-12-01

Full Text Available The purpose of this paper is to compare the recycling performance for some waste fractions selected including food waste, bulk waste, paper, metal products, plastics/rubber and glass products and then to develop some directions for the future improvements. The priority of each waste fraction for recycling is also analyzed by using an importance-performance analysis. Traditionally, the recycling rate that is calculated by the ratio of waste recycled to waste collected is used as an indicator to measure recycling performance. Due to a large variation among waste fractions in municipal solid waste (MSW, the recycling rate cannot reflect the actual recycling performance. The ceiling of recycling rate for each waste fraction estimated from the diffusion models is incorporated into a model to calculate recycling performance. The results show that (1 the diffusion effect exists significantly for the recycling of most recyclables but no evidence is found to support the diffusion effect for the recycling of food waste and bulk waste; (2 the recycling performance of waste metal products ranks the top, compared to waste paper, waste glass and other waste fractions; (3 furthermore, an importance-performance analysis (IPA is employed to analyze the priority of recycling programs and thus this paper suggests that the recycling of food waste should be seen as the most priority item to recycle.

Global architecture of innovative nuclear energy

International Nuclear Information System (INIS)

Andreeva-Andrievskaya, L.N.; Kagramanyan, V.S.; Usanov, V.I.; )

2011-01-01

The study Global Architecture of Innovative Nuclear Energy Systems Based on Thermal and Fast Reactors including a Closed Fuel Cycle (GAINS), aimed at harmonization of tools used to assess various options for innovative development of nuclear energy, modeling of jointly defined scenarios and analysis of obtained results is presented in the paper. Objectives and methods of the study, issues of spent fuel and fissile materials management are discussed. Investment risks and economic indicators are also described [ru

Innovation in the Open Data Ecosystem

DEFF Research Database (Denmark)

Jetzek, Thorhildur

2017-01-01

While open data as a phenomenon is rapidly growing up, innovation through open data is still less than expected. Research has shown that in spite of emerging new businesses models, private sector stakeholders are struggling to generate monetary income from open data. This is worrying as open data...... innovation and value generation in the open data ecosystem, and even resolve what we call the open data value paradox. We propose that governments, which openly publish data, are providing private sector stakeholders with the equivalent of a real option. By conceptualizing the uncertain or serendipitous...... value of open government data as option value, we might be able to stimulate activity and investment in the open data ecosystem. Moreover, we propose that by utilizing two-sided markets type of business models, private companies can use the data as a resource to provide free information...

The Fine Structure of Equity-Index Option Dynamics

DEFF Research Database (Denmark)

Andersen, Torben G.; Bondarenko, Oleg; Todorov, Viktor

We analyze the high-frequency dynamics of S&P 500 equity-index option prices by constructing an assortment of implied volatility measures. This allows us to infer the underlying fine structure behind the innovations in the latent state variables driving the movements of the volatility surface...

Innovation and creativity : Beyond diffusion

DEFF Research Database (Denmark)

Michelsen, Anders Ib

2009-01-01

of postwar systems theory and introduce Castoriadis' philosophy as an interesting option in this regard. It proceeds in four parts: (a) First, it debates the limits of the commonplace metaphor of diffusion and adoption in today's debate on innovation. (b) Second, it will present aspects of Castoriadis...

Compression Molding of Composite of Recycled HDPE and Recycled Tire Particles

Science.gov (United States)

Liu, Ping; Waskom, Tommy L.; Chen, Zhengyu; Li, Yanze; Peng, Linda

1996-01-01

Plastic and rubber recycling is an effective means of reducing solid waste to the environment and preserving natural resources. A project aimed at developing a new composite material from recycled high density polyethylene (HDPE) and recycled rubber is currently being conducted at Eastern Illinois University. The recycled plastic pellets with recycled rubber particles are extruded into some HDPE/rubber composite strands. The strand can be further cut into pellets that can be used to fabricate other material forms or products. This experiment was inspired by the above-mentioned research activity. In order to measure Durometer hardness of the extruded composite, a specimen with relatively large dimensions was needed. Thus, compression molding was used to form a cylindrical specimen of 1 in. diameter and 1 in. thickness. The initial poor quality of the molded specimen prompted a need to optimize the processing parameters such as temperature, holding time, and pressure. Design of experiment (DOE) was used to obtain optimum combination of the parameters.

Recycling and recovery of post-consumer plastic solid waste in a European context

Directory of Open Access Journals (Sweden)

Dewil Raf

2012-01-01

Full Text Available The disposal of waste plastics has become a major worldwide environmental problem. The USA, Europe and Japan generate annually about 50 million tons of post-consumer plastic waste, previously landfilled, generally considered as a non-sustainable and environmentally questionable option. Landfill sites and their capacity are, moreover, decreasing rapidly, and legislation is stringent. Several European Directives and US legislation concern plastic wastes and the required management. They are briefly discussed in this paper. New processes have emerged, i.e., advanced mechanical recycling of plastic waste as virgin or second grade plastic feedstock, and thermal treatments to recycle the waste as virgin monomer, as synthetic fuel gas, or as heat source (incineration with energy recovery. These processes avoid land filling, where the non-biodegradable plastics remain a lasting environmental burden. The paper reviews these alternative options through mostly thermal processing (pyrolysis, gasification and waste-to-energy. Additional research is, however, still needed to confirm the potential on pilot and commercial scale. [Acknowledgments. The research was partly funded by the Fundamental Research Funds for the Central Universities RC1101 (PR China and partly funded by Project KP/09/005 (SCORES4CHEM Knowledge Platform of the Industrial Research Council of the KU Leuven (Belgium.

FORWARD, FUTURE AND OPTIONS ON STOCK EXCHANGE MARKET

Directory of Open Access Journals (Sweden)

Ljiljana Stošić Mihajlović

2016-07-01

Full Text Available The main motive of the formation and use of forward contracts and futures, and options, was certainly profit. Making financial markets more efficient, in terms of expanding the range of available financial instruments and reduction in transaction costs, these financial innovations are beneficial for both investors and managers company. Primary purpose of derivatives such as forwards, futures and options is to enable control risks by investitures and primarily from inadequate price trends for all types of assets that could be subject to transactions in financial markets.

Policy options to stimulate social innovation initiatives addressing food waste prevention and reduction

NARCIS (Netherlands)

Vittuari, Matteo; Gaiani, Silvia; Politano, Alessandro; Timmermans, A.J.M.; Bos-Brouwers, H.E.J.

2016-01-01

The report builds on the knowledge created by the FUSIONS position paper “Stimulating social innovation through policy measures” that uses as key inputs the range of existing social innovation initiatives catalogued by FUSIONS WP4 in the inventory and draws on the outcomes of the WP3 Social Camp

Certified Electronics Recyclers

Science.gov (United States)

Learn how EPA encourages all electronics recyclers become certified by demonstrating to an accredited, independent third-party auditor and that they meet specific standards to safely recycle and manage electronics.

BWR Assembly Optimization for Minor Actinide Recycling

International Nuclear Information System (INIS)

Maldonado, G. Ivan; Christenson, John M.; Renier, J.P.; Marcille, T.F.; Casal, J.

2010-01-01

The Primary objective of the proposed project is to apply and extend the latest advancements in LWR fuel management optimization to the design of advanced boiling water reactor (BWR) fuel assemblies specifically for the recycling of minor actinides (MAs). A top-level objective of the Advanced Fuel Cycle Systems Analysis program element of the DOE NERI program is to investigate spent fuel treatment and recycling options for current light water reactors (LWRs). Accordingly, this project targets to expand the traditional scope of nuclear fuel management optimization into the following two complementary specific objectives: (1) To develop a direct coupling between the pin-by-pin within-bundle loading control variables and core-wide (bundle-by-bundle) optimization objectives, (2) to extend the methodology developed to explicitly encompass control variables, objectives, and constraints designed to maximize minor actinide incineration in BWR bundles and cycles. The first specific objective is projected to 'uncover' dormant thermal margin made available by employing additional degrees of freedom within the optimization process, while the addition of minor actinides is expected to 'consume' some of the uncovered thermal margin. Therefore, a key underlying goal of this project is to effectively invest some of the uncovered thermal margin into achieving the primary objective.

Socia preferences to Mopane woodland management options: A ...

African Journals Online (AJOL)

Socia preferences to Mopane woodland management options: A case study from Southern Zimbabwe. TA Gondo, C Musvoto, T Mujawo. Abstract. No Abstract. Discovery and Innovation Vol. 19 (1&2) 2007: pp.4-14. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

An innovative container supply chain for forest chips

Energy Technology Data Exchange (ETDEWEB)

Karttunen, Kalle; Korpinen, Olli-Jussi; Laettilae, Lauri; Foehr, Jarno; Ranta, Tapio [Lappeenranta Univ. of Technology, Mikkeli (Finland)], e-mail: kalle.karttunen@lut.fi

2012-11-01

Most forest chips are transported by trucks with a solid frame. Forest-chip volumes will at least double before 2020, which means longer transport distances from the supply areas to the largest demand sites in Finland. The study concentrates on an innovative container solution based on a channel composite structure, creating a lighter, temperature-isolated, and more durable structure. In addition to the structural benefits, the container includes an innovative supply chain with a beneficial handling operation, interchangeability and maximising of the payload capacity, resulting in an energy- and cost-efficient solution. This innovative-container-based supply chain for forest chips has been studied via cost analysis, GIS analysis, and discrete-event simulation methods. The purpose of the study was to compare a truck of interchangeable containers with solid-frame trucks. The option of interchangeable containers allows combining truck logistics with other modes of transport, such as trains and waterways. The study showed the cost-efficiency potential of container truck logistics, stemming from the cost and payload savings and the supply-chain productivity advantages over solid-frame trucks. The innovative solution for interchangeable-container logistics is an option for large-scale supply of forest chips.

Recycling of actinides and nuclear waste products. Annual report of the research programme 1997

International Nuclear Information System (INIS)

Konings, R.J.M.; Bakker, K.; Boerrigter, H.; Damen, P.G.M.; Gruppelaar, H.; Huntelaar, M.E.; Kloosterman, J.L.

1998-07-01

The research program on the title subject started in 1994 and is planned to be completed in 1998. In this period several technical and scientific aspects of recycling and transmutation are investigated in different projects. The results of the 1997 projects, carried out in the period July 1997 to June 1998, are summarized and described in this report. The 1997 projects concern (1) transmutation of actinides in inert matrices with the aim to design, test and characterize uranium-free fission materials for the transmutation of actinides, both for single as for multiple recycling strategies; (2) scenario studies for plutonium recycling with the aim to gain insight into the possibilities to reduce plutonium reserves by using plutonium as a fissionable material in reactors; (3) transmutation by means of accelerator-driven systems with the aim to analyze the options for the burning of plutonium in accelerator-driven, thorium-based systems; and (4) separation of actinides and lanthanides by means of Supported Liquid Membranes with the aim to study the possibility to extract americium from nuclear waste materials. refs

Economic Analysis of Different Nuclear Fuel Cycle Options

International Nuclear Information System (INIS)

Ko, W.; Gao, F.

2012-01-01

An economic analysis has been performed to compare four nuclear fuel cycle options: a once-through cycle (OT), DUPIC recycling, thermal recycling using MOX fuel in a pressurized water reactor (PWR-MOX), and sodium fast reactor recycling employing pyro processing (Pyro-SFR). This comparison was made to suggest an economic competitive fuel cycle for the Republic of Korea. The fuel cycle cost (FCC) has been calculated based on the equilibrium material flows integrated with the unit cost of the fuel cycle components. The levelized fuel cycle costs (LFCC) have been derived in terms of mills/kWh for a fair comparison among the FCCs, and the results are as follows: OT 7.35 mills/kWh, DUPIC 9.06 mills/kWh, PUREX-MOX 8.94 mills/kWh, and Pyro-SFR 7.70 mills/kWh. Due to unavoidable uncertainties, a cost range has been applied to each unit cost, and an uncertainty study has been performed accordingly. A sensitivity analysis has also been carried out to obtain the break-even uranium price (215$/kgU) for the Pyro-SFR against the OT, which demonstrates that the deployment of the Pyro-SFR may be economical in the foreseeable future. The influence of pyro techniques on the LFCC has also been studied to determine at which level the potential advantages of Pyro-SFR can be realized.

PET and Recycling

Directory of Open Access Journals (Sweden)

Funda Sevencan

2007-08-01

Full Text Available This review aims to clarify the need of decreasing the environmental effects caused by human and draw attention to the increasing environmental effects of plastics wastes. Plastics consist of organic molecules with high density molecules or polymers. Main resources of plastics are the residue of oil rafineries. Several advantages of plastics, have increased the usage continuously. Polyethylene Terephthalate (PET is the most commonly used plastics. PET is used to protect food, drinking water, fruit juice, alcoholic beverage, and food packing films. By the increasing interest on the environmental effects of plastic wastes, concerns on the recyclable packing materials also grew up. Also the daily use of recyclable containers consisting PET have increased. There are five steps for recycling of plastics. These steps are; using large amounts of plastics, collecting them in a big center, classifying and sorting the plastics, reproducing the polymers and obtaining new products with melted plastics. Providing a healthy recycling of plastics, the consumers should have knowledge and responsibility. The consumer should know what he/she has to do before putting the plastics in the recycling containers. Recycling containers and bags should be placed near the sources of plastic wastes. Consequently, the plastic wastes and environmental problems they cause will be on the agenda in future. [TAF Prev Med Bull. 2007; 6(4: 307-312

PET and Recycling

Directory of Open Access Journals (Sweden)

Funda Sevencan

2007-08-01

Full Text Available This review aims to clarify the need of decreasing the environmental effects caused by human and draw attention to the increasing environmental effects of plastics wastes. Plastics consist of organic molecules with high density molecules or polymers. Main resources of plastics are the residue of oil rafineries. Several advantages of plastics, have increased the usage continuously. Polyethylene Terephthalate (PET is the most commonly used plastics. PET is used to protect food, drinking water, fruit juice, alcoholic beverage, and food packing films. By the increasing interest on the environmental effects of plastic wastes, concerns on the recyclable packing materials also grew up. Also the daily use of recyclable containers consisting PET have increased. There are five steps for recycling of plastics. These steps are; using large amounts of plastics, collecting them in a big center, classifying and sorting the plastics, reproducing the polymers and obtaining new products with melted plastics. Providing a healthy recycling of plastics, the consumers should have knowledge and responsibility. The consumer should know what he/she has to do before putting the plastics in the recycling containers. Recycling containers and bags should be placed near the sources of plastic wastes. Consequently, the plastic wastes and environmental problems they cause will be on the agenda in future. [TAF Prev Med Bull 2007; 6(4.000: 307-312

Reusing and recycling in Saskatchewan: Environmental benefits of reusing and recycling

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

After an introduction explaining the environmental benefits of reusing and recycling, as well as providing suggestions on minimizing waste and conserving energy, a directory of recyclers and handlers of various kinds of waste in Saskatchewan is presented. Names, addresses/telephone numbers, and types of materials accepted are given for recyclers of animal products, clothing or textiles, glass, compostable materials, industrial hardware, metals, office products, paper, plastic, and tires. Collection depots in the SARCAN recycling program for beverage containers are listed, giving town name, address, hours of operation, and telephone number. Receivers of waste dangerous goods are listed under the categories of ozone-depleting substances, waste batteries, solvents, lubricating oils and oil filters, paint, flammable liquids, antifreeze, drycleaning waste, and miscellaneous.

Recycling of Paper and Cardboard

DEFF Research Database (Denmark)

Christensen, Thomas Højlund; Damgaard, Anders

2011-01-01

waste. Recycling of paper and cardboard production waste and postconsumer waste has a long history in the pulp and paper industry. The recycled material now makes up more than half of the raw material used in European pulp and paper industry (ERPC, 2004). This chapter describes briefly how paper...... and cardboard are produced and how waste paper is recycled in the industry. Quality requirements and use of recycled products are discussed, as are the resource and environmental issues of paper recycling....

Water Recycling in Australia

Directory of Open Access Journals (Sweden)

Ross Young

2011-09-01

Full Text Available Australia is the driest inhabited continent on earth and, more importantly, experiences the most variable rainfall of all the continents on our planet. The vast majority of Australians live in large cities on the coast. Because wastewater treatments plants were all located near the coast, it was thought that large scale recycling would be problematic given the cost of infrastructure and pumping required to establish recycled water schemes. This all changed when Australia experienced a decade of record low rainfall and water utilities were given aggressive targets to increase the volume of water recycled. This resulted in recycled water being accepted as a legitimate source of water for non-drinking purposes in a diversified portfolio of water sources to mitigate climate risk. To ensure community support for recycled water, Australia lead the world in developing national guidelines for the various uses of recycled water to ensure the protection of public health and the environment. Australia now provides a great case study of the developments in maximizing water recycling opportunities from policy, regulatory and technological perspectives. This paper explores the evolution in thinking and how approaches to wastewater reuse has changed over the past 40 years from an effluent disposal issue to one of recognizing wastewater as a legitimate and valuable resource. Despite recycled water being a popular choice and being broadly embraced, the concept of indirect potable reuse schemes have lacked community and political support across Australia to date.

Recycling of concrete

International Nuclear Information System (INIS)

Halaszovich, S.

1988-01-01

The paper reviews potentials and problems of disposal or recycling of concrete removed from nuclear installations. Due to the difficulties in determining radioactivity limits that are compatible with utilization of recycled material in practice, a method is proposed that takes into account inhalation of dusts, as occurring during the reprocessing or recycling of the concrete, for instance in road building. This method is based on the maximum permissible radioactivity uptake by inhalation of a nuclide mixture of unknown composition. (RB) [de

Aluminium beverage can recycling

Energy Technology Data Exchange (ETDEWEB)

Lewinski, A von

1985-08-01

Canned beverages have become a controversial issue in this era of ecological sensitivity. METALL has already discussed the problem of can recycling. The present article discusses the technical aspects of aluminium can recycling. Two further articles will follow on aluminium can recycling in North America and on the results of European pilot projects.

Environmental assessment of different management options for individual waste fractions by means of life-cycle assessment modelling

DEFF Research Database (Denmark)

Manfredi, Simone; Tonini, Davide; Christensen, Thomas Højlund

2011-01-01

and environmental factors involved, including energy generation from landfill gas and storage of biogenic carbon. Leachate and gas emissions associated to each individual waste fraction have been estimated by means of a mathematical modelling. This approach towards landfilling emissions allows for a more precise...... quantification of the landfill impacts when comparing management options for selected waste fractions.Results from the life-cycle impact assessment (LCIA) show that the environmental performance estimated for landfilling with energy recovery of the fractions “organics” and “recyclable paper” is comparable...... with composting (for “organics”) and incineration (for “recyclable paper”). This however requires high degree of control over gas and leachate emissions, high gas collection efficiency and extensive gas utilization at the landfill. For the other waste fractions, recycling and incineration are favourable, although...

Innovation and energy. ECRIN day

International Nuclear Information System (INIS)

2004-01-01

ECRIN is an association jointly created by the French atomic energy commission (CEA) and the French national center of scientific research (CNRS). It gathers experts from the research and industry worlds, representatives of institutions and decision making peoples in order to work on important topics like energy. This document gathers the working documents and transparencies presented at the ECRIN day on energy and innovation: opening talk of C. Birraux (head of the parliamentary office of evaluation of scientific and technological choices); the energy of seas (offshore wind power, wave energy, tide currents energy, thermal energy of seas, osmotic energy, tidal energy); synthetic fuels (stakes, possible options, Fischer-Tropsch synthesis, GTL, CTL, BTL, production with CO 2 recycling); capture and geological sequestration of CO 2 : a general overview (stakes, solutions, capture and sequestration, transport, geologic disposal, present day situation and perspectives); geothermal energy: new prospects (enhanced geothermal systems, hot-dry-rocks and hot fractured rocks, advances, cost, advantages and drawbacks); heat pumps and valorization of low temperature heat sources (space heating, district heating networks, heat pumps, artificial geothermal energy, low temperature water transport, thermal potentiality); heat and coldness storage and transport (use of intermittent energy sources, cogeneration, optimisation of processes, recovery of heat losses, CO 2 capture, present-day situation, problems to be solved, integration of systems and processes); plastic photovoltaic solar cells (market, stakes, potentialities of organic materials for photovoltaic conversion, state-of-the-art, research in Europe and France, perspectives); conclusion of the Ecrin day (challenges, diversification of energy sources, energy efficiency, abatement of CO 2 emissions, role of ECRIN). (J.S.)

Evaluation of the recycling costs, as a disposal form of the spent nuclear fuel

International Nuclear Information System (INIS)

Ramirez S, J.R.; Alonso V, G.; Palacios, J.C.

