Evaluation report on CCTF core-II reflood test C2 - 8 (Run 67)

International Nuclear Information System (INIS)

Akimoto, Hajime; Iguchi, Tadashi; Okubo, Tsutomu; Murao, Yoshio; Okabe, Kazuharu; Sugimoto, Jun.

1987-01-01

In order to study the system pressure effect of the core cooling and flow behavior during the reflood phase of a PWR LOCA, a test was performed with CCTF under the system pressure pf 0.15 MPa as a counterpart test of the CCTF test C2-1 (system pressure 0.42 MPa) and the CCTF test C2-4 (system pressure 0.20 MPa). Through the comparisons of results from these three tests, the following conclusions were obtained: (1) The higher system pressure resulted in the lower temperature rise, the shorter turnaround time and the shorter quench time as observed in the CCTF Core-I system pressure effect tests. (2) The higher system pressure resulted in higher core water head, higher upper plenum water head, higher mass flow rate through the primary loops. On the other hand, the higher system pressure resulted in lower downcomer water head and lower pressure drop through the primary loops and the broken cold leg. These system pressure effects on the flow behavior in the primary system are almost the same as observed in the system pressure effect tests in the CCTF Core-I test series. (3) Before the mixture level in the upper plenum reached the level of the hot leg nozzle, the loop flow resistance coefficient of the intact loops was nearly constant regardless of the system pressure. After the mixture level reached the level of the hot leg nozzle, the loop flow resistance coefficient was increased due to the water accumulation in the hot leg piping and the inlet plenum of the steam generator in these tests. (J.P.N.)

Long-term corrosion tests of Ti{sub 3}SiC{sub 2} and Ti{sub 2}AlC in oxygen containing LBE at temperatures up to 700 °C

Energy Technology Data Exchange (ETDEWEB)

Heinzel, A., E-mail: Annette.heinzel@kit.edu; Weisenburger, A.; Müller, G.

2016-12-15

Two MAX-phase materials, Ti{sub 3}SiC and Ti{sub 2}AlC, were tested at 550 °C, 650 °C and 700 °C up to 10 000 h in LBE (lead-bismuth-eutectic) containing of 10{sup −6} and 10{sup −8} wt% oxygen. It was found that secondary phases have a strong influence on corrosion effects. Ti{sub 3}SiC showed a surface disintegration at 550°C/10{sup −6} wt% oxygen after longer exposure, while a 4–7 μm thick TiO{sub 2} layer with Pb-Bi inclusions was detected on Ti{sub 2}AlC. However, Ti{sub 3}SiC is protected by a double layered oxide with an outer part of TiO{sub 2} and a mixed inner layer of SiO{sub 2} and TiO{sub 2} at the higher temperatures. Ti{sub 2}AlC formed a TiO{sub 2} surface layer containing Al{sub 2}O{sub 3}. Some defects could be observed on the Ti{sub 3}SiC surface in LBE containing 10{sup −8} wt% oxygen at 550 °C and 650 °C. The secondary phases between the Ti{sub 3}SiC grains showed strong oxidation at 700 °C. Due to the high Al solubility in LBE, Ti{sub 2}AlC experienced strong dissolution attack after longer exposure times at 650 and 700 °C.

Quick look report for semiscale MOD-2C Test S-FS-11

International Nuclear Information System (INIS)

Plessinger, M.P.

1985-11-01

Results of a preliminary analysis of the fifth test performed in the Semiscale MOD-2C Steam Generator Feedwater and Steam Line Break (FS) experiment series are presented. Test S-FS-11 simulated a pressurized water reactor transient initiated by a 50% break in a steam generator bottom feedwater line downstream of the check valve. With the exception of primary pressure, the initial conditions represented the initial conditions used for the C-E System 80 Final Safety Analysis Report (FSAR) Appendix 15B calculations. The transient included an initial 600 s period in which only automatic plant protection systems responded to the initiating event. This period was followed by a series of operator actions necessary to stabilize the plant followed by break isolation and affected loop steam generator refill with auxiliary feedwater. The test results provided a measured evaluation of the effectiveness of the automatic responses in minimizing primary system overpressurization and operator actions in stabilizing the plant. Test data also provided a basis for comparison with other tests in the series of the effects of break size on primary overpressurization and primary-to-secondary heat transfer. 64 figs

Clinical investigation of 14C-urea breath test

International Nuclear Information System (INIS)

Yu Yongli; Zhu Ruisen; Ji Hong; Luo Quanyong

2000-01-01

To investigate clinical value of 14 C-urea breath test ( 14 C-UBT) for the diagnosis of Helicobacter pylori(Hp), 70 patients were both performed gastroscopy (taking gastric mucosae biopsy for rapid urease test and histology) and 14 C-UBT (some patients by Hp-IgG or DNAHp test also) within two days. The positive cases of both rapid urease test and histology was defined as 'gold standard' of Hp-positive, whereas the negative cases of both rapid urease test and histology as 'gold standard' of Hp-negative. The sensitivity of 14 C-UBT was 93.2%, the specificity 73.1%, and the diagnostic accuracy 85.7%. The difference (comparing with 'gold standard') was not marked (x 2 = 0.9 0.05(1) 2 = 3.84, P>0.05). But the diagnostic accuracy of 14 C-UBT (85.7%) and Hp-IgG (50%) had a marked difference (x 2 13.80>x 0.01(1) 2 = 6.64, P 14 C-UBT was easy to operate, reliable and suitable for clinical application

Understanding overpressure in the FAA aerosol can test by C3H2F3Br (2-BTP)✩

Science.gov (United States)

Linteris, Gregory Thomas; Babushok, Valeri Ivan; Pagliaro, John Leonard; Burgess, Donald Raymond; Manion, Jeffrey Alan; Takahashi, Fumiaki; Katta, Viswanath Reddy; Baker, Patrick Thomas

2018-01-01

Thermodynamic equilibrium calculations, as well as perfectly-stirred reactor (PSR) simulations with detailed reaction kinetics, are performed for a potential halon replacement, C3H2F3Br (2-BTP, C3H2F3Br, 2-Bromo-3,3,3-trifluoropropene), to understand the reasons for the unexpected enhanced combustion rather than suppression in a mandated FAA test. The high pressure rise with added agent is shown to depend on the amount of agent, and is well-predicted by an equilibrium model corresponding to stoichiometric reaction of fuel, oxygen, and agent. A kinetic model for the reaction of C3H2F3Br in hydrocarbon-air flames has been applied to understand differences in the chemical suppression behavior of C3H2F3Br vs. CF3Br in the FAA test. Stirred-reactor simulations predict that in the conditions of the FAA test, the inhibition effectiveness of C3H2F3Br at high agent loadings is relatively insensitive to the overall stoichiometry (for fuel-lean conditions), and the marginal inhibitory effect of the agent is greatly reduced, so that the mixture remains flammable over a wide range of conditions. Most important, the flammability of the agent-air mixtures themselves (when compressively preheated), can support low-strain flames which are much more difficult to extinguish than the easy-to extinguish, high-strain primary fireball from the impulsively released fuel mixture. Hence, the exothermic reaction of halogenated hydrocarbons in air should be considered in other situations with strong ignition sources and low strain flows, especially at preheated conditions. PMID:29628525

Cumulative damage fatigue tests on nuclear reactor Zircaloy-2 fuel tubes at room temperature and 3000C

International Nuclear Information System (INIS)

Pandarinathan, P.R.; Vasudevan, P.

1980-01-01

Cumulative damage fatigue tests were conducted on the Zircaloy-2 fuel tubes at room temperature and 300 0 C on the modified Moore type, four-point-loaded, deflection-controlled, rotating bending fatigue testing machine. The cumulative cycle ratio at fracture for the Zircaloy-2 fuel tubes was found to depend on the sequence of loading, stress history, number of cycles of application of the pre-stress and the test temperature. A Hi-Lo type fatigue loading was found to be very much damaging at room temperature and this feature was not observed in the tests at 300 0 C. Results indicate significant differences in damage interaction and damage propagation under cumulative damage tests at room temperature and at 300 0 C. Block-loading fatigue tests are suggested as the best method to determine the life-time of Zircaloy-2 fuel tubes under random fatigue loading during their service in the reactor. (orig.)

Journal of Earth System Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

Ata Allah Nadiri1 2 Asghar Asghari Moghaddam1 Frank T-C Tsai2 Elham Fijani1 2. Department of Geology, University of Tabriz, 29 Bahman Boulevard, Tabriz, East Azerbaijan, Iran. Department of Civil and Environmental Engineering, Louisiana State University, 3418G Patrick F. Taylor Hall, Baton Rouge, LA 70803, USA.

Engineering Macaca fascicularis cytochrome P450 2C20 to reduce animal testing for new drugs.

Science.gov (United States)

Rua, Francesco; Sadeghi, Sheila J; Castrignanò, Silvia; Di Nardo, Giovanna; Gilardi, Gianfranco

2012-12-01

In order to develop in vitro methods as an alternative to P450 animal testing in the drug discovery process, two main requisites are necessary: 1) gathering of data on animal homologues of the human P450 enzymes, currently very limited, and 2) bypassing the requirement for both the P450 reductase and the expensive cofactor NADPH. In this work, P450 2C20 from Macaca fascicularis, homologue of the human P450 2C8 has been taken as a model system to develop such an alternative in vitro method by two different approaches. In the first approach called "molecular Lego", a soluble self-sufficient chimera was generated by fusing the P450 2C20 domain with the reductase domain of cytochrome P450 BM3 from Bacillus megaterium (P450 2C20/BMR). In the second approach, the need for the redox partner and also NADPH were both obviated by the direct immobilization of the P450 2C20 on glassy carbon and gold electrodes. Both systems were then compared to those obtained from the reconstituted P450 2C20 monooxygenase in presence of the human P450 reductase and NADPH using paclitaxel and amodiaquine, two typical drug substrates of the human P450 2C8. The K(M) values calculated for the 2C20 and 2C20/BMR in solution and for 2C20 immobilized on electrodes modified with gold nanoparticles were 1.9 ± 0.2, 5.9 ± 2.3, 3.0 ± 0.5 μM for paclitaxel and 1.2 ± 0.2, 1.6±0.2 and 1.4 ± 0.2 μM for amodiaquine, respectively. The data obtained not only show that the engineering of M. fascicularis did not affect its catalytic properties but also are consistent with K(M) values measured for the microsomal human P450 2C8 and therefore show the feasibility of developing alternative in vitro animal tests. Copyright © 2012 Elsevier Inc. All rights reserved.

Study of necking stability in tension test of zircaloy-2, on range from 170 0 C to 620 0 C

International Nuclear Information System (INIS)

Okuda, M.Y.

1975-01-01

The objective of this work is to study necking behavior of Zircaloy-2 in a tension test in which the temperature range varies from 170 0 C to 620 0 C by means of a model. This model provides strain rate variations in the beginning of necking and the parameters in the / necking stability. A new parameter Ψ is presented which permits necking / stability description in metals by means of a simple tension test. It is also proceeded a behavioral study of ε versus ε curve after necking formation. (author)

Hemoglobin A1c (HbA1c) Test: MedlinePlus Lab Test Information

Science.gov (United States)

... page: https://medlineplus.gov/labtests/hemoglobina1chba1ctest.html Hemoglobin A1c (HbA1c) Test To use the sharing features on this page, please enable JavaScript. What is a hemoglobin A1c (HbA1c) test? A hemoglobin A1c (HbA1c) test measures ...

Thermal and electrochemical behaviour of C/Li xCoO 2 cell during safety test

Science.gov (United States)

Doh, Chil-Hoon; Kim, Dong-Hun; Kim, Hyo-Suck; Shin, Hye-Min; Jeong, Young-Dong; Moon, Seong-In; Jin, Bong-Soo; Eom, Seung Wook; Kim, Hyun-Soo; Kim, Ki-Won; Oh, Dae-Hee; Veluchamy, Angathevar

Thermal and electrochemical processes in a 1000 mAh lithium-ion pouch cell with a graphite anode and a Li xCoO 2 cathode during a safety test are examined. In overcharge tests, the forced current shifts the cell voltage to above 4.2 V. This causes a cell charged at the 1 C rate to lose cycleability and a cell charged at the 3 C rate to undergo explosion. In nail penetration and impact tests, a high discharge current passing through the cells gives rise to thermal runaway. These overcharge and high discharge currents promote joule heat within the cells and leads to decomposition and release of oxygen from the de-lithiated Li xCoO 2 and combustion of carbonaceous materials. X-ray diffraction analysis reveals the presence of Co 3O 4 in the cathode material of a 4.5 V cell heated to 400 °C. The major cathode product formed after the combustion process cells abused by forced current is Co 3O 4 and by discharge current the products are LiCoO 2 and Co 3O 4. The formation of a trace quantity of CoO through the reduction of Co 3O 4 by virtue of the reducing power of the organic solvent is also discussed.

Additional Value of CH4 Measurement in a Combined 13C/H2 Lactose Malabsorption Breath Test: A Retrospective Analysis

Science.gov (United States)

Houben, Els; De Preter, Vicky; Billen, Jaak; Van Ranst, Marc; Verbeke, Kristin

2015-01-01

The lactose hydrogen breath test is a commonly used, non-invasive method for the detection of lactose malabsorption and is based on an abnormal increase in breath hydrogen (H2) excretion after an oral dose of lactose. We use a combined 13C/H2 lactose breath test that measures breath 13CO2 as a measure of lactose digestion in addition to H2 and that has a better sensitivity and specificity than the standard test. The present retrospective study evaluated the results of 1051 13C/H2 lactose breath tests to assess the impact on the diagnostic accuracy of measuring breath CH4 in addition to H2 and 13CO2. Based on the 13C/H2 breath test, 314 patients were diagnosed with lactase deficiency, 138 with lactose malabsorption or small bowel bacterial overgrowth (SIBO), and 599 with normal lactose digestion. Additional measurement of CH4 further improved the accuracy of the test as 16% subjects with normal lactose digestion and no H2-excretion were found to excrete CH4. These subjects should have been classified as subjects with lactose malabsorption or SIBO. In conclusion, measuring CH4-concentrations has an added value to the 13C/H2 breath test to identify methanogenic subjects with lactose malabsorption or SIBO. PMID:26371034

Analysis of the FIST integral tests 4DBA1, 6SB2C and T1QUV with TRAC-BFl/v2001.2

International Nuclear Information System (INIS)

Analytis, G.Th.

2004-01-01

As part of the assessment of the frozen version of the PSU TRAC-BFl/v2001.2 and its qualification as a LB-LOCA and SB-LOCA code, in this work, we shall outline the comparisons between measurements and code predictions for three FIST tests: The LB-LOCA test 4DBA1, the SB-LOCA test 6SB2C and the failure to maintain water level test T1QUV. We shall study the effect of the number of axial levels in the active core as well as (in the case of the SB-LOCA test 6SB2C) the effect of the timing of the activation of the reflooding options/heat transfer package on the code predictions. Furthermore, we shall show that by using the upwinding option of some terms of the three-dimensional momentum equations, severe mass-error problems appearing in the analysis of the test T1QUV can be resolved. Generally, we shall show that although there are some differences between measurements and predictions, TRAC-BF1 captures quite well the overall behaviour of the LB-LOCA transient (depending on the number of axial nodes in the core) but underpredicts the rod surface temperatures of the SB-LOCA test 6SB2C

Comparison of the 1-gram [14C]xylose, 10-gram lactulose-H2, and 80-gram glucose-H2 breath tests in patients with small intestine bacterial overgrowth

International Nuclear Information System (INIS)

King, C.E.; Toskes, P.P.

1986-01-01

The sensitivity of three breath tests (1-g [ 14 C]xylose, 10-g lactulose-H 2 , and 80-g glucose-H 2 ) was studied in 20 subjects with culture-documented small intestine bacterial overgrowth. Elevated breath 14 CO2 levels were seen within 30 min of [ 14 C]xylose administration in 19 of 20 subjects with bacterial overgrowth and 0 of 10 controls. In contrast, H 2 breath tests demonstrated uninterpretable tests (absence of H 2 -generating bacteria) in 2 of 20 subjects with bacterial overgrowth and 1 of 10 controls and nondiagnostic increases in H 2 production in 3 of 18 glucose-H 2 and 7 of 18 lactulose-H 2 breath tests in subjects with bacterial overgrowth. These findings demonstrate continued excellent reliability of the 1-g [ 14 C]xylose breath test as a diagnostic test for bacterial overgrowth, indicate inadequate sensitivity of H 2 breath tests in detecting bacterial overgrowth, and suggest the need for evaluation of a 13 CO 2 breath test having the same characteristics as the [ 14 C]xylose test (avidly absorbed substrate having minimal contact with the colonic flora) for nonradioactive breath detection of bacterial overgrowth in children and reproductive-age women

Test-retest reproducibility of dopamine D{sub 2/3} receptor binding in human brain measured by PET with [{sup 11}C]MNPA and [{sup 11}C]raclopride

Energy Technology Data Exchange (ETDEWEB)

Kodaka, Fumitoshi [National Institute of Radiological Sciences, Molecular Neuroimaging Program, Molecular Imaging Center, Chiba (Japan); Jikei University School of Medicine, Department of Psychiatry, Tokyo (Japan); Ito, Hiroshi [National Institute of Radiological Sciences, Molecular Neuroimaging Program, Molecular Imaging Center, Chiba (Japan); National Institute of Radiological Sciences, Biophysics Program, Molecular Imaging Center, Chiba (Japan); Kimura, Yasuyuki; Fujie, Saori; Takano, Harumasa; Fujiwara, Hironobu; Sasaki, Takeshi; Suhara, Tetsuya [National Institute of Radiological Sciences, Molecular Neuroimaging Program, Molecular Imaging Center, Chiba (Japan); Nakayama, Kazuhiko [Jikei University School of Medicine, Department of Psychiatry, Tokyo (Japan); Halldin, Christer; Farde, Lars [Karolinska Institutet, Department of Clinical Neuroscience, Stockholm (Sweden)

2013-04-15

Dopamine D{sub 2/3} receptors (D{sub 2/3}Rs) have two affinity states for endogenous dopamine, referred to as high-affinity state (D{sub 2/3} {sup HIGH}), which has a high affinity for endogenous dopamine, and low-affinity state (D{sub 2/3} {sup LOW}). The density of D{sub 2/3} {sup HIGH} can be measured with (R)-2-{sup 11}CH{sub 3}O-N-n-propylnorapomorphine ([{sup 11}C]MNPA), while total density of D{sub 2/3} {sup HIGH} and D{sub 2/3} {sup LOW} (D{sub 2/3}Rs) can be measured with [{sup 11}C]raclopride using positron emission tomography (PET). Thus, the ratio of the binding potential (BP) of [{sup 11}C]MNPA to that of [{sup 11}C]raclopride ([{sup 11}C]MNPA/[{sup 11}C]raclopride) may reflect the proportion of the density of D{sub 2/3} {sup HIGH} to that of D{sub 2/3}Rs. In the caudate and putamen, [{sup 11}C]MNPA/[{sup 11}C]raclopride reflects the proportion of the density of D{sub 2} {sup HIGH} to that of D{sub 2}Rs. To evaluate the reliability of the PET paradigm with [{sup 11}C]MNPA and [{sup 11}C]raclopride, we investigated the test-retest reproducibility of non-displaceable BP (BP{sub ND}) measured with [{sup 11}C]MNPA and of [{sup 11}C]MNPA/[{sup 11}C]raclopride in healthy humans. Eleven healthy male volunteers underwent two sets of PET studies on separate days that each included [{sup 11}C]MNPA and [{sup 11}C]raclopride scans. BP{sub ND} values in the caudate and putamen were calculated. Test-retest reproducibility of BP{sub ND} of [{sup 11}C]MNPA and [{sup 11}C]MNPA/[{sup 11}C]raclopride was assessed by intra-subject variability (absolute variability) and test-retest reliability (intraclass correlation coefficient: ICC). The absolute variability of [{sup 11}C]MNPA BP{sub ND} was 5.30 {+-} 3.96 % and 12.3 {+-} 7.95 % and the ICC values of [{sup 11}C]MNPA BP{sub ND} were 0.72 and 0.82 in the caudate and putamen, respectively. The absolute variability of [{sup 11}C]MNPA/[{sup 11}C]raclopride was 6.11 {+-} 3.68 % and 11.60 {+-} 5.70 % and the ICC values of [{sup

Does Pharmacogenetic Testing for CYP450 2D6 and 2C19 among Patients with Diagnoses within the Schizophrenic Spectrum Reduce Treatment Costs?

DEFF Research Database (Denmark)

Herbild, Louise; Andersen, Stig Ejdrup; Werge, Thomas

2013-01-01

The effect of pharmacogenetic testing for CYP450 2D6 and 2C19 on treatment costs have not yet been documented. This study used Danish patient registers to calculate health care costs of treating patients with diagnoses within the schizophrenic spectrum for one year with or without pharmacogenetic...... testing for polymorphisms in the genes for the CYP2D6 and CYP2C19 enzymes. In a randomized, controlled trial, stratified with respect to metabolizer genotype, 104 patients were assigned to treatment based on pharmacogenetic testing and 103 patients to treatment as usual. Random exclusion of extensive...

BURNER RIG TESTING OF A500 C/SiC

Science.gov (United States)

2018-03-17

AFRL-RX-WP-TR-2018-0071 BURNER RIG TESTING OF A500® C /SiC Larry P. Zawada Universal Technology Corporation Jennifer Pierce UDRI...TITLE AND SUBTITLE BURNER RIG TESTING OF A500® C /SiC 5a. CONTRACT NUMBER In-House 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 62102F 6...test program characterized the durability behavior of A500® C /SiC ceramic matrix composite material at room and elevated temperature. Specimens were

Elastic properties of nanolaminar Cr_2AlC films and beams determined by in-situ scanning electron microscope bending tests

International Nuclear Information System (INIS)

Grieseler, Rolf; Theska, Felix; Stürzel, Thomas; Hähnlein, Bernd; Stubenrauch, Mike; Hopfeld, Marcus; Kups, Thomas; Pezoldt, Jörg; Schaaf, Peter

2016-01-01

The mechanical properties of Cr_2AlC MAX phase structures were investigated by in-situ bending tests. Freestanding structures such as cantilevers and doubly clamped beams of Cr_2AlC were produced. The structures exhibit a Young's modulus of 184 GPa which is close to the value obtained by vibrational measurements. The in-situ bending test allows the determination of the mechanical properties with a lower variance of the measurement results compared to the vibrational measurement. The results are a good starting point for the development of microelectromechanical structures based on MAX phases. - Highlights: • Cr_2AlC were produced by deposition multilayers and subsequent rapid annealing. • Freestanding doubly clamped beams and cantilevers of Cr_2AlC were prepared. • A finite elements model was implemented showing the displacement of the structure. • In-situ bending test at doubly clamped beams and cantilevers were performed. • An in-situ bending test is a valid approach to determine mechanical properties.

Multiple anion...π interactions in tris(1,10-phenanthroline-κ(2)N,N')iron(II) bis[1,1,3,3-tetracyano-2-(2-hydroxyethyl)propenide] monohydrate.

Science.gov (United States)

Setifi, Zouaoui; Domasevitch, Konstantin V; Setifi, Fatima; Mach, Pavel; Ng, Seik Weng; Petříček, Vaclav; Dušek, Michal

2013-11-01

In the ionic structure of the title compound, [Fe(C12H8N2)3](C9H5N4O2)2·H2O, the octahedral tris-chelate [Fe(phen)3](2+) dications [Fe-N = 1.9647 (14)-1.9769 (14) Å; phen is 1,10-phenathroline] afford one-dimensional chains by a series of slipped π-π stacking interactions [centroid-to-centroid distances = 3.792 (3) and 3.939 (3) Å]. The 1,1,3,3-tetracyano-2-(2-hydroxyethyl)propenide anions, denoted tcnoetOH(-), reveal an appreciable delocalization of π-electron density, involving the central propenide [C-C = 1.383 (3)-1.401 (2) Å] fragment and four nitrile groups, and this is also supported by density functional theory (DFT) calculations at the B97D/6-311+G(2d,2p) level. Primary noncovalent inter-moiety interactions comprise conventional O-H...O(N) and weak C-H...O(N) hydrogen bonding [O...O(N) = 2.833 (2)-3.289 (5) Å and C...O(N) = 3.132 (2)-3.439 (2) Å]. The double anion...π interaction involving a nitrile group of tcnoetOH(-) and two cis-positioned pyridine rings (`π-pocket') of [Fe(phen)3](2+) [N...centroid = 3.212 (2) and 3.418 (2) Å] suggest the relevance of anion...π stackings for charge-diffuse polycyanoanions and common M-chelate species.

Predictive value of 14CO2 breath tests for clinical use of 13CO2 breath tests

International Nuclear Information System (INIS)

Glaubitt, D.M.H.

1975-01-01

The knowledge of the efficiency of 14 CO 2 breath tests makes possible the comparison of the efficiency of analogous tests using the stable isotope 13 C. 14 CO 2 exhalation studies render overall information. After parenteral administration of a 14 C labeled substrate, 14 CO 2 breath tests permit insight into the metabolism of the 14 C substrate and the associated intermediary metabolism. If the 14 C substrate is given orally or by intraduodenal instillation, 14 CO 2 breath tests supply information not only about gastrointenstinal absorption and digestion but also about the intermediary metabolism yielding 14 CO 2 , after the administered substrate or its degradation products have been absorbed in the gastrointestinal tract. The fraction of 14 CO 2 arising from absorption, digestion and intermediary metabolism can be estimated only by additional methods. 14 CO 2 breath tests are unable to delineate single metabolic reactions involved in the formation of carbon dioxide. Under these considerations the clinical application of 14 CO 2 breath tests may provide diagnostically useful results, especially in internal medicine and surgery. The tests are suitable for intraindividual assessment of the course of a disease and of therapeutic effects. They may be important in the research of the metabolism of 14 C labeled substrates

Evaluation report on CCTF Core-II reflood test C2-16 (Run 76)

International Nuclear Information System (INIS)

Iguchi, Tadashi; Akimoto, Hajime; Okubo, Tsutomu; Hojo, Tsuneyuki; Murao, Yoshio; Sugimoto, Jun.

1987-03-01

This report presents the result of the upper plenum injection (UPI) test C2-16 (Run 76), which was conducted on October 23, 1984, with the Cylindrical Core Test Facility (CCTF) at Japan Atomic Energy Research Institute (JAERI). The CCTF is a 1/21.4 scale model of a 1,100 MWe PWR with four loop active components to provide information on the system and core thermo-hydrodynamics during reflood. The objectives of the test are to investigate the reflood phenomena with single failure UPI condition and to investigate the effect of the asymmetry of UPI on the reflood phenomena. The test was performed with an asymmetric UPI condition at the injection rate simulating single failure of LPCI pumps. It was observed that, (1) a UPI test simulating no LPCI pump failure gave the slightly lower peak clad temperature than a UPI test simulating single LPCI pump failure, indicating that single LPCI pump failure assumption is conserrative for UPI condition, and (2) an asymmetric UPI lead to a higher core water accumulation and then a higher heat transfer coefficient, resultantly a lower peak clad temperature than a symmetric UPI, indicating that asymmetric UPI does not lead to a poorer core cooling than symmetric UPI. (author)

Development of the light sensitivity of the clock genes Period1 and Period2, and immediate-early gene c-fos within the rat suprachiasmatic nucleus

Czech Academy of Sciences Publication Activity Database

Matějů, Kristýna; Bendová, Zdena; El-Hennamy, Rehab; Sládek, Martin; Sosniyenko, Serhiy; Sumová, Alena

2009-01-01

Roč. 29, č. 3 (2009), s. 490-501 ISSN 0953-816X R&D Projects: GA ČR(CZ) GA309/08/0503; GA MŠk(CZ) LC554 Grant - others:GA ČR(CZ) GD309/08/H079; EC(XE) LSH-2004-115-4-018741 Institutional research plan: CEZ:AV0Z50110509 Keywords : circadian clock * ontogenesis * photic entrainment Subject RIV: FH - Neuro logy Impact factor: 3.418, year: 2009

Hepatitis C Test

Science.gov (United States)

... and Prevention. Recommendations for the Identification of Chronic Hepatitis C Virus Infection Among Persons Born During 1945–1965. Prepared by ... Disease Control and Prevention. Vital Signs: Evaluation of Hepatitis C Virus Infection Testing and Reporting — Eight U.S. Sites, 2005–2011. ...

Characterization of 2D-C/C composite for application of very high temperature reactor

International Nuclear Information System (INIS)

Shibata, Taiju; Sumita, Junya; Kunimoto, Eiji; Sawa, Kazuhiro; Makita, Taiyo; Takagi, Takashi; Kim, W.J.; Jung, C.H.; Park, J.Y.

2010-01-01

For in-core components of VHTR (Very High Temperature Reactor), carbon fiber reinforced carbon matrix composite (C/C composite) is one of the major candidate materials. In this study, fracture behaviors of two dimensional (2D-) C/C composites were examined by SENB specimens with four-point bending test. The surface of specimens was observed by a CCD camera during the bending test, and observed by a stereomicroscope before and after the bending test. The following results were obtained through mode-I fracture test. (1) Three types of the composites were evaluated by tentatively using the stress intensity factor equation for metallic materials. The equivalent stress intensity factor of 2D-C/C composite is in the range of 5.9 - 10.0MPa m 1/2 . It was expected that the fracture mechanism for the composite materials could be assessed by this test method. (2) The crack opening displacement-load behavior of C/C composite might depend not only on the propagation of crack but also on delaminating between layers. (author)

Optoacoustic 13C-breath test analyzer

Science.gov (United States)

Harde, Hermann; Helmrich, Günther; Wolff, Marcus

2010-02-01

The composition and concentration of exhaled volatile gases reflects the physical ability of a patient. Therefore, a breath analysis allows to recognize an infectious disease in an organ or even to identify a tumor. One of the most prominent breath tests is the 13C-urea-breath test, applied to ascertain the presence of the bacterium helicobacter pylori in the stomach wall as an indication of a gastric ulcer. In this contribution we present a new optical analyzer that employs a compact and simple set-up based on photoacoustic spectroscopy. It consists of two identical photoacoustic cells containing two breath samples, one taken before and one after capturing an isotope-marked substrate, where the most common isotope 12C is replaced to a large extent by 13C. The analyzer measures simultaneously the relative CO2 isotopologue concentrations in both samples by exciting the molecules on specially selected absorption lines with a semiconductor laser operating at a wavelength of 2.744 μm. For a reliable diagnosis changes of the 13CO2 concentration of 1% in the exhaled breath have to be detected at a concentration level of this isotope in the breath of about 500 ppm.

In vivo assessment of the mitochondrial response to caloric restriction in obese women by the 2-keto[1-C]isocaproate breath test.

Science.gov (United States)

Parra, Dolores; González, Alvaro; Martínez, J Alfredo; Labayen, Idoia; Díez, Nieves

2003-04-01

The 2-keto[1-(13)C]isocaproate breath test has been proposed as a tool to detect mitochondrial dysfunction in alcoholic liver disease. The aim of this study was to evaluate if the 2-keto[1-(13)C]isocaproate breath test could detect in vivo dynamic changes on mitochondrial activity due to caloric restriction in obese women. Fifteen obese women (body mass index [BMI] > 30 kg/m(2)) participated in the study at baseline. Ten of these women agreed to participate on a diet program to induce body weight loss. Fifteen lean women (BMI keto[1-(13)C]isocaproate breath test and the plasma insulin (before diet: P =.863; after diet: P =.879), or leptin (before diet: P =.500; after diet: P =.637). In obese women before treatment, kilograms of fat free mass (P =.108), resting energy expenditure adjusted for body composition (P =.312), and the 2-keto[1-(13)C]isocaproate breath test (P =.205) were similar in comparison to lean women. However, 2-keto[1-(13)C]isocaproate oxidation tended to increase after dieting and was significantly higher than in controls (P =.015). These data suggest that the 2-keto[1-(13)C]isocaproate breath test reflected the adaptive modifications in mitochondrial oxidation in response to caloric restriction in obese women. Copyright 2003 Elsevier, Inc. All rights reserved.

Insulin C-peptide test

Science.gov (United States)

C-peptide ... the test depends on the reason for the C-peptide measurement. Ask your health care provider if ... C-peptide is measured to tell the difference between insulin the body produces and insulin someone injects ...

Fracture toughness testing of V-4Cr-4Ti at 25{degrees}C and -196{degrees}C

Energy Technology Data Exchange (ETDEWEB)

Li, H.X.; Kurtz, R.J. [Pacific Northwest National Lab., Richland, WA (United States)

1996-10-01

Measurements of the fracture toughness of the production-scale heat (832665) of V-4Cr-4Ti have been performed at 25{degrees}C and {minus}196{degrees}C using compact tension (CT) specimens. Test specimens were vacuum annealed at either 1000{degrees}C for 1 hour (HT1) or 1050{degrees}C for two hours (HT2). Specimens given the HT1 treatment were annealed after final machining, whereas the HT2 specimens received the 1050{degrees}C anneal at Teledyne Wah Chang prior to final machining. Following machining HT2 specimens were then vacuum annealed at 180{degrees}C for two hours to remove hydrogen. Specimens treated using HT1 had a partially recrystallized microstructure and those treated using HT2 had a fully recrystallized microstructure. The fracture toughness at 25{degrees}C was determined by J-integral tests and at {minus}196{degrees}C by ASTM E 399 type tests. Toughness values obtained at {minus}196{degrees}C were converted to J-integral values for comparison to the 25{degrees}C data. The 25{degrees}C fracture toughness was very high with none of the specimens giving valid results per ASTM criteria. Specimens fractured by microvoid coalescence. The fracture toughness at {minus}196{degrees}C was much lower than that at 25{degrees}C and the fracture surface showed predominantly cleavage features. The present results show a transition from ductile to brittle behavior with decreasing test temperature which is not observed from one-third scale Charpy impact tests. The fracture toughness at {minus}196{degrees}C was still quite high, however, at about 75 kJ/m{sup 2}. Delaminations in planes normal to the thickness direction were seen at both test temperatures. Fracture surfaces inside the delaminations exhibited nearly 100% cleavage facets. The cause of the brittle delaminations was not determined, but will be a subject for further investigation.

Implementation of Cell Samples as Controls in National Proficiency Testing for Clopidogrel Therapy-Related CYP2C19 Genotyping in China: A Novel Approach.

Directory of Open Access Journals (Sweden)

Guigao Lin

Full Text Available Laboratories are increasingly requested to perform CYP2C19 genetic testing when managing clopidogrel therapy, especially in patients with acute coronary syndrome undergoing percutaneous coronary intervention. To ensure high quality molecular testing and ascertain that the referring clinician has the correct information for CYP2C19 genotype-directed antiplatelet therapy, a proficiency testing scheme was set up to evaluate the laboratory performance for the entire testing process. Proficiency panels of 10 cell samples encompassing the common CYP2C19 genetic polymorphisms were distributed to 62 participating laboratories for routine molecular testing and the responses were analyzed for accuracy of genotyping and the reporting of results. Data including the number of samples tested, the accreditation/certification status, and test methodology of each individual laboratory were also reviewed. Fifty-seven of the 62 participants correctly identified the CYP2C19 variants in all samples. There were six genotyping errors, with a corresponding analytical sensitivity of 98.5% (333/338 challenges; 95% confidence interval: 96.5-99.5% and an analytic specificity of 99.6% (281/282; 95% confidence interval: 98.0-99.9%. Reports of the CYP2C19 genotyping results often lacked essential information. In conclusion, clinical laboratories demonstrated good analytical sensitivity and specificity; however, the pharmacogenetic testing community requires additional education regarding the correct reporting of CYP2C19 genetic test results.

Barriers to A1C testing among a managed care population.

Science.gov (United States)

Delaronde, Steven

2005-01-01

The purpose of this study is to explore reasons adults with diabetes do not receive at least 2 A1C tests per year as recommended by the American Diabetes Association (ADA). ConnectiCare, a regional managed care company based in Farmington, Connecticut, identified adult members with diabetes who did not have a medical claim for an A1C laboratory test from their physician. A questionnaire was sent to 740 randomly selected members asking them to report the number of A1C tests they received in the past 12 months and reasons for not receiving the number of tests recommended by the ADA. After sending an automated telephone reminder to nonrespondents, a 26% (n = 192) response rate was achieved. Thirty-three percent of respondents (n = 63) reported having diabetes and receiving fewer than 2 A1C tests in the past year. Respondents were equally divided between men and women, with a mean age of 58 years. The primary reasons given for not obtaining at least 2 A1C tests as recommended by the ADA were that respondents were unaware that the test is recommended (49%), not informed of the need for the test by their physician (38%), never heard of the A1C test (33%), and not seen regularly by their physician (19%). Diabetes self-management education remains an important means of encouraging adherence to important ADA recommendations such as regular A1C testing. Barriers to A1C testing can be addressed in multiple settings, including individual and group education, disease management programs, and physician education.

Gallium-cladding compatibility testing plan. Phases 1 and 2: Test plan for gallium corrosion tests. Revision 2

International Nuclear Information System (INIS)

Wilson, D.F.; Morris, R.N.

1998-05-01

This test plan is a Level-2 document as defined in the Fissile Materials Disposition Program Light-Water-Reactor Mixed-Oxide Fuel Irradiation Test Project Plan. The plan summarizes and updates the projected Phases 1 and 2 Gallium-Cladding compatibility corrosion testing and the following post-test examination. This work will characterize the reactions and changes, if any, in mechanical properties that occur between Zircaloy clad and gallium or gallium oxide in the temperature range 30--700 C

Evaluation report on CCTF core-II reflood test C2-6 (Run 64)

International Nuclear Information System (INIS)

Akimoto, Hajime; Iguchi, Tadashi; Sugimoto, Jun; Okubo, Tsutomu; Murao, Yoshio; Okabe, Kazuharu.

1985-03-01

In order to evaluate the effect of the radial power profile on the system behavior and the core thermal hydraulic behavior during the reflood phase of a PWR LOCA, a test was performed using the Cylindrical Core Test Facility(CCTF) with the flat radial power profile. The test was conducted with the same total core power as that of the steep radial power test C2-5(Run 63). Through the comparisons of the results from these two tests, the following conclusions were obtained: (1) The radial power profile in the core has weak effect on the thermal hydraulic behavior in the primary system except the core. (2) Almost the same differential pressure was observed at various elevations in the periphery of the core regardless of different radial power profile. The result suggests that the core differential pressure is determined mainly by the total power and the total stored energy rather than by the local power and the local stored energy. (3) The test results support the single channel core model with the average power rod used in the reactor safety analysis codes such as REFLA-1DS, WREM for the evaluation of the overall system behavior. (4) In the steep radial power test, the heat transfer coefficient in the central(high power) region was higher than that in the peripheral(low power) region. The tendency was not explained by the estimation with the heat transfer correlation developed by Murao and Sugimoto assuming that the void fraction was uniform in a horizontal cross section. It is necessary to study more the dependency of core heat transfer on the radial power profile in the wide core. (author)

Evaluation report on CCTF Core-II reflood Test C2-15 (Run 75)

International Nuclear Information System (INIS)

Okubo, Tsutomu; Iguchi, Tadashi; Akimoto, Hajime; Murao, Yoshio

1992-01-01

This report presents an evaluation on the CCTF Core-II Test C2-15 (Run 75). The purpose of the test is to investigate whether the thermo-hydrodynamic behavior is different between the CCTF and the FLECHT-SET reflooding tests. For this purpose, test conditions of the present test were set as close as possible to those of concerned FLECHT-SET 2714B experiment, taking account of differences in facility design. Investigating results of both the tests, the following conclusions are obtained: (1) Some discrepancies were observed in the measured test conditions between the two tests. Out of them, difference in the Acc injection duration was large and affected test results, such as the water accumulation in the downcomer and the core and the core cooling, during the initial period. However, this effect was found to become small with time. (2) Taking account of this difference and the difference in the broken cold leg pressure loss coefficient between the two facilities, the overall reflooding behavior is judged to be similar in the two facilities. (3) The CCTF test results showed the core heat transfer enhancement in the higher power region due to its steep radial power distribution, whereas the FLECHT-SET did not due to its rather flat radial power distribution. This enhancement was observed significantly at 1.83 m but was smaller at the higher elevation. (4) The heat transfer was nearly identical between the two tests and an existing correlation could well predict the heat transfer coefficients of both the tests at the location where the heat transfer enhancement mentioned above (3) were small, during the time period when the effect of the difference in the Acc injection mentioned above (1) were small. (5) Therefore, the core cooling is expected to be almost the same in the CCTF and the FLECHT-SET under the same core boundary conditions and core radial power distribution. (author)

Estimation of Insulin Resistance in Mexican Adults by the [13C]Glucose Breath Test Corrected for Endogenous Total CO2 Production

Directory of Open Access Journals (Sweden)

Erika Ibarra-Pastrana

2012-01-01

Full Text Available Objective. To evaluate the efficacy of the [13C]glucose breath test for measuring insulin resistance in Mexican adults with different glycemic states. Research Design and Methods. Fifty-eight adults underwent a [13C]glucose breath test with simultaneous measurement of total CO2 production by indirect calorimetry, at baseline and 90 minutes after the ingestion of 15 g of dextrose and 25 mg of [13C]glucose. HOMA was used as a marker of insulin resistance. Results. We found an inverse correlation between HOMA and the breath test δ13CO2 (‰, r=-0.41 (P=0.001. After adjusting for total CO2 production, correlations between HOMA and fasting glucose were less strong but remained significant. An ROC curve was constructed using δ13CO2 (‰ and HOMA values; the cut-off point was 9.99‰ δ13CO2, corresponding to a sensitivity of 80.0 (95% CI: 51.9, 95.7 and a specificity of 67.4 (95% CI: 51.5, 80.9. Conclusions. The [13C]glucose breath test is a simple noninvasive procedure but was not sufficiently robust for an accurate diagnosis of insulin resistance. Our findings suggest that the test might be helpful in identifying individuals who are not IR, which in turn may contribute to improved diabetes prevention.

Effect of alcohol consumption on the liver detoxication capacity as measured by [13C2]aminopyrine and L-[1-13C]phenylalanine breath tests.

Science.gov (United States)

Wutzke, Klaus D; Wigger, Marianne

2009-09-01

The aim of this study was to investigate the hepatic microsomal and cytosolic functions by using the 13CO2 breath test in healthy subjects either before or after consumption of red wine. Twelve adults received [13C2]aminopyrine and L-[1-13C]phenylalanine together with a standardised dinner. Expired air samples were taken over 6 h. After a wash-out period, the subjects consumed 0.4 ml ethanol per kg per day together with dinner over a 7.5-day period on average. Thereafter, 13C-tracer administration was repeated under identical conditions. The 13CO2 enrichments were measured by isotope ratio mass spectrometry. The mean cumulative percentage 13C-dose recovery after administration of [13C2]aminopyrine and L-[1-13C]phenylalanine either without or with red wine consumption amounted to 17.0+/-4.4 vs. 14.7+/-3.1% (p=0.170) and 14.0+/-2.8 vs. 11.5+/-3.9% (p=0.084), respectively. Moderate alcohol consumption does not induce significant short-term changes of the microsomal and the cytosolic function of the human liver in healthy subjects.

DECOVALEX III PROJECT. Thermal-Mechanical Modeling of the Yucca Mountain Project Drift Scale Test. Task 2B/2C Final Report

International Nuclear Information System (INIS)

Datta, Robin N.

