WorldWideScience

Sample records for implanting fused quartz

  1. Laser welding of fused quartz

    Science.gov (United States)

    Piltch, Martin S.; Carpenter, Robert W.; Archer, III, McIlwaine

    2003-06-10

    Refractory materials, such as fused quartz plates and rods are welded using a heat source, such as a high power continuous wave carbon dioxide laser. The radiation is optimized through a process of varying the power, the focus, and the feed rates of the laser such that full penetration welds may be accomplished. The process of optimization varies the characteristic wavelengths of the laser until the radiation is almost completely absorbed by the refractory material, thereby leading to a very rapid heating of the material to the melting point. This optimization naturally occurs when a carbon dioxide laser is used to weld quartz. As such this method of quartz welding creates a minimum sized heat-affected zone. Furthermore, the welding apparatus and process requires a ventilation system to carry away the silicon oxides that are produced during the welding process to avoid the deposition of the silicon oxides on the surface of the quartz plates or the contamination of the welds with the silicon oxides.

  2. Bonding energy of Sylgard on fused quartz: an experimental investigation

    Science.gov (United States)

    Liu, C.; Yeager, J. D.; Ramos, K. J.

    2015-02-01

    The bonding energy between the polymer Sylgard and fused quartz is determined experimentally using a miniature bulge test combined with three-dimensional digital image correlation (3D-DIC). Based on the experimental observation, Mindlin plate theory is used to compute the bonding energy (adhesive energy or surface energy) between the Sylgard and the fused quartz. The experimental results demonstrate that the combination of the miniature bulge test and the 3D-DIC provides a viable tool to directly measure interfacial and bonding properties.

  3. Quartz/fused silica chip carriers

    Science.gov (United States)

    1992-01-01

    The primary objective of this research and development effort was to develop monolithic microwave integrated circuit (MMIC) packaging which will operate efficiently at millimeter-wave frequencies. The packages incorporated fused silica as the substrate material which was selected due to its favorable electrical properties and potential performance improvement over more conventional materials for Ka-band operation. The first step towards meeting this objective is to develop a package that meets standard mechanical and thermal requirements using fused silica and to be compatible with semiconductor devices operating up to at least 44 GHz. The second step is to modify the package design and add multilayer and multicavity capacity to allow for application specific integrated circuits (ASIC's) to control multiple phase shifters. The final step is to adapt the package design to a phased array module with integral radiating elements. The first task was a continuation of the SBIR Phase 1 work. Phase 1 identified fused silica as a viable substrate material by demonstrating various plating, machining, and adhesion properties. In Phase 2 Task 1, a package was designed and fabricated to validate these findings. Task 2 was to take the next step in packaging and fabricate a multilayer, multichip module (MCM). This package is the predecessor to the phased array module and demonstrates the ability to via fill, circuit print, laminate, and to form vertical interconnects. The final task was to build a phased array module. The radiating elements were to be incorporated into the package instead of connecting to it with wire or ribbon bonds.

  4. Aqueous Wetting Films on Fused Quartz.

    Science.gov (United States)

    Mazzoco; Wayner

    1999-06-15

    Using an image analyzing interferometer, IAI, the interfacial characteristics of an isothermal constrained vapor bubble, CVB, in a quartz cuvette were studied as a precursor to heat transfer research. The effects of pH and electrolyte concentration on the meniscus properties (curvature and adsorbed film thickness) and the stability of the aqueous wetting films were evaluated. The surface potential in the electric double layer was a function of the cleaning and hydroxylation of the quartz surface. The disjoining pressure isotherm for pure water was very close to that predicted by the Langmuir equation. For aqueous solutions of moderate electrolyte concentration, the Gouy-Chapman theory provided a good representation of the electrostatic effects in the film. The effect of temperature on the film properties of aqueous solutions and pure water was also evaluated: The meniscus curvature decreased with increasing temperature, while Marangoni effects, intermolecular forces, and local evaporation and condensation enhanced waves on the adsorbed film layer. Pure water wetting films were mechanically metastable, breaking into droplets and very thin films (less than 10 nm) after a few hours. Aqueous wetting films with pH 12.4 proved to be stable during a test of several months, even when subjected to temperature and mechanical perturbations. The mechanical stability of wetting films can explain the reported differences between the critical heat fluxes of pure water and aqueous solutions. The IAI-CVB technique is a simple and versatile experimental technique for studying the characteristics of interfacial systems. Copyright 1999 Academic Press.

  5. Arsenic Sulfide Nanowire Formation on Fused Quartz Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Olmstead, J.; Riley, B.J.; Johnson, B.R.; Sundaram, S.K.

    2005-01-01

    Arsenic sulfide (AsxSy) nanowires were synthesized by an evaporation-condensation process in evacuated fused quartz ampoules. During the deposition process, a thin, colored film of AsxSy was deposited along the upper, cooler portion of the ampoule. The ampoule was sectioned and the deposited film analyzed using scanning electron microscopy (SEM) to characterize and semi-quantitatively evaluate the microstructural features of the deposited film. A variety of microstructures were observed that ranged from a continuous thin film (warmer portion of the ampoule), to isolated micron- and nano-scale droplets (in the intermediate portion), as well as nanowires (colder portion of the ampoule). Experiments were conducted to evaluate the effects of ampoule cleaning methods (e.g. modify surface chemistry) and quantity of source material on nanowire formation. The evolution of these microstructures in the thin film was determined to be a function of initial pressure, substrate temperature, substrate surface treatment, and initial volume of As2S3 glass. In a set of two experiments where the initial pressure, substrate thermal gradient, and surface treatment were the same, the initial quantity of As2S3 glass per internal ampoule volume was doubled from one test to the other. The results showed that AsxSy nanowires were only formed in the test with the greater initial quantity of As2S3 per internal ampoule volume. The growth data for variation in diameter (e.g. nanowire or droplet) as a function of substrate temperature was fit to an exponential trendline with the form y = Aekx, where y is the structure diameter, A = 1.25×10-3, k = 3.96×10-2, and x is the temperature with correlation coefficient, R2 = 0.979, indicating a thermally-activated process.

  6. Determining the nonlinear refractive index of fused quartz by femtosecond laser Z-scan technology

    Science.gov (United States)

    Zhang, Lin; Ren, Huan; Ma, Hua; Shi, Zhendong; Yang, Yi; Yuan, Quan; Feng, Xiaoxuan; Ma, Yurong; Chen, Bo

    2016-10-01

    Z-scan technology is an experimental technique for determining the nonlinear refractive index based on the principle of transformation of phase distortion to amplitude distortion when a laser beam propagates through a nonlinear material. For most of the Z-scan system based on the nanosecond or picosecond laser, the accumulation of thermal effects becomes a big problem in nonlinear refractive index measurement especially for the nonlinear materials such as fused quartz and neodymium glass which have a weak nonlinear refractive effect. To overcome this problem, a system for determining the nonlinear refractive index of optical materials based on the femtosecond laser Z-scan technology is presented. Using this system, the nonlinear refractive index of the fused quartz is investigated.

  7. On the mechanical quality factors of cryogenic test masses from fused silica and crystalline quartz

    CERN Document Server

    Schroeter, Anja; Schnabel, Roman; Reid, Stuart; Martin, Iain; Rowan, Sheila; Schwarz, Christian; Koettig, Torsten; Neubert, Ralf; Thürk, Matthias; Vodel, Wolfgang; Tünnermann, Andreas; Danzmann, Karsten; Seidel, Paul

    2007-01-01

    Current interferometric gravitational wave detectors (IGWDs) are operated at room temperature with test masses made from fused silica. Fused silica shows very low absorption at the laser wavelength of 1064 nm. It is also well suited to realize low thermal noise floors in the detector signal band since it offers low mechanical loss, i. e. high quality factors (Q factors) at room temperature. However, for a further reduction of thermal noise, cooling the test masses to cryogenic temperatures may prove an interesting technique. Here we compare the results of Q factor measurements at cryogenic temperatures of acoustic eigenmodes of test masses from fused silica and its crystalline counterpart. Our results show that the mechanical loss of fused silica increases with lower temperature and reaches a maximum at 30 K for frequencies of slightly above 10 kHz. The losses of crystalline quartz generally show lower values and even fall below the room temperature values of fused silica below 10 K. Our results show that in ...

  8. Pressure derivatives of elastic moduli of fused quartz to 10 kb

    Science.gov (United States)

    Peselnick, L.; Meister, R.; Wilson, W.H.

    1967-01-01

    Measurements of the longitudinal and shear moduli were made on fused quartz to 10 kb at 24??5??C. The anomalous behavior of the bulk modulus K at low pressure, ???K ???P 0, at higher pressures. The pressure derivative of the rigidity modulus ???G ???P remains constant and negative for the pressure range covered. A 15-kb hydrostatic pressure vessel is described for use with ultrasonic pulse instrumentation for precise measurements of elastic moduli and density changes with pressure. The placing of the transducer outside the pressure medium, and the use of C-ring pressure seals result in ease of operation and simplicity of design. ?? 1967.

  9. One GHz leaky SAW velocity of metal layers and bilayers evaporated onto fused quartz

    Science.gov (United States)

    Walikainen, Dale

    1992-01-01

    An acoustic microscope operating at 1 GHz was used to determine the surface acoustic wave velocities v of thin film metal layers and metal bilayers deposited onto fused quartz. V(0)'s influence was reduced by gating. This produced a calibrated accuracy of 3 percent. A program was constructed from the explicitly solved 6 x 6 theoretical determinant. Single film thicknesses were decided upon by using this theory to produce a v equal to a standard. Since the single film v's were linear with respect to their thickness, half the single film thicknesses were used for the bilayered films. The velocities for these bilayered films agreed with theory. This experimentally confirms the theoretical technique used here to examine bilayered systems, or a prototype composite interphase. No discrepancy was seen for gold films as others have reported. V(z) seemed insensitive to the formation of intermetallics or CuO. Some annealed and unannealed platinum films did not change the v from that of fused quartz. Two platinum films whose v's were in agreement with theory peeled off with the tape test.

  10. Mechanism of Material Removal in Nanomachining of Fused Quartz using AFM Diamond Tip

    Science.gov (United States)

    Ichida, Yoshio; Yamaguchi, Takashi; Sasanuma, Makoto

    Nanometer-scale machining experiments on fused quartz surfaces have been performed using an atomic force microscope combined with a two-axis capacitive force/displacement transducer. The minimum normal force fnP required to reproducibly form a groove was about 4.7 µN. The minimum critical normal force fnR, tangential force ftR and groove depth dgR when the material removal process began were found to be 33.7 µN, 18.7 µN, and 4.3 nm, respectively. Changes in the swelling ratio Rs and the ratio of force components at the critical normal force fnR can be used to detect a critical condition when the material deformation behavior changes from plastic deformation to material removal.

  11. Dependence of growth rate of quartz in fused silica on pressure and impurity content

    Science.gov (United States)

    Fratello, V. J.; Hays, J. F.; Turnbull, D.

    1980-01-01

    The effects of pressure, temperature, and some variations in impurity content on the growth rate u of quartz into fused silica were measured. Under all conditions the growth rate was interface controlled and increased exponentially with pressure with an activation volume averaging -21.2 cu cm/mole. The activation enthalpy for all specimens is extrapolated to a zero pressure value of 64 kcal/mole, within the experimental uncertainty. At a given stoichiometry the effect of hydroxyl content on growth rate is described entirely by a linear term C(OH) in the prefactor of the equation for the growth rate. The effect of chlorine impurity can be described similarly. Also u is increased as the ideal stoichiometry is approached from the partially reduced state.

  12. The compaction of fused silica resulting from ion implantation

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, C.M.; Ridgway, M.C. [Australian National Univ., Canberra, ACT (Australia); Leech, P.L. [Telstra Research Laboratories, Clayton, Victoria (Australia)

    1996-12-31

    Ion implantation of fused silica results in compaction and consequently an increase in refractive index. This method of modifying the near-surface region has been shown as a potential means for fabricating single mode channel waveguides. This study has measured the compaction of the implanted regions for Si implantations as a function of dose (2x10{sup 12} - 6x10{sup l6} ions/cm{sup 2}), energy (1-9 MeV) and post-implantation annealing temperature (200-900 degree C). For a given energy, a dose-dependence of the step height (depth of compacted region) is observed for doses less than {approx}10{sup 15} ions/cm{sup 2}. At higher doses the step height saturates. For a given dose, a linear trend is evident for the step height as a function of energy suggesting that the major mechanism for this compaction is electronic stopping. As the annealing temperature increases, the step height gradually decreases from {approx}0.1-0.2 {mu} to -10-20% of the original value. From the annealing data, it is possible to extract an activation energy of 0.08 eV associated with the thermal removal of the compacted region. 4 refs., 4 figs.

  13. Electron spin resonance and thermoluminescence in powder form of clear fused quartz: effects of grinding

    CERN Document Server

    Ranjbar, A H; Randle, K

    1999-01-01

    Clear fused quartz (CFQ) tubes were powdered either manually by using a mortar and pestle (for coarse production) or mechanically, using a micronising mill (for fine production). A high and multisignal electron spin resonance (ESR) background was found in the fine powder even after annealing it at 900 deg. C for 20 min. In the case of the coarse powder, the signal (ESR background) varied inversely with particle size and was quite high for particle sizes lower than 38 mu m. In a subsidiary experiment, using fine SiO sub 2 powder (99.8% pure, with the particle size of approx 0.007 mu m), manufactured by using flame hydrolysis, only a weak background signal was found. The sup 6 sup 0 Co gamma-ray irradiated powders (approx 22 Gy) were subjected to ESR analysis or thermoluminescence (TL) readout. The ESR intensity of the coarse powder varied directly with particle size. Thus, the intensity for a particle size of 20-38 mu m was very low and almost the same as the unirradiated intensity. In TL readout the results w...

  14. Effect of the fused quartz particle density on nucleation and grain control of high-performance multicrystalline silicon ingots

    Science.gov (United States)

    Ding, Junjing; Yu, Yunyang; Chen, Wenliang; Zhou, Xucheng; Wu, Zhiyong; Zhong, Genxiang; Huang, Xinming

    2016-11-01

    The nucleation process of high-performance multicrystalline silicon (HP mc-Si) growth seeded by fused quartz particles (FQP) through directional solidification is crucial for the ingot quality. To determine the optimal density of FQP and obtain a better nucleation process and the grain growth, we cast ingots using four different densities of FQP fixed on the bottom of the four quartz crucibles and covered them with a certain thickness of Si3N4 coating. FQP sizes of 30-50 mesh were used, and the influence of the fused quartz particle density on the nucleation mechanism, initial grain uniformity, grain size, density of dislocation clusters, and cell efficiency were analyzed. Compared with the ingots seeded with other three densities of FQP, the 220 particles/cm2 of FQP seeded ingot showed better uniformity of nucleation and initial grains. A large number of small uniform Si grains with lower density of dislocation clusters in the bottom of the ingot were observed. The average conversion efficiency of p-type solar cells manufactured with the 220 particles/cm2 seeded ingot (18.28%) was 0.19% higher than that manufactured with the 120 particles/cm2 seeded ingot (18.09%).

  15. Compression testing spherical particles for strength: Theory of the meridian crack test and implementation for microscopic fused quartz

    Science.gov (United States)

    Pejchal, Václav; Žagar, Goran; Charvet, Raphaël; Dénéréaz, Cyril; Mortensen, Andreas

    2017-02-01

    We show that uniaxial compression testing of spherical particles can give unambiguous access to their tensile strength as governed by surface flaws if one uses pairs of elasto-plastic platens, tailoring their hardness in order to control the relative area of particle-to-platen contact during the test. This eliminates the development of contact microcracks that are typically found to govern particle fracture when hard platens are used. We show that, if the platen materials are well chosen, one can probe a range of stress states for which it is known that particle failure was initiated along the surface, under elevated hoop stress within a region situated remote from the points of load application. Specifically, platens must be chosen such that particles tend to fracture when the ratio of projected contact area radius to particle radius exceeds a specific value that depends on the Poisson ratio of the particles. With fused quartz of Poisson ratio 0.17, this specific ratio value equals 0.65. We demonstrate the approach using microscopic fused quartz spheres 40±20 μm in diameter as a testbench material; with those particles hardened steel serves as an appropriate platen material. Their strength values are statistically distributed; this is addressed using several platen materials. The resulting bank of data is interpreted using established survival-analysis methods, namely the non-parametric product-limit estimator. We also give a maximum likelihood estimation of the particle strength Weibull distribution parameters derived from the ensemble of data after left-truncation and/or right-censoring of data points situated inside of the range of unambiguous surface fracture strength measurement for each platen material. This gives a Weibull modulus of 6.3 and characteristic strength of 890 MPa for the fused quartz particles. These values are significantly lower than what is produced in high-strength fused quartz fibers of comparable diameter; the difference is most likely

  16. Thermal expansion of a fused quartz tube in a dimensional stability test facility.

    Science.gov (United States)

    Wolff, E G; Eselun, S A

    1979-04-01

    A facility to monitor the dimensional stability of structures of arbitrary size or shape under varying temperature and pressure conditions is described. Real-time linear displacements are measured with a modified Michelson laser interferometer to a resolution of less than one part in 10(7) and an accuracy of approximately 2 parts in 10(7) for approximately 1 m gauge lengths. Verification of the system accuracy with a quartz tube required considerations of its fabrication and compositional characteristics.

  17. Implant survivorship analysis after minimally invasive sacroiliac joint fusion using the iFuse Implant System®

    Directory of Open Access Journals (Sweden)

    Cher DJ

    2015-11-01

    Full Text Available Daniel J Cher,1 W Carlton Reckling,2 Robyn A Capobianco1 1Department of Clinical Affairs, SI-BONE, Inc., 2Department of Medical Affairs, SI-BONE, Inc., San Jose, CA, USA Introduction: Surgical revision rate is a key outcome with all permanent implants. The iFuse Implant System® is a permanent implant used to perform minimally invasive sacroiliac joint fusion. The purpose of this study is to determine the surgical revision rate after sacroiliac joint fusion surgery with this system. Methods: Using two internal sources of information, revision surgeries were identified and linked to index surgeries. The likelihood of revision surgery was calculated using the Kaplan–Meier life table approach. Predictors of revision were explored. Results: Four-year survivorship free from implant revision was 96.46%. Revision rate did not differ by sex and was lower for age >65. In all, 24% of revisions occurred within the first 30 days after surgery; 63.5% occurred within year 1. Implant survivorship has improved annually since the device was introduced in 2009. Conclusion: The survivorship rate with this implant is high and improving; the rate is somewhat higher than total hip replacement but lower than that of lumbar spine procedures. Keywords: safety, sacroiliac joint fusion, iFuse Implant System, revision

  18. Room temperature analysis of dielectric function of ZnO-based thin film on fused quartz substrate

    Science.gov (United States)

    Kurniawan, Robi; Sutjahja, Inge M.; Winata, Toto; Rusydi, Andrivo; Darma, Yudi

    2015-09-01

    A set of sample consist of pure ZnO and Cu-doped ZnO film were grown on fused-quartz substrates using pulsed laser deposition (PLD) technique. Here, we report room temperature spectroscopic ellipsometry analysis (covering energy range of 0.5 to 6.3 eV) of pure ZnO film and Cu doped ZnO film at 8 in at. %. The thickness of pure ZnO and Cu-doped ZnO film using in this study is about 350 nm. To extract the dielectric function of ZnO thin film, multilayer modeling is performed which takes into account reflections at each interface through Fresnel coefficients. This method based on Drude-Lorentz models that connect with Kramers-Kronig relations. The best fitting of Ψ (amplitude ratio) and Δ (phase difference) taken by SE measurement are obtained reasonably well by mean the universal fitting of three different photon incident angles. The imaginary part of dielectric function (ɛ2) show the broad peak at around 3.3 eV assigned as combination of optical band energy edge with excitonic states. The exitonic states could not be observed clearly in this stage. The evolution of extracted dielectric function is observable by introducing 8% Cu as indicated by decreasing of excitonic intensity. This result indicates the screening of excitonic state. This study will bring us to have a good undestanding for the role of Cu impurities for ZnO thin films.

  19. Crown color match of implant-supported zirconia and Porcelain-Fused-to-Metal restorations:

    DEFF Research Database (Denmark)

    Peng, Min; Fei, Wei; Hosseini, Mandana

    2014-01-01

    Objectives: The aim of the present study was to compare the crown color match of implant supported zirconia restorations and Porcelain-Fused-to-Metal (PFM) restorations in anterior maxillary region by spectrophotometric evaluation. Materials and Methods: Eighteen patients with 29 implant......-supported single crowns in anterior maxillary area were recruited, 11 of the implant crowns were zirconia restorations and 18 were PFM restorations. Color match of the implant crown with contra-lateral/neighboring tooth at the position of body 1/3 of the crown were assessed using spectrophotometer (Spectro......ShadeTM, Micro Dental) in CIEL¿a¿b¿ coordinates. Subjective crown color match scores were evaluated. Independent sample t test of SPSS17.0 was used to compare the difference between zirconia restoration and PFM restoration. Spearman correlation was used to analyze the relationship between the spectrophotometric...

  20. Crown color match of implant-supported zirconia and Porcelain-Fused-to-Metal restorations:

    DEFF Research Database (Denmark)

    Peng, Min; Fei, Wei; Hosseini, Mandana

    2014-01-01

    Objectives: The aim of the present study was to compare the crown color match of implant supported zirconia restorations and Porcelain-Fused-to-Metal (PFM) restorations in anterior maxillary region by spectrophotometric evaluation. Materials and Methods: Eighteen patients with 29 implant......-supported single crowns in anterior maxillary area were recruited, 11 of the implant crowns were zirconia restorations and 18 were PFM restorations. Color match of the implant crown with contra-lateral/neighboring tooth at the position of body 1/3 of the crown were assessed using spectrophotometer (Spectro......ShadeTM, Micro Dental) in CIEL¿a¿b¿ coordinates. Subjective crown color match scores were evaluated. Independent sample t test of SPSS17.0 was used to compare the difference between zirconia restoration and PFM restoration. Spearman correlation was used to analyze the relationship between the spectrophotometric...

  1. Room temperature analysis of dielectric function of ZnO-based thin film on fused quartz substrate

    Energy Technology Data Exchange (ETDEWEB)

    Kurniawan, Robi; Sutjahja, Inge M.; Winata, Toto [Department of Physics, Institut Teknologi Bandung, Ganesa 10 Bandung 40132 (Indonesia); Rusydi, Andrivo; Darma, Yudi, E-mail: yudi@fi.itb.ac.id [Department of Physics, Institut Teknologi Bandung, Ganesa 10 Bandung 40132 (Indonesia); Singapore Synchrotron Light Source, National University of Singapore, 5 Research Link, Singapore 117603 (Singapore); NUSNNI-Nanocore, Department of Physics, National University of Singapore, 2 Science Drive 3, Singapore 117542 (Singapore)

    2015-09-30

    A set of sample consist of pure ZnO and Cu-doped ZnO film were grown on fused-quartz substrates using pulsed laser deposition (PLD) technique. Here, we report room temperature spectroscopic ellipsometry analysis (covering energy range of 0.5 to 6.3 eV) of pure ZnO film and Cu doped ZnO film at 8 in at. %. The thickness of pure ZnO and Cu-doped ZnO film using in this study is about 350 nm. To extract the dielectric function of ZnO thin film, multilayer modeling is performed which takes into account reflections at each interface through Fresnel coefficients. This method based on Drude-Lorentz models that connect with Kramers-Kronig relations. The best fitting of Ψ (amplitude ratio) and Δ (phase difference) taken by SE measurement are obtained reasonably well by mean the universal fitting of three different photon incident angles. The imaginary part of dielectric function (ε{sub 2}) show the broad peak at around 3.3 eV assigned as combination of optical band energy edge with excitonic states. The exitonic states could not be observed clearly in this stage. The evolution of extracted dielectric function is observable by introducing 8% Cu as indicated by decreasing of excitonic intensity. This result indicates the screening of excitonic state. This study will bring us to have a good undestanding for the role of Cu impurities for ZnO thin films.

  2. Ion implantation effect on surface properties of quartz. [Ar/sup +/, Ne/sup +/, C/sup +/, N/sup +/ implantation

    Energy Technology Data Exchange (ETDEWEB)

    Shitova, Eh.V.; Genkina, N.A.; Zotova, T.M.; Nikolaeva, L.E.; Chigrinskij, Yu.I.; Treskin, S.A.

    Results of studying the effects of implantation of various ions on the surface structure and microhardness of amorphous quartz are presented. Implantation of Ar/sup +/, Ne/sup +/, C/sup +/, N/sup +/ ions is shown to result in the microhardness increase by a factor of 1.5-2. The subsequent annealing of the ion-implanted specimens increases the microhardness 1.5-2 times as much.

  3. Preparation and Sintering Effect in Quartz-Barium Titanate Porous Ceramics and Permeability Modulation Using an Implanted Electrode

    Directory of Open Access Journals (Sweden)

    Ernesto Suaste Gómez

    2014-01-01

    Full Text Available Barium titanate and quartz mixed in different proportions were used to create porous piezoelectric ceramics. Three different sintering temperatures were used for the ceramics preparation; a nichrome wire was used as internal electrode in porous ceramics. Characteristics as porous area, porosity, and its relationship with quartz percentage and sintering temperatures were studied. Porous ceramics with an implanted electrode were created, by applying an alternating voltage in the internal electrode that controlled the liquid permeability coefficient, calculated by the Darcy Law.

  4. 3D Printing of Biocompatible Acellular Auricular Implant Using Dual Scaled Hydrid Technology Combining Fused Deposition Modeling with Electrospinning

    OpenAIRE

    Rezenda, R; Sabado, M; Kasjanovs, V; Baptista, L.; da Silva, K; Noritomi, P; Sena, F.; Wen, X.; Da Silva, J; Mironov, V.

    2013-01-01

    The dual-scaled hydrid scaffold fabrication technology based on combination of 3D printing (fused deposition modeling) and electrospining have been recently introduced. We report here the design, fabrication, mechanical testing, in vitro and in vivo biocompatibility testing of novel auricular implants for treatment microtia fabricated by dual scaled hydbrid scaffold fabrication technology.

  5. Thermal modeling of the NASA-Ames Research Center Cryogenic Optical Test Facility and a single-arch, fused-natural-quartz mirror

    Science.gov (United States)

    Ng, Y. S.; Augason, Gordon C.; Young, Jeffrey A.; Howard, Steven D.; Melugin, Ramsey K.

    1990-01-01

    A thermal model of the dewar and optical system of the Cryogenic Optical Test Facility at NASA-Ames Research Center was developed using the computer codes SINDA and MONTE CARLO. The model was based on the geometry, boundary conditions, and physical properties of the test facility and was developed to investigate heat transfer mechanisms and temperatures in the facility and in test mirrors during cryogenic optical tests. A single-arch, fused-natural-quartz mirror was the first mirror whose thermal loads and temperature distributions were modeled. From the temperature distribution, the thermal gradients in the mirror were obtained. The model predicted that a small gradient should exist for the single arch mirror. This was later verified by the measurement of mirror temperatures. The temperatures, predicted by the model at various locations within the dewar, were in relatively good agreement with the measured temperatures. The model is applicable to both steady-state and transient cooldown operations.

  6. Thermal modeling of the NASA-Ames Research Center Cryogenic Optical Test Facility and a single-arch, fused-natural-quartz mirror

    Science.gov (United States)

    Ng, Y. S.; Augason, Gordon C.; Young, Jeffrey A.; Howard, Steven D.; Melugin, Ramsey K.

    1990-11-01

    A thermal model of the dewar and optical system of the Cryogenic Optical Test Facility at NASA-Ames Research Center was developed using the computer codes SINDA and MONTE CARLO. The model was based on the geometry, boundary conditions, and physical properties of the test facility and was developed to investigate heat transfer mechanisms and temperatures in the facility and in test mirrors during cryogenic optical tests. A single-arch, fused-natural-quartz mirror was the first mirror whose thermal loads and temperature distributions were modeled. From the temperature distribution, the thermal gradients in the mirror were obtained. The model predicted that a small gradient should exist for the single arch mirror. This was later verified by the measurement of mirror temperatures. The temperatures, predicted by the model at various locations within the dewar, were in relatively good agreement with the measured temperatures. The model is applicable to both steady-state and transient cooldown operations.

  7. Fracture and Fatigue Resistance of Cemented versus Fused CAD-on Veneers over Customized Zirconia Implant Abutments.

    Science.gov (United States)

    Nossair, Shereen Ahmed; Aboushelib, Moustafa N; Morsi, Tarek Salah

    2015-01-05

    To evaluate the fracture mechanics of cemented versus fused CAD-on veneers on customized zirconia implant abutments. Forty-five identical customized CAD/CAM zirconia implant abutments (0.5 mm thick) were prepared and seated on short titanium implant abutments (Ti base). A second scan was made to fabricate 45 CAD-on veneers (IPS Empress CAD, A2). Fifteen CAD-on veneers were cemented on the zirconia abutments (Panavia F2.0). Another 15 were fused to the zirconia abutments using low-fusing glass, while manually layered veneers served as control (n = 15). The restorations were subjected to artificial aging (3.2 million cycles between 5 and 10 kg in a water bath at 37°C) before being axially loaded to failure. Fractured specimens were examined using scanning electron microscopy to detect fracture origin, location, and size of critical crack. Stress at failure was calculated using fractography principles (alpha = 0.05). Cemented CAD-on restorations demonstrated significantly higher (F = 72, p CAD-on and manually layered restorations. Fractographic analysis of fractured specimens indicated that cemented CAD-on veneers failed due to radial cracks originating from the veneer/resin interface. Branching of the critical crack was observed in the bulk of the veneer. Fused CAD-on veneers demonstrated cohesive fracture originating at the thickest part of the veneer ceramic, while manually layered veneers failed due to interfacial fracture at the zirconia/veneer interface. Within the limitations of this study, cemented CAD-on veneers on customized zirconia implant abutments demonstrated higher fracture than fused and manually layered veneers. © 2014 by the American College of Prosthodontists.

  8. Optical characterization of {beta}-FeSi{sub 2} thin films prepared on fused quartz by femtosecond laser

    Energy Technology Data Exchange (ETDEWEB)

    Zhou Youhua [Wuhan National Laboratory for Optoelectronics and School of Optoelectronics Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); School of Physics and Information Engineering, Jianghan University, Wuhan 430056 (China); Lu Peixiang [Wuhan National Laboratory for Optoelectronics and School of Optoelectronics Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China)]. E-mail: lupeixiang@mail.hust.edu.cn; Yang Guang [Wuhan National Laboratory for Optoelectronics and School of Optoelectronics Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Long Hua [Wuhan National Laboratory for Optoelectronics and School of Optoelectronics Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Zheng Qiguang [Wuhan National Laboratory for Optoelectronics and School of Optoelectronics Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2007-10-01

    Single-phase {beta}-FeSi{sub 2} thin films have been grown on quartz substrates using femtosecond laser deposition (800 nm, 50 fs, 1 kHz) under gas pressure of 3.0x10{sup -4} Pa. X-ray diffraction (XRD) and field-emission scanning electron microscopy (SEM) were used to determine the structural properties and surface images of the films. Typical XRD patterns of the film showed that no other diffraction peak except {beta}-FeSi{sub 2} was found. The SEM results indicated that the films were composed of well-distributed grains, in the range 50-150 nm in diameter. In addition, normal incidence spectral transmittance and reflectance data suggested that the {beta}-FeSi{sub 2} film has a direct energy gap of about 0.85 eV. The thickness of the layer and the refractive index of the film were determined by performed calculation in the wavelength range 1.9-2.7 {mu}m. Furthermore, the Raman spectra of the films were also discussed.

  9. Wettability behavior of water droplet on organic-polluted fused quartz surfaces of pillar-type nanostructures applying molecular dynamics simulation

    Science.gov (United States)

    Chen, Jiaxuan; Chen, Wenyang; Xie, Yajing; Wang, Zhiguo; Qin, Jianbo

    2017-02-01

    Molecular dynamics (MD) is applied to research the wettability behaviors of different scale of water clusters absorbed on organic-polluted fused quartz (FQ) surface and different surface structures. The wettability of water clusters is studied under the effect of organic pollutant. With the combined influence of pillar height and interval, the stair-step Wenzel-Cassie transition critical line is obtained by analyzing stable state of water clusters on different surface structures. The results also show that when interval of pillars and the height of pillars keep constant respectively, the changing rules are exactly the opposite and these are termed as the "waterfall" rules. The substrate models of water clusters at Cassie-Baxter state which are at the vicinity of critical line are chosen to analyze the relationship of HI (refers to the pillar height/interval) ratio and scale of water cluster. The study has found that there is a critical changing threshold in the wettability changing process. When the HI ratio keeps constant, the wettability decreases first and then increase as the size of cluster increases; on the contrary, when the size of cluster keeps constant, the wettability decreases and then increase with the decrease of HI ratio, but when the size of water cluster is close to the threshold the HI ratio has little effect on the wettability.

  10. The Ability of Dental Specialists to Distinguish Lateral Incisor Metal-Free From Porcelain-Fused-to-Metal Implant Supported Crowns.

    Science.gov (United States)

    De Melo, Eduardo V; Kauling, Ana Elisa C; Freitas, Sérgio Fernando T; Cardoso, Antônio C; Ferreira, Cimara Fortes

    2014-12-01

    The objective of this study was to evaluate the ability of dental specialists to distinguish lateral incisor metal-free from porcelain-fused-to-metal implant supported crowns in the anterior region. Five single-tooth implants in the maxillary lateral incisor region were restored with two types of implant-supported crowns (porcelain-fused-to-metal and metal-free). Photographs were presented to 20 evaluators. The evaluators had to answer whether the crown was: metal-free, porcelain-fused-to-metal or they could not tell the difference. The results showed that groups 1 (all participants), 3 (Restorative & Prosthodontic specialists), 4 (graduated 10 years) and 5 (graduated > 10 years) failed to respond correctly (P > 0.05) to which type of crown was presented to them. Group 2 (Periodontology & Implantology specialists) showed an accuracy rate of 35.6% (P = 0.009), in relation to metal-free crowns, 5.6 which is below the random index. The authors concluded that the evaluators from the 5 groups studied were unable to significantly distinguish which type of crown was used in the 10 presented situations.

  11. Fused Zirconia

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    ScopeThis standard specifies the terms,definitions,classification,brands,technical requirements,test methods,inspection rules,packing,marking,transportation,storage,and quality certificate of fused zirconia.This standard is applicable to monoclinic fused zirconia and partially stabilized fused zirconia.

  12. Quartz crystal growth

    Science.gov (United States)

    Baughman, Richard J.

    1992-01-01

    A process for growing single crystals from an amorphous substance that can undergo phase transformation to the crystalline state in an appropriate solvent. The process is carried out in an autoclave having a lower dissolution zone and an upper crystallization zone between which a temperature differential (.DELTA.T) is maintained at all times. The apparatus loaded with the substance, solvent, and seed crystals is heated slowly maintaining a very low .DELTA.T between the warmer lower zone and cooler upper zone until the amorphous substance is transformed to the crystalline state in the lower zone. The heating rate is then increased to maintain a large .DELTA.T sufficient to increase material transport between the zones and rapid crystallization. .alpha.-Quartz single crystal can thus be made from fused quartz in caustic solvent by heating to 350.degree. C. stepwise with a .DELTA.T of 0.25.degree.-3.degree. C., increasing the .DELTA.T to about 50.degree. C. after the fused quartz has crystallized, and maintaining these conditions until crystal growth in the upper zone is completed.

  13. Pressure effect on the sensitivity of quartz Bourdon tube gauges.

    Science.gov (United States)

    Szaniszlo, A. J.

    1972-01-01

    The sensitivity change for a commercial fused quartz Bourdon tube precision pressure gauge, due to a change in absolute pressure level, has been analytically computed and experimentally confirmed. The computed differential pressure error is 2.5% of full scale at a 100 atm absolute pressure level. The experimental method compared the fused quartz Bourdon tube gauge digital output to the results obtained from a nitrogen gas pressure system which had a high pressure, well-type mercury manometer as the differential pressure reference.

  14. Fused silica windows for solar receiver applications

    Science.gov (United States)

    Hertel, Johannes; Uhlig, Ralf; Söhn, Matthias; Schenk, Christian; Helsch, Gundula; Bornhöft, Hansjörg

    2016-05-01

    A comprehensive study of optical and mechanical properties of quartz glass (fused silica) with regard to application in high temperature solar receivers is presented. The dependence of rupture strength on different surface conditions as well as high temperature is analyzed, focussing particularly on damage by devitrification and sandblasting. The influence of typical types of contamination in combination with thermal cycling on the optical properties of fused silica is determined. Cleaning methods are compared regarding effectiveness on contamination-induced degradation for samples with and without antireflective coating. The FEM-aided design of different types of receiver windows and their support structure is presented. A large-scale production process has been developed for producing fused silica dome shaped windows (pressurized window) up to a diameter of 816 mm. Prototypes were successfully pressure-tested in a test bench and certified according to the European Pressure Vessel Directive.

  15. Simulation of quartz resonators

    Science.gov (United States)

    Weinmann, M.; Radius, R.; Mohr, R.

    Quartz resonators are suitable as novel sensor elements in the field of profilometry and three dimensional measurement techniques. This application requires a tailoring of the oscillator circuit which is performed by a network analysis program. The equivalent network parameters are computed by a finite element analysis. The mechanical loading of the quartz is modeled by a viscous damping approach.

  16. Radiation Damage of Quartz Fibers

    CERN Document Server

    Hagopian, V

    1999-01-01

    Quartz fibers are used in high energy physics experiments as the active medium in high radiation area calorimetry. Quartz fibers are also used in the transmission of optical signals. Even though quartz does not damage by moderate amounts of irradiation, the clad of the fibers and the protective coating ( buffer) do damage reducing light transmission. Various types of quartz fibers have been irradiated and measured for light transmission. The most radiation hard quartz fibers are those with quartz clad and aluminum buffer.

  17. Polymer optical fiber fuse

    CERN Document Server

    Mizuno, Yosuke; Tanaka, Hiroki; Nakamura, Kentaro

    2013-01-01

    Although high-transmission-capacity optical fibers are in demand, the problem of the fiber fuse phenomenon needs to be resolved to prevent the destruction of fibers. As polymer optical fibers become more prevalent, clarifying their fuse properties has become important. Here, we experimentally demonstrate a fuse propagation velocity of 21.9 mm/s, which is 1 to 2 orders of magnitude slower than that in standard silica fibers. The achieved threshold power density and proportionality constant between the propagation velocity and the power density are respectively 1/186 of and 16.8 times the values for silica fibers. An oscillatory continuous curve instead of periodic voids is formed after the passage of the fuse. An easy fuse termination method is presented herein, along with its potential plasma applications.

  18. QUARTZ FIBER ELECTROSCOPES

    Science.gov (United States)

    Henderson, R.P.

    1957-09-17

    An instrument carried unobtrusively about the person such as in a finger ring to indicate when that person has been exposed to an unusual radiation hazard is described. A metallized quartz fiber is electrically charged to indicate a full scale reading on an etched glass background. The quartz fiber and the scale may be viewed through a magnifying lens for ease of reading. Incident radiation will ionize gaseous particles in the sealed structure thereby allowing the charge to leak off the quartz fiber with its resulting movement across the scale proportionally indicating the radiation exposure.

  19. Nanocrystalline diamond in carbon implanted SiO{sub 2}.

    Energy Technology Data Exchange (ETDEWEB)

    Tsoi, K.A.; Prawer, S.; Nugent, K.W.; Walker, R. J.; Weiser, P.S. [Melbourne Univ., Parkville, VIC (Australia). School of Physics

    1996-12-31

    Recently, it was reported that nanocrystalline diamond can be produced via laser annealing of a high dose C implanted fused quartz (SiO{sub 2}) substrate. The aim of this investigation is to reproduce this result on higher C{sup +} dose samples and the non-implanted silicon sample, as well as optimise the power range and annealing time for the production of these nanocrystals of diamond. In order to provide a wide range of laser powers the samples were annealed using an Ar ion Raman laser. The resulting annealed spots were analysed using scanning electron microscopy (SEM) and Raman analysis. These techniques are employed to determine the type of bonding produced after laser annealing has occurred. 4 refs., 5 figs.

  20. Vacuum electrolysis of quartz

    Science.gov (United States)

    King, James Claude

    1976-01-13

    The disclosure is directed to a method for processing quartz used in fabricating crystal resonators such that transient frequency change of resonators exposed to pulse irradiation is virtually eliminated. The method involves heating the crystal quartz in a hydrogen-free atmosphere while simultaneously applying an electric field in the Z-axis direction of the crystal. The electric field is maintained during the cool-down phase of the process.

  1. Functional Use Database (FUse)

    Data.gov (United States)

    U.S. Environmental Protection Agency — There are five different files for this dataset: 1. A dataset listing the reported functional uses of chemicals (FUse) 2. All 729 ToxPrint descriptors obtained from...

  2. Ductile Regime Single Point Diamond Turning of Quartz

    Science.gov (United States)

    Ravindra, Deepak; Patten, John

    2011-01-01

    Quartz (fused silica) is one of the advanced engineered ceramic materials designed to operate in extreme environments. The mechanics of material removal in glass (Quartz) can be classified in two categories; brittle fracture and ductile plastic deformation. Good optical quality surfaces can be achieved by removing the material in a ductile manner. The strength, hardness and fracture toughness of the work piece material are the governing factors that control the extent of brittle fracture. The main goal of the subject research is to improve the surface quality of Quartz to be used as an optic device (mirrors and windows) via single point diamond turning (SPDT). Surface roughness (Ra) values of less than 50 nm without sub surface damage were obtained.

  3. Quartz Crystal Microbalance Data

    Energy Technology Data Exchange (ETDEWEB)

    Baxamusa, S H

    2011-11-16

    We are using a Qpod quartz crystal microbalance (manufactured by Inficon) for use as a low-volume non-volatile residue analysis tool. Inficon has agreed to help troubleshoot some of our measurements and are requesting to view some sample data, which are attached. The basic principle of an NVR analysis is to evaporate a known volume of solvent, and weigh the remaining residue to determine the purity of the solvent. A typical NVR analysis uses 60 g of solvent and can measure residue with an accuracy of +/- 0.01 mg. The detection limit is thus (0.01 mg)/(60 g) = 0.17 ppm. We are attempting to use a quartz crystal microbalance (QCM) to make a similar measurement. The attached data show the response of the QCM as a 5-20 mg drop of solvent evaporates on its surface. The change in mass registered by the QCM after the drop evaporates is the residue that deposits on the crystal. On some measurements, the change in mass in less than zero, which is aphysical since the drop will leave behind {>=}0 mass of residue. The vendor, Inficon, has agreed to look at these data as a means to help troubleshoot the cause.

  4. Quartz resonator processing system

    Science.gov (United States)

    Peters, Roswell D. M.

    1983-01-01

    Disclosed is a single chamber ultra-high vacuum processing system for the oduction of hermetically sealed quartz resonators wherein electrode metallization and sealing are carried out along with cleaning and bake-out without any air exposure between the processing steps. The system includes a common vacuum chamber in which is located a rotatable wheel-like member which is adapted to move a plurality of individual component sets of a flat pack resonator unit past discretely located processing stations in said chamber whereupon electrode deposition takes place followed by the placement of ceramic covers over a frame containing a resonator element and then to a sealing stage where a pair of hydraulic rams including heating elements effect a metallized bonding of the covers to the frame.

  5. Densification and Devitrification of Fused Silica Induced by Ballistic Impact: A Computational Investigation

    Directory of Open Access Journals (Sweden)

    Mica Grujicic

    2015-01-01

    Full Text Available A molecular-level computational investigation is carried out to determine the dynamic response and material topology changes of fused silica subjected to ballistic impact by a hard projectile. The analysis was focused on the investigation of specific aspects of the dynamic response and of the topological changes such as the deformation of highly sheared and densified regions, and the conversion of amorphous fused silica to SiO2 crystalline polymorphs (in particular, α-quartz and stishovite. The topological changes in question were determined by carrying out a postprocessing atom-coordination procedure. This procedure suggested the formation of stishovite (and perhaps α-quartz within fused silica during ballistic impact. To rationalize the findings obtained, the all-atom molecular-level computational analysis is complemented by a series of quantum-mechanics density functional theory (DFT computations. The latter computations enable determination of the relative potential energies of the fused silica, α-quartz and stishovite, under ambient pressure (i.e., under their natural densities as well as under imposed (as high as 50 GPa pressures (i.e., under higher densities and shear strains. In addition, the transition states associated with various fused-silica devitrification processes were identified. The results obtained are found to be in good agreement with their respective experimental counterparts.

  6. Electrochemical Quartz Crystal Nanobalance

    Science.gov (United States)

    Inzelt, György

    The method of piezoelectric microgravimetry (nanogravimetry) using an electrochemical quartz crystal microbalance (EQCM) or nanobalance (EQCN) can be considered as a novel and much more sensitive version of electrogravimetry. The EQCN technique has become a widely used technique in several areas of electrochemistry, electroanalytical chemistry, bioelectrochemistry, etc. [1-10]. Obviously, mass changes occurring during adsorption, sorption, electrosorption, electrodeposition, or spontaneous deposition can be followed, which is very helpful for the elucidation of reaction mechanism via identification of the species accumulated on the surface. These investigations include metal and alloy deposition, underpotential deposition, electroplating, synthesis of conducting polymers by electropolymerization, adsorption of biologically active materials, and analytical determination of small ions and biomolecules. Of course, the opposite processes, i.e., spontaneous dissolution, electrodissolution, corrosion, can also be studied. Electrochemical oscillations, in which the formation and oxidation of chemisorbed molecular fragments play a determining role, have been studied, too. The majority of the investigations have been devoted to ion and solvent transport associated with the redox transformations of electrochemically active polymers. Similar studies have been carried out regarding polynuclear surface layers such as metal hexacyanometalates as well as inorganic and organic microcrystals of different compositions.

  7. Fused-Polished Fiber Couplers

    Institute of Scientific and Technical Information of China (English)

    Sien; Chi; Shiao-Min; Tseng

    2003-01-01

    We report on fused-polished fiber couplers with a new fabrication method. This structure so fabricated is promising while achieving high-performance all-fiber WDM devices. Potential advantages and prospects of our works are presented.

  8. Thermal fatigue of electrical fuses

    Directory of Open Access Journals (Sweden)

    Gelet Jean-Louis

    2014-06-01

    Full Text Available Electric Fuses have to respect different national or international standards such as IEC (International Electro-technical Commission 269. These standards define the characteristics of the fuses and describe the tests to be run in order to check fuse's ability to take up their main functions, i.e. current-conduction and operation under overloads and short-circuits. But fuses never carry current neither operate under standardized conditions. For example, rated current is evaluated under specified ambient temperature, without cooling air-flow, and with 1 meter-long connection-cables on both sides. In the field, temperature can reach up 80∘C, with or without air-flow and connection-parts are much more shorter. An issue is that current is never constant, often being cyclingly applied; equipments are frequently in use during the day and stopped in the night. ON-time and OFF-time generate alternative heating, then alternative stresses leading to thermal fatigue. MERSEN run many tests along the years, allowing to develop a method for choosing right fuses for each application. As a result, fuses don't melt unexpectedly in the field, but the method is supposed to be conservative and does not permit to get a better understanding of the phenomena neither an improvement of the products. The paper presents some specific ageing-tests run on conductive elements and tries to establish a correspondence between these tests and others carried out on complete fuses. Tests have been run on silver and copper, but their principle could be interesting for any structural material, especially because it underlines crack-opening.

  9. Fabrication and properties of TiO2 nanofilms on different substrates by a novel and universal method of Ti-ion implantation and subsequent annealing.

    Science.gov (United States)

    Ren, Feng; Zhou, Xiao-Dong; Liu, Yi-Chao; Wang, Yong-Qiang; Cai, Guang-Xu; Xiao, Xiang-Heng; Dai, Zhi-Gao; Li, Wen-Qing; Yan, Shao-Jian; Wu, Wei; Zhang, Chao; Ni, Hong-Wei; Jiang, Chang-Zhong

    2013-06-28

    We report a new, novel and universal method to fabricate high-quality titanium dioxide (TiO2) nanofilms on different substrates by a solid phase growth process of ion implantation and subsequent annealing in oxygen atmosphere. Ti ions were implanted into fused silica, soda lime glass, Z-cut quartz, or (0001) α-sapphire by a metal vapor vacuum arc (MEVVA) ion source implanter to fluences of 0.75, 1.5 and 3 × 10(17) ions cm(-2) with a nominal accelerating voltage of 20 kV. To understand the influence of the annealing temperature, time, and substrate on the formation and phase transformation of the TiO2 nanofilms, the Ti-ion-implanted substrates were annealed in oxygen atmosphere from 500 to 1000 °C for 1-6 h. The formation of TiO2 nanofilms resulted from the slow out-diffusion of implanted Ti ions from the substrates which were then oxidized at the surfaces. The thickness and phase of the nanofilms can be tailored by controlling the implantation and annealing parameters. Since the TiO2 nanofilms are formed under high temperature and low growth rate, they show good crystallinity and antibacterial properties, with good film adhesion and stability, suggesting that the TiO2 nanofilms formed by this method have great potential in applications such as antibacterial and self-cleaning transparent glass.

  10. Fabrication and properties of TiO2 nanofilms on different substrates by a novel and universal method of Ti-ion implantation and subsequent annealing

    Science.gov (United States)

    Ren, Feng; Zhou, Xiao-Dong; Liu, Yi-Chao; Wang, Yong-Qiang; Cai, Guang-Xu; Xiao, Xiang-Heng; Dai, Zhi-Gao; Li, Wen-Qing; Yan, Shao-Jian; Wu, Wei; Zhang, Chao; Ni, Hong-Wei; Jiang, Chang-Zhong

    2013-06-01

    We report a new, novel and universal method to fabricate high-quality titanium dioxide (TiO2) nanofilms on different substrates by a solid phase growth process of ion implantation and subsequent annealing in oxygen atmosphere. Ti ions were implanted into fused silica, soda lime glass, Z-cut quartz, or (0001) α-sapphire by a metal vapor vacuum arc (MEVVA) ion source implanter to fluences of 0.75, 1.5 and 3 × 1017 ions cm-2 with a nominal accelerating voltage of 20 kV. To understand the influence of the annealing temperature, time, and substrate on the formation and phase transformation of the TiO2 nanofilms, the Ti-ion-implanted substrates were annealed in oxygen atmosphere from 500 to 1000 ° C for 1-6 h. The formation of TiO2 nanofilms resulted from the slow out-diffusion of implanted Ti ions from the substrates which were then oxidized at the surfaces. The thickness and phase of the nanofilms can be tailored by controlling the implantation and annealing parameters. Since the TiO2 nanofilms are formed under high temperature and low growth rate, they show good crystallinity and antibacterial properties, with good film adhesion and stability, suggesting that the TiO2 nanofilms formed by this method have great potential in applications such as antibacterial and self-cleaning transparent glass.

  11. Infrared transmission at the 3.39 micron helium-neon laser wavelength in liquid-core quartz fibers

    Science.gov (United States)

    Majumdar, A. K.; Hinkley, E. D.; Menzies, R. T.

    1979-01-01

    Infrared transmission at the 3.39 micron helium-neon laser wavelength has been measured in a tetrachloroethylene-filled fused-quartz fiber. The loss measurements were taken for three different settings of laser light intensity using a series of neutral density filters. The average value of transmission loss at this wavelength was found to be 56 dB/km.

  12. Electromodulated absorption in smoky quartz

    NARCIS (Netherlands)

    Brom, W.E. van den; Volger, J.

    1974-01-01

    The optical absorption coefficient of “smoky” quartz (containing aluminium) can be modulated by applying an electric field. The effect saturates at high fields and low temperatures and reaches a maximum at 535 nm. The results are discussed in terms of a model consisting of a colour centre, dipolar i

  13. Liquefier Dynamics in Fused Deposition

    DEFF Research Database (Denmark)

    Bellini, Anna; Guceri, Selcuk; Bertoldi, Maurizio

    2004-01-01

    Layered manufacturing (LM) is an evolution of rapid prototyping (RP) technology whereby a part is built in layers. Fused deposition modeling (FDM) is a particular LM technique in which each section is fabricated through vector style deposition of building blocks, called roads, which...

  14. Breast Implants

    Science.gov (United States)

    ... Medical Procedures Implants and Prosthetics Breast Implants Breast Implants Share Tweet Linkedin Pin it More sharing options Linkedin Pin it Email Print Breast implants are medical devices that are implanted under the ...

  15. Shock metamorphism of deformed quartz

    Science.gov (United States)

    Gratz, Andrew J.; Christie, John; Tyburczy, James; Ahrens, Thomas; Pongratz, Peter

    1988-01-01

    The effect produced by shock loading (to peak pressures of 12 and 24) on deformed synthetic quartz containing a dislocation and abundant bubbles and small inclusions was investigated, and the relationships between preexisting dislocation density shock lamellae in the target material were examined. The resultant material was found to be inhomogeneously deformed and extremely fractured. Results of TEM examinations indicate that no change in dislocation density was caused by shock loading except in regions containing shock lamellae, where the dislocation density was lowered. The shock-induced defects tend to nucleate on and be controlled by preexisting stress concentrators; shock lamellae, glassy veins, and most curviplanar defects form in tension, presumably during release. An extremely mobile silica fluid is formed and injected into fractures during release, which forcibly removes crystalline fragments from vein walls. It is concluded that shock deformation in quartz is dominated by fracture and melting.

  16. Formation, migration, and clustering energies of interstitial He in α-quartz and β-cristobalite

    Science.gov (United States)

    Lin, Kan-Ju; Ding, Hepeng; Demkowicz, Michael J.

    2016-10-01

    Precipitation of implanted helium (He) is detrimental to many nuclear materials. A solid in which implanted He does not precipitate, but rather remains in solution and diffuses readily is potentially of interest for applications requiring resistance to He-induced damage. We use density functional theory (DFT) calculations to examine He interstitial formation, migration, and clustering energies in two SiO2 polymorphs: α-quartz and β-cristobalite. Our findings show greater He solubility and mobility in the latter than in the former. This difference appears to be due primarily to the unlike atomic-level structures of α-quartz and β-cristobalite, rather than their differing densities. Our findings also suggest that He is unlikely to cluster in either material. The behavior of He in α-quartz and β-cristobalite, and similar forms of silica make them promising materials for further investigation for potential use in applications requiring resistance to He-induced damage.

  17. Luminescence sensitivity changes in quartz

    CERN Document Server

    Wintle, A G

    1999-01-01

    In the luminescence dating of sedimentary or heated quartz, some heat treatment is usually applied to the sample immediately prior to the measurement of the optically stimulated luminescence. In this paper we report experiments on a 30,000-year-old sedimentary quartz, in which we use the luminescence response to a test dose to monitor the changes in sensitivity that are caused by holding the quartz at temperatures from 160 to 280 deg. C for times from 10 s to 22 h. For an optically bleached sample, the monitoring is by both optically stimulated luminescence and the 110 deg. C TL peak; both luminescence signals are shown to have the same sensitisation (i.e. activation energy) characteristics. For natural or laboratory irradiated samples only the 110 deg. C TL peak can be used; sensitivity increases of up to a factor of 1.3 and 3 are observed for the natural and laboratory irradiated aliquots, respectively. Up to four exponential components are used to deconvolve the sensitivity change data; the dominant compon...

  18. Cathodoluminescence and epitaxy after laser annealing of Cs{sup +}-irradiated {alpha}-quartz

    Energy Technology Data Exchange (ETDEWEB)

    Sahoo, P.K. [II. Physikalisches Institut, Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany); Gasiorek, S. [II. Physikalisches Institut, Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany); Dhar, S. [II. Physikalisches Institut, Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany); Lieb, K.P. [II. Physikalisches Institut, Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany); Schaaf, P. [II. Physikalisches Institut, Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany)]. E-mail: pschaaf@uni-goettingen.de

    2006-04-30

    In the course of a systematic investigation of dynamic, chemical, and laser-induced solid phase epitaxy of {alpha}-quartz after ion implantation, we have studied epitaxy and cathodoluminescence emission after 250 keV Cs-ion implantation and subsequent pulsed excimer laser treatment in air. Rutherford backscattering channelling analysis showed partial epitaxy for all the laser-irradiated samples; however, no full epitaxy was achieved. The optical properties of these samples were analyzed using cathodoluminescence spectroscopy, giving evidence of five emission bands at 2.42, 2.79, 3.25, 3.65, and 4.30 eV photon energy. Their intensity relation to the laser power and retained Cs-ion fraction are discussed and the present results will be compared with those obtained after chemical and dynamic epitaxy of quartz after alkali-ion, Ge, and Ba implantation.

  19. Penile Implants

    Science.gov (United States)

    ... the discussion with your doctor. Types of penile implants There are two main types of penile implants: ... might help reduce the risk of infection. Comparing implant types When choosing which type of penile implant ...

  20. Crown color match of implant-supported zirconia and porcelain-fused-to-metal restorations:a spectrophotometric comparison%采用分光光度计比较种植支持式氧化锆全瓷和贵金属金瓷修复的牙冠颜色

    Institute of Scientific and Technical Information of China (English)

    彭敏; 费伟; Mandana Hosseini; Klaus Gotfredsen

    2014-01-01

    Objective This study aimed to compare the crown color match of implant-supported zirconia restorations and porcelain-fused-to-metal (PFM) restorations in the anterior maxillary region through spectrophotometric evaluation. Methods Eighteen patients with 29 implant-supported single crowns in the anterior maxillary area were recruited. Eleven of the implant crowns were zirconia restorations and 18 were PFM restorations. Color matching of the implant crown with contra-lateral/neighboring tooth at the position of body 1/3 of the crown was assessed using a spectrophotometer (SpectroShadeTM) in CIE L*a*b* coordinates. Subjective crown color match scores were evaluated. Independent sample t test of SPSS 17.0 was used to compare the difference between zirconia restoration and PFM restoration. Spearman correlation was used to analyze the relationship between the spectrophotometric color difference and the subjective crown color match score. Descriptive statistics was used to analyze the distribution of color coordinates of natural anterial teeth. Results The crown color of the implant-supported zirconia restorations and PFM restorations were both lighter than that of natural teeth (ΔL, 4.5±3.2, 1.0±2.6). The lightness difference induced by zirconia restorations was significantly larger than that induced by PFM restorations (P=0.004). The spectrophotometric crown color difference (ΔE) induced by zirconia restorations (7.0±2.8) was significantly larger than that induced by PFM restorations (4.0±1.9) (P=0.002), and both values were beyond the clinical thresholds (3.7). Conclusion The spectrophotometric crown color difference induced by zirconia restorations was significantly larger than that induced by PFM restorations. However, they were indistinguishable in subjective evaluation.%目的:应用一种小型分光光度计对上前牙区种植支持式氧化锆全瓷修复与贵金属金瓷修复的牙冠颜色进行比较,为临床选择修复材料提

  1. The Problem of using Quartz as a radiation dosimeter: fundamentals of dose dependence

    Science.gov (United States)

    King, G. E.; Finch, A. A.; Robinson, R. A. J.; Hole, D. E.

    2009-04-01

    Quartz is widely used as a radiation dosimeter in Quaternary geomorphological and archaeological dating applications through Optically Stimulated Luminescence (over 1,200 journal publications since 2000). However, obtaining an accurate equivalent radiation dose (DE) can be challenging, especially where the luminescence intensity of the quartz is dim. The causes of variation in luminescence intensity between quartz grains of different provenances, transport and thermal histories is unknown, however it has been suggested that it relates to either the dosimetric history of the grain, or mechanical processes which occur in transit. Investigation of the fundamental properties of the luminescence of quartz, enables investigation of dose dependent changes in luminescence intensity. A series of dose dependence experiments were conducted using spectroscopic ionoluminescence, which comprises the excitation of quartz with protons accelerated at 0.95 MeV. The energy delivered to the sample throughout ion implantation is similar to that received during gamma irradiation, and thus approximates sample radiation dosing. A natural macro-crystal of α-quartz was investigated parallel and perpendicular to c, to observe any orientation dependent effects, as well as a calibration quartz from the Risø National Laboratory, Denmark, and a Scottish geomorphological sample, prepared using standard laboratory procedures. The calibration quartz sample has excellent luminescence intensity and is suited to analysis using the single-aliquot regenerative dose (SAR) standard OSL protocol, the Scottish sample alternatively has very dim luminescence and exhibits variable behaviour when analysed with SAR. Despite the differences between the luminescence behaviour of the samples, all three responded to the dose dependence experiments in a similar manner. The UV/blue emission was observed to deplete with increasing dose, whereas the red emission, not normally analysed within OSL, exhibited increased

  2. Development of Quartz Fiber Calorimetry

    CERN Multimedia

    2002-01-01

    % RD40 \\\\ \\\\ Very Forward Calorimeters (VFCs) in LHC detectors should cover the pseudorapidity range from $\\eta$~=~2.5 to at least $\\eta$~=~5 in order to compute missing transverse energy and for jet tagging. Operation at such high rapidity requires the use of a calorimetry technique that is very radiation resistant, fast and insensitive to radioactivity (especially to neutrons). This can be accomplished through the Quartz-Calorimeter~(Q-Cal) concept of embedding silica core fibers, that resist to the Gigarad radiation level, into an absorber. In this calorimeter the shower particles produce light through the Cherenkov effect generating a signal less than 10~ns in duration. Unique to this new technology the visible energy of hadronic showers has a transverse dimension nearly an order of magnitude smaller than that in conventional calorimeters, enabling precise spatial resolution, sharper isolation cuts and better jet recognition against the minimum bias events background. Last but not least, most radioactive ...

  3. About a New Type of Fuse Based on the Controllable Fusing Effect

    Directory of Open Access Journals (Sweden)

    PLESCA, A.

    2009-06-01

    Full Text Available Fuses are among the best known of electrical devices and there are an extremely large number in use throughout the world. Beside of the advantageous features, the nowadays fuses have certain drawbacks. Therefore, a new type of fuse based on controllable fusing concept is proposed and a study as regards the total clearing time is done. The new concept has been validated through many experimental tests at different current values. The new type of fuse based on controllable fusing concept can be integrated within an overcurrent protection system especially to protect power semiconductors where the Joule integral criterion is better satisfied.

