WorldWideScience

Sample records for hydraulic conductivity electronic

  1. Hydraulic conductivity of organomodified soil

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, R.B.; Grant, J.M.; Voice, T.C.; Rakhshandehroo, G.; Xu, S.; Boyd, S.A. [Michigan State Univ., East Lansing, MI (United States)

    1995-11-01

    The effects of organomodification on soil hydraulic conductivity were investigated. Hydraulic conductivity and porosity of treated and untreated samples of a sandy loam were measured as a function of effective stress. Batch treatment with hexadecyltrimethyl ammonium (HDTMA) and dry packing produced organomodified samples that were 79% less conducive than untreated samples prior to loading. Treated samples lost less hydraulic conductivity as a result of loading than untreated samples so that treated samples had higher conductivity at high loads. Observed differences in conductivity are explained in terms of the role of the treated and untreated clay in controlling initial effective pore size and its change during consolidation.

  2. Hydraulic conductivity of compacted zeolites.

    Science.gov (United States)

    Oren, A Hakan; Ozdamar, Tuğçe

    2013-06-01

    Hydraulic conductivities of compacted zeolites were investigated as a function of compaction water content and zeolite particle size. Initially, the compaction characteristics of zeolites were determined. The compaction test results showed that maximum dry unit weight (γ(dmax)) of fine zeolite was greater than that of granular zeolites. The γ(dmax) of compacted zeolites was between 1.01 and 1.17 Mg m(-3) and optimum water content (w(opt)) was between 38% and 53%. Regardless of zeolite particle size, compacted zeolites had low γ(dmax) and high w(opt) when compared with compacted natural soils. Then, hydraulic conductivity tests were run on compacted zeolites. The hydraulic conductivity values were within the range of 2.0 × 10(-3) cm s(-1) to 1.1 × 10(-7) cm s(-1). Hydraulic conductivity of all compacted zeolites decreased almost 50 times as the water content increased. It is noteworthy that hydraulic conductivity of compacted zeolite was strongly dependent on the zeolite particle size. The hydraulic conductivity decreased almost three orders of magnitude up to 39% fine content; then, it remained almost unchanged beyond 39%. Only one report was found in the literature on the hydraulic conductivity of compacted zeolite, which is in agreement with the findings of this study.

  3. Hydraulic conductivity of GCLs in MSW landfills

    Institute of Scientific and Technical Information of China (English)

    LI Guo-cheng; YANG Wu-chao; DAN Tang-hui

    2008-01-01

    The state of the art of the study on the hydraulic conductivity of GCLs is presented in terms of the in-fluence of the effective stress, chemical interactions, freeze - thaw cycles and temperature gradients. The chan-ges of void ratio caused by changes of effective stress have a direct linear effect on the hydraulic conductivity, regardless of the cation concentration or the thickness of the adsorbed layer. The hydraulic conductivity is relat-ed to the relative abundance of monovalent and divalent cation(RMD), and RMD has a great effect on the hy-draulic conductivity in weak solution. The long-term susceptibility of GCLs to increased hydraulic conductivity as a response to repeated freeze-thaw cycling is minimal, which has been proved after 150 freeze-thaw cycles. The potential of desiccation cracking increases with the increasing temperature gradient and is related to the ini-tial subsoil water content, the applied overburden stress, etc.

  4. Soil Structure and Saturated Hydraulic Conductivity

    Science.gov (United States)

    Houskova, B.; Nagy, V.

    The role of soil structure on saturated hydraulic conductivity changes is studied in plough layers of texturally different soils. Three localities in western part of Slovakia in Zitny ostrov (Corn Island) were under investigation: locality Kalinkovo with light Calcaric Fluvisol (FAO 1970), Macov with medium heavy Calcari-mollic Fluvisol and Jurova with heavy Calcari-mollic Fluvisol. Soil structure was determined in dry as well as wet state and in size of macro and micro aggregates. Saturated hydraulic conductivity was measured by the help of double ring method. During the period of ring filling the soil surface was protected against aggregates damage by falling water drops. Spatial and temporal variability of studied parameters was evaluated. Cultivated crops were ensilage maize at medium heavy and heavy soil and colza at light soil. Textural composition of soil and actual water content at the beginning of measurement are one of major factor affecting aggregate stability and consequently also saturated hydraulic conductivity.

  5. Hydraulic Conductivity Anisotropy of Heterogeneous Unsaturated Soils

    Science.gov (United States)

    Sun, Dongmin; Zhu, Jianting

    2010-05-01

    The effects of saturation degree (or capillary pressure) on hydraulic conductivity anisotropy in unsaturated soils have not been fully understood. This study developed an approach based on a conceptualization of combining the neural network based pedo-transfer function (PTF) results with the thin layer concept to explore the capillary pressure-dependent anisotropy in relation to soil texture and soil bulk density. The main objective is to examine how anisotropy characteristics are related to the relationships between hydraulic parameters and the basic soil attributes such as texture and bulk density. The hydraulic parameters are correlated with the texture and bulk density based on the pedo-transfer function (PTF) results. It is demonstrated that non-monotonic behavior of the unsaturated soil anisotropy in relation to the capillary pressure is only observed when the saturated hydraulic conductivity and the shape parameter are both related to the mean particle diameter. When only one hydraulic parameter is related to the grain diameter or when both are not related to the same attribute simultaneously, the unsaturated soil anisotropy increases monotonically with the increasing capillary pressure head. Therefore, it is suggested that this behavior is mainly due to the coupled dependence of the layer saturated hydraulic conductivities and the shape factors on the texture and bulk density. The correlation between the soil grain diameter and bulk density decreases the anisotropy effects of the unsaturated layered soils. The study illustrates that the inter-relationships of soil texture, bulk density, and hydraulic properties may cause vastly different characteristics of anisotropic unsaturated soils.

  6. Measurement and modeling of unsaturated hydraulic conductivity

    Science.gov (United States)

    Perkins, Kim S.; Elango, Lakshmanan

    2011-01-01

    The unsaturated zone plays an extremely important hydrologic role that influences water quality and quantity, ecosystem function and health, the connection between atmospheric and terrestrial processes, nutrient cycling, soil development, and natural hazards such as flooding and landslides. Unsaturated hydraulic conductivity is one of the main properties considered to govern flow; however it is very difficult to measure accurately. Knowledge of the highly nonlinear relationship between unsaturated hydraulic conductivity (K) and volumetric water content is required for widely-used models of water flow and solute transport processes in the unsaturated zone. Measurement of unsaturated hydraulic conductivity of sediments is costly and time consuming, therefore use of models that estimate this property from more easily measured bulk-physical properties is common. In hydrologic studies, calculations based on property-transfer models informed by hydraulic property databases are often used in lieu of measured data from the site of interest. Reliance on database-informed predicted values with the use of neural networks has become increasingly common. Hydraulic properties predicted using databases may be adequate in some applications, but not others. This chapter will discuss, by way of examples, various techniques used to measure and model hydraulic conductivity as a function of water content, K. The parameters that describe the K curve obtained by different methods are used directly in Richards’ equation-based numerical models, which have some degree of sensitivity to those parameters. This chapter will explore the complications of using laboratory measured or estimated properties for field scale investigations to shed light on how adequately the processes are represented. Additionally, some more recent concepts for representing unsaturated-zone flow processes will be discussed.

  7. HYDRAULIC CONDUCTIVITY OF THREE GEOSYNTHETIC CLAY LINERS

    Science.gov (United States)

    The hydraulic conductivity of three 2.9 m2 (32 sq ft) geosynthetic clay liners (GCLs) was measured. Tests were performed on individual sheets of the GCLs, on overlapped pieces of GCLs, and on composite liners consisting of a punctured geomembrane overlying a GCL. Hyd...

  8. Dentin permeability: determinants of hydraulic conductance.

    Science.gov (United States)

    Reeder, O W; Walton, R E; Livingston, M J; Pashley, D H

    1978-02-01

    A technique is described which permits measurements of the ease with which fluid permeates dentin. This value, the hydraulic conductance of dentin, increased as surface area increases and/or as dentin thickness decreases. It increased 32-fold when dentin was acid etched due to removal of surface debris occluding the tubules.

  9. Hydraulic conductivity and diffusion characterization of GCLs

    Energy Technology Data Exchange (ETDEWEB)

    Mukunoki, T.; Rowe, R.K.; Li, H.M.; Sangam, H.P.; Hurst, P.; Bathurst, R.J. [Queen' s Univ., Kingston, ON (Canada)]|[Royal Military Coll. of Canada, Kingston, ON (Canada); Badv, K. [Urmia Univ. (Iran, Islamic Republic of)

    2003-07-01

    This paper reports on the characterization of the hydraulic conductivity and diffusion of a geosynthetic clay liner (GCL) installed at a site off the southeast coast of Baffin Island, in the Canadian Arctic, following different levels of freeze-thaw exposure and under low temperature conditions. The authors presented a summary of the results obtained for hydraulic conductivity tests on GCLs subjected to freeze-thaw cycles, and specimens permeated with jet fuel (Arctic diesel). They also reported on diffusion tests conducted at 22 Celsius and 5 Celsius, followed by a discussion of the effect of temperature. The results indicate that there is no significant impact on GCL performance due to freeze-thaw cycles, permeation by jet fuel or diffusion at the lower temperatures expected in the north for the short term (up to approximately four years). Additional studies are needed to confirm long term behaviour. 24 refs., 2 tabs., 4 figs.

  10. Geostatistical Estimations of Regional Hydraulic Conductivity Fields

    Science.gov (United States)

    Patriarche, D.; Castro, M. C.; Goovaerts, P.

    2004-12-01

    Direct and indirect measurements of hydraulic conductivity (K) are commonly performed, providing information on the magnitude of this parameter at the local scale (tens of centimeters to hundreds of meters) and at shallow depths. By contrast, field information on hydraulic conductivities at regional scales of tens to hundreds of kilometers and at greater depths is relatively scarce. Geostatistical methods allow for sparsely sampled observations of a variable (primary information) to be complemented by a more densely sampled secondary attribute. Geostatistical estimations of the hydraulic conductivity field in the Carrizo aquifer, a major groundwater flow system extending along Texas, are performed using available primary (e.g., transmissivity, hydraulic conductivity) and secondary (specific capacity) information, for depths up to 2.2 km, and over three regional domains of increasing extent: 1) the domain corresponding to a three-dimensional groundwater flow model previously built (model domain); 2) the area corresponding to the ten counties encompassing the model domain (County domain), and; 3) the full extension of the Carrizo aquifer within Texas (Texas domain). Two different approaches are used: 1) an indirect approach are transmissivity (T) is estimated first and (K) is retrieved through division of the T estimate by the screening length of the wells, and; 2) a direct approach where K data are kriged directly. Prediction performances of the tested geostatistical procedures (kriging combined with linear regression, kriging with known local means, kriging of residuals, and cokriging) are evaluated through cross validation for both log-transformed variables and back-transformed ones. For the indirect approach, kriging of log T residuals yields the best estimates for both log-transformed and back-transformed variables in the model domain. For larger regional scales (County and Texas domains), cokriging performs generally better than univariate kriging procedures

  11. Comparison of four methods to assess hydraulic conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Benson, C.H. [Univ. of Wisconsin, Madison, WI (United States). Dept. of Civil and Environmental Engineering; Gunter, J.A. [Gunter (John A.), Round Rock, TX (United States); Boutwell, G.P. [STE, Inc., Baton Rouge, LA (United States); Trautwein, S.J. [Trautwein Soil Testing Equipment Co., Houston, TX (United States); Berzanskis, P.H. [Hoechst-Celanese, Inc., Pampa, TX (United States)

    1997-10-01

    A hydraulic conductivity assessment that was conducted on four test pads constructed to the same specifications with soil from the same source by four different contractors is described. The test pads had distinctly different field hydraulic conductivities, even though they were constructed with similar soil, to similar compaction conditions, and with similar machinery. Adequate hydration time was key in achieving low field hydraulic conductivity. More extensive processing was another factor responsible for low field hydraulic conductivity. Four different test methods were used to assess the hydraulic conductivity of each test pad: (1) sealed double-ring infiltrometers (SDRIs); (2) two-stage borehole permeameters; (3) laboratory hydraulic conductivity tests on large block specimens; and (4) laboratory hydraulic conductivity tests on small specimens collected in thin-wall sampling tubes. The tests were conducted independently by each of the writers. After the tests were completed, the results were submitted and compared. Analysis of the test results show that the three large-scale test methods generally yield similar hydraulic conductivities. For two of the test pads, however, the hydraulic conductivities of the specimens collected in sampling tubes were significantly lower than the field hydraulic conductivities. Both of these test pads had high field hydraulic conductivity. Thus, there is little value in using small specimens to assess field hydraulic conductivity.

  12. Formed Core Sampler Hydraulic Conductivity Testing

    Energy Technology Data Exchange (ETDEWEB)

    Miller, D. H.; Reigel, M. M.

    2012-09-25

    A full-scale formed core sampler was designed and functionally tested for use in the Saltstone Disposal Facility (SDF). Savannah River National Laboratory (SRNL) was requested to compare properties of the formed core samples and core drilled samples taken from adjacent areas in the full-scale sampler. While several physical properties were evaluated, the primary property of interest was hydraulic conductivity. Differences in hydraulic conductivity between the samples from the formed core sampler and those representing the bulk material were noted with respect to the initial handling and storage of the samples. Due to testing conditions, the site port samples were exposed to uncontrolled temperature and humidity conditions prior to testing whereas the formed core samples were kept in sealed containers with minimal exposure to an uncontrolled environment prior to testing. Based on the results of the testing, no significant differences in porosity or density were found between the formed core samples and those representing the bulk material in the test stand.

  13. A tensor approach to the estimation of hydraulic conductivities in ...

    African Journals Online (AJOL)

    2006-07-03

    Jul 3, 2006 ... The HC values computed from the data measured on the weathered or ... Keywords: hydraulic conductivity tensor, roughness, combined stress, hydraulic aperture, Table Mountain ... the anisotropic nature of studied media.

  14. Variation in reach-scale hydraulic conductivity of streambeds

    Science.gov (United States)

    Stewardson, M. J.; Datry, T.; Lamouroux, N.; Pella, H.; Thommeret, N.; Valette, L.; Grant, S. B.

    2016-04-01

    Streambed hydraulic conductivity is an important control on flow within the hyporheic zone, affecting hydrological, ecological, and biogeochemical processes essential to river ecosystem function. Despite many published field measurements, few empirical studies examine the drivers of spatial and temporal variations in streambed hydraulic conductivity. Reach-averaged hydraulic conductivity estimated for 119 surveys in 83 stream reaches across continental France, even of coarse bed streams, are shown to be characteristic of sand and finer sediments. This supports a model where processes leading to the accumulation of finer sediments within streambeds largely control hydraulic conductivity rather than the size of the coarse bed sediment fraction. After describing a conceptual model of relevant processes, we fit an empirical model relating hydraulic conductivity to candidate geomorphic and hydraulic drivers. The fitted model explains 72% of the deviance in hydraulic conductivity (and 30% using an external cross-validation). Reach hydraulic conductivity increases with the amplitude of bedforms within the reach, the bankfull channel width-depth ratio, stream power and upstream catchment erodibility but reduces with time since the last streambed disturbance. The correlation between hydraulic conductivity and time since a streambed mobilisation event is likely a consequence of clogging processes. Streams with a predominantly suspended load and less frequent streambed disturbances are expected to have a lower streambed hydraulic conductivity and reduced hyporheic fluxes. This study suggests a close link between streambed sediment transport dynamics and connectivity between surface water and the hyporheic zone.

  15. Soil hydraulic properties near saturation, an improved conductivity model

    DEFF Research Database (Denmark)

    Børgesen, Christen Duus; Jacobsen, Ole Hørbye; Hansen, Søren;

    2006-01-01

    The hydraulic properties near saturation can change dramatically due to the presence of macropores that are usually difficult to handle in traditional pore size models. The purpose of this study is to establish a data set on hydraulic conductivity near saturation, test the predictive capability...... of commonly used hydraulic conductivity models and give suggestions for improved models. Water retention and near saturated and saturated hydraulic conductivity were measured for a variety of 81 top and subsoils. The hydraulic conductivity models by van Genuchten [van Genuchten, 1980. A closed-form equation...... for predicting the hydraulic conductivity of unsaturated soils. Soil Sci. Soc. Am. J. 44, 892–898.] (vGM) and Brooks and Corey, modified by Jarvis [Jarvis, 1991. MACRO—A Model of Water Movement and Solute Transport in Macroporous Soils. Swedish University of Agricultural Sciences. Department of Soil Sciences...

  16. Determining the Porosity and Saturated Hydraulic Conductivity of Binary Mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Z. F.; Ward, Anderson L.; Keller, Jason M.

    2009-09-27

    Gravels and coarse sands make up significant portions of some environmentally important sediments, while the hydraulic properties of the sediments are typically obtained in the laboratory using only the fine fraction (e.g., <2 mm or 4.75 mm). Researchers have found that the content of gravel has significant impacts on the hydraulic properties of the bulk soils. Laboratory experiments were conducted to measure the porosity and the saturated hydraulic conductivity of binary mixtures with different fractions of coarse and fine components. We proposed a mixing-coefficient model to estimate the porosity and a power-averaging method to determine the effective particle diameter and further to predict the saturated hydraulic conductivity of binary mixtures. The proposed methods could well estimate the porosity and saturated hydraulic conductivity of the binary mixtures for the full range of gravel contents and was successfully applied to two data sets in the literature.

  17. Hydraulic conductivity of a firn aquifer system in southeast Greenland

    Science.gov (United States)

    Miller, Olivia L.; Solomon, D. Kip; Miège, Clément; Koenig, Lora S.; Forster, Richard R.; Montgomery, Lynn N.; Schmerr, Nicholas; Ligtenberg, Stefan R. M.; Legchenko, Anatoly; Brucker, Ludovic

    2017-05-01

    Some regions of the Greenland ice sheet, where snow accumulation and melt rates are high, currently retain substantial volumes of liquid water within the firn pore space throughout the year. These firn aquifers, found between 10-30 m below the snow surface, may significantly affect sea level rise by storing or draining surface meltwater. The hydraulic gradient and the hydraulic conductivity control flow of meltwater through the firn. Here we describe the hydraulic conductivity of the firn aquifer estimated from slug tests and aquifer tests at six sites located upstream of Helheim Glacier in southeastern Greenland. We conducted slug tests using a novel instrument, a piezometer with a heated tip that melts itself into the ice sheet. Hydraulic conductivity ranges between 2.5x10-5 and 1.1x10-3 m/s. The geometric mean of hydraulic conductivity of the aquifer is 2.7x10-4 m/s with a geometric standard deviation of 1.4 from both depth specific slug tests (analyzed using the Hvorslev method) and aquifer tests during the recovery period. Hydraulic conductivity is relatively consistent between boreholes and only decreases slightly with depth. The hydraulic conductivity of the firn aquifer is crucial for determining flow rates and patterns within the aquifer, which inform hydrologic models of the aquifer, its relation to the broader glacial hydrologic system, and its effect on sea level rise.

  18. Hydraulic Conductivity of a Firn Aquifer in Southeast Greenland

    Directory of Open Access Journals (Sweden)

    Olivia L. Miller

    2017-05-01

    Full Text Available Some regions of the Greenland ice sheet, where snow accumulation and melt rates are high, currently retain substantial volumes of liquid water within the firn pore space throughout the year. These firn aquifers, found between ~10 and 30 m below the snow surface, may significantly affect sea level rise by storing or draining surface meltwater. The hydraulic gradient and the hydraulic conductivity control flow of meltwater through the firn. Here we describe the hydraulic conductivity of the firn aquifer estimated from slug tests and aquifer tests at six sites located upstream of Helheim Glacier in southeastern Greenland. We conducted slug tests using a novel instrument, a piezometer with a heated tip that melts itself into the ice sheet. Hydraulic conductivity ranges between 2.5 × 10−5 and 1.1 × 10−3 m/s. The geometric mean of hydraulic conductivity of the aquifer is 2.7 × 10−4 m/s with a geometric standard deviation of 1.4 from both depth specific slug tests (analyzed using the Hvorslev method and aquifer tests during the recovery period. Hydraulic conductivity is relatively consistent between boreholes and only decreases slightly with depth. The hydraulic conductivity of the firn aquifer is crucial for determining flow rates and patterns within the aquifer, which inform hydrologic models of the aquifer, its relation to the broader glacial hydrologic system, and its effect on sea level rise.

  19. Hydraulic Conductivity of Compacted Laterite Treated with Iron Ore Tailings

    Directory of Open Access Journals (Sweden)

    Umar Sa’eed Yusuf

    2016-01-01

    Full Text Available The objective of this study was to investigate the effect of iron ore tailings (IOT on hydraulic conductivity of compacted laterite. The IOT conforms to ASTM C 618-15 Type F designations. In the present study, soil was admixed with 0–20% IOT and compacted at moulding water content ranging from 10 to 25% using four types of compactive efforts. Hydraulic conductivities of the compacted soil-IOT mixtures were determined using deionized water and municipal solid waste leachate as the permeant fluids, respectively. Deionized water was the reference permeant fluid. Results of this study showed that hydraulic conductivity decreased with increase in IOT content as a result of improvement in mechanical properties of the soil. Permeation of the soil-IOT mixtures with leachate caused the hydraulic conductivity to drop to less than 1 × 10−9 m/s especially at higher compactive efforts. Also, bioclogging of the soil pores due to accumulation of biomass from bacteria and yeast present in the leachate tends to significantly reduce the hydraulic conductivity. From an economic point of view, it has been found from the results of this study that soil specimens treated with up to 20% IOT and compacted at the British Standard Light (BSL compactive effort met the maximum regulatory hydraulic conductivity of less than or equal to 1 × 10−9 m/s for hydraulic barrier system.

  20. Xylem hydraulic conductivity related to conduit dimensions along chrysanthemum stems.

    NARCIS (Netherlands)

    Nijsse, J.; Heijden, van der G.W.A.M.; Ieperen, van W.; Keijzer, C.J.; Meeteren, van U.

    2001-01-01

    The stem xylem conduit dimensions and hydraulic conductivity of chrysanthemum plants (Dendranthemaxgrandiflorum Tzvelev cv. Cassa) were analysed and quantified. Simple exponential relations describe conduit length distribution, height dependency of conduit length distribution, and height dependency

  1. Spatial variability in streambed hydraulic conductivity of contrasting stream morphologies

    DEFF Research Database (Denmark)

    Sebök, Éva; Calvache, Carlos Duque; Engesgaard, Peter Knudegaard;

    2015-01-01

    Streambed hydraulic conductivity is one of the main factors controlling variability in surface water-groundwater interactions, but only few studies aim at quantifying its spatial and temporal variability in different stream morphologies. Streambed horizontal hydraulic conductivities (Kh) were...... therefore determined from in-stream slug tests, vertical hydraulic conductivities (Kv) were calculated with in-stream permeameter tests and hydraulic heads were measured to obtain vertical head gradients at eight transects, each comprising five test locations, in a groundwater-dominated stream. Seasonal...... small-scale measurements were taken in December 2011 and August 2012, both in a straight stream channel with homogeneous elevation and downstream of a channel meander with heterogeneous elevation. All streambed attributes showed large spatial variability. Kh values were the highest at the depositional...

  2. Hydraulic Conductivity of Residual Soil-Cement Mix

    Science.gov (United States)

    Govindasamy, P.; Taha, M. R.

    2016-07-01

    In Malaysia, although there are several researches on engineering properties of residual soils, however study on the hydraulic conductivity properties of metasedimentary residual soils is still lacking. Construction of containment walls like slurry wall techniques can be achieved with hydraulic conductivity of approximately 5 x 10-7cm/sec. The objectives of the study were to determine the physical properties of metasedimentary residual soils and to determine the influence of 1%, 3%, 5% and 10% of cement on hydraulic conductivity parameters. The coefficient of hydraulic conductivity of the soil naturally and soil-cement mixtures were determined by using the falling head test. According to the test, the hydraulic conductivity of the original soil was 4.16 x 10-8 m/s. The value decreases to 3.89 x 10-8 m/s, 2.78 x 10-8 m/s then 6.83 x 10-9 m/s with the addition of 1%, 3% and 5% of cement additives, respectively. During the hydration process, cement hydrates is formed followed by the increase in pH value and Ca(OH)2 which will alter the modification of pores size and distribution. When the quantity of cement increases, the pores size decrease. But, the addition of 10% cement gives an increased hydraulic conductivity value to 2.78 x 10-8 m/s. With 10%, the pore size increase might due to flocculation and agglomeration reaction. The generated hydraulic conductivity values will indirectly become a guide in the preliminary soil cement stabilization to modify the properties of the soil to become more like the properties of a soft rock.1. Introduction

  3. HYDRAULIC CONDUCTIVITY OF GCL WITH BENTONITE – SILICA FUME MATRIX

    OpenAIRE

    M. Andal; Chandrasekhar, M.; G. K. Viswanadh

    2012-01-01

    This paper presents the influence of partial replacement of bentonite by silica fume which is used in the manufacture of Geosynthetic Clay Liner (GCL). Geosynthetic Clay Liners consist bentonite (Sodium Based) sandwiched between two geotextile. Benotinite, having low permeability imparts better hydraulic performance to the GCL to act as liner. In this investigation, an attempt has been made to study the hydraulic conductivity of GCL with modified Bentonite. The bentonite is partially replaced...

  4. Rapid shoot‐to‐root signalling regulates root hydraulic conductance via aquaporins

    National Research Council Canada - National Science Library

    VANDELEUR, REBECCA K; SULLIVAN, WENDY; ATHMAN, ASMINI; JORDANS, CHARLOTTE; GILLIHAM, MATTHEW; KAISER, BRENT N; TYERMAN, STEPHEN D

    2014-01-01

    Investigating the relationship between transpiration and root hydraulic conductance Vandeleur et al report that leaf area reduction reduces root hydraulic conductance in grapevine, soybean and maize...

  5. VARIABILITY OF HYDRAULIC CONDUCTIVITY DUE TO MULTIPLE FACTORS

    Directory of Open Access Journals (Sweden)

    Sanjit K. Deb

    2012-01-01

    Full Text Available Soil properties are greatly influenced by intrinsic factors of soil formation as well as extrinsic factors associated with land use and management and vary both in time and space. Intrinsic variability is caused by the pedogenesis and usually takes place at large time scales. The variability caused by extrinsic factors could take effect relatively quickly and could not be treated as regionalized. Saturated hydraulic conductivity is one of the most important soil properties for soil-water-plant interactions, water and contaminant movement and retention through the soil profile. It is a critically important parameter for estimation of various other soil hydrological parameters necessary for modeling flow through the naturally unsaturated vadose zone. Among different soil hydrological properties, saturated hydraulic conductivity is reported to have the greatest statistical variability, which is associated with soil types, land uses, positions on landscape, depths, instruments and methods of measurement and experimental errors. The variability of saturated hydraulic conductivity has a profound influence on the overall hydrology of the soil system. Therefore, focus of this review is centered on the variability of saturated/unsaturated hydraulic conductivity due to a large number of factors. This study reviews recent experimental and field studies addressing the measurements and variability of hydraulic conductivity. A synthesis of a large amount of data available in literature is presented and the possible sources of the variability and its implications are discussed. The variability of a soil hydraulic conductivity can be expressed by range, interquartile range, variance and standard deviation, coefficient of variation, skewness and kurtosis. The spatial and temporal variability of hydraulic conductivity and the influences of sample support, measurement devices/methods, soils, land uses and agricultural management on hydraulic conductivity are

  6. Changes in Root Hydraulic Conductivity During Wheat Evolution

    Institute of Scientific and Technical Information of China (English)

    Chang-Xing ZHAO; Xi-Ping DENG; Lun SHAN; Ernst STEUDLE; Sui-Qi ZHANG; Qing YE

    2005-01-01

    A better understanding of the mechanisms of water uptake by plant roots should be vital for improving drought resistance and water use efficiency (WUE). In the present study, we have demonstrated correlations between root system hydraulic conductivity and root characteristics during evolution using six wheat evolution genotypes (solution culture) with different ploidy chromosome sets (Triticum boeoticum Bioss., T. monococcum L.: 2n = 2x = 14; T. dicoccides Koern., T. dicoccon (Schrank) Schuebl.: 2n = 4x = 28;T. vulgare Vill., T. aestivum L. cv. Xiaoyan No. 6: 2n = 6x = 42). The experimental results showed that significant correlations were found between root system hydraulic conductivity and root characteristics of the materials with the increase in ploidy chromosomes (2x→6x) during wheat evolution. Hydraulic conductivity of the wheat root system at the whole-plant level was increased with chromosome ploidy during evolution, which was positively correlated with hydraulic conductivity of single roots, whole plant biomass,root average diameter, and root growth (length, area), whereas the root/shoot ratio had an inverse correlation with the hydraulic conductivity of root system with increasing chromosome ploidy during wheat evolution. Therefore, it is concluded that that the water uptake ability of wheat roots was strengthened from wild to modern cultivated species during evolution, which will provide scientific evidence for genetic breeding to improve the WUE of wheat by genetic engineering.

  7. Hydraulic conductivities of fractures and matrix in Slovenian carbonate aquifers

    Directory of Open Access Journals (Sweden)

    Timotej Verbovšek

    2008-12-01

    Full Text Available Hydraulic conductivities and specific storage coefficients of fractures and matrix in Slovenian carbonate aquifers were determined by Barker’s method for pumping test analysis, based on fractional flow dimension. Values are presented for limestones and mainly for dolomites, and additionally for separate aquifers, divided by age andlithology in several groups. Data was obtained from hydrogeological reports for 397 water wells, and among these, 79 pumping tests were reinterpreted. Hydraulic conductivities of fractures are higher than the hydraulic conductivities of matrix, and the differences are highly statistically significant. Likewise, differences are significant for specific storage, and the values of these coefficients are higher in the matrix. Values of all coefficients vary in separate aquifers, and the differences can be explained by diagenetic effects, crystal size, degree of fracturing, andcarbonate purity. Comparison of the methods, used in the reports, and the Barker’s method (being more suitable for karstic and fractured aquifers, shows that the latter fits real data better.

  8. Hydraulic conductivity of natural soils permeated with acid mine drainage

    Energy Technology Data Exchange (ETDEWEB)

    Yanful, E.K.; Shikatani, K.S.; Quirt, D.H. [University of Western Ontario, London, ON (Canada). Department of Civil Engineering

    1995-08-01

    The results of a laboratory study on the interactions of three natural soils (some under consideration as candidate cover materials) with acid mine drainage (AMD) are presented. Soil hydraulic conductivity measurements were used to assess soil compatibility with AMD. A silty clay from the decommissioned Waite Amulet tailings site in Quebec, glacial tills from the Heath Steele mine site in New Brunswick, and soil from the Faro mine site in the Yukon Territory were examined. Soil mineralogy and chemistry were examined before and after hydraulic conductivity testing to identify any changes. 20 refs., 25 figs., 8 tabs.

  9. Measurement and modeling of unsaturated hydraulic conductivity: Chapter 21

    Science.gov (United States)

    Perkins, Kim S.; Elango, Lakshmanan

    2011-01-01

    The unsaturated zone plays an extremely important hydrologic role that influences water quality and quantity, ecosystem function and health, the connection between atmospheric and terrestrial processes, nutrient cycling, soil development, and natural hazards such as flooding and landslides. Unsaturated hydraulic conductivity is one of the main properties considered to govern flow; however it is very difficult to measure accurately. Knowledge of the highly nonlinear relationship between unsaturated hydraulic conductivity (K) and volumetric water content () is required for widely-used models of water flow and solute transport processes in the unsaturated zone. Measurement of unsaturated hydraulic conductivity of sediments is costly and time consuming, therefore use of models that estimate this property from more easily measured bulk-physical properties is common. In hydrologic studies, calculations based on property-transfer models informed by hydraulic property databases are often used in lieu of measured data from the site of interest. Reliance on database-informed predicted values with the use of neural networks has become increasingly common. Hydraulic properties predicted using databases may be adequate in some applications, but not others.

  10. Measurement of soil hydraulic conductivity in relation with vegetation

    Science.gov (United States)

    Chen, Xi; Cheng, Qinbo

    2010-05-01

    Hydraulic conductivity is a key parameter which influences hydrological processes of infiltration, surface and subsurface runoff. Vegetation alters surface characteristics (e.g., surface roughness, litter absorption) or subsurface characteristics (e.g. hydraulic conductivity). Field infiltration experiment of a single ring permeameter is widely used for measuring soil hydraulic conductivity. Measurement equipment is a simple single-ring falling head permeameter which consists of a hollow cylinder that is simply inserted into the top soil. An optimization method on the basis of objective of minimum error between the measured and simulated water depths in the single-ring is developed for determination of the soil hydraulic parameters. Using the single ring permeameter, we measured saturated hydraulic conductivities (Ks) of the red loam soil with and without vegetation covers on five hillslopes at Taoyuan Agro-Ecology Experimental Station, Hunan Province of China. For the measurement plots without vegetation roots, Ks value of the soil at 25cm depth is much smaller than that of surface soil (1.52×10-4 vs. 1.10×10-5 m/s). For the measurement plots with vegetation cover, plant roots significantly increase Ks of the lower layer soil but this increase is not significant for the shallow soil. Moreover, influences of vegetation root on Ks depend on vegetation species and ages. Ks value of the Camellia is about three times larger than that of seeding of Camphor (2.62×10-4 vs. 9.82×10-5 m/s). Ks value of the matured Camellia is 2.72×10-4 m/s while Ks value of the young Camellia is only 2.17×10-4 m/s. Key words: single ring permeameter; soil hydraulic conductivity; vegetation

  11. EVALUATION OF HYDRAULIC CONDUCTIVITIES CALCULATED FROM MULTIPORT-PERMEAMETER MEASUREMENTS

    Science.gov (United States)

    A multiport permeameter was developed for use in estimating hydraulic conductivity over intact sections of aquifer core using the core liner as the permeameter body. Six cores obtained from one borehole through the upper 9 m of a stratified glacial-outwash aquifer were used to ev...

  12. Water Infiltration and Hydraulic Conductivity in Sandy Cambisols

    DEFF Research Database (Denmark)

    Bens, Oliver; Wahl, Niels Arne; Fischer, Holger

    2006-01-01

    Soil hydrological properties like infiltration capacity and hydraulic conductivity have important consequences for hydrological properties of soils in river catchments and for flood risk prevention. They are dynamic properties due to varying land use management practices. The objective of this st......Soil hydrological properties like infiltration capacity and hydraulic conductivity have important consequences for hydrological properties of soils in river catchments and for flood risk prevention. They are dynamic properties due to varying land use management practices. The objective...... of this study was to characterize the variation of infiltration capacity, hydraulic conductivity and soil organoprofile development on forest sites with comparable geological substrate, soil type and climatic conditions, but different stand ages and tree species in terms of the effects of forest transformation...... from pure Scots pine stands towards pure European beech stands. The water infiltration capacity and hydraulic conductivity (K) of the investigated sandy-textured soils are low and very few macropores exist. Additionally these pores are marked by poor connectivity and therefore do not have any...

  13. Verification of HYDRASTAR: Analysis of hydraulic conductivity fields and dispersion

    Energy Technology Data Exchange (ETDEWEB)

    Morris, S.T.; Cliffe, K.A. [AEA Technology, Harwell (United Kingdom)

    1994-10-01

    HYDRASTAR is a code for the stochastic simulation of groundwater flow. It can be used to simulate both time-dependent and steady-state groundwater flow at constant density. Realizations of the hydraulic conductivity field are generated using the Turning Bands algorithm. The realizations can be conditioned on measured values of the hydraulic conductivity using Kriging. This report describes a series of verification studies that have been carried out on the code. The first study concerns the accuracy of the implementation of the Turning Bands algorithm in HYDRASTAR. The implementation has been examined by evaluating the ensemble mean and covariance of the generated fields analytically and comparing them with their prescribed values. Three other studies were carried out in which HYDRASTAR was used to solve problems of uniform mean flow and to calculate the transport and dispersion of fluid particles. In all three cases the hydraulic conductivity fields were unconditioned. The first two were two-dimensional: one at small values of the variance of the logarithm of the hydraulic conductivity for which there exists analytical results that the code can be compared with, and one at moderate variance where the results can only be compared with those obtained by another code. The third problem was three dimensional with a small variance and again analytical results are available for comparison. 14 refs, 24 figs.

  14. Characterizing hydraulic conductivity with the direct-push permeameter

    Science.gov (United States)

    Butler, J.J.; Dietrich, P.; Wittig, V.; Christy, T.

    2007-01-01

    The direct-push permeameter (DPP) is a promising approach for obtaining high-resolution information about vertical variations in hydraulic conductivity (K) in shallow unconsolidated settings. This small-diameter tool, which consists of a short screened section with a pair of transducers inset in the tool near the screen, is pushed into the subsurface to a depth at which a K estimate is desired. A short hydraulic test is then performed by injecting water through the screen at a constant rate (less than 4 L/min) while pressure changes are monitored at the transducer locations. Hydraulic conductivity is calculated using the injection rate and the pressure changes in simple expressions based on Darcy's Law. In units of moderate or higher hydraulic conductivity (more than 1 m/d), testing at a single level can be completed within 10 to 15 min. Two major advantages of the method are its speed and the insensitivity of the K estimates to the zone of compaction created by tool advancement. The potential of the approach has been assessed at two extensively studied sites in the United States and Germany over a K range commonly faced in practical field investigations (0.02 to 500 m/d). The results of this assessment demonstrate that the DPP can provide high-resolution K estimates that are in good agreement with estimates obtained through other means. ?? 2007 National Ground Water Association.

  15. Measurement of Fracture Geometry for Accurate Computation of Hydraulic Conductivity

    Science.gov (United States)

    Chae, B.; Ichikawa, Y.; Kim, Y.

    2003-12-01

    Fluid flow in rock mass is controlled by geometry of fractures which is mainly characterized by roughness, aperture and orientation. Fracture roughness and aperture was observed by a new confocal laser scanning microscope (CLSM; Olympus OLS1100). The wavelength of laser is 488nm, and the laser scanning is managed by a light polarization method using two galvano-meter scanner mirrors. The system improves resolution in the light axis (namely z) direction because of the confocal optics. The sampling is managed in a spacing 2.5 μ m along x and y directions. The highest measurement resolution of z direction is 0.05 μ m, which is the more accurate than other methods. For the roughness measurements, core specimens of coarse and fine grained granites were provided. Measurements were performed along three scan lines on each fracture surface. The measured data were represented as 2-D and 3-D digital images showing detailed features of roughness. Spectral analyses by the fast Fourier transform (FFT) were performed to characterize on the roughness data quantitatively and to identify influential frequency of roughness. The FFT results showed that components of low frequencies were dominant in the fracture roughness. This study also verifies that spectral analysis is a good approach to understand complicate characteristics of fracture roughness. For the aperture measurements, digital images of the aperture were acquired under applying five stages of uniaxial normal stresses. This method can characterize the response of aperture directly using the same specimen. Results of measurements show that reduction values of aperture are different at each part due to rough geometry of fracture walls. Laboratory permeability tests were also conducted to evaluate changes of hydraulic conductivities related to aperture variation due to different stress levels. The results showed non-uniform reduction of hydraulic conductivity under increase of the normal stress and different values of

  16. HYDRAULIC CONDUCTIVITY OF GCL WITH BENTONITE – SILICA FUME MATRIX

    Directory of Open Access Journals (Sweden)

    Mudimby Andal

    2012-12-01

    Full Text Available This paper presents the influence of partial replacement of bentonite by silica fume which is used in the manufacture of Geosynthetic Clay Liner (GCL. Geosynthetic Clay Liners consist bentonite (Sodium Based sandwiched between two geotextile. Benotinite, having low permeability imparts better hydraulic performance to the GCL to act as liner. In this investigation, an attempt has been made to study the hydraulic conductivity of GCL with modified Bentonite. The bentonite is partially replaced by silica fume, a waste product of ferroalloy industries. Silica fume reduces the cracking characteristics of bentonite on desiccation. The replacement levels varied from 0% to 50% at a gradual increment of 5%. The test results indicated that partial replacement of bentonite by silica fume did not affected the permeability of bentonite even at 30%. Beyond 45% replacement levels the bentonite- silica fume mixtures showed increased permeability. This increased permeability also well within permeability limits of liners 1×10-9 m/sec.

  17. HYDRAULIC CONDUCTIVITY OF GCL WITH BENTONITE - SILICA FUME MATRIX

    Directory of Open Access Journals (Sweden)

    M. Andal

    2012-01-01

    Full Text Available This paper presents the influence of partial replacement of bentonite by silica fume which is used in the manufacture of Geosynthetic Clay Liner (GCL. Geosynthetic Clay Liners consist bentonite (Sodium Based sandwiched between two geotextile. Benotinite, having low permeability imparts better hydraulic performance to the GCL to act as liner. In this investigation, an attempt has been made to study the hydraulic conductivity of GCL with modified Bentonite. The bentonite is partially replaced by silica fume, a waste product of ferroalloy industries. Silica fume reduces the cracking characteristics of bentonite on desiccation. The replacement levels varied from 0% to 50% at a gradual increment of 5%. The test results indicated that partial replacement of bentonite by silica fume did not affected the permeability of bentonite even at 30%. Beyond 45% replacement levels the bentonite- silica fume mixtures showed increased permeability. This increased permeability also well within permeability limits of liners 1×10-9m/sec.

  18. Conductive nanomaterials for printed electronics.

    Science.gov (United States)

    Kamyshny, Alexander; Magdassi, Shlomo

    2014-09-10

    This is a review on recent developments in the field of conductive nanomaterials and their application in printed electronics, with particular emphasis on inkjet printing of ink formulations based on metal nanoparticles, carbon nanotubes, and graphene sheets. The review describes the basic properties of conductive nanomaterials suitable for printed electronics (metal nanoparticles, carbon nanotubes, and graphene), their stabilization in dispersions, formulations of conductive inks, and obtaining conductive patterns by using various sintering methods. Applications of conductive nanomaterials for electronic devices (transparent electrodes, metallization of solar cells, RFID antennas, TFTs, and light emitting devices) are also briefly reviewed.

  19. Estimating the hydraulic conductivity of two-dimensional fracture networks

    Science.gov (United States)

    Leung, C. T.; Zimmerman, R. W.

    2010-12-01

    Most oil and gas reservoirs, as well as most potential sites for nuclear waste disposal, are naturally fractured. In these sites, the network of fractures will provide the main path for fluid to flow through the rock mass. In many cases, the fracture density is so high as to make it impractical to model it with a discrete fracture network (DFN) approach. For such rock masses, it would be useful to have recourse to analytical, or semi-analytical, methods to estimate the macroscopic hydraulic conductivity of the fracture network. We have investigated single-phase fluid flow through stochastically generated two-dimensional fracture networks. The centres and orientations of the fractures are uniformly distributed, whereas their lengths follow either a lognormal distribution or a power law distribution. We have considered the case where the fractures in the network each have the same aperture, as well as the case where the aperture of each fracture is directly proportional to the fracture length. The discrete fracture network flow and transport simulator NAPSAC, developed by Serco (Didcot, UK), is used to establish the “true” macroscopic hydraulic conductivity of the network. We then attempt to match this conductivity using a simple estimation method that does not require extensive computation. For our calculations, fracture networks are represented as networks composed of conducting segments (bonds) between nodes. Each bond represents the region of a single fracture between two adjacent intersections with other fractures. We assume that the bonds are arranged on a kagome lattice, with some fraction of the bonds randomly missing. The conductance of each bond is then replaced with some effective conductance, Ceff, which we take to be the arithmetic mean of the individual conductances, averaged over each bond, rather than over each fracture. This is in contrast to the usual approximation used in effective medium theories, wherein the geometric mean is used. Our

  20. An Integrated View of Whole-Tree Hydraulic Architecture. Does Stomatal or Hydraulic Conductance Determine Whole Tree Transpiration?

    Directory of Open Access Journals (Sweden)

    Juan Rodríguez-Gamir

    Full Text Available Hydraulic conductance exerts a strong influence on many aspects of plant physiology, namely: transpiration, CO2 assimilation, growth, productivity or stress response. However we lack full understanding of the contribution of root or shoot water transport capacity to the total water balance, something which is difficult to study in trees. Here we tested the hypothesis that whole plant hydraulic conductance modulates plant transpiration using two different seedlings of citrus rootstocks, Poncirus trifoliata (L. Raf. and Cleopatra mandarin (Citrus reshni Hort ex Tan.. The two genotypes presented important differences in their root or shoot hydraulic conductance contribution to whole plant hydraulic conductance but, even so, water balance proved highly dependent on whole plant conductance. Further, we propose there is a possible equilibrium between root and shoot hydraulic conductance, similar to that between shoot and root biomass production, which could be related with xylem anatomy.

  1. An Integrated View of Whole-Tree Hydraulic Architecture. Does Stomatal or Hydraulic Conductance Determine Whole Tree Transpiration?

    Science.gov (United States)

    Rodríguez-Gamir, Juan; Primo-Millo, Eduardo; Forner-Giner, María Ángeles

    2016-01-01

    Hydraulic conductance exerts a strong influence on many aspects of plant physiology, namely: transpiration, CO2 assimilation, growth, productivity or stress response. However we lack full understanding of the contribution of root or shoot water transport capacity to the total water balance, something which is difficult to study in trees. Here we tested the hypothesis that whole plant hydraulic conductance modulates plant transpiration using two different seedlings of citrus rootstocks, Poncirus trifoliata (L.) Raf. and Cleopatra mandarin (Citrus reshni Hort ex Tan.). The two genotypes presented important differences in their root or shoot hydraulic conductance contribution to whole plant hydraulic conductance but, even so, water balance proved highly dependent on whole plant conductance. Further, we propose there is a possible equilibrium between root and shoot hydraulic conductance, similar to that between shoot and root biomass production, which could be related with xylem anatomy.

  2. Frequency-dependent effective hydraulic conductivity of strongly heterogeneous media.

    Science.gov (United States)

    Caspari, E; Gurevich, B; Müller, T M

    2013-10-01

    The determination of the transport properties of heterogeneous porous rocks, such as an effective hydraulic conductivity, arises in a range of geoscience problems, from groundwater flow analysis to hydrocarbon reservoir modeling. In the presence of formation-scale heterogeneities, nonstationary flows, induced by pumping tests or propagating elastic waves, entail localized pressure diffusion processes with a characteristic frequency depending on the pressure diffusivity and size of the heterogeneity. Then, on a macroscale, a homogeneous equivalent medium exists, which has a frequency-dependent effective conductivity. The frequency dependence of the conductivity can be analyzed with Biot's equations of poroelasticity. In the quasistatic frequency regime of this framework, the slow compressional wave is a proxy for pressure diffusion processes. This slow compressional wave is associated with the out-of-phase motion of the fluid and solid phase, thereby creating a relative fluid-solid displacement vector field. Decoupling of the poroelasticity equations gives a diffusion equation for the fluid-solid displacement field valid in a poroelastic medium with spatial fluctuations in hydraulic conductivity. Then, an effective conductivity is found by a Green's function approach followed by a strong-contrast perturbation theory suggested earlier in the context of random dielectrics. This theory leads to closed-form expressions for the frequency-dependent effective conductivity as a function of the one- and two-point probability functions of the conductivity fluctuations. In one dimension, these expressions are consistent with exact solutions in both low- and high-frequency limits for arbitrary conductivity contrast. In 3D, the low-frequency limit depends on the details of the microstructure. However, the derived approximation for the effective conductivity is consistent with the Hashin-Shtrikman bounds.

  3. Effective soil hydraulic conductivity predicted with the maximum power principle

    Science.gov (United States)

    Westhoff, Martijn; Erpicum, Sébastien; Archambeau, Pierre; Pirotton, Michel; Zehe, Erwin; Dewals, Benjamin

    2016-04-01

    Drainage of water in soils happens for a large extent through preferential flowpaths, but these subsurface flowpaths are extremely difficult to observe or parameterize in hydrological models. To potentially overcome this problem, thermodynamic optimality principles have been suggested to predict effective parametrization of these (sub-grid) structures, such as the maximum entropy production principle or the equivalent maximum power principle. These principles have been successfully applied to predict heat transfer from the Equator to the Poles, or turbulent heat fluxes between the surface and the atmosphere. In these examples, the effective flux adapts itself to its boundary condition by adapting its effective conductance through the creation of e.g. convection cells. However, flow through porous media, such as soils, can only quickly adapt its effective flow conductance by creation of preferential flowpaths, but it is unknown if this is guided by the aim to create maximum power. Here we show experimentally that this is indeed the case: In the lab, we created a hydrological analogue to the atmospheric model dealing with heat transport between Equator and poles. The experimental setup consists of two freely draining reservoirs connected with each other by a confined aquifer. By adding water to only one reservoir, a potential difference will build up until a steady state is reached. From the steady state potential difference and the observed flow through the aquifer, and effective hydraulic conductance can be determined. This observed conductance does correspond to the one maximizing power of the flux through the confined aquifer. Although this experiment is done in an idealized setting, it opens doors for better parameterizing hydrological models. Furthermore, it shows that hydraulic properties of soils are not static, but they change with changing boundary conditions. A potential limitation to the principle is that it only applies to steady state conditions

  4. Hydraulic conductivity and soil-sewage sludge interactions

    Directory of Open Access Journals (Sweden)

    Silvio Romero de Melo Ferreira

    2011-10-01

    Full Text Available One of the main problems faced by humanity is pollution caused by residues resulting from the production and use of goods, e.g, sewage sludge. Among the various alternatives for its disposal, the agricultural use seems promising. The purpose of this study was to evaluate the hydraulic conductivity and interaction of soil with sandy-silty texture, classified as Spodosols, from the Experimental Station Itapirema - IPA, in Goiana, state of Pernambuco, in mixtures with sewage sludge from the Mangueira Sewage Treatment Station, in the city of Recife, Pernambuco at rates of 25, 50 and 75 Mg ha-1. Tests were conducted to let water percolate the natural saturated soil and soil-sludge mixtures to characterize their physical, chemical, and microstructural properties as well as hydraulic conductivity. Statistical data analysis showed that the presence of sewage sludge in soils leads to an increase of the < 0.005 mm fraction, reduction in real specific weight and variation in optimum moisture content from 11.60 to 12.90 % and apparent specific dry weight from 17.10 and 17.50 kN m-3. In the sludge-soil mixture, the quartz grains were covered by sludge and filling of the empty soil macropores between grains. There were changes in the chemical characteristics of soil and effluent due to sewage sludge addition and a small decrease in hydraulic conductivity. The results indicate the possibility that soil acidity influenced the concentrations of the elements found in the leachate, showing higher levels at higher sludge doses. It can be concluded that the leaching degree of potentially toxic elements from the sewage sludge treatments does not harm the environment.

  5. Root hydraulic conductivity and adjustments in stomatal conductance: hydraulic strategy in response to salt stress in a halotolerant species.

    Science.gov (United States)

    Vitali, Victoria; Bellati, Jorge; Soto, Gabriela; Ayub, Nicolás D; Amodeo, Gabriela

    2015-11-24

    Recent advances at the molecular level are introducing a new scenario that needs to be integrated into the analysis of plant hydraulic properties. Although it is not yet clear to what extent this scenario alters the current proposal for the hydraulic circuit models, it introduces new insights when studying plants that are able to easily overcome water restrictions. In this context, our aim was to explore water adjustments in a halotolerant model (Beta vulgaris) by studying the coordination between the root in terms of root hydraulic conductivity (Lpr) and the shoot as reflected in the stomatal conductance (gs). The root water pathways were also analysed in terms of root suberization (apoplastic barrier) and aquaporin transcript levels (cell-to-cell pathway). Beta vulgaris showed the ability to rapidly lose (4 h) and gain (24 h) turgor when submitted to salt stress (200 mM). The reduction profile observed in Lpr and gs was consistent with a coupled process. The tuning of the root water flow involved small variations in the studied aquaporin's transcripts before anatomical modifications occurred. Exploring Lpr enhancement after halting the stress contributed to show not only a different profile in restoring Lpr but also the capacity to uncouple Lpr from gs. Beta vulgaris root plays a key role and can anticipate water loss before the aerial water status is affected.

  6. Changes in entrapped gas content and hydraulic conductivity with pressure.

    Science.gov (United States)

    Marinas, Maricris; Roy, James W; Smith, James E

    2013-01-01

    Water table fluctuations continuously introduce entrapped air bubbles into the otherwise saturated capillary fringe and groundwater zone, which reduces the effective (quasi-saturated) hydraulic conductivity, K(quasi), thus impacting groundwater flow, aquifer recharge and solute and contaminant transport. These entrapped gases will be susceptible to compression or expansion with changes in water pressure, as would be expected with water table (and barometric pressure) fluctuations. Here we undertake laboratory experiments using sand-packed columns to quantify the effect of water table changes of up to 250 cm on the entrapped gas content and the quasi-saturated hydraulic conductivity, and discuss our ability to account for these mechanisms in ground water models. Initial entrapped air contents ranged between 0.080 and 0.158, with a corresponding K(quasi) ranging between 2 and 6 times lower compared to the K(s) value. The application of 250 cm of water pressure caused an 18% to 26% reduction in the entrapped air content, resulting in an increase in K(quasi) by 1.16 to 1.57 times compared to its initial (0 cm water pressure) value. The change in entrapped air content measured at pressure step intervals of 50 cm, was essentially linear, and could be modeled according to the ideal gas law. Meanwhile, the changes in K(quasi) with compression-expansion of the bubbles because of pressure changes could be adequately captured with several current hydraulic conductivity models. © Ground Water 2012 and © Her Majesty the Queen in Right of Canada 2012. Ground Water © 2012, National Ground Water Association.

  7. Simple Predictive Models for Saturated Hydraulic Conductivity of Technosands

    DEFF Research Database (Denmark)

    Arthur, Emmanuel; Razzaghi, Fatemeh; Møldrup, Per

    2012-01-01

    Accurate estimation of saturated hydraulic conductivity (Ks) of technosands (gravel-free, coarse sands with negligible organic matter content) is important for irrigation and drainage management of athletic fields and golf courses. In this study, we developed two simple models for predicting Ks......-connectivity parameter (m) obtained for pure coarse sand after fitting to measured Ks data was 1.68 for both models and in good agreement with m values obtained from recent solute and gas diffusion studies. Both the modified K-C and R-C models are easy to use and require limited parameter input, and both models gave...

  8. Reduction of saltwater intrusion by modifying hydraulic conductivity

    Science.gov (United States)

    Strack, O. D. L.; Stoeckl, L.; Damm, K.; Houben, G.; Ausk, B. K.; de Lange, W. J.

    2016-09-01

    We present an approach for reducing saltwater intrusion in coastal aquifers by artificially reducing the hydraulic conductivity in the upper part of selected areas by using a precipitate. We apply a previously presented analytical approach to develop formulas useful for the design of artificial barriers. Equations for the location of the tip of the saltwater wedge are presented and verified through a sand-tank experiment. The analysis is capable of computing discharges exactly, but requires the Dupuit-Forchheimer approximation to compute points of the interface between flowing fresh and stationary saltwater. We consider a vertical coastline and boundaries in the freshwater zone of either given discharge or given head. We demonstrate in the paper that reduction of the hydraulic conductivity in the upper part of a coastal aquifer will result in a decrease of saltwater intrusion, and present analytic expressions that can be used for design purposes. The previously presented analytical approach can be applied to design systems to reduce saltwater intrusion caused by pumping inland from the zone that contains saline groundwater.

  9. Effects of the hydraulic conductivity microstructure on macrodispersivity

    Science.gov (United States)

    Di Dato, Mariaines; de Barros, Felipe P. J.; Fiori, Aldo; Bellin, Alberto

    2016-09-01

    Heterogeneity of the hydraulic properties is one of the main causes of the seemingly random distribution of solute concentration observed in contaminated aquifers, with macrodispersivity providing a global measure of spreading. Earlier studies on transport of solutes in heterogeneous formations, either theoretical or numerical, expressed dispersivity as a function of the geostatistical properties of the hydraulic conductivity K. In most cases, K follows a second-order statistical characterization, which may not be adequate when heterogeneity is high. In this work, we adopt the Multi-Indicator Model-Self Consistent Approach (MIMSCA) to compute the longitudinal and transverse macrodispersivity. This methodology enables to model the K field by using geological inclusions of different shapes and orientation (defined here as the microstructure), while replicating the heterogeneous macrostructure obtained by the second-order statistics. The above scheme attempts to reproduce the effect on macrodispersion of different distribution and orientation of local facies, and for instance it may represent the orientation and spatial features of the layers that are often observed in aquifers. The relevant impact of the microstructure on effective conductivity, longitudinal and transverse macrodispersivities is analyzed and discussed, for both binary and lognormally distributed K fields.

  10. Effects of temperature and thermally-induced microstructure change on hydraulic conductivity of Boom Clay

    Directory of Open Access Journals (Sweden)

    W.Z. Chen

    2017-06-01

    Full Text Available Boom Clay is one of the potential host rocks for deep geological disposal of high-level radioactive nuclear waste in Belgium. In order to investigate the mechanism of hydraulic conductivity variation under complex thermo-mechanical coupling conditions and to better understand the thermo-hydro-mechanical (THM coupling behaviour of Boom Clay, a series of permeability tests using temperature-controlled triaxial cell has been carried out on the Boom Clay samples taken from Belgian underground research laboratory (URL HADES. Due to its sedimentary nature, Boom Clay presents across-anisotropy with respect to its sub-horizontal bedding plane. Direct measurements of the vertical (Kv and horizontal (Kh hydraulic conductivities show that the hydraulic conductivity at 80 °C is about 2.4 times larger than that at room temperature (23 °C, and the hydraulic conductivity variation with temperature is basically reversible during heating–cooling cycle. The anisotropic property of Boom Clay is studied by scanning electron microscope (SEM tests, which highlight the transversely isotropic characteristics of intact Boom Clay. It is shown that the sub-horizontal bedding feature accounts for the horizontal permeability higher than the vertical one. The measured increment in hydraulic conductivity with temperature is lower than the calculated one when merely considering the changes in water kinematic viscosity and density with temperature. The nuclear magnetic resonance (NMR tests have also been carried out to investigate the impact of microstructure variation on the THM properties of clay. The results show that heating under unconstrained boundary condition will produce larger size of pores and weaken the microstructure. The discrepancy between the hydraulic conductivity experimentally measured and predicted (considering water viscosity and density changes with temperature can be attributed to the microstructural weakening effect on the thermal volume change

  11. Dentin permeability: effects of temperature on hydraulic conductance.

    Science.gov (United States)

    Pashley, D H; Thompson, S M; Stewart, F P

    1983-09-01

    The rates of fluid movement across dentin discs, in vitro, were measured at 10, 20, 30, 40, and 50 degrees C in unetched and acid-etched dentin. Increasing the temperature 40 degrees (i.e., from 10 to 50 degrees C) resulted in a 1.8-fold increase in fluid flow in unetched dentin, which was of a magnitude similar to the decrease in viscosity that occurred over the same temperature range. In acid-etched dentin, the 40 degrees C temperature change produced more than a four-fold increase in fluid conductance, more than double that which could be accounted for by changes in viscosity. Analysis of the data suggests that this additional increment in hydraulic conductance is due to thermal expansion-induced increases in tubular diameter.

  12. Effects Of Evaporation Rate of Some Common Organic Contaminants on Hydraulic Conductivity of Aquifer Sand

    Science.gov (United States)

    Saud, Q. J.; Hasan, S. E.

    2014-12-01

    As part of a larger study to investigate potential effects of hydrocarbons on the geotechnical properties of aquifer solids, a series of laboratory experiments were carried out to ascertain the influence of evaporation rate of some common and widespread organic contaminants on the hydraulic conductivity of aquifer sand. Gasoline and its constituent chemicals-benzene, toluene, ethylbenzene, xylene (BTEX), isooctane- and trichloroethylene (TCE) were used to contaminate sand samples collected from the aquifer and vadose zone, at varying concentrations for extended periods of time. The goal was to study any change in the chemical makeup of the contaminants and its control on hydraulic conductivity of the sand. It was found that: (a) gasoline breaks down into constituent compounds when subjected to evaporation, e.g. during oil spills and leaks; and (b) lighter compounds volatilize faster and in the following order: TCE> benzene > isooctane > toluene > gasoline> ethylbenzene > xylene. In addition, these contaminants also caused a decrease in hydraulic conductivity of sand by up to 60% as compared to the uncontaminated sand. The inherent differences in the chemical structure of contaminating chemicals influenced hydraulic conductivity such that the observed decrease was greater for aliphatic than aromatic and chlorinated hydrocarbons. The presentation includes details of the experimental set up; evaporation rate, and geotechnical tests; X-ray diffraction and scanning electron microscope studies; and data analyses and interpretation. Rate of evaporation test indicates that residual LNAPLs will occupy a certain portion of the pores in the soil either as liquid or vapor phase in the vadose zone, and will create a coating on the adjacent solid mineral grains in the aquifer. Replacement of air by the LNAPLs along with grain coatings and the intramolecular forces would impede groundwater movement, thus affecting overall permeability of contaminated aquifers. Keywords: aquifer

  13. Thermally conducting electron transfer polymers

    Science.gov (United States)

    Byrd, N. R.; Jenkins, R. K.; Lister, J. L.

    1969-01-01

    New polymeric material exhibits excellent physical shock protection, high electrical resistance, and thermal conductivity. It is especially useful for electronic circuitry, such as subminiaturization of components and modular construction of circuits.

  14. DEPTH CONTINUOUS HYDRAULIC CONDUCTIVITY PROFILING USING AN ACTIVE SOURCE PENETROMETER

    Science.gov (United States)

    Fitzgerald, M.; Elsworth, D.

    2009-12-01

    A method is developed to recover depth-continuous hydraulic conductivity profiles of an unconsolidated saturated aquifer using an active source penetrometer, the Hydraulic Profiling Tool (HPT). The tool yields estimates of K through continuous injection of fluid in the subsurface from a small port on the probe shaft while controlled measurements of net applied fluid pressure required to maintain a specified flow rate (typically 350 mL/min) are recorded. The tool gathers these data of flow rate and measured applied pressure during halted and constant-rate penetration (typically 2cm/sec) of the probe. The analysis is developed in two parts, first to explore the interplay between advective effects controlled by penetration rate and secondly flow volume effects controlled by the targeted flow rate. These two effects are analyzed through their respective influence on the measured applied pressure response in ΔP/σv’-Q/ΔP space, which shows a linear relationship for the flow rate to applied pressure response when Q/ΔP > 1 and when Q/ΔP 1. The analysis shows that penetration rate does not significantly influence the applied pressure response at the tested penetration rates (0 ≤ U(cm/s)≤ 4). The targeted applied flow rate does however influence the applied pressure response as flow rates less than ~300 mL/min show a scattering of the data in ΔP/σv’-Q/ΔP space, where above 300 mL/min the data begins to form a linear response. A targeted flow rate of QT = 400mL/min is suggested as a suitable flow rate based on this analysis. Measurements of hydraulic conductivity are then obtained for the HPT data through the derivation of an equation based on a recast form of Darcy’s law where considerations of the flow geometry as K = (QHPT/ΔP)(δw/πΦ). K profiles obtained for the HPT system are then compared against K profiles obtained from an independent method (PSU permeameter) and yield a good correlation between the two methods.

  15. Measuring lateral saturated soil hydraulic conductivity at different spatial scales

    Science.gov (United States)

    Di Prima, Simone; Marrosu, Roberto; Pirastru, Mario; Niedda, Marcello

    2017-04-01

    Among the soil hydraulic properties, saturated soil hydraulic conductivity, Ks, is particularly important since it controls many hydrological processes. Knowledge of this soil property allows estimation of dynamic indicators of the soil's ability to transmit water down to the root zone. Such dynamic indicators are valuable tools to quantify land degradation and developing 'best management' land use practice (Castellini et al., 2016; Iovino et al., 2016). In hillslopes, lateral saturated soil hydraulic conductivity, Ks,l, is a key factor since it controls subsurface flow. However, Ks,l data collected by point-scale measurements, including infiltrations tests, could be unusable for interpreting field hydrological processes and particularly subsurface flow in hillslopes. Therefore, they are generally not representative of subsurface processes at hillslope-scale due mainly to soil heterogeneities and the unknown total extent and connectivity of macropore network in the porous medium. On the other hand, large scale Ks,l measurements, which allow to average soil heterogeneities, are difficult and costly, thus remain rare. Reliable Ks,l values should be measured on a soil volume similar to the representative elementary volume (REV) in order to incorporate the natural heterogeneity of the soil. However, the REV may be considered site-specific since it is expected to increase for soils with macropores (Brooks et al., 2004). In this study, laboratory and in-situ Ks,l values are compared in order to detect the dependency Ks,l from the spatial scale of investigation. The research was carried out at a hillslope located in the Baratz Lake watershed, in northwest Sardinia, Italy, characterized by degraded vegetation (grassland established after fire or clearing of the maquis). The experimental area is about 60 m long, with an extent of approximately 2000 m2, and a mean slope of 30%. The soil depth is about 35 to 45 cm. The parent material is a very dense grayish, altered

  16. Interstitial hydraulic conductivity and interstitial fluid pressure for avascular or poorly vascularized tumors.

    Science.gov (United States)

    Liu, L J; Schlesinger, M

    2015-09-07

    A correct description of the hydraulic conductivity is essential for determining the actual tumor interstitial fluid pressure (TIFP) distribution. Traditionally, it has been assumed that the hydraulic conductivities both in a tumor and normal tissue are constant, and that a tumor has a much larger interstitial hydraulic conductivity than normal tissue. The abrupt transition of the hydraulic conductivity at the tumor surface leads to non-physical results (the hydraulic conductivity and the slope of the TIFP are not continuous at tumor surface). For the sake of simplicity and the need to represent reality, we focus our analysis on avascular or poorly vascularized tumors, which have a necrosis that is mostly in the center and vascularization that is mostly on the periphery. We suggest that there is an intermediary region between the tumor surface and normal tissue. Through this region, the interstitium (including the structure and composition of solid components and interstitial fluid) transitions from tumor to normal tissue. This process also causes the hydraulic conductivity to do the same. We introduce a continuous variation of the hydraulic conductivity, and show that the interstitial hydraulic conductivity in the intermediary region should be monotonically increasing up to the value of hydraulic conductivity in the normal tissue in order for the model to correspond to the actual TIFP distribution. The value of the hydraulic conductivity at the tumor surface should be the lowest in value.