2005-02-01

Tasks 2B and 2C deal with the mechanical process in the DST during the heating and cooling phases of the test. To model mechanical processes in the test it is necessary to have the time-evolution of temperature distributions in the test block which are inputs in the calculation of the mechanical effects. The difference between task 2B and 2C is that in 2B the mechanical effects are simulated using modeled temperature distributions as inputs, while in 2C the mechanical effects are calculated using measured temperature distributions as inputs. The given data include the results of geologic, thermal, mechanical, hydrologic, and mineralogic/petrologic characterization of the test block of the DST, the as-built configuration of the test block, including locations of various sensors and measuring instruments and the plans of heating and cooling, including expected heater powers at various times, respectively. The teams were required to predict the time-evolution of the displacements in the test block measured in the MPBX holes and the changes in the (fracture) permeability of the rock due to thermal mechanical processes, to be compared at certain time intervals. The research teams of ENRESA/UPC (Spain), DOE/LBNL (USA), CEA (France) and NRC/CNWRA (USA) participated the task 2B/2C with different numerical approaches and their reports are enclosed in the Attachments A-D, respectively. The DOE and ENRESA teams performed coupled THM analyses that included modeling of two-phase fluid flow (air and water), heat transfer (conduction and convection), and mechanical stress and strain, with dual-permeability and equivalent continuum approaches, respectively. CEA and NRC teams performed TM analyses in which the measured temperature field was imported to the numerical models. For simulation of rock-mechanical behavior, the DOE and ENRESA teams used elastic models, whereas CEA and NRC teams applied various elasto-plastic models. TM-induced permeability changes were modeled by DOE

Densities, viscosities, and refractive indexes for {C2H5CO2(CH2)2CH3+C6H13OH+C6H6} at T=308.15 K

International Nuclear Information System (INIS)

Casas, Herminio; Garcia-Garabal, Sandra; Segade, Luisa; Cabeza, Oscar.; Franjo, Carlos; Jimenez, Eulogio

2003-01-01

In this work we present densities, kinematic viscosities, and refractive indexes of the ternary system {C 2 H 5 CO 2 (CH 2 ) 2 CH 3 +C 6 H 13 OH+C 6 H 6 } and the corresponding binary mixtures {C 2 H 5 CO 2 (CH 2 ) 2 CH 3 +C 6 H 6 }, {C 2 H 5 CO 2 (CH 2 ) 2 CH 3 +C 6 H 13 OH}, and {C 6 H 13 OH+C 6 H 6 }. All data have been measured at T=308.15 K and atmospheric pressure over the whole composition range. The excess molar volumes, dynamic viscosity deviations, and changes of the refractive index on mixing were calculated from experimental measurements. The results for binary mixtures were fitted to a polynomial relationship to estimate the coefficients and standard deviations. The Cibulka equation has been used to correlate the experimental values of ternary mixtures. Also, the experimental values obtained for the ternary mixture were used to test the empirical methods of Kohler, Jacob and Fitzner, Colinet, Tsao and Smith, Toop, Scatchard et al., and Hillert. These methods predict excess properties of the ternary mixtures from those of the involved binary mixtures. The results obtained for dynamic viscosities of the binary mixtures were used to test the semi-empirical relations of Grunberg-Nissan, McAllister, Auslaender, and Teja-Rice. Finally, the experimental refractive indexes were compared with the predicted results for the Lorentz-Lorenz, Gladstone-Dale, Wiener, Heller, and Arago-Biot equations. In all cases, we give the standard deviation between the experimental data and that calculated with the above named relations

Test-retest reliability of {sup 11}C-ORM-13070 in PET imaging of α{sub 2C}-adrenoceptors in vivo in the human brain

Energy Technology Data Exchange (ETDEWEB)

Lehto, Jussi; Peltonen, Juha M.; Volanen, Iina; Scheinin, Mika [University of Turku, Clinical Research Services Turku CRST, Turku (Finland); TYKSLAB, Unit of Clinical Pharmacology, Turku (Finland); Virta, Jere R. [University of Turku and Turku University Hospital, Turku PET Centre, Turku (Finland); Turku University Hospital, Division of Clinical Neurosciences, Turku (Finland); Oikonen, Vesa; Roivainen, Anne; Luoto, Pauliina; Arponen, Eveliina; Helin, Semi; Virtanen, Kirsi [University of Turku and Turku University Hospital, Turku PET Centre, Turku (Finland); Hietamaeki, Johanna; Holopainen, Aila; Rouru, Juha; Sallinen, Jukka [Orion Pharma, Turku (Finland); Kailajaervi, Marita [Turku Imanet, GE Healthcare, Turku (Finland); Rinne, Juha O. [University of Turku and Turku University Hospital, Turku PET Centre, Turku (Finland); Turku University Hospital, Division of Clinical Neurosciences, Turku (Finland); University of Turku, Clinical Research Services Turku CRST, Turku (Finland)

2015-01-15

α{sub 2C}-Adrenoceptors share inhibitory presynaptic functions with the more abundant α{sub 2A}-adrenoceptor subtype, but they also have widespread postsynaptic modulatory functions in the brain. Research on the noradrenergic system of the human brain has been hampered by the lack of suitable PET tracers targeted to the α{sub 2}-adrenoceptor subtypes. PET imaging with the specific α{sub 2C}-adrenoceptor antagonist tracer [{sup 11}C]ORM-13070 was performed twice in six healthy male subjects to investigate the test-retest reliability of tracer binding. The bound/free ratio of tracer uptake relative to nonspecific uptake into the cerebellum during the time interval of 5 - 30 min was most prominent in the dorsal striatum: 0.77 in the putamen and 0.58 in the caudate nucleus. Absolute test-retest variability in bound/free ratios of tracer ranged from 4.3 % in the putamen to 29 % in the hippocampus. Variability was also <10 % in the caudate nucleus and thalamus. Intraclass correlation coefficients (ICC) ranged from 0.50 in the hippocampus to 0.89 in the thalamus (ICC >0.70 was also reached in the caudate nucleus, putamen, lateral frontal cortex and parietal cortex). The pattern of [{sup 11}C]ORM-13070 binding, as determined by PET, was in good agreement with receptor density results previously derived from post-mortem autoradiography. PET data analysis results obtained with a compartmental model fit, the simplified reference tissue model and a graphical reference tissue analysis method were convergent with the tissue ratio method. The results of this study support the use of [{sup 11}C]ORM-13070 PET in the quantitative assessment of α{sub 2C}-adrenoceptors in the human brain in vivo. Reliable assessment of specific tracer binding in the dorsal striatum is possible with the help of reference tissue ratios. (orig.)

Complement fixation test to C burnetii

Science.gov (United States)

... complement fixation test; Coxiella burnetii - complement fixation test; C burnetii - complement fixation test ... a specific foreign substance ( antigen ), in this case, C burnetii . Antibodies defend the body against bacteria, viruses, ...

Cardiomyocyte H9c2 cells present a valuable alternative to fish lethal testing for azoxystrobin

International Nuclear Information System (INIS)

Rodrigues, Elsa T.; Pardal, Miguel Â.; Laizé, Vincent; Cancela, M. Leonor; Oliveira, Paulo J.; Serafim, Teresa L.

2015-01-01

The present study aims at identifying, among six mammalian and fish cell lines, a sensitive cell line whose in vitro median inhibitory concentration (IC_5_0) better matches the in vivo short-term Sparus aurata median lethal concentration (LC_5_0). IC_5_0_s and LC_5_0 were assessed after exposure to the widely used fungicide azoxystrobin (AZX). Statistical results were relevant for most cell lines after 48 h of AZX exposure, being H9c2 the most sensitive cells, as well as the ones which provided the best prediction of fish toxicity, with a LC_5_0_,_9_6_h/IC_5_0_,_4_8_h = 0.581. H9c2 cell proliferation upon 72 h of AZX exposure revealed a LC_5_0_,_9_6_h/IC_5_0_,_7_2_h = 0.998. Therefore, identical absolute sensitivities were attained for both in vitro and in vivo assays. To conclude, the H9c2 cell-based assay is reliable and represents a suitable ethical alternative to conventional fish assays for AZX, and could be used to get valuable insights into the toxic effects of other pesticides. - Highlights: • Fish toxicity data are still considered standard information in ecotoxicology. • Alternatives to animal testing have become an important topic of research. • Cell-based assays are currently a promising in vitro alternative. • Comparative studies to accelerate the validation of cell-based methods are required. • H9c2 cell line proved to produce in vitro reliable toxicity results for azoxystrobin. - The application of cell-based assays for environmental toxicity studies would greatly reduce the number of fish needed for toxicity testing without any loss of reliability.

Evaluation report on CCTF core-II reflood test C2 - 18 (Run 78)

International Nuclear Information System (INIS)

Iguchi, Tadashi; Akimoto, Hajime; Okubo, Tsutomu; Murao, Yoshio; Sugimoto, Jun; Hojo, Tsuneyuki.

1987-03-01

This report presents the result of the upper plenum injection (UPI) test C2 - 18 (Run 78), which was conducted on November 13, 1984 with the Cylindrical Core Test Facility (CCTF) at Japan Atomic Energy Research Institute (JAERI). The CCTF is a 1/21.4 scale model of a 1,100 MWe PWR with four loop active components to provide information on the system and core thermo-hydrodynamics during reflood phase. The objectives of the test are to investigate the refill behavior with UPI condition and to investigate the reflood behavior with UPI Best-Estimate (BE) condition. The test was performed to simulate refill/reflood behavior with UPI and BE conditions (However, the LPCI flow rate was determined based on single failure of LPCI pumps.). The result of the test showed the followings. (1) Little special phenomena were recognized under UPI and BE conditions in comparison with those under UPI and Evaluation-Model (EM) conditions, although certain special phenoma (i.e. significant fluid oscillation) were recognized under Cold-Leg-Injection (CLI) and BE conditions in comparison with those under CLI and EM conditions. (2) Water inventory in lower plenum increased smoothly due to water injected into both upper plenum and cold leg during refill phase, similarly to that in refill-simulation test with CLI condition. Small difference in refill behavior with UPI condition is the existing of steam condensation in upper plenum, resulting in lower steam binding and higher core cooling during early reflood phase. This indicates the conservatism of UPI against CLI during early reflood phase. (3) The good core-cooling capability was confirmed under UPI and BE conditions. (author)

Knowledge and Outcome Measure of HbA1c Testing in Asian Indian Patients with Type 2 Diabetes from a Tertiary Care Center

Science.gov (United States)

Kumpatla, Satyavani; Medempudi, Srikanth; Manoharan, Deepa; Viswanathan, Vijay

2010-01-01

Aim: HbA1c test is considered to be the reliable measure for evaluating long-term glycemic control in type 2 diabetes. The purpose of this study was to evaluate whether knowledge about HbA1c test is associated with a better glycemic control. Materials and Methods: We conducted a cross-sectional survey of 480 (M:F; 287:193) adults with type 2 diabetes attending a tertiary care center during a period of four months. Baseline demographic and clinical data of all the subjects was obtained. Subject’s knowledge about HbA1c test and their target goal was assessed using a questionnaire. Recent HbA1c results were obtained from medical records. Results: Seventy four per cent of the subjects had awareness about HbA1c test and about 43% of those who knew HbA1c test also knew their target goal. 33% remember their last HbA1c result. The mean A1C of Group A was significantly lower when compared with Group B (8.1 ± 1.7 vs 9.2 ± 1.9, P<0.0001). Group C had lower A1C levels compared to Group D (7.7 ± 1.4 vs 8.5 ± 1.9, p<0.0001). Patients who kept their HbA1c less than 7% were significantly higher in Group C than in Group D. (37.8 vs 12.7%, p<0.00001). Subjects had good glycemic control with increasing levels of awareness about HbA1c. Conclusion: Majority of the diabetic patients who attended the tertiary care center for diabetes care knew HbA1c test and half of them were aware about their target goal. Awareness about HbA1c had a positive impact on maintenance of better glycemic control. PMID:20922109

Minimum bar size for flexure testing of irradiated SiC/SiC composite

International Nuclear Information System (INIS)

Youngblood, G.E.; Jones, R.H.

1998-01-01

This report covers material presented at the IEA/Jupiter Joint International Workshop on SiC/SiC Composites for Fusion structural Applications held in conjunction with ICFRM-8, Sendai, Japan, Oct. 23-24, 1997. The minimum bar size for 4-point flexure testing of SiC/SiC composite recommended by PNNL for irradiation effects studies is 30 x 6 x 2 mm 3 with a span-to-depth ratio of 10/1

Examination of C/C flat tile mock-ups with hypervapotron cooling after high heat flux testing

International Nuclear Information System (INIS)

Schedler, B.; Friedrich, T.; Traxler, H.; Eidenberger, E.; Scheu, C.; Clemens, H.; Pippan, R.; Escourbiac, F.

2007-01-01

Two C/C flat tile mock-ups with a hypervapotron cooling concept, have been successfully tested beyond ITER specification (3000 cycles at 15 MW/m 2 , 300 cycles at 20 MW/m 2 and 800-1000 cycles at 25 MW/m 2 ) in two electron beam testing facilities [F. Escourbiac, et al., Experimental simulation of cascade failure effect on tungsten and CFC flat tile armoured HHF components, Fusion Eng. Des., submitted for publication; F. Escourbiac, et al., A mature industrial solution for ITER divertor plasma facing components: hypervapotron cooling concept adapted to Tore Supra flat tile technology, Fusion Eng. Des. 75-79 (2005) 387-390]. Both mock-ups provide a SNECMA SEPCARB NS31 armour, which has been joined onto the CuCrZr heat sink by active metal casting (AMC) and electron beam welding (EBW). No tile detachment or sudden loss of single tiles has been observed; a cascade-like failure of flat tile armours was impossible to generate. At the maximum cyclic heat flux load of 25 MW/m 2 all tested tiles performed well except one, which revealed already a clear indication in the thermographic examination at the end of the manufacture. Visual examination and analysis of metallographic cuts of the remaining tiles demonstrated that the interface has not been altered. In addition, the shear strength of the C/C to copper joints measured after the high heat flux (HHF) test has been found to be still above the interlamellar shear strength of the used C/C material. The high resistance of the interface is explained by a modification of the C/C to copper joint interface due to silicon originating from the used C/C material

Examination of C/C flat tile mock-ups with hypervapotron cooling after high heat flux testing

Energy Technology Data Exchange (ETDEWEB)

Schedler, B. [Technology Centre of PLANSEE SE, A-6600 Reutte (Austria)], E-mail: bertram.schedler@plansee.com; Friedrich, T.; Traxler, H. [Technology Centre of PLANSEE SE, A-6600 Reutte (Austria); Eidenberger, E.; Scheu, C.; Clemens, H. [Department of Physical Metallurgy and Materials Testing, University of Leoben, A-8700 Leoben (Austria); Pippan, R. [Austrian Academy of Sciences, Erich-Schmid-Institute of Material Science, A-8700 Leoben (Austria); Escourbiac, F. [Association EURATOM-CEA, DSM/DRFC, CEA Cadarache, F-13108 St. Paul Lez Durance (France)

2007-04-15

Two C/C flat tile mock-ups with a hypervapotron cooling concept, have been successfully tested beyond ITER specification (3000 cycles at 15 MW/m{sup 2}, 300 cycles at 20 MW/m{sup 2} and 800-1000 cycles at 25 MW/m{sup 2}) in two electron beam testing facilities [F. Escourbiac, et al., Experimental simulation of cascade failure effect on tungsten and CFC flat tile armoured HHF components, Fusion Eng. Des., submitted for publication; F. Escourbiac, et al., A mature industrial solution for ITER divertor plasma facing components: hypervapotron cooling concept adapted to Tore Supra flat tile technology, Fusion Eng. Des. 75-79 (2005) 387-390]. Both mock-ups provide a SNECMA SEPCARB NS31 armour, which has been joined onto the CuCrZr heat sink by active metal casting (AMC) and electron beam welding (EBW). No tile detachment or sudden loss of single tiles has been observed; a cascade-like failure of flat tile armours was impossible to generate. At the maximum cyclic heat flux load of 25 MW/m{sup 2} all tested tiles performed well except one, which revealed already a clear indication in the thermographic examination at the end of the manufacture. Visual examination and analysis of metallographic cuts of the remaining tiles demonstrated that the interface has not been altered. In addition, the shear strength of the C/C to copper joints measured after the high heat flux (HHF) test has been found to be still above the interlamellar shear strength of the used C/C material. The high resistance of the interface is explained by a modification of the C/C to copper joint interface due to silicon originating from the used C/C material.

Compact toroid injection into C-2U

Science.gov (United States)

Roche, Thomas; Gota, H.; Garate, E.; Asai, T.; Matsumoto, T.; Sekiguchi, J.; Putvinski, S.; Allfrey, I.; Beall, M.; Cordero, M.; Granstedt, E.; Kinley, J.; Morehouse, M.; Sheftman, D.; Valentine, T.; Waggoner, W.; the TAE Team

2015-11-01

Sustainment of an advanced neutral beam-driven FRC for a period in excess of 5 ms is the primary goal of the C-2U machine at Tri Alpha Energy. In addition, a criteria for long-term global sustainment of any magnetically confined fusion reactor is particle refueling. To this end, a magnetized coaxial plasma-gun has been developed. Compact toroids (CT) are to be injected perpendicular to the axial magnetic field of C-2U. To simulate this environment, an experimental test-stand has been constructed. A transverse magnetic field of B ~ 1 kG is established (comparable to the C-2U axial field) and CTs are fired across it. As a minimal requirement, the CT must have energy density greater than that of the magnetic field it is to penetrate, i.e., 1/2 ρv2 >=B2 / 2μ0 . This criteria is easily met and indeed the CTs traverse the test-stand field. A preliminary experiment on C-2U shows the CT also capable of penetrating into FRC plasmas and refueling is observed resulting in a 20 - 30% increase in total particle number per single-pulsed CT injection. Results from test-stand and C-2U experiments will be presented.

Thermal fatigue behavior of C/C composites modified by SiC-MoSi2-CrSi2 coating

International Nuclear Information System (INIS)

Chu Yanhui; Fu Qiangang; Li Hejun; Li Kezhi

2011-01-01

Highlights: → The low-density C/C composites were modified by SiC-MoSi 2 -CrSi 2 multiphase coating by pack cementation. → The thermal fatigue behavior of the modified C/C composites was studied after undergoing thermal cycling for 20 times under the different environments. → The decrease of the flexural strength of the modified C/C composites during thermal cycle in air was primarily attributed to the partial oxidation of the modified C/C samples. - Abstract: Carbon/carbon (C/C) composites were modified by SiC-MoSi 2 -CrSi 2 multiphase coating by pack cementation, and their thermal fatigue behavior under thermal cycling in Ar and air environments was investigated. The modified C/C composites were characterized by scanning electron microscopy and X-ray diffraction. Results of tests show that, after 20-time thermal cycles between 1773 K and room temperature in Ar environment, the flexural strength of modified C/C samples decreased lightly and the percentage of remaining strength was 94.92%. While, after thermal cycling between 1773 K and room temperature in air for 20 times, the weight loss of modified C/C samples was 5.1%, and the flexural strength of the modified C/C samples reduced obviously and the percentage of remaining strength was only 75.22%. The fracture mode of modified C/C samples changed from a brittle behavior to a pseudo-plastic one as the service environment transformed from Ar to air. The decrease of the flexural strength during thermal cycle in air was primarily attributed to the partial oxidation of modified C/C samples.

Development of ASTM Standard for SiC-SiC Joint Testing Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Jacobsen, George [General Atomics, San Diego, CA (United States); Back, Christina [General Atomics, San Diego, CA (United States)

2015-10-30

As the nuclear industry moves to advanced ceramic based materials for cladding and core structural materials for a variety of advanced reactors, new standards and test methods are required for material development and licensing purposes. For example, General Atomics (GA) is actively developing silicon carbide (SiC) based composite cladding (SiC-SiC) for its Energy Multiplier Module (EM2), a high efficiency gas cooled fast reactor. Through DOE funding via the advanced reactor concept program, GA developed a new test method for the nominal joint strength of an endplug sealed to advanced ceramic tubes, Fig. 1-1, at ambient and elevated temperatures called the endplug pushout (EPPO) test. This test utilizes widely available universal mechanical testers coupled with clam shell heaters, and specimen size is relatively small, making it a viable post irradiation test method. The culmination of this effort was a draft of an ASTM test standard that will be submitted for approval to the ASTM C28 ceramic committee. Once the standard has been vetted by the ceramics test community, an industry wide standard methodology to test joined tubular ceramic components will be available for the entire nuclear materials community.

High performance Li3V2(PO4)3/C composite cathode material for lithium ion batteries studied in pilot scale test

International Nuclear Information System (INIS)

Chen Zhenyu; Dai Changsong; Wu Gang; Nelson, Mark; Hu Xinguo; Zhang Ruoxin; Liu Jiansheng; Xia Jicai

2010-01-01

Li 3 V 2 (PO 4 ) 3 /C composite cathode material was synthesized via carbothermal reduction process in a pilot scale production test using battery grade raw materials with the aim of studying the feasibility for their practical applications. XRD, FT-IR, XPS, CV, EIS and battery charge-discharge tests were used to characterize the as-prepared material. The XRD and FT-IR data suggested that the as-prepared Li 3 V 2 (PO 4 ) 3 /C material exhibits an orderly monoclinic structure based on the connectivity of PO 4 tetrahedra and VO 6 octahedra. Half cell tests indicated that an excellent high-rate cyclic performance was achieved on the Li 3 V 2 (PO 4 ) 3 /C cathodes in the voltage range of 3.0-4.3 V, retaining a capacity of 95% (96 mAh/g) after 100 cycles at 20C discharge rate. The low-temperature performance of the cathode was further evaluated, showing 0.5C discharge capacity of 122 and 119 mAh/g at -25 and -40 o C, respectively. The discharge capacity of graphite//Li 3 V 2 (PO 4 ) 3 batteries with a designed battery capacity of 14 Ah is as high as 109 mAh/g with a capacity retention of 92% after 224 cycles at 2C discharge rates. The promising high-rate and low-temperature performance observed in this work suggests that Li 3 V 2 (PO 4 ) 3 /C is a very strong candidate to be a cathode in a next-generation Li-ion battery for electric vehicle applications.

Experimental Durability Testing of 4H SiC JFET Integrated Circuit Technology at 727 C

Science.gov (United States)

Spry, David; Neudeck, Phil; Chen, Liangyu; Chang, Carl; Lukco, Dorothy; Beheim, Glenn M

2016-01-01

We have reported SiC integrated circuits (IC's) with two levels of metal interconnect that have demonstrated prolonged operation for thousands of hours at their intended peak ambient operational temperature of 500 C [1, 2]. However, it is recognized that testing of semiconductor microelectronics at temperatures above their designed operating envelope is vital to qualification. Towards this end, we previously reported operation of a 4H-SiC JFET IC ring oscillator on an initial fast thermal ramp test through 727 C [3]. However, this thermal ramp was not ended until a peak temperature of 880 C (well beyond failure) was attained. Further experiments are necessary to better understand failure mechanisms and upper temperature limit of this extreme-temperature capable 4H-SiC IC technology. Here we report on additional experimental testing of custom-packaged 4H-SiC JFET IC devices at temperatures above 500 C. In one test, the temperature was ramped and then held at 727 C, and the devices were periodically measured until electrical failure was observed. A 4H-SiC JFET on this chip electrically functioned with little change for around 25 hours at 727 C before rapid increases in device resistance caused failure. In a second test, devices from our next generation 4H-SiC JFET ICs were ramped up and then held at 700 C (which is below the maximum deposition temperature of the dielectrics). Three ring oscillators functioned for 8 hours at this temperature before degradation. In a third experiment, an alternative die attach of gold paste and package lid was used, and logic circuit operation was demonstrated for 143.5 hours at 700 C.

Diagnostic value of (1, 3)-β-D-glucan assay and galactomannan test for invasive fungal infection in patients of acute radiation sickness

International Nuclear Information System (INIS)

Wang Jing; Jiang Hongmei; Wang Jijun; Liu Yan; Zhao Wei; Ning Yongzhong; Zhang Jie; Ke Xiaoyan

2010-01-01

Objective: To investigate the diagnostic values of (1, 3)-β-D-glucan (G) and galactomannan (GM) for invasive fungal infection (IFI) in patients of acute radiation sickness (ARS). Methods: Samples of periogeral blood, pharyngeal secretion, urine, and feces were collected from 316 patients with ARS and suspected to suffer from IFI, 192 males and 124 females, aged 60.50 (1-96), with the underlying diseases of blood or respiration systems. Platelia Aspergillus EIA kit was used to detect the plasma BG (G test), and ELISA was used to detect the serum GM (GM test). Fungal culture and bacterial culture were performed. Results: The positive rates of G test, GM test, and fungal culture were 36.33%, 35.84%, and 34.18% respectively, but the positive rate of fungal culture of blood sample was 1-316 only. Pearson correlation analysis showed that G test, GM test and fungal culture test were positively correlated with IFI clinical diagnosis respectively (χ 2 =0.564, 0.357, 0.727, P<0.05). Conclusions: Easy to operate, rapid, and highly sencitive, G test and GM test can be used as adjunctive methods for early IFI diagnosis in ARS patients. (authors)

Influence of cytochrome 2C19 allelic variants on on-treatment platelet reactivity evaluated by five different platelet function tests.

Science.gov (United States)

Gremmel, Thomas; Kopp, Christoph W; Moertl, Deddo; Seidinger, Daniela; Koppensteiner, Renate; Panzer, Simon; Mannhalter, Christine; Steiner, Sabine

2012-05-01

The antiplatelet effect of clopidogrel has been linked to cytochrome P450 2C19 (CYP2C19) carrier status. The presence of loss of function and gain of function variants were found to have a gene-dose effect on clopidogrel metabolism. However, genotyping is only one aspect of predicting response to clopidogrel and several platelet function tests are available to measure platelet response. Patients and methods We studied the influence of CYP2C19 allelic variants on on-treatment platelet reactivity as assessed by light transmission aggregometry (LTA), the VerifyNow P2Y12 assay, the VASP assay, multiple electrode aggregometry (MEA), and the Impact-R in 288 patients after stenting for cardiovascular disease. Allelic variants of CYP2C19 were determined with the Infiniti® CYP450 2C19+ assay and categorized into four metabolizer states (ultrarapid, extensive, intermediate, poor). Platelet reactivity increased linearly from ultrarapid to poor metabolizers using the VerifyNow P2Y12 assay (P = 0.04), the VASP assay (P = 0.02) and the Impact-R (P = 0.04). The proportion of patients with high on-treatment residual platelet reactivity (HRPR) identified by LTA, the VerifyNow P2Y12 assay and the VASP assay increased when the metabolizer status decreased, while no such relationship could be identified for results of MEA and Impact-R. The presence of loss of function variants (*2/*2, *2-8*/wt, *2/*17) was an independent predictor of HRPR in LTA and the VASP assay while it did not reach statistical significance in the VerifyNow P2Y12 assay, MEA, and the Impact-R. Depending on the type of platelet function test differences in the association of on-treatment platelet reactivity with CYP2C19 carrier status are observed. Copyright © 2011 Elsevier Ltd. All rights reserved.

Volatility study of [C1C1im][NTf2] and [C2C3im][NTf2] ionic liquids

International Nuclear Information System (INIS)

Rocha, Marisa A.A.; Ribeiro, Filipe M.S.; Schröder, Bernd; Coutinho, João A.P.; Santos, Luís M.N.B.F.

2014-01-01

Highlights: • Vapor pressures of [C 1 C 1 im][NTf 2 ] and [C 2 C 3 im][NTf 2 ] ionic liquids are reported. • [C 1 C 1 im][NTf 2 ] presents higher enthalpy and entropy of vaporization than expected. • The high volatility of [C 2 C 3 im][NTf 2 ] is a result from its asymmetric character. -- Abstract: Vapor pressures of 1,3-dimethylimidazolium bis(trifluoromethylsulfonyl)imide, ([C 1 C 1 im][NTf 2 ]) and 1-ethyl-3-propylimidazolium bis(trifluoromethylsulfonyl)imide, ([C 2 C 3 im][NTf 2 ]) ionic liquids were measured as a function of temperature using a Knudsen effusion apparatus combined with a quartz crystal microbalance. Enthalpies and entropies of vaporization were derived from the fitting of vapor pressure and temperature results to the Clarke and Glew equation. [C 1 C 1 im][NTf 2 ] presents a higher enthalpy and entropy of vaporization than the neighboring members of the series. The enthalpy of vaporization of [C 2 C 3 im][NTf 2 ] lies in between the asymmetric and symmetric ionic liquid series, reflecting a decrease in the electrostatic interactions due to a decrease of the charge accessibility between the ionic pairs when the methyl group is replaced by an ethyl group. The obtained higher volatility of [C 2 C 3 im][NTf 2 ] arises from its asymmetric character, leading to an higher entropic contribution that compensates the enthalpic penalty. The border conditions ([C 1 C 1 im][NTf 2 ], [C 2 C 1 im][NTf 2 ] and [C 2 C 2 im][NTf 2 ]), topology ([C 2 C 3 im][NTf 2 ]) and symmetry/asymmetry of the ILs effect were evaluated and rationalized based on a comparative analysis of the thermodynamic properties, enthalpies and entropies of vaporization

Radiochemical synthesis of 3-(4-[18F] Fluorophenyl)-8-hydroxy-1, 2, 3, 4-tetrahydrochromeno [3, 4-c] pyridin-5-one: A putative dopamine D$4 receptor PET imaging agent

International Nuclear Information System (INIS)

Li, G.C.; Yin, D.Z.; Wang, M.W.; Cheng, D.F.; Wang, Y.X.

2005-01-01

Introduction: The dopamine D 4 receptor has lately received increasing interest since it has been hypothesized to be involved in the pathology and pharmacotherapy of schizophrenia. While this receptor is expressed in lower density in various extrastriatal brain regions and its distribution is still unclear due to the lack of suitable imaging agent and its level change in schizophrenia is controversial. Herein, based on the structure-activity analysis of chromeno[3, 4-c]pyridine- 5-ones as potential dopamine D 4 receptor ligands, a putative D 4 subtype positron emission tomography (PET) radioligand, 3-(4-[ 18 F]fluorophenyl)-8-hydroxy-1, 2, 3, 4-tetrahydrochromeno [3, 4-c]pyridin-5-one ([ 18 F]FHTP), was designed and synthesized. Methods: The radiochemical synthesis route was shown in Figure 1. [ 18 F]Fluoride was produced with a Cyclone-30 (IBA, Belgium) by 18 O(p, n) 18 F reaction using enriched 18 O-H 2 O and eluted from a Dowex 1-X8 anion-exchange column with aqueous potassium carbonate (20 mg/mL). 4-[ 18 F]Fluorobenzaldehyde was prepared according to the method reported by Alan A. Wilson and et al.. Then, 8-hydroxy-1, 2, 3, 4-tetrahydrochromeno [3, 4-c]pyridin-5-one, sodium cyanoborohydride, methanol and acetic acid were added to the dry residue, The mixture was then sealed and heated at 120 degree C for 12 min. At the end of the reaction, the mixture was cooled, diluted with ethyl acetate and washed with water. The extracted organic layer was passed through a small anhydrous magnesium sulfate column. After removal of the solvents in the mixture at 50 degree C under a stream of nitrogen, the obtained residue was redissolved in methanol and purified with a semi-preparative HPLC system, then the desired product was collected. Results: The radiochemical synthesis of [ 18 F]FHTP took around 110 min at EOS with an overall radiochemical yield 19% (decay-corrected) and its radiochemical purity was higher than 95%. Conclusion: A presumed dopamine D 4 receptor PET

Validation of clinical testing for warfarin sensitivity: comparison of CYP2C9-VKORC1 genotyping assays and warfarin-dosing algorithms.

Science.gov (United States)

Langley, Michael R; Booker, Jessica K; Evans, James P; McLeod, Howard L; Weck, Karen E

2009-05-01

Responses to warfarin (Coumadin) anticoagulation therapy are affected by genetic variability in both the CYP2C9 and VKORC1 genes. Validation of pharmacogenetic testing for warfarin responses includes demonstration of analytical validity of testing platforms and of the clinical validity of testing. We compared four platforms for determining the relevant single nucleotide polymorphisms (SNPs) in both CYP2C9 and VKORC1 that are associated with warfarin sensitivity (Third Wave Invader Plus, ParagonDx/Cepheid Smart Cycler, Idaho Technology LightCycler, and AutoGenomics Infiniti). Each method was examined for accuracy, cost, and turnaround time. All genotyping methods demonstrated greater than 95% accuracy for identifying the relevant SNPs (CYP2C9 *2 and *3; VKORC1 -1639 or 1173). The ParagonDx and Idaho Technology assays had the shortest turnaround and hands-on times. The Third Wave assay was readily scalable to higher test volumes but had the longest hands-on time. The AutoGenomics assay interrogated the largest number of SNPs but had the longest turnaround time. Four published warfarin-dosing algorithms (Washington University, UCSF, Louisville, and Newcastle) were compared for accuracy for predicting warfarin dose in a retrospective analysis of a local patient population on long-term, stable warfarin therapy. The predicted doses from both the Washington University and UCSF algorithms demonstrated the best correlation with actual warfarin doses.

Lessons Learned (3 Years of H2O2 Propulsion System Testing Efforts at NASA's John C. Stennis Space Center)

Science.gov (United States)

Taylor, Gary O.

2001-01-01

John C. Stennis Space Center continues to support the Propulsion community in an effort to validate High-Test Peroxide as an alternative to existing/future oxidizers. This continued volume of peroxide test/handling activity at Stennis Space Center (SSC) provides numerous opportunities for the SSC team to build upon previously documented 'lessons learned'. SSC shall continue to strive to document their experience and findings as H2O2 issues surface. This paper is intended to capture all significant peroxide issues that we have learned over the last three years. This data (lessons learned) has been formulated from practical handling, usage, storage, operations, and initial development/design of our systems/facility viewpoint. The paper is intended to be an information type tool and limited in technical rational; therefore, presenting the peroxide community with some issues to think about as the continued interest in peroxide evolves and more facilities/hardware are built. These lessons learned are intended to assist industry in mitigating problems and identifying potential pitfalls when dealing with the requirements for handling high-test peroxide.

Synthesis of [2-13C, 2-14C] 2-aminoethanol, [1-13C, 1-14C] 2-chloroethylamine, N,N'-bis([1-13C, 1-14C] 2-chloroethyl)-N-nitrosourea(BCNU) and N-([1-13C, 1-14C] 2-chloroethyl)-N-nitrosourea(CNU)

International Nuclear Information System (INIS)

Narayan, R.; Chang, C-j.

1982-01-01

[2- 13 C, 2- 14 C]2-Aminoethanol hydrochloride was prepared in good yield from Na*CN in a two step sequence by first converting the Na*CN to OHCH 2 *CN and then reducing the nitrile directly with a solution of borane-tetrahydrofuran complex. The reaction procedure was simple and the pure product could be obtained readily. Using this specifically labelled precursor, the synthesis of [1- 13 C, 1- 14 C]2-chloroethylamine hydrochloride, N-([1- 13 C, 1- 14 C]2-chloroethyl)-N-nitrosourea(CNU) and N,N'-bis([1- 13 C, 1- 14 C]2-chloroethyl)-N-nitrosourea(BCNU) in good yield without isotope scrambling was also reported. (author)

Leach testing of SYNROC and glass samples at 85 and 200/degree/C

International Nuclear Information System (INIS)

Oversby, V.M.; Ringwood, A.E.

1981-01-01

Leach tests were conducted on 0.5 g disc samples of SYNROC and two glass types using distilled water at 85 and 200/degree/C. No leaching was detected for SYNROC at either temperature. Thus, the upper limit on leach rate for SYNROC is <0.005 g/m/sup 2/d. Waste glass PNL 76-68 had leach rates of 1.4 g/m/sup 2/ d at 85/degree/C and 8.9 g/m/sup 2/ d at 200/degree/C, while 73-1 glass frit had a leach rate of 41 g/m/sup 2/ d at 200/degree/C. The leach tests were repeated in the presence of rock powders. Again, no leaching was measurable for SYNROC. PNL 76-68 glass had leach rates between 4 and 23 g/m/sup 2/ d at 200/degree/C and 73-1 frit leached at rates between 29 and 176 g/m/sup 2/ d at 200/degree/C. Tests were also conducted on crushed glass samples (PNL 76-68, 100-200 /mu/m size fraction). Bulk leach rates were calculated based on measurement of Ca, Cs, and U in the leach solutions. The results of the leach tests show that SYNROC is several orders of magnitude more resistant to leaching than glass

14C-urea breath test for the detection of Helicobacter pylori

International Nuclear Information System (INIS)

Veldhuyzen van Zanten, S.J.; Tytgat, K.M.; Hollingsworth, J.; Jalali, S.; Rshid, F.A.; Bowen, B.M.; Goldie, J.; Goodacre, R.L.; Riddell, R.H.; Hunt, R.H.

1990-01-01

The high urease activity of Helicobacter pylori can be used to detect this bacterium by noninvasive breath tests. We have developed a 14 C-urea breath test which uses 5 microCi 14 C with 50 mg nonradioactive urea. Breath samples are collected at baseline and every 30 min for 2 h. Our study compared the outcome of the breath test to the results of histology and culture of endoscopically obtained gastric biopsies in 84 patients. The breath test discriminated well between the 50 positive patients and the 34 patients negative for Helicobacter pylori: the calculated sensitivity was 100%, specificity 88%, positive predictive value 93%, and negative predictive value 100%. Treatment with bismuth subsalicylate and/or ampicillin resulted in lower counts of exhaled 14 CO 2 which correlated with histological improvement in gastritis. The 14 C-urea breath test is a better gold standard for the detection of Helicobacter pylori than histology and/or culture

Thermal shock test of TiC and graphite

International Nuclear Information System (INIS)

Shirakawa, H.; Okamura, J.; Son, P.; Miyake, M.

1989-01-01

Thermal shock tests were performed by pulse electron beam heating on chemically vapor deposited coatings of TiC on Poco graphite, bulk TiC, and several kinds of isotropic graphite. The specimens were heated at various power densities (10-45 MW/m 2 ) for various pulse durations (1-2 s) to examine the dependence of thermal failures on heating conditions. The TiC coating on graphite suffered cracking, surface melting and evaporation by the thermal pulse. The surface melting limit, defined as F τ 1/2 , where F is the minimum power density that causes surface melting for a specified pulse duration τ, was approximately 48 MWs 1/2 /m 2 for the TiC coating. The combined-Carbon/Titanium ratio of the coating after electron beam heating decreased with increasing power density and pulse duration. The bulk TiC specimens were so brittle that they fractured at heat load conditions where the coating showed no damage. The graphite specimens showed sublimation as a principal damage mechanism by the thermal pulse, and the sublimation weight loss decreased with increasing the thermal conductivity of the specimen. It was confirmed that the TiC coating on graphite had favorable resistance to thermal shock as compared to the bulk TiC and that graphite with high thermal conductivity is promising material as a high heat flux component. (orig.)

Initial testing of TiB2 and TiC coated limiters in ISX-B

International Nuclear Information System (INIS)

Langley, R.A.; Emerson, R.A.; Whitley, J.B.; Mullendore, A.W.

1980-01-01

Low-Z coatings on graphite substrates have been developed for testing as limiters in the Impurity Study Experiment (ISX-B) tokamak. Laboratory and tokamak testings have been accomplished. The laboratory tests included thermal shock experiments by means of pulsed e-beam irradiation, arcing experiments, and hydrogen and xenon ion erosion experiments. The tokamak testing consisted of ohmically heated plasma exposures with energy depositions up to 10 kJ/discharge on the limiters. The coatings, applied by chemical vapor deposition, consisted of TiB 2 and TiC deposited on POCO graphite substrates. The limiter samples were interchanged through the use of a transfer chamber without atmospheric exposure of the ISX-B tokamak. Limiter samples were baked out in the transfer chamber before use in the tokamak. Provisions for both heating and cooling the limiter during tokamak discharge were made. Initial testing of the limiter samples consisted of exposure to only ohmically heated plasma; subsequent testing will be performed in neutral-beam-heated plasmas having up to 3 MW of injected power. Bulk and surface temperatures of the samples were measured to allow the determination of energy deposition. Extensive plasma and edge diagnostics were used to evaluate the effect of the limiter on the plasma (e.g. vacuum ultraviolet spectrometry to determine plasma impurity concentrations, Thomson scattering to determine Z effective, IR camera to measure limiter surface temperature, and laser fluorescence spectrometry to determine neutral impurity concentration and velocity distribution in the limiter region). (orig.)

Performance of ProEx C and PreTect HPV-Proofer E6/E7 mRNA tests in comparison with the hybrid capture 2 HPV DNA test for triaging ASCUS and LSIL cytology.

Science.gov (United States)

Alaghehbandan, Reza; Fontaine, Daniel; Bentley, James; Escott, Nicholas; Ghatage, Prafull; Lear, Adrian; Coutlee, Francois; Ratnam, Samuel

2013-09-01

The clinical usefulness of the ProEx C (Becton Dickinson) and PreTect HPV-Proofer E6/E7 mRNA tests (Proofer; Norchip) for the triage of ASCUS and LSIL cytology was determined in comparison with the Hybrid Capture 2 HPV DNA test (HC2; Qiagen). The study population consisted of women with a history of abnormal cytology referred to colposcopy. Histology-confirmed CIN 2+ served as the disease endpoint. The study was based on 1,360 women (mean age 30.7 years), of whom 380 had CIN 2+. Among 315 with ASCUS (CIN 2+, n = 67), the sensitivities of ProEx C, Proofer, and HC2 to detect CIN 2+ were, 71.6, 71.6, and 95.5%, respectively, with a corresponding specificity of 74.6, 74.2, and 35.1%. Among 363 with LSIL (CIN 2+, n = 108), the sensitivities of ProEx C, Proofer, and HC2 were, 67.6, 74.1, and 96.3%, respectively, with a corresponding specificity of 60, 68.2, and 18.4%. Among 225 HC2-positive ASCUS (CIN 2+, n = 64), 105 tested positive by ProEx C, reducing colposcopy referral by 53.3% and detecting 71.9% of CIN 2+; Proofer was positive in 112/225, reducing colposcopy referral by 50.2% and detecting 75.0% of CIN 2+. Among 312 HC2-positive LSIL (CIN 2+, n = 104), 160 tested positive by ProEx C, reducing coloposcopy referral by 48.7% and detecting 66.3% of CIN 2+; Proofer was positive in 159/312, reducing colposcopy referral by 49.0% and detecting 75.0% of CIN 2+. In conclusion, both ProEx C and Proofer have a similar performance profile with a significantly higher specificity but lower sensitivity than HC2 for the detection of CIN 2+. Consequently, although they can reduce colposcopy referral, they will miss a proportion of CIN 2+ cases. This is a major limitation and should be taken into account if these tests are considered for ASCUS or LSIL triage. Copyright © 2012 Wiley Periodicals, Inc., a Wiley company.

14C-urea breath test for the detection of Helicobacter pylori

NARCIS (Netherlands)

Veldhuyzen van Zanten, S. J.; Tytgat, K. M.; Hollingsworth, J.; Jalali, S.; Rshid, F. A.; Bowen, B. M.; Goldie, J.; Goodacre, R. L.; Riddell, R. H.; Hunt, R. H.

1990-01-01

The high urease activity of Helicobacter pylori can be used to detect this bacterium by noninvasive breath tests. We have developed a 14C-urea breath test which uses 5 microCi 14C with 50 mg nonradioactive urea. Breath samples are collected at baseline and every 30 min for 2 h. Our study compared

Alkali/TX sub 2 catalysts for CO/H sub 2 conversion to C sub 1 -C sub 4 alcohols

Energy Technology Data Exchange (ETDEWEB)

Klier, K.; Herman, R. G.; Bastian, R.

1990-01-01

The objective of this research is to investigate and develop novel catalysts for the conversion of coal-derived synthesis gas into C{sub 1}-C{sub 4} alcohols by a highly selective process. Therefore, the variations of catalyst activity and selectivity for the synthesis of alcohols from H{sub 2}/CO {le}1 synthesis gas for a series of A/TX{sub 2} compounds, where A is a surface alkali dopant, T is a transition metal, and X ia a S, Se, or Te, will be determined. This quarter, a fresh batch of MoS{sub 2} was synthesized, and new Cs/MoS{sub 2} catalysts were prepared by alkali doping and were tested to demonstrate that the preparation and testing procedures were reproducible by different personnel. Preparations of RuS{sub 2} and Cs/RuS{sub 2} catalysts were initiated, and the preparations and testing of these catalysts will be described in the next quarterly report. 2 refs., 1 fig., 1 tab.

Thermal shock testing of TiC-coated molybdenum with pulsed hydrogen beams

International Nuclear Information System (INIS)

Nakamura, Kazuyuki

1985-07-01

Thermal shock testing of molybdenum samples, on which TiC is coated by TP-CVD and CVD methods, has been made by using a pulsed hydrogen beam. The power density applied was 2 kw/cm 2 . The test results showed that TiC coatings did not exfoliate until the melting of the substrate and showed good adhesion under the thermal shock condition. (author)

Exploring Effects of C2 Warfare on C2 Ability in a Simulated Environment

Science.gov (United States)

2011-06-01

Principal Axis Factoring, Oblimin rotation with Kaiser Normalization) included all prerequisites, but not the total value of C2 ability ( KMO = .84...Mission intent had the lowest value in this factor, a separate factor analysis was conducted on this factor ( KMO = .75; Bartlett’s test of

The microdose rapid 14C urea breath test compares well with the original rapid 14 breath test

International Nuclear Information System (INIS)

Bellon, M.S.; Bartholomeusz, F.D.L.; Chatterton, B.E.

2000-01-01

Full text: The 14 C urea breath test (CUBT) is a sensitive test used in the detection of H. pylori infection. The rapid 14 CUBT using 185 KBq of 14 C urea showed a sensitivity of 100% when tested in 36 patients. The aim of this study was to compare the results of the 14 CUBT performed following the ingestion of 37KBq microdose 14 C urea capsule (Bicapsule, Trimed) with the earlier method which uses 185 KBq 14 C urea. 19 patients (nine female age 21-52 yrs) were studied. All subjects first underwent a 14 CUBT with the microdose capsule and a single 15 minute post ingestion sample. An hour later the test was repeated but with a dose of 185 KBq 14 C urea in liquid form. A normal result was taken as 2 = 0.92). This is shown above. The Rapid 14 CUBT performed following the microdose capsule whilst reducing patient radiation exposure is an accurate test for the detection of H. pylori. Copyright (2000) The Australian and New Zealand Society of Nuclear Medicine Inc

Predicting outcome of paracetamol poisoning by using 14C-aminopyrine breath test

International Nuclear Information System (INIS)

Saunders, J.B.; Wright, N.; Lewis, K.O.

1980-01-01

The 14 C-aminopyrine ( 14 C-amidopyrine) breath test, carried out within 24 to 36 hours of an overdosage of paracetamol, was used to predict the extent of liver damage in 30 seriously poisoned patients. Mean 14 C0 2 excretion was 4.4% in 20 healthy control subjects; 5.5% in six patients who escaped injury; and 2.9%, 1.5%, and 0.2% in those with mild to moderate (12 patients), severe (eight patients), and fatal (four patients) liver damage respectively. This test proved to be a more reliable predictor of the extent of liver damage than plasma paracetamol concentration or half life or the results of conventional liver function tests and may enable treatment of hepatic failure to be started at an early stage. (author)

The HepTestContest: a global innovation contest to identify approaches to hepatitis B and C testing.

