Analyzing tree cores to detect petroleum hydrocarbon-contaminated groundwater at a former landfill site in the community of Happy Valley-Goose Bay, eastern Canadian subarctic.

Science.gov (United States)

Fonkwe, Merline L D; Trapp, Stefan

2016-08-01

This research examines the feasibility of analyzing tree cores to detect benzene, toluene, ethylbenzene, and m, p, o-xylene (BTEX) compounds and methyl tertiary-butyl ether (MTBE) in groundwater in eastern Canada subarctic environments, using a former landfill site in the remote community of Happy Valley-Goose Bay, Labrador. Petroleum hydrocarbon contamination at the landfill site is the result of environmentally unsound pre-1990s disposal of households and industrial solid wastes. Tree cores were taken from trembling aspen, black spruce, and white birch and analyzed by headspace-gas chromatography-mass spectrometry. BTEX compounds were detected in tree cores, corroborating known groundwater contamination. A zone of anomalously high concentrations of total BTEX constituents was identified and recommended for monitoring by groundwater wells. Tree cores collected outside the landfill site at a local control area suggest the migration of contaminants off-site. Tree species exhibit different concentrations of BTEX constituents, indicating selective uptake and accumulation. Toluene in wood exhibited the highest concentrations, which may also be due to endogenous production. Meanwhile, MTBE was not found in the tree cores and is considered to be absent in the groundwater. The results demonstrate that tree-core analysis can be useful for detecting anomalous concentrations of petroleum hydrocarbons, such as BTEX compounds, in subarctic sites with shallow unconfined aquifers and permeable soils. This method can therefore aid in the proper management of contamination during landfill operations and after site closures.

Identifying the source of petroleum pollution in sediment cores of southwest of the Caspian Sea using chemical fingerprinting of aliphatic and alicyclic hydrocarbons.

Science.gov (United States)

Shirneshan, Golshan; Bakhtiari, Alireza Riyahi; Memariani, Mahmoud

2017-02-15

In this study, the concentration and sources of aliphatic and petroleum markers were investigated in 105 samples of Anzali, Rezvanshahr and Astara cores from the southwest of Caspian Sea. Petroleum importation was diagnosed as a main source in most depths of cores by the results of unresolved complex mixture, carbon preference index and hopanes and steranes. From the chemical diagnostic parameters, petroleum inputs in sediment of cores were determined to be different during years and the sources of hydrocarbons in some sections differed than Anzali and Turkmenistan and Azerbaijan oils. Diagenic ratios in most sediments of upper and middle sections in Astara core were determined to be highly similar to those of Azerbaijan oil, while the presence of Turkmenistan and Anzali oils were detected in a few sections of Anzali and Rezvanshahr cores and only five layers of downer section in Anzali core, respectively. Copyright © 2016. Published by Elsevier Ltd.

Can hydrocarbons in coastal sediments be related to terrestrial flux? A case study of Godavari river discharge (Bay of Bengal)

Digital Repository Service at National Institute of Oceanography (India)

Rayaprolu, K.; GopalaKrishna, V.V.J.; Naik, B.G.; Mahalakshmi, G.; Rengarajan, R.; Mazumdar, A; Sarma, N.S.

A sediment core aged ~250 years and deposition rate of ~2.4 mm yr^-1 raised from the coastal region receiving inputs from the Godavari river was examined for n-alkanes The carbon preference index (CPI) of shortchain hydrocarbons (SHC...

Pre-Alleghenian (Pennsylvanian-Permian) hydrocarbon emplacement along Ordovician Knox unconformity, eastern Tennessee

Energy Technology Data Exchange (ETDEWEB)

Haynes, F.M.; Kesler, S.E.

1989-03-01

Cores taken during exploration for Mississippi Valley-type lead and zinc ores in the Mascot-Jefferson City zinc district of eastern Tennessee commonly contain hydrocarbon residues in carbonate rocks of the Knox Group immediately below the Lower Ordovician Knox unconformity. The location and number of these residue-bearing strata reveal information about the Paleozoic history of hydrocarbon emplacement in the region. Contour maps, generated from nearly 800 holes covering more than 20 km/sup 2/, indicate that zones with elevated organic content in the uppermost 30 m of the Lower Ordovician Mascot Dolomite show a strong spatial correlation with Middle Ordovician paleotopographic highs. These same zones show no spatial association with present-day structural highs, which were formed during Pennsylvanian-Permian Alleghenian tectonism. This suggests that the physical entrapment of hydrocarbons migrating through the upper permeable units of the Mascot must have occurred prior to the principal tectonism of the Alleghenian orogeny. 7 figures, 1 table.

Sensitivity ranking for freshwater invertebrates towards hydrocarbon contaminants.

Science.gov (United States)

Gerner, Nadine V; Cailleaud, Kevin; Bassères, Anne; Liess, Matthias; Beketov, Mikhail A

2017-11-01

Hydrocarbons have an utmost economical importance but may also cause substantial ecological impacts due to accidents or inadequate transportation and use. Currently, freshwater biomonitoring methods lack an indicator that can unequivocally reflect the impacts caused by hydrocarbons while being independent from effects of other stressors. The aim of the present study was to develop a sensitivity ranking for freshwater invertebrates towards hydrocarbon contaminants, which can be used in hydrocarbon-specific bioindicators. We employed the Relative Sensitivity method and developed the sensitivity ranking S hydrocarbons based on literature ecotoxicological data supplemented with rapid and mesocosm test results. A first validation of the sensitivity ranking based on an earlier field study has been conducted and revealed the S hydrocarbons ranking to be promising for application in sensitivity based indicators. Thus, the first results indicate that the ranking can serve as the core component of future hydrocarbon-specific and sensitivity trait based bioindicators.

Analyzing tree cores to detect petroleum hydrocarbon-contaminated groundwater at a former landfill site in the community of Happy Valley-Goose Bay, eastern Canadian subarctic

DEFF Research Database (Denmark)

Fonkwe, Merline L D; Trapp, Stefan

2016-01-01

-gas chromatography-mass spectrometry. BTEX compounds were detected in tree cores, corroborating known groundwater contamination. A zone of anomalously high concentrations of total BTEX constituents was identified and recommended for monitoring by groundwater wells. Tree cores collected outside the landfill site......This research examines the feasibility of analyzing tree cores to detect benzene, toluene, ethylbenzene, and m, p, o-xylene (BTEX) compounds and methyl tertiary-butyl ether (MTBE) in groundwater in eastern Canada subarctic environments, using a former landfill site in the remote community of Happy...... Valley-Goose Bay, Labrador. Petroleum hydrocarbon contamination at the landfill site is the result of environmentally unsound pre-1990s disposal of households and industrial solid wastes. Tree cores were taken from trembling aspen, black spruce, and white birch and analyzed by headspace...

Distribution of hydrocarbon-utilizing microorganisms and hydrocarbon biodegradation potentials in Alaskan continental shelf areas

International Nuclear Information System (INIS)

Roubal, G.; Atlas, R.M.

1978-01-01

Hydrocarbon-utilizing microogranisms were enumerated from Alaskan continental shelf areas by using plate counts and a new most-probable-number procedure based on mineralization of 14 C-labeled hydrocarbons. Hydrocarbon utilizers were ubiquitously distributed, with no significant overall concentration differences between sampling regions or between surface water and sediment samples. There were, however, significant seasonal differences in numbers of hydrocarbon utilizers. Distribution of hydrocarbon utilizers within Cook Inlet was positively correlated with occurrence of hydrocarbons in the environment. Hydrocarbon biodegradation potentials were measured by using 14 C-radiolabeled hydrocarbon-spiked crude oil. There was no significant correlation between numbers of hydrocarbon utilizers and hydrocarbon biodegradation potentials. The biodegradation potentials showed large seasonal variations in the Beaufort Sea, probably due to seasonal depletion of available nutrients. Non-nutrient-limited biodegradation potentials followed the order hexadecane > naphthalene >> pristane > benzanthracene. In Cook Inlet, biodegradation potentials for hexadecane and naphthalene were dependent on availability of inorganic nutrients. Biodegradation potentials for pristane and benzanthracene were restricted, probably by resistance to attack by available enzymes in the indigenous population

Hydrocarbon formation core protection and and transportation apparatus

NARCIS (Netherlands)

2013-01-01

An apparatus for transporting core samples includes an outer tube having an open end and a cover removably mounted to the open end; a core tube slidable into and out ofthe outer tube when the cover is removed from the outer tube; and a stabilizing structure between the core tube and the outer tube,

Polycyclic Aromatic Hydrocarbons (PAHs in the atmosphere of the Baltic Sea Region

Directory of Open Access Journals (Sweden)

Julia Gaffke

2016-03-01

Full Text Available The paper presents a review of publications on the concentrations of polycyclic aromatic hydrocarbons in the atmosphere of the Baltic Sea Region (BSR. It indicates the main emission sources of these substances, related to anthropogenic activity. These include incomplete combustion of fuels in engines on land and from marine transportation, as well as the burning of coal in the community sector. High PAH concentrations in the air are also related to increased industrial activity in urban areas. In the Baltic Sea Region, Germany and Poland have been determined to be responsible for the greatest proportion of PAH emissions. However, the highest number of exceedances of the accepted annual norm for benzo(apyrene concentrations was recorded in Poland.

Trace elements in a North Sea drill core

DEFF Research Database (Denmark)

Kunzendorf, Helmar; Gwozdz, R.; Svendsen, N.

1986-01-01

, V, Sr, Dy, Mg, Ti, Ba and Eu. The major elements Ca and Al could be related to petrophysical parameters, particularly Al which shows a correlation with the silicification/argillaceous content. Na (and Cl) has a low content in the hydrocarbon-bearing section of the drill core suggesting that the pore......Chalk samples, systematically taken along a drill core from one of the hydrocarbon producing fields of the North Sea (Tyra field), were analysed by a neutron activation technique involving measurement of radioisotopes with relatively short half-lives. Elements determined include Na, Al, Cl, Ca, Mn...... space is filled mainly by hydrocarbons. A significant decrease of Mn with depth probably suggests diagenesis of chalk prior to, or with, hydrocarbon emplacement. Investigations of drilling fluids and cuttings reveal a strong contamination of the latter, mainly by Ba. Chalk data from comparable onshore...

Magnetotelluric Studies for Hydrocarbon and Geothermal Resources: Examples from the Asian Region

Science.gov (United States)

Patro, Prasanta K.

2017-09-01

Magnetotellurics (MT) and the other related electrical and electromagnetic methods play a very useful role in resource exploration. This review paper presents the current scenario of application of MT in the exploration for hydrocarbons and geothermal resources in Asia. While seismics is the most preferred method in oil exploration, it is, however, beset with several limitations in the case of sedimentary targets overlain by basalts or evaporate/carbonate rocks where the high-velocity layers overlying the lower velocity layers pose a problem. In such cases, MT plays an important and, in some cases, a crucial role in mapping these potential reservoirs because of significant resistivity contrast generally observed between the basalts and the underlying sedimentary layers. A few case histories are presented that typically illustrate the role of MT in this context. In the case of geothermal exploration, MT is known to be highly effective in deciphering the target areas because of the conductivity structures arising from the presence and circulation of highly conductive fluids in the geothermal target areas. A few examples of MT studies carried out in some of the potential areas of geothermal significance in the Asian region are also discussed. While it is a relatively favorable situation for application of EM and MT methods in the case of exploration of the high-enthalpy region due to the development of well-defined conceptual models, still the low-enthalpy regions need to be understood well, particularly because of more complex structural patterns and the fluid circulation under relatively low-temperature conditions. Currently, a lot of modeling in both geothermal and hydrocarbon exploration is being done using three-dimensional techniques, and it is the right time to go for integration and three-dimensional joint inversion of the geophysical parameters such as resistivity, velocity, density, from MT, electromagnetics (EM), seismics and gravity.

Coupled core criticality calculations with control rods located in the central reflector region

Energy Technology Data Exchange (ETDEWEB)

Sobhy, M [Reactor depatrment, nuclear research center, Inshaas (Egypt)

1995-10-01

The reactivity of a coupled core is controlled by a set of control rods distributed in the central reflector region. The reactor contains two compact cores cooled and moderated by light water. Control rods are designed to have reactivity worths sufficient to start, control and shutdown the coupled system. Each core in a coupled system is in subcritical conditions without any absorber then each core needs to the other core to fulfill nuclear chain reaction and to approach the criticality. In this case, each core is considered clean which is suitable for research reactor with low flux disturbance and better neutron economy, in addition to the advantage of disappearing the cut corner fuel baskets. This facilitate the in core fuel management with identical fuel baskets. Hot spots will disappear. This leads to a good heat transfer process. the excess reactivity and the shutdown margin are calculated for some of reflector as coupling region gives sufficient area for coupled core are calculated cost. The fluctuations of reactivity for coupled core are calculated by noise analysis technique and compared with that for rode core. The results show low reactivity perturbation associated with coupled core.

Linking biochemical perturbations in tissues of the African catfish to the presence of polycyclic aromatic hydrocarbons in Ovia River, Niger Delta region.

Science.gov (United States)

Obinaju, Blessing E; Graf, Carola; Halsall, Crispin; Martin, Francis L

2015-06-01

Petroleum hydrocarbons including polycyclic aromatic hydrocarbons (PAHs) are a pollution issue in the Niger Delta region due to oil industry activities. PAHs were measured in the water column of the Ovia River with concentrations ranging from 0.1 to 1055.6 ng L(-1). Attenuated total reflection Fourier-transform infrared (ATR-FTIR) spectroscopy detected alterations in tissues of the African catfish (Heterobranchus bidorsalis) from the region showed varying degrees of statistically significant (Pinfrared spectroscopy in environmental studies and supports their potential application in biomonitoring. Copyright © 2015 Elsevier Ltd. All rights reserved.

Petroleum hydrocarbon concentrations in marine sediments along Chennai Coast, Bay of Bengal, India.

Science.gov (United States)

Venkatachalapathy, R; Veerasingam, S; Ramkumar, T

2010-10-01

The spatial and temporal distribution of petroleum hydrocarbons (PHC) in marine sediments along the Chennai coast, Bay of Bengal was quantified by Ultra-Violet Fluorescence (UVF) Spectroscopy. The concentration of PHC in surface sediments varied from 1.88 to 39.76 ppm. The highest values obtained in the northern part of the study area, where shipping activities and land-based waste waters disposed into sea through the rivers like Kuvam and Adayar. The Adayar (7.26-16.83 ppm) and Kuvam (5.5-39.72 ppm) cores reveal a clear horizon of increase in PHC above 50 and 35 cm respectively. PHC values showed a decreasing pattern with depth in all sediment cores suggesting the excess anthropogenic loading occurring in the recent past. The present study revealed that the PHC values of Chennai coastal sediments are lower than the values reported from selected costal areas including the sediment of the Mumbai coast (7.6-42.8 ppm), Arabian Sea. The results will be useful for pollution monitoring program along the coastal region and also to check the level of petroleum hydrocarbons in marine sediments.

Numerical analysis of temperature fluctuation in core outlet region of China experimental fast reactor

International Nuclear Information System (INIS)

Zhu Huanjun; Xu Yijun

2014-01-01

The temperature fluctuation in core outlet region of China Experimental Fast Reactor (CEFR) was numerically simulated by the CFD software Star CCM+. With the core outlet temperatures, flows etc. under rated conditions given as boundary conditions, a 1/4 region model of the reactor core outlet region was established and calculated using LES method for this problem. The analysis results show that while CEFR operates under rated conditions, the temperature fluctuation in lower part of core outlet region is mainly concentrated in area over the edge components (steel components, control rod assembly), and one in upper part is remarkable in area above all the components. The largest fluctuation amplitude is 19 K and the remarkable frequency is below 5 Hz, and it belongs to typically low frequency fluctuation. The conclusion is useful for further experimental work. (authors)

Biogenic non-methane hydrocarbons (NMHC). Nature`s contribution to regional and global atmospheric chemistry

Energy Technology Data Exchange (ETDEWEB)

Klockow, D.; Hoffman, T. [Inst. of Spectrochemistry and Applied Spectroscopy, Dortmund (Germany)

1995-12-31

Terrestrial vegetation provides an important source of volatile hydrocarbons, especially isoprene, monoterpenes and in addition possibly sesquiterpenes as well as oxygenated compounds. Although there exist considerable uncertainties in the estimation of the magnitude of these biogenic NMHC emissions, it is generally accepted that the majority of global NMHC release is from natural and not from anthropogenic sources. Taking into consideration the high reactivity of the mostly unsaturated biogenic emissions, their impact on tropospheric processes can be assumed to be of great importance. Together with anthropogenic NO{sub x} emissions, the highly reactive natural alkenes can act as precursors in photochemical oxidant formation and contribute to regional-scale air pollution. Their oxidation in the atmosphere and the subsequent gas-to-particle conversion of the products lead to the formation of organic aerosols. Because of the formation of phytotoxic compounds, the interaction of the biogenic hydrocarbons with ozone inside or outside the leaves and needles of plants has been suggested to play a role in forest decline. (author)

Biogenic non-methane hydrocarbons (NMHC). Nature`s contribution to regional and global atmospheric chemistry

Energy Technology Data Exchange (ETDEWEB)

Klockow, D; Hoffman, T [Inst. of Spectrochemistry and Applied Spectroscopy, Dortmund (Germany)

1996-12-31

Terrestrial vegetation provides an important source of volatile hydrocarbons, especially isoprene, monoterpenes and in addition possibly sesquiterpenes as well as oxygenated compounds. Although there exist considerable uncertainties in the estimation of the magnitude of these biogenic NMHC emissions, it is generally accepted that the majority of global NMHC release is from natural and not from anthropogenic sources. Taking into consideration the high reactivity of the mostly unsaturated biogenic emissions, their impact on tropospheric processes can be assumed to be of great importance. Together with anthropogenic NO{sub x} emissions, the highly reactive natural alkenes can act as precursors in photochemical oxidant formation and contribute to regional-scale air pollution. Their oxidation in the atmosphere and the subsequent gas-to-particle conversion of the products lead to the formation of organic aerosols. Because of the formation of phytotoxic compounds, the interaction of the biogenic hydrocarbons with ozone inside or outside the leaves and needles of plants has been suggested to play a role in forest decline. (author)

Relationship between polycyclic aromatic hydrocarbons (PAHs) and particle size in dated core sediments in Lake Lianhuan, Northeast China

International Nuclear Information System (INIS)

Sun, Li; Zang, Shuying

2013-01-01

Atmospheric particle associated with pyrogenic polycyclic aromatic hydrocarbons (PAHs) poses serious threats to human health by inhalation exposure, especially in semiarid areas. Hence, the distributions of PAHs and particle size in two core sediments collected from Lake Lianhuan, Northeast China were studied. The sediments were dated radiometrically, and particle size distribution and PAH concentration were evaluated and potential human health risk was assessed. From 1980 to 2007, the dominant PAHs in the two cores were 2- and 3-ring PAHs, and the concentrations of 3–6 ring PAHs gradually increased from the early 1990s. Diagnostic ratios indicated that pyrogenic PAHs were the main sources of PAHs which changed over time from combustions of wood and coal to liquid fossil fuel sources. Fine particles ( 125 μm were found. Future research should focus on the seven carcinogenic pyrogenic PAHs due to a rapidly increasing trend since 1995 based on the assessment of toxic equivalency factors. - Highlights: • PAHs and particle size in core sediments were used to evaluate the role of eolian particles in delivering pyrogenic PAHs. • Changes of PAH sources closely followed local historical socioeconomic development since 1980s. • Changes of particulate sources from eolian to lacustrine reflected the evolving history of the lake. • Significant correlations between pyrogenic PAHs and eolian particles indicated potential risk from inhalation exposure. • Petroleum source PAHs are likely to stick to coarse particles and accumulate in lake sediments by surface runoff

Financial and Organizational Aspects of the Recovery of Hydrocarbon Resource Base in the Regional Context

Directory of Open Access Journals (Sweden)

Irina Valeryevna Sharf

2017-06-01

Full Text Available The characteristics of hydrocarbon resource base qualitative and quantitative degrade are reflected in the increase of the share of small and medium−sized deposits, as well as hard−to−recover reserves. This makes the need to update the approaches to the implementation of the geological prospecting programmes. The geological exploration performance differs in oil−producing regions of the Russian Federation due to a number of various factors. The subject matter of the study is the assessment of the strength of these factors in various working, geological, infrastructure and economic conditions to determine the effectiveness of the existing economic model of the recovery of hydrocarbon resource base, as well as to develop the author’s suggestions. The hypothesis of the study proposes to change the economic, as well as financial and tax mechanisms of government regulation of the geological exploration, carried out by small oil producing companies on license areas with one or several fields in order to stimulate the development of hydrocarbon resource base. The method of the study is the correlation analysis of the impact of various factors on geological exploration on mineral resource base recovery. It is carried out utilizing K. Mohn model and the statistical data of three subjects of the Russian Federation (the Republic of Tatarstan, Khanty−Mansiysk Autonomous District and Tomsk region. The results of the study can be applied in the tax and financial legislation, as well as in the management of oil and gas industry in the field of geological exploration. On the basis of the conducted analysis and international experience, the author suggests to introduce reasonable tax incentives and the mechanism of public private partnership in the realization of geological prospecting programmes with the aim to support small oil producing companies at the initial stage of the development of a field.

[Heavy metals and hydrocarbons content in soils of settlements of the Yamal-Nenets autonomous region].

Science.gov (United States)

Alekseev, I I; Abakumov, E V; Shamilishvili, G A; Lodygin, E D

In August 2015 there were executed investigations on the study of the soils diversity of the Yamal-Nenets Autonomous Okrug. One of the directions of this work got be the study of urban soils of settlements of the Yamal-Nenents Autonomous Okrug. The sectors for the observation were settlement of Harsaim, village Aksarka, city of Salekhard, settlement Harp and city of Labytnangi. About 20 soil samples were collected during the field work. Samples were collected from a depth of 0-5 cm and 5-20 cm. Heavy metals (HM) were detected with the use of X-ray fluorescent analyzer “Spectroscan-MAX”. The HM content values were compared with the corresponding Approxible Permissible Concentrations and Maximum Allowable Concentrations (MAC) adopted in Russia. Hydrocarbons content was determined by gravimetric method. Values of the hydrocarbons content in studied soils were compared with the existing regulations of the Russian Federation. The levels of soil contamination by hydrocarbons were determined. The study of soil samples from different settlements allowed to reveal characteristic features of soil contamination of separate settlements by HM and hydrocarbons and to compare them against each other. The vast majority of samples are characterized by arsenic exceedance of MAC, which should indicate to a high regional background of this element. For a more adequate assessment of the Zc meaning as the value of the total pollution index of soils there were used not only arithmetical average values of the coefficients of the chemical composition concentration (Kc), but also their average geometric values. According to levels of total soil contamination most of soil samples are characterized as non-hazardous (Zc<16). Calculation of soil pollution index showed that the most of soil samples have values less than 1. It characterizes soils as unpolluted. Statistical processing of obtained data in the media of the analytical software interface STATISTICA 10 showed a statistically

Stability region for a prompt power variation of a coupled-core system with positive prompt feedback

International Nuclear Information System (INIS)

Watanabe, S.; Nishina, K.

1984-01-01

A stability analysis using a one-group model is presented for a coupled-core system. Positive prompt feedback of a γp /SUB j/ form is assumed, where p /SUB j/ is the fractional power variation of core j. Prompt power variations over a range of a few milliseconds after a disturbance are analyzed. The analysis combines Lapunov's method, prompt jump approximation, and the eigenfunction expansion of coupling region response flux. The last is treated as a pseudo-delayed neutron precursor. An asymptotic stability region is found for p /SUB j/. For an asymmetric flux variation over a system of two coupled cores, either p /SUB I/ or p /SUB II/ can slightly exceed, by virtue of the coupling effect, the critical value (β/γ-1) of a single-core case. Such a stability region is increased by additional inclusion of the coupling region fundamental mode in the treatment. The coupling region contributes to stability through its delayed response and coupling. An optimum core separation distance for stability is found

Task 8: Evaluation of hydrocarbon potential

International Nuclear Information System (INIS)

Cashman, P.H.; Trexler, J.H. Jr.

1994-01-01

Our studies focus on the stratigraphy of Late Devonian to early Pennsylvanian rocks at the NTS, because these are the best potential hydrocarbon source rocks in the vicinity of Yucca Mountain. In the last year, our stratigraphic studies have broadened to include the regional context for both the Chainman and the Eleana formations. New age data based on biostratigraphy constrain the age ranges of both Chainman and Eleana; accurate and reliable ages are essential for regional correlation and for regional paleogeographic reconstructions. Source rock analyses throughout the Chainman establish whether these rocks contained adequate organic material to generate hydrocarbons. Maturation analyses of samples from the Chainman determine whether the temperature history has been suitable for the generation of liquid hydrocarbons. Structural studies are aimed at defining the deformation histories and present position of the different packages of Devonian - Pennsylvanian rocks. This report summarizes new results of our structural, stratigraphic and hydrocarbon source rock potential studies at the Nevada Test Site and vicinity. Stratigraphy is considered first, with the Chainman Shale and Eleana Formation discussed separately. New biostratigraphic results are included in this section. New results from our structural studies are summarized next, followed by source rock and maturation analyses of the Chainman Shale. Directions for future work are included where appropriate

Hydrocarbon potential of a new Jurassic play, central Tunisia

International Nuclear Information System (INIS)

Beall, A.O.; Law, C.W.

1996-01-01

A largely unrecognized Jurassic Sag Basin has been identified in central Tunisia, proximal to the Permo-Carboniferous flexure delineating the northern boundary of the Saharan platform of north Africa. The northwestern margin of the Sag is delineated by an extensive region of salt-cored anticlines and localized salt diapirs extending north and west. Due to lack of deep drilling, delineation of the Sag is largely based on regional gravity data. Subsidence of the Jurassic Sag Basin is characterized by rapid expansion of Jurassic sediments from 400 m. of tidal flat and shelf carbonate at the western outcrop to over 2000 meters of tidal flat and basinal carbonate and shale within the basin center, a five-fold expansion. Rapid loading of the basin continued into Lower Cretaceous time, marked by lateral flowage of Triassic salt into pronounced structural trends. Published source rock data and interpreted subsurface well data provided the basis for GENEX 1-D hydrocarbon generation and expulsion modeling of the Sag. Middle Jurassic black source shales typically contain Type II and Type III kerogens with T.O.C.'s ranging up to 4 percent. Modeling results indicate that middle Jurassic shales are presently mature for liquid generation within portions of the Sag, with maximum generation taking place during the Tertiary. Potential hydrocarbon generation yields, based on 60 meters of mature source shale, are 20,000 BOE/acre for gas and 75,000 BOE/acre for liquids. Prospects within the region could contain an estimated potential reserve of several T.C.F. or over 1 billion barrels of oil

Method for the conversion of hydrocarbon charges

Energy Technology Data Exchange (ETDEWEB)

Whittam, T V

1976-11-11

The basis of the invention is the application of defined zeolites as catalysts to hydrocarbon conversion processes such as reformation, isomerization, dehydrocyclization, and cracking. By charging the zeolite carrier masses with 0.001 to 5% metal of the 8th group of the periodic system, preferably noble metals, a wide region of applications for the catalysts is achieved. A method for the isomerization of an alkyl benzene (or mixture of alkyl benzenes) in the liquid or gas phase under suitable temperature, pressure and flow-rate conditions, as well as in the presence of a cyclic hydrocarbon, is described as preferential model form of the invention; furthermore, a method for the reformation of a hydrocarbon fraction boiling in the gasoline or benzene boiling region and a method for the hydrocracking of hydrocarbon charge (e.g. naphtha, kerosine, gas oils) are given. Types of performance of the methods are explained using various examples.

Prediction of Hydrocarbon Reservoirs Permeability Using Support Vector Machine

Directory of Open Access Journals (Sweden)

R. Gholami

2012-01-01

Full Text Available Permeability is a key parameter associated with the characterization of any hydrocarbon reservoir. In fact, it is not possible to have accurate solutions to many petroleum engineering problems without having accurate permeability value. The conventional methods for permeability determination are core analysis and well test techniques. These methods are very expensive and time consuming. Therefore, attempts have usually been carried out to use artificial neural network for identification of the relationship between the well log data and core permeability. In this way, recent works on artificial intelligence techniques have led to introduce a robust machine learning methodology called support vector machine. This paper aims to utilize the SVM for predicting the permeability of three gas wells in the Southern Pars field. Obtained results of SVM showed that the correlation coefficient between core and predicted permeability is 0.97 for testing dataset. Comparing the result of SVM with that of a general regression neural network (GRNN revealed that the SVM approach is faster and more accurate than the GRNN in prediction of hydrocarbon reservoirs permeability.

The role of fluid migration system in hydrocarbon accumulation in Maichen Sag, Beibuwan Basin

Science.gov (United States)

Liu, Hongyu; Yang, Jinxiu; Wu, Feng; Chen, Wei; Liu, Qianqian

2018-02-01

Fluid migration system is of great significance for hydrocarbon accumulation, including the primary migration and secondary migration. In this paper, the fluid migration system is analysed in Maichen Sag using seismic, well logging and core data. Results show that many factors control the hydrocarbon migration process, including hydrocarbon generation and expulsion period from source rocks, microfractures developed in the source rocks, the connected permeable sand bodies, the vertical faults cutting into/through the source rocks and related fault activity period. The spatial and temporal combination of these factors formed an effective network for hydrocarbon expulsion and accumulation, leading to the hydrocarbon reservoir distribution at present. Generally, a better understanding of the hydrocarbon migration system can explain the present status of hydrocarbon distribution, and help select future target zones for oil and gas exploration.

Ambient aromatic hydrocarbon measurements at Welgegund, South Africa

Science.gov (United States)

Jaars, K.; Beukes, J. P.; van Zyl, P. G.; Venter, A. D.; Josipovic, M.; Pienaar, J. J.; Vakkari, V.; Aaltonen, H.; Laakso, H.; Kulmala, M.; Tiitta, P.; Guenther, A.; Hellén, H.; Laakso, L.; Hakola, H.

2014-07-01

Aromatic hydrocarbons are associated with direct adverse human health effects and can have negative impacts on ecosystems due to their toxicity, as well as indirect negative effects through the formation of tropospheric ozone and secondary organic aerosol, which affect human health, crop production and regional climate. Measurements of aromatic hydrocarbons were conducted at the Welgegund measurement station (South Africa), which is considered to be a regionally representative background site. However, the site is occasionally impacted by plumes from major anthropogenic source regions in the interior of South Africa, which include the western Bushveld Igneous Complex (e.g. platinum, base metal and ferrochrome smelters), the eastern Bushveld Igneous Complex (platinum and ferrochrome smelters), the Johannesburg-Pretoria metropolitan conurbation (> 10 million people), the Vaal Triangle (e.g. petrochemical and pyrometallurgical industries), the Mpumalanga Highveld (e.g. coal-fired power plants and petrochemical industry) and also a region of anticyclonic recirculation of air mass over the interior of South Africa. The aromatic hydrocarbon measurements were conducted with an automated sampler on Tenax-TA and Carbopack-B adsorbent tubes with heated inlet for 1 year. Samples were collected twice a week for 2 h during daytime and 2 h during night-time. A thermal desorption unit, connected to a gas chromatograph and a mass selective detector was used for sample preparation and analysis. Results indicated that the monthly median (mean) total aromatic hydrocarbon concentrations ranged between 0.01 (0.011) and 3.1 (3.2) ppb. Benzene levels did not exceed the local air quality standard limit, i.e. annual mean of 1.6 ppb. Toluene was the most abundant compound, with an annual median (mean) concentration of 0.63 (0.89) ppb. No statistically significant differences in the concentrations measured during daytime and night-time were found, and no distinct seasonal patterns were

OUTFLOWS AND DARK BANDS AT ARCADE-LIKE ACTIVE REGION CORE BOUNDARIES

Energy Technology Data Exchange (ETDEWEB)

Scott, J. T.; Martens, P. C. H.; Tarr, L. [Department of Physics, Montana State University, Bozeman, MT 59717 (United States)

2013-03-10

Observations from the EUV Imaging Spectrometer (EIS) on board Hinode have revealed outflows and non-thermal line broadening in low intensity regions at the edges of active regions (ARs). We use data from Hinode's EIS, Solar Dynamic Observatory's Atmospheric Imaging Assembly and Helioseismic and Magnetic Imager, and the Transition Region and Coronal Explorer instrument to investigate the boundaries of arcade-like AR cores for NOAA ARs 11112, 10978, and 9077. A narrow, low intensity region that is observed at the core's periphery as a dark band shows outflows and increased spectral line broadening. This dark band is found to exist for days and appears between the bright coronal loop structures of different coronal topologies. We find a case where the dark band region is formed between the magnetic field from emerging flux and the field of the pre-existing flux. A magnetic field extrapolation indicates that this dark band is coincident with the spine lines or magnetic separatrices in the extrapolated field. This occurs over unipolar regions where the brightened coronal field is separated in connectivity and topology. This separation does not appear to be infinitesimal and an initial estimate of the minimum distance of separation is found to be Almost-Equal-To 1.5-3.5 Mm.

Ambient aromatic hydrocarbon measurements at Welgegund, South Africa

Energy Technology Data Exchange (ETDEWEB)

Jaars, K.; Beukes, J. P.; van Zyl, P. G.; Venter, A. D.; Josipovic, M.; Pienaar, J. J.; Vakkari, Ville; Aaltonen, H.; Laakso, H.; Kulmala, M.; Tiitta, P.; Guenther, Alex B.; Hellen, H.; Laakso, L.; Hakola, H.

2014-07-11

Aromatic hydrocarbons are associated with direct adverse human health effects and can have negative impacts on ecosystems due to their toxicity, as well as indirect negative effects through the formation of tropospheric ozone and secondary organic aerosol that affect human health, crop production and regional climate. Measurements were conducted at the Welgegund measurement station (South Africa) that is considered to be a regionally representative background site. However, the site is occasionally impacted by plumes from major anthropogenic source regions in the interior of South Africa, which include the western Bushveld Igneous Complex (e.g. platinum, base metal and ferrochrome smelters), the eastern Bushveld Igneous Complex (platinum and ferrochrome smelters), the Johannesburg-Pretoria metropolitan conurbation (>10 million people), the Vaal Triangle (e.g. petrochemical and industries), the Mpumalanga Highveld (e.g. coal-fired power plants and petrochemical industry) and also a region of anti-cyclonic recirculation of air mass over the interior of South Africa. The aromatic hydrocarbon measurements were conducted with an automated sampler on Tenax-TA and Carbopack-B adsorbent tubes with heated inlet for one year. Samples were collected twice a week for two hours during daytime and two hours 1 during night-time. A thermal desorption unit, connected to a gas chromatograph and a mass 2 selective detector was used for sample preparation and analysis. Results indicated that the 3 monthly median total aromatic hydrocarbon concentrations ranged between 0.01 to 3.1 ppb. 4 Benzene levels did not exceed local air quality standards. Toluene was the most abundant 5 species, with an annual median concentration of 0.63 ppb. No statistically significant 6 differences in the concentrations measured during daytime and night-time were found and no distinct seasonal patterns were observed. Air mass back trajectory analysis proved that the lack of seasonal cycles could be

Role of wall-attached structures in the interface of the quiescent core region in turbulent pipe flow

Science.gov (United States)

Yang, Jongmin; Hwang, Jinyul; Sung, Hyung Jin

2017-11-01

The effects of low- and high-speed structures on the interface of the quiescent core region are explored using direct numerical simulation data of turbulent pipe flow. The quiescent core region is a uniform momentum zone located at the center of the pipe flow, which contains the highest streamwise momentum with a low level of turbulence. The interface of the quiescent core region can be identified from the probability density function of the streamwise modal velocity. In the vicinity of the interface of the quiescent core region, the streamwise velocity changes abruptly. The abrupt jump in velocity causes an increase of the velocity gradient. The interface of the quiescent core region is similar to the laminar superlayer in turbulent/non-turbulent interface. The interface of the quiescent core region contains the low- and high-speed structures. They can be classified into wall-attached and detached structures depending on the distance between the structures and the wall. The influence of the detached structures accounted for most of the number of detected structures is negligible due to its small volume. Conversely, the wall-attached structures adjacent to the interface have a huge influence on the statistical amount of the interface, such as entrainment characteristics. This work was supported by the Creative Research Initiatives (No. 2017-013369) program of the National Research Foundation of Korea (MSIP).

Studies on hydrocarbon degradation by the bacterial isolate ...

African Journals Online (AJOL)

The hydrocarbon utilizing capability of Stenotrophomonas rhizophila (PM-1), isolated from oil contaminated soil composts from Western Ghats region of Karnataka was analyzed. In the bioremediation experiment, ONGC heavy crude oil and poly aromatic hydrocarbons (PAHs) utilization by the bacterial isolate was studied.

Cytotoxic T lymphocytes and CD4 epitope mutations in the pre-core/core region of hepatitis B virus in chronic hepatitis B carriers in Northeast Iran.

Science.gov (United States)

Zhand, Sareh; Tabarraei, Alijan; Nazari, Amineh; Moradi, Abdolvahab

2017-07-01

Hepatitis B virus (HBV) is vulnerable to many various mutations. Those within epitopes recognized by sensitized T cells may influence the re-emergence of the virus. This study was designed to investigate the mutation in immune epitope regions of HBV pre-core/core among chronic HBV patients of Golestan province, Northeast Iran. In 120 chronic HBV carriers, HBV DNA was extracted from blood plasma samples and PCR was done using specific primers. Direct sequencing and alignment of the pre-core/core region were applied using reference sequence from Gene Bank database (Accession Number AB033559). The study showed 27 inferred amino acid substitutions, 9 of which (33.3%) were in CD4 and 2 (7.4%) in cytotoxic T lymphocytes' (CTL) epitopes and 16 other mutations (59.2%) were observed in other regions. CTL escape mutations were not commonly observed in pre-core/core sequences of chronic HBV carriers in the locale of study. It can be concluded that most of the inferred amino acid substitutions occur in different immune epitopes other than CTL and CD4.

Bio-remediation of hydrocarbons in coastal regions; Bioremediation des hydrocarbures en milieu cotier

Energy Technology Data Exchange (ETDEWEB)

Guyoneaud, R. [IBEAS, LEM - Lab. d' Ecologie Moleculaire - JE 159, 64 - Pau (France)

2001-07-01

Coasts are exposed to chronic or accidental pollutions by hydrocarbons. The aim of this study is to show the importance of the microbial layers (stratified sedimentary systems) in the biodegradation of the hydrocarbons. (A.L.B.)

Regional overpower protection system analysis for a DUPIC fuel CANDU core

International Nuclear Information System (INIS)

Jeong, Chang Joon; Choi, Hang Bok; Park, Jee Won

2003-06-01

The regional overpower protection (ROP) system was assessed a CANDU 6 reactor with the DUPIC fuel, including the validation of the WIMS/RFSP/ROVER-F code system used for the estimation of ROP trip setpoint. The validation calculation has shown that it is valid to use the WIMS/RFSP/ROVER-F code system for ROP system analysis of the CANDU 6 core. For the DUPIC core, the ROP trip setpoint was estimated to be 125.7%, which is almost the same as that of the standard natural uranium core. This study has shown that the DUPIC fuel does not hurt the current ROP trip setpoint designed for the natural uranium CANDU 6 reactor

From upstream to downstream: Megatrends and latest developments in Latin America`s hydrocarbons sector

Energy Technology Data Exchange (ETDEWEB)

Wu, Kang; Pezeshki, S.; McMahon, J.

1995-08-01

In recent years, Latin America`s hydrocarbons sector has been characterized by reorganization, revitalization, regional cooperation, environmental awakening, and steady expansion. The pattern of these changes, which appear to be the megatrends of the region`s hydrocarbons sector development, will continue during the rest of the 1990s. To further study the current situation and future prospects of Latin America`s hydrocarbons sector, we critically summarize in this short article the key issues in the region`s oil and gas development. These megatrends in Latin America`s hydrocarbons sector development will impact not only the future energy demand and supply in the region, but also global oil flows in the North American market and across the Pacific Ocean. Each country is individually discussed; pipelines to be constructed are discussed also.

Natural selection in a population of Drosophila melanogaster explained by changes in gene expression caused by sequence variation in core promoter regions.

Science.gov (United States)

Sato, Mitsuhiko P; Makino, Takashi; Kawata, Masakado

2016-02-09

Understanding the evolutionary forces that influence variation in gene regulatory regions in natural populations is an important challenge for evolutionary biology because natural selection for such variations could promote adaptive phenotypic evolution. Recently, whole-genome sequence analyses have identified regulatory regions subject to natural selection. However, these studies could not identify the relationship between sequence variation in the detected regions and change in gene expression levels. We analyzed sequence variations in core promoter regions, which are critical regions for gene regulation in higher eukaryotes, in a natural population of Drosophila melanogaster, and identified core promoter sequence variations associated with differences in gene expression levels subjected to natural selection. Among the core promoter regions whose sequence variation could change transcription factor binding sites and explain differences in expression levels, three core promoter regions were detected as candidates associated with purifying selection or selective sweep and seven as candidates associated with balancing selection, excluding the possibility of linkage between these regions and core promoter regions. CHKov1, which confers resistance to the sigma virus and related insecticides, was identified as core promoter regions that has been subject to selective sweep, although it could not be denied that selection for variation in core promoter regions was due to linked single nucleotide polymorphisms in the regulatory region outside core promoter regions. Nucleotide changes in core promoter regions of CHKov1 caused the loss of two basal transcription factor binding sites and acquisition of one transcription factor binding site, resulting in decreased gene expression levels. Of nine core promoter regions regions associated with balancing selection, brat, and CG9044 are associated with neuromuscular junction development, and Nmda1 are associated with learning

A Study of THT Cold Cores Population in the Star-Forming Region in Serpens

Science.gov (United States)

Fiorellino, Eleonora

2017-11-01

The purpose of this work is to produce the Core Mass Function (CMF) of the Serpens star-forming region and confront it with the Initial Mass Function (IMF), the statistical distribution of initial star mass. As Testi & Sergent (1998) discovered, the power-law index of the slope of the CMF is very close to the one of the Salpeter's IMF (Salpeter, 1955): dN/dM / M2.35. This strongly suggests that the stellar IMF results from the fragmentation process in turbulent cloud cores rather than from stellar accretion mechanisms and gives a huge contribute to undestanding the star formation. For this work, we started from the data delivered by the European satellite Herschel and produced the maps of the Serpens with Unimap code (Piazzo et al, 2015). Hence we obtained a core catalogue with two different softwares getsources (Men'shchikov et al, 2012) and CuTEx (Molinari et al, 2011) and we eliminated from it any source that is not a core. A full discussion of the cores physical propreties as well as the whole region is under preparation.

Oil spill aftermath : temporal evaluation of hydrocarbon sources in Guanabara Bay, Brazil

International Nuclear Information System (INIS)

Meniconi, M.F.G.; Massone, C.G.; Scofield, A.L.; Junior, V.J.F.

2005-01-01

The sources of polycyclic aromatic hydrocarbons (PAH) in environmental ecosystems are both natural and anthropogenic. PAHs interact with different types of environmental compartments and are subject to processes that lead to geochemical fates such as physical-chemical transformation, biodegradation and photo-oxidation. This study examined the sources of PAHs in the estuarine sediment of Guanabara Bay, Brazil following an accidental oil spill from an oil refinery in January 2000. The main portion of the oil was carried by tidal currents and wind. It spread over the water and reached islands and shorelines at the north part of the bay. The objective of this study was to determine the likely sources of hydrocarbons in the bay where untreated municipal sewage and industrial wastes are also dumped. Sediment samples were collected using cores and dredges from the intertidal and subtidal regions of the bay, reflecting both affected and unaffected areas. This paper summarized the results of 16 EPA priority PAH and their alkylated homologues from 21 sediment samples collected in the bay 10 days after the oil spill, immediately after the clean up effort, and then 3 years later. The hydrocarbon source was determined using PAH ratios for the samples studied. The highest PAH concentration was observed in 2000 as a result of the petrogenic and pyrolytic contribution to the sediments. 38 refs., 3 tabs., 9 figs

A case study of the intrinsic bioremediation of petroleum hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Barker, G.W.; Raterman, K.T.; Fisher, J.B.; Corgan, J.M. [and others

1995-12-31

Condensate liquids have been found to contaminate soil and groundwater at two gas production sites in the Denver Basin operated by Amoco Production Co. These sites have been closely monitored since July 1993 to determine whether intrinsic aerobic or anaerobic bioremediation of hydrocarbons occurs at a sufficient rate and to an adequate endpoint to support a no-intervention decision. Groundwater monitoring and analysis of soil cores suggest that intrinsic bioremediation is occurring at these sites by multiple pathways including aerobic oxidation, Fe{sup 3+} reduction, and sulfate reduction. In laboratory experiments the addition of gas condensate hydrocarbons to saturated soil from the gas production site stimulated sulfate reduction under anaerobic and oxygen-limiting conditions, and nitrate and Fe{sup 3+} reduction under oxygen-limiting conditions, compared to biotic controls that lacked hydrocarbon and sterile controls. The sulfate reduction corresponded to a reduction in the amount of toluene relative to other hydrocarbons. These results confirmed that subsurface soils at the gas production site have the potential for intrinsic bioremediation of hydrocarbons.

Spectrometric gamma radiation of shale cores applied to sweet spot discrimination in Eastern Pomerania, Poland

Science.gov (United States)

Skupio, Rafal; de Alemar Barberes, Gabriel

2017-12-01

This paper describes the application and calculation of hydrocarbon anomalies in two different boreholes located in Eastern Pomerania (northern Poland). Spectrometric data from borehole geophysical probe (borehole 1) and portable gamma logger (borehole 2) were used to analyze shale formations. The results from borehole 1 presented a statistically significant, moderate correlation between calculated hydrocarbon anomalies and hydrocarbon saturation data obtained from well log interpretation. Borehole 2 has been analyzed focusing on the gamma radiation of the core samples, and the positive results of borehole 1. Hydrocarbon anomalies calculated from spectral gamma radiation are reliable indicators of sweet spots, based solely on a cursory evaluation of core measurements. These preliminary information acquired from gamma-ray measurements could help increase sampling precision of further geochemical analysis.

Structure of the protein core of the glypican Dally-like and localization of a region important for hedgehog signaling

Energy Technology Data Exchange (ETDEWEB)

Kim, Min-Sung; Saunders, Adam M.; Hamaoka, Brent Y.; Beachy, Philip A.; Leahy, Daniel J. (Stanford-MED); (JHU)

2011-09-20

Glypicans are heparan sulfate proteoglycans that modulate the signaling of multiple growth factors active during animal development, and loss of glypican function is associated with widespread developmental abnormalities. Glypicans consist of a conserved, approximately 45-kDa N-terminal protein core region followed by a stalk region that is tethered to the cell membrane by a glycosyl-phosphatidylinositol anchor. The stalk regions are predicted to be random coil but contain a variable number of attachment sites for heparan sulfate chains. Both the N-terminal protein core and the heparan sulfate attachments are important for glypican function. We report here the 2.4-{angstrom} crystal structure of the N-terminal protein core region of the Drosophila glypican Dally-like (Dlp). This structure reveals an elongated, {alpha}-helical fold for glypican core regions that does not appear homologous to any known structure. The Dlp core protein is required for normal responsiveness to Hedgehog (Hh) signals, and we identify a localized region on the Dlp surface important for mediating its function in Hh signaling. Purified Dlp protein core does not, however, interact appreciably with either Hh or an Hh:Ihog complex.

Improvement of Core Performance by Introduction of Moderators in a Blanket Region of Fast Reactors

Directory of Open Access Journals (Sweden)

Toshio Wakabayashi

2013-01-01

Full Text Available An application of deuteride moderator for fast reactor cores is proposed for power flattening that can mitigate thermal spikes and alleviate the decrease in breeding ratio, which sometimes occurs when hydrogen moderator is applied as a moderator. Zirconium deuteride is employed in a form of pin arrays at the inner most rows of radial blanket fuel assemblies, which works as a reflector in order to flatten the radial power distribution in the outer core region of MONJU. The power flattening can be utilized to increase core average burn-up by increasing operational time. The core characteristics have been evaluated with a continuous-energy model Monte Carlo code MVP and the JENDL-3.3 cross-section library. The result indicates that the discharged fuel burn-up can be increased by about 7% relative to that of no moderator in the blanket region due to the power flattening when the number of deuteride moderator pins is 61. The core characteristics and core safety such as void reactivity, Doppler coefficient, and reactivity insertion that occurred at dissolution of deuteron were evaluated. It was clear that the serious drawback did not appear from the viewpoints of the core characteristics and core safety.

An interpretation of core and wireline logs for the Petrophysical evaluation of Upper Shallow Marine sandstone reservoirs of the Bredasdorp Basin, offshore South Africa

Science.gov (United States)

Magoba, Moses; Opuwari, Mimonitu

2017-04-01

This paper embodies a study carried out to assess the Petrophysical evaluation of upper shallow marine sandstone reservoir of 10 selected wells in the Bredasdorp basin, offshore, South Africa. The studied wells were selected randomly across the upper shallow marine formation with the purpose of conducting a regional study to assess the difference in reservoir properties across the formation. The data sets used in this study were geophysical wireline logs, Conventional core analysis and geological well completion report. The physical rock properties, for example, lithology, fluid type, and hydrocarbon bearing zone were qualitatively characterized while different parameters such as volume of clay, porosity, permeability, water saturation ,hydrocarbon saturation, storage and flow capacity were quantitatively estimated. The quantitative results were calibrated with the core data. The upper shallow marine reservoirs were penetrated at different depth ranging from shallow depth of about 2442m to 3715m. The average volume of clay, average effective porosity, average water saturation, hydrocarbon saturation and permeability range from 8.6%- 43%, 9%- 16%, 12%- 68% , 32%- 87.8% and 0.093mD -151.8mD respectively. The estimated rock properties indicate a good reservoir quality. Storage and flow capacity results presented a fair to good distribution of hydrocarbon flow.

High permeability cores to optimize the stimulation of deeply located brain regions using transcranial magnetic stimulation

International Nuclear Information System (INIS)

Salvador, R; Miranda, P C; Roth, Y; Zangen, A

2009-01-01

Efficient stimulation of deeply located brain regions with transcranial magnetic stimulation (TMS) poses many challenges, arising from the fact that the induced field decays rapidly and becomes less focal with depth. We propose a new method to improve the efficiency of TMS of deep brain regions that combines high permeability cores, to increase focality and field intensity, with a coil specifically designed to induce a field that decays slowly with increasing depth. The performance of the proposed design was investigated using the finite element method to determine the total electric field induced by this coil/core arrangement on a realistically shaped homogeneous head model. The calculations show that the inclusion of the cores increases the field's magnitude by as much as 25% while also decreasing the field's decay with depth along specific directions. The focality, as measured by the area where the field's norm is greater than 1/√2 of its maximum value, is also improved by as much as 15% with some core arrangements. The coil's inductance is not significantly increased by the cores. These results show that the presence of the cores might make this specially designed coil even more suited for the effective stimulation of deep brain regions.

High permeability cores to optimize the stimulation of deeply located brain regions using transcranial magnetic stimulation

Science.gov (United States)

Salvador, R.; Miranda, P. C.; Roth, Y.; Zangen, A.

2009-05-01

Efficient stimulation of deeply located brain regions with transcranial magnetic stimulation (TMS) poses many challenges, arising from the fact that the induced field decays rapidly and becomes less focal with depth. We propose a new method to improve the efficiency of TMS of deep brain regions that combines high permeability cores, to increase focality and field intensity, with a coil specifically designed to induce a field that decays slowly with increasing depth. The performance of the proposed design was investigated using the finite element method to determine the total electric field induced by this coil/core arrangement on a realistically shaped homogeneous head model. The calculations show that the inclusion of the cores increases the field's magnitude by as much as 25% while also decreasing the field's decay with depth along specific directions. The focality, as measured by the area where the field's norm is greater than 1/\\sqrt 2 of its maximum value, is also improved by as much as 15% with some core arrangements. The coil's inductance is not significantly increased by the cores. These results show that the presence of the cores might make this specially designed coil even more suited for the effective stimulation of deep brain regions.

High permeability cores to optimize the stimulation of deeply located brain regions using transcranial magnetic stimulation

Energy Technology Data Exchange (ETDEWEB)

Salvador, R; Miranda, P C [Institute of Biophysics and Biomedical Engineering, Faculty of Sciences, University of Lisbon, 1749-016 Lisbon (Portugal); Roth, Y [Advanced Technology Center, Sheba Medical Center, Tel-Hashomer (Israel); Zangen, A [Neurobiology Department, Weizmann Institute of Science, Rehovot 76100 (Israel)], E-mail: rnsalvador@fc.ul.pt

2009-05-21

Efficient stimulation of deeply located brain regions with transcranial magnetic stimulation (TMS) poses many challenges, arising from the fact that the induced field decays rapidly and becomes less focal with depth. We propose a new method to improve the efficiency of TMS of deep brain regions that combines high permeability cores, to increase focality and field intensity, with a coil specifically designed to induce a field that decays slowly with increasing depth. The performance of the proposed design was investigated using the finite element method to determine the total electric field induced by this coil/core arrangement on a realistically shaped homogeneous head model. The calculations show that the inclusion of the cores increases the field's magnitude by as much as 25% while also decreasing the field's decay with depth along specific directions. The focality, as measured by the area where the field's norm is greater than 1/{radical}2 of its maximum value, is also improved by as much as 15% with some core arrangements. The coil's inductance is not significantly increased by the cores. These results show that the presence of the cores might make this specially designed coil even more suited for the effective stimulation of deep brain regions.

Estimation of sources and inflow of dioxins and polycyclic aromatic hydrocarbons from the sediment core of Lake Suwa, Japan

International Nuclear Information System (INIS)

Ikenaka, Yoshinori; Eun, Heesoo; Watanabe, Eiki; Kumon, Fujio; Miyabara, Yuichi

2005-01-01

To elucidate the historical changes in polychlorinated dibenzo-p-dioxin (PCDD), polychlorinated dibenzofuran (PCDF), coplanar polychlorinated biphenyl (co-PCB), and polycyclic aromatic hydrocarbon (PAH) inflows in Lake Suwa, their concentrations in the sediment core were analyzed in 5 cm interval. The maximum concentrations (depth cm) of PCDDs/DFs, co-PCBs, and PAHs were 25.2 ng/g dry (30-35 cm), 19.0 ng/g dry (30-35 cm), and 738, 795 ng/g dry (50-55 cm, 30-35 cm), respectively. Age and sedimentation rate of the sediment were estimated from the vertical changes in apparent density. Deposition rate of dioxins and PAHs were calculated from the concentration and sedimentation rate of the sediment. The results indicate that large amounts of dioxins and PAHs flowed into the lake in flood stage compared to normal stage. - Large amounts of dioxins and PAHs flowed into a lake in flood events

Application of fission track analysis to hydrocarbon exploration

International Nuclear Information System (INIS)

Duddy, I.R.; Green, P.F.; Gleadow, A.J.W.; Marshallsea, S.; Tingate, P.; Laslett, G.M.; Hegarty, K.A.; Lovering, J.F.

1985-01-01

The temperature range over which fission tracks in apatite show observable annealing effects coincides with that responsible for the maximum generation of liquid hydrocarbons. Work is currently in progress in a number of Australian and overseas sedimentary basins, applying Apatite Fission Track Analysis (AFTA) to investigate the thermal evolution of these hydrocarbon prospective regions

Measurement and analysis of reaction rate distributions of cores with spectrum shifter region

International Nuclear Information System (INIS)

Matsuura, Shigekazu; Shiroya, Seiji; Unesaki, Hironobu; Takeda, Toshikazu; Aizawa, Otohiko; Kanda, Keiji.

1995-01-01

A study for the neutronic characteristics of the spectrum-controlled neutron irradiation fields using various reflector materials was performed. Spectrum shifter regions were constructed in the upper reflector region of the solid moderated core (B-Core) of the Kyoto University Critical Assembly (KUCA). Beryllium, graphite and aluminum were selected as the loading materials for the spectrum shifter. Two tight-pitch lattice cores with different moderator-to-fuel volume ratio (V m /V f ) of 0.97 and 0.65 have been used. Axial reaction rate distributions of gold, nickel and indium wires were measured, and the spectrum index was defined as the Cd ratio of the gold wire and the ratio of gold reaction rate to nickel reaction rate. Using the conventional design calculation procedure, the experimental and calculated reaction rate and spectrum index show several disagreements. Detailed treatment of the neutron streaming effect, heterogeneous cell structure and depression factor are shown to be necessary for improving the agreement between experimental and calculated values. (author)

Subduction zone earthquake probably triggered submarine hydrocarbon seepage offshore Pakistan

Science.gov (United States)

Fischer, David; José M., Mogollón; Michael, Strasser; Thomas, Pape; Gerhard, Bohrmann; Noemi, Fekete; Volkhard, Spiess; Sabine, Kasten

2014-05-01

Seepage of methane-dominated hydrocarbons is heterogeneous in space and time, and trigger mechanisms of episodic seep events are not well constrained. It is generally found that free hydrocarbon gas entering the local gas hydrate stability field in marine sediments is sequestered in gas hydrates. In this manner, gas hydrates can act as a buffer for carbon transport from the sediment into the ocean. However, the efficiency of gas hydrate-bearing sediments for retaining hydrocarbons may be corrupted: Hypothesized mechanisms include critical gas/fluid pressures beneath gas hydrate-bearing sediments, implying that these are susceptible to mechanical failure and subsequent gas release. Although gas hydrates often occur in seismically active regions, e.g., subduction zones, the role of earthquakes as potential triggers of hydrocarbon transport through gas hydrate-bearing sediments has hardly been explored. Based on a recent publication (Fischer et al., 2013), we present geochemical and transport/reaction-modelling data suggesting a substantial increase in upward gas flux and hydrocarbon emission into the water column following a major earthquake that occurred near the study sites in 1945. Calculating the formation time of authigenic barite enrichments identified in two sediment cores obtained from an anticlinal structure called "Nascent Ridge", we find they formed 38-91 years before sampling, which corresponds well to the time elapsed since the earthquake (62 years). Furthermore, applying a numerical model, we show that the local sulfate/methane transition zone shifted upward by several meters due to the increased methane flux and simulated sulfate profiles very closely match measured ones in a comparable time frame of 50-70 years. We thus propose a causal relation between the earthquake and the amplified gas flux and present reflection seismic data supporting our hypothesis that co-seismic ground shaking induced mechanical fracturing of gas hydrate-bearing sediments

Opportunities for development of non-traditional hydrocarbon resources in the Timan-North Ural region, taking into account ecosystem services

Directory of Open Access Journals (Sweden)

I. G. Burtseva

2017-12-01

Full Text Available The authors formulate the definition of non-traditional resources from geological-genetic, technological and economic viewpoints. The authors present a detailed assessment of the resource potential of non-traditional hydrocarbon raw material in the Timan-Severouralsk region, including hydrocarbons in the deposits of the domanic type, methane of coal seams, liquid and gaseous hydrocarbons potentially extracted from black, brown coal and combustible shales. The authors also show the main directions of industrial use of coal and oil shales. The assessment of the resource potential of hydrocarbon raw materials in the deposits of the domanic type varies widely; the recoverable resources may amount to about 1 billion tons. Bituminous coals with a high volatile yield have the highest degree of conversion to liquid hydrocarbons, and brown and black coals of with a low degree of metamorphism usually serve for the production of combustible gas and primary resin. The paper describes the option of developing oil shale deposits as a possible investment project. The determined components and overall values of the economic effect from the implementation of the projects under consideration allow us to estimate that the payback period of investments does not exceed seven years. There is also a social effect: the creation of an additional 550 jobs in the operation of the quarry and about 700 jobs – in the enrichment and processing of oil shales. The estimated annual volume of output is 25–30 billion rubles, and the volume of tax revenues – up to 100 billion rubles. The authors evaluated ecosystem services in the territories of potential industrial development of coal and oil shale deposits; identified the beneficiaries of the benefits from the use of environmental services and the possibility of calculating payments.

THE STRUCTURE, ORIGIN, AND EVOLUTION OF INTERSTELLAR HYDROCARBON GRAINS

Energy Technology Data Exchange (ETDEWEB)

Chiar, J. E.; Ricca, A. [SETI Institute, Carl Sagan Center, 189 Bernardo Avenue, Mountain View, CA 94043 (United States); Tielens, A. G. G. M. [Leiden Observatory, P.O. Box 9513, NL-2300 RA Leiden (Netherlands); Adamson, A. J., E-mail: jchiar@seti.org, E-mail: Alessandra.Ricca@1.nasa.gov, E-mail: tielens@strw.leidenuniv.nl, E-mail: aadamson@gemini.edu [Gemini Observatory, Northern Operations Center, 670 North A' ohoku Place, Hilo, HI 96729 (United States)

2013-06-10

Many materials have been considered for the carrier of the hydrocarbon absorption bands observed in the diffuse interstellar medium (ISM). In order to refine the model for ISM hydrocarbon grains, we analyze the observed aromatic (3.28, 6.2 {mu}m) and aliphatic (3.4 {mu}m) hydrocarbon absorption features in the diffuse ISM along the line of sight toward the Galactic center Quintuplet Cluster. Observationally, sp {sup 2} bonds can be measured in astronomical spectra using the 6.2 {mu}m CC aromatic stretch feature, whereas the 3.4 {mu}m aliphatic feature can be used to quantify the fraction of sp {sup 3} bonds. The fractional abundance of these components allows us to place the Galactic diffuse ISM hydrocarbons on a ternary phase diagram. We conclude that the Galactic hydrocarbon dust has, on average, a low H/C ratio and sp {sup 3} content and is highly aromatic. We have placed the results of our analysis within the context of the evolution of carbon dust in the ISM. We argue that interstellar carbon dust consists of a large core of aromatic carbon surrounded by a thin mantle of hydrogenated amorphous carbon (a-C:H), a structure that is a natural consequence of the processing of stardust grains in the ISM.

