WorldWideScience

Sample records for hydrocarbon maturity range

  1. Extraction of hydrocarbons from high-maturity Marcellus Shale using supercritical carbon dioxide

    Science.gov (United States)

    Jarboe, Palma B.; Philip A. Candela,; Wenlu Zhu,; Alan J. Kaufman,

    2015-01-01

    Shale is now commonly exploited as a hydrocarbon resource. Due to the high degree of geochemical and petrophysical heterogeneity both between shale reservoirs and within a single reservoir, there is a growing need to find more efficient methods of extracting petroleum compounds (crude oil, natural gas, bitumen) from potential source rocks. In this study, supercritical carbon dioxide (CO2) was used to extract n-aliphatic hydrocarbons from ground samples of Marcellus shale. Samples were collected from vertically drilled wells in central and western Pennsylvania, USA, with total organic carbon (TOC) content ranging from 1.5 to 6.2 wt %. Extraction temperature and pressure conditions (80 °C and 21.7 MPa, respectively) were chosen to represent approximate in situ reservoir conditions at sample depth (1920−2280 m). Hydrocarbon yield was evaluated as a function of sample matrix particle size (sieve size) over the following size ranges: 1000−500 μm, 250−125 μm, and 63−25 μm. Several methods of shale characterization including Rock-Eval II pyrolysis, organic petrography, Brunauer−Emmett−Teller surface area, and X-ray diffraction analyses were also performed to better understand potential controls on extraction yields. Despite high sample thermal maturity, results show that supercritical CO2 can liberate diesel-range (n-C11 through n-C21) n-aliphatic hydrocarbons. The total quantity of extracted, resolvable n-aliphatic hydrocarbons ranges from approximately 0.3 to 12 mg of hydrocarbon per gram of TOC. Sieve size does have an effect on extraction yield, with highest recovery from the 250−125 μm size fraction. However, the significance of this effect is limited, likely due to the low size ranges of the extracted shale particles. Additional trends in hydrocarbon yield are observed among all samples, regardless of sieve size: 1) yield increases as a function of specific surface area (r2 = 0.78); and 2) both yield and surface area increase with increasing

  2. Reconstruction of burial history, temperature, source rock maturity and hydrocarbon generation in the northwestern Dutch offshore

    NARCIS (Netherlands)

    Abdul Fattah, R.; Verweij, J.M.; Witmans, N.; Veen, J.H. ten

    2012-01-01

    3D basin modelling is used to investigate the history of maturation and hydrocarbon generation on the main platforms in the northwestern part of the offshore area of the Netherlands. The study area covers the Cleaverbank and Elbow Spit Platforms. Recently compiled maps and data are used to build the

  3. Thermal maturity history and implications for hydrocarbon exploration in the Catatumbo basin, Colombia

    International Nuclear Information System (INIS)

    Rangel, Antonio; Hernandez, Roberto

    2007-01-01

    A thermal model integrated with oil and gas geochemical study has been constructed for the Catatumbo basin, Colombia for provides petroleum system data for hydrocarbon exploration. The calibration of the thermal model with maturity data took into account a changing heat flow scheme which included a thermal increase towards the end of the Jurassic and another one in the early Eocene, associated with rifting events. Locally, active/generating source rocks are within the synclines axes. The hydrocarbon expulsion time for Cretaceous source rocks (Capacho and La Luna formations) started in the upper Paleocene-Eocene, while for the los Cuervos Formation the generation and expulsion started of 1 0 my. The petroleum expelled during the Paleocene-Miocene, were likely accumulated in structures formed since the end of the cretaceous, while the younger structures that resulted from the Andean orogen were charged by remigration from the older structures and additionally with the youngest lately generated hydrocarbons. The accumulations of hydrocarbons are mainly the result of generation and migration locally within the basin. The Catatumbo Basin contains thermogenic wet gases with different degrees of thermal maturity which varies from around 1,0 for 2,5 equivalent Ro. The highest degree of thermal evolution according to maturity indicators and thermal modeling is in the southern area, which is prospective for wet gas. The central and northern area appears more prospective for oil with minor amounts of gas

  4. Long range transport of hydrocarbons in the Southern Ocean

    International Nuclear Information System (INIS)

    Pinturier, L.; Leureillard, J.; Arnold, M.; Tisnerat, N.; Pichon, J.J.; Gireaudau, J.

    1999-01-01

    We report here the first results for hydrocarbon analyses of deep surface sediments collected in the Indian sector of the Southern Ocean. The samples were taken along a north-south transect ranging from 43 deg. S to 55 deg. S in the southwestern Crozet Basin. In order to identify these compounds and elucidate their origins, various techniques were used: gas chromatography and gas chromatography coupled with mass spectrometry; Accelerator Mass Spectrometry (Tandetron: mass spectrometer coupled with a Tandem accelerator allowing the measure of 14 C/ 12 C ratio)

  5. Process for paraffin isomerization of a distillate range hydrocarbon feedstock

    Energy Technology Data Exchange (ETDEWEB)

    Chen, N.Y.; Garwood, W.E.; McCullen, S.B.

    1993-01-19

    Various catalytic processes have been proposed to isomerize n-paraffins so as to lower the pour point of distillate range hydrocarbon feedstocks. However, many available feedstocks contain nitrogen impurities which tend to poison conventional paraffin isomerization catalysts. A process has been developed to obviate or alleviate this problem. According to the invention, the paraffin-containing feedstock is contacted with a crystalline aluminosilicate zeolite catalyst having pore openings defined by a ratio of sorption of n-hexane to o-xylene of over 3 vol % and the ability to crack 3-methylpentane in preference to 2,3 dimethylbutane under defined conditions. The zeolite catalyst includes a Group VIII metal and has a zeolite SiO[sub 2]/Al[sub 2]O[sub 3] ratio of at least 20:1. The contacting is carried out at 199-454 C and a pressure of 100-1,000 psig, preferably 250-600 psig. The group of medium pore zeolites which can be used in the process of the invention includes ZSM-22, ZSM-23, and ZSM-35. The Group VIII metals used in the catalyst are preferably selected from Pt, Pd, Ir, Os, Rh, and Ru and the metal is preferably incorporated into the zeolite by ion exchange up to a metal content of preferably 0.1-3 wt %. Experiments are described to illustrate the invention. 1 tab.

  6. Hydrocarbon Maturation and Os Mixing on Bolide Impact at the Frasnian-Famennian Boundary

    Science.gov (United States)

    Stein, H.; Zimmerman, A.; Yang, G.; Hannah, J.; Egenhoff, S.

    2009-04-01

    An intractable problem in the application of Re-Os geochemistry has been knowledge of the distribution of Re and Os between source rock and generated hydrocarbon. Solutions lie in combined experimental work with controlled and induced maturation, and field studies optimized by known source rock and time of hydrocarbon generation. The Siljan impact site with its variably tilted but largely intact Ordovician-Silurian sections provides an unsurpassed opportunity to examine the Re-Os systematics of source rock and generated crude oil, and the Re-Os imprint of the bolide. This three-component system contains (1) a time pin for maturation (377 ± 2 Ma; laser argon dating of impact melt, Reimold et al. 2005) arguably at the Frasnian-Famennian boundary, (2) known source rocks with kerogens still intact, and (3) crude oils generated on impact. Modeling takes into consideration the possibility of pre-impact maturation as well. At Siljan, numerous quarries expose the Upper Ordovician Boda and Kullsberg limestone mounds, and locally, the underlying and laterally equivalent Tretaspis (Fjäcka) shale. We obtained a sample of crude oil seeping from a drill hole in the quarry floor at Solberga. Preliminary Re-Os analyses on four aliquots of this oil form an excellent linear array in 187Re/188Os versus 187Os/188Os space. The associated age, however, is impossibly old (Neoproterozoic), and the initial 187Os/188Os unreasonably low (0.2). Rather, this linear array fits a mixing line between a meteoritic component and a hydrocarbon generated from the Tretaspis shale. We are presently performing further tests to isolate the two end-members. Filtering suggests that the extraterrestrial component consists of small physical particles which can be largely removed from the petroleum fraction. The extreme contrast in Re-Os composition between meteorite (known) and black shale (in progress) end-members maximizes the sensitivity of the isotopic study. Reimold, W.U., Kelley, S.P., Sherlock, S

  7. Organic maturation levels, thermal history and hydrocarbon source rock potential of the Namurian rocks of the Clare Basin, Ireland

    Energy Technology Data Exchange (ETDEWEB)

    Goodhue, Robbie; Clayton, Geoffrey [Trinity Coll., Dept. of Geology, Dublin (Ireland)

    1999-11-01

    Vitrinite reflectance data from two inland cored boreholes confirm high maturation levels throughout the onshore part of the Irish Clare Basin and suggest erosion of 2 to 4 km of late Carboniferous cover and elevated palaeogeothermal gradients in the Carboniferous section. The observed maturation gradients are fully consistent with the published hypothesis of a late Carboniferous/Permian 'superplume' beneath Pangaea but local vertical reversals in gradients also suggest a complex thermal regime probably involving advective heating. The uppermost Visean--lower Namurian Clare Shale is laterally extensive and up to 300 m thick. Although this unit is post-mature, TOC values of up to 15% suggest that it could have considerable hydrocarbon source rock potential in any less mature offshore parts of the basin. (Author)

  8. Frequency–amplitude range of hydrocarbon microtremors and a discussion on their source

    International Nuclear Information System (INIS)

    Gerivani, H; Hafezi Moghaddas, N; Ghafoori, M; Lashkaripour, G R; Haghshenas, E

    2012-01-01

    Recently, some studies have suggested using ambient noise as a tool for hydrocarbon reservoir investigation. This new passive seismic technique, named HyMas, is based on the positive energy anomaly in data spectra between 1 to 6 Hz for microtremor measurements over reservoirs, which are called hydrocarbon microtremors. Despite the acceptable results obtained by the HyMas technique, there are many unknowns, especially concerning the source and generation mechanism of hydrocarbon microtremors and the relations between reservoir characteristics and the attributes of hydrocarbon microtremors. In this study we tried to find the relations between reservoir characteristics, including fluid content and depth, for 12 sites around the world with hydrocarbon microtremor attributes, including peak amplitude and frequency. Based on the power spectral density curves of these 12 reservoirs, a frequency–amplitude range is also proposed as a criterion for separating hydrocarbon microtremors from local noise not related to reservoirs. Finally, the source of the hydrocarbon microtremors is discussed and tidal displacement is suggested as a probable agent for the generation of these anomalies. (paper)

  9. Pyrolysis of municipal plastic wastes for recovery of gasoline-range hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Demirbas, Ayhan [Department of Chemical Engineering, Selcuk University, Konya (Turkey)

    2004-08-01

    This paper describes non-catalytic pyrolysis of plastic waste materials. Three types of waste plastics were used in this study: polystyrene (PS), polyethylene (PE) and polypropylene (PP). Under pyrolysis conditions, plastic wastes can be decomposed into three fractions: gas, liquid and solid residue. The liquid products are usually composed of higher boiling point hydrocarbons. In order to obtain useful gasoline-range hydrocarbons from the pyrolytic oil, fractional distillation is preferred for product separation. More valuable chemical raw materials including benzene, toluene and other condensed aromatic hydrocarbons may be obtained by refining the pyrolytic oil. The results showed that waste PS yielded higher liquid, and waste PE and PP yielded higher gaseous products. The dominant pyrolytic liquid product of PS waste was styrene.

  10. Long-range correlations in rectal temperature fluctuations of healthy infants during maturation.

    Directory of Open Access Journals (Sweden)

    Georgette Stern

    Full Text Available BACKGROUND: Control of breathing, heart rate, and body temperature are interdependent in infants, where instabilities in thermoregulation can contribute to apneas or even life-threatening events. Identifying abnormalities in thermoregulation is particularly important in the first 6 months of life, where autonomic regulation undergoes critical development. Fluctuations in body temperature have been shown to be sensitive to maturational stage as well as system failure in critically ill patients. We thus aimed to investigate the existence of fractal-like long-range correlations, indicative of temperature control, in night time rectal temperature (T(rec patterns in maturing infants. METHODOLOGY/PRINCIPAL FINDINGS: We measured T(rec fluctuations in infants every 4 weeks from 4 to 20 weeks of age and before and after immunization. Long-range correlations in the temperature series were quantified by the correlation exponent, alpha using detrended fluctuation analysis. The effects of maturation, room temperature, and immunization on the strength of correlation were investigated. We found that T(rec fluctuations exhibit fractal long-range correlations with a mean (SD alpha of 1.51 (0.11, indicating that T(rec is regulated in a highly correlated and hence deterministic manner. A significant increase in alpha with age from 1.42 (0.07 at 4 weeks to 1.58 (0.04 at 20 weeks reflects a change in long-range correlation behavior with maturation towards a smoother and more deterministic temperature regulation, potentially due to the decrease in surface area to body weight ratio in the maturing infant. alpha was not associated with mean room temperature or influenced by immunization CONCLUSIONS: This study shows that the quantification of long-range correlations using alpha derived from detrended fluctuation analysis is an observer-independent tool which can distinguish developmental stages of night time T(rec pattern in young infants, reflective of maturation of

  11. Scents of adolescence: the maturation of the olfactory phenotype in a free-ranging mammal.

    Directory of Open Access Journals (Sweden)

    Barbara A Caspers

    Full Text Available Olfaction is an important sensory modality for mate recognition in many mammal species. Odorants provide information about the health status, genotype, dominance status and/or reproductive status. How and when odor profiles change during sexual maturation is, however often unclear, particularly in free-ranging mammals. Here, we investigated whether the wing sac odorant of male greater sac-winged bats (Saccopteryx bilineata, Emballonuridae differs between young and adults, and thus offers information about sexual maturity to potential mating partners. Using gas chromatography-mass spectrometry, we found differences in the odorants of young and adult males prior and during, but not after the mating period. The wing sac odorant of adult males consists of several substances, such as Pyrocoll, 2,6,10-trimethyl-3-oxo-6,10-dodecadienolide, and a so far unidentified substance; all being absent in the odor profiles of juveniles prior to the mating season. During the mating season, these substances are present in most of the juvenile odorants, but still at lower quantities compared to the wing sac odorants of adults. These results suggest that the wing sac odorant of males encodes information about age and/or sexual maturity. Although female S. bilineata start to reproduce at the age of half a year, most males of the same age postpone the sexual maturation of their olfactory phenotype until after the first mating season.

  12. Hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    1927-02-22

    Coal tar, mineral oils, bitumens, coal extraction products, hydrogenation products of coal, oil schists can be atomized and heated with steam to decompose pyrogenetically and form gases rich in olefins which may be heated with or without pressure and with or without catalysts to produce liquid hydrocarbons of low boiling point, some of which may be aromatic. The apparatus should be lined with copper, silica, or ferrosilicon to prevent contact of the bases with iron which causes deposition of soot. Catalysts used may be metal oxides, silica, graphite, active charcoal, mica, pumice, porcelain, barium carbonate, copper, silver, gold, chromium, boron, or their compounds. At temperatures from 300 to 400/sup 0/C, olefins are produced. At higher temperatures, naphthenes and benzene hydrocarbons are produced.

  13. Permian-Triassic maturation and multistage migration of hydrocarbons in the Assistência Formation (Irati Subgroup, Paraná Basin, Brazil: implications for the exploration model

    Directory of Open Access Journals (Sweden)

    António Mateus

    Full Text Available New lines of geological evidence strongly suggest that the main period of hydrocarbon maturation within Assistência Formation should be Permian-Triassic, stimulated by a high geothermal gradient that also sustained various manifestations of hydrothermal activity. Three main stages of fluid/hydrocarbon migration can also be inferred on the basis of multiscale observations: confined flow in late Permian to Triassic times, depending on the local build-up of fluid pressures; heterogeneous flow in Lower Cretaceous, triggered by a rejuvenated temperature gradient assisted by the early developed permeability conditions; and a late flow possibly driven by local pressure gradients, after complete cooling of dolerite dykes/sills. The early maturation and multistage migration of hydrocarbons have significant consequences in the design of exploration models to be applied in Paraná Basin.

  14. Impact of culture medium on maturation of bone marrow-derived murine dendritic cells via the aryl hydrocarbon receptor.

    Science.gov (United States)

    Ilchmann, Anne; Krause, Maren; Heilmann, Monika; Burgdorf, Sven; Vieths, Stefan; Toda, Masako

    2012-05-01

    The aryl hydrocarbon receptor (AhR) plays a role in modulating dendritic cell (DC) immunity. Iscove's modified Dulbecco's medium (IMDM) contains higher amounts of AhR ligands than RPMI1640 medium. Here, we examined the influence of AhR ligand-containing medium on the maturation and T-cell stimulatory capacity of bone marrow-derived murine dendritic cells (BMDCs). BMDCs generated in IMDM (BMDCs/IMDM) expressed higher levels of co-stimulatory and MHC class II molecules, and lower levels of pattern-recognition receptors, especially toll-like receptor (TLR) 2, TLR4, and scavenger receptor class A (SR-A), compared to BMDCs generated in RPMI1640 medium (BMDCs/RPMI). Cytokine responses against ligands of TLRs and antigen uptake mediated by SR-A were remarkably reduced in BMDCs/IMDM, whereas the T-cell stimulatory capacity of the cells was enhanced, compared to BMDCs/RPMI. The enhanced maturation of BMDCs/IMDM was attenuated in the presence of an AhR antagonist, indicating involvement of AhR in the maturation. Interestingly, BMDCs/IMDM induced Th2 and Th17 differentiation at low and high concentrations of antigen respectively, when co-cultured with CD4(+) T-cells from antigen-specific T-cell receptor transgenic mice. In contrast, BMDCs/RPMI induced Th1 differentiation predominantly in the co-culture. Taken together, optimal selection of medium seems necessary when studying BMDCs, depending on the target receptors on the cell surface of DCs and type of helper T-cells for the co-culture. Copyright © 2012 Elsevier Ltd. All rights reserved.

  15. Low-maturity Kulthieth Formation coal: A possible source of polycyclic aromatic hydrocarbons in benthic sediment of the northern Gulf of Alaska

    Science.gov (United States)

    Van Kooten, G. K.; Short, J.W.; Kolak, J.J.

    2002-01-01

    The successful application of forensic geology to contamination studies involving natural systems requires identification of appropriate endmembers and an understanding of the geologic setting and processes affecting the systems. Studies attempting to delineate the background, or natural, source for hydrocarbon contamination in Gulf of Alaska (GOA) benthic sediments have invoked a number of potential sources, including seep oils, source rocks, and coal. Oil seeps have subsequently been questioned as significant sources of hydrocarbons present in benthic sediments of the GOA in part because the pattern of relative polycyclic aromatic hydrocarbon (PAH) abundance characteristic of benthic GOA sediments is inconsistent with patterns typical of weathered seep oils. Likewise, native coal has been dismissed in part because ratios of labile hydrocarbons to total organic carbon (e.g. PAH:TOC) for Bering River coal field (BRCF) sources are too low - i.e. the coals are over mature - to be consistent with GOA sediments. We present evidence here that native coal may have been prematurely dismissed, because BRCF coals do not adequately represent the geochemical signatures of coals elsewhere in the Kulthieth Formation. Contrary to previous thought, Kulthieth Formation coals east of the BRCF have much higher PAH: TOC ratios, and the patterns of labile hydrocarbons in these low thermal maturity coals suggest a possible genetic relationship between Kulthieth Formation coals and nearby oil seeps on the Sullivan anticline. Analyses of low-maturity Kulthieth Formation coal indicate the low maturity coal is a significant source of PAH. Source apportionment models that neglect this source will underestimate the contribution of native coals to the regional background hydrocarbon signature. ?? Published by Elsevier Science Ltd. on behalf of AEHS.

  16. Lithofacies Architecturing and Hydrocarbon Reservoir Potential of Lumshiwal Formation: Surghar Range, Trans-Indus Ranges, North Pakistan

    Directory of Open Access Journals (Sweden)

    Iftikhar Alam

    2015-12-01

    directed Paleo-current system prevailed during deposition of Lumshiwal Formation. Diagenetic and tectonically induced fractures make the formation exceedingly porous and permeable as suitable reservoir horizon for the accumulation of hydrocarbon in the Trans-Indus ranges. The same formation has already been proven as potential reservoir horizon for hydrocarbon in the Kohat Plateau of northwest Pakistan. Secondly, the formation is dominantly comprised of silica/quartz sandstone (quartzarenite which can be used as silica sand, one of the essential raw materials for glass industries. The formation is also comprised of local coal seams which can be mined for production of coal in the region.

  17. A sedimentological approach to refining reservoir architecture in a mature hydrocarbon province: the Brent Province, UK North Sea

    Energy Technology Data Exchange (ETDEWEB)

    Hampson, G.J.; Sixsmith, P.J.; Johnson, H.D. [Imperial College, London (United Kingdom). Dept. of Earth Science and Engineering

    2004-04-01

    Improved reservoir characterisation in the mature Brent Province of the North Sea, aimed at maximising both in-field and near-field hydrocarbon potential, requires a clearer understanding of sub-seismic stratigraphy and facies distributions. In this context, we present a regional, high-resolution sequence stratigraphic framework for the Brent Group, UK North Sea based on extensive sedimentological re-interpretation of core and wireline-log data, combined with palynostratigraphy and published literature. This framework is used to place individual reservoirs in an appropriate regional context, thus resulting in the identification of subtle sedimentological and tectono-stratigraphic features of reservoir architecture that have been previously overlooked. We emphasise the following insights gained from our regional, high-resolution sequence stratigraphic synthesis: (1) improved definition of temporal and spatial trends in deposition both within and between individual reservoirs, (2) development of regionally consistent, predictive sedimentological models for two enigmatic reservoir intervals (the Broom and Tarbert Formations), and (3) recognition of subtle local tectono-stratigraphic controls on reservoir architecture, and their links to the regional, Middle Jurassic structural evolution of the northern North Sea. We discuss the potential applications of these insights to the identification of additional exploration potential and to improved ultimate recovery. (author)

  18. Low-maturity Kulthieth Formation coal : a possible source of polycyclic aromatic hydrocarbons in benthic sediment of the Northern Gulf of Alaska

    International Nuclear Information System (INIS)

    Van Kooten, G.K.; Short, J.W.; Kolak, J.J.

    2002-01-01

    This study addressed the issue of sources of hydrocarbons for benthic sediments in the Gulf of Alaska (GOA) with particular reference to the application of forensic geology to identify end members and to explain the geologic setting and processes affecting the system. Native coals and natural seep oils have been questioned in the past decade as possible sources of background hydrocarbons because the pattern of relative polycyclic aromatic hydrocarbon (PAH) abundance characteristic of benthic GOA sediments is inconsistent with patterns typical of weathered seep oils. Native coal has also been dismissed as a pollution source because ratios of labile hydrocarbons to total organic carbon for Bering River coal field (BRCF) sources are too low to be consistent with GOA sediments. The authors present evidence that perhaps native coal has been prematurely dismissed as a pollution source because BRCF coals do not represent adequately the geochemical signatures of coals elsewhere in the Kulthieth Formation which have much higher PAH:TOC ratios. The patterns of labile hydrocarbons in these low thermal maturity coals indicate a genetic relationship between Kulthieth Formation coals and nearby oil seeps on the Sullivan anticline. Analysis of the coal suggests it is a significant source of PAH, and it was cautioned that source models that do not include this source will underestimate the contribution of native coals to the background hydrocarbon signature in the Gulf of Alaska. 32 refs., 2 tabs., 8 figs

  19. Long-range atmospheric transport and the distribution of polycyclic aromatic hydrocarbons in Changbai Mountain.

    Science.gov (United States)

    Zhao, Xiangai; Kim, Seung-Kyu; Zhu, Weihong; Kannan, Narayanan; Li, Donghao

    2015-01-01

    The Changbai (also known as "Baekdu") Mountain, on the border between China and North Korea, is the highest mountain (2750 m) in northeastern China. Recently, this mountain region has experienced a dramatic increase in air pollution, not only because of increasing volumes of tourism-derived traffic but also because of the long-range transport of polluted westerly winds passing through major industrial and urban cities in the eastern region of China. To assess the relative importance of the two sources of pollution, 16 polycyclic aromatic hydrocarbons (PAHs) as model substances were determined in the mountain soil. A total of 32 soil samples were collected from different sides of the mountain at different latitudes between July and August of 2009. The ∑PAH concentrations were within the range 38.5-190.1 ng g(-1) on the northern side, 117.7-443.6 ng g(-1) on the southern side, and 75.3-437.3 ng g(-1) on the western side. A progressive increase in the level of ∑PAHs with latitude was observed on the southern and western sides that face the westerly wind with abundant precipitation. However, a similar concentration gradient was not observed on the northern side that receives less rain and is on the leeward direction of the wind. The high-molecular-weight PAH compounds were predominant in the soils on the southern and western sides, while low-molecular-weight PAHs dominated the northern side soils. These findings show that the distribution of PAHs in the mountain soil is strongly influenced by the atmospheric long-range transport and cold trapping. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. Hydrocarbon exploration

    Energy Technology Data Exchange (ETDEWEB)

    Lerche, I. (South Carolina Univ., Columbia, SC (United States). Dept. of Geological Sciences)

    1993-01-01

    This special issue of the journal examines various aspects of the on-going search for hydrocarbons, ranging from frontier basins where little data are available, to more mature areas where considerable data are available. The incentives underlying the search for oil are roughly: the social, economic and industrial needs of a nation; the incentive of a corporation to be profitable; and the personal incentives of individuals in the oil industry and governments, which range from financial wealth to power and which are as diverse as the individuals who are involved. From a geopolitical perspective, the needs, requirements, goals, strategies, and philosophies of nations, and groups of nations, also impact on the oil exploration game. Strategies that have been employed have ranged from boycott to austerity and rationing, to physical intervention, to global ''flooding'' with oil by over-production. (author)

  1. Enhanced thermal conduction -- An alternative solution for removing a broad range of hydrocarbons from contaminated soils

    Energy Technology Data Exchange (ETDEWEB)

    Bova, J.C.

    1999-07-01

    This paper presents an overview of Enhanced Thermal Conduction (ETC), an ex-situ soil remediation process. A review of a practical demonstration of this process which was conducted by Woodward-Clyde Consultants to determine the capability of the technology for remediating soils from gasworks sites that have been contaminated with petroleum hydrocarbons, polynuclear hydrocarbons (PAHs) and cyanide is also presented in this paper. Projections for using this process to treat soils contaminated with other hazardous materials such as TCE PCE and PCB's are discussed as well.

  2. Hydrocarbons thermal maturation: Leopatin method applied to the Parana basin; Maturacao termica de hidrocarbonetos: aplicacao do metodo de Lopatin a Bacia do Parana

    Energy Technology Data Exchange (ETDEWEB)

    Eston, Sergio Medici de; Jardim, Niza S

    1987-12-31

    One of the requirements for the existent of economic deposits of hydrocarbons is that the organic matter has undergone adequate thermal maturation. Several techniques have been proposed in order to quantity the catagenetic state of kerogen, and the Lopatin-Waples methodology permits quantification at any past time and does not require laboratory tests on samples of the material. For this reason it is an useful techniques for predicting mature zones using as basic information the thermal and subsidence histories of each stratum. Lopatin`s technique was applied to the Parana basin, with McKenzie`s crustal stretching model fitted to the data of 18 wells, and the areas predicted as mature for oil and/or gas were in good agreement with the field results. The technique predicted oil phone areas at the east border of the basin for the Ponta Grossa and Irati formation, and also that most of the thermal maturation occurred after the basalt flows of the Cretaceous period. (author) 41 refs., 6 figs., 6 tabs.

  3. Hydrocarbons thermal maturation: Leopatin method applied to the Parana basin; Maturacao termica de hidrocarbonetos: aplicacao do metodo de Lopatin a Bacia do Parana

    Energy Technology Data Exchange (ETDEWEB)

    Eston, Sergio Medici de; Jardim, Niza S.

    1986-12-31

    One of the requirements for the existent of economic deposits of hydrocarbons is that the organic matter has undergone adequate thermal maturation. Several techniques have been proposed in order to quantity the catagenetic state of kerogen, and the Lopatin-Waples methodology permits quantification at any past time and does not require laboratory tests on samples of the material. For this reason it is an useful techniques for predicting mature zones using as basic information the thermal and subsidence histories of each stratum. Lopatin`s technique was applied to the Parana basin, with McKenzie`s crustal stretching model fitted to the data of 18 wells, and the areas predicted as mature for oil and/or gas were in good agreement with the field results. The technique predicted oil phone areas at the east border of the basin for the Ponta Grossa and Irati formation, and also that most of the thermal maturation occurred after the basalt flows of the Cretaceous period. (author) 41 refs., 6 figs., 6 tabs.

  4. Selective transformation of syngas into gasoline-range hydrocarbons over mesoporous H-ZSM-5-supported cobalt nanoparticles.

    Science.gov (United States)

    Cheng, Kang; Zhang, Lei; Kang, Jincan; Peng, Xiaobo; Zhang, Qinghong; Wang, Ye

    2015-01-26

    Bifunctional Fischer-Tropsch (FT) catalysts that couple uniform-sized Co nanoparticles for CO hydrogenation and mesoporous zeolites for hydrocracking/isomerization reactions were found to be promising for the direct production of gasoline-range (C5-11 ) hydrocarbons from syngas. The Brønsted acidity results in hydrocracking/isomerization of the heavier hydrocarbons formed on Co nanoparticles, while the mesoporosity contributes to suppressing the formation of lighter (C1-4 ) hydrocarbons. The selectivity for C5-11 hydrocarbons could reach about 70 % with a ratio of isoparaffins to n-paraffins of approximately 2.3 over this catalyst, and the former is markedly higher than the maximum value (ca. 45 %) expected from the Anderson-Schulz-Flory distribution. By using n-hexadecane as a model compound, it was clarified that both the acidity and mesoporosity play key roles in controlling the hydrocracking reactions and thus contribute to the improved product selectivity in FT synthesis. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Zn-Mo/HZSM-5 Catalyst for Gasoil Range Hydrocarbon Production by Catalytic Hydrocracking of Ceiba pentandra oil

    Directory of Open Access Journals (Sweden)

    Yustia Wulandari Mirzayanti

    2018-01-01

    Full Text Available Biofuel from vegetable oil becomes one of the most suitable and logical alternatives to replace fossil fuel. The research focused on various metal ratio Zinc/Molybdenum/HZSM-5 (Zn-Mo/HZSM-5 catalyst to produce liquid hydrocarbon via catalytic hydrocracking of Ceiba penandra oil. The catalytic hydrocracking process has been applied in this study to crack Ceiba pentandra oil into a gasoil range hydrocarbon using Zn-Mo/HZSM-5 as a catalyst. The effect of various reaction temperature on the catalytic hydrocracking of Ceiba pentandra oil were studied. The Zn-Mo/HZSM-5 catalyst with metal ratio was prepared by incipient wetness impregnation method. This process used slurry pressure batch reactor with a mechanical stirrer. A series of experiments were carried out in the temperature range from 300-400 oC for 2 h at pressure between 10-15 bar. The conversion and selectivity were estimated. The liquid hydrocarbon product were identified to gasoline, kerosene, and gas oil. The results show that the use of Zn-Mo/HZSM-5 can produce gas oil as the most component in the product. Overall, the highest conversion and selectivity of gas oil range hydrocarbon was obtained when the ZnMo/HZSM-5 metal ratio was Zn(2.86 wt.%-Mo(5.32 wt.%/HZSM-5 and the name is Zn-Mo/HZSM-5_102. The highest conversion was obtained at 63.31 % and n-paraffin (gas oil range selectivity was obtained at 90.75 % at a temperature of 400 oC. Ceiba pentandra oil can be recommended as the source of inedible vegetable oil to produce gasoil as an environmentally friendly transportation fuel. Copyright © 2018 BCREC Group. All rights reserved Received: 8th September 2017; Revised: 9th September 2017; Accepted: 17th September 2017; Available online: 22nd January 2018; Published regularly: 2nd April 2018 How to Cite: Mirzayanti, Y.W., Kurniawansyah, F., Prajitno, D.H., Roesyadi, A. (2018. Zn-Mo/HZSM-5 Catalyst for Gasoil Range Hydrocarbon Production by Catalytic Hydrocracking of Ceiba pentandra

  6. Detection of radiation-induced hydrocarbons in Camembert irradiated before and after the maturing process-comparison of florisil column chromatography and on-line coupled liquid chromatography-gas chromatography

    International Nuclear Information System (INIS)

    Schulzki, G.; Spiegelberg, A.; Bögl, K.W.; Schreiber, G.A.

    1995-01-01

    The influence of the maturing process on the detection of radiation-induced volatile hydrocarbons in the fat of Camembert has been investigated. Two analytical methods for separation of the hydrocarbon fraction from the lipid were applied: Florisil column chromatography with subsequent gas chromatographic-mass spectrometric (GC-MS) determination as well as on-line coupled liquid chromatography-GC-MS. The maturing process had no influence on the detection of radiation-induced volatiles. Comparable results were achieved with both analytical methods. However, preference is given to the more effective on-line coupled LC-GC method

  7. Production of Jet Fuel-Range Hydrocarbons from Hydrodeoxygenation of Lignin over Super Lewis Acid Combined with Metal Catalysts.

    Science.gov (United States)

    Wang, Hongliang; Wang, Huamin; Kuhn, Eric; Tucker, Melvin P; Yang, Bin

    2018-01-10

    Super Lewis acids containing the triflate anion [e.g., Hf(OTf) 4 , Ln(OTf) 3 , In(OTf) 3 , Al(OTf) 3 ] and noble metal catalysts (e.g., Ru/C, Ru/Al 2 O 3 ) formed efficient catalytic systems to generate saturated hydrocarbons from lignin in high yields. In such catalytic systems, the metal triflates mediated rapid ether bond cleavage through selective bonding to etheric oxygens while the noble metal catalyzed subsequent hydrodeoxygenation (HDO) reactions. Near theoretical yields of hydrocarbons were produced from lignin model compounds by the combined catalysis of Hf(OTf) 4 and ruthenium-based catalysts. When a technical lignin derived from a pilot-scale biorefinery was used, more than 30 wt % of the hydrocarbons produced with this catalytic system were cyclohexane and alkylcyclohexanes in the jet fuel range. Super Lewis acids are postulated to strongly interact with lignin substrates by protonating hydroxyl groups and ether linkages, forming intermediate species that enhance hydrogenation catalysis by supported noble metal catalysts. Meanwhile, the hydrogenation of aromatic rings by the noble metal catalysts can promote deoxygenation reactions catalyzed by super Lewis acids. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Production of Jet Fuel-Range Hydrocarbons from Hydrodeoxygenation of Lignin over Super Lewis Acid Combined with Metal Catalysts

    International Nuclear Information System (INIS)

    Wang, Hongliang; Wang, Huamin; Kuhn, Eric; Tucker, Melvin P.; Yang, Bin

    2017-01-01

    Super Lewis acids containing the triflate anion [e.g., Hf(OTf) 4 , Ln(OTf) 3 , In(OTf) 3 , Al(OTf) 3 ] and noble metal catalysts (e.g., Ru/C, Ru/Al2O 3 ) formed efficient catalytic systems to generate saturated hydrocarbons from lignin in high yields. In such catalytic systems, the metal triflates mediated rapid ether bond cleavage through selective bonding to etheric oxygens while the noble metal catalyzed subsequent hydrodeoxygenation (HDO) reactions. Near theoretical yields of hydrocarbons were produced from lignin model compounds by the combined catalysis of Hf(OTf)4 and ruthenium-based catalysts. When a technical lignin derived from a pilot-scale biorefinery was used, more than 30 wt % of the hydrocarbons produced with this catalytic system were cyclohexane and alkylcyclohexanes in the jet fuel range. Super Lewis acids are postulated to strongly interact with lignin substrates by protonating hydroxyl groups and ether linkages, forming intermediate species that enhance hydrogenation catalysis by supported noble metal catalysts. Meanwhile, the hydrogenation of aromatic rings by the noble metal catalysts can promote oxygenation reactions catalyzed by super Lewis acids.

  9. Production of Jet Fuel-Range Hydrocarbons from Hydrodeoxygenation of Lignin over Super Lewis Acid Combined with Metal Catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Hongliang [Department of Biological Systems Engineering, Washington State University, Richland WA 99354 USA; Current address: Center of Biomass Engineering/College of Agronomy and Biotechnology, China Agricultural University, Beijing 100193 PR China; Wang, Huamin [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Kuhn, Eric [National Bioenergy Center, National Renewable Energy Laboratory, 15013 Denver West Parkway Golden CO 80401 USA; Tucker, Melvin P. [National Bioenergy Center, National Renewable Energy Laboratory, 15013 Denver West Parkway Golden CO 80401 USA; Yang, Bin [Department of Biological Systems Engineering, Washington State University, Richland WA 99354 USA

    2017-11-14

    Super Lewis acids containing the triflate anion (e.g. Hf(OTf)4, Ln(OTf)3, Al(OTf)3) and noble metal catalysts (e.g. Ru/C, Ru/Al2O3) formed efficient catalytic systems to generate saturated hydrocarbons from lignin in high yields. In such catalytic systems, the metal triflates mediated rapid ether bond cleavage via selective bonding to etheric oxygens while the noble metal catalysed subsequent hydrodeoxygenation (HDO) reactions. Near theoretical yields of hydrocarbons were produced from lignin model compounds by the combined catalysis of Hf(OTf)4 and ruthenium-based catalysts. When a technical lignin derived from a pilot-scale biorefinery was used, more than 30 wt% of the hydrocarbons produced with this catalytic system were cyclohexane and alkylcyclohexanes in the jet fuel range. Super Lewis acids are postulated to strongly interact with lignin substrates via protonating hydroxyls and ether linkages, forming intermediate species that enhance hydrogenation catalysis by supported noble metal catalysts. Meanwhile, the hydrogenation of aromatic rings by the noble metal catalysts can promote oxygenation reactions catalysed by super Lewis acids.

  10. Versatile transformations of hydrocarbons in anaerobic bacteria: substrate ranges and regio- and stereo-chemistry of activation reactions†

    Science.gov (United States)

    Jarling, René; Kühner, Simon; Basílio Janke, Eline; Gruner, Andrea; Drozdowska, Marta; Golding, Bernard T.; Rabus, Ralf; Wilkes, Heinz

    2015-01-01

    Anaerobic metabolism of hydrocarbons proceeds either via addition to fumarate or by hydroxylation in various microorganisms, e.g., sulfate-reducing or denitrifying bacteria, which are specialized in utilizing n-alkanes or alkylbenzenes as growth substrates. General pathways for carbon assimilation and energy gain have been elucidated for a limited number of possible substrates. In this work the metabolic activity of 11 bacterial strains during anaerobic growth with crude oil was investigated and compared with the metabolite patterns appearing during anaerobic growth with more than 40 different hydrocarbons supplied as binary mixtures. We show that the range of co-metabolically formed alkyl- and arylalkyl-succinates is much broader in n-alkane than in alkylbenzene utilizers. The structures and stereochemistry of these products are resolved. Furthermore, we demonstrate that anaerobic hydroxylation of alkylbenzenes does not only occur in denitrifiers but also in sulfate reducers. We propose that these processes play a role in detoxification under conditions of solvent stress. The thermophilic sulfate-reducing strain TD3 is shown to produce n-alkylsuccinates, which are suggested not to derive from terminal activation of n-alkanes, but rather to represent intermediates of a metabolic pathway short-cutting fumarate regeneration by reverse action of succinate synthase. The outcomes of this study provide a basis for geochemically tracing such processes in natural habitats and contribute to an improved understanding of microbial activity in hydrocarbon-rich anoxic environments. PMID:26441848

  11. Selective Synthesis of Gasoline-Ranged Hydrocarbons from Syngas over Hybrid Catalyst Consisting of Metal-Loaded ZSM-5 Coupled with Copper-Zinc Oxide

    Directory of Open Access Journals (Sweden)

    Ting Ma

    2014-04-01

    Full Text Available The conversion of syngas (CO + H2 to gasoline-ranged hydrocarbons was carried out using a hybrid catalyst consisting of metal-loaded ZSM-5 coupled with Cu-ZnO in a near-critical n-hexane solvent. Methanol was synthesized from syngas over Cu-ZnO; subsequently, was converted to hydrocarbons through the formation of dimethyl ether (DME over the metal-loaded ZSM-5. When 0.5 wt% Pd/ZSM-5 and 5 wt% Cu/ZSM-5 among the metal-loaded ZSM-5 catalysts with Pd, Co, Fe or Cu were employed as a portion of the hybrid catalyst, the gasoline-ranged hydrocarbons were selectively produced (the gasoline-ranged hydrocarbons in all hydrocarbons: 59% for the hybrid catalyst with Pd/ZSM-5 and 64% for that with Cu/ZSM-5 with a similar CO conversion during the reaction. An increase in the Cu loading on ZSM-5 resulted in increasing the yield of the gasoline-ranged hydrocarbons, and in decreasing the yield of DME. Furthermore, the hybrid catalyst with Cu/ZSM-5 exhibited no deactivation for 30 h of the reaction. It was revealed that a hybrid catalyst containing Cu/ZSM-5 was efficient in the selective synthesis of gasoline-ranged hydrocarbons from syngas via methanol in the near-critical n-hexane fluid.

  12. Unraveling the Timing of Fluid Migration and Trap Formation in the Brooks Range Foothills: A Key to Discovering Hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Catherine L. Hanks

    2008-12-31

    Naturally occurring fractures can play a key role in the evolution and producibility of a hydrocarbon accumulation. Understanding the evolution of fractures in the Brooks Range/Colville basin system of northern Alaska is critical to developing a better working model of the hydrocarbon potential of the region. This study addressed this problem by collecting detailed and regional data on fracture distribution and character, structural geometry, temperature, the timing of deformation along the Brooks Range rangefront and adjacent parts of the Colville basin, and the in situ stress distribution within the Colville basin. This new and existing data then were used to develop a model of how fractures evolved in northern Alaska, both spatially and temporally. The results of the study indicate that fractures formed episodically throughout the evolution of northern Alaska, due to a variety of mechanisms. Four distinct fracture sets were observed. The earliest fractures formed in deep parts of the Colville basin and in the underlying Ellesmerian sequence rocks as these rocks experienced compression associated with the growing Brooks Range fold-and-thrust belt. The orientation of these deep basin fractures was controlled by the maximum in situ horizontal stress in the basin at the time of their formation, which was perpendicular to the active Brooks Range thrust front. This orientation stayed consistently NS-striking for most of the early history of the Brooks Range and Colville basin, but changed to NW-striking with the development of the northeastern Brooks Range during the early Tertiary. Subsequent incorporation of these rocks into the fold-and-thrust belt resulted in overprinting of these deep basin fractures by fractures caused by thrusting and related folding. The youngest fractures developed as rocks were uplifted and exposed. While this general order of fracturing remains consistent across the Brooks Range and adjacent Colville basin, the absolute age at any one

  13. The organic petrology and thermal maturity of Lower Carboniferous and Upper Devonian source rocks in the Liard Basin, at Jackfish Gap-Yohin Ridge and North Beaver River, northern Canada: Implications for hydrocarbon exploration

    Energy Technology Data Exchange (ETDEWEB)

    Potter, J. (Univ. of Newcastle-upon-Tyne (United Kingdom)); Richards, B.C.; Goodarzi, G. (Geological Survey, Calgary, Alberta (Canada))

    Basinal shales of the Besa River Fm. have TOC values ranging from 1 to 4% and contain abundant type II, dominantly amorphous, kerogen of marine origin. Shales in the Yohin, Clausen, Prophet, and Golata Formations are of mixed maring and terrestrial origins and yield TOC values of 1 to 3%. Kerogen in the Golata and Yohin Formations are dominated by terrestrial components, while the Clausen and Flett kerogen comprises marine liptinites and bitumens. Kerogen from the deltaic Mattson shales at Jackfish Gap are types II and III, having mixed marine and terrestrial origins consistent with shallow, nearshore, subtidal environments. The coals are sapropelic and probably lacustrine in origin. Algal laminites associated with coals in the Upper Mattson have >10% TOC values, while non-laminite shales contain between 2 and 5% TOC. Comparable measured and calculated vitrinite reflectance data indicate that kerogen in the Lower Carboniferous at Jackfish Gap is mature. Kerogen in correlative formations in the subsurface at North Beaver River is more marine. Vitrinites are rate and oxidized, but four populations of bitumens are distinguished on the basis of relative reflectivity and morphological or petrophysical associations. Types A and B bitumens are primary and by-products of hydrocarbon generation from type II (algal and amorphous) kerogens. Correlations between depth and reflectance of bitumens A and B are very good. Vitrinite reflectance data calculated from bitumen reflectance measurements for the Besa River, Prophet, and Golata indicate that they are potential sources of catagenic gas. The Mattson kerogen is mature, oil and gas-prone.

  14. Detection of arsenic-containing hydrocarbons in a range of commercial fish oils by GC-ICPMS analysis

    DEFF Research Database (Denmark)

    Sele, Veronika; Amlund, Heidi; Berntssen, Marc H. G.

    2013-01-01

    The present study describes the use of a simple solid-phase extraction procedure for the extraction of arsenic-containing hydrocarbons from fish oil followed by analysis using gas chromatography (GC) coupled to inductively coupled plasma mass spectrometry (ICPMS). The procedure permitted the anal......The present study describes the use of a simple solid-phase extraction procedure for the extraction of arsenic-containing hydrocarbons from fish oil followed by analysis using gas chromatography (GC) coupled to inductively coupled plasma mass spectrometry (ICPMS). The procedure permitted...... the analysis of a small sample amount, and the method was applied on a range of different commercial fish oils, including oils of anchovy (Engraulis ringens), Atlantic herring (Clupea harengus), sand eel (Ammodytes marinus), blue whiting (Micromesistius poutassou) and a commercial mixed fish oil (mix of oils...... of Atlantic herring, Atlantic cod (Gadus morhua) and saithe (Pollachius virens)). Total arsenic concentrations in the fish oils and in the extracts of the fish oils were determined by microwave-assisted acid digestion and ICPMS. The arsenic concentrations in the fish oils ranged from 5.9 to 8.7 mg kg-1. Three...

  15. Reference range levels of polycyclic aromatic hydrocarbons in the US population by measurement of urinary monohydroxy metabolites

    International Nuclear Information System (INIS)

    Grainger, James; Huang, Wenlin; Patterson, Donald G.; Turner, Wayman E.; Pirkle, James; Caudill, Samuel P.; Wang, Richard Y.; Needham, Larry L.; Sampson, Eric J.

    2006-01-01

    We developed a gas chromatography isotope-dilution high-resolution mass spectrometry (GC/Id-HRMS) method for measuring 14 polycyclic aromatic hydrocarbon (PAH) metabolites representing seven parent PAHs in 3 mL of urine at low parts-per-trillion levels. PAH levels were determined in urine samples collected in 1999 and 2000 from approximately 2400 participants in the National Health and Nutrition Examination Survey, and, for the first time, reference range values were calculated for these metabolites in the US population. Using this GC/ID-HRMS method, we found detectable concentrations for monohydroxy metabolite isomers of fluorene, phenanthrene, fluoranthene, pyrene, and chrysene, benzo[c]phenanthrene, and benz[a]anthracene. Some monohydroxy metabolite isomers of benzo[c]phenanthrene, chrysene, and benz[a]anthracene exhibited low detection frequencies that did not allow for geometric mean calculations. Our study results enabled us to establish a reference range for the targeted PAHs in the general US population

  16. The effect of mature elephant bull introductions on ranging patterns of resident bulls: Phinda Private Game Reserve, South Africa

    Directory of Open Access Journals (Sweden)

    Heleen Druce

    2006-12-01

    Full Text Available Increasing popularity of wildlife viewing has resulted in a rapid increase in small, enclosed reserves in South Africa. The African elephant is one of the many species that has been reintroduced into these reserves for eco-tourism. These elephant populations were established as young (smaller that 10 years old orphans from prior Kruger National Park culling operations. Consequently, this abnormal sex and age structure of these introduced populations has influenced their behavioural and spatial ecology. In Pilanesberg National Park, this abnormal behaviour was corrected by introducing older bulls and culling certain problem elephants. In July 2003, three older bulls (29–41 years old were introduced into Phinda Private Game Reserve, KwaZulu-Natal, South Africa in order to normalise the bull age structure. These introduced bulls were monitored intensively after release, as was the resident bull population, both before and after introduction of the older bulls. The introduced bulls settled into restricted ranges separate from the family groups. All the resident bulls decreased their home ranges at first, with most increasing their home ranges a year later. The resident bulls’ change in ranging patterns was due more to ecological factors than to the influence of the mature bull introduction. This study indicates that the introduction of older male elephants into small populations does not pose major risks or animal welfare concerns.

  17. Polycyclic aromatic hydrocarbons - fate and long-range atmospheric transport studied using a global model, EMAC-SVOC

    Science.gov (United States)

    Octaviani, Mega; Tost, Holger; Lammel, Gerhard

    2017-04-01

    Polycyclic aromatic hydrocarbons (PAHs) are emitted by incomplete combustion from fossil fuel, vehicles, and biomass burning. They may persist in environmental compartments, pose a health hazard and may bio accumulate along food chains. The ECHAM/MESSy Atmospheric Chemistry (EMAC) model had been used to simulate global tropospheric, stratospheric chemistry and climate. In this study, we improve the model to include simulations of the transport and fate of semi-volatile organic compounds (SVOC). The EMAC-SVOC model takes into account essential environmental processes including gas-particle partitioning, dry and wet deposition, chemical and bio-degradation, and volatilization from sea surface, soils, vegetation, and snow. The model was evaluated against observational data in the Arctic, mid-latitudes, and tropics, and further applied to study total environmental lifetime and long-range transport potential (LRTP) of PAHs. We selected four compounds for study, spanning a wide range of volatility, i.e., phenanthrene, fluoranthene, pyrene, and benzo[a]pyrene. Several LRTP indicators were investigated, including the Arctic contamination potential, meridional spreading, and zonal and meridional fluxes to remote regions.

  18. Global long-range transport and lung cancer risk from polycyclic aromatic hydrocarbons shielded by coatings of organic aerosol

    Science.gov (United States)

    Shrivastava, Manish; Lou, Silja; Zelenyuk, Alla; Easter, Richard C.; Corley, Richard A.; Thrall, Brian D.; Rasch, Philip J.; Fast, Jerome D.; Massey Simonich, Staci L.; Shen, Huizhong; Tao, Shu

    2017-02-01

    Polycyclic aromatic hydrocarbons (PAHs) have toxic impacts on humans and ecosystems. One of the most carcinogenic PAHs, benzo(a)pyrene (BaP), is efficiently bound to and transported with atmospheric particles. Laboratory measurements show that particle-bound BaP degrades in a few hours by heterogeneous reaction with ozone, yet field observations indicate BaP persists much longer in the atmosphere, and some previous chemical transport modeling studies have ignored heterogeneous oxidation of BaP to bring model predictions into better agreement with field observations. We attribute this unexplained discrepancy to the shielding of BaP from oxidation by coatings of viscous organic aerosol (OA). Accounting for this OA viscosity-dependent shielding, which varies with temperature and humidity, in a global climate/chemistry model brings model predictions into much better agreement with BaP measurements, and demonstrates stronger long-range transport, greater deposition fluxes, and substantially elevated lung cancer risk from PAHs. Model results indicate that the OA coating is more effective in shielding BaP in the middle/high latitudes compared with the tropics because of differences in OA properties (semisolid when cool/dry vs. liquid-like when warm/humid). Faster chemical degradation of BaP in the tropics leads to higher concentrations of BaP oxidation products over the tropics compared with higher latitudes. This study has profound implications demonstrating that OA strongly modulates the atmospheric persistence of PAHs and their cancer risks.

  19. Global long-range transport and lung cancer risk from polycyclic aromatic hydrocarbons shielded by coatings of organic aerosol

    Energy Technology Data Exchange (ETDEWEB)

    Shrivastava, ManishKumar B.; Lou, Sijia; Zelenyuk-Imre, Alla; Easter, Richard C.; Corley, Richard A.; Thrall, Brian D.; Rasch, Philip J.; Fast, Jerome D.; Massey Simonich, Staci L.; Shen, Huizhong; Tao, Shu

    2017-01-23

    Polycyclic aromatic hydrocarbons (PAHs) have toxic impacts on ecosystems and human health. Laboratory measurements show that one of the most carcinogenic PAHs, benzo(a)pyrene, which is adsorbed on surfaces of soot particles, reacts very quickly with atmospheric oxidants like ozone within ~2 hours. Yet, field observations indicate that it actually persists for much longer periods in the atmosphere, and this large discrepancy is not well understood. Driven by novel experimental understanding, we develop a new modelling approach, whereby particle-bound BaP is shielded from oxidation by a coating of viscous organic aerosol (OA). We show that application of this new approach in a global climate model leads to higher atmospheric BaP concentrations that agree much better with measurements, compared to the default model, as well as stronger long-range transport and greater deposition fluxes. This new approach also predicts elevated lung-cancer risk from PAHs. Predicted oxidation of BaP is highest over a tropical belt where OA is liquid-like.

  20. Syngas Conversion to Gasoline-Range Hydrocarbons over Pd/ZnO/Al2O3 and ZSM-5 Composite Catalyst System

    Energy Technology Data Exchange (ETDEWEB)

    Dagle, Robert A.; Lizarazo Adarme, Jair A.; Lebarbier, Vanessa MC; Gray, Michel J.; White, James F.; King, David L.; Palo, Daniel R.

    2014-07-01

    A composite Pd/ZnO/Al2O3-HZSM-5 (Si/Al=40) catalytic system was evaluated for the synthesis of gasoline-range hydrocarbons directly from synthesis gas. Bifunctional catalyst comprising PdZn metal and acid sites present the required catalytically active sites necessary for the methanol synthesis, methanol dehydration, and methanol-to-gasoline reactions. This system provides a unique catalytic pathway for the production of liquid hydrocarbons directly from syngas. However, selectivity control is difficult and poses many challenges. The composite catalytic system was evaluated under various process conditions. Investigated were the effects of temperature (310-375oC), pressure (300-1000 psig), time-on-stream (50 hrs), and gas-hour space velocity (740-2970 hr-1), using a H2/CO molar syngas ratio of 2.0. By operating at the lower end of the temperature range investigated, liquid hydrocarbon formation was favored, as was decreased amounts of undesirable light hydrocarbons. However, lower operating temperatures also facilitated undesirable CO2 formation via the water-gas shift reaction. Higher operating pressures slightly favored liquid synthesis. Operating at relatively low pressures (e.g. 300 psig) was made possible, whereas for methanol synthesis alone higher pressure are usually required to achieve similar conversion levels (e.g. 1000 psig). Thermodynamic constraints on methanol synthesis are eased by pushing the equilibrium through hydrocarbon formation. Catalytic performance was also evaluated by altering Pd and Zn composition of the Pd/ZnO/Al2O3 catalyst. Of the catalysts and conditions tested, selectivity toward liquid hydrocarbon was highest when using a 5% Pd metal loading and Pd/Zn molar ratio of 0.25 and mixed with HZMS-5, operating at 310oC and 300 psig, CO conversion was 43 % and selectivity (carbon weight basis) to hydrocarbons was 49 wt. %. Of the hydrocarbon fraction, 44wt. % was in the C5-C12 liquid product range and consisted primarily of aromatic

  1. High performance direct absorption spectroscopy of pure and binary mixture hydrocarbon gases in the 6-11 μm range

    Science.gov (United States)

    Heinrich, Robert; Popescu, Alexandru; Hangauer, Andreas; Strzoda, Rainer; Höfling, Sven

    2017-08-01

    The availability of accurate and fast hydrocarbon analyzers, capable of real-time operation while enabling feedback-loops, would lead to a paradigm change in the petro-chemical industry. Primarily gas chromatographs measure the composition of hydrocarbon process streams. Due to sophisticated gas sampling, these analyzers are limited in response time. As hydrocarbons absorb in the mid-infrared spectral range, the employment of fast spectroscopic systems is highly attractive due to significantly reduced maintenance costs and the capability to setup real-time process control. New developments in mid-infrared laser systems pave the way for the development of high-performance analyzers provided that accurate spectral models are available for multi-species detection. In order to overcome current deficiencies in the availability of spectroscopic data, we developed a laser-based setup covering the 6-11 μm wavelength range. The presented system is designated as laboratory reference system. Its spectral accuracy is at least 6.6× 10^{-3} cm^{-1} with a precision of 3× 10^{-3} cm^{-1}. With a "per point" minimum detectable absorption of 1.3× 10^{-3} cm^{-1} Hz^{{-}{1/2}} it allows us to perform systematic measurements of hydrocarbon spectra of the first 7 alkanes under conditions which are not tabulated in spectroscopic database. We exemplify the system performance with measured direct absorption spectra of methane, propane, iso-butane, and a mixture of methane and propane.

  2. Jet-Fuel Range Hydrocarbons from Biomass-Derived Sorbitol over Ni-HZSM-5/SBA-15 Catalyst

    Directory of Open Access Journals (Sweden)

    Yujing Weng

    2015-12-01

    Full Text Available Aromatics and cyclic-hydrocarbons are the significant components of jet fuel with high energy-density. However, conventional technologies for bio-fuel production cannot produce these products without further aromatization and isomerization. In this work, renewable liquid fuel with high content of aromatics and cyclic-hydrocarbons was obtained through aqueous catalytic conversion of biomass sorbitol over Ni-HZSM-5/SBA-15 catalyst. Texture characteristics of the catalyst were determined by physisorption of N2, which indicated its bimodal pore structures were microporous (HZSM-5, pore width: 0.56 nm and mesoporous (SBA-15, pore width: 8 nm. The surface acidity included weak and strong acid sites, predominantly Lewis type, and was further confirmed by the NH3-TPD and Py-IR analysis. The catalytic performances were tested in a fixed-bed reactor under the conditions of 593 K, WHSV of 0.75 h−1, GHSV of 2500 h−1 and 4.0 MPa of hydrogen pressure, whereby oil yield of 40.4 wt. % with aromatics and cyclic-hydrocarbons content of 80.0% was obtained.

  3. Task 8: Evaluation of hydrocarbon potential

    International Nuclear Information System (INIS)

    Cashman, P.H.; Trexler, J.H. Jr.

    1994-01-01

    Our studies focus on the stratigraphy of Late Devonian to early Pennsylvanian rocks at the NTS, because these are the best potential hydrocarbon source rocks in the vicinity of Yucca Mountain. In the last year, our stratigraphic studies have broadened to include the regional context for both the Chainman and the Eleana formations. New age data based on biostratigraphy constrain the age ranges of both Chainman and Eleana; accurate and reliable ages are essential for regional correlation and for regional paleogeographic reconstructions. Source rock analyses throughout the Chainman establish whether these rocks contained adequate organic material to generate hydrocarbons. Maturation analyses of samples from the Chainman determine whether the temperature history has been suitable for the generation of liquid hydrocarbons. Structural studies are aimed at defining the deformation histories and present position of the different packages of Devonian - Pennsylvanian rocks. This report summarizes new results of our structural, stratigraphic and hydrocarbon source rock potential studies at the Nevada Test Site and vicinity. Stratigraphy is considered first, with the Chainman Shale and Eleana Formation discussed separately. New biostratigraphic results are included in this section. New results from our structural studies are summarized next, followed by source rock and maturation analyses of the Chainman Shale. Directions for future work are included where appropriate

  4. Aromatic hydrocarbons

    International Nuclear Information System (INIS)

    Roder, M.

    1985-01-01

    Papers dealing with radiolysis of aromatic hydrocarbons of different composition (from benzene to terphenyls and hydrocarbons with condensed rings) as well as their mixtures (with alkanes, alkenes, other aromatic hydrocarbons) are reviewed. High radiation stability of aromatic hydrocarbons in condensed phases associated with peculiarities of molecular structure of compounds is underlined. Mechanisms of radiolytic processes, vaues of product yields are considered

  5. Measurements of ozone and nonmethane hydrocarbons at Chichi-jima island, a remote island in the western Pacific: long-range transport of polluted air from the Pacific rim region

    Science.gov (United States)

    Kato, Shungo; Pochanart, Pakpong; Kajii, Yoshizumi

    Chichi-jima island is located in the Pacific about 1000 km from the Japanese main island and is an ideal remote observatory from which to assess the long-range transport of polluted air from East Asia. The ozone concentration was measured from August 1997 to August 1998. Owing to the air mass change, the seasonal variation of ozone shows a distinct character: low concentration (about 13 ppbv) for the maritime air mass during the summer, and high concentration (about 40 ppbv) for the continental air mass during the winter. To assess the contribution of the long-range transport of polluted air during winter, nonmethane hydrocarbons were also measured in December 1999. Using backward trajectory analysis, the transport time of the air mass from the source area in the Pacific rim region was calculated for each sample. The concentration of hydrocarbons shows a clear negative correlation against the transport time. This analysis clearly shows the transport of polluted air, emitted in East Asia, to the Pacific during the winter. The plots of suitable hydrocarbon pairs showed that the decrease of hydrocarbon concentrations during winter is mainly caused by the mixing with clean background air.

  6. Resolving model parameter values from carbon and nitrogen stock measurements in a wide range of tropical mature forests using nonlinear inversion and regression trees

    Science.gov (United States)

    Shuguang Liua; Pamela Anderson; Guoyi Zhoud; Boone Kauffman; Flint Hughes; David Schimel; Vicente Watson; Joseph. Tosi

    2008-01-01

    Objectively assessing the performance of a model and deriving model parameter values from observations are critical and challenging in landscape to regional modeling. In this paper, we applied a nonlinear inversion technique to calibrate the ecosystem model CENTURY against carbon (C) and nitrogen (N) stock measurements collected from 39 mature tropical forest sites in...

  7. A study of light hydrocarbons (C{sub 4}-C{sub 1}3) in source rocks and petroleum fluid

    Energy Technology Data Exchange (ETDEWEB)

    Odden, Wenche

    2000-07-01

    This thesis consists of an introduction and five included papers. Of these, four papers are published in international journals and the fifth was submitted for review in April 2000. Emphasis has been placed on both naturally and artificially generated light hydrocarbons in petroleum fluids and their proposed source rocks as well as direct application of light hydrocarbons to oil/source rock correlations. Collectively, these papers describe a strategy for interpreting the source of the light hydrocarbons in original oils and condensates as well as the source of the asphaltene fractions from the reservoir fluids. The influence of maturity on light hydrocarbon composition has also been evaluated. The papers include (1) compositional data on the light hydrocarbons from thermal extracts and kerogen pyrolysates of sediment samples, (2) light hydrocarbon data of oils and condensates as well as the pyrolysis products of the asphaltenes from these fluids, (3) assessment of compositional alteration effects, such as selective losses of light hydrocarbons due to evaporation, thermal maturity, phase fractionation and biodegradation, (4) comparison of naturally and artificially generated light hydrocarbons, and (5) compound-specific carbon isotope analysis of the whole range of hydrocarbons of all sample types. (author)

  8. CSDA range, stopping power and mean penetration depth energy relationships in some hydrocarbons and biologic materials for 10 eV to 100 MeV with the modified Rohrlich-Carlson model

    Energy Technology Data Exchange (ETDEWEB)

    Guemues, Hasan [Ondokuz Mayis University, Department of Physics, Faculty of Sciences and Arts, Samsun (Turkey); Bentabet, Abdelouahab [Bordj Bou Arreridj University, LCVRN, SNVSTU Faculty, El Anasser (Algeria)

    2017-05-15

    In this study, for some hydrocarbons and biological compounds, stopping power formula are presented, being valid for low and intermediate electron energies. In addition, calculation of the continuous slowing down approximation range (CSDA range) from the stopping power is also made. Calculation of the CSDA range for some hydrocarbons: C{sub 2}H{sub 6} (ethane), C{sub 4}H{sub 10} (butane), C{sub 6}H{sub 14} (hexane) C{sub 8}H{sub 18} (octane), C{sub 5}H{sub 5}N{sub 5} (adenine) and C{sub 5}H{sub 5}N{sub 5}O (guanine) have been introduced for incident electrons in the energy range 30 eV to 1 MeV. The range of electrons has been calculated within the continuous slowing down approximation (CSDA) using modified Rohrlich and Carlson formula of stopping power. Besides, we have calculated the mean penetration depths using a spherical geometric model developed by Bentabet (Vacuum 86:1855-1859, 35). The results have been compared with the other theoretical results, Monte Carlo code such as PENELOPE predictions and semi-empirical results. The calculated results of CSDA ranges for electrons in the energy range from 20 eV to 100 MeV are found to be in good agreement to within 10% with available date. (orig.)

  9. ORGANIZATIONAL PROJECT MANAGEMENT MATURITY

    Directory of Open Access Journals (Sweden)

    Yana Derenskaya

    2017-11-01

    Full Text Available The present article is aimed at developing a set of recommendations for achieving a higher level of organizational project maturity at a given enterprise. Methodology. For the purposes of the current research, the available information sources on the components of project management system are analysed; the essence of “organizational maturity” and the existing models of organizational maturity are studied. The method of systemic and structural analysis, as well as the method of logical generalization, are employed in order to study the existing models of organizational maturity, to describe levels of organizational maturity, and finally to develop a set of methodological recommendations for achieving a higher level of organizational project maturity at a given enterprise. The results of the research showed that the core elements of project management system are methodological, organizational, programtechnical, and motivational components. Project management encompasses a wide range of issues connected with organizational structure, project team, communication management, project participants, etc. However, the fundamental basis for developing project management concept within a given enterprise starts with defining its level of organizational maturity. The present paper describes various models of organizational maturity (staged, continuous, petal-shaped and their common types (H. Кеrzner Organizational Maturity Model, Berkeley PM Maturity Model, Organizational Project Management Maturity Model, Portfolio, Program & Project Management Maturity Model. The analysis of available theoretic works showed that the notion “organizational project maturity” refers to the capability of an enterprise to select projects and manage them with the intention of achieving its strategic goals in the most effective way. Importantly, the level of maturity can be improved by means of formalizing the acquired knowledge, regulating project-related activities

  10. Petroleum hydrocarbons

    International Nuclear Information System (INIS)

    Farrington, J.W.; Teal, J.M.; Parker, P.L.

