Boiling water reactor radiation shielded Control Rod Drive Housing Supports

Energy Technology Data Exchange (ETDEWEB)

Baversten, B.; Linden, M.J. [ABB Combustion Engineering Nuclear Operations, Windsor, CT (United States)

1995-03-01

The Control Rod Drive (CRD) mechanisms are located in the area below the reactor vessel in a Boiling Water Reactor (BWR). Specifically, these CRDs are located between the bottom of the reactor vessel and above an interlocking structure of steel bars and rods, herein identified as CRD Housing Supports. The CRD Housing Supports are designed to limit the travel of a Control Rod and Control Rod Drive in the event that the CRD vessel attachement went to fail, allowing the CRD to be ejected from the vessel. By limiting the travel of the ejected CRD, the supports prevent a nuclear overpower excursion that could occur as a result of the ejected CRD. The Housing Support structure must be disassembled in order to remove CRDs for replacement or maintenance. The disassembly task can require a significant amount of outage time and personnel radiation exposure dependent on the number and location of the CRDs to be changed out. This paper presents a way to minimize personal radiation exposure through the re-design of the Housing Support structure. The following paragraphs also delineate a method of avoiding the awkward, manual, handling of the structure under the reactor vessel during a CRD change out.

A pilot investigation of natural radiation in Danish houses

International Nuclear Information System (INIS)

Soerensen, A.; Boetter-Jensen, L.; Majborn, B.; Nielsen, S.P.

1985-04-01

As a prelude to a nationwide survey a pilot study was carried out to establish techniques and procedures for the measurement of indoor radiation in Denmark. A passive cup dosemeter was designed containing CR39 track detectors and TLD's to measure radon and external radiation, respectively. The adequate performance of the dosemeter was verified in a radon intercalibration in 1984 carried out at the National Radiological Protection Board, UK. A total of 82 dwellings were selected covering most regions of the country. The dwellings were monitored in two three-month periods, one in winter and the other in summer. The average dose rate in air from external radiation was 0.09 μGy h -1 . In the winter the average radon concentrations were 88 Bq m -3 and 24 Bq m -3 for single-family houses and flats, respectively; and in the summer the corresponding values were 52 Bq m -3 and 19 Bq m -3 . (author)

SAD phasing with in-house cu Ka radiation using barium as anomalous scatterer.

Science.gov (United States)

Dhanasekaran, V; Velmurugan, D

2011-12-01

Phasing of lysozyme crystals using co-crystallized barium ions was performed using single-wavelength anomalous diffraction (SAD) method using Cu Ka radiation with in-house source of data collection. As the ion binding sites vary with respect to the pH of the buffer during crystallization, the highly isomorphic forms of lysozyme crystals grown at acidic and alkaline pH were used for the study. Intrinsic sulphur anomalous signal was also utilized with anomalous signal from lower occupancy ions for phasing. The study showed that to solve the structure by SAD technique, 2.8-fold data redundancy was sufficient when barium was used as an anomalous marker in the in-house copper X-ray radiation source for data collection. Therefore, co-crystallization of proteins with barium containing salt can be a powerful tool for structure determination using lab source.

Response of tomato to radiation intensity and air temperature under plastic-house ultraviolet protection

International Nuclear Information System (INIS)

Syakur, A.

2002-01-01

Enhance of ultraviolet radiation intensity on the earth surface affected by ozon depletion on stratospheric layer cause changing on the response of plant to radiation quality. One technique for reducing photo destructive UV radiation is micro climate modification by using mulch and plastic-cover UV protection. So that, growth and yield of plant can be optimalized. This research designed an experiment to find out the effect of two kinds of plastic-cover, UV plastic and conventional plastic, on microclimate condition and tomato performance under plastic-house. The result of this research described that mulch and plastic cover can modify radiation and air temperature under plastics-house, but it can not improve growth and yield of the tomato [in

Application of the Positron Annihilation Spectroscopy for Chromium Effect Investigation in Binary Fe-Cr Alloys

International Nuclear Information System (INIS)

Sojak, S.; Krsjak, V.; Slugen, V.; Stancek, S.; Petriska, M.; Vitazek, K.; Stacho, M.

2008-01-01

Positron annihilation spectroscopy (PAS) is one of the non-destructive techniques applied with advantage for evaluation of the radiation treated materials microstructure. In this work, the PAS was used for study of different Fe-Cr alloys implanted by ions of helium. Investigation was focused on the chromium effect and the radiation defects resistance. In particular, the vacancy type defects (mono-vacancies, vacancy clusters) have been studied. The results show that the specific content of chromium has important influence on the size and distribution of induced defects. (authors)

Chromium in leather footwear-risk assessment of chromium allergy and dermatitis

DEFF Research Database (Denmark)

Thyssen, Jacob P; Strandesen, Maria; Poulsen, Pia B

2012-01-01

Background. Chromium-tanned leather footwear, which releases >3 ppm hexavalent Cr(VI), may pose a risk of sensitizing and eliciting allergic dermatitis. Objectives. To determine the content and potential release of chromium in leather footwear and to discuss the prevention of chromium contact...... allergy and dermatitis. Methods. Sixty pairs of leather shoes, sandals and boots (20 children's, 20 men's, and 20 women's) were purchased in Copenhagen and examined with X-ray fluorescence spectroscopy. Chromium was extracted according to the International Standard, ISO 17075. The detection level for Cr......(VI) was 3 ppm. Results. Chromium was identified in 95% of leather footwear products, the median content being 1.7% (range 0-3.3%). No association with store category or footwear category was found. A tendency for there to be a higher chromium content in footwear with high prices was shown (p(trend) = 0...

Radon as a radiation problem in underground mines and in houses - historical aspects

International Nuclear Information System (INIS)

Schuettmann, W.

1992-01-01

The paper briefly recalls the discovery of the radioisotope radon and the research into its properties and effects, referring among other things to the underground mining sites in the Erzgebirge and the Schneeberg lung disease. Today, the radiation exposure of underground miners in a radioactive environment is regarded to be a well-known risk manageable by today's state of the art in radiological protection. Radon as a radiation source in houses, however, remains the problem of great significance today. The paper reviews the current knowledge and approaches for solving this problem. (DG) [de

Determination of chromium combined with DNA, RNA and protein in chromium-rich brewer's yeast

International Nuclear Information System (INIS)

Ding Wenjun; Qian Qinfang; Hou Xiaolin; Feng Weiyue; Chai Zhifang

2000-01-01

The contents of chromium in the DNA, RNA and protein fractions separated from chromium-rich and normal brewer's yeast were determined with the neutron activation analysis in order to study the combination of Cr with DNA, RNA and protein in chromium-rich brewer's yeast. The results showed that the extracting rats and concentrations of DNA, RNA and protein had no significant difference in two types of yeast, but the chromium contents of DNA, RNA and protein in the chromium-rich yeast were significantly higher than those in the normal. In addition, the content of chromium in DNA was much higher than that in RNA and protein, which indicated that the inorganic chromium compounds entered into the yeast cell, during the yeast cultivation in the culture medium containing chromium were converted into organic chromium compounds combined with DNA, RNA and protein

Determination of chromium(III) and total chromium in marine waters

Energy Technology Data Exchange (ETDEWEB)

Gardner, M J [WRc, Henley Road, Medmenham, Marlow SL7 2HD (United Kingdom); Ravenscroft, J E [WRc, Henley Road, Medmenham, Marlow SL7 2HD (United Kingdom)

1996-03-01

The development of an analytical technique is described which may be used to determine chromium, chromium(III) and chromium(VI) in estuarine and coastal waters. The method is based on selective micro-solvent extraction with subsequent GFAAS. The technique has been applied in a major North Sea estuary. The results obtained confirm that thermodynamic factors alone cannot be relied upon to describe the form of chromium in estuaries. Kinetic factors appear to have a strong influence over speciation and lead to the persistence of Cr(III) species in environments where Cr(VI) would be expected to be present. (orig.). With 5 figs., 2 tabs.

Determination of carbon in chromium by photon activation

Energy Technology Data Exchange (ETDEWEB)

Fedoroff, M; Loos-Neskovic, C; Revel, G [Centre National de la Recherche Scientifique, 94 - Vitry-sur-Seine (France). Centre d' Etudes de Chimie Metallurgique

1975-01-01

Carbon is determined in chromium by activation in 35 MeV photons. The sample is dissolved by a fused NaOH-NaNO/sub 3/ bath. Carbon dioxide is then extracted by acid dissolution of the solidified bath. A limit of detection of 0.03 ..mu..g of carbon is achieved. Chromium samples are irradiated in photons emitted from a platinum target submitted to an electron beam of 35 MeV produced by a linear accelerator at C.E.N. Saclay. Two graphite foils of some mg are irradiated at the same time and are used as standards. The radioactivities of absorbers and standards are measured on a NaI detector for the annihilation ..gamma..-ray of the ..beta../sup +/radiation.

Radiation doses from radon and progeny in Irish houses

International Nuclear Information System (INIS)

McLaughlin, J.P.

1985-08-01

In the United Kingdom, the estimated average annual effective dose equivalent to members of the public from all sources is 2.4 mSv (240 mrem). 40% of this dose is contributed by exposure to radon, and it is not unreasonable to assume that the situation in Ireland is very similar. During 1982-84 a preliminary study of radon and penetrating radiation on 300 Irish houses showed seasonally averaged indoor radon concentrations in the range 3 Bq/m 3 of air to 700 bq/m 3 , with a median value of about 40 bq/m 3 . A national survey of indoor radon has now been undertaken; 3000 households, randomly selected from the electoral register are to be monitored and the result correlated with energy conservation practices. The final part of this document deals with the regulatory aspects of radon control and reviews the practices for reduction of indoor radon daughter doses presently in hand in Scandinavia. An appendix of radiation units and terms is also given

X-Ray Fluorescence Determination of the Surface Density of Chromium Nanolayers

Science.gov (United States)

Mashin, N. I.; Chernjaeva, E. A.; Tumanova, A. N.; Ershov, A. A.

2014-01-01

An auxiliary system consisting of thin-film layers of chromium deposited on a polymer film substrate is used to construct calibration curves for the relative intensities of the K α lines of chromium on bulk substrates of different elements as functions of the chromium surface density in the reference samples. Correction coefficients are calculated to take into account the absorption of primary radiation from an x-ray tube and analytical lines of the constituent elements of the substrate. A method is developed for determining the surface density of thin films of chromium when test and calibration samples are deposited on substrates of different materials.

Radiation shielding provided by residential houses in Japan in reactor accidents accompanied with atmospheric release

International Nuclear Information System (INIS)

Yamaguchi, Yasuhiro; Minami, Kentaro

1991-01-01

The present report describes the radiation shielding effect of houses in Japan against the radioactive cloud resulting from a major reactor accident accompanied with atmospheric release. The shielding factor of houses, the ratio of indoor exposure rate to outdoor one, has been studied for the semi-infinite and finite clouds which contain γ-emitting radionuclides released from a reactor facility. The shielding factor of houses against γ-rays from the radioactive cloud decreases gradually with release delay time and keeps a minimum during the period from 50 to 1000 hours after reactor shutdown while 133 Xe predominates in the cloud. Radioiodines mixed in the cloud raise slightly the shielding factor, and the factor depends little on the shape of the cloud. A set of shielding factors for the use of emergency planning was consequently proposed as 0.4 for simple ferroconcrete residential house and 0.9 for other ordinary ones. (author)

Studies of ion implanted thermally oxidised chromium

International Nuclear Information System (INIS)

Muhl, S.

1977-01-01

The thermal oxidation of 99.99% pure chromium containing precise amounts of foreign elements has been studied and compared to the oxidation of pure chromium. Thirty-three foreign elements including all of the naturally occurring rare earth metals were ion implanted into chromium samples prior to oxidation at 750 0 C in oxygen. The role of radiation induced damage, inherent in this doping technique, has been studied by chromium implantations at various energies and doses. The repair of the damage has been studied by vacuum annealing at temperatures up to 800 0 C prior to oxidation. Many of the implants caused an inhibition of oxidation, the greatest being a 93% reduction for 2 x 10 16 ions/cm 2 of praseodymium. The distribution of the implant was investigated by the use of 2 MeV alpha backscattering and ion microprobe analysis. Differences in the topography and structure of the chromic oxide on and off the implanted area were studied using scanning electron and optical microscopy. X-ray diffraction analysis was used to investigate if a rare earth-chromium compound of a perovskite-type structure had been formed. Lastly, the electrical conductivity of chromic oxide on and off the implanted region was examined at low voltages. (author)

Environmental gamma radiation measurements in Bangladeshi houses

International Nuclear Information System (INIS)

Idrish Miah, M.

2002-01-01

The indoor gamma dose rate in air measured using TLDs in the Dhaka district is not wide ranging and follows a normal distribution with an arithmetic mean of 1.54±0.26 mGy.y -1 . The result has been compared with those found by other investigators for different locations of the world. Measurements were made on a monthly basis for a year period, and a sinusoidal variation of monthly indoor gamma radiation of the type: d = 160 + 65 cos p/6 (m -1 ), where d is the indoor dose rate (nGy.h -1 ) and m the month, was observed. This might be due to seasonally varied air exchange rates of the houses. The average annual effective dose and the collective dose equivalent for the residents were estimated to be 0.86 mSv and 172.20 man-Sv respectively based on the indoor gamma exposure. (author)

Environmental gamma radiation measurements in Bangladeshi houses

International Nuclear Information System (INIS)

Miah, M.I.

2004-01-01

Indoor gamma dose rate in air measured using TLDs in the Dhaka district is not wide ranging and follows a normal distribution with an arithmetic mean of 1.54±0.26 mGy y -1 . The result has been compared with those found by other investigators for different locations of the world. Measurements were made on a monthly basis for a year period, and a sinusoidal variation of monthly indoor gamma radiation of the type: d=160+65 cos π/6 (m-1), where d is the indoor dose rate (nGy h -1 ) and m the month. This might be due to the seasonally varied air exchange rates of the houses. The average annual effective dose and the collective dose equivalent for the residents were estimated to be 0.86 mSv and 172.20 man-Sv, respectively, based on the indoor gamma exposure

Environmental gamma radiation measurements in Bangladeshi houses

Energy Technology Data Exchange (ETDEWEB)

Miah, M.I. E-mail: idrish_physics@yahoo.com

2004-06-01

Indoor gamma dose rate in air measured using TLDs in the Dhaka district is not wide ranging and follows a normal distribution with an arithmetic mean of 1.54{+-}0.26 mGy y{sup -1}. The result has been compared with those found by other investigators for different locations of the world. Measurements were made on a monthly basis for a year period, and a sinusoidal variation of monthly indoor gamma radiation of the type: d=160+65 cos {pi}/6 (m-1), where d is the indoor dose rate (nGy h{sup -1}) and m the month. This might be due to the seasonally varied air exchange rates of the houses. The average annual effective dose and the collective dose equivalent for the residents were estimated to be 0.86 mSv and 172.20 man-Sv, respectively, based on the indoor gamma exposure.

Mechanistic issues for modeling radiation-induced segregation

International Nuclear Information System (INIS)

Simonen, E.P.; Bruemmer, S.M.

1993-03-01

Model calculations of radiation-induced chromium depletion and radiation-induced nickel enrichment at grain boundaries are compared to measured depletions and enrichments. The model is calibrated to fit chromium depletion in commercial purity 304 stainless steel irradiated in boiling water reactor (BWR) environments. Predicted chromium depletion profiles and the dose dependence of chromium concentration at grain boundaries are in accord with measured trends. Evaluation of chromium and nickel profiles in three neutron, and two ion, irradiation environments reveal significant inconsistencies between measurements and predictions

Chromium in aqueous nitrate plutonium process streams: Corrosion of 316 stainless steel and chromium speciation

International Nuclear Information System (INIS)

Smith, W.H.; Purdy, G.M.

1995-01-01

This study was undertaken to determine if chromium(+6) could exist in plutonium process solutions under normal operating conditions. Four individual reactions were studied: the rate of dissolution of stainless steel, which is the principal source of chromium in process solutions; the rate of oxidation of chromium(+3) to chromium(+6) by nitric acid; and the reduction of chromium(+6) back to chromium(+3) by reaction with stainless steel and with oxalic acid. The stainless steel corrosion rate was found to increase with increasing nitric acid concentration, increasing hydrofluoric acid concentration, and increasing temperature. Oxidation of chromium(+3) to chromium(+6) was negligible at room temperature and only became significant in hot concentrated nitric acid. The rate of reduction of chromium(+6) back to chromium(+3) by reaction with stainless steel or oxalic acid was found to be much greater than the rate of the reverse oxidation reaction. Based on these findings and taking into account normal operating conditions, it was determined that although there would be considerable chromium in plutonium process streams it would rarely be found in the (+6) oxidation state and would not exist in the (+6) state in the final process waste solutions

Chromium in aqueous nitrate plutonium process streams: Corrosion of 316 stainless steel and chromium speciation

International Nuclear Information System (INIS)

Smith, W.H.; Purdy, G.

1995-01-01

This study was undertaken to determine if chromium +6 could exist in plutonium process solutions under normal operating conditions. Four individual reactions were studied: the rate of dissolution of stainless steel, which is the principal source of chromium in process solutions; the rate of oxidation of chromium +3 to chromium +6 by nitric. acid; and the reduction of chromium +6 back to chromium +3 by reaction with stainless steel and with oxalic acid. The stainless steel corrosion rate was found to increase with increasing nitric acid concentration, increasing hydrofluoric acid concentration, and increasing temperature. Oxidation of chromium +3 to chromium +6 was negligible at room temperature and only became significant in hot concentrated nitric acid. The rate of reduction of chromium +6 back to chromium +3 by reaction with stainless steel or oxalic acid was found to be much greater than the rate of the reverse oxidation reaction. Based on these findings and taking into account normal operating conditions, it was determined that although there would be considerable chromium in plutonium process streams it would rarely be found in the +6 oxidation state and would not exist in the +6 state in the final process waste solutions

Effect of low X-ray dose irradiation on properties triglycine sulfate doped by chromium

CERN Document Server

Kamysheva, L N; Golitsyna, O M

2002-01-01

One studied effect of X-ray low dose on pulse re-polarization in triglycine sulfate crystals (TGS) with various concentration of chromium ions. It is shown that within 20.0 deg C-T sub c temperature range alpha activation field values depend unambiguously on radiation dose for various polarity switching current pulses. One detected decrease of unipolarity of TGS crystal caused by chromium ions due to interaction of radiation defects with impurity ones

The electrochemistry of chromium, chromium-boron and chromium-phosphorus alloys

International Nuclear Information System (INIS)

Moffat, T.P.; Ruf, R.R.; Latanision, R.M.

1987-01-01

It is fairly well established that chromium-metalloid interactions represent the key to understanding the remarkable corrosion behavior of TM-Cr-M glasses; (Fe, Ni, Co,...)-Cr-(P, Si, C, S). The character and kinetics of passive film growth on the glasses are being studied ni order to assess the role of the film former, chromium, and the metalloids in the passivation process. A series of thin film microcrystalline chromium, Cr-B and Cr-P binary alloys have been fabricated by physical vapor deposition techniques. Vacuum melted conventionally processed chromium has also been studied. Examination of these materials in lM H/sub 2/SO/sub 4/ and lM HCl by voltammetry, potentiostatic and impedance techniques yields the following conclusion: 1. Pure chromium with a grain size varying from < 400 A to 0.5 mm exhibits no well defined differences in electrochemical behavior in lM H/sub 2/SO/sub 4/. 2. The tremendous corrosion resistance of Cr-B alloys has been confirmed. 3. The beneficial effects observed for boron alloyed with chromium may be considered surprising in view of the neutral/negative influence of alloying boron with iron, i.e. Fe/sub 80/B/sub 20/. 4. The interaction of the electrochemistry of the metalloid constituent with that of the transition base element determines the corrosion behavior. 5. Preliminary work with Cr-P alloys indicates that certain compositions exhibit promising properties - certain films were found to be intact after two days of immersion in concentrated HCl. Further work is in progress

Chromium in aqueous nitrate plutonium process streams: Corrosion of 316 stainless steel and chromium speciation

International Nuclear Information System (INIS)

Smith, W.H.; Purdy, G.

1994-01-01

According to the measurements made in this study, the only situation in which chromium (+6) could exist in a plutonium process solution is one in which a feed containing chromium is dissolved in a glass pot dissolver in high nitric acid concentration and at high temperature. But when the resulting feed is prepared for ion exchange, the chemical treatment reduces chromium to the +3 state. Any solution being processed through the evaporator will only contain chromium in the +3 state and any chromium salts remaining in the evaporator bottoms will be chromium +3 salts

Application of solar radiation for heating and preparation of warm water in an individual house

International Nuclear Information System (INIS)

Kozak, Tadeeusz; Majchrzycka, Anna

2009-01-01

The paper is aimed at analysis of application of the solar collectors array for preparing of warm water and space heating in an individual house. Keywords: application of solar radiation, preparation of warm water, heating

Design and performance of chromium mist generator

Directory of Open Access Journals (Sweden)

Tirgar Aram

2006-01-01

Full Text Available Chromium mist generator is an essential tool for conducting researches and making science-based recommendations to evaluate air pollution and its control systems. The purpose of this research was to design and construct a homogenous chromium mist generator and the study of some effective factors including sampling height and distances between samplers in side-by-side sampling on chromium mist sampling method. A mist generator was constructed, using a chromium electroplating bath in pilot scale. Concentration of CrO3 and sulfuric acid in plating solution was 125 g L-1 and 1.25 g L-1, respectively. In order to create permanent air sampling locations, a Plexiglas cylindrical chamber (75 cm height, 55 cm i.d was installed the bath overhead. Sixty holes were produced on the chamber in 3 rows (each 20. The distance between rows and holes was 15 and 7.5 cm, respectively. Homogeneity and effective factors were studied via side-by-side air sampling method. So, 48 clusters of samples were collected on polyvinyl chloride (PVC filters housed in sampling cassettes. Cassettes were located in 35, 50, and 65 cm above the solution surface with less than 7.5 and/or 7.5-15 cm distance between heads. All samples were analyzed according to the NIOSH method 7600. According to the ANOVA test, no significant differences were observed between different sampling locations in side-by-side sampling (P=0.82 and between sampling heights and different samplers distances (P=0.86 and 0.86, respectively. However, there were notable differences between means of coefficient of variations (CV in various heights and distances. It is concluded that the most chromium mist homogeneity could be obtained at height 50 cm from the bath solution surface and samplers distance of < 7.5 cm.

The levels of ionizing radiation under ecological conditions of dwelling houses and some suggestions for standardization of Poland

International Nuclear Information System (INIS)

Pensko, J.

1978-01-01

An analysis has been performed of the effect of naturally occuring radioactive elements in the soil at the site of houses, and of the effect of cosmic radiation and the radioactive contamination of building materials on the ionizing radiation dose to the inhabitants. The problem of biological effects of small doses encountered inside the dwelling houses had been discussed and some recommendations have been put forward concerning the limits for the concentrations of naturally ocurring radioactive elements in the materials used in constructing dwelling houses. (author)

Influence of chromium ions on the color center formation in crystals with garnet structure

International Nuclear Information System (INIS)

Ashurov, M.Kh.; Zharikov, E.V.; Laptev, V.V.

1985-01-01

The in fluence of chromium ions on the color center formation in crystals of yttrium-aluminium garnet, gadolinium-gallium garnet, gadolinium-scandium-gallium garnet, and yttrium-scandium-gallium garnet is studied. In addition to basic activator ions these crystals were coactivated also by chromium ions with two wide bands of fundamental absorption within the range of pump tube radiation with maximas close to 450 and 650 nm. The color centers for γ-irradiated samples were observed at 300 K by measuring the adsorption spectra within the 300-800 nm range. Temperature of destruction of the charge trapping sites was determined by the method of thermoluminescence measuring in the 100-500 K temperature range. Detection of recombination center luminescence was accomplished within the 200-1600 nm wavelength range. Chromium ions are found to hinder the formation of color centers as a result of γ-irradiation at room and higher temperatures within the wavelength range over 300 nm; i.e. Cr 3+ ions increase radiation resistance of all the investigated crystals

Chromium allergy

DEFF Research Database (Denmark)

Hansen, M B; Johansen, J D; Menné, Torkil

2003-01-01

Most studies investigating chromium allergy have been performed with Cr(VI). However, real exposure to chromium from leather products includes both Cr(III) and Cr(VI). We have determined and compared the minimum elicitation threshold (MET) concentration for Cr(III) and Cr(VI) in Cr(VI)-sensitive ......Most studies investigating chromium allergy have been performed with Cr(VI). However, real exposure to chromium from leather products includes both Cr(III) and Cr(VI). We have determined and compared the minimum elicitation threshold (MET) concentration for Cr(III) and Cr(VI) in Cr......(III) was concluded to play an important role in chromium allergy, because Cr(III) and Cr(VI) were both capable of eliciting eczema at low concentrations. Rather than regarding chromium dermatitis as a result of Cr(VI) allergy alone, it may be more correct to consider it as a result of a combined Cr(III) and Cr......(VI) allergy....

Determination of chromium combined with DNA, RNA and proteins in chromium-rich brewer's yeast by NAA

International Nuclear Information System (INIS)

Ding, W.J.; Qian, Q.F.; Hou, X.L.; Feng, W.Y.; Chai, Z.F.

2000-01-01

The content of chromium in the DNA, RNA and protein fractions separated from chromium-rich and normal brewer's yeast was determined by neutron activation analysis (NAA). Our results show that the extracted relative amounts and concentrations of DNA, RNA and proteins have no significant difference for two types of yeast, but the chromium content in DNA, RNA and proteins fractions extracted from the chromium-rich yeast are substantially higher than those from the normal. In addition, the concentration of chromium in DNA is much higher than that in RNA and proteins. It is evident that the inorganic chromium compounds can enter the yeast cell during the yeast cultivation in the chromium-containing culture medium and are converted into organic chromium species, which are combined with DNA, RNA and proteins. (author)

Intestinal absorption of chromium as affected by wheat bran

International Nuclear Information System (INIS)

Keim, K.S.; Holloway, C.L.; Hegsted, M.

1986-01-01

This study was designed to investigate the influence of dietary fiber, as found in wheat bran, on the absorption of chromium. Twenty male Sprague-Dawley rats were divided into two groups of 10. The control was fed a semi-purified diet containing casein, methionine, cornstarch, sucrose, corn oil, mineral and vitamin mix, and choline bitartrate. The experimental group was fed the same diet but with soft red winter wheat bran added to a level of 35% of the diet at the expense of sucrose. To determine chromium absorption and uptake by selected tissues, rats were fasted for 24 hr, fed 5 g of the respective diet, 2 hr later intubated with 100μCi of Cr-51of sacrificed 24 hr later. The rats wee housed in metabolic cages after the Cr-51 intubation. The addition of wheat brand to the diet did not significantly affect chromium absorption as measured by percent dose of Cr-51 in the 24 hr urine. The percent dose in the control group was 0.68 +/- 0.20% (mean +/- SEM) and in the experimental group 0.63 +/- 0.24% (mean +/-SEM) (N.S.). The cr-51 uptake of liver, spleen, jejunum, and blood was not statistically different between groups. These results indicate that dietary fiber as found in wheat bran does not impair intestinal absorption of chromium

Characteristics of chromium-allergic dermatitis patients prior to regulatory intervention for chromium in leather

DEFF Research Database (Denmark)

Bregnbak, David; Thyssen, Jacob P; Zachariae, Claus

2014-01-01

BACKGROUND: Chromium-tanned leather articles currently constitute the most important cause of contact allergy to chromium in Denmark. A regulation on the content of hexavalent chromium in leather was adopted in November 2013 by the EU member states. OBJECTIVES: To characterize patients...... with chromium allergy and their disease, to serve as a baseline for future studies on the potential effect of the new regulation on chromium in leather. METHODS: A questionnaire case-control study was performed on 155 dermatitis patients with positive patch test reactions to potassium dichromate and a matched...... control group of 621 dermatitis patients. Comparisons were made by use of a χ(2) -test and the Mann-Whitney U-test. Logistic regression analyses were used to test for associations. RESULTS: Sixty-six per cent of chromium-allergic patients had a positive history of contact dermatitis caused by leather...

Chromium

Science.gov (United States)

... 2 Whole wheat bread, 2 slices 2 Red wine, 5 ounces 1–13 Apple, unpeeled, 1 medium ... chromium or a placebo) might simply show the benefits of supplementation in a chromium-deficient population. Overall, ...

A possible effect of electromagnetic radiation from mobile phone base stations on the number of breeding house sparrows (Passer domesticus).

Science.gov (United States)

Everaert, Joris; Bauwens, Dirk

2007-01-01

A possible effect of long-term exposure to low-intensity electromagnetic radiation from mobile phone (GSM) base stations on the number of House Sparrows during the breeding season was studied in six residential districts in Belgium. We sampled 150 point locations within the 6 areas to examine small-scale geographic variation in the number of House Sparrow males and the strength of electromagnetic radiation from base stations. Spatial variation in the number of House Sparrow males was negatively and highly significantly related to the strength of electric fields from both the 900 and 1800 MHz downlink frequency bands and from the sum of these bands (Chi(2)-tests and AIC-criteria, Pnegative relationship was highly similar within each of the six study areas, despite differences among areas in both the number of birds and radiation levels. Thus, our data show that fewer House Sparrow males were seen at locations with relatively high electric field strength values of GSM base stations and therefore support the notion that long-term exposure to higher levels of radiation negatively affects the abundance or behavior of House Sparrows in the wild.

Simultaneous determination of chromium(III) and chromium(VI) in aqueous solutions by ion chromatography and chemiluminescence detection

DEFF Research Database (Denmark)

Gammelgaard, Bente; Jøns, O; Nielsen, B

1992-01-01

A method for the simultaneous determination of chromium(iii) and chromium(vi) in a flow system based on chemiluminescence was developed. A Dionex cation-exchange guard column was used to separate chromium(iii) from chromium(vi), and chromium(vi) was reduced by potassium sulfite, whereupon both...

Specification for corrosion-resisting chromium and chromium-nickel steel covered welding electrodes

International Nuclear Information System (INIS)

Anon.

1981-01-01

This specification prescribes requirements for covered corrosion-resisting chromium and chromium-nickel steel electrodes. These electrodes are normally used for shielded metal arc welding, and include those alloy steels designated as corrosion or heat-resisting chromium and chromium-nickel steels, in which chromium exceeds 4.0% and nickel does not exceed 50.0%

Specification for corrosion-resisting chromium and chromium-nickel steel covered welding electrodes

International Nuclear Information System (INIS)

Anon.

1981-01-01

This specification prescribes requirements for covered corrosion-resisting chromium and chromium-nickel steel electrodes. These electrodes are normally used for shielded metal arc welding, and include those alloy steels designated as corrosion or heat-resisting chromium and chromium-nickel steels, in which chromium exceeds 4.0 percent and nickel does not exceed 50.0 percent

Amendment in phosphorus levels moderate the chromium toxicity in Raphanus sativus L. as assayed by antioxidant enzymes activities.

Science.gov (United States)

Sayantan, D; Shardendu

2013-09-01

Chromium (Z=24), a d-block element, is a potent carcinogen, whereas phosphorus is an essential and limiting nutrient for the plant growth and development. This study undertakes the role of phosphorus in moderating the chromium toxicity in Raphanus sativus L., as both of them compete with each other during the uptake process. Two-factor complete randomized experiment (5 chromium × 5 phosphorus concentrations) was conducted for twenty eight days in green house. The individuals of R. sativus were grown in pots supplied with all essential nutrients. The toxic effects of chromium and the moderation of toxicity due to phosphorus amendment were determined as accumulation of chromium, nitrogen, phosphorus in root tissues and their effects were also examined in the changes in biomass, chlorophyll and antioxidant enzyme levels. Cr and N accumulation were almost doubled at the highest concentration of Cr supply, without any P amendment, whereas at the highest P concentration (125 mM), the accumulation was reduced to almost half. A significant reduction in toxic effects of Cr was determined as there was three-fold increase in total chlorophyll and biomass at the highest P amendment. Antioxidant enzymes like superoxide dismutase, catalase, peroxidase and lipid peroxidation were analyzed at various levels of Cr each amended with five levels of P. It was observed that at highest level of P amendment, the reduction percentage in toxicity was 33, 44, 39 and 44, correspondingly. Conclusively, the phosphorus amendment moderates the toxicity caused by the supplied chromium in R. sativus. This finding can be utilized to develop a novel technology for the amelioration of chromium stressed fields. Copyright © 2013 Elsevier Inc. All rights reserved.

Residual effects of chromium gettering on the outgassing behavior of a stainless steel vacuum vessel

International Nuclear Information System (INIS)

Simpkins, J.E.; Blanchard, W.R.; Dylla, H.F.; LaMarche, P.H.

1986-05-01

Laboratory experiments that compared chromium and titanium gettering showed that with chromium, unlike titanium, there is no appreciable diffusion of hydrogen isotopes into the film. It was concluded from these experiments that chromium gettering on tokamaks is more desirable than titanium gettering, since chromium should provide higher hydrogen recycling, minimize tritium inventories, and avoid hydrogen embrittlement. Large-scale sublimation sources, consisting of hollow elongated chromium spheres with internal resistance heaters, were developed for use on tokamaks. These sources have been used to getter both the Impurity Study Experiment (ISX) and the Tokamak Fusion Test Reactor (TFTR). In both bases, significant effects on plasma performance were observed, including lower Z/sub eff/ and radiated power losses and an increase in the density limit. In TFTR these effects were observed for a period of weeks after a single chromium deposition. This paper reports the results of laboratory experiments made to examine the gettering characteristics of chromium films under conditions simulating those in TFTR

Ultra low nanowear in novel chromium/amorphous chromium carbide nanocomposite films

Science.gov (United States)

Yate, Luis; Martínez-de-Olcoz, Leyre; Esteve, Joan; Lousa, Arturo

2017-10-01

In this work, we report the first observation of novel nanocomposite thin films consisting of nanocrystalline chromium embedded in an amorphous chromium carbide matrix (nc-Cr/a-CrC) with relatively high hardness (∼22,3 GPa) and ultra low nanowear. The films were deposited onto silicon substrates using a magnetic filtered cathodic arc deposition system at various negative bias voltages, from 50 to 450 V. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) suggested the co-existence of chromium and chromium carbide phases, while high resolution transmission electron microscopy (HRTEM) confirmed the presence of the nc-Cr/a-CrC structure. The friction coefficient measured with the ball-on disk technique and the nanowear results showed a strong correlation between the macro and nano-tribological properties of the samples. These novel nanocomposite films show promising properties as solid lubricant and wear resistant coatings with relatively high hardness, low friction coefficient and ultra low nanowear.

Roentgenoelectronic investigation into oxidation of iron-chromium and iron-chromium-nickel alloys

International Nuclear Information System (INIS)

Akimov, A.G.; Rozenfel'd, I.L.; Kazanskij, L.P.; Machavariani, G.V.

1978-01-01

Kinetics of iron-chromium and iron-chromium-nickel alloy oxidation (of the Kh13 and Kh18N10T steels) in oxygen was investigated using X-ray electron spectroscopy. It was found that according to X-ray electron spectra chromium oxidation kinetics in the iron-chromium alloy differs significantly from oxidation kinetics of chromium pattern. Layer by layer X-ray electron analysis showed that chromium is subjected to a deeper oxidation as compared to iron, and accordingly, Cr 2 O 3 layer with pure iron impregnations is placed between the layer of mixed oxide (Fe 3 O 4 +Cr 2 O 3 ) and metal. A model of the iron-chromium alloy surface is suggested. The mixed oxide composition on the steel surface is presented as spinel Fesub(2+x)Crsub(1-x)Osub(y)

Cadmium decontamination using in-house resin

International Nuclear Information System (INIS)

Pal, Sangita; Thalor, K.L; Prabhakar, S.; Srivastava, V.K.; Goswami, J.L.; Tewari, P.K.; Dhanpal, Pranav; Goswami, J.L.

2010-01-01

A selective and strong in-house chelator has been studied w.r.t. basic parameters like concentration, time, and elution. De-contamination of cadmium, mercury, chromium, lead etc by using high uptake values fro cadmium ions proves its selectivity with high elution ratio ensures further decontamination of run-off water during natural calamities. In three step cascade use the concentration of original cadmium solution (500 ppm) decocted to safe disposable attribute. This polymeric ligand exchanger displayed outlet effluent concentration to 1 ppm and less than 200 ppb when treated for inlet feed concentration of 50 ppm and 500 ppm respectively. (author)

Specification for corrosion-resisting chromium and chromium-nickel steel covered welding electrodes

International Nuclear Information System (INIS)

Anon.

1983-01-01

This specification prescribes requirements for covered corrosion-resisting chromium and chromium-nickel steel electrodes. These electrodes normally are used for shielded metal arc welding, and include those alloy steels designated as corrosion or heat-resisting chromium-nickel steels in which chromium exceeds 4.0 percent and nickel does not exceed 50.0 percent

Practical sublimation source for large-scale chromium gettering in fusion devices

Energy Technology Data Exchange (ETDEWEB)

Simpkins, J E; Gabbard, W A; Emerson, L C; Mioduszewski, P K [Oak Ridge National Lab., TN (USA)

1984-05-01

This paper describe the fabrication and testing of a large-scale chromium sublimation source that resembles the VARIAN Ti-ballsup(TM) in its design. The device consists of a hollow chromium sphere with a diameter of approximately 3 cm and an incandescent filament for radiation heating from inside the ball. We also discuss the gettering technique utilizing this source. The experimental arrangement consists of an ultrahigh vacuum (UHV) system instrumented for total and partial pressure measurements, a film thickness monitor, thermocouples, an optical pyrometer, and appropriate instrumentation to measure the heating power. The results show the temperature and corresponding sublimation rate of the Cr-ball as functions of input power. In addition, an example of the total pumping speed of a gettered surface is shown.

Canadian House Dust Study: Population-based concentrations, loads and loading rates of arsenic, cadmium, chromium, copper, nickel, lead, and zinc inside urban homes

Energy Technology Data Exchange (ETDEWEB)

Rasmussen, Pat E. [Exposure and Biomonitoring Division, Healthy Environments and Consumer Safety Branch, Health Canada, 50 Colombine Driveway, Ottawa, ON, Canada K1A 0K9 (Canada); Department of Earth Sciences, University of Ottawa, 140 Louis Pasteur, Ottawa, ON, Canada K1N 6N5 (Canada); Levesque, Christine [Exposure and Biomonitoring Division, Healthy Environments and Consumer Safety Branch, Health Canada, 50 Colombine Driveway, Ottawa, ON, Canada K1A 0K9 (Canada); Chénier, Marc; Gardner, H. David [Exposure and Biomonitoring Division, Healthy Environments and Consumer Safety Branch, Health Canada, 50 Colombine Driveway, Ottawa, ON, Canada K1A 0K9 (Canada); Department of Earth Sciences, University of Ottawa, 140 Louis Pasteur, Ottawa, ON, Canada K1N 6N5 (Canada); Jones-Otazo, Heather [Regions and Programs Branch, Health Canada, 180 Queen Street West, Toronto, ON, Canada M5V 3L7 (Canada); Petrovic, Sanya [Contaminated Sites Division, Healthy Environments and Consumer Safety Branch, Health Canada, 269 Laurier Ave West, Ottawa, ON, Canada K1A 0K9 (Canada)

2013-01-15

The Canadian House Dust Study was designed to obtain nationally representative urban house dust metal concentrations (μg g{sup −1}) and metal loadings (μg m{sup −2}) for arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni), lead (Pb), and zinc (Zn). Consistent sampling of active dust of known age and provenance (area sampled) also permitted the calculation of indoor loading rates (mg m{sup −2} day{sup −1} for dust and μg m{sup −2} day{sup −1} for metals) for the winter season (from 2007 to 2010) when houses are most tightly sealed. Geomean/median indoor dust loading rates in homes located more than 2 km away from industry of any kind (9.6/9.1 mg m{sup −2} day{sup −1}; n = 580) were significantly lower (p < .001) than geomean (median) dust loading rates in homes located within 2 km of industry (13.5/13.4 mg m{sup −2} day{sup −1}; n = 421). Proximity to industry was characterized by higher indoor metal loading rates (p < .003), but no difference in dust metal concentrations (.29 ≥ p ≤ .97). Comparisons of non-smokers' and smokers' homes in non-industrial zones showed higher metal loading rates (.005 ≥ p ≤ .038) in smokers' homes, but no difference in dust metal concentrations (.15 ≥ p ≤ .97). Relationships between house age and dust metal concentrations were significant for Pb, Cd and Zn (p < .001) but not for the other four metals (.14 ≥ p ≤ .87). All seven metals, however, displayed a significant increase in metal loading rates with house age (p < .001) due to the influence of higher dust loading rates in older homes (p < .001). Relationships between three measures of metals in house dust – concentration, load, and loading rate – in the context of house age, smoking behavior and urban setting consistently show that concentration data is a useful indicator of the presence of metal sources in the home, whereas dust mass is the overriding influence on metal loadings and loading rates

Sorption of chromium(III) and chromium(VI) on lead sulfide

International Nuclear Information System (INIS)

Music, S.

1985-01-01

The sorption of chromium(III) and chromium(VI) on lead sulfide was investigated in dependence on pH, time of sorption, and on the concnetrations of sorbate and sorbent. The mechanisms of the sorption of Crsup(3+) and CrOsub(4)sup(2-) traces on lead sulfide are discussed; a difference between CrOsub(4)sup(2-) sorption on PbS and α-Fesub(2)Osub(3) was found. Sulfates and molybdates affect the removal of chromates from aqueous solutions. Lead sulfide carrier prepared in this work was also used for the preconcentration of chromium(III) and chromium(VI) from tap water. (author)

Calculated electronic structure of chromium surfaces and chromium monolayers on iron

International Nuclear Information System (INIS)

Victora, R.H.; Falicov, L.M.