THE STRUCTURE, ORIGIN, AND EVOLUTION OF INTERSTELLAR HYDROCARBON GRAINS

International Nuclear Information System (INIS)

Chiar, J. E.; Ricca, A.; Tielens, A. G. G. M.; Adamson, A. J.

2013-01-01

Many materials have been considered for the carrier of the hydrocarbon absorption bands observed in the diffuse interstellar medium (ISM). In order to refine the model for ISM hydrocarbon grains, we analyze the observed aromatic (3.28, 6.2 μm) and aliphatic (3.4 μm) hydrocarbon absorption features in the diffuse ISM along the line of sight toward the Galactic center Quintuplet Cluster. Observationally, sp 2 bonds can be measured in astronomical spectra using the 6.2 μm CC aromatic stretch feature, whereas the 3.4 μm aliphatic feature can be used to quantify the fraction of sp 3 bonds. The fractional abundance of these components allows us to place the Galactic diffuse ISM hydrocarbons on a ternary phase diagram. We conclude that the Galactic hydrocarbon dust has, on average, a low H/C ratio and sp 3 content and is highly aromatic. We have placed the results of our analysis within the context of the evolution of carbon dust in the ISM. We argue that interstellar carbon dust consists of a large core of aromatic carbon surrounded by a thin mantle of hydrogenated amorphous carbon (a-C:H), a structure that is a natural consequence of the processing of stardust grains in the ISM.

Microbial activity in an acid resin deposit: Biodegradation potential and ecotoxicology in an extremely acidic hydrocarbon contamination

International Nuclear Information System (INIS)

Kloos, Karin; Schloter, Michael; Meyer, Ortwin

2006-01-01

Acid resins are residues produced in a recycling process for used oils that was in use in the forties and fifties of the last century. The resin-like material is highly contaminated with mineral oil hydrocarbons, extremely acidic and co-contaminated with substituted and aromatic hydrocarbons, and heavy metals. To determine the potential for microbial biodegradation the acid resin deposit and its surroundings were screened for microbial activity by soil respiration measurements. No microbial activity was found in the core deposit. However, biodegradation of hydrocarbons was possible in zones with a lower degree of contamination surrounding the deposit. An extreme acidophilic microbial community was detected close to the core deposit. With a simple ecotoxicological approach it could be shown that the pure acid resin that formed the major part of the core deposit, was toxic to the indigenous microflora due to its extremely low pH of 0-1. - Acidity is the major toxic factor of the extremely hydrophobic and acidic mixed contamination found in an acid resin deposit

Study on surface geochemistry and microbiology for hydrocarbon exploration

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

The test results of the experimental device for extraction of dissolved gases from water show that the device can be utilized for the gas geochemistry of water. The device is capable of determining hydrocarbon gases in water to the concentration of less than 5 x 10{sup -4} ml/l of water. According to the results of microbiological studies, the plate count technique can be a useful supplementary method for hydrocarbon exploration. This is based on the facts that the average survival rate to hydrocarbons (pentane, hexane) for heterotrophs is higher in the area known as containing considerable hydrocarbon gases than other areas in the Pohang region. However, it is still necessary to develop techniques to treat the bacteria with gaseous hydrocarbons. (author). 2 figs., 41 tabs.

On the thermo-chemical origin of the stratified region at the top of the Earth's core

Science.gov (United States)

Nakagawa, Takashi

2018-03-01

I developed a combined model of the thermal and chemical evolution of the Earth's core and investigated its influence on a thermochemically stable region beneath the core-mantle boundary (CMB). The chemical effects of the growing stable region are caused by the equilibrium chemical reaction between silicate and the metallic core. The thermal effects can be characterized by the growth of the sub-isentropic shell, which may have a rapid growth rate compared to that of the chemically stable region. When the present-day CMB heat flow was varied, the origin of the stable region changed from chemical to thermochemical to purely thermal because the rapid growth of the sub-isentropic shell can replace the chemically stable region. Physically reasonable values of the present-day CMB heat flow that can maintain the geodynamo action over 4 billion years should be between 8 and 11 TW. To constrain the thickness of the thermochemically stable region beneath the CMB, the chemical diffusivity is important and should be ∼O(10-8) m2/s to obtain a thickness of the thermochemically stable region beneath the CMB consistent with that inferred from geomagnetic secular variations (140 km). However, the strength of the stable region found in this study is too high to be consistent with the constraint on the stability of the stable region inferred from geomagnetic secular variations.

Relationship between polycyclic aromatic hydrocarbons (PAHs) and particle size in dated core sediments in Lake Lianhuan, Northeast China

Energy Technology Data Exchange (ETDEWEB)

Sun, Li; Zang, Shuying, E-mail: zsy6311@163.com

2013-09-01

Atmospheric particle associated with pyrogenic polycyclic aromatic hydrocarbons (PAHs) poses serious threats to human health by inhalation exposure, especially in semiarid areas. Hence, the distributions of PAHs and particle size in two core sediments collected from Lake Lianhuan, Northeast China were studied. The sediments were dated radiometrically, and particle size distribution and PAH concentration were evaluated and potential human health risk was assessed. From 1980 to 2007, the dominant PAHs in the two cores were 2- and 3-ring PAHs, and the concentrations of 3–6 ring PAHs gradually increased from the early 1990s. Diagnostic ratios indicated that pyrogenic PAHs were the main sources of PAHs which changed over time from combustions of wood and coal to liquid fossil fuel sources. Fine particles (< 65 μm) were the predominant particle size (56–97%). Lacustrine source (with the peak towards 200–400 μm) and eolian sources derived from short (2.0–10 and 30–65 μm) and long (0.4–1.0 μm) distance suspension were indentified from frequency distribution pattern of particle size. Significant correlations between 3–6 ring PAHs (especially carcinogenic 5–6 ring PAHs) and 10–35 μm particulate fractions indicated that eolian particles played an important role in adsorbing pyrogenic PAHs. Petroleum source of PAHs was only identified during the 1980s in one core sediments, in which positive correlations between 2-ring PAHs and particulate fractions of > 125 μm were found. Future research should focus on the seven carcinogenic pyrogenic PAHs due to a rapidly increasing trend since 1995 based on the assessment of toxic equivalency factors. - Highlights: • PAHs and particle size in core sediments were used to evaluate the role of eolian particles in delivering pyrogenic PAHs. • Changes of PAH sources closely followed local historical socioeconomic development since 1980s. • Changes of particulate sources from eolian to lacustrine reflected the

Petroleum hydrocarbon concentrations in eight mollusc species along Tamilnadu coast, Bay of Bengal, India.

Science.gov (United States)

Veerasingam, S; Venkatachalapathy, R; Sudhakar, S; Raja, P; Rajeswari, V

2011-01-01

Eight mollusc species and sediment samples collected from three different stations along Tamilnadu coast, Bay of Bengal, India were analysed for the levels of petroleum hydrocarbons to elucidate the status of the petroleum residues in mollusc meant for human consumption. The concentrations of petroleum hydrocarbons in sediments along Tamilnadu coast varied from 5.04-25.5 microg/g dw (dry weight). High concentration of petroleum hydrocarbons in the sediment of Uppanar estuary (25.5 +/- 1.45 microg/g dw) was perhaps land and marine based anthropogenic sources of this region. The petroleum hydrocarbon residues in eight mollusc species collected from Uppanar, Vellar and Coleroon estuaries varied between 2.44-6.04 microg/g ww (wet weight). Although the concentration of petroleum hydrocarbons in sediment of the Uppanar region was markedly higher than the background, the petroleum hydrocarbon residues in mollusc collected from Uppanar estuary did not suggest bioaccumulation. The results signified that industrial growth has affected the aquatic environments and regular monitoring will help to adopt stringent pollution control measures for better management of the aquatic region.

Magnetized Converging Flows toward the Hot Core in the Intermediate/High-mass Star-forming Region NGC 6334 V

International Nuclear Information System (INIS)

Juárez, Carmen; Girart, Josep M.; Zamora-Avilés, Manuel; Palau, Aina; Ballesteros-Paredes, Javier; Tang, Ya-Wen; Koch, Patrick M.; Liu, Hauyu Baobab; Zhang, Qizhou; Qiu, Keping

2017-01-01

We present Submillimeter Array (SMA) observations at 345 GHz toward the intermediate/high-mass cluster-forming region NGC 6334 V. From the dust emission we spatially resolve three dense condensations, the brightest one presenting the typical chemistry of a hot core. The magnetic field (derived from the dust polarized emission) shows a bimodal converging pattern toward the hot core. The molecular emission traces two filamentary structures at two different velocities, separated by 2 km s −1 , converging to the hot core and following the magnetic field distribution. We compare the velocity field and the magnetic field derived from the SMA observations with magnetohydrodynamic simulations of star-forming regions dominated by gravity. This comparison allows us to show how the gas falls in from the larger-scale extended dense core (∼0.1 pc) of NGC 6334 V toward the higher-density hot core region (∼0.02 pc) through two distinctive converging flows dragging the magnetic field, whose strength seems to have been overcome by gravity.

Sources and deposition of polycyclic aromatic hydrocarbons to western US national parks

Science.gov (United States)

Seasonal snowpack, lichens, and lake sediment cores were collected from fourteen lake catchments in eight western U.S. National Parks and analyzed for sixteen polycyclic aromatic hydrocarbons (PAHs) to determine their current and historical deposition, as well as to identify thei...

Hydrocarbons in Deep-Sea Sediments following the 2010 Deepwater Horizon Blowout in the Northeast Gulf of Mexico.

Directory of Open Access Journals (Sweden)

Isabel C Romero

Full Text Available The Deepwater Horizon (DWH spill released 4.9 million barrels of oil into the Gulf of Mexico (GoM over 87 days. Sediment and water sampling efforts were concentrated SW of the DWH and in coastal areas. Here we present geochemistry data from sediment cores collected in the aftermath of the DWH event from 1000-1500 m water depth in the DeSoto Canyon, NE of the DWH wellhead. Cores were analyzed at high-resolution (at 2 mm and 5 mm intervals in order to evaluate the concentration, composition and input of hydrocarbons to the seafloor. Specifically, we analyzed total organic carbon (TOC, aliphatic, polycyclic aromatic hydrocarbon (PAHs, and biomarker (hopanes, steranes, diasteranes compounds to elucidate possible sources and transport pathways for deposition of hydrocarbons. Results showed higher hydrocarbon concentrations during 2010-2011 compared to years prior to 2010. Hydrocarbon inputs in 2010-2011 were composed of a mixture of sources including terrestrial, planktonic, and weathered oil. Our results suggest that after the DWH event, both soluble and highly insoluble hydrocarbons were deposited at enhanced rates in the deep-sea. We proposed two distinct transport pathways of hydrocarbon deposition: 1 sinking of oil-particle aggregates (hydrocarbon-contaminated marine snow and/or suspended particulate material, and 2 advective transport and direct contact of the deep plume with the continental slope surface sediments between 1000-1200 m. Our findings underline the complexity of the depositional event observed in the aftermath of the DWH event in terms of multiple sources, variable concentrations, and spatial (depth-related variability in the DeSoto Canyon, NE of the DWH wellhead.

Magnetized Converging Flows toward the Hot Core in the Intermediate/High-mass Star-forming Region NGC 6334 V

Energy Technology Data Exchange (ETDEWEB)

Juárez, Carmen; Girart, Josep M. [Institut de Ciències de l’Espai, (CSIC-IEEC), Campus UAB, Carrer de Can Magrans, S/N, E-08193 Cerdanyola del Vallès, Catalonia (Spain); Zamora-Avilés, Manuel; Palau, Aina; Ballesteros-Paredes, Javier [Instituto de Radioastronomía y Astrofísica, Universidad Nacional Autónoma de México, P.O. Box 3-72, 58090, Morelia, Michoacán (Mexico); Tang, Ya-Wen; Koch, Patrick M.; Liu, Hauyu Baobab [Academia Sinica Institute of Astronomy and Astrophysics, P.O. Box 23-141, Taipei, 10617, Taiwan (China); Zhang, Qizhou [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Qiu, Keping, E-mail: juarez@ice.cat [School of Astronomy and Space Science, Nanjing University, 163 Xianlin Avenue, Nanjing 210023 (China)

2017-07-20

We present Submillimeter Array (SMA) observations at 345 GHz toward the intermediate/high-mass cluster-forming region NGC 6334 V. From the dust emission we spatially resolve three dense condensations, the brightest one presenting the typical chemistry of a hot core. The magnetic field (derived from the dust polarized emission) shows a bimodal converging pattern toward the hot core. The molecular emission traces two filamentary structures at two different velocities, separated by 2 km s{sup −1}, converging to the hot core and following the magnetic field distribution. We compare the velocity field and the magnetic field derived from the SMA observations with magnetohydrodynamic simulations of star-forming regions dominated by gravity. This comparison allows us to show how the gas falls in from the larger-scale extended dense core (∼0.1 pc) of NGC 6334 V toward the higher-density hot core region (∼0.02 pc) through two distinctive converging flows dragging the magnetic field, whose strength seems to have been overcome by gravity.

Hydrocarbons in the suspended matter and the bottom sediments in different regions of the Black Sea Russian sector

Directory of Open Access Journals (Sweden)

I. A. Nemirovskaya

2017-08-01

Full Text Available Content and composition of hydrocarbons (mainly the aliphatic ones in the suspended matter and the bottom sediments in the Gelendzhik Bay, the Big Sochi water area, the Feodosiya Bay and the Black Sea central part are defined and compared with the total organic carbon and chlorophyll a contents. It is shown that the aliphatic hydrocarbon concentrations exceeding the background ones are found only in the coastal zone. Advancing to the pelagic zone is accompanied by sharp decrease of their concentrations. Petroleum and pyrogenic hydrocarbons are mainly manifested in the polycyclic aromatic hydrocarbons composition. Influence of construction of the Olympic facilities upon distribution of hydrocarbons in the Big Sochi water area was of short duration, and already by 2015 the aliphatic hydrocarbons concentration decreased, on the average, up to 24 µg/l in the surface waters, and up to 18 µg/g – in the bottom sediments. Accumulation of hydrocarbons took place in bottom sediments, where their concentrations exceeded the background ones in terms of dry weight. In the Gelendzhik Bay, their content reached 252 μg/g, and in the composition of organic carbon (Corg > 1 %, which may indicate the contamination of sediments with oil products. In the Feodosiya Bay their part in the composition of Corg did not exceed 0.73 % and was 0.35 % on average. Natural alkanes dominated in the composition of aliphatic hydrocarbons. The bottom sediments are characterized by the predominance of odd high-molecular terrigenous alkanes. The content of polycyclic aromatic hydrocarbons in the studied sediments was rather low: up to 31 ng/g in the Gelendzhik Bay, up to 348 ng/g in the Feodosiya Bay. These concentrations according to the EPA classification are considered background, or minor petroleum hydrocarbons increase the level of aliphatic hydrocarbons in water and sediments, thus creating a modern hydrocarbon background.

Gamma ray spectrometry logs as a hydrocarbon indicator for clastic reservoir rocks in Egypt

International Nuclear Information System (INIS)

Al-Alfy, I.M.; Nabih, M.A.; Eysa, E.A.

2013-01-01

Petroleum oil is an important source for the energy in the world. The Gulf of Suez, Nile Delta and South Valley are important regions for studying hydrocarbon potential in Egypt. A thorium normalization technique was applied on the sandstone reservoirs in the three regions to determine the hydrocarbon potentialities zones using the three spectrometric radioactive gamma ray-logs (eU, eTh and K% logs). The conventional well logs (gamma-ray, deep resistivity, shallow resistivity, neutron, density and sonic logs) are analyzed to determine the net pay zones in these wells. Indices derived from thorium normalized spectral logs indicate the hydrocarbon zones in petroleum reservoirs. The results of this technique in the three regions (Gulf of Suez, Nile Delta and South Valley) are in agreement with the results of the conventional well log analyses by ratios of 82%, 78% and 71% respectively. - Highlights: ► The positive DRAD values indicate the hydrocarbon zones in petroleum reservoirs. ► Thorium normalization was applied to determine the hydrocarbon potentialities. ► The conventional well logs are analyzed to determine the net pay zones in wells. ► Determining hydrocarbon potentialities zones using spectrometric gamma-ray logs

Aromatic hydrocarbons

International Nuclear Information System (INIS)

Roder, M.

1985-01-01

Papers dealing with radiolysis of aromatic hydrocarbons of different composition (from benzene to terphenyls and hydrocarbons with condensed rings) as well as their mixtures (with alkanes, alkenes, other aromatic hydrocarbons) are reviewed. High radiation stability of aromatic hydrocarbons in condensed phases associated with peculiarities of molecular structure of compounds is underlined. Mechanisms of radiolytic processes, vaues of product yields are considered

World-wide and regional intercomparison for the determination of organochlorine compounds and petroleum hydrocarbons in mussel sample IAEA-142. Report no. 59

International Nuclear Information System (INIS)

Villeneuve, J.P.; Horvat, M.; Cattini, C.

1996-03-01

The accurate and precise determination of organochlorine compounds and petroleum hydrocarbons in marine environmental samples is an important aspect of marine pollution assessments in coastal and ocean environments. Intercomparison exercises represent an essential element of method testing and are used as a basic tool for evaluating data quality on a global and regional level. The Marine Environmental Studies Laboratory (MESL) of IAEA-MEL has conducted intercomparison exercises on trace organic compounds for over nineteen years as part of its contribution to IAEA's analytical quality control service and UNEP's regional seas programme, and occasionally in association with the intergovernmental oceanographic commission (of UNESCO) GIPME programme. These exercises are organized on a continuous basis, at least once per year. Result of previous exercises have revealed serious problems for many regional laboratories to obtain comparable data. As a consequence of this situation, it was decided to seek increased support for quality assurance programmes. Staff of MESL, with funding from UNEP, the World Bank and regional trust funds, embarked on a campaign to train analysts in modern measurement techniques, supply appropriate and reliable reference methods and materials and, where possible, to improve analytical instruments in Member State laboratories. This report describes results of the IAEA/UNEP intercomparison run 142 for the chemical analysis of organochlorine compounds and petroleum hydrocarbons in a homogenised mussel sample

Repair of DNA damage induced by anthanthrene, a polycyclic aromatic hydrocarbon (PAH) without bay or fjord regions

DEFF Research Database (Denmark)

Madsen, Claus Desler; Johannessen, Christian; Rasmussen, Lene Juel

2009-01-01

Polycyclic aromatic hydrocarbons (PAHs) are environmental pollutants, formed during incomplete burning of coal, oil and gas. Several PAHs have carcinogenic and mutagenic potencies, but these compounds must be activated in order to exert their mutagenic effects. One of the principal pathways...... proposed for metabolic activation of PAHs involves the cytochrome P450 enzymes. The DNA damaging potential of cytochrome P450-activated PAHs is generally associated with their bay and fjord regions, and the DNA repair response of PAHs containing such regions has been thoroughly studied. However, little...... in response to DNA damage induced by cytochrome P450-activated anthanthrene. In cell extracts, functional nucleotide excision repair (NER) and mismatch repair (MMR) activities were necessary to trigger a response to anthanthrene metabolite-induced DNA damage. In cell cultures, NER was responsible...

Use of nuclear magnetic resonance of hydrogen in the characterization of saturated hydrocarbonic chains

International Nuclear Information System (INIS)

Costa Neto, A.; Soares, V.L.P.; Costa Neto, C.

1979-01-01

Alkanes and cycloalkanes are characterized by a methyl-methylene-methine groups proportion, the percentual absorption in prefixed regions and the pattern of the spectrum of nuclear magnetic resonance of hydrogen. The GPI is calculated from the contribution of the areas corresponding to prefixed regions of the hydrogen magnetic resonance spectra (60 Mc). These regions are (for the saturated hydrocarbons): 0,5-1,05ppm (X), 1,05ppm (Y) and 1,50-2,00ppm (Z). The validity of the index was verified for the homologous series of linear hydrocarbons and methyl-, dimethyl-, ethyl-, cyclopentyl- and cyclohexyl-branched hydrocarbons. Its application to shale oil chemistry (xistoquimica) is discussed. (author) [pt

Direct hydrocarbon exploration and gas reservoir development technology

Energy Technology Data Exchange (ETDEWEB)

Kwak, Young Hoon; Oh, Jae Ho; Jeong, Tae Jin [Korea Inst. of Geology Mining and Materials, Taejon (Korea, Republic of); and others

1995-12-01

In order to enhance the capability of petroleum exploration and development techniques, three year project (1994 - 1997) was initiated on the research of direct hydrocarbon exploration and gas reservoir development. This project consists of four sub-projects. (1) Oil(Gas) - source rock correlation technique: The overview of bio-marker parameters which are applicable to hydrocarbon exploration has been illustrated. Experimental analysis of saturated hydrocarbon and bio-markers of the Pohang E and F core samples has been carried out. (2) Study on surface geochemistry and microbiology for hydrocarbon exploration: the test results of the experimental device for extraction of dissolved gases from water show that the device can be utilized for the gas geochemistry of water. (3) Development of gas and gas condensate reservoirs: There are two types of reservoir characterization. For the reservoir formation characterization, calculation of conditional simulation was compared with that of unconditional simulation. In the reservoir fluid characterization, phase behavior calculations revealed that the component grouping is more important than the increase of number of components. (4) Numerical modeling of seismic wave propagation and full waveform inversion: Three individual sections are presented. The first one is devoted to the inversion theory in general sense. The second and the third sections deal with the frequency domain pseudo waveform inversion of seismic reflection data and refraction data respectively. (author). 180 refs., 91 figs., 60 tabs.

Sedimentary record of polycyclic aromatic hydrocarbons in a sediment core from a maar lake, Northeast China: evidence in historical atmospheric deposition.

Science.gov (United States)

Guan, Yu-Feng; Sun, Jian-Lin; Ni, Hong-Gang; Guo, Jian-Yang

2012-09-01

A maar lake is an excellent ecosystem to study the atmospheric deposition of pollutants, as its contaminants are primarily by atmospheric deposition. In this study, a sediment core from Sihailongwan Maar Lake, Northeast China, was collected and the historical atmospherically deposited polycyclic aromatic hydrocarbons (PAHs) were analyzed. The concentrations of TPAHs (the sum of the US EPA proposed 16 priority PAHs, excluding naphthalene and pyrene) ranged from 473.9 to 2289 ng g(-1) with a slow increasing stage in the deeper sediments and a sharp increasing stage in the upper sediments. The input rate of TPAHs, especially that of PAH(9) (the sum of fluoranthene, benzo(a)anthracene, chrysene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene, dibenzo(ah)anthrathene, and benzo(ghi)perylene), correlated well to the Chinese historical socioeconomic data. This indicates that sediment PAHs were mainly derived from human activities and PAH(9) can be regarded as a better indicator of the local socioeconomic development. Source identification suggested that PAHs were originated primarily from mixed sources (e.g., coal and biomass burning and petroleum combustion), except for perylene which was mostly of diagenetic origin. In addition, the down-core PAHs profile clearly illustrated that PAHs sources in Northeast China experienced a transformation from low- and moderate temperature to high-temperature combustion processes, especially after the late 1980s. Additionally, an ecological risk assessment using two redefined biological thresholds (TEQ(ERL) and TEQ(ERM)) indicated that most of the PAHs measured in the present sediment core would not cause an immediate toxic effect; only FLU and PHEN are a potential source of concern for biological impairment.

Structure analysis and core community detection of embodied resources networks among regional industries

Science.gov (United States)

He, Xijun; Dong, Yanbo; Wu, Yuying; Wei, Guodan; Xing, Lizhi; Yan, Jia

2017-08-01

To address the double pressure of scarce resources and regional industrial isomorphism, this paper applied the concepts of exergy and embodied resources based on economic input-output (I-O) data. We constructed the embodied resources networks among the regional industries of Beijing-Tianjin-Hebei (also known as Jing-Jin-Ji) in China. We analyzed the rules of embodied resources consumption in the area's industries, identified the core community structures, and studied the characteristics of industrial homogeneity through regional comparisons. The results showed that the dependence on scarce resources of industrial operations in Beijing was less than in Jin-Ji, while the dependence on finance, technology, information, and other service resources in Beijing was higher than in Jin-Ji. The I-O efficiency of embodied resources among industries and the agglomeration of correlation relationships in industries with large embodied resources were higher than in Jin-Ji. The industrial coincidence degree in the ;bridge; industries and in the core community in Jin-Ji was higher than in Jing-Jin and Jing-Ji, which means the industrial homogeneous competition of Jin-Ji was higher, too. This study makes a significant contribution toward promoting the dislocation development of regional industries, accelerating the coordination of resources, and reducing homogeneity competition.

Reactor core and initially loaded reactor core of nuclear reactor

International Nuclear Information System (INIS)

Koyama, Jun-ichi; Aoyama, Motoo.

1989-01-01

In BWR type reactors, improvement for the reactor shutdown margin is an important characteristic condition togehter with power distribution flattening . However, in the reactor core at high burnup degree, the reactor shutdown margin is different depending on the radial position of the reactor core. That is , the reactor shutdown margin is smaller in the outer peripheral region than in the central region of the reactor core. In view of the above, the reactor core is divided radially into a central region and as outer region. The amount of fissionable material of first fuel assemblies newly loaded in the outer region is made less than the amount of the fissionable material of second fuel assemblies newly loaded in the central region, to thereby improve the reactor shutdown margin in the outer region. Further, the ratio between the amount of the fissionable material in the upper region and that of the fissionable material in the lower portion of the first fuel assemblies is made smaller than the ratio between the amount of the fissionable material in the upper region and that of the fissionable material in the lower region of the second fuel assemblies, to thereby obtain a sufficient thermal margin in the central region. (K.M.)

Differences in neurogenesis differentiate between core and shell regions of auditory nuclei in the turtle (Pelodiscus sinensis): evolutionary implications.

Science.gov (United States)

Zeng, Shao-Ju; Xi, Chao; Zhang, Xin-Wen; Zuo, Ming-Xue

2007-01-01

There is a clear core-versus-shell distinction in cytoarchitecture, electrophysiological properties and neural connections in the mesencephalic and diencephalic auditory nuclei of amniotes. Determining whether the embryogenesis of auditory nuclei shows a similar organization is helpful for further understanding the constituent organization and evolution of auditory nuclei. Therefore in the present study, we injected [(3)H]-thymidine into turtle embryos (Pelodiscus sinensis) at various stages of development. Upon hatching, [(3)H]-thymidine labeling was examined in both the core and shell auditory regions in the midbrain, diencephalon and dorsal ventricular ridge. Met-enkephalin and substance P immunohistochemistry was used to distinguish the core and shell regions. In the mesencephalic auditory nucleus, the occurrence of heavily labeled neurons in the nucleus centralis of the torus semicircularis reached its peak at embryonic day 9, one day later than the surrounding shell. In the diencephalic auditory nucleus, the production of heavily labeled neurons in the central region of the reuniens (Re) was highest at embryonic day (E) 8, one day later than that in the shell region of reuniens. In the region of the dorsal ventricular ridge that received inputs from the central region of Re, the appearance of heavily labeled neurons also reached a peak one day later than that in the area receiving inputs from the shell region of reuniens. Thus, there is a core-versus-shell organization of neuronal generation in reptilian auditory areas. Copyright (c) 2007 S. Karger AG, Basel.

Determination of polynuclear aromatic hydrocarbons (PAHs) in ...

African Journals Online (AJOL)

AJB SERVER

2006-11-02

Nov 2, 2006 ... Several water bodies in the Niger Delta region of Nigeria where extensive crude oil ..... hydrocarbons (PAHs) in fish from the Red Sea Coast of Yemem. ... smoked meat products and smoke flavouring food additives. J.

Hydrocarbon-degrading sulfate-reducing bacteria in marine hydrocarbon seep sediments

OpenAIRE

Kleindienst, Sara

2012-01-01

Microorganisms are key players in our biosphere because of their ability to degrade various organic compounds including a wide range of hydrocarbons. At marine hydrocarbon seeps, more than 90% of sulfate reduction (SR) is potentially coupled to non-methane hydrocarbon oxidation. Several hydrocarbon-degrading sulfate-reducing bacteria (SRB) were enriched or isolated from marine sediments. However, in situ active SRB remained largely unknown. In the present thesis, the global distribution and a...

Reactor core for LMFBR type reactors

International Nuclear Information System (INIS)

Masumi, Ryoji; Azekura, Kazuo; Kurihara, Kunitoshi; Bando, Masaru; Watari, Yoshio.

1987-01-01

Purpose: To reduce the power distribution fluctuations and obtain flat and stable power distribution throughout the operation period in an LMFBR type reactor. Constitution: In the inner reactor core region and the outer reactor core region surrounding the same, the thickness of the inner region is made smaller than the axial height of the reactor core region and the radial width thereof is made smaller than that of the reactor core region and the volume thereof is made to 30 - 50 % for the reactor core region. Further, the amount of the fuel material per unit volume in the inner region is made to 70 - 90 % of that in the outer region. The difference in the neutron infinite multiplication factor between the inner region and the outer region is substantially constant irrespective of the burnup degree and the power distribution fluctuation can be reduced to about 2/3, by which the effect of thermal striping to the reactor core upper mechanisms can be moderated. Further, the maximum linear power during operation can be reduced by 3 %, by which the thermal margin in the reactor core is increased and the reactor core fuels can be saved by 3 %. (Kamimura, M.)

Petroleum hydrocarbon concentration in surface sediments in continental shelf region along the central west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Ram, A.; Kadam, A.N.

Gas chromatography revealed that nonpolar material extracted from surface sediments collected along the northern west coast of India was originated from petroleum hydrocarbon residue. Petroleum hydrocarbon levels as determinEd. by fluorescence...

Reactor core of FBR type reactor

International Nuclear Information System (INIS)

Hayashi, Hideyuki; Ichimiya, Masakazu.

1994-01-01

A reactor core is a homogeneous reactor core divided into two regions of an inner reactor core region at the center and an outer reactor core region surrounding the outside of the inner reactor core region. In this case, the inner reactor core region has a lower plutonium enrichment degree and less amount of neutron leakage in the radial direction, and the outer reactor core region has higher plutonium enrichment degree and greater amount of neutron leakage in the radial direction. Moderator materials containing hydrogen are added only to the inner reactor core fuels in the inner reactor core region. Pins loaded with the fuels with addition of the moderator materials are inserted at a ratio of from 3 to 10% of the total number of the fuel pins. The moderator materials containing hydrogen comprise zirconium hydride, titanium hydride, or calcium hydride. With such a constitution, fluctuation of the power distribution in the radial direction along with burning is suppressed. In addition, an absolute value of the Doppler coefficient can be increased, and a temperature coefficient of coolants can be reduced. (I.N.)

Forming of the regional core transport network taking into account the allocation of alternative energy sources based on artificial intelligence methods

OpenAIRE

Marina ZHURAVSKAYA; Vladimir TARASYAN

2014-01-01

In the modern world the alternative energy sources, which considerably depend on a region, play more and more significant role. However, the transition of regions to new energy sources lead to the change of transport and logistic network configuration. The formation of optimal core transport network today is a guarantee of the successful economic development of a region tomorrow. The present article studies the issue of advanced core transport network development in a region based on the ...

Total Petroleum Hydrocarbon Criteria Working Group (TPHCWG) Field Demonstration Report: IRP Site 4, POL Area, Springfield ANG Base, Springfield, Ohio

National Research Council Canada - National Science Library

Reed, Dennis

2003-01-01

...) methodology to compare the approaches. Soil core composites were analyzed for trichloroethylene, gasoline-range organics, volatile petroleum hydrocarbons, benzene, toluene, ethylbenzene, and xylenes...

Preliminary Geospatial Analysis of Arctic Ocean Hydrocarbon Resources

Energy Technology Data Exchange (ETDEWEB)

Long, Philip E.; Wurstner, Signe K.; Sullivan, E. C.; Schaef, Herbert T.; Bradley, Donald J.

2008-10-01

Ice coverage of the Arctic Ocean is predicted to become thinner and to cover less area with time. The combination of more ice-free waters for exploration and navigation, along with increasing demand for hydrocarbons and improvements in technologies for the discovery and exploitation of new hydrocarbon resources have focused attention on the hydrocarbon potential of the Arctic Basin and its margins. The purpose of this document is to 1) summarize results of a review of published hydrocarbon resources in the Arctic, including both conventional oil and gas and methane hydrates and 2) develop a set of digital maps of the hydrocarbon potential of the Arctic Ocean. These maps can be combined with predictions of ice-free areas to enable estimates of the likely regions and sequence of hydrocarbon production development in the Arctic. In this report, conventional oil and gas resources are explicitly linked with potential gas hydrate resources. This has not been attempted previously and is particularly powerful as the likelihood of gas production from marine gas hydrates increases. Available or planned infrastructure, such as pipelines, combined with the geospatial distribution of hydrocarbons is a very strong determinant of the temporal-spatial development of Arctic hydrocarbon resources. Significant unknowns decrease the certainty of predictions for development of hydrocarbon resources. These include: 1) Areas in the Russian Arctic that are poorly mapped, 2) Disputed ownership: primarily the Lomonosov Ridge, 3) Lack of detailed information on gas hydrate distribution, and 4) Technical risk associated with the ability to extract methane gas from gas hydrates. Logistics may control areas of exploration more than hydrocarbon potential. Accessibility, established ownership, and leasing of exploration blocks may trump quality of source rock, reservoir, and size of target. With this in mind, the main areas that are likely to be explored first are the Bering Strait and Chukchi

Coupling spectroscopic and chromatographic techniques for evaluation of the depositional history of hydrocarbons in a subtropical estuary

International Nuclear Information System (INIS)

Martins, César C.; Doumer, Marta E.; Gallice, Wellington C.; Dauner, Ana Lúcia L.; Cabral, Ana Caroline; Cardoso, Fernanda D.

2015-01-01

Spectroscopic and chromatographic techniques can be used together to evaluate hydrocarbon inputs to coastal environments such as the Paranaguá estuarine system (PES), located in the SW Atlantic, Brazil. Historical inputs of aliphatic hydrocarbons (AHs) and polycyclic aromatic hydrocarbons (PAHs) were analyzed using two sediment cores from the PES. The AHs were related to the presence of biogenic organic matter and degraded oil residues. The PAHs were associated with mixed sources. The highest hydrocarbon concentrations were related to oil spills, while relatively low levels could be attributed to the decrease in oil usage during the global oil crisis. The results of electron paramagnetic resonance were in agreement with the absolute AHs and PAHs concentrations measured by chromatographic techniques, while near-infrared spectroscopy results were consistent with unresolved complex mixture (UCM)/total n-alkanes ratios. These findings suggest that the use of a combination of techniques can increase the accuracy of assessment of contamination in sediments. - Highlights: • Historical inputs of hydrocarbons in a subtropical estuary were evaluated. • Spectroscopic and chromatographic methods were used in combination. • High hydrocarbon concentrations were related to anthropogenic activities. • Low hydrocarbon levels could be explained by the 1970s global oil crisis. - Spectroscopic and chromatographic techniques could be used together to evaluate hydrocarbon inputs to coastal environments

Hiding the interior region of core-shell nanoparticles with quantum invisible cloaks

Science.gov (United States)

Lee, Jeng Yi; Lee, Ray-Kuang

2014-04-01

Based on the scattering cancellation, we provide a method not only making a nanoparticle nearly invisible, but also hiding its interior region from the outside probing matter wave. By applying the interplay among the nodal points of partial waves along with the concept of streamline in fluid dynamics for probability flux, a quantum invisible cloak to the electron transport in a host semiconductor is demonstrated by simultaneously guiding the probability flux outside a hidden region and keeping the total scattering cross section negligible. As the probability flux vanishes in the interior region, one can embed any materials inside a multiple core-shell nanoparticle without affecting physical observables from the outside. Our results reveal the possibility to design a protection shield layer for fragile interior parts from the impact of transport electrons.

Molecular Tracers of Saturated and Polycyclic Aromatic Hydrocarbon Inputs into Central Park Lake, New York City

Science.gov (United States)

YAN, BEIZHAN; ABRAJANO, TEOFILO A.; BOPP, RICHARD F.; CHAKY, DAMON A.; BENEDICT, LUCILLE A.; CHILLRUD, STEVEN N.

2011-01-01

Saturated hydrocarbons (SH) and polycyclic aromatic hydrocarbons (PAHs) have been quantified in a sediment core obtained from Central Park Lake, New York City. Radionuclides 210Pb and 137Cs were used to assign approximate dates to each individual section in the core. The dating profile based on 210Pb matches very well with the time constraints provided by 137Cs. Radionuclide-derived depositional dates are consistent with temporal information from the petroleum-indicator ratio U/R [the ratio of unresolved complex mixture (UCM) to saturated hydrocarbons in the aliphatic fraction] and the history of fuel use in the NYC area. Ratios of 1,7-dimethylphenanthrane (DMP) to 1,7-DMP plus 2,6-DMP [1,7/(1,7 + 2,6)-DMP], retene to retene plus chrysene [Ret/(Ret + Chy)], and fluoranthene to fluoranthene plus pyrene [Fl/(Fl + Py)] provide additional source discrimination throughout the core. Results show that the ratio U/R is sensitive to petroleum inputs and Ret/(Ret + Chy) is responsive to contributions from softwood combustion, whereas both Fl/(Fl + Py) and 1,7/(1,7 + 2,6)-DMP can be used to discriminate among wood, coal, and petroleum combustion sources. Combined use of these ratios suggests that in New York City, wood combustion dominated 100 years ago, with a shift to coal combustion occurring from the 1900s to the 1950s. Petroleum use began around the 1920s and has dominated since the 1940s. PMID:16201624

The north-east Baffin Bay region, offshore Greenland - a new frontier petroleum exploration region

Energy Technology Data Exchange (ETDEWEB)

Gregersen, U. (Geological Survey of Denmark and Greenland, Copenhagen (Denmark))

2008-07-15

In recent years the Arctic has come into focus for hydrocarbon exploration, and areas offshore both West and East Greenland have been evaluated as promising frontier hydrocarbon provinces. Seven hydrocarbon exploration and exploitation licenses were awarded in 2007-2008 offshore the Disko-Nuussuaq region, and two more have been awarded in the open-door region offshore south-western Greenland. In 2007, an extensive amount of new seismic and aero-magnetic data was acquired by the TGS-NOPEC Geophysical Company in the north-eastern Baffin Bay region. Geophysical mapping has been initiated by the Geological Survey of Denmark and Greenland (GEUS) in the Melville Bugt region offshore North-West Greenland with the purpose of evaluating the hydrocarbon prospectivity. Initial interpretation of seismic and gravity data suggests the presence of deep sedimentary basins separated by structural highs. Geological information on source rock, reservoir rock and seal intervals from surrounding regions suggest that the Melville Bugt region is likely to have a significant petroleum potential. The study is based on public domain magnetic and gravity data, and all proprietary and public 2-D seismic data acquired before 2003. Seismic horizons from the 'seismic basement' to 'base Quaternary' are being interpreted regionally. Based on the seismic interpretation, a structural element map, depth-structure maps and isopach maps will be produced in order to assess the prospectivity of the Melville Bugt region. (au)

Dissolved petroleum hydrocarbon concentrations in some regions of the northern Indian Ocean

Digital Repository Service at National Institute of Oceanography (India)

SenGupta, R.; Qasim, S.Z.; Fondekar, S.P.; Topgi, R.S.

Dissolved petroleum hydrocarbons were measured in some parts of the Northern Indian Ocean using UV bsorbance technique with a clean up step. The concentration of oil ranged from 0.6 to 26.5 mu gl. Higher values were recorded along the oil tanker...

Effect of heat transfer in the fog region during core reflooding

International Nuclear Information System (INIS)

Rouai, N. M.; El-sawy, H. M.

1993-01-01

Core reflooding following a loss of coolant accident (LOCA) in a pressurized water reactor (PWR) received considerable attention during the past thirty years. In this paper a one dimensional model is used to study the effect of the heat transfer in the fog region ahead of the wet front reflooding rate of a cylindrical fuel element following a LOCA in a PWR. The heat conduction equation in the cladding is solved in coordinate system moving with the wet front under a variety of condition to investigate the effects of such parameters as the initial cladding surface temperature, the decay heat generation rate in the fuel and the mode of heat transfer prevailing. The cladding surface is divided into three axial regions according to the mechanism of heat transfer, namely, a boiling region behind the wet front, a fog region ahead of the wet front and a dry region further downstream of the wet front. The effect of changing the heat transfer coefficient in the fog region on the rewetting rate and on the fog length is investigated. The results of this simple model show that increasing the heat transfer in the fog region increases the rewetting velocity and consequently decreases the fog length. The results are in general agreement with a more accurate two-dimensional model and experimental data. (author)

Identifying regions of strong scattering at the core-mantle boundary from analysis of PKKP precursor energy

Science.gov (United States)

Rost, S.; Earle, P.S.

2010-01-01

We detect seismic scattering from the core-mantle boundary related to the phase PKKP (PK. KP) in data from small aperture seismic arrays in India and Canada. The detection of these scattered waves in data from small aperture arrays is new and allows a better characterization of the fine-scale structure of the deep Earth especially in the southern hemisphere. Their slowness vector is determined from array processing allowing location of the heterogeneities at the core-mantle boundary using back-projection techniques through 1D Earth models. We identify strong scattering at the core-mantle boundary (CMB) beneath the Caribbean, Patagonia and the Antarctic Peninsula as well as beneath southern Africa. An analysis of the scattering regions relative to sources and receivers indicates that these regions represent areas of increased scattering likely due to increased heterogeneities close to the CMB. The 1. Hz array data used in this study is most sensitive to heterogeneity with scale lengths of about 10. km. Given the small size of the scatterers, a chemical origin of the heterogeneities is likely. By comparing the location of the fine-scale heterogeneity to geodynamical models and tomographic images, we identify different scattering mechanisms in regions related to subduction (Caribbean and Patagonia) and dense thermo chemical piles (Southern Africa). ?? 2010 Elsevier B.V.

Magnetic susceptibility measurements of boring cores obtained from regional hydrological study project

International Nuclear Information System (INIS)

Hasegawa, Ken

2010-02-01

We measured the magnetic susceptibility of boring cores obtained from the Regional Hydrological Study Project to interpret the aeromagnetic survey data which was carried out in Tono area with about 40km square surrounding Tono Geoscience Center. The result of measurements indicates that the magnetic susceptibility of the Toki Granite is not distributed uniformly and the maximum value becomes two orders in magnitude larger than its minimum value. (author)

CHEMICAL SEGREGATION TOWARD MASSIVE HOT CORES: THE AFGL2591 STAR-FORMING REGION

Energy Technology Data Exchange (ETDEWEB)

Jimenez-Serra, I.; Zhang, Q. [Harvard-Smithsonian Center for Astrophysics, 60 Garden St., Cambridge, MA 02138 (United States); Viti, S. [Department of Physics and Astronomy, University College London, Gower Place, London WC1E 6BT (United Kingdom); Martin-Pintado, J. [Centro de Astrobiologia (CSIC/INTA), Ctra. de Torrejon a Ajalvir km 4, E-28850 Torrejon de Ardoz, Madrid (Spain); De Wit, W.-J., E-mail: ijimenez-serra@cfa.harvard.edu, E-mail: qzhang@cfa.harvard.edu, E-mail: sv@star.ucl.ac.uk, E-mail: jmartin@cab.inta-csic.es, E-mail: wdewit@eso.org [European Southern Observatory, Alonso de Cordova 3107, Vitacura, Santiago (Chile)

2012-07-01

We present high angular resolution observations (0.''5 Multiplication-Sign 0.''3) carried out with the Submillimeter Array (SMA) toward the AFGL2591 high-mass star-forming region. Our SMA images reveal a clear chemical segregation within the AFGL2591 VLA 3 hot core, where different molecular species (Types I, II, and III) appear distributed in three concentric shells. This is the first time that such a chemical segregation is ever reported at linear scales {<=}3000 AU within a hot core. While Type I species (H{sub 2}S and {sup 13}CS) peak at the AFGL2591 VLA 3 protostar, Type II molecules (HC{sub 3}N, OCS, SO, and SO{sub 2}) show a double-peaked structure circumventing the continuum peak. Type III species, represented by CH{sub 3}OH, form a ring-like structure surrounding the continuum emission. The excitation temperatures of SO{sub 2}, HC{sub 3}N, and CH{sub 3}OH (185 {+-} 11 K, 150 {+-} 20 K, and 124 {+-} 12 K, respectively) show a temperature gradient within the AFGL2591 VLA 3 envelope, consistent with previous observations and modeling of the source. By combining the H{sub 2}S, SO{sub 2}, and CH{sub 3}OH images, representative of the three concentric shells, we find that the global kinematics of the molecular gas follow Keplerian-like rotation around a 40 M{sub Sun} star. The chemical segregation observed toward AFGL2591 VLA 3 is explained by the combination of molecular UV photodissociation and a high-temperature ({approx}1000 K) gas-phase chemistry within the low extinction innermost region in the AFGL2591 VLA 3 hot core.

Petroleum hydrocarbon concentrations in ten commercial fish species along Tamilnadu coast, Bay of Bengal, India.

Science.gov (United States)

Veerasingam, S; Venkatachalapathy, R; Raja, P; Sudhakar, S; Rajeswari, V; Asanulla, R Mohamed; Mohan, R; Sutharsan, P

2011-05-01

The aim of the present study was to evaluate the distribution of petroleum hydrocarbons in ten commercial fish species and water samples in three estuaries along Tamilnadu coast, Bay of Bengal, India. Fish and water samples collected from Tamilnadu coast, India, were extracted and analyzed for petroleum hydrocarbons by ultraviolet fluorescence (UVF) spectroscopy. The petroleum hydrocarbon concentration (PHC) in coastal waters and fish species varied between 2.28 and 14.02 μg/l and 0.52 and 2.05 μg/g, respectively. The highest PHC concentration was obtained in Uppanar estuarine waters (14.02 ± 0.83) and the lowest was observed in Vellar estuarine waters (2.28 ± 0.25). Among the ten fish species, Sardinella longiceps have high PHC concentration from all the locations. This study suggests that S. longiceps can be used as a good biological indicator for petroleum hydrocarbon pollution in water. The concentration of petroleum hydrocarbons in coastal waters along Tamilnadu coast is markedly higher than that in the background, but there is no evidence for its increase in fish of this region. From a public health point, petroleum hydrocarbon residue levels in all fish samples analyzed in this study are considerably lower than the hazardous levels. At present, as Tamilnadu coastal area is in a rapid development stage of new harbour, chemical industries, power plants, oil exploration and other large-scale industries, further assessment of petroleum hydrocarbons and the various hydrodynamic conditions acting in the region are to be studied in detail and continuous pollution monitoring studies should be conducted for improving the aquatic environment. The results will also be useful for pollution monitoring program along the coastal region and also to check the levels of petroleum hydrocarbons.

The plasma-wall interaction region: a key low temperature plasma for controlled fusion

International Nuclear Information System (INIS)

Counsell, G F

2002-01-01

The plasma-wall interaction region of a fusion device provides the interface between the hot core plasma and the material surfaces. To obtain acceptably low levels of erosion from these surfaces requires most of the power leaving the core to be radiated. This is accomplished in existing devices by encouraging plasma detachment, in which the hot plasma arriving in the region is cooled by volume recombination and ion-neutral momentum transfer with a dense population of neutrals recycled from the surface. The result is a low temperature (1 eV e e >10 19 m -3 ) but weakly ionized (n 0 >10 20 m -3 , n e /n 0 <0.1) plasma found nowhere else in the fusion environment. This plasma provides many of the conditions found in industrial plasmas exploiting plasma chemistry and the presence of carbon in the region (in the form of carbon-fibre composite used in the plasma facing materials) can result in the formation of deposited hydrocarbon films. The plasma-wall interaction region is therefore among the most difficult in fusion to model, requiring an understanding of atomic, molecular and surface physics issues

Distribution and origin of hydrocarbons in water and sediment in Sao Sebastiao, SP, Brazil

International Nuclear Information System (INIS)

Zanardi, Eliete; Bicego, Marcia Caruso; Miranda, Luiz Bruner de; Weber, Rolf Roland

1999-01-01

This study describes the dissolved/dispersed petroleum hydrocarbons (DDPH) in surface water and the origin and distribution of aliphatic and aromatic hydrocarbons in samples from the surface bottom sediments. The main objective was to verify the anthropogenic contribution on the adjacent inner shelf of Sao Sebastiao, taking into account the distribution of hydrographic properties and knowledge of the main circulation. The DDPH concentration range of the 20 samples were from 0.35 to 2.50 m u g . L -1 , characterising this region as slightly affected by the contribution of petroleum hydrocarbons. Considering sediment hydrocarbon results, sites located in the inner shelf were divided into three groups: one with mainly biogenic hydrocarbons, a second one with biogenic and petroleum hydrocarbons and a third with significant contribution of petroleum hydrocarbons. These results show an influence of human activities in the Sao Sebastiao Channel on the surrounding areas of the inner shelf. (Author)

Integration of ANFIS, NN and GA to determine core porosity and permeability from conventional well log data

Science.gov (United States)

Ja'fari, Ahmad; Hamidzadeh Moghadam, Rasoul

2012-10-01

Routine core analysis provides useful information for petrophysical study of the hydrocarbon reservoirs. Effective porosity and fluid conductivity (permeability) could be obtained from core analysis in laboratory. Coring hydrocarbon bearing intervals and analysis of obtained cores in laboratory is expensive and time consuming. In this study an improved method to make a quantitative correlation between porosity and permeability obtained from core and conventional well log data by integration of different artificial intelligent systems is proposed. The proposed method combines the results of adaptive neuro-fuzzy inference system (ANFIS) and neural network (NN) algorithms for overall estimation of core data from conventional well log data. These methods multiply the output of each algorithm with a weight factor. Simple averaging and weighted averaging were used for determining the weight factors. In the weighted averaging method the genetic algorithm (GA) is used to determine the weight factors. The overall algorithm was applied in one of SW Iran’s oil fields with two cored wells. One-third of all data were used as the test dataset and the rest of them were used for training the networks. Results show that the output of the GA averaging method provided the best mean square error and also the best correlation coefficient with real core data.

Integration of ANFIS, NN and GA to determine core porosity and permeability from conventional well log data

International Nuclear Information System (INIS)

Ja’fari, Ahmad; Moghadam, Rasoul Hamidzadeh

2012-01-01

Routine core analysis provides useful information for petrophysical study of the hydrocarbon reservoirs. Effective porosity and fluid conductivity (permeability) could be obtained from core analysis in laboratory. Coring hydrocarbon bearing intervals and analysis of obtained cores in laboratory is expensive and time consuming. In this study an improved method to make a quantitative correlation between porosity and permeability obtained from core and conventional well log data by integration of different artificial intelligent systems is proposed. The proposed method combines the results of adaptive neuro-fuzzy inference system (ANFIS) and neural network (NN) algorithms for overall estimation of core data from conventional well log data. These methods multiply the output of each algorithm with a weight factor. Simple averaging and weighted averaging were used for determining the weight factors. In the weighted averaging method the genetic algorithm (GA) is used to determine the weight factors. The overall algorithm was applied in one of SW Iran’s oil fields with two cored wells. One-third of all data were used as the test dataset and the rest of them were used for training the networks. Results show that the output of the GA averaging method provided the best mean square error and also the best correlation coefficient with real core data. (paper)

Plasma devices for hydrocarbon reformation

KAUST Repository

Cha, Min Suk

2017-02-16

Plasma devices for hydrocarbon reformation are provided. Methods of using the devices for hydrocarbon reformation are also provided. The devices can include a liquid container to receive a hydrocarbon source, and a plasma torch configured to be submerged in the liquid. The plasma plume from the plasma torch can cause reformation of the hydrocarbon. The device can use a variety of plasma torches that can be arranged in a variety of positions in the liquid container. The devices can be used for the reformation of gaseous hydrocarbons and/or liquid hydrocarbons. The reformation can produce methane, lower hydrocarbons, higher hydrocarbons, hydrogen gas, water, carbon dioxide, carbon monoxide, or a combination thereof.

Evaluation of mineral oil saturated hydrocarbons (MOSH and mineral oil aromatic hydrocarbons (MOAH in pure mineral hydrocarbon-based cosmetics and cosmetic raw materials using 1H NMR spectroscopy [version 2; referees: 3 approved

Directory of Open Access Journals (Sweden)

Dirk W. Lachenmeier

2017-08-01

Full Text Available Mineral hydrocarbons consist of two fractions, mineral oil saturated hydrocarbons (MOSH and mineral oil aromatic hydrocarbons (MOAH. MOAH is a potential public health hazard because it may include carcinogenic polycyclic compounds. In the present study, 400 MHz nuclear magnetic resonance (NMR spectroscopy was introduced, in the context of official controls, to measure MOSH and MOAH in raw materials or pure mineral hydrocarbon final products (cosmetics and medicinal products. Quantitative determination (qNMR has been established using the ERETIC methodology (electronic reference to access in vivo concentrations based on the PULCON principle (pulse length based concentration determination. Various mineral hydrocarbons (e.g., white oils, paraffins or petroleum jelly were dissolved in deuterated chloroform. The ERETIC factor was established using a quantification reference sample containing ethylbenzene and tetrachloronitrobenzene. The following spectral regions were integrated: MOSH δ 3.0 – 0.2 ppm and MOAH δ 9.2 - 6.5, excluding solvent signals. Validation showed a sufficient precision of the method with a coefficient of variation <6% and a limit of detection <0.1 g/100 g. The applicability of the method was proven by analysing 27 authentic samples with MOSH and MOAH contents in the range of 90-109 g/100 g and 0.02-1.10 g/100 g, respectively. It is important to distinguish this new NMR-approach from the hyphenated liquid chromatography-gas chromatography methodology previously used to characterize MOSH/MOAH amounts in cosmetic products. For mineral hydrocarbon raw materials or pure mineral hydrocarbon-based cosmetic products, NMR delivers higher specificity without any sample preparation besides dilution. Our sample survey shows that previous methods may have overestimated the MOAH amount in mineral oil products and opens new paths to characterize this fraction. Therefore, the developed method can be applied for routine monitoring of consumer

Measurements of ozone and nonmethane hydrocarbons at Chichi-jima island, a remote island in the western Pacific: long-range transport of polluted air from the Pacific rim region

Science.gov (United States)

Kato, Shungo; Pochanart, Pakpong; Kajii, Yoshizumi

Chichi-jima island is located in the Pacific about 1000 km from the Japanese main island and is an ideal remote observatory from which to assess the long-range transport of polluted air from East Asia. The ozone concentration was measured from August 1997 to August 1998. Owing to the air mass change, the seasonal variation of ozone shows a distinct character: low concentration (about 13 ppbv) for the maritime air mass during the summer, and high concentration (about 40 ppbv) for the continental air mass during the winter. To assess the contribution of the long-range transport of polluted air during winter, nonmethane hydrocarbons were also measured in December 1999. Using backward trajectory analysis, the transport time of the air mass from the source area in the Pacific rim region was calculated for each sample. The concentration of hydrocarbons shows a clear negative correlation against the transport time. This analysis clearly shows the transport of polluted air, emitted in East Asia, to the Pacific during the winter. The plots of suitable hydrocarbon pairs showed that the decrease of hydrocarbon concentrations during winter is mainly caused by the mixing with clean background air.

Electrochemical masstransfer of oil hydrocarbons in dispersed soils

Energy Technology Data Exchange (ETDEWEB)

Nekrasova, M.A.; Zvolinsky, V.P.; Kanev, M.V. [Russian Friendship Peoples Univ., Dept. of Eecological Monitoring and Forecasting, Moscow (Russian Federation)

2001-07-01

A large-scale pollution of the geological environment is a result of imperfect processes of mining, refining, haul of oil and irrational use of petroleum. The processes of masstransfer of hydrocarbons in dispersed soils and the problems of forming of a dual electric layer (DEL) on the demarcations 'water-oil' and 'mineral-water' are still insufficiently studied. Therefore, one of the most important problems in the field of the ecological geology is the analysis of ways of cleaning of soils from hydrocarbons. The kaolinitic clay from the Tirlianskoye deposit (K{sub 2}, st. Jabik, Bashkiria) and average polymineral loam (prlllkl, Moscow region, the south-east of town Zvenigorod) was chosen as the objects of the experimental study. The mixture of West Siberian oils was used for model pollution. The experimental laboratory researches of electrochemical migration of hydrocarbons were carried out on dispersiblis clayey soils. (orig.)

Distribution and origin of hydrocarbons in water and sediment in Sao Sebastiao, SP, Brazil

Energy Technology Data Exchange (ETDEWEB)

Zanardi, Eliete [Universidade de Sao Paulo, Instituto Oceanografico, Sao Paulo, SP (Brazil); Bicego, Marcia Caruso; Miranda, Luiz Bruner de; Weber, Rolf Roland [Miami Univ., RSMAS/NAC, Miami, FL (United States)

1999-04-01

This study describes the dissolved/dispersed petroleum hydrocarbons (DDPH) in surface water and the origin and distribution of aliphatic and aromatic hydrocarbons in samples from the surface bottom sediments. The main objective was to verify the anthropogenic contribution on the adjacent inner shelf of Sao Sebastiao, taking into account the distribution of hydrographic properties and knowledge of the main circulation. The DDPH concentration range of the 20 samples were from 0.35 to 2.50 {sup m}u{sup g}. L{sup -1}, characterising this region as slightly affected by the contribution of petroleum hydrocarbons. Considering sediment hydrocarbon results, sites located in the inner shelf were divided into three groups: one with mainly biogenic hydrocarbons, a second one with biogenic and petroleum hydrocarbons and a third with significant contribution of petroleum hydrocarbons. These results show an influence of human activities in the Sao Sebastiao Channel on the surrounding areas of the inner shelf. (Author)

Petroleum hydrocarbons

International Nuclear Information System (INIS)

Farrington, J.W.; Teal, J.M.; Parker, P.L.

1976-01-01

Methods for analysis of petroleum hydrocarbons in marine samples are presented. Types of hydrocarbons present and their origins are discussed. Principles and methods of analysis are outlined. Infrared spectrometry, uv spectrometry, gas chromatography, mass spectroscopy, and carbon 14 measurements are described

Hydrocarbon accumulation in deep fluid modified carbonate rock in the Tarim Basin

Institute of Scientific and Technical Information of China (English)

无

2007-01-01

The activities of deep fluid are regionalized in the Tarim Basin. By analyzing the REE in core samples and crude oil, carbon isotope of carbon dioxide and inclusion temperature measurement in the west of the Tazhong Uplift in the western Tarim Basin, all the evidence confirms the existence of deep fluid. The deep fluid below the basin floor moved up into the basin through discordogenic fauit and volcanicity to cause corrosion and metaaomatosis of carbonate rock by exchange of matter and energy. The pore structure and permeability of the carbonate reservoirs were improved, making the carbonate reservoirs an excellent type of deeply buried modification. The fluorite ore belts discovered along the large fault and the volcanic area in the west of the Tazhong Uplift are the outcome of deep fluid action. Such carbonate reservoirs are the main type of reservoirs in the Tazhong 45 oilfield. The carbonate reservoirs in well YM 7 are improved obviously by thermal fluid dolomitization. The origin and territory of deep fluid are associated with the discordogenic fault and volcanicity in the basin. The discordogenic fault and volcanic area may be the pointer of looking for the deep fluid modified reservoirs. The primary characteristics of hydrocarbon accumulation in deep fluid reconstructed carbonate rock are summarized as accumulation near the large fault and volcano passage, late-period hydrocarbon accumulation after volcanic activity, and subtle trap reservoirs controlled by lithology.

Natural and anthropogenic hydrocarbons in the Antarctic pack ice

International Nuclear Information System (INIS)

Nemirovskaya, I.A.; Novigatsky, A.N.

2004-01-01

A field experiment was conducted near the Russian Antarctic stations in May, 2001 in the Pridz Bay and coastal part of the Davies Sea to examine the content of dissolved and suspended forms of aliphatic hydrocarbons in melted snow samples, pack ice and ice cores. The site included clean control areas and polluted test areas. A spill was performed by covering the bare ice surface with marine diesel fuel. The different physical characteristics of clean and polluted ice were measured. This included radiation balance, reflected solar radiation, integral albedo radiation, surface temperature, seawater temperature, salinity at depth, and ice salinity. The study showed that accumulation of natural and anthropogenic hydrocarbon took place in the ice-water barrier zone, mostly in suspended form. It was concluded that for oil spills in pack Antarctic ice, the mechanism of filtration due to convection-diffusion plays an important role in the transformation of diesel fuel. 14 refs., 2 tabs., 2 figs

Long-term Behavior of Hydrocarbon Production Curves

Science.gov (United States)

Lovell, A.; Karra, S.; O'Malley, D.; Viswanathan, H. S.; Srinivasan, G.