    1976-01-01

    Methods for analysis of petroleum hydrocarbons in marine samples are presented. Types of hydrocarbons present and their origins are discussed. Principles and methods of analysis are outlined. Infrared spectrometry, uv spectrometry, gas chromatography, mass spectroscopy, and carbon 14 measurements are described

  11. Distributions of Polycyclic Aromatic Hydrocarbons, Aromatic Ketones, Carboxylic Acids, and Trace Metals in Arctic Aerosols: Long-Range Atmospheric Transport, Photochemical Degradation/Production at Polar Sunrise.

    Science.gov (United States)

    Singh, Dharmendra Kumar; Kawamura, Kimitaka; Yanase, Ayako; Barrie, Leonard A

    2017-08-15

    The distributions, correlations, and source apportionment of aromatic acids, aromatic ketones, polycyclic aromatic hydrocarbons (PAHs), and trace metals were studied in Canadian high Arctic aerosols. Nineteen PAHs including minor sulfur-containing heterocyclic PAH (dibenzothiophene) and major 6 carcinogenic PAHs were detected with a high proportion of fluoranthene followed by benzo[k]fluoranthene, pyrene, and chrysene. However, in the sunlit period of spring, their concentrations significantly declined likely due to photochemical decomposition. During the polar sunrise from mid-March to mid-April, benzo[a]pyrene to benzo[e]pyrene ratios significantly dropped, and the ratios diminished further from late April to May onward. These results suggest that PAHs transported over the Arctic are subjected to strong photochemical degradation at polar sunrise. Although aromatic ketones decreased in spring, concentrations of some aromatic acids such as benzoic and phthalic acids increased during the course of polar sunrise, suggesting that aromatic hydrocarbons are oxidized to result in aromatic acids. However, PAHs do not act as the major source for low molecular weight (LMW) diacids such as oxalic acid that are largely formed at polar sunrise in the arctic atmosphere because PAHs are 1 to 2 orders of magnitude less abundant than LMW diacids. Correlations of trace metals with organics, their sources, and the possible role of trace transition metals are explained.

  12. The marine bacterium Marinobacter hydrocarbonoclasticus SP17 degrades a wide range of lipids and hydrocarbons through the formation of oleolytic biofilms with distinct gene expression profiles.

    Science.gov (United States)

    Mounier, Julie; Camus, Arantxa; Mitteau, Isabelle; Vaysse, Pierre-Joseph; Goulas, Philippe; Grimaud, Régis; Sivadon, Pierre

    2014-12-01

    Hydrophobic organic compounds (mainly lipids and hydrocarbons) represent a significant part of the organic matter in marine waters, and their degradation has an important impact in the carbon fluxes within oceans. However, because they are nearly insoluble in the water phase, their degradation by microorganisms occurs at the interface with water and thus requires specific adaptations such as biofilm formation. We show that Marinobacter hydrocarbonoclasticus SP17 develops biofilms, referred to as oleolytic biofilms, on a large variety of hydrophobic substrates, including hydrocarbons, fatty alcohols, fatty acids, triglycerides, and wax esters. Microarray analysis revealed that biofilm growth on n-hexadecane or triolein involved distinct genetic responses, together with a core of common genes that might concern general mechanisms of biofilm formation. Biofilm growth on triolein modulated the expression of hundreds of genes in comparison with n-hexadecane. The processes related to primary metabolism and genetic information processing were downregulated. Most of the genes that were overexpressed on triolein had unknown functions. Surprisingly, their genome localization was restricted to a few regions identified as putative genomic islands or mobile elements. These results are discussed with regard to the adaptive responses triggered by M. hydrocarbonoclasticus SP17 to occupy a specific niche in marine ecosystems. © 2014 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

  13. Certification of a second series of five hydrocarbon materials for the determination of equilibrium flashpoint (temperature ranges -10/sup 0/C to +5/sup 0/C and 80/sup 0/C to 135/sup 0/C)

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, D J; Gonska, H; Karcher, W

    1984-01-01

    The closed cup flashpoints of five pure hydrocarbon materials (iso-octane, toluene, n-dodecane, n-tetradecane and n-hexadecane) have been determined by equilibrium methods in an interlaboratory exercise, involving twelve laboratories of the European Community member countries and one laboratory of the Commission of the European Communities. The methods used were based on IP303/74 (or ASTM D3278-73; Rapid Tester) and IP304/74 (Abel, Abel-Pensky, Pensky-Martens Cups) with extension to allow equilibrium conditions to be maintained outside the ranges of these methods. For each hydrocarbon material, the numbers of individual measurements accepted have been between 81 and 92. As a result, the closed cup flashpoints of these materials by an equilibrium method are certified at the following temperatures: CRM No. Hydrocarbon Equilibrium closed cup flashpoint 83 iso-octane -9.5 +- 0.5/sup 0/C 84 toluene +6.0 +- 0.5/sup 0/C 85 n-dodecane +81.0 +- 1.0/sup 0/C 86 n-tetradecane +108.0 +- 1.0/sup 0/C 87 n-hexadecane +133.5 +- 1.0/sup 0/C. This report describes the experimental details of the interlaboratory measurements and the certification procedure. The procedure required extensions to be made to methods IP303/74 and IP304/74 which are given in detail and recommendations are made for the improvement of these methods over the temperature range covered by the flashpoint reference materials.

  14. Purifying hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Demoulins, H D; Garner, F H

    1923-02-07

    Hydrocarbon distillates, including natural gases and vapors produced by cracking hydrocarbon oils, are desulfurized etc. by treating the vapor with an aqueous alkaline solution of an oxidizing agent. The hydrocarbons may be previously purified by sulfuric acid. In examples aqueous solutions of sodium or calcium hydrochlorite containing 1.5 to 5.0 grams per liter of available chlorine and sufficient alkali to give an excess of 0.1 percent in the spent reagent are preheated to the temperature of the vapor, and either sprayed or atomized into the vapors near the outlet of the dephlegmator or fractionating tower, or passed in countercurrent to the vapors through one or a series of scrubbers.

  15. Maturity Models

    DEFF Research Database (Denmark)

    Lasrado, Lester Allan; Vatrapu, Ravi

    2016-01-01

    Recent advancements in set theory and readily available software have enabled social science researchers to bridge the variable-centered quantitative and case-based qualitative methodological paradigms in order to analyze multi-dimensional associations beyond the linearity assumptions, aggregate...... effects, unicausal reduction, and case specificity. Based on the developments in set theoretical thinking in social sciences and employing methods like Qualitative Comparative Analysis (QCA), Necessary Condition Analysis (NCA), and set visualization techniques, in this position paper, we propose...... and demonstrate a new approach to maturity models in the domain of Information Systems. This position paper describes the set-theoretical approach to maturity models, presents current results and outlines future research work....

  16. Purifying hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Dunstan, A E

    1918-06-03

    Ligroin, kerosene, and other distillates from petroleum and shale oil, are purified by treatment with a solution of a hypochlorite containing an excess of alkali. The hydrocarbon may be poured into brine, the mixture stirred, and an electric current passed through. Heat may be applied.

  17. Correlation between dental maturity and cervical vertebral maturity.

    Science.gov (United States)

    Chen, Jianwei; Hu, Haikun; Guo, Jing; Liu, Zeping; Liu, Renkai; Li, Fan; Zou, Shujuan

    2010-12-01

    The aim of this study was to investigate the association between dental and skeletal maturity. Digital panoramic radiographs and lateral skull cephalograms of 302 patients (134 boys and 168 girls, ranging from 8 to 16 years of age) were examined. Dental maturity was assessed by calcification stages of the mandibular canines, first and second premolars, and second molars, whereas skeletal maturity was estimated by the cervical vertebral maturation (CVM) stages. The Spearman rank-order correlation coefficient was used to measure the association between CVM stage and dental calcification stage of individual teeth. The mean chronologic age of girls was significantly lower than that of boys in each CVM stage. The Spearman rank-order correlation coefficients between dental maturity and cervical vertebral maturity ranged from 0.391 to 0.582 for girls and from 0.464 to 0.496 for boys (P cervical vertebral maturation stage. The development of the mandibular second molar in females and that of the mandibular canine in males had the strongest correlations with cervical vertebral maturity. Therefore, it is practical to consider the relationship between dental and skeletal maturity when planning orthodontic treatment. Copyright © 2010 Mosby, Inc. All rights reserved.

  18. Effect of Thermal Maturation on n-alkanes and Kerogen in Preserved Organic Matter: Implications for Paleoenvironment Biomarkers

    Science.gov (United States)

    Craven, O. D.; Longbottom, T. L.; Hockaday, W. C.; Blackaby, E.

    2017-12-01

    Understanding the effects of maturity on biomarkers is vital in assessing biomarker reliability in mature sediments. It is well known for n-alkanes that increased maturity shortens chain lengths and decreases the odd over even preference however, the amount of change in these variables has not been determined for different maturities and types of preserved organic matter. For this reason, it is difficult to judge the trustworthiness of even lightly matured samples for paleoenvironment reconstruction. Another complication is the difficulty of accurately determining maturity as many maturity indicators are error-prone or not appropriate at low maturities. Using hydrous pyrolysis, we artificially matured black shale samples with type I (lacustrine) and type II (marine) kerogen to measure changes in n-alkane length and odd over even preference. Whole rock samples underwent hydrous pyrolysis for 72 hours, at 250 °C, 300 °C, 325 °C, 350 °C, and 375 °C to cover a wide maturity range. From the immature and artificially matured samples, the bitumen was extracted and the saturate fraction was separated using column chromatography. The saturate fraction was analyzed for n-alkanes using gas chromatography-mass spectroscopy. Kerogen structural changes were also measured using solid-state 13C NMR to relate changes in n-alkane biomarkers to changes in kerogen structure. Results show that for type I bitumen the n-alkanes did not change at low maturities considered premature in terms of oil generation (<325 °C). The NMR spectra of the type I kerogen support the lack of change, at low maturities no changes in the aliphatic portion (Fal) were observed, however, after 325 °C Fal decreased with increasing maturity. The loss of Fal indicates kerogen contributing hydrocarbons to bitumen that cause changes in n-alkane measurements. The type II kerogen's Fal also decreased with increasing maturity, but unlike the type I kerogen Fal loss started at low maturities. The differences

  19. Hydrocarbon-degrading sulfate-reducing bacteria in marine hydrocarbon seep sediments

    OpenAIRE

    Kleindienst, Sara

    2012-01-01

    Microorganisms are key players in our biosphere because of their ability to degrade various organic compounds including a wide range of hydrocarbons. At marine hydrocarbon seeps, more than 90% of sulfate reduction (SR) is potentially coupled to non-methane hydrocarbon oxidation. Several hydrocarbon-degrading sulfate-reducing bacteria (SRB) were enriched or isolated from marine sediments. However, in situ active SRB remained largely unknown. In the present thesis, the global distribution and a...

  20. Beyond maturity

    International Nuclear Information System (INIS)

    Tessmer, W.B.

    1990-01-01

    The Nuclear Power Plant Simulator Industry has undergone to decades of evolution in experience, technology and business practices. Link-Miles Simulation Corporation (LMSC) has been contracted to build 68 Full Scope Nuclear Simulators during the 1970's and 1980's. Traditional approaches to design, development and testing have been used to satisfy specifications for initial customer requirements. However, the Industry has matured. All U.S. Nuclear Utilities own, or have under contract, at least one simulator. Other industrial nations have centralized training facilities to satisfy the simulator training needs. The customer of the future is knowledgeable and experienced in the development and service of nuclear simulators. The role of the simulator vendor is changing in order to alter the traditional approach for development. Covenants between the vendors and their customers solidify new complementary roles. This paper presents examples of current simulator project development with recommendations for future endeavors

  1. Cracking hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Forwood, G F; Lane, M; Taplay, J G

    1921-10-07

    In cracking and hydrogenating hydrocarbon oils by passing their vapors together with steam over heated carbon derived from shale, wood, peat or other vegetable or animal matter, the gases from the condenser are freed from sulfuretted hydrogen, and preferably also from carbon dioxide, and passed together with oil vapors and steam through the retort. Carbon dioxide may be removed by passage through slaked lime, and sulfuretted hydrogen by means of hydrated oxide of iron. Vapors from high-boiling oils and those from low-boiling oils are passed alternately through the retort, so that carbon deposited from the high-boiling oils is used up during treatment of low-boiling oils.

  2. Distilling hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Bataafsche, N V; de Brey, J H.C.

    1918-10-30

    Hydrocarbons containing a very volatile constituent and less volatile constituents, such as casing-head gases, still gases from the distillation of crude petroleum and bituminous shale are separated into their constituents by rectification under pressure; a pressure of 20 atmospheres and limiting temperatures of 150/sup 0/C and 40/sup 0/C are mentioned as suitable. The mixture may be subjected to a preliminary treatment consisting in heating to a temperature below the maximum rectification temperature at a pressure greater than that proposed to be used in the rectification.

  3. Palynofacies characterization for hydrocarbon source rock ...

    Indian Academy of Sciences (India)

    source rock potential of the Subathu Formation in the area. Petroleum geologists are well aware of the fact that the dispersed organic matter derived either from marine or non-marine sediments on reach- ing its maturation level over extended period of time contributes as source material for the produc- tion of hydrocarbons.

  4. Hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    Foorwood, G F; Taplay, J G

    1916-12-12

    Hydrocarbon oils are hydrogenated, cracked, or treated for the removal of sulfur by bringing their vapors mixed with steam at temperatures between 450 and 600/sup 0/C into contact with a form of carbon that is capable of decomposing steam with the production of nascent hydrogen at those temperatures. The forms of carbon used include lamp-black, soot, charcoals derived from wood, cellulose, and lignite, and carbons obtained by carbonizing oil residues and other organic bodies at temperatures below 600/sup 0/C. The process is applied to the treatment of coal oil, shale oil, petroleum, and lignite oil. In examples, kerosene is cracked at 570/sup 0/C, cracked spirit is hydrogenated at 500/sup 0/C, and shale spirit is desulfurized at 530/sup 0/C. The products are led to a condenser and thence to a scrubber, where they are washed with creosote oil. After desulfurization, the products are washed with dilute caustic soda to remove sulfurretted hydrogen.

  5. Biogeochemistry of Halogenated Hydrocarbons

    Science.gov (United States)

    Adriaens, P.; Gruden, C.; McCormick, M. L.

    2003-12-01

    Halogenated hydrocarbons originate from both natural and industrial sources. Whereas direct anthropogenic emissions to the atmosphere and biosphere are often easy to assess, particularly when they are tied to major industrial activities, the attribution of emissions to other human activities (e.g., biomass burning), diffuse sources (e.g., atmospheric discharge, run off), and natural production (e.g., soils, fungi, algae, microorganisms) are difficult to quantify. The widespread occurrence of both alkyl and aryl halides in groundwater, surface water, soils, and various trophic food chains, even those not affected by known point sources, suggests a substantial biogeochemical cycling of these compounds (Wania and Mackay, 1996; Adriaens et al., 1999; Gruden et al., 2003). The transport and reactive fate mechanisms controlling their reactivity are compounded by the differences in sources of alkyl-, aryl-, and complex organic halides, and the largely unknown impact of biogenic processes, such as enzymatically mediated halogenation of organic matter, fungal production of halogenated hydrocarbons, and microbial or abiotic transformation reactions (e.g., Asplund and Grimvall, 1991; Gribble, 1996; Watling and Harper, 1998; Oberg, 2002). The largest source may be the natural halogenation processes in the terrestrial environment, as the quantities detected often exceed the amount that can be explained by human activities in the surrounding areas ( Oberg, 1998). Since biogeochemical processes result in the distribution of a wide range of halogenated hydrocarbon profiles, altered chemical structures, and isomer distributions in natural systems, source apportionment (or environmental forensics) can often only be resolved using multivariate statistical methods (e.g., Goovaerts, 1998; Barabas et al., 2003; Murphy and Morrison, 2002).This chapter will describe the widespread occurrence of halogenated hydrocarbons, interpret their distribution and biogeochemical cycling in light of

  6. Identification and Characterisation of Major Hydrocarbons in ...

    African Journals Online (AJOL)

    Identification and Characterisation of Major Hydrocarbons in Thermally Degraded Low Density Polyethylene Films. ... There were alkanes, alkenes, halogenated alkanes, and very few aromatics in the liquid product and, the hydrocarbons were observed to range between C10 - C27. The FTIR and GC-MS results show the ...

  7. Detection of hydrocarbons in irradiated foods

    International Nuclear Information System (INIS)

    Miyahara, Makoto; Maitani, Tamio; Saito, Akiko; Kamimura, Tomomi; Nagasawa, Taeko; Kobayashi, Yasuo; Ito, Hitoshi

    2003-01-01

    The hydrocarbon method for the detection of irradiated foods is now recognized as the international technique. This method is based on radiolysis of fatty acids in food to give hydrocarbons. In order to expand this technique's application, ten foods (butter, cheese, chicken, pork, beef, tuna, dry shrimp, avocado, papaya, and mango) were irradiated in the range from 0.5 to 10 kGy and the hydrocarbons in them were detected. Recoveries of the hydrocarbons from most foods were acceptable (38-128%). Some hydrocarbons were found in non-irradiated foods, particularly, in butter, cheese, tuna, and shrimp. Seven irradiated foods, butter, cheese, chicken, beef, pork, tuna, dry shrimp, and avocado were detectable at their practical doses by measuring the appropriate marker hydrocarbons. In most case, marker hydrocarbon will be 1,7-hexadecadiene. However, the marker hydrocarbons produced only in irradiated foods varied from food to food; therefore, it is necessary to check a specific irradiated food for marker hydrocarbons. On the other hand, two irradiated foods (papaya and mango which were irradiated at their practical doses) were difficult to distinguish from non-irradiated foods using this method. (author)

  8. Detection of hydrocarbons in irradiated foods

    Energy Technology Data Exchange (ETDEWEB)

    Miyahara, Makoto; Maitani, Tamio [National Inst. of Health Sciences, Tokyo (Japan); Saito, Akiko; Kamimura, Tomomi; Nagasawa, Taeko [Kitasato Univ., Sagamihara, Kanagawa (Japan). School of Allied Health Sciences; Kobayashi, Yasuo; Ito, Hitoshi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Establishment

    2003-06-01

    The hydrocarbon method for the detection of irradiated foods is now recognized as the international technique. This method is based on radiolysis of fatty acids in food to give hydrocarbons. In order to expand this technique's application, ten foods (butter, cheese, chicken, pork, beef, tuna, dry shrimp, avocado, papaya, and mango) were irradiated in the range from 0.5 to 10 kGy and the hydrocarbons in them were detected. Recoveries of the hydrocarbons from most foods were acceptable (38-128%). Some hydrocarbons were found in non-irradiated foods, particularly, in butter, cheese, tuna, and shrimp. Seven irradiated foods, butter, cheese, chicken, beef, pork, tuna, dry shrimp, and avocado were detectable at their practical doses by measuring the appropriate marker hydrocarbons. In most case, marker hydrocarbon will be 1,7-hexadecadiene. However, the marker hydrocarbons produced only in irradiated foods varied from food to food; therefore, it is necessary to check a specific irradiated food for marker hydrocarbons. On the other hand, two irradiated foods (papaya and mango which were irradiated at their practical doses) were difficult to distinguish from non-irradiated foods using this method. (author)

  9. Evaluation of hydrocarbon potential

    International Nuclear Information System (INIS)

    Cashman, P.H.; Trexler, J.H. Jr.

    1992-01-01

    Task 8 is responsible for assessing the hydrocarbon potential of the Yucca Mountain vincinity. Our main focus is source rock stratigraphy in the NTS area in southern Nevada. (In addition, Trexler continues to work on a parallel study of source rock stratigraphy in the oil-producing region of east central Nevada, but this work is not funded by Task 8.) As a supplement to the stratigraphic studies, we are studying the geometry and kinematics of deformation at NTS, particularly as these pertain to reconstructing Paleozoic stratigraphy and to predicting the nature of the Late Paleozoic rocks under Yucca Mountain. Our stratigraphic studies continue to support the interpretation that rocks mapped as the open-quotes Eleana Formationclose quotes are in fact parts of two different Mississippian units. We have made significant progress in determining the basin histories of both units. These place important constraints on regional paleogeographic and tectonic reconstructions. In addition to continued work on the Eleana, we plan to look at the overlying Tippipah Limestone. Preliminary TOC and maturation data indicate that this may be another potential source rock

  10. Conversion of hydrocarbon oils into motor fuels

    Energy Technology Data Exchange (ETDEWEB)

    1937-11-09

    The abstract describes a process for producing lower boiling hydrocarbon motor fuels with a starting material of wide boiling range composed primarily of hydrocarbon oils boiling substantially above the boiling range of the desired product. Separate catalytic and pyrolytic conversion zones are simultaneously maintained in an interdependent relationship. Higher boiling constituents are separated from residual constituents by fractionation while desirable reaction conditions are maintained. All or at least a portion of the products from the catalytic and pyrolytic conversion zones are blended to yield the desired lower boiling hydrocarbons or motor fuels.

  11. Converting high boiling hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Terrisse, H; DuFour, L

    1929-02-12

    A process is given for converting high boiling hydrocarbons into low boiling hydrocarbons, characterized in that the high boiling hydrocarbons are heated to 200 to 500/sup 0/C in the presence of ferrous chloride and of such gases as hydrogen, water gas, and the like gases under a pressure of from 5 to 40 kilograms per square centimeter. The desulfurization of the hydrocarbons occurs simultaneously.

  12. Maturity and maturity models in lean construction

    Directory of Open Access Journals (Sweden)

    Claus Nesensohn

    2014-03-01

    Full Text Available In recent years there has been an increasing interest in maturity models in management-related disciplines; which reflects a growing recognition that becoming more mature and having a model to guide the route to maturity can help organisations in managing major transformational change. Lean Construction (LC is an increasingly important improvement approach that organisations seek to embed. This study explores how to apply the maturity models to LC. Hence the attitudes, opinions and experiences of key industry informants with high levels of knowledge of LC were investigated. To achieve this, a review of maturity models was conducted, and data for the analysis was collected through a sequential process involving three methods. First a group interview with seven key informants. Second a follow up discussion with the same individuals to investigate some of the issues raised in more depth. Third an online discussion held via LinkedIn in which members shared their views on some of the results. Overall, we found that there is a lack of common understanding as to what maturity means in LC, though there is general agreement that the concept of maturity is a suitable one to reflect the path of evolution for LC within organisations.

  13. Slab replacement maturity guidelines.

    Science.gov (United States)

    2014-04-01

    This study investigated the use of maturity method to determine early age strength of concrete in slab : replacement application. Specific objectives were (1) to evaluate effects of various factors on the compressive : maturity-strength relationship ...

  14. Characterization of hydrocarbon utilizing fungi from hydrocarbon ...

    African Journals Online (AJOL)

    Prof. Ogunji

    isolated fungi could be useful in the bioremediation of hydrocarbon polluted sites. Keywords: ... Technologies such as mechanical force, burying, evaporation, dispersant application, and ..... The effects of drilling fluids on marine bacteria from a.

  15. Hydrocarbon potential of a new Jurassic play, central Tunisia

    International Nuclear Information System (INIS)

    Beall, A.O.; Law, C.W.

    1996-01-01

    A largely unrecognized Jurassic Sag Basin has been identified in central Tunisia, proximal to the Permo-Carboniferous flexure delineating the northern boundary of the Saharan platform of north Africa. The northwestern margin of the Sag is delineated by an extensive region of salt-cored anticlines and localized salt diapirs extending north and west. Due to lack of deep drilling, delineation of the Sag is largely based on regional gravity data. Subsidence of the Jurassic Sag Basin is characterized by rapid expansion of Jurassic sediments from 400 m. of tidal flat and shelf carbonate at the western outcrop to over 2000 meters of tidal flat and basinal carbonate and shale within the basin center, a five-fold expansion. Rapid loading of the basin continued into Lower Cretaceous time, marked by lateral flowage of Triassic salt into pronounced structural trends. Published source rock data and interpreted subsurface well data provided the basis for GENEX 1-D hydrocarbon generation and expulsion modeling of the Sag. Middle Jurassic black source shales typically contain Type II and Type III kerogens with T.O.C.'s ranging up to 4 percent. Modeling results indicate that middle Jurassic shales are presently mature for liquid generation within portions of the Sag, with maximum generation taking place during the Tertiary. Potential hydrocarbon generation yields, based on 60 meters of mature source shale, are 20,000 BOE/acre for gas and 75,000 BOE/acre for liquids. Prospects within the region could contain an estimated potential reserve of several T.C.F. or over 1 billion barrels of oil

  16. Hydrocarbons and air pollution

    International Nuclear Information System (INIS)

    Herz, O.

    1992-01-01

    This paper shows the influence of hydrocarbons vapors, emitted by transports or by volatile solvents using, on air pollution. Hydrocarbons are the principal precursors of photochemical pollution. After a brief introduction on atmospheric chemistry and photochemical reactions, the author describes the french prevention program against hydrocarbons emissions. In the last chapter, informations on international or european community programs for photochemical pollution study are given. 5 figs., 10 tabs

  17. Production of hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Day, D T; Day, R E

    1920-04-27

    A process is disclosed of converting hydro-carbon oils having high boiling points to hydro-carbon oils having low boiling points, which process comprises adding the oil to be treated to a mass of hydro-carbon oil bearing shale, passing the shale with the oil through a conveyor retort and subjecting the material while in the retort to a heat treatment involving a temperature of at least 500/sup 0/F.

  18. Plasma devices for hydrocarbon reformation

    KAUST Repository

    Cha, Min

    2017-01-01

    Plasma devices for hydrocarbon reformation are provided. Methods of using the devices for hydrocarbon reformation are also provided. The devices can include a liquid container to receive a hydrocarbon source, and a plasma torch configured

  19. Hydrocarbon potential of Ordovician and Silurian rocks. Siljan Region (Sweden)

    Energy Technology Data Exchange (ETDEWEB)

    Berner, U. [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Hannover (Germany); Lehnert, O. [Erlangen-Nuernberg Univ., Erlangen (Germany); Meinhold, G. [Goettingen Univ. (Germany)

    2013-08-01

    Hydrocarbon exploration in the vicinity of Europe's largest impact structure (Siljan, Central Sweden) focused for years on abiogenic concepts and largely neglected state of the art knowledge on hydrocarbon generation via thermal decomposition of organic matter. In our study we use sedimentary rocks obtained from three drill sites (Mora001, Stumsnaes 1 and Solberga 1) within the ring structure around the central uplift to investigate the hydrocarbon potential of Ordovician and Silurian strata of the region and also for comparison with the shale oil and gas potential of age equivalent rocks of the Baltic Sea. Elemental analyses provided information on concentrations of carbonate and organic carbon, total sulfur as well as on the composition of major and minor elements of the sediments. The data has been used to evaluate the depositional environment and possible diagenetic alterations of the organic matter. RockEval pyrolysis and solvent hydrocarbon extraction gave insight into the hydrocarbon generation potential and the type and thermal maturity of the sediments. From the geochemistry data of the studied wells it is obvious that changes of depositional environments (lacustrine - marine) have occurred during Ordovician and Silurian times. Although, the quality of the organic matter has been influenced in marine and brackish environments through sulfate reduction, we observe for a number of marine and lacustrine sediments a good to excellent preservation of the biological precursors which qualify the sediments as hydrocarbon source rocks (Type II kerogens). Lacustrine source rocks show a higher remaining hydrocarbon potential (up to {proportional_to}550 mg HC per g C{sub org}) than those of marine or brackish environments. Our investigations indicate that the thermal maturity of organic matter of the drill sites has reached the initial stage of oil generation. However, at Mora001 some of the sediments were stained with oil indicating that hydrocarbons have

  20. Plasma devices for hydrocarbon reformation

    KAUST Repository

    Cha, Min Suk

    2017-02-16

    Plasma devices for hydrocarbon reformation are provided. Methods of using the devices for hydrocarbon reformation are also provided. The devices can include a liquid container to receive a hydrocarbon source, and a plasma torch configured to be submerged in the liquid. The plasma plume from the plasma torch can cause reformation of the hydrocarbon. The device can use a variety of plasma torches that can be arranged in a variety of positions in the liquid container. The devices can be used for the reformation of gaseous hydrocarbons and/or liquid hydrocarbons. The reformation can produce methane, lower hydrocarbons, higher hydrocarbons, hydrogen gas, water, carbon dioxide, carbon monoxide, or a combination thereof.

  1. Tectonic control in source rock maturation and oil migration in Trinidad

    Energy Technology Data Exchange (ETDEWEB)

    Persad, K.M.; Talukdar, S.C.; Dow, W.G. (DGSI, The Woodlands, TX (United States))

    1993-02-01

    Oil accumulation in Trinidad were sourced by the Upper Cretaceous calcareous shales deposited along the Cretaceous passive margin of northern South America. Maturation of these source rocks, oil generation, migration and re-migration occurred in a foreland basin setting that resulted from interaction between Caribbean and South American plates during Late Oligocene to recent times. During Middle Miocene-Recent times, the foreland basin experienced strong compressional events, which controlled generation, migration, and accumulation of oil in Trinidad. A series of mature source rock kitchens formed in Late Miocene-Recent times in the Southern and Colombus Basins to the east-southeast of the Central Range Thrust. This thrust and associated fratured developed around 12 m.y.b.p. and served as vertical migration paths for the oil generated in Late Miocene time. This oil migrated into submarine fans deposited in the foreland basin axis and older reservoirs deformed into structural traps. Further generation and migration of oil, and re-migration of earlier oil took place during Pliocene-Holocene times, when later thrusting and wrench faulting served as vertical migration paths. Extremely high sedimentation rates in Pliocene-Pleistocene time, concurrent with active faulting, was responsible for very rapid generation of oil and gas. Vertically migrating gas often mixed with earlier migrated oil in overlying reservoirs. This caused depletion of oil in light hydrocarbons with accompanied fractionation among hydrocarbon types resulting in heavier oil in lower reservoirs, enrichment of light hydrocarbons and accumulation of gas-condensates in upper reservoirs. This process led to an oil-gravity stratification within about 10,000 ft of section.

  2. Maturity grids as tools for change management

    DEFF Research Database (Denmark)

    Maier, Anja; Moultrie, James; Clarkson, P John

    2011-01-01

    A maturity grid is a change management tool. Levels of maturity are assigned against aspects of an area under study, thus creating a grid. Text descriptions at the resulting intersections describe the typical behaviour exhibited by a firm for each area under study and from the basis...... for the assessment scale. It is a flexible assessment technique that is used by practitioners in industry, consultants and researchers in academia for diagnostic, reflective and improvement purposes. A large number of maturity grids have been proposed to assess a range of capabilities including quality management...

  3. Catalytic pyrolysis of hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Vail' eva, N A; Buyanov, R A

    1979-01-01

    Catalytic pyrolysis of petroleum fractions (undecane) was performed with the object of clarifying such questions as the mechanism of action of the catalyst, the concepts of activity and selectivity of the catalyst, the role of transport processes, the temperature ranges and limitations of the catalytic process, the effect of the catalyst on secondary processes, and others. Catalysts such as quartz, MgO, Al/sub 2/O/sub 3/, were used. Analysis of the experimental findings and the fact that the distribution of products is independent of the nature of the surface, demonstrate that the pyrolysis of hydrocarbons in the presence of catalysts is based on the heterogeneous-homogeneous radical-chain mechanism of action, and that the role of the catalysts reduces to increasing the concentration of free radicals. The concept of selectivity cannot be applied to catalysts here, since they do not affect the mechanism of the unfolding of the process of pyrolysis and their role consists solely in initiating the process. In catalytic pyrolysis the concepts of kinetic and diffusive domains of unfolding of the catalytic reaction do not apply, and only the outer surface of the catalyst is engaged, whereas the inner surface merely promotes deletorious secondary processes reducing the selectivity of the process and the activity of the catalyst. 6 references, 2 figures.

  4. Maturity of the PWR

    International Nuclear Information System (INIS)

    Bacher, P.; Rapin, M.; Aboudarham, L.; Bitsch, D.

    1983-03-01

    Figures illustrating the predominant position of the PWR system are presented. The question is whether on the basis of these figures the PWR can be considered to have reached maturity. The following analysis, based on the French program experience, is an attempt to pinpoint those areas in which industrial maturity of the PWR has been attained, and in which areas a certain evolution can still be expected to take place

  5. Assessment of skeletal maturation using mandibular second molar maturation stages.

    Science.gov (United States)

    Goyal, S; Goyal, S; Gugnani, N

    2014-01-01

    To investigate the relationship between cervical vertebrae maturation and mandibular second molar calcification stages. The study was designed as a retrospective, descriptive and crosssectional research project. Pre-treatment lateral cephalograms and panoramic radiographs of 99 males and 110 females in the age range of 7 to 18 years 7 months were evaluated with Demirjian Index (DI) and cervical vertebrae maturation indicators (CVMI) of Hassel and Farman. A null hypothesis was proposed that there is no relation between CVMI and DI. A highly significant association (Pearson's contingency coefficient 0.713 for males and 0.863 for females) was found between DI and CVMI. In males, the DI stage E corresponded to stage 2 of CVMI (pre-peak of pubertal growth spurt) and DI stages F and G corresponded to stages 3 and 4 of CVMI (peak of pubertal growth spurt). DI stage H was associated with stages 5 and 6 of CVMI (end of pubertal growth spurt). In females, the DI stages C, D corresponded to CVMI stages 1, 2; DI stages E, F with CVMI stages 3, 4; DI stages G, H with CVMI stages 5, 6. Mandibular second molar calcification stages can be used as indicators for assessment of skeletal maturity.

  6. Thraustochytrid protists degrade hydrocarbons

    Digital Repository Service at National Institute of Oceanography (India)

    Raikar, M.T.; Raghukumar, S.; Vani, V.; David, J.J.; Chandramohan, D.

    isolation tubes with crude oil. Three isolates tested showed positive hydrophobicity of cell walls as judged by the Microbial Adhesion to Hydrocarbons (MATH) assay. Addition of Bombay High crude oil to nutrient broth slightly enhanced growth of the protists...

  7. Process for making unsaturated hydrocarbons using microchannel process technology

    Science.gov (United States)

    Tonkovich, Anna Lee [Dublin, OH; Yuschak, Thomas [Lewis Center, OH; LaPlante, Timothy J [Columbus, OH; Rankin, Scott [Columbus, OH; Perry, Steven T [Galloway, OH; Fitzgerald, Sean Patrick [Columbus, OH; Simmons, Wayne W [Dublin, OH; Mazanec, Terry Daymo, Eric

    2011-04-12

    The disclosed invention relates to a process for converting a feed composition comprising one or more hydrocarbons to a product comprising one or more unsaturated hydrocarbons, the process comprising: flowing the feed composition and steam in contact with each other in a microchannel reactor at a temperature in the range from about 200.degree. C. to about 1200.degree. C. to convert the feed composition to the product, the process being characterized by the absence of catalyst for converting the one or more hydrocarbons to one or more unsaturated hydrocarbons. Hydrogen and/or oxygen may be combined with the feed composition and steam.

  8. Purifying hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    Rostin, H

    1938-08-11

    A process is described for continuously purifying hydrocarbon oils consisting in conducting the vapors of the same at a temperature of 300 to 400/sup 0/C over the oelitic ore minette together with reducing gases in presence of steam the proportion of the reducing gases and steam being such that the sulfur of the hydrocarbons escapes from the reaction chamber in the form of sulfuretted hydrogen without permanent sulfide of iron being formed.

  9. Process for refining hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Risenfeld, E H

    1924-11-26

    A process is disclosed for the refining of hydrocarbons or other mixtures through treatment in vapor form with metal catalysts, characterized by such metals being used as catalysts, which are obtained by reduction of the oxide of minerals containing the iron group, and by the vapors of the hydrocarbons, in the presence of the water vapor, being led over these catalysts at temperatures from 200 to 300/sup 0/C.

  10. Algal Lipid Extraction and Upgrading to Hydrocarbons Technology Pathway

    Energy Technology Data Exchange (ETDEWEB)

    Davis, R.; Biddy, M.; Jones, S.

    2013-03-01

    This technology pathway case investigates the cultivation of algal biomass followed by further lipid extraction and upgrading to hydrocarbon biofuels. Technical barriers and key research needs have been assessed in order for the algal lipid extraction and upgrading pathway to be competitive with petroleum-derived gasoline-, diesel-, and jet-range hydrocarbon blendstocks.

  11. Application of fission track analysis to hydrocarbon exploration

    International Nuclear Information System (INIS)

    Duddy, I.R.; Green, P.F.; Gleadow, A.J.W.; Marshallsea, S.; Tingate, P.; Laslett, G.M.; Hegarty, K.A.; Lovering, J.F.

    1985-01-01

    The temperature range over which fission tracks in apatite show observable annealing effects coincides with that responsible for the maximum generation of liquid hydrocarbons. Work is currently in progress in a number of Australian and overseas sedimentary basins, applying Apatite Fission Track Analysis (AFTA) to investigate the thermal evolution of these hydrocarbon prospective regions

  12. Biological Conversion of Sugars to Hydrocarbons Technology Pathway

    Energy Technology Data Exchange (ETDEWEB)

    Davis, R.; Biddy, M.; Tan, E.; Tao, L.; Jones, S.

    2013-03-01

    This technology pathway case investigates the biological conversion of biomass-derived sugars to hydrocarbon biofuels, utilizing data from recent literature references and information consistent with recent pilot-scale demonstrations at NREL. Technical barriers and key research needs have been identified that should be pursued for the pathway to become competitive with petroleum-derived gasoline-, diesel-, and jet-range hydrocarbon blendstocks.

  13. Catalytic cracking of hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    1940-09-12

    A process is described for the vapor phase catalytic cracking of hydrocarbon oils boiling substantially in the gas oil range. The reaction takes place in the presence of a solid catalyst between 700 to 900/sup 0/F under pressure between atmospheric and 400 psi. A gas containing between 20 and 90 mol % of free hydrogen is used. The reaction is allowed to proceed until consumption of the free begins. The reaction is discontinued at that point and the catalyst is regenerated for further use.

  14. Bioremediation of petroleum hydrocarbons in soil environments

    International Nuclear Information System (INIS)

    Rowell, M.J.; Ashworth, J.; Qureshi, A.A.

    1992-12-01

    The bioremediation of petroleum hydrocarbons in soil environments was reviewed via a literature survey and discussions with workers in relevant disciplines. The impacts of hydrocarbons on soil are discussed along with a range of methods available to assist in their decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, sludges, asphalts and bitumens, drilling mud residues, creosote tars, and some pesticides. The degradability of hydrocarbons largely depends upon their aqueous solubility and their adsorption on soil surfaces and, therefore, is related to their molecular structures. The ease of decomposition decreases with increasing complexity of structure, in the order aliphatics > aromatics > heterocyclics and asphaltenes (most recalcitrant). Most soils contain an adequate population of microorganisms and hence bioaugmentation may only be needed in special circumstances. Decomposition is fastest in soils where the hydrocarbon loading rate, aeration, nutrition, moisture, and pH are all optimized. At spill sites there is little control over the application rate, although containment measures can assist in either limiting contamination or distributing it more evenly. The enhancement of bioremediation is discussed in light of all these factors. Other techniques such as enhanced aeration, hydrocarbon decomposition by anaerobic processes, surfactants, and burning are also discussed. 211 refs., 11 figs., 10 tabs

  15. Bioremediation of petroleum hydrocarbons in soil environments

    Energy Technology Data Exchange (ETDEWEB)

    Rowell, M J; Ashworth, J; Qureshi, A A

    1992-12-01

    The bioremediation of petroleum hydrocarbons in soil environments was reviewed via a literature survey and discussions with workers in relevant disciplines. The impacts of hydrocarbons on soil are discussed along with a range of methods available to assist in their decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, sludges, asphalts and bitumens, drilling mud residues, creosote tars, and some pesticides. The degradability of hydrocarbons largely depends upon their aqueous solubility and their adsorption on soil surfaces and, therefore, is related to their molecular structures. The ease of decomposition decreases with increasing complexity of structure, in the order aliphatics > aromatics > heterocyclics and asphaltenes (most recalcitrant). Most soils contain an adequate population of microorganisms and hence bioaugmentation may only be needed in special circumstances. Decomposition is fastest in soils where the hydrocarbon loading rate, aeration, nutrition, moisture, and pH are all optimized. At spill sites there is little control over the application rate, although containment measures can assist in either limiting contamination or distributing it more evenly. The enhancement of bioremediation is discussed in light of all these factors. Other techniques such as enhanced aeration, hydrocarbon decomposition by anaerobic processes, surfactants, and burning are also discussed. 211 refs., 11 figs., 10 tabs.

  16. Polycyclic Aromatic Hydrocarbons

    Science.gov (United States)

    Salama, Farid

    2010-01-01

    Carbonaceous materials play an important role in space. Polycyclic Aromatic Hydrocarbons (PAHs) are a ubiquitous component of the carbonaceous materials. PAHs are the best-known candidates to account for the IR emission bands. They are also thought to be among the carriers of the diffuse interstellar absorption bands (DIBs). PAH ionization states reflect the ionization balance of the medium while PAH size, composition, and structure reflect the energetic and chemical history of the medium. A major challenge is to reproduce in the laboratory the physical conditions that exist in the emission and absorption interstellar zones. The harsh physical conditions of the ISM -low temperature, collisionless, strong UV radiation fields- are simulated in the laboratory by associating a molecular beam with an ionizing discharge to generate a cold plasma expansion. PAH ions and radicals are formed from the neutral precursors in an isolated environment at low temperature and probed with high-sensitivity cavity ringdown spectroscopy in the NUV-NIR range. Carbon nanoparticles are also formed during the short residence time of the precursors in the plasma and are characterized with time-offlight mass spectrometry. These experiments provide unique information on the spectra of large carbonaceous molecules and ions in the gas phase that can now be directly compared to interstellar and circumstellar observations (IR emission bands, DIBs, extinction curve). These findings also hold great potential for understanding the formation process of interstellar carbonaceous grains. We will review recent progress in the experimental and theoretical studies of PAHs, compare the laboratory data with astronomical observations and discuss the global implications.

  17. Dissolved petroleum hydrocarbons in the Andaman Sea

    Digital Repository Service at National Institute of Oceanography (India)

    Topgi, R.S.; Noronha, R.J.; Fondekar, S.P.

    Mean dissolved petroleum hydrocarbons, measured using UV-spectrophotometry, at 0 and 10m were 51 plus or minus 1 and 55 plus or minus 1.2 mu g/litre respectively; range of variation being between 28 and 83 mu g/litre. Very little difference...

  18. Identifying specific interstellar polycyclic aromatic hydrocarbons

    International Nuclear Information System (INIS)

    Mulas, Giacomo; Malloci, Giuliano; Porceddu, Ignazio

    2005-01-01

    Interstellar Polycyclic Aromatic Hydrocarbons (PAHs) have been thought to be ubiquitous for more than twenty years, yet no single species in this class has been identified in the Interstellar Medium (ISM) to date. The unprecedented sensitivity and resolution of present Infrared Space Observatory (ISO) and forthcoming Herschel observations in the far infrared spectral range will offer a unique way out of this embarrassing impasse

  19. Producing light hydrocarbons by destructive hydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Fohlen, J H

    1928-06-20

    A method of obtaining light hydrocarbons from fuels and natural or industrial carbonaceous materials by cracking under pressure from 5 to 200 atmospheres and within a temperature range of 200 to 1,000/sup 0/C, the cracking operation being assisted by the presence of catalysts such as metallic halides, simultaneously, with hydrogenation by means of nascent hydrogen in the reaction chamber.

  20. Occurrence and growth potentials of hydrocarbon degrading ...

    African Journals Online (AJOL)

    The surface of leaf samples from ten tropical plants, Anthocleista, Sarcophrynium, Canna, Colocassia, Musa, Cola, Citrus, Mangifera, Terminalia and Annona were cultured for the estimation of total heterotrophic and hydrocarbon utilizing bacteria. The total heterotrophic bacteria ranged from 0.75 x 107 to 0.98 x 107 ...

  1. Long Maturity Forward Rates

    DEFF Research Database (Denmark)

    Christiansen, Charlotte

    2001-01-01

    The paper aims to improve the knowledge of the empirical properties of the long maturity region of the forward rate curve. Firstly, the theoretical negative correlation between the slope at the long end of the forward rate curve and the term structure variance is recovered empirically and found...... to be statistically significant. Secondly, the expectations hypothesis is analyzed for the long maturity region of the forward rate curve using "forward rate" regressions. The expectations hypothesis is numerically close to being accepted but is statistically rejected. The findings provide mixed support...... for the affine term structure model....

  2. Evaluation of environmental samples containing heavy hydrocarbon components in environmental forensic investigations

    Energy Technology Data Exchange (ETDEWEB)

    Raia, J.C.; Blakley, C.R.; Fuex, A.N.; Villalanti, D.C.; Fahrenthold, P.D. [Triton Anal Corp, Houston, TX (United States)

    2004-03-01

    This article presents a procedure to evaluate and characterize environmental samples containing mixtures of hydrocarbons over a wide boiling range of materials that include fuels and other products used in commerce. The range of the method extends to the higher boiling and heavier molecular weight hydrocarbon products in the range of motor oil, bunker fuel, and heavier residue materials. The procedure uses the analytical laboratory technique of high-temperature simulated distillation along with mathematical regression of the analytical data to estimate the relative contribution of individual products in mixtures of hydrocarbons present in environmental samples. An analytical technique to determine hydrocarbon-type distributions by gas chromatography-mass spectrometry with nitric oxide ionization spectrometry evaluation is also presented. This type of analysis allows complex hydrocarbon mixtures to be classified by their chemical composition, or types of hydrocarbons that include paraffins, cycloparaffins, monoaromatics, and polycyclic aromatic hydrocarbons. Characteristic hydrocarbon patterns for example, in the relative distribution of polycyclic aromatic hydrocarbons are valuable for determining the potential origin of materials present in environmental samples. These methods provide quantitative data for hydrocarbon components in mixtures as a function of boiling range and 'hydrocarbon fingerprints' of the types of materials present. This information is valuable in assessing environmental impacts of hydrocarbons at contaminated sites and establishing the liabilities and cost allocations for responsible parties.

  3. Trace element characterisation of Cretaceous Orange Basin hydrocarbon source rocks

    International Nuclear Information System (INIS)

    Akinlua, A.; Adekola, S.A.; Swakamisa, O.; Fadipe, O.A.; Akinyemi, S.A.

    2010-01-01

    Research highlights: → Vanadium and nickel contents indicate that the rock samples from the Orange Basin have marine organic matter input. → The organic matter of the Orange Basin source rocks were deposited in reducing conditions. → Despite the similarities in the organic matter source input and depositional environment of the samples from the two well, cross plots of Co/Ni versus V/Ni and Mo/Ni versus Co/Ni were able to reveal their subtle differences. → Cluster analysis classified the samples into three groups based on subtle differences in their .thermal maturity. - Abstract: Trace elements in the kerogen fraction of hydrocarbon source rock samples from two wells obtained from the Cretaceous units of the Orange Basin, South Africa were determined using X-ray fluorescence spectrometry, in order to determine their distribution and geochemical significances. The concentrations of the elements (As, Ce, Co, Cu, Fe, Mo, Ni, Pb and V) determined ranged from 0.64 to 47,300 ppm for the samples analysed. The total organic carbon (TOC) values indicate that the samples are organic rich but did not show any trend with the distribution of the trace metals except Ce, Mo and Pb. Dendrogram cluster analysis discriminated the samples into three groups on the basis of their level of thermal maturity. Thermal maturity has a significant effect on the distribution of the trace metals. Cobalt/Ni and V/Ni ratios and cross plots of the absolute values of V and Ni indicate that the samples had significant marine organic matter input. The V and Ni contents and V/(V + Ni) ratio indicate that the organic matter of the source rocks had been deposited in reducing conditions. Despite the similarities in the organic matter source input and depositional environment of the organic matter of the samples from the two well, cross plots of Co/Ni versus V/Ni and Mo/Ni versus Co/Ni were able to reveal subtle differences. Cluster analysis of the samples was also able to reveal the subtle

  4. Process for desulfurizing hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    1937-04-12

    A process is described for the desulfurization of a mixture of hydrocarbons, and in particular hydrocarbons containing less than 7 atoms of carbon and sulfur compounds of the type of sulfur carbonyl, characterized by the fact that the mixture, preferably in the liquid phase, is brought in contact with a solution of caustic alkali, essentially anhydrous or preferably with a solution of alkali hydroxide in an organic hydroxy nonacid solvent, for example, an alcohol, or with an alkaline alcoholate, under conditions suitable to the formation of hydrogen sulfide which produces a hydrocarbon mixture free from sulfur compounds of the sulfur carbonyl type but containing hydrogen sulfide, and that it is treated, following mixing, having beem submitted to the first treatment, by means of aqueous alkaline hydroxide to eliminate the hydrogen sulfide.

  5. Grammar Maturity Model

    NARCIS (Netherlands)

    Zaytsev, V.; Pierantonio, A.; Schätz, B.; Tamzalit, D.

    2014-01-01

    The evolution of a software language (whether modelled by a grammar or a schema or a metamodel) is not limited to development of new versions and dialects. An important dimension of a software language evolution is maturing in the sense of improving the quality of its definition. In this paper, we

  6. Maturing interorganisational information systems

    NARCIS (Netherlands)

    Plomp, M.G.A.|info:eu-repo/dai/nl/313946809

    2012-01-01

    This thesis consists of nine chapters, divided over five parts. PART I is an introduction and the last part contains the conclusions. The remaining, intermediate parts are: PART II: Developing a maturity model for chain digitisation. This part contains two related studies concerning the development

  7. Jealousy and Moral Maturity.

    Science.gov (United States)

    Mathes, Eugene W.; Deuger, Donna J.

    Jealousy may be perceived as either good or bad depending upon the moral maturity of the individual. To investigate this conclusion, a study was conducted testing two hypothesis: a positive relationship exists between conventional moral reasoning (reference to norms and laws) and the endorsement and level of jealousy; and a negative relationship…

  8. Emissions of hydrocarbons from combustion of biofuels

    International Nuclear Information System (INIS)

    Olsson, Mona; Persson, Eva Marie.

    1991-10-01

    Evaluations and measurements of emissions of hydrocarbons from power plants with a capacity exceeding 1 MW using biofuels (wood fuels and peat) have been studied in order to identify and quantify the emissions of incompletely combusted hydrocarbons. The influence of the type of fuel and the combustion technology applied were also studied, using literature references. The report summarizes monitoring results from a number of plants using biofuels. The reported emissions from the different plants can not be compared as they are relatively few and the test results have been obtained under various conditions using different methods of testing and analysis. The methods used are often poorly documented in the studied reports. Few investigations of emissions of hydrocarbons from plants in the range of 1 to 10 MW have been carried out. The plant and the technology used are important factors determining the amount and type of emissions of hydrocarbons. Larger temporary emissions can occur during start up, operational disturbances or when using fuel of inhomogeneous quality. In order to minimize the emissions the combustion process must be efficiently controlled, and a fuel of a hohogeneous quality must be used. The report also summarizes sampling and analysis methods used for monitoring emissions of hydrocarbons. (29 refs., 17 figs.)

  9. Recovery of hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    1941-02-10

    A process is disclosed for recovery of hydrocarbon oils, especially lubricating oils or diesel oils, through pressure hydrogenation of distillation, extraction of hydrogenation products from coal or coaly materials or from oils such as mineral oils or tars in liquid phase by use in a reaction vessel of fixed-bed catalysts, characterized in that as starting material is employed material which has been freed of asphaltic and resinous material by hydrogenation refining, vacuum-steam distillation, treatment with hydrogen-rich hydrocarbons (hydroforming), or sulfuric acid.

  10. Performance estimation of ejector cycles using heavier hydrocarbon refrigerants

    International Nuclear Information System (INIS)

    Kasperski, Jacek; Gil, Bartosz

    2014-01-01

    Computer software basing on theoretical model of Huang et al. with thermodynamic properties of hydrocarbons was prepared. Investigation was focused on nine hydrocarbons: propane, butane, iso-butane, pentane, iso-pentane, hexane, heptane and octane. A series of calculations was carried out for the generator temperature between 70 and 200 °C, with assumed temperatures of evaporation 10 °C and condensation 40 °C. Calculation results show that none of the hydrocarbons enables high efficiency of a cycle in a wide range of temperature. Each hydrocarbon has its own maximal entrainment ratio at its individual temperature of optimum. Temperatures of entrainment ratios optimum increase according to the hydrocarbon heaviness with simultaneous increase of entrainment ratio peak values. Peak values of the COP do not increase according to the hydrocarbons heaviness. The highest COP = 0.32 is achieved for iso-butane at 102 °C and the COP = 0.28 for pentane at 165 °C. Heptane and octane can be ignored. - Highlights: • Advantages of use of higher hydrocarbons as ejector refrigerants were presumed. • Computer software basing on theoretical model of Huang et al. (1999) was prepared. • Optimal temperature range of vapor generation for each hydrocarbon was calculated

  11. Optrode for sensing hydrocarbons

    Science.gov (United States)

    Miller, H.; Milanovich, F.P.; Hirschfeld, T.B.; Miller, F.S.

    1988-09-13

    A two-phase system employing the Fujiwara reaction is provided for the fluorometric detection of halogenated hydrocarbons. A fiber optic is utilized to illuminate a column of pyridine trapped in a capillary tube coaxially attached at one end to the illuminating end of the fiber optic. A strongly alkaline condition necessary for the reaction is maintained by providing a reservoir of alkali in contact with the column of pyridine, the surface of contact being adjacent to the illuminating end of the fiber optic. A semipermeable membrane caps the other end of the capillary tube, the membrane being preferentially permeable to the halogenated hydrocarbon and but preferentially impermeable to water and pyridine. As the halogenated hydrocarbon diffuses through the membrane and into the column of pyridine, fluorescent reaction products are formed. Light propagated by the fiber optic from a light source, excites the fluorescent products. Light from the fluorescence emission is also collected by the same fiber optic and transmitted to a detector. The intensity of the fluorescence gives a measure of the concentration of the halogenated hydrocarbons. 5 figs.

  12. Catalyst for hydrocarbon conversion

    International Nuclear Information System (INIS)

    Duhaut, P.; Miquel, J.

    1975-01-01

    A description is given for a catalyst and process for hydrocarbon conversions, e.g., reforming. The catalyst contains an alumina carrier, platinum, iridium, at least one metal selected from uranium, vanadium, and gallium, and optionally halogen in the form of metal halide of one of the aforesaid components. (U.S.)

  13. A correlative study of dental age and skeletal maturation.

    Science.gov (United States)

    Sachan, Kiran; Sharma, Vijay Prakash; Tandon, Pradeep

    2011-01-01

    Skeletal age had been assessed by comparison between maturation of hand-wrist with stages of cervical vertebrae or canine calcification stages in past and this had been closely related to craniofacial growth. The importance of pubertal growth spurt in various types of orthodontic therapies is already established. Hence, this study was aimed to evaluate the relationship of skeletal maturity by hand-wrist with cervical vertebral maturation indicators and canine calcification stages. The study consisted of randomly selected 90 children from Lucknow population with 45 males (age range 10-13 years) and 45 females (age range 9-12 years). Lateral Cephalogram, hand-wrist x-ray, and periapical x-rays of maxillary and mandibular right canines were taken. Mean, standard deviation was calculated of different groups. Correlation was made among cervical vertebral maturation, hand wrist maturation, and canine calcification stages at various age groups. There was strong correlation between skeletal maturation indicator and cervical vertebral maturation indicator for both male (0.849) and female (0.932), whereas correlation between skeletal maturation indicator and canine calcification was good for both male and female (0.635, 0.891). It was concluded that cervical vertebral maturation indicator and canine calcification stages can also be used for assessing skeletal maturity.

  14. The presence of hydrocarbons in southeast Norway

    DEFF Research Database (Denmark)

    Hanken, Niels Martin; Hansen, Malene Dolberg; Kresten Nielsen, Jesper

    Hydrocarbons, mostly found as solid pyrobitumen, are known from more than 30 localities in southeast Norway. They occur as inclusions in a wide range of "reservoir rocks" spanning from Permo-Carboniferous breccias to veins (vein quartz and calcite veins) in Precambrian granites, gneisses and amph......Hydrocarbons, mostly found as solid pyrobitumen, are known from more than 30 localities in southeast Norway. They occur as inclusions in a wide range of "reservoir rocks" spanning from Permo-Carboniferous breccias to veins (vein quartz and calcite veins) in Precambrian granites, gneisses......, indicating that Alum Shale was the most important source rock. Petrographic investigations combined with stable isotope analyses (d13C and d18O) of the cement containing pyrobitumen indicate two phases of hydrocarbon migration. The first phase probably took place in Upper Silurian to Lower Devonian time......, when the Alum Shale entered the oil window. These hydrocarbons are mostly found as pyrobitumen in primary voids and calcite cemented veins in Cambro-Silurian sedimentary deposits. The second phase is probably of Late Carboniferous/Permian age and was due to the increased heat flow during the formation...

  15. AD1995: NW Europe's hydrocarbon industry

    International Nuclear Information System (INIS)

    Glennie, K.; Hurst, A.

    1996-01-01

    This volume concerns itself with wide-ranging aspects of the upstream hydro-carbon industry over the whole of NW Europe. As such, the book contrasts with many thematic volumes by presenting a broad range of topics side-by-side. One section of the book looks back at the history of geological exploration and production, and provides an overview of hydrocarbon exploration across NW Europe. Another section covers the state of the art in hydrocarbon exploration and production. This includes an update on computer-based basin modelling overpressure systems, innovations in reservoir engineering and reserve estimation, 3D seismic and the geochemical aspects of secondary migration. The final section of the book takes a look into the future. This covers the remaining hydrocarbon resources of the North Sea, managing risk in oil field development, oil field economics, and pollution and the environment. It is the editors' hope that several key areas of NW Europe's upstream oil industry have been usefully summarized in the volume. (Author)

  16. People Capability Maturity Model. SM.

    Science.gov (United States)

    1995-09-01

    tailored so it consumes less time and resources than a traditional software process assessment or CMU/SEI-95-MM-02 People Capability Maturity Model...improved reputation or customer loyalty. CMU/SEI-95-MM-02 People Capability Maturity Model ■ L5-17 Coaching Level 5: Optimizing Activity 1...Maturity Model CMU/SEI-95-MM-62 Carnegie-Mellon University Software Engineering Institute DTIC ELECTE OCT 2 7 1995 People Capability Maturity

  17. Exploring Unconventional Hydrocarbons in the Makó Trough, Pannonian basin, Hungary: Results and Challenges

    Science.gov (United States)

    Horvath, Anita; Bada, Gabor; Szafian, Peter; Sztano, Orsolya; Law, Ben; Wallis, Rod

    2010-05-01

    the potential reservoirs yield a cell volume as great as several hundred km3 - the largest single prospective gas occurrence in Hungary to date. Due to its novelty and complexity, the exploration of this unconventional resource demands the concurrent application of a wider range of geological and geophysical methods. In this presentation, we use selected examples to give an idea of where we stand on the way toward understanding the Makó Trough, particularly in terms of the geometric and structural features of the basin, the depositional (basin-fill) processes, and of the maturation history and accumulation properties of hydrocarbons. The geophysical surveys were purpose-designed to enable the mapping of the deep sedimentary trough and the sediments deposited in it. The data acquired to date suggest that the basin-centered gas accumulation occurred in the Lower Pannonian strata (11-6? Ma). Interpreting the 3D seismic data, the structural features and sedimentology of the basin can be studied in excellent resolution, while the integration of the seismic information with the geological data obtained from the wells allows us to interpret local well information extensively to gain a deeper, three-dimensional understanding of the basin. The sedimentary sequence filling up the Makó Trough displays distinct stratigraphic units separated by unconformities. Mapping the top of the pre-Neogene basement provides valuable insight into the nature of the paleo-geomorphological elements and the sedimentary environment at the onset of rifting. Paleontological information dates the syn-rift sediments of the trough to the Late Miocene (Early Pannonian), suggesting that the most intensive phase of basin evolution here was delayed by a few million years compared to adjacent areas. For the environmental reconstruction of the post-rift sedimentary sequence, we start with the assumption that initially a starved basin existed here, where sedimentation could not keep up with the rate of

  18. Maturity effects in energy futures

    Energy Technology Data Exchange (ETDEWEB)

    Serletis, Apostolos (Calgary Univ., AB (CA). Dept. of Economics)

    1992-04-01

    This paper examines the effects of maturity on future price volatility and trading volume for 129 energy futures contracts recently traded in the NYMEX. The results provide support for the maturity effect hypothesis, that is, energy futures prices to become more volatile and trading volume increases as futures contracts approach maturity. (author).

  19. Distribution and Thermal Maturity of Devonian Carbonate Reservoir Solid Bitumen in Desheng Area of Guizhong Depression, South China

    Directory of Open Access Journals (Sweden)

    Yuguang Hou

    2017-01-01

    Full Text Available The distribution of solid bitumen in the Devonian carbonate reservoir from well Desheng 1, Guizhong Depression, was investigated by optical microscope and hydrocarbon inclusions analysis. Vb and chemical structure indexes measured by bitumen reflectance, laser Raman microprobe (LRM, and Fourier transform infrared spectroscopy (FTIR were carried out to determine the thermal maturity of solid bitumen. Based on the solid bitumen thermal maturity, the burial and thermal maturity history of Devonian carbonate reservoir were reconstructed by basin modeling. The results indicate that the fractures and fracture-related dissolution pores are the main storage space for the solid bitumen. The equivalent vitrinite reflectance of solid bitumen ranges from 3.42% to 4.43% converted by Vb (% and LRM. The infrared spectroscopy analysis suggests that there are no aliphatic chains detected in the solid bitumen which is rich in aromatics C=C chains (1431–1440 cm−1. The results of Vb (%, LRM, and FTIR analysis demonstrate that the solid bitumen has experienced high temperature and evolved to the residual carbonaceous stage. The thermal evolution of Devonian reservoirs had experienced four stages. The Devonian reservoirs reached the highest reservoir temperature 210–260°C during the second rapid burial-warming stage, which is the main period for the solid bitumen formation.

  20. Distilling hydrocarbons, etc

    Energy Technology Data Exchange (ETDEWEB)

    Turner, C

    1917-11-23

    In the fractional or destructive distillation of hydrocarbon oils or other liquids, the pressure in the still is raised and lowered alternately. The still is closed to raise the pressure, and is opened to lower the pressure rapidly solely by expansion of the vapors. The operation is effected without intermittent cooling, except such as may occur during the lowering of the pressure. In distilling hydrocarbon oil, pressure steam is blown into the oil until the pressure reaches 5 lb/in./sup 2/. The vapor outlet is then opened until the pressure falls to 2 lb/in./sup 2/, whereupon the vapor outlet is closed and steam is again admitted. The operation is continued until the steam, which is of 20 lb pressure, no longer effects distillation; after this stage, superheated steam is used.

  1. Distilling hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    Tausz, J

    1924-07-16

    Hydrocarbon oils such as petroleum, shale oils, lignite or coal tar oils are purified by distilling them and collecting the distillate in fractions within narrow limits so that all the impurities are contained in one or more of the narrow fractions. In distilling ligroin obtained by destructive distillation of brown coal, it is found that the coloring and resin-forming constituents are contained in the fractions distilling over at 62 to 86/sup 0/C and 108/sup 0/C. The ligroin is purified, therefore, by distillating in an apparatus provided with an efficient dephlegmotor and removing these two fractions. The distillation may be carried out wholly or in part under reduced pressure, and fractions separated under ordinary pressure may be subsequently distilled under reduced pressure. The hydrocarbons may be first separated into fractions over wider limits and the separate fractions be subjected to a further fractional distillation.

  2. Nuclear explosives and hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, P

    1971-10-01

    A nuclear explosive 12 in. in diam and producing very little tritium is feasible in France. Such a device would be well adapted for contained nuclear explosions set off for the purpose of hydrocarbon storage or stimulation. The different aspects of setting off the explosive are reviewed. In the particular case of gas storage in a nuclear cavity in granite, it is demonstrated that the dose of irradiation received is extremely small. (18 refs.)

  3. Treatment of hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    1936-02-22

    A process is described for refining a mixture of liquid hydrocarbons containing harmful substances, this process permitting the operation, which consists in treating the liquid mixture at a temperature higher than 200/sup 0/C with a solid catalyst of phosphoric acid, consisting of phosphoric acid deposited on a solid support of the type of metallurgical coke, for a time sufficient to convert the harmful components to inoffensive substances.

  4. Cracking hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    Seigle, A A.F.M.

    1922-12-20

    Hydrocarbon oils such as petroleum, peat, shale, or lignite oils, heavy tars, resin oils, naphthalene oils, etc., are vaporized by being fed from a tank through a preheater to the lower part of a vertical annular retort heated by a flame projected down the central cavity from a burner. The oil vapors rise through annular passages formed by disks, on which are placed chips of copper, iron, aluminum, etc., to act as catalysts.