Science.gov (United States)

Tucker, Joseph D; Meyers, Kathrine; Best, John; Kaplan, Karyn; Pendse, Razia; Fenton, Kevin A; Andrieux-Meyer, Isabelle; Figueroa, Carmen; Goicochea, Pedro; Gore, Charles; Ishizaki, Azumi; Khwairakpam, Giten; Miller, Veronica; Mozalevskis, Antons; Ninburg, Michael; Ocama, Ponsiano; Peeling, Rosanna; Walsh, Nick; Colombo, Massimo G; Easterbrook, Philippa

2017-11-01

Innovation contests are a novel approach to elicit good ideas and innovative practices in various areas of public health. There remains limited published literature on approaches to deliver hepatitis testing. The purpose of this innovation contest was to identify examples of different hepatitis B and C approaches to support countries in their scale-up of hepatitis testing and to supplement development of formal recommendations on service delivery in the 2017 World Health Organization hepatitis B and C testing guidelines. This contest involved four steps: 1) establishment of a multisectoral steering committee to coordinate a call for contest entries; 2) dissemination of the call for entries through diverse media (Facebook, Twitter, YouTube, email listservs, academic journals); 3) independent ranking of submissions by a panel of judges according to pre-specified criteria (clarity of testing model, innovation, effectiveness, next steps) using a 1-10 scale; 4) recognition of highly ranked entries through presentation at international conferences, commendation certificate, and inclusion as a case study in the WHO 2017 testing guidelines. The innovation contest received 64 entries from 27 countries and took a total of 4 months to complete. Sixteen entries were directly included in the WHO testing guidelines. The entries covered testing in different populations, including primary care patients (n = 5), people who inject drugs (PWID) (n = 4), pregnant women (n = 4), general populations (n = 4), high-risk groups (n = 3), relatives of people living with hepatitis B and C (n = 2), migrants (n = 2), incarcerated individuals (n = 2), workers (n = 2), and emergency department patients (n = 2). A variety of different testing delivery approaches were employed, including integrated HIV-hepatitis testing (n = 12); integrated testing with harm reduction and addiction services (n = 9); use of electronic medical records to support targeted testing (n = 8

Comparison between the 13C-urea breath test and stool antigen test for the diagnosis of childhood Helicobacter pylori infection

International Nuclear Information System (INIS)

Kato, Seiichi; Minoura, Takanori; Iinuma, Kazuie; Konno, Mutsuko; Tajiri, Hitoshi; Matsuhisa, Takeshi

2004-01-01

As noninvasive tests for Helicobacter pylori infection, the 13 C-urea breath test (UBT) and stool antigen test have been widely used. In children, however, there are few studies reporting which test shows superior performance. The purpose of this study was to compare the 13 C-UBT and stool antigen test for their accuracy in diagnosing. H. pylori infection in children. A total of 123 Japanese children, ages 2 to 17 years (mean, 12 years) who underwent gastric biopsies for H. pylori infection were studied. The diagnoses included gastritis (n=55), gastric ulcer (n=5), duodenal ulcer (n=20), iron-deficiency anemia (n=7), and other conditions (n=36). The cutoff value of the 13 C-UBT was defined to be 3.5 per mille. The stool antigen test was performed using the H. pylori stool antigen (HpSA) enzyme-linked immunosorbent assay (ELISA) (Premier Platinum HpSA). In 16 patients who received eradication therapy, the 13 C-UBT and HpSA were repeated 2 months after treatment. Based on biopsy tests, 60 children were infected with H. pylori and 63 children were not. For the 13 C-UBT, the sensitivity, specificity, and accuracy were 95.0% (95% confidence interval [CI], 86.1%-99.0%), 98.4% (95% CI, 91.5%-100%), and 96.4% (95% CI, 93.6%-99.9%), respectively. For the HpSA, the sensitivity, specificity, and accuracy were 983.% (95% CI, 90.8%-100%), 98.4% (95% CI, 91.2%-100%), and 98.3% (95% CI, 96.0%-100%), respectively. There were no significant differences between the performance of these two tests. In the assessment of H. pylori eradication, the results of 13 C-UBT and HpSA agreed with those of biopsy tests. The 13 C-UBT and the HpSA are equally accurate for the diagnosis of active H. pylori infection in Japanese children. (author)

Blood Test: Hemoglobin A1C

Science.gov (United States)

... Why Are Hemoglobin A1c Tests Done? When a child has diabetes, hemoglobin A1c levels are followed to see how well medicines are working. If a child with diabetes has a high hemoglobin A1c level, it may ...

Assessment of full power turbine trip start-up test for C. Trillo 1 with RELAP5/MOD2

International Nuclear Information System (INIS)

Lozano, M.F.; Moreno, P.; de la Cal, C.; Larrea, E.; Lopez, A.; Santamaria, J.G.; Lopez, E.; Novo, M.

1993-07-01

C. Trillo I has developed a model of the plant with RELAP5/MOD2/36.04. This model will be validated against a selected set of start-up tests. One of the transients selected to that aim is the turbine trip, which presents very specific characteristics that make it significantly different from the same transient in other PWRs of different design, the main difference being that the reactor is not tripped: a reduction in primary power is carried out instead. Pre-test calculations were done of the Turbine Trip Test and compared against the actual test. Minor problems in the first model, specially in the Control and Limitation Systems, were identified and post-test calculations had been carried out. The results show a good agreement with data for all the compared variables

CHEK2 c.1100delC allele is rarely identified in Greek breast cancer cases.

Science.gov (United States)

Apostolou, Paraskevi; Fostira, Florentia; Papamentzelopoulou, Myrto; Michelli, Maria; Panopoulos, Christos; Fountzilas, George; Konstantopoulou, Irene; Voutsinas, Gerassimos E; Yannoukakos, Drakoulis

2015-04-01

The CHEK2 gene encodes a protein kinase that plays a crucial role in maintenance of genomic integrity and the DNA repair mechanism. CHEK2 germline mutations are associated with increased risk of breast cancer and other malignancies. From a clinical perspective, the most significant mutation identified is the c.1100delC mutation, which is associated with an approximately 25% lifetime breast cancer risk. The distribution of this mutation shows wide geographical variation; it is more prevalent in the Northern European countries and less common, or even absent, in Southern Europe. In order to estimate the frequency of the CHEK2 c.1100delC mutation in Greek breast cancer patients, we genotyped 2,449 patients (2,408 females and 41 males), which was the largest series ever tested for c.1100delC. The mean age of female and male breast cancer diagnosis was 49 and 59 years, respectively. All patients had previously tested negative for the Greek BRCA1 founder and recurrent mutations. The CHEK2 c.1100delC mutation was detected in 0.16% (4 of 2,408) of females, all of whom were diagnosed with breast cancer before the age of 50 years. Only one c.1100delC carrier was reported with breast cancer family history. The present study indicates that the CHEK2 c.1100delC mutation does not contribute substantially to hereditary breast cancer in patients of Greek descent. Copyright © 2015 Elsevier Inc. All rights reserved.

A testing facility for large scale models at 100 bar and 3000C to 10000C

International Nuclear Information System (INIS)

Zemann, H.

1978-07-01

A testing facility for large scale model tests is in construction under support of the Austrian Industry. It will contain a Prestressed Concrete Pressure Vessel (PCPV) with hot linear (300 0 C at 100 bar), an electrical heating system (1.2 MW, 1000 0 C), a gas supply system, and a cooling system for the testing space. The components themselves are models for advanced high temperature applications. The first main component which was tested successfully was the PCPV. Basic investigation of the building materials, improvements of concrete gauges, large scale model tests and measurements within the structural concrete and on the liner from the beginning of construction during the period of prestressing, the period of stabilization and the final pressurizing tests have been made. On the basis of these investigations a computer controlled safety surveillance system for long term high pressure, high temperature tests has been developed. (author)

22 CFR 34.18 - Waivers of indebtedness.

Science.gov (United States)

2010-04-01

... known through the exercise of due diligence that an error existed but failed to take corrective action... gain to the employee. (ii) [Reserved] (6) Under-withholding of life insurance premiums. 5 U.S.C. 8707(d... Federal Employees' Group Life Insurance Program premiums if the individual is without fault and recovery...

Phase C commissioning-Cernavoda Unit 2

International Nuclear Information System (INIS)

Munro, Robert

2007-01-01

Phase C commissioning program includes over 500 individual tests and checks which are carefully planned and scheduled at the correct power level. Some of the major tests are the following: - heat transport thermosyphoning test at 3% Full Power (FP); - dual computer failure test at 15% FP; - turbine overspeed test and generator first synchronization; - load rejection tests at 25, 50, 75 and 100% FP; - loss of Class IV Power test at 25% FP; - shutdown system (SDS nr. 1 and SDS nr. 2) tests at >60% FP; - condensate extraction and boiler feedwater pump trip tests at 100% FP; - power cycling through reactor setback from 100 to 10 and back to 100% FP; - condenser steam discharge valve tests with reactor at 100% FP and turbine at 60% output; - low pressure and high pressure heater box-up tests at 100% FP. Progress through the Phase C program is controlled at six specific Commissioning Control Points (CCPs) which meet the Romanian Regulatory Authority (CNCAN) and Management requirements. These CCPs are the following: PI - Approval for Power increase to 5% FP; PP1 - Approval for Power increase to 25% FP; PP2 - Approval for Power increase to 50% FP; PP3 - Approval for Power increase to 75% FP; PP4 - Approval for Power increase to 100% FP. Prior to releasing each of these CCPs both Management and CNCAN complete an assessment of the 'Readiness' to proceed to the next power plateau. The readiness includes a review of the plant material condition, results of previous tests, documentation status, and operability maintainability issues. (author)

Development of TiC and TiN coated molybdenum limiter system and initial results of the thermal testing in neutral beam heated JFT-2 tokamak

International Nuclear Information System (INIS)

Nakamura, Hiroo; Sengoku, Seio; Maeno, Masaki; Yamamoto, Shin; Seki, Masahiro; Kazawa, Minoru

1982-06-01

This paper describes the limiter drive system for TiC and TiN coated molybdenum limiters and the thermal testing results of the TiC coated limiter in the JFT-2 tokamak using neutral beam injection (0.7 MW). To investigate the influence of TiC coated limiter on plasma behavior and adhesion property under tokamak plasma, a full scale limiter test has been performed in the JFT-2. Reproducible plasma was obtained after the plasma conditioning. Maximum heat flux to the limiter, measured by IR camera, was 1.5 -- 6.5 kW/cm 2 in 25 msec. Cracking, exfoliation and melting on TiC coated limiter were not observed, except for a number of arc tracks. Finally, the permissible heat fluxes of TiC coated molybdenum first wall are discussed. (author)

CANFLEX fuel bundle cross-flow endurance test 2 (test procedure)

Energy Technology Data Exchange (ETDEWEB)

Hong, Sung Deok; Chung, C. H.; Chang, S. K. [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-04-01

This report describes test procedure of cross-flow 2 test for CANFLEX fuel. In October 1996. a cross-flow test was successfully performed in the KAERI Hot Test Loop for four hours at a water flow rate of 31kg/s, temperature of 266 deg C and inlet pressure of 11MPa, but it is requested more extended time periods to determine a realistic operational margin for the CANFLEX bundle during abnormal refuelling operations. The test shall be conducted for twenty two hours under the reactor conditions. After an initial period of ten hours, the test shall be stopped at the intervals of four hours for bundle inspection and inspect the test bundle end-plate to end-cap welds for failure or crack propagation using liquid penetrant examination. 2 refs., 1 fig. (Author)

The HepTestContest: a global innovation contest to identify approaches to hepatitis B and C testing

Directory of Open Access Journals (Sweden)

Joseph D. Tucker

2017-11-01

Full Text Available Abstract Background Innovation contests are a novel approach to elicit good ideas and innovative practices in various areas of public health. There remains limited published literature on approaches to deliver hepatitis testing. The purpose of this innovation contest was to identify examples of different hepatitis B and C approaches to support countries in their scale-up of hepatitis testing and to supplement development of formal recommendations on service delivery in the 2017 World Health Organization hepatitis B and C testing guidelines. Methods This contest involved four steps: 1 establishment of a multisectoral steering committee to coordinate a call for contest entries; 2 dissemination of the call for entries through diverse media (Facebook, Twitter, YouTube, email listservs, academic journals; 3 independent ranking of submissions by a panel of judges according to pre-specified criteria (clarity of testing model, innovation, effectiveness, next steps using a 1-10 scale; 4 recognition of highly ranked entries through presentation at international conferences, commendation certificate, and inclusion as a case study in the WHO 2017 testing guidelines. Results The innovation contest received 64 entries from 27 countries and took a total of 4 months to complete. Sixteen entries were directly included in the WHO testing guidelines. The entries covered testing in different populations, including primary care patients (n = 5, people who inject drugs (PWID (n = 4, pregnant women (n = 4, general populations (n = 4, high-risk groups (n = 3, relatives of people living with hepatitis B and C (n = 2, migrants (n = 2, incarcerated individuals (n = 2, workers (n = 2, and emergency department patients (n = 2. A variety of different testing delivery approaches were employed, including integrated HIV-hepatitis testing (n = 12; integrated testing with harm reduction and addiction services (n = 9; use of electronic medical records to

Home urine C-peptide creatinine ratio (UCPCR) testing can identify type 2 and MODY in pediatric diabetes.

Science.gov (United States)

Besser, Rachel E J; Shields, Beverley M; Hammersley, Suzanne E; Colclough, Kevin; McDonald, Timothy J; Gray, Zoe; Heywood, James J N; Barrett, Timothy G; Hattersley, Andrew T

2013-05-01

Making the correct diabetes diagnosis in children is crucial for lifelong management. Type 2 diabetes and maturity onset diabetes of the young (MODY) are seen in the pediatric setting, and can be difficult to discriminate from type 1 diabetes. Postprandial urinary C-peptide creatinine ratio (UCPCR) is a non-invasive measure of endogenous insulin secretion that has not been tested as a diagnostic tool in children or in patients with diabetes duration MODY and type 2 in pediatric diabetes. Two-hour postprandial UCPCR was measured in 264 patients aged MODY, n = 63). Receiver operating characteristic curves were used to identify the optimal UCPCR cutoff for discriminating diabetes subtypes. UCPCR was lower in type 1 diabetes [0.05 (MODY [3.51 (2.37-5.32) nmol/mmol, p MODY (p = 0.25), so patients were combined for subsequent analyses. After 2-yr duration, UCPCR ≥ 0.7 nmol/mmol has 100% sensitivity [95% confidence interval (CI): 92-100] and 97% specificity (95% CI: 91-99) for identifying non-type 1 (MODY + type 2 diabetes) from type 1 diabetes [area under the curve (AUC) 0.997]. UCPCR was poor at discriminating MODY from type 2 diabetes (AUC 0.57). UCPCR testing can be used in diabetes duration greater than 2 yr to identify pediatric patients with non-type 1 diabetes. UCPCR testing is a practical non-invasive method for use in the pediatric outpatient setting. © 2013 John Wiley & Sons A/S.

NCBI nr-aa BLAST: CBRC-CJAC-01-1460 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-CJAC-01-1460 ref|ZP_01461283.1| hypothetical protein STIAU_3418 [Stigmatella a...urantiaca DW4/3-1] gb|EAU67945.1| hypothetical protein STIAU_3418 [Stigmatella aurantiaca DW4/3-1] ZP_01461283.1 0.039 27% ...

Patterns of type 2 diabetes monitoring in rural towns: How does frequency of HbA1c and lipid testing compare with existing guidelines?

Science.gov (United States)

Paul, Christine L; Piterman, Leon; Shaw, Jonathan E; Kirby, Catherine; Barker, Daniel; Robinson, Jennifer; Forshaw, Kristy L; Sikaris, Kenneth A; Bisquera, Alessandra; Sanson-Fisher, Robert W

2016-12-01

To indicate levels of monitoring of type 2 diabetes in rural and regional Australia by examining patterns of glycated haemoglobin (HbA1c) and blood lipid testing. Retrospective analysis of pathology services data from twenty regional and rural towns in eastern Australia over 24 months. Of 13 105 individuals who had either a single HbA1c result ≥7.0% (53 mmol mol -1 ); or two or more HbA1c tests within the study period. Frequency of testing of HbA1c and blood lipids (cholesterol, low-density lipoprotein (LDL) cholesterol, high-density lipoprotein (HDL) cholesterol and triglycerides) were compared with guideline recommendations. About 58.3% of patients did not have the recommended 6-monthly HbA1c tests and 30.6% did not have annual lipid testing. For those who did not receive tests at the recommended interval, the mean between-test interval was 10.5 months (95% CI = 7.5-13.5) rather than 6 months for HbA1c testing; and 15.7 (95% CI = 13.3-18.1) months rather than annually for blood lipids. For those with at least one out-of-range test result, 77% of patients failed to receive a follow-up HbA1c test and 86.5% failed to receive a follow-up blood lipid test within the recommended 3 months. Patients less than 50 years of age, living in a more remote area and with poor diabetes control were less likely to have testing at the recommended intervals (P < 0.0001). Although poor diabetes testing is not limited to rural areas, more intensive diabetes monitoring is likely to be needed for patients living in non-metropolitan areas, particularly for some subgroups. © 2016 National Rural Health Alliance Inc.

Test plan for tank 241-C-104 retrieval testing

International Nuclear Information System (INIS)

HERTING, D.L.

1999-01-01

Tank 241-C-104 has been identified as one of the first tanks to be retrieved for high-level waste pretreatment and immobilization. Retrieval of the tank waste will require dilution. Laboratory tests are needed to determine the amount of dilution required for safe retrieval and transfer of feed. The proposed laboratory tests are described in this document

Test Plan for Tank 241-C-104 Retrieval Testing

International Nuclear Information System (INIS)

HERTING, D.L.

1999-01-01

Tank 241-C-104 has been identified as one of the first tanks to be retrieved for high-level waste pretreatment and immobilization. Retrieval of the tank waste will require dilution. Laboratory tests are needed to determine the amount of dilution required for safe retrieval and transfer of feed. The proposed laboratory tests are described in this document

Voltage-sensing phosphatase modulation by a C2 domain.

Science.gov (United States)

Castle, Paul M; Zolman, Kevin D; Kohout, Susy C

2015-01-01

The voltage-sensing phosphatase (VSP) is the first example of an enzyme controlled by changes in membrane potential. VSP has four distinct regions: the transmembrane voltage-sensing domain (VSD), the inter-domain linker, the cytosolic catalytic domain, and the C2 domain. The VSD transmits the changes in membrane potential through the inter-domain linker activating the catalytic domain which then dephosphorylates phosphatidylinositol phosphate (PIP) lipids. The role of the C2, however, has not been established. In this study, we explore two possible roles for the C2: catalysis and membrane-binding. The Ci-VSP crystal structures show that the C2 residue Y522 lines the active site suggesting a contribution to catalysis. When we mutated Y522 to phenylalanine, we found a shift in the voltage dependence of activity. This suggests hydrogen bonding as a mechanism of action. Going one step further, when we deleted the entire C2 domain, we found voltage-dependent enzyme activity was no longer detectable. This result clearly indicates the entire C2 is necessary for catalysis as well as for modulating activity. As C2s are known membrane-binding domains, we tested whether the VSP C2 interacts with the membrane. We probed a cluster of four positively charged residues lining the top of the C2 and suggested by previous studies to interact with phosphatidylinositol 4,5-bisphosphate [PI(4,5)P2] (Kalli et al., 2014). Neutralizing those positive charges significantly shifted the voltage dependence of activity to higher voltages. We tested membrane binding by depleting PI(4,5)P2 from the membrane using the 5HT2C receptor and found that the VSD motions as measured by voltage clamp fluorometry (VCF) were not changed. These results suggest that if the C2 domain interacts with the membrane to influence VSP function it may not occur exclusively through PI(4,5)P2. Together, this data advances our understanding of the VSP C2 by demonstrating a necessary and critical role for the C2 domain in

Volume properties and refraction of aqueous solutions of bisadducts of light fullerene C60 and essential amino acids lysine, threonine, and oxyproline (C60(C6H13N2O2)2, C60(C4H8NO3)2, and C60(C5H9NO2)2) at 25°C

Science.gov (United States)

Semenov, K. N.; Ivanova, N. M.; Charykov, N. A.; Keskinov, V. A.; Kalacheva, S. S.; Duryagina, N. N.; Garamova, P. V.; Kulenova, N. A.; Nabieva, A.

2017-02-01

Concentration dependences of the density of aqueous solutions of bisadducts of light fullerene C60 and essential amino acids are studied by pycnometry. Concentration dependences of the average molar volumes and partial volumes of components (H2O and corresponding bisadducts) are calculated for C60(C6H13N2O2)2-H2O, C60(C4H8NO3)2-H2O, and C60(C5H9NO2)2-H2O binary systems at 25°C. Concentration dependences of the indices of refraction of C60(C6H13N2O2)2-H2O, C60(C4H8NO3)2-H2O, and C60(C5H9NO2)2-H2O binary systems are determined at 25°C. The concentration dependences of specific refraction and molar refraction of bisadducts and aqueous solutions of them are calculated.

Surveillance test of OWL-2 inpile tube

International Nuclear Information System (INIS)

Shimizu, Masatsugu; Itoh, Noboru

1976-08-01

A series of irradiation surveillance tests performed in integrity evaluation of an inpile tube for the test loop OWL-2 are described. Specimens were exposed to the neutron fluences from 1 x 10 20 to 3.4 x 10 21 n/cm 2 (>1 MeV), and subjected to post-irradiation tensile test at room temperature and service temperature 285 0 C. The strength increased and the ductility decreased with increasing neutron fluence. The reduction in fracture ductility due to neutron irradiation in the fluence range was insignificant, and the elongation of 33% was retained even for the maximum neutron fluence at 285 0 C. Little decrease of the ductility with fluence indicates that the tube would be in service for long time, ie to the integral fluence of 3.4 x 10 21 n/cm 2 . (auth.)

C-106 tank process ventilation test

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

Project W-320 Acceptance Test Report for tank 241-C-106, 296-C-006 Ventilation System Acceptance Test Procedure (ATP) HNF-SD-W320-012, C-106 Tank Process Ventilation Test, was an in depth test of the 296-C-006 ventilation system and ventilation support systems required to perform the sluicing of tank C-106. Systems involved included electrical, instrumentation, chiller and HVAC. Tests began at component level, moved to loop level, up to system level and finally to an integrated systems level test. One criteria was to perform the test with the least amount of risk from a radioactive contamination potential stand point. To accomplish this a temporary configuration was designed that would simulate operation of the systems, without being connected directly to the waste tank air space. This was done by blanking off ducting to the tank and connecting temporary ducting and an inlet air filter and housing to the recirculation system. This configuration would eventually become the possible cause of exceptions. During the performance of the test, there were points where the equipment did not function per the directions listed in the ATP. These events fell into several different categories. The first and easiest problems were field configurations that did not match the design documentation. This was corrected by modifying the field configuration to meet design documentation and reperforming the applicable sections of the ATP. A second type of problem encountered was associated with equipment which did not operate correctly, at which point an exception was written against the ATP, to be resolved later. A third type of problem was with equipment that actually operated correctly but the directions in the ATP were in error. These were corrected by generating an Engineering Change Notice (ECN) against the ATP. The ATP with corrected directions was then re-performed. A fourth type of problem was where the directions in the ATP were as the equipment should operate, but the design of

[Relationship between dietary vitamin C and Type 2 diabetes].

Science.gov (United States)

Li, Xiaoxiao; Wang, Xinliang; Wei, Jie; Yang, Tubao

2015-10-01

To examine the correlation between dietary vitamin C intake and Type 2 diabetes.
 A total of 5 168 participants from Xiangya Hospital, Central South University were randomly selected. According to the vitamin C intake, the participants were divided into 5 groups: a Q1 group (n=1 033), a Q2 group (n=1 034), a Q3 group (n=1 034), a Q4 group (n=1 034) and a Q5 group (n=1 033). They were also divided into a Type 2 diabetes group (n=502) and a non-diabetes group (n=4 666). The height, weight, and blood pressure were measured, and vitamin C intake and other dairy consumption were evaluated using a food frequency questionnaire and fasting plasma glucose (FPG). The analysis of variance (ANOVA), Chi-square test, Mann-Whitney U test and logistic regression model were used to analyze the relationship between dietary vitamin C and Type 2 diabetes.
 The univariate analysis showed that there were significant differences in the vitamin C consumption in energy intake, activity level, dietary fiber intake, nutritional supplementation status, drinking or not drinking, education level among the different vitamin C intake groups (all Pvitamin C intake between the Type 2 diabetes group and the non-diabetes group (all Pvitamin C intake (>154.78 mg/d) in comparison with the lowest level (≤ 63.26 mg/d). The results suggested that the vitamin C intake was inversely associated with the Type 2 diabetes (r=-0.029, Pvitamin C intake and the risk of Type 2 diabetes.

Hot Corrosion Behavior of Bare, Cr3C2-(NiCr) and Cr3C2-(NiCr) + 0.2wt.%Zr Coated SuperNi 718 at 900 °C

Science.gov (United States)

Mudgal, Deepa; Singh, Surendra; Prakash, Satya

2015-01-01

Corrosion in incinerators, power plants, and chemical industries are frequently encountered due to the presence of salts containing sodium, sulphur, and chlorine. To obviate this problem, bare and coated alloys were tested under environments simulating the conditions present inside incinerators and power plants. 0.2 wt.% zirconium powder was incorporated in the Cr3C2-(NiCr) coating powder. The original powder and Zr containing powder was sprayed on Superni 718 alloy by D-gun technique. The bare and coated alloys were tested under Na2SO4 + K2SO4 + NaCl + KCl and Na2SO4 + NaCl environment. The corrosion rate of specimens was monitored using weight change measurements. Characterization of the corrosion products has been done using FE-SEM/EDS and XRD techniques. Bare and coated alloys showed very good corrosion resistance under given molten salt environments. Addition of 0.2wt.%Zr in Cr3C2-25%(NiCr) coating further greatly reduced the oxidation rate as well as improved the adherence of oxide scale to the coating surface during the time of corrosion.

Oxidation of UO2 at 150 to 3500C

International Nuclear Information System (INIS)

White, G.D.; Knox, C.A.; Gilbert, E.R.; Johnson, A.B. Jr.

1983-07-01

Oxidation of UO 2 through breached LWR spent fuel rods during interim storage in air atmospheres is a potential mechanism for degradation of cladding integrity. The temperature-time range of published data are inadequate to establish long term behavior under dry storage conditions. Consequently, tests are being conducted in the temperature range of 150 to 350 0 C on unirradiated pellets to evaluate fuel oxidation behavior. The tests have revealed significant-to-minor oxidation at temperatures down to 200 0 C and no measurable oxidation at 150 0 C for times up to 3000 hours. Oxidation at 200 0 C for 2000 hours led to formation of low density particulate U 3 O 8 which destroys pellet integrity. Oxidation of UO 2 pellets at 215 and 250 0 C was signifcantly accelerated by the presence of 1 volume percent NO 2 in the air. NO 2 is a potential constituent of the air, forming by radiolysis in the gamma radiation field associated with spent fuel assemblies. NO 2 reaction with UO 2 pellets leads to accelerated formation of UO 3 and pellet disintegration. 11 references, 15 figures

Atmospheric chemistry of C2F5CHO: mechanism of the C2F5C(O)O-2+HO2 reaction

DEFF Research Database (Denmark)

Andersen, Mads Peter Sulbæk; Hurley, MD; Wallington, TJ

2003-01-01

in a yield of 76 +/- 4 The gas phase reaction of CnF2n+1C(O)O-2 with HO2 radicals offers a potential explanation for at least part of the observed environmental burden of fluorinated carboxylic acids, CnF2n+1C(O)OH. As part of this work an upper limit for the rate constant of reaction of Cl atorns with C2F5C......(O)OH at 296 K was determined; k(Cl + C2F5C(O)OH) 1 x 10(-11) cm(3) molecule(-1) s(-1). (C) 2003 Published by Elsevier B.V....

Assessment of the (/sup 14/C) aminopyrine breath test in liver disease

Energy Technology Data Exchange (ETDEWEB)

Galizzi, J; Long, R G; Billing, B H; Sherlock, S [Royal Free Hospital, London (UK)

1978-01-01

Different methods of performing the (/sup 14/C) aminopyrine breath test have been assessed. A tracer dose of 2 ..mu..Ci without a loading dose and with a single breath collection at two hours was the method selected, since it gave the best discrimination between patients with hepatocellular diseases and normal subjects (5.2 +- 0.2%, mean - SEM). Reduced values occurred in patients with chronic active hepatitis (with and without cirrhosis) (1.5 +- 0.2%), alcoholic cirrhosis (1.7 +- 0.4%) and hepatitis (2.5 +- 0.3%), and late primary biliary cirrhosis suggesting defective microsomal function with respect to demethylation. Normal results were common in early primary biliary cirrhosis. Two weeks of prednisolone therapy caused some improvement in the breath test in nine of ten patients with chronic active hepatitis. It is concluded that the (/sup 14/C) aminopyrine breath test is a simple test for detecting hepatocellular dysfunction, but has no obvious diagnostic advantage over the determination of serum aspartate transaminase and two hour post-prandial bile-acids.

Results and interpretation of preliminary aquifer tests in boreholes UE-25c number-sign 1, UE-25c number-sign 2, and UE-25c number-sign 3, Yucca Mountain, Nye County, Nevada

International Nuclear Information System (INIS)

Geldon, A.L.

1996-01-01

Pumping and injection tests conducted in 1983 and 1984 in boreholes UE-25c number-sign 1, UE-25c number-sign 2, and UE-25c number-sign 3 (the c-holes) at Yucca Mountain, Nevada, were analyzed with respect to information obtained from lithologic and borehole geophysical logs, core permeameter tests, and borehole flow surveys. The three closely spaced c-holes, each of which is about 3,000 feet deep, are completed mainly in nonwelded to densely welded, ash-flow tuff of the tuffs and lavas of Calico Hills and the Crater Flat Tuff of Miocene age. Below the water table, tectonic and cooling fractures pervade the tuffaceous rocks but are distributed mainly in 11 transmissive intervals, many of which also have matrix permeability. Information contained in this report is presented as part of ongoing investigations by the US Geological Survey (USGS) regarding the hydrologic and geologic suitability of Yucca Mountain, Nevada, as a potential site for the storage of high-level nuclear waste in an underground mined geologic repository. This investigation was conducted in cooperation with the US Department of Energy under Interagency Agreement DE-AI08-78ET44802, as part of the Yucca Mountain Site Characterization Project

Strain-dependent effects of diazepam and the 5-HT2B/2C receptor antagonist SB 206553 in spontaneously hypertensive and Lewis rats tested in the elevated plus-maze

Directory of Open Access Journals (Sweden)

Takahashi R.N.

2001-01-01

Full Text Available The 5-HT2B/2C receptor antagonist SB 206553 exerts anxiolytic effects in rat models of anxiety. However, these effects have been reported for standard rat strains, thus raising the issue of SB 206553 effects in rat strains displaying different levels of anxiety. Herein, the effects of SB 206553 in a 5-min elevated plus-maze test of anxiety were compared to those of the reference anxiolytic, diazepam, in two rat strains respectively displaying high (Lewis rats and low (spontaneously hypertensive rats, SHR anxiety. Diazepam (0.37, 0.75, or 1.5 mg/kg; 30 min before testing increased in a dose-dependent manner the behavioral measures in SHR, but not in Lewis rats. On the other hand, SB 206553 (1.25, 2.5, or 5 mg/kg; 30 min before testing failed to alter the anxiety parameters in both strains, whereas it increased closed arm entries in Lewis rats, suggesting that it elicited hyperactivity in the latter strain. Accordingly, the hypolocomotor effect of the nonselective 5-HT2B/2C receptor agonist m-chlorophenylpiperazine (1.5 mg/kg ip 20 min before a 15-min exposure to an activity cage was prevented by the 1.25 and 2.5 mg/kg doses of SB 206553 in Lewis rats and SHR, respectively. Compared with SHR, Lewis rats may display a lower response to benzodiazepine-mediated effects and a more efficient control of locomotor activity by 5-HT2B/2C receptors.

Alkali/TX[sub 2] catalysts for CO/H[sub 2] conversion to C[sub 1]-C[sub 4] alcohols

Energy Technology Data Exchange (ETDEWEB)

Klier, K.; Herman, R.G.; Bastian, R.D.; Flanagan, K.L.

1989-01-01

Ruthenium disulfide catalysts have been synthesized, tested, and characterized during this period of research. It was observed that both the undoped and Cs-doped RuS[sub 2] catalysts produced alcohols and lower amounts of hydrocarbons from H[sub 2]/CO = 1.0 synthesis gas at temperatures above 300[degree]C. Calcination and catalytic testing resulted in partial reduction of the RuS[sub 2] to Ru[sup o]. Calcination under H[sub 2]S prevented the partial reduction of the RuS[sub 2] catalyst, but subsequent catalytic testing again resulted in the formation of a quantity of Ru[sup o]. A Cs-doped RuS[sub 2] catalyst was prepared, but it might have had too high of a loading of Cs. Upon testing, a lower activity was observed for the doped catalyst compared with the undoped catalyst, but the alcohol selectivity was the same for the two catalysts.

Generic test platform for representative tests of safety I/C systems - 15546

International Nuclear Information System (INIS)

Fourestie, B.; Kuck, H.; Richter, J.; Rieche, S.; Waitz, M.

2015-01-01

In compliance with the IEC 61513 safety Instrumentation and Control (I/C) systems must be successfully validated in their final configuration prior to installation on site and commissioning. However the contingent need for modifications during system validation activities or subsequently during the commissioning phase may entail long and costly re-engineering of the I/C systems. With the view to ease these possible modifications, a Generic Test Platform has been developed by AREVA which allows combining a real I/C system subpart with an emulation server. This platform provides a faithful representation of the I/C System allowing crediting the validation test results carried out on this platform. (authors)

Tests sérologiques dans la maladie cœliaque

Science.gov (United States)

Rashid, Mohsin; Lee, Jennie

2016-01-01

Résumé Objectif Répondre aux questions souvent posées par les généralistes et aux difficultés auxquelles ils font face lorsqu’ils prescrivent des tests sérologiques pour la maladie cœliaque et fournir des conseils pratiques pour aider à interpréter les résultats des tests. Sources de l’information Une recherche a été effectuée dans MEDLINE pour les lignes directrices sur le diagnostic et la prise en charge de la maladie cœliaque publiées en anglais entre 2000 et 2015 par des organisations professionnelles de gastro-entérologie. Message principal Pour dépister la maladie cœliaque, le dosage de l’anticorps immunoglobuline A (IgA) anti-transglutaminase tissulaire est le test de choix. Il faut mesurer le taux sérique d’IgA totale afin d’écarter un déficit sélectif en IgA et d’éviter les faux négatifs. Les patients dont le test sérologique est positif doivent être recommandés à un gastro-entérologue pour subir des biopsies de l’intestin grêle par endoscopie afin de confirmer le diagnostic. Le typage des antigènes des leucocytes humains DQ2 et DQ8 peut aider à écarter le diagnostic. Un régime sans gluten ne doit pas être entrepris avant que le diagnostic de maladie cœliaque soit confirmé. Conclusion Les tests sérologiques sont très utiles pour confirmer les soupçons d’une maladie cœliaque. Le diagnostic précoce est essentiel pour prévenir les complications liées à la maladie cœliaque.

Voltage-sensing phosphatase modulation by a C2 domain

Directory of Open Access Journals (Sweden)

Paul M. Castle

2015-04-01

Full Text Available The voltage-sensing phosphatase (VSP is the first example of an enzyme controlled by changes in membrane potential. VSP has four distinct regions: the transmembrane voltage-sensing domain (VSD, the inter-domain linker, the cytosolic catalytic domain and the C2 domain. The VSD transmits the changes in membrane potential through the inter-domain linker activating the catalytic domain which then dephosphorylates phosphatidylinositol phosphate lipids. The role of the C2, however, has not been established. In this study, we explore two possible roles for the C2: catalysis and membrane-binding. The Ci-VSP crystal structures show that the C2 residue Y522 lines the active site suggesting a contribution to catalysis. When we mutated Y522 to phenylalanine, we found a shift in the voltage dependence of activity. This suggests hydrogen bonding as a mechanism of action. Going one step further, when we deleted the entire C2 domain, we found voltage-dependent enzyme activity was no longer detectable. This result clearly indicates the entire C2 is necessary for catalysis as well as for modulating activity. As C2s are known membrane-binding domains, we tested whether the VSP C2 interacts with the membrane. We probed a cluster of four positively charged residues lining the top of the C2 and suggested by previous studies to interact with phosphatidylinositol 4,5-bisphosphate (PI(4,5P2 (Kalli et al., 2014. Neutralizing those positive charges significantly shifted the voltage dependence of activity to higher voltages. We tested membrane binding by depleting PI(4,5P2 from the membrane using the 5HT2C receptor and found that the VSD motions as measured by voltage clamp fluorometry were not changed. These results suggest that if the C2 domain interacts with the membrane to influence VSP function it may not occur exclusively through PI(4,5P2. Together, this data advances our understanding of the VSP C2 by demonstrating a necessary and critical role for the C2 domain in

AGR-2 Irradiation Test Final As-Run Report, Rev 2

Energy Technology Data Exchange (ETDEWEB)

Collin, Blaise P. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2014-08-01

This document presents the as-run analysis of the AGR-2 irradiation experiment. AGR-2 is the second of the planned irradiations for the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. Funding for this program is provided by the U.S. Department of Energy as part of the Very High Temperature Reactor (VHTR) Technical Development Office (TDO) program. The objectives of the AGR-2 experiment are to: (a) Irradiate UCO (uranium oxycarbide) and UO₂ (uranium dioxide) fuel produced in a large coater. Fuel attributes are based on results obtained from the AGR-1 test and other project activities. (b) Provide irradiated fuel samples for post-irradiation experiment (PIE) and safety testing. (c) Support the development of an understanding of the relationship between fuel fabrication processes, fuel product properties, and irradiation performance. The primary objective of the test was to irradiate both UCO and UO₂ TRISO (tri-structural isotropic) fuel produced from prototypic scale equipment to obtain normal operation and accident condition fuel performance data. The UCO compacts were subjected to a range of burnups and temperatures typical of anticipated prismatic reactor service conditions in three capsules. The test train also includes compacts containing UO₂ particles produced independently by the United States, South Africa, and France in three separate capsules. The range of burnups and temperatures in these capsules were typical of anticipated pebble bed reactor service conditions. The results discussed in this report pertain only to U.S. produced fuel. In order to achieve the test objectives, the AGR-2 experiment was irradiated in the B-12 position of the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) for a total irradiation duration of 559.2 effective full power days (EFPD). Irradiation began on June 22, 2010, and ended on October 16, 2013, spanning 12 ATR power cycles and approximately three and a

Fourier spectroscopy of the 12C2, 13C2, and 12C13C (0-0) swan bands

International Nuclear Information System (INIS)

Amiot, C.

1983-01-01

The (0-0) band of the C 2 Swan electronic system d 3 Pi/sub g/→a 3 Pi/sub u/ has been recorded by Fourier spectroscopy. The three isotopes species 12 C 2 , 13 C 2 , and 12 C 13 C were investigated. The observed wavenumbers were reduced to molecular parameters using a nonlinear least-square fitting procedure. Well-known perturbations at N' = 47 and N' = 51 again observed in the e 12 C 2 d 3 Pi/sub g/ (v = 0) level. Perturbations of the same kind are present in the 13 C 2 spectrum at N' = 34 and N' = 44,48,52. The 12 C 13 C spectrum exhibits in the observed spectral range a unique perturbation for N' = 41

High performance Li{sub 3}V{sub 2}(PO{sub 4}){sub 3}/C composite cathode material for lithium ion batteries studied in pilot scale test

Energy Technology Data Exchange (ETDEWEB)

Chen Zhenyu [School of Chemical Engineering and Technology, Harbin Institute of Technology, Harbin 150001 (China); Dai Changsong, E-mail: changsd@hit.edu.c [School of Chemical Engineering and Technology, Harbin Institute of Technology, Harbin 150001 (China); Wu Gang; Nelson, Mark [Materials Physics and Applications Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Hu Xinguo [School of Chemical Engineering and Technology, Harbin Institute of Technology, Harbin 150001 (China); Zhang Ruoxin; Liu Jiansheng; Xia Jicai [Battery Material Business Division, Guangzhou Tinci Materials Technology Co., Ltd., Guangzhou 510760 (China)

2010-12-01

Li{sub 3}V{sub 2}(PO{sub 4}){sub 3}/C composite cathode material was synthesized via carbothermal reduction process in a pilot scale production test using battery grade raw materials with the aim of studying the feasibility for their practical applications. XRD, FT-IR, XPS, CV, EIS and battery charge-discharge tests were used to characterize the as-prepared material. The XRD and FT-IR data suggested that the as-prepared Li{sub 3}V{sub 2}(PO{sub 4}){sub 3}/C material exhibits an orderly monoclinic structure based on the connectivity of PO{sub 4} tetrahedra and VO{sub 6} octahedra. Half cell tests indicated that an excellent high-rate cyclic performance was achieved on the Li{sub 3}V{sub 2}(PO{sub 4}){sub 3}/C cathodes in the voltage range of 3.0-4.3 V, retaining a capacity of 95% (96 mAh/g) after 100 cycles at 20C discharge rate. The low-temperature performance of the cathode was further evaluated, showing 0.5C discharge capacity of 122 and 119 mAh/g at -25 and -40 {sup o}C, respectively. The discharge capacity of graphite//Li{sub 3}V{sub 2}(PO{sub 4}){sub 3} batteries with a designed battery capacity of 14 Ah is as high as 109 mAh/g with a capacity retention of 92% after 224 cycles at 2C discharge rates. The promising high-rate and low-temperature performance observed in this work suggests that Li{sub 3}V{sub 2}(PO{sub 4}){sub 3}/C is a very strong candidate to be a cathode in a next-generation Li-ion battery for electric vehicle applications.

13C-urea breath test analyzed with infrared isotope spectrometry for the diagnosis of Helicobacter pylori

International Nuclear Information System (INIS)

Dahlberg, M.; Schoensby, H.

1998-01-01

The authors have evaluated a 13 C-urea breath test for the diagnosis of Helicobacter pylori infection. The 13 C-test was analyzed with isotope-selective non-dispersive infrared spectrometry and compared with a 14 C-urea breath test and the urease test in gastric mucosal biopsies. 46 patients were analyzed with breath tests, 23 patients were negative and 22 patients were positive with both methods. One patients was positive with 14 C-method and negative with the 13 C-urea breath test. 61 patients were analyzed with the 13 C-urea breath test and the urease test. 30 patients were negative and 30 patients were positive with both methods, whereas one patient with a negative urease test had a positive breath test. 13 C-urea breath test analyzed with isotope-selective non-dispersive infrared spectrometry is a fast, simple, non-radioactive, non-invasive, convenient and reliable method for the diagnosis of Helicobacter pylori infection. 12 refs., 2 figs., 1 tab

Assessment of TRAC-PD2 reflood core thermo-hydraulic model by CCTF Test C1-16

International Nuclear Information System (INIS)

Sugimoto, Jun

1982-11-01

The TRAC-PD2 reflood core thermo-hydraulic model was assessed by CCTF Test C1-16. The measured data were utilized as core boundary conditions in the TRAC calculations. The results indicate that the core inlet liquid temperature and the core heater rod temperatures are in reasonable agreement with data, but the pressure distribution in the core and water pool formation in the upper plenum are not in good agreement. The parametric effects of the droplet critical Weber number, the material properties of the heater rod, the noding of the upper plenum, and the minimum stable film boiling temperature are also discussed. (author)

Thermal shock properties of 2D-SiCf/SiC composites

International Nuclear Information System (INIS)

Lee, Sang Pill; Lee, Jin Kyung; Son, In Soo; Bae, Dong Su; Kohyama, Akira

2012-01-01

This paper dealt with the thermal shock properties of SiC f /SiC composites reinforced with two dimensional SiC fabrics. SiC f /SiC composites were fabricated by a liquid phase sintering process, using a commercial nano-size SiC powder and oxide additive materials. An Al 2 O 3 –Y 2 O 3 –SiO 2 powder mixture was used as a sintering additive for the consolidation of SiC matrix region. In this composite system, Tyranno SA SiC fabrics were also utilized as a reinforcing material. The thermal shock test for SiC f /SiC composites was carried out at the elevated temperature. Both mechanical strength and microstructure of SiC f /SiC composites were investigated by means of optical microscopy, SEM and three point bending test. SiC f /SiC composites represented a dense morphology with a porosity of about 8.2% and a flexural strength of about 160 MPs. The characterization of SiC f /SiC composites was greatly affected by the history of cyclic thermal shock. Especially, SiC f /SiC composites represented a reduction of flexural strength at the thermal shock temperature difference higher than 800 °C.