  4. Dynamic simulation of flywheel-type fuses

    OpenAIRE

    Editorial Office

    1996-01-01

    Rounds of ammunition are normally armed with a fuse. In this study, a fuse is developed which uses a flywheel-type mechanism controlled by time or distance. Due to its simplicity of operation and construction, the concept is expected to have high reliabil­ity. The dynamic response of all the components of this flywheel-type fuse is mathematically modelled. Simulation software was developed which connects the mathematical models of the various components. With the definition of boundary value...

  5. The Quartz Analog Watch: A Wonder Machine.

    Science.gov (United States)

    Crane, H. Richard, Ed.

    1993-01-01

    Summarizes how a quartz watch works. Discusses the quartz crystal, its form, and how its frequency is set to a standard; the integrated circuit chip that drives the crystal in vibration, scales its frequency down, and forms pulses that turn the motor; and the motor that drives the gear train that turns the hands. (ZWH)

  6. FUSE Observations of eta Carinae

    CERN Document Server

    Iping, R C; Gull, T R

    2004-01-01

    Eta Carinae was observed by FUSE through the LWRS (30 arcsec x30 arcsec) and HIRS (1.25 arcsec x 20 arcsec) apertures in March and April 2004. There are significant differences between the two spectra. About half of the LWRS flux appears to be due to two B-type stars near the edge of the LWRS aperture, 14 arcsec from eta Carinae. The HIRS spectrum (LiF1 channel) therefore reveals the intrinsic FUV spectrum of eta Carinae without this stellar contamination. The HIRS spectrum contains strong interstellar H2 having high rotational excitation (up to J=8). Most of the atomic species with prominent ISM features (C II, Fe II, Ar I, P II, etc) also have strong blue-shifted absorption to v= ~ -580 km/s that is associated with expanding debris from the 1840 eruption.

  7. Fused combiners for photonic crystal bers

    DEFF Research Database (Denmark)

    Noordegraaf, Danny

    The work presented in this Ph.D. thesis focuses on the fabrication of fused combiners for high-power fiber lasers and amplifiers. The main focus of the Ph.D. project was to further develop the fused pump combiners for airclad photonic crystal bers (PCFs), and implement a signal feed...

  8. Mechanical twinning in small quartz crystals

    Science.gov (United States)

    Laughner, J. W.; Newnham, R. E.; Cross, L. E.

    1982-02-01

    Quartz is known to be ferrobielastic; that is, quartz crystals have domain states (Dauphiné twins) which differ in their elastic compliance values and which can be switched by an appropriately oriented stress. Polycrystalline quartz has also been reported (Tullis 1970) to show preferential orientation of these domains following application of large uniaxial stresses. These experiments were designed to study twinning of synthetic quartz “grains” (minimum size 0.07×0.07×0.02 cm) in specially-constructed composites and of grains in three natural quartz aggregates — a quartzite, a novaculite, and a jasper. Backreflection X-ray techniques were used to verify twinning in the composite grains, while special electroding and electrical detection allowed the twinning processes to be examined in “real time.” Small synthetic quartz crystals were found to behave identically to the massive samples previously studied. Electrical pulses due to the reversal of piezoelectric coefficient d 11 in twinned quartz were detected from quartzite and from the man-made composites. Novaculite also gave electrical pulses which were probably from twinning (evidenced by the correlation of expected and observed pulse sizes and shapes), while no pulses from the jaspers indicative of twinning were detected. Grain size distribution differences are considered the main structural reason for the different behaviors.

  9. Dental Implants.

    Science.gov (United States)

    Griggs, Jason A

    2017-10-01

    Systematic reviews of literature over the period between 2008 and 2017 are discussed regarding clinical evidence for the factors affecting survival and failure of dental implants. The factors addressed include publication bias, tooth location, insertion torque, collar design, implant-abutment connection design, implant length, implant width, bone augmentation, platform switching, surface roughness, implant coatings, and the use of ceramic materials in the implant body and abutment. Copyright © 2017 Elsevier Inc. All rights reserved.

  10. SAW Temperature Sensor on Quartz.

    Science.gov (United States)

    Zhgoon, Sergei; Shvetsov, Alexander; Ancev, Ivan; Bogoslovsky, Sergei; Sapozhnikov, Gennadiy; Trokhimets, Konstantin; Derkach, Mikhail

    2015-06-01

    For biomedical applications, narrow temperature range and high sensor accuracy requirements define the need for high temperature sensitivity. Wireless SAW sensors connected to antennas need a reference element to account for changes in electromagnetic coupling between the transmitter and receiver antennas. A pair of sensors with different temperature sensitivities may serve as a self-referenced sensor assembly. This justifies the need for materials with useful SAW resonator properties and with the largest difference between temperature coefficients of frequency (TCF) for a resonator pair on a single substrate. We have identified several cuts of quartz having useful properties with a TCF difference up to 140 ppm/°C for a pair of resonators on a single substrate. As a rule, placing such resonators on a single substrate requires their rotation by up to 90° relative to each other. The limited range of cuts presents a unique opportunity to place both resonators along the X+90° direction with one resonator using Bleustein-Gulyaev-Shimizu (BGS) waves (with electrodes placed along the x-axis) and the other one (with electrodes inclined by about ±10° to the x-axis) using quasi-Rayleigh waves. These cuts are close to the 70°Y cut where a high TCF difference is reached together with acceptable characteristics of the resonators. Resonators were designed for all useful cuts (including the 70°Y cut) and tested. The use of different periods in reflectors and interdigital transducer (IDT) together with individual choice of gaps between reflectors and IDT meant achieving low spurious content in resonator responses. The quality factors reached values up to 3500 at central frequencies around 915 MHz for both BGS and quasi-Rayleigh types of waves. The measured difference of the TCF is about 138 ppm/°C on 70°Y cut that is close to the calculated value.

  11. Quartz-Enhanced Photoacoustic Spectroscopy: A Review

    Directory of Open Access Journals (Sweden)

    Pietro Patimisco

    2014-03-01

    Full Text Available A detailed review on the development of quartz-enhanced photoacoustic sensors (QEPAS for the sensitive and selective quantification of molecular trace gas species with resolved spectroscopic features is reported. The basis of the QEPAS technique, the technology available to support this field in terms of key components, such as light sources and quartz-tuning forks and the recent developments in detection methods and performance limitations will be discussed. Furthermore, different experimental QEPAS methods such as: on-beam and off-beam QEPAS, quartz-enhanced evanescent wave photoacoustic detection, modulation-cancellation approach and mid-IR single mode fiber-coupled sensor systems will be reviewed and analysed. A QEPAS sensor operating in the THz range, employing a custom-made quartz-tuning fork and a THz quantum cascade laser will be also described. Finally, we evaluated data reported during the past decade and draw relevant and useful conclusions from this analysis.

  12. Quartz-enhanced photoacoustic spectroscopy: a review.

    Science.gov (United States)

    Patimisco, Pietro; Scamarcio, Gaetano; Tittel, Frank K; Spagnolo, Vincenzo

    2014-03-28

    A detailed review on the development of quartz-enhanced photoacoustic sensors (QEPAS) for the sensitive and selective quantification of molecular trace gas species with resolved spectroscopic features is reported. The basis of the QEPAS technique, the technology available to support this field in terms of key components, such as light sources and quartz-tuning forks and the recent developments in detection methods and performance limitations will be discussed. Furthermore, different experimental QEPAS methods such as: on-beam and off-beam QEPAS, quartz-enhanced evanescent wave photoacoustic detection, modulation-cancellation approach and mid-IR single mode fiber-coupled sensor systems will be reviewed and analysed. A QEPAS sensor operating in the THz range, employing a custom-made quartz-tuning fork and a THz quantum cascade laser will be also described. Finally, we evaluated data reported during the past decade and draw relevant and useful conclusions from this analysis.

  13. Electronic dipole resonance in smoky quartz

    NARCIS (Netherlands)

    Kerssen, J.; Volger, J.

    1967-01-01

    Microwave absorption in smoky quartz mono-crystal is ascribed to resonance transitions of trapped electrons between initially configurational degenerated states, which are Stark-splitted by a polarizing electric field.

  14. Quartz Mountain/Oklahoma Summer Arts Institute.

    Science.gov (United States)

    Frates, Mary Y.; Madeja, Stanley S.

    1982-01-01

    Describes the Quartz Mountain Oklahoma Summer Arts Institute program. It is designed to nurture artistic talent and to provide intensive arts experiences in music, dance, theater, and the visual arts for talented students aged 14-18. (AM)

  15. Porphyrins Fused with Unactivated Polycyclic Aromatic Hydrocarbons

    KAUST Repository

    Diev, Vyacheslav V.

    2012-01-06

    A systematic study of the preparation of porphyrins with extended conjugation by meso,β-fusion with polycyclic aromatic hydrocarbons (PAHs) is reported. The meso-positions of 5,15-unsubstituted porphyrins were readily functionalized with PAHs. Ring fusion using standard Scholl reaction conditions (FeCl 3, dichloromethane) occurs for perylene-substituted porphyrins to give a porphyrin β,meso annulated with perylene rings (0.7:1 ratio of syn and anti isomers). The naphthalene, pyrene, and coronene derivatives do not react under Scholl conditions but are fused using thermal cyclodehydrogenation at high temperatures, giving mixtures of syn and anti isomers of the meso,β-fused porphyrins. For pyrenyl-substituted porphyrins, a thermal method gives synthetically acceptable yields (>30%). Absorption spectra of the fused porphyrins undergo a progressive bathochromic shift in a series of naphthyl (λ max = 730 nm), coronenyl (λ max = 780 nm), pyrenyl (λ max = 815 nm), and perylenyl (λ max = 900 nm) annulated porphyrins. Despite being conjugated with unsubstituted fused PAHs, the β,meso-fused porphyrins are more soluble and processable than the parent nonfused precursors. Pyrenyl-fused porphyrins exhibit strong fluorescence in the near-infrared (NIR) spectral region, with a progressive improvement in luminescent efficiency (up to 13% with λ max = 829 nm) with increasing degree of fusion. Fused pyrenyl-porphyrins have been used as broadband absorption donor materials in photovoltaic cells, leading to devices that show comparatively high photovoltaic efficiencies. © 2011 American Chemical Society.

  16. Intensity of quartz cathodoluminescence and trace-element content in quartz from the porphyry copper deposit at Butte, Montana

    Science.gov (United States)

    Rusk, B.G.; Reed, M.H.; Dilles, J.H.; Kent, A.J.R.

    2006-01-01

    Textures of hydrothermal quartz revealed by cathodoluminescence using a scanning electron microscope (SEM-CL) reflect the physical and chemical environment of quartz formation. Variations in intensity of SEM-CL can be used to distinguish among quartz from superimposed mineralization events in a single vein. In this study, we present a technique to quantify the cathodoluminescent intensity of quartz within individual and among multiple samples to relate luminescence intensity to specific mineralizing events. This technique has been applied to plutonic quartz and three generations of hydrothermal veins at the porphyry copper deposit in Butte, Montana. Analyzed veins include early quartz-molybdenite veins with potassic alteration, pyrite-quartz veins with sericitic alteration, and Main Stage veins with intense sericitic alteration. CL intensity of quartz is diagnostic of each mineralizing event and can be used to fingerprint quartz and its fluid inclusions, isotopes, trace elements, etc., from specific mineralizing episodes. Furthermore, CL intensity increases proportional to temperature of quartz formation, such that plutonic quartz from the Butte quartz monzonite (BQM) that crystallized at temperatures near 750 ??C luminesces with the highest intensity, whereas quartz that precipitated at ???250 ??C in Main Stage veins luminesces with the least intensity. Trace-element analyses via electron microprobe and laser ablation-ICP-MS indicate that plutonic quartz and each generation of hydrothermal quartz from Butte is dominated by characteristic trace amounts of Al, P, Ti, and Fe. Thus, in addition to CL intensity, each generation of quartz can be distinguished based on its unique trace-element content. Aluminum is generally the most abundant element in all generations of quartz, typically between 50 and 200 ppm, but low-temperature, Main Stage quartz containing 400 to 3600 ppm Al is enriched by an order of magnitude relative to all other quartz generations. Phosphorous

  17. Dynamic simulation of flywheel-type fuses

    Directory of Open Access Journals (Sweden)

    Editorial Office

    1996-07-01

    Full Text Available Rounds of ammunition are normally armed with a fuse. In this study, a fuse is developed which uses a flywheel-type mechanism controlled by time or distance. Due to its simplicity of operation and construction, the concept is expected to have high reliabil­ity. The dynamic response of all the components of this flywheel-type fuse is mathematically modelled. Simulation software was developed which connects the mathematical models of the various components. With the definition of boundary values, the response of the projectile, flywheel and other components can be determined continuously for firing and in-flight conditions.

  18. Coordination chemistry in fused-salt solutions

    Science.gov (United States)

    Gruen, D. M.

    1969-01-01

    Spectrophotometric work on structural determinations with fused-salt solutions is reviewed. Constraints placed on the method, as well as interpretation of the spectra, are discussed with parallels drawn to aqueous spectrophotometric curves of the same materials.

  19. Fuse Protects Parabolic-Dish Solar Collector

    Science.gov (United States)

    Selcuk, M. K.

    1983-01-01

    Sliding barrel and shutter protect against overheating. Downward movement of shutter initiated by melting of fuse wire that suspends it. Shutter lowered or raised under operator's control by depressuring or pressurizing hydraulic cylinder.

  20. Organometallic chemistry: Fused ferrocenes come full circle

    Science.gov (United States)

    Musgrave, Rebecca A.; Manners, Ian

    2016-09-01

    Chemists have long been fascinated by electron delocalization, from both a fundamental and applied perspective. Macrocyclic oligomers containing fused ferrocenes provide a new structural framework -- containing strongly interacting metal centres -- that is capable of supporting substantial charge delocalization.

  1. The effect of high-pressure devitrification and densification on ballistic-penetration resistance of fused silica

    Science.gov (United States)

    Avuthu, Vasudeva Reddy

    Despite the clear benefits offered by more advanced transparent materials, (e.g. transparent ceramics offer a very attractive combination of high stiffness and high hardness levels, highly-ductile transparent polymers provide superior fragment-containing capabilities, etc.), ballistic ceramic-glass like fused-silica remains an important constituent material in a majority of transparent impact-resistant structures (e.g. windshields and windows of military vehicles, portholes in ships, ground vehicles and spacecraft) used today. Among the main reasons for the wide-scale use of glass, the following three are most frequently cited: (i) glass-structure fabrication technologies enable the production of curved, large surface-area, transparent structures with thickness approaching several inches; (ii) relatively low material and manufacturing costs; and (iii) compositional modifications, chemical strengthening, and controlled crystallization have been demonstrated to be capable of significantly improving the ballistic properties of glass. In the present work, the potential of high-pressure devitrification and densification of fused-silica as a ballistic-resistance-enhancement mechanism is investigated computationally. In the first part of the present work, all-atom molecular-level computations are carried out to infer the dynamic response and material microstructure/topology changes of fused silica subjected to ballistic impact by a nanometer-sized hard projectile. The analysis was focused on the investigation of specific aspects of the dynamic response and of the microstructural changes such as the deformation of highly sheared and densified regions, and the conversion of amorphous fused silica to SiO2 crystalline allotropic modifications (in particular, alpha-quartz and stishovite). The microstructural changes in question were determined by carrying out a post-processing atom-coordination procedure. This procedure suggested the formation of high-density stishovite (and

  2. Fuse Modeling for Reliability Study of Power Electronics Circuits

    DEFF Research Database (Denmark)

    Bahman, Amir Sajjad; Iannuzzo, Francesco; Blaabjerg, Frede

    2017-01-01

    This paper describes a comprehensive modeling approach on reliability of fuses used in power electronic circuits. When fuses are subjected to current pulses, cyclic temperature stress is introduced to the fuse element and will wear out the component. Furthermore, the fuse may be used in a large...

  3. Fuse Modeling for Reliability Study of Power Electronics Circuits

    DEFF Research Database (Denmark)

    Bahman, Amir Sajjad; Iannuzzo, Francesco; Blaabjerg, Frede

    2017-01-01

    This paper describes a comprehensive modeling approach on reliability of fuses used in power electronic circuits. When fuses are subjected to current pulses, cyclic temperature stress is introduced to the fuse element and will wear out the component. Furthermore, the fuse may be used in a large...

  4. Estimating Quartz Reserves Using Compositional Kriging

    Directory of Open Access Journals (Sweden)

    J. Taboada

    2013-01-01

    Full Text Available The aim of this study was to determine spatial distribution and volume of four commercial quartz grades, namely, silicon metal, ferrosilicon, aggregate, and kaolin (depending on content in impurities in a quartz seam. The chemical and mineralogical composition of the reserves in the seam were determined from samples collected from outcrops, blasting operations, and exploratory drilling, and compositional kriging was used to calculate the volume and distribution of the reserves. A more accurate knowledge of the deposit ensures better mine planning, leading to higher profitability and an improved relationship with the environment.

  5. Wafer-fused semiconductor radiation detector

    Science.gov (United States)

    Lee, Edwin Y.; James, Ralph B.

    2002-01-01

    Wafer-fused semiconductor radiation detector useful for gamma-ray and x-ray spectrometers and imaging systems. The detector is fabricated using wafer fusion to insert an electrically conductive grid, typically comprising a metal, between two solid semiconductor pieces, one having a cathode (negative electrode) and the other having an anode (positive electrode). The wafer fused semiconductor radiation detector functions like the commonly used Frisch grid radiation detector, in which an electrically conductive grid is inserted in high vacuum between the cathode and the anode. The wafer-fused semiconductor radiation detector can be fabricated using the same or two different semiconductor materials of different sizes and of the same or different thicknesses; and it may utilize a wide range of metals, or other electrically conducting materials, to form the grid, to optimize the detector performance, without being constrained by structural dissimilarity of the individual parts. The wafer-fused detector is basically formed, for example, by etching spaced grooves across one end of one of two pieces of semiconductor materials, partially filling the grooves with a selected electrical conductor which forms a grid electrode, and then fusing the grooved end of the one semiconductor piece to an end of the other semiconductor piece with a cathode and an anode being formed on opposite ends of the semiconductor pieces.

  6. OPUS: the FUSE science data pipeline

    Science.gov (United States)

    Rose, James F.; Heller-Boyer, C.; Rose, M. A.; Swam, M.; Miller, W.; Kriss, G. A.; Oegerle, William R.

    1998-07-01

    This paper describes how the OPUS pipeline, currently used for processing science data from the Hubble Space Telescope (HST), was used as the backbone for developing the science data pipeline for a much smaller mission. The far ultraviolet spectroscopic explorer (FUSE) project selected OPUS for its data processing pipeline platform and selected the OPUS team at the STScI to write the FUSE pipeline applications. A total of 105 new modules were developed for the FUSE pipeline. The foundation of over 250 modules in the OPUS libraries allowed development to proceed quickly and with considerable confidence that the underlying functionality is reliable and robust. Each task represented roughly 90 percent reuse, and the project as a whole shows over 70 percent reuse of the existing OPUS system. Taking an existing system that is operational, and will be maintained for many years to come, was a key decision for the FUSE mission. Adding the extensive experience of the OPUS team to the task resulted in the development of a complete telemetry pipeline system within a matter of months. Reusable software has been the siren song of software engineering and object- oriented design for a decade or more. The development of inexpensive software systems by adapting existing code to new applications is as attractive as it has been elusive. The OPUS telemetry pipeline for the FUSE mission has proven to be a significant exception to that trend.

  7. Numerical and experimental analyses of the radiant heat flux produced by quartz heating systems

    Science.gov (United States)

    Turner, Travis L.; Ash, Robert L.

    1994-01-01

    A method is developed for predicting the radiant heat flux distribution produced by tungsten filament, tubular fused-quartz envelope heating systems with reflectors. The method is an application of Monte Carlo simulation, which takes the form of a random walk or ray tracing scheme. The method is applied to four systems of increasing complexity, including a single lamp without a reflector, a single lamp with a Hat reflector, a single lamp with a parabolic reflector, and up to six lamps in a six-lamp contoured-reflector heating unit. The application of the Monte Carlo method to the simulation of the thermal radiation generated by these systems is discussed. The procedures for numerical implementation are also presented. Experiments were conducted to study these quartz heating systems and to acquire measurements of the corresponding empirical heat flux distributions for correlation with analysis. The experiments were conducted such that several complicating factors could be isolated and studied sequentially. Comparisons of the experimental results with analysis are presented and discussed. Good agreement between the experimental and simulated results was obtained in all cases. This study shows that this method can be used to analyze very complicated quartz heating systems and can account for factors such as spectral properties, specular reflection from curved surfaces, source enhancement due to reflectors and/or adjacent sources, and interaction with a participating medium in a straightforward manner.

  8. Shocked quartz: A {sup 29}Si magic-angle-spinning nuclear magnetic resonance study

    Energy Technology Data Exchange (ETDEWEB)

    Fiske, P.S.; Nellis, W.J. [Lawrence Livermore National Lab., CA (United States). Physics and Space Technology Directorate; Xu, Z.; Stebbins, J.F. [Stanford Univ., CA (United States). Dept. of Geological and Environmental Sciences

    1998-11-01

    Quantitative {sup 29}Si NMR spectra of single-crystal {alpha}-quartz, shock compressed to 12--38 GPa and recovered, provide new information about the complex response of quartz to shock loading. Spectra from samples recovered from shock pressures of 12--20 GPa show a broadening of the {sup 29}Si NMR peak and the development of asymmetry toward lower NMR frequency (indicating an increase in the mean Si-O-Si intertetrahedral bond angle). NMR spectra of samples shock compressed above {approximately}25 GPa show increasing amounts of a separate amorphous phase of SiO{sub 2} with a mean Si-O-Si bond angle roughly 5{degree} narrower, and 10--15% denser, than fused SiO{sub 2}. Small amounts of crystalline material remain with a mean Si-O-Si bond angle up to 3{degree} larger than unshocked {alpha}-quartz. The recovery of dense glass indicates that post-shock temperatures were sufficiently low to also preserve stishovite, had any been created in the experiments. The paucity of stishovite or Si in an amorphous phase in the recovered samples suggests that the formation of stable, high-coordinated Si is kinetically hindered in shock compression experiments up to about 35--40 GPa, except in regions of high temperature, such as planar deformation features (PDFs), microfaults (pseudotachylites), or voids.

  9. Cochlear Implants

    Science.gov (United States)

    A cochlear implant is a small, complex electronic device that can help to provide a sense of sound. People who are ... of-hearing can get help from them. The implant consists of two parts. One part sits on ...

  10. Cochlear Implants

    Science.gov (United States)

    ... imaging (MRI) scans, to evaluate your inner ear anatomy. Cochlear implant surgery Cochlear implant surgery is usually performed as an outpatient procedure under general anesthesia. An incision is made behind the ear ...

  11. Endodontic and post-endodontic management of a fused molar

    Directory of Open Access Journals (Sweden)

    Ruchi Gupta

    2013-01-01

    Full Text Available Treatment of fused teeth needs special care and attention to the bizarre anatomy. This paper describes root canal treatment of a fused carious tooth presenting with apical periodontitis. It is a rare case of fusion of the mandibular second molar with a paramolar. There is no literature regarding placement of crown over endodontically treated fused teeth. In this case, the fused teeth were endodontically treated and restored by a porcelain fused to metal crown.

  12. Data Acquisition System for Quartz Crystal Microbalances

    Directory of Open Access Journals (Sweden)

    Kleber Romero Felizardo

    2006-02-01

    Full Text Available This work presents a data acquisition system used in a mass sensor: quartz crystal microbalance. This system reads the frequency of this sensor along the time and sends the collected data to the computer through a serial interface.

  13. Bubble Formation in Silicon-Quartz Interface

    OpenAIRE

    Kakimoto, K.; EGUCHI, M.; Ozoe, H.

    1997-01-01

    Bubble formation at an interface between silicon melt and a quartz crucible was studied by thermodynamical calculation and visualization of bubble formation using X-ray radiography. A phase diagram of silicon-oxygen (Si-O) system is also calculated from the reported thermodynamical data. Critical temperature and radius of bubble formation at the interface was discussed.

  14. Time-resolved luminescence from quartz

    NARCIS (Netherlands)

    Chithambo, M.L.; Ankjærgaard, C.; Pagonis, V.

    2016-01-01

    Time-resolved optical stimulation of luminescence has become established as a key method for measurement of optically stimulated luminescence from quartz, feldspar and α-Al2O3:C, all materials of interest in dosimetry. The aim of time-resolved optical stimulation is to separ

  15. A new method for synthesizing fluid inclusions in fused silica capillaries containing organic and inorganic material

    Science.gov (United States)

    Chou, I.-Ming; Song, Y.; Burruss, R.C.

    2008-01-01

    Considerable advances in our understanding of physicochemical properties of geological fluids and their roles in many geological processes have been achieved by the use of synthetic fluid inclusions. We have developed a new method to synthesize fluid inclusions containing organic and inorganic material in fused silica capillary tubing. We have used both round (0.3 mm OD and 0.05 or 0.1 mm ID) and square cross-section tubing (0.3 ?? 0.3 mm with 0.05 ?? 0.05 mm or 0.1 ?? 0.1 mm cavities). For microthermometric measurements in a USGS-type heating-cooling stage, sample capsules must be less than 25 mm in length. The square-sectioned capsules have the advantage of providing images without optical distortion. However, the maximum internal pressure (P; about 100 MPa at 22 ??C) and temperature (T; about 500 ??C) maintained by the square-sectioned capsules are less than those held by the round-sectioned capsules (about 300 MPa at room T, and T up to 650 ??C). The fused silica capsules can be applied to a wide range of problems of interest in fluid inclusion and hydrothermal research, such as creating standards for the calibration of thermocouples in heating-cooling stages and frequency shifts in Raman spectrometers. The fused silica capsules can also be used as containers for hydrothermal reactions, especially for organic samples, including individual hydrocarbons, crude oils, and gases, such as cracking of C18H38 between 350 and 400 ??C, isotopic exchanges between C18H38 and D2O and between C19D40 and H2O at similar temperatures. Results of these types of studies provide information on the kinetics of oil cracking and the changes of oil composition under thermal stress. When compared with synthesis of fluid inclusions formed by healing fractures in quartz or other minerals or by overgrowth of quartz at elevated P-T conditions, the new fused-silica method has the following advantages: (1) it is simple; (2) fluid inclusions without the presence of water can be formed; (3

  16. Fusing Facial Features for Face Recognition

    Directory of Open Access Journals (Sweden)

    Jamal Ahmad Dargham

    2012-06-01

    Full Text Available Face recognition is an important biometric method because of its potential applications in many fields, such as access control, surveillance, and human-computer interaction. In this paper, a face recognition system that fuses the outputs of three face recognition systems based on Gabor jets is presented. The first system uses the magnitude, the second uses the phase, and the third uses the phase-weighted magnitude of the jets. The jets are generated from facial landmarks selected using three selection methods. It was found out that fusing the facial features gives better recognition rate than either facial feature used individually regardless of the landmark selection method.

  17. Identifying well-bleached quartz using the different bleaching rates of quartz and feldspar luminescence signals

    DEFF Research Database (Denmark)

    Murray, A.S.; Thomsen, Kristina Jørkov; Masuda, N.;

    2012-01-01

    When dating older sedimentary deposits using quartz, there are no unambiguous methods for identifying the presence of incomplete bleaching. Current statistical analysis of dose distributions depends entirely on the assumption that incomplete bleaching and mixing are the main causes of any excess...... in relative bleaching rates of quartz optically stimulated luminescence (OSL) and feldspar luminescence stimulated at 50 °C by infrared light (IR50) and feldspar luminescence stimulated at 290 °C by infrared light after a stimulation at 50 °C (pIRIR290), and use recently deposited samples to determine...... that the large aliquot data are more likely to be correct. We conclude that a comparison of quartz and feldspar doses provides a useful independent method for identifying well-bleached quartz samples, and that it is unwise to apply statistical models to dose distributions without clear evidence for the physical...

  18. Dental Implant Surgery

    Science.gov (United States)

    ... here to find out more. Dental Implant Surgery Dental Implant Surgery Dental implant surgery is, of course, surgery, ... here to find out more. Dental Implant Surgery Dental Implant Surgery Dental implant surgery is, of course, surgery, ...

  19. Phase-referenced nonlinear spectroscopy of the α-quartz/water interface

    Energy Technology Data Exchange (ETDEWEB)

    Ohno, Paul E.; Saslow, Sarah A.; Wang, Hong-fei; Geiger, Franz M.; Eisenthal, Kenneth B.

    2016-12-13

    Probing the polarization of water molecules at charged interfaces by second harmonic generation (SHG) spectroscopy1 has been heretofore limited to isotropic solids. The signal intensity follows the interfacial potential, φo, according to I2ω ∝|χ(2)+ χ(3).φo|2, where I2ω is the SHG signal intensity oscillating at frequency 2ω, and χ(2) and χ(3) are the second- and third-order susceptibilities (χ(2) and χ(3)) of the interface probed. Here, we report the first phase-referenced SHG measurements under non-resonant conditions at the interface of z-cut α-quartz and water under conditions of dynamically changing ionic strength and bulk solution pH. Comparison to non-referenced SHG measurements obtained from the fused silica/water interface reveals that the χ(3).φo term takes the form of ( χ(3)±iχ(3)).φo, and that the interference between the χ(3).φo term and the bulk quartz χ(2) term depends on the rotation angle of α-quartz around the z-axis. This newly identified term, iχ(3).φo, which is out of phase from the surface terms, is of bulk origin. The experiment expands the scope of SHG spectroscopy to probe solid/liquid interfaces beyond amorphous and centrosymmetric materials towards crystal classes that lack centrosymmetry. The possibility of internally phase referencing the interfacial SHG response for the interfacial orientation analysis of species or materials in contact with α-quartz are discussed along with the implications for conditions of resonance enhancement.

  20. Fungal Systematics and Evolution: FUSE 1

    NARCIS (Netherlands)

    Crous, Pedro W; Schumacher, René K; Wingfield, Michael J; Lombard, Lorenzo; Giraldo, Alejandra; Christensen, Martha; Gardiennet, Alain; Nakashima, Chiharu; Pereira, Olinto L; Smith, Alexander J; Groenewald, Johannes Z

    2015-01-01

    Fungal Systematics and Evolution (FUSE) is introduced as a new series to expedite the publication of issues relating to the epitypification of formerly described species, report new sexual-asexual connections, the merging of sexual and asexual gen¬era following the end of dual nomenclature, and to

  1. Fused aromatic thienopyrazines: structure, properties and function

    KAUST Repository

    Mondal, Rajib

    2010-01-01

    Recent development of a fused aromatic thieno[3.4-b]pyrazine system and their application in optoelectronic devices are reviewed. Introduction of a fused aromatic unit followed by side chain engineering, dramatically enhanced the charge carrier mobility in thin film transistor devices and mobilities up to 0.2 cm2/Vs were achieved. The optoelectronic properties of these fused aromatic thienopyrazine polymers (Eg = 1.3 to 1.6 eV, HOMO = -4.9 to -5.2 V) were tuned by introduction of various fused aromatic rings within thienopyrazine. By balancing the fundamental properties of these polymers, both high charge carrier mobilities and moderate PCEs in solar cells were achieved. Further, effects of copolymerizing units are discussed. Low band gap semiconducting polymer (Eg ∼ 1 eV) with high field effect mobility (0.044 cm2/Vs) was obtained using cyclopentadithiophene as copolymerizing unit. Finally, a molecular design approach to enhance the absorption coefficients is discussed, which resulted in improved power conversion efficiency in bulk heterojunction solar cells. © 2010 The Royal Society of Chemistry.

  2. Renovating a Fusee Ceramique Barrel Vault

    NARCIS (Netherlands)

    Kamerling, M.W.

    2015-01-01

    This paper describes a proposal to renovate a Fusee Ceramique Barrel Vault with steel diagonals In 1956 two workshops, varying in height and span, were built in Wormerveer, The Netherlands. Both workshops were roofed with a concrete barrel vault with a thickness of 110 mm. The cylindrical vaults w

  3. 30 CFR 56.6502 - Safety fuse.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Safety fuse. 56.6502 Section 56.6502 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... initiation systems, igniter cord and connectors, or other nonelectric initiation systems shall be used...

  4. Demonstrating Earth Connections and Fuses Working Together

    Science.gov (United States)

    Harrison, Mark

    2017-01-01

    Earth wires and fuses work together in UK mains circuits to keep users safe from electric shocks and are taught in many school contexts. The subject can be quite abstract and difficult for pupils to grasp, and a simple but visually clear and direct demonstration is described which would be easy for most physics departments to build and which can…

  5. Millimeter And Submillimeter-Wave Integrated Circuits On Quartz

    Science.gov (United States)

    Mehdi, Imran; Mazed, Mohammad; Siegel, Peter; Smith, R. Peter

    1995-01-01

    Proposed Quartz substrate Upside-down Integrated Device (QUID) relies on UV-curable adhesive to bond semiconductor with quartz. Integrated circuits including planar GaAs Schottky diodes and passive circuit elements (such as bandpass filters) fabricated on quartz substrates. Circuits designed to operate as mixers in waveguide circuit at millimeter and submillimeter wavelengths. Integrated circuits mechanically more robust, larger, and easier to handle than planar Schottky diode chips. Quartz substrate more suitable for waveguide circuits than GaAs substrate.

  6. Emission polarization study on quartz and calcite.

    Science.gov (United States)

    Vincent, R. K.

    1972-01-01

    Calculation of the spectral emission polarization of quartz and calcite polished plates for observation angles of 20 and 70 deg by the substitution of complex index of refraction values for each mineral into Fresnel's equations. The emission polarization is shown to be quite wavelength-dependent, demonstrating that selected narrow or medium-width spectral bands exhibit a significantly higher percentage of polarization than a broad spectral band for these two minerals. Field measurements with a broadband infrared radiometer yield polarizations on the order of 2% for a coarse-grained granite rock and beach sand (both quartz-rich). This implies that a more sensitive detector with a selected medium-width filter may be capable of measuring emission polarization accurately enough to make this parameter useful as a remote sensing tool for discrimination among rocks on the basis of texture.

  7. Axiomatic Design of Micro Quartz Rate Sensor

    Institute of Scientific and Technical Information of China (English)

    SHI Yang-he; ZHANG Hong-hai; LIU Sheng

    2007-01-01

    Quartz rate sensors (QRS) made out of one single piece of quartz crystal are inertial devices which can be used for general rate control, stabilization, automotive and aerospace/defense markets,etc. The mechanical design of the QRS has been investigated based on axiomatic design. The axiomatic design matrix of the mechanical structure of Coriolis Vibratory Gyroscopes (CVG) has been proposed. The mechanical function of QRS is divided into three Function Requirements ( FR ) , i. e. , FR1 is the drive mode, FR2 is the sense mode, FR3 is a coupled connection where the Coriolis force can couple the two modes with a term proportional to the rotational rate. A new QRS which is easy to be fabricated has been put forward. Furthermore, the new QRS indicated that the axiomatic design is a help to functional design of products.

  8. The CMS forward calorimeter with quartz fibres

    CERN Multimedia

    Laurent Guiraud

    1999-01-01

    Part of the forward hadron calorimeter for the CMS experiment at the LHC is seen here. The calorimeter will be placed at the ends of the experiment barrel to measure the energy of particles produced in the 14 TeV proton-proton collisions. In consists of an iron absorber and specially designed radiation-hard quartz so that it survives the high radiation levels produced by collisions.

  9. THE FRICTION OF QUARTZ IN HIGH VACUUM

    Science.gov (United States)

    the effects of surface cleanliness . Ultra-high vacuums (to 10 to the minus 10th power torr) and high temperatures (to 350 deg C) were combined with...chemical cleaning and careful handling techniques to produce the maximum surface cleanliness . The coefficient of static friction under varying...on 30-40 mesh glass balls. The coefficient of friction of smooth quartz was found to vary from 0.1 to 1.0 depending on the surface cleanliness . The

  10. Implantable Microimagers

    Directory of Open Access Journals (Sweden)

    Jun Ohta

    2008-05-01

    Full Text Available Implantable devices such as cardiac pacemakers, drug-delivery systems, and defibrillators have had a tremendous impact on the quality of live for many disabled people. To date, many devices have been developed for implantation into various parts of the human body. In this paper, we focus on devices implanted in the head. In particular, we describe the technologies necessary to create implantable microimagers. Design, fabrication, and implementation issues are discussed vis-à-vis two examples of implantable microimagers; the retinal prosthesis and in vivo neuro-microimager. Testing of these devices in animals verify the use of the microimagers in the implanted state. We believe that further advancement of these devices will lead to the development of a new method for medical and scientific applications.

  11. Force chain forming quartz in an ultramylonite

    Science.gov (United States)

    Kilian, Rüdiger; Morales, Luiz F. G.; Peters, Max

    2014-05-01

    Polymineralic ultramylonites often show microstructures indicative of grain size sensitive creep with dissolution precipitation or diffusion accommodated grain boundary sliding. Typically phases show an anticorrelated distribution, the grain size is small and a crystallographic preferred orientation is absent. The latter observation is usually thought to originate from rigid body rotation of grains because flow dominated by diffusion creep operates at differential stresses, which are too low to activate crystal-plastic mechanisms. Here, we present quartz texture measurements from a natural ultramylonite, deformed under upper amphibolite facies conditions from the Nordmannvik Nappe, Upper Allochton of the Norwegian Caledonides. The ultramylonite has a mean grain size crystal-plastic processes. Alternative texture forming processes (e.g. growth textures) are also discussed. The texture in the foliation parallel clusters is thought to be an inherited texture from lower strain stages in the ultramylonite, as it is mostly present in the least deformed parts of the ultramylonite. However, we suggest that the texture formed in the foliation oblique clusters is related to a dynamic formation of force chains between quartz grains, where differential stresses become high enough for plastic yielding. The presence of force chains questions whether ultramylonites necessarily need to possess a linear viscous rheology, even if microstructures would indicate a diffusion creep mechanism. Pennacchioni G., Menegon L., Leiss B., Nestola F., Bromiley G., 2010: Development of crystallographic preferred orientation and microstructure during plastic deformation of natural coarse?grained quartz veins. Journal of Geophysical Research, Vol. 115, B12405

  12. A quartz-crystal-microbalance technique to investigate ion-induced erosion of fusion relevant surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Golczewski, A. [Institut fuer Allgemeine Physik, TU Wien, Wiedner Hauptstr. 8-10/E134, Association EURATOM-OAW, A-1040 Vienna (Austria)], E-mail: golczewski@iap.tuwien.ac.at; Dobes, K.; Wachter, G.; Schmid, M. [Institut fuer Allgemeine Physik, TU Wien, Wiedner Hauptstr. 8-10/E134, Association EURATOM-OAW, A-1040 Vienna (Austria); Aumayr, F. [Institut fuer Allgemeine Physik, TU Wien, Wiedner Hauptstr. 8-10/E134, Association EURATOM-OAW, A-1040 Vienna (Austria)], E-mail: aumayr@iap.tuwien.ac.at

    2009-02-15

    We describe a highly sensitive quartz-crystal-microbalance technique capable of determining erosion as well as implantation and retention rates for fusion relevant surfaces under ion bombardment. Total sputtering yields obtained with this technique for Ar ion impact on polycrystalline gold and tungsten surfaces are presented. The results compare well with existing experimental data as well as theoretical predictions and thus demonstrate the feasibility of the developed technique. Our setup is capable of detecting mass-changes as small as 10{sup -5} {mu}g/s, which corresponds to a removal of only 10{sup -4} W monolayers/s.

  13. Cryogenic surface distortion and hysteresis of a 50 CM diameter fused silica mirror cooled to 77 K

    Science.gov (United States)

    Young, Jeffrey A.; Howard, Steven D.; Augason, Gordon C.; Melugin, Ramsey K.

    1990-11-01

    A 50 cm diameter, lightweight, Amersil TO8E, fused-natural-quartz mirror with a single arch cross section was tested at the NASA/Ames Research Center Cryogenic Optics Test Facility to measure cryogenic distortion and hysteresis. The mirror was cooled to 77 K in four serial tests and the mirror figure was measured with a phase-measuring interferometer. On the basis of the repeatability of room temperature and cryogenic optical measurements, it was determined that the Single Arch Mirror had no measurable hysteresis and displayed repeatable cryogenic distortion. The Cryogenic Optics Test Facility, optical and thermal test methods, test results, and measurement accuracy are described.

  14. Textiles: Some technocal information and data VI: fusing

    CSIR Research Space (South Africa)

    Cawood, MP

    1980-09-01

    Full Text Available results. However, complaints of problem do occur particularly with the technology becoming more sophisticated. Fusing interlinings are coated with an adhesive which enables them to be fused under certain conditions of temperature, time and pressure onto...

  15. Luminescence sensitivity changes in quartz as a result of annealing

    DEFF Research Database (Denmark)

    Bøtter-Jensen, L.; Agersnap Larsen, N.; Mejdahl, V.

    1995-01-01

    Retrospective dosimetry using optically stimulated luminescence (OSL) on quartz extracted from (for example) bricks needs to account for strong OSL sensitivity changes that are known to occur depending on the previous thermal treatment of the sample. Non-heated quartz exhibits OSL orders of magni......Retrospective dosimetry using optically stimulated luminescence (OSL) on quartz extracted from (for example) bricks needs to account for strong OSL sensitivity changes that are known to occur depending on the previous thermal treatment of the sample. Non-heated quartz exhibits OSL orders...... of magnitude less per unit radiation than that for heated material. The reason these temperature-induced sensitivity changes occur in quartz is presently not well understood. This phenomenon is also seen in the related area of luminescence dating in which sedimentary quartz and quartz from heated...

  16. Effects of citric acid on separation of sillimanite from quartz

    Institute of Scientific and Technical Information of China (English)

    李晔; 雷东升; 鲁巍; 许时

    2002-01-01

    Quartz is the main gangue mineral of sillimanite. The results show that Al3+ and Fe3+ ion can activate the floatation of quartz and make the separation of quartz and sillimanite difficult when anion collector is used, and citric acid can inhibit the quartz activated by metallic ion and have slight influence on the sillimanite. X-ray photoelectronic energy spectrum analysis indicates that there are obvious electronic energy peaks on the surface of the quartz before citric acid is added into the ore pulp in presence of Al3+ and Fe3+, and after citric acid is added, the energy peak vanished. So citric acid can make Al3+ and Fe3+ on the surface of quartz solve and decrease the active points on the surface of quartz which can adsorb anion collector.

  17. Amorphization of α-Quartz under Irradiation

    Science.gov (United States)

    Douillard, L.; Duraud, J. P.

    1996-12-01

    The course of radiation induced damage produced in α-quartz by neutrons, ions, electrons or photons — commonly known as metamictization — has been re-analyzed by careful comparison of available experimental data. Specific interest was devoted to confront experimental metamict state features with current structural models. It comes out that the metamict state of irradiated quartz should exhibit some structural characteristics of the modulated structure proposed for vitreous silica. The metamictization process is consistent with a structural relaxation process of a highly defective quartz matrix. According to this new point defect analysis, structural relaxation should be triggered by a critical concentration of oxygen vacancy point defects likely to significantly lower the connectivity of the SiO{2} network. Various experimental results are interpreted by incorporating the influence of the SiO{2} crystalline polymorph and the influence of the nature of the irradiating particle to the point defect model. Nous avons étudié les modifications de propriétés et de structures de monocristaux de quartz α, consécutives à une irradiation sévère par des neutrons, des ions, des électrons ou des photons. Ce phénomène d'altération du quartz sous irradiation porte le nom de métamictisation. Notre travail exploite les recoupements de travaux antérieurs. Une attention particulière a été portée à la confrontation entre les données structurales expérimentales disponibles sur l'état métamicte du quartz et les modèles structuraux proposés. L'état métamicte du quartz présente ainsi les caractéristiques structurales du modèle de structure modulée, avancé pour décrire la structure de la silice thermique. Le mécanisme de métamictisation procéderait par relaxation de la matrice cristalline fortement endommagée. Ce phénomène de relaxation serait initié par l'apparition de concentration critique de défauts ponctuels de type lacunes d

  18. Multimodal Plasmonics in Fused Colloidal Networks

    CERN Document Server

    Teulle, Alexandre; Girard, C; Gurunatha, Kargal L; Li, Mei; Mann, Stephen; Dujardin, Erik

    2014-01-01

    Harnessing the optical properties of noble metals down to the nanometer-scale is a key step towards fast and low-dissipative information processing. At the 10-nm length scale, metal crystallinity and patterning as well as probing of surface plasmon (SP) properties must be controlled with a challenging high level of precision. Here, we demonstrate that ultimate lateral confinement and delocalization of SP modes are simultaneously achieved in extended self-assembled networks comprising linear chains of partially fused gold nanoparticles. The spectral and spatial distributions of the SP modes associated with the colloidal superstructures are evidenced by performing monochromated electron energy loss spectroscopy with a nanometer-sized electron probe. We prepare the metallic bead strings by electron beam-induced interparticle fusion of nanoparticle networks. The fused superstructures retain the native morphology and crystallinity but develop very low energy SP modes that are capable of supporting long range and s...

  19. Pressure evolution during HBC fuse operation

    Energy Technology Data Exchange (ETDEWEB)

    Rochette, D; Bussiere, W [Laboratoire Arc Electrique et Plasmas Thermiques (LAEPT)-CNRS UMR 6069, Universite Blaise Pascal, 24 Avenue des Landais, F 63177 Aubiere Cedex (France)

    2004-05-01

    The purpose of this paper is to describe the influence of the silica sand grains on pressure during the energy release in a high breaking capacity (HBC) fuse. During the HBC fuse operation, the pressure evolution is the result of two opposite trends: the pressure increase due to the interaction of the silica plasma with the surrounding granular sand, and the pressure decrease due to the propagation of the pressure waves toward the porous medium. Due to the complex phenomena occurring during the current extinction by a fuse, two kinds of pressure are distinguished: the pressure inside the silica plasma and the pressure in the silica sand. From the simulations we show that the Forchheimer flow resistance is stronger than the Darcy flow resistance once the electric power is over 30% of the maximum value. A comparison of the calculated and measured pressures is made at various positions from the fuse element axis. Two different pressures are obtained experimentally: the pressure P{sub SAND} exerted on the sand grains due to the plasma pressure, and the pressure P{sub GAS} of the gas flowing through the interstices of the silica sand. We show that the experimental and calculated trends are similar and they both depend on the electric power level and the silica sand mean granulometry. The maximum pressures are observed at the same time as the maximum electric power levels. The ratio P{sub SAND}/P{sub GAS} is about 8 with P{sub GAS} values not exceeding 1.5 x 10{sup 5} Pa.

  20. Demonstrating Earth connections and fuses working together

    Science.gov (United States)

    Harrison, Mark

    2017-03-01

    Earth wires and fuses work together in UK mains circuits to keep users safe from electric shocks and are taught in many school contexts. The subject can be quite abstract and difficult for pupils to grasp, and a simple but visually clear and direct demonstration is described which would be easy for most physics departments to build and which can make the concepts much more immediately understandable.

  1. Optimization of the hybrid bilayer membrane method for immobilization of avidin on quartz crystal microbalance.

    Science.gov (United States)

    Mun, Saem; Choi, Suk-Jung

    2009-04-15

    Hybrid bilayer membrane (HBM), comprising a lipid monolayer fused to a hydrophobic self-assembled monolayer (SAM), has a potential capability to provide a convenient tool for the preparation of functionalized sensor surfaces. In this work, the HBM approach was optimized for the preparation of avidin-containing quartz crystal microbalance (QCM) sensor chip which would be available for immobilization of biotinylated molecules. Lipid layer of HBM was composed of background lipid such as egg phosphatidyl choline and biotinylated lipid to which avidin was attached. Highest performance was obtained at 1:1 ratio of the biotinylated lipid and the background lipid, and sensitivity and stability of the resulting sensor chip was comparable to a sensor chip prepared by the conventional carbodiimide reaction. By utilizing the HBM method, construction of a stable avidin sensor chip was achieved within 40 min without any chemical steps. Thus the HBM method was proven to be a convenient and efficient way to immobilize avidin on sensor surfaces.

  2. Characterization of the QUartz Photon Intensifying Detector (QUPID) for use in Noble Liquid Detectors

    CERN Document Server

    Teymourian, A; Baudis, L; Beltrame, P; Brown, E; Cline, D; Ferella, A D; Fukasawa, A; Lam, C W; Lim, T; Lung, K; Meng, Y; Muramatsu, S; Pantic, E; Suyama, M; Wang, H; Arisaka, K

    2011-01-01

    Dark Matter and Double Beta Decay experiments require extremely low radioactivity within the detector materials. For this purpose, the University of California, Los Angeles and Hamamatsu Photonics have developed the QUartz Photon Intensifying Detector (QUPID), an ultra-low background photodetector based on the Hybrid Avalanche Photo Diode (HAPD) and entirely made of ultraclean synthetic fused silica. In this work we present the basic concept of the QUPID and the testing measurements on Qupids from the first production line. Screening of radioactivity at the Gator facility in the Laboratori Nazionali del Gran Sasso has shown that the QUPIDs safely fulfill the low radioactive contamination requirements for the next generation zero background experiments set by Monte Carlo simulations. The quantum efficiency of the QUPID at room temperature is > 30% at the xenon scintillation wavelength. At low temperatures, the QUPID shows a leakage current less than 1 nA and a global gain of 10^5. In these conditions, the phot...

  3. Re-osseointegration of loosened implant in a splinted fixed prosthesis

    African Journals Online (AJOL)

    2011-01-31

    Jan 31, 2011 ... implant occurred during the torque application to tighten the abutment during cementation, which was splinting along with the ... was explained to the patient that the mobile abutment ... manufacturer. ... Metal-fused ceramic prosthesis was fabricated for implant ... 50-150 µm) gives a strong sintered structure.

  4. Effects of Ti charge state, ion size and beam-induced compaction on the formation of Ag metal nanoparticles in fused silica

    Science.gov (United States)

    Magruder, R. H.; Meldrum, A.; Haglund, R. F.

    2015-04-01

    Metal nanoparticles formed by ion implantation in fused silica exhibit linear and nonlinear optical properties that can be altered by co-doping the silica substrate with transition-metal ions. For example, implantation of scandium in fused silica creates a directional optical dichroism due to the different spatial distribution of silver nanoparticles subsequently formed by Ag ion implantation. In this paper, we show that implantation of titanium ions alters the short- and intermediate-range order in the silica and thereby alters the diffusion and nucleation processes that lead to formation of silver nanoparticles. In particular, the dichroic response observed for Ag nanoparticles in Sc-implanted silica is, with one exception, in Ti-implanted silica. Compaction of the silica due to the ion implantation process appears to be similar for both Sc and Ti implantations, based on the observed shift of the 1,124 cm-1 transverse-optical phonon mode in the infrared reflectance spectrum. However, differences in chemical reactivity, bond lengths and electronic structure of Sc and Ti produce changes in electronic structure and strain that are sensitively reflected in the reflectance spectra of the Ag nanoparticles. These differences lead to modifications in the size, shape and spatial distributions of the silver nanoparticles and offer a powerful means of controlling their optical properties.

  5. AEROSOL FILTRATION USING QUARTZ SAND FILTER

    Directory of Open Access Journals (Sweden)

    Abbas H. Sulaymon

    2012-01-01

    Full Text Available The cement industry is the major source of cement dust which contains heavy metals like nickel, cobalt, lead, chromium, arsenic and hazardous substances like dioxins and furans. Exposure to these substances can cause health problems to human, animals and vegetation. A continuous pilot scale quartz sand filter was constructed and uses to study the effect of important design parameters (temperature, pre-loaded dust on the collector, diameter of the filter, bed depth, collector size and superficial velocity on its performance for cleaning of cement dust from air. Initial penetration and initial pressure drop (after 180s were measured and compared for different variables used in this study. The dirty bed was cleaned by means of reverse air flow when the pressure drop across the filter rises to 20 cmH2O. A macroscopic model describes the filter clogging was used to predict the effluent histories based on initial collection efficiency (η0exp which was determined from experimental data. A removal efficiency of more than 99% was obtained. The results show that 0.4% of cement dust still adheres on the quartz sand bed after 5 min of cleaning cycle. The presence of 0.4% of pre-load dust on the quartz sand filter enhanced the efficiency and low initial penetration, moderate initial pressure drop was obtained. At given Empty Bed Contact Time (EBCT, with different filter diameters 30 and 15 cm, a sharp decrease in initial penetration from 0.41-0.03 was obtained respectively. A nonlinear relationship between penetration and temperature was found. The initial penetration can be reduced by using smaller filter diameter, small collector size and collector with pre-load dust with 0.4%. The experiment that operates at a filter diameter of 15 cm and temperature of 25°C represent the minimum penetration among all the experiments.

  6. Kinetics of the coesite to quartz transformation

    Science.gov (United States)

    Mosenfelder, J.L.; Bohlen, S.R.

    1997-01-01

    The survival of coesite in ultrahigh-pressure (UHP) rocks has important implications for the exhumation of subducted crustal rocks. We have conducted experiments to study the mechanism and rate of the coesite ??? quartz transformation using polycrystalline coesite aggregates, fabricated by devitrifying silica glass cylinders containing 2850H/106 Si at 1000??C and 3.6 GPa for 24h. Conditions were adjusted following synthesis to transform the samples at 700-1000??C at pressures 190-410 MPa below the quartz-coesite equilibrium boundary. Reaction proceeds via grain-boundary nucleation and interface-controlled growth, with characteristic reaction textures remarkably similar to those seen in natural UHP rocks. We infer that the experimental reaction mechanism is identical to that in nature, a prerequisite for reliable extrapolation of the rate data. Growth rates obtained by direct measurement differ by up to two orders of magnitude from those estimated by fitting a rate equation to the transformation-time data. Fitting the rates to Turnbull's equation for growth therefore yields two distinct sets of parameters with similar activation energies (242 or 269 kJ/mol) but significantly different pre-exponential constants. Extrapolation based on either set of growth rates suggests that coesite should not be preserved on geologic time scales if it reaches the quartz stability field at temperatures above 375-400??C. The survival of coesite has previously been linked to its inclusion in strong phases, such as garnet, that can sustain a high internal pressure during decompression. Other factors that may play a crucial role in preservation are low fluid availability - possibly even less than that of our nominally "dry" experiments - and the development of transformation stress, which inhibits nucleation and growth. These issues are discussed in the context of our experiments as well as recent observations from natural rocks. ?? 1997 Elsevier Science B.V.

  7. Modelling and Analysis of Proximity Effect in IGBT Fuses

    DEFF Research Database (Denmark)

    Iov, Florin; Blaabjerg, Frede; Rasmussen, Henrik

    2005-01-01

    . Even with an active protection, a high power IGBT still has a risk of exhibiting a violent rupture in the case of a fault if e.g. IGBT fuses are not protecting it. By introducing fuses into voltage source converters a better protection of IGBT's can be achieved. However, skin and proximity effects...... affect the current distribution in a fuse due to the high frequency currents and thus a need for de-rating the fuse. This paper shows an analytical model for studying the proximity effect into a fuse. The results obtained using this model are compared with experiments....

  8. Calorimetric thermobarometry of experimentally shocked quartz

    Science.gov (United States)

    Ocker, Katherine D.; Gooding, James L.; Hoerz, Friedrich

    1994-01-01

    Structural damage in experimentally shock-metamorphosed, granular quartz is quantitatively measurable by differential scanning calorimetry (DSC). Shock-induced loss of crystallinity is witnessed by disappearance of the alpha/beta phase transformation and evolution of a broad endoenthalpic strain peak at 650-900 K. The strain-energy peak grows rapidly at less than 10 GPa but declines with increasing shock pressure; it approaches zero at 32 GPa where vitrification is extensive. Effects of grain size and post-shock thermal history must be better understood before calorimetric thermobarometry of naturally shocked samples becomes possible.

  9. Quartz resonator instabilities under cryogenic conditions.

    Science.gov (United States)

    Goryachev, Maxim; Galliou, Serge; Abbe, Philippe; Bourgeois, Pierre-Yves; Grop, Serge; Dubois, Benoit

    2012-01-01

    The phase noise of a quartz crystal resonator working at liquid helium temperatures is studied. Measurement methods and the device environment are explained. The phase noise is measured for different resonance modes, excitation levels, amount of operating time, device orientations in relation to the cryocooler vibration axis, and temperatures. Stability limits of a frequency source based on such devices are evaluated in the present measurement conditions. The sources of phase flicker and white noises are identified. Finally, the results are compared with previous works.

  10. Fused rock from Köfels, Tyrol

    Science.gov (United States)

    Milton, Daniel J.

    1964-01-01

    The vesicular glass from Köfels, Tyrol, contains grains of quartz that have been partially melted but not dissolved in the matrix glass. This phenomenon has been observed in similar glasses formed by friction along a thrust fault and by meteorite impact, but not in volcanic glasses. The explosion of a small nuclear device buried behind a steep slope produced a geologic structure that is a good small-scale model of that at Köfels. Impact of a large meteorite would have an effect analogous to that of a subsurface nuclear explosion and is the probable cause of the Köfels feature.

  11. Optical Performance Modeling of FUSE Telescope Mirror

    Science.gov (United States)

    Saha, Timo T.; Ohl, Raymond G.; Friedman, Scott D.; Moos, H. Warren

    2000-01-01

    We describe the Metrology Data Processor (METDAT), the Optical Surface Analysis Code (OSAC), and their application to the image evaluation of the Far Ultraviolet Spectroscopic Explorer (FUSE) mirrors. The FUSE instrument - designed and developed by the Johns Hopkins University and launched in June 1999 is an astrophysics satellite which provides high resolution spectra (lambda/Delta(lambda) = 20,000 - 25,000) in the wavelength region from 90.5 to 118.7 nm The FUSE instrument is comprised of four co-aligned, normal incidence, off-axis parabolic mirrors, four Rowland circle spectrograph channels with holographic gratings, and delay line microchannel plate detectors. The OSAC code provides a comprehensive analysis of optical system performance, including the effects of optical surface misalignments, low spatial frequency deformations described by discrete polynomial terms, mid- and high-spatial frequency deformations (surface roughness), and diffraction due to the finite size of the aperture. Both normal incidence (traditionally infrared, visible, and near ultraviolet mirror systems) and grazing incidence (x-ray mirror systems) systems can be analyzed. The code also properly accounts for reflectance losses on the mirror surfaces. Low frequency surface errors are described in OSAC by using Zernike polynomials for normal incidence mirrors and Legendre-Fourier polynomials for grazing incidence mirrors. The scatter analysis of the mirror is based on scalar scatter theory. The program accepts simple autocovariance (ACV) function models or power spectral density (PSD) models derived from mirror surface metrology data as input to the scatter calculation. The end product of the program is a user-defined pixel array containing the system Point Spread Function (PSF). The METDAT routine is used in conjunction with the OSAC program. This code reads in laboratory metrology data in a normalized format. The code then fits the data using Zernike polynomials for normal incidence

  12. Production of quartz plates for CMS-CASTOR Experiment

    CERN Document Server

    Adiguzel, Aytul; Ayhan, Aydin; Bakirci, Mustafa Numan; Basegmez, Suzan; Beaumont, Willem; Borras, Kerstin; Campbell, Alan; De Paula Carvalho, W; Çerçi, Salim; De Jesus Damiao, Dilson; Dogangün, O; Dumanoglu, Isa; d'Enterria, David; Erchov, Y; Eskut, Eda; Figueiredo, D; Girgis, Semiray; Göttlicher, P; Gouskos, Loukas; Gurpinar, Emine; Hos, Ilknur; Katkov, Igor; Katsas, Panagiotis; Khein, Lev; Knutsson, Albert; Kuznetsov, Andrey; Lebeau, Michel; Van Mechelen, Pierre; Muhl, Carsten; Musienko, Yuri; Ochesanu, Silvia; Onengüt, G; Onengut, G Jr; Ozdemir, Kadri; Panagiotou, Apostolos; Polatoz, A; Ripert, Marion; Shileev, K; Sogut, Kenan; Tiflov, B TaliV; Kayis-Topaksu, A; Uzun, Dilber

    2008-01-01

    Light transmission rate performance of $102$ irradiated quartz samples was measured to select the best quartz plates for CMS-CASTOR calorimeter. All the produced quartz plates were originally used in a previous CERN experiment, DELPHI. Three different doses of $^{60}$Co source were used with the collaboration of PSI (Paul Scherrer Institute, Villigen PSI, Switzerland.) to study the transmission rate performance of the quartz samples after irradiation for different incident light, ranging from $250$ to $700$ nm in $5$ nm increasing steps. All samples show different decrease in the rate with wavelength for different doses. Three different steps were followed before irradiation to find out the best way of cleaning the original DELPHI Cu/Cr tracks on the samples. Results of these measurements presented here correspond to the quartz plates that will be used in one hadronic sector of CASTOR calorimeter until end of 2008. For the full calorimeter new quartz plates will be installed. We also present the light transmi...

  13. Medicinal Chemistry Perspective of Fused Isoxazole Derivatives.

    Science.gov (United States)

    Barmade, Mahesh A; Murumkar, Prashant R; Sharma, Mayank Kumar; Yadav, Mange Ram

    2016-01-01

    Nitrogen containing heterocyclic rings with an oxygen atom is considered as one of the best combination in medicinal chemistry due to their diversified biological activities. Isoxazole, a five membered heterocyclic azole ring is found in naturally occuring ibetonic acid along with some of the marketed drugs such as valdecoxib, flucloxacillin, cloxacillin, dicloxacillin, and danazol. It is also significant for showing antipsychotic activity in risperidone and anticonvulsant activity in zonisamide, the marketed drugs. This review article covers research articles reported till date covering biological activity along with SAR of fused isoxazole derivatives.