2017-12-01

Recovering hydrocarbons (such as natural gas) from naturally-occurring formations with low permeability has had a huge impact on the energy sector, however, recovery rates are low due to poor understanding of recovery and transport mechanisms [1]. The physical mechanisms that control the production of hydrocarbon are only partially understood. Calculations have shown that the short-term behavior in the peak of the production curve is understood to come from the free hydrocarbons in the fracture networks, but the long-term behavior of these curves is often underpredicted [2]. This behavior is thought to be due to small scale processes - such as matrix diffusion, desorption, and connectivity in the damage region around the large fracture network. In this work, we explore some of these small-scale processes using discrete fracture networks (DFN) and the toolkit dfnWorks [3], the matrix diffusion, size of the damage region, and distribution of free gas between the fracture networks and rock matrix. Individual and combined parameter spaces are explored, and comparisons of the resulting production curves are made to experimental site data from the Haynesville formation [4]. We find that matrix diffusion significantly controls the shape of the tail of the production curve, while the distribution of free gas impacts the relative magnitude of the peak to the tail. The height of the damage region has no effect on the shape of the tail. Understanding the constrains of the parameter space based on site data is the first step in rigorously quantifying the uncertainties coming from these types of systems, which can in turn optimize and improve hydrocarbon recovery. [1] C. McGlade, et. al., (2013) Methods of estimating shale gas resources - comparison, evaluation, and implications, Energy, 59, 116-125 [2] S. Karra, et. al., (2015) Effect of advective flow in fractures and matrix diffusion on natural gas production, Water Resources Research, 51(10), 8646-8657 [3] J.D. Hyman, et

Converting high boiling hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Terrisse, H; DuFour, L

1929-02-12

A process is given for converting high boiling hydrocarbons into low boiling hydrocarbons, characterized in that the high boiling hydrocarbons are heated to 200 to 500/sup 0/C in the presence of ferrous chloride and of such gases as hydrogen, water gas, and the like gases under a pressure of from 5 to 40 kilograms per square centimeter. The desulfurization of the hydrocarbons occurs simultaneously.

Gamma ray spectrometry logs as a hydrocarbon indicator for clastic reservoir rocks in Egypt.

Science.gov (United States)

Al-Alfy, I M; Nabih, M A; Eysa, E A

2013-03-01

Petroleum oil is an important source for the energy in the world. The Gulf of Suez, Nile Delta and South Valley are important regions for studying hydrocarbon potential in Egypt. A thorium normalization technique was applied on the sandstone reservoirs in the three regions to determine the hydrocarbon potentialities zones using the three spectrometric radioactive gamma ray-logs (eU, eTh and K% logs). The conventional well logs (gamma-ray, deep resistivity, shallow resistivity, neutron, density and sonic logs) are analyzed to determine the net pay zones in these wells. Indices derived from thorium normalized spectral logs indicate the hydrocarbon zones in petroleum reservoirs. The results of this technique in the three regions (Gulf of Suez, Nile Delta and South Valley) are in agreement with the results of the conventional well log analyses by ratios of 82%, 78% and 71% respectively. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Hydrocarbons in the Hauptsalz formation of the Gorleben salt dome. Content, distribution and origin

Energy Technology Data Exchange (ETDEWEB)

Pusch, Maximilian; Hammer, Joerg; Ostertag-Henning, Christian [Federal Institute for Geosciences and Natural Resources (BGR), Hannover (Germany)

2015-07-01

In the frame of the geological exploration of the Gorleben salt dome (November 2010 to November 2012) concentrations and compositions of hydrocarbons occuring in the main rock salt (Hauptsalz, Stassfurt series, z2) have been investigated. These exploration works followed former investigations of Gerling et al. (2002) and Bornemann et al. (2008). In order to get fresh, unaltered and representative samples beyond the EDZ (excavation damaged zone) for mineralogical and geochemical analyses, about 45 boreholes have been drilled at the 840 m level of the Gorleben exploration mine. These boreholes have been arranged in equal distances (depending on the mine structure) alongside crosscut 1 west (each 6 m long) and crosscut 1 east (each 9 m long). In addition 20 packer boreholes (10 packer boreholes per crosscut) for pressure build-up recording and hydrocarbon sampling have also been established. Immediately after drilling, core samples from the Hauptsalz for organic geochemical analyses have been retrieved and were dissolved in deionised and degased water. The results of analyses of about 210 samples scattered over all 45 boreholes reveal a total background concentration of hydrocarbons (C{sub 1} to C{sub 40}) of 0,24 mg/kg. 70 samples have concentrations between 1 mg/kg and 50 mg/kg (average 2,66 mg/kg) with 5 outliers up to 442 mg/kg in crosscut 1 west (Hammer et al. 2012, 2013). The drill cores have been investigated and documented by using ultraviolet light (l = 254 nm) in respect of visible indications of the existence of fluorescing aromatic hydrocarbons. Analyses revealed a high level of heterogeneous hydrocarbon distribution in the shape of isolated, irregular streaks, clusters, clouds and occasionally layers mainly located in recrystallized zones of the Hauptsalz. Thin sections and thick sections showed that hydrocarbons in z2HS1 (Knaeuelsalz) and z2HS2 (Streifensalz) samples are either located as black to brownish dendritical fluid inclusions alongside the grain

Evaluation of hydrocarbon potential, Task 8

International Nuclear Information System (INIS)

Cashman, P.H.; Trexler, J.H. Jr.

1993-01-01

Task 8 is responsible for assessing the hydrocarbon potential of the Yucca Mountain vicinity. Our main focus is source rock stratigraphy in the Nevada Test Site (NTS) area in southern Nevada. In order to reconstruct the Paleozoic stratigraphy, we are also studying the geometry and kinematics of deformation at NTS. A thorough understanding of the structure will also be essential to predicting the nature of the Late Paleozoic rocks under Yucca Mountain. Our stratigraphic studies continue to support the interpretation that rocks mapped as the open-quotes Eleana Formationclose quotes are in fact parts of two different Mississippian units. We are now provisionally limiting the name open-quotes Eleana Formationclose quotes to the rocks that make up the Eleana Range - i.e., the rocks that we have been calling open-quotes western Eleanaclose quotes. The mudstone section (which we have until now called open-quotes eastern Eleanaclose quotes) we are provisionally calling the open-quotes Chainman Shaleclose quotes, in keeping with regional lithostratigraphic nomenclature. We continue to work out the internal stratigraphies and basin histories of both units; XRD (r-ray diffraction) determinations of clay mineralogy are an addition to our understanding of the Chainman. The basin histories place important constraints on regional paleogeographic and tectonic reconstructions. This year we have hired a consulting petroleum geologist for two jobs: (1) to review drillhole data from southern Nevada on file at NBMG and make recommendations about more detailed study of any interesting drillholes; and (2) to log the UE17e core (in the Chainman) and evaluate source rock potential. The results of these studies have been incorporated into this report, and the consultant's reports

Modelling Poly-Aromatic Hydrocarbons "online" with the GEOS-Chem Europe and Asia regional models.

Science.gov (United States)

Ivatt, P.; Evans, M. J.

2017-12-01

Poly-Aromatic Hydrocarbons (PAHs) are carcinogens and so are restricted by international treaties. PAHs are mainly emitted into the atmosphere by domestic (heating and cooking), natural (forest fires burning), as well as some industrial processes (coke ovens). PAHs partition between the gas and particle phase (notably carbonaceous particles) based on their volatility. In recent years, interest has turned to the possible health effects of their oxidation products (both nitrogenated and oxygenated) as it has been suggested that these oxidation products may be even more carcinogenic than the parent PAHs. To increase our understanding of the processes controlling the regional concentrations of PAHs and their oxidation products an "online" PAH model has been developed within the GEOS-Chem framework. This provides for the representation of the coupled aerosol/gas phase chemistry of the parent PAH and its secondary oxidation products. Benzo[a]pyrene is used as an exemplar but the methodology is flexible and the approach can be used for any PAH species. Comparisons are made with observations and the sources of variability discussed.

In-core Instrument Subcritical Verification (INCISV) - Core Design Verification Method - 358

International Nuclear Information System (INIS)

Prible, M.C.; Heibel, M.D.; Conner, S.L.; Sebastiani, P.J.; Kistler, D.P.

2010-01-01

According to the standard on reload startup physics testing, ANSI/ANS 19.6.1, a plant must verify that the constructed core behaves sufficiently close to the designed core to confirm that the various safety analyses bound the actual behavior of the plant. A large portion of this verification must occur before the reactor operates at power. The INCISV Core Design Verification Method uses the unique characteristics of a Westinghouse Electric Company fixed in-core self powered detector design to perform core design verification after a core reload before power operation. A Vanadium self powered detector that spans the length of the active fuel region is capable of confirming the required core characteristics prior to power ascension; reactivity balance, shutdown margin, temperature coefficient and power distribution. Using a detector element that spans the length of the active fuel region inside the core provides a signal of total integrated flux. Measuring the integrated flux distributions and changes at various rodded conditions and plant temperatures, and comparing them to predicted flux levels, validates all core necessary core design characteristics. INCISV eliminates the dependence on various corrections and assumptions between the ex-core detectors and the core for traditional physics testing programs. This program also eliminates the need for special rod maneuvers which are infrequently performed by plant operators during typical core design verification testing and allows for safer startup activities. (authors)

Sources and Deposition of Polycyclic Aromatic Hydrocarbons to Western U.S. National Parks

Science.gov (United States)

USENKO, SASCHA; MASSEY SIMONICH, STACI L.; HAGEMAN, KIMBERLY J.; SCHRLAU, JILL E.; GEISER, LINDA; CAMPBELL, DON H.; APPLEBY, PETER G.; LANDERS, DIXON H.

2010-01-01

Seasonal snowpack, lichens, and lake sediment cores were collected from fourteen lake catchments in eight western U.S. National Parks and analyzed for sixteen polycyclic aromatic hydrocarbons (PAHs) in order to determine their current and historical deposition, as well as to identify their potential sources. Seasonal snowpack was measured to determine the current wintertime atmospheric PAH deposition; lichens were measured to determine the long-term, year around deposition; and the temporal PAH deposition trends were reconstructed using lake sediment cores dated using 210Pb and 137Cs. The fourteen remote lake catchments ranged from low-latitude catchments (36.6° N) at high elevation (2900 masl) in Sequoia National Park, CA to high-latitude catchments (68.4° N) at low elevation (427 masl) in the Alaskan Arctic. Over 75% of the catchments demonstrated statistically significant temporal trends in ΣPAH sediment flux, depending on catchment proximity to source regions and topographic barriers. The ΣPAH concentrations and fluxes in seasonal snowpack, lichens, and surficial sediment were 3.6 to 60,000 times greater in the Snyder Lake catchment of Glacier National Park than the other 13 lake catchments. The PAH ratios measured in snow, lichen, and sediment were used to identify a local aluminum smelter as a major source of PAHs to the Snyder Lake catchment. These results suggest that topographic barriers influence the atmospheric transport and deposition of PAHs in high-elevation ecosystems and that PAH sources to these national park ecosystems range from local point sources to diffuse regional and global sources. PMID:20465303

Formation evaluation in Devonian shale through application of new core and log analysis methods

International Nuclear Information System (INIS)

Luffel, D.L.; Guidry, F.K.

1990-01-01

In the Devonian shale of the Appalachian Basin all porosity in excess of about 2.5 percent is generally occupied by free hydrocarbons, which is mostly gas, based on results of new core and log analysis methods. In this study, sponsored by the Gas Research Institute, reservoir porosities averaged about 5 percent and free gas content averaged about 2 percent by bulk volume, based on analyses on 519 feet of conventional core in four wells. In this source-rich Devonian shale, which also provides the reservoir storage, the rock everywhere appears to be at connate, or irreducible, water saturation corresponding to two or three percent of bulk volume. This became evident when applying the new core and log analysis methods, along with a new plotting method relating bulk volume of pore fluids to porosity. This plotting method has proved to be a valuable tool: it provides useful insight on the fluid distribution present in the reservoir, it provides a clear idea of porosity required to store free hydrocarbons, it leads to a method of linking formation factor to porosity, and it provides a good quality control method to monitor core and log analysis results. In the Devonian shale an important part of the formation evaluation is to determine the amount of kerogen, since this appears as hydrocarbon-filled porosity to conventional logs. In this study Total Organic Carbon and pyrolysis analyses were made on 93 core samples from four wells. Based on these data a new method was used to drive volumetric kerogen and free oil content, and kerogen was found to range up to 26 percent by volume. A good correlation was subsequently developed to derive kerogen from the uranium response of the spectral gamma ray log. Another important result of this study is the measurement of formation water salinity directly on core samples. Results on 50 measurements in the four study wells ranged from 19,000 to 220,000 ppm NaCl

Production of hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Day, D T; Day, R E

1920-04-27

A process is disclosed of converting hydro-carbon oils having high boiling points to hydro-carbon oils having low boiling points, which process comprises adding the oil to be treated to a mass of hydro-carbon oil bearing shale, passing the shale with the oil through a conveyor retort and subjecting the material while in the retort to a heat treatment involving a temperature of at least 500/sup 0/F.

Equilibrium passive sampling as a tool to study polycyclic aromatic hydrocarbons in Baltic Sea sediment pore-water systems

DEFF Research Database (Denmark)

Lang, Susann-Cathrin; Hursthouse, Andrew; Mayer, Philipp

2015-01-01

Solid Phase Microextraction (SPME) was applied to provide the first large scale dataset of freely dissolved concentrations for 9 polycyclic aromatic hydrocarbons (PAHs) in Baltic Sea sediment cores. Polydimethylsiloxane (PDMS) coated glass fibers were used for ex-situ equilibrium sampling followed...

FBR type reactor core

International Nuclear Information System (INIS)

Tamiya, Tadashi; Kawashima, Katsuyuki; Fujimura, Koji; Murakami, Tomoko.

1995-01-01

Neutron reflectors are disposed at the periphery of a reactor core fuel region and a blanket region, and a neutron shielding region is disposed at the periphery of them. The neutron reflector has a hollow duct structure having a sealed upper portion, a lower portion opened to cooling water, in which a gas and coolants separately sealed in the inside thereof. A driving pressure of a primary recycling pump is lowered upon reduction of coolant flow rate, then the liquid level of coolants in the neutron reflector is lowered due to imbalance between the driving pressure and a gas pressure, so that coolants having an effect as a reflector are eliminated from the outer circumference of the reactor core. Therefore, the amount of neutrons leaking from the reactor core is increased, and negative reactivity is charged to the reactor core. The negative reactivity of the neutron reflector is made greater than a power compensation reactivity. Since this enables reactor scram by using an inherent performance of the reactor core, the reactor core safety of an LMFBR-type reactor can be improved. (I.N.)

Adsorption of volatile hydrocarbons in iron polysulfide chalcogels

KAUST Repository

Ahmed, Ejaz; Rothenberger, Alexander

2014-01-01

are found in micro (below 2 nm), meso (2-50 nm), and macro (above 50 nm) porous regions. These chalcogels possess optical bandgaps in the range of 1.55-2.70 eV. These aerogels have been studied for the adsorption of volatile hydrocarbons and gases. A much

Polycyclic aromatic hydrocarbons in soils from the Tibetan Plateau, China: distribution and influence of environmental factors.

Science.gov (United States)

Wang, Shuang; Ni, Hong-Gang; Sun, Jian-Lin; Jing, Xin; He, Jin-Sheng; Zeng, Hui

2013-03-01

Thirty four sampling sites along an elevation transect in the Tibetan Plateau region were chosen. Soil cores were divided into several layers and a total of 175 horizon soil samples were collected from July to September 2011, for determination of polycyclic aromatic hydrocarbons (PAHs). The measured PAHs concentration in surface soils was 56.26 ± 45.84 ng g(-1), and the low molecular weight PAHs (2-3 rings) predominated, accounting for 48% and 35%. We analyzed the spatial (altitudinal and vertical) distribution of PAHs in soil, and explored the influence of related environmental factors. Total organic carbon (TOC) showed a controlling influence on the distribution of PAHs. PAH concentrations declined with soil depth, and the composition patterns of PAHs along soil depth indicated that the heavy PAHs tended to remain in the upper layers (0-10 cm), while the light fractions were transported downward more easily. PAHs inventories (8.77-57.92 mg m(-2)) for soil cores increased with mean annual precipitation, while the topsoil concentrations decreased with it. This implies that an increase in precipitation could transfer more PAHs from the atmosphere to the soil and further transport PAHs from the topsoil to deeper layers.

Solo Mycoremediation Impacted by Waste Hydrocarbons

Directory of Open Access Journals (Sweden)

Franklin Santos Freire

2015-06-01

Full Text Available Oil and its derivatives are the principal means of energy generation for vehicles that transport raw materials and goods produced in developed and developing regions accentuating the risk of accidents by spills in stockpiling, transport, use or discarding. The contamination by total hydrocarbons suggests the elevated propension to mutations and to the formation of carcinogenic tumors, as a consequence of the exposure to human contamination by these products. This work had as aims: a To investigate, in a laboratorial scale, the degrading capacity of autochthonous microbiota in the presence of differing concentrations of hydrocarbons (0%, 2,5%, 5% e 7,5%; b To isolate fungi tolerant to the contaminant; c To quantify and analyze the biodegradation capacity of soil through the microbial biomass and metabolic quotient; and d To set, in laboratory, ideal conditions of biodegradation of the xenobiotic compound. Some parameters of microbial activity have been evaluated, such as: biological (Carbon of microbial biomass, CO2 , qCO2 emission, and fungi growth, chemical (pH, electrical conductivity –EC –, analysis of fertility and total hydrocarbons and physical (physical composition of the soil for analysis and comparisons. The obtained results suggest that the adding of 5% of waste oil in the ground provided ideal condition for the biodegradation of he   contaminant in the environment. From the evaluated parameters, the emission of CO2 and microbial C were considered more indicative of changes in soil microbial activity subject to the addition of hydrocarbons, confirming the possibility of microremediation use.

Reactor core in FBR type reactor

International Nuclear Information System (INIS)

Masumi, Ryoji; Kawashima, Katsuyuki; Kurihara, Kunitoshi.

1989-01-01

In a reactor core in FBR type reactors, a portion of homogenous fuels constituting the homogenous reactor core is replaced with multi-region fuels in which the enrichment degree of fissile materials is lower nearer to the axial center. This enables to condition the composition such that a reactor core having neutron flux distribution either of a homogenous reactor core or a heterogenous reactor core has substantially identical reactivity. Accordingly, in the transfer from the homogenous reactor core to the axially heterogenous reactor core, the average reactivity in the reactor core is substantially equal in each of the cycles. Further, by replacing a portion of the homogenous fuels with a multi-region fuels, thereby increasing the heat generation near the axial center, it is possiable to reduce the linear power output in the regions above and below thereof and, in addition, to improve the thermal margin in the reactor core. (T.M.)

A New Global Open Source Marine Hydrocarbon Emission Site Database

Science.gov (United States)

Onyia, E., Jr.; Wood, W. T.; Barnard, A.; Dada, T.; Qazzaz, M.; Lee, T. R.; Herrera, E.; Sager, W.

2017-12-01

Hydrocarbon emission sites (e.g. seeps) discharge large volumes of fluids and gases into the oceans that are not only important for biogeochemical budgets, but also support abundant chemosynthetic communities. Documenting the locations of modern emissions is a first step towards understanding and monitoring how they affect the global state of the seafloor and oceans. Currently, no global open source (i.e. non-proprietry) detailed maps of emissions sites are available. As a solution, we have created a database that is housed within an Excel spreadsheet and use the latest versions of Earthpoint and Google Earth for position coordinate conversions and data mapping, respectively. To date, approximately 1,000 data points have been collected from referenceable sources across the globe, and we are continualy expanding the dataset. Due to the variety of spatial extents encountered, to identify each site we used two different methods: 1) point (x, y, z) locations for individual sites and; 2) delineation of areas where sites are clustered. Certain well-known areas, such as the Gulf of Mexico and the Mediterranean Sea, have a greater abundance of information; whereas significantly less information is available in other regions due to the absence of emission sites, lack of data, or because the existing data is proprietary. Although the geographical extent of the data is currently restricted to regions where the most data is publicly available, as the database matures, we expect to have more complete coverage of the world's oceans. This database is an information resource that consolidates and organizes the existing literature on hydrocarbons released into the marine environment, thereby providing a comprehensive reference for future work. We expect that the availability of seafloor hydrocarbon emission maps will benefit scientific understanding of hydrocarbon rich areas as well as potentially aiding hydrocarbon exploration and environmental impact assessements.

L-cysteine-capped core/shell/shell quantum dot-graphene oxide nanocomposite fluorescence probe for polycyclic aromatic hydrocarbon detection.

Science.gov (United States)

Adegoke, Oluwasesan; Forbes, Patricia B C

2016-01-01

Environmental pollutants, such as the polycyclic aromatic hydrocarbons (PAHs), become widely distributed in the environment after emission from a range of sources, and they have potential biological effects, including toxicity and carcinogenity. In this work, we have demonstrated the analytical potential of a covalently linked L-cysteine-capped CdSeTe/ZnSe/ZnS core/shell/shell quantum dot (QD)-graphene oxide (GO) nanocomposite fluorescence probe to detect PAH compounds in aqueous solution. Water-soluble L-cysteine-capped CdSeTe/ZnSe/ZnS QDs were synthesized for the first time and were covalently bonded to GO. The fluorescence of the QD-GO nanocomposite was enhanced relative to the unconjugated QDs. Various techniques including TEM, SEM, HRSEM, XRD, Raman, FT-IR, UV/vis and fluorescence spectrophotometry were employed to characterize both the QDs and the QD-GO nanocomposite. Four commonly found priority PAH analytes namely; phenanthrene (Phe), anthracene (Ant), pyrene (Py) and naphthalene (Naph), were tested and it was found that each of the PAH analytes enhanced the fluorescence of the QD-GO probe. Phe was selected for further studies as the PL enhancement was significantly greater for this PAH. A limit of detection (LOD) of 0.19 µg/L was obtained for Phe under optimum conditions, whilst the LOD of Ant, Py and Naph were estimated to be ~0.26 µg/L. The fluorescence detection mechanism is proposed. Copyright © 2015 Elsevier B.V. All rights reserved.

Performance of a Throttle Cycle Refrigerator with Nitrogen-Hydrocarbon and Argon-Hydrocarbon Mixtures

Science.gov (United States)

Venkatarathnam, G.; Senthil Kumar, P.; Srinivasa Murthy, S.

2004-06-01

Throttle cycle refrigerators are a class of vapor compression refrigerators that can provide refrigeration at cryogenic temperatures and operate with refrigerant mixtures. The performance of our prototype refrigerators with nitrogen-hydrocarbon, nitrogen-hydrocarbon-helium and argon-hydrocarbon refrigerant mixtures is presented in this paper.

Petroleum hydrocarbons and polycyclic aromatic hydrocarbons (PAHs) in Hong Kong marine sediments

International Nuclear Information System (INIS)

Zheng, G.J.; Richardson, B.J.

1999-01-01

A total of 20 surficial sediment samples, obtained from Hong Kong coastal waters, were analysed for petroleum hydrocarbons (PHCs) and a suite of 15 polycyclic aromatic hydrocarbons (PAHs). The results indicate that Hong Kong coastal sediments are often seriously polluted with petroleum related hydrocarbons. This is especially so in heavily urbanised or industrialized localities, such as Kowloon Bay (Victoria Harbour), Tsing Yi North and Tolo Harbour. Petroleum hydrocarbon pollutants in marine sediments are believed to be mainly derived from the transportation of oil, shipping activities, spillages, and industrial, stormwater and waste wastewater discharge. The ratio of unresolved complex mixture (UCM) to n-alkanes, carbon preference index (CPI), and n-C 16 values indicate that the main contribution to petroleum hydrocarbon contamination is via oil and its products. Pollutant sources appear to be stable and continuing when compared with previous data. (author)

Purifying hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Demoulins, H D; Garner, F H

1923-02-07

Hydrocarbon distillates, including natural gases and vapors produced by cracking hydrocarbon oils, are desulfurized etc. by treating the vapor with an aqueous alkaline solution of an oxidizing agent. The hydrocarbons may be previously purified by sulfuric acid. In examples aqueous solutions of sodium or calcium hydrochlorite containing 1.5 to 5.0 grams per liter of available chlorine and sufficient alkali to give an excess of 0.1 percent in the spent reagent are preheated to the temperature of the vapor, and either sprayed or atomized into the vapors near the outlet of the dephlegmator or fractionating tower, or passed in countercurrent to the vapors through one or a series of scrubbers.

Abiogenic origin of petroleum hydrocarbons: Need to rethink exploration strategies

Digital Repository Service at National Institute of Oceanography (India)

Paropkari, A.L.

-depletion of petroleum deposits since long. Considering these strong evidences, it is suggested to explore the onshore and offshore regions characterized by faults, gas escape features, mud diapirs and mud volcanoes for detailed abiogenic hydrocarbon exploration...

Positron induced scattering cross sections for hydrocarbons relevant to plasma

Science.gov (United States)

Singh, Suvam; Antony, Bobby

2018-05-01

This article explores positron scattering cross sections by simple hydrocarbons such as ethane, ethene, ethyne, propane, and propyne. Chemical erosion processes occurring on the surface due to plasma-wall interactions are an abundant source of hydrocarbon molecules which contaminate the hydrogenic plasma. These hydrocarbons play an important role in the edge plasma region of Tokamak and ITER. In addition to this, they are also one of the major components in the planetary atmospheres and astrophysical mediums. The present work focuses on calculation of different positron impact interactions with simple hydrocarbons in terms of the total cross section (Qtot), elastic cross section (Qel), direct ionization cross section (Qion), positronium formation cross section (Qps), and total ionization cross section (Qtion). Knowing that the positron-plasma study is one of the trending fields, the calculated data have diverse plasma and astrophysical modeling applications. A comprehensive study of Qtot has been provided where the inelastic cross sections have been reported for the first time. Comparisons are made with those available from the literature, and a good agreement is obtained with the measurements.

Early events following radiolytic and photogeneration of radical cations in hydrocarbons

International Nuclear Information System (INIS)

Werst, D.W.; Trifunac, A.D.

1992-01-01

Real-time studies in hydrocarbons have revealed a richness of chemistry involving the initial ionic species produced in radiolysis and photoionization. A modified radical cation mechanism patterned after the core mechanism for alkane radiolysis-formation of radical cations and their disappearance via ion-molecule reactions - is capable of explaining a wide range of observations in high-energy photochemistry, and thus unifies two high-energy regimes. Fundamental studies of radical cations suggest strategies for mitigating radiation effects in materials

Degradation and utilization of polycyclic aromatic hydrocarbons by indigenous soil bacteria

International Nuclear Information System (INIS)

Stetzenbach, L.D.A.

1986-01-01

The persistence of industrially derived polycyclic aromatic hydrocarbons in the subsurface may be significantly affected by the metabolism of soil bacteria. This study was conducted to determine the ability of indigenous soil bacteria to decrease the concentration of four polycyclic aromatic hydrocarbons (naphthalene, fluorene, anthracene, and pyrene) and to utilize the compounds as a substrate for growth. Soil cores from petroleum contaminated and noncontaminated sites contained 10 5 -10 7 viable microorganisms per gram dryweight of soil. Gram negative rod-shaped bacteria predominated. Decreases in the concentration of the four polycyclic aromatic hydrocarbons were observed during incubation with bacterial isolates in aqueous suspension by the use of high performance liquid chromatography. Corresponding increases in bacterial numbers indicated utilization of the compounds as a carbon source. Soil samples from the contaminated sites contained greater numbers of bacteria utilizing anthracene and pyrene than soil samples from uncontaminated sites. Degradation rates of the four polycyclic aromatic hydrocarbons were related to the compound, its concentration, and the bacterium. Biodegradation of pyrene was positively correlated with the presence of oxygen. Pyrene was biodegraded by an Acinetobacter sp. under aerobic conditions but not under anaerobic or microaerophilic conditions. Studies with radiolabeled 14 C-anthracene demonstrated utilization of the labeled carbon as a source of carbon by viable bacterial cells in aqueous suspension. Incorporation of 14 C into cellular biomass however was not observed during incubation of 14 C-anthracene in soil

Digital Core Modelling for Clastic Oil and Gas Reservoir

Science.gov (United States)

Belozerov, I.; Berezovsky, V.; Gubaydullin, M.; Yur’ev, A.

2018-05-01

"Digital core" is a multi-purpose tool for solving a variety of tasks in the field of geological exploration and production of hydrocarbons at various stages, designed to improve the accuracy of geological study of subsurface resources, the efficiency of reproduction and use of mineral resources, as well as applying the results obtained in production practice. The actuality of the development of the "Digital core" software is that even a partial replacement of natural laboratory experiments with mathematical modelling can be used in the operative calculation of reserves in exploratory drilling, as well as in the absence of core material from wells. Or impossibility of its research by existing laboratory methods (weakly cemented, loose, etc. rocks). 3D-reconstruction of the core microstructure can be considered as a cheap and least time-consuming method for obtaining petrophysical information about the main filtration-capacitive properties and fluid motion in reservoir rocks.

Influence of the core-hole effect on optical properties of magnesium oxide (MgO) near the Mg L-edge region.

Science.gov (United States)

Sinha, Mangalika; Modi, Mohammed H; Ghosh, Haranath; Yadav, P K; Gupta, R K

2018-05-01

The influence of the core-hole effect on optical properties of magnesium oxide (MgO) is established through experimental determination of optical constants and first-principles density functional theory studies. Optical constants (δ and β) of MgO thin film are measured in the spectral region 40-300 eV using reflectance spectroscopy techniques at the Indus-1 synchrotron radiation source. The obtained optical constants show strong core exciton features near the Mg L-edge region, causing significant mismatch with Henke's tabulated values. On comparing the experimentally obtained optical constants with Henke's tabulated values, an edge shift of ∼3.0 eV is also observed. Distinct evidence of effects of core exciton on optical constants (δ and β) in the near Mg L-edge absorption spectra are confirmed through first-principles simulations.

Regional modelling of polycyclic aromatic hydrocarbons: WRF-Chem-PAH model development and East Asia case studies

Science.gov (United States)

Mu, Qing; Lammel, Gerhard; Gencarelli, Christian N.; Hedgecock, Ian M.; Chen, Ying; Přibylová, Petra; Teich, Monique; Zhang, Yuxuan; Zheng, Guangjie; van Pinxteren, Dominik; Zhang, Qiang; Herrmann, Hartmut; Shiraiwa, Manabu; Spichtinger, Peter; Su, Hang; Pöschl, Ulrich; Cheng, Yafang

2017-10-01

Polycyclic aromatic hydrocarbons (PAHs) are hazardous pollutants, with increasing emissions in pace with economic development in East Asia, but their distribution and fate in the atmosphere are not yet well understood. We extended the regional atmospheric chemistry model WRF-Chem (Weather Research Forecast model with Chemistry module) to comprehensively study the atmospheric distribution and the fate of low-concentration, slowly degrading semivolatile compounds. The WRF-Chem-PAH model reflects the state-of-the-art understanding of current PAHs studies with several new or updated features. It was applied for PAHs covering a wide range of volatility and hydrophobicity, i.e. phenanthrene, chrysene and benzo[a]pyrene, in East Asia. Temporally highly resolved PAH concentrations and particulate mass fractions were evaluated against observations. The WRF-Chem-PAH model is able to reasonably well simulate the concentration levels and particulate mass fractions of PAHs near the sources and at a remote outflow region of East Asia, in high spatial and temporal resolutions. Sensitivity study shows that the heterogeneous reaction with ozone and the homogeneous reaction with the nitrate radical significantly influence the fate and distributions of PAHs. The methods to implement new species and to correct the transport problems can be applied to other newly implemented species in WRF-Chem.

Linking biochemical perturbations in tissues of the African catfish to the presence of polycyclic aromatic hydrocarbons in Ovia River, Niger Delta region

International Nuclear Information System (INIS)

Obinaju, Blessing E.; Graf, Carola; Halsall, Crispin; Martin, Francis L.

2015-01-01

Petroleum hydrocarbons including polycyclic aromatic hydrocarbons (PAHs) are a pollution issue in the Niger Delta region due to oil industry activities. PAHs were measured in the water column of the Ovia River with concentrations ranging from 0.1 to 1055.6 ng L −1 . Attenuated total reflection Fourier-transform infrared (ATR-FTIR) spectroscopy detected alterations in tissues of the African catfish (Heterobranchus bidorsalis) from the region showed varying degrees of statistically significant (P < 0.0001, P < 0.001, P < 0.05) changes to absorption band areas and shifts in centroid positions of peaks. Alteration patterns were similar to those induced by benzo[a]pyrene in MCF-7 cells. These findings have potential health implications for resident local communities as H. bidorsalis constitutes a key nutritional source. The study provides supporting evidence for the sensitivity of infrared spectroscopy in environmental studies and supports their potential application in biomonitoring. - Highlights: • PAHs measured in the water column of the Ovia River (Nigeria). • ATR-FTIR spectroscopy detects alterations in tissues of the African catfish (Heterobranchus bidorsalis). • Spectral alteration similar to those induced by benzo[a]pyrene in MCF-7 cells. • Alterations in tissues of African catfish (H. bidorsalis) a function of exposure to waterborne PAHs. • Vibrational spectroscopy techniques detect minimal changes induced by environmental exposures. - Spatial and temporal analyses by biospectroscopy techniques of African catfish (Heterobranchus bidorsalis) tissues suggest that detected alterations can reflect fluctuating exposures to PAHs

EXTERNALLY HEATED PROTOSTELLAR CORES IN THE OPHIUCHUS STAR-FORMING REGION

Energy Technology Data Exchange (ETDEWEB)

Lindberg, Johan E.; Charnley, Steven B.; Cordiner, Martin A. [NASA Goddard Space Flight Center, Astrochemistry Laboratory, Mail Code 691, 8800 Greenbelt Road, Greenbelt, MD 20771 (United States); Jørgensen, Jes K.; Bjerkeli, Per, E-mail: johan.lindberg@nasa.gov [Centre for Star and Planet Formation, Niels Bohr Institute and Natural History Museum of Denmark, University of Copenhagen, Øster Voldgade 5-7, DK-1350 Copenhagen K (Denmark)

2017-01-20

We present APEX 218 GHz observations of molecular emission in a complete sample of embedded protostars in the Ophiuchus star-forming region. To study the physical properties of the cores, we calculate H{sub 2}CO and c -C{sub 3}H{sub 2} rotational temperatures, both of which are good tracers of the kinetic temperature of the molecular gas. We find that the H{sub 2}CO temperatures range between 16 K and 124 K, with the highest H{sub 2}CO temperatures toward the hot corino source IRAS 16293-2422 (69–124 K) and the sources in the ρ Oph A cloud (23–49 K) located close to the luminous Herbig Be star S1, which externally irradiates the ρ Oph A cores. On the other hand, the c -C{sub 3}H{sub 2} rotational temperature is consistently low (7–17 K) in all sources. Our results indicate that the c -C{sub 3}H{sub 2} emission is primarily tracing more shielded parts of the envelope whereas the H{sub 2}CO emission (at the angular scale of the APEX beam; 3600 au in Ophiuchus) mainly traces the outer irradiated envelopes, apart from in IRAS 16293-2422, where the hot corino emission dominates. In some sources, a secondary velocity component is also seen, possibly tracing the molecular outflow.

How cores grow by pebble accretion. I. Direct core growth

Science.gov (United States)

Brouwers, M. G.; Vazan, A.; Ormel, C. W.

2018-03-01

Context. Planet formation by pebble accretion is an alternative to planetesimal-driven core accretion. In this scenario, planets grow by the accretion of cm- to m-sized pebbles instead of km-sized planetesimals. One of the main differences with planetesimal-driven core accretion is the increased thermal ablation experienced by pebbles. This can provide early enrichment to the planet's envelope, which influences its subsequent evolution and changes the process of core growth. Aims: We aim to predict core masses and envelope compositions of planets that form by pebble accretion and compare mass deposition of pebbles to planetesimals. Specifically, we calculate the core mass where pebbles completely evaporate and are absorbed before reaching the core, which signifies the end of direct core growth. Methods: We model the early growth of a protoplanet by calculating the structure of its envelope, taking into account the fate of impacting pebbles or planetesimals. The region where high-Z material can exist in vapor form is determined by the temperature-dependent vapor pressure. We include enrichment effects by locally modifying the mean molecular weight of the envelope. Results: In the pebble case, three phases of core growth can be identified. In the first phase (Mcore mixes outwards, slowing core growth. In the third phase (Mcore > 0.5M⊕), the high-Z inner region expands outwards, absorbing an increasing fraction of the ablated material as vapor. Rainout ends before the core mass reaches 0.6 M⊕, terminating direct core growth. In the case of icy H2O pebbles, this happens before 0.1 M⊕. Conclusions: Our results indicate that pebble accretion can directly form rocky cores up to only 0.6 M⊕, and is unable to form similarly sized icy cores. Subsequent core growth can proceed indirectly when the planet cools, provided it is able to retain its high-Z material.

Novel techniques for characterization of hydrocarbon emission sources in the Barnett Shale

Science.gov (United States)

Nathan, Brian Joseph

Changes in ambient atmospheric hydrocarbon concentrations can have both short-term and long-term effects on the atmosphere and on human health. Thus, accurate characterization of emissions sources is critically important. The recent boom in shale gas production has led to an increase in hydrocarbon emissions from associated processes, though the exact extent is uncertain. As an original quantification technique, a model airplane equipped with a specially-designed, open-path methane sensor was flown multiple times over a natural gas compressor station in the Barnett Shale in October 2013. A linear optimization was introduced to a standard Gaussian plume model in an effort to determine the most probable emission rate coming from the station. This is shown to be a suitable approach given an ideal source with a single, central plume. Separately, an analysis was performed to characterize the nonmethane hydrocarbons in the Barnett during the same period. Starting with ambient hourly concentration measurements of forty-six hydrocarbon species, Lagrangian air parcel trajectories were implemented in a meteorological model to extend the resolution of these measurements and achieve domain-fillings of the region for the period of interest. A self-organizing map (a type of unsupervised classification) was then utilized to reduce the dimensionality of the total multivariate set of grids into characteristic one-dimensional signatures. By also introducing a self-organizing map classification of the contemporary wind measurements, the spatial hydrocarbon characterizations are analyzed for periods with similar wind conditions. The accuracy of the classification is verified through assessment of observed spatial mixing ratio enhancements of key species, through site-comparisons with a related long-term study, and through a random forest analysis (an ensemble learning method of supervised classification) to determine the most important species for defining key classes. The hydrocarbon

A sedimentological approach to refining reservoir architecture in a mature hydrocarbon province: the Brent Province, UK North Sea

Energy Technology Data Exchange (ETDEWEB)

Hampson, G.J.; Sixsmith, P.J.; Johnson, H.D. [Imperial College, London (United Kingdom). Dept. of Earth Science and Engineering

2004-04-01

Improved reservoir characterisation in the mature Brent Province of the North Sea, aimed at maximising both in-field and near-field hydrocarbon potential, requires a clearer understanding of sub-seismic stratigraphy and facies distributions. In this context, we present a regional, high-resolution sequence stratigraphic framework for the Brent Group, UK North Sea based on extensive sedimentological re-interpretation of core and wireline-log data, combined with palynostratigraphy and published literature. This framework is used to place individual reservoirs in an appropriate regional context, thus resulting in the identification of subtle sedimentological and tectono-stratigraphic features of reservoir architecture that have been previously overlooked. We emphasise the following insights gained from our regional, high-resolution sequence stratigraphic synthesis: (1) improved definition of temporal and spatial trends in deposition both within and between individual reservoirs, (2) development of regionally consistent, predictive sedimentological models for two enigmatic reservoir intervals (the Broom and Tarbert Formations), and (3) recognition of subtle local tectono-stratigraphic controls on reservoir architecture, and their links to the regional, Middle Jurassic structural evolution of the northern North Sea. We discuss the potential applications of these insights to the identification of additional exploration potential and to improved ultimate recovery. (author)

Isolation and Characterization of Hydrocarbon-Degrading Yeast Strains from Petroleum Contaminated Industrial Wastewater

Science.gov (United States)

Gargouri, Boutheina; Mhiri, Najla; Karray, Fatma; Aloui, Fathi; Sayadi, Sami

2015-01-01

Two yeast strains are enriched and isolated from industrial refinery wastewater. These strains were observed for their ability to utilize several classes of petroleum hydrocarbons substrates, such as n-alkanes and aromatic hydrocarbons as a sole carbon source. Phylogenetic analysis based on the D1/D2 variable domain and the ITS-region sequences indicated that strains HC1 and HC4 were members of the genera Candida and Trichosporon, respectively. The mechanism of hydrocarbon uptaking by yeast, Candida, and Trichosporon has been studied by means of the kinetic analysis of hydrocarbons-degrading yeasts growth and substrate assimilation. Biodegradation capacity and biomass quantity were daily measured during twelve days by gravimetric analysis and gas chromatography coupled with mass spectrometry techniques. Removal of n-alkanes indicated a strong ability of hydrocarbon biodegradation by the isolated yeast strains. These two strains grew on long-chain n-alkane, diesel oil, and crude oil but failed to grow on short-chain n-alkane and aromatic hydrocarbons. Growth measurement attributes of the isolates, using n-hexadecane, diesel oil, and crude oil as substrates, showed that strain HC1 had better degradation for hydrocarbon substrates than strain HC4. In conclusion, these yeast strains can be useful for the bioremediation process and decreasing petroleum pollution in wastewater contaminated with petroleum hydrocarbons. PMID:26339653

Isolation and Characterization of Hydrocarbon-Degrading Yeast Strains from Petroleum Contaminated Industrial Wastewater

Directory of Open Access Journals (Sweden)

Boutheina Gargouri

2015-01-01

Full Text Available Two yeast strains are enriched and isolated from industrial refinery wastewater. These strains were observed for their ability to utilize several classes of petroleum hydrocarbons substrates, such as n-alkanes and aromatic hydrocarbons as a sole carbon source. Phylogenetic analysis based on the D1/D2 variable domain and the ITS-region sequences indicated that strains HC1 and HC4 were members of the genera Candida and Trichosporon, respectively. The mechanism of hydrocarbon uptaking by yeast, Candida, and Trichosporon has been studied by means of the kinetic analysis of hydrocarbons-degrading yeasts growth and substrate assimilation. Biodegradation capacity and biomass quantity were daily measured during twelve days by gravimetric analysis and gas chromatography coupled with mass spectrometry techniques. Removal of n-alkanes indicated a strong ability of hydrocarbon biodegradation by the isolated yeast strains. These two strains grew on long-chain n-alkane, diesel oil, and crude oil but failed to grow on short-chain n-alkane and aromatic hydrocarbons. Growth measurement attributes of the isolates, using n-hexadecane, diesel oil, and crude oil as substrates, showed that strain HC1 had better degradation for hydrocarbon substrates than strain HC4. In conclusion, these yeast strains can be useful for the bioremediation process and decreasing petroleum pollution in wastewater contaminated with petroleum hydrocarbons.

Black tattoos entail substantial uptake of genotoxicpolycyclic aromatic hydrocarbons (PAH) in human skin and regional lymph nodes.

Science.gov (United States)

Lehner, Karin; Santarelli, Francesco; Vasold, Rudolf; Penning, Randolph; Sidoroff, Alexis; König, Burkhard; Landthaler, Michael; Bäumler, Wolfgang

2014-01-01

Hundreds of millions of people worldwide have tattoos, which predominantly contain black inks consisting of soot products like Carbon Black or polycyclic aromatic hydrocarbons (PAH). We recently found up to 200 μg/g of PAH in commercial black inks. After skin tattooing, a substantial part of the ink and PAH should be transported to other anatomical sites like the regional lymph nodes. To allow a first estimation of health risk, we aimed to extract and quantify the amount of PAH in black tattooed skin and the regional lymph nodes of pre-existing tattoos. Firstly, we established an extraction method by using HPLC-DAD technology that enables the quantification of PAH concentrations in human tissue. After that, 16 specimens of human tattooed skin and corresponding regional lymph nodes were included in the study. All skin specimen and lymph nodes appeared deep black. The specimens were digested and tested for 20 different PAH at the same time.PAH were found in twelve of the 16 tattooed skin specimens and in eleven regional lymph nodes. The PAH concentration ranged from 0.1-0.6 μg/cm2 in the tattooed skin and 0.1-11.8 μg/g in the lymph nodes. Two major conclusions can be drawn from the present results. Firstly, PAH in black inks stay partially in skin or can be found in the regional lymph nodes. Secondly, the major part of tattooed PAH had disappeared from skin or might be found in other organs than skin and lymph nodes. Thus, beside inhalation and ingestion, tattooing has proven to be an additional, direct and effective route of PAH uptake into the human body.

Black tattoos entail substantial uptake of genotoxicpolycyclic aromatic hydrocarbons (PAH in human skin and regional lymph nodes.

Directory of Open Access Journals (Sweden)

Karin Lehner

Full Text Available Hundreds of millions of people worldwide have tattoos, which predominantly contain black inks consisting of soot products like Carbon Black or polycyclic aromatic hydrocarbons (PAH. We recently found up to 200 μg/g of PAH in commercial black inks. After skin tattooing, a substantial part of the ink and PAH should be transported to other anatomical sites like the regional lymph nodes. To allow a first estimation of health risk, we aimed to extract and quantify the amount of PAH in black tattooed skin and the regional lymph nodes of pre-existing tattoos. Firstly, we established an extraction method by using HPLC-DAD technology that enables the quantification of PAH concentrations in human tissue. After that, 16 specimens of human tattooed skin and corresponding regional lymph nodes were included in the study. All skin specimen and lymph nodes appeared deep black. The specimens were digested and tested for 20 different PAH at the same time.PAH were found in twelve of the 16 tattooed skin specimens and in eleven regional lymph nodes. The PAH concentration ranged from 0.1-0.6 μg/cm2 in the tattooed skin and 0.1-11.8 μg/g in the lymph nodes. Two major conclusions can be drawn from the present results. Firstly, PAH in black inks stay partially in skin or can be found in the regional lymph nodes. Secondly, the major part of tattooed PAH had disappeared from skin or might be found in other organs than skin and lymph nodes. Thus, beside inhalation and ingestion, tattooing has proven to be an additional, direct and effective route of PAH uptake into the human body.

Geostatistical analysis and isoscape of ice core derived water stable isotope records in an Antarctic macro region

Science.gov (United States)

Hatvani, István Gábor; Leuenberger, Markus; Kohán, Balázs; Kern, Zoltán

2017-09-01

Water stable isotopes preserved in ice cores provide essential information about polar precipitation. In the present study, multivariate regression and variogram analyses were conducted on 22 δ2H and 53 δ18O records from 60 ice cores covering the second half of the 20th century. Taking the multicollinearity of the explanatory variables into account, as also the model's adjusted R2 and its mean absolute error, longitude, elevation and distance from the coast were found to be the main independent geographical driving factors governing the spatial δ18O variability of firn/ice in the chosen Antarctic macro region. After diminishing the effects of these factors, using variography, the weights for interpolation with kriging were obtained and the spatial autocorrelation structure of the dataset was revealed. This indicates an average area of influence with a radius of 350 km. This allows the determination of the areas which are as yet not covered by the spatial variability of the existing network of ice cores. Finally, the regional isoscape was obtained for the study area, and this may be considered the first step towards a geostatistically improved isoscape for Antarctica.

Crystallization and preliminary X-ray analysis of the major peanut allergen Ara h 1 core region

International Nuclear Information System (INIS)

Cabanos, Cerrone; Urabe, Hiroyuki; Masuda, Taro; Tandang-Silvas, Mary Rose; Utsumi, Shigeru; Mikami, Bunzo; Maruyama, Nobuyuki

2010-01-01

In this study, the core region of Ara h 1, one of the major peanut allergens, has been overexpressed in Escherichia coli, purified and crystallized. Diffraction data were collected to 2.25 Å resolution. Peanuts contain some of the most potent food allergens known to date. Ara h 1 is one of the three major peanut allergens. As a first step towards three-dimensional structure elucidation, recombinant Ara h 1 core region was cloned, expressed in Escherichia coli and purified to homogeneity. Crystals were obtained using 0.1 M sodium citrate pH 5.6, 0.1 M NaCl, 15% PEG 400 as precipitant. The crystals diffracted to 2.25 Å resolution using synchrotron radiation and belonged to the monoclinic space group C2, with unit-cell parameters a = 156.521, b = 88.991, c = 158.971 Å, β = 107.144°. Data were collected at the BL-38B1 station of SPring-8 (Hyogo, Japan)

Plasma devices for hydrocarbon reformation

KAUST Repository

Cha, Min

2017-01-01

Plasma devices for hydrocarbon reformation are provided. Methods of using the devices for hydrocarbon reformation are also provided. The devices can include a liquid container to receive a hydrocarbon source, and a plasma torch configured

Comparative Genomics of the Ubiquitous, Hydrocarbon-degrading Genus Marinobacter

Science.gov (United States)

Singer, E.; Webb, E.; Edwards, K. J.

2012-12-01

The genus Marinobacter is amongst the most ubiquitous in the global oceans and strains have been isolated from a wide variety of marine environments, including offshore oil-well heads, coastal thermal springs, Antarctic sea water, saline soils and associations with diatoms and dinoflagellates. Many strains have been recognized to be important hydrocarbon degraders in various marine habitats presenting sometimes extreme pH or salinity conditions. Analysis of the genome of M. aquaeolei revealed enormous adaptation versatility with an assortment of strategies for carbon and energy acquisition, sensation, and defense. In an effort to elucidate the ecological and biogeochemical significance of the Marinobacters, seven Marinobacter strains from diverse environments were included in a comparative genomics study. Genomes were screened for metabolic and adaptation potential to elucidate the strategies responsible for the omnipresence of the Marinobacter genus and their remedial action potential in hydrocarbon-polluted waters. The core genome predominantly encodes for key genes involved in hydrocarbon degradation, biofilm-relevant processes, including utilization of external DNA, halotolerance, as well as defense mechanisms against heavy metals, antibiotics, and toxins. All Marinobacter strains were observed to degrade a wide spectrum of hydrocarbon species, including aliphatic, polycyclic aromatic as well as acyclic isoprenoid compounds. Various genes predicted to facilitate hydrocarbon degradation, e.g. alkane 1-monooxygenase, appear to have originated from lateral gene transfer as they are located on gene clusters of 10-20% lower GC-content compared to genome averages and are flanked by transposases. Top ortholog hits are found in other hydrocarbon degrading organisms, e.g. Alcanivorax borkumensis. Strategies for hydrocarbon uptake encoded by various Marinobacter strains include cell surface hydrophobicity adaptation via capsular polysaccharide biosynthesis and attachment

H2-rich and Hydrocarbon Gas Recovered in a Deep Precambrian Well in Northeastern Kansas

International Nuclear Information System (INIS)

Newell, K. David; Doveton, John H.; Merriam, Daniel F.; Lollar, Barbara Sherwood; Waggoner, William M.; Magnuson, L. Michael

2007-01-01

In late 2005 and early 2006, the WTW Operating, LLC (W.T.W. Oil Co., Inc.) no. 1 Wilson well (T.D. = 5772 ft; 1759.3 m) was drilled for 1826 ft (556.6 m) into Precambrian basement underlying the Forest City Basin in northeastern Kansas. Approximately 4500 of the 380,000 wells drilled in Kansas penetrate Precambrian basement. Except for two previous wells drilled into the arkoses and basalts of the 1.1-Ga Midcontinent Rift and another well drilled in 1929 in basement on the Nemaha Uplift east of the Midcontinent Rift, this well represents the deepest penetration into basement rocks in the state to date. Granite is the typical lithology observed in wells that penetrate the Precambrian in the northern Midcontinent. Although no cores were taken to definitively identify lithologies, well cuttings and petrophysical logs indicate that this well encountered basement metamorphic rocks consisting of schist, gneiss, and amphibolitic gneiss, all cut by aplite dikes.The well was cased and perforated in the Precambrian, and then acidized. After several days of swabbing operations, the well produced shows of low-Btu gas, dominated by the non-flammable component gases of nitrogen (20%), carbon dioxide (43%), and helium (1%). Combustible components include methane (26%), hydrogen (10%), and higher molecular-weight hydrocarbons (1%). Although Coveney and others [Am. Assoc. Petroleum Geologists Bull., v. 71, no, 1, p. 39-48, 1987] identified H 2 -rich gas in two wells located close to the Midcontinent Rift in eastern Kansas, this study indicates that high levels of H 2 may be a more widespread phenomenon than previously thought. Unlike previous results, the gases in this study have a significant component of hydrocarbon gas, as well as H 2 , N 2 , and CO 2 . Although redox reactions between iron-bearing minerals and groundwater are a possible source of H 2 in the Precambrian basement rocks, the hydrocarbon gas does not exhibit the characteristics typically associated with proposed

Hydrocarbons on Saturn's satellites Iapetus and Phoebe

Science.gov (United States)

Cruikshank, D.P.; Wegryn, E.; Dalle, Ore C.M.; Brown, R.H.; Bibring, J.-P.; Buratti, B.J.; Clark, R.N.; McCord, T.B.; Nicholson, P.D.; Pendleton, Y.J.; Owen, T.C.; Filacchione, G.; Coradini, A.; Cerroni, P.; Capaccioni, F.; Jaumann, R.; Nelson, R.M.; Baines, K.H.; Sotin, Christophe; Bellucci, G.; Combes, M.; Langevin, Y.; Sicardy, B.; Matson, D.L.; Formisano, V.; Drossart, P.; Mennella, V.

2008-01-01

Material of low geometric albedo (pV ??? 0.1) is found on many objects in the outer Solar System, but its distribution in the saturnian satellite system is of special interest because of its juxtaposition with high-albedo ice. In the absence of clear, diagnostic spectral features, the composition of this low-albedo (or "dark") material is generally inferred to be carbon-rich, but the form(s) of the carbon is unknown. Near-infrared spectra of the low-albedo hemisphere of Saturn's satellite Iapetus were obtained with the Visible-Infrared Mapping Spectrometer (VIMS) on the Cassini spacecraft at the fly-by of that satellite of 31 December 2004, yielding a maximum spatial resolution on the satellite's surface of ???65 km. The spectral region 3-3.6 ??m reveals a broad absorption band, centered at 3.29 ??m, and concentrated in a region comprising about 15% of the low-albedo surface area. This is identified as the C{single bond}H stretching mode vibration in polycyclic aromatic hydrocarbon (PAH) molecules. Two weaker bands attributed to {single bond}CH2{single bond} stretching modes in aliphatic hydrocarbons are found in association with the aromatic band. The bands most likely arise from aromatic and aliphatic units in complex macromolecular carbonaceous material with a kerogen- or coal-like structure, similar to that in carbonaceous meteorites. VIMS spectra of Phoebe, encountered by Cassini on 11 June 2004, also show the aromatic hydrocarbon band, although somewhat weaker than on Iapetus. The origin of the PAH molecular material on these two satellites is unknown, but PAHs are found in carbonaceous meteorites, cometary dust particles, circumstellar dust, and interstellar dust. ?? 2007 Elsevier Inc. All rights reserved.

Historical records of polycyclic aromatic hydrocarbon deposition in a shallow eutrophic lake: Impacts of sources and sedimentological conditions.

Science.gov (United States)

Li, Chaocan; Huo, Shouliang; Yu, Zhiqiang; Guo, Wei; Xi, Beidou; He, Zhuoshi; Zeng, Xiangying; Wu, Fengchang

2016-03-01

Sediment core samples collected from Lake Chaohu were analyzed for 15 priority polycyclic aromatic hydrocarbons (PAHs) to assess the spatial and temporal distributions of the PAHs during lacustrine sedimentary processes and regional economic development. Assessing the PAH sedimentary records over an approximately 100-year time span, we identified two stages in the PAH inputs and sources (before the 1970s and after the 1970s) in the eastern lake region near a village, whereas three stages (before the 1950s, 1950s-1990s and after the 1990s) were identified in the western lake region near urban and industrial areas. Rapid increases in the PAH depositional fluxes occurred during the second stage due to increased human activities in the Lake Chaohu basin. The composition and isomeric ratios of the PAHs revealed that pyrolysis is the main source of PAHs in this lake. Strong positive relationships between PAH concentration and the total organic carbon concentration, sediment grain size (energy consumption and the levels of urban industrialization and civilization, affect both the composition and abundance of the PAHs. Copyright © 2015. Published by Elsevier B.V.

[Core competencies in public health: a regional framework for the Americas].

Science.gov (United States)

Conejero, Juana Suárez; Godue, Charles; Gutiérrez, José Francisco García; Valladares, Laura Magaña; Rabionet, Silvia; Concha, José; Valdés, Manuel Vázquez; Gómez, Rubén Darío; Mujica, Oscar J; Cabezas, César; Lucano, Lindaura Liendo; Castellanos, Jorge

2013-07-01

The response is described to the 2010 call from the Pan American Health Organization to develop a Regional Framework on Core Competencies in Public Health, with a view to supporting the efforts of the countries in the Americas to build public health systems capacity as a strategy for optimal performance of the Essential Public Health Functions. The methodological process for the response was divided into four phases. In the first, a team of experts was convened who defined the methodology to be used during a workshop at the National Institute of Public Health of Mexico in 2010. The second phase involved formation of the working groups, using two criteria: experience and multidisciplinary membership, which resulted in a regional team with 225 members from 12 countries. This team prepared an initial proposal with 88 competencies. In the third phase, the competencies were cross-validated and their number reduced to 64. During the fourth phase, which included two workshops, in March 2011 (Medellín, Colombia) and June 2011 (Lima, Peru), discussions centered on analyzing the association between the results and the methodology.

Source apportionment of hydrocarbons measured in the Eagle Ford shale

Science.gov (United States)

Roest, G. S.; Schade, G. W.

2016-12-01

The rapid development of unconventional oil and gas in the US has led to hydrocarbon emissions that are yet to be accurately quantified. Emissions from the Eagle Ford Shale in southern Texas, one of the most productive shale plays in the U.S., have received little attention due to a sparse air quality monitoring network, thereby limiting studies of air quality within the region. We use hourly atmospheric hydrocarbon and meteorological data from three locations in the Eagle Ford Shale to assess their sources. Data are available from the Texas commission of environmental quality (TCEQ) air quality monitors in Floresville, a small town southeast of San Antonio and just north of the shale area; and Karnes city, a midsize rural city in the center of the shale. Our own measurements were carried out at a private ranch in rural Dimmit County in southern Texas from April to November of 2015. Air quality monitor data from the TCEQ were selected for the same time period. Non-negative matrix factorization in R (package NMF) was used to determine likely sources and their contributions above background. While the TCEQ monitor data consisted mostly of hydrocarbons, our own data include both CO, CO2, O3, and NOx. We find that rural Dimmit County hydrocarbons are dominated by oil and gas development sources, while central shale hydrocarbons at the TCEQ monitoring sites have a mix of sources including car traffic. However, oil and gas sources also dominate hydrocarbons at Floresville and Karnes City. Toxic benzene is nearly exclusively due to oil and gas development sources, including flaring, which NMF identifies as a major hydrocarbon source in Karnes City. Other major sources include emissions of light weight alkanes (C2-C5) from raw natural gas emissions and a larger set of alkanes (C2-C10) from oil sources, including liquid storage tanks.

A core design study for 'zero-sodium-void-worth' cores

International Nuclear Information System (INIS)

Kawashima, Masatoshi; Suzuki, Masao; Hill, R.N.

1992-01-01

Recently, a number of low sodium-void-worth metal-fueled core design concepts have been proposed; to provide for flexibility in transuranic nuclide management strategy, core designs which exhibit a wide range of breeding characteristics have been developed. Two core concepts, a flat annular (transuranic burning) core and an absorber-type parfait (transuranic self-sufficient) core, are selected for this study. In this paper, the excess reactivity management schemes applied in the two designs are investigated in detail. In addition, the transient effect of reactivity insertions on the parfait core design is assessed. The upper and lower core regions in the parfait design are neutronically decoupled; however, the common coolant channel creates thermalhydraulic coupling. This combination of neutronic and thermalhydraulic characteristics leads to unique behavior in anticipated transient overpower events. (author)

Black Tattoos Entail Substantial Uptake of Genotoxicpolycyclic Aromatic Hydrocarbons (PAH) in Human Skin and Regional Lymph Nodes

Science.gov (United States)

Lehner, Karin; Santarelli, Francesco; Vasold, Rudolf; Penning, Randolph; Sidoroff, Alexis; König, Burkhard; Landthaler, Michael; Bäumler, Wolfgang

2014-01-01

Hundreds of millions of people worldwide have tattoos, which predominantly contain black inks consisting of soot products like Carbon Black or polycyclic aromatic hydrocarbons (PAH). We recently found up to 200 μg/g of PAH in commercial black inks. After skin tattooing, a substantial part of the ink and PAH should be transported to other anatomical sites like the regional lymph nodes. To allow a first estimation of health risk, we aimed to extract and quantify the amount of PAH in black tattooed skin and the regional lymph nodes of pre-existing tattoos. Firstly, we established an extraction method by using HPLC – DAD technology that enables the quantification of PAH concentrations in human tissue. After that, 16 specimens of human tattooed skin and corresponding regional lymph nodes were included in the study. All skin specimen and lymph nodes appeared deep black. The specimens were digested and tested for 20 different PAH at the same time.PAH were found in twelve of the 16 tattooed skin specimens and in eleven regional lymph nodes. The PAH concentration ranged from 0.1–0.6 μg/cm2 in the tattooed skin and 0.1–11.8 μg/g in the lymph nodes. Two major conclusions can be drawn from the present results. Firstly, PAH in black inks stay partially in skin or can be found in the regional lymph nodes. Secondly, the major part of tattooed PAH had disappeared from skin or might be found in other organs than skin and lymph nodes. Thus, beside inhalation and ingestion, tattooing has proven to be an additional, direct and effective route of PAH uptake into the human body. PMID:24670978

Hydrocarbons and air pollution

International Nuclear Information System (INIS)

Herz, O.