1985-01-01

A self-consistent calculation of the magnetic and electronic properties of the chromium (100) and (110) surfaces and of a chromium monolayer on the (100) and (110) iron surfaces is presented. It is found that (i) the (100) chromium surface is ferromagnetic with a greatly enhanced spin polarization (3.00 electrons); (ii) a substantial enhancement of the spin imbalance exists several (>5) layers into the bulk; (iii) the (110) chromium surface is antiferromagnetic with a large (2.31) spin imbalance; (iv) the (100) chromium monolayer on ferromagnetic iron is ferromagnetic, with a huge spin imbalance (3.63), and aligned antiferromagnetically with respect to the bulk iron; (v) the (110) chromium monolayer on ferromagnetic iron is also ferromagnetic, with a spin imbalance of 2.25 and antiferromagnetically aligned to the iron. The spin imbalance of chromium on iron (100) is possibly the largest of any transition-metal system

Performance analysis on natural energy autonomous house, HARBEMAN house; Shizen energy jiritsu house (HARBEMAN house) no simulation ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujino, T; Saito, T [Tohoku University, Sendai (Japan)

1997-11-25

Outlined herein are a procedure developed to simulate performance of an energy-autonomous (independent) solar house referred to as HARBEMAN HOUSE (HH) built in 1996 in City of Sendai, comparison between the simulated and observed results, and characteristics of the solar house. The house is equipped with a solar collector and sky radiator, both installed on the roof, the former facing south to collect solar energy and generate hot water whereas the latter facing north to radiate heat and generate cool water. Both are connected to an underground heat-insulated tank having a capacity of 31m{sup 3}, which stores hot or cool water to keep their conditions for extended periods. The solar system operates in heat- or cool-storage mode. In the heat-storage mode, quantity of heat stored increases, although at a slow rate, as tank capacity increases. In the cool-storage mode, on the other hand, quantity of cool stored increases in proportion to tank capacity. This is because solar energy is collected throughout the year whereas cooling by radiation is concentrated in early spring. Loss rate of heat stored increases as tank capacity increases, and the opposite trend is observed with cool stored. 12 refs., 7 figs., 2 tabs.

The suppression of dissolution for alloy 690 in high temperature and high pressure water with chromium ion implantation

International Nuclear Information System (INIS)

Shibata, Toshio; Fujimoto, Shinji; Ohtani, Saburou; Watanabe, Masanori; Hirao, Kyozo; Okumoto, Masaru; Shibaike, Hiroyuki.

1994-01-01

As the material of heat exchanger tubes for PWRs, the nickel alloys such as alloy 690 and alloy 600 have been used, but 58 Ni and 60 Co contained as an impurity elute in primary cooling water, and are radioactivated, in this way, they become the cause of radiation exposure. By increasing chromium concentration, the corrosion resistance of nickel alloys is improved, and for modern heat exchangers, the alloy 690, of which the chromium content is increased up to 30%, has been adopted, and excellent results have been obtained. In this research, aiming at the further reduction of radiation exposure, by increasing the chromium concentration in surface layer using ion implantation technology, the change of the corrosion behavior of alloy 690 in high temperature, high pressure water was investigated. The chemical composition of the alloy 690 used, and the making of plate specimens are shown. The polarization behavior of alloy 690 in 0.1 mol/l sulfuric acid deaerated at normal temperature is reported, and the effect of suppressing dissolution was remarkable in the specimens with much implantation. The electrochemical behavior of alloy 690 in simulated cooling water was investigated. Immobile case has high chromium content and is thin. (K.I.)

Efficient Separation and Extraction of Vanadium and Chromium in High Chromium Vanadium Slag by Selective Two-Stage Roasting-Leaching

Science.gov (United States)

Wen, Jing; Jiang, Tao; Xu, Yingzhe; Liu, Jiayi; Xue, Xiangxin

2018-04-01

Vanadium and chromium are important rare metals, leading to a focus on high chromium vanadium slag (HCVS) as a potential raw material to extract vanadium and chromium in China. In this work, a novel method based on selective two-stage roasting-leaching was proposed to separate and extract vanadium and chromium efficiently in HCVS. XRD, FT-IR, and SEM were utilized to analyze the phase evolutions and microstructure during the whole process. Calcification roasting, which can calcify vanadium selectively using thermodynamics, was carried out in the first roasting stage to transfer vanadium into acid-soluble vanadate and leave chromium in the leaching residue as (Fe0.6Cr0.4)2O3 after H2SO4 leaching. When HCVS and CaO were mixed in the molar ratio CaO/V2O3 (n(CaO)/n(V2O3)) of 0.5 to 1.25, around 90 pct vanadium and less than 1 pct chromium were extracted in the first leaching liquid, thus achieving the separation of vanadium and chromium. In the second roasting stage, sodium salt, which combines with chromium easily, was added to the first leaching residue to extract chromium and 95.16 pct chromium was extracted under the optimal conditions. The total vanadium and chromium leaching rates were above 95 pct, achieving the efficient separation and extraction of vanadium and chromium. The established method provides a new technique to separate vanadium and chromium during roasting rather than in the liquid form, which is useful for the comprehensive application of HCVS.

Efficient Separation and Extraction of Vanadium and Chromium in High Chromium Vanadium Slag by Selective Two-Stage Roasting-Leaching

Science.gov (United States)

Wen, Jing; Jiang, Tao; Xu, Yingzhe; Liu, Jiayi; Xue, Xiangxin

2018-06-01

Vanadium and chromium are important rare metals, leading to a focus on high chromium vanadium slag (HCVS) as a potential raw material to extract vanadium and chromium in China. In this work, a novel method based on selective two-stage roasting-leaching was proposed to separate and extract vanadium and chromium efficiently in HCVS. XRD, FT-IR, and SEM were utilized to analyze the phase evolutions and microstructure during the whole process. Calcification roasting, which can calcify vanadium selectively using thermodynamics, was carried out in the first roasting stage to transfer vanadium into acid-soluble vanadate and leave chromium in the leaching residue as (Fe0.6Cr0.4)2O3 after H2SO4 leaching. When HCVS and CaO were mixed in the molar ratio CaO/V2O3 (n(CaO)/n(V2O3)) of 0.5 to 1.25, around 90 pct vanadium and less than 1 pct chromium were extracted in the first leaching liquid, thus achieving the separation of vanadium and chromium. In the second roasting stage, sodium salt, which combines with chromium easily, was added to the first leaching residue to extract chromium and 95.16 pct chromium was extracted under the optimal conditions. The total vanadium and chromium leaching rates were above 95 pct, achieving the efficient separation and extraction of vanadium and chromium. The established method provides a new technique to separate vanadium and chromium during roasting rather than in the liquid form, which is useful for the comprehensive application of HCVS.

Development of low-chromium, chromium-tungsten steels for fusion

International Nuclear Information System (INIS)

Klueh, R.L.; Alexander, D.J.; Kenik, E.A.

1995-01-01

High-chromium (9-12% Cr) Cr-Mo and Cr-W ferritic steels are favored as candidates for fusion applications. In early work to develop reduced-activation steels, an Fe-2.25Cr-2W-0.25V-0.1C steel (designated 2.25Cr-2WV) had better strength than an Fe-9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa) steel (compositions are in weight percent). However, the 2.25Cr-2WV had poor impact properties, as determined by the ductile-brittle transition temperature and upper-shelf energy of subsize Charpy impact specimens. Because low-chromium steels have some advantages over high-chromium steels, a program to develop low-chromium steels is in progress. Microstructural analysis indicated that the reason for the inferior impact toughness of the 2.25Cr-2WV was the granular bainite obtained when the steel was normalized. Properties can be improved by developing an acicular bainite microstructure by increasing the cooling rate after austenitization. Alternatively, acicular bainite can be promoted by increasing the hardenability. Hardenability was changed by adding small amounts of boron and additional chromium to the 2.25Cr-2WV composition. A combination of B, Cr, and Ta additions resulted in low-chromium reduced-activation steels with mechanical properties comparable to those of 9Cr-2WVTa. (orig.)

Reproductive toxicological aspects of chromium in males

International Nuclear Information System (INIS)

Ernst, E.

1994-01-01

To expand our present understanding of the effects of chromium on male fertility a number of studies were designed to achieve this through the use of chromium intoxicated experimental animals and through investigation of sexual hormones and sperm quality in welders. Also in view of the lack of an experimental model for effects of noxious substance on the epididymal spermatozoa the main objectives of the series of studies reviewed here were: A. To establish a model for evaluation of epididymal sperm count and motility in the rat. B. To investigate and compare the effects of tri- and hexavalent chromium on epididymal spermatozoa. Further to describe the effects of low-dose long-time exposure of rats to the most toxicological interesting chromium oxidative state - hexavalent chromium. C. By the use of autoradiography and γ-countinuing to expand the present knowledge on the distribution of chromium in the body with special reference to the male reproductive organs. D. To describe the effects of exposure to hexavalent chromium in welding fume on levels of sexual hormones and semen parameters in welders. (EG)

Practical sublimation source for large-scale chromium gettering in fusion devices

International Nuclear Information System (INIS)

Simpkins, J.E.; Emerson, L.C.; Mioduszewski, P.K.

1983-01-01

This paper describes the technique of chromium gettering with a large-scale sublimation source which resembles in its design the VARIAN Ti-Ball. It consists of a hollow chromium sphere with a diameter of approximately 3 cm and an incandescent filament for radiation heating from inside the ball. While the fabrication of the source is described in a companion paper, we discuss here the gettering technique. The experimental arrangement consists of an UHV system instrumented for total- and partial-pressure measurements, a film-thickness monitor, thermocouples, an optical pyrometer, and appropriate instrumentation to measure the heating power. The results show the temperature and corresponding sublimation rate of the Cr-Ball as function of input power. In addition, an example of the total pumping speed of a gettered surface is shown

Responses of endogenous proline in rice seedlings under chromium exposure

Directory of Open Access Journals (Sweden)

X.Z. Yu

2016-12-01

Full Text Available Hydroponic experiments were performed to exam the dynamic change of endogenous proline in rice seedlings exposed to potassium chromate chromium (VI or chromium nitrate chromium (III. Although accumulation of both chromium species in rice seedlings was obvious, more chromium was detected in plant tissues of rice seedlings exposed to chromium (III than those in chromium (VI, majority being in roots rather than shoots. Results also showed that the accumulation capacity of chromium by rice seedlings was positively correlated to chromium concentrations supplied in both chromium variants and the accumulation curve depicted an exponential trend in both chromium treatments over the entire period of exposure. Proline assays showed that both chromium variants induced the change of endogenous proline in shoots and roots of rice seedlings. Chromium (VI of 12.8 mg/L increased proline content significantly (p

Chromium in potatoes

International Nuclear Information System (INIS)

Stoddard-Gilbert, K.; Blincoe, C.

1989-01-01

Chromium concentration in potatoes was determined, and tubes were labeled either intrinsically or extrinsically with radioactive chromate ( 51 Cr). A labeled chromium complex was isolated from preparations of raw, baked, or fried potatoes and chromatographed on gel permeation media. Potato pulp and peel contained 1.63 and 2.70 μg of Cr/g tissue, respectively. There was no correlation between the two, nor did they respond similarly to changes of variety or locations. No significant differences were apparent in relative migration of the isolated complexes except between raw and cooked extrinsically labeled preparations

A practical sublimation source for large-scale chromium gettering in fusion devices

International Nuclear Information System (INIS)

Simpkins, J.E.; Gabbard, W.A.; Emerson, L.C.; Mioduszewski, P.K.

1984-01-01

This paper describe the fabrication and testing of a large-scale chromium sublimation source that resembles the VARIAN Ti-ballsup(TM) in its design. The device consists of a hollow chromium sphere with a diameter of approximately 3 cm and an incandescent filament for radiation heating from inside the ball. We also discuss the gettering technique utilizing this source. The experimental arrangement consists of an ultrahigh vacuum (UHV) system instrumented for total and partial pressure measurements, a film thickness monitor, thermocouples, an optical pyrometer, and appropriate instrumentation to measure the heating power. The results show the temperature and corresponding sublimation rate of the Cr-ball as functions of input power. In addition, an example of the total pumping speed of a gettered surface is shown. (orig.)

Leaching of chromium from chromium contaminated soil: Speciation study and geochemical modeling

Directory of Open Access Journals (Sweden)

Anđelković Darko H.

2012-01-01

Full Text Available Distribution of chromium between soil and leachate was monitored. A natural process of percolating rainwater through the soil was simulated in the laboratory conditions and studied with column leaching extraction. Migration of chromium in the soil is conditioned by the level of chromium soil contamination, the soil organic matter content, and rainwater acidity. Chromium (III and chromium(VI were determined by spectrophotometric method with diphenilcarbazide in acidic media. Comparing the results of chromium speciation in leachate obtained by experimental model systems and geochemical modelling calculations using Visual MINTEQ model, a correlation was observed regarding the influence of the tested parameters. Leachate solutions showed that the concentration of Cr depended on the organic matter content. The influence of pH and soil organic matter content is in compliance after its definition through experimental and theoretical way. The computer model - Stockholm Humic Model used to evaluate the leaching results corresponded rather well with the measured values.

Nasal manifestations in chromium industry workers.

Science.gov (United States)

Aiyer, R G; Kumar, Gaurav

2003-04-01

People working in mines, plating factories, cement industries are mainly exposed to chrome substances, IIexavalent chromium has been implicated for its toxic effect on the nasal mucosa. Hereby we present a rare study of 28 patients who attended out patient department of Otorhinolaryngology at SSG Hospital, Baroda from a nearby chromium industry. This study aims to present various nasal manifestations of toxic effects of prolonged chromium exposure.

Heterogeneous chromium catalysts

NARCIS (Netherlands)

2005-01-01

The present invention relates to a heterogeneous chromium catalyst system for the polymerisation of ethylene and/or alpha olefins prepared by the steps of: (a) providing a silica-containing support, (b) treating the silica-containing support with a chromium compound to form a chromium-based

Permeation of chromium salts through human skin in vitro

DEFF Research Database (Denmark)

Gammelgaard, Bente; Fullerton, A; Avnstorp, C

1992-01-01

Chromium permeation studies were performed on full thickness human skin in diffusion cells. All samples were analysed for the total chromium content by graphite furnace Zeeman-corrected atomic absorption spectrometry. Some samples were analysed by an ion chromatographic method permitting...... the simultaneous determination of Cr(VI) and Cr(III) as well. The amounts of chromium found in all skin layers were significantly higher when potassium dichromate was applied to the skin compared with chromium chloride or chromium nitrate. Chromium could only be detected in the recipient phase after application...... of the dichromate solution. Chromium skin levels increased with increasing concentrations of applied chromium salts up to 0.034 M Cr. The amount of chromium in recipient phase and skin layers increased with increasing pH when the applied solution contained potassium dichromate. This was ascribed to a decreased skin...

Quantitative determination of chromium in some vegetables in ...

African Journals Online (AJOL)

Chromium has been known to be a micronutrient for mammals for more than four decades. Deficiency in the body results to diabetes, infertility and cardiovascular diseases. However, progress in elucidating the role of chromium has proceeded slowly. Recent studies have shown a potential role of chromium in maintaining ...

Replacing critical radiators to increase the potential to use low-temperature district heating – A case study of 4 Danish single-family houses from the 1930s

International Nuclear Information System (INIS)

Østergaard, Dorte Skaarup; Svendsen, Svend

2016-01-01

Low-temperature district heating is a promising technology for providing homes with energy-efficient heating in the future. However, it is of great importance to maintain thermal comfort in existing buildings when district heating temperatures are lowered. This case study evaluated the actual radiator sizes and heating demands in 4 existing Danish single-family houses from the 1930s. A year-long dynamic simulation was performed for each of the houses to evaluate the potential to lower the heating system temperatures. The results indicate that there is a large potential to use low-temperature district heating in existing single-family houses. In order to obtain the full potential of low-temperature district heating, critical radiators must be replaced. Based on a novel method, a total of nine radiators were identified to be critical to ensure thermal comfort and low return temperatures in two of the case-houses. If these radiators were replaced it would be possible to lower the average heating system temperatures to 50 °C/27 °C in all four houses. - Highlights: • Comparison of dynamically calculated heat demands and radiator sizes. • Method for identification and evaluation of critical radiators was tested. • Existing houses can be heated with low-temperature heating for most of the year. • Replacing critical radiators helps ensure comfort and low return temperatures.

Carcinogenicity and mutagenicity of chromium.

Science.gov (United States)

Léonard, A; Lauwerys, R R

1980-11-01

Occupational exposure represents the main source of human contamination by chromium. For non-occupationally exposed people the major environmental exposure to chromium occurs as a consequence of its presence in food. Chromium must be considered as an essential element. Its deficiency impairs glucose metabolism. Trivalent chromium salts are poorly absorbed through the gastro-intestinal and respiratory tracts because they do not cross membranes easily. Hexavalent chromium can be absorbed by the oral and pulmonary routes and probably also through the skin. After its absorption, hexavalent chromium is rapidly reduced to the trivalent form which is probably the only form to be found in biological material. Epidemiological studies have shown that some chromium salts (mainly the slightly soluble hexavalent salts) are carcinogens. Lung cancers have, indeed, often been reported among workers in chromate-producing industry and, to a lesser extent, in workers from the chrome-pigment industry. The first attempts to produce cancers in experimental animals by inhalation or parenteral introduction gave negative or equivocal results but, from 1960, positive results have been obtained with various chromium compounds. As for the carcinogenic activity, the mutagenicity of chromium has mainly been found with hexavalent salts. In the majority of assay systems used, trivalent chromium appears inactive. It can be considered as evident, however, that the ultimate mutagen which binds to the genetic material is the trivalent form produced intracellularly from hexavalent chromium, the apparent lack of activity of the trivalent form being due to its poor cellular uptake.

Chromium fate in constructed wetlands treating tannery wastewaters.

Science.gov (United States)

Dotro, Gabriela; Palazolo, Paul; Larsen, Daniel

2009-06-01

Nine experimental wetlands were built to determine chromium partitioning inside systems treating tannery wastewaters. Results showed 5-day biochemical oxygen demand and chromium removals of 95 to 99% and 90 to 99%, respectively. The majority of chromium was found in association with media (96 to 98%), followed by effluents (2.9 to 3.9%), and the least was found in plant parts (0.1%). Chemical speciation modeling of solutions and scanning electron microscope analysis suggest two potential chromium removal mechanisms--sorption/coprecipitation with iron hydroxides or oxyhydroxides and biomass sorption. The release of the majority of chromium in the iron- and organic-bound phases during sequential extractions supports the proposed dominant removal mechanisms. The use of a mixture of peat and gravel resulted in lower removal efficiencies and stronger partitioning in organic phases during sequential extractions. Chromium was efficiently removed by wetlands, retained through chemical and biological processes. Future research will focus on further exploring removal mechanisms and proposing management strategies for the chromium-containing wetland media.

Citric-acid preacidification enhanced electrokinetic remediation for removal of chromium from chromium-residue-contaminated soil.

Science.gov (United States)

Meng, Fansheng; Xue, Hao; Wang, Yeyao; Zheng, Binghui; Wang, Juling

2018-02-01

Electrokinetic experiments were conducted on chromium-residue-contaminated soils collected from a chemical plant in China. Acidification-electrokinetic remediation technology was proposed in order to solve the problem of removing inefficient with ordinary electrokinetic. The results showed that electrokinetic remediation removal efficiency of chromium from chromium-contaminated soil was significantly enhanced with acidizing pretreatment. The total chromium [Cr(T)] and hexavalent chromium [Cr(VI)] removal rate of the group acidized by citric acid (0.9 mol/L) for 5 days was increased from 6.23% and 19.01% in the acid-free experiments to 26.97% and 77.66% in the acidification-treated experiments, respectively. In addition, part of chromium with the state of carbonate-combined will be converted into water-soluble state through acidification to improve the removal efficiency. Within the appropriate concentration range, the higher concentration of acid was, the more chromium was released. So the removal efficiency of chromium depended on the acid concentration. The citric acid is also a kind of complexing agent, which produced complexation with Cr that was released by the electrokinetic treatment and then enhanced the removal efficiency. The major speciation of chromium that was removed from soils by acidification-electrokinetics remediation was acid-soluble speciation, revivification speciation and oxidation speciation, which reduced biological availability of chromium.

Discussion about the range of natural radiation exposure rate found in dwelling-houses in the Federal Republic of Germany and in Poland

International Nuclear Information System (INIS)

Schmier, H.; Pensko, J.; Wicke, A.

1982-01-01

In this paper the range of natural radiation exposure rate found in dwelling-houses is discussed. The source of this exposure are natural radionuclides 40 K, 226 Ra, 232 Th and their decay products widely distributed in soil and in building materials. The resulting whole body dose equivalent rate of gamma radiation is compared to the effective dose equivalent rate of alpha radiation originating from 222 Rn diffusing out of building materials and decaying to alpha emitting short living daughters. (Author) [de

Chromium carcinogenicity: California strategies.

Science.gov (United States)

Alexeeff, G V; Satin, K; Painter, P; Zeise, L; Popejoy, C; Murchison, G

1989-10-01

Hexavalent chromium was identified by California as a toxic air contaminant (TAC) in January 1986. The California Department of Health Services (CDHS) concurred with the findings of the International Agency for Research on Cancer that there is sufficient evidence to demonstrate the carcinogenicity of chromium in both animals and humans. CDHS did not find any compelling evidence demonstrating the existence of a threshold with respect to chromium carcinogenesis. Experimental data was judged inadequate to assess potential human reproductive risks from ambient exposures. Other health effects were not expected to occur at ambient levels. The theoretically increased lifetime carcinogenic risk from a continuous lifetime exposure to hexavalent chromium fell within the range 12-146 cancer cases per nanogram hexavalent chromium per cubic meter of air per million people exposed, depending on the potency estimate used. The primary sources found to contribute significantly to the risk of exposure were chrome platers, chromic acid anodizing facilities and cooling towers utilizing hexavalent chromium as a corrosion inhibitor. Evaluation of genotoxicity data, animal studies and epidemiological studies indicates that further consideration should be given to the potential carcinogenicity of hexavalent chromium via the oral route.

Structure of a fatty acid-binding protein from Bacillus subtilis determined by sulfur-SAD phasing using in-house chromium radiation

DEFF Research Database (Denmark)

Nan, Jie; Zhou, Yanfeng; Yang, Cheng

2009-01-01

Sulfur single-wavelength anomalous dispersion (S-SAD) and halide-soaking methods are increasingly being used for ab initio phasing. With the introduction of in-house Cr X-ray sources, these methods benefit from the enhanced anomalous scattering of S and halide atoms, respectively. Here...... electron-density map was obtained after density modification. The model of BsDegV was built automatically and a palmitate was found tightly bound in the active site. Sequence alignment and comparisons with other known DegV structures provided further insight into the specificity of fatty-acid selection...

Chromium getter studies in TFTR

International Nuclear Information System (INIS)

Dylla, H.F.; LaMarche, P.H.; Blanchard, W.R.

1986-02-01

We have studied the effects of the deposition of thin films (approx.0.1 μm) of chromium onto approx.70% of the torus area of the Tokamak Fusion Test Reactor (TFTR). The purpose of these experiments was to test the difference between high surface coverage and high pumping speed gettering schemes with respect to minimizing oxygen impurity generation in high power tokamak discharges. The initial Cr deposition had significant effects on vessel outgassing and subsequent plasma performance: the outgassing of H 2 O, CO, and CO 2 decreased by a factor of ten, oxygen impurity radiation decreased by a factor of two, the plasma Z/sub eff/ decreased from 1.3 to 1.1, and the plasma density limit increased by 20%. This improvement correlates with a significant reduction of the edge radiation as the density limit is approached. The effects of the initial and subsequent Cr depositions were relatively long lasting, exhibiting time constants of the order of weeks. We attribute the observed impurity reduction to a modification of the oxide surface on the vessel wall, which is apparently a significant impurity source for oxygen. 17 refs., 6 figs

Low energy housing in Ticino - The 'Vitali-Velti' house

Energy Technology Data Exchange (ETDEWEB)

Pahud, D.; Generelli, M. [SUPSI-DCT/LEEE-UREC, Trevano-Canobbio (Switzerland); Velti, A; Vitali, B. [architetto, Monte Carasso (Switzerland)

2003-02-15

This final report for the Swiss Federal Office of Energy (SFOE) takes a look at work done concerning low energy consumption housing in southern Switzerland. Thanks to large windows in the south-east facade and a well insulated building envelope, the passive solar gains are quoted as providing significant contributions to heating. The remaining heating requirements are covered by a closed fireplace and an electric radiator. Heat is distributed by free convection inside the house, A double-flux ventilation system with heat recovery ensures air renewal (3 volumes per day). Each house has a solar hot water system with electric auxiliary energy supply. Space heating requirements are discussed and compared with the standard values as defined in Swiss energy standards and the conventional auxiliary space heating energy required for the houses is noted.

Effect of carbon and silicon on nitrogen solubility in liquid chromium and iron-chromium alloys

International Nuclear Information System (INIS)

Khyakkinen, V.I.; Bezobrazov, S.V.

1986-01-01

The study is aimed at specifying the role of carbon and silicon in high-chromium melts nitridation processes. It is shown that in high-chromium melts of the Cr-Fe-C system the nitrogen solubility is reduced with the growth of carbon content and in the chromium concentration range of 70-100% at 1873 K and P N 2 =0.1 MPa it is described by the lg[%N] Cr-Fe-C =lg[%N] cr-fe -0.098[%C] equation. While decreasing the temperature the nitrogen solubility in alloys is increased. Silicon essentially decreases the nitrogen solubility in liquid chromium. For the 0-10% silicon concentration range the relation between the equilibrium content of nitrogen and silicon at 1873 K and P N 2 =0.1 MPa is described by the straight line equation [%N] Cr-Si =6.1-0.338 [%Si

Hexavalent and trivalent chromium in leather: What should be done?

Science.gov (United States)

Moretto, Angelo

2015-11-01

Trivalent chromium compounds are used for leather tanning, and chromium may be released during use of leather goods. In certain instances, small amounts of hexavalent chromium can be formed and released. Both trivalent and hexavalent chromium can elicit allergic skin reaction in chromium sensitised subjects, the latter being significantly more potent. Induction of sensitisation only occurs after exposure to hexavalent chromium. A minority of subjects are sensitised to chromium, and in a fraction of these subjects allergic skin reaction have been described after wearing leather shoes or, less frequently, other leather goods. The evidence that in all these cases the reaction is related to hexavalent chromium is not always strong. The content of hexavalent chromium in leather is regulated in European Union, but rate of release rather than content is relevant for allergic skin reaction. The role of trivalent chromium appear much less relevant if at all. Modern tanning procedure do not pose significant risk due to either hexavalent or trivalent chromium. Dismissing bad quality and worn-off leather goods is relevant in reducing or eliminating the skin reaction. It should also be pointed out that shoe components or substances other than chromium in leather may cause allergic/irritative skin reactions. Copyright © 2015 Elsevier Inc. All rights reserved.

Hexavalent Chromium Minimization Strategy

Science.gov (United States)

2011-05-01

Logistics 4 Initiative - DoD Hexavalent Chromium Minimization Non- Chrome Primer IIEXAVAJ ENT CHRO:M I~UMI CHROMIUM (VII Oil CrfVli.J CANCEfl HAnRD CD...Management Office of the Secretary of Defense Hexavalent Chromium Minimization Strategy Report Documentation Page Form ApprovedOMB No. 0704-0188...00-2011 4. TITLE AND SUBTITLE Hexavalent Chromium Minimization Strategy 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6

Lipid peroxidation in workers exposed to hexavalent chromium.

Science.gov (United States)

Huang, Y L; Chen, C Y; Sheu, J Y; Chuang, I C; Pan, J H; Lin, T H

1999-02-26

The aim of this study was to investigate whether exposure to hexavalent chromium induces lipid peroxidation in human. This study involved 25 chrome-plating factory workers and a reference group of 28 control subjects. The whole-blood and urinary chromium concentrations were determined by graphite furnace atomic absorption spectrophotometry. Malondialdehyde (MDA), the product of lipid peroxidation, was determined by high-performance liquid chromatography, and the activities of protective enzymes were measured by ultraviolet-visible spectrophotometry. In the chrome-plating workers, the mean concentrations of chromium in blood and urine were 5.98 microg/L and 5.25 microg/g creatinine, respectively; the mean concentrations of MDA in blood and urine were 1.7 micromol/L and 2.24 micromol/g creatinine. The concentrations of both chromium and MDA in blood and urine were significantly higher in the chromium-exposed workers. The activities of superoxide dismutase (SOD), glutathione peroxidase (GPX), and catalase (CAT) were not markedly different between control and exposed workers. Data suggest that MDA may be used as a biomarker for occupational chromium exposure. Antioxidant enzymic activities are not a suitable marker for chromium exposure.

Specification for corrosion-resisting chromium and chromium-nickel steel welding rods and bare electrodes - approved 1969

International Nuclear Information System (INIS)

Anon.

1975-01-01

This specification covers corrosion-resisting chromium and chromium-nickel steel welding rods for use with the atomic hydrogen and gas-tungsten-arc welding processes and bare electrodes for use with the submerged arc and gas metal-arc welding processes. These welding rods and electrodes include those alloy steels designated as corrosion- or heat-resisting chromium and chromium-nickel steels, in which chromium exceeds 4% and nickel does not exceed 50%

Uptake and transport of chromium in plants

International Nuclear Information System (INIS)

Ramachandran, V.; D'souza, T.J.; Mistry, K.B.

1980-01-01

The uptake of chromium, an important soil and water pollutant, by five different plant species was examined in nutrient culture experiments using chromium-51 as a tracer. The concentration in aerial tissues of both trivalent and hexavalent forms of chromium was the greatest in peas followed by beans, tomato and the cereals over identical uptake periods. The uptake of 51 Cr 3+ was, in general, greater than 51 CrO 4 2- . Studies with bean plants indicated that shoot uptake of both forms of chromium decreased with increasing pH and salt concentration of the external solution. Concentrations of 10 -4 M and 10 -5 M DNP inhibited 51 Cr uptake by bean shoots. (author)

The Chromium is an essential element in the human

International Nuclear Information System (INIS)

Alvarado Gamez, A.; Blanco Saenz, R.; Mora Morales, E.

2002-01-01

The Chromium is an essential element for human and animals, because it a preponderant function in the insulin metabolism as a glucose tolerance factor (GTF). The deficiency of chromium engenders a deterioration in the glucose metabolism due to bad efficiency of insulin. Because the importance of this element an exhaustive reference review was made and this presents some studies realized in laboratory animals and in human beings where it is prove with resuits the effect of chromium over the improvement of patients with non-insulin dependant diabetes. Three substances are presented as chromium active biological forms: a material rich in chromium known as glucose tolerance factor, chromium picolinate and a substance of low molecular weight LMWCr in its forms of apo and holo that contains chromium and it links the insulin receptor and improves its activity. Also this paper presents information about the condition of diabetes in Costa Rica. (Author) [es

Serum chromium levels in gestational diabetes mellitus

Directory of Open Access Journals (Sweden)

P G Sundararaman

2012-01-01

Full Text Available Objective: To measure serum chromium level in women with gestational diabetes mellitus (GDM from Chennai, South India. Materials and Methods: Thirty women with gestational diabetes, 60 age matched controls. Inclusion criteria: Gestational age 22-28 weeks, age group 20-35 years. Exclusion Criteria: Gestational age beyond 28 weeks, malnutrition or presence of infection. Serum chromium was measured using inductive couple plasma emission spectrometer. Results: Serum chromium levels of women with GDM, 1.59+/-0.02 ng/ml (range: 0.16-4.0 ng/ml were lower than in controls (4.58+/-0.62 ng/ml; range 0.82-5.33 ng/ml (P < 0.001. However, there were no significant differences among cases and controls when subdivided by parity. Conclusions: Women with GDM from a South Indian city had lower levels of serum chromium compared to pregnant women without GDM. Studies may be done whether chromium supplementation is useful in this group of women.

Breeding biology of Tree Swallows and House Wrens in a gradient of gamma radiation

International Nuclear Information System (INIS)

Zach, R.; Mayoh, K.R.

1982-01-01

In a gradient of gamma radiation from 38.7 mC kg - 1 .d - 1 to background levels of 0.05 μC. kg - 1 . d - 1 to background levels of 0.05 μC . kg - 1 . d - 1 , Tree Swallows (Iridoprocne bicolor) and House Wrens (Troglodytes aedon) avoided nesting in areas of high radiation. Nest boxes selected by swallows and wrens had a mean exposure rate of only 9.3 and 6.6 μC . kg - 1 . d - 1 , respectively. Lateral and canopy vegetation indices and nest hole height and direction could not explain the observed pattern of box selection. Of the boxes with low exposure rates, swallows selected those with little vegetation cover, whereas wrens chose boxes and heavy cover. It appears that the birds responded to radiation levels as low as 100 times background, but it is not clear whether they actually detected radiation or simply responded to secondary clues. The number of swallows and wrens fledged per box was unrelated to radiation exposure. The same was true for number of eggs, hatching success, fledging success, incubation time, and nestling time. Breeding success was reduced because of infertile eggs, eggs with dead embryos, cracked eggs, predation, adverse weather, abandonment, and parasites. The logistic model was ideally suited for describing gains in mass in nestling swallows and wrens. Growth of nestlings was not related to radiation exposure as indicated by the growth rate constant, asymptotic mass, and the proportion of variation explained by the logistic model. Breeding and growth performance were similar in studies not involving experimental radiation

Hexavalent Chromium Compounds

Science.gov (United States)

Learn about chromium, exposure to which can increase your risk of lung cancer and cancer of the paranasal sinuses and nasal cavity. Hexavalent chromium compounds have been used as corrosion inhibitors in a wide variety of products and processes.

Establishment of a reference value for chromium in the blood for biological monitoring among occupational chromium workers.

Science.gov (United States)

Li, Ping; Li, Yang; Zhang, Ji; Yu, Shan-Fa; Wang, Zhi-Liang; Jia, Guang

2016-10-01

The concentration of chromium in the blood (CrB) has been confirmed as a biomarker for occupational chromium exposure, but its biological exposure indices (BEIs) are still unclear, so we collected data from the years 2006 and 2008 (Shandong Province, China) to analyze the relationship between the concentration of chromium in the air (CrA) of the workplaces and CrB to establish a reference value of CrB for biological monitoring of occupational workers. The levels of the indicators for nasal injury, kidney (β2 microglobulin (β2-MG)), and genetic damages (8-hydroxy-deoxyguanosine (8-OHdG) and micronucleus (MN)) were measured in all subjects of the year 2011 (Henan Province, China) to verify the protective effect in this reference value of CrB. Compared with the control groups, the concentrations of CrA and CrB in chromium exposed groups were significantly higher (P value of CrB was recommended to 20 μg/L. The levels of nasal injury, β2-MG, 8-OhdG, and MN were not significantly different between the low chromium exposed group (CrB ≤ 20 μg/L) and the control group, while the levels of β2-MG, 8-OHdG, and MN were statistically different in the high chromium exposed group than that in the control group. This research proved that only in occupational workers, CrB could be used as a biomarker to show chromium exposure in the environment. The recommended reference value of CrB was 20 μg/L. © The Author(s) 2015.

Experimental patch testing with chromium-coated materials.

Science.gov (United States)

Bregnbak, David; Thyssen, Jacob P; Jellesen, Morten S; Zachariae, Claus; Johansen, Jeanne D

2017-06-01

Chromium coatings on metal alloys can be decorative, and prevent corrosion and metal ion release. We recently showed that handling of a chromium-containing disc resulted in chromium deposition on the skin. To examine patch test reactivity to chromium-coated discs. We included 15 patients: 10 chromium-allergic patients, and 5 patients without chromium allergy. All were patch tested with potassium dichromate, cobalt chloride, nickel sulfate, and nine different metallic discs. The chromium-allergic patients were also patch tested with serial dilutions of potassium dichromate. Positive/weaker reactions were observed to disc B (1 of 10), disc C (1 of 10), and disc D, disc E, and disc I (4 of 10 each). As no controls reacted to any of the discs, the weak reactions indicate allergic reactions. Positive patch test reactions to 1770 ppm chromium(VI) in the serial dilutions of potassium dichromate were observed in 7 of 10 patients. When the case group was narrowed down to include only the patients with a current positive patch test reaction to potassium dichromate, elicitation of dermatitis by both chromium(III) and chromium(VI) discs was observed in 4 of 7 of patients. Many of the patients reacted to both chromium(III) and chromium(VI) surfaces. Our results indicate that both chromium(VI) and chromium(III) pose a risk to chromium-allergic patients. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Femtosecond laser surface structuring and oxidation of chromium thin coatings: Black chromium

Energy Technology Data Exchange (ETDEWEB)

Kotsedi, L., E-mail: Kotsedi@tlabs.ac.za [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Nuru, Z.Y. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Mthunzi, P. [National Laser Centre, Council for Scientific and Industrial Research, 0001 Pretoria (South Africa); Muller, T.F.G. [University of the Western Cape, Physics Department, Bellville, 7535 Cape Town (South Africa); Eaton, S.M. [Physics Department, Politecnico di Milano, Piazza Leonardo Da Vinci, 32, 20133 Milano (Italy); Julies, B. [University of the Western Cape, Physics Department, Bellville, 7535 Cape Town (South Africa); Manikandan, E. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Ramponi, R. [Physics Department, Politecnico di Milano, Piazza Leonardo Da Vinci, 32, 20133 Milano (Italy); Maaza, M. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa)

2014-12-01

Highlights: • Oxidation of the chromium thin film to chromium oxide by femtosecond laser with a fundamental wavelength of 1064 nm. • Solar absorber from chromium oxide that low percentage reflectance. • Femtosecond laser oxidation, with a de-focused laser. • Chromium oxide formation by femtosecond laser in normal ambient. - Abstract: In view of their potential applications as selective solar absorbers, chromium coatings on float glass substrates were nano/micro structured by femtosecond laser in air. Raman and X-rays diffraction investigations confirmed the formation of an ultra-porous α-Cr{sub 2}O{sub 3} layer at the surface; higher is the input laser power, enhanced is the crystallinity of the α-Cr{sub 2}O{sub 3} layer. The α-Cr{sub 2}O{sub 3} layer with the Cr underneath it in addition to the photo-induced porosity acted as a classical ceramic–metal nano-composite making the reflectance to decrease significantly within the spectral range of 190–1100 nm. The average reflectance decreased from 70 to 2%.

Chemical Speciation of Chromium in Drilling Muds

International Nuclear Information System (INIS)

Taguchi, Takeyoshi; Yoshii, Mitsuru; Shinoda, Kohzo

2007-01-01

Drilling muds are made of bentonite and other clays, and/or polymers, mixed with water to the desired viscosity. Without the drilling muds, corporations could not drill for oil and gas and we would have hardly any of the fuels and lubricants considered essential for modern industrial civilization. There are hundreds of drilling muds used and some kinds of drilling muds contain chromium. The chemical states of chromium in muds have been studied carefully due to concerns about the environmental influence. However it is difficult to determine the chemical state of chromium in drilling muds directly by conventional analytical methods. We have studied the chemical form of chromium in drilling muds by using a laboratory XAFS system and a synchrotron facility

Treatment of chromium contaminated soil using bioremediation

Science.gov (United States)

Purwanti, Ipung Fitri; Putri, Tesya Paramita; Kurniawan, Setyo Budi

2017-11-01

Chromium contamination in soil occurs due to the disposal of chromium industrial wastewater or sludge that excess the quality standard. Chromium concentration in soil is ranged between 1 to 300 mg/kg while the maximum health standard is 2.5 mg/kg. Bioremediation is one of technology that could be used for remediating heavy metal contamination in soil. Bacteria have an ability to remove heavy metal from soil. One bacteria species that capable to remove chromium from soil is Bacillus subtilis. The aim of this research was to know the chromium removal percentage in contaminated soil by Bacillus subtilis. Artificial chromium contaminated soil was used by mixing 425gram sand and chromium trichloride solution. Concentration of chromium added into the spiked soil were 50, 75, and 100 mg/L. During 14 days, pH, soil temperature and soil moisture were tested. Initial and final number of bacterial colony and chromium concentration analysed. The result showed that the highest percentage of chromium removal was 11% at a chromium concentration of 75 mg/L

The chromium accumulation and its physiological effects in juvenile rockfish, Sebastes schlegelii, exposed to different levels of dietary chromium (Cr(6+)) concentrations.

Science.gov (United States)

Kim, Jun-Hwan; Kang, Ju-Chan

2016-01-01

Juvenile rockfish (mean length 13.7±1.7 cm, and mean weight 55.6±4.8 g) were exposed for 4 weeks with the different levels of dietary chromium (Cr(6+)) at 0, 30, 60, 120 and 240 mg/kg. The profile of chromium in the tissues of rockfish is dependent on the exposure periods and chromium concentration. After 4 weeks, the order of chromium accumulation in tissues was liver>kidney>spleen>intestine>gill>muscle. The dietary chromium exposure decreased the growth rate and hepatosomatic index of rockfish. The major hematological findings were significant decrease in the red blood cell (RBC) count, hematocrit (Ht) value, and hemoglobin (Hb) concentration exposed to ≥120 mg/kg chromium concentrations. The dietary chromium exposure (≥120 mg/kg) led to notable increase in glucose, cholesterol, glutamic oxalate transaminase (GOT), and glutamic pyruvate transaminase (GPT) in plasma, whereas there was no considerable change in calcium, magnesium, total protein, and alkaline phosphatase (ALP). The results indicated that the dietary chromium exposure to rockfish can induce significant chromium accumulation in the specific tissues, inhibition of growth, and hematological alterations. Copyright © 2015 Elsevier B.V. All rights reserved.

Separation of valence forms of chromium(III) and chromium(VI) by coprecipitation with iron(III) hydroxide

International Nuclear Information System (INIS)

Nazirmadov, B.; Khamidov, B.O.; Egorova, L.A.