  14. Semiautomatic MDF deburring tool. [Mild detonating fuse

    Energy Technology Data Exchange (ETDEWEB)

    Simonton, W.L.

    1976-03-31

    A device for semiautomatically deburring the ends of lengths of MDF (mild detonating fuse) was developed by the Automation Development group at Mound Laboratory. The device performs the deburring function by cutting a 0.002 in. x 0.002 in. chamfer on the MDF with small rotating blades. This air-operated, semiautomatic device provides improvement over the manual method of removing burrs by reduction in time and operator strain. A time study is underway to determine the time saved which is expected to be about 75 percent.

  15. Modeling by regression for laser cutting of quartz crystal

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Presents the theoretical models built by analysis of the mechanism of laser cutting of quartz crystal and re gression of test results for the laser cutting of quartz crystal, and comparative analysis of calculation errors for these models, and concludes with test results that these models comprehensively reflect the physical features of laser cutting of quartz crystal and satisfy the industrial production requirements, and they can be used to select right parameters for improvement of productivity and quality and saving of energy.

  16. Mineral resource of the month: cultured quartz crystal

    Science.gov (United States)

    ,

    2008-01-01

    The article presents information on cultured quartz crystals, a mineral used in mobile phones, computers, clocks and other devices controlled by digital circuits. Cultured quartz, which is synthetically produced in large pressurized vessels known as autoclaves, is useful in electronic circuits for precise filtration, frequency control and timing for consumer and military use. Several ingredients are used in producing cultured quartz, including seed crystals, lascas, a solution of sodium hydroxide or sodium carbonate, lithium salts and deionized water.

  17. Goserelin Implant

    Science.gov (United States)

    ... in men (blockage that causes difficulty urinating), or heart or liver disease.tell your doctor if you are pregnant or plan to become pregnant. Goserelin implant should not be used in pregnant women, except ...

  18. Trace elements in quartz shed light on sediment provenance

    Science.gov (United States)

    Ackerson, Michael R.; Tailby, Nicholas D.; Watson, E. Bruce

    2015-06-01

    Quartz is one of the most common minerals on the surface of the earth, and is a primary rock-forming mineral across the rock cycle. These two factors make quartz an obvious target for sediment provenance studies. Observations from experimental and natural samples demonstrate that the trace element content of quartz often reflects the conditions of quartz formation. When quartz is weathered from its primary crystallization setting (i.e., quartz from a granitoid) it can retain many chemical signatures of formation throughout the sedimentation processes. These geochemical signatures can be used to understand the primary source of individual quartz grains within a sediment. Here we present a case study from the Bega River catchment to demonstrate that quartz grains in sediments at the mouth of the Bega River are sourced from granitoids within the drainage basin. Data presented here also indicate that a portion of the beach sediment is also derived from either (i) sedimentary rocks within the basin or; (ii) mixing with sediments at the mouth of the river. The Bega River catchment was selected for this study because it is both small and has a well-constrained bedrock lithology, making it an ideal location to test the utility of this provenance technique. However, quartz trace element provenance has broad applications to modern and ancient sediments and can be used in lieu of, or in conjunction with, other provenance techniques to elucidate sediment transport through time.

  19. Contraceptive implants.

    Science.gov (United States)

    McDonald-Mosley, Raegan; Burke, Anne E

    2010-03-01

    Implantable contraception has been extensively used worldwide. Implants are one of the most effective and reversible methods of contraception available. These devices may be particularly appropriate for certain populations of women, including women who cannot use estrogen-containing contraception. Implants are safe for use by women with many chronic medical problems. The newest implant, Implanon (Organon International, Oss, The Netherlands), is the only device currently available in the United States and was approved in 2006. It is registered for 3 years of pregnancy prevention. Contraceptive implants have failure rates similar to tubal ligation, and yet they are readily reversible with a return to fertility within days of removal. Moreover, these contraceptive devices can be safely placed in the immediate postpartum period, ensuring good contraceptive coverage for women who may be at risk for an unintended pregnancy. Irregular bleeding is a common side effect for all progestin-only contraceptive implants. Preinsertion counseling should address possible side effects, and treatment may be offered to women who experience prolonged or frequent bleeding. Thieme Medical Publishers.

  20. Electrical field-induced faceting of etched features using plasma etching of fused silica

    Science.gov (United States)

    Huff, M.; Pedersen, M.

    2017-07-01

    This paper reports a previously unreported anomaly that occurs when attempting to perform deep, highly anisotropic etches into fused silica using an Inductively-Coupled Plasma (ICP) etch process. Specifically, it was observed that the top portion of the etched features exhibited a substantially different angle compared to the vertical sidewalls that would be expected in a typical highly anisotropic etch process. This anomaly has been termed as "faceting." A possible explanation of the mechanism that causes this effect and a method to eradicate it has been developed. Additionally, the method to eliminate the faceting is demonstrated. It is theorized that this faceting is a result of the interaction of the electro-potential electrical fields that surround the patterned nickel layers used as a hard mask and the electrical fields directing the high-energy ions from the plasma to the substrate surface. Based on this theory, an equation for calculating the minimum hard mask thickness required for a desired etch depth into fused silica to avoid faceting was derived. As validation, test samples were fabricated employing hard masks of thicknesses calculated based on the derived equation, and it was found that no faceting was observed on these samples, thereby demonstrating that the solution performed as predicted. Deep highly anisotropic etching of fused silica, as well as other forms of silicon dioxide, including crystalline quartz, using plasma etching, has an important application in the fabrication of several MEMS, NEMS, microelectronic, and photonic devices. Therefore, a method to eliminate faceting is an important development for the accurate control of the dimensions of deep and anisotropic etched features of these devices using ICP etch technology.

  1. Electrostatic Discharge Properties of Fused Silica Coatings

    Science.gov (United States)

    Andersen, Allen; Sim, Charles; Dennison, J. R.

    2012-10-01

    The electric field value at which electrostatic discharge (ESD) occurs was studied for thin coatings of fused silica (highly disordered SiO2/SiOx) on conductive substrates, such as those encountered as optical coatings and in Si microfabrication. The electrostatic breakdown field was determined using an increasing voltage, while monitoring the leakage current. A simple parallel-plate capacitor geometry was used, under medium vacuum and at temperatures down to ˜150 K using a liquid N2 reservoir. The breakdown field, pre-breakdown arcing and I-V curves for fused silica samples are compared for ˜60 nm and ˜80 μm thick, room and low temperature, and untreated and irradiated samples. Unlike typical I-V results for polymeric insulators, the thin film silica samples did not exhibit pre-breakdown arcing, displayed transitional resistivity after initial breakdown, and in many cases showed evidence of a second discontinuity in the I-V curves. This diversity of observed discharge phenomena is discussed in terms of breakdown modes and defect generation on a microscopic scale.

  2. Diagenetic Quartz Morphologies and Zeolite formation

    DEFF Research Database (Denmark)

    Kazerouni, Afsoon Moatari; Hansen, Rikke Weibel; Friis, Henrik

    ; the core of the zeolite crystals appears to have been more unstable than the rim and dissolved first.  Later the entire crystal dissolved and left an impression of the euhedral zeolite crystal in the microquartz coating.  Such openings in the microquartz coating are nucleation points for macroquartz.  Thus......, the precipitation of zeolite may later facilitate further quartz cementation, which might otherwise be retarded by the presence of disordered microquartz. The silica activity of pore fluids can influence zeolite precipitation.  Although zeolite formation is clearly related to volcanic ash, zeolite has also formed...... are abundant in some of associated shales; and 2) volcanic ash. The dissolution of biogenic silica may result in a rapid release of silica thereby promoting the formation of diagenetic opal/microquartz, but there may be a limited release of Al. A limited release of Al may result in precipitation of Si...

  3. Quartz tuning fork based microwave impedance microscopy

    Science.gov (United States)

    Cui, Yong-Tao; Ma, Eric Yue; Shen, Zhi-Xun

    2016-06-01

    Microwave impedance microscopy (MIM), a near-field microwave scanning probe technique, has become a powerful tool to characterize local electrical responses in solid state samples. We present the design of a new type of MIM sensor based on quartz tuning fork and electrochemically etched thin metal wires. Due to a higher aspect ratio tip and integration with tuning fork, such design achieves comparable MIM performance and enables easy self-sensing topography feedback in situations where the conventional optical feedback mechanism is not available, thus is complementary to microfabricated shielded stripline-type probes. The new design also enables stable differential mode MIM detection and multiple-frequency MIM measurements with a single sensor.

  4. Split Bregman method for large scale fused Lasso

    CERN Document Server

    Ye, Gui-Bo

    2010-01-01

    rdering of regression or classification coefficients occurs in many real-world applications. Fused Lasso exploits this ordering by explicitly regularizing the differences between neighboring coefficients through an $\\ell_1$ norm regularizer. However, due to nonseparability and nonsmoothness of the regularization term, solving the fused Lasso problem is computationally demanding. Existing solvers can only deal with problems of small or medium size, or a special case of the fused Lasso problem in which the predictor matrix is identity matrix. In this paper, we propose an iterative algorithm based on split Bregman method to solve a class of large-scale fused Lasso problems, including a generalized fused Lasso and a fused Lasso support vector classifier. We derive our algorithm using augmented Lagrangian method and prove its convergence properties. The performance of our method is tested on both artificial data and real-world applications including proteomic data from mass spectrometry and genomic data from array...

  5. Current advances in fused tetrathiafulvalene donor-acceptor systems.

    Science.gov (United States)

    Bergkamp, Jesse J; Decurtins, Silvio; Liu, Shi-Xia

    2015-02-21

    Electron donor (D) and acceptor (A) systems have been studied extensively. Among them, fused D-A systems have attracted much attention during the past decades. Herein, we will present the evolution of tetrathiafulvalene (TTF) fused D-A systems and their potential applications in areas such as solar cells, OFETs, molecular wires and optoelectronics just to name a few. The synthesis and electrochemical, photophysical and intrinsic properties of fused D-A systems will be described as well.

  6. Quartz enhanced photoacoustic spectroscopy based trace gas sensors using different quartz tuning forks.

    Science.gov (United States)

    Ma, Yufei; Yu, Guang; Zhang, Jingbo; Yu, Xin; Sun, Rui; Tittel, Frank K

    2015-03-27

    A sensitive trace gas sensor platform based on quartz-enhanced photoacoustic spectroscopy (QEPAS) is reported. A 1.395 μm continuous wave (CW), distributed feedback pigtailed diode laser was used as the excitation source and H2O was selected as the target analyte. Two kinds of quartz tuning forks (QTFs) with a resonant frequency (f0) of 30.72 kHz and 38 kHz were employed for the first time as an acoustic wave transducer, respectively for QEPAS instead of a standard QTF with a f0 of 32.768 kHz. The QEPAS sensor performance using the three different QTFs was experimentally investigated and theoretically analyzed. A minimum detection limit of 5.9 ppmv and 4.3 ppmv was achieved for f0 of 32.768 kHz and 30.72 kHz, respectively.

  7. A new irradiated quartz for beta source calibration

    DEFF Research Database (Denmark)

    Hansen, Vicki; Murray, Andrew Sean; Buylaert, Jan-Pieter;

    2015-01-01

    laboratories have used the various different batches of Risø calibration quartz for the calibration of beta and X-ray sources, but these have been largely undescribed. Here we describe in detail the preparation and luminescence characteristics of a new quartz standard, based on a North Sea beach sand collected...

  8. Quartz exposure in agriculture: literature review and South African survey.

    NARCIS (Netherlands)

    Swanepoel, A.J.; Rees, D.; Renton, K.; Swanepoel, C.; Kromhout, H.; Gardiner, K.

    2010-01-01

    OBJECTIVES: To review the published literature on respirable quartz exposure and associated disease in agricultural related settings systematically and to describe personal respirable dust and quartz measurements collected on a sandy soil farm in the Free State province of South Africa. METHODS: The

  9. Thermal quenching of thermoluminescence in quartz samples of various origin

    Energy Technology Data Exchange (ETDEWEB)

    Subedi, B. [Aristotle University of Thessaloniki, Nuclear Physics Laboratory, 54124-Thessaloniki (Greece); Oniya, E. [Archaeometry Laboratory, Cultural and Educational Technology Institute (C.E.T.I.), R.C. ' Athena' , Tsimiski 58, 67100 Xanthi (Greece); Physics and Electronics Department, Adekunle Ajasin University, PMB 01, Akungba Akoko (Nigeria); Polymeris, G.S. [ISIK University, Physics Department, Faculty of Science and Arts, 34980-Sile, Istanbul (Turkey); Afouxenidis, D.; Tsirliganis, N.C. [Archaeometry Laboratory, Cultural and Educational Technology Institute (C.E.T.I.), R.C. ' Athena' , Tsimiski 58, 67100 Xanthi (Greece); Kitis, G., E-mail: gkitis@auth.g [Aristotle University of Thessaloniki, Nuclear Physics Laboratory, 54124-Thessaloniki (Greece)

    2011-03-15

    The effect of thermal quenching stands among the most important properties in the thermoluminescence (TL) of quartz on which many applications of TL are based. Since the quartz samples used in various applications are all of different origin it is useful to investigate whether the values of the thermal quenching parameters, i.e. the activation energy for thermal quenching W and a parameter C which describes the ratio of non-radiative to radiative luminescence transitions, evaluated mainly in specific quartz samples can be extrapolated to quartz samples of unknown origin as well as to quartz samples which are annealed at high temperatures. In the present work the TL glow curve of a series of un-annealed and annealed natural and synthetic quartz samples were studied as a function of the heating rate between 0.25 K/s and 16 K/s. Using an indirect fitting method it was found that the thermal quenching parameters W and C in most of the quartz samples are very similar to the values accepted in the literature. Furthermore, in some cases the thermal quenching parameters W and C are not the same for all TL glow-peaks in the same glow-curve. Finally, the strong external treatment of annealing the quartz samples at very high temperature can also influence at least one of the thermal quenching parameters.

  10. Recent developments of OSL techniques for dating quartz and feldspars

    DEFF Research Database (Denmark)

    Bøtter-Jensen, L.; Jungner, H.; Mejdahl, V.

    1993-01-01

    The construction of a unit for measuring optically stimulated luminescence from quartz and feldspar is described. The light sources used for stimulation are infrared diodes for feldspar and green light from a halogen lamp (obtained with a system of filters) for both quartz and feldspar. The unit ...

  11. Speciation and phase separation of water in quartz (A review ...

    African Journals Online (AJOL)

    Speciation and phase separation of water in quartz (A review) ... of quartz at temperatures in excess of 500 °C. leading to decomposition of the ... The nucleation is a first order phase transition of creating liquid nucleus within the vapour phase, ...

  12. Removal of Ozone by Carbon Nanotubes/Quartz Fiber Film.

    Science.gov (United States)

    Yang, Shen; Nie, Jingqi; Wei, Fei; Yang, Xudong

    2016-09-01

    Ozone is recognized as a harmful gaseous pollutant, which can lead to severe human health problems. In this study, carbon nanotubes (CNTs) were tested as a new approach for ozone removal. The CNTs/quartz fiber film was fabricated through growth of CNTs upon pure quartz fiber using chemical vapor deposition method. Ozone conversion efficiency of the CNTs/quartz fiber film was tested for 10 h and compared with that of quartz film, activated carbon (AC), and a potassium iodide (KI) solution under the same conditions. The pressure resistance of these materials under different airflow rates was also measured. The results showed that the CNTs/quartz fiber film had better ozone conversion efficiency but also higher pressure resistance than AC and the KI solution of the same weight. The ozone removal performance of the CNTs/quartz fiber film was comparable with AC at 20 times more weight. The CNTs played a dominant role in ozone removal by the CNTs/quartz fiber film. Its high ozone conversion efficiency, lightweight and free-standing properties make the CNTs/quartz fiber film applicable to ozone removal. Further investigation should be focused on reducing pressure resistance and studying the CNT mechanism for removing ozone.

  13. Analysis of Rare Earth Elements (REE) in vein quartz and quartz-sandstone host rock in the Zhelannoe high purity quartz deposit, Russia

    Science.gov (United States)

    Zemskova, Marina; Prokofiev, Vsevolod; Bychkov, Andrey

    2015-04-01

    The Zhelannoe high purity quartz deposit is located on the western slope of the Polar Urals. It is one of the largest deposits of vein quartz and rock crystal in Russia. Most of the mineralization is hosted within a single horizon of very firm quartz-sandstone, where plastic deformation did not occur almost entirely. All tectonic stress was released by the development of numerous thrust faults of different scales. Cavities formed during this process were later filled with quartz and rock crystal. In order to obtain more details on conditions under which mineralization took place, analysis of trace element contents in vein quartz and host rocks, and the micro-thermometric study of fluid inclusions in quartz have been carried out. The trace element composition of vein quartz and of the host rock has been determined by ICP-MS. The results have shown that concentrations of most of the 46 studied elements in quartz are two orders of magnitude lower than in chondrite, and more than three orders of magnitude lower than in the upper crust. Even though Pb and Li have the highest concentrations in quartz samples, levels are only nearly comparable in chondrite, and substantially lower in the upper crust. At the same time, negative anomalies of Pb and Li concentrations in the host rock may indicate the removal of these elements during vein quartz formation. Contents of most REEs are two orders of magnitude lower than in chondrite, and three orders of magnitude lower than in the host rock. Generally, the patterns of REE distribution in vein quartz and the host rock express a clear correlation; confirming the genetic link between vein quartz and quartz-sandstone host rock. However, the process of quartz recrystallization led to an intense decrease of REEs content, and of all other impurities, which consequently influenced industrial value of the Zhelannoe deposit. As a result of the micro-thermometric study of fluid inclusions in quartz, the following physical

  14. Understanding error generation in fused deposition modeling

    Science.gov (United States)

    Bochmann, Lennart; Bayley, Cindy; Helu, Moneer; Transchel, Robert; Wegener, Konrad; Dornfeld, David

    2015-03-01

    Additive manufacturing offers completely new possibilities for the manufacturing of parts. The advantages of flexibility and convenience of additive manufacturing have had a significant impact on many industries, and optimizing part quality is crucial for expanding its utilization. This research aims to determine the sources of imprecision in fused deposition modeling (FDM). Process errors in terms of surface quality, accuracy and precision are identified and quantified, and an error-budget approach is used to characterize errors of the machine tool. It was determined that accuracy and precision in the y direction (0.08-0.30 mm) are generally greater than in the x direction (0.12-0.62 mm) and the z direction (0.21-0.57 mm). Furthermore, accuracy and precision tend to decrease at increasing axis positions. The results of this work can be used to identify possible process improvements in the design and control of FDM technology.

  15. Laser Damage Precursors in Fused Silica

    Energy Technology Data Exchange (ETDEWEB)

    Miller, P; Suratwala, T; Bude, J; Laurence, T A; Shen, N; Steele, W A; Feit, M; Menapace, J; Wong, L

    2009-11-11

    There is a longstanding, and largely unexplained, correlation between the laser damage susceptibility of optical components and both the surface quality of the optics, and the presence of near surface fractures in an optic. In the present work, a combination of acid leaching, acid etching, and confocal time resolved photoluminescence (CTP) microscopy has been used to study laser damage initiation at indentation sites. The combination of localized polishing and variations in indentation loads allows one to isolate and characterize the laser damage susceptibility of densified, plastically flowed and fractured fused silica. The present results suggest that: (1) laser damage initiation and growth are strongly correlated with fracture surfaces, while densified and plastically flowed material is relatively benign, and (2) fracture events result in the formation of an electronically defective rich surface layer which promotes energy transfer from the optical beam to the glass matrix.

  16. Mid-IR fused fiber couplers

    Science.gov (United States)

    Stevens, G.; Woodbridge, T.

    2016-03-01

    We present results from our recent efforts on developing single-mode fused couplers in ZBLAN fibre. We have developed a custom fusion workstation for working with lower melting temperature fibres, such as ZBLAN and chalcogenide fibres. Our workstation uses a precisely controlled electrical heater designed to operate at temperatures between 100 - 250°C as our heat source. The heated region of the fibers was also placed in an inert atmosphere to avoid the formation of microcrystal inclusions during fusion. We firstly developed a process for pulling adiabatic tapers in 6/125 μm ZBLAN fibre. The tapers were measured actively during manufacture using a 2000 nm source. The process was automated so that the heater temperature and motor speed automatically adjusted to pull the taper at constant tension. This process was then further developed so that we could fuse and draw two parallel 6/125 μm ZBLAN fibres, forming a single-mode coupler. Low ratio couplers (1-10%) that could be used as power monitors were manufactured that had an excess loss of 0.76 dB. We have also manufactured 50/50 splitters and wavelength division multiplexers (WDMs). However, the excess loss of these devices was typically 2 - 3 dB. The increased losses were due to localised necking and surface defects forming as the tapers were pulled further to achieve a greater coupling ratio. Initial experiments with chalcogenide fibre have shown that our process can be readily adapted for chalcogenide fibres. A 5% coupler with 1.5 dB insertion loss was manufactured using commercial of the shelf (COTS) fibres.

  17. High Voltage Applications of Explosively Formed Fuses

    Science.gov (United States)

    Tasker, D. G.; Goforth, J. H.; Fowler, C. M.; Herrera, D. H.; King, J. C.; Lopez, E. A.; Martinez, E. C.; Oona, H.; Marsh, S. P.; Reinovsky, R. E.; Stokes, J.; Tabaka, L. J.; Torres, D. T.; Sena, F. C.; Kiuttu, G.; Degnan, J.

    2004-11-01

    At Los Alamos, we have primarily applied Explosively Formed Fuse (EFF) techniques to high current systems. In these systems, the EFF has interrupted currents from 19-25 MA, thus diverting the current to low inductance loads. The transferred current magnitude is determined by the ratio of storage inductance to load inductance and, with dynamic loads, the current has ranged from 12-20 MA. In a system with 18 MJ stored energy, the switch operates at a power of up to 6 TW. We are now investigating the use of the EFF technique to apply high voltages to high impedance loads in systems that are more compact. In these systems we are exploring circuits with EFF lengths from 43-100 cm, which have storage inductances large enough to apply 300-500 kV across high impedance loads. Experimental results and design considerations are presented. Using cylindrical EFF switches of 10 cm diameter and 43 cm length, currents of approximately 3 MA were interrupted producing ~200 kV. This indicates the switch had an effective resistance of ~100 mΩ where 150-200 mΩ was expected. To understand the lower performance, several parameters were studied including electrical conduction through the explosive products; current density; explosive initiation; insulator type and conductor thickness. The results show a number of interesting features, most notably that the primary mechanism of switch operation is mechanical and not electrical fusing of the conductor. Switches opening on a 1-10 μs time scale with resistances starting at 50 μΩ and increasing to perhaps 1 Ω now seem possible to construct using explosive charges as small as a few pounds.

  18. Cochlear Implant

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In this text, the authors recall the main principles and data ruling cochlear implants. Then, a first circle of technical equipment for assistance is presented. This circle includes: device setting (DS), Electrically evoked Auditory Brainstem Responses (EABR), Neural Response Telemetry (NRT), Stapedial Reflex (SR) and Electrodogram Acquisition (EA). This first cycle becomes more and more important as children are implanted younger and younger; the amount of data available with this assistance makes necessary the use of models (implicit or explicit) to handle this information. Consequently, this field is more open than ever.

  19. FUSE observations of the central star of Abell 78

    CERN Document Server

    Werner, K; Koesterke, L; Kruk, J W

    2002-01-01

    FUSE high resolution spectra of two PG1159 type central stars (K1-16 and NGC 7094) have revealed an unexpected iron deficiency of at least 1 or 2 dex (Miksa et al. 2002). Here we present early results of FUSE spectroscopy of the CSPN Abell 78. It is shown that iron is strongly deficient in this star, too.

  20. Intracavity quartz-enhanced photoacoustic sensor

    Energy Technology Data Exchange (ETDEWEB)

    Borri, S., E-mail: simone.borri@ino.it; Galli, I.; Mazzotti, D.; Giusfredi, G.; De Natale, P. [CNR-INO UOS Sesto Fiorentino and LENS, via Carrara 1, 50019 Sesto Fiorentino FI (Italy); Patimisco, P.; Scamarcio, G.; Spagnolo, V. [CNR-IFN UOS Bari and Dipartimento Interateneo di Fisica, Università degli Studi di Bari e Politecnico di Bari, via Amendola 173, 70126 Bari BA (Italy); Akikusa, N. [Development Bureau Laser Device R and D Group, Hamamatsu Photonics KK, Shizuoka 434-8601 (Japan); Yamanishi, M. [Central Research Laboratories, Hamamatsu Photonics KK, Shizuoka 434-8601 (Japan)

    2014-03-03

    We report on a spectroscopic technique named intracavity quartz-enhanced photoacoustic spectroscopy (I-QEPAS) employed for sensitive trace-gas detection in the mid-infrared spectral region. It is based on a combination of QEPAS with a buildup optical cavity. The sensor includes a distributed feedback quantum cascade laser emitting at 4.33 μm. We achieved a laser optical power buildup factor of ∼500, which corresponds to an intracavity laser power of ∼0.75 W. CO{sub 2} has been selected as the target molecule for the I-QEPAS demonstration. We achieved a detection sensitivity of 300 parts per trillion for 4 s integration time, corresponding to a noise equivalent absorption coefficient of 1.4 × 10{sup −8} cm{sup −1} and a normalized noise-equivalent absorption of 3.2 × 10{sup −10} W cm{sup −1} Hz{sup −1/2}.

  1. Identification of color development potential of quartz by Raman spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Alkmim, Danielle G.; Lameiras, Fernando S.; Almeida, Frederico O.T., E-mail: alkmia@yahoo.com.br, E-mail: fsl@cdtn.br [Centro e Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horionte, MG (Brazil)

    2013-07-01

    Colorless quartz is usually exposed to ionizing radiation (gamma rays or high energy electron beams) to acquire different colors for jewelry. Color development is due to the presence of traces of some elements such as aluminum, iron, hydrogen, lithium, or sodium. Most quartz crystals are extracted colorless from nature and it is necessary to separate those that can develop colors from those that cannot. Irradiation tests can be used to accomplish this separation, but they take a long time. Infrared signature of colorless quartz can also be used. However, infrared spectroscopy is quite expensive, especially when using portable devices. Raman spectroscopy is now available as an inexpensive and portable technique that could provide identification of the samples of colorless quartz still in the field, facilitating the prediction for their economic exploitation. In addition, Raman spectroscopy usually requires a minimum or no sample preparation. This paper presents an investigation of the feasibility of using Raman spectroscopy as a substitute for infrared spectroscopy to predict the potential for color development of quartz. A band at 3595 cm{sup -1} in the Raman shift spectrum was observed only along the c axis of a prasiolite excited by a high power 514 nm laser. This band was not observed in quartz samples that do not develop color after irradiation. Further studies are required to identify the potential for color development by Raman spectroscopy of other types of colorless quartz. (author)

  2. Thermal performance of back-up current-limiting fuses

    Energy Technology Data Exchange (ETDEWEB)

    Torres, E.; Mazon, A.J.; Fernandez, E.; Zamora, I. [Department of Electrical Engineering, University of the Basque Country (UPV/EHU), Alameda de Urquijo, s/n, Bilbao 48013, Bizkaia (Spain); Perez, J.C. [MESA - Schneider Electric, Gatica 48110 (Spain)

    2010-12-15

    The design and development of current-limiting power fuses requires considerable time and expense on testing to verify that the maximum temperature limits under the rated current established in international standards are not exceeded. This paper presents a new methodology that reproduces the thermal behaviour of high voltage current-limiting fuses under currents up to the rated value and so, it reduces the need for testing as prototypes, more similar to the final design, can be obtained. Firstly, the methodology solves the transient heating process of the fuse to obtain the values of the power dissipated and the heat transfer coefficient, corresponding to the steady state condition. Once these values have been calculated, the temperature distribution at the surface of the complete fuse is obtained. The validity of the method proposed has been verified by comparison of the numerical values calculated with those obtained by testing real fuses. (author)

  3. A spectroscopic method for determining thickness of quartz wave plate

    Institute of Scientific and Technical Information of China (English)

    Weiwei Feng; Lihuang Lin; Ligang Chen; Huafeng Zhu; Ruxin Li; Zhizhan Xu

    2006-01-01

    A spectroscopic method to determine thickness of quartz wave plate is presented. The method is based on chromatic polarization interferometry. With the polarization-resolved transmission spectrum (PRTS)curve, the phase retardation of quartz wave plate can be determined at a wide spectral range from 200 to2000 nm obviously. Through accurate judgment of extreme points of PRTS curve at long-wave band, the physical thickness of quartz wave plates can be obtained exactly. We give a measuring example and the error analysis. It is found that the measuring precision of thickness is mainly determined by the spectral resolution of spectrometer.

  4. Using a titanium-in-quartz geothermometer for crystallization temperature estimation of the Palaeoproterozoic Suursaari quartz porphyry

    Directory of Open Access Journals (Sweden)

    Kairi Ehrlich

    2012-11-01

    Full Text Available The Suursaari volcanic sequence represents volcanic activity related to Wiborg Batholith rapakivi intrusions in the southern part of the Fennoscandian Shield. The estimated pressure conditions for batholith granitic rocks are 1–5 kbar and crystallization temperatures range from 670 to 890 °C. To describe the temperature regime of the Suursaari volcanic system, a rock sample was taken from the Mäkiinpäällys Mountain outcrop and analysed with laser ablation inductively coupled plasma mass spectrometry. Sample spots were selected from quartz phenocrysts and groundmass. Quartz crystallization temperatures were calculated by the Ti-in-quartz method that takes into account rutile equilibrium and Ti activity in each phase. The calculated crystallization temperatures of the Suursaari quartz porphyry are in the range of 647–738 °C. The results show that the Suursaari quartz porphyry contains two generations of quartz which can be distinguished on the basis of crystallization temperatures: phenocrysts crystallized at higher and groundmass quartz at lower temperature.

  5. Fused silica challenges in sensitive space applications

    Science.gov (United States)

    Criddle, Josephine; Nürnberg, Frank; Sawyer, Robert; Bauer, Peter; Langner, Andreas; Schötz, Gerhard

    2016-07-01

    Space bound as well as earthbound spectroscopy of extra-terrestrial objects finds its challenge in light sources with low intensities. High transmission for every optical element along the light path requires optical materials with outstanding performance to enable the measurement of even a one-photon event. Using the Lunar Laser Ranging Project and the LIGO and VIRGO Gravitational Wave Detectors as examples, the influence of the optical properties of fused silica will be described. The Visible and Infrared Surveillance Telescope for Astronomy (VISTA) points out the material behavior in the NIR regime, where the chemical composition of optical materials changes the performance. Special fibers are often used in combination with optical elements as light guides to the spectroscopic application. In an extended spectral range between 350 and 2,200 nm Heraeus developed STU fiber preforms dedicated for broad band spectroscopy in astronomy. STU fibers in the broad spectral range as well as SSU fibers for UV transmission (180 - 400 nm) show also high gamma radiation resistance which allows space applications.

  6. Structure optimization and simulation analysis of the quartz micromachined gyroscope

    Science.gov (United States)

    Wu, Xuezhong; Wang, Haoxu; Xie, Liqiang; Dong, Peitao

    2014-03-01

    Structure optimization and simulation analysis of the quartz micromachined gyroscope are reported in this paper. The relationships between the structure parameters and the frequencies of work mode were analysed by finite element analysis. The structure parameters of the quartz micromachined gyroscope were optimized to reduce the difference between the frequencies of the drive mode and the sense mode. The simulation results were proved by testing the prototype gyroscope, which was fabricated by micro-electromechanical systems (MEMS) technology. Therefore, the frequencies of the drive mode and the sense mode can match each other by the structure optimization and simulation analysis of the quartz micromachined gyroscope, which is helpful in the design of the high sensitivity quartz micromachined gyroscope.

  7. Origin of organism-dependent biogenic silica quartz formation.

    Science.gov (United States)

    Sato, Kiminori

    2011-12-15

    Organism-dependent biogenic quartz formation in the steady-state environment is a phenomenon that can address the global environmental issues such as diagenetic evolution, biogeochemical cycling, and reservoir formation, but detailed studies have not been performed so far. Here, steady-state quartz formation is studied for amorphous silica of different biogenic origin on the basis of the recently established mechanistic model [Sato et al., J. Phys. Chem. C 2011, 115, 18131]. Amorphous silica originated from rice husks possesses angstrom-scale pores larger by 1.3 Å than those originated from diatom algae. The slight difference of pore size dramatically reduces activation energies of water diffusion by 78% and reactions of water molecules at pore surfaces by 47%, resulting in the reduction of activation energy of biogenic quartz formation by 64%. The present findings evidence that angstrom-scale pores intrinsically residing in the amorphous matrix are the organism-dependent origin of steady-state biogenic quartz formation.

  8. Degradation of glycine and alanine on irradiated quartz.

    Science.gov (United States)

    Pawlikowski, Maciej; Benko, Aleksandra; Wróbel, Tomasz P

    2013-04-01

    Recent researches suggest participation of minerals in the formation of life under primordial conditions. Among all of the minerals, quartz seems to be one of the most probable to take part in such processes. However, an external source of energy is needed, e.g. electric discharge. A device simulating the proposed conditions was designed and was used to simulate prebiotic conditions. Investigation of processes occurring during the stimulation of quartz with electric discharge was studied by means of Ultraviolet-visible (UV-VIS) spectroscopy, in order to monitor the generation kinetics of free radicals. Additionally, infrared spectroscopy was applied to identify chemical reaction products created in a solution of alanine or glycine, in the presence of quartz treated with electric discharge. Formation of increased amounts of free radicals, compared to experiments performed without quartz and/or amino acid, is reported, along with identification of possible degradation products of alanine. No synthetic reactions were observed.

  9. Quartz Fibers For Laser Therapy In Tissue Contact

    Science.gov (United States)

    Lenz, P.; Sabber, G.; Lambert, R.; Berger, F.

    1984-03-01

    Quartz fibers not protected by a gas stream and used in tissue contact can work virtually indefinitely due to "self cleaning" and "regeneration". Tissue lesions are similar to those obtained with conventional devices.

  10. Structure optimization and simulation analysis of the quartz micromachined gyroscope

    Directory of Open Access Journals (Sweden)

    Xuezhong Wu

    2014-02-01

    Full Text Available Structure optimization and simulation analysis of the quartz micromachined gyroscope are reported in this paper. The relationships between the structure parameters and the frequencies of work mode were analysed by finite element analysis. The structure parameters of the quartz micromachined gyroscope were optimized to reduce the difference between the frequencies of the drive mode and the sense mode. The simulation results were proved by testing the prototype gyroscope, which was fabricated by micro-electromechanical systems (MEMS technology. Therefore, the frequencies of the drive mode and the sense mode can match each other by the structure optimization and simulation analysis of the quartz micromachined gyroscope, which is helpful in the design of the high sensitivity quartz micromachined gyroscope.

  11. Low-temperature intracrystalline deformation microstructures in quartz

    NARCIS (Netherlands)

    Derez, Tine; Pennock, Gill; Drury, Martyn; Sintubin, Manuel

    A review of numerous genetic interpretations of the individual low-temperature intracrystalline deformation microstructures in quartz shows that there is no consensus concerning their formation mechanisms. Therefore, we introduce a new, purely descriptive terminology for the three categories of

  12. The Characteristics of the Shear-Vibrating Quartz Crystal Resonator

    Institute of Scientific and Technical Information of China (English)

    Wenjie Tian; Lingling Liu; Junling Lu; Fuxue Zhang

    2006-01-01

    According to the piezoelectric equation and the vibration theory of the quartz crystal, the relations between the vibrating frequency and structural parameters under the thickness-shear-vibration of AT-cut quartz crystal have been studied.The frequency conditions under which quartz crystal resonator formed stationary wave inside the electrode district and the transmission characteristics of wave outside the electrode district have also been discussed. A quartz crystal resonator was developed based on this analysis. The experiment showed that the force-sensing characteristics were independent of the fixation of the crystal edge. The detecting distinguish ability was up to 0.001 °, and the short-term frequency stability was up to 1.38x 10-10/min.

  13. Short Implants: New Horizon in Implant Dentistry.

    Science.gov (United States)

    Jain, Neha; Gulati, Manisha; Garg, Meenu; Pathak, Chetan

    2016-09-01

    The choice of implant length is an essential factor in deciding the survival rates of these implants and the overall success of the prosthesis. Placing an implant in the posterior part of the maxilla and mandible has always been very critical due to poor bone quality and quantity. Long implants can be placed in association with complex surgical procedures such as sinus lift and bone augmentation. These techniques are associated with higher cost, increased treatment time and greater morbidity. Hence, there is need for a less invasive treatment option in areas of poor bone quantity and quality. Data related to survival rates of short implants, their design and prosthetic considerations has been compiled and structured in this manuscript with emphasis on the indications, advantages of short implants and critical biomechanical factors to be taken into consideration when choosing to place them. Studies have shown that comparable success rates can be achieved with short implants as those with long implants by decreasing the lateral forces to the prosthesis, eliminating cantilevers, increasing implant surface area and improving implant to abutment connection. Short implants can be considered as an effective treatment alternative in resorbed ridges. Short implants can be considered as a viable treatment option in atrophic ridge cases in order to avoid complex surgical procedures required to place long implants. With improvement in the implant surface geometry and surface texture, there is an increase in the bone implant contact area which provides a good primary stability during osseo-integration.

  14. Influence of quartz particles on wear in vertical roller mills

    DEFF Research Database (Denmark)

    Jensen, Lucas R.D.; Friis, Henrik; Fundal, Erling;

    2010-01-01

    statistical planning, a total of 10 tests were arried out with two different limestones and one type of quartz sand. The size distributions were kept constant and only the mixing ratios were varied. It appears from the investigation that mixtures consisting of minerals with different grindabilities result...... in an increased concentration of abrasive particles in the grinding bed ðR2 > 0:99Þ. The present study shows that the quartz concentration in the grinding bed is determining the wear rate....

  15. Average life of oxygen vacancies of quartz in sediments

    Institute of Scientific and Technical Information of China (English)

    DIAO; Shaobo(刁少波); YE; Yuguang(业渝光)

    2002-01-01

    Average life of oxygen vacancies of quartz in sediments is estimated by using the ESR (electron spin resonance) signals of E( centers from the thermal activation technique. The experimental results show that the second-order kinetics equation is more applicable to the life estimation compared with the first order equation. The average life of oxygen vacancies of quartz from 4895 to 4908 deep sediments in the Tarim Basin is about 1018 a at 27℃.

  16. Interaction Between Graphene Oxide Nanoparticles and Quartz Sand.

    Science.gov (United States)

    Sotirelis, Nikolaos P; Chrysikopoulos, Constantinos V

    2015-11-17

    In this study, the influence of pH, ionic strength (IS), and temperature on graphene oxide (GO) nanoparticles attachment onto quartz sand were investigated. Batch experiments were conducted at three controlled temperatures (4, 12, and 25 °C) in solutions with different pH values (pH 4, 7, and 10), and ionic strengths (IS = 1.4, 6.4, and 21.4 mM), under static and dynamic conditions. The surface properties of GO nanoparticles and quartz sand were evaluated by electrophoretic mobility measurements. Derjaguin-Landau-Verwey-Overbeek (DLVO) potential energy profiles were constructed for the experimental conditions, using measured zeta potentials. The experimental results showed that GO nanoparticles were very stable under the experimental conditions. Both temperature and pH did not play a significant role in the attachment of GO nanoparticles onto quartz sand. In contrast, IS was shown to influence attachment. The attachment of GO particles onto quartz sand increased significantly with increasing IS. The experimental data were fitted nicely with a Freundlich isotherm, and the attachment kinetics were satisfactorily described with a pseudo-second-order model, which implies that the quartz sand exhibited substantial surface heterogeneity and that GO retention was governed by chemisorption. Furthermore, thermodynamic analysis revealed that the attachment process was nonspontaneous and endothermic, which may be associated with structural changes of the sand surfaces due to chemisorption. Therefore, secondary minimum interaction may not be the dominant mechanism for GO attachment onto the quartz sand under the experimental conditions.

  17. Basic characteristics of quartz crystal sensor with interdigitated electrodes

    Directory of Open Access Journals (Sweden)

    Hiroshi Muramatsu

    2016-03-01

    Full Text Available This paper describes basic characteristics of the quartz crystal sensor with interdigitated electrodes (IDE quartz crystal sensor which is for simultaneous monitoring of mass, viscosity, conductivity and dielectric changes of liquids or thin films. As the IDE quartz crystal sensor has three terminals for a pair of IDEs on the one side and a counter electrode on the other side, the resonance properties have been analyzed using the electrical equivalent circuit models and measured experimentally for all connecting types of electrode pairs. The IDE quartz crystal has shown clear resonance curves for calculating the resonance frequency and resonance resistance values as well as normal quartz crystal in the air and in contact with liquid. Small shifts in the resonance frequency and resonance resistance depending on the connecting types have been obtained and analyzed using the equivalent circuit models. We have found the integrated quartz crystal and IDE sensors could be monitored simultaneously by only one impedance analyzer. Finally, two types of measuring systems have been demonstrated for continuous measuring methods.

  18. Design and development of thin quartz glass WFXT polynomial mirror shells by direct polishing

    Science.gov (United States)

    Proserpio, L.; Campana, S.; Citterio, O.; Civitani, M.; Combrinck, H.; Conconi, P.; Cotroneo, V.; Freeman, R.; Langstrof, P.; Mattaini, E.; Morton, R.; Oberle, B.; Pareschi, G.; Parodi, G.; Pels, C.; Schenk, C.; Stock, R.; Tagliaferri, G.

    2010-07-01

    The Wide Field X-ray Telescope (WFXT) is a medium class mission for X-ray surveys of the sky with an unprecedented area and sensitivity. In order to meet the effective area requirement, the design of the optical system is based on very thin mirror shells, with thicknesses in the 1-2 mm range. In order to get the desired angular resolution (10 arcsec requirement, 5 arcsec goal) across the entire 1x1 degree FOV (Field Of View), the design of the optical system is based on nested modified grazing incidence Wolter-I mirrors realized with polynomial profiles, focal plane curvature and plate scale corrections. This design guarantees an increased angular resolution at large off-axis angle with respect to the normally used Wolter I configuration, making WFXT ideal for survey purposes. The WFXT X-ray Telescope Assembly is composed by three identical mirror modules of 78 nested shells each, with diameter up to 1.1 m. The epoxy replication process with SiC shells has already been proved to be a valuable technology to meet the angular resolution requirement of 10 arcsec. To further mature the telescope manufacturing technology and to achieve the goal of 5 arcsec, a deterministic direct polishing method is under investigation. The direct polishing method has already been used for past missions (as Einstein, Rosat, Chandra): the technological challenge now is to apply it for almost ten times thinner shells. Under investigation is quartz glass (fused silica), a well-known material with good thermo-mechanical and polishability characteristics that could meet our goal in terms of mass and stiffness, with significant cost and time saving with respect to SiC. Our approach is based on two main steps: first quartz glass tubes available on the market are grinded to conical profiles, and second the obtained shells are polished to the required polynomial profiles by CNC (Computer Numerical Control) polishing machine. In this paper, the first results of the direct grinding and polishing of

  19. Technical report on galvanic cells with fused-salt electrolytes

    Science.gov (United States)

    Cairns, E. J.; Crouthamel, C. E.; Fischer, A. K.; Foster, M. S.; Hesson, J. C.; Johnson, C. E.; Shimotake, H.; Tevebaugh, A. D.

    1969-01-01

    Technical report is presented on sodium and lithium cells using fused salt electrolytes. It includes a discussion of the thermally regenerative galvanic cell and the secondary bimetallic cell for storage of electricity.

  20. Fused Cast Alumina Refractory Products for Glass Tank Furnace

    Institute of Scientific and Technical Information of China (English)

    SHEN Keyin

    2006-01-01

    @@ 1 Subject and Scope The standard specifies the requirement, testing method, inspection rule and requirements for the labeling, packing, shipping and storing of the fused cast alumina refractory products for glass tanks.

  1. Quantification of residual stress from photonic signatures of fused silica

    Science.gov (United States)

    Cramer, K. Elliott; Hayward, Maurice; Yost, William T.

    2014-02-01

    A commercially available grey-field polariscope (GFP) instrument for photoelastic examination is used to assess impact damage inflicted upon the outer-most pane of Space Shuttle windows made from fused silica. A method and apparatus for calibration of the stress-optic coefficient using four-point bending is discussed. The results are validated on known material (acrylic) and are found to agree with literature values to within 6%. The calibration procedure is then applied to fused-silica specimens and the stress-optic coefficient is determined to be 2.43 ± 0.54 × 10-12 Pa-1. Fused silica specimens containing impacts artificially made at NASA's Hypervelocity Impact Technology Facility (HIT-F), to simulate damage typical during space flight, are examined. The damage sites are cored from fused silica window carcasses and examined with the GFP. The calibrated GFP measurements of residual stress patterns surrounding the damage sites are presented.

  2. Polymer Matrix Composites using Fused Deposition Modeling Technology Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Fused deposition modeling (FDM) is an additive manufacturing technology that allows fabrication of complex three-dimensional geometries layer-by-layer. The goal of...

  3. IGBT Fuses for Protection Against Explosion in Voltage Source Converters

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Iov, Florin; Rasmussen, H.

    2004-01-01

    The consequences of electrical faults can be severe; not only to the equipment, but also in the worse case, to people if safety principles are not observed. Every year new applications based on DC-link Voltage Source Converters are added and the demand for protection of power electronics increases...... regarding the high-power IGBT modules. Due to the fact that the power level increases more energy is stored in the DC-link and even with an active protection, a high-power IGBT still has a risk of case rupture (explode) when a circuit failure condition occurs. A possible solution is a protection...... of the converter with standard High Speed Fuses or High Speed IGBT fuses. It is discussed that protection can be achieved by introduction of IGBT fuse located in the DC-link. Experiments show that explosion can be avoided by use of High Speed Fuse protection and the added inductance of standard High Speed...

  4. Cochlear Implant

    Directory of Open Access Journals (Sweden)

    Mehrnaz Karimi

    1992-04-01

    Full Text Available People with profound hearing loss are not able to use some kinds of conventional amplifiers due to the nature of their loss . In these people, hearing sense is stimulated only when the auditory nerve is activated via electrical stimulation. This stimulation is possible through cochlear implant. In fact, for the deaf people who have good mental health and can not use surgical and medical treatment and also can not benefit from air and bone conduction hearing aids, this device is used if they have normal central auditory system. The basic parts of the device included: Microphone, speech processor, transmitter, stimulator and receiver, and electrode array.

  5. Synkinematic quartz cementation in partially open fractures in sandstones

    Science.gov (United States)

    Ukar, Estibalitz; Laubach, Stephen E.; Fall, Andras; Eichhubl, Peter

    2014-05-01

    Faults and networks of naturally open fractures can provide open conduits for fluid flow, and may play a significant role in hydrocarbon recovery, hydrogeology, and CO2 sequestration. However, sandstone fracture systems are commonly infilled, at least to some degree, by quartz cement, which can stiffen and occlude fractures. Such cement deposits can systematically reduce the overall permeability enhancement due to open fractures (by reducing open fracture length) and result in permeability anisotropies. Thus, it is important to identify the factors that control the precipitation of quartz in fractures in order to identify potential fluid conduits under the present-day stress field. In many sandstones, quartz nucleates syntaxially on quartz grain or cement substrate of the fracture wall, and extends between fracture walls only locally, forming pillars or bridges. Scanning electron microscope cathodoluminescence (SEM-CL) images reveal that the core of these bridges are made up of bands of broken and resealed cement containing wall-parallel fluid inclusion planes. The fluid inclusion-rich core is usually surrounded by a layer of inclusion-poor clear quartz that comprises the lateral cement. Such crack-seal textures indicate that this phase was precipitating while the fractures were actively opening (synkinematic growth). Rapid quartz accumulation is generally believed to require temperatures of 80°C or more. Fluid inclusion thermometry and Raman spectroscopy of two-phase aqueous fluid-inclusions trapped in crack-seal bands may be used to track the P-T-X evolution of pore fluids during fracture opening and crack-seal cementation of quartz. Quartz cement bridges across opening mode fractures in the Cretaceous Travis Peak Formation of the tectonically quiescent East Texas Basin indicate individual fractures opened over a 48 m.y. time span at rates of 16-23 µm/m.y. Similarly, the Upper Cretaceous Mesaverde Group in the Piceance Basin, Colorado contains fractures that

  6. Hernia Surgical Mesh Implants

    Science.gov (United States)

    ... Prosthetics Hernia Surgical Mesh Implants Hernia Surgical Mesh Implants Share Tweet Linkedin Pin it More sharing options ... majority of tissue used to produce these mesh implants are from a pig (porcine) or cow (bovine) ...

  7. Urogynecologic Surgical Mesh Implants

    Science.gov (United States)

    ... Prosthetics Urogynecologic Surgical Mesh Implants Urogynecologic Surgical Mesh Implants Share Tweet Linkedin Pin it More sharing options ... majority of tissue used to produce these mesh implants are from a pig (porcine) or cow (bovine). ...

  8. Degradation of implant materials

    CERN Document Server

    Eliaz, Noam

    2012-01-01

    This book surveys the degradation of implant materials, reviewing in detail such failure mechanisms as corrosion, fatigue and wear, along with monitoring techniques. Surveys common implant biomaterials, as well as procedures for implant retrieval and analysis.

  9. Effects of Vacuum of Fused Silica UV Damage

    Institute of Scientific and Technical Information of China (English)

    XU Shi-Zhen; LV Hai-Bing; YUAN Xiao-Dong; HUANG Jin; JIANG Xiao-Dong; WANG Hai-Jun; ZU Xiao-Tao; ZHENG Wan-Guo

    2008-01-01

    Damage points induced by 355 nm laser irradiation increase more quickly on the surface of fused silica in vacuum of about 10-3Pa than in atmospheric air at the same fluence.The larger concentration of point defects in vacuum is confirmed by photoluminescence intensity.X-ray photoelectron spectroscopy and infrared absorption indicate the formation of sub-stoichiometric sillca on the surface.The degradation mechanism of fused silica in vacuum is discussed.

  10. Fusing Manual and Machine Feedback in Biomedical Domain

    Science.gov (United States)

    2014-11-01

    Fusing manual and machine feedback in biomedical domain 1Jainisha Sankhavara, 1Fenny Thakrar, 2Shamayeeta Sarkar, 1Prasenjit Majumder 1DA-IICT...to obtain efficient biomedical document retrieval. We focused on fusing manual and machine feedback runs. Fusion run performs better and gives...retrieval of biomedical articles relevant for answering generic clini- cal questions about medical records. There are 30 topics provided, each

  11. ENDODONTIC MANAGEMENT OF FUSED MAXILLARY LATERAL INCISOR: A CASE REPORT

    Directory of Open Access Journals (Sweden)

    Wavdhane

    2014-11-01

    Full Text Available Fusion is a rare occurrence and its definitive diagnosis is of prime importance for successful root canal treatment. This case report discusses the endodontic and esthetic management of fused maxillary right lateral incisor. Root canal treatment was performed on the fused tooth. Nickel Chromium with ceramic crown was fabricated in the shape of lateral incisor. The patient remained asymptomatic and there was a reduction in the size of periapical radiolucency after six months.

  12. A coordinate-wise optimization algorithm for the Fused Lasso

    OpenAIRE

    Höfling, Holger; Binder, Harald; Schumacher, Martin

    2010-01-01

    L1 -penalized regression methods such as the Lasso (Tibshirani 1996) that achieve both variable selection and shrinkage have been very popular. An extension of this method is the Fused Lasso (Tibshirani and Wang 2007), which allows for the incorporation of external information into the model. In this article, we develop new and fast algorithms for solving the Fused Lasso which are based on coordinate-wise optimization. This class of algorithms has recently been applied very successfully to so...

  13. Global equation of state for a glassy material: Fused silica

    Energy Technology Data Exchange (ETDEWEB)

    Boettger, J.C.

    1994-09-01

    A new SESAME equation of state (EOS) for fused silica has been generated using the computer program GRIZZLY and will be added to the SESAME library as material number 7387. This new EOS provides better agreement with experimental data than was achieved by all previous SESAME EOSs for fused silica. Material number 7387 also constitutes the most realistic SESAME-type EOS generated for any glassy material thus far.

  14. Fusing Social Media and Mobile Analytics for Urban Sense Making

    Science.gov (United States)

    2017-05-09

    AFRL-AFOSR-JP-TR-2017-0037 Fusing Social Media and Mobile Analytics for Urban Sense-Making Archan Misra SINGAPORE MANAGEMENT UNIVERSITY Final Report...Final 3. DATES COVERED (From - To) 11 Dec 2013 to 10 Dec 2016 4. TITLE AND SUBTITLE Fusing Social Media and Mobile Analytics for Urban Sense-Making 5a...UNLIMITED: PB Public Release 13. SUPPLEMENTARY NOTES 14. ABSTRACT The proposed research was motivated by the observation that urban environments are

  15. Quartz concentration trends in metal and nonmetal mining.

    Science.gov (United States)

    Watts, Winthrop F; Huynh, Tran B; Ramachandran, Gurumurthy

    2012-01-01

    From 1974 through 2010, the Mine Safety and Health Administration (MSHA) collected nearly 147,000 respirable dust samples with a mass of at least 0.1 mg and a minimum of 1% quartz. These samples represent about 50% of all respirable dust compliance samples collected by MSHA. Analysis of these data shows that pockets of high concentrations and overexposure continue to exist. At underground mines, from 2005 to 2010, occupations with >20% of the samples exceeding the permissible exposure limit (PEL) and geometric mean quartz concentrations exceeding the ACGIH threshold limit value of 25 μg/m(3) included mucking, crusher operator, general laborer/utility, and front-end loader operator. During the same period, stone and rock saw operators and bagger and packers working at surface mines and mills also had >20% of the samples exceeding the PEL and geometric mean quartz concentrations >25 μg/m(3). Regardless of mine type or location, slow but steady improvement in exposure levels is seen in jobs involving crushing operations, which are widespread in the mining industry. Crusher operators are more likely to work in an enclosed area where it is easier to apply dust controls and air conditioning. A downward trend is also observed for vehicle equipment operators who drive load-haul-dumps, front-end loaders, trucks, and similar equipment. Crusher operators and vehicle equipment operators represent occupational categories that are widely sampled by MSHA inspectors. A small but statistically significant reduction in the overall mean respirable quartz dust and quartz concentrations from 1993 to 2010 was observed in most commodity groups. Variability from year to year and between commodities is high. Reduction in respirable quartz dust concentration does not necessarily correspond to a reduction in quartz concentration within the same commodity group. These trends are consistent with those reported in previous studies.

  16. Treated and untreated rock dust: Quartz content and physical characterization.

    Science.gov (United States)

    Soo, Jhy-Charm; Lee, Taekhee; Chisholm, William P; Farcas, Daniel; Schwegler-Berry, Diane; Harper, Martin

    2016-11-01

    Rock dusting is used to prevent secondary explosions in coal mines, but inhalation of rock dusts can be hazardous if the crystalline silica (e.g., quartz) content in the respirable fraction is high. The objective of this study is to assess the quartz content and physical characteristics of four selected rock dusts, consisting of limestone or marble in both treated (such as treatment with stearic acid or stearates) and untreated forms. Four selected rock dusts (an untreated and treated limestone and an untreated and treated marble) were aerosolized in an aerosol chamber. Respirable size-selective sampling was conducted along with particle size-segregated sampling using a Micro-Orifice Uniform Deposit Impactor. Fourier Transform Infrared spectroscopy and scanning electron microscopy with energy-dispersive X-ray (SEM-EDX) analyses were used to determine quartz mass and particle morphology, respectively. Quartz percentage in the respirable dust fraction of untreated and treated forms of the limestone dust was significantly higher than in bulk samples, but since the bulk percentage was low the enrichment factor would not have resulted in any major change to conclusions regarding the contribution of respirable rock dust to the overall airborne quartz concentration. The quartz percentage in the marble dust (untreated and treated) was very low and the respirable fractions showed no enrichment. The spectra from SEM-EDX analysis for all materials were predominantly from calcium carbonate, clay, and gypsum particles. No free quartz particles were observed. The four rock dusts used in this study are representative of those presented for use in rock dusting, but the conclusions may not be applicable to all available materials.

  17. Coating Characterization with the Quartz Crystal Microbalance

    Science.gov (United States)

    Sturdy, Lauren F.

    The quartz crystal microbalance is a sensitive tool that can be used to measure the mass, modulus and phase angle of films of appropriate thicknesses. It is can be applied to systems with very varied properties, from liquid to solid, and under many different conditions. In this thesis its capabilities have been used to study the properties of several different systems of relevance to the coatings, art conservation, and rubber communities, in the process of which new techniques and tools were developed to analyze data and improve QCM data collection and experimental design. Alkyd resins, which have been used in artists' paints since the twentieth century, are the subject of the first studies. Alkyds are oil-modified polyesters. These resins are of interest because of their relatively recent use in art and how little is known of the mechanical properties in the early stages of cure. The QCM was shown to be sensitive to the curing process, changes in temperature, and mass change due to exposure to water. Kinetic studies during the first days of curing showed that the curing process can be divided into three regions. The first is dominated by solvent evaporation. In the second, oxygen absorption dominates and the mechanical properties change rapidly. The final stage extends from when the film is touch dry after about a day to years and is characterized by mass loss and continued increases in the modulus. Studying the curing at different temperatures revealed that the reactions do proceed much more rapidly at higher temperatures and an overall energy of activation was calculated for the curing process. The mechanical properties of alkyd resins containing zinc oxide, a white pigment, were studied with the QCM, nanoindentation and dynamic mechanical analysis. These measurements showed increases in the modulus with the inclusion of zinc oxide, and the QCM data showed that the second region started at earlier times as the pigment concentration was increased. Linseed oil is

  18. Complications after cardiac implantable electronic device implantations

    DEFF Research Database (Denmark)

    Kirkfeldt, Rikke Esberg; Johansen, Jens Brock; Nohr, Ellen Aagaard;

    2014-01-01

    Complications after cardiac implantable electronic device (CIED) treatment, including permanent pacemakers (PMs), cardiac resynchronization therapy devices with defibrillators (CRT-Ds) or without (CRT-Ps), and implantable cardioverter defibrillators (ICDs), are associated with increased patient...

  19. Implant marketing: cost effective implant dentistry.

    Science.gov (United States)

    Wohrle, P S; Levin, R P

    1996-01-01

    The application of the KAL-Technique to the field of implant dentistry allows both patients and dental practices to benefit. It is an exciting advance that decreases frustration and stress in providing implant procedures and lowers overall costs. Professionals using the KAL-Technique report significant predictability in achieving passive framework fit. They are also lowering overall cost of implant cases, which increases the number of patients who can accept implant treatment. It has been well established that the more individuals in a practice that receive implants, the more referrals a practice will gain. This is because implant patients find tremendous advances in the quality of life, and do not hesitate to tell others who can take advantage of this opportunity. Implant dentistry is one of the fastest growing fields in dentistry today. While some other areas of dentistry begin to decline in volume and need, implant dentistry provides the opportunity to keep practices strong and to insure long-term success.

  20. Chemical etching of deformation sub-structures in quartz

    Science.gov (United States)

    Wegner, M. W.; Christie, J. M.

    1983-02-01

    Chemical etching of dislocations has been studied in natural and synthetic quartz single crystals, in deformed synthetic quartz and in naturally and experimentally deformed quartzites. The ability of different etchants to produce polished or preferentially etched surfaces on quartz is described. Dislocation etching was achieved on all crystal planes examined by using a saturated solution of ammonium bifluoride as the etchant. Appropriate etching times were determined for etching quartzites for grain size, subgrain boundaries, deformation lamellae, dislocations and twins. Growth and polished surfaces of synthetic single crystal quartz were similarly etched and dislocation etch pits, characteristic of various orientations were found. The use of ammonium bifluoride proved to be expecially advantageous for the basal plane, producing a polished surface with etch pits, suitable for dislocation etch pit counting. “Double” etch pits have been found on Dauphiné twin boundaries on the basal plane and the first order prism, using this etchant. Slip lines and deformation bands were suitably etched on deformed synthetic crystal surfaces for identification of the slip planes. Other acidic etchants have been explored and their application to the study of deformation structures in quartz crystals is discussed.

  1. Glycosylation of quinone-fused polythiophene for reagentless and label-free detection of E. coli.

    Science.gov (United States)

    Ma, Fen; Rehman, Abdul; Liu, Haiying; Zhang, Jingtuo; Zhu, Shilei; Zeng, Xiangqun

    2015-02-03

    In this report, a new polythiophene interface is fabricated containing fused quinone moieties which are then glycosylated to form a carbohydrate platform for bacterial detection. Very importantly, this interface can be used for label-free and reagentless detection, both by electrochemical and Quartz Crystal Microbalance (QCM) transducers and by using the direct pili-mannose binding as well as Concanavalin A (Con A) mediated lipopolysaccharides (LPS)-mannose binding. The conductive polymer's unique collective properties are very sensitive to very minor perturbations, which result in significant changes of electrical conductivity and providing amplified sensitivity and improved limits of detection (i.e., 25 cell/mL for electrochemical sensor and 50 cells/mL for QCM sensor), a widened logarithmic range of detection (i.e., 3-7 for pili-mannose binding and 2-8 for Con A mediated binding), high specificity and selectivity, and an extraordinary reliability by a mechanism of internal validation. With these analytical performances, the described biosensor is envisaged for being capable of differentiating Gram-negative bacterial strain and species, for many important applications.