  17. Predicting saturated hydraulic conductivity using soil morphological properties

    Directory of Open Access Journals (Sweden)

    Gülay Karahan

    2016-01-01

    Full Text Available Many studies have been conducted to predict soil saturated hydraulic conductivity (Ks by parametric soil properties such as bulk density and particle-size distribution. Although soil morphological properties have a strong effect on Ks, studies predicting Ks by soil morphological properties such as type, size, and strength of soil structure; type, orientation and quantity of soil pores and roots and consistency are rare. This study aimed at evaluating soil morphological properties to predict Ks. Undisturbed soil samples (15 cm length and 8.0 cm id. were collected from topsoil (0-15 cm and subsoil (15-30 cm (120 samples with a tractor operated soil sampler at sixty randomly selected sampling sites on a paddy field and an adjecent grassland in Central Anatolia (Cankırı, Turkey. Synchronized disturbed soil samples were taken from the same sampling sites and sampling depths for basic soil analyses. Saturated hydraulic conductivity was measured on the soil columns using a constant-head permeameter. Following the Ks measurements, the upper part of soil columns were covered to prevent evaporation and colums were left to drain in the laboratory. When the water flow through the column was stopped, a subsample were taken for bulk density and then soil columns were disturbed for describing the soil morphological properties. In addition, soil texture, bulk density, pH, field capacity, wilting point, cation exchange capacity, specific surface area, aggregate stability, organic matter, and calcium carbonate were measured on the synchronized disturbed soil samples. The data were divided into training (80 data values and validation (40 data values sets. Measured values of Ks ranged from 0.0036 to 2.14 cmh-1 with a mean of 0.86 cmh-1. The Ks was predicted from the soil morphological and parametric properties by stepwise multiple linear regression analysis. Soil structure class, stickiness, pore-size, root-size, and pore-quantity contributed to the Ks prediction

  18. Effects of distance from the pulp and thickness on the hydraulic conductance of human radicular dentin.

    Science.gov (United States)

    Fogel, H M; Marshall, F J; Pashley, D H

    1988-11-01

    The purposes of this study were: (1) to measure the effect of distance from the pulp on the hydraulic conductance of human radicular dentin; (2) to determine the influence of dentin thickness on the rates of fluid flow; and (3) to attempt to correlate dentinal tubule densities and diameters with root dentin hydraulic conductance. Dentin slabs prepared from extracted, unerupted, human third molar teeth were placed in a split-chamber device to permit quantitation of fluid filtration rate (hydraulic conductance). In the SEM portion of the study, dentinal tubule numbers and diameters were recorded. The results indicated that radicular dentin hydraulic conductance decreased with distance from the pulp and with increasing dentin thickness. Tubule density and diameter correlated well with the measured hydraulic conductances. The relatively low hydraulic conductance of outer root dentin makes it a significant barrier to fluid movement across root structure.

  19. [Effects of invertebrate bioturbation on vertical hydraulic conductivity of streambed for a river].

    Science.gov (United States)

    Ren, Chao-Liang; Song, Jin-Xi; Yang, Xiao-Gang; Xue, Jian

    2013-11-01

    Streambed hydraulic conductivity is a key factor influencing water exchange between surface water and groundwater. However, the streambed invertebrate bioturbation has a great effect on the hydraulic conductivity. In order to determine the impact of invertebrate bioturbation on streambed hydraulic conductivity, the investigation of invertebrate bioturbation and in-situ test of vertical hydraulic conductivity of streambed are simultaneously conducted at five points along the main stream of the Weihe River. Firstly, correlation between the streambed vertical hydraulic conductivity and grain size distribution is analyzed. Secondly, type and density of the invertebrate and their correlation to hydraulic conductivity are determined. Finally, the effect of invertebrate bioturbation on the streambed hydraulic conductivity is illustrated. The results show that the vertical hydraulic conductivity and biological density of invertebrate are 18.479 m x d(-1) and 139 ind x m(-2), respectively for the Caotan site, where sediment composition with a large amount of sand and gravel particles. For Meixian site, the sediment constitutes a large amount of silt and clay particles, in which the vertical hydraulic conductivity and biological density of invertebrate are 2.807 m x d(-1) and 2 742 ind x m(-2) respectively. Besides, for the low permeability of four sites (Meixian, Xianyang, Lintong and Huaxian), grain size particles are similar while the vertical hydraulic conductivity and biological density of invertebrate are significantly different from one site to another. However, for each site, the vertical hydraulic conductivity closely related to biological density of invertebrate, the Pearson correlation coefficient is 0.987. It can be concluded that both grain size particles and invertebrate bioturbation influence sediment permeability. For example, higher values of streambed hydraulic conductivity from strong permeability site mainly due to the large amount of large-size particles

  20. Effect of Irrigation Water Quality on Soil Hydraulic Conductivity

    Institute of Scientific and Technical Information of China (English)

    XIAOZHEN-HUA; B.PRENDERGAST; 等

    1992-01-01

    The effect of irrigation water quality on unsaturated hydraulic conductivity (HC) of undisturbed soil in field was studied.Results show that within the operating soil suction range (0-1.6 KPa) of disc permeameters,the higher the electric conductivity (EC) of irrigation water,the higher the soil HC became.The soil HC doubled when EC increased from 0.1 to 6.0ds m-1.High sodium-adsorption ratio(SAR) of irrigation water would have an unfavorable effect on soil HC.Soil HC decreased with the increasing of SAR,especially in the case of higher soil suction.An interaction existed between the effects of EC and SAR of irrigation water on soil HC.The HC of unsaturated soil dependent upon the macropores in surface soil decreased by one order of magnitude with 1 KPa increase of soil suction.In the study on the effect of very low soluble salt concentration (EC=0.1 ds m-1 of irrigation water on soil HC,soil HC was found to be lowered by 30% as a consequence of blocking up of some continuous pores by the dispersed and migrated clay particles.Nonlinear successive regression analysis and significance test show that the effects of EC and SAR of irrigation water on soil HC reached the extremely significant level.

  1. Beneficial impact of polymer treatment of Ca-bentonites on long term hydraulic conductivity

    OpenAIRE

    Di Emidio, Gemmina; De Camillis, Michela; Bezuijen, Adam; Verastegui Flores, R.D.

    2014-01-01

    The hydraulic conductivity of geosynthetic clay liners for the confinement of waste disposal facilities mainly depends on the hydraulic conductivity of the core bentonite clay encased between the two geotextiles. Bentonite clay is the most common material for geosynthetic clay liners. Even thought, sodium bentonite has the lowest hydraulic conductivity to water, calcium bentonite is widely used because of low cost and availability. This research concerns the evaluation of the treatment of cal...

  2. Coordination of stem and leaf hydraulic conductance in southern California shrubs: a test of the hydraulic segmentation hypothesis.

    Science.gov (United States)

    Pivovaroff, Alexandria L; Sack, Lawren; Santiago, Louis S

    2014-08-01

    Coordination of water movement among plant organs is important for understanding plant water use strategies. The hydraulic segmentation hypothesis (HSH) proposes that hydraulic conductance in shorter lived, 'expendable' organs such as leaves and longer lived, more 'expensive' organs such as stems may be decoupled, with resistance in leaves acting as a bottleneck or 'safety valve'. We tested the HSH in woody species from a Mediterranean-type ecosystem by measuring leaf hydraulic conductance (Kleaf) and stem hydraulic conductivity (KS). We also investigated whether leaves function as safety valves by relating Kleaf and the hydraulic safety margin (stem water potential minus the water potential at which 50% of conductivity is lost (Ψstem-Ψ50)). We also examined related plant traits including the operating range of water potentials, wood density, leaf mass per area, and leaf area to sapwood area ratio to provide insight into whole-plant water use strategies. For hydrated shoots, Kleaf was negatively correlated with KS , supporting the HSH. Additionally, Kleaf was positively correlated with the hydraulic safety margin and negatively correlated with the leaf area to sapwood area ratio. Consistent with the HSH, our data indicate that leaves may act as control valves for species with high KS , or a low safety margin. This critical role of leaves appears to contribute importantly to plant ecological specialization in a drought-prone environment.

  3. Measurement of 3-D hydraulic conductivity in aquifer cores at in situ effective stresses.

    Science.gov (United States)

    Wright, Martin; Dillon, Peter; Pavelic, Paul; Peter, Paul; Nefiodovas, Andrew

    2002-01-01

    An innovative and nondestructive method to measure the hydraulic conductivity of drill core samples in horizontal and vertical directions within a triaxial cell has been developed. This has been applied to characterizing anisotropy and heterogeneity of a confined consolidated limestone aquifer. Most of the cores tested were isotropic, but hydraulic conductivity varied considerably and the core samples with lowest values were also the most anisotropic. Hydraulic conductivity decreased with increasing effective stress due to closure of microfractures caused by sampling for all core samples. This demonstrates the importance of replicating in situ effective stresses when measuring hydraulic conductivity of cores of deep aquifers in the laboratory.

  4. Hydraulic conductance of Acacia phyllodes (foliage) is driven by primary nerve (vein) conductance and density.

    Science.gov (United States)

    Sommerville, Katy E; Sack, Lawren; Ball, Marilyn C

    2012-01-01

    We determined effects of venation traits on hydraulic conductance of phyllodes (foliage), using an array of Acacia s.str. species with diverse phyllode morphologies as the source of variation. Measurements were made on phyllodes from 44 species, grown in common gardens but originating from different positions along a precipitation gradient. K(phyllode) varied 18-fold and was positively correlated with primary nerve hydraulic conductance, and with primary nerve (vein) density but not with minor nerve density, in contrast with previous studies of true leaves in other dicotyledons. Phyllodes with higher primary nerve density also had greater mass per area (PMA) and larger bundle sheath extensions (BSEs) from their minor nerves. We suggest that higher primary nerve conductivity and density may decrease the distance travelled in the high-resistance extra-xylem pathways of the phyllode. Further, larger BSEs may increase the area available for dispersion of water from the xylem to the extra-xylem tissue. High PMA phyllodes were more common in acacias from areas receiving lower annual precipitation. Maximizing efficient water movement through phyllodes may be more important where rainfall is meagre and infrequent, explaining relationships between nerve patterns and the climates of origin in Australian phyllodinous Acacia.

  5. Hydraulics.

    Science.gov (United States)

    Decker, Robert L.; Kirby, Klane

    This curriculum guide contains a course in hydraulics to train entry-level workers for automotive mechanics and other fields that utilize hydraulics. The module contains 14 instructional units that cover the following topics: (1) introduction to hydraulics; (2) fundamentals of hydraulics; (3) reservoirs; (4) lines, fittings, and couplers; (5)…

  6. MEASURING VERTICAL PROFILES OF HYDRAULIC CONDUCTIVITY WITH IN SITU DIRECT-PUSH METHODS

    Science.gov (United States)

    U.S. EPA (Environmental Protection Agency) staff developed a field procedure to measure hydraulic conductivity using a direct-push system to obtain vertical profiles of hydraulic conductivity. Vertical profiles were obtained using an in situ field device-composed of a Geopr...

  7. New empirical relationship between grain size distribution and hydraulic conductivity for ephemeral streambed sediments

    KAUST Repository

    Rosas, Jorge

    2014-07-19

    Grain size distribution, porosity, and hydraulic conductivity were determined for 39 sediment samples collected from ephemeral streams (wadis) in western Saudi Arabia. The measured hydraulic conductivity values were then compared to values calculated using 20 different empirical equations commonly used to estimate hydraulic conductivity from grain size analyses. It was found that most of the hydraulic conductivity values estimated from the empirical equations correlated very poorly with the measured hydraulic conductivity values. Modifications of the empirical equations, including changes to special coefficients and statistical offsets, were made to produce modified equations that considerably improved the hydraulic conductivity estimates from grain size data for wadi sediments. The Chapuis, Hazen, Kozeny, Slichter, Terzaghi, and Barr equations produced the best correlations, but still had relatively high predictive errors. The Chapius equation was modified for wadi sediments by incorporating mud percentage and the standard deviation (in phi units) into a new equation that reduced the predicted hydraulic conductivity error to ±14.1 m/day. The equation is best applied to ephemeral stream samples that have hydraulic conductive values greater than 2 m/day.

  8. Saturated hydraulic conductivity and porosity within macroaggregates modified by tillage

    Energy Technology Data Exchange (ETDEWEB)

    Park, E.J.; Smucker, A.J.M. (MSU)

    2010-07-20

    Greater knowledge of intraaggregate porosity modifications by tillage conveys new information for identifying additional hydrologic, ion retention, and aggregate stability responses to specific management practices. Macroaggregates, 2 to 4, 4 to 6.3, and 6.3 to 9.5 mm across, were separated into multiple concentric layers and their porosities were determined. Saturated hydraulic conductivity (K{sub s}) of multiple aggregate fractions from two soil types subjected to conventional tillage (CT), no tillage (NT), and native forest (NF) soils were measured individually to identify the effects of tillage on aggregate structure, porosity, and K{sub s}. Intraaggregate porosities were the highest in NF aggregates. Greater porosities were identified in exterior layers of soil aggregates from all treatments. Lowest intraaggregate porosities were observed in the central regions of CT aggregates. Soil aggregates, 6.3 to 9.5 mm across, had the greatest total porosities, averaging 37.5% for both soil types. Long-term CT reduced intraaggregate porosities and K, within macroaggregates, of the same size fraction, from both the Hoytville silty clay loam and Wooster silt loam soil types. Values for K, of NF aggregates, 5.0 x 10{sup -5} cm s{sup -1}, were reduced 50-fold by long-term CT treatments of the Hoytville series. The K, values through Wooster aggregates from NF, 16.0 x 10{sup -5} cm s{sup -1}, were reduced 80-fold by long-term CT treatments. The K{sub s} values through NF and NT aggregates were positively correlated with their intraaggregate porosities (R{sup 2} = 0.84 for NF and R{sup 2} = 0.45 for NT at P < 0.005). Additional studies are needed to identify rates at which pore geometries within macroaggregates are degraded by CT or improved by NT.

  9. Spatial variability of hydraulic conductivity of an unconfined sandy aquifer determined by a mini slug test

    DEFF Research Database (Denmark)

    Bjerg, Poul Løgstrup; Hinsby, Klaus; Christensen, Thomas Højlund;

    1992-01-01

    The spatial variability of the hydraulic conductivity in a sandy aquifer has been determined by a mini slug test method. The hydraulic conductivity (K) of the aquifer has a geometric mean of 5.05 × 10−4 m s−1, and an overall variance of 1n K equal to 0.37 which corresponds quite well to the results...... obtained by two large scale tracer experiments performed in the aquifer. A geological model of the aquifer based on 31 sediment cores, proposed three hydrogeological layers in the aquifer concurrent with the vertical variations observed with respect to hydraulic conductivity. The horizontal correlation...... length of the hydraulic conductivity has been determined for each of the three hydrogeological layers and is found to be small (1–2.5 m). The asymptotic longitudinal dispersivity of the aquifer has been estimated from the variance in hydraulic conductivity and the horizontal correlation length...

  10. Leaf hydraulic conductance for a tank bromeliad: axial and radial pathways for moving and conserving water.

    Science.gov (United States)

    North, Gretchen B; Lynch, Frank H; Maharaj, Franklin D R; Phillips, Carly A; Woodside, Walter T

    2013-01-01

    Epiphytic plants in the Bromeliaceae known as tank bromeliads essentially lack stems and absorptive roots and instead take up water from reservoirs formed by their overlapping leaf bases. For such plants, leaf hydraulic conductance is plant hydraulic conductance. Their simple strap-shaped leaves and parallel venation make them suitable for modeling leaf hydraulic conductance based on vasculature and other anatomical and morphological traits. Plants of the tank bromeliad Guzmania lingulata were investigated in a lowland tropical forest in Costa Rica and a shaded glasshouse in Los Angeles, CA, USA. Stomatal conductance to water vapor and leaf anatomical variables related to hydraulic conductance were measured for both groups. Tracheid diameters and numbers of vascular bundles (veins) were used with the Hagen-Poiseuille equation to calculate axial hydraulic conductance. Measurements of leaf hydraulic conductance using the evaporative flux method were also made for glasshouse plants. Values for axial conductance and leaf hydraulic conductance were used in a model based on leaky cable theory to estimate the conductance of the radial pathway from the vein to the leaf surface and to assess the relative contributions of both axial and radial pathways. In keeping with low stomatal conductance, low stomatal density, low vein density, and narrow tracheid diameters, leaf hydraulic conductance for G. lingulata was quite low in comparison with most other angiosperms. Using the predicted axial conductance in the leaky cable model, the radial resistance across the leaf mesophyll was predicted to predominate; lower, more realistic values of axial conductance resulted in predicted radial resistances that were closer to axial resistance in their impact on total leaf resistance. Tracer dyes suggested that water uptake through the tank region of the leaf was not limiting. Both dye movement and the leaky cable model indicated that the leaf blade of G. lingulata was structurally and

  11. Comparison of Laboratory and Field Methods for Determining the Quasi-Saturated Hydraulic Conductivity of Soils

    Energy Technology Data Exchange (ETDEWEB)

    Faybishenko, Boris

    1997-08-01

    Laboratory and field ponded infiltration tests in quasi-saturated soils (containing entrapped air) exhibit the same three-stage temporal variability for the flow rate and hydraulic conductivity. However, the values for the hydraulic conductivity may differ by as much as two orders of magnitude due to differences in the geometry and physics of flow when different laboratory and field methods are applied. The purpose of this paper is to investigate this variability using a comparison of results of ponded infiltration tests conducted under laboratory conditions using confined cores, with results of field tests conducted using partially isolated cores and double-ring infiltrometers. Under laboratory conditions in confined cores, during the firs stage, the water flux decreases over time because entrapped air plugs the largest pores in the soils; during the second stage, the quasi-saturated hydraulic conductivity increases by one to two orders of magnitude, essentially reaching the saturated hydraulic conductivity, when entrapped air is discharged from the soils; during the third stage, the hydraulic conductivity decreases to minimum values due to sealing of the soil surface and the effect of biofilms sealing the pores within the wetted zone. Under field conditions, the second stage is only partially developed, and when the surface sealing process begins, the hydraulic pressure drops below the air entry value, thereby causing atmospheric air to enter the soils. As a result, the soils become unsaturated with a low hydraulic conductivity, and the infiltration rate consequently decreases. Contrary to the laboratory experiments in confined cores, the saturated hydraulic conductivity cannot be reached under field conditions. In computations of infiltration one has to take into account the variations in the quasi-saturated and unsaturated hydraulic conductivities, moisture and entrapped air content, and the hydraulic gradient in the quasi-saturated or unsaturated soils.

  12. IN-SERVICE HYDRAULIC CONDUCTIVITY OF GCLS IN LANDFILL COVERS - LABORATORY AND FIELD STUDIES

    Science.gov (United States)

    Laboratory experiments using multi-species inorganic solutions (containing calcium and sodium) were conducted on specimens of a new geosynthetic clay liner (GCL) containing sodium bentonite to determine how cation exchange and desiccation affected the hydraulic conductivity. Calc...

  13. MEASUREMENT OF HYDRAULIC CONDUCTIVITY DISTRIBUTIONS: A MANUAL OF PRACTICE

    Science.gov (United States)

    The ability of hydrologists to perform field measurements of aquifer hydraulic properties must be enhanced in order to significantly improve the capacity to solve groundwater contamination problems at Superfund and other sites. The primary purpose of this manual is to provide ne...

  14. Near-saturated hydraulic conductivity: database development, meta-analysis and pedotransfer functions

    Science.gov (United States)

    Jarvis, Nicholas; Koestel, John; Messing, Ingmar; Lindahl, Anna

    2013-04-01

    Near-saturated hydraulic conductivity exerts a critical control on water flow and solute transport through the vadose zone, yet very little is known concerning how it is influenced by various soil properties and site factors and attributes. Starting from the 1980's, tension infiltrometers or disc permeameters have become an increasingly popular method to measure near-saturated hydraulic conductivity in undisturbed soil. In this presentation, we describe the development and organization of a large database of tension infiltrometer measurements (n>700) collated from the published literature. The raw datasets were standardized and summarized using a modified Kozeny-Carman model of near-saturated hydraulic conductivity (Jarvis, N.J. 2008. Near-saturated hydraulic properties of macroporous soils. Vadose Zone Journal, 7, 1302-1310). This model was found to accurately describe near-saturated conductivity for this large dataset (92% of cases had R2 values larger than 0.9). We will show the results of some initial analyses of the dataset, which show how hydraulic conductivity at pressure heads of -1 and -10 cm, as well as the slope of the near-saturated conductivity function, are affected by: i.) the choice of method to convert unconfined 3D infiltration to hydraulic conductivity, and ii.) interactions between soil properties such as texture and bulk density and site attributes such as land use and climate. We will also present some initial attempts to develop pedotransfer functions for parameters describing near-saturated hydraulic conductivity using the technique of random forests.

  15. Testing hypotheses that link wood anatomy to cavitation resistance and hydraulic conductivity in the genus Acer.

    Science.gov (United States)

    Lens, Frederic; Sperry, John S; Christman, Mairgareth A; Choat, Brendan; Rabaey, David; Jansen, Steven

    2011-05-01

    • Vulnerability to cavitation and conductive efficiency depend on xylem anatomy. We tested a large range of structure-function hypotheses, some for the first time, within a single genus to minimize phylogenetic 'noise' and maximize detection of functionally relevant variation. • This integrative study combined in-depth anatomical observations using light, scanning and transmission electron microscopy of seven Acer taxa, and compared these observations with empirical measures of xylem hydraulics. • Our results reveal a 2 MPa range in species' mean cavitation pressure (MCP). MCP was strongly correlated with intervessel pit structure (membrane thickness and porosity, chamber depth), weakly correlated with pit number per vessel, and not related to pit area per vessel. At the tissue level, there was a strong correlation between MCP and mechanical strength parameters, and some of the first evidence is provided for the functional significance of vessel grouping and thickenings on inner vessel walls. In addition, a strong trade-off was observed between xylem-specific conductivity and MCP. Vessel length and intervessel wall characteristics were implicated in this safety-efficiency trade-off. • Cavitation resistance and hydraulic conductivity in Acer appear to be controlled by a very complex interaction between tissue, vessel network and pit characteristics.

  16. A Self-Consistent Approach for Calculating the Effective Hydraulic Conductivity of a Bimodal, Heterogeneous Medium

    Energy Technology Data Exchange (ETDEWEB)

    Pozdniakov, Sergey; Tsang, Chin-Fu

    2004-01-02

    In this paper, we consider an approach for estimating the effective hydraulic conductivity of a 3D medium with a binary distribution of local hydraulic conductivities. The medium heterogeneity is represented by a combination of matrix medium conductivity with spatially distributed sets of inclusions. Estimation of effective conductivity is based on a self-consistent approach introduced by Shvidler (1985). The tensor of effective hydraulic conductivity is calculated numerically by using a simple system of equations for the main diagonal elements. Verification of the method is done by comparison with theoretical results for special cases and numerical results of Desbarats (1987) and our own numerical modeling. The method was applied to estimating the effective hydraulic conductivity of a 2D and 3D fractured porous medium. The medium heterogeneity is represented by a combination of matrix conductivity and a spatially distributed set of highly conductive fractures. The tensor of effective hydraulic conductivity is calculated for parallel- and random-oriented sets of fractures. The obtained effective conductivity values coincide with Romm's (1966) and Snow's (1969) theories for infinite fracture length. These values are also physically acceptable for the sparsely-fractured-medium case with low fracture spatial density and finite fracture length. Verification of the effective hydraulic conductivity obtained for a fractured porous medium is done by comparison with our own numerical modeling for a 3D case and with Malkovsky and Pek's (1995) results for a 2D case.

  17. Determination of hydraulic conductivity from grain-size distribution for different depositional environments.

    Science.gov (United States)

    Rosas, Jorge; Lopez, Oliver; Missimer, Thomas M; Coulibaly, Kapo M; Dehwah, Abdullah H A; Sesler, Kathryn; Lujan, Luis R; Mantilla, David

    2014-01-01

    Over 400 unlithified sediment samples were collected from four different depositional environments in global locations and the grain-size distribution, porosity, and hydraulic conductivity were measured using standard methods. The measured hydraulic conductivity values were then compared to values calculated using 20 different empirical equations (e.g., Hazen, Carman-Kozeny) commonly used to estimate hydraulic conductivity from grain-size distribution. It was found that most of the hydraulic conductivity values estimated from the empirical equations correlated very poorly to the measured hydraulic conductivity values with errors ranging to over 500%. To improve the empirical estimation methodology, the samples were grouped by depositional environment and subdivided into subgroups based on lithology and mud percentage. The empirical methods were then analyzed to assess which methods best estimated the measured values. Modifications of the empirical equations, including changes to special coefficients and addition of offsets, were made to produce modified equations that considerably improve the hydraulic conductivity estimates from grain size data for beach, dune, offshore marine, and river sediments. Estimated hydraulic conductivity errors were reduced to 6 to 7.1 m/day for the beach subgroups, 3.4 to 7.1 m/day for dune subgroups, and 2.2 to 11 m/day for offshore sediments subgroups. Improvements were made for river environments, but still produced high errors between 13 and 23 m/day.

  18. Determination of hydraulic conductivity from grain-size distribution for different depositional environments

    KAUST Repository

    Rosas, Jorge

    2013-06-06

    Over 400 unlithified sediment samples were collected from four different depositional environments in global locations and the grain-size distribution, porosity, and hydraulic conductivity were measured using standard methods. The measured hydraulic conductivity values were then compared to values calculated using 20 different empirical equations (e.g., Hazen, Carman-Kozeny) commonly used to estimate hydraulic conductivity from grain-size distribution. It was found that most of the hydraulic conductivity values estimated from the empirical equations correlated very poorly to the measured hydraulic conductivity values with errors ranging to over 500%. To improve the empirical estimation methodology, the samples were grouped by depositional environment and subdivided into subgroups based on lithology and mud percentage. The empirical methods were then analyzed to assess which methods best estimated the measured values. Modifications of the empirical equations, including changes to special coefficients and addition of offsets, were made to produce modified equations that considerably improve the hydraulic conductivity estimates from grain size data for beach, dune, offshore marine, and river sediments. Estimated hydraulic conductivity errors were reduced to 6 to 7.1m/day for the beach subgroups, 3.4 to 7.1m/day for dune subgroups, and 2.2 to 11m/day for offshore sediments subgroups. Improvements were made for river environments, but still produced high errors between 13 and 23m/day. © 2013, National Ground Water Association.

  19. Saturated hydraulic conductivity of US soils grouped according textural class and bulk density

    Science.gov (United States)

    Importance of the saturated hydraulic conductivity as soil hydraulic property led to the development of multiple pedotransfer functions for estimating it. One approach to estimating Ksat was using textural classes rather than specific textural fraction contents as pedotransfer inputs. The objective...

  20. Saturated hydraulic conductivity of US soils grouped according to textural class and bulk density

    Science.gov (United States)

    Importance of the saturated hydraulic conductivity as soil hydraulic property led to the development of multiple pedotransfer functions for estimating it. One approach to estimating Ksat was using textural classes rather than specific textural fraction contents as pedotransfer inputs. The objective...

  1. Sample dimensions effect on prediction of soil water retention curve and saturated hydraulic conductivity

    Science.gov (United States)

    Soil water retention curve (SWRC) and saturated hydraulic conductivity (SHC) are key hydraulic properties for unsaturated zone hydrology and groundwater. Not only are the SWRC and SHC measurements time-consuming, their results are scale dependent. Although prediction of the SWRC and SHC from availab...

  2. Prediction of spatially variable unsaturated hydraulic conductivity using scaled particle-size distribution functions

    NARCIS (Netherlands)

    Nasta, P.; Romano, N.; Assouline, S; Vrugt, J.A.; Hopmans, J.W.

    2013-01-01

    Simultaneous scaling of soil water retention and hydraulic conductivity functions provides an effective means to characterize the heterogeneity and spatial variability of soil hydraulic properties in a given study area. The statistical significance of this approach largely depends on the number of s

  3. Hydraulic Tomography and High-Resolution Slug Testing to Determine Hydraulic Conductivity Distributions - Year 1

    Science.gov (United States)

    2005-12-01

    the addition into a well of a known volume of water or a physical slug. More recently, pneumatic methods have become popular ( Zemansky and McElwee...and Zemansky , 2000), (Sellwood, 2001) and (Ross, 2004)]. The aquifer material at GEMS exhibits linear and non-linear responses to slug testing...1976; Zurbuchen et al., 2002; and Zemansky and McElwee, 2005). Slug tests have been a common method for obtaining information about the hydraulic

  4. Hamiltonian Monte Carlo algorithm for the characterization of hydraulic conductivity from the heat tracing data

    Science.gov (United States)

    Djibrilla Saley, A.; Jardani, A.; Soueid Ahmed, A.; Raphael, A.; Dupont, J. P.

    2016-11-01

    Estimating spatial distributions of the hydraulic conductivity in heterogeneous aquifers has always been an important and challenging task in hydrology. Generally, the hydraulic conductivity field is determined from hydraulic head or pressure measurements. In the present study, we propose to use temperature data as source of information for characterizing the spatial distributions of the hydraulic conductivity field. In this way, we performed a laboratory sandbox experiment with the aim of imaging the heterogeneities of the hydraulic conductivity field from thermal monitoring. During the laboratory experiment, we injected a hot water pulse, which induces a heat plume motion into the sandbox. The induced plume was followed by a set of thermocouples placed in the sandbox. After the temperature data acquisition, we performed a hydraulic tomography using the stochastic Hybrid Monte Carlo approach, also called the Hamiltonian Monte Carlo (HMC) algorithm to invert the temperature data. This algorithm is based on a combination of the Metropolis Monte Carlo method and the Hamiltonian dynamics approach. The parameterization of the inverse problem was done with the Karhunen-Loève (KL) expansion to reduce the dimensionality of the unknown parameters. Our approach has provided successful reconstruction of the hydraulic conductivity field with low computational effort.

  5. Effects of hedgerow systems on soil moisture and unsaturated hydraulics conductivity measured by the Libardi method

    Directory of Open Access Journals (Sweden)

    S . Prijono

    2016-01-01

    Full Text Available The hedgerow systems are the agroforestry practices suggesting any positive impacts and negative impacts on soil characteristics. This study evaluated the effects of hedgerows on the unsaturated hydraulic conductivity of soil with the Libardi method approach. This study was conducted in North Lampung for 3 months on the hedgerow plots of Peltophorum dassyrachis (P, Gliricidia sepium (G, and without hedgerow plot (K, with four replications. Each plot was watered as much as 150 liters of water until saturated, then the soil surface were covered with the plastic film. Observation of soil moisture content was done to a depth of 70 cm by the 10 cm intervals. Soil moisture content was measured using the Neutron probe that was calibrated to get the value of volumetric water content. Unsaturated hydraulic conductivity of soil was calculated by using the Libardi Equation. Data were tested using the analysis of variance, the least significant different test (LSD, Duncan Multiple Range Test (DMRT, correlation and regression analysis. The results showed that the hedgerow significantly affected the soil moisture content and unsaturated hydraulic conductivity. Soil moisture content on the hedgerow plots was lower than the control plots. The value of unsaturated hydraulic conductivity in the hedgerow plots was higher than the control plots. Different types of hedgerows affected the soil moisture content and unsaturated hydraulic conductivity. The positive correlation was found between the volumetric soil moisture content and the unsaturated hydraulic conductivity of soil.

  6. The Comparison of Predicted and Measured Hydraulic Conductivities of Soils having Different Physical Properties

    Science.gov (United States)

    Zengin, Enes; Abiddin Erguler, Zeynal; Karakuş, Hüseyin

    2015-04-01

    Hydraulic conductivity is one of the most important parameter of earth science related studies such as engineering geology, soil physics, agriculture etc. In order to estimate the ability of soils to transport fluid through particles, field and laboratory tests have been performed since last decades of 19th century. Constant and falling head tests are widely used to directly measure hydraulic conductivity values in laboratory conditions for soils having different particle size distributions. The determination of hydraulic conductivity of soils by performing these methods are time consuming processes and also requires undisturbed samples to reflect in-situ natural condition. Considering these limitations, numerous approaches have been proposed to practically estimate hydraulic conductivity of soils by utilizing empirical equations based on simple physical and index properties such as grain size distribution curves related parameters, porosity, void ratio, etc. Many previous studies show that the hydraulic conductivity values calculated by empirical equations deviate more than two order magnitude than the measured hydraulic conductivity values obtained from convenient permeability tests. In order to investigate the main controlling parameters on hydraulic conductivity of soils, a comprehensive research program was carried out on some disturbed and undisturbed soil samples collected from different locations in Turkey. The hydraulic conductivity values of samples were determined as changing between 10-6 and 10-9 m/s by using falling head tests. In addition to these tests, basic soil properties such as natural water content, Atterberg limits, specific gravity and grain size analyses of these samples were also defined to be used as an input parameters of empirical equations for prediction hydraulic conductivity values. In addition, data from previous studies were also used for the aim of this study. The measured hydraulic conductivity values were correlated with all

  7. The relationship between hydraulic conductivity and diffusion in granitic rock matrix

    Science.gov (United States)

    Najser, J.; Gvozdik, L.; Havlova, V.; Sosna, K.; Vecernik, P.; Zaruba, J.

    2012-12-01

    In the Czech Republic, granite is being considered as the host rock for a radioactive waste repository. The aim of the current research project is to study of the hydraulic properties of the low-permeable rock matrix. 45 granitic samples from ten sites have been subjected to hydraulic conductivity (K) and diffusivity (De) tests. Hydraulic conductivity was measured in pressure cells. A constant pressure difference of Δ = 50 kPa was applied by pressure controllers and the volume of water that passed through the sample was recorded. The effective diffusion coefficient De was measured using 3H tracer in through-diffusion experiments. The activities in both input and output reservoirs were regularly monitored using liquid scintillation spectrometry. The hydraulic conductivities of fresh granite varied from 1.65 x 10-10 to 1 x 10-14 m.s-1 while the effective diffusion coefficient ranged from 7.4 x 10-12 to 4 x 10-13 m2.s-1. Comparison of measured "K" and "De" values reveals significant scatter, despite clear trends. Numerical simulation of both hydraulic conductivity and diffusivity was undertaken using finite-element code NAPSAC. The results show that reduced microcrack length influences the connectivity of the microcrack network, increases diffusivity, and decreases hydraulic conductivity. The imperfect correlation between experimental "K" and "De" is explained by the different geometries of the microcrack networks within the studied granites.

  8. Getting saturated hydraulic conductivity from surface Ground-Penetrating Radar measurements inside a ring infiltrometer

    Science.gov (United States)

    Leger, E.; Saintenoy, A.; Coquet, Y.

    2013-12-01

    Hydraulic properties of soils, described by the soil water retention and hydraulic conductivity functions, strongly influence water flow in the vadoze zone, as well as the partitioning of precipitation between infiltration into the soil and runoff along the ground surface. Their evaluation has important applications for modelling available water resources and for flood forecasting. It is also crucial to evaluate soil's capacity to retain chemical pollutants and to assess the potential of groundwater pollution. The determination of the parameters involved in soil water retention functions, 5 parameters when using the van Genuchten function, is usually done by laboratory experiments, such as the water hanging column. Hydraulic conductivity, on the other hand can be estimated either in laboratory, or in situ using infiltrometry tests. Among the large panel of existing tests, the single or double ring infiltrometers give the field saturated hydraulic conductivity by applying a positive charge on soils, whereas the disk infiltrometer allows to reconstruct the whole hydraulic conductivity curve, by applying different charges smaller than or equal to zero. In their classical use, volume of infiltrated water versus time are fitted to infer soil's hydraulic conductivity close to water saturation. Those tests are time-consuming and difficult to apply to landscape-scale forecasting of infiltration. Furthermore they involve many assumptions concerning the form of the infiltration bulb and its evolution. Ground-Penetrating Radar (GPR) is a geophysical method based on electromagnetic wave propagation. It is highly sensitive to water content variations directly related to the dielectric permittivity. In this study GPR was used to monitor water infiltration inside a ring infiltrometer and retrieve the saturated hydraulic conductivity. We carried out experiments in a quarry of Fontainebleau sand, using a Mala RAMAC system with antennae centered on 1600 MHz. We recorded traces at

  9. Effects of leachate infiltration and desiccation cracks on hydraulic conductivity of compacted clay

    Directory of Open Access Journals (Sweden)

    Jun HE

    2015-04-01

    Full Text Available Both cracks in clay liner and the complex composition of landfill leachate might have effects on the hydraulic conductivity of a compacted clay liner. In this study, the hydraulic conductivities of natural clay and bentonite-modified clay with and without desiccation cracks were measured, respectively, using three types of liquids as permeating liquid: 2 500 mg/L acetic acid solution, 0.5 mol/L CaCl2 solution, and tap water. When tap water was adopted as the permeating liquid, desiccation cracks resulted in increases in the average value of hydraulic conductivity: a 25-fold increase for the natural clay and a 5.7-fold increase for the bentonite-modified clay. It was also found out that the strong self-healing capability of bentonite helped to reduce the adverse impact of cracks on hydraulic performance. In contrast to tap water, simulated leachates (acetic acid and CaCl2 solutions show no adverse effect on the hydraulic conductivities of natural and bentonite-modified clays. It is concluded that desiccation cracks and bentonite have more significant effects on hydraulic performance than simulated leachates.

  10. Analysis of Grain Size Distribution and Hydraulic Conductivity for a Variety of Sediment Types with Application to Wadi Sediments

    KAUST Repository

    Rosas Aguilar, Jorge

    2013-05-01

    Grain size distribution, porosity, and hydraulic conductivity from over 400 unlithified sediment samples were analized. The measured hydraulic conductivity values were then compared to values calculated using 20 different empirical equations commonly used to estimate hydraulic conductivity from grain size analyses. It was found that most of the hydraulic conductivity values estimated from the empirical equations correlated very poorly to the measured hydraulic conductivity values. Modifications of the empirical equations, including changes to special coefficients and statistical off sets, were made to produce modified equations that considerably improve the hydraulic conductivity estimates from grain size data for beach, dune, off shore marine, and wadi sediments. Expected hydraulic conductivity estimation errors were reduced. Correction factors were proposed for wadi sediments, taking mud percentage and the standard deviation (in phi units) into account.

  11. Improving prediction of hydraulic conductivity by constraining capillary bundle models to a maximum pore size

    Science.gov (United States)

    Iden, Sascha; Peters, Andre; Durner, Wolfgang

    2017-04-01

    Soil hydraulic properties are required to solve the Richards equation, the most widely applied model for variably-saturated flow. While the experimental determination of the water retention curve does not pose significant challenges, the measurement of unsaturated hydraulic conductivity is time consuming and costly. The prediction of the unsaturated hydraulic conductivity curve from the soil water retention curve by pore-bundle models is a cost-effective and widely applied technique. A well-known problem of conductivity prediction for retention functions with wide pore-size distributions is the sharp drop in conductivity close to water saturation. This problematic behavior is well known for the van Genuchten model if the shape parameter n assumes values smaller than about 1.3. So far, the workaround for this artefact has been to introduce an explicit air-entry value into the capillary saturation function. However, this correction leads to a retention function which is not continuously differentiable and thus a discontinuous water capacity function. We present an improved parametrization of the hydraulic properties which uses the original capillary saturation function and introduces a maximum pore radius only in the pore-bundle model. Closed-form equations for the hydraulic conductivity function were derived for the unimodal and multimodal retention functions of van Genuchten and have been tested by sensitivity analysis and applied in curve fitting and inverse modeling of multistep outflow experiments. The resulting hydraulic conductivity function is smooth, increases monotonically close to saturation, and eliminates the sharp drop in conductivity close to saturation. Furthermore, the new model retains the smoothness and continuous differentiability of the water retention curve. We conclude that the resulting soil hydraulic functions are physically more reasonable than the ones predicted by previous approaches, and are thus ideally suited for numerical simulations

  12. Evaluation of Regression and Neuro_Fuzzy Models in Estimating Saturated Hydraulic Conductivity

    Directory of Open Access Journals (Sweden)

    J. Behmanesh

    2015-06-01

    Full Text Available Study of soil hydraulic properties such as saturated and unsaturated hydraulic conductivity is required in the environmental investigations. Despite numerous research, measuring saturated hydraulic conductivity using by direct methods are still costly, time consuming and professional. Therefore estimating saturated hydraulic conductivity using rapid and low cost methods such as pedo-transfer functions with acceptable accuracy was developed. The purpose of this research was to compare and evaluate 11 pedo-transfer functions and Adaptive Neuro-Fuzzy Inference System (ANFIS to estimate saturated hydraulic conductivity of soil. In this direct, saturated hydraulic conductivity and physical properties in 40 points of Urmia were calculated. The soil excavated was used in the lab to determine its easily accessible parameters. The results showed that among existing models, Aimrun et al model had the best estimation for soil saturated hydraulic conductivity. For mentioned model, the Root Mean Square Error and Mean Absolute Error parameters were 0.174 and 0.028 m/day respectively. The results of the present research, emphasises the importance of effective porosity application as an important accessible parameter in accuracy of pedo-transfer functions. sand and silt percent, bulk density and soil particle density were selected to apply in 561 ANFIS models. In training phase of best ANFIS model, the R2 and RMSE were calculated 1 and 1.2×10-7 respectively. These amounts in the test phase were 0.98 and 0.0006 respectively. Comparison of regression and ANFIS models showed that the ANFIS model had better results than regression functions. Also Nuro-Fuzzy Inference System had capability to estimatae with high accuracy in various soil textures.

  13. Using boosted regression trees to predict the near-saturated hydraulic conductivity of undisturbed soils

    Science.gov (United States)

    Koestel, John; Bechtold, Michel; Jorda, Helena; Jarvis, Nicholas

    2015-04-01

    The saturated and near-saturated hydraulic conductivity of soil is of key importance for modelling water and solute fluxes in the vadose zone. Hydraulic conductivity measurements are cumbersome at the Darcy scale and practically impossible at larger scales where water and solute transport models are mostly applied. Hydraulic conductivity must therefore be estimated from proxy variables. Such pedotransfer functions are known to work decently well for e.g. water retention curves but rather poorly for near-saturated and saturated hydraulic conductivities. Recently, Weynants et al. (2009, Revisiting Vereecken pedotransfer functions: Introducing a closed-form hydraulic model. Vadose Zone Journal, 8, 86-95) reported a coefficients of determination of 0.25 (validation with an independent data set) for the saturated hydraulic conductivity from lab-measurements of Belgian soil samples. In our study, we trained boosted regression trees on a global meta-database containing tension-disk infiltrometer data (see Jarvis et al. 2013. Influence of soil, land use and climatic factors on the hydraulic conductivity of soil. Hydrology & Earth System Sciences, 17, 5185-5195) to predict the saturated hydraulic conductivity (Ks) and the conductivity at a tension of 10 cm (K10). We found coefficients of determination of 0.39 and 0.62 under a simple 10-fold cross-validation for Ks and K10. When carrying out the validation folded over the data-sources, i.e. the source publications, we found that the corresponding coefficients of determination reduced to 0.15 and 0.36, respectively. We conclude that the stricter source-wise cross-validation should be applied in future pedotransfer studies to prevent overly optimistic validation results. The boosted regression trees also allowed for an investigation of relevant predictors for estimating the near-saturated hydraulic conductivity. We found that land use and bulk density were most important to predict Ks. We also observed that Ks is large in fine

  14. Hydraulic conductivity study of compacted clay soils used as landfill liners for an acidic waste.

    Science.gov (United States)

    Hamdi, Noureddine; Srasra, Ezzeddine

    2013-01-01

    Three natural clayey soils from Tunisia were studied to assess their suitability for use as a liner for an acid waste disposal site. An investigation of the effect of the mineral composition and mechanical compaction on the hydraulic conductivity and fluoride and phosphate removal of three different soils is presented. The hydraulic conductivity of these three natural soils are 8.5 × 10(-10), 2.08 × 10(-9) and 6.8 × 10(-10)m/s for soil-1, soil-2 and soil-3, respectively. Soil specimens were compacted under various compaction strains in order to obtain three wet densities (1850, 1950 and 2050 kg/m(3)). In this condition, the hydraulic conductivity (k) was reduced with increasing density of sample for all soils. The test results of hydraulic conductivity at long-term (>200 days) using acidic waste solution (pH=2.7, charged with fluoride and phosphate ions) shows a decrease in k with time only for natural soil-1 and soil-2. However, the specimens of soil-2 compressed to the two highest densities (1950 and 2050 kg/m(3)) are cracked after 60 and 20 days, respectively, of hydraulic conductivity testing. This damage is the result of a continued increase in the internal stress due to the swelling and to the effect of aggressive wastewater. The analysis of anions shows that the retention of fluoride is higher compared to phosphate and soil-1 has the highest sorption capacity.

  15. Aerenchyma Formed Under Phosphorus Deficiency Contributes to the Reduced Root Hydraulic Conductivity in Maize Roots

    Institute of Scientific and Technical Information of China (English)

    Mingshou Fan; Ruiqin Bai; Xuefeng Zhao; Jianhua Zhang

    2007-01-01

    Root hydraulic conductivity has been shown to decrease under phosphorus (P) deficiency. This study investigated how the formation of aerenchyma is related to this change. Root anatomy, as well as root hydraulic conductivity was studied in maize (Zea mays L.) roots under different phosphorus nutrition conditions. Plant roots under P stress showed enhanced degradation of cortical cells and the aerenchyma formation was associated with their reduced root hydraulic conductivity, supporting our hypothesis that air spaces that form in the cortex of phosphorusstressed roots impede the radial transport of water in a root cylinder. Further evidence came from the variation in aerenchyma formation due to genotypic differences. Five maize inbred lines with different porosity in their root cortex showed a significant negative correlation with their root hydraulic conductivity. Shoot relative water content was also found lower in P-deficient maize plants than that in P-sufficient ones when such treatment was prolonged enough, suggesting a limitation of water transport due to lowered root hydraulic conductivity of P-deficient piants.

  16. Test of the rosetta pedotransfer function for saturated hydraulic conductivity

    NARCIS (Netherlands)

    Alvarez-Acosta, C.; Lascano, R.J.; Stroosnijder, L.

    2012-01-01

    Simulation models are tools that can be used to explore, for example, effects of cultural practices on soil erosion and irrigation on crop yield. However, often these models require many soil related input data of which the saturated hy- draulic conductivity (Ks) is one of the most important ones. T

  17. Anomalous electronic conductance in quasicrystals

    Science.gov (United States)

    Roche, Stephan; Moulopoulos, Konstantinos

    2000-03-01

    Subtle quantum interference effects in one-dimensional quasicrystals are reported. Quite opposite to their metallic counterparts, quasiperiodic systems are shown to exhibit interesting variations of their conducting properties upon disruption of their long-range order. A sudden phason change in the structure leads to a series of transitions that proceed from extremely simple and regular to highly complex self-similar resistive patterns.

  18. Hydraulic Conductivity Estimate via Tracer Test and Ensemble Kalman Filter Data Assimilation: Theoretical and Numerical Fundamentals

    Science.gov (United States)

    Crestani, E.; Camporese, M.; Salandin, P.

    2011-12-01

    Hydraulic properties of natural aquifers, such as porosity, hydraulic conductivity, and storativity, exhibit an erratic spatial variability at different scales that is difficult to recognize without expensive in situ sampling campaigns, laboratory analyses, and, when available, spatially distributed pumping tests. Nevertheless, the importance of the heterogeneous structure of natural formations on solute transport is well recognized, being the non-Fickian evolution of contaminant plumes and the relevant dispersive phenomena controlled by the variability of the hydraulic conductivity K at the local scale. Tracer test analyses have been widely adopted to identify the complex distribution of in situ hydraulic properties. In particular, the use of geophysical methods like the borehole Electrical Resistivity Tomography (ERT) have been in rapid increase, due to their potential to accurately describe the spatio-temporal evolution of the injected solute. Under the assumptions that the solute spreads as a passive tracer and with high values of the Peclet number, the plume evolution is controlled by the porosity and the spatial distribution of hydraulic conductivity. Combining the Lagrangian formulation of transport and the ensemble Kalman filter (EnKF) data assimilation technique, the purpose of this study is to infer the spatial distribution of K at the local scale from a sequence of time-lapse concentration imaging. The capabilities of the proposed approach are investigated simulating various assimilation experiments via synthetic tracer tests in a three-dimensional finite domain reproducing a heterogeneous aquifer. In a first scenario, all the available concentration measurements are assimilated and the entire hydraulic conductivity field is updated, while in the remaining scenarios the K values are updated only in a limited number of nodes by assimilating the concentrations in these same nodes, the hydraulic conductivity in the rest of the domain being the result of a

  19. STOCHASTIC ANALYSIS OF UNSATURATED FLOW WITH THE NORMAL DISTRIBUTION OF SOIL HYDRAULIC CONDUCTIVITY

    Institute of Scientific and Technical Information of China (English)

    Huang Guan-hua; Zhang Ren-duo

    2003-01-01

    Stochastic approaches are useful to quantitatively describe transport behavior over large temporal and spatial scales while accounting for the influence of small-scale variabilities. Numerous solutions have been developed for unsaturated soil water flow based on the lognormal distribution of soil hydraulic conductivity. To our knowledge, no available stochastic solutions for unsaturated flow have been derived on the basis of the normal distribution of hydraulic conductivity. In this paper, stochastic solutions were developed for unsaturated flow by assuming the normal distribution of saturated hydraulic conductivity (Ks). Under the assumption that soil hydraulic properties are second-order stationary, analytical expressions for capillary tension head variance (σ2h) and effective hydraulic conductivity (K*ii) in stratified soils were derived using the perturbation method. The dependence of σ2h and K*ii on soil variability and mean flow variables (the mean capillary tension head and its temporal and spatial gradients) and mean flow conditions (wetting and drying) were systematically analyzed. The calculated variance of capillary tension head with the analytical solution derived in this paper was compared with field experimental data. The good agreement indicates that the analytical solution is applicable to evaluate the variance of capillary tension head of field soils with moderate variability.

  20. Scaling of material properties for Yucca Mountain: literature review and numerical experiments on saturated hydraulic conductivity

    Energy Technology Data Exchange (ETDEWEB)

    McKenna, S.A.; Rautman, C.A.

    1996-08-01

    A review of pertinent literature reveals techniques which may be practical for upscaling saturated hydraulic conductivity at Yucca Mountain: geometric mean, spatial averaging, inverse numerical modeling, renormalization, and a perturbation technique. Isotropic realizations of log hydraulic conductivity exhibiting various spatial correlation lengths are scaled from the point values to five discrete scales through these techniques. For the variances in log{sub 10} saturated hydraulic conductivity examined here, geometric mean, numerical inverse and renormalization adequately reproduce point scale fluxes across the modeled domains. Fastest particle velocities and dispersion measured on the point scale are not reproduced by the upscaled fields. Additional numerical experiments examine the utility of power law averaging on a geostatistical realization of a cross-section similar to the cross-sections that will be used in the 1995 groundwater travel time calculations. A literature review on scaling techniques for thermal and mechanical properties is included. 153 refs., 29 figs., 6 tabs.

  1. Method for estimating spatially variable seepage loss and hydraulic conductivity in intermittent and ephemeral streams

    Science.gov (United States)

    Niswonger, R.G.; Prudic, D.E.; Fogg, G.E.; Stonestrom, D.A.; Buckland, E.M.

    2008-01-01

    A method is presented for estimating seepage loss and streambed hydraulic conductivity along intermittent and ephemeral streams using streamflow front velocities in initially dry channels. The method uses the kinematic wave equation for routing streamflow in channels coupled to Philip's equation for infiltration. The coupled model considers variations in seepage loss both across and along the channel. Water redistribution in the unsaturated zone is also represented in the model. Sensitivity of the streamflow front velocity to parameters used for calculating seepage loss and for routing streamflow shows that the streambed hydraulic conductivity has the greatest sensitivity for moderate to large seepage loss rates. Channel roughness, geometry, and slope are most important for low seepage loss rates; however, streambed hydraulic conductivity is still important for values greater than 0.008 m/d. Two example applications are presented to demonstrate the utility of the method. Copyright 2008 by the American Geophysical Union.

  2. Gas diffusion-derived tortuosity governs saturated hydraulic conductivity in sandy soils

    DEFF Research Database (Denmark)

    Masis Melendez, Federico; Deepagoda Thuduwe Kankanamge Kelum, Chamindu; de Jonge, Lis Wollesen

    2014-01-01

    Accurate prediction of saturated hydraulic conductivity (Ksat) is essential for the development of better distributed hydrological models and area-differentiated risk assessment of chemical leaching. The saturated hydraulic conductivity is often estimated from basic soil properties such as particle...... size distribution or, more recently, soil-air permeability. However, similar links to soil gas diffusivity (Dp/Do) have not been fully explored even though gas diffusivity is a direct measure of connectivity and tortuosity of the soil pore network. Based on measurements for a coarse sandy soil....../Do model to measured data, and subsequently linked to the cementation exponent of the wellestablished Revil and Cathles predictive model for saturated hydraulic conductivity. Furthermore, a two-parameter model, analogue to the Kozeny-Carman equation, was developed for the Ksat - Dp/Do relationships. All 44...

  3. Hydraulic conductivity in response to exchangeable sodium percentage and solution salt concentration

    Directory of Open Access Journals (Sweden)

    Jefferson Luiz de Aguiar Paes

    2014-10-01

    Full Text Available Hydraulic conductivity is determined in laboratory assays to estimate the flow of water in saturated soils. However, the results of this analysis, when using distilled or deionized water, may not correspond to field conditions in soils with high concentrations of soluble salts. This study therefore set out to determine the hydraulic conductivity in laboratory conditions using solutions of different electrical conductivities in six soils representative of the State of Pernambuco, with the exchangeable sodium percentage adjusted in the range of 5-30%. The results showed an increase in hydraulic conductivity with both decreasing exchangeable sodium percentage and increasing electrical conductivity in the solution. The response to the treatments was more pronounced in soils with higher proportion of more active clays. Determination of hydraulic conductivity in laboratory is routinely performed with deionized or distilled water. However, in salt affected soils, these determinations should be carried out using solutions of electrical conductivity different from 0 dS m-1, with values close to those determined in the saturation extracts.

  4. Evaluation of actual and estimated hydraulic conductivity of sands with different gradation and shape.

    Science.gov (United States)

    Cabalar, Ali Firat; Akbulut, Nurullah

    2016-01-01

    Hydraulic conductivities of sands with different gradation and grain shape were estimated experimentally at a relative density (Dr) of about 40 % and a 22 ± 2 °C of constant temperature. Narli Sand (NS) with 0.67 of sphericity (S) and 0.72 of roundness (R), and Crushed Stone Sand (CSS) with 0.55 of S and 0.15 of R values were artificially graded into sixteen different grain-size fractions (4.75-2, 2-1.18, 1.18-0.6, 0.6-0.425, 0.425-0.3, 0.3-0.075, 4.75-0.075, 2-0.075, 1.18-0.075, 0.6-0.075, 0.425-0.075, 4.75-0.6, 2-0.6, 4.75-0.425, 2-0.425, 1.18-0.425 mm). Hydraulic conductivities of the NS estimated by use of constant head test ranged from 1.61 to 0.01 cm/s, whilst those of the CSS estimated by the same test ranged from 2.45 to 0.012 cm/s. It was observed that the hydraulic conductivity values of the NS are lower than those of the CSS samples, which is likely to be the result of differences in shape, particularly in R values. The results clearly demonstrated that the hydraulic conductivity can be significantly influenced by grading characteristics (d10, d20, d30, d50, d60, cu, cc, n, Io). Furthermore, comparisons between results obtained in the present study and hydraulic conductivity estimated with other formulas available in the literature were made. The comparisons indicated that the best estimation of hydraulic conductivity changes based on the gradation and shape properties of the sands tested.

  5. Steady state method to determine unsaturated hydraulic conductivity at the ambient water potential

    Science.gov (United States)

    HUbbell, Joel M.

    2014-08-19

    The present invention relates to a new laboratory apparatus for measuring the unsaturated hydraulic conductivity at a single water potential. One or more embodiments of the invented apparatus can be used over a wide range of water potential values within the tensiometric range, requires minimal laboratory preparation, and operates unattended for extended periods with minimal supervision. The present invention relates to a new laboratory apparatus for measuring the unsaturated hydraulic conductivity at a single water potential. One or more embodiments of the invented apparatus can be used over a wide range of water potential values within the tensiometric range, requires minimal laboratory preparation, and operates unattended for extended periods with minimal supervision.

  6. Field experiments in a fractured clay till. 1. Hydraulic conductivity and fracture aperture

    Science.gov (United States)

    McKay, Larry D.; Cherry, John A.; Gillham, Robert W.

    1993-04-01

    Field values of horizontal hydraulic conductivity measured in the upper 1.5-5.5 m of a weathered and fractured clay-rich till were strongly influenced by smearing around piezometer intakes, which occurs during augering, and by the physical scale of the measuring device. Values measured in conventional augered piezometers were typically 1-2 orders of magnitude lower than those measured in piezometers designed to reduce smearing. Measurements of hydraulic conductivity in small-scale seepage collectors or piezometers, which typically intersect fewer than 10 fractures, vary over a much greater range, 10-10 to 10-6 m/s, than large-scale values based on infiltration into 5.5-m-deep trenches which intersect thousands of fractures (range 10-7 to 3×10-7 m/s). Values of hydraulic fracture aperture, 1-43 μm, and fracture porosity, 3×10-5 to 2×10-3, were calculated using the cubic law with fracture orientation/distribution measurements and the small-scale hydraulic conductivity measurements. This paper provides the first reliable determination of the magnitude and spatial distribution of hydraulically derived fracture parameters in a clay deposit. The absence of such data has, until now, severely limited the application of quantitative groundwater flow and contaminant transport models in this type of deposit.

  7. Light response of hydraulic conductance in bur oak (Quercus macrocarpa) leaves.

    Science.gov (United States)

    Voicu, Mihaela C; Zwiazek, Janusz J; Tyree, Melvin T

    2008-07-01

    A four- to seven-fold enhancement of leaf hydraulic conductance by light has been reported in three temperate tree species. The enhancement occurs in the liquid-flow pathway between the petiole and the site of water evaporation. The enhancement occurs within 1 h, and dissipates in darkness over a period of 1 to 10 h depending on species. Here we report light-induced enhancement of leaf hydraulic conductance in a fourth species, bur oak (Quercus macrocarpa Michx.), the dependence of the effect on light flux and color, its absence in leaves of seedlings, and the impact on the response of leaf vein severance and several metabolic inhibitors. The light response of leaf hydraulic conductance approached saturation at a photosynthetic photon flux of 150 mumol m(-2) s(-1). Hydraulic enhancement was greater in response to blue and green light than to visible radiation of longer wavelengths, although at the same irradiance, the response to white light was greater than to light of any single color. Atrazine (a photosystem II inhibitor), fusicoccin (which stimulates plasma membrane-bound H(+)-ATPase) and HgCl(2) (an aquaporin blocker) reduced the light response of leaf lamina hydraulic conductance. When 2-mercaptoethanol was added following mercury treatment, the light response was totally suppressed. Our results are consistent with the notion that the effect of light on leaf lamina hydraulic conductance is controlled by factors acting outside the leaf veins, possibly through light-induced changes in membrane permeability of either mesophyll or bundle sheath cells, or both.

  8. Crystal fields and conduction electrons in praseodymium

    DEFF Research Database (Denmark)

    Clausen, K.N.; Aagaard Sørensen, S.; McEwen, K.A.

    1995-01-01

    The interactions between the crystal-field excitations, the phonons and the conduction electrons in Pr have been studied further. The low-energy satellites to the crystal-field excitations, which are believed to be associated with propagating paramagnon modes in the conduction-electron gas, appear...

  9. Averaging hydraulic head, pressure head, and gravitational head in subsurface hydrology, and implications for averaged fluxes, and hydraulic conductivity

    Directory of Open Access Journals (Sweden)

    G. H. de Rooij

    2009-07-01

    Full Text Available Current theories for water flow in porous media are valid for scales much smaller than those at which problem of public interest manifest themselves. This provides a drive for upscaled flow equations with their associated upscaled parameters. Upscaling is often achieved through volume averaging, but the solution to the resulting closure problem imposes severe restrictions to the flow conditions that limit the practical applicability. Here, the derivation of a closed expression of the effective hydraulic conductivity is forfeited to circumvent the closure problem. Thus, more limited but practical results can be derived. At the Representative Elementary Volume scale and larger scales, the gravitational potential and fluid pressure are treated as additive potentials. The necessary requirement that the superposition be maintained across scales is combined with conservation of energy during volume integration to establish consistent upscaling equations for the various heads. The power of these upscaling equations is demonstrated by the derivation of upscaled water content-matric head relationships and the resolution of an apparent paradox reported in the literature that is shown to have arisen from a violation of the superposition principle. Applying the upscaling procedure to Darcy's Law leads to the general definition of an upscaled hydraulic conductivity. By examining this definition in detail for porous media with different degrees of heterogeneity, a series of criteria is derived that must be satisfied for Darcy's Law to remain valid at a larger scale.

  10. Using Electronic Mail to Conduct Survey Research.

    Science.gov (United States)

    Thach, Liz

    1995-01-01

    Describes public and private online networks and the characteristics of electronic mail. Reviews the literature on survey research conducted via electronic mail, and examines the issues of design, implementation, and response. A table displays advantages and disadvantages of electronic mail surveys. (AEF)

  11. A wilty mutant of rice has impaired hydraulic conductance.

    Science.gov (United States)

    Koizumi, Koji; Ookawa, Taiichiro; Satoh, Hikaru; Hirasawa, Tadashi

    2007-08-01

    The rice CM2088 mutant is the wilty phenotype and wilts markedly under well-watered sunny conditions. The leaf water potential and epidermal (mainly stomatal) conductance of CM2088 plants decreased significantly under conditions that induced intense transpiration, as compared with those of wild-type plants, revealing that the wilty phenotype was not the result of abnormal stomatal behavior but was due to an increase in resistance to water transport. The resistance to water transport was dramatically elevated in the node and the sheath and blade of a leaf of the mutant, but not in the root or stem. The diameter of xylem vessels in the large vascular bundles of the leaf sheath and the internode tended to be small, and the numbers of vessel elements with narrowed or scalariform perforation plates in the leaf blade and sheath were greater in the mutant than in the wild type. Most xylem vessels were occluded, with air bubbles in the leaf sheath of the mutant during the midday hours under intense transpiration conditions, while no bubbles were observed in plants that were barely transpiring, revealing that the significant increase in resistance to water transport was a result of the cavitation. The additive effects of cavitation in xylem vessels and the decreased diameter and deformed plates of vessel elements might be responsible for the wilty phenotype of CM2088.

  12. The Electronic Thermal Conductivity of Graphene.

    Science.gov (United States)

    Kim, Tae Yun; Park, Cheol-Hwan; Marzari, Nicola

    2016-04-13

    Graphene, as a semimetal with the largest known thermal conductivity, is an ideal system to study the interplay between electronic and lattice contributions to thermal transport. While the total electrical and thermal conductivity have been extensively investigated, a detailed first-principles study of its electronic thermal conductivity is still missing. Here, we first characterize the electron-phonon intrinsic contribution to the electronic thermal resistivity of graphene as a function of doping using electronic and phonon dispersions and electron-phonon couplings calculated from first-principles at the level of density-functional theory and many-body perturbation theory (GW). Then, we include extrinsic electron-impurity scattering using low-temperature experimental estimates. Under these conditions, we find that the in-plane electronic thermal conductivity κe of doped graphene is ∼300 W/mK at room temperature, independently of doping. This result is much larger than expected and comparable to the total thermal conductivity of typical metals, contributing ∼10% to the total thermal conductivity of bulk graphene. Notably, in samples whose physical or domain sizes are of the order of few micrometers or smaller, the relative contribution coming from the electronic thermal conductivity is more important than in the bulk limit, because lattice thermal conductivity is much more sensitive to sample or grain size at these scales. Last, when electron-impurity scattering effects are included we find that the electronic thermal conductivity is reduced by 30 to 70%. We also find that the Wiedemann-Franz law is broadly satisfied at low and high temperatures but with the largest deviations of 20-50% around room temperature.

  13. Natural Attenuation of Fuel Hydrocarbon Contaminants:Correlation of Biodegradation with Hydraulic Conductivity in a Field Case Study

    Institute of Scientific and Technical Information of China (English)

    LU Guo-ping; ZHENG Chun-miao

    2004-01-01

    Two biodegradation models are developed to represent natural attenuation of fuel-hydrocarbon contaminants as observed in a comprehensive natural-gradient tracer test in a heterogeneous aquifer on the Columbus Air Force Base in Mississippi, USA. The first, a first-order mass loss model, describes the irreversible losses of BTEX and its individual components, i.e., benzene (B), toluene (T), ethyl benzene (E), and xylene (X). The second, a reactive pathway model, describes sequential degradation pathways for BTEX utilizing multiple electron acceptors, including oxygen, nitrate, iron and sulfate, and via methanogenesis. The heterogeneous aquifer is represented by multiple hydraulic conductivity (K) zones delineated on the basis of numerous flowmeter K measurements. A direct propagation artificial neural network (DPN) is used as an inverse modeling tool to estimate the biodegradation rate constants associated with each of the K zones. In both the mass loss model and the reactive pathway model, the biodegradation rate constants show an increasing trend with the hydraulic conductivity. The finding of correlation between biodegradation kinetics and hydraulic conductivity distributions is of general interest and relevance to characterization and modeling of natural attenuation of hydrocarbons in other petroleum-product contaminated sites.

  14. Evaluating temporal changes in hydraulic conductivities near karst-terrain dams: Dokan Dam (Kurdistan-Iraq)

    Science.gov (United States)

    Dafny, Elad; Tawfeeq, Kochar Jamal; Ghabraie, Kazem

    2015-10-01

    Dam sites provide an outstanding opportunity to explore dynamic changes in the groundwater flow regime because of the high hydraulic gradient rapidly induced in their surroundings. This paper investigates the temporal changes of the hydraulic conductivities of the rocks and engineered structures via a thorough analysis of hydrological data collected at the Dokam Dam, Iraq, and a numerical model that simulates the Darcian component of the seepage. Analysis of the data indicates increased seepage with time and suggests that the hydraulic conductivity of the rocks increased as the conductivity of the grout curtain decreased. Conductivity changes on the order of 10-8 m/s, in a 20-yr period were quantified using the numerical analysis. It is postulated that the changes in hydraulic properties in the vicinity of Dokan Dam are due to suspension of fine materials, interbedded in small fissures in the rocks, and re-settlement of these materials along the curtain. Consequently, the importance of the grout curtain to minimize the downstream seepage, not only as a result of the conductivity contrast with the rocks, but also as a barrier to suspended clay sediments, is demonstrated. The numerical analysis also helped us to estimate the proportion of the disconnected karstic conduit flow to the overall flow.

  15. Improving prediction of hydraulic conductivity by constraining capillary bundle models to a maximum pore size

    Science.gov (United States)

    Iden, Sascha C.; Peters, Andre; Durner, Wolfgang

    2015-11-01

    The prediction of unsaturated hydraulic conductivity from the soil water retention curve by pore-bundle models is a cost-effective and widely applied technique. One problem for conductivity predictions from retention functions with continuous derivatives, i.e. continuous water capacity functions, is that the hydraulic conductivity curve exhibits a sharp drop close to water saturation if the pore-size distribution is wide. So far this artifact has been ignored or removed by introducing an explicit air-entry value into the capillary saturation function. However, this correction leads to a retention function which is not continuously differentiable. We present a new parameterization of the hydraulic properties which uses the original saturation function (e.g. of van Genuchten) and introduces a maximum pore radius only in the pore-bundle model. In contrast to models using an explicit air entry, the resulting conductivity function is smooth and increases monotonically close to saturation. The model concept can easily be applied to any combination of retention curve and pore-bundle model. We derive closed-form expressions for the unimodal and multimodal van Genuchten-Mualem models and apply the model concept to curve fitting and inverse modeling of a transient outflow experiment. Since the new model retains the smoothness and continuous differentiability of the retention model and eliminates the sharp drop in conductivity close to saturation, the resulting hydraulic functions are physically more reasonable and ideal for numerical simulations with the Richards equation or multiphase flow models.

  16. Differentiation in light energy dissipation between hemiepiphytic and non-hemiepiphytic Ficus species with contrasting xylem hydraulic conductivity.