Proceedings of the Third NRC/ASME Symposium on Valve and Pump Testing. Session 1A--Session 2C: Volume 1

International Nuclear Information System (INIS)

1994-07-01

The 1994 Symposium on Valve and Pump Testing, jointly sponsored by the Board of Nuclear Codes and Standards of the American Society of Mechanical Engineers and by the Nuclear Regulatory Commission, provides a forum for the discussion of current programs and methods for inservice testing and motor-operated valve testing at nuclear power plants. The symposium also provides an opportunity to discuss the need to improve that testing in order to help ensure the reliable performance of pumps and valves. The participation of industry representatives, regulators, and consultants results in the discussion of a broad spectrum of ideas and perspectives regarding the improvement of inservice testing of pumps and valves at nuclear power plants. This document, Volume 1, covers sessions 1A through session 2C. The individual papers have been cataloged separately

Proceedings of the Third NRC/ASME Symposium on Valve and Pump Testing. Session 1A--Session 2C: Volume 1

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

The 1994 Symposium on Valve and Pump Testing, jointly sponsored by the Board of Nuclear Codes and Standards of the American Society of Mechanical Engineers and by the Nuclear Regulatory Commission, provides a forum for the discussion of current programs and methods for inservice testing and motor-operated valve testing at nuclear power plants. The symposium also provides an opportunity to discuss the need to improve that testing in order to help ensure the reliable performance of pumps and valves. The participation of industry representatives, regulators, and consultants results in the discussion of a broad spectrum of ideas and perspectives regarding the improvement of inservice testing of pumps and valves at nuclear power plants. This document, Volume 1, covers sessions 1A through session 2C. The individual papers have been cataloged separately.

Command and Control Rapid Prototyping Continuum (C2RPC): The Framework for Achieving a New C2 Strategy

Science.gov (United States)

2011-06-01

Sync Matrix Assessing J/ADOCS (Fires) TBMCS (ATO) Executing Monitoring (SA) C2 Strategy Objectives • Provide Expanded Mission Management...Computers, and Intelligence T&E Test and Evaluation PMW150 Program Warfare Office Command and Control TBMCS Theater Battle Management Core System POR

Lifetime assessment of atomic-layer-deposited Al2O3-Parylene C bilayer coating for neural interfaces using accelerated age testing and electrochemical characterization.

Science.gov (United States)

Minnikanti, Saugandhika; Diao, Guoqing; Pancrazio, Joseph J; Xie, Xianzong; Rieth, Loren; Solzbacher, Florian; Peixoto, Nathalia

2014-02-01

The lifetime and stability of insulation are critical features for the reliable operation of an implantable neural interface device. A critical factor for an implanted insulation's performance is its barrier properties that limit access of biological fluids to the underlying device or metal electrode. Parylene C is a material that has been used in FDA-approved implantable devices. Considered a biocompatible polymer with barrier properties, it has been used as a substrate, insulation or an encapsulation for neural implant technology. Recently, it has been suggested that a bilayer coating of Parylene C on top of atomic-layer-deposited Al2O3 would provide enhanced barrier properties. Here we report a comprehensive study to examine the mean time to failure of Parylene C and Al2O3-Parylene C coated devices using accelerated lifetime testing. Samples were tested at 60°C for up to 3 months while performing electrochemical measurements to characterize the integrity of the insulation. The mean time to failure for Al2O3-Parylene C was 4.6 times longer than Parylene C coated samples. In addition, based on modeling of the data using electrical circuit equivalents, we show here that there are two main modes of failure. Our results suggest that failure of the insulating layer is due to pore formation or blistering as well as thinning of the coating over time. The enhanced barrier properties of the bilayer Al2O3-Parylene C over Parylene C makes it a promising candidate as an encapsulating neural interface. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Performance test of the I and C system (GSF - 2002) for the irradiation tests using a fuel capsule

Energy Technology Data Exchange (ETDEWEB)

Kang, Young Hwan; Park, S. J.; Kim, B. G.; Ahn, D. H

2004-12-01

HANARO is a very important facility in Korea. It offers various types of irradiation tests of nuclear fuels and materials. With the various applications of the HANARO capsule for the academic and industrial applications, new technologies and relevant facilities will become more important especially for the advanced nuclear fuels and materials development. A new I and C system for an irradiation test using an instrumented fuel capsule have been designed and manufactured to provide more qualified data to fuel developer. The performance test which started in 2004, was done to investigate the thermal response of the capsule connected to the gas mixing system of the new I and C system(GSF-2002) in the cold test loop under the HANARO hydraulic operational condition. Main test parameters are mass flow rate of 25, 50 and 100 cc/min of He/Ne gas, gas pressure of 1 to 3 kg/cm{sup 2}, heater power of 1 to 3.4kW and different gas mixing ratios of He to Ne. From the out-pile tests, it was confirmed that the I and C system(GSF-2002) would be feasible for the fuel irradiation tests. Both analytical and test data prepared by this study are directly used for the fuel experiments related to advanced fuel development program.

Appraisal of the 14C-glycocholate acid test with special reference to the measurement of faecal 14C excretion

International Nuclear Information System (INIS)

Scarpello, J.H.B.; Sladen, G.E.

1977-01-01

The 14 C-glycocholate test, including the measurement of marker corrected faecal 14 C, has been assessed in the following groups of subjects: normal controls (18), patients with diarrhoea not attributable to altered bile acid metabolism (21), patients with diverticula of the small intestine (12), patients with previous resection of ileum and often proximal colon (34), and established ileostomists (10). Patients with diverticular disease had increased breath 14 CO 2 excretion, but normal faecal excretion of 14 C, and this test was more frequently abnormal than the Schilling test. Ileostomists excreted increased amounts of faecal 14 C, even when the ileum was intact and apparently normal. The pattern after resection was complex. Breath 14 C output was normal if the ileal resection was less than 25 cm in length, although some of these patients had increased faecal 14 C excretion if, in addition, at least 15 cm of proximal colon had been resected or by-passed. Longer ileal resections were associated with increased breath and/or faecal 14 C excretion, depending in part on the length of colon resected or by-passed and the 24 hour faecal volume. Fewer than half these patients had both increased breath and faecal excretion of isotope and faecal 14 C alone was occasionally normal with an ileal resection of 50 cm or more. The 14 C-glycocholate test was more frequently abnormal than the Schilling test in this group. The use of faecal marker correction had only a minor impact on the results. These data suggest that, in patients with ileal resection, faecal 14 C, like faecal weight, is determined by the extent of colonic resection as well as by the amount of ileum resected. (author)

DECOVALEX II PROJECT Technical Report - Task 2C

International Nuclear Information System (INIS)

Jing, L.; Stephansson, O.; Chijimatzu, M.; Tsang, C.F.

1999-05-01

The DECOVALEX II project is an international co-operative research project supported by a number of national radioactive waste management organizations of different countries. The project studied four tasks: Task 1: numerical simulation of the RCF3 pump test at Sellafield, UK; Task 2: numerical simulation of the in situ T-H-M experiment at Kamaishi Mine, Japan; Task 3: monitoring of current development in rock fracture research; and Task 4: report on treatment of T-H-M processes in Performance Assessment works for nuclear waste repositories. The project started in 1995 and is scheduled to be finalised in March, 1999. This report concerns the Task 2 of the DECOVALEX H project. Task 2 of the DECOVALEX II project is the numerical modelling of the in-situ T-H-M experiment of a fractured rock - buffer - heater system at Kamaishi Mine, Japan. The experiment was carried out inside a test pit drilled in the floor of a 5 x 7 m alcove excavated near an existing drift at the 550 m level. The test pit has a circular cross section of diameter 1.7 m and a depth of 5 m, filled with bentonite which contains an electric heater. Four research teams studied Task 2 with different computational models. The task is divided into three sub-tasks: Task 2A, Task 2B and Task 2C. Task 2A was defined as a blind prediction to the coupled hydro-mechanical behaviour of the fractured rocks due to the excavation of the test pit. The calibration of the numerical models against measured results of pore pressures, flow rates and rock deformation before filling up of the test pit formed Task 2B. These two sub-tasks were performed to establish well calibrated fields of hydraulic conductivity and mechanical deformability of the fractured rocks at the test site. They were necessary for further simulations on interactions between the rock and buffer materials during heating experiments, as required for Task 2C, with a higher level of confidence on rock mass models. Presented in this report is the

DECOVALEX II PROJECT Technical Report - Task 2C

Energy Technology Data Exchange (ETDEWEB)

Jing, L.; Stephansson, O. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Civil and Environmental Engineering; Boergesson, L. [Clay Technology AB, IDEON Research Center, Lund (Sweden); Chijimatzu, M. [Japan Nuclear Cycle Development Inst., Ibaraki (Japan). Waste Management and Fuel Cycle Research Center; Kautsky, F. [Swedish Nuclear Power Inspectorate (SKI), Stockholm (Sweden); Tsang, C.F. [Lawrence Berkeley National Laboratory, Berkeley, CA (United States). Earth Science Div.

1999-05-01

The DECOVALEX II project is an international co-operative research project supported by a number of national radioactive waste management organizations of different countries. The project studied four tasks: Task 1: numerical simulation of the RCF3 pump test at Sellafield, UK; Task 2: numerical simulation of the in situ T-H-M experiment at Kamaishi Mine, Japan; Task 3: monitoring of current development in rock fracture research; and Task 4: report on treatment ofT-H-M processes in Performance Assessment works for nuclear waste repositories. The project started in 1995 and is scheduled to be finalised in March, 1999. This report concerns the Task 2 of the DECOVALEX H project. Task 2 of the DECOVALEX II project is the numerical modelling of the in-situ T-H-M experiment of a fractured rock - buffer - heater system at Kamaishi Mine, Japan. The experiment was carried out inside a test pit drilled in the floor of a 5 x 7 m alcove excavated near an existing drift at the 550 m level. The test pit has a circular cross section of diameter 1.7 m and a depth of 5 m, filled with bentonite which contains an electric heater. Four research teams studied Task 2 with different computational models. The task is divided into three sub-tasks: Task 2A, Task 2B and Task 2C. Task 2A was defined as a blind prediction to the coupled hydro-mechanical behaviour of the fractured rocks due to the excavation of the test pit. The calibration of the numerical models against measured results of pore pressures, flow rates and rock deformation before filling up of the test pit formed Task 2B. These two sub-tasks were performed to establish well calibrated fields of hydraulic conductivity and mechanical deformability of the fractured rocks at the test site. They were necessary for further simulations on interactions between the rock and buffer materials during heating experiments, as required for Task 2C, with a higher level of confidence on rock mass models. Presented in this report is the definition

Test results for the Oasis 3C high performance water-pumping windmill

Energy Technology Data Exchange (ETDEWEB)

Eggleston, D.M. [DME Engineering, Midland, TX (United States)

1997-12-31

The WINDTech International, L.L.C. Oasis 3C, a 3 m diameter, high-performance water-pumping windmill, was tested at the DME Engineering Wind Test Site just south of Midland, Texas from August through December, 1996. This machine utilizes a 3:1 gearbox with rotating counterweights, similar to a conventional oilfield pumping unit, driven by a multibladed rotor. The rotating counterweight system balances most of the pumping loads and reduces gear loads and starting torque by a factor of at least two and often by a factor of four or more. The torque reduction substantially extends gear and bearing life, and reduces wind speeds required for starting by 30 to 50% or more. The O3C was tested pumping from a quiescent fluid depth of 12.2 m (40 ft) from a 28.3 m (93 ft)-deep well, with additional pumping depth simulated using a pressure regulator valve system. A 9.53 cm (3.75 in.) diameter Harbison-Fischer seal-less single-acting piston pump was used to eliminate pump seal friction as a variable, and standard O3C stroke lengths of 30.5 and 15.2 cm (12 and 6 inches) were used. The regulator spring was set to give a maximum stroke rate of 33 strokes per minute. The water pumped was returned to the well after flowing through a settling tank. The tests were performed in accordance with AWEA WECS testing standards. Instrumentation provided 16 channels of data to accurately measure machine performance, including starting wind speeds, flow rates, O3C azimuth, tail furl angle, wind direction tracking errors, RPM, sucker rod loads, and other variables. The most significant performance data is summarized herein. A mathematical model of machine performance was developed that fairly accurately predicts performance for each of three test conditions. The results verify that the O3C is capable of pumping water at wind speeds from 30% to more than 50% lower than comparable un-counterbalanced units.

Preliminary hydrogeologic assessment of boreholes UE-25c No. 1, UE-25c No. 2, and UE-25c No. 3, Yucca Mountain, Nye County, Nevada

International Nuclear Information System (INIS)

Geldon, A.L.

1993-01-01

The purpose of this report is to characterize the hydrogeology of saturated tuffaceous rocks penetrated by boreholes UE-25c No. 1, UE-25c No.2, and UE-25c No. 3. These boreholes are referred to collectively in this report as the C-holes. The C-holes were drilled to perform multiwell aquifer tests and tracer tests; they comprise the only complex of closely spaced boreholes completed in the saturated zone at Yucca Mountain. Results of lithologic and geophysical logging, fracture analyses, water-level monitoring, temperature and tracejector surveys, aquifer tests, and hydrochemical sampling completed at the C-hole complex as of 1986 are assessed with respect to the regional geologic and hydrologic setting. A conceptual hydrogeological model of the Yucca Mountain area is presented to provide a context for quantitatively evaluating hydrologic tests performed at the C-hole complex as of 1985, for planning and interpreting additional hydrologic tests at the C-hole complex, and for possibly re-evaluating hydrologic tests in boreholes other than the C-holes

Preliminary hydrogeologic assessment of boreholes UE-25c No. 1, UE-25c No. 2, and UE-25c No. 3, Yucca Mountain, Nye County, Nevada

International Nuclear Information System (INIS)

Geldon, A.L.

1993-01-01

The purpose of this report is to characterize-the hydrogeology of saturated tuffaceous rocks penetrated by boreholes UE-25c number-sign 1, UE-25c number-sign 2, and UE-25c number-sign 3. These boreholes are referred to collectively in this report as the C-holes. The C-holes were drilled to perform multiwell aquifer tests and tracer tests; they comprise the only complex of closely spaced boreholes completed in the saturated zone at Yucca Mountain. Results of lithologic and geophysical logging, fracture analyses, water-level monitoring, temperature and tracejector surveys aquifer tests, and hydrochemical sampling completed at the C-hole complex as of 1986 are assessed with respect to the regional geologic and hydrologic setting. A conceptual hydrogeological model of the Yucca Mountain area is presented to provide a context for quantitatively evaluating hydrologic tests performed at the C-hole complex as of 1985, for planning and interpreting additional hydrologic tests at the C-hole complex, and for possibly re-evaluating hydrologic tests in boreholes other than the C-holes

COMPARATIVE STUDY TO FIND THE EFFECT OF MULLIGANS SNAG TECHNIQUE (C1-C2 VERSUS MAITLANDS TECHNIQUE (C1-C2 IN CERVICOGENIC HEADACHE AMONG INFORMATION TECHNOLOGY PROFESSIONALS

Directory of Open Access Journals (Sweden)

Neeti Christian

2017-06-01

Full Text Available Background: Headache is a common condition which physiotherapists have to deal with in clinical practice.Headaches which arise from the cervical spine are termed as Cervicogenic headaches (CGH, and these types of headaches are common form of a chronic and recurrent headache.The diagnostic criteria for CGH are outlined by the IHS (International Headache Society. The upper cervical joints, namely the occiput-C1 and C1-C2 segments are the most common origin of pain. Office and computer workers have the highest incidence of neck disorders than other occupations; the prevalence of neck disorders is above 50% among them. The purpose of this study is to find the effectiveness of Mulligan’s SNAG technique (C1-C2 and Maitland’s technique (C1-C2 in CGH and to compare these manual therapy techniques (Mulligan’s SNAG technique and Maitland’s technique with a control group. Methods: 30 subjects were selected for the study among them 23 subjects completed the study. The subjects were randomly allocated to 3 groups. The range of motion (ROM and severity of a headache were assessed pre and post intervention using FRT and HDI respectively. Result: The comparison revealed that SNAG group had a greater increase in cervical rotation (p<0.01 range than the Maitland’s technique and control groups. The mean value between pre-post differences shows a decrease in severity of a headache among all three groups. The significant difference between 3 groups was found through Tukey’s post hoc test using ANOVA method (Group A versus Group C; p<0.01 and Group B versus Group C; p<0.05. Conclusion: The present study suggested that C1-C2 SNAG technique showed statistically significant improvement in reducing headache and disability when compared to the Maitland’s mobilization technique among cervicogenic headache subjects

Eddy-current testing of fatigue degradation upon contact fatigue loading of gas powder laser clad NiCrBSi-Cr3C2 composite coating

Science.gov (United States)

Savrai, R. A.; Makarov, A. V.; Gorkunov, E. S.; Soboleva, N. N.; Kogan, L. Kh.; Malygina, I. Yu.; Osintseva, A. L.; Davydova, N. A.

2017-12-01

The possibilities of the eddy-current method for testing the fatigue degradation under contact loading of gas powder laser clad NiCrBSi-Cr3C2 composite coating with 15 wt.% of Cr3C2 additive have been investigated. It is shown that the eddy-current testing of the fatigue degradation under contact loading of the NiCrBSi-15%Cr3C2 composite coating can be performed at high excitation frequencies 72-120 kHz of the eddy-current transducer. At that, the dependences of the eddy-current instrument readings on the number of loading cycles have both downward and upward branches, with the boundary between the branches being 3×105 cycles in the given loading conditions. This is caused, on the one hand, by cracking, and, on the other hand, by cohesive spalling and compaction of the composite coating, which affect oppositely the material resistivity and, correspondingly, the eddy-current instrument readings. The downward branch can be used to monitor the processes of crack formation and growth, the upward branch - to monitor the degree of cohesive spalling, while taking into account in the testing methodology an ambiguous character of the dependences of the eddy-current instrument readings on the number of loading cycles.

SEE locomotor behavior test discriminates C57BL/6J and DBA/2J mouse inbred strains across laboratories and protocol conditions.

Science.gov (United States)

Kafkafi, Neri; Lipkind, Dina; Benjamini, Yoav; Mayo, Cheryl L; Elmer, Gregory I; Golani, Ilan

2003-06-01

Conventional tests of behavioral phenotyping frequently have difficulties differentiating certain genotypes and replicating these differences across laboratories and protocol conditions. This study explores the hypothesis that automated tests can be designed to quantify ethologically relevant behavior patterns that more readily characterize heritable and replicable phenotypes. It used SEE (Strategy for the Exploration of Exploration) to phenotype the locomotor behavior of the C57BL/6 and DBA/2 mouse inbred strains across 3 laboratories. The 2 genotypes differed in 15 different measures of behavior, none of which had a significant genotype-laboratory interaction. Within the same laboratory, most of these differences were replicated in additional experiments despite the test photoperiod phase being changed and saline being injected. Results suggest that well-designed tests may considerably enhance replicability across laboratories.

Stable Sheave Moduli of Rank 2 with Chern Classes c 1 = -1; c2 = 2; c3 = 0 on Q3

Directory of Open Access Journals (Sweden)

A. D. Uvarov

2012-01-01

Full Text Available In this paper we consider the scheme MQ( 2;¡1; 2; 0 of stable torsion free sheaves of rank 2 with Chern classes c1 = -1, c2 = 2, c3 = 0 on a smooth 3-dimensional projective quadric Q. The manifold MQ(-1; 2 of moduli bundles of rank 2 with Chern classes c1 = -1, c2 = 2 on Q was studied by Ottaviani and Szurek in 1994. In 2007 the author described the closure MQ (-1; 2 in the scheme MQ(2;¡1; 2; 0. In this paper we prove that in MQ(2;¡1; 2; 0 there exists a unique irreducible component diferent from MQ (¡1; 2 which is a rational variety of dimension 10.

Vaccination with canine parvovirus type 2 (CPV-2) protects against challenge with virulent CPV-2b and CPV-2c.

Science.gov (United States)

Siedek, Elisabeth M; Schmidt, Holger; Sture, Gordon H; Raue, Rüdiger

2011-01-01

Mutations in canine parvovirus (CPV) field isolates have created concerns regarding the ability of vaccines containing CPV-2 to protect against infection with the newly identified antigenic types CPV-2b and CPV-2c. To address this concern, the efficacy of CPV-2 strain NL-35-D currently in use as a commercial vaccine was demonstrated against an oral challenge with CPV-2b and CPV-2c, respectively. Clinically healthy specific pathogen free Beagle dogs were either vaccinated or treated with water for injection first at 8-9 weeks of age and again at 11-12 weeks of age. All dogs were challenged either with CPV-2b or CPV-2c three weeks after the second vaccination. During the two week period following challenge, clinical signs, white blood cell counts, serology by haemagglutination inhibition (HI) and serum neutralisation tests, and virus shedding by haemagglutination test were assessed. All control dogs developed clinical signs of parvovirosis (including pyrexia and leucopenia) and shed virus. Vaccinated dogs seroconverted (HI titres > or =80), remained healthy throughout the study and shed more than 100 times less virus than controls. In conclusion, vaccination with the low passage, high titre CPV-2 strain NL-35-D cross-protects dogs against virulent challenges with CPV-2b or CPV-2c by preventing disease and substantially reducing viral shedding.

Test Operations Procedure (TOP) 08-2-188 Chemical Point Detector Vapor Testing

Science.gov (United States)

2018-04-27

Final 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Test Operations Procedure (TOP) 08-2-188 Chemical Point Detector Vapor Testing 5a. CONTRACT...NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING...ORGANIZATION NAME(S) AND ADDRESS(ES) US Army Dugway Proving Ground West Desert Test Center (TEDT-DPW) Dugway, UT 84022-5000 8. PERFORMING ORGANIZATION

The structure of C2b, a fragment of complement component C2 produced during C3 convertase formation

Energy Technology Data Exchange (ETDEWEB)

Krishnan, Vengadesan [Center for Biophysical Sciences and Engineering, School of Optometry, University of Alabama at Birmingham, Birmingham, AL 35294 (United States); Xu, Yuanyuan [Division of Clinical Immunology and Rheumatology, University of Alabama at Birmingham, Birmingham, AL 35294 (United States); Macon, Kevin [Center for Biophysical Sciences and Engineering, School of Optometry, University of Alabama at Birmingham, Birmingham, AL 35294 (United States); Volanakis, John E. [Department of Medicine, University of Alabama at Birmingham, Birmingham, AL 35294 (United States); Narayana, Sthanam V. L., E-mail: narayana@uab.edu [Center for Biophysical Sciences and Engineering, School of Optometry, University of Alabama at Birmingham, Birmingham, AL 35294 (United States)

2009-03-01

The crystal structure of C2b has been determined at 1.8 Å resolution, which reveals the arrangement of its three complement control protein (CCP) modules. A model for complement component C2 is presented and its conformational changes during the C3-convertase formation are also discussed. The second component of complement (C2) is a multi-domain serine protease that provides catalytic activity for the C3 and C5 convertases of the classical and lectin pathways of human complement. The formation of these convertases requires the Mg{sup 2+}-dependent binding of C2 to C4b and the subsequent cleavage of C2 by C1s or MASP2, respectively. The crystal structure of full-length C2 is not yet available, although the structure of its C-terminal catalytic segment C2a has been determined. The crystal structure of the N-terminal segment C2b of C2 determined to 1.8 Å resolution presented here reveals the arrangement of its three CCP domains. The domains are arranged differently compared with most other CCP-domain assemblies, but their arrangement is similar to that found in the Ba part of the full-length factor B structure. The crystal structures of C2a, C2b and full-length factor B are used to generate a model for C2 and a discussion of the domain association and possible interactions with C4b during formation of the C4b–C2 complex is presented. The results of this study also suggest that upon cleavage by C1s, C2a domains undergo conformational rotation while bound to C4b and the released C2b domains may remain folded together similar to as observed in the intact protein.

The structure of C2b, a fragment of complement component C2 produced during C3 convertase formation

International Nuclear Information System (INIS)

Krishnan, Vengadesan; Xu, Yuanyuan; Macon, Kevin; Volanakis, John E.; Narayana, Sthanam V. L.

2009-01-01

The crystal structure of C2b has been determined at 1.8 Å resolution, which reveals the arrangement of its three complement control protein (CCP) modules. A model for complement component C2 is presented and its conformational changes during the C3-convertase formation are also discussed. The second component of complement (C2) is a multi-domain serine protease that provides catalytic activity for the C3 and C5 convertases of the classical and lectin pathways of human complement. The formation of these convertases requires the Mg 2+ -dependent binding of C2 to C4b and the subsequent cleavage of C2 by C1s or MASP2, respectively. The crystal structure of full-length C2 is not yet available, although the structure of its C-terminal catalytic segment C2a has been determined. The crystal structure of the N-terminal segment C2b of C2 determined to 1.8 Å resolution presented here reveals the arrangement of its three CCP domains. The domains are arranged differently compared with most other CCP-domain assemblies, but their arrangement is similar to that found in the Ba part of the full-length factor B structure. The crystal structures of C2a, C2b and full-length factor B are used to generate a model for C2 and a discussion of the domain association and possible interactions with C4b during formation of the C4b–C2 complex is presented. The results of this study also suggest that upon cleavage by C1s, C2a domains undergo conformational rotation while bound to C4b and the released C2b domains may remain folded together similar to as observed in the intact protein

Design Feature and Prototype Testing Methodology of DHIC's Nuclear I and C System

International Nuclear Information System (INIS)

Kim, K.H.; Baeg, S.Y.; Kim, S.A.; Lee, S.J.; Yoon, S.P.; Park, C.Y.

2011-01-01

The DHIC has developed an I and C system for a nuclear power plant through a Korean Government R and D project since 2001. This I and C system was designed and implemented to be applied for the new 1400MW nuclear power plant of KHNP. This system's design is based on the class-1E PLC platform and the non-class1E DCS platform. The PPS, the ESF-CCS, the RCOPS, the QIAS-P/N, the PCS, the NPCS, the P-CCS and the NIMS were designed, implemented and tested. The R and D project has been developed under a systematic and guided QA plan, but it is not easy to be applied for a new NPP such as Shin-Ulchin 1 and 2. To resolve problems of the first-application concerns, a new idea of integrated performance testing was adopted. A main control room for a verification test facility was constructed and it has features of a compact, video-based man-machine interface. The MCR includes five operation consoles, a Large Display Panel. A test system for a verification test facility is implemented as similar as a control and protection system of SUN 1 and 2. Integration level tests such as a system test, an interface test, a MMI test, a system function/performance test, a failure mode test, a response time test, a network load test, an alarm test, a reactor power cutback system test, an unit load transient test and a scenario test were performed using the prototype test facilities. These kinds of testing can verify and pre-validate the integrated I and C system's performance and flexibility. It could offer an implementation training before construction and also minimize trial errors to be found in the site. (author)

RELAP5/MOD2 code assessment for the Semiscale Mod-2C Test S-LH-1

International Nuclear Information System (INIS)

Fineman, C.P.

1986-01-01

RELAP5/MOD2, Cycle 36.02, was assessed using data from Semiscale Mod-2C experiment S-LH-1. The major phenomena that occurred during the experiment were calculated by RELAP5/MOD2, although the duration and the magnitude of their effect on the transient were not always well calculated. Areas defined where further work was needed to improve the RELAP5 calculation include: (1) the system energy balance, (2) core interfacial drag, and 3) the heat transfer logic rod dryout criterion

Novel Use of Pharmacogenetic Testing in the Identification of CYP2C9 Polymorphisms Related to NSAID-Induced Gastropathy.

Science.gov (United States)

Gupta, Anita; Zheng, Lu; Ramanujam, Vendhan; Gallagher, John

2015-05-01

To illustrate the potential value of pharmacogenetic testing to identify patients at risk for nonsteroidal anti-inflammatory drug-induced gastropathy. Case report. We report a case encountered in an outpatient setting for pain management. We present a case of a patient treated with celecoxib who developed severe nonsteroidal anti-inflammatory drug-induced gastropathy. Suspecting a relation between this adverse event and altered drug metabolism, pharmacogenetic testing was performed to assess the role of the cytochrome P450 (CP450) enzyme profile. Pharmacogenetic testing revealed a relation between this adverse event and an allelic variant of cytochrome P450, CYP2C9, subsequently leading to discontinuation of the drug along with counseling to caution the patient to avoid the use of celecoxib and other drugs metabolized by the same enzyme. Although pharmacogenetic testing is not routinely used in clinical decision making, pain physicians must be aware of the potential benefits of this testing for managing patients with pain, and to improve drug efficacy and safety profile. Wiley Periodicals, Inc.

Study of the unimolecular decompositions of the (C3H6)+2 and (c-C3H6)+2 complexes

International Nuclear Information System (INIS)

Tzeng, W.; Ono, Y.; Linn, S.H.; Ng, C.Y.

1985-01-01

The major product channels identified in the unimolecular decompositions ofC 3 H + 6 xC 3 H 6 and c-C 3 H + 6 xc-C 3 H 6 in the total energy [neutral (C 3 H 6 ) 2 or (c-C 3 H 6 ) 2 heat of formation plus excitation energy] range of approx.230--450 kcal/mol are C 3 H + 7 +C 3 H 5 , C 4 H + 7 +C 2 H 5 , C 4 H + 8 +C 2 H 4 , and C 5 H + 9 +CH 3 . The measured appearance energy for C 4 H + 7 (9.54 +- 0.04 eV) from (C 3 H 6 ) 2 is equal to the thermochemical threshold for the formation of C 4 H + 7 +C 2 H 5 from (C 3 H 6 ) 2 , indicating that the exit potential energy barrier for the ion--molecule reaction C 3 H + 6 +C 3 H 6 →C 4 H + 7 +C 2 H 5 is negligible. There is evidence that the formations of C 4 H + 7 +C 2 H 4 +H from (C 3 H 6 ) + 2 and (c-C 3 H 6 ) + 2 also proceed with high probabilities when they are energetically allowed. The variations of the relative abundances for C 4 H + 7 ,C 4 H + 8 , and C 5 H + 9 from (C 3 H 6 ) + 2 and (c-C 3 H 6 ) + 2 as a function of ionizing photon energy are in qualitative agreement, suggesting that (C 3 H 6 ) + 2 and (c-C 3 H 6 ) + 2 rearrange to similar C 6 H + 12 isomers prior to fragmentation. The fact that C 6 H + 11 is found to be a primary ion from the unimolecular decomposition of (c-C 3 H 6 ) + 2 but not (C 3 H 6 ) + 2 supports the conclusion that the distribution of C 6 H + 12 collision complexes involved in the C 3 H + 6 +C 3 H 6 reactions is different from that in the cyclopropane ion--molecule reactions

Depressurisation studies. Phase 2: results of Tests 127 and 128

International Nuclear Information System (INIS)

Edwards, A.R.; Borgartz, B.O.; Goodman, R.M.E.; O'Brien, T.P.; Rawlingson, M.

1978-06-01

A basic experimental programme involving the sudden depressurisation of a simple pipe system containing water at 3.45 to 17.24MPa pressure and temperature in the range of 200 to 250 0 C has been concluded. Measurements were made of the transient density, pressure, and temperature variations in a two phase fluid in the system during discharge. Phase 1 tests investigated blowdown from straight pipes 4m long with constant internal diameters of 73 and 32 mm. Phase 2 tests incorporated a reservoir added to the 32mm pipe. In this, the second of three reports on Phase 2 tests, the test assembly, instrumentation and experimental procedure are briefly described. The conditions and results are reported for two of the tests in which the liquid in the long discharge pipe was initially subcooled by 10 0 C and 15 0 C while the reservoir was at saturation conditions with a steam dome present. (UK)

[2,4-(13)C]β-hydroxybutyrate metabolism in astrocytes and C6 glioblastoma cells.

Science.gov (United States)

Eloqayli, Haytham; Melø, Torun M; Haukvik, Anne; Sonnewald, Ursula

2011-08-01

This study was undertaken to determine if the ketogenic diet could be useful for glioblastoma patients. The hypothesis tested was whether glioblastoma cells can metabolize ketone bodies. Cerebellar astrocytes and C6 glioblastoma cells were incubated in glutamine and serum free medium containing [2,4-(13)C]β-hydroxybutyrate (BHB) with and without glucose. Furthermore, C6 cells were incubated with [1-(13)C]glucose in the presence and absence of BHB. Cell extracts were analyzed by mass spectrometry and media by (1)H magnetic resonance spectroscopy and HPLC. Using [2,4-(13)C]BHB and [1-(13)C]glucose it could be shown that C6 cells, in analogy to astrocytes, had efficient mitochondrial activity, evidenced by (13)C labeling of glutamate, glutamine and aspartate. However, in the presence of glucose, astrocytes were able to produce and release glutamine, whereas this was not accomplished by the C6 cells, suggesting lack of anaplerosis in the latter. We hypothesize that glioblastoma cells kill neurons by not supplying the necessary glutamine, and by releasing glutamate.

Summary of the Minor Actinide-bearing MOX AFC-2C and -2D Irradiations

International Nuclear Information System (INIS)

McClellan, Kenneth; Chichester, Heather; Hayes, Steve; Voit, Stewart

2013-01-01

Summary of AFC-2C and AFC-2D tests: • AFC-2C and 2D, 1st MOX experiments in FCRD, were irradiated in ATR; • Initial results indicate performance of experimental MA-MOX fuels are similar to standard FR MOX fuels; • Cd-shrouded ATR experiment assembly and 235 U enrichment produce prototypic fast reactor power and temperature profiles leading to classic MOX zone restructuring; • Baseline postirradiation examinations have been completed for AFC-2C MOX and MA-MOX fuels; • Future work includes: – PIE of AFC-2D; – compare results to prototypic MOX fuel performance; – electron microscopy for microstructure and constituent distribution; – advanced NDE on saved pins

Interactive test tool for interoperable C-ITS development

NARCIS (Netherlands)

Voronov, A.; Englund, C.; Bengtsson, H.H.; Chen, L.; Ploeg, J.; Jongh, J.F.C.M. de; Sluis, H.J.D. van de

2015-01-01

This paper presents the architecture of an Interactive Test Tool (ITT) for interoperability testing of Cooperative Intelligent Transport Systems (C-ITS). Cooperative systems are developed by different manufacturers at different locations, which makes interoperability testing a tedious task. Up until

Comparison of test performance profile for blood tests of liver fibrosis in chronic hepatitis C.

Science.gov (United States)

Halfon, Philippe; Bacq, Yannick; De Muret, Anne; Penaranda, Guillaume; Bourliere, Marc; Ouzan, Denis; Tran, Albert; Botta, Danielle; Renou, Christophe; Bréchot, Marie-Claude; Degott, Claude; Paradis, Valérie

2007-03-01

We evaluated the test performance profile (TPP) of blood tests of liver fibrosis. Three hundred and fifty-six patients with C chronic hepatitis were included in two centers. Metavir staging of liver specimens by two independent pathologists and the following tests were evaluated: Fibrotest (FT), APRI, FibroMeter (FM), and Hepascore (HS). Metavir stages were: F0: 4%, F1: 55%, F2: 26%, F3: 11%, and F4: 4%. The AUROCs were not significantly different, respectively, FT, FM, APRI, HS: >or=F2: 0.79, 0.78, 0.76, >or=0.76; F3: 0.81, 0.85, 0.81, 0.81; and F4: 0.86, 0.94, 0.92, 0.89. The TPP relies on the paired comparison of blood-test misclassification based on liver specimen, e.g. FT vs FM, respectively: F0+1: 18 vs 28% (p=0.0003), >or=F2: 43 vs 31% (p=0.004). There was no center effect. In those populations, the four blood tests had a similar performance for significant fibrosis (F>or=2), lying in the lower range of published results which is attributable to a low >or=F2 prevalence, and for >or=F3 and F4. However, FM and FT had performance profiles significantly different as a function of fibrosis stages or diagnostic target (fibrosis cut-off). This has to be considered during the interpretation process. Moreover, the performance should be reported with different diagnostic targets.

Identification of rabbit cytochromes P450 2C1 and 2C2 as arachidonic acid epoxygenases.

Science.gov (United States)

Laethem, R M; Koop, D R

1992-12-01

Microsomes prepared from COS-1 cells transiently expressing rabbit cytochromes P450 2C1 and 2C2 catalyzed the metabolism of arachidonic acid to predominantly 11,12- and 14,15-epoxyeicosatrienoic acids (EETs) when microsomal epoxide hydrolase activity was inhibited by 0.2 mM 1,2-epoxy-3,3,3-trichloropropane. P450 2C2 catalyzed the formation of 11,12-EET and 14,15-EET at a ratio of 3.0 and also produced 19-hydroxyeicosatetraenoic acid (19-HETE). The 11,12-EET, 14,15-EET, and 19-HETE represented 48.3, 15.9, and 12.8%, respectively, of the total metabolites formed. P450 2C1 produced a similar but distinct ratio of 11,12-EET to 14,15-EET (2.0) and did not produce any detectable 19-HETE. The 11,12-EET and 14,15-EET represented 63.0 and 31.1%, respectively, of the total metabolites formed. The 8,9- and 5,6-EETs were not detected with either enzyme. The ratio of the 11,12-EET to 14,15-EET was 1.5 with P450 2CAA, a P450 arachidonic acid epoxygenase (P450 2CAA) that had an amino-terminal sequence identical to that of P450 2C2 [J. Biol. Chem. 267:5552-5559 (1992)]. P450 2C1, 2C2, and 2CAA metabolized lauric acid. The ratio of omega-1- to omega-hydroxylated laurate was 3.6, 3.4, and 2.4 for P450 2CAA, P450 2C2, and P450 2C1, respectively. Purified P450 2CAA had a slightly greater apparent molecular weight than expressed P450 2C2 on sodium dodecyl sulfate-polyacrylamide gels. The results clearly establish that rabbit P450 2C1 and 2C2 are arachidonic acid epoxygenases, and they suggest that P450 2CAA and 2C2 are very similar but may not be identical isoforms.

Report on the Fracture Analysis of HfB(sub 2)-SiC and ZrB(sub 2)-SiC Composites; TOPICAL

International Nuclear Information System (INIS)

MECHOLSKY, JR. JOHN J.

2001-01-01

Hafnium diboride-silicon carbide (HS) and zirconium diboride-silicon carbide (ZS) composites are potential materials for high temperature, thermal shock applications such as for components on re-entry vehicles. In order to establish material constants necessary for evaluation of in situ fracture, bars fractured in four-point flexure were examined using fractographic principles. The fracture toughness was determined from measurements of the critical crack sizes and the strength values and the crack branching constants were established to use in forensic fractography for future in-flight tests. The fracture toughnesses range from about 13 MPam(sup 1/2) at room temperature to about 6 MPam(sup 1/2) at 1400 C for ZrB(sub 2)-Sic composites and from about 13 MPam(sup 1/2) at room temperature to about 4 MPam(sup 1/2) at 1400 C for HfB(sub 2)-SiC composites. Thus, the toughnesses of either the HS or ZS composites have the potential for use in thermal shock applications. Processing and manufacturing defects limited the strength of the test bars. However, examination of the microstructure on the fracture surfaces shows that the processing of these composites can be improved. There is potential for high toughness composites with high strength to be used in thermal shock conditions if the processing and handling are controlled

Synthesis and Isolation of the Titanium-Scandium Endohedral Fullerenes-Sc2 TiC@Ih -C80 , Sc2 TiC@D5h -C80 and Sc2 TiC2 @Ih -C80 : Metal Size Tuning of the Ti(IV) /Ti(III) Redox Potentials.

Science.gov (United States)

Junghans, Katrin; Ghiassi, Kamran B; Samoylova, Nataliya A; Deng, Qingming; Rosenkranz, Marco; Olmstead, Marilyn M; Balch, Alan L; Popov, Alexey A

2016-09-05

The formation of endohedral metallofullerenes (EMFs) in an electric arc is reported for the mixed-metal Sc-Ti system utilizing methane as a reactive gas. Comparison of these results with those from the Sc/CH4 and Ti/CH4 systems as well as syntheses without methane revealed a strong mutual influence of all key components on the product distribution. Whereas a methane atmosphere alone suppresses the formation of empty cage fullerenes, the Ti/CH4 system forms mainly empty cage fullerenes. In contrast, the main fullerene products in the Sc/CH4 system are Sc4 C2 @C80 (the most abundant EMF from this synthesis), Sc3 C2 @C80 , isomers of Sc2 C2 @C82 , and the family Sc2 C2 n (2 n=74, 76, 82, 86, 90, etc.), as well as Sc3 CH@C80 . The Sc-Ti/CH4 system produces the mixed-metal Sc2 TiC@C2 n (2 n=68, 78, 80) and Sc2 TiC2 @C2 n (2 n=80) clusterfullerene families. The molecular structures of the new, transition-metal-containing endohedral fullerenes, Sc2 TiC@Ih -C80 , Sc2 TiC@D5h -C80 , and Sc2 TiC2 @Ih -C80 , were characterized by NMR spectroscopy. The structure of Sc2 TiC@Ih -C80 was also determined by single-crystal X-ray diffraction, which demonstrated the presence of a short Ti=C double bond. Both Sc2 TiC- and Sc2 TiC2 -containing clusterfullerenes have Ti-localized LUMOs. Encapsulation of the redox-active Ti ion inside the fullerene cage enables analysis of the cluster-cage strain in the endohedral fullerenes through electrochemical measurements. © 2016 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Activated Integrin-Linked Kinase Negatively Regulates Muscle Cell Enhancement Factor 2C in C2C12 Cells

Directory of Open Access Journals (Sweden)

Zhenguo Dong

2015-01-01

Full Text Available Our previous study reported that muscle cell enhancement factor 2C (MEF2C was fully activated after inhibition of the phosphorylation activity of integrin-linked kinase (ILK in the skeletal muscle cells of goats. It enhanced the binding of promoter or enhancer of transcription factor related to proliferation of muscle cells and then regulated the expression of these genes. In the present investigation, we explored whether ILK activation depended on PI3K to regulate the phosphorylation and transcriptional activity of MEF2C during C2C12 cell proliferation. We inhibited PI3K activity in C2C12 with LY294002 and then found that ILK phosphorylation levels and MEF2C phosphorylation were decreased and that MCK mRNA expression was suppressed significantly. After inhibiting ILK phosphorylation activity with Cpd22 and ILK-shRNA, we found MEF2C phosphorylation activity and MCK mRNA expression were increased extremely significantly. In the presence of Cpd22, PI3K activity inhibition increased MEF2C phosphorylation and MCK mRNA expression indistinctively. We conclude that ILK negatively and independently of PI3K regulated MEF2C phosphorylation activity and MCK mRNA expression in C2C12 cells. The results provide new ideas for the study of classical signaling pathway of PI3K-ILK-related proteins and transcription factors.

Minimally invasive (13)C-breath test to examine phenylalanine metabolism in children with phenylketonuria.

Science.gov (United States)

Turki, Abrar; Murthy, Gayathri; Ueda, Keiko; Cheng, Barbara; Giezen, Alette; Stockler-Ipsiroglu, Sylvia; Elango, Rajavel

2015-01-01

Phenylketonuria (PKU) is an autosomal recessive disorder caused by deficiency of hepatic phenylalanine hydroxylase (PAH) leading to increased levels of phenylalanine in the plasma. Phenylalanine levels and phenylalanine hydroxylase (PAH) activity monitoring are currently limited to conventional blood dot testing. 1-(13)C-phenylalanine, a stable isotope can be used to examine phenylalanine metabolism, as the conversion of phenylalanine to tyrosine occurs in vivo via PAH and subsequently releases the carboxyl labeled (13)C as (13)CO2 in breath. Our objective was to examine phenylalanine metabolism in children with PKU using a minimally-invasive 1-(13)C-phenylalanine breath test ((13)C-PBT). Nine children (7 M: 2 F, mean age 12.5 ± 2.87 y) with PKU participated in the study twice: once before and once after sapropterin supplementation. Children were provided 6 mg/kg oral dose of 1-(13)C-phenylalanine and breath samples were collected at 20 min intervals for a period of 2h. Rate of CO2 production was measured at 60 min post-oral dose using indirect calorimetry. The percentage of 1-(13)C-phenylalanine exhaled as (13)CO2 was measured over a 2h period. Prior to studying children with PKU, we tested the study protocol in healthy children (n = 6; 4M: 2F, mean age 10.2 ± 2.48 y) as proof of principle. Production of a peak enrichment (Cmax) of (13)CO2 (% of dose) in all healthy children occurred at 20 min ranging from 17-29% of dose, with a subsequent return to ~5% by the end of 2h. Production of (13)CO2 from 1-(13)C-phenylalanine in all children with PKU prior to sapropterin treatment remained low. Following sapropterin supplementation for a week, production of (13)CO2 significantly increased in five children with a subsequent decline in blood phenylalanine levels, suggesting improved PAH activity. Sapropterin treatment was not effective in three children whose (13)CO2 production remained unchanged, and did not show a reduction in blood phenylalanine levels and improvement

Cryptanalysis of C2

DEFF Research Database (Denmark)

Borghoff, Julia; Knudsen, Lars Ramkilde; Leander, Gregor

2009-01-01

We present several attacks on the block cipher C2, which is used for encrypting DVD Audio discs and Secure Digital cards. C2 has a 56 bit key and a secret 8 to 8 bit S-box. We show that if the attacker is allowed to choose the key, the S-box can be recovered in 2^24 C2 encryptions. Attacking the 56...... bit key for a known S-box can be done in complexity 2^48. Finally, a C2 implementation with a 8 to 8 bit secret S-box (equivalent to 2048 secret bits) and a 56 bit secret key can be attacked in 2^53.5 C2 encryptions on average....