  5. High boiling point hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Pier, M

    1929-04-29

    A process is given for the production of hydrocarbons of high boiling point, such as lubricating oils, from bituminous substances, such as varieties of coal, shale, or other solid distillable carbonaceous materials. The process consists of treating the initial materials with organic solvents and then subjecting the products extracted from the initial materials, preferably directly, to a reducing treatment in respect to temperature, pressure, and time. The reduction treatment is performed by means of hydrogen under pressure.

  6. Direct hydrocarbon fuel cells

    Science.gov (United States)

    Barnett, Scott A.; Lai, Tammy; Liu, Jiang

    2010-05-04

    The direct electrochemical oxidation of hydrocarbons in solid oxide fuel cells, to generate greater power densities at lower temperatures without carbon deposition. The performance obtained is comparable to that of fuel cells used for hydrogen, and is achieved by using novel anode composites at low operating temperatures. Such solid oxide fuel cells, regardless of fuel source or operation, can be configured advantageously using the structural geometries of this invention.

  7. Antibody affinity maturation

    DEFF Research Database (Denmark)

    Skjødt, Mette Louise

    Yeast surface display is an effective tool for antibody affinity maturation because yeast can be used as an all-in-one workhorse to assemble, display and screen diversified antibody libraries. By employing the natural ability of yeast Saccharomyces cerevisiae to efficiently recombine multiple DNA...... laboratory conditions. A particular emphasis was put on using molecular techniques in conjunction with microenvironmental measurements (O2, pH, irradiance), a combination that is rarely found but provides a much more detailed understanding of “cause and effect” in complex natural systems...

  8. The Role of Geochemistry and Basin Modelling in the Exploration of Mature province

    International Nuclear Information System (INIS)

    Katz, A.J.

    2002-01-01

    Petroleum geochemistry and basin modelling has been an important tool in the reduction of risks in poorly explored basins. Historically the role of geochemistry is usually reduced once production is established and often in mature province is nonexistent. However, attempts to add reserves in mature provinces require an expansion of exploration programs based on new play concepts. Consequently, there is a clear role for geochemistry and basin modelling as this revitalization occurs.These new basin modelling and geochemical programs are aimed at answering three questions: . Can the petroleum system be extended? . Is a change in hydrocarbon character to be expected? . How much hydrocarbon potential remains?Unlike frontier exploration a significant sample base is normally available that can be used to more effectively constrain interpretations. Such programs have clearly aided exploration in the Niger Delta. For example, the collection of an extensive piston core dataset in conjunction with a basin modelling program provided strong support for the Niger Delta's petroleum system extending into deep water areas. While the geochemical character of the oils established the presence of multiple effective generative systems, each of which has different source characteristics and often-different ages. This information constraints model construction and hydrocarbon volume estimates. Oil data also established the importance of phase segregation. The presence of fractionated oils and maturation modelling results provides evidence for deeper hydrocarbon potential within the geographic limits of established hydrocarbon pays

  9. ) Geochemistry and Hydrocarbon Potential of Cretaceous Shales in the Chad Basin

    International Nuclear Information System (INIS)

    Alalade, B.; Ogunyemi, A. T.; Abimbola, A.F.; Olugbemiro, R. O.

    2003-01-01

    The Chad Basin is the largest intracratonic basin in Africa and is filled with more than 400m of Cretaceous to Recent sediments. Geochemical and petrographic studies of Cretaceous shales form the Bima, Gongola and Fika Formations were carried out to establish their hydrocarbon potential and thermal maturity. Ditch cuttings of the shales were collected from the Wa di and Karen's exploration wells located in the Nigerian sector of the Chad Basin.The geochemical analysis of the shales indicate that, except for Si02 and K20, all other oxides (Mg O, Fe2O3, AL2O3, CaO) are more abundant in the Fika shale than the Gongola shale. This suggests a more marine condition for the Fika shale compared to the Gongola shale. The Fika and Gongola shales were further classified into Iron shale and shale respectively. Organic carbon contents of the Bima, Gongola and exceed the minimum (0.5wt%) usually required for siliciclastic petroleum source rock. However, the soluble organic matter (SOM) and saturated hydrocarbon (SHC) contents of the shales, which ranges from 108pm to 743ppm and 23ppm to 100ppm respectively, are generally low and are therefore, organically lean. The organic matter of the shales is predominantly terrestrially derived, vitrinite rich, Type III kerogen and are therefore, gas prone. Thermal maturity assessed from SOM/TOC, SHC/TOC ratios and spore color index (SCI) indicate that the Fika shale is immature while the Gongola and Bima shales are within the oil window

  10. Guidelines for Applying the Capability Maturity Model Analysis to Connected and Automated Vehicle Deployment

    Science.gov (United States)

    2017-11-23

    The Federal Highway Administration (FHWA) has adapted the Transportation Systems Management and Operations (TSMO) Capability Maturity Model (CMM) to describe the operational maturity of Infrastructure Owner-Operator (IOO) agencies across a range of i...

  11. Site characterization and petroleum hydrocarbon plume mapping

    Energy Technology Data Exchange (ETDEWEB)

    Ravishankar, K. [Harding Lawson Associates, Houston, TX (United States)

    1996-12-31

    This paper presents a case study of site characterization and hydrocarbon contamination plume mapping/delineation in a gas processing plant in southern Mexico. The paper describes innovative and cost-effective use of passive (non-intrusive) and active (intrusive) techniques, including the use of compound-specific analytical methods for site characterization. The techniques used, on a demonstrative basis, include geophysical, geochemical, and borehole drilling. Geochemical techniques used to delineate the horizontal extent of hydrocarbon contamination at the site include soil gas surveys. The borehole drilling technique used to assess the vertical extent of contamination and confirm geophysical and geochemical data combines conventional hollow-stem auguring with direct push-probe using Geoprobe. Compound-specific analytical methods, such as hydrocarbon fingerprinting and a modified method for gasoline range organics, demonstrate the inherent merit and need for such analyses to properly characterize a site, while revealing the limitations of noncompound-specific total petroleum hydrocarbon analysis. The results indicate that the techniques used in tandem can properly delineate the nature and extent of contamination at a site; often supplement or complement data, while reducing the risk of errors and omissions during the assessment phase; and provide data constructively to focus site-specific remediation efforts. 7 figs.

  12. Study of Kerogen Maturity using Transmission Fourier Transform Infrared Spectroscopy (FTIR)

    Science.gov (United States)

    Dang, S. T.

    2014-12-01

    Maturity of kerogen in shale governs the productivity and generation hydrocarbon type. There are generally two accepted methods to measure kerogen maturity; one is the measurement of vitrinite reflectance, %Ro, and another is the measurement of Tmax through pyrolysis. However, each of these techniques has its own limits; vitrinite reflectance measurement cannot be applied to marine shale and pre-Silurian shales, which lack plant materials. Furthermore, %Ro, requires the isolation and identification of vitrinite macerals and statistical measurements of at least 50 macerals. Tmax measurement is questionable for mature and post-mature samples. In addition, there are questions involving the effects of solvents on Tmax determinations. Fourier Transmission Infrared Spectroscopy, FTIR, can be applied for both qualitative and quantitative assessment on organics maturity in shale. The technique does not require separating organic matter or identifying macerals. A CH2/CH3 index, RCH, calculated from FTIR spectra is more objective than other measurements. The index increases with maturity (both natural maturation and synthetic maturation through hydrous and dry pyrolysis). The new maturity index RCH can be calibrated to vitrinite reflectance which allows the definition of the following values for levels of maturity: 1) immature—RCH > 1.6±0.2; 2) oil window-- 1.6±0.2 1.3±0.3; 3) wet gas window--1.3±0.3 1.13±0.05; and 4) dry gas window RCH < 1.13±0.05.

  13. Catalytic Upgrading of Sugars to Hydrocarbons Technology Pathway

    Energy Technology Data Exchange (ETDEWEB)

    Biddy, M.; Jones, S.

    2013-03-01

    This technology pathway case investigates the catalytic conversion of solubilized carbohydrate streams to hydrocarbon biofuels, utilizing data from recent efforts within the National Advanced Biofuels Consortium (NABC) in collaboration with Virent, Inc. Technical barriers and key research needs that should be pursued for the catalytic conversion of sugars pathway to be competitive with petroleum-derived gasoline-, diesel-, and jet-range hydrocarbon blendstocks have been identified.

  14. Process and catalyst for the catalytic conversion of hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    1939-10-27

    A process is disclosed for converting hydrocarbon oils of higher than gasoline end boiling point, into large yields of motor fuel of high anti-knock value and substantial yields of normally gaseous readily polymerizable olefins, which comprises subjecting said hydrocarbon oils at a temperature within the approximate range of 425 to 650/sup 0/C. to contact with a catalytic material comprising hydrated silica and hydrated zirconia substantially free from alkali metal compounds.

  15. Measuring Trace Hydrocarbons in Silanes

    Science.gov (United States)

    Lesser, L. A.

    1984-01-01

    Technique rapid and uses standard analytical equipment. Silane gas containing traces of hydrocarbons injected into carrier gas of moist nitrogen having about 0.2 percent water vapor. Carrier, water and silane pass through short column packed with powdered sodium hydroxide which combines moisture and silane to form nonvolatile sodium silicate. Carrier gas free of silane but containing nonreactive hydrocarbons, pass to silica-gel column where chromatographic separation takes place. Hydrocarbons measured by FID.

  16. Fractional separation of hydrocarbon vapours

    Energy Technology Data Exchange (ETDEWEB)

    1937-07-10

    A process is described for converting higher boiling hydrocarbons to lower boiling hydrocarbons by subjecting them at elevated temperatures to a conversion operation, then separating the higher and lower boiling fractions. The separation takes place while the reaction products are maintained in the vapor phase by contact with a mass of solid porous material which has little or no catalytic activity but does have a preferential absorption property for higher boiling hydrocarbons so that the lower boiling part of the reaction products pass through the separation zone while the heavier hydrocarbons are retained. The separation is accomplished without substantial loss of heat of these reaction products.

  17. Mature Cystic Renal Teratoma

    International Nuclear Information System (INIS)

    Yavuz, Alpaslan; Ceken, Kagan; Alimoglu, Emel; Akkaya, Bahar

    2014-01-01

    Teratomas are rare germline tumors that originate from one or more embryonic germ cell layers. Teratoma of the kidney is extremely rare, and less than 30 cases of primary intrarenal teratomas have been published to date. We report the main radiologic features of an unusual case of mature cystic teratoma arising from the left kidney in a two-year-old boy. A left-sided abdominal mass was detected on physical examination and B-Mod Ultrasound (US) examination revealed a heterogeneous mass with central cystic component. Computed tomography (CT) demonstrated a lobulated, heterogeneous, hypodense mass extending craniocaudally from the splenic hilum to the level of the left iliac fossa. Nephrectomy was performed and a large, fatty mass arising from the left kidney was excised. The final pathologic diagnosis was confirmed as cystic renal teratoma

  18. Process for preparing hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Krauch, C; Anther, E; Pier, M

    1926-04-07

    A process is described for the conversion of coal of all kinds, wood, oil, shale, as well as other carbonaceous materials into liquid hydrocarbons in two steps, characterized by treatment of the coal and so forth with a stream of hydrogen or hydrogen-containing gases at raised temperatures and raised pressures and producing a tarry product which, after separation of the ashlike residue, is converted by a further treatment, in the presence of catalysts, with hydrogen or hydrogen-containing gases at raised temperature and pressure, largely into low-boiling products.

  19. Recovering valuable liquid hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Pier, M

    1931-06-11

    A process for recovering valuable liquid hydrocarbons from coking coal, mineral coal, or oil shale through treatment with hydrogen under pressure at elevated temperature is described. Catalysts and grinding oil may be used in the process if necessary. The process provides for deashing the coal prior to hydrogenation and for preventing the coking and swelling of the deashed material. During the treatment with hydrogen, the coal is either mixed with coal low in bituminous material, such as lean coal or active coal, as a diluent or the bituminous constituents which cause the coking and swelling are removed by extraction with solvents. (BLM)

  20. Hydrogen production from hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Docekal, J

    1986-01-01

    Hydrogen is an important feed stock for chemical and petroleum industries, in addition to being considered as the energy carrier of the future. At the present time the feed stock hydrogen is mainly manufactured from hydrocarbons using steam reforming. In steam reforming two processes are employed, the conventional process and PSA (pressure swing adsorption) process. These two processes are described and compared. The results show that the total costs and the maintenance costs are lower for the PSA process, the capital outlay is lower for the conventional process, and the operating costs are similar for the two processes.

  1. Distribution and origin of hydrocarbons in water and sediment in Sao Sebastiao, SP, Brazil

    International Nuclear Information System (INIS)

    Zanardi, Eliete; Bicego, Marcia Caruso; Miranda, Luiz Bruner de; Weber, Rolf Roland

    1999-01-01

    This study describes the dissolved/dispersed petroleum hydrocarbons (DDPH) in surface water and the origin and distribution of aliphatic and aromatic hydrocarbons in samples from the surface bottom sediments. The main objective was to verify the anthropogenic contribution on the adjacent inner shelf of Sao Sebastiao, taking into account the distribution of hydrographic properties and knowledge of the main circulation. The DDPH concentration range of the 20 samples were from 0.35 to 2.50 m u g . L -1 , characterising this region as slightly affected by the contribution of petroleum hydrocarbons. Considering sediment hydrocarbon results, sites located in the inner shelf were divided into three groups: one with mainly biogenic hydrocarbons, a second one with biogenic and petroleum hydrocarbons and a third with significant contribution of petroleum hydrocarbons. These results show an influence of human activities in the Sao Sebastiao Channel on the surrounding areas of the inner shelf. (Author)

  2. Distribution and origin of hydrocarbons in water and sediment in Sao Sebastiao, SP, Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Zanardi, Eliete [Universidade de Sao Paulo, Instituto Oceanografico, Sao Paulo, SP (Brazil); Bicego, Marcia Caruso; Miranda, Luiz Bruner de; Weber, Rolf Roland [Miami Univ., RSMAS/NAC, Miami, FL (United States)

    1999-04-01

    This study describes the dissolved/dispersed petroleum hydrocarbons (DDPH) in surface water and the origin and distribution of aliphatic and aromatic hydrocarbons in samples from the surface bottom sediments. The main objective was to verify the anthropogenic contribution on the adjacent inner shelf of Sao Sebastiao, taking into account the distribution of hydrographic properties and knowledge of the main circulation. The DDPH concentration range of the 20 samples were from 0.35 to 2.50 {sup m}u{sup g}. L{sup -1}, characterising this region as slightly affected by the contribution of petroleum hydrocarbons. Considering sediment hydrocarbon results, sites located in the inner shelf were divided into three groups: one with mainly biogenic hydrocarbons, a second one with biogenic and petroleum hydrocarbons and a third with significant contribution of petroleum hydrocarbons. These results show an influence of human activities in the Sao Sebastiao Channel on the surrounding areas of the inner shelf. (Author)

  3. Structural segregation of petroleum and prospective hydrocarbon regions in Azerbaijan

    International Nuclear Information System (INIS)

    Kerimov, K.M.; Huseynov, A.N.; Hajiyev, F.M.

    2002-01-01

    Full text : Structural segregation allows identify the earth crust blocks according to their geological setting and structural history conductive for hydrocarbon generation and their entrapment in the sedimentary fill reservoirs. Since then there has been a need to design a new tectonic map of petroleum and hydrocarbons potential systems in Azerbaijan embracing both on- and offshore areas. Map's legend designed upon above mentioned concepts and principles has made it possible to evaluate the role of individual stratigraphic units in hydrocarbon generation and its entrapment, as well as in recognition of regional structural criteria of the hydrocarbon bearing potential of different structural patterns. Tectonic map of petroleum and prospective hydrocarbon bearing on and offshore areas in Azerbaijan for the first time contained a wide range of information related to structural criteria of hydrocarbon bearing potential, sedimentary fill's structural architecture, its thickness, both timing of their formation stages and basement consolidation, its subsidence depth, as well as hydrocarbon deposit areal and vertical distribution across individual regions. This map was considered to be of important implication both for the petroleum geoscience and petroleum industry endeavors.

  4. Risk analysis associated with petroleum hydrocarbons: is everything running smoothly?

    International Nuclear Information System (INIS)

    Morin, D.

    1999-01-01

    Petroleum products represent one of the main sources of environmental contamination, and these products are complex, composed of several hundred individual hydrocarbons. The evaluation of the risks associated with petroleum products is often limited by certain specific parameters such as benzene. The petroleum hydrocarbons running from C(10) to C(50) are not often integrated in an analysis of the toxological risks since the toxological characterization of a complex mixture of hydrocarbons is difficult to carry out. There exist in the United States two approaches that were developed recently that allow the integration of various hydrocarbons comprising a mixture. In this presentation, two of these approaches are described and compared. An overview of these approaches related to Canadian regulatory bodies is included, and a case study completes the account. The two approaches that are most well known in this area are: 1) that of the Massachusetts Dept. of Environmental Protection, and 2) that of the Total Petroleum Hydrocarbon Criteria Working Group. The integration of petroleum hydrocarbons in a quantitative evaluation of their toxological risk is possible by present methods. This integration allows a reduction in the uncertainty associated with the use of an integrating parameter in the case of these petroleum hydrocarbons in the C(10) to the C(50) range

  5. Developing maturity grids for assessing organisational capabilities

    DEFF Research Database (Denmark)

    Maier, Anja; Moultrie, James; Clarkson, P John

    2009-01-01

    Keyword: Maturity Model,Maturity Grid,Maturity Matrix,Organisational Capabilities,Benchmarking,New Product Development,Perfirmance Assessment......Keyword: Maturity Model,Maturity Grid,Maturity Matrix,Organisational Capabilities,Benchmarking,New Product Development,Perfirmance Assessment...

  6. Modeling non-maturing liabilities

    OpenAIRE

    von Feilitzen, Helena

    2011-01-01

    Non‐maturing liabilities, such as savings accounts, lack both predetermined maturity and reset dates due to the fact that the depositor is free to withdraw funds at any time and that the depository institution is free to change the rate. These attributes complicate the risk management of such products and no standardized solution exists. The problem is important however since non‐maturing liabilities typically make up a considerable part of the funding of a bank. In this report different mode...

  7. Systems and processes for conversion of ethylene feedstocks to hydrocarbon fuels

    Science.gov (United States)

    Lilga, Michael A.; Hallen, Richard T.; Albrecht, Karl O.; Cooper, Alan R.; Frye, John G.; Ramasamy, Karthikeyan Kallupalayam

    2018-04-03

    Systems, processes, and catalysts are disclosed for obtaining fuel and fuel blends containing selected ratios of open-chain and closed-chain fuel-range hydrocarbons suitable for production of alternate fuels including gasolines, jet fuels, and diesel fuels. Fuel-range hydrocarbons may be derived from ethylene-containing feedstocks and ethanol-containing feedstocks.

  8. Systems and processes for conversion of ethylene feedstocks to hydrocarbon fuels

    Science.gov (United States)

    Lilga, Michael A.; Hallen, Richard T.; Albrecht, Karl O.; Cooper, Alan R.; Frye, John G.; Ramasamy, Karthikeyan Kallupalayam

    2017-09-26

    Systems, processes, and catalysts are disclosed for obtaining fuels and fuel blends containing selected ratios of open-chain and closed-chain fuel-range hydrocarbons suitable for production of alternate fuels including gasolines, jet fuels, and diesel fuels. Fuel-range hydrocarbons may be derived from ethylene-containing feedstocks and ethanol-containing feedstocks.

  9. Reservoir petrophysics and hydrocarbon occurrences of the Bahariya Formation, Alamein-Yidma fields, Western Desert of Egypt

    Energy Technology Data Exchange (ETDEWEB)

    Abdel-Aziz Younes, Mohamed [Alexandria Univ. (Egypt). Geology Dept.

    2012-12-15

    The Bahariya Formation of Cenomanian age is considered to be one of the main oil and gas accumulations in most of the fields of the Western Desert basins. The lithostratigraphic succession of the Bahariya Formation is classified into two main sand units (Unit I and Unit III) separated by shalesiltstone (Unit II). The sandstone of unit-I and III is characterized by being highly enriched in shale content especially glauconite in all wells of the Alamein Field, that has an obvious negative effect on the porosity and oil saturation, where the glauconite increases the grain density of sandstone reservoirs from 2.65 g/cm{sup 3} up to 2.71 g/cm{sup 3}. The well logging data and petrophysical characteristics conducted on Alamein well-28 involving analysis of 30 core samples, were used to evaluate the reservoir characterization and hydrocarbon potentialities. The petrophysical parameters indicate that the primary porosity values are between 8.7 and 29.1%. Decreasing porosity is related to the increase of shale content from 9 to 13%, which occurs as a dispersed habitat. The water saturation changes from 43 to 80%, while the hydrocarbon saturation ranges from 12.1 to 37%. Promising hydrocarbon accumulations are displayed by the sandstone of unit-III due to increased hydrocarbon saturation and effective porosity, thus reflecting the high quality reservoir of this unit. The irreducible and movable hydrocarbon distribution shows a general increase at the eastern and western flanks of the faulted anticline in the Alamein-Yidma fields. The biomarker characteristics and stable carbonisotopic composition of the Bahariya crude oils recovered from the Alamein Field show no obvious variations among them. These oils are paraffinic, containing little branched or cyclic materials waxy n-alkanes(C{sub 25}-C{sub 31}) and characterized by high API gravity, low sulfur content, oleanane index < 2% and moderately high pristane/phytaneratio > 1 and CPI > 1 and the canonical variable parameter is

  10. Natural hydrocarbon seeps observation with underwater gliders and UV fluorescence sensor

    Science.gov (United States)

    Rochet, V.

    2016-02-01

    Hydrocarbons may leak to the near-surface from subsurface accumulations, from mature source rock, or by buoyancy along major cross-strata routes. The presence of migrating near-surface hydrocarbons can provide strong evidence for the presence of a working petroleum system, as well as valuable information on source, maturity, and migration pathways. Detection and characterization of hydrocarbons in the water column may then help to de-risk hydrocarbon plays at a very preliminary stage of an exploration program. In order to detect hydrocarbons in the water column, an underwater glider survey was conducted in an offshore frontier area. Driven by buoyancy variation, underwater gliders enable collecting data autonomously along the water column for weeks to months. Underwater gliders are regularly piloted from shore by satellite telemetry and do not require a surface supervising vessel resulting in substantial operational costs savings. The data compiled, over 700m depth of the water column, included temperature, salinity, pressure, dissolved oxygen and hydrocarbon components (phenanthrene and naphthalene) measured by "MINIFLUO" sensors to particularly target representative crude oil compounds Two gliders were deployed at sea, one from coast in shallow water and the other one offshore on the survey area. Both accurately squared the survey area following pre-defined lines and cross lines. Data files were transmitted by satellite telemetry in near real time during the performance of the mission for real time observations and appropriate re-positioning of the gliders. Using rechargeable underwater gliders increased reliability reducing the risk of leakage and associated logistics during operation at sea. Despite strong evidences of seabed seepages such as pockmarks, faults, etc, over the area of interest, no hydrocarbon indices were detected in the water column, which was confirmed later by seabed sample analysis. The use of glider platforms for hydrocarbon detection has

  11. Determination of polynuclear hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Lodge, Jr, J P

    1963-01-01

    At the present time, the method of choice for the determination of polynuclear hydrocarbons appears to be the following, (a) extraction of the benzene-soluble fraction from the gross collected particulate matter, (b) one pass through a chromatographic column of partially deactivated alumina, (c) spectral examination of the fractions and (d) the application of appropriate chemical tests as indicated by the previous step. Using this method, the presence of pyrene, fluoranthene, one of the benzofluorenes, chrysens, benz(a)anthracene, benzo(a)pyrene, benzo(e)pyrene, benzo(k)fluoranthene, anthanthrene, and coronene was demonstrated in the air of numerous American cities, and benzo(a)pyrene was measured at some 130 sites. Invaluable as such accurate determinations may be for research purposes, they are still too costly and time-consuming for routine survey purposes. While studies on the subject are by no means complete, they indicate the validity of piperonal chloride test as a general index of polycyclic hydrocarbons. This procedure is described in this paper. 7 references.

  12. Hydrocarbons: source of energy

    International Nuclear Information System (INIS)

    Imarisio, G.; Frias, M.; Bemtgen, J.M.

    1989-01-01

    Hydrocarbons are at present the single most important source of energy, since they are the most versatile and widely used. It is expected that their importance will extend well into the next century and therefore it is essential to provide for all those improvements which will extend their availability and usefulness. The sub-programme ''Optimization of the production and utilization of hydrocarbons'' (within the Non-Nuclear Energy R and D Programme of the European Communities) is pursuing a number of R and D topics aimed at the above-mentioned results. It is implemented by means of shared-cost R and D contracts. At this first Seminar held in Lyon (France) from 21-23 September, 1988, all contractors of the sub-programme presented the state of progress of their R and D projects. These proceedings comprise all the papers presented at the Seminar. The section on oilfield exploration includes a report of work on the interpretation of nuclear logs by means of mathematical models. (author)

  13. Liquid hydrocarbon generation potential from Tertiary Nyalau Formation coals in the onshore Sarawak, Eastern Malaysia

    Science.gov (United States)

    Hakimi, Mohammed Hail; Abdullah, Wan Hasiah

    2013-01-01

    Tertiary coals exposed in the north-central part of onshore Sarawak are evaluated, and their depositional environments are interpreted. Total organic carbon contents (TOC) of the coals range from 58.1 to 80.9 wt. % and yield hydrogen index values ranging from 282 to 510 mg HC/g TOC with low oxygen index values, consistent with Type II and mixed Type II-III kerogens. The coal samples have vitrinite reflectance values in the range of 0.47-0.67 Ro %, indicating immature to early mature (initial oil window). T max values range from 428 to 436 °C, which are good in agreement with vitrinite reflectance data. The Tertiary coals are humic and generally dominated by vitrinite, with significant amounts of liptinite and low amounts of inertinite macerals. Good liquid hydrocarbons generation potential can be expected from the coals with rich liptinitic content (>35 %). This is supported by their high hydrogen index of up to 300 mg HC/g TOC and Py-GC ( S 2) pyrograms with n-alkane/alkene doublets extending beyond C30. The Tertiary coals are characterised by dominant odd carbon numbered n-alkanes ( n-C23 to n-C33), high Pr/Ph ratio (6-8), high T m / T s ratio (8-16), and predominant regular sterane C29. All biomarkers parameters clearly indicate that the organic matter was derived from terrestrial inputs and the deposited under oxic condition.

  14. Steam hydrocarbon cracking and reforming

    NARCIS (Netherlands)

    Golombok, M.

    2004-01-01

    Many industrial chemical processes are taught as distinct contrasting reactions when in fact the unifying comparisons are greater than the contrasts. We examine steam hydrocarbon reforming and steam hydrocarbon cracking as an example of two processes that operate under different chemical reactivity

  15. Hydrocarbon productivities in different Botryococcus strains: comparative methods in product quantification.

    Science.gov (United States)

    Eroglu, Ela; Okada, Shigeru; Melis, Anastasios

    2011-08-01

    Six different strains of the green microalgae Botryococcus belonging to the A-race or B-race, accumulating alkadiene or botryococcene hydrocarbons, respectively, were compared for biomass and hydrocarbon productivities. Biomass productivity was assessed gravimetrically upon strain growth in the laboratory under defined conditions. Hydrocarbon productivities were measured by three different and independent experimental approaches, including density equilibrium of the intact cells and micro-colonies, spectrophotometric analysis of hydrocarbon extracts, and gravimetric quantitation of eluted hydrocarbons. All three hydrocarbon-quantitation methods yielded similar results for each of the strains examined. The B-race microalgae Botryococcus braunii var. Showa and Kawaguchi-1 constitutively accumulated botryococcene hydrocarbons equivalent to 30% and 20%, respectively, of their overall biomass. The A-race microalgae Botryococcus braunii, varieties Yamanaka, UTEX 2441 and UTEX LB572 constitutively accumulated alkadiene hydrocarbons ranging from 14% to 13% and 10% of their overall biomass, respectively. Botryococcus sudeticus (UTEX 2629), a morphologically different green microalga, had the lowest hydrocarbon accumulation, equal to about 3% of its overall biomass. Results validate the density equilibrium and spectrophotometric analysis methods in the quantitation of botryococcene-type hydrocarbons. These analytical advances will serve in the screening and selection of B. braunii and of other microalgae in efforts to identify those having a high hydrocarbon content for use in commercial applications.

  16. Characterization of a nose-only inhalation exposure system for hydrocarbon mixtures and jet fuels.

    Science.gov (United States)

    Martin, Sheppard A; Tremblay, Raphael T; Brunson, Kristyn F; Kendrick, Christine; Fisher, Jeffrey W

    2010-04-01

    A directed-flow nose-only inhalation exposure system was constructed to support development of physiologically based pharmacokinetic (PBPK) models for complex hydrocarbon mixtures, such as jet fuels. Due to the complex nature of the aerosol and vapor-phase hydrocarbon exposures, care was taken to investigate the chamber hydrocarbon stability, vapor and aerosol droplet compositions, and droplet size distribution. Two-generation systems for aerosolizing fuel and hydrocarbons were compared and characterized for use with either jet fuels or a simple mixture of eight hydrocarbons. Total hydrocarbon concentration was monitored via online gas chromatography (GC). Aerosol/vapor (A/V) ratios, and total and individual hydrocarbon concentrations, were determined using adsorbent tubes analyzed by thermal desorption-gas chromatography-mass spectrometry (TDS-GC-MS). Droplet size distribution was assessed via seven-stage cascade impactor. Droplet mass median aerodynamic diameter (MMAD) was between 1 and 3 mum, depending on the generator and mixture utilized. A/V hydrocarbon concentrations ranged from approximately 200 to 1300 mg/m(3), with between 20% and 80% aerosol content, depending on the mixture. The aerosolized hydrocarbon mixtures remained stable during the 4-h exposure periods, with coefficients of variation (CV) of less than 10% for the total hydrocarbon concentrations. There was greater variability in the measurement of individual hydrocarbons in the A-V phase. In conclusion, modern analytical chemistry instruments allow for improved descriptions of inhalation exposures of rodents to aerosolized fuel.

  17. Analysis of monoterpene hydrocarbons in rural atmospheres

    International Nuclear Information System (INIS)

    Holdren, M.W.; Westberg, H.H.; Zimmerman, P.R.

    1979-01-01

    Gas chromatographic/mass spectrometric analysis of monoterpenes from a rural forested site in the northwestern United States is described. Use of a glass capillary column provided excellent resolution of the hydrocarbons. Increased sensitivity and specificity of the mass spectrometer detector over the flame ionization detector were demonstrated for trace (parts per trillion) atmospheric hydrocarbons. As little as 10 ppt of compound was detectable in 100-cc air samples. Two analytical methods (cryogenic and solid adsorbent--Tenax-GC) were used in the collection of ambient air. Analytical results from the two techniques compared very well. Rural concentrations of the monoterpenes varied considerably depending upon location within the forest canopy. The concentration of individual species never exceeded 1 ppb of compound during a 10-month sampling period. The monoterpene total for all samples fell in the range of 0.5- to 16-ppb compound for C 10 terpene

  18. Whose Maturity is it Anyway?

    DEFF Research Database (Denmark)

    Lasrado, Lester Allan; Vatrapu, Ravi; Mukkamala, Raghava Rao

    2017-01-01

    This paper presents results from an ongoing empirical study that seeks to understand the influence of different quantitative methods on the design and assessment of maturity models. Although there have been many academic publications on maturity models, there exists a significant lack of understa...

  19. Enumeration of petroleum hydrocarbon utilizing bacteria

    International Nuclear Information System (INIS)

    Mukherjee, S.; Barot, M.; Levine, A.D.

    1996-01-01

    In-situ biological treatment is one among a number of emerging technologies that may be applied to the remediation of contaminated soils and groundwater. In 1985, a surface spill of 1,500 gallons of dielectric transformer oil at the Sandia National Laboratories (HERMES II facility) resulted in contamination of soil up to depths of 160 feet. The extent of contamination and site characteristics favored the application of in-situ bioremediation as a potential remedial technology. The purpose of this research was to enumerate indigenous microbial populations capable of degrading petroleum hydrocarbons. Microbial enumeration and characterization methods suitably adapted for hydrocarbon utilizing bacteria were used as an indicator of the presence of viable microbial consortia in excavated oil samples with hydrocarbon (TPH) concentrations ranging from 300 to 26,850 ppm. Microbial activity was quantified by direct and streak plating soil samples on silica gel media. Effects of toxicity and temperature were studied using batch cultures of hydrocarbon utilizing bacteria (selectively isolated in an enrichment medium), at temperatures of 20 and 35 C. It was concluded from this study that it is possible to isolate native microorganisms from contaminated soils from depths of 60 to 160 feet, and with oil concentration ranging from 300 to 26,850 ppm. About 62% of the microorganisms isolated form the contaminated soil were capable of using contaminant oil as a substrate for growth and metabolism under aerobic conditions. Growth rates were observed to be 50% higher for the highest contaminant concentration at 20 C. Resistance to toxicity to contaminant oil was also observed to be greater at 20 C than at 35 C

  20. Viscosity Prediction of Hydrocarbon Mixtures Based on the Friction Theory

    DEFF Research Database (Denmark)

    Zeberg-Mikkelsen, Claus Kjær; Cisneros, Sergio; Stenby, Erling Halfdan

    2001-01-01

    The application and capability of the friction theory (f-theory) for viscosity predictions of hydrocarbon fluids is further illustrated by predicting the viscosity of binary and ternary liquid mixtures composed of n-alkanes ranging from n-pentane to n-decane for wide ranges of temperature and from...

  1. Canada's hydrocarbon processing evolution

    International Nuclear Information System (INIS)

    Wise, T.H.; Horton, R.

    2000-01-01

    The development of petroleum refining, petrochemicals and natural gas industries in Canada are discussed together with future issues and prospects. Figures give data on (a) refined products trade 1998; (b) refining capacity; (c) product demand 1980-1999; (d) refinery crude runs and capacity; (e) refining and marketing, historical returns 1993-1999; (f) processing power index for Canada and USA; (g) ethylene capacity; (eye) Montreal petrochemical capacities; (j) Sarnia petrochemical capacities in 2000; (k) Alberta petrochemicals capacities 2001; (l) ethylene net equivalent trade; (m) ethylene costs 1999 for W. Canada and other countries. It was concluded that the hydrocarbon processing business continues to expand in Canada and natural gas processing is likely to increase. Petrochemicals may expand in W. Canada, possibly using feed stock from the Far North. Offshore developments may stimulate new processing on the E. Coast

  2. Hydrogenating gaseous hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Nicolardot, P L.F.

    1930-08-06

    Gaseous hydrocarbons obtained by the destructive distillation of carbonaceous materials are simultaneously desulfurized and hydrogenated by passing them at 350 to 500/sup 0/C, mixed with carbon monoxide and water vapor over lime mixed with metallic oxides present in sufficient amount to absorb the carbon dioxide as it is formed. Oxides of iron, copper, silver, cobalt, and metals of the rare earths may be used and are mixed with the lime to form a filling material of small pieces filling the reaction vessel which may have walls metallized with copper and zinc dust. The products are condensed and fixed with absorbents, e.g. oils, activated carbon, silica gels. The metallic masses may be regenerated by a hot air stream and by heating in inert gases.

  3. Treating hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    Scott, R; MacIvor, W

    1869-09-01

    The treatment of hydrocarbon oils, such as coal or shale oils, paraffin oils, and petroleum, either in the crude or more or less refined state has the object of reducing the specific gravity and otherwise improving the qualities of such oils. The oil to be treated is put into any ordinary still and distilled. The vapor escaping during the distillation is passed through one or more heating vessels or chambers and exposed to the heat necessary to produce the change. The heating vessels or chambers may be made of metal, clay, or any other material adapted to endure heat, and they may be made of any desired form, or they may be constituted of a coil of metal pipes or a series of tubes such as are used for heating air for blast furnaces.

  4. Evaluation on occluded hydrocarbon in deep–ultra deep ancient source rocks and its cracked gas resources

    Directory of Open Access Journals (Sweden)

    Jian Li

    2015-12-01

    Full Text Available Oil-cracked gas, as the main type of high-over mature marine natural gas in China, is mainly derived from occluded hydrocarbon. So it is significant to carry out quantitative study on occluded hydrocarbon. In this paper, the occluded hydrocarbon volume of the main basins in China was calculated depending on their types, abundances and evolution stages by means of the forward method (experimental simulation and the inversion method (geologic profile dissection. And then, occluded hydrocarbon evolution models were established for five types of source rocks (sapropelic, sapropelic prone hybrid, humic prone hybrid, humic and coal. It is shown that the hydrocarbon expulsion efficiency of sapropelic and sapropelic prone hybrid excellent source rocks is lower than 30% at the low-maturity stage, 30%–60% at the principal oil generation stage, and 50%–80% at the high-maturity stage, which are all about 10% higher than that of humic prone hybrid and humic source rocks at the corresponding stages. The resource distribution and cracked gas expulsion of occluded hydrocarbon since the high-maturity stage of marine source rocks in the Sichuan Basin were preliminarily calculated on the basis of the evolution models. The cracked gas expulsion is 230.4 × 1012 m3 at the high evolution stage of occluded hydrocarbon of the Lower Cambrian Qiongzhusi Fm in this basin, and 12.3 × 1012 m3 from the source rocks of Sinian Doushantuo Fm, indicating good potential for natural gas resources. It is indicated that the favorable areas of occluded hydrocarbon cracked gas in the Qiongzhusi Fm source rocks in the Sichuan Basin include Gaoshiti–Moxi, Ziyang and Weiyuan, covering a favorable area of 4.3 × 104 km2.

  5. Hydrocarbon occurrence in NW Africa's MSGBC area

    Energy Technology Data Exchange (ETDEWEB)

    Reymond, A.; Negroni, P.

    1989-06-01

    The MSGBC (Mauritania, Senegal, The Gambia, Guinea-Bissau, Guinea Conakry) coastal basin has evolved as a passive margin from Jurassic time up to the present following a period of poorly known rifting of Permian to Middle Jurassic age. Structural configuration of the Paleozoic series is documented by large outcrops and a good number of seismic sections. Based on previous exploration efforts that found significant hydrocarbon shows, a comprehensive study of this African basin's source rocks, maturation evolution and petroleum generation potential was undertaken. About 1,000 geochemical analyses of the Paleozoic, Cretaceous and Tertiary series identified good source rocks in the Cenomano-Turonian, Silurian, Senonian and Paleocene ages. The parameters used to identify and characterize source rock are: Total organic carbon content (TOC) in percent and source potential (in kg HC/t), representing the amount of hydrocarbon generated per ton of rock and determined by Rock-Eval pyrolysis.

  6. Proceedings of the Hydrocarbons annual days - JAH 2012

    International Nuclear Information System (INIS)

    Brunck, Robert; Bouchard, Georges; Jones, Richard; Percebois, Jacques; Moncomble, Jean-Eudes; Barre, Bertrand; Duval, Valerie; Nauroy, Jean-Francois; Su, Kun; Borelli, Antoine; Daniel, Olivier; Bobrie, Xavier; Cambos, Philippe; Foussard, Christian; Despeche, Jean-Michel; Sigonney, Pierre; Vially, Roland; Bosseboeuf, Didier; Chateau, Bertrand; Pelcot, Julien; Aulnoit, Thierry de l'; Pinchon, Philippe; Karnik, Jean-Luc; Josse, Philippe; Bouteca, Maurice; Argillier, Jean-Francois; Durieux, Jean-Yves; Josseron, Eric; Zaitoun, Alain; Alazard Toux, Nathalie; Lacoin, Geoffroy; Marcus, Philippe; Malcor, Jean-Georges; Bales, Vincent; Appert, Olivier; Le Cuziat, Jean-Yves; Peyrat, Olivier; Fort, Joel; Fallouey, Patrick; Contie, Michel; Heurtier, Jean-Michel; Bouchard, Alban; Hazel, Terence; Baylocq, Pascal; Saincry, Daniel; Laparra, Thibault; Burban, Bruno; Poyet, Jean-Pierre; Travers, Christine; Foussard, Christian; Collieux, Regis; Schilansky, Jean-Louis; Nusbaumer, Bertrand; Muller, Isabelle; Lefebvre, Francois; Jullian, Sophie; Blez, Bernard

    2012-01-01

    This document gathers Power Point presentations proposed during plenary sessions and workshops. Plenary sessions addressed the relationship between hydrocarbons and new energy balances, the attractiveness of oil industry for students, operators operating in France, perspectives for the refining activity in Europe, the evolution of French system for research and innovation. The workshop topics have been: Gas, renewable and nuclear as the winning trio for 2050, Geomechanics for a better production, Economic intelligence, Ships for offshore service, Safety in the oil industry, Peak oil or peak demand, A know-how at the service of sea energies, Education in oil producing countries, Water treatment in hydrocarbon industries, Re-development of mature fields, Standards as an unavoidable tool for the international development, Future underwater fields, Technological challenges, environmental impact and safety for deep sea and ground-based drillings, Refining development and project financing

  7. IMPLICATIONS OF MICROBIAL ADHESION TO HYDROCARBONS FOR EVALUATING CELL-SURFACE HYDROPHOBICITY .1. ZETA-POTENTIALS OF HYDROCARBON DROPLETS

    NARCIS (Netherlands)

    BUSSCHER, HJ; VANDEBELTGRITTER, B; VANDERMEI, HC

    1995-01-01

    Microbial adhesion to hydrocarbons (MATH) is generally considered to be a measure of the organisms cell surface hydrophobicity. As microbial adhesion is a complicated interplay of long-range van der Waals and electrostatic forces and various short-range interactions, the above statement only holds

  8. Thermal mud maturation: organic matter and biological activity.

    Science.gov (United States)

    Centini, M; Tredici, M R; Biondi, N; Buonocore, A; Maffei Facino, R; Anselmi, C

    2015-06-01

    Many of the therapeutic and cosmetic treatments offered in spas are centred on mud therapy, to moisturize the skin and prevent skin ageing and rheumatic diseases. Thermal mud is a complex matrix composed of organic and inorganic elements which contribute to its functions. It is a natural product derived from the long mixing of clay and thermal water. During its maturation, organic substances are provided by the microalgae, which develop characteristic of the composition of thermal water. The aim of this study was to identify methods for introducing objective parameters as a basis for characterizing thermal mud and assessing its efficacy. Samples of thermal mud were collected at the Saturnia spa, where there are several sulphureous pools. The maturation of the mud was evaluated by organic component determination using extractive methods and chromatographic analysis (HPLC, GC-MS, SPME). We also studied the radical scavenging activity of mud samples at different stages of maturation, in a homogeneous phase, using several tests (DPPH, ORAC, ABTS). We identified several classes of compounds: saturated and unsaturated fatty acids, hydroxyl acids, dicarboxylic acids, ketoacids, alcohols and others. SPME analysis showed the presence of various hydrocarbons compounds (C(11) -C(17)) and long-chain alcohols (C(12) -C(16)). Six or seven months seemed appropriate to complete the process of maturation, and the main effect of maturation time was the increase of lipids. Six-month mud showed the highest activity. The hydrophilic extract was more active than the lipophilic extract. The results indicate that maturation of thermal mud can be followed on the basis of the changes in its organic composition and antioxidant properties along the time. They also highlight the need to develop reference standards for thermal muds in relation to assess their use for therapeutic and cosmetic purposes. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  9. Total Petroleum Hydrocarbon Criteria Working Group (TPHCWG) Field Demonstration Report: IRP Site 4, POL Area, Springfield ANG Base, Springfield, Ohio

    National Research Council Canada - National Science Library

    Reed, Dennis

    2003-01-01

    ...) methodology to compare the approaches. Soil core composites were analyzed for trichloroethylene, gasoline-range organics, volatile petroleum hydrocarbons, benzene, toluene, ethylbenzene, and xylenes...

  10. A Thermal Maturity Analysis of the Effective Cretaceous Petroleum System in the Southern Persian Gulf Basin

    Directory of Open Access Journals (Sweden)

    Majid Alipour

    2017-10-01

    Full Text Available Commercial hydrocarbon discoveries in the Cretaceous of the southern Persian Gulf basin provide direct evidence that there is an effective petroleum system associated with the Cretaceous series. The revised models of thermal maturity in this region are needed to investigate lateral and stratigraphic variations of thermal maturity, which have not so far been addressed in detail for this part of the Persian Gulf. Such thermal maturity models are required to delineate the existing play assessment risks and to predict properties in more deeply buried undrilled sections. This study uses two dimensional basin modeling techniques to reconstruct maturity evolution of the Cenomanian Middle Sarvak source rock, presumably the most likely source for these hydrocarbons. The results indicate that an estimated 900 meter difference in the depth of burial between the southeastern high and the adjacent trough tends to be translated into noticeable variations at both temperature (135 °C versus 162 °C and vitrinite reflectance (0.91% versus 1.35%. Since the organic matter in the mentioned source rock is of reactive type II, these could cause a shift of about 18 million years in the onset of hydrocarbon generation over respective areas.

  11. High Pressure Preignition Chemistry of Hydrocarbons and Hydrocarbon Mixtures

    National Research Council Canada - National Science Library

    Cernansky, N.P

    1998-01-01

    .... The research program entailed mechanistic studies examining the oxidation chemistry of single-component hydrocarbons and ignition studies examining the overall ignition of pure single component fuels and fuel blends...

  12. ASSOCIATION BETWEEN DENTAL AND SKELETAL MATURATION STAGES IN CROATIAN SUBJECTS.

    Science.gov (United States)

    Srkoc, Tamara; Mestrović, Senka; Anić-Milosević, Sandra; Slaj, Mladen

    2015-12-01

    This study investigated the relationships between the stages of calcification of teeth and cervical vertebral maturation. The sample consisted of 295 subjects (129 male and 166 female), mean age 13.36 ± 2.65 (range 7-18) years. Dental age was evaluated from panoramic radiographs according to the method of Demirjian. Cervical vertebral maturation was determined on lateral cephalometric radiographs using cervical vertebrae maturation stages (CVS). For assessing the relationship between cervical vertebral and dental maturation, percentage distributions of the stages of calcification for each studied tooth were calculated. Only in the first CVS stage, boys and girls were of the same age. In all other stages (CVS 2-CVS 6) girls were by 0.98 (range 0.23-1.86) younger than boys. Gender differences in the mineralization pattern were also observed. It was found that dental maturation was finished earlier in female subjects. The highest correlation coefficient between dental and skeletal maturity was found for second premolars. Mineralization pattern of second premolars could be considered as a guideline for prediction of the pubertal growth spurt. Dental maturation stages might be clinically useful as a reliable indicator of facial growth.

  13. Identifying future directions for subsurface hydrocarbon migration research

    Science.gov (United States)

    Leifer, I.; Clark, J. F.; Luyendyk, B.; Valentine, D.

    Subsurface hydrocarbon migration is important for understanding the input and impacts of natural hydrocarbon seepage on the environment. Great uncertainties remain in most aspects of hydrocarbon migration, including some basic mechanisms of this four-phase flow of tar, oil, water, and gas through the complex fracture-network geometry particularly since the phases span a wide range of properties. Academic, government, and industry representatives recently attended a workshop to identify the areas of greatest need for future research in shallow hydrocarbon migration.Novel approaches such as studying temporal and spatial seepage variations and analogous geofluid systems (e.g., geysers and trickle beds) allow deductions of subsurface processes and structures that remain largely unclear. Unique complexities exist in hydrocarbon migration due to its multiphase flow and complex geometry, including in-situ biological weathering. Furthermore, many aspects of the role of hydrocarbons (positive and negative) in the environment are poorly understood, including how they enter the food chain (respiration, consumption, etc.) and “percolate” to higher trophic levels. But understanding these ecological impacts requires knowledge of the emissions' temporal and spatial variability and trajectories.

  14. Growth of hydrocarbon utilizing microorganisms

    Digital Repository Service at National Institute of Oceanography (India)

    Bhosle, N.B.; Mavinkurve, S.

    Two isolates from marine mud having broad spectrum hydrocarbon utilizing profile were identified as Arthrobacter simplex and Candida tropicalis.Both the organisms grew exponentially on crude oil. The cell yield of the organisms was influenced...

  15. Process for treating hydrocarbons, etc

    Energy Technology Data Exchange (ETDEWEB)

    1933-09-15

    A process is described for treating simultaneously bituminous substances and hydrocarbon oils for the production of low-boiling hydrocarbons and volatilization of the bituminous substances, characterized by the fact that it consists of heating a current of charge constituted by a mixture of the bituminous substances and hydrocarbon oils, to a high temperature, passing the heated current into a zone of extended reaction where the vapors are separated from the liquid or solid residue to favor transformation of the liquid hydrocarbons and volatilization of the bituminous substances, owing to the utilization of a heating agent carried to a high temperature being brought in contact with the heated charge in order to communicate its heat to the charge, while this later presents itself as relatively fine pellet or in the condition of distinct particles, particularly separated from one another.

  16. Ossification score is a better indicator of maturity related changes in eating quality than animal age.

    Science.gov (United States)

    Bonny, S P F; Pethick, D W; Legrand, I; Wierzbicki, J; Allen, P; Farmer, L J; Polkinghorne, R J; Hocquette, J-F; Gardner, G E

    2016-04-01

    Ossification score and animal age are both used as proxies for maturity-related collagen crosslinking and consequently decreases in beef tenderness. Ossification score is strongly influenced by the hormonal status of the animal and may therefore better reflect physiological maturity and consequently eating quality. As part of a broader cross-European study, local consumers scored 18 different muscle types cooked in three ways from 482 carcasses with ages ranging from 590 to 6135 days and ossification scores ranging from 110 to 590. The data were studied across three different maturity ranges; the complete range of maturities, a lesser range and a more mature range. The lesser maturity group consisted of carcasses having either an ossification score of 200 or less or an age of 987 days or less with the remainder in the greater maturity group. The three different maturity ranges were analysed separately with a linear mixed effects model. Across all the data, and for the greater maturity group, animal age had a greater magnitude of effect on eating quality than ossification score. This is likely due to a loss of sensitivity in mature carcasses where ossification approached and even reached the maximum value. In contrast, age had no relationship with eating quality for the lesser maturity group, leaving ossification score as the more appropriate measure. Therefore ossification score is more appropriate for most commercial beef carcasses, however it is inadequate for carcasses with greater maturity such as cull cows. Both measures may therefore be required in models to predict eating quality over populations with a wide range in maturity.

  17. Slab replacement maturity guidelines : [summary].

    Science.gov (United States)

    2014-04-01

    Concrete sets in hours at moderate temperatures, : but the bonds that make concrete strong continue : to mature over days to years. However, for : replacement concrete slabs on highways, it is : crucial that concrete develop enough strength : within ...

  18. SOUL System Maturation, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Busek Co. Inc. proposes to advance the maturity of an innovative Spacecraft on Umbilical Line (SOUL) System suitable for a wide variety of applications of interest...

  19. SOUL System Maturation, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Busek Co. Inc. proposes to advance the maturity of an innovative Spacecraft on Umbilical Line (SOUL) System suitable for a wide variety of applications of interest...

  20. Predicting hydrocarbon release from soil

    International Nuclear Information System (INIS)

    Poppendieck, D.; Loehr, R.C.

    2002-01-01

    'Full text:' The remediation of hazardous chemicals from soils can be a lengthy and costly process. As a result, recent regulatory initiatives have focused on risk-based corrective action (RBCA) approaches. Such approaches attempt to identify the amount of chemical that can be left at a site with contaminated soil and still be protective of human health and the environment. For hydrocarbons in soils to pose risk to human heath and the environment, the hydrocarbons must be released from the soil and accessible to microorganisms, earthworms, or other higher level organisms. The sorption of hydrocarbons to soil can reduce the availability of the hydrocarbon to receptors. Typically in soils and sediments, there is an initial fast release of a hydrocarbon from the soil to the aqueous phase followed by a slower release of the remaining hydrocarbon to the aqueous phase. The rate and extent of slow release can influence aqueous hydrocarbon concentrations and the fate and transport of hydrocarbons in the subsurface. Once the fast fraction of the chemical has been removed from the soil, the remaining fraction of a chemical may desorb at a rate that natural mechanisms can attenuate the released hydrocarbon. Hence, active remediation may be needed only until the fast fraction has been removed. However, the fast fraction is a soil and chemical specific parameter. This presentation will present a tier I type protocol that has been developed to quickly estimate the fraction of hydrocarbons that are readily released from the soil matrix to the aqueous phase. Previous research in our laboratory and elsewhere has used long-term desorption (four months) studies to determine the readily released fraction. This research shows that a single short-term (less than two weeks) batch extraction procedure provides a good estimate of the fast released fraction derived from long-term experiments. This procedure can be used as a tool to rapidly evaluate the release and bioavailability of

  1. Geochemical assessment of light gaseous hydrocarbons in near-surface soils of Kutch-Saurashtra: Implication for hydrocarbon prospects

    Science.gov (United States)

    Rao, P. Lakshmi Srinivasa; Madhavi, T.; Srinu, D.; Kalpana, M. S.; Patil, D. J.; Dayal, A. M.

    2013-02-01

    Light hydrocarbons in soil have been used as direct indicators in geochemical hydrocarbon exploration, which remains an unconventional path in the petroleum industry. The occurrence of adsorbed soil gases, methane and heavier homologues were recorded in the near-surface soil samples collected from Kutch-Saurashtra, India. Soil gas alkanes were interpreted to be derived from deep-seated hydrocarbon sources and have migrated to the surface through structural discontinuities. The source of hydrocarbons is assessed to be thermogenic and could have been primarily derived from humic organic matter with partial contribution from sapropelic matter. Gas chromatographic analyses of hydrocarbons desorbed from soil samples through acid extraction technique showed the presence of methane through n-butane and the observed concentrations (in ppb) vary from: methane (C1) from 4-291, ethane (C2) from 0-84, propane (C3) from 0-37, i-butane (iC4) from 0-5 and n-butane (nC4) from 0-4. Carbon isotopes measured for methane and ethane by GC-C-IRMS, range between -42.9‰ to -13.3‰ (Pee Dee Belemnite - PDB) and -21.2‰ to -12.4‰ (PDB), respectively. The increased occurrence of hydrocarbons in the areas near Anjar of Kutch and the area south to Rajkot of Saurashtra signifies the area potential for oil and gas.

  2. Correlation Between Dental and Cervical Vertebral Maturation in Iranian Females

    OpenAIRE

    Valizadeh, Solmaz; Eil, Nakissa; Ehsani, Sara; Bakhshandeh, Hooman

    2012-01-01

    Background Considerable variations in the development stage among patients of the same chronological age have led to introduce the concept of the developmental age based on the maturation of different organs such as cervical vertebrae or teeth. Objectives The purpose of this study was to investigate the correlation between the stages of tooth calcification and the cervical vertebral maturation in Iranian females. Patients and Methods Four hundred females (age range, 8 to 14 years) participate...

  3. Hydrocarbon removal with constructed wetlands

    OpenAIRE

    Eke, Paul Emeka

    2008-01-01

    Wetlands have long played a significant role as natural purification systems, and have been effectively used to treat domestic, agricultural and industrial wastewater. However, very little is known about the biochemical processes involved, and the use of constructed treatment wetlands in the removal of petroleum aromatic hydrocarbons from produced and/or processed water. Wastewaters from the oil industry contain aromatic hydrocarbons such as benzene, toluene, ethylbenzene and x...

  4. Bioassay of polycyclic aromatic hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Van Kirk, E.A.

    1980-08-01

    A positive relationship was found between the photodynamic activity of 24 polycyclic aromatic hydrocarbons versus published results on the mutagenicity, carcinogenicity, and initiation of unscheduled DNA synthesis. Metabolic activation of benzo(a)pyrene resulted in detection of increased mutagenesis in Paramecium tetraurelia as found also in the Ames Salmonella assay. The utility of P. tetraurelia as a biological detector of hazardous polycyclic aromatic hydrocarbons is discussed.

  5. Naturally Engineered Maturation of Cardiomyocytes

    Directory of Open Access Journals (Sweden)

    Gaetano J. Scuderi

    2017-05-01

    Full Text Available Ischemic heart disease remains one of the most prominent causes of mortalities worldwide with heart transplantation being the gold-standard treatment option. However, due to the major limitations associated with heart transplants, such as an inadequate supply and heart rejection, there remains a significant clinical need for a viable cardiac regenerative therapy to restore native myocardial function. Over the course of the previous several decades, researchers have made prominent advances in the field of cardiac regeneration with the creation of in vitro human pluripotent stem cell-derived cardiomyocyte tissue engineered constructs. However, these engineered constructs exhibit a functionally immature, disorganized, fetal-like phenotype that is not equivalent physiologically to native adult cardiac tissue. Due to this major limitation, many recent studies have investigated approaches to improve pluripotent stem cell-derived cardiomyocyte maturation to close this large functionality gap between engineered and native cardiac tissue. This review integrates the natural developmental mechanisms of cardiomyocyte structural and functional maturation. The variety of ways researchers have attempted to improve cardiomyocyte maturation in vitro by mimicking natural development, known as natural engineering, is readily discussed. The main focus of this review involves the synergistic role of electrical and mechanical stimulation, extracellular matrix interactions, and non-cardiomyocyte interactions in facilitating cardiomyocyte maturation. Overall, even with these current natural engineering approaches, pluripotent stem cell-derived cardiomyocytes within three-dimensional engineered heart tissue still remain mostly within the early to late fetal stages of cardiomyocyte maturity. Therefore, although the end goal is to achieve adult phenotypic maturity, more emphasis must be placed on elucidating how the in vivo fetal microenvironment drives cardiomyocyte

  6. Maturation of sugar maple seed

    Science.gov (United States)

    Clayton M., Jr. Carl; Albert G., Jr. Snow; Albert G. Snow

    1971-01-01

    The seeds of a sugar maple tree (Acer saccharum Marsh.) do not mature at the same time every year. And different trees mature their seeds at different times. So time of year is not a reliable measure of when seeds are ripe. Better criteria are needed. In recent studies we have found that moisture content and color are the best criteria for judging when sugar maple...

  7. Electrostatically atomised hydrocarbon sprays

    Energy Technology Data Exchange (ETDEWEB)

    Yule, A.J.; Shrimpton, J.S.; Watkins, A.P.; Balachandran, W.; Hu, D. [UMIST, Manchester (United Kingdom). Thermofluids Division, Dept. of Mechanical Engineering

    1995-07-01

    A burner using an electrostatic method to produce and control a fuel spray is investigated for non-burning sprays. The burner has a charge injection nozzle and the liquid flow rate and charge injection rate are varied using hydrocarbon liquids of differing viscosities, surface tensions and electrical conductivities (kerosene, white spirit and diesel oil). Droplet size distributions are measured and it is shown how the dropsize, spray pattern, breakup mechanism and breakup length depend on the above variables, and in particular on the specific charge achieved in the spray. The data are valuable for validating two computer models under development. One predicts the electric field and flow field inside the nozzle as a function of emitter potential, geometry and flow rate. The other predicts the effect of charge on spray dispersion, with a view to optimizing spray combustion. It is shown that electrostatic disruptive forces can be used to atomize oils at flow rates commensurate with practical combustion systems and that the charge injection technique is particularly suitable for highly resistive liquids. Possible limitations requiring further research include the need to control the wide spray angle, which may provide fuel-air mixtures too lean near the nozzle, and the need to design for maximum charge injection rate, which is thought to be limited by corona breakdown in the gas near the nozzle orifice. 30 refs., 15 figs., 1 tab.

  8. HYDROCARBONS RESERVES IN VENEZUELA

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez Cruz, D.J.

    2007-07-01

    Venezuela is an important player in the energy world, because of its hydrocarbons reserves. The process for calculating oil and associated gas reserves is described bearing in mind that 90% of the gas reserves of Venezuela are associated to oil. Likewise, an analysis is made of the oil reserves figures from 1975 to 2003. Reference is also made to inconsistencies found by international experts and the explanations offered in this respect by the Ministry of Energy and Petroleum (MENPET) and Petroleos de Venezuela (PDVSA) regarding the changes that took place in the 1980s. In turn, Hubbert's Law is explained to determine peak production of conventional oil that a reservoir or field will reach, as well as its relationship with remaining reserves. Emphasis is placed on the interest of the United Nations on this topic. The reserves of associated gas are presented along with their relationship with the different crude oils that are produced and with injected gas, as well as with respect to the possible changes that would take place in the latter if oil reserves are revised. Some recommendations are submitted so that the MENPET starts preparing the pertinent policies ruling reserves. (auth)

  9. 40 CFR Table 2c to Subpart E of... - Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures 2C Table 2C to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Boiling range (degrees F) Criteria Reactivityfactor 21 280-290 Aromatic...

  10. A New Global Open Source Marine Hydrocarbon Emission Site Database

    Science.gov (United States)

    Onyia, E., Jr.; Wood, W. T.; Barnard, A.; Dada, T.; Qazzaz, M.; Lee, T. R.; Herrera, E.; Sager, W.

    2017-12-01

    Hydrocarbon emission sites (e.g. seeps) discharge large volumes of fluids and gases into the oceans that are not only important for biogeochemical budgets, but also support abundant chemosynthetic communities. Documenting the locations of modern emissions is a first step towards understanding and monitoring how they affect the global state of the seafloor and oceans. Currently, no global open source (i.e. non-proprietry) detailed maps of emissions sites are available. As a solution, we have created a database that is housed within an Excel spreadsheet and use the latest versions of Earthpoint and Google Earth for position coordinate conversions and data mapping, respectively. To date, approximately 1,000 data points have been collected from referenceable sources across the globe, and we are continualy expanding the dataset. Due to the variety of spatial extents encountered, to identify each site we used two different methods: 1) point (x, y, z) locations for individual sites and; 2) delineation of areas where sites are clustered. Certain well-known areas, such as the Gulf of Mexico and the Mediterranean Sea, have a greater abundance of information; whereas significantly less information is available in other regions due to the absence of emission sites, lack of data, or because the existing data is proprietary. Although the geographical extent of the data is currently restricted to regions where the most data is publicly available, as the database matures, we expect to have more complete coverage of the world's oceans. This database is an information resource that consolidates and organizes the existing literature on hydrocarbons released into the marine environment, thereby providing a comprehensive reference for future work. We expect that the availability of seafloor hydrocarbon emission maps will benefit scientific understanding of hydrocarbon rich areas as well as potentially aiding hydrocarbon exploration and environmental impact assessements.

  11. Catalyst for reforming hydrocarbons with water vapors

    International Nuclear Information System (INIS)

    Nicklin, T.; Farrington, F.; Whittaker, J.R.

    1979-01-01

    The catalyst should reform hydrocarbons with water vapour. It consists of a carrier substance (preferably clay) on whose surface the catalytically active substances are formed. By impregnation one obtains this with a mixture of thermally destructable nickel and uranium compounds and calcination of the impregnated carrier. The catalyst is marked by a definite weight ratio of uranium to nickel (about 0.6 to 1), the addition of barium compounds and a maximum limit of these additives. All details of manufacture and the range of variations are described in detail. (UWI) [de

  12. Correlation between Dental Maturity by Demirjian Method and Skeletal Maturity by Cervical Vertebral Maturity Method using Panoramic Radiograph and Lateral Cephalogram

    Directory of Open Access Journals (Sweden)

    Madhusudhanan Mallika Mini

    2017-01-01

    Full Text Available Introduction: Radiographs are effective tools in assessing the stages of bone maturation in dentistry. The cervical vertebral maturation method is a proven effective tool in assessing the adolescent growth spurt than hand-wrist radiographs in an individual. Assessment of dental calcification stages are a reliable method for determining dental maturity. Panoramic imaging can be used as the primary imaging modality for assessing maturity if a correlation can be found out between tooth calcification stages and cervical vertebral maturation stages. This study was conducted to determine the correlation between dental maturity stage and cervical vertebral maturity stage and to estimate predictor variables for cervical vertebral maturation stages (CVMS stratified by gender in a tertiary hospital setting. Materials and Methods: A descriptive study was conducted among patients accessing orthodontic care in radiology outpatient clinic, Oral Medicine and Radiology department, Government Dental College Thiruvananthapuram for a period of 15 months. Participants were selected between the ages of 8 and 16 years. Panoramic radiographs and lateral cephalograms were used to determine dental maturity stages using Demirjian method and CVMS using Bacetti and Franchi method, respectively. Results: One hundred patients (males = 46, females = 54 were included in the study; the spearman rank order correlation revealed significant relationship. The correlation ranged from 0.61 to 0.74 for females and 0.48 to 0.51 for males. Second premolar showed highest correlation and canine the lowest for both females and males. Stage G of mandibular second premolar signifies the pubertal growth period in this study population. By ordinal regression model, G stage of second premolar was found to be a significant predictor in males and stage H followed by G and F in females for the age group of 12–14 years. Conclusion: Dental maturation stages were significantly correlated with CVMS

  13. Release of sulfur- and oxygen-bound components from a sulfur-rich kerogen during simulated maturation by hydrous pyrolysis

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Putchew, A.; Schaeffer-Reiss, C.; Schaeffer, P.; Koopmans, M.P.; Leeuw, J.W. de; Lewan, M.D.