    Science.gov (United States)

    Hao, Guang-You; Wang, Ai-Ying; Liu, Zhi-Hui; Franco, Augusto C; Goldstein, Guillermo; Cao, Kun-Fang

    2011-06-01

    Hemiepiphytic Ficus species (Hs) possess traits of more conservative water use compared with non-hemiepiphytic Ficus species (NHs) even during their terrestrial growth phase, which may result in significant differences in photosynthetic light use between these two growth forms. Stem hydraulic conductivity, leaf gas exchange and chlorophyll fluorescence were compared in adult trees of five Hs and five NHs grown in a common garden. Hs had significantly lower stem hydraulic conductivity, lower stomatal conductance and higher water use efficiency than NHs. Photorespiration played an important role in avoiding photoinhibition at high irradiance in both Hs and NHs. Under saturating irradiance levels, Hs tended to dissipate a higher proportion of excessive light energy through thermal processes than NHs, while NHs dissipated a larger proportion of electron flow than Hs through the alternative electron sinks. No significant difference in maximum net CO2 assimilation rate was found between Hs and NHs. Stem xylem hydraulic conductivity was positively correlated with maximum electron transport rate and negatively correlated with the quantum yield of non-photochemical quenching across the 10 studied Ficus species. These findings indicate that a canopy growth habit during early life stages in Hs of Ficus resulted in substantial adaptive differences from congeneric NHs not only in water relations but also in photosynthetic light use and carbon economy. The evolution of epiphytic growth habit, even for only part of their life cycle, involved profound changes in a suite of inter-correlated ecophysiological traits that persist to a large extent even during the later terrestrial growth phase.

  17. ESTIMATION OF HYDRAULIC CONDUCTIVITY AND CONTENT OF FINES FROM EXPERIMENTAL LAWS THAT CORELATE HYDRAULIC AND ELECTRIC PARAMETERS

    Directory of Open Access Journals (Sweden)

    Héctor José Peinado-Guevara

    2010-09-01

    Full Text Available Hydraulic conductivity is a basic element in the advancement of knowledge of a geological environment in both the flow and transport processes of pollutants for conservation projects, managementand environmental management and also for the development of public policies for protection of ecosystems, among others. The aim of this paper is to obtain the hydraulic conductivity (K and the finescontent (C of saturated granular half using two empirical laws. One correlates the electrical conductivity of saturated granular media σo and water saturated σw which depends on the formation factor(F, cation exchange capacity (CEC and the fines content in the saturated soil. Using data obtained from materials of 18 samples from 6 wells the relationships between F-C and CEC-C were obtained,so the equation reduces to a σo function in terms of σw and C, with a correlation coefficient of R = 0.97. A second experimental law is the one that results from the experimental relationship between K and C,being 1.4054 K 0.1804.C with a correlation coefficient of R = 0.96. From both experimental expressions relationships between K and C, a and C,and C are created so from every pair knowing one of them you get to know the other one. Under the scheme outlined electrical conductivity sections for the saturated medium and fines content are obtained,finding that the groundwater in the study area consists of a thin top layer and beneath it there is a predominantly sandy environment.

  18. Final Report - Hydraulic Conductivity with Depth for Underground Test Area (UGTA) Wells

    Energy Technology Data Exchange (ETDEWEB)

    P. Oberlander; D. McGraw; C. Russell

    2007-10-31

    Hydraulic conductivity with depth has been calculated for Underground Test Area (UGTA) wells in volcanic tuff and carbonate rock. The following wells in volcanic tuff are evaluated: ER-EC-1, ER-EC-2a, ER-EC-4, ER-EC-5, ER-5-4#2, ER-EC-6, ER-EC-7, and ER-EC-8. The following wells in carbonate rock are evaluated: ER-7-1, ER-6-1, ER-6-1#2, and ER-12-3. There are a sufficient number of wells in volcanic tuff and carbonate rock to associate the conductivity values with the specific hydrogeologic characteristics such as the stratigraphic unit, hydrostratigraphic unit, hydrogeologic unit, lithologic modifier, and alteration modifier used to describe the hydrogeologic setting. Associating hydraulic conductivity with hydrogeologic characteristics allows an evaluation of the data range and the statistical distribution of values. These results are relevant to how these units are considered in conceptual models and represented in groundwater models. The wells in volcanic tuff illustrate a wide range of data values and data distributions when associated with specific hydrogeologic characteristics. Hydraulic conductivity data within a hydrogeologic characteristic can display normal distributions, lognormal distributions, semi-uniform distribution, or no identifiable distribution. There can be multiple types of distributions within a hydrogeologic characteristic such as a single stratigraphic unit. This finding has implications for assigning summary hydrogeologic characteristics to hydrostratigraphic and hydrogeologic units. The results presented herein are specific to the hydrogeologic characteristic and to the wells used to describe hydraulic conductivity. The wells in carbonate rock are associated with a fewer number of hydrogeologic characteristics. That is, UGTA wells constructed in carbonate rock have tended to be in similar hydrogeologic materials, and show a wide range in hydraulic conductivity values and data distributions. Associations of hydraulic conductivity and

  19. Conducting polymers in electronic chemical sensors.

    Science.gov (United States)

    Janata, Jiri; Josowicz, Mira

    2003-01-01

    Conducting organic polymers have found two main kinds of application in electronics so far: as materials for construction of various devices and as selective layers in chemical sensors. In either case, interaction with ambient gases is critical. It may compromise the performance of a device based on conducting polymers, whereas it is beneficial in a sensor. Conductivity has been the primary property of interest. Work function--related to conductivity, but in principle a different property--has received only scant attention. Our aim here is to discuss the usability of conducting polymers in both types of electronic applications in light of these two parameters.

  20. Conducting polymer based biomolecular electronic devices

    Indian Academy of Sciences (India)

    B D Malhotra; Rahul Singhal

    2003-08-01

    Biomolecular electronics is rapidly evolving from physics, chemistry, biology, electronics and information technology. Organic materials such as proteins, pigments and conducting polymers have been considered as alternatives for carrying out the functions that are presently being performed by semiconductor silicon. Conducting polymers such as polypyrroles, polythiophenes and polyanilines have been projected for applications for a wide range of biomolecular electronic devices such as optical, electronic, drug-delivery, memory and biosensing devices. Our group has been actively working towards the application of conducting polymers to Schottky diodes, metal–insulator–semiconductor (MIS) devices and biosensors for the past 10 years. This paper is a review of some of the results obtained at our laboratory in the area of conducting polymer biomolecular electronics.

  1. The effect of mineral-ion interactions on soil hydraulic conductivity

    Science.gov (United States)

    The reuse of winery wastewater (WW) for irrigation could provide an alternative water source for wine production. The shift of many wineries and other food processing industries to K+-based cleaners requires studies on the effects of K+ on soil hydraulic conductivity (HC). Soils of contrasting mine...

  2. Evaluation of two methods for measuring saturated hydraulic conductivity of soils under two vegetation covers

    Energy Technology Data Exchange (ETDEWEB)

    Rubio, C.M.; Josa, R.; Poyatos, R.; Llorens, P.; Gallart, F.; Latron, J.; Ferrer, F.

    2009-07-01

    The main goal of this work is to determine and to evaluate the saturated hydraulic conductivity for a silt loam soil in field and laboratory conditions. the experimental area was located in the Vallcebre research catchment, in headwaters of the Llobregat River (NE Spain). Hydraulic conductivity was measured in the field using the Guelph permeameter and field saturated hydraulic conductivity (K{sub f}s) based on Elrick equation was calculated. The Guelph permeameter measures were made in two conditions (dry and wet) and in profiles below two vegetation covers (meadows and forest). To determine the saturated hydraulic conductivity at the laboratory (K{sub s}) the constant head permeameter was used. The average K{sub f}s values for the wet period was about 2 cm.h{sup -}1. During the dry period, both soil profiles presented higher values, about 7.5 cm.h{sup -}1. Under laboratory conditions, means observed K{sub s} values were between 12 and 25 cm.h{sup -}1. The relationship K{sub f}s/k{sub s} was of 0.1 cm.h{sup -}1 in wet conditions and about 0.4 cm.h{sup -}1 in dry conditions. The results indicated significant differences between both methods and between both seasons. differences can be explained by the anisotropy of soils as a consequence of vegetation root system that promotes preferential flows paths. (Author) 10 refs.

  3. A simplified transfer function for estimating saturated hydraulic conductivity of porous drainage filters

    DEFF Research Database (Denmark)

    Canga, Eriona; Iversen, Bo Vangsø; Kjærgaard, Charlotte

    2013-01-01

    Knowledge of the saturated hydraulic conductivity (Ksat) of porous filters used in water treatment technologies is important for optimizing the retention of nutrients and pollutants. This parameter determines the hydraulic capacity, which together with the Chemical properties of the filter media......, bulk density, uniformity coefficient, particle density, and porosity of 46 porous media fractions. The fractions ranged in grain size from 0.5 to 20 mm and were obtained from seven commercial available coarse filter materials. A backward stepwise regression analysis was performed between Ksat and 10...

  4. Electronically conducting polymers with silver grains

    Science.gov (United States)

    Murphy, Oliver J. (Inventor); Hitchens, G. Duncan (Inventor); Hodko, Dolibor (Inventor)

    1999-01-01

    The present invention provides electronically conducting polymer films formed from photosensitive formulations of pyrrole and an electron acceptor that have been selectively exposed to UV light, laser light, or electron beams. The formulations may include photoinitiators, flexibilizers, solvents and the like. These solutions can be used in applications including printed circuit boards and through-hole plating and enable direct metallization processes on non-conducting substrates. After forming the conductive polymer patterns, a printed wiring board can be formed by sensitizing the polymer with palladium and electrolytically depositing copper.

  5. A low cost apparatus for measuring the xylem hydraulic conductance in plants

    Directory of Open Access Journals (Sweden)

    Luciano Pereira

    2012-01-01

    Full Text Available Plant yield and resistance to drought are directly related to the efficiency of the xylem hydraulic conductance and the ability of this system to avoid interrupting the flow of water. In this paper we described in detail the assembling of an apparatus proposed by TYREE et al. (2002, and its calibration, as well as low cost adaptations that make the equipment accessible for everyone working in this research area. The apparatus allows measuring the conductance in parts of roots or shoots (root ramifications or branches, or in the whole system, in the case of small plants or seedlings. The apparatus can also be used to measure the reduction of conductance by embolism of the xylem vessels. Data on the hydraulic conductance of eucalyptus seedlings obtained here and other reports in the literature confirm the applicability of the apparatus in physiological studies on the relationship between productivity and water stress.

  6. Contrasting xylem vessel constraints on hydraulic conductivity between native and non-native woody understory species

    Directory of Open Access Journals (Sweden)

    Maria S Smith

    2013-11-01

    Full Text Available We examined the hydraulic properties of 82 native and non-native woody species common to forests of Eastern North America, including several congeneric groups, representing a range of anatomical wood types. We observed smaller conduit diameters with greater frequency in non-native species, corresponding to lower calculated potential vulnerability to cavitation index. Non-native species exhibited higher vessel-grouping in metaxylem compared with native species, however, solitary vessels were more prevalent in secondary xylem. Higher frequency of solitary vessels in secondary xylem was related to a lower potential vulnerability index. We found no relationship between anatomical characteristics of xylem, origin of species and hydraulic conductivity, indicating that non-native species did not exhibit advantageous hydraulic efficiency over native species. Our results confer anatomical advantages for non-native species under the potential for cavitation due to freezing, perhaps permitting extended growing seasons.

  7. The chemical identity of intervessel pit membranes in Acer challenges hydrogel control of xylem hydraulic conductivity

    Science.gov (United States)

    Klepsch, Matthias M.; Schmitt, Marco; Paul Knox, J.; Jansen, Steven

    2016-01-01

    Ion-mediated enhancement of the hydraulic conductivity of xylem tissue (i.e. the ionic effect) has been reported for various angiosperm species. One explanation of the ionic effect is that it is caused by the swelling and shrinking of intervessel pit membranes due to the presence of pectins and/or other cell-wall matrix polymers such as heteroxylans or arabinogalactan–proteins (AGPs) that may contain acidic sugars. Here, we examined the ionic effect for six Acer species and their pit membrane chemistry using immunocytochemistry, including antibodies against glycoproteins. Moreover, anatomical features related to the bordered pit morphology and vessel dimensions were investigated using light and electron microscopy. The ionic effect varied from 18 % (± 9) to 32 % (± 13). Epitopes of homogalacturonan (LM18) and xylan (LM11) were not detected in intervessel pit membranes. Negative results were also obtained for glycoproteins (extensin: LM1, JIM20; AGP glycan: LM2), although AGP (JIM13)-related epitopes were detected in parenchyma cells. The mean vessel length was significantly correlated with the magnitude of the ionic effect, unlike other pit or vessel-related characteristics. Our results suggest that intervessel pit membranes of Acer are unlikely to contain pectic or other acidic polysaccharides. Therefore, alternative explanations should be tested to clarify the ionic effect. PMID:27354661

  8. Regional groundwater characteristics and hydraulic conductivity based on geological units in Korean peninsula

    Science.gov (United States)

    Kim, Y.; Suk, H.

    2011-12-01

    In this study, about 2,000 deep observation wells, stream and/or river distribution, and river's density were analyzed to identify regional groundwater flow trend, based on the regional groundwater survey of four major river watersheds including Geum river, Han river, Youngsan-Seomjin river, and Nakdong river in Korea. Hydrogeologial data were collected to analyze regional groundwater flow characteristics according to geological units. Additionally, hydrological soil type data were collected to estimate direct runoff through SCS-CN method. Temperature and precipitation data were used to quantify infiltration rate. The temperature and precipitation data were also used to quantify evaporation by Thornthwaite method and to evaluate groundwater recharge, respectively. Understanding the regional groundwater characteristics requires the database of groundwater flow parameters, but most hydrogeological data include limited information such as groundwater level and well configuration. In this study, therefore, groundwater flow parameters such as hydraulic conductivities or transmissivities were estimated using observed groundwater level by inverse model, namely PEST (Non-linear Parameter ESTimation). Since groundwater modeling studies have some uncertainties in data collection, conceptualization, and model results, model calibration should be performed. The calibration may be manually performed by changing parameters step by step, or various parameters are simultaneously changed by automatic procedure using PEST program. In this study, both manual and automatic procedures were employed to calibrate and estimate hydraulic parameter distributions. In summary, regional groundwater survey data obtained from four major river watersheds and various data of hydrology, meteorology, geology, soil, and topography in Korea were used to estimate hydraulic conductivities using PEST program. Especially, in order to estimate hydraulic conductivity effectively, it is important to perform

  9. Hydraulic conductance and water potential gradients in squash leaves showing mycorrhiza-induced increases in stomatal conductance.

    Science.gov (United States)

    Augé, Robert M; Toler, Heather D; Sams, Carl E; Nasim, Ghazala

    2008-03-01

    Stomatal conductance (gs) and transpiration rates vary widely across plant species. Leaf hydraulic conductance (k leaf) tends to change with g (s), to maintain hydraulic homeostasis and prevent wide and potentially harmful fluctuations in transpiration-induced water potential gradients across the leaf (Delta Psi leaf). Because arbuscular mycorrhizal (AM) symbiosis often increases gs in the plant host, we tested whether the symbiosis affects leaf hydraulic homeostasis. Specifically, we tested whether k leaf changes with gs to maintain Delta Psi leaf or whether Delta Psi leaf differs when gs differs in AM and non-AM plants. Colonization of squash plants with Glomus intraradices resulted in increased gs relative to non-AM controls, by an average of 27% under amply watered, unstressed conditions. Stomatal conductance was similar in AM and non-AM plants with exposure to NaCl stress. Across all AM and NaCl treatments, k leaf did change in synchrony with gs (positive correlation of gs and k leaf), corroborating leaf tendency toward hydraulic homeostasis under varying rates of transpirational water loss. However, k leaf did not increase in AM plants to compensate for the higher gs of unstressed AM plants relative to non-AM plants. Consequently, Delta Psi leaf did tend to be higher in AM leaves. A trend toward slightly higher Delta Psi leaf has been observed recently in more highly evolved plant taxa having higher productivity. Higher Delta Psi leaf in leaves of mycorrhizal plants would therefore be consistent with the higher rates of gas exchange that often accompany mycorrhizal symbiosis and that are presumed to be necessary to supply the carbon needs of the fungal symbiont.

  10. Deciphering transmissivity and hydraulic conductivity of the aquifer by vertical electrical sounding (VES) experiments in Northwest Bangladesh

    Science.gov (United States)

    Sattar, Golam Shabbir; Keramat, Mumnunul; Shahid, Shamsuddin

    2016-03-01

    The vertical electrical soundings (VESs) are carried out in 24 selective locations of Chapai-Nawabganj area of northwest Bangladesh to determine the transmissivity and hydraulic conductivity of the aquifer. Initially, the transmissivity and hydraulic conductivity are determined from the pumping data of nearby available production wells. Afterwards, the T and K are correlated with geoelectrical resistance and the total resistivity of the aquifer. The present study deciphers the functional analogous relations of the geoelectrical resistance with the transmissivity and the total resistivity with the hydraulic conductivity of the aquifer in northwest Bangladesh. It has been shown that the given equations provide reasonable values of transmissivity and hydraulic conductivity where pumping test information is unavailable. It can be expected that the aquifer properties viz. transmissivity and hydraulic conductivity of geologically similar area can be determined with the help of the obtained equations by conducting VES experiments.

  11. Toward A 3-D Picture of Hydraulic Conductivity With Multilevel Slug Tests

    Science.gov (United States)

    McElwee, C. D.; McElwee, C. D.; Ross, H. C.

    2001-12-01

    The GEMS (Geohydrologic Experiment and Monitoring Site) field area has been established (in the Kansas River valley near Lawrence, Kansas) for a variety of reasons relating to research and teaching in hydrogeology at the University of Kansas. Over 70 wells have been installed for various purposes. The site overlies an alluvial aquifer with a total thickness of about 70 feet. The water table is typically about 20 feet below the surface, giving a total saturated thickness of about 50 feet. The upper part of the aquifer is finer material consisting of silt and clay. Typically, the lower 35 feet of the aquifer is sand and gravel. A number of wells through out the site are fully screened through the sand and gravel aquifer. Some of these fully screened wells are larger diameters; however, most wells are constructed of 2 inch PVC casing. Slug tests are widely used in hydrogeology to measure hydraulic conductivity. Over the last several years we have been conducting research to improve the slug test method. We have previously reported the detailed structure of hydraulic conductivity that can be seen in a 5 inch well (McElwee and Zemansky, EOS, v. 80, no. 46, p. F397, 1999) at this site, using multilevel slug tests. The existing 2 inch, fully screened wells are spread out over the site and offer the opportunity for developing a 3-D picture of the hydraulic conductivity distribution. However, it is difficult to develop a system that allows multilevel slug tests to be done accurately and efficiently in a 2 inch well. This is especially true in regions of very high hydraulic conductivity, where the water velocity in the casing will be relatively high. The resistance caused by frictional forces in the equipment must be minimized and a model taking account of these forces must be used. We have developed a system (equipment, software, and technique) for performing multilevel slug tests in 2 inch wells. Some equipment configurations work better than others. The data that we have

  12. Models for Unsaturated Hydraulic Conductivity Based on Truncated Lognormal Pore-size Distributions

    CERN Document Server

    Malama, Bwalya

    2013-01-01

    We develop a closed-form three-parameter model for unsaturated hydraulic conductivity associated with a three-parameter lognormal model of moisture retention, which is based on lognormal grainsize distribution. The derivation of the model is made possible by a slight modification to the theory of Mualem. We extend the three-parameter lognormal distribution to a four-parameter model that also truncates the pore size distribution at a minimum pore radius. We then develop the corresponding four-parameter model for moisture retention and the associated closed-form expression for unsaturated hydraulic conductivity. The four-parameter model is fitted to experimental data, similar to the models of Kosugi and van Genuchten. The proposed four-parameter model retains the physical basis of Kosugi's model, while improving fit to observed data especially when simultaneously fitting pressure-saturation and pressure-conductivity data.

  13. Sample dimensions effect on prediction of soil water retention curve and saturated hydraulic conductivity

    Science.gov (United States)

    Ghanbarian, Behzad; Taslimitehrani, Vahid; Dong, Guozhu; Pachepsky, Yakov A.

    2015-09-01

    Soil water retention curve (SWRC) and saturated hydraulic conductivity (SHC) are key hydraulic properties for unsaturated zone hydrology and groundwater. Not only the SWRC and SHC measurements are time-consuming, but also their results are scale dependent. Although prediction of the SWRC and SHC from available parameters, such as textural data, organic matter, and bulk density have been under investigation for decades, up to now no research has focused on the effect of sample dimensions on the soil hydraulic properties pedotransfer functions development. The main purpose here is investigating sample internal diameter and height (or length) effects on the prediction of the soil water retention curve and the saturated hydraulic conductivity. We, therefore, develop pedotransfer functions using a novel approach called contrast pattern aided regression (CPXR) and consider the sample dimensions as input variables. Two datasets including 210 and 213 soil samples with known sample dimensions were extracted from the UNSODA database to develop and evaluate pedotransfer functions for the SWRC and SHC, respectively. The 10-fold cross-validation method is applied to evaluate the accuracy and reliability of the proposed regression-based models. Our results show that including sample dimensions, such as sample internal diameter and height (or length) could substantially improve the accuracy of the SWRC and SHC pedotransfer functions developed using the CPXR method.

  14. Comparison of Measured and Modelled Hydraulic Conductivities of Fractured Sandstone Cores

    Science.gov (United States)

    Baraka-Lokmane, S.; Liedl, R.; Teutsch, G.

    - A new method for characterising the detailed fracture geometry in sandstone cores is presented. This method is based on the impregnation of samples with coloured resin, without significant disturbance of the fractures. The fractures are made clearly visible by the resin, thus allowing the fracture geometry to be examined digitally. In order to model the bulk hydraulic conductivity, the samples are sectioned serially perpendicular to the flow direction. The hydraulic conductivity of individual sections is estimated by summing the contribution of the matrix and each fracture from the digital data. Finally, the hydraulic conductivity of the bulk sample is estimated by a harmonic average in series along the flow path. Results of this geometrical method are compared with actual physical conductivity values measured from fluid experiments carried out prior to sectioning. The predicted conductivity from the fracture geometry parameters (e.g., fracture aperture, fracture width, fracture length and fracture relative roughness all measured using an optical method) is in good agreement with the independent physical measurements, thereby validating the approach.

  15. Polyacrylamide effect on hydraulic conductivity of hardsetting soils in Northeast of Brazil

    Science.gov (United States)

    Silva, Laércio; Almeida, Brivaldo; Melo, Diego; Marques, Karina; Almeida, Ceres

    2013-04-01

    Among soil hydro-physical properties, hydraulic conductivity is more sensitive to changes in soil structure. Hydraulic conductivity describes the ease with which a fluid (usually water) can move through pore spaces or fractures. It depends on the intrinsic permeability of the material and on the degree of saturation, and on the density and viscosity of the fluid. Hardsetting soils present very low hydraulic conductivity values. When dry, these soils show high penetration resistance and consistency extremely hard, but change to friable when moist. In this condition are poorly structured, slaking when moist, limit agricultural machinery use and it may reduce the growth of the root system. In Brazil, these soils occur throughout of coastal zone in flat areas called "coastal tableland". Chemical ameliorant, such as polymers based on anionic polyacrylamide (PAM), improve hydraulic conductivity of soil in hardsetting soils. The primary functions of polyacrylamide soil conditioners are to increase soil tilth, aeration, and porosity and reduce compaction and water run-off. PAM effect is attributed to its ability to expand when placed in water, storing it in soil pore space, releasing it gradually to the plants. This process occurs by reducing the water flow through the pores of the soil, due to water molecules can be absorbed by PAM, providing water gradually. Thus, this study tested the hypothesis that PAM reduces the soil hardsetting character. The area is located in coastal zone in Goiana city, Pernambuco, northeastern of Brazil. This soil is typical hardsetting soil. Intact soil cores were collected from four horizons until 70cm depth. In the laboratory, the soil cores were saturated with different PAM concentrations (0.01, 0.005, 0.00125%) and H2O (control). Saturated hydraulic conductivity (Ksat) was determined using a constant head method, according to Klute and Dirksen (1986). Four replicates were used for each horizon and Tukey test at 5% probability was used by

  16. Itinerant electron model and conductance of DNA

    Institute of Scientific and Technical Information of China (English)

    Zhen QU; Da-wei KANG; Xu-tuan GAO; Shi-jie XIE

    2008-01-01

    DNA (Deoxyribonucleic acid) has recently caught the attention of chemists and physicists.A major reason for this interest is DNA's potential use in nanoelectronie devices,both as a template for assembling nanocireuits and as an element of such circuits.However,the electronic properties of the DNA molecule remain very controversial. Charge-transfer reactions and conductivity measurements show a large variety of possible electronic behavior,ranging from Anderson and bandgap insulators to effective molecular wires and induced superconductors.In this review article,we summarize the wide-ranging experimental and theoretical results of charge transport in DNA.An itinerant electron model is suggested and the effect of the density of itinerant electrons on the conductivity of DNA is studied.Calculations show that a DNA molecule may show conductivity from insulating to metallic,which explains the controversial and profuse electric characteristics of DNA to some extent.

  17. Structure of conduction electrons on polysilanes

    Energy Technology Data Exchange (ETDEWEB)

    Ichikawa, Tsuneki [Hokkaido Univ., Sapporo (Japan); Kumagai, Jun

    1998-10-01

    The orbital structures of conduction electrons on permethylated oligosilane, Si{sub 2n}(CH{sub 3}){sub 2n+2}(n = 2 - 8), and poly(cyclohexylmethylsilane) have been determined by the electron spin-echo envelope modulation signals of the radical anions of these silanes in a deuterated rigid matrix at 77 K. The conduction electron on permethylated oligosilane is delocalized over the entire main chain, whereas that on poly(cyclohexylmethylsilane) is localized on a part of the main chain composed of about six Si atoms. Quantum-chemical calculations suggest that Anderson localization due to fluctuation of {sigma} conjugation by conformational disorder of the main chain is responsible for the localization of both the conduction electron and the hole. (author)

  18. Temporal changes in hydraulic conductivity of sand porous media biofilters during wastewater infiltration due to biomat formation

    Science.gov (United States)

    Beach, Deborah N. H.; McCray, John E.; Lowe, Kathryn S.; Siegrist, Robert L.

    2005-09-01

    Porous media biofilters (PMBs) are commonly used to treat domestic wastewater. Biomats develop at the infiltrative surface of PMBs due to continued wastewater application and create an impedance to flow. The goal of this research is to quantify the temporal evolution of normalized biomat hydraulic conductivity ( Kbm/ bbm) and effective hydraulic conductivity ( Ke). Ke is the overall hydraulic conductivity of the infiltrative zone, including biomat and unsaturated media below the biomat. Research was conducted using eight one-dimensional (1D) sand columns with gravel-free and gravel-laden infiltrative surfaces. The columns were loaded at design rates of 100-200 cm/d for 20 weeks of column operation. The Ke values for these continuously loaded columns were determined from analyses of bromide-tracer tests, falling-head permeability tests, and volumetric water content measurements during biomat development. The reduction in the Ke due to biomat formation is due to two factors: reduced hydraulic conductivity of the thin biomat, and a reduced hydraulic conductivity of the subsoil due to development of a biomat-induced unsaturated flow regime. Unsaturated hydraulic conductivities of the subsoil below the biomat ( Kss) were estimated from capillary curves and water content measurements. For observed final biomat thicknesses (less than 1 cm), the biomat hydraulic conductivity, Kbm, is three orders of magnitude smaller than the unsaturated hydraulic conductivity ( Kss). However, the relatively large thickness of the vadose zone causes the Kss to be an important contributor to the overall Ke value. For these columns, the final Ke values were approximately two orders of magnitude smaller than the original value. Because the exact thickness of the biomat ( bbm) is unknown during the flow experiments, the hydraulic conductance of the biomat zone is presented using a normalized hydraulic conductivity function ( Kbm/ bbm). A similar Kbm/ bbm is reached regardless of wastewater

  19. Estimating Hydraulic Conductivities in a Fractured Shale Formation from Pressure Pulse Testing and 3d Modeling

    Science.gov (United States)

    Courbet, C.; DICK, P.; Lefevre, M.; Wittebroodt, C.; Matray, J.; Barnichon, J.

    2013-12-01

    In the framework of its research on the deep disposal of radioactive waste in shale formations, the French Institute for Radiological Protection and Nuclear Safety (IRSN) has developed a large array of in situ programs concerning the confining properties of shales in their underground research laboratory at Tournemire (SW France). One of its aims is to evaluate the occurrence and processes controlling radionuclide migration through the host rock, from the disposal system to the biosphere. Past research programs carried out at Tournemire covered mechanical, hydro-mechanical and physico-chemical properties of the Tournemire shale as well as water chemistry and long-term behaviour of the host rock. Studies show that fluid circulations in the undisturbed matrix are very slow (hydraulic conductivity of 10-14 to 10-15 m.s-1). However, recent work related to the occurrence of small scale fractures and clay-rich fault gouges indicate that fluid circulations may have been significantly modified in the vicinity of such features. To assess the transport properties associated with such faults, IRSN designed a series of in situ and laboratory experiments to evaluate the contribution of both diffusive and advective process on water and solute flux through a clay-rich fault zone (fault core and damaged zone) and in an undisturbed shale formation. As part of these studies, Modular Mini-Packer System (MMPS) hydraulic testing was conducted in multiple boreholes to characterize hydraulic conductivities within the formation. Pressure data collected during the hydraulic tests were analyzed using the nSIGHTS (n-dimensional Statistical Inverse Graphical Hydraulic Test Simulator) code to estimate hydraulic conductivity and formation pressures of the tested intervals. Preliminary results indicate hydraulic conductivities of 5.10-12 m.s-1 in the fault core and damaged zone and 10-14 m.s-1 in the adjacent undisturbed shale. Furthermore, when compared with neutron porosity data from borehole

  20. Characterisation of river-aquifer exchange fluxes: The role of spatial patterns of riverbed hydraulic conductivities

    Science.gov (United States)

    Tang, Q.; Kurtz, W.; Brunner, P.; Vereecken, H.; Hendricks Franssen, H.-J.

    2015-12-01

    Interactions between surface water and groundwater play an essential role in hydrology, hydrogeology, ecology, and water resources management. A proper characterisation of riverbed structures might be important for estimating river-aquifer exchange fluxes. The ensemble Kalman filter (EnKF) is commonly used in subsurface flow and transport modelling for estimating states and parameters. However, EnKF only performs optimally for MultiGaussian distributed parameter fields, but the spatial distribution of streambed hydraulic conductivities often shows non-MultiGaussian patterns, which are related to flow velocity dependent sedimentation and erosion processes. In this synthetic study, we assumed a riverbed with non-MultiGaussian channel-distributed hydraulic parameters as a virtual reference. The synthetic study was carried out for a 3-D river-aquifer model with a river in hydraulic connection to a homogeneous aquifer. Next, in a series of data assimilation experiments three different groups of scenarios were studied. In the first and second group of scenarios, stochastic realisations of non-MultiGaussian distributed riverbeds were inversely conditioned to state information, using EnKF and the normal score ensemble Kalman filter (NS-EnKF). The riverbed hydraulic conductivity was oriented in the form of channels (first group of scenarios) or, with the same bimodal histogram, without channelling (second group of scenarios). In the third group of scenarios, the stochastic realisations of riverbeds have MultiGaussian distributed hydraulic parameters and are conditioned to state information with EnKF. It was found that the best results were achieved for channel-distributed non-MultiGaussian stochastic realisations and with parameter updating. However, differences between the simulations were small and non-MultiGaussian riverbed properties seem to be of less importance for subsurface flow than non-MultiGaussian aquifer properties. In addition, it was concluded that both En

  1. Investigating the relationship between unsaturated hydraulic conductivity curve and confined compression curve

    Science.gov (United States)

    Bayat, Hossein; Sedaghat, Azadeh; Safari Sinegani, Ali Akbar; Gregory, Andrew S.

    2015-03-01

    This study was conducted to estimate the soil unsaturated hydraulic conductivity through the van Genuchten model using easy to measure soil properties by regression and artificial neural networks methods. In this study, 148 soil samples were taken from five provinces of Iran. Basic soil properties (clay, silt/sand and bulk density) and other soil properties were measured. Soil water retention curve was measured to obtain the unsaturated hydraulic conductivity curve using the van Genuchten-Mualem model. Confined compression curve was measured and the modified model of van Genuchten was fitted on its data. Two-thirds and one-third of the data were used for the training and testing steps, respectively. Confined compression curve parameters and other soil properties were used as predictors to estimate unsaturated hydraulic conductivity curve. Pedotransfer functions (PTFs) were developed in two separate parts: in 5 and 6 PTFs basic soil properties were or were not used as predictors, respectively. The artificial neural networks (ANNs) performed better than the regression methods. Among the ANN-developed PTFs which have not used basic soil properties as predictors, PTFa3, with the inputs of the parameters of confined compression curve (n∗, α∗ and e0), performed better than the others. Also, among the ANN-developed PTFs that used basic soil properties as predictors along with the other input variables, PTFb5 that used the σmc (stress at the maximum curvature) and σi (stress at the inflection point) as inputs along with basic soil properties, performed better than the other PTFs. The results showed a successful prediction of the hydraulic conductivity curve using confined compression curve.

  2. Determination of hydraulic conductivities of low permeability materials in the Sierra Ladrones Formation, Albuquerque basin

    Energy Technology Data Exchange (ETDEWEB)

    Planert, C.S.

    1995-06-01

    Low permeability materials in the Sierra Ladrones Formation were sampled and analyzed to determine their hydraulic conductivities using the falling head centrifugation method (fc) as described by Nimmo et al. (1991). The method is similar to the traditional falling head method, only it uses greatly increased centrifugal forces, allowing measurements to make in a relatively short amount of time. Using these measurements, variations in saturated hydraulic conductivities between different sediment types were analyzed using Analysis of Variance (ANOVA). Sampling resulted in useable data chiefly from the clay and silt facies of the formation. The range of conductivities determined are representative of brown and red clays, and silts which make up the overbank deposits of this region. Hydraulic conductivities for these overbank fines were found to range from approximately log K = {minus}9 m/s to log K = {minus}7 m/s. The upper measurement limit of the centrifuge apparatus was determined to be approximately 1.43 {times} 10{sup {minus}7} m/s and the lower limit was approximately 7.6 {times} 10{sup {minus}12} m/s.

  3. Influence of hydroponic culture method on morphology and hydraulic conductivity of roots of honey locust.

    Science.gov (United States)

    Graves, W R

    1992-09-01

    The morphology and hydraulic conductivity of root systems of Gleditsia triacanthos L. var. inermis Willd. (honey locust) grown hydroponically in sand and solution cultures were compared. Total root system length was similar in the two cultures. However, root systems grown in solution had longer primary roots, fewer lateral roots and root hairs, and a greater distance between the tip of the primary root and the junction of the youngest secondary root and the primary root than root systems grown in sand. Hydraulic conductivities of root systems grown hydroponically for 21 or 35 days in sand or solution culture were similar. These findings show that different methods of hydroponic culture can affect root morphology without altering root resistance to water transport.

  4. EVALUATION OF THE BENTONITE CONTENT IN SPENT FOUNDRY SANDS AS A FUNCTION OF HYDRAULIC CONDUCTIVITY COEFFICIENT

    Directory of Open Access Journals (Sweden)

    Schirlene Chegatti

    2013-06-01

    Full Text Available This study evaluates the relationship of the bentonite content and hydraulic conductivity coefficient (k of waste foundry sands in tests of hydraulic conductivity in a flexible wall permeameter. The test samples had concentrations of activated sodium bentonite and natural sodium bentonite between 4% and 15%. It was also analyzed chemically the liquid leachate (aluminum, barium, chromium, cadmium, lead, phenols, iron, fluoride, and manganese, following de standard tests of Standard Methods 3111 B e D for the determination of this components in liquid samples. The experiments were supplemented with cation exchange capacity analysis. The results indicate that the values of are is related to the content of bentonite in waste foundry sand and the percolation from this waste disposal.

  5. Estimating Saturated Hydraulic Conductivity from Surface Ground-Penetrating Radar Monitoring of Infiltration

    CERN Document Server

    Léger, Emmanuel; Coquet, Yves

    2013-01-01

    In this study we used Hydrus-1D to simulate water infiltration from a ring infiltrometer. We generated water content profiles at each time step of infiltration, based on a particular value of the saturated hydraulic conductivity while knowing the other van Genuchten parameters. Water content profiles were converted to dielectric permittivity profiles using the Complex Refractive Index Method relation. We then used the GprMax suite of programs to generate radargrams and to follow the wetting front using arrival time of electromagnetic waves recorded by a Ground-Penetrating Radar (GPR). Theoretically, the depth of the inflection point of the water content profile simulated at any infiltration time step is related to the peak of the reflected amplitude recorded in the corresponding trace in the radargram. We used this relationship to invert the saturated hydraulic conductivity for constant and falling head infiltrations. We present our method on synthetic examples and on two experiments carried out on sand. We f...

  6. Estimating saturated hydraulic conductivity and air permeability from soil physical properties using state-space analysis

    DEFF Research Database (Denmark)

    Poulsen, Tjalfe; Møldrup, Per; Nielsen, Don

    2003-01-01

    field were used. Multiple regression and ARIMA models yielded similar prediction accuracy, whereas state-space models generally gave significantly higher accuracy. State-space modeling suggested K-S at a given location could be predicted using nearby values of K-S, k(a100) and air-filled porosity......Estimates of soil hydraulic conductivity (K) and air permeability (k(a)) at given soil-water potentials are often used as reference points in constitutive models for K and k(a) as functions of moisture content and are, therefore, a prerequisite for predicting migration of water, air, and dissolved...... and gaseous chemicals in the vadose zone. In this study, three modeling approaches were used to identify the dependence of saturated hydraulic conductivity (K-S) and air permeability at -100 cm H2O soil-water potential (k(a100)) on soil physical properties in undisturbed soil: (i) Multiple regression, (ii...

  7. ROOT HYDRAULIC CONDUCTIVITY AND PHOTOSYNTHETIC CAPACITY OF EUCALYPT CLONAL CUTTINGS WITH ROOT MALFORMATION INDUCTIONS

    Directory of Open Access Journals (Sweden)

    Fábio Afonso Mazzei Moura de Assis Figueiredo

    2014-06-01

    Full Text Available http://dx.doi.org/10.5902/1980509814566The gain reduction of wood biomass in trees has been assigned to root deformations even in the nursery phase. The objective of this work was the evaluation of the root system hydraulic conductivity, gas exchanges and photochemical efficiency of eucalypt clonal cuttings with and without root deformation inductions. The treatments were: 1 operational cuttings without root malformation inductions (grown according to the used methodology of Fibria Cellulose S.A.; 2 root deformation inductions. These inductions did not promote decrease in the root volume. However, the deformations brought reduction of the root system hydraulic conductivity. Lower photosynthetic rates were also observed along the day in the cuttings in the root deformed cuttings. This decreasing rate is connected to stomatal and non stomatal factors.

  8. Sand box experiments with bioclogging of porous media: Hydraulic conductivity reductions

    DEFF Research Database (Denmark)

    Seifert, Dorte; Engesgaard, Peter

    2012-01-01

    Tracer experiments during clogging and de-clogging experiments in a 2D sand box were via an image analysis used to establish a data set on the relation between changes in hydraulic conductivity (K) and relative porosity (β). Clogging appears to create a finger-like tracer transport, which could...... and closer to the substrate source during the experiments suggesting that the zone of clogging moved upstream. Three clogging models, K(β), from the literature were tested for their ability to describe the temporal changes in clogging at the scale of the sand box; the model of Clement et al. (1996......) that makes no assumption on biomass distribution, the plug formation model of Thullner et al. (2002a), and the biofilm-plug formation model of Vandevivere (1995). The plug formation and biofilm-plug formation models both match the observed changes between the hydraulic conductivity of the sand box...

  9. The effect of the shape parameters of a sample on the hydraulic conductivity

    Science.gov (United States)

    Kucza, Jarosław; Ilek, Anna

    2016-03-01

    The present study is a complement to the research investigating a laboratory method for measuring the saturated hydraulic conductivity of mountain forest soils, the results of which were presented in a paper by Ilek and Kucza (2014). The aim of the study is to analyse the influence of variation of particular cross-sections of samples and their enlarged side surface on the hydraulic conductivity measurement. The results show that a narrowing in the upper section of the sample results in an approximately twice lower disturbance of the laminar water flow than the narrowing occurring inside the sample. For that reason, the extent of the effect of the cross-section narrowing on the hydraulic conductivity measurement error is dependent on the location of the narrowing. An enlarged side surface of a sample, as described by the coefficient of side surface development, is on average 30% larger than the surface of a sample having the same volume and the same average cross-sectional area but a regular shape. The values of the coefficient of side surface development for a given sample were adopted in the range of 1.10-1.56. Among the shape parameters of the analysed irregular soil samples, the greatest impact on the measurement error is exerted by their enlarged lateral surface, which almost entirely explains the whole error of hydraulic conductivity measurement. The variability of successive cross-sectional areas of samples appears to be of marginal importance for the occurrence of this error, whose mean value was 1.15%.

  10. Bayesian Model Averaging of Artificial Intelligence Models for Hydraulic Conductivity Estimation

    Science.gov (United States)

    Nadiri, A.; Chitsazan, N.; Tsai, F. T.; Asghari Moghaddam, A.

    2012-12-01

    This research presents a Bayesian artificial intelligence model averaging (BAIMA) method that incorporates multiple artificial intelligence (AI) models to estimate hydraulic conductivity and evaluate estimation uncertainties. Uncertainty in the AI model outputs stems from error in model input as well as non-uniqueness in selecting different AI methods. Using one single AI model tends to bias the estimation and underestimate uncertainty. BAIMA employs Bayesian model averaging (BMA) technique to address the issue of using one single AI model for estimation. BAIMA estimates hydraulic conductivity by averaging the outputs of AI models according to their model weights. In this study, the model weights were determined using the Bayesian information criterion (BIC) that follows the parsimony principle. BAIMA calculates the within-model variances to account for uncertainty propagation from input data to AI model output. Between-model variances are evaluated to account for uncertainty due to model non-uniqueness. We employed Takagi-Sugeno fuzzy logic (TS-FL), artificial neural network (ANN) and neurofuzzy (NF) to estimate hydraulic conductivity for the Tasuj plain aquifer, Iran. BAIMA combined three AI models and produced better fitting than individual models. While NF was expected to be the best AI model owing to its utilization of both TS-FL and ANN models, the NF model is nearly discarded by the parsimony principle. The TS-FL model and the ANN model showed equal importance although their hydraulic conductivity estimates were quite different. This resulted in significant between-model variances that are normally ignored by using one AI model.

  11. Estimation of hydraulic conductivity of a coastal aquifer using satellite imagery

    Science.gov (United States)

    Rebolledo-Vieyra, M.; Iglesias-Prieto, R.; Marino-Tapia, I.

    2012-12-01

    The northern Yucatan Peninsula is characterized by a young and dynamic karstic system that yields very high secondary porosity and permeability. However, we have little, if none, knowledge about the hydraulic conductivity and the amount of groundwater being discharged in to ocean. Here we present and estimation of the hydraulic conductivity and quantity of groundwater being discharged by the northern Yucatan Peninsula coastal aquifer into the Gulf of Mexico, using the Sea Surface Temperature (SST) Images offshore the Yucatan coast, where we have detected a thermal anomaly that appears few hours after heavy rainfall in northern Yucatan. We associated these thermal anomalies of the SST to the groundwater being discharged into the ocean. To test our hypothesis we conducted a review of extreme rainfall events in the last 10 years; in parallel we used data from pressure and flow direction gauges installed in a known submarine groundwater discharge (SGD) to estimate the hydraulic conductivity and the quantity of groundwater being discharged. The satellite imagery and the rainfall data, allowed us to estimate the time lag between the rainfall and the SGD beginning, along with the hydraulic data from the gauges we have estimated the hydrogeological parameters of the coastal aquifer. This data is very important to contribute to the understanding the hydrogeological setting of the Yucatan coastal aquifer and its implications of the impact of human activities on the water quality. July 29th, 2005, NOAA's Sea Surface Temperature (SST) image of the Gulf of Mexico taken a week after hurricane Emily (2005). A thermal low is present offshore northern Yucatan.

  12. Silicon Enhances Water Stress Tolerance by Improving Root Hydraulic Conductance in Solanum lycopersicum L.

    Science.gov (United States)

    Shi, Yu; Zhang, Yi; Han, Weihua; Feng, Ru; Hu, Yanhong; Guo, Jia; Gong, Haijun

    2016-01-01

    Silicon (Si) can improve drought tolerance in plants, but the mechanism is still not fully understood. Previous research has been concentrating on Si's role in leaf water maintenance in Si accumulators, while little information is available on its role in water uptake and in less Si-accumulating plants. Here, we investigated the effects of Si on root water uptake and its role in decreasing oxidative damage in relation to root hydraulic conductance in tomato (Solanum lycopersicum 'Zhongza No.9') under water stress. Tomato seedlings were subjected to water stress induced by 10% (w/v) polyethylene glycol-6000 in the absence or presence of 2.5 mM added silicate. The results showed that Si addition ameliorated the inhibition in tomato growth and photosynthesis, and improved water status under water stress. The root hydraulic conductance of tomato plants was decreased under water stress, and it was significantly increased by added Si. There was no significant contribution of osmotic adjustment in Si-enhanced root water uptake under water stress. The transcriptions of plasma membrane aquaporin genes were not obviously changed by Si under water stress. Water stress increased the production of reactive oxygen species and induced oxidative damage, while added Si reversed these. In addition, Si addition increased the activities of superoxide dismutase and catalase and the levels of ascorbic acid and glutathione in the roots under stress. It is concluded that Si enhances the water stress tolerance via enhancing root hydraulic conductance and water uptake in tomato plants. Si-mediated decrease in membrane oxidative damage may have contributed to the enhanced root hydraulic conductance.

  13. Silicon enhances water stress tolerance by improving root hydraulic conductance in Solanum lycopersicum L.

    Directory of Open Access Journals (Sweden)

    Yu eShi

    2016-02-01

    Full Text Available Silicon (Si can improve drought tolerance in plants, but the mechanism is still not fully understood. Previous research has been concentrating on Si’s role in leaf water maintenance in Si accumulators, while little information is available on its role in water uptake and in less Si-accumulating plants. Here, we investigated the effects of Si on root water uptake and its role in decreasing oxidative damage in relation to root hydraulic conductance in tomato (Solanum lycopersicum ‘Zhongza No.9’ under water stress. Tomato seedlings were subjected to water stress induced by 10% (w/v polyethylene glycol-6000 in the absence or presence of 2.5 mM added silicate. The results showed that Si addition ameliorated the inhibition in tomato growth and photosynthesis, and improved water status under water stress. The root hydraulic conductance of tomato plants was decreased under water stress, and it was significantly increased by added Si. There was no significant contribution of osmotic adjustment in Si-enhanced root water uptake under water stress. The transcriptions of plasma membrane aquaporin genes were not obviously changed by Si under water stress. Water stress increased the production of reactive oxygen species and induced oxidative damage, while added Si reversed these. In addition, Si addition increased the activities of superoxide dismutase and catalase and the levels of ascorbic acid and glutathione in the roots under stress. It is concluded that Si enhances the water stress tolerance via enhancing root hydraulic conductance and water uptake in tomato plants. Si-mediated decrease in membrane oxidative damage may have contributed to the enhanced root hydraulic conductance.

  14. Influence of soil, land use and climatic factors on the hydraulic conductivity of soil

    Science.gov (United States)

    Jarvis, N.; Koestel, J.; Messing, I.; Moeys, J.; Lindahl, A.

    2013-12-01

    Due to inadequate data support, existing algorithms used to estimate soil hydraulic conductivity, K, in (eco)hydrological models ignore the effects of key site factors such as land use and climate and underplay the significant effects of soil structure on water flow at and near saturation. These limitations may introduce serious bias and error into predictions of terrestrial water balances and soil moisture status, and thus plant growth and rates of biogeochemical processes. To resolve these issues, we collated a new global database of hydraulic conductivity measured by tension infiltrometer under field conditions. The results of our analyses on this data set contrast markedly with those of existing algorithms used to estimate K. For example, saturated hydraulic conductivity, Ks, in the topsoil (< 0.3 m depth) was found to be only weakly related to texture. Instead, the data suggests that Ks depends more strongly on bulk density, organic carbon content and land use. In this respect, organic carbon was negatively correlated with Ks, presumably due to water repellency, while Ks at arable sites was, on average, ca. 2-3 times smaller than under natural vegetation, forests and perennial agriculture. The data also clearly demonstrates that clay soils have smaller K in the soil matrix and thus a larger contribution of soil macropores to K at and near saturation.

  15. Ensemble Kalman filter versus ensemble smoother for assessing hydraulic conductivity via tracer test data assimilation

    Directory of Open Access Journals (Sweden)

    E. Crestani

    2013-04-01

    Full Text Available Estimating the spatial variability of hydraulic conductivity K in natural aquifers is important for predicting the transport of dissolved compounds. Especially in the nonreactive case, the plume evolution is mainly controlled by the heterogeneity of K. At the local scale, the spatial distribution of K can be inferred by combining the Lagrangian formulation of the transport with a Kalman-filter-based technique and assimilating a sequence of time-lapse concentration C measurements, which, for example, can be evaluated on site through the application of a geophysical method. The objective of this work is to compare the ensemble Kalman filter (EnKF and the ensemble smoother (ES capabilities to retrieve the hydraulic conductivity spatial distribution in a groundwater flow and transport modeling framework. The application refers to a two-dimensional synthetic aquifer in which a tracer test is simulated. Moreover, since Kalman-filter-based methods are optimal only if each of the involved variables fit to a Gaussian probability density function (pdf and since this condition may not be met by some of the flow and transport state variables, issues related to the non-Gaussianity of the variables are analyzed and different transformation of the pdfs are considered in order to evaluate their influence on the performance of the methods. The results show that the EnKF reproduces with good accuracy the hydraulic conductivity field, outperforming the ES regardless of the pdf of the concentrations.

  16. Effect of formation characteristics on hydraulic conductivity in unconfined bed in Etchie, rivers state of Nigeria

    Directory of Open Access Journals (Sweden)

    Solomon Ndubuisi Eluozo

    2013-01-01

    Full Text Available Formation characteristics determine the hydraulic conductivity of the soil, the major parameter that determine the rate of hydraulic conductivity of the soil in study location are void ratio and permeability of the soil, degree of void ratio and permeability where determine to evaluate the rate of hydraulic conductivity and storage coefficient,the results from these two parameters  shows the variation deposition of void ratio and permeability in the study location. Ground water hydrogeological data where found to be unavailable in the study area this condition has resulted to a lots of abortive well, this has also cause a lot of abandoned ground water project done by government, this type of economic waste is a serious concern and need to be addressed., the study is imperative because it will improve the result of ground water exploration in the study area, the result from this study will definitely serve as baseline for professional to apply in   the development of ground water system in the study area .

  17. The effect of subsurface military detonations on vadose zone hydraulic conductivity, contaminant transport and aquifer recharge

    Science.gov (United States)

    Lewis, Jeffrey; Burman, Jan; Edlund, Christina; Simonsson, Louise; Berglind, Rune; Leffler, Per; Qvarfort, Ulf; Thiboutot, Sonia; Ampleman, Guy; Meuken, Denise; Duvalois, Willem; Martel, Richard; Sjöström, Jan

    2013-03-01

    Live fire military training involves the detonation of explosive warheads on training ranges. The purpose of this experiment is to evaluate the hydrogeological changes to the vadose zone caused by military training with high explosive ammunition. In particular, this study investigates artillery ammunition which penetrates underground prior to exploding, either by design or by defective fuze mechanisms. A 105 mm artillery round was detonated 2.6 m underground, and hydraulic conductivity measurements were taken before and after the explosion. A total of 114 hydraulic conductivity measurements were obtained within a radius of 3 m from the detonation point, at four different depths and at three different time periods separated by 18 months. This data was used to produce a three dimensional numerical model of the soil affected by the exploding artillery round. This model was then used to investigate potential changes to aquifer recharge and contaminant transport caused by the detonating round. The results indicate that an exploding artillery round can strongly affect the hydraulic conductivity in the vadose zone, increasing it locally by over an order of magnitude. These variations, however, appear to cause relatively small changes to both local groundwater recharge and contaminant transport.

  18. Indirect measurements of field-scale hydraulic conductivity of waste from two landfill sites.

    Science.gov (United States)

    Fleming, I R

    2011-12-01

    Management and prediction of the movement and distribution of fluids in large landfills is important for various reasons. Bioreactor landfill technology shows promise, but in arid or semi-arid regions, the natural content of landfilled waste may be low, thus requiring addition of significant volumes of water. In more humid locations, landfills can become saturated, flooding gas collection systems and causing sideslope leachate seeps or other undesirable occurrences. This paper compares results from two different approaches to monitoring water in waste. At the Brock West Landfill in eastern Canada, positive pore pressures were measured at various depths in saturated waste. The downward seepage flux through the waste is known, thus the vertical saturated hydraulic conductivity of the waste at this landfill was determined to be 3 × 10(-7)cm/s. By comparison, the Spadina Landfill in western Canada is predominantly unsaturated. The infiltration of moisture into the waste was measured using moisture sensors installed in boreholes which determined arrival time for moisture fronts resulting from major precipitation events as well as longer-term change in moisture content resulting from unsaturated drainage during winter when frozen ground prevented infiltration. The unsaturated hydraulic conductivity calculated from these data ranged from approximately 10(-6)cm/s for the slow winter drainage in the absence of significant recharge to 10(-2)cm/s or higher for shallow waste subject to high infiltration through apparent preferential pathways. These two very different approaches to field-scale measurements of vertical hydraulic conductivity provide insight into the nature of fluid movement in saturated and unsaturated waste masses. It is suggested that the principles of unsaturated seepage apply reasonably well for landfilled waste and that the hydraulic behavior of waste is profoundly influenced by the nature and size of voids and by the degree of saturation prevailing in the

  19. Borehole Heat Exchanger Systems: Hydraulic Conductivity and Frost-Resistance of Backfill Materials

    Science.gov (United States)

    Anbergen, Hauke; Sass, Ingo

    2016-04-01

    Ground source heat pump (GSHP) systems are economic solutions for both, domestic heating energy supply, as well as underground thermal energy storage (UTES). Over the past decades the technology developed to complex, advanced and highly efficient systems. For an efficient operation of the most common type of UTES, borehole heat exchanger (BHE) systems, it is necessary to design the system for a wide range of carrier fluid temperatures. During heat extraction, a cooled carrier fluid is heated up by geothermal energy. This collected thermal energy is energetically used by the heat pump. Thereby the carrier fluid temperature must have a lower temperature than the surrounding underground in order to collect heat energy. The steeper the thermal gradient, the more energy is transferred to the carrier fluid. The heat injection case works vice versa. For fast and sufficient heat extraction, even over long periods of heating (winter), it might become necessary to run the BHE with fluid temperatures below 0°C. As the heat pump runs periodically, a cyclic freezing of the pore water and corresponding ice-lens growth in the nearfield of the BHE pipes becomes possible. These so called freeze-thaw-cycles (FTC) are a critical state for the backfill material, as the sealing effect eventually decreases. From a hydrogeological point of view the vertical sealing of the BHE needs to be secured at any time (e.g. VDI 4640-2, Draft 2015). The vertical hydraulic conductivity of the BHE is influenced not only by the permeability of the grouting material itself, but by the contact area between BHE pipes and grout. In order to assess the sealing capacity of grouting materials a laboratory testing procedure was developed that measures the vertical hydraulic conductivity of the system BHE pipe and grout. The key features of the procedure are: • assessment of the systeḿs hydraulic conductivity • assessment of the systeḿs hydraulic conductivity after simulation of freeze-thaw-cycle

  20. Impact of root growth and root hydraulic conductance on water availability of young walnut trees

    Science.gov (United States)

    Jerszurki, Daniela; Couvreur, Valentin; Hopmans, Jan W.; Silva, Lucas C. R.; Shackel, Kenneth A.; de Souza, Jorge L. M.

    2015-04-01

    Walnut (Juglans regia L.) is a tree species of high economic importance in the Central Valley of California. This crop has particularly high water requirements, which makes it highly dependent on irrigation. The context of decreasing water availability in the state calls for efficient water management practices, which requires improving our understanding of the relationship between water application and walnut water availability. In addition to the soil's hydraulic conductivity, two plant properties are thought to control the supply of water from the bulk soil to the canopy: (i) root distribution and (ii) plant hydraulic conductance. Even though these properties are clearly linked to crop water requirements, their quantitative relation remains unclear. The aim of this study is to quantitatively explain walnut water requirements under water deficit from continuous measurements of its water consumption, soil and stem water potential, root growth and root system hydraulic conductance. For that purpose, a greenhouse experiment was conducted for a two month period. Young walnut trees were planted in transparent cylindrical pots, equipped with: (i) rhizotron tubes, which allowed for non-invasive monitoring of root growth, (ii) pressure transducer tensiometers for soil water potential, (iii) psychrometers attached to non-transpiring leaves for stem water potential, and (iv) weighing scales for plant transpiration. Treatments consisted of different irrigation rates: 100%, 75% and 50% of potential crop evapotranspiration. Plant responses were compared to predictions from three simple process-based soil-plant-atmosphere models of water flow: (i) a hydraulic model of stomatal regulation based on stem water potential and vapor pressure deficit, (ii) a model of plant hydraulics predicting stem water potential from soil-root interfaces water potential, and (iii) a model of soil water depletion predicting the water potential drop between the bulk soil and soil-root interfaces

  1. Integration of Tracer Test Data to Refine Geostatistical Hydraulic Conductivity Fields Using Sequential Self-Calibration Method

    Institute of Scientific and Technical Information of China (English)

    Bill X Hu; Jiang Xiaowei; Wan Li

    2007-01-01

    On the basis of local measurements of hydraulic conductivity, geostatistical methods have been found to be useful in heterogeneity characterization of a hydraulic conductivity field on a regional scale. However, the methods are not suited to directly integrate dynamic production data, such as,hydraulic head and solute concentration, into the study of conductivity distribution. These data, which record the flow and transport processes in the medium, are closely related to the spatial distribution of hydraulic conductivity. In this study, a three-dimensional gradient-based inverse method-the sequential self-calibration (SSC) method-is developed to calibrate a hydraulic conductivity field,initially generated by a geostatistical simulation method, conditioned on tracer test results. The SSC method can honor both local hydraulic conductivity measurements and tracer test data. The mismatch between the simulated hydraulic conductivity field and the reference true one, measured by its mean square error (MSE), is reduced through the SSC conditional study. In comparison with the unconditional results, the SSC conditional study creates the mean breakthrough curve much closer to the reference true curve, and significantly reduces the prediction uncertainty of the solute transport in the observed locations. Further, the reduction of uncertainty is spatially dependent, which indicates that good locations, geological structure, and boundary conditions will affect the efficiency of the SSC study results.

  2. Electrically conductive and thermally conductive materials for electronic packaging

    Science.gov (United States)

    Liu, Zongrong

    The aim of this dissertation is to develop electrically or thermally conductive materials that are needed for electronic packaging and microelectronic cooling. These materials are in the form of coatings and are made from pastes. The research work encompasses paste formulation, studying the process of converting a paste to a conductive material, relating the processing conditions to the structure and performance, and evaluating performance attributes that are relevant to the application of these conductive materials. The research has resulted in new information that is valuable to the microelectronic industry. Work on electrically conductive materials emphasizes the development of electrical interconnection materials in the form of air-firable glass-free silver-based electrically conductive thick films, which use the Ti-Al alloy as the binder and are in contrast to conventional films that use glass as the binder. The air-firability, as enabled by minor additions of tin and zinc to the paste, is in contrast to previous glass-free films that are not firable. The recommended firing condition is 930°C in air. The organic vehicle in the paste comprises ethyl cellulose, which undergoes thermal decomposition during burnout of the paste. The ethyl cellulose is dissolved in ether, which facilitates the burnout. Excessive ethyl cellulose hinders the burnout. A higher heating rate results in more residue after burnout. The presence of silver particles facilitates drying and burnout. Firing in air gives lower resistivity than firing in oxygen. Firing in argon gives poor films. Compared to conventional films that use glass as the binder, these films, when appropriately fired, exhibit lower electrical resistivity (2.5 x 10-6 O.cm) and higher scratch resistance. Work on thermally conductive materials addresses thermal interface materials, which are materials placed at the interface between a heat sink and a heat source for the purpose of improving the thermal contact. Heat

  3. The hydraulic conductivity of the xylem in conifer needles (Picea abies and Pinus mugo).

    Science.gov (United States)

    Charra-Vaskou, Katline; Mayr, Stefan

    2011-08-01

    Main resistances of the plant water transport system are situated in leaves. In contrast to angiosperm leaves, knowledge of conifer needle hydraulics and of the partitioning of resistances within needles is poor. A new technique was developed which enabled flow-meter measurements through needles embedded in paraffin and thus quantification of the specific hydraulic conductivity (K(s)) of the needle xylem. In Picea abies, xylem K(s) of needle and axes as well as in needles of different age were compared. In Pinus mugo, resistance partitioning within needles was estimated by measurements of xylem K(s) and leaf conductance (K(leaf), measured via 'rehydration kinetics'). Mean K(s) in P. abies needles was 3.5×10(-4) m(2) s(-1) MPa(-1) with a decrease in older needles, and over all similar to K(s) of corresponding axes xylem. In needles of P. mugo, K(s) was 0.9×10(-4) m(2) s(-1) MPa(-1), and 24% of total needle resistance was situated in the xylem. The results indicate species-specific differences in the hydraulic efficiency of conifer needle xylem. The vascular section of the water transport system is a minor but relevant resistance in needles.

  4. A complete soil hydraulic model accounting for capillary and adsorptive water retention, capillary and film conductivity, and hysteresis

    NARCIS (Netherlands)

    Sakai, Masaru; Van Genuchten, Martinus Th; Alazba, A. A.; Setiawan, Budi Indra; Minasny, Budiman

    2015-01-01

    A soil hydraulic model that considers capillary hysteretic and adsorptive water retention as well as capillary and film conductivity covering the complete soil moisture range is presented. The model was obtained by incorporating the capillary hysteresis model of Parker and Lenhard into the hydraulic

  5. Electronic structure calculations on helical conducting polymers.

    Science.gov (United States)

    Ripoll, Juan D; Serna, Andrei; Guerra, Doris; Restrepo, Albeiro

    2010-10-21

    We present a study of the electronic structure and derived properties of polyfurane (PFu), polypyrrol (PPy), and polythiophene (PTh). Two spatial arrangements are considered: trans chain (tc-PFu, tc-PPy, tc-PTh) and cis α-helical (α-PFu, α-PPy, α-PTh). Even at the small sizes considered here, helical conformations appear to be stable. Band gaps of pure, undoped oligomers fall into the semiconductor range. Density of states (DOS) analysis suggest dense valence and conduction bands. Bond length alternation analysis predicts almost complete delocalization of the π clouds in all spatial arrangements. Doping with electron donors or electron-withdrawing impurities reduces all band gaps close to the metallic regime in addition to increasing the DOS for the valence and conduction bands.

  6. Soil hydraulic properties and REV study using X-ray microtomography and pore-scale modelling: saturated hydraulic conductivity

    Science.gov (United States)

    Gerke, Kirill; Khirevich, Siarhei; Sizonenko, Timofey; Karsanina, Marina; Umarova, Aminat; Korost, Dmitry; Matthai, Stephan; Mallants, Dirk

    2016-04-01

    To verify pore-scale modelling approach for determination of soil saturated hydraulic conductivity properties we scanned three cylindrical soil samples taken from A, Ah and B horizons using X-ray microtomography method. Resulting 3D soil images with resolutions of 15.25-20.96 μm were segmented into pores and solids and their maximum inscribed cube subvolumes were used as input data for three major pore-scale modelling methods to simulate saturated flow - lattice-Boltzmann method, finite-difference solution of the Stokes problem, and pore-network model. Provided that imaging resolution is high enough to capture the backbone of effective porosity and the main conducting pores all three methods resulted in simulated soil permeabilities close to experimental values for Ah and B samples. The resolution of A sample was not enough for an accurate modelling and we concluded that this soil requires multi-scale imaging to cover all relevant heterogeneities. We demonstrate that popular SWV method to choose segmentation threshold resulted in oversegmentation and order of magnitude higher permeability values. Careful manual thresholding combined with local segmentation algorithm provided much more accurate results. Detailed analysis of water retention curves showed that air-filled porosity at relevant pressure stages cannot be used for verification of the segmentation results. Representativity analysis by simulating flow in increasing soil volume up to 2.8 cm3 revealed no representative elementary volume (REV) within Ah sample and non-uniqueness of REV for B sample. The latter was explained by soil structure non-stationarity. We further speculate that structures soil horizons can exhibit no REV at all. We discuss numerous advantages of coupled imaging and pore-scale modelling approach and show how it can become a successor of the conventional soil coring method to parametrize large scale continuum models.

  7. Using environmental tracers and transient hydraulic heads to estimate groundwater recharge and conductivity

    Science.gov (United States)

    Erdal, Daniel; Cirpka, Olaf A.

    2017-04-01

    Regional groundwater flow strongly depends on groundwater recharge and hydraulic conductivity. While conductivity is a spatially variable field, recharge can vary in both space and time. None of the two fields can be reliably observed on larger scales, and their estimation from other sparse data sets is an open topic. Further, common hydraulic-head observations may not suffice to constrain both fields simultaneously. In the current work we use the Ensemble Kalman filter to estimate spatially variable conductivity, spatiotemporally variable recharge and porosity for a synthetic phreatic aquifer. We use transient hydraulic-head and one spatially distributed set of environmental tracer observations to constrain the estimation. As environmental tracers generally reside for a long time in an aquifer, they require long simulation times and carries a long memory that makes them highly unsuitable for use in a sequential framework. Therefore, in this work we use the environmental tracer information to precondition the initial ensemble of recharge and conductivities, before starting the sequential filter. Thereby, we aim at improving the performance of the sequential filter by limiting the range of the recharge to values similar to the long-term annual recharge means and by creating an initial ensemble of conductivities that show similar pattern and values to the true field. The sequential filter is then used to further improve the parameters and to estimate the short term temporal behavior as well as the temporally evolving head field needed for short term predictions within the aquifer. For a virtual reality covering a subsection of the river Neckar it is shown that the use of environmental tracers can improve the performance of the filter. Results using the EnKF with and without this preconditioned initial ensemble are evaluated and discussed.

  8. The influence of topology on hydraulic conductivity in a sand-and-gravel aquifer

    Science.gov (United States)

    Morin, R.H.; LeBlanc, D.R.; Troutman, B.M.

    2010-01-01

    A field experiment consisting of geophysical logging and tracer testing was conducted in a single well that penetrated a sand-and-gravel aquifer at the U.S. Geological Survey Toxic Substances Hydrology research site on Cape Cod, Massachusetts. Geophysical logs and flowmeter/pumping measurements were obtained to estimate vertical profiles of porosity ??, hydraulic conductivity K, temperature, and bulk electrical conductivity under background, freshwater conditions. Saline-tracer fluid was then injected into the well for 2 h and its radial migration into the surrounding deposits was monitored by recording an electromagnetic-induction log every 10 min. The field data are analyzed and interpreted primarily through the use of Archie's (1942) law to investigate the role of topological factors such as pore geometry and connectivity, and grain size and packing configuration in regulating fluid flow through these coarse-grained materials. The logs reveal no significant correlation between K and ??, and imply that groundwater models that link these two properties may not be useful at this site. Rather, it is the distribution and connectivity of the fluid phase as defined by formation factor F, cementation index m, and tortuosity ?? that primarily control the hydraulic conductivity. Results show that F correlates well with K, thereby indicating that induction logs provide qualitative information on the distribution of hydraulic conductivity. A comparison of ??, which incorporates porosity data, with K produces only a slightly better correlation and further emphasizes the weak influence of the bulk value of ?? on K. Copyright ?? 2009 The Author(s) are Federal Government Employees. Journal compilation ?? 2009 National Ground Water Association.

  9. Improved estimation of hydraulic conductivity by combining stochastically simulated hydrofacies with geophysical data.