1989-01-01

The sorption of 9.62·10 -5 M of Cr (III) and Cr (VI) with iron hydroxide in 1 M potassium nitrate and potassium chloride was investigated in relation to the pH of the medium. Experimental data on the sorption of chromium(III) and chromium(VI) with iron(III) hydroxide made it possible to determine the region of practically complete concentration of Cr (III) and Cr (VI) (pH = 3-6.5). The results from spectrophotometric investigations, calculated data on the distribution of the hydroxocationic forms of chromium(III) and the anions of chromium(IV), and their sorption by iron-(III) hydroxide made it possible to characterize the sorbability of the cationic and anionic forms of chromium in various degrees of oxidation. On this basis a method was developed for the separation of chromium(III) and chromium(VI) by coprecipitation on iron(III) hydroxide and their separation from the iron(III) hydroxide support

Experimental patch testing with chromium-coated materials

DEFF Research Database (Denmark)

Bregnbak, David; Thyssen, Jacob P; Jellesen, Morten Stendahl

2017-01-01

Chromium coatings on metal alloys can be decorative, and prevent corrosion and metal ion release. We recently showed that handling of a chromium-containing disc resulted in chromium deposition on the skin. To examine patch test reactivity to chromium-coated discs. We included 15 patients: 10...... chromium-allergic patients, and 5 patients without chromium allergy. All were patch tested with potassium dichromate, cobalt chloride, nickel sulfate, and nine different metallic discs. The chromium-allergic patients were also patch tested with serial dilutions of potassium dichromate. Positive...

Increased chromium uptake in polymorphonuclear leukocytes from burned patients

International Nuclear Information System (INIS)

Davis, J.M.; Illner, H.; Dineen, P.

1984-01-01

Following thermal injury neutrophil function is severely impaired and thought to be hypometabolic; however, the host is considered to be hypermetabolic. To further investigate the metabolism and the function of neutrophils following thermal injury, neutrophil migration and chromium uptake were studied using radio-labelled neutrophils. Random and directed migration were found to be significantly reduced compared to control values. Neutrophil lysozyme content was also reduced in these burn cells while serum lysozyme from the same patients was significantly elevated over control values. These data suggest lysozyme is released by the neutrophil into the circulatory system. The influx of chromium in cells from burned patients was much greater than the influx in normal cells used in studies for chemotaxis. Influx of chromium over time and over varying concentrations of chromium was linear in cells from burned patients and normals. Cells from burned patients, however, took up more chromium than normals. Influx velocity of chromium was also determined and found to be greater in burn cells than normal cells. Since it has been shown that chromium influx is an energy-dependent reaction it is suggested that cellular energy stores are being depleted by the influx of chromium. Whether this is a response to an intracellular deficit or uncoupling of metabolic pathways is not known at this time

Replacing critical radiators to increase the potential to use low-temperature district heating – A case study of 4 Danish single-family houses from the 1930s

DEFF Research Database (Denmark)

Østergaard, Dorte Skaarup; Svendsen, Svend

2016-01-01

radiator sizes and heating demands in 4 existing Danish single-family houses from the 1930s. A year-long dynamic simulation was performed for each of the houses to evaluate the potential to lower the heating system temperatures. The results indicate that there is a large potential to use low......-temperature district heating in existing single-family houses. In order to obtain the full potential of low-temperature district heating, critical radiators must be replaced. Based on a novel method, a total of nine radiators were identified to be critical to ensure thermal comfort and low return temperatures in two...

Breeding biology of tree swallows and house wrens in a gradient of gamma radiation

International Nuclear Information System (INIS)

Zach, R.; Mayoh, K.R.

1982-01-01

In a gradient of gamma radiation ranging from 38.7 mC.kg -1 .d -1 to background levels of 0.05 μC.kg -1 .d -1 , Tree Swallows (Iridoprocne bicolor) and House Wrens (Troglodytes aedon) avoided nesting in areas of high radiation. Nest boxes selected by swallows and wrens had a mean exposure rate of only 9.3 and 6.6 μC.kg -1 .d -1 , respectively. Lateral and canopy vegetation indices and nest hole height and direction could not explain the observed pattern of box selection. Of the boxes with low exposure rates, swallows selected those with little vegetation cover, whereas wrens chose boxes with heavy cover. It appears that the birds responded to radiaton levels as low as 100 times background but it is not clear whether they actually detected radiation or simply responded to secondary clues. The number of swallows and wrens fledged per box was unrelated to radiation exposure. The same was true for number of eggs, hatching success, fledging success, incubation time, and nestling time. Breeding success was reduced because of infertile eggs, eggs with dead embryos, cracked eggs, predation, adverse weather, abandonment, and parasites. The logistic model was ideally suited for describing gains in mass in nestling swallows and wrens. Growth of nestlings was not related to radiation exposure as indicated by the growth rate constant, asymptotic mass, and the proportion of variation explained by the logistic model. The data show that birds avoided adverse effects of radiation by judicious box selection. However, there were indications that at higher breeding densities birds may use high-exposure boxes, where breeding success or growth of nestlings may become reduced due to radiation

Determination of chromium in treated crayfish, Procambarus clarkii, by electrothermal ASS: study of chromium accumulation in different tissues

Energy Technology Data Exchange (ETDEWEB)

Hernandez, F.; Diaz, J.; Medina, J.; Del Ramo, J.; Pastor, A.

1986-06-01

In the present study, the authors investigated the accumulation of chromium in muscle, hepatopancreas, antennal glands, and gills of Procambarus clarkii (Girard) from Lake Albufera following Cr(VI)-exposure. Determinations of chromium were made by using Electrothermal Atomic Absorption Spectroscopy and the standard additions method.

Diminishing Chromium Use on Combined Chromium-Gambier Tanning Process Upon the Characteristics of Tanned Leather

Directory of Open Access Journals (Sweden)

A. Kasim

2014-04-01

Full Text Available The research was aimed to investigate the influence of minimizing chromium use on combined chromium-gambier process upon the characteristics of tanned leather. At the first stage of tanning process, chromium was used and in the second stage it was replaced by gambier. The raw material used was dried saline-preserved goat skin. The treatments applied on the tanning process were the different concentrations of chromium ranging from the highest level of 6% to the lowest level of 1% which was then re-tanned by using 8% concentration of gambier. The examination parameters included chemical and physical properties as well as visual investigation on the tanned leather in accordance with SNI-06-0463-1989-A. The result showed that the tanning process by using 2% chromium in the first step and 8% gambier in the second step was a treatment combination producing tanned leather that met the standard. The examination on tanned leather resulted from such treatment showed 56.33% rawhide, 17.45% of bound tannin, 31.22% of tanning level, tensile strength 386.30 kg/cm2, flexibility 31.91%, leather width 1.3 mm, density 0.75 g/cm3, the leather was quite elastic with light brownish color. In conclusion, minimizing the use of chromium in the combined tanning process of chromium and gambier can be implemented to the lowest of 2% chromium concentration and 8% gambier in the first and second step, respectively.

In situ removal of carbon contamination from a chromium-coated mirror: ideal optics to suppress higher-order harmonics in the carbon K-edge region.

Science.gov (United States)

Toyoshima, Akio; Kikuchi, Takashi; Tanaka, Hirokazu; Mase, Kazuhiko; Amemiya, Kenta

2015-11-01

Carbon-free chromium-coated optics are ideal in the carbon K-edge region (280-330 eV) because the reflectivity of first-order light is larger than that of gold-coated optics while the second-order harmonics (560-660 eV) are significantly suppressed by chromium L-edge and oxygen K-edge absorption. Here, chromium-, gold- and nickel-coated mirrors have been adopted in the vacuum ultraviolet and soft X-ray branch beamline BL-13B at the Photon Factory in Tsukuba, Japan. Carbon contamination on the chromium-coated mirror was almost completely removed by exposure to oxygen at a pressure of 8 × 10(-2) Pa for 1 h under irradiation of non-monochromated synchrotron radiation. The pressure in the chamber recovered to the order of 10(-7) Pa within a few hours. The reflectivity of the chromium-coated mirror of the second-order harmonics in the carbon K-edge region (560-660 eV) was found to be a factor of 0.1-0.48 smaller than that of the gold-coated mirror.

Determination of chromium in biological matrices by neutron activation

International Nuclear Information System (INIS)

McClendon, L.T.

1978-01-01

Chromium is recognized to be an essential trace element in several biological systems. It exists in many biological materials in a variety of chemical forms and very low concentration levels which cause problems for many analytical techniques. Both instrumental and destructive neutron activation analysis were used to determine the chromium concentration in Orchard Leaves, SRM 1571, Brewers Yeast, SRM 1569, and Bovine Liver, SRM 1577. Some of the problems inherent with determining chromium in certain biological matrices and the data obtained here at the National Bureau of Standards using this technique are discussed. The results obtained from dissolution of brewers yeast in a closed system as described in the DNAA procedure are in good agreement with the INAA results. The same phenomenon existed in the determination of chromium in bovine liver. The radiochemical procedure described for chromium (DNAA) provides the analyst with a simple, rapid and selective technique for chromium determination in a variety of matrices. (T.G.)

Reaction of Oxygen with Chromium and Chromium Carbide at Low O2 Pressures and High Temperatures

International Nuclear Information System (INIS)

Hur, Dong O.; Kang, Sung G.; Paik, Young N.

1984-01-01

The oxidation rate of chromium carbide has been measured continuously using thermogravimetric analysis at different oxygen pressures ranging from 1.33x10 -2 to 2.67x10 -1 Pa O 2 at 1000-1300 .deg. C. The oxidation of pure chromium has also been studied between 1000-1300 .deg. C under 6.67x10 -2 Pa O 2 and compared with that of chromium carbide. The oxidation of chromium carbide showed a linear behavior which was different from that of chromium. The oxidation rate of chromium carbide increased with increasing temperature and oxygen pressure was lower than of pure chromium. Above 1200 .deg. C, the volatile oxide was formed and evaporated causing a weight loss. The compositions and morphology of the oxide were studied with X-ray diffractometer and scanning electron microscope, respectively. The morphology of oxide changed with varying temperature and pressure. The oxide scale was consisted of mainly two different layers of Cr 2 O 3 and CrO, and the properties of oxide scale were correlated with oxidation behavior. The oxide film formed in the above test condition has been detached from the carbide surface. The crack and pore were thought to be from CO gas evolving at the interface of chromium carbide and its oxide and the major factor of the linear behavior of chromium carbide

Positron and nanoindentation study of helium implanted high chromium ODS steels

Science.gov (United States)

Veternikova, Jana Simeg; Fides, Martin; Degmova, Jarmila; Sojak, Stanislav; Petriska, Martin; Slugen, Vladimir

2017-12-01

Three oxide dispersion strengthened (ODS) steels with different chromium content (MA 956, MA 957 and ODM 751) were studied as candidate materials for new nuclear reactors in term of their radiation stability. The radiation damage was experimentally simulated by helium ion implantation with energy of ions up to 500 keV. The study was focused on surface and sub-surface structural change due to the ion implantation observed by mostly non-destructive techniques: positron annihilation lifetime spectroscopy and nanoindentation. The applied techniques demonstrated the best radiation stability of the steel ODM 751. Blistering effect occurred due to high implantation dose (mostly in MA 956) was studied in details.

Mode of occurrence of chromium in four US coals

Science.gov (United States)

Huggins, Frank E.; Shah, N.; Huffman, G.P.; Kolker, A.; Crowley, S.; Palmer, C.A.; Finkelman, R.B.

2000-01-01

The mode of occurrence of chromium in three US bituminous coals and one US subbituminous has been examined using both X-ray absorption fine structure (XAFS) spectroscopy and a selective leaching protocol supplemented by scanning electron microscopy (SEM) and electron microprobe measurements. A synthesis of results from both methods indicates that chromium occurs principally in two forms in the bituminous coals: the major occurrence of chromium is associated with the macerals and is not readily leached by any reagent, whereas a second, lesser occurrence, which is leachable in hydrofluoric acid (HF), is associated with the clay mineral, illite. The former occurrence is believed to be a small particle oxyhydroxide phase (CrO(OH)). One coal also contained a small fraction (<5%) of the chromium in the form of a chromian magnetite, and the leaching protocol indicated the possibility of a similar small fraction of chromium in sulfide form in all three coals. There was little agreement between the two techniques on the mode of occurrence of chromium in the subbituminous coal; however, only a limited number of subbituminous coals have been analyzed by either technique. The chromium in all four coals was trivalent as no evidence was found for the Cr6+ oxidation state in any coal.

Chromium-induced skin damage among Taiwanese cement workers.

Science.gov (United States)

Chou, Tzu-Chieh; Wang, Po-Chih; Wu, Jyun-De; Sheu, Shiann-Cherng

2016-10-01

Little research has been done on the relationships between chromium exposure, skin barrier function, and other hygienic habits in cement workers. Our purpose was to investigate chromium-induced skin barrier disruption due to cement exposure among cement workers. One hundred and eight cement workers were recruited in this study. Urinary chromium concentration was used to characterize exposure levels. The biological exposure index was used to separate high and low chromium exposure. Transepidermal water loss (TEWL) was used to assess the skin barrier function. TEWL was significantly increased in workers with high chromium exposure levels than those with low chromium exposure levels (p = 0.048). A positive correlation was also found between urinary chromium concentration and TEWL (R = 0.28, p = 0.004). After adjusting for smoking status and glove use, a significant correlation between urinary chromium concentrations and TEWL remained. Moreover, workers who smoked and had a high chromium exposure had significantly increased TEWL compared to nonsmokers with low chromium exposure (p = 0.01). Skin barrier function of cement workers may have been disrupted by chromium in cement, and smoking might significantly enhance such skin barrier perturbation with chromium exposure. Decreased chromium skin exposure and smoking cessation should be encouraged at work. © The Author(s) 2015.

Stabilization and solidification of chromium-contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Cherne, C.A.; Thomson, B.M. [Univ. of New Mexico, Albuquerque, NM (United States). Civil Engineering Dept.; Conway, R. [Sandia National Labs., Albuquerque, NM (United States)

1997-11-01

Chromium-contaminated soil is a common environmental problem in the United States as a result of numerous industrial processes involving chromium. Hexavalent chromium [Cr(VI)] is the species of most concern because of its toxicity and mobility in groundwater. One method of diminishing the environmental impact of chromium is to reduce it to a trivalent oxidation state [Cr(III)], in which it is relatively insoluble and nontoxic. This study investigated a stabilization and solidification process to minimize the chromium concentration in the Toxicity Characteristic Leaching Procedure (TCLP) extract and to produce a solidified waste form with a compressive strength in the range of 150 to 300 pounds per square inch (psi). To minimize the chromium in the TCLP extract, the chromium had to be reduced to the trivalent oxidation state. The average used in this study was an alluvium contaminated with chromic and sulfuric acid solutions. The chromium concentration in the in the in situ soil was 1212 milligrams per kilogram (mg/kg) total chromium and 275 mg/kg Cr(VI). The effectiveness of iron, ferrous sulfate to reduce Cr(VI) was tested in batch experiments.

Stabilization and solidification of chromium-contaminated soil

International Nuclear Information System (INIS)

Cherne, C.A.; Thomson, B.M.

1997-11-01

Chromium-contaminated soil is a common environmental problem in the United States as a result of numerous industrial processes involving chromium. Hexavalent chromium [Cr(VI)] is the species of most concern because of its toxicity and mobility in groundwater. One method of diminishing the environmental impact of chromium is to reduce it to a trivalent oxidation state [Cr(III)], in which it is relatively insoluble and nontoxic. This study investigated a stabilization and solidification process to minimize the chromium concentration in the Toxicity Characteristic Leaching Procedure (TCLP) extract and to produce a solidified waste form with a compressive strength in the range of 150 to 300 pounds per square inch (psi). To minimize the chromium in the TCLP extract, the chromium had to be reduced to the trivalent oxidation state. The average used in this study was an alluvium contaminated with chromic and sulfuric acid solutions. The chromium concentration in the in the in situ soil was 1212 milligrams per kilogram (mg/kg) total chromium and 275 mg/kg Cr(VI). The effectiveness of iron, ferrous sulfate to reduce Cr(VI) was tested in batch experiments

Chromium fractionation and speciation in natural waters.

Science.gov (United States)

Pereira, Catarinie Diniz; Techy, João Gabriel; Ganzarolli, Edgard Moreira; Quináia, Sueli Pércio

2012-05-01

It is common for leather industries to dump chromium-contaminated effluent into rivers and other bodies of water. Thus, it is crucial to know the impacts caused by this practice to the environment. A study on chromium partitioning and speciation, with determination at trace levels, was carried out in a potentially contaminated creek. Chromium fractionation and speciation was performed using a flow-injection preconcentration system and detection by flame atomic absorption spectrometry. High levels of this element were found in the particulate material (449-9320 mg kg(-1)), which indicates its compatibility with this fraction. The concentration of Cr(iii) in the water samples collected ranged from 5.2-105.2 μg L(-1). Cr(vi) was always below of the DL (0.3 μg L(-1)). Chromium accumulation observed in the sediment (873-1691 mg kg(-1)) may confirm contamination due to the long term release of contaminated effluents in the creek.

[Hexavalent chromium pollution and exposure level in electroplating workplace].

Science.gov (United States)

Zhang, Xu-hui; Zhang, Xuan; Yang, Zhang-ping; Jiang, Cai-xia; Ren, Xiao-bin; Wang, Qiang; Zhu, Yi-min

2012-08-01

To investigate the pollution of hexavalent chromium in the electroplating workplace and screen the biomarkers of chromium exposure. Field occupational health investigation was conducted in 25 electroplating workplaces. 157 electroplating workers and 93 healthy unexposed controls were recruited. The epidemiological information was collected with face to face interview. Chromium in erythrocytes was determined by graphite furnace atomic absorption spectrophotometer. The median of short-term exposure concentration of chromium in the air at electroplating workplace was 0.06 mg/m(3) (median) and ranging from 0.01 (detect limit) to 0.53 mg/m(3)). The median concentration of Cr (VI) in erythrocytes in electroplating workers was 4.41 (2.50 ∼ 5.29) µg/L, which was significantly higher than that in control subjects [1.54 (0.61 ∼ 2.98) µg/L, P electroplating workers and control subjects, except for the subjects of age less than 30 years old (P = 0.11). There was hexavalent chromium pollution in electroplating workplace. Occupational hazards prevention measures should be taken to control the chromium pollution hazards.

Reduction of hexavalent chromium collected on PVC filters.

Science.gov (United States)

Shin, Y C; Paik, N W

2000-01-01

Chromium exists at various valences, including elemental, trivalent, and hexavalent chromium, and undergoes reduction-oxidation reactions in the environment. Since hexavalent chromium is known as a human carcinogen, it is most important to evaluate the oxidation-reduction characteristics of the hexavalent chromium species. Although hexavalent chromium can be reduced to trivalent state, the detailed information on this in workplace environments is limited. The purpose of this study was to investigate hexavalent chromium reduction in time in various conditions. A pilot chrome plating operation was prepared and operated in a laboratory for this study. There was evidence that the hexavalent chromium was reduced by time after mist generation. The percentage ratio (with 95% confidence intervals in parentheses) of hexavalent chromium to total chromium was almost 100% (99.1 approximately 102.3) immediately after mist generation, and was reduced to 87.4% (84.8 approximately 89.9) at 1 hour and 81.0% (78.3 approximately 83.5) at 2 hours, respectively. Another test indicated that hexavalent chromium collected on PVC filters was also reduced by time after sampling. Hexavalent chromium was reduced to 90.8% (88.2 approximately 93.3) at 2 hours after sampling. It also was found that hexavalent chromium was reduced during storage in air. It is recommended that air samples of hexavalent chromium be protected against reduction during storage.

Separation of valent forms of chromium (3) and chromium (6) by coprecipitation with iron (3) hydroxide

International Nuclear Information System (INIS)

Nazirmadov, B.; Khamidov, B.O.; Egorova, L.A.

1988-01-01

Soption 9.62x10 -5 mol/l of 51 Cr radioactive isotope in oxidation states 3 and 6 by iron(3) hydroxide in 1 mol/l of KNO 3 and KCl depending on pH medium is investigated. The region of practically total concentration of Cr(3) and Cr(6 + ) (pH=3-6.5) is determined. The results of spectrophotometric investigations, calculational data on distribution of hydroxocation forms of chromium (3) and of chromium (6) anions and sorption by iron (3) hydroxide permit to characterize sorption of chromium forms in different stages of oxidation. The methods of chromium (3) and chromium (6) separation by coprecipitation of iron (3) hydroxide and their precipitation from it is developed on the above foundation

Determination of tracer quantities of chromium in uranium

International Nuclear Information System (INIS)

Huart, A.

1959-01-01

A method is described for the photometric determination of chromium in uranium by absorbency at 540 mμ of the Cr(VI) diphenylcarbazide combination. After attack by nitric acid, the solution is made perchloric, and the chromium oxidised at the boiling point by permanganate. Excess oxidant is removed by hydrochloric acid. Study of operating conditions resulted in a method with an accuracy of ± 0,5 ppm for 0,5 to 15 ppm chromium in the metal. (author) [fr

Chromium speciation in rainwater: temporal variability and atmospheric deposition

Energy Technology Data Exchange (ETDEWEB)

Kieber, R.J.; Willey, J.D.; Zvalaren, S.D. [University of North Carolina at Wilmington, Wilmington, NC (United States). Dept. of Chemistry

2002-12-15

Chromium is released into the atmosphere by a variety of anthropogenic activities which include steel manufacturing, leather tanning, wood presentation and fossil fuel combustion. The concentrations of the various chromium species were determined in 89 rainwater samples collected in Wilmington, NC from October 1, 1999 to December 31, 2001. Volume weighted annual average concentrations of Cr{sub total}, particulate Cr, Cr(III)(aq), and Cr(VI)(aq) were 4.6, 2.2, 0.8 and 1.2 nM, respectively. There was distinct seasonal and diurnal variability in the concentrations of the various chromium species. Chromium emissions to the global atmosphere by both natural and anthropogenic sources are estimated to be 2.2 x 10{sup 9} mol/yr. Using rainwater concentration data along with other published rainwater Cr concentrations and an estimate for total global annual rain, the total global flux of chromium removed from the atmosphere via wet deposition is 2.1 x 10{sup 9} mol/yr. This represents complete removal of Cr and indicates that essentially all chromium released into the global atmosphere is removed via rain. About half this chromium is dissolved with roughly equal concentrations of toxic Cr(VI) and relatively harmless Cr(III) species. 48 refs., 4 figs., 3 tabs.

Microscopic analysis of the chromium content in the chromium-induced malignant and premalignant bronchial lesions of the rat

International Nuclear Information System (INIS)

Takahashi, Yuji; Kondo, Kazuya; Ishikawa, Sumiyo; Uchihara, Hiroshi; Fujino, Haruhiko; Sawada, Naruhiko; Miyoshi, Takanori; Sakiyama, Shoji; Izumi, Keisuke; Monden, Yasumasa

2005-01-01

Objective: Our previous studies demonstrated that the frequency of gene instability in lung cancer of chromate workers was very high, but the frequencies of the p53 and ras gene mutations were low. To clarify the carcinogenesis of chromate in the lung, we established a chromate-induced cancer model in the rat proximal airway and examined the relationship between chromium accumulations and the chromium-induced cancer and premalignant bronchial lesions of the rat. Methods: Fifteen male, bred, 12-week-old Jcl-Wister rats were used. A pellet of strontium chromate were inserted into the bronchus of the rats. The rats were sacrificed 9 months after the pellet was inserted. We pathologically examined the region of the bronchi to which the pellet was attached. We quantified the amount of chromium accumulation in the bronchial lesions using a microscopic X-ray fluorescence analyzer. Results: Of the 15 rats, 1 rat had a lesion of squamous cell carcinoma (SCC), 7 rats had carcinoma in situ (CIS) or dysplasia, 8 rats had squamous metaplasia, and 5 rats had goblet cell hyperplasia. The amounts of chromium accumulation in normal epithelium (n=24), goblet cell hyperplasia (n=14), squamous metaplasia (n=8), and dysplasia plus CIS plus SCC (n=9) were 500±1354, 713±1062, 941±1328, and 3511±4473 (mean±SD) counts/s/mA, respectively. The amount of chromium accumulation was significantly increased according to the progression of malignant change of the bronchial epithelium (Spearman's correlation coefficient by ranks, rs=0.454, P<0.01). Conclusions: The amount of chromium accumulation was significantly increased according to the progression of malignant change of the bronchial epithelium. Examining the genetic alterations of histologic changes in this model was helpful in elucidating the process of carcinogenesis of chromium in the lung

Substoichiometric extraction of chromium

International Nuclear Information System (INIS)

Shigematsu, T.; Kudo, K.

1980-01-01

Substoichiometric extraction of chromium with tetraphenylarsonium chloride (TPACl), tri-n-octylamine (TNOA), diethylammonium diethyldithiocarbamate (DDDC) and ammonium pyrrolidinedithiocarbamate (APDC) was examined in detail. Chromium can be extracted substoichiometrically in a pH range, which is 1.1-2.6 for the TPACl compound, 0.6-2.3 for the TNOA compound, 5.1-6.4 for the DDDC chelate and 3.9-4.9 for the APDC chelate. Chromium in high-purity calcium carbonate, Orchard Leaves (NBS SRM-1571) and Brewers Yeast (NBS SRM-1569) was determined by neutron activation analysis combined with substoichiometric extraction by DDDC and APDC. The values of 2.0+-0.02 ppm and 2.6+-0.2 ppm were obtained for Brewers Yeast and Orchard Leaves, respectively. These values were in good agreement with those reported by NBS. The reaction mechanism and the reaction ratio between hexavalent chromium and dithiocarbamate are also discussed. (author)

Roasting and leaching behaviors of vanadium and chromium in calcification roasting-acid leaching of high-chromium vanadium slag

Science.gov (United States)

Wen, Jing; Jiang, Tao; Zhou, Mi; Gao, Hui-yang; Liu, Jia-yi; Xue, Xiang-xin

2018-05-01

Calcification roasting-acid leaching of high-chromium vanadium slag (HCVS) was conducted to elucidate the roasting and leaching behaviors of vanadium and chromium. The effects of the purity of CaO, molar ratio between CaO and V2O5 ( n(CaO)/ n(V2O5)), roasting temperature, holding time, and the heating rate used in the oxidation-calcification processes were investigated. The roasting process and mechanism were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), and thermogravimetry-differential scanning calorimetry (TG-DSC). The results show that most of vanadium reacted with CaO to generate calcium vanadates and transferred into the leaching liquid, whereas almost all of the chromium remained in the leaching residue in the form of (Fe0.6Cr0.4)2O3. Variation trends of the vanadium and chromium leaching ratios were always opposite because of the competitive reactions of oxidation and calcification between vanadium and chromium with CaO. Moreover, CaO was more likely to combine with vanadium, as further confirmed by thermodynamic analysis. When the HCVS with CaO added in an n(CaO)/ n(V2O5) ratio of 0.5 was roasted in an air atmosphere at a heating rate of 10°C/min from room temperature to 950°C and maintained at this temperature for 60 min, the leaching ratios of vanadium and chromium reached 91.14% and 0.49%, respectively; thus, efficient extraction of vanadium from HCVS was achieved and the leaching residue could be used as a new raw material for the extraction of chromium. Furthermore, the oxidation and calcification reactions of the spinel phases occurred at 592 and 630°C for n(CaO)/ n(V2O5) ratios of 0.5 and 5, respectively.

Problems in the determination of chromium in biological materials

International Nuclear Information System (INIS)

Behne, D.; Braetter, P.; Gessner, H.; Hube, G.; Mertz, W.; Roesick, U.

1976-01-01

The effects of sample preparation on the analysis of chromium in biological matter have been investigated using brewer's yeast as a test material. The apparent chromium content of the yeast as determined by flameless atomic absorption spectrometry was significantly higher after destruction of the organic matter with HNO 3 in a closed pressure vessel than after wet-ashing in open vessels and after direct introduction of the sample into the graphite furnace. The results obtained by neutron activation analysis without any sample preparation, which corresponded to the atomic absorption values after digestion in the pressure vessel, showed that considerable errors arise in the other methods of sample treatment. Chromium analysis of dried and ashed yeast suggest that losses of volatile chromium compounds may occur during heating. (orig.) [de

Performance analysis on natural energy autonomous house (HARBEMAN house); Shizen energy jiritsu house (HARBEMAN house) ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujino, T; Saito, T [Tohoku University, Sendai (Japan)

1996-10-27

To reduce fossil fuel consumption and CO2 emission, this article introduces an actually constructed natural energy autonomous house. It has a solar collector on the south roof for hot water supply and a sky radiator on the north roof for cooling water supply. The sky radiator uses radiation cooling phenomena into the space by electromagnetic wave through the window of atmosphere. This house also has an insulated tank with a capacity of 31 m{sup 3} in its underground. In the long-term heat storage mode, the heat is collected through the solar radiation during the period from summer to spring and is stored in the underground water tank, to use it for heating and hot water supply in winter. The heat can be recovered from the garbage waste incinerator. A gas fired auxiliary boiler is used for the shortage. In the long-term heat regeneration mode, the heat is regenerated through the sky radiator during the period from spring to summer and is stored in the underground water tank, to use it for cooling in summer. For the shortage, the water is cooled using a heat pump operated by the midnight power. The insulating performance is improved by using the pair glass in windows and the glass wool in the walls. Rain water is collected in a tank with a capacity of 2 m{sup 3}, to use it for toilet water. Annual energy and water saving is equivalent to 600,000 yen. 10 refs., 10 figs., 2 tabs.

Magnesium analysis. Spectrophotometric determination of chromium

International Nuclear Information System (INIS)

Anon.

Chromium determination in magnesium used in uranium fabrication by magnesiothermics, applicable for chromium content between 2 to 10 ppm. Magnesium is dissolved in sulfuric acid, oxidized by potassium permanganate, the excess of permanganate is eliminated by sodium nitride. Spectrophotometry at 540 nm of the chromium (VI)-diphenylcarbazide complex [fr

Crystallite size effect on the monoclinic deformation of the bcc crystal structure of chromium

Science.gov (United States)

Przeniosło, R.; Fabrykiewicz, P.; Sosnowska, I.; Wardecki, D.; Sławiński, W. A.; Playford, H. Y.; Hempelmann, R.; Bukowski, M.

2018-02-01

The modulated spin density wave magnetic orderings observed in chromium suggests that the crystal structure of chromium cannot be described by the cubic space group Im 3 bar m. Our experimental studies of polycrystalline and nanocrystalline chromium by synchrotron radiation (SR) and neutron powder diffraction show a hkl-dependent Bragg peak broadening which can be interpreted by the low-symmetry monoclinic space group P21 / n instead of the high symmetry cubic space group Im 3 bar m. The monoclinic angle is βm = 90.05(1)° and 90.29(1)° for polycrystalline Cr and nanocrystalline Cr, respectively. The relative monoclinic distortion observed in chromium is 5 times larger than those reported for several oxides: BiFeO3, α-Fe2O3, Cr2O3 and calcite. The symmetry of the magnetic transverse spin density wave (TSDW) and the longitudinal spin density wave (LSDW) observed in Cr are described by using the superspace groups P21 / n(0 β 0) 00 and P 21‧ /n‧(0 β 0) 00, respectively. These superspace groups describe both the magnetic modulations and the atomic position modulations reported in the literature. The monoclinic symmetry of chromium is a robust effect which is observed in the paramagnetic as well as in the TSDW and LSDW phases.

40 CFR Appendix Xii to Part 266 - Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery Furnaces XII Appendix XII to Part 266... FACILITIES Pt. 266, App. XII Appendix XII to Part 266—Nickel or Chromium-Bearing Materials that may be...

Effect of the gamma radiation in hydrotalcite with chromates

International Nuclear Information System (INIS)

Martinez G, S.; Bulbulian, S.

2004-01-01

At the moment the generation of radioactive wastes is topic of numerous studies. In this work was retained anionic material, chromates, in hydrotalcite that are anionic exchangers. It was proposed to warm the HT at different temperatures of 600 C up to 1200 C with the purpose of immobilizing the chromium inside the hydrotalcite. To high temperatures (1000 and 1200 C) it was formed one spinel (MgCr 2 O 4 ) that is a very stable compound. It was found that when increasing the heating temperature, the anions are retained strongly. The immobilization of the Cr was determined through the chromium lixiviation with solutions 1N and 5N of NaCl. Also it was studied the effect of the radiation on the heated materials. The radiation dose used for it was of 1000 and 6000 kGy. The results show that for the calcined samples at 1000 and 1200 C irradiated or no irradiated, the chromium is strongly retained in form of spinels that is the structure formed after the calcination of the material. (Author)

Chromium: a review of environmental and occupational toxicology.

Science.gov (United States)

Bencko, V

1985-01-01

The following topics are covered in this brief review on the environmental and occupational toxicology of chromium: occurrence, production and uses of chromium and chromium compounds; experimental toxicology; chromium toxicity for man; hygienic and ecologic aspects of chromium contamination of the environment. The review provides a conclusive evidence which suggests that chromium, especially its hexavalent form, is both toxic and carcinogenic, but its trivalent form is physiologically essential in the metabolism of insulin. It is also emphasized that among the major sources of environmental chromium today are the cement industry and the increasingly widespread use of chromium compounds added as an anticorrosion admixture to a variety of cooling systems, e.g. in large power plants, which may greatly contribute to the overall pollution of outdoor air at the sites.

Chromium: a review of environmental and occupational toxicology

Energy Technology Data Exchange (ETDEWEB)

Bencko, V

1985-01-01

The following topics are covered in this brief review on the environmental and occupational toxicology of chromium: occurrence, production and uses of chromium and chromium compounds; experimental toxicology; chromium toxicity for man; hygienic and ecologic aspects of chromium contamination of the environment. The review provides a conclusive evidence which suggests that chromium, especially its hexavalent form, is both toxic and carcinogenic, but its trivalent form is physiologically essential in the metabolism of insulin. It is also emphasized that among the major sources of environmental chromium today are the cement industry and the increasingly widespread use of chromium compounds added as an anticorrosion admixture to a variety of cooling systems, e.g. in large power plants, which may greatly contribute to the overall pollution of outdoor air at the sites. 108 references.

Chromium in Drinking Water: Association with Biomarkers of Exposure and Effect

Science.gov (United States)

Sazakli, Eleni; Villanueva, Cristina M.; Kogevinas, Manolis; Maltezis, Kyriakos; Mouzaki, Athanasia; Leotsinidis, Michalis

2014-01-01

An epidemiological cross-sectional study was conducted in Greece to investigate health outcomes associated with long-term exposure to chromium via drinking water. The study population consisted of 304 participants. Socio-demographics, lifestyle, drinking water intake, dietary habits, occupational and medical history data were recorded through a personal interview. Physical examination and a motor test were carried out on the individuals. Total chromium concentrations were measured in blood and hair of the study subjects. Hematological, biochemical and inflammatory parameters were determined in blood. Chromium in drinking water ranged from Chromium levels in blood (median 0.32 μg·L−1, range chromium exposure dose via drinking water, calculated from the results of the water analyses and the questionnaire data, showed associations with blood and hair chromium levels and certain hematological and biochemical parameters. Groups of subjects whose hematological or biochemical parameters were outside the normal range were not correlated with chromium exposure dose, except for groups of subjects with high triglycerides or low sodium. Motor impairment score was not associated with exposure to chromium. PMID:25268509

Recent advances in role of chromium and its antioxidant combinations in poultry nutrition: A review

Directory of Open Access Journals (Sweden)

Z. Haq

2016-12-01

Full Text Available Poultry is reared in open side houses in most of the tropical countries, which results in huge temperature variation in shed causing stress resulting in increased demand of antioxidant supplementation. Since cooling of poultry houses or environment control is very expensive, thus methods focused on nutritional modifications appears to be the much logical approach. Stress increases mineral and vitamin mobilization from tissues and their excretion. Effect of some minerals and vitamin supplements such as chromium (Cr and ascorbic acid to elevate the negative effects of environmental stress is well documented. Cr functions as an antioxidant and its deficiency are said to disrupt carbohydrate and protein metabolism. Cr has been utilized for weight gain, to improve feed conversion ratio, increase relative organ weight, muscle development, decrease cholesterol, increase high-density lipoprotein cholesterol, and improve nutrient digestion. Therefore, the present review discusses the beneficial aspects of Cr with its effect in different doses and antioxidant combinations to explore and promote its optimum utilization in poultry nutrition and production.

Spectrophotometric determination of chromium in geological samples

International Nuclear Information System (INIS)

Rathore, D.P.S.; Tarafder, P.K.

1992-01-01

A method for the determination of chromium is presented, based on the oxidation of hydroxylamine hydrochloride to nitrous acid by chromium(VI) in acetic acid medium followed by diazotization of the nitrite produced with p-aminophenylmercaptoacetic acid and subsequent coupling of the diazonium salt with N-(1-naphthyl)ethylenediamine di-hydrochloride in acidic medium to form a stable blueish azo dye. The method is suitable for the determination of chromium(VI) from 0.04 to 1.2 mg l -1 in a 1.0-cm cuvette. The molar absorptivity and Sandell's sensitivity are 3.65x10 4 l mol -1 cm -1 and 0.0014μg cm -2 , respectively. (author). 17 refs.; 3 figs

Synthesis of chromium containing pigments from chromium galvanic sludges

International Nuclear Information System (INIS)

Andreola, F.; Barbieri, L.; Bondioli, F.; Cannio, M.; Ferrari, A.M.; Lancellotti, I.

2008-01-01

In this work the screening results of the scientific activity conducted on laboratory scale to valorise chromium(III) contained in the galvanic sludge as chromium precursor for ceramic pigments are reported. The valorisation of this waste as a secondary raw material (SRM) is obtained by achievement of thermal and chemical stable crystal structures able to color ceramic material. Two different pigments pink CaCr 0.04 Sn 0.97 SiO 5 and green Ca 3 Cr 2 (SiO 4 ) 3 were synthesized by solid-state reactions using dried Cr sludge as chromium oxide precursor. The obtained pigments were characterized by X-ray diffraction and SEM analysis. Furthermore the color developed in a suitable ceramic glaze was investigated in comparison with the color developed by the pigments prepared from pure Cr 2 O 3 . The characterization carried out corroborates the thermal and chemical stability of the synthesized pigments and, especially for the Cr-Sn pink pigment, the powders develop an intense color that is very similar to the color developed by the pigments obtained starting from pure Cr 2 O 3

Chromium depletion from stainless steels during vacuum annealing

International Nuclear Information System (INIS)

Smith, A.F.; Hales, R.

1977-01-01

During selective chromium oxidation of stainless steels the changes in chromium concentration at the metal surface and in the metal have an important bearing on the overall oxidation performance. It has been proposed that an analogue of chromium behaviour during selective oxidation is obtained from volatilisation of chromium during high temperature vacuum annealing. In the present report the evaporation of chromium from 316 type of steel, vacuum annealed at 1,000 0 C, has been investigated by means of energy dispersive X-ray analysis and by neutron activation analysis. It was established that chromium loss from austenitic stainless steels is rate controlled by interdiffusion in the alloy. As predicted the chromium concentration at the metal surface decreased with increasing vacuum annealing time. The chromium depletion profile in the metal was in good agreement with the previously derived model apart from an anomalous region near the surface. Here the higher resolution of the neutron activation technique indicated a zone within approximately 2μm of the surface where the chromium concentration decreased more steeply than expected. (orig.) [de

Study on Public Exposure and External Radiation Level at Gamma Green House and around MINT Dengkil Complex Boarder

International Nuclear Information System (INIS)

Faizal Azrin Abdul Razalim; Ismail Sulaiman; Khairuddin Mohamad Kontol; Ahmad Bazlie Abdul Kadir; Noor Fadilla Ismail; Hassan Sham; Ahmad Zainuri Mohd Dzomir

2014-01-01

This paper will discussing on the measurement of external radiation and the dose level which is acceptable to the public around the Gamma Green House and the border between Malaysian Nuclear Agency and housing project developed by Mah Sing Group. This research is made to verify the level of safety, especially for civilians residing in this area and to ensure compliance with the limit that has been set by the authorities, AELB (BSS/2010). Measurement method used in this research by using survey meter, TLD and OSL. (author)

Corrosion behaviour of porous chromium carbide/oxide based ceramics in supercritical water

International Nuclear Information System (INIS)

Dong, Z.; Xin, T.; Chen, W.; Zheng, W.; Guzonas, D.

2011-01-01

Porous chromium carbide with a high density of open pores was fabricated by a reactive sintering method. Chromium oxide ceramics were obtained by re-oxidizing the porous chromium carbides formed. Some samples were added with yttria at 5 wt. %, prior to reactive sintering to form porous structures. Corrosion tests in SCW were performed at temperatures ranging from 375 o C to 625 o C with a fixed pressure at around 25∼30 MPa. The results show that chromium carbide is stable in SCW environments at temperatures up to 425 o C, above which disintegration of carbides through oxidation occurs. Porous chromium oxide samples show better corrosion resistance than porous chromium carbide, but disintegrate in SCW at around 625 o C. Among all the samples tested, chromium oxide ceramics with added yttria exhibited much better corrosion resistance compared with the pure chromium carbide/oxides. No evidence of weight change or disintegration of porous chromium oxides with 5 wt % added yttria was observed after exposure at 625 o C in SCW for 600 hours. (author)

Assessment of the level of chromium species in the discharged ...

African Journals Online (AJOL)

The purpose of this study was to assess the level of chromium species in the discharged effluents of selected tanneries in the Amhara Region; Haik and Debre Berhan tanneries. The level of total chromium, and hexavalent chromium in the discharged effluent of the studied tanneries were determined using the ICP-OES, and ...

An experimental study of the shielding characteristics of the dwelling house building materials against gamma radiations in the Central Region of Syria

International Nuclear Information System (INIS)

Albarhoum, M.; Soufan, A.H.; Mustafa, H.