2006-01-01

At the moment there are 2 BWR reactors operating in the Nuclear Power station of Laguna Verde in Mexico. At the end of the programmed life of the reactors (40 years) its will have completed 26 operation cycles, with will have 6712 spent fuel assemblies will be in the pools of the power station. Up to now, the decision on the destination of the high level wastes (spent nuclear fuel) it has not been determined in Mexico, the same as in other countries, adopting a politics of 'to wait to see that it happens in the world', in this respect, in the world two practical alternatives exist, one is to store the fuel in repositories designed for that end, another is reprocess the fuel to recycle the plutonium contained in it, both solutions have their particular technical and economic problematic. In this work it is evaluated from the economic point of view the feasibility of having the spent fuel, using the one recycled fuel, for that which thinks about a consistent scenario of a BWR reactor in which the fuel discharged in each operation cycle is reprocessed and its are built fuel assemblies of the MOX type to replace partly to the conventional fuel. This scenario shows an alternative to the indefinite storage of the high level radioactive waste. The found results when comparing from the economic point of view both options, show that the one recycled, even with the current costs of the uranium it is of the order of 7% more expensive that the option of storing the fuel in repositories constructed for that purpose. However the volumes of spent fuel decrease in 66%. (Author)

Achieving Nuclear Sustainability through Innovation

International Nuclear Information System (INIS)

2013-01-01

In 2000, the IAEA Member States recognized that concerted and coordinated research and development is needed to drive innovation that ensures that nuclear energy can help meet energy needs sustainably in the 21st century. Following an IAEA General Conference resolution, an international 'think tank' and dialogue forum were established. The resulting organization, the IAEA's International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO), helps nuclear technology holders and users coordinate the national and international studies, research and other activities needed to achieve innovations in nuclear reactor designs and fuel cycles. Currently, 38 countries plus the European Commission are participating in the project. This group includes both developing and developed economies that represent more than 75% of the world's population and 85% of its gross domestic product. INPRO undertakes collaborative projects among IAEA Member States, which analyse development scenarios and examine how nuclear energy can support the United Nations' goals for sustainable development in the 21st century. The results of these projects can be applied by IAEA Member States in their national nuclear energy strategies and can lead to international cooperation resulting in beneficial innovations in nuclear energy technology and its deployment. For example, INPRO studies the 'back end' of the fuel cycle, including recycling of spent fuel to increase resource use efficiency and to reduce the waste disposal burdens.

The recycling is moving

CERN Multimedia

GS Department

2011-01-01

The recycling site currently situated near building 133 has been transferred to the car park of building 156. The site is identified by the sign “RECYCLING” and the above logo. In this new, more accessible site, you will find recycling bins for the following waste: PET (recyclable plastic bottles); Aluminium cans; Nespresso coffee capsules.  

An experimental school prototype: Integrating 3rs (reduce, reuse & recycle) concept into architectural design

OpenAIRE

Kong Seng Yeap; Sreenivasaiah Purushothama Rao

2012-01-01

The authors conducted a design project to examine the use of school as an ecological learning hub for children. Specifically, this study explores the ecological innovations that transform physical environment into three-dimensional textbooks for environmental education. A series of design workshops were carried out to gain interdisciplinary input for ecological school design. The findings suggest to integrate the concept of 3Rs (Reduce, Reuse & Recycle) into the physical environment. As a res...

Economic Feasibility for Recycling of Waste Crystalline Silicon Photovoltaic Modules

Directory of Open Access Journals (Sweden)

Idiano D’Adamo

2017-01-01

Full Text Available Cumulative photovoltaic (PV power installed in 2016 was equal to 305 GW. Five countries (China, Japan, Germany, the USA, and Italy shared about 70% of the global power. End-of-life (EoL management of waste PV modules requires alternative strategies than landfill, and recycling is a valid option. Technological solutions are already available in the market and environmental benefits are highlighted by the literature, while economic advantages are not well defined. The aim of this paper is investigating the financial feasibility of crystalline silicon (Si PV module-recycling processes. Two well-known indicators are proposed for a reference 2000 tons plant: net present value (NPV and discounted payback period (DPBT. NPV/size is equal to −0.84 €/kg in a baseline scenario. Furthermore, a sensitivity analysis is conducted, in order to improve the solidity of the obtained results. NPV/size varies from −1.19 €/kg to −0.50 €/kg. The absence of valuable materials plays a key role, and process costs are the main critical variables.

Regular Recycling of Wood Ash to Prevent Waste Production (RecAsh). Technical Final Report

Energy Technology Data Exchange (ETDEWEB)

Andersson, Lars E-mail: lars.t.andersson@skogsstyreslen.se

2007-03-15

At present, the extraction of harvest residues is predicted to increase in Sweden and Finland. As an effect of the intensified harvesting, the export of nutrients and acid buffering substances from the growth site is also increased. Wood ash could be used to compensate forest soils for such losses. Most wood fuel ash is today often deposited in landfills. If the wood ash is recycled, wood energy is produced without any significant waste production. Ash recycling would therefore contribute to decreasing the production of waste, and to maintaining the chemical quality of forest waters and biological productivity of forest soils in the long term. The project has developed, analysed and demonstrated two regular ash-recycling systems. It has also distributed knowledge gathered about motives for ash recycling as well as technical and administrative solutions through a range of media (handbooks, workshops, field demonstrations, reports, web page and information videos). Hopefully, the project will contribute to decreasing waste problems related to bio-energy production in the EU at large. The project has been organised as a separate structure at the beneficiary and divided in four geographically defined subprojects, one in Finland and three in Sweden (Central Sweden, Northern Sweden, and South-western Sweden). The work in each subproject has been lead by a subproject leader. Each subproject has organised a regional reference group. A project steering committee has been established consisting of senior officials from all concerned partners. The project had nine main tasks with the following main expected deliverables and output: 1. Development of two complete full-scale ash-recycling systems; 2. Production of handbooks of the ash recycling system; 3. Ash classification study to support national actions for recommendations; 4. Organise regional demonstrations of various technical options for ash treatment and spreading; 5. Organise national seminars and demonstrations of

Designing the Reverse Supply Chain

DEFF Research Database (Denmark)

Gobbi, Chiara

2011-01-01

Purpose – The purpose of this paper is to explore the impact of the product residual value (PRV) and the loss of value over time of returned products in the reverse supply chain configuration. It also examines whether or not the distinction of Fisher's functional and innovative products holds...... that allows for recapturing most of the PRV. These notions have then been tested by analyzing two reverse supply chains with a case study research methodology. Findings – The findings show that low PRV is associated with second-class recovery options (recycling and energy recovery) and that high PRV...... is associated with first-class recovery options (reconditioning and remarketing). When the recovery option is recycling, time is not relevant, the primary objective is cost reduction (efficiency), the chain is centralized, and actors and phases of the reverse chain are determined by the specificity...

A Perspective on the Prowaste Concept: Efficient Utilization of Plastic Waste through Product Design and Process Innovation.

Science.gov (United States)

Greco, Antonio; Frigione, Mariaenrica; Maffezzoli, Alfonso; Marseglia, Alessandro; Passaro, Alessandra

2014-07-23

This work is aimed to present an innovative technology for the reinforcement of beams for urban furniture, produced by in-mold extrusion of plastics from solid urban waste. This material, which is usually referred to as "recycled plastic lumber", is characterized by very poor mechanical properties, which results in high deflections under flexural loads, particularly under creep conditions. The Prowaste project, founded by the EACI (European Agency for Competitiveness and Innovation) in the framework of the Eco-Innovation measure, was finalized to develop an innovative technology for selective reinforcement of recycled plastic lumber. Selective reinforcement was carried out by the addition of pultruded glass rods in specific positions with respect to the cross section of the beam, which allowed optimizing the reinforcing efficiency. The reinforcement of the plastic lumber beams with pultruded rods was tested at industrial scale plant, at Solteco SL (Alfaro, Spain). The beams obtained, characterized by low cost and weight, were commercialized by the Spanish company. The present paper presents the most relevant results of the Prowaste project. Initially, an evaluation of the different materials candidates for the reinforcement of recycled plastic lumber is presented. Plastic lumber beams produced in the industrial plant were characterized in terms of flexural properties. The results obtained are interpreted by means of beam theory, which allows for extrapolation of the characteristic features of beams produced by different reinforcing elements. Finally, a theoretical comparison with other approaches which can be used for the reinforcement of plastic lumber is presented, highlighting that, among others, the Prowaste concept maximizes the stiffening efficiency, allowing to significantly reduce the weight of the components.

A Critical Review of the Recent Improvements in Minimizing Nuclear Waste by Innovative Gas-Cooled Reactors

Directory of Open Access Journals (Sweden)

E. Bomboni

2008-01-01

Full Text Available This paper presents a critical review of the recent improvements in minimizing nuclear waste in terms of quantities, long-term activities, and radiotoxicities by innovative GCRs, with particular emphasis to the results obtained at the University of Pisa. Regarding these last items, in the frame of some EU projects (GCFR, PUMA, and RAPHAEL, we analyzed symbiotic fuel cycles coupling current LWRs with HTRs, finally closing the cycle by GCFRs. Particularly, we analyzed fertile-free and Pu-Th-based fuel in HTR: we improved plutonium exploitation also by optimizing Pu/Th ratios in the fuel loaded in an HTR. Then, we chose GCFRs to burn residual MA. We have started the calculations on simplified models, but we ended them using more “realistic” models of the reactors. In addition, we have added the GCFR multiple recycling option using keff calculations for all the reactors. As a conclusion, we can state that, coupling HTR with GCFR, the geological disposal issues concerning high-level radiotoxicity of MA can be considerably reduced.

Radiological impacts of spent nuclear fuel management options

International Nuclear Information System (INIS)

Riotte, H.; Lazo, T.; Mundigl, S.

2000-01-01

An important technical study on radiological impacts of spent nuclear fuel management options, recently completed by the NEA, is intended to facilitate informed international discussions on the nuclear fuel cycle. The study compares the radiological impacts on the public and on nuclear workers resulting from two approaches to handling spent fuel from nuclear power plants: - the reprocessing option, that includes the recycling of spent uranium fuel, the reuse of the separated plutonium in MOX fuel, and the direct disposal of spent MOX fuel; and the once-through option, with no reprocessing of spent fuel, and its direct disposal. Based on the detailed research of a group of 18 internationally recognised experts, under NEA sponsorship, the report concludes that: The radiological impacts of both the reprocessing and the non-reprocessing fuel cycles studied are small, well below any regulatory dose limits for the public and for workers, and insignificantly low as compared with exposures caused by natural radiation. The difference in the radiological impacts of the two fuel cycles studied does not provide a compelling argument in favour of one option or the other. The study also points out that other factors, such as resource utilisation efficiency, energy security, and social and economic considerations would tend to carry more weight than radiological impacts in decision-making processes. (authors)

Tire Recycling

Science.gov (United States)

1997-01-01

Cryopolymers, Inc. tapped NASA expertise to improve a process for recycling vehicle tires by converting shredded rubber into products that can be used in asphalt road beds, new tires, hoses, and other products. In conjunction with the Southern Technology Applications Center and Stennis Space Center, NASA expertise in cryogenic fuel-handling needed for launch vehicle and spacecraft operations was called upon to improve the recycling concept. Stennis advised Cryopolymers on the type of equipment required, as well as steps to reduce the amount of liquid nitrogen used in the process. They also guided the company to use more efficient ways to control system hardware. It is estimated that more than 300 million tires nationwide are produced per year. Cryopolymers expects to reach a production rate of 5,000 tires recycled per day.

Recycle Glass in Foam Glass Production

DEFF Research Database (Denmark)

Petersen, Rasmus Rosenlund; König, Jakob; Yue, Yuanzheng

The foam glass industry turn recycle glass into heat insulating building materials. The foaming process is relative insensitive to impurities in the recycle glass. It is therefore considered to play an important role in future glass recycling. We show and discuss trends of use of recycled glasses...... in foam glass industry and the supply sources and capacity of recycle glass....

Auditing an intensive care unit recycling program.

Science.gov (United States)

Kubicki, Mark A; McGain, Forbes; O'Shea, Catherine J; Bates, Samantha

2015-06-01

The provision of health care has significant direct environmental effects such as energy and water use and waste production, and indirect effects, including manufacturing and transport of drugs and equipment. Recycling of hospital waste is one strategy to reduce waste disposed of as landfill, preserve resources, reduce greenhouse gas emissions, and potentially remain fiscally responsible. We began an intensive care unit recycling program, because a significant proportion of ICU waste was known to be recyclable. To determine the weight and proportion of ICU waste recycled, the proportion of incorrect waste disposal (including infectious waste contamination), the opportunity for further recycling and the financial effects of the recycling program. We weighed all waste and recyclables from an 11-bed ICU in an Australian metropolitan hospital for 7 non-consecutive days. As part of routine care, ICU waste was separated into general, infectious and recycling streams. Recycling streams were paper and cardboard, three plastics streams (polypropylene, mixed plastics and polyvinylchloride [PVC]) and commingled waste (steel, aluminium and some plastics). ICU waste from the waste and recycling bins was sorted into those five recycling streams, general waste and infectious waste. After sorting, the waste was weighed and examined. Recycling was classified as achieved (actual), potential and total. Potential recycling was defined as being acceptable to hospital protocol and local recycling programs. Direct and indirect financial costs, excluding labour, were examined. During the 7-day period, the total ICU waste was 505 kg: general waste, 222 kg (44%); infectious waste, 138 kg (27%); potentially recyclable waste, 145 kg (28%). Of the potentially recyclable waste, 70 kg (49%) was actually recycled (14% of the total ICU waste). In the infectious waste bins, 82% was truly infectious. There was no infectious contamination of the recycling streams. The PVC waste was 37% contaminated

A comparative study on recycling spent fuels in gas-cooled fast reactors

International Nuclear Information System (INIS)

Choi, Hangbok; Baxter, Alan

2010-01-01

This study evaluates advanced Gas-cooled Fast Reactor (GFR) fuel cycle scenarios which are based on recycling spent nuclear fuel for the sustainability of nuclear energy. A 600 MWth GFR was used for the fuel cycle analysis, and the equilibrium core was searched with different fuel-to-matrix volume ratios such as 70/30 and 60/40. Two fuel cycle scenarios, i.e., a one-tier case combining a Light Water Reactor (LWR) and a GFR, and a two-tier case using an LWR, a Very High Temperature Reactor (VHTR), and a GFR, were evaluated for mass flow and fuel cycle cost, and the results were compared to those of LWR once-through fuel cycle. The mass flow calculations showed that the natural uranium consumption can be reduced by more than 57% and 27% for the one-tier and two-tier cycles, respectively, when compared to the once-through fuel cycle. The transuranics (TRU) which pose a long-term problem in a high-level waste repository, can be significantly reduced in the multiple recycle operation of these options, resulting in more than 110 and 220 times reduction of TRU inventory to be geologically disposed for the one-tier and two-tier fuel cycles, respectively. The fuel cycle costs were estimated to be 9.4 and 8.6 USD/MWh for the one-tier fuel cycle when the GFR fuel-to-matrix volume ratio was 70/30 and 60/40, respectively. However the fuel cycle cost is reduced to 7.3 and 7.1 USD/MWh for the two-tier fuel cycle, which is even smaller than that of the once-through fuel cycle. In conclusion the GFR can provide alternative fuel cycle options to the once-through and other fast reactor fuel cycle options, by increasing the natural uranium utilization and reducing the fuel cycle cost.

Fast Reactor Systems and Innovative Fuels for Minor Actinides Homogeneous Recycling

International Nuclear Information System (INIS)

Calabrese, R.

2013-01-01

The capability of nuclear energy source to limit GHG emissions at a competitive cost is still a potential driver for its development in the near- and medium-term. The sustainability of nuclear energy is concerned by various issues such as the shortage of natural uranium resources, the management of steadily increasing inventories of spent nuclear fuel as well as competitiveness. Nuclear technology should be, for its societal acceptability, affordable, safe and featured by low proliferation risks. In this regard innovative fast reactors could improve the management of spent nuclear fuel inventories a reducing the burden on the geological repository. The development of MA-bearing oxide fuels is ongoing both on the definition of under-irradiation behaviour as well as the investigations of new fabrication routes and significant efforts in R&D are necessary. This paper confirms the expected performance of investigated FRs and the synergistic use of NFCSS and DESAE proved to be capable in modelling with reasonable accuracy an innovative fuel cycle strategy. The reduction of GHG emissions by means of a steep expansion of nuclear energy needs to be carefully investigated where a multi-criteria approach is of crucial importance

Recycling of Metals

DEFF Research Database (Denmark)

Damgaard, Anders; Christensen, Thomas Højlund

2011-01-01

Metals like iron and aluminium are produced from mineral ore and used for a range of products, some of which have very short lifetimes and thus constitute a major fraction of municipal waste. Packaging in terms of cans, foils and containers are products with a short lifetime. Other products like...... appliances, vehicles and buildings, containing iron and aluminium metals, have long lifetimes before they end up in the waste stream. The recycling of production waste and postconsumer metals has a long history in the metal industry. Some metal smelters are today entirely based on scarp metals. This chapter...... describes briefly how iron and aluminium are produced and how scrap metal is recycled in the industry. Quality requirements and use of recycled products are discussed, as are the resource and environmental issues of metal recycling. Copper and other metals are also found in waste but in much smaller...

Nuclear reactor recyclation device

International Nuclear Information System (INIS)

Takigawa, Yukio; Chuma, Kazuto

1987-01-01

Purpose: To prevent the unevenness for the coolant flow rate even when abnormality occurs to one of recycling pumps. Constitution: A plurality of jet pumps disposed at an interval around the reactor core are divided circumferentially into two sets, and a pipeway is disposed to the outside of each pair including recycling pumps corresponding to each of the sets. The pipeway is connected to the recycling inlet of the jet pump by way of a manifold. The discharge portion of the recycling pumps of the loop pipeway are connected with each other by way of communication pipes, and a normally closed valve is disposed to the communication pipe and the normally closed valve of the communication pipe is opened upon detecting abnormality for one of the recycling pumps. Thus, if either one of the pair of recycling pumps shows abnormal state, coolants flows from the other of pipeway to the outside of the loop pipeway and coolants are supplied from all the jet pumps to the reactor core portion and, accordingly, the not-uniform flow rate can be prevented to eliminate undesired effect on the reactor core. (Kamimura, M.)

Recycling - Danish Waste Management Strategy

DEFF Research Database (Denmark)

Romann, Anne Funch; Thøgersen, John; Husmer, Lis

The report challanges recycling as the only waste handling strategy. The tonnes of recycled materials should not be the only goal - it is essential to minimize the waste production and focus on eliminating hazardous materials.......The report challanges recycling as the only waste handling strategy. The tonnes of recycled materials should not be the only goal - it is essential to minimize the waste production and focus on eliminating hazardous materials....

Length sensing and control of a Michelson interferometer with power recycling and twin signal recycling cavities.

Science.gov (United States)

Gräf, Christian; Thüring, André; Vahlbruch, Henning; Danzmann, Karsten; Schnabel, Roman

2013-03-11

The techniques of power recycling and signal recycling have proven as key concepts to increase the sensitivity of large-scale gravitational wave detectors by independent resonant enhancement of light power and signal sidebands within the interferometer. Developing the latter concept further, twin signal recycling was proposed as an alternative to conventional detuned signal recycling. Twin signal recycling features the narrow-band sensitivity gain of conventional detuned signal recycling but furthermore facilitates the injection of squeezed states of light, increases the detector sensitivity over a wide frequency band and requires a less complex detection scheme for optimal signal readout. These benefits come at the expense of an additional recycling mirror, thus increasing the number of degrees of freedom in the interferometer which need to be controlled.In this article we describe the development of a length sensing and control scheme and its successful application to a tabletop-scale power recycled Michelson interferometer with twin signal recycling. We were able to lock the interferometer in all relevant longitudinal degrees of freedom and thus laid the foundation for further investigations of this interferometer configuration to evaluate its viability for the application in gravitational wave detectors.

Scenarios for waste management involving innovative systems (ADS)

International Nuclear Information System (INIS)

Tommasi, J.; Bottollier-Curtet, H.; Massara, S.; Varaine, F.; Delpech, M.

2001-01-01

The global performance of reactor park scenarios based on innovative systems (Accelerator-Driven Systems, ADS) for transmutation is studied, based either on equilibrium recycling states or on high burn-up systems. The results of these first studies are preliminary but allow to assess the main parameters of the fuel cycle (inventories, mass balances, mass flows...), to evaluate the specific contributions of ADS on the main scenario parameters, and to compare subcritical systems to critical ones. (author)

Nuclear recycling: costs, savings, and safeguards

International Nuclear Information System (INIS)

Spinrad, B.I.

1985-01-01

This chapter discusses the economics, physical and chemical processes, and safety of nuclear fuel recycling. The spent fuel must be chemically reprocessed in order to recover uranium and plutonium. Topics considered include indifference costs, recycling in light water reactors (LWRs), plutonium in fast reactors, the choice between recycling and storage, safeguards, and weapons proliferation. It is shown that the economics of recycling nuclear fuel involves the actual costs and savings of the recycling operation in terms of money spent, made, and saved, and the impact of the recycling on the future cost of uranium

Benchmarking survey for recycling.

Energy Technology Data Exchange (ETDEWEB)

Marley, Margie Charlotte; Mizner, Jack Harry

2005-06-01

This report describes the methodology, analysis and conclusions of a comparison survey of recycling programs at ten Department of Energy sites including Sandia National Laboratories/New Mexico (SNL/NM). The goal of the survey was to compare SNL/NM's recycling performance with that of other federal facilities, and to identify activities and programs that could be implemented at SNL/NM to improve recycling performance.

Centralized consolidation/recycling center

International Nuclear Information System (INIS)

St. Georges, L.T.; Poor, A.D.