  2. Fused Lasso Screening Rules via the Monotonicity of Subdifferentials.

    Science.gov (United States)

    Wang, Jie; Fan, Wei; Ye, Jieping

    2015-09-01

    Fused Lasso is a popular regression technique that encodes the smoothness of the data. It has been applied successfully to many applications with a smooth feature structure. However, the computational cost of the existing solvers for fused Lasso is prohibitive when the feature dimension is extremely large. In this paper, we propose novel screening rules that are able to quickly identity the adjacent features with the same coefficients. As a result, the number of variables to be estimated can be significantly reduced, leading to substantial savings in computational cost and memory usage. To the best of our knowledge, the proposed approach is the first attempt to develop screening methods for the fused Lasso problem with general data matrix. Our major contributions are: 1) we derive a new dual formulation of fused Lasso that comes with several desirable properties; 2) we show that the new dual formulation of fused Lasso is equivalent to that of the standard Lasso by two affine transformations; 3) we propose a novel framework for developing effective and efficient screening rules for fused Lasso via the monotonicity of the subdifferentials (FLAMS). Some appealing features of FLAMS are: 1) our methods are safe in the sense that the detected adjacent features are guaranteed to have the same coefficients; 2) the dataset needs to be scanned only once to run the screening, whose computational cost is negligible compared to that of solving the fused Lasso; (3) FLAMS is independent of the solvers and can be integrated with any existing solvers. We have evaluated the proposed FLAMS rules on both synthetic and real datasets. The experiments indicate that FLAMS is very effective in identifying the adjacent features with the same coefficients. The speedup gained by FLAMS can be orders of magnitude.

  3. Luminescence quartz dating of lime mortars. A first research approach.

    Science.gov (United States)

    Zacharias, N; Mauz, B; Michael, C T

    2002-01-01

    Lime mortars mixed with sand are well suited for connecting structural materials, like stones and bricks, due to the mechanical properties this material exhibits. Their extensive use in architectural and decorative works during the last 4000 years motivated the introduction of the 'Luminescence clock' for age determination of mortars. The same principles as for quartz optically stimulated luminescence (OSL) dating of sediments were applied for age estimation of a mortar fragment removed from a Byzantine church monument dated by archaeological means to 1050-1100 years ago (the first half of the 10th century). The OSL from the quartz was monitored under blue light stimulation and UV detection, using a single-aliquot-regenerative-dose protocol. The quartz-OSL dating of the mortar resulted in 870 +/- 230 a. TL polymineral fine grain dating was also performed on a brick fragment which was connected to the mortar, resulting in a TL age of 1095 +/- 190 a.

  4. Dosimetric properties of natural quartz grains extracted from fired materials

    DEFF Research Database (Denmark)

    Bluszcz, A.; Bøtter-Jensen, L.

    1995-01-01

    The paper describes an examination of the dosimetric properties of natural quartz grains extracted from ancient fired materials. Eleven samples of different origin were tested for their TL and GLSL (green light stimulated luminescence) sensitivities within the mGy dose range. Very promising results...... were obtained showing the possibility of measuring the doses of around 10 mGy with 1% precision using GLSL or TL and using the single aliquot technique for natural quartz as a dosimeter. The lowest detectable dose was estimated to be lower than 500 mu Gy. The results obtained indicate that natural...... quartz grains from selected materials could be used for the dosimetry of environmental gamma radiation for the purposes of paleodosimetric dating methods as well as for accident dosimetry....

  5. Water weakening in experimentally deformed milky quartz single crystals

    Science.gov (United States)

    Stunitz, H.; Thust, A.; Kilian, R.; Heilbronner, R.; Behrens, H.; Tarantola, A.; Fitz Gerald, J. D.

    2015-12-01

    Natural single crystals of quartz have been experimentally deformed in two orientations: (1) normal to one prism-plane, (2) In O+ orientation at temperatures of 900 and 1000°C, pressures of 1.0 and 1.5 GPa, and strain rates of ~1 x 10-6s-1. The starting material is milky quartz, consisting of dry quartz (H2O contents of recycling of H2O between FI´s, dislocation generation at very small fluid inclusions, incorporation of structurally bound H into dislocation cores, and release of H2O from dislocations back into FI´s during recovery. Cracking and crack healing play an important role in the recycling process and imply a close interrelationship between brittle and crystal plastic deformation. The H2O weakening by this process is of a disequilibrium nature and thus depends on the amount of H2O available.

  6. New multiphase equation of state for polycrystalline quartz

    Energy Technology Data Exchange (ETDEWEB)

    Boettger, J.C.; Lyon, S.P.

    1990-10-01

    We have generated separate equations of state (EOS's) for the alpha quartz, coesite, and stishovite phases of polycrystalline quartz (SiO{sub 2}) using the computer program GRIZZLY. We also modified the program GRIZZLY to combine two single-phase EOS's for a given material into a single two-phase EOS via minimization of the Gibbs free energy. This new version of GRIZZLY has been used to generate a three-phase SESAME type EOS for polycrystalline quartz using the three EOS's mentioned above. All four of the EOS's produced for SiO{sub 2} are now available on request. 17 refs., 4 figs., 1 tab.

  7. Periodic Error Compensation for Quartz MEMS Gyroscope Drift of INS

    Institute of Scientific and Technical Information of China (English)

    Xu Jianmao; Zhang Haipeng; Sun Junzhong

    2007-01-01

    In order to improve the navigation accuracy of an inertial navigation system (INS), composed of quartz gyroscopes, the existing real-time compensation methods for periodic errors in quartz gyroscope drift and the periodic error term relationship between sampled original data and smoothed data are reviewed. On the base of the results, a new compensation method called using former period characteristics to compensate latter smoothness data (UFCL for short) method is proposed considering the INS working characteristics. This new method uses the original data without smoothing to work out an error conversion formula at the INS initial alignment time and then compensate the smoothed data errors by way of the formula at the navigation time. Both theoretical analysis and experimental results demonstrate that this method is able to cut down on computational time and raise the accuracy which makes it a better real-time compensation approach for periodic error terms of quartz micro electronic mechanical system (MEMS) gyroscope's zero drift.

  8. Properties and behavior of quartz for the silicon process

    Energy Technology Data Exchange (ETDEWEB)

    Aasly, Kurt

    2008-07-01

    This PhD-thesis is a result of the study on important properties of quartz as a raw material for the metallurgical production of ferrosilicon and silicon metal. This includes defining mechanical properties important for the size reduction experienced during transport and storage and thermo-mechanical properties of quartz that is important for how the quartz reacts to the high temperatures experienced as it is charged on the furnace. Additionally, softening properties of quartz have been briefly discussed in some of the papers. Another important goal has been to test analytical and experimental methods for investigating the various properties. The investigations of important factors for the mechanical properties of ores and industrial minerals have been carried out as a literature study. The mining operation and transport from mine to smelter has been discussed and several factors that are significant for achieving best possible mechanical properties of the quartz have been identified. The most important factors are related to production in the mine and processing plant, which should be carefully planned to minimize the amount of blast-induced damage in the rock and thus achieve the best possible mechanical strength of the raw material. The amount of fines can be minimized by controlling the handling of the raw materials during the transport and storage. It is especially important to avoid high drops, both high single drops and accumulated height of all the drops in total. Investigations of the thermo-mechanical properties of quartz have been carried out by using different experimental and characterization methods. The petrographic investigations of the raw materials by polarized light microscopy have been important. Thermo-mechanical investigations have been high-temperature microthermometry and shock heating of quartz samples in an induction furnace with subsequent investigations of the heated material. The subsequent investigation included polarized- and

  9. Radioluminescence of synthetic quartz related to alkali ions

    Energy Technology Data Exchange (ETDEWEB)

    Martini, M., E-mail: m.martini@unimib.it [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); INFN-Sezione di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Fasoli, M. [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Galli, A. [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Istituto di Fotonica e Nanostrutture, IFN-CNR (Italy); Villa, I. [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Guibert, P. [IRAMAT-CRP2A (Institut de recherche sur les Archeomateriaux), UMR no. 5060, CNRS-Universite Bordeaux III, F-33607 Pessac (France)

    2012-04-15

    The radioluminescence (RL) of synthetic quartzes (GEMMA Quartz and Crystal Company) has been measured at room temperature. Some samples were treated by electrodiffusion ('sweeping') in order to change the concentrations of alkali ions, mainly Li{sup +} and Na{sup +}, which in quartz are known to be linked to Al ions, substitutional for Si ions. The RL emission spectra show evidence of a role of alkali ions in affecting some specific emissions. All the spectra could be analysed as composed of four bands in the blue and UV region. Specifically, the well known blue emission at around 470 nm was seen to be composed by two bands at 430 nm (2.86 eV) and at 485 nm (2.53 eV). Effects of irradiation, during the RL measurements, were clearly seen only in the 'Li swept in' sample, namely an increase in the 485 nm band intensity and a decrease in the 430 nm band one. The previously reported UV emission was detected at 355 nm (3.44 eV) in all the samples, being the most intense band in the 'swept out' sample. A further UV emission was detected at 315 nm (3.94 eV), more intense in untreated samples. Possible assignments of the detected emission bands are discussed in relation to the defects of quartz, specifically focusing on the Al centres that are most affected by sweeping procedures. - Highlights: Black-Right-Pointing-Pointer Contribution to the understanding of relationships between defects in quartz and luminescence emissions. Black-Right-Pointing-Pointer Role of charge compensators at substitutional Al sites in the optical properties of quartz. Black-Right-Pointing-Pointer Evidence of the double nature of the 'blue emission' (around 470 nm).

  10. 30 CFR 56.12037 - Fuses in high-potential circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fuses in high-potential circuits. 56.12037... § 56.12037 Fuses in high-potential circuits. Fuse tongs or hot line tools shall be used when fuses are removed or replaced in high-potential circuits....

  11. 30 CFR 57.12037 - Fuses in high-potential circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fuses in high-potential circuits. 57.12037... Electricity Surface and Underground § 57.12037 Fuses in high-potential circuits. Fuse tongs or hotline tools, shall be used when fuses are removed or replaced in high-potential circuits....

  12. Chiral habit selection on nanostructured epitaxial quartz films.

    Science.gov (United States)

    Carretero-Genevrier, Adrián; Gich, Martí; Picas, Laura; Sanchez, Clément; Rodriguez-Carvajal, Juan

    2015-01-01

    Understanding the crystallization of enantiomorphically pure systems can be relevant to diverse fields such as the study of the origins of life or the purification of racemates. Here we report on polycrystalline epitaxial thin films of quartz on Si substrates displaying two distinct types of chiral habits that never coexist in the same film. We combine Atomic Force Microscopy (AFM) analysis and computer-assisted crystallographic calculations to make a detailed study of these habits of quartz. By estimating the surface energies of the observed crystallites we argue that the films are enantiomorphically pure and we briefly outline a possible mechanism to explain the habit and chiral selection in this system.

  13. Carbothermal Reduction of Quartz in Different Gas Atmospheres

    Science.gov (United States)

    Li, Xiang; Zhang, Guangqing; Tang, Kai; Ostrovski, Oleg; Tronstad, Ragnar

    2015-01-01

    This article examines the influence of gas atmosphere on the synthesis of silicon carbide by carbothermal reduction of quartz. The quartz was crushed to Synthesis of silicon carbide in hydrogen was close to completion in 270 minutes at 1673 K (1400 °C), 140 minutes at 1773 K (1500 °C), and 70 minutes at 1873 K (1600 °C). Faster carbothermal reduction rate in hydrogen was attributed to the involvement of hydrogen in the reduction reactions by directly reducing silica and/or indirectly, by reacting with graphite to form methane as an intermediate reductant.

  14. ST Quartz Acoustic Wave Sensors with Sectional Guiding Layers

    Directory of Open Access Journals (Sweden)

    Glen McHale

    2008-07-01

    Full Text Available We report the effect of removing a section of guiding layer from the propagation paths of ST-quartz Love wave sensors; this offers the ease of fabrication of a polymer guiding layer whilst retaining the native surface of the quartz which may then be used for the attachment of a sensitizing layer. Data is presented for the rigid and viscous loading, which indicates a small reduction in mass sensitivity compared to a Love wave device. Biosensing capabilities of these discontinuous ‘sectional’ guiding layer devices are demonstrated using protein adsorption from solution.

  15. Quantification of Residual Stress from Photonic Signatures of Fused Silica

    Science.gov (United States)

    Cramer, K. Elliott; Hayward, Maurice; Yost, William E.

    2013-01-01

    A commercially available grey-field polariscope (GFP) instrument for photoelastic examination is used to assess impact damage inflicted upon the outer-most pane of Space Shuttle windows made from fused silica. A method and apparatus for calibration of the stress-optic coefficient using four-point bending is discussed. The results are validated on known material (acrylic) and are found to agree with literature values to within 6%. The calibration procedure is then applied to fused-silica specimens and the stress-optic coefficient is determined to be 2.43 +/- 0.54 x 10(exp -12)/Pa. Fused silica specimens containing impacts artificially made at NASA's Hypervelocity Impact Technology Facility (HIT-F), to simulate damage typical during space flight, are examined. The damage sites are cored from fused silica window carcasses and examined with the GFP. The calibrated GFP measurements of residual stress patterns surrounding the damage sites are presented. Keywords: Glass, fused silica, photoelasticity, residual stress

  16. Three-dimensional plotting and printing of an implant drilling guide: simplifying guided implant surgery.

    Science.gov (United States)

    Flügge, Tabea Viktoria; Nelson, Katja; Schmelzeisen, Rainer; Metzger, Marc Christian

    2013-08-01

    To present an efficient workflow for the production of implant drilling guides using virtual planning tools. For this purpose, laser surface scanning, cone beam computed tomography, computer-aided design and manufacturing, and 3-dimensional (3D) printing were combined. Intraoral optical impressions (iTero, Align Technologies, Santa Clara, CA) and digital 3D radiographs (cone beam computed tomography) were performed at the first consultation of 1 exemplary patient. With image processing techniques, the intraoral surface data, acquired using an intraoral scanner, and radiologic 3D data were fused. The virtual implant planning process (using virtual library teeth) and the in-office production of the implant drilling guide was performed after only 1 clinical consultation of the patient. Implant surgery with a computer-aided design and manufacturing produced implant drilling guide was performed during the second consultation. The production of a scan prosthesis and multiple preoperative consultations of the patient were unnecessary. The presented procedure offers another step in facilitating the production of drilling guides in dental implantology. Four main advantages are realized with this procedure. First, no additional scan prosthesis is needed. Second, data acquisition can be performed during the first consultation. Third, the virtual planning is directly transferred to the drilling guide without a loss of accuracy. Finally, the treatment cost and time required are reduced with this facilitated production process. Copyright © 2013 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

  17. Retrograde peri-implantitis

    Directory of Open Access Journals (Sweden)

    Mohamed Jumshad

    2010-01-01

    Full Text Available Retrograde peri-implantitis constitutes an important cause for implant failure. Retrograde peri-implantitis may sometimes prove difficult to identify and hence institution of early treatment may not be possible. This paper presents a report of four cases of (the implant placed developing to retrograde peri-implantitis. Three of these implants were successfully restored to their fully functional state while one was lost due to extensive damage. The paper highlights the importance of recognizing the etiopathogenic mechanisms, preoperative assessment, and a strong postoperative maintenance protocol to avoid retrograde peri-implant inflammation.

  18. [Bilateral cochlear implantation].

    Science.gov (United States)

    Kronenberg, Jona; Migirov, Lela; Taitelbaum-Swead, Rikey; Hildesheimer, Minka

    2010-06-01

    Cochlear implant surgery became the standard of care in hearing rehabilitation of patients with severe to profound sensorineural hearing loss. This procedure may alter the lives of children and adults enabling them to integrate with the hearing population. In the past, implantation was performed only in one ear, despite the fact that binaural hearing is superior to unilateral, especially in noisy conditions. Cochlear implantation may be performed sequentially or simultaneously. The "sensitive period" of time between hearing loss and implantation and between the two implantations, when performed sequentially, significantly influences the results. Shorter time spans between implantations improve the hearing results after implantation. Hearing success after implantation is highly dependent on the rehabilitation process which includes mapping, implant adjustments and hearing training. Bilateral cochlear implantation in children is recommended as the proposed procedure in spite of the additional financial burden.

  19. On Fusing Recursive Traversals of K-d Trees

    Energy Technology Data Exchange (ETDEWEB)

    Rajbhandari, Samyam; Kim, Jinsung; Krishnamoorthy, Sriram; Pouchet, Louis-Noel; Rastello, Fabrice; Harrison, Robert J.; Sadayappan, Ponnuswamy

    2016-03-17

    Loop fusion is a key program transformation for data locality optimization that is implemented in production compilers. But optimizing compilers currently cannot exploit fusion opportunities across a set of recursive tree traversal computations with producer-consumer relationships. In this paper, we develop a compile-time approach to dependence characterization and program transformation to enable fusion across recursively specified traversals over k-ary trees. We present the FuseT source-to-source code transformation framework to automatically generate fused composite recursive operators from an input program containing a sequence of primitive recursive operators. We use our framework to implement fused operators for MADNESS, Multiresolution Adaptive Numerical Environment for Scientific Simulation. We show that locality optimization through fusion can offer more than an order of magnitude performance improvement.

  20. Rapid prototyping of replica knee implants for in vitro testing

    Directory of Open Access Journals (Sweden)

    Verjans Mark

    2016-09-01

    Full Text Available The understanding of the complex biomechanics of the knee is a key for an optimal implant design. To easily investigate the influence of prosthetic designs on knee biomechanics a rapid prototyping workflow for knee implants has been developed and evaluated. Therefore, different manufacturing technologies and post-treatment methods have been examined and overall seven different replica knee implants were manufactured. For evaluation, the manufacturing properties such as surface accuracy and roughness were determined and kinematic behaviour was investigated in a novel knee testing rig. It was carried out that PolyJet-Modelling with a sanded surface resulted in changed kinematic patterns compared to a usual CoCr-UHMWPE implant. However, fused deposition modelling using ABS and subsequent surface smoothening with acetone vapor showed the lowest roughness of the manufactured implants and only minor kinematic differences. For this reason this method constitutes a promising approach towards an optimal implant design for improved patient-satisfaction and long lifetime of the implant. Finally the workflow is not only limited to the knee.

  1. Evaluation of trapping parameters of annealed natural quartz

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Rui [College of Resources, Environment & Tourism, Capital Normal University, 100048 Beijing (China); Shisanling Seismic Station, Institute of Earthquake Science, CEA, 102200 Beijing (China); Wei, Ming-Jian, E-mail: weimj@cnu.edu.cn [College of Resources, Environment & Tourism, Capital Normal University, 100048 Beijing (China); Song, Bo [College of Resources, Environment & Tourism, Capital Normal University, 100048 Beijing (China); Beijing Jing Yuan School, 100040 Beijing (China); Zhang, Yan [College of Resources, Environment & Tourism, Capital Normal University, 100048 Beijing (China); School of TaiPingqiao, Nan Lu of West Railway Station, 100073 Beijing (China); Zhao, Qiu-Yue [Key Laboratory of Tourism and Resources Environment in Universities of Shandong, Taishan University, 271000 Tai’an (China); Pan, Bao-Lin; Li, Teng-Fei [College of Resources, Environment & Tourism, Capital Normal University, 100048 Beijing (China)

    2016-05-15

    The thermoluminescence (TL) trapping parameters of annealed quartz have been investigated. The apparent TL peaks observed at temperatures of 133 °C, 211 °C, 266 °C and 405 °C, respectively, were named Peak I, Peak II, Peak III and Peak IV. The T{sub m} − T{sub stop} method is applied to investigate the number of peaks and their positions, and to obtain the trap distributions in the quartz. Peak shape (PS), Hoogenstraaten method (Various Heating Rates Method, VHR), and Computerized Glow Curve Deconvolution (CGCD) are used to evaluate the trapping parameters of the annealed quartz. The glow curve can be considered as a superposition of at least nine overlapping peaks. These peaks show up at 133 °C, 211 °C, 266 °C, 308 °C, 333 °C, 384 °C, 441 °C, 466 °C and 484 °C. The PS method can be only used in evaluating the parameters for Peaks I. The VHR method can be used in evaluating the trapping parameters for the first three peaks. CGCD method is complementary to obtaining parameters for the sub-peaks, and the thermal quenching correction with the Urbach’s method is necessary. The Urbach’s coefficient for the quartz is 30.03 kT{sub m}.

  2. Quartz-like Crystals Found in Planetary Disks

    Science.gov (United States)

    2008-01-01

    NASA's Spitzer Space Telescope has, for the first time, detected tiny quartz-like crystals sprinkled in young planetary systems. The crystals, which are types of silica minerals called cristobalite and tridymite, can be seen close-up in the black-and-white insets (cristobalite is on the left, and tridymite on the right). The main picture is an artist's concept of a young star and its swirling disk of planet-forming materials. Cristobalite and tridymite are thought to be two of many planet ingredients. On Earth, they are normally found as tiny crystals in volcanic lava flows and meteorites from space. These minerals are both related to quartz. For example, if you were to heat the familiar quartz crystals often sold as mystical tokens, the quartz would transform into cristobalite and tridymite. Because cristobalite and tridymite require rapid heating and cooling to form, astronomers say they were most likely generated by shock waves traveling through the planetary disks. The insets are Scanning Electron Microscope pictures courtesy of George Rossman of the California Institute of Technology, Pasadena, Calif.

  3. Application of quartz crystal microbalance technology in tribological investigation

    Science.gov (United States)

    The last fifteen years have seen considerable growth in the application of quartz crystal microbalance (QCM) to explore the tribological characteristics of materials. This article reviews some of the advances made in characterizing frictional properties of materials using the QCM, especially with di...

  4. Oxygen isotope equilibration systematics between quartz and water

    Energy Technology Data Exchange (ETDEWEB)

    Matthews, A. (Hebrew Univ., Jerusalem, Israel); Beckinsale, R.D.

    1979-01-01

    The /sup 18/O//sup 16/O fractionation accompanying the hydrothermal crystallization of quartz from silicic acid at 265/sup 0/ to 465/sup 0/C has been studied in order to assess the influences of (a) rate of quartz formation, (b) the nature of the reaction mechanism, and (c) temperature. At 360/sup 0/ and 465/sup 0/C, there are no indications of rate effects influencing isotope partitioning, but at 265/sup 0/C (where fractionation factors show an unusally large scatter) the evidence is inconclusive in this respect. All reaction appears to occur through solution-precipitation processes, with the intermediate phases, cristobalite and silica K, giving identical fractionation factors (within experimental errors) to quartz samples formed at the same temperature. The temperature-dependence of fractionation in the range 265/sup 0/ to 465/sup 0/C is given by the equation 10/sup 3/ ln ..cap alpha..(SiO/sub 2/--H/sub 2/O) = 3.05 x 10/sup 6/T/sup -2/ - 2.09. The data are in good agreement with other experimental calibrations of the quartz-water fractionation.

  5. Absorbed dose evaluations in retrospective dosimetry: Methodological developments using quartz

    DEFF Research Database (Denmark)

    Bailiff, I.K.; Bøtter-Jensen, L.; Correcher, V.

    2000-01-01

    Dose evaluation procedures based on luminescence techniques were applied to 50 quartz samples extracted from bricks that had been obtained from populated or partly populated settlements in Russia and Ukraine downwind of the Chernobyl NPP. Determinations of accrued dose in the range similar to 30...

  6. A new equation of state for α-quartz

    Science.gov (United States)

    Magyar, Rudolph; Carpenter, John

    2015-06-01

    Quartz (SiO2) is often used as an optically transparent window for visar signals in shock experiments and is itself an active component of the experiments. Therefore, the shock response of quartz is an important input that must be known to high fidelity for precise measurement of other materials. We describe on-going work to develop a wide-range equation of state table that includes multiple phases and incorporates the latest high quality experimental and density functional theory (DFT) calculations. The emphasis in this work is the proper description of α-quartz along its principal Hugoniot through Stishovite and liquid phases. While molecular dissociation occurs at high pressures and temperatures, we find that an additional dissociation model is unnecessary. Although SiO2 possesses a number of solid phases, we restrict our focus to α-quartz and Stishovite as these two provide the density change along the Hugoniot path. We compare the model to recently measured data on Sandia's Z-machine. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE.

  7. Equivalent dose determination using a quartz isothermal TL signal

    DEFF Research Database (Denmark)

    Vandenberghe, D.A.G.; Jain, Mayank; Murray, A.S.

    2009-01-01

    We report on further developments in the use of an isothermal thermoluminescence (ITL) signal for determining the equivalent dose (De) in unheated sedimentary quartz. In order to minimise sensitivity change during the first measurement, the ITL signal is measured at 270 °C following a preheat...

  8. Characterization of silica quartz as raw material in photovoltaic applications

    Science.gov (United States)

    Boussaa, S. Anas; Kheloufi, A.; Zaourar, N. Boutarek; Kefaifi, A.; Kerkar, F.

    2016-07-01

    Raw materials are essential for the functioning of modern societies, and access to these raw materials is vital to the world economy. Sustainable development, both globally level, raises important new challenges associated with access and efficient use of raw materials. High purity quartz, is consider as a critical raw material and it is a rare commodity that only forms under geological conditions where a narrow set of chemical and physical parameters is fulfilled. When identified and following special beneficiation techniques, high purity quartz obtains very attractive prices and is applied in high technology sectors that currently are under rapid expansion such as photovoltaic solar cells, silicon metal - oxide wafers in the semiconductor industry and long distance optical fibers that are used in communication networks. Crystalline silicon remains the principal material for photovoltaic technology. Metallurgical silicon is produced industrially by the reduction of silica with carbon in an electric arc furnace at temperatures higher than 2000 °C in the hottest parts, by a reaction that can be written ideally as: SiO2 + 2C = Si + 2CO. The aim of this study has been to test experimental methods for investigating the various physical and chemical proprieties of Hoggar quartz with different techniques: X Ray Fluorescence, infra-red spectroscopy, Scanning Electron Microscopy, Optic Microscopy, Carbon Analyzer and Vickers Hardness. The results show finally that the quartz has got good result in purity but need enrichment for the photovoltaic application.

  9. Characterization of silica quartz as raw material in photovoltaic applications

    Energy Technology Data Exchange (ETDEWEB)

    Boussaa, S. Anas, E-mail: sabiha.anas@gmail.com; Kheloufi, A.; Kefaifi, A.; Kerkar, F. [Division croissance cristalline et procédés métallurgiques CCPM Centre de recherche en technologie des semi-conducteurs pour l’énergétique (C.R.T.S.E) 02 Bd Frantz Fanon BP. 140 Alger 7 merveilles, Alger 16200 (Algeria); Zaourar, N. Boutarek [Laboratoire des technologies des matériaux, USTHB, B.P. 32 El Alia, Bab Ezzouar, Alger, Algérie 16111 (Algeria)

    2016-07-25

    Raw materials are essential for the functioning of modern societies, and access to these raw materials is vital to the world economy. Sustainable development, both globally level, raises important new challenges associated with access and efficient use of raw materials. High purity quartz, is consider as a critical raw material and it is a rare commodity that only forms under geological conditions where a narrow set of chemical and physical parameters is fulfilled. When identified and following special beneficiation techniques, high purity quartz obtains very attractive prices and is applied in high technology sectors that currently are under rapid expansion such as photovoltaic solar cells, silicon metal - oxide wafers in the semiconductor industry and long distance optical fibers that are used in communication networks. Crystalline silicon remains the principal material for photovoltaic technology. Metallurgical silicon is produced industrially by the reduction of silica with carbon in an electric arc furnace at temperatures higher than 2000 °C in the hottest parts, by a reaction that can be written ideally as: SiO{sub 2} + 2C = Si + 2CO. The aim of this study has been to test experimental methods for investigating the various physical and chemical proprieties of Hoggar quartz with different techniques: X Ray Fluorescence, infra-red spectroscopy, Scanning Electron Microscopy, Optic Microscopy, Carbon Analyzer and Vickers Hardness. The results show finally that the quartz has got good result in purity but need enrichment for the photovoltaic application.

  10. Atomistic Molecular Dynamics Simulations of Shock Compressed Quartz

    CERN Document Server

    Farrow, Matthew R

    2011-01-01

    Atomistic non-equilibrium molecular dynamics (NEMD) simulations of shock wave compression of quartz have been performed using the so-called BKS semi-empirical potential of van Beest, Kramer and van Santen to construct the Hugoniot of quartz. Our scheme mimics the real world experimental set up by using a flyer-plate impactor to initiate the shock wave and is the first shock wave simulation that uses a geom- etry optimised system of a polar slab in a 3-dimensional system employing periodic boundary conditions. Our scheme also includes the relaxation of the surface dipole in the polar quartz slab which is an essential pre-requisite to a stable simulation. The original BKS potential is unsuited to shock wave calculations and so we propose a simple modification. With this modification, we find that our calculated Hugoniot is in good agreement with experimental shock wave data up to 25 GPa, but significantly diverges beyond this point. We conclude that our modified BKS potential is suitable for quartz under repres...

  11. Aromaticity Competition in Differentially Fused Borepin-Containing Polycyclic Aromatics.

    Science.gov (United States)

    Messersmith, Reid E; Siegler, Maxime A; Tovar, John D

    2016-07-01

    This report describes the synthesis and characterization of a series of borepin-based polycyclic aromatics bearing two different arene fusions. The borepin synthesis features streamlined Ti-mediated alkyne reduction, leading to Z-olefins, followed by direct lithiation and borepin formation. These molecules allow for an assessment of aromatic competition between the fused rings and the central borepin core. Crystallographic, magnetic, and computational studies yielded insights about the aromaticity of novel, differentially fused [b,f]borepins and allowed for comparison to literature compounds. Multiple borepin motifs were also incorporated into polycyclic aromatics with five or six rings in the main backbone, and their properties were also evaluated.

  12. Iatrogenic mid-root perforation of fused teeth

    Directory of Open Access Journals (Sweden)

    Vijay Kumar

    2012-01-01

    Full Text Available Fusion is defined as a union between the dentin and/or enamel of two or more distinct dental sprouts that occurs at any stage of the dental organ. Its prevalence ranges from 0.5%-2.5% in the primary dentition alone and 0.1%-1% of the primary as well as the permanent dentition. These fused teeth can cause various problems such as caries, periodontal disease, abnormal eruption, impaction or an ectopic eruption of an adjacent tooth and reported in the literature. However this paper documented an unusual case of iatrogenic root perforation of fused permanent lower anterior teeth during inter maxillary fixation.

  13. Mechanical and ultrastructural evaluation of quartz post-endodontic reconstructions.

    Science.gov (United States)

    Majori, M; Bedini, R; Altamura, C; Filippini, P; Caiazza, S

    2004-01-01

    Aesthetics is a very important element in dentistry, but requires the support of good mechanical performance. Quartz fiber used in post-endodontic reconstruction is an aesthetic material, although there is little research concerning its mechanical properties. This study evaluated the retentive property of post-endodontic reconstruction, composed of a quartz fiber post. Different thermal stresses were applied in vitro to post-endodontic reconstructions, in order to simulate oral thermal action on post-system dental structure linkage. We chose 30 human extracted teeth, endodontically treated and restored, and then divided them into three groups of 10 teeth. A different treatment was applied to each group before mechanical testing: in the 1st group no treatment was done (controls); in the 2nd group teeth were subjected, in a climatic chamber, to 10 thermo-cycles between 4 degrees C and 58 degrees C; in the 3rd group teeth were stored in a saline solution at 37 degrees C for 48 hr. The teeth then underwent tensile shear stress tests at break point using a computerized electronic dynamometer. After mechanical testing, two teeth from each group were longitudinally half-sectioned, sputter-coated in gold and observed by scanning electron microscopy (SEM). The extracted quartz fiber post of each tooth also underwent SEM observation. Mechanical test results demonstrated that thermal cyclic variations could affect bond stability between dental structures and posts in quartz fiber reconstructions, whereas their bond strength seemed unaffected by humidity increases. Quartz fiber post SEM observation demonstrated a homogeneous structure and a regular fiber disposition. Dental root canal morphology SEM images always showed a different thickness in the cement layer. (Journal of Applied Biomaterials & Biomechanics 2004; 2: 156-61).

  14. Phototoxic maculopathy induced by quartz infrared heat lamp

    Science.gov (United States)

    Zheng, Xinhua; Xie, Ping; Hu, Zizhong; Zhang, Weiwei; Liang, Kang; Wang, Xiuying; Liu, Qinghuai

    2017-01-01

    Abstract Rationale: A large proportion of the output of quartz infrared heat lamps is emitted as infrared radiation (IR). Retinal damage induced by IR-A and visible light on arc welders has been reported. However, case reports of retinal damage caused by quartz infrared heat lamps are rare. To the best of our knowledge, this is the first reported case of phototoxic maculopathy induced by quartz infrared heat lamps. Patient concerns: We report a female with a 1-month history of progressive blurred vision and dysmorphopsia in her right eye after improper staring at the tubes of a quartz infrared heater. Her best corrected visual acuity of the right eye was 20/32. Optical coherence tomography revealed a defect from the ellipsoid zone to retinal pigment epithelium (RPE)/Bruch's complex layer with a diameter of 360mmat its widest. P1 amplitudes in the two central concentric rings were reduced as assessed by multifocal electroretinography. Diagnoses: The patient was diagnosed with phototoxic maculopathy. Interventions: The patient was advised to cease all exposure to the infrared heater and was treated with peribulbar injections of methylprednisolone, oral Pancreatic Kininogenase, and oral Mecobalamin. Outcomes: Ten months later, her BCVA improved to 20/20. All examination results returned to normal except for a small residual defect in the interdigitation zone and RPE/Bruch's complex layer in her optical coherence tomography. Lessons: Light emitted by quartz infrared heat lamps may cause damage to the retina through photothermal and photochemical means. The public is insufficiently aware of the hazard potential of infrared heat lamps and other IR-A sources on human retina. PMID:28099337

  15. Implant success!!!.....simplified

    Directory of Open Access Journals (Sweden)

    Luthra Kaushal

    2009-01-01

    Full Text Available The endeavor towards life-like restoration has helped nurture new vistas in the art and science of implant dentistry. The protocol of "restoration-driven implant placement" ensures that the implant is an apical extension of the ideal future restoration and not the opposite. Meticulous pre-implant evaluation of soft and hard tissues, diagnostic cast and use of aesthetic wax-up and radiographic template combined with surgical template can simplify the intricate roadmap for appropriate implant treatment. By applying the harmony of artistic skill, scientific knowledge and clinical expertise, we can simply master the outstanding implant success in requisites of aesthetics, phonetics and function.

  16. Optically stimulated exoelectron emission processes in quartz: comparison of experiment and theory

    DEFF Research Database (Denmark)

    Pagonis, V.; Ankjærgaard, Christina; Murray, A.S.

    2009-01-01

    Recent experiments have demonstrated that it is possible to measure optically stimulated exoelectron emission (OSE) signals simultaneously with optically stimulated luminescence (OSL) from quartz samples. These experiments provide valuable information on the charge movement in quartz grains. Two...

  17. Properties and behavior of quartz for the silicon process

    Energy Technology Data Exchange (ETDEWEB)

    Aasly, Kurt

    2008-07-01

    This PhD-thesis is a result of the study on important properties of quartz as a raw material for the metallurgical production of ferrosilicon and silicon metal. This includes defining mechanical properties important for the size reduction experienced during transport and storage and thermo-mechanical properties of quartz that is important for how the quartz reacts to the high temperatures experienced as it is charged on the furnace. Additionally, softening properties of quartz have been briefly discussed in some of the papers. Another important goal has been to test analytical and experimental methods for investigating the various properties. The investigations of important factors for the mechanical properties of ores and industrial minerals have been carried out as a literature study. The mining operation and transport from mine to smelter has been discussed and several factors that are significant for achieving best possible mechanical properties of the quartz have been identified. The most important factors are related to production in the mine and processing plant, which should be carefully planned to minimize the amount of blast-induced damage in the rock and thus achieve the best possible mechanical strength of the raw material. The amount of fines can be minimized by controlling the handling of the raw materials during the transport and storage. It is especially important to avoid high drops, both high single drops and accumulated height of all the drops in total. Investigations of the thermo-mechanical properties of quartz have been carried out by using different experimental and characterization methods. The petrographic investigations of the raw materials by polarized light microscopy have been important. Thermo-mechanical investigations have been high-temperature microthermometry and shock heating of quartz samples in an induction furnace with subsequent investigations of the heated material. The subsequent investigation included polarized- and

  18. Crossed fused renal ectopia: Challenges in diagnosis and management

    Directory of Open Access Journals (Sweden)

    Shailesh Solanki

    2013-01-01

    Full Text Available Aim: Crossed fused renal ectopia is a rare congenital malformation, which is reported to be usually asymptomatic but may have varied presentations. This survey was conducted to study the clinical profile and the challenges posed in the management of this entity. Materials and Methods: Retrospective analysis of 6 patients diagnosed to have crossed fused renal ectopia during 1997-2010. The diagnosis was confirmed during surgical exploration in one patient. In one patient it was detected on antenatal ultrasonography and in the other 4 patients it was detected during investigations for abdominal pain, abdominal mass, anorectal malformation and urinary tract infection. Results: The left moiety was crossed and fused with the right moiety in 4 cases. Ultrasonography was found to be a good screening investigation with useful diagnostic contributions from CT scans, radionuclide scintigraphy and magnetic resonance urography. Micturating cystourethrography revealed presence of VUR in 4 cases, 3 of whom have undergone ureteric reimplantation. Two patients required pyeloplasty for pelviureteric junction obstruction; in one of these patients the upper ureter was entrapped in the isthmus. In one patient, a non-functioning moiety resulted in nephrectomy. All children were asymptomatic at last follow-up with stable renal functions. Conclusions: Crossed fused renal ectopia was detected in most patients during investigation for other problems. It was found more commonly in boys. The left moiety was crossed to the right in the majority of cases. Associated urological problems were found in most cases and required the appropriate surgical management.

  19. Evaluation of a color fused dual-band NVG

    NARCIS (Netherlands)

    Hogervorst, M.A.; Toet, A.

    2009-01-01

    We have tested a prototype dual-band NVG system consisting of two NVGs fitted with filters that split the NVG sensitive range into a short (visual) and a long wavelength (NIR) band. The Color-the-night technique (see Hogervorst & Toet, SPIE D&S ‘08) was used to fuse the images of the two sensors. We

  20. A Review of Variable Slicing in Fused Deposition Modeling

    Science.gov (United States)

    Nadiyapara, Hitesh Hirjibhai; Pande, Sarang

    2016-06-01

    The paper presents a literature survey in the field of fused deposition of plastic wires especially in the field of slicing and deposition using extrusion of thermoplastic wires. Various researchers working in the field of computation of deposition path have used their algorithms for variable slicing. In the study, a flowchart has also been proposed for the slicing and deposition process. The algorithm already been developed by previous researcher will be used to be implemented on the fused deposition modelling machine. To demonstrate the capabilities of the fused deposition modeling machine a case study has been taken. It uses a manipulated G-code to be fed to the fused deposition modeling machine. Two types of slicing strategies, namely uniform slicing and variable slicing have been evaluated. In the uniform slicing, the slice thickness has been used for deposition is varying from 0.1 to 0.4 mm. In the variable slicing, thickness has been varied from 0.1 in the polar region to 0.4 in the equatorial region Time required and the number of slices required to deposit a hemisphere of 20 mm diameter have been compared with that using the variable slicing.

  1. Solid-state recoverable fuse functions as circuit breaker

    Science.gov (United States)

    Thomas, E. F., Jr.

    1966-01-01

    Molded, conductive-epoxy recoverable fuse protects electronic circuits during overload conditions, and then permits them to continue to function immediately after the overload condition is removed. It has low resistance at ambient temperature, and high resistance at an elevated temperature.

  2. Evaluation of a color fused dual-band NVG

    NARCIS (Netherlands)

    Hogervorst, M.A.; Toet, A.

    2009-01-01

    We designed and evaluated a dual-band Night Vision Goggles sensor system. The sensor system consists of two optically aligned NVGs fitted with filters splitting the sensitive range into a visual and a near-infrared band. The Color-the-night technique (Hogervorst & Toet, FUSION2008) was used to fuse

  3. Non-invasive management of fused upper incisors

    Directory of Open Access Journals (Sweden)

    Pouran Samimi

    2012-01-01

    Full Text Available The union of two different dental sprouts which can happen in any phase of dental development is commonly called fusion. This developmental anomaly may cause clinical problems including esthetic impairment, which are mainly treated by endodontic and surgical treatments. There are a few reports of conservative not invasive treatment of fused incisors teeth through restorative or prosthetic techniques. They are rarely reported in mandibular posterior teeth. This paper presents an unusual case of fusion of 7 and 8, and also 9 and 10 teeth which was treated with a nonendodontic and nonsurgical conservative approach. Patient was a healthy18-year-old female with chief complaint of bad-looking teeth that in intraoral examination revealed the fusion of 7 and 8, and also 9 and 10 teeth. The space between the mesial of the 6 and 11 teeth was reconstructed. Diastema between the fused teeth was closed. A new lateral tooth was replaced between the fused teeth (7 and 8 and 6 tooth with direct fiber-reinforced composite. The space between the fused teeth (9 and 10 and also tooth 11 was partially closed. Gingival papillas were reconstructed using pink composite. The mandibular anterior missing teeth were replaced with rochett bridge. At the end of treatment the esthetic of the patient was improved. As the treatment was not invasive, major complications are not expected; however, there is potential for eventual long-term periodontal problems due to poor oral hygiene. Debonding of the rochett bridge may happen as well.

  4. Non-invasive management of fused upper incisors.

    Science.gov (United States)

    Samimi, Pouran; Shirban, Mohammad-Reza; Arbabzadeh-Zavareh, Farahnaz

    2012-01-01

    The union of two different dental sprouts which can happen in any phase of dental development is commonly called fusion. This developmental anomaly may cause clinical problems including esthetic impairment, which are mainly treated by endodontic and surgical treatments. There are a few reports of conservative not invasive treatment of fused incisors teeth through restorative or prosthetic techniques. They are rarely reported in mandibular posterior teeth. This paper presents an unusual case of fusion of 7 and 8, and also 9 and 10 teeth which was treated with a nonendodontic and nonsurgical conservative approach. Patient was a healthy18-year-old female with chief complaint of bad-looking teeth that in intraoral examination revealed the fusion of 7 and 8, and also 9 and 10 teeth. The space between the mesial of the 6 and 11 teeth was reconstructed. Diastema between the fused teeth was closed. A new lateral tooth was replaced between the fused teeth (7 and 8) and 6 tooth with direct fiber-reinforced composite. The space between the fused teeth (9 and 10) and also tooth 11 was partially closed. Gingival papillas were reconstructed using pink composite. The mandibular anterior missing teeth were replaced with rochett bridge. At the end of treatment the esthetic of the patient was improved. As the treatment was not invasive, major complications are not expected; however, there is potential for eventual long-term periodontal problems due to poor oral hygiene. Debonding of the rochett bridge may happen as well.

  5. New developments in fused deposition modeling of ceramics

    DEFF Research Database (Denmark)

    Bellini, Anna; Shor, L.; Guceri, S.I.

    2005-01-01

    Purpose - To shift from rapid prototyping (RP) to agile fabrication by broadening the material selection, e.g. using ceramics, hence improving the properties (e.g. mechanical properties) of fused deposition modeling (FDM) products. Design/methodology/approach - This paper presents the development...

  6. The role of quartz in the origin of optical activity on earth.

    Science.gov (United States)

    Evgenii, K; Wolfram, T

    2000-10-01

    A thorough analysis of literature data on distribution of right and left quartz in many locations on the surface of Earth indicates that quartz enantiomorph crystals are distributed in equal amounts in all locations. Therefore optically active quartz crystals of one or the other enantiomorph could not serve as the source of homochirality in the evolution of biosphere. Hence the calculation of a PVED based on published 'small excess of left quartz crystals' on Earth lacks a sound physical basis.

  7. Orientation of Planar Deformation Features (PDFs) in quartz

    Science.gov (United States)

    Langenhorst, F.; Deutsch, A.

    1993-01-01

    Differently oriented single crystal quartz was shocked experimentally at pressures of 20 to 32 GPa and pre-shock temperatures up to 630 C. Based on this systematic investigation, we can demonstrate that the orientation of planar deformation features in quartz is not only dependent on shock pressure but also on pre-shock temperature and shock direction. Moreover, the orientation of Planar Deformation Features (PDF's) is strongly influenced by the set-up in recovery experiments. PDF's in quartz are defined as optically recognizable, planar microstructures diagnostically produced by shock compression. PDF's differ from all kinds of microstructures found in volcanic environment and therefore, their presence is a primary criterion for recognizing impact craters and ejecta layers such as the K/T boundary. Because experiments have shown a pressure dependence of the orientation of PDF's, this property is used extensively for shock wave barometry in natural impact sites. However, the unreflected application of experimental results neglects that parameters such as pre-shock temperature, shock direction, or the experimental arrangement may influence the spatial distribution of PDF's. In order to test this assumption, shock experiments on single crystal quartz at pre-shock temperatures of 20, 275, 540, and 630 C, and with shock directions (1010) and (0001) were performed. Most of the recovery experiments were carried out by using a reverberation technique, whereas in only one experiment a single shock was produced (impedance method). In the former case 0.5 mm thin discs of single crystal quartz were used, in the latter a 15 mm thick cylinder. The orientation of PDF's was measured by means of a conventional universal stage and the results are given. Effects of the experimentation technique can be derived showing the orientation of PDF's in quartz shocked at 27.5 GPa. In comparison to the well defined peaks at (1012) found in samples from reverberation experiments, the impedance

  8. Breast Implants: Saline vs. Silicone

    Science.gov (United States)

    ... differ in material and consistency, however. Saline breast implants Saline implants are filled with sterile salt water. ... of any age for breast reconstruction. Silicone breast implants Silicone implants are pre-filled with silicone gel — ...

  9. 30 CFR 90.101 - Respirable dust standard when quartz is present.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Respirable dust standard when quartz is present... quartz is present. When the respirable dust in the mine atmosphere of the active workings to which a Part 90 miner is exposed contains more than 5 percent quartz, the operator shall continuously maintain...

  10. 30 CFR 71.101 - Respirable dust standard when quartz is present.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Respirable dust standard when quartz is present... UNDERGROUND COAL MINES Dust Standards § 71.101 Respirable dust standard when quartz is present. When the respirable dust in the mine atmosphere of the active workings contains more than 5 percent quartz,...

  11. 30 CFR 70.101 - Respirable dust standard when quartz is present.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Respirable dust standard when quartz is present... Respirable dust standard when quartz is present. When the respirable dust in the mine atmosphere of the active workings contains more than 5 percent quartz, the operator shall continuously maintain the...

  12. Measurement of the dose in quartz in the presence of feldspar contamination

    DEFF Research Database (Denmark)

    Wallinga, J.; Murray, A.S.; Bøtter-Jensen, L.

    2002-01-01

    , without seriously affecting the quartz OSL signal. A single-aliquot regenerative-dose protocol is proposed which, in our samples, allows accurate measurement of the dose in quartz in the presence of feldspar contamination. The protocol also has potential use for quartz dose determination in mixed...

  13. Urinary incontinence - collagen implants

    Science.gov (United States)

    ... gov/ency/article/007373.htm Urinary incontinence - injectable implant To use the sharing features on this page, please enable JavaScript. Injectable implants are injections of material into the urethra to ...

  14. Implantable Medical Devices

    Science.gov (United States)

    ... Artery Disease Venous Thromboembolism Aortic Aneurysm More Implantable Medical Devices Updated:Sep 16,2016 For Rhythm Control ... a Heart Attack Introduction Medications Surgical Procedures Implantable Medical Devices • Life After a Heart Attack • Heart Attack ...

  15. About Implantable Contraception

    Science.gov (United States)

    ... a tube was inserted, and get a new contraceptive implant on schedule or switch to another method of ... continue Possible Side Effects Young women who get contraceptive implants might notice such side effects as: irregular or ...

  16. Breast Reconstruction with Implants

    Science.gov (United States)

    Breast reconstruction with implants Overview By Mayo Clinic Staff Breast reconstruction is a surgical procedure that restores shape to ... treat or prevent breast cancer. One type of breast reconstruction uses breast implants — silicone devices filled with silicone ...

  17. Implantable electronic medical devices

    CERN Document Server

    Fitzpatrick, Dennis

    2014-01-01

    Implantable Electronic Medical Devices provides a thorough review of the application of implantable devices, illustrating the techniques currently being used together with overviews of the latest commercially available medical devices. This book provides an overview of the design of medical devices and is a reference on existing medical devices. The book groups devices with similar functionality into distinct chapters, looking at the latest design ideas and techniques in each area, including retinal implants, glucose biosensors, cochlear implants, pacemakers, electrical stimulation t

  18. A Multi-Fork Z-Axis Quartz Micromachined Gyroscope

    Directory of Open Access Journals (Sweden)

    Aiying Yang

    2013-09-01

    Full Text Available A novel multi-fork z-axis gyroscope is presented in this paper. Different from traditional quartz gyroscopes, the lateral electrodes of the sense beam can be arranged in simple patterns; as a result, the fabrication is simplified. High sensitivity is achieved by the multi-fork design. The working principles are introduced, while the finite element method (FEM is used to simulate the modal and sensitivity. A quartz fork is fabricated, and a prototype is assembled. Impedance testing shows that the drive frequency and sense frequency are similar to the simulations, and the quality factor is approximately 10,000 in air. The scale factor is measured to be 18.134 mV/(°/s and the nonlinearity is 0.40% in a full-scale input range of ±250 °/s.

  19. Deposition and alignment of cells on laser-patterned quartz

    Energy Technology Data Exchange (ETDEWEB)

    George, Sajan D., E-mail: sajan.george@manipal.edu [Centre for Atomic and Molecular Physics, Manipal University, Manipal 576 104 (India); Ladiwala, Uma, E-mail: brainwave@cbs.ac.in [UM-DAE Centre for Excellence in Basic Sciences, Kalina Campus, Mumbai 400 098 (India); Thomas, John; Bankapur, Aseefhali; Chidangil, Santhosh [Centre for Atomic and Molecular Physics, Manipal University, Manipal 576 104 (India); Mathur, Deepak [Tata Institute of Fundamental Research, 1 Homi Bhabha Road, Mumbai 400 005 (India)

    2014-06-01

    Linear grooves have been laser-written on quartz surfaces using ultrashort (50 fs) pulses of 800 nm light. Measurements of water contact angle indicate that laser patterning makes the quartz surface more hydrophilic. Fibroblast cells were cultured on such laser-written surfaces; they were observed to align preferentially along the direction of the laser written grooves (width ∼2 μm. Raman spectroscopy results indicate that there are no chemical changes induced in the surface upon our laser writing. Most unexpectedly, there are also no chemical changes induced in the cells that are spatially aligned along the laser-written grooves. Atomic force microscopy measurements confirm that our laser-writing induces dramatic enhancement of surface roughness along the grooves, and the cells appear to respond to this. Thus, cell alignment seems to be in response to physical cues rather than chemical signals.

  20. New developments in THz quartz enhanced photoacoustic spectroscopy

    Science.gov (United States)

    Spagnolo, Vincenzo; Patimisco, Pietro; Sampaolo, Angelo; Giglio, Marilena; Vitiello, Miriam S.; Scamarcio, Gaetano; Tittel, Frank K.

    2016-09-01

    We will report on new developments of quartz-enhanced photo-acoustic (QEPAS) sensor employing THz quantum cascade laser (QCLs). The extension of the QEPAS technique in the THz range was made possible by the realization of custom made QTFs. With the aim to improve the QTF acousto-electric transduction efficiency, we designed and realized new QTF designs. A detailed analysis of the quality factor, the resonance frequency and the electrical resistance of custom quartz tuning forks (QTFs) with different geometrical parameters is reported. The custom QTFs were employed in QEPAS sensors using THz QCLs as the laser excitation sources and targeting CH3OH and H2S. Minimum detection limits of a few tens of ppb and normalized noise equivalent absorption factors down to 3.75×10-11 cm-1W/Hz½ were achieved.

  1. A multi-fork z-axis quartz micromachined gyroscope.

    Science.gov (United States)

    Feng, Lihui; Zhao, Ke; Sun, Yunan; Cui, Jianmin; Cui, Fang; Yang, Aiying

    2013-01-01

    A novel multi-fork z-axis gyroscope is presented in this paper. Different from traditional quartz gyroscopes, the lateral electrodes of the sense beam can be arranged in simple patterns; as a result, the fabrication is simplified. High sensitivity is achieved by the multi-fork design. The working principles are introduced, while the finite element method (FEM) is used to simulate the modal and sensitivity. A quartz fork is fabricated, and a prototype is assembled. Impedance testing shows that the drive frequency and sense frequency are similar to the simulations, and the quality factor is approximately 10,000 in air. The scale factor is measured to be 18.134 mV/(°/s) and the nonlinearity is 0.40% in a full-scale input range of ±250 °/s.

  2. Annealing Effect on Photovoltages of Quartz Single Crystals

    Institute of Scientific and Technical Information of China (English)

    TIAN Lu; ZHAO Song-Qing; ZHAO Kun

    2010-01-01

    @@ We investigate the photovoltaic effects of quartz single crystals annealed at high temperatures in ambient atmosphere.The open-circuit photovoltages and surface morphologies strongly depend on the heating treatments.When the annealing temperature increases from room temperature to 900℃,the rms roughness of quartz single crystal wafers increases from 0.207 to 1.011 nm.In addition,the photovoltages decrease from 1.994#V at room temperature to 1.551 μ V after treated at 500℃,and then increase up to 9.8μV after annealed at 900℃.The inner mechanism of the present photovoltaic response and surface morphologies is discussed.

  3. Plasma polymerized allylamine coated quartz particles for humic acid removal.

    Science.gov (United States)

    Jarvis, Karyn L; Majewski, Peter

    2012-08-15

    Allylamine plasma polymerization has been used to modify the surface of quartz particles for humic acid removal via an inductively coupled rotating barrel plasma reactor. Plasma polymerized allylamine (ppAA) films were deposited at a power of 25 W, allylamine flow rate of 4.4 sccm and polymerization times of 5-60 min. The influence of polymerization time on surface chemistry was investigated via X-ray photoelectron spectroscopy (XPS), time of flight secondary ion mass spectrometry (ToF-SIMS) and electrokinetic analysis. Acid orange 7 adsorption/desorption quantified the number of surface amine groups. Humic acid removal via ppAA quartz particles was examined by varying pH, removal time, humic acid concentration, and particle mass. Increasing the polymerization time increased the concentration of amine groups on the ppAA quartz surface, thus also increasing the isoelectric point. ToF-SIMS demonstrated uniform distribution of amine groups across the particle surface. Greatest humic acid removal was observed at pH 5 due to electrostatic attraction. At higher pH values, for longer polymerization times, humic acid removal was also observed due to hydrogen bonding. Increasing the initial humic acid concentration increased the mass of humic acid removed, with longer polymerization times exhibiting the greatest increases. Plasma polymerization using a rotating plasma reactor has shown to be a successful method for modifying quartz particles for the removal of humic acid. Further development of the plasma polymerization process and investigation of additional contaminants will aid in the development of a low cost water treatment system.

  4. Quartz red TL SAR equivalent dose overestimation for Chinese loess

    DEFF Research Database (Denmark)

    Lai, Z.P.; Murray, A.S.; Bailey, R.M.

    2006-01-01

    For the red TL of quartz extracted from Chinese loess, the single-aliquot regenerative-dose (SAR) procedure overestimates the known laboratory doses in dose recovery test. The overestimation is the result of the first heating during the measurement of natural TL signal causing a sensitivity...... of red TL, which is found to be more than 100 Gy. (c) 2005 Elsevier Ltd. All rights reserved....

  5. Implantable Heart Aid

    Science.gov (United States)

    1984-01-01

    CPI's human-implantable automatic implantable defibrillator (AID) is a heart assist system, derived from NASA's space circuitry technology, that can prevent erratic heart action known as arrhythmias. Implanted AID, consisting of microcomputer power source and two electrodes for sensing heart activity, recognizes onset of ventricular fibrillation (VF) and delivers corrective electrical countershock to restore rhythmic heartbeat.

  6. Evaluation of the approach to respirable quartz exposure control in U.S. coal mines.

    Science.gov (United States)

    Joy, Gerald J

    2012-01-01

    Occupational exposure to high levels of respirable quartz can result in respiratory and other diseases in humans. The Mine Safety and Health Adminstration (MSHA) regulates exposure to respirable quartz in coal mines indirectly through reductions in the respirable coal mine dust exposure limit based on the content of quartz in the airborne respirable dust. This reduction is implemented when the quartz content of airborne respirable dust exceeds 5% by weight. The intent of this dust standard reduction is to restrict miners' exposure to respirable quartz to a time-weighted average concentration of 100 μg/m(3). The effectiveness of this indirect approach to control quartz exposure was evaluated by analyzing respirable dust samples collected by MSHA inspectors from 1995 through 2008. The performance of the current regulatory approach was found to be lacking due to the use of a variable property-quartz content in airborne dust-to establish a standard for subsequent exposures. In one situation, 11.7% (4370/37,346) of samples that were below the applicable respirable coal mine dust exposure limit exceeded 100 μg/m(3) quartz. In a second situation, 4.4% (895/20,560) of samples with 5% or less quartz content in the airborne respirable dust exceeded 100 μg/m(3) quartz. In these two situations, the samples exceeding 100 μg/m(3) quartz were not subject to any potential compliance action. Therefore, the current respirable quartz exposure control approach does not reliably maintain miner exposure below 100 μg/m(3) quartz. A separate and specific respirable quartz exposure standard may improve control of coal miners' occupational exposure to respirable quartz.

  7. Silicon compounds in solution during bacterial degradation of quartz

    Energy Technology Data Exchange (ETDEWEB)

    Avakyan, Z.A.; Belkanova, N.P.; Karavayko, G.I.; Piskunov, V.P.

    A study was made of the form of silicon compounds in solution in the following systems: distilled water-exopolysaccharides of Bacillus mucilaginosus-monomeric silica; distilled water-suspension of B. mucilaginosus cells-quartz; culture fluids-growing B. mucilaginosus or Thiobacillus thioparus cultures-quartz. In control variants, which contained no exopolysaccharides or bacteria, all of the silicon in solution is demonstrable with the reaction with molybdic acid in the form of monosilicic acid and, perhaps, its lower oligomers. The presence of exopolysaccharides or bacteria leads to the appearance of three forms of silicon compounds: monomeric, polymeric as demonstrable by reaction with molybdic acid after alkaline hydrolysis, and bound, which is demonstrable only by the sintering method. The pH, concentrations of exopolysaccharides and silicon are factors that control the proportion of these forms of silica in the systems studied with exopolysaccharides and resting cells. An increase in the concentration of polysaccharides in the system, as well as changes in medium reaction in the alkaline direction, shift equilibrium toward the formation of the bound form of silica. The mechanism of microbiological degradation of quartz and the formation of silicon compounds is discussed.

  8. Improved electron probe microanalysis of trace elements in quartz

    Science.gov (United States)

    Donovan, John J.; Lowers, Heather; Rusk, Brian G.

    2011-01-01

    Quartz occurs in a wide range of geologic environments throughout the Earth's crust. The concentration and distribution of trace elements in quartz provide information such as temperature and other physical conditions of formation. Trace element analyses with modern electron-probe microanalysis (EPMA) instruments can achieve 99% confidence detection of ~100 ppm with fairly minimal effort for many elements in samples of low to moderate average atomic number such as many common oxides and silicates. However, trace element measurements below 100 ppm in many materials are limited, not only by the precision of the background measurement, but also by the accuracy with which background levels are determined. A new "blank" correction algorithm has been developed and tested on both Cameca and JEOL instruments, which applies a quantitative correction to the emitted X-ray intensities during the iteration of the sample matrix correction based on a zero level (or known trace) abundance calibration standard. This iterated blank correction, when combined with improved background fit models, and an "aggregate" intensity calculation utilizing multiple spectrometer intensities in software for greater geometric efficiency, yields a detection limit of 2 to 3 ppm for Ti and 6 to 7 ppm for Al in quartz at 99% t-test confidence with similar levels for absolute accuracy.

  9. Characterization of hydrothermal green quartz produced by gamma radiation

    Energy Technology Data Exchange (ETDEWEB)

    Enokihara, Cyro T.; Rela, Paulo R., E-mail: cteiti@ipen.br, E-mail: prela06@yahoo.com.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Schultz-Güttler, Rainer A., E-mail: rainersgut@gmail.com [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Instituto de Geociencias

    2015-07-01

    A specific variety of quartz showing a green color in nature or induced artificially by radiation gamma ({sup 60}Co) is quite rare. Only two occurrences are known today, where this type of quartz can be found: Canada, at the Thunder Bay Amethyst Mine, Ontario and Brazil, at widely scattered geode occurrences along a 600 km stretch from Quarai at Brazils southern most tip to Uberlandia in Minas Gerais. These two occurrences have been formed by strong hydrothermal activities.That way much quartz crystals showed a very fast growth history facilitating the formation of growth defects (twinning, small angle tilting, mosaic growth, striations) and the uptake of water in form of micro inclusions, molecular water, silanol (Si-OH) and OH. In the present work the material analyzed is from hydrothermal regimes found in intrusions of basaltic rocks located in the Rio Grande do Sul state. To characterize these materials, colored green by gamma rays, analyses by ICP, electron microscopy, water loss techniques and UV-VIS or NIR-FTIR spectroscopic measurements have been made. Silanol complexes are formed, which by radiation due to gamma rays form the color center NBOHC (Non-bonding Oxygen Hole Center), showing absorption between 590 to 620 nm, responsible for the green color. The water content with up to 3200 ppm by weight exceeds the amount of charge balancing cations (Fe, Al, Li). There is no correlation between water content and cations as in other color varieties. (author)

  10. Voltage-controlled narrowband and wide, variable-range four-segment quartz crystal oscillator.

    Science.gov (United States)

    Ruslan, Ruzaini; Satoh, Tomio; Akitsu, Tetsuya

    2012-03-01

    In this work, our goal is to develop a voltage-controlled variable-frequency quartz crystal oscillator with narrowband response, wide, variable frequency range and the capacity to oscillate across the series resonance frequency using a four-segment configuration of a quartz crystal oscillator. In conventional quartz oscillators, the quartz resonator is inserted in the feedback loop between the input and the output of the active circuit, providing sufficient gain and the phase relation. In the oscillator developed here, the quartz crystal resonator is inserted between the loop circuit and the ground potential. The performance of the voltage-controlled variable-frequency oscillator is demonstrated across the series resonance frequency.