1992-01-01

This paper shows the influence of hydrocarbons vapors, emitted by transports or by volatile solvents using, on air pollution. Hydrocarbons are the principal precursors of photochemical pollution. After a brief introduction on atmospheric chemistry and photochemical reactions, the author describes the french prevention program against hydrocarbons emissions. In the last chapter, informations on international or european community programs for photochemical pollution study are given. 5 figs., 10 tabs

Non-aromatic hydrocarbons in surface sediments near the Pearl River estuary in the South China Sea

International Nuclear Information System (INIS)

Gao Xuelu; Chen Shaoyong; Xie Xueliang; Long Aimin; Ma Fujun

2007-01-01

Surface sediment samples at 4 sites along an offshore transect from outer continental shelf off the Pearl River estuary to the shelf slope region of the northern South China Sea, have been analyzed for total organic carbon (TOC), total nitrogen (TN), solvent extractable organic matter (EOM) and non-aromatic hydrocarbons. TOC, TN and EOM show distinct spatial variations. Their highest values are all recorded at the shelf slope region. EOM varies from 18.70-38.58 μg g -1 dry sediment and accounts for 0.20-0.72% of the TOC contents. The non-aromatic hydrocarbons are an important fraction of EOM. Their contents range from 3.43-7.06 μg g -1 dry sediment. n-Alkanes with carbon number ranging from 15-38 are identified. They derive from both biogenic and petrogenic sources in different proportions. Results of isoprenoid hydrocarbons, hopanes and steranes also suggest possible petroleum contamination. - Anthropogenic activities have influences on the composition of non-aromatic hydrocarbons in the surface sediments of the northern South China Sea outer continental shelf

Nonequilibrium phenomena and determination of plasma parameters in the hot core of the cathode region in free-burning arc discharges

International Nuclear Information System (INIS)

Kuehn, Gerrit; Kock, Manfred

2007-01-01

We present spectroscopic measurements of plasma parameters (electron density n e , electron temperature T e , gas temperature T g , underpopulation factor b) in the hot-core region in front of the cathode of a low-current, free-burning arc discharge in argon under atmospheric pressure. The discharge is operated in the hot-core mode, creating a hot cathode region with plasma parameters similar to high-current arcs in spite of the fact that we use comparatively low currents (less than 20 A). We use continuum emission and (optically thin) line emission to determine n e and T e . We apply relaxation measurements based on a power-interruption technique to investigate deviations from local thermodynamic equilibrium (LTE). These measurements let us determine the gas temperature T g . All measurements are performed side-on with charge-coupled-device cameras as detectors, so that all measured plasma parameters are spatially resolved after an Abel inversion. This yields the first ever spatially resolved observation of the non-LTE phenomena of the hot core in the near-cathode region of free-burning arcs. The results only partly coincide with previously published predictions and measurements in the literature

Assessment of natural hydrocarbon bioremediation at two gas condensate production sites

International Nuclear Information System (INIS)

Barker, G.W.; Raterman, K.T.; Fisher, J.B.; Corgan, J.M.; Trent, G.L.; Brown, D.R.; Sublette, K.L.

1995-01-01

Condensate liquids are present in soil and groundwater at two gas production sites in the Denver-Julesburg Basin operated by Amoco. These sites have been closely monitored since July 1993 to determine whether intrinsic aerobic or anaerobic bioremediation of hydrocarbons occurs at a sufficient rate and to an adequate endpoint to support a no-intervention decision. Groundwater monitoring and analysis of soil cores strongly suggest that intrinsic bioremediation is occurring at these sites by multiple pathways, including aerobic oxidation, Fe(III) reduction, and sulfate reduction

Biological risk and pollution history of polycyclic aromatic hydrocarbons (PAHs) in Nansha mangrove, South China.

Science.gov (United States)

Wu, Qihang; Leung, Jonathan Y S; Tam, Nora F Y; Chen, Shejun; Mai, Bixian; Zhou, Xizhen; Xia, Lihua; Geng, Xinhua

2014-08-15

Chinese government has taken various measures to alleviate pollution caused by polycyclic aromatic hydrocarbons (PAHs) in the region of Pearl River Delta since the economic reform in 1978, but the effectiveness of these measures remains largely unknown. This study aimed to elucidate the biological risk and pollution history of PAHs by measuring the concentrations of 28 PAHs in the surface and core sediments, respectively, in Nansha mangrove. Results found that the biological risk of PAHs was low without obvious spatial variation. The PAH concentration along the depth gradient indicated that PAH pollution was stabilized since the early 1990s while the source of PAHs has gradually changed from combustion of coal to petroleum products. This implied that the mitigation measures taken by the Chinese government were effective. Compared to marine bottom sediment, we propose that using mangrove sediment can provide a more accurate and precise estimate of pollution history of PAHs. Copyright © 2014 Elsevier Ltd. All rights reserved.

SCDAP/RELAP5 lower core plate model

International Nuclear Information System (INIS)

Coryell, E.W.; Griffin, F.P.

1999-01-01

The SCDAP/RELAP5 computer code is a best-estimate analysis tool for performing nuclear reactor severe accident simulations. This report describes the justification, theory, implementation, and testing of a new modeling capability which will refine the analysis of the movement of molten material from the core region to the vessel lower head. As molten material moves from the core region through the core support structures it may encounter conditions which will cause it to freeze in the region of the lower core plate, delaying its arrival to the vessel head. The timing of this arrival is significant to reactor safety, because during the time span for material relocation to the lower head, the core may be experiencing steam-limited oxidation. The time at which hot material arrives in a coolant-filled lower vessel head, thereby significantly increasing the steam flow rate through the core region, becomes significant to the progression and timing of a severe accident. This report is a revision of a report INEEL/EXT-00707, entitled ''Preliminary Design Report for SCDAP/RELAP5 Lower Core Plate Model''

Fuel and core design study of the sodium-cooled fast reactors. Studies on metallic fuel cores in the JFY2002

International Nuclear Information System (INIS)

Sugino, Kazuteru; Mizuno, Tomoyasu

2003-06-01

Based on the results obtained in the former feasibility study, the metallic fueled core of ordinary-type, that is, 2-region homogeneous core, has been established aiming at the improvement in the core performance, and subsequent comparison has been performed with the mixed oxide fueled core. Further, the attractive concept of the metallic fueled core of high outlet temperature has been constructed which has good nuclear features as a metallic fueled core and has identical outlet temperature to mixed oxide fuelled core. Following items have been found as a result of the investigation on the ordinary-type core. The metallic fueled core whose maximum fast neutron fluence (En>0.1MeV) is set identical (5x10 23 n/cm 2 ) to the mixed oxide fueled cores with core discharge burnup 150GWd/t has sufficient core performances as a metallic fueled core, e.g. higher breeding ratio and longer operation period compared with mixed oxide fueled cores, but the core discharge burnup is limited up to 100GWd/t. However effective discharge burnup including the contribution of the blanket region is comparative to mixed oxide cores under the same breeding ratio condition. In order to enlarge the core discharge burnup to 150GWd/t keeping the core performance identical to above mentioned core's, the irradiation deformation of structural material should be reduced to that of mixed oxide fueled cores. Further the maximum fast neutron fluence reaches to 7-8x10 23 n/cm 2 (En>0.1MeV). The investigations on the core of high outlet temperature have clarified following items. Even in the change of core regions by pin-diameter form 3-region to 2-region and in the limited maximum fuel pin diameter 8.5 mm, realization of the identical outlet/inlet temperatures to the mixed oxide cores (550/395degC) is feasible under the criteria of the maximum temperature 650degC at the inner surface of the cladding. The constructed core accommodates the targets of breeding ratio from about 1.0 to 1.2 only by adjusting

Methodology for the detection of contamination by hydrocarbons and further soil sampling for volatile and semi-volatile organic enrichment in former petrol stations, SE Spain

Directory of Open Access Journals (Sweden)

Rosa María Rosales Aranda

2012-01-01

Full Text Available The optimal detection and quantification of contamination plumes in soil and groundwater by petroleum organic compounds, gasoline and diesel, is critical for the reclamation of hydrocarbons contaminated soil at petrol stations. Through this study it has been achieved a sampling stage optimization in these scenarios by means of the location of potential contamination areas before sampling with the application of the 2D electrical resistivity tomography method, a geophysical non destructive technique based on resistivity measurements in soils. After the detection of hydrocarbons contaminated areas, boreholes with continuous coring were performed in a petrol station located in Murcia Region (Spain. The drillholes reached depths down to 10 m and soil samples were taken from each meter of the drilling. The optimization in the soil samples handling and storage, for both volatile and semi-volatile organic compounds determinations, was achieved by designing a soil sampler to minimize volatilization losses and in order to avoid the manual contact with the environmental samples during the sampling. The preservation of soil samples was performed according to Europe regulations and US Environmental Protection Agency recommendations into two kinds of glass vials. Moreover, it has been taken into account the determination techniques to quantify the hydrocarbon pollution based on Gas Chromatography with different detectors and headspace technique to reach a liquid-gas equilibrium for volatile analyses.

Detection of hydrocarbons in irradiated foods

International Nuclear Information System (INIS)

Miyahara, Makoto; Maitani, Tamio; Saito, Akiko; Kamimura, Tomomi; Nagasawa, Taeko; Kobayashi, Yasuo; Ito, Hitoshi

2003-01-01

The hydrocarbon method for the detection of irradiated foods is now recognized as the international technique. This method is based on radiolysis of fatty acids in food to give hydrocarbons. In order to expand this technique's application, ten foods (butter, cheese, chicken, pork, beef, tuna, dry shrimp, avocado, papaya, and mango) were irradiated in the range from 0.5 to 10 kGy and the hydrocarbons in them were detected. Recoveries of the hydrocarbons from most foods were acceptable (38-128%). Some hydrocarbons were found in non-irradiated foods, particularly, in butter, cheese, tuna, and shrimp. Seven irradiated foods, butter, cheese, chicken, beef, pork, tuna, dry shrimp, and avocado were detectable at their practical doses by measuring the appropriate marker hydrocarbons. In most case, marker hydrocarbon will be 1,7-hexadecadiene. However, the marker hydrocarbons produced only in irradiated foods varied from food to food; therefore, it is necessary to check a specific irradiated food for marker hydrocarbons. On the other hand, two irradiated foods (papaya and mango which were irradiated at their practical doses) were difficult to distinguish from non-irradiated foods using this method. (author)

Detection of hydrocarbons in irradiated foods

Energy Technology Data Exchange (ETDEWEB)

Miyahara, Makoto; Maitani, Tamio [National Inst. of Health Sciences, Tokyo (Japan); Saito, Akiko; Kamimura, Tomomi; Nagasawa, Taeko [Kitasato Univ., Sagamihara, Kanagawa (Japan). School of Allied Health Sciences; Kobayashi, Yasuo; Ito, Hitoshi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Establishment

2003-06-01

The hydrocarbon method for the detection of irradiated foods is now recognized as the international technique. This method is based on radiolysis of fatty acids in food to give hydrocarbons. In order to expand this technique's application, ten foods (butter, cheese, chicken, pork, beef, tuna, dry shrimp, avocado, papaya, and mango) were irradiated in the range from 0.5 to 10 kGy and the hydrocarbons in them were detected. Recoveries of the hydrocarbons from most foods were acceptable (38-128%). Some hydrocarbons were found in non-irradiated foods, particularly, in butter, cheese, tuna, and shrimp. Seven irradiated foods, butter, cheese, chicken, beef, pork, tuna, dry shrimp, and avocado were detectable at their practical doses by measuring the appropriate marker hydrocarbons. In most case, marker hydrocarbon will be 1,7-hexadecadiene. However, the marker hydrocarbons produced only in irradiated foods varied from food to food; therefore, it is necessary to check a specific irradiated food for marker hydrocarbons. On the other hand, two irradiated foods (papaya and mango which were irradiated at their practical doses) were difficult to distinguish from non-irradiated foods using this method. (author)

Non-methane hydrocarbon characteristics of motor vehicular emissions in the Pearl River Delta region

Science.gov (United States)

Tsai, Wai Yan

2007-12-01

Air pollution problem in Hong Kong and the Pearl River Delta (PRD) region has raised much concern from the public in recent years. The primary aim of this research is to use field measurement data to characterize non-methane hydrocarbons (NMHCs) in emission from motor vehicles. Fuel vapor compositions for several commonly used vehicular fuels in Hong Kong, Macau, Guangzhou and Zhuhai were analyzed in 2003, and they are believed to be the first one reported for the PRD region. These profiles were used to study the impact of evaporative loss of the fuels on air quality. From the roadside and tunnel samples collected in the four cities mentioned above from 2000 to 2003, results showed that vehicular engine combustion was a main NMHC source, while gasoline evaporative losses also contributed much to the total NMHC emission, besides, LPG leakage was also found to be significant from the tunnel measurement data collected in Hong Kong. Characteristics of vehicular engine exhaust emissions were also studied. Measurements of diesel emission showed a large influence on the emission profile due to the change of diesel compositions. The E/E ratios implied that gasoline-powered vehicles in Hong Kong were equipped with well functioning catalysts, while those in Guangzhou and Zhuhai, especially the motorcycles, were found dirtier in NMHC emission. Although the E/E ratios showed that private cars in Hong Kong had high combustion efficiency, the existence of significant amounts of unburned gasoline in their exhaust stream pointed out that they still had low fuel economy. From the results of a simple model, it was found that the evaporative losses of gasoline and LPG contributed much to the total NMHC pollution from vehicle. The preliminary results from the dynamometer study conducted in Hong Kong showed large variations of exhaust characteristics for private cars and taxis during different driving speeds. The results can be used as scientific basis for regulatory parties in

Tolerance of Antarctic soil fungi to hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Hughes, Kevin A.; Bridge, Paul; Clark, Melody S. [British Antarctic Survey, Natural Environment Research Council, High Cross, Madingley Road, Cambridge CB3 0ET (United Kingdom)

2007-01-01

Little is known about the effects of hydrocarbons and fuel oil on Antarctic filamentous fungi in the terrestrial Antarctic environment. Growth of fungi and bacteria from soils around Rothera Research Station (Adelaide Island, Antarctic Peninsula) was assessed in the presence of ten separate aromatic and aliphatic hydrocarbons [marine gas oil (MGO), dodecane, hexadecane, benzoic acid, p-hydroxybenzoic acid, toluene, phenol, biphenyl, naphthalene and m- and p-xylenes with ethylbenzene]. Aromatic hydrocarbons inhibited soil microbial growth more than aliphatic hydrocarbons. Soil microorganisms from a moss patch, where little previous impact or hydrocarbon contamination had occurred, were less tolerant of hydrocarbons than those from high impact sites. Fungal growth rates of Mollisia sp., Penicillium commune, Mortierella sp., Trichoderma koningii, Trichoderma sp. and Phoma herbarum were assessed in the presence of hydrocarbons. Generally, aromatic hydrocarbons inhibited or stopped hyphal extension, though growth rates increased with some aliphatic hydrocarbons. Hyphal dry weight measurements suggested that Mortierella sp. may be able to use dodecane as sole carbon and energy source. Hydrocarbon-degrading Antarctic fungi may have use in future hydrocarbon spill bioremediation. (author)

Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site

International Nuclear Information System (INIS)

Akbari, Ali; Ghoshal, Subhasis

2014-01-01

Highlights: • Aeration and moisture addition alone caused extensive hydrocarbon biodegradation. • 30-day slurry reactor remediation endpoints attained in 385 days in biopiles. • High nitrogen concentrations inhibited hydrocarbon degradation. • Inhibition of biodegradation linked to lack of shifts in soil microbial community. - Abstract: Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16–C34) in a pilot-scale biopile experiment conducted at 15 °C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16–C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day −1 in biopile tank compared to 0.11 day −1 in slurry bioreactors for C16–C34 hydrocarbons, the biodegradation extents for this fraction were

Evidence of stochastic region near a rational surface in core plasmas of LHD

International Nuclear Information System (INIS)

Ida, K.; Tamura, N.; Tuchiya, H.

2010-11-01

Clear evidence of stochastization of the magnetic surfaces near a rational surface is observed in the core plasma with weak magnetic shear in the Large Helical Device (LHD) by applying heat pulses driven by modulated electron cyclotron heating (MECH). The stochastization of the magnetic surfaces is confirmed by the observation of flattening of electron temperature (T e ) profiles and very fast propagation of the heat pulse, which is in contrast to the slow heat pulse propagation observed in the T e flat region of the nested magnetic island. (author)

Sediment record of polycyclic aromatic hydrocarbons in the Liaohe River Delta wetland, Northeast China: Implications for regional population migration and economic development.

Science.gov (United States)

Ma, Chuanliang; Lin, Tian; Ye, Siyuan; Ding, Xigui; Li, Yuanyuan; Guo, Zhigang

2017-03-01

The polycyclic aromatic hydrocarbons (PAHs) of a 210 Pb-dated sediment core extracted from the Liaohe River Delta wetland were measured to reconstruct the sediment record of PAHs and its response to human activity for the past 300 years in Northeast China. The concentrations of the 16 U.S. Environmental Protection Agency priority PAHs (∑16PAHs) ranged from 46 to 1167 ng g -1 in this sediment core. The concentrations of the 16 PAHs (especially 4- and 5+6-ring PAHs) after the 1980s (surface sediments 0-6 cm) were one or two orders of magnitudes higher than those of the down-core samples. The exponential growth of 4-ring and 5+6-ring PAH concentrations after the 1980s responded well to the increased energy consumption and number of civil vehicles resulting from the rapid economic development in China. Prior to 1950, relatively low levels of the 16 PAHs and a high proportion of 2+3-ring PAHs was indicative of biomass burning as the main source of the PAHs. A significant increase in the 2 + 3 ring PAH concentration from the 1860s-1920s was observed and could be attributed to a constant influx of population migration into Northeast China. It was suggested that the link between historical trend of PAHs and population or energy use involves two different economic stages. Typically, in an agricultural economy, the greater the population size, the greater the emission of PAHs from biomass burning, while in an industrial economy, the increase in sedimentary PAH concentrations is closely related to increasing energy consumption of fossil fuels. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fuel assembly and reactor core

International Nuclear Information System (INIS)

Yuchi, Yoko; Aoyama, Motoo; Haikawa, Katsumasa; Yamanaka, Akihiro; Koyama, Jun-ichi.

1996-01-01

In a fuel assembly of a BWR type reactor, a region substantially containing burnable poison is divided into an upper region and a lower region having different average concentrations of burnable poison along a transverse cross section perpendicular to the axial direction. The ratio of burnable poison contents of both regions is determined to not more than 80%, and the average concentration of the burnable poison in the lower region is determined to not less than 9% by weight. An infinite multiplication factor at an initial stage of the burning of the fuel assembly is controlled effectively by the burnable poisons. Namely, the ratio of the axial power can be controlled by the distribution of the enrichment degree of uranium fuels and the distribution of the burnable poison concentration in the axial direction. Since the average enrichment degree of the reactor core has to be increased in order to provide an initially loaded reactor core at high burnup degree. Distortion of the power distribution in the axial direction of the reactor core to which fuel assemblies at high enrichment degree are loaded is flattened to improve thermal margin, to extend continuous operation period and increase a burnup degree upon take-out thereby improving fuel economy without worsening the reactor core characteristics of the initially loaded reactor core. (N.H.)

National Gas Hydrate Program Expedition 01 offshore India; gas hydrate systems as revealed by hydrocarbon gas geochemistry

Science.gov (United States)

Lorenson, Thomas; Collett, Timothy S.

2018-01-01

The National Gas Hydrate Program Expedition 01 (NGHP-01) targeted gas hydrate accumulations offshore of the Indian Peninsula and along the Andaman convergent margin. The primary objectives of coring were to understand the geologic and geochemical controls on the accumulation of methane hydrate and their linkages to underlying petroleum systems. Four areas were investigated: 1) the Kerala-Konkan Basin in the eastern Arabian Sea, 2) the Mahanadi and 3) Krishna-Godavari Basins in the western Bay of Bengal, and 4) the Andaman forearc Basin in the Andaman Sea.Upward flux of methane at three of the four of the sites cored during NGHP-01 is apparent from the presence of seafloor mounds, seismic evidence for upward gas migration, shallow sub-seafloor geochemical evidence of methane oxidation, and near-seafloor gas composition that resembles gas from depth.The Kerala-Konkan Basin well contained only CO2 with no detectable hydrocarbons suggesting there is no gas hydrate system here. Gas and gas hydrate from the Krishna-Godavari Basin is mainly microbial methane with δ13C values ranging from −58.9 to −78.9‰, with small contributions from microbial ethane (−52.1‰) and CO2. Gas from the Mahanadi Basin was mainly methane with lower concentrations of C2-C5 hydrocarbons (C1/C2 ratios typically >1000) and CO2. Carbon isotopic compositions that ranged from −70.7 to −86.6‰ for methane and −62.9 to −63.7‰ for ethane are consistent with a microbial gas source; however deeper cores contained higher molecular weight hydrocarbon gases suggesting a small contribution from a thermogenic gas source. Gas composition in the Andaman Basin was mainly methane with lower concentrations of ethane to isopentane and CO2, C1/C2 ratios were mainly >1000 although deeper samples were exploration and occurs in a forearc basin. Each of these hydrate-bearing systems overlies and is likely supported by the presence and possible migration of gas from deeper gas-prone petroleum

IAEA Regional Workshop on Development and Validation of EOP/AMG for Effective Prevention/Mitigation of Severe Core Damage

International Nuclear Information System (INIS)

1999-01-01

Materials of the IAEA Regional Workshop contain 24 presented lectures. Authors deal with development and validation of emergency operating procedures as well as with accident management guidelines (EOP/AMG) for effective prevention and mitigation of severe core damage

Production of light hydrocarbons, etc. [from heavy hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

1937-10-07

A process is given for the production of light hydrocarbons of the gasoline type and, if desired, of the middle-oil type, from liquid or fusible heavy or medium heavy hydrocarbon materials. The process comprises subjecting the said initial materials in the first stage to catalytic hydrofining, separating the lower boiling constituents and the hydrogenating gas from the resulting products and then subjecting the higher boiling constituents in a second stage to a splitting destructive hydrogenation and then recycling substantially the entire reaction mixture obtained in the second stage to the frst stage.

Spectral Comparison and Stability of Red Regions on Jupiter

Science.gov (United States)

Simon, A. A.; Carlson, R. W.; Sanchez-Lavega, A.

2013-01-01

A study of absolute color on Jupiter from Hubble Space Telescope imaging data shows that the Great Red Spot (GRS) is not the reddest region of the planet. Rather, a transient red cyclone visible in 1995 and the North Equatorial Belt both show redder spectra than the GRS (i.e., more absorption at blue and green wavelengths). This cyclone is unique among vortices in that it is intensely colored yet low altitude, unlike the GRS. Temporal analysis shows that the darkest regions of the NEB are relative constant in color from 1995 to 2008, while the slope of the GRS core may vary slightly. Principal component analysis shows several spectral components are needed, in agreement with past work, and further highlights the differences between regions. These color differences may be indicative of the same chromophore(s) under different conditions, such as mixing with white clouds, longer UV irradiation at higher altitude, and thermal processing, or may indicate abundance variations in colored compounds. A single compound does not fit the spectrum of any region well and mixes of multiple compounds including NH4SH, photolyzed NH3, hydrocarbons, and possibly P4, are likely needed to fully match each spectrum.

GOM Deepwater Horizon Oil Spill: A Time Series Analysis of Variations in Spilled Hydrocarbons

Science.gov (United States)

Palomo, C. M.; Yan, B.

2013-12-01

An estimated amount of 210 million gallons of crude oil was released into the Gulf of Mexico (GOM) from April 20th to July 15th 2010 during the Deepwater Horizon oil rig explosion. The spill caused a tremendous financial, ecological, environmental and health impact and continues to affect the GOM today. Variations in hydrocarbons including alkanes, hopanes and poly-cyclic aromatic hydrocarbons (PAHs) can be analyzed to better understand the oil spill and assist in oil source identification. Twenty-one sediment samples*, two tar ball samples and one surface water oil sample were obtained from distinct locations in the GOM and within varying time frames from May to December 2010. Each sample was extracted through the ASE 200 solvent extractor, concentrated down under nitrogen gas, purified through an alumina column, concentrated down again with nitrogen gas and analyzed via GC X GC-TOF MS. Forty-one different hydrocarbons were quantified in each sample. Various hydrocarbon 'fingerprints,' such as parental :alkylate PAH ratios, high molecular weight PAHs: low molecular weight alkane ratios, and carbon preference index were calculated. The initial objective of this project was to identify the relative hydrocarbon contributions of petrogenic sources and combustion sources. Based on the calculated ratios, it is evident that the sediment core taken in October of 2010 was greatly affected by combustion sources. Following the first month of the spill, oil in the gulf was burned in attempts to contain the spill. Combustion related sources have quicker sedimentation rates, and hydrocarbons from a combustion source essentially move into deeper depths quicker than those from a petrogenic source, as was observed in analyses of the October 2010 sediment. *Of the twenty-one sediment samples prepared, nine were quantified for this project.

Polycyclic aromatic hydrocarbons in disks around young solar-type stars

NARCIS (Netherlands)

Geers, Vincent Carlo

2007-01-01

In this thesis we study the dust around solar-type young stars. In particular, we focus on one specific species of dust, namely the Polycyclic Aromatic Hydrocarbons (PAHs), a family of large molecules, or small grains, that are widely observed in nearby star-forming regions. We address the following

High-resolution IR absorption spectroscopy of polycyclic aromatic hydrocarbons in the 3 μm region: role of hydrogenation and alkylation

Science.gov (United States)

Maltseva, Elena; Mackie, Cameron J.; Candian, Alessandra; Petrignani, Annemieke; Huang, Xinchuan; Lee, Timothy J.; Tielens, Alexander G. G. M.; Oomens, Jos; Buma, Wybren Jan

2018-03-01

Aim. We aim to elucidate the spectral changes in the 3 μm region that result from chemical changes in the molecular periphery of polycyclic aromatic hydrocarbons (PAHs) with extra hydrogens (H-PAHs) and methyl groups (Me-PAHs). Methods: Advanced laser spectroscopic techniques combined with mass spectrometry were applied on supersonically cooled 1,2,3,4-tetrahydronaphthalene, 9,10-dihydroanthracene, 9,10-dihydrophenanthrene, 1,2,3,6,7,8-hexahydropyrene, 9-methylanthracene, and 9,10-dimethylanthracene, allowing us to record mass-selective and conformationally selective absorption spectra of the aromatic, aliphatic, and alkyl CH-stretches in the 3.175 - 3.636 µm region with laser-limited resolution. We compared the experimental absorption spectra with standard harmonic calculations and with second-order vibrational perturbation theory anharmonic calculations that use the SPECTRO program for treating resonances. Results: We show that anharmonicity plays an important if not dominant role, affecting not only aromatic, but also aliphatic and alkyl CH-stretch vibrations. The experimental high-resolution data lead to the conclusion that the variation in Me- and H-PAHs composition might well account for the observed variations in the 3 μm emission spectra of carbon-rich and star-forming regions. Our laboratory studies also suggest that heavily hydrogenated PAHs form a significant fraction of the carriers of IR emission in regions in which an anomalously strong 3 μm plateau is observed.

Versatility of hydrocarbon production in cyanobacteria.

Science.gov (United States)

Xie, Min; Wang, Weihua; Zhang, Weiwen; Chen, Lei; Lu, Xuefeng

2017-02-01

Cyanobacteria are photosynthetic microorganisms using solar energy, H 2 O, and CO 2 as the primary inputs. Compared to plants and eukaryotic microalgae, cyanobacteria are easier to be genetically engineered and possess higher growth rate. Extensive genomic information and well-established genetic platform make cyanobacteria good candidates to build efficient biosynthetic pathways for biofuels and chemicals by genetic engineering. Hydrocarbons are a family of compounds consisting entirely of hydrogen and carbon. Structural diversity of the hydrocarbon family is enabled by variation in chain length, degree of saturation, and rearrangements of the carbon skeleton. The diversified hydrocarbons can be used as valuable chemicals in the field of food, fuels, pharmaceuticals, nutrition, and cosmetics. Hydrocarbon biosynthesis is ubiquitous in bacteria, yeasts, fungi, plants, and insects. A wide variety of pathways for the hydrocarbon biosynthesis have been identified in recent years. Cyanobacteria may be superior chassis for hydrocabon production in a photosynthetic manner. A diversity of hydrocarbons including ethylene, alkanes, alkenes, and terpenes can be produced by cyanobacteria. Metabolic engineering and synthetic biology strategies can be employed to improve hydrocarbon production in cyanobacteria. This review mainly summarizes versatility and perspectives of hydrocarbon production in cyanobacteria.

MODELING GALACTIC EXTINCTION WITH DUST AND 'REAL' POLYCYCLIC AROMATIC HYDROCARBONS

International Nuclear Information System (INIS)

Mulas, Giacomo; Casu, Silvia; Cecchi-Pestellini, Cesare; Zonca, Alberto

2013-01-01

We investigate the remarkable apparent variety of galactic extinction curves by modeling extinction profiles with core-mantle grains and a collection of single polycyclic aromatic hydrocarbons. Our aim is to translate a synthetic description of dust into physically well-grounded building blocks through the analysis of a statistically relevant sample of different extinction curves. All different flavors of observed extinction curves, ranging from the average galactic extinction curve to virtually 'bumpless' profiles, can be described by the present model. We prove that a mixture of a relatively small number (54 species in 4 charge states each) of polycyclic aromatic hydrocarbons can reproduce the features of the extinction curve in the ultraviolet, dismissing an old objection to the contribution of polycyclic aromatic hydrocarbons to the interstellar extinction curve. Despite the large number of free parameters (at most the 54 × 4 column densities of each species in each ionization state included in the molecular ensemble plus the 9 parameters defining the physical properties of classical particles), we can strongly constrain some physically relevant properties such as the total number of C atoms in all species and the mean charge of the mixture. Such properties are found to be largely independent of the adopted dust model whose variation provides effects that are orthogonal to those brought about by the molecular component. Finally, the fitting procedure, together with some physical sense, suggests (but does not require) the presence of an additional component of chemically different very small carbonaceous grains.

A Core Set Based Large Vector-Angular Region and Margin Approach for Novelty Detection

Directory of Open Access Journals (Sweden)

Jiusheng Chen

2016-01-01

Full Text Available A large vector-angular region and margin (LARM approach is presented for novelty detection based on imbalanced data. The key idea is to construct the largest vector-angular region in the feature space to separate normal training patterns; meanwhile, maximize the vector-angular margin between the surface of this optimal vector-angular region and abnormal training patterns. In order to improve the generalization performance of LARM, the vector-angular distribution is optimized by maximizing the vector-angular mean and minimizing the vector-angular variance, which separates the normal and abnormal examples well. However, the inherent computation of quadratic programming (QP solver takes O(n3 training time and at least O(n2 space, which might be computational prohibitive for large scale problems. By (1+ε  and  (1-ε-approximation algorithm, the core set based LARM algorithm is proposed for fast training LARM problem. Experimental results based on imbalanced datasets have validated the favorable efficiency of the proposed approach in novelty detection.

Hydrocarbon Plume Dynamics in the Worldś Most Spectacular Hydrocarbon Seeps, Santa Barbara Channel, California

Science.gov (United States)

Mau, S.; Reed, J.; Clark, J.; Valentine, D.

2006-12-01

Large quantities of natural gas are emitted from the seafloor into the coastal ocean near Coal Oil Point, Santa Barbara Channel (SBC), California. Methane, ethane, and propane were quantified in the surface water at 79 stations in a 270 km2 area in order to map the surficial hydrocarbon plume and to quantify air-sea exchange of these gases. A time series was initiated for 14 stations to identify the variability of the mapped plume, and biologically-mediated oxidation rates of methane were measured to quantify the loss of methane in surface water. The hydrocarbon plume was found to comprise ~70 km2 and extended beyond study area. The plume width narrowed from 3 km near the source to 0.7 km further from the source, and then expanded to 6.7 km at the edge of the study area. This pattern matches the cyclonic gyre which is the normal current flow in this part of the Santa Barbara Channel - pushing water to the shore near the seep field and then broadening the plume while the water turns offshore further from the source. Concentrations of gaseous hydrocarbons decrease as the plume migrates. Time series sampling shows similar plume width and hydrocarbon concentrations when normal current conditions prevail. In contrast, smaller plume width and low hydrocarbon concentrations were observed when an additional anticyclonic eddy reversed the normal current flow, and a much broader plume with higher hydrocarbon concentrations was observed during a time of diminished speed within the current gyre. These results demonstrate that surface currents control hydrocarbon plume dynamics in the SBC, though hydrocarbon flux to the atmosphere is likely less dependent on currents. Estimates of air- sea hydrocarbon flux and biological oxidation rates will also be presented.

Reactor core of nuclear reactor

International Nuclear Information System (INIS)

Sasagawa, Masaru; Masuda, Hiroyuki; Mogi, Toshihiko; Kanazawa, Nobuhiro.

1994-01-01

In a reactor core, a fuel inventory at an outer peripheral region is made smaller than that at a central region. Fuel assemblies comprising a small number of large-diameter fuel rods are used at the central region and fuel assemblies comprising a great number of smalldiameter fuel rods are used at the outer peripheral region. Since a burning degradation rate of the fuels at the outer peripheral region can be increased, the burning degradation rate at the infinite multiplication factor of fuels at the outer region can substantially be made identical with that of the fuels in the inner region. As a result, the power distribution in the direction of the reactor core can be flattened throughout the entire period of the burning cycle. Further, it is also possible to make the degradation rate of fuels at the outer region substantially identical with that of fuels at the inner side. A power peak formed at the outer circumferential portion of the reactor core of advanced burning can be lowered to improve the fuel integrity, and also improve the reactor safety and operation efficiency. (N.H.)

Bacterial Community Response in Deep Faroe-Shetland Channel Sediments Following Hydrocarbon Entrainment With and Without Dispersant Addition

Directory of Open Access Journals (Sweden)

Luis J. Perez Calderon

2018-05-01

Full Text Available Deep sea oil exploration is increasing and presents environmental challenges for deep ocean ecosystems. Marine oil spills often result in contamination of sediments with oil; following the Deepwater Horizon (DwH disaster up to 31% of the released oil entrained in the water column was deposited as oily residues on the seabed. Although the aftermath of DwH was studied intensely, lessons learned may not be directly transferable to other deep-sea hydrocarbon exploration areas, such as the Faroe-Shetland Channel (FSC which comprises cold temperatures and a unique hydrodynamic regime. Here, transport of hydrocarbons into deep FSC sediments, subsequent responses in benthic microbial populations and effects of dispersant application on hydrocarbon fate and microbial communities were investigated. Sediments from 1,000 m in the FSC were incubated at 0°C for 71 days after addition of a 20-hydrocarbon component oil-sediment aggregate. Dispersant was added periodically from day 4. An additional set of cores using sterilized and homogenized sediment was analyzed to evaluate the effects of sediment matrix modification on hydrocarbon entrainment. Sediment layers were independently analyzed for hydrocarbon content by gas chromatography with flame ionization detection and modeled with linear mixed effects models. Oil was entrained over 4 cm deep into FSC sediments after 42 days and dispersant effectiveness on hydrocarbon removal from sediment to the water column decreased with time. Sterilizing and homogenizing sediment resulted in hydrocarbon transport over 4 cm into sediments after 7 days. Significant shifts in bacterial populations were observed (DGGE profiling in response to hydrocarbon exposure after 42 days and below 2 cm deep. Dispersant application resulted in an accelerated and modified shift in bacterial communities. Bacterial 16S rRNA gene sequencing of oiled sediments revealed dominance of Colwellia and of Fusibacter when dispersant was applied over

Petroleum hydrocarbons in offshore sediments from the Gulf

International Nuclear Information System (INIS)

Al-Lihaibi, S.S.; Al-Omran, Laila

1996-01-01

Petroleum hydrocarbons in offshore sediments from the central part of the Gulf were measured using fluorescence spectrophotometry. Concentrations varied between 4.0 and 56.2 μg/g wet sediment (expressed as Kuwait Crude Oil equivalents), with an average of 12.3 μ/g. Highest concentrations were recorded in the north-west sector, with concentrations decreasing in a south-westerly direction. No significant correlations were observed between petroleum hydrocarbons and sedimentary organic carbon (r-0.07), 'mud' content (r=0.09), 'sand' content (r= -0.08) or 'gravel' content (r= -0.12). Distributions of oil are considered to relate more closely to prevailing current and localized pollutant sources in the region. Despite the substantial inputs of oil to the Gulf, contamination can be considered comparatively low, possibly reflecting physical processes and biological degradation which accelerate removal of petroleum from this marine environment. (author)

Predicting hydrocarbon release from soil

International Nuclear Information System (INIS)

Poppendieck, D.; Loehr, R.C.

2002-01-01

'Full text:' The remediation of hazardous chemicals from soils can be a lengthy and costly process. As a result, recent regulatory initiatives have focused on risk-based corrective action (RBCA) approaches. Such approaches attempt to identify the amount of chemical that can be left at a site with contaminated soil and still be protective of human health and the environment. For hydrocarbons in soils to pose risk to human heath and the environment, the hydrocarbons must be released from the soil and accessible to microorganisms, earthworms, or other higher level organisms. The sorption of hydrocarbons to soil can reduce the availability of the hydrocarbon to receptors. Typically in soils and sediments, there is an initial fast release of a hydrocarbon from the soil to the aqueous phase followed by a slower release of the remaining hydrocarbon to the aqueous phase. The rate and extent of slow release can influence aqueous hydrocarbon concentrations and the fate and transport of hydrocarbons in the subsurface. Once the fast fraction of the chemical has been removed from the soil, the remaining fraction of a chemical may desorb at a rate that natural mechanisms can attenuate the released hydrocarbon. Hence, active remediation may be needed only until the fast fraction has been removed. However, the fast fraction is a soil and chemical specific parameter. This presentation will present a tier I type protocol that has been developed to quickly estimate the fraction of hydrocarbons that are readily released from the soil matrix to the aqueous phase. Previous research in our laboratory and elsewhere has used long-term desorption (four months) studies to determine the readily released fraction. This research shows that a single short-term (less than two weeks) batch extraction procedure provides a good estimate of the fast released fraction derived from long-term experiments. This procedure can be used as a tool to rapidly evaluate the release and bioavailability of

CHARACTERISTICS OF HYDROCARBON EXPLOITATION IN ARCTIC CIRCLE

Directory of Open Access Journals (Sweden)

Vanja Lež

2013-12-01

Full Text Available The existence of large quantities of hydrocarbons is supposed within the Arctic Circle. Assumed quantities are 25% of the total undiscovered hydrocarbon reserves on Earth, mostly natural gas. Over 500 major and minor gas accumulations within the Arctic Circle were discovered so far, but apart from Snøhvit gas field, there is no commercial exploitation of natural gas from these fields. Arctic gas projects are complicated, technically hard to accomplish, and pose a great threat to the return of investment, safety of people and equipment and for the ecosystem. Russia is a country that is closest to the realization of the Arctic gas projects that are based on the giant gas fields. The most extreme weather conditions in the seas around Greenland are the reason why this Arctic region is the least explored and furthest from the realization of any gas project (the paper is published in Croatian .

A chemical and biological study of the impact of a suspected oil seep at the coast of Marraat, Nuussuaq, Greenland. With a summary of other environmental studies of hydrocarbons in Greenland

Energy Technology Data Exchange (ETDEWEB)

Mosbech, A.; Hansen, Asger B.; Asmund, G.; Dahlloef, I.; Groth Petersen, D.; Strand, J.

2007-08-15

These studies were conducted on the Nuussuaq Peninsula at Marraat, where GEUS discovered oil in porous volcanics in the early 1990s. This oil was also found in the Marraat-1 core drilled in 1993. At Marraat the presence of oil stained stones scattered along the coast indicates oil bearing strata and the existence of potential oil seeps. The studies reported here had the objective to see, if the suspected seep had a local impact on the chemistry and biological communities in the marine environment at Marraat. The study included sediments, blue mussels and fish that were analyzed for hydrocarbons, a Pollution Induced Community Test (PICT), a sediment toxicity test and a measurement of PAH metabolites in fish gall. The hydrocarbon pattern found in sediment and biota samples indicates input from both immature petrogenic hydrocarbons of possible terrestrial origin and local pollution by fuel oil. But the hydrocarbon levels found were low and do not indicate an input from a natural local oil seep at Marraat. The results of the PICT, the sediment toxicity test and the PAH metabolite study do not either indicate the presence of an oil seep. However, compared to sediments from a larger area of West Greenland the sediments close to Nuussuaq and Disko have higher concentrations of PAH expressed on basis of their content of organic matter. This could be a result of natural seepage of oil in the Nuusuuaq/Disko region. (au)

Hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

1927-02-22

Coal tar, mineral oils, bitumens, coal extraction products, hydrogenation products of coal, oil schists can be atomized and heated with steam to decompose pyrogenetically and form gases rich in olefins which may be heated with or without pressure and with or without catalysts to produce liquid hydrocarbons of low boiling point, some of which may be aromatic. The apparatus should be lined with copper, silica, or ferrosilicon to prevent contact of the bases with iron which causes deposition of soot. Catalysts used may be metal oxides, silica, graphite, active charcoal, mica, pumice, porcelain, barium carbonate, copper, silver, gold, chromium, boron, or their compounds. At temperatures from 300 to 400/sup 0/C, olefins are produced. At higher temperatures, naphthenes and benzene hydrocarbons are produced.

Deep-water northern Gulf of Mexico hydrocarbon plays

International Nuclear Information System (INIS)

Peterson, R.H.; Cooke, D.W.

1995-01-01

The geologic setting in the deep-water (depths greater than 1,500 feet) Gulf of Mexico is very favorable for the existence of large, commercial hydrocarbon accumulations. These areas have active salt tectonics that create abundant traps, underlying mature Mesozoic source rocks that can be observed expelling oil and gas to the ocean surface, and good quality reservoirs provided by turbidite sand deposits. Despite the limited amount of drilling in the deep-water Gulf of Mexico, 11 deep-water accumulations have been discovered which, when developed, will rank in the top 100 largest fields in the Gulf of Mexico. Proved field discoveries (those with announced development plans) have added over 1 billion barrels of oil equivalent to Gulf of Mexico reserves, and unproved field discoveries may add to additional billion barrels of oil equivalent. The Minerals Management Service, United States Department of the Interior, has completed a gulf-wide review of over 1,086 oil and gas fields and placed every pay sand in each field into a hydrocarbon play (plays are defined by chronostratigraphy, lithostratigraph, structure, and production). Seven productive hydrocarbon plays were identified in the deep-water northern Gulf of Mexico. Regional maps illustrate the productive limits of each play. In addition, field data, dry holes, and wells with sub-economic pay were added to define the facies and structural limits for each play. Areas for exploration potential are identified for each hydrocarbon play. A type field for each play is chosen to demonstrate the play's characteristics

Fractional separation of hydrocarbon vapours

Energy Technology Data Exchange (ETDEWEB)

1937-07-10

A process is described for converting higher boiling hydrocarbons to lower boiling hydrocarbons by subjecting them at elevated temperatures to a conversion operation, then separating the higher and lower boiling fractions. The separation takes place while the reaction products are maintained in the vapor phase by contact with a mass of solid porous material which has little or no catalytic activity but does have a preferential absorption property for higher boiling hydrocarbons so that the lower boiling part of the reaction products pass through the separation zone while the heavier hydrocarbons are retained. The separation is accomplished without substantial loss of heat of these reaction products.

Sedimentary records of polycyclic aromatic hydrocarbons (PAHs) in remote lakes across the Tibetan Plateau.

Science.gov (United States)

Yang, Ruiqiang; Xie, Ting; Li, An; Yang, Handong; Turner, Simon; Wu, Guangjian; Jing, Chuanyong

2016-07-01

Sediment cores from five lakes across the Tibetan Plateau were used as natural archives to study the time trends of polycyclic aromatic hydrocarbons (PAHs). The depositional flux of PAHs generally showed an increasing trend from the deeper layers towards the upper layer sediments. The fluxes of PAHs were low with little variability before the 1950s, and then gradually increased to the late 1980s, with a faster increasing rate after the 1990s. This temporal pattern is clearly different compared with those remote lakes across the European mountains when PAHs started to decrease during the period 1960s-1980s. The difference of the temporal trend was attributed to differences in the economic development stages and energy structure between these regions. PAHs are dominated by the lighter 2&3-ring homologues with the averaged percentage over 87%, while it is notable that the percentage of heavier 4-6 ring PAHs generally increased in recent years, which suggests the contribution of local high-temperature combustion sources becoming more predominant. Copyright © 2016 Elsevier Ltd. All rights reserved.

Measurements of acetylene in air extracted from polar ice cores

Science.gov (United States)

Nicewonger, M. R.; Aydin, M.; Montzka, S. A.; Saltzman, E. S.

2016-12-01

Acetylene (ethyne) is a non-methane hydrocarbon emitted during combustion of fossil fuels, biofuels, and biomass. The major atmospheric loss pathway of acetylene is oxidation by hydroxyl radical with a lifetime estimated at roughly two weeks. The mean annual acetylene levels over Greenland and Antarctica are 250 ppt and 20 ppt, respectively. Firn air measurements suggest atmospheric acetylene is preserved unaltered in polar snow and firn. Atmospheric reconstructions based on firn air measurements indicate acetylene levels rose significantly during the twentieth century, peaked near 1980, then declined to modern day levels. This historical trend is similar to that of other fossil fuel-derived non-methane hydrocarbons. In the preindustrial atmosphere, acetylene levels should primarily reflect emissions from biomass burning. In this study, we present the first measurements of acetylene in preindustrial air extracted from polar ice cores. Air from fluid and dry-drilled ice cores from Summit, Greenland and WAIS-Divide Antarctica is extracted using a wet-extraction technique. The ice core air is analyzed using gas chromatography and high-resolution mass spectrometry. Between 1400 to 1800 C.E., acetylene levels over Greenland and Antarctica varied between roughly 70-120 ppt and 10-30 ppt, respectively. The preindustrial Greenland acetylene levels are significantly lower than modern levels, reflecting the importance of northern hemisphere fossil fuel sources today. The preindustrial Antarctic acetylene levels are comparable to modern day levels, indicating similar emissions in the preindustrial atmosphere, likely from biomass burning. The implications of the preindustrial atmospheric acetylene records from both hemispheres will be discussed.

Picosecond pulse radiolysis studies on geminate ion recombination in saturated hydrocarbon

International Nuclear Information System (INIS)

Tagawa, S.; Washio, M.; Kobayashi, H.; Katsumura, Y.; Tabata, Y.

1983-01-01

The geminate recombination kinetics of the excess electron and the electron hole are discussed, based on time-resolved data on picosecond and nanosecond time scales. The recombination times of the excess electron and the electron hole are evaluated to be 3 ps for cyclohexane on the basis of the comparison between the experimental and the calculated results. The spin correlation decay of the geminate ion pairs and the triplet state formation before the spin correlation loss have also been discussed. The rapidly decaying species with very broad absorption spectra, which are similar to the absorption spectra of the cation radicals of saturated hydrocarbons, have been observed in neat saturated hydrocarbons in the sub-nanosecond and a few nanosecond time regions. The identification of the rapidly decaying species were not definitely made but those species are tentatively assigned to the excited states and/or the tail of the geminate cation radicals of saturated hydrocarbons. (author)

A second hydrocarbon boom threatens the Peruvian Amazon: trends, projections, and policy implications

Energy Technology Data Exchange (ETDEWEB)

Finer, Matt [Save America' s Forests, 4 Library Court NW, Washington, DC 20003 (United States); Orta-Martinez, Marti, E-mail: matt@saveamericasforests.or, E-mail: martiorta@gmail.co [Institut de Ciencia i Tecnologia Ambiental, Universitat Autonoma de Barcelona, 08193 Bellaterra (Barcelona) (Spain)

2010-01-15

The Peruvian Amazon is home to extraordinary biological and cultural diversity, and vast swaths of this mega-diverse region remain largely intact. Recent analysis indicates, however, that the rapid proliferation of oil and gas exploration zones now threatens the region's biodiversity, indigenous peoples, and wilderness areas. To better elucidate this dynamic situation, we analyzed official Peruvian government hydrocarbon information and generated a quantitative analysis of the past, present, and future of oil and gas activities in the Peruvian Amazon. We document an extensive hydrocarbon history for the region-over 104 000 km of seismic lines and 679 exploratory and production wells-highlighted by a major exploration boom in the early 1970s. We show that an unprecedented 48.6% of the Peruvian Amazon has been recently covered by oil and gas concessions, up from just 7.1% in 2003. These oil and gas concessions overlap 17.1% of the Peruvian Amazon protected area system and over half of all titled indigenous lands. Moreover, we found that up to 72% of the Peruvian Amazon has been zoned for hydrocarbon activities (concessions plus technical evaluation agreements and proposed concessions) in the past two years, and over 84% at some point during the past 40 years. We project that the recent rapid proliferation of hydrocarbon zones will lead to a second exploration boom, characterized by over 20 000 km of new seismic testing and construction of over 180 new exploratory wells in remote, intact, and sensitive forest areas. As the Peruvian Amazon oil frontier rapidly expands, we conclude that a rigorous policy debate is urgently needed in order to avoid the major environmental impacts associated with the first exploration boom of the 1970s and to minimize the social conflict that recently led to deadly encounters between indigenous protesters and government forces.

A second hydrocarbon boom threatens the Peruvian Amazon: trends, projections, and policy implications

International Nuclear Information System (INIS)

Finer, Matt; Orta-Martinez, Marti

2010-01-01

The Peruvian Amazon is home to extraordinary biological and cultural diversity, and vast swaths of this mega-diverse region remain largely intact. Recent analysis indicates, however, that the rapid proliferation of oil and gas exploration zones now threatens the region's biodiversity, indigenous peoples, and wilderness areas. To better elucidate this dynamic situation, we analyzed official Peruvian government hydrocarbon information and generated a quantitative analysis of the past, present, and future of oil and gas activities in the Peruvian Amazon. We document an extensive hydrocarbon history for the region-over 104 000 km of seismic lines and 679 exploratory and production wells-highlighted by a major exploration boom in the early 1970s. We show that an unprecedented 48.6% of the Peruvian Amazon has been recently covered by oil and gas concessions, up from just 7.1% in 2003. These oil and gas concessions overlap 17.1% of the Peruvian Amazon protected area system and over half of all titled indigenous lands. Moreover, we found that up to 72% of the Peruvian Amazon has been zoned for hydrocarbon activities (concessions plus technical evaluation agreements and proposed concessions) in the past two years, and over 84% at some point during the past 40 years. We project that the recent rapid proliferation of hydrocarbon zones will lead to a second exploration boom, characterized by over 20 000 km of new seismic testing and construction of over 180 new exploratory wells in remote, intact, and sensitive forest areas. As the Peruvian Amazon oil frontier rapidly expands, we conclude that a rigorous policy debate is urgently needed in order to avoid the major environmental impacts associated with the first exploration boom of the 1970s and to minimize the social conflict that recently led to deadly encounters between indigenous protesters and government forces.

Reconstruction of pollution history of organic contaminants in the upper Gulf of Thailand by using sediment cores: first report from Tropical Asia Core (TACO) project.

Science.gov (United States)

Boonyatumanond, Ruchaya; Wattayakorn, Gullaya; Amano, Atsuko; Inouchi, Yoshio; Takada, Hideshige

2007-05-01

This paper reports the first reconstruction of a pollution history in tropical Asia from sediment cores. Four sediment core samples were collected from an offshore transect in the upper Gulf of Thailand and were analyzed for organic micropollutants. The cores were dated by measurement of (137)Cs and geochronometric molecular markers (linear alkylbenzenes, LABs; and tetrapropylene-type alkylbenzenes, TABs). Polychlorinated biphenyl (PCB) concentrations showed a subsurface maximum in layers corresponding to the 1970s, indicating the effectiveness of regulation of PCBs in Thailand. LAB concentrations increased over time, indicating the increase in input of sewage into the Gulf during the last 30 years. Hopanes, biomarkers of petroleum pollution, also increased over time, indicating that the inputs of automobile-derived hydrocarbons to the coastal zone has been increasing owing to the increased number of cars in Thailand since the 1950s. Polycyclic aromatic hydrocarbons (PAHs) increased in the layers corresponding to the 1950s and 1960s, probably because of the increased inputs of automobile-derived PAHs. PAH concentrations in the upper layers corresponding to the 1970s and later remained constant or increased. The absence of a subsurface maximum of PAHs contrasts with results observed in industrialized countries. This can be explained by the facts that the Thai economy did not depend on coal as an energy source in the 1960s and that economic growth has continued since the 1970s to the present. The deposition flux of PAHs and hopanes showed a dramatic offshore decrease, whereas that of LABs was uniform.

Reconstruction of pollution history of organic contaminants in the upper Gulf of Thailand by using sediment cores: First report from Tropical Asia Core (TACO) project

International Nuclear Information System (INIS)

Boonyatumanond, Ruchaya; Wattayakorn, Gullaya; Amano, Atsuko; Inouchi, Yoshio; Takada, Hideshige

2007-01-01

This paper reports the first reconstruction of a pollution history in tropical Asia from sediment cores. Four sediment core samples were collected from an offshore transect in the upper Gulf of Thailand and were analyzed for organic micropollutants. The cores were dated by measurement of 137 Cs and geochronometric molecular markers (linear alkylbenzenes, LABs; and tetrapropylene-type alkylbenzenes, TABs). Polychlorinated biphenyl (PCB) concentrations showed a subsurface maximum in layers corresponding to the 1970s, indicating the effectiveness of regulation of PCBs in Thailand. LAB concentrations increased over time, indicating the increase in input of sewage into the Gulf during the last 30 years. Hopanes, biomarkers of petroleum pollution, also increased over time, indicating that the inputs of automobile-derived hydrocarbons to the coastal zone has been increasing owing to the increased number of cars in Thailand since the 1950s. Polycyclic aromatic hydrocarbons (PAHs) increased in the layers corresponding to the 1950s and 1960s, probably because of the increased inputs of automobile-derived PAHs. PAH concentrations in the upper layers corresponding to the 1970s and later remained constant or increased. The absence of a subsurface maximum of PAHs contrasts with results observed in industrialized countries. This can be explained by the facts that the Thai economy did not depend on coal as an energy source in the 1960s and that economic growth has continued since the 1970s to the present. The deposition flux of PAHs and hopanes showed a dramatic offshore decrease, whereas that of LABs was uniform

Removal of hydrocarbon from refinery tank bottom sludge employing microbial culture.

Science.gov (United States)

Saikia, Rashmi Rekha; Deka, Suresh

2013-12-01

Accumulation of oily sludge is becoming a serious environmental threat, and there has not been much work reported for the removal of hydrocarbon from refinery tank bottom sludge. Effort has been made in this study to investigate the removal of hydrocarbon from refinery sludge by isolated biosurfactant-producing Pseudomonas aeruginosa RS29 strain and explore the biosurfactant for its composition and stability. Laboratory investigation was carried out with this strain to observe its efficacy of removing hydrocarbon from refinery sludge employing whole bacterial culture and culture supernatant to various concentrations of sand-sludge mixture. Removal of hydrocarbon was recorded after 20 days. Analysis of the produced biosurfactant was carried out to get the idea about its stability and composition. The strain could remove up to 85 ± 3 and 55 ± 4.5 % of hydrocarbon from refinery sludge when whole bacterial culture and culture supernatant were used, respectively. Maximum surface tension reduction (26.3 mN m(-1)) was achieved with the strain in just 24 h of time. Emulsification index (E24) was recorded as 100 and 80 % with crude oil and n-hexadecane, respectively. The biosurfactant was confirmed as rhamnolipid containing C8 and C10 fatty acid components and having more mono-rhamnolipid congeners than the di-rhamnolipid ones. The biosurfactant was stable up to 121 °C, pH 2-10, and up to a salinity value of 2-10 % w/v. To our knowledge, this is the first report showing the potentiality of a native strain from the northeast region of India for the efficient removal of hydrocarbon from refinery sludge.

Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site

Energy Technology Data Exchange (ETDEWEB)

Akbari, Ali; Ghoshal, Subhasis, E-mail: subhasis.ghoshal@mcgill.ca

2014-09-15

Highlights: • Aeration and moisture addition alone caused extensive hydrocarbon biodegradation. • 30-day slurry reactor remediation endpoints attained in 385 days in biopiles. • High nitrogen concentrations inhibited hydrocarbon degradation. • Inhibition of biodegradation linked to lack of shifts in soil microbial community. - Abstract: Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16–C34) in a pilot-scale biopile experiment conducted at 15 °C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16–C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day{sup −1} in biopile tank compared to 0.11 day{sup −1} in slurry bioreactors for C16–C34 hydrocarbons, the biodegradation extents for this fraction

EXTINCTION AND POLYCYCLIC AROMATIC HYDROCARBON INTENSITY VARIATIONS ACROSS THE H II REGION IRAS 12063-6259

Energy Technology Data Exchange (ETDEWEB)

Stock, D. J.; Peeters, E.; Otaguro, J. N. [Department of Physics and Astronomy, University of Western Ontario, London, ON N6A 3K7 (Canada); Tielens, A. G. G. M. [Leiden Observatory, Leiden University, P.O. Box 9513, NL-2300 RA Leiden (Netherlands); Bik, A. [Max-Planck-Institut fuer Astronomie, Koenigstuhl 17, D-69117 Heidelberg (Germany)

2013-07-01

The spatial variations in polycyclic aromatic hydrocarbon (PAH) band intensities are normally attributed to the physical conditions of the emitting PAHs, however in recent years it has been suggested that such variations are caused mainly by extinction. To resolve this question, we have obtained near-infrared (NIR), mid-infrared (MIR), and radio observations of the compact H II region IRAS 12063-6259. We use these data to construct multiple independent extinction maps and also to measure the main PAH features (6.2, 7.7, 8.6, and 11.2 {mu}m) in the MIR. Three extinction maps are derived: the first using the NIR hydrogen lines and case B recombination theory; the second combining the NIR data with radio data; and the third making use of the Spitzer/IRS MIR observations to measure the 9.8 {mu}m silicate absorption feature using the Spoon method and PAHFIT (as the depth of this feature can be related to overall extinction). The silicate absorption over the bright, southern component of IRAS 12063-6259 is almost absent while the other methods find significant extinction. While such breakdowns of the relationship between the NIR extinction and the 9.8 {mu}m absorption have been observed in molecular clouds, they have never been observed for H II regions. We then compare the PAH intensity variations in the Spitzer/IRS data after dereddening to those found in the original data. It was found that in most cases, the PAH band intensity variations persist even after dereddening, implying that extinction is not the main cause of the PAH band intensity variations.

Polycyclic aromatic hydrocarbons and risk elements in honey from the South Moravian region (Czech Republic

Directory of Open Access Journals (Sweden)

Petra Batelková

2012-01-01

Full Text Available The aim of this study was to determine the actual content of some exogenous contaminants in the honey from the South Moravian region of the Czech Republic. The content of polycyclic aromatic hydrocarbons (PAHs and risk elements (Mercury - Hg, Cadmium - Cd, Lead - Pb, and Arsenic - As in multifloral blossom and honey dew samples of honey were determined by high-performance liquid chromatography and atomic absorption spectroscopy methods. The samples were collected form beekeepers and from retail stores located in South Moravia in the Czech Republic. Concentrations of individual PAHs in honey samples ranged between 0.02 μg·kg-1–1.93 μg·kg-1. The limit of benzo[a]pyrene for infant formula (1.0 μg·kg-1 was not exceeded and fluoranthene was not quantified in any of the samples. Concentrations of Hg, Cd, and Pb were in the range of 3.24 μg·kg-1–11.31 μg·kg-1, 0.95 μg·kg-1–32.35 μg·kg-1, and 22.80 μg·kg-1–177.85 μg·kg-1, respectively. Concentration of As exceeded the detection limit only in three samples, ranging from 3.51 μg·kg-1 to 4.35 μg·kg-1. Acceptable limits for trace elements in infant formula were met. Results of this study complete present knowledge of the contaminant content in Czech honey and confirmed high quality and safety of honey from the South Moravian region.

The effects of Hurricanes Katrina and Rita on seabed polycyclic aromatic hydrocarbon dynamics in the Gulf of Mexico.