1995-05-01

There are approximately 175 separate locations on the Hanford Site where dangerous waste is accumulated in hundreds of containers according to compatibility. Materials that are designated as waste could be kept from entering the waste stream by establishing collection points for these materials and wastes and then transporting them to a centralized consolidation/recycling center (hereinafter referred to as the consolidation center). Once there the materials would be prepared for offsite recycling. This document discusses the removal of batteries, partially full aerosol cans, and DOP light ballasts from the traditional waste management approach, which eliminates 89 satellite accumulation areas from the Hanford Site (43 for batteries, 33 for aerosols, and 13 for DOP ballasts). Eliminating these 89 satellite accumulation areas would reduce by hundreds the total number of containers shipped offsite as hazardous waste (due to the increase in containers when the wastes that are accumulated are segregated according to compatibility for final shipment). This new approach is in line with the U.S. Environmental Protection Agency's (EPA) draft Universal Waste Rules for these open-quotes nuisanceclose quotes and common waste streams. Additionally, future reviews of other types of wastes that can be handled in this less restrictive and more cost-effective manner will occur as part of daily operations at the consolidation center. The Hanford Site has been identified as a laboratory for reinventing government by the Secretary of the U.S. Department of Energy (DOE), Hazel O'Leary, and as a demonstration zone where open-quotes innovative ideas, processes and technologies can be created, tested and demonstrated.close quotes Additionally, DOE, EPA, and the Washington State Department of Ecology (Ecology) have agreed to cut Hanford cleanup costs by $1 billion over a 5-year period

Resource Efficient Metal and Material Recycling

Science.gov (United States)

Reuter, Markus A.; van Schaik, Antoinette

Metals enable sustainability through their use and their recyclability. However, various factors can affect the Resource Efficiency of Metal Processing and Recycling. Some typical factors that enable Resource Efficiency include and arranged under the drivers of sustainability: Environment (Maximize Resource Efficiency — Energy, Recyclates, Materials, Water, Sludges, Emissions, Land); Economic Feasibility (BAT & Recycling Systems Simulation / Digitalization, Product vis-à-vis Material Centric Recycling); and Social — Licence to Operate (Legislation, consumer, policy, theft, manual labour.). In order to realize this primary production has to be linked systemically with typical actors in the recycling chain such as Original Equipment Manufacturers (OEMs), Recyclers & Collection, Physical separation specialists as well as process metallurgical operations that produce high value metals, compounds and products that recycle back to products. This is best done with deep knowledge of multi-physics, technology, product & system design, process control, market, life cycle management, policy, to name a few. The combination of these will be discussed as Design for Sustainability (DfS) and Design for Recycling (DfR) applications.

Strategic Orientation Towards Sustainable Innovation: A Case Study in a Brazilian University

Directory of Open Access Journals (Sweden)

Mauri Leodir Löbler

2012-07-01

Full Text Available The technological development that results from innovation can lead to considerable environmental impact. Yet, companies and other stakeholders have not done enough to develop strategies for minimizing waste management. The present study contributes to research in this area, by empirically examining the link between the management of technological innovation and sustainability. A case study was carried out to examine the extent to which there is strategic orientation towards both technological innovation and sustainability in a large public university in Brazil. The results show the importance of integrating sustainability activities within the organisation’s corporate strategy: although the researched organisation had sufficient theoretical knowledge about waste management, the lack of an integrated strategy led to uncoordinated attempts at recycling within the university.

Spent fuel reprocessing options

International Nuclear Information System (INIS)

2008-08-01

The objective of this publication is to provide an update on the latest developments in nuclear reprocessing technologies in the light of new developments on the global nuclear scene. The background information on spent fuel reprocessing is provided in Section One. Substantial global growth of nuclear electricity generation is expected to occur during this century, in response to environmental issues and to assure the sustainability of the electrical energy supply in both industrial and less-developed countries. This growth carries with it an increasing responsibility to ensure that nuclear fuel cycle technologies are used only for peaceful purposes. In Section Two, an overview of the options for spent fuel reprocessing and their level of development are provided. A number of options exist for the treatment of spent fuel. Some, including those that avoid separation of a pure plutonium stream, are at an advanced level of technological maturity. These could be deployed in the next generation of industrial-scale reprocessing plants, while others (such as dry methods) are at a pilot scale, laboratory scale or conceptual stage of development. In Section Three, research and development in support of advanced reprocessing options is described. Next-generation spent fuel reprocessing plants are likely to be based on aqueous extraction processes that can be designed to a country specific set of spent fuel partitioning criteria for recycling of fissile materials to advanced light water reactors or fast spectrum reactors. The physical design of these plants must incorporate effective means for materials accountancy, safeguards and physical protection. Section four deals with issues and challenges related to spent fuel reprocessing. The spent fuel reprocessing options assessment of economics, proliferation resistance, and environmental impact are discussed. The importance of public acceptance for a reprocessing strategy is discussed. A review of modelling tools to support the

Printability of papers recycled from toner and inkjet-printed papers after deinking and recycling processes.

Science.gov (United States)

Karademir, Arif; Aydemir, Cem; Tutak, Dogan; Aravamuthan, Raja

2018-04-01

In our contemporary world, while part of the fibers used in the paper industry is obtained from primary fibers such as wood and agricultural plants, the rest is obtained from secondary fibers from waste papers. To manufacture paper with high optical quality from fibers of recycled waste papers, these papers require deinking and bleaching of fibers at desired levels. High efficiency in removal of ink from paper mass during recycling, and hence deinkability, are especially crucial for the optical and printability quality of the ultimate manufactured paper. In the present study, deinkability and printability performance of digitally printed paper with toner or inkjet ink were compared for the postrecycling product. To that end, opaque 80 g/m 2 office paper was digitally printed under standard printing conditions with laser toner or inkjet ink; then these sheets of paper were deinked by a deinking process based on the INGEDE method 11 p. After the deinking operation, the optical properties of the obtained recycled handsheets were compared with unprinted (reference) paper. Then the recycled paper was printed on once again under the same conditions as before with inkjet and laser printers, to monitor and measure printing color change before and after recycling, and differences in color universe. Recycling and printing performances of water-based inkjet and toner-based laser printed paper were obtained. The outcomes for laser-printed recycled paper were better than those for inkjet-printed recycled paper. Compared for luminosity Y, brightness, CIE a* and CIE b* values, paper recycled from laser-printed paper exhibited higher value than paper recycled from inkjet-printed paper.

Recycling of Glass

DEFF Research Database (Denmark)

Christensen, Thomas Højlund; Damgaard, Anders

2011-01-01

Glass is used for many purposes, but in the waste system glass is predominantly found in terms of beverage and food containers with a relatively short lifetime before ending up in the waste. Furthermore there is a large amount of flat glass used in building materials which also ends up in the waste...... system; this glass though has a long lifetime before ending up in the waste. Altogether these product types add up to 82% of the production of the European glass industry (IPCC, 2001). Recycling of glass in terms of cleaning and refilling of bottles as well as the use of broken glass in the production...... of new glass containers is well established in the glass industry. This chapter describes briefly howglass is produced and howwaste glass is recycled in the industry. Quality requirements and use of recycled products are discussed, as are the resource and environmental issues of glass recycling....

Environmental, economic, and energy impacts of material recovery facilities. A MITE Program evaluation

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

This report documents an evaluation of the environmental, economic, and energy impacts of material recovery facilities (MRFs) conducted under the Municipal Solid Waste Innovative Technology Evaluation (MITE) Program. The MITE Program is sponsored by the US Environmental Protection Agency to foster the demonstration and development of innovative technologies for the management of municipal solid waste (MSW). This project was also funded by the National Renewable Energy Laboratory (NREL). Material recovery facilities are increasingly being used as one option for managing a significant portion of municipal solid waste (MSW). The owners and operators of these facilities employ a combination of manual and mechanical techniques to separate and sort the recyclable fraction of MSW and to transport the separated materials to recycling facilities.

Disruptive Innovation in Chinese and Indian Businesses

DEFF Research Database (Denmark)

markets, has made these emerging economies fertile ground for developing and applying disruptive innovations. A novel mix of key attributes distinctive from those of established technologies or business models, disruptive innovations are typically inferior, yet affordable and "good-enough" products...... or services, which originate in lower-end market segments, but later move up to compete with those provided by incumbent firms. This book sheds new light on disruptive innovations both from and for the bottom of the pyramid in China and India, from the point of view of local entrepreneurs and international...... firms seeking to operate their businesses there. It covers both the theoretical and practical implications of disruptive innovation using conceptual frameworks alongside detailed case studies, whilst also providing a comparison of conditions and strategic options in India and China. Further, unlike...

You're a "What"? Recycling Coordinator

Science.gov (United States)

Torpey, Elka Maria

2011-01-01

Recycling coordinators supervise curbside and dropoff recycling programs for municipal governments or private firms. Today, recycling is mandatory in many communities. And advancements in collection and processing methods have helped to increase the quantity of materials for which the recycling coordinator is responsible. In some communities,…

Hydrogen Purification and Recycling for an Integrated Oxygen Recovery System Architecture

Science.gov (United States)

Abney, Morgan B.; Greenwood, Zachary; Wall, Terry; Miller, Lee; Wheeler, Ray

2016-01-01

The United States Atmosphere Revitalization life support system on the International Space Station (ISS) performs several services for the crew including oxygen generation, trace contaminant control, carbon dioxide (CO2) removal, and oxygen recovery. Oxygen recovery is performed using a Sabatier reactor developed by Hamilton Sundstrand, wherein CO2 is reduced with hydrogen in a catalytic reactor to produce methane and water. The water product is purified in the Water Purification Assembly and recycled to the Oxygen Generation Assembly (OGA) to provide O2 to the crew. This architecture results in a theoretical maximum oxygen recovery from CO2 of approximately 54% due to the loss of reactant hydrogen in Sabatier-produced methane that is currently vented outside of ISS. Plasma Methane Pyrolysis technology (PPA), developed by Umpqua Research Company, provides the capability to further close the Atmosphere Revitalization oxygen loop by recovering hydrogen from Sabatier-produced methane. A key aspect of this technology approach is to purify the hydrogen from the PPA product stream which includes acetylene, unreacted methane and byproduct water and carbon monoxide. In 2015, four sub-scale hydrogen separation systems were delivered to NASA for evaluation. These included two electrolysis single-cell hydrogen purification cell stacks developed by Sustainable Innovations, LLC, a sorbent-based hydrogen purification unit using microwave power for sorbent regeneration developed by Umpqua Research Company, and a LaNi4.6Sn0.4 metal hydride produced by Hydrogen Consultants, Inc. Here we report the results of these evaluations, discuss potential architecture options, and propose future work.

The nonlinear relationship between paper recycling and primary pulp requirements : modeling paper production and recycling in Europe

NARCIS (Netherlands)

Schenk, Niels J.; Moll, Henri C.; Potting, Josepha

Waste paper is suitable for recycling back into paper or for incineration for energy recovery. If waste paper is used for recycling, secondary pulp replaces virgin pulp. Fiber recycling is limited, however, because of physical constraints—particularly the breakage of fiber in the recycling

Improving the actinides recycling in closed fuel cycles, a major step towards nuclear energy sustainability

International Nuclear Information System (INIS)

Poinssot, C.; Grandjean, S.; Masson, M.; Bouillis, B.; Warin, D.

2013-01-01

Increasing the sustainability of nuclear energy is a longstanding road that requires a stepwise approach to successively tackle the following 3 objectives. First of all, optimize the consumption of natural resource to preserve them for future generations and hence guarantee the energetic independence of the countries (no uranium ore is needed anymore). The current twice-through cycle of Pu implemented by France, UK, Japan and soon China is a first step in this direction and already allows the development and optimization of the relevant industrial processes. It also allows a major improvement regarding the conditioning of the ultimate waste in a durable and robust nuclear glass. Secondly, the recycling of americium could be an interesting option for the future with the deployment of FR fleet to save the repository resource and optimize its use by allowing a denser disposal. It would limit the burden towards the future generations and the need for additional repositories before several centuries. Thirdly, the recycling of the whole minor actinides inventory could be an interesting option for the far-future for strongly decreasing the waste long-term toxicity, down to a few centuries. It would bring the waste issue back within the human history, which should promote its acceptance by the social opinion

The Three Rs: Reduce, Reuse, Recycle.

Science.gov (United States)

Science Activities, 1991

1991-01-01

A student hand-out for a recycling unit defines the terms reduce, recycle, and reuse as they relate to solid waste management. Presents the characteristics of recyclable items such as yard wastes, metals, glass, and paper. Lists organizations through which more information about recycling can be obtained. (MCO)

Replication of innovation in professional service firms: options for leveraging knowledge

NARCIS (Netherlands)

Tuominen, T.; van der Aa, W.

2013-01-01

In this conceptual paper we elaborate on the replication of innovation in professional service firms (PSFs). We do this by integrating literature streams on replication, knowledge sharing, productization of services and management of PSF’s. First we discuss the object of replication in order to

Reuse, Reduce, Recycle.

Science.gov (United States)

Briscoe, Georgia

1991-01-01

Discussion of recycling paper in law libraries is also applicable to other types of libraries. Results of surveys of law libraries that investigated recycling practices in 1987 and again in 1990 are reported, and suggestions for reducing the amount of paper used and reusing as much as possible are offered. (LRW)

What can recycling in thermal reactors accomplish?

International Nuclear Information System (INIS)

Piet, Steven J.; Matthern, Gretchen E.; Jacobson, Jacob J.

2007-01-01

Thermal recycle provides several potential benefits when used as stop-gap, mixed, or backup recycling to recycling in fast reactors. These three roles involve a mixture of thermal and fast recycling; fast reactors are required to some degree at some time. Stop-gap uses thermal reactors only until fast reactors are adequately deployed and until any thermal-recycle-only facilities have met their economic lifetime. Mixed uses thermal and fast reactors symbiotically for an extended period of time. Backup uses thermal reactors only if problems later develop in the fast reactor portion of a recycling system. Thermal recycle can also provide benefits when used as pure thermal recycling, with no intention to use fast reactors. However, long term, the pure thermal recycling approach is inadequate to meet several objectives. (authors)

What can Recycling in Thermal Reactors Accomplish?

International Nuclear Information System (INIS)

Steven Piet; Gretchen E. Matthern; Jacob J. Jacobson

2007-01-01

Thermal recycle provides several potential benefits when used as stop-gap, mixed, or backup recycling to recycling in fast reactors. These three roles involve a mixture of thermal and fast recycling; fast reactors are required to some degree at some time. Stop-gap uses thermal reactors only until fast reactors are adequately deployed and until any thermal-recycle-only facilities have met their economic lifetime. Mixed uses thermal and fast reactors symbiotically for an extended period of time. Backup uses thermal reactors only if problems later develop in the fast reactor portion of a recycling system. Thermal recycle can also provide benefits when used as pure thermal recycling, with no intention to use fast reactors. However, long term, the pure thermal recycling approach is inadequate to meet several objectives

Successfull example for a sustainable architectural culture. Facade consisting of recycled wood wraps the administration building; Gelungenes Beispiel fuer nachhaltige Baukultur. Fassade aus Recycling-Holz umhuellt Verwaltungsbau

Energy Technology Data Exchange (ETDEWEB)

Blauel, Christian [BDA Mecklenburg-Vorpommern, Schwerin (Germany)

2012-07-01

It has a role-model status for sustainable and ecologic construction - the new headquarters for the Agency for Renewable Ressources (Guelzow, Federal Republic of Germany). The building mainly consists of renewable resources. The Agency for Renewable Ressources as a project bearer of the Federal Ministry of Food, Agriculture and Consumer Protection (Berlin, Federal Republic of Germany) and the state of Mecklenburg-Western Pomerania as a client in the public works have implemented all that of innovation and efficient use of energy and resources, for which private developers now stand more likely. The highlight is a facade fully realized by recycled oak wood.

Implementing a campus wide recycling program

International Nuclear Information System (INIS)

Alvarez, L.

2002-01-01

'Full text:' The University of Windsor is currently expanding its recycling program to include all buildings on campus, but faces two challenges: 1) uncertainty about the current waste composition and distribution on campus; and 2) uncertainty about the effectiveness of increased recycling. This project assesses the current waste composition and the attitudes of the students towards recycling, and evaluates the effectiveness of proposed recycling activities. At present, paper is the only material that is collected throughout the entire campus. Except for two buildings, all other potentially recyclable materials within buildings, such as metal, glass, and plastic beverage containers, are discarded. The main focus of this research is on beverage containers as they represent clearly identifiable materials, but other materials were examined as well. To quantify the waste, different buildings on campus were classified according to their function: academic,operational and administrative. The waste composition study indicated that approximately 33% of the campus waste which is landfilled is composed of potentially recyclable material. A survey was then conducted to gauge the campus population's views on recycling issues that could affect the design of a recycling program. Interestingly, 97% of the respondents indicated a high willingness to recycle, but were uncertain as to how and where to recycle on campus. The project is currently assessing potential diversion rates using new, clearly identifiable recycling receptacles placed within selected classrooms for all major materials. There is a significant tradeoff however because the cost for new receptacles is considerable: multiple materials containers are often placed in high pedestrian traffic locations (e.g., hallways) and not always in classrooms,of which there are often many. This project will evaluate the basic benefits and costs of implementing a more comprehensive recycling program, and recommend how other

Thorium Fuel Options for Sustained Transuranic Burning in Pressurized Water Reactors - 12381

Energy Technology Data Exchange (ETDEWEB)

Rahman, Fariz Abdul; Lee, John C. [University of Michigan, Ann Arbor, MI (United States); Franceschini, Fausto; Wenner, Michael [Westinghouse Electric Company LLC, Cranberry Township, PA (United States)

2012-07-01

As described in companion papers, Westinghouse is proposing the adoption of a thorium-based fuel cycle to burn the transuranics (TRU) contained in the current Used Nuclear Fuel (UNF) and transition towards a less radio-toxic high level waste. A combination of both light water reactors (LWR) and fast reactors (FR) is envisaged for the task, with the emphasis initially posed on their TRU burning capability and eventually to their self-sufficiency. Given the many technical challenges and development times related to the deployment of TRU burners fast reactors, an interim solution making best use of the current resources to initiate burning the legacy TRU inventory while developing and testing some technologies of later use is desirable. In this perspective, a portion of the LWR fleet can be used to start burning the legacy TRUs using Th-based fuels compatible with the current plants and operational features. This analysis focuses on a typical 4-loop PWR, with 17x17 fuel assembly design and TRUs (or Pu) admixed with Th (similar to U-MOX fuel, but with Th instead of U). Global calculations of the core were represented with unit assembly simulations using the Linear Reactivity Model (LRM). Several assembly configurations have been developed to offer two options that can be attractive during the TRU transmutation campaign: maximization of the TRU transmutation rate and capability for TRU multi-recycling, to extend the option of TRU recycling in LWR until the FR is available. Homogeneous as well as heterogeneous assembly configurations have been developed with various recycling schemes (Pu recycle, TRU recycle, TRU and in-bred U recycle etc.). Oxide as well as nitride fuels have been examined. This enabled an assessment of the potential for burning and multi-recycling TRU in a Th-based fuel PWR to compare against other more typical alternatives (U-MOX and variations thereof). Results will be shown indicating that Th-based PWR fuel is a promising option to multi-recycle and

Lamps recycling aiming at the environment preservation

International Nuclear Information System (INIS)

Yamachita, Roberto Akira; Gama, Paulo Henrique R. Pereira; Haddad, Jamil; Santos, Afonso H. Moreira; Guardia, Eduardo C.

1999-01-01

The article discusses the following issues of lamps recycling in Brazil: mercury lamps recycling, recycling potential, energy conservation and environmental impacts, enterprises lamps recycling, and incentives policy

An industry response to recycle 2000

International Nuclear Information System (INIS)

Motl, G.P.; Loiselle, V.

1996-01-01

The US DOE is expected to issue a policy early this year articulating DOE's position on the recycle of DOE radioactive scrap metal. In anticipation of this 'Recycle 2000' initiative, the nuclear industry has formed a new trade association called the Association of Radioactive Metal Recyclers (ARMR). This article describes the Recycle 2000 initiative, provides some background on the ARMR and its membership, and identifies industry views on the actions to be taken and issues to be resolved in Recycle 2000 is to become a reality

Study of the radiosterilization dose effect on properties of poly(ethylene terephthalate) - PET recycled

International Nuclear Information System (INIS)

Isoldi, Ana Beatriz Godoy; Silva, Leonardo Gondim de Andrade e; Rosario, Salmo Cordeiro do

2002-01-01

The packing are in constant development, in function, especially, the process of globalization. The opening of the brazilian market after currency stabilization, caused technological innovations, change of habits and costumes of the population and environmental matters. Year after year, because of cost reductions, it became more extreme the hard study of the polymeric materials and their copolymers, their possible blends and their recycling, always seeking a better wrapping of the products, especially when it concerns to the food, increasing its shelf life. The process of sterilization of foods and modification of polymers through radiation are targets of growing interest by of the current industries linked to the nutrition and packing sectors. The objective of this paper is to discuss the application of the radiation (electron beam) in the sterilization of packings of recycled poly(ethylene terephthalate) PET, evaluating the possible effects on their properties. (author)

Recycling Behavior: A Multidimensional Approach

Science.gov (United States)

Meneses, Gonzalo Diaz; Palacio, Asuncion Beerli

2005-01-01

This work centers on the study of consumer recycling roles to examine the sociodemographic and psychographic profile of the distribution of recycling tasks and roles within the household. With this aim in mind, an empirical work was carried out, the results of which suggest that recycling behavior is multidimensional and comprises the undertaking…

Attributes to facilitate e-waste recycling behaviour

Directory of Open Access Journals (Sweden)

Senawi Nur Hidayah

2016-01-01

Full Text Available This study aims to identify the set of attributes to facilitate electronic waste (e-waste behaviour among the community. E-waste disposal is increasing from year to year in parallel with increasing of global population. The short lifespan of electronics and poor e-waste recycling behaviour is among the main contributors to the steadily increasing of e-waste generated. Current recycling rate among the nation is lacking behind, which is only 10.5%. A questionnaire survey has been conducted among the students in Universiti Teknologi Malaysia to evaluate the current e-waste recycling practice. The results showed that majority of the respondents did not recycle their e-waste on campus. Aggressive efforts is needed to realize the country’s target of 20% recycling rate in year 2020, one of the effective paths is to minimize e-waste generation via active e-waste recycling behaviour among the community. Extensive literatures have been reviewed to classify the attributes to facilitate effective e-waste recycling among the community. Total of five attributes that identified in this study which are Convenience of E- waste Recycling Infrastruture and Services, E-waste Recycling Information, Incentives For E-waste Recycling, Reminder to Recycle E-waste And E-waste Recycling Infrastructure and Services. The set of attributes identified in this study may serve as guideline for the management in designing program to foster e-waste recycling behaviour among the community.