    1998-01-01

    An immature sulfur-rich marl from the Gessosso-solfifera Formation of the Vena del Gesso Basin (Messinian, Italy) has been subjected to hydrous pyrolysis (160 to 330°C) to simulate maturation under natural conditions. The kerogen of the unheated and heated samples was isolated and the hydrocarbons

  14. Skeletal maturity assessment using mandibular canine calcification stages

    Directory of Open Access Journals (Sweden)

    Vildana Džemidžić

    2016-11-01

    Full Text Available Objective. The aims of this study were: to investigate the relationship between mandibular canine calcification stages and skeletal maturity; and to evaluate whether the mandibular canine calcification stages may be used as a reliable diagnostic tool for skeletal maturity assessment. Materials and methods. This study included 151 subjects: 81 females and 70 males, with ages ranging from 9 to 16 years (mean age: 12.29±1.86 years. The inclusion criteria for subjects were as follows: age between 9 and 16 years; good general health without any hormonal, nutritional, growth or dental development problems. Subjects who were undergoing or had previously received orthodontic treatment were not included in this study. The calcification stages of the left permanent mandibular canine were assessed according to the method of Demirjian, on panoramic radiographs. Assessment of skeletal maturity was carried out using the cervical vertebral maturation index (CVMI, as proposed by the Hassel-Farman method, on lateral cephalograms. The correlation between the calcification stages of mandibular canine and skeletal maturity was estimated separately for male and female subjects. Results. Correlation coefficients between calcification stages of mandibular canine and skeletal maturity were 0.895 for male and 0.701 for female subjects. Conclusions. A significant correlation was found between the calcification stages of the mandibular canine and skeletal maturity. The calcification stages of the mandibular canine show a satisfactory diagnostic performance only for assessment of pre-pubertal growth phase.

  15. Underwater Ranging

    OpenAIRE

    S. P. Gaba

    1984-01-01

    The paper deals with underwater laser ranging system, its principle of operation and maximum depth capability. The sources of external noise and methods to improve signal-to-noise ratio are also discussed.

  16. Sustaining Exploration in Mature Basins

    International Nuclear Information System (INIS)

    Bayo, A.

    2002-01-01

    Exploration is a business like any other business driven by opportunity, resources and expectation of profit. Therefore, exploration will thrive anywhere the opportunities are significant, the resources are available and the outlook for profit (or value creation) is good. To sustain exploration activities anywhere, irrespective of the environment, there must be good understanding of the drivers of these key investment criteria. This paper will examine these investment criteria as they relate to exploration business and address the peculiarity of exploration in mature basin. Mature basins are unique environment that lends themselves a mix of fears, paradigms and realities, particularly with respect to the perception of value. To sustain exploration activities in a mature basin, we need to understand these perceptions relative to the true drivers of profitability. Exploration in the mature basins can be as profitable as exploration in emerging basins if the dynamics of value definition-strategic and fiscal values are understood by operators, regulators and co ventures alike. Some suggestions are made in this presentation on what needs to be done in addressing these dynamic investment parameters and sustaining exploration activities in mature basins

  17. Microbial Degradation of Polycyclic Aromatic Hydrocarbons and Characterization of Bacteria

    Science.gov (United States)

    Tikilili, P. V.; Chirwa, E. M. N.

    2010-01-01

    Biodegradation of polycyclic aromatic hydrocarbons was studied. Naphthalene was used as a model compound to represent these compounds. Low initial concentrations of naphthalene in a range of 30-60 mg/L were completely degraded after incubation for 15 hrs by consortia from a landfill soil while consortia from minewater took more that 29 hrs to reach complete degradation.

  18. Adsorption of volatile hydrocarbons in iron polysulfide chalcogels

    KAUST Repository

    Ahmed, Ejaz; Rothenberger, Alexander

    2014-01-01

    are found in micro (below 2 nm), meso (2-50 nm), and macro (above 50 nm) porous regions. These chalcogels possess optical bandgaps in the range of 1.55-2.70 eV. These aerogels have been studied for the adsorption of volatile hydrocarbons and gases. A much

  19. Syntrophic biodegradation of hydrocarbon contaminants.

    Science.gov (United States)

    Gieg, Lisa M; Fowler, S Jane; Berdugo-Clavijo, Carolina

    2014-06-01

    Anaerobic environments are crucial to global carbon cycling wherein the microbial metabolism of organic matter occurs under a variety of redox conditions. In many anaerobic ecosystems, syntrophy plays a key role wherein microbial species must cooperate, essentially as a single catalytic unit, to metabolize substrates in a mutually beneficial manner. Hydrocarbon-contaminated environments such as groundwater aquifers are typically anaerobic, and often methanogenic. Syntrophic processes are needed to biodegrade hydrocarbons to methane, and recent studies suggest that syntrophic hydrocarbon metabolism can also occur in the presence of electron acceptors. The elucidation of key features of syntrophic processes in defined co-cultures has benefited greatly from advances in 'omics' based tools. Such tools, along with approaches like stable isotope probing, are now being used to monitor carbon flow within an increasing number of hydrocarbon-degrading consortia to pinpoint the key microbial players involved in the degradative pathways. The metagenomic sequencing of hydrocarbon-utilizing consortia should help to further identify key syntrophic features and define microbial interactions in these complex communities. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. Remediation of hydrocarbons in crude oil-contaminated soils using Fenton's reagent.

    Science.gov (United States)

    Ojinnaka, Chukwunonye; Osuji, Leo; Achugasim, Ozioma

    2012-11-01

    Sandy soil samples spiked with Bonny light crude oil were subsequently treated with Fenton's reagent at acidic, neutral, and basic pH ranges. Oil extracts from these samples including an untreated one were analyzed 1 week later with a gas chromatograph to provide evidence of hydrocarbon depletion by the oxidant. The reduction of three broad hydrocarbon groups-total petroleum hydrocarbon (TPH); benzene, toluene, ethylbenzene, and xylene (BTEX); and polycyclic aromatic hydrocarbon (PAH) were investigated at various pHs. Hydrocarbon removal was efficient, with treatment at the acidic pH giving the highest removal of about 96% for PAH, 99% for BTEX, and some TPH components experiencing complete disappearance. The four-ringed PAHs were depleted more than their three-ringed counterparts at the studied pH ranges.

  1. Production of light hydrocarbons, etc. [from heavy hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    1937-10-07

    A process is given for the production of light hydrocarbons of the gasoline type and, if desired, of the middle-oil type, from liquid or fusible heavy or medium heavy hydrocarbon materials. The process comprises subjecting the said initial materials in the first stage to catalytic hydrofining, separating the lower boiling constituents and the hydrogenating gas from the resulting products and then subjecting the higher boiling constituents in a second stage to a splitting destructive hydrogenation and then recycling substantially the entire reaction mixture obtained in the second stage to the frst stage.

  2. Distribution and geochemical application of aromatic hydrocarbons in crude oils

    International Nuclear Information System (INIS)

    Asif, M.; Tahira, F.

    2007-01-01

    Distribution of aromatic hydrocarbons was studied in a set of crude oils, five from northern Indus basin of potwar area and two from southern Indus basin. Diaromatic and triaromatic hydrocarbons were separated from highly complex mixture of sedimentary organic matter by using liquid chromatography techniques such as column chromatography, TLC and GC-FID. These classes of compounds were identified to alkylated isomers of naphthalenes and phenanthrenes by using reference chromatograms and literature data. High concentration of di-,tri- and tetra-methyl naphthalenes was observed in all crude oils except Kal. The relative increase in concentration of alkyl naphthalenes was found as moved to higher methyl substituted isomers. This suggests that they are the product of sedimentary alkylation reactions during catagensis and metagensis. The significant concentration of methyl phenanthrenes indicated source of organic matter. High levels of both 1-MP and 9-MP showed marine and terrestrial source of organic matter except Umer crude oil which is most likely to have terrestrial origin. The ratios of beta-substituted to the alpha-substituted isomers of both alkyl naphthalenes and alkyl phenanthrene were used to assess the thermal maturity of sedimentary organic matter, which revealed high maturity level of Dhurnal, Pindori, Badin and Toot crude oils. (author)

  3. Public Sector IS Maturity Models

    DEFF Research Database (Denmark)

    Zinner Henriksen, Helle; Andersen, Kim Normann; Medaglia, Rony

    2011-01-01

    Online applications and processing of tax forms, driver licenses, and construction permits are examples of where policy attention and research have been united in efforts aiming to categorize the maturity level of e-services. Less attention has been attributed to policy areas with continuous online...... citizenpublic interaction, such as in public education. In this paper we use a revised version of the Public Sector Process Rebuilding (PPR) maturity model for mapping 200 websites of public primary schools in Denmark. Findings reveal a much less favorable picture of the digitization of the Danish public sector...... compared to the high ranking it has received in the international benchmark studies. This paper aims at closing the gap between the predominant scope of maturity models and the frequency of citizen-public sector interaction, and calls for increased attention to the activities of government where the scale...

  4. Chemical fingerprinting of hydrocarbon-contamination in soil.

    Science.gov (United States)

    Boll, Esther S; Nejrup, Jens; Jensen, Julie K; Christensen, Jan H

    2015-03-01

    Chemical fingerprinting analyses of 29 hydrocarbon-contaminated soils were performed to assess the soil quality and determine the main contaminant sources. The results were compared to an assessment based on concentrations of the 16 priority polycyclic aromatic hydrocarbons pointed out by the U.S. Environmental Protection Agency (EPAPAH16) and total petroleum hydrocarbon (TPH). The chemical fingerprinting strategy proposed in this study included four tiers: (i) qualitative analysis of GC-FID chromatograms, (ii) comparison of the chemical composition of both un-substituted and alkyl-substituted polycyclic aromatic compounds (PACs), (iii) diagnostic ratios of selected PACs, and (iv) multivariate data analysis of sum-normalized PAC concentrations. The assessment criteria included quantitative analysis of 19 PACs and C1-C4 alkyl-substituted homologues of naphthalene, fluorene, dibenzothiophene, phenanthrene, pyrene, and chrysene; and 13 oxygenated polycyclic aromatic compounds (O-PACs). The chemical composition of un-substituted and alkyl-substituted PACs and visual interpretation of GC-FID chromatograms were in combination successful in differentiating pyrogenic and petrogenic hydrocarbon sources and in assessing weathering trends of hydrocarbon contamination in the soils. Multivariate data analysis of sum-normalized concentrations could as a stand-alone tool distinguish between hydrocarbon sources of petrogenic and pyrogenic origin, differentiate within petrogenic sources, and detect weathering trends. Diagnostic ratios of PACs were not successful for source identification of the heavily weathered hydrocarbon sources in the soils. The fingerprinting of contaminated soils revealed an underestimation of PACs in petrogenic contaminated soils when the assessment was based solely on EPAPAH16. As alkyl-substituted PACs are dominant in petrogenic sources, the evaluation of the total load of PACs based on EPAPAH16 was not representative. Likewise, the O-PACs are not

  5. Bicarbonate Transport During Enamel Maturation.

    Science.gov (United States)

    Yin, Kaifeng; Paine, Michael L

    2017-11-01

    Amelogenesis (tooth enamel formation) is a biomineralization process consisting primarily of two stages (secretory stage and maturation stage) with unique features. During the secretory stage, the inner epithelium of the enamel organ (i.e., the ameloblast cells) synthesizes and secretes enamel matrix proteins (EMPs) into the enamel space. The protein-rich enamel matrix forms a highly organized architecture in a pH-neutral microenvironment. As amelogenesis transitions to maturation stage, EMPs are degraded and internalized by ameloblasts through endosomal-lysosomal pathways. Enamel crystallite formation is initiated early in the secretory stage, however, during maturation stage the more rapid deposition of calcium and phosphate into the enamel space results in a rapid expansion of crystallite length and mineral volume. During maturation-stage amelogenesis, the pH value of enamel varies considerably from slightly above neutral to acidic. Extracellular acid-base balance during enamel maturation is tightly controlled by ameloblast-mediated regulatory networks, which include significant synthesis and movement of bicarbonate ions from both the enamel papillary layer cells and ameloblasts. In this review we summarize the carbonic anhydrases and the carbonate transporters/exchangers involved in pH regulation in maturation-stage amelogenesis. Proteins that have been shown to be instrumental in this process include CA2, CA6, CFTR, AE2, NBCe1, SLC26A1/SAT1, SLC26A3/DRA, SLC26A4/PDS, SLC26A6/PAT1, and SLC26A7/SUT2. In addition, we discuss the association of miRNA regulation with bicarbonate transport in tooth enamel formation.

  6. Production of hydrocarbons, especially ethylene

    Energy Technology Data Exchange (ETDEWEB)

    1952-01-17

    The invention has for its object a process for the production of gaseous nonsaturated hydrocarbons, particularly ethylene and aromatic hydrocarbons, by starting with hydrocarbon oils entirely of paraffinic nature or their fractions, which consists in putting the separated products in contact with solid inert material especially with porous nonmetallic inert material or of heavy metals or their alloys, maybe in a finely divided state or in the form, of pieces or chips, at a temperature above 500/sup 0/C, or better between 600 and 700/sup 0/C at a velocity per hour of 0.6 to 3.0, and preferably 0.75 to 1.5 parts per volume of products per each part of space volume of catalyst.

  7. Enrichment of light hydrocarbon mixture

    Science.gov (United States)

    Yang,; Dali, [Los Alamos, NM; Devlin, David [Santa Fe, NM; Barbero, Robert S [Santa Cruz, NM; Carrera, Martin E [Naperville, IL; Colling, Craig W [Warrenville, IL

    2010-08-10

    Light hydrocarbon enrichment is accomplished using a vertically oriented distillation column having a plurality of vertically oriented, nonselective micro/mesoporous hollow fibers. Vapor having, for example, both propylene and propane is sent upward through the distillation column in between the hollow fibers. Vapor exits neat the top of the column and is condensed to form a liquid phase that is directed back downward through the lumen of the hollow fibers. As vapor continues to ascend and liquid continues to countercurrently descend, the liquid at the bottom of the column becomes enriched in a higher boiling point, light hydrocarbon (propane, for example) and the vapor at the top becomes enriched in a lower boiling point light hydrocarbon (propylene, for example). The hollow fiber becomes wetted with liquid during the process.

  8. Production of hydrocarbons of value

    Energy Technology Data Exchange (ETDEWEB)

    1931-06-16

    A process is described for the production of hydrocarbons of great value by treating with heat and pressure carbonaceous materials such as coals, tars, mineral oils, and products of distillation and transformation of these materials, also for the refining with heat and pressure of mixed liquid hydrocarbons by means of hydrogen gas, preferably in the presence of catalysts, consisting in using as the hydrogenating gas that obtained by gasification of combustible solids after partial or complete cleaning at atmospheric or elevated pressures, by means of solid adsorbents, chemical agents or catalysts, or mixtures of these agents, the hydrocarbons being characterized by strong unsaturation, and the presence of oxygen, sulfur compounds, and oxides of nitrogen.

  9. Process of distilling heavy hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    1929-12-03

    This invention has for its object the distillation of heavy liquid hydrocarbons for the purpose of obtaining lighter hydrocarbons stable and immediately salable for fuels in combustion motors. The process is distinguished by the fact that the heavy hydrocarbon is distilled by means of heating to a temperature in keeping with the nature of the material to be treated up to 350/sup 0/C under pressure or without pressure the distillation being carried out on catalysts containing successively nickel, copper, and iron (3 parts of nickel, 1 part of copper, and 1 part of iron), the vapors produced by this distillation being exposed in turn to the action of catalysts of the same nature and in the same proportion.

  10. Total organic carbon, an important tool in an holistic approach to hydrocarbon source fingerprinting

    Energy Technology Data Exchange (ETDEWEB)

    Boehm, P.D.; Burns, W.A.; Page, D.S.; Bence, A.E.; Mankiewicz, P.J.; Brown, J.S.; Douglas, G.S. [Battelle Member Inst., Waltham, MA (United States)

    2002-07-01

    The identification and allocation of multiple hydrocarbon sources in marine sediments is best achieved using an holistic approach. Total organic carbon (TOC) is one important tool that can constrain the contributions of specific sources and rule out incorrect source allocations in cases where inputs are dominated by fossil organic carbon. In a study of the benthic sediments from Prince William Sound (PWS) and the Gulf of Alaska (GOA), we find excellent agreement between measured TOC and TOC calculated from hydrocarbon fingerprint matches of polycyclic aromatic hydrocarbons (PAH) and chemical biomarkers. Confirmation by two such independent source indicators (TOC and fingerprint matches) provides evidence that source allocations determined by the fingerprint matches are robust and that the major TOC sources have been correctly identified. Fingerprint matches quantify the hydrocarbon contributions of various sources to the benthic sediments and the degree of hydrocarbon winnowing by waves and currents. TOC contents are then calculated using source allocation results from fingerprint matches and the TOCs of contributing sources. Comparisons of the actual sediment TOC values and those calculated from source allocation support our earlier published findings that the natural petrogenic hydrocarbon background in sediments in this area comes from eroding Tertiary shales and associated oil seeps along the northern GOA coast and exclude thermally mature area coals from being important contributors to the PWS background due to their high TOC content.

  11. Catalytic Upgrading of Sugars to Hydrocarbons Technology Pathway

    Energy Technology Data Exchange (ETDEWEB)

    Biddy, Mary J.; Jones, Susanne B.

    2013-03-31

    In support of the Bioenergy Technologies Office, the National Renewable Energy Laboratory (NREL) and the Pacific Northwest National Laboratory (PNNL) are undertaking studies of biomass conversion technologies to hydrocarbon fuels to identify barriers and target research toward reducing conversion costs. Process designs and preliminary economic estimates for each of these pathway cases were developed using rigorous modeling tools (Aspen Plus and Chemcad). These analyses incorporated the best information available at the time of development, including data from recent pilot and bench-scale demonstrations, collaborative industrial and academic partners, and published literature and patents. This technology pathway case investigates the catalytic conversion of solubilized carbohydrate streams to hydrocarbon biofuels, utilizing data from recent efforts within the National Advanced Biofuels Consortium (NABC) in collaboration with Virent, Inc.. Technical barriers and key research needs that should be pursued for the catalytic conversion of sugars pathway to be competitive with petroleum-derived gasoline, diesel and jet range hydrocarbon blendstocks have been identified.

  12. Structural Evolution of Kerogen and Bitumen during Thermal Maturation examined by Fourier-Transform Infrared Spectroscopy

    Science.gov (United States)

    Craddock, P. R.; Le Doan, T. V.; Pomerantz, A.

    2014-12-01

    Kerogen—the organic matter that is solid and insoluble in organic solvents—is a key component of organic-rich mudstones. The composition of kerogen affects the storage and transport of hydrocarbons in these unconventional resources and is known to change with thermal maturity. We report here using FTIR spectroscopy, the compositional characteristics of kerogen as a function of thermal maturity, together with the compositional characteristics of the organic phase, bitumen—the organic matter that is solid, but soluble in organic solvents. Kerogen is consumed during thermal maturation, whereas bitumen is an intermediary formed at low maturity from kerogen and consumed at higher maturities in formation of oil and gas. Bitumen relative to kerogen has higher aliphatic content, lower aromatic content, and lower abundance of oxygenated functions. At low maturity (vitrinite reflectance equivalent VRe ~ 0.5-0.9 %), the average length of aliphatic chains in bitumen increases during bitumen formation. At higher thermal maturities (VRe > 1.0-1.3 %), average aliphatic chain length decreases as bitumen is consumed. This evolution contrasts to that in kerogen, where aliphatic chain lengths shorten during all stages of maturation. Breakdown of kerogen appears to be driven by cleavage of oxygen functions at low maturity and removal of aliphatic carbons at higher maturities. These aliphatic-rich fragments may comprise the bitumen, and may in part explain the solubility of bitumen in organic solvents. Bitumen shows evidence of oxidation at low thermal maturity, a phenonemom not documented for kerogen. Bitumen maturation and degradation at higher thermal maturity is driven by cleavage and loss of aliphatic carbons, and is coincident with the maximum generation of oil and gas. The aromatic content of bitumen and of kerogen both increase during maturation as a consequence of the loss of aliphatic carbon. The oil and gas generation potential of the residual organic matter thus

  13. Method for upgrading diene-containing hydrocarbon mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Kidwell, L.E. Jr.; Holcomb, D.E.

    1984-05-22

    There is disclosed a method for upgrading of hydrocarbon mixtures, so as to reduce their content of gum precursors such as diolefins and pseudo-diolefins, and provide a resulting product mixture suitable for mild hydrogenation, for use as a motor fuel or as a feed stock to an extraction unit. The process comprises obtaining a hydrocarbon mixture containing about 60-90 wt. % of aromatic components, about 3-40 wt. % of dienes and pseudodienes, and monoolefins, and up to about 6 wt. % of relatively unreactive organic compounds, reacting this mixture with elemental sulfur in the approximate weight ratio of about 5-95 wt. % of the hydrocarbon mixture with about 95-5 wt. % of elemental sulfur, the reaction being carried out at a temperature in the range of 100/sup 0/-150/sup 0/ C. for about 10 minutes to 24 hours with good mixing, removing the unreacted materials by distillation and separating a sulfur-hydrocarbon reaction product to provide the upgraded hydrocarbon mixture.

  14. Biodegradation of aliphatic vs. aromatic hydrocarbons in fertilized arctic soils

    Science.gov (United States)

    Braddock, J.F.

    1999-01-01

    A study was carried out to test a simple bioremediation treatment strategy in the Arctic and analyze the influence of fertilization the degradation of aliphatic and aromatic hydrocarbons, e.g., pristine, n-tetradecane, n-pentadecane, 2-methylnaphthalene, naphthalene, and acenaphthalene. The site was a coarse sand pad that once supported fuel storage tanks. Diesel-range organics concentrations were 250-860 mg/kg soil at the beginning of the study. Replicate field plots treated with fertilizer yielded final concentrations of 0, 50, 100, or 200 mg N/kg soil. Soil pH and soil-water potentials decreased due to fertilizer application. The addition of fertilizer considerably increased soil respiration potentials, but not the populations of microorganisms measured. Fertilizer addition also led to ??? 50% loss of measured aliphatic and aromatic hydrocarbons in surface and subsurface soils. For fertilized plots, hydrocarbon loss was not associated with the quantity of fertilizer added. Losses of aliphatic hydrocarbons were ascribed to biotic processes, while losses of aromatic hydrocarbons were due to biotic and abiotic processes.

  15. Preparing valuable hydrocarbons by hydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Pier, M

    1930-08-22

    A process is described for the preparation of valuable hydrocarbons by treatment of carbonaceous materials, like coal, tars, minerals oils, and their distillation and conversion products, and for refining of liquid hydrocarbon mixture obtained at raised temperature and under pressure, preferably in the presence of catalysts, by the use of hydrogen-containing gases, purified and obtained by distilling solid combustibles, characterized by the purification of the hydrogen-containing gases being accomplished for the purpose of practically complete removal of the oxygen by heating at ordinary or higher pressure in the presence of a catalyst containing silver and oxides of metals of group VI of the periodic system.

  16. Purifying and regenerating hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    1931-11-19

    Hydrocarbons are freed from sulfur-containing compounds, colloidal asphaltic bodies and unstable unsaturated substances by treatment with a small amount of dilute sulfuric acid and a salt of a trivalent cation, such as ferric chloride or sulfate. Hydrocarbons specified are petroleum, crude benzol, low temperature tars, shale oil or vapor-phase cracked spirit. Motor spirit or lubricating oil distillates are refined and finally distilled. The acid reagent may be regenerated by filtering through sand or asbestos. Used lubricating oils may be treated similarly and after removal of refining agent, the oil is heated with an adsorbent and decolorizing material and then filtered.

  17. Hydrocarbons cocktails of the future

    International Nuclear Information System (INIS)

    Anon.

    2004-01-01

    This publication of the Areva Group, a world nuclear industry leader, provides information on the energy in many domains. This issue deals with the CO 2 pollution exchange, the carbon sinks to compensate the CO 2 , the green coal as an innovative solution, an outsize dam in China, the solar energy progresses in France and the french medicine academy in favor of Nuclear. A special chapter is devoted to the hydrocarbons of the future, artificial chemical combination created from constituents of hydrocarbons and derived from various sources. (A.L.B.)

  18. Mineral oil and synthetic hydrocarbons in cosmetic lip products.

    Science.gov (United States)

    Niederer, M; Stebler, T; Grob, K

    2016-04-01

    Lipsticks and lip care products may contain saturated hydrocarbons which either stem from mineral oil saturated hydrocarbons (MOSH) or are synthetic, that is polyolefin oligomeric saturated hydrocarbons (POSH). Some of these hydrocarbons are strongly accumulated and form granulomas in human tissues, which prompted Cosmetics Europe (former Colipa) to issue a recommendation for their use in lip care and oral products. From 2012 to 2014, MOSH+POSH were determined in 175 cosmetic lip products taken from the Swiss market in order to estimate their contribution to human exposure. Mineral oil saturated hydrocarbons and POSH were extracted and analysed by GC with FID. Areas were integrated as a total as well as by mass ranges with cuts at n-C25 and n-C34 to characterize the molecular mass distribution. About 68% of the products contained at least 5% MOSH+POSH (total concentration). For regular users, these products would be major contributors to their MOSH+POSH exposure. About 31% of the products contained more than 32% MOSH+POSH. Their regular usage would amount in an estimated MOSH+POSH exposure exceeding the highest estimated dietary exposure. The majority of the products contained hydrocarbons with a molecular mass range which was not in line with the recommendations of Cosmetics Europe. Taking into account that material applied to the lips largely ends up being ingested, MOSH and POSH levels should be reduced in the majority of cosmetic lip products. As the extensive evaluation of the data available on MOSH (EFSA J., 10, 2012, 2704) did not enable the specification of limits considered as safe, the present level of dietary exposure and its evaluation as 'of potential concern' provide the relevant bench mark, which means that lip products should contain clearly less than 5% MOSH+POSH. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  19. Motivational Maturity and Helping Behavior

    Science.gov (United States)

    Haymes, Michael; Green, Logan

    1977-01-01

    Maturity in conative development (type of motivation included in Maslow's needs hierarchy) was found to be predictive of helping behavior in middle class white male college students. The effects of safety and esteem needs were compared, and the acceptance of responsibility was also investigated. (GDC)

  20. Regulators of growth plate maturation

    NARCIS (Netherlands)

    Emons, Joyce Adriana Mathilde

    2010-01-01

    Estrogen is known to play an important role in longitudinal bone growth and growth plate maturation, but the mechanism by which estrogens exert their effect is not fully understood. In this thesis this role is further explored. Chapter 1 contains a general introduction to longitudinal bone growth

  1. Canadian hydrocarbon transportation system : transportation assessment

    International Nuclear Information System (INIS)

    2006-06-01

    This document provided an assessment of the Canadian hydrocarbon transportation system. In addition to regulating the construction and operation of Canada's 45,000 km of pipeline that cross international and provincial borders, Canada's National Energy Board (NEB) regulates the trade of natural gas, oil and natural gas liquids. The ability of pipelines to delivery this energy is critical to the country's economic prosperity. The pipeline system includes large-diameter, cross-country, high-pressure natural gas pipelines, low-pressure crude oil and oil products pipelines and small-diameter pipelines. In order to assess the hydrocarbon transportation system, staff at the NEB collected data from pipeline companies and a range of publicly available sources. The Board also held discussions with members of the investment community regarding capital markets and emerging issues. The assessment focused largely on evaluating whether Canadians benefit from an efficient energy infrastructure and markets. The safety and environmental integrity of the pipeline system was also evaluated. The current adequacy of pipeline capacity was assessed based on price differentials compared with firm service tolls for major transportation paths; capacity utilization on pipelines; and, the degree of apportionment on major oil pipelines. The NEB concluded that the Canadian hydrocarbon transportation system is working effectively, with an adequate capacity in place on existing natural gas pipelines, but with a tight capacity on oil pipelines. It was noted that shippers continue to indicate that they are reasonably satisfied with the services provided by pipeline companies and that the NEB-regulated pipeline companies are financially stable. 14 refs, 11 tabs., 28 figs., 4 appendices

  2. Biodegrader metabolic expansion during polyaromatic hydrocarbons rhizoremediation

    Energy Technology Data Exchange (ETDEWEB)

    Rugh, C.L.; Susilawati, E.; Kravchenko, A.N. [Dept. of Crop and Soil Sciences, Michigan State Univ., East Lansing, MI (United States); Thomas, J.C. [Dept. of Natural Sciences, Univ. of Michigan-Dearborn, Dearborn, MI (United States)

    2005-04-01

    Root-microbe interactions are considered to be the primary process of polyaromatic hydrocarbon (PAH) phytoremediation, since bacterial degradation has been shown to be the dominant pathway for environmental PAH dissipation. However, the precise mechanisms driving PAH rhizostimulation symbiosis remain largely unresolved. In this study, we assessed PAH degrading bacterial abundance in contaminated soils planted with 18 different native Michigan plant species. Phenanthrene metabolism assays suggested that each plant species differentially influenced the relative abundance of PAH biodegraders, though they generally were observed to increase heterotrophic and biodegradative cell numbers relative to unplanted soils. Further study of > 1800 phenanthrene degrading isolates indicated that most of the tested plant species stimulated biodegradation of a broader range of PAH compounds relative to the unplanted soil bacterial consortia. These observations suggest that a principal contribution of planted systems for PAH bioremediation may be via expanded metabolic range of the rhizosphere bacterial community. (orig.)

  3. BIOREMEDIATION OF A PETROLEUM-HYDROCARBON

    African Journals Online (AJOL)

    ES OBE

    under field conditions in the bioremediation of a petroleum- hydrocarbon polluted ... an accelerated biodegradation of petroleum hydrocarbons in a polluted agricultural soil ..... 12) Jackson, M.L. Soil chemical analysis. ... biological assay. 3 rd.

  4. Total Petroleum Hydrocarbons (TPH): ToxFAQs

    Science.gov (United States)

    ... a state: This map displays locations where Total Petroleum Hydrocarbons (TPH) is known to be present. On ... I get more information? ToxFAQs TM for Total Petroleum Hydrocarbons (TPH) ( Hidrocarburos Totales de Petróleo (TPH) ) August ...

  5. Analyse géochimique des hydrocarbures légers par thermovaporisation Geochemical Analysis of Light Hydrocarbons by Thermovaporization

    Directory of Open Access Journals (Sweden)

    Jonathan D.

    2006-11-01

    Full Text Available Le procédé de thermovaporisation est utilisé pour l'extraction et l'analyse des hydrocarbures à point d'ébullition situé à l'intérieur de l'intervalle correspondant aux alcanes C6 à C15; il s'applique également aux roches et aux huiles. La mise en ceuvre est simple et rapide, ce qui rend cette technique utilisable dans certains laboratoires de chantiers d'exploration. Les chromatogrammes de vapeurs montrent une succession de pics, chaque pic correspondant théoriquement à un composant défini, alcane, cyclane ou aromatique; la portion située entre les alcanes n-C, et n-C8 est très typée, mais le reste du chromatogramme apporte également des informations importantes ; l'ensemble donne une définition chimique très fine des hydrocarbures légers présents dans l'échantillon. L'exploitation de ces informations en interprétation géochimique est multiple (pouvoir pétroligène de sédiments, état de maturation, etc.. La faible masse de la prise d'essai nécessaire constitue un intérêt essentiel de la méthode. The method called thermovaporization is used to extract and analyse low boiling point hydrocarbons in the range corresponding to C6-C15; alcanes. Sediments and oils ore examined in the same way. This method is simple and fast to utilize, and for this reason it can be applied in some field exploration laboratories. Chromatograms show a sertes of peaks, each of them theoretically corresponding to a particular composant : alkane, cyclone, arcmatics. The part of the chromatogram between n-C7 n-C8 is very characteristic, but other parts also provide a great deal of information. The total chromatogram gives a very fine chemical definition of the light hydrocarbons in the sample. This information can be used for many geochemical interpretations (hydrocarbon yield potential, state of maturation, etc.. Moreover, the tiny amount of sample thot is necessary is of major interest.

  6. Direct production of fractionated and upgraded hydrocarbon fuels from biomass

    Science.gov (United States)

    Felix, Larry G.; Linck, Martin B.; Marker, Terry L.; Roberts, Michael J.

    2014-08-26

    Multistage processing of biomass to produce at least two separate fungible fuel streams, one dominated by gasoline boiling-point range liquids and the other by diesel boiling-point range liquids. The processing involves hydrotreating the biomass to produce a hydrotreatment product including a deoxygenated hydrocarbon product of gasoline and diesel boiling materials, followed by separating each of the gasoline and diesel boiling materials from the hydrotreatment product and each other.

  7. Deep-water northern Gulf of Mexico hydrocarbon plays

    International Nuclear Information System (INIS)

    Peterson, R.H.; Cooke, D.W.

    1995-01-01

    The geologic setting in the deep-water (depths greater than 1,500 feet) Gulf of Mexico is very favorable for the existence of large, commercial hydrocarbon accumulations. These areas have active salt tectonics that create abundant traps, underlying mature Mesozoic source rocks that can be observed expelling oil and gas to the ocean surface, and good quality reservoirs provided by turbidite sand deposits. Despite the limited amount of drilling in the deep-water Gulf of Mexico, 11 deep-water accumulations have been discovered which, when developed, will rank in the top 100 largest fields in the Gulf of Mexico. Proved field discoveries (those with announced development plans) have added over 1 billion barrels of oil equivalent to Gulf of Mexico reserves, and unproved field discoveries may add to additional billion barrels of oil equivalent. The Minerals Management Service, United States Department of the Interior, has completed a gulf-wide review of over 1,086 oil and gas fields and placed every pay sand in each field into a hydrocarbon play (plays are defined by chronostratigraphy, lithostratigraph, structure, and production). Seven productive hydrocarbon plays were identified in the deep-water northern Gulf of Mexico. Regional maps illustrate the productive limits of each play. In addition, field data, dry holes, and wells with sub-economic pay were added to define the facies and structural limits for each play. Areas for exploration potential are identified for each hydrocarbon play. A type field for each play is chosen to demonstrate the play's characteristics

  8. Bioremediation of petroleum hydrocarbons in soil environments. Report No. EE-141

    Energy Technology Data Exchange (ETDEWEB)

    Rowell, M J; Ashworth, J; Qureshi, A A

    1992-01-01

    The bioremediation of petroleum hydrocarbons in soil environments was reviewed by means of a literature survey and also through discussions with workers in relevent disciplines. This report discusses both the impacts of hydrocarbons on soil and a range of methods available to assist in the decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, oily sludges, asphalts and bitumens, drilling mud residues, creosote tars and some pesticides.

  9. Product Maturation Guide - A Digital Simulation Outcome

    DEFF Research Database (Denmark)

    Boorla, Srinivasa Murthy; Howard, Thomas J.

    2016-01-01

    . Tolerance analysis tools, those optimizing the individual part tolerances at the time of design can generate a product maturation guide that eliminates many problem solving procedures and saves time on root cause analysis. Assume a first product built on a new assembly line was found to need improvements....... To conclude the actions we need information about all the dimensions of child parts and processes involved and their influence. At the time of product design, the tolerance analysis system works with the same variables with a given range of variations virtually. For a practical build, instead of variation...... range, it has to consider one fixed value measured from initial parts. By adding information about process characteristics, like speed, cost, etc. to all the dimensions, the system can directly guide the manufacturing team, on which parameter to modify, which direction and how much. At the same time...

  10. Effective viscosity of confined hydrocarbons

    DEFF Research Database (Denmark)

    Sivebæk, Ion Marius; Samoilov, V.N.; Persson, B.N.J.

    2012-01-01

    We present molecular dynamics friction calculations for confined hydrocarbon films with molecular lengths from 20 to 1400 carbon atoms. We find that the logarithm of the effective viscosity ηeff for nanometer-thin films depends linearly on the logarithm of the shear rate: log ηeff=C-nlog γ̇, where...

  11. Information system maturity and the hospitality enterprise performance

    Directory of Open Access Journals (Sweden)

    Daniela Garbin Pranicevic

    2015-01-01

    Full Text Available The purpose of this paper is to empirically evaluate the relationship between the maturity of hotels’ information systems and their performance. This study uses customized models of information system (IS maturity and hotel performance measurement. Since we wanted to include the intangible aspects of performance, we opted for an adapted application of the Balanced Scorecard model. In the empirical part of the paper, fundamental constructs of the model are verified, while the individual items are further evaluated by employing discriminant analysis to distinguish hotels with relatively low and high performance levels. The findings demonstrate the existence of a significant and positive relationship between IS maturity and two dimensions of performance in the hospitality industry – process quality and guest relationships. The level of employee development and financial performance do not seem to be related to IS maturity. Although representative, the sample is relatively small, and the primary data were collected in a single country. The paper provides a framework of IS maturity items in the hospitality industry which seem to contribute to hotels’ business performances. As such, it can serve as a practical framework relevant for IT management in tourism and hospitality. The paper addresses a topic already discussed in a range of industries, although it does not seem to have been empirically evaluated by many studies of the tourism and hospitality industry. In addition, a new theoretical model of IT maturity in tourism and hospitality is proposed.

  12. Artificial maturation of an immature sulfur- and organic matter-rich limestone from the Ghareb Formation, Jordan

    Science.gov (United States)

    Koopmans, M.P.; Rijpstra, W.I.C.; De Leeuw, J. W.; Lewan, M.D.; Damste, J.S.S.

    1998-01-01

    An immature (Ro=0.39%), S-rich (S(org)/C = 0.07), organic matter-rich (19.6 wt. % TOC) limestone from the Ghareb Formation (Upper Cretaceous) in Jordan was artificially matured by hydrous pyrolysis (200, 220 ..., 300??C; 72 h) to study the effect of progressive diagenesis and early catagenesis on the amounts and distributions of hydrocarbons, organic sulfur compounds and S-rich geomacromolecules. The use of internal standards allowed the determination of absolute amounts. With increasing thermal maturation, large amounts of alkanes and alkylthiophenes with predominantly linear carbon skeletons are generated from the kerogen. The alkylthiophene isomer distributions do not change significantly with increasing thermal maturation, indicating the applicability of alkylthiophenes as biomarkers at relatively high levels of thermal maturity. For a given carbon skeleton, the saturated hydrocarbon, alkylthiophenes and alkylbenzo[b]thiophenes are stable forms at relatively high temperatures, whereas the alkylsulfides are not stable. The large amount of alkylthiophenes produced relative to the alkanes may be explained by the large number of monosulfide links per carbon skeleton. These results are in good agreement with those obtained previously for an artificial maturation series of an immature S-rich sample from the Gessoso-solfifera Formation.An immature (Ro = 0.39%), S-rich (Sorg/C = 0.07), organic matter-rich (19.6 wt.% TOC) limestone from the Ghareb Formation (Upper Cretaceous) in Jordan was artificially matured by hydrous pyrolysis (200, 220, ..., 300??C; 72 h) to study the effect of progressive diagenesis and early catagenesis on the amounts and distributions of hydrocarbons, organic sulfur compounds and S-rich geomacromolecules. The use of internal standards allowed the determination of absolute amounts. With increasing thermal maturation, large amounts of alkanes and alkylthiophenes with predominantly linear carbon skeletons are generated from the kerogen. The

  13. Migrated hydrocarbons in outcrop samples: revised petroleum exploration directions in the Tarim Basin

    Energy Technology Data Exchange (ETDEWEB)

    Li, Maowen; Snowdon, Lloyd [Geological Survey of Canada, Calgary, AB (Canada); Xiao, Zhongyao [CNPC Tarim Petroleum Exploration Bureau, Kuerle, Xinjiang (China); Lin, Renzi [Petroleum Univ., Changping, Beijing (China); Wang, Peirong; Hou, Dujie [Jianghan Petroleum Univ., Hubei (China); Zhang, Linye [SINOPEC Shengli Petroleum Bureau, Dongying, Shandong (China); Zhang, Shuichang; Liang, Digang [Research Inst. of Petroleum Exploration and Development, Beijing (China)

    2000-07-01

    The application of age-specific biomarker distributions established from mature exploration areas of the Tarim Basin, northwestern China, indicates that most Carboniferous-Permian outcrop samples in the eastern segment of the Southwest Depression, previously believed to have significant petroleum source potential, in fact contain migrated hydrocarbons derived from Cambrian-Lower Ordovician strata. New geochemical results have led to a major revision of petroleum exploration directions in this area. (Author)

  14. Cervical vertebral maturation as a biologic indicator of skeletal maturity.

    Science.gov (United States)

    Santiago, Rodrigo César; de Miranda Costa, Luiz Felipe; Vitral, Robert Willer Farinazzo; Fraga, Marcelo Reis; Bolognese, Ana Maria; Maia, Lucianne Cople

    2012-11-01

    To identify and review the literature regarding the reliability of cervical vertebrae maturation (CVM) staging to predict the pubertal spurt. The selection criteria included cross-sectional and longitudinal descriptive studies in humans that evaluated qualitatively or quantitatively the accuracy and reproducibility of the CVM method on lateral cephalometric radiographs, as well as the correlation with a standard method established by hand-wrist radiographs. The searches retrieved 343 unique citations. Twenty-three studies met the inclusion criteria. Six articles had moderate to high scores, while 17 of 23 had low scores. Analysis also showed a moderate to high statistically significant correlation between CVM and hand-wrist maturation methods. There was a moderate to high reproducibility of the CVM method, and only one specific study investigated the accuracy of the CVM index in detecting peak pubertal growth. This systematic review has shown that the studies on CVM method for radiographic assessment of skeletal maturation stages suffer from serious methodological failures. Better-designed studies with adequate accuracy, reproducibility, and correlation analysis, including studies with appropriate sensitivity-specificity analysis, should be performed.

  15. Correlation Between Dental and Cervical Vertebral Maturation in Iranian Females

    Science.gov (United States)

    Valizadeh, Solmaz; Eil, Nakissa; Ehsani, Sara; Bakhshandeh, Hooman

    2012-01-01

    Background Considerable variations in the development stage among patients of the same chronological age have led to introduce the concept of the developmental age based on the maturation of different organs such as cervical vertebrae or teeth. Objectives The purpose of this study was to investigate the correlation between the stages of tooth calcification and the cervical vertebral maturation in Iranian females. Patients and Methods Four hundred females (age range, 8 to 14 years) participated in the study. To determine the dental maturational stage, calcification of the mandibular teeth except for third molars were rated according to the method suggested by Demirjian et al. To evaluate the stage of skeletal maturation, cervical vertebral morphologic changes were assessed on lateral cephalometric radiographs according to the method explained by Baccetti et al. Correlations between bone maturation and teeth calcification were showed by Spearman's correlation and Kendall’s tau-b coefficients. The relevant associations were investigated by ordinal logistic regression models. Results Correlations between the two stages were observed in the first and second premolars, canine and central incisors. All these correlations were significant. The association between cervical vertebral maturation and tooth calcification was greatest in the lateral incisor (odds ratio (OR) = 11, 95% confidence interval (CI): 6.6-18.3). However, considering the 95% CI for OR, no significant difference was detected among the second molar, first molar and lateral incisor. Conclusion The relationship between calcification of teeth and maturation of cervical bones was significant. Bone maturation can be predicted by using teeth calcification stages, especially in the second molar, first molar and lateral incisor. PMID:23599706

  16. Correlation between dental and cervical vertebral maturation in Iranian females.

    Science.gov (United States)

    Valizadeh, Solmaz; Eil, Nakissa; Ehsani, Sara; Bakhshandeh, Hooman

    2012-12-01

    Considerable variations in the development stage among patients of the same chronological age have led to introduce the concept of the developmental age based on the maturation of different organs such as cervical vertebrae or teeth. The purpose of this study was to investigate the correlation between the stages of tooth calcification and the cervical vertebral maturation in Iranian females. Four hundred females (age range, 8 to 14 years) participated in the study. To determine the dental maturational stage, calcification of the mandibular teeth except for third molars were rated according to the method suggested by Demirjian et al. To evaluate the stage of skeletal maturation, cervical vertebral morphologic changes were assessed on lateral cephalometric radiographs according to the method explained by Baccetti et al. Correlations between bone maturation and teeth calcification were showed by Spearman's correlation and Kendall's tau-b coefficients. The relevant associations were investigated by ordinal logistic regression models. Correlations between the two stages were observed in the first and second premolars, canine and central incisors. All these correlations were significant. The association between cervical vertebral maturation and tooth calcification was greatest in the lateral incisor (odds ratio (OR) = 11, 95% confidence interval (CI): 6.6-18.3). However, considering the 95% CI for OR, no significant difference was detected among the second molar, first molar and lateral incisor. The relationship between calcification of teeth and maturation of cervical bones was significant. Bone maturation can be predicted by using teeth calcification stages, especially in the second molar, first molar and lateral incisor.

  17. Fate of diesel fuel hydrocarbon in composting bioremediation system using radio- labeled 14C phenanthrene

    International Nuclear Information System (INIS)

    Hesnawi, R. M.; McCartney, D. M.

    2008-01-01

    To characterize the fate of fuel hydrocarbon in bioremediation composting system, diesel fuel, spiked with radio-labeled [9-1 4C ] phenanthrene at activity of 0.15μCi g - 1 of diesel fuel, was added to the soil to yield a contaminant load of 20,000 mg kg - 1 dry soil. The contaminated soil was amended with either fresh feedstock material (municipal sludge, leaves, and wood shaving) or mature compost and then incubated at thermophilic temperature pattern for 126 day. The mineralized, volatilized, and extractable fractions of 1 4C labeled phenanthrene were determined every two weeks over 126-days experimental period. The 1 4C data were used to predict the amount of removal due to biodegradation and sorption. In controls that were not amended with compost, no mineralization of 1 4C phenanthrene was detected, whereas treatments that received compost amendment showed significant release of phenanthrene as 1 4C O 2., ranging from 25% to 42% of initial radioactivity concentrations. The 1 4C extracted from the solids were decreasing with time. The total radioactivity extracted at the end of the experiment was less than 11% in the amended soil, whereas in the controls, more than 65% of the 1 4C was extracted. The 1 4C data indicated that bound residues formation was the major mechanism for the removal of pantherine or its metabolites. (author)

  18. Burial history, thermal history and hydrocarbon generation modelling of the Jurassic source rocks in the basement of the Polish Carpathian Foredeep and Outer Carpathians (SE Poland)

    Science.gov (United States)

    Kosakowski, Paweł; Wróbel, Magdalena

    2012-08-01

    Burial history, thermal maturity, and timing of hydrocarbon generation were modelled for the Jurassic source rocks in the basement of the Carpathian Foredeep and marginal part of the Outer Carpathians. The area of investigation was bounded to the west by Kraków, to the east by Rzeszów. The modelling was carried out in profiles of wells: Będzienica 2, Dębica 10K, Góra Ropczycka 1K, Goleszów 5, Nawsie 1, Pławowice E1 and Pilzno 40. The organic matter, containing gas-prone Type III kerogen with an admixture of Type II kerogen, is immature or at most, early mature to 0.7 % in the vitrinite reflectance scale. The highest thermal maturity is recorded in the south-eastern part of the study area, where the Jurassic strata are buried deeper. The thermal modelling showed that the obtained organic matter maturity in the initial phase of the "oil window" is connected with the stage of the Carpathian overthrusting. The numerical modelling indicated that the onset of hydrocarbon generation from the Middle Jurassic source rocks was also connected with the Carpathian thrust belt. The peak of hydrocarbon generation took place in the orogenic stage of the overthrusting. The amount of generated hydrocarbons is generally small, which is a consequence of the low maturity and low transformation degree of kerogen. The generated hydrocarbons were not expelled from their source rock. An analysis of maturity distribution and transformation degree of the Jurassic organic matter shows that the best conditions for hydrocarbon generation occurred most probably in areas deeply buried under the Outer Carpathians. It is most probable that the "generation kitchen" should be searched for there.

  19. The Development of Marital Maturity Scale

    Directory of Open Access Journals (Sweden)

    Muhammed YILDIZ

    2017-06-01

    Full Text Available In this study, validity, reliability and item analysis studies of the Marital Maturity Scale prepared to test whether individuals are ready for marriage have been done. Studies of the development of the scale were made on 623 individuals, consisting of single adults. In the validity studies of the scale, explanatory and confirmatory factor analyses and criterion related validity studies were performed. Factor analysis revealed that the scale had four dimensions. The four factors in the measurement account for 60.91% of the total variance. The factor loadings of the items in the scale range from 0.42 to 0.86. Inonu Marriage Attitude Scale was used in the criterion related validity studies. Correlation value of the two scales r=0.72 (p=0.000 was found significant. It was determined that the subscales of the scale had a significant correlation with the total scale. The cronbach alpha value of the first dimension of the scale was 0.85, the cronbach alpha value of the second dimension of the scale was 0.68, the cronbach alpha value of the third dimension of the scale was 0.80, the cronbach alpha value of the fourth dimension of the scale was 0.91 and the cronbach alpha value of the total scale was 0.90. Test retest results r=0.70, (p=0.000 were found significant. In the item analysis studies, it was revealed that in the lower 27% group, the individuals in the upper 27% group were significantly different in all items (p=0.000. The item total correlation value of the items in the scale was between 0.40 and 0.63. As a result of the assessments, it was concluded that the Marital Maturity Scale was a reliable and valid instrument to measure marital maturity of single adults

  20. Cholinesterase inhibitory activity and chemical constituents of Stenochlaena palustris fronds at two different stages of maturity

    Directory of Open Access Journals (Sweden)

    Nelson Jeng-Yeou Chear

    2016-04-01

    Full Text Available Stenochlaena palustris fronds are popular as a vegetable in Southeast Asia. The objectives of this study were to evaluate the anticholinesterase properties and phytochemical profiles of the young and mature fronds of this plant. Both types of fronds were found to have selective inhibitory effect against butyrylcholinesterase compared with acetylcholinesterase. However, different sets of compounds were responsible for their activity. In young fronds, an antibutyrylcholinesterase effect was observed in the hexane extract, which was comprised of a variety of aliphatic hydrocarbons, fatty acids, and phytosterols. In the mature fronds, inhibitory activity was observed in the methanol extract, which contained a series of kaempferol glycosides. Our results provided novel information concerning the ability of S. palustris to inhibit cholinesterase and its phytochemical profile. Further research to investigate the potential use of this plant against Alzheimer's disease is warranted, however, young and mature fronds should be distinguished due to their phytochemical differences.

  1. Characterization of coal-derived hydrocarbons and source-rock potential of coal beds, San Juan Basin, New Mexico and Colorado, U.S.A.

    Science.gov (United States)

    Rice, D.D.; Clayton, J.L.; Pawlewicz, M.J.

    1989-01-01

    .5 ppt), are chemically wetter (C1/C1-5 values range from 0.85 to 0.95), and contain less CO2 (< 2%). These gases are interpreted to have been derived from type III kerogen dispersed in marine shales of the underlying Lewis Shale and nonmarine shales of the Fruitland Formation. In the underlying Upper Cretaceous Dakota Sandstone and Tocito Sandstone Lentil of the Mancos Shale, another gas type is produced. This gas is associated with oil at intermediate stages of thermal maturity and is isotopically lighter and chemically wetter at the intermediate stage of thermal maturity as compared with gases derived from dispersed type III kerogen and coal; this gas type is interpreted to have been generated from type II kerogen. Organic matter contained in coal beds and carbonaceous shales of the Fruitland Formation has hydrogen indexes from Rock-Eval pyrolysis between 100 and 350, and atomic H:C ratios between 0.8 and 1.2. Oxygen indexes and atomic O:C values are less than 24 and 0.3, respectively. Extractable hydrocarbon yields are as high as 7,000 ppm. These values indicate that the coal beds and carbonaceous shales have good potential for the generation of liquid hydrocarbons. Voids in the coal filled with a fluorescent material that is probably bitumen is evidence that liquid hydrocarbon generation has taken place. Preliminary oil-source rock correlations based on gas chromatography and stable carbon isotope ratios of C15+ hydrocarbons indicate that the coals and (or) carbonaceous shales in the Fruitland Formation may be the source of minor amounts of condensate produced from the coal beds at relatively low levelsof thermal maturity (Rm=0.7). ?? 1989.

  2. Biodegradation of petroleum hydrocarbons in hypersaline environments

    Directory of Open Access Journals (Sweden)

    Luiz Fernando Martins

    2012-09-01

    Full Text Available Literature on hydrocarbon degradation in extreme hypersaline media presents studies that point to a negative effect of salinity increase on hydrocarbonoclastic activity, while several others report an opposite tendency. Based on information available in the literature, we present a discussion on the reasons that justify these contrary results. Despite the fact that microbial ability to metabolize hydrocarbons is found in extreme hypersaline media, indeed some factors are critical for the occurrence of hydrocarbon degradation in such environments. How these factors affect hydrocarbon degradation and their implications for the assessment of hydrocarbon biodegradation in hypersaline environments are presented in this review.

  3. Process for separating liquid hydrocarbons from waxes

    Energy Technology Data Exchange (ETDEWEB)

    Sowa, F J

    1948-03-08

    A process is described for the separation of liquid hydrocarbons from waxes comprising adding to a mixture of liquid hydrocarbons and waxes a sufficient quantity of an organo-silicon compound to cause the separation of the hydrocarbon and wax. The organo-silicon compounds are selected from the class of organic silicanes and their hydrolysis products and polymers. The silicanes have the formula R/sub y/SiX/sub z/, in which R is a saturated or unsaturated hydrocarbon radical, X is a halogen or another hydrocarbon radical or an -OR group, y has a value 1, 2, or 3 and z has a value 1, 2, or 3.

  4. Thermal maturity of northern Appalachian Basin Devonian shales: Insights from sterane and terpane biomarkers

    Science.gov (United States)

    Hackley, Paul C.; Ryder, Robert T.; Trippi, Michael H.; Alimi, Hossein

    2013-01-01

    To better estimate thermal maturity of Devonian shales in the northern Appalachian Basin, eleven samples of Marcellus and Huron Shale were characterized via multiple analytical techniques. Vitrinite reflectance, Rock–Eval pyrolysis, gas chromatography (GC) of whole rock extracts, and GC–mass spectrometry (GCMS) of extract saturate fractions were evaluated on three transects that lie across previously documented regional thermal maturity isolines. Results from vitrinite reflectance suggest that most samples are immature with respect to hydrocarbon generation. However, bulk geochemical data and sterane and terpane biomarker ratios from GCMS suggest that almost all samples are in the oil window. This observation is consistent with the presence of thermogenic gas in the study area and higher vitrinite reflectance values recorded from overlying Pennsylvanian coals. These results suggest that vitrinite reflectance is a poor predictor of thermal maturity in early mature areas of Devonian shale, perhaps because reported measurements often include determinations of solid bitumen reflectance. Vitrinite reflectance interpretations in areas of early mature Devonian shale should be supplanted by evaluation of thermal maturity information from biomarker ratios and bulk geochemical data.

  5. Maturation of the adolescent brain

    Directory of Open Access Journals (Sweden)

    Arain M

    2013-04-01

    Full Text Available Mariam Arain, Maliha Haque, Lina Johal, Puja Mathur, Wynand Nel, Afsha Rais, Ranbir Sandhu, Sushil Sharma Saint James School of Medicine, Kralendijk, Bonaire, The Netherlands Abstract: Adolescence is the developmental epoch during which children become adults – intellectually, physically, hormonally, and socially. Adolescence is a tumultuous time, full of changes and transformations. The pubertal transition to adulthood involves both gonadal and behavioral maturation. Magnetic resonance imaging studies have discovered that myelinogenesis, required for proper insulation and efficient neurocybernetics, continues from childhood and the brain's region-specific neurocircuitry remains structurally and functionally vulnerable to impulsive sex, food, and sleep habits. The maturation of the adolescent brain is also influenced by heredity, environment, and sex hormones (estrogen, progesterone, and testosterone, which play a crucial role in myelination. Furthermore, glutamatergic neurotransmission predominates, whereas gamma-aminobutyric acid neurotransmission remains under construction, and this might be responsible for immature and impulsive behavior and neurobehavioral excitement during adolescent life. The adolescent population is highly vulnerable to driving under the influence of alcohol and social maladjustments due to an immature limbic system and prefrontal cortex. Synaptic plasticity and the release of neurotransmitters may also be influenced by environmental neurotoxins and drugs of abuse including cigarettes, caffeine, and alcohol during adolescence. Adolescents may become involved with offensive crimes, irresponsible behavior, unprotected sex, juvenile courts, or even prison. According to a report by the Centers for Disease Control and Prevention, the major cause of death among the teenage population is due to injury and violence related to sex and substance abuse. Prenatal neglect, cigarette smoking, and alcohol consumption may also

  6. Characterization of cyanobacterial hydrocarbon composition and distribution of biosynthetic pathways.

    Directory of Open Access Journals (Sweden)

    R Cameron Coates

    Full Text Available Cyanobacteria possess the unique capacity to naturally produce hydrocarbons from fatty acids. Hydrocarbon compositions of thirty-two strains of cyanobacteria were characterized to reveal novel structural features and insights into hydrocarbon biosynthesis in cyanobacteria. This investigation revealed new double bond (2- and 3-heptadecene and methyl group positions (3-, 4- and 5-methylheptadecane for a variety of strains. Additionally, results from this study and literature reports indicate that hydrocarbon production is a universal phenomenon in cyanobacteria. All cyanobacteria possess the capacity to produce hydrocarbons from fatty acids yet not all accomplish this through the same metabolic pathway. One pathway comprises a two-step conversion of fatty acids first to fatty aldehydes and then alkanes that involves a fatty acyl ACP reductase (FAAR and aldehyde deformylating oxygenase (ADO. The second involves a polyketide synthase (PKS pathway that first elongates the acyl chain followed by decarboxylation to produce a terminal alkene (olefin synthase, OLS. Sixty-one strains possessing the FAAR/ADO pathway and twelve strains possessing the OLS pathway were newly identified through bioinformatic analyses. Strains possessing the OLS pathway formed a cohesive phylogenetic clade with the exception of three Moorea strains and Leptolyngbya sp. PCC 6406 which may have acquired the OLS pathway via horizontal gene transfer. Hydrocarbon pathways were identified in one-hundred-forty-two strains of cyanobacteria over a broad phylogenetic range and there were no instances where both the FAAR/ADO and the OLS pathways were found together in the same genome, suggesting an unknown selective pressure maintains one or the other pathway, but not both.

  7. Abundances of polycyclic aromatic hydrocarbons (PAHs) in 14 chinese and american coals and their relation to coal rank and weathering

    Science.gov (United States)

    Wang, R.; Liu, Gaisheng; Zhang, Jiahua; Chou, C.-L.; Liu, J.

    2010-01-01

    The abundances of 16 polycyclic aromatic hydrocarbons (PAHs) on the priority list of the United States Environmental Protection Agency (U.S. EPA) have been determined in 14 Chinese and American coals. The ranks of the samples range from lignite, bituminous coal, anthracite, to natural coke. Soxhlet extraction was conducted on each coal for 48 h. The extract was analyzed on a gas chromatograph-mass spectrometer (GC-MS). The results show that the total PAH content ranged from 0.31 to 57.6 ??g/g of coal (on a dry basis). It varied with coal rank and is highest in the maturity range of bituminous coal rank. High-molecular-weight (HMW) PAHs are predominant in low-rank coals, but low-molecular-weight (LMW) PAHs are predominant in high-rank coals. The low-sulfur coals have a higher PAH content than high-sulfur coals. It may be explained by an increasing connection between disulfide bonds and PAHs in high-sulfur coal. In addition, it leads us to conclude that the PAH content of coals may be related to the depositional environment. ?? 2010 American Chemical Society.

  8. Constraining the Thermal History of the Midcontinent Rift System with Clumped Isotopes and Organic Thermal Maturity Indices

    Science.gov (United States)

    Gallagher, T. M.; Sheldon, N. D.; Mauk, J. L.; Gueneli, N.; Brocks, J. J.

    2015-12-01

    The Mesoproterozoic (~1.1 Ga) North American Midcontinent Rift System (MRS) has been of widespread interest to researchers studying its economic mineral deposits, continental rifting processes, and the evolution of early terrestrial life and environments. For their age, the MRS rocks are well preserved and have not been deeply buried, yet a thorough understanding of the regional thermal history is necessary to constrain the processes that emplaced the mineral deposits and how post-burial alteration may have affected various paleo-records. To understand the thermal history of the MRS better, this study presents carbonate clumped isotope (Δ47) temperatures from deposits on the north and south sides of the rift. Due to the age of these deposits and known post-depositional processes, uncertainties exist about whether the clumped isotope signature has been reset. To test this, three generations of calcite were analyzed from the Nonesuch Fm. from the White Pine mine in Michigan including: sedimentary limestone beds, early diagenetic carbonate nodules, and hydrothermal calcite veins associated with the emplacement of copper mineralization. Clumped isotope temperatures from the White Pine mine range from 84 to 131°C, with a hydrothermal vein producing the hottest temperature. The clumped isotope temperature range for samples throughout the rift expands to 41-134°C. The hottest temperatures are associated with areas of known copper mineralization, whereas the coolest temperatures are found on the northern arm of the rift in Minnesota, far from known basin-bounding faults. Our hottest temperatures are broadly consistent with preexisting maximum thermal temperature estimates based on clay mineralogy, fluid inclusions, and organic geochemistry data. Clumped isotope results will also be compared to new hydrocarbon maturity data from the Nonesuch Fm., which suggest that bitumen maturities consistently fall within the early oil window across Michigan and Wisconsin.

  9. Tolerance of Antarctic soil fungi to hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, Kevin A.; Bridge, Paul; Clark, Melody S. [British Antarctic Survey, Natural Environment Research Council, High Cross, Madingley Road, Cambridge CB3 0ET (United Kingdom)

    2007-01-01

    Little is known about the effects of hydrocarbons and fuel oil on Antarctic filamentous fungi in the terrestrial Antarctic environment. Growth of fungi and bacteria from soils around Rothera Research Station (Adelaide Island, Antarctic Peninsula) was assessed in the presence of ten separate aromatic and aliphatic hydrocarbons [marine gas oil (MGO), dodecane, hexadecane, benzoic acid, p-hydroxybenzoic acid, toluene, phenol, biphenyl, naphthalene and m- and p-xylenes with ethylbenzene]. Aromatic hydrocarbons inhibited soil microbial growth more than aliphatic hydrocarbons. Soil microorganisms from a moss patch, where little previous impact or hydrocarbon contamination had occurred, were less tolerant of hydrocarbons than those from high impact sites. Fungal growth rates of Mollisia sp., Penicillium commune, Mortierella sp., Trichoderma koningii, Trichoderma sp. and Phoma herbarum were assessed in the presence of hydrocarbons. Generally, aromatic hydrocarbons inhibited or stopped hyphal extension, though growth rates increased with some aliphatic hydrocarbons. Hyphal dry weight measurements suggested that Mortierella sp. may be able to use dodecane as sole carbon and energy source. Hydrocarbon-degrading Antarctic fungi may have use in future hydrocarbon spill bioremediation. (author)

  10. Home range and travels

    Science.gov (United States)

    Stickel, L.F.; King, John A.

    1968-01-01

    The concept of home range was expressed by Seton (1909) in the term 'home region,' which Burr (1940, 1943) clarified with a definition of home range and exemplified in a definitive study of Peromyscus in the field. Burt pointed out the ever-changing characteristics of home-range area and the consequent absence of boundaries in the usual sense--a finding verified by investigators thereafter. In the studies summarized in this paper, sizes of home ranges of Peromyscus varied within two magnitudes, approximately from 0.1 acre to ten acres, in 34 studies conducted in a variety of habitats from the seaside dunes of Florida to the Alaskan forests. Variation in sizes of home ranges was correlated with both environmental and physiological factors; with habitat it was conspicuous, both in the same and different regions. Food supply also was related to size of home range, both seasonally and in relation to habitat. Home ranges generally were smallest in winter and largest in spring, at the onset of the breeding season. Activity and size also were affected by changes in weather. Activity was least when temperatures were low and nights were bright. Effects of rainfall were variable. Sizes varied according to sex and age; young mice remained in the parents' range until they approached maturity, when they began to travel more widely. Adult males commonly had larger home ranges than females, although there were a number of exceptions. An inverse relationship between population density and size of home range was shown in several studies and probably is the usual relationship. A basic need for activity and exploration also appeared to influence size of home range. Behavior within the home range was discussed in terms of travel patterns, travels in relation to home sites and refuges, territory, and stability of size of home range. Travels within the home range consisted of repeated use of well-worn trails to sites of food, shelter, and refuge, plus more random exploratory travels

  11. Calculating in situ degradation rates of hydrocarbon compounds in deep waters of the Gulf of Mexico.

    Science.gov (United States)

    Thessen, Anne E; North, Elizabeth W

    2017-09-15

    Biodegradation is an important process for hydrocarbon weathering that influences its fate and transport, yet little is known about in situ biodegradation rates of specific hydrocarbon compounds in the deep ocean. Using data collected in the Gulf of Mexico below 700m during and after the Deepwater Horizon oil spill, we calculated first-order degradation rate constants for 49 hydrocarbons and inferred degradation rate constants for an additional 5 data-deficient hydrocarbons. Resulting calculated (not inferred) half-lives of the hydrocarbons ranged from 0.4 to 36.5days. The fastest degrading hydrocarbons were toluene (k=-1.716), methylcyclohexane (k=-1.538), benzene (k=-1.333), and C1-naphthalene (k=-1.305). The slowest degrading hydrocarbons were the large straight-chain alkanes, C-26 through C-33 (k=-0.0494 through k=-0.007). Ratios of C-18 to phytane supported the hypothesis that the primary means of degradation in the subsurface was microbial biodegradation. These degradation rate constants can be used to improve models describing the fate and transport of hydrocarbons in the event of an accidental deep ocean oil spill. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Chlorinated hydrocarbon contaminants in arctic marine mammals.