2011-01-01

Highlights: → We measure shielding properties of dwelling houses in the central region of Syria. → The concrete used for ceiling construction is good for shielding from gamma radiations. → Fairly high linear attenuation coefficients are obtained (from 0.173 to 0.198 cm -1 ). → Blocks used for house walls are not effective against gamma radiations. → Blocks efficiency can be improved by filling their holes with a cement paste. - Abstract: The shielding properties of the concrete and blocks used for the construction of dwelling houses in the Central Region of Syria (CRS) were measured and studied. The concrete used for the ceiling construction was found to have optimum shielding properties with 0.182 cm -1 (or equivalently 0.0859 cm 2 g -1 ) for the linear (mass) attenuation coefficient [L(M)AC]. In addition gamma radiation is attenuated by 73.221% on average, while the blocks used for the walls have smaller LACs (0.082 cm -1 for the bare blocks, and 0.118 cm -1 for the coated ones). Although the LACs for the blocks are smaller than those for the concrete their shielding properties are good to protect from the gamma radiations coming from radioactive or nuclear accidents (78.630% attenuation), even Chernobyl - like disasters, because of their big width (10-12 cm). The LACs were measured by an ionization chamber and simple theoretical calculations have been made to predict the concrete LACs. The calculations showed an average LAC for the six samples equal to 0.1664 cm -1 with 8.47% error with respect to the experimental values. The average LAC for the concrete used for ceiling construction in the CRS was found to be comparable or even better than the average of some international values for the reactor shielding concretes, which are about 0.163 cm -1 .

Use of thermogravimetry and thermodynamic calculations for specifying chromium diffusion occurring in alloys containing chromium carbides during high temperature oxidation

International Nuclear Information System (INIS)

Berthod, Patrice; Conrath, Elodie

2015-01-01

The chromium diffusion is of great importance for the high temperature oxidation behaviour of the chromium-rich carbides-strengthened superalloys. These ones contain high chromium quantities for allowing them well resisting hot corrosion by constituting and maintaining a continuous external scale of chromia. Knowing how chromium can diffuse in such alloys is thus very useful for predicting the sustainability of their chromia-forming behaviour. Since Cr diffusion occurs through the external part of the alloy already affected by the previous steps of oxidation (decarburized subsurface) it is more judicious to specify this diffusion during the oxidation process itself. This was successfully carried out in this work in the case of a model chromia-forming nickel-based alloy containing chromium carbides, Ni(bal.)–25Cr–0.5C (in wt.%). This was done by specifying, using real-time thermogravimetry, the mass gain kinetic due to oxidation, and by combining it with the post-mortem determination of the Cr concentration profiles in subsurface. The values of D Cr thus obtained for 1000, 1050 and 1100 °C in the alloy subsurface are consistent with the values obtained in earlier works for similar alloy's chemical compositions. - Highlights: • A Ni25Cr0.50C alloy was oxidized at high temperature in a thermo-balance. • The mass gain files were analysed to specify the Cr 2 O 3 volatilization constant K v . • Concentration profiles were acquired to specify the chromium gradient. • The diffusion coefficient of chromium through the subsurface was deduced. • The obtained diffusion coefficient is consistent with values previously obtained.

Molecular Mechanisms of Chromium in Alleviating Insulin Resistance

Science.gov (United States)

Hua, Yinan; Clark, Suzanne; Ren, Jun; Sreejayan, Nair

2011-01-01

Type 2 diabetes is often associated with obesity, dyslipidemia, and cardiovascular anomalies and is a major health problem approaching global epidemic proportions. Insulin resistance, a prediabetic condition, precedes the onset of frank type 2 diabetes and offers potential avenues for early intervention to treat the disease. Although lifestyle modifications and exercise can reduce the incidence of diabetes, compliance has proved to be difficult, warranting pharmacological interventions. However, most of the currently available drugs that improve insulin sensitivity have adverse effects. Therefore, attractive strategies to alleviate insulin resistance include dietary supplements. One such supplement is chromium, which has been shown reduce insulin resistance in some, but not all, studies. Furthermore, the molecular mechanisms of chromium in alleviating insulin resistance remain elusive. This review examines emerging reports on the effect of chromium, as well as molecular and cellular mechanisms by which chromium may provide beneficial effects in alleviating insulin resistance. PMID:22423897

On texture formation of chromium electrodeposits

DEFF Research Database (Denmark)

Nielsen, Christian Bergenstof; Leisner, Peter; Horsewell, Andy

1998-01-01

The microstructure, texture and hardness of electrodeposited hard, direct current (DC) chromium and pulsed reversed chromium has been investigated. These investigations suggest that the growth and texture of hard chromium is controlled by inhibition processes and reactions. Further, it has been...

Stabilization of chromium: an alternative to make safe leathers.

Science.gov (United States)

Gong, Ying; Liu, Xiaoling; Huang, Li; Chen, Wuyong

2010-07-15

In this study, the original causes for hexavalent chromium presence in the leather were first evaluated by ageing of chromium(III) solutions and chrome tanned hide powder (50 degrees C, UV lightening at 340 nm, 0-36 h). The results showed that the trivalent chromium at instable coordination state was easy to convert into hexavalent chromium in high pH environment, and the probability of the oxidation increased in this order: multi-coordinate chromium, mono-coordinate chromium, and free chromium. For this reason, the process for stabilizing chromium in the leather was designed with the specific material, which was mostly consisted of the reducers and the chelating agents. After treated with the developed process, these leathers were aged (50 degrees C, UV irradiance as 0.68 W/m(2) at 340 nm, 0-72 h) to estimate chromium(VI) presence. Hexavalent chromium was not found in these treated leathers even if the leathers were aged for 72 h. Moreover, the physical and mechanical properties for the leathers varied little after treating. In a word, an inherent safe and effective process was proved to avoid the formation of hexavalent chromium in the leather. 2010 Elsevier B.V. All rights reserved.

Recovery of Proteins and Chromium Complexes from Chromium – Containing Leather Waste (CCLW

Directory of Open Access Journals (Sweden)

B. Gutti

2010-08-01

Full Text Available Chromium – Containing Leather Waste (CCLW constitutes an environmental pollution problem to leather industries disposing the waste by landfill. The waste mainly consists of collagen and chromium III complexes. This work is a design of reactors to recover gelatin, polypeptides and chromium from CCLW. The results of the experiment shows that 68% of protein, based on dry weight of leather scraps, could be recovered. Three reactors with a total volume of 18 m3 was designed to handle 10,431 kg of waste generated from the tanning industries.

Determination of total chromium in tanned leather samples used in car industry.

Science.gov (United States)

Zeiner, Michaela; Rezić, Iva; Ujević, Darko; Steffan, Ilse

2011-03-01

Despite the high competition of synthetic fibers leather is nowadays still widely used for many applications. In order to ensure a sufficient stability of the skin matrix against many factors, such as microbial degradation, heat and sweat, a tanning process is indispensable. Using chromium (III) for this purpose offers a multitude of advantages, thus this way of tanning is widely applied. During the use of chromium tanned leather as clothing material as well as for decoration/covering purposes, chromium is extracted from the leather and may then cause nocuous effects to human skin, e.g. allergic reactions. Thus the knowledge of the total chromium content of leather samples expected to come into prolonged touch with human skin is very important. In car industry leather is used as cover for seats, steering wheel and gearshift lever The chromium contents often chromium tanned leather samples used in car industry were determined. First all samples were dried at 65 degrees C overnight and then cut in small pieces using a ceramic knife, weighed and analyzed by inductively coupled plasma--optical emission spectrometry (ICP-OES) after acidic microwave assisted digestion. The total chromium amounts found were in the range from 19 mg/g up to 32 mg/g. The extraction yield of chromium from leather samples in sweat is approximately 2-7%. Thus especially during long journeys in summer chromium can be extracted in amounts which may cause nocuous effects for example on the palm of the hands or on the back.

Characteristics of oxidation of low-alloyed chromium in nitrogen tetroxide

International Nuclear Information System (INIS)

Kamenev, A.Ya.; Goncharova, N.V.; Kopets, Z.V.; Tedushin, E.E.

1985-01-01

The effect of N 2 O 4 on corrosion properties of chromium-based alloys is studied. The method of structural materials analysis is described using as an example chromium-based alloys in the flow of chemically active N 2 O 4 at high temperatures. The method has been used to study corrosive behaviour of chromium at temperatures 923, 1073 and 1273 K. The time of exposure amounts up to 140 hours. The wave-like time dependence of mass velocity variation has been observed for all chromium samples under test. The time of the alloy exposure to N 2 O 4 medium and the nature of the alloying affect this dependence. The given metallograhic studies of chromium alloys show complex structure of the surface layer

Surface Chemistry and Spectroscopy of Chromium in Inorganic Oxides

NARCIS (Netherlands)

Weckhuysen, B.M.; Wachs, I.E.; Schoonheydt, R.A.

1996-01-01

Focuses on the surface chemistry and spectroscopy of chromium in inorganic oxides. Characterization of the molecular structures of chromium; Mechanics of hydrogenation-dehydrogenation reactions; Mobility and reactivity on oxidic surfaces.

Annual experimental results on heat and cool storage modes for natural energy autonomous house, HARBEMAN house; Shizen energy jiritsu house (HARBEMAN house) no chikunetsu chikurei mode no jissoku kekka

Energy Technology Data Exchange (ETDEWEB)

Saito, T; Fujino, T; Suzuki, M [Tohoku University, Sendai (Japan)

1997-11-25

Outlined herein is performance of the solar system, followed for a year, installed in a solar house (HARBEMAN HOUSE) built in 1996 in City of Sendai. The house is equipped, on the roof, with a 30.42m{sup 2} wide solar collector on the south and sky radiator on the north. They are connected to a heat-insulated tank (31m{sup 3}) installed underground, storing hot or cool water which carries energy for heating/air-conditioning and hot water. The solar system operates in a long-term hot or cool water storage mode. In the hot water storage mode, the solar collector is connected to the underground main tank, where pumped-up water heated by solar heat is stored to be supplied as hot water. Heat collected is low during the December-February period, and recovered in March. In the cool water storage mode, the radiator is connected to the underground main tank, where pumped-up water is cooled by radiation and stored to be supplied to a fan coil unit in each room for air-conditioning. The recorded lowest temperature of water in the tank is 5.1degC. No air-conditioning load is observed, on account of the unseasonal weather. 3 refs., 10 figs., 2 tabs.

Biosorption of hexavalent chromium in a tannery industry wastewater using fungi species

International Nuclear Information System (INIS)

Sivakumar, D.

2016-01-01

The isolated fungi species of different kinds from chromium contaminated soil sites located in Nagalkeni, Chennai were used for reducing chromium(VI) in a tannery industry wastewater of Nagalkeni, Chennai. The experiments were conducted to know biosorption potential of isolated fungi species for removing chromium(VI) in a tannery industry wastewater against the different p H, fungi biomass and chromium(VI) concentration (dilution ratio). The results of this study indicated that the order of maximum removal of chromium(VI) by an isolated fungi species at an optimum pH of 3, fungi biomass of 4g and an initial chromium(VI) concentration of 18.125 mg/L (dilution ratio 4) is A. niger > A. flavus > A. fumigatus > A. nidulans > A. heteromorphus > A. foetidus > A. viridinutans. This study found that the maximum removal of chromium(VI) was achieved by Aspergillus niger (96.3 %) than other fungi species at chromium(VI) concentration of 18.125 mg/L in a tannery industry wastewater. The chromium removal from tannery industry wastewater was validated by checking chromium removal in an aqueous solution and by checking the removal efficiency of other parameters in a tannery industry wastewater using same isolated A. niger. Biosorption model was proposed to simulate the experimental condition for removing chromium(VI) in a tannery industry wastewater by all isolated fungi species. The R2 and x2 values of the proposed model predicted that the proposed biosorption model is very much useful for predicting the trend of reduction potential of chromium(VI) in a tannery industry wastewater by all isolated fungi species. This study suggested that one could select the type of fungi species, ion concentration level, selection of treatment period, quantity of biomass to be used, and p H level of the medium, to achieve the highest reduction of any toxic metals from any contaminated water, wastewater and soil environment.

Specification for corrosion-resisting chromium and chromium-nickel steel bare and composite metal cored and stranded arc welding electrodes and welding rods

International Nuclear Information System (INIS)

Anon.

1983-01-01

This specification prescribes requirements for corrosion or heat resisting chromium and chromium-nickel steel electrodes and welding rods. These electrodes and welding rods are normally used for arc welding and include those alloy steels designated as corrosion or heat-resisting chromium and chromium-nickel steels, in which chromium exceeds 4.0 percent and nickel does not exceed 50.0 percent

Production of basic chromium sulfate by using recovered chromium from ashes of thermally treated leather.

Science.gov (United States)

Dettmer, Aline; Nunes, Keila Guerra Pacheco; Gutterres, Mariliz; Marcílio, Nilson Romeu

2010-04-15

Leather wastes tanned with chromium are generated during the production process of leather, hence the wastes from hand crafted goods and footwear industries are a serious environmental problem. The thermal treatment of leather wastes can be one of the treatment options because the wastes are rich in chromium and can be used as a raw material for sodium chromate production and further to obtain several chromium compounds. The objective of this study was to utilize the chromium from leather wastes via basic chromium sulfate production to be subsequently applied in a hide tanning. The obtained results have shown that this is the first successful attempt to achieve desired base properties of the product. The result was achieved when the following conditions were applied: a molar ratio between sodium sulfite and sodium dichromate equal to 6; reaction time equal to 5 min before addition of sulfuric acid; pH of sodium dichromate solution equal to 2. Summarizing, there is an opportunity to utilize the dangerous wastes and reused them in the production scheme by minimizing or annulling the environmental impact and to attend a sustainable process development concept. 2009 Elsevier B.V. All rights reserved.

Auxiliary Electrodes for Chromium Vapor Sensors

Energy Technology Data Exchange (ETDEWEB)

Fergus, Jeffrey; Shahzad, Moaiz; Britt, Tommy

2018-05-15

Measurement of chromia-containing vapors in solid oxide fuel cell systems is useful for monitoring and addressing cell degradation caused by oxidation of the chomia scale formed on alloys for interconnects and balance-of-plant components. One approach to measuring chromium is to use a solid electrolyte with an auxiliary electrode that relates the partial pressure of the chromium containing species to the mobile species in the electrolyte. One example is YCrO3 which can equilibrate with the chromium containing vapor and yttrium in yttria stabilized zirconia to establish an oxygen activity. Another is Na2CrO4 which can equilibrate with the chromium-containing vapor to establish a sodium activity.

Kinetics of chromium (VI) reduction by ferrous iron

International Nuclear Information System (INIS)

Batchelor, B.; Schlautman, M.; Hwang, I.; Wang, R.

1998-09-01

Chromium is a primary inorganic contaminant of concern at the Pantex Plant. Chromium concentrations have been found to be two orders of magnitude higher than the drinking water standards, particularly in certain wells in the perched aquifer below Zone 12. In situ reduction of a mobile form of chromium, Cr(VI) to an immobile form, Cr(III), was examined as a viable option to active soil restoration. Successfully immobilizing chromium in the vadose zone as Cr(III) will reduce the amount of chromium that reaches the groundwater table. The results from the solution experiments indicated that chromium was rapidly and stoichiometrically reduced by Fe(II) in solution. Also, the slurry experiments showed that the aquifer solids removed Fe(II) from solution, but a portion of the iron removed remained available for reaction with Cr(VI), but at a slower rate. A model to predict different amounts of iron pseudo-components was developed, which allowed prediction of iron amounts required to reduce chromium under in situ conditions

Chronic occupational exposure to hexavalent chromium causes DNA damage in electroplating workers

Directory of Open Access Journals (Sweden)

Ren Xiao-Bin

2011-04-01

Full Text Available Abstract Background Occupational exposure to chromium compounds may result in adverse health effects. This study aims to investigate whether low-level hexavalent chromium (Cr(VI exposure can cause DNA damage in electroplating workers. Methods 157 electroplating workers and 93 control subjects with no history of occupational exposure to chromium were recruited in Hangzhou, China. Chromium levels in erythrocytes were determined by graphite furnace atomic absorption spectrophotometer. DNA damage in peripheral lymphocytes was evaluated with the alkaline comet assay by three parameters: Olive tail moment, tail length and percent of DNA in the comet tail (tail DNA%. Urinary 8-OHdG levels were measured by ELISA. Results Chromium concentration in erythrocytes was about two times higher in electroplating workers (median: 4.41 μg/L than that in control subjects (1.54 μg/L, P P P P Conclusion The findings in this study indicated that there was detectable chromium exposure in electroplating workers. Low-level occupational chromium exposure induced DNA damage.

Stabilization of chromium salt in ordinary portland cement

Indian Academy of Sciences (India)

Ordinary Portland cement (OPC) samples containing the chromium salt have been investigated using differential microcalorimetry, conductometry and Fourier transform infrared spectroscopic analysis. The effect of chromium on OPC hydration was evaluated by continuous observing of early hydration.

Sources of radioactive contamination inside houses

International Nuclear Information System (INIS)

Sajet, A.S.

2010-01-01

People may be exposed at home to multiple sources of nuclear radiation such as gamma, beta and alpha rays emitters. House atmosphere is polluted with nuclear radiation from water pollutants and rocks used in the construction. Radon is the only radioactive non-metallic element. Environmental organizations estimated that all houses contain varying concentrations of radon gas, and the residents are exposed to levels of radon over the years. The source of radon in houses is uranium, which may be found in rocks of the house, soil of the garden, water of the deep artesian wells and building materials, especially granite rocks. Breathing air that contains high levels of radon causes lung cancer. Radon is the second cause of lung disease after smoking. There are many means to reduce house pollution including: utilisation of air filters to remove contaminated dust particles, keep residential areas away from the establishments that use nuclear technology or embedded by nuclear waste, avoid using materials made from asbestos in construction works and proper use and disposal of chemicals and medicines containing radioactive isotopes. (author)

Fractionation of chromium(III) compounds in biological matrices

Energy Technology Data Exchange (ETDEWEB)

Knoechel, A.; Weseloh, G. [Institute of Inorganic and Applied Chemistry, University of Hamburg (Germany)

1999-03-01

Many details of the metabolism and biological significance of trivalent inorganic cations have remained obscure up to now, not least because of the lack of appropriate tools for species analysis of these cations in biological matrices. In order to demonstrate the capabilities of reversed-phase ion-pair chromatography, the distribution of chromium species in brewer`s yeast, previously incubated with radiolabelled {sup 51}Cr chloride was investigated. Contradictory to the findings of most other researchers in this area, two low-molecular weight, anionic chromium species were detected in cytosolic yeast extracts. In conclusion, reversed-phase ion-pair chromatography may reveal new details of intracellular metabolism of chromium(III) and, possibly, other trivalent cations. (orig.) With 1 fig., 16 refs.

Chromium allergy and dermatitis: prevalence and main findings

DEFF Research Database (Denmark)

Bregnbak, David; Johansen, Jeanne D.; Jellesen, Morten Stendahl

2015-01-01

The history of chromium as an allergen goes back more than a century, and includesan interventional success with national legislation that led to significant changes inthe epidemiology of chromium allergy in construction workers. The 2015 EU Leather Regulation once again put a focus on chromium...... allergy, emphasizing that the investigation of chromium allergy is still far from complete. Our review article on chromium focuses on the allergen’s chemical properties, its potential exposure sources, and the allergen’s interaction with the skin, and also provides an overview of the regulations...

21 CFR 73.2327 - Chromium oxide greens.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium oxide greens. 73.2327 Section 73.2327... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2327 Chromium oxide greens. (a) Identity and specifications. The color additive chromium oxide greens shall conform in identify and specifications to the...

21 CFR 73.2326 - Chromium hydroxide green.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium hydroxide green. 73.2326 Section 73.2326... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2326 Chromium hydroxide green. (a) Identity and specifications.The color additive chromium hydroxide green shall conform in identity and specifications to the...

Measurements of indoor and outdoor natural radiation exposure rates in model houses

International Nuclear Information System (INIS)

Matsuda, Hideharu; Fukaya, Mitsuharu; Minato, Susumu

1990-01-01

Natural gamma-ray and cosmic-ray exposure rates were measured indoors and outdoors for 94 model houses of four housing centers in Nagoya to obtain basic data for estimation of the population dose. Influence of the structure of houses on indoor exposure rates and relationship between indoor and outdoor natural gamma-ray exposure rates were studied. Exposure rates were measured with a 1.5'' φ x 4'' NaI (Tl) scintillation counter and a 6''φ spherical plastic scintillation counter. The mean indoor natural gamma-ray exposure rate in ferro-concrete buildings was about 40% higher than that in fireproof wooden houses, about 60% higher than that in light-weight steel-framed buildings, in fireproof wooden houses, it was also about 10% higher than in light-weight steel-framed building. The ratio of indoor to outdoor natural gamma-ray exposure rate was found to be about 0.95±0.15, 0.77±0.10, and 0.72±0.13 for ferro-concrete buildings, fireproof wooden houses and light-weight steel-framed buildings, respectively. The mean indoor cosmic-ray exposure rate in ferro-concrete buildings was 2.8 μR/h, about 18% lower than the outdoors. The indoor cosmic-ray exposure rate in fireproof wooden houses and light-weight steel-framed buildings were 3.2 μR/h, about 6% lower than the outdoors. (author)

Segregation and precipitation in iron-chromium alloys during thermal ageing and irradiation

International Nuclear Information System (INIS)

Senninger, O.

2013-01-01

Iron-Chromium alloys have a peculiar thermodynamic and diffusion behavior which is due to their magnetic properties. The alloy decomposition under thermal ageing has been studied in this thesis. An atomistic kinetic model has been performed in this aim in which we have modeled in details the chemical species thermodynamic and diffusion properties. In particular, the evolution of elements diffusion properties which the ferro-paramagnetic transition has been introduced in the model. Simulated decompositions have been compared with experiments for a large range of concentrations and temperatures. A good agreement between simulations and experiments was observed and these comparisons have highlighted the ferro to paramagnetic transition key role in the concentrated alloys kinetic decomposition. This study has also evidenced that the elements diffusion at phases interfaces is responsible for the alloy decomposition kinetic in long lasting.We have also started a study of the alloy radiation induced segregation. For that purpose, atomistic kinetic model has been performed modeling defects migration through a perfect planar sink. It have been shown, I agreement with former studies, that chromium tends to segregate in the vicinity of sinks at low temperatures and deplete at high temperature. (author) [fr

Chromium Uptake Efficiency of Spinacea olaracea from ...

African Journals Online (AJOL)

The aim of the study was to evaluate the uptake of chromium by Spinacea olaracea and its accumulation in roots and shoots of plants grown in pots at various concentrations of chromium (30, 60, 90,120,150 mg/l). The results revealed that the levels of chromium accumulation in roots and shoots were higher at minimum ...

Bioremediation of chromium in tannery effluent by microbial consortia

African Journals Online (AJOL)

USER

2010-05-24

May 24, 2010 ... Chromium is the most toxic and common among the heavy metal pollutants of industrial effluents .... Chromium (Cleseari and Green, 1995) included the oxidation of .... like uranium in its cells might also match with its tendency.

Chromium in Postmortem Material.

Science.gov (United States)

Dudek-Adamska, Danuta; Lech, Teresa; Konopka, Tomasz; Kościelniak, Paweł

2018-04-17

Recently, considerable attention has been paid to the negative effects caused by the presence and constant increase in concentration of heavy metals in the environment, as well as to the determination of their content in human biological samples. In this paper, the concentration of chromium in samples of blood and internal organs collected at autopsy from 21 female and 39 male non-occupationally exposed subjects is presented. Elemental analysis was carried out by an electrothermal atomic absorption spectrometer after microwave-assisted acid digestion. Reference ranges of chromium in the blood, brain, stomach, liver, kidneys, lungs, and heart (wet weight) in the population of Southern Poland were found to be 0.11-16.4 ng/mL, 4.7-136 ng/g, 6.1-76.4 ng/g, 11-506 ng/g, 2.9-298 ng/g, 13-798 ng/g, and 3.6-320 ng/g, respectively.

Acute and chronic systemic chromium toxicity.

Science.gov (United States)

Gad, S C

1989-10-01

Although chromium and compounds containing it have been recognized as having potential severe adverse effects on health for more than 160 years, understanding of the systemic toxicology and true hazard of these compounds is still not complete. A review of the current state of knowledge is attempted in this paper, with appropriate attention given to the complications of multiple valence states and solubility. Selected chromium compounds, particularly hexavalent ones, are carcinogens, corrosives, delayed contact sensitizers, and have the kidney as their primary target organ. But chromium is also an essential element for humans. The body clearly possesses some effective detoxification mechanisms for some degree of exposure to hexavalent chrome compounds. The significant features of acute and chronic chromium toxicity are presented in view of these considerations.

Environmental exposure to arsenic and chromium in an industrial area

OpenAIRE

Vimercati, Luigi; Gatti, Maria F; Gagliardi, Tommaso; Cuccaro, Francesco; De Maria, Luigi; Caputi, Antonio; Quarato, Marco; Baldassarre, Antonio

2017-01-01

Arsenic and chromium are widespread environmental contaminants that affect global health due to their toxicity and carcinogenicity. To date, few studies have investigated exposure to arsenic and chromium in a population residing in a high-risk environmental area. The aim of this study is to evaluate the exposure to arsenic and chromium in the general population with no occupational exposure to these metals, resident in the industrial area of Taranto, Southern Italy, through biological monitor...

Wet skins tanning with chromium in dense CO2 under pressure

International Nuclear Information System (INIS)

Saldinari, L.; Dutel, Ch.; Perre, Ch.

2000-01-01

An ancestral gesture steadily improved through the centuries, the transformation of skins into leather includes several stages of which the principal one is tanning. Today, 90 % of the world's leather products are tanned with chromium. However, this stage is an environmental liability, and reducing the volume and chromium content of the waste has become a major issue. A first study on skin degreasing by dense CO 2 helped sharply reduce the volume of the fatty effluents. To replace water by dense CO 2 as the tanning medium was the logical next step. The present study was carried out in cooperation with three tanneries in the Rhone-Alpes-Auvergne area of France and a manufacturer of tanning materials. The difficulty of the study was the chemically opposed character of the two media involved. CO 2 is a non-polar and lipophilic solvent while inorganic chromium is insoluble. The water present in the treated skin is a polar and ionic reaction medium and one of the reagents in tanning chemistry. The mixture of these two partially miscible compounds gives a pH 3 by carbonic acid formation. Tanning is based on the reactivity of collagen, the main component of the skin, with hydroxylated complexes of chromium. Collagen is a protein containing some chemical functions, amines (R-NH 2 ) and carboxylic (R-COOH) for example. These functions impart an amphoteric character to the compound. The WERNER theory of complex salts explains the formation of hydroxylated complexes of chromium and their fixing on the carboxylic functions of collagen by oxolation. pH is the key parameter in tanning. The success of the process demands chromium impregnation without fixing it at a pH lower than 5, and then to fix it by increasing the pH. This opened two alternatives for transferring chromium in the skin: solubilize chromium in CO 2 via soluble organometallic complexes; or put the chromium salt into suspension without solubilizing it. The best results were obtained with the second option, which

Substoichiometric determination of chromium by neutron activation analysis

International Nuclear Information System (INIS)

Kudo, K.; Shigematsu, T.; Kobayashi, K.

1977-01-01

A method of radioactivation analysis has been developed for the determination of chromium. It is based on the substoichiometric extraction of chromium diethyldithiocarbamate into methyl-isobutyl-ketone from acetate buffer solution in the presence of EDTA and potassium cyanide. A solution of NaDDC was prepared by dissolving an appropriate amount of GR grade salt in bidistelled water. The concentration of NaDDC was determined by substoichiometric isotope dilution method using 64 Cu or sup(114m)In tracer of known specific activity. The extraction of chromium is not influenced by the presence of EDTA or potassium cyanide while the extraction of chromium is inhibited in tartrate or citrate solution. All metal ions examined are extracted by NaDDC together with chromium and become to interfere for the substoichiometric extraction of chromium. This can be avoided, however, by the addition of EDTA except for copper and silver. The method has been applied for the determination of chromium in high-purity calcium carbonate and NBS glasses as standard reference materials. (T.G.)

Chronic occupational exposure to hexavalent chromium causes DNA damage in electroplating workers.

Science.gov (United States)

Zhang, Xu-Hui; Zhang, Xuan; Wang, Xu-Chu; Jin, Li-Fen; Yang, Zhang-Ping; Jiang, Cai-Xia; Chen, Qing; Ren, Xiao-Bin; Cao, Jian-Zhong; Wang, Qiang; Zhu, Yi-Min

2011-04-12

Occupational exposure to chromium compounds may result in adverse health effects. This study aims to investigate whether low-level hexavalent chromium (Cr(VI)) exposure can cause DNA damage in electroplating workers. 157 electroplating workers and 93 control subjects with no history of occupational exposure to chromium were recruited in Hangzhou, China. Chromium levels in erythrocytes were determined by graphite furnace atomic absorption spectrophotometer. DNA damage in peripheral lymphocytes was evaluated with the alkaline comet assay by three parameters: Olive tail moment, tail length and percent of DNA in the comet tail (tail DNA%). Urinary 8-OHdG levels were measured by ELISA. Chromium concentration in erythrocytes was about two times higher in electroplating workers (median: 4.41 μg/L) than that in control subjects (1.54 μg/L, P electroplating workers. Low-level occupational chromium exposure induced DNA damage.

Bioremediation of chromium in tannery effluent by microbial consortia

African Journals Online (AJOL)

Chromium is the most toxic and common among the heavy metal pollutants of industrial effluents. In the present work the chromium remediation ability of Bacillus subtilis, Pseudomonas aeruginosa and Saccharomyces cerevisiae in consortia and in their immobilized forms was studied and their efficiencies were compared.

Integral alpha and gamma radiation measurements in dwelling houses

International Nuclear Information System (INIS)

Paripas, B.; Takacs, S.; Somogyi, G.; Nikl, I.

1984-01-01

A solid state nuclear track detector method is applied to determine radon and total alpha-exposures (time integral of activity concentrations). The mathematical description of the method of measurement by a passive device equipped with two plastic sheets is presented. Measurements have been carried out in 88 houses over a five-month period and in 20 houses every season for a whole year. Simultaneously with the seasonal measurements of alpha-exposures, the gamma doses were also determined by means of TL dosemeters. The mean exposures due to thoron and its progeny have been estimated by statistical methods. A possible connection between the measured quantities and the lung cancer rates in two settlements were examined. (Author)

Chromium supplementation improved post-stroke brain infarction and hyperglycemia.

Science.gov (United States)

Chen, Wen-Ying; Mao, Frank Chiahung; Liu, Chia-Hsin; Kuan, Yu-Hsiang; Lai, Nai-Wei; Wu, Chih-Cheng; Chen, Chun-Jung

2016-04-01

Hyperglycemia is common after acute stroke and is associated with a worse outcome of stroke. Thus, a better understanding of stress hyperglycemia is helpful to the prevention and therapeutic treatment of stroke. Chromium is an essential nutrient required for optimal insulin activity and normal carbohydrate and lipid metabolism. Beyond its nutritional effects, dietary supplement of chromium causes beneficial outcomes against several diseases, in particular diabetes-associated complications. In this study, we investigated whether post-stroke hyperglycemia involved chromium dynamic mobilization in a rat model of permanent focal cerebral ischemia and whether dietary supplement of chromium improved post-stroke injury and alterations. Stroke rats developed brain infarction, hyperglycemia, hyperinsulinemia, glucose intolerance, and insulin resistance. Post-stroke hyperglycemia was accompanied by elevated secretion of counter-regulatory hormones including glucagon, corticosterone, and norepinephrine, decreased insulin signaling in skeletal muscles, and increased hepatic gluconeogenesis. Correlation studies revealed that counter-regulatory hormone secretion showed a positive correlation with chromium loss and blood glucose increased together with chromium loss. Daily chromium supplementation increased tissue chromium levels, attenuated brain infarction, improved hyperglycemia, and decreased plasma levels of glucagon and corticosterone in stroke rats. Our findings suggest that stroke rats show disturbance of tissue chromium homeostasis with a net loss through urinary excretion and chromium mobilization and loss might be an alternative mechanism responsible for post-stroke hyperglycemia.

Phosphate solubilization and chromium (VI) remediation potential of Klebsiella sp. strain CPSB4 isolated from the chromium contaminated agricultural soil.

Science.gov (United States)

Gupta, Pratishtha; Kumar, Vipin; Usmani, Zeba; Rani, Rupa; Chandra, Avantika

2018-02-01

In this study, an effort was made to identify an efficient phosphate solubilizing bacterial strain from chromium contaminated agricultural soils. Based on the formation of a solubilized halo around the colonies on Pikovskaya's agar amended with chromium (VI), 10 strains were initially screened out. Out of 10, strain CPSB4, which showed significantly high solubilization zone at different chromium concentrations, was selected for further study. The strain CPSB4 showed significant plant growth promotion traits with chromium (VI) stress under in-vitro conditions in broth. The plant growth promotion activities of the strain decreased regularly, but were not completely lost with the increase in concentration of chromium up to 200 mg L -1 . On subjected to FT-IR analysis, the presence of the functional group, indicating the organic acid aiding in phosphate solubilization was identified. At an optimal temperature of 30  ° C and pH 7.0, the strain showed around 93% chromium (VI) reduction under in-vitro conditions in broth study. In soil condition, the maximum chromium (VI) reduction obtained was 95% under in-vitro conditions. The strain CPSB4 was identified as Klebsiella sp. on the basis of morphological, biochemical and 16S rRNA gene sequencing. This study shows that the diverse role of the bacterial strain CPSB4 would be useful in the chromium contaminated soil as a good bioremediation and plant growth promoting agent as well. Copyright © 2017 Elsevier Ltd. All rights reserved.

Intracellular chromium localization and cell physiological response in the unicellular alga Micrasterias

Science.gov (United States)

Volland, Stefanie; Lütz, Cornelius; Michalke, Bernhard; Lütz-Meindl, Ursula

2012-01-01

Various contaminants like metals and heavy metals are constantly released into the environment by anthropogenic activities. The heavy metal chromium has a wide industrial use and exists in two stable oxidation states: trivalent and hexavalent. Chromium can cause harm to cell metabolism and development, when it is taken up by plants instead of necessary micronutrients such as for example iron. The uptake of Cr VI into plant cells has been reported to be an active process via carriers of essential anions, while the cation Cr III seems to be taken up inactively. Micrasterias denticulata, an unicellular green alga of the family Desmidiaceae is a well-studied cell biological model organism. Cr III and VI had inhibiting effects on its cell development, while cell division rates were only impaired by Cr VI. Transmission electron microscopy (TEM) revealed ultrastructural changes such as increased vacuolization, condensed cytoplasm and dark precipitations in the cell wall after 3 weeks of Cr VI treatment. Electron energy loss spectroscopy (EELS) and electron spectroscopic imaging (ESI) were applied to measure intracellular chromium distribution. Chromium was only detected after 3 weeks of 10 μM Cr VI treatment in electron dense precipitations found in bag-like structures along the inner side of the cell walls together with iron and elevated levels of oxygen, pointing toward an accumulation respectively extrusion of chromium in form of an iron–oxygen compound. Atomic emission spectroscopy (EMS) revealed that Micrasterias cells are able to accumulate considerable amounts of chromium and iron. During chromium treatment the Cr:Fe ratio shifted in favor of chromium, which implied that chromium may be taken up instead of iron. Significant and rapid increase of ROS production within the first 5 min of treatment confirms an active Cr VI uptake. SOD and CAT activity after Cr VI treatment did not show a response, while the glutathione pool determined by immuno-TEM decreased

Intracellular chromium localization and cell physiological response in the unicellular alga Micrasterias

Energy Technology Data Exchange (ETDEWEB)

Volland, Stefanie, E-mail: Stefanie.Volland@stud.sbg.ac.at [Plant Physiology Division, Cell Biology Department, University of Salzburg, Hellbrunnerstr 34, 5020 Salzburg (Austria); Luetz, Cornelius, E-mail: cornelius.luetz@uibk.ac.at [Institute of Botany, University of Innsbruck, Sternwartestrasse 15, 6020 Innsbruck (Austria); Michalke, Bernhard, E-mail: bernhard.michalke@helmholtz-muenchen.de [Helmholtz Zentrum Muenchen, German Research Centre for Environmental Health, Institute of Ecological Chemistry, Ingolstaedter Landstrasse 1, 85764 Neuherberg (Germany); Luetz-Meindl, Ursula, E-mail: ursula.luetz-meindl@sbg.ac.at [Plant Physiology Division, Cell Biology Department, University of Salzburg, Hellbrunnerstr 34, 5020 Salzburg (Austria)

2012-03-15

Various contaminants like metals and heavy metals are constantly released into the environment by anthropogenic activities. The heavy metal chromium has a wide industrial use and exists in two stable oxidation states: trivalent and hexavalent. Chromium can cause harm to cell metabolism and development, when it is taken up by plants instead of necessary micronutrients such as for example iron. The uptake of Cr VI into plant cells has been reported to be an active process via carriers of essential anions, while the cation Cr III seems to be taken up inactively. Micrasterias denticulata, an unicellular green alga of the family Desmidiaceae is a well-studied cell biological model organism. Cr III and VI had inhibiting effects on its cell development, while cell division rates were only impaired by Cr VI. Transmission electron microscopy (TEM) revealed ultrastructural changes such as increased vacuolization, condensed cytoplasm and dark precipitations in the cell wall after 3 weeks of Cr VI treatment. Electron energy loss spectroscopy (EELS) and electron spectroscopic imaging (ESI) were applied to measure intracellular chromium distribution. Chromium was only detected after 3 weeks of 10 {mu}M Cr VI treatment in electron dense precipitations found in bag-like structures along the inner side of the cell walls together with iron and elevated levels of oxygen, pointing toward an accumulation respectively extrusion of chromium in form of an iron-oxygen compound. Atomic emission spectroscopy (EMS) revealed that Micrasterias cells are able to accumulate considerable amounts of chromium and iron. During chromium treatment the Cr:Fe ratio shifted in favor of chromium, which implied that chromium may be taken up instead of iron. Significant and rapid increase of ROS production within the first 5 min of treatment confirms an active Cr VI uptake. SOD and CAT activity after Cr VI treatment did not show a response, while the glutathione pool determined by immuno-TEM decreased

Intracellular chromium localization and cell physiological response in the unicellular alga Micrasterias

International Nuclear Information System (INIS)

Volland, Stefanie; Lütz, Cornelius; Michalke, Bernhard; Lütz-Meindl, Ursula

2012-01-01

Various contaminants like metals and heavy metals are constantly released into the environment by anthropogenic activities. The heavy metal chromium has a wide industrial use and exists in two stable oxidation states: trivalent and hexavalent. Chromium can cause harm to cell metabolism and development, when it is taken up by plants instead of necessary micronutrients such as for example iron. The uptake of Cr VI into plant cells has been reported to be an active process via carriers of essential anions, while the cation Cr III seems to be taken up inactively. Micrasterias denticulata, an unicellular green alga of the family Desmidiaceae is a well-studied cell biological model organism. Cr III and VI had inhibiting effects on its cell development, while cell division rates were only impaired by Cr VI. Transmission electron microscopy (TEM) revealed ultrastructural changes such as increased vacuolization, condensed cytoplasm and dark precipitations in the cell wall after 3 weeks of Cr VI treatment. Electron energy loss spectroscopy (EELS) and electron spectroscopic imaging (ESI) were applied to measure intracellular chromium distribution. Chromium was only detected after 3 weeks of 10 μM Cr VI treatment in electron dense precipitations found in bag-like structures along the inner side of the cell walls together with iron and elevated levels of oxygen, pointing toward an accumulation respectively extrusion of chromium in form of an iron–oxygen compound. Atomic emission spectroscopy (EMS) revealed that Micrasterias cells are able to accumulate considerable amounts of chromium and iron. During chromium treatment the Cr:Fe ratio shifted in favor of chromium, which implied that chromium may be taken up instead of iron. Significant and rapid increase of ROS production within the first 5 min of treatment confirms an active Cr VI uptake. SOD and CAT activity after Cr VI treatment did not show a response, while the glutathione pool determined by immuno-TEM decreased

Fluctuation characteristics of solar radiation in crop cultivation

International Nuclear Information System (INIS)

Hayashi, S.; Suzuki, H.

1996-01-01

The objective of this study was to clarify the fluctuation of solar radiation for long and short periods, which is very crucial for plant growth. Data obtained from a meteorological observatory were used to investigate solar radiation and sunshine duration for a long period. For a short period, observation of global solar radiation and sky solar radiation were conducted in a glass house and at an open field. (1) Yearly average percentage of solar radiation at Kagawa from 1973 to 1994 was 44.3%, and its coefficient of variation was 3.9%. The percentage of possible sunshine and the coefficient were larger than those of solar radiation, 47.3% and 56% respectively. (2) Percentage of possible solar radiation and percentage of possible sunshine showed seasonal variation. Those coefficients of variation both increased exponentially with cloud amount. (3) Variations of global solar radiation and direct solar radiation were more remarkable in the glass house than those in the open field, while variations of sky solar radiation were small in the house and at the open field. (4) The fluctuation of solar radiation observed every 5 minutes was presented as the difference of radiation, present value minus the preceding value. The difference was positive in the morning, negative in the afternoon at the open field. In the house both positive and negative values were obtained the whole day. (5) Diurnal variation of ratio of direct solar radiation to sky solar radiation showed a parabolic effect, whereas it had irregular and large fluctuations at the open field

Electrothermal Vaporization-QQQ-ICP-MS for Determination of Chromium in Mainstream Cigarette Smoke Particulate.

Science.gov (United States)

Fresquez, Mark R; Gonzalez-Jimenez, Nathalie; Gray, Naudia; Valentin-Blasini, Liza; Watson, Clifford H; Pappas, R Steven

2017-05-01

Chromium is transported in mainstream tobacco smoke at very low concentrations. However, when chromium is deposited too deeply in the lungs for mucociliary clearance, or is in a particle that is too large to pass directly through tissues, it bioaccumulates in the lungs of smokers. It is important to determine the concentrations of chromium that are transported in mainstream smoke. Several reliable studies have resulted in reports of chromium concentrations in smoke particulate that were below limits of detection (LODs) for the instruments and methods employed. In this study, electrothermal vaporization-triple quad-inductively coupled plasma-mass spectrometry (ETV-QQQ-ICP-MS) was chosen for determination of chromium concentrations in mainstream smoke because of the high sensitivity of ETV combined with QQQ-ICP-MS. The smoke from five reference, quality control, and commercial cigarettes was analyzed using ETV-QQQ-ICP-MS with isotope dilution for quantitative determination of chromium. The method LOD was sufficiently low that chromium concentrations in mainstream smoke could indeed be determined. The chromium concentrations in the smoke particulate were between 0.60 and 1.03 ng/cigarette. The range of chromium concentrations was at or below previously reported LODs. Determination of the oxidation state of the chromium transported in mainstream smoke would also be important, in consideration of the fact that both chromium(III) and chromium(VI) oxidation states cause inhalation toxicity, but chromium(VI) is also a carcinogen. It was possible to separate the oxidation states using ETV-QQQ-ICP-MS. However, determination of individual species at the levels found in mainstream smoke particulate matter was not possible with the present method. Published by Oxford University Press 2017. This work is written by (a) US Government employee(s) and is in the public domain in the US.