Savannah River Site waste vitrification projects initiated throughout the United States: Disposal and recycle options

International Nuclear Information System (INIS)

Jantzen, C.M.

2000-01-01

A vitrification process was developed and successfully implemented by the US Department of Energy's (DOE) Savannah River Site (SRS) and at the West Valley Nuclear Services (WVNS) to convert high-level liquid nuclear wastes (HLLW) to a solid borosilicate glass for safe long term geologic disposal. Over the last decade, SRS has successfully completed two additional vitrification projects to safely dispose of mixed low level wastes (MLLW) (radioactive and hazardous) at the SRS and at the Oak Ridge Reservation (ORR). The SRS, in conjunction with other laboratories, has also demonstrated that vitrification can be used to dispose of a wide variety of MLLW and low-level wastes (LLW) at the SRS, at ORR, at the Los Alamos National Laboratory (LANL), at Rocky Flats (RF), at the Fernald Environmental Management Project (FEMP), and at the Hanford Waste Vitrification Project (HWVP). The SRS, in conjunction with the Electric Power Research Institute and the National Atomic Energy Commission of Argentina (CNEA), have demonstrated that vitrification can also be used to safely dispose of ion-exchange (IEX) resins and sludges from commercial nuclear reactors. In addition, the SRS has successfully demonstrated that numerous wastes declared hazardous by the US Environmental Protection Agency (EPA) can be vitrified, e.g. mining industry wastes, contaminated harbor sludges, asbestos containing material (ACM), Pb-paint on army tanks and bridges. Once these EPA hazardous wastes are vitrified, the waste glass is rendered non-hazardous allowing these materials to be recycled as glassphalt (glass impregnated asphalt for roads and runways), roofing shingles, glasscrete (glass used as aggregate in concrete), or other uses. Glass is also being used as a medium to transport SRS americium (Am) and curium (Cm) to the Oak Ridge Reservation (ORR) for recycle in the ORR medical source program and use in smoke detectors at an estimated value of $1.5 billion to the general public

Life Cycle Assessment and Optimization-Based Decision Analysis of Construction Waste Recycling for a LEED-Certified University Building

Directory of Open Access Journals (Sweden)

Murat Kucukvar

2016-01-01

Full Text Available The current waste management literature lacks a comprehensive LCA of the recycling of construction materials that considers both process and supply chain-related impacts as a whole. Furthermore, an optimization-based decision support framework has not been also addressed in any work, which provides a quantifiable understanding about the potential savings and implications associated with recycling of construction materials from a life cycle perspective. The aim of this research is to present a multi-criteria optimization model, which is developed to propose economically-sound and environmentally-benign construction waste management strategies for a LEED-certified university building. First, an economic input-output-based hybrid life cycle assessment model is built to quantify the total environmental impacts of various waste management options: recycling, conventional landfilling and incineration. After quantifying the net environmental pressures associated with these waste treatment alternatives, a compromise programming model is utilized to determine the optimal recycling strategy considering environmental and economic impacts, simultaneously. The analysis results show that recycling of ferrous and non-ferrous metals significantly contributed to reductions in the total carbon footprint of waste management. On the other hand, recycling of asphalt and concrete increased the overall carbon footprint due to high fuel consumption and emissions during the crushing process. Based on the multi-criteria optimization results, 100% recycling of ferrous and non-ferrous metals, cardboard, plastic and glass is suggested to maximize the environmental and economic savings, simultaneously. We believe that the results of this research will facilitate better decision making in treating construction and debris waste for LEED-certified green buildings by combining the results of environmental LCA with multi-objective optimization modeling.

Innovative process routes for a high-quality concrete recycling in the aggregates and cement industries

OpenAIRE

Bru , Kathy; Menard , Yannick; Touzé , Solène; Le Moign , Alain; Poirier , Jean Eric; Ruffié , Gilles; Bonnaudin , Fabrice; Von Der Weid , Frédéric

2011-01-01

International audience; Hardened concrete is a composite material that contains two main phases: the matrix (hardened cement paste, 20 %) and aggregates (gravels and sand, 80 %). The liberation and the recycling of these constituents can provide an answer to i) the exploration of new aggregates supply sources imposed by the depletion of natural deposit and the faced difficulties when trying to open new quarries and ii) the reduction of CO2 emissions in the clinker manufacturing process throug...

Recycling of used oil

International Nuclear Information System (INIS)

Vipulanandan, C.; Ghurye, G.

1992-01-01

This paper reports on used oil which is a valuable resource that should be recycled. Recycling used oil saves energy and natural resources. Used oil can be reprocessed and used as fuel in industrial burners and boilers. Unfortunately, more than 400 million gallons/year of used oil is lost through widespread dumping, partly due to lack of effective recycling procedures. Although used oil is not currently a federally listed hazardous waste, the U.S. EPA has proposed to list it as a hazardous waste, which will make recycling of used oil even more attractive. Laboratory samples, representing used oil, were used for detailed parametric studies and to determine the limitation of extending some of the current physical separation techniques such as sedimentation and centrifuging developed for oil-water and solid-liquid separation

Challenges in plastics recycling

DEFF Research Database (Denmark)

Pivnenko, Kostyantyn; Jakobsen, L. G.; Eriksen, Marie Kampmann

2015-01-01

Recycling of waste plastics still remains a challenging area in the waste management sector. The current and potential goals proposed on EU or regional levels are difficult to achieve, and even to partially fullfil them the improvements in collection and sorting should be considerable. A study...... was undertaken to investigate the factors affecting quality in plastics recycling. The preliminary results showed factors primarily influencing quality of plastics recycling to be polymer cross contamination, presence of additives, non-polymer impurities, and polymer degradation. Deprivation of plastics quality......, with respect to recycling, has been shown to happen throughout the plastics value chain, but steps where improvements may happen have been preliminary identified. Example of Cr in plastic samples analysed showed potential spreading and accumulation of chemicals ending up in the waste plastics. In order...

Studies on recycled aggregates-based concrete.

Science.gov (United States)

Rakshvir, Major; Barai, Sudhirkumar V

2006-06-01

Reduced extraction of raw materials, reduced transportation cost, improved profits, reduced environmental impact and fast-depleting reserves of conventional natural aggregates has necessitated the use of recycling, in order to be able to conserve conventional natural aggregate. In this study various physical and mechanical properties of recycled concrete aggregates were examined. Recycled concrete aggregates are different from natural aggregates and concrete made from them has specific properties. The percentages of recycled concrete aggregates were varied and it was observed that properties such as compressive strength showed a decrease of up to 10% as the percentage of recycled concrete aggregates increased. Water absorption of recycled aggregates was found to be greater than natural aggregates, and this needs to be compensated during mix design.

Management and recycling of electronic waste

International Nuclear Information System (INIS)

Tanskanen, Pia

2013-01-01

Waste electrical and electronic equipment (WEEE) is one of the largest growing waste streams globally. Hence, for a sustainable environment and the economic recovery of valuable material for reuse, the efficient recycling of electronic scrap has been rendered indispensable, and must still be regarded as a major challenge for today’s society. In contrast to the well-established recycling of metallic scrap, it is much more complicated to recycle electronics products which have reached the end of their life as they contain many different types of material types integrated into each other. As illustrated primarily for the recycling of mobile phones, the efficient recycling of WEEE is not only a challenge for the recycling industry; it is also often a question of as-yet insufficient collection infrastructures and poor collection efficiencies, and a considerable lack of the consumer’s awareness for the potential of recycling electronics for the benefit of the environment, as well as for savings in energy and raw materials

The Compressor Recycle System

OpenAIRE

Barstad, Bjørn Ove

2010-01-01

The compressor recycle system is the main focus of this thesis. When the mass flow through a compressor becomes too low, the compressor can plunge into surge. Surge is a term that is used for axisymmetric oscillation through a compressor and is highly unwanted. The recycle system feeds compressed gas back to the intake when the mass flow becomes too low, and thereby act as a safety system.A mathematical model of the recycle system is extended and simulated in SIMULINK. The mathematical model ...

Building Better Homes: Government Strategies for Promoting Innovation in Housing

National Research Council Canada - National Science Library

Hassell, Scott

2003-01-01

.... In this context, the report identifies options and strategies for the federal government to consider as it continues to further advance innovation in housing to make homes more affordable, durable...

MOX recycling-an industrial reality

International Nuclear Information System (INIS)

Shallo, G.D.F.

1996-01-01

Reprocessing and plutonium recycling have now attained industrial maturity in France and Europe. Specifically, mixed-oxide (MOX) fuel is fabricated and used in light water reactors (LWRs) in satisfactory operating conditions. The utilities and the fuel cycle industry experience no technical difficulties, and European recycling programs are growing steadily, from 18 reactors in operation today up to 50 expected around the year 2000, putting the system reprocessing-recycling in coherence: 25 t of plutonium will then be used each year to produce the electricity equivalence of 25 millions tons of oil. Plutonium recycling in MOX fuel in current LWRs proves to be technically safe and economically competitive and meets natural resource savings and environmental protection objectives. And recycling responds properly to the nonproliferation concerns. Such an industrial experience gives a unique reference for weapons plutonium disposition through MOX use in reactors

Renewable Energy Innovation Policy. Success Criteria and Strategies

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-03-15

Renewable energy technology (RET) innovation involves new, improved processes, as well as strategies to accelerate RET development, ranging from breakthroughs with basic technology inventions and improved research, development and deployment (RDD) systems, to improved market mechanisms and commercialisation. In order to achieve RET innovation, a country needs to put in place the right policy approaches, frameworks, governance and policy instruments. This working paper was compiled to assist countries with policy development in order to strengthen renewable energy innovation, primarily through a discussion of design criteria for innovation policy frameworks. The report identifies broad success criteria for innovation policy in the sector and suggests strategic policy approaches to advance RET innovation in the context of constrained options, competition for resources, and national economic development goals. For renewable energy innovation policy regimes to be succeed, they must satisfy two broad criteria: (a) promotion of sustained multi-stakeholder engagement around an achievable, shared vision; and (b) appropriate positioning of a country or region to anticipate and benefit from renewable energy technology flows.

Proceedings of the Symposium on Recycling of Metals arising from Operation and Decommissioning of Nuclear Facilities

International Nuclear Information System (INIS)

2014-04-01

The Symposium for the Recycling of Metals Arising from Operation and decommissioning of Nuclear Facilities was held in April 2014 at Studsvik's facility in Nykoeping, Sweden. The Symposium, hosted by Studsvik in conjunction with the Nuclear Energy Agency (NEA) of the Organisation for Economic Co-operation and Development (OECD) and the International Atomic Energy Agency (IAEA), covered a wide range of topics concerning current practice, experiences and innovations within the management of contaminated metallic radioactive material. The primary objective was to understand the differing approaches to clearance and recycling of materials from the nuclear industry across Europe in order to appreciate the issues faced from recovering resources once the material meets a country's clearance requirements. The outcome of the symposium has provided some interesting reflections for national and international bodies to consider when developing waste management guidance and policies. Over the three days of the symposium, presentations split into six topical sessions and posters regarding the recycling of contaminated metals were viewed by more than 150 people from 19 different countries. A series of group discussions were also held following each session to promote learning about current practices, highlight strategic issues related to metals recycling and develop professional networks across the industry. To stimulate discussion, a series of questions were posed at each group and the outcomes captured for inclusion within this report

ZZ WPPR, Pu Recycling Benchmark Results

International Nuclear Information System (INIS)

Lutz, D.; Mattes, M.; Delpech, Marc; Juanola, Marc

2002-01-01

Description of program or function: The NEA NSC Working Party on Physics of Plutonium Recycling has commissioned a series of benchmarks covering: - Plutonium recycling in pressurized-water reactors; - Void reactivity effect in pressurized-water reactors; - Fast Plutonium-burner reactors: beginning of life; - Plutonium recycling in fast reactors; - Multiple recycling in advanced pressurized-water reactors. The results have been published (see references). ZZ-WPPR-1-A/B contains graphs and tables relative to the PWR Mox pin cell benchmark, representing typical fuel for plutonium recycling, one corresponding to a first cycle, the second for a fifth cycle. These computer readable files contain the complete set of results, while the printed report contains only a subset. ZZ-WPPR-2-CYC1 are the results from cycle 1 of the multiple recycling benchmarks

Frequent Questions on Recycling

Science.gov (United States)

This is a list of frequent questions on recycling, broken down into five categories. These are answers to common questions that EPA has received from press and web inquiries. This list is located on the Reduce, Reuse, Recycle website.

Recycled concrete with coarse recycled aggregate. An overview and analysis

Directory of Open Access Journals (Sweden)

B. González-Fonteboa

2018-04-01

Full Text Available The construction field has contributed to environmental degradation, producing a high amount of construction and demolition waste (C&D waste and consuming large volumes of natural resources. In this context, recycled concrete (RC has been recognised as a means to preserve natural resources and reduce space for waste storage. During the last decades, many researchers have developed works studying different recycled concrete properties. This review focuses on structural RC made with coarse recycled aggregate from concrete waste. The main objective is to provide a state of the art report on RC’s properties and an analysis on how to predict them taking into account relevant research works. Moreover, the study tries to collect and update RC findings, proposing equations to define RC’s performance, in terms of mechanical strength, modulus of elasticity, stress-strain, creep and shrinkage.

Recycling of construction and demolition waste: case study in the Port of Antwerp

OpenAIRE

Bergmans, Jef; Broos, Kris; Nielsen, Peter; Dierckx, Philippe; Brijsse, Yvan; Jacobs, Kurt

2015-01-01

Construction and demolition waste (C&DW) represents one of the EU’s largest waste streams. According to the Directive 2008/98/EC on waste, at least 70 percent (by weight) of non-hazardous C&DW must be recuperated by 2020. Eurostat estimates an annual C&DW generation of 970 Mton in EU-27, representing an average value of almost 2.0 ton per inhabitant, with an average recovery rate of 47%. A case study in the Port of Antwerp (PoA) demonstrated new high grade recycling options for purified mater...

Solid waste recycling in Rajshahi city of Bangladesh.

Science.gov (United States)

Bari, Q Hamidul; Hassan, K Mahbub; Haque, M Ehsanul

2012-11-01

Efficient recycling of solid wastes is now a global concern for a sustainable and environmentally sound management. In this study, traditional recycling pattern of solid waste was investigated in Rajshahi municipality which is the fourth largest city of Bangladesh. A questionnaire survey had been carried out in various recycle shops during April 2010 to January 2011. There were 140 recycle shops and most of them were located in the vicinity of Stadium market in Rajshahi. About 1906 people were found to be involved in recycling activities of the city. The major fraction of recycled wastes were sent to capital city Dhaka for further manufacture of different new products. Only a small amount of wastes, specially plastics, were processed in local recycle factories to produce small washing pots and bottle caps. Everyday, an estimated 28.13 tons of recycled solid wastes were handled in Rajshahi city area. This recycled portion accounted for 8.25% of the daily total generated wastes (341 ton d(-1)), 54.6% of total recyclable wastes (51.49 ton d(-1)) and 68.29% of readily recyclable wastes (41.19 ton d(-1)). Major recycled materials were found to be iron, glass, plastic, and papers. Only five factories were involved in preliminary processing of recyclable wastes. Collecting and processing secondary materials, manufacturing recycled-content products, and then buying recycled products created a circle or loop that ensured the overall success of recycling and generated a host of financial, environmental, and social returns. Copyright © 2012 Elsevier Ltd. All rights reserved.

Toward an Innovation Policy for Pakistan

OpenAIRE

Speakman, John; Afzal, Kiran; Yuge, Yasuhiko; Hanna, James

2012-01-01

This policy paper aims to assist policy makers, as they develop the Pakistan Innovation Policy, with an independent assessment of where Pakistan stands now, an international perspective on policy priorities, a review of policy options and some implementation and institutional perspectives. The paper begins with a review of the key lessons of international experience together with a study of ...

Carambola optics for recycling of light.

Science.gov (United States)

Leutz, Ralf; Fu, Ling; Ries, Harald

2006-04-20

Recycling of light allows the luminance (radiance) emitted by a light source to be increased at the cost of reducing the total luminous flux (radiant power). Recycling of light means returning part of the emitted light to the source, where part of it will escape absorption. An optical design that is suitable for multiple and controlled recycling is described. Carambola optics is named for its resemblance to star fruit. Several pairs of mirrors or prisms redirect light repeatedly onto the source, thus achieving multiple transits of the light through the source. This recycled light exits the carambola in the same phase space as light directly emitted and not recycled.

Text recycling: acceptable or misconduct?

Science.gov (United States)

Harriman, Stephanie; Patel, Jigisha

2014-08-16

Text recycling, also referred to as self-plagiarism, is the reproduction of an author's own text from a previous publication in a new publication. Opinions on the acceptability of this practice vary, with some viewing it as acceptable and efficient, and others as misleading and unacceptable. In light of the lack of consensus, journal editors often have difficulty deciding how to act upon the discovery of text recycling. In response to these difficulties, we have created a set of guidelines for journal editors on how to deal with text recycling. In this editorial, we discuss some of the challenges of developing these guidelines, and how authors can avoid undisclosed text recycling.

Supply and demand of some critical metals and present status of their recycling in WEEE.

Science.gov (United States)

Zhang, Shengen; Ding, Yunji; Liu, Bo; Chang, Chein-Chi

2017-07-01

New development and technological innovations make electrical and electronic equipment (EEE) more functional by using an increasing number of metals, particularly the critical metals (e.g. rare and precious metals) with specialized properties. As millions of people in emerging economies adopt a modern lifestyle, the demand for critical metals is soaring. However, the increasing demand causes the crisis of their supply because of their simple deficiency in the Earth's crust or geopolitical constraints which might create political issues for their supply. This paper focuses on the sustainable supply of typical critical metals (indium, rare earth elements (REEs), lithium, cobalt and precious metals) through recycling waste electrical and electronic equipment (WEEE). To illuminate this issue, the production, consumption, expected future demand, current recycling situation of critical metals, WEEE management and their recycling have been reviewed. We find that the demand of indium, REEs, lithium and cobalt in EEE will continuously increasing, while precious metals are decreasing because of new substitutions with less or even without precious metals. Although the generation of WEEE in 2014 was about 41.9 million tons (Mt), just about 15% (6.5 Mt) was treated environmentally. The inefficient collection of WEEE is the main obstacle to relieving the supply risk of critical metals. Furthermore, due to the widespread use in low concentrations, such as indium, their recycling is not just technological problem, but economic feasibility is. Finally, relevant recommendations are point out to address these issues. Copyright © 2017 Elsevier Ltd. All rights reserved.

Structural recycled concrete: utilization of recycled aggregate from construction and demolition wastes

International Nuclear Information System (INIS)

Alaejos Gutierrez, P.; Sanchez de Juan, M.

2015-01-01

This paper aims to present the main results of CEDEX research works concerning the use of recycled aggregates for structural concretes. By way of conclusion, recommendations on the requirements of the recycled aggregates have been established, providing information about the influence of these aggregates on the properties of structural concrete. (Author)

Plastics recycling: challenges and opportunities.

Science.gov (United States)

Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

2009-07-27

Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3-4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

Plastics recycling: challenges and opportunities

Science.gov (United States)

Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

2009-01-01

Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3–4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

A comprehensive approach to solid waste and recycling at Sandia National Laboratories

International Nuclear Information System (INIS)

King, G.G.

1997-01-01

The abrupt closure of a nearby, and historically utilized, Kirtland Air Force Base landfill imposed a multitude of solid waste management problems for the Sandia National Laboratories/New Mexico (SNL) research and development facilities operated by Lockheed Martin Company. Due to the close proximity of KAFB, SNL historically used KAFB's landfill for disposal of solid waste. Under this arrangement SNL paid little or no cost for disposal of its solid waste stream. The disadvantage was that KAFB personnel did not track waste volumes entering the landfill from SNL. On August 1, 1994 this all came to an end. KAFB, without advance notice, closed the sanitary waste and asbestos cells of the landfill. The rapid resolution of unique regulatory issues; the aggressive accomplishment of reviewing options and implementing transport, screening, recycling and disposal procedures; and the construction and operation of a model, on-site Solid Waste Transfer Facility (SWTF) can serve as a case study for servicing DOE solid waste management and recycling needs in a safe, compliant, and timely manor

Recycling in the 90's - a shared responsibility

International Nuclear Information System (INIS)

Anon.