    Science.gov (United States)

    Zhu, Lin; Gong, Huili; Chen, Yun; Li, Xiaojuan; Chang, Xiang; Cui, Yijiao

    2016-03-01

    Hydraulic conductivity is a major parameter affecting the output accuracy of groundwater flow and transport models. The most commonly used semi-empirical formula for estimating conductivity is Kozeny-Carman equation. However, this method alone does not work well with heterogeneous strata. Two important parameters, grain size and porosity, often show spatial variations at different scales. This study proposes a method for estimating conductivity distributions by combining a stochastic hydrofacies model with geophysical methods. The Markov chain model with transition probability matrix was adopted to re-construct structures of hydrofacies for deriving spatial deposit information. The geophysical and hydro-chemical data were used to estimate the porosity distribution through the Archie's law. Results show that the stochastic simulated hydrofacies model reflects the sedimentary features with an average model accuracy of 78% in comparison with borehole log data in the Chaobai alluvial fan. The estimated conductivity is reasonable and of the same order of magnitude of the outcomes of the pumping tests. The conductivity distribution is consistent with the sedimentary distributions. This study provides more reliable spatial distributions of the hydraulic parameters for further numerical modeling.

  10. A mutation that eliminates bundle sheath extensions reduces leaf hydraulic conductance, stomatal conductance and assimilation rates in tomato (Solanum lycopersicum).

    Science.gov (United States)

    Zsögön, Agustin; Negrini, Ana Clarissa Alves; Peres, Lázaro Eustáquio Pereira; Nguyen, Hoa Thi; Ball, Marilyn C

    2015-01-01

    Bundle sheath extensions (BSEs) are key features of leaf structure whose distribution differs among species and ecosystems. The genetic control of BSE development is unknown, so BSE physiological function has not yet been studied through mutant analysis. We screened a population of ethyl methanesulfonate (EMS)-induced mutants in the genetic background of the tomato (Solanum lycopersicum) model Micro-Tom and found a mutant lacking BSEs. The leaf phenotype of the mutant strongly resembled the tomato mutant obscuravenosa (obv). We confirmed that obv lacks BSEs and that it is not allelic to our induced mutant, which we named obv-2. Leaves lacking BSEs had lower leaf hydraulic conductance and operated with lower stomatal conductance and correspondingly lower assimilation rates than wild-type leaves. This lower level of function occurred despite similarities in vein density, midvein vessel diameter and number, stomatal density, and leaf area between wild-type and mutant leaves, the implication being that the lack of BSEs hindered water dispersal within mutant leaves. Our results comparing near-isogenic lines within a single species confirm the hypothesised role of BSEs in leaf hydraulic function. They further pave the way for a genetic model-based analysis of a common leaf structure with deep ecological consequences.

  11. Property-Transfer Modeling to Estimate Unsaturated Hydraulic Conductivity of Deep Sediments at the Idaho National Laboratory, Idaho

    Science.gov (United States)

    Perkins, Kim S.; Winfield, Kari A.

    2007-01-01

    The unsaturated zone at the Idaho National Laboratory is complex, comprising thick basalt flow sequences interbedded with thinner sedimentary layers. Understanding the highly nonlinear relation between water content and hydraulic conductivity within the sedimentary interbeds is one element in predicting water flow and solute transport processes in this geologically complex environment. Measurement of unsaturated hydraulic conductivity of sediments is costly and time consuming, therefore use of models that estimate this property from more easily measured bulk-physical properties is desirable. A capillary bundle model was used to estimate unsaturated hydraulic conductivity for 40 samples from sedimentary interbeds using water-retention parameters and saturated hydraulic conductivity derived from (1) laboratory measurements on core samples, and (2) site-specific property transfer regression models developed for the sedimentary interbeds. Four regression models were previously developed using bulk-physical property measurements (bulk density, the median particle diameter, and the uniformity coefficient) as the explanatory variables. The response variables, estimated from linear combinations of the bulk physical properties, included saturated hydraulic conductivity and three parameters that define the water-retention curve. The degree to which the unsaturated hydraulic conductivity curves estimated from property-transfer-modeled water-retention parameters and saturated hydraulic conductivity approximated the laboratory-measured data was evaluated using a goodness-of-fit indicator, the root-mean-square error. Because numerical models of variably saturated flow and transport require parameterized hydraulic properties as input, simulations were run to evaluate the effect of the various parameters on model results. Results show that the property transfer models based on easily measured bulk properties perform nearly as well as using curve fits to laboratory-measured water

  12. Seasonal variability of near-saturated hydraulic conductivity on cultivated soil

    Science.gov (United States)

    Klípa, Vladimír; Zumr, David; Sněhota, Michal

    2014-05-01

    The soil structure and hydraulic properties of arable soils considerably vary during the year due to the periodical tillage and fertilization activities, soil compaction, plant and root grow, climate impact etc. The knowledge of the effect of temporal soil variability is essential when assessing water regime and associated dissolved substance transport in soils. The main aim of this contribution is to describe the temporal development of unsaturated hydraulic conductivity on arable land during a year. The experimental site is located in Nucice catchment (Central Bohemia, Czech republic), where also rainfall-runoff and soil erosion processes are studied. The soil is classified as Cambisol, typical texture ranges from loam to clay loam classes. Soil is conservatively tilled till depth of approximately 17 cm, below the topsoil a compacted subsoil was observed. Tension infiltration experiments were performed repeatedly at single location in order to determine the unsaturated hydraulic conductivity of the topsoil. So far four tension infiltration campaigns were carried out under tension h0 = -3.0 cm with different field conditions: (i) young winter barley (October 2012), (ii) between postharvest stubble breaking and seeding (April 2013), (iii) full-grown oat (June 2013) and (iv) after fresh postharvest stubble breaking (October 2013). Measurements were carried out using newly introduced automated multi minidisk tension infiltrometer (Klipa et al., EGU2014-7230). All experiments were performed on the levelled soil surface after removing upper soil layer (1 to 3 cm). A thin layer of quartz sand (thickness 1 - 2 mm, grain size 0.1 - 0.6 mm) was applied to improve contact between the infiltrometer and the soil surface. Each infiltration campaign consisted of six tension infiltration experiments, the total number of 24 infiltration data sets was obtained for this study. Results show that unsaturated hydraulic conductivity was significantly smaller in April, but rather the

  13. Interrelations among the soil-water retention, hydraulic conductivity, and suction-stress characteristic curves

    Science.gov (United States)

    Lu, Ning; Kaya, Murat; Godt, Jonathan W.

    2014-01-01

    The three fundamental constitutive relations that describe fluid flow, strength, and deformation behavior of variably saturated soils are the soil-water retention curve (SWRC), hydraulic conductivity function (HCF), and suction-stress characteristic curve (SSCC). Until recently, the interrelations among the SWRC, HCF, and SSCC have not been well established. This work sought experimental confirmation of interrelations among these three constitutive functions. Results taken from the literature for six soils and those obtained for 11 different soils were used. Using newly established analytical relations among the SWRC, HCF, and SSCC and these test results, the authors showed that these three constitutive relations can be defined by a common set of hydromechanical parameters. The coefficient of determination for air-entry pressures determined independently using hydraulic and mechanical methods is >0.99, >0.98 for the pore size parameter, and 0.94 for the residual degree of saturation. One practical implication is that one of any of the four experiments (axis-translation, hydraulic, shear-strength, or deformation) is sufficient to quantify all three constitutive relations.

  14. Water infiltration and hydraulic conductivity in a natural Mediterranean oak forest: impacts of hydrology-oriented silviculture on soil hydraulic properties

    Science.gov (United States)

    Di Prima, Simone; Bagarello, Vincenzo; Bautista, Inmaculada; Cerdà, Artemi; Cullotta, Sebastiano; del Campo, Antonio; González-Sanchis, María; Iovino, Massimo; Maetzke, Federico

    2016-04-01

    Prima, S., Iovino, M., 2015. Determining hydraulic properties of a loam soil by alternative infiltrometer techniques. Hydrol. Process. doi:10.1002/hyp.10607 Andréassian, V., 2004. Waters and forests: from historical controversy to scientific debate. Journal of Hydrology 291, 1-27. doi:10.1016/j.jhydrol.2003.12.015 Assouline, S., Mualem, Y., 2002. Infiltration during soil sealing: The effect of areal heterogeneity of soil hydraulic properties. Water Resour. Res. 38, 1286. doi:10.1029/2001WR001168 Aussenac, G., Granier, A., 1988. Effects of thinning on water stress and growth in Douglas-fir. Canadian Journal of Forest Research 18, 100-105. doi:10.1139/x88-015 Bagarello, V., Di Prima, S., Iovino, M., Provenzano, G., 2014. Estimating field-saturated soil hydraulic conductivity by a simplified Beerkan infiltration experiment. Hydrological Processes 28, 1095-1103. doi:10.1002/hyp.9649 Bens, O., Wahl, N.A., Fischer, H., Hüttl, R.F., 2006. Water infiltration and hydraulic conductivity in sandy cambisols: impacts of forest transformation on soil hydrological properties. Eur J Forest Res 126, 101-109. doi:10.1007/s10342-006-0133-7 Brooks, K.N., Folliott, P.F., Gregersen, H.M., DeBano, L.F., 2003. Hydrology and the Management of Watersheds. Hydrology and the Management of Watersheds 575. Cosandey, C., Andréassian, V., Martin, C., Didon-Lescot, J.F., Lavabre, J., Folton, N., Mathys, N., Richard, D., 2005. The hydrological impact of the mediterranean forest: a review of French research. Journal of Hydrology 301, 235-249. doi:10.1016/j.jhydrol.2004.06.040 del Campo, A.D., Fernandes, T.J.G., Molina, A.J., 2014. Hydrology-oriented (adaptive) silviculture in a semiarid pine plantation: How much can be modified the water cycle through forest management? European Journal of Forest Research 133, 879-894. doi:10.1007/s10342-014-0805-7 Di Prima, S., 2015. Automated single ring infiltrometer with a low-cost microcontroller circuit. Computers and Electronics in Agriculture 118, 390-395. doi

  15. Is inversion based high resolution characterization of spatially heterogeneous river bed hydraulic conductivity needed and possible?

    Directory of Open Access Journals (Sweden)

    W. Kurtz

    2013-05-01

    Full Text Available River-aquifer exchange fluxes influence local and regional water balances and affect groundwater and river water quality and quantity. Unfortunately, river-aquifer exchange fluxes tend to be strongly spatially variable and it is an open research question to which degree river bed heterogeneity has to be represented in a~model in order to achieve reliable estimates of river-aquifer exchange fluxes. This research question is addressed in this paper with help of synthetic simulation experiments, which mimic the Limmat aquifer in Zurich (Switzerland, where river-aquifer exchange fluxes and groundwater management activities play an important role. The solution of the unsaturated-saturated subsurface hydrological flow problem including river-aquifer interaction is calculated for ten different synthetic realities where the strongly heterogeneous river bed hydraulic conductivities (L are perfectly known. Hydraulic head data (100 in the default scenario are sampled from the synthetic realities. In subsequent data assimilation experiments, where L is unknown now, the hydraulic head data are used as conditioning information, with help of the Ensemble Kalman Filter (EnKF. For each of the ten synthetic realities, four different ensembles of L are tested in the experiments with EnKF; one ensemble estimates high resolution L-fields with different L values for each element, and the other three ensembles estimate effective L values for 5, 3 or 2 zones. The calibration of higher resolution L-fields (i.e., fully heterogeneous or 5 zones gives better results than the calibration of L for only 3 or 2 zones in terms of reproduction of states, stream-aquifer exchange fluxes and parameters. Effective L for a limited number of zones cannot always reproduce the true states and fluxes well and results in biased estimates of net exchange fluxes between aquifer and stream. Also in case only 10 head data are used for conditioning, the high resolution L-fields outperform the

  16. Unsaturated hydraulic conductivity of sandy soil columns packed to different bulk densities and water uptake by plantroots

    NARCIS (Netherlands)

    Rossi-Pisa, P.

    1978-01-01

    This paper describes a laboratory metbod used to determine both the soil moisture retention curve and the unsaturated hydraulic conductivity in soil columns under transient flow conditions during evaporation.

  17. Estimating hydraulic conductivity of fractured rocks from high‐pressure packer tests with an Izbash's law‐based empirical model

    National Research Council Canada - National Science Library

    Chen, Yi‐Feng; Hu, Shao‐Hua; Hu, Ran; Zhou, Chuang‐Bing

    2015-01-01

    ...‐pressure groundwater flow conditions. The interpretation of the HPPT data, however, remains difficult due to the transition of flow conditions in the conducting structures and the hydraulic fracturing...

  18. 2D aquifer characterization and improved prediction of hydraulic conductivity using surface Nuclear Magnetic Resonance

    Science.gov (United States)

    Dlugosch, Raphael; Günther, Thomas; Müller-Petke, Mike; Yaramanci, Ugur

    2014-05-01

    We present recent studies on the characterization of shallow aquifers using Nuclear Magnetic Resonance (NMR). NMR can help to gather detailed information about the water content and pore size related NMR relaxation time, of porous and water saturated material. The field application of surface NMR uses large wire loops placed at the surface of the Earth allows imaging the subsurface down to around hundred meters. First, a sophisticated inversion scheme is presented to simultaneously determine the two-dimensional (2D) distribution of the water content and the NMR relaxation time (T2*) in the subsurface from a surface NMR survey. The outstanding features of the new inversion scheme are its robustness to noisy data and the potential to distinguish aquifers of different lithology due to their specific NMR relaxation time. The successful application of the inversion scheme is demonstrated on two field cases both characterized by channel structures in the glacial sediments of Northern Germany. Second, we revise the prediction of hydraulic conductivity from NMR measurements for coarse-grained and unconsolidated sediments, commonly found in shallow aquifers. The presented Kozeny-Godefroy model replaces the empirical factors in known relations with physical, structural, and intrinsic NMR parameters. It additionally accounts for bulk water relaxation and is not limited to fast diffusion conditions. This improves the prediction of the hydraulic conductivity for clay-free sediments with grain sizes larger than medium sand. The model is validated by laboratory measurements on glass beads and sand samples. Combining the new inversion scheme and petrophysical model allows 2D imaging of the hydraulic conductivity in the subsurface from a surface NMR survey.

  19. Ensemble Kalman filter versus ensemble smoother for assessing hydraulic conductivity via tracer test data assimilation

    Directory of Open Access Journals (Sweden)

    E. Crestani

    2012-11-01

    Full Text Available The significance of estimating the spatial variability of the hydraulic conductivity K in natural aquifers is relevant to the possibility of defining the space and time evolution of a non-reactive plume, since the transport of a solute is mainly controlled by the heterogeneity of K. At the local scale, the spatial distribution of K can be inferred by combining the Lagrangian formulation of the transport with a Kalman filter-based technique and assimilating a sequence of time-lapse concentration C measurements, which, for example, can be evaluated on-site through the application of a geophysical method. The objective of this work is to compare the ensemble Kalman filter (EnKF and the ensemble smoother (ES capabilities to retrieve the hydraulic conductivity spatial distribution in a groundwater flow and transport modeling framework. The application refers to a two-dimensional synthetic aquifer in which a tracer test is simulated. Moreover, since Kalman filter-based methods are optimal only if each of the involved variables fit to a Gaussian probability density function (pdf and since this condition may not be met by some of the flow and transport state variables, issues related to the non-Gaussianity of the variables are analyzed and different transformation of the pdfs are considered in order to evaluate their influence on the performance of the methods. The results show that the EnKF reproduces with good accuracy the hydraulic conductivity field, outperforming the ES regardless of the pdf of the concentrations.

  20. Electron heat conduction and suprathermal particles

    Energy Technology Data Exchange (ETDEWEB)

    Bakunin, O.G.; Krasheninnikov, S.I. (I.V. Kurchatov Institute, Moscow (Russian Federation))

    1991-01-01

    As recognized at present, the applicability of Spitzer-Harm's theory on electron heat conduction along the magnetic field is limited by comparatively small values of the thermal electron mean free path ratio, [lambda] to the characteristic length of changes in plasma parameters, L: [gamma]=[lambda]/L[<=]10[sup -2]. The stationary kinetic equation for the electron distribution function inhomogeneous along the x-axis f[sub e](v,x) allows one to have solutions in the self-similar variables. The objective of a given study is to generalize the solutions for the case of arbitrary Z[sub eff], that will allow one to compare approximate solutions to the kinetic equation with the precise ones in a wide range of parameters. (author) 8 refs., 2 figs.

  1. Role of leaf hydraulic conductance in the regulation of stomatal conductance in almond and olive in response to water stress.

    Science.gov (United States)

    Hernandez-Santana, Virginia; Rodriguez-Dominguez, Celia M; Fernández, J Enrique; Diaz-Espejo, Antonio

    2016-06-01

    The decrease of stomatal conductance (gs) is one of the prime responses to water shortage and the main determinant of yield limitation in fruit trees. Understanding the mechanisms related to stomatal closure in response to imposed water stress is crucial for correct irrigation management. The loss of leaf hydraulic functioning is considered as one of the major factors triggering stomatal closure. Thus, we conducted an experiment to quantify the dehydration response of leaf hydraulic conductance (Kleaf) and its impact on gs in two Mediterranean fruit tree species, one deciduous (almond) and one evergreen (olive). Our hypothesis was that a higher Kleaf would be associated with a higher gs and that the reduction in Kleaf would predict the reduction in gs in both species. We measured Kleaf in olive and almond during a cycle of irrigation withholding. We also compared the results of two methods to measure Kleaf: dynamic rehydration kinetics and evaporative flux methods. In addition, determined gs, leaf water potential (Ψleaf), vein density, photosynthetic capacity and turgor loss point. Results showed that gs was higher in almond than in olive and so was Kleaf (Kmax = 4.70 and 3.42 mmol s(-1) MPa(-1) m(-2), in almond and olive, respectively) for Ψleaf > -1.2 MPa. At greater water stress levels than -1.2 MPa, however, Kleaf decreased exponentially, being similar for both species, while gs was still higher in almond than in olive. We conclude that although the Kleaf decrease with increasing water stress does not drive unequivocally the gs response to water stress, Kleaf is the variable most strongly related to the gs response to water stress, especially in olive. Other variables such as the increase in abscisic acid (ABA) may be playing an important role in gs regulation, although in our study the gs-ABA relationship did not show a clear pattern.

  2. Silicon enhances water stress tolerance by improving root hydraulic conductance in Solanum lycopersicum L.

    OpenAIRE

    Yu eShi; Yi eZhang; Weihua eHan; Ru eFeng; Yanhong eHu; Jia eGuo; Haijun eGong

    2016-01-01

    Silicon (Si) can improve drought tolerance in plants, but the mechanism is still not fully understood. Previous research has been concentrating on Si’s role in leaf water maintenance in Si accumulators, while little information is available on its role in water uptake and in less Si-accumulating plants. Here, we investigated the effects of Si on root water uptake and its role in decreasing oxidative damage in relation to root hydraulic conductance in tomato (Solanum lycopersicum ‘Zhongza No.9...

  3. Silicon Enhances Water Stress Tolerance by Improving Root Hydraulic Conductance in Solanum lycopersicum L.

    OpenAIRE

    SHI, YU; Zhang, Yi; Han, Weihua; Feng, Ru; Hu, Yanhong; Guo, Jia; Gong, Haijun

    2016-01-01

    Silicon (Si) can improve drought tolerance in plants, but the mechanism is still not fully understood. Previous research has been concentrating on Si’s role in leaf water maintenance in Si accumulators, while little information is available on its role in water uptake and in less Si-accumulating plants. Here, we investigated the effects of Si on root water uptake and its role in decreasing oxidative damage in relation to root hydraulic conductance in tomato (Solanum lycopersicum ‘Zhongza No.9...

  4. Hydraulic conductance and viscous coupling of three-phase layers in angular capillaries

    Science.gov (United States)

    Dehghanpour, H.; Aminzadeh, B.; Dicarlo, D. A.

    2011-06-01

    Predicting three-phase relative permeability by network models requires reliable models for hydraulic conductance of films and layers stabilized by capillary forces at the pore level. We solve the creeping flow approximation of the Navier-Stokes equation for stable wetting and intermediate layers in the corner of angular capillaries by using a continuity boundary condition at the layer interface. We find significant coupling between the condensed phases and calculate the generalized mobilities by solving cocurrent and countercurrent flow of wetting and intermediate layers. Finally, we present a simple heuristic model for the generalized mobilities as a function of the geometry and viscosity ratio.

  5. Method development for determining the hydraulic conductivity of fractured porous media

    Energy Technology Data Exchange (ETDEWEB)

    Dixon, Kenneth L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2013-09-30

    Plausible, but unvalidated, theoretical model constructs for unsaturated hydraulic conductivity of fractured porous media are currently used in Performance Assessment (PA) modeling for cracked saltstone and concrete (Flach 2011). The Nuclear Regulatory Commission (NRC) has expressed concern about the lack of model support for these assumed Moisture Characteristic Curves (MCC) data, as noted in Requests for Additional Information (RAIs) PA-8 and SP-4 (Savannah River Remediation, LLC, 2011). The objective of this task was to advance PA model support by developing an experimental method for determining the hydraulic conductivity of fractured cementitious materials under unsaturated conditions, and to demonstrate the technique on fractured saltstone samples. The task was requested through Task Technical Request (TTR) HLW-SSF-TTR-2012-0016 and conducted in accordance with Task Technical & Quality Assurance Plan (TTQAP) SRNL-TR-2012-00090. Preliminary method development previously conducted by Kohn et al. (2012) identified transient outflow extraction as the most promising method for characterizing the unsaturated properties of fractured porous media. While the research conducted by Kohn et al. (2012) focused on fractured media analogs such as stacked glass slides, the current task focused directly on fractured saltstone. For this task, four sample types with differing fracture geometries were considered: 1) intact saltstone, 2) intact saltstone with a single saw cut, smooth surface fracture, 3) micro-fractured saltstone (induced by oven drying), and 4) micro-fractured saltstone with a single, fully-penetrating, rough-surface fracture. Each sample type was tested initially for saturated hydraulic conductivity following method ASTM D 5084 using a flexible wall permeameter. Samples were subsequently tested using the transient outflow extraction method to determine cumulative outflow as a function of time and applied pressure. Of the four sample types tested, two yielded

  6. Two and Three-Phases Fractal Models Application in Soil Saturated Hydraulic Conductivity Estimation

    Directory of Open Access Journals (Sweden)

    ELNAZ Rezaei abajelu

    2017-03-01

    Full Text Available Introduction: Soil Hydraulic conductivity is considered as one of the most important hydraulic properties in water and solutionmovement in porous media. In recent years, variousmodels as pedo-transfer functions, fractal models and scaling technique are used to estimate the soil saturated hydraulic conductivity (Ks. Fractal models with two subset of two (solid and pore and three phases (solid, pore and soil fractal (PSF are used to estimate the fractal dimension of soil particles. The PSF represents a generalization of the solid and pore mass fractal models. The PSF characterizes both the solid and pore phases of the porous material. It also exhibits self-similarity to some degree, in the sense that where local structure seems to be similar to the whole structure.PSF models can estimate interface fractal dimension using soil pore size distribution data (PSD and soil moisture retention curve (SWRC. The main objective of this study was to evaluate different fractal models to estimate the Ksparameter. Materials and Methods: The Schaapetal data was used in this study. The complex consists of sixty soil samples. Soil texture, soil bulk density, soil saturated hydraulic conductivity and soil particle size distribution curve were measured by hydrometer method, undistributed soil sample, constant head method and wet sieve method, respectively for all soil samples.Soil water retention curve were determined by using pressure plates apparatus.The Ks parameter could be estimated by Ralws model as a function of fractal dimension by seven fractal models. Fractal models included Fuentes at al. (1996, Hunt and Gee (2002, Bird et al. (2000, Huang and Zhang (2005, Tyler and Wheatcraft (1990, Kutlu et al. (2008, Sepaskhah and Tafteh (2013.Therefore The Ks parameter can be estimated as a function of the DS (fractal dimension by seven fractal models (Table 2.Sensitivity analysis of Rawls model was assessed by making changes±10%, ±20% and±30%(in input parameters

  7. Influence of the heterogeneity on the hydraulic conductivity of a real aquifer

    Science.gov (United States)

    Carmine, Fallico; Aldo Pedro, Ferrante; Chiara, Vita Maria; Bartolo Samuele, De

    2010-05-01

    Many factors influence the flux in the porous media therefore the values of the representative parameters of the aquifer such as the hydraulic conductivity (k). A lot of studies have shown that this parameter increases with the portion of the aquifer tested. The main cause of this behaviour is the heterogeneity in the aquifer (Sànchez-Vila et al., 1996). It was also verified that the scale dependence of hydraulic conductivity does not depend on the specific method of measurement (Schulze-Makuch and Cherkauer, 1998). An experimental approach to study this phenomenon is based on sets of measurements carried out at different scales. However, one should consider that for the lower scale values k can be determined by direct measurements, performed in the laboratory using samples of different dimensions; whyle, for the large scales the measurement of the hydraulic conductivity requires indirect methods (Johnson and Sen, 1988; Katz and Thompson, 1986; Bernabé and Revil, 1995). In this study the confined aquifer of Montalto Uffugo test field was examined. This aquifer has the geological characteristics of a recently formed valley, with conglomeratic and sandy alluvial deposits; specifically the layer of sands and conglomerates, with a significant percentage of silt at various levels, lies about 55-60 m below the ground surface, where there is a heavy clay formation. Moreover in the test field, for the considered confined aquifer, there are one completely penetrating well, five partially penetrating wells and two completely penetrating piezometers. Along two vertical lines a series of cylindrical samples (6.4 cm of diameter and 15 cm of head) were extracted and for each one of them the k value was measured in laboratory by direct methods, based on the use of flux cells. Also indirect methods were used; in fact, a series of slug tests was carried out, determining the corresponding k values and the radius of influence (R). Moreover another series of pumping tests was

  8. Ear Rachis Xylem Occlusion and Associated Loss in Hydraulic Conductance Coincide with the End of Grain Filling for Wheat.

    Science.gov (United States)

    Neghliz, Hayet; Cochard, Hervé; Brunel, Nicole; Martre, Pierre

    2016-01-01

    Seed dehydration is the normal terminal event in the development of orthodox seeds and is physiologically related to the cessation of grain dry mass accumulation and crop grain yield. For a better understanding of grain dehydration, we evaluated the hypothesis that hydraulic conductance of the ear decreases during the latter stages of development and that this decrease results from disruption or occlusion of xylem conduits. Whole ear, rachis, and stem nodes hydraulic conductance and percentage loss of xylem conductivity were measured from flowering to harvest-ripeness on bread wheat (Triticum aestivum L.) cv. Récital grown under controlled environments. Flag leaf transpiration, stomatal conductance, chlorophyll content and grain and ear water potentials were also measured during grain development. We show that grain dehydration was not related with whole plant physiology and leaf senescence, but closely correlated with the hydraulic properties of the xylem conduits irrigating the grains. Indeed, there was a substantial decrease in rachis hydraulic conductance at the onset of the grain dehydration phase. This hydraulic impairment was not caused by the presence of air embolism in xylem conduits of the stem internodes or rachis but by the occlusion of the xylem lumens by polysaccharides (pectins and callose). Our results demonstrate that xylem hydraulics plays a key role during grain maturation.

  9. Hydraulic conductivity of active layer soils in the McMurdo Dry Valleys, Antarctica: Geological legacy controls modern hillslope connectivity

    Science.gov (United States)

    Schmidt, Logan M.; Levy, Joseph S.

    2017-04-01

    Spatial variability in the hydraulic and physical properties of active layer soils influences shallow groundwater flow through cold-desert hydrological systems. This study measures the saturated hydraulic conductivity and grain-size distribution of 90 soil samples from the McMurdo Dry Valleys (MDV), Antarctica-primarily from Taylor Valley-to determine what processes affect the spatial distribution of saturated hydraulic conductivity in a simple, mineral-soil-dominated natural hillslope laboratory. We find that the saturated hydraulic conductivity and the grain-size distribution of soils are organized longitudinally within Taylor Valley. Soils sampled down-valley near the coast have a higher percentage of fine-sized sediments (fine sand, silt, clay) and lower saturated hydraulic conductivities than soils collected up-valley near Taylor Glacier (1.3 × 10- 2 vs. 1.2 × 10- 1 cm/s). Soils collected mid-valley have intermediate amounts of fines and saturated hydraulic conductivity values consistent with a hydrogeologic gradient spanning the valley from high inland to low near the coast. These results suggest the organization of modern soil properties within Taylor Valley is a relict signature from past glaciations that have deposited soils of decreasing age toward the mouth of the valley, modified by fluvial activity acting along temporal and microclimate gradients.

  10. Sand box experiments with bioclogging of porous media: hydraulic conductivity reductions.

    Science.gov (United States)

    Seifert, Dorte; Engesgaard, Peter

    2012-08-01

    Tracer experiments during clogging and de-clogging experiments in a 2D sand box were via an image analysis used to establish a data set on the relation between changes in hydraulic conductivity (K) and relative porosity (β). Clogging appears to create a finger-like tracer transport, which could be caused by an initial heterogeneous distribution of biomass in the sand box. De-clogging occurs at a slower rate possibly due to the presence of inert biomass that is not affected by the starvation conditions by sudden removal of the substrate source. The tracer front was observed to get disturbed closer and closer to the substrate source during the experiments suggesting that the zone of clogging moved upstream. Three clogging models, K(β), from the literature were tested for their ability to describe the temporal changes in clogging at the scale of the sand box; the model of Clement et al. (1996) that makes no assumption on biomass distribution, the plug formation model of Thullner et al. (2002a), and the biofilm-plug formation model of Vandevivere (1995). The plug formation and biofilm-plug formation models both match the observed changes between the hydraulic conductivity of the sand box and the relative porosity. Unfortunately our experiments did not reach low relative porosities where the two models predict different behaviors. The model by Clement et al. (1996) underestimates clogging.

  11. Estimation of hydraulic conductivity on clay content in soil determined from resistivity data

    Energy Technology Data Exchange (ETDEWEB)

    Shevnin, Vladimir; Delgado-Rodriguez, Omar; Mousatov, Aleksandr [Mexican Petroleum Institute, Mexico, D.F. (Mexico); Ryjov, Albert [Moscow State Geological Prospecting Academy, Geophysical Faculty, Moscow (Russian Federation)

    2006-07-15

    The influence of clay content in sandy and clayey soils on hydraulic conductivity (filtration coefficient) is considered. A review of published experimental data on the relationship of hydraulic conductivity with soil lithology and grain size, as dependent on clay content is presented. Theoretical calculations include clay content. Experimental and calculated data agree, and several approximation formulas for filtration coefficient vs clay content are presented. Clay content in soil is estimated from electric resistivity data obtained from 2D VES interpretation. A two-step method is proposed, the first step including clay content calculating from soil resistivity and groundwater salinity, and the second step including filtration coefficient estimating from clay content. Two applications are presented. [Spanish] El contenido de arcilla en suelos areno-arcillosos influye sobre la permeabilidad hidraulica (coeficiente de filtracion). Se presenta una revision de datos experimentales publicados que relacionan el coeficiente de filtracion con el tipo litologico del suelo y el tamano de las particulas. A partir de calculos teoricos, se modifican las conocidas formulas que relacionan el coeficiente de filtracion con el contenido de arcilla. Se estima el contenido de arcilla a partir de los datos interpretados por el metodo SEV, y se propone un procedimiento para la estimacion del coeficiente de filtracion: (a) calculo del contenido de arcilla a partir de la resistividad del suelo y de la salinidad del agua subterranea, (b) estimacion del coeficiente de filtracion a partir del contenido de arcilla. Se presentan algunos ejemplos de la aplicacion de esta metodologia.

  12. Mapping of Soil Saturated Hydraulic Conductivity in Navroud-Assalem Watershed in Guilan Province

    Directory of Open Access Journals (Sweden)

    M.R. Khaledian

    2016-02-01

    Full Text Available Introduction: With increasing awareness of human beings towards the environment, researchers pay more attention to process and redistribution of water flow and solute transport in the soil and groundwater. Moreover, determination of soil hydraulic conductivity is necessary to determine the runoff from basins. Water movement within the unsaturated zone is often described by the formulae proposed by Richards. To solve this equation, initial and boundary conditions of the hydraulic conductivity and the soil water pressure should be determined as functions of soil water content. Beerkan method was developed to identify retention and hydraulic conductivity curves. In this method, van Gunechten with Burdine condition and Brooks and Corey equations were used to describe water retention and hydraulic conductivity curves. Recognition of the spatial pattern of studied parameter using semivariogram and then preparing zoning map with interpolation methods such as IDW and kriging can help us in relevant watershed management. The aim of this study was to spatial analyze of saturated hydraulic conductivity from 50 infiltration tests at watershed scale using Beerkan method and then preparing zoning map for the Navroud watershed. Materials and Methods: Navroud-Assalem watershed with an area of about 307 km2 is located in the west part of Guilan province, within the city of Talesh. Of the total watershed area of Navroud, about 41 km2 is plains and the rest of it is about 266 km2, corresponding to the mountainous area. The study area includes an area with a height above 130 m. In order to complete the database of the studied watershed the present study was designed to assess soil saturated hydraulic conductivity. In this study, a 2×2 km network was designed in Navroud watershed with a surface area of 307 km2, and then infiltration tests were carried out in each node using single ring of Beerkan. Beerkan method derives shape parameters from particle

  13. The strength/moisture relations and hydraulic conductivity of Mexican tepetate

    Energy Technology Data Exchange (ETDEWEB)

    Nimlos, T.J. (Univ. of Montana, Missoula (USA)); Hillery P.A. (Environmental Information Center, Helena, MT (USA))

    1990-07-01

    Indurated soil material formed from volcanic-ash-flow tuff is widespread in the Pacific rim portions of Latin America. This material is called tepetate in Mexico where, in some areas, all soil overlying tepetate has been removed by erosion, leaving a barren landscape with a very slowly permeable surface that contributes to overland flow and flooding. Reclamation of this land involves ripping to break up the upper part of the tepetate or terracing to retain water so that it may infiltrate. Tepetate strength and hydraulic conductivity influence both treatments. The authors determined the change in tepetate strength with moisture. Unconfined compressive strength of eight typical samples was measured at four moisture contents. Strength declined with increasing moisture, especially in samples of high or moderate strength. These data suggest that tepetate of moderate or high strength should be reclaimed during the wet season, whereas low-strength tepetate can be reclaimed at any season. They also determined tepetate's saturated hydraulic conductivity; it varied from 1.5 {times} 10{sup {minus}7} to 36.0 {times} 10{sup {minus}7} m/s. These low values demonstrate the very slowly permeable nature of tepetate and account for the extensive erosion and flooding frequency.

  14. Control of Leaf Expansion by Nitrogen Nutrition in Sunflower Plants : ROLE OF HYDRAULIC CONDUCTIVITY AND TURGOR.

    Science.gov (United States)

    Radin, J W; Boyer, J S

    1982-04-01

    Nitrogen nutrition strongly affected the growth rate of young sunflower (Helianthus annuus L.) leaves. When plants were grown from seed on either of two levels of N availability, a 33% decrease in tissue N of expanding leaves was associated with a 75% overall inhibition of leaf growth. Almost all of the growth inhibition resulted from a depression of the daytime growth rate. Measurements of pressure-induced water flux through roots showed that N deficiency decreased root hydraulic conductivity by about half. Thus, N deficiency lowered the steady-state water potential of expanding leaves during the daytime when transpiration was occurring. As a result, N-deficient leaves were unable to maintain adequate turgor for growth in the daytime. N deficiency also decreased the hydraulic conductivity for water movement into expanding leaf cells in the absence of transpiration, but growth inhibition at night was much less than in the daytime. N nutrition had no detectable effects on plastic extensibility or the threshold turgor for growth.

  15. Root architecture and hydraulic conductance in nutrient deprived Pistacia lentiscus L. seedlings.

    Science.gov (United States)

    Trubat, Roman; Cortina, Jordi; Vilagrosa, Alberto

    2012-12-01

    Plants respond to low nutrient availability by modifying root morphology and root system topology. Root responses to nitrogen (N) and phosphorus (P) limitation may affect plant capacity to withstand water stress. But studies on the effect of nutrient availability on plant ability to uptake and transport water are scarce. In this study, we assess the effect of nitrogen and phosphorus limitation on root morphology and root system topology in Pistacia lentiscus L seedlings, a common Mediterranean shrub, and relate these changes to hydraulic conductivity of the whole root system. Nitrogen and phosphorus deprivation had no effect on root biomass, but root systems were more branched in nutrient limited seedlings. Total root length was higher in seedlings subjected to phosphorus deprivation. Root hydraulic conductance decreased in nutrient-deprived seedlings, and was related to the number of root junctions but not to other architectural traits. Our study shows that changes in nutrient availability affect seedling water use by modifying root architecture. Changes in nutrient availability should be taken into account when evaluating seedling response to drought.

  16. Comparative Analysis of Soluble Phosphate Amendments for the Remediation of Heavy Metal Contaminants: Effect on Sediment Hydraulic Conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Wellman, Dawn M.; Icenhower, Jonathan P.; Owen, Antionette T.

    2006-07-10

    A series of conventional, saturated column experiments were conducted to evaluate the effect of utilizing in situ phosphate amendments, for subsurface, metal remediation, on sediment hydraulic conductivity. Experiments were conducted under mildly alkaline/calcareous conditions representative of conditions commonly encountered at sites across the arid western United States, which have been used in weapons and fuel production and display significant subsurface contamination. Results indicate the displacement of a single pore volume of either sodium monophosphate or phytic acid amendments causes approximately a 30% decrease in the hydraulic conductivity of the sediment. Long-chain polyphosphate amendments afford no measurable reduction in hydraulic conductivity. These results demonstrate (1) the utility of long-chain polyphosphate amendments for subsurface metal sequestration and (2) the necessity of conducting column experiments to completely evaluate the effects of subsurface remediation.

  17. Variations in hydraulic conductivity with scale of measurement during aquifer tests in heterogeneous, porous carbonate rocks

    Science.gov (United States)

    Schulze-Makuch, Dirk; Cherkauer, Douglas S.

    Previous studies have shown that hydraulic conductivity of an aquifer seems to increase as the portion of the aquifer tested increases. To date, such studies have all relied on different methods to determine hydraulic conductivity at each scale of interest, which raises the possibility that the observed increase in hydraulic conductivity is due to the measurement method, not to the scale. This study analyzes hydraulic conductivity with respect to scale during individual aquifer tests in porous, heterogeneous carbonate rocks in southeastern Wisconsin, USA. Results from this study indicate that hydraulic conductivity generally increases during an individual test as the volume of aquifer impacted increases, and the rate of this increase is the same as the rate of increase determined by using different measurement methods. Thus, scale dependence of hydraulic conductivity during single tests does not depend on the method of measurement. This conclusion is supported by 22 of 26 aquifer tests conducted in porous-flow-dominated carbonate units within the aquifer. Instead, scale dependency is probably caused by heterogeneities within the aquifer, a conclusion supported by digital simulation. All of the observed types of hydraulic-conductivity variations with scale during individual aquifer tests can be explained by a conceptual model of a simple heterogeneous aquifer composed of high-conductivity zones within a low-conductivity matrix. Résumé Certaines études ont montré que la conductivité hydraulique d'un aquifère semble augmenter en même temps que la partie testée de l'aquifère s'étend. Jusqu'à présent, ces études ont toutes reposé sur des méthodes de détermination de la conductivité hydraulique différentes pour chaque niveau d'échelle, ce qui a conduit à penser que l'augmentation observée de la conductivité hydraulique pouvait être due aux méthodes de mesure et non à l'effet d'échelle. Cette étude analyse la conductivité hydraulique par

  18. [Spatial variation characteristics of surface soil water content, bulk density and saturated hydraulic conductivity on Karst slopes].

    Science.gov (United States)

    Zhang, Chuan; Chen, Hong-Song; Zhang, Wei; Nie, Yun-Peng; Ye, Ying-Ying; Wang, Ke-Lin

    2014-06-01

    Surface soil water-physical properties play a decisive role in the dynamics of deep soil water. Knowledge of their spatial variation is helpful in understanding the processes of rainfall infiltration and runoff generation, which will contribute to the reasonable utilization of soil water resources in mountainous areas. Based on a grid sampling scheme (10 m x 10 m) and geostatistical methods, this paper aimed to study the spatial variability of surface (0-10 cm) soil water content, soil bulk density and saturated hydraulic conductivity on a typical shrub slope (90 m x 120 m, projected length) in Karst area of northwest Guangxi, southwest China. The results showed that the surface soil water content, bulk density and saturated hydraulic conductivity had different spatial dependence and spatial structure. Sample variogram of the soil water content was fitted well by Gaussian models with the nugget effect, while soil bulk density and saturated hydraulic conductivity were fitted well by exponential models with the nugget effect. Variability of soil water content showed strong spatial dependence, while the soil bulk density and saturated hydraulic conductivity showed moderate spatial dependence. The spatial ranges of the soil water content and saturated hydraulic conductivity were small, while that of the soil bulk density was much bigger. In general, the soil water content increased with the increase of altitude while it was opposite for the soil bulk densi- ty. However, the soil saturated hydraulic conductivity had a random distribution of large amounts of small patches, showing high spatial heterogeneity. Soil water content negatively (P conductivity, while there was no significant correlation between the soil bulk density and saturated hydraulic conductivity.

  19. Is high-resolution inverse characterization of heterogeneous river bed hydraulic conductivities needed and possible?

    Directory of Open Access Journals (Sweden)

    W. Kurtz

    2013-10-01

    Full Text Available River–aquifer exchange fluxes influence local and regional water balances and affect groundwater and river water quality and quantity. Unfortunately, river–aquifer exchange fluxes tend to be strongly spatially variable, and it is an open research question to which degree river bed heterogeneity has to be represented in a model in order to achieve reliable estimates of river–aquifer exchange fluxes. This research question is addressed in this paper with the help of synthetic simulation experiments, which mimic the Limmat aquifer in Zurich (Switzerland, where river–aquifer exchange fluxes and groundwater management activities play an important role. The solution of the unsaturated–saturated subsurface hydrological flow problem including river–aquifer interaction is calculated for ten different synthetic realities where the strongly heterogeneous river bed hydraulic conductivities (L are perfectly known. Hydraulic head data (100 in the default scenario are sampled from the synthetic realities. In subsequent data assimilation experiments, where L is unknown now, the hydraulic head data are used as conditioning information, with the help of the ensemble Kalman filter (EnKF. For each of the ten synthetic realities, four different ensembles of L are tested in the experiments with EnKF; one ensemble estimates high-resolution L fields with different L values for each element, and the other three ensembles estimate effective L values for 5, 3 or 2 zones. The calibration of higher-resolution L fields (i.e. fully heterogeneous or 5 zones gives better results than the calibration of L for only 3 or 2 zones in terms of reproduction of states, stream–aquifer exchange fluxes and parameters. Effective L for a limited number of zones cannot always reproduce the true states and fluxes well and results in biased estimates of net exchange fluxes between aquifer and stream. Also in case only 10 head data are used for conditioning, the high

  20. Flowing fluid electrical conductivity logging of a deep borehole during and following drilling: estimation of transmissivity, water salinity and hydraulic head of conductive zones

    Science.gov (United States)

    Doughty, Christine; Tsang, Chin-Fu; Rosberg, Jan-Erik; Juhlin, Christopher; Dobson, Patrick F.; Birkholzer, Jens T.

    2016-11-01

    Flowing fluid electrical conductivity (FFEC) logging is a hydrogeologic testing method that is usually conducted in an existing borehole. However, for the 2,500-m deep COSC-1 borehole, drilled at Åre, central Sweden, it was done within the drilling period during a scheduled 1-day break, thus having a negligible impact on the drilling schedule, yet providing important information on depths of hydraulically conductive zones and their transmissivities and salinities. This paper presents a reanalysis of this set of data together with a new FFEC logging data set obtained soon after drilling was completed, also over a period of 1 day, but with a different pumping rate and water-level drawdown. Their joint analysis not only results in better estimates of transmissivity and salinity in the conducting fractures intercepted by the borehole, but also yields the hydraulic head values of these fractures, an important piece of information for the understanding of hydraulic structure of the subsurface. Two additional FFEC logging tests were done about 1 year later, and are used to confirm and refine this analysis. Results show that from 250 to 2,000 m depths, there are seven distinct hydraulically conductive zones with different hydraulic heads and low transmissivity values. For the final test, conducted with a much smaller water-level drawdown, inflow ceased from some of the conductive zones, confirming that their hydraulic heads are below the hydraulic head measured in the wellbore under non-pumped conditions. The challenges accompanying 1-day FFEC logging are summarized, along with lessons learned in addressing them.

  1. Flowing fluid electrical conductivity logging of a deep borehole during and following drilling: estimation of transmissivity, water salinity and hydraulic head of conductive zones

    Science.gov (United States)

    Doughty, Christine; Tsang, Chin-Fu; Rosberg, Jan-Erik; Juhlin, Christopher; Dobson, Patrick F.; Birkholzer, Jens T.

    2017-03-01

    Flowing fluid electrical conductivity (FFEC) logging is a hydrogeologic testing method that is usually conducted in an existing borehole. However, for the 2,500-m deep COSC-1 borehole, drilled at Åre, central Sweden, it was done within the drilling period during a scheduled 1-day break, thus having a negligible impact on the drilling schedule, yet providing important information on depths of hydraulically conductive zones and their transmissivities and salinities. This paper presents a reanalysis of this set of data together with a new FFEC logging data set obtained soon after drilling was completed, also over a period of 1 day, but with a different pumping rate and water-level drawdown. Their joint analysis not only results in better estimates of transmissivity and salinity in the conducting fractures intercepted by the borehole, but also yields the hydraulic head values of these fractures, an important piece of information for the understanding of hydraulic structure of the subsurface. Two additional FFEC logging tests were done about 1 year later, and are used to confirm and refine this analysis. Results show that from 250 to 2,000 m depths, there are seven distinct hydraulically conductive zones with different hydraulic heads and low transmissivity values. For the final test, conducted with a much smaller water-level drawdown, inflow ceased from some of the conductive zones, confirming that their hydraulic heads are below the hydraulic head measured in the wellbore under non-pumped conditions. The challenges accompanying 1-day FFEC logging are summarized, along with lessons learned in addressing them.

  2. Determining the unsaturated hydraulic conductivity of a compacted sand-bentonite mixture under constant volume and free-swell conditions

    CERN Document Server

    Cui, Yu-Jun; Loiseau, Cyril; Delage, Pierre; 10.1016/j.pce.2008.10.017

    2008-01-01

    Highly compacted sand-bentonite mixtures are often considered as possible engineered barriers in deep high-level radioactive waste disposals. In-situ, the saturation of these barriers from their initially unsaturated state is a complex hydro-mechanical coupled process in which temperature effects also play a role. The key parameter of this process is the unsaturated hydraulic conductivity of the barrier. In this paper, isothermal infiltration experiments were conducted to determine the unsaturated hydraulic conductivity according to the instantaneous profile method. To do so, total suction changes were monitored at different locations along the soil specimen by using resistivity relative humidity probes. Three constant volume infiltration tests were conducted showing, unexpectedly, a decrease of the hydraulic conductivity during infiltration. One test performed under free-swell conditions showed the opposite and standard trend. These observations were interpreted in terms of microstructure changes during wett...

  3. Interaction between soil mineralogy and the application of crop residues on aggregate stability and hydraulic conductivity of the soil

    Science.gov (United States)

    Lado, M.; Kiptoon, R.; Bar-Tal, A.; Wakindiki, I. I. C.; Ben-Hur, M.

    2012-04-01

    One of the main goals of modern agriculture is to achieve sustainability by maintaining crop productivity while avoiding soil degradation. Intensive cultivation could lead to a reduction in soil organic matter that could affect the structure stability and hydraulic conductivity of the soil. Moreover, crops extract nutrients from the soil that are taken away from the field when harvested, and as a consequence, the addition of fertilizers to the soil is necessary to maintain crop productivity. One way to deal with these problems is to incorporate crop residues into the soil after harvest. Crop residues are a source of organic matter that could improve soil physical properties, such as aggregate stability and soil hydraulic conductivity. However, this effect could vary according to other soil properties, such as clay content, clay mineralogy, and the presence of other cementing materials in the soil (mainly carbonates and aluminum and iron oxides). In the present work, the interaction between the addition of chickpea crop residues to the soil and clay mineralogy on aggregate stability and saturated hydraulic conductivity were studied. Chickpea plant residues were added at a rate of 0.5% (w/w) to smectitic, kaolinitic, illitic and non-phyllosilicate soils from different regions. The soils without (control) and with chickpea residues were incubated for 0, 3, 7 and 30 days, and the saturated hydraulic conductivity of the soils was measured in columns after each incubation time. The response of hydraulic conductivity to the addition of residues and incubation time was different in the soils with various mineralogies, although in general, the addition of chickpea residues increased the saturated hydraulic conductivity as compared with the control soils. This positive effect of crop residues on hydraulic conductivity was mainly a result of improved aggregate stability and resistance to slaking during wetting.

  4. Measurement of hydraulic conductivity and water retention curves for different methods and prediction of soil physical properties by kriging

    OpenAIRE

    Eurileny Lucas de Almeida

    2013-01-01

    Knowledge of the physical and hydraulic properties of the soil and its spatial dependence is important because it allows you to perform the zoning of the area in plots that receive differentiated management. This work was divided into three chapters whose general objective is to measure the hydraulic conductivity and water retention curve in soil by different methods and by using the Kriging, draw maps of soil physical attributes of the Irrigation Perimeter Baixo AcaraÃ. To obtain the water r...

  5. Verification of combined thermal-hydraulic and heat conduction analysis code FLOWNET/TRUMP

    Science.gov (United States)

    Maruyama, Soh; Fujimoto, Nozomu; Kiso, Yoshihiro; Murakami, Tomoyuki; Sudo, Yukio

    1988-09-01

    This report presents the verification results of the combined thermal-hydraulic and heat conduction analysis code, FLOWNET/TRUMP which has been utilized for the core thermal hydraulic design, especially for the analysis of flow distribution among fuel block coolant channels, the determination of thermal boundary conditions for fuel block stress analysis and the estimation of fuel temperature in the case of fuel block coolant channel blockage accident in the design of the High Temperature Engineering Test Reactor(HTTR), which the Japan Atomic Energy Research Institute has been planning to construct in order to establish basic technologies for future advanced very high temperature gas-cooled reactors and to be served as an irradiation test reactor for promotion of innovative high temperature new frontier technologies. The verification of the code was done through the comparison between the analytical results and experimental results of the Helium Engineering Demonstration Loop Multi-channel Test Section(HENDEL T(sub 1-M)) with simulated fuel rods and fuel blocks.

  6. Deep rooting plants influence on soil hydraulic properties and air conductivity over time

    Science.gov (United States)

    Uteau, Daniel; Peth, Stephan; Diercks, Charlotte; Pagenkemper, Sebastian; Horn, Rainer

    2014-05-01

    Crop sequences are commonly suggested as an alternative to improve subsoil structure. A well structured soil can be characterized by enhanced transport properties. Our main hypothesis was, that different root systems can modify the soil's macro/mesopore network if enough cultivation time is given. We analyzed the influence of three crops with either shallower roots (Festuca arundinacea, fescue) or taproots (Cichorium intybus, chicory and Medicago sativa, alfalfa). The crops where cultivated on a Haplic Luvisol near Bonn (Germany) for one, two or three years. Undisturbed soil cores were taken for measurement of unsaturated hydraulic conductivity and air permeability. The unsaturated conductivity was measured using the evaporation method, monitoring the water content and tension at two depths of each undisturbed soil core. The van Genuchten-Mualem model (1991) was fitted to the measured data. Air permeability was measured in a permeameter with constant flow at low pressure gradient. The measurements were repeated at -1, -3, -6, -15, -30 and -50 kPa matric tension and the model of Ball et al. (1988) was used to describe permeability as function of matric tension. Furthermore, the cores equilibrated at -15 kPa matric tension were scanned with X-Ray computer tomography. By means of 3D image analysis, geometrical features as pore size distribution, tortuosity and connectivity of the pore network was analyzed. The measurements showed an increased unsaturated hydraulic conductivity associated to coarser pores at the taprooted cultivations. A enhanced pore system (related to shrink-swell processes) under alfalfa was observed in both transport measurements and was confirmed by the 3D image analysis. This highly functional pore system (consisting mainly of root paths, earthworm channels and shrinking cracks) was clearly visible below the 75 cm of depth and differentiated significantly from the other two treatments only after three years of cultivation, which shows the time

  7. Evolution of neural networks for the prediction of hydraulic conductivity as a function of borehole geophysical logs: Shobasama site, Japan.

    Energy Technology Data Exchange (ETDEWEB)

    Reeves, Paul C.; McKenna, Sean Andrew

    2004-06-01

    This report describes the methodology and results of a project to develop a neural network for the prediction of the measured hydraulic conductivity or transmissivity in a series of boreholes at the Tono, Japan study site. Geophysical measurements were used as the input to EL feed-forward neural network. A simple genetic algorithm was used to evolve the architecture and parameters of the neural network in conjunction with an optimal subset of geophysical measurements for the prediction of hydraulic conductivity. The first attempt was focused on the estimation of the class of the hydraulic conductivity, high, medium or low, from the geophysical logs. This estimation was done while using the genetic algorithm to simultaneously determine which geophysical logs were the most important and optimizing the architecture of the neural network. Initial results showed that certain geophysical logs provided more information than others- most notably the 'short-normal', micro-resistivity, porosity and sonic logs provided the most information on hydraulic conductivity. The neural network produced excellent training results with accuracy of 90 percent or greater, but was unable to produce accurate predictions of the hydraulic conductivity class. The second attempt at prediction was done using a new methodology and a modified data set. The new methodology builds on the results of the first attempts at prediction by limiting the choices of geophysical logs to only those that provide significant information. Additionally, this second attempt uses a modified data set and predicts transmissivity instead of hydraulic conductivity. Results of these simulations indicate that the most informative geophysical measurements for the prediction of transmissivity are depth and sonic log. The long normal resistivity and self potential borehole logs are moderately informative. In addition, it was found that porosity and crack counts (clear, open, or hairline) do not inform predictions

  8. Detection of QTL for exudation rate at ripening stage in rice and its contribution to hydraulic conductance.

    Science.gov (United States)

    Yamamoto, Toshio; Suzuki, Tadafumi; Suzuki, Kenji; Adachi, Shunsuke; Sun, Jian; Yano, Masahiro; Ookawa, Taiichiro; Hirasawa, Tadashi

    2016-01-01

    Dry matter production of crops is determined by how much light they intercept and how efficiently they use it for carbon fixation; i.e., photosynthesis. The high-yielding rice cultivar, Akenohoshi, maintains a high photosynthetic rate in the middle of the day owing to its high hydraulic conductance in comparison with the elite commercial rice cultivar, Koshihikari. We developed 94 recombinant inbred lines derived from Akenohoshi and Koshihikari and measured their exudation rate to calculate hydraulic conductance to osmotic water transport in a paddy field. A quantitative trait locus (QTL) for exudation rate was detected on the long arm of chromosome 2 at the heading and ripening stages. We developed chromosome segment substitution lines which carried Akenohoshi segments in the Koshihikari genetic background, and measured hydraulic conductance to both osmotic and passive water transport. The QTL was confirmed to be located within a region of about 4.2Mbp on the distal end of long arm of chromosome 2. The Akenohoshi allele increased root surface area and hydraulic conductance, but didn't increase hydraulic conductivity of a plant.

  9. Transport of heavy metals and chemical compatibility of hydraulic conductivity of a compacted sand-bentonite mixture

    Directory of Open Access Journals (Sweden)

    Nanthanit Charoenthaisong

    2008-03-01

    Full Text Available Clayey soils are usually used as barrier material in landfill liners because of its low hydraulic conductivity and high sorption capacity. Bentonite, which consists mainly of montmorillonite, has a high cation exchange capacity resulting in a high retention capacity of heavy metals. Sand is a permeable material but its hydraulic conductivity decreases significantly when mixed with bentonite. However, using a sand-bentonite mixture as landfill liners is questionable, because the hydraulic conductivity of the sand-bentonite mixture may increase when permeated with heavy metal solutions, which are normally found in landfill leachates. In this paper, transport of heavy metals through a compacted sand-bentonite mixture and its chemical compatibility were studied through the batch adsorption test, the column test, and the hydraulic conductivity test.Experimental results indicate that the sorption capacity of the bentonite, ranked in descending order, was Cr3+, Pb2+, Cd2+, Zn2+, and Ni2+, respectively. The diffusion coefficients of the sand-bentonite mixture were in the order of 10-5 cm2/s and the retardation factors were 130, 115, 111, and 90 for Pb2+, Ni2+, Zn2+, and Cd2+, respectively. The hydraulic conductivity of thesand-bentonite mixture was only compatible with a chromium solution having a concentration not greater than 0.001 M.

  10. A Numerical Method for the Estimation of Distributed Hydraulic Conductivity Using Richards Equation

    Science.gov (United States)

    Cockett, R.; Haber, E.

    2013-12-01

    Characterizing groundwater flow in the vadose zone has many important and practical applications in near surface hydrogeology. The spatial estimation of the hydraulic conductivity function, which is the regulator of unsaturated groundwater flow, is an critical step in any hydrogeologic site characterization. However, this estimation is difficult and simplifications are consistently used to avert these conceptual and computational difficulties. Comprehensive time-lapse data of in situ saturations, or proxies of saturation from geophysical methods, are increasingly available. Using these large data sets appropriately, and maximizing the utility of the data to recover estimates of heterogeneous hydraulic conductivity, requires innovative numerical methods. This inverse problem has been approached in many different ways in the literature from stochastic methods to various gradient based methods. However, the way in which the computational complexity of the inverse method scales becomes important as problem size increases; as computational memory and time often become the bottleneck of solving the inverse problem when the problem is solved for heterogeneous hydraulic conductivity in two- and particularly in three-dimensions. For the inverse problem involving Richards equation, some version of a Gauss-Newton method (e.g. Levenberg-Marquardt) with a direct calculation of the sensitivity matrix is commonly used. However, while these approaches allow to deal with moderate scale problems they have one major drawback: the sensitivity matrix is a large dense matrix and its computation requires dense linear algebra and, for large scale problems, a non-trivial amount of storage. Furthermore, previous work use either numerical or automatic differentiation in order to compute the sensitivity matrix and this can generate inaccuracies in its computation and tarry convergence of the optimization algorithm. We suggest a modern numerical method that allows for the solution of the

  11. Treated wastewater irrigation effects on soil hydraulic conductivity and aggregate stability of loamy soils in Israel

    Directory of Open Access Journals (Sweden)

    Schacht Karsten

    2015-03-01

    Full Text Available The use of treated wastewater (TWW for agricultural irrigation becomes increasingly important in water stressed regions like the Middle East for substituting fresh water (FW resources. Due to elevated salt concentrations and organic compounds in TWW this practice has potential adverse effects on soil quality, such as the reduction of hydraulic conductivity (HC and soil aggregate stability (SAS. To assess the impact of TWW irrigation in comparison to FW irrigation on HC, in-situ infiltration measurements using mini disk infiltrometer were deployed in four different long-term experimental orchard test sites in Israel. Topsoil samples (0-10 cm were collected for analyzing SAS and determination of selected soil chemical and physical characteristics.

  12. Modeling Flow Rate to Estimate Hydraulic Conductivity in a Parabolic Ceramic Water Filter

    Directory of Open Access Journals (Sweden)

    Ileana Wald

    2012-01-01

    Full Text Available In this project we model volumetric flow rate through a parabolic ceramic water filter (CWF to determine how quickly it can process water while still improving its quality. The volumetric flow rate is dependent upon the pore size of the filter, the surface area, and the height of water in the filter (hydraulic head. We derive differential equations governing this flow from the conservation of mass principle and Darcy's Law and find the flow rate with respect to time. We then use methods of calculus to find optimal specifications for the filter. This work is related to the research conducted in Dr. James R. Mihelcic's Civil and Environmental Engineering Lab at USF.

  13. Scale-dependency of effective hydraulic conductivity on fire-affected hillslopes

    Science.gov (United States)

    Langhans, Christoph; Lane, Patrick N. J.; Nyman, Petter; Noske, Philip J.; Cawson, Jane G.; Oono, Akiko; Sheridan, Gary J.

    2016-07-01

    Effective hydraulic conductivity (Ke) for Hortonian overland flow modeling has been defined as a function of rainfall intensity and runon infiltration assuming a distribution of saturated hydraulic conductivities (Ks). But surface boundary condition during infiltration and its interactions with the distribution of Ks are not well represented in models. As a result, the mean value of the Ks distribution (KS¯), which is the central parameter for Ke, varies between scales. Here we quantify this discrepancy with a large infiltration data set comprising four different methods and scales from fire-affected hillslopes in SE Australia using a relatively simple yet widely used conceptual model of Ke. Ponded disk (0.002 m2) and ring infiltrometers (0.07 m2) were used at the small scales and rainfall simulations (3 m2) and small catchments (ca 3000 m2) at the larger scales. We compared KS¯ between methods measured at the same time and place. Disk and ring infiltrometer measurements had on average 4.8 times higher values of KS¯ than rainfall simulations and catchment-scale estimates. Furthermore, the distribution of Ks was not clearly log-normal and scale-independent, as supposed in the conceptual model. In our interpretation, water repellency and preferential flow paths increase the variance of the measured distribution of Ks and bias ponding toward areas of very low Ks during rainfall simulations and small catchment runoff events while areas with high preferential flow capacity remain water supply-limited more than the conceptual model of Ke predicts. The study highlights problems in the current theory of scaling runoff generation.

  14. FRACTAL SCALING OF PARTICLE AND PORE SIZE DISTRIBUTIONS AND ITS RELATION TO SOIL HYDRAULIC CONDUCTIVITY

    Directory of Open Access Journals (Sweden)

    BACCHI O.O.S.

    1996-01-01

    Full Text Available Fractal scaling has been applied to soils, both for void and solid phases, as an approach to characterize the porous arrangement, attempting to relate particle-size distribution to soil water retention and soil water dynamic properties. One important point of such an analysis is the assumption that the void space geometry of soils reflects its solid phase geometry, taking into account that soil pores are lined by the full range of particles, and that their fractal dimension, which expresses their tortuosity, could be evaluated by the fractal scaling of particle-size distribution. Other authors already concluded that although fractal scaling plays an important role in soil water retention and porosity, particle-size distribution alone is not sufficient to evaluate the fractal structure of porosity. It is also recommended to examine the relationship between fractal properties of solids and of voids, and in some special cases, look for an equivalence of both fractal dimensions. In the present paper data of 42 soil samples were analyzed in order to compare fractal dimensions of pore-size distribution, evaluated by soil water retention curves (SWRC of soils, with fractal dimensions of soil particle-size distributions (PSD, taking the hydraulic conductivity as a standard variable for the comparison, due to its relation to tortuosity. A new procedure is proposed to evaluate the fractal dimension of pore-size distribution. Results indicate a better correlation between fractal dimensions of pore-size distribution and the hydraulic conductivity for this set of soils, showing that for most of the soils analyzed there is no equivalence of both fractal dimensions. For most of these soils the fractal dimension of particle-size distribution does not indicate properly the pore trace tortuosity. A better equivalence of both fractal dimensions was found for sandy soils.

  15. Gamma ray transmission for hydraulic conductivity measurement of undisturbed soil columns

    Directory of Open Access Journals (Sweden)

    Anderson Camargo Moreira

    2007-03-01

    Full Text Available This work had the objective to determine the Hydraulic Conductivity K(theta function for different depth levels z, of columns of undisturbed soil, using the gamma ray transmission technique applied to the Sisson method. The results indicated a growing behavior for K(theta and a homogeneous soil density, both in relation to the increase of the depth. The methodology of gamma ray transmission showed satisfactory results on the determination of the hydraulic conductivity in columns of undisturbed soil, besides being very reliable and a nondestructive method.O estudo da condutividade hidráulica para solos não saturados é essencial quando aplicado às situações relacionadas à irrigação, drenagem e transporte de nutrientes no solo, é uma importante propriedade para desenvolvimentos de culturas agrícolas. Este trabalho tem o objetivo de determinar a função Condutividade Hidráulica K(teta, em diferentes níveis z de profundidade, em colunas de solo indeformado, utilizando a transmissão de raios gama aplicada ao método de Sisson. Os resultados indicam um comportamento crescente para K(teta e uma densidade de solo homogênea, ambos em relação ao aumento da profundidade. A metodologia de transmissão de raios gama mostrou resultados bastante satisfatórios na determinação da condutividade hidráulica em colunas de solo indeformado, além de ser muito confiável e não destrutivo.

  16. A global data set of soil hydraulic properties and sub-grid variability of soil water retention and hydraulic conductivity curves

    Science.gov (United States)

    Montzka, Carsten; Herbst, Michael; Weihermüller, Lutz; Verhoef, Anne; Vereecken, Harry

    2017-07-01

    Agroecosystem models, regional and global climate models, and numerical weather prediction models require adequate parameterization of soil hydraulic properties. These properties are fundamental for describing and predicting water and energy exchange processes at the transition zone between solid earth and atmosphere, and regulate evapotranspiration, infiltration and runoff generation. Hydraulic parameters describing the soil water retention (WRC) and hydraulic conductivity (HCC) curves are typically derived from soil texture via pedotransfer functions (PTFs). Resampling of those parameters for specific model grids is typically performed by different aggregation approaches such a spatial averaging and the use of dominant textural properties or soil classes. These aggregation approaches introduce uncertainty, bias and parameter inconsistencies throughout spatial scales due to nonlinear relationships between hydraulic parameters and soil texture. Therefore, we present a method to scale hydraulic parameters to individual model grids and provide a global data set that overcomes the mentioned problems. The approach is based on Miller-Miller scaling in the relaxed form by Warrick, that fits the parameters of the WRC through all sub-grid WRCs to provide an effective parameterization for the grid cell at model resolution; at the same time it preserves the information of sub-grid variability of the water retention curve by deriving local scaling parameters. Based on the Mualem-van Genuchten approach we also derive the unsaturated hydraulic conductivity from the water retention functions, thereby assuming that the local parameters are also valid for this function. In addition, via the Warrick scaling parameter λ, information on global sub-grid scaling variance is given that enables modellers to improve dynamical downscaling of (regional) climate models or to perturb hydraulic parameters for model ensemble output generation. The present analysis is based on the ROSETTA PTF

  17. A global data set of soil hydraulic properties and sub-grid variability of soil water retention and hydraulic conductivity curves

    Directory of Open Access Journals (Sweden)

    C. Montzka

    2017-07-01

    Full Text Available Agroecosystem models, regional and global climate models, and numerical weather prediction models require adequate parameterization of soil hydraulic properties. These properties are fundamental for describing and predicting water and energy exchange processes at the transition zone between solid earth and atmosphere, and regulate evapotranspiration, infiltration and runoff generation. Hydraulic parameters describing the soil water retention (WRC and hydraulic conductivity (HCC curves are typically derived from soil texture via pedotransfer functions (PTFs. Resampling of those parameters for specific model grids is typically performed by different aggregation approaches such a spatial averaging and the use of dominant textural properties or soil classes. These aggregation approaches introduce uncertainty, bias and parameter inconsistencies throughout spatial scales due to nonlinear relationships between hydraulic parameters and soil texture. Therefore, we present a method to scale hydraulic parameters to individual model grids and provide a global data set that overcomes the mentioned problems. The approach is based on Miller–Miller scaling in the relaxed form by Warrick, that fits the parameters of the WRC through all sub-grid WRCs to provide an effective parameterization for the grid cell at model resolution; at the same time it preserves the information of sub-grid variability of the water retention curve by deriving local scaling parameters. Based on the Mualem–van Genuchten approach we also derive the unsaturated hydraulic conductivity from the water retention functions, thereby assuming that the local parameters are also valid for this function. In addition, via the Warrick scaling parameter λ, information on global sub-grid scaling variance is given that enables modellers to improve dynamical downscaling of (regional climate models or to perturb hydraulic parameters for model ensemble output generation. The present analysis is based

  18. A mini slug test method for determination of a local hydraulic conductivity of an unconfined sandy aquifer

    DEFF Research Database (Denmark)

    Hinsby, Klaus; Bjerg, Poul Løgstrup; Andersen, Lars J.;

    1992-01-01

    from level to level and thereby establish vertical profiles of the hydraulic conductivity. The head data from the test well are recorded with a 10 mm pressure transducer, and the initial head difference required is established by a small vacuum pump. The method described has provided 274 spatially......A new and efficient mini slug test method for the determination of local hydraulic conductivities in unconfined sandy aquifers is developed. The slug test is performed in a small-diameter (1 inch) driven well with a 0.25 m screen just above the drive point. The screened drive point can be driven...... distributed measurements of a local hydraulic conductivity at a tracer test site at Vejen, Denmark. The mini slug test results calculated by a modified Dax slug test analysing method, applying the elastic storativity in the Dax equations instead of the specific yield, are in good accordance with the results...