    Science.gov (United States)

    Norstrom, R J; Muir, D C

    1994-09-16

    By 1976, the presence of chlorinated hydrocarbon contaminants (CHCs) had been demonstrated in fur seal (Callorhinus ursinus), ringed seal (Phoca hispida), hooded seal (Cystophora cristata), bearded seal (Erignathus barbatus), walrus (Obdobenus rosmarus divergens), beluga (Delphinapterus leucas), porpoise (Phocoena phocoena) and polar bear (Ursus maritimus) in various parts of the Arctic. In spite of this early interest, very little subsequent research on contaminants in Arctic marine mammals was undertaken until the mid-1980s. Since that time, there has been an explosion of interest, resulting in a much expanded data base on contaminants in Arctic marine mammals. Except in the Russian Arctic, data have now been obtained on the temporospatial distribution of PCBs and other contaminants in ringed seal, beluga and polar bear. Contaminants in narwhal (Monodon monoceros) have also now been measured. On a fat weight basis, the sum of DDT-related compounds (S-DDT) and PCB levels are lowest in walrus (Polar bears have similar levels of PCBs as cetaceans (1-10 micrograms/g), but with a much simpler congener pattern. DDE levels are lowest in polar bear, indicating rapid metabolism. Effects of age and sex on residue levels are found for all species where this was measured. Among cetaceans and ringed seal, sexually mature females have lower levels than males due to lactation. Although PCB levels in adult male polar bears are about twice as high as females, there is only a trivial age effect in either sex apart from an initial decrease from birth to sexual maturity (age 0-5). Comparison of levels of S-DDT and PCBs in Arctic beluga and ringed seal with those in beluga in the Gulf of St. Lawrence and ringed seal in the Baltic Sea, indicate that overall contamination of the Arctic marine ecosystem is 10-50 times less than the most highly contaminated areas in the northern hemisphere temperate latitude marine environment. Geographic distribution of residue levels in polar bears

  13. Identification of interstellar polysaccharides and related hydrocarbons

    International Nuclear Information System (INIS)

    Hoyle, F.; Olavesen, A.H.; Wickramasinghe, N.C.

    1978-01-01

    A discussion is presented on the infrared transmittance spectra of several polysaccharides that may be of interest as possible interstellar candidates. It is stated that a 2.5 to 15 μm spectrum computed from the author's measurements is remarkably close to that required to explain a wide range of astronomical data, except for two points. First the required relative opacity at the 3 μm absorption dip is a factor of about 1.5 lower than was found in laboratory measurements; this difference may arise from the presence of water in terrestrial polysaccharide samples. Secondly, in the 9.5 to 12 μm waveband an additional source of opacity appears to be necessary. Close agreement between the spectrum of this additional opacity and the absorption spectrum of propene, C 3 H 6 , points strongly to the presence of hydrocarbons of this type, which may be associated with polysaccharide grains in interstellar space. (U.K.)

  14. Polycyclic aromatic hydrocarbons (PAHs) in yogurt samples.

    Science.gov (United States)

    Battisti, Chiara; Girelli, Anna Maria; Tarola, Anna Maria

    2015-01-01

    The concentrations and distributions of major polycyclic aromatic hydrocarbons (PAHs) were determined in 20 kinds of yogurt specimens collected from Italian supermarkets using reversed phase high-performance liquid chromatography equipped with fluorescence detection. The method was validated by determination of recovery percentages, precision (repeatability) and sensitivity (limits of detection) with yogurt samples fortified at 0.25, 0.5 and 1 µg/kg concentration levels. The recovery of 13 PAHs, with the exception of naphthalene and acenaphthene, ranged from 61% to 130% and from 60% to 97% at all the levels for yogurts with low (0.1%) and high (3.9%) fat content, respectively. The method is repeatable with relative standard deviation values yogurts with low and high fats were compared.

  15. Hydrocarbon Rocket Technology Impact Forecasting

    Science.gov (United States)

    Stuber, Eric; Prasadh, Nishant; Edwards, Stephen; Mavris, Dimitri N.

    2012-01-01

    Ever since the Apollo program ended, the development of launch propulsion systems in the US has fallen drastically, with only two new booster engine developments, the SSME and the RS-68, occurring in the past few decades.1 In recent years, however, there has been an increased interest in pursuing more effective launch propulsion technologies in the U.S., exemplified by the NASA Office of the Chief Technologist s inclusion of Launch Propulsion Systems as the first technological area in the Space Technology Roadmaps2. One area of particular interest to both government agencies and commercial entities has been the development of hydrocarbon engines; NASA and the Air Force Research Lab3 have expressed interest in the use of hydrocarbon fuels for their respective SLS Booster and Reusable Booster System concepts, and two major commercially-developed launch vehicles SpaceX s Falcon 9 and Orbital Sciences Antares feature engines that use RP-1 kerosene fuel. Compared to engines powered by liquid hydrogen, hydrocarbon-fueled engines have a greater propellant density (usually resulting in a lighter overall engine), produce greater propulsive force, possess easier fuel handling and loading, and for reusable vehicle concepts can provide a shorter turnaround time between launches. These benefits suggest that a hydrocarbon-fueled launch vehicle would allow for a cheap and frequent means of access to space.1 However, the time and money required for the development of a new engine still presents a major challenge. Long and costly design, development, testing and evaluation (DDT&E) programs underscore the importance of identifying critical technologies and prioritizing investment efforts. Trade studies must be performed on engine concepts examining the affordability, operability, and reliability of each concept, and quantifying the impacts of proposed technologies. These studies can be performed through use of the Technology Impact Forecasting (TIF) method. The Technology Impact

  16. Microbial production of gaseous hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Fukuda, Hideo

    1987-10-20

    Microbial production of ethylene, isobutane and a saturated gaseous hydrocarbon mixture was described. Microbial ethylene production was studied with Penicillium digitatum IFO 9372 and a novel pathway of the ethylene biosynthesis through alpha-ketoglutarate was proposed. Rhodotorula minuta IFO 1102 was selected for the microbial production of isobutane and the interesting actions of L-leucine and L-phenylalanine for the isobutane production were found. It was finally presented about the microbial production of a saturated gaseous hydrocarbon mixture with Rhizopus japonicus IFO 4758 was described. A gas mixture was produced through a chemical reaction of SH compounds and some cellular component such as squalene under aerobic conditions. (4 figs, 7 tabs, 41 refs)

  17. Scottish hydrocarbons: Borders and bounty

    International Nuclear Information System (INIS)

    Roberts, John

    1999-01-01

    On 6 May, the people of Scotland will vote for the country's first parliament in almost three centuries. One issue is expected to arouse particularly strong views: the question of North Sea oil and gas, and who benefits from its production and taxation. Most of these hydrocarbons lie in the northern half of the British Isles, but drawing boundaries to settle contentious issues such as oil and gas fields is not an easy task. And, if boundaries were to be drawn, then a scarcely less contentious subject arises: just how much cash might an independent Scotland expect to receive? Reading between the lines it's clear that in hard cash terms, were Scotland to be independent whilst still retaining the vast bulk of North Sea oilfields, depressed prices would ensure that hydrocarbon tax revenues would be unlikely to constitute a particularly impressive addition to the Scottish Treasury. (UK)

  18. 7 CFR 51.1904 - Maturity classification.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Maturity classification. 51.1904 Section 51.1904... STANDARDS) United States Consumer Standards for Fresh Tomatoes Size and Maturity Classification § 51.1904 Maturity classification. Tomatoes which are characteristically red when ripe, but are not overripe or soft...

  19. Treatment of hydrocarbon oil vapours

    Energy Technology Data Exchange (ETDEWEB)

    Lamplough, F

    1923-03-01

    An apparatus for treating hydrocarbon vapors for the purpose of preventing dehydrogenation is disclosed which comprises in combination a cooling tower having a vapor inlet at the bottom and a vapor outlet at the top, means to direct the entering vapors laterally in a plurality of jets against an interior side wall or walls of the tower and means to constrain the condensate to gravitate down the tower in the interior wall or walls against which the encountering vapor is forced to impinge.

  20. Deep desulfurization of hydrocarbon fuels

    Science.gov (United States)

    Song, Chunshan [State College, PA; Ma, Xiaoliang [State College, PA; Sprague, Michael J [Calgary, CA; Subramani, Velu [State College, PA

    2012-04-17

    The invention relates to processes for reducing the sulfur content in hydrocarbon fuels such as gasoline, diesel fuel and jet fuel. The invention provides a method and materials for producing ultra low sulfur content transportation fuels for motor vehicles as well as for applications such as fuel cells. The materials and method of the invention may be used at ambient or elevated temperatures and at ambient or elevated pressures without the need for hydrogen.

  1. Source rock hydrocarbons. Present status

    International Nuclear Information System (INIS)

    Vially, R.; Maisonnier, G.; Rouaud, T.

    2013-01-01

    This report first presents the characteristics of conventional oil and gas system, and the classification of liquid and gaseous non conventional hydrocarbons, with the peculiar case of coal-bed methane. The authors then describe how source rock hydrocarbons are produced: production of shale oils and gases (horizontal drilling, hydraulic fracturing, exploitation) and of coal-bed methane and coal mine methane. In the next part, they address and discuss the environmental impact of source rock hydrocarbon production: installation footprint, water resource management, drilling fluids, fracturing fluids composition, toxicity and recycling, air pollution, induced seismicity, pollutions from other exploitation and production activities. They propose an overview of the exploitation and production of source rock gas, coal-bed gas and other non conventional gases in the world. They describe the current development and discuss their economic impacts: world oil context and trends in the USA, in Canada and other countries, impacts on the North American market, on the world oil industry, on refining industries, on the world oil balance. They analyse the economic impacts of non conventional gases: development potential, stakes for the world gas trade, consequence for gas prices, development opportunities for oil companies and for the transport sector, impact on CO 2 emissions, macro-economic impact in the case of the USA

  2. Thermal maturity and organic composition of Pennsylvanian coals and carbonaceous shales, north-central Texas: Implications for coalbed gas potential

    Energy Technology Data Exchange (ETDEWEB)

    Hackley, Paul C. [U.S. Geological Survey, 956 National Center, Reston, VA 20192 (United States); Guevara, Edgar H.; Hentz, Tucker F. [Bureau of Economic Geology, The University of Texas at Austin, Austin, TX 78713 (United States); Hook, Robert W. [1301 Constant Springs Drive, Austin, TX 78746 (United States)

    2009-01-31

    Thermal maturity was determined for about 120 core, cuttings, and outcrop samples to investigate the potential for coalbed gas resources in Pennsylvanian strata of north-central Texas. Shallow (< 600 m; 2000 ft) coal and carbonaceous shale cuttings samples from the Middle-Upper Pennsylvanian Strawn, Canyon, and Cisco Groups in Archer and Young Counties on the Eastern Shelf of the Midland basin (northwest and downdip from the outcrop) yielded mean random vitrinite reflectance (R{sub o}) values between about 0.4 and 0.8%. This range of R{sub o} values indicates rank from subbituminous C to high volatile A bituminous in the shallow subsurface, which may be sufficient for early thermogenic gas generation. Near-surface (< 100 m; 300 ft) core and outcrop samples of coal from areas of historical underground coal mining in the region yielded similar R{sub o} values of 0.5 to 0.8%. Carbonaceous shale core samples of Lower Pennsylvanian strata (lower Atoka Group) from two deeper wells (samples from {proportional_to} 1650 m; 5400 ft) in Jack and western Wise Counties in the western part of the Fort Worth basin yielded higher R{sub o} values of about 1.0%. Pyrolysis and petrographic data for the lower Atoka samples indicate mixed Type II/Type III organic matter, suggesting generated hydrocarbons may be both gas- and oil-prone. In all other samples, organic material is dominated by Type III organic matter (vitrinite), indicating that generated hydrocarbons should be gas-prone. Individual coal beds are thin at outcrop (< 1 m; 3.3 ft), laterally discontinuous, and moderately high in ash yield and sulfur content. A possible analog for coalbed gas potential in the Pennsylvanian section of north-central Texas occurs on the northeast Oklahoma shelf and in the Cherokee basin of southeastern Kansas, where contemporaneous gas-producing coal beds are similar in thickness, quality, and rank. (author)

  3. The potentiality of hydrocarbon generation of the Jurassic source rocks in Salam-3x well,

    Directory of Open Access Journals (Sweden)

    Mohamed M. El Nady

    2016-03-01

    Full Text Available The present work deals with the identification of the potential and generating capability of oil generation in the Jurassic source rocks in the Salam-3x well. This depending on the organo-geochemical analyses of cutting samples representative of Masajid, Khatatba and Ras Qattara formations, as well as, representative extract samples of the Khatatba and Ras Qattara formations. The geochemical analysis suggested the potential source intervals within the encountered rock units as follows: Masajid Formation bears mature source rocks and have poor to fair generating capability for generating gas (type III kerogen. Khatatba Formation bears mature source rock, and has poor to good generating capability for both oil and gas. Ras Qattara Formation constituting mature source rock has good to very good generating capability for both oil and gas. The burial history modeling shows that the Masajid Formation lies within oil and gas windows; Khatatba and Ras Qattara formations lie within the gas window. From the biomarker characteristics of source rocks it appears that the extract is genetically related as the majority of them were derived from marine organic matters sources (mainly algae deposited under reducing environment and take the direction of increasing maturity and far away from the direction of biodegradation. Therefore, Masajid Formation is considered as effective source rocks for generating hydrocarbons, while Khatatba and Ras Qattara formations are the main source rocks for hydrocarbon accumulations in the Salam-3x well.

  4. Modelling hydrothermal venting in volcanic sedimentary basins: Impact on hydrocarbon maturation and paleoclimate

    Science.gov (United States)

    Iyer, Karthik; Schmid, Daniel W.; Planke, Sverre; Millett, John

    2017-06-01

    Vent structures are intimately associated with sill intrusions in sedimentary basins globally and are thought to have been formed contemporaneously due to overpressure generated by gas generation during thermogenic breakdown of kerogen or boiling of water. Methane and other gases generated during this process may have driven catastrophic climate change in the geological past. In this study, we present a 2D FEM/FVM model that accounts for 'explosive' vent formation by fracturing of the host rock based on a case study in the Harstad Basin, offshore Norway. Overpressure generated by gas release during kerogen breakdown in the sill thermal aureole causes fracture formation. Fluid focusing and overpressure migration towards the sill tips results in vent formation after only few tens of years. The size of the vent depends on the region of overpressure accessed by the sill tip. Overpressure migration occurs in self-propagating waves before dissipating at the surface. The amount of methane generated in the system depends on TOC content and also on the type of kerogen present in the host rock. Generated methane moves with the fluids and vents at the surface through a single, large vent structure at the main sill tip matching first-order observations. Violent degassing takes place within the first couple of hundred years and occurs in bursts corresponding to the timing of overpressure waves. The amount of methane vented through a single vent is only a fraction (between 5 and 16%) of the methane generated at depth. Upscaling to the Vøring and Møre Basins, which are a part of the North Atlantic Igneous Province, and using realistic host rock carbon content and kerogen values results in a smaller amount of methane vented than previously estimated for the PETM. Our study, therefore, suggests that the negative carbon isotope excursion (CIE) observed in the fossil record could not have been caused by intrusions within the Vøring and Møre Basins alone and that a contribution from other regions in the NAIP is also required to drive catastrophic climate change.

  5. Temperature-dependent mid-IR absorption spectra of gaseous hydrocarbons

    International Nuclear Information System (INIS)

    Klingbeil, Adam E.; Jeffries, Jay B.; Hanson, Ronald K.

    2007-01-01

    Quantitative mid-IR absorption spectra (2500-3400 cm -1 ) for 12 pure hydrocarbon compounds are measured at temperatures ranging from 25 to 500 deg. C using an FTIR spectrometer. The hydrocarbons studied are n-pentane, n-heptane, n-dodecane, 2,2,4-trimethyl-pentane (iso-octane), 2-methyl-butane, 2-methyl-pentane, 2,4,4-trimethyl-1-pentene, 2-methyl-2-butene, propene, toluene, m-xylene, and ethylbenzene. Room-temperature measurements of neat hydrocarbon vapor were made with an instrument resolution of both 0.1 and 1 cm -1 (FWHM) to confirm that the high-resolution setting was required only to resolve the propene absorption spectrum while the spectra of the other hydrocarbons could be resolved with 1 cm -1 resolution. High-resolution (0.1 cm -1 ), room-temperature measurements of neat hydrocarbons were made at low pressure (∼1 Torr, 133 Pa) and compared to measurements of hydrocarbon/N 2 mixtures at atmospheric pressure to verify that no pressure broadening could be observed over this pressure range. The temperature was varied between 25 and 500 o C for atmospheric-pressure measurements of hydrocarbon/N 2 mixtures (X hydrocarbon ∼0.06-1.5%) and it was found that the absorption cross section shows simple temperature-dependent behavior for a fixed wavelength over this temperature range. Comparisons with previous FTIR data over a limited temperature range and with high-resolution laser absorption data over a wide temperature range show good agreement

  6. Model Titan atmospheric hydrocarbon analysis by Ion Mobility Spectrometry in dry helium

    International Nuclear Information System (INIS)

    Kojiro, D.R.; Stimac, R.M.; Wernlund, R.F.; Cohen, M.J.

    1990-01-01

    Ion Mobility Spectrometry (IMS) is one analytical technique being investigated for the in situ analysis of the atmosphere of Titan. Any hydrocarbon ions that may form react immediately, in microseconds, with the high concentration of water vapor normally present in conventional IMS. By reducing the water concentration to the parts-per-billion range, the lifetime of the hydrocarbon ions may be increased to the milliseconds required for measurement. At low water level concentrations, other species may become the reactant ion. This study focuses on IMS analysis of expected Titan atmospheric hydrocarbons under very dry, low water concentration conditions

  7. Academic Achievement of High School Students in Relation to Their Anxiety, Emotional Maturity and Social Maturity

    Science.gov (United States)

    Puar, Surjit Singh

    2013-01-01

    The present study has been designed to investigate the non-cognitive variables like anxiety, emotional maturity and social maturity and their relationship with academic achievement and also to see the locale-wise differences on the basis of their anxiety, emotional maturity and social maturity. The study was conducted over a sample of 400 (200…

  8. Total organic carbon, an important tool in a holistic approach to hydrocarbon source fingerprinting

    International Nuclear Information System (INIS)

    Boehm, P.D.; Burns, W.A.; Page, D.S.; Bence, A.E.; Mankiewicz, P.J.; Brown, J.S.; Douglas, G.S.

    2002-01-01

    Total organic carbon (TOC) was used to verify the consistency of source allocation results for the natural petrogenic hydrocarbon background of the northern Gulf of Alaska and Prince William Sound where the Exxon Valdez oil spill occurred in 1998. The samples used in the study were either pre-spill sediments or from the seafloor outside the spill path. It is assumed that the natural petrogenic hydrocarbon background in the area comes from either seep oil residues and shale erosion including erosion from petroleum source rock shales, or from coals including those of the Bering River coalfields. The objective of this study was to use the TOC calculations to discriminate between the two very different sources. TOC can constrain the contributions of specific sources and rule out incorrect source allocations, particularly when inputs are dominated by fossil organic carbon. The benthic sediments used in this study showed excellent agreement between measured TOC and calculated TOC from hydrocarbon fingerprint matches of polycyclic aromatic hydrocarbons (PAH) and chemical biomarkers. TOC and fingerprint matches confirmed that TOC sources were properly identified. The matches quantify the hydrocarbon contributions of different sources to the benthic sediments and the degree of hydrocarbon winnowing by waves and currents. It was concluded that the natural petrogenic hydrocarbon background in the sediments in the area comes from eroding Tertiary shales and oil seeps along the northern Gulf of Alaska coast. Thermally mature area coals are excluded from being important contributors to the background at Prince William Sound because of their high TOC content. 26 refs., 4 figs

  9. Total organic carbon, an important tool in a holistic approach to hydrocarbon source fingerprinting

    Energy Technology Data Exchange (ETDEWEB)

    Boehm, P.D. [Battelle, Waltham, MA (United States); Burns, W.A. [W.A. Burns Consulting Services, Houston, TX (United States); Page, D.S. [Bowdoin College, Brunswick, ME (United States); Bence, A.E.; Mankiewicz, P.J. [ExxonMobil Upstream Research Co., Houston, TX (United States); Brown, J.S.; Douglas, G.S. [Battelle, Duxbury, MA (United States)

    2002-07-01

    Total organic carbon (TOC) was used to verify the consistency of source allocation results for the natural petrogenic hydrocarbon background of the northern Gulf of Alaska and Prince William Sound where the Exxon Valdez oil spill occurred in 1998. The samples used in the study were either pre-spill sediments or from the seafloor outside the spill path. It is assumed that the natural petrogenic hydrocarbon background in the area comes from either seep oil residues and shale erosion including erosion from petroleum source rock shales, or from coals including those of the Bering River coalfields. The objective of this study was to use the TOC calculations to discriminate between the two very different sources. TOC can constrain the contributions of specific sources and rule out incorrect source allocations, particularly when inputs are dominated by fossil organic carbon. The benthic sediments used in this study showed excellent agreement between measured TOC and calculated TOC from hydrocarbon fingerprint matches of polycyclic aromatic hydrocarbons (PAH) and chemical biomarkers. TOC and fingerprint matches confirmed that TOC sources were properly identified. The matches quantify the hydrocarbon contributions of different sources to the benthic sediments and the degree of hydrocarbon winnowing by waves and currents. It was concluded that the natural petrogenic hydrocarbon background in the sediments in the area comes from eroding Tertiary shales and oil seeps along the northern Gulf of Alaska coast. Thermally mature area coals are excluded from being important contributors to the background at Prince William Sound because of their high TOC content. 26 refs., 4 figs.

  10. Maturity models in supply chain sustainability

    DEFF Research Database (Denmark)

    Correia, Elisabete; Carvalho, Helena; Azevedo, Susana G.

    2017-01-01

    A systematic literature review of supply chain maturity models with sustainability concerns is presented. The objective is to give insights into methodological issues related to maturity models, namely the research objectives; the research methods used to develop, validate and test them; the scope...... of maturity levels. The comprehensive review, analysis, and synthesis of the maturity model literature represent an important contribution to the organization of this research area, making possible to clarify some confusion that exists about concepts, approaches and components of maturity models...

  11. Bioremediation of petroleum hydrocarbons in soil: Activated sludge treatability study

    International Nuclear Information System (INIS)

    Rue-Van Es, J.E. La.

    1993-05-01

    Batch activated sludge treatability studies utilizing petroleum hydrocarbon contaminated soils (diesel oil and leaded gasoline) were conducted to determine: initial indigenous biological activity in hydrocarbon-contaminated soils; limiting factors of microbiological growth by investigating nutrient addition, chemical emulsifiers, and co-substrate; acclimation of indigenous population of microorganisms to utilize hydrocarbons as sole carbon source; and temperature effects. Soil samples were taken from three different contaminated sites and sequencing batch reactors were run. Substrate (diesel fuel) and nutrient were added as determined by laboratory analysis of orthophosphate, ammonia nitrogen, chemical oxygen demand, and total organic carbon. Substrate was made available to the bacterial mass by experimenting with four different chemical emulsifiers. Indigenous microorganisms capable of biotransforming hydrocarbons seem to be present in all the contaminated soil samples received from all sites. Microscopic analysis revealed no visible activity at the beginning of the study and presence of flagellated protozoa, paramecium, rotifers, and nematodes at the end of the year. Nutrient requirements and the limiting factors in microorganism growth were determined for each site. An emulsifier was initially necessary to make the substrate available to the microbial population. Decreases in removal were found with lowered temperature. Removal efficiencies ranged from 50-90%. 95 refs., 11 figs., 13 tabs

  12. Formaldehyde, methanol and hydrocarbon emissions from methanol-fueled cars

    International Nuclear Information System (INIS)

    Williams, R.L.; Lipari, F.; Potter, R.A.

    1990-01-01

    Exhaust and evaporative emissions tests were conducted on several methanol- and gasoline-fueled vehicles. Separate samples for chromatographic analysis of formaldehyde, methanol, and individual hydrocarbons were collected in each of the three phases of the driving cycle and in each of the two portions of the evaporative emissions test. One vehicle, equipped with an experimental variable-fuel engine, was tested using methanol/gasoline fuel mixtures of 100, 85, 50, 15, and 0 percent methanol. Combustion-generated hydrocarbons were lowest using methanol fuel, and increased several-fold as the gasoline fraction was increased. Gasoline components in the exhaust increased from zero as the gasoline fraction of the fuel was increased. On the other hand, formaldehyde emissions were several times higher using methanol fuel than they were using gasoline. A dedicated methanol car and the variable-fuel car gave similar emissions patterns when they both were tested using methanol fuel. The organic-carbon composition of the exhaust was 85-90 percent methanol, 5-7 percent formaldehyde, and 3-9 percent hydrocarbons. Several cars that were tested using gasoline emitted similar distributions of hydrocarbons, even through the vehicles represented a broad range of current and developmental engine families and emissions control systems

  13. Bioremediation of petroleum hydrocarbons in soil: Activated sludge treatability study

    Energy Technology Data Exchange (ETDEWEB)

    Rue-Van Es, J.E. La.

    1993-05-01

    Batch activated sludge treatability studies utilizing petroleum hydrocarbon contaminated soils (diesel oil and leaded gasoline) were conducted to determine: initial indigenous biological activity in hydrocarbon-contaminated soils; limiting factors of microbiological growth by investigating nutrient addition, chemical emulsifiers, and co-substrate; acclimation of indigenous population of microorganisms to utilize hydrocarbons as sole carbon source; and temperature effects. Soil samples were taken from three different contaminated sites and sequencing batch reactors were run. Substrate (diesel fuel) and nutrient were added as determined by laboratory analysis of orthophosphate, ammonia nitrogen, chemical oxygen demand, and total organic carbon. Substrate was made available to the bacterial mass by experimenting with four different chemical emulsifiers. Indigenous microorganisms capable of biotransforming hydrocarbons seem to be present in all the contaminated soil samples received from all sites. Microscopic analysis revealed no visible activity at the beginning of the study and presence of flagellated protozoa, paramecium, rotifers, and nematodes at the end of the year. Nutrient requirements and the limiting factors in microorganism growth were determined for each site. An emulsifier was initially necessary to make the substrate available to the microbial population. Decreases in removal were found with lowered temperature. Removal efficiencies ranged from 50-90%. 95 refs., 11 figs., 13 tabs.

  14. Hydrocarbon Reserves: Abundance or Scarcity

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    IFP and the OAPEC jointly organize a regular international seminar dealing with world oil-related problems appearing in the news. For the first time, this seminar has been opened to oil and gas company specialists, service companies, research centers and independents. This year's theme concerns oil and gas reserves: are they abundant or are we headed towards the shortages announced by some experts? This theme is especially topical in that: oil and gas currently meet two thirds of world energy needs and almost completely dominate the transport sector; the reserves declared by the OAPEC countries account for nearly half of world reserves; the price of a barrel of oil went through the roof in 2004; world energy demand is growing fast and alternative sources of energy are far from ready to take over from oil and gas in the next few decades. Since the reserves correspond to the volume it is technically and economically viable to produce, the seminar has, of course, dealt with the technical and economic questions that arise in connection with exploration and production, but it has also considered changes in the geopolitical context. Presentations by the leading companies of the OAPEC countries and by the IFP group were completed by presentation from the International Energy Agency (IEA), the United States Geological Survey (USGS), the IHS Energy Group, Total and Gaz de France. This document gathers the transparencies of the following presentations: Hydrocarbon reserves in OAPEC members countries: current and future (M. Al-Lababidi); Non OAPEC liquid reserves and production forecasts (Y. Mathieu); World oil and gas resources and production outlook (K. Chew); Global investments in the upstream (F. Birol); Total's policy in the oil and gas sector (C. de Margerie); Gaz de France's policy in the oil and gas sector (J. Abiteboul); NOC/IOC's opportunities in OPEC countries (I. Sandrea); Relationships between companies, countries and investors: How they may impact on the growth

  15. Hydrocarbon Reserves: Abundance or Scarcity

    International Nuclear Information System (INIS)

    2005-01-01

    IFP and the OAPEC jointly organize a regular international seminar dealing with world oil-related problems appearing in the news. For the first time, this seminar has been opened to oil and gas company specialists, service companies, research centers and independents. This year's theme concerns oil and gas reserves: are they abundant or are we headed towards the shortages announced by some experts? This theme is especially topical in that: oil and gas currently meet two thirds of world energy needs and almost completely dominate the transport sector; the reserves declared by the OAPEC countries account for nearly half of world reserves; the price of a barrel of oil went through the roof in 2004; world energy demand is growing fast and alternative sources of energy are far from ready to take over from oil and gas in the next few decades. Since the reserves correspond to the volume it is technically and economically viable to produce, the seminar has, of course, dealt with the technical and economic questions that arise in connection with exploration and production, but it has also considered changes in the geopolitical context. Presentations by the leading companies of the OAPEC countries and by the IFP group were completed by presentation from the International Energy Agency (IEA), the United States Geological Survey (USGS), the IHS Energy Group, Total and Gaz de France. This document gathers the transparencies of the following presentations: Hydrocarbon reserves in OAPEC members countries: current and future (M. Al-Lababidi); Non OAPEC liquid reserves and production forecasts (Y. Mathieu); World oil and gas resources and production outlook (K. Chew); Global investments in the upstream (F. Birol); Total's policy in the oil and gas sector (C. de Margerie); Gaz de France's policy in the oil and gas sector (J. Abiteboul); NOC/IOC's opportunities in OPEC countries (I. Sandrea); Relationships between companies, countries and investors: How they may impact on the growth

  16. Hydrocarbon Reserves: Abundance or Scarcity

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    IFP and the OAPEC jointly organize a regular international seminar dealing with world oil-related problems appearing in the news. For the first time, this seminar has been opened to oil and gas company specialists, service companies, research centers and independents. This year's theme concerns oil and gas reserves: are they abundant or are we headed towards the shortages announced by some experts? This theme is especially topical in that: oil and gas currently meet two thirds of world energy needs and almost completely dominate the transport sector; the reserves declared by the OAPEC countries account for nearly half of world reserves; the price of a barrel of oil went through the roof in 2004; world energy demand is growing fast and alternative sources of energy are far from ready to take over from oil and gas in the next few decades. Since the reserves correspond to the volume it is technically and economically viable to produce, the seminar has, of course, dealt with the technical and economic questions that arise in connection with exploration and production, but it has also considered changes in the geopolitical context. Presentations by the leading companies of the OAPEC countries and by the IFP group were completed by presentation from the International Energy Agency (IEA), the United States Geological Survey (USGS), the IHS Energy Group, Total and Gaz de France. This document gathers the transparencies of the following presentations: Hydrocarbon reserves in OAPEC members countries: current and future (M. Al-Lababidi); Non OAPEC liquid reserves and production forecasts (Y. Mathieu); World oil and gas resources and production outlook (K. Chew); Global investments in the upstream (F. Birol); Total's policy in the oil and gas sector (C. de Margerie); Gaz de France's policy in the oil and gas sector (J. Abiteboul); NOC/IOC's opportunities in OPEC countries (I. Sandrea); Relationships between companies, countries and investors: How they may

  17. Assessment of polycyclic aromatic hydrocarbons (PAHs) pollution in soil of suburban areas in Tianjin, China.

    Science.gov (United States)

    Lv, Jungang; Shi, Rongguang; Cai, Yanming; Liu, Yong

    2010-07-01

    Soil contamination with polycyclic aromatic hydrocarbons is an increasing problem and has aroused more and more concern in many countries, including China. In this study, representative soil samples (n = 87) of suburban areas in Tianjin (Xiqing, Dongli, Jinnan, Beichen) were evaluated for 16 polycyclic aromatic hydrocarbons. Surface soil samples were air-dried and sieved. Microwave assisted extraction was used for polycyclic aromatic hydrocarbons preparation prior to analysis with gas chromatography-mass spectrometry. The total concentrations of tested polycyclic aromatic hydrocarbons in Xiqing, Dongli, Jinnan, Beichen ranged in 58.5-2,748.3, 36.1-6,734.7, 58.5-4,502.5, 29.7-852.5 ng/g and the averages of total concentration of polycyclic aromatic hydrocarbons were 600.5, 933.6, 640.8, 257.3 ng/g, respectively. Spatial variation of polycyclic aromatic hydrocarbons in soil was illustrated; Pollution status and comparison to other cities were also investigated. Serious polycyclic aromatic hydrocarbons soil pollution was found in Dongli district, on the contrary, Bap in most sites in Beichen did not exceed relative standards and most sites in Beichen should be classified as non-contaminated soil. Principal component analysis was used to identify the possible sources of different districts. It turned out that coal combustion still was the most important sources in three districts except Beichen. Coking, traffic, cooking, biomass combustion also accounted for polycyclic aromatic hydrocarbons pollution to certain extent in different districts. These data can be further used to assess the health risk associated with soils polluted with polycyclic aromatic hydrocarbons and help local government find proper way to reduce polycyclic aromatic hydrocarbons pollution in soils.

  18. Process and catalysts for hydrocarbon conversion. [high antiknock motor fuel

    Energy Technology Data Exchange (ETDEWEB)

    1940-02-14

    High anti-knock motor fuel is produced from hydrocarbons by subjecting it at an elevated temperature to contact with a calcined mixture of hydrated silica, hydrated alumina, and hydrated zirconia, substantially free from alkali metal compounds. The catalyst may be prepared by precipitating silica gel by the acidification of an aqueous solution of an alkali metal silicate, intimately mixing hydrated alumina and hydrated zirconia therewith, drying, purifying the composite to substantially remove alkali metal compounds, again drying, forming the dried material into particles, and finally calcining. The resultant conversion products may be fractionated to produce gasoline, hydrocarbon oil above gasoling boiling point range, and a gaseous fraction of olefins which are polymerized into gasoline boiling range polymers.

  19. Maturity Models Development in IS Research

    DEFF Research Database (Denmark)

    Lasrado, Lester Allan; Vatrapu, Ravi; Andersen, Kim Normann

    2015-01-01

    Maturity models are widespread in IS research and in particular, IT practitioner communities. However, theoretically sound, methodologically rigorous and empirically validated maturity models are quite rare. This literature review paper focuses on the challenges faced during the development...... literature reveals that researchers have primarily focused on developing new maturity models pertaining to domain-specific problems and/or new enterprise technologies. We find rampant re-use of the design structure of widely adopted models such as Nolan’s Stage of Growth Model, Crosby’s Grid, and Capability...... Maturity Model (CMM). Only recently have there been some research efforts to standardize maturity model development. We also identify three dominant views of maturity models and provide guidelines for various approaches of constructing maturity models with a standard vocabulary. We finally propose using...

  20. INFLUENCE MATURATION OF VEAL ON THE MICROBIOLOGICAL AND PHYSICAL INDICATORS

    Directory of Open Access Journals (Sweden)

    Simona Kunová

    2015-06-01

    Full Text Available The aim of the present study was to evaluate microbial and pH changes in veal meat during maturation. Total viable counts, coliform bacteria and pH changes in chilling meat were evaluated after 24 hours, 7 days and 14 days of meat maturation. There were analysed 8 samples of veal meeat. Results of microbiological analysis were compared with Commission regulation (EC No 2073/2005 on microbiological criteria for foodstuffs. Total viable counts (TVC in samples after 24 hours of chilling ranged from 2.02 log CFU.cm-to 4.21 log CFU.cm-2 (1.64 . 104 CFU.cm-2. The average number of TVC after 24 hours of meat maturation was 3.27 log CFU.cm-2, coliform bacteria (CB after 24 hours were lower than than 1 log cfu.cm-2 in five samples, and the highest number of coliform bacteria was 1.65 log cfu.cm-2, average number of CB was 1.13 log cfu.cm-2. pH values in samples after 24 hours of maturation were in range from 6.6 to 7.0, average pH value was 6.8. TVC in samples after 7 days of chilling ranged from 3.09 log CFU.cm-2 to 4.01 log CFU.cm-2, the average number of TVC after 7 days of storage was 3.39 log CFU.cm-2. CB after 7 days of meat maturation were lower than 1 log CFU cm-2 in three samples, the highest value of CB was 2.07 log CFU cm-2, the average value of CB in samples after 7 days of meat chilling was 1.03 log CFU cm-2. pH values of meat after 7 days of maturation ranged from 5.5 to 6.1. The average pH value of samples after 7 days of storage was 5.73 pH values of meat after 14 days of maturation ranged from 6.0 to 6.4. The average pH value of samples after 14 days of storage was 6.16.

  1. A lack of cerebral lateralization in schizophrenia is within the normal variation in brain maturation but indicates late, slow maturation.

    Science.gov (United States)

    Saugstad, L F

    1999-10-19

    The planum temporale (PT) bias, PT leftward, PT symmetry, and PT rightward reversal and sidedness preference, consistent right-handedness, ambilaterality, and consistent left-handedness are placed on a continuum mirroring the normal variation in rate of brain maturation. Maturational rate declines as we pass from PT leftward bias and consistent right-handedness to PT reversal and consistent left-handedness. Concomitantly, we expect an increased prevalence of males due to their pubertal age being about 2 years later than that of females, and a shift in cognitive profile from higher verbal scores than performance scores on the WAIS to higher performance than verbal scores. Three disorders fulfilling the criteria of late CNS maturation apart from the corresponding cognitive profile were studied: infantile autism (IA), schizophrenia (S), and developmental dyslexia (DD). These disorders have in common deficits in cognition, perception, and somatomotor function. The deficits range from an arrest in brain development (which is evident in infancy superimposed on late maturation in IA) to overall delayed brain and somatic development in S (culminating in postpubertal psychotic episodes and persistent and generalized residual deficits). Finally, reading inability, problems in perception (vision and hearing) and in motor coordination, particularly between the two hemispheres, characterize DD. Enhancing brain maturation and the prevalence of 'normal' cerebral asymmetry--laterality is preferable if we want to reduce the risk of developing the above-mentioned disorders. It is suggested that in the past environmental challenges have favored early maturation, with its abundant neuronal population, arborization and excessive density of synapses and cerebral excitability which has powered evolution through the mechanism of natural selection. Early maturation is obtainable through optimal nutrition, including a satisfactory amount of marine fat (PUFA), before and during pregnancy and

  2. Polycyclic aromatic hydrocarbons in some grounded coffee brands.

    Science.gov (United States)

    Grover, Inderpreet Singh; Sharma, Rashmi; Singh, Satnam; Pal, Bonamali

    2013-08-01

    Potentially toxic 16 priority polycyclic aromatic hydrocarbons (PAHs) were determined in four brands of grounded coffee. Four to 13 PAHs were detected. Concentrations of total PAHs in different brands of coffee samples were in the range of 831.7-1,589.7 μg/kg. Benzo[a]pyrene (2A: probable human carcinogen) was found in Nescafe Premium whereas naphthalene (2B: possible human carcinogen) was found in all the samples of coffee.

  3. Distribution Pattern of Polyaromatic Hydrocarbons (PAHs) in Soils in ...

    African Journals Online (AJOL)

    Distribution Pattern of Polyaromatic Hydrocarbons (PAHs) in Soils in the Vicinity of Fuel Stations in Abraka, Nigeria. ... (0.00191mg.kg-1). Investigation also reveals that all tested samples are contaminated, with mean values ranging between 0.000207±0.00026mg.kg-1 and 0.002123±0.00303mg.kg-1. Similarly, spearmen's ...

  4. Analysis of some aromatic hydrocarbons in a benzene-soluble bitumen from Green River shale

    Energy Technology Data Exchange (ETDEWEB)

    Anders, D.E.; Doolittle, F.G.; Robinson, W.E.

    1973-01-01

    The hydrocarbon content of an aromatic fraction, isolated from the bitumen of Green River shale, was studied by mass spectrometry, infra-red spectrometry, gas chromatography and a dehydrogenation technique. The hydrocarbon types and their distribution in this aromatic fraction, as determined by mass spectrometry, are presented. The carbon-number range, empirical formulas and quantity of each compound in the major types are reported. Mass spectra of several compounds and homologous mixtures of compounds isolated from the aromatic fraction are also given.

  5. Soil Iodine Determination in Deccan Syneclise, India: Implications for Near Surface Geochemical Hydrocarbon Prospecting

    International Nuclear Information System (INIS)

    Mani, Devleena; Kumar, T. Satish; Rasheed, M. A.; Patil, D. J.; Dayal, A. M.; Rao, T. Gnaneshwar; Balaram, V.

    2011-01-01

    The association of iodine with organic matter in sedimentary basins is well documented. High iodine concentration in soils overlying oil and gas fields and areas with hydrocarbon microseepage has been observed and used as a geochemical exploratory tool for hydrocarbons in a few studies. In this study, we measure iodine concentration in soil samples collected from parts of Deccan Syneclise in the west central India to investigate its potential application as a geochemical indicator for hydrocarbons. The Deccan Syneclise consists of rifted depositional sites with Gondwana–Mesozoic sediments up to 3.5 km concealed under the Deccan Traps and is considered prospective for hydrocarbons. The concentration of iodine in soil samples is determined using ICP-MS and the values range between 1.1 and 19.3 ppm. High iodine values are characteristic of the northern part of the sampled region. The total organic carbon (TOC) content of the soil samples range between 0.1 and 1.3%. The TOC correlates poorly with the soil iodine (r 2 < 1), indicating a lack of association of iodine with the surficial organic matter and the possibility of interaction between the seeping hydrocarbons and soil iodine. Further, the distribution pattern of iodine compares well with two surface geochemical indicators: the adsorbed light gaseous hydrocarbons (methane through butane) and the propane-oxidizing bacterial populations in the soil. The integration of geochemical observations show the occurrence of elevated values in the northern part of the study area, which is also coincident with the presence of exposed dyke swarms that probably serve as conduits for hydrocarbon microseepage. The corroboration of iodine with existing geological, geophysical, and geochemical data suggests its efficacy as one of the potential tool in surface geochemical exploration of hydrocarbons. Our study supports Deccan Syneclise to be promising in terms of its hydrocarbon prospects.

  6. Triassic oils and related hydrocarbon kitchens in the Adriatic basin

    Energy Technology Data Exchange (ETDEWEB)

    Novelli, L.; Demaison, G. (AGIP, Milan (Italy))

    1988-08-01

    Without exception, the oils from both the Abruzzi basin and Albanian foredeep are of lower Liassic to Upper Triassic origin. This is demonstrated by biological marker-based correlations between the oils and stratigraphically controlled, carbonate-rich source rocks. The biomarker studies also provided proof to conclude that many of the oils possess low API gravities and high sulfur contents because they are immature rather than biodegraded. Following the geochemical investigations, a computer-aided, basinwise maturation simulation of the hydrocarbon kitchens was carried out, with backstripping in geologic time. The simulations, performed with the Tissot-Espitalie kinetic model, used basin-specific kerogen activation energies obtained by the optimum method. These simulated values were calibrated with observed values in deep wells. Two characteristics diverge from normal petroleum basin situations (e.g., the North Sea basin): sulfur-rich kerogens in the source rocks, featuring relatively low activation energy distributions, and low geothermal gradients in the subsurface. The geographic outlines of simulated Triassic-lower Liassic hydrocarbon kitchens closely coincide with the zones of petroleum occurrence and production in the Adriatic basin. Furthermore, API gravities of the oils are broadly predicted by the mathematical simulations. This methodology has once again shown its ability to rationally high-grade the petroleum-rich sectors of sedimentary basin while identifying those areas where chances of success are extremely low regardless of the presence of structures.

  7. Magnetic graphene oxide as adsorbent for the determination of polycyclic aromatic hydrocarbon metabolites in human urine.

    Science.gov (United States)

    Zhu, Linli; Xu, Hui

    2014-09-01

    Detection of monohydroxy polycyclic aromatic hydrocarbons metabolites in urine is an advisable and valid method to assess human environmental exposure to polycyclic aromatic hydrocarbons. In this work, novel Fe3O4/graphene oxide composites were prepared and their application in the magnetic solid-phase extraction of monohydroxy polycyclic aromatic hydrocarbons in urine was investigated by coupling with liquid chromatography and mass spectrometry. In the hybrid material, superparamagnetic Fe3O4 nanoparticles provide fast separation to simplify the analytical process and graphene oxide provides a large functional surface for the adsorption. The prepared magnetic nanocomposites were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and vibrating sample magnetometry. The experimental conditions were optimized systematically. Under the optimal conditions, the recoveries of these compounds were in the range of 98.3-125.2%, the relative standard deviations ranged between 6.8 and 15.5%, and the limits of detection were in the range of 0.01-0.15 ng/mL. The simple, quick, and affordable method was successfully used in the analysis of human urinary monohydroxy polycyclic aromatic hydrocarbons in two different cities. The results indicated that the monohydroxy polycyclic aromatic hydrocarbons level in human urine can provide useful information for environmental exposure to polycyclic aromatic hydrocarbons. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Halogenated hydrocarbons - an environmental problem

    Energy Technology Data Exchange (ETDEWEB)

    Schoeler, H F; Thofern, E

    1984-01-01

    The paper provides a survey of the incidence of highly volatile halogenated hydrocarbons in ground, surface and drinking water as well as in the snows of Western Germany. Almost the entire production of chlorinated solvents is released into the environment. The absorption media are mostly soil, water and atmosphere. Whereas in the atmosphere elimination reactions take place, solvents that have passed the soil get into the ground water owing to their persistence and can cause considerable pollutions of drinking water. Moreover haloforms may occur in drinking water, which are produced during chlorine disinfection of pre-treated water.

  9. Catalytic treatment of hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    1940-02-23

    A process is described for increasing the octane number of a hydrocarbon oil. The substance is subjected under pressure to a temperature between 800 and 1100/sup 0/C. Catalysts include metal compounds of Groups IV, V, Vi, or VIII (Group VI is perferred). Experiments are performed under a hydrogen atmosphere. Reaction time, temperature, pressure, and partial pressure of the hydrogen are adjusted so that there will be no net hydrogen consumption. The reaction gases (including the products) are recycled in whole or in part to supply the hydrogen gas required.

  10. Performance of a Throttle Cycle Refrigerator with Nitrogen-Hydrocarbon and Argon-Hydrocarbon Mixtures

    Science.gov (United States)

    Venkatarathnam, G.; Senthil Kumar, P.; Srinivasa Murthy, S.

    2004-06-01

    Throttle cycle refrigerators are a class of vapor compression refrigerators that can provide refrigeration at cryogenic temperatures and operate with refrigerant mixtures. The performance of our prototype refrigerators with nitrogen-hydrocarbon, nitrogen-hydrocarbon-helium and argon-hydrocarbon refrigerant mixtures is presented in this paper.

  11. Maturity group classification and maturity locus genotyping of early-maturing soybean varieties from high-latitude cold regions.

    Science.gov (United States)

    Jia, Hongchang; Jiang, Bingjun; Wu, Cunxiang; Lu, Wencheng; Hou, Wensheng; Sun, Shi; Yan, Hongrui; Han, Tianfu

    2014-01-01

    With the migration of human beings, advances of agricultural sciences, evolution of planting patterns and global warming, soybeans have expanded to both tropical and high-latitude cold regions (HCRs). Unlike other regions, HCRs have much more significant and diverse photoperiods and temperature conditions over seasons or across latitudes, and HCR soybeans released there show rich diversity in maturity traits. However, HCR soybeans have not been as well classified into maturity groups (MGs) as other places. Therefore, it is necessary to identify MGs in HCRs and to genotype the maturity loci. Local varieties were collected from the northern part of Northeast China and the far-eastern region of Russia. Maturity group reference (MGR) soybeans of MGs MG000, MG00, and MG0 were used as references during field experiments. Both local varieties and MGR soybeans were planted for two years (2010-2011) in Heihe (N 50°15', E 127°27', H 168.5 m), China. The days to VE (emergence), R1 (beginning bloom) and R7 (beginning maturity) were recorded and statistically analyzed. Furthermore, some varieties were further genotyped at four molecularly-identified maturity loci E1, E2, E3 and E4. The HCR varieties were classified into MG0 or even more early-maturing. In Heihe, some varieties matured much earlier than MG000, which is the most early-maturing known MG, and clustered into a separate group. We designated the group as MG0000, following the convention of MGs. HCR soybeans had relatively stable days to beginning bloom from emergence. The HCR varieties diversified into genotypes of E1, E2, E3 and E4. These loci had different effects on maturity. HCRs diversify early-maturing MGs of soybean. MG0000, a new MG that matures much earlier than known MGs, was developed. HCR soybean breeding should focus more on shortening post-flowering reproductive growth. E1, E2, E3, and E4 function differentially.

  12. Selection of bacteria with hydrocarbon degrading capacity isolated from Colombian Caribbean sediments

    International Nuclear Information System (INIS)

    Narvaez Florez, Silvia; Gomez, Martha L; Martinez Maria M

    2008-01-01

    Thirty one bacterial isolations in minimal salts supplemented medium with hydrocarbons (ACPM or crude oil) as sole carbon source were isolated from sediment samples from the Colombian Caribbean. Bacterial strains underwent selection tests in different concentrations of hydrocarbons; 11 tolerant crude oil and ACPM strains in a range of 1-8%v/v were chosen. A mixed bacterial culture was created and assessed its ability to degrade hydrocarbons in a laboratory-scale test, with a concentration of 2% v/v of ACPM over a period of 21 days. Measurements of biomass in Colony Forming Units (CFU)/mL were used to develop the growth curve of the mixed culture. Hydrocarbons remotion was measured by mass chromatography. The mixed culture was able to degrade the 68.6% of aliphatic hydrocarbons in preference of long chain n- alkenes (C12- C31), reaching a maximum growth of 3.13 x 10 9 UFC / mL. Degradation of aromatic hydrocarbons was not evidenced under the observation time. Nine of the eleven strains were identified using the biochemical systems BBL and API 50 CHB/E; they belonged to the genus Klebsiella, Chromobacterium, Flavimonas, Enterobacter,Pseudomonas, and Bacillus. The evaluated strains have enzymatic potential to degrade hydrocarbons and it is necessary to characterize them at molecular level in order to develop and effective consortium for field application

  13. Aliphatic hydrocarbons in surface sediments from South China Sea off Kuching Division, Sarawak

    International Nuclear Information System (INIS)

    Hafidz Yusoff; Zaini Assim; Samsur Mohamad

    2012-01-01

    Eighteen surface sediment samples collected from South China Sea off Kuching Division, Sarawak were analyzed for aliphatic hydrocarbons. These hydrocarbons were recovered from sediment by Soxhlet extraction method and then analyzed using gas chromatography equipped with mass spectrometer (GC/ MS). Total concentrations of aliphatic hydrocarbons in surface sediments from South China Sea off Kuching division are ranged from 35.6 μg/ g to 1466.1 μg/ g dry weights. The sediments collected from Bako Bay, Kuching showed high concentrations of total aliphatic hydrocarbons. Several molecular indices were used to predict the predominant sources of hydrocarbons. Carbon preference index (CPI) value revealed widespread anthropogenic input in this study area (CPI= 0 to 4.1). The ratio of C 31 / C 19 and C 29 / C 31 indicated that major input of aliphatic hydrocarbon mostly transfer by lateral input to the marine environment than atmospheric movements. Generally, the concentrations of aliphatic hydrocarbons in sediment from South China Sea off Kuching division are generally higher compare to other area in the world. (author)

  14. Ambient aromatic hydrocarbon measurements at Welgegund, South Africa

    Science.gov (United States)

    Jaars, K.; Beukes, J. P.; van Zyl, P. G.; Venter, A. D.; Josipovic, M.; Pienaar, J. J.; Vakkari, V.; Aaltonen, H.; Laakso, H.; Kulmala, M.; Tiitta, P.; Guenther, A.; Hellén, H.; Laakso, L.; Hakola, H.

    2014-07-01

    Aromatic hydrocarbons are associated with direct adverse human health effects and can have negative impacts on ecosystems due to their toxicity, as well as indirect negative effects through the formation of tropospheric ozone and secondary organic aerosol, which affect human health, crop production and regional climate. Measurements of aromatic hydrocarbons were conducted at the Welgegund measurement station (South Africa), which is considered to be a regionally representative background site. However, the site is occasionally impacted by plumes from major anthropogenic source regions in the interior of South Africa, which include the western Bushveld Igneous Complex (e.g. platinum, base metal and ferrochrome smelters), the eastern Bushveld Igneous Complex (platinum and ferrochrome smelters), the Johannesburg-Pretoria metropolitan conurbation (> 10 million people), the Vaal Triangle (e.g. petrochemical and pyrometallurgical industries), the Mpumalanga Highveld (e.g. coal-fired power plants and petrochemical industry) and also a region of anticyclonic recirculation of air mass over the interior of South Africa. The aromatic hydrocarbon measurements were conducted with an automated sampler on Tenax-TA and Carbopack-B adsorbent tubes with heated inlet for 1 year. Samples were collected twice a week for 2 h during daytime and 2 h during night-time. A thermal desorption unit, connected to a gas chromatograph and a mass selective detector was used for sample preparation and analysis. Results indicated that the monthly median (mean) total aromatic hydrocarbon concentrations ranged between 0.01 (0.011) and 3.1 (3.2) ppb. Benzene levels did not exceed the local air quality standard limit, i.e. annual mean of 1.6 ppb. Toluene was the most abundant compound, with an annual median (mean) concentration of 0.63 (0.89) ppb. No statistically significant differences in the concentrations measured during daytime and night-time were found, and no distinct seasonal patterns were

  15. The maturity of Nuclear Law

    International Nuclear Information System (INIS)

    Martinez Favini, J.A.

    1985-01-01

    The ever-increasing use of atomic energy since 1950 has generated a set of rules called for practical reasons Nuclear Law. This branch of law covers a wide scope of related activities and, specialized studies have apparently foreseen all conceivable hypotheses. The international character of Nuclear Law explains the basic harmony of international legislation. The methods of comparative Law and International Private Law as well as the joint, indepth work of scientists and jurists will bring about steady progress towards legislative unity and prompt solution to conflicts. The expectable revitalization of nuclear-electric programs early in the 21st. century will give rise to a Nuclear juridical community which can already be perceived through the maturity Nuclear Law has reached. (Author) [es

  16. Decontamination of hydrocarbon contaminated soil

    International Nuclear Information System (INIS)

    Smith, A.J.

    1991-01-01

    This patent describes the method of treating hydrocarbon contaminated soil. It comprises forming the soil into a flowing particulate stream, forming an aqueous liquid mixture of water and treating substance that reacts with hydrocarbon to form CO 2 and water, dispersing the liquid mixture into the particulate soil stream to wet the particulate, allowing the substance to react with the wetted soil particulate to thereby form CO 2 and water, thereby the resultant soil is beneficially treated, the stream being freely projected to dwell at a level and then fall, and the dispersing includes spraying the liquid mixture into the projected stream at the dwell, the substance consisting of natural bacteria, and at a concentration level in the mixture of between 100 to 3,000 PPM of bacteria to water, the soil forming step including impacting the soil to reduce it to particles less than about 1 inches in cross dimension, and including forming the wetting particulate into a first layer on a surface to allow the substance to react

  17. Hydrocarbon production with nuclear explosives

    International Nuclear Information System (INIS)

    Wade Watkins, J.

    1970-01-01

    The tremendous energy of nuclear explosives and the small dimensions of the explosive package make an ideal combination for drill-hole explosive emplacement in deep, thick hydrocarbon deposits. Potential applications exist in fracturing low permeability natural-gas and petroleum formations for stimulating production, fracturing oil shale to permit in situ retorting, and creating storage chimneys for natural gas, liquefied petroleum gas, petroleum, petroleum products, helium, and other fluids. Calculations show, for example, that less than 100 shots per year would be needed to stabilize the natural gas reserves to production ratio. Under the Government-industry Plowshare program, two experiments, Projects Gasbuggy and Rulison, were conducted to stimulate natural gas production from low-permeability formations. Incomplete information indicates that both were technically successful. Potential problems associated with the use of nuclear explosives for underground engineering applications are radioactive contamination, maximum yield limitations, high costs of detonating contained nuclear explosives, and adverse public opinion. Results at Project Gasbuggy and other considerations indicated that the problem of radioactive contamination was about as predicted and not an insurmountable one. Also, it was demonstrated that shots at adequate depths could be detonated without appreciable damage to existing surface and subsurface buildings, natural features, and equipment. However, costs must be reduced and the public must be better informed before these techniques can be widely used in field operations. On the basis of present knowledge, the potential of nuclear-explosive stimulation of hydrocarbon production appears good. Additional field experiments will be required to adequately explore that potential. (author)

  18. Hydrocarbon production with nuclear explosives

    Energy Technology Data Exchange (ETDEWEB)

    Wade Watkins, J [Petroleum Research, Bureau of Mines, U.S. Department of the Interior, Washington, DC (United States)

    1970-05-01

    The tremendous energy of nuclear explosives and the small dimensions of the explosive package make an ideal combination for drill-hole explosive emplacement in deep, thick hydrocarbon deposits. Potential applications exist in fracturing low permeability natural-gas and petroleum formations for stimulating production, fracturing oil shale to permit in situ retorting, and creating storage chimneys for natural gas, liquefied petroleum gas, petroleum, petroleum products, helium, and other fluids. Calculations show, for example, that less than 100 shots per year would be needed to stabilize the natural gas reserves to production ratio. Under the Government-industry Plowshare program, two experiments, Projects Gasbuggy and Rulison, were conducted to stimulate natural gas production from low-permeability formations. Incomplete information indicates that both were technically successful. Potential problems associated with the use of nuclear explosives for underground engineering applications are radioactive contamination, maximum yield limitations, high costs of detonating contained nuclear explosives, and adverse public opinion. Results at Project Gasbuggy and other considerations indicated that the problem of radioactive contamination was about as predicted and not an insurmountable one. Also, it was demonstrated that shots at adequate depths could be detonated without appreciable damage to existing surface and subsurface buildings, natural features, and equipment. However, costs must be reduced and the public must be better informed before these techniques can be widely used in field operations. On the basis of present knowledge, the potential of nuclear-explosive stimulation of hydrocarbon production appears good. Additional field experiments will be required to adequately explore that potential. (author)

  19. Unsaturated medium hydrocarbons pollution evaluation

    International Nuclear Information System (INIS)

    Di Luise, G.

    1991-01-01

    When the so called porous unsaturated medium, that's the vertical subsoil section between both the ground and water-table level, is interested by a hydrocarbons spill, the problem to evaluate the pollution becomes difficult: considering, essentially, the natural coexistence in it of two fluids, air and water, and the interactions between them. This paper reports that the problems tend to increase when a third fluid, the pollutant, immiscible with water, is introduced into the medium: a three-phases flow, which presents several analogies with the flow conditions present in an oil-reservoir, will be established. In such a situation, it would be very useful to handle the matter by the commonly used parameters in the oil reservoirs studies such as: residual saturation, relative permeability, phases mobility, to derive a first semiquantitative estimation of the pollution. The subsoil pollution form hydrocarbons agents is one of the worldwide more diffused causes of contamination: such events are generally referable to two main effects: accidental (oil pipeline breakdowns, e.g.), and continuous (underground tanks breaks, industrial plants leakages, e.g.)

  20. Production of hydrogen from hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Lohmueller, R

    1984-03-01

    Hydrocarbons are the preferred starting materials for the industrial production of hydrogen. Most hydrogen is produced by steam reforming of light hydrocarbons. Partial oxidation of heavy oil and residue is used for the production of H/sub 2/ and synthesis gas in large plants. In both cases gas purification was improved. Hydrogen-rich gases like coke oven gas, refinery-offgas, and offgases from the chemical and petrochemical industry have high potential for becoming a major source of hydrogen. Processes for recovering H/sub 2/ (and by-products) are condensation and rectification at low temperatures and, most attractive and versatile for the production of very pure H/sub 2/, adsorption (PSA). The environmental impact of H/sub 2/ production lies mainly in the emission of CO/sub 2/ and heat. Other forms of pollution can be considerably reduced by conventional methods. The economy of H/sub 2/ production depends essentially on price and availability of the raw materials.

  1. The electrostatic atomization of hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, A J

    1984-06-01

    Exploitation of the unique and potentially beneficial characteristics of electrostatic atomization in combustion systems has foundered upon the inability of two element, diode devices to operate at flow rates that are larger than a fraction of a millilitre per second. This restriction has been attributed to the high innate electrical resistivity of hydrocarbon fuels. A discussion of proposed electrostatic fuel atomizers and their limitations is presented from the vantage of a recently developed theory of electrostatic spraying. Comparison of theory and experiment reveals the existence of a 'constant of spraying' and the presence of an operational regime in which low charge density droplet development is possible. Operation with hydrocarbons in this regime occurs when the mean droplet size is greater than or equal to 10 ..mu..m and fluid viscosity is below about 250 cp. The resulting spray has a mean droplet size that is functionally dependent only upon the free charge density level of the fluid. Consequently there is no theoretical impediment to the attainment of high flow rate electrostatic atomization with fluids of arbitrary conductivity. Implementation is achieved by a general class of electrostatic spray devices which employ direct charge injection. The Spray Triode, a submerged field-emission electron gun, represents a particularly simple member of this new class of atomizer. Among the Spray Triode operational characteristics to be discussed is insensitivity to spray fluid properties and flow rate.

  2. Alternatives of applications in the information taking with artificial radioactive tools in the mature fields of the South region

    International Nuclear Information System (INIS)

    Fuentes, J.L.

    2005-01-01

    In this work it is widely described the application of the saturation control tool (RST) used in the campo Rodador (Mexico), and shortly the registration tools of location monitoring (RMT) and the Monitor tool of the location operation (RPM) used for the evaluation in site of the mature wells, had being at the present time these three tools with nuclear reaction mechanisms to obtain the water saturation and of hydrocarbon by means of the Neutron capture (PNC) and Inelastic scattering (IS). Both tools have been designed to help to the evaluation of the mature wells in the locations. Starting from measurements made through the lining pipe applying nuclear techniques used by these tools of registrations to derive the water saturation and of hydrocarbon. In this work the basic principles of radioactivity and their application in the radioactive tools are described as well as the operative aspects of the tools before mentioned, some practical applications of the saturation control tool are presented and a technical study of cost-benefit and it is shown as the technology advances have allowed to carry out considerable progresses in the taking of information of the mature wells helping by this way, to build better geological models in the locations that help to increase the hydrocarbon production in wells that have many years of exploitation. (Author)

  3. A maturity model for blockchain adoption

    OpenAIRE

    Wang, Huaiqing; Chen, Kun; Xu, Dongming

    2016-01-01

    Background: The rapid development of the blockchain technology and its various applications has rendered it important to understand the guidelines for adopting it. Methods: The comparative analysis method is used to analyze different dimensions of the maturity model, which is mainly based on the commonly used capability maturity model. Results: The blockchain maturity model and its adoption process have been discussed and presented. Conclusions: This study serves as a guide to institutions to...

  4. A Set Theoretical Approach to Maturity Models

    DEFF Research Database (Denmark)

    Lasrado, Lester; Vatrapu, Ravi; Andersen, Kim Normann

    2016-01-01

    characterized by equifinality, multiple conjunctural causation, and case diversity. We prescribe methodological guidelines consisting of a six-step procedure to systematically apply set theoretic methods to conceptualize, develop, and empirically derive maturity models and provide a demonstration......Maturity Model research in IS has been criticized for the lack of theoretical grounding, methodological rigor, empirical validations, and ignorance of multiple and non-linear paths to maturity. To address these criticisms, this paper proposes a novel set-theoretical approach to maturity models...

  5. Primary biodegradation of petroleum hydrocarbons in seawater

    Energy Technology Data Exchange (ETDEWEB)

    Comber, M.I.H.; Den Haan, K.H.; Djemel, N.; Eadsforth, C.V.; King, D.; Paumen, M.L.; Parkerton, T.; Dmytrasz, B.

    2012-12-15

    This report describes primary biodegradation experiments performed to determine the persistence of higher molecular weight petroleum hydrocarbons in seawater. Results from the biodegradation experiments show that the majority of tested petroleum hydrocarbons have half-lives in seawater less than 60 days.

  6. Mechanistic model for microbial growth on hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Mallee, F M; Blanch, H W

    1977-12-01

    Based on available information describing the transport and consumption of insoluble alkanes, a mechanistic model is proposed for microbial growth on hydrocarbons. The model describes the atypical growth kinetics observed, and has implications in the design of large scale equipment for single cell protein (SCP) manufacture from hydrocarbons. The model presents a framework for comparison of the previously published experimental kinetic data.

  7. Molecular characterization of autochthonous hydrocarbon utilizing ...

    African Journals Online (AJOL)

    Prof. Ogunji

    Materials and Methods ... culturable hydrocarbon utilizing bacteria (HUB) were enumerated by vapour phase ... hydrocarbon utilizing bacterial isolates by boiling method according to ... obtained in this investigation are consistent with past field studies (Kostka et ... Microbial and other related changes in a Niger sediment.