1993-01-01

Recycling means different things to different people. To consumers, recycling can mean putting out bottles and cans for curbside collection. To a product maker - a manufacturer of raw materials, fabricator of goods or products, or brand owner - recycling can mean reformulating goods to include recycled materials. To recycling service providers, recycling can mean providing cost-efficient collection services. To public policy makers in all levels of government recycling can mean establishing collection and utilization regulations. For recycling to work successfully, these diverse groups must work together and share responsibility for its success. Also, if recycling is to succeed on a large scale and over the long term, three critical points must be first addressed: These points are: approach, economics, and markets. These points are discussed

Innovation and risk-averse firms: Options on carbon allowances as a hedging tool

International Nuclear Information System (INIS)

Szolgayová, Jana; Golub, Alexander; Fuss, Sabine

2014-01-01

In a regulated world where government seeks to decarbonize the energy sector, firms face both indirect and direct costs of emitting CO 2 . This study seeks to take the perspective of the firm, which needs to maximize profits implying minimization of (carbon) cost as well. In this study, the firm can compose the cost-optimal portfolio of (a) investing into carbon-saving technology, which is currently expensive, (b) investing into carbon-saving technology R and D and adopt this technology at a later point, (c) buying allowances per ton of emitted CO 2 in a carbon market (alternatively this could be formulated as a tax), and (d) buying offsets traded in the same market, which are based on reduced emissions from deforestation and degradation (REDD+). Uncertainties in the cost of carbon coming from a lack of commitment in policy-making leading to fluctuations in markets and uncertainty in the payoff of R and D activities could provide disincentives to incur large up-front sunk cost and raise the economic value of being flexible. We apply a real options approach with stochastic carbon-saving technology costs and stochastic CO 2 costs. Assuming that firms are risk-averse, they will not only value flexibility, but also risk reductions from diversification over the different (carbon mitigation) options. - Highlights: • We study the compliance problem of a private firm under both regulatory and technological uncertainty in an optimal control setting. • When firms are risk-averse, forest-backed offset options will be part of the compliance portfolio. • R and D creates valuable options on new technology

Compressive strength improvement for recycled concrete aggregate

Directory of Open Access Journals (Sweden)

Mohammed Dhiyaa

2018-01-01

Full Text Available Increasing amount of construction waste and, concrete remnants, in particular pose a serious problem. Concrete waste exist in large amounts, do not decay and need long time for disintegration. Therefore, in this work old demolished concrete is crashed and recycled to produce recycled concrete aggregate which can be reused in new concrete production. The effect of using recycled aggregate on concrete compressive strength has been experimentally investigated; silica fume admixture also is used to improve recycled concrete aggregate compressive strength. The main parameters in this study are recycled aggregate and silica fume admixture. The percent of recycled aggregate ranged from (0-100 %. While the silica fume ranged from (0-10 %. The experimental results show that the average concrete compressive strength decreases from 30.85 MPa to 17.58 MPa when the recycled aggregate percentage increased from 0% to 100%. While, when silica fume is used the concrete compressive strength increase again to 29.2 MPa for samples with 100% of recycled aggregate.

Cost effectiveness of recycling: A systems model

Energy Technology Data Exchange (ETDEWEB)

Tonjes, David J., E-mail: david.tonjes@stonybrook.edu [Department of Technology and Society, College of Engineering and Applied Sciences, Stony Brook University, Stony Brook, NY 11794-3560 (United States); Waste Reduction and Management Institute, School of Marine and Atmospheric Sciences, Stony Brook University, Stony Brook, NY 11794-5000 (United States); Center for Bioenergy Research and Development, Advanced Energy Research and Technology Center, Stony Brook University, 1000 Innovation Rd., Stony Brook, NY 11794-6044 (United States); Mallikarjun, Sreekanth, E-mail: sreekanth.mallikarjun@stonybrook.edu [Department of Technology and Society, College of Engineering and Applied Sciences, Stony Brook University, Stony Brook, NY 11794-3560 (United States)

2013-11-15

Highlights: • Curbside collection of recyclables reduces overall system costs over a range of conditions. • When avoided costs for recyclables are large, even high collection costs are supported. • When avoided costs for recyclables are not great, there are reduced opportunities for savings. • For common waste compositions, maximizing curbside recyclables collection always saves money. - Abstract: Financial analytical models of waste management systems have often found that recycling costs exceed direct benefits, and in order to economically justify recycling activities, externalities such as household expenses or environmental impacts must be invoked. Certain more empirically based studies have also found that recycling is more expensive than disposal. Other work, both through models and surveys, have found differently. Here we present an empirical systems model, largely drawn from a suburban Long Island municipality. The model accounts for changes in distribution of effort as recycling tonnages displace disposal tonnages, and the seven different cases examined all show that curbside collection programs that manage up to between 31% and 37% of the waste stream should result in overall system savings. These savings accrue partially because of assumed cost differences in tip fees for recyclables and disposed wastes, and also because recycling can result in a more efficient, cost-effective collection program. These results imply that increases in recycling are justifiable due to cost-savings alone, not on more difficult to measure factors that may not impact program budgets.

Reusing recycled aggregates in structural concrete

Science.gov (United States)

Kou, Shicong

The utilization of recycled aggregates in concrete can minimize environmental impact and reduce the consumption of natural resources in concrete applications. The aim of this thesis is to provide a scientific basis for the possible use of recycled aggregates in structure concrete by conducting a comprehensive programme of laboratory study to gain a better understanding of the mechanical, microstructure and durability properties of concrete produced with recycled aggregates. The study also explored possible techniques to of improve the properties of recycled aggregate concrete that is produced with high percentages (≧ 50%) of recycled aggregates. These techniques included: (a) using lower water-to-cement ratios in the concrete mix design; (b) using fly ash as a cement replacement or as an additional mineral admixture in the concrete mixes, and (c) precasting recycled aggregate concrete with steam curing regimes. The characteristics of the recycled aggregates produced both from laboratory and a commercially operated pilot construction and demolition (C&D) waste recycling plant were first studied. A mix proportioning procedure was then established to produce six series of concrete mixtures using different percentages of recycled coarse aggregates with and without the use of fly ash. The water-to-cement (binder) ratios of 0.55, 0.50, 0.45 and 0.40 were used. The fresh properties (including slump and bleeding) of recycled aggregate concrete (RAC) were then quantified. The effects of fly ash on the fresh and hardened properties of RAC were then studied and compared with those RAC prepared with no fly ash addition. Furthermore, the effects of steam curing on the hardened properties of RAC were investigated. For micro-structural properties, the interfacial transition zones of the aggregates and the mortar/cement paste were analyzed by SEM and EDX-mapping. Moreover, a detailed set of results on the fracture properties for RAC were obtained. Based on the experimental

Quality Assessment of Mixed and Ceramic Recycled Aggregates from Construction and Demolition Wastes in the Concrete Manufacture According to the Spanish Standard.

Science.gov (United States)

Rodríguez-Robles, Desirée; García-González, Julia; Juan-Valdés, Andrés; Morán-Del Pozo, Julia Mª; Guerra-Romero, Manuel I

2014-08-13

Construction and demolition waste (CDW) constitutes an increasingly significant problem in society due to the volume generated, rendering sustainable management and disposal problematic. The aim of this study is to identify a possible reuse option in the concrete manufacturing for recycled aggregates with a significant ceramic content: mixed recycled aggregates (MixRA) and ceramic recycled aggregates (CerRA). In order to do so, several tests are conducted in accordance with the Spanish Code on Structural Concrete (EHE-08) to determine the composition in weight and physic-mechanical characteristics (particle size distributions, fine content, sand equivalent, density, water absorption, flakiness index, and resistance to fragmentation) of the samples for the partial inclusion of the recycled aggregates in concrete mixes. The results of these tests clearly support the hypothesis that this type of material may be suitable for such partial replacements if simple pretreatment is carried out. Furthermore, this measure of reuse is in line with European, national, and regional policies on sustainable development, and presents a solution to the environmental problem caused by the generation of CDW.

Quality Assessment of Mixed and Ceramic Recycled Aggregates from Construction and Demolition Wastes in the Concrete Manufacture According to the Spanish Standard

Directory of Open Access Journals (Sweden)

Desirée Rodríguez-Robles

2014-08-01

Full Text Available Construction and demolition waste (CDW constitutes an increasingly significant problem in society due to the volume generated, rendering sustainable management and disposal problematic. The aim of this study is to identify a possible reuse option in the concrete manufacturing for recycled aggregates with a significant ceramic content: mixed recycled aggregates (MixRA and ceramic recycled aggregates (CerRA. In order to do so, several tests are conducted in accordance with the Spanish Code on Structural Concrete (EHE-08 to determine the composition in weight and physic-mechanical characteristics (particle size distributions, fine content, sand equivalent, density, water absorption, flakiness index, and resistance to fragmentation of the samples for the partial inclusion of the recycled aggregates in concrete mixes. The results of these tests clearly support the hypothesis that this type of material may be suitable for such partial replacements if simple pretreatment is carried out. Furthermore, this measure of reuse is in line with European, national, and regional policies on sustainable development, and presents a solution to the environmental problem caused by the generation of CDW.

The Diffusion Effect of MSW Recycling

OpenAIRE

Yi-Tui Chen; Fu-Chiang Yang; Shih-Heng Yu

2017-01-01

The purpose of this paper is to compare the recycling performance for some waste fractions selected including food waste, bulk waste, paper, metal products, plastics/rubber and glass products and then to develop some directions for the future improvements. The priority of each waste fraction for recycling is also analyzed by using an importance-performance analysis. Traditionally, the recycling rate that is calculated by the ratio of waste recycled to waste collected is used as an indicator t...

Coolant clean-up and recycle systems

International Nuclear Information System (INIS)

Ito, Takao.

1979-01-01

Purpose: To increase the service life of mechanical seals in a shaft sealing device, eliminate leakages and improve the safety by providing a recycle pump for feeding coolants to a coolant clean-up device upon reactor shut-down and adapting the pump treat only low temperature and low pressure coolants. Constitution: The system is adapted to partially take out coolants from the pipeways of a recycling pump upon normal operation and feed them to a clean-up device. Upon reactor shut-down, the recycle pump is stopped and coolants are extracted by the recycle pump for shut-down into the clean-up device. Since the coolants are not fed to the clean-up device by the recycle pump during normal operation as conducted so far, high temperature and high pressure coolants are not directly fed to the recycle pump, thereby enabling to avoid mechanical problems in the pump. (Kamimura, M.)

Japan's fuel recycling policy

International Nuclear Information System (INIS)

Anon.

1991-01-01

The Atomic Energy Commission (AEC) has formulated Japanese nuclear fuel recycling plan for the next 20 years, based on the idea that the supply and demand of plutonium should be balanced mainly through the utilization of plutonium for LWRs. The plan was approved by AEC, and is to be incorporated in the 'Long term program for development and utilization of nuclear energy' up for revision next year. The report on 'Nuclear fuel recycling in Japan' by the committee is characterized by Japanese nuclear fuel recycling plan and the supply-demand situation for plutonium, the principle of the possession of plutonium not more than the demand in conformity with nuclear nonproliferation attitude, and the establishment of a domestic fabrication system of uranium-plutonium mixed oxide fuel. The total plutonium supply up to 2010 is estimated to be about 85 t, on the other hand, the demand will be 80-90 t. The treatment of plutonium is the key to the recycling and utilization of nuclear fuel. By around 2000, the private sector will commercialize the fabrication of the MOX fuel for LWRs at the annual rate of about 100 t. Commitment to nuclear nonproliferation, future nuclear fuel recycling program in Japan, MOX fuel fabrication system in Japan and so on are reported. (K.I.)

Design study of advanced nuclear fuel recycle system. Conceptual study of recycle system using molten salt

International Nuclear Information System (INIS)

Kakehi, I.; Shirai, N.; Hatano, M.; Kajitani, M.; Yonezawa, S.; Kawai, T.; Kawamura, F.; Tobe, K.; Takahashi, K.

1996-12-01

For the purpose of developing the future nuclear fuel recycle system, the design study of the advanced nuclear fuel recycle system is being conducted. This report describes intermediate accomplishments in the conceptual system study of the advanced nuclear fuel recycle system. Fundamental concepts of this system is the recycle system using molten salt which intend to break through the conventional concepts of purex and pellet fuel system. Contents of studies in this period are as follows, 1)feasibility study of the process by Cd-cathode for nitride fuel, 2)application study for the molten salt of low melting point (AlCl3+organic salt), 3)research for decladding (advantage of decladding by heat treatment), 4)behavior of FPs in electrorefining (behavior of iodine and volatile FP chlorides, FPs behavior in chlorination), 5)criticality analysis in electrorefiner, 6)drawing of off-gas flow diagram, 7)drawing of process machinery concept (cathode processor, vibration packing), 8)evaluation for the amounts of the high level radioactive wastes, 9)quality of the recycle fuels (FPs contamination of recycle fuel), 10)conceptual study of in-cell handling system, 11)meaning of the advanced nuclear fuel recycle system. The conceptual system study will be completed in describing concepts of the system and discussing issues for the developments. (author)

Influence of recycled aggregate quality and proportioning criteria on recycled concrete properties.

Science.gov (United States)

López-Gayarre, F; Serna, P; Domingo-Cabo, A; Serrano-López, M A; López-Colina, C

2009-12-01

This paper presents the results of experimental research using concrete produced by substituting part of the natural coarse aggregates with recycled aggregates from concrete demolition. The influence of the quality of the recycled aggregate (amount of declassified and source of aggregate), the percentage of replacement on the targeted quality of the concrete to be produced (strength and workability) has been evaluated. The granular structure of concrete and replacement criteria were analyzed in this study, factors which have not been analyzed in other studies. The following properties of recycled concretes were analyzed: density, absorption, compressive strength, elastic modulus, amount of occluded air, penetration of water under pressure and splitting tensile strength. A simplified test program was designed to control the costs of the testing while still producing sufficient data to develop reliable conclusions in order to make the number of tests viable whilst guaranteeing the reliability of the conclusions. Several factors were analyzed including the type of aggregate, the percentage of replacement, the type of sieve curve, the declassified content, the strength of concrete and workability of concrete and the replacement criteria. The type of aggregate and the percentage of replacement were the only factors that showed a clear influence on most of the properties. Compressive strength is clearly affected by the quality of recycled aggregates. If the water-cement ratio is kept constant and the loss of workability due to the effect of using recycled aggregate is compensated for with additives, the percentage of replacement of the recycled aggregate will not affect the compressive strength. The elastic modulus is affected by the percentage of replacement. If the percentage of replacement does not exceed 50%, the elastic modulus will only change slightly.

Strengthening Industrial Ecology’s Links with Business Studies: Insights and Potential Contributions from the Innovation and Business Models Literature

Directory of Open Access Journals (Sweden)

Samantha Sharpe

2014-03-01

Full Text Available The declining availability of natural resources and the environmental impacts of continued extraction of primary resources for production activities have forced greater focus on waste streams and recycling activities. Industrial ecology as a field of practice and theory has been closely related to sustainability issues, yet despite the development of much theory and specific tools and methodologies, the link between natural, industrial and economic systems is not convincing. Not only that, the need for delivering sustainable production and consumption practices is increasing, which is demanding new solutions to existing problems, particularly around the degree of novelty. The interaction of industrial ecology with business studies and industrial investment decision-making remains under-developed, and this is likely impacting on the adoption of more sustainable and resource-efficient practices. As such, this paper uses a constructive approach and explores how two areas of the literature can support the development of the industrial ecology field into strategic business practice: firstly, the innovation literature, particularly the emerging work on open innovation and sustainable innovation as a model to understand radical innovation processes and the creation and maintenance of networked systems of firms; secondly, the closely related area of business model (BM innovation, specifically the emerging typologies of sustainable BMs and how these typologies can be developed and used as a route to positioning recycling activities at the strategic management level of the firm.

Proceedings of the waste recycling workshop

Energy Technology Data Exchange (ETDEWEB)

Bailey, R.E.; Thomas, A.F.; Ries, M.A. [eds.] [Ohio State Univ., Columbus, OH (United States)

1993-12-31

Recorded are seventeen talks from five sessions at the workshop. FERMCO`s recycling program, state of the art recycling technology, and an integrated demonstration of deactivation, decommissioning and decommissioning are presented in the plenary session. In the concrete session, decontamination and recycling are discussed. In the transite session, regulations are considered along with recycling and decontamination. In the metals session, radioactive scrap metals are emphasized. And in the regulatory considerations and liabilities session, DOE and EPA viewpoints are discussed. (GHH)

MOX fuel reprocessing and recycling

International Nuclear Information System (INIS)

Guillet, J.L.

1990-01-01

This paper is devoted to the reprocessing of MOX fuel in UP2-800 plant at La Hague, and to the MOX successive reprocessing and recycling. 1. MOX fuel reprocessing. In a first step, the necessary modifications in UP2-800 to reprocess MOX fuel are set out. Early in the UP2-800 project, actions have been taken to reprocess MOX fuel without penalty. They consist in measures regarding: Dissolution; Radiological shieldings; Nuclear instrumentation; Criticality. 2. Mox successive reprocessing and recycling. The plutonium recycling in the LWR is now a reality and, as said before, the MOX fuel reprocessing is possible in UP2-800 plant at La Hague. The following actions in this field consist in verifying the MOX successive reprocessing and recycling possibilities. After irradiation, the fissile plutonium content of irradiated MOX fuel is decreased and, in this case, the re-use of plutonium in the LWR need an important increase of initial Pu enrichment inconsistent with the Safety reactor constraints. Cogema opted for reprocessing irradiated MOX fuel in dilution with the standard UO2 fuel in appropriate proportions (1 MOX for 4 UO2 fuel for instance) in order to save a fissile plutonium content compatible with MOX successive recycling (at least 3 recyclings) in LWR. (author). 2 figs

40 CFR 141.76 - Recycle provisions.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Recycle provisions. 141.76 Section 141...) NATIONAL PRIMARY DRINKING WATER REGULATIONS Filtration and Disinfection § 141.76 Recycle provisions. (a... recycle spent filter backwash water, thickener supernatant, or liquids from dewatering processes must meet...

Challenges of metal recycling and an international covenant as possible instrument of a globally extended producer responsibility.

Science.gov (United States)

Wilts, Hennning; Bringezu, Stefan; Bleischwitz, Raimund; Lucas, Rainer; Wittmer, Dominic

2011-09-01

As illustrated by the case studies of end-of-life vehicles and waste electric and electronic equipment, the approach of an extended producer responsibility is undermined by the exports of used and waste products. This fact causes severe deficits regarding circular flows, especially of critical raw materials such as platinum group metals. With regard to global recycling there seems to be a responsibility gap which leads somehow to open ends of waste flows and a loss or down-cycling of potential secondary resources. Existing product-orientated extended producer responsibility (EPR) approaches with mass-based recycling quotas do not create adequate incentives to supply waste materials containing precious metals to a high-quality recycling and should be amended by aspects of a material stewardship. The paper analyses incentive effects on EPR for the mentioned product groups and metals, resulting from existing regulations in Germany. It develops a proposal for an international covenant on metal recycling as a policy instrument for a governance-oriented framework to initiate systemic innovations along the complete value chain taking into account product group- and resource group-specific aspects on different spatial levels. It aims at the effective implementation of a central idea of EPR, the transition of a waste regime still focusing on safe disposal towards a sustainable management of resources for the complete lifecycle of products.

Safety characteristics of options for plasma-facing components for ITER and beyond

International Nuclear Information System (INIS)

Piet, S.J.; McCarthy, K.A.; Holland, D.F.; Longhurst, G.R.; Merrill, B.J.

1991-01-01

Plasma-facing components (PFC) likely dominate the safety hazards of the International Thermonuclear Experimental Reactor (ITER) and post-ITER machines. To gain regulatory approval and for fusion energy to fulfill its ultimate attractive safety and environmental potential, safety must be considered when selecting among PFC options. This paper summarizes current PFC safety information. PFC safety issues fall into seven areas: disruption tolerance, disruption severity, tritium inventory and permeation, accidental energy release, activation/toxin hazards, cooling disturbances, and system issues. RFC options include current ITER mainline options (Be or W coating, C tiles), variants on current ITER options, and liquid metal (LM) divertors. No PFC option that we have examined is free of critical safety concerns. There are also innovative ideas that may improve any PFC's performance -- super-permeable vacuum ducts, helium self-pumping, and gaseous divertors. We conclude with recommendations and a future strategy. 17 refs., 1 fig., 3 tabs

Restaurant challenge offers healthful meal options and builds diabetes awareness.

Science.gov (United States)

Blair, Angela M; Drass, Janice A; Stone, Marylou; Rhoades, Deborah; Baldwin, Susan A; Russ, Kelsey M

2011-01-01

The Frederick Restaurant Challenge is an innovative project based on a collaborative effort among community organizations and partners designed to offer delicious healthful meal options at local restaurants during the month of November for American Diabetes Month. Local restaurants were challenged to participate and submitted recipes for healthful meals to the Frederick County Diabetes Coalition for review by registered dietitians. Diners voted on meals to determine the challenge winner(s), and were eligible to win prizes as well. Publicity prior to and during the month was effective in creating positive news about healthful meals when eating out, raised awareness about diabetes, and provided restaurants with desirable advertising opportunities. Feedback from restaurants and diners was overwhelmingly positive. The purpose of this article is to describe this successful low-budget project to encourage its replication in local communities. The Frederick Restaurant Challenge proved to be a very successful, innovative, low-budget project that met its intended goals: to develop healthful meal options for people with diabetes (or for anyone wishing to eat healthier); to demonstrate that healthful food can taste delicious; and to encourage restaurants to continue offering healthful options on their menus beyond the challenge month. Community interventions such as the Frederick Restaurant Challenge offer unique and important strategies for affecting change and raising awareness not only for people with diabetes but also for the entire community.

Densifying the city: urban recycle as a strategic system to refurbish the built environment

Directory of Open Access Journals (Sweden)

Vittorino Belpoliti

2015-11-01

Full Text Available The persisting economic crisis and the necessity for more sustainable construction processes imply the need for innovative strategies to reuse the existing building stock. Retrofit and recycling plans are already active for whole city districts, adopting the urban densification strategy to reduce the consumption of resources, promoting the functional, technological, and energy refurbishment of the existing city districts The study introduces considerations and tools to increase the efficiency of retrofit action onto abandoned and degraded area through the improvement of their energy and environmental performances. 

Auditing Operating Room Recycling: A Management Case Report.