  19. Saturated hydraulic conductivity determined by on ground mono-offset Ground-Penetrating Radar inside a single ring infiltrometer

    CERN Document Server

    Léger, Emmanuel; Coquet, Yves

    2013-01-01

    In this study we show how to use GPR data acquired along the infiltration of water inside a single ring infiltrometer to inverse the saturated hydraulic conductivity. We used Hydrus-1D to simulate the water infiltration. We generated water content profiles at each time step of infiltration, based on a particular value of the saturated hydraulic conductivity, knowing the other van Genuchten parameters. Water content profiles were converted to dielectric permittivity profiles using the Complex Refractive Index Method relation. We then used the GprMax suite of programs to generate radargrams and to follow the wetting front using arrival time of electromagnetic waves recorded by a Ground-Penetrating Radar (GPR). Theoretically, the 1D time convolution between reflectivity and GPR signal at any infiltration time step is related to the peak of the reflected amplitude recorded in the corresponding trace in the radargram. We used this relation ship to invert the saturated hydraulic conductivity for constant and fallin...

  20. Biochar-Induced Changes in Soil Hydraulic Conductivity and Dissolved Nutrient Fluxes Constrained by Laboratory Experiments

    Science.gov (United States)

    Barnes, Rebecca T.; Gallagher, Morgan E.; Masiello, Caroline A.; Liu, Zuolin; Dugan, Brandon

    2014-01-01

    The addition of charcoal (or biochar) to soil has significant carbon sequestration and agronomic potential, making it important to determine how this potentially large anthropogenic carbon influx will alter ecosystem functions. We used column experiments to quantify how hydrologic and nutrient-retention characteristics of three soil materials differed with biochar amendment. We compared three homogeneous soil materials (sand, organic-rich topsoil, and clay-rich Hapludert) to provide a basic understanding of biochar-soil-water interactions. On average, biochar amendment decreased saturated hydraulic conductivity (K) by 92% in sand and 67% in organic soil, but increased K by 328% in clay-rich soil. The change in K for sand was not predicted by the accompanying physical changes to the soil mixture; the sand-biochar mixture was less dense and more porous than sand without biochar. We propose two hydrologic pathways that are potential drivers for this behavior: one through the interstitial biochar-sand space and a second through pores within the biochar grains themselves. This second pathway adds to the porosity of the soil mixture; however, it likely does not add to the effective soil K due to its tortuosity and smaller pore size. Therefore, the addition of biochar can increase or decrease soil drainage, and suggests that any potential improvement of water delivery to plants is dependent on soil type, biochar amendment rate, and biochar properties. Changes in dissolved carbon (C) and nitrogen (N) fluxes also differed; with biochar increasing the C flux from organic-poor sand, decreasing it from organic-rich soils, and retaining small amounts of soil-derived N. The aromaticity of C lost from sand and clay increased, suggesting lost C was biochar-derived; though the loss accounts for only 0.05% of added biochar-C. Thus, the direction and magnitude of hydraulic, C, and N changes associated with biochar amendments are soil type (composition and particle size) dependent

  1. Determination of hydraulic conductivity of fractured rock masses:A case study for a rock cavern project in Singapore

    Institute of Scientific and Technical Information of China (English)

    Zhipeng Xu; Zhiye Zhao; Jianping Sun; Ming Lu

    2015-01-01

    In order to reduce the risk associated with water seepage in an underground rock cavern project in Singapore, a reliable hydro-geological model should be established based on the in situ investigation data. The key challenging issue in the hydro-geological model building is how to integrate limited geological and hydro-geological data to determine the hydraulic conductivity of the fractured rock masses. Based on the data obtained from different stages (feasibility investigation stage, construction stage, and post-construction stage), suitable models and methods are proposed to determine the hy-draulic conductivities at different locations and depths, which will be used at other locations in the future.

  2. Impact of treated wastewater on growth, respiration and hydraulic conductivity of citrus root systems in light and heavy soils.

    Science.gov (United States)

    Paudel, Indira; Cohen, Shabtai; Shaviv, Avi; Bar-Tal, Asher; Bernstein, Nirit; Heuer, Bruria; Ephrath, Jhonathan

    2016-06-01

    Roots interact with soil properties and irrigation water quality leading to changes in root growth, structure and function. We studied these interactions in an orchard and in lysimeters with clay and sandy loam soils. Minirhizotron imaging and manual sampling showed that root growth was three times lower in the clay relative to sandy loam soil. Treated wastewater (TWW) led to a large reduction in root growth with clay (45-55%) but not with sandy loam soil (hydraulic conductivity was severely reduced in clay soil. Treated wastewater increased respiration rate and reduced hydraulic conductivity of all root orders in clay but only of the lower root orders in sandy loam soil. Loss of hydraulic conductivity increased with root order in clay and clay irrigated with TWW. Respiration and hydraulic properties of all root orders were significantly affected by sodium-amended TWW in sandy loam soil. These changes in root order morphology, anatomy, physiology and hydraulic properties indicate rapid and major modifications of root systems in response to differences in soil type and water quality.

  3. Effect of the method of estimation of soil saturated hydraulic conductivity with regards to the design of stormwater infiltration trenches

    Science.gov (United States)

    Paiva coutinho, Artur; Predelus, Dieuseul; Lassabatere, Laurent; Ben Slimene, Erij; Celso Dantas Antonino, Antonio; Winiarski, Thierry; Joaquim da Silva Pereira Cabral, Jaime; Angulo-Jaramillo, Rafael

    2014-05-01

    Best management practices are based on the infiltration of stormwater (e.g. infiltration into basins or trenches) to reduce the risk of flooding of urban areas. Proper estimations of saturated hydraulic conductivity of the vadose zone are required to avoid inappropriate design of infiltration devices. This article aims at assessing (i) the method-dependency of the estimation of soils saturated hydraulic conductivity and (ii) the consequences of such dependency on the design of infiltration trenches. This is illustrated for the specific case of an infiltration trench to be constructed to receive stormwater from a specific parking surface, 250 m2 in area, in Recife (Brazil). Water infiltration experiments were conducted according to the Beerkan Method, i.e. application of a zero water pressure head through a disc source (D=15 cm) and measures of the amount of infiltrated water with time. Saturated hydraulic conductivity estimates are derived from the analysis of these infiltration tests using several different conceptual approaches: one-dimensional models of Horton(1933) and Philip(1957), three-dimensional methods recently developed (Lassabatere et al., 2006, Wu et al., 1999, and Bagarello et al., 2013) and direct 3-dimensional numerical inversion. The estimations for saturated hydraulic conductivity ranged between 65.5 mm/h and 94 mm/h for one-dimensional methods, whereas using three-dimensional methods saturated hydraulic conductivity ranged between 15.6 mm/h and 50 mm/h. These results shows the need for accounting for 3D geometry, and more generally, the physics of water infiltration in soils, if a proper characterization of soil saturated hydraulic conductivity is targeted. In a second step, each estimate of the saturated hydraulic conductivity was used to calculate the stormwater to be stored in the studied trench for several rainfall events of recurrence intervals of 2 to 25 years. The calculation of these volumes showed a great sensitivity with regards to the

  4. Steady-state discharge into tunnels in formations with random variability and depth-decaying trend of hydraulic conductivity

    Science.gov (United States)

    Jiang, Xiao-Wei; Wan, Li; Yeh, Tian-Chyi Jim; Wang, Xu-Sheng; Xu, Liang

    2010-06-01

    SummaryMulti-scale heterogeneity of geological formations is a rule, which consists of random (local-scale) and systematic (large-scale) variability of hydraulic conductivity. The random variability and depth-decaying trend, a systematic variability, have different effects on subsurface flow, thus on groundwater discharge into tunnels. Little research has examined this problem in the past. Using Monte Carlo simulation and information of statistics of heterogeneity, we evaluate the most likely (ensemble average) discharge rate into a tunnel in geologic media with the multi-scale heterogeneity and uncertainty associated with this estimate. We find that the ensemble average discharge rate is larger than the discharge rate predicted by geometric mean of hydraulic conductivity, and smaller than the discharge rate predicted by arithmetic mean of hydraulic conductivity. Moreover, the ensemble average discharge rate decreases with the decay exponent of the depth-decaying trend, and increases with the standard deviation as well as the correlation scale of the stationary log-conductivity fields. We also find that the discharge rate of a tunnel is highly influenced by the hydraulic conductivity near the tunnel. Furthermore, deviation of the true discharge rate from the ensemble average can be large and increases with the decay exponent, standard deviation and correlation scale of log-conductivity fields. The largest uncertainty of discharge rate prediction in the shallow subsurface is controlled by the variability of conductivity fields and the uncertainty at the deep subsurface is by the depth-decaying trend of hydraulic conductivity. Therefore, accurate prediction of groundwater discharge into tunnels requires detailed characterization of multi-scale heterogeneity.

  5. Hydraulic bridges in unsaturated coarse granular media: Influence of bridge size and conductivity on flow through clasts

    Science.gov (United States)

    Jayakody, Jeevan A.; Nicholl, Michael J.

    2016-10-01

    Unsaturated flow in coarse granular media must pass through hydraulic bridges (e.g., pendular water, porous connections) that form a physical connection between adjoining clasts. Previous studies suggest that volumetric flow through a porous clast (Q) will be linearly dependent on the cross-sectional area of the hydraulic bridges, and understate the importance of bridge conductivity. Numerical simulations were performed to explore steady-state flow through a spherical clast with identical bridges located at the top and bottom. The cross-sectional area of the bridges relative to that of the clast (Ar) was varied across six orders of magnitude. The ratio of hydraulic conductivity between bridges and clasts (Kb/Kc) was varied across 12 orders of magnitude to consider resistive, neutral, and conductive bridges. Results show that hydraulic bridges place a primary control on both Q and flux distribution within the clast. For neutral and conductive bridges (Kb/Kc ≥1), Ar is the dominant factor in determining Q, while Kb/Kc is the primary control for resistive bridges (Kb/Kc < 1). For all bridges, Q shows a non-linear dependency on both Ar and Kb/Kc. The intra-clast flow distribution shifts outwards as Ar increases. Conductive bridges promote this process and resistive bridges impede it.

  6. Mind the bubbles: achieving stable measurements of maximum hydraulic conductivity through woody plant samples.

    Science.gov (United States)

    Espino, Susana; Schenk, H Jochen

    2011-01-01

    The maximum specific hydraulic conductivity (k(max)) of a plant sample is a measure of the ability of a plants' vascular system to transport water and dissolved nutrients under optimum conditions. Precise measurements of k(max) are needed in comparative studies of hydraulic conductivity, as well as for measuring the formation and repair of xylem embolisms. Unstable measurements of k(max) are a common problem when measuring woody plant samples and it is commonly observed that k(max) declines from initially high values, especially when positive water pressure is used to flush out embolisms. This study was designed to test five hypotheses that could potentially explain declines in k(max) under positive pressure: (i) non-steady-state flow; (ii) swelling of pectin hydrogels in inter-vessel pit membranes; (iii) nucleation and coalescence of bubbles at constrictions in the xylem; (iv) physiological wounding responses; and (v) passive wounding responses, such as clogging of the xylem by debris. Prehydrated woody stems from Laurus nobilis (Lauraceae) and Encelia farinosa (Asteraceae) collected from plants grown in the Fullerton Arboretum in Southern California, were used to test these hypotheses using a xylem embolism meter (XYL'EM). Treatments included simultaneous measurements of stem inflow and outflow, enzyme inhibitors, stem-debarking, low water temperatures, different water degassing techniques, and varied concentrations of calcium, potassium, magnesium, and copper salts in aqueous measurement solutions. Stable measurements of k(max) were observed at concentrations of calcium, potassium, and magnesium salts high enough to suppress bubble coalescence, as well as with deionized water that was degassed using a membrane contactor under strong vacuum. Bubble formation and coalescence under positive pressure in the xylem therefore appear to be the main cause for declining k(max) values. Our findings suggest that degassing of water is essential for achieving stable and

  7. Design and Construction of Experiment for Direct Electron Irradiation of Uranyl Sulfate Solution: Bubble Formation and Thermal Hydraulics Studies

    Energy Technology Data Exchange (ETDEWEB)

    Chemerisov, Sergey [Argonne National Lab. (ANL), Argonne, IL (United States); Gromov, Roman [Argonne National Lab. (ANL), Argonne, IL (United States); Makarashvili, Vakho [Argonne National Lab. (ANL), Argonne, IL (United States); Heltemes, Thad [Argonne National Lab. (ANL), Argonne, IL (United States); Sun, Zaijing [Argonne National Lab. (ANL), Argonne, IL (United States); Wardle, Kent E. [Argonne National Lab. (ANL), Argonne, IL (United States); Bailey, James [Argonne National Lab. (ANL), Argonne, IL (United States); Quigley, Kevin [Argonne National Lab. (ANL), Argonne, IL (United States); Stepinski, Dominique [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, George [Argonne National Lab. (ANL), Argonne, IL (United States)

    2014-10-01

    Argonne is assisting SHINE Medical Technologies in developing SHINE, a system for producing fission-product 99Mo using a D/T-accelerator to produce fission in a non-critical target solution of aqueous uranyl sulfate. We have developed an experimental setup for studying thermal-hydraulics and bubble formation in the uranyl sulfate solution to simulate conditions expected in the SHINE target solution during irradiation. A direct electron beam from the linac accelerator will be used to irradiate a 20 L solution (sector of the solution vessel). Because the solution will undergo radiolytic decomposition, we will be able to study bubble formation and dynamics and effects of convection and temperature on bubble behavior. These experiments will serve as a verification/ validation tool for the thermal-hydraulic model. Utilization of the direct electron beam for irradiation allows homogeneous heating of a large solution volume and simplifies observation of the bubble dynamics simultaneously with thermal-hydraulic data collection, which will complement data collected during operation of the miniSHINE experiment. Irradiation will be conducted using a 30-40 MeV electron beam from the high-power linac accelerator. The total electron-beam power will be 20 kW, which will yield a power density on the order of 1 kW/L. The solution volume will be cooled on the front and back surfaces and central tube to mimic the geometry of the proposed SHINE solution vessel. Also, multiple thermocouples will be inserted into the solution vessel to map thermal profiles. The experimental design is now complete, and installation and testing are in progress.

  8. The effects of sustained forest use on hillslope soil hydraulic conductivity in the Middle Mountains of Central Nepal

    NARCIS (Netherlands)

    Ghimire, C.P.; Bruijnzeel, L. Adrian; Bonell, Mike; Coles, Neil A.; Lubczynski, M.; Gilmour, Don A.

    2013-01-01

    This work investigated the multi-decadal changes in field saturated hydraulic conductivity, Kfs, beneath severely degraded pasture, natural forest and two mature planted Pinus roxburghii stands between two sets of measurements made in 1986 and 2011 at the same locations in the Middle Mountains of

  9. Evaluation of clogging in planted and unplanted horizontal subsurface flow constructed wetlands: solids accumulation and hydraulic conductivity reduction.

    Science.gov (United States)

    De Paoli, André Cordeiro; von Sperling, Marcos

    2013-01-01

    This study aimed to evaluate the behaviour of two horizontal subsurface flow constructed wetland units regarding solids build up and clogging of the filter medium. In order to analyse the causes of this process, which is considered the major operational problem of constructed wetlands, studies were carried out to characterize accumulated solids and hydraulic conductivity at specific points of the beds of two wetlands (planted with Typha latifolia and unplanted units) receiving effluent from an upflow anaerobic sludge blanket reactor treating sanitary sewage (population equivalent of 50 inhabitants each unit). The experiments were performed after the units were operating for 2 years and 4 months. This study presents comparative results related to the quantification and characterization of accumulated solids and hydraulic conductivity along the length and width of the filter beds. Approximately 80% of the solids found were inorganic (fixed). Near the inlet end, the rate interstitial solids/attached solids was 5.0, while in the outlet end it was reduced to 1.5. Hydraulic conductivity was lower near the inlet of the units (as expected) and, by comparing the planted wetland with the unplanted, the hydraulic conductivity was lower in the former, resulting in larger undesired surface flow.

  10. Integrating hydraulic conductivity with biogeochemical gradients and microbial activity along river-groundwater exchange zones in a subtropical stream

    Science.gov (United States)

    Claret, Cécile; Boulton, Andrew J.

    2009-02-01

    The pervious lateral bars (parafluvial zone) and beds (hyporheic zone), where stream water and groundwater exchange, are dynamic sites of hydrological and biological retention. The significance of these biogeochemical ‘hotspots’ to stream and groundwater metabolism is largely controlled by filtration capacity, defined as the extent to which subsurface flowpaths and matrix hydraulic conductivity modify water characteristics. Where hydraulic conductivity is high, gradients in biogeochemistry and microbial activity along subsurface flowpaths were hypothesized to be less marked than where hydraulic conductivity is low. This hypothesis was tested in two riffles and gravel bars in an Australian subtropical stream. At one site, gradients in chemical and microbial variables along flowpaths were associated with reduced hydraulic conductivity, longer water residence time and reduced filtration capacity compared with the second site where filtration capacity was greater and longitudinal biogeochemical trends were dampened. These results imply that factors affecting the sediment matrix in this subtropical stream can alter filtration capacity, interstitial microbial activity and biogeochemical gradients along subsurface flowpaths. This hydroecological approach also indicates potential for a simple field technique to estimate filtration capacity and predict the prevailing hyporheic gradients in microbial activity and biogeochemical processing efficiency, with significant implications for stream ecosystem function.

  11. Root hydraulic conductivity and xylem sap levels of zeatin riboside and abscisic acid in ectomycorrhizal Douglas fir seedlings

    Science.gov (United States)

    Mark D. Coleman; Caroline S. Bledsoe; Barbara A. Smit

    1990-01-01

    Mechanistic hypotheses to explain mycorrhizal enhancement of root hydraulic conductivity (Lp) suggest that phosphorus (P) nutrition, plant growth substances and/or altered morphology may be responsible. Such ideas are based on work with VA (vesicular-arbuscular) mycorrhizas. Since VA mycorrhizas and ectomycorrhizas differ in many respects, they...

  12. Do quantitative vessel and pit characters account for ion-mediated changes in the hydraulic conductance of angiosperm xylem?

    NARCIS (Netherlands)

    Jansen, S.; Gortan, E.; Lens, F.; Assunta Lo Gullo, M.; Salleo, S.; Scholtz, A.; Stein, A.; Trifilò, P.; Nardini, A.

    2011-01-01

    • The hydraulic conductance of angiosperm xylem has been suggested to vary with changes in sap solute concentrations because of intervessel pit properties. • The magnitude of the ‘ionic effect’ was linked with vessel and pit dimensions in 20 angiosperm species covering 13 families including six Laur

  13. HYDRAULIC CONDUCTIVITY OF SALTSTONE FORMULATED USING 1Q11, 2Q11 AND 3Q11 TANK 50 SLURRY SAMPLES

    Energy Technology Data Exchange (ETDEWEB)

    Reigel, M.; Nichols, R.

    2012-06-27

    As part of the Saltstone formulation work requested by Waste Solidification Engineering (WSE), Savannah River National Laboratory (SRNL) was tasked with preparing Saltstone samples for fresh property analysis and hydraulic conductivity measurements using actual Tank 50 salt solution rather than simulated salt solution. Samples of low level waste salt solution collected from Tank 50H during the first, second, and third quarters of 2011 were used to formulate the Saltstone samples. The salt solution was mixed with premix (45 wt % slag, 45 wt % fly ash, and 10 wt % cement), in a ratio consistent with facility operating conditions during the quarter of interest. The fresh properties (gel, set, bleed) of each mix were evaluated and compared to the recommended acceptance criteria for the Saltstone Production Facility. ASTM D5084-03, Method C was used to measure the hydraulic conductivity of the Saltstone samples. The hydraulic conductivity of Saltstone samples prepared from 1Q11 and 2Q11 samples of Tank 50H is 4.2E-9 cm/sec and 2.6E-9 cm/sec, respectively. Two additional 2Q11 and one 3Q11 sample were not successfully tested due to the inability to achieve stable readings during saturation and testing. The hydraulic conductivity of the samples made from Tank 50H salt solution compare well to samples prepared with simulated salt solution and cured under similar conditions (1.4E-9 - 4.9E-8 cm/sec).

  14. Using automatic calibration method for optimizing the performance of Pedotransfer functions of saturated hydraulic conductivity

    Directory of Open Access Journals (Sweden)

    Ahmed M. Abdelbaki

    2016-06-01

    Full Text Available Pedotransfer functions (PTFs are an easy way to predict saturated hydraulic conductivity (Ksat without measurements. This study aims to auto calibrate 22 PTFs. The PTFs were divided into three groups according to its input requirements and the shuffled complex evolution algorithm was used in calibration. The results showed great modification in the performance of the functions compared to the original published functions. For group 1 PTFs, the geometric mean error ratio (GMER and the geometric standard deviation of error ratio (GSDER values were modified from range (1.27–6.09, (5.2–7.01 to (0.91–1.15, (4.88–5.85 respectively. For group 2 PTFs, the GMER and the GSDER values were modified from (0.3–1.55, (5.9–12.38 to (1.00–1.03, (5.5–5.9 respectively. For group 3 PTFs, the GMER and the GSDER values were modified from (0.11–2.06, (5.55–16.42 to (0.82–1.01, (5.1–6.17 respectively. The result showed that the automatic calibration is an efficient and accurate method to enhance the performance of the PTFs.

  15. Effect of pH on saturated hydraulic conductivity and soil dispersion

    Energy Technology Data Exchange (ETDEWEB)

    Suarez, D.L.; Roades, J.D.; Lavado, R.; Grieve, C.M.

    The adverse effects of exchangeable sodium on soil hydraulic conductivity (K) are well known, but at present only sodicity and total electrolyte concentration are used in evaluating irrigation water suitability. In arid areas, high sodicity is often associatd with high dissolved carbonate and thus high pH, but in humid areas high sodicity may be associated with low pH. To evaluate the effect of pH (as an independent variable) on K, solutions with the same SAR and electrolyte level were prepared at pH 6, 7, 8, and 9. Saturated K values were determined at constant flux in columns packed at a bulk density of 1.5 Mg m/sup -3/. At pH 9, saturated K values were lower than at pH 6 for a montmorillonitic and kaolinitic soil. For a vermiculitic soil with lower organic carbon and higher silt content, pH changes did not cause large K differences. Decreases in K were not reversible on application of waters with higher electrolyte levels. The results from the K experiments were generally consistent with optical transmission measurements of dispersion. Although anion adsorption was at or below detection limits and cation exchange capacity (CEC) was only slightly dependent on pH, differences in pH effects on K among soils are likely due to differences in quantities of variable-charge minerals and organic matter.

  16. Arbuscular mycorrhizal symbiosis and methyl jasmonate avoid the inhibition of root hydraulic conductivity caused by drought.

    Science.gov (United States)

    Sánchez-Romera, Beatriz; Ruiz-Lozano, Juan Manuel; Zamarreño, Ángel María; García-Mina, José María; Aroca, Ricardo

    2016-02-01

    Hormonal regulation and symbiotic relationships provide benefits for plants to overcome stress conditions. The aim of this study was to elucidate the effects of exogenous methyl jasmonate (MeJA) application on root hydraulic conductivity (L) of Phaseolus vulgaris plants which established arbuscular mycorrhizal (AM) symbiosis under two water regimes (well-watered and drought conditions). The variation in endogenous contents of several hormones (MeJA, JA, abscisic acid (ABA), indol-3-acetic acid (IAA), salicylic acid (SA)) and the changes in aquaporin gene expression, protein abundance and phosphorylation state were analyzed. AM symbiosis decreased L under well-watered conditions, which was partially reverted by the MeJA treatment, apparently by a drop in root IAA contents. Also, AM symbiosis and MeJA prevented inhibition of L under drought conditions, most probably by a reduction in root SA contents. Additionally, the gene expression of two fungal aquaporins was upregulated under drought conditions, independently of the MeJA treatment. Plant aquaporin gene expression could not explain the behaviour of L. Conversely, evidence was found for the control of L by phosphorylation of aquaporins. Hence, MeJA addition modified the response of L to both AM symbiosis and drought, presumably by regulating the root contents of IAA and SA and the phosphorylation state of aquaporins.

  17. Spectral induced polarization measurements for predicting the hydraulic conductivity in sandy aquifers

    Directory of Open Access Journals (Sweden)

    M. Attwa

    2013-10-01

    Full Text Available Field and laboratory spectral induced polarization (SIP measurements are integrated to characterize the hydrogeological conditions at the Schillerslage test site in Germany. The phase images are capable of monitoring thin peat layers within the sandy aquifers. However, the field results show limitations of decreasing resolution with depth. In comparison with the field inversion results, the SIP laboratory measurements show a certain shift in SIP response due to different compaction and sorting of the samples. The SIP data are analyzed to derive an empirical relationship for predicting the hydraulic conductivity (K. In particular, two significant but weak correlations between individual real resistivities (ρ' and relaxation times (τ, based on a Debye decomposition (DD model, with measured K are found for the upper groundwater aquifer. The maximum relaxation time (τmax and logarithmically weighted average relaxation time (τlw show a better relation with K values than the median value τ50. A combined power law relation between individual ρ' and τ with K is developed with an expression of A · (ρ'B · (τlwC, where A, B and C are determined using a least-squares fit between the measured and predicted K. The suggested approach with the calculated coefficients of the first aquifer is applied for the second. Results show good correlation with the measured K indicating that the derived relationship is superior to single phase angle models as Börner or Slater models.

  18. Reassessing the MADE direct-push hydraulic conductivity data using a revised calibration procedure

    Science.gov (United States)

    Bohling, Geoffrey C.; Liu, Gaisheng; Dietrich, Peter; Butler, James J.

    2016-11-01

    In earlier work, we presented a geostatistical assessment of high-resolution hydraulic conductivity (K) profiles obtained at the MADE site using direct-push (DP) methods. The profiles are derived from direct-push injection logger (DPIL) measurements that provide a relative indicator of vertical variations in K with a sample spacing of 1.5 cm. The DPIL profiles are converted to K profiles by calibrating to the results of direct-push permeameter (DPP) tests performed at selected depths in some of the profiles. Our original calibration used a linear transform that failed to adequately account for an upper limit on DPIL responses in high-K zones and noise in the DPIL data. Here we present a revised calibration procedure that accounts for the upper limit and noise, leading to DPIL K values that display a somewhat different univariate distribution and a lower lnK variance (5.9 ± 1.5) than the original calibration values (6.9 ± 1.8), although each variance estimate falls within the other's 95% confidence interval. Despite the change in the univariate distribution, the autocorrelation structure and large-scale patterns exhibited by the revised DPIL K values still agree well with those exhibited by the flowmeter data from the site. We provide the DPIL and DPP data, along with our calibrated DPIL K values, in the Supporting Information.

  19. Estimation of soil saturated hydraulic conductivity by artificial neural networks ensemble in smectitic soils

    Science.gov (United States)

    Sedaghat, A.; Bayat, H.; Safari Sinegani, A. A.

    2016-03-01

    The saturated hydraulic conductivity ( K s ) of the soil is one of the main soil physical properties. Indirect estimation of this parameter using pedo-transfer functions (PTFs) has received considerable attention. The Purpose of this study was to improve the estimation of K s using fractal parameters of particle and micro-aggregate size distributions in smectitic soils. In this study 260 disturbed and undisturbed soil samples were collected from Guilan province, the north of Iran. The fractal model of Bird and Perrier was used to compute the fractal parameters of particle and micro-aggregate size distributions. The PTFs were developed by artificial neural networks (ANNs) ensemble to estimate K s by using available soil data and fractal parameters. There were found significant correlations between K s and fractal parameters of particles and microaggregates. Estimation of K s was improved significantly by using fractal parameters of soil micro-aggregates as predictors. But using geometric mean and geometric standard deviation of particles diameter did not improve K s estimations significantly. Using fractal parameters of particles and micro-aggregates simultaneously, had the most effect in the estimation of K s . Generally, fractal parameters can be successfully used as input parameters to improve the estimation of K s in the PTFs in smectitic soils. As a result, ANNs ensemble successfully correlated the fractal parameters of particles and micro-aggregates to K s .

  20. Rapid measurement of field-saturated hydraulic conductivity for areal characterization

    Science.gov (United States)

    Nimmo, J.R.; Schmidt, K.M.; Perkins, K.S.; Stock, J.D.

    2009-01-01

    To provide an improved methodology for characterizing the field-saturated hydraulic conductivity (Kfs) over broad areas with extreme spatial variability and ordinary limitations of time and resources, we developed and tested a simplified apparatus and procedure, correcting mathematically for the major deficiencies of the simplified implementation. The methodology includes use of a portable, falling-head, small-diameter (???20 cm) single-ring infiltrometer and an analytical formula for Kfs that compensates both for nonconstant falling head and for the subsurface radial spreading that unavoidably occurs with small ring size. We applied this method to alluvial fan deposits varying in degree of pedogenic maturity in the arid Mojave National Preserve, California. The measurements are consistent with a more rigorous and time-consuming Kfs measurement method, produce the expected systematic trends in Kfs when compared among soils of contrasting degrees of pedogenic development, and relate in expected ways to results of widely accepted methods. ?? Soil Science Society of America. All rights reserved.

  1. Integration of Fuzzy and Probabilistic Information in the Description of Hydraulic Conductivity

    Science.gov (United States)

    Druschel, B.; Ozbek, M.; Pinder, G.

    2004-12-01

    Evaluation of the heterogeneity of hydraulic conductivity, K, is a well-known problem in groundwater hydrology. The open question is how to fully represent a given highly heterogeneous K field and its inherent uncertainty at least cost. Today, most K fields are analyzed using field test data and probability theory. Uncertainty is usually reported in the spatial covariance. In an attempt to develop a more cost effective method which still provides an accurate approximation of a K field, we propose using an evidence theory framework to merge probabilistic and fuzzy (or possibilistic) information in an effort to improve our ability to fully define a K field. The tool chosen to fuse probabilistic information obtained via experiment and subjective information provided by the groundwater professional is Dempster's Rule of Combination. In using this theory we must create mass assignments for our subject of interest, describing the degree of evidence that supports the presence of our subject in a particular set. These mass assignments can be created directly from the probabilistic information and, in the case of the subjective information, from feedback we obtain from an expert. The fusion of these two types of information provides a better description of uncertainty than would typically be available with just probability theory alone.

  2. Spatial Variability of Soil Saturated Hydraulic Conductivity in a Small Watershed of Loess Hilly Region,China

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Saturated hydraulic conductivity (Ks) is an important soil hydraulic parameter for charactering the rate of water flow across the soils and is mainly related to its high spatial variability. In a small watershed with the area of 0.27 km2 in the Loess Plateau, Ks of 197 soil samples under different vegetations and landforms were measured. Ks had a moderate variability for total samples. The forestland had high Ks with low coefficient of variation (CV), but the grassland in the watershed bottom had low Ks wit...

  3. Reflection seismic imaging of a hydraulically conductive fracture zone in a high noise area, Forsmark, Sweden

    Science.gov (United States)

    Juhlin, C.; Stephens, M. B.; Cosma, C.

    2007-05-01

    borehole shows that the reflection corresponds to a hydraulically conductive fracture zone that was intersected at about 320 m depth.

  4. Comparison of instream methods for measuring hydraulic conductivity in sandy streambeds.

    Science.gov (United States)

    Landon, M K; Rus, D L; Harvey, F E

    2001-01-01

    Streambed hydraulic conductivity (K) values were determined at seven stream transects in the Platte River Basin in Nebraska using different instream measurement techniques. Values were compared to determine the most appropriate technique(s) for use in sandy streambeds. Values of K determined from field falling- and constant-head permeameter tests analyzed using the Darcy equation decreased as permeameter diameter increased. Seepage meters coupled with hydraulic gradient measurements failed to yield K values in 40% of the trials. Consequently, Darcy permeameter and seepage meter tests were not preferred approaches. In the upper 0.25 m of the streambed, field falling- and constant-head permeameter tests analyzed with the Hvorslev solution generally had similar K values that were significantly greater than those determined using the Hazen grain-size, Bouwer and Rice slug test for anisotropic and isotropic conditions, and Alyamani and Sen grain-size methods; median differences between these tests and the Hvorslev falling-head 60 cm diameter permeameter were about 8, 9, 17, and 35 m/day, respectively. The Hvorslev falling-head permeameter test is considered the most robust method for measuring K of the upper 0.25 m of the streambed because of the inherent limitations of the empirical grain-size methods and less sediment disturbance for permeameter than slug tests. However, lateral variability in K along transects on the Platte, North Platte, and Wood Rivers was greater than variability in K between valid permeameter, grain-size, or slug tests, indicating that the method used may matter less than making enough measurements to characterize spatial variability adequately. At the Platte River tributary sites, the upper 0.3 m of the streambed typically had greater K than sediment located 0.3 to 2.5 m below the streambed surface, indicating that deposits below the streambed may limit ground water/surface water fluxes. The Hvorslev permeameter tests are not a practical

  5. Characterization of a rice variety with high hydraulic conductance and identification of the chromosome region responsible using chromosome segment substitution lines.

    Science.gov (United States)

    Adachi, Shunsuke; Tsuru, Yukiko; Kondo, Motohiko; Yamamoto, Toshio; Arai-Sanoh, Yumiko; Ando, Tsuyu; Ookawa, Taiichiro; Yano, Masahiro; Hirasawa, Tadashi

    2010-11-01

    The rate of photosynthesis in paddy rice often decreases at noon on sunny days because of water stress, even under submerged conditions. Maintenance of higher rates of photosynthesis during the day might improve both yield and dry matter production in paddy rice. A high-yielding indica variety, 'Habataki', maintains a high rate of leaf photosynthesis during the daytime because of the higher hydraulic conductance from roots to leaves than in the standard japonica variety 'Sasanishiki'. This research was conducted to characterize the trait responsible for the higher hydraulic conductance in 'Habataki' and identified a chromosome region for the high hydraulic conductance. Hydraulic conductance to passive water transport and to osmotic water transport was determined for plants under intense transpiration and for plants without transpiration, respectively. The varietal difference in hydraulic conductance was examined with respect to root surface area and hydraulic conductivity (hydraulic conductance per root surface area, L(p)). To identify the chromosome region responsible for higher hydraulic conductance, chromosome segment substitution lines (CSSLs) derived from a cross between 'Sasanishiki' and 'Habataki' were used. The significantly higher hydraulic conductance resulted from the larger root surface area not from L(p) in 'Habataki'. A chromosome region associated with the elevated hydraulic conductance was detected between RM3916 and RM2431 on the long arm of chromosome 4. The CSSL, in which this region was substituted with the 'Habataki' chromosome segment in the 'Sasanishiki' background, had a larger root mass than 'Sasanishiki'. The trait for increasing plant hydraulic conductance and, therefore, maintaining the higher rate of leaf photosynthesis under the conditions of intense transpiration in 'Habataki' was identified, and it was estimated that there is at least one chromosome region for the trait located on chromosome 4.

  6. The contribution of vascular and extra-vascular water pathways to drought-induced decline of leaf hydraulic conductance.

    Science.gov (United States)

    Trifiló, Patrizia; Raimondo, Fabio; Savi, Tadeja; Lo Gullo, Maria A; Nardini, Andrea

    2016-09-01

    Drought stress can impair leaf hydraulic conductance (Kleaf), but the relative contribution of changes in the efficiency of the vein xylem water pathway and in the mesophyll route outside the xylem in driving the decline of Kleaf is still debated. We report direct measurements of dehydration-induced changes in the hydraulic resistance (R=1/K) of whole leaf (Rleaf), as well as of the leaf xylem (Rx) and extra-vascular pathways (Rox) in four Angiosperm species. Rleaf, Rx, and Rox were measured using the vacuum chamber method (VCM). Rleaf values during progressive leaf dehydration were also validated with measurements performed using the rehydration kinetic method (RKM). We analysed correlations between changes in Rx or Rox and Rleaf, as well as between morpho-anatomical traits (including dehydration-induced leaf shrinkage), vulnerability to embolism, and leaf water relation parameters. Measurements revealed that the relative contribution of vascular and extra-vascular hydraulic properties in driving Kleaf decline during dehydration is species-specific. Whilst in two study species the progressive impairment of both vascular and extra-vascular pathways contributed to leaf hydraulic vulnerability, in the other two species the vascular pathway remained substantially unaltered during leaf dehydration, and Kleaf decline was apparently caused only by changes in the hydraulic properties of the extra-vascular compartment.

  7. The role of water channel proteins in facilitating recovery of leaf hydraulic conductance from water stress in Populus trichocarpa.

    Directory of Open Access Journals (Sweden)

    Joan Laur

    Full Text Available Gas exchange is constrained by the whole-plant hydraulic conductance (Kplant. Leaves account for an important fraction of Kplant and may therefore represent a major determinant of plant productivity. Leaf hydraulic conductance (Kleaf decreases with increasing water stress, which is due to xylem embolism in leaf veins and/or the properties of the extra-xylary pathway. Water flow through living tissues is facilitated and regulated by water channel proteins called aquaporins (AQPs. Here we assessed changes in the hydraulic conductance of Populus trichocarpa leaves during a dehydration-rewatering episode. While leaves were highly sensitive to drought, Kleaf recovered only 2 hours after plants were rewatered. Recovery of Kleaf was absent when excised leaves were bench-dried and subsequently xylem-perfused with a solution containing AQP inhibitors. We examined the expression patterns of 12 highly expressed AQP genes during a dehydration-rehydration episode to identify isoforms that may be involved in leaf hydraulic adjustments. Among the AQPs tested, several genes encoding tonoplast intrinsic proteins (TIPs showed large increases in expression in rehydrated leaves, suggesting that TIPs contribute to reversing drought-induced reductions in Kleaf. TIPs were localized in xylem parenchyma, consistent with a role in facilitating water exchange between xylem vessels and adjacent living cells. Dye uptake experiments suggested that reversible embolism formation in minor leaf veins contributed to the observed changes in Kleaf.

  8. Changes in root hydraulic conductivity facilitate the overall hydraulic response of rice (Oryza sativa L.) cultivars to salt and osmotic stress.

    Science.gov (United States)

    Meng, Delong; Fricke, Wieland

    2017-04-01

    The aim of the present work was to assess the significance of changes in root AQP gene expression and hydraulic conductivity (Lp) in the regulation of water balance in two hydroponically-grown rice cultivars (Azucena, Bala) which differ in root morphology, stomatal regulation and aquaporin (AQP) isoform expression. Plants were exposed to NaCl (25 mM, 50 mM) and osmotic stress (5%, 10% PEG6000). Root Lp was determined for exuding root systems (osmotic forces driving water uptake; 'exudation Lp') and transpiring plants (hydrostatic forces dominating; 'transpiration-Lp'). Gene expression was analysed by qPCR. Stress treatments caused a consistent and significant decrease in plant growth, transpirational water loss, stomatal conductance, shoot-to-root surface area ratio and root Lp. Comparison of exudation-with transpiration-Lp supported a significant contribution of AQP-facilitated water flow to root water uptake. Changes in root Lp in response to treatments were correlated much stronger with root morphological characteristics, such as the number of main and lateral roots, surface area ratio of root to shoot and plant transpiration rate than with AQP gene expression. Changes in root Lp, involving AQP function, form an integral part of the plant hydraulic response to stress and facilitate changes in the root-to-shoot surface area ratio, transpiration and stomatal conductance.

  9. Geologic Controls of Hydraulic Conductivity in the Snake River Plain Aquifer At and Near the Idaho National Engineering and Environmental Laboratory, Idaho

    Energy Technology Data Exchange (ETDEWEB)

    S. R. Anderson; M. A. Kuntz; L. C. Davis

    1999-02-01

    The effective hydraulic conductivity of basalt and interbedded sediment that compose the Snake River Plain aquifer at and near the Idaho National Engineering and Environmental Laboratory (INEEL) ranges from about 1.0x10 -2 to 3.2x10 4 feet per day (ft/d). This six-order-of-magnitude range of hydraulic conductivity was estimated from single-well aquifer tests in 114 wells, and is attributed mainly to the physical characteristics and distribution of basalt flows and dikes. Hydraulic conductivity is greatest in thin pahoehoe flows and near-vent volcanic deposits. Hydraulic conductivity is least in flows and deposits cut by dikes. Estimates of hydraulic conductivity at and near the INEEL are similar to those measured in similar volcanic settings in Hawaii. The largest variety of rock types and the greatest range of hydraulic conductivity are in volcanic rift zones, which are characterized by numerous aligned volcanic vents and fissures related to underlying dikes. Three broad categories of hydraulic conductivity corresponding to six general types of geologic controls can be inferred from the distribution of wells and vent corridors. Hydraulic conductivity of basalt flows probably is increased by localized fissures and coarse mixtures of interbedded sediment, scoria, and basalt rubble. Hydraulic conductivity of basalt flows is decreased locally by abundant alteration minerals of probable hydrothermal origin. Hydraulic conductivity varies as much as six orders of magnitude in a single vent corridor and varies from three to five orders of magnitude within distances of 500 to 1,000 feet. Abrupt changes in hydraulic conductivity over short distances suggest the presence of preferential pathways and local barriers that may greatly affect the movement of ground water and the dispersion of radioactive and chemical wastes downgradient from points of waste disposal.

  10. Influence of leaf vein density and thickness on hydraulic conductance and photosynthesis in rice (Oryza sativa L.) during water stress

    OpenAIRE

    2016-01-01

    The leaf venation architecture is an ideal, highly structured and efficient irrigation system in plant leaves. Leaf vein density (LVD) and vein thickness are the two major properties of this system. Leaf laminae carry out photosynthesis to harvest the maximum biological yield. It is still unknown whether the LVD and/or leaf vein thickness determines the plant hydraulic conductance (K plant) and leaf photosynthetic rate (A). To investigate this topic, the current study was conducted with two v...

  11. Improved thermally conducting electron transfer polymers

    Science.gov (United States)

    Jenkins, R. K.; Byrd, N. R.; Lister, J. L.

    1972-01-01

    Development of polymers with improved heat transfer coefficients for use in encapsulating electronic modules is discussed. Chemical reactions for synthesizing the polymers are described and thermodynamic and physical properties are analyzed.

  12. INFLUENCE OF CYCLIC FREEZING AND THAWING ON THE HYDRAULIC CONDUCTIVITY OF SELECTED AGGREGATES USED IN THE CONSTRUCTION OF GREEN ROOFS

    Directory of Open Access Journals (Sweden)

    Karolina Gwóżdź

    2016-09-01

    Full Text Available The construction of a green roof requires drainage which ought to be characterized by adequate hydraulic conductivity and be resistant to changing meteorological conditions during the winter period. A properly functioning drainage system guarantees the reliability of the entire green roof system. The article presents studies on the freeze-thaw durability and hydraulic conductivity of selected aggregates applied for constructing green roof drainage systems. The aggregates were subjected to a cyclic freezing and thawing process in 30 and 70 cycles. The obtained results indicate that the conductivity of aggregates studied using the constant head method decreases along with an increase in the number of freeze-thaw cycles they were subjected to. This means that the indicator of freeze-thaw durability can have an indicative nature in the assessment of the usefulness of selected aggregates for constructing drainage layers. The conducted studies indicate that the deciding parameter when selecting an aggregate ought to be its hydraulic conductivity, determined accounting for the changes taking place in the freeze-thaw cycles. The equations of changes in the conductivity of aggregates indicated by the authors make it possible to assess them for practical purposes.

  13. Hydraulic Conductivity Functions in Relation to Some Chemical Properties in a Cultivated Oxisols of a Humid Region, Delta State, Nigeria

    Directory of Open Access Journals (Sweden)

    Egbuchua, C. N.

    2014-04-01

    Full Text Available The study was conducted to evaluate hydraulic conductivity functions in relation to some soil chemical properties in an oxisols of the tropics. Field and laboratory studies were carried out and data collected, subjected to statistical analytical procedure for computing coefficient of variability and correlation among soil properties. Results of the study showed that hydraulic conductivity functions varied spatially and temporarily across the experimental points with a moderate mean value of 0.0026 cm/h and a coefficient o variation of 31.45% soil chemical properties showed that the soils were acidic with a mean pH value of 5.12. Organic carbon, total nitrogen and available phosphorus were low with mean values of 1.29%, 0.68% and 4.43 mgkg-1. Coefficient of variability among soil properties indicated less to moderately variable. Soil pH had negative correlation with all the soil properties evaluated.

  14. Electronic Tongue Containing Redox and Conductivity Sensors

    Science.gov (United States)

    Buehler, Martin

    2007-01-01

    The Electronic Tongue (E-tongue 2) is an assembly of sensors for measuring concentrations of metal ions and possibly other contaminants in water. Potential uses for electronic tongues include monitoring the chemical quality of water in a variety of natural, industrial, and laboratory settings, and detecting micro-organisms indirectly by measuring microbially influenced corrosion. The device includes a heater, a temperature sensor, an oxidation/reduction (redox) sensor pair, an electrical sensor, an array of eight galvanic cells, and eight ion-specific electrodes.

  15. Towards improved estimation of the unsaturated soil hydraulic conductivity in the near saturated range by a fully automated, pressure controlled unit gradient experiment.

    Science.gov (United States)

    Werisch, Stefan; Müller, Marius

    2017-04-01

    Determination of soil hydraulic properties has always been an important part of soil physical research and model applications. While several experiments are available to measure the water retention of soil samples, the determination of the unsaturated hydraulic conductivity is often more complicated, bound to strong assumption and time consuming. Although, the application of unit gradient experiments is recommended since the middle of the last century, as one method towards a (assumption free) direct measurement of the unsaturated hydraulic conductivity, data from unit gradient experiments is seldom to never reported in literature. We developed and build a fully automated, pressure controlled, unit gradient experiment, which allows a precise determination of the unsaturated soil hydraulic conductivity K(h) and water retention VWC(h), especially in the highly dynamic near saturated range. The measurement apparatus applies the concept of hanging water columns and imposes the required soil water pressure by dual porous plates. This concepts allows the simultaneous and direct measurement of water retention and hydraulic conductivity. Moreover, this approach results in a technically less demanding experiment than related flux controlled experiments, and virtually any flux can be measured. Thus, both soil properties can be measured in mm resolution, for wetting and drying processes, between saturation and field capacity for all soil types. Our results show, that it is important to establish separate measurements of the unsaturated hydraulic conductivity in the near saturated range, as the shape of the retention function and hydraulic conductivity curve do not necessarily match. Consequently, the prediction of the hydraulic conductivity curve from measurements of the water retention behavior in combination with a value for the saturated hydraulic conductivity can be misleading. Thus, separate parameterizations of the individual functions might be necessary and are

  16. A tale of two plasticities: leaf hydraulic conductances and related traits diverge for two tropical epiphytes from contrasting light environments.

    Science.gov (United States)

    North, Gretchen B; Browne, Marvin G; Fukui, Kyle; Maharaj, Franklin D R; Phillips, Carly A; Woodside, Walter T

    2016-07-01

    We compared the effects of different light environments on leaf hydraulic conductance (Kleaf ) for two congeneric epiphytes, the tank bromeliads Guzmania lingulata (L.) Mez and Guzmania monostachia (L.) Rusby ex Mez. They occur sympatrically at the study site, although G. monostachia is both wider ranging and typically found in higher light. We collected plants from two levels of irradiance and measured Kleaf as well as related morphological and anatomical traits. Leaf xylem conductance (Kxy ) was estimated from tracheid dimensions, and leaf conductance outside the xylem (Kox ) was derived from a leaky cable model. For G. monostachia, but not for G. lingulata, Kleaf and Kxy were significantly higher in high light conditions. Under both light conditions, Kxy and Kox were co-limiting for the two species, and all conductances were in the low range for angiosperms. With respect to hydraulic conductances and a number of related anatomical traits, G. monostachia exhibited greater plasticity than did G. lingulata, which responded to high light chiefly by reducing leaf size. The positive plasticity of leaf hydraulic traits in varying light environments in G. monostachia contrasted with negative plasticity in leaf size for G. lingulata, suggesting that G. monostachia may be better able to respond to forest conditions that are likely to be warmer and more disturbed in the future.

  17. Method of Relating Grain Size Distribution to Hydraulic Conductivity in Dune Sands to Assist in Assessing Managed Aquifer Recharge Projects: Wadi Khulays Dune Field, Western Saudi Arabia

    KAUST Repository

    Lopez Valencia, Oliver M.

    2015-11-12

    Planning for use of a dune field aquifer for managed aquifer recharge (MAR) requires that hydraulic properties need to be estimated over a large geographic area. Saturated hydraulic conductivity of dune sands is commonly estimated from grain size distribution data by employing some type of empirical equation. Over 50 samples from the Wadi Khulays dune field in Western Saudi Arabia were collected and the grain size distribution, porosity, and hydraulic conductivity were measured. An evaluation of 20 existing empirical equations showed a generally high degree of error in the predicted compared to the measured hydraulic conductivity values of these samples. Statistical analyses comparing estimated versus measured hydraulic conductivity demonstrated that there is a significant relationship between hydraulic conductivity and mud percentage (and skewness). The modified Beyer equation, which showed a generally low prediction error, was modified by adding a second term fitting parameter related to the mud concentration based on 25 of the 50 samples analyzed. An inverse optimization process was conducted to quantify the fitting parameter and a new empirical equation was developed. This equation was tested against the remaining 25 samples analyzed and produced an estimated saturated hydraulic conductivity with the lowest error of any empirical equation. This methodology can be used for large dune field hydraulic conductivity estimation and reduce planning costs for MAR systems.

  18. Method of Relating Grain Size Distribution to Hydraulic Conductivity in Dune Sands to Assist in Assessing Managed Aquifer Recharge Projects: Wadi Khulays Dune Field, Western Saudi Arabia

    Directory of Open Access Journals (Sweden)

    Oliver M. Lopez

    2015-11-01

    Full Text Available Planning for use of a dune field aquifer for managed aquifer recharge (MAR requires that hydraulic properties need to be estimated over a large geographic area. Saturated hydraulic conductivity of dune sands is commonly estimated from grain size distribution data by employing some type of empirical equation. Over 50 samples from the Wadi Khulays dune field in Western Saudi Arabia were collected and the grain size distribution, porosity, and hydraulic conductivity were measured. An evaluation of 20 existing empirical equations showed a generally high degree of error in the predicted compared to the measured hydraulic conductivity values of these samples. Statistical analyses comparing estimated versus measured hydraulic conductivity demonstrated that there is a significant relationship between hydraulic conductivity and mud percentage (and skewness. The modified Beyer equation, which showed a generally low prediction error, was modified by adding a second term fitting parameter related to the mud concentration based on 25 of the 50 samples analyzed. An inverse optimization process was conducted to quantify the fitting parameter and a new empirical equation was developed. This equation was tested against the remaining 25 samples analyzed and produced an estimated saturated hydraulic conductivity with the lowest error of any empirical equation. This methodology can be used for large dune field hydraulic conductivity estimation and reduce planning costs for MAR systems.

  19. Spectral induced polarization measurements for environmental purposes and predicting the hydraulic conductivity in sandy aquifers

    Directory of Open Access Journals (Sweden)

    M. Attwa

    2013-04-01

    Full Text Available Low-frequency field and laboratory induced polarization measurements are carried out to characterize the hydrogeological conditions at Schillerslage test site in Germany. The laboratory spectral induced polarization (SIP data are analyzed to derive an empirical relationship for predicting the hydraulic conductivity (K in the field scale. On the other hand, the results from SIP sounding and profiling field data indicate that the method identifies the lithological layers with sufficient resolution to achieve our objectives. Two main Quaternary groundwater aquifers separated by a till layer can be well differentiated. Furthermore, the phase images are also capable of monitoring thin peat layers within the sandy groundwater aquifer. However, the field results show limitations of decreasing resolution with depth and/or low data coverage. Similarly, the SIP laboratory results show a certain shift in SIP response due to different compaction and sorting of the samples. The overall results obtained show that the integration of field and laboratory SIP measurements is an efficient tool to avoid a hydrogeological misinterpretation. In particular, two significant but weak correlations between individual real resistivities (ρ' and relaxation times (τ, based on a Debye decomposition (DD model, with measured K are found for the upper groundwater aquifer. While the maximum relaxation time (τmax and logarithmically weighted average relaxation time (τlw show a better relation with K values than the median value τ50, however, the single relationships are weak. A combined power law relation between individual ρ' and/or τ with K is developed with an expression of A · (ρ'B · (τlwC, where A, B and C are determined using a least-squares fit between the measured and predicted K. The suggested approach with the calculated coefficients of the first aquifer is applied for the second one. The results indicate a good correlation with the measured K and prove to be

  20. Ozone and simulated acid rain effects on growth root hydraulic conductivity, and photosynthesis of red spruce

    Energy Technology Data Exchange (ETDEWEB)

    Lee, W.S.; Chevone, B.I.; Seiler, J.R.

    1987-04-01

    Three-year-old red spruce seedlings were exposed to ozone (O/sub 3/) at 0.00 (control) or 0.10 ppm, 4 hr/d, 3 d/wk in combination with simulated rain (pH 3.0 or 5.6, 1 hr/d, 2 d/wk at 0.75 cm/hr) for 10 wks. All seedlings were submitted to two drought cycles after the 10-wk-treatment. O/sub 3/ significantly decreased root hydraulic conductivity (Lp) by 21% after 10 wks across all rain pHs. The reduction of Lp in seedlings treated with O/sub 3/ was enhanced by drought stress. Rain pH alone did not affect Lp during the 10-wks-exposure and drought cycles. However, the O/sub 3/ effect on Lp was more severe at pH 5.6 than at pH 3.0. Rain at pH 3.0 stimulated shoot height growth by 31% compared with pH 5.6 across all O/sub 3/ treatments. However, root, shoot, and total dry weight of seedlings were not changed by any treatments. Neither O/sub 3/ nor rain pH affected net photosynthetic (P/sub i/) response to branch water potential in plants subjected to one or two drought cycles. However, P/sub i/ was less sensitive to water potential after two drought cycles, indicating physiological adjustment to drought stress.

  1. Effect of urban waste compost application on soil near-saturated hydraulic conductivity.

    Science.gov (United States)

    Schneider, S; Coquet, Y; Vachier, P; Labat, C; Roger-Estrade, J; Benoit, P; Pot, V; Houot, S

    2009-01-01

    Compost application tends to increase soil fertility and is likely to modify soil hydrodynamic properties by acting on soil structural porosity. Two composts, a municipal solid waste compost (MSW) and a co-compost of green wastes and sewage sludge (SGW), have been applied every other year for 6 yr to cultivated plots located on a silt loam soil in the Parisian Basin, France. Four soil zones were defined in the topsoil after plowing: the plowpan located at the base of the plowed layer, compacted (Delta) or noncompacted (Gamma) zones located within the plowed layer, and interfurrows created by plowing and containing a large quantity of crop residues together with the recently-applied compost. To assess the effect of compost application on the near-saturated soil hydraulic conductivity, infiltration rates were measured using a tension disc infiltrometer at three water pressure potentials -0.6, -0.2, and -0.05 kPa in the various zones of the soil profile. Compost addition decreased K((sat)) in the interfurrows after plowing by almost one order of magnitude with average values of 5.6 x 10(-5) m.s(-1) in the MSW plot and 4.1 x 10(-5) m.s(-1) in the SGW plot, against 2.2 x 10(-4) m.s(-1) in the control plot. This effect had disappeared 6 mo after plowing when the average K((sat)) in the control plot had decreased to 1.9 x 10(-5) m.s(-1) while that in the compost-amended plots remained stable.

  2. Simulating soil-water movement through loess-veneered landscapes using nonconsilient saturated hydraulic conductivity measurements

    Science.gov (United States)

    Williamson, Tanja N.; Lee, Brad D.; Schoeneberger, Philip J.; McCauley, W. M.; Indorante, Samuel J.; Owens, Phillip R.

    2014-01-01

    Soil Survey Geographic Database (SSURGO) data are available for the entire United States, so are incorporated in many regional and national models of hydrology and environmental management. However, SSURGO does not provide an understanding of spatial variability and only includes saturated hydraulic conductivity (Ksat) values estimated from particle size analysis (PSA). This study showed model sensitivity to the substitution of SSURGO data with locally described soil properties or alternate methods of measuring Ksat. Incorporation of these different soil data sets significantly changed the results of hydrologic modeling as a consequence of the amount of space available to store soil water and how this soil water is moved downslope. Locally described soil profiles indicated a difference in Ksat when measured in the field vs. being estimated from PSA. This, in turn, caused a difference in which soil layers were incorporated in the hydrologic simulations using TOPMODEL, ultimately affecting how soil water storage was simulated. Simulations of free-flowing soil water, the amount of water traveling through pores too large to retain water against gravity, were compared with field observations of water in wells at five slope positions along a catena. Comparison of the simulated data with the observed data showed that the ability to model the range of conditions observed in the field varied as a function of three soil data sets (SSURGO and local field descriptions using PSA-derived Ksat or field-measured Ksat) and that comparison of absolute values of soil water storage are not valid if different characterizations of soil properties are used.

  3. Effect of exchangeable Mg on saturated hydraulic conductivity, disaggregation and clay dispersion of disturbed soils

    Science.gov (United States)

    Zhang, X. C.; Norton, L. D.

    2002-03-01

    Different opinions exist regarding the specific effect of Mg on soil physical and chemical properties. We hypothesized that Mg 2+, compared with Ca 2+, reduces saturated hydraulic conductivity ( Ks) via promoting clay swelling, disaggregation, and clay dispersion. Two soils (mixed, mesic Typic Hapludalfs) in packed soil columns were leached with either Ca- or Mg-containing solutions at the successive concentrations of 250, 10, 2, 0.5, and 0 mM. Critical flocculation concentration (CFC) in either Ca or Mg systems was determined with flocculation series tests. Aggregate stability and mean weight diameter (MWD) were assessed by wet-sieving. The CFCs were higher in Mg than in Ca for both soils, indicating that Mg is more dispersive than Ca. The MWDs measured using 1-2 mm aggregates of both soils were significantly larger for Ca-soils than for Mg-soils ( P=0.05). The Ksr (normalized with initial Ks) started to decline at higher concentrations for Mg than for Ca, and the reduction was much greater in Mg than in Ca above 0.5 mM. The Ksr and percent transmittance (inversely related to turbidity) of leachate at a given eluted pore volume following 'steady state' were higher in Ca than in Mg for both soils ( P=0.1), indicating lower permeability and more clay dispersion with the Mg treatment. Swelling and disaggregation, which reduced large pores, appeared to be the dominant process causing the rapid initial decline of Ksr. Clay dispersion and subsequent pore plugging became progressively important when electrolyte concentration was reduced to below CFCs.

  4. Electron conductance in curved quantum structures

    DEFF Research Database (Denmark)

    Willatzen, Morten; Gravesen, Jens

    2010-01-01

    A differential-geometry analysis is employed to investigate the transmission of electrons through a curved quantum-wire structure. Although the problem is a three-dimensional spatial problem, the Schrodinger equation can be separated into three general coordinates. Hence, the proposed method...

  5. Anisotropic electronic conduction in stacked two-dimensional titanium carbide

    Science.gov (United States)

    Hu, Tao; Zhang, Hui; Wang, Jiemin; Li, Zhaojin; Hu, Minmin; Tan, Jun; Hou, Pengxiang; Li, Feng; Wang, Xiaohui

    2015-11-01

    Stacked two-dimensional titanium carbide is an emerging conductive material for electrochemical energy storage which requires an understanding of the intrinsic electronic conduction. Here we report the electronic conduction properties of stacked Ti3C2T2 (T = OH, O, F) with two distinct stacking sequences (Bernal and simple hexagonal). On the basis of first-principles calculations and energy band theory analysis, both stacking sequences give rise to metallic conduction with Ti 3d electrons contributing most to the conduction. The conduction is also significantly anisotropic due to the fact that the effective masses of carriers including electrons and holes are remarkably direction-dependent. Such an anisotropic electronic conduction is evidenced by the I-V curves of an individual Ti3C2T2 particulate, which demonstrates that the in-plane electrical conduction is at least one order of magnitude higher than that vertical to the basal plane.

  6. Quantum Ising model coupled with conducting electrons

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, Yasufumi; Yonemitsu, Kenji [Institute for Molecular Science, 38 Nishigo-Naka, Myodaiji, Okazaki 444-8585 (Japan); Graduate University for Advanced studies, 38 Nishigo-Naka, Myodaiji, Okazaki 444-8585 (Japan)

    2005-01-01

    The effect of photo-doping on the quantum paraelectric SrTiO{sub 3} is studied by using the one-dimensional quantum Ising model, where the Ising spin describes the effective lattice polarization of an optical phonon. Two types of electron-phonon couplings are introduced through the modulation of transfer integral via lattice deformations. After the exact diagonalization and the perturbation studies, we find that photo-induced low-density carriers can drastically alter quantum fluctuations when the system locates near the quantum critical point between the quantum para- and ferro-electric phases.

  7. Quantum Ising model coupled with conducting electrons

    Science.gov (United States)

    Yamashita, Yasufumi; Yonemitsu, Kenji

    2005-01-01

    The effect of photo-doping on the quantum paraelectric SrTiO3 is studied by using the one-dimensional quantum Ising model, where the Ising spin describes the effective lattice polarization of an optical phonon. Two types of electron-phonon couplings are introduced through the modulation of transfer integral via lattice deformations. After the exact diagonalization and the perturbation studies, we find that photo-induced low-density carriers can drastically alter quantum fluctuations when the system locates near the quantum critical point between the quantum para- and ferro-electric phases.

  8. Multi-level slug tests in highly permeable formations: 2. Hydraulic conductivity identification, method verification, and field applications

    Science.gov (United States)

    Zlotnik, V.A.; McGuire, V.L.

    1998-01-01

    Using the developed theory and modified Springer-Gelhar (SG) model, an identification method is proposed for estimating hydraulic conductivity from multi-level slug tests. The computerized algorithm calculates hydraulic conductivity from both monotonic and oscillatory well responses obtained using a double-packer system. Field verification of the method was performed at a specially designed fully penetrating well of 0.1-m diameter with a 10-m screen in a sand and gravel alluvial aquifer (MSEA site, Shelton, Nebraska). During well installation, disturbed core samples were collected every 0.6 m using a split-spoon sampler. Vertical profiles of hydraulic conductivity were produced on the basis of grain-size analysis of the disturbed core samples. These results closely correlate with the vertical profile of horizontal hydraulic conductivity obtained by interpreting multi-level slug test responses using the modified SG model. The identification method was applied to interpret the response from 474 slug tests in 156 locations at the MSEA site. More than 60% of responses were oscillatory. The method produced a good match to experimental data for both oscillatory and monotonic responses using an automated curve matching procedure. The proposed method allowed us to drastically increase the efficiency of each well used for aquifer characterization and to process massive arrays of field data. Recommendations generalizing this experience to massive application of the proposed method are developed.Using the developed theory and modified Springer-Gelhar (SG) model, an identification method is proposed for estimating hydraulic conductivity from multi-level slug tests. The computerized algorithm calculates hydraulic conductivity from both monotonic and oscillatory well responses obtained using a double-packer system. Field verification of the method was performed at a specially designed fully penetrating well of 0.1-m diameter with a 10-m screen in a sand and gravel alluvial

  9. Application of a new hydraulic conductivity model to simulate rapid groundwater fluctuations in the Eel River watershed in Northern California

    Science.gov (United States)

    Vrettas, M. D.; Fung, I. Y.

    2015-12-01

    High-frequency multi-year observations of the water table at several wells in the Angelo Coast Range Reserve in the Eel River Watershed in northern California show rapid fluctuations, where the water table, some 10-15 meters below the surface, rises by as much as 1 meter in a day or two after the first storms of the rain season. The observations highlight preferential flow through weathered bedrock, which can store as much as 30% of the moisture in the column ("rock moisture"). This rapid transfer of moisture and storage at depth could have a significant impact on ecosystem dynamics and the water and energy budgets of the atmosphere on various time scales. Despite its high importance, preferential flow through weather bedrock is not routinely captured in most climate models. This work presents a new hydraulic conductivity parameterization that captures the preferential flow, with straightforward implementation into current global climate models. The hydraulic conductivity is represented as a product of the effective saturation (normalized water content) and a background hydraulic conductivity Kbkg, drawn from a depth dependent lognormal distribution. A unique feature of the parameterization is that the variance of hydraulic conductivity is large when there is little rock moisture, and decreases with increasing saturation, mimicking flow through fractures. The new method is applied to seven wells locations on a steep (35 degrees) hill-slope in the Eel River watershed in Northern California, for the duration of six years and estimates of the model parameters are provided by assimilating, into Richards' equation, measurements of precipitation [mm] and water table depths [m] at 30-minute time intervals. The simulation results show that the new approach yields a good agreement of the rapid rise of the observed water table at the tested well locations. Furthermore, the water stored in the weathered bedrock is estimated to be in the range between 32% and 41%, which could

  10. Spatial Estimation of Saturated Hydraulic Conductivity from Terrain Attributes Using Regression, Kriging, and Artificial Neural Networks*1

    Institute of Scientific and Technical Information of China (English)

    H. R. MOTAGHIAN; J. MOHAMMADI

    2011-01-01

    Several methods, including stepwise regression, ordinary kriging, cokriging, kriging with external drift, kriging with varying local means, regression-kriging, ordinary artificial neural networks, and kriging combined with artificial neural networks, were compared to predict spatial variation of saturated hydraulic conductivity from environmental covariates. All methods except ordinary kriging allow for inclusion of secondary variables. The secondary spatial information used was terrain attributes including elevation, slope gradient,slope aspect, profile curvature and contour curvature. A multiple jackknifing procedure was used as a validation method. Root mean square error (RMSE) and mean absolute error (MAE) were used as the validation indices, with the mean RMSE and mean MAE used to judge the prediction quality. Prediction performance by ordinary kriging was poor, indicating that prediction of saturated hydraulic conductivity can be improved by incorporating ancillary data such as terrain variables. Kriging combined with artificial neural networks performed best. These prediction models made better use of ancillary information in predicting saturated hydraulic conductivity compared with the competing models. The combination of geostatistical predictors with neural computing techniques offers more capability for incorporating ancillary information in predictive soil mapping. There is great potential for further research and development of hybrid methods for digital soil mapping.

  11. A semi-analytical generalized Hvorslev formula for estimating riverbed hydraulic conductivity with an open-ended standpipe permeameter

    Science.gov (United States)

    Pozdniakov, Sergey P.; Wang, Ping; Lekhov, Mikhail V.