Using Testlet Response Theory to Examine Local Dependence in C-Tests

Science.gov (United States)

Eckes, Thomas; Baghaei, Purya

2015-01-01

C-tests are gap-filling tests widely used to assess general language proficiency for purposes of placement, screening, or provision of feedback to language learners. C-tests consist of several short texts in which parts of words are missing. We addressed the issue of local dependence in C-tests using an explicit modeling approach based on testlet…

Fracture testing and performance of beryllium copper alloy C17510

International Nuclear Information System (INIS)

Murray, H.A.; Zatz, I.J.

1994-05-01

When a literature search and discussion with manufacturers revealed that there was virtually no existing data related to the fracture properties and behavior of copper beryllium alloy C17510, a series of test programs was undertaken to ascertain this information for several variations in material processing and chemistry. These variations in C17510 were primarily optimized for combinations of strength and conductivity. While originally intended for use as cyclically loaded high-field, high-strength conductors in fusion energy research, material testing of C17510 has indicated that it is an attractive and economical alternative for a host of other structural, mechanical and electrical applications. ASTM tests performed on three variations of C17510 alloys included both J-integral and plane strain fracture toughness testing and fatigue crack growth rate tests, as well as verifying tensile, hardness, Charpy, and other well defined mechanical properties. Fracture testing was performed at both room and liquid nitrogen temperatures, which bound the thermal environment anticipated for the fusion components being designed. Fatigue crack propagation stress ratios ranged from nominal zero to minus one at each temperature. In order to confirm the test results, duplicate and independent test programs were awarded to separate facilities with appropriate test experience, whenever possible. The primary goal of the test program, to determine and bound the fracture toughness and Paris constants for C17510,was accomplished. In addition, a wealth of information was accumulated pertaining to crack growth characteristics, effects of directionality and potential testing pitfalls. The paper discusses the test program and its findings in detail

On the sintering behaviour of steel bonded TiC-Cr3C2 and TiC-Cr3C2-WC mixed carbides

International Nuclear Information System (INIS)

Stojanov, L.G.; Exner, H.E.

1978-01-01

Powder mixtures of TiC+Cr 3 C 2 and TiC+Cr 3 C 2 + WC were hot pressed to nearly full density. The lattice parameter of the resulting cubic mixed crystal decreases linearly with increasing additions of Cr 3 C 2 and (Cr 3 C 2 +WC 1:1). Microhardness increases with Cr 3 C 2 content up to 20 wt.%. By addition of WC, microhardness is increased further and reaches a maximum value of approx. 38 000 MN/m 2 for 20 wt.% Cr 3 C 2 and 20 wt.% WC. From these solid solutions powder compositions of Ferro-TiC type were produced by milling with 55 wt.% Fe and 0.4 wt.% C. The sintering behaviour of these powders was studied in a vacuum dilatometer. The pronounced increase of shrinkage by Cr 3 C 2 and higher amounts of Cr 3 C 2 +WC dissolved in TiC previous to binder phase melting is attributed to the increased solubility of the carbide in solid iron. Presintering at 700 0 C in hydrogen has a negative influence on sintering activity and requires much higher temperatures for complete densification during subsequent vacuum sintering. (orig.) [de

Comparison of Accuracy Between 13C- and 14C-Urea Breath Testing: Is an Indeterminate-Results Category Still Needed?

Science.gov (United States)

Charest, Mathieu; Bélair, Marc-André

2017-06-01

Helicobacter pylori infection is the leading cause of peptic ulcer disease. The purpose of this study was, first, to assess the difference in the distribution of negative versus positive results between the older 14 C-urea breath test and the newer 13 C-urea breath test and, second, to determine whether use of an indeterminate-results category is still meaningful and what type of results should trigger repeated testing. Methods: A retrospective survey was performed of all consecutive patients referred to our service for urea breath testing. We analyzed 562 patients who had undergone testing with 14 C-urea and 454 patients who had undergone testing with 13 C-urea. Results: In comparison with the wide distribution of negative 14 C results, negative 13 C results were distributed farther from the cutoff and were grouped more tightly around the mean negative value. Distribution analysis of the negative results for 13 C testing, compared with those for 14 C testing, revealed a statistically significant difference between the two. Within the 13 C group, only 1 patient could have been classified as having indeterminate results using the same indeterminate zone as was used for the 14 C group. This is significantly less frequent than what was found for the 14 C group. Discussion: Borderline-negative results do occur with 13 C-urea breath testing, although less frequently than with 14 C-urea breath testing, and we will be carefully monitoring differences falling between 3.0 and 3.5 %Δ. 13 C-urea breath testing is safe and simple for the patient and, in most cases, provides clearer positive or negative results for the clinician. © 2017 by the Society of Nuclear Medicine and Molecular Imaging.

10 MW Supercritical CO2 Turbine Test

Energy Technology Data Exchange (ETDEWEB)

Turchi, Craig

2014-01-29

The Supercritical CO2 Turbine Test project was to demonstrate the inherent efficiencies of a supercritical carbon dioxide (s-CO2) power turbine and associated turbomachinery under conditions and at a scale relevant to commercial concentrating solar power (CSP) projects, thereby accelerating the commercial deployment of this new power generation technology. The project involved eight partnering organizations: NREL, Sandia National Laboratories, Echogen Power Systems, Abengoa Solar, University of Wisconsin at Madison, Electric Power Research Institute, Barber-Nichols, and the CSP Program of the U.S. Department of Energy. The multi-year project planned to design, fabricate, and validate an s-CO2 power turbine of nominally 10 MWe that is capable of operation at up to 700°C and operates in a dry-cooled test loop. The project plan consisted of three phases: (1) system design and modeling, (2) fabrication, and (3) testing. The major accomplishments of Phase 1 included: Design of a multistage, axial-flow, s-CO2 power turbine; Design modifications to an existing turbocompressor to provide s-CO2 flow for the test system; Updated equipment and installation costs for the turbomachinery and associated support infrastructure; Development of simulation tools for the test loop itself and for more efficient cycle designs that are of greater commercial interest; Simulation of s-CO2 power cycle integration into molten-nitrate-salt CSP systems indicating a cost benefit of up to 8% in levelized cost of energy; Identification of recuperator cost as a key economic parameter; Corrosion data for multiple alloys at temperatures up to 650ºC in high-pressure CO2 and recommendations for materials-of-construction; and Revised test plan and preliminary operating conditions based on the ongoing tests of related equipment. Phase 1 established that the cost of the facility needed to test the power turbine at its full power and temperature would exceed the planned funding for Phases 2 and 3. Late

χ_{c1} and χ_{c2} Resonance Parameters with the Decays χ_{c1,c2}→J/ψμ^{+}μ^{-}.

Science.gov (United States)

Aaij, R; Adeva, B; Adinolfi, M; Ajaltouni, Z; Akar, S; Albrecht, J; Alessio, F; Alexander, M; Alfonso Albero, A; Ali, S; Alkhazov, G; Alvarez Cartelle, P; Alves, A A; Amato, S; Amerio, S; Amhis, Y; An, L; Anderlini, L; Andreassi, G; Andreotti, M; Andrews, J E; Appleby, R B; Archilli, F; d'Argent, P; Arnau Romeu, J; Artamonov, A; Artuso, M; Aslanides, E; Atzeni, M; Auriemma, G; Baalouch, M; Babuschkin, I; Bachmann, S; Back, J J; Badalov, A; Baesso, C; Baker, S; Balagura, V; Baldini, W; Baranov, A; Barlow, R J; Barschel, C; Barsuk, S; Barter, W; Baryshnikov, F; Batozskaya, V; Battista, V; Bay, A; Beaucourt, L; Beddow, J; Bedeschi, F; Bediaga, I; Beiter, A; Bel, L J; Beliy, N; Bellee, V; Belloli, N; Belous, K; Belyaev, I; Ben-Haim, E; Bencivenni, G; Benson, S; Beranek, S; Berezhnoy, A; Bernet, R; Berninghoff, D; Bertholet, E; Bertolin, A; Betancourt, C; Betti, F; Bettler, M-O; van Beuzekom, M; Bezshyiko, Ia; Bifani, S; Billoir, P; Birnkraut, A; Bizzeti, A; Bjørn, M; Blake, T; Blanc, F; Blusk, S; Bocci, V; Boettcher, T; Bondar, A; Bondar, N; Bordyuzhin, I; Borghi, S; Borisyak, M; Borsato, M; Bossu, F; Boubdir, M; Bowcock, T J V; Bowen, E; Bozzi, C; Braun, S; Britton, T; Brodzicka, J; Brundu, D; Buchanan, E; Burr, C; Bursche, A; Buytaert, J; Byczynski, W; Cadeddu, S; Cai, H; Calabrese, R; Calladine, R; Calvi, M; Calvo Gomez, M; Camboni, A; Campana, P; Campora Perez, D H; Capriotti, L; Carbone, A; Carboni, G; Cardinale, R; Cardini, A; Carniti, P; Carson, L; Carvalho Akiba, K; Casse, G; Cassina, L; Cattaneo, M; Cavallero, G; Cenci, R; Chamont, D; Chapman, M G; Charles, M; Charpentier, Ph; Chatzikonstantinidis, G; Chefdeville, M; Chen, S; Cheung, S F; Chitic, S-G; Chobanova, V; Chrzaszcz, M; Chubykin, A; Ciambrone, P; Cid Vidal, X; Ciezarek, G; Clarke, P E L; Clemencic, M; Cliff, H V; Closier, J; Cogan, J; Cogneras, E; Cogoni, V; Cojocariu, L; Collins, P; Colombo, T; Comerma-Montells, A; Contu, A; Cook, A; Coombs, G; Coquereau, S; Corti, G; Corvo, M; Costa Sobral, C M; Couturier, B; Cowan, G A; Craik, D C; Crocombe, A; Cruz Torres, M; Currie, R; D'Ambrosio, C; Da Cunha Marinho, F; Dall'Occo, E; Dalseno, J; Davis, A; De Aguiar Francisco, O; De Capua, S; De Cian, M; De Miranda, J M; De Paula, L; De Serio, M; De Simone, P; Dean, C T; Decamp, D; Del Buono, L; Dembinski, H-P; Demmer, M; Dendek, A; Derkach, D; Deschamps, O; Dettori, F; Dey, B; Di Canto, A; Di Nezza, P; Dijkstra, H; Dordei, F; Dorigo, M; Dosil Suárez, A; Douglas, L; Dovbnya, A; Dreimanis, K; Dufour, L; Dujany, G; Durante, P; Dzhelyadin, R; Dziewiecki, M; Dziurda, A; Dzyuba, A; Easo, S; Ebert, M; Egede, U; Egorychev, V; Eidelman, S; Eisenhardt, S; Eitschberger, U; Ekelhof, R; Eklund, L; Ely, S; Esen, S; Evans, H M; Evans, T; Falabella, A; Farley, N; Farry, S; Fazzini, D; Federici, L; Ferguson, D; Fernandez, G; Fernandez Declara, P; Fernandez Prieto, A; Ferrari, F; Ferreira Rodrigues, F; Ferro-Luzzi, M; Filippov, S; Fini, R A; Fiorini, M; Firlej, M; Fitzpatrick, C; Fiutowski, T; Fleuret, F; Fohl, K; Fontana, M; Fontanelli, F; Forshaw, D C; Forty, R; Franco Lima, V; Frank, M; Frei, C; Fu, J; Funk, W; Furfaro, E; Färber, C; Gabriel, E; Gallas Torreira, A; Galli, D; Gallorini, S; Gambetta, S; Gandelman, M; Gandini, P; Gao, Y; Garcia Martin, L M; García Pardiñas, J; Garra Tico, J; Garrido, L; Garsed, P J; Gascon, D; Gaspar, C; Gavardi, L; Gazzoni, G; Gerick, D; Gersabeck, E; Gersabeck, M; Gershon, T; Ghez, Ph; Gianì, S; Gibson, V; Girard, O G; Giubega, L; Gizdov, K; Gligorov, V V; Golubkov, D; Golutvin, A; Gomes, A; Gorelov, I V; Gotti, C; Govorkova, E; Grabowski, J P; Graciani Diaz, R; Granado Cardoso, L A; Graugés, E; Graverini, E; Graziani, G; Grecu, A; Greim, R; Griffith, P; Grillo, L; Gruber, L; Gruberg Cazon, B R; Grünberg, O; Gushchin, E; Guz, Yu; Gys, T; Göbel, C; Hadavizadeh, T; Hadjivasiliou, C; Haefeli, G; Haen, C; Haines, S C; Hamilton, B; Han, X; Hancock, T H; Hansmann-Menzemer, S; Harnew, N; Harnew, S T; Hasse, C; Hatch, M; He, J; Hecker, M; Heinicke, K; Heister, A; Hennessy, K; Henrard, P; Henry, L; van Herwijnen, E; Heß, M; Hicheur, A; Hill, D; Hombach, C; Hopchev, P H; Hu, W; Huard, Z C; Hulsbergen, W; Humair, T; Hushchyn, M; Hutchcroft, D; Ibis, P; Idzik, M; Ilten, P; Jacobsson, R; Jalocha, J; Jans, E; Jawahery, A; Jiang, F; John, M; Johnson, D; Jones, C R; Joram, C; Jost, B; Jurik, N; Kandybei, S; Karacson, M; Kariuki, J M; Karodia, S; Kazeev, N; Kecke, M; Keizer, F; Kelsey, M; Kenzie, M; Ketel, T; Khairullin, E; Khanji, B; Khurewathanakul, C; Kirn, T; Klaver, S; Klimaszewski, K; Klimkovich, T; Koliiev, S; Kolpin, M; Kopecna, R; Koppenburg, P; Kosmyntseva, A; Kotriakhova, S; Kozeiha, M; Kravchuk, L; Kreps, M; Kress, F; Krokovny, P; Kruse, F; Krzemien, W; Kucewicz, W; Kucharczyk, M; Kudryavtsev, V; Kuonen, A K; Kvaratskheliya, T; Lacarrere, D; Lafferty, G; Lai, A; Lanfranchi, G; Langenbruch, C; Latham, T; Lazzeroni, C; Le Gac, R; Leflat, A; Lefrançois, J; Lefèvre, R; Lemaitre, F; Lemos Cid, E; Leroy, O; Lesiak, T; Leverington, B; Li, P-R; Li, T; Li, Y; Li, Z; Likhomanenko, T; Lindner, R; Lionetto, F; Lisovskyi, V; Liu, X; Loh, D; Loi, A; Longstaff, I; Lopes, J H; Lucchesi, D; Luchinsky, A; Lucio Martinez, M; Luo, H; Lupato, A; Luppi, E; Lupton, O; Lusiani, A; Lyu, X; Machefert, F; Maciuc, F; Macko, V; Mackowiak, P; Maddrell-Mander, S; Maev, O; Maguire, K; Maisuzenko, D; Majewski, M W; Malde, S; Malecki, B; Malinin, A; Maltsev, T; Manca, G; Mancinelli, G; Marangotto, D; Maratas, J; Marchand, J F; Marconi, U; Marin Benito, C; Marinangeli, M; Marino, P; Marks, J; Martellotti, G; Martin, M; Martinelli, M; Martinez Santos, D; Martinez Vidal, F; Massacrier, L M; Massafferri, A; Matev, R; Mathad, A; Mathe, Z; Matteuzzi, C; Mauri, A; Maurice, E; Maurin, B; Mazurov, A; McCann, M; McNab, A; McNulty, R; Mead, J V; Meadows, B; Meaux, C; Meier, F; Meinert, N; Melnychuk, D; Merk, M; Merli, A; Michielin, E; Milanes, D A; Millard, E; Minard, M-N; Minzoni, L; Mitzel, D S; Mogini, A; Molina Rodriguez, J; Mombächer, T; Monroy, I A; Monteil, S; Morandin, M; Morello, M J; Morgunova, O; Moron, J; Morris, A B; Mountain, R; Muheim, F; Mulder, M; Müller, D; Müller, J; Müller, K; Müller, V; Naik, P; Nakada, T; Nandakumar, R; Nandi, A; Nasteva, I; Needham, M; Neri, N; Neubert, S; Neufeld, N; Neuner, M; Nguyen, T D; Nguyen-Mau, C; Nieswand, S; Niet, R; Nikitin, N; Nikodem, T; Nogay, A; O'Hanlon, D P; Oblakowska-Mucha, A; Obraztsov, V; Ogilvy, S; Oldeman, R; Onderwater, C J G; Ossowska, A; Otalora Goicochea, J M; Owen, P; Oyanguren, A; Pais, P R; Palano, A; Palutan, M; Papanestis, A; Pappagallo, M; Pappalardo, L L; Parker, W; Parkes, C; Passaleva, G; Pastore, A; Patel, M; Patrignani, C; Pearce, A; Pellegrino, A; Penso, G; Pepe Altarelli, M; Perazzini, S; Perret, P; Pescatore, L; Petridis, K; Petrolini, A; Petrov, A; Petruzzo, M; Picatoste Olloqui, E; Pietrzyk, B; Pikies, M; Pinci, D; Pisani, F; Pistone, A; Piucci, A; Placinta, V; Playfer, S; Plo Casasus, M; Polci, F; Poli Lener, M; Poluektov, A; Polyakov, I; Polycarpo, E; Pomery, G J; Ponce, S; Popov, A; Popov, D; Poslavskii, S; Potterat, C; Price, E; Prisciandaro, J; Prouve, C; Pugatch, V; Puig Navarro, A; Pullen, H; Punzi, G; Qian, W; Quagliani, R; Quintana, B; Rachwal, B; Rademacker, J H; Rama, M; Ramos Pernas, M; Rangel, M S; Raniuk, I; Ratnikov, F; Raven, G; Ravonel Salzgeber, M; Reboud, M; Redi, F; Reichert, S; Dos Reis, A C; Remon Alepuz, C; Renaudin, V; Ricciardi, S; Richards, S; Rihl, M; Rinnert, K; Rives Molina, V; Robbe, P; Robert, A; Rodrigues, A B; Rodrigues, E; Rodriguez Lopez, J A; Rogozhnikov, A; Roiser, S; Rollings, A; Romanovskiy, V; Romero Vidal, A; Ronayne, J W; Rotondo, M; Rudolph, M S; Ruf, T; Ruiz Valls, P; Ruiz Vidal, J; Saborido Silva, J J; Sadykhov, E; Sagidova, N; Saitta, B; Salustino Guimaraes, V; Sanchez Mayordomo, C; Sanmartin Sedes, B; Santacesaria, R; Santamarina Rios, C; Santimaria, M; Santovetti, E; Sarpis, G; Sarti, A; Satriano, C; Satta, A; Saunders, D M; Savrina, D; Schael, S; Schellenberg, M; Schiller, M; Schindler, H; Schmelling, M; Schmelzer, T; Schmidt, B; Schneider, O; Schopper, A; Schreiner, H F; Schubiger, M; Schune, M-H; Schwemmer, R; Sciascia, B; Sciubba, A; Semennikov, A; Sepulveda, E S; Sergi, A; Serra, N; Serrano, J; Sestini, L; Seyfert, P; Shapkin, M; Shapoval, I; Shcheglov, Y; Shears, T; Shekhtman, L; Shevchenko, V; Siddi, B G; Silva Coutinho, R; Silva de Oliveira, L; Simi, G; Simone, S; Sirendi, M; Skidmore, N; Skwarnicki, T; Smith, E; Smith, I T; Smith, J; Smith, M; Soares Lavra, L; Sokoloff, M D; Soler, F J P; Souza De Paula, B; Spaan, B; Spradlin, P; Sridharan, S; Stagni, F; Stahl, M; Stahl, S; Stefko, P; Stefkova, S; Steinkamp, O; Stemmle, S; Stenyakin, O; Stepanova, M; Stevens, H; Stone, S; Storaci, B; Stracka, S; Stramaglia, M E; Straticiuc, M; Straumann, U; Sun, J; Sun, L; Sutcliffe, W; Swientek, K; Syropoulos, V; Szumlak, T; Szymanski, M; T'Jampens, S; Tayduganov, A; Tekampe, T; Tellarini, G; Teubert, F; Thomas, E; van Tilburg, J; Tilley, M J; Tisserand, V; Tobin, M; Tolk, S; Tomassetti, L; Tonelli, D; Toriello, F; Tourinho Jadallah Aoude, R; Tournefier, E; Traill, M; Tran, M T; Tresch, M; Trisovic, A; Tsaregorodtsev, A; Tsopelas, P; Tully, A; Tuning, N; Ukleja, A; Usachov, A; Ustyuzhanin, A; Uwer, U; Vacca, C; Vagner, A; Vagnoni, V; Valassi, A; Valat, S; Valenti, G; Vazquez Gomez, R; Vazquez Regueiro, P; Vecchi, S; van Veghel, M; Velthuis, J J; Veltri, M; Veneziano, G; Venkateswaran, A; Verlage, T A; Vernet, M; Vesterinen, M; Viana Barbosa, J V; Viaud, B; Vieira, D; Vieites Diaz, M; Viemann, H; Vilasis-Cardona, X; Vitti, M; Volkov, V; Vollhardt, A; Voneki, B; Vorobyev, A; Vorobyev, V; Voß, C; de Vries, J A; Vázquez Sierra, C; Waldi, R; Wallace, C; Wallace, R; Walsh, J; Wang, J; Ward, D R; Wark, H M; Watson, N K; Websdale, D; Weiden, A; Weisser, C; Whitehead, M; Wicht, J; Wilkinson, G; Wilkinson, M; Williams, M; Williams, M P; Williams, M; Williams, T; Wilson, F F; Wimberley, J; Winn, M; Wishahi, J; Wislicki, W; Witek, M; Wormser, G; Wotton, S A; Wraight, K; Wyllie, K; Xie, Y; Xu, M; Xu, Z; Yang, Z; Yang, Z; Yao, Y; Yin, H; Yu, J; Yuan, X; Yushchenko, O; Zarebski, K A; Zavertyaev, M; Zhang, L; Zhang, Y; Zhelezov, A; Zheng, Y; Zhu, X; Zhukov, V; Zonneveld, J B; Zucchelli, S

2017-12-01

The decays χ_{c1}→J/ψμ^{+}μ^{-} and χ_{c2}→J/ψμ^{+}μ^{-} are observed and used to study the resonance parameters of the χ_{c1} and χ_{c2} mesons. The masses of these states are measured to be m(χ_{c1})=3510.71±0.04(stat)±0.09(syst)  MeV and m(χ_{c2})=3556.10±0.06(stat)±0.11(syst)  MeV, where the knowledge of the momentum scale for charged particles dominates the systematic uncertainty. The momentum-scale uncertainties largely cancel in the mass difference m(χ_{c2})-m(χ_{c1})=45.39±0.07(stat)±0.03(syst)  MeV. The natural width of the χ_{c2} meson is measured to be Γ(χ_{c2})=2.10±0.20(stat)±0.02(syst)  MeV. These results are in good agreement with and have comparable precision to the current world averages.

Fracture testing and performance of beryllium copper alloy C 17510

International Nuclear Information System (INIS)

Murray, H.A.; Zatz, I.J.

1992-01-01

A series of test programs was undertaken on copper beryllium alloy C 17510 for several variations in material process and chemistry. These variations in C 17510 were primarily optimized for combinations of strength and conductivity. While originally intended for use as cyclically loaded high-field, high-strength conductors in fusion energy research, material testing of C 17510 has indicated that it is an attractive and economical alternative for a host of other structural, mechanical and electrical applications. ASTM tests performed on three variations of C 17510 alloys included both J-integral and plane strain fracture toughness testing (E813, E399) and fatigue crack growth rate tests (E647), as well as verifying tensile, hardness, Charpy, and other well defined mechanical properties. Fracture testing was performed at both room and liquid nitrogen temperatures, which bound the thermal environment anticipated for the fusion components being designed. Fatigue crack propagation stress ratios ranged from nominal zero to minus one at each temperature

SiC Nanoparticles Toughened-SiC/MoSi2-SiC Multilayer Functionally Graded Oxidation Protective Coating for Carbon Materials at High Temperatures

Science.gov (United States)

Abdollahi, Alireza; Ehsani, Naser; Valefi, Zia; Khalifesoltani, Ali

2017-05-01

A SiC nanoparticle toughened-SiC/MoSi2-SiC functionally graded oxidation protective coating on graphite was prepared by reactive melt infiltration (RMI) at 1773 and 1873 K under argon atmosphere. The phase composition and anti-oxidation behavior of the coatings were investigated. The results show that the coating was composed of MoSi2, α-SiC and β-SiC. By the variations of Gibbs free energy (calculated by HSC Chemistry 6.0 software), it could be suggested that the SiC coating formed at low temperatures by solution-reprecipitation mechanism and at high temperatures by gas-phase reactions and solution-reprecipitation mechanisms simultaneously. SiC nanoparticles could improve the oxidation resistance of SiC/MoSi2-SiC multiphase coating. Addition of SiC nanoparticles increases toughness of the coating and prevents spreading of the oxygen diffusion channels in the coating during the oxidation test. The mass loss and oxidation rate of the SiC nanoparticle toughened-SiC/MoSi2-SiC-coated sample after 10-h oxidation at 1773 K were only 1.76% and 0.32 × 10-2 g/cm3/h, respectively.

13C mixed triglyceride breath test: a noninvasive method to assess lipase activity in children.

Science.gov (United States)

van Dijk-van Aalst, K; Van Den Driessche, M; van Der Schoor, S; Schiffelers, S; van't Westeinde, T; Ghoos, Y; Veereman-Wauters, G

2001-05-01

Results from the 13C mixed triglyceride (MTG) breath test correlate with duodenal lipase activity in adults. This noninvasive test is a potential screening and diagnostic tool for children with fat malabsorption. The aim of this study was to adapt the methodology of the MTG breath test to study test meals and sampling methods and to define normal values for healthy children of all age groups; premature and full-term infants have similar pancreatic lipase deficiencies. After parental consent was obtained, 12 premature infants ( 2 kg), 12 full-term infants (1-6 months old), 20 children (3-10 years old), and 20 teenagers (11-17 years old) were tested. All children were thriving well, had no gastrointestinal or respiratory problems, and had not received any medication that contained natural 13C. For the premature and full-term infants, a formula was prepared that had a low and stable natural 13C content mixed with 100 mg 13C-labeled MTG (1,3-distearyl, 2-[13C-carboxyl] octanoyl glycerol) and 1 g polyethylene-glycol 3350. The best accepted test meal for children over 3 years old was a slice of white bread with 5 g butter and 15 g chocolate paste, mixed with 250 mg 13C-labeled MTG, and a glass of 100 mL whole-fat milk. Children over 3 years old were able to blow through a straw in a vacutainer for collecting the breath samples. In children under 3 years old, expired air was collected by aspirating breath via a nasal prong. Carbon dioxide production was calculated according to weight, age, and sex. For healthy pediatric control participants, the mean values for cumulative excretion of 13CO2 as a percentage of the administered dose after 6 hours were 23.9 +/- 5.2% in premature infants, 31.9 +/- 7.7% in full-term infants, 32.5 +/- 5.3% in children, and 28.0 +/- 5.4% in teenagers. The mean value for healthy adults is 35.6% with a lower reference limit of 22.8%. Age-specific test meals and breath-sampling techniques for the MTG breath test were defined. The mean values for

Synthetic of Zr2Al3C5 material

International Nuclear Information System (INIS)

Leela-Adisorn, U.; Yamaguchi, A.

2005-01-01

Synthesis method of Zr 2 Al 3 C 5 via solid state reaction between Al, ZrC and carbon powder was studied. Al-ZrC-C compact with equivalent mol ratio of Zr 2 Al 3 C 5 was heated up to 1600 C in Ar atmosphere for 1 h and 4 h but ZrC phase still existed as major phase with very small amount of Zr 2 Al 3 C 5 . Because ZrC started to oxidize at low temperature under very low oxygen partial pressure, the same mol ratio of Al-ZrC-C compact was heated at 1600 C in vacuum for 1 h as parallel test. After firing in vacuum, some carbon still exist with small amount of AlZrC 2 occurred with Zr 2 Al 3 C 5 as a main phase, but no ZrC was found. Different result from firing in Ar atmosphere and in vacuum had been discussed here. It was believed that very small amount of impurities in Ar had some effect on the formation of Al-Zr-C compound. The effect of very small amount of impurities in Ar was studied by thermal analysis (DTA/TG) and XRD. It was found that very small amount of impurities in Ar has effect on the reaction between Al, ZrC and carbon by diffusion through the surface and form Zr-C-O-N solid solution. This solid solution cannot differentiate from ZrC by XRD. With help of thermal analysis method (DTA/TG), Zr-C-O-N solid solution can be differentiated from ZrC. Therefore, synthesis of Al-Zr-C compound should be done in vacuum. Zr 2 Al 3 C 5 can be prepared from mixture of Al-ZrC-C with excess amount of Al at 1600 C for 1 h. (orig.)

Evaluation report on CCTF Core-II reflood test second shakedown test, C2-SH2 (Run 54)

International Nuclear Information System (INIS)

Iguchi, Tadashi; Sugimoto, Jun; Akimoto, Hajime; Okubo, Tsutomu; Murao, Yoshio

1985-03-01

A low power test (the initial averaged linear power density = 1.18 kW/m) and the base case test (1.4 kW/m) were performed with the Cylindrical Core Test Facility (CCTF) at Japan Atomic Energy Research Institute, in order to study the effect of the power on the reflood phenomena. The former linear power density corresponds nearly to the scaled linear power density based on the current safety evaluation criterio. During the early period of the reflood ( 200s) the heat transfer coefficient became higher and resultantly the quench front advanced faster in the low power test. The core flooding rate was nearly identical between both tests, independently of the different power. The insensitiveness of the power to the core flooding rate was also observed in FLECHT-SET performed in the USA. A significatn large differential pressure oscillation at ECC ports was experienced in the low power test, and it may be important for the long term core cooling although it has not been taken note on the previous studies. (author)

75 FR 10026 - Proposed Collection; Comment Request for Forms W-2, W-2c, W-2AS, W-2GU, W-2VI, W-3, W-3c, W-3cPR...

Science.gov (United States)

2010-03-04

... W-2, W-2c, W-2AS, W-2GU, W-2VI, W-3, W-3c, W-3cPR, W-3PR, and W-3SS AGENCY: Internal Revenue Service....C. 3506(c)(2)(A)). Currently, the IRS is soliciting comments concerning Forms W-2, W-2c, W-2AS, W-2GU, W-2VI, W-3, W-3c, W- 3cPR, W-3PR, and W-3SS. DATES: Written comments should be received on or...

Evaluation report on CCTF Core-II reflood test C2-1 (Run 55)

International Nuclear Information System (INIS)

Iguchi, Tadashi; Sugimoto, Jun; Akimoto, Hajime; Okubo, Tsutomu; Murao, Yoshio

1991-10-01

A high pressure test (0.42 MPa) on the reflood phenomena was performed with the CCTF. The result of the test was compared with the experimental result of the base case test (0.2 MPa). (1) The overall flow characteristics in the high pressure test were qualitatively similar to that of the base case test. Any qualitatively different phenomena were not recognized during reflood phase. This indicates that it is reasonable to utilize the physical reflood model developed from the result of the base case test to the high pressure condition at least up to 0.42 MPa for prediction of reflood behavior of PWRs. (2) On the other hand, following quantitative influence of high pressure on reflood phenomena was observed. The core cooling was better, and the mass flow rate of the steam generated in the core was larger. However, the steam velocity was smaller due to higher density of the steam. Therefore, the steam discharge through loops was easier and hence the so-called steam binding effect was weaker. And, the water accumulation rate in the core was larger. Consequently the core flooding mass flow rate was larger. Since the core cooling was better, the maximum core temperature was lower and the last quenching was earlier. This result was the same as that previously observed in CCTF tests in the scope of the pressure upto 0.3 MPa. (3) The higher pressure leads to the better core cooling, and hence the safety margin increases with the increase in the pressure. (author)

The 14C-urea breath-test for the detection of gastric Campylobacter pylori infection

International Nuclear Information System (INIS)

Surveyor, I.; Goodwin, C.S.; Mullan, B.P.; Geelhoed, E.; Warren, J.R.; Murray, R.N.; Waters, T.E.; Sanderson, C.R.

1989-01-01

Sixty-three patients who were undergoing endoscopy were studied. The radioactivity in exhaled breath which was sampled within five minutes of 14 C -urea administration was attributed to the presence of urease enzyme in mouth organisms and was discounted. The time-radioactivity curves for breath samples from five to 30 minutes after the administration of 14 C-urea gave an excellent separation between subjects with negative results of the examination of gastric-biopsy samples and patients with microbiological and histological evidence of infection with Campylobacter (C.) pylori. The area under the time-radioactivity curve at between five and 30 minutes after the administration of 14 C-urea in 24 patients with negative microbiological results was 6.9±4.4 area units; in 35 of 39 patients with positive microbiological results, this area was greater than 40 area units. Measured against the results of the microbiological examination of gastricbiopsy samples, the sensitivity of breath-testing was 90% and the specificity was 100%. Measured against the results of histological examination for the presence of C. pylori infection, breath-testing had a sensitivity of 94% and a specificity of 93%. A positive breath-test result also correlated well (P=0.0001) with the serological antibody test-result. The role of non-invasive tests - enzyme-linked immunosorbent assays and 14 C-urea breath-testing - in the management of gastritis and peptic ulcer disease is discussed. We consider that the 14 C-urea breath-test has an important role in the noninvasive confirmation of gastric infection with C. pylori and in the follow-up of patients after treatment. 38 refs., 2 figs., 1 tab

Appraisal of the /sup 14/C-glycocholate acid test with special reference to the measurement of faecal /sup 14/C excretion

Energy Technology Data Exchange (ETDEWEB)

Scarpello, J H.B.; Sladen, G E [Royal Hospital, Sheffield (UK). Academic Div. of Medicine

1977-09-01

The /sup 14/C-glycocholate test, including the measurement of marker corrected faecal /sup 14/C, has been assessed in the following groups of subjects: normal controls (18), patients with diarrhoea not attributable to altered bile acid metabolism (21), patients with diverticula of the small intestine (12), patients with previous resection of ileum and often proximal colon (34), and established ileostomists (10). Patients with diverticular disease had increased breath /sup 14/CO/sub 2/ excretion, but normal faecal excretion of /sup 14/C, and this test was more frequently abnormal than the Schilling test. Ileostomists excreted increased amounts of faecal /sup 14/C, even when the ileum was intact and apparently normal. The pattern after resection was complex. Breath /sup 14/C output was normal if the ileal resection was less than 25 cm in length, although some of these patients had increased faecal /sup 14/C excretion if, in addition, at least 15 cm of proximal colon had been resected or by-passed. Longer ileal resections were associated with increased breath and/or faecal /sup 14/C excretion, depending in part on the length of colon resected or by-passed and the 24 hour faecal volume. Fewer than half these patients had both increased breath and faecal excretion of isotope and faecal /sup 14/C alone was occasionally normal with an ileal resection of 50 cm or more. The /sup 14/C-glycocholate test was more frequently abnormal than the Schilling test in this group. The use of faecal marker correction had only a minor impact on the results. These data suggest that, in patients with ileal resection, faecal /sup 14/C, like faecal weight, is determined by the extent of colonic resection as well as by the amount of ileum resected.

Applications of the nuclear Techniques in medicine: 13C or 14C respiration tests

International Nuclear Information System (INIS)

Rivero Santamaria, Alejandro

2008-01-01

The 14 C or 13 C respiration tests have been applied to the study of metabolic and infectious processes, but most of them have not entered yet the clinical practice stage. In this paper, it is offered an overview of the present and future of respiration tests and how they are taking part and will take part in a future in the non-invasive diagnosis of diverse pathologies

Preparation and characterization of Pt–CeO{sub 2}/C and Pt–TiO{sub 2}/C electrocatalysts with improved electrocatalytic activity for methanol oxidation

Energy Technology Data Exchange (ETDEWEB)

Hameed, R.M. Abdel [Chemistry Department, Faculty of Science, Cairo University, Giza (Egypt); Amin, R.S. [Chemical Engineering Department, National Research Center, Dokki, Giza (Egypt); El-Khatib, K.M., E-mail: Kamelced@hotmail.com [Chemical Engineering Department, National Research Center, Dokki, Giza (Egypt); Fetohi, Amani E. [Chemical Engineering Department, National Research Center, Dokki, Giza (Egypt)

2016-03-30

Graphical abstract: - Highlights: • Adding TiO{sub 2} or CeO{sub 2} to Pt/C reduced its Pt particle size. • Methanol oxidation current density decreased as Pt–CeO{sub 2}/C > Pt–TiO{sub 2}/C > Pt/C. • Decreased R{sub ct} values were observed at Pt–TiO{sub 2}/C and Pt–CeO{sub 2}/C. - Abstract: Pt–TiO{sub 2}/C and Pt–CeO{sub 2}/C electrocatalysts were synthesized by solid state reaction of TiO{sub 2}/C and CeO{sub 2}/C powders using intermittent microwave heating, followed by chemical reduction of platinum ions using mixed reducing agents of ethylene glycol and sodium borohydride. The crystal structure, surface morphology and chemical composition of prepared electrocatalysts were investigated using X-ray diffraction (XRD), transmission electron microscopy (TEM) and energy dispersive X-ray analysis (EDX). The phase angle values of different Pt diffraction planes in Pt–TiO{sub 2}/C and Pt–CeO{sub 2}/C were shifted in the positive direction relative to those in Pt/C. Pt particles with diameter values of 3.06 and 2.78 nm were formed in Pt–TiO{sub 2}/C and Pt–CeO{sub 2}/C, respectively. The electrochemical performance of prepared electrocatalysts was examined using cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy. Pt–CeO{sub 2}/C showed an enhanced oxidation current density when compared to Pt/C. Long time oxidation test at Pt–TiO{sub 2}/C and Pt–CeO{sub 2}/C revealed their improved stability. Lower charge transfer resistance values were estimated at Pt–metal oxide/C electrocatalysts.

In-situ fabrication of MoSi2/SiC–Mo2C gradient anti-oxidation coating on Mo substrate and the crucial effect of Mo2C barrier layer at high temperature

International Nuclear Information System (INIS)

Liu, Jun; Gong, Qianming; Shao, Yang; Zhuang, Daming; Liang, Ji

2014-01-01

MoSi 2 /SiC–Mo 2 C gradient coating on molybdenum was in situ prepared with pack cementation process by two steps: (1) carburizing with graphite powder to obtain a Mo 2 C layer on Mo substrate, and (2) siliconizing with Si powder to get a composite MoSi 2 /SiC layer on the upper part of Mo 2 C layer. The microstructure and elemental distribution in the coating were investigated with scanning electron microscopy (SEM), backscattered electron (BSE), energy dispersive spectroscopy (EDS), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). Cyclic oxidation tests (at 500 °C, 1200 °C, 1400 °C and 1600 °C) demonstrated excellent oxidation resistance for the gradient composite coating and the mass loss was only 0.23% in 60 min at 1600 °C. XRD, EPMA, thermal dynamic and phase diagram analyses indicated that the Mo 2 C barrier layer played the key role in slowing down the diffusion of C and Si toward inner Mo substrate at high temperature and principally this contributed to the excellent anti-oxidation for Mo besides the outer MoSi 2 /SiC composite layer.

Effect of curcumin Extract on Ttranslocation of Glut 4 in C2C12 Myotubes

Directory of Open Access Journals (Sweden)

J Zavarreza

2013-06-01

Full Text Available Introduction: Curcumin is a major phenolic compound of Curcuma longa, which has long been used in traditional Indian medicine. Recently, curcumin has been reported to have antihyperglycemic activity in animal models. However, the molecular basis of this action has not been adequatedly described. In the present study the antihyperglycemic effect of curcumin was examined using C2C12 myoblast cells. Methods: The effects of curcumin were investigated in C2C12 myotubes by treating the cells with 40 µM of curcumin for 1.5 h. C2C12 myotubes were homogenized and the subcellular fractionation was prepared using ultracentrifugation; Then protein assay was performed using Bradford method and Glut4 determination was done using SDS-PAGE. Moreover, western immunoblotting techniques were exerted for semi-quantitative measurement. Data analysis was performed via gene tools software of Gel documentation and SPSS. An ANOVA test was used to compare three groups together. Results: Comparison of Glut4 levels in C2C12 myotubes showed that myotubes which were exposed to1.5 hours of 40 µM curcunin had higher Glut4 percentages in both cytosolic and membrane fractions and Glut4 percentages were significant with a confidence interval (CI of 95% ( P<0.05 . Conclusion: The study results showed that curcumin can strongly induce the increase of Glut4 translocation in differentiated C2C12 cells, indicating its possible regulatory role in the glucose metabolism of skeletal muscle cells

properties of Cr(C,N) hard coatings deposited in Ar-C2H2-N2 plasma

International Nuclear Information System (INIS)

Macek, M.; Cekada, M.; Kek, D.; Panjan, P.

2002-01-01

Mechanical properties, microstructure and the average chemical composition of Cr(C,N) hard coatings deposited in Ar-C 2 H 2 -N 2 plasma strongly depends on the partial pressure of the reactive gases (N 2 , C 2 H 2 ) and on the type of the deposition equipment. In this study we report on the properties of Cr(C,N) hard coatings deposited by means of the triode ion plating in the BAI 730 apparatus and those prepared by sputter deposition in Balzers Sputron in the pressure range from 0.12 Pa (pure Ar) up to 0.35 Pa with different ratios (0-100%) between C 2 H 2 and N 2 . At first mechanical properties (microhardness and adhesion) of coatings were analyzed on the common way. Internal stress was measured by the radius of substrate curvature. Chemical composition of coatings was analyzed by means of AES while the Raman and XPS spectroscopy was used to determined the nature of carbon bonding in the Cr(C,N) films. Microstructure was determined by XRD as well as by means of TEM and TED. Chemical state of various elements in the coating has been studied by XPS. The ratio of the carbide bond (C-Cr) against the C-C and C-H bonds was calculated. The existence of the graphite phase in some Cr(C,N) coatings was confirmed by Raman spectroscopy. (Authors)

IMPACT2C: Quantifying projected impacts under 2°C warming

Science.gov (United States)

Jacob, D.; Kotova, L.; Impact2C Team

2012-04-01

Political discussions on the European goal to limit global warming to 2°C demand, that information is provided to society by the best available science on projected impacts and possible benefits. The new project IMPACT2C is supported by the European Commission's 7th Framework Programme as a 4 year large-scale integrating project. IMPACT2C is coordinated by the Climate Service Center, Helmholtz-Zentrum Geesthacht. IMPACT2C enhances knowledge, quantifies climate change impacts, and adopts a clear and logical structure, with climate and impacts modelling, vulnerabilities, risks and economic costs, as well as potential responses, within a pan-European sector based analysis. The project utilises a range of models within a multi-disciplinary international expert team and assesses effects on water, energy, infrastructure, coasts, tourism, forestry, agriculture, ecosystems services, and health and air quality-climate interactions. IMPACT2C introduces key innovations. First, harmonised socio-economic assumptions/scenarios will be used, to ensure that both individual and cross-sector assessments are aligned to the 2°C (1.5°C) scenario for both impacts and adaptation, e.g. in relation to land-use pressures between agriculture and forestry. Second, it has a core theme of uncertainty, and will develop a methodological framework integrating the uncertainties within and across the different sectors, in a consistent way. In so doing, analysis of adaptation responses under uncertainty will be enhanced. Finally, a cross-sectoral perspective is adopted to complement the sector analysis. A number of case studies will be developed for particularly vulnerable areas, subject to multiple impacts (e.g. the Mediterranean), with the focus being on cross-sectoral interactions (e.g. land use competition) and cross-cutting themes (e.g. cities). The project also assesses climate change impacts in some of the world's most vulnerable regions: Bangladesh, Africa (Nile and Niger basins), and the

Oxidation of UO2 at 150 to 3500C

International Nuclear Information System (INIS)

Gilbert, E.R.; White, G.D.; Knox, C.A.