Science.gov (United States)

Mitra, Siddhartha; Lalicata, Joseph J; Allison, Mead A; Dellapenna, Timothy M

2009-06-01

To assess the extent to which Hurricanes Katrina and Rita affected polycyclic aromatic hydrocarbons (PAH) in the Gulf of Mexico (GOM), sediment cores were analyzed in late 2005 from: a shallow shelf, a deeper shelf, and a marsh station. Sediment geochronology, fabric, and geochemistry show that the 2005 storms deposited approximately 10cm of sediment to the surface of a core at 5-12A. Bulk carbon geochemistry and PAH isomers in this top layer suggest that the source of sediment to the top portion of core 5-12A was from a relatively more marine area. Particulate PAHs in the marsh core (04M) appeared unaffected by the storms while sediments in the core from Station 5-1B (deeper shelf) were affected minimally (some possible storm-derived deposition). Substantial amounts of PAH-laden particles may have been displaced from the seabed in shallow areas of the water column in the GOM by these 2005 storms.

Bioremediation of soils containing petroleum hydrocarbons, chlorinated phenols, and polycyclic aromatic hydrocarbons

International Nuclear Information System (INIS)

Seech, A.; Burwell, S.; Marvan, I.

1994-01-01

Bench-scale treatability investigations, pilot-scale and full-scale bioremediation projects were conducted to evaluate Daramend trademark bioremediation of soils containing petroleum hydrocarbons, heavy oils, paraffins, chlorinated phenols and polycyclic aromatic hydrocarbons (PAHs). Bench-scale investigations were conducted using glass microcosms. Pilot-scale and full-scale demonstrations were conducted at industrial sites and included treatment of excavated soils and sediments in on-site cells constructed using synthetic liners and covered by steel/polyethylene structures as well as in-situ treatment. A total of approximately 5,000 tons of soil was treated. The soil treatment included organic soil amendments, specialized tillage/aeration apparatus, and strict control of soil moisture. The amendments are composed of naturally-occurring organic materials prepared to soil-specific particle size distributions, nutrient profiles, and nutrient-release kinetics. Bench-scale work indicated that in refinery soil containing high concentrations of heavy oils, extractable hydrocarbon concentrations could be rapidly reduced to industrial clean-up criteria, and that the hydrocarbons were fully mineralized with release of CO 2

Characterization of hydrocarbon utilizing fungi from hydrocarbon ...

African Journals Online (AJOL)

Prof. Ogunji

isolated fungi could be useful in the bioremediation of hydrocarbon polluted sites. Keywords: ... Technologies such as mechanical force, burying, evaporation, dispersant application, and ..... The effects of drilling fluids on marine bacteria from a.

Intrinsic Connections of the Core Auditory Cortical Regions and Rostral Supratemporal Plane in the Macaque Monkey.

Science.gov (United States)

Scott, Brian H; Leccese, Paul A; Saleem, Kadharbatcha S; Kikuchi, Yukiko; Mullarkey, Matthew P; Fukushima, Makoto; Mishkin, Mortimer; Saunders, Richard C

2017-01-01

In the ventral stream of the primate auditory cortex, cortico-cortical projections emanate from the primary auditory cortex (AI) along 2 principal axes: one mediolateral, the other caudorostral. Connections in the mediolateral direction from core, to belt, to parabelt, have been well described, but less is known about the flow of information along the supratemporal plane (STP) in the caudorostral dimension. Neuroanatomical tracers were injected throughout the caudorostral extent of the auditory core and rostral STP by direct visualization of the cortical surface. Auditory cortical areas were distinguished by SMI-32 immunostaining for neurofilament, in addition to established cytoarchitectonic criteria. The results describe a pathway comprising step-wise projections from AI through the rostral and rostrotemporal fields of the core (R and RT), continuing to the recently identified rostrotemporal polar field (RTp) and the dorsal temporal pole. Each area was strongly and reciprocally connected with the areas immediately caudal and rostral to it, though deviations from strictly serial connectivity were observed. In RTp, inputs converged from core, belt, parabelt, and the auditory thalamus, as well as higher order cortical regions. The results support a rostrally directed flow of auditory information with complex and recurrent connections, similar to the ventral stream of macaque visual cortex. Published by Oxford University Press 2015. This work is written by (a) US Government employee(s) and is in the public domain in the US.

World-wide and regional intercomparison for the determination of organochlorine compounds and petroleum hydrocarbons in sediment sample IAEA-357. Report no. 51

International Nuclear Information System (INIS)

Villeneuve, J.P.; Mee, L.D.

1992-06-01

This report describes the results of IAEA/UNEP intercomparison run 357 for the chemical analysis of organochlorine compounds and petroleum hydrocarbons in marine sediments. The Marine Environmental Studies Laboratory (MESL) of IAEA-MEL has conducted intercomparison exercises on trace organic compounds for over ten years as part of its contribution to IAEA's analytical quality control service and UNEP's regional seas programme and occasionally in association with the intergovernmental oceanographic Commission (of UNESCO) GIPME programme. Results of previous exercises have revealed serious problems for many regional laboratories to obtain comparable data. This, in turn, has raised serious concerns on the validity of region-wide or global marine pollution assessments. Even more worrisome was the apparent lack of improvement in data quality from exercise to exercise. As a consequence of the above situation, it was decided to seek increased support for quality assurance programmes. Staff of MESL, with funding from UNEP, the World bank and regional trust funds, embarked on a campaign to train analysts in modern measurement techniques, supply appropriate and reliable reference methods and materials and, where possible, to improve analytical instruments in member states laboratories. This work continues at present and recent training programmes have been conducted in the Wider Caribbean, East Africa, The Gulf and the Mediterranean

Measuring Trace Hydrocarbons in Silanes

Science.gov (United States)

Lesser, L. A.

1984-01-01

Technique rapid and uses standard analytical equipment. Silane gas containing traces of hydrocarbons injected into carrier gas of moist nitrogen having about 0.2 percent water vapor. Carrier, water and silane pass through short column packed with powdered sodium hydroxide which combines moisture and silane to form nonvolatile sodium silicate. Carrier gas free of silane but containing nonreactive hydrocarbons, pass to silica-gel column where chromatographic separation takes place. Hydrocarbons measured by FID.

Soil Iodine Determination in Deccan Syneclise, India: Implications for Near Surface Geochemical Hydrocarbon Prospecting

International Nuclear Information System (INIS)

Mani, Devleena; Kumar, T. Satish; Rasheed, M. A.; Patil, D. J.; Dayal, A. M.; Rao, T. Gnaneshwar; Balaram, V.

2011-01-01

The association of iodine with organic matter in sedimentary basins is well documented. High iodine concentration in soils overlying oil and gas fields and areas with hydrocarbon microseepage has been observed and used as a geochemical exploratory tool for hydrocarbons in a few studies. In this study, we measure iodine concentration in soil samples collected from parts of Deccan Syneclise in the west central India to investigate its potential application as a geochemical indicator for hydrocarbons. The Deccan Syneclise consists of rifted depositional sites with Gondwana–Mesozoic sediments up to 3.5 km concealed under the Deccan Traps and is considered prospective for hydrocarbons. The concentration of iodine in soil samples is determined using ICP-MS and the values range between 1.1 and 19.3 ppm. High iodine values are characteristic of the northern part of the sampled region. The total organic carbon (TOC) content of the soil samples range between 0.1 and 1.3%. The TOC correlates poorly with the soil iodine (r 2 < 1), indicating a lack of association of iodine with the surficial organic matter and the possibility of interaction between the seeping hydrocarbons and soil iodine. Further, the distribution pattern of iodine compares well with two surface geochemical indicators: the adsorbed light gaseous hydrocarbons (methane through butane) and the propane-oxidizing bacterial populations in the soil. The integration of geochemical observations show the occurrence of elevated values in the northern part of the study area, which is also coincident with the presence of exposed dyke swarms that probably serve as conduits for hydrocarbon microseepage. The corroboration of iodine with existing geological, geophysical, and geochemical data suggests its efficacy as one of the potential tool in surface geochemical exploration of hydrocarbons. Our study supports Deccan Syneclise to be promising in terms of its hydrocarbon prospects.

Structural Characterization of Core Region in Erwinia amylovora Lipopolysaccharide

Directory of Open Access Journals (Sweden)

Angela Casillo

2017-03-01

Full Text Available Erwinia amylovora (E. amylovora is the first bacterial plant pathogen described and demonstrated to cause fire blight, a devastating plant disease affecting a wide range of species including a wide variety of Rosaceae. In this study, we reported the lipopolysaccharide (LPS core structure from E. amylovora strain CFBP1430, the first one for an E. amylovora highly pathogenic strain. The chemical characterization was performed on the mutants waaL (lacking only the O-antigen LPS with a complete LPS-core, wabH and wabG (outer-LPS core mutants. The LPSs were isolated from dry cells and analyzed by means of chemical and spectroscopic methods. In particular, they were subjected to a mild acid hydrolysis and/or a hydrazinolysis and investigated in detail by one and two dimensional Nuclear Magnetic Resonance (NMR spectroscopy and ElectroSpray Ionization Fourier Transform-Ion Cyclotron Resonance (ESI FT-ICR mass spectrometry.

Natural gas treatment: Simultaneous water and hydrocarbon-dew point-control

Energy Technology Data Exchange (ETDEWEB)

Schmidt, T. (Solvay Catalysts GmbH, Hannover (Germany)); Rennemann, D. (Solvay Catalysts GmbH, Hannover (Germany)); Schulz, T. (Solvay Catalysts GmbH, Hannover (Germany))

1993-10-01

Natural gas is a multicomponent mixture of hydrocarbons. The condensation behavior of such mixtures is different from single component systems. The so-called retrograde behavior leads to the observations that saturated vapor (dew point curve) and saturated liquid curve (bubble point curve) are not identical. Between both is a region of saturated phases which even can exist above the critical point. Following this behaviour it is possible that condensation might occur at pressure decrease or at temperature increase, respectively. This phenomenon is undesired in natural gas pipeline networks. Selective removal of higher hydrocarbons by the means of adsorption can change the phase behavior in such a way that condensation does not occur at temperatures and pressures specified for gas distribution. (orig.)

TMI-2 core boring machine

International Nuclear Information System (INIS)

Croft, K.M.; Helbert, H.J.; Laney, W.M.

1986-01-01

An important and essential aspect of the TMI-2 defueling effort is to determine what occurred in the core region during the accident. Remote cameras and probes only portray a portion of the overall picture. What lies beneath the rubble bed and solidified sublayer is, as yet, unknown. This paper discusses the TMI-2 Core Boring Machine, which has been developed to drill into the damaged core of the TMI-2 reactor and extract stratified samples of the core. This machine, its unique support structure, positioning and leveling systems, and specially designed drill bits, combine to provide a unique mechanical system. In addition, the machine is controlled by a microprocessor; which actually controls the drilling operation, allowing relatively inexperienced operators to drill the core samples. A data acquisition system is data integral with the controlling system and collects data relative to system conditions and monitored parameters during drilling. Data obtained during the actual drilling operations are collected in a data base which will be used for actual mapping of the core region, identifying materials and stratification levels that are present

Purifying hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Rostin, H

1938-08-11

A process is described for continuously purifying hydrocarbon oils consisting in conducting the vapors of the same at a temperature of 300 to 400/sup 0/C over the oelitic ore minette together with reducing gases in presence of steam the proportion of the reducing gases and steam being such that the sulfur of the hydrocarbons escapes from the reaction chamber in the form of sulfuretted hydrogen without permanent sulfide of iron being formed.

Interseasonal movements of greater sage-grouse, migratory behavior, and an assessment of the core regions concept in Wyoming

Science.gov (United States)

Fedy, Bradley C.; Aldridge, Cameron L.; Doherty, Kevin E.; O'Donnell, Michael S.; Beck, Jeffrey L.; Bedrosian, Bryan; Holloran, Matthew J.; Johnson, Gregory D.; Kaczor, Nicholas W.; Kirol, Christopher P.; Mandich, Cheryl A.; Marshall, David; McKee, Gwyn; Olson, Chad; Swanson, Christopher C.; Walker, Brett L.

2012-01-01

Animals can require different habitat types throughout their annual cycles. When considering habitat prioritization, we need to explicitly consider habitat requirements throughout the annual cycle, particularly for species of conservation concern. Understanding annual habitat requirements begins with quantifying how far individuals move across landscapes between key life stages to access required habitats. We quantified individual interseasonal movements for greater sage-grouse (Centrocercus urophasianus; hereafter sage-grouse) using radio-telemetry spanning the majority of the species distribution in Wyoming. Sage-grouse are currently a candidate for listing under the United States Endangered Species Act and Wyoming is predicted to remain a stronghold for the species. Sage-grouse use distinct seasonal habitats throughout their annual cycle for breeding, brood rearing, and wintering. Average movement distances in Wyoming from nest sites to summer-late brood-rearing locations were 8.1 km (SE = 0.3 km; n = 828 individuals) and the average subsequent distances moved from summer sites to winter locations were 17.3 km (SE = 0.5 km; n = 607 individuals). Average nest-to-winter movements were 14.4 km (SE = 0.6 km; n = 434 individuals). We documented remarkable variation in the extent of movement distances both within and among sites across Wyoming, with some individuals remaining year-round in the same vicinity and others moving over 50 km between life stages. Our results suggest defining any of our populations as migratory or non-migratory is innappropriate as individual strategies vary widely. We compared movement distances of birds marked using Global Positioning System (GPS) and very high frequency (VHF) radio marking techniques and found no evidence that the heavier GPS radios limited movement. Furthermore, we examined the capacity of the sage-grouse core regions concept to capture seasonal locations. As expected, we found the core regions approach, which was

Can hydrocarbons entrapped in seep carbonates serve as gas geochemistry recorder?

Science.gov (United States)

Blumenberg, Martin; Pape, Thomas; Seifert, Richard; Bohrmann, Gerhard; Schlömer, Stefan

2018-04-01

The geochemistry of seep gases is useful for an understanding of the local petroleum system. Here it was tested whether individual light hydrocarbons in seep gases are representatively entrapped in authigenic carbonates that formed near active seep sites. If applicable, it would be possible to extract geochemical information not only on the origin but also on the thermal maturity of the hydrocarbon source rocks from the gases entrapped in carbonates in the past. Respective data could be used for a better understanding of paleoenvironments and might directly serve as calibration point for, amongst others, petroleum system modeling. For this approach, (sub)-recent seep carbonates from the Black Sea (Paleodnjepr region and Batumi seep area), two sites of the Campeche Knoll region in the Gulf of Mexico, and the Venere mud volcano (Mediterranean Sea) were selected. These seep carbonates derive from sites for which geochemical data on the currently seeping gases exist. During treatment with phosphoric acid, methane and higher hydrocarbons were released from all carbonates, but in low concentrations. Compositional studies demonstrate that the ratio of methane to the sum of higher hydrocarbons (C1/(C2+C3)) is (partly strongly) positively biased in the entrapped gas fraction. δ13C values of C1 were determined for all samples and, for the samples from the Gulf of Mexico and the Mediterranean Sea, also of C2 and C3. The present dataset from six seep sites indicates that information on the seeped methane can be—although with a scatter of several permil—recorded in seep carbonate matrices, but other valuable information like the composition and δ13C of ethane and propane appears to be modified or lost during, for example, enclosure or at an early stage of diagenesis.

Recovering low-boiling hydrocarbons, etc

Energy Technology Data Exchange (ETDEWEB)

Pier, M

1934-10-03

A process is described for the recovery of low-boiling hydrocarbons of the nature of benzine through treatment of liquid carbonaceous materials with hydrogen under pressure at raised temperature, suitably in the presence of catalysts. Middle oils (practically saturated with hydrogen) or higher boiling oils at a temperature above 500/sup 0/ (with or without the addition of hydrogen) containing cyclic hydrocarbons not saturated with hydrogen are changed into low boiling hydrocarbons of the nature of benzine. The cracking takes place under strongly hydrogenating conditions (with the use of a strongly active hydrogenating catalyst or high pressure) at temperatures below 500/sup 0/. If necessary, the constituents boiling below 200/sup 0/ can be reconverted into cyclic hydrocarbons partially saturated with hydrogen. (BLM)

Bioavailability enhanced rhizosphere remediation of petroleum hydrocarbon contaminated soil

International Nuclear Information System (INIS)

Marchenko, A.; Vorobyov, A.; Zharikov, G.; Ermolenko, Z.; Dyadishchev, N.; Borovick, R.; Sokolov, M.; Ortega-Calvo, J.J.

2005-01-01

Aliphatic, aromatic and polycyclic aromatic oil hydrocarbons are structurally complicated man-caused pollutants that are constantly brought into biosphere. Oil production in Russia, so as all over the world, is connected with pollution of biotopes, ecosystems and agro-landscapes. Presently large funds are allocated either for oil leak prevention or for discharged oil gathering. At the same time, in spite of large necessity in technologies for efficient reconstruction of soil bio-productivity, reliable regional systems of their remediation in situ have not been developed yet. One such method is rhizosphere remediation, a biotechnology, based on the functioning of plant-microbial complexes. Little is known about bioavailability in phyto-remediation systems. Specific bioavailability-promoting mechanisms, operating in soil with hydrocarbon-degrading populations, may be responsible for increased rates of pollutant transformation (increased bacterial adherence to the pollutants, production of bio-surfactants by bacteria or by plants, possible role of chemotaxis). In the course of work collection of 42 chemo-tactically active bio-surfactant producing strain-degraders of petroleum hydrocarbons including polycyclic aromatic hydrocarbons (PAHs) was created. Two representative strains were selected for detailed chemotaxis studies with PAHs (naphthalene, phenanthrene, anthracene, and pyrene), bacterial lipopolysaccharide and root exudates from seven different plants. These strains are produce the bio-surfactants (rhamno-lipid). The chemotactic response was quantified with a capillary and densitometric chemotaxis assay. Surface tension of cultural liquid was measured after cultivation of strains in the presence of hexadecane or phenanthrene with the use of a ring tensiometer. Before measuring of surface tension microbial cells were collected from liquid culture by centrifugation. Total petroleum Hydrocarbons (TPH) in soil were analyzed by infra-red spectroscopy method. PAHs

Bioavailability enhanced rhizosphere remediation of petroleum hydrocarbon contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Marchenko, A.; Vorobyov, A.; Zharikov, G.; Ermolenko, Z.; Dyadishchev, N.; Borovick, R.; Sokolov, M. [Research Centre for Toxicology and Hygienic Regulation of Biopreparations, Moscow region (Russian Federation); Ortega-Calvo, J.J. [Instituto de Recursos Naturales y Agrobiologia, CSIC, Sevilla (Spain)

2005-07-01

Aliphatic, aromatic and polycyclic aromatic oil hydrocarbons are structurally complicated man-caused pollutants that are constantly brought into biosphere. Oil production in Russia, so as all over the world, is connected with pollution of biotopes, ecosystems and agro-landscapes. Presently large funds are allocated either for oil leak prevention or for discharged oil gathering. At the same time, in spite of large necessity in technologies for efficient reconstruction of soil bio-productivity, reliable regional systems of their remediation in situ have not been developed yet. One such method is rhizosphere remediation, a biotechnology, based on the functioning of plant-microbial complexes. Little is known about bioavailability in phyto-remediation systems. Specific bioavailability-promoting mechanisms, operating in soil with hydrocarbon-degrading populations, may be responsible for increased rates of pollutant transformation (increased bacterial adherence to the pollutants, production of bio-surfactants by bacteria or by plants, possible role of chemotaxis). In the course of work collection of 42 chemo-tactically active bio-surfactant producing strain-degraders of petroleum hydrocarbons including polycyclic aromatic hydrocarbons (PAHs) was created. Two representative strains were selected for detailed chemotaxis studies with PAHs (naphthalene, phenanthrene, anthracene, and pyrene), bacterial lipopolysaccharide and root exudates from seven different plants. These strains are produce the bio-surfactants (rhamno-lipid). The chemotactic response was quantified with a capillary and densitometric chemotaxis assay. Surface tension of cultural liquid was measured after cultivation of strains in the presence of hexadecane or phenanthrene with the use of a ring tensiometer. Before measuring of surface tension microbial cells were collected from liquid culture by centrifugation. Total petroleum Hydrocarbons (TPH) in soil were analyzed by infra-red spectroscopy method. PAHs

Hydrous pyrolysis/oxidation process for in situ destruction of chlorinated hydrocarbon and fuel hydrocarbon contaminants in water and soil

Science.gov (United States)

Knauss, Kevin G.; Copenhaver, Sally C.; Aines, Roger D.

2000-01-01

In situ hydrous pyrolysis/oxidation process is useful for in situ degradation of hydrocarbon water and soil contaminants. Fuel hydrocarbons, chlorinated hydrocarbons, polycyclic aromatic hydrocarbons, petroleum distillates and other organic contaminants present in the soil and water are degraded by the process involving hydrous pyrolysis/oxidation into non-toxic products of the degradation. The process uses heat which is distributed through soils and water, optionally combined with oxygen and/or hydrocarbon degradation catalysts, and is particularly useful for remediation of solvent, fuel or other industrially contaminated sites.

Core Promoter Structure in the Oomycete Phytophthora infestans

Science.gov (United States)

McLeod, Adele; Smart, Christine D.; Fry, William E.

2004-01-01

We have investigated the core promoter structure of the oomycete Phytophthora infestans. The transcriptional start sites (TSS) of three previously characterized P. infestans genes, Piexo1, Piexo3, and Piendo1, were determined by primer extension analyses. The TSS regions were homologous to a previously identified 16-nucleotide (nt) core sequence that overlaps the TSS in most oomycete genes. The core promoter regions of Piexo1 and Piendo1 were investigated by using a transient protoplast expression assay and the reporter gene β-glucuronidase. Mutational analyses of the promoters of Piexo1 and Piendo1 showed that there is a putative core promoter element encompassing the TSS (−2 to + 5) that has high sequence and functional homology to a known core promoter element present in other eukaryotes, the initiator element (Inr). Downstream and flanking the Inr is a highly conserved oomycete promoter region (+7 to + 15), hereafter referred to as FPR (flanking promoter region), which is also important for promoter function. The importance of the 19-nt core promoter region (Inr and FPR) in Piexo1 and Piendo1 was further investigated through electrophoretic mobility shift assays (EMSA). The EMSA studies showed that (i) both core promoters were able to specifically bind a protein or protein complex in a P. infestans whole-cell protein extract and (ii) the same mutations that reduced binding of the EMSA complex also reduced β-glucuronidase (GUS) levels in transient expression assays. The consistency of results obtained using two different assays (GUS transient assays [in vivo] and EMSA studies [in vitro]) supports a convergence of inference about the relative importance of specific nucleotides within the 19-nt core promoter region. PMID:14871940

TADPOL: A 1.3 mm Survey of Dust Polarization in Star-forming Cores and Regions

OpenAIRE

Hull, Charles L. H.; Plambeck, Richard L.; Kwon, Woojin; Bower, Geoffrey C.; Carpenter, John M.; Crutcher, Richard M.; Fiege, Jason D.; Franzmann, Erica; Hakobian, Nicholas S.; Heiles, Carl; Houde, Martin; Hughes, A. Meredith; Lamb, James W.; Looney, Leslie W.; Marrone, Daniel P.

2014-01-01

We present λ 1.3 mm Combined Array for Research in Millimeter-wave Astronomy observations of dust polarization toward 30 star-forming cores and eight star-forming regions from the TADPOL survey. We show maps of all sources, and compare the ~2".5 resolution TADPOL maps with ~20" resolution polarization maps from single-dish submillimeter telescopes. Here we do not attempt to interpret the detailed B-field morphology of each object. Rather, we use average B-field orientations to derive conclusi...

Syntrophic biodegradation of hydrocarbon contaminants.

Science.gov (United States)

Gieg, Lisa M; Fowler, S Jane; Berdugo-Clavijo, Carolina

2014-06-01

Anaerobic environments are crucial to global carbon cycling wherein the microbial metabolism of organic matter occurs under a variety of redox conditions. In many anaerobic ecosystems, syntrophy plays a key role wherein microbial species must cooperate, essentially as a single catalytic unit, to metabolize substrates in a mutually beneficial manner. Hydrocarbon-contaminated environments such as groundwater aquifers are typically anaerobic, and often methanogenic. Syntrophic processes are needed to biodegrade hydrocarbons to methane, and recent studies suggest that syntrophic hydrocarbon metabolism can also occur in the presence of electron acceptors. The elucidation of key features of syntrophic processes in defined co-cultures has benefited greatly from advances in 'omics' based tools. Such tools, along with approaches like stable isotope probing, are now being used to monitor carbon flow within an increasing number of hydrocarbon-degrading consortia to pinpoint the key microbial players involved in the degradative pathways. The metagenomic sequencing of hydrocarbon-utilizing consortia should help to further identify key syntrophic features and define microbial interactions in these complex communities. Copyright © 2013 Elsevier Ltd. All rights reserved.

Conceptual core model for the reactor core test

International Nuclear Information System (INIS)

Swenson, L.D.

1970-01-01

Several design options for the ZrH Flight System Reactor were investigated which involved tradeoffs of core excess reactivity, reactor control, coolant mixing and cladding thickness. A design point was selected which is to be the basis for more detailed evaluation in the preliminary design phase. The selected design utilizes 295 elements with 0.670 inch element-to-element pitch, 32 mil thick Incoloy cladding, 18.00 inches long fuel meat, hydrogen content of 6.3 x 10 22 atoms/cc fuel, 10.5 w/o uranium, and a spiraled fin configuration with alternate elements having fins with spiral to the right, spiral to the left, and no fin at all (R-L-N fin configuration). Fin height is 30 mils for the center region of the core and 15 mils for the outer region. (U.S.)

High-resolution gas chromatographic analysis of polycyclic aromatic hydrocarbons and aliphatic hydrocarbons

International Nuclear Information System (INIS)

Perez, M.; Gonzalez, D.

1988-01-01

A study of the analysis by gas chromatography of aromatic polycyclic hydrocarbons and aliphatic hydrocarbons is presented. The separation has been carried out by glass and fused silica capillary column in two different polar stationary phases OV-1 and SE-54. The limitation and the advantages of the procedure are discussed in terms of separation, sensitivity and precision. (Author) 20 refs

Hydrocarbon pollution from marinas in estuarine sediments

Science.gov (United States)

Voudrias, Evangelos A.; Smith, Craig L.

1986-03-01

A measure of the impact of marinas on three Eastern Virginia estuarine creeks was obtained by a study of hydrocarbons in their sediments. Two of the creeks support considerable marine activity, including pleasure boat marinas, boat repair facilities, and commercial fishing operations. The third creek, which served as a control, is seldom used by boats, and is surrounded by marsh and woodland. Sediments from the creeks with marinas contained significantly higher levels of both aromatic and aliphatic hydrocarbons than did the control. Differences in the concentrations of certain oil-pollution indicators, such as the 17α,21β-hopane homologs and phytane, and low molecular weight aromatic hydrocarbons, are indicative of light petroleum fractions. Most of the aromatic hydrocarbons from all creeks, however, appear to have a pyrogenic origin. Although hydrocarbons from three probable origins (petroleum, pyrogenesis, and recent biosynthesis) were detected in all locations, the petroleum-derived and pyrogenic hydrocarbons were of only minor importance relative to the biogenic hydrocarbons in the control creek.

Monitoring hydrocarbons and trace metals in Beaufort Sea sediments and organisms. Final report

International Nuclear Information System (INIS)

Boehm, P.; LeBlanc, L.; Trefry, J.; Marajh-Whittemore, P.; Brown, J.

1990-01-01

As part of the Minerals Management Service's environmental studies of oil and gas exploration and production activities in the Alaskan Beaufort Sea, a study was conducted in 1989 to monitor the marine environment for inputs of chemicals related to drilling and exploration. The 1989 Beaufort Sea Monitoring Program (BSMP) was designed to monitor sediments and selected benthic organisms for trace metals and hydrocarbons so as to infer any changes that might have resulted from drilling and production activities. A series of 49 stations were sampled during the program. The study area extended from Cape Halkett on the western end of Harrison Bay to Griffin Point, east of Barter Island. The sampling design combined an area-wide approach in which stations were treated as replicates of 8 specific geographic regions, with an activity-specific approach, which focused on the potential establishment of metal or hydrocarbon concentration gradients with distance from the Endicott Production Field in Prudhoe Bay. The analytical program focused on the analysis of the fine-fraction of the sediment for a series of trace metals and elements and the analysis of a suite of saturated and aromatic hydrocarbons in the bulk sediment. The total organic carbon (TOB) content and the grain size distribution in the sediments were determined as well. Benthic bivalve molluscs, representative of several feeding types were collected from those stations for which data previously existed from the 1984-1986 BSMP, and were analyzed for metals and saturated and aromatic hydrocarbons. The benthic amphipods were collected, pooled by station or region, and analyzed as well

BIOREMEDIATION OF A PETROLEUM-HYDROCARBON

African Journals Online (AJOL)

ES OBE

under field conditions in the bioremediation of a petroleum- hydrocarbon polluted ... an accelerated biodegradation of petroleum hydrocarbons in a polluted agricultural soil ..... 12) Jackson, M.L. Soil chemical analysis. ... biological assay. 3 rd.

Winning Cores in Parity Games

DEFF Research Database (Denmark)

Vester, Steen

2016-01-01

We introduce the novel notion of winning cores in parity games and develop a deterministic polynomial-time under-approximation algorithm for solving parity games based on winning core approximation. Underlying this algorithm are a number properties about winning cores which are interesting...... in their own right. In particular, we show that the winning core and the winning region for a player in a parity game are equivalently empty. Moreover, the winning core contains all fatal attractors but is not necessarily a dominion itself. Experimental results are very positive both with respect to quality...

Aliphatic hydrocarbon and polycyclic aromatic hydrocarbon geochemistry of twelve major rivers in the Northwest Territories

International Nuclear Information System (INIS)

Backus, S.; Swyripa, M.; Peddle, J.; Jeffries, D.S.

1995-01-01

Suspended sediment and water samples collected from twelve major rivers in the Northwest Territories were analyzed for aliphatic hydrocarbons and polycyclic aromatic hydrocarbons (PAHs) to assess the sources and transport of hydrocarbons entering the Arctic Ocean. Three stations on the Mackenzie River and one station near the mouth of eleven other northern rivers were selected for sampling. Samples were collected on the Mackenzie River on four occasions to characterize spring, summer and fall flow conditions and once on the remaining eleven rivers during high flow conditions. The Mackenzie River is distinctively different then the other eleven rivers. Naturally occurring hydrocarbons predominate in the river. These hydrocarbons include biogenic alkanes, diagenic PAHs, petrogenic alkanes, and PAHs from oil seeps and/or bitumens. Anthropogenic inputs of PAHs are low as indicated by low concentrations of combustion PAHs. Alkyl PAH distributions indicate that a significant component of the lower molecular weight PAH fraction is petrogenic. The majority of the high molecular weight PAHs, together with the petrogenic PAHs have a principal source in the Mackenzie River

The genetic source and timing of hydrocarbon formation in gas hydrate reservoirs in Green Canyon, Block GC955

Science.gov (United States)

Moore, M. T.; Darrah, T.; Cook, A.; Sawyer, D.; Phillips, S.; Whyte, C. J.; Lary, B. A.

2017-12-01

Although large volumes of gas hydrates are known to exist along continental slopes and below permafrost, their role in the energy sector and the global carbon cycle remains uncertain. Investigations regarding the genetic source(s) (i.e., biogenic, thermogenic, mixed sources of hydrocarbon gases), the location of hydrocarbon generation, (whether hydrocarbons formed within the current reservoir formations or underwent migration), rates of clathrate formation, and the timing of natural gas formation/accumulation within clathrates are vital to evaluate economic potential and enhance our understanding of geologic processes. Previous studies addressed some of these questions through analysis of conventional hydrocarbon molecular (C1/C2+) and stable isotopic (e.g., δ13C-CH4, δ2H-CH4, δ13C-CO2) composition of gases, water chemistry and isotopes (e.g., major and trace elements, δ2H-H2O, δ18O-H2O), and dissolved inorganic carbon (δ13C-DIC) of natural gas hydrate systems to determine proportions of biogenic and thermogenic gas. However, the effects from contributions of mixing, transport/migration, methanogenesis, and oxidation in the subsurface can complicate the first-order application of these techniques. Because the original noble gas composition of a fluid is preserved independent of microbial activity, chemical reactions, or changes in oxygen fugacity, the integration of noble gas data can provide both a geochemical fingerprint for sources of fluids and an additional insight as to the uncertainty between effects of mixing versus post-genetic modification. Here, we integrate inert noble gases (He, Ne, Ar, and associated isotopes) with these conventional approaches to better constrain the source of gas hydrate formation and the residence time of fluids (porewaters and natural gases) using radiogenic 4He ingrowth techniques in cores from two boreholes collected as part of the University of Texas led UT-GOM2-01 drilling project. Pressurized cores were extracted from

Optrode for sensing hydrocarbons

Science.gov (United States)

Miller, H.; Milanovich, F.P.; Hirschfeld, T.B.; Miller, F.S.

1988-09-13

A two-phase system employing the Fujiwara reaction is provided for the fluorometric detection of halogenated hydrocarbons. A fiber optic is utilized to illuminate a column of pyridine trapped in a capillary tube coaxially attached at one end to the illuminating end of the fiber optic. A strongly alkaline condition necessary for the reaction is maintained by providing a reservoir of alkali in contact with the column of pyridine, the surface of contact being adjacent to the illuminating end of the fiber optic. A semipermeable membrane caps the other end of the capillary tube, the membrane being preferentially permeable to the halogenated hydrocarbon and but preferentially impermeable to water and pyridine. As the halogenated hydrocarbon diffuses through the membrane and into the column of pyridine, fluorescent reaction products are formed. Light propagated by the fiber optic from a light source, excites the fluorescent products. Light from the fluorescence emission is also collected by the same fiber optic and transmitted to a detector. The intensity of the fluorescence gives a measure of the concentration of the halogenated hydrocarbons. 5 figs.

Biodegradation of petroleum hydrocarbons in hypersaline environments

Directory of Open Access Journals (Sweden)

Luiz Fernando Martins

2012-09-01

Full Text Available Literature on hydrocarbon degradation in extreme hypersaline media presents studies that point to a negative effect of salinity increase on hydrocarbonoclastic activity, while several others report an opposite tendency. Based on information available in the literature, we present a discussion on the reasons that justify these contrary results. Despite the fact that microbial ability to metabolize hydrocarbons is found in extreme hypersaline media, indeed some factors are critical for the occurrence of hydrocarbon degradation in such environments. How these factors affect hydrocarbon degradation and their implications for the assessment of hydrocarbon biodegradation in hypersaline environments are presented in this review.

Succession of Hydrocarbon Degradation and Microbial Diversity during a Simulated Petroleum Seepage in Caspian Sea Sediments

Science.gov (United States)

Mishra, S.; Stagars, M.; Wefers, P.; Schmidt, M.; Knittel, K.; Krueger, M.; Leifer, I.; Treude, T.

2016-02-01

Microbial degradation of petroleum was investigated in intact sediment cores of Caspian Sea during a simulated petroleum seepage using a sediment-oil-flow-through (SOFT) system. Over the course of the SOFT experiment (190 days), distinct redox zones established and evolved in the sediment core. Methanogenesis and sulfate reduction were identified to be important processes in the anaerobic degradation of hydrocarbons. C1 to C6 n-alkanes were completely exhausted in the sulfate-reducing zone and some higher alkanes decreased during the upward migration of petroleum. A diversity of sulfate-reducing bacteria was identified by 16s rRNA phylogenetic studies, some of which are associated with marine seeps and petroleum degradation. The δ13C signal of produced methane decreased from -33.7‰ to -49.5‰ indicating crude oil degradation by methanogenesis, which was supported by enrichment culturing of methanogens with petroleum hydrocarbons and presence of methanogenic archaea. The SOFT system is, to the best of our knowledge, the first system that simulates an oil-seep like condition and enables live monitoring of biogeochemical changes within a sediment core during petroleum seepage. During our presentation we will compare the Caspian Sea data with other sediments we studied using the SOFT system from sites such as Santa Barbara (Pacific Ocean), the North Alex Mud Volcano (Mediterranean Sea) and the Eckernfoerde Bay (Baltic Sea). This research was funded by the Deutsche Forschungsgemeinschaft (SPP 1319) and DEA Deutsche Erdoel AG. Further support came from the Helmholtz and Max Planck Gesellschaft.

A holistic approach to hydrocarbon source allocation in the subtidal sediments of Prince William Sound, Alaska, embayments

International Nuclear Information System (INIS)

Page, D.S.; Bence, A.E.; Burns, W.A.; Boehm, P.D.; Brown, J.S.; Douglas, G.S.

2002-01-01

The complex organic geochemistry record in the subtidal sediments of Prince William Sound, Alaska is a result of much industrial and human activity in the region. Recent oil spills and a regional background of natural petroleum hydrocarbons originating from active hydrocarbon systems in the northern Gulf of Alaska also contribute to the geochemical record. Pyrogenic and petrogenic polycyclic aromatic hydrocarbons (PAH) are introduced regularly to the subtidal sediments at sites of past and present human activities including villages, fish hatcheries, fish camps and recreational campsites as well as abandoned settlements, canneries, sawmills and mines. Hydrocarbon contributions are fingerprinted and quantified using a holistic approach where contributions from multiple sources is determined. The approach involves a good understanding of the history of the area to identify potential sources. It also involves extensive collection of representative samples and an accurate quantitative analysis of the source and sediment samples for PAH analytes and chemical biomarker compounds. Total organic carbon (TOC) does not work in restricted embayments because of a constrained least-square algorithm to determine hydrocarbon sources. It has been shown that sources contributing to the natural petrogenic background are present in Prince William Sound. In particular, pyrogenic hydrocarbons such as combustion products of diesel is significant where there was much human activity. In addition, petroleum produced from the Monterey Formation in California is present in Prince William Sound because in the past, oil and asphalt shipped from California was widely used for fuel. Low level residues of weathered Alaskan North Slope crude oil from the Exxon Valdez spill are also still present. 30 refs., 4 tabs., 2 figs

Evaluation of hydrocarbon potential

International Nuclear Information System (INIS)

Cashman, P.H.; Trexler, J.H. Jr.

1992-01-01

Task 8 is responsible for assessing the hydrocarbon potential of the Yucca Mountain vincinity. Our main focus is source rock stratigraphy in the NTS area in southern Nevada. (In addition, Trexler continues to work on a parallel study of source rock stratigraphy in the oil-producing region of east central Nevada, but this work is not funded by Task 8.) As a supplement to the stratigraphic studies, we are studying the geometry and kinematics of deformation at NTS, particularly as these pertain to reconstructing Paleozoic stratigraphy and to predicting the nature of the Late Paleozoic rocks under Yucca Mountain. Our stratigraphic studies continue to support the interpretation that rocks mapped as the open-quotes Eleana Formationclose quotes are in fact parts of two different Mississippian units. We have made significant progress in determining the basin histories of both units. These place important constraints on regional paleogeographic and tectonic reconstructions. In addition to continued work on the Eleana, we plan to look at the overlying Tippipah Limestone. Preliminary TOC and maturation data indicate that this may be another potential source rock

Noble gas and hydrocarbon tracers in multiphase unconventional hydrocarbon systems: Toward integrated advanced reservoir simulators

Science.gov (United States)

Darrah, T.; Moortgat, J.; Poreda, R. J.; Muehlenbachs, K.; Whyte, C. J.

2015-12-01

Although hydrocarbon production from unconventional energy resources has increased dramatically in the last decade, total unconventional oil and gas recovery from black shales is still less than 25% and 9% of the totals in place, respectively. Further, the majority of increased hydrocarbon production results from increasing the lengths of laterals, the number of hydraulic fracturing stages, and the volume of consumptive water usage. These strategies all reduce the economic efficiency of hydrocarbon extraction. The poor recovery statistics result from an insufficient understanding of some of the key physical processes in complex, organic-rich, low porosity formations (e.g., phase behavior, fluid-rock interactions, and flow mechanisms at nano-scale confinement and the role of natural fractures and faults as conduits for flow). Noble gases and other hydrocarbon tracers are capably of recording subsurface fluid-rock interactions on a variety of geological scales (micro-, meso-, to macro-scale) and provide analogs for the movement of hydrocarbons in the subsurface. As such geochemical data enrich the input for the numerical modeling of multi-phase (e.g., oil, gas, and brine) fluid flow in highly heterogeneous, low permeability formations Herein we will present a combination of noble gas (He, Ne, Ar, Kr, and Xe abundances and isotope ratios) and molecular and isotopic hydrocarbon data from a geographically and geologically diverse set of unconventional hydrocarbon reservoirs in North America. Specifically, we will include data from the Marcellus, Utica, Barnett, Eagle Ford, formations and the Illinois basin. Our presentation will include geochemical and geological interpretation and our perspective on the first steps toward building an advanced reservoir simulator for tracer transport in multicomponent multiphase compositional flow (presented separately, in Moortgat et al., 2015).

Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site.

Science.gov (United States)

Akbari, Ali; Ghoshal, Subhasis

2014-09-15

Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16-C34) in a pilot-scale biopile experiment conducted at 15°C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16-C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day(-1) in biopile tank compared to 0.11 day(-1) in slurry bioreactors for C16-C34 hydrocarbons, the biodegradation extents for this fraction were comparable in these two systems. Copyright © 2014 Elsevier B.V. All rights reserved.

Nuclear reactor core

International Nuclear Information System (INIS)

Koyama, Jun-ichi; Aoyama, Motoo; Ishibashi, Yoko; Mochida, Takaaki; Haikawa, Katsumasa; Yamanaka, Akihiro.

1995-01-01

A reactor core is radially divided into an inner region, an outer region and an outermost region. As a fuel, three kinds of fuels, namely, a high enrichment degree fuel at 3.4%, a middle enrichment degree fuel at 2.3% and a low enrichment degree at 1.1% of a fuel average enrichment degree of fission product are used. Each of the fuels is bisected to upper and lower portions at an axial center thereof. The difference of average enrichment degrees between upper and lower portions is 0.1% for the high enrichment degree fuel, 0.3% for the middle enrichment degree fuel and 0.2% for the low enrichment degree fuel. In addition, the composition of fuels in each of radial regions comprises 100% of the low enrichment degree fuels in the outermost region, 91% of the higher enrichment degree fuels and 9% of the middle enrichment degree fuels in the outer region, and 34% of the high enrichment degree fuels and 30% of the middle enrichment degree fuels in the inner region. With such a constitution, fuel economy can be improved while maintaining the thermal margin in an initially loaded reactor core of a BWR type reactor. (I.N.)

How do salt withdrawal minibasins form? Insights from forward modelling, and implications for hydrocarbon migration

Science.gov (United States)

Peel, Frank J.

2014-09-01

Existing models for the initiation of salt withdrawal minibasins focus on the role of triggers that exist within the minibasin, either stratigraphic (e.g. differential deposition) or tectonic (extension, translation or contraction). Existing studies tend to focus on complex settings, such as continental margins, which contain many different potential triggering mechanisms. It can be difficult in these settings to identify which process is responsible for minibasin initiation, or the influence of individual factors on their subsequent development. Salt withdrawal minibasins also exist in simpler settings, without any obvious intrinsic trigger; the region of the North German Basin used by Trusheim (1960) in the classic definition of salt withdrawal geometries was of this nature. There is no overall basal or surface slope, no major lateral movement, and there is no depositional heterogeneity. Previously recognized trigger processes for minibasin initiation do not apply in this benign setting, suggesting that other, potentially more fundamental, influences may be at work. A simple forward-modelling approach shows how, in the absence of any other mechanism, a new minibasin can develop as the consequence of salt movement driven by its neighbour, and families of withdrawal minibasins can propagate across a region from a single seed point. This new mechanism may explain how some minibasins appear to initiate before the sediment density has exceeded that of the underlying salt. The forward modelling also indicates that some minibasins begin to invert to form turtle anticlines before the underlying salt has been evacuated, so that the timing of turtle formation may not be diagnostic of weld formation. This mechanism may also give rise to salt-cored turtles that have a lens of salt trapped beneath their cores. These new findings have implications for hydrocarbon migration and trapping.

Preliminary core design calculations for the ACPR Upgrade

International Nuclear Information System (INIS)

Pickard, P.S.

1976-01-01

The goal of the Annular Core Pulse Reactor (ACPR) Upgrade design studies is to define a core configuration that provides a significant increase in pulse fluence and fission energy deposition. The reactor modification should provide as flat an energy deposition profile for experiments as feasible. The fuels examined in this study were UO 2 -BeO (5-15 w/o UO 2 ), UC-ZrC-C (200-500 mg U/cc) and U-ZrH 1.5 . The basic core concept examined was a two region core, - a high heat capacity inner core region surrounded by an outer U-ZrH 1.5 region. Survey core calculations utilizing 1D transport calculations and cross sections libraries derived from the ORNL-AMPX code examined relative fuel loadings, fuel temperatures, reactivity requirements and pulse performance improvement. Reference designs for all candidate fuels were defined utilizing 2D transport and Monte Carlo calculations. The performance implications of alternative core designs were also examined for the UO 2 -BeO and UC-ZrC-C fuel candidates. (author)

Low permeability Neogene lithofacies in Northern Croatia as potential unconventional hydrocarbon reservoirs

Science.gov (United States)

Malvić, Tomislav; Sučić, Antonija; Cvetković, Marko; Resanović, Filip; Velić, Josipa

2014-06-01

We present two examples of describing low permeability Neogene clastic lithofacies to outline unconventional hydrocarbon lithofacies. Both examples were selected from the Drava Depression, the largest macrostructure of the Pannonian Basin System located in Croatia. The first example is the Beničanci Field, the largest Croatian hydrocarbon reservoir discovered in Badenian coarse-grained clastics that consists mostly of breccia. The definition of low permeability lithofacies is related to the margins of the existing reservoir, where the reservoir lithology changed into a transitional one, which is mainly depicted by the marlitic sandstones. However, calculation of the POS (probability of success of new hydrocarbons) shows critical geological categories where probabilities are lower than those in the viable reservoir with proven reserves. Potential new hydrocarbon volumes are located in the structural margins, along the oil-water contact, with a POS of 9.375%. These potential reserves in those areas can be classified as probable. A second example was the Cremušina Structure, where a hydrocarbon reservoir was not proven, but where the entire structure has been transferred onto regional migration pathways. The Lower Pontian lithology is described from well logs as fine-grained sandstones with large sections of silty or marly clastics. As a result, the average porosity is low for conventional reservoir classification (10.57%). However, it is still an interesting case for consideration as a potentially unconventional reservoir, such as the "tight" sandstones.

Differentiation of naturally-occurring vs. artificial hydrocarbons in a landfill groundwater investigation

International Nuclear Information System (INIS)

Beaver, J.L.; Hartness, J.A.; Breeding, L.B.; Buchanan, D.M.

1994-01-01

Interpretation of groundwater sampling data at a large municipal/industrial landfill indicates contamination by both artificial and naturally-occurring hydrocarbons. Site hydrogeology consists of three different water bearing zones. The uppermost (shallow) aquifer is an unconfined unit consisting of silt, clay, and sand deposits. An intermediate depth semiconfined aquifer underlies the unconfined unit, and consists of a chert rubble zone and the upper portion of a fractured and solution-enhanced limestone formation. A regionally-extensive organic-rich shale underlies the semiconfined aquifer and separates it from the deep confined aquifer, which also consists of limestone. Groundwater investigations at the landfill have detected chlorinated and non-chlorinated hydrocarbons in the different aquifer intervals. Chlorinated hydrocarbons detected include tetrachloroethene, dichloroethene, and vinyl chloride and occur almost exclusively in the shallow aquifer. Aromatic hydrocarbons detected include benzene, toluene, ethylbenzene, and xylene (BTEX) and-occur in the intermediate and deep aquifers. The landfill was originally interpreted as the source of the contaminants. The observation of free-phase liquid hydrocarbons in the intermediate aquifer at the site, and high dissolved BTEX levels in the deep and intermediate aquifers upgradient of the landfill suggest that the aromatics were derived from a source other than the landfill. A potential source of BTEX contamination may be abandoned (pre-1930) natural gas wells located near the landfill. An additional BTEX source may be the organic-rich shale formation (a documented petroleum source rock)

Dust measurement campaign in the Mantes region atmosphere; Campagne de mesures ``poussieres`` dans l`atmosphere de la region Mantaise

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-31

A measurement campaign have been carried out in the Mantes region (West of Paris) in order to determine particulate concentrations and types in the city atmosphere: granulometric particulate concentrations and concentration levels of the various types of airborne particulates (metals and metalloids, black smoke, polycyclic aromatic hydrocarbons, mono-cyclic aromatic hydrocarbons) are presented. The wind direction and speed have been taken into consideration

Latin American electric power developments and hydrocarbon demands

International Nuclear Information System (INIS)

Sierra, G.S.

1994-01-01

Energy sectors in Latin American countries are undergoing a series of far-reaching changes in institutional arrangements and roles. These changes will have a decisive influence on energy sector evolution in coming decades. The results of two decades of mismanagement in the region's energy sector are outlined, showing stagnation in the electric power and petroleum industries caused by such factors as bureaucratic management, preferential treatment given to public enterprises, the adoption of objectives other than economic profitability, insufficient self-generation of resources due to tariffs not reflecting economic costs, and heavy debt burdens. If forecasts of future energy demand in Latin America are correct, the region's hydrocarbon sector will have to invest ca US$20 billion/y and the electric power sector nearly the same amount. This is considered beyond the capacity of the region's industries. Private sector participation is expected to raise the efficiency level of the hydrocarbon and power industries through such initiatives as privatization (complete or partial), joint government-private ventures, subcontracting, direct investment, and opening of monopolies such as power distribution to third-party competition. The state role in this process will be to create a suitable environment for private enterprise including clear and stable rules and regulatory frameworks. Financing options are discussed along with ways to reduce investment requirements. It is especially possible to reduce such requirements in the power sector through such means as retrofitting of plants with more modern equipment, reducing power losses, improved metering and billing, energy substitution, demand-side management, and energy conservation programs

Naturally occurring resistance mutations within the core and NS5B regions in hepatitis C genotypes, particularly genotype 5a, in South Africa.

Science.gov (United States)

Prabdial-Sing, N; Blackard, J T; Puren, A J; Mahomed, A; Abuelhassan, W; Mahlangu, J; Vermeulen, M; Bowyer, S M

2016-03-01

Approximately 1 million South Africans are infected with Hepatitis C virus (HCV). The standard of care (SOC) in South Africa is combination therapy (pegylated interferon and ribavirin). HCV genotypes and/or mutations in the core/non-structural regions have been associated with response to therapy and/or disease progression. This study examines mutations in the core (29-280 amino acids, including ∼ 90 E1 amino acids) and NS5B (241-306 amino acids) regions on pre-treatment isolates from patients attending Johannesburg hospitals or asymptomatic South African blood donors. Diversity within known CD4+ and CD8+ T-cell epitopes was also explored. Samples grouped into subtypes 1a(N = 10) 1b(N = 12), 3a(N = 5), 4a(N = 3) and 5a(N = 61). Two mutations, associated with interferon resistance-R70Q and T110N-were present in 29 genotype 5a core sequences. No resistance mutation to NS5B nucleotide inhibitors, sofosbuvir was found. Six putative CD8+ and one CD4+ T-cell epitope sequence in the core region showed binding scores of <300 IC50nM to HLA alleles frequently observed in the South African population. No known CD8+ and CD4+ T-cell epitopes were mapped in the NS5B region. The analysis begs the question whether those infected with genotype 5a will benefit better on interferon-free combination therapies. This study provides new insight into one of the lesser studied HCV genotypes and compares the diversity seen in a large pre-treatment cohort with other subtypes. Copyright © 2015 Elsevier B.V. All rights reserved.

Process for separating liquid hydrocarbons from waxes

Energy Technology Data Exchange (ETDEWEB)

Sowa, F J

1948-03-08

A process is described for the separation of liquid hydrocarbons from waxes comprising adding to a mixture of liquid hydrocarbons and waxes a sufficient quantity of an organo-silicon compound to cause the separation of the hydrocarbon and wax. The organo-silicon compounds are selected from the class of organic silicanes and their hydrolysis products and polymers. The silicanes have the formula R/sub y/SiX/sub z/, in which R is a saturated or unsaturated hydrocarbon radical, X is a halogen or another hydrocarbon radical or an -OR group, y has a value 1, 2, or 3 and z has a value 1, 2, or 3.

Process for treating hydrocarbons, etc

Energy Technology Data Exchange (ETDEWEB)

1933-09-15

A process is described for treating simultaneously bituminous substances and hydrocarbon oils for the production of low-boiling hydrocarbons and volatilization of the bituminous substances, characterized by the fact that it consists of heating a current of charge constituted by a mixture of the bituminous substances and hydrocarbon oils, to a high temperature, passing the heated current into a zone of extended reaction where the vapors are separated from the liquid or solid residue to favor transformation of the liquid hydrocarbons and volatilization of the bituminous substances, owing to the utilization of a heating agent carried to a high temperature being brought in contact with the heated charge in order to communicate its heat to the charge, while this later presents itself as relatively fine pellet or in the condition of distinct particles, particularly separated from one another.

Benthic Bioprocessing of Hydrocarbons in the Natural Deep-Sea Environment

Science.gov (United States)

Sultan, N.; MacDonald, I. R.; Bohrmann, G.; Schubotz, F.; Johansen, C.

2017-12-01

Science is accustomed to quantifying ecosystem processes that consume carbon from primary production as it drifts downward through the photic zone. Comparably efficient processes operate in reverse, as living and non-living components sequester and re-mineralize a large fraction of hydrocarbons that migrate out of traps and reservoirs to the seafloor interface. Together, they comprise a sink that prevents these hydrocarbons from escaping upward into the water column. Although quantification of the local or regional magnitude of this sink poses steep challenges, we can make progress by classifying and mapping the biological communities and geological intrusions that are generated from hydrocarbons in the deep sea. Gulf of Mexico examples discussed in this presentation extend across a broad range of depths (550, 1200, and 3200 m) and include major differences in hydrocarbon composition (from gas to liquid oil to asphaltene-dominated solids). Formation of gas hydrate is a dynamic process in each depth zone. At upper depths, gas hydrate is unstable at a timescale of months to years and serves as a substrate for microbial consortia and mussel symbiosis. At extreme depths, gas hydrate supports large and dense tubeworm colonies that conserve the material from decomposition. Timescales for biogeochemical weathering of oil and asphalts are decadal or longer, as shown by sequential alterations and changing biological colonization. Understanding these processes is crucial as we prepare for wider and deeper energy exploitation in the Gulf of Mexico and beyond.

Biogeographic Comparison of Lophelia-Associated Bacterial Communities in the Western Atlantic Reveals Conserved Core Microbiome

Directory of Open Access Journals (Sweden)

Christina A. Kellogg

2017-05-01

Full Text Available Over the last decade, publications on deep-sea corals have tripled. Most attention has been paid to Lophelia pertusa, a globally distributed scleractinian coral that creates critical three-dimensional habitat in the deep ocean. The bacterial community associated with L. pertusa has been previously described by a number of studies at sites in the Mediterranean Sea, Norwegian fjords, off Great Britain, and in the Gulf of Mexico (GOM. However, use of different methodologies prevents direct comparisons in most cases. Our objectives were to address intra-regional variation and to identify any conserved bacterial core community. We collected samples from three distinct colonies of L. pertusa at each of four locations within the western Atlantic: three sites within the GOM and one off the east coast of the United States. Amplicon libraries of 16S rRNA genes were generated using primers targeting the V4–V5 hypervariable region and 454 pyrosequencing. The dominant phylum was Proteobacteria (75–96%. At the family level, 80–95% of each sample was comprised of five groups: Pirellulaceae, Pseudonocardiaceae, Rhodobacteraceae, Sphingomonadaceae, and unclassified Oceanospirillales. Principal coordinate analysis based on weighted UniFrac distances showed a clear distinction between the GOM and Atlantic samples. Interestingly, the replicate samples from each location did not always cluster together, indicating there is not a strong site-specific influence. The core bacterial community, conserved in 100% of the samples, was dominated by the operational taxonomic units of genera Novosphingobium and Pseudonocardia, both known degraders of aromatic hydrocarbons. The sequence of another core member, Propionibacterium, was also found in prior studies of L. pertusa from Norway and Great Britain, suggesting a role as a conserved symbiont. By examining more than 40,000 sequences per sample, we found that GOM samples were dominated by the identified conserved core

Exploratory Hydrocarbon Drilling Impacts to Arctic Lake Ecosystems

Science.gov (United States)

Thienpont, Joshua R.; Kokelj, Steven V.; Korosi, Jennifer B.; Cheng, Elisa S.; Desjardins, Cyndy; Kimpe, Linda E.; Blais, Jules M.; Pisaric, Michael FJ.; Smol, John P.

2013-01-01

Recent attention regarding the impacts of oil and gas development and exploitation has focused on the unintentional release of hydrocarbons into the environment, whilst the potential negative effects of other possible avenues of environmental contamination are less well documented. In the hydrocarbon-rich and ecologically sensitive Mackenzie Delta region (NT, Canada), saline wastes associated with hydrocarbon exploration have typically been disposed of in drilling sumps (i.e., large pits excavated into the permafrost) that were believed to be a permanent containment solution. However, failure of permafrost as a waste containment medium may cause impacts to lakes in this sensitive environment. Here, we examine the effects of degrading drilling sumps on water quality by combining paleolimnological approaches with the analysis of an extensive present-day water chemistry dataset. This dataset includes lakes believed to have been impacted by saline drilling fluids leaching from drilling sumps, lakes with no visible disturbances, and lakes impacted by significant, naturally occurring permafrost thaw in the form of retrogressive thaw slumps. We show that lakes impacted by compromised drilling sumps have significantly elevated lakewater conductivity levels compared to control sites. Chloride levels are particularly elevated in sump-impacted lakes relative to all other lakes included in the survey. Paleolimnological analyses showed that invertebrate assemblages appear to have responded to the leaching of drilling wastes by a discernible increase in a taxon known to be tolerant of elevated conductivity coincident with the timing of sump construction. This suggests construction and abandonment techniques at, or soon after, sump establishment may result in impacts to downstream aquatic ecosystems. With hydrocarbon development in the north predicted to expand in the coming decades, the use of sumps must be examined in light of the threat of accelerated permafrost thaw, and the

New Technique for TOC Estimation Based on Thermal Core Logging in Low-Permeable Formations (Bazhen fm.)

Science.gov (United States)

Popov, Evgeny; Popov, Yury; Spasennykh, Mikhail; Kozlova, Elena; Chekhonin, Evgeny; Zagranovskaya, Dzhuliya; Belenkaya, Irina; Alekseev, Aleksey

2016-04-01

A practical method of organic-rich intervals identifying within the low-permeable dispersive rocks based on thermal conductivity measurements along the core is presented. Non-destructive non-contact thermal core logging was performed with optical scanning technique on 4 685 full size core samples from 7 wells drilled in four low-permeable zones of the Bazhen formation (B.fm.) in the Western Siberia (Russia). The method employs continuous simultaneous measurements of rock anisotropy, volumetric heat capacity, thermal anisotropy coefficient and thermal heterogeneity factor along the cores allowing the high vertical resolution (of up to 1-2 mm). B.fm. rock matrix thermal conductivity was observed to be essentially stable within the range of 2.5-2.7 W/(m*K). However, stable matrix thermal conductivity along with the high thermal anisotropy coefficient is characteristic for B.fm. sediments due to the low rock porosity values. It is shown experimentally that thermal parameters measured relate linearly to organic richness rather than to porosity coefficient deviations. Thus, a new technique employing the transformation of the thermal conductivity profiles into continuous profiles of total organic carbon (TOC) values along the core was developed. Comparison of TOC values, estimated from the thermal conductivity values, with experimental pyrolytic TOC estimations of 665 samples from the cores using the Rock-Eval and HAWK instruments demonstrated high efficiency of the new technique for the organic rich intervals separation. The data obtained with the new technique are essential for the SR hydrocarbon generation potential, for basin and petroleum system modeling application, and estimation of hydrocarbon reserves. The method allows for the TOC richness to be accurately assessed using the thermal well logs. The research work was done with financial support of the Russian Ministry of Education and Science (unique identification number RFMEFI58114X0008).

Evaluation of effects on integral parameters, due to homogenization of one region of a core-blanket system

International Nuclear Information System (INIS)

Assis, J.T. de

1982-01-01

The effects produced on the integral parameters due to the homogenization in the core-blanket inrterface, were evaluated, adopting an 1D diffusion calculation. The calculation for one plane cell with the characteristics of the critical mounting ZPR-6-5, was done using the Hetaire computer code with the Carnaval II data library for 25 energy groups. For the transport calculation the ANISN and RMAT1D computer codes were used. By the homogenization of an interface region, flux values, cross sections and reactivity are obtained for several thicknesses of this region. The results of diffusion calculation are compared with the transport calculation. (E.G.) [pt

EXTINCTION AND POLYCYCLIC AROMATIC HYDROCARBON INTENSITY VARIATIONS ACROSS THE H II REGION IRAS 12063–6259

International Nuclear Information System (INIS)

Stock, D. J.; Peeters, E.; Otaguro, J. N.; Tielens, A. G. G. M.; Bik, A.