  8. Versatility of hydrocarbon production in cyanobacteria.

    Science.gov (United States)

    Xie, Min; Wang, Weihua; Zhang, Weiwen; Chen, Lei; Lu, Xuefeng

    2017-02-01

    Cyanobacteria are photosynthetic microorganisms using solar energy, H 2 O, and CO 2 as the primary inputs. Compared to plants and eukaryotic microalgae, cyanobacteria are easier to be genetically engineered and possess higher growth rate. Extensive genomic information and well-established genetic platform make cyanobacteria good candidates to build efficient biosynthetic pathways for biofuels and chemicals by genetic engineering. Hydrocarbons are a family of compounds consisting entirely of hydrogen and carbon. Structural diversity of the hydrocarbon family is enabled by variation in chain length, degree of saturation, and rearrangements of the carbon skeleton. The diversified hydrocarbons can be used as valuable chemicals in the field of food, fuels, pharmaceuticals, nutrition, and cosmetics. Hydrocarbon biosynthesis is ubiquitous in bacteria, yeasts, fungi, plants, and insects. A wide variety of pathways for the hydrocarbon biosynthesis have been identified in recent years. Cyanobacteria may be superior chassis for hydrocabon production in a photosynthetic manner. A diversity of hydrocarbons including ethylene, alkanes, alkenes, and terpenes can be produced by cyanobacteria. Metabolic engineering and synthetic biology strategies can be employed to improve hydrocarbon production in cyanobacteria. This review mainly summarizes versatility and perspectives of hydrocarbon production in cyanobacteria.

  9. 33 CFR 157.166 - Hydrocarbon emissions.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Hydrocarbon emissions. 157.166 Section 157.166 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.166 Hydrocarbon emissions. If the...

  10. Hydrocarbon formation mechanism during uranium monocarbide hydrolysis

    International Nuclear Information System (INIS)

    Ermolaev, M.I.; Tishchenko, G.V.

    1979-01-01

    The hydrolysis of uranium monocarbide in oxidative media and in the presence of excessive hydrogen in statu nascendi has been investigated. It was found that oxydants promote the formation of elementary carbon, while in the presence of hydrogen the yield of light C-C hydrocarbons increases. EPR data confirm the radical mechanism of hydrocarbons formation during the decomposition of uranium monocarbide

  11. George A. Olah, Carbocation and Hydrocarbon Chemistry

    Science.gov (United States)

    dropdown arrow Site Map A-Z Index Menu Synopsis George A. Olah, Carbocation and Hydrocarbon Chemistry George Olah received the 1994 Nobel Prize in Chemistry "for his contribution to carbocation chemistry" and his 'role in the chemistry of hydrocarbons. In particular, he developed superacids

  12. Analysis of carbon stable isotope to determine the origin and migration of gaseous hydrocarbon in the Brazilian sedimentary basins

    International Nuclear Information System (INIS)

    Takaki, T.; Rodrigues, R.

    1986-01-01

    The carbon isotopic composition of natural gases to determine the origin and gaseous hydrocarbon migration of Brazilian sedimentar basins is analysed. The carbon isotopic ratio of methane from natural gases depends on the process of gas formation and stage of organic matter maturation. In the geochemical surface exploration the biogenic gases are differentiated from thermogenic gases, because the last one is isotopically heavier. As the isotopic composition of methane has not changed during migration, the migrated gases from deeper and more mature source rocks are identified by its relative 13 C enrichment. The methane was separated from chromatography and and the isotopic analysis was done with mass spectrometer. (M.C.K.) [pt

  13. The distribution and sources of polycyclic aromatic hydrocarbons in shallow groundwater from an alluvial-diluvial fan of the Hutuo River in North China

    Science.gov (United States)

    Wang, Jincui; Zhao, Yongsheng; Sun, Jichao; Zhang, Ying; Liu, Chunyan

    2018-06-01

    This paper has investigated the concentration and distribution of polycyclic aromatic hydrocarbons in shallow groundwater from an alluvial-diluvial fan of the Hutuo River in North China. Results show that the concentration levels of 16 priority polycyclic aromatic hydrocarbons range from 0 to 92.06 ng/L, do not conform to drinking water quality standards in China (GB 5749- 2006). However, the concentration figures of priority polycyclic aromatic hydrocarbons are much lower than that of other studies conducted elsewhere in China. In addition, highly-concentrated polycyclic aromatic hydrocarbons (50-92 ng/L) are fragmentarily distributed. The composition of polycyclic aromatic hydrocarbons from this study indicates that low molecular polycyclic aromatic hydrocarbons are predominant in groundwater samples, medium molecular compounds occur at low concentrations, and high molecular hydrocarbons are not detected. The polycyclic aromatic hydrocarbon composition in groundwater samples is basically the same as that of gaseous samples in the atmosphere in this study. Therefore, the atmospheric input is assumed to be an important source of polycyclic aromatic hydrocarbons, no less than wastewater discharge, adhesion on suspended solids, and surface water leakage. Ratios of specific polycyclic aromatic hydrocarbons demonstrate that they mainly originate from wood or coal combustion as well as natural gas and partially from petroleum according to the result of principal component analysis. On the whole, conclusions are drawn that the contamination sources of these polycyclic aromatic hydrocarbons are likely petrogenic and pyrolytic inputs. Future investigations by sampling topsoil, vadose soil, and the atmosphere can further verify aforementioned conclusions.

  14. Algal Lipid Extraction and Upgrading to Hydrocarbons Technology Pathway

    Energy Technology Data Exchange (ETDEWEB)

    Davis, Ryan; Biddy, Mary J.; Jones, Susanne B.

    2013-03-31

    In support of the Bioenergy Technologies Office, the National Renewable Energy Laboratory (NREL) and the Pacific Northwest National Laboratory (PNNL) are undertaking studies of biomass conversion technologies to identify barriers and target research toward reducing conversion costs. Process designs and preliminary economic estimates for each of these pathway cases were developed using rigorous modeling tools (Aspen Plus and Chemcad). These analyses incorporated the best information available at the time of development, including data from recent pilot and bench-scale demonstrations, collaborative industrial and academic partners, and published literature and patents. This technology pathway case investigates the cultivation of algal biomass followed by further lipid extraction and upgrading to hydrocarbon biofuels. Technical barriers and key research needs have been assessed in order for the algal lipid extraction and upgrading pathway to be competitive with petroleum-derived gasoline, diesel and jet range hydrocarbon blendstocks.

  15. Biological Conversion of Sugars to Hydrocarbons Technology Pathway

    Energy Technology Data Exchange (ETDEWEB)

    Davis, Ryan; Biddy, Mary J.; Tan, Eric; Tao, Ling; Jones, Susanne B.

    2013-03-31

    In support of the Bioenergy Technologies Office, the National Renewable Energy Laboratory (NREL) and the Pacific Northwest National Laboratory (PNNL) are undertaking studies of biomass conversion technologies to identify barriers and target research toward reducing conversion costs. Process designs and preliminary economic estimates for each of these pathway cases were developed using rigorous modeling tools (Aspen Plus and Chemcad). These analyses incorporated the best information available at the time of development, including data from recent pilot and bench-scale demonstrations, collaborative industrial and academic partners, and published literature and patents. This technology pathway case investigates the biological conversion of biomass derived sugars to hydrocarbon biofuels, utilizing data from recent literature references and information consistent with recent pilot scale demonstrations at NREL. Technical barriers and key research needs have been identified that should be pursued for the pathway to become competitive with petroleum-derived gasoline, diesel and jet range hydrocarbon blendstocks.

  16. Autothermal reforming of liquid hydrocarbons for H{sub 2} production

    Energy Technology Data Exchange (ETDEWEB)

    Palm, C.; Montel, S.; Cremer, P.; Peters, R.; Stolten, D. [Forschungszentrum Juelich GmbH (Germany). Inst. for Materials and Processes in Energy Systems IWV-3: Process Engineering

    2001-07-01

    The process of autothermal reforming of hydrocarbons can be used for the production of hydrogen within a fuel cell system. The application of three precious metal catalysts for the autothermal reforming of alkane mixtures with boiling ranges between 235 and 325 C was examined. The experiments were carried out at n(O{sub 2})/n(C) = 0.40, n(H{sub 2}O)/n(C) = 2.20, a catalyst bed temperature between 730 and 570 C and a hydrocarbon feed of 30 g/h. The catalysts yielded different hydrocarbon conversions, which can be explained by differences in the activity for the steam reforming reaction. The most active catalyst was also successfully utilized in the conversion of 400 g/h hydrocarbon feed. (orig.)

  17. Polycyclic aromatic hydrocarbons and heavy metals in the Cispata Bay, Colombia: A marine tropical ecosystem.

    Science.gov (United States)

    Burgos-Núñez, Saudith; Navarro-Frómeta, Amado; Marrugo-Negrete, José; Enamorado-Montes, Germán; Urango-Cárdenas, Iván

    2017-07-15

    The concentrations of polycyclic aromatic hydrocarbons and heavy metals were evaluated in shallow sediments, water, fish and seabird samples from the Cispata Bay, Colombia. The heavy metals concentrations in the sediment was in the following order: Cu>Pb>Hg>Cd. The heavy metal concentration was different (ppolycyclic aromatic hydrocarbons ranged from 7.0-41ngg -1 in sediment, 0.03-0.34ngmL -1 in water samples, 53.24ngg -1 in fish, and 66ngg -1 in seabirds. The high concentrations of heavy metals in seabirds may be explained by their feeding habits. The presence of polycyclic aromatic hydrocarbons in the Cispata Bay may be due to hydrocarbon spills during oil transport at the nearby oil port. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Total petroleum hydrocarbons in edible marine biota from Northern Persian Gulf.

    Science.gov (United States)

    Nozar, Seyedeh Laili Mohebbi; Pauzi, Mohamad Zakaria; Salarpouri, Ali; Daghooghi, Behnam; Salimizadeh, Maryam

    2015-04-01

    To provide a baseline information for consumer's health, distribution of total petroleum hydrocarbons in 18 edible marine biota species from northern Persian Gulf was evaluated. The samples were purchased from fish market of Hormozgan Province, South of Iran. Marine biota samples included different species with various feeding habits and were analyzed based on ultraviolet florescence spectroscopy. Petroleum hydrocarbons showed narrow variation, ranging from 0.67 to 3.36 μg/g dry weight. The maximum value was observed in silver pomfret. Anchovy and silver pomfret with the highest content of petroleum hydrocarbons were known as good indicator for oil pollution in the studied area. From public health point of view, the detected concentrations for total petroleum hydrocarbons were lower than hazardous guidelines. The results were recorded as background data and information in the studied area; the continuous monitoring of pollutants is recommended, according to the rapid extension of industrial and oily activities in Hormozgan Province.

  19. Determination of chlorinated polycyclic aromatic hydrocarbons in water by solid-phase extraction coupled with gas chromatography and mass spectrometry.

    Science.gov (United States)

    Wang, Xianli; Kang, Haiyan; Wu, Junfeng

    2016-05-01

    Given the potential risks of chlorinated polycyclic aromatic hydrocarbons, the analysis of their presence in water is very urgent. We have developed a novel procedure for determining chlorinated polycyclic aromatic hydrocarbons in water based on solid-phase extraction coupled with gas chromatography and mass spectrometry. The extraction parameters of solid-phase extraction were optimized in detail. Under the optimal conditions, the proposed method showed wide linear ranges (1.0-1000 ng/L) with correlation coefficients ranging from 0.9952 to 0.9998. The limits of detection and the limits of quantification were in the range of 0.015-0.591 and 0.045-1.502 ng/L, respectively. Recoveries ranged from 82.5 to 102.6% with relative standard deviations below 9.2%. The obtained method was applied successfully to the determination of chlorinated polycyclic aromatic hydrocarbons in real water samples. Most of the chlorinated polycyclic aromatic hydrocarbons were detected and 1-monochloropyrene was predominant in the studied water samples. This is the first report of chlorinated polycyclic aromatic hydrocarbons in water samples in China. The toxic equivalency quotients of chlorinated polycyclic aromatic hydrocarbons in the studied tap water were 9.95 ng the toxic equivalency quotient m(-3) . 9,10-Dichloroanthracene and 1-monochloropyrene accounted for the majority of the total toxic equivalency quotients of chlorinated polycyclic aromatic hydrocarbons in tap water. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Upgrading of syngas hydrotreated fractionated oxidized bio-oil to transportation grade hydrocarbons

    International Nuclear Information System (INIS)

    Luo, Yan; Hassan, El Barbary; Guda, Vamshi; Wijayapala, Rangana; Steele, Philip H.

    2016-01-01

    Highlights: • Hydrotreating of fractionated oxidized bio-oil with syngas was feasible. • Hydrocarbon properties were similar with all syngas H_2/CO molar ratios except viscosity. • Syngas with H_2/CO molar ratio of (4:6) produced the highest hydrocarbon yield. • The produced hydrocarbons were in the range of gasoline, jet fuel and diesel boiling points. - Abstract: Fast pyrolysis bio-oils have the potential to replace a part of transportation fuels obtained from fossil. Bio-oil can be successfully upgraded into stable hydrocarbons (gasoline, jet fuel and diesel) through a two-stage hydrodeoxygenation process. Consumption large amount of expensive hydrogen during this process is the major hurdle for commercialization of this technology. Applying syngas in the hydrotreating step can significantly reduce the cost of the whole process and make it competitive. In this study, four different models of syngas with different H_2 concentrations (H_2/CO molar ratios = 2:8, 4:6, 6:4 and 8:2) were used for the 1st-stage hydrotreating step of oxidized fractionated bio-oil (OFB). The 2nd-stage hydrocracking step was performed on the produced organic liquid products (OLPs) by using pure H_2 gas. The effect of syngas H_2 concentrations on the yields and properties of OLPs and the 2nd-stage hydrocarbons (HCs) was investigated. Physical and chemical properties of the 2nd-stage hydrocarbons were similar regardless syngas H_2 content, with the exception of the viscosity. Syngas with H_2/CO molar ratio of 4:6 gave significantly highest HCs yield (24.8 wt.%) based on the OFB. Simulated distillation analysis proved that all 2nd-stage hydrocarbons were mixture from a wide range boiling point fuels. These results also indicated that the successful 1st-stage syngas hydrotreating step was having the potential to produce different hydrocarbons.

  1. Analysis of petroleum hydrocarbons in soil from view of bioremediation process

    International Nuclear Information System (INIS)

    Mracnova, R.; Sojak, L.; Kubinec, R.; Kraus, A.; Eszenyiova, A.; Ostrovsky, I.

    2002-01-01

    The pollution of the environment by petroleum hydrocarbons is the most often pollution of them all. Nevertheless, hydrocarbons present in environment can be not only of petroleum or anthropogenic origin, but of biogenic as well. Typically the hydrocarbons are presented in the environment as very complex mixtures of individual compounds with very different chemical structure, wide range of the boiling points (∼800 0 C) as well as with the wide range of the number of carbon atoms. Immediately they are spread in any environmental matrix the complex physical, chemical and biochemical reactions start. A lot of methods have been developed and new are permanently in progress for the monitoring and control of petroleum hydrocarbons contamination and/or soils bioremediation. Generally, all methods by whose the hydrocarbons contaminants are determined in GC-FID system do not satisfied recommendations for enough accurate and precise results. Hyphenation of capillary gas chromatography and mass selective detector operated in the selective ion monitoring mode essentially allows detailed specification of non-polar extractable hydrocarbons. Isoprenoid alkanes, alkylhomologues of aromatic hydrocarbons and polycyclic alkanes hopanes-like were investigated as markers for recognition of petroleum and biogenic contamination. C 30 17α(H)21β(H)-hopane (C 30 -hopane) seems to be a suitable marker to identify hydrocarbons origin, to determine composting rates for nonpolar extractable compounds and to calculate real content of non-polar extractable compounds in final composting status on the assumption that the contamination is of mineral oil type. This is the survey into the results obtained in this field published in the literature as well as reached in our laboratory. (author)

  2. The maturing of microbial ecology.

    Science.gov (United States)

    Schmidt, Thomas M

    2006-09-01

    A.J. Kluyver and C.B. van Niel introduced many scientists to the exceptional metabolic capacity of microbes and their remarkable ability to adapt to changing environments in The Microbe's Contribution to Biology. Beyond providing an overview of the physiology and adaptability of microbes, the book outlined many of the basic principles for the emerging discipline of microbial ecology. While the study of pure cultures was highlighted, provided a unifying framework for understanding the vast metabolic potential of microbes and their roles in the global cycling of elements, extrapolation from pure cultures to natural environments has often been overshadowed by microbiologists inability to culture many of the microbes seen in natural environments. A combination of genomic approaches is now providing a culture-independent view of the microbial world, revealing a more diverse and dynamic community of microbes than originally anticipated. As methods for determining the diversity of microbial communities become increasingly accessible, a major challenge to microbial ecologists is to link the structure of natural microbial communities with their functions. This article presents several examples from studies of aquatic and terrestrial microbial communities in which culture and culture-independent methods are providing an enhanced appreciation for the microbe's contribution to the evolution and maintenance of life on Earth, and offers some thoughts about the graduate-level educational programs needed to enhance the maturing field of microbial ecology.

  3. Motivational maturity and helping behavior.

    Science.gov (United States)

    Haymes, M; Green, L

    1977-12-01

    This study was undertaken to examine the independent influences of conative development (the Maslow needs hierarchy) upon behavioral aspects of prosocial orientations. It provides a behavioral demonstration of conative effects in a helping paradigm, among college-age men. A comparison of the conative data across the ages of 15-22 provided a cross-sectional view of conative development itself. Conative maturity was found to be predictive of greater helping among college-age men. Situational demands were demonstrated which tended to mask, but not override, these predispositional influences on helping. The cross-sectional data on conative development point to probable movement to early esteem concerns among high school men who have reached the conative level of love and belonging. On the other hand, the stability across the years of 15-22 of proportion of safety concerns suggests fixation of such concerns in those exhibiting them in high school. Results are discussed in terms of conative growth for development of prosocial orientations.

  4. Smart Grid Interoperability Maturity Model

    Energy Technology Data Exchange (ETDEWEB)

    Widergren, Steven E.; Levinson, Alex; Mater, J.; Drummond, R.

    2010-04-28

    The integration of automation associated with electricity resources (including transmission and distribution automation and demand-side resources operated by end-users) is key to supporting greater efficiencies and incorporating variable renewable resources and electric vehicles into the power system. The integration problems faced by this community are analogous to those faced in the health industry, emergency services, and other complex communities with many stakeholders. To highlight this issue and encourage communication and the development of a smart grid interoperability community, the GridWise Architecture Council (GWAC) created an Interoperability Context-Setting Framework. This "conceptual model" has been helpful to explain the importance of organizational alignment in addition to technical and informational interface specifications for "smart grid" devices and systems. As a next step to building a community sensitive to interoperability, the GWAC is investigating an interoperability maturity model (IMM) based on work done by others to address similar circumstances. The objective is to create a tool or set of tools that encourages a culture of interoperability in this emerging community. The tools would measure status and progress, analyze gaps, and prioritize efforts to improve the situation.

  5. Antenatal assessment of fetal maturity

    International Nuclear Information System (INIS)

    Gerstner, G.; Reinold, E.; Wolf, G.

    1979-01-01

    334 ultrasound-cephalometries and 231 X-ray fetographies were performed for antenatal assessment of fetal maturity as well as for exact estimation of gestational age in women with unknown date of confinement. The accuracy of the predictions was compared. Ultrasound-cephalometry gave best results when performed until the 20th week of gestation. A correct prediction was obtained in 80.4% of cases. After the 20th week of gestation, the accuracy of prediction decreased. Radiology on the contrary gave optimal results at the end of pregnancy. A correct prediction of the date of confinement was obtained in 73.8% of cases, when the X-ray fetography was performed between the 37th and 40th week of gestation. At the end of gestation radiography should be performed, if there is a discrepancy between ultrasound and clinical estimation or if ultrasound-cephalometry was not carried out in early pregnancy - especially if induction of labour is necessary. (author)

  6. Spheno-Occipital Synchondrosis Fusion Correlates with Cervical Vertebrae Maturation.

    Directory of Open Access Journals (Sweden)

    María José Fernández-Pérez

    Full Text Available The aim of this study was to determine the relationship between the closure stage of the spheno-occipital synchondrosis and the maturational stage of the cervical vertebrae (CVM in growing and young adult subjects using cone beam computed tomography (CBCT. CBCT images with an extended field of view obtained from 315 participants (148 females and 167 males; mean age 15.6 ±7.3 years; range 6 to 23 years were analyzed. The fusion status of the synchondrosis was determined using a five-stage scoring system; the vertebral maturational status was evaluated using a six-stage stratification (CVM method. Ordinal regression was used to study the ability of the synchondrosis stage to predict the vertebral maturation stage. Vertebrae and synchondrosis had a strong significant correlation (r = 0.89 that essential was similar for females (r = 0.88 and males (r = 0.89. CVM stage could be accurately predicted from synchondrosis stage by ordinal regression models. Prediction equations of the vertebral stage using synchondrosis stage, sex and biological age as predictors were developed. Thus this investigation demonstrated that the stage of spheno-occipital synchondrosis, as determined in CBCT images, is a reasonable indicator of growth maturation.

  7. Spheno-Occipital Synchondrosis Fusion Correlates with Cervical Vertebrae Maturation.

    Science.gov (United States)

    Fernández-Pérez, María José; Alarcón, José Antonio; McNamara, James A; Velasco-Torres, Miguel; Benavides, Erika; Galindo-Moreno, Pablo; Catena, Andrés

    2016-01-01

    The aim of this study was to determine the relationship between the closure stage of the spheno-occipital synchondrosis and the maturational stage of the cervical vertebrae (CVM) in growing and young adult subjects using cone beam computed tomography (CBCT). CBCT images with an extended field of view obtained from 315 participants (148 females and 167 males; mean age 15.6 ±7.3 years; range 6 to 23 years) were analyzed. The fusion status of the synchondrosis was determined using a five-stage scoring system; the vertebral maturational status was evaluated using a six-stage stratification (CVM method). Ordinal regression was used to study the ability of the synchondrosis stage to predict the vertebral maturation stage. Vertebrae and synchondrosis had a strong significant correlation (r = 0.89) that essential was similar for females (r = 0.88) and males (r = 0.89). CVM stage could be accurately predicted from synchondrosis stage by ordinal regression models. Prediction equations of the vertebral stage using synchondrosis stage, sex and biological age as predictors were developed. Thus this investigation demonstrated that the stage of spheno-occipital synchondrosis, as determined in CBCT images, is a reasonable indicator of growth maturation.

  8. Photodynamic activity of polycyclic hydrocarbon

    Energy Technology Data Exchange (ETDEWEB)

    Epstein, S S

    1963-01-01

    Exposure of Paramecium caudatum to suspensions of 3,4-benzopyrene, followed by long wave ultraviolet irradiation, results in cell death at times related, inter alia, to carcinogen concentration. Prior to death, the cells exhibit progressive immobilization and blebbing. This photodynamic response is a sensitized photo-oxidation, as it is oxygen-dependent and inhibited by anti-oxidants, such as butylated hydroxy anisole and ..cap alpha..-tocopherol. Protection is also afforded by other agents, including Tweens, tryptophan and certain fractions of plasma proteins. No evidence was found for the involvement of peroxides or sulfhydryl groups. The correlations between photodynamic toxicity and carcinogenicity in a large series of polycyclic hydrocarbons is under investigation. Assays of air extracts for photodynamic toxicity are in progress. Significant toxicity has been found in oxygenated besides aromatic fractions.

  9. Digital Maturity of the Firm's Business Model

    DEFF Research Database (Denmark)

    Groskovs, Sergejs; Vemula, Sreekanth

    We propose a digital maturity assessment model as an instrument for researchers and a strategic tool for managers. Existing literature lacks a conceptually clear way to measure the construct of digital maturity at the level of the firms business model. Our proposed instrument thus opens avenues f...

  10. A maturity model for industrial supply chains

    NARCIS (Netherlands)

    Hameri, A.P.; McKay, K.N.; Wiers, V.C.S.

    2013-01-01

    This article takes an evolutionary view of supply chains to suggest a series of distinct, contextual phases for supply chain execution and what maturity might mean at each phase. For example, what is best practice in a mature industry might not be best practice in a pioneering situation.Three

  11. 7 CFR 1421.101 - Maturity dates.

    Science.gov (United States)

    2010-01-01

    ... filed and disbursed except, for transferred marketing assistance loan collateral. The maturity date for transferred marketing assistance loan collateral will be the maturity date applicable to the original loan... AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS GRAINS AND SIMILARLY HANDLED COMMODITIES-MARKETING...

  12. Cone and Seed Maturation of Southern Pines

    Science.gov (United States)

    James P. Barnett

    1976-01-01

    If slightly reduced yields and viability are acceptable, loblolly and slash cone collections can begin 2 to 3 weeks before maturity if the cones are stored before processing. Longleaf(P. palestris Mill.) pine cones should be collected only when mature, as storage decreased germination of seeds from immature cones. Biochemical analyses to determine reducing sugar...

  13. POSTTREATMENT NEUROBLASTOMA MATURATION TO GANGLIONIC CELL TUMOR

    Directory of Open Access Journals (Sweden)

    M. V. Ryzhova

    2012-01-01

    Full Text Available Tumor cells can differentiate into more mature forms in undifferentiated or poorly differentiated tumors, such as medulloblastomas with increased nodularity, as well as neuroblastomas. The authors describe 2 cases of neuroblastoma maturation into ganglioneuroblastoma 5 months after chemotherapy in a 2-year-old girl and 3 years after radiotherapy in a 16-year-old girl.

  14. Moving towards maturity in business model definitions

    DEFF Research Database (Denmark)

    Nielsen, Christian; Lund, Morten; Bukh, Per Nikolaj

    2014-01-01

    The field of business models has, as is the case with all emerging fields of practice, slowly matured through the development of frameworks, models, concepts and ideas over the last 15 years. New concepts, theories and models typically transcend a series of maturity phases. For the concept of Bus...

  15. Assessing the Harvest Maturity of Brazilian Mangoes

    NARCIS (Netherlands)

    Pereira, T.; Tijskens, L.M.M.; Vanoli, M.; Rizzolo, A.; Eccher Zerbini, P.C.; Torricelli, A.; Filgueiras, H.; Spinelli, L.

    2010-01-01

    No clear criterion exists to determine the optimum time to harvest mango. Some empirical relations are used to assess maturity, such as shoulder development. Moreover, as a result of the typical growing conditions in tropical climates, a huge variation in maturity and ripeness exists, seriously

  16. Decision-Making Style and Vocational Maturity.

    Science.gov (United States)

    Phillips, Susan D.; Strohmer, Douglas C.

    1982-01-01

    Examined the relationship between decision-making style, scholastic achievement, and vocational maturity for college students (N=64). Results did not support the hypothesized relationship between rationality and attitudinal and cognitive maturity. Scholastic achievement and lack of dependent decision style were found to be moderately predictive of…

  17. Correlation of Improved Version of Cervical Vertebral Maturation Indicator with Other Growth Maturity Indicators

    Directory of Open Access Journals (Sweden)

    Tripti Tikku

    2013-01-01

    Conclusion: The correlation between middle phalanx of 3rd finger (MP3 and cervical vertebral maturation method (CVMI and CVMS was higher as compared to the correlation of either of the cervical vertebral maturation method or MP3 with dental maturation indicator.

  18. Assessing healthcare process maturity: challenges of using a business process maturity model

    NARCIS (Netherlands)

    Tarhan, A.; Turetken, O.; van den Biggelaar, F.J.H.M.

    2015-01-01

    Doi: 10.4108/icst.pervasivehealth.2015.259105 The quality of healthcare services is influenced by the maturity of healthcare processes used to develop it. A maturity model is an instrument to assess and continually improve organizational processes. In the last decade, a number of maturity models

  19. Evaluation of mineral oil saturated hydrocarbons (MOSH and mineral oil aromatic hydrocarbons (MOAH in pure mineral hydrocarbon-based cosmetics and cosmetic raw materials using 1H NMR spectroscopy [version 2; referees: 3 approved

    Directory of Open Access Journals (Sweden)

    Dirk W. Lachenmeier

    2017-08-01

    Full Text Available Mineral hydrocarbons consist of two fractions, mineral oil saturated hydrocarbons (MOSH and mineral oil aromatic hydrocarbons (MOAH. MOAH is a potential public health hazard because it may include carcinogenic polycyclic compounds. In the present study, 400 MHz nuclear magnetic resonance (NMR spectroscopy was introduced, in the context of official controls, to measure MOSH and MOAH in raw materials or pure mineral hydrocarbon final products (cosmetics and medicinal products. Quantitative determination (qNMR has been established using the ERETIC methodology (electronic reference to access in vivo concentrations based on the PULCON principle (pulse length based concentration determination. Various mineral hydrocarbons (e.g., white oils, paraffins or petroleum jelly were dissolved in deuterated chloroform. The ERETIC factor was established using a quantification reference sample containing ethylbenzene and tetrachloronitrobenzene. The following spectral regions were integrated: MOSH δ 3.0 – 0.2 ppm and MOAH δ 9.2 - 6.5, excluding solvent signals. Validation showed a sufficient precision of the method with a coefficient of variation <6% and a limit of detection <0.1 g/100 g. The applicability of the method was proven by analysing 27 authentic samples with MOSH and MOAH contents in the range of 90-109 g/100 g and 0.02-1.10 g/100 g, respectively. It is important to distinguish this new NMR-approach from the hyphenated liquid chromatography-gas chromatography methodology previously used to characterize MOSH/MOAH amounts in cosmetic products. For mineral hydrocarbon raw materials or pure mineral hydrocarbon-based cosmetic products, NMR delivers higher specificity without any sample preparation besides dilution. Our sample survey shows that previous methods may have overestimated the MOAH amount in mineral oil products and opens new paths to characterize this fraction. Therefore, the developed method can be applied for routine monitoring of consumer

  20. Set-Theoretic Approach to Maturity Models

    DEFF Research Database (Denmark)

    Lasrado, Lester Allan

    Despite being widely accepted and applied, maturity models in Information Systems (IS) have been criticized for the lack of theoretical grounding, methodological rigor, empirical validations, and ignorance of multiple and non-linear paths to maturity. This PhD thesis focuses on addressing...... these criticisms by incorporating recent developments in configuration theory, in particular application of set-theoretic approaches. The aim is to show the potential of employing a set-theoretic approach for maturity model research and empirically demonstrating equifinal paths to maturity. Specifically...... methodological guidelines consisting of detailed procedures to systematically apply set theoretic approaches for maturity model research and provides demonstrations of it application on three datasets. The thesis is a collection of six research papers that are written in a sequential manner. The first paper...

  1. A statistical approach to the interpretation of aliphatic hydrocarbon distributions in marine sediments

    Science.gov (United States)

    Rapp, J.B.

    1991-01-01

    Q-mode factor analysis was used to quantitate the distribution of the major aliphatic hydrocarbon (n-alkanes, pristane, phytane) systems in sediments from a variety of marine environments. The compositions of the pure end members of the systems were obtained from factor scores and the distribution of the systems within each sample was obtained from factor loadings. All the data, from the diverse environments sampled (estuarine (San Francisco Bay), fresh-water (San Francisco Peninsula), polar-marine (Antarctica) and geothermal-marine (Gorda Ridge) sediments), were reduced to three major systems: a terrestrial system (mostly high molecular weight aliphatics with odd-numbered-carbon predominance), a mature system (mostly low molecular weight aliphatics without predominance) and a system containing mostly high molecular weight aliphatics with even-numbered-carbon predominance. With this statistical approach, it is possible to assign the percentage contribution from various sources to the observed distribution of aliphatic hydrocarbons in each sediment sample. ?? 1991.

  2. Distribution of hydrocarbon-utilizing microorganisms and hydrocarbon biodegradation potentials in Alaskan continental shelf areas

    International Nuclear Information System (INIS)

    Roubal, G.; Atlas, R.M.

    1978-01-01

    Hydrocarbon-utilizing microogranisms were enumerated from Alaskan continental shelf areas by using plate counts and a new most-probable-number procedure based on mineralization of 14 C-labeled hydrocarbons. Hydrocarbon utilizers were ubiquitously distributed, with no significant overall concentration differences between sampling regions or between surface water and sediment samples. There were, however, significant seasonal differences in numbers of hydrocarbon utilizers. Distribution of hydrocarbon utilizers within Cook Inlet was positively correlated with occurrence of hydrocarbons in the environment. Hydrocarbon biodegradation potentials were measured by using 14 C-radiolabeled hydrocarbon-spiked crude oil. There was no significant correlation between numbers of hydrocarbon utilizers and hydrocarbon biodegradation potentials. The biodegradation potentials showed large seasonal variations in the Beaufort Sea, probably due to seasonal depletion of available nutrients. Non-nutrient-limited biodegradation potentials followed the order hexadecane > naphthalene >> pristane > benzanthracene. In Cook Inlet, biodegradation potentials for hexadecane and naphthalene were dependent on availability of inorganic nutrients. Biodegradation potentials for pristane and benzanthracene were restricted, probably by resistance to attack by available enzymes in the indigenous population

  3. Evaluation of abundant hydrocarbon-generation depressions in the deepwater area of Qiongdongnan Basin, South China Sea

    Institute of Scientific and Technical Information of China (English)

    LIU Zhen; SUN Zhipeng; WANG Zisong; ZHANG Wei; LI Tingan; HE Weijun; LI Fengxia

    2016-01-01

    It has been confirmed that the key source rocks of Qiongdongnan Basin are associated with the Yacheng Formation, which was deposited in a transitional marine-continental environment. Because the distribution and evolution patterns of the source rocks in the major depressions are different, it is important to determine the most abundant hydrocarbon-generation depressions in terms of exploration effectiveness. Based on an analysis of organic matter characteristics of the source rocks, in combination with drilling data and seismic data, this paper establishes a model to evaluate the hydrocarbon-generation depressions in the deepwater area of Qiongdongnan Basin. First of all, by using the method of seismic-facies model analysis, the distribution of sedimentary facies was determined. Then, the sedimentary facies were correlated with the organic facies, and the distribution of organic facies was predicted. Meanwhile, the thickness of source rocks for all the depressions was calculated on the basis of a quantitative analysis of seismic velocity and lithology. The relationship between mudstone porosity and vitrinite reflectance (Ro) was used to predict the maturity of source rocks. Second, using the parameters such as thickness and maturity of source rocks, the quantity and intensity of gas generation for Yacheng and Lingshui Formations were calculated. Finally, in combination with the identified hydrocarbon resources, the quantity and intensity of gas generation were used as a guide to establish an evaluation standard for hydrocarbon-generation depressions, which was optimized for the main depressions in the Central Depression Belt. It is proposed that Lingshui, Ledong, Baodao and Changchang Depressions are the most abundant hydrocarbon depressions, whilst Songnan and Beijiao Depressions are rich hydrocarbon depressions. Such an evaluation procedure is beneficial to the next stage of exploration in the deep-water area of Qiongdongnan Basin.

  4. Ambient aromatic hydrocarbon measurements at Welgegund, South Africa

    Energy Technology Data Exchange (ETDEWEB)

    Jaars, K.; Beukes, J. P.; van Zyl, P. G.; Venter, A. D.; Josipovic, M.; Pienaar, J. J.; Vakkari, Ville; Aaltonen, H.; Laakso, H.; Kulmala, M.; Tiitta, P.; Guenther, Alex B.; Hellen, H.; Laakso, L.; Hakola, H.

    2014-07-11

    Aromatic hydrocarbons are associated with direct adverse human health effects and can have negative impacts on ecosystems due to their toxicity, as well as indirect negative effects through the formation of tropospheric ozone and secondary organic aerosol that affect human health, crop production and regional climate. Measurements were conducted at the Welgegund measurement station (South Africa) that is considered to be a regionally representative background site. However, the site is occasionally impacted by plumes from major anthropogenic source regions in the interior of South Africa, which include the western Bushveld Igneous Complex (e.g. platinum, base metal and ferrochrome smelters), the eastern Bushveld Igneous Complex (platinum and ferrochrome smelters), the Johannesburg-Pretoria metropolitan conurbation (>10 million people), the Vaal Triangle (e.g. petrochemical and industries), the Mpumalanga Highveld (e.g. coal-fired power plants and petrochemical industry) and also a region of anti-cyclonic recirculation of air mass over the interior of South Africa. The aromatic hydrocarbon measurements were conducted with an automated sampler on Tenax-TA and Carbopack-B adsorbent tubes with heated inlet for one year. Samples were collected twice a week for two hours during daytime and two hours 1 during night-time. A thermal desorption unit, connected to a gas chromatograph and a mass 2 selective detector was used for sample preparation and analysis. Results indicated that the 3 monthly median total aromatic hydrocarbon concentrations ranged between 0.01 to 3.1 ppb. 4 Benzene levels did not exceed local air quality standards. Toluene was the most abundant 5 species, with an annual median concentration of 0.63 ppb. No statistically significant 6 differences in the concentrations measured during daytime and night-time were found and no distinct seasonal patterns were observed. Air mass back trajectory analysis proved that the lack of seasonal cycles could be

  5. Hydrocarbon pollution from marinas in estuarine sediments

    Science.gov (United States)

    Voudrias, Evangelos A.; Smith, Craig L.

    1986-03-01

    A measure of the impact of marinas on three Eastern Virginia estuarine creeks was obtained by a study of hydrocarbons in their sediments. Two of the creeks support considerable marine activity, including pleasure boat marinas, boat repair facilities, and commercial fishing operations. The third creek, which served as a control, is seldom used by boats, and is surrounded by marsh and woodland. Sediments from the creeks with marinas contained significantly higher levels of both aromatic and aliphatic hydrocarbons than did the control. Differences in the concentrations of certain oil-pollution indicators, such as the 17α,21β-hopane homologs and phytane, and low molecular weight aromatic hydrocarbons, are indicative of light petroleum fractions. Most of the aromatic hydrocarbons from all creeks, however, appear to have a pyrogenic origin. Although hydrocarbons from three probable origins (petroleum, pyrogenesis, and recent biosynthesis) were detected in all locations, the petroleum-derived and pyrogenic hydrocarbons were of only minor importance relative to the biogenic hydrocarbons in the control creek.

  6. Detection of irradiated meats by hydrocarbon method

    International Nuclear Information System (INIS)

    Goto, Michiko; Miyakawa, Hiroyuki; Fujinuma, Kenji; Ozawa, Hideki

    2005-01-01

    Meats, for example, lamb, razorback, wild duck and turkey were irradiated by gamma ray, and the amounts of hydrocarbons formed from fatty acids were measured. Since C 20:0 was found from wild duck and turkey. C 1-18:1 was recommended for internal standard. Good correlation was found between the amount of hydrocarbons and the doses of gamma irradiation. This study shows that such hydrocarbons induced after radiation procedure as C 1,7-16:2 , C 8-17:1 , C 1-14:1 , and C 15:0 may make it possible to detect irradiated lamb, razorback, wild duck and turkey. (author)

  7. Process for recovery of liquid hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Millar, J.F.; Cockshott, J.E.

    1978-04-11

    Methane is recovered as a gas for discharge to a pipeline from a gas stream containing methane and heavier hydrocarbons, principally ethane and propane. Separation is accomplished by condensing the heavier hydrocarbons and distilling the methane therefrom. A liquid product (LPG) comprising the heavier hydrocarbons is subsequently recovered and transferred to storage. Prior to being discharged to a pipeline, the recovered methane gas is compressed and in undergoing compression the gas is heated. The heat content of the gas is employed to reboil the refrigerant in an absorption refrigeration unit. The refrigeration unit is used to cool the LPG prior to its storage.

  8. Method of recovering hydrocarbons from oil shale

    Energy Technology Data Exchange (ETDEWEB)

    Walton, D.K.; Slusser, M.S.

    1970-11-24

    A method is described for recovering hydrocarbons from an oil-shale formation by in situ retorting. A well penetrating the formation is heated and gas is injected until a pressure buildup within the well is reached, due to a decrease in the conductivity of naturally occurring fissures within the formation. The well is then vented, in order to produce spalling of the walls. This results in the formation of an enlarged cavity containing rubberized oil shale. A hot gas then is passed through the rubberized oil shale in order to retort hydrocarbons and these hydrocarbons are recovered from the well. (11 claims)

  9. The offshore hydrocarbon releases (HCR) database

    International Nuclear Information System (INIS)

    Bruce, R.A.P.

    1995-01-01

    Following Cullen Recommendation 39 which states that: ''The regulatory body should be responsible for maintaining a database with regard to hydrocarbon leaks, spills, and ignitions in the Industry and for the benefit of Industry'', HSE Offshore Safety Division (HSE-OSD) has now been operating the Hydrocarbon Releases (HCR) Database for approximately 3 years. This paper deals with the reporting of Offshore Hydrocarbon Releases, the setting up of the HCR Database, the collection of associated equipment population data, and the main features and benefits of the database, including discussion on the latest output information. (author)

  10. Waste Plastic Converting into Hydrocarbon Fuel Materials

    Energy Technology Data Exchange (ETDEWEB)

    Sarker, Moinuddin; Mamunor Rashid, Mohammad; Molla, Mohammad

    2010-09-15

    The increased demand and high prices for energy sources are driving efforts to convert organic compounds into useful hydrocarbon fuels. Although much of this work has focused on biomass, there are strong benefits to deriving fuels from waste plastic material. Natural State Research Inc. (NSR) has invented a simple and economically viable process to decompose the hydrocarbon polymers of waste plastic into the shorter chain hydrocarbon of liquid fuel (patent pending). The method and principle of the production / process will be discussed. Initial tests with several widely used polymers indicate a high potential for commercialization.

  11. New method dynamically models hydrocarbon fractionation

    Energy Technology Data Exchange (ETDEWEB)

    Kesler, M.G.; Weissbrod, J.M.; Sheth, B.V. [Kesler Engineering, East Brunswick, NJ (United States)

    1995-10-01

    A new method for calculating distillation column dynamics can be used to model time-dependent effects of independent disturbances for a range of hydrocarbon fractionation. It can model crude atmospheric and vacuum columns, with relatively few equilibrium stages and a large number of components, to C{sub 3} splitters, with few components and up to 300 equilibrium stages. Simulation results are useful for operations analysis, process-control applications and closed-loop control in petroleum, petrochemical and gas processing plants. The method is based on an implicit approach, where the time-dependent variations of inventory, temperatures, liquid and vapor flows and compositions are superimposed at each time step on the steady-state solution. Newton-Raphson (N-R) techniques are then used to simultaneously solve the resulting finite-difference equations of material, equilibrium and enthalpy balances that characterize distillation dynamics. The important innovation is component-aggregation and tray-aggregation to contract the equations without compromising accuracy. This contraction increases the N-R calculations` stability. It also significantly increases calculational speed, which is particularly important in dynamic simulations. This method provides a sound basis for closed-loop, supervisory control of distillation--directly or via multivariable controllers--based on a rigorous, phenomenological column model.

  12. MODELING GALACTIC EXTINCTION WITH DUST AND 'REAL' POLYCYCLIC AROMATIC HYDROCARBONS

    International Nuclear Information System (INIS)

    Mulas, Giacomo; Casu, Silvia; Cecchi-Pestellini, Cesare; Zonca, Alberto

    2013-01-01

    We investigate the remarkable apparent variety of galactic extinction curves by modeling extinction profiles with core-mantle grains and a collection of single polycyclic aromatic hydrocarbons. Our aim is to translate a synthetic description of dust into physically well-grounded building blocks through the analysis of a statistically relevant sample of different extinction curves. All different flavors of observed extinction curves, ranging from the average galactic extinction curve to virtually 'bumpless' profiles, can be described by the present model. We prove that a mixture of a relatively small number (54 species in 4 charge states each) of polycyclic aromatic hydrocarbons can reproduce the features of the extinction curve in the ultraviolet, dismissing an old objection to the contribution of polycyclic aromatic hydrocarbons to the interstellar extinction curve. Despite the large number of free parameters (at most the 54 × 4 column densities of each species in each ionization state included in the molecular ensemble plus the 9 parameters defining the physical properties of classical particles), we can strongly constrain some physically relevant properties such as the total number of C atoms in all species and the mean charge of the mixture. Such properties are found to be largely independent of the adopted dust model whose variation provides effects that are orthogonal to those brought about by the molecular component. Finally, the fitting procedure, together with some physical sense, suggests (but does not require) the presence of an additional component of chemically different very small carbonaceous grains.

  13. Predicting bioremediation of hydrocarbons: Laboratory to field scale

    International Nuclear Information System (INIS)

    Diplock, E.E.; Mardlin, D.P.; Killham, K.S.; Paton, G.I.

    2009-01-01

    There are strong drivers to increasingly adopt bioremediation as an effective technique for risk reduction of hydrocarbon impacted soils. Researchers often rely solely on chemical data to assess bioremediation efficiently, without making use of the numerous biological techniques for assessing microbial performance. Where used, laboratory experiments must be effectively extrapolated to the field scale. The aim of this research was to test laboratory derived data and move to the field scale. In this research, the remediation of over thirty hydrocarbon sites was studied in the laboratory using a range of analytical techniques. At elevated concentrations, the rate of degradation was best described by respiration and the total hydrocarbon concentration in soil. The number of bacterial degraders and heterotrophs as well as quantification of the bioavailable fraction allowed an estimation of how bioremediation would progress. The response of microbial biosensors proved a useful predictor of bioremediation in the absence of other microbial data. Field-scale trials on average took three times as long to reach the same endpoint as the laboratory trial. It is essential that practitioners justify the nature and frequency of sampling when managing remediation projects and estimations can be made using laboratory derived data. The value of bioremediation will be realised when those that practice the technology can offer transparent lines of evidence to explain their decisions. - Detailed biological, chemical and physical characterisation reduces uncertainty in predicting bioremediation.

  14. Early retention of 237Pu + 239Pu in mature beagles

    International Nuclear Information System (INIS)

    Lloyd, R.D.; McFarland, S.S.; Atherton, D.R.; Bruenger, F.W.; Taylor, G.N.; Mays, C.W.

    1978-01-01

    Five mature beagles, ranging in age from 57 to 84 months, were injected intravenously with about 0.05-0.1 μCi/kg of 239 Pu(IV) citrate to which tracer amounts of the photon-emitter 237 Pu had been added. Plutonium retention in liver and in non-liver tissue (mainly skeleton) was measured periodically in the living dogs for nearly 4 months after injection by a combination of total-body and partial-body counting. All excreta were collected during the first 21 days and analysed for their Pu content. One dog was sacrificed at 14 days and another at 118 days for distribution studies. About 17% (14-20%) of the injected Pu was excreted in the urine and feces in the first 3 weeks, about the same as that excreted in a corresponding time by beagles injected as young adults (14%), but substantially more than beagles injected as juveniles (11%). In contrasts to juvenile beagles injected at 3 months of age, in which early retention was about 12% in liver and 68% in the skeleton, mature beagles retained about 30% in liver and 50% in the skeleton. Retention in young adult beagles injected at 17 months of age was similar to that of mature dogs. Relative distribution of skeletal plutonium among various bones was similar in the mature animals to that seen previously in young adults, but quite different from that of juveniles. A notable exception was the humerus for which there was no significant difference (P>0.2) in the % of retained skeletal Pu represented by the humerus among the juvenile, young adult and mature dogs. (author)

  15. Petrology, palynology and organic geochemistry of Eocene lignite of Matanomadh, Kutch Basin, western India: Implications to depositional environment and hydrocarbon source potential

    Energy Technology Data Exchange (ETDEWEB)

    Dutta, Suryendu; Mathews, Runcie P.; Saraswati, Pratul K.; Banerjee, Santanu [Department of Earth Sciences, Indian Institute of Technology Bombay (India); Singh, Bhagwan D.; Tripathi, Suryakant M.; Singh, Alpana [Birbal Sahni Institute of Palaeobotany, Lucknow (India); Mann, Ulrich [Forschungszentrum Juelich (Germany). Institut fuer chemie und Dynamik der Geosphaere

    2011-01-01

    Petrological, palynological and organic-geochemical investigations were undertaken to determine the source vegetation, depositional conditions and hydrocarbon source potential of Eocene Matanomadh lignites from Kutch Basin, western India. The maceral study reveals that studied lignites are rich in huminite (av. 63%) with sub-ordinate amount of liptinite (av. 19%) and low inertinite (av. 3%), along with low to moderately high associated mineral matters (av. 15%). The overall petrographic composition points to a lagoonal condition for the formation of these lignites. The mean huminite reflectance values (R{sub r}: 0.28-0.34%, av. 0.31%) as well as low Rock-Eval T{sub max} (av. 417 C) values for the seams, suggest brown coal or lignitic stage/rank for the studied lignites. The palynological assemblages, dominated by tropical angiospermic pollen, suggest prevalence of warm humid tropical climate during the deposition of these lignites. The total organic carbon (TOC) content of lignites ranges between 26 and 58 wt.%, whereas the TOC content of the associated carbonaceous shales is around 4 wt.%. The Hydrogen Index (HI) ranging from 23 to 452 mg HC/g TOC indicates that the lignite sequence has the potential to produce mixed oil and gaseous hydrocarbons on maturation. The major pyrolysis products of lignites, derived from Curie point pyrolysis-GC-MS, are straight chain aliphatics, phenols and cadalene-based C{sub 15} bicyclic sesquiterpenoids. The exclusive occurrence of C{sub 15} bicyclic sesquiterpenoids suggests that these compounds are derived from dammar resin of angiosperm plants, belonging to family Dipterocarpaceae. (author)

  16. A novel zeolite process for clean end use of hydrocarbon products

    Energy Technology Data Exchange (ETDEWEB)

    Keskinen, K M [Neste Oy, Porvoo (Finland). Technology Centre

    1997-12-31

    In recent years zeolites such as ZSM-5 have attracted considerable interest for the catalysis of a wide range of hydrocarbon transformations. A novel process developed by Neste converts light olefins to higher molecular weight hydrocarbon products. A wide range of high quality diesel, solvents and lube oils can be produced by the new NESKO process. Hydrotreated products have excellent properties; negligible sulphur or nitrogen compounds, very low aromatic content and pour point lower than -50 deg C. Proprietary technology is used in this olefin oligomerization process. (author) (7 refs.)

  17. A novel zeolite process for clean end use of hydrocarbon products

    Energy Technology Data Exchange (ETDEWEB)

    Keskinen, K.M. [Neste Oy, Porvoo (Finland). Technology Centre

    1996-12-31

    In recent years zeolites such as ZSM-5 have attracted considerable interest for the catalysis of a wide range of hydrocarbon transformations. A novel process developed by Neste converts light olefins to higher molecular weight hydrocarbon products. A wide range of high quality diesel, solvents and lube oils can be produced by the new NESKO process. Hydrotreated products have excellent properties; negligible sulphur or nitrogen compounds, very low aromatic content and pour point lower than -50 deg C. Proprietary technology is used in this olefin oligomerization process. (author) (7 refs.)

  18. Hydrocarbon composition and distribution in a coastal region under influence of oil production in northeast Brazil.

    Science.gov (United States)

    Wagener, Angela de L R; Carreira, Renato S; Hamacher, Claudia; Scofield, Arthur de L; Farias, Cassia O; Cordeiro, Lívia G M S; Luz, Letícia G; Baêta, Aída P; Kalas, Francine A

    2011-08-01

    Waters and sediments from the Potiguar Basin (NE Brazilian coast) were investigated for the presence and nature of polycyclic aromatic hydrocarbons (PAH) and aliphatic hydrocarbons. The region receives treated produced waters through a submarine outfall system serving the industrial district. The total dispersed/dissolved concentrations in the water column ranged from 10-50 ng L(-1) for ∑16PAH and 5-10 μg L(-1) for total aliphatic hydrocarbons. In the sediments, hydrocarbon concentrations were low (0.5-10 ng g(-1)for ∑16PAH and 0.01-5.0 μg g(-1) for total aliphatic hydrocarbons) and were consistent with the low organic carbon content of the local sandy sediments. These data indicate little and/or absence of anthropogenic influence on hydrocarbon distribution in water and sediment. Therefore, the measured values may be taken as background values for the region and can be used as future reference following new developments of the petroleum industry in the Potiguar Basin. Copyright © 2011 Elsevier Ltd. All rights reserved.

  19. HYDROCARBON POLLUTION IN THE NORTH-WESTERN PART OF THE CASPIAN SEA

    Directory of Open Access Journals (Sweden)

    E. V. Ostrovskaya

    2016-01-01

    Full Text Available Aim. The paper is aimed to estimate the current level of hydrocarbon pollution of the marine environment in the North-Western part of the Caspian Sea.Methods. The paper discusses the results of three-year studies conducted in 2012-2014 within the framework of Roshydromet’s Programme of monitoring of transboundary waters of the Caspian Sea. Spatial distribution of concentrations of hydrocarbons (total and polyaromatic in water and bottom sediments of the area was analysed. Concentrations of total hydrocarbons were determined by means of infrared spectrometry and PAHs – of gas chromatography with mass spectrometry.Results. The range of the total hydrocarbons in the area’s water is from slight traces to 240 µg/l, in sediments – from traces to 114 µg/g (dry weight. Total concentrations of PAHs in water varied from traces to 321 ng/l, in sediments – from traces to 699 ng/g (dry weight. For the source identification, data of satellite monitoring of the area were used. The data showed increasing input of hydrocarbons coming into the marine environment with discharges from vessels.Conclusion. The results of these studies are compared to those of previous research and show that the level of hydrocarbons in the area is typical for slightly polluted areas.

  20. Structural and electrical evolution of He ion irradiated hydrocarbon films observed by conductive atomic force microscopy

    International Nuclear Information System (INIS)

    Fan, Hongyu; Yang, Deming; Sun, Li; Yang, Qi; Niu, Jinhai; Bi, Zhenhua; Liu, Dongping

    2013-01-01

    Polymer-like hydrocarbon films are irradiated with 100 keV He ion at the fluences of 1.0 × 10 15 –1.0 × 10 17 ions/cm 2 or at the irradiation temperature ranging from 25 to 600 °C. Conductive atomic force microscopy (CAFM) has been used to evaluate the nanoscale electron conducting properties of these irradiated hydrocarbon films. Nanoscale and conducting defects have been formed in the hydrocarbon films irradiated at a relatively high ion fluence (1.0 × 10 17 ions/cm 2 ) or an elevated sample temperature. Analysis indicates that He ion irradiation results in the evolution of polymer-like hydrocarbon into a dense structure containing a large fraction of sp 2 carbon clusters. The sp 2 carbon clusters formed in irradiated hydrocarbon films can contribute to the formation of filament-like conducting channels with a relatively high local field-enhancing factor. Measurements indicate that the growth of nanoscale defects due to He ion irradiation can result in the surface swelling of irradiated hydrocarbon films at a relatively high ion fluences or elevated temperature

  1. Structural and electrical evolution of He ion irradiated hydrocarbon films observed by conductive atomic force microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Fan, Hongyu [School of Physics and Materials Engineering, Dalian Nationalities University, Dalian 116600 (China); Yang, Deming [School of Physics and Materials Engineering, Dalian Nationalities University, Dalian 116600 (China); School of Science, Changchun University of Science and Technology, Changchun, Jilin 130022 (China); Sun, Li [School of Physics and Materials Engineering, Dalian Nationalities University, Dalian 116600 (China); School of Physics, Liaoning Normal University, Dalian 116023 (China); Yang, Qi; Niu, Jinhai; Bi, Zhenhua [School of Physics and Materials Engineering, Dalian Nationalities University, Dalian 116600 (China); Liu, Dongping, E-mail: dongping.liu@dlnu.edu.cn [School of Physics and Materials Engineering, Dalian Nationalities University, Dalian 116600 (China); Fujian Key Laboratory for Plasma and Magnetic Resonance, Department of Electronic Science, Aeronautics, School of Physics and Mechanical and Electrical Engineering, Xiamen University, Xiamen, Fujian 361005 (China)

    2013-10-01

    Polymer-like hydrocarbon films are irradiated with 100 keV He ion at the fluences of 1.0 × 10{sup 15}–1.0 × 10{sup 17} ions/cm{sup 2} or at the irradiation temperature ranging from 25 to 600 °C. Conductive atomic force microscopy (CAFM) has been used to evaluate the nanoscale electron conducting properties of these irradiated hydrocarbon films. Nanoscale and conducting defects have been formed in the hydrocarbon films irradiated at a relatively high ion fluence (1.0 × 10{sup 17} ions/cm{sup 2}) or an elevated sample temperature. Analysis indicates that He ion irradiation results in the evolution of polymer-like hydrocarbon into a dense structure containing a large fraction of sp{sup 2} carbon clusters. The sp{sup 2} carbon clusters formed in irradiated hydrocarbon films can contribute to the formation of filament-like conducting channels with a relatively high local field-enhancing factor. Measurements indicate that the growth of nanoscale defects due to He ion irradiation can result in the surface swelling of irradiated hydrocarbon films at a relatively high ion fluences or elevated temperature.

  2. Hydrocarbons on Phoebe, Iapetus, and Hyperion: Quantitative Analysis

    Science.gov (United States)

    Cruikshank, Dale P.; MoreauDalleOre, Cristina; Pendleton, Yvonne J.; Clark, Roger Nelson

    2012-01-01

    We present a quantitative analysis of the hydrocarbon spectral bands measured on three of Saturn's satellites, Phoebe, Iaperus, and Hyperion. These bands, measured with the Cassini Visible-Infrared Mapping Spectrometer on close fly-by's of these satellites, are the C-H stretching modes of aromatic hydrocarbons at approximately 3.28 micrometers (approximately 3050 per centimeter), and the are four blended bands of aliphatic -CH2- and -CH3 in the range approximately 3.36-3.52 micrometers (approximately 2980- 2840 per centimeter) bably indicating the presence of polycyclic aromatic hydrocarbons (PAH), is unusually strong in comparison to the aliphatic bands, resulting in a unique signarure among Solar System bodies measured so far, and as such offers a means of comparison among the three satellites. The ratio of the C-H bands in aromatic molecules to those in aliphatic molecules in the surface materials of Phoebe, NAro:NAliph approximately 24; for Hyperion the value is approximately 12, while laperus shows an intermediate value. In view of the trend of the evolution (dehydrogenation by heat and radiation) of aliphatic complexes toward more compact molecules and eventually to aromatics, the relative abundances of aliphatic -CH2- and -CH3- is an indication of the lengths of the molecular chain structures, hence the degree of modification of the original material. We derive CH2:CH3 approximately 2.2 in the spectrum of low-albedo material on laperus; this value is the same within measurement errors to the ratio in the diffuse interstellar medium. The similarity in the spectral signatures of the three satellites, plus the apparent weak trend of aromatic/aliphatic abundance from Phoebe to Hyperion, is consistent with, and effectively confirms that the source of the hydrocarbon-bearing material is Phoebe, and that the appearance of that material on the other two satellites arises from the deposition of the inward-spiraling dust that populates the Phoebe ring.

  3. Development of an efficient bacterial consortium for the potential remediation of hydrocarbons from contaminated sites

    Directory of Open Access Journals (Sweden)

    Kaustuvmani Patowary

    2016-07-01

    Full Text Available The intrinsic biodegradability of hydrocarbons and the distribution of proficient degrading microorganisms in the environment are very crucial for the implementation of bioremediation practices. Among others, one of the most favorable methods that can enhance the effectiveness of bioremediation of hydrocarbon-contaminated environment is the application of biosurfactant producing microbes. In the present study, the biodegradation capacities of native bacterial consortia towards total petroleum hydrocarbons (TPH with special emphasis to poly aromatic hydrocarbons (PAHs were determined. The purpose of the study was to isolate TPH degrading bacterial strains from various petroleum contaminated soil of Assam, India and develop a robust bacterial consortium for bioremediation of crude oil of this native land. From a total of 23 bacterial isolates obtained from three different hydrocarbons contaminated samples 5 isolates, namely KS2, PG1, PG5, R1 and R2 were selected as efficient crude oil degraders with respect to their growth on crude oil enriched samples. Isolates KS2, PG1 and R2 are biosurfactant producers and PG5, R1 are non-producers. Fourteen different consortia were designed involving both biosurfactant producing and non-producing isolates. Consortium 10, which comprises two Bacillus strains namely, Bacillus pumilus KS2 and Bacillus cereus R2 (identified by 16s rRNA sequencing has shown the best result in the desired degradation of crude oil. The consortium showed degradation up to 84.15% of total petroleum hydrocarbon (TPH after five weeks of incubation, as revealed from gravimetric analysis. FTIR (Fourier transform infrared and GCMS (Gas chromatography-mass spectrometer analyses were correlated with gravimetric data which reveals that the consortium has removed a wide range of petroleum hydrocarbons in comparison with abiotic control including different aliphatic and aromatic hydrocarbons.

  4. Distributions of polycyclic aromatic hydrocarbons and alkylated polycyclic aromatic hydrocarbons in Osaka Bay, Japan.

    Science.gov (United States)

    Miki, Shizuho; Uno, Seiichi; Ito, Kazuki; Koyama, Jiro; Tanaka, Hiroyuki

    2014-08-30

    Contaminations in sediments by polycyclic aromatic hydrocarbons (PAHs) and alkylated PAHs were investigated at 44 sites in Osaka Bay, Japan. Concentrations of total PAHs and alkylated PAHs were in the range 6.40-7800 ng/g dry weights and 13.7-1700 ng/g dry weights, respectively. The PAH concentrations tended to be higher along the shoreline in the vicinities of big ports, industrialized areas, and densely populated regions such as the cities of Osaka and Kobe. The major sources appeared to be pyrogenic or both pyrogenic and petrogenic at most of the sites. PAH concentrations were remarkably high at a site near Kobe, where the concentrations of dibenzo(a,h)anthracene and benzo(g,h,i)perylene exceeded the effects-range-medium concentration and eight PAHs were above the corresponding effects-range-low concentrations. Those PAHs may have been derived from the great fire associated with the large earthquake in 1995. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Game Maturity Model for Health Care.

    Science.gov (United States)

    de Boer, Jan C; Adriani, Paul; van Houwelingen, Jan Willem; Geerts, A

    2016-04-01

    This article introduces the Game Maturity Model for the healthcare industry as an extension to the general Game Maturity Model and describes the usage by two case studies of applied health games. The Game Maturity Model for healthcare provides a practical and value-adding method to assess existing games and to determine strategic considerations for application of applied health games. Our forecast is that within 5 years the use and development of applied games will have a role in our daily lives and the way we organize health care that will be similar to the role social media has today.

  6. Service Quality and Process Maturity Assessment

    Directory of Open Access Journals (Sweden)

    Serek Radomir

    2013-12-01

    Full Text Available This article deals with service quality and the methods for its measurement and improvements to reach the so called service excellence. Besides older methods such as SERVQUAL and SERPERF, there are also shortly described capability maturity models based on which the own methodology is developed and used for process maturity assessment in organizations providing technical services. This method is equally described and accompanied by examples on pictures. The verification of method functionality is explored on finding a correlation between service employee satisfaction and average process maturity in a service organization. The results seem to be quite promising and open an arena for further studies.

  7. Radiolysis of hydrocarbons in liquid phase (Modern state of problem)

    International Nuclear Information System (INIS)

    Saraeva, V.V.

    1986-01-01

    Problems of ionizing radiation effect on hydrocarbons and hydrocarbon systems in a liquid phase are considered. Modern representations on the mechanism of hydrocarbon radiolysis are presented. Electron moderation and ion-electron pair formation, behaviour of charged particles, excited states, radical formation and their reactions are discussed. Behaviour of certain hydrocarbon classes: alkanes, cyclic hydrocarbons, olefines, aromatic hydrocarbons as well as different hydrocarbon mixtures is considered in detail. Radiation-chemical changes in organic coolants and ways of increasing radiation resistance are considered. Polyphenyl compounds are noted to be most perspective here

  8. Thermal-maturity limit for primary thermogenic-gas generation from humic coals as determined by hydrous pyrolysis

    Science.gov (United States)

    Lewan, Michael; Kotarba, M.J.

    2014-01-01

    Hydrous-pyrolysis experiments at 360°C (680°F) for 72 h were conducted on 53 humic coals representing ranks from lignite through anthracite to determine the upper maturity limit for hydrocarbon-gas generation from their kerogen and associated bitumen (i.e., primary gas generation). These experimental conditions are below those needed for oil cracking to ensure that generated gas was not derived from the decomposition of expelled oil generated from some of the coals (i.e., secondary gas generation). Experimental results showed that generation of hydrocarbon gas ends before a vitrinite reflectance of 2.0%. This reflectance is equivalent to Rock-Eval maximum-yield temperature and hydrogen indices (HIs) of 555°C (1031°F) and 35 mg/g total organic carbon (TOC), respectively. At these maturity levels, essentially no soluble bitumen is present in the coals before or after hydrous pyrolysis. The equivalent kerogen atomic H/C ratio is 0.50 at the primary gas-generation limit and indicates that no alkyl moieties are remaining to source hydrocarbon gases. The convergence of atomic H/C ratios of type-II and -I kerogen to this same value at a reflectance of indicates that the primary gas-generation limits for humic coal and type-III kerogen also apply to oil-prone kerogen. Although gas generation from source rocks does not exceed vitrinite reflectance values greater than , trapped hydrocarbon gases can remain stable at higher reflectance values. Distinguishing trapped gas from generated gas in hydrous-pyrolysis experiments is readily determined by of the hydrocarbon gases when a -depleted water is used in the experiments. Water serves as a source of hydrogen in hydrous pyrolysis and, as a result, the use of -depleted water is reflected in the generated gases but not pre-existing trapped gases.