1985-02-01

Tests were performed on nonirradiated UO 2 pellets from 150 to 350 0 C in atmospheric air and controlled environments and on spent light-water reactor (LWR) fuel fragments at 200 and 230 0 C in atmospheric air to determine the variables that affect oxidation behavior under dry storage conditions. The weight of spent fragments increased 50 to 100 times faster than the weight of nonirradiated UO 2 pellets at 230 0 C. Non-irradiated pellet fragments gained weight 5 to 7 times faster than nonirradiated pellets. The fragments simulated fuel fragmented by thermal gradients during reactor power changes. Low-density powder (U 3 O 8 ) formed at 0.05 and 0.3% weight gain for nonirradiated pellets and fragments, respectively, but had not formed at 3% weight gain for spent fuel fragments with a burnup of 29,000 MWd/MTU. Canadian investigators had found that powder formed at intermediate levels of weight gain in CANDU spent fuel fragments with an approximate burnup of 8000 MWd/MTU. The combined effects of the high rate of weight gain in spent fuel and the burnup dependence of weight gain at powder formation resulted in a minimum in a plot of the time for the onset of powder formation versus burnup. The minimum in powder induction time occurs at or below burnup levels typical of CANDU spent fuel and spent fuel at the ends of some LWR rods. The results are described in terms of thermal and neutron irradiation-induced changes in UO 2 pellet structure and chemical composition. Other tests were performed at up to 275 0 C with spent fuel fragments and nonirradiated UO 2 pellets in moist nitrogen to determine the suitability of nitrogen as a cover gas. No measurable weight gain or visible physical changes occurred during the first 2 months of testing. 22 figures, 7 tables

/sup 14/C-glycocholate breath test and pathological digestive transit

Energy Technology Data Exchange (ETDEWEB)

Talbot, J N; Coutris, G; Charpentier, G; Milhaud, G [Hopital Saint-Antoine, Paris (France)

1982-01-01

/sup 14/C-glycine glycocholate breath test is elegant, atraumatic and detects bacterial overgrowth in the proximal portion of small intestine. In such cases an early increase of specific radioactivity of CO/sub 2/ occurs in expired air. Ileal bile salts malabsorption can also induce such an increase in principle later. However, a modification of transit (acceleration or paresis) can shift the time of appearance of the physiological /sup 14/CO/sub 2/ peak due to colonic deconjugation of the labelled tracer, leading to a diagnostic error. Microbial overgrowth, gastroparesis, accelerated intestinal transit or malabsorption can complicate diabetes mellitus, especially in the case of diabetic neuropathy. Several of these disorder can coexist. It is possible to detect and quantify all these abnormalities in a single examination by the simultaneous use of labelled glycocholate and sup(99m)Tc DTPA. Oral administration of this mixture allows the measurement of gastric emptying half-time and the scintigraphic visualisation of labelled meal progression. Thus, the association of /sup 14/C-glycocholate breath-test and sup(99m)Tc DTPA digestive transit insures a correct interpretation in case of associated abnormalities.

Soil [N] modulates soil C cycling in CO2-fumigated tree stands

DEFF Research Database (Denmark)

Dieleman, W. I. J.; Luyssaert, S.; Rey, A.

2010-01-01

Under elevated atmospheric CO2 concentrations, soil carbon (C) inputs are typically enhanced, suggesting larger soil C sequestration potential. However, soil C losses also increase and progressive nitrogen (N) limitation to plant growth may reduce the CO2 effect on soil C inputs with time. We...... compiled a data set from 131 manipulation experiments, and used meta-analysis to test the hypotheses that: (1) elevated atmospheric CO2 stimulates soil C inputs more than C losses, resulting in increasing soil C stocks; and (2) that these responses are modulated by N. Our results confirm that elevated CO2...... induces a C allocation shift towards below-ground biomass compartments. However, the increased soil C inputs were offset by increased heterotrophic respiration (Rh), such that soil C content was not affected by elevated CO2. Soil N concentration strongly interacted with CO2 fumigation: the effect...

Synthesis and Performance of Tungsten Disulfide/Carbon (WS2/C) Composite as Anode Material

Science.gov (United States)

Yuan, Zhengyong; Jiang, Qiang; Feng, Chuanqi; Chen, Xiao; Guo, Zaiping

2018-01-01

The precursors of an amorphous WS2/C composite were synthesized by a simple hydrothermal method using Na2WO4·2H2O and CH3CSNH2 as raw materials, polyethylene glycol as dispersant, and glucose as the carbon source. The as-synthesized precursors were further annealed at a low temperature in flowing argon to obtain the final materials (WS2/C composite). The structure and morphology of the WS2/C composite were characterized by x-ray diffraction, x-ray photoelectron spectroscopy, and scanning electron microscopy. The electrochemical properties were tested by galvanostatic charge/discharge testing and alternating current (AC) impedance measurements. The results show that the as-prepared amorphous WS2/C composite features both high specific capacity and good cycling performance at room temperature within the potential window from 3.0 V to 0.01 V (versus Li+/Li) at current density of 100 mAg-1. The achieved initial discharge capacity was 1080 mAhg-1, and 786 mAhg-1 was retained after 170 cycles. Furthermore, the amorphous WS2/C composite exhibited a lower charge/discharge plateau than bare WS2, which is more beneficial for use as an anode. The cyclic voltammetry and AC impedance testing further confirmed the change in the plateau and the decrease in the charge transfer resistance in the WS2/C composite. The chemical formation process and the electrochemical mechanism of the WS2/C composite are also presented. The amorphous WS2/C composite can be used as a new anode material for future applications.

The role of C2-C7 and O-C2 angle in the development of dysphagia after cervical spine surgery.

Science.gov (United States)

Tian, Wei; Yu, Jie

2013-06-01

Dysphagia is a known complication of cervical surgery and may be prolonged or occasionally serious. A previous study showed that dysphagia after occipitocervical fusion was caused by oropharyngeal stenosis resulting from O-C2 (upper cervical lordosis) fixation in a flexed position. However, there have been few reports analyzing the association between the C2-C7 angle (middle-lower cervical lordosis) and postoperative dysphagia. The aim of this study was to analyze the relationship between cervical lordosis and the development of dysphagia after anterior and posterior cervical spine surgery (AC and PC). Three hundred fifty-four patients were reviewed in this retrospective clinical study, including 172 patients who underwent the AC procedure and 182 patients who had the PC procedure between June 2007 and May 2010. The presence and duration of postoperative dysphagia were recorded via face-to-face questioning or telephone interview performed at least 1 year after the procedure. Plain cervical radiographs before and after surgery were collected. The O-C2 angle and the C2-C7 angle were measured. Changes in the O-C2 angle and the C2-C7 angle were defined as dO-C2 angle = postoperative O-C2 angle - preoperative O-C2 angle and dC2-C7 angle = postoperative C2-C7 angle - preoperative C2-C7 angle. The association between postoperative dysphagia with dO-C2 angle and dC2-C7 angle was studied. Results showed that 12.8 % of AC and 9.4 % of PC patients reported dysphagia after cervical surgery. The dC2-C7 angle has considerable impact on postoperative dysphagia. When the dC2-C7 angle is greater than 5°, the chance of developing postoperative dysphagia is significantly greater. The dO-C2 angle, age, gender, BMI, operative time, blood loss, procedure type, revision surgery, most cephalic operative level, and number of operative levels did not significantly influence the incidence of postoperative dysphagia. No relationship was found between the dC2-C7 angle and the degree of

I and C functional test facility user guide

International Nuclear Information System (INIS)

Kwon, Ki Chun

1996-07-01

The objective of I and C functional test facility (FTF) is to validate newly developed digital control and protection algorithm, alarm reduction algorithm and the function of operator support system and so on. Test facility is divided into three major parts; software, hardware and graphic user interface. Software consists of mathematical modeling which simulates 3 loop pressurizer water reactor, 993 MWe Westinghouse plant and supervisory module which interpret user instructions and data interface program. FTF is implemented in HP747I workstation using FORTRAN77 and ''C'' language under UNIX operating system. This User Guide provides file structure, instructions and program modification method and provides initial data, malfunction list, process variables list and simulation diagram as an appendix to test developed prototype. 12 figs. (Author)

I and C functional test facility user guide

Energy Technology Data Exchange (ETDEWEB)

Kwon, Ki Chun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1996-07-01

The objective of I and C functional test facility (FTF) is to validate newly developed digital control and protection algorithm, alarm reduction algorithm and the function of operator support system and so on. Test facility is divided into three major parts; software, hardware and graphic user interface. Software consists of mathematical modeling which simulates 3 loop pressurizer water reactor, 993 MWe Westinghouse plant and supervisory module which interpret user instructions and data interface program. FTF is implemented in HP747I workstation using FORTRAN77 and ``C`` language under UNIX operating system. This User Guide provides file structure, instructions and program modification method and provides initial data, malfunction list, process variables list and simulation diagram as an appendix to test developed prototype. 12 figs. (Author).

Study on operation I and C DCS test method of EPR project

International Nuclear Information System (INIS)

Meng Ying; Lv Zhihong; Huang Xinnian; Fan Haiying; Li Zhuojia; Xiao Shushu

2014-01-01

Through summarization and optimization of the method for operation I and C DCS test of the European pressurized reactor project, the conclusions play a guiding role on the operation I and C DCS test of the domestic advanced nuclear power plant. The study of the method focuses on the test platform, the test process and the optimization of method of operation I and C DCS test with the practical experience. The reasonable and reliable test method for operation I and C DCS test of the European pressurized reactor project is worthy of the reference and the development in the project of the domestic advanced nuclear power plant. (authors)

An optimized methodology for combined phenotyping and genotyping on CYP2D6 and CYP2C19

NARCIS (Netherlands)

Tamminga, C.A; Wemer, J; Oosterhuis, B; Brakenhoff, J.P G; Gerrits, M.G F; de Zeeuw, R.A; de Leij, Lou; Jonkman, J.H.G.

A method for simultaneous phenotyping and genotyping for CYP2D6 and CYP2C19 was tested. Six healthy volunteers were selected (three extensive and three poor metabolisers for CYP2D6). CYP2D6 was probed with dextromethorphan and metoprolol and CYP2C19 was probed with omeprazole. Blood samples were

Synthesis of [5,6-13C2, 1-14C]olivetolic acid, methyl [1'-13C]olivetolate and [5,6-13C2, 1-14C]cannabigerolic acid

International Nuclear Information System (INIS)

Porwoll, J.P.; Leete, E.

1985-01-01

Potential advanced intermediates in the biosynthesis of delta 9 -tetrahydrocannabinol, the major psychoactive principle of marijuana, have been synthesized labeled with two contiguous 13 C atoms and 14 C. Methyl [5,6- 13 C 2 , 1- 14 C]olivetolate was prepared from lithium [ 13 C 2 ]acetylide and dimethyl [2- 14 C]malonate. Reaction with geranyl bromide afforded methyl [5,6- 13 C 2 , 1- 14 C]cannabigerolate, and hydrolysis of these methyl esters with lithium propyl mercaptide yielded the corresponding labeled acids. The 13 C- 13 C couplings observable in the 13 C NMR spectra of these 13 C-enriched compounds and their synthetic precursors are recorded. Methyl [1'- 14 C]olivetolate was prepared from 13 CO 2 to confirm assignments of the 13 C chemical shifts in the pentyl side chain of these compounds. (author)

Electronic Structures and Bonding Properties of Ti2AlC and Ti3AlC2

Institute of Scientific and Technical Information of China (English)

MIN Xinmin; REN Yi

2007-01-01

The relation among electronic structure, chemical bond and property of Ti2AlC, Ti3AlC2 and doping Si into Ti2AlC was studied by density function and the discrete variation (DFT-DVM) method. After adding Si into Ti2AlC, the interaction between Si and Ti is weaker than that between Al and Ti, and the strengths of ionic and covalent bonds decrease both. The ionic and covalent bonds in Ti3AlC2, especially in Ti-Al, are stronger than those in Ti2AlC. Therefore, in synthesis of Ti2AlC, the addition of Si enhances the Ti3AlC2 content instead of Ti2AlC. The density of state (DOS) shows that there is mixed conductor characteristic in Ti2AlC and Ti3AlC2. The DOS of Ti3AlC2 is much like that of Ti2AlC. Ti2SixAl1-x C has more obvious tendency to form a semiconductor than Ti2AlC, which is seen from the obvious difference of partial DOS between Si and Al3p.

Nido-Carborane building-block reagents. 2. Bulky-substituent (alkyl)2C2B4H6 derivatives and (C6H5)2C2B4H6: synthesis and properties

International Nuclear Information System (INIS)

Boyter, H.A. Jr.; Grimes, R.N.

1988-01-01

The preparation and chemistry of nido-2,3-R 2 C 2 C 2 B 4 H 6 carboranes in which R is n-butyl, isopentyl, n-hexyl, and phenyl was investigated in order to further assess the steric and electronic influence of the R groups on the properties of the nido-C 2 B 4 cage, especially with respect to metal complexation at the C 2 B 3 face and metal-promoted oxidative fusion. The three dialkyl derivatives were prepared from the corresponding dialkylacetylenes via reaction with B 5 H 9 and triethylamine, but the diphenyl compound could not be prepared in this manner and was obtained instead in a thermal reaction of B 5 H 9 with diphenylacetylene in the absence of amine. All four carboranes are readily bridge-deprotonated by NaH in THF, and the anions of the dialkyl species, on treatment with FeCl 2 and air oxidation, generate the respective R 4 C 4 B 8 H 8 carborane fusion products were R = n-C 4 H 9 , i-C 5 H 11 or n-C 6 H 13 . The diphenylcarborane anion Ph 2 C 2 B 4 H 5 - did not form detectable metal complexes with Fe 2+ , Co 2+ , or Ni 2+ , and no evidence of a Ph 4 C 4 B 8 H 8 fusion product has been found. Treatment of Ph 2 C 2 B 4 H 6 with Cr(CO) 6 did not lead to metal coordination of the phenyl rings, unlike (PhCH 2 ) 2 C 2 B 4 H 6 , which had previously been shown to form mono- and bis(tricarbonylchromium) complexes. However, the reaction of Ph 2 C 2 B 4 H 5 - , CoCl 2 , and (PhPCH 2 ) 2 did give 1,1-(Ph 2 PCH 2 ) 2 -1-Cl-1,2,3-Co(Ph 2 C 2 B 4 H 4 ), the only case in which metal complexation of the diphenylcarborane was observed. 14 references, 3 figures, 3 tables

Adapting the Body Appreciation Scale-2 for Children: A psychometric analysis of the BAS-2C.

Science.gov (United States)

Halliwell, Emma; Jarman, Hannah; Tylka, Tracy; Slater, Amy

2017-06-01

Positive body image among adults is related to numerous indicators of well-being. However, no research has explored body appreciation among children. To facilitate our understanding of children's positive body image, the current study adapts and validates the Body Appreciation Scale-2 (BAS-2; Tylka & Wood-Barcalow, 2015a) for use with children. Three hundred and forty-four children (54.4% girls) aged 9-11 completed the adapted Body Appreciation Scale-2 for Children (BAS-2C) alongside measures of body esteem, media influence, body surveillance, mood, and dieting. A sub-sample of 154 participants (62.3% girls) completed the questionnaire 6-weeks later to examine stability (test-retest) reliability. The BAS-2C displayed a unidimensional factor structure and evidence of internal consistency, test-retest reliability, and construct, criterion-related, and incremental validity. Additionally, the results suggest adaptive properties of body appreciation for body-related and emotional well-being among children. The BAS-2C could serve as an essential component within research to understand and estimate children's positive body image. Copyright © 2017. Published by Elsevier Ltd.

21 CFR 862.1090 - Angiotensin converting enzyme (A.C.E.) test system.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Angiotensin converting enzyme (A.C.E.) test system... Test Systems § 862.1090 Angiotensin converting enzyme (A.C.E.) test system. (a) Identification. An angiotensin converting enzyme (A.C.E.) test system is a device intended to measure the activity of angiotensin...

C-13-carbohydrate breath tests : Impact of physical activity on the rate-limiting step in lactose utilization

NARCIS (Netherlands)

Stellaard, F; Koetse, HA; Elzinga, H; Boverhof, R; Tjoonk, R; Klimp, A; Vegter, D; Liesker, J; Vonk, RJ

Background: (CO2)-C-13 breath tests can be used to monitor carbohydrate digestion in the small intestine. However, after ingestion of C-13-substrates, (CO2)-C-13 excretion in breath originates from two sources: a digestive/oxidative fraction, derived from the small intestine, and a fermentation

Experimental study on L-[1-13C] phenylalanine breath test for quantitative assessment of liver function with animal

International Nuclear Information System (INIS)

Yan Weili; Fudan Univ., Shanghai; Lin Xiangtong; Sun Dayu; Jiang Yibin; Sun Xu; Rong Lan; Liang Qi

2006-01-01

Objective: Using a small animal breath test model we designed and L-[1- 13 C] phenylalanine breath test ( 13 C-PheBT) of rats, the authors investigated its feasibility and validity and determined effective parameter of the test. Methods: Twenty male Sprague-Dawley (SD) weighting 280-290 g rats randomized into two groups acute hepatitis rats (n=10) and control rats (n=10). Hepatitis was induced by carbon tetrachloride (CCl 4 ) olive oil administration through intragastric gavage. PheBT was assisted by small mechanical ventilator improved and air samples were collected discontinuously, 20 mg/kg body weight L-[1- 13 C] phenylalanine ( 13 C-Phe) was administered intravenously. Twenty-nine breath samples were taken before and different intervals within sixty minutes after administration. 13 Cenrichment was measured by isotope ratio mass spectrometer. Results: All time phase curves of 13 C enrichment in rat breath reached a peak almost at 2 min after the intravenous administration of 13 C-Phe. The PheBT parameters, 13 C excretion rate constant (PheBT-K), of CCl 4 hepatitis rats were significantly lower than that of normal control rats [(2.45 ± 0.25) x 10 -2 min -1 vs (2.98 ± 0.19) x 10 -2 min -1 , t = 5.40, P 13 C fast phase disposition constant did not statistically differ between the two groups (t=0.58, P>0.05). PheBT-K had significant negative cor-relation with serum ALT, AKP, TBA and total bilirum TBIL (the correlation coefficient r is -0.74, -0.73, -0.82 and -0.67 respectively, P 0.05). Conclusions: It was indicated that the small animal breath test model we designed was a virtual tool to use in experimental study on breath test and PheBT-K was a sensitive index. (authors)

The Tritiated Water Skin Barrier Integrity Test: Considerations for Acceptance Criteria with and Without 14C-Octanol.

Science.gov (United States)

Lehman, Paul A; Beatch, Kacie; Raney, Sam G; Franz, Thomas J

2017-01-01

A study was designed to assess barrier integrity simultaneously using separate compounds (probes) for polar and non-polar pathways through the skin, 3 H 2 O and 14 C-octanol, respectively; and to determine whether the two probe approach could better define barrier integrity. A 5-min dose of water containing 3 H 2 O and 14 C -octanol was applied to ex vivo human skin mounted in Franz diffusion cells. The receptor solution was sampled at 30 min, analyzed for 3 H and 14 C content, and the correlation between water and octanol absorption was determined by statistical tests suitable for non-normally distributed data. This study was conducted on skin from 37 donors with from 3 to 30 replicate skin sections per donor (a total of 426 sections). The correlation between 3 H 2 O and 14 C-octanol absorption was low (Pearson correlation coefficient = 0.3485). The 3 H 2 O absorption cutoff used in this study to select for a normal skin barrier rejected some sections in which 14 C-octanol absorption was within normal limits and accepted others in which 14 C-octanol absorption was abnormally high. The converse was true for 3 H 2 O absorption when the 14 C-octanol-based cutoff was used. The results of the 3 H 2 O test or of similar tests that primarily assess the permeability of polar pathways through the skin may not necessarily provide information relevant to the absorption of highly lipophilic compounds. Octanol, or another molecule that more closely matches the physicochemical attributes of the test compound, may characterize properties of the skin barrier that are more relevant to compounds of low water solubility.

Defining predictive values using three different platelet function tests for CYP2C19 phenotype status on maintenance dual antiplatelet therapy after PCI.

Science.gov (United States)

Zhang, Hong-Zhe; Kim, Moo Hyun; Han, Jin-Yeong; Jeong, Young-Hoon

2014-01-01

Published data suggests that the presence of CYP2C19*2 or *3 loss of function (LOF) alleles is indicative of increased platelet aggregation and a higher risk of adverse cardiovascular events after clopidogrel administration. We sought to determine cut-off values using three different assays for prediction of the CYP2C19 phenotype in Korean percutaneous coronary intervention (PCI) patients. We enrolled 244 patients with drug-eluting stent implantation who were receiving clopidogrel and aspirin maintenance therapy for one month or more. Platelet reactivity was assessed with light transmittance aggregometry (LTA), multiple electrode aggregometry (MEA) and the VerifyNow P2Y12 assay (VN). The CYP2C19 genotype was analyzed by polymerase chain reaction (PCR) and snapshot method. The frequency of CYP2C19 LOF allele carriers was 58.6%. The cut-off values from LTA, MEA and VerifyNow for the identification of LOF allele carriers were as follows: 10 µM ADP-induced LTA ≥ 48 %, VN>242 PRU and MEA ≥ 37 U. Between the three tests, correlation was higher between LTA vs. VN assays (r=0.69) and LTA vs. MEA (r=0.56), with moderate agreement (κ=0.46 and κ=0.46), but between VN assay and MEA, both devices using whole blood showed a lower correlation (r=0.42) and agreement (κ=0.3). Our results provide guidance regarding cut-off levels for LTA, VerifyNow and MEA assays to detect the CYP2C19 LOF allele in patients during dual antiplatelet maintenance therapy.

Benchmark and physics testing of LIFE-4C. Summary

International Nuclear Information System (INIS)

Liu, Y.Y.

1984-06-01

LIFE-4C is a steady-state/transient analysis code developed for performance evaluation of carbide [(U,Pu)C and UC] fuel elements in advanced LMFBRs. This paper summarizes selected results obtained during a crucial step in the development of LIFE-4C - benchmark and physics testing

Tunable Robust pacs-MOFs: a Platform for Systematic Enhancement of the C2H2 Uptake and C2H2/C2H4 Separation Performance.

Science.gov (United States)

Chen, Di-Ming; Sun, Chun-Xiao; Zhang, Nan-Nan; Si, Huan-Huan; Liu, Chun-Sen; Du, Miao

2018-03-05

As a modulatable class of porous crystalline materials, metal-organic frameworks (MOFs) have gained intensive research attention in the domain of gas storage and separation. In this study, we report on the synthesis and gas adsorption properties of two robust MOFs with the general formula [Co 3 (μ 3 -OH)(cpt) 3 Co 3 (μ 3 -OH)(L) 3 (H 2 O) 9 ](NO 3 ) 4 (guests) n [L = 3-amino-1,2,4-triazole (1) and 3,5-diamino-1,2,4-triazole (2); Hcpt = 4-(4-carboxyphenyl)-1,2,4-triazole], which show the same pacs topology. Both MOFs are isostructural to each other and show MIL-88-type frameworks whose pore spaces are partitioned by different functionlized trinuclear 1,2,4-triazolate-based clusters. The similar framework components with different amounts of functional groups make them an ideal platform to permit a systematic gas sorption/separation study to evaluate the effects of distinctive parameters on the C 2 H 2 uptake and separation performance. Because of the presence of additional amido groups, the MOF 2 equipped with a datz-based cluster (Hdatz = 3,5-diamino-1,2,4-triazole) shows a much improved C 2 H 2 uptake capacity and separation performance over that of the MOF 1 equipped with atz-based clusters (Hatz = 3-amino-1,2,4-triazole), although the surface area of the MOF 1 is almost twice than that of the MOF 2. Moreover, the high density of open metal sites, abundant free amido groups, and charged framework give the MOF 2 an excellent C 2 H 2 separation performance, with ideal adsorbed solution theory selectivity values reaching up to 11.5 and 13 for C 2 H 2 /C 2 H 4 (1:99) and C 2 H 2 /CO 2 (50:50) at 298 K and 1 bar, showing potential for use in natural gas purification.

The sup 14 C-urea breath-test for the detection of gastric Campylobacter pylori infection

Energy Technology Data Exchange (ETDEWEB)

Surveyor, I; Goodwin, C S; Mullan, B P; Geelhoed, E; Warren, J R; Murray, R N; Waters, T E; Sanderson, C R [Royal Perth Hospital (Australia)

1989-10-16

Sixty-three patients who were undergoing endoscopy were studied. The radioactivity in exhaled breath which was sampled within five minutes of {sup 14}C -urea administration was attributed to the presence of urease enzyme in mouth organisms and was discounted. The time-radioactivity curves for breath samples from five to 30 minutes after the administration of {sup 14}C-urea gave an excellent separation between subjects with negative results of the examination of gastric-biopsy samples and patients with microbiological and histological evidence of infection with Campylobacter (C.) pylori. The area under the time-radioactivity curve at between five and 30 minutes after the administration of {sup 14}C-urea in 24 patients with negative microbiological results was 6.9{plus minus}4.4 area units; in 35 of 39 patients with positive microbiological results, this area was greater than 40 area units. Measured against the results of the microbiological examination of gastricbiopsy samples, the sensitivity of breath-testing was 90% and the specificity was 100%. Measured against the results of histological examination for the presence of C. pylori infection, breath-testing had a sensitivity of 94% and a specificity of 93%. A positive breath-test result also correlated well (P=0.0001) with the serological antibody test-result. The role of non-invasive tests - enzyme-linked immunosorbent assays and {sup 14}C-urea breath-testing - in the management of gastritis and peptic ulcer disease is discussed. We consider that the {sup 14}C-urea breath-test has an important role in the noninvasive confirmation of gastric infection with C. pylori and in the follow-up of patients after treatment. 38 refs., 2 figs., 1 tab.

Genotype-Dependent Difference in 5-HT2C Receptor-Induced Hypolocomotion: Comparison with 5-HT2A Receptor Functional Activity

Directory of Open Access Journals (Sweden)

Darya V. Bazovkina

2015-01-01

Full Text Available In the present study behavioral effects of the 5-HT2C serotonin receptor were investigated in different mouse strains. The 5-HT2C receptor agonist MK-212 applied intraperitoneally induced significant dose-dependent reduction of distance traveled in the open field test in CBA/Lac mice. This effect was receptor-specific because it was inhibited by the 5-HT2C receptor antagonist RS102221. To study the role of genotype in 5-HT2C receptor-induced hypolocomotion, locomotor activity of seven inbred mouse strains was measured after MK-212 acute treatment. We found that the 5-HT2C receptor stimulation by MK-212 decreased distance traveled in the open field test in CBA/Lac, C57Bl/6, C3H/He, and ICR mice, whereas it failed to affect locomotor activity in DBA/2J, Asn, and Balb/c mice. We also compared the interstrain differences in functional response to 5-HT2C and 5-HT2A receptors activation measured by the quantification of receptor-mediated head-twitches. These experiments revealed significant positive correlation between 5-HT2C and 5-HT2A receptors functional responses for all investigated mouse strains. Moreover, we found that 5-HT2A receptor activation with DOI did not change locomotor activity in CBA/Lac mice. Taken together, our data indicate the implication of 5-HT2C receptors in regulation of locomotor activity and suggest the shared mechanism for functional responses mediated by 5-HT2C and 5-HT2A receptors.

Evaluation report on CCTF Core-II reflood test C2-9 (Run 68)

International Nuclear Information System (INIS)

Akimoto, Hajime; Iguchi, Tadashi; Okubo, Tsutomu; Murao, Yoshio; Okabe, Kazuharu; Sugimoto, Jun.

1987-02-01

In order to study the LPCI flow rate effect on the core cooling and system behavior, a test was performed with the LPCI flow rate of 0.025 m 3 /s, which corresponds to the flow rate in case of no pump failure in a PWR system. Through the comparisons of test results with those from the reference test with the LPCI flow rate of 0.011 m 3 /s, the following conclusions were obtained: (1) The higher LPCI flow rate resulted in the worse core-cooling in these two tests. The test results show that the lower LPCI flow rate is not necessarily a conservative assumption for the evaluation of the core cooling during the reflood phase of a PWR LOCA. (2) The worse core-cooling in the high LPCI flow rate test is attributed to the lower core-pressure than in the reference test. It is found that the lower core-pressure results from the lower pressure drop through the broken cold leg. (3) It is expected that the current evaluation model(EM) code is still conservative because it usually predicts the low pressure drop through the broken cold leg. (4) The flow oscillation in the cold leg was not significant even in the high LPCI flow rate test before the whole core quench. (author)

New metal-organic frameworks of [M(C6H5O7)(C6H6O7)(C6H7O7)(H2O)] . H2O (M=La, Ce) and [Ce2(C2O4)(C6H6O7)2] . 4H2O

International Nuclear Information System (INIS)

Weng Shengfeng; Wang, Yun-Hsin; Lee, Chi-Shen

2012-01-01

Two novel materials, [M(C 6 H 5 O 7 )(C 6 H 6 O 7 )(C 6 H 7 O 7 )(H 2 O)] . H 2 O (M=La(1a), Ce(1b)) and [Ce 2 (C 2 O 4 )(C 6 H 6 O 7 ) 2 ] . 4H 2 O (2), with a metal-organic framework (MOF) were prepared with hydrothermal reactions and characterized with photoluminescence, magnetic susceptibility, thermogravimetric analysis and X-ray powder diffraction in situ. The crystal structures were determined by single-crystal X-ray diffraction. Compound 1 crystallized in triclinic space group P1-bar (No. 2); compound 2 crystallized in monoclinic space group P2 1 /c (No. 14). The structure of 1 is built from a 1D MOF, composed of deprotonated citric ligands of three kinds. Compound 2 contains a 2D MOF structure consisting of citrate and oxalate ligands; the oxalate ligand arose from the decomposition in situ of citric acid in the presence of Cu II ions. Photoluminescence spectra of compounds 1b and 2 revealed transitions between the 5d 1 excited state and two levels of the 4f 1 ground state ( 2 F 5/2 and 2 F 7/2 ). Compounds 1b and 2 containing Ce III ion exhibit a paramagnetic property with weak antiferromagnetic interactions between the two adjacent magnetic centers. - Graphical Abstract: [M(C 6 H 5 O 7 )(C 6 H 6 O 7 )(C 6 H 7 O 7 )(H 2 O)] . H 2 O (M=La(1a), Ce(1b)) and [Ce 2 (C 2 O 4 )(C 6 H 6 O 7 ) 2 ] . 4H 2 O (2)—with 1D and 2D structures were synthesized and characterized. Highlights: ► Two MOF – [M(C 6 H 5 O 7 )(C 6 H 6 O 7 )(C 6 H 7 O 7 )(H 2 O)] . H 2 O (M=La(1a), Ce(1b)) and [Ce 2 (C 2 O 4 )(C 6 H 6 O 7 ) 2 ] . 4H 2 O (2) – with 1D and 2D structures. ► The adjacent chains of the 1D framework were correlated with each other through an oxalate ligand to form a 2D layer structure. ► The source of the oxalate ligand was the decomposition in situ of citric acid oxidized in the presence of Cu II ions.

Comparative study of electron-impact C(1s) core-excitation processes in C{sub 2} and C{sub 2}N{sub 2} molecules

Energy Technology Data Exchange (ETDEWEB)

Michelin, S.E. [Departamento de Fisica, Universidade Federal de Santa Catarina, 88040-900 Florianopolis, SC (Brazil)], E-mail: fsc1sem@fsc.ufsc.br; Mazon, K.T.; Arretche, F.; Tenfen, W.; Oliveira, H.L.; Falck, A.S.; Scopel, M.A.; Silva, L.S.S. da [Departamento de Fisica, Universidade Federal de Santa Catarina, 88040-900 Florianopolis, SC (Brazil); Fujimoto, M.M. [Departamento de Fisica, Universidade Federal do Parana, 81531-990 Curitiba, PR (Brazil); Iga, I.; Lee, M.-T. [Departamento de Quimica, Universidade Federal de Sao Carlos, 13565-905, Sao Carlos, SP (Brazil)

2009-04-15

Distorted-wave approximation (DWA) is applied to study core-orbital excitations in C{sub 2}and C{sub 2}N{sub 2} molecules by electron impact. More specifically, we report calculated integral cross sections (ICS) for the X{sup 1}{sigma}{sub g}{sup +}{yields}{sup 1,3}{pi}{sub u}(1s{sigma}{sub u}{yields}1p{pi}{sub g}) and X{sup 1}{sigma}{sub g}{sup +}{yields}{sup 1,3}{pi}{sub g}(1s{sigma}{sub g}{yields}1p{pi}{sub g}) transitions in the C{sub 2}, and X{sup 1}{sigma}{sub g}{sup +}{yields}{sup 1,3}{pi}{sub g}(2s{sigma}{sub g}{yields}2p{pi}{sub g}) and X{sup 1}{sigma}{sub g}{sup +}{yields}{sup 1,3}{pi}{sub u}(2s{sigma}{sub u}{yields}2p{pi}{sub g}) transitions in the C{sub 2}N{sub 2} molecules in the 300-800 eV incident energy range. The comparison of the calculated ICS of these targets with the corresponding data for C{sub 2}H{sub 2} presented. Comparison is also made for the theoretical RI(3:1) ratios of these targets which are calculated by dividing the ICS for triplet transitions by the corresponding results for singlet transitions. The similarities and differences of these results, particularly the presence of the shape resonances at near excitation thresholds, are discussed. The influence of the atomic (localized) and molecular (delocalized) characters of the core orbitals on the core-excitation processes is also investigated. In addition, generalized oscillator strengths for the singlet core-orbital transitions are calculated at incident energy of 1290 eV for C{sub 2} and C{sub 2}N{sub 2}. A comparison with the existing theoretical and experimental data for C{sub 2}H{sub 2} is also presented.

Um estudo teórico de propriedades moleculares em complexos de hidrogênio trimoleculares C2H4···2HF, C2H2···2HF e C3h6···2HF A theoretical study of molecular properties of C2H4···2HF, C2H2···2HF AND C3H6···2HF trimolecular hydrogen-bonded complexes

Directory of Open Access Journals (Sweden)

Boaz G. Oliveira

2008-01-01

Full Text Available We present a theoretical study of molecular properties in C2H4···2HF, C2H2···2HF and C3H6···2HF trimolecular hydrogen-bonded complexes. From B3LYP/6-311++G(d,p calculations, the most important structural deformations are related to the C=C (C2H4, C≡C (C2H2, C-C (C3H6 and HF bond lengths. According to the Bader's atoms in molecules and CHELPG calculations, it was identified a tertiary interaction between the fluorine atom of the second hydrofluoric acid molecule and hydrogen atoms of the ethylene and acetylene within the C2H4···2HF and C2H2···2HF complexes, respectively. Additionally, the evaluation of the infrared spectrum characterized the new vibrational modes and bathochromic effect of the HF molecules.

Predictors of hepatitis C testing intention among African American Baby Boomers

Directory of Open Access Journals (Sweden)

Mohamed Rashrash

2017-06-01

Full Text Available Baby Boomers (BBs are responsible for three-quarters of hepatitis C virus (HCV infections in the United States; however, HCV testing is distinctly underused by them. A cross-sectional study was conducted to assess the prevalence of HCV testing and to evaluate predictors of HCV testing intention among African–American BBs. The study was guided by the Health Belief Model and theory of reasoned action frameworks. Of the 137 participants included in the study, 44.8% had at least a college education; 13.9% received prior to 1992 blood transfusion. Findings related to HCV testing showed that 32.1% of the participants intended to test for HCV within 6 months and 43.8% had received a previous HCV test. Significant predictors of HCV testing intention within 6 months included having a blood transfusion prior to 1992 [odds ratio (OR = 8.25, 95% confidence interval (CI: 2.02–33.61], perceptions of benefits (OR = 1.57, 95% CI: 1.13–2.18, severity (OR = 1.39, 95% CI: 1.17–1.65, and subjective norms (OR = 1.42, 95% CI: 1.12–1.79. These predictors of HCV testing intention can be used to develop future HCV testing initiatives for African–American BBs.

Schwann Cells Metabolize Extracellular 2′,3′-cAMP to 2′-AMP

Science.gov (United States)

Verrier, Jonathan D.; Kochanek, Patrick M.

2015-01-01

The 3′,5′-cAMP–adenosine pathway (3′,5′-cAMP→5′-AMP→adenosine) and the 2′,3′-cAMP–adenosine pathway (2′,3′-cAMP→2′-AMP/3′-AMP→adenosine) are active in the brain. Oligodendrocytes participate in the brain 2′,3′-cAMP–adenosine pathway via their robust expression of 2′,3′-cyclic nucleotide 3′-phosphodiesterase (CNPase; converts 2′,3′-cAMP to 2′-AMP). Because Schwann cells also express CNPase, it is conceivable that the 2′,3′-cAMP–adenosine pathway exists in the peripheral nervous system. To test this and to compare the 2′,3′-cAMP–adenosine pathway to the 3′,5′-cAMP–adenosine pathway in Schwann cells, we examined the metabolism of 2′,3′-cAMP, 2′-AMP, 3′-AMP, 3′,5′-cAMP, and 5′-AMP in primary rat Schwann cells in culture. Addition of 2′,3′-cAMP (3, 10, and 30 µM) to Schwann cells increased levels of 2′-AMP in the medium from 0.006 ± 0.002 to 21 ± 2, 70 ± 3, and 187 ± 10 nM/µg protein, respectively; in contrast, Schwann cells had little ability to convert 2′,3′-cAMP to 3′-AMP or 3′,5′-cAMP to either 3′-AMP or 5′-AMP. Although Schwann cells slightly converted 2′,3′-cAMP and 2′-AMP to adenosine, they did so at very modest rates (e.g., 5- and 3-fold, respectively, more slowly compared with our previously reported studies in oligodendrocytes). Using transected myelinated rat sciatic nerves in culture medium, we observed a time-related increase in endogenous intracellular 2′,3′-cAMP and extracellular 2′-AMP. These findings indicate that Schwann cells do not have a robust 3′,5′-cAMP–adenosine pathway but do have a 2′,3′-cAMP–adenosine pathway; however, because the pathway mostly involves 2′-AMP formation rather than 3′-AMP, and because the conversion of 2′-AMP to adenosine is slow, metabolism of 2′,3′-cAMP mostly results in the accumulation of 2′-AMP. Accumulation of 2′-AMP in peripheral nerves postinjury could have

Simultaneous 13C/14C dual isotope breath test measurement of gastric emptying of solid and liquid in normal subjects and patients: comparison with scintigraphy

International Nuclear Information System (INIS)

Chew, C. G.; Bartholomeusz, F.D.L.; Bellon, M.; Chatterton, B. E.

2003-01-01

To develop a simple method for simultaneous solid and liquid gastric emptying assessment using a dual isotope labelled breath test. 13 patients were given 100 g ground beef labelled with 25 MBq 99m Tc sulphur colloid and 74 KBq 14 C octanoic acid, and 150 ml 10% glucose drink labelled with 8 MBq 67 Ga citrate and 150 mg 13 C acetate. 10 normal volunteers were given the same test meals but labelled with 14 C and 13 C only. Breath was collected at baseline and regularly for 4 hours. The 14 CO 2 and 13 CO 2 activity was measured with liquid scintillation counting and mass spectroscopy. The times to maximum 14 CO 2 and 13 CO 2 , were determined. Comparison was made between times to maximum 14 CO 2 with scintigraphic retention of 99m Tc at 100 minutes and times to maximum 13 CO 2 with the scintigraphic half-clearance time of 67 Ga. For the solid meal, the times to maximum 14 CO 2 were: 60-120 minutes in the 8 patients with normal gastric emptying of 99m Tc; 75-145 minutes for the 10 healthy volunteers; 75-180 minutes for the remaining 5 patients with abnormal gastric emptying of 99m Tc. There was a weak but significant correlation (r = 0.56, p 14 CO 2 and gastric retention of 99m Tc at 100 minutes. For the liquid meal, times to maximum 13 CO 2 were: 20-35 minutes for the 4 with normal gastric emptying of 67 Ga; 15-40 minutes for the 10 healthy volunteers; 20-75 minutes for the remaining 9 patients with abnormal gastric emptying of 67 Ga. There was a strong and significant correlation (r = 0.88, p 13 CO 2 and gastric half-clearance time of 67 Ga. Breath tests utilising test meals labelled with *C isotopes are valid alternatives to scintigraphic studies using 99m Tc and 67 Ga for the simultaneous assessment of gastric emptying of solids and liquids. (author)

Results of Characterization and Retrieval Testing on Tank 241-C-110 Heel Solids

Energy Technology Data Exchange (ETDEWEB)

Callaway, William S.

2013-09-30

Nine samples of heel solids from tank 241-C-110 were delivered to the 222-S Laboratory for characterization and dissolution testing. After being drained thoroughly, the sample solids were primarily white to light-brown with minor dark-colored inclusions. The maximum dimension of the majority of the solids was <2 mm; however, numerous pieces of aggregate, microcrystalline, and crystalline solids with maximum dimensions ranging from 5-70 mm were observed. In general, the larger pieces of aggregate solids were strongly cemented. Natrophosphate [Na{sub 7}F(PO{sub 4}){sub 2}°19H{sub 2}O] was the dominant solid phase identified in the heel solids. Results of chemical analyses suggested that 85-87 wt% of the heel solids were the fluoridephosphate double salt. The average bulk density measured for the heel solids was 1.689 g/mL; the reference density of natrophosphate is 1.71 g/mL. Dissolution tests on composite samples indicate that 94 to 97 wt% of the tank 241-C-110 heel solids can be retrieved by dissolution in water. Dissolution and recovery of the soluble components in 1 kg (0.59 L) of the heel solids required the addition of ≈9.5 kg (9.5 L) of water at 15 °C and ≈4.4 kg (4.45 L) of water at 45 °C. Calculations performed using the Environmental Simulation Program indicate that dissolution of the ≈0.86 kg of natrophosphate in each kilogram of the tank 241-C-110 heel solids would require ≈9.45 kg of water at 15 °C and ≈4.25 kg of water at 45 °C. The slightly larger quantities of water determined to be required to retrieve the soluble components in 1 kg of the heel solids are consistent with that required for the dissolution of solids composed mainly of natrophosphate with a major portion of the balance consisting of highly soluble sodium salts. At least 98% of the structural water, soluble phosphate, sodium, fluoride, nitrate, carbonate, nitrite, sulfate, oxalate, and chloride in the test composites was dissolved and recovered in the

Solid-Contact pH Sensor without CO2 Interference with a Superhydrophobic PEDOT-C14 as Solid Contact: The Ultimate "Water Layer" Test.

Science.gov (United States)

Guzinski, Marcin; Jarvis, Jennifer M; D'Orazio, Paul; Izadyar, Anahita; Pendley, Bradford D; Lindner, Ernő

2017-08-15

The aim of this study was to find a conducting polymer-based solid contact (SC) for ion-selective electrodes (ISEs) that could become the ultimate, generally applicable SC, which in combination with all kinds of ion-selective membranes (ISMs) would match the performance characteristics of conventional ISEs. We present data collected with electrodes utilizing PEDOT-C 14 , a highly hydrophobic derivative of poly(3,4-ethylenedioxythiophene), PEDOT, as SC and compare its performance characteristics with PEDOT-based SC ISEs. PEDOT-C 14 has not been used in SC ISEs previously. The PEDOT-C 14 -based solid contact (SC) ion-selective electrodes (ISEs) (H + , K + , and Na + ) have outstanding performance characteristics (theoretical response slope, short equilibration time, excellent potential stability, etc.). Most importantly, PEDOT-C 14 -based SC pH sensors have no CO 2 interference, an essential pH sensors property when aimed for whole-blood analysis. The superhydrophobic properties (water contact angle: 136 ± 5°) of the PEDOT-C 14 SC prevent the detachment of the ion-selective membrane (ISM) from its SC and the accumulation of an aqueous film between the ISM and the SC. The accumulation of an aqueous film between the ISM and its SC has a detrimental effect on the sensor performance. Although there is a test for the presence of an undesirable water layer, if the conditions for this test are not selected properly, it does not provide an unambiguous answer. On the other hand, recording the potential drifts of SC electrodes with pH-sensitive membranes in samples with different CO 2 levels can effectively prove the presence or absence of a water layer in a short time period.

Testing of interposer-based 2.5D integrated circuits

CERN Document Server

Wang, Ran

2017-01-01

This book provides readers with an insightful guide to the design, testing and optimization of 2.5D integrated circuits. The authors describe a set of design-for-test methods to address various challenges posed by the new generation of 2.5D ICs, including pre-bond testing of the silicon interposer, at-speed interconnect testing, built-in self-test architecture, extest scheduling, and a programmable method for low-power scan shift in SoC dies. This book covers many testing techniques that have already been used in mainstream semiconductor companies. Readers will benefit from an in-depth look at test-technology solutions that are needed to make 2.5D ICs a reality and commercially viable. Provides a single-source guide to the practical challenges in testing of 2.5D ICs; Presents an efficient method to locate defects in a passive interposer before stacking; Describes an efficient interconnect-test solution to target through-silicon vias (TSVs), the redistribution layer, and micro-bumps for shorts, opens, and dela...

Direct preparation of 14C-labelled 5-allyl- and 5-propyl-2'-deoxyuridine from [2-14C]2'-deoxyuridine

International Nuclear Information System (INIS)

Ruth, J.L.; White, S.K.; Bergstrom, D.E.

1982-01-01

[2- 14 C]5-Allyl-2'-deoxyuridine was synthesized directly from [2- 14 C]2'-deoxyuridine using mercury, palladium, and 3-chloropropene. [2- 14 C]5-Propyl-2'-deoxyuridine was obtained by hydrogenation of the [ 14 C]5-allyl-2'-deoxyuridine. Advantages of the synthetic method and its application to the preparation of other radiolabeled 5-alkyl/alkenyl-2'-deoxyuridines are discussed. (author)

Routine blood tests to predict liver fibrosis in chronic hepatitis C.

Science.gov (United States)

Hsieh, Yung-Yu; Tung, Shui-Yi; Lee, Kamfai; Wu, Cheng-Shyong; Wei, Kuo-Liang; Shen, Chien-Heng; Chang, Te-Sheng; Lin, Yi-Hsiung

2012-02-28

To verify the usefulness of FibroQ for predicting fibrosis in patients with chronic hepatitis C, compared with other noninvasive tests. This retrospective cohort study included 237 consecutive patients with chronic hepatitis C who had undergone percutaneous liver biopsy before treatment. FibroQ, aspartate aminotransferase (AST)/alanine aminotransferase ratio (AAR), AST to platelet ratio index, cirrhosis discriminant score, age-platelet index (API), Pohl score, FIB-4 index, and Lok's model were calculated and compared. FibroQ, FIB-4, AAR, API and Lok's model results increased significantly as fibrosis advanced (analysis of variance test: P fibrosis score in chronic hepatitis C compared with other noninvasive tests. FibroQ is a simple and useful test for predicting significant fibrosis in patients with chronic hepatitis C.