  11. US EPA 2012 Air Quality Fused Surface for the Conterminous U.S. Map Service

    Data.gov (United States)

    U.S. Environmental Protection Agency — This web service contains a polygon layer that depicts fused air quality predictions for 2012 for census tracts in the conterminous United States. Fused air quality...

  12. Experimental deformation in sandstone, carbonates and quartz aggregate

    Energy Technology Data Exchange (ETDEWEB)

    Cheung, Cecilia See Nga [Stony Brook Univ., NY (United States)

    2015-05-01

    The first part of my thesis is mainly focused on the effect of grain size distribution on compaction localization in porous sandstone. To identify the microstructural parameters that influence compaction band formation, I conducted a systematic study of mechanical deformation, failure mode and microstructural evolution in Bleurswiller and Boise sandstones, of similar porosity (~25%) and mineralogy but different sorting. Discrete compaction bands were observed to develop over a wide range of pressure in the Bleurswiller sandstone that has a relatively uniform grain size distribution. In contrast, compaction localization was not observed in the poorly sorted Boise sandstone. My results demonstrate that grain size distribution exerts important influence on compaction band development, in agreement with recently published data from Valley of Fire and Buckskin Gulch, as well as numerical studies. The second part aimed to improve current knowledge on inelastic behavior, failure mode and brittle-ductile transition in another sedimentary rock, porous carbonates. A micritic Tavel (porosity of ~13%) and an allochemical Indiana (~18%) limestones were deformed under compaction in wet and dry conditions. At lower confining pressures, shear localization occurred in brittle faulting regime. Through transitional regime, the deformation switched to cataclastic flow regime at higher confining pressure. Specifically in the cataclastic regime, the (dry and wet) Tavel and dry Indiana failed by distributed cataclastic flow, while in contrast, wet Indiana failed as compaction localization. My results demonstrate that different failure modes and mechanical behaviors under different deformation regimes and water saturation are fundamental prior to any geophysical application in porous carbonates. The third part aimed to focus on investigating compaction on quartz aggregate starting at low (MPa) using X-ray diffraction. We report the diffraction peak evolution of quartz with increasing

  13. Amplifier Module for 260-GHz Band Using Quartz Waveguide Transitions

    Science.gov (United States)

    Padmanabhan, Sharmila; Fung, King Man; Kangaslahti, Pekka P.; Peralta, Alejandro; Soria, Mary M.; Pukala, David M.; Sin, Seth; Samoska, Lorene A.; Sarkozy, Stephen; Lai, Richard

    2012-01-01

    Packaging of MMIC LNA (monolithic microwave integrated circuit low-noise amplifier) chips at frequencies over 200 GHz has always been problematic due to the high loss in the transition between the MMIC chip and the waveguide medium in which the chip will typically be used. In addition, above 200 GHz, wire-bond inductance between the LNA and the waveguide can severely limit the RF matching and bandwidth of the final waveguide amplifier module. This work resulted in the development of a low-loss quartz waveguide transition that includes a capacitive transmission line between the MMIC and the waveguide probe element. This capacitive transmission line tunes out the wirebond inductance (where the wire-bond is required to bond between the MMIC and the probe element). This inductance can severely limit the RF matching and bandwidth of the final waveguide amplifier module. The amplifier module consists of a quartz E-plane waveguide probe transition, a short capacitive tuning element, a short wire-bond to the MMIC, and the MMIC LNA. The output structure is similar, with a short wire-bond at the output of the MMIC, a quartz E-plane waveguide probe transition, and the output waveguide. The quartz probe element is made of 3-mil quartz, which is the thinnest commercially available material. The waveguide band used is WR4, from 170 to 260 GHz. This new transition and block design is an improvement over prior art because it provides for better RF matching, and will likely yield lower loss and better noise figure. The development of high-performance, low-noise amplifiers in the 180-to- 700-GHz range has applications for future earth science and planetary instruments with low power and volume, and astrophysics array instruments for molecular spectroscopy. This frequency band, while suitable for homeland security and commercial applications (such as millimeter-wave imaging, hidden weapons detection, crowd scanning, airport security, and communications), also has applications to

  14. Creep of quartz by dislocation and grain boundary processes

    Science.gov (United States)

    Fukuda, J. I.; Holyoke, C. W., III; Kronenberg, A. K.

    2015-12-01

    Wet polycrystalline quartz aggregates deformed at temperatures T of 600°-900°C and strain rates of 10-4-10-6 s-1 at a confining pressure Pc of 1.5 GPa exhibit plasticity at low T, governed by dislocation glide and limited recovery, and grain size-sensitive creep at high T, governed by diffusion and sliding at grain boundaries. Quartz aggregates were HIP-synthesized, subjecting natural milky quartz powder to T=900°C and Pc=1.5 GPa, and grain sizes (2 to 25 mm) were varied by annealing at these conditions for up to 10 days. Infrared absorption spectra exhibit a broad OH band at 3400 cm-1 due to molecular water inclusions with a calculated OH content (~4000 ppm, H/106Si) that is unchanged by deformation. Rate-stepping experiments reveal different stress-strain rate functions at different temperatures and grain sizes, which correspond to differing stress-temperature sensitivities. At 600-700°C and grain sizes of 5-10 mm, flow law parameters compare favorably with those for basal plasticity and dislocation creep of wet quartzites (effective stress exponents n of 3 to 6 and activation enthalpy H* ~150 kJ/mol). Deformed samples show undulatory extinction, limited recrystallization, and c-axis maxima parallel to the shortening direction. Similarly fine-grained samples deformed at 800°-900°C exhibit flow parameters n=1.3-2.0 and H*=135-200 kJ/mol corresponding to grain size-sensitive Newtonian creep. Deformed samples show some undulatory extinction and grain sizes change by recrystallization; however, grain boundary deformation processes are indicated by the low value of n. Our experimental results for grain size-sensitive creep can be compared with models of grain boundary diffusion and grain boundary sliding using measured rates of silicon grain boundary diffusion. While many quartz mylonites show microstructural and textural evidence for dislocation creep, results for grain size-sensitive creep may apply to very fine-grained (<10 mm) quartz mylonites.

  15. Mineralogy, morphology, and textural relationships in coatings on quartz grains in sediments in a quartz-sand aquifer.

    Science.gov (United States)

    Zhang, Shouliang; Kent, Douglas B; Elbert, David C; Shi, Zhi; Davis, James A; Veblen, David R

    2011-06-01

    Mineralogical studies of coatings on quartz grains and bulk sediments from an aquifer on Western Cape Cod, Massachusetts, USA were carried out using a variety of transmission electron microscopy (TEM) techniques. Previous studies demonstrated that coatings on quartz grains control the adsorption properties of these sediments. Samples for TEM characterization were made by a gentle mechanical grinding method and focused ion beam (FIB) milling. The former method can make abundant electron-transparent coating assemblages for comprehensive and quantitative X-ray analysis and the latter technique protects the coating texture from being destroyed. Characterization of the samples from both a pristine area and an area heavily impacted by wastewater discharge shows similar coating textures and chemical compositions. Major constituents of the coating include Al-substituted goethite and illite/chlorite clays. Goethite is aggregated into well-crystallized domains through oriented attachment resulting in increased porosity. Illite/chlorite clays with various chemical compositions were observed to be mixed with goethite aggregates and aligned sub-parallel to the associated quartz surface. The uniform spatial distribution of wastewater-derived phosphorus throughout the coating from the wastewater-contaminated site suggests that all of the coating constituents, including those adjacent to the quartz surface, are accessible to groundwater solutes. Both TEM characterization and chemical extraction results indicate there is a significantly greater amount of amorphous iron oxide in samples from wastewater discharge area compared to those from the pristine region, which might reflect the impact of redox cycling of iron under the wastewater-discharge area. Coating compositions are consistent with the moderate metal and oxy-metalloid adsorption capacities, low but significant cation exchange capacities, and control of iron(III) solubility by goethite observed in reactive transport

  16. Carbon in intimate contact with quartz reduces the biological activity of crystalline silica dusts.

    Science.gov (United States)

    Ghiazza, Mara; Tomatis, Maura; Doublier, Sophie; Grendene, Francesca; Gazzano, Elena; Ghigo, Dario; Fubini, Bice

    2013-01-18

    To evaluate the effect of carbonaceous materials on the pathogenic activity of quartz dusts, mixtures of carbon soot (1 and 10%) and quartz (Min-U-Sil) were prepared and then milled so to attain an intimate association of carbon and the quartz surface. Both cellular and cell-free tests show that carbon associated to quartz completely inhibits the typical free radical generation of quartz dusts (through Fenton activity and homolytic cleavage of a C-H bond) and suppresses the oxidative stress and inflammation induced by quartz alone on MH-S murine macrophage cells (lipid peroxidation, nitric oxide release, and tumor necrosis factor-α synthesis). The cytotoxic response to quartz is also largely reduced. An extremely pure quartz milled with 10% of soot showed inactivating effects on the adverse reactions to quartz similar to Min-U-Sil quartz. None of these effects takes place when the same experiments are carried out with mechanically mixed samples, which suggests that carbon acts not just as a radical quencher but because of its association to the quartz surface.

  17. Finite element analysis of the dental implant using a topology optimization method.

    Science.gov (United States)

    Chang, Chih-Ling; Chen, Chen-Sheng; Huang, Chang-Hung; Hsu, Ming-Lun

    2012-09-01

    In recent years, many attempts have been made to optimize the shape of dental implants. The purpose of this study took advantage of the topology optimization in the finite element (FE) method to look for redundant material distribution on a dental threaded implant and redesigned a new implant macrogeometry with the evaluation of its biomechanical functions. Three-dimensional FE models were created of a first molar section of the maxilla and embedded with an implant, abutment and a superstructure by using the commercial software ANSYS 11.0. The final design of a new implant was shaped by topology optimization, and four FE models namely traditional implants with bonded (TB) and contact (TC) interfaces, and new implants with bonded (NB) and contact (NC) interfaces, were established. Material properties of compact and cancellous bone were modeled as fully orthotropy and transversely isotropy respectively. Oblique (200-N vertical and 40-N horizontal) occlusal loading was applied on the central and distal fossa of the crown. The FE model estimated that the volume of the new implant could be reduced by 17.9% of the traditional one and the biomechanical performances were similar, such as the stress of the implant, stress of the implant-bone complex, lower displacement, and greater stiffness than the traditional implant. The advantages of the new implant increased the space to allow more new bone ingrowth or assist in fusing more bone graft into the bone sustaining the implant stability and saved material. Its disadvantage was higher stress level compared with that of the traditional implant.

  18. Synergetic Surface and Chemical Durability Study of the Aesthetically Enhanced Natural Quartz by Heat Treatment

    Science.gov (United States)

    Sahoo, Rakesh K.; Rout, Prajna P.; Singh, Saroj K.; Mishra, Barada K.; Mohapatra, Birendra K.

    2017-03-01

    The change in surface behavior of natural quartz stone before and after heat treatment with metal oxides such as: cobalt oxide (Co3O4) and copper oxide (Cu2O) under vacuum and open atmosphere has been investigated. The surface feature, bulk density and hardness value of quartz changed after heat treatment, converting to a high value product. Difference in crystallinity of quartz, pre- and post-heat treatment was obtained through X-ray diffraction (XRD) study. The electron probe microanalysis results clearly explicated the diffusion of metal ion in quartz matrix exposed under vacuum atmosphere but as coating on the surface under open atmosphere. The structural transformation of quartz after heat treatment has been observed from the XRD data and well corroborated with the nanoindentation results. Durability of such quartz to chemical hazardous environment was observed. Thus, this communication demonstrates the change in physical and chemical characteristics of natural quartz stone after heat treatment under different atmosphere.

  19. Synergetic Surface and Chemical Durability Study of the Aesthetically Enhanced Natural Quartz by Heat Treatment

    Science.gov (United States)

    Sahoo, Rakesh K.; Rout, Prajna P.; Singh, Saroj K.; Mishra, Barada K.; Mohapatra, Birendra K.

    2017-01-01

    The change in surface behavior of natural quartz stone before and after heat treatment with metal oxides such as: cobalt oxide (Co3O4) and copper oxide (Cu2O) under vacuum and open atmosphere has been investigated. The surface feature, bulk density and hardness value of quartz changed after heat treatment, converting to a high value product. Difference in crystallinity of quartz, pre- and post-heat treatment was obtained through X-ray diffraction (XRD) study. The electron probe microanalysis results clearly explicated the diffusion of metal ion in quartz matrix exposed under vacuum atmosphere but as coating on the surface under open atmosphere. The structural transformation of quartz after heat treatment has been observed from the XRD data and well corroborated with the nanoindentation results. Durability of such quartz to chemical hazardous environment was observed. Thus, this communication demonstrates the change in physical and chemical characteristics of natural quartz stone after heat treatment under different atmosphere.

  20. Raman Spectrum Study on Quartz Exsolution in Omphacite of Eclogite and Its Tectonic Significances

    Institute of Scientific and Technical Information of China (English)

    Wang Lu; Jin Zhenmin; He Mouchun

    2003-01-01

    The studies on ultra-microstructure characteristics of quartz exsolution in eclogite and coesite in UHP eclogite of several localities are done with the appliance of laser Raman spectroscopy and Ustage. Research results show that the phase transformation of coesite-quartz in garnet and/or omphacite is a continuous process. Topological relationship is present between quartz exsolution in omphacite and its host mineral which shows orientations of two long axes of quartz exsolution parallel to (100) and (-101) of omphacite. At present, some scholars suggest that the quartz exsolution in omphacite of eclogite is the evidence of UHP metamorphism. However, temperature and pressure condition and the exsolution mechanism of oriented needlelike quartz in omphacite still remain unclear. Therefore, further study should be enhanced on experimental research on exsolution mechanism of super-silicate clinopyroxene, which could provide experimental quantitative constraint on quartz exsolution as UHP indicator.

  1. The effect of quartz on the flotation of pyrite depressed by serpentine

    Directory of Open Access Journals (Sweden)

    Bo Feng

    2015-01-01

    Full Text Available The effect of quartz particles on the flotation of pyrite depressed by serpentine has been investigated through flotation tests, adsorption tests, zeta potential measurements and DLVO calculation. The results show that the presence of hydrophilic serpentine slimes on pyrite surface reduces collector adsorption and results in lower recovery of pyrite. The finer the serpentine slime is, the lower the pyrite recovery will be. Quartz particles do not interfere with pyrite flotation. However, the addition of quartz particles increases the adsorption of collector on pyrite surface and limits the detrimental effect of serpentine on pyrite flotation. The fine-grained quartz is more effective. Zeta potential measurements and DLVO calculation illustrate that the zeta potential of quartz is more negative than that of pyrite and the attraction force between serpentine and quartz is stronger than force between serpentine and pyrite, thus some serpentine slimes were transferred from pyrite surface to quartz in the process of attrition.

  2. Classification of fused face images using multilayer perceptron neural network

    CERN Document Server

    Bhattacharjee, Debotosh; Nasipuri, Mita; Basu, Dipak Kumar; Kundu, Mahantapas

    2010-01-01

    This paper presents a concept of image pixel fusion of visual and thermal faces, which can significantly improve the overall performance of a face recognition system. Several factors affect face recognition performance including pose variations, facial expression changes, occlusions, and most importantly illumination changes. So, image pixel fusion of thermal and visual images is a solution to overcome the drawbacks present in the individual thermal and visual face images. Fused images are projected into eigenspace and finally classified using a multi-layer perceptron. In the experiments we have used Object Tracking and Classification Beyond Visible Spectrum (OTCBVS) database benchmark thermal and visual face images. Experimental results show that the proposed approach significantly improves the verification and identification performance and the success rate is 95.07%. The main objective of employing fusion is to produce a fused image that provides the most detailed and reliable information. Fusion of multip...

  3. Reliability assessment of reserved water disposal with erodible fuse plug

    Directory of Open Access Journals (Sweden)

    Kosichenko Yuriy Mikhaylovich

    Full Text Available Water disposal constructions are one of the most responsible constructions of reservoir hydrosystem, that’s why the a lot of attention was always paid to the problems of estimating and providing their reliability and safety. The most important function of such objects is providing reliability and safety of other hydraulic constructions and economic assets in afterbay and water head. The authors offer estimation method for reliability and faultless performance of reserved water disposal with erodible fuse plug on low-head water development. In order to estimate the reliability of reserved water disposal with erodible fuse plug the Bayesian treatment was used. The calculation of diagnoses (states of reserved water disposal isoffered in case of diagnostic properties k 1 and k 2. One of the main demands placed onreserved water disposals is erosion of soil plug in case of flood discharge exeedance over the estimated frequency with the full opening of the waste sluice.

  4. COCHLEAR IMPLANTATION: MY EXPERIENCE

    Directory of Open Access Journals (Sweden)

    Shankar

    2015-12-01

    Full Text Available Cochlear implant is a small, surgically implanted complex electronic device that can help to provide a sense of sound to a person with severe to profound sensorineural hearing loss. This type of hearing loss, typically involves damage to hair cells in the cochlea, as a result sound cannot reach the auditory nerve which usually receives information from hair cells. A cochlear implant skips the damaged hair cells and to stimulate the auditory nerve directly. An implant does not restore normal hearing, instead it can give a deaf person a useful representation of sounds in the environment and help him or her to understand speech. I am here presenting this article in relation to the indications, intraoperative and postoperative complications of cochlear implantation in our institute since January 2013. Children who receive implants at earlier age, outperform their peers who are implanted at a later age. This is reflected in all the areas of speech and language development.

  5. Investigate of Mechanical Fuse in Cardan Shaft Using FEM

    OpenAIRE

    Sayed Poorya Rabiei; Reza Azarafza

    2014-01-01

    A Cardan shaft is a mechanical component for transmitting torque and rotation, usually used to connect drive shaft to driven shaft that cannot be connected directly because of distance or the need to allow for relative movement between them. If overload is applied to cardan shaft, failure can occur in each part of the cardan shaft and maybe some irreparable damage occur to the cardan shaft. Thus it is important to investigate the existence of mechanical fuse in cardan shaft, and this subjcet ...

  6. Fused silica suspension for the VIRGO optics: status and perspectives

    CERN Document Server

    Amico, P; Carbone, L; Gammaitoni, L; Punturo, M; Travasso, F; Vocca, H

    2002-01-01

    Thermal noise in mirror suspension wires is the main limitation of low-frequency sensitivity of interferometric gravitational wave detectors. In order to minimize the pendulum thermal noise, a monolithic design, using a low dissipation material, is proposed for VIRGO. High mechanical Qs and high breaking strengths have been obtained for monolithic fused silica fibres. A low-dissipation and high-strength bonding technique using potassium silicate bonding is proposed.

  7. HEp-2 Cell Classification via Fusing Texture and Shape Information

    OpenAIRE

    Qi, Xianbiao; Zhao, Guoying; Li, Chun-Guang; Guo, Jun; Pietikäinen, Matti

    2015-01-01

    Indirect Immunofluorescence (IIF) HEp-2 cell image is an effective evidence for diagnosis of autoimmune diseases. Recently computer-aided diagnosis of autoimmune diseases by IIF HEp-2 cell classification has attracted great attention. However the HEp-2 cell classification task is quite challenging due to large intra-class variation and small between-class variation. In this paper we propose an effective and efficient approach for the automatic classification of IIF HEp-2 cell image by fusing ...

  8. Fusing Laser and Radar Data for Enhanced Situation Awareness

    OpenAIRE

    Eliasson, Emanuel

    2010-01-01

    With an increasing traffic intensity the demands on vehicular safety is higher than ever before. Active safety systems that have been developed recent years are a response to that. In this master thesis Sensor Fusion is used to combine information from a laser scanner and a microwave radar in order to get more information about the surroundings in front of a vehicle. The Extended Kalman Filter method has been used to fuse the information from the sensors. The process model consists partly of ...

  9. Non-invasive management of fused upper incisors

    OpenAIRE

    Pouran Samimi; Mohammad-Reza Shirban; Farahnaz Arbabzadeh-Zavareh

    2012-01-01

    The union of two different dental sprouts which can happen in any phase of dental development is commonly called fusion. This developmental anomaly may cause clinical problems including esthetic impairment, which are mainly treated by endodontic and surgical treatments. There are a few reports of conservative not invasive treatment of fused incisors teeth through restorative or prosthetic techniques. They are rarely reported in mandibular posterior teeth. This paper presents an unusual case o...

  10. Tetrakis(4-tert-butylphenyl) substituted and fused quinoidal porphyrins

    KAUST Repository

    Zeng, Wangdong

    2012-01-01

    4-tert-Butylphenyl-substituted and fused quinoidal porphyrins 1 and 2 are prepared for the first time. They show (1) intense one-photon absorption in the far-red/near-infrared region, (2) enhanced two-photon absorption compared with aromatic porphyrin monomers, and (3) amphoteric redox behavior. Their geometry and electronic structure are studied by DFT calculations. This journal is © 2012 The Royal Society of Chemistry.

  11. Implantes transcigomáticos Traszygomatic implants

    OpenAIRE

    B. Fernández Ateca; M. Colorado Bonnin; C. Gay Escoda

    2004-01-01

    Los implantes cigomáticos, originariamente diseñados por Branemark en 1989, son implantes de cabeza en 45 grados, de 4'5 milímetros de diámetro en su parte más ancha, y que pueden medir entre 30 y 50 milímetros de longitud. Se insertan desde la parte palatina del proceso alveolar, siguiendo la cresta cigomática-alveolar hasta anclarse en el cuerpo del malar, y en el caso de pacientes maxilectomizados, entrando directamente en el cuerpo del malar. Estos implantes ofrecen una alternativa más al...

  12. Influence of System Parameters on Fuse Protection Use in Regenerative DC Drives

    Directory of Open Access Journals (Sweden)

    Isa Salman Qamber

    2009-06-01

    Full Text Available Current limiting fuses are widely used to protect the thyristors in DC drive systems. One very important problem is the choice of the correct voltage rating for fuses protecting regenerative DC drives, where many types of fault may occur, which makes fuse protection difficult. In the event of a commutation failure while regenerating, the fuses need to interrupt the loop supplied by the AC and DC voltages acting in series, which is the most difficult case for protection by fuses. In this paper a detailed study of the complete interruption process has been investigated by modeling of arcing process of the fuse protection against the regenerative circuit internal commutation fault. The effect of varying the motor time constant, supply impedance, number of fuses used to clear the fault and DC machine rating on the total transient response is studied. The model of a 200 A fuse is employed in this study. Fuses in series with both the semiconductor devices (F1 and fuses in AC lines (F2 are considered. Comparison was made between arc energy produced for fuses protecting the regenerative circuit if failure occurs, with the arc energy produced in a standard AC test in order to investigate the required voltage rating for the fuse.

  13. Study of Fragmentation Process of Fused Fluxes Using Air

    Directory of Open Access Journals (Sweden)

    Daniel Pérez Pérez

    2011-06-01

    Full Text Available In the paper the fragmentation process with air of fused fluxes is studied by means of a particular treatment of the interaction process between the air and flux fluids starting from physical and mathematical considerations of the collision phenomenon which are the result of the application of Newton's mechanics-classical theory. In the paper is schematized the impact and change of trajectory process of the incandescent fused flux flow because of the air mechanical action provided by a blowpipe and the equations referred to the interaction between the fluids are set. As a result, the equations for estimating the exit angle and the average velocities of the pellets formed are determined whenever the interacting air and flux fluxes are known as well as the incidence angles. From the theory developed the essential parameters of the granulation process with air of fused fluxes, by considering the average diameter of the particles to be obtained for their industrial performance can be estimated.

  14. Sampled MTF of fused fiber optic components and bonded assemblies

    Science.gov (United States)

    Carter, Thomas

    2013-05-01

    Fused fiber optic devices are bundles of glass optical fibers that have been successively bundled and drawn to smaller and smaller sizes, effectively creating a "zero optical path window". Due to the nature of fiber's clad and core design, pixelization or sampling of the resulting image occurs; this sampling fundamentally degrades the image. Degradation of a resulting image caused by an optical system can be quantified by way of its Modulation Transfer Function. However, since fused fiber optic devices first sample then effectively project the original image, they do not meet the Fourier transform's prerequisite conditions of being linear and isoplanatic. Current technologies at SCHOTT Lighting and Imaging have initiated a study to determine methodology for measuring the sampled modulation transfer function of bonded assemblies such as bonded Faceplate-to-OLED and Faceplate-tosensor assemblies. The use of randomly generated targets imaged through the bonded assemblies proved to be a useful tactic. This paper discusses the test methods developed and subsequent measurement of the sampled modulation transfer function of fused fiber optic bundles and bonded assemblies.

  15. Production of chicken chimeras by fusing blastodermal cells with electroporation

    Institute of Scientific and Technical Information of China (English)

    S.Aritomi; N.Fujihara

    2000-01-01

    Aim: To establish techniques for producing somatic and gennline chimeric chicken by transferring blastodennal cells fused with electroporation. Methods: Stage-X blastodermal cells isolated from freshly laid fertile unincubated white Leghom and Rhode Island red chicken eggs were fused with electroporation. The treated cell suspension was transferred to the recovery medium (DMEM containing 10% FBS) and was injected into the subgerminal cavity of recipient tmincubated embryos (stage X). Results: Of 177 recipient embryos injected with the fusing blastodermal cells, 6 (3.4%) survived to hatching. Somatic chimerism was examined in the melanocyte of the feather. The presence of feathers originating from the donor cell was observed in 1 bird (16.7%) out of the 6 hatched birds. After 21 days of incubation two birds out of five embryos were subjected to polymemse chain reaction (PCR) analysis for W-chromosome-specific DNA for each tissue. One bird possessed W-chromosome-specific DNA in the stomach, and the other exhibited the same DNA in the left and right gonads and other tissues, but not the stomach. Conclusion: Recipient embryo having electrofused blastodermal cells yields somatic and germline chimeric chickens more successfully.(Asian J Androl 2000 Dec;2:271-275)

  16. Fluid of fused spheres as a model for protein solution

    Directory of Open Access Journals (Sweden)

    M. Kastelic

    2016-03-01

    Full Text Available In this work we examine thermodynamics of fluid with "molecules" represented by two fused hard spheres, decorated by the attractive square-well sites. Interactions between these sites are of short-range and cause association between the fused-sphere particles. The model can be used to study the non-spherical (or dimerized proteins in solution. Thermodynamic quantities of the system are calculated using a modification of Wertheim's thermodynamic perturbation theory and the results compared with new Monte Carlo simulations under isobaric-isothermal conditions. In particular, we are interested in the liquid-liquid phase separation in such systems. The model fluid serves to evaluate the effect of the shape of the molecules, changing from spherical to more elongated (two fused spheres ones. The results indicate that the effect of the non-spherical shape is to reduce the critical density and temperature. This finding is consistent with experimental observations for the antibodies of non-spherical shape.

  17. Alternative complete-arch cement-retained implant-supported fixed partial denture.

    Science.gov (United States)

    Hofstede, T M; Ercoli, C; Hagan, M E

    1999-07-01

    Early implant prostheses designs, which used screw-retained metal and acrylic resin structures, frequently left a space between the prosthesis and the soft tissue. Common deficiencies of this design included phonetic and esthetic problems and screw loosening. Cement-retained implant prostheses are also used in partially and completely edentulous patients, and are thought to have optimal occlusion and esthetics. Moreover, cement-retained prostheses may induce less stress on the implant, thereby maximizing the possibility of a passive fit. Porcelain fused to metal prostheses have been used mostly in partially edentulous situations. Recently, complete-arch porcelain fused to metal prostheses that replace hard and soft tissue have been used and, although this restoration can have excellent esthetics, there are disadvantages such as high cost, potential framework distortion during fabrication, and difficulty in repairing fractures of in-service porcelain. This article describes an alternative technique for the fabrication of a complete-arch, cement-retained, metal-acrylic resin implant-supported fixed partial denture. When compared with porcelain fused to metal complete-arch restorations, this prostheses is esthetic, has excellent retention and stability, yet is relatively inexpensive to fabricate, and requires less laboratory skill.

  18. A novel technique to repair a transverse sacral fracture in a previously fused lumbosacral spondylolisthesis

    Science.gov (United States)

    Noh, Thomas; Chedid, Mokbel K.

    2016-01-01

    Background: Transverse fractures of the sacrum are rare, and surgical treatment for these fractures ranges from conservative to challenging. Transverse stress fractures of the sacrum after placement of lumbar-to-sacral instrumentation have been previously described. We report a new technique to repair a transverse Type-2 Roy-Camille fracture with spondylolisthesis of S1 over S2 in a previously fused instrumented high-grade L4-L5, L5-S1 spondylolisthesis. Case Description: A 64-year-old female who previously had an L4-L5, L5-S1 fusion for spondylolisthesis presented with excruciating lower back pain and radiculopathy for over 6 months. She was found to have an S1-S2 transverse fracture caused by previous implantation of pedicle screws. She underwent repositioning of several failed right lumbar and sacral screws and then had bilateral S1-S2 screws placed directly across the fracture line. The patient had an unremarkable postoperative course. She discontinued most of her pain medications within 6 weeks postoperatively. In the months following surgery, she reported only minimal lower back pain and no radiculopathy with the last appointment 5 years postoperatively. Conclusions: We describe a novel technique to reduce an iatrogenic transverse type-2 Roy-Camille fracture at S1-S2 in a previously instrumented high-grade L4-L5, L5-S1 spondylolisthesis. The patient's fracture achieved adequate reduction and fusion with symptomatic relief. PMID:28028448

  19. 3D Microporous Scaffolds Manufactured via Combination of Fused Filament Fabrication and Direct Laser Writing Ablation

    Directory of Open Access Journals (Sweden)

    Mangirdas Malinauskas

    2014-09-01

    Full Text Available A 3D printing fused filament fabrication (FFF approach has been implemented for the creation of microstructures having an internal 3D microstructure geometry. These objects were produced without any sacrificial structures or additional support materials, just by precisely tuning the nozzle heating, fan cooling and translation velocity parameters. The manufactured microporous structures out of polylactic acid (PLA had fully controllable porosity (20%–60% and consisted of desired volume pores (~0.056 μm3. The prepared scaffolds showed biocompatibility and were suitable for the primary stem cell growth. In addition, direct laser writing (DLW ablation was employed to modify the surfaces of the PLA structures, drill holes, as well as shape the outer geometries of the created objects. The proposed combination of FFF printing with DLW offers successful fabrication of 3D microporous structures with functionalization capabilities, such as the modification of surfaces, the generation of grooves and microholes and cutting out precisely shaped structures (micro-arrows, micro-gears. The produced structures could serve as biomedical templates for cell culturing, as well as biodegradable implants for tissue engineering. The additional micro-architecture is important in connection with the cell types used for the intention of cell growing. Moreover, we show that surface roughness can be modified at the nanoscale by immersion into an acetone bath, thus increasing the hydrophilicity. The approach is not limited to biomedical applications, it could be employed for the manufacturing of bioresorbable 3D microfluidic and micromechanic structures.

  20. Implant arthroplasty for the distal radioulnar joint.

    Science.gov (United States)

    Scheker, Luis R

    2008-11-01

    The distal radioulnar joint (DRUJ) is a weight-bearing joint; the ulnar head is frequently excised either totally or partially and in some cases is fused because of degenerative, rheumatoid, or posttraumatic arthritis and treated with a "salvage procedure." The result of these procedures is the inability of those patients to lift even minor weight. Articles about these procedures report the ability to pronate and supinate, but they rarely discuss grip strength or lifting capacity. We present an alternative to the salvage procedures that allows full range of motions as well as the ability to grip and lift weights encountered in daily living, such as a gallon of milk. The Aptis total DRUJ replacement prosthesis (Aptis Medical, Louisville, KY), a bipolar self-stabilizing DRUJ endoprosthesis, restores the forearm function. The technique of implantation is presented here.

  1. High-performance fused indium gallium arsenide/silicon photodiode

    Science.gov (United States)

    Kang, Yimin

    Modern long haul, high bit rate fiber-optic communication systems demand photodetectors with high sensitivity. Avalanche photodiodes (APDs) exhibit superior sensitivity performance than other types of photodetectors by virtual of its internal gain mechanism. This dissertation work further advances the APD performance by applying a novel materials integration technique. It is the first successful demonstration of wafer fused InGaAs/Si APDs with low dark current and low noise. APDs generally adopt separate absorption and multiplication (SAM) structure, which allows independent optimization of materials properties in two distinct regions. While the absorption material needs to have high absorption coefficient in the target wavelength range to achieve high quantum efficiency, it is desirable for the multiplication material to have large discrepancy between its electron and hole ionization coefficients to reduce noise. According to these criteria, InGaAs and Si are the ideal materials combination. Wafer fusion is the enabling technique that makes this theoretical ideal an experimental possibility. APDs fabricated on the fused InGaAs/Si wafer with mesa structure exhibit low dark current and low noise. Special device fabrication techniques and high quality wafer fusion reduce dark current to nano ampere level at unity gain, comparable to state-of-the-art commercial III/V APDs. The small excess noise is attributed to the large difference in ionization coefficients between electrons and holes in silicon. Detailed layer structure designs are developed specifically for fused InGaAs/Si APDs based on principles similar to those used in traditional InGaAs/InP APDs. An accurate yet straightforward technique for device structural parameters extraction is also proposed. The extracted results from the fabricated APDs agree with device design parameters. This agreement also confirms that the fusion interface has negligible effect on electric field distributions for devices fabricated

  2. Implantes transcigomáticos Traszygomatic implants

    Directory of Open Access Journals (Sweden)

    B. Fernández Ateca

    2004-12-01

    Full Text Available Los implantes cigomáticos, originariamente diseñados por Branemark en 1989, son implantes de cabeza en 45 grados, de 4'5 milímetros de diámetro en su parte más ancha, y que pueden medir entre 30 y 50 milímetros de longitud. Se insertan desde la parte palatina del proceso alveolar, siguiendo la cresta cigomática-alveolar hasta anclarse en el cuerpo del malar, y en el caso de pacientes maxilectomizados, entrando directamente en el cuerpo del malar. Estos implantes ofrecen una alternativa más al cirujano en el momento de planificar un tratamiento protésico-rehabilitador implantosoportado. Sobretodo, en aquellos pacientes con un maxilar superior atrófico en el que no se pueden realizar injertos óseos o estos han fracasado. El objetivo de este artículo es proponer el protocolo quirúrgico de colocación de los implantes trascigomáticos y revisar la literatura actual sobre la evolución clínica de estos implantes.The zygomatic implants, originally designed by Branemark in 1989, are implants with a 45 degree inclined head, 4'5 millimetre diameter at their widest part and measuring between 30 and 50 millimetres in length. They are inserted from the palatine side of the alveolar process, following the zygomatic-alveolar edge and anchor in the body of the zygomatic bone. In the case of maxillectomized patients, they are inserted directly in the body of the malar bone. These implants offer an additional alternative to the surgeon when planning an implant supported rehabilitation treatment; specially in those patients with an atrophic maxilla in which osseous grafts cannot be realized or these grafts have failed. The objective of this article is to propose the surgical,protocol of placement of traszygomatic implants and to check the current literature on the clinical evolution of these implants.

  3. Thermal dependence of luminescence lifetimes and radioluminescence in quartz

    Energy Technology Data Exchange (ETDEWEB)

    Pagonis, V., E-mail: vpagonis@mcdaniel.edu [McDaniel College, Physics Department, Westminster, MD 21157 (United States); Chithambo, M.L. [Department of Physics and Electronics, Rhodes University, PO BOX 94, Grahamstown 6140 (South Africa); Chen, R. [Raymond and Beverly Sackler School of Physics and Astronomy, Tel-Aviv University, Tel-Aviv 69978 (Israel); Chruścińska, A. [Institute of Physics, Nicholas Copernicus University, 87-100 Toruń (Poland); Fasoli, M. [Department of Materials Science, University of Milano-Bicocca, Via Cozzi 53, 20125 Milano (Italy); Li, S.H. [Department of Earth Sciences, The University of Hong Kong (Hong Kong); Martini, M. [Department of Materials Science, University of Milano-Bicocca, Via Cozzi 53, 20125 Milano (Italy); Ramseyer, K. [Institut für Geologie, Baltzerstrasse 1-3, 3012 Bern (Switzerland)

    2014-01-15

    During time-resolved optical stimulation experiments (TR-OSL), one uses short light pulses to separate the stimulation and emission of luminescence in time. Experimental TR-OSL results show that the luminescence lifetime in quartz of sedimentary origin is independent of annealing temperature below 500 °C, but decreases monotonically thereafter. These results have been interpreted previously empirically on the basis of the existence of two separate luminescence centers L{sub H} and L{sub L} in quartz, each with its own distinct luminescence lifetime. Additional experimental evidence also supports the presence of a non-luminescent hole reservoir R, which plays a critical role in the predose effect in this material. This paper extends a recently published analytical model for thermal quenching in quartz, to include the two luminescence centers L{sub H} and L{sub L}, as well as the hole reservoir R. The new extended model involves localized electronic transitions between energy states within the two luminescence centers, and is described by a system of differential equations based on the Mott–Seitz mechanism of thermal quenching. It is shown that by using simplifying physical assumptions, one can obtain analytical solutions for the intensity of the light during a TR-OSL experiment carried out with previously annealed samples. These analytical expressions are found to be in good agreement with the numerical solutions of the equations. The results from the model are shown to be in quantitative agreement with published experimental data for commercially available quartz samples. Specifically the model describes the variation of the luminescence lifetimes with (a) annealing temperatures between room temperature and 900 °C, and (b) with stimulation temperatures between 20 and 200 °C. This paper also reports new radioluminescence (RL) measurements carried out using the same commercially available quartz samples. Gaussian deconvolution of the RL emission spectra was

  4. A Design of Penetration Ammunition Fuse System Based on Embedded Technology

    Institute of Scientific and Technical Information of China (English)

    LI Qiang; LIU Xiao-ming; XIE Xiao-mei

    2007-01-01

    The hard target smart fuse of penetration ammunition is developing to be smaller,lighter, smarter and multifunction. After analyzing the characteristics of high-g accelerating signals and the penetration algorithms, this paper provides a solution of penetration ammunition fuse system based on embedded technology. This fuse system realizes acquisition of the high-g accelerating signals and uses the appropriate penetration algorithms to process them. The fuse system can not only make the same type of penetration ammunition to attack different kinds of objects accurately, but also meet the other requirements of the function of penetration ammunition fuse system.

  5. A quartz Cherenkov detector for polarimetry at the ILC

    Energy Technology Data Exchange (ETDEWEB)

    Vauth, Annika

    2014-09-15

    At the proposed International Linear Collider (ILC), the use of polarised electron and positron beams is a key ingredient of the physics program. A measurement of the polarisation with a yet unprecedented precision of {sup δP}/{sub P}=0.25% is required. To achieve this, Compton polarimeter measurements in front of and behind the collision point are foreseen. In this thesis, a novel concept for a detector for ILC polarimetry is introduced to eliminate one of the dominating systematics limiting the previous best measurement of beam polarisation: a detector using quartz as Cherenkov medium could increase the tolerance against non-linear photodetector responses. The high refractive index of quartz results in a higher Cherenkov light yield compared to conventional Cherenkov gases. This could allow single-peak resolution in the Cherenkov photon spectra produced by the Compton electrons at the polarimeters. The detailed simulation studies presented in this work imply that such single-peak resolution is possible. Considerations for the choice of a suitable detector geometry are discussed. A four-channel prototype has been constructed and successfully operated in a first testbeam campaign at the DESY testbeam, confirming simulation predictions. Although further studies have to be considered to quantify all aspects of the detector response, the findings of the analysis of the data from the first testbeam are promising with regards to reaching the desired light yield. In the final part of this thesis, the application of a detector concept allowing single-peak resolution to the polarisation measurement at the ILC is examined. Two of the main sources of systematic uncertainties on the polarimeter measurements are detector non-linearities and misalignments. The performance of the suggested quartz detector concept in Monte Carlo studies promises a control of these systematics which meets the precision requirements for ILC polarimetry.

  6. The role of crustal quartz in controlling Cordilleran deformation.

    Science.gov (United States)

    Lowry, Anthony R; Pérez-Gussinyé, Marta

    2011-03-17

    Large-scale deformation of continents remains poorly understood more than 40 years after the plate tectonic revolution. Rock flow strength and mass density variations both contribute to stress, so both are certain to be important, but these depend (somewhat nebulously) on rock type, temperature and whether or not unbound water is present. Hence, it is unclear precisely how Earth material properties translate to continental deformation zones ranging from tens to thousands of kilometres in width, why deforming zones are sometimes interspersed with non-deforming blocks and why large earthquakes occasionally rupture in otherwise stable continental interiors. An important clue comes from observations that mountain belts and rift zones cyclically form at the same locations despite separation across vast gulfs of time (dubbed the Wilson tectonic cycle), accompanied by inversion of extensional basins and reactivation of faults and other structures formed in previous deformation events. Here we show that the abundance of crustal quartz, the weakest mineral in continental rocks, may strongly condition continental temperature and deformation. We use EarthScope seismic receiver functions, gravity and surface heat flow measurements to estimate thickness and seismic velocity ratio, v(P)/v(S), of continental crust in the western United States. The ratio v(P)/v(S) is relatively insensitive to temperature but very sensitive to quartz abundance. Our results demonstrate a surprising correlation of low crustal v(P)/v(S) with both higher lithospheric temperature and deformation of the Cordillera, the mountainous region of the western United States. The most plausible explanation for the relationship to temperature is a robust dynamical feedback, in which ductile strain first localizes in relatively weak, quartz-rich crust, and then initiates processes that promote advective warming, hydration and further weakening. The feedback mechanism proposed here would not only explain

  7. Extensive authigenic quartz overgrowths in the gas-bearing Haynesville-Bossier Shale, USA

    Science.gov (United States)

    Dowey, Patrick J.; Taylor, Kevin G.

    2017-07-01

    In sandstone reservoirs, despite grain rearrangement during compaction, significant pore volumes may be retained prior to the onset of late diagenetic quartz cementation. In mudstone reservoirs, grain rearrangement during compaction results in significant pore volume reduction prior to late diagenesis. Where quartz overgrowths have been previously reported in post-compaction mudstones they have been in volumetrically low concentrations and interpreted as anomalous occurrences. Quartz cementation alters rock brittleness resulting in changes to mechanical fracture properties. Quartz overgrowths reduce reservoir porosity and permeability. We present petrographic evidence of two phases of quartz cement in the Haynesville-Bossier Shale: (i) grain replacive and (ii) quartz overgrowths. Carbonate grain replacement is volumetrically low (primary granular framework surrounding engulfed detrital and early authigenic minerals would indicate that quartz overgrowths are also (iii) replacive. Pressure dissolution of detrital quartz silt grains and smectite-to-illite transformation are likely sources of silica for quartz cement. This study is the first to document large-scale, replacive, authigenic quartz overgrowth development within a producing mudstone.

  8. Fluid inclusions and microstructures in experimentally deformed quartz single crystals

    Science.gov (United States)

    Thust, A.; Tarantola, A.; Heilbronner, R.; Stünitz, H.

    2009-04-01

    The "H2O-weakening" effect that reduces the strength of quartz dramatically (e.g. Griggs & Blacic 1965) is still not understood. For example, Kronenberg & Tullis (1984) conclude that the weakening effect is pressure dependent while Paterson (1989) infers a glide and recovery control of water. Obviously, the spatial distribution and transport of H2O are important factors (Kronenberg et al. 1986, FitzGerald et al. 1991). We have carried out experiments on milky quartz in a Griggs deformation apparatus. Cylinders (6.5 mm in diameter, 12-13 mm in length) from a milky zone of a natural quartz single crystal have been cored in orientations (1) normal to one of the prism planes and (2) 45˚ to and 45˚ to (O+orientation). At 1 GPa confining pressure, 900˚ C and 10-6s-1, the flow strength is 150 MPa for samples with orientation (1). Further experiments are needed to establish the flow strength for orientation (2). FTIR measurements on double-polished thick sections (200-500 μm) in the undeformed quartz material yield an average H2O content of approximately 100 H/106Si. The water is heterogeneously distributed in the sample. Direct measurements on fluid inclusions yield a H2O content of more than 25 000 H/106Si. Thus, the H2O in the undeformed material is predominantly present in fluid inclusions of size from tens to hundred microns. Micro-thermometric measurements at low temperature indicate the presence of different salts in the fluid inclusions. The ice melting temperature, between -6.9 and -7.4˚ C, indicate an average salinity of 10.5 wt% NaCl. After deformation the distribution of H2O is more homogeneous throughout the sample. The majority of the big inclusions have disappeared and very small inclusions of several microns to sub-micron size have formed. FTIR measurements in zones of undulatory extinction and shear bands show an average H2O content of approximately 3000 H/106Si. Moreover, the larger fluid inclusions are characterized by a higher salinity (12 wt%) due

  9. Quartz Crystal Microbalance Operation and In Situ Calibration

    Science.gov (United States)

    Albyn, K. C.

    2004-01-01

    Quartz crystal microbalances (QCMs) are commonly used to measure the rate of deposition of molecular species on a surface. The measurement is often used to select materials with a low outgassing rate for applications where the material has a line of sight to a contamination-sensitive surface. A quantitative, in situ calibration of the balance, or balances, using a pure material for which the enthalpy of sublimation is known, is described in this Technical Memorandum. Supporting calculations for surface dwell times of deposited materials and the effusion cell Clausing factor are presented along with examples of multiple QCM measurements of outgassing from a common source.

  10. Evidence for residual elastic strain in deformed natural quartz

    Energy Technology Data Exchange (ETDEWEB)

    Kunz, Martin; Chen, Kai; Tamura,Nobumichi; Wenk, Hans-Rudolf

    2009-01-30

    Residual elastic strain in naturally deformed, quartz-containing rocks can be measured quantitatively in a petrographic thin section with high spatial resolution using Laue microdiffraction with white synchrotron x-rays. The measurements with a resolution of one micrometer allow the quantitative determination of the deviatoric strain tensor as a function of position within the crystal investigated. The observed equivalent strain values of 800-1200 microstrains represent a lower bound of the actual preserved residual strain in the rock, since the stress component perpendicular to the cut sample surface plane is released. The measured equivalent strain translates into an equivalent stress in the order of {approx} 50 MPa.

  11. Anisotropic ionic transport in quartz: the effect of twin boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Calleja, Mark [Mineral Physics Group, Department of Earth Sciences, University of Cambridge, Cambridge (United Kingdom)). E-mail: mcal00@esc.cam.ac.uk; Dove, Martin T.; Salje, Ekhard K.H. [Mineral Physics Group, Department of Earth Sciences, University of Cambridge, Cambridge (United Kingdom)

    2001-10-22

    Transport of Na{sup +} and Li{sup +} under the influence of an electric field in twinned quartz is simulated using molecular dynamics techniques. Comparison between bulk transport and transport along twin boundaries shows that the cations are trapped inside twin walls for weak fields along the crystallographic c-axis. Stronger fields lead to transport along twin walls with significantly lower mobility than in the bulk. With E along [110], transport in the wall is faster than in the bulk. We observe cation trapping preferentially in the twin walls when E is applied out of the plane of the wall. (author)

  12. The adsorption of methyl methacrylate and vinyl acetate polymers on α-quartz surface: A molecular dynamics study

    Science.gov (United States)

    Yan, Lijing; Yang, Yan; Jiang, Hui; Zhang, Bingjian; Zhang, Hui

    2016-01-01

    The molecular dynamics simulation was used to investigate the adsorption of polymethyl methacrylate (PMMA) and polyvinyl acetate (PVA), the commonly used surface coating materials, on α-quartz surface. The objective is to understand the interactions between quartz surface and polymers. The results clearly show adsorption of both polymers onto the quartz surface. Carbonyl group plays a significant role in the adsorption process. The adsorption energies of PMMA and PVA on α-quartz surface did not show significant difference, however, more hydrogen bonds were observed on the PVA/quartz system than PMMA/quartz. These observations might offer some insights on the polymer-quartz adhesion and its failure mechanism.

  13. Implants in adolescents.

    Science.gov (United States)

    Shah, Rohit A; Mitra, Dipika K; Rodrigues, Silvia V; Pathare, Pragalbha N; Podar, Rajesh S; Vijayakar, Harshad N

    2013-07-01

    Implants have gained tremendous popularity as a treatment modality for replacement of missing teeth in adults. There is extensive research present on the use of implants in adults, but there is a dearth of data available on the same in adolescents. The treatment planning and execution of implant placement in adolescents is still in its infancy. This review article is an attempt to bring together available literature.

  14. Implants in adolescents

    Directory of Open Access Journals (Sweden)

    Rohit A Shah

    2013-01-01

    Full Text Available Implants have gained tremendous popularity as a treatment modality for replacement of missing teeth in adults. There is extensive research present on the use of implants in adults, but there is a dearth of data available on the same in adolescents. The treatment planning and execution of implant placement in adolescents is still in its infancy. This review article is an attempt to bring together available literature.

  15. Implant treatment planning considerations.

    Science.gov (United States)

    Kao, Richard T

    2008-04-01

    As dental implants become a more accepted treatment modality, there is a need for all parties involved with implant dentistry to be familiar with various treatment planning issues. Though the success can be highly rewarding, failure to forecast treatment planning issues can result in an increase of surgical needs, surgical cost, and even case failure. In this issue, the focus is on implant treatment planning considerations.

  16. HA-Coated Implant

    DEFF Research Database (Denmark)

    Daugaard, Henrik; Søballe, Kjeld; Bechtold, Joan E

    2014-01-01

    The goal of osseointegration of orthopedic and dental implants is the rapid achievement of a mechanically stable and long lasting fixation between living bone and the implant surface. In total joint replacements of cementless designs, coatings of calcium phosphates were introduced as a means...... of improving the fixation of implants. Of these, hydroxyapatite (HA) is the most widely used and most extensively investigated. HA is highly osseoconductive, and the positive effect is well documented in both basic and long-term clinical research [1–6]. This chapter describes experimental and clinical studies...... evaluating bone-implant fixation with HA coatings....

  17. Ion implantation technology

    CERN Document Server

    Downey, DF; Jones, KS; Ryding, G

    1993-01-01

    Ion implantation technology has made a major contribution to the dramatic advances in integrated circuit technology since the early 1970's. The ever-present need for accurate models in ion implanted species will become absolutely vital in the future due to shrinking feature sizes. Successful wide application of ion implantation, as well as exploitation of newly identified opportunities, will require the development of comprehensive implant models. The 141 papers (including 24 invited papers) in this volume address the most recent developments in this field. New structures and possible approach

  18. Syntheses of fused tetrahydro--carboline analogues through imide carbonyl activation using BBr3: Evidence for the involvement of fused cyclic -acyliminium ion intermediate

    Indian Academy of Sciences (India)

    Selvaraj Mangalaraj; Jayaraman Selvakumar; Chinnasamy Ramaraj Ramanathan

    2015-05-01

    The fused cyclic -acyliminium ion generated during the imide carbonyl activation reaction of phenethylphthalimide was confirmed by single crystal X-ray diffraction. The Lewis acid assisted imide carbonyl activation methodology was successfully extended to synthesize fused tetrahydro--carboline units from the corresponding -indolylethylimides.

  19. Influence of the preshock temperature on shock effects in quartz

    Science.gov (United States)

    Langenhorst, F.; Deutsch, A.

    1992-01-01

    Shock metamorphic features are the prime indicators for recognizing impact phenomena on Earth and other planetary bodies. Although the pressure dependence of shock features is well known, information about the influence of the preshock temperature is almost lacking. Especially in the case of large-scale impacts like Sudbury, it is expected that deep-seated crustal rocks were subjected to shock at elevated temperatures. Therefore, we continued to perform shock experiments at elevated temperatures on less than 0.5-mm thin disks of single crystal quartz cut parallel to the (1010) face. All recovered quartz samples were investigated by universal stage, spindle stage, and a newly developed density gradient technique. Errors of refractive index and density measurements are +/- 0.0005 and +/- 0.002 g/cu cm respectively. Our investigations indicate that shock metamorphic features are strongly dependent on the preshock temperature. This statement has far-reaching implications with respect to shock wave barometry that is based on data from recovery experiments at room temperature. These datasets might be applicable only to low-temperature target rocks. Moreover, this study demonstrates that shock recovery experiments are definitely required for understanding the complete pressure-temperature regime of shock metamorphism on planetary bodies.

  20. Mass production of CNTs using CVD multi-quartz tubes

    Energy Technology Data Exchange (ETDEWEB)

    Yousef, Samy; Mohamed, Alaa [Dept. of Production Engineering and Printing Technology, Akhbar Elyom Academy, Giza (Egypt)

    2016-11-15

    Carbon nanotubes (CNTs) have become the backbone of modern industries, including lightweight and heavy-duty industrial applications. Chemical vapor deposition (CVD) is considered as the most common method used to synthesize high yield CNTs. This work aims to develop the traditional CVD for the mass production of more economical CNTs, meeting the growing CNT demands among consumers by increasing the number of three particular reactors. All reactors housing is connected by small channels to provide the heat exchange possibility between the chambers, thereby decreasing synthesis time and reducing heat losses inside the ceramic body of the furnace. The novel design is simple and cheap with a lower reacting time and heat loss compared with the traditional CVD design. Methane, hydrogen, argon, and catalyzed iron nanoparticles were used as a carbon source and catalyst during the synthesis process. In addition, CNTs were produced using only a single quartz tube for comparison. The produced samples were examined using XRD, TEM, SEM, FTIR, and TGA. The results showed that the yield of CNTs increases by 287 % compared with those synthesized with a single quartz tube. Moreover, the total synthesis time of CNTs decreases by 37 % because of decreased heat leakage.

  1. A combined nanoplasmonic and electrodeless quartz crystal microbalance setup

    Energy Technology Data Exchange (ETDEWEB)

    Larsson, Elin M.; Langhammer, Christoph; Zoric, Igor; Kasemo, Bengt [Department of Applied Physics, Chemical Physics Group, Chalmers University of Technology, SE-41296 Gothenburg (Sweden); Edvardsson, Malin E. M. [Department of Applied Physics, Biological Physics Group, Chalmers University of Technology, SE-41296 Gothenburg (Sweden)

    2009-12-15

    We have developed an instrument combining localized surface plasmon resonance (LSPR) sensing with electrodeless quartz crystal microbalance with dissipation monitoring (QCM-D). The two techniques can be run simultaneously, on the same sensor surface, and with the same time resolution and sensitivity as for the individual techniques. The electrodeless QCM eliminates the need to fabricate electrodes on the quartz crystal and gives a large flexibility in choosing the surface structure and coating for both QCM-D and LSPR. The performance is demonstrated for liquid phase measurements of lipid bilayer formation and biorecognition events, and for gas phase measurements of hydrogen uptake/release by palladium nanoparticles. Advantages of using the combined equipment for biomolecular adsorption studies include synchronized information about structural transformations and extraction of molecular (dry) mass and degree of hydration of the adlayer, which cannot be obtained with the individual techniques. In hydrogen storage studies the combined equipment, allows for synchronized measurements of uptake/release kinetics and quantification of stored hydrogen amounts in nanoparticles and films at practically interesting hydrogen pressures and temperatures.

  2. Infrared optical properties of $\\alpha$ quartz by molecular dynamics simulations

    CERN Document Server

    Gangemi, Fabrizio; Carati, Andrea; Maiocchi, Alberto; Galgani, Luigi

    2016-01-01

    This paper is concerned with theoretical estimates of the refractive--index curves for quartz, obtained by the Kubo formul\\ae\\ in the classical approximation, through MD simulations for the motions of the ions. Two objectives are considered. The first one is to understand the role of nonlinearities in situations where they are very large, as at the $\\alpha$--$\\beta$ structural phase transition. We show that on the one hand they don't play an essential role in connection with the form of the spectra in the infrared. On the other hand they play an essential role in introducing a chaoticity which involves a definite normal mode. This might explain why that mode is Raman active in the $\\alpha$ phase, but not in the $\\beta$ phase. The second objective concerns whether it is possible in a microscopic model to obtain normal mode frequencies, or peak frequencies in the optical spectra, that are in good agreement with the experimental data for quartz. Notwithstanding a lot of effort, we were unable to find results agr...

  3. Outbreak of silicosis in Spanish quartz conglomerate workers

    Science.gov (United States)

    Pérez-Alonso, Aránzazu; Córdoba-Doña, Juan Antonio; Millares-Lorenzo, José Luis; Figueroa-Murillo, Estrella; García-Vadillo, Cristina; Romero-Morillo, José

    2014-01-01

    Objectives: To describe the epidemiological and clinical characteristics of an outbreak of occupational silicosis and the associated working conditions. Methods: Cases were defined as men working in the stone cutting, shaping, and finishing industry in the province of Cádiz, diagnosed with silicosis between July 2009 and May 2012, and were identified and diagnosed by the department of pulmonology of the University Hospital of Puerto Real (Cádiz). A census of workplaces using quartz conglomerates was carried out to determine total numbers of potentially exposed workers. A patient telephone survey on occupational exposures and a review of medical records for all participants were conducted. Results: Silicosis was diagnosed in 46 men with a median age of 33 years and a median of 11 years working in the manufacturing of countertops. Of these cases, 91.3% were diagnosed with simple chronic silicosis, with an abnormal high-resolution computerized tomography (HRCT) scan. One patient died during the study period. Employer non-compliance in prevention and control measures was frequently reported, as were environmental and individual protection failures. Conclusions: The use of new construction materials such as quartz conglomerates has increased silicosis incidence due to intensive occupational exposures, in the context of high demand fuelled by the housing boom. This widespread exposure poses a risk if appropriate preventive measures are not undertaken. PMID:24804337

  4. Reactive ion etching of quartz and Pyrex for microelectronic applications

    Science.gov (United States)

    Zeze, D. A.; Forrest, R. D.; Carey, J. D.; Cox, D. C.; Robertson, I. D.; Weiss, B. L.; Silva, S. R. P.

    2002-10-01

    The reactive ion etching of quartz and Pyrex substrates was carried out using CF4/Ar and CF4/O2 gas mixtures in a combined radio frequency (rf)/microwave (μw) plasma. It was observed that the etch rate and the surface morphology of the etched regions depended on the gas mixture (CF4/Ar or CF4/O2), the relative concentration of CF4 in the gas mixture, the rf power (and the associated self-induced bias) and microwave power. An etch rate of 95 nm/min for quartz was achieved. For samples covered with a thin metal layer, ex situ high resolution scanning electron microscopy and atomic force microscopy imaging indicated that, during etching, surface roughness is produced on the surface beneath the thin metallic mask. Near vertical sidewalls with a taper angle greater than 80° and smooth etched surfaces at the nanometric scale were fabricated by carefully controlling the etching parameters and the masking technique. A simulation of the electrostatic field distribution was carried out to understand the etching process using these masks for the fabrication of high definition features.

  5. Tree Classification with Fused Mobile Laser Scanning and Hyperspectral Data

    Directory of Open Access Journals (Sweden)

    Juha Hyyppä

    2011-05-01

    Full Text Available Mobile Laser Scanning data were collected simultaneously with hyperspectral data using the Finnish Geodetic Institute Sensei system. The data were tested for tree species classification. The test area was an urban garden in the City of Espoo, Finland. Point clouds representing 168 individual tree specimens of 23 tree species were determined manually. The classification of the trees was done using first only the spatial data from point clouds, then with only the spectral data obtained with a spectrometer, and finally with the combined spatial and hyperspectral data from both sensors. Two classification tests were performed: the separation of coniferous and deciduous trees, and the identification of individual tree species. All determined tree specimens were used in distinguishing coniferous and deciduous trees. A subset of 133 trees and 10 tree species was used in the tree species classification. The best classification results for the fused data were 95.8% for the separation of the coniferous and deciduous classes. The best overall tree species classification succeeded with 83.5% accuracy for the best tested fused data feature combination. The respective results for paired structural features derived from the laser point cloud were 90.5% for the separation of the coniferous and deciduous classes and 65.4% for the species classification. Classification accuracies with paired hyperspectral reflectance value data were 90.5% for the separation of coniferous and deciduous classes and 62.4% for different species. The results are among the first of their kind and they show that mobile collected fused data outperformed single-sensor data in both classification tests and by a significant margin.

  6. Characterization of Optical and Electrical Properties of Transparent Conductive Boron-Doped Diamond thin Films Grown on Fused Silica

    Directory of Open Access Journals (Sweden)

    Bogdanowicz Robert

    2014-12-01

    Full Text Available Abstract A conductive boron-doped diamond (BDD grown on a fused silica/quartz has been investigated. Diamond thin films were deposited by the microwave plasma enhanced chemical vapor deposition (MW PECVD. The main parameters of the BDD synthesis, i.e. the methane admixture and the substrate temperature were investigated in detail. Preliminary studies of optical properties were performed to qualify an optimal CVD synthesis and film parameters for optical sensing applications. The SEM micro-images showed the homogenous, continuous and polycrystalline surface morphology; the mean grain size was within the range of 100-250 nm. The fabricated conductive boron-doped diamond thin films displayed the resistivity below 500 mOhm cm-1 and the transmittance over 50% in the VIS-NIR wavelength range. The studies of optical constants were performed using the spectroscopic ellipsometry for the wavelength range between 260 and 820 nm. A detailed error analysis of the ellipsometric system and optical modelling estimation has been provided. The refractive index values at the 550 nm wavelength were high and varied between 2.24 and 2.35 depending on the percentage content of methane and the temperature of deposition.

  7. Macrophages detoxify the genotoxic and cytotoxic effects of surgical cobalt chrome alloy particles but not quartz particles on human cells in vitro.