Bacillus species enhance growth parameters of chickpea (Cicer arietinum L.) in chromium stressed soils.

Science.gov (United States)

Wani, Parvaze Ahmad; Khan, Mohammad Saghir

2010-11-01

Pollution of the agricultural land by the toxic chromium is a global threat that has accelerated dramatically since the beginning of industrial revolution. Toxic chromium affects both the microbial diversity as well as reduces the growth of the plants. Understanding the effect of the chromium reducing and plant growth promoting rhizobacteria on chickpea crop will be useful. Chromium reducing and plant growth promoting Bacillus species PSB10 significantly improved growth, nodulation, chlorophyll, leghaemoglobin, seed yield and grain protein of chickpea crop grown in the presence of different concentrations of chromium compared to the plants grown in the absence of bio-inoculant. The strain also reduced the uptake of chromium in roots, shoots and grains of chickpea crop compared to plants grown in the absence of bio-inoculant. This study thus suggested that the Bacillus species PSB10 due to its intrinsic abilities of growth promotion and attenuation of the toxic effects of chromium could be exploited for remediation of chromium from chromium contaminated sites. Copyright © 2010 Elsevier Ltd. All rights reserved.

Ductile-brittle transition of thoriated chromium.

Science.gov (United States)

Wilcox, B. A.; Veigel, N. D.; Clauer, A. H.

1972-01-01

Unalloyed chromium and chromium containing approximately 3 wt % ThO2 were prepared from powder produced by a chemical vapor deposition process. When rolled to sheet and tested in tension, it was found that the thoriated material had a lower ductile-to-brittle transition temperature (DBTT) than unalloyed chromium. This ductilizing was evident both in the as-rolled condition and after the materials had been annealed for 1 hour at 1200 C. The improved ductility in thoriated chromium may be associated with several possible mechanisms: (1) particles may disperse slip, such that critical stress or strain concentrations for crack nucleation are more difficult to achieve; (2) particles may act as dislocation sources, thus providing mobile dislocations in this normally source-poor material, in a manner similar to prestraining; and (3) particles in grain boundaries may help to transmit slip across the boundaries, thus relieving stress concentrations and inhibiting crack nucleation.

Anthropogenic Chromium Emissions in China from 1990 to 2009

Science.gov (United States)

Cheng, Hongguang; Zhou, Tan; Li, Qian; Lu, Lu; Lin, Chunye

2014-01-01

An inventory of chromium emission into the atmosphere and water from anthropogenic activities in China was compiled for 1990 through to 2009. We estimate that the total emission of chromium to the atmosphere is about 1.92×105t. Coal and oil combustion were the two leading sources of chromium emission to the atmosphere in China, while the contribution of them showed opposite annual growth trend. In total, nearly 1.34×104t of chromium was discharged to water, mainly from six industrial categories in 20 years. Among them, the metal fabrication industry and the leather tanning sector were the dominant sources of chromium emissions, accounting for approximately 68.0% and 20.0% of the total emissions and representing increases of15.6% and 10.3% annually, respectively. The spatial trends of Cr emissions show significant variation based on emissions from 2005 to 2009. The emission to the atmosphere was heaviest in Hebei, Shandong, Guangdong, Zhejiang and Shanxi, whose annual emissions reached more than 1000t for the high level of coal and oil consumption. In terms of emission to water, the largest contributors were Guangdong, Jiangsu, Shandong and Zhejiang, where most of the leather production and metal manufacturing occur and these four regions accounted for nearly 47.4% of the total emission to water. PMID:24505309

FP corrosion dependence on carbon and chromium content in Fe-Cr steel

International Nuclear Information System (INIS)

Sasaki, Koei; Tanigaki, Takanori; Fukumoto, Ken-ichi; Uno, Masayoshi

2015-01-01

In an attempt to investigate Cs or Cs-Te corrosion dependence on chromium or carbon content in Fe-Cr steel, cesium and Cs-Te corrosion test were performed to three specimens, Fe-9Cr-0C, Fe-9Cr-0.14C and Fe-13Cr-0.14C, for 100 hours at 973K in simulated high burn-up fuel pin environment. Cesium corrosion depth has no dependence on chromium or carbon content in Fe-Cr steel. Cs-Te corrosion was appeared in only Fe-13Cr-0.14C which has chromium carbides ranged along grain boundary. Appearance of the Cs-Te corrosion was determined by distribution or arrangement of chromium carbides which depends on chromium and carbon content. (author)

Effective bioleaching of chromium in tannery sludge with an enriched sulfur-oxidizing bacterial community.

Science.gov (United States)

Zeng, Jing; Gou, Min; Tang, Yue-Qin; Li, Guo-Ying; Sun, Zhao-Yong; Kida, Kenji

2016-10-01

In this study, a sulfur-oxidizing community was enriched from activated sludge generated in tannery wastewater treatment plants. Bioleaching of tannery sludge containing 0.9-1.2% chromium was investigated to evaluate the effectiveness of the enriched community, the effect of chromium binding forms on bioleaching efficiency, and the dominant microbes contributing to chromium bioleaching. Sludge samples inoculated with the enriched community presented 79.9-96.8% of chromium leaching efficiencies, much higher than those without the enriched community. High bioleaching efficiencies of over 95% were achieved for chromium in reducible fraction, while 60.9-97.9% were observed for chromium in oxidizable and residual fractions. Acidithiobacillus thiooxidans, the predominant bacteria in the enriched community, played an important role in bioleaching, whereas some indigenous heterotrophic species in sludge might have had a supporting role. The results indicated that A. thiooxidans-dominant enriched microbial community had high chromium bioleaching efficiency, and chromium binding forms affected the bioleaching performance. Copyright © 2016 Elsevier Ltd. All rights reserved.

Chromium base high performance materials: Where and how do they come from?

Science.gov (United States)

Choi, In-Kap

1996-08-01

The origin of chromium base performance materials (CBPM) is described. CBPM may include (1) trivalent chromium chemicals such as chromic acetate, chromic chloride, chromic bromide, chromic fluoride, chromic iodide, chromic phosphate, and chromic sulfate; (2) hexavalent chromium chemicals such as chromic acid, lithium chromate, sodium chromate, sodium dichromate, and potassium dichromate; (3) oxide forms of chromium such as black chrome, chromium dioxide, chromium oxide, and chromium hydroxide; and (4) other chromium compounds such as chromium aluminide, chromium boride, chromium carbide, chromium molybdate, chromium nitride, chromium silicide, chromium tungstate and lanthanum chromite. Extensive reviews of production processes, properties, and applications/end uses of CBPM are made.

21 CFR 73.3111 - Chromium oxide greens.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium oxide greens. 73.3111 Section 73.3111... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Medical Devices § 73.3111 Chromium oxide greens. (a) Identity and specifications. The color additive chromium oxide greens (chromic oxide) (CAS Reg. No. 1308-38-9...

THE ESTROGENS / CHROMIUM INTERACTION IN THE NITRIC OXIDE GENERATION.

Science.gov (United States)

Sawicka, Ewa; Piwowar, Agnieszka; Musiala, Tomasz; Dlugosz, Anna

2017-05-01

The interaction of estrogens with environmental toxins in free radicals generation: reactive oxygen species (ROS) or reactive nitrogen species (RNS) which participates in cancerogenesis is not yet recognized. Chromium(VI) is widely present in environment. One of its toxicity pathway is free radicals generation. Estrogens have the ability to scavenge free radicals, but may also act as prooxidants. Both chromium(VI) and estrogens are classified by International Agency for Research on Cancer (IARC) as carcinogens, so synergistic effect seems very dangerous. The interaction of chromium and estrogens in ROS generation are partly described but there are no reports on estrogen/chromium interaction on nitric oxide (NO) generation. The aim of the study was to examine the interaction of chromium(VI) and 17-p-estradiol (E2) on NO level in human blood as well as the role of E2 metabolites: 4-hydroxyestradiol (4-OHE2) and 16a-hydroxyestrone (16α-OHE1) in these processes. The NO level was estimated with the diagnostic kit (Nitric Oxide Colorimetric Detection Kit from Arbor Assays) in human blood in vitm. The results showed that Cr(VI) in used concentration (0.5; 1.0 and 5.0 gg/mL) decreases significantly NO level in blood, acting antagonistically to E2 and 4-OHE2. Estrogens (E2, 4-OHE2 and 16α-OHEI) do not protect against inhibiting effect of Cr(VI) on nitric oxide generation in blood because after combined exposure the decreased production of NO in blood was noted. In conclusion, presented results provide the information about the character of estrogen/Cr(VI) interaction in NO level in human blood. It is important knowledge for cardio protected effect e.g., hormone replacement therapy in environmental or occupational exposure to Cr(VI), chromium supplementation, also important for cancer risk evaluation.

Activation of bentonite to remove the chromium from waste water produced by panning industry, and studying the chromium recovery efficiency

International Nuclear Information System (INIS)

Abbasi, S.; Wahba, H.; AL-Masri, M.S.

2010-01-01

The fast development of tanning industry led to an increase in environmental problems resulting from discharging its wastes to the surrounding environment. Thus solving this problem became one of the most important aims that the researchers work on. The chromium content of the industrial water wastes of the tanning industry considered as the main pollutant for the environment. The Aleppo Bentonite is used in early research to remove the chromium from the industrial waste water.The current research aims to find a method to activate the Aleppo Bentonite in order to increase the effective removal of chromium from the industrial waste water which is produced by tanning industry, as well as to specify the optimal conditions for chromium recovery.This study used the Aleppo Bentonite, whose origin is Tal Ajar-Aleppo to study the activation aspects using Sulfuric Acid, Hydrochloric Acid and Nitric Acid, in addition to study the recovery aspects using the same acids and hydrogen peroxide and to specify the optimal conditions for chromium recovery through applying some experiments based on three main factors: concentration, settling time and temperature.It was observed from the applied experiments that it is possible to recover chromium from Bentonite efficiently up to (80% - 90%) by treating the Bentonite with hydrogen peroxide(33% concentration) at room temperature, or by treating it with hydrogen peroxide(8.25% concentration) at 75 o C, while the settling time factor proved that full recovery of chromium is obtained during the first hour, and increasing the time factor does not affect the efficiency of chromium recovery. (author)

Detergents and bleaches are sources of chromium contact dermatitis in Israel

DEFF Research Database (Denmark)

Ingber, A; Gammelgaard, Bente; David, M

1998-01-01

Total chromium levels were determined in 38 detergents and 12 bleaches on the market in Israel (45 locally produced, 5 imported). The samples were analyzed by Zeeman-corrected graphite furnace atomic absorption spectrophotometry. Chromium levels were higher than 5 ppm in 28 (56%) of the 50 products...... ppm, it is concluded that these consumer products may be the cause of the high incidence of chromium sensitivity in Israel....

Preliminary X-ray crystallographic analysis of SMU.573, a putative sugar kinase from Streptococcus mutans

Energy Technology Data Exchange (ETDEWEB)

Zhou, Yan-Feng; Li, Lan-Fen [National Laboratory of Protein Engineering and Plant Genetic Engineering, College of Life Sciences, Peking University, Beijing 100871 (China); Yang, Cheng [National Laboratory of Protein Engineering and Plant Genetic Engineering, College of Life Sciences, Peking University, Beijing 100871 (China); Rigaku/MSC Inc., 9009 New Trails Drive, The Woodlands, TX 77381 (United States); Liang, Yu-He, E-mail: liangyh@pku.edu.cn [National Laboratory of Protein Engineering and Plant Genetic Engineering, College of Life Sciences, Peking University, Beijing 100871 (China); Su, Xiao-Dong, E-mail: liangyh@pku.edu.cn [National Laboratory of Protein Engineering and Plant Genetic Engineering, College of Life Sciences, Peking University, Beijing 100871 (China); Shenzhen Graduate School of Peking University, Shenzhen 518055 (China)

2008-01-01

SMU.573 from S. mutans was expressed in E. coli and crystallized. The crystals belong to space group I4 and 2.5 Å resolution diffraction data were collected at an in-house chromium radiation source. SMU.573 from Streptococcus mutans is a structurally and functionally uncharacterized protein that was selected for structural biology studies. Native and SeMet-labelled proteins were expressed with an N-His tag in Escherichia coli BL21 (DE3) and purified by Ni{sup 2+}-chelating and size-exclusion chromatography. Crystals of the SeMet-labelled protein were obtained by the hanging-drop vapour-diffusion method and a 2.5 Å resolution diffraction data set was collected using an in-house chromium radiation source. The crystals belong to space group I4, with unit-cell parameters a = b = 96.53, c = 56.26 Å, α = β = γ = 90°.

Preliminary X-ray crystallographic analysis of SMU.573, a putative sugar kinase from Streptococcus mutans

International Nuclear Information System (INIS)

Zhou, Yan-Feng; Li, Lan-Fen; Yang, Cheng; Liang, Yu-He; Su, Xiao-Dong

2007-01-01

SMU.573 from S. mutans was expressed in E. coli and crystallized. The crystals belong to space group I4 and 2.5 Å resolution diffraction data were collected at an in-house chromium radiation source. SMU.573 from Streptococcus mutans is a structurally and functionally uncharacterized protein that was selected for structural biology studies. Native and SeMet-labelled proteins were expressed with an N-His tag in Escherichia coli BL21 (DE3) and purified by Ni 2+ -chelating and size-exclusion chromatography. Crystals of the SeMet-labelled protein were obtained by the hanging-drop vapour-diffusion method and a 2.5 Å resolution diffraction data set was collected using an in-house chromium radiation source. The crystals belong to space group I4, with unit-cell parameters a = b = 96.53, c = 56.26 Å, α = β = γ = 90°

[Research on the application of in-situ biological stabilization solidification technology in chromium contaminated site management].

Science.gov (United States)

Zhang, Jian-rong; Li, Juan; Xu, Wei

2013-09-01

In-situ biological stabilization solidification (SS) technology is an effective ground water risk control method for chromium contaminated sites. Through on-site engineering test, this paper has preliminarily validated the remediation effect of in-situ SS method on a southern chromium contaminated site. The engineering test site has an area of approximately 600 m2, and is located at the upstream of the contaminated area. Due to the severe contamination of chromium, the total chromium concentration reached up to 11,850 mg x kg(-1), while the hexavalent chromium concentration reached up to 349 mg x kg(-1), and the most severely contaminated soil had a depth of -0.5 - -2 m. Variations in hexavalent chromium and total chromium concentration in groundwater were observed through the injection of reducing agents and microbial regulators into the injection wells in the test site, and through the monitoring analysis at different time and different depth under the action of the injection agents. Results of the engineering test showed that the on-site SS technology significantly changed the chromium speciation in soil and then reduced the migration of chromium, thus the groundwater risk was reduced. The injected agents had a good effect of hexavalent chromium remediation in groundwater within the effective range of the injection wells, and the SS rate of hexavalent chromium into trivalent chromium reached 94%-99.9%, the SS rate of total chromium fixation reached 83.9%-99.8%. The test results are of significant reference value for the remediation of contaminated sites with features of shallow groundwater depth and soil mainly consisting of silty clay and sandy clay.

Thermodynamic properties of chromium bearing slags and minerals. A review

Energy Technology Data Exchange (ETDEWEB)

Xiao Yanping; Holappa, L.

1996-12-31

In this report, the thermodynamic properties of chromium bearing slags and minerals were reviewed based on the available information in the literature. It includes the analysing methods for oxidation state of chromium in slags, oxidation state of chromium and activities of chromium oxides in slags and minerals. The phase diagrams of chromium oxide systems and chromium distributions between slag and metal phases are also covered ill this review. Concerning the analysing methods, it was found that most of the available approaches are limited to iron free slag systems and the sample preparation is very sensitive to the analysing results. In silicate slags under reducing atmosphere, divalent and trivalent chromium co-exist in the slags. It is agreed that the fraction of divalent chromium to total chromium increases with higher temperature, lower slag basicity and oxygen potential. For the slags under oxidising atmosphere, trivalent, pentavalent and hexavalent states were reported to be stable. The activities of CrO and CrO{sub 1.5} were concluded to have positive deviation from ideal solution. Slag basicity has a positive effect and temperature has a negative effect on the activities of chromium oxides. The phase diagrams of the Cr-O, binary, and ternary chromium containing oxide systems have been examined systematically. The analysis shows that the data on the quaternary and quinary systems are insufficient, and require further investigation. The most important features of the chromium containing silicate slags are the large miscibility gaps and the stability of the chromite spinel. (orig.) (76 refs.)

Serum chromium concentrations in type 2 diabetic patients attending ...

African Journals Online (AJOL)

A highly refined diet that contains too few micronutrients has been recognized as the dominant factor in the rising incidence of diabetes and other insulin related conditions. Among the missing micronutrients, chromium has the greatest impact on insulin response. The objective of this study was to determine serum chromium ...

Electrochemistry of chromium(0)-aminocarbene complexes

International Nuclear Information System (INIS)

Hoskovcova, Irena; Rohacova, Jana; Meca, Ludek; Tobrman, Tomas; Dvorak, Dalimil; Ludvik, Jiri

2005-01-01

Two series of chromium(0)-(aryl)aminocarbene complexes substituted on the ligand phenyl ring were prepared and electrochemically investigated: pentacarbonyl((N,N-dimethylamino)(phenyl)carbene(chromium(0) (Ia-e) and chelated tetracarbonyl((η 2 -N-allyl-N-allylamino)(phenyl)carbene(chromium(0) (IIa, c-e). For comparison, a tungsten analogue of IIc (III) and a chromium chelate bearing a methyl substituent instead of the phenyl group IV were taken into the study. The intramolecular interactions of p-substituents on the ligand phenyl ring with the reduction and oxidation centres of the molecule of complex (followed electrochemically using LFER [P. Zuman, Substituent Effects in Organic Polarography, Plenum Press, New York, 1967]) enabled to localize the corresponding electron transfer. The influence of the type of coordination, the substituent on the ligand phenyl ring and the central metal atom on oxidation and reduction potentials is discussed

21 CFR 73.1327 - Chromium oxide greens.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium oxide greens. 73.1327 Section 73.1327... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1327 Chromium oxide greens. (a) Identity. (1) The color additive chromium oxide greens is principally chromic sesquioxide (Cr2O3). (2) Color additive...

Improvement on simultaneous determination of chromium species in aqueous solution by ion chromatography and chemiluminescence detection

DEFF Research Database (Denmark)

Gammelgaard, Bente; Liao, Y.P.; Jons, O.

1997-01-01

A sensitive method for the simultaneous determination of chromium(III) and chromium(VI) was chromatography and chemiluminescence detection. Two Dionex ion-exchange guard columns in series, CG5 and AG7, were used to separate chromium(III) from chromium(VI). Chromium(VI) was reduced by potassium......, the stabilities of reductant and luminol solutions were studied. The linear range of the calibration curve for chromium(III) and chromium(VI) was 1-400 mu g l(-1). The detection limit was 0.12 mu g l(-1) for chromium(III) and 0.09 mu g l(-1) for chromium(VI), respectively. The precision at the 20 mu g l(-1) level...... was 1.4% for chromium(III) and 2.5% for chromium(VI), respectively. The accuracy of the chromium(III) determination was determined by analysis of the NIST standard reference material 1643c, Trace elements in water with the result 19.1 +/- 1.0 mu g Cr(III) l(-1) (certified value 19.0 +/- 0.6 mu g Cr...

Preparation and Characterization of Plasma-Sprayed Ultrafine Chromium Oxide Coatings

International Nuclear Information System (INIS)

Lin Feng; Jiang Xianliang; Yu Yueguang; Zeng Keli; Ren Xianjing; Li Zhenduo

2007-01-01

Ultrafine chromium oxide coatings were prepared by plasma spraying with ultrafine feedstock. Processing parameters of plasma spraying were optimized. Optical microscope (OM) was used to observe the microstructure of the ultrafine chromium oxide coatings. Scanning electron microscopy (SEM) was used to observe the morphology and particle size of ultrafine powder feedstock as well as to examine the microstructure of the chromium oxide coating. In addition, hardness and bonding strength of the ultrafine chromium oxide coatings were measured. The results showed that the optimized plasma spraying parameters were suitable for ultrafine chromium oxide coating and the properties and microstructure of the optimized ultrafine chromium oxide coating were superior compared to conventional chromium oxide wear resistant coatings

21 CFR 73.1326 - Chromium hydroxide green.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium hydroxide green. 73.1326 Section 73.1326... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1326 Chromium hydroxide green. (a) Identity. (1) The color additive chromium hydroxide green is principally hydrated chromic sesquioxide (Cr2O3·XH2O...

The enriched chromium neutrino source for GALLEX

International Nuclear Information System (INIS)

Hartmann, F.X.; Hahn, R.L.

1991-01-01

The preparation and study of an intense source of neutrinos in the form of neutron irradiated materials which are enriched in Cr-50 for use in the GALLEX solar neutrino experiment are discussed. Chromyl fluoride gas is enriched in the Cr-50 isotope by gas centrifugation and subsequently converted to a very stable form of chromium oxide. The results of neutron activation analyses of such chromium samples indicate low levels of any long-lived activities, but show that short-lived activities, in particular Na-24, may be of concern. These results show that irradiating chromium oxide enriched in Cr-50 is preferable to irradiating either natural chromium or argon gas as a means of producing a neutrino source to calibrate the GALLEX detector. These results of the impurity level analysis of the enriched chromyl fluoride gas and its conversion to the oxide are also of interest to work in progress by other members of the Collaboration investigating an alternative conversion of the enriched gas to chromium metal. 35 refs., 12 figs., 5 tabs

Ferrate treatment for removing chromium from high-level radioactive tank waste.

Science.gov (United States)

Sylvester, P; Rutherford, L A; Gonzalez-Martin, A; Kim, J; Rapko, B M; Lumetta, G J

2001-01-01

A method has been developed for removing chromium from alkaline high-level radioactive tank waste. Removing chromium from these wastes is critical in reducing the volume of waste requiring expensive immobilization and deep geologic disposition. The method developed is based on the oxidation of insoluble chromium(III) compounds to soluble chromate using ferrate. This method could be generally applicable to removing chromium from chromium-contaminated solids, when coupled with a subsequent reduction of the separated chromate back to chromium(III). The tests conducted with a simulated Hanford tank sludge indicate that the chromium removal with ferrate is more efficient at 5 M NaOH than at 3 M NaOH. Chromium removal increases with increasing Fe(VI)/Cr(II) molar ratio, but the chromium removal tends to level out for Fe(VI)/ Cr(III) greaterthan 10. Increasingtemperature leadsto better chromium removal, but higher temperatures also led to more rapid ferrate decomposition. Tests with radioactive Hanford tank waste generally confirmed the simulant results. In all cases examined, ferrate enhanced the chromium removal, with a typical removal of around 60-70% of the total chromium present in the washed sludge solids. The ferrate leachate solutions did not contain significant concentrations of transuranic elements, so these solutions could be disposed as low-activity waste.

Effect of compost and humic acid in mobility and concentration of cadmium and chromium in soil and plant

Directory of Open Access Journals (Sweden)

A. Chaab

2016-12-01

Full Text Available The effect of compost and humic acid in mobility and concentration of cadmium and chromium in contaminated soil were investigated. Experiment was carried out with three levels of soil cadmium and chromium and two organic matters (compost and humic acid. The study was performed in a randomized complete block design with 3 replicates. Results indicated that application of organic substances enhanced movement of cadmium and chromium in soil column. Humic acid is more effective than compost on the mobility of cadmium and chromium in soil. Mobility of cadmium and chromium in the lower depths of soil column were increased. Cadmium and chromium concentration in shoots and roots enhanced due to increasing those concentration in soil and application of organic substances. Increase in cadmium in shoots can be attributed to the high mobility of this element in maize plant. Maize root chromium concentration was greater than shoot chromium concentration. Humic acid was more effective than compost as cadmium and chromium concentration in root and shoot was concerned. Low mobility of chromium in plant and accumulation of chromium in roots can be reasons of decreasing of chromium concentration in shoot of plant and its bioaccumulation.

Study on chromium speciation in rats by the isotope tracer technique

International Nuclear Information System (INIS)

Feng Weiyue; Qian Qinfang; Ding Wenjun; Chai Zhifang

1999-01-01

The chromium speciation in the liver cytosol fraction, serum and urine of both normal and diabetic rats are studied by the enriched stable isotope tracer technique combined with the get chromatography and the neutron activating analysis (NAA). The results are as follows: (1) When Cr(III) enters the animal body, it is most likely to be combined with serum proteins. The chromium-protein compound acts as a carrier to transport Cr to the whole body. In the liver cytosol fraction, Cr (III) is also mainly combined with the high molecular weight protein and retains as chromium-protein substance in the liver. (2) A low molecular weight chromium-containing compound is found in all the liver cell cytosol fraction, serum and urine of the two group rats. (3) The diabetic rats lose more amount of low molecular weight of chromium compound in urine than the normal rats do. This might be a main reason to explain why the diabetic rats retain lower Cr in their bodies than the normal group

Chromium Chemistry in the Subsurface

Science.gov (United States)

Chromium (VI) (Cr) is carcinogenic and a threat to human and ecological health. There are adequate and acceptable methods to characterize and assess Cr contaminated sites. Cr chemistry in the environment is well understood. There are documented methods to address Cr contaminat...

Carcinogenicity of chromium and chemoprevention: a brief update

Directory of Open Access Journals (Sweden)

Wang Y

2017-08-01

Full Text Available Yafei Wang,1,* Hong Su,1,* Yuanliang Gu,1 Xin Song,1 Jinshun Zhao1,2 1Department of Preventative Medicine, Zhejiang Key Laboratory of Pathophysiology, School of Medicine, Ningbo University, Ningbo, People’s Republic of China; 2Toxicology and Molecular Biology Branch, Health Effects Laboratory Division, National Institute for Occupational Safety and Health, Morgantown, WV, USA *These authors contributed equally to this work Abstract: Chromium has two main valence states: hexavalent chromium (Cr[VI] and trivalent chromium (Cr[III]. Cr(VI, a well-established human carcinogen, can enter cells by way of a sulfate/phosphate anion-transport system, and then be reduced to lower-valence intermediates consisting of pentavalent chromium (Cr[V], tetravalent chromium (Cr[IV] or Cr(III via cellular reductants. These intermediates may directly or indirectly result in DNA damage or DNA–protein cross-links. Although Cr(III complexes cannot pass easily through cell membranes, they have the ability to accumulate around cells to induce cell-surface morphological alteration and result in cell-membrane lipid injuries via disruption of cellular functions and integrity, and finally to cause DNA damage. In recent years, more research, including in vitro, in vivo, and epidemiological studies, has been conducted to evaluate the genotoxicity/carcinogenicity induced by Cr(VI and/or Cr(III compounds. At the same time, various therapeutic agents, especially antioxidants, have been explored through in vitro and in vivo studies for preventing chromium-induced genotoxicity/carcinogenesis. This review aims to provide a brief update on the carcinogenicity of Cr(VI and Cr(III and chemoprevention with different antioxidants. Keywords: hexavalent chromium, Cr(VI, trivalent chromium, Cr(III, genotoxicity, carcinogenicity, chemoprevention, antioxidant 

Crossover and valence band Kβ X-rays of chromium oxides

International Nuclear Information System (INIS)

Fazinic, Stjepko; Mandic, Luka; Kavcic, Matjaz; Bozicevic, Iva

2011-01-01

Kβ X-ray spectra of chromium metal and selected chromium oxides were measured twice using medium resolution flat crystal spectrometer and high resolution spectrometer employing Johansson geometry after excitation with 2 MeV proton beams. The positions and intensities of crossover (Kβ'') and valence (Kβ 2,5 ) band X-rays relative to the primary Kβ X-ray components were extracted in a consistent way. The results were compared with the existing data obtained by proton and photon induced ionization mechanisms and theoretical predictions. The obtained results in peak relative positions and intensities were analyzed in order to study dependence on the chromium oxidation states and chromium-oxygen bond lengths in selected chromium oxides. Our results obtained by both spectrometers confirm that the linear trend observed for the valence peak relative energy shift as a function of chromium oxidation number does not depend on the experimental resolution. Experimental results for normalized intensities (i.e. relative intensities divided with the number of chromium-oxygen pairs) of crossover and valence band X-rays obtained by both spectrometers are in very good agreement, and follow exponential relationship with the average Cr-O bond lengths in corresponding chromium oxides. The observed trends in crossover and valence X-rays normalized intensities could be used to measure the average chromium-oxygen bond length in various chromium oxides, with the sum of both crossover and valence X-ray normalized intensities being the most sensitive measure.

[Nose disease caused by occupational exposure to chromium in the electroplating industry: cytomorphological aspects].

Science.gov (United States)

Bolla, I; Gariboldi, L M; Gabrielli, M; Baldo, D; Romanelli, A; Tuberti, E; Magnani, F

1990-01-01

Twenty-six workers were studied (9 chrome-platers exposed to chromium dioxide and 17 workers exposed to metallic chromium dust) in order to investigate the macroscopic and cytological changes of the nasal mucosa due to exposure to water-soluble hexavalent chromium or to metallic chromium dust in the electroplating industry and the role of different valencies in the onset of nasal disease. Experimental and epidemiological data have shown that hexavalent chromium, which has strong oxidative power, induces more noticeable toxic effects on tissues and mucous membranes than other compounds. The correlation between the degree of local toxic effects and the chemical state of chromium was demonstrated in both the macro- and the microscopic investigations and in particular in the cytological examinations: cases of atypia were found only in workers exposed to hexavalent chromium. Evidence of atypia raises the question of whether hexavalent chromium may act as a carcinogenic agent on the rhinosinusal mucosa. For this reason, the introduction of cytological nasal examination in health surveillance programmes for this category of workers acquires considerable importance. Sample collection from the nasal mucosa by brushing is the method of choice since it is simple, non-invasive and gives good diagnostic results.

Corrosion behavior of porous chromium carbide in supercritical water

International Nuclear Information System (INIS)

Dong Ziqiang; Chen Weixing; Zheng Wenyue; Guzonas, Dave

2012-01-01

Highlights: ► Corrosion behavior of porous Cr 3 C 2 in various SCW conditions was investigated. ► Cr 3 C 2 is stable in SCW at temperature below 420–430 °C. ► Cracks and disintegration were observed at elevated testing temperatures. ► Degradation of Cr 3 C 2 is related to the intermediate product CrOOH. - Abstract: The corrosion behavior of highly porous chromium carbide (Cr 3 C 2 ) prepared by a reactive sintering process was characterized at temperatures ranging from 375 °C to 625 °C in a supercritical water environment with a pressure of 25–30 MPa. The test results show that porous chromium carbide is stable in SCW environments at temperatures under 425 °C, above which disintegration occurred. The porous carbide was also tested under hydrothermal conditions of pressures between 12 MPa and 50 MPa at constant temperatures of 400 °C and 415 °C, respectively. The pressure showed little effect on the stability of chromium carbide in the tests at those temperatures. The mechanism of disintegration of chromium carbide in SCW environments is discussed.

Effects of chromium picolinate supplementation in type 2 diabetic patients

Directory of Open Access Journals (Sweden)

Niladê Rosinski Rocha

2014-10-01

Full Text Available The effects of chromium picolinate in Type 2 diabetic patients are investigated.  Seventeen Type 2 diabetic patients were randomly divided into two groups. The experimental group received fiber-rich hypocaloric diet and chromium picolinate whereas the control group received fiber-rich hypocaloric diet and placebo. The chromium picolinate was offered twice a day at the dose of 100 μg. Anthropometric data such as blood pressure, fasting glycemia and glycated hemoglobin (HbA1c were measured and these parameters were evaluated again after 90 days. No difference was reported in rates of body weight, waist, hip, body mass index, blood pressure and fasting glycemia (Control vs. Experimental groups after treatment. However, a decrease (p = 0.0405 of HbA1c occurred in the experimental group when the pre- and post-treatment rates were compared. HbA1c data showed that chromium picolinate improved the glycemic control in Type 2 diabetes.

The commensurate spin excitation in chromium: A polarised neutron investigation

International Nuclear Information System (INIS)

Pynn, R.; Stirling, W.G.

1991-01-01

A polarised neutron experiment with neutron energy analysis has been performed with a single-Q sample of chromium in a large magnetic field. The 4-meV ''commensurate'' mode is found to involve spin fluctuations parallel to the ordered chromium moments. 8 refs., 3 figs

Work Environment Factors and Their Influence on Urinary Chromium Levels in Informal Electroplating Workers

Science.gov (United States)

Setyaningsih, Yuliani; Husodo, Adi Heru; Astuti, Indwiani

2018-02-01

One of the informal sector which absorbs labor was electroplating business. This sector uses chromium as coating material because it was strong, corrosion resistant and strong. Nonetheless hexavalent chromium is highly toxic if inhaled, swallowed and contact with skin. Poor hygiene, the lack of work environment factors and sanitation conditions can increase the levels of chromium in the body. This aimed of this study was to analyze the association between work environment factors and levels of urinary chromium in informal electroplating worker. A Purposive study was conducted in Tegal Central Java. The research subjects were 66 male workers. Chi Square analysis was used to establish an association between work environment factors and level of urinary chromium. There is a relationship between heat stress and wind direction to the chromium levels in urine (p 0.05). This explains that work environment factors can increase chromium levels in the urine of informal electroplating workers.

Work Environment Factors and Their Influence on Urinary Chromium Levels in Informal Electroplating Workers

Directory of Open Access Journals (Sweden)

Setyaningsih Yuliani

2018-01-01

Full Text Available One of the informal sector which absorbs labor was electroplating business. This sector uses chromium as coating material because it was strong, corrosion resistant and strong. Nonetheless hexavalent chromium is highly toxic if inhaled, swallowed and contact with skin. Poor hygiene, the lack of work environment factors and sanitation conditions can increase the levels of chromium in the body. This aimed of this study was to analyze the association between work environment factors and levels of urinary chromium in informal electroplating worker. A Purposive study was conducted in Tegal Central Java. The research subjects were 66 male workers. Chi Square analysis was used to establish an association between work environment factors and level of urinary chromium. There is a relationship between heat stress and wind direction to the chromium levels in urine (p 0.05. This explains that work environment factors can increase chromium levels in the urine of informal electroplating workers.

75 FR 67100 - Superalloy Degassed Chromium From Japan

Science.gov (United States)

2010-11-01

... Chromium From Japan AGENCY: United States International Trade Commission. ACTION: Institution of a five-year review concerning the antidumping duty order on superalloy degassed chromium from Japan. SUMMARY... order on superalloy degassed chromium from Japan would be likely to lead to continuation or recurrence...

REMOVAL OF HEXAVALENT CHROMIUM FROM DRINKING WATER

Directory of Open Access Journals (Sweden)

A. R. Asgari ، F. Vaezi ، S. Nasseri ، O. Dördelmann ، A. H. Mahvi ، E. Dehghani Fard

2008-10-01

Full Text Available Removal of chromium can be accomplished by various methods but none of them is cost-effective in meeting drinking water standards. For this study, granular ferric hydroxide was used as adsorbent for removal of hexavalent chromium. Besides, the effects of changing contact time, pH and concentrations of competitive anions were determined for different amounts of granular ferric hydroxide. It was found that granular ferric hydroxide has a high capacity for adsorption of hexavalent chromium from water at pH≤7 and in 90 min contact time. Maximum adsorption capacity was determined to be 0.788 mg Cr+6/g granular ferric hydroxide. Although relatively good adsorption of sulfate and chloride had been specified in this study, the interfering effects of these two anions had not been detected in concentrations of 200 and 400 mg/L. The absorbability of hexavalent chromium by granular ferric hydroxide could be expressed by Freundlich isotherm with R2>0.968. However, the disadvantage was that the iron concentration in water was increased by the granular ferric hydroxide. Nevertheless, granular ferric hydroxide is a promising adsorbent for chromium removal, even in the presence of other interfering compounds, because granular ferric hydroxide treatment can easily be accomplished and removal of excess iron is a simple practice for conventional water treatment plants. Thus, this method could be regarded as a safe and convenient solution to the problem of chromium-polluted water resources.

H.R. 3236: A bill to improve treatment for veterans exposed to radiation while in military service, introduced in the US House of Representatives, One Hundred Second Congress, First Session, August 2, 1991

International Nuclear Information System (INIS)

Anon.

1991-01-01

This bill was introduced into the US House of Representatives on August 2, 1991 to improve treatment for veterans exposed to radiation while in military service. A section addresses the expansion of the list of diseases presumed to be service-connected for certain radiation-exposed veterans and elimination of latency-period limitations. Another section examines other activities involving exposure to ionizing radiation

Polymorphisms of Selected DNA Repair Genes and Lung Cancer in Chromium Exposure.

Science.gov (United States)

Halasova, E; Matakova, T; Skerenova, M; Krutakova, M; Slovakova, P; Dzian, A; Javorkova, S; Pec, M; Kypusova, K; Hamzik, J

2016-01-01

Chromium is a well-known mutagen and carcinogen involved in lung cancer development. DNA repair genes play an important role in the elimination of genetic changes caused by chromium exposure. In the present study, we investigated the polymorphisms of the following DNA repair genes: XRCC3, participating in the homologous recombination repair, and hMLH1 and hMSH2, functioning in the mismatch repair. We focused on the risk the polymorphisms present in the development of lung cancer regarding the exposure to chromium. We analyzed 106 individuals; 45 patients exposed to chromium with diagnosed lung cancer and 61 healthy controls. Genotypes were determined by a PCR-RFLP method. We unravelled a potential for increased risk of lung cancer development in the hMLH1 (rs1800734) AA genotype in the recessive model. In conclusion, gene polymorphisms in the DNA repair genes underscores the risk of lung cancer development in chromium exposed individuals.

REMOVAL OF HEXAVALENT CHROMIUM FROM AQUEOUS ...

African Journals Online (AJOL)

a

be used again to adsorb heavy metal ions. ... Among these heavy metals are chromium, copper and ... poisoning can result from high exposure to hexavalent chromium [2]. Most of the ..... At low pH, the sorbent is positively charged because of.

Progress in the chemistry of chromium(V) doping agents used in polarized target materials

International Nuclear Information System (INIS)

Krumpolc, M.; Hill, D.; Struhrmann, H.B.

1990-01-01

We wish to report progress in two areas of the chromium (V)-based doping agents: Two commonly used chromium (V) complexes, I and II, have been synthesized in perdeuterated form (i.e., all hydrogens replaced by deuterium). They are sodium bis(2-ethyl-2-deuteroxy-butyrato)oxochromate(V)monodeuterate, IV, (acronym EDBA-Cr(V)), and sodium bis(2-deuteroxy-2-methylpropionato)oxochromate(V), III, (acronym DMPA-Cr(V)). A synthetic route leading to the preparation of stable, chromium(III)-free solutions of chromium(V) in diols (1,2-ethanediol/ethylene glycol/and 1,2-propanediol/propylene glycol/) has been outlined

Native Chromium Resistant Staphylococci Species from a Fly Ash ...

African Journals Online (AJOL)

Sixty-six chromium-resistant Staphylococci species belonging to S. epidermidis, S. aureus, S. saprophyticus and S. arlettae were previously isolated from a chromium-polluted Fly ash (FA) dumping site in South Africa. However the genetic mechanisms responsible for chromium resistance were not known. Polymerase chain ...

Portable x-ray fluorescence for the analysis of chromium in nail and nail clippings

International Nuclear Information System (INIS)

Fleming, David E.B.; Ware, Chris S.

2017-01-01

Assessment of chromium content in human nail or nail clippings could serve as an effective biomarker of chromium status. The feasibility of a new portable x-ray fluorescence (XRF) approach to chromium measurement was investigated through analysis of nail and nail clipping phantoms. Five measurements of 180 s (real time) duration were first performed on six whole nail phantoms having chromium concentrations of 0, 2, 5, 10, 15, and 20 µg/g. Using nail clippers, these phantoms were then converted to nail clippings, and assembled into different mass groups of 20, 40, 60, 80, and 100 mg for additional measurements. The amplitude of the chromium Kα characteristic x-ray energy peak was examined as a function of phantom concentration for all measurement conditions to create a series of calibration lines. The minimum detection limit (MDL) for chromium was also calculated for each case. The chromium MDL determined from the whole nail intact phantoms was 0.88±0.03 µg/g. For the clipping phantoms, the MDL ranged from 1.2 to 3.3 µg/g, depending on the mass group analyzed. For the 40 mg clipping group, the MDL was 1.2±0.1 µg/g, and higher mass collections did not improve upon this result. This MDL is comparable to chromium concentration levels seen in various studies involving human nail clippings. Further improvements to the portable XRF technique would be required to detect chromium levels expected from the lower end of a typical population. - Highlights: • Portable x-ray fluorescence (XRF) was explored as a technique to assess levels of chromium in human nails or nail clippings. • Results were found to depend on the mass of clipping sample provided. • Minimum detection limits for chromium were similar to concentration levels found in previous studies of human nail clippings.

Online short-term heat load forecasting for single family houses

DEFF Research Database (Denmark)

Bacher, Peder; Madsen, Henrik; Nielsen, Henrik Aalborg

2013-01-01

. Every hour the hourly heat load for each house the following two days is forecasted. The forecast models are adaptive linear time-series models and the climate inputs used are: ambient temperature, global radiation, and wind speed. A computationally efficient recursive least squares scheme is used......This paper presents a method for forecasting the load for heating in a single-family house. Both space and hot tap water heating are forecasted. The forecasting model is built using data from sixteen houses in Sønderborg, Denmark, combined with local climate measurements and weather forecasts...... variations in the heat load signal (predominant only for some houses), peaks presumably from showers, shifts in resident behavior, and uncertainty of the weather forecasts for longer horizons, especially for the solar radiation....