Science.gov (United States)

McGain, Forbes; Jarosz, Katherine Maria; Nguyen, Martin Ngoc Hoai Huong; Bates, Samantha; O'Shea, Catherine Jane

2015-08-01

Much waste arises from operating rooms (ORs). We estimated the practical and financial feasibility of an OR recycling program, weighing all waste from 6 ORs in Melbourne, Australia. Over 1 week, 237 operations produced 1265 kg in total: general waste 570 kg (45%), infectious waste 410 kg (32%), and recyclables 285 kg (23%). The achieved recycling had no infectious contamination. The achieved recycling/potential recycling rate was 285 kg/517 kg (55%). The average waste disposal costs were similar for general waste and recycling. OR recycling rates of 20%-25% total waste were achievable without compromising infection control or financial constraints.

How Does the Innovation System in the Spanish Ceramic Tile Sector Function?

International Nuclear Information System (INIS)

Gabaldon-Estevan, D.; Hekkert, M. P.

2013-01-01

In this article we apply the functions of innovation systems framework to assess its appropriateness to characterise the innovation activity of the tile industry in Castellon. This framework is based on idea that a well functioning innovation system requires that a number of key activities take place. If this occurs innovative output is higher. Our analysis provides a deeper understanding of the role of innovation as a strategic option in a mature industry in the context of globalisation. By applying this new theoretical approach to study innovation and highlighting the functions that the system requires, we shown the constraints, inertias, challenges and opportunities that the innovation system of the tile industry in Castellon faces. The results also show that the functional approach allows higher flexibility in order to recognise and analyse the opportunities and constraints that a given innovation system presents. (Author)

Electric vehicle recycling 2020: Key component power electronics.

Science.gov (United States)

Bulach, Winfried; Schüler, Doris; Sellin, Guido; Elwert, Tobias; Schmid, Dieter; Goldmann, Daniel; Buchert, Matthias; Kammer, Ulrich

2018-04-01

Electromobility will play a key role in order to reach the specified ambitious greenhouse gas reduction targets in the German transport sector of 42% between 1990 and 2030. Subsequently, a significant rise in the sale of electric vehicles (EVs) is to be anticipated in future. The amount of EVs to be recycled will rise correspondingly after a delay. This includes the recyclable power electronics modules which are incorporated in every EV as an important component for energy management. Current recycling methods using car shredders and subsequent post shredder technologies show high recycling rates for the bulk metals but are still associated with high losses of precious and strategic metals such as gold, silver, platinum, palladium and tantalum. For this reason, the project 'Electric vehicle recycling 2020 - key component power electronics' developed an optimised recycling route for recycling power electronics modules from EVs which is also practicable in series production and can be implemented using standardised technology. This 'WEEE recycling route' involves the disassembly of the power electronics from the vehicle and a subsequent recycling in an electronic end-of-life equipment recycling plant. The developed recycling process is economical under the current conditions and raw material prices, even though it involves considerably higher costs than recycling using the car shredder. The life cycle assessment shows basically good results, both for the traditional car shredder route and the developed WEEE recycling route: the latter provides additional benefits from some higher recovery rates and corresponding credits.

Feedwater recycling system in BWR type reactor

International Nuclear Information System (INIS)

Shimamoto, Yoshiharu.

1980-01-01

Purpose: To improve the reactor safety by preventing thermal stresses and cracks generated in structural materials due to the fluctuations in the temperature for high temperature water - low temperature water mixture near the feedwater nozzle. Method: Feedwater pipes are connected to a pressure vessel not directly but by way of a flow control valve. While the recycled water is circulated from an inlet nozzle to an outlet nozzle through a recycle pump, flow control valve and recycling pipeways, feedwater is fed from the feedwater pipes to the recycling pipeways by way of the flow control valve. More specifically, since the high temperature recycle water and the low temperature recycle water are mixed within the pipeways, the temperature fluctuations resulted from the temperature difference between the recycle water and the feedwater is reduced to prevent thermal fatigue and generation of cracks thereby securing the reactor safety. (Furukawa, Y.)

Quality Assessment of Mixed and Ceramic Recycled Aggregates from Construction and Demolition Wastes in the Concrete Manufacture According to the Spanish Standard †

Science.gov (United States)

Rodríguez-Robles, Desirée; García-González, Julia; Juan-Valdés, Andrés; Pozo, Julia Mª Morán-del; Guerra-Romero, Manuel I

2014-01-01

Construction and demolition waste (CDW) constitutes an increasingly significant problem in society due to the volume generated, rendering sustainable management and disposal problematic. The aim of this study is to identify a possible reuse option in the concrete manufacturing for recycled aggregates with a significant ceramic content: mixed recycled aggregates (MixRA) and ceramic recycled aggregates (CerRA). In order to do so, several tests are conducted in accordance with the Spanish Code on Structural Concrete (EHE-08) to determine the composition in weight and physic-mechanical characteristics (particle size distributions, fine content, sand equivalent, density, water absorption, flakiness index, and resistance to fragmentation) of the samples for the partial inclusion of the recycled aggregates in concrete mixes. The results of these tests clearly support the hypothesis that this type of material may be suitable for such partial replacements if simple pretreatment is carried out. Furthermore, this measure of reuse is in line with European, national, and regional policies on sustainable development, and presents a solution to the environmental problem caused by the generation of CDW. PMID:28788164

Recycling of reprocessed uranium

International Nuclear Information System (INIS)

Randl, R.P.

1987-01-01

Since nuclear power was first exploited in the Federal Republic of Germany, the philosophy underlying the strategy of the nuclear fuel cycle has been to make optimum use of the resource potential of recovered uranium and plutonium within a closed fuel cycle. Apart from the weighty argument of reprocessing being an important step in the treatment and disposal of radioactive wastes, permitting their optimum ecological conditioning after the reprocessing step and subsequent storage underground, another argument that, no doubt, carried weight was the possibility of reducing the demand of power plants for natural uranium. In recent years, strategies of recycling have emerged for reprocessed uranium. If that energy potential, too, is to be exploited by thermal recycling, it is appropriate to choose a slightly different method of recycling from the one for plutonium. While the first generation of reprocessed uranium fuel recycled in the reactor cuts down natural uranium requirement by some 15%, the recycling of a second generation of reprocessed, once more enriched uranium fuel helps only to save a further three per cent of natural uranium. Uranium of the second generation already carries uranium-232 isotope, causing production disturbances, and uranium-236 isotope, causing disturbances of the neutron balance in the reactor, in such amounts as to make further fabrication of uranium fuel elements inexpedient, even after mixing with natural uranium feed. (orig./UA) [de

Characterization of quality recycled gypsum and plasterboard with maximized recycled content

International Nuclear Information System (INIS)

Jiménez-Rivero, J.; García-Navarro, J.

2017-01-01

The quality of secondary materials is imperative to promote a circular economy. In order to improve the way in which the quality of recycled gypsum is assessed, European guidelines on recycled gypsum (RG) quality criteria have been outlined in the framework of the Life+ Gypsum to Gypsum (GtoG) project. Such GtoG guidelines, along with the European Standard on gypsum plasterboard EN 520, provided the basis for this study. During the GtoG project, gypsum recycling and plasterboard manufacturing processes were monitored by testing the gypsum feedstock and the plasterboard produced. The aim of this paper is to discuss the results obtained on relevant parameters that characterize gypsum as a secondary raw material, as well as the resulting product. The minimum requirements were fulfilled by 56% of the RG samples and 86% of the plasterboard with increased RG. [es

Synthesis and chemical recycling of high polymers using C1 compounds; C1 kagobutsu ni yoru kobunshi no chemical recycle

Energy Technology Data Exchange (ETDEWEB)

Masuda, T. [National Institute of Materials and Chemical Research, Tsukuba (Japan)

1997-09-01

The paper outlined a study of the synthesis of high polymers using C1 compounds which are continuously usable chemical materials and the related compounds such as the derivatives, and also the chemical recycle. In the case of waste plastics mixed in urban refuse, effective is the chemical recycle where C1 compounds obtained by gasifying the mixed waste are used as high polymer material. For the synthesis and recycle of high polymers using C1 compounds, there are three routes: Route A (recycle via high polymer materials), Route B (recycle via C1 compounds and high polymer materials), and Route C including global-scale carbon recycle (recycle via carbon dioxide from biodegradable plastics using microorganism). Among high polymers, those that can be synthesized from C1 compounds, for example, polymethylene, polyacetal and polyketone can be chemically recycled by Route B. 30 refs., 2 figs., 1 tab.

A UK perspective on recycling

International Nuclear Information System (INIS)

Williams, T.

1991-01-01

The United Kingdom, through the recycling of depleted uranium from Magnox reactors into Advanced Gas-cooled Reactor (AGR) fuel, has already recycled significant quantities of reprocessed material in reactors owned by Nuclear Electric plc and Scottish Nuclear Limited. This AGR fuel has been satisfactorily irradiated and discharged over a decade or more, and will be reprocessed in the new Thermal Oxide Reprocessing Plant (THORP), currently under construction in the UK. British Nuclear Fuels plc (BNFL) and the UK Atomic Energy Authority (UKAEA) have also been exploiting the potential of plutonium recycled in mixed oxide (MOX) fuel, which they have been making since 1963. All of the UK nuclear companies are committed to further recycling of Magnox depleted uranium during the 1990s, and it is anticipated that oxide recycling will also become firmly established during the next decade. British Nuclear Fuels and Urenco Ltd, as the providers of fuel cycle services, are developing an infrastructure to close the fuel cycle for oxide nuclear fuel, using both the uranium and plutonium arising from reprocessing. (author)

Prioritising health service innovation investments using public preferences: a discrete choice experiment.

Science.gov (United States)

Erdem, Seda; Thompson, Carl

2014-08-28

Prioritising scarce resources for investment in innovation by publically funded health systems is unavoidable. Many healthcare systems wish to foster transparency and accountability in the decisions they make by incorporating the public in decision-making processes. This paper presents a unique conceptual approach exploring the public's preferences for health service innovations by viewing healthcare innovations as 'bundles' of characteristics. This decompositional approach allows policy-makers to compare numerous competing health service innovations without repeatedly administering surveys for specific innovation choices. A Discrete Choice Experiment (DCE) was used to elicit preferences. Individuals chose from presented innovation options that they believe the UK National Health Service (NHS) should invest the most in. Innovations differed according to: (i) target population; (ii) target age; (iii) implementation time; (iv) uncertainty associated with their likely effects; (v) potential health benefits; and, (vi) cost to a taxpayer. This approach fosters multidimensional decision-making, rather than imposing a single decision criterion (e.g., cost, target age) in prioritisation. Choice data was then analysed using scale-adjusted Latent Class models to investigate variability in preferences and scale and valuations amongst respondents. Three latent classes with considerable heterogeneity in the preferences were present. Each latent class is composed of two consumer subgroups varying in the level of certainty in their choices. All groups preferred scientifically proven innovations, those with potential health benefits that cost less. There were, however, some important differences in their preferences for innovation investment choices: Class-1 (54%) prefers innovations benefitting adults and young people and does not prefer innovations targeting people with 'drug addiction' and 'obesity'. Class- 2 (34%) prefers innovations targeting 'cancer' patients only and has

Recycling Pressure-Sensitive Products

Science.gov (United States)

Jihui Guo; Larry Gwin; Carl Houtman; Mark Kroll; Steven J. Severtson

2012-01-01

The efficient control of contaminants such as metals, plastics, inks and adhesives during the processing of recovered paper products determines the profitability of recycling mills. In fact, it is arguably the most important technical obstacle in expanding the use of recycled paper.1-4 An especially challenging category of contaminants to manage...

DWPF Recycle Evaporator Simulant Tests

International Nuclear Information System (INIS)

Stone, M

2005-01-01

Testing was performed to determine the feasibility and processing characteristics of an evaporation process to reduce the volume of the recycle stream from the Defense Waste Processing Facility (DWPF). The concentrated recycle would be returned to DWPF while the overhead condensate would be transferred to the Effluent Treatment Plant. Various blends of evaporator feed were tested using simulants developed from characterization of actual recycle streams from DWPF and input from DWPF-Engineering. The simulated feed was evaporated in laboratory scale apparatus to target a 30X volume reduction. Condensate and concentrate samples from each run were analyzed and the process characteristics (foaming, scaling, etc) were visually monitored during each run. The following conclusions were made from the testing: Concentration of the ''typical'' recycle stream in DWPF by 30X was feasible. The addition of DWTT recycle streams to the typical recycle stream raises the solids content of the evaporator feed considerably and lowers the amount of concentration that can be achieved. Foaming was noted during all evaporation tests and must be addressed prior to operation of the full-scale evaporator. Tests were conducted that identified Dow Corning 2210 as an antifoam candidate that warrants further evaluation. The condensate has the potential to exceed the ETP WAC for mercury, silicon, and TOC. Controlling the amount of equipment decontamination recycle in the evaporator blend would help meet the TOC limits. The evaporator condensate will be saturated with mercury and elemental mercury will collect in the evaporator condensate collection vessel. No scaling on heating surfaces was noted during the tests, but splatter onto the walls of the evaporation vessels led to a buildup of solids. These solids were difficult to remove with 2M nitric acid. Precipitation of solids was not noted during the testing. Some of the aluminum present in the recycle streams was converted from gibbsite to

Encouraging Vietnamese Household Recycling Behavior: Insights and Implications

Directory of Open Access Journals (Sweden)

The Ninh Nguyen

2017-01-01

Full Text Available This research aims to provide new insights into various determinants affecting household recycling. By focusing on Vietnam, this research also extends knowledge about sustainable behavior in emerging markets, which are the major culprits in terms of greenhouse gas emissions. Hypotheses were developed as a result of the critical review of relevant studies in the fields of marketing, psychology, and economics, and then tested using a quantitative survey data. Structured questionnaires were administered to Vietnamese respondents which yielded 486 usable responses. Multivariate statistics reveal that all the determinants influenced their recycling behavior except for moral norms. Attitude towards the importance of recycling exerted the strongest influence, followed by subjective norms and warm glow respectively. On the other hand, attitude towards the inconvenience of recycling significantly reduced recycling behavior. The research findings have important implications for strategies aimed at promoting recycling behavior. Communication and education programs should emphasize how household recycling contributes to environmental protection, as well as stress intrinsic rewards when recycling. Public media campaigns should feature opinion leaders and attractive communicators, who can effectively apply social pressure to perform recycling behavior. Organizations should also make every effort to make recycling more convenient.

Declassification, an actual operating materials management option in Cofrentes

International Nuclear Information System (INIS)

Garcia-Bermejo, R.; Diego compadre, J. L. de; Lopez Alvarez, L.; Analya Lazaro, M.

2014-01-01

Methods and procedures developed for declassification feature a series of methodological options and innovative technology, including the systematic use of the spatial random variable named index of Residual activity, level specific factors for declassification determined empirically for each unit of characterization and contrasts of hypothesis not parametric which are used in the demonstration of compliance of the levels of declassification Decision rules authorized by the CSN. (Author)

Antimony recycling in the United States in 2000

Science.gov (United States)

Carlin, James F.

2006-01-01

The importance of recycling has become more obvious as concerns about the environment and import dependence have grown in recent years. When materials are recycled, fewer natural resources are consumed, and less waste products go to landfills or pollute the water and air. This study, one of a series of reports on metals recycling in 2000, discusses the flow of antimony from mining through its uses and disposal with emphasis on recycling. In 2000, the recycling efficiency for antimony was estimated to be 89 percent, and the recycling rate was about 20 percent.

Life cycle assessment of post-consumer plastics production from waste electrical and electronic equipment (WEEE) treatment residues in a Central European plastics recycling plant.

Science.gov (United States)

Wäger, Patrick A; Hischier, Roland

2015-10-01

Plastics play an increasingly important role in reaching the recovery and recycling rates defined in the European WEEE Directive. In a recent study we have determined the life cycle environmental impacts of post-consumer plastics production from mixed, plastics-rich WEEE treatment residues in the Central European plant of a market-leading plastics recycler, both from the perspective of the customers delivering the residues and the customers buying the obtained post-consumer recycled plastics. The results of our life cycle assessments, which were extensively tested with sensitivity analyses, show that from both perspectives plastics recycling is clearly superior to the alternatives considered in this study (i.e. municipal solid waste incineration (MSWI) and virgin plastics production). For the three ReCiPe endpoint damage categories, incineration in an MSWI plant results in an impact exceeding that of the examined plastics recycling facility each by about a factor of 4, and the production of virgin plastics has an impact exceeding that of the post-consumer recycled (PCR) plastics production each by a factor of 6-10. On a midpoint indicator level the picture is more differentiated, showing that the environmental impacts of the recycling options are lower by 50% and more for almost all impact factors. While this provides the necessary evidence for the environmental benefits of plastics recycling compared to existing alternatives, it can, however, not be taken as conclusive evidence. To be conclusive, future research will have to address the fate of hazardous substances in the outputs of such recycling systems in more detail. Copyright © 2015 Elsevier B.V. All rights reserved.

Case study of recycling options for New Hampshire generators

Energy Technology Data Exchange (ETDEWEB)

Coleman, P.M. [Resource Conservation Services, Inc., Brunswick, ME (United States)

1993-12-31

The successful development of utilization programs for ash generated by the combustion of biomass in Northern New England is described, with special focus on the State of New Hampshire. With the development of over 25 large scale biomass boilers in Northern New England during the past ten years, has come the need to dispose of the over 300,000 cubic yards of ash produced as a combustion by-product. Resource Conservation Services, Inc., a private company, pioneered the development of various utilization options for biomass boiler ash. The major use of ash has been as an agricultural soil amendment. The high levels of calcium in wood ash make it valuable as a lime substitute for raising soil pH. Wood ash also contains significant levels of potassium, phosphorus and magnesium as well as lesser amounts of other plant nutrients which make it valuable as a fertilizer. Soil testing is used to determine application rates to agricultural land. Ash use is regulated by State environmental protection agencies. Heavy metal content of wood ash meets regulatory standards. Wood ash also proven valuable as a bulking and odor control material when mixed with municipal wastewater treatment plant sludge and composted. The high pH of wood ash controls odor producing compounds generated by the composting process. High carbon ash also controls odors through improved aeration and by adsorption of odor producing compounds by the {open_quotes}char{close_quotes} in the ash. Additional uses for wood ash are as a component of concrete products such as {open_quotes}flowable fill{close_quotes} and {open_quotes}soil cement,{close_quotes} as a lime substitute for sludge stabilization, and as landfill daily cover. As higher value uses for wood ash have been developed, ash disposal costs have been reduced and ash is viewed more like a commodity than a waste material.

An approach for assessing development and deployment risks in the DOE fuel cycle options evaluation and screening study - 5267

International Nuclear Information System (INIS)

Gehin, J.C.; Worrall, A.; Oakley, B.; Jenni, K.; Taiwo, T.; Wigeland, R.

2015-01-01

One of the key objectives of the U.S. Department of Energy (DOE) Nuclear Energy Research/development road-map is the development of sustainable nuclear fuel cycles that can improve natural resource utilization and provide solutions to the management of nuclear wastes. Recently, an evaluation and screening (ES) of fuel cycle systems has been conducted to identify those options that provide the best opportunities for obtaining such improvements and also to identify the required research and development activities that can support the development of advanced fuel cycle options. In order to evaluate and screen fuel cycle systems in the ES study, nine criteria were used including Development and Deployment Risk (DDR). More specifically, this criterion was represented by the following metrics: Development time, development cost, deployment cost from prototypic validation to first-of-a-kind commercial, compatibility with the existing nuclear fuel cycle infrastructure, existence of regulations for the fuel cycle and familiarity with licensing, and existence of market incentives and/or barriers to commercial implementation of fuel cycle processes. Given the comprehensive nature of the study, a systematic approach was needed to determine metric data for the DDR criterion. As would be expected, the Evaluation Group representing the once-through use of uranium in thermal reactors is always the highest ranked fuel cycle Evaluation Group for this DDR criterion. Evaluation Groups that consist of once-through fuel cycles that use existing reactor types are consistently ranked very high. The highest ranked limited and continuous recycle fuel cycle Evaluation Groups are those that recycle Pu in thermal reactors. The lowest ranked fuel cycles are predominately continuous recycle single stage and multi-stage fuel cycles that involve TRU and/or U 233 recycle. (authors)

Promising design options for the encapsulated nuclear heat source reactor

International Nuclear Information System (INIS)

Conway, L.; Carelli, M.D.; Dzodzo, M.; Hossain, Q.; Brown, N.W.; Wade, D.C.; Sienick, J.J.; Greenspan, E.; Kastenberg, W.E.; Saphier, D.

2001-01-01

Promising design options for the Encapsulated Nuclear Heat Source (ENHS) liquid-metal cooled fast reactor were identified during the first year of the DOE NERI program sponsored feasibility study. Many opportunities for incorporation of innovations in design and fabrication were identified. Three of the innovations are hereby described: a novel IHX (intermediate heat exchanger) made of a relatively small number of rectangular channels, an ENHS module design featuring 100% natural circulation, and a novel conceptual design of core support and fuelling. As a result of the first year study the ENHS concept appears more practical and more promising than perceived at the outset of this study. (authors)

Promising design options for the encapsulated nuclear heat source reactor

Energy Technology Data Exchange (ETDEWEB)

Conway, L.; Carelli, M.D.; Dzodzo, M. [Westinghouse Science and Technology, Pittsburgh, PA (United States); Hossain, Q.; Brown, N.W. [Lawrence Livermore National Lab., CA (United States); Wade, D.C.; Sienick, J.J. [Argonne National Lab., IL (United States); Greenspan, E.; Kastenberg, W.E.; Saphier, D. [University of California Dept of Nuclear Engineering, Berkeley, CA (United States)

2001-07-01

Promising design options for the Encapsulated Nuclear Heat Source (ENHS) liquid-metal cooled fast reactor were identified during the first year of the DOE NERI program sponsored feasibility study. Many opportunities for incorporation of innovations in design and fabrication were identified. Three of the innovations are hereby described: a novel IHX (intermediate heat exchanger) made of a relatively small number of rectangular channels, an ENHS module design featuring 100% natural circulation, and a novel conceptual design of core support and fuelling. As a result of the first year study the ENHS concept appears more practical and more promising than perceived at the outset of this study. (authors)

Design study on advanced nuclear fuel recycle system. Conceptual design study of recycle system using molten salt

International Nuclear Information System (INIS)

Kasai, Y.; Kakehi, I.; Moro, T.; Higashi, T.; Tobe, K.; Kawamura, F.; Yonezawa, S.; Yoshiuji, T.