Results of Characterization and Retrieval Testing on Tank 241-C-109 Heel Solids

Energy Technology Data Exchange (ETDEWEB)

Callaway, William S.

2013-09-26

Eight samples of heel solids from tank 241-C-109 were delivered to the 222-S Laboratory for characterization and dissolution testing. After being drained thoroughly, one-half to two-thirds of the solids were off-white to tan solids that, visually, were fairly evenly graded in size from coarse silt (30-60 μm) to medium pebbles (8-16 mm). The remaining solids were mostly strongly cemented aggregates ranging from coarse pebbles (16-32 mm) to fine cobbles (6-15 cm) in size. Solid phase characterization and chemical analysis indicated that the air-dry heel solids contained ≈58 wt% gibbsite [Al(OH){sub 3}] and ≈37 wt% natrophosphate [Na{sub 7}F(PO{sub 4}){sub 2}·19H{sub 2}O]. The strongly cemented aggregates were mostly fine-grained gibbsite cemented with additional gibbsite. Dissolution testing was performed on two test samples. One set of tests was performed on large pieces of aggregate solids removed from the heel solids samples. The other set of dissolution tests was performed on a composite sample prepared from well-drained, air-dry heel solids that were crushed to pass a 1/4-in. sieve. The bulk density of the composite sample was 2.04 g/mL. The dissolution tests included water dissolution followed by caustic dissolution testing. In each step of the three-step water dissolution tests, a volume of water approximately equal to 3 times the initial volume of the test solids was added. In each step, the test samples were gently but thoroughly mixed for approximately 2 days at an average ambient temperature of 25 °C. The caustic dissolution tests began with the addition of sufficient 49.6 wt% NaOH to the water dissolution residues to provide ≈3.1 moles of OH for each mole of Al estimated to have been present in the starting composite sample and ≈2.6 moles of OH for each mole of Al potentially present in the starting aggregate sample. Metathesis of gibbsite to sodium aluminate was then allowed to proceed over 10 days of gentle mixing of the

SiC-CMC-Zircaloy-4 Nuclear Fuel Cladding Performance during 4-Point Tubular Bend Testing

Energy Technology Data Exchange (ETDEWEB)

IJ van Rooyen; WR Lloyd; TL Trowbridge; SR Novascone; KM Wendt; SM Bragg-Sitton

2013-09-01

The U.S. Department of Energy Office of Nuclear Energy (DOE NE) established the Light Water Reactor Sustainability (LWRS) program to develop technologies and other solutions to improve the reliability, sustain the safety, and extend the life of current reactors. The Advanced LWR Nuclear Fuel Development Pathway in the LWRS program encompasses strategic research focused on improving reactor core economics and safety margins through the development of an advanced fuel cladding system. Recent investigations of potential options for “accident tolerant” nuclear fuel systems point to the potential benefits of silicon carbide (SiC) cladding. One of the proposed SiC-based fuel cladding designs being investigated incorporates a SiC ceramic matrix composite (CMC) as a structural material supplementing an internal Zircaloy-4 (Zr-4) liner tube, referred to as the hybrid clad design. Characterization of the advanced cladding designs will include a number of out-of-pile (nonnuclear) tests, followed by in-pile irradiation testing of the most promising designs. One of the out-of-pile characterization tests provides measurement of the mechanical properties of the cladding tube using four point bend testing. Although the material properties of the different subsystems (materials) will be determined separately, in this paper we present results of 4-point bending tests performed on fully assembled hybrid cladding tube mock-ups, an assembled Zr-4 cladding tube mock-up as a standard and initial testing results on bare SiC-CMC sleeves to assist in defining design parameters. The hybrid mock-up samples incorporated SiC-CMC sleeves fabricated with 7 polymer impregnation and pyrolysis (PIP) cycles. To provide comparative information; both 1- and 2-ply braided SiC-CMC sleeves were used in this development study. Preliminary stress simulations were performed using the BISON nuclear fuel performance code to show the stress distribution differences for varying lengths between loading points

Plakophilin-2 c.419C>T and risk of heart failure and arrhythmias in the general population

DEFF Research Database (Denmark)

Christensen, Alex Hørby; Kamstrup, Pia Rørbœk; Gandjbakhch, Estelle

2016-01-01

A rare genetic variant in the desmosomal gene plakophilin-2 (PKP2) c.419C>T(p.(S140F)) has repeatedly been identified in patients with dilated cardiomyopathy (DCM) and arrhythmogenic right ventricular cardiomyopathy (ARVC). Whether this is a disease-causing variant remains highly controversial. We...... ratios as a function of c.419C>T genotype were 2.11 (0.50-8.99) for ARVC, 0.72 (0.16-3.28) for hypertrophic cardiomyopathy (HCM)/DCM, and 1.28 (0.46-3.54) for end points combined. Third, in in vitro studies cellular localization of plakophilin-2, plakoglobin, connexin-43, or N-cadherin were similar...... in cells transfected with wild-type or mutant plakophilin-2. In conclusion, combining epidemiological data, with data on patients referred for genetic testing for ARVC or HCM/DCM, and data from in vitro studies, PKP2 c.419C>T did not associate with heart failure, arrhythmias, or premature death, with ARVC...

Comparative neuropharmacology of N-(2-methoxybenzyl)-2,5-dimethoxyphenethylamine (NBOMe) hallucinogens and their 2C counterparts in male rats.

Science.gov (United States)

Elmore, Joshua S; Decker, Ann M; Sulima, Agnieszka; Rice, Kenner C; Partilla, John S; Blough, Bruce E; Baumann, Michael H

2018-03-01

2,5-Dimethoxyphenethylamines (2C compounds) are 5-HT 2A/2C receptor agonists that induce hallucinogenic effects. N-methoxybenzylation of 2C compounds markedly increases their affinity for 5-HT 2A receptors, and two such analogs, 2-(4-chloro-2,5-dimethoxyphenyl)-N-[(2-methoxyphenyl)methyl]ethanamine (25C-NBOMe) and 2-(4-iodo-2,5-dimethoxyphenyl)-N-[(2-methoxyphenyl)methyl]ethanamine (25I-NBOMe), have emerged in recreational drug markets. Here, we investigated the neuropharmacology of 25C-NBOMe and 25I-NBOMe in rats, as compared to their 2C analogs and the prototypical 5-HT 2A/2C agonist 1-(4-iodo-2,5-dimethoxyphenyl)propan-2-amine (DOI). Compounds were tested in vitro using 5-HT 2A receptor binding and calcium mobilization assays. For in vivo experiments, 25C-NBOMe (0.01-0.3 mg/kg), 25I-NBOMe (0.01-0.3 mg/kg), 2-(4-chloro-2,5-dimethoxyphenyl)ethanamine (2C-C) (0.1-3.0 mg/kg), 2-(4-iodo-2,5-dimethoxyphenyl)ethanamine (2C-I) (0.1-3.0 mg/kg) and DOI (0.03-1.0 mg/kg) were administered subcutaneously (sc) to male rats, and 5-HT 2A -mediated behaviors were assessed. NBOMes displayed higher affinity for 5-HT 2A receptors than their 2C counterparts but were substantially weaker in functional assays. 25C-NBOMe and 25I-NBOMe were much more potent at inducing wet dog shakes (WDS) and back muscle contractions (BMC) when compared to 2C-C and 2C-I. Pretreatment with the selective 5-HT 2A antagonist (R)-(2,3-dimethoxyphenyl){1-[2-(4-fluorophenyl)ethyl]-4-piperidinyl}methanol (M100907) reversed behaviors produced by all agonists. Interestingly, binding affinities at the 5-HT 2A receptor were significantly correlated with potencies to induce BMC but not WDS. Our findings show that NBOMes are highly potent 5-HT 2A agonists in rats, similar to effects in mice, and consistent with the reported hallucinogenic effects in human users. Copyright © 2018. Published by Elsevier Ltd.

Effect of fenbendazole on three behavioral tests in male C57BL/6N mice.

Science.gov (United States)

Gadad, Bharathi S; Daher, João P L; Hutchinson, Eric K; Brayton, Cory F; Dawson, Ted M; Pletnikov, Mikhail V; Watson, Julie

2010-11-01

Pinworms are highly contagious parasites of laboratory rodents that often are treated with fenbendazole. To our knowledge, the effect of fenbendazole at therapeutic dosages on behavioral tests in mice has not been evaluated. Here we studied 6-wk-old male C57BL/6N mice. We compared the behavior of control mice (fed regular diet) with 3 groups of mice treated with dietary fenbendazole. Treatment groups were 4 wk of fenbendazole, 2 wk of fenbendazole followed by 2 wk of regular diet, and 2 wk of regular diet followed by 2 wk of fenbendazole. At the end of dietary treatment all groups were tested by open field for central, peripheral and vertical activity; elevated plus maze for anxiety; and rotarod for motor ability and then evaluated by clinical pathology and selected histopathology. Treated and control groups showed no differences in open field or elevated plus maze testing, histopathology, or clinical pathology. However mice treated for 4 wk with fenbendazole or 2 wk of fenbendazole followed by 2 wk regular diet stayed on the rotarod for shorter periods than did controls, and mice treated with 2 wk of regular diet followed by 2 wk fenbendazole showed a trend toward shorter rotarod times. In light of this study, we suggest that open field and elevated plus maze testing is unlikely to be affected by 4 wk fenbendazole treatment in male C57BL/6 mice; however, behavioral tests of motor ability such as rotarod tests may be affected during and for at least 2 wk after fenbendazole treatment.

In-situ fabrication of MoSi{sub 2}/SiC–Mo{sub 2}C gradient anti-oxidation coating on Mo substrate and the crucial effect of Mo{sub 2}C barrier layer at high temperature

Energy Technology Data Exchange (ETDEWEB)

Liu, Jun [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); State Key Laboratory of New Ceramics and Fine Processing, Beijing 100084 (China); Gong, Qianming, E-mail: gongqianming@mail.tsinghua.edu.cn [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); State Key Laboratory of New Ceramics and Fine Processing, Beijing 100084 (China); Shao, Yang; Zhuang, Daming [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); State Key Laboratory of New Ceramics and Fine Processing, Beijing 100084 (China); Liang, Ji [Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

2014-07-01

MoSi{sub 2}/SiC–Mo{sub 2}C gradient coating on molybdenum was in situ prepared with pack cementation process by two steps: (1) carburizing with graphite powder to obtain a Mo{sub 2}C layer on Mo substrate, and (2) siliconizing with Si powder to get a composite MoSi{sub 2}/SiC layer on the upper part of Mo{sub 2}C layer. The microstructure and elemental distribution in the coating were investigated with scanning electron microscopy (SEM), backscattered electron (BSE), energy dispersive spectroscopy (EDS), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). Cyclic oxidation tests (at 500 °C, 1200 °C, 1400 °C and 1600 °C) demonstrated excellent oxidation resistance for the gradient composite coating and the mass loss was only 0.23% in 60 min at 1600 °C. XRD, EPMA, thermal dynamic and phase diagram analyses indicated that the Mo{sub 2}C barrier layer played the key role in slowing down the diffusion of C and Si toward inner Mo substrate at high temperature and principally this contributed to the excellent anti-oxidation for Mo besides the outer MoSi{sub 2}/SiC composite layer.

Film Cooled Recession of SiC/SiC Ceramic Matrix Composites: Test Development, CFD Modeling and Experimental Observations

Science.gov (United States)

Zhu, Dongming; Sakowski, Barbara A.; Fisher, Caleb

2014-01-01

SiCSiC ceramic matrix composites (CMCs) systems will play a crucial role in next generation turbine engines for hot-section component applications because of their ability to significantly increase engine operating temperatures, reduce engine weight and cooling requirements. However, the environmental stability of Si-based ceramics in high pressure, high velocity turbine engine combustion environment is of major concern. The water vapor containing combustion gas leads to accelerated oxidation and corrosion of the SiC based ceramics due to the water vapor reactions with silica (SiO2) scales forming non-protective volatile hydroxide species, resulting in recession of the ceramic components. Although environmental barrier coatings are being developed to help protect the CMC components, there is a need to better understand the fundamental recession behavior of in more realistic cooled engine component environments.In this paper, we describe a comprehensive film cooled high pressure burner rig based testing approach, by using standardized film cooled SiCSiC disc test specimen configurations. The SiCSiC specimens were designed for implementing the burner rig testing in turbine engine relevant combustion environments, obtaining generic film cooled recession rate data under the combustion water vapor conditions, and helping developing the Computational Fluid Dynamics (CFD) film cooled models and performing model validation. Factors affecting the film cooled recession such as temperature, water vapor concentration, combustion gas velocity, and pressure are particularly investigated and modeled, and compared with impingement cooling only recession data in similar combustion flow environments. The experimental and modeling work will help predict the SiCSiC CMC recession behavior, and developing durable CMC systems in complex turbine engine operating conditions.

Preliminary hydrogeologic assessment of boreholes UE-25c No. 1, UE-25c No. 2, and UE-25c No. 3, Yucca Mountain, Nye County, Nevada; Water-resources investigations report 92-4016

Energy Technology Data Exchange (ETDEWEB)

Geldon, A.L.

1993-12-31

The purpose of this report is to characterize the hydrogeology of saturated tuffaceous rocks penetrated by boreholes UE-25c No. 1, UE-25c No.2, and UE-25c No. 3. These boreholes are referred to collectively in this report as the C-holes. The C-holes were drilled to perform multiwell aquifer tests and tracer tests; they comprise the only complex of closely spaced boreholes completed in the saturated zone at Yucca Mountain. Results of lithologic and geophysical logging, fracture analyses, water-level monitoring, temperature and tracejector surveys, aquifer tests, and hydrochemical sampling completed at the C-hole complex as of 1986 are assessed with respect to the regional geologic and hydrologic setting. A conceptual hydrogeological model of the Yucca Mountain area is presented to provide a context for quantitatively evaluating hydrologic tests performed at the C-hole complex as of 1985, for planning and interpreting additional hydrologic tests at the C-hole complex, and for possibly re-evaluating hydrologic tests in boreholes other than the C-holes.

Apoptosis in differentiating C2C12 muscle cells selectively targets Bcl-2-deficient myotubes

Science.gov (United States)

Schoneich, Christian; Dremina, Elena; Galeva, Nadezhda; Sharov, Victor

2014-01-01

Muscle cell apoptosis accompanies normal muscle development and regeneration, as well as degenerative diseases and aging. C2C12 murine myoblast cells represent a common model to study muscle differentiation. Though it was already shown that myogenic differentiation of C2C12 cells is accompanied by enhanced apoptosis in a fraction of cells, either the cell population sensitive to apoptosis or regulatory mechanisms for the apoptotic response are unclear so far. In the current study we characterize apoptotic phenotypes of different types of C2C12 cells at all stages of differentiation, and report here that myotubes of differentiated C2C12 cells with low levels of anti-apoptotic Bcl-2 expression are particularly vulnerable to apoptosis even though they are displaying low levels of pro-apoptotic proteins Bax, Bak and Bad. In contrast, reserve cells exhibit higher levels of Bcl-2 and high resistance to apoptosis. The transfection of proliferating myoblasts with Bcl-2 prior to differentiation did not protect against spontaneous apoptosis accompanying differentiation of C2C12 cell but led to Bcl-2 overexpression in myotubes and to significant protection from apoptotic cell loss caused by exposure to hydrogen peroxide. Overall, our data advocate for a Bcl-2-dependent mechanism of apoptosis in differentiated muscle cells. However, downstream processes for spontaneous and hydrogen peroxide induced apoptosis are not completely similar. Apoptosis in differentiating myoblasts and myotubes is regulated not through interaction of Bcl-2 with pro-apoptotic Bcl-2 family proteins such as Bax, Bak, and Bad. PMID:24129924

Synthesis of 14C analogue of 1,2-diaryl-[2-14C]-pyrroles

International Nuclear Information System (INIS)

Saemian, N.; Shirvani, G.; Matloubi, H.

2007-01-01

Three 1,2-diaryl pyrroles selective COX-2 inhibitors, 2-(4-fluorophenyl)-5-methyl-1-(4-methylsulfonyl-phenyl)-1H pyrrole, 2-(4-fluorophenyl)-1- [4-(methylsulfonyl) phenyl]-1H-pyrrole and 4-[2-(4-fluorophenyl)-1H-pyrrol-1-yl]benzenesulfon-amide, all three labeled with 14 C in the 2-position were prepared from para-fluoro-benzaldehyde-[carbonyl- 14 C]. (author)

Charge transfer processes in collisions of H+ ions with H2, D2, CO, CO2 CH4, C2H2, C2H6 and C3H8 molecules below 10 keV

International Nuclear Information System (INIS)

Kusakabe, T.; Buenker, R.J.; Kimura, M.

2002-01-01

Charge transfer processes resulting from collisions of H + ions with H 2 , D 2 , CO, CO 2 CH 4 , C 2 H 2 , C 2 H 6 and C 3 H 8 molecules have been investigated in the energy range of 0.2 to 4.0 keV experimentally and theoretically. The initial growth rate method was employed in the experiment for studying the dynamics and cross sections. Theoretical analysis based on a molecular-orbital expansion method for H 2 , D 2 , CO, CH 4 and C 2 H 2 targets was also carried out. The present results for the H 2 , CO and CO 2 molecules by H + impact are found to be in excellent accord with most of previous measurements above 1 keV, but they show some differences below this energy where our result displays a stronger energy-dependence. For CH 4 , C 2 H 2 , C 2 H 6 and C 3 H 8 targets, both experimental and theoretical results indicate that if one assumes vibrationally excited molecular ions (CH 4 + , C 2 H 2 + , C 2 H 6 + and C 3 H 8 + ) formed in the exit channel, then charge transfer processes sometimes become more favorable since these vibrationally excited fragments meet an accidental resonant condition. This is a clear indication of the role of vibrational excited states for charge transfer, and is an important realization for general understanding. (author)

Performance tests of a full scale prototype of the Belle II TOP counter with cosmic muons and 2.1 GeV/c positron beam

Energy Technology Data Exchange (ETDEWEB)

Hayakawa, Tomokatsu

2014-12-01

A time-of-propagation detector named TOP is a hadronic particle identification system for the Belle II experiment. We have produced a full scale prototype of the Belle II TOP counter and tested with cosmic muons at KEK and the 2.1 GeV/c positrons at SPring-8 LEPS beamline. The procedures for the quartz acceptance test and assembly worked well and the first quartz radiator was successfully fabricated. The obtained test data shows good agreement with Monte Carlo expectation. - Highlights: • We have successfully produced a full scale prototype of the Belle II TOP counter. • The prototype counter has been tested at KEK and SPring-8 LEPS beamline. • The obtained test data shows good agreement with Monte Carlo expectation.

Vitamin C-linker-conjugated tripeptide AHK stimulates BMP-2-induced osteogenic differentiation of mouse myoblast C2C12 cells.

Science.gov (United States)

Jung, Jung-Il; Park, Kyeong-Yong; Lee, Yura; Park, Mira; Kim, Jiyeon

2018-03-15

Vitamin C-linker-conjugated Ala-His-Lys tripeptide (Vit C-AHK) is a derivative of Vitamin C-conjugated tripeptides, which were originally developed as a component of a product for collagen synthesis enhancement or human dermal fibroblast growth. Here, we investigated the effect of Vit C-AHK on bone morphogenetic protein (BMP)-2-induced osteoblast differentiation in a cell culture model. Vit C-AHK enhanced proliferation of C2C12 cells and induction of BMP-2-induced alkaline phosphatase, a typical marker of osteoblast differentiation. Vit C-AHK also stimulated the phosphorylation and translocation of Smad1/5/8 to the nucleus and phosphorylation of mitogen-activated protein kinases (MAPKs) including ERK1/2 and p38. In addition, Vit C-AHK enhanced the BMP-2-induced mRNA expression of osteoblast differentiation-related genes such as ALP, BMP-2, Osteocalcin, and Runx2. Our results suggest that Vit C-AHK exerts an enhancing effect on osteoblast proliferation and differentiation through activation of Smad1/5/8 and MAPK ERK1/2 and p38 signaling and without significant cytotoxicity. These results provide important data for the development of peptide-based bone-regenerative agents and treatment of bone-related disorders. Copyright © 2018 International Society of Differentiation. Published by Elsevier B.V. All rights reserved.

Testing Gyrokinetics on C-Mod and NSTX

International Nuclear Information System (INIS)

Redi, M.H.; Dorland, W.; Fiore, C.L.; Stutman, D.; Baumgaertel, J.A.; Davis, B.; Kaye, S.M.; McCune, D.C.; Menard, J.; Rewoldt, G.

2005-01-01

Quantitative benchmarks of computational physics codes against experiment are essential for the credible application of such codes. Fluctuation measurements can provide necessary critical tests of nonlinear gyrokinetic simulations, but such require extraordinary computational resources. Linear micro-stability calculations with the GS2 [1] gyrokinetic code have been carried out for tokamak and ST experiments which exhibit internal transport barriers (ITB) and good plasma confinement. Qualitative correlation is found for improved confinement before and during ITB plasmas on Alcator C-Mod [2] and NSTX [3], with weaker long wavelength micro-instabilities in the plasma core regions. Mixing length transport models are discussed. The NSTX L-mode is found to be near marginal stability for kinetic ballooning modes. Fully electromagnetic, linear, gyrokinetic calculations of the Alcator C-Mod ITB during off-axis rf heating, following four plasma species and including the complete electron response show ITG/TEM microturbulence is suppressed in the plasma core and in the barrier region before barrier formation, without recourse to the usual requirements of velocity shear or reversed magnetic shear [4-5]. No strongly growing long or short wavelength drift modes are found in the plasma core but strong ITG/TEM and ETG drift wave turbulence is found outside the barrier region. Linear microstability analysis is qualitatively consistent with the experimental transport analysis, showing low transport inside and high transport outside the ITB region before barrier formation, without consideration of ExB shear stabilization

Effect of alcohol consumption on the liver detoxication capacity as measured by [13C]methacetin- and [methyl-13C]methionine-breath tests.

Science.gov (United States)

Wutzke, Klaus D; Forberger, Anke; Wigger, Marianne

2008-06-01

The aim of this study was to investigate the hepatic microsomal and mitochondrial functions by using the 13CO2-breath test in healthy subjects either before or after the consumption of red wine. Fourteen adults received [13C]methacetin and [methyl-13C]methionine together with a standardised dinner. Expired air samples were taken over 6 h. After a wash-out period, the subjects consumed 0.4 ml ethanol/kg/day together with dinner over a 10-day period. Thereafter, 13C-tracer administration was repeated under identical conditions. The 13CO2-enrichments were measured by isotope ratio mass spectrometry. The mean cumulative percentage 13C-dose recovery (CPDR) after administration of [13C]methacetin and [methyl-13C]methionine either without or with red wine consumption amounted to 38.2+/-6.3 vs. 36.3+/-6.7% (p=0.363) and 9.5+/-3.3 vs. 8.8+/-2.5% (p=0.47), respectively. Moderate alcohol consumption does not induce significant short-term changes of the microsomal and the mitochondrial functions of the human liver in healthy subjects.

CO2 blood test

Science.gov (United States)

Bicarbonate test; HCO3-; Carbon dioxide test; TCO2; Total CO2; CO2 test - serum; Acidosis - CO2; Alkalosis - CO2 ... Many medicines can interfere with blood test results. Your health ... need to stop taking any medicines before you have this test. DO ...

Application of reaction type of C-peptide release test in diabetes mellitus

International Nuclear Information System (INIS)

Chen Dong; Duan Wenruo; He Juan; Lu Zhenfang

2001-01-01

The author is to confirm the effect of C-peptide release test and types of release reaction in appraisal of pancreas function of β-cell and selection of treatment for diabetes mellitus (DM) patients. The serum C-peptide release test of 67 normal controls and 217 DM patients were determined by RIA, and the results were analyzed and compared. C-peptide release test can reflect the pancreas function of β-cell better, the peak of C-peptide ≥ 0.6 nmol/L after lunch can be the limit of whether to reduce the level of blood glucose only by oral drug. The authors should adjust the treatment through analyzing the type of C-peptide release reaction. C-peptide release test is very important in evaluating the pancreas function of β-cell, classifying the type of DM and selecting the treatment

Synthesis of 1-13C-1-indanone and 2-13C-1,2,3,4-tetrahydroquinoline

International Nuclear Information System (INIS)

Pickering, R.E.; Wysocki, M.A.; Eisenbraun, E.J.

1985-01-01

The synthesis of 2- 13 C-1,2,3,4-tetrahydroquinoline (5) via 1- 13 C-3-phenylpropanoic acid (1), 1- 13 C-1-indanone (2), 1- 13 C-1-indanone hydrazone (3) and 2- 13 C-3,4-dihydro-2(1H)-quinolinone (4) proceeded in 78, 96, 95, 79, and 85% individual yields respectively for 1, 2, 3, 4, 5 and 61% overall yield of the latter from 1. (author)

Comparison of revision strategies for failed C2-posterior cervical pedicle screws: a biomechanical study.

Science.gov (United States)

Mayer, Michael; Zenner, Juliane; Bogner, Robert; Hitzl, Wolfgang; Figl, Markus; von Keudell, Arvind; Stephan, Daniel; Penzkofer, Rainer; Augat, Peter; Korn, Gundobert; Resch, Herbert; Koller, Heiko

2013-01-01

With increasing usage within challenging biomechanical constructs, failures of C2 posterior cervical pedicle screws (C2-pCPSs) will occur. The purpose of the study was therefore to investigate the biomechanical characteristics of two revision techniques after the failure of C2-pCPSs. Twelve human C2 vertebrae were tested in vitro in a biomechanical study to compare two strategies for revision screws after failure of C2-pCPSs. C2 pedicles were instrumented using unicortical 3.5-mm CPS bilaterally (Synapse/Synthes, Switzerland). Insertion accuracy was verified by fluoroscopy. C2 vertebrae were potted and fixed in an electromechanical testing machine with the screw axis coaxial to the pullout direction. Pullout testing was conducted with load and displacement data taken continuously. The peak load to failure was measured in newtons (N) and is reported as the pullout resistance (POR). After pullout, two revision strategies were tested in each vertebra. In Group-1, revision was performed with 4.0-mm C2-pCPSs. In Group-2, revision was performed with C2-pedicle bone-plastic combined with the use of a 4-mm C2-pCPSs. For the statistical analysis, the POR between screws was compared using absolute values (N) and the POR of the revision techniques normalized to that of the primary procedures (%). The POR of primary 3.5-mm CPSs was 1,140.5 ± 539.6 N for Group-1 and 1,007.7 ± 362.5 N for Group-2; the difference was not significant. In the revision setting, the POR in Group-1 was 705.8 ± 449.1 N, representing a reduction of 38.1 ± 32.9 % compared with that of primary screw fixation. For Group-2, the POR was 875.3 ± 367.9 N, representing a reduction of 13.1 ± 23.4 %. A statistical analysis showed a significantly higher POR for Group-2 compared with Group-1 (p = 0.02). Although the statistics showed a significantly reduced POR for both revision strategies compared with primary fixation (p plastic, the POR can be significantly increased compared with the use of only an

Hepatitis C Core Antigen Testing for Diagnosis of Hepatitis C Virus Infection: A Systematic Review and Meta-analysis.

Science.gov (United States)

Freiman, J Morgan; Tran, Trang M; Schumacher, Samuel G; White, Laura F; Ongarello, Stefano; Cohn, Jennifer; Easterbrook, Philippa J; Linas, Benjamin P; Denkinger, Claudia M

2016-09-06

Diagnosis of chronic hepatitis C virus (HCV) infection requires both a positive HCV antibody screen and confirmatory nucleic acid testing (NAT). Testing for hepatitis C virus core antigen (HCVcAg) is a potential alternative to NAT. To evaluate the accuracy of diagnosis of active HCV infection among adults and children for 5 HCVcAg tests compared with NAT. EMBASE, PubMed, Web of Science, Scopus, and Cochrane Database of Systematic Reviews from 1990 through 31 March 2016. Case-control, cross-sectional, cohort, or randomized trials that compared any of 5 HCVcAg tests with an NAT reference standard. 2 independent reviewers extracted data and assessed quality using an adapted QUADAS-2 (Quality Assessment of Diagnostic Accuracy Studies 2) tool. 44 studies evaluated 5 index tests. Studies for the Abbott ARCHITECT HCV Ag assay had the highest quality, whereas those for the Ortho HCV Ag enzyme-linked immunosorbent assay (ELISA) had the lowest quality. From bivariate analyses, the sensitivity and specificity of the assays were as follows: Abbott ARCHITECT, 93.4% (95% CI, 90.1% to 96.4%) and 98.8% (CI, 97.4% to 99.5%); Ortho ELISA, 93.2% (CI, 81.6% to 97.7%) and 99.2% (CI, 87.9% to 100%); and Hunan Jynda Bioengineering Group HCV Ag ELISA, 59.5% (CI, 46.0% to 71.7%) and 82.9% (CI, 58.6% to 94.3%). Insufficient data were available for a meta-analysis about the Fujirebio Lumipulse Ortho HCV Ag and Eiken Lumispot HCV Ag assays. In 3 quantitative studies using Abbott ARCHITECT, HCVcAg correlated closely with HCV RNA levels greater than 3000 IU/mL. Insufficient data were available on covariates, such as HIV or hepatitis B virus status, for subgroup analyses. Few studies reported genotypes of isolates, and data for genotypes 4, 5, and 6 were scant. Most studies were conducted in high-resource settings and reference laboratories. The HCVcAg assays with signal amplification have high sensitivity, high specificity, and good correlation with HCV RNA levels greater than 3000 IU/mL and

HbA1c Test as a Tool in the Diagnosis of Gestational Diabetes Mellitus.

Directory of Open Access Journals (Sweden)

Paula Breitenbach Renz

Full Text Available Gestational diabetes mellitus (GDM is a prevalent and potentially serious condition which may put both mothers and neonates at risk. The current recommendation for diagnosis is the oral glucose tolerance test (OGTT. This study aimed to determine the usefulness of HbA1c test as a diagnostic tool for GDM as compared to the traditional criteria based on the OGTT.This was a diagnostic test accuracy study. We performed OGTT and HbA1c test in women attending prenatal visits at a tertiary hospital. GDM was defined according to WHO1999 or ADA/WHO 2013 criteria. ROC curve was used to evaluate the diagnostic performance of HbA1c. Sensitivity, specificity and likelihood ratios for different HbA1c cut-off points were calculated.Of the 262 women in the third trimester of gestation enrolled in the study, 86 (33% were diagnosed with GDM. Only five of these women presented HbA1c ≥48 mmol/mol (6.5%. This cut-off point presented 100% specificity but very low sensitivity (7%. Based on ROC curve, and considering OGTT as the reference criterion, HbA1c ≥40 mmol/mol (5.8% showed adequate specificity in diagnosing GDM (94.9% but low sensitivity (26.4%. Unlike, HbA1c values of 31 mmol/mol (5.0% presented adequate sensitivity (89.7% but low specificity (32.6% to detect GDM. For women with HbA1c ≥40 mmol/mol (5.8%, the positive and negative likelihood ratios were 5.14 (95%CI 2.49-10.63 and 0.78 (0.68-0.88, respectively. The post-test probability of GDM was about 40%, representing a 4.0-fold increase in the mean pre-test probability. This cut-off point could eliminate the need for the unpleasant and laborious OGTT tests in almost one third of cases, as 38% of patients with GDM may be diagnosable by HbA1c test alone.Our results show that combined HbA1c and OGTT measurements may be useful in diagnosing GDM.

Test plan using the HTTR for commercialization of GTHTR300C

International Nuclear Information System (INIS)

Tachibana, Yukio; Sakaba, Nariaki; Ohashi, Hirofumi; Sato, Hiroyuki; Ueta, Shohei; Aihara, Jun; Goto, Minoru; Sumita, Junya; Shibata, Taiju; Takamatsu, Kuniyoshi; Inagaki, Yoshiyuki; Kunitomi, Kazuhiko; Nishihara, Tetsuo; Hamamoto, Shimpei; Iyoku, Tatsuo

2010-02-01

The High Temperature Engineering Test Reactor (HTTR) is the first High Temperature Gas-cooled Reactor (HTGR) built at the Oarai Research and Development Center of JAEA with thermal power of 30 MW and the maximum reactor outlet coolant temperature of 950degC. The HTTR achieved the first criticality in 1998, the reactor outlet coolant temperature of 950degC in 2004, and 30 days continuous operation in 2007. Since 2002, safety demonstration tests including reactivity insertion tests and coolant flow reduction tests have been conducted to show inherent safety features of the HTGRs by using the HTTR. This report describes full scope of the future feasible test plan mainly using the HTTR. The test items cover fuel performance and radionuclide transport, core physics, reactor thermal hydraulics and plant dynamics, and reactor operations, maintenance, control, etc. The test results will be utilized for realization of Japan's commercial Very High Temperature Reactor (VHTR) system, GTHTR300C. (author)

Sc2C2@D3h(14246)-C74: A Missing Piece of the Clusterfullerene Puzzle.

Science.gov (United States)

Wang, Yaofeng; Tang, Qiangqiang; Feng, Lai; Chen, Ning

2017-02-20

Clusterfullerenes with variable carbon cages have been extensively studied in recent years. However, despite all these efforts, C 74 cage-based clusterfullerene remains a missing piece of the puzzle. Herein, we show that single-crystal X-ray crystallographic analysis unambiguously assigns the previously reported dimetallofullerene Sc 2 @C 76 to a novel carbide clusterfullerene, Sc 2 C 2 @D 3h (14246)-C 74 , the first experimentally proven clusterfullerene with a C 74 cage. In addition, Sc 2 C 2 @D 3h (14246)-C 74 was charaterized by mass spectrometry, ultraviolet-visible-near-infrared absorption spectroscopy, 45 Sc nuclear magnetic resonance, and cyclic voltammetry. Comparative studies of the motion of the carbide cluster in Sc 2 C 2 @D 3h (14246)-C 74 and Sc 2 C 2 @C 2n (n = 40-44) revealed that a combination of factors, involving both the shape and size of the cage, is crucial in dictating the cluster motion. Moreover, structural studies of D 3h (14246)-C 74 revealed that it can be easily converted to C s (10528)-C 72 and T d (19151)-C 76 cages via C 2 desertion/insertion and Stone-Wales transformation. This suggests that D 3h (14246)-C 74 might play an important role in the growth pathway of clusterfullerenes.

High expression of ubiquitin-conjugating enzyme 2C (UBE2C) correlates with nasopharyngeal carcinoma progression

International Nuclear Information System (INIS)

Shen, Zhihua; Guo, Junli; Jie, Wei; Jiang, Xiaofan; Zeng, Chao; Zheng, Shaojiang; Luo, Botao; Zeng, Yumei; Ding, Ranran; Jiang, Hanguo; He, Qiyi

2013-01-01

Overexpression of ubiquitin-conjugating enzyme 2C (UBE2C) has been detected in many types of human cancers, and is correlated with tumor malignancy. However, the role of UBE2C in human nasopharyngeal carcinoma (NPC) is unclear. In this study, we investigated the role of aberrant UBE2C expression in the progression of human NPC. Immunohistochemical analysis was performed to detect UBE2C protein in clinical samples of NPC and benign nasopharyngeal tissues, and the association of UBE2C expression with patient clinicopathological characteristics was analyzed. UBEC2 expression profiles were evaluated in cell lines representing varying differentiated stages of NPC and immortalized nasopharyngeal epithelia NP-69 cells using quantitative RT-PCR, western blotting and fluorescent staining. Furthermore, UBE2C was knocked down using RNA interference in these cell lines and proliferation and cell cycle distribution was investigated. Immunohistochemical analysis revealed that UBE2C protein expression levels were higher in NPC tissues than in benign nasopharyngeal tissues (P<0.001). Moreover, high UBE2C protein expression was positively correlated with tumor size (P=0.017), lymph node metastasis (P=0.016) and distant metastasis (P=0.015) in NPC patients. In vitro experiments demonstrated that UBE2C expression levels were inversely correlated with the degree of differentiation of NPC cell lines, whereas UBE2C displayed low level of expression in NP-69 cells. Knockdown of UBE2C led to significant arrest at the S and G2/M phases of the cell cycle, and decreased cell proliferation was observed in poorly-differentiated CNE2Z NPC cells and undifferentiated C666-1 cells, but not in well-differentiated CNE1 and immortalized NP-69 cells. Our findings suggest that high expression of UBE2C in human NPC is closely related to tumor malignancy, and may be a potential marker for NPC progression

Automatic testing technologies for I and C systems for nuclear power plants

International Nuclear Information System (INIS)

Yoshida, Motoko; Sugio, Takayuki; Konishi, Tadao

2014-01-01

With the aim of enhancing the global competitiveness of instrumentation and control (I and C) systems for nuclear power plants, Toshiba has been making efforts to reduce the worker hours required for the testing of such systems and improve the quality of the tests. Display screen tests, which include many routine, repetitive tests and manual tests requiring a large number of operators to monitor multiple screen displays of the I and C system, are an essential element of the testing process. The introduction of automatic testing technologies is expected to substantially improve the efficiency of such display screen tests. We have now developed automatic testing technologies for display screen tests that can be applied without the need to change the I and C system. These technologies contribute to both the reduction of worker hours for testing and improvement of the quality of the tests. (author)

CDC Vital Signs: Hepatitis C: Testing Baby Boomers Saves Lives

Science.gov (United States)

... C antibody is negative, then there is no hepatitis C virus infection and no further action needed. If the blood ... be a follow-up RNA blood test for hepatitis c virus infection. If the RNA is negative, then there is ...

Expression of paired-like homeodomain transcription factor 2c (PITX2c) in epidermal keratinocytes

International Nuclear Information System (INIS)

Shi, Ge; Sohn, Kyung-Cheol; Choi, Tae-Young; Choi, Dae-Kyoung; Lee, Sang-Sin; Ou, Bai-sheng; Kim, Sooil; Lee, Young Ho; Yoon, Tae-Jin; Kim, Seong-Jin; Lee, Young; Seo, Young-Joon; Lee, Jeung-Hoon; Kim, Chang Deok

2010-01-01

Paired-like homeodomain transcription factor 2 (PITX2) has been implicated as one of the genes responsible for Rieger syndrome. It has been also shown to play a central role during development. In this study, we investigated the functional role of PITX2 in keratinocyte differentiation. RT-PCR analysis showed that PITX2c isoform was predominantly expressed in a differentiation-dependent manner. Consistent with, immunohistochemical staining showed that PITX2 expression was increased in the upper layer of epidermis. When PITX2c was overexpressed in cultured keratinocytes by a recombinant adenovirus, the differentiation markers such as involucrin and loricrin were significantly increased at both mRNA and protein levels. In addition, PITX2c overexpression led to the decrease of cell growth, concomitantly with the upregulation of cell cycle-related genes p21. To investigate the effect of PITX2c in vivo, we microinjected PITX2c expression vector into zebrafish embryo. Interestingly, overexpression of PITX2c in zebrafish embryo led to the formation of horn-like structure and thickening of epidermis, together with the increase of keratin 8 (K8) expression. These results suggest that PITX2c has a role in proliferation and differentiation of epidermal keratinocytes.

Expression of paired-like homeodomain transcription factor 2c (PITX2c) in epidermal keratinocytes

Energy Technology Data Exchange (ETDEWEB)

Shi, Ge [Department of Dermatology, School of Medicine, Chungnam National University, Daejeon, 301-747 (Korea, Republic of); Research Institute for Medical Sciences, School of Medicine, Chungnam National University, Daejeon, 301-747 (Korea, Republic of); Department of Dermatology, The First Affiliated Hospital, Guangxi Traditional Chinese Medical University, Guangxi, Nanning, 530023 (China); Sohn, Kyung-Cheol; Choi, Tae-Young; Choi, Dae-Kyoung; Lee, Sang-Sin [Department of Dermatology, School of Medicine, Chungnam National University, Daejeon, 301-747 (Korea, Republic of); Research Institute for Medical Sciences, School of Medicine, Chungnam National University, Daejeon, 301-747 (Korea, Republic of); Ou, Bai-sheng [Department of Dermatology, The First Affiliated Hospital, Guangxi Traditional Chinese Medical University, Guangxi, Nanning, 530023 (China); Kim, Sooil; Lee, Young Ho [Department of Anatomy, School of Medicine, Chungnam National University, Daejeon, 301-747 (Korea, Republic of); Yoon, Tae-Jin [Department of Dermatology, School of Medicine, Gyeongsang National University, Jinju, 660-702 (Korea, Republic of); Institute of Health Sciences, School of Medicine, Gyeongsang National University, Jinju, 660-702 (Korea, Republic of); Kim, Seong-Jin [Department of Dermatology, Chonnam National University Medical School, Gwangju, 501-757 (Korea, Republic of); Lee, Young; Seo, Young-Joon; Lee, Jeung-Hoon [Department of Dermatology, School of Medicine, Chungnam National University, Daejeon, 301-747 (Korea, Republic of); Research Institute for Medical Sciences, School of Medicine, Chungnam National University, Daejeon, 301-747 (Korea, Republic of); Kim, Chang Deok, E-mail: cdkimd@cnu.ac.kr [Department of Dermatology, School of Medicine, Chungnam National University, Daejeon, 301-747 (Korea, Republic of); Research Institute for Medical Sciences, School of Medicine, Chungnam National University, Daejeon, 301-747 (Korea, Republic of)

2010-11-15

Paired-like homeodomain transcription factor 2 (PITX2) has been implicated as one of the genes responsible for Rieger syndrome. It has been also shown to play a central role during development. In this study, we investigated the functional role of PITX2 in keratinocyte differentiation. RT-PCR analysis showed that PITX2c isoform was predominantly expressed in a differentiation-dependent manner. Consistent with, immunohistochemical staining showed that PITX2 expression was increased in the upper layer of epidermis. When PITX2c was overexpressed in cultured keratinocytes by a recombinant adenovirus, the differentiation markers such as involucrin and loricrin were significantly increased at both mRNA and protein levels. In addition, PITX2c overexpression led to the decrease of cell growth, concomitantly with the upregulation of cell cycle-related genes p21. To investigate the effect of PITX2c in vivo, we microinjected PITX2c expression vector into zebrafish embryo. Interestingly, overexpression of PITX2c in zebrafish embryo led to the formation of horn-like structure and thickening of epidermis, together with the increase of keratin 8 (K8) expression. These results suggest that PITX2c has a role in proliferation and differentiation of epidermal keratinocytes.

Turnover of carbon in the 13C-urea breath test for the detection of Helicobacter pylori infection

International Nuclear Information System (INIS)

Costa, Vladimir E.; Andreazzi, Mariana; Cury, Caio S.; Bassetto Junior, Carlos A.Z.; Rodrigues, Maria A.M.; Ducatti, Carlos

2013-01-01

To obtain a standard protocol for the application of 13 C-urea breath test ( 13 C-UBT) analyzed by Isotope Ratio Mass Spectrometer (IRMS) to detect helicobacter pylori infection in the population is necessary to know the behavior of the turnover of 13 C during the test in different individuals. The aims of this study was to find out a pattern for the turnover of the 13 C in the 13 C-UBT, analyzed by IRMS, in patients infected with H. pylori, in a Brazilian population, to define a protocol test application. We found that the isotopic ratio 13 C/ 12 C in expired CO 2 from patients infected with H. pylori and subjected to 13 C-UBT does not follow a single pattern of behavior. However this behavior can be similar in subjects having the same maximum values following an inverse proportional relationship between the maximum value and the time of appearance in the curve. (author)

Interpretation of non-invasive breath tests using 13C-labeled substrates - a preliminary report with 13C-methacetin

Directory of Open Access Journals (Sweden)

Lock JF

2009-12-01

Full Text Available Abstract Non-invasive breath tests can serve as valuable diagnostic tools in medicine as they can determine particular enzymatic and metabolic functions in vivo. However, methodological pitfalls have limited the actual clinical application of those tests till today. A major challenge of non-invasive breath tests has remained the provision of individually reliable test results. To overcome these limitations, a better understanding of breath kinetics during non-invasive breaths tests is essential. This analysis compares the breath recovery of a 13C-methacetin breath test with the actual serum kinetics of the substrate. It is shown, that breath and serum kinetics of the same test are significantly different over a period of 60 minutes. The recovery of the tracer 13CO2 in breath seems to be significantly delayed due to intermediate storage in the bicarbonate pool. This has to be taken into account for the application of non-invasive breath test protocols. Otherwise, breath tests might display bicarbonate kinetics despite the metabolic capacity of the particular target enzyme.