    Science.gov (United States)

    Papageorgiou, I; Shadrick, V; Davis, S; Hails, L; Schins, R; Newson, R; Fisher, J; Ingham, E; Case, C P

    2008-08-25

    Particles of surgical cobalt chrome alloy are cytotoxic and genotoxic to human fibroblasts in vitro. In vivo orthopaedic patients are exposed to cobalt chrome particles as a result of wear of a joint replacement. Many of the wear debris particles that are produced are phagocytosed by macrophages that accumulate at the site of the worn implant and are disseminated to local and distant lymph nodes the liver and the spleen. In this study we have tested whether this process of phagocytosis could have altered the cytotoxic and genotoxic properties of the cobalt chrome particles. Quartz particles have been investigated as a control. Micron-sized particles of cobalt chrome alloy were internalised by either white cells of peripheral blood or by THP-1 monocytes for 1 week and 1 day, respectively. The particles were then extracted and presented at different doses to fibroblasts for 1 day. There was a reduction of the cytotoxicity and genotoxicity of the cobalt chrome particles after phagocytosis by white cells or THP-1 cells. Cobalt chrome particles that were internalised by fibroblasts also showed a reduction of their cytotoxicity but not their genotoxicity. In contrast the cytotoxicity and genotoxicity of quartz particles was increased after internalisation by THP-1 cells. The surface morphology of the cobalt chrome particles but not the quartz particles was changed after phagocytosis by THP-1 cells. This study suggests that the genotoxic and cytotoxic properties of particles that fall within the size range for phagocytosis may be highly complex in vivo and depend on the combination of material type and previous phagocytosis. These results may have relevance for particle exposure from orthopaedic implants and from environmental or industrial pollution.

  8. Collaborative Filtering Fusing Label Features Based on SDAE

    DEFF Research Database (Denmark)

    Huo, Huan; Liu, Xiufeng; Zheng, Deyuan

    2017-01-01

    problem, auxiliary information such as labels are utilized. Another approach of recommendation system is content-based model which can’t be directly integrated with CF-based model due to its inherent characteristics. Considering that deep learning algorithms are capable of extracting deep latent features......, this paper applies Stack Denoising Auto Encoder (SDAE) to content-based model and proposes LCF(Deep Learning for Collaborative Filtering) algorithm by combing CF-based model which fuses label features. Experiments on real-world data sets show that DLCF can largely overcome the sparsity problem...

  9. Fused Deposition Technique for Continuous Fiber Reinforced Thermoplastic

    Science.gov (United States)

    Bettini, Paolo; Alitta, Gianluca; Sala, Giuseppe; Di Landro, Luca

    2017-02-01

    A simple technique for the production of continuous fiber reinforced thermoplastic by fused deposition modeling, which involves a common 3D printer with quite limited modifications, is presented. An adequate setting of processing parameters and deposition path allows to obtain components with well-enhanced mechanical characteristics compared to conventional 3D printed items. The most relevant problems related to the simultaneous feeding of fibers and polymer are discussed. The properties of obtained aramid fiber reinforced polylactic acid (PLA) in terms of impregnation quality and of mechanical response are measured.

  10. CHANGE DETECTION BY FUSING ADVANTAGES OF THRESHOLD AND CLUSTERING METHODS

    Directory of Open Access Journals (Sweden)

    M. Tan

    2017-09-01

    Full Text Available In change detection (CD of medium-resolution remote sensing images, the threshold and clustering methods are two kinds of the most popular ones. It is found that the threshold method of the expectation maximum (EM algorithm usually generates a CD map including many false alarms but almost detecting all changes, and the fuzzy local information c-means algorithm (FLICM obtains a homogeneous CD map but with some missed detections. Therefore, we aim to design a framework to improve CD results by fusing the advantages of threshold and clustering methods. Experimental results indicate the effectiveness of the proposed method.

  11. Fused Deposition Technique for Continuous Fiber Reinforced Thermoplastic

    Science.gov (United States)

    Bettini, Paolo; Alitta, Gianluca; Sala, Giuseppe; Di Landro, Luca

    2016-12-01

    A simple technique for the production of continuous fiber reinforced thermoplastic by fused deposition modeling, which involves a common 3D printer with quite limited modifications, is presented. An adequate setting of processing parameters and deposition path allows to obtain components with well-enhanced mechanical characteristics compared to conventional 3D printed items. The most relevant problems related to the simultaneous feeding of fibers and polymer are discussed. The properties of obtained aramid fiber reinforced polylactic acid (PLA) in terms of impregnation quality and of mechanical response are measured.

  12. Nanodrilling of fused silica using nanosecond laser radiation

    Energy Technology Data Exchange (ETDEWEB)

    Lorenz, P., E-mail: pierre.lorenz@iom-leipzig.de; Zajadacz, J.; Bayer, L.; Ehrhardt, M.; Zimmer, K.

    2015-10-01

    Graphical abstract: - Highlights: • Low-fluence irradiation of 10 nm Mo on SiO{sub 2} results in the formation of Mo droplets. • High-fluence irradiation of droplets results in the formation of holes in the SiO{sub 2}. • The process allows the formation of randomly distributed and periodic holes. • The randomly distributed hole density ρ{sub h} depends on the fluence (ρ{sub h} ≤ 1.3 μm{sup −2}). • The interaction of the laser beam with Mo/SiO{sub 2} was simulated by FEM. - Abstract: The fast laser drilling of dielectric surfaces with hole diameters in the sub-μm range and a high aspect ratio is a challenge for laser methods. In this study, a novel laser structuring method for the production of randomly and periodically distributed holes in a fused silica surface will be presented using a self-assembling process. A fused silica surface was covered with a 10 nm thick magnetron-sputtered molybdenum film. The metal film was irradiated by a KrF excimer laser (wavelength λ = 248 nm, pulse duration Δt{sub p} = 25 ns) with low laser fluences (Φ < 1 J/cm{sup 2}) and the laser-induced heating resulting in a melting of the metal film and finally in a self-assembled formation of randomly distributed metal droplets due to the surface tension of the metal liquid phase using a top hat beam profile. Furthermore, the usage of a periodically modulated laser beam profile allows the fabrication of periodically distributed droplet pattern. The multi-pulse irradiation of the laser-generated metal droplets with higher laser fluences results in a stepwise evaporation of the metal and in a partial evaporation of the fused silica near the metal droplets. Finally, the laser-induced stepwise evaporation process results in a formation of cone-like holes in the fused silica surface where the resultant holes are dependent on the size of the generated metal droplets and on the laser parameters. The “drilling” process allows the fabrication of holes with a depth up to 1

  13. Iron-Ion Implantation into the Structure of Rock Crystal

    Directory of Open Access Journals (Sweden)

    A.V. Mukhametshin

    2017-03-01

    Full Text Available Iron ions with the energy of 40 keV have been implanted into colorless natural rock crystals to high fluencies of 1.0∙1017 and 1.5∙1017 ion/cm2. These crystals were selected from Svetlinsky deposits of the Southern Urals, which are well-known as minerals with high quality and low content of impurities. A radical change in the color of the crystals after iron-ion implantation and subsequent high-temperature annealing in air has been revealed. The origin of color changes has been studied by using optical methods, as well as Mössbauer and X-ray photoelectron spectroscopy. It has been established that the high-dose and high-energy flow of ions results in the formation of various kinds of structural defects on the surface layer of the matrix, such as electron-hole centers, as well as in the formation at a specific depth of the irradiated matrix of the ultrafine iron-containing phases with a structure, which is non-coherent to the structure of the original matrix. The subsequent high-temperature annealing of the implanted quartz has changed the color of the samples to orange-yellow. This color is similar to the color of natural citrine. The orange color richness of the heat-treated samples grew with increasing amounts of embedded iron impurity in the crystal. The nature of orange-yellow coloration of the implanted and annealed quartz plates can be explained by the formation of ultrafine hematite nanoparticles located in a layer at a depth of ~15 nm. The possibility of refining the color of minerals by ion-beam exposure has been discussed.

  14. Non-Gold Base Dental Casting Alloys. Volume 2. Porcelain-Fused-to-Metal Alloys.

    Science.gov (United States)

    1986-08-01

    kaolin , and/or alumina. a. Quartz Quartz has a high fusion temperature , and acts as the frimeworK around which the other ingredients can flow.7 Quartz...until it has cooled to room temperature . The metal and the - porcelain retain heat differently , and thus will cool at different rates. Rushing the case at...dental porcelain to a recommended temperature for a specific period of time. SINTERING - Another term to describe the "firing" of dental porcelain

  15. Emplacement of cretaceous-tertiary boundary shocked quartz from chicxulub crater.

    Science.gov (United States)

    Alvarez, W; Claeys, P; Kieffer, S W

    1995-08-18

    Observations on shocked quartz in Cretaceous-Tertiary (K-T) boundary sediments compellingly tied to Chicxulub crater raise three problems. First, in North America shocked quartz occurs above the main K-T ejecta layer. Second, shocked quartz is more abundant west than east of Chicxulub. Third, shocked quartz reached distances requiring initial velocities up to 8 kilometers per second, corresponding to shock pressures that would produce melt, not the moderate-pressure shock lamellae observed. Shock devolatilization and the expansion of carbon dioxide and water from impacted wet carbonate, producing a warm, accelerating fireball after the initial hot fireball of silicate vapor, may explain all three problems.

  16. Changes in Quartz During Heating and the Possible Effects on Si Production

    Science.gov (United States)

    Ringdalen, Eli

    2015-02-01

    In Si and FeSi production, the main Si source is SiO2, in the form of quartz. Reactions with SiO2 generate SiO gas that further reacts with SiC to Si. During heating, quartz will transform to other SiO2 modifications with cristobalite as the stable high-temperature phase. Transformation to cristobalite is a slow process. Its rate has been investigated for several industrial quartz sources and has been shown to vary considerably among the different quartz types. Other differences in behavior during heating between these quartz sources, such as softening temperature and volume expansion, have also been studied. The quartz-cristobalite ratio will affect the rate of reactions involving SiO2. The industrial consequences and other implications of the observed difference between quartz types are discussed. Initial studies of industrial quartz were published by Ringdalen et al. In the current work, a new experimental method has been developed, and an investigation of several new quartz sources has confirmed the earlier observed large variation between different sources. The repeatability of the data has been studied and the effect of gas atmosphere investigated. The results from the earlier work are included as a basis for the discussion.

  17. Grain size distribution of quartz isolated from Chinese loess/paleosol

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Grain size distribution of bulk loess-paleosol and quartz chemically extracted from the loess/paleosol shows that mean size of the bulk samples is always finer than that of the quartz. The original aeolian depositions have been modified to various degrees by post-depositional weathering and pedogenic processes. The grain size distribution of the isolated quartz should be close to that of the primary aeolian sediment because the chemical pretreatment excludes secondary produced minerals. Therefore, the grain size of the quartz may be considered to more clearly reflect the variations of winter monsoon intensity.

  18. Management of peri-implantitis

    OpenAIRE

    Jayachandran Prathapachandran; Neethu Suresh

    2012-01-01

    Peri-implantitis is a site-specific infectious disease that causes an inflammatory process in soft tissues, and bone loss around an osseointegrated implant in function. The etiology of the implant infection is conditioned by the status of the tissue surrounding the implant, implant design, degree of roughness, external morphology, and excessive mechanical load. The microorganisms most commonly associated with implant failure are spirochetes and mobile forms of Gram-negative anaerobes, unless ...

  19. Management of peri-implantitis

    OpenAIRE

    Jayachandran Prathapachandran; Neethu Suresh

    2012-01-01

    Peri-implantitis is a site-specific infectious disease that causes an inflammatory process in soft tissues, and bone loss around an osseointegrated implant in function. The etiology of the implant infection is conditioned by the status of the tissue surrounding the implant, implant design, degree of roughness, external morphology, and excessive mechanical load. The microorganisms most commonly associated with implant failure are spirochetes and mobile forms of Gram-negative anaerobes, unless ...

  20. A study of cathodoluminescence and trace element compositional zoning in natural quartz from volcanic rocks: mapping titanium content in quartz.

    Science.gov (United States)

    Leeman, William P; MacRae, Colin M; Wilson, Nick C; Torpy, Aaron; Lee, Cin-Ty A; Student, James J; Thomas, Jay B; Vicenzi, Edward P

    2012-12-01

    This article concerns application of cathodoluminescence (CL) spectroscopy to volcanic quartz and its utility in assessing variation in trace quantities of Ti within individual crystals. CL spectroscopy provides useful details of intragrain compositional variability and structure but generally limited quantitative information on element abundances. Microbeam analysis can provide such information but is time-consuming and costly, particularly if large numbers of analyses are required. To maximize advantages of both approaches, natural and synthetic quartz crystals were studied using high-resolution hyperspectral CL imaging (1.2-5.0 eV range) combined with analysis via laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS). Spectral intensities can be deconvolved into three principal contributions (1.93, 2.19, and 2.72 eV), for which intensity of the latter peak was found to correlate directly with Ti concentration. Quantitative maps of Ti variation can be produced by calibration of the CL spectral data against relatively few analytical points. Such maps provide useful information concerning intragrain zoning or heterogeneity of Ti contents with the sensitivity of LA-ICPMS analysis and spatial resolution of electron microprobe analysis.

  1. Delayed breast implant reconstruction

    DEFF Research Database (Denmark)

    Hvilsom, Gitte B.; Hölmich, Lisbet R.; Steding-Jessen, Marianne;

    2012-01-01

    We evaluated the association between radiation therapy and severe capsular contracture or reoperation after 717 delayed breast implant reconstruction procedures (288 1- and 429 2-stage procedures) identified in the prospective database of the Danish Registry for Plastic Surgery of the Breast during...... reconstruction approaches other than implants should be seriously considered among women who have received radiation therapy....

  2. Ion Implantation of Polymers

    DEFF Research Database (Denmark)

    Popok, Vladimir

    2012-01-01

    are discussed. Related to that, the effects of radiothermolysis, degassing and carbonisation are considered. Specificity of depth distributions of implanted into polymers impurities is analysed and the case of high-fluence implantation is emphasised. Within rather broad topic of ion bombardment, the focus...

  3. A New Measure for Analyzing and Fusing Sequences of Objects.

    Science.gov (United States)

    Goulermas, John Yannis; Kostopoulos, Alexandros; Mu, Tingting

    2016-05-01

    This work is related to the combinatorial data analysis problem of seriation used for data visualization and exploratory analysis. Seriation re-sequences the data, so that more similar samples or objects appear closer together, whereas dissimilar ones are further apart. Despite the large number of current algorithms to realize such re-sequencing, there has not been a systematic way for analyzing the resulting sequences, comparing them, or fusing them to obtain a single unifying one. We propose a new positional proximity measure that evaluates the similarity of two arbitrary sequences based on their agreement on pairwise positional information of the sequenced objects. Furthermore, we present various statistical properties of this measure as well as its normalized version modeled as an instance of the generalized correlation coefficient. Based on this measure, we define a new procedure for consensus seriation that fuses multiple arbitrary sequences based on a quadratic assignment problem formulation and an efficient way of approximating its solution. We also derive theoretical links with other permutation distance functions and present their associated combinatorial optimization forms for consensus tasks. The utility of the proposed contributions is demonstrated through the comparison and fusion of multiple seriation algorithms we have implemented, using many real-world datasets from different application domains.

  4. Planning the FUSE Mission Using the SOVA Algorithm

    Science.gov (United States)

    Lanzi, James; Heatwole, Scott; Ward, Philip R.; Civeit, Thomas; Calvani, Humberto; Kruk, Jeffrey W.; Suchkov, Anatoly

    2011-01-01

    Three documents discuss the Sustainable Objective Valuation and Attainability (SOVA) algorithm and software as used to plan tasks (principally, scientific observations and associated maneuvers) for the Far Ultraviolet Spectroscopic Explorer (FUSE) satellite. SOVA is a means of managing risk in a complex system, based on a concept of computing the expected return value of a candidate ordered set of tasks as a product of pre-assigned task values and assessments of attainability made against qualitatively defined strategic objectives. For the FUSE mission, SOVA autonomously assembles a week-long schedule of target observations and associated maneuvers so as to maximize the expected scientific return value while keeping the satellite stable, managing the angular momentum of spacecraft attitude- control reaction wheels, and striving for other strategic objectives. A six-degree-of-freedom model of the spacecraft is used in simulating the tasks, and the attainability of a task is calculated at each step by use of strategic objectives as defined by use of fuzzy inference systems. SOVA utilizes a variant of a graph-search algorithm known as the A* search algorithm to assemble the tasks into a week-long target schedule, using the expected scientific return value to guide the search.

  5. Ball driven type MEMS SAD for artillery fuse

    Science.gov (United States)

    Seok, Jin Oh; Jeong, Ji-hun; Eom, Junseong; Lee, Seung S.; Lee, Chun Jae; Ryu, Sung Moon; Oh, Jong Soo

    2017-01-01

    The SAD (safety and arming device) is an indispensable fuse component that ensures safe and reliable performance during the use of ammunition. Because the application of electronic devices for smart munitions is increasing, miniaturization of the SAD has become one of the key issues for next-generation artillery fuses. Based on MEMS technology, various types of miniaturized SADs have been proposed and fabricated. However, none of them have been reported to have been used in actual munitions due to their lack of high impact endurance and complicated explosive train arrangements. In this research, a new MEMS SAD using a ball driven mechanism, is successfully demonstrated based on a UV LIGA (lithography, electroplating and molding) process. Unlike other MEMS SADs, both high impact endurance and simple structure were achieved by using a ball driven mechanism. The simple structural design also simplified the fabrication process and increased the processing yield. The ball driven type MEMS SAD performed successfully under the desired safe and arming conditions of a spin test and showed fine agreement with the FEM simulation result, conducted prior to its fabrication. A field test was also performed with a grenade launcher to evaluate the SAD performance in the firing environment. All 30 of the grenade samples equipped with the proposed MEMS SAD operated successfully under the high-G setback condition.

  6. Comparison of mechanical properties for polyamide 12 composite-based biomaterials fabricated by fused filament fabrication and injection molding

    Science.gov (United States)

    Rahim, Tuan Noraihan Azila Tuan; Abdullah, Abdul Manaf; Akil, Hazizan Md; Mohamad, Dasmawati

    2016-12-01

    The emergence of 3D printing technology known as fused filament fabrication (FFF) has offered the possibility of producing an anatomically accurate, patient specific implant with more affordable prices. The only weakness of this technology is related to incompatibility and lack of properties of current material to be applied in biomedical. Therefore, this study aims to develop a new, polymer composite-based biomaterial that exhibits a high processability using FFF technique, strong enough and shows acceptable biocompatibility, and safe for biomedical use. Polyamide 12 (PA12), which meets all these requirements was incorporated with two bioceramic fillers, zirconia and hydroxyapatite in order to improve the mechanical and bioactivity properties. The obtained mechanical properties were compared with injection-molded specimens and also a commercial biomedical product, HAPEXTM which is composed of hydroxyapatite and polyethylene. The yield strength and modulus of the PA12 composites increased steadily with increasing filler loading. Although the strength of printed PA12 composites were reduced compared with injection molded specimen, but still higher than HAPEXTM material. The higher surface roughness obtained by printed PA12 was expected to enhance the cell adhesion and provide better implant fixation.

  7. Zirconia implant abutments: microstructural analysis.

    Science.gov (United States)

    Vaquero-Aguilar, Cristina; Jiménez-Melendo, Manuel; Torres-Lagares, Daniel; Llena-Blasco, Oriol; Bruguera, August; Llena-Blasco, Jaime; García-Calderón, Manuel; Velázquez-Cayón, Rocío; Gutiérrez-Pérez, José-Luis

    2012-01-01

    Yttria-stabilized zirconia (ZrO₂-Y₂O₃) ceramics have received increasing attention in recent years because of their stress-induced tetragonal-to-monoclinic (martensitic) transformation. This unique process acts as a toughening mechanism, imparting strength and toughness to the ceramic alloy. This property, along with well-documented biocompatibility, is now being exploited in an increasing number of medical applications, including implant dentistry. To prevent clinical problems and predict their behavior and physical limitations, a characterization of the ceramic elements used in dental restorations is essential. The aim of the present study is to characterize the crystal structure, elemental composition, and micr ostructure of asreceived ZiReal Post (Biomet 3i) zirconium oxide abutments, as well as specimens coated with a first layer of a low-fusing fluoroapatite ceramic. Zirconium oxide abutments, both as-received and porcelain-coated, were studied using the following techniques: x-ray diffraction, x-ray fluorescence, energy dispersive x-ray spectroscopy, optical microscopy, and scanning and transmission electron microscopy. X-ray analyses detected only the presence of Zr, O, Y, and hafnium (Hf), in an amount of 3% to 4% molecular weight Y₂O₃-ZrO₂. X-ray diffraction measurements showed that the ceramic abutment crystallizes mainly in the tetragonal phase, with some residual monoclinic phase. The microstructure is characterized by a rather homogenous grain distribution, formed by equiaxed and fine grains with a mean size of 0.30 Μm. Compositional and diffraction results are consistent with polycrystalline yttria-stabilized tetragonal zirconia. The material is susceptible to undergoing the stress-induced transformation toughening mechanism because of the very fine grain size. Except for machining ring marks, the surfaces exhibit an excellent finishing quality. No structural modifications were observed in the fluoroapatite ceramic-coated abutments

  8. Analysis of postmarket complaints database for the iFuse SI Joint Fusion System®: a minimally invasive treatment for degenerative sacroiliitis and sacroiliac joint disruption

    Directory of Open Access Journals (Sweden)

    Miller LE

    2013-05-01

    Full Text Available Larry E Miller,1,2 W Carlton Reckling,3 Jon E Block21Miller Scientific Consulting Inc, Arden, NC, 2The Jon Block Group, San Francisco, CA, 3SI-BONE Inc, San Jose, CA, USABackground: The sacroiliac joint is a common but under-recognized source of low back and gluteal pain. Patients with degenerative sacroiliitis or sacroiliac joint disruption resistant to nonsurgical treatments may undergo open surgery with sacroiliac joint arthrodesis, although outcomes are mixed and risks are significant. Minimally invasive sacroiliac joint arthrodesis was developed to minimize the risk of iatrogenic injury and to improve patient outcomes compared with open surgery.Methods: Between April 2009 and January 2013, 5319 patients were treated with the iFuse SI Joint Fusion System® for conditions including sacroiliac joint disruption and degenerative sacroiliitis. A database was prospectively developed to record all complaints reported to the manufacturer in patients treated with the iFuse device. Complaints were collected through spontaneous reporting mechanisms in support of ongoing mandatory postmarket surveillance efforts.Results: Complaints were reported in 204 (3.8% patients treated with the iFuse system. Pain was the most commonly reported clinical complaint (n = 119, 2.2%, with nerve impingement (n = 48, 0.9% and recurrent sacroiliac joint pain (n = 43, 0.8% most frequently cited. All other clinical complaints were rare (≤0.2%. Ninety-six revision surgeries were performed in 94 (1.8% patients at a median follow-up of four (range 0–30 months. Revisions were typically performed in the early postoperative period for treatment of a symptomatic malpositioned implant (n = 46, 0.9% or to correct an improperly sized implant in an asymptomatic patient (n = 10, 0.2%. Revisions in the late postoperative period were performed to treat symptom recurrence (n = 34, 0.6% or for continued pain of undetermined etiology (n = 6, 0.1%.Conclusion: Analysis of a postmarket

  9. MUSIC AND COCHLEAR IMPLANTS

    Institute of Scientific and Technical Information of China (English)

    Mao Yitao; Xu Li

    2013-01-01

    Currently, most people with modern multichannel cochlear implant systems can understand speech in qui-et environment very well. However, studies in recent decades reported a lack of satisfaction in music percep-tion with cochlear implants. This article reviews the literature on music ability of cochlear implant users by presenting a systematic outline of the capabilities and limitations of cochlear implant recipients with regard to their music perception as well as production. The review also evaluates the similarities and differences be-tween electric hearing and acoustic hearing regarding music perception. We summarize the research results in terms of the individual components of music (e.g., rhythm, pitch, and timbre). Finally, we briefly intro-duce the vocal singing of prelingually-deafened children with cochlear implants as evaluated by acoustic measures.

  10. Benefits and Risks of Cochlear Implants

    Science.gov (United States)

    ... Prosthetics Cochlear Implants Benefits and Risks of Cochlear Implants Share Tweet Linkedin Pin it More sharing options ... Cochlear Implants What are the Benefits of Cochlear Implants? For people with implants: Hearing ranges from near ...

  11. Bone reactions adjacent to titanium implants subjected to static load of different duration. A study in the dog (III)

    DEFF Research Database (Denmark)

    Gotfredsen, K; Berglundh, T; Lindhe, J

    2001-01-01

    The aim of the present experiment was to study the effect of a long-standing lateral static load on the peri-implant bone. Three beagle dogs were used. The mandibular premolars were extracted and 12 weeks later 3 titanium implants (ITI(R) Dental Implant System) were installed in each quadrant....... Crowns were fitted to all implants 12 weeks after the installation procedure. The anterior and central crowns were fused and connected to the posterior crown by an expansion screw. In the right side of the mandible, the expansion screws were activated every 2 weeks during a 46-week period. During...... the last 10 weeks of this period, an expansion force similar to that of the right side was applied in the left. The animals were sacrificed and block biopsies of each implant site harvested and prepared for histological analysis. Sites subjected to 10 weeks or 46 weeks of lateral load had a similar (i...

  12. A one-kilogram quartz resonator as a mass standard.

    Science.gov (United States)

    Vig, John; Howe, David

    2013-02-01

    The SI unit of mass, the kilogram, is defined by a single artifact, the International Prototype Kilogram. This artifact, the primary mass standard, suffers from long-term instabilities that are neither well understood nor easily monitored. A secondary mass standard consisting of a 1-kg quartz resonator in ultrahigh vacuum is proposed. The frequency stability of such a resonator is likely to be far higher than the mass stability of the primary mass standard. Moreover, the resonator would provide a link to the SI time-interval unit. When compared with a laboratory-grade atomic frequency standard or GPS time, the frequency of the resonator could be monitored, on a continuous basis, with 10(-15) precision in only a few days of averaging. It could also be coordinated, worldwide, with other resonator mass standards without the need to transport the standards.

  13. Respiratory Monitoring by Porphyrin Modified Quartz Crystal Microbalance Sensors

    Directory of Open Access Journals (Sweden)

    Seung-Woo Lee

    2011-01-01

    Full Text Available A respiratory monitoring system based on a quartz crystal microbalance (QCM sensor with a functional film was designed and investigated. Porphyrins 5,10,15,20-tetrakis-(4-sulfophenyl-21H,23H-porphine (TSPP and 5,10,15,20-tetrakis-(4-sulfophenyl-21H, 23H-porphine manganese (III chloride (MnTSPP used as sensitive elements were assembled with a poly(diallyldimethyl ammonium chloride (PDDA. Films were deposited on the QCM resonators using layer-by-layer method in order to develop the sensor. The developed system, in which the sensor response reflects lung movements, was able to track human respiration providing respiratory rate (RR and respiratory pattern (RP. The sensor system was tested on healthy volunteers to compare RPs and calculate RRs. The operation principle of the proposed system is based on the fast adsorption/desorption behavior of water originated from human breath into the sensor films deposited on the QCM electrode.

  14. Polishing of quartz by rapid etching in ammonium bifluoride.

    Science.gov (United States)

    Vallin, Orjan; Danielsson, Rolf; Lindberg, Ulf; Thornell, Greger

    2007-07-01

    The etch rate and surface roughness of polished and lapped AT-cut quartz subjected to hot (90, 110, and 130 degrees C), concentrated (50, 65, 80 wt %) ammonium bi-fluoride have been investigated. Having used principal component analysis to verify experimental solidity and analyze data, we claim with confidence that this parameter space does not, as elsewhere stated, allow for a polishing effect or even a preserving setting. Etch rates were found to correlate well, and possibly logarithmically, with temperature except for the hottest etching applied to lapped material. Roughness as a function of temperature and concentration behaved well for the lapped material, but lacked systematic variation in the case of the polished material. At the lowest temperature, concentration had no effect on etch rate or roughness. Future efforts are targeted at temperatures and concentrations closer to the solubility limit.

  15. Manufacturing technology for high quality swept-culture growth quartz

    Science.gov (United States)

    Balascio, J. F.; Lias, N. C.

    1983-09-01

    Relatively low impurity alpha-quartz has been grown from the hydroxide mineralizer system with the use of three types of nutrient: converted, special cultured and cultured. The converted nutrient resulted in the lowest total ppm level (2.6) and Al ppm level (0.5) in the as-grown crystals. Special cultured and cultured nutrients resulted in 1.7 ppm and 2.1 ppm of aluminum in crystals grown, respectively, from these nutrients. Infrared Q values ranged from 2.5x10 to the 6th power in these crystals. With respect to rho in the as-grown crystals, a ten minute etching of seeds in 7.0 molal ammonium bifluoride has resulted in the growth of the lowest etch channel density crystals (approx = 135/sq cm).

  16. Petrophysical evaluation methods: basal quartz formation, Manyberries Area , Alberta

    Energy Technology Data Exchange (ETDEWEB)

    Davis, B.W.

    1980-01-01

    Hydrocarbons, both oil and gas, have been discovered in the basal quartz formation in the Manyberries area of SE Alberta. Estimation of producible fluids and hydrocarbons in place has been difficult due to the very shaly nature of the reservoir rock. Calculations of water saturation with no corrections for clay conductivity underestimates the hydrocarbons in place. The Waxman-Smits evaluation technique, which provides a method to account for clay conductivities, was used to estimate water saturation based on total porosity. Work of other authors provides a technique to correlate total and effective porosities. This was used to estimate effective porosity and subsequently water saturation based on the effective porosity. Error analysis was undertaken to estimate the uncertainty in the calculated water saturations.

  17. Detection of sulfur dioxide using a piezoelectric quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Guimaraes, O.M. [Instituto de Quimica de Sao Carlos (Brazil)

    1997-09-01

    Sulfur dioxide was detected and determined in air by a piezoelectric quartz crystal sensor coated with 4-aminoantipyrine/1-hydroxyetil-2-heptadecenyl imidazol (amine 220) solution (1:1 v/v in chloroform). The analytical response curve is linear over the concentration range from 0.70 to 5.0 ppm of SO{sub 2}. Good linearities (r = 0.9990, 0.9995 and 0.9968) and sensitivities (18.0, 33.4 and 50.7 Hz/ppm) were found, respectively for exposure times of 30, 60 and 90 seconds. The sensor can be used for more than six months without loss in sensitivity and presented good reversibility and reproducibility. Among some possible interferents tested, only nitrogen dioxide and moisture caused major frequency changes.

  18. Experimental microstylolites in quartz and modelling of natural stylolitic structures

    CERN Document Server

    Gratier, Jean-Pierre; Hassani, Riad; Renard, Francois

    2008-01-01

    Experimental microstylolites have been observed at stressed contacts between quartz grains loaded for several weeks in the presence of an aqueous silica solution, at 350 8C and 50 MPa of differential stress. Stereoscopic analysis of pairs of SEM images yielded a digital elevation model of the surface of the microstylolites. Fourier analyses of these microstylolites reveal a self-affine roughness (with a roughness exponent H of 1.2). Coupled with observations of close interactions between dissolution pits and stylolitic peaks, these data illustrate a possible mechanism for stylolite formation. The complex geometry of stylolite surfaces is imposed by the interplay between the development of dissolution peaks in preferential locations (fast dissolution pits) and the mechanical properties of the solid-fluid-solid interfaces. Simple mechanical modeling expresses the crucial competition that could rule the development of microstylolites: (i) a stress-related process, modeled in terms of the stiffness of springs tha...

  19. Quartz crystal microbalance and photoacoustic measurements in dental photocuring

    Science.gov (United States)

    Lima, Marcenilda A.; Bastos, Ivan N.; Cella, Norberto

    2016-09-01

    Photocured dental resins are used extensively in restorative procedures in dentistry. Inadequate curing reduces the lifetime of the dental restoration, and consequently it is essential to precisely measure the polymerisation kinetics. In this study, two techniques, Quartz Crystal Microbalance (QCM) and Photoacoustic Spectroscopy (PAS), were used to monitor the real-time cure and to obtain the optical absorption spectra of resins, respectively. From the PAS measurements, the precise peaks of absorption were identified, and were used as the appropriate wavelength of the photocuring light in the QCM monitoring. The combined use of these techniques allows reliable determination of the duration of the phases of physical and chemical changes that occur during photocuring. Two commercial dental resins were tested, and the results confirmed the advantages of using PAS and QCM to study polymerisation kinetics.

  20. Quartz-Enhanced Photoacoustic Spectroscopy with Right-Angle Prism

    Directory of Open Access Journals (Sweden)

    Yongning Liu

    2016-02-01

    Full Text Available A right-angle prism was used to enhance the acoustic signal of a quartz-enhanced photoacoustic spectroscopy (QEPAS system. The incident laser beam was parallelly inverted by the right-angle prism and passed through the gap between two tuning fork prongs again to produce another acoustic excitation. Correspondingly, two pairs of rigid metal tubes were used as acoustic resonators with resonance enhancement factors of 16 and 12, respectively. The QEPAS signal was enhanced by a factor of 22.4 compared with the original signal, which was acquired without resonators or a prism. In addition, the system noise was reduced a little with double resonators due to the Q factor decrease. The signal-to-noise ratio (SNR was greatly improved. Additionally, a normalized noise equivalent absorption coefficient (NNEA of 5.8 × 10−8 W·cm−1·Hz−1/2 was achieved for water vapor detection in the atmosphere.

  1. Testing the isotropy of space using rotating quartz oscillators

    CERN Document Server

    Lo, Anthony; Mizrachi, Eli; Anderegg, Loic; Müller, Holger; Hohensee, Michael; Goryachev, Maxim; Tobar, Michael E

    2014-01-01

    Violations of Lorentz invariance by matter and light can generate direction- and frame-dependent anisotropies in particles inertial masses and, hence, a measurable modulation of the oscillation frequency of rotating quartz crystal oscillators. This allows simple and low maintenance experiments that are ideally suited for long-term data taking. Using the Standard Model Extension (SME) as a parameterizing framework, we study the magnitude of this putative frequency modulation. A preliminary experiment with room-temperature SC-cut crystals yields a frequency resolution in the $10^{-15}$ range with $\\sim 120$ hours of data and a limit of $\\tilde c_Q=(-1.8 \\pm 2.2)\\times 10^{-14}$\\,GeV on the most weakly constrained neutron-sector $c-$coefficient of the SME. Future experiments with cryogenic oscillators promise additional improvements in accuracy, opening up the potential for improved tests of Lorentz symmetry in the neutron, proton, electron and photon sector.

  2. Seismic design or retrofit of buildings with metallic structural fuses by the damage-reduction spectrum

    Science.gov (United States)

    Li, Gang; Jiang, Yi; Zhang, Shuchuan; Zeng, Yan; Li, Qiang

    2015-03-01

    Recently, the structural fuse has become an important issue in the field of earthquake engineering. Due to the trilinearity of the pushover curve of buildings with metallic structural fuses, the mechanism of the structural fuse is investigated through the ductility equation of a single-degree-of-freedom system, and the corresponding damage-reduction spectrum is proposed to design and retrofit buildings. Furthermore, the controlling parameters, the stiffness ratio between the main frame and structural fuse and the ductility factor of the main frame, are parametrically studied, and it is shown that the structural fuse concept can be achieved by specific combinations of the controlling parameters based on the proposed damage-reduction spectrum. Finally, a design example and a retrofit example, variations of real engineering projects after the 2008 Wenchuan earthquake, are provided to demonstrate the effectiveness of the proposed design procedures using buckling restrained braces as the structural fuses.

  3. Carbothermal Reduction of Quartz with Carbon from Natural Gas

    Science.gov (United States)

    Li, Fei; Tangstad, Merete

    2017-04-01

    Carbothermal reaction between quartz and two different carbons originating from natural gas were investigated in this paper. One of two carbons is the commercial carbon black produced from natural gas in a medium thermal production process. The other carbon is obtained from natural gas cracking at 1273 K (1000 °C) deposited directly on the quartz pellet. At the 1923 K (1650 °C) and CO atmosphere, the impact of carbon content, pellet structure, gas transfer, and heating rate are investigated in a thermo-gravimetric furnace. The reaction process can be divided into two steps: an initial SiC-producing step followed by a SiO-producing step. Higher carbon content and increased gas transfer improves the reaction rate of SiC-producing step, while the thicker carbon coating in carbon-deposited pellet hinders reaction rate. Better gas transfer of sample holder improves reaction rate but causes more SiO loss. Heating rate has almost no influence on reaction. Mass balance analysis shows that mole ratios between SiO2, free carbon, and SiC in the SiC-producing step and SiO-producing step in CO and Ar fit the reaction SiO2(s) + 3 C(s) = SiC(s) + 2 CO(g). SiC-particle and SiC-coating formation process in mixed pellet and carbon-deposited pellet are proposed. SiC whiskers formed in the voids of these two types of pellets.

  4. Carbothermal Reduction of Quartz with Carbon from Natural Gas

    Science.gov (United States)

    Li, Fei; Tangstad, Merete

    2017-01-01

    Carbothermal reaction between quartz and two different carbons originating from natural gas were investigated in this paper. One of two carbons is the commercial carbon black produced from natural gas in a medium thermal production process. The other carbon is obtained from natural gas cracking at 1273 K (1000 °C) deposited directly on the quartz pellet. At the 1923 K (1650 °C) and CO atmosphere, the impact of carbon content, pellet structure, gas transfer, and heating rate are investigated in a thermo-gravimetric furnace. The reaction process can be divided into two steps: an initial SiC-producing step followed by a SiO-producing step. Higher carbon content and increased gas transfer improves the reaction rate of SiC-producing step, while the thicker carbon coating in carbon-deposited pellet hinders reaction rate. Better gas transfer of sample holder improves reaction rate but causes more SiO loss. Heating rate has almost no influence on reaction. Mass balance analysis shows that mole ratios between SiO2, free carbon, and SiC in the SiC-producing step and SiO-producing step in CO and Ar fit the reaction SiO2(s) + 3 C(s) = SiC(s) + 2 CO(g). SiC-particle and SiC-coating formation process in mixed pellet and carbon-deposited pellet are proposed. SiC whiskers formed in the voids of these two types of pellets.

  5. FUSE Observations of Comet C/2001 Q4 (NEAT)

    Science.gov (United States)

    Feldman, P. D.; Weaver, H. A.; Christian, D.; Combi, M. R.; Krasnopolsky, V.; Lisse, C. M.; Mumma, M. J.; Shemansky, D. E.; Stern, S. A.

    2004-11-01

    We report observations of comet C/2001 Q4 (NEAT) with the Far Ultraviolet Spectroscopic Explorer (FUSE) beginning 00:40 UT on 2004 April 24. This was the first moving target observation made by FUSE since the failure of two reaction wheels in December 2001. Spectra were obtained in the 905--1180 Å range at 0.3 Å spectral resolution using the 30'' × 30'' aperture and closely resemble the spectra of three comets observed in 2001 and reported previously. The principal features are the (0,0) bands of the CO Birge-Hopfield systems, atomic lines of \\ion{O}{1} and \\ion{H}{1}, and three lines of the H2 Lyman pumped by solar Lyman-β fluorescence. The CO C - X (0,0) band showed a nearly sinusoidal variation over the 27 hr observation interval with a period of 17.0 hr and a peak to minimum ratio of 1.56. The derived average CO production rate is Q(CO) = 8 × 1027 molecules s-1 which is about 4% that of H2O based on concurrent HST/STIS observations of OH emission. As in the previous observations, only upper limits are found for emission from \\ion{Ar}{1} and N2. A relatively strong feature near 1031.8 Å is most likely the H2 Werner (1,1) Q3 line pumped by solar \\ion{O}{6} and \\ion{N}{3}, as the corresponding lines in the (1,3) and (1,4) bands are also present. There may be evidence for weak \\ion{O}{6} emission at 1031.9 Å, in the wing of the H2 line, and at 1037.6 Å. The roughly two dozen other emissions that were not identified in the earlier spectra are also present in C/2001 Q4 at comparable strength to those in comet C/2001 A2 (LINEAR). As C/2001 A2 had a comparable water production rate to that of C/2001 Q4 at the time of observation, the source(s) of these emissions may be ubiquitous in comets. This work is based on data obtained by the NASA-CNES-CSA FUSE mission operated by The Johns Hopkins University. Financial support was partly provided by NASA contract NAS5-32985.

  6. Dental Implant Systems

    Science.gov (United States)

    Oshida, Yoshiki; Tuna, Elif B.; Aktören, Oya; Gençay, Koray

    2010-01-01

    Among various dental materials and their successful applications, a dental implant is a good example of the integrated system of science and technology involved in multiple disciplines including surface chemistry and physics, biomechanics, from macro-scale to nano-scale manufacturing technologies and surface engineering. As many other dental materials and devices, there are crucial requirements taken upon on dental implants systems, since surface of dental implants is directly in contact with vital hard/soft tissue and is subjected to chemical as well as mechanical bio-environments. Such requirements should, at least, include biological compatibility, mechanical compatibility, and morphological compatibility to surrounding vital tissues. In this review, based on carefully selected about 500 published articles, these requirements plus MRI compatibility are firstly reviewed, followed by surface texturing methods in details. Normally dental implants are placed to lost tooth/teeth location(s) in adult patients whose skeleton and bony growth have already completed. However, there are some controversial issues for placing dental implants in growing patients. This point has been, in most of dental articles, overlooked. This review, therefore, throws a deliberate sight on this point. Concluding this review, we are proposing a novel implant system that integrates materials science and up-dated surface technology to improve dental implant systems exhibiting bio- and mechano-functionalities. PMID:20480036

  7. Dental Implant Systems

    Directory of Open Access Journals (Sweden)

    Yoshiki Oshida

    2010-04-01

    Full Text Available Among various dental materials and their successful applications, a dental implant is a good example of the integrated system of science and technology involved in multiple disciplines including surface chemistry and physics, biomechanics, from macro-scale to nano-scale manufacturing technologies and surface engineering. As many other dental materials and devices, there are crucial requirements taken upon on dental implants systems, since surface of dental implants is directly in contact with vital hard/soft tissue and is subjected to chemical as well as mechanical bio-environments. Such requirements should, at least, include biological compatibility, mechanical compatibility, and morphological compatibility to surrounding vital tissues. In this review, based on carefully selected about 500 published articles, these requirements plus MRI compatibility are firstly reviewed, followed by surface texturing methods in details. Normally dental implants are placed to lost tooth/teeth location(s in adult patients whose skeleton and bony growth have already completed. However, there are some controversial issues for placing dental implants in growing patients. This point has been, in most of dental articles, overlooked. This review, therefore, throws a deliberate sight on this point. Concluding this review, we are proposing a novel implant system that integrates materials science and up-dated surface technology to improve dental implant systems exhibiting bio- and mechano-functionalities.

  8. Binaural fusion and listening effort in children who use bilateral cochlear implants: a psychoacoustic and pupillometric study.

    Science.gov (United States)

    Steel, Morrison M; Papsin, Blake C; Gordon, Karen A

    2015-01-01

    Bilateral cochlear implants aim to provide hearing to both ears for children who are deaf and promote binaural/spatial hearing. Benefits are limited by mismatched devices and unilaterally-driven development which could compromise the normal integration of left and right ear input. We thus asked whether children hear a fused image (ie. 1 vs 2 sounds) from their bilateral implants and if this "binaural fusion" reduces listening effort. Binaural fusion was assessed by asking 25 deaf children with cochlear implants and 24 peers with normal hearing whether they heard one or two sounds when listening to bilaterally presented acoustic click-trains/electric pulses (250 Hz trains of 36 ms presented at 1 Hz). Reaction times and pupillary changes were recorded simultaneously to measure listening effort. Bilaterally implanted children heard one image of bilateral input less frequently than normal hearing peers, particularly when intensity levels on each side were balanced. Binaural fusion declined as brainstem asymmetries increased and age at implantation decreased. Children implanted later had access to acoustic input prior to implantation due to progressive deterioration of hearing. Increases in both pupil diameter and reaction time occurred as perception of binaural fusion decreased. Results indicate that, without binaural level cues, children have difficulty fusing input from their bilateral implants to perceive one sound which costs them increased listening effort. Brainstem asymmetries exacerbate this issue. By contrast, later implantation, reflecting longer access to bilateral acoustic hearing, may have supported development of auditory pathways underlying binaural fusion. Improved integration of bilateral cochlear implant signals for children is required to improve their binaural hearing.

  9. Binaural fusion and listening effort in children who use bilateral cochlear implants: a psychoacoustic and pupillometric study.

    Directory of Open Access Journals (Sweden)

    Morrison M Steel

    Full Text Available Bilateral cochlear implants aim to provide hearing to both ears for children who are deaf and promote binaural/spatial hearing. Benefits are limited by mismatched devices and unilaterally-driven development which could compromise the normal integration of left and right ear input. We thus asked whether children hear a fused image (ie. 1 vs 2 sounds from their bilateral implants and if this "binaural fusion" reduces listening effort. Binaural fusion was assessed by asking 25 deaf children with cochlear implants and 24 peers with normal hearing whether they heard one or two sounds when listening to bilaterally presented acoustic click-trains/electric pulses (250 Hz trains of 36 ms presented at 1 Hz. Reaction times and pupillary changes were recorded simultaneously to measure listening effort. Bilaterally implanted children heard one image of bilateral input less frequently than normal hearing peers, particularly when intensity levels on each side were balanced. Binaural fusion declined as brainstem asymmetries increased and age at implantation decreased. Children implanted later had access to acoustic input prior to implantation due to progressive deterioration of hearing. Increases in both pupil diameter and reaction time occurred as perception of binaural fusion decreased. Results indicate that, without binaural level cues, children have difficulty fusing input from their bilateral implants to perceive one sound which costs them increased listening effort. Brainstem asymmetries exacerbate this issue. By contrast, later implantation, reflecting longer access to bilateral acoustic hearing, may have supported development of auditory pathways underlying binaural fusion. Improved integration of bilateral cochlear implant signals for children is required to improve their binaural hearing.

  10. Nanotechnology for dental implants.

    Science.gov (United States)

    Tomsia, Antoni P; Lee, Janice S; Wegst, Ulrike G K; Saiz, Eduardo

    2013-01-01

    With the advent of nanotechnology, an opportunity exists for the engineering of new dental implant materials. Metallic dental implants have been successfully used for decades, but they have shortcomings related to osseointegration and mechanical properties that do not match those of bone. Absent the development of an entirely new class of materials, faster osseointegration of currently available dental implants can be accomplished by various surface modifications. To date, there is no consensus regarding the preferred method(s) of implant surface modification, and further development will be required before the ideal implant surface can be created, let alone become available for clinical use. Current approaches can generally be categorized into three areas: ceramic coatings, surface functionalization, and patterning on the micro- to nanoscale. The distinctions among these are imprecise, as some or all of these approaches can be combined to improve in vivo implant performance. These surface improvements have resulted in durable implants with a high percentage of success and long-term function. Nanotechnology has provided another set of opportunities for the manipulation of implant surfaces in its capacity to mimic the surface topography formed by extracellular matrix components of natural tissue. The possibilities introduced by nanotechnology now permit the tailoring of implant chemistry and structure with an unprecedented degree of control. For the first time, tools are available that can be used to manipulate the physicochemical environment and monitor key cellular events at the molecular level. These new tools and capabilities will result in faster bone formation, reduced healing time, and rapid recovery to function.

  11. High-voltage safety fuses for the transition-radiation tracking detector in the ATLAS experiment

    CERN Document Server

    Voronov, S A; Onishchenko, E M; Simakov, A B; Sosnovtsev, V V; Suchkov, S; Sugrobova, T A

    2004-01-01

    A safety fuse has been designed for the electrical protection of gas- filled detectors in the ATLAS experiment at CERN (Geneva, Switzerland). The fuse is a polished lithium niobate plate with a titanium strip of 91-kOmega resistance deposited by the photolithographic technique. The forced blowout time of the fuse is 10-50 ms; whereupon the leakage current through it is less than 1 nA at a 2-kV voltage. The resistance of the fuse case is greater than or equivalent equal' greater than 10**1**2 Omega. Its overall dimensions are 5.8 multiplied by 3.8 multiplied by 2 mm.

  12. Development of Fuses for Protection of Geiger-Mode Avalanche Photodiode Arrays

    Science.gov (United States)

    Grzesik, Michael; Bailey, Robert; Mahan, Joe; Ampe, Jim

    2015-11-01

    Current-limiting fuses composed of Ti/Al/Ni were developed for use in Geiger-mode avalanche photodiode arrays for each individual pixel in the array. The fuses were designed to burn out at ˜4.5 × 10-3 A and maintain post-burnout leakage currents less than 10-7 A at 70 V sustained for several minutes. Experimental fuse data are presented and successful incorporation of the fuses into a 256 × 64 pixel InP-based Geiger-mode avalanche photodiode array is reported.

  13. Optimized condition for etching fused-silica phase gratings with inductively coupled plasma technology.

    Science.gov (United States)

    Wang, Shunquan; Zhou, Changhe; Ru, Huayi; Zhang, Yanyan

    2005-07-20

    Polymer deposition is a serious problem associated with the etching of fused silica by use of inductively coupled plasma (ICP) technology, and it usually prevents further etching. We report an optimized etching condition under which no polymer deposition will occur for etching fused silica with ICP technology. Under the optimized etching condition, surfaces of the fabricated fused silica gratings are smooth and clean. Etch rate of fused silica is relatively high, and it demonstrates a linear relation between etched depth and working time. Results of the diffraction of gratings fabricated under the optimized etching condition match theoretical results well.

  14. Threats to ICF reactor materials: computational simulations of radiation damage induced topological changes in fused silica

    CERN Document Server

    Kubota, A; Stolken, J; Sadigh, B; Reyes, S; Rubia, T D; Latkowski, J F

    2003-01-01

    We have performed molecular dynamics simulations of radiation damage in fused silica. In this study, we discuss the role of successive cascade overlap on the saturation and self-healing of oxygen vacancy defects in the amorphous fused silica network. Furthermore, we present findings on the topological changes in fused silica due to repeated energetic recoil atoms. These topological network modifications consistent with experimental Raman spectroscopic observation on neutron and ion irradiated fused silica are indicators of permanent densification that has also been observed experimentally.

  15. A Fused Maxillary Central Incisor and Its Multidisciplinary Treatment: An 18-Year Follow-Up

    Directory of Open Access Journals (Sweden)

    Lluís Brunet-Llobet

    2014-01-01

    Full Text Available Fused teeth may cause aesthetic, spacing, periodontal, eruption, and caries problems. The present case report describes a 7-year-old boy patient with a chief complaint of unerupted maxillary incisor. Radiographic examination indicated a fused tooth which had two fused roots but two independent root canals. A complex management of a fused tooth is really difficult to standardize. In this case an orthodontic, endodontic, and surgical treatment (intentional replantation allowed the tooth to be retained until 18 years following intervention. Maintenance of the root and alveolar bone in young adults at least until full skeletal maturation should be the main treatment objective.

  16. Retrospective dosimetry: Dose evaluation using unheated and heated quartz from a radioactive waste storage building

    DEFF Research Database (Denmark)

    Jain, M.; Bøtter-Jensen, L.; Murray, A.S.

    2002-01-01

    and particularly in nuclear installations. These materials contain natural dosemeters Such as quartz. which usually is less sensitive than its heated counterpart. The potential of quartz extracted from mortar in a wall of a low-level radioactive-waste storage facility containing distributed sources of Co-60 and Cs...

  17. Microbially induced separation of quartz from hematite using sulfate reducing bacteria.

    Science.gov (United States)

    Prakasan, M R Sabari; Natarajan, K A

    2010-07-01

    Cells and metabolic products of Desulfovibrio desulfuricans were successfully used to separate quartz from hematite through environmentally benign microbially induced flotation. Bacterial metabolic products such as extracellular proteins and polysaccharides were isolated from both unadapted and mineral-adapted bacterial metabolite and their basic characteristics were studied in order to get insight into the changes brought about on bioreagents during adaptation. Interaction between bacterial cells and metabolites with minerals like hematite and quartz brought about significant surface-chemical changes on both the minerals. Quartz was rendered more hydrophobic, while hematite became more hydrophilic after biotreatment. The predominance of bacterial polysaccharides on interacted hematite and of proteins on quartz was responsible for the above surface-chemical changes, as attested through adsorption studies. Surface-chemical changes were also observed on bacterial cells after adaptation to the above minerals. Selective separation of quartz from hematite was achieved through interaction with quartz-adapted bacterial cells and metabolite. Mineral-specific proteins secreted by quartz-adapted cells were responsible for conferment of hydrophobicity on quartz resulting in enhanced separation from hematite through flotation.

  18. Development of quartz particulate reinforced AA6063 aluminum matrix composites via friction stir processing

    Directory of Open Access Journals (Sweden)

    S. Joyson Abraham

    2016-12-01

    Full Text Available Friction stir processing (FSP has been accepted as a potential method to produce aluminum matrix composites (AMCs without the drawbacks of liquid metallurgy methods. The present work focuses on the development of AMCs reinforced with quartz (SiO2 particles using FSP. Grooves with various dimensions were machined on AA6063 plates and compacted with quartz particles. A single pass FSP was carried out using a combination of optimized process parameters. The volume fraction of quartz particles in the AMCs was varied from 0 to 18 vol.% in steps of 6 vol.%. The developed AA6063/Quartz AMCs were characterized using optical, scanning and transmission electron microscopy. The quartz particles were distributed uniformly in the aluminum matrix irrespective of the location within the stir zone. The grains of the AA6063 were extensively refined by the combination of thermomechanical effect of FSP and the pinning effect of quartz particles. The dispersion of the quartz particles improved the microhardness and wear resistance of the AMCs. The role of quartz particles on the worn surface and wear debris is reported.

  19. Testing the application of quartz and feldspar luminescence dating to MIS 5 Japanese marine deposits

    DEFF Research Database (Denmark)

    Thiel, Christine; Tsukamoto, Sumiko; Tokuyasu, Kayoko

    2015-01-01

    The applicability of both quartz and feldspar luminescence dating was tested on twenty-five samples from a marine succession now forming a coastal cliff at Oga Peninsula, Honshu Island, Japan. The quartz optically stimulated luminescence (OSL) signal shows thermal instability and linear modulated...

  20. Retrospective dosimetry using Japanese brick quartz: A way forward despite an unstable fast decaying OSL signal

    DEFF Research Database (Denmark)

    Fujita, Hiroki; Jain, Mayank; Murray, A.S.

    2011-01-01

    Quartz extracted from heated bricks has been previously suggested for use in dose estimation in accident dosimetry, but this technique has never been applied before to Japanese quartz which often has unusual OSL characteristics. In this study the optically stimulated luminescence (OSL) characteri...

  1. Effectiveness of a Multidimensional Randomized Control Intervention to Reduce Quartz Exposure Among Construction Workers

    NARCIS (Netherlands)

    Deurssen, E. van; Meijster, T; Oude Hengel, K.M.; Boessen, R.; Spaan, S.; Tielemans, E.; Heederik, D.; Pronk, A.

    2015-01-01

    There is little evidence with respect to the effectiveness of intervention programs that focus on the reduction of occupational quartz exposure in the construction industry. This article evaluates the effectiveness of a multidimensional intervention which was aimed at reducing occupational quartz

  2. Effectiveness of a Multidimensional Randomized Control Intervention to Reduce Quartz Exposure Among Construction Workers

    NARCIS (Netherlands)

    Deurssen, E. van; Meijster, T; Oude Hengel, K.M.; Boessen, R.; Spaan, S.; Tielemans, E.; Heederik, D.; Pronk, A.

    2015-01-01

    There is little evidence with respect to the effectiveness of intervention programs that focus on the reduction of occupational quartz exposure in the construction industry. This article evaluates the effectiveness of a multidimensional intervention which was aimed at reducing occupational quartz ex

  3. The Suitability Of Local Quartz Sand In The Production Of Bath Crucibles.

    Directory of Open Access Journals (Sweden)

    C. O. Okpanachi

    2015-08-01

    Full Text Available The suitability of local quartz sand in the production of bath crucibles is a study that was carried out in order to impart overall strength on bath crucibles hence reduce breakages during fettling. Therefore this research constitutes a study to enhance the efficiency of production of bath crucibles by addition of quartz sand in slip preparation. The steps taken in the beneficiation of quartz sand for the production of bath crucibles are comminution which entails crushing and milling classification washing liquid dispersion sizing and reduction of iron content by magnetic separation. The slip contains materials like plastic clay feldspar kaolin talc sodium silicate water quartz sand etc. These were all milled in the ball mill for slip production casting and fettling glazing and sintering to get final bath crucibles as the end products. Quartz sand is used in a variety of products essentially as raw material for the foundry casting and glass industries and also in chemicals water filtration and ceramics the heat resistance nature of quartz sand makes it an excellent refractory substance for these industrial processes. Slip can be prepared for production of bath crucibles without the inclusion of quartz sand however the addition of quartz sand is needed to improve the mechanical performance of the slip in the production of bath crucibles.

  4. 75 FR 12468 - Airworthiness Directives; Quartz Mountain Aerospace, Inc. Model 11E Airplanes

    Science.gov (United States)

    2010-03-16

    ... With the next 10 Follow Quartz aileron pushrod bearings. hours time-in- Mountain Aerospace service (TIS... aileron Within 50 hours TIS Follow Quartz pushrod bearings. after the cleaning Mountain Aerospace and... Aerospace, Inc. Model 11E Airplanes AGENCY: Federal Aviation Administration (FAA), Department...

  5. Luminescence property of volcanic quartz and the use of red isothermal TL for dating tephras

    DEFF Research Database (Denmark)

    Tsukamoto, S.; Murray, A.S.; Huot, S.

    2007-01-01

    An optically stimulated luminescence (OSL) age obtained from a Japanese tephra using quartz phenocrysts severely underestimated the known age. The characteristics of the OSL signals were investigated in order to understand the cause of the underestimation; the main OSL component of volcanic quartz...

  6. Optical dating of single sand-sized grains of quartz: Sources of variability

    DEFF Research Database (Denmark)

    Duller, G.A.T.; Bøtter-Jensen, L.; Murray, A.S.

    2000-01-01

    Optically stimulated luminescence (OSL) measurements have been made of over 3000 sand-sized grains of quartz. Analysis at this scale highlights the variability in the luminescence sensitivity and the dose saturation characteristics of individual quartz grains. Using a new instrument capable of me...... intensity, dose saturation characteristics and instrument uncertainty in equivalent dose calculation. (C) 2000 Elsevier Science Ltd. All rights reserved....

  7. Bioceramics for implant coatings

    Directory of Open Access Journals (Sweden)

    Allison A Campbell

    2003-11-01

    Early research in this field focused on understanding the biomechanical properties of metal implants, but recent work has turned toward improving the biological properties of these devices. This has led to the introduction of calcium phosphate (CaP bioceramics as a bioactive interface between the bulk metal impart and the surrounding tissue. The first CaP coatings were produced via vapor phase processes, but more recently solution-based and biomimetic methods have emerged. While each approach has its own intrinsic materials and biological properties, in general CaP coatings promise to improve implant biocompatibility and ultimately implant longevity.

  8. Delayed breast implant reconstruction

    DEFF Research Database (Denmark)

    Hvilsom, Gitte B.; Hölmich, Lisbet R.; Steding-Jessen, Marianne

    2011-01-01

    the period 1999 to 2006; 239 one-stage procedures and 353 two-stage procedures. The postoperative course through November 2009 was evaluated by cumulative incidence adjusting for competing risks for the selected outcomes; hematoma, infection, seroma, implant rupture, severe capsular contracture (modified.......7% for severe capsular contracture, 32.3% for displacement/asymmetry of the implant and 38.6% for reoperation. When comparing one- and two-stage procedures, we observed significantly higher risk estimates for infection, seroma and extrusion of the implant following two-stage procedures, whereas the risk...

  9. Biomedical implantable microelectronics.

    Science.gov (United States)

    Meindl, J D

    1980-10-17

    Innovative applications of microelectronics in new biomedical implantable instruments offer a singular opportunity for advances in medical research and practice because of two salient factors: (i) beyond all other types of biomedical instruments, implants exploit fully the inherent technical advantages--complex functional capability, high reliability, lower power drain, small size and weight-of microelectronics, and (ii) implants bring microelectronics into intimate association with biological systems. The combination of these two factors enables otherwise impossible new experiments to be conducted and new paostheses developed that will improve the quality of human life.

  10. Optimization of dental implantation

    Science.gov (United States)

    Dol, Aleksandr V.; Ivanov, Dmitriy V.

    2017-02-01

    Modern dentistry can not exist without dental implantation. This work is devoted to study of the "bone-implant" system and to optimization of dental prostheses installation. Modern non-invasive methods such as MRI an 3D-scanning as well as numerical calculations and 3D-prototyping allow to optimize all of stages of dental prosthetics. An integrated approach to the planning of implant surgery can significantly reduce the risk of complications in the first few days after treatment, and throughout the period of operation of the prosthesis.

  11. Control of Montmorillonite Surface Coatings on Quartz Grains in Bentonite by Precursor Volcanic Glass

    Science.gov (United States)

    Wendlandt, R. F.; Harrison, W. J.

    2008-12-01

    The pathogenic tendencies of respirable-sized quartz grains may be dependent on inherent characteristics of the quartz as well as external factors. Surface coatings on quartz are of particular interest as they modify both physical and chemical properties of quartz grain surfaces and sequester the grain from contact with reactive lung fluids. Wendlandt et al. (Appl. Geochem. 22, 2007) investigated the surface properties of respirable-sized quartz grains in bentonites and recognized pervasive montmorillonite surface coatings on the quartz that resisted removal by repeated vigorous washings and reaction with HCl. To understand the persistence of montmorillonite coatings on quartz grains of igneous origin, volcanic ash deposits of varying age and degree of alteration to montmorillonite were sampled in Utah, including the distal Lava Creek (c. 0.64 Ma) and Bishop Tuffs (c. 0.74 Ma), and SW Colorado (Conejos Fm, San Juan Volcanic Field) for comparison with commercial grade Cretaceous-age "western" and "southern" bentonites. Quartz grains, hand-picked from these samples, were analyzed using FE-SEM and HRTEM. Continuous coatings of volcanic glass occur on quartz grains from the distal volcanic ash samples. As glass alteration to montmorillonite becomes more extensive, quartz grain surfaces start to display patches of montmorillonite. These patches become continuous in extent on quartz grains from the bentonites. Late precipitation of opal- CT lepispheres is consistent with the alteration reaction for volcanic glass: Volcanic glass + H2O = montmorillonite + SiO2(am) + ions(aq). HRTEM of quartz grains reveals an amorphous surface layer, consistent with a volcanic glass coating. Our results indicate that persistent montmorillonite coatings on quartz grains in bentonites are related to precursor volcanic glass coatings on these grains. The absence of glass coatings on other mineral grains in bentonite (feldspar, biotite) may be a consequence of the presence of strong cleavage

  12. Note: Discharging fused silica test masses with ionized nitrogen

    Science.gov (United States)

    Ugolini, D.; Funk, Q.; Amen, T.