    2016-09-01

    The well-known Hvorslev (1951) formula was developed to estimate soil permeability using single-well slug tests and has been widely applied to determine riverbed hydraulic conductivity using in situ standpipe permeameter tests. Here, we further develop a general solution of the Hvorslev (1951) formula that accounts for flow in a bounded medium and assumes that the bottom of the river is a prescribed head boundary. The superposition of real and imaginary disk sources is used to obtain a semi-analytical expression of the total hydraulic resistance of the flow in and out of the pipe. As a result, we obtained a simple semi-analytical expression for the resistance, which represents a generalization of the Hvorslev (1951). The obtained expression is benchmarked against a finite-element numerical model of 2-D flow (in r-z coordinates) in an anisotropic medium. The results exhibit good agreement between the simulated and estimated riverbed hydraulic conductivity values. Furthermore, a set of simulations for layered, stochastically heterogeneous riverbed sediments was conducted and processed using the proposed expression to demonstrate the potential associated with measuring vertical heterogeneity in bottom sediments using a series of standpipe permeameter tests with different lengths of pipe inserted into the riverbed sediments.

  12. Stochastic fusion of dynamic hydrological and geophysical data for estimating hydraulic conductivities: insights and observations (Invited)

    Science.gov (United States)

    Irving, J. D.; Singha, K.

    2010-12-01

    Traditionally, hydrological measurements have been used to estimate subsurface properties controlling groundwater flow and contaminant transport. However, such measurements are limited by their support volume and expense. A considerable benefit of geophysical measurements is that they provide a degree of spatial coverage and resolution that are unattainable with other methods, and the data can be acquired in a cost-effective manner. In particular, dynamic geophysical data allow us to indirectly observe changes in hydrological state variables as flow and transport processes occur, and can thus provide a link to hydrological properties when coupled with a process-based model. Stochastic fusion of these two data types offers the potential to provide not only estimates of subsurface hydrological properties, but also a quantification of their uncertainty. This information is critical when considering the end use of the data, which may be for groundwater remediation and management decision making. Here, we examine a number of key issues in the stochastic fusion of dynamic hydrogeophysical data. We focus our attention on the specific problem of integrating time-lapse crosshole electrical resistivity measurements and saline tracer-test concentration data in order to estimate the spatial distribution of hydraulic conductivity (K). To assimilate the geophysical and hydrological measurements in a stochastic manner, we use a Bayesian Markov-chain-Monte-Carlo (McMC) methodology. This provides multiple realizations of the subsurface K field that are consistent with the measured data and assumptions regarding model structure and data errors. To account for incomplete petrophysical knowledge, the geophysical and hydrological forward models are linked through an uncertain relationship between electrical resistivity and concentration following the general form of Archie’s law. To make the spatially distributed, fully stochastic inverse problem computationally tractable, we take

  13. Effects of variations in hydraulic conductivity and flow conditions on groundwater flow and solute transport in peatlands

    Energy Technology Data Exchange (ETDEWEB)

    Kellner, Erik [Dept. of Forest Ecology, Univ. of Helsinki (Finland)

    2007-02-15

    In this report it is examined to what extent the variation in hydraulic conductivity within a peatland and adjoining sediments would affect the flow patterns within it under some certain hydraulic-head gradients and other certain border conditions. The first part of the report contains a short review of organic and mineral-soil sediment types and characteristics and what we know about present peatlands and underlying sediments in the SKB investigation areas today. In the next part, a 2-dimensional model is used to simulate flows and transports in different settings of a peatland, with the objective of studying the effects of some particular factors: 1. The magnitude of the hydraulic conductivity of the peat and of underlying layers. 2. Presence and positions of cracks in underlying clay layers. 3. Anisotropy and heterogeneity in peat hydraulic conductivity. 4. The size of the water recharge at the peatland surface. 5. The seasonal variation of the water recharge. The modelling results show that the importance of flow direction decreases with decreasing hydraulic conductivity in the peatland. This occurs as the convective flux is slowed down and the transport is taken over by the diffusive flux. Because the lowest hydraulic conductivity layer to large extent determines the size of the flow, presence of a low-conductivity layer, such as a layer of clay, is an important factor. Presence of cracks in such tight layers can increase the transport of solutes into the peat. The highest inflow rates are reached when such cracks occur in discharge areas with strong upward flow. On the other hand, a conservative solute can spread efficiently if there is a crack in low-flow locations. The effect of anisotropy is found to be small, partly because the horizontal gradients become smaller as distances are larger. The effect of layers with high or low permeability varies depending on the location and the prevailing gradients. One tight layer has a strong effect on the flow pattern

  14. Inferring the heterogeneity, transmissivity and hydraulic conductivity of crystalline aquifers from a detailed water-table map

    Science.gov (United States)

    Dewandel, Benoît; Jeanpert, Julie; Ladouche, Bernard; Join, Jean-Lambert; Maréchal, Jean-Christophe

    2017-07-01

    Estimating the transmissivity or hydraulic conductivity field to characterize the heterogeneity of a crystalline aquifer is particularly difficult because of the wide variations of the parameters. We developed a new approach based on the analysis of a dense network of water-table data. It is based on the concept that large-scale variations in hydraulic head may give information on large-scale aquifer parameters. The method assumes that flux into the aquifer is mainly sub-horizontal and that the water table is mostly controlled by topography, rather than recharge. It is based on an empirical statistical relationship between field data on transmissivity and the inverse slope values of a topography-reduced water-table map. This relationship is used to compute a transmissivity map that must be validated with field measurements. The proposed approach can provide a general pattern of transmissivity, or hydraulic conductivity, but cannot correctly reproduce strong variations at very local scale (less than10 m), and will face of some uncertainties where vertical flows cannot be neglected. The method was tested on a peridotite (ultramafic rock) aquifer of 3.5 km2 in area located in New Caledonia. The resulting map shows transmissivity variations over about 5 orders of magnitude (average LogT: -5.2 ± 0.7). Comparison with a map based on measured water-level data (n = 475) shows that the comparison between LogT-computed values and LogT data deduced from 28 hydraulic tests is estimated with an error less than 20% in 71% of cases (LogT ± 0.4), and with an error less than 10% (LogT ± 0.2 on average) in 39% of cases. From this map a hydraulic-conductivity map has been computed showing values ranging over 8 orders of magnitude. The repeatability of the approach was tested on a second data set of hydraulic-head measurements (n = 543); the mean deviation between both LogT maps is about 11%. These encouraging results show that the method can give valuable parameter estimates, and

  15. Effects of the hydraulic conductivity of the matrix/macropore interface on cumulative infiltrations into dual-permeability media

    Science.gov (United States)

    Lassabatere, L.; Peyrard, X.; Angulo-Jaramillo, R.; Simunek, J.

    2009-12-01

    Modeling of water infiltration into the vadose zone is important for better understanding of movement of water-transported contaminants. There is a great need to take into account the soil heterogeneity and, in particular, the presence of macropores or cracks that could generate preferential flow. Several mathematical models have been proposed to describe unsaturated flow through heterogeneous soils. The dual-permeability model (referred to as the 2K model) assumes that flow is governed by Richards equation in both porous regions (matrix and macropores). Water can be exchanged between the two regions following a first-order rate law. Although several studies have dealt with such modeling, no study has evaluated the influence of the hydraulic conductivity of the matrix/macropore interface on water cumulative infiltration. And this is the focus of this study. An analytical scaling method reveals the role of the following main parameters for given boundary and initial conditions: the saturated hydraulic conductivity ratio (R_Ks), the water pressure scale parameter ratio (R_hg), the saturated volumetric water content ratio (R_θs), and the shape parameters of the water retention and hydraulic conductivity functions. The last essential parameter is related to the interfacial hydraulic conductivity (Ka) between the macropore and matrix regions. The scaled 2K flow equations were solved using HYDRUS-1D 4.09 for the specific case of water infiltrating into an initially uniform soil profile and a zero pressure head at the soil surface. A sensitivity of water infiltration was studied for different sets of scale parameters (R_Ks, R_hg, R_θs, and shape parameters) and the scaled interfacial conductivity (Ka). Numerical results illustrate two extreme behaviors. When the interfacial conductivity is zero (i.e., no water exchange), water infiltrates separately into matrix and macropore regions, producing a much deeper moisture front in the macropore domain. In the opposite case

  16. Fracture hydraulic conductivity in the Mexico City clayey aquitard: Field piezometer rising-head tests

    Science.gov (United States)

    Vargas, Carlos; Ortega-Guerrero, Adrián

    A regional lacustrine aquitard covers the main aquifer of the metropolitan area of Mexico City. The aquitard's hydraulic conductivity (K') is fundamental for evaluating the natural protection of the aquifer against a variety of contaminants present on the surface and its hydraulic response. This study analyzes the distribution and variation of K' in the plains of Chalco, Texcoco and Mexico City (three of the six former lakes that existed in the Basin of Mexico), on the basis of 225 field-permeability tests, in nests of existing piezometers located at depths of 2-85 m. Tests were interpreted using the Hvorslev method and some by the Bouwer-Rice method. Results indicate that the distribution of K' fits log-Gaussian regression models. Dominant frequencies for K' in the Chalco and Texcoco plains range between 1E-09 and 1E-08 m/s, with similar population means of 1.19E-09 and 1.7E-09 m/s, respectively, which are one to two orders of magnitude higher than the matrix conductivity. In the Mexico City Plain the population mean is near by one order of magnitude lower; K'=2.6E-10 m/s. The contrast between the measured K' and that of the matrix is attributed to the presence of fractures in the upper 25-40 m, which is consistent with the findings of previous studies on solute migration in the aquitard. Un imperméable régional d'origine lacustre recouvre le principal aquifère de la zone urbaine de la ville de Mexico. La conductivité hydraulique K' de cet imperméable est fondamentale pour évaluer la protection naturelle de l'aquifère, contre les différents contaminants présents en surface, et sa réponse hydraulique. Cette étude analyse et les variations de K' dans les plaines de Chalco, Texcoco et Mexico (trois des six anciens lacs qui existaient dans le Bassin de Mexico), sur la base de 225 essais de perméabilité sur le terrain, réalisés en grappes dans des piézomètres existants entre 2 et 85 m de profondeur. Les essais ont été interprétés avec la m

  17. Parallel Electron-Hole Bilayer Conductivity from Electronic Interface Reconstruction

    NARCIS (Netherlands)

    Pentcheva, R.; Huijben, M.; Otte, K.; Pickett, W.E.; Kleibeuker, J.E.; Huijben, J.; Boschker, H.; Kockmann, D.; Siemons, W.; Koster, G.; Zandvliet, H.J.W.; Rijnders, G.; Blank, D.H.A.; Hilgenkamp, H.; Brinkman, A.

    2010-01-01

    The perovskite SrTiO3-LaAlO3 structure has advanced to a model system to investigate the rich electronic phenomena arising at polar oxide interfaces. Using first principles calculations and transport measurements we demonstrate that an additional SrTiO3 capping layer prevents atomic reconstruction a

  18. The hydraulic conductance of Fraxinus ornus leaves is constrained by soil water availability and coordinated with gas exchange rates.

    Science.gov (United States)

    Gortan, Emmanuelle; Nardini, Andrea; Gascó, Antonio; Salleo, Sebastiano

    2009-04-01

    Leaf hydraulic conductance (Kleaf) is known to be an important determinant of plant gas exchange and photosynthesis. Little is known about the long-term impact of different environmental factors on the hydraulic construction of leaves and its eventual consequences on leaf gas exchange. In this study, we investigate the impact of soil water availability on Kleaf of Fraxinus ornus L. as well as the influence of Kleaf on gas exchange rates and plant water status. With this aim, Kleaf, leaf conductance to water vapour (gL), leaf water potential (Psileaf) and leaf mass per area (LMA) were measured in F. ornus trees, growing in 21 different sites with contrasting water availability. Plants growing in arid sites had lower Kleaf, gL and Psileaf than those growing in sites with higher water availability. On the contrary, LMA was similar in the two groups. The Kleaf values recorded in sites with two different levels of soil water availability were constantly different from each other regardless of the amount of precipitation recorded over 20 days before measurements. Moreover, Kleaf was correlated with gL values. Our data suggest that down-regulation of Kleaf is a component of adaptation of plants to drought-prone habitats. Low Kleaf implies reduced gas exchange which may, in turn, influence the climatic conditions on a local/regional scale. It is concluded that leaf hydraulics and its changes in response to resource availability should receive greater attention in studies aimed at modelling biosphere-atmosphere interactions.

  19. Optical Conductivity of Graphene Sheet Including Electron-Phonon Interaction

    Institute of Scientific and Technical Information of China (English)

    Hamze Mousavi

    2012-01-01

    Using an expression of optical conductivity, based on the linear response theory, the Green's function technique and within the Holstein Hamiltonian model, the effect of electron-phonon interaction on the optical conductivity of graphene plane is studied. It is found that the electron-phonon coupling increases the optical conductivity of graphene sheet in the low frequency region due to decreasing quasiparticle weight of electron excitation while the optical conductivity reduces in the high frequency region. The latter is due to role of electrical field's frequency.

  20. Bundle-sheath aquaporins play a role in controlling Arabidopsis leaf hydraulic conductivity.

    Science.gov (United States)

    Sade, Nir; Shatil-Cohen, Arava; Moshelion, Menachem

    2015-01-01

    The role of molecular mechanisms in the regulation of leaf hydraulics (K(leaf)) is still not well understood. We hypothesized that aquaporins (AQPs) in the bundle sheath may regulate K(leaf). To examine this hypothesis, AQP genes were constitutively silenced using artificial microRNAs and recovery was achieved by targeting the expression of the tobacco AQP (NtAQP1) to bundle-sheath cells in the silenced plants. Constitutively silenced PIP1 plants exhibited decreased PIP1 transcript levels and decreased K(leaf). However, once the plants were recovered with NtAQP1, their K(leaf) values were almost the same as those of WT plants. We also demonstrate the important role of ABA, acting via AQP, in that recovery and K(leaf) regulation. These results support our previously raised hypothesis concerning the role of bundle-sheath AQPs in the regulation of leaf hydraulics.

  1. A multiscale approach to determine hydraulic conductivity in thick claystone aquitards using field, laboratory, and numerical modeling methods

    Science.gov (United States)

    Smith, L. A.; Barbour, S. L.; Hendry, M. J.; Novakowski, K.; van der Kamp, G.

    2016-07-01

    Characterizing the hydraulic conductivity (K) of aquitards is difficult due to technical and logistical difficulties associated with field-based methods as well as the cost and challenge of collecting representative and competent core samples for laboratory analysis. The objective of this study was to produce a multiscale comparison of vertical and horizontal hydraulic conductivity (Kv and Kh, respectively) of a regionally extensive Cretaceous clay-rich aquitard in southern Saskatchewan. Ten vibrating wire pressure transducers were lowered into place at depths between 25 and 325 m, then the annular was space was filled with a cement-bentonite grout. The in situ Kh was estimated at the location of each transducer by simulating the early-time pore pressure measurements following setting of the grout using a 2-D axisymmetric, finite element, numerical model. Core samples were collected during drilling for conventional laboratory testing for Kv to compare with the transducer-determined in situ Kh. Results highlight the importance of scale and consideration of the presence of possible secondary features (e.g., fractures) in the aquitard. The proximity of the transducers to an active potash mine (˜1 km) where depressurization of an underlying aquifer resulted in drawdown through the aquitard provided a unique opportunity to model the current hydraulic head profile using both the Kh and Kv estimates. Results indicate that the transducer-determined Kh estimates would allow for the development of the current hydraulic head distribution, and that simulating the pore pressure recovery can be used to estimate moderately low in situ Kh (<10-11 m s-1).

  2. Drought effects on hydraulic conductivity and xylem vulnerability to embolism in diverse species and provenances of Mediterranean cedars.

    Science.gov (United States)

    Ladjal, Mehdi; Huc, Roland; Ducrey, Michel

    2005-09-01

    We studied hydraulic traits of young plants of the Mediterranean cedar species Cedrus atlantica (Endl.) G. Manetti ex Carrière (Luberon, France), C. brevifolia (Hook. f.) Henry (Cyprus), C. libani A. Rich (Hadeth El Jebbe, Lebanon) and C. libani (Armut Alani, Turkey). With an optimum water supply, no major differences were observed among species or provenances in either stem hydraulic conductivity (Ks) or leaf specific conductivity (Kl) measured on the main shoot. A moderate soil drought applied for 10 weeks induced marked acclimation through a reduction in Ks, particularly in the Lebanese provenance of C. libani, and a decrease in tracheid lumen size in all species. Cedrus atlantica, which had the smallest tracheids, was the species most vulnerable to embolism: a 50% loss in hydraulic conductivity (PsiPLC50) occurred at a water potential of -4.4 MPa in the well-watered treatment, and at -6.0 MPa in the moderate drought treatment. In the other species, PsiPLC50 was unaffected by moderate soil drought, and only declined sharply at water potentials between -6.4 and -7.5 MPa in both irrigation treatments. During severe drought, Ks of twigs and stomatal conductance (g(s)) were measured simultaneously as leaf water potential declined. For all species, lower vulnerability to embolism based on loss of Ks was recorded on current-year twigs. The threshold for stomatal closure (10% of maximum g(s)) was reached at a predawn water potential (Psi(pd)) of -2.5 MPa in C. atlantica (Luberon) and at -3.1 MPa in C. libani (Lebanon), whereas the other provenance and species had intermediate Psi(pd) values. Cedrus brevifolia, with a Psi(pd) (-3.0 MPa) close to that of C. libani (Lebanon), had the highest stomatal conductance of the study species. The importance of a margin of safety between water potential causing stomatal closure and that causing xylem embolism induction is discussed.

  3. Tree level hydrodynamic approach for resolving aboveground water storage and stomatal conductance and modeling the effects of tree hydraulic strategy

    Science.gov (United States)

    Mirfenderesgi, Golnazalsadat; Bohrer, Gil; Matheny, Ashley M.; Fatichi, Simone; Moraes Frasson, Renato Prata; Schäfer, Karina V. R.

    2016-07-01

    The finite difference ecosystem-scale tree crown hydrodynamics model version 2 (FETCH2) is a tree-scale hydrodynamic model of transpiration. The FETCH2 model employs a finite difference numerical methodology and a simplified single-beam conduit system to explicitly resolve xylem water potentials throughout the vertical extent of a tree. Empirical equations relate water potential within the stem to stomatal conductance of the leaves at each height throughout the crown. While highly simplified, this approach brings additional realism to the simulation of transpiration by linking stomatal responses to stem water potential rather than directly to soil moisture, as is currently the case in the majority of land surface models. FETCH2 accounts for plant hydraulic traits, such as the degree of anisohydric/isohydric response of stomata, maximal xylem conductivity, vertical distribution of leaf area, and maximal and minimal xylem water content. We used FETCH2 along with sap flow and eddy covariance data sets collected from a mixed plot of two genera (oak/pine) in Silas Little Experimental Forest, NJ, USA, to conduct an analysis of the intergeneric variation of hydraulic strategies and their effects on diurnal and seasonal transpiration dynamics. We define these strategies through the parameters that describe the genus level transpiration and xylem conductivity responses to changes in stem water potential. Our evaluation revealed that FETCH2 considerably improved the simulation of ecosystem transpiration and latent heat flux in comparison to more conventional models. A virtual experiment showed that the model was able to capture the effect of hydraulic strategies such as isohydric/anisohydric behavior on stomatal conductance under different soil-water availability conditions.

  4. Suppression of Electron Thermal Conduction in High $\\beta$ Plasma

    CERN Document Server

    Roberg-Clark, G T; Reynolds, C S; Swisdak, M

    2016-01-01

    Electron heat conduction is explored with particle-in-cell simulations and analytic modeling in a high $\\beta$ system relevant to galaxy clusters. Linear wave theory reveals that whistler waves are driven unstable by electron heat flux even when the heat flux is weak. The resonant interaction of electrons with these waves plays a critical role in controlling the impact of the waves on the heat flux. In a 1D model only electrons moving opposite in direction to the heat flux resonate with the waves and electron heat flux is only modestly reduced. In a 2D system transverse whistlers also resonate with electrons propagating in the direction of the heat flux and resonant overlap leads to strong suppression of electron heat flux. The results suggest that electron heat conduction might be strongly suppressed in galaxy clusters.

  5. Characterization and Analysis of Conductance: From Polymers to Single Electrons

    OpenAIRE

    Tallarida, Nicholas Ryan

    2016-01-01

    Experimental studies on the conductive properties of molecular systems led to the discovery and characterization of two essential elements of molecular electronics: a molecularwire and a single electron switch. The synthesis and cyclic current versus voltage (I/V) measurements of intrinsically conductive linear chain [-Ag-S-BP-S-]n polymers determined their relatively large conductivity and suggested that mobile Ag adatoms on the roughened Ag surface catalyzed the polymerization. On the other...

  6. Scalable Generalization of Hydraulic Conductivity in Quaternary Strata for Use in a Regional Groundwater Model

    Science.gov (United States)

    Jatnieks, J.; Popovs, K.; Klints, I.; Timuhins, A.; Kalvans, A.; Delina, A.; Saks, T.

    2012-04-01

    The cover of Quaternary sediments especially in formerly glaciated territories usually is the most complex part of the sedimentary sequences. In regional hydro-geological models it is often assumed as a single layer with uniform or calibrated properties (Valner 2003). However, the properties and structure of Quaternary sediments control the groundwater recharge: it can either direct the groundwater flow horizontally towards discharge in topographic lows or vertically, recharging groundwater in the bedrock. This work aims to present calibration results and detail our experience while integrating a scalable generalization of hydraulic conductivity for Quaternary strata in the regional groundwater modelling system for the Baltic artesian basin - MOSYS V1. We also present a method for solving boundary transitions between spatial clusters of lithologically similar structure. In this study the main unit of generalization is the spatial cluster. Clusters are obtained from distance calculations combining the Normalized Compression Distance (NCD) metric, calculated by the CompLearn parameter-free machine learning toolkit, with normalized Euclidean distance measures for coordinates of the borehole log data. A hierarchical clustering solution is used for obtaining cluster membership identifier for each borehole. Using boreholes as generator points for Voronoi tessellation and dissolving resulting polygons according to their cluster membership attribute, allows us to obtain spatial regions representing a certain degree of similarity in lithological structure. This degree of similarity and the spatial heterogeneity of the cluster polygons can be varied by different flattening of the hierarchical cluster model into variable number of clusters. This provides a scalable generalization solution which can be adapted according to model calibration performance. Using the dissimilarity matrix of the NCD metric, a borehole most similar to all the others from the lithological structure

  7. Electron heat conductivity of epitaxial graphene on silicon carbide

    Science.gov (United States)

    Alisultanov, Z. Z.; Meilanov, R. P.

    2016-08-01

    The diagonal component of the electron heat conductivity tensor of epitaxial graphene formed in a semiconductor has been investigated within a simple analytical model. It is shown that the heat conductivity sharply changes at a chemical potential close to the substrate band gap edge. Low-temperature expressions for the heat conductivity are derived.

  8. The perceptual trap: Experimental and modelling examples of soil moisture, hydraulic conductivity and response units in complex subsurface settings.

    Science.gov (United States)

    Jackisch, Conrad; Demand, Dominic; Allroggen, Niklas; Loritz, Ralf; Zehe, Erwin

    2017-04-01

    In order to discuss hypothesis testing in hydrology, the question of the solid foundation of such tests has to be answered. But how certain are we about our measurements of the components of the water balance and the states and dynamics of the complex systems? What implicit assumptions or bias are already embedded in our perception of the processes? How can we find light in the darkness of heterogeneity? We will contribute examples from experimental findings, modelling approaches and landscape analysis to the discussion. Example soil moisture and the soil continuum: The definition of soil moisture as fraction of water in the porous medium assumes locally well-mixed conditions. Moreover, a unique relation of soil water retention presumes instant local thermodynamic equilibrium in the pore water arrangement. We will show findings from soil moisture responses to precipitation events, from irrigation experiments, and from a model study of initial infiltration velocities. The results highlight, that the implicit assumption relating soil moisture state dynamics with actual soil water flow is biased towards the slow end of the actual velocity distribution and rather blind for preferential flow acting in a very small proportion of the pore space. Moreover, we highlight the assumption of a well-defined continuum during the extrapolation of point-scale measurements and why spatially and temporally continuous observation techniques of soil water states are essential for advancing our understanding and development of subsurface process theories. Example hydraulic conductivity: Hydraulic conductivity lies at the heart of hydrological research and modelling. Its values can range across several orders of magnitude at a single site alone. Yet, we often consider it a crisp, effective parameter. We have conducted measurements of soil hydraulic conductivity in the lab and in the field. Moreover, we assessed infiltration capacity and conducted plot-scale irrigation experiments to

  9. Status of the art: hydraulic conductivity of acid- fractures; Condutividade hidraulica de fratura acida: estado da arte

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Valdo Ferreira [Universidade Estadual do Norte Fluminense Darcy Ribeiro (LENEP/UENF), Macae, RJ (Brazil). Centro de Ciencia e Tecnologia. Lab. de Engenharia e Exploracao de Petroleo; Campos, Wellington [PETROBRAS, RJ (Brazil). E and P Engenharia de Producao. Gerencia de Completacao e Avaliacao], e-mail: wcampos@petrobras.com.br

    2010-06-15

    This paper presents a review of the hydraulic conductivity models developed for acid fractures in almost four decades of studies in petroleum engineering. These studies have often benefited from theories and experiments carried out in areas of knowledge such as physics, geology, hydrology, fluid mechanics, rock mechanics and tribology. The review showed that the pioneer study of Nierode and Kruk (1973) is still used in commercial software and influences the current studies. There was significant evolution on the quantitative surface topography characterization of the fractures and their impact on the hydraulic conductivity. The same occurred for the effects of acid dissolution on the rock resistance. Improvements on correlations similar to the Nierode and Kruk can be applied at once on the acid fracturing project and evaluation practice for the cases of rough dissolution pattern. A method to consider the overall conductivity from heterogeneous channels and roughness pattern was recently proposed. The complexity of the theoretical fundaments, specially the range of validity of the equations in face of the simplifications assumed, the difficulty of performing representative laboratory and field experiments, the difficulty of characterizing quantitatively the fractures surface topography and its effects on the conductivity, and the large variety of rocks and acid systems keep this subject open for research. (author)

  10. Reduced content of homogalacturonan does not alter the ion-mediated increase in xylem hydraulic conductivity in tobacco.

    Science.gov (United States)

    Nardini, Andrea; Gascó, Antonio; Cervone, Felice; Salleo, Sebastiano

    2007-04-01

    Xylem hydraulic conductivity (K(s)) in stems of tobacco (Nicotiana tabacum) wild-type SR1 was compared to that of PG7 and PG16, two transgenic lines with increased levels of expression of the gene encoding the Aspergillus niger endopolygalacturonase (AnPGII). Activity of AnPGII removes in planta blocks of homogalacturonan (HG) with deesterified carboxyls, thus increasing the degree of neutrality of pectins. The effect of K+ was tested in increasing stem K(s) using model plants with more neutral polysaccharides in primary walls and, hence, in intervessel pit membranes. K(s) measured with deionized water was compared to that with KCl solutions at increasing concentrations (DeltaK(s), %). Plants transformed for HG degree of neutrality showed a dwarfed phenotype, but DeltaK(s) did not differ among the three experimental groups. The ion-mediated hydraulic effect saturated at a KCl concentration of 25 mm in SR1 plants. All the three tobacco lines showed DeltaK(s) of around +12.5% and +17.0% when perfused with 10 and 25 mm KCl, respectively. Because modification of HG content did not influence ion-mediated hydraulic enhancement, we suggest that pectin components other than HG, like rhamnogalacturonan-I and/or rhamnogalacturonan-II, might play important roles in the hydrogel behavior of pit membranes.

  11. Hydraulic conductivity and aquaporin transcription in roots of trembling aspen (Populus tremuloides) seedlings colonized by Laccaria bicolor.

    Science.gov (United States)

    Xu, Hao; Cooke, Janice E K; Kemppainen, Minna; Pardo, Alejandro G; Zwiazek, Janusz J

    2016-07-01

    Ectomycorrhizal fungi have been reported to increase root hydraulic conductivity (L pr) by altering apoplastic and plasma membrane intrinsic protein (PIP)-mediated cell-to-cell water transport pathways in associated roots, or to have little effect on root water transport, depending on the interacting species and imposed stresses. In this study, we investigated the water transport properties and PIP transcription in roots of aspen (Populus tremuloides) seedlings colonized by the wild-type strain of Laccaria bicolor and by strains overexpressing a major fungal water-transporting aquaporin JQ585595. Inoculation of aspen seedlings with L. bicolor resulted in about 30 % colonization rate of root tips, which developed dense mantle and the Hartig net that was restricted in the modified root epidermis. Transcript abundance of the aspen aquaporins PIP1;2, PIP2;1, and PIP2;2 decreased in colonized root tips. Root colonization by JQ585595-overexpressing strains had no significant impact on seedling shoot water potentials, gas exchange, or dry mass; however, it led to further decrease in transcript abundance of PIP1;2 and PIP2;3 and the significantly lower L pr than in non-inoculated roots. These results, taken together with our previous study that showed enhanced root water hydraulics of L. bicolor-colonized white spruce (Picea glauca), suggest that the impact of L. bicolor on root hydraulics varies by the ectomycorrhiza-associated tree species.

  12. Temporal changes of hydraulic conductivity of cultivated soil studied with help of multipoint tension infiltrometer and X-ray computed tomography

    Science.gov (United States)

    Klipa, Vladimir; Zumr, David; Snehota, Michal; Dohnal, Michal

    2016-04-01

    Soil aggregates, its shape, size and spatial distribution affect the pores arrangement and thus govern the hydraulic conductivity of soil and soil moisture regime. On arable lands the soil is exposed to rapid structural changes within each growing season due to agrotechnical practices, quick crop and root growth, soil biota and climatic conditions. This contribution is mainly focused on temporal changes of unsaturated hydraulic conductivity of cultivated soil. The research is supplemented by detailed analysis of CT images of soil samples for better understanding of structural change of soil during the year and its impact on soil hydraulic conductivity. The infiltration experiments were done using automated multipoint tension infiltrometer recently developed at CTU in Prague on the plots located on the Nucice experimental catchment. The catchment is situated in a moderately hilly area in central Bohemia (Czech Republic). Fourteen regular infiltration campaigns (77 individual infiltration experiments) were conducted from October 2012 until July 2015 on a single arable plot. In general, agricultural practice captured involved complete life cycle from sowing, through harvest, to postharvest stubble breaking. Weather conditions during infiltration experiments ranged from clear-sky to light rain, with temperatures between 8 and 30°C. All measurements were consistently performed with small suction of 3 cm and hydraulic conductivities were determined using extended semiempirical estimation procedure of Zhang. Results show that unsaturated hydraulic conductivity was the lowest in early spring and did increase at beginning of summer in the years 2012 - 2014. During the summer and autumn (2012 - 2014) the unsaturated hydraulic conductivity remained relatively unchanged. On the contrary, results in the year 2015 show opposite trend - the highest hydraulic conductivity was observed in early spring and did gradually decrease until the end of July. In both cases, however, the

  13. Digital map of hydraulic conductivity for the High Plains aquifer in parts of Colorado, Kansas, Nebraska, New Mexico, Oklahoma, South Dakota, Texas, and Wyoming

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This digital data set consists of hydraulic conductivity contours and polygons for the High Plains aquifer in the central United States. The High Plains aquifer...

  14. Effects of Phosphorus Nutrient on the Hydraulic Conductivity of Sorghum (Sorghum vulgare Pers.) Seedling Roots Under Water Deficiency

    Institute of Scientific and Technical Information of China (English)

    Zhou-Ping SHANGGUAN; Ting-Wu LEI; Ming-An SHAO; Qing-Wu XUE

    2005-01-01

    Hydroponic experiments were conducted in a growth chamber and changes in the hydraulic conductivity of sorghum (Sorghum vulgare Pers.) roots (Lpr) at the three-leaf stage were measured using the pressure chamber method. Water deficiency was imposed with polyethylene glycol (PEG) 6000 and the phosphorus (P) levels were controlled by complete Hoagland solution with and without P nutrient. The objective of this study was to investigate the effect of P nutrition on root Lpr under water deficiency. The results showed that the Lpr in P deficiency treatments decreased markedly, but the Lpr recovered to the same value as that of control when sufficient P was supplied for 4-24 h. Water deficiency decreased Lpr, but the hydraulic conductivity of the roots with sufficient P supply was still higher than that of plants without P supply. When resuming water supply, the Lpr of the water-deficient plants under P supply recovered faster than that of plants without P supply, which indicates that plants with sufficient P nutrient are more drought tolerant and have a greater ability to recover after drought. The treatment of HgCl2 indicated that P nutrient could regulate the Lpr by affecting the activity and the expression levels of aquaporins.

  15. Interpretation of Flow Logs from Nevada Test Site Boreholes to Estimate Hydraulic Conductivity Using Numerical Simulations Constrained by Single-Well Aquifer Tests

    Science.gov (United States)

    Garcia, C. Amanda; Halford, Keith J.; Laczniak, Randell J.

    2010-01-01

    Hydraulic conductivities of volcanic and carbonate lithologic units at the Nevada Test Site were estimated from flow logs and aquifer-test data. Borehole flow and drawdown were integrated and interpreted using a radial, axisymmetric flow model, AnalyzeHOLE. This integrated approach is used because complex well completions and heterogeneous aquifers and confining units produce vertical flow in the annular space and aquifers adjacent to the wellbore. AnalyzeHOLE simulates vertical flow, in addition to horizontal flow, which accounts for converging flow toward screen ends and diverging flow toward transmissive intervals. Simulated aquifers and confining units uniformly are subdivided by depth into intervals in which the hydraulic conductivity is estimated with the Parameter ESTimation (PEST) software. Between 50 and 150 hydraulic-conductivity parameters were estimated by minimizing weighted differences between simulated and measured flow and drawdown. Transmissivity estimates from single-well or multiple-well aquifer tests were used to constrain estimates of hydraulic conductivity. The distribution of hydraulic conductivity within each lithology had a minimum variance because estimates were constrained with Tikhonov regularization. AnalyzeHOLE simulated hydraulic-conductivity estimates for lithologic units across screened and cased intervals are as much as 100 times less than those estimated using proportional flow-log analyses applied across screened intervals only. Smaller estimates of hydraulic conductivity for individual lithologic units are simulated because sections of the unit behind cased intervals of the wellbore are not assumed to be impermeable, and therefore, can contribute flow to the wellbore. Simulated hydraulic-conductivity estimates vary by more than three orders of magnitude across a lithologic unit, indicating a high degree of heterogeneity in volcanic and carbonate-rock units. The higher water transmitting potential of carbonate-rock units relative

  16. Interpretation of Flow Logs from Nevada Test Site Boreholes to Estimate Hydraulic conductivity Using Numerical Simulations Constrained by Single-Well Aquifer Tests

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, C. Amanda; Halford, Keith J.; Laczniak, Randell J.

    2010-02-12

    Hydraulic conductivities of volcanic and carbonate lithologic units at the Nevada Test Site were estimated from flow logs and aquifer-test data. Borehole flow and drawdown were integrated and interpreted using a radial, axisymmetric flow model, AnalyzeHOLE. This integrated approach is used because complex well completions and heterogeneous aquifers and confining units produce vertical flow in the annular space and aquifers adjacent to the wellbore. AnalyzeHOLE simulates vertical flow, in addition to horizontal flow, which accounts for converging flow toward screen ends and diverging flow toward transmissive intervals. Simulated aquifers and confining units uniformly are subdivided by depth into intervals in which the hydraulic conductivity is estimated with the Parameter ESTimation (PEST) software. Between 50 and 150 hydraulic-conductivity parameters were estimated by minimizing weighted differences between simulated and measured flow and drawdown. Transmissivity estimates from single-well or multiple-well aquifer tests were used to constrain estimates of hydraulic conductivity. The distribution of hydraulic conductivity within each lithology had a minimum variance because estimates were constrained with Tikhonov regularization. AnalyzeHOLE simulated hydraulic-conductivity estimates for lithologic units across screened and cased intervals are as much as 100 times less than those estimated using proportional flow-log analyses applied across screened intervals only. Smaller estimates of hydraulic conductivity for individual lithologic units are simulated because sections of the unit behind cased intervals of the wellbore are not assumed to be impermeable, and therefore, can contribute flow to the wellbore. Simulated hydraulic-conductivity estimates vary by more than three orders of magnitude across a lithologic unit, indicating a high degree of heterogeneity in volcanic and carbonate-rock units. The higher water transmitting potential of carbonate-rock units relative

  17. Xylem embolism alleviated by ion-mediated increase in hydraulic conductivity of functional xylem: insights from field measurements.

    Science.gov (United States)

    Trifilò, Patrizia; Lo Gullo, Maria A; Salleo, Sebastiano; Callea, Katia; Nardini, Andrea

    2008-10-01

    Recent studies have shown that, in some species, xylem hydraulic conductivity (K(h)) increases with increasing cation concentration of xylem sap. Evidence indicates that K(h) increases as a result of the de-swelling of pit membrane pectins caused by cation neutralization of polygalacturonanes. We tested whether this ionic effect partly compensates for the embolism-induced loss of stem hydraulic conductivity (PLC) by increasing K(h) of functioning conduits. We report changes in PLC, leaf water status and potassium concentration ([K(+)]) of xylem sap measured in April and July in two evergreens (Ceratonia siliqua L. and Phytolacca dioica L.) and one deciduous tree (Platanus orientalis L.) growing in the field in Sicily. In summer, Ceratonia siliqua and Phytolacca dioica showed similar native embolism (PLC = 30-40%) and [K(+)] of xylem sap (14 to 17 mM), and K(h) of stems perfused with 10 to 25 mM KCl increased by 15 to 18% compared with K(h) of stems perfused with a low concentration of a multi-ionic solution. In contrast, native [K(+)] of sap of Platanus orientalis was 50% of that in the two evergreens in summer, with a parallel lack of detectable changes in PLC that was below 10% in both spring and summer. The ionic effect was PLC-dependent: the enhancement of K(h) induced by 10 to 25 mM KCl changed from 15% for fully hydrated stems to 50-75% for stems with PLC = 50%. In Ceratonia siliqua, PLC was less than 10% in spring and about 40% in summer; concurrently, xylem sap [K(+)] increased from 3 to about 15 mM. This [K(+)] at the recorded PLC would cause an increase in residual K(h) of about 30%. Hence, the actual reduction in water transport capacity of Ceratonia siliqua stems in summer is about 20%. Similar calculations for Phytolacca dioica suggest that the actual loss of hydraulic conductivity in stems of this species in summer would be only about 10%, and not 30% as suggested by hydraulic measurements performed in the laboratory. We conclude that an increase in

  18. Water uptake by growing cells: an assessment of the controlling roles of wall relaxation, solute uptake, and hydraulic conductance

    Science.gov (United States)

    Cosgrove, D. J.

    1993-01-01

    Growing plant cells increase in volume principally by water uptake into the vacuole. There are only three general mechanisms by which a cell can modulate the process of water uptake: (a) by relaxing wall stress to reduce cell turgor pressure (thereby reducing cell water potential), (b) by modifying the solute content of the cell or its surroundings (likewise affecting water potential), and (c) by changing the hydraulic conductance of the water uptake pathway (this works only for cells remote from water potential equilibrium). Recent studies supporting each of these potential mechanisms are reviewed and critically assessed. The importance of solute uptake and hydraulic conductance is advocated by some recent studies, but the evidence is indirect and conclusions remain controversial. For most growing plant cells with substantial turgor pressure, it appears that reduction in cell turgor pressure, as a consequence of wall relaxation, serves as the major initiator and control point for plant cell enlargement. Two views of wall relaxation as a viscoelastic or a chemorheological process are compared and distinguished.

  19. Leaf hydraulic conductance varies with vein anatomy across Arabidopsis thaliana wild-type and leaf vein mutants.

    Science.gov (United States)

    Caringella, Marissa A; Bongers, Franca J; Sack, Lawren

    2015-12-01

    Leaf venation is diverse across plant species and has practical applications from paleobotany to modern agriculture. However, the impact of vein traits on plant performance has not yet been tested in a model system such as Arabidopsis thaliana. Previous studies analysed cotyledons of A. thaliana vein mutants and identified visible differences in their vein systems from the wild type (WT). We measured leaf hydraulic conductance (Kleaf ), vein traits, and xylem and mesophyll anatomy for A. thaliana WT (Col-0) and four vein mutants (dot3-111 and dot3-134, and cvp1-3 and cvp2-1). Mutant true leaves did not possess the qualitative venation anomalies previously shown in the cotyledons, but varied quantitatively in vein traits and leaf anatomy across genotypes. The WT had significantly higher mean Kleaf . Across all genotypes, there was a strong correlation of Kleaf with traits related to hydraulic conductance across the bundle sheath, as influenced by the number and radial diameter of bundle sheath cells and vein length per area. These findings support the hypothesis that vein traits influence Kleaf , indicating the usefulness of this mutant system for testing theory that was primarily established comparatively across species, and supports a strong role for the bundle sheath in influencing Kleaf .

  20. Geologically based model of heterogeneous hydraulic conductivity in an alluvial setting

    Science.gov (United States)

    Fogg, Graham E.; Noyes, Charles D.; Carle, Steven F.

    Information on sediment texture and spatial continuity are inherent to sedimentary depositional facies descriptions, which are therefore potentially good predictors of spatially varying hydraulic conductivity (K). Analysis of complex alluvial heterogeneity in Livermore Valley, California, USA, using relatively abundant core descriptions and field pumping-test data, demonstrates a depositional-facies approach to characterization of subsurface heterogeneity. Conventional textural classifications of the core show a poor correlation with K; however, further refinement of the textural classifications into channel, levee, debris-flow, and flood-plain depositional facies reveals a systematic framework for spatial modeling of K. This geologic framework shows that most of the system is composed of very low-K flood-plain materials, and that the K measurements predominantly represent the other, higher-K facies. Joint interpretation of both the K and geologic data shows that spatial distribution of K in this system could not be adequately modeled without geologic data and analysis. Furthermore, it appears that K should not be assumed to be log-normally distributed, except perhaps within each facies. Markov chain modeling of transition probability, representing spatial correlation within and among the facies, captures the relevant geologic features while highlighting a new approach for statistical characterization of hydrofacies spatial variability. The presence of fining-upward facies sequences, cross correlation between facies, as well as other geologic attributes captured by the Markov chains provoke questions about the suitability of conventional geostatistical approaches based on variograms or covariances for modeling geologic heterogeneity. Résumé Les informations sur la texture des sédiments et leur continuité spatiale font partie des descriptions de faciès sédimentaires de dépôt. Par conséquent, ces descriptions sont d'excellents prédicteurs potentiels des

  1. Laser X-ray Conversion and Electron Thermal Conductivity*

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The influence of electron thermal conductivity on the laser x-ray conversion in the coupling of 3ωo laser with Au plane target has been investigated by using a non-LTE radiation hydrodynamic code. The non-local electron thermal conductivity is introduced and compared with the other two kinds of the flux-limited Spitzer-Harm description. The results show that the non-local thermal conductivity causes the increase of the laser x-ray conversion efficiency andimportant changes of the plasma state and coupling feature

  2. Pure-oxygen radiative shocks with electron thermal conduction

    Science.gov (United States)

    Borkowski, Kazimierz J.; Shull, J. Michael

    1990-01-01

    Steady state radiative shock models in gas composed entirely of oxygen are calculated with the purpose of explaining observations of fast-moving knots in Cas A and other oxygen-rich SNRs. Models with electron thermal conduction differ significantly from models in which conduction is neglected. Conduction reduces postshock electron temperatures by a factor of 7-10 and flattens temperature gradients. The O III ion, whose forbidden emission usually dominates the observed spectra, is present over a wide range of shock velocities, from 100 to 170 km/s. The electron temperature in the O III forbidden line formation region is 30,000 K, in agreement with the 20,000 K derived from observations. All models with conduction have extensive warm (T above 4000 K) photoionization zones, which provides better agreement with observed optical O I line strengths.

  3. Electronic Conductivity of Vanadium-Tellurite Glass-Ceramics

    DEFF Research Database (Denmark)

    Kjeldsen, Jonas; Yue, Yuanzheng; Bragatto, Caio B.

    2013-01-01

    In this paper, we investigate the electronic conductivity of 2TeO2-V2O5 glass-ceramics with crystallinity ranging from 0 to 100 wt.%, i.e., from entirely amorphous to completely crystalline. The glass is prepared by the melt quenching technique, and the crystal is prepared by subsequent heat trea...... as percolation theory. This work implies that, based on its electronic conductivity, vitreous 2TeO2-V2O5 is more suitable as a cathode material in secondary batteries compared to a 2TeO2-V2O5 glass-ceramic.......In this paper, we investigate the electronic conductivity of 2TeO2-V2O5 glass-ceramics with crystallinity ranging from 0 to 100 wt.%, i.e., from entirely amorphous to completely crystalline. The glass is prepared by the melt quenching technique, and the crystal is prepared by subsequent heat...... treatment thereof. Glass-ceramics are prepared by mixing glass and crystal powder, followed by a sintering procedure. Activation energies for electronic conduction in the glass and in the crystal are determined by fitting the Mott-Austin equation to the electronic conductivity data obtained by impedance...

  4. Influence of temperature and hydraulic conductivity of soil on electrokinetic decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Gye-Nam; Kim, Seung-Soo; Jeong, Jung-Whan; Choi, Jong-Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    The electrokinetic process holds great promise for the decontamination of contaminated soil because it has a high removal efficiency and is time-effective for low permeability. Electrokinetic decontamination can be used to treat soil contaminated with inorganic species and radionuclides. The main mechanisms of a contaminant's movement in an electrical field involved in electrokinetic technology are the electro-migration of the ionic species and electro-osmosis. Electro-migration probably contributes significantly to the removal of contaminants, especially at high concentrations of ionic contaminants and/or a high hydraulic permeability of soil. The cathode reaction should be depolarized to avoid the generation of hydroxides and their transport in soil. The selected liquid, also known as a purging reagent, should induce favorable pH conditions in soil, and/or interact with the incorporated heavy metals so that these heavy metals are removed from the soil. The removal efficiencies of uranium from contaminated soil in manufactured laboratory electrokinetic decontamination equipment were proportional to the elapsed time. The removal efficiencies of uranium for 2 days were 77-87%. In addition, the removal efficiencies according to the elapsed time after 2 days were reduced. When 75, 80, and 85℃ electrolyte temperatures in the cathode chamber were applied, the time required for the removal efficiency of uranium to reach 92% was 6, 5 and 4 days.

  5. [Seasonal differences in the leaf hydraulic conductance of mature Acacia mangium in response to its leaf water use and photosynthesis].

    Science.gov (United States)

    Zhao, Ping; Sun, Gu-Chou; Ni, Guang-Yan; Zeng, Xiao-Ping

    2013-01-01

    In this study, measurements were made on the leaf water potential (psi1), stomatal conductance (g(s)), transpiration rate, leaf area index, and sapwood area of mature Acacia mangium, aimed to understand the relationships of the leaf hydraulic conductance (K1) with the leaf water use and photosynthetic characteristics of the A. mangium in wet season (May) and dry season (November). The ratio of sapwood area to leaf area (A(sp)/A(cl)) of the larger trees with an average height of 20 m and a diameter at breast height (DBH) of 0.26 m was 8.5% higher than that of the smaller trees with an average height of 14.5 m and a DBH of 0.19 m, suggesting that the larger trees had a higher water flux in their leaf xylem, which facilitated the water use of canopy leaf. The analysis on the vulnerability curve of the xylem showed that when the K1 decreased by 50%, the psi1 in wet season and dry season was -1.41 and -1.55 MPa, respectively, and the vulnerability of the xylem cavitation was higher in dry season than in wet season. The K1 peak value in wet season and dry season was 5.5 and 4.5 mmol x m(-2) x s(-1) x MPa(-1), and the maximum transpiration rate (T(r max)) was 3.6 and 1.8 mmol x m(-2) x s(-1), respectively. Both the K1 and T(r max), were obviously higher in wet season than in dry season. Within a day, the K1 and T(r), fluctuated many times, reflecting the reciprocated cycle of the xylem cavitation and refilling. The leaf stomatal closure occurred when the K1 declined over 50% or the psi1 reached -1.6 MPa. The g(s) would be maintained at a high level till the K1 declined over 50%. The correlation between the hydraulic conductance and photosynthetic rate was more significant in dry season than in wet season. The loss of leaf hydraulic conductance induced by seasonal change could be the causes of the decrease of T(r) and CO2 gas exchange.

  6. Recent advances of conductive nanocomposites in printed and flexible electronics

    Science.gov (United States)

    Khan, Saleem; Lorenzelli, Leandro

    2017-08-01

    Conductive nanocomposites have emerged as significant smart engineered materials for realizing flexible electronics on diverse substrates in recent years. Conductive nanocomposites are comprised of conductive fillers mixed with polymeric elastomer (e.g. polydimethylsiloxane). The possibility to tune electrical as well as mechanical properties of nanocomposites makes them suitable for a wide spectrum of applications including sensors and electronics on non-planar and stretchable surfaces. A number of conductive nanofillers and manufacturing technologies have been developed to meet the diverse requirements of various applications. Considering the substantial contribution of conductive nanocomposites, it is opportune time to review the potentials of various nanofillers, their synthesis, processing methodologies and challenges associated to them. This paper reviews conductive nanocomposites, especially in context with their use in the development of electronic components and the sensors exploiting the piezoresistive behavior. The paper is structured around the nanocomposites related studies aiming to develop various building blocks of flexible electronic skin systems such as pressure, touch, strain and temperature sensors as well as stretchable interconnects. Besides this, the use of nanocomposites in other stimulating industrial and biomedical applications has also been explored briefly.

  7. Estimating the saturated soil hydraulic conductivity by the near steady-state phase of a beerkan infiltration run

    Science.gov (United States)

    Di Prima, Simone; Bagarello, Vincenzo; Iovino, Massimo

    2017-04-01

    Simple infiltration experiments carried out in the field allow an easy and inexpensive way of characterizing soil hydraulic behavior, maintaining the functional connection of the sampled soil volume with the surrounding soil. The beerkan method consists of a three-dimensional (3D) infiltration experiment at zero pressure head (Haverkamp et al., 1996). It uses a simple annular ring inserted to a depth of about 0.01 m to avoid lateral loss of the ponded water. Soil disturbance is minimized by the limited ring insertion depth. Infiltration time of small volumes of water repeatedly poured on the confined soil are measured to determine the cumulative infiltration. Different algorithms based on this methodology (the so-called BEST family of algorithms) were developed for the determination of soil hydraulic characteristic parameters (Bagarello et al., 2014a; Lassabatere et al., 2006; Yilmaz et al., 2010). Recently, Bagarello et al. (2014b) developed a Simplified method based on a Beerkan Infiltration run (SBI method) to determine saturated soil hydraulic conductivity, Ks, by only the transient phase of a beerkan infiltration run and an estimate of the α* parameter, expressing the relative importance of gravity and capillary forces during an infiltration process (Reynolds and Elrick, 1990). However, several problems yet arise with the existing BEST-algorithms and the SBI method, including (i) the need of supplementary field and laboratory measurements (Bagarello et al., 2013); (ii) the difficulty to detect a linear relationship between I / √t and √t in the early stage of the infiltration process (Bagarello et al., 2014b); (iii) estimation of negative Ks values for hydrophobic soils (Di Prima et al., 2016). In this investigation, a new Simplified method based on the analysis of the Steady-state Beerkan Infiltration run (SSBI method) was proposed and tested. In particular, analytical data were generated to simulate beerkan infiltration experiments for six contrasting

  8. Conduction mechanism studies on electron transfer of disordered system

    Institute of Scientific and Technical Information of China (English)

    徐慧; 宋祎璞; 李新梅

    2002-01-01

    Using the negative eigenvalue theory and the infinite order perturbation theory, a new method was developed to solve the eigenvectors of disordered systems. The result shows that eigenvectors change from the extended state to the localized state with the increase of the site points and the disordered degree of the system. When electric field is exerted, the electrons transfer from one localized state to another one. The conductivity is induced by the electron transfer. The authors derive the formula of electron conductivity and find the electron hops between localized states whose energies are close to each other, whereas localized positions differ from each other greatly. At low temperature the disordered system has the character of the negative differential dependence of resistivity and temperature.

  9. Kinetics of recovery of leaf hydraulic conductance and vein functionality from cavitation-induced embolism in sunflower.

    Science.gov (United States)

    Trifilò, Patrizia; Gascó, Antonio; Raimondo, Fabio; Nardini, Andrea; Salleo, Sebastiano

    2003-10-01

    The kinetics of leaf vein recovery from cavitation-induced embolism was studied in plants of sunflower cv. Margot, together with the impact of vein embolism on the overall leaf hydraulic conductance (Kleaf). During the air-dehydration of leaves to leaf water potentials (Psi L) of -1.25 MPa, Kleaf was found to decrease by about 46% with respect to values recorded in well-hydrated leaves. When leaves, previously dehydrated to Psi L= -1.1 MPa (corresponding to the turgor loss point), were put in contact with water, Kleaf recovered completely in 10 min and so did leaf water potential. Functional vein density was estimated in both dehydrating and rehydrating leaves in terms of total length of red-stained veins infiltrated with a Phloxine B solution per unit leaf surface area. Veins were found to embolize (unstained) with kinetics showing a linear relationship with Kleaf so that about a 70% loss of functional veins corresponded with a Kleaf loss of 46%. Cavitated veins recovered from embolism within 10 min from the beginning of leaf rehydration. These data indicate that: (a) leaves of sunflower underwent substantial vein embolism during dehydration; (b) vein embolism and leaf hydraulic efficiency apparently recovered from dehydration completely and rapidly upon rehydration; (c) vein refilling occurred while conduits were still at more negative xylem pressures than those required for spontaneous bubble dissolution on the basis of Henry's law. The possible consistent contribution of vital mechanisms for vein refilling is discussed.

  10. Comparison of Three Methods for Determination of Root Hydraulic Conductivity of Maize (Zea mays L.) Root System

    Institute of Scientific and Technical Information of China (English)

    LI Qing-ming; LIU Bin-bin

    2010-01-01

    Three techniques of root pressure probe,pressure chamber and high pressure flow meter were used to measure the hydraulic conduetivities (Lp,) of whole root systems of young maize (Zea mays L.) seedlings grown hydroponically under either drought or normal water conditions.Compared to normal water conditions,drought stress simulated by polyethylene glycol 6 000 (osmotic potential=-0.2 MPa) reduced Lp,in the root system by over 50%.It indicated that water permeability in the roots decreased significantly when plants suffered from water shortages.Moreover,there was no significant difference (P<0.05) on the Lpr values in the root systems developed under a given water stress regime among the three techniques used.Therefore,all three methods are acceptable to study the hydraulic conductivity of maize seedling root systems.We have also highlighted some of the technical limitations of each method.It can be inferred that the root pressure probe is preferable for young maize seedlings because it is subtle and has the additional ability to determine solute transport properties,but the method is time consuming.Other advantages and disadvantages of each technique are discussed in order to acquaint researchers with basic information that could contribute to their choice of an appropriate technique for future studies.

  11. Quasi-ballistic Electronic Thermal Conduction in Metal Inverse Opals.

    Science.gov (United States)

    Barako, Michael T; Sood, Aditya; Zhang, Chi; Wang, Junjie; Kodama, Takashi; Asheghi, Mehdi; Zheng, Xiaolin; Braun, Paul V; Goodson, Kenneth E

    2016-04-13

    Porous metals are used in interfacial transport applications that leverage the combination of electrical and/or thermal conductivity and the large available surface area. As nanomaterials push toward smaller pore sizes to increase the total surface area and reduce diffusion length scales, electron conduction within the metal scaffold becomes suppressed due to increased surface scattering. Here we observe the transition from diffusive to quasi-ballistic thermal conduction using metal inverse opals (IOs), which are metal films that contain a periodic arrangement of interconnected spherical pores. As the material dimensions are reduced from ∼230 nm to ∼23 nm, the thermal conductivity of copper IOs is reduced by more than 57% due to the increase in surface scattering. In contrast, nickel IOs exhibit diffusive-like conduction and have a constant thermal conductivity over this size regime. The quasi-ballistic nature of electron transport at these length scales is modeled considering the inverse opal geometry, surface scattering, and grain boundaries. Understanding the characteristics of electron conduction at the nanoscale is essential to minimizing the total resistance of porous metals for interfacial transport applications, such as the total electrical resistance of battery electrodes and the total thermal resistance of microscale heat exchangers.

  12. Use of NMR logging to obtain estimates of hydraulic conductivity in the High Plains aquifer, Nebraska, USA

    Science.gov (United States)

    Dlubac, Katherine; Knight, Rosemary; Song, Yi-Qiao; Bachman, Nate; Grau, Ben; Cannia, Jim; Williams, John

    2013-01-01

    Hydraulic conductivity (K) is one of the most important parameters of interest in groundwater applications because it quantifies the ease with which water can flow through an aquifer material. Hydraulic conductivity is typically measured by conducting aquifer tests or wellbore flow (WBF) logging. Of interest in our research is the use of proton nuclear magnetic resonance (NMR) logging to obtain information about water-filled porosity and pore space geometry, the combination of which can be used to estimate K. In this study, we acquired a suite of advanced geophysical logs, aquifer tests, WBF logs, and sidewall cores at the field site in Lexington, Nebraska, which is underlain by the High Plains aquifer. We first used two empirical equations developed for petroleum applications to predict K from NMR logging data: the Schlumberger Doll Research equation (KSDR) and the Timur-Coates equation (KT-C), with the standard empirical constants determined for consolidated materials. We upscaled our NMR-derived K estimates to the scale of the WBF-logging K(KWBF-logging) estimates for comparison. All the upscaled KT-C estimates were within an order of magnitude of KWBF-logging and all of the upscaled KSDR estimates were within 2 orders of magnitude of KWBF-logging. We optimized the fit between the upscaled NMR-derived K and KWBF-logging estimates to determine a set of site-specific empirical constants for the unconsolidated materials at our field site. We conclude that reliable estimates of K can be obtained from NMR logging data, thus providing an alternate method for obtaining estimates of K at high levels of vertical resolution.

  13. Comparison of laboratory, in situ, and rock mass measurements of the hydraulic conductivity of metamorphic rock at the Savannah River Plant near Aiken, South Carolina

    Energy Technology Data Exchange (ETDEWEB)

    Marine, I W

    1980-01-01

    In situ testing of exploratory wells in metamorphic rock indicates that two types of fracturing occur in the rock mass. Rock containing small openings that permit only extremely slow movement of water is termed virtually impermeable rock. Rock containing openings of sufficient size to permit transmission of water at a significantly faster rate is termed hydraulically transmissive rock. Laboratory methods are unsuitable for measuring hydraulic conductivity in hydraulically transmissive rock; however, for the virtually impermeable rock, values comparable to the in situ tests are obtained. The hydraulic conductivity of the rock mass over a large region is calculated by using the hydraulic gradient, porosity, and regional velocity. This velocity is determined by dividing the inferred travel distance by the age of water which is determined by the helium content of the water. This rock mass hydraulic conductivity value is between the values measured for the two types of fractures, but is closer to the measured value for the virtually impermeable rock. This relationship is attributed to the control of the regional flow rate by the virtually impermeable rock where the discrete fractures do not form a continuous open connection through the entire rock mass. Thus, laboratory methods of measuring permeability in metamorphic rock are of value if they are properly applied.

  14. Comparison of Laboratory, in Situ, and Rock Mass Measurements of the Hydraulic Conductivity of Metamorphic Rock at the Savannah River Plant Near Aiken, South Carolina

    Science.gov (United States)

    Marine, I. Wendell

    1981-06-01

    In situ testing of exploratory wells in metamorphic rock indicates that two types of fracturing occur in the rock mass. Rock containing small openings that permit only extremely slow movement of water is termed virtually impermeable rock. Rock containing openings of sufficient size to permit transmission of water at a significantly faster rate is termed hydraulically transmissive rock. Laboratory methods are unsuitable for measuring hydraulic conductivity in hydraulically transmissive rock; however, for the virtually impermeable rock, values comparable to those of the in situ tests are obtained. The hydraulic conductivity of the rock mass over a large region is calculated by using the hydraulic gradient, porosity, and regional velocity. This velocity is determined by dividing the inferred travel distance by the age of water, which is determined by the helium content of the water. This rock mass hydraulic conductivity value is between the values measured for the two types of fractures but is closer to the measured value for the virtually impermeable rock. This relationship is attributed to the control of the regional flow rate by the virtually impermeable rock where the discrete fractures do not form a continuous open connection through the entire rock mass. Thus laboratory methods of measuring permeability in metamorphic rock are of value if they are properly applied.

  15. Agricultural use of soil, consequences in soil organic matter and hydraulic conductivity compared with natural vegetation in central Spain

    Science.gov (United States)

    Vega, Verónica; Carral, Pilar; Alvarez, Ana Maria; Marques, Maria Jose

    2014-05-01

    When ecosystems are under pressure due to high temperatures and water scarcity, the use of land for agriculture can be a handicap for soil and water conservation. The interactions between plants and soils are site-specific. This study provides information about the influence of the preence vs. The absence of vegetation on soil in a semi-arid area of the sout-east of Madrid (Spain, in the Tagus River basin. In this area soil materials are developed over a calcareous-evaporitic lithology. Soils can be classified as Calcisols, having horizons of accumulation with powdered limestone and irregular nodules of calcium carbonate. They can be defined as Haplic Cambisols and Leptic Calcisols (WRB 2006-FAO). The area is mainly used for rainfed agriculture, olive groves, vineyards and cereals. There are some patches of bushes (Quercus sp.) and grasses (Stipa tenacissima L.) although only found on the top of the hills. This study analyses the differences found in soils having three different covers: Quercus coccifera, Stipa tenacissima and lack of vegetation. This last condition was found in the areas between cultivated olive trees. Soil organic matter, porosity and hydraulic conductivity are key properties of soil to understand its ability to adapt to climate or land use changes. In order to measure the influence of different soil covers, four replicates of soil were sampled in each condition at two soil depth, (0-10 cm and 10-20 cm). Hydraulic conductivity was measured in each soil condition and replicate using a Mini-disk® infiltrometer. There were no differences between the two depths sampled. Similarly, there were no changes in electric conductivity (average 0.1±0.03 dS m-1); pH (8.7±0.2) or calcium carbonate content (43±20 %). Nevertheless, significant differences (p>0.001) were found in soil organic matter. The maximum was found in soils under Quercus (4.7±0.5 %), followed by Stipa (2.2±1.1 %). The soil without vegetation in the areas between olive trees had only 0

  16. Estimation of hydraulic parameters from an unconfined aquifer test conducted in a glacial outwash deposit, Cape Cod, Massachusetts

    Science.gov (United States)

    Moench, A.F.; Garabedian, Stephen P.; LeBlanc, Denis R.

    2000-01-01

    An aquifer test conducted in a sand and gravel, glacial outwash deposit on Cape Cod, Massachusetts was analyzed by means of a model for flow to a partially penetrating well in a homogeneous, anisotropic unconfined aquifer. The model is designed to account for all significant mechanisms expected to influence drawdown in observation piezometers and in the pumped well. In addition to the usual fluid-flow and storage processes, additional processes include effects of storage in the pumped well, storage in observation piezometers, effects of skin at the pumped-well screen, and effects of drainage from the zone above the water table. The aquifer was pumped at a rate of 320 gallons per minute for 72-hours and drawdown measurements were made in the pumped well and in 20 piezometers located at various distances from the pumped well and depths below the land surface. To facilitate the analysis, an automatic parameter estimation algorithm was used to obtain relevant unconfined aquifer parameters, including the saturated thickness and a set of empirical parameters that relate to gradual drainage from the unsaturated zone. Drainage from the unsaturated zone is treated in this paper as a finite series of exponential terms, each of which contains one empirical parameter that is to be determined. It was necessary to account for effects of gradual drainage from the unsaturated zone to obtain satisfactory agreement between measured and simulated drawdown, particularly in piezometers located near the water table. The commonly used assumption of instantaneous drainage from the unsaturated zone gives rise to large discrepancies between measured and predicted drawdown in the intermediate-time range and can result in inaccurate estimates of aquifer parameters when automatic parameter estimation procedures are used. The values of the estimated hydraulic parameters are consistent with estimates from prior studies and from what is known about the aquifer at the site. Effects of

  17. Changes in hydraulic conductance cause the difference in growth response to short-term salt stress between salt-tolerant and -sensitive black gram (Vigna mungo) varieties.

    Science.gov (United States)

    Win, Khin Thuzar; Oo, Aung Zaw; Ookawa, Taiichiro; Kanekatsu, Motoki; Hirasawa, Tadashii

    2016-04-01

    Black gram (Vigna mungo) is an important crop in Asia, However, most black gram varieties are salt-sensitive. The causes of varietal differences in salt-induced growth reduction between two black gram varieties, 'U-Taung-2' (salt-tolerant; BT) and 'Mut Pe Khaing To' (salt-sensitive; BS), were examined the potential for the first step toward the genetic improvement of salt tolerance. Seedlings grown in vermiculite irrigated with full-strength Hoagland solution were treated with 0mM NaCl (control) or 225 mM NaCl for up to 10 days. In the 225 mM NaCl treatment, plant growth rate, net assimilation rate, mean leaf area, leaf water potential, and leaf photosynthesis were reduced more in BS than in BT plants. Leaf water potential was closely related to leaf photosynthesis, net assimilation rate, and increase in leaf area. In response to salinity stress, hydraulic conductance of the root, stem, and petiole decreased more strongly in BS than in BT plants. The reduction in stem and petiole hydraulic conductance was caused by cavitation, whereas the reduction in root hydraulic conductance in BS plants was caused by a reduction in root surface area and hydraulic conductivity. We conclude that the different reduction in hydraulic conductance is a cause of the differences in the growth response between the two black gram varieties under short-term salt stress.

  18. Feedback from uncertainties propagation research projects conducted in different hydraulic fields: outcomes for engineering projects and nuclear safety assessment.