Precipitation hardenable iron-nickel-chromium alloy having good swelling resistance and low neutron absorbence

International Nuclear Information System (INIS)

Korenko, M.K.; Merrick, H.F.; Gibson, R.C.

1982-01-01

An iron-nickel-chromium age-hardenable alloy suitable for use in fast breeder reactor ducts and cladding utilizes the gamma-double prime strengthening phase and has a morphology of the gamma-double prime phase enveloping the gamma-prime phase and delta phase distributed at or near the grain boundaries. The alloy consists essentially of about 40-50 percent nickel, 7.5-14 percent chromium, 1.5-4 percent niobium, .25-.75 percent silicon, 1-3 percent titanium, .1-.5 percent aluminum, .02-1 percent carbon, .002-.015 percent boron, and the balance iron. Up to 2 percent manganese and up to .01 percent magnesium may be added to inhibit trace element effects; up to .1 percent zirconium may be added to increase radiation swelling resistance; and up to 3 percent molybdenum may be added to increase strength

DNA-protein crosslinks in peripheral lymphocytes of individuals exposed to hexavalent chromium compounds.

Science.gov (United States)

Zhitkovich, A; Lukanova, A; Popov, T; Taioli, E; Cohen, H; Costa, M; Toniolo, P

1996-01-01

Abstract DNA-protein crosslinks were measured in peripheral blood lymphocytes of chrome-platers and controls from Bulgaria in order to evaluate a genotoxic effect of human exposure to carcinogenic Cr(VI) compounds. Chrome-platers and most of the unexposed controls were from the industrial city of Jambol; some additional controls were recruited from the seaside town of Burgas. The chrome-platers had significantly elevated levels of chromium in pre- and post-shift urine, erythrocytes and lymphocytes compared with the control subjects. The largest differences between the two groups were found in erythrocyte chromium concentrations which are considered to be indicative of Cr(VI) exposure. Despite the significant differences in internal chromium doses, levels of DNA-protein crosslinks were not significantly different between the combined controls and exposed workers. Individual DNA-protein crosslinks, however, correlated strongly with chromium in erythrocytes at low and moderate doses but at high exposures, such as among the majority of chrome-platers, these DNA adducts were saturated at maximum levels. The saturation of DNA-protein crosslinks seems to occur at 7-8 μg I-(1) chromium in erythrocytes whereas a mean erythrocyte chromium among the chrome platers was as high as 22.8 μg l(-1). Occupationally unexposed subjects exhibited a significant variability with respect to the erythrocyte chromium concentration, however erythrocyte chromium levels correlated closely with DNA-protein crosslinks in lymphocytes. The controls from Jambol had higher chromium concentrations in erythrocytes and elevated levels of DNA-protein crosslinks compared with Burgas controls. Occupational exposure to formaldehyde among furniture factory workers did not change levels of DNA-protein crosslinks in peripheral lymphocytes. DNA-protein crosslink measurements showed a low intraindividual variability and their levels among both controls and exposed indivduals were not affected by smoking, age

Optimization of chromium biosorption in aqueous solution by marine ...

African Journals Online (AJOL)

Optimization of a chromium biosorption process was performed by varying three independent variables pH (0.5 to 3.5), initial chromium ion concentration (10 to 30 mg/L), and Yarrowia lipolytica dosage (2 to 4 g/L) using a Doehlert experimental design (DD) involving response surface methodology (RSM). For the maximum ...

Role of functional groups on Aspergillus niger biomass in the detoxification of hexavalent chromium.

Science.gov (United States)

Narvekar, Sneha; Vaidya, Varsha K

2009-10-01

Chromium (VI) contamination is not uncommon, especially near industries involved in leather tanning, chrome painting, metal cleaning and processing, wood preservation and alloy preparation. The mutagenic and carcinogenic properties of Chromium (VI) necessitate effective remedial processes. Difficulties associated with chemical and physical techniques to remediate a Chromium (VI) contaminated site to EPA recommended level (50 ppm), in addition to higher costs involved, assert the need for bioremedial measures. Biosorption can be one such solution to clean up heavy metal contamination. The objective of this study was to examine the main aspects of a possible strategy for the removal of Chromium (VI), employing Aspergillus niger biomass. The roles played by amines, carboxylic acids, phosphates, in Chromium (VI) biosorption were studied. Amino and the carboxy groups on the fungal cell wall play an important role in sorption. However, the role of carboxy group was far less than amino group. Surface adsorption of Chromium (VI) was also seen by scanning electron microscopy (SEM) thus indicating involvement of ion-exchange and surface adsorption mechanism in removal of Chromium (VI) ions.

Hexavalent chromium induces chromosome instability in human urothelial cells

Energy Technology Data Exchange (ETDEWEB)

Wise, Sandra S. [Wise Laboratory of Environmental and Genetic Toxicology, Maine Center for Toxicology and Environmental Health, Department of Applied Medical Science, University of Southern Maine, Science Building, 96 Falmouth Street, Portland, ME 04103 (United States); Holmes, Amie L. [Wise Laboratory of Environmental and Genetic Toxicology, Maine Center for Toxicology and Environmental Health, Department of Applied Medical Science, University of Southern Maine, Science Building, 96 Falmouth Street, Portland, ME 04103 (United States); Department of Radiation Oncology, Dana Farber Cancer Institute, 450 Brookline Ave., Boston, MA 02215 (United States); Liou, Louis [Department of Pathology, Boston University School of Medicine, 670 Albany St., Boston, MA 02118 (United States); Adam, Rosalyn M. [Department of Surgery, Harvard Medical School, Boston, MA 02115 (United States); Wise, John Pierce Sr., E-mail: john.wise@louisville.edu [Wise Laboratory of Environmental and Genetic Toxicology, Maine Center for Toxicology and Environmental Health, Department of Applied Medical Science, University of Southern Maine, Science Building, 96 Falmouth Street, Portland, ME 04103 (United States)

2016-04-01

Numerous metals are well-known human bladder carcinogens. Despite the significant occupational and public health concern of metals and bladder cancer, the carcinogenic mechanisms remain largely unknown. Chromium, in particular, is a metal of concern as incidences of bladder cancer have been found elevated in chromate workers, and there is an increasing concern for patients with metal hip implants. However, the impact of hexavalent chromium (Cr(VI)) on bladder cells has not been studied. We compared chromate toxicity in two bladder cell lines; primary human urothelial cells and hTERT-immortalized human urothelial cells. Cr(VI) induced a concentration- and time-dependent increase in chromosome damage in both cell lines, with the hTERT-immortalized cells exhibiting more chromosome damage than the primary cells. Chronic exposure to Cr(VI) also induced a concentration-dependent increase in aneuploid metaphases in both cell lines which was not observed after a 24 h exposure. Aneuploidy induction was higher in the hTERT-immortalized cells. When we correct for uptake, Cr(VI) induces a similar amount of chromosome damage and aneuploidy suggesting that the differences in Cr(VI) sensitivity between the two cells lines were due to differences in uptake. The increase in chromosome instability after chronic chromate treatment suggests this may be a mechanism for chromate-induced bladder cancer, specifically, and may be a mechanism for metal-induced bladder cancer, in general. - Highlights: • Hexavalent chromium is genotoxic to human urothelial cells. • Hexavalent chromium induces aneuploidy in human urothelial cells. • hTERT-immortalized human urothelial cells model the effects seen in primary urothelial cells. • Hexavalent chromium has a strong likelihood of being carcinogenic for bladder tissue.

Genesis and transport of hexavalent chromium in the system ophiolitic rocks - groundwater

Science.gov (United States)

Shchegolikhina, Anastasia; Guadagnini, Laura; Guadagnini, Alberto

2015-04-01

Our study aims at contributing to the quantification and characterization of chromium transport processes from host rocks and soil matrices to groundwater. We focus on dissolved hexavalent chromium detected in groundwaters of geological regions with ophiolitic rocks (ophiolites and serpentinites) inclusions due to its critical ecological impact. (Oze et al., 2004). Despite the large number of analyses on the occurrence of high concentrations of hazardous hexavalent chromium ions in natural waters, only few studies were performed with the objective of identifying and investigating the geochemical reactions which could occur in the natural system rock - groundwater - dissolved chromium (Fantoni et al., 2002, Stephen and James, 2004, Lelli et al., 2013). In this context, there is a need for integration of results obtained from diverse studies in various regions and settings to improve our knowledge repository. Our theoretical analyses are grounded and driven by practical scenarios detected in subsurface reservoirs exploited for civil and industrial use located in the Emilia-Romagna region (Italy). Available experimental datasets are complemented with data from other international regional-scale settings (Altay mountains region, Russia). Modeling of chromium transformation and migration particularly includes characterization of the multispecies geochemical system. A key aspect of our study is the analysis of the complex competitive sorption processes governing heavy metal evolution in groundwater. The results of the research allow assessing the critical qualitative features of the mechanisms of hexavalent chromium ion mobilization from host rocks and soils and the ensuing transformation and migration to groundwater under the influence of diverse environmental factors. The study is then complemented by the quantification of the main sources of uncertainty associated with prediction of heavy metal contamination levels in the groundwater system explored. Fantoni, D

21 CFR 73.1015 - Chromium-cobalt-aluminum oxide.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium-cobalt-aluminum oxide. 73.1015 Section 73... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1015 Chromium-cobalt-aluminum oxide. (a) Identity. The color additive chromium-cobalt-aluminum oxide is a blue-green pigment obtained by calcining a...

[In vitro percutaneous absorption of chromium powder and the effect of skin cleanser].

Science.gov (United States)

D'Agostin, F; Crosera, M; Adami, G; Malvestio, A; Rosani, R; Bovenzi, M; Maina, G; Filon, F Larese

2007-01-01

Occupational chromium dermatitis occurs frequently among cement and metal workers, workers dealing with leather tanning and employees in the ceramic industry. The present study, using an in-vitro system, evaluated percutaneous absorption of chromium powder and the effect of rapid skin decontamination with a common detergent. Experiments were performed using the Franz diffusion cell method with human skin. Physiological solution was used as receiving phase and a suspension of chromium powder in synthetic sweat was used as donor phase. The tests were performed without or with decontamination using the cleanser 30 minutes after the start of exposure. The amount of chromium permeated through the skin was analysed by Inductively Coupled Plasma Atomic Emission Spectroscopy and Electro Thermal Atomic Absorption Spectroscopy. Speciation analysis and measurements of chromium skin content were also performed. We calculated a permeation flux of 0.843 +/- 0.25 ng cm(-2) h(-1) and a lag time of 1.1 +/- 0.7 h. The cleaning procedure significantly increased chromium skin content, whereas skin passage was not increased. These results showed that chromium powder can pass through the skin and that skin decontamination did not decrease skin absorption. Therefore, it is necessary to prevent skin contamination when using toxic agents.

Determination of the vacancy formation enthalpy in chromium by positron annihilation

International Nuclear Information System (INIS)

Loper, G.D.; Smedskjaer, L.C.; Chason, M.K.; Siegel, R.W.

1985-01-01

Doppler broadening of the positron annihilation lineshape in 99.99 at. % pure chromium was measured over the temperature range 296 to 2049 0 K. The chromium sample was encapsulated in sapphire owing to its high vapor pressure near melting. Saturation-like behavior of the lineshape was observed near the melting temperature (2130 0 K). A two-state trapping model fit to the data yielded a vacancy formation enthalpy of 2.0 +- 0.2 eV. This result is discussed in relation to extant empirical relations for vacancy migration and self-diffusion in metals and to data from previous self-diffusion and annealing experiments in chromium. It is concluded that the observed vacancy ensemble is unlikely to be responsible for the measured self-diffusion behavior. The implications of the present results in terms of our understanding of mechanisms for self-diffusion in chromium and other refractory bcc metals are discussed

Sorption of chromium(VI) and chromium(III) on aluminium hydroxide

International Nuclear Information System (INIS)

Music, S.

1986-01-01

Factors that influence the sorption of Cr(VI) and Cr(III) on aluminium hydroxide were investigated. The sorption of chromates decreases as the pH of the suspension increases. The mechanism of CrOsub(4)sup(2-) sorption was interpreted in terms of reactions between chromates and -OH and/or Hsub(2)O groups at the hydroxide/liquid interface. It was shown that chromates are more tightly sorbed on aluminium hydroxide compared to other anions, e.g. chlorides. On the other hand, specifically absorbed anions, such as molybdates, compete strongly with chromates for the sorption sites. The sorption of chromium(III) increases with the pH of the suspension. Also, the sorption of chromium(III) is suppressed in the presence of citrate ions. The best conditions for the fixation of Cr(VI) and Cr(III) by aluminium hydroxide are presented. (author)

Predicting chromium (VI) adsorption rate in the treatment of liquid ...

African Journals Online (AJOL)

The adsorption rate of chromium (VI) on commercial activated carbon during the treatment of the flocculation effluent of liquid-phase oil-based drill-cuttings has been investigated in terms of contact time and initial chromium (VI) ion concentration. Homogenizing 1 g of the activated carbon with 100 ml of the flocculation ...

FERRATE TREATMENT FOR REMOVING CHROMIUM FROM HIGH-LEVEL RADIOACTIVE TANK WASTE

International Nuclear Information System (INIS)

Sylvester, Paul; Rutherford, Andy; Gonzalez-Martin, Anuncia; Kim, J.; Rapko, Brian M.; Lumetta, Gregg J.

2000-01-01

A method has been developed for removing chromium from alkaline high-level radioactive tank waste. Removing chromium from these wastes is critical in reducing the volume of waste requiring expensive immobilization and deep geologic disposition. The method developed is based on the oxidation of insoluble chromium(III) compounds to soluble chromate using ferrate. The tests conducted with a simulated Hanford tank sludge indicate that the chromium removal with ferrate is more efficient at 5 M NaOH than at 3 M NaOH. Chromium removal increases with increasing Fe(VI)/Cr(III) molar ratio, but the chromium removal tends to level out for Fe(VI)/Cr(III) greater than 10. Increasing temperature leads to better chromium removal, but higher temperatures also led to more rapid ferrate decomposition. Tests with radioactive Hanford tank waste generally confirmed the simulant results. In all cases examined, ferrate enhanced the chromium removal, with a typical removal of around 60-70% of the total chromium present in the washed sludge solids. The ferrate leachate solutions did not contain significant concentrations of transuranic elements, so these solutions could be handled as low-activity waste

Bioaccumulation of chromium and nickel in the tissues of Barb us ...

African Journals Online (AJOL)

1996-04-25

Apr 25, 1996 ... S, marequensis suggested no serious chromium or nickel pollution in the study area. "To \\~hom . ... The toxicity of chromium and nickel to fish, as individual elements, is ..... its fitness for human consumption). One should also ...

Effect of individual and group housing of mice on the level of radioresistance

Directory of Open Access Journals (Sweden)

Dorozhkina O.V.

2015-12-01

Full Text Available Aim: to examine the effect of individual and group housing of mice on radioresistance. Material and methods. Effects of individual and group housing of mice on immunity and blood systems were studied on ICR (CD-1 and C57BI6 male mice before and after proton irradiation. Results. Group housing of intact animals resulted in a decline in the number of nucleated cells in the femur bone marrow and thymus mass. The irradiation with proton with energy of 171 MeV at a dose of 1 Gy causes a statistically significant greater reduction of the number of nucleated cells in the femur bone marrow in group-housed mice. A trend toward greater safety of the number of leukocytes in the peripheral blood and higher proliferative activity of bone marrow cells, as well as lower level of aberrant mitoses have been noted in individually-housed mice. Reduction processes in the recovery period of radiation sickness take place at a greater rate in group-housed mice. Conclusion. Group housing of male mice causes increased sensitivity of the blood and immunity systems to the effects of radiation and at the same time accelerates processes of radiation recovery.

The fate of chromium during tropical weathering

DEFF Research Database (Denmark)

Berger, Alfons; Frei, Robert

2014-01-01

We performed a mineral, geochemical and Cr–Sr–Pb isotope study on a laterite profile developed on ca. 540 Ma old tonalitic bedrock in Madagascar with special emphasis on the behavior of chromium during tropical weathering. The observed strong depletions of Ca, Si, and P, and enrichment of Fe and Al...... of a former, positively fractionated and mobile chromium pool has been experimentally constrained in circumneutral and basic leachates of powdered tonalite bedrock where δ53Cr of + 0.21 to + 0.48‰ was measured. Our results show that mobilization of chromium is effective under highly oxidative conditions...

Impurities in chromium deposits produced by electroplating and physical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

Dini, J.W.

1994-05-01

Impurity contents in electrodeposited (hexavalent and trivalent) chromium deposits and physically vapor deposited (thermal evaporation, electron beam evaporation and rf-sputtering) were compared. Oxygen is the key impurity obtained in electrodeposited films but it can be minimized in hexavalent plating solutions by operating at high temperature, e. g., 85 C. Electrodeposits produced in trivalent chromium plating solutions and physically vapor deposited films have much higher oxygen contents than electrodeposits produced in hexavalent chromium solutions operated at temperatures around 85 C. Depending on the target material used for physically vapor deposited films, these films can also have high amounts of other impurities.

Chromium-induced membrane damage: protective role of ascorbic acid.

Science.gov (United States)

Dey, S K; Nayak, P; Roy, S

2001-07-01

Importance of chromium as environmental toxicant is largely due to impact on the body to produce cellular toxicity. The impact of chromium and their supplementation with ascorbic acid was studied on plasma membrane of liver and kidney in male Wistar rats (80-100 g body weight). It has been observed that the intoxication with chromium (i.p.) at the dose of 0.8 mg/100 g body weight per day for a period of 28 days causes significant increase in the level of cholesterol and decrease in the level of phospholipid of both liver and kidney. The alkaline phosphatase, total ATPase and Na(+)-K(+)-ATPase activities were significantly decreased in both liver and kidney after chromium treatment, except total ATPase activity of kidney. It is suggested that chromium exposure at the present dose and duration induce for the alterations of structure and function of both liver and kidney plasma membrane. Ascorbic acid (i.p. at the dose of 0.5 mg/100 g body weight per day for period of 28 days) supplementation can reduce these structural changes in the plasma membrane of liver and kidney. But the functional changes can not be completely replenished by the ascorbic acid supplementation in response to chromium exposure. So it is also suggested that ascorbic acid (nutritional antioxidant) is useful free radical scavenger to restrain the chromium-induced membrane damage.

[Occupational exposure to hexavalent chromium during aircraft painting].

Science.gov (United States)

Gherardi, M; Gatto, M P; Gordiani, A; Paci, E; Proietto, A

2007-01-01

Hygienists are interested in hexavalent chromium due to its genotoxic and carcinogenic effect on humans. The use of products containing hexavalent chromium is decreasing in many industrial fields because of the substitution with less-toxic compounds. In the aeronautical industry, however, the chromate are added to primer paint as a corrosion inhibitor of aircrafts surfaces: so hexavalent chromium compounds are available in many primers with a composition ranging from 10% to 13%. The application of these primers by using electrostatic guns potentially exposes painting and coating workers at high concentrations of aerosols containing Cr(VI). The aim of the present study is the evaluation of professional exposure to hexavalent chromium during aircraft painting, by adopting both environmental personal sampling and biological monitoring. To valuate workers exposure levels the personal measurements results have been compared with the exposure limit values (TLV-TWA) and the urinary chromium contents with the biological exposure indices (IBE). Moreover the strategy of coupling environmental sampling with biological monitoring seems to be a useful instrument to measure the validity of the individual protection devices.

Effect of yttria addition on the stability of porous chromium oxide ceramics in supercritical water

International Nuclear Information System (INIS)

Dong Ziqiang; Chen Weixing; Zheng Wenyue; Guzonas, Dave

2013-01-01

Porous chromium oxide (Cr 2 O 3 ) ceramics were prepared by oxidizing highly porous chromium carbides that were obtained by a reactive sintering method, and were evaluated at temperatures ranging from 375 °C to 625 °C in supercritical water (SCW) environments with a fixed pressure of 25–30 MPa. Reactive element yttrium was introduced to the porous oxide ceramic by adding various amounts of yttria of 5, 10 and 20 wt.%, respectively, prior to reactive sintering. The exposure in SCW shows that the porous chromium oxide is quite stable in SCW at 375 °C. However, the stability decreased with increasing temperature. It is well known that chromium oxide can be oxidized to soluble chromium (VI) species in SCW when oxygen is present. Adding yttria increases the stability of chromium oxide in SCW environments. However, adding yttria higher than 5 wt.% increased the weight loss of porous chromium oxide samples because of the direct dissociation of Y 2 O 3 in SCW.

Cytokine detection for the diagnosis of chromium allergy*

Science.gov (United States)

Martins, Luis Eduardo Agner Machado; dos Reis, Vitor Manoel Silva

2013-01-01

BACKGROUND Patch testing remains the gold standard method for the identification of the etiologic agent of allergic contact dermatitis. However, it is a subjective, time-consuming exam whose technique demands special care and which presents some contraindications, which hamper its use. In a recent study, we showed that the proliferation assay can suitably replace patch testing for the diagnosis of chromium allergy, which had been previously demonstrated only for nickel allergy. In this study, we try to refine the method by reducing the incubation period of cultures for lymphocyte proliferation assays in response to chromium. OBJECTIVE Develop an alternative or complementary diagnostic test for chromium allergic contact dermatitis. METHODS We compared the production of 9 cytokines (IFN-γ, IL-2, IL-4, IL-5, IL-10, IL-12, IL-13, IL-17 and RANTES) between 18 chromium-allergic patients and 19 controls. RESULTS Chromium increased the production of IFN-y, IL-5, IL-2 and IL-13 in allergic patients, but only IL-2 and especially IL-13 helped discriminate allergic patients from controls. The sensitivity, specificity and accuracy found with IL-13 were about 80%. CONCLUSIONS IL-13 and IL-2 detection may be used to diagnose chromium allergy in 2-day cultures. However, in general, the 6-day cultures seem to be superior for this purpose. PMID:24173176

Reducing elution in anion exchange chromatography as a pretreatment of colorimetry of chromium(VI) and vanadium(V)

International Nuclear Information System (INIS)

Shigetomi, Yasumasa; Hatamoto, Takeji; Nagoshi, Kimie; Yamashige, Takashi.

1976-01-01

In order to increase the selectivity of the colorimetry of chromium and vanadium, the separation by means of anion exchange chromatography was tested. The column, phi 0.8x5.0 cm packing (50--100 mesh) Dowex 1x4 anion exchange resin was used for the separation of chromium. The solution containing chromium (VI), zinc(II), cadmium(II), iron(III) and reducing organic substances contained in industrial waste water was introduced into the column and then the substances other than chromium(VI) were removed by washing the column with distilled water. Finally chromium(VI) was reduced to chromium(III) by hydroxylamine in the eluent and eluted. The concentration of sulfuric acid and hydroxylamine in the eluent were 0.1 mol/l and 0.001 mol/l respectively. For analyzing chromium(III) in the mixture of chromium(VI) and chromium(III), after removal of chromium(VI) it should be oxidized to chromium(VI) anion with the oxidant, e.g., sodium peroxide or hydrogen peroxide, before introducing it into the column. In terms of the pretreatment by using the acetate form resin column, chromium (VI) and chromium(III) can be determined separately in the solution whose concentration ranges from 0.05 ppm to 0.5 ppm despite the presence of contaminants, which interfere with the colorimetric determination of chromium(VI) using diphenylcarbonohydrazide, in the original solution. The separation of vanadium(V) in the solution containing copper(II), cobalt(II) and etc. was made using the mixed solution of hydrochloric acid (2 mol/l) and hydroxylamine (0.2 mol/l) similarly to chromium(VI). In terms of the similar pretreatment vanadium could be determined precisely as far as 0.1 ppm by the colorimetry using 4-(2-pyridylazo) resorcinol despite the presence of copper(II), cobalt(II), nickel(II) and etc in the original solution. (auth.)

Comparison of Ultrasound-Assisted and Regular Leaching of Vanadium and Chromium from Roasted High Chromium Vanadium Slag

Science.gov (United States)

Wen, Jing; Jiang, Tao; Gao, Huiyang; Liu, Yajing; Zheng, Xiaole; Xue, Xiangxin

2018-02-01

Ultrasound-assisted leaching (UAL) was used for vanadium and chromium leaching from roasted material obtained by the calcification roasting of high-chromium-vanadium slag. UAL was compared with regular leaching. The effect of the leaching time and temperature, acid concentration, and liquid-solid ratio on the vanadium and chromium leaching behaviors was investigated. The UAL mechanism was determined from particle-size-distribution and microstructure analyses. UAL decreased the reaction time and leaching temperature significantly. Furthermore, 96.67% vanadium and less than 1% chromium were leached at 60°C for 60 min with 20% H2SO4 at a liquid-solid ratio of 8, which was higher than the maximum vanadium leaching rate of 90.89% obtained using regular leaching at 80°C for 120 min. Ultrasonic waves broke and dispersed the solid sample because of ultrasonic cavitation, which increased the contact area of the roasted sample and the leaching medium, the solid-liquid mass transfer, and the vanadium leaching rate.

The relationship between microstructure and mechanical properties of ferritic chromium steel weldments

Energy Technology Data Exchange (ETDEWEB)

Mayr, Peter; Cerjak, Horst [Graz Univ. of Technology (Austria); Toda, Yoshiaki; Hara, Toru; Abe, Fujio [National Institute for Materials Science (Japan)

2008-07-01

Welding as the major joining and repair technology for steels in thermal power plants has a significant influence on the steels microstructure and, therefore, on its properties. Heat-resistant martensitic 9-12% chromium steels show an affinity to the retention of delta ferrite in the heat-affected zone of their weldments. This is related to their high level of ferrite stabilizing alloying elements such as Cr, W or Mo. Retained delta ferrite in martensitic steel grades has a significant negative influence on creep strength, fatigue strength, toughness and oxidation resistance. In the long-term range of creep exposure, many weldments of martensitic heatresistant steels fail by Type IV cracking in the fine-grained region of the heat-affected zone. In this work, the formation of the heat-affected zone microstructures in martensitic chromium steels is studied by in-situ X-ray diffraction using synchrotron radiation, optical microscopy as well as most advanced electron microscopical methods. The observed microstructure is directly linked to the mechanical properties, i.e. ductility, toughness and creep strength. Characteristic failure modes are discussed in detail. (orig.)

Comparison of chromium-51 and iron-59 for estimating erythrocyte survival in the cat

International Nuclear Information System (INIS)

Liddle, C.G.; Putnam, J.P.; Berman, E.; Fisher, H.; Ostby, J.

1984-01-01

Erythrocyte survival studies were conducted on eight normal, healthy, 1-year-old male specific-pathogen-free cats using both chromium-51 and iron-59 simultaneously. The chromium-51 procedure gave a half-life value of 11.1 +/- 0.9 days. This was considerably lower than would be expected on the basis of the experimentally determined iron-59 erythrocyte survival time of 51.2 +/- 14.9 days. The results of this study indicated that there was considerable loss of the chromium-51 label in the cat other than that from senescence alone. An analysis of the chromium-51 disappearance curve indicated that there were two exponential disappearance rates for the chromium-51 label and, in the absence of cell death, approximately 67% of the label was lost with a rate constant of 0.02 per day and 33% was lost with a rate constant of 0.1 per day. An equation is presented which models the loss of chromium-51 label which could be used to calculate erythrocyte survival from a chromium-51 disappearance curve. Blood volume measurements, hemograms, bone marrow differential results, and iron kinetic values also were determined and the results presented. While a reasonable approximation of the erythrocyte life span could be made by correcting the chromium-51 values for losses other than senescence, the iron-59 procedure would be the preferred method in cats

New Evidence against Chromium as an Essential Trace Element.

Science.gov (United States)

Vincent, John B

2017-12-01

Nearly 60 y ago, chromium, as the trivalent ion, was proposed to be an essential element, but the results of new studies indicate that chromium currently can only be considered pharmacologically active and not an essential element. Regardless, articles still continue to appear in the literature claiming chromium is an essential element. Chromium has been marketed as an agent to reduce body mass and develop muscle; however, such marketing claims are no longer allowed in the United States because these claims, similar to claims of essential status, are not supported by experiments. Trivalent chromium has also been proposed as a therapeutic agent to increase insulin sensitivity and affect lipid metabolism. Although effective in certain rodent models, beneficial effects in humans have not been unequivocally established. Molecular mechanisms have been proposed for the beneficial effects but have not been definitively shown to occur in animals. © 2017 American Society for Nutrition.

The hazard of chromium exposure to neonates in Guiyu of China

International Nuclear Information System (INIS)

Li Yan; Xu Xijin; Liu Junxiao; Wu Kusheng; Gu Chengwu; Shao Guo; Chen Songjian; Chen Gangjian; Huo Xia

2008-01-01

Guiyu is one of the most heavily chromium-polluted areas in China due to the presence of numerous electronic waste (e-waste) recycling sites in the region. In this study, we investigate the effect of umbilical cord blood chromium levels (UCBCLs) on neonates from Guiyu and discuss chromium-induced DNA damage of cord blood lymphocyte. Umbilical cord blood samples were collected from neonates of Guiyu (in 2006, n = 100; in 2007, n = 100) and the neighboring town of Chaonan (in 2006, n = 52; in 2007, n = 50) that is associated with the fishery. UCBCLs of the neonates were determined by graphite atomizer absorption spectrophotometer. Comet experiment was used to examine lymphocyte DNA damage. Questionnaires to gauge chromium exposure were administered to the mothers of the neonates. The mean UCBCLs of neonates in the Guiyu group in 2006 and 2007 were 303.38 μg/L and 99.90 μg/L with median 93.89 μg/L and 70.60 μg/L, respectively. We observed significant differences between the results in UCBCLs of neonates in Guiyu and the control group (P 0.05). Higher levels of chromium in neonates were found to correlate with their mothers' exposure to e-waste recycling. There were significant differences in terms of DNA damage between the Guiyu group and the control group (P < 0.05). There was a correlation between DNA damage and the UCBCLs of neonates (P < 0.05). There is conclusive evidence that high UCBCLs in neonates exists in e-waste recycling areas in Guiyu and that e-waste recycling activity poses serious environmental problems. Chromium pollution is threatening the health of neonates around the recycling sites

Electron magnetic resonance investigation of chromium diffusion in yttria powders

Energy Technology Data Exchange (ETDEWEB)

Biasi, R.S. de, E-mail: rsbiasi@ime.eb.b [Secao de Engenharia Mecanica e de Materiais, Instituto Militar de Engenharia, Pr. General Tiburcio, 80, 22290-270 Rio de Janeiro, RJ (Brazil); Grillo, M.L.N., E-mail: mluciag@uerj.b [Instituto de Fisica, Universidade do Estado do Rio de Janeiro, 20550-013 Rio de Janeiro, RJ (Brazil)

2010-03-01

The electron magnetic resonance (EMR) technique was used to investigate the diffusion of chromium in yttria (Y{sub 2}O{sub 3}) powders. The EMR absorption intensity was measured for several annealing times and three different temperatures of isothermal annealing: 1273, 1323 and 1373 K. The activation temperature for diffusion, calculated from the experimental data using a theoretical model based on the Fick equation, was found to be E{sub A}=342+-5 kJ mol{sup -1}. This value is larger than the activation energy for the diffusion of chromium in rutile (TiO{sub 2}), periclase (MgO) and cobalt monoxide (CoO) and smaller than the activation energy for the diffusion of chromium in chrysoberyl (BeAl{sub 2}O{sub 4}).

Smart Houses

Science.gov (United States)

1987-01-01

GWS takes plans for a new home and subjects them to intensive computerized analysis that does 10,000 calculations relative to expected heat loss and heat gain, then provides specifications designed specifically for each structure as to heating, cooling, ventilation and insulation. As construction progresses, GWS inspects the work of the electrical, plumbing and insulation contractors and installs its own Smart House Radiant Barrier. On completion of the home, GWS technicians use a machine that creates a vacuum in the house and enables computer calculation of the air exchanged, a measure of energy efficiency. Key factor is the radiant barrier, borrowed from the Apollo program. This is an adaptation of a highly effective aluminized heat shield as a radiation barrier holding in or keeping out heat, cold air and water vapor.

Hexavalent Chromium reduction by Trichoderma inhamatum

Energy Technology Data Exchange (ETDEWEB)

Morales-Battera, L.; Cristiani-Urbina, E.

2009-07-01

Reduction of hexavalent chromium [Cr(VI)] to trivalent chromium [Cr(III)] is a useful and attractive process for remediation of ecosystems and industrial effluents contaminated with Cr(VI). Cr(VI) reduction to Cr(II) can be achieved by both chemical and biological methods; however, the biological reduction is more convenient than the chemical one since costs are lower, and sludge is generated in smaller amounts. (Author)

Workshop on effects of chromium coating on Nb3Sn superconductor strand: Proceedings

International Nuclear Information System (INIS)

1994-01-01

This report discusses the following topics: Chromium coating on superconductor strand -- an overview; technology of chromium plating; comparison of wires plated by different platers; search for chromium in copper; strand manufactures' presentations; chromium plating at the Lawrence Livermore National Laboratory; a first look at a chromium plating process development project tailored for T.P.X. and I.T.E.R. strand; and influence of chromium diffusion and related phenomena on the reference ratios of bare and chromium plated Nb 3 Sn strand

House characteristics associated with gamma radiation and radon daughter working levels in eastern Pennsylvania

International Nuclear Information System (INIS)

Stebbings, J.H.; Dignam, J.J.; Anast, G.A.; Reilly, M.A.; Gerusky, T.M.; Hartman, T.T.

1988-01-01

Working levels (WL) of radon daughters and γ measurements in basements are described for ∼ 1200 houses near the Reading Prong. House variables included condition and construction materials of basement floors and walls, basement heights and areas, heating systems, air conditioning, water supply, and presence of drains and sump pumps. WLs were poorly predicted by house characteristics or γ measurements, while γ levels were well predicted by house characteristics and WL. Factors predicting high γ levels tended to be associated with low WLs and vice versa. Dirt basement floors and fieldstone basement walls were strongly associated with high γ levels, as were poor wall conditions in multivariate analyses. Gamma levels were low in electrically heated homes. High WLs were strongly associated with electric heat, low WLs with basement walls of fieldstone and/or in poor condition. Large house volumes and well water supply were also associated with higher WLs. (author)

Study of the Thermodynamics of Chromium(III) and Chromium(VI) Binding to Fe3O4 and MnFe2O4 nanoparticles

Science.gov (United States)

Luther, Steven; Brogfeld, Nathan; Kim, Jisoo; Parsons, J.G.

2013-01-01

Removal of chromium(III) or (VI) from aqueous solution was achieved using Fe3O4, and MnFe2O4 nanomaterials. The nanomaterials were synthesized using a precipitation method and characterized using XRD. The size of the nanomaterials was determined to be 22.4 ± 0.9 nm (Fe3O4) and 15.5 ± 0.5 nm (MnFe2O4). The optimal binding pH for chromium(III) and chromium(VI) were pH 6 and pH 3. Isotherm studies were performed, under light and dark conditions, to determine the capacity of the nanomaterials. The capacities for the light studies with MnFe2O4 and Fe3O4 were determined to be 7.189 and 10.63 mg/g, respectively, for chromium(III). The capacities for the light studies with MnFe2O4 and Fe3O4 were 3.21 and 3.46 mg/g, respectively, for chromium(VI). Under dark reaction conditions the binding of chromium(III) to the MnFe2O4 and Fe3O4 nanomaterials were 5.74 and 15.9 mg/g, respectively. The binding capacity for the binding of chromium(VI) to MnFe2O4 and Fe3O4 under dark reaction conditions were 3.87 and 8.54 mg/g, respectively. The thermodynamics for the reactions showed negative ΔG values, and positive ΔH values. The ΔS values were positive for the binding of chromium(III) and for chromium(VI) binding under dark reaction conditions. The ΔS values for chromium(VI) binding under the light reaction conditions were determined to be negative. PMID:23558081

Reproductive toxicity of chromium in adult bonnet monkeys (Macaca radiata Geoffrey). Reversible oxidative stress in the semen

International Nuclear Information System (INIS)

Subramanian, Senthivinayagam; Rajendiran, Gopalakrishnan; Sekhar, Pasupathi; Gowri, Chandrahasan; Govindarajulu, Pera; Aruldhas, Mariajoseph Michael

2006-01-01

The present study was designed to test the hypothesis that oxidative stress mediates chromium-induced reproductive toxicity. Monthly semen samples were collected from adult monkeys (Macaca radiata), which were exposed to varying doses (50, 100, 200 and 400 ppm) of chromium (as potassium dichromate) for 6 months through drinking water. Chromium treatment decreased sperm count, sperm forward motility and the specific activities of antioxidant enzymes, superoxide dismutase and catalase, and the concentration of reduced glutathione in both seminal plasma and sperm in a dose- and duration-dependent manner. On the other hand, the quantum of hydrogen peroxide in the seminal plasma/sperm from monkeys exposed to chromium increased with increasing dose and duration of chromium exposure. All these changes were reversed after 6 months of chromium-free exposure period. Simultaneous supplementation of vitamin C (0.5 g/L; 1.0 g/L; 2.0 g/L) prevented the development of chromium-induced oxidative stress. Data support the hypothesis and show that chronic chromium exposure induces a reversible oxidative stress in the seminal plasma and sperm by creating an imbalance between reactive oxygen species and antioxidant system, leading to sperm death and reduced motility of live sperm

Alloy formation during chromium electrodeposition at niobium cathode in molten salts

International Nuclear Information System (INIS)

Kuznetsov, S.A.; Glagolevskaya, A.L.

1993-01-01

Alloy formation during electrodeposition of chromium at niobium cathode is studied in salt melts. It is shown that during chromium electrodeposition at niobium support intermetallic compound Cr 2 Nb is formed. Thermodynamic characteristics of Cr 0.66 Nb 0.33 alloy are determined. 10 refs., 1 fig

40 CFR 424.70 - Applicability; description of the electrolytic chromium subcategory.

Science.gov (United States)

2010-07-01

... electrolytic chromium subcategory. 424.70 Section 424.70 Protection of Environment ENVIRONMENTAL PROTECTION... Electrolytic Chromium Subcategory § 424.70 Applicability; description of the electrolytic chromium subcategory. The provisions of this subpart are applicable to discharges resulting from the manufacture of chromium...

Chromium Salen Mediated Alkene Epoxidation

DEFF Research Database (Denmark)

Petersen, Kaare Brandt; Norrby, Per-Ola; Daly, Adrian M.

2002-01-01

The mechanism of alkene epoxidation by chromium(v) oxo salen complexes has been studied by DFT and experimental methods. The reaction is compared to the closely related Mn-catalyzed process in an attempt to understand the dramatic difference in selectivity between the two systems. Overall......-spin surface. The low-spin addition of metal oxo species to an alkene leads to an intermediate which forms epoxide either with a barrier on the low-spin surface or without a barrier after spin inversion. Supporting evidence for this intermediate was obtained by using vinylcyclopropane traps. The chromium...

Predicting chromium (VI) adsorption rate in the treatment of liquid ...

African Journals Online (AJOL)

Administrator

The adsorption rate of chromium (VI) on commercial activated carbon during the ... time and initial chromium (VI) ion concentration. .... model, the separation factor r, according to Calvo et al (2001) cited .... Lead (II) and nickel (II) adsorption kinetics .... heavy metal by Talaromyces helicus: a trained fungus for copper and.

Contingency plans for chromium utilization. Publication NMAB-335

International Nuclear Information System (INIS)

1978-01-01

The United States depends entirely on foreign sources for the critical material, chromium, making it very vulnerable to supply disruptions. This vulnerability results because chromium is essential for the fabrication of corrosion-resisting steels and high-temperature, oxidation-resisting alloys in applications that are vital to the nation's technological well-being; because no substitutes are known for these materials in those applications; and because the known, substantial deposits of chromite ore are only in a few geographical locations that could become inaccessible to the United States as a result of political actions. The effectiveness of programs such as stockpiling, conservation, and research and development for substitutes to reduce the impact of disruption of imports of chromite and ferrochromium are discussed. Alternatives for decreasing chromium consumption also are identified for chromium-containing materials in the areas of design, processing, and substitution

Ventilation techniques and radon in small houses

International Nuclear Information System (INIS)

Keskinen, J.; Graeffe, G.; Janka, K.

1988-01-01

Indoor radon is the main cause of radiation exposure in Finland. The National Board of Health set the recommended concentration limits in 1986: an action level of 800 Bq/m 3 and a planning value of 200 Bq/m 3 for new buildings. The 800 Bq/m 3 concentration is estimated to be exceeded in 1.4% of the housing. This rather high number has motivated a number of studies concerning countermeasures against radon in existing houses. The purpose of this study was to find out possible remedial actions against radon using standard ventilation techniques. The ventilation rates were not increased over 0.71/h in order to have a realistic view about the possibilities of the state-of-the-art techniques. Special attention was given to methods which would be generally applicable to a large number of dwellings already existing. Results are reported of a pilot study with six small houses with established high radon concentrations

Electronic structure of chromium-doped lead telluride-based diluted magnetic semiconductors

International Nuclear Information System (INIS)

Skipetrov, E.P.; Pichugin, N.A.; Slyn'ko, E.I.; Slyn'ko, V.E.

2011-01-01

The crystal structure, composition, galvanomagnetic and oscillatory properties of the Pb 1-x-y Sn x Cr y Te (x = 0, 0.05-0.30, y ≤ 0.01) alloys have been investigated with varying matrix composition and chromium impurity concentration. It is shown that the chromium impurity atoms dissolve in the crystal lattice at least up to 1 mol.%. The following increase of the chromium concentration leads to the appearance of microscopic regions enriched with chromium and inclusions of Cr-Te compounds. A decrease of the hole concentration, a p-n-conversion of the conductivity type and a pinning of the Fermi level by the chromium resonant level are observed with increasing chromium content. Initial rates of changes in the free carrier concentration on doping are determined. The dependences of electron concentration and Fermi level on tin content are calculated by the two-band Kane dispersion relation. A diagram of electronic structure rearrangement for the chromium-doped alloys with varying the matrix composition is proposed.