Can the C-14 urea breath test reflect the extent and degree of ongoing helicobacter pylori infection

International Nuclear Information System (INIS)

Lim, Seok Tae; Sohn, Myung Hee; Lee, Seung Ok; Lee, Soo Taik; Jeong, Myung Ja

2001-01-01

The C-14 urea breath test (C-14 UBT) is the most specific noninvasive method to detect Helicobacter (H) pylori infection. We investigated if the C-14 UBT can reflect the presence and degree of H. pylori detected by gastroduodenoscopic biopsies (GBx). One hundred fifty patients (M:F=83:67,age 48.6±11.2 yrs) underwent C-14 UBT, rapid urease test (CLO test) and GBx on the same day. For the C-14 UBT, a single breath sample was collected at 10 minutes after ingestion of C-14 urea (137 KBq) capsule and counting was done in a liquid scintillation counter for 1 minute, and the results were classified as positive (≥200 dpm), intermediate ( 50 ∼ 199 dpm) or negative ( < 50 dpm). The results of CLO tests were classified as positive or negative according to color change. The results of GBx on giemsa stain were graded 0 (normal) to 4(diffuse) according to the distribution of H. pylori by the Wyatt method. We compared C-14 UBT results with GBx grade as a gold standard. In the assessment of the presence of H. pylori infection, the C-14 UBT global performance yielded sensitivity, specificity, positive predictive value (PPV), negative predictive value (NPV) and accuracy of 92.5%, 88.4%, 97.1%, 88.4% and 91.3%, respectively. However, the CLO test had sensitivity, specificity, PPV, NPV and accuracy of 83.2%, 81.4%, 91.8%, 81.4% and 82.7%, respectively. The quantitative values of the C-14 UBT were 45 ± 27 dpm in grade 0, 707 ±584 dpm in grade 1, 1558±584 dpm in grade 2, 1851±604 dpm in grade 3, and 2719 ± 892 dpm in grade 4. A significant correlation (r=0.848, p<0.01) was found between C-14 UBT and the grade of distribution of H. pylori infection on GBx with giemsa stain. We conclude that the C-14 UBT is a highly accurate, simple and noninvasive method for the diagnosis of ongoing H. pylori infection and reflects the degree of bacterial distribution

Formation and early hydration characteristics of C2.75B1.25A3$ in binary system of C2.75B1.25A3$-C2S

Directory of Open Access Journals (Sweden)

Wang, Shoude

2016-09-01

Full Text Available C2.75B1.25A3$ (2.75CaO•1.25BaO• 3Al2O3• SO3 is one of the important minerals and it govern-directly the early-strength of belite-barium calcium sulphoaluminate cement. In this paper a binary system C2.75B1.25A3$-C2S is selected to investigate the formation of C2.75B1.25A3$. In the range of 1100 °C–1200 °C, the earlier formed C2S hinders the formation of C2.75B1.25A3$. On the contrary, when the temperature is in the range of 1200 °C–1350 °C, the initially formed C2S could provide a surface for the nucleation of C2.75B1.25A3$ and cut down the potential barrier (?Gk* for the heterogeneous nucleation of C2.75B1.25A3$, which contributes to its formation. Moreover, at 1350 °C, the large amount of previously formed C2S benefits the extent of formation of C2.75B1.25A3$. The possible reason was that it could prevent sulfur evaporation. In early hydration age, AFm and AFt originating from C2.75B1.25A3$ hydration are found within 2 h and 12 h under 95% RH at 1 °C, respectively, whereas C2S is unhydrated at this moment.En el cemento de sulfoaluminato de calcio y bario, el C2.75B1.25A3$ (2.75CaO•1.25BaO• 3Al2 O3• SO3 es una de las principales fases, y regula directamente la resistencia inicial del cemento. En este trabajo, se ha seleccionado el sistema binario C2.75B1.25A3$-C2S para investigar la formación de C2.75B1.25A3$. En el rango de 1100 °C-1200 °C, el C2S formado anteriormente impide la formación de C2.75B1.25A3$, mientras que cuando la temperatura está entre 1200 °C-1350 °C, el C2S proporcionaría una superficie de nucleación de C2.75B1.25A3$ reduciendo la barrera de potencial (?Gk* para la nucleación heterogénea de C2.75B1.25A3$, lo que contribuye a su formación. Además, a 1350 °C, la gran cantidad de C2S formado beneficia la formación de C2.75B1.25A3$, ya que podía prevenir la evaporación del azufre. En las primeras etapas de la hidratación (entre 2 y 12h y 95% HR a 1 ºC se pueden encontrar AFM y AFt

Overview of C-2U FRC Experimental Program and Plans for C-2W

Science.gov (United States)

Gota, H.; Binderbauer, M. W.; Tajima, T.; Putvinski, S.; Tuszewski, M.; Dettrick, S.; Korepanov, S.; Smirnov, A.; Thompson, M. C.; Yang, X.; Cappello, M.; Ivanov, A. A.; TAE Team

2016-10-01

Tri Alpha Energy's experimental program has been focused on a demonstration of reliable field-reversed configuration (FRC) formation and sustainment, driven by fast ions via high-power neutral-beam (NB) injection. The world's largest compact-toroid experimental devices, C-2 and C-2U, have successfully produced a well-stabilized, sustainable FRC plasma state with NB injection (input power, PNB 10 + MW; 15 keV hydrogen) and end-on coaxial plasma guns. Remarkable improvements in confinement and stability of FRC plasmas have led to further improved fast-ion build up; thereby, an advanced beam-driven FRC state has been produced and sustained for up to 5 + ms (longer than all characteristic system time scales), only limited by hardware and electric supply constraints such as NB and plasma-gun power supplies. To further improve the FRC performance the C-2U device is being replaced by C-2W featuring higher injected NB power, longer pulse duration as well as enhanced edge-biasing systems and substantially upgraded divertors. Main C-2U experimental results and key features of C-2W will be presented. Tri Alpha Energy, Inc.

Circumferential tensile test method for mechanical property evaluation of SiC/SiC tube

Energy Technology Data Exchange (ETDEWEB)

Yu, Ju-Hyeon, E-mail: 15096018@mmm.muroran-it.ac.jp [Graduate School, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Kishimoto, Hirotatsu [Graduate School, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); OASIS, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Park, Joon-soo [OASIS, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Nakazato, Naofumi [Graduate School, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Kohyama, Akira [OASIS, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan)

2016-11-01

Highlights: • NITE SiC/SiC cooling channel system to be a candidate of divertor system in future. • Hoop strength is one of the important factors for a tube. • This research studies the relationship between deformation and strain of SiC/SiC tube. - Abstract: SiC fiber reinforced/SiC matrix (SiC/SiC) composite is expected to be a candidate material for the first-wall, components in the blanket and divertor of fusion reactors in future. In such components, SiC/SiC composites need to be formed to be various shapes. SiC/SiC tubes has been expected to be employed for blanket and divertor after DEMO reactor, but there is not established mechanical investigation technique. Recent progress of SiC/SiC processing techniques is likely to realize strong, having gas tightness SiC/SiC tubes which will contribute for the development of fusion reactors. This research studies the relationship between deformation and strain of SiC/SiC tube using a circumferential tensile test method to establish a mechanical property investigation method of SiC/SiC tubes.

Evaluation report on CCTF Core-I reflood tests C1-5 (Run 14), C1-7 (Run 16) and C1-14 (Run 23)

International Nuclear Information System (INIS)

Sugimoto, Jun; Muurao, Yoshio

1983-02-01

The present report describes the effects of the initial clad temperature on the reflood phenomena observed in the Cylindrical Core Test Facility (CCTF) at Japan Atomic Energy Research Institute. The evaluation is based on the data of tests C1-5, C1-7 and C1-14 of the CCTF-Core I test series. Nominal initial peak clad temperatures in these tests are 600 0 C, 700 0 C and 800 0 C, respectively. With the higher initial clad temperature, the higher loop mass flow rate and the lower water accumulation in the core and the upper plenum were obtained in an early reflood transient. However, the core inlet flow conditions, which is sensitive to the core cooling, were not much affected by the higher initial clad temperature. The slower quench front propagation was observed with the higher initial clad temperature. However, the heat transfer coefficient was almost identical with each other before the turnaround time, which resulted in the lower temperature rise with the highest initial clad temperature. This qualitatively agreed with the results of the forced feed FLECHT experiment. (author)

Copper nanoparticle ensembles for selective electroreduction of CO2 to C2–C3 products

Science.gov (United States)

Kley, Christopher S.; Li, Yifan; Yang, Peidong

2017-01-01

Direct conversion of carbon dioxide to multicarbon products remains as a grand challenge in electrochemical CO2 reduction. Various forms of oxidized copper have been demonstrated as electrocatalysts that still require large overpotentials. Here, we show that an ensemble of Cu nanoparticles (NPs) enables selective formation of C2–C3 products at low overpotentials. Densely packed Cu NP ensembles underwent structural transformation during electrolysis into electrocatalytically active cube-like particles intermixed with smaller nanoparticles. Ethylene, ethanol, and n-propanol are the major C2–C3 products with onset potential at −0.53 V (vs. reversible hydrogen electrode, RHE) and C2–C3 faradaic efficiency (FE) reaching 50% at only −0.75 V. Thus, the catalyst exhibits selective generation of C2–C3 hydrocarbons and oxygenates at considerably lowered overpotentials in neutral pH aqueous media. In addition, this approach suggests new opportunities in realizing multicarbon product formation from CO2, where the majority of efforts has been to use oxidized copper-based materials. Robust catalytic performance is demonstrated by 10 h of stable operation with C2–C3 current density 10 mA/cm2 (at −0.75 V), rendering it attractive for solar-to-fuel applications. Tafel analysis suggests reductive CO coupling as a rate determining step for C2 products, while n-propanol (C3) production seems to have a discrete pathway. PMID:28923930

[*C]octanoic acid breath test to measure gastric emptying rate of solids.

Science.gov (United States)

Maes, B D; Ghoos, Y F; Rutgeerts, P J; Hiele, M I; Geypens, B; Vantrappen, G

1994-12-01

We have developed a breath test to measure solid gastric emptying using a standardized scrambled egg test meal (250 kcal) labeled with [14C]octanoic acid or [13C]octanoic acid. In vitro incubation studies showed that octanoic acid is a reliable marker of the solid phase. The breath test was validated in 36 subjects by simultaneous radioscintigraphic and breath test measurements. Nine healthy volunteers were studied after intravenous administration of 200 mg erythromycin and peroral administration of 30 mg propantheline, respectively. Erythromycin significantly enhanced gastric emptying, while propantheline significantly reduced gastric emptying rates. We conclude that the [*C]octanoic breath test is a promising and reliable test for measuring the gastric emptying rate of solids.

Alkali/TX{sub 2} catalysts for CO/H{sub 2} conversion to C{sub 1}-C{sub 4} alcohols. Technical progress report, March 1989--August 1989

Energy Technology Data Exchange (ETDEWEB)

Klier, K.; Herman, R.G.; Bastian, R.D.; Flanagan, K.L.

1989-12-31

Ruthenium disulfide catalysts have been synthesized, tested, and characterized during this period of research. It was observed that both the undoped and Cs-doped RuS{sub 2} catalysts produced alcohols and lower amounts of hydrocarbons from H{sub 2}/CO = 1.0 synthesis gas at temperatures above 300{degree}C. Calcination and catalytic testing resulted in partial reduction of the RuS{sub 2} to Ru{sup o}. Calcination under H{sub 2}S prevented the partial reduction of the RuS{sub 2} catalyst, but subsequent catalytic testing again resulted in the formation of a quantity of Ru{sup o}. A Cs-doped RuS{sub 2} catalyst was prepared, but it might have had too high of a loading of Cs. Upon testing, a lower activity was observed for the doped catalyst compared with the undoped catalyst, but the alcohol selectivity was the same for the two catalysts.

Forward $\\pi^{+-}$ production in p-$O_2$ and p-$N_2$ interactions at 12 GeV/c

CERN Document Server

Catanesi, M.G.; Edgecock, R.; Ellis, M.; Gossling, C.; Bunyatov, S.; Krasnoperov, A.; Popov, B.; Tereschenko, V.; Di Capua, E.; Vidal-Sitjes, G.; Artamonov, A.; Giani, S.; Gilardoni, S.; Gorbunov, P.; Grant, A.; Grossheim, A.; Ivanchenko, A.; Ivanchenko, V.; Kayis-Topaksu, A.; Panman, J.; Papadopoulos, I.; Tcherniaev, E.; Tsukerman, I.; Wiebusch, C.; Zucchelli, P.; Blondel, A.; Borghi, S.; Morone, M.C.; Prior, G.; Schroeter, R.; Meurer, C.; Gastaldi, U.; Mills, G.B.; Graulich, J.S.; Gregoire, G.; Bonesini, M.; Ferri, F.; Kirsanov, M.; Bagulya, A.; Grichine, V.; Polukhina, N.; Palladino, V.; Coney, L.; Schmitz, D.; Barr, G.; Bobisut, F.; Gibin, D.; Guglielmi, A.; Mezzetto, M.; Dumarchez, J.; Dore, U.; Orestano, D.; Pastore, F.; Tonazzo, A.; Tortora, L.; Booth, C.; Howlett, L.; Bogomilov, M.; Kolev, D.; Tsenov, R.; Piperov, Stefan; Temnikov, P.; Apollonio, M.; Chimenti, P.; Giannini, G.; Burguet-Castell, J.; Cervera-Villanueva, A.; Gomez-Cadenas, J.J.; Martin-Albo, J.; Sorel, M.

2008-01-01

Measurements of double-differential charged pion production cross-sections in interactions of 12 GeV/c protons on O_2 and N_2 thin targets are presented in the kinematic range 0.5 GeV/c < p_{\\pi} < 8 GeV/c and 50 mrad < \\theta_{\\pi} < 250 mrad (in the laboratory frame) and are compared with p--C results. For p--N_2 (p--O_2) interactions the analysis is performed using 38576 (7522) reconstructed secondary pions. The analysis uses the beam instrumentation and the forward spectrometer of the HARP experiment at CERN PS. The measured cross-sections have a direct impact on the precise calculation of atmospheric neutrino fluxes and on the improved reliability of extensive air shower simulations by reducing the uncertainties of hadronic interaction models in the low energy range. In particular, the present results allow the common hypothesis that p--C data can be used to predict the p--N_2 and p--O_2 pion production cross-sections to be tested.

A comparison C1-C2 transarticular screw placement after self-education and mentored education of orthopaedic residents.

Science.gov (United States)

Kirkpatrick, John S

2012-08-01

Prospective randomized trial. This study will provide preliminary data on whether residents can be "self-taught" and to what extent a lecture, demonstration, and coaching can improve skills and knowledge. Practice-based learning is an essential competency in Accreditation Council for graduate Medical Education-accredited residencies. Little has been done to demonstrate whether residents can be self-taught or benefit from mentoring in understanding and performing difficult surgical tasks. A written test was given to orthopedic residents on C1-C2 transarticular screw placement. They were then provided reading on C1-C2 transarticular screw placement. Residents were then divided into a "self-directed learning" group and a "mentored learning" group. All residents then performed the technique on models, with the "mentored" group receiving a lecture and coaching from the mentor. The models were analyzed for technique errors and the previous test was administered again as a posttest. The test and screw placement were repeated 4 months later. Residents without mentoring had an average improvement of 4.5 points, those with mentoring had average improvement of 8.6 points (P=0.0068). The screw placement technique error rate for the nonmentored group (n=8) was 2.55, and for the mentored group (n=9) was 1.47 (P=0.004). Sixteen residents completed the delayed test, 7 from the nonmentored groups and 8 from the mentored group. Nine residents were able to repeat the screw placement technique 4 months after the initial test and screw placement, 3 nonentored, and 6 mentored. Although there were some trends toward the mentored group having better retention, neither knowledge nor skill was statistically different. This preliminary trial seems to indicate that residents provided a lecture and guided technical instruction will obtain knowledge and perform procedures better than those that do not. Conclusions based upon Post Graduate year, motivation, and interest in spine surgery could

Testing of irradiated and annealed 15H2MFA materials

International Nuclear Information System (INIS)

Gillemot, F.; Uri, G.

1994-01-01

A set of surveillance samples made from 15H2MFA material has been studied in the laboratory of AEKI. Miniature notched tensile specimens were cut from some remnants of irradiated and broke surveillance charpy remnants. The Absorbed Specific Fracture Energy (ASFE) was measured on the specimens. A cutting machine and testing technique were elaborated for the measurements. The second part of the Charpy remnants was annealed at 460 deg. C and 490 deg. C for 6-8 hours. The specimens were tested similarity and the results were compared. (author). 5 refs, 9 figs

Complex test of the C-PORCA 5.0 using HELIOS calculations

International Nuclear Information System (INIS)

Pos, I.; Nemes, I.; Patai-Szabo, S.

2001-01-01

Testing of C-PORCA 5.0 model using HELIOS calculation was performed. The basis of tests was a 30-degree core sector of WWER-440 containing differently burned fuel assemblies. Both with HELIOS and C-PORCA code one assembly burnup was calculated in infinite lattice assumption. Then differently burned fuel moved to a 30-degree core sector. Finally a 30-degree core was calculated and the HELIOS and C-PORCA results were compared. The comparison used in a validation procedure of C-PORCA model during introduction of higher enriched fuel to Paks units (Authors)

Theoretical studies on the electronic and optoelectronic properties of [A.2AP(w)/A*.2AP(WC)/C.2AP(w)/C*.2AP(WC)/C.A(w)/C*.A(WC)]-Au8 mismatch nucleobase complexes

Science.gov (United States)

Srivastava, Ruby

2018-01-01

The electronic and optoelectronic properties of [A.2AP(w)/A*.2AP(WC)/C.2AP(w)/C*.2AP(WC)/C.A(w)/ C*.A(WC)]-Au8 metal-mismatch nucleobase complexes are investigated by means of density functional theory and time-dependent methods. We selected these mispairs as 2-aminopurine (2AP) produces incorporation errors when binding with cytosine (C) into the wobble (w) C.2AP(w) mispair, and is tautomerised into Watson-Crick (WC)-like base mispair C*.2AP(WC) and less effectively produces A.2AP(w)/A*.2AP(WC) mispairs. The vertical ionisation potential, vertical electron affinity, hardness and electrophilicity index of these complexes have also been discussed. The modifications of energy levels and charge density distributions of the frontier orbitals are also analysed. The absorption spectra of these complexes lie in the visible region, which suggests their application in fluorescent-bio imaging. The mechanism of cooperativity effect is studied by molecular orbital potential (MEP), atoms-in-molecules (AIM) and natural bond orbital analyses. Most metalated pairs have smaller HOMO-LUMO band gaps than the isolated mismatch nucleobases which suggest interesting consequences for electron transfer through DNA duplexes.

C2 Agility

DEFF Research Database (Denmark)

Mitchell, Dr. William; Alberts, David S.; Bernier, Francois

of improving C2 Agility with empirical evidence obtained from a set of retrospective case studies and simulation-based experiments. Further, it identified next steps toward practical implementation in NATO operations and priorities for increasing the rigor and practicality of methods for measuring...... and improving C2 Agility. The 21st century military mission space is large and complex, characterized by extreme uncertainty, and exposed to increased public and media scrutiny. In addition to the high intensity combat operations traditionally associated with the military, potential missions include a wide...

Direct measurements of rate constants for the reactions of CH3 radicals with C2H6, C2H4, and C2H2 at high temperatures.

Science.gov (United States)

Peukert, S L; Labbe, N J; Sivaramakrishnan, R; Michael, J V

2013-10-10

The shock tube technique has been used to study the reactions CH3 + C2H6 → C2H4 + CH4 + H (1), CH3 + C2H4 → Products + H (2), and CH3 + C2H2 → Products + H (3). Biacetyl, (CH3CO)2, was used as a clean high temperature thermal source for CH3-radicals for all the three reactions studied in this work. For reaction 1, the experiments span a T-range of 1153 K ≤ T ≤ 1297 K, at P ~ 0.4 bar. The experiments on reaction 2 cover a T-range of 1176 K ≤ T ≤ 1366 K, at P ~ 1.0 bar, and those on reaction 3 a T-range of 1127 K ≤ T ≤ 1346 K, at P ~ 1.0 bar. Reflected shock tube experiments performed on reactions 1-3, monitored the formation of H-atoms with H-atom Atomic Resonance Absorption Spectrometric (ARAS). Fits to the H-atom temporal profiles using an assembled kinetics model were used to make determinations for k1, k2, and k3. In the case of C2H6, the measurements of [H]-atoms were used to derive direct high-temperature rate constants, k1, that can be represented by the Arrhenius equation k1(T) = 5.41 × 10(-12) exp(-6043 K/T) cm(3) molecules(-1) s(-1) (1153 K ≤ T ≤ 1297 K) for the only bimolecular process that occurs, H-atom abstraction. TST calculations based on ab initio properties calculated at the CCSD(T)/CBS//M06-2X/cc-pVTZ level of theory show excellent agreement, within ±20%, of the measured rate constants. For the reaction of CH3 with C2H4, the present rate constant results, k2', refer to the sum of rate constants, k(2b) + k(2c), from two competing processes, addition-elimination, and the direct abstraction CH3 + C2H4 → C3H6 + H (2b) and CH3 + C2H4 → C2H2 + H + CH4 (2c). Experimental rate constants for k2' can be represented by the Arrhenius equation k2'(T) = 2.18 × 10(-10) exp(-11830 K/T) cm(3) molecules(-1) s(-1) (1176 K ≤ T ≤ 1366 K). The present results are in excellent agreement with recent theoretical predictions. The present study provides the only direct measurement for the high-temperature rate constants for these channels

CO2 enrichment inhibits shoot nitrate assimilation in C3 but not C4 plants and slows growth under nitrate in C3 plants.

Science.gov (United States)

Bloom, Arnold J; Asensio, Jose Salvador Rubaio; Randall, Lesley; Rachmilevitch, Shimon; Cousins, Asaph B; Carlisle, Eli A

2012-02-01

The CO2 concentration in Earth's atmosphere may double during this century. Plant responses to such an increase depend strongly on their nitrogen status, but the reasons have been uncertain. Here, we assessed shoot nitrate assimilation into amino acids via the shift in shoot CO2 and O2 fluxes when plants received nitrate instead of ammonium as a nitrogen source (deltaAQ). Shoot nitrate assimilation became negligible with increasing CO2 in a taxonomically diverse group of eight C3 plant species, was relatively insensitive to CO2 in three C4 species, and showed an intermediate sensitivity in two C3-C4 intermediate species. We then examined the influence of CO2 level and ammonium vs. nitrate nutrition on growth, assessed in terms of changes in fresh mass, of several C3 species and a Crassulacean acid metabolism (CAM) species. Elevated CO2 (720 micromol CO2/mol of all gases present) stimulated growth or had no effect in the five C3 species tested when they received ammonium as a nitrogen source but inhibited growth or had no effect if they received nitrate. Under nitrate, two C3 species grew faster at sub-ambient (approximately 310 micromol/mol) than elevated CO2. A CAM species grew faster at ambient than elevated or sub-ambient CO2 under either ammonium or nitrate nutrition. This study establishes that CO2 enrichment inhibits shoot nitrate assimilation in a wide variety of C3 plants and that this phenomenon can have a profound effect on their growth. This indicates that shoot nitrate assimilation provides an important contribution to the nitrate assimilation of an entire C3 plant. Thus, rising CO2 and its effects on shoot nitrate assimilation may influence the distribution of C3 plant species.

Isolation and characterization of canine parvovirus type 2c (CPV-2c from symptomatic puppies

Directory of Open Access Journals (Sweden)

R Puentes

2012-09-01

Full Text Available Canine parvovirus type 2 (CPV-2 is a leading cause of diarrhea in puppies in several parts of the world. In this study CPV-2 was detected and recovered from puppies showing clinical disease from Montevideo, Uruguay. Samples were processed and used to infect CRFK and MDCK cells in order to isolate the virus. Out of twelve, two samples were positive for CPV-2. A genomic region of 583 bp was amplified and the molecular characterization was performed by sequencing, phylogenetic analysis and Restriction Fragment Length Polymorphism (RFLP. Two isolated viruses (UY1 and UY2 were CPV-2c-like viruses. The comparison between the cytophatic effect (CPE of CPV-2 (vaccinal virus and CPV-2c (isolated virus on primary canine cells cultures and on CRFK line cells, demonstrated that CPV-2c is less citopathogenic in CRFK than in primary cultures. Our study represents the first report on isolation and characterization of canine parvovirus type 2c (CPV-2c in cell cultures from South American dogs.

GluN2C/GluN2D subunit-selective NMDA receptor potentiator CIQ reverses MK-801-induced impairment in prepulse inhibition and working memory in Y-maze test in mice

Science.gov (United States)

Suryavanshi, P S; Ugale, R R; Yilmazer-Hanke, D; Stairs, D J; Dravid, S M

2014-01-01

Background and Purpose Despite ample evidence supporting the N-methyl-d-aspartate receptor (NMDAR) hypofunction hypothesis of schizophrenia, progress in the development of effective therapeutics based on this hypothesis has been limited. Facilitation of NMDA receptor function by co-agonists (d-serine or glycine) only partially alleviates the symptoms in schizophrenia; other means to facilitate NMDA receptors are required. NMDA receptor sub-types differ in their subunit composition, with varied GluN2 subunits (GluN2A-GluN2D) imparting different physiological, biochemical and pharmacological properties. CIQ is a positive allosteric modulator that is selective for GluN2C/GluN2D-containing NMDA receptors (Mullasseril et al.). Experimental Approach The effect of systemic administration of CIQ was tested on impairment in prepulse inhibition (PPI), hyperlocomotion and stereotypy induced by i.p. administration of MK-801 and methamphetamine. The effect of CIQ was also tested on MK-801-induced impairment in working memory in Y-maze spontaneous alternation test. Key Results We found that systemic administration of CIQ (20 mg·kg−1, i.p.) in mice reversed MK-801 (0.15 mg·kg−1, i.p.)-induced, but not methamphetamine (3 mg·kg−1, i.p.)-induced, deficit in PPI. MK-801 increased the startle amplitude to pulse alone, which was not reversed by CIQ. In contrast, methamphetamine reduced the startle amplitude to pulse alone, which was reversed by CIQ. CIQ also partially attenuated MK-801- and methamphetamine-induced hyperlocomotion and stereotyped behaviours. Additionally, CIQ reversed the MK-801-induced working memory deficit in spontaneous alternation in a Y-maze. Conclusion and Implications Together, these results suggest that facilitation of GluN2C/GluN2D-containing receptors may serve as an important therapeutic strategy for treating positive and cognitive symptoms in schizophrenia. PMID:24236947

Quantitative assessment of the BETHSY 6.9c test simulation

International Nuclear Information System (INIS)

Hrvatin, S.; Prosek, A.

2000-01-01

In the field of nuclear engineering, complex thermal-hydraulic computer codes are used to simulate and predict various transients in nuclear power plants. These computer codes are validated for overall system simulation by using experimental results, obtained on the integral test facilities. A post-test calculation of BETHSY 6.9c test with the RELAP5/MOD3.2 computer code has been performed in order to improve the input model in the future. The qualitative comparison of the results showed that most of the relevant parameters are predicted reasonably well. The quantitative assessment of the results was performed using the so-called Fast Fourier Transform Based Methodology. The FFTBM delineates and quantifies differences between calculated and experimental parameters in the frequency domain. The analysis showed that the the code calculations yield acceptable results. However, the primary pressure acceptability criterion is not fulfilled. This indicates that primary pressure calculation at low pressures is less accurate than at typical transient conditions. In general, it can be concluded that the RELAP5/MOD3.2 computer code can be used to analyze midloop operation at low power and pressure conditions. (author)

Cold spray deposition of Ti{sub 2}AlC coatings for improved nuclear fuel cladding

Energy Technology Data Exchange (ETDEWEB)

Maier, Benjamin R. [University of Wisconsin, Madison, WI (United States); Garcia-Diaz, Brenda L. [Savannah River National Laboratory, Aiken, SC (United States); Hauch, Benjamin [University of Wisconsin, Madison, WI (United States); Olson, Luke C.; Sindelar, Robert L. [Savannah River National Laboratory, Aiken, SC (United States); Sridharan, Kumar, E-mail: kumar@engr.wisc.edu [University of Wisconsin, Madison, WI (United States)

2015-11-15

Coatings of Ti{sub 2}AlC MAX phase compound have been successfully deposited on Zircaloy-4 (Zry-4) test flats, with the goal of enhancing the accident tolerance of LWR fuel cladding. Low temperature powder spray process, also known as cold spray, has been used to deposit coatings ∼90 μm in thickness using powder particles of <20 μm. X-ray diffraction analysis showed the phase-content of the deposited coatings to be identical to the powders indicating that no phase transformation or oxidation had occurred during the coating deposition process. The coating exhibited a high hardness of about 800 H{sub K} and pin-on-disk wear tests using abrasive ruby ball counter-surface showed the wear resistance of the coating to be significantly superior to the Zry-4 substrate. Scratch tests revealed the coatings to be well-adhered to the Zry-4 substrate. Such mechanical integrity is required for claddings from the standpoint of fretting wear resistance and resisting wear handling and insertion. Air oxidation tests at 700 °C and simulated LOCA tests at 1005 °C in steam environment showed the coatings to be significantly more oxidation resistant compared to Zry-4 suggesting that such coatings can potentially provide accident tolerance to nuclear fuel cladding. - Highlights: • Deposited Ti{sub 2}AlC coatings on Zircaloy-4 substrates with a low pressure powder spray process, also known as cold spray. • Coatings have high hardness and wear resistance for both damage resistance during rod insertion and fretting wear resistance. • The oxidation resistance of Ti{sub 2}AlC coated Zircaloy-4 at 700 °C and 1005 °C was significantly superior to uncoated Zircaloy. • Cold spray of Ti{sub 2}AlC demonstrates considerable promise as a near-term solution for accident tolerant Zr-alloy fuel claddings.

Application of C/C composites to the combustion chamber of rocket engines. Part 1: Heating tests of C/C composites with high temperature combustion gases

Science.gov (United States)

Tadano, Makoto; Sato, Masahiro; Kuroda, Yukio; Kusaka, Kazuo; Ueda, Shuichi; Suemitsu, Takeshi; Hasegawa, Satoshi; Kude, Yukinori

1995-04-01

Carbon fiber reinforced carbon composite (C/C composite) has various superior properties, such as high specific strength, specific modulus, and fracture strength at high temperatures of more than 1800 K. Therefore, C/C composite is expected to be useful for many structural applications, such as combustion chambers of rocket engines and nose-cones of space-planes, but C/C composite lacks oxidation resistivity in high temperature environments. To meet the lifespan requirement for thermal barrier coatings, a ceramic coating has been employed in the hot-gas side wall. However, the main drawback to the use of C/C composite is the tendency for delamination to occur between the coating layer on the hot-gas side and the base materials on the cooling side during repeated thermal heating loads. To improve the thermal properties of the thermal barrier coating, five different types of 30-mm diameter C/C composite specimens constructed with functionally gradient materials (FGM's) and a modified matrix coating layer were fabricated. In this test, these specimens were exposed to the combustion gases of the rocket engine using nitrogen tetroxide (NTO) / monomethyl hydrazine (MMH) to evaluate the properties of thermal and erosive resistance on the thermal barrier coating after the heating test. It was observed that modified matrix and coating with FGM's are effective in improving the thermal properties of C/C composite.

Effect of Mo2C content on the properties of TiC/TiB2 base cermets

International Nuclear Information System (INIS)

Takagi, Ken-ichi; Osada, Ken; Koike, Wataru; Fujima, Takuya

2009-01-01

The effects of Mo 2 C content on the microstructure and mechanical properties of TiC/TiB 2 base cermets were studied using the model cermets with the compositions of TiC/TiB 2 -(11-17)Mo 2 C-24Ni (mass%). TiC and TiB 2 ratio is set to molar ratio of 59:41 that is near quasi-eutectic composition. As a result, both transverse rupture strength and hardness of the cermets showed maxima for the cermet containing 13% Mo 2 C. The cermet achieved remarkable microstructural refinement and still maintained characteristic core-rim structure of the TiC base cermets. TiC/TiB 2 cermets, in addition to TiCN base cermets, are a good alternative material to cemented carbides.

Observation of χc 2→η'η' and χc 0 ,2→η η'

Science.gov (United States)

Ablikim, M.; Achasov, M. N.; Ahmed, S.; Albrecht, M.; Amoroso, A.; An, F. F.; An, Q.; Bai, J. Z.; Bai, Y.; Bakina, O.; Baldini Ferroli, R.; Ban, Y.; Bennett, D. W.; Bennett, J. V.; Berger, N.; Bertani, M.; Bettoni, D.; Bian, J. M.; Bianchi, F.; Boger, E.; Boyko, I.; Briere, R. A.; Cai, H.; Cai, X.; Cakir, O.; Calcaterra, A.; Cao, G. F.; Cetin, S. A.; Chai, J.; Chang, J. F.; Chelkov, G.; Chen, G.; Chen, H. S.; Chen, J. C.; Chen, M. L.; Chen, S. J.; Chen, X. R.; Chen, Y. B.; Chu, X. K.; Cibinetto, G.; Dai, H. L.; Dai, J. P.; Dbeyssi, A.; Dedovich, D.; Deng, Z. Y.; Denig, A.; Denysenko, I.; Destefanis, M.; de Mori, F.; Ding, Y.; Dong, C.; Dong, J.; Dong, L. Y.; Dong, M. Y.; Dorjkhaidav, O.; Dou, Z. L.; Du, S. X.; Duan, P. F.; Fang, J.; Fang, S. S.; Fang, X.; Fang, Y.; Farinelli, R.; Fava, L.; Fegan, S.; Feldbauer, F.; Felici, G.; Feng, C. Q.; Fioravanti, E.; Fritsch, M.; Fu, C. D.; Gao, Q.; Gao, X. L.; Gao, Y.; Gao, Y. G.; Gao, Z.; Garzia, I.; Goetzen, K.; Gong, L.; Gong, W. X.; Gradl, W.; Greco, M.; Gu, M. H.; Gu, S.; Gu, Y. T.; Guo, A. Q.; Guo, L. B.; Guo, R. P.; Guo, Y. P.; Haddadi, Z.; Han, S.; Hao, X. Q.; Harris, F. A.; He, K. L.; He, X. Q.; Heinsius, F. H.; Held, T.; Heng, Y. K.; Holtmann, T.; Hou, Z. L.; Hu, C.; Hu, H. M.; Hu, T.; Hu, Y.; Huang, G. S.; Huang, J. S.; Huang, X. T.; Huang, X. Z.; Huang, Z. L.; Hussain, T.; Ikegami Andersson, W.; Ji, Q.; Ji, Q. P.; Ji, X. B.; Ji, X. L.; Jiang, X. S.; Jiang, X. Y.; Jiao, J. B.; Jiao, Z.; Jin, D. P.; Jin, S.; Jin, Y.; Johansson, T.; Julin, A.; Kalantar-Nayestanaki, N.; Kang, X. L.; Kang, X. S.; Kavatsyuk, M.; Ke, B. C.; Khan, T.; Khoukaz, A.; Kiese, P.; Kliemt, R.; Koch, L.; Kolcu, O. B.; Kopf, B.; Kornicer, M.; Kuemmel, M.; Kuhlmann, M.; Kupsc, A.; Kühn, W.; Lange, J. S.; Lara, M.; Larin, P.; Lavezzi, L.; Leithoff, H.; Leng, C.; Li, C.; Li, Cheng; Li, D. M.; Li, F.; Li, F. Y.; Li, G.; Li, H. B.; Li, H. J.; Li, J. C.; Li, Jin; Li, K. J.; Li, Kang; Li, Ke; Li, Lei; Li, P. L.; Li, P. R.; Li, Q. Y.; Li, T.; Li, W. D.; Li, W. G.; Li, X. L.; Li, X. N.; Li, X. Q.; Li, Z. B.; Liang, H.; Liang, Y. F.; Liang, Y. T.; Liao, G. R.; Lin, D. X.; Liu, B.; Liu, B. J.; Liu, C. X.; Liu, D.; Liu, F. H.; Liu, Fang; Liu, Feng; Liu, H. B.; Liu, H. M.; Liu, Huanhuan; Liu, Huihui; Liu, J. B.; Liu, J. P.; Liu, J. Y.; Liu, K.; Liu, K. Y.; Liu, Ke; Liu, L. D.; Liu, P. L.; Liu, Q.; Liu, S. B.; Liu, X.; Liu, Y. B.; Liu, Z. A.; Liu, Zhiqing; Long, Y. F.; Lou, X. C.; Lu, H. J.; Lu, J. G.; Lu, Y.; Lu, Y. P.; Luo, C. L.; Luo, M. X.; Luo, X. L.; Lyu, X. R.; Ma, F. C.; Ma, H. L.; Ma, L. L.; Ma, M. M.; Ma, Q. M.; Ma, T.; Ma, X. N.; Ma, X. Y.; Ma, Y. M.; Maas, F. E.; Maggiora, M.; Malik, Q. A.; Mao, Y. J.; Mao, Z. P.; Marcello, S.; Meng, Z. X.; Messchendorp, J. G.; Mezzadri, G.; Min, J.; Min, T. J.; Mitchell, R. E.; Mo, X. H.; Mo, Y. J.; Morales Morales, C.; Morello, G.; Muchnoi, N. Yu.; Muramatsu, H.; Musiol, P.; Mustafa, A.; Nefedov, Y.; Nerling, F.; Nikolaev, I. B.; Ning, Z.; Nisar, S.; Niu, S. L.; Niu, X. Y.; Olsen, S. L.; Ouyang, Q.; Pacetti, S.; Pan, Y.; Papenbrock, M.; Patteri, P.; Pelizaeus, M.; Pellegrino, J.; Peng, H. P.; Peters, K.; Pettersson, J.; Ping, J. L.; Ping, R. G.; Pitka, A.; Poling, R.; Prasad, V.; Qi, H. R.; Qi, M.; Qian, S.; Qiao, C. F.; Qin, J. J.; Qin, N.; Qin, X. S.; Qin, Z. H.; Qiu, J. F.; Rashid, K. H.; Redmer, C. F.; Richter, M.; Ripka, M.; Rolo, M.; Rong, G.; Rosner, Ch.; Ruan, X. D.; Sarantsev, A.; Savrié, M.; Schnier, C.; Schoenning, K.; Shan, W.; Shao, M.; Shen, C. P.; Shen, P. X.; Shen, X. Y.; Sheng, H. Y.; Song, J. J.; Song, W. M.; Song, X. Y.; Sosio, S.; Sowa, C.; Spataro, S.; Sun, G. X.; Sun, J. F.; Sun, L.; Sun, S. S.; Sun, X. H.; Sun, Y. J.; Sun, Y. K.; Sun, Y. Z.; Sun, Z. J.; Sun, Z. T.; Tang, C. J.; Tang, G. Y.; Tang, X.; Tapan, I.; Tiemens, M.; Tsednee, B. T.; Uman, I.; Varner, G. S.; Wang, B.; Wang, B. L.; Wang, D.; Wang, D. Y.; Wang, Dan; Wang, K.; Wang, L. L.; Wang, L. S.; Wang, M.; Wang, P.; Wang, P. L.; Wang, W. P.; Wang, X. F.; Wang, Y.; Wang, Y. D.; Wang, Y. F.; Wang, Y. Q.; Wang, Z.; Wang, Z. G.; Wang, Z. H.; Wang, Z. Y.; Wang, Zongyuan; Weber, T.; Wei, D. H.; Wei, J. H.; Weidenkaff, P.; Wen, S. P.; Wiedner, U.; Wolke, M.; Wu, L. H.; Wu, L. J.; Wu, Z.; Xia, L.; Xia, Y.; Xiao, D.; Xiao, H.; Xiao, Y. J.; Xiao, Z. J.; Xie, Y. G.; Xie, Y. H.; Xiong, X. A.; Xiu, Q. L.; Xu, G. F.; Xu, J. J.; Xu, L.; Xu, Q. J.; Xu, Q. N.; Xu, X. P.; Yan, L.; Yan, W. B.; Yan, W. C.; Yan, Y. H.; Yang, H. J.; Yang, H. X.; Yang, L.; Yang, Y. H.; Yang, Y. X.; Ye, M.; Ye, M. H.; Yin, J. H.; You, Z. Y.; Yu, B. X.; Yu, C. X.; Yu, J. S.; Yuan, C. Z.; Yuan, Y.; Yuncu, A.; Zafar, A. A.; Zeng, Y.; Zeng, Z.; Zhang, B. X.; Zhang, B. Y.; Zhang, C. C.; Zhang, D. H.; Zhang, H. H.; Zhang, H. Y.; Zhang, J.; Zhang, J. L.; Zhang, J. Q.; Zhang, J. W.; Zhang, J. Y.; Zhang, J. Z.; Zhang, K.; Zhang, L.; Zhang, S. Q.; Zhang, X. Y.; Zhang, Y. H.; Zhang, Y. T.; Zhang, Yang; Zhang, Yao; Zhang, Yu; Zhang, Z. H.; Zhang, Z. P.; Zhang, Z. Y.; Zhao, G.; Zhao, J. W.; Zhao, J. Y.; Zhao, J. Z.; Zhao, Lei; Zhao, Ling; Zhao, M. G.; Zhao, Q.; Zhao, S. J.; Zhao, T. C.; Zhao, Y. B.; Zhao, Z. G.; Zhemchugov, A.; Zheng, B.; Zheng, J. P.; Zheng, W. J.; Zheng, Y. H.; Zhong, B.; Zhou, L.; Zhou, X.; Zhou, X. K.; Zhou, X. R.; Zhou, X. Y.; Zhou, Y. X.; Zhu, J.; Zhu, K.; Zhu, K. J.; Zhu, S.; Zhu, S. H.; Zhu, X. L.; Zhu, Y. C.; Zhu, Y. S.; Zhu, Z. A.; Zhuang, J.; Zotti, L.; Zou, B. S.; Zou, J. H.; Besiii Collaboration

2017-12-01

Using a sample of 448.1 ×106 ψ (3686 ) events collected with the BESIII detector in 2009 and 2012, we study the decays χc 0 ,2→η'η' and η η' . The decays χc 2→η'η' , χc 0→η η' and χc 2→η η' are observed for the first time with statistical significances of 9.6 σ , 13.4 σ and 7.5 σ , respectively. The branching fractions are determined to be B (χc 0→η'η')=(2.19 ±0.03 ±0.14 )×10-3 , B (χc 2→η'η')=(4.76 ±0.56 ±0.38 )×10-5 , B (χc 0→η η')=(8.92 ±0.84 ±0.65 )×10-5 and B (χc 2→η η')=(2.27 ±0.43 ±0.25 )×10-5 , where the first uncertainties are statistical and the second are systematic. The precision for the measurement of B (χc 0→η'η') is significantly improved compared to previous measurements. Based on the measured branching fractions, the role played by the doubly and singly Okubo-Zweig-Iizuka disconnected transition amplitudes for χc 0 ,2 decays into pseudoscalar meson pairs can be clarified.

Micro-nanocomposites Al2O3/ NbC/ WC and Al2O3/ NbC/ TaC

International Nuclear Information System (INIS)

Santos, Thais da Silva

2014-01-01

Alumina based ceramics belong to a class of materials designated as structural, which are widely used in cutting tools. Although alumina has good properties for application as a structural ceramics, composites with different additives have been produced with the aim of improving its fracture toughness and mechanical strength. New studies point out micro-nanocomposites, wherein the addition of micrometric particles should enhance mechanical strength, and nano-sized particles enhance fracture toughness. In this work, alumina based micro nanocomposites were obtained by including nano-sized NbC and micrometer WC particles at 2:1, 6:4, 10:5 and 15:10 vol% proportions, and also with the inclusion of nano-sized NbC and micrometer TaC particles at 2:1 vol% proportion. For the study of densification, micro-nanocomposites were sintered in a dilatometer with a heating rate of 20°C/min until a temperature of 1800°C in argon atmosphere. Based on the dilatometry results, specimens were sintered in a resistive graphite furnace under argon atmosphere between 1500°C and 1700°C by holding the sintering temperature for 30 minutes. Densities, crystalline phases, hardness and tenacity were determined, and micro-nanocomposites microstructures were analyzed. The samples Al 2 O 3 : NbC: TaC sintered at 1700 ° C achieved the greater apparent density (~ 95% TD) and the sample sintered at 1600 ° C showed homogeneous microstructure and increased hardness value (15.8 GPa) compared to the pure alumina . The compositions with 3% inclusions are the most promising for future applications. (author)

Results from Cycles 1 and 2 of NNWSI Series 2 spent fuel dissolution tests

International Nuclear Information System (INIS)

Wilson, C.N.

1987-05-01

PWR spent fuel rod segments from the H.B. Robinson Unit 2 and Turkey Point Unit 3 reactors were leach tested in Nevada Nuclear Waste Storage Investigations (NNWSI) reference J-13 water under ambient hot cell conditions. The test matrix included bare fuel plus the cladding, rod segments with artificially induced cladding defects, and undefected rod segments. Radionuclide release results are presented and discussed. The actinides Pu, Am, Cm and Np appear to have been released congruently as the UO 2 oxide fuel matrix dissolved. Preferential U release measured in certain tests may be related to dissolution of oxidized UO/sub 2+x/ from the fuel surface, and/or greater solubility (and mobility) of U relative to the other actinides within defected cladding specimens. Uranium solubility measured in the J-13 water was much greater then that measured in deionized water in previous tests. All of the principal fission products analyzed ( 137 Cs, 129 I, 99 Tc and 90 Sr) were released preferentially relative to the actinides. Preferential release of activation product 14 C was also measured, with a portion of the 14 C release appearing to originate from the cladding exterior surface. Much greater fractional fuel dissolution appeared to have occurred with bare fuel particles than from fuel contained in defected cladding. Actinide release from test specimens containing small (∼200 μm) laser-drilled holes through the cladding was not significantly greater than from undefected specimens