  9. Method for the conversion of hydrocarbon charges

    Energy Technology Data Exchange (ETDEWEB)

    Whittam, T V

    1976-11-11

    The basis of the invention is the application of defined zeolites as catalysts to hydrocarbon conversion processes such as reformation, isomerization, dehydrocyclization, and cracking. By charging the zeolite carrier masses with 0.001 to 5% metal of the 8th group of the periodic system, preferably noble metals, a wide region of applications for the catalysts is achieved. A method for the isomerization of an alkyl benzene (or mixture of alkyl benzenes) in the liquid or gas phase under suitable temperature, pressure and flow-rate conditions, as well as in the presence of a cyclic hydrocarbon, is described as preferential model form of the invention; furthermore, a method for the reformation of a hydrocarbon fraction boiling in the gasoline or benzene boiling region and a method for the hydrocracking of hydrocarbon charge (e.g. naphtha, kerosine, gas oils) are given. Types of performance of the methods are explained using various examples.

  10. Using microorganisms to aid in hydrocarbon degradation

    International Nuclear Information System (INIS)

    Black, W.; Zamora, J.

    1993-01-01

    Aliphatic hydrocarbons are threatening the potable water supply and the aquatic ecosystem. Given the right microbial inhabitant(s), a large portion of these aliphatic hydrocarbons could be biodegraded before reaching the water supply. The authors' purpose is to isolate possible oil-degrading organisms. Soil samples were taken from hydrocarbon-laden soils at petroleum terminals, a petroleum refinery waste-treatment facility, a sewage-treatment plant grease collector, a site of previous bioremediation, and various other places. Some isolates known to be good degraders were obtained from culture collection services. These samples were plated on a 10w-30 multigrade motor oil solid medium to screen for aliphatic hydrocarbon degraders. The degrading organisms were isolated, identified, and tested (CO 2 evolution, BOD, and COD) to determine the most efficient degrader(s). Thirty-seven organisms were tested, and the most efficient degraders were Serratia marcescens, Escherichia coli, and Enterobacter agglomerans

  11. Volatilisation of aromatic hydrocarbons from soil

    DEFF Research Database (Denmark)

    Lindhardt, B.; Christensen, T.H.

    1996-01-01

    The non-steady-state fluxes of aromatic hydrocarbons were measured in the laboratory from the surface of soils contaminated with coal tar Four soil samples from a former gasworks site were used for the experiments. The fluxes were quantified for 11 selected compounds, 4 mono- and 7 polycyclic...... aromatic hydrocarbons, for a period of up to 8 or 16 days. The concentrations of the selected compounds in the soils were between 0.2 and 3,100 mu g/g. The study included the experimental determination of the distribution coefficient of the aromatic hydrocarbons between the sorbed phase and the water under...... saturated conditions. The determined distribution coefficients showed that the aromatic hydrocarbons were more strongly sorbed to the total organic carbon including the coal tar pitch - by a factor of 8 to 25 - than expected for natural organic matter. The fluxes were also estimated using an analytical...

  12. Recovering low-boiling hydrocarbons, etc

    Energy Technology Data Exchange (ETDEWEB)

    Pier, M

    1934-10-03

    A process is described for the recovery of low-boiling hydrocarbons of the nature of benzine through treatment of liquid carbonaceous materials with hydrogen under pressure at raised temperature, suitably in the presence of catalysts. Middle oils (practically saturated with hydrogen) or higher boiling oils at a temperature above 500/sup 0/ (with or without the addition of hydrogen) containing cyclic hydrocarbons not saturated with hydrogen are changed into low boiling hydrocarbons of the nature of benzine. The cracking takes place under strongly hydrogenating conditions (with the use of a strongly active hydrogenating catalyst or high pressure) at temperatures below 500/sup 0/. If necessary, the constituents boiling below 200/sup 0/ can be reconverted into cyclic hydrocarbons partially saturated with hydrogen. (BLM)

  13. Determination of polynuclear aromatic hydrocarbons (PAHs) in ...

    African Journals Online (AJOL)

    AJB SERVER

    2006-11-02

    Nov 2, 2006 ... Several water bodies in the Niger Delta region of Nigeria where extensive crude oil ..... hydrocarbons (PAHs) in fish from the Red Sea Coast of Yemem. ... smoked meat products and smoke flavouring food additives. J.

  14. Population dynamics and distribution of hydrocarbon utilizing ...

    African Journals Online (AJOL)

    Bacillus species was found to be present in all the soil samples analysed ... The presence of these organisms in soils contaminated with spent and unspent lubricating oil ... hydrocarbon utilizing bacteria, bioremediation, enrichment medium,

  15. Collision data involving hydro-carbon molecules

    International Nuclear Information System (INIS)

    Tawara, H.; Itikawa, Y.; Nishimura, H.; Tanaka, H.; Nakamura, Y.

    1990-07-01

    Hydro-carbon molecules are abundantly produced when graphites are used as internal wall materials of hydrogen plasmas and strongly influence properties of low temperature plasmas near the edges as well as those of high temperature plasmas at the center. In this report, following simple description of the production mechanisms of hydro-carbon molecules under the interactions between graphite and hydrogen plasma, the present status of collision data for hydro-carbon molecules by electron impact is discussed and the relevant data are summarized in a series of figures and tables. It should also be noted that, in addition to fusion plasmas, these hydrocarbon data compiled here are quite useful in other applications such as plasma chemistry and material processing. (author)

  16. Bazhen Fm matured reservoir evaluation (West Siberia, Russia)

    Science.gov (United States)

    Parnachev, S.; Skripkin, A.; Baranov, V.; Zakharov, S.

    2015-02-01

    The depletion of the traditional sources of hydrocarbons leads to the situation when the biggest players of the oil and gas production market turn to unconventional reserves. Commercial shale oil and gas production levels in the USA have largely determined world prospects for oil and gas industry development. Russia takes one of the leading place in the world in terms of shale oil resources. The main source rock of the West Siberia, the biggest oil and gas basin in Russia under development, the Bazhen Fm and its stratigraphic and lithologic analogs, is located in the territory of over 1,000,000 square kilometers. Provided it has similar key properties (organic carbon content, porosity, permeability) with the deposits of the Bakken Fm and Green River Fm, USA, it is still extremely poorly described with laboratory methods. We have performed the laboratory analysis of core samples from a well drilled in Bazhen Fm deposits with matured organic matter (Tmax>435 °C). It was demonstrated the applicability of the improved steady-state gas flow method to evaluate the permeability of nanopermeable rocks. The role of natural fracturing in forming voids was determided that allows regarding potential Bazhen Fm reservoirs as systems with dual porosity and dual permeability.

  17. Bazhen Fm matured reservoir evaluation (West Siberia, Russia)

    International Nuclear Information System (INIS)

    Parnachev, S; Skripkin, A; Baranov, V; Zakharov, S

    2015-01-01

    The depletion of the traditional sources of hydrocarbons leads to the situation when the biggest players of the oil and gas production market turn to unconventional reserves. Commercial shale oil and gas production levels in the USA have largely determined world prospects for oil and gas industry development. Russia takes one of the leading place in the world in terms of shale oil resources. The main source rock of the West Siberia, the biggest oil and gas basin in Russia under development, the Bazhen Fm and its stratigraphic and lithologic analogs, is located in the territory of over 1,000,000 square kilometers. Provided it has similar key properties (organic carbon content, porosity, permeability) with the deposits of the Bakken Fm and Green River Fm, USA, it is still extremely poorly described with laboratory methods. We have performed the laboratory analysis of core samples from a well drilled in Bazhen Fm deposits with matured organic matter (T max >435 °C). It was demonstrated the applicability of the improved steady-state gas flow method to evaluate the permeability of nanopermeable rocks. The role of natural fracturing in forming voids was determided that allows regarding potential Bazhen Fm reservoirs as systems with dual porosity and dual permeability

  18. Zeolitic catalytic conversion of alcohols to hydrocarbons

    Science.gov (United States)

    Narula, Chaitanya K.; Davison, Brian H.; Keller, Martin

    2018-04-10

    A method for converting an alcohol to a hydrocarbon, the method comprising contacting said alcohol with a metal-loaded zeolite catalyst at a temperature of at least 100.degree. C. and up to 550.degree. C., wherein said alcohol can be produced by a fermentation process, said metal is a positively-charged metal ion, and said metal-loaded zeolite catalyst is catalytically active for converting said alcohol to said hydrocarbon.

  19. Formation of hydrocarbons by bacteria and algae

    Energy Technology Data Exchange (ETDEWEB)

    Tornabene, T.G.

    1980-12-01

    A literature review has been performed summarizing studies on hydrocarbon synthesis by microorganisms. Certain algal and bacterial species produce hydrocarbons in large quantities, 70 to 80% of dry cell mass, when in a controlled environment. The nutritional requirements of these organisms are simple: CO/sub 2/ and mineral salts. The studies were initiated to determine whether or not microorganisms played a role in petroleum formation. 90 references. (DMC)

  20. Nitrocarburizing in ammonia-hydrocarbon gas mixtures

    DEFF Research Database (Denmark)

    Pedersen, Hanne; Christiansen, Thomas; Somers, Marcel A. J.

    2011-01-01

    The present work investigates the possibility of nitrocarburising in ammonia-acetylene-hydrogen and ammonia-propene-hydrogen gas mixtures, where unsaturated hydrocarbon gas is the carbon source during nitrocarburising. Consequently, nitrocarburising is carried out in a reducing atmosphere...... microscopy and X-ray diffraction analysis. It is shown that the use of unsaturated hydrocarbon gas in nitrocarburising processes is a viable alternative to traditional nitrocarburising methods....

  1. Nitrocarburising in ammonia-hydrocarbon gas mixtures

    DEFF Research Database (Denmark)

    Pedersen, Hanne; Christiansen, Thomas; Somers, Marcel A. J.

    2010-01-01

    The present work investigates the possibility of nitrocarburising in ammonia-acetylene-hydrogen and ammoniapropene- hydrogen gas mixtures, where unsaturated hydrocarbon gas is the carbon source during nitrocarburising. Consequently, nitrocarburising is carried out in a reducing atmosphere...... microscopy and X-ray diffraction analysis. It is shown that the use of unsaturated hydrocarbon gas in nitrocarburising processes is a viable alternative to traditional nitrocarburising methods....

  2. The future of oil and hydrocarbon man

    CERN Document Server

    Campbell, Colin

    1999-01-01

    Man appeared on the planet about four million years ago, and by 1850 numbered about one billion Ten came Hydrocarbon man. World population has since increased six-fold. After the oil price shocks of the 1970s, people asked "when will production peak?". It is not easy to answer this question because of the very poor database. Reserves and the many different hydrocarbon categories are poorly defined, reporting practices are ambiguous, revisions are not backdated...

  3. Zeolitic catalytic conversion of alochols to hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Narula, Chaitanya K.; Davison, Brian H.; Keller, Martin

    2017-01-03

    A method for converting an alcohol to a hydrocarbon, the method comprising contacting said alcohol with a metal-loaded zeolite catalyst at a temperature of at least 100.degree. C. and up to 550.degree. C., wherein said alcohol can be produced by a fermentation process, said metal is a positively-charged metal ion, and said metal-loaded zeolite catalyst is catalytically active for converting said alcohol to said hydrocarbon.

  4. An insight into the mechanism and evolution of shale reservoir characteristics with over-high maturity

    Directory of Open Access Journals (Sweden)

    Xinjing Li

    2016-10-01

    Full Text Available Over-high maturity is one of the most vital characteristics of marine organic-rich shale reservoirs from the Lower Paleozoic in the south part of China. The organic matter (OM in shale gas reservoirs almost went through the entire thermal evolution. During this wide span, a great amount of hydrocarbon was available and numerous pores were observed within the OM including kerogen and solid bitumen/pyrobitumen. These nanopores in solid bitumen/pyrobitumen can be identified using SEM. The imaging can be dissected and understood better based on the sequence of diagenesis and hydrocarbon charge with the shape of OM and pores. In terms of the maturity process showed by the various typical cases, the main effects of the relationship between the reservoir porosity and organic carbon abundance are interpreted as follows: the change and mechanism of reservoirs properties due to thermal evolution are explored, such as gas carbon isotope from partial to complete rollover zone, wettability alteration from water-wet to oil-wet and then water-wet pore surface again, electrical resistivity reversal from the increasing to decreasing stage, and nonlinearity fluctuation of rock elasticity anisotropy. These indicate a possible evolution pathway for shale gas reservoirs from the Lower Paleozoic in the southern China, as well as the general transformation processes between different shale reservoirs in thermal stages.

  5. Birds and polycyclic aromatic hydrocarbons

    Science.gov (United States)

    Albers, P.H.

    2006-01-01

    Polycyclic aromatic hydrocarbons (PAH) are present throughout the global environment and are produced naturally and by activities of humans. Effects of PAH on birds have been determined by studies employing egg injection, egg immersion, egg shell application, single and multiple oral doses, subcutaneous injection, and chemical analysis of field-collected eggs and tissue. The four-to six-ring aromatic compounds are the most toxic to embryos, young birds, and adult birds. For embryos, effects include death, developmental abnormalities, and a variety of cellular and biochemical responses. For adult and young birds, effects include reduced egg production and hatching, increased clutch or brood abandonment, reduced growth, increased organweights, and a variety of biochemical responses. Trophic level accumulation is unlikely. Environmental exposure to PAH in areas of high human population or habitats affected by recent petroleum spills might be sufficient to adversely affect reproduction. Evidence of long-term effects of elevated concentrations of environmental PAH on bird populations is very limited and the mechanisms of effect are unclear.

  6. PROTONATED POLYCYCLIC AROMATIC HYDROCARBONS REVISITED

    International Nuclear Information System (INIS)

    Ricca, Alessandra; Bauschlicher, Charles W. Jr; Allamandola, Louis J.

    2011-01-01

    We reconsider the contribution that singly protonated polycyclic aromatic hydrocarbons (PAHs; HPAH + s) might make to the Class A component of the 6.2 μm interstellar emission feature in light of the recent experimental measurements of protonated naphthalene and coronene. Our calculations on the small HPAH + s have a band near 6.2 μm, as found in experiment. While the larger HPAH + s still have emission near 6.2 μm, the much larger intensity of the band near 6.3 μm overwhelms the weaker band at 6.2 μm, so that the 6.2 μm band is barely visible. Since the large PAHs are more representative of those in the interstellar medium, our work suggests that large HPAH + s cannot be major contributors to the observed emission at 6.2 μm (i.e., Class A species). Saturating large PAH cations with hydrogen atoms retains the 6.2 μm Class A band position, but the rest of the spectrum is inconsistent with observed spectra.

  7. Polycyclic hydrocarbons - occurrence and determination

    International Nuclear Information System (INIS)

    Drzewicz, P.

    2007-01-01

    Polycyclic aromatic hydrocarbons (PAHs) are a special group of atmospheric contaminants included in the persistent toxic substances (PTS) and also in the volatile organic compounds (VOC) groups. PAHs are present in the atmosphere and their origin can be due to anthropogenic activities. The main source of emission of PAH is the combustion of fossil fuels. Their specific characteristics, high volatility, mutagenic and carcinogenic power, easily transportable for long distances with the wind, make them important contaminants despite of the fact that they are present at very low concentrations. The report provides a review of main analytical methods applied in the determination of PAH in air. Special attention was devoted to heterocyclic PAH which contain one or more heteroatom (sulphur, oxygen, nitrogen) in the multiple-fused ring. The presence of heterocyclic PAH requires very complex, laborious and long lasting sample separation methods before analysis. In some cases, application of different temperature programs in gas chromatography allows to determine PAH and heterocyclic PAH in gaseous samples without sample pretreatment. Gas chromatography methods for the determination of PAH and heterocyclic PAH in the gas from combustion of light heating oil has been optimized. (author) [pl

  8. Dewaxing hydrocarbon oils. [British patent

    Energy Technology Data Exchange (ETDEWEB)

    1933-06-23

    In dewaxing hydrocarbon oils such as residium stocks, overhead distillates and crude petroleum or shale oils, by admixing with a liquefied normally gaseous solvent, such as liquefied propane, and cooling to crystallize the wax, the rate of crystallization diminishes rapidly when a certain temperature in an example about 20/sup 0/F is reached. The diminution is prevented during further cooling by removing solvent by evaporation at such a rate that the proporation of solvent in the oil solvent component is maintained at about that existing at the temperature at which the alteration in the rate of crystallization takes place. The evaporation is effected by adjusting the pressure on the mixture, preferably in stages. Solvents for coloring matters and asphaltic compounds, such as carbon disulfide sulfur dioxide, methyl chloride or butyl alcohol may be added to the mixture before crystallization. Chilled solvent may be added to the chilled mixture before separation of the wax in a centrifuge, in order to increase the difference in specific gravity between the wax and the oil-solvent component.

  9. Biodegradation of petroleum hydrocarbons at low temperatures

    International Nuclear Information System (INIS)

    Whyte, L. G.; Greer, C W.

    1999-01-01

    Bioremediation of contaminated Arctic sites has been proposed as the logistically and economically most favorable solution despite the known technical difficulties. The difficulties involve the inhibition of pollutants removal by biodegradation below freezing temperatures and the relative slowness of the process to remove enough hydrocarbon pollutants during the above-freezing summer months. Despite these formidable drawbacks, biodegradation of hydrocarbon contaminants is possible even in below-zero temperatures, especially if indigenous psychrophilic and psychrotropic micro-organism are used. This paper reports results of a study involving several hydrocarbon-degrading psychrotropic bacteria and suggests bioaugmentation with specific cold-adapted organisms and/or biostimulation with commercial fertilizers for enhancing degradation of specific contaminants in soils from northern Canada. An evaluation of the biodegradation potential of hydrocarbon contaminated soils in the high Arctic suggested that the contaminated soils contained sufficient numbers of cold-adapted hydrocarbon-degrading bacteria and that the addition of fertilizer was sufficient to enhance the level of hydrocarbon degradation at low ambient summer temperatures. 9 refs., 2 tabs., 3 figs

  10. Comparative study between the hand-wrist method and cervical vertebral maturation method for evaluation skeletal maturity in cleft patients.

    Science.gov (United States)

    Manosudprasit, Montian; Wangsrimongkol, Tasanee; Pisek, Poonsak; Chantaramungkorn, Melissa

    2013-09-01

    To test the measure of agreement between use of the Skeletal Maturation Index (SMI) method of Fishman using hand-wrist radiographs and the Cervical Vertebral Maturation Index (CVMI) method for assessing skeletal maturity of the cleft patients. Hand-wrist and lateral cephalometric radiographs of 60 cleft subjects (35 females and 25 males, age range: 7-16 years) were used. Skeletal age was assessed using an adjustment to the SMI method of Fishman to compare with the CVMI method of Hassel and Farman. Agreement between skeletal age assessed by both methods and the intra- and inter-examiner reliability of both methods were tested by weighted kappa analysis. There was good agreement between the two methods with a kappa value of 0.80 (95% CI = 0.66-0.88, p-value <0.001). Reliability of intra- and inter-examiner of both methods was very good with kappa value ranging from 0.91 to 0.99. The CVMI method can be used as an alternative to the SMI method in skeletal age assessment in cleft patients with the benefit of no need of an additional radiograph and avoiding extra-radiation exposure. Comparing the two methods, the present study found better agreement from peak of adolescence onwards.

  11. 7 CFR 1710.115 - Final maturity.

    Science.gov (United States)

    2010-01-01

    ... Basic Policies § 1710.115 Final maturity. (a) RUS is authorized to make loans and loan guarantees with a... due, in part, to obsolescence. Operating loans to finance working capital required for the initial...

  12. Geospatial Information System Capability Maturity Models

    Science.gov (United States)

    2017-06-01

    To explore how State departments of transportation (DOTs) evaluate geospatial tool applications and services within their own agencies, particularly their experiences using capability maturity models (CMMs) such as the Urban and Regional Information ...

  13. Pristipomoides filamentosus Size at Maturity Study

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains information used to help determine median size at 50% maturity for the bottomfish species, Pristipomoides filamentosus in the Main Hawaiian...

  14. Mature teratoma of the posterior mediastinum

    Energy Technology Data Exchange (ETDEWEB)

    Kurosaki, Y.; Tanaka, Y.O.; Itai, Y. [Department of Radiology, Institute of Clinical Medicine, University of Tsukuba, Tsukuba-shi, Ibaraki-ken 305 (Japan)

    1998-02-01

    The vast majority of germ cell tumors in the thorax arise at or near the thymus. We report a case of a 41-year-old man with mature teratoma of the posterior mediastinum. He was asymptomatic and was incidentally found to have a posterior mediastinal mass. Computed tomography was helpful in suggesting a diagnosis of mature teratoma by demonstrating the presence of fat and calcification. The differential diagnosis included neurogenic tumors, liposarcoma, and extramedullary hematopoiesis. (orig.) With 2 figs., 18 refs.

  15. Mature teratoma of the posterior mediastinum

    International Nuclear Information System (INIS)

    Kurosaki, Y.; Tanaka, Y.O.; Itai, Y.

    1998-01-01

    The vast majority of germ cell tumors in the thorax arise at or near the thymus. We report a case of a 41-year-old man with mature teratoma of the posterior mediastinum. He was asymptomatic and was incidentally found to have a posterior mediastinal mass. Computed tomography was helpful in suggesting a diagnosis of mature teratoma by demonstrating the presence of fat and calcification. The differential diagnosis included neurogenic tumors, liposarcoma, and extramedullary hematopoiesis. (orig.)

  16. Radiation induced early maturing mutants in barley

    International Nuclear Information System (INIS)

    Kumar, R.; Chauhan, S.V.S.; Sharma, R.P.

    1978-01-01

    In M 2 generation, two early maturing plants were screened from a single spike progeny of a plant obtained from 20 kR of gamma-ray irradiation of a six-rowed barley (Hordeum vulgare L. var. Jyoti). Their true breeding nature was confirmed in M 3 generation. These mutants flower and mature 38 and 22 days earlier than those of control. (auth.)

  17. Intra-follicular interactions affecting mammalian oocyte maturation

    NARCIS (Netherlands)

    van Tol, H.T.A.|info:eu-repo/dai/nl/313871817

    2009-01-01

    Nuclear oocyte maturation is defined as reinitiation and progression of the first meiotic division and subsequently formation of the methaphase II (MII) plate. Concomitantly with nuclear maturation, cytoplasmic maturation which is essential for proper fertilization and early embryo development is

  18. Mature students' perspectives of studying radiography

    International Nuclear Information System (INIS)

    Williams, M.; Decker, S.

    2009-01-01

    The study set out to explore the experiences of all final year mature students on a diagnostic radiography course, in one United Kingdom University. The aims were to identify any difficulties they may have had and to make recommendations to improve mature students' learning experiences with the hope of lowering attrition rates in this group. A qualitative study involving one-to-one audio recorded interviews was utilised. Analysis of the transcripts of interviews suggested that the group believed that their maturity and previous experiences helped them in the clinical environment and put them in a good position, when asked, to counsel younger students. However for some of the mature students these experiential skills did not extend fully into seeking appropriate support for themselves. The mature students were found to be highly motivated but there was a conflict between balancing clinical and academic aspects of studying as well as balancing studying with home life. The group was found to be unprepared for the volume of academic work and its detrimental effect on family life as they sacrificed other aspects of their lives in order to complete the course. It is recommended that forewarning and forearming prospective mature students be considered by radiography education providers. Setting up and utilising an on-line forum providing a 24/7 peer support environment would aid in coping with academic, clinical or personal problems

  19. Color back projection for fruit maturity evaluation

    Science.gov (United States)

    Zhang, Dong; Lee, Dah-Jye; Desai, Alok

    2013-12-01

    In general, fruits and vegetables such as tomatoes and dates are harvested before they fully ripen. After harvesting, they continue to ripen and their color changes. Color is a good indicator of fruit maturity. For example, tomatoes change color from dark green to light green and then pink, light red, and dark red. Assessing tomato maturity helps maximize its shelf life. Color is used to determine the length of time the tomatoes can be transported. Medjool dates change color from green to yellow, and the orange, light red and dark red. Assessing date maturity helps determine the length of drying process to help ripen the dates. Color evaluation is an important step in the processing and inventory control of fruits and vegetables that directly affects profitability. This paper presents an efficient color back projection and image processing technique that is designed specifically for real-time maturity evaluation of fruits. This color processing method requires very simple training procedure to obtain the frequencies of colors that appear in each maturity stage. This color statistics is used to back project colors to predefined color indexes. Fruit maturity is then evaluated by analyzing the reprojected color indexes. This method has been implemented and used for commercial production.

  20. Breeding of cocksfoot cultivars with different maturity

    Directory of Open Access Journals (Sweden)

    Babić Snežana

    2017-01-01

    Full Text Available One of the most important criteria in breeding process of perennial grasses is maturity. Cultivars with different maturity play a very important role in utilization of perennial grasses, by providing the ability to create a mixture of different aspects utilization and time. The first grass species in Serbia whose breeding program involved this criterion was cocksfoot (Dactylis glomerata L.. In general cocksfoot is early to medium-early in maturity in comparison with other grasses and legumes, and that is mayor problem since in the optimum phase for cutting, cocksfoot is often earlier then other species in mixtures. As a result of this work, in the previous period, two cultivars of different maturity were released, Kruševačka 24 (K-24 and Kruševačka 25 (K-25. K-24 is medium and K-25 is late in maturity. New material is adapted to local agro-ecological conditions and productive in the same time. In breeding process of both cultivars initial material originated from autochthonous populations collected in eastern and central Serbia. Material from the wild flora is selected based on medium and late maturity which is already adapted and has good productivity. We applied the standard method of phenotypic recurrent selection with the creation of synthetic varieties by polycross.

  1. In vitro atrazine exposure affects the phenotypic and functional maturation of dendritic cells

    International Nuclear Information System (INIS)

    Pinchuk, Lesya M.; Lee, Sang-Ryul; Filipov, Nikolay M.

    2007-01-01

    Recent data suggest that some of the immunotoxic effects of the herbicide atrazine, a very widely used pesticide, may be due to perturbations in dendritic cell (DC) function. As consequences of atrazine exposure on the phenotypic and functional maturation of DC have not been studied, our objective was, using the murine DC line, JAWSII, to determine whether atrazine will interfere with DC maturation. First, we characterized the maturation of JAWSII cells in vitro by inducing them to mature in the presence of growth factors and selected maturational stimuli in vitro. Next, we exposed the DC cell line to a concentration range of atrazine and examined its effects on phenotypic and functional maturation of DC. Atrazine exposure interfered with the phenotypic and functional maturation of DC at non-cytotoxic concentrations. Among the phenotypic changes caused by atrazine exposure was a dose-dependent removal of surface MHC-I with a significant decrease being observed at 1 μM concentration. In addition, atrazine exposure decreased the expression of the costimulatory molecule CD86 and it downregulated the expression of the CD11b and CD11c accessory molecules and the myeloid developmental marker CD14. When, for comparative purposes, we exposed primary thymic DC to atrazine, MHC-I and CD11c expression was also decreased. Phenotypic changes in JAWSII DC maturation were associated with functional inhibition of maturation as, albeit at higher concentrations, receptor-mediated antigen uptake was increased by atrazine. Thus, our data suggest that atrazine directly targets DC maturation and that toxicants such as atrazine that efficiently remove MHC-I molecules from the DC surface are likely to contribute to immune evasion

  2. Radiographic assessment of skeletal maturation stages for orthodontic patients: hand-wrist bones or cervical vertebrae?

    Science.gov (United States)

    Lai, Eddie Hsiang-Hua; Liu, Jen-Pei; Chang, Jenny Zwei-Chieng; Tsai, Shih-Jaw; Yao, Chung-Chen Jane; Chen, Mu-Hsiung; Chen, Yi-Jane; Lin, Chun-Pin

    2008-04-01

    The skeletal maturation status of a growing patient can influence the selection of orthodontic treatment procedures. Either lateral cephalometric or hand-wrist radiography can be used to assess skeletal development. In this study, we examined the correlation between the maturation stages of cervical vertebrae and hand-wrist bones in Taiwanese individuals. The study group consisted of 330 male and 379 female subjects ranging in age from 8 to 18 years. A total of 709 hand-wrist and 709 lateral cephalometric radiographs were analyzed. Hand-wrist maturation stages were assessed using National Taiwan University Hospital Skeletal Maturation Index (NTUH-SMI). Cervical vertebral maturation stages were determined by the latest Cervical Vertebral Maturation Stage (CVMS) Index. Spearman's rank correlation was used to correlate the respective maturation stages assessed from the hand-wrist bones and the cervical vertebrae. The values of Spearman's rank correlation were 0.910 for males and 0.937 for females, respectively. These data confirmed a strong and significant correlation between CVMS and NTUH-SMI systems (p less than 0.001). After comparison of the mean ages of subjects in different stages of CVMS and NTU-SMI systems, we found that CVMS I corresponded to NTUH-SMI stages 1 and 2, CVMS II to NTUH-SMI stage 3, CVMS III to NTUHSMI stage 4, CVMS IV to NTUH-SMI stage 5, CVMS V to NTUH-SMI stages 6, 7 and 8, and CVMS VI to NTUH-SMI stage 9. Our results indicate that cervical vertebral maturation stages can be used to replace hand-wrist bone maturation stages for evaluation of skeletal maturity in Taiwanese individuals.

  3. Enhanced aerobic biodegradation of some toxic hydrocarbon pollutants

    International Nuclear Information System (INIS)

    Elshahawy, M.R.M.

    2007-01-01

    samples were collected from the same location in Suez Gulf during the period from June, 2004 to April 2006 then microbiologically and chemically analyzed . the TPH levels ranged from 55 to 86 ppm and exceeded the known permissible limits referring to a settled situation of chronic hydrocarbon pollution in the studied area. on the other hand the biodegrading bacterial counts cfu clearly reflected the great adaptation of endogenous bacteria to use hydrocarbons as a sole source of carbon . the ratio of biodegrading bacteria to heterotrophic ones ranged between 26 and 50% over the period of collection. the biodegradation potentials of suez gulf consortia were studied at different concentrations of phenanthrene as a sole carbon source. it was found that the degradation kinetics of phenanthrene either due to biotic or abiotic factors is affected with the initial concentration of PAHs. twenty PAHs degraders were isolated from Suez Gulf consortia after different adaptation periods on phenanthrene.ten isolates were selected to be promising due to their ability to tolerate high base oil concentrations, grow at wide range of temperatures and their short incubation period on MSO. the biodegradation kinetics of 200 ppm phenanthrene by the selected isolates was monitored by HPLC

  4. Technology selection for remediation of lead and hydrocarbon contaminated soil

    International Nuclear Information System (INIS)

    Richardson, K.E.; Sparks, G.M.

    1993-01-01

    This paper presents a methodology for selection of a technology for remediation of 70,000 tons of lead and hydrocarbon impacted soil resulting from an excavation at the Mobil Torrance Refinery. This methodology resulted from over two years of extensive research and technology evaluation. Twelve technologies and combination of technologies were evaluated, which often included bench scale testing, to determine the most cost effective and technically feasible remediation option. The results of the studies for each technology are discussed and presented in tabular form. The technologies investigated include: fixation/stabilization, soil washing, solvent washing, heap leach extraction, froth flotation, bioremediation, thermal desorption, electrokinetic extraction, asphalt incorporation, vitrification, off-site treatment, and off-site disposal. The associated costs and technical feasibility of each of the remediation options evaluated are presented. Laboratory analyses of the excavated soil indicate hydrocarbons range from non-detect to 11,000 ppm with an average of 2,600 ppm, soluble lead (CA test-not TCLP) range from 1.4 ppm to 100 ppm with an average of 29 ppm, and low levels of organic lead are present. Average grain size of the soil ranges from number-sign 200 to number-sign 120 mesh, and permeability averages 10--4 cm/sec. Significant odors, likely caused by hydrogen sulfide and thiophenes, were detected when the soil was excavated and control of odors during the remediation phase is a critical concern

  5. Toxicity of petroleum hydrocarbon distillates to soil organisms.

    Science.gov (United States)

    Cermak, Janet H; Stephenson, Gladys L; Birkholz, Detlef; Wang, Zhendi; Dixon, D George

    2010-12-01

    Canadian standards for petroleum hydrocarbons in soil are based on four distillate ranges (F1, C6-C10; F2, >C10-C16; F3, >C16-C34; and F4, >C34). Concerns have arisen that the ecological soil contact standards for F3 may be overly conservative. Oil distillates were prepared and characterized, and the toxicity of F3 and two subfractions, F3a (>C16-C23) and F3b (>C23-C34), to earthworms (Eisenia andrei), springtails (Orthonychiurus folsomi), and northern wheatgrass (Elymus lanceolatus), as well as the toxicity of F2 to earthworms, was determined. Clean soil was spiked with individual distillates and measured concentrations were determined for select tests. Results agree with previous studies with these distillates. Reported toxicities of crude and petroleum products to invertebrates were generally comparable to that of F3 and F3a. The decreasing order of toxicity was F3a > F3 > F3b with invertebrates, and F3a > F3b > F3 with plants. The toxicities of F3a and F3b were not sufficiently different to recommend regulating hydrocarbons based on these distillate ranges. The results also suggest that test durations may be insufficient for determining toxicity of higher distillate ranges, and that the selection of species and endpoints may significantly affect interpretation of toxicity test results. Copyright © 2010 SETAC.

  6. Role of intensive training in the growth and maturation of artistic gymnasts.

    Science.gov (United States)

    Malina, Robert M; Baxter-Jones, Adam D G; Armstrong, Neil; Beunen, Gaston P; Caine, Dennis; Daly, Robin M; Lewis, Richard D; Rogol, Alan D; Russell, Keith

    2013-09-01

    Short stature and later maturation of youth artistic gymnasts are often attributed to the effects of intensive training from a young age. Given limitations of available data, inadequate specification of training, failure to consider other factors affecting growth and maturation, and failure to address epidemiological criteria for causality, it has not been possible thus far to establish cause-effect relationships between training and the growth and maturation of young artistic gymnasts. In response to this ongoing debate, the Scientific Commission of the International Gymnastics Federation (FIG) convened a committee to review the current literature and address four questions: (1) Is there a negative effect of training on attained adult stature? (2) Is there a negative effect of training on growth of body segments? (3) Does training attenuate pubertal growth and maturation, specifically, the rate of growth and/or the timing and tempo of maturation? (4) Does training negatively influence the endocrine system, specifically hormones related to growth and pubertal maturation? The basic information for the review was derived from the active involvement of committee members in research on normal variation and clinical aspects of growth and maturation, and on the growth and maturation of artistic gymnasts and other youth athletes. The committee was thus thoroughly familiar with the literature on growth and maturation in general and of gymnasts and young athletes. Relevant data were more available for females than males. Youth who persisted in the sport were a highly select sample, who tended to be shorter for chronological age but who had appropriate weight-for-height. Data for secondary sex characteristics, skeletal age and age at peak height velocity indicated later maturation, but the maturity status of gymnasts overlapped the normal range of variability observed in the general population. Gymnasts as a group demonstrated a pattern of growth and maturation similar to

  7. Hydrocarbon pollution in the sediment from the Jarzouna-Bizerte coastal area of Tunisia (Mediterranean Sea).

    Science.gov (United States)

    Zrafi-Nouira, I; Khedir-Ghenim, Z; Zrafi, F; Bahri, R; Cheraeif, I; Rouabhia, M; Saidane-Mosbahi, D

    2008-06-01

    This study investigated the presence and origin of hydrocarbon pollution in industrial waste water sediments found near the Jarzouna (Bizerte, Tunisia) oil refinery. Analyses of surface sediments (layer 1) and deep sediments (layer 2) showed that Total Hydrocarbon (TH) concentrations ranged from 602 +/- 7.638 microg/g in layer-1 to 1270 +/- 2.176 microg/g in layer-2. The results suggest that the deeper the sediment, the higher the level of total hydrocarbon found. The sedimentary Non Aromatic Hydrocarbon (NAH) and Aromatic Hydrocarbon (AH) concentrations ranged from 66.22 +/- 1.516 to 211.82 +/- 10.670 microg/g for NAH, and from 13.84 +/- 0.180 to 115.60 +/- 2.479 microg/g for AH. The high variability of these concentrations was associated with the location of the sediment collection sites. Aliphatic biomarker analysis revealed petroleum contamination close to the refinery rejection site, and biogenic sources further away. Petroleum contamination may be associated with increased industrial activity in the area of Jarzouna-Bizerte in the Mediterranean Sea.

  8. Bioremediation of hydrocarbon-contaminated soils: are treatability and ecotoxicity endpoints related?

    International Nuclear Information System (INIS)

    Visser, S.

    1999-01-01

    To determine if there is a relationship between biotreatability and ecotoxicity endpoints in a wide range of hydrocarbon-contaminated soils, including medium and heavy crude oil-contaminated flare pit wastes and lubrication oil contaminated soil, research was conducted. Each test material was analyzed for pH, water repellency, electrical conductivity, available N and P, total extractable hydrocarbons, oil and grease, and toxicity to seedling emergence, root elongation in barley, lettuce and canola, earthworm survival and luminescent bacteria (Microtox), prior to, and following three months of bioremediation in the laboratory. By monitoring soil respiration, progress of the bioremediation process and determination of a treatment endpoint were assessed. The time required to attain a treatment endpoint under laboratory conditions can range from 30 days to 100 days depending on the concentration of hydrocarbons and degree of weathering. Most flare pits are biotreatable, averaging a loss of 25-30% of hydrocarbons during bioremediation. Once a treatment endpoint is achieved, residual hydrocarbons contents almost always exceeds Alberta Tier I criteria for mineral oil and grease. As a result of bioremediation treatments, hydrophobicity is often reduced from severe to low. Many flare pit materials are still moderately to extremely toxic after reaching a treatment endpoint. (Abstract only)

  9. Age at maturity of Mediterranean marine fishes

    Directory of Open Access Journals (Sweden)

    A. C. TSIKLIRAS

    2014-07-01

    Full Text Available In this review we collected data on the age at maturity (tm and maximum reported age (tmax for 235 stocks of Mediterranean marine fishes, belonging to 82 species, 37 families, 12 orders and 2 classes (Actinopterygii and Elasmobranchii. Among Actinopterygii (mean tm ± SD = 2.20 ± 1.43 y, n = 215, tm ranged from 0.3 y, for the common goby Pomatoschistus microps, to 12 y, for dusky grouper Epinephelus marginatus, while among Elasmobranchii (mean tm ± SD = 5.94 ± 2.47 y, n = 20, tm ranged between 2.7 y, for brown ray Raja miraletus, and 12 y for picked dogfish Squalus acanthias. Overall, the tmax ranged between 1 y, for transparent goby Aphia minuta, and 70 y, for wreckfish Polyprion americanus. The mean tmax of Actinopterygii (tmax ± SD = 10.14 ± 9.42 y was lower than that of Elasmobranchii (tmax ± SD = 14.05 ± 8.47 y. The tm exhibited a strong positive linear relation with tmax for both Actinopterygii (logtm = 0.58 ´ logtmax – 0.25, r2 = 0.51, P < 0.001 and Elasmobranchii (logtm = 0.67 ´ logtmax – 0.006, r2 = 0.51, P = 0.007. The mean tm/tmax did not differ significantly with sex within Actinopterygii (ANOVA: F = 0.27, P = 0.60, n = 90; females: mean ± SD = 0.276 ± 0.143; males: mean ± SD = 0.265 ± 0.138 and Elasmobranchii (ANOVA: F = 1.44, P = 0.25, n = 10; females: mean ± SD = 0.499 ± 0.166; males: mean ± SD = 0.418 ± 0.133. Finally, the dimensionless ratio tm/tmax was significantly lower (ANOVA: F = 31.04, P < 0.001 for Actinopterygii (mean ± SD = 0.270 ± 0.135, n = 180 than for Elasmobranchii, (mean ± SD = 0.458 ± 0.152, n = 20, when stocks with combined sexes were excluded from the analysis.

  10. Protein-induced changes during the maturation process of human dendritic cells: A 2-D DIGE approach

    DEFF Research Database (Denmark)

    Ferreira, Gb; Overbergh, L; Hansen, Kasper Lage

    2008-01-01

    Dendritic cells (DCs) are unique antigen presenting cells, which upon maturation change from a specialized antigen-capturing cell towards a professional antigen presenting cells. In this study, a 2-D DIGE analysis of immature and mature DCs was performed, to identify proteins changing in expression...... upon maturation. The protein expression profile of immature and mature DCs, derived from CD14+ peripheral blood monocytes was investigated using two pH ranges (pH 4-7 and 6-9) (n = 4). Ninety one differentially expressed spots (p...

  11. Assessment of cortical maturation with prenatal MRI. Part I: normal cortical maturation

    International Nuclear Information System (INIS)

    Fogliarini, Celine; Chaumoitre, Katia; Chapon, Frederique; Levrier, Olivier; Girard, Nadine; Fernandez, Carla; Figarella-Branger, Dominique

    2005-01-01

    Cortical maturation, especially gyral formation, follows a temporospatial schedule and is a good marker of fetal maturation. Although ultrasonography is still the imaging method of choice to evaluate fetal anatomy, MRI has an increasingly important role in the detection of brain abnormalities, especially of cortical development. Knowledge of MRI techniques in utero with the advantages and disadvantages of some sequences is necessary, in order to try to optimize the different magnetic resonance sequences to be able to make an early diagnosis. The different steps of cortical maturation known from histology represent the background necessary for the understanding of maturation in order to be then able to evaluate brain maturation through neuroimaging. Illustrations of the normal cortical maturation are given for each step accessible to MRI for both the cerebral hemispheres and the posterior fossa. (orig.)

  12. Assessment of cortical maturation with prenatal MRI. Part I: normal cortical maturation

    Energy Technology Data Exchange (ETDEWEB)

    Fogliarini, Celine [Faculte Timone, Centre de Resonance Magnetique Biologique et Medicale, Marseille (France); Chaumoitre, Katia [Hopital Nord, Department of Radiology, Marseille (France); Chapon, Frederique; Levrier, Olivier; Girard, Nadine [Hopital Timone, Department of Neuroradiology, Marseille Cedex 5 (France); Fernandez, Carla; Figarella-Branger, Dominique [Hopital Timone, Department of Pathology, Marseille (France)

    2005-08-01

    Cortical maturation, especially gyral formation, follows a temporospatial schedule and is a good marker of fetal maturation. Although ultrasonography is still the imaging method of choice to evaluate fetal anatomy, MRI has an increasingly important role in the detection of brain abnormalities, especially of cortical development. Knowledge of MRI techniques in utero with the advantages and disadvantages of some sequences is necessary, in order to try to optimize the different magnetic resonance sequences to be able to make an early diagnosis. The different steps of cortical maturation known from histology represent the background necessary for the understanding of maturation in order to be then able to evaluate brain maturation through neuroimaging. Illustrations of the normal cortical maturation are given for each step accessible to MRI for both the cerebral hemispheres and the posterior fossa. (orig.)

  13. Cracking and thermal maturity of Ordovician oils from Tahe Oilfield, Tarim Basin, NW China

    Directory of Open Access Journals (Sweden)

    Anlai Ma

    2017-12-01

    Full Text Available The thermal maturity of the Ordovician oils from the Tahe oilfield of Tarim Basin, NW China was assessed through various maturity parameters, such as biomarkers, aromatic parameters, and diamondoid parameters. Both Ts/(Ts+Tm and C29Ts/(C29H+C29Ts values indicate that the maturity of oils has not reached the condensates stage, which is consistent with the maturity obtained by MPI1. However, the diamondoid maturity suggests that the oil maturity ranges 1.1%–1.6% Ro, which is apparently higher than that of the maturity obtained by the biomarker and MPI1. This discrepancy in maturity may indicate that the Ordovician reservoir has multiple filling history. The 4-MD+3-MD concentration of oils disperses and increases slowly when the Ts/(Ts+Tm value is lower than 0.55. Meanwhile, the value increases rapidly when the Ts/(Ts+Tm value is higher than 0.55. It is proposed that the diamondoid baseline is about 15 μg/goil for marine oils in the Tahe oilfield based on the diamondoid concentration of marine oils from reservoirs of various age. The concentration of 4-MD+3-MD of most Ordovician oils generally ranges from 4.5 to 35 μg/goil, suggesting that the degree of oil-cracking is lower than 50% and the deep Ordovician have potential of oil exploration. The distribution of the concentration of 4-MD+3-MD is characterized by being high in the east and south, low in the west and north, proposing that the two migration pathways exit in the oilfield, which are from east to west and from south to north, respectively. The migration directions are consistent with the results obtained from the oil density and the maturity parameters such as Ts/(Ts+Tm. Thus, suggesting the concentration of 4-MD+3-MD can be used as migration index in oilfield scale.

  14. High-resolution gas chromatographic analysis of polycyclic aromatic hydrocarbons and aliphatic hydrocarbons

    International Nuclear Information System (INIS)

    Perez, M.; Gonzalez, D.

    1988-01-01

    A study of the analysis by gas chromatography of aromatic polycyclic hydrocarbons and aliphatic hydrocarbons is presented. The separation has been carried out by glass and fused silica capillary column in two different polar stationary phases OV-1 and SE-54. The limitation and the advantages of the procedure are discussed in terms of separation, sensitivity and precision. (Author) 20 refs

  15. Petroleum hydrocarbons and polycyclic aromatic hydrocarbons (PAHs) in Hong Kong marine sediments

    International Nuclear Information System (INIS)

    Zheng, G.J.; Richardson, B.J.

    1999-01-01

    A total of 20 surficial sediment samples, obtained from Hong Kong coastal waters, were analysed for petroleum hydrocarbons (PHCs) and a suite of 15 polycyclic aromatic hydrocarbons (PAHs). The results indicate that Hong Kong coastal sediments are often seriously polluted with petroleum related hydrocarbons. This is especially so in heavily urbanised or industrialized localities, such as Kowloon Bay (Victoria Harbour), Tsing Yi North and Tolo Harbour. Petroleum hydrocarbon pollutants in marine sediments are believed to be mainly derived from the transportation of oil, shipping activities, spillages, and industrial, stormwater and waste wastewater discharge. The ratio of unresolved complex mixture (UCM) to n-alkanes, carbon preference index (CPI), and n-C 16 values indicate that the main contribution to petroleum hydrocarbon contamination is via oil and its products. Pollutant sources appear to be stable and continuing when compared with previous data. (author)

  16. Exploring knowledge management maturity from funcionalist and interpretivist perspectives

    Directory of Open Access Journals (Sweden)

    José Enrique Arias-Pérez

    2015-01-01

    Full Text Available The purpose of this article is to explore the Knowledge Management Maturity Model (KMMM in big companies that are pioneers in the implementation of KM practices in Medellin, Colombia. The KMMM integrates the Funcionalist and Interpretivist perspectives on knowledge management and consists of four key areas: Organization and People, Processes, Technology, and Interpretation. Cluster analysis helped establishing the ranges of the five maturity levels: Initial, Awareness, Defined, Managed, and Optimized. The results showed that only two companies overcame the “Defined” level, and the best performance was achieved in the Technology key area. In conclusion, the companies have difficulties at going further the implementation of basic KM initiatives and achieving a higher level of maturity associated with the articulation of KM practices with business processes and a higher degree of appropriation and usage by individuals. This may occur because of the preponderance of the Functionalist approach in the business context and the low level of penetration and integration with the Interpretivist perspective of KM.

  17. Moral maturity and delinquency after prenatal alcohol exposure.

    Science.gov (United States)

    Schonfeld, Amy M; Mattson, Sarah N; Riley, Edward P

    2005-07-01

    Prenatal exposure to alcohol is associated with cognitive, behavioral and social deficits, including delinquency. Although delinquent populations and those with intellectual and behavioral deficits exhibit impaired moral judgment and reasoning, this area remains unexplored in alcohol-exposed individuals. Moral maturity and delinquency were evaluated in 27 participants with prenatal alcohol exposure (ALC group) and 29 nonexposed controls (CON group) matched on age (range: 10-18), gender, handedness, socioeconomic status and ethnicity. Moral maturity was evaluated using the Sociomoral Reflection Measure-Short Form, and delinquency was evaluated with the Conduct Disorder (CD) Questionnaire. Additional measures included social desirability and inhibition. The ALC group performed at a lower level of moral maturity than the CON group. Whereas Verbal IQ primarily predicted this difference, a deficit on the moral value judgment having to do with relationships with others was specific to prenatal alcohol exposure. Furthermore, delinquency was higher in the ALC group, and specific sociomoral values were predictive of delinquent behavior. Finally, half of the children and adolescents with a history of prenatal alcohol exposure but without fetal alcohol syndrome had probable CD. The results of this study indicate that interventions aimed at reducing delinquency in those with prenatal alcohol exposure are necessary, and targeting moral judgment for this purpose may be beneficial.

  18. Cervical vertebral maturation and dental age in coeliac patients.

    Science.gov (United States)

    Costacurta, M; Condò, R; Sicuro, L; Perugia, C; Docimo, R

    2011-07-01

    The aim of the study was to evaluate the cervical vertebral maturation and dental age, in group of patients with coelic disease (CD), in comparison with a control group of healthy subjects. At the Paediatric Dentistry Unit of PTV Hospital, "Tor Vergata" University of Rome, 120 female patients, age range 12.0-12.9 years were recruited. Among them, 60 subjects (Group 1) were affected by CD, while the control group (Group 2) consisted of 60 healthy subjects, sex and age-matched. The Group 1 was subdivided, according to the period of CD diagnosis, in Group A (early diagnosis) and Group B (late diagnosis). The skeletal age was determined by assessing the cervical vertebral maturation, while the dental age has been determined using the method codified by Demirjiyan. STATISTICS.: The analyses were performed using the SPSS software (version 16; SPSS Inc., Chicago IL, USA). In all the assessments a significant level of alpha = 0.05 was considered. There are no statistically significant differences between Group 1 and Group 2 as for chronological age (p=0.122). Instead, from the assessment of skeletal-dental age, there are statistically significant differences between Group 1 - Group 2 (pcervical vertebral maturity can be assessed with a low cost, non invasive, easy to perform exam carried out through the routine radiographic examinations such as orthopanoramic and lateral teleradiography.

  19. Safety barriers on oil and gas platforms. Means to prevent hydrocarbon releases

    Energy Technology Data Exchange (ETDEWEB)

    Sklet, Snorre

    2005-12-15

    The main objective of the PhD project has been to develop concepts and methods that can be used to define, illustrate, analyse, and improve safety barriers in the operational phase of offshore oil and gas production platforms. The main contributions of this thesis are; Clarification of the term safety barrier with respect to definitions, classification, and relevant attributes for analysis of barrier performance Development and discussion of a representative set of hydrocarbon release scenarios Development and testing of a new method, BORA-Release, for qualitative and quantitative risk analysis of hydrocarbon releases Safety barriers are defined as physical and/or non-physical means planned to prevent, control, or mitigate undesired events or accidents. The means may range from a single technical unit or human actions, to a complex socio-technical system. It is useful to distinguish between barrier functions and barrier systems. Barrier functions describe the purpose of safety barriers or what the safety barriers shall do in order to prevent, control, or mitigate undesired events or accidents. Barrier systems describe how a barrier function is realized or executed. If the barrier system is functioning, the barrier function is performed. If a barrier function is performed successfully, it should have a direct and significant effect on the occurrence and/or consequences of an undesired event or accident. It is recommended to address the following attributes to characterize the performance of safety barriers; a) functionality/effectiveness, b) reliability/ availability, c) response time, d) robustness, and e) triggering event or condition. For some types of barriers, not all the attributes are relevant or necessary in order to describe the barrier performance. The presented hydrocarbon release scenarios include initiating events, barrier functions introduced to prevent hydrocarbon releases, and barrier systems realizing the barrier functions. Both technical and human

  20. Evaluation of hydrocarbon potential, Task 8

    International Nuclear Information System (INIS)

    Cashman, P.H.; Trexler, J.H. Jr.

    1993-01-01

    Task 8 is responsible for assessing the hydrocarbon potential of the Yucca Mountain vicinity. Our main focus is source rock stratigraphy in the Nevada Test Site (NTS) area in southern Nevada. In order to reconstruct the Paleozoic stratigraphy, we are also studying the geometry and kinematics of deformation at NTS. A thorough understanding of the structure will also be essential to predicting the nature of the Late Paleozoic rocks under Yucca Mountain. Our stratigraphic studies continue to support the interpretation that rocks mapped as the open-quotes Eleana Formationclose quotes are in fact parts of two different Mississippian units. We are now provisionally limiting the name open-quotes Eleana Formationclose quotes to the rocks that make up the Eleana Range - i.e., the rocks that we have been calling open-quotes western Eleanaclose quotes. The mudstone section (which we have until now called open-quotes eastern Eleanaclose quotes) we are provisionally calling the open-quotes Chainman Shaleclose quotes, in keeping with regional lithostratigraphic nomenclature. We continue to work out the internal stratigraphies and basin histories of both units; XRD (r-ray diffraction) determinations of clay mineralogy are an addition to our understanding of the Chainman. The basin histories place important constraints on regional paleogeographic and tectonic reconstructions. This year we have hired a consulting petroleum geologist for two jobs: (1) to review drillhole data from southern Nevada on file at NBMG and make recommendations about more detailed study of any interesting drillholes; and (2) to log the UE17e core (in the Chainman) and evaluate source rock potential. The results of these studies have been incorporated into this report, and the consultant's reports

  1. Climate change opportunities in the hydrocarbon sector

    International Nuclear Information System (INIS)

    Amey, A.

    2003-01-01

    This presentation described some of the innovative policy, market and technology approaches that are needed to move to a carbon constrained future. The world's primary power consumption is currently 12 trillion watts. Most of the energy (85 per cent) comes from fossil fuels. Climate Change Central (C3) was incorporated as a not-for-profit company in 2000. It includes representatives from major industry sectors, environmental associations, and all levels of government. C3 provides leadership in encouraging action on climate change and developing climate change partnerships and alliances. It also provides strategic intelligence in identifying climate change priorities and appropriate policy frameworks. It helps increase public awareness of the issue. While C3 is focused on reducing greenhouse gases (GHG), it stands neutral in the Kyoto Protocol debate and is working to define emission reduction priorities in partnership with all stakeholders. Priorities include energy efficiency/conservation; emission off-sets development; adaptation; technology and market innovation; and, socio-economic implications. The difficulty in reducing GHGs stems from the fact that carbon emissions, energy use, and economic growth are directly related. In a buoyant, hydrocarbon-based economy, economic growth has meant an increase in energy production, energy use and increased carbon emissions, even while emission intensity decreases significantly. The United States contributes 23 per cent of the world's total carbon emissions, of which 90 per cent comes from energy production and consumption. Many states have implemented policies to control carbon emissions. A range of policy approaches are also underway in Canada to set GHG emission targets, to support the development of GHG off-set and trading systems, and to promote renewable energy source development. Efforts are also underway to develop clean coal or zero emission coal technology, to promote distributed power generation, biofuels, and

  2. Environmental Remediation: Removal of polycyclic aromatic hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Nkansah, Marian Asantewah

    2012-11-15

    Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous persistent semi-volatile organic compounds. They are contaminants that are resistant to degradation and can remain in the environment for long periods due to their high degree of conjugation, and aromaticity. PAHs are present in industrial effluents as products of incomplete combustion processes of organic compounds. Petroleum, coal and shale oil contain extremely complex mixtures of these PAHs, and their transport and refining process can also result in the release of PAHs. It is therefore prudent that such effluents are treated before discharge into the environment. In this project, different approaches to the treatment of PAHs have been investigated. Hydrous pyrolysis has been explored as a potential technique for degrading PAHs in water using anthracene as a model compound. The experiments were performed under different conditions of temperature, substrate, redox systems and durations. The conditions include oxidising systems comprising pure water, hydrogen peroxide and Nafion-SiO2 solid catalyst in water; and reducing systems of formic acid and formic acid / Nafion-SiO2 / Pd-C catalysts to assess a range of reactivities. Products observed in GCMS analysis of the extract from the water phase include anthrone, anthraquinone, xanthone and multiple hydro-anthracene derivatives (Paper I). In addition a modified version of the Nafion-SiO2 solid catalyst in water oxidising system was tested; and reducing systems of formic acid and formic acid / Nafion-SiO2 / Pd-C catalysts were adopted for the conversion of a mixture of anthracene, fluorene and fluoranthene. The rate of conversion in the mixture was high as compared to that of only anthracene (Paper II). Also the use of LECA (Lightweight expanded clay aggregates) as an adsorbent (Paper III) for PAHs (phenanthrene, fluoranthene and pyrene) removal from water has been.(Author)

  3. Small Scale Hydrocarbon Fire Test Concept

    Directory of Open Access Journals (Sweden)

    Joachim Søreng Bjørge

    2017-11-01

    Full Text Available In the oil and gas industry, hydrocarbon process equipment was previously often thermally insulated by applying insulation directly to the metal surface. Fire protective insulation was applied outside the thermal insulation. In some cases, severe corrosion attacks were observed due to ingress of humidity and condensation at cold surfaces. Introducing a 25 mm air gap to prevent wet thermal insulation and metal wall contact is expected to solve the corrosion issues. This improved insulation methodology does, however, require more space that may not be available when refurbishing older process plants. Relocating structural elements would introduce much hot work, which should be minimized in live plants. It is also costly. The aim of the present study is therefore to develop a test concept for testing fire resistance of equipment protected with only air-gap and thermal insulation, i.e., without the fire-protective insulation. The present work demonstrates a conceptual methodology for small scale fire testing of mockups resembling a section of a distillation column. The mockups were exposed to a small-scale propane flame in a test configuration where the flow rate and the flame zone were optimized to give heat flux levels in the range 250–350 kW/m2. Results are presented for a mockup resembling a 16 mm thick distillation column steel wall. It is demonstrated that the modern distance insulation in combination with the heat capacity of the column wall indicates 30+ minutes fire resistance. The results show that this methodology has great potentials for low cost fire testing of other configurations, and it may serve as a set-up for product development.

  4. Use of NAA to determine nutritive elements in immature and mature soybeans

    International Nuclear Information System (INIS)

    Iskander, F.Y.

    1986-01-01

    During the maturation of soybeans, several changes in the chemical composition take place. However, data available relating mineral and vitamin content to maturation stage are limited and show a wide range of values. There are several factors that affect the mineral content of soybeans. These factors include, but are not limited to, soil composition, application of fertilizers, environmental conditions, and genetic factors. For the samples examined in this study all the aforementioned factors, except genetic, were kept unchanged. Neutron activation analysis (NAA) was employed to measure calcium, iron, potassium, magnesium, manganese, and zinc in three soybean varieties at three maturation stages. Samples from three soybean varieties were investigated. The three maturation stages were defined as immature, green mature, and dry mature. The concentration of calcium, iron, potassium, magnesium, manganese, and zinc in the three soybean varieties at different maturation stages are shown. The concentration of some nutritive elements (for example, calcium, iron, manganese, and zinc) in soybeans are much higher than in other grain cereals such as wheat and corn. However, it is questionable whether too much nutritional importance be given to these elements in soybeans since phytate content in soybeans is much higher than that of wheat or corn, and it has been postulated that low bioavailability of the aforementioned elements are related to phytate content

  5. Dissolved petroleum hydrocarbon concentrations in some regions of the northern Indian Ocean

    Digital Repository Service at National Institute of Oceanography (India)

    SenGupta, R.; Qasim, S.Z.; Fondekar, S.P.; Topgi, R.S.

    Dissolved petroleum hydrocarbons were measured in some parts of the Northern Indian Ocean using UV bsorbance technique with a clean up step. The concentration of oil ranged from 0.6 to 26.5 mu gl. Higher values were recorded along the oil tanker...

  6. Moss as bio-indicators of human exposure to polycyclic aromatic hydrocarbons in Portland, OR

    Science.gov (United States)

    Geoffrey H. Donovan; Sarah E. Jovan; Demetrios Gatziolis; Vicente J. Monleon

    2015-01-01

    Polycyclic aromatic hydrocarbons (PAHs) are a class of air pollutants linked to a wide range of adverse health outcomes, including asthma, cancers, cardiovascular disease, and fetal growth impairment. PAHs are emitted by combustion of organic matter (e.g. fossil fuels, plant biomass) and can accumulate in plant and animal tissues over time. Compared to criteria...

  7. Worldwide overview of hydrocarbons and perspectives

    International Nuclear Information System (INIS)

    Tonnac, Alain de; Perves, Jean-Pierre

    2013-12-01

    This publication presents and comments data regarding the share of hydrocarbons in the world energy consumption, hydrocarbon trade flows, the new situation created by the emergence of shale hydrocarbons and the consequences for the world economy, and possible risks. The authors first comment the evolution of energy consumption and outline that the objectives of CO 2 and greenhouse gas emission will not be reached (these emissions increased in 2012 and in 2013). They indicate the emission situation in the USA and Japan, and notice that the objectives defined by the IEA are quite different from those defined by the EU. They analyse the evolutions by distinguishing different periods: 2005-2008 as a reference period, 2008-2012 as a period of change, and the current period as a period of flow inversion. Then, the authors propose two different scenarios of evolution of economic and energy policies. The evolution of hydrocarbon demand is commented, and the levels of reserves (oil, conventional gas, coal, nuclear fuels) are discussed. The market evolution is also discussed, not only from an economic point of view, but also in relationship with geopolitics. The authors notably outline that the energy price is different from one country to the other, discuss the issue of hydrocarbon refining, the role of CO 2 tax

  8. Impact of dia- and catagenesis on sulphur and oxygen sequestration of biomarkers as revealed by artificial maturation of an immature sedimentary rock

    Science.gov (United States)

    Koopmans, M.P.; De Leeuw, J. W.; Lewan, M.D.; Sinninghe, Damste J.S.

    1996-01-01

    Hydrous pyrolysis of an immature (R(a)??? 0.25%) sulphur-rich marl from the Gessoso-solfifera Formation (Messinian) in the Vena del Gesso Basin was carried out at 160C ??? T ???330 C for 72 h, to study the effect of progressive diagenesis and early catagenesis on the abundance and distribution of sulphur-containing and sulphur- and oxygen-linked carbon skeletons in low-molecular-weight and highmolecular-weight fractions (e.g. kerogen). To this end, compounds in the saturated hydrocarbon fraction, monoaromatic hydrocarbon fraction, polyaromatic hydrocarbon fraction, alkylsulphide fraction and ketone fraction were quantified, as well as compounds released after desulphurisation of the polar fraction and HI/LiAIH4 treatment of the desulphurised polar fraction. Sulphur-bound phytane and (20R)-5??,14??,17??(H) and (20R)-5??,14??,17??(H) C27 C29 steranes in the polar fraction become less abundant with increasing maturation temperature, whereas the amount of their corresponding hydrocarbons increases in the saturated hydrocarbon fraction. Carbon skeletons that are bound in the kerogen by multiple bonds (e.g. C38 n-alkane and isorenieratane) are first released into the polar fraction, and then as free hydrocarbons. These changes occur at relatively low levels of thermal maturity (R(a) <0.6%), as evidenced by the 'immature' values of biomarker maturity parameters such as the ????/(????+ ???? + ????) C35 hopane ratio and the 22S/(22S + 22R)-17??,21??(H) C35 hopane ratio. Sulphur- and oxygen-bound moieties, present in the polar fraction, are not stable with increasing thermal maturation. However, alkylthiophenes, ketones. 1,2-di-n-alkylbenzenes and free n-alkanes seem to be stable thermal degradation products of these sulphur- and oxygen-bound moieties. Thus, apart from free n-alkanes, which are abundantly present in more mature sedimentary rocks and crude oils, alkylthiophenes, 1,2-di-n-alkylbenzenes and ketones can also be expected to occur. The positions of the thiophene

  9. Development of an Efficient Bacterial Consortium for the Potential Remediation of Hydrocarbons from Contaminated Sites.

    Science.gov (United States)

    Patowary, Kaustuvmani; Patowary, Rupshikha; Kalita, Mohan C; Deka, Suresh

    2016-01-01

    The intrinsic biodegradability of hydrocarbons and the distribution of proficient degrading microorganisms in the environment are very crucial for the implementation of bioremediation practices. Among others, one of the most favorable methods that can enhance the effectiveness of bioremediation of hydrocarbon-contaminated environment is the application of biosurfactant producing microbes. In the present study, the biodegradation capacities of native bacterial consortia toward total petroleum hydrocarbons (TPH) with special emphasis to poly aromatic hydrocarbons were determined. The purpose of the study was to isolate TPH degrading bacterial strains from various petroleum contaminated soil of Assam, India and develop a robust bacterial consortium for bioremediation of crude oil of this native land. From a total of 23 bacterial isolates obtained from three different hydrocarbons contaminated samples five isolates, namely KS2, PG1, PG5, R1, and R2 were selected as efficient crude oil degraders with respect to their growth on crude oil enriched samples. Isolates KS2, PG1, and R2 are biosurfactant producers and PG5, R1 are non-producers. Fourteen different consortia were designed involving both biosurfactant producing and non-producing isolates. Consortium 10, which comprises two Bacillus strains namely, Bacillus pumilus KS2 and B. cereus R2 (identified by 16s rRNA sequencing) has shown the best result in the desired degradation of crude oil. The consortium showed degradation up to 84.15% of TPH after 5 weeks of incubation, as revealed from gravimetric analysis. FTIR (Fourier transform infrared) and GCMS (Gas chromatography-mass spectrometer) analyses were correlated with gravimetric data which reveals that the consortium has removed a wide range of petroleum hydrocarbons in comparison with abiotic control including different aliphatic and aromatic hydrocarbons.