Effects of chromium on the immune system.

Science.gov (United States)

Shrivastava, Richa; Upreti, R K; Seth, P K; Chaturvedi, U C

2002-09-06

Chromium is a naturally occurring heavy metal found commonly in the environment in trivalent, Cr(III), and hexavalent, Cr(VI), forms. Cr(VI) compounds have been declared as a potent occupational carcinogen among workers in chrome plating, stainless steel, and pigment industries. The reduction of Cr(VI) to Cr(III) results in the formation of reactive intermediates that together with oxidative stress oxidative tissue damage and a cascade of cellular events including modulation of apoptosis regulatory gene p53, contribute to the cytotoxicity, genotoxicity and carcinogenicity of Cr(VI)-containing compounds. On the other hand, chromium is an essential nutrient required to promote the action of insulin in body tissues so that the body can use sugars, proteins and fats. Chromium is of significant importance in altering the immune response by immunostimulatory or immunosuppressive processes as shown by its effects on T and B lymphocytes, macrophages, cytokine production and the immune response that may induce hypersensitivity reactions. This review gives an overview of the effects of chromium on the immune system of the body. Copyright 2002 Federation of European Microbiological Societies

Investigation of indoor radon concentration in block houses in Omderman

International Nuclear Information System (INIS)

Ahmed, H. A. M.

2010-12-01

Radon is one of the naturally occurring radioactive elements in the environment as a member of the natural uranium decay. Exposure to radon in the home and workplace is one of the main risks of ionizing radiation thought to cause tens of thousands of deaths from lung cancer each year. In order to reduce this burden it is important that national authorities have methods and tools bases on solid scientific evidence and sound public health policy. The public needs to be aware of radon risks and the means to reduce and prevent these. This study presents of the studies dealing with the investigation of exposure from ionizing radiation. The radon levels in some selected type of building styles (Bricks Albulk) were investigated in Omderman city (public housing). The radon level in most of the houses found to range between 87.63 and 206 Bq/m 3 with average value of 127±23 Bq/m 3 . This is well lay within the allowable limit with average. The study indicates that building materials used does not add significant concentration of radon to indoor. It can be considered as safe type of building style from radiation protection point of view. (Author)

SCIENCE AND TECHNOLOGY ACTIVITIES FOR CHROMIUM IN THE 100 AREAS

Energy Technology Data Exchange (ETDEWEB)

PETERSEN SW

2009-07-02

{sm_bullet} Primary Objective: Protect the Columbia River - Focus is control and treatment of contamination at or near the shoreline, which is influenced by bank storage {sm_bullet} Secondary Objective: Reduce hexavalent chromium to <48 parts per billion (ppb) in aquifer (drinking water standard) - Large plumes with isolated areas of high chromium concentrations (> 40,000 ppb), - Unknown source location(s); probably originating in reactor operation areas

Origin of hexavalent chromium in groundwater

DEFF Research Database (Denmark)

Kazakis, N.; Kantiranis, N.; Kalaitzidou, K.

2017-01-01

Hexavalent chromium constitutes a serious deterioration factor for the groundwater quality of several regions around the world. High concentrations of this contaminant have been also reported in the groundwater of the Sarigkiol hydrological basin (near Kozani city, NW Greece). Specific interest w...

Study tube housing leakage of 111 conventional diagnostic X-ray machines using ion chamber survey meter

International Nuclear Information System (INIS)

Lalrinmawia, Jonathan; Tiwari, Ramesh Chandra; Pau, Kham Suan

2018-01-01

This study aims at measuring the leakage radiation from X-ray tube and compare to national and international safety standard. The leakage radiation is formed at the anode inside the X-ray tube and transmitted through the tube housing. The tube housing is proposed to protect both patients and workers from leakage radiation. To the best of the authors' knowledge, no tube housing leakage measurements have been done so far in the present study area

A study on radiation energy of Pyramidal shape 1- Effect of housing within a Pyramid model on cancer growth and some blood parameters of mice

International Nuclear Information System (INIS)

El-Abiad, N.M.; Lotfi, S.A.; El Hadary, A.A.; Nagi, G.A.

2010-01-01

A study of solid tumor growth retardation by impaling the pyramid energy radiation in a pyramidal model shape was carried out. The great Pyramid of Egypt has evoked a keen interest since 1920, both for its architectural, marvel and mystical significance. Its strange thing (via shaping of razers, longer shelf life of vegetables, alerted states of consciousnesses, sleeping in hum and, wound healing). Power energy radiations are said to occur within a pyramid constructed in the exact geometric properties of Giza pyramid. The effect of housing in two different pyramidal shapes on cancer growth and some blood physiological indices in mice infected with cancer were observed. The results obtained that housing in pyramid shape cage significantly reduced the development of cancer, significant increase in liver enzymes activity and α feto proteins, however, no effect was observed in levels of thyroid hormones concentration when compared with their matched value in ordinary 2 inverted pyramid cages. It could be concluded that the radiation energy of pyramidal shapes might improve certain biochemical and physiological indices leading to tumor growth retardation

Advances In Hexavalent Chromium Removal At Hanford

International Nuclear Information System (INIS)

Neshem, D.O.; Riddelle, J.

2012-01-01

At the Hanford Site, chromium was used as a corrosion inhibitor in the reactor cooling water and was introduced into the groundwater as a result of planned and unplanned discharges from reactors during plutonium production since 1944. Beginning in 1995, groundwater treatment methods were evaluated leading to the use of pump and treat facilities with ion exchange using Dowex 21 K, a regenerable strong base anion exchange resin. This required regeneration of the resin, which is currently performed offsite. Resin was installed in a 4 vessel train, with resin removal required from the lead vessel approximately once a month. In 2007, there were 8 trains (32 vessels) in operation. In 2008, DOE recognized that regulatory agreements would require significant expansion in the groundwater chromium treatment capacity. Previous experience from one of the DOE project managers led to identification of a possible alternative resin, and the contractor was requested to evaluate alternative resins for both cost and programmatic risk reductions. Testing was performed onsite in 2009 and 2010, using a variety of potential resins in two separate facilities with groundwater from specific remediation sites to demonstrate resin performance in the specific groundwater chemistry at each site. The testing demonstrated that a weak base anion single-use resin, ResinTech SIR-700, was effective at removing chromium, had a significantly higher capacity, could be disposed of efficiently on site, and would eliminate the complexities and programmatic risks from sampling, packaging, transportation and return of resin for regeneration. This resin was installed in Hanford's newest groundwater treatment facility, called 100-DX, which began operations in November, 2010, and used in a sister facility, 100-HX, which started up in September of 2011. This increased chromium treatment capacity to 25 trains (100 vessels). The resin is also being tested in existing facilities that utilize Dowex 21 K for

Chromium evaluation in work atmospheres in an industry of tanneries and one of galvanoplasty

International Nuclear Information System (INIS)

Agudelo V, Sonia; Duarte Martha

1994-01-01

In tannery and galvanoplasty industries situated in Bogota (Colombia) hexavalent chromium and total soluble chromium were determinate in air samples in order to evaluated occupational exposition and risks for the worker of these factories. Samples were collected by suction pumps located near the breathing space of workers using PVC filters as captors. Samples were collected following the methodology of partial consecutive periods. Determination of Cr (VI) was done calorimetrically. Total soluble chromium was determinate by flame atomic absorption, previous optimization of procedures. Results for tannery Cr (VI) are located in the range non-detectable to 9.4 /m3 total soluble chromium was found between non detectable and 74.0 /m3. Cr (VI) in galvanoplasty varies between non detectable and 500 /m3. Probability of occupational risk were found in tannery and galvanoplasty industries

[Biological significance of chromium III for the human organism].

Science.gov (United States)

Piotrowska, Anna; Pilch, Wanda; Tota, Łukasz; Nowak, Gabriel

2018-03-09

Currently, chromium is probably the most controversial transition metal. In recent publications it is clearly stated that it is not an essential micronutrient and should be considered to have a pharmacological effect. Conflicting scientific reports along with a huge amount of dietary supplements, as well as dietary and sports nutrients available on the market have prompted the authors to investigate the available information on the range of possible application, efficacy and safety of products containing salts or chelates of chromium III. The authors reviewed articles in electronic databases for the years 1959-2016, and selected works describing the biochemical, physiological and toxic properties of chromium salts and chelates and the range of possible applications in medicine, dietetics and sport. A critical analysis of reports dealing with the effect of chromium on the carbohydrate and lipid metabolism, body composition, lean body mass and sports performance was carried out. The authors indicated papers analyzing the mechanism of action of chromium in the cognitive and affective disorders. Much attention has been paid to the safety use of chromium III supplements. There are still some unsolved issues. In the field of toxicology, a limited number of reports about environmental exposure to trivalent chromium in the workplace draws our attention. In the field of biochemical research, there is still a need to clarify the mechanism of psychiatric and endocrinological activity, especially in conjunction with the immune system. Med Pr 2018;69(2):211-223. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Stabilization of carbon dioxide and chromium slag via carbonation.

Science.gov (United States)

Wu, Xingxing; Yu, Binbin; Xu, Wei; Fan, Zheng; Wu, Zucheng; Zhang, Huimin

2017-08-01

As the main greenhouse gas, CO 2 is considered as a threat in the context of global warming. Many available technologies to reduce CO 2 emission was about CO 2 separation from coal combustion and geological sequestration. However, how to deal with the cost-effective storage of CO 2 has become a new challenge. Moreover, chromium pollution, the treatment of which requires huge energy consumption, has attracted people's widespread attention. This study is aimed to develop the sequestration of CO 2 via chromium slag. A dynamic leaching experiment of chromium slag was designed to testify the ability of CO 2 adsorption onto chromium slag and to release Cr(VI) for stabilization. The results showed that the accumulative amounts of Cr(VI) were ca. 2.6 mg/g released from the chromium slag after 24 h of leaching. In addition, ca. 89 mg/g CO 2 was adsorbed by using pure CO 2 in the experiment at 12 h. Calcite is the only carbonate species in the post-carbonated slag analyzed by powder X-ray diffraction and thermal analysis. The approach provides the feasibility of the utilization of chromium slag and sequestration of the carbon dioxide at the same time at ordinary temperatures and pressures.

Housing markets and housing policies in India

OpenAIRE

Tiwari, Piyush; Rao, Jyoti

2016-01-01

Issues of housing in India are synonymous with ignorance of housing in active government involvement at the policy and program formulation levels. They are also due to the problems that unplanned urbanization, income disparity, poverty, illiteracy, and unemployment brought. These issues extenuated the housing problem, causing a housing shortage of 51 million in 2011. Though India has a long history of establishing policies, programs, and institutions to cater to housing, without allocating ad...

Chromium Enrichment on P11 Ferritic Steel by Pack Cementation

Directory of Open Access Journals (Sweden)

Fauzi F. A.

2016-01-01

Full Text Available The future thermal power plant is expected to operate at higher temperature to improve its efficiency and to reduce greenhouse gas emission. This target requires better corrosion properties of ferritic steels, which commonly used as materials for superheater and reheater of boiler tubes. In this work, chromium enrichment on the surface of ferritic steel is studied. The deposited chromium is expected to become a reservoir for the formation of chromia protective layer. Chromium was deposited on the substrate of steel by pack cementation process for two hours at the temperature of 850ºC, 950ºC and 1050ºC, respectively. XRD analysis indicated that chromium was successfully deposited at all temperatures. Somehow, SEM cross sectional image showed that continuous layer of chromium was not continuously formed at 850oC. Therefore, this research clarify that chromium enrichment by pack cementation may be conducted at the temperature above 950°C.

Bioavailability of a potato chromium complex to the laboratory rat

International Nuclear Information System (INIS)

Gilbert, H.K.

1985-01-01

Research objectives were to study the effect of food source, preparation method and chemical form on bioavailability of chromium. Chromium concentration in potatoes was determined and tubers labeled either intrinsically or extrinsically with radioactive chromate. A labeled chromium complexes was isolated from preparations of raw, baked or fried potatoes and chromatographed on gel permeation media. Availability of the potato chromium complex to the rat was examined in three feeding studies. Animals were dosed with radioactive extrinsically or intrinsically labeled potato extract or with chromate. A labeled chromium complex was isolated from gastrointestinal contents of rats and chromatographed. Potato pulp and peel contained 1.63 and 2.70 μg Cr/g tissue respectively. True and apparent absorption from extrinsically labeled feedings were 33.4 +/- 4.7 and 29.8 +/- 11.2% respectively, and no differences existed between absorption from raw and cooked potatoes. Absorption from the extrinsic labeled potatoes differed significantly from absorption of inorganic chromatium. Apparent absorption of raw (11.1 +/- 7.9%) and cooked (-0.7 +/- 2.8%) intrinsically labeled feedings differed significantly. Absorption of inorganic chromium was 17.8% (true) and 11.5% (apparent). Examination of the chromium complex isolated from gastrointestinal tract contents showed enlargement of the complex in the stomach after consumption

Improvement of performance of the HARBEMAN house; Habiman hausu no seino kaizen ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Saito, T. [Tohoku Univ., Sendai (Japan). Dept. of Aeronautics and Space Eng.; Fujino, T. [Mitsubishi Heavy Industires Ltd., Tokyo (Japan)

1998-12-05

A natural energy autonomous house (HARBEMAN house) was built in 1996 in Sendai. This house combinedly utilizes solar thermal, photovoltaic, sky radiation cooling, rainwater energies and so on. In order to utilize a lot kind of natural energies more efficiently, we will improve thermal performance of the solar collector, the sky radiator, and so on. The effect of thermal insulation, tank size, and window glazing on thermal performance will also be examined. This article reports on the improved performance of the HARBEMAN house. (author)

21 CFR 73.3110a - Chromium-cobalt-aluminum oxide.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium-cobalt-aluminum oxide. 73.3110a Section... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Medical Devices § 73.3110a Chromium-cobalt-aluminum oxide. (a) Identity. The color additive chromium-cobalt-aluminum oxide (Pigment Blue 36) (CAS Reg. No...

Removal of Chromium and Lead from Industrial Wastewater Using

Directory of Open Access Journals (Sweden)

Mohamed Hilal

2013-04-01

Full Text Available In this research an attempt is made on the ability of aerobic treatment of synthetic solutions containing lead and chromium using effective microorganisms within the reactor. To achieve the desired objectives of the research, synthetic aqueous solutions of lead and chromium was used in the concentration of chromium and lead ions of 5, 10,50 and 100 mg / l .The work was done at constant pH equal to 4.5 and temperature of 30 ± 1 º C. Effective microorganisms solutions was added to the reactor at Vol.% of 1/50 ,1/100 ,1/500 and 1/1000, with retention time was 24 hours to measure the heavy metals concentration the atomic absorption device was used. The experimental results showed that each 1mg / l of lead and chromium ions need 24 mg of effective microorganisms to achieve removal of 92.0% and 82.60% for lead and chromium respectively. Increasing the concentration of effective microorganisms increases the surface of adsorption and thus increasing the removal efficiency. It is found that the microorganisms activity occur in the first five hours of processing and about 94% of adsorption capacity of biomass will take place. It is also found the selectivity of microorganisms to lead ions is higher than for chromium ions.

Chromium (V) compounds as cathode material in electrochemical power sources

Science.gov (United States)

Delnick, F.M.; Guidotti, R.A.; McCarthy, D.K.

A cathode for use in a thermal battery, comprising a chromium (V) compound. The preferred materials for this use are Ca/sub 5/(CrO/sub 4/)/sub 3/Cl, Ca/sub 5/(CrO/sub 4/)OH, and Cr/sub 2/O/sub 5/. The chromium (V) compound can be employed as a cathode material in ambient temperature batteries when blended with a suitably conductive filler, preferably carbon black.

Biosorption and biotransformation of chromium by Serratia sp. isolated from tannery effluent.

Science.gov (United States)

Srivastava, Shaili; Thakur, Indu Shekhar

2012-01-01

A bacterium isolated from soil and sediment ofa leather tanning mill's effluent was identified as Serratia sp. by the analysis of 16S rDNA. Scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) and transmission electron microscopy (TEM) were used to assess morphological changes and confirm chromium biosorption in Serratia sp. both in a shake-flask culture containing chromium and in a tannery wastewater. The SEMEDX and the elemental analysis of the chromate-containing samples confirmed the binding of chromium with the bacterial biomass. The TEM exhibited chromium accumulation throughout the bacterial cell, with some granular deposits in the cell periphery and in the cytoplasm. X-ray diffraction analysis (XRD) was used to quantify the chromium and to determine the chemical nature of the metal-microbe interaction. The XRD data showed the crystalline character of the precipitates, which consisted of mainly calcium chromium oxide, chromium fluoride phosphate and related organo-Cr(III) complex crystals. The XRD data also revealed a strong involvement of cellular carboxyl and phosphate groups in chromium binding by the bacterial biomass. The results of the study indicated that a combined mechanism of ion-exchange, complexation, croprecipitation and immobilization was involved in the biosorption of chromium by bacterial cells in contaminated environments.

Housing for a radioactive source

International Nuclear Information System (INIS)

Domnanovich, J. R.; Erwin, W. D.

1985-01-01

The radioactive structure comprises a radioactive source surrounded by a housing. The housing contains a first and second shielding body and a connecting device. The first shielding body has a protrusion which contains a first recess for receiving the radioactive source. The second shielding body has a second recess in one face end which accommodates the protrusion and a conical aperture communicating with the second recess in another face end. The connecting device connects the first shielding body to the second shielding body. When the radioactive source is inserted into the first recess and when the protrusion is located in the second recess, the radioactive source emits radiation primarily through the conical aperture into the environment. The source preferably contains americium which emits gamma radiation. The structure may be used as a motion correction sensor or as a marker in a nuclear diagnostic imaging

Chromium and aging

Science.gov (United States)

Aging is associated with increased blood glucose, insulin, blood lipids, and fat mass, and decreased lean body mass leading to increased incidences of diabetes and cardiovascular diseases. Improved chromium nutrition is associated with improvements in all of these variables. Insulin sensitivity de...

Population doses from naturally occurring radiation in Norway

International Nuclear Information System (INIS)

Stranden, E.

The main purpose of this work was to study the radiological consequences of the introduction of building materials with high concentrations of radioactivity and to analyse the impact of a reduction of the ventilation rates in houses on the population dose from inhalation of natural airborne radioactivity. The general problems of radioactivity in building materials are discussed. Measurements of radioactivity in building materials from different parts of the country are reported, together with theoretical calculations of the gamma doses in houses. These calculations are compared with experimental results and earlier measurements of the indoor gamma radiation in Norway. Measurements of the outdoor gamma radiation in different parts of Norway are presented. These results are used together with earlier measurements of the gamma radiation inside houses to calculate the average, and variations of population dose from this radiation. An experimental study on the radon concentrations inside different types of dwellings, and a discussion of the respiratory dose received by the inhalation of radon daughters is presented. Some factors that may have influence upon the radon concentrations are also discussed. A method for measurement of radon and thoron daughters in air is discussed. The possible radiological effects of an increased radon concentration in houses are discussed. (Auth.)

Void swelling in fast reactor irradiated high purity binary iron-chromium alloys

International Nuclear Information System (INIS)

Little, E.A.; Stow, D.A.

The void swelling characteristics of a series of high purity binary iron-chromium alloys containing 0 - 615 0 C. The void swelling behaviour can be qualitatively rationalized in terms of point defect trapping and precipitation processes involving chromium atoms

House characteristics associated with gamma radiation and radon daughter working levels in eastern Pennsylvania

International Nuclear Information System (INIS)

Stebbings, J.H.; Dignam, J.J.; Reilly, M.A.; Gerusky, T.M.; Hartman, T.T.; Anast, G.A.

1987-01-01

Working levels (WL) of radon daughters and γ measurements in basements are described for ∼1200 houses near the Reading Prong. House variables studied included condition and construction materials of basement floors and walls, basement heights and areas, heating systems, air conditioning, water supply, and presence of drains and sump pumps. WL's were poorly predicted by house characteristics or γ measurements, while γ levels were well predicted by house characteristics and WL. Except for windowless basements, associated with both high γ andl high WL measurements, factors predicting high γ levels tended to be associated with low WL's and vice versa. Dirt basement floors and fieldstone basement walls were strongly associated with high γ levels, as were poor wall conditions in multivariate analyses. Gamma levels were low in electrically heated homes. High WL's were strongly associated with electric heat, low WL's with basement walls of fieldstone and/or in poor condition. Large house volumes and well water supply were also associated with higher WL's. 4 refs., 1 fig., 4 tabs

Adsorption and desorption of hydrolyzed metal ions. 3. Scandium and chromium

International Nuclear Information System (INIS)

Gray, B.; Matijevic, E.; Clarkson Univ., Potsdam, NY

1987-01-01

Adsorption of scandium(III) and chromium(III) species on a PVC latex was measured using radioactive isotopes; the uptake increased with increasing pH. The data were interpreted by combining aspects of the models of James and Healy and also of Anderson and Bockris. The experimental and calculated results agree quite well for scandium, but not for chromium. The deviation in the latter case is believed to be due to polymerization of the hydrolyzed chromium cations and to the interaction of chromium with the anionic surface groups of the latex. Neither of these interactions occur with scandium. Hydrolyzed scandium species adsorbed on the latex were removed by acidifying the dispersion, while chromium complexes were not, substantiating the proposed difference in the chemical nature of chromium and scandium species at the solid/solution interface. 32 refs.; 8 figs.; 8 tabs

Adsorption of Chromium from Aqueous Solution Using Polyaniline

Directory of Open Access Journals (Sweden)

Majid Riahi Samani

2011-10-01

Full Text Available New group of polymers have been synthesized that are conductive of electricity so they are called conducting polymers. One of the most conducting polymers is "polyaniline". In the present study, polyaniline was synthesized by oxidizing aniline monomer under strongly acidic conditions using potassium iodate as an initiator of oxidative polymerization. Synthesized polyaniline as a powder used as an adsorbent to remove chromium from aqueous solution. Experiments were conducted in batch mode with variables such as amount of polyaniline, chromium solution pH and adsorbtion isotherms. Due to presence of Cr (III in solution after using polyaniline, removal mechanism is the combination of surface adsorption and reduction. It seems that polyaniline reduces the Cr(VI to Cr(III and adsorbs the Cr(III and a part of remaining  Cr(VI. It is well known that nitrogen atom in compounds of amine derivative makes co-ordinate bond with positive charge of metals due to the presence of electron in sp3 orbital of nitrogen. The majority of total chromium removal  occurred at 30minute for polyaniline  and the optimum  time for  hexavalent chromium  removal was about 5 min. Polyaniline has the maximum total cheomiume removal at pH, 3-9. The maximum hexavalent chromium removal occurred at acidic pH for polyanilines. The equilibrium adsorption data for polyaniline fitted both Freundlich’s and Langmuir’s isotherms. This research shows that polyaniline can be used as an adsorbent  for removal chromium from aqueous solution.

Biosorption of chromium by mangrove-derived Aplanochytrium sp ...

African Journals Online (AJOL)

The microbial dried biomass of Thraustochytrids is used as bioadsorbent for the removal of the chromium in aqueous solution. In this investigation, three species of Thraustochydrids namely Aplanochytrium sp., Thraustochytrium sp. and Schizochytrium sp. were tested for the efficiency of chromium accumulation by culturing ...

Study of Physical modifications induced by chromium doping of uranium dioxide

International Nuclear Information System (INIS)

Fraczkiewicz, M.

2010-01-01

Improvement of nuclear fuel performances requires reducing fission gas release. Doping uranium dioxide with chromium is the improvement axis considered in this work. Indeed, chromium fastens crystal growth in UO 2 , and thus enables a significant increase of the grain size. This work aims at the identification of defects produced by chromium addition in UO 2 , and their impact on properties of interest of the material. First, defects existing in doped fuel directly after sintering have been studied. X-ray Absorption Spectroscopy allowed the identification of the environment of solubilised chromium in UO 2 . Chromium atoms are roughly substituting for uranium atoms, but generate a complete reorganisation of neighbouring oxygen atoms, and distortion of uranium sublattice. Characterisation of transport properties (electrical conductivity and oxygen self-diffusion) have shown that because of charge balance, chromium plays a leading role on such properties. A model of point defects in UO 2 has been proposed, showing how complex the involved phenomena are. Observations by Transmission Electron Microscopy of ion-irradiated thin foils have shown that chromium makes the coalescence of irradiation defects easier. This behaviour can be explained by a stabilisation of defect clusters due to precipitation of chromium. Finally, study of thermal diffusion of helium in doped UO 2 , performed by Nuclear Reaction Analysis, has confirmed this interaction between chromium atoms and irradiation defects. Indeed, μ-NRA measures have shown no fast gas diffusion close to grain boundaries, in contrast with standard UO 2 behaviour, which is associated with defects recovery in grain boundaries. (author) [fr

Chromium speciation in environmental samples using a solid phase spectrophotometric method

Science.gov (United States)

Amin, Alaa S.; Kassem, Mohammed A.

2012-10-01

A solid phase extraction technique is proposed for preconcentration and speciation of chromium in natural waters using spectrophotometric analysis. The procedure is based on sorption of chromium(III) as 4-(2-benzothiazolylazo)2,2'-biphenyldiol complex on dextran-type anion-exchange gel (Sephadex DEAE A-25). After reduction of Cr(VI) by 0.5 ml of 96% concentrated H2SO4 and ethanol, the system was applied to the total chromium. The concentration of Cr(VI) was calculated as the difference between the total Cr and the Cr(III) content. The influences of some analytical parameters such as: pH of the aqueous solution, amounts of 4-(2-benzothiazolylazo)2,2'-biphenyldiol (BTABD), and sample volumes were investigated. The absorbance of the gel, at 628 and 750 nm, packed in a 1.0 mm cell, is measured directly. The molar absorptivities were found to be 2.11 × 107 and 3.90 × 107 L mol-1 cm-1 for 500 and 1000 ml, respectively. Calibration is linear over the range 0.05-1.45 μg L-1 with RSD of <1.85% (n = 8.0). Using 35 mg exchanger, the detection and quantification limits were 13 and 44 ng L-1 for 500 ml sample, whereas for 1000 ml sample were 8.0 and 27 ng L-1, respectively. Increasing the sample volume can enhance the sensitivity. No considerable interferences have been observed from other investigated anions and cations on the chromium speciation. The proposed method was applied to the speciation of chromium in natural waters and total chromium preconcentration in microwave digested tobacco, coffee, tea, and soil samples. The results were simultaneously compared with those obtained using an ET AAS method, whereby the validity of the method has been tested.

Synthesis and characterization of chromium doped boehmite nanofibres

International Nuclear Information System (INIS)

Yang Jing; Frost, Ray L.; Yuan Yong

2009-01-01

Thermogravimetric and differential thermogravimetric analysis has been used to study synthesised chromium doped boehmite. The dehydroxylation temperature increases significantly from 0 to 5% doping, after which the dehydroxylation temperature shows a small steady increase up to the 20% doping level. The temperature of dehydroxylation increases with time of hydrothermal treatment. Chromium doped boehmite nanofibres were also characterised by X-ray diffraction and transmission electron microscopy. Hydrothermal treatment of doped boehmite with chromium resulted in the formation of nanofibres over a wide dopant range. Nanofibres up to 500 nm in length and between 4 and 6 nm in width were produced

Natural background radiation intensity inside and outside a highland Tibetan private house (I)

International Nuclear Information System (INIS)

Noguchi, Kunikazu; Kudo, Itsuro; Okano, Masaharu

1998-01-01

The radiation exposure rates were measured inside and outside a private house in the Tibetan Autonomous Region of China. As far as seen from the cosmic ray exposure rate and the gamma ray exposure rate, the indoor exposure rates can be classified into 3 groups: the 2nd floor, entrance to the 1st floor and in the rest of the 1st floor. In the 1st group, the mean cosmic ray exposure rate was 4.079 nC/kg/h (15.81 μR/h) and the mean gamma ray exposure rate was 4.515 nC/kg/h (17.50 μR/h). In the 3rd group, the mean cosmic ray exposure rate was 2.740 nC/kg/h (10.62 μR/h) and the mean gamma ray exposure rate was 5.284 nC/kg/h (20.48 μR/h). The reason why the cosmic ray exposure rate in the 3rd group is lower than in the 1st group is believed to be that cosmic rays are cut off by the construction materials. The reasons why the gamma ray exposure rate in the 3rd group is higher than in the 1st group are believed to be that the 3rd group is nearer to the ground than the 1st group and the stones of which the 1st floor walls are made have a higher concentration of natural radionuclides than the earth of which the 2nd floor walls are made. Both the cosmic ray exposure rate and the gamma ray exposure rate in the 2nd group are between those of the 1st group and the 3rd group. Furthermore, the authors calculated the air absorbed dose rates inside and outside a Tibetan private house and compared them with those of private houses in the world. (author)

The personnel protection system for a Synchrotron Radiation Accelerator Facility: Radiation safety perspective

International Nuclear Information System (INIS)

Liu, J.C.

1993-05-01

The Personnel Protection System (PPS) at the Stanford Synchrotron Radiation Laboratory is summarized and reviewed from the radiation safety point of view. The PPS, which is designed to protect people from radiation exposure to beam operation, consists of the Access Control System (ACS) and the Beam Containment System (BCS), The ACS prevents people from being exposed to the very high radiation level inside the shielding housing (also called a PPS area). The ACS for a PPS area consists of the shielding housing and a standard entry module at every entrance. The BCS prevents people from being exposed to the radiation outside a PPS area due to normal and abnormal beam losses. The BCS consists of the shielding (shielding housing and metal shielding in local areas), beam stoppers, active current limiting devices, and an active radiation monitor system. The system elements for the ACS and BCS and the associated interlock network are described. The policies and practices in setting up the PPS are compared with some requirements in the US Department of Energy draft Order of Safety of Accelerator Facilities

Effects of UV light and chromium ions on wood flavonoids

International Nuclear Information System (INIS)

Molnárné Hamvas, L.; Németh, K.; Stipta, J.

2003-01-01

The individual and simultaneous effect of UV light and chromium ions was investigated by spectrophotometric methods on inert surfaces impregnated with quercetin or robinetin. The UV-VIS spectra of the silica gel plates impregnated with these flavonoids were modified characteristically after irradiating ultraviolet light. Even a half an hour of irradiation has caused irreversible changes in the molecule structure. A certain chemical - presumably complexation - was concluded from the change of spectral bands assigned to flavonoids when impregnated with chromic ions. Hexavalent chromium caused more complex changes in the absorption spectra. The differences in the spectra could indicate either the oxidation and decomposition of flavonoids, or some kind of coordination process and the reduction of hexavalent chromium. The simultaneous application of UV light and chromium ions caused more pronounced effects. The complexation process between chromium(III) and flavonoid was completed

Chromium supplements for glycemic control in type 2 diabetes: limited evidence of effectiveness

Science.gov (United States)

Dwyer, Johanna T.; Bailey, Regan L.

2016-01-01

Some adults with type 2 diabetes mellitus (T2DM) believe that chromium-containing supplements will help control their disease, but the evidence is mixed. This narrative review examines the efficacy of chromium supplements for improving glycemic control as measured by decreases in fasting plasma glucose (FPG) or hemoglobin A1c (HbA1c). Using systematic search criteria, 20 randomized controlled trials of chromium supplementation in T2DM patients were identified. Clinically meaningful treatment goals were defined as an FPG of ≤7.2 mmol/dL, a decline in HbA1c to ≤7%, or a decrease of ≥0.5% in HbA1c. In only a few randomized controlled trials did FPG (5 of 20), HbA1c (3 of 14), or both (1 of 14) reach the treatment goals with chromium supplementation. HbA1c declined by ≥0.5% in 5 of 14 studies. On the basis of the low strength of existing evidence, chromium supplements have limited effectiveness, and there is little rationale to recommend their use for glycemic control in patients with existing T2DM. Future meta-analyses should include only high-quality studies with similar forms of chromium and comparable inclusion/exclusion criteria to provide scientifically sound recommendations for clinicians. PMID:27261273

Chromium tolerance and reduction potential of Staphylococci ...

African Journals Online (AJOL)

In order to study the microbiology of chromium tolerance and reduction at a fly ash dumping site in South Africa, 15 core samples were investigated. It was shown that the 30 year old dumping site exhibited high concentrations of Cr (VI) ranging from 1.6 to 9.6 mg/g. From this contaminated fly ash dumping site, 67 chromium ...

A new method in estimation of total hexavalent chromium in Portland pozzolan cement

International Nuclear Information System (INIS)

Sharma, R.; Sharma, D.

2017-01-01

Variamine blue was used first time for the detection of hexavalent chromium from cement samples. In present method, cement was treated sequentially with water, sulphate and carbonate buffer to extract soluble, sparingly soluble and insoluble hexavalent chromium respectively. Extracted Cr (VI) was determined using variamine blue as chromogenic reagent. The determination is based on the reaction of hexavalent chromium with potassium iodide in an acid medium to liberate iodine. This oxidizes variamine blue to form a violet coloured species having an absorption to maximum at 556 nm. Energy-dispersive X-ray spectroscopy (EDX) and Infrared Spectroscopy (IR) confirmed the complete extraction of hexavalent chromium by sequential extraction process. SRM 2701 (Reference material from NIST, USA) was used for revalidating the results. The percentage of recovery for proposed and reference method (diphelycarbazide method) varied from 98.5 to 101 and 97.5 to 100.5. Whereas, their relative error percentage varied from -1.5 to 0.33 and -2.5 to 0.5. [es

Concentrations of chromium, manganese, and lead in air and in avian eggs

International Nuclear Information System (INIS)

Hui, C.A.

2002-01-01

Embryo exposure was not directly related to tropospheric levels of chromium, manganese or lead. - The expansion of urbanization introduces air pollution to wildlife areas. Some metal contaminants occurring in concentrations too small to have any measurable impact on adult birds may seriously affect embryos that are more sensitive to contaminants than the adult. Chromium, manganese, and lead are toxic and can be passed from the hen to the egg. This study relates the concentrations of these metals in eggs to their concentrations in air in three cities. Rock dove eggs were sampled and air pollution records were examined in the California cities of Riverside, Los Angeles, and San Francisco. The eggs from San Francisco did not differ from those of Los Angeles in lead concentration but the air did differ. The eggs collected in Los Angeles in 1998 had concentrations of chromium greater than in those from Riverside and from Los Angeles 1999 but the air had concentrations of chromium that did not differ among those three collections. Concentrations of manganese did not differ among the eggs but did differ among the air samples of the three cities. Exposures of embryos to chromium and manganese in this study were not at levels warranting concern. Although the concentration at which lead in eggs impairs avian health is not established, the highest concentrations found in this study exceed estimated safe concentrations. There is no indication that embryo exposure is directly related to atmospheric levels of these metals in the cities of this study

Mechanical-thermal synthesis of chromium carbides

International Nuclear Information System (INIS)

Cintho, Osvaldo Mitsuyuki; Favilla, Eliane Aparecida Peixoto; Capocchi, Jose Deodoro Trani

2007-01-01

The present investigation deals with the synthesis of chromium carbides (Cr 3 C 2 and Cr 7 C 3 ), starting from metallic chromium (obtained from the reduction of Cr 2 O 3 with Al) and carbon (graphite). The synthesis was carried out via high energy milling, followed by heat-treating of pellets made of different milled mixtures at 800 o C, for 2 h, under an atmosphere of argon. A SPEX CertPrep 8000 Mixer/Mill was used for milling under argon atmosphere. A tool steel vat and two 12.7 mm diameter chromium steel balls were used. The raw materials used and the products were characterized by differential thermal analysis, thermo gravimetric analysis, X-ray diffraction, electronic microscopy and X-ray fluorescence chemical analysis. The following variables were investigated: the quantity of carbon in the mixture, the milling time and the milling power. Mechanical activation of the reactant mixture depends upon the milling power ratio used for processing. The energy liberated by the reduction of the chromium oxide with aluminium exhibits a maximum for milling power ratio between 5:1 and 7.5:1. Self-propagating reaction occurred for all heat-treated samples whatever the carbon content of the sample and the milling power ratio used. Bearing carbon samples exhibited hollow shell structures after the reaction. The level of iron contamination of the milled samples was kept below 0.3% Fe. The self-propagated reaction caused high temperatures inside the samples as it may be seen by the occurrence of spherules, dendrites and whiskers. The carbon content determines the type of chromium carbide formed

Radon levels reduced through venting of house foundations

International Nuclear Information System (INIS)

Sivborg, P.; Johansson, I.; Strindehag, O.

1981-01-01

It has been confirmed that the radon emanation from the ground poses a more importent radiation hazard than the radon contained in the building material. In this article a simple system for ventilation of the gases produced under the foundation of a small houses is described. This ventilation system reduced the radondaughters concentration in a house by a factor of ten. (L.E.)

Thermogravimetric studies of high temperature reactions between potassium salts and chromium

International Nuclear Information System (INIS)

Lehmusto, J.; Lindberg, D.; Yrjas, P.; Skrifvars, B.-J.; Hupa, M.

2012-01-01

Highlights: ► K 2 CO 3 reacted with Cr 2 O 3 forming K 2 CrO 4 . ► Presence of chlorine did not alone explain the initiation of accelerated oxidation. ► More light was shed to the role of chromates in accelerated oxidation. ► Accelerated oxidation of chromia protected steels occurs in two consecutive stages. ► Both potassium and chloride are required, so that both stages of reaction occur. - Abstract: This study compares the high temperature reactions of potassium chloride (KCl) and potassium carbonate (K 2 CO 3 ), two salts found in fly ashes formed in biomass combustion, with both pure metallic chromium (Cr) and chromium oxide (Cr 2 O 3 ). The reactions were investigated with thermogravimetric measurements and the results discussed based on thermodynamic calculations. In simple terms: potassium chloride reacted with chromium forming potassium chromate (K 2 CrO 4 ) and chromium oxide. Potassium chloride did not react with chromium oxide. Potassium carbonate reacted with chromium oxide, but not with chromium. The presence of potassium is sufficient to initiate accelerated oxidation, but chloride is needed to sustain it.

The impact of weather variation on energy consumption in residential houses

International Nuclear Information System (INIS)

Fikru, Mahelet G.; Gautier, Luis

2015-01-01

Highlights: • There is evidence for significant intraday variation of energy use. • The sensitivity of energy use to weather variation falls via efficiency features. • The sensitivity of energy use to weather depends on the specific time of day/night. • High frequency data helps to accurately model the energy use-weather relationship. - Abstract: This paper studies the impact of weather variation on energy use by using 5-minutes interval weather–energy data obtained from two residential houses: house 1 is a conventional house with advanced efficiency features and house 2 is a net-zero solar house with relatively more advanced efficiency features. Our result suggests that energy consumption in house 2 is not as sensitive to changes in weather variables as the conventional house. On average, we find that a one unit increase in heating and cooling degree minutes increases energy use by about 9% and 5% respectively for house 1 and 5% and 4% respectively for house 2. In addition, our findings suggest that non-temperature variables such as solar radiation and humidity affect energy use where the sensitivity rates for house 2 are consistently lower than that of house 1. Furthermore our result suggests that the sensitivity of energy use to weather depends on the season and specific time of the day/night

Review of occupational epidemiology of chromium chemicals and respiratory cancer.

Science.gov (United States)

Hayes, R B

1988-06-01

Several epidemiologic studies have investigated the association between cancer risk and employment in chromium producing and using industries. Strong and consistent associations have been found between employment in the primary chemical producing industry and the risk for respiratory cancer. Workers employed in chromate pigment production and possibly spray painters of chromate pigment paints appear to be at excess risk of respiratory cancer. Chrome platers may also be at excess risk, although the evidence is limited. A few studies indicate that chromium alloy welding may also be an exposure source of concern. Some studies of ferrochromium alloy workers have shown an excess risk for respiratory cancer, although the risk may in part be due to concomitant exposures. The evidence indicates that the hexavalent form of chromium is the primary agent of chromium carcinogenesis. Solubility and other characteristics of chromium compounds may also play a role in determining risk.

Constructing passive houses

Energy Technology Data Exchange (ETDEWEB)

Oehler, S. [Oehler Faigle Archkom Solar Architektur, Bretten (Germany)

2005-07-01

Everybody can learn to build energy-efficient. It needs theoretical and practical experience. 1997 we built the first freestanding Passive House in Europe, the Passive House Oehler. There had been a lot of questions, starting with the insecurity, whether the calculation program of the Passive House Institute, the PHPP, is working properly in our case. Nobody knew at that time because nobody tried it out before. It took us a lot of time to find out and every detail of the construction hat to be invented to meet the very high demand of thermal quality. All the following houses needed less time and had fewer open questions, adding one piece of experience with every building. 2002 we realised the biggest Passive House, the office building Energon Ulm with 420 working spaces. In the meantime we have learned a lot like how to produce prefabricated timber elements for the facades, providing good insulation, air tightness and avoiding serious thermal bridges. We have proofed, that any kind of building type can be a Passive House. And with increasing experience the freedom of design and construction is growing. Even the economical efficiency increased. The Energon Ulm is providing a much better indoor climate than any other office building and was build 10 % cheaper than an average German office building. At present the Passive House Standard is the most efficient solution for the user to live in the desired comfort zone between 20 C and 25 C. This zone of individual feeling-well can be described with the term ''operative temperature''. This term is defined by factors like air temperature, radiation temperature of warm and cold surfaces, air speed and humidity. The result of all these factors has to be within 18 C to 25 C without accepting one of the factors getting extreme.

Hexavalent Chromium IV-Free Primer Development

Science.gov (United States)

Alldredge, Michael J.; Buck, Amy L.

2015-01-01

Primer materials provide corrosion protection for metal parts as well as an increased adhesion between metallic substrates and thermal protection systems (TPSs). Current primers for use in cryogenic applications contain hexavalent chromium. This hexavalent chromium provides excellent corrosion protection even in a cryogenic environment, but it is a carcinogen that requires special equipment and waste control procedures to use. The hazardous nature of hexavalent chromium makes it an obsolescence risk in the future. This study included two phases of evaluation. Thirteen primers were initially identified as candidates and twelve of those primers were tested in phase 1. Four of the best performing candidates from phase 1 continued into phase 2 testing. Phase 1 testing consisted mostly of liquid constituent and physical property testing. Cryoflex and salt fog testing were included in phase 1 because of their importance to the overall success of a candidate material. Phase 2 consisted of physical, thermal, and mechanical properties for nominally processed and fabricated specimens.