2013-01-01

The spatial variations in polycyclic aromatic hydrocarbon (PAH) band intensities are normally attributed to the physical conditions of the emitting PAHs, however in recent years it has been suggested that such variations are caused mainly by extinction. To resolve this question, we have obtained near-infrared (NIR), mid-infrared (MIR), and radio observations of the compact H II region IRAS 12063–6259. We use these data to construct multiple independent extinction maps and also to measure the main PAH features (6.2, 7.7, 8.6, and 11.2 μm) in the MIR. Three extinction maps are derived: the first using the NIR hydrogen lines and case B recombination theory; the second combining the NIR data with radio data; and the third making use of the Spitzer/IRS MIR observations to measure the 9.8 μm silicate absorption feature using the Spoon method and PAHFIT (as the depth of this feature can be related to overall extinction). The silicate absorption over the bright, southern component of IRAS 12063–6259 is almost absent while the other methods find significant extinction. While such breakdowns of the relationship between the NIR extinction and the 9.8 μm absorption have been observed in molecular clouds, they have never been observed for H II regions. We then compare the PAH intensity variations in the Spitzer/IRS data after dereddening to those found in the original data. It was found that in most cases, the PAH band intensity variations persist even after dereddening, implying that extinction is not the main cause of the PAH band intensity variations.

Gamma-radiation induced polymerization of methyl methacrylate in aliphatic hydrocarbons: kinetics and evidence for incorporation of hydrocarbon in the polymer chain

International Nuclear Information System (INIS)

Mohan, H.; Iyer, R.M.

1989-01-01

On γ-radiolysis, the rate of polymerization of methyl methacrylate in hydrocarbon solvents is observed to decrease. It is explained by hydrocarbon entry into the polymer chains. The hydrocarbon entry into the polymer chains is observed to take place at later stages of polymerization and increases with hydrocarbon chain length. The extent of hydrocarbon entry into the polymer chains is estimated by NMR and GLC analysis. It is observed to be equal to ∼ 12% corresponding to ∼ 97 hexadecane molecules in each polymer chain. The IR, DSC, MW determination and radiation effects on the polymer showed evidences for hydrocarbon entry into the polymer. It is explained by chain transfer from the growing polymer radical to the hydrocarbon molecules. The chain transfer constant is determined to be equal to 1 x 10 -2 . (author)

Monitoring of Hydrocarbons in Sediment and Biota Related to Oil and Gas Development in Near- and Off-Shore Areas of the Arctic Beaufort Sea, Alaska

Science.gov (United States)

Durell, G.; Hardin, J.; Libby, S.

2016-02-01

There is increasing interest in extracting oil and gas from offshore environments of Alaska. The Arctic Nearshore Impact Monitoring in Development Area (ANIMIDA) project, started in 1999, has been producing information to evaluate potential effects of oil and gas activities in the Alaskan Beaufort Sea. ANIMIDA was preceded by the Beaufort Sea Monitoring Program. Monitoring has mostly been in pre-drilling locations, but also during development and production periods. Surveys were conducted to assess bottom sediment, sediment cores, suspended sediment, and biota for polycyclic aromatic hydrocarbons (PAH), saturated hydrocarbons, biological and petroleum markers, and geophysical parameters. The concentrations measured in sediments and biota were at or near background throughout most of the Beaufort Sea. There were no significant differences between exploration, production, and background locations, and the concentrations were consistently below those of ecological concern. For instance, TPAH in sediment ranged from below 100 to about 1,000 µg/kg and were controlled primarily by sediment characteristics (e.g., grain size and organic carbon). Hydrocarbons in sediments were from petrogenic, pyrogenic, and biogenic sources. Small areas with indications of input of anthropogenic chemicals were identified by sensitive diagnostic analysis techniques and are possibly associated with historic exploratory drilling and vessels. Sediment cores indicate a uniform historical deposition of hydrocarbons, although some evidence of past drilling activities were observed. Fish, amphipods, and clams contained background levels of hydrocarbons and showed no evidence of effects from accumulation of contaminants; TPAH concentrations were below 100 µg/kg in most biota. Noteworthy interannual fluctuations were observed for PAH concentrations in sediment and biota, likely due to winnowing of sediment fines by large storms and annual variations in river discharges. Significant natural sources

Steam hydrocarbon cracking and reforming

NARCIS (Netherlands)

Golombok, M.

2004-01-01

Many industrial chemical processes are taught as distinct contrasting reactions when in fact the unifying comparisons are greater than the contrasts. We examine steam hydrocarbon reforming and steam hydrocarbon cracking as an example of two processes that operate under different chemical reactivity

Russia and China hydrocarbon relations. A building block toward international hydrocarbon regulation?

International Nuclear Information System (INIS)

Locatelli, Catherine; Abbas, Mehdi; Rossiaud, Sylvain

2015-12-01

This article is a first step of a research agenda on international hydrocarbon regulations. With regards to both: i) the new wealth and power equilibrium in the international political economy and ii) the new political economy of carbon that is emerging from The Paris agreement on Climate changes, this research agenda aims at analysing the changing national structures of governance and the ways these changes lead to international, bilateral, pluri-lateral or multilateral hydrocarbon regulation

Core-shell indium (III) sulfide@metal-organic framework nanocomposite as an adsorbent for the dispersive solid-phase extraction of nitro-polycyclic aromatic hydrocarbons.

Science.gov (United States)

Jia, Yuqian; Zhao, Yanfang; Zhao, Mei; Wang, Zhenhua; Chen, Xiangfeng; Wang, Minglin

2018-05-25

A core-shell discoid shaped indium (III) sulfide@metal-organic framework (MIL-125(Ti)) nanocomposite was synthesized by a solvothermal method and explored as an adsorbent material for dispersive solid-phase extraction (d-SPE). The as-synthesized sorbent was characterized by scanning electron microscopy, energy-dispersive spectroscopy, transmission electron microscopy, powder X-ray diffraction, N 2 adsorption-desorption analysis, and Fourier transform infrared spectroscopy. The extraction performance was evaluated by the d-SPE of 16 nitro-polycyclic aromatic hydrocarbons (NPAHs) from water samples. The analysis was carried out by gas chromatography (GC) coupled with triple quadruple mass spectrometer in negative chemical ionization (NCI) mode. The selected ion monitoring (SIM) was used in the quantification of the target NPAHs. Extraction factors affecting the d-SPE, including the ionic strength, extraction temperature, and extraction time were optimized by the response surface methodology. The developed d-SPE method showed good linear correlations from 10 to 1000 ng L -1 (r > 0.99), low detection limits (2.9-83.0 ng L -1 ), satisfactory repeatability (relative standard deviation of <10%, n = 6), and acceptable recoveries (71.3%-112.2%) for water samples. The developed method was used for the food and environmental sample analysis. The results demonstrated that the method could be used for sample preparation of trace NPAHs in real samples. Copyright © 2018. Published by Elsevier B.V.

Trial coring in LLRW trenches at Chalk River

International Nuclear Information System (INIS)

Donders, R.E.; Killey, R.W.D.; Franklin, K.J.; Strobel, G.S.

1996-11-01

As part of a program to better characterize the low-hazard radioactive waste managed by AECL at Chalk River Laboratories, coring techniques in waste trenches are being assessed. Trial coring has demonstrated that sampling in waste regions is possible, and that boreholes can be placed through the waste trenches. Such coring provides a valuable information-gathering technique. Information available from trench coring includes: trench cover depth, waste region depth, waste compaction level, and detailed stratigraphic data; soil moisture content and facility drainage performance; borehole gamma logs that indicate radiation levels in the region of the borehole; biochemical conditions in the waste regions, vadose zone, and groundwater; site specific information relevant to contaminant migration modelling or remedial actions; information on contaminant releases and inventories. Boreholes through the trenches can also provide a means for early detection of potential contaminant releases. (author). 4 refs., 4 tabs., 4 figs

27 CFR 21.125 - Rubber hydrocarbon solvent.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Rubber hydrocarbon solvent. 21.125 Section 21.125 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU....125 Rubber hydrocarbon solvent. (a) Rubber hydrocarbon solvent is a petroleum derivative. (b...

Distribution of polycyclic aromatic hydrocarbons in thirty typical soil profiles in the Yangtze River Delta region, east China

International Nuclear Information System (INIS)

Ping, L.F.; Luo, Y.M.; Zhang, H.B.; Li, Q.B.; Wu, L.H.

2007-01-01

Polycyclic aromatic hydrocarbons (PAHs) were quantified in 30 soil profiles from the Yangtze River Delta Region, in east China. Relative concentrations of PAH compounds with different benzene rings and ratios of fluoranthene to fluoranthene plus pyrene and benz(a)anthracene to benz(a)anthracene plus chrysene were used to identify the possible sources of soil PAHs. Total concentrations of 15 PAHs in topsoils ranged from 8.6 to 3881 μg kg -1 with an average of 397 μg kg -1 . Half of the soil samples were considered to be contaminated with PAHs (>200 μg kg -1 ) and two sampling sites were heavily polluted by PAHs with concentrations >1000 μg kg -1 . Phenanthrene was found in soils below a depth of 100 cm in half of the sampling sites, but the detectable ratio of benzo(a)pyrene decreased sharply from 100% in topsoil to 0 in the 4th horizon. - The information was provided on levels, distributions, and possible sources of PAHs in the soils of Yangtze River Delta area

Collision data involving hydro-carbon molecules

International Nuclear Information System (INIS)

Tawara, H.; Itikawa, Y.; Nishimura, H.; Tanaka, H.; Nakamura, Y.

1990-07-01

Hydro-carbon molecules are abundantly produced when graphites are used as internal wall materials of hydrogen plasmas and strongly influence properties of low temperature plasmas near the edges as well as those of high temperature plasmas at the center. In this report, following simple description of the production mechanisms of hydro-carbon molecules under the interactions between graphite and hydrogen plasma, the present status of collision data for hydro-carbon molecules by electron impact is discussed and the relevant data are summarized in a series of figures and tables. It should also be noted that, in addition to fusion plasmas, these hydrocarbon data compiled here are quite useful in other applications such as plasma chemistry and material processing. (author)

On the Dynamics of Edge-core Coupling

Energy Technology Data Exchange (ETDEWEB)

Hahm,T.S.; Diamond, P.H.; Lin, Z.; Rewoldt, G.; Gurcan, O.; Ethier, S.

2005-08-26

One of the nagging, unresolved questions in fusion theory is concerned with the extent of the edge. Gyrokinetic particle simulations of toroidal ion temperature gradient (ITG) turbulence spreading using the Gyrokinetic Toroidal Code (GTC) [Z. Lin et al., Science 281, 1835 (1998)] and its related dynamical model have been extended to a system with radially varying ion temperature gradient, in order to study the inward spreading of edge turbulence toward the core plasma. Due to such spreading, the turbulence intensity in the core region is significantly enhanced over the value obtained from simulations of the core region only, and the precise boundary of the edge region is blurred. Even when the core gradient is within the Dimits shift regime (i.e., dominated by self-generated zonal flows which reduce the transport to a negligible value), a significant level of turbulence can penetrate to the core due to spreading from the edge. The scaling of the turbulent front propagation speed is closer to the prediction from a nonlinear diffusion model than from one based on linear toroidal coupling.

Process for desulfurizing hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

1937-04-12

A process is described for the desulfurization of a mixture of hydrocarbons, and in particular hydrocarbons containing less than 7 atoms of carbon and sulfur compounds of the type of sulfur carbonyl, characterized by the fact that the mixture, preferably in the liquid phase, is brought in contact with a solution of caustic alkali, essentially anhydrous or preferably with a solution of alkali hydroxide in an organic hydroxy nonacid solvent, for example, an alcohol, or with an alkaline alcoholate, under conditions suitable to the formation of hydrogen sulfide which produces a hydrocarbon mixture free from sulfur compounds of the sulfur carbonyl type but containing hydrogen sulfide, and that it is treated, following mixing, having beem submitted to the first treatment, by means of aqueous alkaline hydroxide to eliminate the hydrogen sulfide.

Tolerance to Polycyclic Aromatic Hydrocarbons (PAHs by filamentous fungi isolated from contaminated sediment in the Amazon region

Directory of Open Access Journals (Sweden)

Hilton Marcelo de Lima Souza

2017-11-01

Full Text Available Tolerance to Polycyclic Hydrocarbons Aromatic (PAHs is considered an important characteristic when assessing the bioremediation potential of microorganisms. Given this, the objective of this research was to assay filamentous fungi from the Amazon region, isolated from sediments with differents levels of contamination by PAHs, for tolerance to phenanthrene and pyrene. To achieve this, fungal cultures plugs (5 mm, obtained after 7 days growth, were transferred to petri dishes containing 20% Sabouraud dextrose agar medium, after surface innoculation with phenanthrene and pyrene crystals, separately. Radial mycelial growth was evaluated after 10 days at five different concentration levels for each contaminant and control group, all in triplicate for each treatment. Fungal growth and growth inhibition rates were calculated. The average growth of the colonies in each treatment was compared with one-way ANOVA, followed by a Tukey Test (p < 0,05. All fungi showed tolerant to phenanthrene and pyrene. However, Hypoxylon sp. showed the lowest growth inhibition rate and average growth rates significantly different of the other six tested species. Hypoxylon sp. has been shown to be a promising genetic resource for use in new studies of PAHs degradation.

Broadband polymer microstructured THz fiber coupler with downdoped cores

DEFF Research Database (Denmark)

Nielsen, Kristian; Rasmussen, Henrik K.; Bang, Ole

2010-01-01

We demonstrate a broadband THz directional coupler based on a dual core photonic crystal fiber (PCF) design with mechanically down-doped core regions. For a center frequency of 1.3 THz we demonstrate a bandwidth of 0.65 THz.......We demonstrate a broadband THz directional coupler based on a dual core photonic crystal fiber (PCF) design with mechanically down-doped core regions. For a center frequency of 1.3 THz we demonstrate a bandwidth of 0.65 THz....

Hydrocarbon-degrading bacteria isolation and surfactant influence ...

African Journals Online (AJOL)

Hydrocarbons are substantially insoluble in water, often remaining partitioned in the non-aqueous phase liquid (NAPL). However, there had been little or no attempts to advance the bioavailability of hydrocarbons through the use of surfactants. This study was conducted based on the need to isolate hydrocarbon degrading ...

Investigation of the suspected presence of solid hydrocarbon in bedded salt samples from the Palo Duro Basin, Texas

International Nuclear Information System (INIS)

1985-10-01

This report contains laboratory test results for two bedded salt samples from the Grabbe No. 1 (PD-2) Well of the Palo Duro Basin, Texas. This study was commissioned to determine whether or not solid hydrocarbons exist in bedded salt samples in the Palo Duro Basin. Laboratory investigations include electron microprobe examinations on polished thin sections and optical examinations and chemical tests on insoluble residues of the salt samples. No direct evidence was found that identifiable solid hydrocarbons are present in either sample of the bedded salt core. The total carbon content of the two salt samples was measured yielding 0.016 and 0.022 weight percent carbon. Detailed microscopic analyses showed that the carbon in the samples was associated with calcite, clays, and the epoxy resin used in sample preparation

High Pressure Preignition Chemistry of Hydrocarbons and Hydrocarbon Mixtures

National Research Council Canada - National Science Library

Cernansky, N.P

1998-01-01

.... The research program entailed mechanistic studies examining the oxidation chemistry of single-component hydrocarbons and ignition studies examining the overall ignition of pure single component fuels and fuel blends...

Reactor core performance calculating device

International Nuclear Information System (INIS)

Tominaga, Kenji; Bando, Masaru; Sano, Hiroki; Maruyama, Hiromi.

1995-01-01

The device of the present invention can calculate a power distribution efficiently at high speed by a plurality of calculation means while taking an amount of the reactor state into consideration. Namely, an input device takes data from a measuring device for the amount of the reactor core state such as a large number of neutron detectors disposed in the reactor core for monitoring the reactor state during operation. An input data distribution device comprises a state recognition section and a data distribution section. The state recognition section recognizes the kind and amount of the inputted data and information of the calculation means. The data distribution section analyzes the characteristic of the inputted data, divides them into a several groups, allocates them to each of the calculation means for the purpose of calculating the reactor core performance efficiently at high speed based on the information from the state recognition section. A plurality of the calculation means calculate power distribution of each of regions based on the allocated inputted data, to determine the power distribution of the entire reactor core. As a result, the reactor core can be evaluated at high accuracy and at high speed irrespective of the whole reactor core or partial region. (I.S.)

Process for refining hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Risenfeld, E H

1924-11-26

A process is disclosed for the refining of hydrocarbons or other mixtures through treatment in vapor form with metal catalysts, characterized by such metals being used as catalysts, which are obtained by reduction of the oxide of minerals containing the iron group, and by the vapors of the hydrocarbons, in the presence of the water vapor, being led over these catalysts at temperatures from 200 to 300/sup 0/C.

Influence of anthropogenic activities on PAHs in sediments in a significant gulf of low-latitude developing regions, the Beibu Gulf, South China Sea: distribution, sources, inventory and probability risk.

Science.gov (United States)

Li, Pingyang; Xue, Rui; Wang, Yinghui; Zhang, Ruijie; Zhang, Gan

2015-01-15

Fifteen polycyclic aromatic hydrocarbons (PAHs) in 41 surface sediment samples and a sediment core (50 cm) from the Beibu Gulf, a significant low-latitude developing gulf, were analyzed. PAHs concentrations were 3.01-388 ng g(-)(1) (mean 95.5 ng g(-)(1)) in the surface sediments and 10.5-87.1 ng g(-)(1) (average 41.1 ng g(-)(1)) in the sediment core. Source apportionment indicated that PAHs were generated from coke production and vehicular emissions (39.4%), coal and biomass combustion (35.8%), and petrogenic sources (24.8%). PAHs were mainly concentrated in the industrialized and urbanized regions and the harbor, and were transported by atmospheric deposition to the marine matrix. The mass inventory (1.57-2.62t) and probability risk showed sediments here served as an important reservoir but low PAH risk. Different from oil and natural gas in developed regions, coal combustion has always been a significant energy consumption pattern in this developing region for the past 30 years (56 ± 5%). Copyright © 2014 Elsevier Ltd. All rights reserved.

Aryl hydrocarbon receptor (AhR) inducers and estrogen receptor (ER) activities in surface sediments of Three Gorges Reservoir, China evaluated with in vitro cell bioassays

NARCIS (Netherlands)

Wang, J.; Bovee, T.F.H.; Bi, Y.; Bernhöft, S.; Schramm, K.W.

2014-01-01

Two types of biological tests were employed for monitoring the toxicological profile of sediment cores in the Three Gorges Reservoir (TGR), China. In the present study, sediments collected in June 2010 from TGR were analyzed for estrogen receptor (ER)- and aryl hydrocarbon receptor (AhR)-mediated

Improvement of SSR core design for ABWR-II

International Nuclear Information System (INIS)

Moriwaki, Masanao; Aoyama, Motoo; Okada, Hiroyuki; Kitamura, Hideya; Sakurada, Koichi; Tanabe, Akira

2003-01-01

In order to enhance the spectral shift effect in the ABWR-II reactor, a novel core design to bring out better performance of spectral shift rods (SSRs) is studied. The SSR is a new type of water rod, in which the water level develops naturally during operation and changes according to the coolant flow rate through the channel. By using the SSR, the average moderator density, which is directly related to core reactivity, can be controlled over a wide range by the core flow rate. In the new SSR core design, two types of SSR bundles, in which settings for the SSR water levels are different, are utilized and loaded according to flow distribution in the core. This two-region SSR core design allows wide variation in the average SSR water level, thus improving fuel economy. Enhancement of SSR function in the two-region SSR core increases the uranium saving factor by about 25%, from the 6% of the conventional uniform SSR core to about 8%. (author)

Zero-bias tunneling anomaly at a vortex core

International Nuclear Information System (INIS)

Overhauser, A.W.; Daemen, L.L.

1989-01-01

The sharp peak in the tunneling conductance at a vortex core, reported by Hess et al. in NbSe 2 , is attributed to self-energy corrections of the normal electrons (in the core) caused by their coupling to excitations of the superconducting region (outside the core). The shape of the zero-bias anomaly is reproduced without benefit from adjustable parameters, though the predicted size is a little too large. If the critical currents in the superconducting region (outside the core) are recognized by letting the excitation density (at zero energy) be finite, then a perfect fit can be obtained

Chemical fingerprinting of hydrocarbon-contamination in soil

DEFF Research Database (Denmark)

Boll, Esther Sørensen; Nejrup, Jens; Jensen, Julie K.

2015-01-01

Chemical fingerprinting analyses of 29 hydrocarbon-contaminated soils were performed to assess the soil quality and determine the main contaminant sources. The results were compared to an assessment based on concentrations of the 16 priority polycyclic aromatic hydrocarbons pointed out by the U...... and in assessing weathering trends of hydrocarbon contamination in the soils. Multivariate data analysis of sum-normalized concentrations could as a stand-alone tool distinguish between hydrocarbon sources of petrogenic and pyrogenic origin, differentiate within petrogenic sources, and detect weathering trends....... Diagnostic ratios of PACs were not successful for source identification of the heavily weathered hydrocarbon sources in the soils. The fingerprinting of contaminated soils revealed an underestimation of PACs in petrogenic contaminated soils when the assessment was based solely on EPAPAH16. As alkyl...

Air-dust-borne associations of phototrophic and hydrocarbon-utilizing microorganisms: promising consortia in volatile hydrocarbon bioremediation.

Science.gov (United States)

Al-Bader, Dhia; Eliyas, Mohamed; Rayan, Rihab; Radwan, Samir

2012-11-01

Aquatic and terrestrial associations of phototrophic and heterotrophic microorganisms active in hydrocarbon bioremediation have been described earlier. The question arises: do similar consortia also occur in the atmosphere? Dust samples at the height of 15 m were collected from Kuwait City air, and analyzed microbiologically for phototrophic and heterotrophic hydrocarbon-utilizing microorganisms, which were subsequently characterized according to their 16S rRNA gene sequences. The hydrocarbon utilization potential of the heterotrophs alone, and in association with the phototrophic partners, was measured quantitatively. The chlorophyte Gloeotila sp. and the two cyanobacteria Nostoc commune and Leptolyngbya thermalis were found associated with dust, and (for comparison) the cynobacteria Leptolyngbya sp. and Acaryochloris sp. were isolated from coastal water. All phototrophic cultures harbored oil vapor-utilizing bacteria in the magnitude of 10(5) g(-1). Each phototrophic culture had its unique oil-utilizing bacteria; however, the bacterial composition in Leptolyngbya cultures from air and water was similar. The hydrocarbon-utilizing bacteria were affiliated with Acinetobacter sp., Aeromonas caviae, Alcanivorax jadensis, Bacillus asahii, Bacillus pumilus, Marinobacter aquaeolei, Paenibacillus sp., and Stenotrophomonas maltophilia. The nonaxenic cultures, when used as inocula in batch cultures, attenuated crude oil in light and dark, and in the presence of antibiotics and absence of nitrogenous compounds. Aqueous and diethyl ether extracts from the phototrophic cultures enhanced the growth of the pertinent oil-utilizing bacteria in batch cultures, with oil vapor as a sole carbon source. It was concluded that the airborne microbial associations may be effective in bioremediating atmospheric hydrocarbon pollutants in situ. Like the aquatic and terrestrial habitats, the atmosphere contains dust-borne associations of phototrophic and heterotrophic hydrocarbon

Development of in-core measuring method using optical techniques

International Nuclear Information System (INIS)

Kakuta, Tsunemi; Shikama, Tatsuo; Narui, Minoru; Sagawa, Tsutomu.

1994-01-01

Since applying to more severe radiation environments in nuclear plants, e.g., in-core measuring systems, diagnostics for fusion reactors, radiation related subjects should be considered by more severe radiation and environmental conditions. Owing to this, preliminary studies of heavy neutron irradiation effects on optical fibers are conducted in the core region of fission reactor. Two kinds of SiO 2 core optical fibers, highly pure SiO 2 with OH content core and SiO 2 with fluorine doped core, were irradiated in the core region of Japan Material Testing Reactor (JMTR). Both fibers were irradiated with fast neutron (E>1.0 MeV) fluence of about 1.6x10 19 n/cm 2 and gamma-ray doses of 3.3x10 9 Gy. The optical absorption and the light-emission spectrum were measured in-situ along the irradiation. This paper mainly outlines the fundamental effects of neutron irradiation and discuss the possibility of neutron detection in the core region of reactor. (J.P.N.)

Bioremediation: Technology for treating hydrocarbon-contaminated wastewater

Energy Technology Data Exchange (ETDEWEB)

Towprayoon, S.; Kuntrangwattana, S. [King Mongkut`s Institute of Technology, Bangkok (Thailand)

1996-12-31

Cutting oil wastewater from an iron and steel factory was applied to the soil windrow. Self-remediation was then compared with remediation with acclimatized indigenous microbes. The incremental reduction rate of the microorganisms and hydrocarbon-degradable microbes was slower in self-remediation than in the latter treatment. Within 30 days, when the acclimatized indigenous microbes were used, there was a significant reduction of the contaminated hydrocarbons, while self-remediation took longer to reduce to the same concentration. Various nitrogen sources were applied to the soil pile, namely, organic compost, chemical fertilizer, ammonium sulfate, and urea. The organic compost induced a high yield of hydrocarbon-degradable microorganisms, but the rate at which the cutting oil in the soil decreased was slower than when other nitrogen sources were used. The results of cutting oil degradation studied by gas chromatography showed the absence of some important hydrocarbons. The increment of the hydrocarbon-degradable microbes in the land treatment ecosystem does not necessarily correspond to the hydrocarbon reduction efficiency. 3 refs., 3 figs.

Biodegradation of petroleum hydrocarbons at low temperatures

International Nuclear Information System (INIS)

Whyte, L. G.; Greer, C W.

1999-01-01

Bioremediation of contaminated Arctic sites has been proposed as the logistically and economically most favorable solution despite the known technical difficulties. The difficulties involve the inhibition of pollutants removal by biodegradation below freezing temperatures and the relative slowness of the process to remove enough hydrocarbon pollutants during the above-freezing summer months. Despite these formidable drawbacks, biodegradation of hydrocarbon contaminants is possible even in below-zero temperatures, especially if indigenous psychrophilic and psychrotropic micro-organism are used. This paper reports results of a study involving several hydrocarbon-degrading psychrotropic bacteria and suggests bioaugmentation with specific cold-adapted organisms and/or biostimulation with commercial fertilizers for enhancing degradation of specific contaminants in soils from northern Canada. An evaluation of the biodegradation potential of hydrocarbon contaminated soils in the high Arctic suggested that the contaminated soils contained sufficient numbers of cold-adapted hydrocarbon-degrading bacteria and that the addition of fertilizer was sufficient to enhance the level of hydrocarbon degradation at low ambient summer temperatures. 9 refs., 2 tabs., 3 figs

Forming of the regional core transport network taking into account the allocation of alternative energy sources based on artificial intelligence methods

Directory of Open Access Journals (Sweden)

Marina ZHURAVSKAYA

2014-12-01

Full Text Available In the modern world the alternative energy sources, which considerably depend on a region, play more and more significant role. However, the transition of regions to new energy sources lead to the change of transport and logistic network configuration. The formation of optimal core transport network today is a guarantee of the successful economic development of a region tomorrow. The present article studies the issue of advanced core transport network development in a region based on the experience of European and Asian countries and the opportunity to adapt the best foreign experience to Russian conditions. On the basis of artificial intelligence methods for forest industry complex of Sverdlovskaya Oblast the algorithm of problem solution of an optimal logistic infrastructure allocation is offered and some results of a regional transport network are presented. These methods allowed to solve the set task in the conditions of information uncertainty. There are suggestions on the improvement of transport and logistic network in the territory of Sverdlovskaya Oblast. Traditionally the logistics of mineral fuel plays main role in regions development. Actually it is required to develop logistic strategic plans to be able to provide different possibilities of power-supply, flexible enough to change with the population density, transport infrastructure and demographics of different regions. The problem of logistic centers allocation was studied by many authors. The approach, offered by the authors of this paper is to solve the set of tasks by applying artificial intelligence methods, such as fuzzy set theory and genetic algorithms.

FTIR Study of Comustion Species in Several Regions of a Candle Flame

Science.gov (United States)

White, Allen R.

2013-06-01

The complex chemical structure of the fuel in a candle flame, parafin, is broken down into smaller hydrocarbons in the dark region just above the candle wick during combustion. This creates fuel-rich, fuel-lean, hydrocarbon reaction, and combustion product regions in the flame during combustion that are spectroscopically rich, particularly in the infrared. IR emissions were measured for each reaction region via collection optics focused into an FTIR and used to identify IR active species present in that region and, when possible, temperature of the sampling region. The results of the measurements are useful for combustion reaction modeling as well as for future validation of mass spectroscopy sampling systems.

Core concepts for ''zero-sodium-void-worth core'' in metal fuelled fast reactor

International Nuclear Information System (INIS)

Chang, Y.I.; Hill, R.N.; Fujita, E.K.; Wade, D.C.; Kumaoka, Y.; Suzuki, M.; Kawashima, M.; Nakagawa, H.

1991-01-01

Core design options to reduce the sodium void worth in metal fueled LMRs are investigated. Two core designs which achieve a zero sodium void worth are analyzed in detail. The first design is a ''pancaked'' and annular core with enhanced transuranic burning capabilities; the high leakage in this design yields a low breeding ratio and small void worth. The second design is an axially multilayered annular core which is fissile self-sufficient; in this design, the upper and lower core regions are neutronically decoupled for reduced void worth while fissile self-sufficiency is achieved using internal axial blankets plus external radial and axial blanket zones. The neutronic performance characteristics of these low void worth designs are assessed here; their passive safety properties are discussed in a companion paper. 16 refs., 2 figs., 3 tabs

Core concepts for 'zero-sodium-void-worth core' in metal fuelled fast reactor

International Nuclear Information System (INIS)

Chang, Y.I.; Hill, R.N.; Fujita, E.K.; Wade, D.C.; Kumaoka, Y.; Suzuki, M.; Kawashima, M.; Nakagawa, H.

1991-01-01

Core design options to reduce the sodium void worth in metal fuelled LMRs are investigated. Two core designs which achieve a zero sodium void worth are analyzed in detail. The first design is a 'pancaked' and annular core with enhanced transuranic burning capabilities; the high leakage in this design yields a low breeding ratio and small void worth. The second design is an axially multilayered annular core which is fissile self-sufficient; in this design, the upper and lower core regions are neutronically decoupled for reduced void worth while fissile self-sufficiency is achieved using internal axial blankets plus external radial and axial blanket-zones. The neutronic performance characteristics of these low void worth designs are assessed here; their passive safety properties are discussed in a companion paper. (author)

Process for in-situ biodegradation of hydrocarbon contaminated soil

International Nuclear Information System (INIS)

Ely, D.L.; Heffner, D.A.

1991-01-01

This patent describes an in situ process for biodegrading hydrocarbons by drawing oxygen into an undisturbed hydrocarbon contaminated zone in a fluid permeable soil. It comprises: establishing a borehole extending from the earth's surface through a hydrocarbon contaminated zone having hydrocarbon degrading microbes therein; lining the borehole with a fluid impermeable liner coaxially spaced and sealingly connected to the inside surface of the borehole and extending from the earth's surface to the hydrocarbon-contaminated zone; the liner including a fluid permeable portion extending from the lower end thereof and through at least a portion of the hydrocarbon contaminated zone, fluidly connecting a source of negative pressure to the fluid impermeable line; evacuating gas from the borehole through the fluid permeable portion of the liner at a rate sufficient to draw air from the earth's surface into the hydrocarbon containing zone; and adjusting the flow rate of the evacuated gas so that the amount of hydrocarbon biodegradation therein is within 50% of the maximum hydrocarbon biodegradation rate as detected by the volume of carbon dioxide in the evacuated gas

Chemical characterization and spatial distribution of PAHs and heavy hydrocarbons in rural sites of Campania Region, South Italy.

Science.gov (United States)

Monaco, D; Riccio, A; Chianese, E; Adamo, P; Di Rosa, S; Fagnano, M

2015-10-01

In this paper, the behaviour and distribution patterns of heavy hydrocarbons and several polycyclic aromatic hydrocarbon (PAH) priority pollutants, as listed by the US Environmental Protection Agency, were evaluated in 891 soil samples. The samples were collected in three expected polluted rural sites in Campania (southern Italy) as part of the LIFE11 ECOREMED project, funded by the European Commission, to test innovative agriculture-based soil restoration techniques. These sites have been selected because they have been used for the temporary storage of urban and building waste (Teverola), subject to illicit dumping of unknown material (Trentola-Ducenta), or suspected to be polluted by metals due to agricultural practices (Giugliano). Chemical analysis of soil samples allowed the baseline pollution levels to be determined prior to any intervention. It was found that these areas can be considered contaminated for residential use, in accordance with Italian environmental law (Law Decree 152/2006). Statistical analysis applied to the data proved that average mean concentrations of heavy hydrocarbons could be as high as 140 mg/kg of dry soil with peaks of 700 mg/kg of dry soil, for the Trentola-Ducenta site; the median concentration of analytical results for hydrocarbon (HC) concentration for the Trentola-Ducenta and Giugliano sites was 63 and 73.4 mg/kg dry soil, respectively; for Teverola, the median level was 35 mg/kg dry soil. Some PAHs (usually benzo(a)pyrene) also exceeded the maximum allowed level in all sites. From the principal component analysis applied to PAH concentrations, it emerged that pollutants can be supposed to derive from a single source for the three sites. Diagnostic ratios calculated to determine possible PAH sources suggest petroleum combustion or disposal practice. Our sampling protocol also showed large dishomogeneity in soil pollutant spatial distribution, even at a scale as small as 3.3 m, indicating that variability could emerge at very

The core health science library in Canada.

Science.gov (United States)

Huntley, J L

1974-04-01

Core lists in Canada are characterized by regional differences. The lists of current importance are: (1) the British Columbia acquisitions guide for hospital libraries, (2) three Saskatchewan lists for hospitals of different sizes, (3) a core list recommended for Ontario hospitals, (4) Quebec core lists, including French language lists.

POLYCYCLIC AROMATIC HYDROCARBON FAR-INFRARED SPECTROSCOPY

International Nuclear Information System (INIS)

Boersma, C.; Mattioda, A. L.; Tielens, A. G. G. M.; Allamandola, L. J.; Bauschlicher, C. W. Jr; Ricca, A.; Peeters, E.

2011-01-01

The far-IR characteristics of astrophysically relevant polycyclic aromatic hydrocarbons (PAHs) averaging in size around 100 carbon atoms have been studied using the theoretical spectra in the NASA Ames PAH IR Spectroscopic Database. These spectra were calculated using density functional theory. Selections of PAH species are made, grouped together by common characteristics or trends, such as size, shape, charge, and composition, and their far-IR spectra compared. The out-of-plane modes involving the entire molecule are explored in detail, astronomical relevance is assessed, and an observing strategy is discussed. It is shown that PAHs produce richer far-IR spectra with increasing size. PAHs also produce richer far-IR spectra with increasing number of irregularities. However, series of irregular-shaped PAHs with the same compact core have common 'Jumping-Jack' modes that 'pile up' at specific frequencies in their average spectrum. For the PAHs studied here, around 100 carbon atoms in size, this band falls near 50 μm. PAH charge and nitrogen inclusion affect band intensities but have little effect on far-IR band positions. Detailed analysis of the two-dimensional, out-of-plane bending 'drumhead' modes in the coronene and pyrene 'families' and the one-dimensional, out-of-plane bending 'bar' modes in the acene 'family' show that these molecular vibrations can be treated as classical vibrating sheets and bars of graphene, respectively. The analysis also shows that the peak position of these modes is very sensitive to the area of the emitting PAH and does not depend on the particular geometry. Thus, these longest wavelength PAH bands could provide a unique handle on the size of the largest species in the interstellar PAH family. However, these bands are weak. Observing highly excited regions showing the mid-IR bands in which the emission from classical dust peaks at short wavelengths offers the best chance of detecting PAH emission in the far-IR. For these regions

Polycyclic Aromatic Hydrocarbon Far-infrared Spectroscopy

Science.gov (United States)

Boersma, C.; Bauschlicher, C. W., Jr.; Ricca, A.; Mattioda, A. L.; Peeters, E.; Tielens, A. G. G. M.; Allamandola, L. J.

2011-03-01

The far-IR characteristics of astrophysically relevant polycyclic aromatic hydrocarbons (PAHs) averaging in size around 100 carbon atoms have been studied using the theoretical spectra in the NASA Ames PAH IR Spectroscopic Database. These spectra were calculated using density functional theory. Selections of PAH species are made, grouped together by common characteristics or trends, such as size, shape, charge, and composition, and their far-IR spectra compared. The out-of-plane modes involving the entire molecule are explored in detail, astronomical relevance is assessed, and an observing strategy is discussed. It is shown that PAHs produce richer far-IR spectra with increasing size. PAHs also produce richer far-IR spectra with increasing number of irregularities. However, series of irregular-shaped PAHs with the same compact core have common "Jumping-Jack" modes that "pile up" at specific frequencies in their average spectrum. For the PAHs studied here, around 100 carbon atoms in size, this band falls near 50 μm. PAH charge and nitrogen inclusion affect band intensities but have little effect on far-IR band positions. Detailed analysis of the two-dimensional, out-of-plane bending "drumhead" modes in the coronene and pyrene "families" and the one-dimensional, out-of-plane bending "bar" modes in the acene "family" show that these molecular vibrations can be treated as classical vibrating sheets and bars of graphene, respectively. The analysis also shows that the peak position of these modes is very sensitive to the area of the emitting PAH and does not depend on the particular geometry. Thus, these longest wavelength PAH bands could provide a unique handle on the size of the largest species in the interstellar PAH family. However, these bands are weak. Observing highly excited regions showing the mid-IR bands in which the emission from classical dust peaks at short wavelengths offers the best chance of detecting PAH emission in the far-IR. For these regions

[Compositions and residual properties of petroleum hydrocarbon in contaminated soil of the oilfields].

Science.gov (United States)

Hu, Di; Li, Chuan; Dong, Qian-Qian; Li, Li-Ming; Li, Guang-He

2014-01-01

The aims of this study were to determine the compositions and residual properties of petroleum hydrocarbon in soil, as well as to identify the source and weathering degree of the pollution. A total of 5 producing wells in Gudao and Hekou oil producing region of Shengli oilfields were analyzed. More than 50 individual target compounds including straight-and branched-chain alkanes( n-alkanes, pristine and phytane) and polycyclic aromatic hydrocarbons (PAHs) in soil samples and crude oil were determined by gas chromatography-mass spectrometry (GC-MS). The percentages of chain alkanes and PAHs in total solvent extractable matters(TSEM) of soil samples were both much lower than those in the crude oil samples. The compositions of petroleum hydrocarbon in soil samples differed from those in crude oil, which indicated the n-alkanes with carbon numbers contaminated soils, the relationship between the index and petroleum hydrocarbon compounds was analyzed using principal component analysis (PCA). The results showed that the n-alkanes with carbon numbers > 33 and the PAHs with rings between 3 and 5 were much harder to degrade. PCA of 4 indexes for source identification revealed more than 50% of the soil samples were polluted by crude oil, which needs more attention during remediation.

Assessing impediments to hydrocarbon biodegradation in weathered contaminated soils.

Science.gov (United States)

Adetutu, Eric; Weber, John; Aleer, Sam; Dandie, Catherine E; Aburto-Medina, Arturo; Ball, Andrew S; Juhasz, Albert L

2013-10-15

In this study, impediments to hydrocarbon biodegradation in contaminated soils were assessed using chemical and molecular methodologies. Two long-term hydrocarbon contaminated soils were utilised which were similar in physico-chemical properties but differed in the extent of hydrocarbon (C10-C40) contamination (S1: 16.5 g kg(-1); S2: 68.9 g kg(-1)). Under enhanced natural attenuation (ENA) conditions, hydrocarbon biodegradation was observed in S1 microcosms (26.4% reduction in C10-C40 hydrocarbons), however, ENA was unable to stimulate degradation in S2. Although eubacterial communities (PCR-DGGE analysis) were similar for both soils, the alkB bacterial community was less diverse in S2 presumably due to impacts associated with elevated hydrocarbons. When hydrocarbon bioaccessibility was assessed using HP-β-CD extraction, large residual concentrations remained in the soil following the extraction procedure. However, when linear regression models were used to predict the endpoints of hydrocarbon degradation, there was no significant difference (P>0.05) between HP-β-CD predicted and microcosm measured biodegradation endpoints. This data suggested that the lack of hydrocarbon degradation in S2 resulted primarily from limited hydrocarbon bioavailability. Copyright © 2013 Elsevier B.V. All rights reserved.

Problems of hydrocarbon resources development in new bedding zones

International Nuclear Information System (INIS)

Egorov, O.I.; Koszhanov, A.K.

1997-01-01

Intensive exploring geological surveying works were carried out for revealing of fuel resources in South Kazakhstan. Number of complex gas deposits - Ajrakty, Amangel'dy, Kumyrly and others as well as Northern Usharly and Usharal-Kemirtobe deposits of nitrogen-helium gas are recovered. Introduction its into operation has significant importance in consequence of urgent fuel deficit in region. Basic way of guaranteed gas supply to industry and population of South Kazakhstan is connected with own hydrocarbon fields development

Geochemical assessment of light gaseous hydrocarbons in near-surface soils of Kutch-Saurashtra: Implication for hydrocarbon prospects

Science.gov (United States)

Rao, P. Lakshmi Srinivasa; Madhavi, T.; Srinu, D.; Kalpana, M. S.; Patil, D. J.; Dayal, A. M.

2013-02-01

Light hydrocarbons in soil have been used as direct indicators in geochemical hydrocarbon exploration, which remains an unconventional path in the petroleum industry. The occurrence of adsorbed soil gases, methane and heavier homologues were recorded in the near-surface soil samples collected from Kutch-Saurashtra, India. Soil gas alkanes were interpreted to be derived from deep-seated hydrocarbon sources and have migrated to the surface through structural discontinuities. The source of hydrocarbons is assessed to be thermogenic and could have been primarily derived from humic organic matter with partial contribution from sapropelic matter. Gas chromatographic analyses of hydrocarbons desorbed from soil samples through acid extraction technique showed the presence of methane through n-butane and the observed concentrations (in ppb) vary from: methane (C1) from 4-291, ethane (C2) from 0-84, propane (C3) from 0-37, i-butane (iC4) from 0-5 and n-butane (nC4) from 0-4. Carbon isotopes measured for methane and ethane by GC-C-IRMS, range between -42.9‰ to -13.3‰ (Pee Dee Belemnite - PDB) and -21.2‰ to -12.4‰ (PDB), respectively. The increased occurrence of hydrocarbons in the areas near Anjar of Kutch and the area south to Rajkot of Saurashtra signifies the area potential for oil and gas.

In-situ hydrocarbon delineation using laser-induced fluorescence

International Nuclear Information System (INIS)

Taer, A.D.; Hastings, R.W.; Brown, A.Y.; Frend, R.

1996-01-01

An investigation of hydrocarbons in soils was conducted at an active Shell Oil Company petroleum products terminal, located in Carson, California. An investigation approach involving Laser-Induced Fluorescence (LIF) and Cone Penetrometer Testing (CPT) technologies was implemented to provide real-time, in-situ characterization of site stratigraphy, hydrocarbon distribution and importantly, hydrocarbon product differentiation. The area of investigation is located along a property boundary, where a plume of separate phase hydrocarbons has been actively recovered for several years. CPT/LIF technology was selected for the investigation since previous delineation efforts using hydrocarbon fingerprinting methods proved inconclusive. Additionally, the CPT/LIF technology had the potential to provide a cost effective solution to accomplish project objectives. Based on the information obtained during this investigation, it was determined that the plume of separate phase hydrocarbons along the northern property boundary is from a source distinctly different than any identified hydrocarbons known to be from on-site sources. In addition, the plume was determined to not be connected with any other known on-site hydrocarbon plumes. The results of this CPT/LIF investigation were consistent with the known hydrogeologic conditions. This evaluation determined that CPT/LIF technology was very effective in addressing project objectives and resulted in a significant cost savings

Constructed wetlands for treatment of dissolved phase hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Moore, B J; Ross, S D [Komex International, Calgary, AB (Canada); Gibson, D [Calgary Univ., AB (Canada); Hardisty, P E [Komex Clarke Bond, Bristol (United Kingdom)

1999-01-01

The use of constructed wetlands as an alternative to conventional treatment of condensate-contaminated groundwater was studied. In 1997 a pilot scale wetland was constructed and implemented at the Gulf Strachan Gas Processing Plant to determine its ability in treating extracted groundwater contaminated with natural gas condensates. This paper presented the results of hydrocarbon removal efficiency, hydrocarbon removal mechanisms, winter operation, and the effect of hydrocarbons on vegetation health. The inflow water to the wetland contains 15 to 20 mg/L of C[sub 5]-C[sub 10] hydrocarbons, including 50 per cent BTEX compounds. During the summer months, hydrocarbon removal efficiency was 100 per cent, but decreased to 60 and 30 per cent in the spring and late fall, respectively. The hydrocarbons not removed in the wetland were eventually removed along the outflow channel. Temperature was determined to be an important factor in the variable removal rates, particularly when there is no aeration. The main hydrocarbon removal mechanisms appear to be volatilization, biodegradation and dilution. At present, plant uptake is not a factor. 12 refs., 1 tab., 3 figs.

Constructed wetlands for treatment of dissolved phase hydrocarbons

International Nuclear Information System (INIS)

Moore, B.J.; Ross, S.D.; Gibson, D.; Hardisty, P.E.

1999-01-01

The use of constructed wetlands as an alternative to conventional treatment of condensate-contaminated groundwater was studied. In 1997 a pilot scale wetland was constructed and implemented at the Gulf Strachan Gas Processing Plant to determine its ability in treating extracted groundwater contaminated with natural gas condensates. This paper presented the results of hydrocarbon removal efficiency, hydrocarbon removal mechanisms, winter operation, and the effect of hydrocarbons on vegetation health. The inflow water to the wetland contains 15 to 20 mg/L of C 5 -C 10 hydrocarbons, including 50 per cent BTEX compounds. During the summer months, hydrocarbon removal efficiency was 100 per cent, but decreased to 60 and 30 per cent in the spring and late fall, respectively. The hydrocarbons not removed in the wetland were eventually removed along the outflow channel. Temperature was determined to be an important factor in the variable removal rates, particularly when there is no aeration. The main hydrocarbon removal mechanisms appear to be volatilization, biodegradation and dilution. At present, plant uptake is not a factor. 12 refs., 1 tab., 3 figs

Saturated versus unsaturated hydrocarbon interactions with carbon nanostructures

Directory of Open Access Journals (Sweden)

Deivasigamani eUmadevi

2014-09-01

Full Text Available The interactions of various acyclic and cyclic hydrocarbons in both saturated and unsaturated forms with the carbon nanostructures (CNSs have been explored by using density functional theory (DFT calculations. Model systems representing armchair and zigzag carbon nanotubes (CNTs and graphene have been considered to investigate the effect of chirality and curvature of the CNSs towards these interactions. Results of this study reveal contrasting binding nature of the acyclic and cyclic hydrocarbons towards CNSs. While the saturated molecules show stronger binding affinity in acyclic hydrocarbons; the unsaturated molecules exhibit higher binding affinity in cyclic hydrocarbons. In addition, acyclic hydrocarbons exhibit stronger binding affinity towards the CNSs when compared to their corresponding cyclic counterparts. The computed results excellently corroborate the experimental observations. The interaction of hydrocarbons with graphene is more favourable when compared with CNTs. Bader’s theory of atoms in molecules has been invoked to characterize the noncovalent interactions of saturated and unsaturated hydrocarbons. Our results are expected to provide useful insights towards the development of rational strategies for designing complexes with desired noncovalent interaction involving CNSs.

Hydrocarbon preservation conditions in Mesozoic–Paleozoic marine strata in the South Yellow Sea Basin

Directory of Open Access Journals (Sweden)

Jie Liang

2017-11-01

Full Text Available In the South Yellow Sea Basin, Mesozoic–Paleozoic marine strata are generally well developed with large thickness, and they are characterized by multi-source and multi-stage hydrocarbon accumulation, providing a material basis for the formation of large-scale oil and gas fields. However, no substantial breakthrough has been made in this area. Based on previous research results, the complex tectonic pattern of this superimposed basin was formed by multi-stage tectonic movements and the favorable static conditions for hydrocarbon preservation were reworked or destroyed by later superimposition. Therefore, hydrocarbon preservation conditions are the key factors for restricting the breakthrough of marine oil and gas exploration in this area. In this paper, hydrocarbon preservation conditions of marine strata in the South Yellow Sea Basin were comprehensively analyzed from many aspects, such as tectonic movement, source conditions, caprock characteristics, magmatic activities, and hydrogeological and hydrogeochemical characteristics. It is indicated that the complex tectonic pattern of the South Yellow Sea Basin is resulted from tectonic events in multiple stages, and the development and evolution of regional source rocks are mainly controlled by two stages (i.e., the stable evolution stage of Mesozoic–Paleozoic marine basin and the Mesozoic–Cenozoic tectonic pattern transformation and basin formation stage, so the characteristics of differential oil and gas preservation are presented. Besides, better marine hydrocarbon preservation preconditions in this area are weaker tectonic reworking, development of high-quality thick source rocks, good vertical sealing capacity of caprocks, weaker magmatic activity and confined hydrogeological conditions. It is concluded that the Laoshan Uplift in the central part of the South Yellow Sea Basin is structurally stable with weaker faulting and magmatic activities, so it is better in oil and gas preservation

Radiolysis of hydrocarbons in liquid phase (Modern state of problem)

International Nuclear Information System (INIS)

Saraeva, V.V.

1986-01-01

Problems of ionizing radiation effect on hydrocarbons and hydrocarbon systems in a liquid phase are considered. Modern representations on the mechanism of hydrocarbon radiolysis are presented. Electron moderation and ion-electron pair formation, behaviour of charged particles, excited states, radical formation and their reactions are discussed. Behaviour of certain hydrocarbon classes: alkanes, cyclic hydrocarbons, olefines, aromatic hydrocarbons as well as different hydrocarbon mixtures is considered in detail. Radiation-chemical changes in organic coolants and ways of increasing radiation resistance are considered. Polyphenyl compounds are noted to be most perspective here

Hydrocarbon studies in Puget Sound and off the Washington coast. Progress report, March 1978--February 1979

International Nuclear Information System (INIS)

Carpenter, R.; Fairhall, A.W.

1979-01-01

This report summarizes the past year's progress in our studies of the amounts, types, and probable origins of aliphatic, aromatic, S-, and N-containing hydrocarbons in sediments, organisms, and waters of Puget Sound and the Washington coast. We are trying to identify the relative importance of the various possible sources of these substances, the major pathways by which they are transferred through some parts of the marine food web, their rates of transfer, and their ultimate fates. We have found that changes in aliphatic and aromatic hydrocarbon compositions are evident in 210 Pb-dated sediment cores from central Puget Sound. These changes are due both to natural diagenetic processes and to low-level inputs of fossil fuels from a variety of sources. We have found measurable amounts of both S- and N-containing compounds in these Puget Sound sediments. Our studies of the role of zooplankton fecal pellets in the cycling of trace chemicals in the sea have shown that fecal pellets are an important vertical transport agent for hydrocarbons in the sea. We now have defined the natural variations in 14 C and 13 C/ 12 C isotope ratios of the inorganic carbon in Puget Sound seawater. Carbon isotope abundances for organisms and sediments are also reported for selected sites

MODELING GALACTIC EXTINCTION WITH DUST AND 'REAL' POLYCYCLIC AROMATIC HYDROCARBONS

Energy Technology Data Exchange (ETDEWEB)

Mulas, Giacomo; Casu, Silvia; Cecchi-Pestellini, Cesare [INAF-Osservatorio Astronomico di Cagliari, Strada n.54, Loc. Poggio dei Pini, I-09012 Capoterra (Italy); Zonca, Alberto, E-mail: gmulas@oa-cagliari.inaf.it, E-mail: silvia@oa-cagliari.inaf.it, E-mail: ccp@oa-cagliari.inaf.it, E-mail: azonca@oa-cagliari.inaf.it [Dipartimento di Fisica, Universita di Cagliari, Strada Prov.le Monserrato-Sestu Km 0.700, I-09042 Monserrato (Italy)

2013-07-01

We investigate the remarkable apparent variety of galactic extinction curves by modeling extinction profiles with core-mantle grains and a collection of single polycyclic aromatic hydrocarbons. Our aim is to translate a synthetic description of dust into physically well-grounded building blocks through the analysis of a statistically relevant sample of different extinction curves. All different flavors of observed extinction curves, ranging from the average galactic extinction curve to virtually 'bumpless' profiles, can be described by the present model. We prove that a mixture of a relatively small number (54 species in 4 charge states each) of polycyclic aromatic hydrocarbons can reproduce the features of the extinction curve in the ultraviolet, dismissing an old objection to the contribution of polycyclic aromatic hydrocarbons to the interstellar extinction curve. Despite the large number of free parameters (at most the 54 Multiplication-Sign 4 column densities of each species in each ionization state included in the molecular ensemble plus the 9 parameters defining the physical properties of classical particles), we can strongly constrain some physically relevant properties such as the total number of C atoms in all species and the mean charge of the mixture. Such properties are found to be largely independent of the adopted dust model whose variation provides effects that are orthogonal to those brought about by the molecular component. Finally, the fitting procedure, together with some physical sense, suggests (but does not require) the presence of an additional component of chemically different very small carbonaceous grains.

Production of hydrocarbons of value

Energy Technology Data Exchange (ETDEWEB)

1931-06-16

A process is described for the production of hydrocarbons of great value by treating with heat and pressure carbonaceous materials such as coals, tars, mineral oils, and products of distillation and transformation of these materials, also for the refining with heat and pressure of mixed liquid hydrocarbons by means of hydrogen gas, preferably in the presence of catalysts, consisting in using as the hydrogenating gas that obtained by gasification of combustible solids after partial or complete cleaning at atmospheric or elevated pressures, by means of solid adsorbents, chemical agents or catalysts, or mixtures of these agents, the hydrocarbons being characterized by strong unsaturation, and the presence of oxygen, sulfur compounds, and oxides of nitrogen.

Total Petroleum Hydrocarbons (TPH): ToxFAQs

Science.gov (United States)

... a state: This map displays locations where Total Petroleum Hydrocarbons (TPH) is known to be present. On ... I get more information? ToxFAQs TM for Total Petroleum Hydrocarbons (TPH) ( Hidrocarburos Totales de Petróleo (TPH) ) August ...

Offshore hydrocarbon resources in the Arctic: from cooperation to confrontation in an era of geopolitical and economic turbulence?

OpenAIRE

Morgunova, Maria; Westphal, Kirsten

2016-01-01

The Arctic region has been an area of low tension since the end of the Cold War. This observation is important because the run on hydrocarbons in the Arctic has not resulted in increased rivalries as expected. The outcomes have been international joint ventures in oil and gas project on the economic side and a strengthening of Arctic governance in the political realm. Since 2014, the situation has changed rapidly. Economic interests in hydrocarbon development are increasingly diverging betwee...

The Charge State of Polycyclic Aromatic Hydrocarbons across a Reflection Nebula, an H II Region, and a Planetary Nebula

Science.gov (United States)

Boersma, C.; Bregman, J.; Allamandola, L. J.

2018-05-01

Low-resolution Spitzer-IRS spectral map data of a reflection nebula (NGC 7023), H II region (M17), and planetary nebula (NGC 40), totaling 1417 spectra, are analyzed using the data and tools available through the NASA Ames PAH IR Spectroscopic Database. The polycyclic aromatic hydrocarbon (PAH) emission is broken down into PAH charge and size subclass contributions using a database-fitting approach. The resulting charge breakdown results are combined with those derived using the traditional PAH band strength ratio approach, which interprets particular PAH band strength ratios as proxies for PAH charge. Here the 6.2/11.2 μm PAH band strength ratio is successfully calibrated against its database equivalent: the {n}PAH}+}/{n}PAH}0} ratio. In turn, this ratio is converted into the PAH ionization parameter, which relates it to the strength of the radiation field, gas temperature, and electron density. Population diagrams are used to derive the {{{H}}}2 density and temperature. The bifurcated plot of the 8.6 versus 11.2 μm PAH band strength for the northwest photo dissociation region in NGC 7023 is shown to be a robust diagnostic template for the {n}PAH}+}/{n}PAH}0} ratio in all three objects. Template spectra for the PAH charge and size subclasses are determined for each object and shown to favorably compare. Using the determined template spectra from NGC 7023 to fit the emission in all three objects yields, upon inspection of the Structure SIMilarity maps, satisfactory results. The choice of extinction curve proves to be critical. Concluding, the distinctly different astronomical environments of a reflection nebula, H II region, and planetary nebula are reflected in their PAH emission spectra.

Observations of exotic inner core waves

NARCIS (Netherlands)

Waszek, Lauren; Deuss, A.F.|info:eu-repo/dai/nl/412396610

2015-01-01

The seismic structure of Earth’s inner core is highly complex, displaying strong anisotropy and further regional variations. However, few seismic waves are sensitive to the inner core and fundamental questions regarding the origin of the observed seismic features remain unanswered. Thus, new

The offshore hydrocarbon releases (HCR) database

International Nuclear Information System (INIS)

Bruce, R.A.P.

1995-01-01

Following Cullen Recommendation 39 which states that: ''The regulatory body should be responsible for maintaining a database with regard to hydrocarbon leaks, spills, and ignitions in the Industry and for the benefit of Industry'', HSE Offshore Safety Division (HSE-OSD) has now been operating the Hydrocarbon Releases (HCR) Database for approximately 3 years. This paper deals with the reporting of Offshore Hydrocarbon Releases, the setting up of the HCR Database, the collection of associated equipment population data, and the main features and benefits of the database, including discussion on the latest output information. (author)

Sustainable treatment of hydrocarbon-contaminated industrial land

OpenAIRE

Cunningham, Colin John

2012-01-01

Land contamination by petroleum hydrocarbons is a widespread and global environmental pollution issue from recovery and refining of crude oil and the ubiquitous use of hydrocarbons in industrial processes and applications. Sustainable treatment of hydrocarbon-contaminated industrial land was considered with reference to seven published works on contaminated railway land including the track ballast, crude oil wastes and contaminated refinery soils. A methodology was developed...

Stable water isotopes of precipitation and firn cores from the northern Antarctic Peninsula region as a proxy for climate reconstruction

Directory of Open Access Journals (Sweden)

F. Fernandoy

2012-03-01

Full Text Available In order to investigate the climate variability in the northern Antarctic Peninsula region, this paper focuses on the relationship between stable isotope content of precipitation and firn, and main meteorological variables (air temperature, relative humidity, sea surface temperature, and sea ice extent. Between 2008 and 2010, we collected precipitation samples and retrieved firn cores from several key sites in this region. We conclude that the deuterium excess oscillation represents a robust indicator of the meteorological variability on a seasonal to sub-seasonal scale. Low absolute deuterium excess values and the synchronous variation of both deuterium excess and air temperature imply that the evaporation of moisture occurs in the adjacent Southern Ocean. The δ¹⁸O-air temperature relationship is complicated and significant only at a (multiseasonal scale. Backward trajectory calculations show that air-parcels arriving at the region during precipitation events predominantly originate at the South Pacific Ocean and Bellingshausen Sea. These investigations will be used as a calibration for ongoing and future research in the area, suggesting that appropriate locations for future ice core research are located above 600 m a.s.l. We selected the Plateau Laclavere, Antarctic Peninsula as the most promising site for a deeper drilling campaign.

Task-based core-periphery organization of human brain dynamics.

Directory of Open Access Journals (Sweden)

Danielle S Bassett

Full Text Available As a person learns a new skill, distinct synapses, brain regions, and circuits are engaged and change over time. In this paper, we develop methods to examine patterns of correlated activity across a large set of brain regions. Our goal is to identify properties that enable robust learning of a motor skill. We measure brain activity during motor sequencing and characterize network properties based on coherent activity between brain regions. Using recently developed algorithms to detect time-evolving communities, we find that the complex reconfiguration patterns of the brain's putative functional modules that control learning can be described parsimoniously by the combined presence of a relatively stiff temporal core that is composed primarily of sensorimotor and visual regions whose connectivity changes little in time and a flexible temporal periphery that is composed primarily of multimodal association regions whose connectivity changes frequently. The separation between temporal core and periphery changes over the course of training and, importantly, is a good predictor of individual differences in learning success. The core of dynamically stiff regions exhibits dense connectivity, which is consistent with notions of core-periphery organization established previously in social networks. Our results demonstrate that core-periphery organization provides an insightful way to understand how putative functional modules are linked. This, in turn, enables the prediction of fundamental human capacities, including the production of complex goal-directed behavior.

Hydrocarbon toxicity: an analysis of AAPCC TESS data.