  10. Maturity Model for Advancing Smart Grid Interoperability

    Energy Technology Data Exchange (ETDEWEB)

    Knight, Mark; Widergren, Steven E.; Mater, J.; Montgomery, Austin

    2013-10-28

    Abstract—Interoperability is about the properties of devices and systems to connect and work properly. Advancing interoperability eases integration and maintenance of the resulting interconnection. This leads to faster integration, lower labor and component costs, predictability of projects and the resulting performance, and evolutionary paths for upgrade. When specifications are shared and standardized, competition and novel solutions can bring new value streams to the community of stakeholders involved. Advancing interoperability involves reaching agreement for how things join at their interfaces. The quality of the agreements and the alignment of parties involved in the agreement present challenges that are best met with process improvement techniques. The GridWise® Architecture Council (GWAC) sponsored by the United States Department of Energy is supporting an effort to use concepts from capability maturity models used in the software industry to advance interoperability of smart grid technology. An interoperability maturity model has been drafted and experience is being gained through trials on various types of projects and community efforts. This paper describes the value and objectives of maturity models, the nature of the interoperability maturity model and how it compares with other maturity models, and experiences gained with its use.

  11. Dynamics of hydrocarbon vents: Focus on primary porosity

    Science.gov (United States)

    Johansen, C.; Shedd, W.; Abichou, T.; Pineda-Garcia, O.; Silva, M.; MacDonald, I. R.

    2012-12-01

    This study investigated the dynamics of hydrocarbon release by monitoring activity of a single vent at a 1215m deep site in the Gulf of Mexico (GC600). An autonomous camera, deployed by the submersible ALVIN, was programmed to capture a close-up image every 4 seconds for approximately 3.5 hours. The images provided the ability to study the gas hydrate outcrop site (that measured 5.2x16.3cm3) in an undisturbed state. The outcrop included an array of 38 tube-like vents through which dark brown oil bubbles are released at a rate ranging from 8 bubbles per minute to 0 bubbles per minute. The average release of bubbles from all the separate vents was 59.5 bubbles per minute, equating the total volume released to 106.38cm per minute. The rate of bubble release decreased toward the end of the observation interval, which coincided approximately with the tidal minimum. Ice worms (Hesiocaeca methanicola, Desbruyères & Toulmond, 1998) were abundant at the vent site. The image sequence showed the ice-worms actively moving in and out of burrows in the mound. It has been speculated that Hesiocaeca methanicola contribute to gas hydrate decomposition by creating burrows and depressions in the gas hydrate matrix (Fisher et al, 2000). Ice worm burrows could generate pathways for the passage of oil and gas through the gas hydrate mound. Gas hydrates commonly occur along active and/or passive continental margins (Kennicutt et al, 1988a). The release of oil and gas at this particular hydrocarbon seep site is along a passive continental margin, and controlled primarily by active salt tectonics as opposed to the movement of continental tectonic plates (Salvador, 1987). We propose a descriptive model governing the release of gas and oil from deep sub-bottom reservoirs at depths of 3000-5000m (MacDonald, 1998), through consolidated and unconsolidated sediments, and finally through gas hydrate deposits at the sea floor. The oil and gas escape from the source rock and/or reservoir through

  12. Ecological risk assessment of a site contaminated with petroleum hydrocarbons

    International Nuclear Information System (INIS)

    Starodub, M.E.; Feniak, N.A.; Willes, R.F.; Moore, C.E.; Mucklow, L.

    1995-01-01

    The aquatic and terrestrial health risks associated with petroleum contamination on a decommissioned military base, contaminated with products ranging from Bunker C oil to aviation fuel, were assessed using a methodology whereby an analytical measurement of total petroleum hydrocarbons (TPH) could be correlated with compositional characterization and thus with toxicity. The constituents of petroleum hydrocarbon contamination represent wide ranges of physical-chemical properties, environmental fate, and toxicity. The composition of TPH can vary greatly, dependent on the sources or fuel types and the interaction of age as well as site- and chemical-specific characteristics in determining the impact of weathering processes. Therefore, a bulk sum analysis of TPH cannot be related to toxicity without characterization of its composition and association of the constituents, and therefore composition, with actual toxicity data. To address this need, the constituents of TPH were represented by surrogate chemicals, with selection based on structure-activity relationships and available toxicity data. Toxicological profiles were developed from governmental regulations and on the published literature for both the aquatic and terrestrial media. Risk characterization consisted of a comparison of water concentration limits and exposure limits, developed for each surrogate, to estimated surrogate concentrations throughout the site. The concentrations of surrogates were extrapolated from TPH composition characterization analyses, conducted at a select number of sampling locations, to bulk sum analyses of TPH at related sampling locations

  13. The aryl hydrocarbon receptor (AHR) transcription factor regulates megakaryocytic polyploidization.

    Science.gov (United States)

    Lindsey, Stephan; Papoutsakis, Eleftherios T

    2011-02-01

    We propose that the aryl hydrocarbon receptor (AHR) is a novel transcriptional regulator of megakaryopoietic polyploidization. Functional evidence was obtained that AHR impacts in vivo megakaryocytic differentiation and maturation; compared to wild-type mice, AHR-null mice had lower platelet counts, fewer numbers of newly synthesized platelets, increased bleeding times and lower-ploidy megakaryocytes (Mks). AHR mRNA increased 3·6-fold during ex vivo megakaryocytic differentiation, but reduced or remained constant during parallel isogenic granulocytic or erythroid differentiation. We interrogated the role of AHR in megakaryopoiesis using a validated Mk model of megakaryopoiesis, the human megakaryoblastic leukaemia CHRF cell line. Upon CHRF Mk differentiation, AHR mRNA and protein levels increased, AHR protein shifted from the cytoplasm to the nucleus and AHR binding to its consensus DNA binding sequence increased. Protein and mRNA levels of the AHR transcriptional target HES1 also increased. Mk differentiation of CHRF cells where AHR or HES1 was knocked-down using RNAi resulted in lower ploidy distributions and cells that were incapable of reaching ploidy classes ≥16n. AHR knockdown also resulted in increased DNA synthesis of lower ploidy cells, without impacting apoptosis. Together, these data support a role for AHR in Mk polyploidization and in vivo platelet function, and warrant further detailed investigations. © 2011 Blackwell Publishing Ltd.

  14. Hydrocarbon potential assessment of Ngimbang formation, Rihen field of Northeast Java Basin

    Science.gov (United States)

    Pandito, R. H.; Haris, A.; Zainal, R. M.; Riyanto, A.

    2017-07-01

    The assessment of Ngimbang formation at Rihen field of Northeast Java Basin has been conducted to identify the hydrocarbon potential by analyzing the response of passive seismic on the proven reservoir zone and proposing a tectonic evolution model. In the case of petroleum exploration in Northeast Java basin, the Ngimbang formation cannot be simply overemphasized. East Java Basin has been well known as one of the mature basins producing hydrocarbons in Indonesia. This basin was stratigraphically composed of several formations from the old to the young i.e., the basement, Ngimbang, Kujung, Tuban, Ngerayong, Wonocolo, Kawengan and Lidah formation. All of these formations have proven to become hydrocarbon producer. The Ngrayong formation, which is geologically dominated by channels, has become a production formation. The Kujung formation that has been known with the reef build up has produced more than 102 million barrel of oil. The Ngimbang formation so far has not been comprehensively assessed in term its role as a source rock and a reservoir. In 2013, one exploratory well has been drilled at Ngimbang formation and shown a gas discovery, which is indicated on Drill Stem Test (DST) reading for more than 22 MMSCFD of gas. This discovery opens new prospect in exploring the Ngimbang formation.

  15. Maturity acceleration of Italian dried sausage by Staphylococcus carnosus - Relationship between maturity and flavor compounds

    DEFF Research Database (Denmark)

    Stahnke, Louise Heller; Holck, A.; Jensen, Anni

    2002-01-01

    . Sausages with S. carnosus 833 matured more than 2 wk faster than control sausages. Maturity correlated significantly with higher amounts of branched-chain aldehydes and alcohols and both branched- and straight-chain methyl ketones-compounds arising from the breakdown of the amino acids leucine, isoleucine...

  16. IT Governance Maturity: Developing a Maturity Model Using the Delphi Method

    NARCIS (Netherlands)

    Smits, Daniël; van Hillegersberg, Jos

    2015-01-01

    To advance in maturity, organizations should pay attention to both the hard and soft sides of IT governance (ITG). The hard side is related to processes and structure, the soft side to social aspects like behavior and organizational culture. This paper describes a study to develop an ITG maturity

  17. Condensation Mechanism of Hydrocarbon Field Formation.

    Science.gov (United States)

    Batalin, Oleg; Vafina, Nailya

    2017-08-31

    Petroleum geology explains how hydrocarbon fluids are generated, but there is a lack of understanding regarding how oil is expelled from source rocks and migrates to a reservoir. To clarify the process, the multi-layer Urengoy field in Western Siberia was investigated. Based on this example, we have identified an alternative mechanism of hydrocarbon field formation, in which oil and gas accumulations result from the phase separation of an upward hydrocarbon flow. There is evidence that the flow is generated by the gases released by secondary kerogen destruction. This study demonstrates that oil components are carried by the gas flow and that when the flow reaches a low-pressure zone, it condenses into a liquid with real oil properties. The transportation of oil components in the gas flow provides a natural explanation for the unresolved issues of petroleum geology concerning the migration process. The condensation mechanism can be considered as the main process of oil field formation.

  18. EVALUATION OF PETROLEUM HYDROCARBONS ELUTION FROM SOIL

    Directory of Open Access Journals (Sweden)

    Janina Piekutin

    2015-06-01

    Full Text Available The paper presents studies on oil removal from soil by means of water elution with a help of shaking out the contaminants from the soil. The tests were performed on simulated soil samples contaminated with a mixture of petroleum hydrocarbons. The study consisted in recording the time influence and the number of elution cycles to remove contaminants from the soil. The samples were then subject to the determination of petroleum hydrocarbons, aliphatic hydrocarbons, and BTEX compounds (benzene, toluene, ethylbenzene, xylene. Due to adding various concentrations of petroleum into particular soil samples and applying different shaking times, it was possible to find out the impact of petroleum content and sample shaking duration on the course and possibility of petroleum substances removal by means of elution process.

  19. Direct electroreduction of CO2 into hydrocarbon

    International Nuclear Information System (INIS)

    Winea, Gauthier; Ledoux, Marc-Jacques; Pham-Huu, Cuong; Gangeri, Miriam; Perathoner, Siglinda; Centi, Gabriele

    2006-01-01

    A lot of methods exist to directly reduce carbon dioxide into hydrocarbons: the photoelectrochemical process is certainly the most interesting, essentially due to the similarities with photosynthesis. As the human activities produce a great quantity of CO 2 , this one can then be considered as an infinite source of carbon. The products of this reaction are identical to those obtained during a Fischer-Tropsch reaction, that is to say hydrocarbons, alcohols and carboxylic acids. These works deal with the electrochemical reduction of CO 2 in standard conditions of temperature and pressure. The photochemical part has been replaced by a current generator as electrons source and a KHCO 3 aqueous solution as protons source. The first catalytic results clearly show that it is possible to reduce CO 2 into light hydrocarbons, typically from C1 to C9. (O.M.)

  20. Microbial hydrocarbon degradation - bioremediation of oil spills

    Energy Technology Data Exchange (ETDEWEB)

    Atlas, R M [Louisville Univ., KY (United States). Dept. of Biology

    1991-01-01

    Bioremediation has become a major method employed in restoration of oil-polluted environments that makes use of natural microbial biodegradative activities. Bioremediation of petroleum pollutants overcomes the factors limiting rates of microbial hydrocarbon biodegradation. Often this involves using the enzymatic capabilities of the indigenous hydrocarbon-degrading microbial populations and modifying environmental factors, particularly concentrations of molecular oxygen, fixed forms of nitrogen and phosphate to achieve enhanced rates of hydrocarbon biodegradation. Biodegradation of oily sludges and bioremediation of oil-contaminated sites has been achieved by oxygen addition-e.g. by tilling soils in landfarming and by adding hydrogen peroxide or pumping oxygen into oiled aquifers along with addition of nitrogen- and phosphorous-containing fertilizers. The success of seeding oil spills with microbial preparations is ambiguous. Successful bioremediation of a major marine oil spill has been achieved based upon addition of nitrogen and phosphorus fertilizers. (author).

  1. Microbiology and geochemistry of hydrocarbon-rich sediments erupted from the deep geothermal Lusi site, Indonesia

    Science.gov (United States)

    Krüger, Martin; Straten, Nontje; Mazzini, Adriano; Scheeder, Georg; Blumenberg, Martin

    2016-04-01

    The Lusi eruption represents one of the largest ongoing sedimentary hosted geothermal systems, which started in 2006 following an earthquake on Java Island. Since then it has been producing hot and hydrocarbon rich mud from a central crater with peaks reaching 180.000 m3 per day. Numerous investigations focused on the study of offshore microbial colonies that commonly thrive at offshore methane and oil seeps and mud volcanoes, however very little has been done for onshore seeping structures. Lusi represents a unique opportunity to complete a comprehensive study of onshore microbial communities fed by the seepage of CH4 as well as of heavier liquid hydrocarbons originating from one or more km below the surface. While the source of the methane at Lusi is clear (Mazzini et al., 2012), the origin of the seeping oil, either form the deep mature Eocene Ngimbang (type II kerogen) or from the less mature Pleistocene Upper Kalibeng Fm. (type III kerogen), is still discussed. In the framework of the Lusi Lab project (ERC grant n° 308126) we analysed an oil film and found that carbon preference indices among n-alkanes, sterane and hopane isomers (C29-steranes: 20S/(20S+20R) and α,β-C32 Hopanes (S/(S+R), respectively) are indicative of a low thermal maturity of the oil source rock (~0.5 to 0.6 % vitrinite reflectance equivalents = early oil window maturity). Furthermore, sterane distributions, the pristane to phytane ratio and a relatively high oleanane index, which is an indication of an angiosperm input, demonstrate a strong terrestrial component in the organic matter. Together, hydrocarbons suggest that the source of the oil film is predominantly terrestrial organic matter. Both, source and maturity estimates from biomarkers, are in favor of a type III organic matter source and are therefore suggestive of a mostly Pleistocene Upper Kalibeng Fm. origin. We also conducted a sampling campaign at the Lusi site collecting samples of fresh mud close to the erupting crater

  2. [Maturation diagnosis in full term hypotrophic fetuses].

    Science.gov (United States)

    Scharnke, H D; Gartzke, J; Fleischer, G; Isbruch, E

    1977-01-01

    Foam-Test by Clements is a valuable method for determining the foetus maturity of lungs. We introduce this test along with other parameters for the maturity-diagnosis since one year. In 15% result, the Foam-Test was not applicable because of blood, or meconic amniotic fluid, other wise wrong negative and in 0% wrong positive results. By unmatured child, there was doubtable results with Foam-Test. Since it is important to determine the early delivery of unmatured children, particularly the case of foetus maturity of lungs must be exact, we therefore decided to use the Lecithin/Sphingomyelinquotients in some cases. The results of Lecithin/Sphingomyelinquotient in unmatured children are almost with the approximated date under two. From this, one must deduce from these children, that the intrauterine unmatured lungs lately took place.

  3. Capability maturity models for offshore organisational management.

    Science.gov (United States)

    Strutt, J E; Sharp, J V; Terry, E; Miles, R

    2006-12-01

    The goal setting regime imposed by the UK safety regulator has important implications for an organisation's ability to manage health and safety related risks. Existing approaches to safety assurance based on risk analysis and formal safety assessments are increasingly considered unlikely to create the step change improvement in safety to which the offshore industry aspires and alternative approaches are being considered. One approach, which addresses the important issue of organisational behaviour and which can be applied at a very early stage of design, is the capability maturity model (CMM). The paper describes the development of a design safety capability maturity model, outlining the key processes considered necessary to safety achievement, definition of maturity levels and scoring methods. The paper discusses how CMM is related to regulatory mechanisms and risk based decision making together with the potential of CMM to environmental risk management.

  4. Mature Oocyte Cryopreservation for Fertility Preservation.

    Science.gov (United States)

    Liang, Tina; Motan, Tarek

    2016-01-01

    In recent decades, advances in cancer treatment have led to a dramatic improvement in long term survival. This has led to an increasing focus on quality of life after surviving cancer treatment, with fertility being an important aspect. Given the known reproductive risks of cancer therapies, there has been a growing interest in the field of fertility preservation (also referred to as oncofertility). Mature oocyte cryopreservation is no longer considered experimental and has become a realistic option for reproductive aged women prior to undergoing cancer treatment. Additionally, as cryopreservation techniques improve, mature oocyte cryopreservation is increasing being marketed to healthy women without cancer wishing to delay child bearing, also termed "social egg freezing". This chapter provides a review of the current technology, use, and outcomes of mature oocyte cryopreservation. It also outlines the ethical debate surrounding social egg freezing and directions for future research in female fertility preservation.

  5. Genetic transformation of mature citrus plants.

    Science.gov (United States)

    Cervera, Magdalena; Juárez, José; Navarro, Luis; Peña, Leandro

    2005-01-01

    Most woody fruit species have long juvenile periods that drastically prolong the time required to analyze mature traits. Evaluation of characteristics related to fruits is a requisite to release any new variety into the market. Because of a decline in regenerative and transformation potential, genetic transformation procedures usually employ juvenile material as the source of plant tissue, therefore resulting in the production of juvenile plants. Direct transformation of mature material could ensure the production of adult transgenic plants, bypassing in this way the juvenile phase. Invigoration of the source adult material, establishment of adequate transformation and regeneration conditions, and acceleration of plant development through grafting allowed us to produce transgenic mature sweet orange trees flowering and bearing fruits in a short time period.

  6. Bioremediation of Petroleum Hydrocarbon Contaminated Sites

    Energy Technology Data Exchange (ETDEWEB)

    Fallgren, Paul

    2009-03-30

    Bioremediation has been widely applied in the restoration of petroleum hydrocarbon-contaminated. Parameters that may affect the rate and efficiency of biodegradation include temperature, moisture, salinity, nutrient availability, microbial species, and type and concentration of contaminants. Other factors can also affect the success of the bioremediation treatment of contaminants, such as climatic conditions, soil type, soil permeability, contaminant distribution and concentration, and drainage. Western Research Institute in conjunction with TechLink Environmental, Inc. and the U.S. Department of Energy conducted laboratory studies to evaluate major parameters that contribute to the bioremediation of petroleum-contaminated drill cuttings using land farming and to develop a biotreatment cell to expedite biodegradation of hydrocarbons. Physical characteristics such as soil texture, hydraulic conductivity, and water retention were determined for the petroleum hydrocarbon contaminated soil. Soil texture was determined to be loamy sand to sand, and high hydraulic conductivity and low water retention was observed. Temperature appeared to have the greatest influence on biodegradation rates where high temperatures (>50 C) favored biodegradation. High nitrogen content in the form of ammonium enhanced biodegradation as well did the presence of water near field water holding capacity. Urea was not a good source of nitrogen and has detrimental effects for bioremediation for this site soil. Artificial sea water had little effect on biodegradation rates, but biodegradation rates decreased after increasing the concentrations of salts. Biotreatment cell (biocell) tests demonstrated hydrocarbon biodegradation can be enhanced substantially when utilizing a leachate recirculation design where a 72% reduction of hydrocarbon concentration was observed with a 72-h period at a treatment temperature of 50 C. Overall, this study demonstrates the investigation of the effects of

  7. Isotope reversals in hydrocarbon gases of natural shale systems and well head production data

    Energy Technology Data Exchange (ETDEWEB)

    Berner, U.; Schloemer, S.; Stiller, E. [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Hannover (Germany); Marquardt, D. [Rijksuniversiteit Utrecht (Netherlands)

    2013-08-01

    Relationships between gas geochemical signatures and the thermal maturity of source rocks containing aquatic organic matter are based on on pyrolysis experiments and have been successfully used in conventional hydrocarbon exploration since long. We demonstrate how these models can be applied to the evaluation of unconventional shale resources. For this purpose hydrocarbon gases have been extracted from low and high mature source rocks (type II kerogens) using laboratory desorption techniques. We determined the molecular composition of the gases as well as the carbon isotope ratios of methane to propane. In the extracted gases we observe an increase of {sup 13}C content in methane with increasing dry gas ratio (C1/{Sigma}C1-6). The carbon isotope ratios of ethane and propane initially increase with increasing dryness but start to become isotopically lighter above a dry gas ratio of 0.8. We show that oil-to-gas cracking explains the observed gas geochemical data, and that mixing between gases from different processes is a key factor to describe natural hydrocarbon systems of shales. However, data from published case studies using well head gases which show 'isotope roll-over' effects indicate that the isotopic reversal observed in well head samples deviate from those observed in natural shale systems in a fundamental way. We show that isotope reversals related to well head gases are best explained by an additional isotope fractionation effect induced through hydraulic fracturing and gas migration from the shale to the well head. Although, this induced isotope fractionation is an artifact which obscures isotopic information of natural systems to a large extend, we suggest a simple classification scheme which allows distinguishing between hot and cool spot areas using well head or mud line gas data. (orig.)

  8. Vegetative propagation of mature and juvenile northern red oak

    Science.gov (United States)

    James J. Zaczek; K. C. Steiner; C. W., Jr. Heuser

    1993-01-01

    Rooting trials were established to evaluate rooting success of cuttings from mature and juvenile, grafted and ungrafted northern red oak (NRO). Buds from 4 mature NRO ortets and juvenile seedlings were grafted onto juvenile and mature rootstock. Cuttings were collected from the grafts and from juvenile and mature shoots developed in situ and...

  9. Validation of an analytical methodology for the quantitative analysis of petroleum hydrocarbons in marine sediment samples

    Directory of Open Access Journals (Sweden)

    Eloy Yordad Companioni Damas

    2009-01-01

    Full Text Available This work describes a validation of an analytical procedure for the analysis of petroleum hydrocarbons in marine sediment samples. The proposed protocol is able to measure n-alkanes and polycyclic aromatic hydrocarbons (PAH in samples at concentrations as low as 30 ng/g, with a precision better than 15% for most of analytes. The extraction efficiency of fortified sediments varied from 65.1 to 105.6% and 59.7 to 97.8%, for n-alkanes and PAH in the ranges: C16 - C32 and fluoranthene - benzo(apyrene, respectively. The analytical protocol was applied to determine petroleum hydrocarbons in sediments collected from a marine coastal zone.

  10. Biological treatment process for removing petroleum hydrocarbons from oil field produced waters

    Energy Technology Data Exchange (ETDEWEB)

    Tellez, G.; Khandan, N.

    1995-12-31

    The feasibility of removing petroleum hydrocarbons from oil fields produced waters using biological treatment was evaluated under laboratory and field conditions. Based on previous laboratory studies, a field-scale prototype system was designed and operated over a period of four months. Two different sources of produced waters were tested in this field study under various continuous flow rates ranging from 375 1/D to 1,800 1/D. One source of produced water was an open storage pit; the other, a closed storage tank. The TDS concentrations of these sources exceeded 50,000 mg/l; total n-alkanes exceeded 100 mg/l; total petroleum hydrocarbons exceeded 125 mg/l; and total BTEX exceeded 3 mg/l. Removals of total n-alkanes, total petroleum hydrocarbons, and BTEX remained consistently high over 99%. During these tests, the energy costs averaged $0.20/bbl at 12 bbl/D.

  11. Stability of hydrocarbon systems at thermobaric conditions corresponding to depth down to 50 km

    Science.gov (United States)

    Kutcherov, V.; Kolesnikov, A.; Mukhina, E.; Serovaiskii, A.

    2017-12-01

    Most of the theoretical models show that crude oil stability is limited by the depth of 6-8 km (`oil window'). Commercial discovery of crude oil deposits on the depth more than 10 km in the different petroleum basins worldwide casts doubt on the validity of the above-mentioned theoretical calculations. Therefore, the question at which depth complex hydrocarbon systems could be stable is important not only from fundamental research point of view but has a great practical application. To answer this question a hydrocarbon mixture was investigated under thermobaric conditions corresponding to the conditions of the Earth's lower crust. Experiments were conducted by means of Raman Mössbauer spectroscopy. The results obtained show that the complex hydrocarbon systems could be stable and remain their qualitative and quantitative composition at temperature 320-450 °C and pressure 0.7-1.4 GPa. The oxidizing resistance of hydrocarbon system was tested in the modelled the Earth's crust surrounding. The hydrocarbon system stability at the presence of Fe2O3 strongly confirms that the Earth's crust oxygen fugacity does not influence on petroleum composition. The data obtained broaden our knowledge about the possible range of depths for crude oil and natural gas deposits in the Earth's crust and give us the possibility to revise the depth of petroleum deposits occurrence.

  12. Integration of direct carbon and hydrogen fuel cells for highly efficient power generation from hydrocarbon fuels

    Energy Technology Data Exchange (ETDEWEB)

    Muradov, Nazim; Choi, Pyoungho; Smith, Franklyn; Bokerman, Gary [Florida Solar Energy Center, University of Central Florida, 1679 Clearlake Road, Cocoa, FL 32922-5703 (United States)

    2010-02-15

    In view of impending depletion of hydrocarbon fuel resources and their negative environmental impact, it is imperative to significantly increase the energy conversion efficiency of hydrocarbon-based power generation systems. The combination of a hydrocarbon decomposition reactor with a direct carbon and hydrogen fuel cells (FC) as a means for a significant increase in chemical-to-electrical energy conversion efficiency is discussed in this paper. The data on development and operation of a thermocatalytic hydrocarbon decomposition reactor and its coupling with a proton exchange membrane FC are presented. The analysis of the integrated power generating system including a hydrocarbon decomposition reactor, direct carbon and hydrogen FC using natural gas and propane as fuels is conducted. It was estimated that overall chemical-to-electrical energy conversion efficiency of the integrated system varied in the range of 49.4-82.5%, depending on the type of fuel and FC used, and CO{sub 2} emission per kW{sub el}h produced is less than half of that from conventional power generation sources. (author)

  13. POLYCYCLIC AROMATIC HYDROCARBON CONTAMINATION LEVELS IN COLLECTED SAMPLES FROM VICINITY OF A HIGHWAY

    Directory of Open Access Journals (Sweden)

    S. V. Samimi ، R. Akbari Rad ، F. Ghanizadeh

    2009-01-01

    Full Text Available Tehran as the biggest city of Iran with a population of more than 10 millions has potentially high pollutant exposures of gas oil and gasoline combustion from vehicles that are commuting in the highways every day. The vehicle exhausts contain polycyclic aromatic hydrocarbons, which are produced by incomplete combustion and can be directly deposited in the environment. In the present study, the presence of polycyclic aromatic hydrocarbons contamination in the collected samples of a western highway in Tehran was investigated. The studied location was a busy highway in Tehran. High performance liquid chromatography equipped with florescence detector was used for determination of polycyclic aromatic hydrocarbons concentrations in the studied samples. Total concentration of the ten studied polycyclic aromatic hydrocarbons compounds ranged from 11107 to 24342 ng/g dry weight in the dust samples and increased from 164 to 2886 ng/g dry weight in the soil samples taken from 300 m and middle of the highway, respectively. Also the average of Σ PAHs was 1759 ng/L in the water samples of pools in parks near the highway. The obtained results indicated that polycyclic aromatic hydrocarbons contamination levels were very high in the vicinity of the highway.

  14. Observations of the release of non-methane hydrocarbons from fractured shale.

    Science.gov (United States)

    Sommariva, Roberto; Blake, Robert S; Cuss, Robert J; Cordell, Rebecca L; Harrington, Jon F; White, Iain R; Monks, Paul S

    2014-01-01

    The organic content of shale has become of commercial interest as a source of hydrocarbons, owing to the development of hydraulic fracturing ("fracking"). While the main focus is on the extraction of methane, shale also contains significant amounts of non-methane hydrocarbons (NMHCs). We describe the first real-time observations of the release of NMHCs from a fractured shale. Samples from the Bowland-Hodder formation (England) were analyzed under different conditions using mass spectrometry, with the objective of understanding the dynamic process of gas release upon fracturing of the shale. A wide range of NMHCs (alkanes, cycloalkanes, aromatics, and bicyclic hydrocarbons) are released at parts per million or parts per billion level with temperature- and humidity-dependent release rates, which can be rationalized in terms of the physicochemical characteristics of different hydrocarbon classes. Our results indicate that higher energy inputs (i.e., temperatures) significantly increase the amount of NMHCs released from shale, while humidity tends to suppress it; additionally, a large fraction of the gas is released within the first hour after the shale has been fractured. These findings suggest that other hydrocarbons of commercial interest may be extracted from shale and open the possibility to optimize the "fracking" process, improving gas yields and reducing environmental impacts.

  15. Hydrocarbon Plume Dynamics in the Worldś Most Spectacular Hydrocarbon Seeps, Santa Barbara Channel, California

    Science.gov (United States)

    Mau, S.; Reed, J.; Clark, J.; Valentine, D.

    2006-12-01

    Large quantities of natural gas are emitted from the seafloor into the coastal ocean near Coal Oil Point, Santa Barbara Channel (SBC), California. Methane, ethane, and propane were quantified in the surface water at 79 stations in a 270 km2 area in order to map the surficial hydrocarbon plume and to quantify air-sea exchange of these gases. A time series was initiated for 14 stations to identify the variability of the mapped plume, and biologically-mediated oxidation rates of methane were measured to quantify the loss of methane in surface water. The hydrocarbon plume was found to comprise ~70 km2 and extended beyond study area. The plume width narrowed from 3 km near the source to 0.7 km further from the source, and then expanded to 6.7 km at the edge of the study area. This pattern matches the cyclonic gyre which is the normal current flow in this part of the Santa Barbara Channel - pushing water to the shore near the seep field and then broadening the plume while the water turns offshore further from the source. Concentrations of gaseous hydrocarbons decrease as the plume migrates. Time series sampling shows similar plume width and hydrocarbon concentrations when normal current conditions prevail. In contrast, smaller plume width and low hydrocarbon concentrations were observed when an additional anticyclonic eddy reversed the normal current flow, and a much broader plume with higher hydrocarbon concentrations was observed during a time of diminished speed within the current gyre. These results demonstrate that surface currents control hydrocarbon plume dynamics in the SBC, though hydrocarbon flux to the atmosphere is likely less dependent on currents. Estimates of air- sea hydrocarbon flux and biological oxidation rates will also be presented.

  16. Electrochemical removal of NOx and hydrocarbons

    DEFF Research Database (Denmark)

    Friedberg, Anja Zarah

    on the electrodes during polarisation, probably because of strong adsorption of the hydrocarbon relative to NO. On LSF/CGO electrode the impregnation of ionic conducting material increased the oxidation of NO to NO2 which is an important step before nitrogen formation. The propene inhibited this reaction because....... This could only be done if the electrode was impregnated with BaO. The nitrate formation did not seem to be inhibited by the presence of the hydrocarbon. However, the oxidation of propene was inhibited by the BaO because the active sites for oxidations were partially covered by the BaO nanoparticles...

  17. Mathematics of Periodic Tables for Benzenoid Hydrocarbons.

    Science.gov (United States)

    Dias, Jerry Ray

    2007-01-01

    The upper and lower bounds for invariants of polyhex systems based on the Harary and Harborth inequalities are studied. It is shown that these invariants are uniquely correlated by the Periodic Table for Benzenoid Hydrocarbons. A modified periodic table for total resonant sextet (TRS) benzenoids based on the invariants of Ds and r(empty) is presented; Ds is the number of disconnections among the empty rings for fused TRS benzenoid hydrocarbons. This work represents a contribution toward deciphering the topological information content of benzenoid formulas.

  18. Plasma-catalytic reforming of liquid hydrocarbons

    International Nuclear Information System (INIS)

    Nedybaliuk, O.A.; Chernyak, V.Ya; Kolgan, V.V.; Iukhymenko, V.V.; Solomenko, O.V.; Fedirchyk, I.I.; Martysh, E.V.; Demchina, V.P.; Klochok, N.V.; Dragnev, S.V.

    2015-01-01

    The series of experiments studying the plasma-catalytic reforming of liquid hydrocarbons was carried out. The dynamic plasma-liquid system based on a low-power rotating gliding arc with solid electrodes was used for the investigation of liquid hydrocarbons reforming process. Conversion was done via partial oxidation. A part of oxidant flow was activated by the discharge. Synthesis-gas composition was analysed by means of mass-spectrometry and gas-chromatography. A standard boiler, which operates on natural gas and LPG, was used for the burning of synthesis-gas

  19. Motor fuels by hydrogenation of liquid hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    1938-05-07

    A process is disclosed for the production of knock-stable low-boiling motor fuels by conversion of liquid hydrocarbons which are vaporizable under the reaction conditions, which comprises passing the initial material at a temperature above 380/sup 0/C in a true vapor phase under pressure of more than 40 atmospheres together with hydrogen and gaseous hydrocarbons containing more than 1 carbon atom in the molecule in an amount by volume larger than that of the hydrogen over catalysts stable to poisoning stationarily confined in the reaction vessel.

  20. Adult maturational processes and the facilitating environment.

    Science.gov (United States)

    Acklin, M W

    1986-09-01

    The psychoanalytic theory of religion has been seriously limited in its development, largely owing to Freud's emphasis on religion's neurotic elements and an overemphasis on the infantile origins of religious development. This paper offers a conceptual framework and advances the thesis, based on contemporary psychoanalytic, developmental theory, that 1) Erikson's concept of epigenesis has applicability across the life span; 2) that beyond-the-self identity is constituent to human maturation and self-completion; 3) that successful adult maturation requires a mirroring-facilitating environment; and 4) that religious values, meanings, images, and communities play an essential role-as-elements of the facilitating environment of later life.

  1. Digital Maturity of the Firm's Business Model

    DEFF Research Database (Denmark)

    Groskovs, Sergejs; Vemula, Sreekanth

    We propose a digital maturity assessment model as an instrument for researchers and a strategic tool for managers. Existing literature lacks a conceptually clear way to measure the construct of digital maturity at the level of the firms business model. Our proposed instrument thus opens avenues...... for research into questions related to antecedents, process, and performance outcomes of the digitalization of business activities. The assessment follows the logic of first decomposing the business model into the underlying value creation activities and then evaluating the levels of automation...

  2. Posttesticular sperm maturation, infertility, and hypercholesterolemia

    Directory of Open Access Journals (Sweden)

    Marjorie Whitfield

    2015-01-01

    Full Text Available Cholesterol is a key molecule in the mammalian physiology of especial particular importance for the reproductive system as it is the common precursor for steroid hormone synthesis. Cholesterol is also a recognized modulator of sperm functions, not only at the level of gametogenesis. Cholesterol homeostasis regulation is crucial for posttesticular sperm maturation, and imbalanced cholesterol levels may particularly affect these posttesticular events. Metabolic lipid disorders (dyslipidemia affect male fertility but are most of the time studied from the angle of endocrine/testicular consequences. This review will focus on the deleterious effects of a particular dyslipidemia, i.e., hypercholesterolemia, on posttesticular maturation of mammalian spermatozoa.

  3. Anaerobic Microbial Degradation of Hydrocarbons: From Enzymatic Reactions to the Environment.

    Science.gov (United States)

    Rabus, Ralf; Boll, Matthias; Heider, Johann; Meckenstock, Rainer U; Buckel, Wolfgang; Einsle, Oliver; Ermler, Ulrich; Golding, Bernard T; Gunsalus, Robert P; Kroneck, Peter M H; Krüger, Martin; Lueders, Tillmann; Martins, Berta M; Musat, Florin; Richnow, Hans H; Schink, Bernhard; Seifert, Jana; Szaleniec, Maciej; Treude, Tina; Ullmann, G Matthias; Vogt, Carsten; von Bergen, Martin; Wilkes, Heinz

    2016-01-01

    Hydrocarbons are abundant in anoxic environments and pose biochemical challenges to their anaerobic degradation by microorganisms. Within the framework of the Priority Program 1319, investigations funded by the Deutsche Forschungsgemeinschaft on the anaerobic microbial degradation of hydrocarbons ranged from isolation and enrichment of hitherto unknown hydrocarbon-degrading anaerobic microorganisms, discovery of novel reactions, detailed studies of enzyme mechanisms and structures to process-oriented in situ studies. Selected highlights from this program are collected in this synopsis, with more detailed information provided by theme-focused reviews of the special topic issue on 'Anaerobic biodegradation of hydrocarbons' [this issue, pp. 1-244]. The interdisciplinary character of the program, involving microbiologists, biochemists, organic chemists and environmental scientists, is best exemplified by the studies on alkyl-/arylalkylsuccinate synthases. Here, research topics ranged from in-depth mechanistic studies of archetypical toluene-activating benzylsuccinate synthase, substrate-specific phylogenetic clustering of alkyl-/arylalkylsuccinate synthases (toluene plus xylenes, p-cymene, p-cresol, 2-methylnaphthalene, n-alkanes), stereochemical and co-metabolic insights into n-alkane-activating (methylalkyl)succinate synthases to the discovery of bacterial groups previously unknown to possess alkyl-/arylalkylsuccinate synthases by means of functional gene markers and in situ field studies enabled by state-of-the-art stable isotope probing and fractionation approaches. Other topics are Mo-cofactor-dependent dehydrogenases performing O2-independent hydroxylation of hydrocarbons and alkyl side chains (ethylbenzene, p-cymene, cholesterol, n-hexadecane), degradation of p-alkylated benzoates and toluenes, glycyl radical-bearing 4-hydroxyphenylacetate decarboxylase, novel types of carboxylation reactions (for acetophenone, acetone, and potentially also benzene and

  4. Geothermal regime and Jurassic source rock maturity of the Junggar basin, northwest China

    Science.gov (United States)

    Nansheng, Qiu; Zhihuan, Zhang; Ershe, Xu

    2008-01-01

    We analyze the thermal gradient distribution of the Junggar basin based on oil-test and well-logging temperature data. The basin-wide average thermal gradient in the depth interval of 0-4000 m is 22.6 °C/km, which is lower than other sedimentary basins in China. We report 21 measured terrestrial heat flow values based on detailed thermal conductivity data and systematical steady-state temperature data. These values vary from 27.0 to 54.1 mW/m 2 with a mean of 41.8 ± 7.8 mW/m 2. The Junggar basin appears to be a cool basin in terms of its thermal regime. The heat flow distribution within the basin shows the following characteristics. (1) The heat flow decreases from the Luliang Uplift to the Southern Depression; (2) relatively high heat flow values over 50 mW/m 2 are confined to the northern part of the Eastern Uplift and the adjacent parts of the Eastern Luliang Uplift and Central Depression; (3) The lowest heat flow of smaller than 35 mW/m 2 occurs in the southern parts of the basin. This low thermal regime of the Junggar basin is consistent with the geodynamic setting, the extrusion of plates around the basin, the considerably thick crust, the dense lithospheric mantle, the relatively stable continental basement of the basin, low heat generation and underground water flow of the basin. The heat flow of this basin is of great significance to oil exploration and hydrocarbon resource assessment, because it bears directly on issues of petroleum source-rock maturation. Almost all oil fields are limited to the areas of higher heat flows. The relatively low heat flow values in the Junggar basin will deepen the maturity threshold, making the deep-seated widespread Permian and Jurassic source rocks in the Junggar basin favorable for oil and gas generation. In addition, the maturity evolution of the Lower Jurassic Badaowan Group (J 1b) and Middle Jurassic Xishanyao Group (J 2x) were calculated based on the thermal data and burial depth. The maturity of the Jurassic

  5. Fractal nature of hydrocarbon deposits. 2. Spatial distribution

    International Nuclear Information System (INIS)

    Barton, C.C.; Schutter, T.A; Herring, P.R.; Thomas, W.J.; Scholz, C.H.

    1991-01-01

    Hydrocarbons are unevenly distributed within reservoirs and are found in patches whose size distribution is a fractal over a wide range of scales. The spatial distribution of the patches is also fractal and this can be used to constrain the design of drilling strategies also defined by a fractal dimension. Fractal distributions are scale independent and are characterized by a power-law scaling exponent termed the fractal dimension. The authors have performed fractal analyses on the spatial distribution of producing and showing wells combined and of dry wells in 1,600-mi 2 portions of the Denver and Powder River basins that were nearly completely drilled on quarter-mile square-grid spacings. They have limited their analyses to wells drilled to single stratigraphic intervals so that the map pattern revealed by drilling is representative of the spatial patchiness of hydrocarbons at depth. The fractal dimensions for the spatial patchiness of hydrocarbons in the two basins are 1.5 and 1.4, respectively. The fractal dimension for the pattern of all wells drilled is 1.8 for both basins, which suggests a drilling strategy with a fractal dimension significantly higher than the dimensions 1.5 and 1.4 sufficient to efficiently and economically explore these reservoirs. In fact, the fractal analysis reveals that the drilling strategy used in these basins approaches a fractal dimension of 2.0, which is equivalent to random drilling with no geologic input. Knowledge of the fractal dimension of a reservoir prior to drilling would provide a basis for selecting and a criterion for halting a drilling strategy for exploration whose fractal dimension closely matches that of the spatial fractal dimension of the reservoir, such a strategy should prove more efficient and economical than current practice

  6. Culture-dependent characterization of hydrocarbon utilizing bacteria ...

    African Journals Online (AJOL)

    EARNEST

    Hydrocarbons interact with the environment and micro- organisms determining the .... it is pertinent to study the community dynamics of hydrocarbon degrading bacteria ... Chikere CB (2013). Application of molecular microbiology techniques in.

  7. Response of microalgae from mud-flats to petroleum hydrocarbons ...

    African Journals Online (AJOL)

    SERVER

    2008-03-04

    Mar 4, 2008 ... hydrocarbons in the presence of nitrogenous fertilizer ... the hydrocarbon, there was delayed nutrient uptake. ... waters, but the use of inorganic of organic nitrogen in ... ment, fish kills as oxygen is depleted, offensive odour.

  8. Hydrocarbons in the Hauptsalz formation of the Gorleben salt dome. Content, distribution and origin

    Energy Technology Data Exchange (ETDEWEB)

    Pusch, Maximilian; Hammer, Joerg; Ostertag-Henning, Christian [Federal Institute for Geosciences and Natural Resources (BGR), Hannover (Germany)

    2015-07-01

    boundaries of halite crystals, on the surfaces and knuckles or inside of micro capillary tubes of anhydrite crystals and anhydrite clusters, in newly formed micro cracks due to drilling respectively preparational works or rarely in micro-porous parts of the Hauptsalz. In order to get additional information about the origin of hydrocarbons detected in the Gorleben Hauptsalz organic geochemical analyses of potential source rocks in the vicinity like the Stassfurt Carbonate (z2SK) have been provided. These analyses revealed that the level of maturity of hydrocarbons in the Gorleben Hauptsalz correspond to 0,8 to 1,2% vitrinite-reflection-equivalent for the oil, similar to the organic-petrographical data of Stassfurt Carbonate and Copper schist in the periphery of the Gorleben salt dome (Gerling et al. 2002; Senglaub 2001; Cramer 2005). The analyses of biomarkers (esp. triterpenoid biomarkers) detected in the hydrocarbon mixtures from the Hauptsalz point to the Stassfurt Carbonate as source rocks of most of the hydrocarbons.

  9. Maturation Pathways of Cross-Reactive HIV-1 Neutralizing Antibodies

    Directory of Open Access Journals (Sweden)

    Dimiter S. Dimitrov

    2009-11-01

    Full Text Available Several human monoclonal antibodies (hmAbs and antibody fragments, including the best characterized in terms of structure-function b12 and Fab X5, exhibit relatively potent and broad HIV-1 neutralizing activity. However, the elicitation of b12 or b12-like antibodies in vivo by vaccine immunogens based on the HIV-1 envelope glycoprotein (Env has not been successful. B12 is highly divergent from the closest corresponding germline antibody while X5 is less divergent. We have hypothesized that the relatively high degree of specific somatic hypermutations may preclude binding of the HIV-1 envelope glycoprotein (Env to closest germline antibodies, and that identifying antibodies that are intermediates in the pathways to maturation could help design novel vaccine immunogens to guide the immune system for their enhanced elicitation. In support of this hypothesis we have previously found that a germline-like b12 (monovalent and bivalent scFv as an Fc fusion protein or IgG lacks measurable binding to an Env as measured by ELISA with a sensitivity in the μM range [1]; here we present evidence confirming and expanding these findings for a panel of Envs. In contrast, a germline-like scFv X5 bound Env with high (nM affinity. To begin to explore the maturation pathways of these antibodies we identified several possible b12 intermediate antibodies and tested their neutralizing activity. These intermediate antibodies neutralized only some HIV-1 isolates and with relatively weak potency. In contrast, germline-like scFv X5 neutralized a subset of the tested HIV-1 isolates with comparable efficiencies to that of the mature X5. These results could help explain the relatively high immunogenicity of the coreceptor binding site on gp120 and the abundance of CD4-induced (CD4i antibodies in HIV-1-infected patients (X5 is a CD4i antibody as well as the maturation pathway of X5. They also can help identify antigens that can bind specifically to b12 germline and

  10. Elevated Social Anxiety among Early Maturing Girls

    Science.gov (United States)

    Blumenthal, Heidemarie; Leen-Feldner, Ellen W.; Babson, Kimberly A.; Gahr, Jessica L.; Trainor, Casey D.; Frala, Jamie L.

    2011-01-01

    Adolescence is a key period in terms of the development of anxiety psychopathology. An emerging literature suggests that early pubertal maturation is associated with enhanced vulnerability for anxiety symptomatology, although few studies have examined this association with regard to social anxiety. Accordingly, the current study was designed to…

  11. Mature cystic teratomas: Relationship between histopathological ...

    African Journals Online (AJOL)

    ... tumor size, symptoms related to MCT and laterality of the tumor did not differ among the patients according to the MCT contents. Conclusions: Our findings suggest no relationship between the clinical features and histopathological contents of MCTs. Key words: Histopathological contents, mature cystic teratoma, ovarian, ...

  12. Intraovarian markers of follicular and oocyte maturation.

    Science.gov (United States)

    Pellicer, A; Diamond, M P; DeCherney, A H; Naftolin, F

    1987-08-01

    The use of ovulation induction for multiple follicular growth in in vitro fertilization (IVF) has introduced the problem of follicular asynchrony. As a consequence of the asynchrony, the parameters most commonly used by IVF groups to assess follicular and oocyte quality within those follicles are not sufficiently sensitive or specific. Thus, each follicle must be considered separately, and specific markers of follicular and/or oocyte maturation must be sought from within the follicle. In this review we analyze previous reports of potential markers of follicular and oocyte maturation. In regards to the follicular fluid constituents, the level of estradiol in follicular fluid correlates with fertilization and pregnancy in stimulated cycles. Other steroids are only helpful when specific stimulation protocols are used. The level of some follicular proteins such as alpha-1-antitrypsin and fibrinogen also correlates with fertilization and pregnancy outcome. Cyclic AMP levels in follicular fluid are significantly reduced in follicles leading to conception. Regulators of oocyte maturation, such as the Oocyte Maturation Inhibitor (OMI) or the Meiosis Inducing Substance (MIS) have also been correlated with IVF outcome, but their exact structure remains still unknown. In addition, other sophisticated parameters, such as chemotactic activity of human leukocytes, or simple methods, such as the presence of intrafollicular echoes, have also been used as successful markers in predicting IVF outcome.

  13. Teaching Copywriting Students about the Mature Market.

    Science.gov (United States)

    Drewniany, Bonnie

    Advertising educators have a responsibility to make students aware of the importance of the mature market (older people) and to teach them methods to reach this group. An assignment in a copywriting class asked students to write and design ads to promote blue jeans to adults over 50. The assignment accomplished three things: (1) helped students…

  14. Plant regeneration in wheat mature embryo culture

    African Journals Online (AJOL)

    Kamil Haliloğlu

    2011-11-09

    Nov 9, 2011 ... Success in genetic engineering of cereals depends on the callus formation and efficient plant regeneration system. Callus formation and plant regeneration of wheat mature embryos ... compiled by modification of methods previously mentioned in ..... of more and readily available nutrition than artificial cul-.

  15. GROWTH PATTERNS AND MATURATION OF CHILDREN WITH ...

    African Journals Online (AJOL)

    GROWTH PATTERNS AND MATURATION OF CHILDREN WITH SICKLE CELL DISEASE IN RELATION TO PLASMA ZINC STATUS. Dr. Salwa R. El Batrawy, Dr. Mervat Tawfik M. Tantawi. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

  16. 7 CFR 51.2841 - Mature.

    Science.gov (United States)

    2010-01-01

    ... Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946... considered mature when harvested in accordance with good commercial practice at a stage which will not result...

  17. The influence of biological maturation on anthropometric ...

    African Journals Online (AJOL)

    The aim of this study was to determine whether biological maturation would significantly influence the anthropometric determinants of talent identification among U-14 provincial girl tennis players. Twenty-six of the top thirty-two provincial female players (mean age = 13.21± 0.72 years) from the Northern Gauteng and the ...

  18. 7 CFR 51.1823 - Mature.

    Science.gov (United States)

    2010-01-01

    ... Industry, Part 1, Chapter 20-13 Market Classification, Maturity Standards and Processing or Packing... Independence Ave., Washington, DC 20250 or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov...

  19. 7 CFR 51.767 - Mature.

    Science.gov (United States)

    2010-01-01

    ... Florida Citrus Industry, Part 1, Chapter 20-13 Market Classification, Maturity Standards and Processing or... 2065-S, 14th and Independence Ave., Washington, DC 20250 or at the National Archives and Records...: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. ...

  20. 7 CFR 51.1158 - Mature.

    Science.gov (United States)

    2010-01-01

    ... Citrus Industry, Part 1, Chapter 20-13 Market Classification, Maturity Standards and Processing or... 2065-S, 14th and Independence Ave., Washington, DC 20250 or at the National Archives and Records...: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. ...

  1. Analyzing Project Management Maturity Level in Indonesia

    Directory of Open Access Journals (Sweden)

    Eliot Simangunsong

    2013-04-01

    Full Text Available Project management has been generally known and increasingly used by many organizations to gain competitive advantage. In this context, many studies have proposed maturity models to evaluate how project management knowledge has been deployed effectively and efficiently in or- ganization. As a developing country, Indonesia needs many development projects managed by government and private companies in different industries. Here, a study to assess project manage- ment maturity level in Indonesian businesses may bring insight about current business practices, which is important to speed up country development and business sustainability. Adapting the Project Management Maturity Model (ProMMM, a survey instrument has been developed and ap- plied to professionals from Jakarta and surrounding area. The result of analysis shows that con- struction and primary industry have a higher maturity level compare to manufacturing and servic- es. It is to be noted, however, that the level of project management understanding is low across in- dustries. This indicates that more quality project management training or certification is required to improve overall project management knowledge in Indonesia.

  2. Distribution of aliphatic hydrocarbons, polycyclic aromatic hydrocarbons and organochlorinated pollutants in deep-sea sediments of the Southern Cretan margin, Eastern Mediterranean Sea: a baseline assessment.

    Science.gov (United States)

    Mandalakis, Manolis; Polymenakou, Paraskevi N; Tselepides, Anastasios; Lampadariou, Nikolaos

    2014-07-01

    Deep sediments from the southern Cretan margin were analyzed to establish baseline levels for various types of organic pollutants before the anticipated intensification of anthropogenic activities. The total concentration of aliphatic hydrocarbons (ΣAH:326-3758ngg(-1), dry weight) was similar to those reported for deep sediments of the western Mediterranean Sea, while considerably lower levels were measured for polycyclic aromatic hydrocarbons (ΣPAH:9-60ngg(-1)). Source-diagnostic ratios suggested that the aliphatic hydrocarbons in sediments were mainly of terrestrial biogenic origin, while polycyclic aromatic hydrocarbons stemmed from the deposition of long-range transported combustion aerosols. Among the organochlorinated compounds analyzed, β-hexachlorocyclohexane (β-HCH:222-7052pgg(-1)), 1,1,1-trichloro-2,2-bis(4-chlorophenyl)ethane (p,p'-DDT:37-2236pgg(-1)) and polychlorinated biphenyls (ΣPCB:38-1182pgg(-1)) showed the highest abundance in sediments. The presence of HCHs and PCBs was attributed to historical inputs that have undergone extensive weathering, whereas an ongoing fresh input was suggested for p,p'-DDT. Multiple linear regression analysis revealed that the levels of the various pollutants in sediments were controlled by different factors, but with organic carbon content playing a prominent role in most cases. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. Can hydrocarbons entrapped in seep carbonates serve as gas geochemistry recorder?

    Science.gov (United States)

    Blumenberg, Martin; Pape, Thomas; Seifert, Richard; Bohrmann, Gerhard; Schlömer, Stefan

    2018-04-01

    The geochemistry of seep gases is useful for an understanding of the local petroleum system. Here it was tested whether individual light hydrocarbons in seep gases are representatively entrapped in authigenic carbonates that formed near active seep sites. If applicable, it would be possible to extract geochemical information not only on the origin but also on the thermal maturity of the hydrocarbon source rocks from the gases entrapped in carbonates in the past. Respective data could be used for a better understanding of paleoenvironments and might directly serve as calibration point for, amongst others, petroleum system modeling. For this approach, (sub)-recent seep carbonates from the Black Sea (Paleodnjepr region and Batumi seep area), two sites of the Campeche Knoll region in the Gulf of Mexico, and the Venere mud volcano (Mediterranean Sea) were selected. These seep carbonates derive from sites for which geochemical data on the currently seeping gases exist. During treatment with phosphoric acid, methane and higher hydrocarbons were released from all carbonates, but in low concentrations. Compositional studies demonstrate that the ratio of methane to the sum of higher hydrocarbons (C1/(C2+C3)) is (partly strongly) positively biased in the entrapped gas fraction. δ13C values of C1 were determined for all samples and, for the samples from the Gulf of Mexico and the Mediterranean Sea, also of C2 and C3. The present dataset from six seep sites indicates that information on the seeped methane can be—although with a scatter of several permil—recorded in seep carbonate matrices, but other valuable information like the composition and δ13C of ethane and propane appears to be modified or lost during, for example, enclosure or at an early stage of diagenesis.

  4. Maturation of human oocytes in vitro

    Directory of Open Access Journals (Sweden)

    Mojca Čižek-Sajko

    2007-01-01

    Full Text Available Background: Immature oocyte retrieval followed by in vitro maturation is a promising infertility treatment option. In patients with morphologically normal ovaries and regular menstrual cycles and in patients with polycystic ovary syndrome (PCOS we attempted to assess the success of oocyte in vitro maturation in in vitro fertilization (IVF procedures.Methods: Retrospectively we analyzed 87 IVF procedures with in vitro maturation of oocytes carried out in 73 infertile couples treated at the Maribor Teaching Hospital. We compared the success following three different hormone priming protocols: regular cycling patients with normal ovaries and without hormone priming (Group A, n = 27; patients with PCOS and hormone priming with follitropin (follicle stimulating hormone, FSH (Group B, n = 22; patients with PCOS and hormone priming with human chorionic gonadotrophin (hCG (Group C, n = 38. Success of the procedure was evaluated on the basis of the ability of oocytes to mature, fertilize and develop into embryos, and on the basis of the quality of embryos and their ability to implant in the uterus.Results: In regular cycling patients with normal ovaries (n = 27 we obtained a significantly lower number of immature oocytes (3.2 ± 2.5 compared with patients with PCOS and FSH priming (11.7 ± 7.2 or those with PCOS and hCG priming (10.4 ± 7.2. The oocyte maturation rate, the fertilization rate and the embryo cleavage rate were as follows: in Group A 57.7 %, 63.2 % and 91.7 %, in Group B 57.6 %, 66.2 % and 90.0 %, and in Group C 58.0 %, 66.2 % and 91.0 % (the differences between groups were not statistically significant. Six pregnancies were recorded only in patients with PCOS. The pregnancy rate per embryo transfer was 1/20 (5.0 % in patients with FSH priming, and 5/33 (15.2 % in patients with hCG priming.Conclusions: Oocyte in vitro maturation is successful in patients with normal ovaries and regular menstrual cycle as well as in those with polycystic

  5. Velocity Dependence of Friction of Confined Hydrocarbons

    DEFF Research Database (Denmark)

    Sivebæk, Ion Marius; Samoilov, Vladimir N.; Persson, Bo N. J.

    2010-01-01

    We present molecular dynamics friction calculations for confined hydrocarbon “polymer” solids with molecular lengths from 20 to 1400 carbon atoms. Two cases are considered: (a) polymer sliding against a hard substrate and (b) polymer sliding on polymer. We discuss the velocity dependence of the f......We present molecular dynamics friction calculations for confined hydrocarbon “polymer” solids with molecular lengths from 20 to 1400 carbon atoms. Two cases are considered: (a) polymer sliding against a hard substrate and (b) polymer sliding on polymer. We discuss the velocity dependence...... of the frictional shear stress for both cases. In our simulations, the polymer films are very thin (∼3 nm), and the solid walls are connected to a thermostat at a short distance from the polymer slab. Under these circumstances we find that frictional heating effects are not important, and the effective temperature...... in the polymer film is always close to the thermostat temperature. In the first setup (a), for hydrocarbons with molecular lengths from 60 to 1400 carbon atoms, the shear stresses are nearly independent of molecular length, but for the shortest hydrocarbon C20H42 the frictional shear stress is lower. In all...

  6. Taxation on mining and hydrocarbon investments

    Directory of Open Access Journals (Sweden)

    Beatriz De La Vega Rengifo

    2014-07-01

    Full Text Available This article comments the most important aspects of the tax treatment applicable to investments of mining and oil and gas industry. The document highlights the relevant tax topics of the general tax legislation(Income Tax Law and the special legislation of both industries (General Mining Law and Hydrocarbons Organic Law.

  7. Hydrocarbons in Argentina: networks, territories, integration

    International Nuclear Information System (INIS)

    Carrizo, S.C.

    2003-12-01

    Argentinean hydrocarbons networks have lived a huge reorganizing the structure, after the State reform in the 90's. Activities deregulation and the privatization of YPF and Gas del Estado forced the sector re-concentration, since then dominated by foreign companies, leaded by Repsol YPF. The hydrocarbons federalization contributed to the weakening and un-capitalization loss of wealth of the State. These changes resulted in an increase of the hydrocarbons production allowing to achieve the self-supply. Nevertheless, the expansion of internal networks has not been large enough to ensure the coverage of new requirements. Besides, several infrastructures have been built up to join external markets. National networks are connected to those of near neighboring countries. This integration is an opportunity for the 'South Cone' countries to enhance their potentials. In the country, hydrocarbons territories undergo the reorganizing the structure effects (unemployment, loss of territorial identity, etc). With many difficulties and very different possibilities, those territories, like Comodoro Rivadavia, Ensenada et and Bahia Blanca, look for their re-invention. (author)

  8. Cuticle hydrocarbons in saline aquatic beetles

    Directory of Open Access Journals (Sweden)

    María Botella-Cruz

    2017-07-01

    Full Text Available Hydrocarbons are the principal component of insect cuticle and play an important role in maintaining water balance. Cuticular impermeability could be an adaptative response to salinity and desiccation in aquatic insects; however, cuticular hydrocarbons have been poorly explored in this group and there are no previous data on saline species. We characterized cuticular hydrocarbons of adults and larvae of two saline aquatic beetles, namely Nebrioporus baeticus (Dytiscidae and Enochrus jesusarribasi (Hydrophilidae, using a gas chromatograph coupled to a mass spectrometer. The CHC profile of adults of both species, characterized by a high abundance of branched alkanes and low of unsaturated alkenes, seems to be more similar to that of some terrestrial beetles (e.g., desert Tenebrionidae compared with other aquatic Coleoptera (freshwater Dytiscidae. Adults of E. jesusarribasi had longer chain compounds than N. baeticus, in agreement with their higher resistance to salinity and desiccation. The more permeable cuticle of larvae was characterized by a lower diversity in compounds, shorter carbon chain length and a higher proportion of unsaturated hydrocarbons compared with that of the adults. These results suggest that osmotic stress on aquatic insects could exert a selection pressure on CHC profile similar to aridity in terrestrial species.

  9. Wireless sensing on surface hydrocarbon production systems

    International Nuclear Information System (INIS)

    Kane, D; McStay, D; Mulholland, J; Costello, L

    2009-01-01

    The use of wireless sensor networks for monitoring and optimising the performance of surface hydrocarbon production systems is reported. Wireless sensor networks are shown to be able to produce comprehensively instrumented XTs and other equipment that generate the data required by Intelligent Oilfield systems. The information produced by such systems information can be used for real-time operational control, production optimization and troubleshooting.

  10. Toxic Potential of Carcinogenic Polycyclic Aromatic Hydrocarbons ...

    African Journals Online (AJOL)

    Toxic Potential of Carcinogenic Polycyclic Aromatic Hydrocarbons (cPAHs) and Heavy Metal in Crude Oil from Gokana Area, Rivers State, Nigeria. ... Considerable caution should be applied in exploration, exposure and distribution of the crude oil through protected and well maintained pipelines to avoid the possible ...

  11. Earthworm-assisted bioremediation of petroleum hydrocarbon ...

    African Journals Online (AJOL)

    Ameh

    The use of earthworms (Eudrilus eugenia) for vermi-assisted bioremediation of petroleum hydrocarbon contaminated mechanic workshop soils ... not always result in complete neutrali- zation of pollutants (Yerushalmi et al., 2003). ..... Screening of biofouling activity in marine bacterial isolate from ship hull. Int. J. Environ. Sci.

  12. Petroleum-hydrocarbons biodegradation by Pseudomonas strains ...

    African Journals Online (AJOL)

    The capability of these isolates to degrade petroleum was performed by measuring the optical density, colony forming unit counts (CFU/ml) and concentration of total petroleum hydrocarbons (TPH). Degradation of Isomerate by these isolates was analyzed by gas chromatography with flame ionization detector (FID). Results ...

  13. Polycyclic Aromatic Hydrocarbons (PAHs) Levels in Two ...

    African Journals Online (AJOL)

    Polycyclic aromatic hydrocarbons (PAHs) concentrations were measured by gas chromatography with flame ionization detector (GC/FID) in two fish species, Sardinella maderensis (Flat sardinella) and Galeoides decadactylus (Lesser African threadfin or Shine-nose or Common threadfin) from Ghanaian coastal waters and ...

  14. Bioremediation of Polycyclic Aromatic Hydrocarbon contaminated ...

    African Journals Online (AJOL)

    This study investigates the effect of lead and chromium on the rate of bioremediation of polycyclic aromatic hydrocarbon (PAH) contaminated clay soil. Naphthalene was used as a target PAH. The soil was sterilized by heating at 120oC for one hour. 100g of the soil was contaminated with lead, chromium, nickel and mercury ...

  15. Determination of carcinogenic polycyclic aromatic hydrocarbons in ...

    African Journals Online (AJOL)

    Determination of carcinogenic polycyclic aromatic hydrocarbons in air samples in Irbid, north Jordan. A Al-Gawadreh Sat, M.B. Gasim, A.R. Hassan, A Azid. Abstract. Air samples were collected at an urban site and a rural (BERQESH) site during February (2017) until March (2017) to determine concentrations of polycyclic ...

  16. Determination of carcinogenic polycyclic aromatic hydrocarbons ...

    African Journals Online (AJOL)

    Log in or Register to get access to full text downloads. ... collected from the most polluted part of Bangsai river at Saver industrial zone was analyzed for the presence of polycyclic aromatic hydrocarbon, anthracene, by gas chromatography-mass spectrometry (GC-MS). A ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

  17. The role of hydrocarbons in energy transition

    International Nuclear Information System (INIS)

    2015-11-01

    This publication presents some reflections and statements as well as data regarding the role of hydrocarbons in energy production and consumption, in order to better highlight the role hydrocarbons may have in energy transition. It outlines the still very important share of oil in primary and final energy, and more particularly in transports, and that, despite the development of other energies, an energy transition is always very slow. It discusses the perspectives for hydrocarbon reserves and production of oil and natural gas. It outlines that oil remains the most important energy for mobility, the benefits of conventional fuels, and that distribution infrastructures must be preserved and developed. It discusses the evolution of the economic situation of the refining activity (more particularly its margin). It outlines the high contribution of oil industry to economic activity and employment in France, discusses the French energy taxing policy and environmental taxing policy, discusses the issue of security of energy supply (with its different components: exploration-production, refining, logistics and depots, distribution and station network). It discusses the possible role shale hydrocarbons may have in the future. For each issue, the position and opinion of the UFIP (the French Union of oil industries) is stated. The second part of the document proposes a Power Point presentation with several figures and data on these issues

  18. Mathematical modelling on transport of petroleum hydrocarbons

    Indian Academy of Sciences (India)

    A brief theory has been included on the composition and transport of petroleum hydrocarbons following an onshore oil spill in order to demonstrate the level of complexity associated with the LNAPL dissolution mass transfer even in a classical porous medium. However, such studies in saturated fractured rocks are highly ...

  19. Oxygenation of saturated and unsaturated hydrocarbons with ...

    Indian Academy of Sciences (India)

    Unknown

    Oxygenation of saturated and unsaturated hydrocarbons with sodium periodate. 431. Table 1. Competitive oxygenation of tetralin and cyclooctene with sodium periodate catalyzed by different manga- .... Teacher Education University. My grateful thanks also extend to Dr D Mohajer for his useful sugges- tions. References. 1.

  20. Process of converting phenols into hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Seelig, S

    1929-02-02

    A process is disclosed for the conversion of phenols into hydrocarbons, characterized by preheating a mixture of phenols and hydrogen or hydrogen-producing gases to approximately the reaction temperature under pressure, heating by passage percussion-like through a bath of metal to the reaction temperature, and rapidly cooling.