    2011-04-01

    We have developed a technique for discharging fused silica test masses in a gravitational-wave interferometer with nitrogen ionized by an electron beam. The electrons are produced from a heated filament by thermionic emission in a low-pressure region to avoid contamination and burnout. Some electrons then pass through a small aperture and ionize nitrogen in a higher-pressure region, and this ionized gas is pumped across the test mass surface, neutralizing both polarities of charge. The discharge rate varies exponentially with charge density and filament current, quadratically with filament potential, and has an optimal working pressure of ˜8 mT. Adapting the technique to larger test mass chambers is also discussed.

  13. Fusing Quantitative Requirements Analysis with Model-based Systems Engineering

    Science.gov (United States)

    Cornford, Steven L.; Feather, Martin S.; Heron, Vance A.; Jenkins, J. Steven

    2006-01-01

    A vision is presented for fusing quantitative requirements analysis with model-based systems engineering. This vision draws upon and combines emergent themes in the engineering milieu. "Requirements engineering" provides means to explicitly represent requirements (both functional and non-functional) as constraints and preferences on acceptable solutions, and emphasizes early-lifecycle review, analysis and verification of design and development plans. "Design by shopping" emphasizes revealing the space of options available from which to choose (without presuming that all selection criteria have previously been elicited), and provides means to make understandable the range of choices and their ramifications. "Model-based engineering" emphasizes the goal of utilizing a formal representation of all aspects of system design, from development through operations, and provides powerful tool suites that support the practical application of these principles. A first step prototype towards this vision is described, embodying the key capabilities. Illustrations, implications, further challenges and opportunities are outlined.

  14. Does oligomerization in fused thiophene affect reactivity and aromaticity?

    Indian Academy of Sciences (India)

    Siddhartha Kr Purkayastha; Pradip Kr Bhattacharyya

    2016-02-01

    Reactivity and aromaticity of a few fused thiophene oligomers and their conformers are discussed in the light of density functional theory (DFT) and conceptual density functional theory. Reactivity parameters, such as hardness () and electrophilicity (), chemical potential () and energy of the HOMO (highest occupied molecular orbital) have been studied. Oligomerization raises the HOMO of the species, which in turn increases the reactivity of the oligomers. The absorption spectra of the species are analysed using TDDFT (time dependent density functional theory). The absorption peaks show red shift with increasing size of the oligomers. Aromaticity of the species is gauged by nucleus independent chemical shift (NICS). The out-of-plane component, (NICSzz) values advocate higher aromatic character at longer distance whereas, NICS supports the reverse.

  15. Fused Adaptive Lasso for Spatial and Temporal Quantile Function Estimation

    KAUST Repository

    Sun, Ying

    2015-09-01

    Quantile functions are important in characterizing the entire probability distribution of a random variable, especially when the tail of a skewed distribution is of interest. This article introduces new quantile function estimators for spatial and temporal data with a fused adaptive Lasso penalty to accommodate the dependence in space and time. This method penalizes the difference among neighboring quantiles, hence it is desirable for applications with features ordered in time or space without replicated observations. The theoretical properties are investigated and the performances of the proposed methods are evaluated by simulations. The proposed method is applied to particulate matter (PM) data from the Community Multiscale Air Quality (CMAQ) model to characterize the upper quantiles, which are crucial for studying spatial association between PM concentrations and adverse human health effects. © 2016 American Statistical Association and the American Society for Quality.

  16. Loss of suppressor-of-fused function promotes tumorigenesis.

    Science.gov (United States)

    Lee, Y; Kawagoe, R; Sasai, K; Li, Y; Russell, H R; Curran, T; McKinnon, P J

    2007-09-27

    The Sonic Hedgehog (SHH) signaling pathway is indispensable for development, and functions to activate a transcriptional program modulated by the GLI transcription factors. Here, we report that loss of a regulator of the SHH pathway, Suppressor of Fused (Sufu), resulted in early embryonic lethality in the mouse similar to inactivation of another SHH regulator, Patched1 (Ptch1). In contrast to Ptch1+/- mice, Sufu+/- mice were not tumor prone. However, in conjunction with p53 loss, Sufu+/- animals developed tumors including medulloblastoma and rhabdomyosarcoma. Tumors present in Sufu+/-p53-/- animals resulted from Sufu loss of heterozygosity. Sufu+/-p53-/- medulloblastomas also expressed a signature gene expression profile typical of aberrant SHH signaling, including upregulation of N-myc, Sfrp1, Ptch2 and cyclin D1. Finally, the Smoothened inhibitor, hedgehog antagonist, did not block growth of tumors arising from Sufu inactivation. These data demonstrate that Sufu is essential for development and functions as a tumor suppressor.

  17. Fabrication of microchannels in fused silica using femtosecond Bessel beams

    Energy Technology Data Exchange (ETDEWEB)

    Yashunin, D. A., E-mail: yashuninda@yandex.ru [Institute of Applied Physics of the Russian Academy of Sciences, 46 Ulyanov Str., Nizhny Novgorod 603950 (Russian Federation); Nizhny Novgorod State Technical University, 24 Minin St., Nizhny Novgorod 603950 (Russian Federation); Malkov, Yu. A. [Institute of Applied Physics of the Russian Academy of Sciences, 46 Ulyanov Str., Nizhny Novgorod 603950 (Russian Federation); Mochalov, L. A.; Stepanov, A. N. [Institute of Applied Physics of the Russian Academy of Sciences, 46 Ulyanov Str., Nizhny Novgorod 603950 (Russian Federation); Nizhny Novgorod State Technical University, 24 Minin St., Nizhny Novgorod 603950 (Russian Federation); Lobachevsky State University of Nizhny Novgorod, 23 Gagarin Ave., Nizhny Novgorod 603950 (Russian Federation)

    2015-09-07

    Extended birefringent waveguiding microchannels up to 15 mm long were created inside fused silica by single-pulse irradiation with femtosecond Bessel beams. The birefringent refractive index change of 2–4 × 10{sup −4} is attributed to residual mechanical stress. The microchannels were chemically etched in KOH solution to produce 15 mm long microcapillaries with smooth walls and a high aspect ratio of 1:250. Bessel beams provide higher speed of material processing compared to conventional multipulse femtosecond laser micromachining techniques and permit simple control of the optical axis direction of the birefringent waveguides, which is important for practical applications [Corrielli et al., “Rotated waveplates in integrated waveguide optics,” Nat. Commun. 5, 4249 (2014)].

  18. Watermarking for Fused Deposition Modeling by Seam Placement

    Directory of Open Access Journals (Sweden)

    Baumann Felix W.

    2017-01-01

    Full Text Available With the increased usage and application of 3D-printing or Additive Manufacturing (AM the question arises of how content providers or creators can ensure their intellectual property on such model data. Similar to other digital media such object information that is represented in a number of file formats is easy to copy and reproduce lossless. This research contributes by a proposition of a watermarking schema for Fused Deposition Modeling (FDM type 3D-printers. This system embeds information into the 3D-printed object without alterations to the structure or geometry by altering the entry points of each layer in a specific manner. With such a watermarking schema employed objects can be embedded with additional information such as a serial number or other traceable information.

  19. Characterization of the polishing induced contamination of fused silica optics

    Science.gov (United States)

    Pfiffer, Mathilde; Longuet, Jean-Louis; Labrugère, Christine; Fargin, Evelyne; Bousquet, Bruno; Dussauze, Marc; Lambert, Sébastien; Cormont, Philippe; Néauport, Jérôme

    2016-12-01

    Secondary Ion Mass Spectroscopy (SIMS), Electron Probe Micro Analysis (EPMA) and X-Ray Photoelectron Spectroscopy (XPS) were used to analyze the polishing induced contamination layer at the fused silica optics surface. Samples were prepared using an MRF polishing machine and cerium-based slurry. The cerium and iron penetration and concentration were measured in the surface out of defects. Cerium is embedded at the surface in a 60 nm layer and concentrated at 1200 ppmw in this layer while iron concentration falls down at 30 nm. Spatial distribution and homogeneity of the pollution were also studied in scratches and bevel using SIMS and EPMA techniques. An overconcentration was observed in the chamfer and we saw evidence that surface defects such as scratches are specific places that hold the pollutants. A wet etching was able to completely remove the contamination in the scratch.

  20. Fusing Quantitative Requirements Analysis with Model-based Systems Engineering

    Science.gov (United States)

    Cornford, Steven L.; Feather, Martin S.; Heron, Vance A.; Jenkins, J. Steven

    2006-01-01

    A vision is presented for fusing quantitative requirements analysis with model-based systems engineering. This vision draws upon and combines emergent themes in the engineering milieu. "Requirements engineering" provides means to explicitly represent requirements (both functional and non-functional) as constraints and preferences on acceptable solutions, and emphasizes early-lifecycle review, analysis and verification of design and development plans. "Design by shopping" emphasizes revealing the space of options available from which to choose (without presuming that all selection criteria have previously been elicited), and provides means to make understandable the range of choices and their ramifications. "Model-based engineering" emphasizes the goal of utilizing a formal representation of all aspects of system design, from development through operations, and provides powerful tool suites that support the practical application of these principles. A first step prototype towards this vision is described, embodying the key capabilities. Illustrations, implications, further challenges and opportunities are outlined.

  1. Facade model refinement by fusing terrestrial laser data and image

    Science.gov (United States)

    Liu, Yawen; Qin, Sushun

    2015-12-01

    The building facade model is one of main landscapes of a city and basic data of city geographic information. It is widely useful in accurate path planning, real navigation through the urban environment, location-based application, etc. In this paper, a method of facade model refinement by fusing terrestrial laser data and image is presented. It uses the matching of model edge and image line combined with laser data verification and effectively refines facade geometry model that reconstructed from laser data. The laser data of geometric structures on building facade such as window, balcony and door are segmented, and used as a constraint for further selecting the optical model edges that are located at the cross-line of point data and no data. The results demonstrate the deviation of model edges caused by laser sampling interval can be removed in the proposed method.

  2. Development of 170 MHz Electrodeless Quartz-Crystal Microbalance Immunosensor with Nonspecifically Immobilized Receptor Proteins

    Science.gov (United States)

    Ogi, Hirotsugu; Nagai, Hironao; Fukunishi, Yuji; Yanagida, Taiji; Hirao, Masahiko; Nishiyama, Masayoshi

    2010-07-01

    Staphylococcus aureus protein A (SPA) shows high nonspecific binding affinity on a naked quartz surface, and it can be used as the receptor protein for detecting immunoglobulin G (IgG), the most important immunoglobulin. The immunosensor ability, however, significantly depends on the immobilization procedure. In this work, the effect of the nonspecific immobilization procedure on the sensor sensitivity is studied using a home-built electrodeless quartz-crystal microbalance (QCM) biosensor. The pure-shear vibration of a 9.7-µm-thick AT-cut quartz plate is excited and detected in liquids by the line antenna located outside the flow channel. SPA molecules are immobilized on the quartz surfaces, and human IgG is injected to monitor the binding reaction between SPA and IgG. This study reveals that a long (nearly 24 h) immersion procedure is required for immobilizing SPA to achieve the tight biding with the quartz surfaces.

  3. Flotation of quartz using N- (2-aminoethyl)-octadecanamide as collector

    Institute of Scientific and Technical Information of China (English)

    赵世民

    2003-01-01

    The flotation behavior of quartz using N-(2-aminoethyl)-octadecanamide (AEOA) as a collector was investigated. Zeta potential and infrared spectra were conducted to investigate the mechanism of the interaction of the quartz surface with the collector molecules. The results show that electrostatic force and hydrogen bond play an important role in governing the mechanism of flotation in acidic and alkaline media. The recoveries of quartz are 99.0%-99.8% in the pH range of 3-11. The recovery of quartz is less dependent on AEOA concentration, mainly due to the formation of micellae in aqueous solution,and the adsorption density of AEOA on the quartz surface nearly remains constant.

  4. Using conceptual spaces to fuse knowledge from heterogeneous robot platforms

    Science.gov (United States)

    Kira, Zsolt

    2010-04-01

    As robots become more common, it becomes increasingly useful for many applications to use them in teams that sense the world in a distributed manner. In such situations, the robots or a central control center must communicate and fuse information received from multiple sources. A key challenge for this problem is perceptual heterogeneity, where the sensors, perceptual representations, and training instances used by the robots differ dramatically. In this paper, we use Gärdenfors' conceptual spaces, a geometric representation with strong roots in cognitive science and psychology, in order to represent the appearance of objects and show how the problem of heterogeneity can be intuitively explored by looking at the situation where multiple robots differ in their conceptual spaces at different levels. To bridge low-level sensory differences, we abstract raw sensory data into properties (such as color or texture categories), represented as Gaussian Mixture Models, and demonstrate that this facilitates both individual learning and the fusion of concepts between robots. Concepts (e.g. objects) are represented as a fuzzy mixture of these properties. We then treat the problem where the conceptual spaces of two robots differ and they only share a subset of these properties. In this case, we use joint interaction and statistical metrics to determine which properties are shared. Finally, we show how conceptual spaces can handle the combination of such missing properties when fusing concepts received from different robots. We demonstrate the fusion of information in real-robot experiments with a Mobile Robots Amigobot and Pioneer 2DX with significantly different cameras and (on one robot) a SICK lidar.ÿÿÿÿ

  5. Thermal annealing of laser damage precursors on fused silica surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Shen, N; Miller, P E; Bude, J D; Laurence, T A; Suratwala, T I; Steele, W A; Feit, M D; Wang, L L

    2012-03-19

    Previous studies have identified two significant precursors of laser damage on fused silica surfaces at fluenes below {approx} 35 J/cm{sup 2}, photoactive impurities in the polishing layer and surface fractures. In the present work, isothermal heating is studied as a means of remediating the highly absorptive, defect structure associated with surface fractures. A series of Vickers indentations were applied to silica surfaces at loads between 0.5N and 10N creating fracture networks between {approx} 10{micro}m and {approx} 50{micro}m in diameter. The indentations were characterized prior to and following thermal annealing under various times and temperature conditions using confocal time-resolved photo-luminescence (CTP) imaging, and R/1 optical damage testing with 3ns, 355nm laser pulses. Significant improvements in the damage thresholds, together with corresponding reductions in CTP intensity, were observed at temperatures well below the glass transition temperature (T{sub g}). For example, the damage threshold on 05.N indentations which typically initiates at fluences <8 J/cm{sup 2} could be improved >35 J/cm{sup 2} through the use of a {approx} 750 C thermal treatment. Larger fracture networks required longer or higher temperature treatment to achieve similar results. At an annealing temperature > 1100 C, optical microscopy indicates morphological changes in some of the fracture structure of indentations, although remnants of the original fracture and significant deformation was still observed after thermal annealing. This study demonstrates the potential of using isothermal annealing as a means of improving the laser damage resistance of fused silica optical components. Similarly, it provides a means of further understanding the physics associated with optical damage and related mitigation processes.

  6. Case retrieval in medical databases by fusing heterogeneous information.

    Science.gov (United States)

    Quellec, Gwénolé; Lamard, Mathieu; Cazuguel, Guy; Roux, Christian; Cochener, Béatrice

    2011-01-01

    A novel content-based heterogeneous information retrieval framework, particularly well suited to browse medical databases and support new generation computer aided diagnosis (CADx) systems, is presented in this paper. It was designed to retrieve possibly incomplete documents, consisting of several images and semantic information, from a database; more complex data types such as videos can also be included in the framework. The proposed retrieval method relies on image processing, in order to characterize each individual image in a document by their digital content, and information fusion. Once the available images in a query document are characterized, a degree of match, between the query document and each reference document stored in the database, is defined for each attribute (an image feature or a metadata). A Bayesian network is used to recover missing information if need be. Finally, two novel information fusion methods are proposed to combine these degrees of match, in order to rank the reference documents by decreasing relevance for the query. In the first method, the degrees of match are fused by the Bayesian network itself. In the second method, they are fused by the Dezert-Smarandache theory: the second approach lets us model our confidence in each source of information (i.e., each attribute) and take it into account in the fusion process for a better retrieval performance. The proposed methods were applied to two heterogeneous medical databases, a diabetic retinopathy database and a mammography screening database, for computer aided diagnosis. Precisions at five of 0.809 ± 0.158 and 0.821 ± 0.177, respectively, were obtained for these two databases, which is very promising.

  7. FUSE Spectroscopy of the Accreting Hot Components in Symbiotic Variables

    Science.gov (United States)

    Sion, Edward M.; Godon, Patrick; Mikolajewska, Joanna; Sabra, Bassem; Kolobow, Craig

    2017-04-01

    We have conducted a spectroscopic analysis of the far-ultraviolet archival spectra of four symbiotic variables, EG And, AE Ara, CQ Dra, and RW Hya. RW Hya and EG And have never had a recorded outburst, while CQ Dra and AE Ara have outburst histories. We analyze these systems while they are in quiescence in order to help reveal the physical properties of their hot components via comparisons of the observations with optically thick accretion disk models and non-LTE model white dwarf photospheres. We have extended the wavelength coverage down to the Lyman limit with Far Ultraviolet Spectroscopic Explorer (FUSE) spectra. We find that the hot component in RW Hya is a low-mass white dwarf with a surface temperature of 160,000 K. We reexamine whether or not the symbiotic system CQ Dra is a triple system with a red giant transferring matter to a hot component made up of a cataclysmic variable in which the white dwarf has a surface temperature as low as ∼20,000 K. The very small size of the hot component contributing to the shortest wavelengths of the FUSE spectrum of CQ Dra agrees with an optically thick and geometrically thin (∼4% of the WD surface) hot (∼120,000 K) boundary layer. Our analysis of EG And reveals that its hot component is a hot, bare, low-mass white dwarf with a surface temperature of 80,000–95,000 K, with a surface gravity {log}(g)=7.5. For AE Ara, we also find that a low-gravity ({log}(g)∼ 6), hot (T∼ {{130,000}} K) WD accounts for the hot component.

  8. Characteristics Of Fused Couplers Below Cut-Off

    Science.gov (United States)

    Meyer, T. J.; Tekippe, V. J.

    1989-02-01

    A number of different architectures are being explored for the utilization of optical fiber in the subscriber loop. In addition to reliability and maintainability, cost is a prime consideration since full implementation of fiber in the local loop will not occur until it is economically viable. It is becoming increasingly clear that in order to accommodate a number of ISDN applications, including high definition television (HDTV), singlemode fiber with a singlemode laser at the terminal end will be required. The situation at the subscriber end is quite different, however. The data rates are expected to be low on the return path to allow for POTS ( plain old telephone service) and some data transfer. When this requirement is combined with cost and reliability considerations, the inexpensive lasers developed for the CD (compact disk) market become quite attractive. The biggest disadvantage of this source is that the fiber which is optimized for singlemode operation at 1300nm tends to be multimode in the 800nm band where these lasers operate. Previous papers have considered such effects as modal noise and pulse dispersion when using these lasers with fiber that is singlemode in the 1300nm band.[1] Another consideration is the passive components required to implement such an architecture. Figure 1 shows a typical bidirectional design with full duplex operation on a single fiber. The key component is the 800/1300 wavelength division multiplexer/demultiplexer (WDM). Because of the multimode nature of the fiber in the 800nm band, all fiber approaches to fabricating the WDM, such as the fused beconical taper (FBT) approach, raise new issues which are not encountered, for example, with 1300/1500nm WDM's.[2] In this paper we discuss the effects of the multimode behavior of the fiber on the performance of fused couplers and WDM's.

  9. Interaction of aluminum projectiles with quartz sand in impact experiments: Formation of khatyrkite (CuAl2) and reduction of SiO2 to Si

    Science.gov (United States)

    Hamann, Christopher; Stöffler, Dieter; Reimold, Wolf Uwe

    2016-11-01

    We analyzed the interaction of spherical, 6.36-mm-diameter, Cu-bearing aluminum projectiles with quartz sand targets in hypervelocity impact experiments performed at NASA Ames Vertical Gun Range. Impact velocities and inferred peak shock pressures varied between 5.9 and 6.5 km/s and ∼41 and 48 GPa, respectively. Shocked particles ("impact melt particles") coated with thin crusts of molten projectile material were recovered from the floors of the ca. 33-cm-diameter craters and the respective ejecta blankets. Through petrographic and chemical (optical microscopy, FE-EMPA, SEM-EDX, and XRF) analysis we show that these particles have a layered structure manifested in distinct layers of decreasing shock metamorphism. These can be characterized by the following physical and chemical reactions and alteration products: (i) complete melting and subsequent recrystallization of the projectile, forming a distinct crystallization texture in the fused metal crust; (ii) projectile-target mixing, involving a redox reaction between Cu-bearing Al alloy und SiO2, leading to formation of khatyrkite (CuAl2), Al2O3 melt, euhedral silicon crystals, and spherical droplets of silicon; (iii) melting of quartz to lechatelierite and formation of planar deformation features in relic quartz grains; and (iv) shock lithification of quartz grains with fracturing of grains, grain-boundary melting, planar deformation features, and complete loss of porosity. To our knowledge, this is the first report of khatyrkite formed experimentally in hypervelocity impact experiments. These results have implications for the understanding of a similar redox reaction between Al-Cu metal and siliceous impact melt recently postulated for the Khatyrka CV3 carbonaceous chondrite. Moreover, these results bear on the processes that lead to layers of regolith on the surfaces of planetary bodies without atmospheres, such as asteroids in the main belt (e.g., 4 Vesta), and on the Moon. Specifically, impacts of mm

  10. DEALING WITH DENTAL IMPLANT FAILURES

    Science.gov (United States)

    Levin, Liran

    2008-01-01

    An implant-supported restoration offers a predictable treatment for tooth replacement. Reported success rates for dental implants are high. Nevertheless, failures that mandate immediate implant removal do occur. The consequences of implant removal jeopardize the clinician's efforts to accomplish satisfactory function and esthetics. For the patient, this usually involves further cost and additional procedures. The aim of this paper is to describe different methods and treatment modalities to deal with dental implant failure. The main topics for discussion include identifying the failing implant, implants replacing failed implants at the exact site, and the use of other restorative options. When an implant fails, a tailor made treatment plan should be provided to each patient according to all relevant variables. Patients should be informed regarding all possible treatment modalities following implant failure and give their consent to the most appropriate treatment option for them. PMID:19089213

  11. Dealing with dental implant failures

    Directory of Open Access Journals (Sweden)

    Liran Levin

    2008-06-01

    Full Text Available An implant-supported restoration offers a predictable treatment for tooth replacement. Reported success rates for dental implants are high. Nevertheless, failures that mandate immediate implant removal do occur. The consequences of implant removal jeopardize the clinician's efforts to accomplish satisfactory function and esthetics. For the patient, this usually involves further cost and additional procedures. The aim of this paper is to describe different methods and treatment modalities to deal with dental implant failure. The main topics for discussion include identifying the failing implant, implants replacing failed implants at the exact site, and the use of other restorative options.When an implant fails, a tailor made treatment plan should be provided to each patient according to all relevant variables. Patients should be informed regarding all possible treatment modalities following implant failure and give their consent to the most appropriate treatment option for them.

  12. The toxicity of lead to Desulfovibrio desulfuricans G20 in the presence of goethite and quartz

    Energy Technology Data Exchange (ETDEWEB)

    Sani, Rajesh K.; Rastogi, Gurdeep; Moberly, J.; Dohnalkova, Alice; Ginn, Timothy R.; Spycher, Nicolas; Shende, Rajesh; Peyton, Brent

    2010-04-01

    An aqueous mixture of goethite, quartz, and lead chloride (PbCl2) was treated with the sulfatereducing bacterium, Desulfovibrio desulfuricans G20 (D. desulfuricans G20), in a medium specifically designed to assess metal toxicity. In the presence of 26 μM of soluble Pb, together with the goethite and quartz, D. desulfuricans G20 grew after a lag time of 5 days compared to 2 days in Pb-, goethite-, and quartz-free treatments. In the absence of goethite and quartz, however, with 26 μM soluble Pb, no measurable growth was observed. Results showed that D. desulfuricans G20 first removed Pb from solutions then growth began resulting in black precipitates of Pb and iron sulfides. Transmission electron microscopic analyses of thin sections of D. desulfuricans G20 treated with 10 μM PbCl2 in goethite- and quartz-free treatment showed the presence of a dense deposit of lead sulfide precipitates both in the periplasm and cytoplasm. However, thin sections of D. desulfuricans G20 treated with goethite, quartz, and PbCl2 (26 μM soluble Pb) showed the presence of a dense deposit of iron sulfide precipitates both in the periplasm and cytoplasm. Energy-dispersive X-ray spectroscopy, selected area electron diffraction patterns, or X-ray diffraction analyses confirmed the structure of precipitated Pb inside the cell as galena (PbS) in goethite- and quartz-free treatments, and iron sulfides in treatments with goethite, quartz, and PbCl2. Overall results suggest that even at the same soluble Pb concentration (26 μM), in the presence of goethite and quartz, apparent Pb toxicity to D. desulfuricans G20 decreased significantly. Further, accumulation of lead/iron sulfides inside D. desulfuricans G20 cells depended on the presence of goethite and quartz.

  13. Superelastic Orthopedic Implant Coatings

    Science.gov (United States)

    Fournier, Eric; Devaney, Robert; Palmer, Matthew; Kramer, Joshua; El Khaja, Ragheb; Fonte, Matthew

    2014-07-01

    The demand for hip and knee replacement surgery is substantial and growing. Unfortunately, most joint replacement surgeries will fail within 10-25 years, thereby requiring an arduous, painful, and expensive revision surgery. To address this issue, a novel orthopedic implant coating material ("eXalt") has been developed. eXalt is comprised of super elastic nitinol wire that is knit into a three-dimensional spacer fabric structure. eXalt expands in vivo to conform to the implantation site and is porous to allow for bone ingrowth. The safety and efficacy of eXalt were evaluated through structural analysis, mechanical testing, and a rabbit implantation model. The results demonstrate that eXalt meets or exceeds the performance of current coating technologies with reduced micromotion, improved osseointegration, and stronger implant fixation in vivo.

  14. MEMS biomedical implants

    Institute of Scientific and Technical Information of China (English)

    Tai Yuchong

    2012-01-01

    The field of micro-electro-mechanical systems (MEMS) has advanced tremendously for the last 20 years. Most commercially noticeably, the field has successfully advanced from pressure sensors to micro physical sensors, such as accelerometers and gyros, for handheld electronics application. In parallel, MEMS has also advanced into micro total analysis system(TAS) and/or lab-on-a-chip applications. This article would discuss a relatively new but promising future direction towards MEMS biomedical implants. Specifically, Parylene C has been explored to be used as a good MEMS implant material and will be discussed in detail. Demonstrated implant devices, such as retinal and spinal cord implants, are presented in this article.

  15. Risks of Breast Implants

    Science.gov (United States)

    ... an infection or injury. Demonstrated by redness, swelling, warmth, pain and or/loss of function. Lymphedema or ... Overfilling or underfilling of saline-filled breast implants Physical stresses such as trauma or intense physical pressure ...

  16. Cochlear Implant in Adults

    Directory of Open Access Journals (Sweden)

    Jaleh Samadi

    2003-09-01

    Full Text Available Cochlear implant is the result of a great combination and collaboration of engineering and medicine. It is mainly because it has the most conflict with the human nervous system among all prosthesis. Cochlear implant helps a child with profound hearing loss to understand and articulate speech and let an adult person with hearing loss communicate with people by phone. Although these wonderful results could not be seen in all patients, will let us know about the great scientific findings.

  17. A desymmetrization route to fused Troger's base analogues: synthesis, isolation, and characterization of the first anti-anti diastereomer of a fused tris-Troger's base analogue.

    Science.gov (United States)

    Hansson, Anna; Wixe, Torbjörn; Bergquist, Karl-Erik; Wärnmark, Kenneth

    2005-05-12

    A desymmetrization route to fused Troger's base analogues was developed. In this way, the synthesis of the first example of an anti-anti diastereomer of a fused tris-Troger's base analogue was accomplished. The resulting compound 5b is a nonlinear symmetric regioisomer obtained from p-bromoaniline in 7% yield. The corresponding syn-anti diastereomer 5a was obtained in 4% yield.

  18. The effect of crystal-plastic deformation on Ti concentration in quartz

    Science.gov (United States)

    Nachlas, W. O.; Hirth, G.; Whitney, D. L.; Teyssier, C. P.

    2013-12-01

    Quartz is a dominant phase controlling crustal rheology and strain localization, and the sensitivity of its recrystallization mechanisms to variations in temperature, pressure, and fluid activity make evaluation of these parameters crucial to reconstructing the deformation history of quartz-bearing rocks in the lithosphere. The advent of Ti in quartz thermobarometry provides a technique with potentially powerful applications for understanding the conditions at which rocks deform plastically in the crust. However, it is unclear how ductile deformation, specifically dislocation creep, affects Ti substitution in quartz and whether the Ti concentration in quartz accurately records the conditions at which quartz recrystallized. This study addresses these questions through a series of high P-T rock deformation experiments on precisely synthesized Ti-doped quartz aggregates to investigate the influence of strain and dynamic recrystallization on the concentration of Ti in quartz. Laboratory rock deformation experiments provide an ideal opportunity to study Ti solubility in deformed quartz because they allow for recrystallization to occur in a controlled environment; deformation experiments are conducted under isothermal and isobaric conditions at constant strain rate for increasing intervals of time to isolate the effect of strain on Ti chemistry of quartz. This study employs a novel doping synthesis method to produce a quartz aggregate consisting of a large population of quartz crystals doped with a precise Ti concentration where each individual crystal has a uniform dopant distribution. Deformation of a homogeneous starting material enables simulation of a retrograde solubility path, in which a sample with an initially high, uniform concentration is modified during deformation at conditions where the solubility is substantially lower. This enables observations to be made of the mechanisms responsible for mobilizing Ti through diffusion and exsolution to adjust to the

  19. Anodized dental implant surface

    Directory of Open Access Journals (Sweden)

    Sunil Kumar Mishra

    2017-01-01

    Full Text Available Purpose: Anodized implants with moderately rough surface were introduced around 2000. Whether these implants enhanced biologic effect to improve the environment for better osseointegration was unclear. The purpose of this article was to review the literature available on anodized surface in terms of their clinical success rate and bone response in patients till now. Materials and Methods: A broad electronic search of MEDLINE and PubMed databases was performed. A focus was made on peer-reviewed dental journals. Only articles related to anodized implants were included. Both animal and human studies were included. Results: The initial search of articles resulted in 581 articles on anodized implants. The initial screening of titles and abstracts resulted in 112 full-text papers; 40 animal studies, 16 studies on cell adhesion and bacterial adhesion onto anodized surfaced implants, and 47 human studies were included. Nine studies, which do not fulfill the inclusion criteria, were excluded. Conclusions: The long-term studies on anodized surface implants do favor the surface, but in most of the studies, anodized surface is compared with that of machined surface, but not with other surfaces commercially available. Anodized surface in terms of clinical success rate in cases of compromised bone and immediately extracted sockets has shown favorable success.

  20. Biomaterials in cochlear implants

    Directory of Open Access Journals (Sweden)

    Lenarz, Thomas

    2009-01-01

    Full Text Available The cochlear implant (CI represents, for almost 25 years now, the gold standard in the treatment of children born deaf and for postlingually deafened adults. These devices thus constitute the greatest success story in the field of ‘neurobionic’ prostheses. Their (now routine fitting in adults, and especially in young children and even babies, places exacting demands on these implants, particularly with regard to the biocompatibility of a CI’s surface components. Furthermore, certain parts of the implant face considerable mechanical challenges, such as the need for the electrode array to be flexible and resistant to breakage, and for the implant casing to be able to withstand external forces. As these implants are in the immediate vicinity of the middle-ear mucosa and of the junction to the perilymph of the cochlea, the risk exists – at least in principle – that bacteria may spread along the electrode array into the cochlea. The wide-ranging requirements made of the CI in terms of biocompatibility and the electrode mechanism mean that there is still further scope – despite the fact that CIs are already technically highly sophisticated – for ongoing improvements to the properties of these implants and their constituent materials, thus enhancing the effectiveness of these devices. This paper will therefore discuss fundamental material aspects of CIs as well as the potential for their future development.

  1. Anodized dental implant surface.

    Science.gov (United States)

    Mishra, Sunil Kumar; Kumar, Muktadar Anand; Chowdhary, Ramesh

    2017-01-01

    Anodized implants with moderately rough surface were introduced around 2000. Whether these implants enhanced biologic effect to improve the environment for better osseointegration was unclear. The purpose of this article was to review the literature available on anodized surface in terms of their clinical success rate and bone response in patients till now. A broad electronic search of MEDLINE and PubMed databases was performed. A focus was made on peer-reviewed dental journals. Only articles related to anodized implants were included. Both animal and human studies were included. The initial search of articles resulted in 581 articles on anodized implants. The initial screening of titles and abstracts resulted in 112 full-text papers; 40 animal studies, 16 studies on cell adhesion and bacterial adhesion onto anodized surfaced implants, and 47 human studies were included. Nine studies, which do not fulfill the inclusion criteria, were excluded. The long-term studies on anodized surface implants do favor the surface, but in most of the studies, anodized surface is compared with that of machined surface, but not with other surfaces commercially available. Anodized surface in terms of clinical success rate in cases of compromised bone and immediately extracted sockets has shown favorable success.

  2. Contraceptive implants: current perspectives

    Directory of Open Access Journals (Sweden)

    Rowlands S

    2014-09-01

    Full Text Available Sam Rowlands,1,2 Stephen Searle3 1Centre of Postgraduate Medical Research and Education, School of Health and Social Care, Bournemouth University, Bournemouth, United Kingdom; 2Dorset HealthCare, Bournemouth, United Kingdom; 3Sexual Health Services, Chesterfield, United KingdomAbstract: Progestin-only contraceptive implants are a highly cost-effective form of long-acting reversible contraception. They are the most effective reversible contraceptives and are of a similar effectiveness to sterilization. Pregnancies are rare in women using this method of contraception, and those that do occur must be fully investigated, with an ultrasound scan of the arm and serum etonogestrel level if the implant cannot be located. There are very few contraindications to use of implants, and they have an excellent safety profile. Both acceptability and continuation with the method are high. Noncontraceptive benefits include improvements in dysmenorrhea, ovulatory pain, and endometriosis. Problematic bleeding is a relatively common adverse effect that must be covered in preinsertion information-giving and supported adequately if it occurs. Recognized training for both insertion and removal should be undertaken. Care needs to be taken at both insertion and removal to avoid neurovascular injury. Implants should always be palpable; if they are not, noninsertion should be assumed until disproven. Etonogestrel implants are now radiopaque, which aids localization. Anticipated difficult removals should be performed by specially trained experts. Keywords: contraceptive, subdermal implant, etonogestrel, levonorgestrel, progestin-only, long-acting reversible contraception

  3. Biocompatible implant surface treatments.

    Science.gov (United States)

    Pattanaik, Bikash; Pawar, Sudhir; Pattanaik, Seema

    2012-01-01

    Surface plays a crucial role in biological interactions. Surface treatments have been applied to metallic biomaterials in order to improve their wear properties, corrosion resistance, and biocompatibility. A systematic review was performed on studies investigating the effects of implant surface treatments on biocompatibility. We searched the literature using PubMed, electronic databases from 1990 to 2009. Key words such as implant surface topography, surface roughness, surface treatment, surface characteristics, and surface coatings were used. The search was restricted to English language articles published from 1990 to December 2009. Additionally, a manual search in the major dental implant journals was performed. When considering studies, clinical studies were preferred followed by histological human studies, animal studies, and in vitro studies. A total of 115 articles were selected after elimination: clinical studies, 24; human histomorphometric studies, 11; animal histomorphometric studies, 46; in vitro studies, 34. The following observations were made in this review: · The focus has shifted from surface roughness to surface chemistry and a combination of chemical manipulations on the porous structure. More investigations are done regarding surface coatings. · Bone response to almost all the surface treatments was favorable. · Future trend is focused on the development of osteogenic implant surfaces. Limitation of this study is that we tried to give a broader overview related to implant surface treatments. It does not give any conclusion regarding the best biocompatible implant surface treatment investigated till date. Unfortunately, the eventually selected studies were too heterogeneous for inference of data.

  4. Image fusion techniques in permanent seed implantation

    Directory of Open Access Journals (Sweden)

    Alfredo Polo

    2010-10-01

    Full Text Available Over the last twenty years major software and hardware developments in brachytherapy treatment planning, intraoperative navigation and dose delivery have been made. Image-guided brachytherapy has emerged as the ultimate conformal radiation therapy, allowing precise dose deposition on small volumes under direct image visualization. In thisprocess imaging plays a central role and novel imaging techniques are being developed (PET, MRI-MRS and power Doppler US imaging are among them, creating a new paradigm (dose-guided brachytherapy, where imaging is used to map the exact coordinates of the tumour cells, and to guide applicator insertion to the correct position. Each of these modalities has limitations providing all of the physical and geometric information required for the brachytherapy workflow.Therefore, image fusion can be used as a solution in order to take full advantage of the information from each modality in treatment planning, intraoperative navigation, dose delivery, verification and follow-up of interstitial irradiation.Image fusion, understood as the visualization of any morphological volume (i.e. US, CT, MRI together with an additional second morpholo gical volume (i.e. CT, MRI or functional dataset (functional MRI, SPECT, PET, is a well known method for treatment planning, verification and follow-up of interstitial irradiation. The term image fusion is used when multiple patient image datasets are registered and overlaid or merged to provide additional information. Fused images may be created from multiple images from the same imaging modality taken at different moments (multi-temporalapproach, or by combining information from multiple modalities. Quality means that the fused images should provide additional information to the brachythe rapy process (diagnosis and staging, treatment planning, intraoperative imaging, treatment delivery and follow-up that cannot be obtained in other ways. In this review I will focus on the role of

  5. One-pot synthesis of 2-aryl-1,2-fused pyrimidones

    Indian Academy of Sciences (India)

    SAMIKANNU RAMESH; PON SARAVANAKUMAR; RAMASAMY DURAISAMY; ARVIND MATHUR; PIRAMA NAYAGAM ARUNACHALAM

    2017-03-01

    A facile and versatile method for the synthesis of alicyclic fused pyrimidones from aminoacrylates and lactams in the presence of phosphorous oxychloride is described. The results suggest that this method is widely applicable except for cyclobutyl fused systems. This method gives better yield than the method ofcondensing aminopyrrolidines with the beta keto esters.

  6. Using MERIS fused images for land-cover mapping vegetation status assessment in heterogeneous landscapes

    NARCIS (Netherlands)

    Zurita Milla, R.; Clevers, J.G.P.W.; Gijsel, J.A.E.; Schaepman, M.E.

    2011-01-01

    In this paper we evaluate the potential of ENVISAT–Medium Resolution Imaging Spectrometer (MERIS) fused images for land-cover mapping and vegetation status assessment in heterogeneous landscapes. A series of MERIS fused images (15 spectral bands; 25 m pixel size) is created using the linear mixing m

  7. Analysis of adjacent segment degeneration with laminectomy above a fused lumbar segment.

    Science.gov (United States)

    Gard, Andrew P; Klopper, Hendrik B; Doran, Stephen E; Hellbusch, Leslie C

    2013-11-01

    Although recent data suggests that lumbar fusion with decompression contributes to some marginal acceleration of adjacent segment degeneration (ASD), few studies have evaluated whether it is safe to perform a laminectomy above a fused segment. This study investigates the hypothesis that laminectomy above a fused lumbar segment does not increase the incidence of ASD, and assesses the benefits and risks of performing a laminectomy above a lumbar fusion. A retrospective review of 171 patients who underwent decompression and instrumented fusion of the lumbar spine was performed to analyze the association between ASD and laminectomy above the fused lumbar segment. Patients were divided into two groups - one group with instrumented fusion alone and the other group with instrumented fusion plus laminectomy above the fused segment. Of the 171 patients, 34 underwent additional decompressive laminectomy above the fused segment. There was a significant increase in ASD incidence as well as progression of ASD grade in both groups. There was no significant increase in ASD in patients with decompressive laminectomy above the fused lumbar segment compared to patients with laminectomy limited to the fused segment. This retrospective review of 171 patients who underwent decompression and instrumented fusion with follow-up radiographs demonstrates that laminectomy decompression above a fused segment does not significantly increase radiographic ASD. There is, however, a significant increase in ASD over time, which was observed throughout the entire cohort likely representing a natural progression of lumbar spondylosis above the fusion segment.

  8. 31 CFR 100.12 - Exchange of fused and mixed coins.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Exchange of fused and mixed coins. 100.12 Section 100.12 Money and Finance: Treasury Regulations Relating to Money and Finance EXCHANGE OF PAPER CURRENCY AND COIN Exchange of Coin § 100.12 Exchange of fused and mixed coins....

  9. High-voltage safety fuses for the transition-radiation tracking detector in the ATLAS experiment

    NARCIS (Netherlands)

    Voronov, SA; Voronov, YA; Onishchenko, EM; Simakov, AB; Sosnovtsev, VV; Suchkov, SI; Sugrobova, TA

    2004-01-01

    A safety fuse has been designed for the electrical protection of gas-filled detectors in the ATLAS experiment at CERN (Geneva, Switzerland). The fuse is a polished lithium niobate plate with a titanium strip of 91-kOmega resistance deposited by the photolithographic technique. The forced blow-out ti

  10. Ultrasensitive quartz crystal microbalance integrated with carbon nanotubes

    Science.gov (United States)

    Goyal, Abhijat

    In this thesis, an ultrasensitive Quartz Crystal Microbalance (QCM) which can be configured as a versatile (bio)chemical sensor is presented. The high sensitivity of the QCM was achieved via miniaturization using micromachining techniques. The absolute mass sensitivity of sensor was increased by decreasing the thickness and the area of the electrodes of the resonators. Through optimal design, microfabrication, and miniaturization the mass sensitivity of the sensors was increased by more than four orders of magnitude to less than 1 pg/Hz; as compared to 17 ng/Hz for commercially available 5 MHz bulk resonators. Miniaturization of the resonators enables their fabrication in an array format with each pixel of the array being individually addressed. This enables true spatial and temporal mass sensing capabilities. The fabricated resonators were tested for operation in air and water and high quality factors of 7500 and ˜2000 were obtained respectively. A dielectric etch process was developed to achieve the miniaturization of the sensors. The optimization of the dielectric etch process was achieved using statistical techniques such as Design of Experiment (DOE). An etch rate of 0.5 microm/min at rms surface roughness of less than 2 nm was achieved after the optimization process. The process parameters, namely the ICP power, the substrate power, the flow rate of gases, the operating pressure of the etch tool, distance of substrate holder from the source, and the temperature of substrate holder, were quantitatively related to the etch rate and rms surface roughness using least square fit to the etch data. The QCMs were integrated with carbon nanotubes using a simple spray-on technique. It was found that the addition of carbon nanotubes onto the electroded surface of the resonator increased its Q-factor by as much as 100%. It was proposed that the carbon nanotubes due to their high stiffness suppress the out-of-plane flexural vibrations in the QCMs thereby suppressing an

  11. Quartz Microbalance Sensor for the Detection of Acrylamide

    Directory of Open Access Journals (Sweden)

    Christoph A. Schalley

    2004-10-01

    Full Text Available Abstract: Several macrocycles of the Hunter-Vögtle type have been identified as superior host compounds for the detection of small amounts of acrylamide. When coated onto the surface of a quartz microbalance, these compounds serve as highly sensitive and selective sensor-active layers for their use in electronic noses. In this study, differently substituted macrocycles were investigated including an open-chain analogue and a catenane. Their structure and functional groups are correlated with their observed affinities to acrylamide and related acids and amides. The much smaller response of the open-chain compound and the almost absent sensor response of the catenane suggest that binding occurs within the cavity of the macrocycle. Theoretical calculations agree well with the experimental data even though they do not yet take into account the arrangement of the macrocycles in the sensor-active layer. The lower detection limit of acrylamide is 10 parts per billion (ppb, which is impressively low for this type of sensor. Other related compounds such as acrylic acid, propionamide, or propionic acid show no or significantly lower affinities to the macrocycles in these concentration ranges.

  12. Acoustic Tests of Lorentz Symmetry Using Quartz Oscillators

    Directory of Open Access Journals (Sweden)

    Anthony Lo

    2016-02-01

    Full Text Available We propose and demonstrate a test of Lorentz symmetry based on new, compact, and reliable quartz oscillator technology. Violations of Lorentz invariance in the matter and photon sector of the standard model extension generate anisotropies in particles’ inertial masses and the elastic constants of solids, giving rise to measurable anisotropies in the resonance frequencies of acoustic modes in solids. A first realization of such a “phonon-sector” test of Lorentz symmetry using room-temperature stress-compensated-cut crystals yields 120 h of data at a frequency resolution of 2.4×10^{−15} and a limit of c[over ˜]_{Q}^{n}=(−1.8±2.2×10^{−14}  GeV on the most weakly constrained neutron-sector c coefficient of the standard model extension. Future experiments with cryogenic oscillators promise significant improvements in accuracy, opening up the potential for improved limits on Lorentz violation in the neutron, proton, electron, and photon sector.

  13. COMMENT: Comment on `Inhomogeneities and birefringence in quartz'

    Science.gov (United States)

    Saint-Grégoire, P.; Luk'yanchuk, I.

    1999-10-01

    We comment on the role of the novel incommensurate elongated-triangle (ELT) phase in the huge light scattering in quartz at small angles that was observed more than 40 years ago at the icons/Journals/Common/alpha" ALT="alpha" ALIGN="TOP"/>-icons/Journals/Common/beta" ALT="beta" ALIGN="TOP"/> phase transition and was associated with optical inhomogeneities of unknown nature. The relation of these inhomogeneities with the differently oriented ferroelastic blocks of the ELT phase proposed by us and co-workers in a previous publication was misinterpreted and criticized in a recent article by Aslanyan et al (Aslanyan T E, Shigenari T and Abe K 1998 J. Phys.: Condens. Matter 10 4577), who claimed also that the lock-in occurs at qicons/Journals/Common/neq" ALT="neq" ALIGN="TOP"/>0. Responding to their criticism, we claim that the ELT blocks do have ferroelastic properties which induce the inhomogeneities of optical indices and that the lock-in occurs at q = 0.

  14. Molecular Imprinting Technology in Quartz Crystal Microbalance (QCM) Sensors.

    Science.gov (United States)

    Emir Diltemiz, Sibel; Keçili, Rüstem; Ersöz, Arzu; Say, Rıdvan

    2017-02-24

    Molecularly imprinted polymers (MIPs) as artificial antibodies have received considerable scientific attention in the past years in the field of (bio)sensors since they have unique features that distinguish them from natural antibodies such as robustness, multiple binding sites, low cost, facile preparation and high stability under extreme operation conditions (higher pH and temperature values, etc.). On the other hand, the Quartz Crystal Microbalance (QCM) is an analytical tool based on the measurement of small mass changes on the sensor surface. QCM sensors are practical and convenient monitoring tools because of their specificity, sensitivity, high accuracy, stability and reproducibility. QCM devices are highly suitable for converting the recognition process achieved using MIP-based memories into a sensor signal. Therefore, the combination of a QCM and MIPs as synthetic receptors enhances the sensitivity through MIP process-based multiplexed binding sites using size, 3D-shape and chemical function having molecular memories of the prepared sensor system toward the target compound to be detected. This review aims to highlight and summarize the recent progress and studies in the field of (bio)sensor systems based on QCMs combined with molecular imprinting technology.

  15. Molecular Imprinting Technology in Quartz Crystal Microbalance (QCM Sensors

    Directory of Open Access Journals (Sweden)

    Sibel Emir Diltemiz

    2017-02-01

    Full Text Available Molecularly imprinted polymers (MIPs as artificial antibodies have received considerable scientific attention in the past years in the field of (biosensors since they have unique features that distinguish them from natural antibodies such as robustness, multiple binding sites, low cost, facile preparation and high stability under extreme operation conditions (higher pH and temperature values, etc.. On the other hand, the Quartz Crystal Microbalance (QCM is an analytical tool based on the measurement of small mass changes on the sensor surface. QCM sensors are practical and convenient monitoring tools because of their specificity, sensitivity, high accuracy, stability and reproducibility. QCM devices are highly suitable for converting the recognition process achieved using MIP-based memories into a sensor signal. Therefore, the combination of a QCM and MIPs as synthetic receptors enhances the sensitivity through MIP process-based multiplexed binding sites using size, 3D-shape and chemical function having molecular memories of the prepared sensor system toward the target compound to be detected. This review aims to highlight and summarize the recent progress and studies in the field of (biosensor systems based on QCMs combined with molecular imprinting technology.

  16. Can enantiomorphic crystals like quartz play a role in the origin of homochirality on earth?

    Science.gov (United States)

    Klabunovskii, E I

    2001-01-01

    This communication reviews the possible actions of enantiomorphic crystals on the surface of Earth as sources of homochirality of organic compounds. The discovery of asymmetric adsorption and asymmetric catalysis involving optically active quartz crystals has led some authors to conclude that this source of asymmetry played an important role as a source of homochirality in nature, a concept that later proved erroneous. Moreover, data regarding the preponderance in nature of l-quartz crystals have been used to confirm calculations of the parity violation energy difference (PVED) for l-quartz and, hence, to explain the prevalence of L-amino acids and D-sugars in living matter. As discussed here, quartz and other enantiomorphs such as sodium chlorate can produce chiral intermediates active in autocatalytical processes. Our most recent compilation of the literature, however, reveals that the distribution of d- and l-quartz crystals at the surface of the Earth when all possible locations are included is quite random. Although quartz can serve as an effective asymmetric inductor in autocatalytic processes, it cannot be the source of homochirality of living matter because of the random occurrence of the two types of enantiomorphs. The calculations of PVED values for quartz therefore lack a sound physical basis.

  17. Neutrophil-derived ROS contribute to oxidative DNA damage induction by quartz particles.

    Science.gov (United States)

    van Berlo, Damien; Wessels, Anton; Boots, Agnes W; Wilhelmi, Verena; Scherbart, Agnes M; Gerloff, Kirsten; van Schooten, Frederik J; Albrecht, Catrin; Schins, Roel P F

    2010-12-01

    The carcinogenicity of respirable quartz is considered to be driven by reactive oxygen species (ROS) generation in association with chronic inflammation. The contribution of phagocyte-derived ROS to inflammation, oxidative stress, and DNA damage responses was investigated in the lungs of C57BL/6J wild-type and p47(phox-/-) mice, 24h after pharyngeal aspiration of DQ12 quartz (100 mg/kg bw). Bone-marrow-derived neutrophils from wild-type and p47(phox-/-) mice were used for parallel in vitro investigations in coculture with A549 human alveolar epithelial cells. Quartz induced a marked neutrophil influx in both wild-type and p47(phox-/-) mouse lungs. Significant increases in mRNA expression of the oxidative stress markers HO-1 and γ-GCS were observed only in quartz-treated wild-type animals. Oxidative DNA damage in lung tissue was not affected by quartz exposure and did not differ between p47(phox-/-) and WT mice. Differences in mRNA expression of the DNA repair genes OGG1, APE-1, DNA Polβ, and XRCC1 were also absent. Quartz treatment of cocultures containing wild-type neutrophils, but not p47(phox-/-) neutrophils, caused increased oxidative DNA damage in epithelial cells. Our study demonstrates that neutrophil-derived ROS significantly contribute to pulmonary oxidative stress responses after acute quartz exposure, yet their role in the associated induction of oxidative DNA damage could be shown only in vitro.

  18. Additive surface complexation modeling of uranium(VI) adsorption onto quartz-sand dominated sediments.

    Science.gov (United States)

    Dong, Wenming; Wan, Jiamin

    2014-06-17

    Many aquifers contaminated by U(VI)-containing acidic plumes are composed predominantly of quartz-sand sediments. The F-Area of the Savannah River Site (SRS) in South Carolina (USA) is an example. To predict U(VI) mobility and natural attenuation, we conducted U(VI) adsorption experiments using the F-Area plume sediments and reference quartz, goethite, and kaolinite. The sediments are composed of ∼96% quartz-sand and 3-4% fine fractions of kaolinite and goethite. We developed a new humic acid adsorption method for determining the relative surface area abundances of goethite and kaolinite in the fine fractions. This method is expected to be applicable to many other binary mineral pairs, and allows successful application of the component additivity (CA) approach based surface complexation modeling (SCM) at the SRS F-Area and other similar aquifers. Our experimental results indicate that quartz has stronger U(VI) adsorption ability per unit surface area than goethite and kaolinite at pH ≤ 4.0. Our modeling results indicate that the binary (goethite/kaolinite) CA-SCM under-predicts U(VI) adsorption to the quartz-sand dominated sediments at pH ≤ 4.0. The new ternary (quartz/goethite/kaolinite) CA-SCM provides excellent predictions. The contributions of quartz-sand, kaolinite, and goethite to U(VI) adsorption and the potential influences of dissolved Al, Si, and Fe are also discussed.

  19. The influence of various occlusal materials on stresses transferred to implant-supported prostheses and supporting bone: a three-dimensional finite-element study.

    Science.gov (United States)

    Sevimay, Mujde; Usumez, Aslihan; Eskitascioglu, Gurcan

    2005-04-01

    The aim of this numerical analysis was to evaluate the amount and localization of stress that occurs with various materials used in implant-crown design under functional forces. Computer-aided design techniques and a finite-element stress analysis method were used for evaluation. A 4.1 x 10-mm implant placed in the mandibular second premolar area was simulated and analyzed. Simulation and analysis were performed with the use of COSMOS/M software and Pro/Engineer 2000i on a Dual Pentium III 1-GHz computer. Crown designs were as follows: porcelain fused to noble metal crown, porcelain fused to base metal crown, In-Ceram porcelain crown, and IPS Empress 2 porcelain crown. A 300-N vertical force was applied to the centric relation stop points of the crowns. The results of this study indicated that different types of restorative materials play an important role in the amount and distribution of the stresses in the superstructure and the implant. The highest stress values were observed in the IPS Empress 2 porcelain crown design (600 MPa). Porcelain fused to base metal and In-Ceram framework designs transferred less stress to abutment. Type of restorative materials used in implant crown designs are significant factors in the amount and distribution of the stresses on superstructure and implant under functional forces. Porcelain fused to base metal (149 MPa) and In-Ceram (173 MPa) crown designs induced higher von Mises stress values within the framework than porcelain fused to noble metal (108 MPa) and IPS Empress 2 (119 MPa) porcelain crown designs.

  20. Refractive index sensors based on the fused tapered special multi-mode fiber

    Science.gov (United States)

    Fu, Xing-hu; Xiu, Yan-li; Liu, Qin; Xie, Hai-yang; Yang, Chuan-qing; Zhang, Shun-yang; Fu, Guang-wei; Bi, Wei-hong

    2016-01-01

    In this paper, a novel refractive index (RI) sensor is proposed based on the fused tapered special multi-mode fiber (SMMF). Firstly, a section of SMMF is spliced between two single-mode fibers (SMFs). Then, the SMMF is processed by a fused tapering machine, and a tapered fiber structure is fabricated. Finally, a fused tapered SMMF sensor is obtained for measuring external RI. The RI sensing mechanism of tapered SMMF sensor is analyzed in detail. For different fused tapering lengths, the experimental results show that the RI sensitivity can be up to 444.517 81 nm/RIU in the RI range of 1.334 9—1.347 0. The RI sensitivity is increased with the increase of fused tapering length. Moreover, it has many advantages, including high sensitivity, compact structure, fast response and wide application range. So it can be used to measure the solution concentration in the fields of biochemistry, health care and food processing.

  1. CalFUSE v3: A Data-Reduction Pipeline for the Far Ultraviolet Spectroscopic Explorer

    CERN Document Server

    Dixon, W V; Barrett, P E; Civeit, T; Dupuis, J; Fullerton, A W; Godard, B; Hsu, J C; Kaiser, M E; Kruk, J W; Lacour, S; Lindler, D J; Massa, D; Robinson, R D; Romelfanger, M L; Sonnentrucker, P

    2007-01-01

    Since its launch in 1999, the Far Ultraviolet Spectroscopic Explorer (FUSE) has made over 4600 observations of some 2500 individual targets. The data are reduced by the Principal Investigator team at the Johns Hopkins University and archived at the Multimission Archive at Space Telescope (MAST). The data-reduction software package, called CalFUSE, has evolved considerably over the lifetime of the mission. The entire FUSE data set has recently been reprocessed with CalFUSE v3.2, the latest version of this software. This paper describes CalFUSE v3.2, the instrument calibrations upon which it is based, and the format of the resulting calibrated data files.

  2. Inhibition of the mitochondrial respiratory chain function abrogates quartz induced DNA damage in lung epithelial cells

    Energy Technology Data Exchange (ETDEWEB)

    Li Hui [Institut fuer umweltmedizinische Forschung (IUF) at the Heinrich-Heine-University, Auf' m Hennekamp 50, D-40225 Duesseldorf (Germany); Haberzettl, Petra [Institut fuer umweltmedizinische Forschung (IUF) at the Heinrich-Heine-University, Auf' m Hennekamp 50, D-40225 Duesseldorf (Germany); Albrecht, Catrin [Institut fuer umweltmedizinische Forschung (IUF) at the Heinrich-Heine-University, Auf' m Hennekamp 50, D-40225 Duesseldorf (Germany); Hoehr, Doris [Institut fuer umweltmedizinische Forschung (IUF) at the Heinrich-Heine-University, Auf' m Hennekamp 50, D-40225 Duesseldorf (Germany); Knaapen, Ad M. [Department of Health Risk Analysis and Toxicology, Nutrition and Toxicology Research Institute Maastricht (NUTRIM), University of Maastricht (Netherlands); Borm, Paul J.A. [Institut fuer umweltmedizinische Forschung (IUF) at the Heinrich-Heine-University, Auf' m Hennekamp 50, D-40225 Duesseldorf (Germany); Hogeschool Zuyd Heerlen (Netherlands); Schins, Roel P.F. [Institut fuer umweltmedizinische Forschung (IUF) at the Heinrich-Heine-University, Auf' m Hennekamp 50, D-40225 Duesseldorf (Germany)]. E-mail: roel.schins@uni-duesseldorf.de

    2007-04-01

    Respirable quartz dust has been classified as a human carcinogen by the International Agency for Research on Cancer. The aim of our study was to investigate the mechanisms of DNA damage by DQ12 quartz in RLE-6TN rat lung epithelial type II cells (RLE). Transmission electron microscopy and flow-cytometry analysis showed a rapid particle uptake (30 min to 4 h) of quartz by the RLE cells, but particles were not found within the cell nuclei. This suggests that DNA strand breakage and induction of 8-hydroxydeoxyguanosine - as also observed in these cells during these treatment intervals - did not result from direct physical interactions between particles and DNA, or from short-lived particle surface-derived reactive oxygen species. DNA damage by quartz was significantly reduced in the presence of the mitochondrial inhibitors rotenone and antimycin-A. In the absence of quartz, these inhibitors did not affect DNA damage, but they reduced cellular oxygen consumption. No signs of apoptosis were observed by quartz. Flow-cytometry analysis indicated that the reduced DNA damage by rotenone was not due to a possible mitochondria-mediated reduction of particle uptake by the RLE cells. Further proof of concept for the role of mitochondria was shown by the failure of quartz to elicit DNA damage in mitochondria-depleted 143B (rho-0) osteosarcoma cells, at concentrations where it elicited DNA damage in the parental 143B cell line. In conclusion, our data show that respirable quartz particles can elicit oxidative DNA damage in vitro without entering the nuclei of type II cells, which are considered to be important target cells in quartz carcinogenesis. Furthermore, our observations indicate that such indirect DNA damage involves the mitochondrial electron transport chain function, by an as-yet-to-be elucidated mechanism.

  3. Iatrogenic Tumor Implantation

    Institute of Scientific and Technical Information of China (English)

    Ying Ma; Ping Bai

    2008-01-01

    Iatrogenic tumor implantation is a condition that results from various medical procedures used during diagnosis or treatment of a malignancy. It involves desquamation and dissemination of tumor cells that develop into a local recurrence or distant metastasis from the tumor under treatment. The main clinical feature of the condition is nodules at the operation's porous channel or incision, which is easily diagnosed in accordance with the case history. Final diagnosis can be made based on pathological examination. Tumor implantation may occur in various puncturing porous channels, including a laparoscopic port, abdominal wall incision, and perineal incision, etc. Besides a malignant tumor,implantation potential exists with diseases, such as a borderline tumor and endometriosis etc. Once a tumor implantation is diagnosed, or suspected, surgical resection is usually conducted.During the diagnosis and treatment of diseases, avoiding and reducing iatrogenic implantation and dissemination has been regarded as an important principle for surgical treatment of tumors. In a clinical practice setting, if possible, excisional biopsy should be employed, if a biopsy is needed. Repeated puncturing should be avoided during a paracentesis. In a laparoscopic procedure, the tissue is first put into a sample bag and then is taken out from the point of incision. After a laparoscopic procedure, the peritoneum, abdominal muscular fasciae, and skin should be carefully closed, and/or the punctured porous channel be excised. In addition, the sample/tissue should be rinsed with distilled water before surgical closure of the abdominal cavity,allowing the exfoliated tumor cells to swell and rupture in the hypo-osmolar solution. Then surgical closure can be conducted following a change of gloves and equipment. The extent of hysteromyomectomy should as far as possible be away from the uterine cavity. The purpose of this study is to make clinicians aware of the possibility of tumor implantation

  4. Implant interactions with orthodontics.

    Science.gov (United States)

    Celenza, Frank

    2012-09-01

    Many situations arise in which orthodontic therapy in conjunction with implant modalities is beneficial, relevant or necessary. These situations might entail orthodontic treatment preparatory to the placement of an implant, such as in the site preparation for implant placement. Traditionally, this has been somewhat well understood, but there are certain guidelines that must be adhered to as well as diagnostic steps that must be followed. Provision of adequate space for implant placement is of paramount importance, but there is also the consideration of tissue manipulation and remodeling which orthodontic therapy can achieve very predictably and orthodontists should be well versed in harnessing and employing this modality of site preparation. In this way, hopeless teeth that are slated for extraction can still be utilized by orthodontic extraction to augment tissues, both hard and soft, thereby facilitating site development. On the corollary, and representing a significant shift in treatment sequencing, there are many situations in which orthodontic mechanotherapy can be simplified, expedited, and facilitated by the placement of an implant and utilization as an integral part of the mechanotherapy. Implants have proven to provide excellent anchorage, and have resulted in a new class of anchorage known as "absolute anchorage". Implants can be harnessed as anchors both in a direct and indirect sense, depending upon the dictates of the case. Further, this has led to the development of orthodontic miniscrew systems and techniques, which can have added features such as flexibility in location and placement, as well as ease of use and removal. As orthodontic appliances evolve, the advent of aligner therapy has become mainstream and well accepted, and many of the aforementioned combined treatment modalities can and should be incorporated into this relatively new treatment modality as well.