Science.gov (United States)

Cobaugh, Daniel J; Seger, Donna L; Krenzelok, Edward P

2007-01-01

Human hydrocarbon exposures have the potential to cause significant morbidity and mortality. To determine which hydrocarbons were associated with the most severe adverse outcomes, human exposure data reported to American poison information centers were analyzed. Outcome data for single-substance, hydrocarbon exposures reported to the American Association of Poison Control Centers Toxic Exposure Surveillance System from 1994 through 2003 were analyzed. Only cases with definitive medical outcomes were included. Analyses were stratified by five age groups: 59 years. Hazard factors were determined by calculating the sum of the major effects and fatalities for each hydrocarbon category and dividing this by the total number of exposures for that category. To normalize the data, the overall rate of major effects and deaths for each age group was assigned hazard factor value of 1. Hydrocarbon categories with a HF of > or = 1.5 were included in the final analyses. Estimated rates of major effect and fatal outcomes (outcomes/1000 people) were also calculated. 318,939 exposures were analyzed. Exposures to benzene, toluene/xylene, halogenated hydrocarbons, kerosene and lamp oil resulted in the highest hazard factor values. These data demonstrate that hydrocarbons that are absorbed systemically and those with low viscosities are associated with higher hazard factors. The risks associated with hydrocarbons often implicated in abuse by older children and adolescents are also confirmed.

Thermophilic slurry-phase treatment of petroleum hydrocarbon waste sludges

International Nuclear Information System (INIS)

Castaldi, F.J.; Bombaugh, K.J.; McFarland, B.

1995-01-01

Chemoheterotrophic thermophilic bacteria were used to achieve enhanced hydrocarbon degradation during slurry-phase treatment of oily waste sludges from petroleum refinery operations. Aerobic and anaerobic bacterial cultures were examined under thermophilic conditions to assess the effects of mode of metabolism on the potential for petroleum hydrocarbon degradation. The study determined that both aerobic and anaerobic thermophilic bacteria are capable of growth on petroleum hydrocarbons. Thermophilic methanogenesis is feasible during the degradation of hydrocarbons when a strict anaerobic condition is achieved in a slurry bioreactor. Aerobic thermophilic bacteria achieved the largest apparent reduction in chemical oxygen demand, freon extractable oil, total and volatile solid,s and polycyclic aromatic hydrocarbons (PAHs) when treating oily waste sludges. The observed shift with time in the molecular weight distribution of hydrocarbon material was more pronounced under aerobic metabolic conditions than under strict anaerobic conditions. The changes in the hydrocarbon molecular weight distribution, infrared spectra, and PAH concentrations during slurry-phase treatment indicate that the aerobic thermophilic bioslurry achieved a higher degree of hydrocarbon degradation than the anaerobic thermophilic bioslurry during the same time period

Non conventional hydrocarbons in Maghreb - an announced ecocide

International Nuclear Information System (INIS)

Balvet, Jacqueline; Espagne, Vincent; Rondeleux, Nejma; Dupont, Stephane

2015-01-01

Whereas gas and oil companies did not succeed in the development of shale gas exploration and exploitation in Europe for different reasons (citizen mobilisation against these projects, resources much smaller than expected), these companies are looking in other directions, notably the Maghreb region (North Africa) which is an important hydrocarbon supplier for European countries. This publication proposes an overview of the situation in Algeria, Morocco and Tunisia regarding this exploitation. It first recalls health and pollution impacts and consequences of hydraulic fracturing, and also the impact of hydrocarbon consumption on climate change. It indicates assessments made by the EIA of resources of shale gas and shale oil in the three countries, and outlines that these assessments might be too high as it has been the case in other countries. An overview of the situation of the three countries is then proposed, starting with Algeria: the third world shale gas reserve, presence of Total and GDF-Suez as investors with Sonatrach (the Algerian company) keeping a large majority, existence of a law which authorises the exploitation of non conventional hydrocarbons, and a very strong mobilisation of populations in the Algerian Sahara. The case of Morocco is then addressed: high dependence on imports but important non conventional reserves, exploitation of several sites, good conditions awarded to multinational companies, a focus on two important investors (Chevron and Repsol), start of a citizen mobilisation. The case of Tunisia is finally addressed: discovery of 'miraculous' deposits, overview of investors, a new but absolutely iniquitous legal framework, mobilisation of local associations

Application of magnetic techniques to lateral hydrocarbon migration - Lower Tertiary reservoir systems, UK North Sea

Science.gov (United States)

Badejo, S. A.; Muxworthy, A. R.; Fraser, A.

2017-12-01

Pyrolysis experiments show that magnetic minerals can be produced inorganically during oil formation in the `oil-kitchen'. Here we try to identify a magnetic proxy that can be used to trace hydrocarbon migration pathways by determining the morphology, abundance, mineralogy and size of the magnetic minerals present in reservoirs. We address this by examining the Tay formation in the Western Central Graben in the North Sea. The Tertiary sandstones are undeformed and laterally continuous in the form of an east-west trending channel, facilitating long distance updip migration of oil and gas to the west. We have collected 179 samples from 20 oil-stained wells and 15 samples from three dry wells from the British Geological Survey Core Repository. Samples were selected based on geological observations (water-wet sandstone, oil-stained sandstone, siltstones and shale). The magnetic properties of the samples were determined using room-temperature measurements on a Vibrating Sample Magnetometer (VSM), low-temperature (0-300K) measurements on a Magnetic Property Measurement System (MPMS) and high-temperature (300-973K) measurements on a Kappabridge susceptibility meter. We identified magnetite, pyrrhotite, pyrite and siderite in the samples. An increasing presence of ferrimagnetic iron sulphides is noticed along the known hydrocarbon migration pathway. Our initial results suggest mineralogy coupled with changes in grain size are possible proxies for hydrocarbon migration.

Degradation of volatile hydrocarbons from steam-classified solid waste by a mixture of aromatic hydrocarbon-degrading bacteria.

Science.gov (United States)

Leahy, Joseph G; Tracy, Karen D; Eley, Michael H

2003-03-01

Steam classification is a process for treatment of solid waste that allows recovery of volatile organic compounds from the waste via steam condensate and off-gases. A mixed culture of aromatic hydrocarbon-degrading bacteria was used to degrade the contaminants in the condensate, which contained approx. 60 hydrocarbons, of which 38 were degraded within 4 d. Many of the hydrocarbons, including styrene, 1,2,4-trimethylbenzene, naphthalene, ethylbenzene, m-/p-xylene, chloroform, 1,3-dichloropropene, were completely or nearly completely degraded within one day, while trichloroethylene and 1,2,3-trichloropropane were degraded more slowly.

Temporal Change of Seismic Earth's Inner Core Phases: Inner Core Differential Rotation Or Temporal Change of Inner Core Surface?

Science.gov (United States)

Yao, J.; Tian, D.; Sun, L.; Wen, L.

2017-12-01

the observed temporal changes of the inner core phases are caused by temporal changes of inner core surface. The temporal changes of inner core surface are found to occur in some localized regions within a short time scale (years to months), a phenomenon that should provide important clues to a potentially fundamental change of our understanding of core dynamics.

Recommendations for a first Core Outcome Measurement set for complex regional PAin syndrome Clinical sTudies (COMPACT)

Science.gov (United States)

Grieve, Sharon; Perez, Roberto SGM; Birklein, Frank; Brunner, Florian; Bruehl, Stephen; Harden R, Norman; Packham, Tara; Gobeil, Francois; Haigh, Richard; Holly, Janet; Terkelsen, Astrid; Davies, Lindsay; Lewis, Jennifer; Thomassen, Ilona; Connett, Robyn; Worth, Tina; Vatine, Jean-Jacques; McCabe, Candida S

2017-01-01

Complex Regional Pain Syndrome (CRPS) is a persistent pain condition that remains incompletely understood and challenging to treat. Historically, a wide range of different outcome measures have been used to capture the multidimensional nature of CRPS. This has been a significant limiting factor in the advancement of our understanding of the mechanisms and management of CRPS. In 2013, an international consortium of patients, clinicians, researchers and industry representatives was established, to develop and agree on a minimum core set of standardised outcome measures for use in future CRPS clinical research, including but not limited to clinical trials within adult populations The development of a core measurement set was informed through workshops and supplementary work, using an iterative consensus process. ‘What is the clinical presentation and course of CRPS, and what factors influence it?’ was agreed as the most pertinent research question that our standardised set of patient-reported outcome measures should be selected to answer. The domains encompassing the key concepts necessary to answer the research question were agreed as: pain, disease severity, participation and physical function, emotional and psychological function, self efficacy, catastrophizing and patient's global impression of change. The final core measurement set included the optimum generic or condition-specific patient-reported questionnaire outcome measures, which captured the essence of each domain, and one clinician reported outcome measure to capture the degree of severity of CRPS. The next step is to test the feasibility and acceptability of collecting outcome measure data using the core measurement set in the CRPS population internationally. PMID:28178071

Production of hydrocarbons, especially ethylene

Energy Technology Data Exchange (ETDEWEB)

1952-01-17

The invention has for its object a process for the production of gaseous nonsaturated hydrocarbons, particularly ethylene and aromatic hydrocarbons, by starting with hydrocarbon oils entirely of paraffinic nature or their fractions, which consists in putting the separated products in contact with solid inert material especially with porous nonmetallic inert material or of heavy metals or their alloys, maybe in a finely divided state or in the form, of pieces or chips, at a temperature above 500/sup 0/C, or better between 600 and 700/sup 0/C at a velocity per hour of 0.6 to 3.0, and preferably 0.75 to 1.5 parts per volume of products per each part of space volume of catalyst.

Process of distilling heavy hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

1929-12-03

This invention has for its object the distillation of heavy liquid hydrocarbons for the purpose of obtaining lighter hydrocarbons stable and immediately salable for fuels in combustion motors. The process is distinguished by the fact that the heavy hydrocarbon is distilled by means of heating to a temperature in keeping with the nature of the material to be treated up to 350/sup 0/C under pressure or without pressure the distillation being carried out on catalysts containing successively nickel, copper, and iron (3 parts of nickel, 1 part of copper, and 1 part of iron), the vapors produced by this distillation being exposed in turn to the action of catalysts of the same nature and in the same proportion.

Method for upgrading diene-containing hydrocarbon mixtures

Energy Technology Data Exchange (ETDEWEB)

Kidwell, L.E. Jr.; Holcomb, D.E.

1984-05-22

There is disclosed a method for upgrading of hydrocarbon mixtures, so as to reduce their content of gum precursors such as diolefins and pseudo-diolefins, and provide a resulting product mixture suitable for mild hydrogenation, for use as a motor fuel or as a feed stock to an extraction unit. The process comprises obtaining a hydrocarbon mixture containing about 60-90 wt. % of aromatic components, about 3-40 wt. % of dienes and pseudodienes, and monoolefins, and up to about 6 wt. % of relatively unreactive organic compounds, reacting this mixture with elemental sulfur in the approximate weight ratio of about 5-95 wt. % of the hydrocarbon mixture with about 95-5 wt. % of elemental sulfur, the reaction being carried out at a temperature in the range of 100/sup 0/-150/sup 0/ C. for about 10 minutes to 24 hours with good mixing, removing the unreacted materials by distillation and separating a sulfur-hydrocarbon reaction product to provide the upgraded hydrocarbon mixture.

Seawater-cultured Botryococcus braunii for efficient hydrocarbon extraction.

Directory of Open Access Journals (Sweden)

Kenichi Furuhashi

Full Text Available As a potential source of biofuel, the green colonial microalga Botryococcus braunii produces large amounts of hydrocarbons that are accumulated in the extracellular matrix. Generally, pretreatment such as drying or heating of wet algae is needed for sufficient recoveries of hydrocarbons from B. braunii using organic solvents. In this study, the Showa strain of B. braunii was cultured in media derived from the modified Chu13 medium by supplying artificial seawater, natural seawater, or NaCl. After a certain period of culture in the media with an osmotic pressure corresponding to 1/4-seawater, hydrocarbon recovery rates exceeding 90% were obtained by simply mixing intact wet algae with n-hexane without any pretreatments and the results using the present culture conditions indicate the potential for hydrocarbon milking.Seawater was used for efficient hydrocarbon extraction from Botryococcus braunii. The alga was cultured in media prepared with seawater or NaCl. Hydrocarbon recovery rate exceeding 90% was obtained without any pretreatment.

Effect of hydrocarbons on plasma treatment of NOx

Energy Technology Data Exchange (ETDEWEB)

Penetrante, B.M.; Pitz, W.J.; Hsaio, M.C.; Merritt, B.T.; Vogtlin, G.E. [Lawrence Livermore National Lab., CA (United States)

1997-12-31

Lean burn gasoline engine exhausts contain a significant amount of hydrocarbons in the form of propene. Diesel engine exhausts contain little gaseous hydrocarbon; however, they contain a significant amount of liquid-phase hydrocarbons (known as the volatile organic fraction) in the particulates. The objective of this paper is to examine the fate of NO{sub x} when an exhaust gas mixture that contains hydrocarbons is subjected to a plasma. The authors will show that the hydrocarbons promote the oxidation of NO to NO{sub 2}, but not the reduction of NO to N{sub 2}. The oxidation of NO to NO{sub 2} is strongly coupled with the hydrocarbon oxidation chemistry. This result suggests that gas-phase reactions in the plasma alone cannot lead to the chemical reduction of NO{sub x}. Any reduction of NO{sub x} to N{sub 2} can only be accomplished through heterogeneous reactions of NO{sub 2} with surfaces or particulates.

Reactor core performance estimating device

International Nuclear Information System (INIS)

Tanabe, Akira; Yamamoto, Toru; Shinpuku, Kimihiro; Chuzen, Takuji; Nishide, Fusayo.

1995-01-01

The present invention can autonomously simplify a neural net model thereby enabling to conveniently estimate various amounts which represents reactor core performances by a simple calculation in a short period of time. Namely, a reactor core performance estimation device comprises a nerve circuit net which divides the reactor core into a large number of spacial regions, and receives various physical amounts for each region as input signals for input nerve cells and outputs estimation values of each amount representing the reactor core performances as output signals of output nerve cells. In this case, the nerve circuit net (1) has a structure of extended multi-layered model having direct coupling from an upper stream layer to each of downstream layers, (2) has a forgetting constant q in a corrected equation for a joined load value ω using an inverse error propagation method, (3) learns various amounts representing reactor core performances determined using the physical models as teacher signals, (4) determines the joined load value ω decreased as '0' when it is to less than a predetermined value upon learning described above, and (5) eliminates elements of the nerve circuit net having all of the joined load value decreased to 0. As a result, the neural net model comprises an autonomously simplifying means. (I.S.)

Why cumulative impacts assessments of hydrocarbon activities in the Arctic fail to meet their purpose

DEFF Research Database (Denmark)

Kirkfeldt, Trine Skovgaard; Hansen, Anne Merrild; Olsen, Pernille

2017-01-01

The Arctic Region is characterised by vulnerable ecosystems and residing indigenous people, dependent on nature for fishing and hunting. The Arctic also contains a wealth of non-living natural resources such as minerals and hydrocarbons. Synergies between increased access and growing global deman...

Molecular characterization of autochthonous hydrocarbon utilizing ...

African Journals Online (AJOL)

Prof. Ogunji

Materials and Methods ... culturable hydrocarbon utilizing bacteria (HUB) were enumerated by vapour phase ... hydrocarbon utilizing bacterial isolates by boiling method according to ... obtained in this investigation are consistent with past field studies (Kostka et ... Microbial and other related changes in a Niger sediment.

Fort St. Vrain core performance

International Nuclear Information System (INIS)

McEachern, D.W.; Brown, J.R.; Heller, R.A.; Franek, W.J.

1977-07-01

The Fort St. Vrain High Temperature Gas Cooled Reactor core performance has been evaluated during the startup testing phase of the reactor operation. The reactor is graphite moderated, helium cooled, and uses coated particle fuel and on-line flow control to each of the 37 refueling regions. Principal objectives of startup testing were to determine: core and control system reactivity, radial power distribution, flow control capability, and initial fission product release. Information from the core demonstrates that Technical Specifications are being met, performance of the core and fuel is as expected, flow and reactivity control are predictable and simple for the operator to carry out

Volatilisation of aromatic hydrocarbons from soil

DEFF Research Database (Denmark)

Lindhardt, B.; Christensen, T.H.

1996-01-01

The non-steady-state fluxes of aromatic hydrocarbons were measured in the laboratory from the surface of soils contaminated with coal tar Four soil samples from a former gasworks site were used for the experiments. The fluxes were quantified for 11 selected compounds, 4 mono- and 7 polycyclic...... aromatic hydrocarbons, for a period of up to 8 or 16 days. The concentrations of the selected compounds in the soils were between 0.2 and 3,100 mu g/g. The study included the experimental determination of the distribution coefficient of the aromatic hydrocarbons between the sorbed phase and the water under...... saturated conditions. The determined distribution coefficients showed that the aromatic hydrocarbons were more strongly sorbed to the total organic carbon including the coal tar pitch - by a factor of 8 to 25 - than expected for natural organic matter. The fluxes were also estimated using an analytical...

Conceptual core designs for a 1200 MWe sodium cooled fast reactor

International Nuclear Information System (INIS)

Joo, H. K.; Lee, K. B.; Yoo, J. W.; Kim, Y. I.

2008-01-01

The conceptual core design for a 1200 MWe sodium cooled fast reactor is being developed under the framework of the Gen-IV SFR development program. To this end, three core concepts have been tested during the development of a core concept: a core with an enrichment split fuel, a core with a single-enrichment fuel with a region-wise varying clad thickness, and a core with a single-enrichment fuel with non-fuel rods. In order to optimize a conceptual core configuration which satisfies the design targets, a sensitivity study of the core design parameters has been performed. Two core concepts, the core with an enrichment-split fuel and the core with a single-enrichment fuel with a region-wise varying clad thickness, have been proposed as the candidates of the conceptual core for a 1200 MWe sodium cooled fast reactor. The detailed core neutronic, fuel behavior, thermal, and safety analyses will be performed for the proposed candidate core concepts to finalize the core design concept. (authors)

Recovery of hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

1941-02-10

A process is disclosed for recovery of hydrocarbon oils, especially lubricating oils or diesel oils, through pressure hydrogenation of distillation, extraction of hydrogenation products from coal or coaly materials or from oils such as mineral oils or tars in liquid phase by use in a reaction vessel of fixed-bed catalysts, characterized in that as starting material is employed material which has been freed of asphaltic and resinous material by hydrogenation refining, vacuum-steam distillation, treatment with hydrogen-rich hydrocarbons (hydroforming), or sulfuric acid.

Oils; lubricants; paraffin-wax compositions; hydrocarbon condensation products

Energy Technology Data Exchange (ETDEWEB)

1934-04-04

Petroleum hydrocarbons such as gasoline, kerosene, Diesel fuel oil, lubricating-oil, and paraffin wax, and like hydrocarbons such as are obtainable from shale oil and by the hydrogenation of carbonaceous materials, are improved by addition of products obtained by condensing a cyclic hydrocarbon with a saturated dihalogen derivative of an aliphatic hydrocarbon containing less than five carbon atoms. The addition of the condensation products increases the viscosity of the hydrocarbon oils specified, and is particularly useful in the case of lubricating-oils; addition of the condensation products to paraffin wax increases the transparency and adherent properties of the wax, and is useful in the manufacture of moulded articles such as candles; the products may also be used in solid lubricating-compositions.

Imaging fluid/solid interactions in hydrocarbon reservoir rocks.

Science.gov (United States)

Uwins, P J; Baker, J C; Mackinnon, I D

1993-08-01

The environmental scanning electron microscope (ESEM) has been used to image liquid hydrocarbons in sandstones and oil shales. Additionally, the fluid sensitivity of selected clay minerals in hydrocarbon reservoirs was assessed via three case studies: HCl acid sensitivity of authigenic chlorite in sandstone reservoirs, freshwater sensitivity of authigenic illite/smectite in sandstone reservoirs, and bleach sensitivity of a volcanic reservoir containing abundant secondary chlorite/corrensite. The results showed the suitability of using ESEM for imaging liquid hydrocarbon films in hydrocarbon reservoirs and the importance of simulating in situ fluid-rock interactions for hydrocarbon production programmes. In each case, results of the ESEM studies greatly enhanced prediction of reservoir/borehole reactions and, in some cases, contradicted conventional wisdom regarding the outcome of potential engineering solutions.

A method of refining aromatic hydrocarbons from coal chemical production

Energy Technology Data Exchange (ETDEWEB)

Zieborak, K.; Koprowski, A.; Ratajczak, W.

1979-10-01

A method is disclosed for refining aromatic hydrocarbons of coal chemical production by contact of liquid aromatic hydrocarbons and their mixtures with a strongly acid macroporous sulfocationite in the H-form at atmospheric pressure and high temperature. The method is distinguished in that the aromatic hydrocarbons and their mixtures, from which alkali compounds have already been removed, are supplied for refinement with the sulfocationite with simultaneous addition of olefin derivatives of aromatic hydrocarbons, followed by separation of pure hydrocarbons by rectification. Styrene or alpha-methylstyrene is used as the olefin derivatives of the aromatic hydrocarbons. The method is performed in several stages with addition of olefin derivatives of aromatic hydrocarbons at each stage.

Process for recovery of liquid hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Millar, J.F.; Cockshott, J.E.

1978-04-11

Methane is recovered as a gas for discharge to a pipeline from a gas stream containing methane and heavier hydrocarbons, principally ethane and propane. Separation is accomplished by condensing the heavier hydrocarbons and distilling the methane therefrom. A liquid product (LPG) comprising the heavier hydrocarbons is subsequently recovered and transferred to storage. Prior to being discharged to a pipeline, the recovered methane gas is compressed and in undergoing compression the gas is heated. The heat content of the gas is employed to reboil the refrigerant in an absorption refrigeration unit. The refrigeration unit is used to cool the LPG prior to its storage.

Worldwide overview of hydrocarbons and perspectives

International Nuclear Information System (INIS)

Tonnac, Alain de; Perves, Jean-Pierre

2013-12-01

This publication presents and comments data regarding the share of hydrocarbons in the world energy consumption, hydrocarbon trade flows, the new situation created by the emergence of shale hydrocarbons and the consequences for the world economy, and possible risks. The authors first comment the evolution of energy consumption and outline that the objectives of CO 2 and greenhouse gas emission will not be reached (these emissions increased in 2012 and in 2013). They indicate the emission situation in the USA and Japan, and notice that the objectives defined by the IEA are quite different from those defined by the EU. They analyse the evolutions by distinguishing different periods: 2005-2008 as a reference period, 2008-2012 as a period of change, and the current period as a period of flow inversion. Then, the authors propose two different scenarios of evolution of economic and energy policies. The evolution of hydrocarbon demand is commented, and the levels of reserves (oil, conventional gas, coal, nuclear fuels) are discussed. The market evolution is also discussed, not only from an economic point of view, but also in relationship with geopolitics. The authors notably outline that the energy price is different from one country to the other, discuss the issue of hydrocarbon refining, the role of CO 2 tax

Study of hydrocarbons in bottom sediments of the northern Dvina River-White Sea geochemical barrier during spring flood. Volume 2

International Nuclear Information System (INIS)

Nemirovskaya, I.; Shevchenko, V.

2007-01-01

The Northern Dvina in Northern Russia is the main river of the White Sea reservoir. The water discharge is 108 km 3 per year. With active shipping and several large pulp and paper mills that operate in the region, the river is a supplier of polluting substances. Weathered oil and pyrogenic compounds dominate the composition of hydrocarbons. During flooding, the Northern Dvina - Dvina Bay geochemical barrier becomes a filter, which prevents pollutants from penetrating to the White Sea. This paper summarized data on the concentration and composition of hydrocarbons, aliphatic hydrocarbons (AHC) and polycyclic aromatic hydrocarbons (PAH) in the marine water and bottom sediments at the mouth of the Northern Dvina/White Sea. Nearly similar concentrations of organic compounds were found in the Northern Dvina River water and in the near-mouth White Sea water area. However, their distribution conforms to the marginal filter rules. Natural terrigenous hydrocarbon compounds were found to dominate in all forms. Biogenic autochthonous hydrocarbons were detected in the near-shore areas and in the outer zone of the marginal filter of the Northern Dvina River, where PAH are formed together with AHC. 20 refs., 2 tabs., 4 figs

Hydrocarbon-degradation by Isolate Pseudomonas lundensis UTAR FPE2

Directory of Open Access Journals (Sweden)

Adeline, S. Y. Ting

2009-01-01

Full Text Available In this study, the potential of isolate Pseudomonas lundensis UTAR FPE2 as a hydrocarbon degrader was established. Their biodegradation activity was first detected with the formation of clearing zones on Bushnell-Hass agar plates, with the largest diameter observed on plates supplemented with paraffin, followed by mineral oil and petrol. Utilization of hydrocarbon sources were again detected in broth cultures supplemented with similar hydrocarbon substrates, where the mean viable cell count recovered from hydrocarbon-supplemented broth cultures were higher than the initial inoculum except for napthalene. In both tests, the isolate showed higher degradability towards aliphatic hydrocarbon sources, and the least activity towards the aromatic hydrocarbon naphthalene. The isolate P. lundensis UTAR FPE2 (8 log10 cfu/mL also degraded crude diesel sample, with 69% degradation during the first three days. To conclude, this study suggests the potential use of this isolate for bioremediation of hydrocarbon-contaminated environments.

Bioassay of polycyclic aromatic hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Van Kirk, E.A.

1980-08-01

A positive relationship was found between the photodynamic activity of 24 polycyclic aromatic hydrocarbons versus published results on the mutagenicity, carcinogenicity, and initiation of unscheduled DNA synthesis. Metabolic activation of benzo(a)pyrene resulted in detection of increased mutagenesis in Paramecium tetraurelia as found also in the Ames Salmonella assay. The utility of P. tetraurelia as a biological detector of hazardous polycyclic aromatic hydrocarbons is discussed.

Modelling the regional climate and isotopic composition of Svalbard precipitation using REMOiso: a comparison with available GNIP and ice core data

NARCIS (Netherlands)

Divine, D.V.; Sjolte, J.; Isaksson, E.; Meijer, H.A.J.; van de Wal, R.S.W.; Martma, T.; Pohjola, V.; Sturm, C.; Godtliebsen, F.

2011-01-01

Simulations of a regional (approx. 50 km resolution) circulation model REMOiso with embedded stable water isotope module covering the period 1958-2001 are compared with the two instrumental climate and four isotope series (δ18O) from western Svalbard. We examine the data from ice cores drilled on

Modelling the regional climate and isotopic composition of Svalbard precipitation using REMOiso : a comparison with available GNIP and ice core data

NARCIS (Netherlands)

Divine, D. V.; Sjolte, J.; Isaksson, E.; Meijer, H. A. J.; van de Wal, R. S. W.; Martma, T.; Pohjola, V.; Sturm, C.; Godtliebsen, F.

2011-01-01

Simulations of a regional (approx. 50 km resolution) circulation model REMOiso with embedded stable water isotope module covering the period 1958-2001 are compared with the two instrumental climate and four isotope series (d18O) from western Svalbard. We examine the data from ice cores drilled on

Potential hydrocarbon producing species of Western Ghats, Tamil Nadu, India

Energy Technology Data Exchange (ETDEWEB)

Augustus, G.D.P.S.; Jayabalan, M.; Rajarathinam, K. [Research Centre in Bombay, V.H.N.S.N. College, Virudhunagar (India); Ray, A.K. [Sardar Patel Univ., Anand (India). Dept. of Chemistry; Seiler, G.J. [USDA, ARS, Northern Crop Science Lab., Fargo, ND (United States)

2002-09-01

The decline in the world supplies of hydrocarbons has led to the search for alternate sources of fuel and chemicals. Plant species are potential sources of hydrocarbons. Large-scale screening of plants growing in the Western Ghats, Tamil Nadu, India was conducted to assess the hydrocarbon production and the type of isoprene compound(s) present. Three species contained more than 3% hydrocarbon. Sarcostemma brevistigma had the highest concentration of hydrocarbon with 3.6%. Seven species contained more than 2% of hydrocarbons among the plant species screened. The hydrocarbon fraction of Ficus elastica (leaf) had a gross heat value of 9834 cal/g (41.17 MJ/kg), which is close to the caloric value of fuel oil. Six hydrocarbon fractions contained gross heat values of more than 9000 cal/g (37.68 MJ/kg). Of the 13 species hydrocarbon fraction analysed, seven species contained cis-polyisoprene compounds, while two species contained trans-polyisoprenes. Cis and trans polyisoprenes are potential alternative energy sources for fuel and/or as industrial raw materials. (author)

Core burn-up calculation method of JRR-3

International Nuclear Information System (INIS)

Kato, Tomoaki; Yamashita, Kiyonobu

2007-01-01

SRAC code system is utilized for core burn-up calculation of JRR-3. SRAC code system includes calculation modules such as PIJ, PIJBURN, ANISN and CITATION for making effective cross section and calculation modules such as COREBN and HIST for core burn-up calculation. As for calculation method for JRR-3, PIJBURN (Cell burn-up calculation module) is used for making effective cross section of fuel region at each burn-up step. PIJ, ANISN and CITATION are used for making effective cross section of non-fuel region. COREBN and HIST is used for core burn-up calculation and fuel management. This paper presents details of NRR-3 core burn-up calculation. FNCA Participating countries are expected to carry out core burn-up calculation of domestic research reactor by SRAC code system by utilizing the information of this paper. (author)

The carbon isotope biogeochemistry of the individual hydrocarbons in bat guano and the ecology of the insectivorous bats in the region of Carlsbad, New Mexico

International Nuclear Information System (INIS)

Des Marais, D.J.; Mitchell, J.M.; Meinschein, W.G.; Hayes, J.M.

1980-01-01

The structures and 13 C contents of individual alkanes extracted from bat guano found in the Carlsbad region of New Mexico can be related to both the photosynthetic pathways of the local plants and the feeding habits of the insects that support the bats. Carbon isotopic analyses show that equivalent numbers of C 3 and C 4 native plant species occupy the Pecos River Valley, a very significant feeding area for the Carlsbad bats. During the seasons when bats frequent the area, the agricultural crops consist principally of alfalfa and cotton, both C 3 plants. The molecular composition of the bat guano hydrocarbons is fully consistent with an insect origin. Two isotopically distinct groups of insect branched alkanes were discerned. These two groups of alkanes derived from two chemotaxonomically distinct populations of insects possessing distinctly different feeding habits. It is possible that one population grazes predominantly on crops whereas the other population prefers native vegetation. This and other isotopic evidence suggests that crop pests constitute a major percentage of the bats' diet. Because the guano sample was less than 40 years old, this material reflects the present day plant community in the Pecos River Valley. Future studies of more ancient guano deposits should reveal a measurable influence of both natural and man-induced vegetative changes with time upon the 13 C content of the bat guano hydrocarbons. (author)

AD1995: NW Europe's hydrocarbon industry

International Nuclear Information System (INIS)

Glennie, K.; Hurst, A.

1996-01-01

This volume concerns itself with wide-ranging aspects of the upstream hydro-carbon industry over the whole of NW Europe. As such, the book contrasts with many thematic volumes by presenting a broad range of topics side-by-side. One section of the book looks back at the history of geological exploration and production, and provides an overview of hydrocarbon exploration across NW Europe. Another section covers the state of the art in hydrocarbon exploration and production. This includes an update on computer-based basin modelling overpressure systems, innovations in reservoir engineering and reserve estimation, 3D seismic and the geochemical aspects of secondary migration. The final section of the book takes a look into the future. This covers the remaining hydrocarbon resources of the North Sea, managing risk in oil field development, oil field economics, and pollution and the environment. It is the editors' hope that several key areas of NW Europe's upstream oil industry have been usefully summarized in the volume. (Author)

Enrichment of light hydrocarbon mixture

Science.gov (United States)

Yang,; Dali, [Los Alamos, NM; Devlin, David [Santa Fe, NM; Barbero, Robert S [Santa Cruz, NM; Carrera, Martin E [Naperville, IL; Colling, Craig W [Warrenville, IL

2010-08-10

Light hydrocarbon enrichment is accomplished using a vertically oriented distillation column having a plurality of vertically oriented, nonselective micro/mesoporous hollow fibers. Vapor having, for example, both propylene and propane is sent upward through the distillation column in between the hollow fibers. Vapor exits neat the top of the column and is condensed to form a liquid phase that is directed back downward through the lumen of the hollow fibers. As vapor continues to ascend and liquid continues to countercurrently descend, the liquid at the bottom of the column becomes enriched in a higher boiling point, light hydrocarbon (propane, for example) and the vapor at the top becomes enriched in a lower boiling point light hydrocarbon (propylene, for example). The hollow fiber becomes wetted with liquid during the process.

Purifying hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Dunstan, A E

1918-06-03

Ligroin, kerosene, and other distillates from petroleum and shale oil, are purified by treatment with a solution of a hypochlorite containing an excess of alkali. The hydrocarbon may be poured into brine, the mixture stirred, and an electric current passed through. Heat may be applied.

Nitrogen fixation in arctic marine sediments: effect of oil and hydrocarbon fractions

Energy Technology Data Exchange (ETDEWEB)

Knowles, R; Wishart, C

1977-06-01

Nitrogen fixation (acetylene reduction) was measured in grab and core samples of sediments from the Beaufort Sea and Eskimo Lakes, Northwest Territories, Canada. Very low rates (about 25 mg N/m/sup 2/.year) were detected in untreated sediments. Activity was markedly stimulated by the addition of glucose, sucrose, lactose, mannitol and malate but much less so by acetate; negligible activity was supported by N-acetylglucosamine. There was no consistent effect of the presence or absence of oxygen. Nitrogen fixation potentials in glucose-supplemented sediment samples showed large variation between stations, between samples from the same station and between depths within single cores down to 18 cm. Weathered Normal Wells crude oil, hexane, decane, dodecane and hexadecane had no effect, stimulatory or inhibitory, on nitrogen fixation or carbon dioxide evolution. 1,2,4-trimethylbenzene caused complete inhibition of nitrogen fixation but only partial inhibition of CO/sub 2/ evolution. There was no evidence of utilization of any of the hydrocarbons tested during periods of over 30 days under the experimental conditions employed.

Culture-dependent characterization of hydrocarbon utilizing bacteria ...

African Journals Online (AJOL)

EARNEST

Hydrocarbons interact with the environment and micro- organisms determining the .... it is pertinent to study the community dynamics of hydrocarbon degrading bacteria ... Chikere CB (2013). Application of molecular microbiology techniques in.

Identifying future directions for subsurface hydrocarbon migration research

Science.gov (United States)

Leifer, I.; Clark, J. F.; Luyendyk, B.; Valentine, D.

Subsurface hydrocarbon migration is important for understanding the input and impacts of natural hydrocarbon seepage on the environment. Great uncertainties remain in most aspects of hydrocarbon migration, including some basic mechanisms of this four-phase flow of tar, oil, water, and gas through the complex fracture-network geometry particularly since the phases span a wide range of properties. Academic, government, and industry representatives recently attended a workshop to identify the areas of greatest need for future research in shallow hydrocarbon migration.Novel approaches such as studying temporal and spatial seepage variations and analogous geofluid systems (e.g., geysers and trickle beds) allow deductions of subsurface processes and structures that remain largely unclear. Unique complexities exist in hydrocarbon migration due to its multiphase flow and complex geometry, including in-situ biological weathering. Furthermore, many aspects of the role of hydrocarbons (positive and negative) in the environment are poorly understood, including how they enter the food chain (respiration, consumption, etc.) and “percolate” to higher trophic levels. But understanding these ecological impacts requires knowledge of the emissions' temporal and spatial variability and trajectories.

33 CFR 157.166 - Hydrocarbon emissions.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Hydrocarbon emissions. 157.166 Section 157.166 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.166 Hydrocarbon emissions. If the...

Impairment of interferon regulatory factor-3 activation by hepatitis C virus core protein basic amino acid region 1.

Science.gov (United States)

Inoue, Kazuaki; Tsukiyama-Kohara, Kyoko; Matsuda, Chiho; Yoneyama, Mitsutoshi; Fujita, Takashi; Kuge, Shusuke; Yoshiba, Makoto; Kohara, Michinori

2012-11-30

Interferon regulatory factor-3 (IRF-3), a key transcriptional factor in the type I interferon system, is frequently impaired by hepatitis C virus (HCV), in order to establish persistent infection. However, the exact mechanism by which the virus establishes persistent infection has not been fully understood yet. The present study aimed to investigate the effects of various HCV proteins on IRF-3 activation, and elucidate the underlying mechanisms. To achieve this, full-length HCV and HCV subgenomic constructs corresponding to structural and each of the nonstructural proteins were transiently transfected into HepG2 cells. IFN-β induction, plaque formation, and IRF-3 dimerization were elicited by Newcastle disease virus (NDV) infection. The expressions of IRF-3 homodimer and its monomer, Ser386-phosphorylated IRF-3, and HCV core protein were detected by immunofluorescence and western blotting. IFN-β mRNA expression was quantified by real-time PCR (RT-PCR), and IRF-3 activity was measured by the levels of IRF-3 dimerization and phosphorylation, induced by NDV infection or polyriboinosinic:polyribocytidylic acid [poly(I:C)]. Switching of the expression of the complete HCV genome as well as the core proteins, E1, E2, and NS2, suppressed IFN-β mRNA levels and IRF-3 dimerization, induced by NDV infection. Our study revealed a crucial region of the HCV core protein, basic amino acid region 1 (BR1), to inhibit IRF-3 dimerization as well as its phosphorylation induced by NDV infection and poly (I:C), thus interfering with IRF-3 activation. Therefore, our study suggests that rescue of the IRF-3 pathway impairment may be an effective treatment for HCV infection. Copyright © 2012 Elsevier Inc. All rights reserved.

Analysis and Tendencies of Metals and POPs in a Sediment Core from the Alvarado Lagoon System (ALS), Veracruz, Mexico.

Science.gov (United States)

Botello, A V; Villanueva, F S; Rivera, R F; Velandia, A L; de la Lanza, G E

2018-03-06

This study focused on dating of a sediment core from the Alvarado Lagoon System, Veracruz, Mexico, calculating the sedimentation rate by using 210 Pb to determine the tendency towards pollution by polycyclic aromatic hydrocarbons, organochlorides, the metals Cd, Cr, Cu, Hg, Ni, Pb, and V, and organic matter content. The activity of total Pb and supported Pb in the samples was 83.1 and 29.5 Bq kg -1 , respectively, whereas the average estimated sedimentation rate was 0.48 ± 0.09 cm per year -1 . The organic matter values exhibited linear behavior throughout the historical profile, with values under 2.5%. Metal concentrations followed the order V > Cr > Ni > Cu > Pb > Hg > Cd. Variations found in Cr, Ni, Pb, and V concentrations are basically due to three meteorological phenomena that hit the region: hurricanes Gladys, Hilda, and Janet in September of 1955. V, Ni, and Hg input comes from anthropogenic and lithogenic sources. The presence of individual polycyclic aromatic hydrocarbons showed no ascending accumulation pattern over time, nor did it show any significant statistical correlation to OM. As for the organochlorine pesticides, 63.61% of the total sum of these compounds were from the ciclodienics family. Concentration of p,p'-DDT was observed only in the earliest profile, from 1929.

Hydrocarbon removal with constructed wetlands

OpenAIRE

Eke, Paul Emeka

2008-01-01

Wetlands have long played a significant role as natural purification systems, and have been effectively used to treat domestic, agricultural and industrial wastewater. However, very little is known about the biochemical processes involved, and the use of constructed treatment wetlands in the removal of petroleum aromatic hydrocarbons from produced and/or processed water. Wastewaters from the oil industry contain aromatic hydrocarbons such as benzene, toluene, ethylbenzene and x...

Mid-IR Absorption Cross-Section Measurements of Hydrocarbons

KAUST Repository

Alrefae, Majed Abdullah

2013-05-01

Laser diagnostics are fast-response, non-intrusive and species-specific tools perfectly applicable for studying combustion processes. Quantitative measurements of species concentration and temperature require spectroscopic data to be well-known at combustion-relevant conditions. Absorption cross-section is an important spectroscopic quantity and has direct relation to the species concentration. In this work, the absorption cross-sections of basic hydrocarbons are measured using Fourier Transform Infrared (FTIR) spectrometer, tunable Difference Frequency Generation laser and fixed wavelength helium-neon laser. The studied species are methane, methanol, acetylene, ethylene, ethane, ethanol, propylene, propane, 1-butene, n-butane, n-pentane, n-hexane, and n-heptane. The Fourier Transform Infrared (FTIR) spectrometer is used for the measurements of the absorption cross-sections and the integrated band intensities of the 13 hydrocarbons. The spectral region of the spectra is 2800 – 3400 cm-1 (2.9 – 3.6 μm) and the temperature range is 673 – 1100 K. These valuable data provide huge opportunities to select interference-free wavelengths for measuring time-histories of a specific species in a shock tube or other combustion systems. Such measurements can allow developing/improving chemical kinetics mechanisms by experimentally determining reaction rates. The Difference Frequency Generation (DFG) laser is a narrow line-width, tunable laser in the 3.35 – 3.53 μm wavelength region which contains strong absorption features for most hydrocarbons due to the fundamental C-H vibrating stretch. The absorption cross-sections of propylene are measured at seven different wavelengths using the DFG laser. The temperature range is 296 – 460 K which is reached using a Reflex Cell. The DFG laser is very attractive for kinetic studies in the shock tube because of its fast time response and the potential possibility of making species-specific measurements. The Fixed wavelength

Soft magnetic characteristics of laminated magnetic block cores assembled with a high Bs nanocrystalline alloy

Directory of Open Access Journals (Sweden)

Atsushi Yao

2018-05-01

Full Text Available This paper focuses on an evaluation of core losses in laminated magnetic block cores assembled with a high Bs nanocrystalline alloy in high magnetic flux density region. To discuss the soft magnetic properties of the high Bs block cores, the comparison with amorphous (SA1 block cores is also performed. In the high Bs block core, both low core losses and high saturation flux densities Bs are satisfied in the low frequency region. Furthermore, in the laminated block core made of the high Bs alloy, the rate of increase of iron losses as a function of the magnetic flux density remains small up to around 1.6 T, which cannot be realized in conventional laminated block cores based on amorphous alloy. The block core made of the high Bs alloy exhibits comparable core loss with that of amorphous alloy core in the high-frequency region. Thus, it is expected that this laminated high Bs block core can achieve low core losses and high saturation flux densities in the high-frequency region.

Crystallite-conjugation regions in polycrystalline transition and noble metals. 1. Composition and properties of point defects in the cores of crystallite-conjugation regions in polycrystalline Cr, Ta and W

International Nuclear Information System (INIS)

Klotsman, S.M.; Kajgorodov, V.N.; Ermakov, A.V.; Rudenko, V.K.

2004-01-01

With the use of available results of theoretical investigations on structure and properties of crystallite conjugation regions (CCR) the types and relaxation volumes of point defects arising in a core of the CCR of polycrystalline Ta, W and Cr after vacuum annealing (10 -6 - 10 -5 torr) are determined. Temperature dependences are studied for isomer shifts δ 1 and δ 2 of -1 and -2 components of emission spectra of NGR-irradiation 57 Co( 57 Fe) atomic probes localized in a core of the CCR and in adjacent zones of the lattice of polycrystalline solid solutions of O(Ta), O(W) and O(Cr). A comparison of the dependences obtained is carried and the specific features observed are explained for O(Cr) [ru

Performance estimation of ejector cycles using heavier hydrocarbon refrigerants

International Nuclear Information System (INIS)

Kasperski, Jacek; Gil, Bartosz

2014-01-01

Computer software basing on theoretical model of Huang et al. with thermodynamic properties of hydrocarbons was prepared. Investigation was focused on nine hydrocarbons: propane, butane, iso-butane, pentane, iso-pentane, hexane, heptane and octane. A series of calculations was carried out for the generator temperature between 70 and 200 °C, with assumed temperatures of evaporation 10 °C and condensation 40 °C. Calculation results show that none of the hydrocarbons enables high efficiency of a cycle in a wide range of temperature. Each hydrocarbon has its own maximal entrainment ratio at its individual temperature of optimum. Temperatures of entrainment ratios optimum increase according to the hydrocarbon heaviness with simultaneous increase of entrainment ratio peak values. Peak values of the COP do not increase according to the hydrocarbons heaviness. The highest COP = 0.32 is achieved for iso-butane at 102 °C and the COP = 0.28 for pentane at 165 °C. Heptane and octane can be ignored. - Highlights: • Advantages of use of higher hydrocarbons as ejector refrigerants were presumed. • Computer software basing on theoretical model of Huang et al. (1999) was prepared. • Optimal temperature range of vapor generation for each hydrocarbon was calculated

Introducing FACETS, the Framework Application for Core-Edge Transport Simulations

International Nuclear Information System (INIS)

Cary, John R.; Candy, Jeff; Cohen, Ronald H.; Krasheninnikov, Sergei I.; McCune, Douglas C.; Estep, Donald J.; Larson, Jay W.; Malony, Allen; Worley, Patrick H.; Carlsson, Johann Anders; Hakim, A.H.; Hamill, P.; Kruger, Scott E.; Muzsala, S.; Pletzer, Alexander; Shasharina, Svetlana; Wade-Stein, D.; Wang, N.; McInnes, Lois C.; Wildey, T.; Casper, T.A.; Diachin, Lori A.; Epperly, Thomas; Rognlien, T.D.; Fahey, Mark R.; Kuehn, Jeffery A.; Morris, A.; Shende, Sameer; Feibush, E.; Hammett, Gregory W.; Indireshkumar, K.; Ludescher, C.; Randerson, L.; Stotler, D.; Pigarov, A.; Bonoli, P.; Chang, C.S.; D'Ippolito, D.A.; Colella, Philip; Keyes, David E.; Bramley, R.

2007-01-01

The FACETS (Framework Application for Core-Edge Transport Simulations) project began in January 2007 with the goal of providing core to wall transport modeling of a tokamak fusion reactor. This involves coupling previously separate computations for the core, edge, and wall regions. Such a coupling is primarily through connection regions of lower dimensionality. The project has started developing a component-based coupling framework to bring together models for each of these regions. In the first year, the core model will be a 1 dimensional model (1D transport across flux surfaces coupled to a 2D equilibrium) with fixed equilibrium. The initial edge model will be the fluid model, UEDGE, but inclusion of kinetic models is planned for the out years. The project also has an embedded Scientific Application Partnership that is examining embedding a full-scale turbulence model for obtaining the crosssurface fluxes into a core transport code.

Neutronic characteristics of FLWR in the transition phase changing from high conversion core to breeder core

International Nuclear Information System (INIS)

Akie, Hiroshi; Nakano, Yoshihiro; Okubo, Tsutomu

2009-01-01

Innovative Water Reactor for Flexible Fuel Cycle (FLWR) is a low moderation type boiling water reactor which can realize plutonium multiple recycling and breeding. For the introduction stage of FLWR, a high conversion (HC) type FLWR is proposed to keep technical continuity from current light water reactors. The HC core of FLWR has a less tight fuel lattice with lower coolant void fraction than the breeder (BR) type core. The HC type FLWR core is to be shifted to the BR core by only replacing the fuel assemblies of the same outer shape and size in the same reactor system. In the HC to BR transition phase of FLWR, there exist both types of fuel assemblies in the same core configuration. In the HC assembly, neutron spectrum is softer than in the BR assembly, and the axial fuel and blanket arrangement is different from the BR assembly. Due to these differences, there might appear a power peaking in the adjacent region between HC and BR assemblies. The power distribution in the HC + BR assemblies mixed core configuration is studied by performing assembly calculations and core calculations on a few assemblies local geometry and the whole core geometry. As a result, although a power peaking can be locally very large in the HC and BR assemblies adjacent regions, such local power peakings are shown to be effectively reduced by considering a rod-wise fuel enrichment distribution. In the whole core calculation, it seems possible to optimize the fuel assembly loading and shuffling pattern to avoid large power level mismatch between the assemblies. It is expected that FLWR can be shifted from HC type to BR type without major neutronic difficulties. (author)

Hydrocarbon studies in Puget Sound and off the Washington coast. Progress report, March 1977--February 1978

International Nuclear Information System (INIS)

Carpenter, R.; Fairhall, A.W.

1978-01-01

This report summarizes progress in the first 2.5 yrs of our studies of the amounts, types, and probable origins of aliphatic, aromatic, S-, and N-containing hydrocarbons in sediments, organisms, and waters of Puget Sound and the Washington coast. We are trying to identify the relative importances of the various possible sources of these substances, the major pathways by which they are transferred through some parts of the marine food web, their rates of transfer, and their ultimate fates. We have found that changes in aliphatic and aromatic hydrocarbon compositions are evident in 210 Pb dated sediment cores from central Puget Sound. These changes are due both to natural diagenetic processes and to low level inputs of fossil fuels from a variety of sources. We have found measurable amounts of both S- and N-containing compounds in these Puget Sound sediments. We believe the first results of our studies of the role of zooplankton fecal pellets in the cycling of trace chemicals in the sea have shown that fecal pellets are an important vertical transport agent for hydrocarbons in the sea. We now have defined the natural variations in 14 C and 13 C/ 12 C isotope ratios of the inorganic carbon in Puget Sound seawater. Carbon isotope abundances for organisms and sediments are also reported for selected sites

Polycyclic’ Aromatic Hydrocarbon Induced Intracellular Signaling and Lymphocyte Apoptosis

DEFF Research Database (Denmark)

Schneider, Alexander M.

The aryl hydrocarbon (dioxin) receptor (AhR) is a transcription factor possessing high affinity to potent environmental pollutants, polycyclic aromatic hydrocarbons (PAH) and related halogenated hydrocarbons (e.g. dioxins). Numerous research attribute toxicity of these compounds to the receptor...

Assessment and source identification of pollution risk for touristic ports: Heavy metals and polycyclic aromatic hydrocarbons in sediments of 4 marinas of the Apulia region (Italy).

Science.gov (United States)

Mali, Matilda; Dell'Anna, Maria Michela; Mastrorilli, Piero; Damiani, Leonardo; Piccinni, Alberto Ferruccio

2017-01-30

The Apulia region in Italy has the longest Adriatic coastline; thus, maritime tourism is the driving force for its economic development. Pollution risk for four representative touristic ports of the region was assessed by determining the concentrations of 10 metals, 16 polycyclic aromatic hydrocarbons (PAHs) congeners, and the main nutrients. The cumulative mean Effects Range-Median quotient (mERMq) was used to assess the hazard degree, while the distribution patterns and content ratios of different PAH sediment concentrations were investigated to identify the pollution sources. Principal component analyses indicated an anomalous pollution trend for one of the small touristic ports assessed; this trend emerged from contamination by heavy metals and PAHs to a larger extent than expected, considering the main activity in this port, especially in its inner basin. The reason of this anomaly is thought to be the hydrodynamic and/or other stress factors. Copyright © 2016 Elsevier Ltd. All rights reserved.

Method for production of unsaturated gaseous hydrocarbons, particularly ethylene, and of aromatic hydrocarbons, adapted as motor fuels

Energy Technology Data Exchange (ETDEWEB)

1952-10-24

A method is described for the production of unsaturated gaseous hydrocarbons, in particular of ethylene, and of aromatic hydrocarbons from hydrocarbon oils or from fractions of the same, characterized by the fact that the raw materials are brought into contact with porous, inert substances in the form of fine distribution or of pieces at a temperature of above 500 and in particular from 600 to about 700/sup 0/C and with a traversing speed of from 0.3 up to about 3.0 volumetric parts, preferably up to 1.5 volumetric parts of raw material per volumetric part of the chamber and per hour.

Seasonal Variations in Health Hazards from Polycyclic Aromatic Hydrocarbons Bound to Submicrometer Particles at Three Characteristic Sites in the Heavily Polluted Polish Region

Directory of Open Access Journals (Sweden)

Barbara Kozielska

2014-12-01

Full Text Available Suspended particles with aerodynamic diameters not greater than 1 μm (PM1 were sampled at the urban background; regional background; and urban traffic points in southern Poland. In total, 120 samples were collected between 2 August 2009 and 27 December 2010. Sixteen polycyclic aromatic hydrocarbons (PAHs were determined in each sample. The samples were collected with a high volume sampler (Digitel. Afterwards, they were chemically analyzed with a gas chromatograph equipped with a flame ionization detector (Perkin Elmer Clarus 500. The mean concentration values of the PAH sum (ΣPAH and particular PAHs; the percentages of carcinogenic PAHs in total PAHs (ΣPAHcarc/ΣPAH; carcinogenic equivalent (CEQ; mutagenic equivalent (MEQ; and TCDD-toxic equivalent (TEQ were much higher in the winter (heating season than in the summer (non-heating one. For both periods, the resulting average values obtained were significantly higher (a few; and sometimes a several dozen times higher in the researched Polish region than the values observed in other areas of the world. Such results indicate the importance of health hazards resulting from PM1 and PM1-bound PAHs in this Polish area.

Catalytic conversion of alcohols to hydrocarbons with low benzene content

Energy Technology Data Exchange (ETDEWEB)

Narula, Chaitanya K.; Davison, Brian H.; Keller, Martin

2016-03-08

A method for converting an alcohol to a hydrocarbon fraction having a lowered benzene content, the method comprising: converting said alcohol to a hydrocarbon fraction by contacting said alcohol, under conditions suitable for converting said alcohol to said hydrocarbon fraction, with a metal-loaded zeolite catalyst catalytically active for converting said alcohol to said hydrocarbon fraction, and contacting said hydrocarbon fraction with a benzene alkylation catalyst, under conditions suitable for alkylating benzene, to form alkylated benzene product in said hydrocarbon fraction. Also described is a catalyst composition useful in the method, comprising a mixture of (i) a metal-loaded zeolite catalyst catalytically active for converting said alcohol to said hydrocarbon, and (ii) a benzene alkylation catalyst, in which (i) and (ii) may be in a mixed or separated state. A reactor for housing the catalyst and conducting the reaction is also described.

Catalytic conversion of alcohols to hydrocarbons with low benzene content

Energy Technology Data Exchange (ETDEWEB)

Narula, Chaitanya K.; Davison, Brian H.; Keller, Martin

2016-09-06

A method for converting an alcohol to a hydrocarbon fraction having a lowered benzene content, the method comprising: converting said alcohol to a hydrocarbon fraction by contacting said alcohol, under conditions suitable for converting said alcohol to said hydrocarbon fraction, with a metal-loaded zeolite catalyst catalytically active for converting said alcohol to said hydrocarbon fraction, and contacting said hydrocarbon fraction with a benzene alkylation catalyst, under conditions suitable for alkylating benzene, to form alkylated benzene product in said hydrocarbon fraction. Also described is a catalyst composition useful in the method, comprising a mixture of (i) a metal-loaded zeolite catalyst catalytically active for converting said alcohol to said hydrocarbon, and (ii) a benzene alkylation catalyst, in which (i) and (ii) may be in a mixed or separated state. A reactor for housing the catalyst and conducting the reaction is also described.

Methods for reformation of gaseous hydrocarbons using electrical discharge

KAUST Repository

Cha, Min Suk

2017-02-16

Methods for the reformation of gaseous hydrocarbons are provided. The methods can include forming a bubble containing the gaseous hydrocarbon in a liquid. The bubble can be generated to pass in a gap between a pair of electrodes, whereby an electrical discharge is generated in the bubble at the gap between the electrodes. The electrodes can be a metal or metal alloy with a high melting point so they can sustain high voltages of up to about 200 kilovolts. The gaseous hydrocarbon can be combined with an additive gas such as molecular oxygen or carbon dioxide. The reformation of the gaseous hydrocarbon can produce mixtures containing one or more of H2, CO, H2O, CO2, and a lower hydrocarbon such as ethane or ethylene. The reformation of the gaseous hydrocarbon can produce low amounts of CO2 and H2O, e.g. about 15 mol-% or less.

Methods for reformation of gaseous hydrocarbons using electrical discharge

KAUST Repository

Cha, Min; Zhang, Xuming

2017-01-01

Methods for the reformation of gaseous hydrocarbons are provided. The methods can include forming a bubble containing the gaseous hydrocarbon in a liquid. The bubble can be generated to pass in a gap between a pair of electrodes, whereby an electrical discharge is generated in the bubble at the gap between the electrodes. The electrodes can be a metal or metal alloy with a high melting point so they can sustain high voltages of up to about 200 kilovolts. The gaseous hydrocarbon can be combined with an additive gas such as molecular oxygen or carbon dioxide. The reformation of the gaseous hydrocarbon can produce mixtures containing one or more of H2, CO, H2O, CO2, and a lower hydrocarbon such as ethane or ethylene. The reformation of the gaseous hydrocarbon can produce low amounts of CO2 and H2O, e.g. about 15 mol-% or less.

Improve The Efficiency Of The Study Of Complex Reservoirs And Hydrocarbon Deposits - East Baghdad Field

Directory of Open Access Journals (Sweden)

Sudad H. Al-Obaidi

2015-08-01

Full Text Available Practical value of this work consists in increasing the efficiency of exploration for oil and gas fields in Eastern Baghdad by optimizing and reducing the complex of well logging coring sampling and well testing of the formation beds and computerizing the data of interpretation to ensure the required accuracy and reliability of the determination of petrophysical parameters that will clarify and increase proven reserves of hydrocarbon fields in Eastern Baghdad. In order to calculate the most accurate water saturation values for each interval of Zubair formation a specific modified form of Archie equation corresponding to this formation was developed.

Polymorphism of the aryl-hydrocarbon receptor gene in intron 10 of human cancers

Directory of Open Access Journals (Sweden)

M. Rocas

2011-11-01

Full Text Available Polychlorinated dibenzo-p-dioxins (PCDDs and related halogenated aromatic hydrocarbons (e.g., PCDFs, often called "dioxins", are ubiquitously present environmental contaminants. Some of them, notably 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD, are among the most toxic synthetic compounds known. The biological effects of dioxins are mediated via the aryl hydrocarbon receptor (AhR. Mutations in the AhR transactivation domain are linked to sensitivity to the acute lethality of TCDD. We present here a study of AhR gene polymorphism in normal and cancer human tissues affecting pre-mRNA splicing in the AhR gene-coding transactivation domain region (exon 10, intron 10, exon 11 region, previously shown to be associated with AhR dysfunction. We tested 126 pairs of normal and cancer tissue samples from liver, lung, stomach, kidney, mucous, breast, and pancreas of 49 males and 77 females (45-70 years of age. We used in vitro splicing assay, RT-PCR and sequencing methods. Our results showed that in an in vitro system it is possible to reconstitute cellular pre-mRNA splicing events. Tested cancer tissues did not contain mutations in the AhR transactivation domain region when the DNA sequences were compared with those from normal tissues. There were also no differences in AhR mRNA splice variants between normal and malignant breast tissues and no polymorphisms in the studied regions or cDNA.

Permeable bio-reactive barriers for hydrocarbon remediation in Antarctica

Energy Technology Data Exchange (ETDEWEB)

Mumford, K.A.; Stevens, G.W.; Gore, D.B. [Melbourne Univ., Victoria (Australia). Dept. of Chemical and Biomoleculuar Engineering, Particulate Fluids Processing Centre; Snape, I.; Rayner, J.L. [Australian Antarctic Div., Kingston, Tasmania (Australia); Gore, D.B. [Macquarie Univ., Sydney, NSW (Australia). Dept. of Environmental Science

2010-07-01

This study assessed the performance of a permeable bio-reactive barrier designed to treat contaminated water. The bio-reactive barrier was installed at a fuel spill site located in the Windmill Islands, Antarctica. A funnel and gate design was used to prevent contaminant migration beyond the barrier location as well as to ensure controlled nutrient delivery. The study also investigated the performance of the bio-reactive barrier in regions with freeze-thaw conditions. The 4-year project was also conducted to assess optimal conditions for enhancing the barrier's ability to degrade hydrocarbons.

Bioremediation of Petroleum Hydrocarbon Contaminated Sites

Energy Technology Data Exchange (ETDEWEB)

Fallgren, Paul

2009-03-30

Bioremediation has been widely applied in the restoration of petroleum hydrocarbon-contaminated. Parameters that may affect the rate and efficiency of biodegradation include temperature, moisture, salinity, nutrient availability, microbial species, and type and concentration of contaminants. Other factors can also affect the success of the bioremediation treatment of contaminants, such as climatic conditions, soil type, soil permeability, contaminant distribution and concentration, and drainage. Western Research Institute in conjunction with TechLink Environmental, Inc. and the U.S. Department of Energy conducted laboratory studies to evaluate major parameters that contribute to the bioremediation of petroleum-contaminated drill cuttings using land farming and to develop a biotreatment cell to expedite biodegradation of hydrocarbons. Physical characteristics such as soil texture, hydraulic conductivity, and water retention were determined for the petroleum hydrocarbon contaminated soil. Soil texture was determined to be loamy sand to sand, and high hydraulic conductivity and low water retention was observed. Temperature appeared to have the greatest influence on biodegradation rates where high temperatures (>50 C) favored biodegradation. High nitrogen content in the form of ammonium enhanced biodegradation as well did the presence of water near field water holding capacity. Urea was not a good source of nitrogen and has detrimental effects for bioremediation for this site soil. Artificial sea water had little effect on biodegradation rates, but biodegradation rates decreased after increasing the concentrations of salts. Biotreatment cell (biocell) tests demonstrated hydrocarbon biodegradation can be enhanced substantially when utilizing a leachate recirculation design where a 72% reduction of hydrocarbon concentration was observed with a 72-h period at a treatment temperature of 50 C. Overall, this study demonstrates the investigation of the effects of

The marine bacterium Marinobacter hydrocarbonoclasticus SP17 degrades a wide range of lipids and hydrocarbons through the formation of oleolytic biofilms with distinct gene expression profiles.