Mechanoactivation of chromium silicide formation in the SiC-Cr-Si system

Directory of Open Access Journals (Sweden)

Vlasova M.

2002-01-01

Full Text Available The processes of simultaneous grinding of the components of a SiC-Cr-Si mixture and further temperature treatment in the temperature range 1073-1793 K were studied by X-ray phase analysis, IR spectroscopy, electron microscopy, and X-ray microanalysis. It was established that, during grinding of the mixture, chromium silicides form. A temperature treatment completes the process. Silicide formation proceeds within the framework of the diffusion of silicon into chromium. In the presence of SiO2 in the mixture, silicide formation occurs also as a result of the reduction of silica by silicon and silicon carbide. The sintering of synthesized composite SiC-chromium silicides powders at a high temperature under a high pressure (T = 2073 K, P = 5 GPa is accompanied by the destruction of cc-SiC particles, the cc/3 transition in silicon carbide and deformation distortions of the lattices of chromium silicides.

Thermodynamic Properties of Chromium Adsorption by Sediments ...

African Journals Online (AJOL)

MBI

2013-06-19

Jun 19, 2013 ... The adsorption of Chromium from aqueous solution using river Watari sediment as an adsorbent was modeled. The influence of initial ... number of metals, including chromium, copper, nickel and zinc. The ion ... through filter paper to determine the concentration ... liquid and solid phases were separated by.

LONG TERM EFFECT OF CHROMIUM ON LIPID PROFILE AND SOME HORMONES IN OBESE RATS

International Nuclear Information System (INIS)

GABR, S.A.; ABDEL-KHALEK, L.G.; GHAREIB, S.A.

2008-01-01

In the present study, the long term effect of chromium picolinate (intake 30 and 60 days) on lipid profile, testosterone, thyroid hormones, corticosterone and insulin was studied in obese male rats. A total of 48 male albino rats were arranged into four equal groups. The rats were distributed into four equal main groups: 1- Normal rats left without any treatment and served as a control group. 2- Normal rats treated with chromium picolinate at a dose of 40 μg/kg/day. 3-Obese rats (after the induction of obesity) using fed high fat diet. 4- Obese rats treated with chromium picolinate. The results obtained showed that normal rats treated with chromium picolinate for 30 or 60 days had no changes in total cholesterol, triglycerides, total lipids, LDL-cholesterol, HDL-cholesterol, triiodothyronine (T 3 ) and thyroxine (T 4 ) when compared with the control group. The testosterone and corticosterone levels were significantly decreased in rats treated with chromium picolinate for 60 days. Insulin level was significantly increased in treated rats for 60 days when compared with the control ones. In obese rats, the lipid profile and corticosterone were significantly increased at 30 and 60 days, while the insulin levels were increased in obese rats fed on high fat diet for 30 days as compared with the control rats. The administration of chromium picolinate to obese rats succeeded to decrease the lipid profile, corticosterone (at 60 days) and insuline (at 30 days) when compared with the obese rats. It could be concluded from this study that chromium picolinate possess beneficial effects in decreasing lipid profile in obese rats. Therefore, additional of chromium picolinate may be useful in obese rats to burn excess body fat and in treatment of hypercholesterolemia. Since it cause decrease in testosterone level, its use was advised to restrict to relatively old age

Chromium Resistant Bacteria: Impact on Plant Growth in Soil Microcosm

Directory of Open Access Journals (Sweden)

Sayel Hanane

2014-07-01

Full Text Available Three chromium resistant bacterial strains, Pseudomonas fluorescens PF28, Enterobacter amnigenus EA31 and Enterococcus gallinarum S34 isolated from tannery waste contaminated soil were used in this study. All strains could resist a high concentration of K2Cr2O7 that is up to 300 mg/L. The effect of these strains on clover plants (Trifolium campestre in the presence of two chromium salts CrCl3 and K2Cr2O7 was studied in soil microcosm. Application of chromium salts adversely affected seed germination, root and shoot length. Bacterial inoculation improved the growth parameters under chromate stress when compared with non inoculated respective controls. There was observed more than 50% reduction of Cr(VI in inoculated soil microcosms, as compared to the uninoculated soil under the same conditions. The results obtained in this study are significant for the bioremediation of chromate pollution.

CHROMIUM BIOACCUMULATION FROM COMPOSTS AND VERMICOMPOSTS BASED ON TANNERY SLUDGES

Directory of Open Access Journals (Sweden)

Krzysztof GONDEK

2008-07-01

Full Text Available Storage of waste substances is not indifferent to ecological equilibrium in the environment therefore should not be the ultimate way to limit waste arduousness. Therefore, the conducted investigations aimed to determine the effect of tannery composts and vermicomposts loaded with chromium on this element bioaccumulation in earthworm bodies and biomass of selected plants. Chromium in composts and vermicomposts based on tannery sludges occurred in small quantities and easily soluble compounds. Chromium concentrations in redworm biomass points to this metal accumulation in Eisenia fetida body tissues. This element content in redworm biomass was signifi cantly positively correlated with its content in composts. Chromium content in plants was diversifi ed and on treatments was generally smaller than on mineral treatment or farmyard manure. Chromium absorbed by plants was stored mainly in the root systems, and over the norm content of this element found in vermicomposts did not cause its excessive accumulation in plant biomass.

Chromium speciation in solid matrices and regulation: a review

Energy Technology Data Exchange (ETDEWEB)

Unceta, N. [University of the Basque Country, Department of Analytical Chemistry, Faculty of Pharmacy, Vitoria-Gasteiz (Spain); Seby, F. [Ultra Traces Analyses Aquitaine (UT2A), Helioparc Pau-Pyrenees, Pau (France); Malherbe, J.; Donard, O.F.X. [Universite de Pau et des Pays de l' Adour, Helioparc Pau-Pyrenees, Laboratoire de Chimie Analytique Bio-Inorganique et Environnement, IPREM, UMR CNRS 5254, Pau (France)

2010-06-15

In recent years, the extensive use of chromium in industrial processes has led to the promotion of several directives and recommendations by the European Union, that try to limit and regulate the presence of Cr(VI) in the environment and to protect industrial workers using chromium and end-users of manufactured products. As a consequence, new standard methods and analytical procedures have been published at the EU level for Cr(VI) determination in soil, sludge, sediment, and similar waste materials, workplace atmospheres, cement, packaging materials, industrially produced samples, and corrosion-protection layers on some components of vehicles and electrical and electronic equipment. The objective of this article is to summarize the different directives and recommendations and to critically review the currently existing standard methods and the methods published in the literature for chromium speciation in the above mentioned solid matrices, putting the emphasis on the different extraction procedures which have been developed for each matrix. Particular attention has been paid to Cr(III) and Cr(VI) inter-conversions that can occur during extraction and efforts to minimize these unwanted reactions. Although the use of NaOH-Na{sub 2}CO{sub 3} solutions with hot plate extraction seems to be the more widespread procedure, species transformation can still occur and several studies suggest that speciated isotope-dilution mass spectrometry (SIDMS) could be a suitable tool for correction of these interconversions. Besides, recent studies have proved the role of Cr(III) in chromium toxicology. As a consequence, the authors suggest an update of standard methods in the near future. (orig.)

Calcium alginate as an eco-friendly supporting material for Baker’s yeast strain in chromium bioremediation

Directory of Open Access Journals (Sweden)

M.S. Mahmoud

2017-12-01

Full Text Available In this study, Baker’s yeast strain (Saccharomyces cerevisiae biomass was immobilized in alginate extract 3% forming Biomass/Polymer Matrices Beads (BPMB. These beads were investigated for chromium biosorption from aqueous solution. Factors such as solution pH, contact times, temperature values, stirring rates, BPMB dosages and initial chromium ions concentrations were experimentally tested using repeated-batch process to determine the sorption capacity for chromium (VI ions. Batch experiments were conducted at pH range from 1.5 to 7.5. The optimum pH value was 3.5 for direct chromium removal. The effect of chromium concentration was studied using different concentrations from 200 to 1000 ppm. Freundlich’s isothermal model showed better representation of data than Langmuir’s isothermal model with correlation coefficient 0.922. The maximum biosorption capacity of chromium was found to be 154 mg g−1 at initial concentration 200 ppm under optimum conditions. At the end of the experiments, BPMB were investigated for chromium biosorption from tannery effluent sample. Results showed decrease in chromium concentration up to 85%. The availability of recycling of the BPMB was also studied for three subsequent cycles. The surface sequestration of metal ions by BPMB was characterized before and after metal binding using a scanning electron microscope (SEM equipped with an energy dispersive X-ray analysis (EDXA and FTIR spectroscopy in order to determine the mechanisms of chromium biosorption.

Chromium related degradation of solid oxide fuel cells; Chrom-bezogene Degradation von Festoxid-Brennstoffzellen

Energy Technology Data Exchange (ETDEWEB)

Neumann, Anita

2011-05-04

Solid Oxide Fuel Cells (SOFCs) offer a high potential for application as an auxiliary power unit (APU) for heavy goods vehicles as well as combined heat and power (CHP) systems. SOFCs are especially attractive due to their high efficiencies and the use of different fuel types. However, optimization in terms of long term stability and costs are still necessary. This work characterized the degradation of SOFCs with lanthanum strontium manganite (LSM) cathodes under chromium influence. Galvanostatic cell tests were carried out at 800 C with operation times from 250 - 3000 h and variation of the chromium source and current density. The current densities of j = 0 (A)/(cm{sup 2}), j = 0,3 (A)/(cm{sup 2}) and j = 0,5 (A)/(cm{sup 2}) were applied. The high temperature ferritic alloy Crofer22APU was used as a chromium source. Variation of the chromium source was realized by coating the Crofer22APU insert with the chromium retention layer Mn{sub 3}O{sub 4} and the cathode contact layer LCC10. Cell degradation was analyzed with regard to cell voltage, current density and area specific resistance (ASR). Microstructural alterations of the cathode as well as chromium content and distribution across the cell were investigated after completion of the cell tests. For cells with a chromium source present and operation with a nonzero current density, the course of cell degradation was divided into three phases: a run-in, weak linear degradation and strong linear degradation. A decrease of the chromium release rate by means of different coatings stretched the course of degradation along the timescale. Strong degradation, which is characterized by a significant increase in ASR as well as a decrease of current density at the operating point, was only observed when a chromium source in the setup was comb ined with operation of the cell with a non-zero current density. Operation of the cell with a chromium source but no current density caused a degradation of current density at the

Investigation of indoor radon concentration in block houses in Omderman

Energy Technology Data Exchange (ETDEWEB)

Ahmed, H A. M. [Atomic Energy Council, Sudan Academy of Sciences (SAS), Khartoum (Sudan)

2010-12-15

Radon is one of the naturally occurring radioactive elements in the environment as a member of the natural uranium decay. Exposure to radon in the home and workplace is one of the main risks of ionizing radiation thought to cause tens of thousands of deaths from lung cancer each year. In order to reduce this burden it is important that national authorities have methods and tools bases on solid scientific evidence and sound public health policy. The public needs to be aware of radon risks and the means to reduce and prevent these. This study presents of the studies dealing with the investigation of exposure from ionizing radiation. The radon levels in some selected type of building styles (Bricks Albulk) were investigated in Omderman city (public housing). The radon level in most of the houses found to range between 87.63 and 206 Bq/m{sup 3} with average value of 127{+-}23 Bq/m{sup 3}. This is well lay within the allowable limit with average. The study indicates that building materials used does not add significant concentration of radon to indoor. It can be considered as safe type of building style from radiation protection point of view. (Author)

Determination of Chromium(III) Picolinate Using High Performance Liquid Chromatography-Ultraviolet Spectrophotometry

International Nuclear Information System (INIS)

Kim, Sung Il; Woo, Dong Jin; Kang, Dae Kyung; Lee, Myung Hee; Woo, Gun Jo; Cha, Ki Won

2003-01-01

Cr-(pic) 3 has been widely used as food additives, drugs, and feed additives. Accordingly, its determination method should be established. In the present paper, we have studied the determination method of chromium(III) picolinate accurately using ESI-MS on-lined with HPLC. Chromium(III) picolinate in feed products was determined successfully. Chromium(III) is very well known as an essential mineral. It is suggested as a cofactor in the maintenance of both normal lipid and carbohydrate metabolism by assisting the action of insulin on a cell membrane. According to the National Research Council, the daily recommended intake of chromium(III) is 50-200 μg. Several organic chromium(III) complexes have been reported to have significantly higher absorption and tissue incorporation activity than inorganic salts such as chromium(III) chloride

Effect of Chromium(VI Toxicity on Enzymes of Nitrogen Metabolism in Clusterbean (Cyamopsis tetragonoloba L.

Directory of Open Access Journals (Sweden)

Punesh Sangwan

2014-01-01

Full Text Available Heavy metals are the intrinsic component of the environment with both essential and nonessential types. Their excessive levels pose a threat to plant growth and yield. Also, some heavy metals are toxic to plants even at very low concentrations. The present investigation (a pot experiment was conducted to determine the affects of varying chromium(VI levels (0.0, 0.5, 1.0, 2.0, and 4.0 mg chromium(VI kg−1 soil in the form of potassium dichromate on the key enzymes of nitrogen metabolism in clusterbean. Chromium treatment adversely affect nitrogenase, nitrate reductase, nitrite reductase, glutamine synthetase, and glutamate dehydrogenase in various plant organs at different growth stages as specific enzyme activity of these enzymes decreased with an increase in chromium(VI levels from 0 to 2.0 mg chromium(VI kg−1 soil and 4.0 mg chromium(VI kg−1 soil was found to be lethal to clusterbean plants. In general, the enzyme activity increased with advancement of growth to reach maximum at flowering stage and thereafter decreased at grain filling stage.

Effect of the gamma radiation in hydrotalcite with chromates; Efecto de la Radiacion Gamma en Hidrotalcitas con Cromatos

Energy Technology Data Exchange (ETDEWEB)

Martinez G, S. [Facultad de Ciencias, Universidad Autonoma del Estado de Mexico, Instituto Literario No. 100 Col. Centro, 50000 Toluca, Estado de Mexico (Mexico); Bulbulian, S. [ININ, Carr. Mexico-Toluca Km. 36.5, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: soniakorn@yahoo.com

2004-07-01

At the moment the generation of radioactive wastes is topic of numerous studies. In this work was retained anionic material, chromates, in hydrotalcite that are anionic exchangers. It was proposed to warm the HT at different temperatures of 600 C up to 1200 C with the purpose of immobilizing the chromium inside the hydrotalcite. To high temperatures (1000 and 1200 C) it was formed one spinel (MgCr{sub 2}O{sub 4}) that is a very stable compound. It was found that when increasing the heating temperature, the anions are retained strongly. The immobilization of the Cr was determined through the chromium lixiviation with solutions 1N and 5N of NaCl. Also it was studied the effect of the radiation on the heated materials. The radiation dose used for it was of 1000 and 6000 kGy. The results show that for the calcined samples at 1000 and 1200 C irradiated or no irradiated, the chromium is strongly retained in form of spinels that is the structure formed after the calcination of the material. (Author)

A REVIEW OF BIOSORPTION OF CHROMIUM IONS BY MICROORGANISMS

Directory of Open Access Journals (Sweden)

Inga Zinicovscaia

2012-12-01

Full Text Available Due to its widespread industrial use, chromium has become a serious pollutant in diverse environmental settings. The main source of chromium pollution including the Republic o Moldova is industry. It is a great need to develop new eco-friendly methods of chromium removal. Biosorption of heavy metals is a most promising technology involved in the removal of toxic metals from industrial waste streams and natural waters. This article is an extended abstract of a communication presented at the Conference Ecological Chemistry 2012

Structure and magnetic properties of chromium doped cobalt molybdenum nitrides

Energy Technology Data Exchange (ETDEWEB)

Guskos, Niko; Żołnierkiewicz, Grzegorz; Typek, Janusz; Guskos, Aleksander [Institute of Physics, Faculty of Mechanical Engineering and Mechatronics, West Pomeranian University of Technology, Szczecin, Piastów 48, 70-311 Szczecin (Poland); Adamski, Paweł; Moszyński, Dariusz [Institute of Inorganic Chemical Technology and Environment Engineering, West Pomeranian University of Technology, Szczecin, Pułaskiego 10, 70-322 Szczecin (Poland)

2016-09-15

Four nanocomposites containing mixed phases of Co{sub 3}Mo{sub 3}N and Co{sub 2}Mo{sub 3}N doped with chromium have been prepared. A linear fit is found for relation between Co{sub 2}Mo{sub 3}N and chromium concentrations. The magnetization in ZFC and FC modes at different temperatures (2–300 K) and in applied magnetic fields (up to 70 kOe) have been investigated. It has been detected that many magnetic characteristics of the studied four nanocomposites correlate not with the chromium concentration but with nanocrystallite sizes. The obtained results were interpreted in terms of magnetic core-shell model of a nanoparticle involving paramagnetic core with two magnetic sublattices and a ferromagnetic shell related to chromium doping. - Highlights: • A new chromium doped mixed Co-Mn-N nanocomposites were synthesized. • Surface ferromagnetism was detected in a wide temperature range. • Core-shell model was applied to explain nanocomposites magnetism.

Toxicity assessment and geochemical model of chromium leaching from AOD slag.

Science.gov (United States)

Liu, Bao; Li, Junguo; Zeng, Yanan; Wang, Ziming

2016-02-01

AOD (Argon Oxygen Decarburization) slag is a by-product of the stainless steel refining process. The leaching toxicity of chromium from AOD slag cannot be ignored in the recycling process of the AOD slag. To assess the leaching toxicity of the AOD slag, batch leaching tests have been performed. PHREEQC simulations combined with FactSage were carried out based on the detailed mineralogical analysis and petrophysical data. Moreover, Pourbaix diagram of the Cr-H2O system was protracted by HSC 5.0 software to explore the chromium speciation in leachates. It was found that AOD slag leachate is an alkaline and reductive solution. The Pourbaix diagram of the Cr-H2O system indicated that trivalent chromium, such as Cr(OH)4(-), is the major chromium species in the experimental Eh-pH region considered. However, toxic hexavalent chromium was released with maximum concentrations of 30 µg L(-1) and 18 µg L(-1) at L/S 10 and 100, respectively, during the earlier leaching stage. It concluded that the AOD slag possessed a certain leaching toxicity. After 10 d of leaching, trivalent chromium was the dominant species in the leachates, which corresponded to the results of PHREEQC simulation. Leaching toxicity of AOD slag is based on the chromium speciation and its transformation. Great attention should be focused on such factors as aging, crystal form of chromium-enriched minerals, and electrochemical characteristics of the leachates. Copyright © 2015 Elsevier Ltd. All rights reserved.

Stress corrosion cracking of Alloy 600 in primary water of PWR: study of chromium diffusion

International Nuclear Information System (INIS)

Chetroiu, Bogdan-Adrian

2015-01-01

Alloy 600 (Ni-15%Cr-10%Fe) is known to be susceptible to Stress Corrosion Cracking (SCC) in primary water of Pressurized Water Reactors (PWR). Recent studies have shown that chromium diffusion is a controlling rate step in the comprehension of SCC mechanism. In order to improve the understanding and the modelling of SCC of Alloy 600 in PWR primary medium the aim of this study was to collect data on kinetics diffusion of chromium. Volume and grain boundary diffusion of chromium in pure nickel and Alloy 600 (mono and poly-crystals) has been measured in the temperature range 678 K to 1060 K by using Secondary Ions Mass Spectroscopy (SIMS) and Glow Discharge-Optical Spectrometry (GD-OES) techniques. A particular emphasis has been dedicated to the influence of plastic deformation on chromium diffusion in nickel single crystals (orientated <101>) for different metallurgical states. The experimental tests were carried out in order to compare the chromium diffusion coefficients in free lattice (not deformed), in pre-hardening specimens (4% and 20%) and in dynamic deformed tensile specimens at 773 K. It has been found that chromium diffusivity measured in dynamic plastic deformed creep specimens were six orders of magnitude greater than those obtained in not deformed or pre-hardening specimens. The enhancement of chromium diffusivity can be attributed to the presence of moving dislocations generated during plastic deformation. (author)

Evaluation of chromium speciation and transport characteristics in the Hanford Site 100D and 100H areas

International Nuclear Information System (INIS)

Thornton, E.C.; Amonette, J.E.; Olivier, J.

1995-08-01

Field and laboratory investigations have been conducted to define the fate and transport characteristics of chromium contamination present in the 100D/H Areas of the Hanford Site. This information is relevant to assessing the impact of the release of hexavalent chromium to the Columbia River. Included in this study was the determination of the concentration and aqueous speciation of chromium in the unconfined acquifer and an assessment of potential changes in speciation as groundwater passes through the river/acquifer transition zone and mixes with the Columbia River. The results of this study indicate that chromium present within the Hanford acquifer is predominantly in the oxidized hexavalent state. Chromium is apparently stable in the oxidized form owing to its lack of organic matter within the acquifer. A portion of the chromium is removed as groundwater passes through the transition zone due to reduction and precipitation associated with sediment/water interaction processes. Chemical data collected from seep water samples, however, suggests, that most of the hexavalent chromium ultimately discharges into the Columbia River. Dilution of hexavalent chromium subsequently occurs during the mixing of groundwater and river water, with relatively little change taking place in speciation

Seasonal variations in chromium concentration in urban atmospheric aerosol in the city of Radom

Directory of Open Access Journals (Sweden)

Molik Artur

2018-01-01

Full Text Available This paper presents seasonal variations in the occurrence of chromium in urban particulate matter (PM. Radom is an interesting area for this type of research due to its typical antiquated heating infrastructure. PM samples of two particulate fractions PM2.5 (particulates ≤ 2.5 µm and PM10 (particulates ≤ 10 µm were collected using a Copley cascade impactor Hi-Flow MOUDI Model 130. Chromium was determined in the samples using the GF-AAS technique. The concentration of chromium in PM2.5 was in the range of 0.38 to 3.2 ng/m3, whereas in PM10 it ranged from 0.43 to 4.1 ng/m3.

Radon in houses: how large is the risk?

International Nuclear Information System (INIS)

Darby, S.; Doll, R.

1990-01-01

Based on the revised estimates of the average annual effective dose equivalents received from natural radiation, it is suggested that radon in houses may be responsible for some of cases of lung cancer. Moreover radon and smoking interact more than additively but less than multiplicatively in the production of lung cancer. In conclusion it is postulated that current estimates of the size of the risk associated with exposures in houses of the order of 20 Bq m -3 or about 6 % of the current lifetime risk of the incidence of lung cancer in the United Kingdom may be too high or they may be too low by a factor of two. 35 refs., 6 tabs

Structure and magnetic properties of chromium doped cobalt molybdenum nitrides

Science.gov (United States)

Guskos, Niko; Żołnierkiewicz, Grzegorz; Typek, Janusz; Guskos, Aleksander; Adamski, Paweł; Moszyński, Dariusz

2016-09-01

Four nanocomposites containing mixed phases of Co3Mo3N and Co2Mo3N doped with chromium have been prepared. A linear fit is found for relation between Co2Mo3N and chromium concentrations. The magnetization in ZFC and FC modes at different temperatures (2-300 K) and in applied magnetic fields (up to 70 kOe) have been investigated. It has been detected that many magnetic characteristics of the studied four nanocomposites correlate not with the chromium concentration but with nanocrystallite sizes. The obtained results were interpreted in terms of magnetic core-shell model of a nanoparticle involving paramagnetic core with two magnetic sublattices and a ferromagnetic shell related to chromium doping.

Effect of radiation on hydrotalcites with chromates

International Nuclear Information System (INIS)

Martinez G, S.; Bulbulian, S.

2002-01-01

Nowadays the generation of radioactive wastes is matter of several studies. In this work anion material, chromates, in hydrotalcite are retained which are anion exchangers. It was proposed to heat the hydrotalcite until temperature of 1200 C with the purpose to form the (MgAl 2 O 4 ) spinel is very stable and in this way to immobilize strongly the anions. The effect of radiation on this compound and in particular the chromium lixiviation with solution 1N NaCl. It was found that in all case, the anions are strongly retained in the spinel formed. The radiation dose used for this was 100 Mrad, the samples were treated with NaCl 1N for studying the Cr lixiviation. The results show that for the calcined samples at 1200 C and irradiated there are not chromium escapes, which indicates that it is strongly retained in the spinel that is the formed structure after of the material calcination. (Author)

The determination of chromium-50 in human blood and its utilization for blood volume measurements

International Nuclear Information System (INIS)

Zeisler, R.; Young, I.

1986-01-01

Possible relationships between insufficient blood volume increases during pregnancy and infant mortality could be established with an adequate measurement procedure. An accurate and precise technique for blood volume measurements has been found in the isotope dilution technique using chromium-51 as a label for red blood cells. However, in a study involving pregnant women, only stable isotopes can be used for labeling. Stable chromium-50 can be determined in total blood samples before and after dilution experiments by neutron activation analysis (NAA) or mass spectrometry. However, both techniques may be affected by insufficient sensitivity and contamination problems at the inherently low natural chromium concentrations to be measured in the blood. NAA procedures involving irradiations with highly thermalized neutrons at a fluence rate of 2x10 13 n/cm 2 xs and low background gamma spectrometry are applied to the analysis of total blood. Natural levels of chromium-50 in human and animal blood have been found to be <0.1 ng/mL; i.e., total chromium levels of <3 ng/mL. Based on the NAA procedure, a new approach to the blood volume measurement via chromium-50 isotope dilution has been developed which utilizes the ratio of the induced activities of chromium-51 to the iron-59 in three blood samples taken from each individual, namely blank, labeled and diluted labeled blood. (author)

The influence of coordination geometry and valency on the K-edge absorption near edge spectra of selected chromium compounds

International Nuclear Information System (INIS)

Pantelouris, A.; Modrow, H.; Pantelouris, M.; Hormes, J.; Reinen, D.

2004-01-01

X-ray absorption spectra at the chromium K-edge are reported for a number of selected chromium compounds of known chemical structure. The spectra were obtained with use of synchrotron radiation available at the ELectron Stretcher Accelerator ELSA in Bonn. The compounds studied include the tetrahedrally coordinated compounds Ca 2 Ge 0.8 Cr 0.2 O 4 , Ba 2 Ge 0.1 Cr 0.9 O 4 , Sr 2 CrO 4 , Ca 2 (PO 4 ) x (CrO 4 ) 1-x Cl (x=0.25,0.5), Ca 5 (CrO 4 ) 3 Cl, CrO 3 , the octahedrally coordinated compounds Cr(II)-acetate, CrCl 3 , CrF 3 , Cr 2 O 3 , KCr(SO 4 ) 2 · 12H 2 O, CrO 2 and cubic coordinated metallic chromium. In these compounds chromium exhibits a wide range of formal oxidation states (0 to VI). The absorption features in the near edge region are shown to be characteristic of the spatial environment of the absorbing atom. The occurrence of a single pre-edge line easily allows one to distinguish between tetrahedral and octahedral coordination geometry, whereas the energy position of the absorption edge is found to be very sensitive to the valency of the excited chromium atom. Calculations of the ionisation potential of Cr in different oxidation states using the non-relativistic Hartree-Fock method (Froese-Fischer) confirm that the ionisation limit shifts to higher energy with increasing Cr valency. More detailed information on the electronic structure of the different compounds is gained by real-space full multiple scattering calculations using the FEFF8 code

The influence of coordination geometry and valency on the K-edge absorption near edge spectra of selected chromium compounds

Science.gov (United States)

Pantelouris, A.; Modrow, H.; Pantelouris, M.; Hormes, J.; Reinen, D.

2004-05-01

X-ray absorption spectra at the chromium K-edge are reported for a number of selected chromium compounds of known chemical structure. The spectra were obtained with use of synchrotron radiation available at the ELectron Stretcher Accelerator ELSA in Bonn. The compounds studied include the tetrahedrally coordinated compounds Ca 2Ge 0.8Cr 0.2O 4, Ba 2Ge 0.1Cr 0.9O 4, Sr 2CrO 4, Ca 2(PO 4) x(CrO 4) 1- xCl ( x=0.25,0.5), Ca 5(CrO 4) 3Cl, CrO 3, the octahedrally coordinated compounds Cr(II)-acetate, CrCl 3, CrF 3, Cr 2O 3, KCr(SO 4) 2 · 12H 2O, CrO 2 and cubic coordinated metallic chromium. In these compounds chromium exhibits a wide range of formal oxidation states (0 to VI). The absorption features in the near edge region are shown to be characteristic of the spatial environment of the absorbing atom. The occurrence of a single pre-edge line easily allows one to distinguish between tetrahedral and octahedral coordination geometry, whereas the energy position of the absorption edge is found to be very sensitive to the valency of the excited chromium atom. Calculations of the ionisation potential of Cr in different oxidation states using the non-relativistic Hartree-Fock method (Froese-Fischer) confirm that the ionisation limit shifts to higher energy with increasing Cr valency. More detailed information on the electronic structure of the different compounds is gained by real-space full multiple scattering calculations using the FEFF8 code.

Investigation of the surface composition of electrodeposited black chromium by X-ray photoelectron spectroscopy

International Nuclear Information System (INIS)

Survilienė, S.; Češūnienė, A.; Jasulaitienė, V.; Jurevičiūtė, I.

2015-01-01

Highlights: • Black chromium electrodeposited from a Cr(III) bath is composed of oxide, hydroxide and metallic chromium. • Metallic phase is absent in black chromium electrodeposited from a Cr(III) + ZnO bath. • The near-surface layer is rich in hydroxides, whereas oxides of both metals predominate in the depth of the coatings. - Abstract: The paper reviews black chromium electrodeposited from a trivalent chromium bath containing ZnO as a second main component. The chemical compositions of the top layers of the black chromium coatings were studied by the X-ray photoelectron spectroscopy method. The surface of black chromium was found to be almost entirely covered with organic substances. To gain information on the state of each element in the deposit bulk, the layer-by-layer etching of the black chromium surface with argon gas was used. Analysis of XPS spectra has shown that the top layers of black chromium without zinc are composed of various Cr(III) components, organic substances and metallic Cr, whereas metallic Cr is almost absent in black chromium containing some amount of Zn(II) compounds. The ratios of metal/oxide phases were found to be 10/27 and 2/28 for black chromium without and with zinc, respectively. It has been determined that owing to the presence of ZnO in the Cr(III) bath, the percentage of metallic chromium is substantially reduced in black chromium which is quite important for good solar selective characteristics of the coating. The results confirm some of earlier observations and provide new information on the composition of the near-surface layers

On-line preconcentration and determination of chromium in parenteral solutions by inductively coupled plasma optical emission spectrometry

International Nuclear Information System (INIS)

Gil, R.A.; Cerutti, S.; Gasquez, J.A.; Olsina, R.A.; Martinez, L.D.

2005-01-01

A method for the preconcentration and speciation of chromium was developed. On-line preconcentration and determination were obtained using inductively coupled plasma optical emission spectrometry (ICP-OES) coupled with flow injection. To determinate the chromium (III) present in parenteral solutions, chromium was retained on activated carbon at pH 5.0. On the other hand, a step of reduction was necessary in order to determine total chromium content. The Cr(VI) concentration was then determined by difference between the total chromium concentration and that of Cr(III). A sensitivity enrichment factor of 70-fold was obtained with respect to the chromium determination by ICP-OES without preconcentration. The detection limit for the preconcentration of 25 ml of sample was 29 ng l -1 . The precision for the 10 replicate determinations at the 5 μg l -1 Cr level was 2.3% relative standard deviation, calculated with the peak heights. The calibration graph using the preconcentration method for chromium species was linear with a correlation coefficient of 0.9995 at levels near the detection limits up to at least 60 μg l -1 . The method can be applied to the determination and speciation of chromium in parenteral solutions

Impurity effects on the magnetic ordering in chromium

International Nuclear Information System (INIS)

Fishman, R.S.

1992-05-01

It is well-known that impurities profoundly alter the magnetic properties of chromium. While vanadium impurities suppress the Neel temperature T N , manganese impurities enhanced T N substantially. As evidenced by neutron scattering experiments, doping with as little as 0.2% vanadium changes the transition from weakly first order to second order. Young and Sokoloff explained that the first-order transition in pure chromium is caused by a charge-density wave which is the second harmonic of the spin-density wave. By examining the subtle balance between the spin-density and charge- density wave terms in the mean-field free energy, we find that the first-order transition is destroyed when the vanadium concentration exceeds about 0.15%, in agreement with experiments

USE OF TWO DIGESTION METHODS IN THE EVALUATION OF CHROMIUM CONTENT IN CATTLE'S MEAT SUPPLEMENTED WITH CHROMIUM CHELATES

Directory of Open Access Journals (Sweden)

R. L. T. de Andrade

2015-06-01

Full Text Available The present study aimed to analyze the chromium content in beef using two digestion methods. There were used samples from 24 18-month-old male cattle, and twelve of them were supplemented and twelve were not supplemented with chromium chelate. These samples were evaluated by atomic absorption spectroscopy, previously submitted to digestion method using nitric acid (65% with hydrogen peroxide (35% and to digestion method, using solution of nitric perchloric acid in the proportion 3:1. Immediately after the slaughter, the carcasses were sent to sanitary maturation. After 24 hours, samples between 12th and 13th rib in the muscle Longissimus Thoracis were taken. For evaluation, it was used completely randomized design (Die and analysis of variance (ANOVA at 5% of significance level. The results didn't evidenced any significant difference (p>0,05 between the (cromo content, regardless the supplementation. The same happened with the digestion methods used.

Chromium in urothelial carcinoma of the bladder.

Science.gov (United States)

Golabek, Tomasz; Socha, Katarzyna; Kudelski, Jacek; Darewicz, Barbara; Markiewicz-Zukowska, Renata; Chlosta, Piotr; Borawska, Maria

2017-12-23

Many epidemiological and experimental studies report a strong role of chemical carcinogens in the etiology of bladder cancer. However, the involvement of heavy metals in tumourigenesis of urothelial carcinoma of the bladder has been poorly investigated. Therefore, the aim of this study was to examine the relationship between chromium (Cr) and bladder cancer. Chromium concentration in two 36-sample series of bladder cancer tissue and sera from patients with this neoplasm were matched with those of a control group. The amount of trace elements in every tissue sample was determined using atomic absorption spectrometry. This was correlated with tumour stage. While the median chromium concentration levels reached statistically higher values in the bladder cancer tissue, compared with the non-cancer tissue (99.632ng/g and 33.144ng/g, respectively; p<0.001), the median Cr levels in the sera of the patients with this carcinoma showed no statistical difference when compared to those of the control group (0.511μg/l and 0.710μg/l, respectively; p=0.408). The median levels of Cr in the bladder tissue, depending on the stage of the tumour, compared with the tissue without the neoplasm, observed the same relationship for both non-muscle invasive and muscle-invasive tumours (p<0.001 and p<0.01, respectively). This study shows that patients with urothelial carcinoma of the bladder had higher tissue Cr levels than people without tumour, while no difference was found in the Cr serum levels between the two groups of patients under investigation.

A Review of Heat Transfer in Terraced Houses of Tropical Climate

Directory of Open Access Journals (Sweden)

Azzmi Norazura Mizal

2014-01-01

Full Text Available Heat is the process of energy circulation and replacement of air from hot to cold. In tropical climates, more heat is received because of the location of Malaysia of the equatorial line. Excessive heat in buildings causes discomfort to the occupants in tropical climate. Tropical rainforest climate receives higher solar radiation and terrestrial radiation reaching the building envelopes contributes to this problem. The design of the building should be more concern on reducing this heat. This paper provides a review of heat contribution in a terraced house indoor environment for tropical climate. A good comfortable home is part of the sustainable development agenda to improve the quality of life. Terraced houses are the most living quarters in mass living scheme for urban areas. The incoming solar energy from the sun into the building surface cannot be changed, therefore a consideration of passive building design need to be applied in terraced house design. Data collection gathered from this literature survey will assist to identify problems of discomfort occupant. This strategy would assist in improving the building industry in promoting sustainable development in Malaysia.

76 FR 8773 - Superalloy Degassed Chromium From Japan

Science.gov (United States)

2011-02-15

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-1090 (Review)] Superalloy Degassed Chromium From Japan AGENCY: United States International Trade Commission. ACTION: Termination of five-year... revocation of the antidumping duty order on superalloy degassed chromium from Japan would be likely to lead...

Information profiles on potential occupational hazards: Inorganic chromium compounds. Draft report (Second)

Energy Technology Data Exchange (ETDEWEB)

1982-02-01

Information profiles are presented for the following inorganic chromium compounds: chromic(VI) acid, chromic(III) hydroxide, chromic(III) oxide, chromic(III) sulfate, chromic(III) sulfate (basic), chromium dioxide, potassium dichromate(VI), lead chromate, sodium-chromate(VI), sodium-dichromate(VI), and zinc-yellow-chromate(VI). Biological effects of hexavalent chromium in humans included skin ulceration, dermatitis, nasal membrane irritation and ulceration, nasal septal perforation, rhinitis, nosebleed, nephritis, liver damage, epigastric pain, pulmonary congestion and edema, and erosion and discoloration of teeth. Chromium(VI) compounds caused mutations in a variety of systems. Exposure to trivalent chromium in the work place has caused contact dermatitis and chrome ulcers. Epidemiological studies indicated respiratory carcinogenicity among workers occupationally exposed during chromate production.

Method for electrodeposition of nickel--chromium alloys and coating of uranium

International Nuclear Information System (INIS)

Stromatt, R.W.; Lundquist, J.R.

1975-01-01

High-quality electrodeposits of nickel-chromium binary alloys in which the percentage of chromium is controlled can be obtained by the addition of a complexing agent such as ethylenediaminetetraacetic disodium salt to the plating solution. The nickel-chromium alloys were found to provide an excellent hydrogen barrier for the protection of uranium fuel elements. (U.S.)

Analysis of molybdenum, chromium, vanadium and iron by polarographic techniques

International Nuclear Information System (INIS)

Al-Zand, T.K.

1986-01-01

The application of direct current Tast polarograph, differential pulse polarography and phase-selective alternative current Tast polarography to the problem of determining molybdenum, chromium, vanadium and iron in various supporting electrolytes is reported. The effect of the supporting electrolyte on the wave/peak potential and sensitivity of the metal ion have been examined. The polarographic methods were applied for simultaneous determination of chromium (3)/chromium (6), vanadium (4), vanadium (5) and iron (2)/iron (3) in different supporting electrolytes

Association between maternal urinary chromium and premature rupture of membranes in the Healthy Baby Cohort study in China.

Science.gov (United States)

Huang, Sha; Xia, Wei; Li, Yuanyuan; Zhang, Bin; Zhou, Aifen; Zheng, Tongzhang; Qian, Zhengmin; Huang, Zheng; Lu, Shi; Chen, Zhong; Wang, Youjie; Pan, Xinyun; Huo, Wenqian; Jin, Shuna; Jiang, Yangqian; Xu, Shunqing

2017-11-01

Chromium exposure from increasing industrial releases has become a threat for pregnant women due to the potential health effects on vulnerable embryos. Previous studies have suggested that maternal chromium exposure is associated with adverse birth outcomes, but no epidemiological research has been conducted to examine the relationship between chromium exposure and premature rupture of membranes (PROM). This study aimed at investigating the association of maternal urinary chromium exposure levels with PROM and was performed with 5408 pregnant women recruited from 2012 to 2014 in the city of Wuhan, China. Maternal urinary chromium collected before labor was adjusted with creatinine, and its association with PROM was evaluated using logistic regression. Each one unit increase in the natural logarithm transformed maternal urinary chromium concentration (μg/g creatinine), an odds ratio (OR) of 1.47 [95% confidence interval (CI): 1.36, 1.58] for PROM was observed. Compared to the lowest tertile of maternal urinary chromium, PROM was positively correlated with increased urinary levels of chromium (adjusted OR = 1.42; 95% CI: 1.09, 1.84 for the medium tertile; adjusted OR = 2.77; 95% CI: 2.18, 3.52 for the highest tertile). Additionally, the association of chromium with PROM appeared to be more significant among male infants (adjusted OR = 3.52; 95% CI: 2.51, 4.94 for the highest tertile) than female infants (adjusted OR = 2.16; 95% CI: 1.52, 3.06 for the highest tertile) (p for interaction = 0.05). Our large birth cohort showed an association between maternal urinary chromium levels and PROM, and the association may differ by infant gender. Further studies from different populations are needed to confirm the observed association. Copyright © 2017 Elsevier Ltd. All rights reserved.

Review article. Adverse hematological effects of hexavalent chromium: an overview

Directory of Open Access Journals (Sweden)

Ray Rina Rani

2016-06-01

Full Text Available Workers of tanneries, welding industries, factories manufacturing chromate containing paints are exposed to hexavalent chromium that increas¬es the risk of developing serious adverse health effects. This review elucidates the mode of action of hexavalent chromium on blood and its adverse effects. Both leukocyte and erythrocyte counts of blood sharply decreased in Swiss mice after two weeks of intraperitoneal treatment with Cr (VI, with the erythrocytes transforming into echinocytes. The hexavalent chromium in the blood is readily reduced to trivalent form and the reductive capacity of erythrocytes is much greater than that of plasma. Excess Cr (VI, not reduced in plasma, may enter erythrocytes and lymphocytes and in rodents it induces microcytic anemia. The toxic effects of chromium (VI include mitochondrial injury and DNA damage of blood cells that leads to carcinogenicity. Excess Cr (VI increases cytosolic Ca2+ activity and ATP depletion thereby inducing eryptosis. Se, vitamin C, and quercetin are assumed to have some protective effect against hexavalent chromium induced hematological disorders.

Alpha-emitting isotopes and chromium in a coastal California aquifer

International Nuclear Information System (INIS)

Densmore, Jill N.; Izbicki, John A.; Murtaugh, Joseph M.; Swarzenski, Peter W.; Bullen, Thomas D.