  5. Improved Self Fused Check pointing Replication for Handling Multiple Faults in Cloud Computing

    Directory of Open Access Journals (Sweden)

    Sanjay Bansal

    2012-06-01

    Full Text Available The performance of checkpointing replication fault tolerance technique is severely bottlenecks due to handling of number of replicas generated for a large number of nodes to tolerate multiple faults such as multiple failure of nodes, processes etc. In fusion based approach, these checkpointing replicas stored at large number of computing nodes is aggregated into some data structure to handle efficiently through fused data structure. These impose higher overheads of fusing a large numbers of checkpointing replicas. In this paper, a self fused checkpointing replication (SFCR for cloud computing is proposed. All checkpointing replicas assigned to store at a particular node are stored in a self-fused-shared-checkpointing-replicas file already created and located at every node rather than storing as a separate checkpointing element and than fusing. Thus, iteliminates the need of further fusing of the checkpointing replicas stored at different checkpointing replicas storage nodes, as checkpointing replicas assign to store a particular node stored in an already created fuse file at every checkpointing replicas storage node. It improves the performance without affecting the specified fault tolerant capabilities as failure of any node will result in loss of all replicas irrespective of separate checkpointing file or shared checkpointing fused file. Costs to maintain these set of self fused shared files are obviously less than the number of separate replicated files in terms of time and efforts that it takes to create, and update a file. Thus, proposed approach is enhancement of performance without compromising the specified fault tolerancecapability. At the same time when system seems to be prone to many number of faults, some specific self fused shared files consist of important and critical data that can be further replicated to enhance the fault tolerant capability of a group of important and critical nodes or processes at run time. Thus, it also

  6. Electric field cancellation on quartz: a Rb adsorbate induced negative electron affinity surface

    CERN Document Server

    Sedlacek, J A; Rittenhouse, S T; Weck, P F; Sadeghpour, H R; Shaffer, J P

    2015-01-01

    We investigate the (0001) surface of single crystal quartz with a submonolayer of Rb adsorbates. Using Rydberg atom electromagnetically induced transparency, we investigate the electric fields resulting from Rb adsorbed on the quartz surface, and measure the activation energy of the Rb adsorbates. We show that the adsorbed Rb induces a negative electron affinity (NEA) on the quartz surface. The NEA surface allows low energy electrons to bind to the surface and cancel the electric field from the Rb adsorbates. Our results are important for integrating Rydberg atoms into hybrid quantum systems and the fundamental study of atom-surface interactions, as well as applications for electrons bound to a 2D surface.

  7. Rotational Symmetry and Absolute Sign of Second-Order Susceptibility of α-Quartz

    Institute of Scientific and Technical Information of China (English)

    吕荣; 王鸿飞

    2003-01-01

    We investigate the rotational symmetry and absolute sign of the effective second-order susceptibility of the righthanded z-cut α-quartz crystal in different crystal orientations through the second-harmonic-generation phase interference between standard and reference of thin α-quartz plates. The Ds rotational symmetry of the z-cut α-quartz crystal shows 6 alternating sign sections of the second-order susceptibility in the 360° rotation, which leads to two distinctive interference patterns between the reference and standard second harmonic field. From this information, the sign of the interference pattern in the second harmonic phase measurement could be readily derived.

  8. Using optically stimulated electrons from quartz for the estimation of natural doses

    DEFF Research Database (Denmark)

    Ankjærgaard, Christina; Murray, A.S.; Denby, Phil M.;

    2009-01-01

    quartz samples are studied to examine the possible use of OSE as a chronometer. First the relative variability in OSE and OSL growth curve shapes and the effect of preheat on these are presented, and from these curves, conclusions are drawn concerning the charge movement in natural quartz. Secondly...... dose using the single-aliquot regenerative-dose (SAR) procedure. Finally, a comparative study of the equivalent doses estimated using both OSE and OSL from 10 quartz samples are presented, and it is shown that OSE has a significant potential in retrospective dosimetry....

  9. Dual origins of Xiaoqinling gold-bearing quartz veins: Fluid inclusion evidence

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Fluid inclusion research in Archean metamorphic rocks, Yanshanian granite and gold-bearing quartz veins shows that regional metamorphic fluids are high temperature and high saline, Yanshanian post-granitic fluids are CO2-bearing low saline, and ore-forming fluids are also CO2-rich low saline. In gold-barren/free parts of quartz veins in gold deposits, daughter mineral-bearing high saline inclusions related with metamorphic fluids remained. This proclaims quartz veins hosting gold ores might have been formed in early metamorphism, and overlapped or mineralized by late Yanshanian gold-bearing fluids.

  10. Chirality of quartz. Fibrosis and tumour development in dust inoculated mice.

    Science.gov (United States)

    Ebbesen, P

    1991-10-01

    Dextro (d) and laevo (l) forms of quartz dust was inoculated intranasally and subcutaneously into 2-month-old (C57 x BALB/c)F1 mice which were killed 18 months later. Both d and l quartz caused fibrosis, liver nodule formation and an enhanced incidence of lymphoma/leukemia. However, the tumour incidence was significantly higher in l than in d quartz dust-treated animals. It is concluded that in addition to effects clearly independent of chirality there is evidence that the biological response to nonidentical mirror images of solid crystals may differ.

  11. Limits to depletion of blue-green light stimulated luminescence in feldspars: Implications for quartz dating

    DEFF Research Database (Denmark)

    Jain, M.; Singhvi, A.K.

    2001-01-01

    -red stimulation at elevated temperature (220 degreesC) (ETIR) permits depletions of charges in Type (A) and Type (B) to the extent that the feldspar BGSL can be reduced by up to 97% in 5 min. These results offer prospects for (1) improved precision in paleodose estimates based on quartz; (2) BGSL dating of quartz...... in a polyminerallic fine grain samples; (3) age estimates based on both quartz and feldspars from the same aliquots, and (4) dating based on feldspar micro-inclusions. (C) 2001 Elsevier Science Ltd. All rights reserved....

  12. Positron implantation in solids

    Energy Technology Data Exchange (ETDEWEB)

    Ghosh, V.J.; Lynn, K.G.; Welch, D.O.

    1993-12-31

    The Monte Carlo technique for modeling positron prior to annihilation and electron implantation in semi-infinite metals is described. Particle implantation is modelled as a multistep process, a series of collisions with the atoms of the host material. In elastic collisions with neutral atoms there is no transfer of energy. The particle loses energy by several different channels, excitation of the electron gas, ionization of the ion cores, or, at low energies, by phonon excitation. These competing scattering mechanisms have been incorporated into the Monte Carlo framework and several different models are being used. Brief descriptions of these Monte Carlo schemes, as well as an analytic model for positron implantation are included. Results of the Monte Carlo simulations are presented and compared with expermental data. Problems associated with modeling positron implantation are discuss and the need for more expermental data on energy-loss in different materials is stressed. Positron implantation in multilayers of different metals is briefly described and extensions of this work to include a study of multilayers and heterostructures is suggested.

  13. Interdiffusion of Polycarbonate in Fused Deposition Modeling Welds

    Science.gov (United States)

    Seppala, Jonathan; Forster, Aaron; Satija, Sushil; Jones, Ronald; Migler, Kalman

    2015-03-01

    Fused deposition modeling (FDM), a now common and inexpensive additive manufacturing method, produces 3D objects by extruding molten polymer layer-by-layer. Compared to traditional polymer processing methods (injection, vacuum, and blow molding), FDM parts have inferior mechanical properties, surface finish, and dimensional stability. From a polymer processing point of view the polymer-polymer weld between each layer limits the mechanical strength of the final part. Unlike traditional processing methods, where the polymer is uniformly melted and entangled, FDM welds are typically weaker due to the short time available for polymer interdiffusion and entanglement. To emulate the FDM process thin film bilayers of polycarbonate/d-polycarbonate were annealed using scaled times and temperatures accessible in FDM. Shift factors from Time-Temperature Superposition, measured by small amplitude oscillatory shear, were used to calculate reasonable annealing times (min) at temperatures below the actual extrusion temperature. The extent of interdiffusion was then measured using neutron reflectivity. Analogous specimens were prepared to characterize the mechanical properties. FDM build parameters were then related to interdiffusion between welded layers and mechanical properties. Understating the relationship between build parameters, interdiffusion, and mechanical strength will allow FDM users to print stronger parts in an intelligent manner rather than using trial-and-error and build parameter lock-in.

  14. Mechanical analysis of lightweight constructions manufactured with fused deposition modeling

    Science.gov (United States)

    Bagsik, A.; Josupeit, S.; Schoeppner, V.; Klemp, E.

    2014-05-01

    Additive production techniques have the advantage of manufacturing parts without needing a forming tool. One of the most used additive manufacturing processes is "Fused Deposition Modeling" (FDM) which allows the production of prototypes and end-use parts. Due to the manufacture layer by layer, also complex part geometries can be created in one working step. Furthermore, lightweight parts with specific inner core structures can be manufactured in order to achieve good weightrelated strength properties. In this paper the mechanical behavior of lightweight parts manufactured with the 3D production system Fortus 400mc from Stratasys and the material Polyetherimide (PEI) with the trade name Ultem*9085 is analyzed. The test specimens were built up with different inner structures and building directions. Therefore, test specimens with known lightweight core geometries (e.g. corrugated and honeycomb cores) were designed. A four-point bending test was conducted to analyze the strength properties as well as the weight-related strength properties. Additionally the influence of the structure width, the structure wall thickness and the top layer thickness was analyzed using a honeycomb structure.

  15. Plasticized protein for 3D printing by fused deposition modeling

    Science.gov (United States)

    Chaunier, Laurent; Leroy, Eric; Della Valle, Guy; Lourdin, Denis

    2016-10-01

    The developments of Additive Manufacturing (AM) by Fused Deposition Modeling (FDM) now target new 3D printable materials, leading to novel properties like those given by biopolymers such as proteins: degradability, biocompatibility and edibility. Plasticized materials from zein, a storage protein issued from corn, present interesting thermomechanical and rheological properties, possibly matching with AM-FDM specifications. Thus commercial zein plasticized with 20% glycerol has a glass transition temperature (Tg) at about 42°C, after storage at intermediate relative humidity (RH=59%). Its principal mechanical relaxation at Tα ≈ 50°C leads to a drop of the elastic modulus from about 1.1 GPa, at ambient temperature, to 0.6 MPa at Tα+100°C. These values are in the same range as values obtained in the case of standard polymers for AM-FDM processing, as PLA and ABS, although relaxation mechanisms are likely different in these materials. Such results lead to the setting up of zein-based compositions printable by AM-FDM and allow processing bioresorbable printed parts, with designed 3D geometry and structure.

  16. Measuring and Modelling Crowd Flows - Fusing Stationary and Tracking Data

    CERN Document Server

    Treiber, Martin

    2016-01-01

    The two main data categories of vehicular traffic flow, stationary detector data and floating-car data, are also available for many Marathons and other mass-sports events: Loop detectors and other stationary data sources find their counterpart in the RFID tags of the athletes recording the split times at several stations during the race. Additionally, more and more athletes use smart-phone apps generating track data points that are the equivalent of floating-car data. We present a methodology to detect congestions and estimate the location of jam-fronts, the delay times, and the spatio-temporal speed and density distribution of the athlete's crowd flow by fusing these two data sources based on a first-order macroscopic model with triangular fundamental diagram. The method can be used in real-time or for analyzing past events. Using synthetic "ground truth" data generated by simulations with the Intelligent-Driver Model, we show that, in a real-time application, the proposed algorithm is robust and effective w...

  17. PREPARATION OF HIGH THERMAL EXPANSION COEFFICIENT PORCELAINS FUSED TO METALS

    Institute of Scientific and Technical Information of China (English)

    J.P. Yang; J.Q. Wu

    2003-01-01

    Usually the thermal expansion coefficients (TEC) of metals are higher than that of porcelains. In order to match the TECs in the case of coating porcelains on metals, high TEC porcelains are needed. In this research, the high TEC phase leucite(KAlSi2 O6) in the high TEC porcelain was prepared by sol-gel method. The crystal size of leucite made by sol-gel is about 77nm through controlling the process parameters. The process from xerogel to leucite was investigated by means of DSC (differential scanning calorimetry), TG (thermogravimetry), XRD ( X-ray diffraction) and IR(infrared absorption spectrum). Leucite had been detected after the gel was treated at 900°C, this formation temperature is about 250°C lower than that of melting method.The porcelain made from 50% of the leucite powder and 50%o of low fused temperature frit has an average TEC of 19.2× 10-6/° C from room temperature to 450°C, which is much higher than the common porcelains.

  18. Person Tracking System by Fusing Multicues Based on Patches

    Directory of Open Access Journals (Sweden)

    Song Min Jia

    2015-01-01

    Full Text Available A person tracking algorithm by fusing multicues based on patches is proposed to solve the problem of distinguishing person, occlusion, and illumination variations. Kinect is mounted on the robot for providing color images and depth maps. A detector representing a person by using the fusion of multicues based on patches is proposed. The detector divides the person into many patches and then represents each patch by using depth-color histograms and depth-texture histograms. The appearance representation, considering depth, color, and texture information, has powerful discrimination ability to handle the problems of occlusion, illumination changes, and pose variations. Considering the motion of the robot and person, a tracker called motion extended Kalman filter (MEKF is presented to predict the person’s position. The result of the tracker is treated as a candidate sample of the detector, and then the result of the detector is the previous knowledge of the tracker. The detector and tracker supplement each other and improve the tracking performance. To drive the robot towards the given person precisely, a fuzzy based intelligent gear control strategy (FZ-IGS is implemented. Experiments demonstrate that the proposed approach can track a person in a complex environment and have an optimum performance.

  19. Indirect slumping of D263 glass on Fused Silica mould

    Science.gov (United States)

    Proserpio, Laura; Wen, Mingwu; Breunig, Elias; Burwitz, Vadim; Friedrich, Peter; Madarasz, Emanuel

    2016-07-01

    The Slumped Glass Optic (SGO) group of the Max Planck Institute for Extraterrestrial physics (MPE) is studying the indirect slumping technology for its application to X-ray telescope manufacturing. Several aspects of the technology have been analyzed in the past. During the last months, we concentrated our activities on the slumping of Schott D263 glass on a precise machined Fused Silica mould: The concave mould was produced by the Italian company Media Lario Technologies with the parabola and hyperbola side of the typical Wolter I design in one single piece. Its shape quality was estimated by optical metrology to be around 6 arcsec Half Energy Width (HEW) in double reflection. The application of an anti-sticking Boron Nitride layer was necessary to avoid the adhesion of the glass on the mould during the forming process at high temperatures. The mould has been used for the slumping of seven mirror segments 200 mm long, 100 mm wide, and with thickness of 200 μm or 400 μm. The influence of the holding time at maximum temperature was explored in this first run of tests. The current results of the activities are described in the paper and plans for further investigations are outlined.

  20. Standardizing Quality Assessment of Fused Remotely Sensed Images

    Science.gov (United States)

    Pohl, C.; Moellmann, J.; Fries, K.

    2017-09-01

    The multitude of available operational remote sensing satellites led to the development of many image fusion techniques to provide high spatial, spectral and temporal resolution images. The comparison of different techniques is necessary to obtain an optimized image for the different applications of remote sensing. There are two approaches in assessing image quality: 1. Quantitatively by visual interpretation and 2. Quantitatively using image quality indices. However an objective comparison is difficult due to the fact that a visual assessment is always subject and a quantitative assessment is done by different criteria. Depending on the criteria and indices the result varies. Therefore it is necessary to standardize both processes (qualitative and quantitative assessment) in order to allow an objective image fusion quality evaluation. Various studies have been conducted at the University of Osnabrueck (UOS) to establish a standardized process to objectively compare fused image quality. First established image fusion quality assessment protocols, i.e. Quality with No Reference (QNR) and Khan's protocol, were compared on varies fusion experiments. Second the process of visual quality assessment was structured and standardized with the aim to provide an evaluation protocol. This manuscript reports on the results of the comparison and provides recommendations for future research.

  1. Covalent non-fused tetrathiafulvalene-acceptor systems.

    Science.gov (United States)

    Pop, Flavia; Avarvari, Narcis

    2016-06-28

    Covalent donor-acceptor (D-A) systems have significantly contributed to the development of many organic materials and to molecular electronics. Tetrathiafulvalene (TTF) represents one of the most widely studied donor precursors and has been incorporated into the structure of many D-A derivatives with the objective of obtaining redox control and modulation of the intramolecular charge transfer (ICT), in order to address switchable emissive systems and to take advantage of its propensity to form regular stacks in the solid state. In this review, we focus on the main families of non-fused TTF-acceptors, which are classified according to the nature of the acceptor: nitrogen-containing heterocycles, BODIPY, perylenes and electron poor unsaturated hydrocarbons, as well as radical acceptors. We describe herein the most representative members of each family with a brief mention of their synthesis and a special focus on their D-A characteristics. Special attention is given to ICT and its modulation, fluorescence quenching and switching, photoconductivity, bistability and spin distribution by discussing and comparing spectroscopic and electrochemical features, photophysical properties, solid-state properties and theoretical calculations.

  2. Explosively formed fuse opening switches for multi-joule applications

    Energy Technology Data Exchange (ETDEWEB)

    Goforth, J.H.; Anderson, B.G.; Bartram, D.E. [and others

    1995-08-01

    High explosive pulsed power (HEPP) systems are capable of generating very high energies in magnetic fields. Such stored energy is usually developed on time scales of a few tens or hundreds of microseconds. Many applications require shorter pulses and opening switches provide one way to use the large energy available for faster applications. With current flowing in an inductive circuit, introducing resistance produces voltage that can be used to drive current into a load. For an opening switch with a fast rising resistance, the load current rise time is determined by the R/L time constant of the circuit. A significant fraction of the circuit energy must be dissipated in the process, and in applications where very large energies must be dealt with only a few types of switches can be used. Experiments with high explosive driven opening switches have produced a few switches that can carry tens of MA current, and open on the time scale of one or a few {mu}s. {sup 1} We have specialized in a type of switch that we call an explosively formed fuse (EFF) switch at levels of {approximately}3 TW for 2{mu}s has become routine, and we will describe its characteristics and give data from a number of tests.

  3. Congenitally caused fused labia in the common marmoset (Callithrix jacchus).

    Science.gov (United States)

    Isachenko, E F; Nayudu, P L; Isachenko, V V; Nawroth, F; Michelmann, H W

    2002-12-01

    In this paper, the occurrence of an external genital abnormality in female marmoset monkeys (fused labia) is discussed. This malformation was detected, for the first time, in a group of animals at the German Primate Center (GPC), Goettingen. The malformed vulva was completely sealed except for an opening of 1.5-2.5 mm around the urethra sufficient for urination. Because of this defect the animals were not able to copulate. As a consequence, the affected females were functionally infertile although they had a normal genital tract and a regular cycle. This vulvar abnormality was found in 12 females, offspring of 10 pairs in which either one or both came to the German Primate Center from two genetically related colonies in Munich, Germany, and one colony in Basel, Switzerland. The abnormality appeared to be recessive and inheritable from either parent. In pairs in which both animals were from one of the mentioned colonies, 45% of the female offspring were affected. In pairs where only one partner came from these colonies, 26% of female offspring had the malformation. These results indicate that avoidance of inbreeding, which is frequently performed in primate colonies, may reduce, but not eliminate the expression of abnormalities of genetic origin. Therefore selective breeding is required, and, in colonies where these recessive mutations are widespread, the development of genetic screening tests would be advantageous.

  4. FUSE observations of the Blue Compact Dwarf Galaxy Mrk 59

    CERN Document Server

    Thuan, T X; Izotov, Yu I

    2001-01-01

    New FUSE far-UV spectroscopy of the nearby metal-deficient (Zsun/8) cometary Blue Compact Dwarf (BCD) galaxy Markarian (Mrk) 59 is discussed. The data are used to investigate element abundances in its interstellar medium. The H I absorption lines are characterized by narrow cores which are interstellar in origin and by broad wings which are stellar in origin. The mean interstellar H I column density is ~ 7x10E20 cm-2 in Mrk 59. No H2 lines are seen and N(H2) is < 10E15 cm-2 at the 10 sigma level. The lack of diffuse H2 is due to the combined effect of a strong UV radiation field which destroys the H2 molecules and a low metallicity which leads to a scarcity of dust grains necessary for H2 formation. P-Cygni profiles of the S VI 933.4, 944.5 A and O VI 1031.9, 1037.6 A lines are seen, indicating the presence of very hot O stars and a stellar wind terminal velocity of ~ 1000 km/s. By fitting the line profiles with multiple components having each a velocity dispersion b = 7 km/s and spanning a radial velocity...

  5. Management of peri-implantitis

    Directory of Open Access Journals (Sweden)

    Jayachandran Prathapachandran

    2012-01-01

    Full Text Available Peri-implantitis is a site-specific infectious disease that causes an inflammatory process in soft tissues, and bone loss around an osseointegrated implant in function. The etiology of the implant infection is conditioned by the status of the tissue surrounding the implant, implant design, degree of roughness, external morphology, and excessive mechanical load. The microorganisms most commonly associated with implant failure are spirochetes and mobile forms of Gram-negative anaerobes, unless the origin is the result of simple mechanical overload. Diagnosis is based on changes of color in the gingiva, bleeding and probing depth of peri-implant pockets, suppuration, X-ray, and gradual loss of bone height around the tooth. Treatment will differ depending upon whether it is a case of peri-implant mucositis or peri-implantitis. The management of implant infection should be focused on the control of infection, the detoxification of the implant surface, and regeneration of the alveolar bone. This review article deals with the various treatment options in the management of peri-implantitis. The article also gives a brief description of the etiopathogenesis, clinical features, and diagnosis of peri-implantitis.

  6. Fluoride retardation from quartz sand-packed column tests

    Directory of Open Access Journals (Sweden)

    Eduardo Usunoff

    2009-06-01

    Full Text Available Inasmuch as both low and high concentrations of F- in groundwater have different detrimental effects on human health (increased dental caries, and mottled enamel or even severe structural bone deformations, respectively, many efforts have focused on the movement of such anion in aqueous systems. It is so because water drinking is the main intake of F- by humans. This paper presents the results of seven dynamic experiments in which solutions of varying [F-], pH, and flow velocities circulated through columns packed with clean quartz sand. The breakthrough data were analyzed by means of a computer code adapted to the estimation of equilibrium and non-equilibrium solute transport parameters from miscible displacement experiments in a steady-state, uniform flow field using a pulse-type or continuous source. It was found that larger retardation factors (R are associated with low pH, low [F-] in the feed solutions, and larger flow velocities. Such results appear to be related to the form of the F species, the rather weak bond between the adsorbate and the quartz sand, and stronger anion repulsion at low pore velocities. The estimated values for R vary between 1,22 and 1,50, whereas the distribution coefficients were in the range of 0,1 to 0,05 L kg-1. It should be said that the breakthrough curves display hysteresis, leading to a desorption behavior that proceeds faster than the adsorption process.Puesto que tanto valores bajos como altos de F- en las aguas subterráneas tienen efectos adversos en la salud de los humanos (mayor cantidad de caries, y manchas del esmalte dental e incluso deformaciones óseas, respectivamente, han sido muchos los esfuerzos destinados a dilucidar el movimiento de especies fluoradas en ambientes acuosos. Ello es así porque el consumo de agua por parte de seres humanos representa la mayor fuente de ingreso de F-. Este trabajo presenta los resultados de siete experimentos dinámicos en los que soluciones de diferentes [F

  7. Neptunium(V) sorption behavior on clinoptilolite, quartz and montmorillonite

    Energy Technology Data Exchange (ETDEWEB)

    Bertetti, F.P.; Pabalan, R.T.; Turner, D.R.; Almendarez, M.G. [Southwest Research Inst., San Antonio, TX (United States). Center for Nuclear Waste Regulatory Analyses

    1996-08-01

    Performance assessment models have identified {sup 237}Np as a radionuclide of concern in meeting release limits established for the geologic disposal of high-level nuclear waste at the proposed repository at Yucca Mountain, Nevada. In this study, quartz, clinoptilolite, and montmorillonite, which are minerals representative of phases that occur both in the rock matrix and as fracture coatings at Yucca Mountain, were reacted with {sup 237}Np-bearing solutions to characterize the sorption behavior of Np(V) on these minerals. Batch experiments were conducted over a wide range of conditions in which pH of solution, surface loading, sorbent surface area, initial concentration of Np(V), and partial pressure of CO{sub 2} were varied. Initial Np(V) concentrations were between 1 {times} 10{sup {minus}7} and 1 {times} 10{sup {minus}6} M in electrolyte solutions of 0.1 or 0.01 M NaNO{sub 3}. The oxidation state of Np in solution was verified with NIR spectroscopy and by solvent extraction. Prior to the start of experiments, minerals were pretreated to eliminate impurities, and the clinoptilolite and montmorillonite were converted to Na-form by ion exchange with NaCl solutions. Results indicate that, for all three minerals, Np(V) sorption begins at pH values coincident with the start of hydrolysis in solution ({approximately}7). For solutions undersaturated with respect to atmospheric CO{sub 2}, sorption increases continuously with increasing pH. Under equilibrium with atmospheric CO{sub 2}, Np(V) sorption is important in the pH range (7--9.5) where NpO{sub 2}(OH){sup 0}(aq) is significant, whereas sorption is inhibited at higher pH where neptunyl carbonate complexes are the predominant species.

  8. Dental implants: A review.

    Science.gov (United States)

    Guillaume, B

    2016-12-01

    A high number of patients have one or more missing tooth and it is estimated that one in four American subjects over the age of 74 have lost all their natural teeth. Many options exist to replace missing teeth but dental implants have become one of the most used biomaterial to replace one (or more) missing tooth over the last decades. Contemporary dental implants made with titanium have been proven safe and effective in large series of patients. This review considers the main historical facts concerned with dental implants and present the different critical factors that will ensure a good osseo-integration that will ensure a stable prosthesis anchorage. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  9. Complications in implant dentistry

    Science.gov (United States)

    Hanif, Ayesha; Qureshi, Saima; Sheikh, Zeeshan; Rashid, Haroon

    2017-01-01

    After tooth loss, an individual may seek tooth replacement so that his/her function and esthetics could be restored. Clinical prosthodontics, during the past decade, has significantly improved and developed according to the advancements in the science and patient's demands and needs. Conventional options in prosthodontics for substituting a missing single tooth include the removable partial denture, partial and full coverage bridgework, and resin-bonded bridgework. Dental implants have gained increasing popularity over the years as they are capable of restoring the function to near normal in both partial and completely edentulous arches. With substantial evidence available, fixed implant-supported prosthesis are fully acknowledged as a reliable treatment option for the replacement of single or multiple missing teeth nowadays. While dental implants are increasingly becoming the choice of replacement for missing teeth, the impediments associated with them are progressively emerging too. PMID:28435381

  10. Dental Implant Complications.

    Science.gov (United States)

    Liaw, Kevin; Delfini, Ronald H; Abrahams, James J

    2015-10-01

    Dental implants have increased in the last few decades thus increasing the number of complications. Since many of these complications are easily diagnosed on postsurgical images, it is important for radiologists to be familiar with them and to be able to recognize and diagnose them. Radiologists should also have a basic understanding of their treatment. In a pictorial fashion, this article will present the basic complications of dental implants which we have divided into three general categories: biomechanical overload, infection or inflammation, and other causes. Examples of implant fracture, loosening, infection, inflammation from subgingival cement, failure of bone and soft tissue preservation, injury to surround structures, and other complications will be discussed as well as their common imaging appearances and treatment. Lastly, we will review pertinent dental anatomy and important structures that are vital for radiologists to evaluate in postoperative oral cavity imaging.

  11. α-β Transition in Quartz: Temperature and Pressure Dependence of the Thermodynamic Quantities for β-Quartz and β-Cristobalite as Piezoelectric Materials

    Science.gov (United States)

    Lider, M. C.; Yurtseven, H.

    2014-12-01

    Temperature and pressure dependencies of the thermal expansivity (αp), isothermal compressibility (κT) and the specific heat (Cp - Cv) are studied for piezoelectric materials, in particular, for β-quartz. By analyzing the temperature (at 1 atm) and pressure (at 848 K) dependence of the observed volume V from the literature, the thermodynamic functions (αp, κT and Cp - Cv) are obtained and the Pippard relations (Cp - Cv vs. Vαp and αp vs. κT) close to the transition from the β-quartz to the β-cristobalite are examined.

  12. Sorption of fluoride by quartz sand: batch tests

    Directory of Open Access Journals (Sweden)

    Eduardo Usunoff

    2009-06-01

    Full Text Available Despite the many efforts of scientists, in particular those from the field of soil science, the fate and distribution of fluorine (F species in soils and aquifers remain relatively unraveled. As for groundwater systems, such a shortcoming makes difficult the finding and development of safe water supplies. Likewise, the use of transport models does not render acceptable results because of the many uncertainties related to the behavior of F in aqueous media. This paper presents the results of four batch test in which solutions of different pH and [F-] (concentration of fluoride were in contact during 48 hours with clean quartz sand grains. The resulting data were fitted by linear versions of the Freundlich, the Langmuir, and the Langmuir-Freundlich models. The [F-] was varied between 0,5 and 10 mg L-1, except in one batch where a large initial concentration of F was used (45 mg L-1, and the range of pH used was 2,95 to 5,02. From a sieve analysis, the quartz grains had a medium size (d50 of 0,25 mm, and a uniformity coefficient (d40/d90 of 1,65. According to the fits and some dedicated goodness of fit indices, the Langmuir-Freundlich approach gave the best results for the batch test at the lowest pH, whereas the three remaining tests data were fitted by the Freundlich equation. It has to be mentioned that the pH of the equilibrium solutions were higher than the pH of the initial solutions, which was interpreted as an exchange process of OH- by F- on the quartz sand surface. However, such an exchange does not stand out as the exclusive mechanism promoting the F- disappearance from solution. It is deemed that the obtained results can be used as initial estimates of parameters in models used for calibrating the transport of F- in aquifers.A pesar de los muchos esfuerzos de los científicos, en particular de aquellos dedicados a las ciencias del suelo, el destino y la distribución de las especies de F (flúor en suelos y acuíferos continúan siendo

  13. Vibration characteristic analysis method for the quartz microgyroscope based on the admittance circle

    Science.gov (United States)

    Wang, Haoxu; Dong, Peitao; Xie, Liqiang; Wu, Xuezhong

    2014-03-01

    The vibration characteristic analysis method for a quartz microgyroscope based on the admittance circle is reported in this paper. Admittance theory is introduced and the admittance circle principle is analysed to study the vibration characteristics of the quartz microgyroscope. The prototype gyroscope was fabricated by micro-electromechanical systems (MEMS) technology. The admittance and phase diagram of the work mode were obtained by vibration mode test systems. Then the admittance circle of the work mode was drawn, and the parameter identification of the transfer function between the voltage and current was completed to analyse the vibration characteristics. Therefore, the vibration characteristic analysis method based on the admittance circle can be used to build the transfer function of the quartz microgyroscope, which is helpful for the design of a high performance quartz microgyroscope.

  14. Vibration characteristic analysis method for the quartz microgyroscope based on the admittance circle

    Directory of Open Access Journals (Sweden)

    Haoxu Wang

    2014-02-01

    Full Text Available The vibration characteristic analysis method for a quartz microgyroscope based on the admittance circle is reported in this paper. Admittance theory is introduced and the admittance circle principle is analysed to study the vibration characteristics of the quartz microgyroscope. The prototype gyroscope was fabricated by micro-electromechanical systems (MEMS technology. The admittance and phase diagram of the work mode were obtained by vibration mode test systems. Then the admittance circle of the work mode was drawn, and the parameter identification of the transfer function between the voltage and current was completed to analyse the vibration characteristics. Therefore, the vibration characteristic analysis method based on the admittance circle can be used to build the transfer function of the quartz microgyroscope, which is helpful for the design of a high performance quartz microgyroscope.

  15. Influence of H2O Rich Fluid Inclusions on Quartz Deformation

    Science.gov (United States)

    Thust, Anja; Heilbronner, Renée.; Stünitz, Holger; Tarantola, Alexandre; Behrens, Harald

    2010-05-01

    The effect of H2O on the strength of quartz is well known and has been discussed many times in the literature (e.g. Griggs & Blacic 1965, Kronenberg 1994). In this project we study the H2O interactions between natural dry quartz and H2O rich fluid inclusions during deformation in the solid medium Griggs apparatus. High pressure and temperature experiments were carried out using a quartz single crystal containing a large number of H2O-rich fluid inclusions. Adjacent to the fluid inclusions the crystal is essentially dry (Kronenberg A.K., (1994): Hydrogen specifications and chemical weakening of quartz, Rev. Mineral. Ser. 29 (1994), pp. 123-176.

  16. Greatly improved small inductance measurement using quartz crystal parasitic capacitance compensation.

    Science.gov (United States)

    Matko, Vojko; Jezernik, Karel

    2010-01-01

    Generally, quartz crystal inductance frequency pulling in oscillators is very low and therefore is not often used in practice. The new method of improving frequency pullability uses inductance to compensate for quartz stray capacitances. To this end, a special AT fundamental quartz crystal working near the antiresonance frequency is selected. By modifying its equivalent circuit with load inductance and series tuning capacitance, the magnetic sensing of the circuit can be highly improved. The experimental results show that the new approach using the quartz crystal stray capacitance compensation method increases the frequency pulling range (from ≅2 kHz/μH to ≅600 kHz/μH) by ×300 depending on the type of oscillator, making possible the measurement of nano-magnetic changes.

  17. Anomalous quartz from the Roter Kamm impact crater, Namibia - Evidence for post-impact hydrothermal activity?

    Science.gov (United States)

    Koeberl, Christian; Fredriksson, Kurt; Goetzinger, Michael; Reimold, Wolf Uwe

    1989-01-01

    Quartz pebbles from the Roter Kamm impact crater (the Namib Desert, SWA/Namibia) were examined for evidence of impact-induced hydrothermal activity, using results from microprobe analyses, neutron activation analyses, transmission IR spectroscopy, and X-ray diffractometry. It was found that the pebbles consisted of pure quartz, which contains three different types of fluid inclusions. These were identified as primary inclusions (5-10 microns) that record the formation conditions of the quartz, very small (less than 1 micron) secondary inclusions associated with the grain boundaries, and late inclusions of irregular size. It is concluded that the quartz and the primary inclusions may provide evidence for a postimpact phase of extensive hydrothermal activity, generated by the residual heat from the kinetic energy of the impact.

  18. Influences of neutral oxygen vacancies and ′1 centers on -quartz

    Institute of Scientific and Technical Information of China (English)

    李会然; 程新路; 张红; 赵峰

    2015-01-01

    Our calculations demonstrate that the concentration of neutral oxygen vacancies can affect the geometrical structrue, electronic structure, and optical properties ofα-quartz. Moreover, the distribution of the neutral oxygen divacancy can also exert some infl uence on the properties ofα-quartz. The dissimilarity and similarities are presented in the corresponding density of state (DOS) and absorption spectrum. In addition, when a higher defect concentration is involved inα-quartz, the infl uence of E 01 center on the geometry ofα-quartz becomes more significant. However, the introduction of an E 01 center barely results in any improvement compared with the infl uence produced by the corresponding neutral defect.

  19. The Quartz-Crystal Microbalance in an Undergraduate Laboratory Experiment: I. Fundamentals and Instrumentation

    Science.gov (United States)

    Tsionsky, Vladimir

    2007-01-01

    The fundamentals, as well as the instrumentation of the quartz-crystal microbalance (QCM) technique that is used in an undergraduate laboratory experiment are being described. The QCM response can be easily used to change the properties of any system.

  20. Optimising the separation of quartz and feldspar optically stimulated luminescence using pulsed excitation

    DEFF Research Database (Denmark)

    Ankjærgaard, Christina; Jain, Mayank; Thomsen, Kristina Jørkov;

    2010-01-01

    In luminescence dating, the two most commonly used natural minerals, quartz and feldspar, are exposed to different dose rates in the natural environment, and so record different doses. The luminescence signals also have different stabilities. For accurate dosimetry, the signals from these two...... minerals must be separated, either by physical separation of the mineral grains, or by instrumental separation of the luminescence signals. The luminescence signals from quartz and feldspar have different luminescence lifetimes under pulsed optical stimulation. This difference in lifetime can be used...... to discriminate between the two signals from a mixed quartz-feldspar sample. The purpose of this study is to identify optimum measurement conditions for the best separation of quartz OSL from that of feldspar in a mixed sample using pulsed stimulation and time-resolved OSL. We integrate the signal from 5 μs after...

  1. Magneto-optic sensor based on electrogyration compensation and single-quartz crystal

    Science.gov (United States)

    Li, Changsheng; Cui, He; Zhang, Xuan

    2016-11-01

    Magnetooptic sensor based on electrogyration compensation is proposed and experimentally demonstrated by using single quartz crystal. The sensing unit is composed of single quartz crystal and two polarizers. Quartz crystal exhibits magneto-optic, electro-optic and electrogyration effects, thus magneto-optic Faraday rotation angle can be compensated by the electrogyration angle induced by the compensating voltage applied to the crystal. The compensating voltage is sensitive to both the deviation angle between light beam and principal crystalline axis, and the azimuth angle of polarizer. The 50Hz ac magnetic flux density within 267Gs has been measured, the compensating voltage is 0.72V/Gs for a single quartz crystal with a length of 23mm. The proposed sensor has potential application to closed-loop measurement of magnetic field.

  2. Cathodoluminescence investigations on quartz cement in sandstones of Khabour Formation from Iraqi Kurdistan region, northern Iraq

    DEFF Research Database (Denmark)

    Omer, Muhamed Fakhri; Friis, Henrik

    The Ordovician deltaic to shallow marine Khabour Formation in Northern Iraq consists mainly of sandstone with minor siltstone and interbedded shale. The sandstones are pervasively cemented by quartz that resulted in very little preserved primary porosity. Cathodoluminescence and petrographic stud...

  3. Finding model parameters: Genetic algorithms and the numerical modelling of quartz luminescence

    Energy Technology Data Exchange (ETDEWEB)

    Adamiec, Grzegorz [Department of Radioisotopes, Institute of Physics, Silesian University of Technology, ul. Krzywoustego 2, 44-100 Gliwice (Poland)]. E-mail: grzegorz.adamiec@polsl.pl; Bluszcz, Andrzej [Department of Radioisotopes, Institute of Physics, Silesian University of Technology, ul. Krzywoustego 2, 44-100 Gliwice (Poland); Bailey, Richard [Department of Geography, Royal Holloway, University of London, Egham, Surrey, TW20 0EX (United Kingdom); Garcia-Talavera, Marta [LIBRA, Centro I-D, Campus Miguel Delibes, 47011 Valladolid (Spain)

    2006-08-15

    The paper presents an application of genetic algorithms (GAs) to the problem of finding appropriate parameter values for the numerical simulation of quartz thermoluminescence (TL). We show that with the use of GAs it is possible to achieve a very good match between simulated and experimentally measured characteristics of quartz, for example the thermal activation characteristics of fired quartz. The rate equations of charge transport in the numerical model of luminescence in quartz contain a large number of parameters (trap depths, frequency factors, populations, charge capture probabilities, optical detrapping probabilities, and recombination probabilities). Given that comprehensive models consist of over 10 traps, finding model parameters proves a very difficult task. Manual parameter changes are very time consuming and allow only a limited degree of accuracy. GAs provide a semi-automatic way of finding appropriate parameters.

  4. Inter-comparison in {sup 10}Be analysis starting from pre-purified quartz

    Energy Technology Data Exchange (ETDEWEB)

    Schnabel, C. [Scottish Universities Environmental Research Centre (SUERC), Rankine Avenue, East Kilbride G75 0QF (United Kingdom)]. E-mail: c.schnabel@suerc.gla.ac.uk; Reinhardt, L. [Department of Geographical and Earth Sciences, University of Glasgow G12 8QQ (United Kingdom); Department of Nuclear Physics, Research School of Physical Sciences and Engineering, Australian National University, ACT 0200 (Australia); Barrows, T.T. [Department of Nuclear Physics, Research School of Physical Sciences and Engineering, Australian National University, ACT 0200 (Australia); Bishop, P. [Department of Geographical and Earth Sciences, University of Glasgow G12 8QQ (United Kingdom); Davidson, A. [Scottish Universities Environmental Research Centre (SUERC), Rankine Avenue, East Kilbride G75 0QF (United Kingdom); Fifield, L.K. [Department of Nuclear Physics, Research School of Physical Sciences and Engineering, Australian National University, ACT 0200 (Australia); Freeman, S. [Scottish Universities Environmental Research Centre (SUERC), Rankine Avenue, East Kilbride G75 0QF (United Kingdom); Kim, J.Y. [Department of Geographical and Earth Sciences, University of Glasgow G12 8QQ (United Kingdom); Maden, C. [Scottish Universities Environmental Research Centre (SUERC), Rankine Avenue, East Kilbride G75 0QF (United Kingdom); Xu, S. [Scottish Universities Environmental Research Centre (SUERC), Rankine Avenue, East Kilbride G75 0QF (United Kingdom)

    2007-06-15

    The results of the first international inter-comparison of {sup 10}Be analysis from quartz are presented. This inter-comparison includes the sample preparation starting from pre-purified quartz and AMS measurements at SUERC and ANU. Measured {sup 10}Be concentrations agree within their uncertainties for six out of seven samples with {sup 10}Be concentrations greater than 1 x 10{sup 4} at/g quartz. This agreement and also the agreement of {sup 10}Be concentrations analysed from two aliquots of the same sample at SUERC indicate that addition of {sup 9}Be carrier before (used at ANU) or after quartz dissolution (used at SUERC apart from one aliquot of one sample) should not result in substantially different results.

  5. Quantitative Classification of Quartz by Laser Induced Breakdown Spectroscopy in Conjunction with Discriminant Function Analysis

    Directory of Open Access Journals (Sweden)

    A. Ali

    2016-01-01

    Full Text Available A responsive laser induced breakdown spectroscopic system was developed and improved for utilizing it as a sensor for the classification of quartz samples on the basis of trace elements present in the acquired samples. Laser induced breakdown spectroscopy (LIBS in conjunction with discriminant function analysis (DFA was applied for the classification of five different types of quartz samples. The quartz plasmas were produced at ambient pressure using Nd:YAG laser at fundamental harmonic mode (1064 nm. We optimized the detection system by finding the suitable delay time of the laser excitation. This is the first study, where the developed technique (LIBS+DFA was successfully employed to probe and confirm the elemental composition of quartz samples.

  6. ANIE: A Mathematical Algorithm for Automated Indexing of Planar Deformation Features in Shocked Quartz

    Science.gov (United States)

    Huber, M. S.; Ferrière, L.; Losiak, A.; Koeberl, C.

    2011-03-01

    A mathematical method of indexing planar deformation features in quartz and a Microsoft Excel macro for automated indexing is presented, allowing for more rapid and accurate results than the previously used manual method.

  7. Scaling Properties of Feldspar and Quartz in Micro-images of Ideal Granites

    Institute of Scientific and Technical Information of China (English)

    Xu Deyi; Ke Xianzhong; Xie Shuyun; Cheng Qiuming

    2008-01-01

    The properties of feldspar and quartze are studied in this article from a fractal point of view using gray-scale micro-images of granite samples collected at the Fangshan (房山) granite body in Hebei (河北) Province, China, which can be regarded as an ideal granite in the sense of Vistelius. We found that there exist power-law relationships between the eigenvalues of the gray-scale matrices and their ranks for the feldspar and quartz. The fractal model used here is a λ-R model similar to the N-λ model proposed by Qiuming Cheng in 2005. Meanwhile, we found that average variances for the gray-scale matrices of feldspar are larger than those of quartz on the same sections, and this may be useful for auto-identification of feldspar and quartz as well as other minerals.

  8. Synthesis of Calcium Silicate (Casio3) Using Calcium Fluoride, Quartz and Microbes

    National Research Council Canada - National Science Library

    B. Gopal Krishna; M. Jagannadha Rao

    2015-01-01

    .... In this paper, synthesis of calcium silicate (CaSiO3) using calcium fluoride (CaF2) and quartz (SiO2) under microbial environment in a laboratory is being adopted to produce the required material...

  9. Overcurrent protection of transformers. Part 2: Traditional and new fusing philosophies for small and large transformers

    Energy Technology Data Exchange (ETDEWEB)

    Cook, C. J.; Niemira, J. K.

    2003-07-01

    New and traditional fusing philosophies for protecting transformers are discussed. This second in a two-part paper covers selection criteria for a transformer-primary fuse to protect the transformer consistent with industry-accepted through-fault protection curves. Also covered are the principles of coordination as they relate to the proper selection of the primary-side fuse and power fuses and the principles underlying the protection of load-side conductors and cables. The critical nature of secondary fault protection on small three-phase transformers used on industrial, commercial, and institutional power systems, as well as small-to-medium size three-phase power transformers used in utility substations is emphasized, in view of the long lead time and expense involved in replacing these transformers. In contrast, no special protection recommendations are made for small-kVA overhead distribution transformers, since they are not considered likely to experience secondary faults, and the rare faults that do occur will not likely be detected and cleared by the primary fuse. Also of importance is the fact that these transformers are inexpensive and readily available. Overall, large fuse rating, used in combination with a tank-mounted surge arrester is recommended, because it can provide better transformer protection than the smaller fuse ratings traditionally employed. 4 refs., 2 tabs., 4 figs.

  10. Abrupt change point detection of annual maximum precipitation using fused lasso

    Science.gov (United States)

    Jeon, Jong-June; Sung, Jang Hyun; Chung, Eun-Sung

    2016-07-01

    Because the widely used Bayesian change point analysis (BCPA) is generally applied to the normal distribution, it cannot be freely used to the annual maximum precipitations (AMP) in South Korea. Therefore, this study proposed the fused lasso penalty function to detect the change point of AMP which can be generally fitted by using the Generalized Extreme Value (GEV) distribution in South Korea. First, four numerical experiments are conducted to compare the detection performances between BCPA and fused lasso method. As a result, fused lasso shows the superiority of the data generated by GEV distribution having skewness. The fused lasso method is applied to 63 weather stations in South Korea and then 17 stations having any change points from BCPA and the GEV fused lasso are analyzed. Similar to the numerical analyses, the GEV fused lasso method can delicately detect the change point of AMPs. After the change point, the means of AMPs did not go back to the previous. Alternately, BCPA can be stated to find variation points not change points because the means returned to their original values as time progressed. Therefore, it can be concluded that the GEV fused lasso method detects the change points of non-stationary AMPs of South Korea. This study can be extended to more extreme distributions for various meteorological variables.

  11. Osseointegration of Immediate Transalveolar Implants

    Directory of Open Access Journals (Sweden)

    Yoel González Beriau

    2016-02-01

    Full Text Available Background: osseointegration is critical to start prosthetic rehabilitation. Objective: to describe osseointegration of immediate transalveolar implants. Methods: a prospective case series study was conducted from January 2012 to December 2013. It included all patients (75 patients with 79 implants who attended the Prosthodontics service. Age, sex, osseointegration, cause of tooth loss, region of the implant, specific tooth, bone level and keratinized gingiva around the implant, were the variables studied. Frequency distribution and statistical analysis were used for data analysis. Results: females and patients aged 31 to 45 years predominated. Osseointegration was observed in 97.4% of the implants. Nearly all implants were placed in the premaxilla and posterior maxilla, specifically in the first bicuspids. In most patients, osseointegration with bone formation occurred at the implant collar and in the presence of completely keratinized tissue, with a statistically significant association between the two variables. Conclusion: rehabilitation treatment with this type of implant led to successful osseointegration in most cases studied.

  12. Looking at Dauphiné twins in vein quartz as a potential paleostress indicator

    Science.gov (United States)

    Sintubin, Manuel; Wenk, Hans-Rudolf

    2013-04-01

    Paleostress studies commonly call upon (1) a fault slip data inversion technique, (2) a calcite twin stress inversion technique, (3) recrystallized grain size piezometry for quartz, or (4) direct measurements of residual lattice strain. Recent advances in orientation imaging microscopy (OIM) using electron backscatter diffraction (EBSD) on a scanning electron microscope (SEM) have revealed that Dauphiné twinning is very common in quartz in naturally deformed quartz-bearing rocks in a wide range of tectonometamorphic conditions. It has long been known that mechanical Dauphiné twinning in quartz can be stress-induced. Based on the results of an extensive EBSD-OIM analysis on vein quartz, taken from well-studied early to late-orogenic veins in the High-Ardenne slate belt (Germany, Belgium), we explore the potential use of mechanical Dauphiné twins as a paleostress indicator, possibly completing our toolbox for reconstructing paleostresses in the Earth's crust. The vein quartz studied precipitated in low-grade tectonometamorphic conditions (~200-400°C), typical for the brittle-plastic transition zone at the base of the seismogenic crust (~7-15km). Quartz has only been weakly affected by low to moderate temperature (200 to 400°C) crystal-plastic deformation. The samples show grains with a high concentration of Dauphiné twin boundaries and others free of twin boundaries, thus being untwinned or completely twinned. This pattern depends on the crystallographic orientation. Twin boundaries are arrested by grain or subgrain boundaries, suggesting that Dauphiné twinning occurred on a pre-existing fabric that resulted from crystal-plastic deformation. An analysis of the orientation distribution of the rhombs in the twinned variant domains of individual quartz (sub-)grains reveals a particular preferred orientation of the poles to rhombs. We will discuss the possible significance of these observations with respect to paleostresses that may have caused the mechanical

  13. Thermal activation of OSL as a geothermometer for quartz grain heating during fault movements

    Energy Technology Data Exchange (ETDEWEB)

    Rink, W.J.; Toyoda, S.; Rees-Jones, J.; Schwarcz, H.P. [School of Geography and Geology, McMaster University, Hamilton, ON (Canada)

    1999-02-01

    In discussions of ESR dating of fault movements, there has been much debate whether zeroing of ESR signals is a mechanical shearing effect or caused by frictional heating. The OSL (optically stimulated luminescence) sensitivity of quartz is known to increase after heating. This thermal activation of dose response of the OSL in quartz should be useful as a geothermometer to test whether quartz particles in fault gouge had been heated. We tested the OSL sensitivities of quartz from fault gouge, and from a control (quartz grains from sandstone) and were able to show heat-induced enhancement of OSL sensitivity to a test dose. We observed that relative enhancement of OSL dose response (ratio of heated to unheated single aliquots) is significantly less for the finest grains (45-75 and 100-150 {mu}m) compared with coarser grains (150-250 {mu}m). These data are consistent with a model of zeroing of the quartz grains during faulting, by frictional heating localized to the grain boundaries, which would be expected to affect smaller grains more than large ones. This argues against a zeroing model in which the entire fault gouge is heated by friction. Higher laboratory preheating of sandstone quartz reduces between-aliquot variability of OSL dose response in the unheated grains to nearly zero. Unheated coarsest fault gouge grains displayed virtually no among-aliquot variability, whereas fine grains showed much larger between-aliquot variability; as with the quartz sand, variability dropped to near zero after laboratory heating, suggesting that fine grains in fault gouge have experienced a wide range of natural thermal histories during faulting. This may present a problem for ESR dating of fault gouge using the plateau method.

  14. Impurity distribution and reduction behaviour of quartz in the production of high purity silicon

    OpenAIRE

    Dal Martello, Elena

    2012-01-01

    The production of solar grade silicon is based on the use of expensive high purity carbon and quartz feedstock as well as various silicon refining techniques. Impurities in the feedstock materials enter the silicon during the carbothermic reduction of quartz. The knowledge of the impurity distribution/removal in the feedstock and in the carbothermic reduction process is necessary for targeting less pure and cheaper raw materials.The aim of the present study is to investigate the impurity dist...

  15. Evidence for warmer event from quartz grains in the soil of Grove Mountains, East Antarctica

    Institute of Scientific and Technical Information of China (English)

    Yan Xin; Li Xiaoli; Liu Xiaohan; Zhang Ru-fan

    2005-01-01

    The cold desert soil has been discovered at first time in southern ridgeof Mount Harding, Grove Mountains of interior East Antarctica Ice Sheet. Based on the micro structural observation, dominant characteristics of quartz grains include: distinct surface stria and fractures, and clean features of frost action at both of crystal margins and micro crannies of quartz grains. These features show a pedogenesis environment of few water, short transportation and frost action, revealing a warmer climatic event existed in this region.

  16. Influence of spectral interferences on the results of quartz determination by infrared spectrometry

    Directory of Open Access Journals (Sweden)

    Aleksandra Maciejewska

    2015-07-01

    Full Text Available Background: Determination of quartz by Fourier transform infrared spectrometry (FTIR is not specific: the obtained results are influenced by matrix components, some of which cause spectral interference. The aim of the study was to evaluate the effect of dust components responsible for spectral interference with quartz on the results of its determinations, and to develop methods to minimize the effects of interferences. Material and Methods: Investigation of interferent effects were conducted using respirable dusts: quartz SRM 1878a, cristobalite SRM 1879a, synthetic amorphous silica (Zeosil and feldspar, albite and kaolinite. For the study 17 mixtures with quartz and interferents at concentrations from 10 to 90% were prepared. Determinations of quartz were carried out by the KBr disc method. Results: In mixtures of quartz with interferents, the results based on bands 798–779 cm–1 were overestimated by 10–55%, while those based on band 695 cm–1 were closer to the true content of quartz. It was found that the best methods able to decrease the impact of spectral interference are: scaled subtraction of IR spectra of feldspar or kaolinite analysed in nonashed samples, correction curve for kaolinite also investigated in nonashed samples with quartz-content calculation based on band 695 cm–1 in mixtures with cristobalite, amorphous silica or kaolinite in ashed samples. Conclusions: The study indicates the need to identify spectral interferences in dust when determining crystalline silica by FT-IR and to take actions to minimize their impact on the obtained results. Med Pr 2015;66(4:497–509

  17. Surface iron inhibits quartz-induced cytotoxic and inflammatory responses in alveolar macrophages.

    Science.gov (United States)

    Ghiazza, Mara; Scherbart, Agnes M; Fenoglio, Ivana; Grendene, Francesca; Turci, Francesco; Martra, Gianmario; Albrecht, Catrin; Schins, Roel P F; Fubini, Bice

    2011-01-14

    The mechanism of enhancement/inhibition of quartz toxicity induced by iron is still unclear. Here the amount of iron on a fibrogenic quartz (Qz) was increased by wet impregnation (Fe(NO(3))(3) 0.67 and 6.7 wt %). X-ray diffraction (XRD), XRF diffuse reflectance, UV-vis, and infrared (IR) spectroscopies revealed dispersed ferric ions, and hematite aggregates at the higher loading. Surface features relevant to pathogenicity and cell responses were compared not only to the original quartz but also to reference quartz DQ12. Surface charge (ζ-potential) was more negative on the original and low-loaded specimen than on the high-loaded one. DQ12 had a less negative ζ-potential than Qz, ascribed to the absence of aluminium present in Qz (1.7 wt %). All quartz specimens were able to generate HO(•) radicals, iron-loaded samples being more reactive than original quartz. Iron deposition inhibited the rupture of a C-H bond. All quartzes were phagocytized by alveolar macrophages (AMΦ cell line NR8383) to the same extent, irrespective of their surface state. Conversely, iron loading increased AMΦ viability (evaluated by cytotoxicity and induction of apoptosis). Qz was found to be much less cytotoxic than DQ12. The induction of oxidative stress and inflammatory responses (evaluated by HO-1 mRNA expression and TNF-α mRNA and protein expression) revealed a reduction in inflammogenicity upon iron loading and a more inflammogenic potency of DQ12 ascribed to undissociated SiOH interacting via H-bonding with cell membrane components. The results suggest that besides aluminium also iron at the quartz surface may have an inhibitory effect on adverse health responses.

  18. The optical absorption of gamma irradiated and heat-treated natural quartz

    Directory of Open Access Journals (Sweden)

    Eduardo Henrique Martins Nunes

    2005-09-01

    Full Text Available Quartz with aluminum as impurity absorbs energy from ionizing radiation and modifies its color. Colorless quartz becomes smoky or dark smoky (morion quartz when exposed to gamma rays. By heat-treatment, smoky quartz may become successively greenish, yellowish, or brownish as the irradiation dose increases. Natural, colorless quartz is routinely colored by irradiation with gamma rays and heat-treatment for jewelry production. The color formation in natural quartz through this procedure is explained based on EPR, UV-VIS, and IR studies of irradiated and irradiated and heat-treated samples. Smoky quartz shows absorption bands in the visible region and a strong EPR signal. After heat-treatment it shows absorption bands in the near UV region with extensions into the visible region and a weak EPR signal. The intensity of the absorption bands is proportional to the irradiation dose. These changes of color are explained by the model of Itoh, Stoneham, and Stoneham. [AlSi O4 /h+]0 centers are produced by irradiation, causing the EPR signal and the absorption bands in the visible region. [AlSi O4]- centers are created from [AlSi O4 /h+]0 centers by heat-treatment. They cannot cause an EPR signal and have absorption bands in the near UV region with extensions into the visible region. The highest concentration of [AlSi O4]- centers occurs when the charge compensators have medium mobility. Lithium should give the best condition for color formation. Sodium (low mobility and hydrogen (high mobility should make smoky quartz colorless after heat-treatment.

  19. Deriving pedotransfer functions for soil quartz fraction in southern France from reverse modeling

    Science.gov (United States)

    Calvet, Jean-Christophe; Fritz, Noureddine; Berne, Christine; Piguet, Bruno; Maurel, William; Meurey, Catherine

    2016-12-01

    The quartz fraction in soils is a key parameter of soil thermal conductivity models. Because it is difficult to measure the quartz fraction in soils, this information is usually unavailable. This source of uncertainty impacts the simulation of sensible heat flux, evapotranspiration and land surface temperature in numerical simulations of the Earth system. Improving the estimation of soil quartz fraction is needed for practical applications in meteorology, hydrology and climate modeling. This paper investigates the use of long time series of routine ground observations made in weather stations to retrieve the soil quartz fraction. Profile soil temperature and water content were monitored at 21 weather stations in southern France. Soil thermal diffusivity was derived from the temperature profiles. Using observations of bulk density, soil texture, and fractions of gravel and soil organic matter, soil heat capacity and thermal conductivity were estimated. The quartz fraction was inversely estimated using an empirical geometric mean thermal conductivity model. Several pedotransfer functions for estimating quartz content from gravimetric or volumetric fractions of soil particles (e.g., sand) were analyzed. The soil volumetric fraction of quartz (fq) was systematically better correlated with soil characteristics than the gravimetric fraction of quartz. More than 60 % of the variance of fq could be explained using indicators based on the sand fraction. It was shown that soil organic matter and/or gravels may have a marked impact on thermal conductivity values depending on which predictor of fq is used. For the grassland soils examined in this study, the ratio of sand-to-soil organic matter fractions was the best predictor of fq, followed by the gravimetric fraction of sand. An error propagation analysis and a comparison with independent data from other tested models showed that the gravimetric fraction of sand is the best predictor of fq when a larger variety of soil types

  20. Stresses and pressures at the quartz-to-coesite phase transformation in shear deformation experiments

    Science.gov (United States)

    Richter, B.; Stünitz, H.; Heilbronner, R.

    2016-11-01

    Coesite was found in quartz aggregates, experimentally deformed at confining pressures of 1.0-1.5 GPa and temperatures between 600°C and 900°C. The confining pressure (Pc) and, in most cases, the mean stress (σm) of the experiments were below those of the quartz-to-coesite phase transformation. Yet coesite formed when the maximum principal stress (σ1) was within the P-T range of the coesite stability field. In one sample, the euhedral coesite grains were corroded indicating that coesite started to transform back to quartz. It is inferred that this sample started to deform with σ1 above the quartz-to-coesite phase transformation and, with ongoing deformation, σ1 decreased to values in the quartz stability field due to strain weakening. In all cases, σ1 triggered the quartz-to-coesite reaction as well as the reverse reaction, suggesting that σ1 is the critical parameter for the quartz-to-coesite transformation—not Pc or σm. With progressive deformation, the coesite laths rotated toward the shear plane as more rigid particles with the sense of shear. In case of back reaction, new quartz grains exhibit no systematic crystallographic relationship with respect to old coesite. The experiments cover different degrees of pressure "overstepping," different temperatures, and different experimental durations at P and T, and deformation always enhances the reaction kinetics. The observation that σ1 is critical for a pressure-dependent phase transformation (also for reversals) poses questions for the thermodynamic treatment of such phase transformations.