Science.gov (United States)

Mounier, Julie; Camus, Arantxa; Mitteau, Isabelle; Vaysse, Pierre-Joseph; Goulas, Philippe; Grimaud, Régis; Sivadon, Pierre

2014-12-01

Hydrophobic organic compounds (mainly lipids and hydrocarbons) represent a significant part of the organic matter in marine waters, and their degradation has an important impact in the carbon fluxes within oceans. However, because they are nearly insoluble in the water phase, their degradation by microorganisms occurs at the interface with water and thus requires specific adaptations such as biofilm formation. We show that Marinobacter hydrocarbonoclasticus SP17 develops biofilms, referred to as oleolytic biofilms, on a large variety of hydrophobic substrates, including hydrocarbons, fatty alcohols, fatty acids, triglycerides, and wax esters. Microarray analysis revealed that biofilm growth on n-hexadecane or triolein involved distinct genetic responses, together with a core of common genes that might concern general mechanisms of biofilm formation. Biofilm growth on triolein modulated the expression of hundreds of genes in comparison with n-hexadecane. The processes related to primary metabolism and genetic information processing were downregulated. Most of the genes that were overexpressed on triolein had unknown functions. Surprisingly, their genome localization was restricted to a few regions identified as putative genomic islands or mobile elements. These results are discussed with regard to the adaptive responses triggered by M. hydrocarbonoclasticus SP17 to occupy a specific niche in marine ecosystems. © 2014 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

Precipitation and ice core isotopes from the Asian Summer Monsoon region reflect coherent ENSO variability

Science.gov (United States)

Cai, Z.; Tian, L.; Bowen, G. J.

2017-12-01

Oxygen isotope signals (δ18O) from paleo-archives are important proxies for past Asian Summer Monsoon (ASM) climate reconstruction. However, causes of interannual variation in the δ18O values of modern precipitation across the ASM region remain in argument. We report interannual δ18O variation in southern Tibetan Plateau precipitation based on long-term observations at Lhasa. These data, together with precipitation δ18O records from five Global Network of Isotopes in Precipitation (GNIP) stations and two ice core δ18O records, were used to define a regional metric of ASM precipitation δ18O (ASMOI). Back-trajectory analyses for rainy season precipitation events indicate that moisture sources vary little between years with relatively high and low δ18O values, a result that is consistent for the south (Lhasa), southeast (Bangkok), and east ASM regions (Hong Kong). In contrast, δ18O values at these three locations are significantly correlated with convection in the estimated source regions and along transport paths. These results suggest that upstream convection, rather than moisture source change, causes interannual variation in ASM precipitation δ18O values. Contrasting values of the ASMOI in El Niño and La Niña years reveal a positive isotope-El Niño Southern Oscillation (ENSO) response (e.g., high values corresponding to warm phases), which we interpret as a response to changes in regional convection. We show that the isotope-ENSO response is amplified at high elevation sites and during La Niña years. These findings should improve interpretations of paleo-δ18O data as a proxy for past ASM variation and provide new opportunities to use data from this region to study paleo-ENSO activity.

Degradation of petroleum hydrocarbons in a laboratory aquifer column

International Nuclear Information System (INIS)

Billowits, M.; Whyte, L.; Greer, C.; Ramsay, J.

1998-01-01

One of the primary mechanisms for eliminating hydrocarbon pollutants from the environment is degradation of hydrocarbons by indigenous microorganisms. This report describes a study in which samples from a petroleum polluted shallow aquifer in the Yukon were used which contained a hundred times greater concentration of psychrotropic bacteria than mesophilic bacteria. Results showed a maximum degradation of 47 per cent of the total petroleum hydrocarbon in columns which simulated the aquifer conditions and to which nutrients were added. It was concluded that although in this case bioaugmentation of the columns with a psychrotropic hydrocarbon-degrading consortium increased microbial numbers, total petroleum hydrocarbon degradation was not much greater than could be achieved by remediation with nutrients alone

Hydrocarbons in Argentina: networks, territories, integration

International Nuclear Information System (INIS)

Carrizo, S.C.

2003-12-01

Argentinean hydrocarbons networks have lived a huge reorganizing the structure, after the State reform in the 90's. Activities deregulation and the privatization of YPF and Gas del Estado forced the sector re-concentration, since then dominated by foreign companies, leaded by Repsol YPF. The hydrocarbons federalization contributed to the weakening and un-capitalization loss of wealth of the State. These changes resulted in an increase of the hydrocarbons production allowing to achieve the self-supply. Nevertheless, the expansion of internal networks has not been large enough to ensure the coverage of new requirements. Besides, several infrastructures have been built up to join external markets. National networks are connected to those of near neighboring countries. This integration is an opportunity for the 'South Cone' countries to enhance their potentials. In the country, hydrocarbons territories undergo the reorganizing the structure effects (unemployment, loss of territorial identity, etc). With many difficulties and very different possibilities, those territories, like Comodoro Rivadavia, Ensenada et and Bahia Blanca, look for their re-invention. (author)

Exploring the relationship between polycyclic aromatic hydrocarbons and sedimentary organic carbon in three Chinese lakes

Energy Technology Data Exchange (ETDEWEB)

Wu, Fengchang; Xu, Libin; Liao, Haiqing; Zhao, Xiaoli [Chinese Research Academy of Environmental Sciences, Beijing (China). State Key Lab. of Environmental Criteria and Risk Assessment; Sun, Yongge [Zhejiang Univ., Hangzhou (China). Inst. of Environmental and Biogeochemistry; Guo, Jianyang [Chinese Academy of Sciences, Guiyang (China). State Key Lab. of Environmental Geochemistry

2012-05-15

Purpose: Previous studies have shown a positive correlation between concentrations of polycyclic aromatic hydrocarbons (PAHs) and total organic carbon (TOC) in lake sediments. However, with respect to the complex organic matter in recent sediments, it is still unclear which part of TOC plays a key role in controlling PAHs distributions in natural sediments. The aim of this study was to examine the relationships between PAHs and TOC components of different origins in lake sediments. Materials and methods: Sediment cores from three Chinese lakes with different trophic conditions - Lakes Bosten, Dianchi, and Poyang - were collected using a piston core sampler. The cores were sectioned into 1- or 2-cm intervals immediately after collection and transported on ice to the laboratory where they were stored at -20 C. The subsamples were freeze-dried and ground with a mortar and pestle for analyses. PAHs were analyzed by GC-MS and TOC was determined with a PE elemental analyzer after the removal of carbonates. Rock-Eval 6 pyrolysis technique was used to deconvolute the TOC in the sediments into free and volatile hydrocarbons (S1), kerogen-derived hydrocarbons (S2), and residual carbon (RC); S2 was further separated into thermal less stable macromolecular organic matter (S2a) and high molecular weight kerogens (S2b). Results and discussion: Positive correlations between TOC and PAHs were observed in these lakes. Results show that the more labile, minor components of TOC (S1 and S2a) played a more important role in controlling PAH distributions than the major components of TOC (S2b and RC), probably due to the different accessibilities of the organic components. The algae-derived organic carbon had a greater influence on the distribution of low molecular weight PAHs than that of high molecular weight PAHs in sediments. This suggests that PAHs scavenging in the water column by algae is mainly targeted at low molecular weight PAHs, and that preferential scavenging of low

Bioremediation in soil contaminated with hydrocarbons in Colombia.

OpenAIRE

María Alejandra Trujillo Toro; Juan Fernando Ramírez Quirama

2012-01-01

This study analyzes bioremediation processes of hydrocarbon contaminated soils in Colombia as a sustainable alternative to the deterioration of environmental quality by hydrocarbon spillage. According to national and international environmental law, all waste contaminated with hydrocarbons is considered dangerous waste, and therefore it cannot be released in the ground, water or be incinerated. Such legislation has motivated companies around the world to implement treatment processes for cont...

Hydrocarbon productivities in different Botryococcus strains: comparative methods in product quantification.

Science.gov (United States)

Eroglu, Ela; Okada, Shigeru; Melis, Anastasios

2011-08-01

Six different strains of the green microalgae Botryococcus belonging to the A-race or B-race, accumulating alkadiene or botryococcene hydrocarbons, respectively, were compared for biomass and hydrocarbon productivities. Biomass productivity was assessed gravimetrically upon strain growth in the laboratory under defined conditions. Hydrocarbon productivities were measured by three different and independent experimental approaches, including density equilibrium of the intact cells and micro-colonies, spectrophotometric analysis of hydrocarbon extracts, and gravimetric quantitation of eluted hydrocarbons. All three hydrocarbon-quantitation methods yielded similar results for each of the strains examined. The B-race microalgae Botryococcus braunii var. Showa and Kawaguchi-1 constitutively accumulated botryococcene hydrocarbons equivalent to 30% and 20%, respectively, of their overall biomass. The A-race microalgae Botryococcus braunii, varieties Yamanaka, UTEX 2441 and UTEX LB572 constitutively accumulated alkadiene hydrocarbons ranging from 14% to 13% and 10% of their overall biomass, respectively. Botryococcus sudeticus (UTEX 2629), a morphologically different green microalga, had the lowest hydrocarbon accumulation, equal to about 3% of its overall biomass. Results validate the density equilibrium and spectrophotometric analysis methods in the quantitation of botryococcene-type hydrocarbons. These analytical advances will serve in the screening and selection of B. braunii and of other microalgae in efforts to identify those having a high hydrocarbon content for use in commercial applications.

Radiation-induced volatile hydrocarbon production in platelets

International Nuclear Information System (INIS)

Radha, E.; Vaishnav, Y.N.; Kumar, K.S.; Weiss, J.F.

1989-01-01

Generation of volatile hydrocarbons (ethane, pentane) as a measure of lipid peroxidation was followed in preparations from platelet-rich plasma irradiated in vitro. The hydrocarbons in the headspace of sealed vials containing irradiated and nonirradiated washed platelets, platelet-rich plasma, or platelet-poor plasma increased with time. The major hydrocarbon, pentane, increased linearly and significantly with increasing log radiation dose, suggesting that reactive oxygen species induced by ionizing radiation result in lipid peroxidation. Measurements of lipid peroxidation products may give an indication of suboptimal quality of stored and/or irradiated platelets

Waste Plastic Converting into Hydrocarbon Fuel Materials

Energy Technology Data Exchange (ETDEWEB)

Sarker, Moinuddin; Mamunor Rashid, Mohammad; Molla, Mohammad

2010-09-15

The increased demand and high prices for energy sources are driving efforts to convert organic compounds into useful hydrocarbon fuels. Although much of this work has focused on biomass, there are strong benefits to deriving fuels from waste plastic material. Natural State Research Inc. (NSR) has invented a simple and economically viable process to decompose the hydrocarbon polymers of waste plastic into the shorter chain hydrocarbon of liquid fuel (patent pending). The method and principle of the production / process will be discussed. Initial tests with several widely used polymers indicate a high potential for commercialization.

Conversion of hydrocarbon oils into motor fuels

Energy Technology Data Exchange (ETDEWEB)

1937-11-09

The abstract describes a process for producing lower boiling hydrocarbon motor fuels with a starting material of wide boiling range composed primarily of hydrocarbon oils boiling substantially above the boiling range of the desired product. Separate catalytic and pyrolytic conversion zones are simultaneously maintained in an interdependent relationship. Higher boiling constituents are separated from residual constituents by fractionation while desirable reaction conditions are maintained. All or at least a portion of the products from the catalytic and pyrolytic conversion zones are blended to yield the desired lower boiling hydrocarbons or motor fuels.

Estimating Emissions of Toxic Hydrocarbons from Natural Gas Production Sites in the Barnett Shale Region of Northern Texas.

Science.gov (United States)

Marrero, Josette E; Townsend-Small, Amy; Lyon, David R; Tsai, Tracy R; Meinardi, Simone; Blake, Donald R

2016-10-04

Oil and natural gas operations have continued to expand and move closer to densely populated areas, contributing to growing public concerns regarding exposure to hazardous air pollutants. During the Barnett Shale Coordinated Campaign in October, 2013, ground-based whole air samples collected downwind of oil and gas sites revealed enhancements in several potentially toxic volatile organic compounds (VOCs) when compared to background values. Molar emissions ratios relative to methane were determined for hexane, benzene, toluene, ethylbenzene, and xylene (BTEX compounds). Using methane leak rates measured from the Picarro mobile flux plane (MFP) system and a Barnett Shale regional methane emissions inventory, the rates of emission of these toxic gases were calculated. Benzene emissions ranged between 51 ± 4 and 60 ± 4 kg h -1 . Hexane, the most abundantly emitted pollutant, ranged from 642 ± 45 to 1070 ± 340 kg h -1 . While observed hydrocarbon enhancements fall below federal workplace standards, results may indicate a link between emissions from oil and natural gas operations and concerns about exposure to hazardous air pollutants. The larger public health risks associated with the production and distribution of natural gas are of particular importance and warrant further investigation, particularly as the use of natural gas increases in the United States and internationally.

Contribution of the C-terminal region within the catalytic core domain of HIV-1 integrase to yeast lethality, chromatin binding and viral replication

Directory of Open Access Journals (Sweden)

Belhumeur Pierre

2008-11-01

Full Text Available Abstract Background HIV-1 integrase (IN is a key viral enzymatic molecule required for the integration of the viral cDNA into the genome. Additionally, HIV-1 IN has been shown to play important roles in several other steps during the viral life cycle, including reverse transcription, nuclear import and chromatin targeting. Interestingly, previous studies have demonstrated that the expression of HIV-1 IN induces the lethal phenotype in some strains of Saccharomyces cerevisiae. In this study, we performed mutagenic analyses of the C-terminal region of the catalytic core domain of HIV-1 IN in order to delineate the critical amino acid(s and/or motif(s required for the induction of the lethal phenotype in the yeast strain HP16, and to further elucidate the molecular mechanism which causes this phenotype. Results Our study identified three HIV-1 IN mutants, V165A, A179P and KR186,7AA, located in the C-terminal region of the catalytic core domain of IN that do not induce the lethal phenotype in yeast. Chromatin binding assays in yeast and mammalian cells demonstrated that these IN mutants were impaired for the ability to bind chromatin. Additionally, we determined that while these IN mutants failed to interact with LEDGF/p75, they retained the ability to bind Integrase interactor 1. Furthermore, we observed that VSV-G-pseudotyped HIV-1 containing these IN mutants was unable to replicate in the C8166 T cell line and this defect was partially rescued by complementation with the catalytically inactive D64E IN mutant. Conclusion Overall, this study demonstrates that three mutations located in the C-terminal region of the catalytic core domain of HIV-1 IN inhibit the IN-induced lethal phenotype in yeast by inhibiting the binding of IN to the host chromatin. These results demonstrate that the C-terminal region of the catalytic core domain of HIV-1 IN is important for binding to host chromatin and is crucial for both viral replication and the promotion of

Distilling hydrocarbons, etc

Energy Technology Data Exchange (ETDEWEB)

Turner, C

1917-11-23

In the fractional or destructive distillation of hydrocarbon oils or other liquids, the pressure in the still is raised and lowered alternately. The still is closed to raise the pressure, and is opened to lower the pressure rapidly solely by expansion of the vapors. The operation is effected without intermittent cooling, except such as may occur during the lowering of the pressure. In distilling hydrocarbon oil, pressure steam is blown into the oil until the pressure reaches 5 lb/in./sup 2/. The vapor outlet is then opened until the pressure falls to 2 lb/in./sup 2/, whereupon the vapor outlet is closed and steam is again admitted. The operation is continued until the steam, which is of 20 lb pressure, no longer effects distillation; after this stage, superheated steam is used.

Stress dependence of permeability of intact and fractured shale cores.

Science.gov (United States)

van Noort, Reinier; Yarushina, Viktoriya

2016-04-01

Whether a shale acts as a caprock, source rock, or reservoir, understanding fluid flow through shale is of major importance for understanding fluid flow in geological systems. Because of the low permeability of shale, flow is thought to be largely confined to fractures and similar features. In fracking operations, fractures are induced specifically to allow for hydrocarbon exploration. We have constructed an experimental setup to measure core permeabilities, using constant flow or a transient pulse. In this setup, we have measured the permeability of intact and fractured shale core samples, using either water or supercritical CO2 as the transporting fluid. Our measurements show decreasing permeability with increasing confining pressure, mainly due to time-dependent creep. Furthermore, our measurements show that for a simple splitting fracture, time-dependent creep will also eliminate any significant effect of this fracture on permeability. This effect of confinement on fracture permeability can have important implications regarding the effects of fracturing on shale permeability, and hence for operations depending on that.

Primary biodegradation of petroleum hydrocarbons in seawater

Energy Technology Data Exchange (ETDEWEB)

Comber, M.I.H.; Den Haan, K.H.; Djemel, N.; Eadsforth, C.V.; King, D.; Paumen, M.L.; Parkerton, T.; Dmytrasz, B.

2012-12-15

This report describes primary biodegradation experiments performed to determine the persistence of higher molecular weight petroleum hydrocarbons in seawater. Results from the biodegradation experiments show that the majority of tested petroleum hydrocarbons have half-lives in seawater less than 60 days.

Aspects of petroleum hydrocarbon metabolism in marine animals

Science.gov (United States)

Mironov, O. G.

1980-03-01

Studies on hydrocarbon composition of Black Sea mussels Mytilus galloprovincialis sampled from different habitats indicate that the quantity and composition of hydrocarbons distributed in the molluscs depend on season and sea-water quality. The data obtained under experimental conditions testify to the possibility of hydrocarbon concentration in mussel tissues after death. During filtration in sea water containing oil and oil products, these pollutants are bound into faeces and pseudofaeces which contain a greater percentage of aromatic compounds than the oil initially present in sea water. Quantitative data are presented on hydrocarbon changes in mussel excretory products during transfer from oil-polluted to clean sea water. When Black Sea crabs Eriphia verrucosa are fed with mussels containing fuel-oil components accumulated from sea water, the pollutants concentrate in the whole body of the crab. This is in contrast to parenteral oil uptake, which leads to a concentration of most of the hydrocarbon in the muscles.

Development of oil hydrocarbon fingerprinting and identification techniques

International Nuclear Information System (INIS)

Wang Zhendi; Fingas, Merv F.

2003-01-01

Oil, refined product, and pyrogenic hydrocarbons are the most frequently discovered contaminants in the environment. To effectively determine the fate of spilled oil in the environment and to successfully identify source(s) of spilled oil and petroleum products is, therefore, extremely important in many oil-related environmental studies and liability cases. This article briefly reviews the recent development of chemical analysis methodologies which are most frequently used in oil spill characterization and identification studies and environmental forensic investigations. The fingerprinting and data interpretation techniques discussed include oil spill identification protocol, tiered analytical approach, generic features and chemical composition of oils, effects of weathering on hydrocarbon fingerprinting, recognition of distribution patterns of petroleum hydrocarbons, oil type screening and differentiation, analysis of 'source-specific marker' compounds, determination of diagnostic ratios of specific oil constituents, stable isotopic analysis, application of various statistical and numerical analysis tools, and application of other analytical techniques. The issue of how biogenic and pyrogenic hydrocarbons are distinguished from petrogenic hydrocarbons is also addressed

Total site integration of light hydrocarbons separation process

OpenAIRE

Ulyev, L.; Vasilyev, M.; Maatouk, A.; Duic, Neven; Khusanovc, Alisher

2016-01-01

Ukraine is the largest consumer of hydrocarbons per unit of production in Europe (Ukraine policy review, 2006). The most important point is a reduction of energy consumption in chemical and metallurgical industries as a biggest consumer. This paper deals with energy savings potential of light hydrocarbons separation process. Energy consumption of light hydrocarbons separation process processes typical of Eastern European countries were analysed. Process Integration (PI) was used to perform a ...

The Attribute for Hydrocarbon Prediction Based on Attenuation

International Nuclear Information System (INIS)

Hermana, Maman; Harith, Z Z T; Sum, C W; Ghosh, D P

2014-01-01

Hydrocarbon prediction is a crucial issue in the oil and gas industry. Currently, the prediction of pore fluid and lithology are based on amplitude interpretation which has the potential to produce pitfalls in certain conditions of reservoir. Motivated by this fact, this work is directed to find out other attributes that can be used to reduce the pitfalls in the amplitude interpretation. Some seismic attributes were examined and studies showed that the attenuation attribute is a better attribute for hydrocarbon prediction. Theoretically, the attenuation mechanism of wave propagation is associated with the movement of fluid in the pore; hence the existence of hydrocarbon in the pore will be represented by attenuation attribute directly. In this paper we evaluated the feasibility of the quality factor ratio of P-wave and S-wave (Qp/Qs) as hydrocarbon indicator using well data and also we developed a new attribute based on attenuation for hydrocarbon prediction -- Normalized Energy Reduction Stack (NERS). To achieve these goals, this work was divided into 3 main parts; estimating the Qp/Qs on well log data, testing the new attribute in the synthetic data and applying the new attribute on real data in Malay Basin data. The result show that the Qp/Qs is better than Poisson's ratio and Lamda over Mu as hydrocarbon indicator. The curve, trend analysis and contrast of Qp/Qs is more powerful at distinguishing pore fluid than Poisson ratio and Lamda over Mu. The NERS attribute was successful in distinguishing the hydrocarbon from brine on synthetic data. Applying this attribute on real data on Malay basin, the NERS attribute is qualitatively conformable with the structure and location where the gas is predicted. The quantitative interpretation of this attribute for hydrocarbon prediction needs to be investigated further

BWR type reactor core

International Nuclear Information System (INIS)

Tatemichi, Shin-ichiro.

1981-01-01

Purpose: To eliminate the variation in the power distribution of a BWR type reactor core in the axial direction even if the flow rate is increased or decreased by providing a difference in the void coefficient between the upper part and the lower parts of the reactor core, and increasing the void coefficient at the lower part of the reactor core. Constitution: The void coefficient of the lower region from the center to the lower part along the axial direction of a nuclear fuel assembly is increased to decrease the dependence on the flow rate of the axial power distribution of the nuclear fuel assembly. That is, a water/fuel ratio is varied, the water in non-boiled region is increased or the neutron spectrum is varied so as to vary the void coefficient. In order to exemplify it, the rate of the internal pellets of the fuel rod of the nuclear fuel assembly or the shape of the channel box is varied. Accordingly, the power does not considerably vary even if the flow rate is altered since the power is varied in the power operation. (Yoshihara, H.)

Temperature-dependent mid-IR absorption spectra of gaseous hydrocarbons

International Nuclear Information System (INIS)

Klingbeil, Adam E.; Jeffries, Jay B.; Hanson, Ronald K.

2007-01-01

Quantitative mid-IR absorption spectra (2500-3400 cm -1 ) for 12 pure hydrocarbon compounds are measured at temperatures ranging from 25 to 500 deg. C using an FTIR spectrometer. The hydrocarbons studied are n-pentane, n-heptane, n-dodecane, 2,2,4-trimethyl-pentane (iso-octane), 2-methyl-butane, 2-methyl-pentane, 2,4,4-trimethyl-1-pentene, 2-methyl-2-butene, propene, toluene, m-xylene, and ethylbenzene. Room-temperature measurements of neat hydrocarbon vapor were made with an instrument resolution of both 0.1 and 1 cm -1 (FWHM) to confirm that the high-resolution setting was required only to resolve the propene absorption spectrum while the spectra of the other hydrocarbons could be resolved with 1 cm -1 resolution. High-resolution (0.1 cm -1 ), room-temperature measurements of neat hydrocarbons were made at low pressure (∼1 Torr, 133 Pa) and compared to measurements of hydrocarbon/N 2 mixtures at atmospheric pressure to verify that no pressure broadening could be observed over this pressure range. The temperature was varied between 25 and 500 o C for atmospheric-pressure measurements of hydrocarbon/N 2 mixtures (X hydrocarbon ∼0.06-1.5%) and it was found that the absorption cross section shows simple temperature-dependent behavior for a fixed wavelength over this temperature range. Comparisons with previous FTIR data over a limited temperature range and with high-resolution laser absorption data over a wide temperature range show good agreement

Using microorganisms to aid in hydrocarbon degradation

International Nuclear Information System (INIS)

Black, W.; Zamora, J.

1993-01-01

Aliphatic hydrocarbons are threatening the potable water supply and the aquatic ecosystem. Given the right microbial inhabitant(s), a large portion of these aliphatic hydrocarbons could be biodegraded before reaching the water supply. The authors' purpose is to isolate possible oil-degrading organisms. Soil samples were taken from hydrocarbon-laden soils at petroleum terminals, a petroleum refinery waste-treatment facility, a sewage-treatment plant grease collector, a site of previous bioremediation, and various other places. Some isolates known to be good degraders were obtained from culture collection services. These samples were plated on a 10w-30 multigrade motor oil solid medium to screen for aliphatic hydrocarbon degraders. The degrading organisms were isolated, identified, and tested (CO 2 evolution, BOD, and COD) to determine the most efficient degrader(s). Thirty-seven organisms were tested, and the most efficient degraders were Serratia marcescens, Escherichia coli, and Enterobacter agglomerans

Nitrocarburising in ammonia-hydrocarbon gas mixtures

DEFF Research Database (Denmark)

Pedersen, Hanne; Christiansen, Thomas; Somers, Marcel A. J.

2010-01-01

The present work investigates the possibility of nitrocarburising in ammonia-acetylene-hydrogen and ammoniapropene- hydrogen gas mixtures, where unsaturated hydrocarbon gas is the carbon source during nitrocarburising. Consequently, nitrocarburising is carried out in a reducing atmosphere...... microscopy and X-ray diffraction analysis. It is shown that the use of unsaturated hydrocarbon gas in nitrocarburising processes is a viable alternative to traditional nitrocarburising methods....

George A. Olah, Carbocation and Hydrocarbon Chemistry

Science.gov (United States)

dropdown arrow Site Map A-Z Index Menu Synopsis George A. Olah, Carbocation and Hydrocarbon Chemistry George Olah received the 1994 Nobel Prize in Chemistry "for his contribution to carbocation chemistry" and his 'role in the chemistry of hydrocarbons. In particular, he developed superacids

Detection of irradiated meats by hydrocarbon method

International Nuclear Information System (INIS)

Goto, Michiko; Miyakawa, Hiroyuki; Fujinuma, Kenji; Ozawa, Hideki

2005-01-01

Meats, for example, lamb, razorback, wild duck and turkey were irradiated by gamma ray, and the amounts of hydrocarbons formed from fatty acids were measured. Since C 20:0 was found from wild duck and turkey. C 1-18:1 was recommended for internal standard. Good correlation was found between the amount of hydrocarbons and the doses of gamma irradiation. This study shows that such hydrocarbons induced after radiation procedure as C 1,7-16:2 , C 8-17:1 , C 1-14:1 , and C 15:0 may make it possible to detect irradiated lamb, razorback, wild duck and turkey. (author)

Method of recovering hydrocarbons from oil shale

Energy Technology Data Exchange (ETDEWEB)

Walton, D.K.; Slusser, M.S.

1970-11-24

A method is described for recovering hydrocarbons from an oil-shale formation by in situ retorting. A well penetrating the formation is heated and gas is injected until a pressure buildup within the well is reached, due to a decrease in the conductivity of naturally occurring fissures within the formation. The well is then vented, in order to produce spalling of the walls. This results in the formation of an enlarged cavity containing rubberized oil shale. A hot gas then is passed through the rubberized oil shale in order to retort hydrocarbons and these hydrocarbons are recovered from the well. (11 claims)

Political risks of hydrocarbon deposit development in the Arctic seas of the Russian Federation

International Nuclear Information System (INIS)

Bolsunovskaya, Y A; Boyarko, G Yu; Bolsunovskaya, L M

2014-01-01

Nowadays the process of Arctic development has a long-term international cooperation character. Economic and geopolitical interests of both arctic and non-arctic countries meet in the region. Apart from resource development issues, there are problems concerning security, sustainable development and some others issues conditioned by climate and geographical characteristics of the region. Strategic analysis of political risks for the Russian Federation is carried out. The analysis reveals that political risks of hydrocarbon deposits development in the RF arctic seas appear as lack of coordination with arctic countries in solving key regional problems, failure to follow international agreements. Such inconsistency may lead to political risks, which results in strained situation in the region

Bioremediation of petroleum hydrocarbons in soil environments

International Nuclear Information System (INIS)

Rowell, M.J.; Ashworth, J.; Qureshi, A.A.

1992-12-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed via a literature survey and discussions with workers in relevant disciplines. The impacts of hydrocarbons on soil are discussed along with a range of methods available to assist in their decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, sludges, asphalts and bitumens, drilling mud residues, creosote tars, and some pesticides. The degradability of hydrocarbons largely depends upon their aqueous solubility and their adsorption on soil surfaces and, therefore, is related to their molecular structures. The ease of decomposition decreases with increasing complexity of structure, in the order aliphatics > aromatics > heterocyclics and asphaltenes (most recalcitrant). Most soils contain an adequate population of microorganisms and hence bioaugmentation may only be needed in special circumstances. Decomposition is fastest in soils where the hydrocarbon loading rate, aeration, nutrition, moisture, and pH are all optimized. At spill sites there is little control over the application rate, although containment measures can assist in either limiting contamination or distributing it more evenly. The enhancement of bioremediation is discussed in light of all these factors. Other techniques such as enhanced aeration, hydrocarbon decomposition by anaerobic processes, surfactants, and burning are also discussed. 211 refs., 11 figs., 10 tabs

Emissions of hydrocarbons from combustion of biofuels

International Nuclear Information System (INIS)

Olsson, Mona; Persson, Eva Marie.

1991-10-01

Evaluations and measurements of emissions of hydrocarbons from power plants with a capacity exceeding 1 MW using biofuels (wood fuels and peat) have been studied in order to identify and quantify the emissions of incompletely combusted hydrocarbons. The influence of the type of fuel and the combustion technology applied were also studied, using literature references. The report summarizes monitoring results from a number of plants using biofuels. The reported emissions from the different plants can not be compared as they are relatively few and the test results have been obtained under various conditions using different methods of testing and analysis. The methods used are often poorly documented in the studied reports. Few investigations of emissions of hydrocarbons from plants in the range of 1 to 10 MW have been carried out. The plant and the technology used are important factors determining the amount and type of emissions of hydrocarbons. Larger temporary emissions can occur during start up, operational disturbances or when using fuel of inhomogeneous quality. In order to minimize the emissions the combustion process must be efficiently controlled, and a fuel of a hohogeneous quality must be used. The report also summarizes sampling and analysis methods used for monitoring emissions of hydrocarbons. (29 refs., 17 figs.)

Bioremediation of petroleum hydrocarbons in soil environments

Energy Technology Data Exchange (ETDEWEB)

Rowell, M J; Ashworth, J; Qureshi, A A

1992-12-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed via a literature survey and discussions with workers in relevant disciplines. The impacts of hydrocarbons on soil are discussed along with a range of methods available to assist in their decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, sludges, asphalts and bitumens, drilling mud residues, creosote tars, and some pesticides. The degradability of hydrocarbons largely depends upon their aqueous solubility and their adsorption on soil surfaces and, therefore, is related to their molecular structures. The ease of decomposition decreases with increasing complexity of structure, in the order aliphatics > aromatics > heterocyclics and asphaltenes (most recalcitrant). Most soils contain an adequate population of microorganisms and hence bioaugmentation may only be needed in special circumstances. Decomposition is fastest in soils where the hydrocarbon loading rate, aeration, nutrition, moisture, and pH are all optimized. At spill sites there is little control over the application rate, although containment measures can assist in either limiting contamination or distributing it more evenly. The enhancement of bioremediation is discussed in light of all these factors. Other techniques such as enhanced aeration, hydrocarbon decomposition by anaerobic processes, surfactants, and burning are also discussed. 211 refs., 11 figs., 10 tabs.

Geochemical interpretation of distribution of aromatic hydrocarbons in components of geologic environment of Pechora, Barents and Kara seas.

Science.gov (United States)

Kursheva, Anna; Petrova, Vera; Litvinenko, Ivan; Morgunova, Inna

2017-04-01

Information about the hydrocarbons content (including aromatic ones) in components of geologic environment allows to define common factors in distribution and correlation both nature and technogenic component, and also to reveal the sources of contamination. At that, it should be noted, that hydrocarbons are widely spread in lithosphere and create steady geochemical background, variations are caused here by specifics of initial organic matter, conditions of its accumulation and transformation. The basis of the study are the samples of sea water and deep sea sediments (more than 600 stations), collected in western sector of Arctic region (Pechora, Barents and Kara seas) during the scientific-research expeditions of FSBI "VNIIOkeangeologia" for the period 2000-2010. Total content of aromatic hydrocarbons was defined by spectrofluorometric method using analyzer «FLUORAT-Panorama-02». Certification of data was performed on representative samples based on contents and molecule structure of polycyclic aromatic hydrocarbons using GC-MS (Agilent 5973/6850 GC-MS System). Results of spectrofluorometric analysis of lipid fraction of organic matter of bottom sediments allowed to define specific parameters, which characterize various lithofacies groups of sediments. Thus, sandy residues are characterized by low level of aromatic hydrocarbons (ca. 4.3 μg/g) with prevalence of bi- and tri-aromatic compounds (λmax 270-310 nm). This correlates with low sorption capacity of coarse-grained sediments and absence of organic-mineral component, containing the breakdown products of initial organic matter. Tetra- and penta- aromatic structures prevail in clay sediments (ca. 13.0 μg/g), which are typical components of lipid fraction of organic matter of post sedimentation and early diagenetic stages of transformation. At that, changes of spectral characteristic of sediments in stratigraphic sequence completely reflect processes of diagenetic transformation of organic matter, including

Analysis of structural heterogeneities on drilled cores: a reservoir modeling oriented methodology; Analyse des heterogeneites structurales sur carottes: une methodologie axee vers la modelisation des reservoirs

Energy Technology Data Exchange (ETDEWEB)

Cortes, P.; Petit, J.P. [Montpellier-2 Univ., Lab. de Geophysique, Tectonique et Sedimentologie, UMR CNRS 5573, 34 (France); Guy, L. [ELF Aquitaine Production, 64 - Pau (France); Thiry-Bastien, Ph. [Lyon-1 Univ., 69 (France)

1999-07-01

The characterization of structural heterogeneities of reservoirs is of prime importance for hydrocarbons recovery. A methodology is presented which allows to compare the dynamic behaviour of fractured reservoirs and the observation of microstructures on drilled cores or surface reservoir analogues. (J.S.)

Hydrocarbon phytoremediation in the family Fabaceae--a review.

Science.gov (United States)

Hall, Jessica; Soole, Kathleen; Bentham, Richard

2011-04-01

Currently, studies often focus on the use of Poaceae species (grasses) for phytoremediation of hydrocarbon-contaminated soils. Research into the use of Fabaceae species (legumes) to remediate hydrocarbons in soils has been conducted, but these plants are commonly overlooked due to slower recorded rates of degradation compared with many grass species. Evidence in the literature suggests that in some cases Fabaceae species may increase total degradation of hydrocarbons and stimulate degradative capacity of the soil microbial community, particularly for contaminants which are normally more recalcitrant to degradation. As many recalcitrant hydrocarbons have negative impacts on human and ecosystem health, development of remediation options is crucial. Reconsideration of Fabaceae species for removal of such contaminants may lead to environmentally and economically sustainable technologies for remediation of contaminated sites.

The role of mass spectrometry in hydrocarbon analysis

International Nuclear Information System (INIS)

Kerenyi, E.

1980-01-01

Modern mass spectrometry has an outstandin.o role in solving problems concerning the composition and structure of hydrocarbon mixtures and their derivatives, petroleum and petrochemical products. Its efficiency in hydrocarbon analysis has been increased not only by high resolving power and computerized spectrum processing but also by the metastable ion spectrum technique promoting structural examinations, by mild ionization facilitating composition analysis, and by selective ion-detecting technique. The author presents the advantages of the metastable ion spectra, the field ionization, field desorption and other mild ionization methods, and finally, those of fragmentation analysis in connection with the examination of hydrocarbons and hydrocarbon derivatives. Examples taken from the literature and from the research work carried out in the Institute are also given. (author)

Enhancement of in situ Remediation of Hydrocarbon Contaminated Soil

Energy Technology Data Exchange (ETDEWEB)

Palmroth, M.

2006-07-01

Approximately 750 000 sites of contaminated land exist across Europe. The harmful chemicals found in Finnish soils include heavy metals, oil products, polyaromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), chlorophenols, and pesticides. Petroleum and petroleum products enter soil from ruptured oil pipelines, land disposal of refinery products, leaking storage tanks and through accidents. PAH contamination is caused by the spills of coal tar and creosote from coal gasification and wood treatment sites in addition to oil spills. Cleanup of soil by bioremediation is cheaper than by chemical and physical processes. However, the cleaning capacity of natural attenuation and in situ bioremediation is limited. The purpose of this thesis was to find feasible options to enhance in situ remediation of hydrocarbon contaminants. The aims were to increase the bioavailability of the contaminants and microbial activity at the subsurface in order to achieve higher contaminant removal efficiency than by intrinsic biodegradation alone. Enhancement of microbial activity and decrease of soil toxicity during remediation were estimated by using several biological assays. The performance of these assays was compared in order to find suitable indicators to follow the progress of remediation. Phytoremediation and chemical oxidation are promising in situ techniques to increase the degradation of hydrocarbons in soil. Phytoremediation is plant-enhanced decontamination of soil and water. Degradation of hydrocarbons is enhanced in the root zone by increased microbial activity and through the detoxifying enzymes of plants themselves. Chemical oxidation of contaminants by Fenton's reaction can produce degradation products which are more biodegradable than the parent compounds. Fenton's reaction and its modifications apply solutions of hydrogen peroxide and iron for the oxidation of organic chemicals. The cost of oxidation can be reduced by aiming at partial instead of full

National Gas Hydrate Program Expedition 01 offshore India; gas hydrate systems as revealed by hydrocarbon gas geochemistry

Science.gov (United States)

Lorenson, Thomas; Collett, Timothy S.

2018-01-01

The National Gas Hydrate Program Expedition 01 (NGHP-01) targeted gas hydrate accumulations offshore of the Indian Peninsula and along the Andaman convergent margin. The primary objectives of coring were to understand the geologic and geochemical controls on the accumulation of methane hydrate and their linkages to underlying petroleum systems. Four areas were investigated: 1) the Kerala-Konkan Basin in the eastern Arabian Sea, 2) the Mahanadi and 3) Krishna-Godavari Basins in the western Bay of Bengal, and 4) the Andaman forearc Basin in the Andaman Sea.Upward flux of methane at three of the four of the sites cored during NGHP-01 is apparent from the presence of seafloor mounds, seismic evidence for upward gas migration, shallow sub-seafloor geochemical evidence of methane oxidation, and near-seafloor gas composition that resembles gas from depth.The Kerala-Konkan Basin well contained only CO2 with no detectable hydrocarbons suggesting there is no gas hydrate system here. Gas and gas hydrate from the Krishna-Godavari Basin is mainly microbial methane with δ13C values ranging from −58.9 to −78.9‰, with small contributions from microbial ethane (−52.1‰) and CO2. Gas from the Mahanadi Basin was mainly methane with lower concentrations of C2-C5 hydrocarbons (C1/C2 ratios typically >1000) and CO2. Carbon isotopic compositions that ranged from −70.7 to −86.6‰ for methane and −62.9 to −63.7‰ for ethane are consistent with a microbial gas source; however deeper cores contained higher molecular weight hydrocarbon gases suggesting a small contribution from a thermogenic gas source. Gas composition in the Andaman Basin was mainly methane with lower concentrations of ethane to isopentane and CO2, C1/C2 ratios were mainly >1000 although deeper samples were compositions range from −65.2 to −80.7‰ for methane, −53.1 to −55.2‰ for ethane is consistent with mainly microbial gas sources, although one value recorded of −35.4‰ for propane

Nitrocarburizing in ammonia-hydrocarbon gas mixtures

DEFF Research Database (Denmark)

Pedersen, Hanne; Christiansen, Thomas; Somers, Marcel A. J.

2011-01-01

The present work investigates the possibility of nitrocarburising in ammonia-acetylene-hydrogen and ammonia-propene-hydrogen gas mixtures, where unsaturated hydrocarbon gas is the carbon source during nitrocarburising. Consequently, nitrocarburising is carried out in a reducing atmosphere...... microscopy and X-ray diffraction analysis. It is shown that the use of unsaturated hydrocarbon gas in nitrocarburising processes is a viable alternative to traditional nitrocarburising methods....

Source identification of hydrocarbons following environmental releases

Energy Technology Data Exchange (ETDEWEB)

Birkholz, D.A. [ALS Environmental, Edmonton, AB (Canada)

2010-07-01

Methods of identifying the sources of hydrocarbon contaminations were discussed in this PowerPoint presentation. Laboratories analyze for total petroleum hydrocarbons (TPH) by obtaining chromatograms of observed products. However, many petroleum products provide similar chromatograms. Several independent lines of evidence are needed for the purposes of accurate determination in legal applications. A case study of a lube oil plant spill was used to demonstrate the inconclusiveness of chromatograms and the need to determine petroleum biomarkers. Terpane, sterane, triaromatic sterane, isoprenoid, and alkylcyclohexane analyses were conducted to differentiate between the hydrocarbon samples. The analysis methods are being used with various soil, water, and crab species samples from the BP oil spill. Oil found at the different sites must be directly related to the spill. However, there are 3858 oil and gas platforms currently operating in the Gulf of Mexico. Ratios of biomarkers and polycyclic aromatic hydrocarbons (PAHs) are being developed to generate weight of evidence. A critical difference analysis was also presented. tabs., figs.

Seasonal and Diurnal Variations of Atmospheric Non-Methane Hydrocarbons in Guangzhou, China

Directory of Open Access Journals (Sweden)

Longfeng Li

2012-05-01

Full Text Available In recent decades, high ambient ozone concentrations have become one of the major regional air quality issues in the Pearl River Delta (PRD region. Non-methane hydrocarbons (NMHCs, as key precursors of ozone, were found to be the limiting factor in photochemical ozone formation for large areas in the PRD. For source apportioning of NMHCs as well as ozone pollution control strategies, it is necessary to obtain typical seasonal and diurnal patterns of NMHCs with a large pool of field data. To date, few studies have focused on seasonal and diurnal variations of NMHCs in urban areas of Guangzhou. This study explored the seasonal variations of most hydrocarbons concentrations with autumn maximum and spring minimum in Guangzhou. The diurnal variations of most anthropogenic NMHCs typically showed two-peak pattern with one at 8:00 in the morning and another at 20:00 in the evening, both corresponding to traffic rush hours in Guangzhou, whereas isoprene displayed a different bimodal diurnal curve. Propene, ethene, m, p-xylene and toluene were the four largest contributors to ozone formation in Guangzhou, based on the evaluation of individual NMHCs’ photochemical reactivity. Therefore, an effective strategy for controlling ozone pollution may be achieved by the reduction of vehicle emissions in Guangzhou.

Investigating the translation of Earth's inner core

DEFF Research Database (Denmark)

Day, Elizabeth A; Cormier, Vernon F; Geballe, Zachary M

2012-01-01

The Earth’s inner core provides unique insights into processes that are occurring deep within our Earth today, as well as processes that occurred in the past. The seismic structure of the inner core is complex, and is dominated by anisotropic and isotropic differences between the Eastern...... for models of a translating inner core. Additionally, we investigate the structure at the base of the outer core and the inner core boundary by analyzing PKP-Cdiff waves. The search for observable PKP-Cdiff is particularly concentrated in regions that are predicted to be actively freezing and melting...... and Western ‘hemispheres’ of the inner core. Recent geodynamical models suggest that this hemispherical dichotomy can be explained by a fast translation of the inner core. In these models one side of the inner core is freezing, while the other side is melting, leading to the development of different seismic...

Experimental comparison among hydrocarbon and oxygenated compounds for their elimination by three-way automotive catalysts

International Nuclear Information System (INIS)

Bart, J.M.; Prigent, M.F.

1992-01-01

Many hydrocarbon species are present in automotive exhaust gases, and three-way Pt-Rh catalysts are commonly used for their elimination. However, most published work on individual hydrocarbon conversion concerns their oxidation in simulated exhaust gases with excess oxygen. This paper reports that this study was therefore undertaken to determine the reactivity of saturated alkanes, olefins, acetylene, aromatics, alcohols or various other oxygenated compounds in steady state conditions with synthetic exhaust gases near stoichiometry. In a first series of measurements, conversion rates were determined as a function of temperature at stoichiometry. The partial pressure effect of O 2 , NO and H 2 O was then determined at constant temperature in the region of catalyst light-off. NO and mainly O 2 were shown to have a negative effect on the first terms of saturated alkane conversion under lean conditions. Water vapor has a positive effect in rich conditions (without SO 2 ), but is more pronounced for Pt-Rh than for a Pt catalyst. Finally, the role played by SO 2 in hydrocarbon conversion was evaluated

Chemical fingerprinting of hydrocarbon-contamination in soil.

Science.gov (United States)

Boll, Esther S; Nejrup, Jens; Jensen, Julie K; Christensen, Jan H

2015-03-01

Chemical fingerprinting analyses of 29 hydrocarbon-contaminated soils were performed to assess the soil quality and determine the main contaminant sources. The results were compared to an assessment based on concentrations of the 16 priority polycyclic aromatic hydrocarbons pointed out by the U.S. Environmental Protection Agency (EPAPAH16) and total petroleum hydrocarbon (TPH). The chemical fingerprinting strategy proposed in this study included four tiers: (i) qualitative analysis of GC-FID chromatograms, (ii) comparison of the chemical composition of both un-substituted and alkyl-substituted polycyclic aromatic compounds (PACs), (iii) diagnostic ratios of selected PACs, and (iv) multivariate data analysis of sum-normalized PAC concentrations. The assessment criteria included quantitative analysis of 19 PACs and C1-C4 alkyl-substituted homologues of naphthalene, fluorene, dibenzothiophene, phenanthrene, pyrene, and chrysene; and 13 oxygenated polycyclic aromatic compounds (O-PACs). The chemical composition of un-substituted and alkyl-substituted PACs and visual interpretation of GC-FID chromatograms were in combination successful in differentiating pyrogenic and petrogenic hydrocarbon sources and in assessing weathering trends of hydrocarbon contamination in the soils. Multivariate data analysis of sum-normalized concentrations could as a stand-alone tool distinguish between hydrocarbon sources of petrogenic and pyrogenic origin, differentiate within petrogenic sources, and detect weathering trends. Diagnostic ratios of PACs were not successful for source identification of the heavily weathered hydrocarbon sources in the soils. The fingerprinting of contaminated soils revealed an underestimation of PACs in petrogenic contaminated soils when the assessment was based solely on EPAPAH16. As alkyl-substituted PACs are dominant in petrogenic sources, the evaluation of the total load of PACs based on EPAPAH16 was not representative. Likewise, the O-PACs are not

Reflood behavior at low initial clad temperature in Slab Core Test Facility Core-II

International Nuclear Information System (INIS)

Akimoto, Hajime; Sobajima, Makoto; Abe, Yutaka; Iwamura, Takamichi; Ohnuki, Akira; Okubo, Tsutomu; Murao, Yoshio; Okabe, Kazuharu; Adachi, Hiromichi.

1990-07-01

In order to study the reflood behavior with low initial clad temperature, a reflood test was performed using the Slab Core Test Facility (SCTF) with initial clad temperature of 573 K. The test conditions of the test are identical with those of SCTF base case test S2-SH1 (initial clad temperature 1073 K) except the initial clad temperature. Through the comparison of results from these two tests, the following conclusions were obtained. (1) The low initial clad temperature resulted in the low differential pressures through the primary loops due to smaller steam generation in the core. (2) The low initial clad temperature caused the accumulated mass in the core to be increased and the accumulated mass in the downcomer to be decreased in the period of the lower plenum injection with accumulator (before 50s). In the later period of the cold leg injection with LPCI (after 100s), the water accumulation rates in the core and the downcomer were almost the same between both tests. (3) The low initial clad temperature resulted in the increase of the core inlet mass flow rate in the lower plenum injection period. However, the core inlet mass flow rate was almost the same regardless of the initial clad temperature in the later period of the cold leg injection period. (4) The low initial clad temperature resulted in the low turnaround temperature, high temperature rise and fast bottom quench front propagation. (5) In the region apart from the quench front, low initial clad temperature resulted in the lower heat transfer. In the region near the quench front, almost the same heat transfer coefficient was observed between both tests. (6) No flow oscillation with a long period was observed in the SCTF test with low initial clad temperature of 573 K, while it was remarkable in the Cylindrical Core Test Facility (CCTF) test which was performed with the same initial clad temperature. (J.P.N.)

Process for making unsaturated hydrocarbons using microchannel process technology

Science.gov (United States)

Tonkovich, Anna Lee [Dublin, OH; Yuschak, Thomas [Lewis Center, OH; LaPlante, Timothy J [Columbus, OH; Rankin, Scott [Columbus, OH; Perry, Steven T [Galloway, OH; Fitzgerald, Sean Patrick [Columbus, OH; Simmons, Wayne W [Dublin, OH; Mazanec, Terry Daymo, Eric

2011-04-12

The disclosed invention relates to a process for converting a feed composition comprising one or more hydrocarbons to a product comprising one or more unsaturated hydrocarbons, the process comprising: flowing the feed composition and steam in contact with each other in a microchannel reactor at a temperature in the range from about 200.degree. C. to about 1200.degree. C. to convert the feed composition to the product, the process being characterized by the absence of catalyst for converting the one or more hydrocarbons to one or more unsaturated hydrocarbons. Hydrogen and/or oxygen may be combined with the feed composition and steam.

Russian-Iranian relations in the Caspian Region: results and prospects

Directory of Open Access Journals (Sweden)

Sergey Sergeevich Zhiltcov

2016-12-01

relations with its neighbors but was not approved by Iran. Russian-Iranian relations were influenced by a profound effect of some western states, that imposed sanctions against Iran. Moreover, the fact that Iran was neglected when the export hydrocarbons routes were discussed and realized let new Caspian countries strengthen its positions. At the turn of 2015-2016 уears Russian-Iranian relations are on the rise, because of bilateral interest in solving regional issues and developing trade and credit agreements. Prospects of Russian-Iranian further cooperation will be determined by some key factors. There are Iranian energy policy, results of further multilateral negotiations on legal status of the Caspian Sea and the level of hydrocarbons production in “new” Caspian countries, that can strongly influence their international policies. All these factors will affect the further Russian-Iranian relations, because these two countries remain core players in the Caspian region.

Factors affecting elimination of polycyclic aromatic hydrocarbons from traditional smoked common carp meat

Science.gov (United States)

Babić, J.; Vidaković, S.; Škaljac, S.; Kartalović, B.; Ljubojević, D.; Ćirković, M.; Teodorović, V.

2017-09-01

Smoking techniques have been progressively improved and different procedures have been developed in different regions for treating fish. In these times, the technology is mainly used for enrichment of fish with specific taste and odour, to extend the shelf-life of these perishable products and appearance required widely on the market. A lot of chemical contaminants such as polycyclic aromatic hydrocarbons (PAHs) are formed during the combustion of fuel in the smoking process. PAHs are a group of compounds that have been the subject of great concern in the recent years due to their toxic, mutagenic and/or carcinogenic potentials to humans. These fact can have a significant impact on the acceptance of these products by consumers. In this review article, the objective is to describe factors affecting elimination of polycyclic aromatic hydrocarbons from traditional smoked common carp meat.

Distributions of polycyclic aromatic hydrocarbons and alkylated polycyclic aromatic hydrocarbons in Osaka Bay, Japan.

Science.gov (United States)

Miki, Shizuho; Uno, Seiichi; Ito, Kazuki; Koyama, Jiro; Tanaka, Hiroyuki

2014-08-30

Contaminations in sediments by polycyclic aromatic hydrocarbons (PAHs) and alkylated PAHs were investigated at 44 sites in Osaka Bay, Japan. Concentrations of total PAHs and alkylated PAHs were in the range 6.40-7800 ng/g dry weights and 13.7-1700 ng/g dry weights, respectively. The PAH concentrations tended to be higher along the shoreline in the vicinities of big ports, industrialized areas, and densely populated regions such as the cities of Osaka and Kobe. The major sources appeared to be pyrogenic or both pyrogenic and petrogenic at most of the sites. PAH concentrations were remarkably high at a site near Kobe, where the concentrations of dibenzo(a,h)anthracene and benzo(g,h,i)perylene exceeded the effects-range-medium concentration and eight PAHs were above the corresponding effects-range-low concentrations. Those PAHs may have been derived from the great fire associated with the large earthquake in 1995. Copyright © 2014 Elsevier Ltd. All rights reserved.

Identification and Characterisation of Major Hydrocarbons in ...

African Journals Online (AJOL)

Identification and Characterisation of Major Hydrocarbons in Thermally Degraded Low Density Polyethylene Films. ... There were alkanes, alkenes, halogenated alkanes, and very few aromatics in the liquid product and, the hydrocarbons were observed to range between C10 - C27. The FTIR and GC-MS results show the ...

DNA-based and culture-based characterization of a hydrocarbon-degrading consortium enriched from Arctic soil

Energy Technology Data Exchange (ETDEWEB)

Thomassin-Lacroix, E. J. M.; Reimer, K. J. [Royal Military College, Dept. of Chemistry and Chemical Engineering, Kingston, On (Canada); Yu, Z.; Mohn, W. W. [British Columbia Univ., Dept. of Microbiology and Immunology, Vancouver, BC (Canada); Eriksson, M. [Royal Inst. of Technology, Dept. of Biotechnology, Stockholm (Sweden)

2001-12-01

Oil spills are fairly common in polar tundra regions, including remote locations, and are a threat to the relatively fragile ecosystem. Remediation must be done economically and with minimum additional damage. Bioremediation is considered to be the appropriate technology, although its application in polar tundra regions is not well documented. Most studies of hydrocarbon remediation in polar regions have concerned marine oil spills, while a few studies have demonstrated on-site polar tundra soil remediation. A few of these demonstrated the presence of psychrotolerant hydrocarbon-degrading bacteria in polar tundra soils. Because fuels are complex mixtures of hydrocarbons, microbial consortia rather than pure cultures may be the most effective agents in degrading fuels. Despite their potential advantages for bioaugmentation applications, consortia are difficult to characterize and monitor. Molecular methods based on DNA analysis partially address these difficulties. One such approach is to randomly clone rRNA gene (rDNA) fragments and to sequence as a set of clones. The relative abundance of individual sequences in the clone library is related to the relative abundance of the corresponding organism in the community. In this study a psychrotolerant, fuel-degrading consortium was enriched with Arctic tundra soil. The enrichment substrate for the consortium was Jet A-1 fuel, which is very similar to Arctic diesel fuel, a common contaminant in the region. The objectives of the study were to (1) characterize thr consortium by DNA- and culture-based methods, (2) develop quantitative polymerase chain reaction assays for populations of predominant consortium members, and (3) determine the dynamics of those populations during incubation of the consortium. Result showed that is possible to quantitatively monitor members of a microbial consortium, with potential application for bioremediation of Arctic tundra soil. The relative abundance of consortium members was found to vary

Evaluation of environmental samples containing heavy hydrocarbon components in environmental forensic investigations

Energy Technology Data Exchange (ETDEWEB)

Raia, J.C.; Blakley, C.R.; Fuex, A.N.; Villalanti, D.C.; Fahrenthold, P.D. [Triton Anal Corp, Houston, TX (United States)

2004-03-01

This article presents a procedure to evaluate and characterize environmental samples containing mixtures of hydrocarbons over a wide boiling range of materials that include fuels and other products used in commerce. The range of the method extends to the higher boiling and heavier molecular weight hydrocarbon products in the range of motor oil, bunker fuel, and heavier residue materials. The procedure uses the analytical laboratory technique of high-temperature simulated distillation along with mathematical regression of the analytical data to estimate the relative contribution of individual products in mixtures of hydrocarbons present in environmental samples. An analytical technique to determine hydrocarbon-type distributions by gas chromatography-mass spectrometry with nitric oxide ionization spectrometry evaluation is also presented. This type of analysis allows complex hydrocarbon mixtures to be classified by their chemical composition, or types of hydrocarbons that include paraffins, cycloparaffins, monoaromatics, and polycyclic aromatic hydrocarbons. Characteristic hydrocarbon patterns for example, in the relative distribution of polycyclic aromatic hydrocarbons are valuable for determining the potential origin of materials present in environmental samples. These methods provide quantitative data for hydrocarbon components in mixtures as a function of boiling range and 'hydrocarbon fingerprints' of the types of materials present. This information is valuable in assessing environmental impacts of hydrocarbons at contaminated sites and establishing the liabilities and cost allocations for responsible parties.

Characteristics of Misclassified CT Perfusion Ischemic Core in Patients with Acute Ischemic Stroke.

Directory of Open Access Journals (Sweden)

Ralph R E G Geuskens

Full Text Available CT perfusion (CTP is used to estimate the extent of ischemic core and penumbra in patients with acute ischemic stroke. CTP reliability, however, is limited. This study aims to identify regions misclassified as ischemic core on CTP, using infarct on follow-up noncontrast CT. We aim to assess differences in volumetric and perfusion characteristics in these regions compared to areas that ended up as infarct on follow-up.This study included 35 patients with >100 mm brain coverage CTP. CTP processing was performed using Philips software (IntelliSpace 7.0. Final infarct was automatically segmented on follow-up noncontrast CT and used as reference. CTP and follow-up noncontrast CT image data were registered. This allowed classification of ischemic lesion agreement (core on CTP: rMTT≥145%, aCBV<2.0 ml/100g and infarct on follow-up noncontrast CT and misclassified ischemic core (core on CTP, not identified on follow-up noncontrast CT regions. False discovery ratio (FDR, defined as misclassified ischemic core volume divided by total CTP ischemic core volume, was calculated. Absolute and relative CTP parameters (CBV, CBF, and MTT were calculated for both misclassified CTP ischemic core and ischemic lesion agreement regions and compared using paired rank-sum tests.Median total CTP ischemic core volume was 49.7ml (IQR:29.9ml-132ml; median misclassified ischemic core volume was 30.4ml (IQR:20.9ml-77.0ml. Median FDR between patients was 62% (IQR:49%-80%. Median relative mean transit time was 243% (IQR:198%-289% and 342% (IQR:249%-432% for misclassified and ischemic lesion agreement regions, respectively. Median absolute cerebral blood volume was 1.59 (IQR:1.43-1.79 ml/100g (P<0.01 and 1.38 (IQR:1.15-1.49 ml/100g (P<0.01 for misclassified ischemic core and ischemic lesion agreement, respectively. All CTP parameter values differed significantly.For all patients a considerable region of the CTP ischemic core is misclassified. CTP parameters significantly

Biofilm comprising phototrophic, diazotrophic, and hydrocarbon-utilizing bacteria: a promising consortium in the bioremediation of aquatic hydrocarbon pollutants.

Science.gov (United States)

Al-Bader, Dhia; Kansour, Mayada K; Rayan, Rehab; Radwan, Samir S

2013-05-01

Biofilms harboring simultaneously anoxygenic and oxygenic phototrophic bacteria, diazotrophic bacteria, and hydrocarbon-utilizing bacteria were established on glass slides suspended in pristine and oily seawater. Via denaturing gradient gel electrophoresis analysis on PCR-amplified rRNA gene sequence fragments from the extracted DNA from biofilms, followed by band amplification, biofilm composition was determined. The biofilms contained anoxygenic phototrophs belonging to alphaproteobacteria; pico- and filamentous cyanobacteria (oxygenic phototrophs); two species of the diazotroph Azospirillum; and two hydrocarbon-utilizing gammaproteobacterial genera, Cycloclasticus and Oleibacter. The coexistence of all these microbial taxa with different physiologies in the biofilm makes the whole community nutritionally self-sufficient and adequately aerated, a condition quite suitable for the microbial biodegradation of aquatic pollutant hydrocarbons.

Microbial consortia involved in the anaerobic degradation of hydrocarbons.

Science.gov (United States)

Zwolinski; Harris, R F; Hickey, W J

2000-01-01

In this review, we examine the energetics of well-characterized biodegradation pathways and explore the possibilities for these to support growth of multiple organisms interacting in consortia. The relevant phenotypic and/or phylogenetic characteristics of isolates and consortia mediating hydrocarbon degradation coupled with different terminal electron-accepting processes (TEAP) are also reviewed. While the information on metabolic pathways has been gained from the analysis of individual isolates, the energetic framework presented here demonstrates that microbial consortia could be readily postulated for hydrocarbon degradation coupled to any TEAP. Several specialized reactions occur within these pathways, and the organisms mediating these are likely to play a key role in defining the hydrocarbon degradation characteristics of the community under a given TEAP. Comparing these processes within and between TEAPs reveals biological unity in that divergent phylotypes display similar degradation mechanisms and biological diversity in that hydrocarbon-degraders closely related as phylotypes differ in the type and variety of hydrocarbon degradation pathways they possess. Analysis of microcosms and of field samples suggests that we have only begun to reveal the diversity of organisms mediating anaerobic hydrocarbon degradation. Advancements in the understanding of how hydrocarbon-degrading communities function will be significantly affected by the extent to which organisms mediating specialized reactions can be identified, and tools developed to allow their study in situ.