    Science.gov (United States)

    Bacchi, Vito; Duluc, Claire-Marie; Bertrand, Nathalie; Bardet, Lise

    2017-04-01

    In recent years, in the context of hydraulic risk assessment, much effort has been put into the development of sophisticated numerical model systems able reproducing surface flow field. These numerical models are based on a deterministic approach and the results are presented in terms of measurable quantities (water depths, flow velocities, etc…). However, the modelling of surface flows involves numerous uncertainties associated both to the numerical structure of the model, to the knowledge of the physical parameters which force the system and to the randomness inherent to natural phenomena. As a consequence, dealing with uncertainties can be a difficult task for both modelers and decision-makers [Ioss, 2011]. In the context of nuclear safety, IRSN assesses studies conducted by operators for different reference flood situations (local rain, small or large watershed flooding, sea levels, etc…), that are defined in the guide ASN N°13 [ASN, 2013]. The guide provides some recommendations to deal with uncertainties, by proposing a specific conservative approach to cover hydraulic modelling uncertainties. Depending of the situation, the influencing parameter might be the Strickler coefficient, levee behavior, simplified topographic assumptions, etc. Obviously, identifying the most influencing parameter and giving it a penalizing value is challenging and usually questionable. In this context, IRSN conducted cooperative (Compagnie Nationale du Rhone, I-CiTy laboratory of Polytech'Nice, Atomic Energy Commission, Bureau de Recherches Géologiques et Minières) research activities since 2011 in order to investigate feasibility and benefits of Uncertainties Analysis (UA) and Global Sensitivity Analysis (GSA) when applied to hydraulic modelling. A specific methodology was tested by using the computational environment Promethee, developed by IRSN, which allows carrying out uncertainties propagation study. This methodology was applied with various numerical models and in

  19. Dynamic effects of wet-dry cycles and crust formation on the saturated hydraulic conductivity of surface soils in the constructed Hühnerwasser ("Chicken Creek") catchment

    Science.gov (United States)

    Hinz, Christoph; Schümberg, Sabine; Kubitz, Anita; Frank, Franzi; Cheng, Zhang; Nanu Frechen, Tobias; Pohle, Ina

    2016-04-01

    Highly disturbed soils and substrates used in land rehabilitation undergo rapid changes after the first wetting events which in turn can lead to ecosystem degradation. Such changes were detected during the early development of the constructed Hühnerwasser ("Chicken Creek") catchment in Lusatia, Germany. Surface substrates consisting of quaternary sandy sediments formed surface seals during the first rainfall events leading to reduced infiltration and substantially increased surface runoff. Subsequently biological soil crusts formed and stabilised the surface. The aim of this study is to investigate the factors that cause the hydraulic conductivity to decrease using undisturbed and disturbed soil samples. Based on the hypothesis that physical and biological crusts lower the hydraulic conductivity, the first set of experiments with undisturbed soil cores from the Hühnerwasser catchment were carried out to measure the saturated hydraulic conductivity using the constant head method. Measurements were done with intact cores and repeated after the surface crust was removed. As the quaternary glacial sediments tend to display hard setting behaviour, we further hypothesised that the mobilisation of fine particles within the cores lead to pore clogging and that wet-dry cycles will therefore decrease hydraulic conductivity. A second set of experiments using the same methodology consisted of five repeated measurements of hydraulic conductivity after each drying cycle. These measurements were done with undisturbed core samples as well as repacked cores in order to assess how dry packing affects the dynamics of the hydraulic conductivity somewhat similar to the situation during the first wetting after completion of the catchment construction. For all experiments, the temporal evolution of hydraulic conductivity was measured and the turbidity of the effluent was recorded. The results clearly demonstrated that the substrate is highly unstable. The first set of experiments

  20. Electronic Conductivity of Polypyrrole−Dodecyl Benzene Sulfonate Complexes

    DEFF Research Database (Denmark)

    West, Keld; Bay, Lasse; Nielsen, Martin Meedom

    2004-01-01

    The electronic conductivity of the electroactive polymer polypyrrole-dodecyl benzene sulfonate (PPy-DBS) has been characterized as function of the redox level. The polymer was synthesized with different isomers of the dopant anions: the common mixed DBS tenside and three well-defined synthetic...

  1. Two-temperature radiative shocks with electron thermal conduction

    Science.gov (United States)

    Borkowski, Kazimierz J.; Shull, J. Michael; Mckee, Christopher F.

    1989-01-01

    The influence of electron thermal conduction on radiative shock structure is studied for both one- and two-temperature plasmas. The dimensionless ratio of the conductive length to the cooling length determines whether or not conduction is important, and shock jump conditions with conduction are established for a collisionless shock front. Approximate solutions are obtained, with the assumptions that the ionization state of the gas is constant and the cooling rate is a function of temperature alone. In the absence of magnetic fields, these solutions indicate that conduction noticeably influences normal-abundance interstellar shocks with velocities 50-100 km/s and dramatically affects metal-dominated shocks over a wide range of shock velocities.

  2. Measurement of leaf hydraulic conductance and stomatal conductance and their responses to irradiance and dehydration using the Evaporative Flux Method (EFM).

    Science.gov (United States)

    Sack, Lawren; Scoffoni, Christine

    2012-12-31

    Water is a key resource, and the plant water transport system sets limits on maximum growth and drought tolerance. When plants open their stomata to achieve a high stomatal conductance (gs) to capture CO2 for photosynthesis, water is lost by transpiration(1,2). Water evaporating from the airspaces is replaced from cell walls, in turn drawing water from the xylem of leaf veins, in turn drawing from xylem in the stems and roots. As water is pulled through the system, it experiences hydraulic resistance, creating tension throughout the system and a low leaf water potential (Ψ(leaf)). The leaf itself is a critical bottleneck in the whole plant system, accounting for on average 30% of the plant hydraulic resistance(3). Leaf hydraulic conductance (K(leaf) = 1/ leaf hydraulic resistance) is the ratio of the water flow rate to the water potential gradient across the leaf, and summarizes the behavior of a complex system: water moves through the petiole and through several orders of veins, exits into the bundle sheath and passes through or around mesophyll cells before evaporating into the airspace and being transpired from the stomata. K(leaf) is of strong interest as an important physiological trait to compare species, quantifying the effectiveness of the leaf structure and physiology for water transport, and a key variable to investigate for its relationship to variation in structure (e.g., in leaf venation architecture) and its impacts on photosynthetic gas exchange. Further, K(leaf) responds strongly to the internal and external leaf environment(3). K(leaf) can increase dramatically with irradiance apparently due to changes in the expression and activation of aquaporins, the proteins involved in water transport through membranes(4), and K(leaf) declines strongly during drought, due to cavitation and/or collapse of xylem conduits, and/or loss of permeability in the extra-xylem tissues due to mesophyll and bundle sheath cell shrinkage or aquaporin deactivation(5

  3. An accurate way to determine the ionic conductivity of mixed ionic-electronic conducting (MIEC) ceramics

    NARCIS (Netherlands)

    Chen, W.; Nauels, N.; Bouwmeester, H.J.M.; Nijmeijer, A.; Winnubst, A.J.A.

    2015-01-01

    Measuring oxygen transport through dense, mixed ion–electron conducting, ceramic membranes is usually performed in a lab-scale permeationset-up where feed and sweep gas are directly flushed to the membrane surface. Due to concentration gradients, the oxygen partial pressure PO2 measured at the outle

  4. Saturated hydraulic conductivity model computed from bimodal water retention curves for a range of New Zealand soils

    Directory of Open Access Journals (Sweden)

    J. A. P. Pollacco

    2017-06-01

    Full Text Available Descriptions of soil hydraulic properties, such as the soil moisture retention curve, θ(h, and saturated hydraulic conductivities, Ks, are a prerequisite for hydrological models. Since the measurement of Ks is expensive, it is frequently derived from statistical pedotransfer functions (PTFs. Because it is usually more difficult to describe Ks than θ(h from pedotransfer functions, Pollacco et al. (2013 developed a physical unimodal model to compute Ks solely from hydraulic parameters derived from the Kosugi θ(h. This unimodal Ks model, which is based on a unimodal Kosugi soil pore-size distribution, was developed by combining the approach of Hagen–Poiseuille with Darcy's law and by introducing three tortuosity parameters. We report here on (1 the suitability of the Pollacco unimodal Ks model to predict Ks for a range of New Zealand soils from the New Zealand soil database (S-map and (2 further adaptations to this model to adapt it to dual-porosity structured soils by computing the soil water flux through a continuous function of an improved bimodal pore-size distribution. The improved bimodal Ks model was tested with a New Zealand data set derived from historical measurements of Ks and θ(h for a range of soils derived from sandstone and siltstone. The Ks data were collected using a small core size of 10 cm diameter, causing large uncertainty in replicate measurements. Predictions of Ks were further improved by distinguishing topsoils from subsoil. Nevertheless, as expected, stratifying the data with soil texture only slightly improved the predictions of the physical Ks models because the Ks model is based on pore-size distribution and the calibrated parameters were obtained within the physically feasible range. The improvements made to the unimodal Ks model by using the new bimodal Ks model are modest when compared to the unimodal model, which is explained by the poor accuracy of measured total porosity. Nevertheless, the new bimodal

  5. Saturated hydraulic conductivity model computed from bimodal water retention curves for a range of New Zealand soils

    Science.gov (United States)

    Pollacco, Joseph Alexander Paul; Webb, Trevor; McNeill, Stephen; Hu, Wei; Carrick, Sam; Hewitt, Allan; Lilburne, Linda

    2017-06-01

    Descriptions of soil hydraulic properties, such as the soil moisture retention curve, θ(h), and saturated hydraulic conductivities, Ks, are a prerequisite for hydrological models. Since the measurement of Ks is expensive, it is frequently derived from statistical pedotransfer functions (PTFs). Because it is usually more difficult to describe Ks than θ(h) from pedotransfer functions, Pollacco et al. (2013) developed a physical unimodal model to compute Ks solely from hydraulic parameters derived from the Kosugi θ(h). This unimodal Ks model, which is based on a unimodal Kosugi soil pore-size distribution, was developed by combining the approach of Hagen-Poiseuille with Darcy's law and by introducing three tortuosity parameters. We report here on (1) the suitability of the Pollacco unimodal Ks model to predict Ks for a range of New Zealand soils from the New Zealand soil database (S-map) and (2) further adaptations to this model to adapt it to dual-porosity structured soils by computing the soil water flux through a continuous function of an improved bimodal pore-size distribution. The improved bimodal Ks model was tested with a New Zealand data set derived from historical measurements of Ks and θ(h) for a range of soils derived from sandstone and siltstone. The Ks data were collected using a small core size of 10 cm diameter, causing large uncertainty in replicate measurements. Predictions of Ks were further improved by distinguishing topsoils from subsoil. Nevertheless, as expected, stratifying the data with soil texture only slightly improved the predictions of the physical Ks models because the Ks model is based on pore-size distribution and the calibrated parameters were obtained within the physically feasible range. The improvements made to the unimodal Ks model by using the new bimodal Ks model are modest when compared to the unimodal model, which is explained by the poor accuracy of measured total porosity. Nevertheless, the new bimodal model provides an

  6. Molecular Dynamics Simulations of Shocks Including Electronic Heat Conduction and Electron-Phonon Coupling

    Science.gov (United States)

    Ivanov, Dmitriy S.; Zhigilei, Leonid V.; Bringa, Eduardo M.; De Koning, Maurice; Remington, Bruce A.; Caturla, Maria Jose; Pollaine, Stephen M.

    2004-07-01

    Shocks are often simulated using the classical molecular dynamics (MD) method in which the electrons are not included explicitly and the interatomic interaction is described by an effective potential. As a result, the fast electronic heat conduction in metals and the coupling between the lattice vibrations and the electronic degrees of freedom can not be represented. Under conditions of steep temperature gradients that can form near the shock front, however, the electronic heat conduction can play an important part in redistribution of the thermal energy in the shocked target. We present the first atomistic simulation of a shock propagation including the electronic heat conduction and electron-phonon coupling. The computational model is based on the two-temperature model (TTM) that describes the time evolution of the lattice and electron temperatures by two coupled non-linear differential equations. In the combined TTM-MD method, MD substitutes the TTM equation for the lattice temperature. Simulations are performed with both MD and TTM-MD models for an EAM Al target shocked at 300 kbar. The target includes a tilt grain boundary, which provides a region where shock heating is more pronounced and, therefore, the effect of the electronic heat conduction is expected to be more important. We find that the differences between the predictions of the MD and TTM-MD simulations are significantly smaller as compared to the hydrodynamics calculations performed at similar conditions with and without electronic heat conduction.

  7. A safety vs efficiency trade-off identified in the hydraulic pathway of grass leaves is decoupled from photosynthesis, stomatal conductance and precipitation.

    Science.gov (United States)

    Ocheltree, Troy W; Nippert, Jesse B; Prasad, P V Vara

    2016-04-01

    A common theme in plant physiological research is the trade-off between stress tolerance and growth; an example of this trade-off at the tissue level is the safety vs efficiency hypothesis, which suggests that plants with the greatest resistance to hydraulic failure should have low maximum hydraulic conductance. Here, we quantified the leaf-level drought tolerance of nine C4 grasses as the leaf water potential at which plants lost 50% (P50 × RR ) of maximum leaf hydraulic conductance (Ksat ), and compared this trait with other leaf-level and whole-plant functions. We found a clear trade-off between Ksat and P50 × RR when Ksat was normalized by leaf area and mass (P = 0.05 and 0.01, respectively). However, no trade-off existed between P50 × RR and gas-exchange rates; rather, there was a positive relationship between P50 × RR and photosynthesis (P = 0.08). P50 × RR was not correlated with species distributions based on precipitation (P = 0.70), but was correlated with temperature during the wettest quarter of the year (P hydraulic system of grass leaves, which can be decoupled from other leaf-level functions. The unique physiology of C4 plants and adaptations to pulse-driven systems may provide mechanisms that could decouple hydraulic conductance from other plant functions.

  8. The effects of desensitizing agents on the hydraulic conductance of human dentin in vitro.

    Science.gov (United States)

    Greenhill, J D; Pashley, D H

    1981-03-01

    The hydrodynamic theory of dentin sensitivity states that a stimulus applied at the orifice of exposed dentinal tubules causes movement of tubular fluid which stimulates nerve receptors. The fluid should obey principles of fluid movement through capillary tubes. Any decrease in the functional radius of the dentinal tubules should greatly reduce the rate of fluid flow, thus reducing dentinal sensitivity. The purpose of this study was to evaluate the ability of agents that have been used previously for clinical dentin desensitization to reduce the rate of fluid flow through dentin in vitro. Dentin discs prepared from extracted human third molars were treated with 50% citric acid to remove debris from tubular orifices. After placing the discs in a split chamber device, the rate at which buffer solution could filter across the dentin under 240 cm of water pressure was measured. The occlusal side of the disc was then treated with an agent thought to desensitize dentin to determine if it reduced fluid flow rate. Discs that had more than a 50% reduction in flow rate were examined by scanning electron microscopy to determine if those agents that decreased fluid flow also partially occluded tubular orifices. This in vitro model provided a useful quantitative method for screening a host of preparations that have been used in the past to decrease dentin sensitivity.

  9. Does the soil's effective hydraulic conductivity adapt in order to obey the Maximum Entropy Production principle? A lab experiment

    Science.gov (United States)

    Westhoff, Martijn; Zehe, Erwin; Erpicum, Sébastien; Archambeau, Pierre; Pirotton, Michel; Dewals, Benjamin

    2015-04-01

    The Maximum Entropy Production (MEP) principle is a conjecture assuming that a medium is organized in such a way that maximum power is subtracted from a gradient driving a flux (with power being a flux times its driving gradient). This maximum power is also known as the Carnot limit. It has already been shown that the atmosphere operates close to this Carnot limit when it comes to heat transport from the Equator to the poles, or vertically, from the surface to the atmospheric boundary layer. To reach this state close to the Carnot limit, the effective thermal conductivity of the atmosphere is adapted by the creation of convection cells (e.g. wind). The aim of this study is to test if the soil's effective hydraulic conductivity also adapts itself in such a way that it operates close to the Carnot limit. The big difference between atmosphere and soil is the way of adaptation of its resistance. The soil's hydraulic conductivity is either changed by weathering processes, which is a very slow process, or by creation of preferential flow paths. In this study the latter process is simulated in a lab experiment, where we focus on the preferential flow paths created by piping. Piping is the process of backwards erosion of sand particles subject to a large pressure gradient. Since this is a relatively fast process, it is suitable for being tested in the lab. In the lab setup a horizontal sand bed connects two reservoirs that both drain freely at a level high enough to keep the sand bed always saturated. By adding water to only one reservoir, a horizontal pressure gradient is maintained. If the flow resistance is small, a large gradient develops, leading to the effect of piping. When pipes are being formed, the effective flow resistance decreases; the flow through the sand bed increases and the pressure gradient decreases. At a certain point, the flow velocity is small enough to stop the pipes from growing any further. In this steady state, the effective flow resistance of

  10. Mixed ionic and electronic conducting ceramic membranes for hydrocarbon processing

    Science.gov (United States)

    Van Calcar, Pamela; Mackay, Richard; Sammells, Anthony F.

    2002-01-01

    The invention relates to mixed phase materials for the preparation of catalytic membranes which exhibit ionic and electronic conduction and which exhibit improved mechanical strength compared to single phase ionic and electronic conducting materials. The mixed phase materials are useful for forming gas impermeable membranes either as dense ceramic membranes or as dense thin films coated onto porous substrates. The membranes and materials of this invention are useful in catalytic membrane reactors in a variety of applications including synthesis gas production. One or more crystalline second phases are present in the mixed phase material at a level sufficient to enhance the mechanical strength of the mixture to provide membranes for practical application in CMRs.

  11. Ab initio electronic structure and optical conductivity of bismuth tellurohalides

    CERN Document Server

    Schwalbe, Sebastian; Starke, Ronald; Schober, Giulio A H; Kortus, Jens

    2016-01-01

    We investigate the electronic structure, dielectric and optical properties of bismuth tellurohalides BiTeX (X = I, Cl, Br) by means of all-electron density functional theory. In particular, we present the ab initio conductivities and dielectric tensors calculated over a wide frequency range, and compare our results with the recent measurements by Akrap et al. , Makhnev et al. , and Rusinov et al. . We show how the low-frequency branch of the optical conductivity can be used to identify characteristic intra- and interband transitions between the Rashba spin-split bands in all three bismuth tellurohalides. We further calculate the refractive indices and dielectric constants, which in turn are systematically compared to previous predictions and measurements. We expect that our quantitative analysis will contribute to the general assessment of bulk Rashba materials for their potential use in spintronics devices.

  12. Electronic thermal conductivity in a superconducting vortex state

    Energy Technology Data Exchange (ETDEWEB)

    Adachi, H. [Department of Physics, Okayama University, Tsushima, Okayama 700-8530 (Japan)], E-mail: adachi@itp.phys.ethz.ch; Miranovic, P. [Department of Physics, University of Montenegro, Podgorica 81000 (Montenegro); Ichioka, M.; Machida, K. [Department of Physics, Okayama University, Tsushima, Okayama 700-8530 (Japan)

    2007-10-01

    The longitudinal component of the electronic thermal conductivity {kappa}{sub xx} in a superconducting vortex state is calculated as a function of magnetic field B. Calculations are performed by taking account of the spatial dependence of normal Green's function g, which was neglected in the previous studies using the Brandt-Pesch-Tewordt method. We discuss the possibility of using {kappa}{sub xx}(B) as a probe of the pair potential symmetry.

  13. Electronic thermal conductivity in a superconducting vortex state

    Science.gov (United States)

    Adachi, H.; Miranovic, P.; Ichioka, M.; Machida, K.

    2007-10-01

    The longitudinal component of the electronic thermal conductivity κxx in a superconducting vortex state is calculated as a function of magnetic field B. Calculations are performed by taking account of the spatial dependence of normal Green's function g, which was neglected in the previous studies using the Brandt-Pesch-Tewordt method. We discuss the possibility of using κxx(B) as a probe of the pair potential symmetry.

  14. Molecular Models for Conductance in Junctions and Electrochemical Electron Transfer

    Science.gov (United States)

    Mazinani, Shobeir Khezr Seddigh

    This thesis develops molecular models for electron transport in molecular junctions and intra-molecular electron transfer. The goal is to identify molecular descriptors that afford a substantial simplification of these electronic processes. First, the connection between static molecular polarizability and the molecular conductance is examined. A correlation emerges whereby the measured conductance of a tunneling junction decreases as a function of the calculated molecular polarizability for several systems, a result consistent with the idea of a molecule as a polarizable dielectric. A model based on a macroscopic extension of the Clausius-Mossotti equation to the molecular domain and Simmon's tunneling model is developed to explain this correlation. Despite the simplicity of the theory, it paves the way for further experimental, conceptual and theoretical developments in the use of molecular descriptors to describe both conductance and electron transfer. Second, the conductance of several biologically relevant, weakly bonded, hydrogen-bonded systems is systematically investigated. While there is no correlation between hydrogen bond strength and conductance, the results indicate a relation between the conductance and atomic polarizability of the hydrogen bond acceptor atom. The relevance of these results to electron transfer in biological systems is discussed. Hydrogen production and oxidation using catalysts inspired by hydrogenases provides a more sustainable alternative to the use of precious metals. To understand electrochemical and spectroscopic properties of a collection of Fe and Ni mimics of hydrogenases, high-level density functional theory calculations are described. The results, based on a detailed analysis of the energies, charges and molecular orbitals of these metal complexes, indicate the importance of geometric constraints imposed by the ligand on molecular properties such as acidity and electrocatalytic activity. Based on model calculations of

  15. High frequency conductivity of hot electrons in carbon nanotubes

    Science.gov (United States)

    Amekpewu, M.; Mensah, S. Y.; Musah, R.; Mensah, N. G.; Abukari, S. S.; Dompreh, K. A.

    2016-05-01

    High frequency conductivity of hot electrons in undoped single walled achiral Carbon Nanotubes (CNTs) under the influence of ac-dc driven fields was considered. We investigated semi-classically Boltzmann's transport equation with and without the presence of the hot electrons' source by deriving the current densities in CNTs. Plots of the normalized current density versus frequency of ac-field revealed an increase in both the minimum and maximum peaks of normalized current density at lower frequencies as a result of a strong injection of hot electrons. The applied ac-field plays a twofold role of suppressing the space-charge instability in CNTs and simultaneously pumping an energy for lower frequency generation and amplification of THz radiations. These have enormous promising applications in very different areas of science and technology.

  16. Use of Ground-water Temperature Patterns to Determine the Hydraulic Conductance of the Streambed Along the Middle Reaches of the Russian River, CA

    Science.gov (United States)

    Su, G. W.; Constantz, J.; Jasperse, J.; Seymour, D.

    2002-12-01

    Along the Russian River in Sonoma County, the alluvial aquifer is the preferred source of drinking water because sediments and other constituents in the river water would require additional treatment. From late spring to early winter, an inflatable dam is erected to raise the river stage and passively recharge the alluvial aquifer. The raised stage also permits diversion of river water to a series of recharge ponds located near the dam along the river. Improved understanding of stream exchanges with ground water is needed to better manage available water resources. Heat is used as a tracer of shallow ground-water movement for detailed hydraulic parameter estimation along the middle reaches of the river. Water-levels and ground-water temperatures were measured in a series of observations wells and compared to the river stage and surface-water temperatures. Hydraulic conductivities were predicted by optimizing simulated ground-water temperatures using VS2DHI, a heat and water transport model, to observed temperatures in the aquifer. These conductivity values will be used in a stream/ground-water model of this region being developed using MODFLOW. Temperature-based estimates of streambed conductance will be inserted in the STREAM package of the model to constrain this parameter. Although temperature-based predictions of hydraulic conductivity vary significantly along the reach, the results generally suggest that an anisotropy of 5 to 1 (horizontal to vertical) provides the best hydraulic conductivity matches for predicted versus observed ground-water temperatures.

  17. Studies of Electronic Conduction in Some Small Gallium Arsenic Based.

    Science.gov (United States)

    Whittington, Geoffrey

    Available from UMI in association with The British Library. Requires signed TDF. This thesis describes experimental investigations of the physics involved with low temperature electronic conduction in three different semiconductor systems. The research relies upon technological advances in fabrication of such semiconductor samples. The first work deals with the effects of quantum interference of electrons in some submicron size, heavily doped Gallium Arsenide wire samples. The interesting effect of aperiodic fluctuations in the magnetoresistance of these samples is studied, making use of recently formulated theory on the subject, and with experimental data taken over the magnetic field range 0 to 10 tesla. The results verify the connection between the mean amplitude of the fluctuations and the field correlation period, in terms of the correlation function introduced in the theory. The second work is on the impurity-assisted tunnelling conduction in a magnetic field of three thin rm n^{+}/n^{-}/n^ {+} GaAs sandwich layer structures. The conduction of the system is shown to be determined by impurities lying in the centre of the middle layer. This allows the connection to be made between the conductivity of the system in a magnetic field, and the field-dependent shape of the donor electron wavefunction. The relative variation in resistance with angle to an applied magnetic field was measured, and is shown to be in agreement with predictions based on calculations of the shape of a normalised hydrogenic state wavefunction in high magnetic fields. The third work concerns the tunnelling conduction of a symmetrical GaAs/(AlGa)As/GaAs hetero-barrier system. The current-voltage characteristics at low temperature are fully modelled for applied voltages up to 180mV, using conventional theory of tunnelling and a position-dependent effective mass in the barrier. Low current oscillations in the Fowler-Nordheim tunnelling regime, corresponding to quantum reflection at the

  18. Effects of branch height on leaf gas exchange, branch hydraulic conductance and branch sap flux in open-grown ponderosa pine.

    Science.gov (United States)

    Hubbard, Robert M; Bond, Barbara J; Senock, Randy S; Ryan, Michael G

    2002-06-01

    Recent studies have shown that stomata respond to changes in hydraulic conductance of the flow path from soil to leaf. In open-grown tall trees, branches of different heights may have different hydraulic conductances because of differences in path length and growth. We determined if leaf gas exchange, branch sap flux, leaf specific hydraulic conductance, foliar carbon isotope composition (delta13C) and ratios of leaf area to sapwood area within branches were dependent on branch height (10 and 25 m) within the crowns of four open-grown ponderosa pine (Pinus ponderosa Laws.) trees. We found no difference in leaf gas exchange or leaf specific hydraulic conductance from soil to leaf between the upper and lower canopy of our study trees. Branch sap flux per unit leaf area and per unit sapwood area did not differ between the 10- and 25-m canopy positions; however, branch sap flux per unit sapwood area at the 25-m position had consistently lower values. Branches at the 25-m canopy position had lower leaf to sapwood area ratios (0.17 m2 cm-2) compared with branches at the 10-m position (0.27 m2 cm-2) (P = 0.03). Leaf specific conductance of branches in the upper crown did not differ from that in the lower crown. Other studies at our site indicate lower hydraulic conductance, sap flux, whole-tree canopy conductance and photosynthesis in old trees compared with young trees. This study suggests that height alone may not explain these differences.

  19. Stochastic inverse modelling of hydraulic conductivity fields taking into account independent stochastic structures: A 3D case study

    Science.gov (United States)

    Llopis-Albert, C.; Capilla, J. E.

    2010-09-01

    SummaryMajor factors affecting groundwater flow through fractured rocks include the geometry of each fracture, its properties and the fracture-network connectivity together with the porosity and conductivity of the rock matrix. When modelling fractured rocks this is translated into attaining a characterization of the hydraulic conductivity ( K) as adequately as possible, despite its high heterogeneity. This links with the main goal of this paper, which is to present an improvement of a stochastic inverse model, named as Gradual Conditioning (GC) method, to better characterise K in a fractured rock medium by considering different K stochastic structures, belonging to independent K statistical populations (SP) of fracture families and the rock matrix, each one with its own statistical properties. The new methodology is carried out by applying independent deformations to each SP during the conditioning process for constraining stochastic simulations to data. This allows that the statistical properties of each SPs tend to be preserved during the iterative optimization process. It is worthwhile mentioning that so far, no other stochastic inverse modelling technique, with the whole capabilities implemented in the GC method, is able to work with a domain covered by several different stochastic structures taking into account the independence of different populations. The GC method is based on a procedure that gradually changes an initial K field, which is conditioned only to K data, to approximate the reproduction of other types of information, i.e., piezometric head and solute concentration data. The approach is applied to the Äspö Hard Rock Laboratory (HRL) in Sweden, where, since the middle nineties, many experiments have been carried out to increase confidence in alternative radionuclide transport modelling approaches. Because the description of fracture locations and the distribution of hydrodynamic parameters within them are not accurate enough, we address the

  20. Using random forests to explore the effects of site attributes and soil properties on near-saturated and saturated hydraulic conductivity

    Science.gov (United States)

    Jorda, Helena; Koestel, John; Jarvis, Nicholas

    2014-05-01

    Knowledge of the near-saturated and saturated hydraulic conductivity of soil is fundamental for understanding important processes like groundwater contamination risks or runoff and soil erosion. Hydraulic conductivities are however difficult and time-consuming to determine by direct measurements, especially at the field scale or larger. So far, pedotransfer functions do not offer an especially reliable alternative since published approaches exhibit poor prediction performances. In our study we aimed at building pedotransfer functions by growing random forests (a statistical learning approach) on 486 datasets from the meta-database on tension-disk infiltrometer measurements collected from peer-reviewed literature and recently presented by Jarvis et al. (2013, Influence of soil, land use and climatic factors on the hydraulic conductivity of soil. Hydrol. Earth Syst. Sci. 17(12), 5185-5195). When some data from a specific source publication were allowed to enter the training set whereas others were used for validation, the results of a 10-fold cross-validation showed reasonable coefficients of determination of 0.53 for hydraulic conductivity at 10 cm tension, K10, and 0.41 for saturated conductivity, Ks. The estimated average annual temperature and precipitation at the site were the most important predictors for K10, while bulk density and estimated average annual temperature were most important for Ks prediction. The soil organic carbon content and the diameter of the disk infiltrometer were also important for the prediction of both K10 and Ks. However, coefficients of determination were around zero when all datasets of a specific source publication were excluded from the training set and exclusively used for validation. This may indicate experimenter bias, or that better predictors have to be found or that a larger dataset has to be used to infer meaningful pedotransfer functions for saturated and near-saturated hydraulic conductivities. More research is in progress

  1. Diurnal depression in leaf hydraulic conductance at ambient and elevated [CO2] reveals anisohydric water management in field-grown soybean

    Science.gov (United States)

    Diurnal cycles of photosynthesis and water use in field-grown soybean (Glycine max) are tied to light intensity and vapor pressure deficit (VPD). At high mid-day VPD, transpiration rates can lead to a decline in leaf water potential if leaf hydraulic conductance is insufficient to supply water to in...

  2. Diurnal depression in leaf hydraulic conductance at ambient and elevated [CO2] and reveals anisohydric water management in field-grown soybean

    Science.gov (United States)

    Diurnal cycles of photosynthesis and water use in field-grown soybean (Glycine max) are tied to light intensity and vapor pressure deficit (VPD). At high mid-day VPD, transpiration rates can lead to a decline in leaf water potential ('leaf) if leaf hydraulic conductance (Kleaf) is insufficient to su...

  3. Abscisic Acid Regulation of Root Hydraulic Conductivity and Aquaporin Gene Expression Is Crucial to the Plant Shoot Growth Enhancement Caused by Rhizosphere Humic Acids.

    Science.gov (United States)

    Olaetxea, Maite; Mora, Verónica; Bacaicoa, Eva; Garnica, María; Fuentes, Marta; Casanova, Esther; Zamarreño, Angel M; Iriarte, Juan C; Etayo, David; Ederra, Iñigo; Gonzalo, Ramón; Baigorri, Roberto; García-Mina, Jose M

    2015-12-01

    The physiological and metabolic mechanisms behind the humic acid-mediated plant growth enhancement are discussed in detail. Experiments using cucumber (Cucumis sativus) plants show that the shoot growth enhancement caused by a structurally well-characterized humic acid with sedimentary origin is functionally associated with significant increases in abscisic acid (ABA) root concentration and root hydraulic conductivity. Complementary experiments involving a blocking agent of cell wall pores and water root transport (polyethylenglycol) show that increases in root hydraulic conductivity are essential in the shoot growth-promoting action of the model humic acid. Further experiments involving an inhibitor of ABA biosynthesis in root and shoot (fluridone) show that the humic acid-mediated enhancement of both root hydraulic conductivity and shoot growth depended on ABA signaling pathways. These experiments also show that a significant increase in the gene expression of the main root plasma membrane aquaporins is associated with the increase of root hydraulic conductivity caused by the model humic acid. Finally, experimental data suggest that all of these actions of model humic acid on root functionality, which are linked to its beneficial action on plant shoot growth, are likely related to the conformational structure of humic acid in solution and its interaction with the cell wall at the root surface.

  4. Wood anatomy reveals high theoretical hydraulic conductivity and low resistance to vessel implosion in a Cretaceous fossil forest from northern Mexico.

    Science.gov (United States)

    Martínez-Cabrera, Hugo I; Estrada-Ruiz, Emilio

    2014-01-01

    The Olmos Formation (upper Campanian), with over 60 angiosperm leaf morphotypes, is Mexico's richest Cretaceous flora. Paleoclimate leaf physiognomy estimates indicate that the Olmos paleoforest grew under wet and warm conditions, similar to those present in modern tropical rainforests. Leaf surface area, tree size and climate reconstructions suggest that this was a highly productive system. Efficient carbon fixation requires hydraulic efficiency to meet the evaporative demands of the photosynthetic surface, but it comes at the expense of increased risk of drought-induced cavitation. Here we tested the hypothesis that the Olmos paleoforest had high hydraulic efficiency, but was prone to cavitation. We characterized the hydraulic properties of the Olmos paleoforest using theoretical conductivity (Ks), vessel composition (S) and vessel fraction (F), and measured drought resistance using vessel implosion resistance (t/b)h(2) and the water potential at which there is 50% loss of hydraulic conductivity (P50). We found that the Olmos paleoforest had high hydraulic efficiency, similar to that present in several extant tropical-wet or semi-deciduous forest communities. Remarkably, the fossil flora had the lowest (t/b)h(2), which, together with low median P50 (-1.9 MPa), indicate that the Olmos paleoforest species were extremely vulnerable to drought-induced cavitation. Our findings support paleoclimate inferences from leaf physiognomy and paleoclimatic models suggesting it represented a highly productive wet tropical rainforest. Our results also indicate that the Olmos Formation plants had a large range of water conduction strategies, but more restricted variation in cavitation resistance. These straightforward methods for measuring hydraulic properties, used herein for the first time, can provide useful information on the ecological strategies of paleofloras and on temporal shifts in ecological function of fossil forests chronosequences.

  5. Electronic conductivity studies on oxyhalide glasses containing TMO

    Energy Technology Data Exchange (ETDEWEB)

    Vijayatha, D. [R& D Center, Bharatiar University, Coimbatore, Tamil Nadu (India); Department of Physics, Gurunanak Institute of Technology, Hyderabad -040 (India); Viswanatha, R. [Solid State and Structural Chemistry Unit, Indian Institute of Science, Bangalore 560012 (India); Sujatha, B. [Department of Electronics and Communcation, MSRIT, Bangalore 560054 (India); Narayana Reddy, C., E-mail: nivetejareddy@gmail.com [Department of Physics, Sree Siddaganga College of Arts, Science and Commerce, Tumkur 572102 (India)

    2016-05-06

    Microwave-assisted synthesis is cleaner, more economical and much faster than conventional methods. The development of new routes for the synthesis of solid materials is an integral part of material science and technology. The electronic conductivity studies on xPbCl{sub 2} – 60 PbO – (40-x) V{sub 2}O{sub 5} (1 ≥ x ≤ 10) glass system has been carried out over a wide range of composition and temperature (300 K to 423 K). X-ray diffraction study confirms the amorphous nature of the samples. The Scanning electron microscopic studies reveal the formation of cluster like morphology in PbCl{sub 2} containing glasses. The d.c conductivity exhibits Arrhenius behaviour and increases with V{sub 2}O{sub 5} concentration. Analysis of the results is interpreted in view Austin-Mott’s small polaron model of electron transport. Activation energies calculated using regression analysis exhibit composition dependent trend and the variation is explained in view of the structure of lead-vanadate glass.

  6. Use of time-subsidence data during pumping to characterize specific storage and hydraulic conductivity of semi-confining units

    Science.gov (United States)

    Burbey, T. J.

    2003-09-01

    A new graphical technique is developed that takes advantage of time-subsidence data collected from either traditional extensometer installations or from newer technologies such as fixed-station global positioning systems or interferometric synthetic aperture radar imagery, to accurately estimate storage properties of the aquifer and vertical hydraulic conductivity of semi-confining units. Semi-log plots of time-compaction data are highly diagnostic with the straight-line portion of the plot reflecting the specific storage of the semi-confining unit. Calculation of compaction during one-log cycle of time from these plots can be used in a simple analytical expression based on the Cooper-Jacob technique to accurately calculate specific storage of the semi-confining units. In addition, these semi-log plots can be used to identify when the pressure transient has migrated through the confining layer into the unpumped aquifer, precluding the need for additional piezometers within the unpumped aquifer or within the semi-confining units as is necessary in the Neuman and Witherspoon method. Numerical simulations are used to evaluate the accuracy of the new technique. The technique was applied to time-drawdown and time-compaction data collected near Franklin Virginia, within the Potomac aquifers of the Coastal Plain, and shows that the method can be easily applied to estimate the inelastic skeletal specific storage of this aquifer system.

  7. HydrogeoSieveXL: an Excel-based tool to estimate hydraulic conductivity from grain-size analysis

    Science.gov (United States)

    Devlin, J. F.

    2015-06-01

    For over a century, hydrogeologists have estimated hydraulic conductivity ( K) from grain-size distribution curves. The benefits of the practice are simplicity, cost, and a means of identifying spatial variations in K. Many techniques have been developed over the years, but all suffer from similar shortcomings: no accounting of heterogeneity within samples (i.e., aquifer structure is lost), loss of grain packing characteristics, and failure to account for the effects of overburden pressure on K. In addition, K estimates can vary by an order of magnitude between the various methods, and it is not generally possible to identify the best method for a given sample. The drawbacks are serious, but the advantages have seen the use of grain-size distribution curves for K estimation continue, often using a single selected method to estimate K in a given project. In most cases, this restriction results from convenience. It is proposed here that extending the analysis to include several methods would be beneficial since it would provide a better indication of the range of K that might apply. To overcome the convenience limitation, an Excel-based spreadsheet program, HydrogeoSieveXL, is introduced here. HydrogeoSieveXL is a freely available program that calculates K from grain-size distribution curves using 15 different methods. HydrogeoSieveXL was found to calculate K values essentially identical to those reported in the literature, using the published grain-size distribution curves.

  8. Taking into account the temporal variation of hydraulic conductivity when calibrating overland flow models on tilled fields.

    Science.gov (United States)

    Chahinian, N.; Andrieux, P.; Moussa, R.; Voltz, M.

    2003-04-01

    Tillage operations are known to change the structure of agricultural soils. In this paper we seek a calibration methodology to take into account the impact of tillage on overland flow simulation at the scale of a tilled field located in southern France. The study site is a 3240 m2 vineyard equipped with a Venturi flume and a tipping bucket rain gauge. 20 monitored rainfall events were used for the study, equally divided between calibration and validation sets. The overland flow model used consists of a modified Green &Ampt equation to simulate infiltration, a surface detention module, and an overland flow routing module based on the unit hydrograph concept. The model parameters that were calibrated for each event are the saturated hydraulic conductivity and the random roughness. The calibrated Ks values decreased monotonously according to the total amount of rainfall since tillage. No clear relationship was observed between the random roughness and cumulated rainfall. A regression curve was fitted to the calibrated Ks values. This curve was then used to determine Ks values for any rainfall event considering the total rainfall since tillage. Fairly good agreement was observed between the simulated and measured hydrographs of the calibration set. The validation results were relatively poorer but remain satisfactory given the uncertainties related to the initial soil moisture conditions. The calibration methodology developed seems robust and may be transposed to other sites.

  9. A field-scale infiltration model accounting for spatial heterogeneity of rainfall and soil saturated hydraulic conductivity

    Science.gov (United States)

    Morbidelli, Renato; Corradini, Corrado; Govindaraju, Rao S.

    2006-04-01

    This study first explores the role of spatial heterogeneity, in both the saturated hydraulic conductivity Ks and rainfall intensity r, on the integrated hydrological response of a natural slope. On this basis, a mathematical model for estimating the expected areal-average infiltration is then formulated. Both Ks and r are considered as random variables with assessed probability density functions. The model relies upon a semi-analytical component, which describes the directly infiltrated rainfall, and an empirical component, which accounts further for the infiltration of surface water running downslope into pervious soils (the run-on effect). Monte Carlo simulations over a clay loam soil and a sandy loam soil were performed for constructing the ensemble averages of field-scale infiltration used for model validation. The model produced very accurate estimates of the expected field-scale infiltration rate, as well as of the outflow generated by significant rainfall events. Furthermore, the two model components were found to interact appropriately for different weights of the two infiltration mechanisms involved.

  10. The effect of nutrient enrichment on growth, photosynthesis and hydraulic conductance of dwarf mangroves in Panamá

    Science.gov (United States)

    Lovelock, C.E.; Feller, Ilka C.; McKee, K.L.; Engelbrecht, B.M.J.; Ball, M.C.

    2004-01-01

    1. Dwarf stands of the mangrove Rhizophora mangle L. are extensive in the Caribbean. We fertilized dwarf trees in Almirante Bay, Bocas del Toro Province, north-eastern Panama with nitrogen (N) and phosphorus (P) to determine (1) if growth limitations are due to nutrient deficiency; and (2) what morphological and/or physiological factors underlie nutrient limitations to growth. 2. Shoot growth was 10-fold when fertilized with P and twofold with N fertilization, indicating that stunted growth of these mangroves is partially due to nutrient deficiency. 3. Growth enhancements caused by N or P enrichment could not be attributed to increases in photosynthesis on a leaf area basis, although photosynthetic nutrient-use efficiency was improved. The most dramatic effect was on stem hydraulic conductance, which was increased sixfold by P and 2-5-fold with N enrichment. Fertilization with P enhanced leaf and stem P concentrations and reduced C:N ratio, but did not alter leaf damage by herbivores. 4. Our findings indicate that addition of N and P significantly alter tree growth and internal nutrient dynamics of mangroves at Bocas del Toro, but also that the magnitude, pattern and mechanisms of change will be differentially affected by each nutrient.

  11. Conductive Elastomers for Stretchable Electronics, Sensors and Energy Harvesters

    Directory of Open Access Journals (Sweden)

    Jin-Seo Noh

    2016-04-01

    Full Text Available There have been a wide variety of efforts to develop conductive elastomers that satisfy both mechanical stretchability and electrical conductivity, as a response to growing demands on stretchable and wearable devices. This article reviews the important progress in conductive elastomers made in three application fields of stretchable technology: stretchable electronics, stretchable sensors, and stretchable energy harvesters. Diverse combinations of insulating elastomers and non-stretchable conductive materials have been studied to realize optimal conductive elastomers. It is noted that similar material combinations and similar structures have often been employed in different fields of application. In terms of stretchability, cyclic operation, and overall performance, fields such as stretchable conductors and stretchable strain/pressure sensors have achieved great advancement, whereas other fields like stretchable memories and stretchable thermoelectric energy harvesting are in their infancy. It is worth mentioning that there are still obstacles to overcome for the further progress of stretchable technology in the respective fields, which include the simplification of material combination and device structure, securement of reproducibility and reliability, and the establishment of easy fabrication techniques. Through this review article, both the progress and obstacles associated with the respective stretchable technologies will be understood more clearly.

  12. Mixed oxygen ion/electron-conducting ceramics for oxygen separation

    Energy Technology Data Exchange (ETDEWEB)

    Stevenson, J.W.; Armstrong, T.R.; Armstrong, B.L. [Pacific Northwest National Lab., Richland, WA (United States)

    1996-08-01

    Mixed oxygen ion and electron-conducting ceramics are unique materials that can passively separate high purity oxygen from air. Oxygen ions move through a fully dense ceramic in response to an oxygen concentration gradient, charge-compensated by an electron flux in the opposite direction. Compositions in the system La{sub 1{minus}x}M{sub x}Co{sub 1{minus}y{minus}z}Fe{sub y}N{sub z}O{sub 3{minus}{delta}}, perovskites where M=Sr, Ca, and Ba, and N=Mn, Ni, Cu, Ti, and Al, have been prepared and their electrical, oxygen permeation, oxygen vacancy equilibria, and catalytic properties evaluated. Tubular forms, disks, and asymmetric membrane structures, a thin dense layer on a porous support of the same composition, have been fabricated for testing purposes. In an oxygen partial gradient, the passive oxygen flux through fully dense structures was highly dependent on composition. An increase in oxygen permeation with increased temperature is attributed to both enhanced oxygen vacancy mobility and higher vacancy populations. Highly acceptor-doped compositions resulted in oxygen ion mobilities more than an order of magnitude higher than yttria-stabilized zirconia. The mixed conducting ceramics have been utilized in a membrane reactor configuration to upgrade methane to ethane and ethylene. Conditions were established to balance selectivity and throughput in a catalytic membrane reactor constructed from mixed conducting ceramics.

  13. Determination of the saturated film conductivity to improve the EMFX model in describing the soil hydraulic properties over the entire moisture range

    Science.gov (United States)

    Wang, Yunquan; Ma, Jinzhu; Guan, Huade; Zhu, Gaofeng

    2017-06-01

    Difficulty in measuring hydraulic conductivity, particularly under dry conditions, calls for methods of predicting the conductivity from easily obtained soil properties. As a complement to the recently published EMFX model, a method based on two specific suction conditions is proposed to estimate saturated film conductivity from the soil water retention curve. This method reduces one fitting parameter in the previous EMFX model, making it possible to predict the hydraulic conductivity from the soil water retention curve over the complete moisture range. Model performance is evaluated with published data of soils in a broad texture range from sand to clay. The testing results indicate that 1) the modified EMFX model (namely the EMFX-K model), incorporating both capillary and adsorption forces, provides good agreement with the conductivity data over the entire moisture range; 2) a value of 0.5 for the tortuosity factor in the EMFX-K model as that in the Mualem's model gives comparable estimation of the relative conductivity associated with the capillary force; and 3) a value of -1.0 × 10-20 J for the Hamaker constant, rather than the commonly used value of -6.0 × 10-20 J, appears to be more appropriate to represent solely the effect of the van der Waals forces and to predict the film conductivity. In comparison with the commonly used van Genuchten-Mualem model, the EMFX-K model significantly improves the prediction of hydraulic conductivity under dry conditions. The sensitivity analysis result suggests that the uncertainty in the film thickness estimation is important in explaining the model underestimation of hydraulic conductivity for the soils with fine texture, in addition to the uncertainties from the measurements and the model structure. High quality data that cover the complete moisture range for a variety of soil textures are required to further test the method.

  14. High frequency conductivity of hot electrons in carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Amekpewu, M., E-mail: mamek219@gmail.com [Department of Applied Physics, University for Development Studies, Navrongo (Ghana); Mensah, S.Y. [Department of Physics, College of Agriculture and Natural Sciences, U.C.C. (Ghana); Musah, R. [Department of Applied Physics, University for Development Studies, Navrongo (Ghana); Mensah, N.G. [Department of Mathematics, College of Agriculture and Natural Sciences, U.C.C. (Ghana); Abukari, S.S.; Dompreh, K.A. [Department of Physics, College of Agriculture and Natural Sciences, U.C.C. (Ghana)

    2016-05-01

    High frequency conductivity of hot electrons in undoped single walled achiral Carbon Nanotubes (CNTs) under the influence of ac–dc driven fields was considered. We investigated semi-classically Boltzmann's transport equation with and without the presence of the hot electrons’ source by deriving the current densities in CNTs. Plots of the normalized current density versus frequency of ac-field revealed an increase in both the minimum and maximum peaks of normalized current density at lower frequencies as a result of a strong injection of hot electrons. The applied ac-field plays a twofold role of suppressing the space-charge instability in CNTs and simultaneously pumping an energy for lower frequency generation and amplification of THz radiations. These have enormous promising applications in very different areas of science and technology.

  15. Practical estimates of field-saturated hydraulic conductivity of bedrock outcrops using a modified bottomless bucket method

    Science.gov (United States)

    Mirus, Benjamin B.; Perkins, Kim S.

    2012-01-01

    The bottomless bucket (BB) approach (Nimmo et al., 2009a) is a cost-effective method for rapidly characterizing field-saturated hydraulic conductivity Kfs of soils and alluvial deposits. This practical approach is of particular value for quantifying infiltration rates in remote areas with limited accessibility. A similar approach for bedrock outcrops is also of great value for improving quantitative understanding of infiltration and recharge in rugged terrain. We develop a simple modification to the BB method for application to bedrock outcrops, which uses a non-toxic, quick-drying silicone gel to seal the BB to the bedrock. These modifications to the field method require only minor changes to the analytical solution for calculating Kfs on soils. We investigate the reproducibility of the method with laboratory experiments on a previously studied calcarenite rock and conduct a sensitivity analysis to quantify uncertainty in our predictions. We apply the BB method on both bedrock and soil for sites on Pahute Mesa, which is located in a remote area of the Nevada National Security Site. The bedrock BB tests may require monitoring over several hours to days, depending on infiltration rates, which necessitates a cover to prevent evaporative losses. Our field and laboratory results compare well to Kfs values inferred from independent reports, which suggests the modified BB method can provide useful estimates and facilitate simple hypothesis testing. The ease with which the bedrock BB method can be deployed should facilitate more rapid in-situ data collection than is possible with alternative methods for quantitative characterization of infiltration into bedrock.

  16. Magnetic induction technique for mapping vertical conductive fractures: electronic design

    Energy Technology Data Exchange (ETDEWEB)

    Landt, J.A.; Koelle, A.R.; Trump, M.A.; Nickell, J.D. Jr.

    1978-09-01

    This report is the last in a series that describes the preliminary design of an instrument capable of mapping conductive fractures deep below the surface of the earth. Earlier reports dealt with theoretical analysis, the general status of the instrument development, and materials vendor searches. Here, attention is focused on the electronics design and prototype hardware to perform the mapping task. A phase-sensitive detector is described that has a sensitivity in the tens of nanovolts. Coil-switching circuitry is also described, as well as a downhole data link tailor-made for this particular instrument's needs.

  17. Thermal Conductance of a Single-Electron Transistor

    Science.gov (United States)

    Dutta, B.; Peltonen, J. T.; Antonenko, D. S.; Meschke, M.; Skvortsov, M. A.; Kubala, B.; König, J.; Winkelmann, C. B.; Courtois, H.; Pekola, J. P.

    2017-08-01

    We report on combined measurements of heat and charge transport through a single-electron transistor. The device acts as a heat switch actuated by the voltage applied on the gate. The Wiedemann-Franz law for the ratio of heat and charge conductances is found to be systematically violated away from the charge degeneracy points. The observed deviation agrees well with the theoretical expectation. With a large temperature drop between the source and drain, the heat current away from degeneracy deviates from the standard quadratic dependence in the two temperatures.

  18. New secondary batteries utilizing electronically conductive polymer cathodes

    Science.gov (United States)

    Martin, Charles R.; White, Ralph E.

    1989-01-01

    The objectives of this project are to characterize the transport properties in electronically conductive polymers and to assess the utility of these films as cathodes in lithium/polymer secondary batteries. During this research period, progress has been made in a literature survey of the historical background, methods of preparation, the physical and chemical properties, and potential technological applications of polythiophene. Progress has also been made in the characterization of polypyrrole flat films and fibrillar films. Cyclic voltammetry and potential step chronocoulometry were used to gain information on peak currents and potentials switching reaction rates, charge capacity, and charge retention. Battery charge/discharge studies were also performed.

  19. Hydraulic Conductivity Measurements with HTU at Eurajoki, Olkiluoto, Borehole OL-KR15 and OL-KR15B, Year 2004

    Energy Technology Data Exchange (ETDEWEB)

    Haemaelaeinen, H.

    2005-07-01

    As a part of the site investigations for the disposal of spent nuclear fuel, hydraulic conductivity measurements were carried out in borehole OL-KR15 at Eurajoki, Olkiluoto. The objective was to investigate the distribution of the hydraulic conductivity in the surrounding bedrock volume. Measurements were carried out during 2003-2004 in two phases. The total length of the borehole OL-KR15 is 518,85 m and 158 45,14 m. Of the 471 ,5 m + 44,5 m total measurable length 414 m was covered with 237 standard tests with 2 m packer separation as specified in the research plan, partly with 1 m overlaps. 259 tests were initiated, but some of them ended to hardware or software errors or unsuitable parameter values. Double-packer constant-head method was used throughout with nominal 200 kPa overpressure. Injection stage lasted normally 20 minutes and fall-off stage 10 minutes. The tests were often shortened if there were clear indications that the hydraulic conductivity is below the measuring range of the system. The pressure in the test section was let to stabilise at least 5 min before injection. In some test sections the stabilisation or injection stage lasted several hours. Two transient (Horner and 1/Q) interpretations and one stationary-state (Moye) interpretation were made in-situ immediately after the test. The Hydraulic Testing Unit (HTU-system) is owned by Posiva Oy and it was operated by Geopros Oy. (orig.)

  20. Comparative study of electron conduction in azulene and naphthalene

    Indian Academy of Sciences (India)

    Sudipta Dutta; S Lakshmi; Swapan K Pati

    2008-06-01

    We have studied the feasibility of electron conduction in azulene molecule and compared with that in its isomer naphthalene. We have used non-equilibrium Green’s function formalism to measure the current in our systems as a response of the external electric field. Parallely we have performed the Gaussian calculations with electric field in the same bias window to observe the impact of external bias on the wave functions of the systems. We have found that the conduction of azulene is higher than that of naphthalene inspite of its intrinsic donor–acceptor property, which leads a system to more insulating state. Due to stabilization through charge transfer the azulene system can be fabricated as a very effective molecular wire. Our calculations show the possibility of huge device application of azulene in nano-scale instruments.

  1. Enhancement of thermal contact conductance for electronic systems

    Energy Technology Data Exchange (ETDEWEB)

    Sartre, V.; Lallemand, M. [Centre de Thermique de Lyon, UMR CNRS 5008, INSA, Villeurbanne (France)

    2001-02-01

    Experimental investigations on thermal contact resistance have been performed. The results of this study will be useful in selecting interstitial materials to enhance the thermal conductance of an electronic component/heat sink assembly. The experimental assembly consists of two specimens: a thick copper plate, electrically heated, and an aluminium water-cooled plate. The two specimens are bolted together and the load is applied using a calibrated torque wrench. Various interstitial materials (seven commercial greases and 12 foils) suitable for the thermal enhancement in electronic systems have been investigated. The variables considered are the bolt torque, the heat transfer rate and the grease or foil thickness. Results show that the most influential parameter is the applied torque. The contact resistance decreases as the heat flux or the film thickness decreases. The highest dimensionless contact conductance factors (E) are achieved with greases (3 < E < 6). Phase change material-coated foils exhibit E-values ranging from 2.5 to 3.5. Graphite or metallic foils have E-values lower than 2 and for silicone foils E is significantly reduced (E < 1). Thus, phase change material-coated foils seem to be very promising materials, since they are efficient, easy to implement and do not migrate and vaporise out of the contact area. (author)

  2. Electrically and Thermally Conducting Nanocomposites for Electronic Applications

    Directory of Open Access Journals (Sweden)

    Daryl Santos

    2010-02-01

    Full Text Available Nanocomposites made up of polymer matrices and carbon nanotubes are a class of advanced materials with great application potential in electronics packaging. Nanocomposites with carbon nanotubes as fillers have been designed with the aim of exploiting the high thermal, electrical and mechanical properties characteristic of carbon nanotubes. Heat dissipation in electronic devices requires interface materials with high thermal conductivity. Here, current developments and challenges in the application of nanotubes as fillers in polymer matrices are explored. The blending together of nanotubes and polymers result in what are known as nanocomposites. Among the most pressing current issues related to nanocomposite fabrication are (i dispersion of carbon nanotubes in the polymer host, (ii carbon nanotube-polymer interaction and the nature of the interface, and (iii alignment of carbon nanotubes in a polymer matrix. These issues are believed to be directly related to the electrical and thermal performance of nanocomposites. The recent progress in the fabrication of nanocomposites with carbon nanotubes as fillers and their potential application in electronics packaging as thermal interface materials is also reported.

  3. Analysis of hydraulic tests of the Culebra and Magenta Dolomites and Dewey Lake Redbeds conducted at the Waste Isolation Pilot Plant Site

    Energy Technology Data Exchange (ETDEWEB)

    Beauheim, R.L. [Sandia National Labs., Albuquerque, NM (United States). Geohydrology Dept.; Ruskauff, G.J. [Duke Engineering and Services, Inc., Albuquerque, NM (United States)

    1998-09-01

    This report presents interpretations of hydraulic tests conducted at 15 well locations in the vicinity of the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico between 1980 and 1996. The WIPP is a US Department of Energy (DOE) facility to demonstrate safe disposal of transuranic wastes arising form the nation`s defense programs. The WIPP repository lies within bedded halite of the Salado Formation, 2,155 ft below ground surface. The tests reported herein were, with two exceptions, conducted in the Culebra Dolomite member of the Rustler Formation, which overlies the Salado Formation. The remaining tests were conducted in the Magenta Member of the Rustler and in the overlying formation, the Dewey Lake Redbeds. This report completes the documentation of hydraulic-test interpretations used as input to the WIPP Compliance Certification Application (US DOE, 1996).

  4. Analysis of 6-year fluid electric conductivity logs to evaluate the hydraulic structure of the deep drill hole at Outokumpu, Finland

    Science.gov (United States)

    Sharma, Prabhakar; Tsang, Chin-Fu; Kukkonen, Ilmo T.; Niemi, Auli

    2016-07-01

    Over the last two decades, the flowing fluid electric conductivity (FFEC) logging method has been applied in boreholes in the well-testing mode to evaluate the transmissivity, hydraulic head, and formation water electrical conductivity as a function of depth with a resolution of about 10-20 cm. FFEC profiles along the borehole are obtained under both shut-in and pumping conditions in a logging procedure that lasts only 3 or 4 days. A method for analyzing these FFEC logs has been developed and successfully employed to obtain formation parameters in a number of field studies. The present paper concerns the analysis of a unique set of FFEC logs that were taken from a deep borehole reaching down to 2.5 km at Outokumpu, Finland, over a 6-year time period. The borehole intersects paleoproterozoic metasedimentary, granitoid, and ophiolite-derived rocks. After the well was drilled, completed, and cleaned up, FFEC logs were obtained after 7, 433, 597, 948, and 2036 days. In analyzing these five profiles, we discovered the need to account for salinity diffusion from water in the formation to the borehole. Analysis results include the identification of 15 hydraulically conducting zones along the borehole, the calculation of flow rates associated with these 15 zones, as well as the estimation of the variation of formation water electrical conductivity as a function of depth. The calculated flow rates were used to obtain the tentative hydraulic conductivity values at these 15 depth levels.

  5. Root tip morphology, anatomy, chemistry and potential hydraulic conductivity vary with soil depth in three temperate hardwood species.

    Science.gov (United States)

    Wang, Yan; Dong, Xueyun; Wang, Hongfeng; Wang, Zhengquan; Gu, Jiacun

    2016-01-01

    Root traits in morphology, chemistry and anatomy are important to root physiological functions, but the differences between shallow and deep roots have rarely been studied in woody plants. Here, we selected three temperate hardwood species, Juglans mandshurica Maxim., Fraxinus mandschurica Rupr. and Phellodendron amurense Rupr., in plantations in northeastern China and measured morphological, anatomical and chemical traits of root tips (i.e., the first-order roots) at surface (0-10 cm) and subsurface (20-30 cm) soil layers. The objectives of this study were to identify how those traits changed with soil depth and to reveal potential functional differences. The results showed that root diameters in deep root tips were greater in J. mandshurica and F. mandschurica, but smaller in P. amurense. However, root stele diameter and the ratio of stele to root diameter in the subsurface layer were consistently greater in all three species, which may enhance their abilities to penetrate into soil. All deep roots exhibited lower tissue nitrogen concentration and respiration rate, which were possibly caused by lower nutrient availability in the subsurface soil layer. Significant differences between shallow and deep roots were observed in xylem structure, with deep roots having thicker stele, wider maximum conduit and greater number of conduits per stele. Compared with shallow roots, the theoretical hydraulic conductivities in deep roots were enhanced by 133% (J. mandshurica), 78% (F. mandschurica) and 217% (P. amurense), respectively, indicating higher efficiency of transportation. Our results suggest that trees' root tip anatomical structure and physiological activity vary substantially with soil environment.

  6. Linking hydropedology and ecosystem services: differential controls of surface field saturated hydraulic conductivity in a volcanic setting in central Mexico

    Directory of Open Access Journals (Sweden)

    A. Gómez-Tagle

    2009-03-01

    Full Text Available In this study the variation of field saturated soil hydraulic conductivity (Kfs as key control variable and descriptor of infiltration was examined by means of a constant head single ring infiltrometer. The study took place in five coverage types and land uses in a volcanic setting in central Mexico. The tested hypothesis was that there exist a positive relationship between plant cover and surface Kfs for the study area. The examined coverage types included; Second growth pine-oak forest, pasture land, fallow land, gully and Cupresus afforestation. Results indicate that Kfs did not depend exclusively of plant cover; it was related to surface horizontal expression of the unburied soil horizons and linked to land use history. Therefore the Kfs measured at a certain location did not depend exclusively of the actual land use, it was also influenced by soil bioturbation linked to plant succession patterns and land use management practices history. The hypothesis accounts partially the variation between sites. Kfs under dense plant cover at the Cupresus afforestation was statistically equal to that measured at the fallow land or the gully sites, while second growth pine-oak forest Kfs figures were over an order of magnitude higher than the rest of the coverage types. The results suggest the relevance of unburied soil horizons in the soil hydrologic response when present at the surface. Under these conditions loosing surface soil horizons due to erosion, not only fertility is lost, but environmental services generation potential. A conceptual model within the hydropedological approach is proposed. It explains the possible controls of Kfs, for this volcanic setting. Land use history driven erosion plays a decisive role in subsurface horizon presence at the surface and soil matrix characteristic determination, while plant succession patterns seem to be strongly linked to soil bioturbation and

  7. Enhanced biogeochemical cycling and subsequent reduction of hydraulic conductivity associated with soil-layer interfaces in the vadose zone.

    Science.gov (United States)

    Hansen, David J; McGuire, Jennifer T; Mohanty, Binayak P

    2011-01-01

    Biogeochemical dynamics in the vadose zone are poorly understood due to the transient nature of chemical and hydrologic conditions but are nonetheless critical to understanding chemical fate and transport. This study explored the effects of a soil layer on linked geochemical, hydrological, and microbiological processes. Three laboratory soil columns were constructed: a homogenized medium-grained sand, a homogenized organic-rich loam, and a sand-over-loam layered column. Upward and downward infiltration of water was evaluated during experiments to simulate rising water table and rainfall events, respectively. In situ collocated probes measured soil water content, matric potential, and Eh. Water samples collected from the same locations were analyzed for Br, Cl, NO, SO, NH, Fe, and total sulfide. Compared with homogeneous columns, the presence of a soil layer altered the biogeochemistry and water flow of the system considerably. Enhanced biogeochemical cycling was observed in the layered column over the texturally homogeneous soil columns. Enumerations of iron- and sulfate-reducing bacteria showed 1 to 2 orders of magnitude greater community numbers in the layered column. Mineral and soil aggregate composites were most abundant near the soil-layer interface, the presence of which likely contributed to an observed order-of-magnitude decrease in hydraulic conductivity. These findings show that quantifying coupled hydrologic-biogeochemical processes occurring at small-scale soil interfaces is critical to accurately describing and predicting chemical changes at the larger system scale. These findings also provide justification for considering soil layering in contaminant fate and transport models because of its potential to increase biodegradation or to slow the rate of transport of contaminants.

  8. Electronic conduction and electrocatalysis by supramolecular tetraruthenated copper porphyrazine films

    Energy Technology Data Exchange (ETDEWEB)

    Matsumoto, Marcio Y.; Toyama, Marcos M.; Mayer, Ildemar; Winnischofer, Herbert; Araki, Koiti; Toma, Henrique E. [Universidade de Sao Paulo (USP), SP (Brazil). Inst. de Quimica

    2009-07-01

    A new tetraruthenated copper(II)-tetra(3,4-pyridyl)porphyrazine species, [CuTRPyPz]{sup 4+}, has been synthesized and fully characterized by means of analytical, spectroscopic and electrochemical techniques. This {pi}-conjugated system contrasts with the related meso-tetrapyridylporphyrins by exhibiting strong electronic interaction between the coordinated peripheral complexes and the central ring. Based on favorable {pi}-stacking and electrostatic interactions, layer-by-layer assembled films were successfully generated from the appropriate combination of [CuTRPyPz]{sup 4+} with copper(II)-tetrasulfonated phtalocyanine, [CuTSPc]{sup 4-}. Their conducting and electrocatalytic properties were investigated by means of impedance spectroscopy and rotating disc voltammetry, exhibiting metallic behavior near the Ru(III/II) redox potential, as well as enhanced catalytic activity for the oxidation of nitrite and sulphite ions. (author)

  9. Design and Experiment of Electronic-hydraulic Loading Test-bed Based on Tractor’s Hydraulic Steering By-wire

    Institute of Scientific and Technical Information of China (English)

    Yue JIN; Yang LU; Jiahui GONG; Zhixiong LU; Wenming LI; Jungan WU

    2015-01-01

    An Electro-hydraulic loading system is designed based on a test-bed of tractor’s hydraulic steering by-wire. To simulate the steering resistance driving tractor in many kinds of soils and roads,the loading force is controlled to make proportional and continuous variable by an electro-hydraulic proportional relief valve. A steering resistance loading test-bed is built to test three kinds of steering resistance including constant,step and sine style. Tire lateral resistance is also tested under different steering conditions. The result shows that the electro-hydraulic loading system has high stability and following performance. Besides,the system’s steady state error is lower than 3. 1%,and it meets the test requirement of tractor’s hydraulic steering by-wire.

  10. Suppression of Electron Thermal Conduction in the Intracluster Medium

    Science.gov (United States)

    Roberg-Clark, Gareth; Drake, James; Swisdak, M.; Reynolds, Christopher S.

    2017-08-01

    The Intracluster Medium (ICM) contains high-temperature dilute plasma in which the quantity beta, defined as the ratio of the thermal pressure of the gas to the local magnetic field pressure, is much larger than unity. In addition, the collisional mean free path of particles in the ICM is typically large compared to the magnetic gyro-radius of individual particles. These conditions allow for the growth of robust microinstabilities that can significantly alter the transport of particles and heat along the local magnetic field line. Here we explore such an instability using driven two-dimensional Particle-In-Cell simulations of a magnetized plasma with a temperature gradient imposed at the boundaries. The system is highly unstable and develops large-amplitude magnetic fluctuations that effectively scatter the orbits of electrons crossing the simulation domain, resulting in a collisionless suppression of thermal conduction across the temperature gradient and magnetic field. The results suggest that the spontaneous development of small-scale plasma turbulence in the ICM may play a pivotal role in determining the thermal conductivity of ICM-like plasmas.

  11. Effective Saturated Hydraulic Conductivity for Representing Field-Scale Infiltration and Surface Soil Moisture in Heterogeneous Unsaturated Soils Subjected to Rainfall Events

    Directory of Open Access Journals (Sweden)

    Richa Ojha

    2017-02-01

    Full Text Available Spatial heterogeneity in soil properties has been a challenge for providing field-scale estimates of infiltration rates and surface soil moisture content over natural fields. In this study, we develop analytical expressions for effective saturated hydraulic conductivity for use with the Green-Ampt model to describe field-scale infiltration rates and evolution of surface soil moisture over unsaturated fields subjected to a rainfall event. The heterogeneity in soil properties is described by a log-normal distribution for surface saturated hydraulic conductivity. Comparisons between field-scale numerical and analytical simulation results for water movement in heterogeneous unsaturated soils show that the proposed expressions reproduce the evolution of surface soil moisture and infiltration rate with time. The analytical expressions hold promise for describing mean field infiltration rates and surface soil moisture evolution at field-scale over sandy loam and loamy sand soils.

  12. Assessing the likely value of gravity and drawdown measurements to constrain estimates of hydraulic conductivity and specific yield during unconfined aquifer testing

    Science.gov (United States)

    Blainey, J.B.; Ferre, T. P. A.; Cordova, J.T.

    2007-01-01

    Pumping of an unconfined aquifer can cause local desaturation detectable with high-resolution gravimetry. A previous study showed that signal-to-noise ratios could be predicted for gravity measurements based on a hydrologic model. We show that although changes should be detectable with gravimeters, estimations of hydraulic conductivity and specific yield based on gravity data alone are likely to be unacceptably inaccurate and imprecise. In contrast, a transect of low-quality drawdown data alone resulted in accurate estimates of hydraulic conductivity and inaccurate and imprecise estimates of specific yield. Combined use of drawdown and gravity data, or use of high-quality drawdown data alone, resulted in unbiased and precise estimates of both parameters. This study is an example of the value of a staged assessment regarding the likely significance of a new measurement method or monitoring scenario before collecting field data. Copyright 2007 by the American Geophysical Union.