1998-10-01

Advanced recycle system engineering group of OEC (Oarai Engineering Center) has being carried out a design study of the advanced nuclear fuel recycle system using molten salt (electro-metallurgical process). This system is aiming for improvements of fuel cycle economy and reduction of environmental burden (MA recycles, Minimum of radioactive waste disposal), and also improvement of safety and nuclear non-proliferation. This report describes results of the design study that has been continued since December 1996. (1) A design concept of the advanced nuclear fuel recycle system, that is a module type recycles system of pyrochemical reprocessing and fuel re-fabrication was studied. The module system has advantage in balance of Pu recycle where modules are constructed in coincidence with the construction plan of nuclear power plants, and also has flexibility for technology progress. A demonstration system, minimum size of the above module, was studies. This system has capacity of 10 tHM/y and is able to demonstrate recycle technology of MOX fuel, metal fuel and nitride fuel. (2) Each process of the system, which are pyrochemical electrorefining system, cathode processor, de-cladding system, waste disposal system, etc., were studied. In this study, capacity of an electrorefiner was discussed, and vitrification experiment of molten salt using lead-boric acid glass was conducted. (3) A hot cell system and material handling system of the demonstration system was studied. A robot driven by linear motor was studied for the handling system, and an arrangement plan of the cell system was made. Criticality analysis in the cell system and investigation of material accountancy system of the recycle plant were also made. This design study will be continued in coincidence with design study of reactor and fuel, aiming to establish the concept of FBR recycle system. (author)

How Does the Innovation System in the Spanish Ceramic Tile Sector Function?

Energy Technology Data Exchange (ETDEWEB)

Gabaldon-Estevan, D.; Hekkert, M. P.

2013-06-01

In this article we apply the functions of innovation systems framework to assess its appropriateness to characterise the innovation activity of the tile industry in Castellon. This framework is based on idea that a well functioning innovation system requires that a number of key activities take place. If this occurs innovative output is higher. Our analysis provides a deeper understanding of the role of innovation as a strategic option in a mature industry in the context of globalisation. By applying this new theoretical approach to study innovation and highlighting the functions that the system requires, we shown the constraints, inertias, challenges and opportunities that the innovation system of the tile industry in Castellon faces. The results also show that the functional approach allows higher flexibility in order to recognise and analyse the opportunities and constraints that a given innovation system presents. (Author) 20 refs.

Filter Backwash Recycling Rule Documents

Science.gov (United States)

The purpose of the FBRR is to require (PWSs) to review their recycle practices and, where appropriate, work with the state Primacy Agency to make any necessary changes to recycle practices that may compromise microbial control.

Coal liquefaction with preasphaltene recycle

Science.gov (United States)

Weimer, Robert F.; Miller, Robert N.

1986-01-01

A coal liquefaction system is disclosed with a novel preasphaltene recycle from a supercritical extraction unit to the slurry mix tank wherein the recycle stream contains at least 90% preasphaltenes (benzene insoluble, pyridine soluble organics) with other residual materials such as unconverted coal and ash. This subject process results in the production of asphaltene materials which can be subjected to hydrotreating to acquire a substitute for No. 6 fuel oil. The preasphaltene-predominant recycle reduces the hydrogen consumption for a process where asphaltene material is being sought.

Overview of HTGR fuel recycle

International Nuclear Information System (INIS)

Notz, K.J.

1976-01-01

An overview of HTGR fuel recycle is presented, with emphasis placed on reprocessing and fuel kernel refabrication. Overall recycle operations include (1) shipment and storage, (2) reprocessing, (3) refabrication, (4) waste handling, and (5) accountability and safeguards

How Experiments in the Fuzzy Front End Using Prototyping Generates New Options

DEFF Research Database (Denmark)

Christiansen, John K.; Gasparin, Marta

2017-01-01

be characterized as various forms of prototyping. Interestingly the prototyping and experiments took place in the very early phases of the innovation process, rather than later as often advised and interestingly experimentation in the cases here appears to be a vehicle for creating new options. Furthermore......, the analysis demonstrates that prototyping can be considered as a punctuation device, as it offers those involved the option of opting out of ongoing processes, routines and engage in playful behavior by allowing for a freer experimentation with materials, processes, methods to challenge existing knowledge...

Sustaining the environment through recycling: an empirical study.

Science.gov (United States)

Ramayah, T; Lee, Jason Wai Chow; Lim, Shuwen

2012-07-15

This paper examines the determinants of recycling behaviour among 200 university students from the perspective of the theory of planned behaviour (TPB). Data was analysed using Structural Equation Modelling technique. Findings indicate that environmental awareness was significantly related to attitude towards recycling, whilst attitude and social norms had significant impact on recycling behaviour. However, convenience and cost of recycling were not significant reasons for recycling. The study has enhanced the understanding of the determinants of recycling behaviour and has implications for schools and governmental agencies in educating and encouraging positive recycling behaviour. It also confirms the appropriateness of the TPB in examining studies of this nature. Further suggestions for future research are offered. Copyright © 2012 Elsevier Ltd. All rights reserved.

Recycling fusion materials

International Nuclear Information System (INIS)

Ooms, L.

2005-01-01

The inherent safety and environmental advantages of fusion power in comparison with other energy sources play an important role in the public acceptance. No waste burden for future generations is therefore one of the main arguments to decide for fusion power. The waste issue has thus been studied in several documents and the final conclusion of which it is stated that there is no permanent disposal waste needed if recycling is applied. But recycling of fusion reactor materials is far to be obvious regarding mostly the very high specific activity of the materials to be handled, the types of materials and the presence of tritium. The main objective of research performed by SCK-CEN is to study the possible ways of recycling fusion materials and analyse the challenges of the materials management from fusion reactors, based on current practices used in fission reactors and the requirements for the manufacture of fusion equipment

Recycling of polymers: a review.

Science.gov (United States)

Ignatyev, Igor A; Thielemans, Wim; Vander Beke, Bob

2014-06-01

Plastics are inexpensive, easy to mold, and lightweight. These and many other advantages make them very promising candidates for commercial applications. In many areas, they have substantially suppressed traditional materials. However, the problem of recycling still is a major challenge. There are both technological and economic issues that restrain the progress in this field. Herein, a state-of-art overview of recycling is provided together with an outlook for the future by using popular polymers such as polyolefins, poly(vinyl chloride), polyurethane, and poly(ethylene terephthalate) as examples. Different types of recycling, primary, secondary, tertiary, quaternary, and biological recycling, are discussed together with related issues, such as compatibilization and cross-linking. There are various projects in the European Union on research and application of these recycling approaches; selected examples are provided in this article. Their progress is mirrored by granted patents, most of which have a very limited scope and narrowly cover certain technologies. Global introduction of waste utilization techniques to the polymer market is currently not fully developed, but has an enormous potential. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Applying real options analysis to assess cleaner energy development strategies

International Nuclear Information System (INIS)

Cheng, Ching-Tsung; Lo, Shang-Lien; Lin, Tyrone T.

2011-01-01

The energy industry, accounts for the largest portion of CO 2 emissions, is facing the issue of compliance with the national clean energy policy. The methodology for evaluating the energy mix policy is crucial because of the characteristics of lead time embedded with the power generation facilities investment and the uncertainty of future electricity demand. In this paper, a modified binomial model based on sequential compound options, which may account for the lead time and uncertainty as a whole is established, and a numerical example on evaluating the optional strategies and the strategic value of the cleaner energy policy is also presented. It is found that the optimal decision at some nodes in the binomial tree is path dependent, which is different from the standard sequential compound option model with lead time or time lag concept. The proposed modified binomial sequential compound real options model can be generalized and extensively applied to solve the general decision problems that deal with the long lead time of many government policies as well as capital intensive investments. - Highlights: → Introducing a flexible strategic management approach for government policy making. → Developing a modified binomial real options model based on sequential compound options. → Proposing an innovative model for managing the long term policy with lead time. → Applying to evaluate the options of various scenarios of cleaner energy strategies.

Bayesian Option Pricing Framework with Stochastic Volatility for FX Data

Directory of Open Access Journals (Sweden)

Ying Wang

2016-12-01

Full Text Available The application of stochastic volatility (SV models in the option pricing literature usually assumes that the market has sufficient option data to calibrate the model’s risk-neutral parameters. When option data are insufficient or unavailable, market practitioners must estimate the model from the historical returns of the underlying asset and then transform the resulting model into its risk-neutral equivalent. However, the likelihood function of an SV model can only be expressed in a high-dimensional integration, which makes the estimation a highly challenging task. The Bayesian approach has been the classical way to estimate SV models under the data-generating (physical probability measure, but the transformation from the estimated physical dynamic into its risk-neutral counterpart has not been addressed. Inspired by the generalized autoregressive conditional heteroskedasticity (GARCH option pricing approach by Duan in 1995, we propose an SV model that enables us to simultaneously and conveniently perform Bayesian inference and transformation into risk-neutral dynamics. Our model relaxes the normality assumption on innovations of both return and volatility processes, and our empirical study shows that the estimated option prices generate realistic implied volatility smile shapes. In addition, the volatility premium is almost flat across strike prices, so adding a few option data to the historical time series of the underlying asset can greatly improve the estimation of option prices.

Long-term aging of recycled binders : [summary].

Science.gov (United States)

2015-10-01

At 80 million tons a year representing more than 80% of all milled asphalt pavement : asphalt paving is Americas most recycled material. Asphalt can be recycled in place, which is : very cost effective; however, aging of recycled binder ca...

Fast Spectrum Molten Salt Reactor Options

Energy Technology Data Exchange (ETDEWEB)

Gehin, Jess C [ORNL; Holcomb, David Eugene [ORNL; Flanagan, George F [ORNL; Patton, Bruce W [ORNL; Howard, Rob L [ORNL; Harrison, Thomas J [ORNL

2011-07-01

During 2010, fast-spectrum molten-salt reactors (FS-MSRs) were selected as a transformational reactor concept for light-water reactor (LWR)-derived heavy actinide disposition by the Department of Energy-Nuclear Energy Advanced Reactor Concepts (ARC) program and were the subject of a preliminary scoping investigation. Much of the reactor description information presented in this report derives from the preliminary studies performed for the ARC project. This report, however, has a somewhat broader scope-providing a conceptual overview of the characteristics and design options for FS-MSRs. It does not present in-depth evaluation of any FS-MSR particular characteristic, but instead provides an overview of all of the major reactor system technologies and characteristics, including the technology developments since the end of major molten salt reactor (MSR) development efforts in the 1970s. This report first presents a historical overview of the FS-MSR technology and describes the innovative characteristics of an FS-MSR. Next, it provides an overview of possible reactor configurations. The following design features/options and performance considerations are described including: (1) reactor salt options-both chloride and fluoride salts; (2) the impact of changing the carrier salt and actinide concentration on conversion ratio; (3) the conversion ratio; (4) an overview of the fuel salt chemical processing; (5) potential power cycles and hydrogen production options; and (6) overview of the performance characteristics of FS-MSRs, including general comparative metrics with LWRs. The conceptual-level evaluation includes resource sustainability, proliferation resistance, economics, and safety. The report concludes with a description of the work necessary to begin more detailed evaluation of FS-MSRs as a realistic reactor and fuel cycle option.

Waste management considerations in HTGR recycle operations

International Nuclear Information System (INIS)

Pence, D.T.; Shefcik, J.J.; Heath, C.A.

1975-01-01

Waste management considerations in the recycle of HTGR fuel are different from those encountered in the recycle of LWR fuel. The types of waste associated with HTGR recycle operations are discussed, and treatment methods for some of the wastes are described

New options to integrate care and financing for persons dually eligible for Medicare and Medicaid.

Science.gov (United States)

Hayes, Katherine Jett; Thorpe, Jane Hyatt

2012-01-01

This paper reviews barriers to clinical and financial integration in services for dual eligibles prior to passage of the ACA, identifies models used by states to integrate care through contract and waiver authorities available to CMS prior to passage of the ACA, describes two new demonstrations proposed by CMS through the Medicare-Medicaid Coordination Office and Innovation Center, and discusses several new models available for consideration by federal and state policymakers. These options draw on experience from existing programs and waivers to provide suggested changes to existing programs, as well as a permanent state plan option for a fully integrated, capitated care model. This model could be made available to states prior to the completion of the demonstration process begun by the Medicare-Medicaid Coordination Office and Innovation Center.

OPEN INNOVATION MODELS - A CASE STUDY OF PLAYING POKER WITH CHESS PIECES

DEFF Research Database (Denmark)

Goduscheit, René Chester; Jørgensen, Jacob Høj; Bergenholtz, Carsten

2009-01-01

The qualities of employing open innovation models are widely acknowledgedamong academics and practitioners. Open innovation is perceived as a meansto ensure flexibility and create options for future business. However, theorganisational challenges in employing open innovation models as opposed...... tomore closed ones are not extensively explored in the literature. This paperaddresses these organisational challenges. On the basis of an in-depth casestudy of a project from the Danish energy sector, two prominent approacheswithin the open innovation paradigm, user-driven and network......-basedinnovation, are discussed. The analysis indicates that the organisationsinvolved in the project are only implementing the open innovation models to alimited degree. While indicating that they are employing open innovationapproaches, they are actually operating within a traditional, closed innovationmindset and to a certain...

Financial oil derivatives: from options to oil warrants and synthetic oilfields

International Nuclear Information System (INIS)

Trabia, Xavier

1992-01-01

This study aims to shed light on some of the most interesting financial oil derivatives issued so far in order to assess the potential of this new wave of innovative funding instruments. In Part I some theoretical background is provided and applied to the problem of the American futures option. The ''binomial'' model for valuing future option contracts is presented and the most accurate alternatives for pricing American futures options are reviewed. The role of these numerical procedures in valuing more complex options involved in oil warrants is examined. Comments are made on the behaviour of volatility, which stands as a key interface between theory and practice in oil trading on the oil futures market. Part II of the study describes in detail some of the most famous new financial oil derivatives. Some final conclusions are drawn on the potential of oil trusts and synthetic oilfields to be involved in project and general funding in the oil industry. (44 figures, 11 tables, 53 references) (UK)

Concrete Waste Recycling Process for High Quality Aggregate

International Nuclear Information System (INIS)

Ishikura, Takeshi; Fujii, Shin-ichi

2008-01-01

Large amount of concrete waste generates during nuclear power plant (NPP) dismantling. Non-contaminated concrete waste is assumed to be disposed in a landfill site, but that will not be the solution especially in the future, because of decreasing tendency of the site availability and natural resources. Concerning concrete recycling, demand for roadbeds and backfill tends to be less than the amount of dismantled concrete generated in a single rural site, and conventional recycled aggregate is limited of its use to non-structural concrete, because of its inferior quality to ordinary natural aggregate. Therefore, it is vital to develop high quality recycled aggregate for general uses of dismantled concrete. If recycled aggregate is available for high structural concrete, the dismantling concrete is recyclable as aggregate for industry including nuclear field. Authors developed techniques on high quality aggregate reclamation for large amount of concrete generated during NPP decommissioning. Concrete of NPP buildings has good features for recycling aggregate; large quantity of high quality aggregate from same origin, record keeping of the aggregate origin, and little impurities in dismantled concrete such as wood and plastics. The target of recycled aggregate in this development is to meet the quality criteria for NPP concrete as prescribed in JASS 5N 'Specification for Nuclear Power Facility Reinforced Concrete' and JASS 5 'Specification for Reinforced Concrete Work'. The target of recycled aggregate concrete is to be comparable performance with ordinary aggregate concrete. The high quality recycled aggregate production techniques are assumed to apply for recycling for large amount of non-contaminated concrete. These techniques can also be applied for slightly contaminated concrete dismantled from radiological control area (RCA), together with free release survey. In conclusion: a technology on dismantled concrete recycling for high quality aggregate was developed

What do we know about metal recycling rates?

Science.gov (United States)

Graedel, T.E.; Allwood, J.; Birat, J.-P.; Buchert, M.; Hageluken, C.; Reck, B.K.; Sibley, S.F.; Sonnemann, G.

2011-01-01

The recycling of metals is widely viewed as a fruitful sustainability strategy, but little information is available on the degree to which recycling is actually taking place. This article provides an overview on the current knowledge of recycling rates for 60 metals. We propose various recycling metrics, discuss relevant aspects of recycling processes, and present current estimates on global end-of-life recycling rates (EOL-RR; i.e., the percentage of a metal in discards that is actually recycled), recycled content (RC), and old scrap ratios (OSRs; i.e., the share of old scrap in the total scrap flow). Because of increases in metal use over time and long metal in-use lifetimes, many RC values are low and will remain so for the foreseeable future. Because of relatively low efficiencies in the collection and processing of most discarded products, inherent limitations in recycling processes, and the fact that primary material is often relatively abundant and low-cost (which thereby keeps down the price of scrap), many EOL-RRs are very low: Only for 18 metals (silver, aluminum, gold, cobalt, chromium, copper, iron, manganese, niobium, nickel, lead, palladium, platinum, rhenium, rhodium, tin, titanium, and zinc) is the EOL-RR above 50% at present. Only for niobium, lead, and ruthenium is the RC above 50%, although 16 metals are in the 25% to 50% range. Thirteen metals have an OSR greater than 50%. These estimates may be used in considerations of whether recycling efficiencies can be improved; which metric could best encourage improved effectiveness in recycling; and an improved understanding of the dependence of recycling on economics, technology, and other factors. ?? 2011 by Yale University.

Energetic conditions of effective recycling of composite castings

OpenAIRE

J. Jackowski

2009-01-01

The most reasonable way of recycling the metal composite materials consists in separation of the components. In case of the composites with saturated reinforcement it is the only recycling method. The process of separation of the components always undergoes in the presence of an additional liquid phase called a recycling medium. In a three-phase system including the material of composite reinforcement – liquid composite matrix – liquid recycling medium, an important role for the recycling pro...

Municipal solid waste options : integrating organics management and residual disposal treatment : executive summary

Energy Technology Data Exchange (ETDEWEB)

Cant, M. (comp.) [Totten Sims Hubicki Associates Ltd., Calgary, AB (Canada); Van der Werf, P. [2cg Inc., Edmonton, AB (Canada); Kelleher, M. [Kelleher Environmental, Toronto, ON (Canada); Merriman, D. [MacViro Consultants, Markham, ON (Canada); Fitcher, K. [Gartner Lee Ltd., Toronto, ON (Canada); MacDonald, N. [CH2M Hill Engineering Ltd., Calgary, AB (Canada)

2006-04-15

The Municipal Solid Waste (MSW) Options Report explored different MSW management options for 3 community sizes: 20,000, 80,000 and 200,0000 people. It was released at a time when many communities were developing waste management plans to cost-effectively reduce environmental impacts and conserve landfill capacity. The purpose of this report was to provide a greater understanding on the environmental, social, economic, energy recovery/utilization and greenhouse gas (GHG) considerations of MSW management. The report also demonstrated the interrelationships between the management of organics and residuals. It was based on information from existing waste diversion and organics management options and emerging residual treatment technology options. The following organics management and residual treatment disposal options were evaluated: composting; anaerobic digestion; sanitary landfills; bioreactor landfills; and thermal treatment. Composting was examined with reference to both source separated organics (SSO) and mixed waste composting. SSO refers to the separation of materials suitable for composting solid waste from households, while mixed waste composting refers to the manual or mechanical removal of recyclable material from the waste, including compost. The composting process was reviewed along with available technologies such as non-reactor windrow; aerated static pile; reactor enclosed channel; and, container tunnel. An evaluation of SSO and mixed waste composting was then presented in terms of environmental, social, financial and GHG impacts. refs., tabs., figs.

Recyclability of PET/WPI/PE Multilayer Films by Removal of Whey Protein Isolate-Based Coatings with Enzymatic Detergents

Directory of Open Access Journals (Sweden)

Patrizia Cinelli

2016-06-01

Full Text Available Multilayer plastic films provide a range of properties, which cannot be obtained from monolayer films but, at present, their recyclability is an open issue and should be improved. Research to date has shown the possibility of using whey protein as a layer material with the property of acting as an excellent barrier against oxygen and moisture, replacing petrochemical non-recyclable materials. The innovative approach of the present research was to achieve the recyclability of the substrate films by separating them, with a simple process compatible with industrial procedures, in order to promote recycling processes leading to obtain high value products that will beneficially impact the packaging and food industries. Hence, polyethyleneterephthalate (PET/polyethylene (PE multi-layer film was prepared based on PET coated with a whey protein layer, and then the previous structure was laminated with PE. Whey proteins, constituting the coating, can be degraded by enzymes so that the coating films can be washed off from the plastic substrate layer. Enzyme types, dosage, time, and temperature optima, which are compatible with procedures adopted in industrial waste recycling, were determined for a highly-efficient process. The washing of samples based on PET/whey and PET/whey/PE were efficient when performed with enzymatic detergent containing protease enzymes, as an alternative to conventional detergents used in recycling facilities. Different types of enzymatic detergents tested presented positive results in removing the protein layer from the PET substrate and from the PET/whey/PE multilayer films at room temperature. These results attested to the possibility of organizing the pre-treatment of the whey-based multilayer film by washing with different available commercial enzymatic detergents in order to separate PET and PE, thus allowing a better recycling of the two different polymers. Mechanical properties of the plastic substrate, such as stress at

Recyclability of PET/WPI/PE Multilayer Films by Removal of Whey Protein Isolate-Based Coatings with Enzymatic Detergents

Science.gov (United States)

Cinelli, Patrizia; Schmid, Markus; Bugnicourt, Elodie; Coltelli, Maria Beatrice; Lazzeri, Andrea

2016-01-01

Multilayer plastic films provide a range of properties, which cannot be obtained from monolayer films but, at present, their recyclability is an open issue and should be improved. Research to date has shown the possibility of using whey protein as a layer material with the property of acting as an excellent barrier against oxygen and moisture, replacing petrochemical non-recyclable materials. The innovative approach of the present research was to achieve the recyclability of the substrate films by separating them, with a simple process compatible with industrial procedures, in order to promote recycling processes leading to obtain high value products that will beneficially impact the packaging and food industries. Hence, polyethyleneterephthalate (PET)/polyethylene (PE) multi-layer film was prepared based on PET coated with a whey protein layer, and then the previous structure was laminated with PE. Whey proteins, constituting the coating, can be degraded by enzymes so that the coating films can be washed off from the plastic substrate layer. Enzyme types, dosage, time, and temperature optima, which are compatible with procedures adopted in industrial waste recycling, were determined for a highly-efficient process. The washing of samples based on PET/whey and PET/whey/PE were efficient when performed with enzymatic detergent containing protease enzymes, as an alternative to conventional detergents used in recycling facilities. Different types of enzymatic detergents tested presented positive results in removing the protein layer from the PET substrate and from the PET/whey/PE multilayer films at room temperature. These results attested to the possibility of organizing the pre-treatment of the whey-based multilayer film by washing with different available commercial enzymatic detergents in order to separate PET and PE, thus allowing a better recycling of the two different polymers. Mechanical properties of the plastic substrate, such as stress at yield, stress and

Options for treating high-temperature gas-cooled reactor fuel for repository disposal

Energy Technology Data Exchange (ETDEWEB)

Lotts, A.L.; Bond, W.D.; Forsberg, C.W.; Glass, R.W.; Harrington, F.E.; Micheals, G.E.; Notz, K.J.; Wymer, R.G.

1992-02-01

This report describes the options that can reasonably be considered for disposal of high-temperature gas-cooled reactor (HTGR) fuel in a repository. The options include whole-block disposal, disposal with removal of graphite (either mechanically or by burning), and reprocessing of spent fuel to separate the fuel and fission products. The report summarizes what is known about the options without extensively projecting or analyzing actual performance of waste forms in a repository. The report also summarizes the processes involved in convert spent HTGR fuel into the various waste forms and projects relative schedules and costs for deployment of the various options. Fort St. Vrain Reactor fuel, which utilizes highly-enriched {sup 235}U (plus thorium) and is contained in a prismatic graphite block geometry, was used as the baseline for evaluation, but the major conclusions would not be significantly different for low- or medium-enriched {sup 235}U (without thorium) or for the German pebble-bed fuel. Future US HTGRs will be based on the Fort St. Vrain (FSV) fuel form. The whole block appears to be a satisfactory waste form for disposal in a repository and may perform better than light-water reactor (LWR) spent fuel. From the standpoint of process cost and schedule (not considering repository cost or value of fuel that might be recycled), the options are ranked as follows in order of increased cost and longer schedule to perform the option: (1) whole block, (2a) physical separation, (2b) chemical separation, and (3) complete chemical processing.

Options for treating high-temperature gas-cooled reactor fuel for repository disposal

International Nuclear Information System (INIS)

Lotts, A.L.; Bond, W.D.; Forsberg, C.W.; Glass, R.W.; Harrington, F.E.; Micheals, G.E.; Notz, K.J.; Wymer, R.G.

1992-02-01

This report describes the options that can reasonably be considered for disposal of high-temperature gas-cooled reactor (HTGR) fuel in a repository. The options include whole-block disposal, disposal with removal of graphite (either mechanically or by burning), and reprocessing of spent fuel to separate the fuel and fission products. The report summarizes what is known about the options without extensively projecting or analyzing actual performance of waste forms in a repository. The report also summarizes the processes involved in convert spent HTGR fuel into the various waste forms and projects relative schedules and costs for deployment of the various options. Fort St. Vrain Reactor fuel, which utilizes highly-enriched 235 U (plus thorium) and is contained in a prismatic graphite block geometry, was used as the baseline for evaluation, but the major conclusions would not be significantly different for low- or medium-enriched 235 U (without thorium) or for the German pebble-bed fuel. Future US HTGRs will be based on the Fort St. Vrain (FSV) fuel form. The whole block appears to be a satisfactory waste form for disposal in a repository and may perform better than light-water reactor (LWR) spent fuel. From the standpoint of process cost and schedule (not considering repository cost or value of fuel that might be recycled), the options are ranked as follows in order of increased cost and longer schedule to perform the option: (1) whole block, (2a) physical separation, (2b) chemical separation, and (3) complete chemical processing

Physico-chemical properties of excavated plastic from landfill mining and current recycling routes.

Science.gov (United States)

Canopoli, L; Fidalgo, B; Coulon, F; Wagland, S T

2018-06-01

In Europe over 5.25 billion tonnes of waste has been landfilled between 1995 and 2015. Among this large amount of waste, plastic represents typically 5-25 wt% which is significant and has the potential to be recycled and reintroduced into the circular economy. To date there is still however little information available of the opportunities and challenges in recovering plastics from landfill sites. In this review, the impacts of landfill chemistry on the degradation and/or contamination of excavated plastic waste are analysed. The feasibility of using excavated plastic waste as feedstock for upcycling to valuable chemicals or liquid fuels through thermochemical conversion is also critically discussed. The limited degradation that is experienced by many plastics in landfills (>20 years) which guarantee that large amount is still available is largely due to thermooxidative degradation and the anaerobic conditions. However, excavated plastic waste cannot be conventionally recycled due to high level of ash, impurities and heavy metals. Recent studies demonstrated that pyrolysis offers a cost effective alternative option to conventional recycling. The produced pyrolysis oil is expected to have similar characteristics to petroleum diesel oil. The production of valuable product from excavated plastic waste will also increase the feasibility of enhanced landfill mining projects. However, further studies are needed to investigate the uncertainties about the contamination level and degradation of excavated plastic waste and address their viability for being processed through pyrolysis. Copyright © 2018 Elsevier Ltd. All rights reserved.

Is Municipal Solid Waste Recycling Economically Efficient?

Science.gov (United States)

Lavee, Doron

2007-12-01

It has traditionally been argued that recycling municipal solid waste (MSW) is usually not economically viable and that only when externalities, long-term dynamic considerations, and/or the entire product life cycle are taken into account, recycling becomes worthwhile from a social point of view. This article explores the results of a wide study conducted in Israel in the years 2000 2004. Our results reveal that recycling is optimal more often than usually claimed, even when externality considerations are ignored. The study is unique in the tools it uses to explore the efficiency of recycling: a computer-based simulation applied to an extensive database. We developed a simulation for assessing the costs of handling and treating MSW under different waste-management systems and used this simulation to explore possible cost reductions obtained by designating some of the waste (otherwise sent to landfill) to recycling. We ran the simulation on data from 79 municipalities in Israel that produce over 60% of MSW in Israel. For each municipality, we were able to arrive at an optimal method of waste management and compare the costs associated with 100% landfilling to the costs born by the municipality when some of the waste is recycled. Our results indicate that for 51% of the municipalities, it would be efficient to adopt recycling, even without accounting for externality costs. We found that by adopting recycling, municipalities would be able to reduce direct costs by an average of 11%. Through interviews conducted with representatives of municipalities, we were also able to identify obstacles to the utilization of recycling, answering in part the question of why actual recycling levels in Israel are lower than our model predicts they should be.

Advanced policy options to regulate sugar-sweetened beverages to support public health.

Science.gov (United States)

Pomeranz, Jennifer L

2012-02-01

Consumption of sugar-sweetened beverages (SSBs) has increased worldwide. As public health studies expose the detrimental impact of SSBs, consumer protection and public health advocates have called for increased government control. A major focus has been on restricting marketing of SSBs to children, but many innovative policy options--legally defensible ways to regulate SSBs and support public health--are largely unexplored. We describe the public health, economic, and retail marketing research related to SSBs (including energy drinks). We review policy options available to governments, including mandatory factual disclosures, earmarked taxation, and regulating sales, including placement within retail and food service establishments, and schools. Our review describes recent international initiatives and classifies options available in the United States by jurisdiction (federal, state, and local) based on legal viability.

India's ship recycling trade-off

NARCIS (Netherlands)

Worrell, E.; Athanasopoulou, V.

2014-01-01

The special nature of India's steel industry lends particular importance to ship recycling as a source of scrap. Ship recycling in upgraded 'green' facilities can substitute other 'dirty' ironmaking processes, resulting in energy savings and air pollutant emission reductions for the Indian steel

Process options and projected mass flows for the HTGR refabrication scrap recovery system

International Nuclear Information System (INIS)

Tiegs, S.M.

1979-03-01

The two major uranium recovery processing options reviewed are (1) internal recovery of the scrap by the refabrication system and (2) transfer to and external recovery of the scrap by the head end of the reprocessing system. Each option was reviewed with respect to equipment requirements, preparatory processing, and material accountability. Because there may be a high cost factor on transfer of scrap fuel material to the reprocessing system for recovery, all of the scrap streams will be recycled internally within the refabrication system, with the exception of reject fuel elements, which will be transferred to the head end of the reprocessing system for uranium recovery. The refabrication facility will be fully remote; thus, simple recovery techniques were selected as the reference processes for scrap recovery. Crushing, burning, and leaching methods will be used to recover uranium from the HTGR refabrication scrap fuel forms, which include particles without silicon carbide coatings, particles with silicon carbide coatings, uncarbonized fuel rods, carbon furnace parts, perchloroethylene distillation bottoms, and analytical sample remnants. Mass flows through the reference scrap recovery system were calculated for the HTGR reference recycle facility operating with the highly enriched uranium fuel cycle. Output per day from the refabrication scrap recovery system is estimated to be 4.02 kg of 2355 U and 10.85 kg of 233 U. Maximum equipment capacities were determined, and future work will be directed toward the development and costing of the scrap recovery system chosen as reference

National Option of China's Nuclear Energy Systems for Spent Fuel Management

Energy Technology Data Exchange (ETDEWEB)

Gao, R.X. [University of Science and Technology, Daejeon (Korea, Republic of); Ko, W. I.; Lee, S. H. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

Along with safety concerns, these long standing environmental challenges are the major factors influencing the public acceptance of nuclear power. Although nuclear power plays an important role in reducing carbon emissions from energy generation, this could not fully prove it as a sustainable energy source unless we find a consensus approach to treat the nuclear wastes. There are currently no countries that have completed a whole nuclear fuel cycle, and the relative comparison of the reprocessing spent fuel options versus direct disposal option is always a controversial issue. Without exception, nowadays, China is implementing many R and D projects on spent fuel management to find a long-term solution for nuclear fuel cycle system transition, such as deep geological repositories for High Level Waste (HLW), Pu Reduction by Solvent Extraction (PUREX) technology, and fast reactor recycling Mixed U-Pu Oxide (MOX) fuels, etc. This paper integrates the current nation's projects of back-end fuel cycle, analyzes the consequences of potential successes, failures and delays in the project development to future nuclear fuel cycle transition up to 2100. We compared the dynamic results of four scenarios and then assessed relative impact on spent fuel management. The result revealed that the fuel cycle transition of reprocessing and recycling of spent fuel would bring advantages to overall nuclear systems by reducing high level waste inventory, saving natural uranium resources, and reducing plutonium management risk.

Mox fuels recycling

International Nuclear Information System (INIS)

Gay, A.

1998-01-01

This paper will firstly emphasis that the first recycling of plutonium is already an industrial reality in France thanks to the high degree of performance of La Hague and MELOX COGEMA's plants. Secondly, recycling of spent Mixed OXide fuel, as a complete MOX fuel cycle, will be demonstrated through the ability of the existing plants and services which have been designed to proceed with such fuels. Each step of the MOX fuel cycle concept will be presented: transportation, reception and storage at La Hague and steps of spent MOX fuel reprocessing. (author)

Prospects for natural gas in Europe. Market potential, political intervention and technological options

International Nuclear Information System (INIS)

Kabelitz, K.R.

1997-01-01

The potential market demand, the emerging fundamental political intervention in the European gas and electricity markets and the technological options available will give the gas industry in Europe a different appearance at the beginning of the 21. century. One of the key questions is: will the political intervention and technological options and innovations assist and promote the realisation of market potential? At the moment, it cannot be stated definitely whether the currently available technological options will allow the significant cost reductions hoped for in the entire gas chain to become reality in good time. Under these circumstances, a major mismatch would emerge between the market potential predicted for natural gas in Europe and the actual market development. (R.P.)

Recycling of Reinforced Plastics

Science.gov (United States)

Adams, R. D.; Collins, Andrew; Cooper, Duncan; Wingfield-Digby, Mark; Watts-Farmer, Archibald; Laurence, Anna; Patel, Kayur; Stevens, Mark; Watkins, Rhodri

2014-02-01

This work has shown is that it is possible to recycle continuous and short fibre reinforced thermosetting resins while keeping almost the whole of the original material, both fibres and matrix, within the recyclate. By splitting, crushing hot or cold, and hot forming, it is possible to create a recyclable material, which we designate a Remat, which can then be used to remanufacture other shapes, examples of plates and tubes being demonstrated. Not only can remanufacturing be done, but it has been shown that over 50 % of the original mechanical properties, such as the E modulus, tensile strength, and interlaminar shear strength, can be retained. Four different forms of composite were investigated, a random mat Glass Fibre Reinforced Plastic (GFRP) bathroom component and boat hull, woven glass and carbon fibre cloth impregnated with an epoxy resin, and unidirectional carbon fibre pre-preg. One of the main factors found to affect composite recyclability was the type of resin matrix used in the composite. Thermoset resins tested were shown to have a temperature range around the Glass Transition Temperature (Tg) where they exhibit ductile behaviour, hence aiding reforming of the material. The high-grade carbon fibre prepreg was found to be less easy to recycle than the woven of random fibre laminates. One method of remanufacturing was by heating the Remat to above its glass transition temperature, bending it to shape, and then cooling it. However, unless precautions are taken, the geometric form may revert. This does not happen with the crushed material.

76 FR 71861 - America Recycles Day, 2011

Science.gov (United States)

2011-11-18

... electronics annually, and without following proper recycling and management practices, the disposal of our old..., and prevent the recovery and reuse of valuable resources. For the well- being of our people and our..., management, and recycling that will accelerate our burgeoning electronics recycling market and create jobs...

On the logistics of recycling : an introduction

NARCIS (Netherlands)

Flapper, S.D.P.

1993-01-01

An overview is given of the different logistic aspects of recycling, where recycling denotes "All the activities required for the reuse of materials and (semi-)finished products after they are no longer used by their last user." Special attention is paid to the forced recycling of durable

Energy, innovation, and microprocessors: continuity in the research policy

Energy Technology Data Exchange (ETDEWEB)

Hauff, V [Bundesministerium fuer Forschung und Technologie, Bonn-Bad Godesberg (Germany, F.R.)

1978-07-01

The present West German Minister for Research and Technology took up his official duties three months ago. So Umschau asked some questions concerning his future policies. First, the minister confirmed the continuity of the existing science policies. In the field of energy he claimed that efficient and frugal use of energy is the priority. The second priority concerns the utilization of domestic coal. No hindrances in the further development of fast breeder reactors and nuclear recycling are expected. The Minister layed stress on the encouragement of technological innovations, which are indispensable for economic growth, given the present worldwide structural change in the division of labor; the country must search for very new products. Microelectronics will play a major role in future developments. The Minister gave some examples of new fields that present chances for innovative endeavors. Another field of interest is the forecasting models.

Hydrogen recycle modeling in transport codes

International Nuclear Information System (INIS)

Howe, H.C.

1979-01-01

The hydrogen recycling models now used in Tokamak transport codes are reviewed and the method by which realistic recycling models are being added is discussed. Present models use arbitrary recycle coefficients and therefore do not model the actual recycling processes at the wall. A model for the hydrogen concentration in the wall serves two purposes: (1) it allows a better understanding of the density behavior in present gas puff, pellet, and neutral beam heating experiments; and (2) it allows one to extrapolate to long pulse devices such as EBT, ISX-C and reactors where the walls are observed or expected to saturate. Several wall models are presently being studied for inclusion in transport codes

Life cycle assessment of post-consumer plastics production from waste electrical and electronic equipment (WEEE) treatment residues in a Central European plastics recycling plant

International Nuclear Information System (INIS)

Wäger, Patrick A.; Hischier, Roland

2015-01-01

Plastics play an increasingly important role in reaching the recovery and recycling rates defined in the European WEEE Directive. In a recent study we have determined the life cycle environmental impacts of post-consumer plastics production from mixed, plastics-rich WEEE treatment residues in the Central European plant of a market-leading plastics recycler, both from the perspective of the customers delivering the residues and the customers buying the obtained post-consumer recycled plastics. The results of our life cycle assessments, which were extensively tested with sensitivity analyses, show that from both perspectives plastics recycling is clearly superior to the alternatives considered in this study (i.e. municipal solid waste incineration (MSWI) and virgin plastics production). For the three ReCiPe endpoint damage categories, incineration in an MSWI plant results in an impact exceeding that of the examined plastics recycling facility each by about a factor of 4, and the production of virgin plastics has an impact exceeding that of the post-consumer recycled (PCR) plastics production each by a factor of 6–10. On a midpoint indicator level the picture is more differentiated, showing that the environmental impacts of the recycling options are lower by 50% and more for almost all impact factors. While this provides the necessary evidence for the environmental benefits of plastics recycling compared to existing alternatives, it can, however, not be taken as conclusive evidence. To be conclusive, future research will have to address the fate of hazardous substances in the outputs of such recycling systems in more detail. - Highlights: • LCA of plastics production from plastics-rich WEEE treatment residues • Multiple stakeholder perspectives addressed via different research questions • Plastics production from WEEE treatment residues clearly superior to alternatives • Robust results as demonstrated by extensive sensitivity analyses

Life cycle assessment of post-consumer plastics production from waste electrical and electronic equipment (WEEE) treatment residues in a Central European plastics recycling plant

Energy Technology Data Exchange (ETDEWEB)

Wäger, Patrick A., E-mail: patrick.waeger@empa.ch; Hischier, Roland

2015-10-01

Plastics play an increasingly important role in reaching the recovery and recycling rates defined in the European WEEE Directive. In a recent study we have determined the life cycle environmental impacts of post-consumer plastics production from mixed, plastics-rich WEEE treatment residues in the Central European plant of a market-leading plastics recycler, both from the perspective of the customers delivering the residues and the customers buying the obtained post-consumer recycled plastics. The results of our life cycle assessments, which were extensively tested with sensitivity analyses, show that from both perspectives plastics recycling is clearly superior to the alternatives considered in this study (i.e. municipal solid waste incineration (MSWI) and virgin plastics production). For the three ReCiPe endpoint damage categories, incineration in an MSWI plant results in an impact exceeding that of the examined plastics recycling facility each by about a factor of 4, and the production of virgin plastics has an impact exceeding that of the post-consumer recycled (PCR) plastics production each by a factor of 6–10. On a midpoint indicator level the picture is more differentiated, showing that the environmental impacts of the recycling options are lower by 50% and more for almost all impact factors. While this provides the necessary evidence for the environmental benefits of plastics recycling compared to existing alternatives, it can, however, not be taken as conclusive evidence. To be conclusive, future research will have to address the fate of hazardous substances in the outputs of such recycling systems in more detail. - Highlights: • LCA of plastics production from plastics-rich WEEE treatment residues • Multiple stakeholder perspectives addressed via different research questions • Plastics production from WEEE treatment residues clearly superior to alternatives • Robust results as demonstrated by extensive sensitivity analyses.

Innovative design, analysis and development practices in aerospace and automotive engineering

CERN Document Server

Chandrasekhar, U; Arankalle, Avinash

2014-01-01

The book presents the best articles presented by researchers, academicians and industrial experts in the International Conference on “Innovative Design, Analysis and Development Practices in Aerospace and Automotive Engineering”. The book discusses new concept designs, analysis and manufacturing technologies, where more swing is for improved performance through specific and/or multifunctional linguistic design aspects to downsize the system, improve weight to strength ratio, fuel efficiency, better operational capability at room and elevated temperatures, reduced wear and tear, NVH aspects while balancing the challenges of beyond Euro IV/Barat Stage IV emission norms, Greenhouse effects and recyclable materials. The innovative methods discussed in the book will serve as a reference material for educational and research organizations, as well as industry, to take up challenging projects of mutual interest.

Product innovation incentives by an incumbent firm : Dynamic analysis

NARCIS (Netherlands)

Dawid, H.; Keoula, M.Y.; Kopel, M.; Kort, Peter

We employ a dynamic framework to study how product innovation activities of a firm are influenced by its investments in production capacity of an established product and vice versa. The firm initially has capacity to sell an established product. Additionally, it also has the option to undertake an

Recycling of nonferrous metals from waste materials

Energy Technology Data Exchange (ETDEWEB)

Urban, A

1982-02-01

Recycling of metals was one of the 9 central subjects of the international symposium on 'Materials and Energy from Refuse', held in Antwerpen on October 20 to 22, 1981. Six of 65 poster sessions papers were on metal recycling; four of them discussed the recycling of nonferrous metals.

Recycling behaviour in healthcare: waste handling at work.