  13. A method for mapping topsoil field-saturated hydraulic conductivity in the Cévennes-Vivarais region using infiltration tests conducted with different techniques

    Science.gov (United States)

    Braud, Isabelle; Desprats, Jean-François; Ayral, Pierre-Alain; Bouvier, Christophe; Vandervaere, Jean-Pierre

    2017-04-01

    Topsoil field-saturated hydraulic conductivity, Kfs, is a parameter that controls the partition of rainfall between infiltration and runoff. It is a key parameter in most distributed hydrological models. However, there is a mismatch between the scale of local in situ measurements and the scale at which the parameter is required in models. Therefore it is necessary to design methods to regionally map this parameter at the model scale. The paper propose a method for mapping Kfs in the Cévennes-Vivarais region, south-east France, using more easily available GIS data: geology and land cover. The mapping is based on a data set gathering infiltration tests performed in the area or close to it for more than ten years. The data set is composed of infiltration tests performed using various techniques: Guelph permeameter, double ring and single ring infiltration tests, infiltrometers with multiple suctions. The different methods lead to different orders of magnitude for Kfs rendering the pooling of all the data challenging. Therefore, a method is first proposed to pool the data from the different infiltration methods, leading to a homogenized set of Kfs, based on an equivalent double ring/tension disk infiltration value. Statistical tests showed significant differences in distributions among different geologies and land covers. Thus those variables were retained as proxy for mapping Kfs at the regional scale. This map was compared to a map based on the Rawls and Brakensiek (RB) pedo-transfer function (Manus et al., 2009, Vannier et al., 2016), showing very different patterns between both maps. In addition, RB values did not fit observed values at the plot scale, highlighting that soil texture only is not a good predictor of Kfs. References Manus, C., Anquetin, S., Braud, I., Vandervaere, J.P., Viallet, P., Creutin, J.D., Gaume, E., 2009. A modelling approach to assess the hydrological response of small Mediterranean catchments to the variability of soil characteristics in a

  14. Hydraulic conduction system for an underground mineral mining plant, particularly a sliding plough equipment. Hydraulisches Leitungssystem fuer eine untertaegige Mineralgewinnungsanlage, insbesondere Gleithobelanlage

    Energy Technology Data Exchange (ETDEWEB)

    Dettmers, M.; Weirich, W.

    1983-01-05

    A hydraulic conduction system for a sling plough equipment assuring an utmost uniform pressure of the inner conveying trace to the coal face is described. The high-pressure main has a pressure of 300 to 400 bar. The low-pressure main is dimensioned in such a way that it exhibits a pressure drop restricted to about 5 bar at a conveying quantity of about 60 l/min and a pressure level between 100 and 200 bar. (HGOE).

  15. Hydraulic conductivity measurements with HTU at Eurajoki, Olkiluoto, drillholes OL-KR52 and OL-KR47 in 2013 and 2014

    Energy Technology Data Exchange (ETDEWEB)

    Hurmerinta, E. [Poeyry Finland Oy, Vantaa (Finland)

    2014-09-15

    As a part of the site investigations for the disposal of spent nuclear fuel, hydraulic conductivity measurements were carried out with the HTU-equipment in drillholes OL KR52 and OL KR47 on the Olkiluoto investigation site. The objective was to investigate the distribution of the hydraulic conductivity in the surrounding bedrock volume. In OL-KR52 measurements were carried out between February 2013 and April 2013 and in OL-KR47 between October 2013 and February 2014. The total length of the drillhole OL-KR52 is 427.35 m, 376.00 m of which was covered by 188 standard tests with 2 m packer separation as specified in the measurement plan. Respectively, OL-KR47 is 1008.76 m long and 312 similar tests were conducted in it covering 624.00 m of the drillhole. These numbers include one equipment test measurement near the surface in OL-KR47. Double-packer constant-head method was used throughout with nominal 200 kPa overpressure. Injection stage lasted normally 20 minutes and fall-off stage 10 minutes. The tests were often shortened if there were clear indications that the hydraulic conductivity is below the measuring range of the system. The pressure in the test section was let to stabilise at least 5 min before injection. In some test sections the test stage times were extended if longer times were needed to obtain correct results or when suited to the working schedule. Two transient (Horner and 1/Q) interpretations and one stationary-state (Moye) interpretation were made in-situ immediately after the test. The Hydraulic Testing Unit (HTU-system) is owned by Posiva Oy and it was operated by Poeyry Finland Oy in co-operation with Geopros Oy. (orig.)

  16. The Effects of Salinity and Sodium Adsorption Ratio on the Water Retention and Hydraulic Conductivity Curves of Soils From The Pampa del Tamarugal, Chile

    Science.gov (United States)

    Lagos, M. S.; Munoz, J.; Suarez, F. I.; Fierro, V.; Moreno, C.

    2015-12-01

    The Pampa del Tamarugal is located in the Atacama Desert, the most arid desert of the world. It has important reserves of groundwater, which are probably fed by infiltration coming from the Andes Mountain, with groundwater levels fluctuating between 3 and 10-70 m below the land surface. In zones where shallow groundwater exists, the capillary rise allows to have a permanently moist vadose zone, which sustain native vegetation such as the Tamarugos (Prosopis tamarugo Phil.) and Algarrobos (Prosopis alba Griseb.). The native vegetation relies on the soil moisture and on the evaporative fluxes, which are controlled by the hydrodynamic characteristics of the soils. The soils associated to the salt flats of the Pampa del Tamarugal are a mixture of sands and clays, which have high levels of sulfates, chloride, carbonates, sodium, calcium, magnesium, and potassium, with high pH and electrical conductivity, and low organic matter and cationic exchange capacity. In this research, we are interested in evaluating the impact of salinity and sodium adsorption ratio (SAR) on the hydrodynamic characteristics of the soil, i.e., water retention and hydraulic conductivity curves. Soils were collected from the Pampa del Tamarugal and brought to the laboratory for characterization. The evaporation method (HYPROP, UMS) was used to determine the water retention curve and the hydraulic conductivity curve was estimated combining the evaporation method with direct measurements using a variable head permeameter (KSAT, UMS). It was found that higher sodium concentrations increase the water retention capacity and decrease the soiĺs hydraulic conductivity. These changes occur in the moist range of the hydrodynamic characteristics. The soil's hydraulic properties have significant impact on evaporation fluxes, which is the mayor component of the water balance. Thus, it is important to quantify them and incorporate salt precipitation/dissolution effect on the hydrodynamic properties to correctly

  17. Hydraulic conductivity how subsidy in evaluation of the contaminated area in the petrochemical industry; Condutividade hidraulica como subsidio na avaliacao de area contaminada em industria petroquimica

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, Julia Brazil; Polivanov, Helena; Moraes, Patricia [Universidade Federal do Rio de Janeiro, RJ (Brazil)]. E-mail: juliabrazilsousa@yahoo.com

    2003-07-01

    The activities here described were undertaken in the scope of the Environmental Management System (EMS) of Petroflex Ind. e Com. S.A., done in cooperation with the Geosciences Institute (Instituto de Geociencias) of the UFRJ. In order to determine the hydraulic conductivity of the media in the lab, and to estimate the influence of this property on the retention of a contamination plume resulted from unsuitable disposal of industrial residues, five undisturbed samples of marine organic clay were tested. The hydraulic conductivity values obtained in laboratory vary from 10{sup -5} to 10{sup -7} cm/s. Slug tests done by the company personnel yielded results with a magnitude of 10{sup -8} cm/s. The small values of hydraulic conductivity, associated to chemical and mineralogical properties from the material, lead to the conclusion that the possibly existing contamination plume would hardly pass through the organic clay layer without having its concentration modified, since many factors provide interaction between soil and contaminant, reducing the substance concentration in fluid (water) and providing good conditions to remediation measures. (author)

  18. HYDRAULIC CONDUCTIVITY IN ENVIRONMENTAL LINERS PRODUCED WITH SANDY SOIL, CHEMICALLY STABILIZED = CONDUTIVIDADE HIDRÁULICA DE BARREIRAS DE PROTEÇÃO PRODUZIDAS COM SOLO ARENOSO ESTABILIZADO QUIMICAMENTE

    Directory of Open Access Journals (Sweden)

    José Augusto de Lollo

    2004-01-01

    Full Text Available Hydraulic conductivity of barriers produced with sandy soil (65% sand and 27% clay stabilized with lime and cement was tested. Specimens produced with compacted mixtures and tested using variable charges and total surface tests in order to determine hydraulic conductivity. Some factors vary during the tests, like the kind of aditive (lime and cement, the amount of lime and cement, cure time and exposition condition. Obtained hydraulic conductivity values were smaller than 10-9 m/s, showing values fully compatible with the intended purpose. Is also proposed a sistematic procedure to aply this techinque in simmilar situations. = Foi testada a condutividade hidráulica de barreiras de proteção ambiental produzidas com solo arenoso (65% de areia e 27% de argila estabilizado quimicamente com cal e cimento. Foram ensaiados corpos de prova das misturas compactadas usando as técnicas de ensaio de permeabilidade a carga variável e em área plena considerando os fatores tipo de estabilizante, teor de estabilizante, tempo de cura e condição de exposição. Os resultados dos ensaios de permeabilidade mostraram valores de condutividade hidráulica inferiores a 10-9 m/s, portanto compatíveis com a finalidade pretendida. É proposta uma seqüência de procedimentos a ser adotada em situações similares nas quais se pretenda aplicar esta técnica.

  19. Spatial Variability of Strontium Distribution Coefficients and Their Correlation With Hydraulic Conductivity in the Canadian Forces Base Borden Aquifer

    Science.gov (United States)

    Robin, M. J. L.; Sudicky, E. A.; Gillham, R. W.; Kachanoski, R. G.

    1991-10-01

    Distribution coefficients (Kd), defined as the ratio of the concentration of solute associated with the solids to the concentration in solution, are widely used in the prediction of reactive solute transport. With the advent of stochastic approaches to describe solute transport, there is a need to examine the spatial distribution of Kd, and its correlation with the hydraulic conductivity (K). Distribution coefficients were measured in triplicates for strontium on 1279 subsamples of cores from Canadian Forces Base Borden for which K measurements were available. The Kd values ranged from 4.4 to 29.8 mL/g, with a mean of 9.9 and standard deviation of 2.89 mL/g. The standard error on the triplicate means was 0.95 mL/g or approximately 10% of the mean. The spatial behavior of Kd and K (expressed as In (Kd) and ln (K)) was examined in three directions: horizontally along two orthogonal transects and vertically. The two variables each behaved nearly identically in the two horizontal directions, suggesting horizontal isotropy. Horizontally, ln (Kd) appeared as "white noise" suggesting that the horizontal spacing between cores (1 m) was too large to detect any self-correlation. The distribution coefficient displayed increasing power spectral density with increasing scale in the vertical direction, while In (K) showed these trends in all directions. Depending on the model used, the, correlation lengths obtained by least squares fits of the power spectra varied from 1 to 7.5 m horizontally and from 10 to 30 cm vertically for ln (K); and from 30 cm to 2 m horizontally and from 30 to 70 cm vertically for ln (Kd). The ln (Kd) values showed a significant but very weak negative overall correlation with ln (K) at the 99.95% confidence level. The cross-spectral and coherency analysis showed that the sign and degree of correlation between ln (Kd) and ln (K) depended on the scale and direction considered. The correlations in all directions and at all scales were weak, and could not

  20. Impacts of biochar concentration and particle size on hydraulic conductivity and DOC leaching of biochar-sand mixtures

    Science.gov (United States)

    Liu, Zuolin; Dugan, Brandon; Masiello, Caroline A.; Barnes, Rebecca T.; Gallagher, Morgan E.; Gonnermann, Helge

    2016-02-01

    The amendment of soil with biochar can sequester carbon and alter hydrologic properties by changing physical and chemical characteristics of soil. To understand the effect of biochar amendment on soil hydrology, we measured the hydraulic conductivity (K) of biochar-sand mixtures as well as dissolved organic carbon (DOC) in leachate. Specifically, we assessed the effects of biochar concentration and particle size on K and amount of DOC in the soil leachate. To better understand how physical properties influenced K, we also measured the skeletal density of biochars and sand, and the bulk density, the water saturation, and the porosity of biochar-sand mixtures. Our model soil was sand (0.251-0.853 mm) with biochar rates from 2 to 10 wt% (g biochar/g total soil × 100%). As biochar (concentration increased from 0 to 10 wt%, K decreased by 72 ± 3%. When biochar particle size was equal to, greater than, and less than particle size of sand, we found that biochar in different particle sizes have different effects on K. For a 2 wt% biochar rate, K decreased by 72 ± 2% when biochar particles were finer than sand particles, and decreased by 15 ± 2% when biochar particles were coarser than sand particles. When biochar and sand particle size were comparable, we observed no significant effect on K. We propose that the decrease of K through the addition of fine biochar was because finer biochar particles filled spaces between sand particles, which increased tortuosity and reduced pore throat size of the mixture. The decrease of K associated with coarser biochar was caused by the bimodal particle size distribution, resulting in more compact packing and increased tortuosity. The loss of biochar C as DOC was related to both biochar rate and particle size. The cumulative DOC loss was 1350% higher from 10 wt% biochar compared to pure sand. This large increase reflected the very small DOC yield from pure sand. In addition, DOC in the leachate decreased as biochar particle size

  1. Variations of root hydraulic conductance of Fraxinus mandshurica seedlings in different concentrations of NH4N03 solution

    Institute of Scientific and Technical Information of China (English)

    SUN Hailong; WU Chu; XU Wenjing; WANG Zhengquan

    2006-01-01

    Absorbing water from soil by roots in vascular plants is an important physiological function and plays an essential role on their water balance.The root hydraulic conductance (Lp) determined by radical water transport inside the root is a major influence on the shoot water status,plant growth,and development.However,a few studies have focused on the effect of different substances on Lp of roots,and the role of radical water transport was poorly understood.Based on the pressure-flux approach,this study used the roots of Fraxinus mandshurica seedlings with different treatments,i.e.,distilled water,NH4NO3 solution,and HgC12 to determine the effect of various substances on Lp of roots.The objectives are:1) to evaluate the difference in Lp occurred between distilled water and NH4NO3 solution with various concentrations;and 2) to examine the changes of Lp under distilled water and NH4NO3 solution with various concentrations after HgC12 treatment.The results showed that Lp of roots were 18.85×10-8 m/(s·MPa) in distilled water,31.25-34.15× 10-8 m/(s·MPa) in four NHnNO3 solutions (2,4,8 and 16 mmol/L),14.69×10-8 m/(s.MPa) in distilled water after HgC12-treated,and 9.63-13.57×10-8 m/(s·MPa)in four NH4NO3 solutions after HgC12-treated,respectively.Aquaporins play an important role in regulating water uptake and transport in roots.NH4+ and NO3- could stimulate activity of aquaporins,and Lp of roots in NH4NO3 solution was distinctly 77% higher than in distilled water.Nevertheless,Hg2+ can inhibit activity of aquaporins,and and Lp of roots decreased 22% in distilled water and 68% in NH4NO3 solution after treatment by HgC12 respectively.These evidences suggested that both Hg2+-sensitive aquaporins and ion channels existing in the protoplasm and vacuole membranes could regulate root water uptake,transport,and integral plant water balance.

  2. Transmission zero in a quantum dot with strong electron-electron interaction: Perturbative conductance calculations

    Science.gov (United States)

    Kim, Sejoong; Lee, Hyun-Woo

    2006-05-01

    A pioneering experiment [E. Schuster, E. Buks, M. Heiblum, D. Mahalu, V. Umansky, and Hadas Shtrikman, Nature 385, 417 (1997)] reported the measurement of the transmission phase of an electron traversing a quantum dot and found the intriguing feature of a sudden phase drop in the conductance valleys. Based on the Friedel sum rule for a spinless effective one-dimensional system, it has been previously argued [H.-W. Lee, Phys. Rev. Lett. 82, 2358 (1999)] that the sudden phase drop should be accompanied by the vanishing of the transmission amplitude, or transmission zero. Here we address roles of strong electron-electron interactions on the electron transport through a two-level quantum dot where one level couples with the leads much more strongly than the other level does [P. G. Silvestrov and Y. Imry, Phys. Rev. Lett. 85, 2565 (2000)]. We perform a perturbative conductance calculation with an explicit account of large charging energy and verify that the resulting conductance exhibits transmission zero, in agreement with the analysis based on the Friedel sum rule.

  3. Hydraulic conductivity measurements with HTU at Eurajoki, Olkiluoto, drillholes OL-KR19, OL-KR45 and OL-KR46 in 2009 and 2010

    Energy Technology Data Exchange (ETDEWEB)

    Haemaelaeinen, H. [Geopros Oy, Helsinki (Finland)

    2011-10-15

    As a part of the site investigations for the disposal of spent nuclear fuel, hydraulic conductivity measurements were carried out with HTU-equipment in drillholes OL-KR19, OL-KR45 and OL-KR46 at Eurajoki, Olkiluoto. The objective was to investigate the distribution of the hydraulic conductivity in the surrounding bedrock volume. Measurements were carried out during 2009 and 2010. The total length of the borehole OL-KR19 is 544,34 m, 241,80 m of which was covered by 121 standard tests with 2 m packer separation as specified in the measurement plan. Respectively, OL-KR45 is 1023,30 m long and 63 similar tests were made in it covering 126,00 m of the hole and OL-KR46 600,10 m long, 151 tests made covering 301,35 m. The measured sections are around the depths of the planned repository. Double-packer constant-head method was used throughout with nominal 200 kPa overpressure. Injection stage lasted normally 20 minutes and fall-off stage 10 minutes. The tests were often shortened if there were clear indications that the hydraulic conductivity is below the measuring range of the system. The pressure in the test section was let to stabilise at least 5 min before injection. In some test sections the test stage times were extended. Two transient (Horner and 1/Q) interpretations and one stationary- state (Moye) interpretation were made in-situ immediately after the test. The Hydraulic Testing Unit (HTU-system) is owned by Posiva Oy and it was operated by Geopros Oy. (orig.)

  4. Conductivity Modifications of Graphene by Electron Donative Organic Molecules

    Science.gov (United States)

    Masujima, Hiroaki; Mori, Takehiko; Hayamizu, Yuhei

    2017-03-01

    Graphene has been studied for the application of transparent electrodes in flexible electrical devices with semiconductor organics. Control of the charge carrier density in graphene is crucial to reduce the contact resistance between graphene and the active layer of organic semiconductor. Chemical doping of graphene is an approach to change the carrier density, where the adsorbed organic molecules donate or accept electrons form graphene. While various acceptor organic molecules have been demonstrated so far, investigation about donor molecules is still poor. In this work, we have investigated doping effect in graphene field-effect transistors functionalized by organic donor molecules such as dibenzotetrathiafulvalene (DBTTF), hexamethyltetrathiafulvalene (HMTTF), 1,5-diaminonaphthalene (DAN), and N,N,N',N'-tetramethyl-p-phenylenediamine (TMPD). Based on conductivity measurements of graphene transistors, the former three molecules do not have any significant effect to graphene transistors. However, TMPD shows effective n-type doping. The doping effect has a correlation with the level of highest occupied molecular orbital (HOMO) of each molecule, where TMPD has the highest HOMO level.

  5. Impact of simulated herbivory on water relations of aspen (Populus tremuloides) seedlings: the role of new tissue in the hydraulic conductivity recovery cycle.

    Science.gov (United States)

    Gálvez, David A; Tyree, M T

    2009-10-01

    Physiological mechanisms behind plant-herbivore interactions are commonly approached as input-output systems where the role of plant physiology is viewed as a black box. Studies evaluating impacts of defoliation on plant physiology have mostly focused on changes in photosynthesis while the overall impact on plant water relations is largely unknown. Stem hydraulic conductivity (k(h)), stem specific conductivity (k(s)), percent loss of hydraulic conductivity (PLC), CO(2) assimilation (A) and stomatal conductance (g(s)) were measured on well-irrigated 1-month-old Populus tremuloides (Michx.) defoliated and control seedlings until complete refoliation. PLC values of defoliated seedlings gradually increased during the refoliation process despite them being kept well irrigated. k(s) of defoliated seedlings gradually decreased during refoliation. PLC and k(s) values of control seedlings remained constant during refoliation. k(s) of new stems, leaf specific conductivity and A of leaves grown from new stems in defoliated and control seedlings were not significantly different, but g(s) was higher in defoliated than in control seedlings. The gradual increase of PLC and decrease of k(s) values in old stems after defoliation was unexpected under well-irrigated conditions, but appeared to have little impact on new stems formed after defoliation. The gradual loss of conductivity measured during the refoliation process under well-irrigated conditions suggests that young seedlings of P. tremuloides may be more susceptible to cavitation after herbivore damage under drought conditions.

  6. Gas exchange recovery following natural drought is rapid unless limited by loss of leaf hydraulic conductance: evidence from an evergreen woodland.

    Science.gov (United States)

    Skelton, Robert P; Brodribb, Timothy J; McAdam, Scott A M; Mitchell, Patrick J

    2017-09-01

    Drought can cause major damage to plant communities, but species damage thresholds and postdrought recovery of forest productivity are not yet predictable. We used an El Niño drought event as a natural experiment to test whether postdrought recovery of gas exchange could be predicted by properties of the water transport system, or if metabolism, primarily high abscisic acid concentration, might delay recovery. We monitored detailed physiological responses, including shoot sapflow, leaf gas exchange, leaf water potential and foliar abscisic acid (ABA), during drought and through the subsequent rehydration period for a sample of eight canopy and understory species. Severe drought caused major declines in leaf water potential, elevated foliar ABA concentrations and reduced stomatal conductance and assimilation rates in our eight sample species. Leaf water potential surpassed levels associated with incipient loss of leaf hydraulic conductance in four species. Following heavy rainfall gas exchange in all species, except those trees predicted to have suffered hydraulic impairment, recovered to prestressed rates within 1 d. Recovery of plant gas exchange was rapid and could be predicted by the hydraulic safety margin, providing strong support for leaf vulnerability to water deficit as an index of damage under natural drought conditions. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

  7. Formulation of soil hydraulic conductivity from water retention curve, based on data inversion results, interpreted in terms of tortuosity, connectivity and flow turbulence.

    Science.gov (United States)

    du Gardin, Béryl; Lucas, Yves

    2014-05-01

    In order to refine hydraulic conductivity determination from soil water retention curve, we calculated the correcting factors, by data inversion, using a generalised formulation issued from Burdine or Mualem hydraulic conductivity. These formulations use the laminar flow, obeying Poiseuille law, through a bundle of cylinders of different radii, and correcting factors traducing the gap with real flow and real soil geometry. A general correcting factor is supposed to be proportional to water content, with an exponent a. An inner correcting factor is a function of pore size and/or water content and is inside the integral. We did not presuppose any analytical form for this inner correcting function. We used soil data obtained from clayey Amazonian tropical ferralsols composed of around 7/8 of clay fraction and fine silt (mainly kaolinite with some gibbsite and goethite) and 1/8 of coarse sand (quartz and kaolinite aggregates), with 0,2 to 1,5 % organic carbon content. Data were obtained using three different techniques : high pressurized water extraction disposal, evaporation experiment (Wind method) and in situ infiltration. The explored pore size domain was very large, ranging from 2 micrometers to 2 mm, completed by some data around 0,1 micrometer, so three to four orders of magnitude. We precised pore distribution in the range from 4 nm to 2 micrometers with mercury injection porosimetry corrected from drying effects. The pore distribution is bimodal, with a very small pore volume around 0,25 micrometer pore size. Such pore distribution allows observing separately the effects of pore size and water content on hydraulic conductivity, as water content is not a regularly increasing function of largest filled pores size. The results showed that a general correcting factor as an exponent of water content over all the described domain is inappropriate, as we encountered the smallest spreading of the inner correcting function when the exponent a is zero. The general

  8. Hydraulic Conductivity Measurements with HTU at Eurajoki, Olkiluoto, Boreholes OL-KR16, 16B, 17, 17B, 18 and 18B, Year 2004

    Energy Technology Data Exchange (ETDEWEB)

    Haemaelaeinen, H.

    2005-07-01

    As a part of the site investigations for the disposal of spent nuclear fuel, hydraulic con- ductivity measurements were carried out in boreholes OL-KR16, 16B, 17, 17 B, 18 and 18B at Eurajoki, Olkiluoto. The objective was to investigate the distribution of the hydraulic conductivity in the surrounding bedrock volume. Measurements were carried out during spring-summer 2004. The total lengths of the boreholes are: OL-KR16 170,20 m, OL-KR17 157,13 m and OL-KR18 125,49 m. Corresponding B-holes are around 45 m deep, parallel and adjacent to their 'parent' holes so representing the cased sections of them. The conbined measurable length of the holes is about 453,57 m, of which 429,15 m was covered with 217 standard tests at 2 m packer separation as specified in the research plan. 246 tests were initiated, but some had to be cancelled due to errors or unsuitable control parameters. Double-packer constant-head method was used throughout with nominal 200 kPa overpressure. Injection stage lasted normally 20 minutes and fall-off stage 10 minutes. The tests were often shortened if there were clear indications that the hydraulic conductivity is below the measuring range of the system. The pressure in the test section was let to stabilise at least 5 min before injection. In some test sections the stabilisation, injection or fall-off stage lasted several hours. Two transient (Horner and 1/Q) interpretations and one stationary-state (Moye) interpretation were made in-situ immediately after the test. The Hydraulic Testing Unit (HTU-system) is owned by Posiva Oy and it was operated by Geopros Oy. (orig.)

  9. Improvement of diesel engine performance by hydraulically powered electronic control (mechatronics) system. Hakuyo diesel kikan no mechatronics system ni yoru seino kojo

    Energy Technology Data Exchange (ETDEWEB)

    Sonoda, K.; Nakamura, Y.; Kajima, T.; Sato, S.; Fujii, T.; Tobe, Y. (Kawasaki Heavy Industries, Ltd., Tokyo (Japan))

    1992-07-20

    This paper describes new hydraulically-actuated mechanisms for both fuel injection and inlet/exhaust valve operation of diesel engines through solenoid valves, which obviate the conventional cam-driven system. These mechanisms were integrated with an electronic control unit also developed in this study and they were mounted as a mechatronics system'' on a power-increased single-cylinder engine. This mechatronics system was mainly composed of an injection control. boost and accumulation component, an inlet and exhaust valve control component, a solenoid valve, an electronic control equipment, a hydraulic power unit, and a maneuvering unit. The verification test was carried out for the improvement of diesel engine performance by the hydraulically powered mechatronics system. As a result, it was proved not only that these mechanisms provide stable operating characteristics over a wide range of conditions, but also that the electronic control system allows accurate, smooth response. 3 refs., 23 figs., 2 tabs.

  10. Changes of Root Hydraulic Conductivity and Root/Shoot Ratio of Durum Wheat and Barley in Relation to Nitrogen Availability and Mercury Exposure

    Directory of Open Access Journals (Sweden)

    Giovanna Angelino

    2011-02-01

    Full Text Available The aim of this research was to verify, on whole plant level and during all the plant cycle, the hypothesis that nitrogen deficiency reduces root hydraulic conductivity through the water channels (aquaporins activity, and that the plant reacts by changing root/shoot ratio. Root hydraulic conductivity, plant growth, root/shoot ratio and plant water status were assessed for durum wheat (Triticum durum Desf. and barley (Hordeum vulgare L., as influenced by nitrogen availability and HgCl2 treatment. On both species during the plant cycle, nitrogen deficiency induced lower root hydraulic conductivity (-49 and -66% respectively for barley and wheat and lower plant growth. On wheat was also observed cycle delay, lower plant nitrogen content, but not lower leaf turgor pressure and epidermic cell dimension. The lower plant growth was due to lower plant dimension and lower tillering. Root /shoot ratio was always higher for nitrogen stressed plants, whether on dry matter or on surface basis. This was due to lower effect of nitrogen stress on root growth than on shoot growth. On wheat HgCl2 treatment determined lower plant growth, and more than nitrogen stress, cycle delay and higher root/shoot ratio. The mercury, also, induced leaf rolling, lower turgor pressure, lower NAR, higher root cell wall lignification and lower epidermic cell number per surface unity. In nitrogen fertilized plants root hydraulic conductivity was always reduced by HgCl2 treatment (-61 and 38%, respectively for wheat and barley, but in nitrogen unfertilized plants this effect was observed only during the first plant stages. This effect was higher during shooting and caryopsis formation, lower during tillering. It is concluded that barley and durum wheat react to nitrogen deficiency and HgCl2 treatment by increasing the root/shoot ratio, to compensate water stress due to lower water root conductivity probably induced by lower aquaporin synthesis or inactivation. However, this

  11. Leaf hydraulic conductance declines in coordination with photosynthesis, transpiration and leaf water status as soybean leaves age regardless of soil moisture.

    Science.gov (United States)

    Locke, Anna M; Ort, Donald R

    2014-12-01

    Photosynthesis requires sufficient water transport through leaves for stomata to remain open as water transpires from the leaf, allowing CO2 to diffuse into the leaf. The leaf water needs of soybean change over time because of large microenvironment changes over their lifespan, as leaves mature in full sun at the top of the canopy and then become progressively shaded by younger leaves developing above. Leaf hydraulic conductance (K(leaf)), a measure of the leaf's water transport capacity, can often be linked to changes in microenvironment and transpiration demand. In this study, we tested the hypothesis that K(leaf) would decline in coordination with transpiration demand as soybean leaves matured and aged. Photosynthesis (A), stomatal conductance (g(s)) and leaf water potential (Ψ(leaf)) were also measured at various leaf ages with both field- and chamber-grown soybeans to assess transpiration demand. K(leaf) was found to decrease as soybean leaves aged from maturity to shading to senescence, and this decrease was strongly correlated with midday A. Decreases in K(leaf) were further correlated with decreases in g(s), although the relationship was not as strong as that with A. Separate experiments investigating the response of K(leaf) to drought demonstrated no acclimation of K(leaf) to drought conditions to protect against cavitation or loss of g(s) during drought and confirmed the effect of leaf age in K(leaf) observed in the field. These results suggest that the decline of leaf hydraulic conductance as leaves age keeps hydraulic supply in balance with demand without K(leaf)becoming limiting to transpiration water flux.

  12. Leaf hydraulic conductance declines in coordination with photosynthesis, transpiration and leaf water status as soybean leaves age regardless of soil moisture

    Science.gov (United States)

    Locke, Anna M.; Ort, Donald R.

    2014-01-01

    Photosynthesis requires sufficient water transport through leaves for stomata to remain open as water transpires from the leaf, allowing CO2 to diffuse into the leaf. The leaf water needs of soybean change over time because of large microenvironment changes over their lifespan, as leaves mature in full sun at the top of the canopy and then become progressively shaded by younger leaves developing above. Leaf hydraulic conductance (K leaf), a measure of the leaf’s water transport capacity, can often be linked to changes in microenvironment and transpiration demand. In this study, we tested the hypothesis that K leaf would decline in coordination with transpiration demand as soybean leaves matured and aged. Photosynthesis (A), stomatal conductance (g s) and leaf water potential (Ψleaf) were also measured at various leaf ages with both field- and chamber-grown soybeans to assess transpiration demand. K leaf was found to decrease as soybean leaves aged from maturity to shading to senescence, and this decrease was strongly correlated with midday A. Decreases in K leaf were further correlated with decreases in g s, although the relationship was not as strong as that with A. Separate experiments investigating the response of K leaf to drought demonstrated no acclimation of K leaf to drought conditions to protect against cavitation or loss of g s during drought and confirmed the effect of leaf age in K leaf observed in the field. These results suggest that the decline of leaf hydraulic conductance as leaves age keeps hydraulic supply in balance with demand without K leaf becoming limiting to transpiration water flux. PMID:25281701

  13. Thermal conductivity and electron-phonon relaxation in a metal heated by a subpicosecond laser pulse

    Science.gov (United States)

    Petrov, Yu. V.; Anisimov, S. I.

    2006-06-01

    This paper discusses the initial stages of the interaction of subpicosecond laser pulses with metallic targets: the absorption of light, energy transport by electronic thermal conductivity, and electron-phonon relaxation. It is shown that, with moderate surface energy density, hydrodynamic motion begins after the electronic and lattice temperatures equalize. A connection is established between the energy exchange rate between the electrons and the lattice and the electronic thermal conductivity (an analog of the Wiedemann-Franz law).

  14. Electronic conduction in polymers, carbon nanotubes and graphene.

    Science.gov (United States)

    Kaiser, Alan B; Skákalová, Viera

    2011-07-01

    In the years since the discovery of organic polymers that exhibited electrical conductivities comparable to some metals, other novel carbon-based conductors have been developed, including carbon nanotubes and graphene (monolayers of carbon atoms). In this critical review, we discuss the common features and the differences in the conduction mechanisms observed in these carbon-based materials, which range from near ballistic and conventional metallic conduction to fluctuation-assisted tunnelling, variable-range hopping and more exotic mechanisms. For each category of material, we discuss the dependence of conduction on the morphology of the sample. The presence of heterogeneous disorder is often particularly important in determining the overall behaviour, and can lead to surprisingly similar conduction behaviour in polymers, carbon nanotube networks and chemically-derived graphene (122 references).

  15. Reconfigurable electronics using conducting metal-organic frameworks

    Energy Technology Data Exchange (ETDEWEB)

    Allendorf, Mark D.; Talin, Albert Alec; Leonard, Francois; Stavila, Vitalie

    2017-07-18

    A device including a porous metal organic framework (MOF) disposed between two terminals, the device including a first state wherein the MOF is infiltrated by a guest species to form an electrical path between the terminals and a second state wherein the electrical conductivity of the MOF is less than the electrical conductivity in the first state. A method including switching a porous metal organic framework (MOF) between two terminals from a first state wherein a metal site in the MOF is infiltrated by a guest species that is capable of charge transfer to a second state wherein the MOF is less electrically conductive than in the first state.

  16. Modification of Fluoropolymer Surfaces with Electronically Conductive Polymers

    Science.gov (United States)

    1993-06-01

    CI0 4)3. Polyaniline was synthesized by mixing equal volumes of a solution that was 0.25 M in ammonium persulfate and a solution that was 0.5 M in...31 Conductive polymers, polypyrrole , lithography 16. PRICE CODE 17. SECURITY CLASSIFICATION 18. SECURITY CLASSIFICATION 19. SECURITY CLASSIFICATION...surface. Fortunately, conductive polymers such as polypyrrole adhere quite well to many substrates, including nylon, polycarbonate, cellulosics

  17. Effects of spatial confinement on conduction electrons in semiconductor nanostructures

    NARCIS (Netherlands)

    Germeau, Alexander

    2003-01-01

    Semiconductor nanostructures show electrical and optical properties which can be very different from bulk semiconductors. The various effects that occur due to the spatial confinement of electrons in such structures are of scientific importance. In addition, semiconductor nanostructures are very pro

  18. Failure modes of conducting yarns in electronic-textile applications

    NARCIS (Netherlands)

    Kok, M. de; Vries, H. de; Pacheco, K.; Heck, G. van

    2015-01-01

    Integration of electronic functionalities into textiles adds to the value of textiles. It allows measuring, detecting, actuating and treating or communicating with a body or object. These added values can render the smart textiles very useful, fun, supporting, protecting or even lifesaving. It is, h

  19. Failure modes of conducting yarns in electronic-textile applications

    NARCIS (Netherlands)

    Kok, M. de; Vries, H. de; Pacheco, K.; Heck, G. van

    2015-01-01

    Integration of electronic functionalities into textiles adds to the value of textiles. It allows measuring, detecting, actuating and treating or communicating with a body or object. These added values can render the smart textiles very useful, fun, supporting, protecting or even lifesaving. It is,

  20. Variable conductivity and embolism in roots, trunks and branches of tree species growing under future atmospheric CO2 concentration (DUKE FACE site): impacts on whole-plant hydraulic performance and carbon assimilation

    Science.gov (United States)

    domec, J.; Palmroth, S.; Oren, R.; Johnson, D. M.; Ward, E. J.; McCulloh, K.; Gonzalez, C.; Warren, J.

    2013-12-01

    Anatomical and physiological acclimation to water stress of the tree hydraulic system involves tradeoffs between maintenance of stomatal conductance and loss of hydraulic conductivity, with short-term impacts on photosynthesis and long-term consequences to survival and growth. Here we study the role of variations in root, trunk and branch maximum hydraulic specific conductivity (Ks-max) under high and low soil moisture in determining whole-tree hydraulic conductance (Ktree) and in mediating stomatal control of gas exchange in loblolly pine trees growing under ambient and elevated CO2 (CO2a and CO2e). We hypothesized that Ktree would adjust to CO2e, through an increase in root and branch Ks-max in response to anatomical adjustments. Embolism in roots explained the loss of Ktree and therefore indirectly constituted a hydraulic signal involved in stomatal regulation and in the reduction of canopy conductance and carbon assimilation. Across roots, trunk and branches, the increase in Ks-max was associated with a decrease resistance to drought, a consequence of structural acclimation such as larger conduits and lower wood density. In loblolly pine, higher xylem dysfunction under CO2e might impact tree performance in a future climate when increased evaporative demand could cause a greater loss of hydraulic function. The results contributed to our knowledge of the physiological and morphological mechanisms underpinning the responses of tree species to drought and more generally to global change.

  1. Measurement of field-saturated hydraulic conductivity on fractured rock outcrops near Altamura (Southern Italy) with an adjustable large ring infiltrometer

    Science.gov (United States)

    Caputo, M.C.; de Carlo, L.; Masciopinto, C.; Nimmo, J.R.

    2010-01-01

    Up to now, field studies set up to measure field-saturated hydraulic conductivity to evaluate contamination risks, have employed small cylinders that may not be representative of the scale of measurements in heterogeneous media. In this study, a large adjustable ring infiltrometer was designed to be installed on-site directly on rock to measure its field-saturated hydraulic conductivity. The proposed device is inexpensive and simple to implement, yet also very versatile, due to its large adjustable diameter that can be fixed on-site. It thus allows an improved representation of the natural system's heterogeneity, while also taking into consideration irregularities in the soil/rock surface. The new apparatus was tested on an outcrop of karstic fractured limestone overlying the deep Murge aquifer in the South of Italy, which has recently been affected by untreated sludge disposal, derived from municipal and industrial wastewater treatment plants. The quasi-steady vertical flow into the unsaturated fractures was investigated by measuring water levels during infiltrometer tests. Simultaneously, subsurface electrical resistivity measurements were used to visualize the infiltration of water in the subsoil, due to unsaturated water flow in the fractures. The proposed experimental apparatus works well on rock outcrops, and allows the repetition of infiltration tests at many locations in order to reduce model uncertainties in heterogeneous media. ?? 2009 Springer-Verlag.

  2. Hydraulic conductance as well as nitrogen accumulation plays a role in the higher rate of leaf photosynthesis of the most productive variety of rice in Japan

    Science.gov (United States)

    Taylaran, Renante D.; Adachi, Shunsuke; Ookawa, Taiichiro; Usuda, Hideaki; Hirasawa, Tadashi

    2011-01-01

    An indica variety Takanari is known as one of the most productive rice varieties in Japan and consistently produces 20–30% heavier dry matter during ripening than Japanese commercial varieties in the field. The higher rate of photosynthesis of individual leaves during ripening has been recognized in Takanari. By using pot-grown plants under conditions of minimal mutual shading, it was confirmed that the higher rate of leaf photosynthesis is responsible for the higher dry matter production after heading in Takanari as compared with a japonica variety, Koshihikari. The rate of leaf photosynthesis and shoot dry weight became larger in Takanari after the panicle formation and heading stages, respectively, than in Koshihikari. Roots grew rapidly in the panicle formation stage until heading in Takanari compared with Koshihikari. The higher rate of leaf photosynthesis in Takanari resulted not only from the higher content of leaf nitrogen, which was caused by its elevated capacity for nitrogen accumulation, but also from higher stomatal conductance. When measured under light-saturated conditions, stomatal conductance was already decreased due to the reduction in leaf water potential in Koshihikari even under conditions of a relatively small difference in leaf–air vapour pressure difference. In contrast, the higher stomatal conductance was supported by the maintenance of higher leaf water potential through the higher hydraulic conductance in Takanari with the larger area of root surface. However, no increase in root hydraulic conductivity was expected in Takanari. The larger root surface area of Takanari might be a target trait in future rice breeding for increasing dry matter production. PMID:21527630

  3. Hydraulic conductance as well as nitrogen accumulation plays a role in the higher rate of leaf photosynthesis of the most productive variety of rice in Japan.

    Science.gov (United States)

    Taylaran, Renante D; Adachi, Shunsuke; Ookawa, Taiichiro; Usuda, Hideaki; Hirasawa, Tadashi

    2011-07-01

    An indica variety Takanari is known as one of the most productive rice varieties in Japan and consistently produces 20-30% heavier dry matter during ripening than Japanese commercial varieties in the field. The higher rate of photosynthesis of individual leaves during ripening has been recognized in Takanari. By using pot-grown plants under conditions of minimal mutual shading, it was confirmed that the higher rate of leaf photosynthesis is responsible for the higher dry matter production after heading in Takanari as compared with a japonica variety, Koshihikari. The rate of leaf photosynthesis and shoot dry weight became larger in Takanari after the panicle formation and heading stages, respectively, than in Koshihikari. Roots grew rapidly in the panicle formation stage until heading in Takanari compared with Koshihikari. The higher rate of leaf photosynthesis in Takanari resulted not only from the higher content of leaf nitrogen, which was caused by its elevated capacity for nitrogen accumulation, but also from higher stomatal conductance. When measured under light-saturated conditions, stomatal conductance was already decreased due to the reduction in leaf water potential in Koshihikari even under conditions of a relatively small difference in leaf-air vapour pressure difference. In contrast, the higher stomatal conductance was supported by the maintenance of higher leaf water potential through the higher hydraulic conductance in Takanari with the larger area of root surface. However, no increase in root hydraulic conductivity was expected in Takanari. The larger root surface area of Takanari might be a target trait in future rice breeding for increasing dry matter production.

  4. Estimation of the hydraulic conductivity of a two-dimensional fracture network using effective medium theory and power-law averaging

    Science.gov (United States)

    Zimmerman, R. W.; Leung, C. T.

    2009-12-01

    Most oil and gas reservoirs, as well as most potential sites for nuclear waste disposal, are naturally fractured. In these sites, the network of fractures will provide the main path for fluid to flow through the rock mass. In many cases, the fracture density is so high as to make it impractical to model it with a discrete fracture network (DFN) approach. For such rock masses, it would be useful to have recourse to analytical, or semi-analytical, methods to estimate the macroscopic hydraulic conductivity of the fracture network. We have investigated single-phase fluid flow through generated stochastically two-dimensional fracture networks. The centers and orientations of the fractures are uniformly distributed, whereas their lengths follow a lognormal distribution. The aperture of each fracture is correlated with its length, either through direct proportionality, or through a nonlinear relationship. The discrete fracture network flow and transport simulator NAPSAC, developed by Serco (Didcot, UK), is used to establish the “true” macroscopic hydraulic conductivity of the network. We then attempt to match this value by starting with the individual fracture conductances, and using various upscaling methods. Kirkpatrick’s effective medium approximation, which works well for pore networks on a core scale, generally underestimates the conductivity of the fracture networks. We attribute this to the fact that the conductances of individual fracture segments (between adjacent intersections with other fractures) are correlated with each other, whereas Kirkpatrick’s approximation assumes no correlation. The power-law averaging approach proposed by Desbarats for porous media is able to match the numerical value, using power-law exponents that generally lie between 0 (geometric mean) and 1 (harmonic mean). The appropriate exponent can be correlated with statistical parameters that characterize the fracture density.

  5. Improving the use of the fallout radionuclide 7Be as a sediment tracer by incorporating the hydraulic conductivity in the conversion model

    Science.gov (United States)

    Ryken, Nick; Al-Barri, Bashar; Blake, Will; Taylor, Alex; Boeckx, Pascal; Verdoodt, Ann

    2016-04-01

    There is growing interest in the application of the natural fallout radionuclide 7Be as a soil erosion and sediment tracer. Development of robust datasets is, however, hampered by unquantified spatial variability in its distribution within the surface soil. Models that convert 7Be inventory measurements to soil erosion estimates are all based on the observed depth distribution of 7Be, described by the relaxation mass depth (h0) parameter. Previous work, however, has not considered potential spatial variation in h0 linked to variability in soil physical properties, which could have major implications for the reliability of soil erosion estimates. This work addresses the close relation between infiltration rate and the 7Be depth distribution. During a laboratory rainfall simulation experiment, water spiked with stable 9Be was used to study the variability in 9Be depth distribution for eight compacted and eight non-compacted natural undisturbed soil cores, whereby 9Be was used as a substitute for 7Be. X-ray Computed Tomography (CT) scans were used to characterize the porosity of both groups, showing significant lower, strongly horizontally oriented, total porosity of the compacted soil cores. The average saturated hydraulic conductivity (ksat) of the different groups was 0.89 m day-1 and 17 m day-1 for the compacted and the non-compacted samples respectively. This physical compaction resulted in a clear distinction in 9Be depth distribution between both groups. With an average h0 of 4.66 ± 1.1 kg m-2, 9Be penetrated deeper in the non-compacted soil cores, while the compacted cores showed an average h0 of 2.42 ± 0.26 kg m-2. The reported h0 values at the former site were also characterized by a larger coefficient of variation (24%) than those at the latter site (11%), similar to the variations in soil structure observed by the CT-scans. Furthermore, the correlation between the hydraulic conductivity and the 9Be depth distribution is under investigation by

  6. Electronically conductive polymer binder for lithium-ion battery electrode

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Gao; Xun, Shidi; Battaglia, Vincent S.; Zheng, Honghe

    2017-05-16

    A family of carboxylic acid group containing fluorene/fluorenon copolymers is disclosed as binders of silicon particles in the fabrication of negative electrodes for use with lithium ion batteries. These binders enable the use of silicon as an electrode material as they significantly improve the cycle-ability of silicon by preventing electrode degradation over time. In particular, these polymers, which become conductive on first charge, bind to the silicon particles of the electrode, are flexible so as to better accommodate the expansion and contraction of the electrode during charge/discharge, and being conductive promote the flow battery current.

  7. Highly Confined Electronic and Ionic Conduction in Oxide Heterostructures

    DEFF Research Database (Denmark)

    Pryds, Nini

    2015-01-01

    . “Enhancement of the chemical stability in confined δ-Bi2O3”. Nature Materials (2015) doi:10.1038/nmat4266 [2] Y. Z. Chen et al. “A high-mobility two-dimensional electron gas at the spinel/perovskite interface of γ-Al2O3/SrTiO3”. Nature Commun. 4, 1371 (2013) [3] Y. Z. Chen et al. “Creation of High Mobility Two...

  8. Probing radiation damage by alternated current conductivity as a method to characterize electron hopping conduction in DNA molecules

    Energy Technology Data Exchange (ETDEWEB)

    Gomes, Paulo J.; Coelho, Margarida; Antonio Ribeiro, Paulo; Raposo, Maria [CEFITEC, Departamento de Fisica, Faculdade de Ciencias e Tecnologia, FCT, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Dionisio, Madalena [REQUIMTE, Departamento de Quimica, Faculdade de Ciencias e Tecnologia, FCT, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal)

    2012-09-17

    Analysis of AC electrical conductivity of deoxyribonucleic acid (DNA) thin films, irradiated with ultraviolet (UV) light, revealed that electrical conduction arises from DNA chain electron hopping between base-pairs and phosphate groups. The hopping distance calculated from correlated barrier hopping model equals the distance between DNA base-pairs, which is consistent with the loss of conductivity with irradiation time arising from a decrease in phosphates groups. In the high frequency regime, at a given frequency, real part of conductivity strongly depends on irradiation time particularly for low dose levels suggesting the use of DNA based films for UV radiation sensors.

  9. Estimation of groundwater flow directions and the tensor of hydraulic conductivity in crystalline massif rocks using information from surface structural geology and mining exploration boreholes

    Science.gov (United States)

    Florez, C.; Romero, M. A.; Ramirez, M. I.; Monsalve, G.

    2013-05-01

    In the elaboration of a hydrogeological conceptual model in regions of mining exploration where there is significant presence of crystalline massif rocks., the influence of physical and geometrical properties of rock discontinuities must be evaluated. We present the results of a structural analysis of rock discontinuities in a region of the Central Cordillera of Colombia (The upper and middle Bermellon Basin) in order to establish its hydrogeological characteristics for the improvement of the conceptual hydrogeological model for the region. The geology of the study area consists of schists with quartz and mica and porphyritic rocks, in a region of high slopes with a nearly 10 m thick weathered layer. The main objective of this research is to infer the preferential flow directions of groundwater and to estimate the tensor of potential hydraulic conductivity by using surface information and avoiding the use of wells and packer tests. The first step of our methodology is an analysis of drainage directions to detect patterns of structural controls in the run-off; after a field campaign of structural data recollection, where we compile information of strike, dip, continuity, spacing, roughness, aperture and frequency, we built equal area hydro-structural polar diagrams that indicate the potential directions for groundwater flow. These results are confronted with records of Rock Quality Designation (RQD) that have been systematically taken from several mining exploration boreholes in the area of study. By using all this information we estimate the potential tensor of hydraulic conductivity from a cubic law, obtaining the three principal directions with conductivities of the order of 10-5 and 10-6 m/s; the more conductive joint family has a NE strike with a nearly vertical dip.

  10. Electronically conductive polymer binder for lithium-ion battery electrode

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Gao; Battaglia, Vincent S.; Park, Sang -Jae

    2015-10-06

    A family of carboxylic acid groups containing fluorene/fluorenon copolymers is disclosed as binders of silicon particles in the fabrication of negative electrodes for use with lithium ion batteries. Triethyleneoxide side chains provide improved adhesion to materials such as, graphite, silicon, silicon alloy, tin, tin alloy. These binders enable the use of silicon as an electrode material as they significantly improve the cycle-ability of silicon by preventing electrode degradation over time. In particular, these polymers, which become conductive on first charge, bind to the silicon particles of the electrode, are flexible so as to better accommodate the expansion and contraction of the electrode during charge/discharge, and being conductive promote the flow battery current.

  11. Electronically conductive polymer binder for lithium-ion battery electrode

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Gao; Xun, Shidi; Battaglia, Vincent S.; Zheng, Honghe; Wu, Mingyan

    2015-07-07

    A family of carboxylic acid groups containing fluorene/fluorenon copolymers is disclosed as binders of silicon particles in the fabrication of negative electrodes for use with lithium ion batteries. Triethyleneoxide side chains provide improved adhesion to materials such as, graphite, silicon, silicon alloy, tin, tin alloy. These binders enable the use of silicon as an electrode material as they significantly improve the cycle-ability of silicon by preventing electrode degradation over time. In particular, these polymers, which become conductive on first charge, bind to the silicon particles of the electrode, are flexible so as to better accommodate the expansion and contraction of the electrode during charge/discharge, and being conductive promote the flow battery current.

  12. Electronically conductive polymer binder for lithium-ion battery electrode

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Gao; Xun, Shidi; Battaglia, Vincent S.; Zheng, Honghe; Wu, Mingyan

    2017-08-01

    A family of carboxylic acid groups containing fluorene/fluorenon copolymers is disclosed as binders of silicon particles in the fabrication of negative electrodes for use with lithium ion batteries. Triethyleneoxide side chains provide improved adhesion to materials such as, graphite, silicon, silicon alloy, tin, tin alloy. These binders enable the use of silicon as an electrode material as they significantly improve the cycle-ability of silicon by preventing electrode degradation over time. In particular, these polymers, which become conductive on first charge, bind to the silicon particles of the electrode, are flexible so as to better accommodate the expansion and contraction of the electrode during charge/discharge, and being conductive promote the flow battery current.

  13. Effects of age-related increases in sapwood area, leaf area, and xylem conductivity on height-related hydraulic costs in two contrasting coniferous species

    Science.gov (United States)

    Jean-Christophe Domec; Barbara Lachenbruch; Michele L. Pruyn; Rachel Spicer

    2012-01-01

    Introduction: Knowledge of vertical variation in hydraulic parameters would improve our understanding of individual trunk functioning and likely have important implications for modeling water movement to the leaves. Specifically, understanding how foliage area (Al), sapwood area (As), and hydraulic specific...

  14. Thermal computations for electronics conductive, radiative, and convective air cooling

    CERN Document Server

    Ellison, Gordon

    2010-01-01

    IntroductionPrimary mechanisms of heat flowConductionApplication example: Silicon chip resistance calculationConvectionApplication example: Chassis panel cooled by natural convectionRadiationApplication example: Chassis panel cooled only by radiation 7Illustrative example: Simple thermal network model for a heat sinked power transistorIllustrative example: Thermal network circuit for a printed circuit boardCompact component modelsIllustrative example: Pressure and thermal circuits for a forced air cooled enclosureIllustrative example: A single chip package on a printed circuit board-the proble

  15. Laboratory-Measured and Property-Transfer Modeled Saturated Hydraulic Conductivity of Snake River Plain Aquifer Sediments at the Idaho National Laboratory, Idaho

    Science.gov (United States)

    Perkins, Kim S.

    2008-01-01

    Sediments are believed to comprise as much as 50 percent of the Snake River Plain aquifer thickness in some locations within the Idaho National Laboratory. However, the hydraulic properties of these deep sediments have not been well characterized and they are not represented explicitly in the current conceptual model of subregional scale ground-water flow. The purpose of this study is to evaluate the nature of the sedimentary material within the aquifer and to test the applicability of a site-specific property-transfer model developed for the sedimentary interbeds of the unsaturated zone. Saturated hydraulic conductivity (Ksat) was measured for 10 core samples from sedimentary interbeds within the Snake River Plain aquifer and also estimated using the property-transfer model. The property-transfer model for predicting Ksat was previously developed using a multiple linear-regression technique with bulk physical-property measurements (bulk density [pbulk], the median particle diameter, and the uniformity coefficient) as the explanatory variables. The model systematically underestimates Ksat,typically by about a factor of 10, which likely is due to higher bulk-density values for the aquifer samples compared to the samples from the unsaturated zone upon which the model was developed. Linear relations between the logarithm of Ksat and pbulk also were explored for comparison.

  16. Soft capacitor fibers using conductive polymers for electronic textiles

    Science.gov (United States)

    Gu, Jian Feng; Gorgutsa, Stephan; Skorobogatiy, Maksim

    2010-11-01

    A novel, highly flexible, conductive polymer-based fiber with high electric capacitance is reported. In its cross section the fiber features a periodic sequence of hundreds of conductive and isolating plastic layers positioned around metallic electrodes. The fiber is fabricated using the fiber drawing method, where a multi-material macroscopic preform is drawn into a sub-millimeter capacitor fiber in a single fabrication step. Several kilometers of fibers can be obtained from a single preform with fiber diameters ranging between 500 and 1000 µm. A typical measured capacitance of our fibers is 60-100 nF m-1 and it is independent of the fiber diameter. Analysis of the fiber frequency response shows that in its simplest interrogation mode the capacitor fiber has a transverse resistance of 5 kΩ m L-1, which is inversely proportional to the fiber length L and is independent of the fiber diameter. Softness of the fiber materials, the absence of liquid electrolyte in the fiber structure, ease of scalability to large production volumes and high capacitance of our fibers make them interesting for various smart textile applications ranging from distributed sensing to energy storage.

  17. Soft capacitor fibers using conductive polymers for electronic textiles

    CERN Document Server

    Gu, Jian Feng; Skorobogatiy, Maksim

    2010-01-01

    A novel, highly flexible, conductive polymer-based fiber with high electric capacitance is reported. In its crossection the fiber features a periodic sequence of hundreds of conductive and isolating plastic layers positioned around metallic electrodes. The fiber is fabricated using fiber drawing method, where a multi-material macroscopic preform is drawn into a sub-millimeter capacitor fiber in a single fabrication step. Several kilometres of fibers can be obtained from a single preform with fiber diameters ranging between 500um -1000um. A typical measured capacitance of our fibers is 60-100 nF/m and it is independent of the fiber diameter. For comparison, a coaxial cable of the comparable dimensions would have only ~0.06nF/m capacitance. Analysis of the fiber frequency response shows that in its simplest interrogation mode the capacitor fiber has a transverse resistance of 5 kOhm/L, which is inversely proportional to the fiber length L and is independent of the fiber diameter. Softness of the fiber materials...

  18. Hydraulic conductivity tests on damaged geosynthetic clay liners%带缺陷膨润土防水毯的渗透试验

    Institute of Scientific and Technical Information of China (English)

    何俊; 肖衡林; 孔祥怡

    2011-01-01

    分别以自来水和0.05 mol/L的CaCl2溶液作为渗滤溶液研究带缺陷膨润土防水毯(GCL)的渗透性能.试验结果表明:自来水渗滤时,GCL的渗透系数随着缺陷直径的增大而增大,缺陷直径达11mm时缺陷不能完全愈合,致使渗透系数超过1×10-9m/s.CaCl2溶液渗滤时,随着离子交换作用的进行,渗透系数随孔隙体积流量的增大有增大的趋势;缺陷直径小于5mm时GCL具有一定的自愈能力,但增至7mm时缺陷不能愈合,溶液和缺陷的共同作用使得GCL的防渗性能很差.%The permeability of damaged geosynthetic clay liner (GCL) was studied fay using the tap water and the 0.05mol/L CaCl2 solution as the percolating liquid, respectively. The results show that for the taper water, the hydraulic conductivity of the damaged GCL increases with the increase of hole diameter. The damaged GCL can not self-heal when the hole diameter reaches 11mm, and the hydraulic conductivity will be larger than 1 × 10-9 m/s. For the 0.05mol/L CaCl2 solution, the hydraulic conductivity of the damaged GCL increases with the increase of pore volume flows due to ion exchange. The damaged GCL have certain self-healing capacity when the hole diameter is less than 5 mm and can not self-heal when the hole diameter reaches 7 mm. The combined action of the solution and the defect results in poor permeability performance of the damaged GCL.

  19. Experiment study of forming and activation of conductive film of the surface conduction electron emitter display

    Institute of Scientific and Technical Information of China (English)

    LEI Xin; XU Wei-jun; LIU Chun-liang; LIANG Zhi-hu

    2007-01-01

    The forming and activation of the conductive films are studied experimentally. The power supply,a peak-to-peak 30 V triangle profile voltage,is applied to three kinds of conductive films that contain 0.25%,0.5%,and 1% of palladium respectively. In the experiments we contrasted the values of related parameter in different conditions,observed the lumi nous spots on the anode panel,dealt with and analyzed the related data,and compared the positions and the amount of the luminous spots. We have gotten the conclusion that there is a threshold value Uth. The emission current Ie will increase rapidly when the device voltage Uf is greater than Uth. And the emission current Ie could be controlled by the device voltage Uf.The positions of the luminous spots on the anode panel are related with the device voltage Uf.

  20. Electron beam treatment of non-conducting materials by a fore-pump-pressure plasma-cathode electron beam source

    Energy Technology Data Exchange (ETDEWEB)

    Burdovitsin, V A; Klimov, A S; Medovnik, A V; Oks, E M, E-mail: burdov@fet.tusur.r [Tomsk State University of Control Systems and Radioelectronics, 634050, 40 Lenin Ave., Tomsk (Russian Federation)

    2010-10-15

    In the irradiation of an insulated target by an electron beam produced by a plasma-cathode electron beam source operating in the fore-vacuum pressure range (5-15 Pa), the target potential is much lower than the electron beam energy, offering the possibility of direct electron treatment of insulating materials. It is found that in the electron beam irradiation of a non-conducting target in a moderately high pressure range, the electron charge on the target surface is neutralized mainly by ions from a volume discharge established between the negatively charged target surface and the grounded walls of the vacuum chamber. This allows the possibility of direct electron beam treatment (heating, melting, welding) of ceramics and other non-conducting and semiconductor materials.

  1. 不同土壤转换函数预测砂土非饱和导水率的对比分析%Estimating unsaturated hydraulic conductivity of sandy soils using different pedotransfer functions

    Institute of Scientific and Technical Information of China (English)

    廖凯华; 徐绍辉; 吴吉春; 朱青

    2013-01-01

    以现有的4种土壤转换函数(Pedotransfer Functions,PTFs)(包括ROSETTA、RAWLS、CAMPBELL和VAUCLIN)为例,将其用于土壤水力性质数据库UNSODA中56个典型砂土样本的非饱和导水率预测,对4种PTFs的预测结果进行了误差分析,探讨了饱和导水率对非饱和导水率预测的影响.结果表明,当同种PTFs预测的饱和导水率作为输入时,在4种PTFs中VAUCLIN的预测精度最高,其次为ROSETTA和RAWLS,CAMPBELL的误差最大;当实测饱和导水率作为输入时,RAWLS、CAMPBELL和ROSETTA的预测精度有了不同程度提高,但VAUCLIN的预测误差反而有所增大;饱和导水率对非饱和导水率预测的影响较大,实测饱和导水率作为输入时CAMPBELL预测的非饱和导水率与实测值最为接近.%This study tested the ability of four published pedotransfer functions (PTFs) (including ROSETTA,RAWLS,CAMPBELL and VAUCLIN) to predict unsaturated hydraulic conductivity for 56 sandy soil samples from the UNSODA database.Different PTFs for the estimation of saturated hydraulic conductivity were also evaluated in this study.Results showed that among the four PTFs,VAUCLIN produced the best performance,followed by ROSETTA and RAWLS,and CAMPBELL gave the worst performance when saturated hydraulic conductivity predicted by the identical PTFs as input.The performance of RAWLS,CAMPBELL and ROSETTA has been improved to different extent when measured saturated hydraulic conductivity as input.However,VAUCLIN did not produce the best performance when measured saturated hydraulic conductivity as input.The influence of saturated hydraulic conductivity on the predictive accuracy of unsaturated hydraulic conductivity was significant.Overall,CAMPBELL gave the best performance when the measured saturated hydraulic conductivity was used in the functions for estimation of unsaturated hydraulic conductivity.

  2. Hydraulic conductivity obtained by instantaneous profile method using retention curve and neutron probes and Genuchten model; Condutividade hidraulica obtida pelo metodo do perfil instantaneo utilizando curva de retencao e sonda de neutrons e pelo modelo de Genuchten

    Energy Technology Data Exchange (ETDEWEB)

    Berretta, Ana Lucia Olmedo

    1999-07-01

    The hydraulic conductivity is one of the most important parameters to understand the movement of water in the unsaturated zone. Reliable estimations are difficult to obtain, once the hydraulic conductivity is highly variable. This study was carried out at 'Escola Superior de Agricultura Luiz de Queiroz', Universidade de Sao Paulo, in a Kandiudalfic Eutrudox soil. The hydraulic conductivity was determined by a direct and an indirect method. The instantaneous profile method was described and the hydraulic conductivity as a function of soil water content was determined by solving the Richards equation. Tensiometers were used to estimate the total soil water potential, and the neutron probe and the soil retention curve were used to estimate soil water content in the direct method. The neutron probe showed to be not adequately sensible to the changes of soil water content in this soil. Despite of the soil retention curve provides best correlation values to soil water content as a function of water redistribution time, the soil water content in this soil did not vary too much till the depth of 50 cm, reflecting the influence of the presence of a Bt horizon. The soil retention curve was well fitted by the van Genuchten model used as an indirect method. The values of the van Genuchten and the experimental relative hydraulic conductivity obtained by the instantaneous profile method provided a good correlation. However, the values estimated by the model were always lower than that ones obtained experimentally. (author)

  3. Vertical hydraulic conductivity of a clayey-silt aquitard: accelerated fluid flow in a centrifuge permeameter compared with in situ conditions

    Directory of Open Access Journals (Sweden)

    W. A. Timms

    2014-03-01

    Full Text Available Evaluating the possibility of leakage through low permeability geological strata is critically important for sustainable water supplies, extraction of fuels from strata such as coal beds, and confinement of waste within the earth. Characterizing low or negligible flow rates and transport of solutes can require impractically long periods of field or laboratory testing, but is necessary for evaluations over regional areas and over multi-decadal timescales. The current work reports a custom designed centrifuge permeameter (CP system, which can provide relatively rapid and reliable hydraulic conductivity (K measurement compared to column permeameter tests at standard gravity (1g. Linear fluid velocity through a low K porous sample is linearly related to g-level during a CP flight unless consolidation or geochemical reactions occur. The CP module is designed to fit within a standard 2 m diameter, geotechnical centrifuge with a capacity for sample dimensions of 30 to 100 mm diameter and 30 to 200 mm in length. At maximum RPM the resultant centrifugal force is equivalent to 550g at base of sample or a total stress of ~2 MPa. K is calculated by measuring influent and effluent volumes. A custom designed mounting system allows minimal disturbance of drill core samples and a centrifugal force that represents realistic in situ stress conditions is applied. Formation fluids were used as influent to limit any shrink-swell phenomena which may alter the resultant K value. Vertical hydraulic conductivity (Kv results from CP testing of core from the sites in the same clayey silt formation varied (10−7 to 10−9 m s−1, n = 14 but higher than 1g column permeameter tests of adjacent core using deionized water (10−9 to 10−11 m s−1, n = 7. Results at one site were similar to in situ Kv values (3 × 10−9 m s−1 from pore pressure responses within a 30 m clayey sequence in a homogenous area of the formation. Kv sensitivity to sample heterogeneity was

  4. Transparent conducting oxide top contacts for organic electronics

    KAUST Repository

    Franklin, Joseph B.

    2014-01-01

    A versatile method for the deposition of transparent conducting oxide (TCO) layers directly onto conjugated polymer thin film substrates is presented. Using pulsed laser deposition (PLD) we identify a narrow window of growth conditions that permit the deposition of highly transparent, low sheet resistance aluminium-doped zinc oxide (AZO) without degradation of the polymer film. Deposition on conjugated polymers mandates the use of low growth temperatures (<200°C), here we deposit AZO onto poly-3-hexylthiophene (P3HT) thin films at 150°C, and investigate the microstructural and electrical properties of the AZO as the oxygen pressure in the PLD chamber is varied (5-75 mTorr). The low oxygen pressure conditions previously optimized for AZO deposition on rigid substrates are shown to be unsuitable, resulting in catastrophic damage of the polymer films. By increasing the oxygen pressure, thus reducing the energy of the ablated species, we identify conditions that allow direct deposition of continuous, transparent AZO films without P3HT degradation. We find that uptake of oxygen into the AZO films reduces the intrinsic charge carriers and AZO films with a measured sheet resistance of approximately 500 Ω □-1 can be prepared. To significantly reduce this value we identify a novel process in which AZO is deposited over a range of oxygen pressures-enabling the deposition of highly transparent AZO with sheet resistances below 50 Ω □-1 directly onto P3HT. We propose these low resistivity films are widely applicable as transparent top-contacts in a range of optoelectronic devices and highlight this by demonstrating the operation of a semi-transparent photovoltaic device. © 2014 The Royal Society of Chemistry. 2014.

  5. Rating the characteristics of a conduction magnetohydrodynamic channel with partitions on the basis of a one dimensional hydraulic model

    Energy Technology Data Exchange (ETDEWEB)

    Bandere, Z.I.; Lavrentyev, I.V.; Shishko, A.Ya.

    1984-01-01

    A rating is conducted of the local and integral characteristics of a conduction magnetohydrodynamic (MGD) channel with partitions which operates in a pump mode. The case when both the hydrodynamic characteristics of the stream and the induced magnetic fields have a substantial effect on the operation of the channel is examined. It is shown that although flow is realized in the channel with a quite nonuniform speed profile, this has an insignificant effect on the integral characteristics of the channel; the pressure developed by the pump and the efficiency (KPD) of the channel is somewhat greater than with a uniform operational medium stream. The results are of interest for studies of liquid metal magnetohydrodynamic generators.

  6. Quantifying canal leakage rates using a mass-balance approach and heat-based hydraulic conductivity estimates in selected irrigation canals, western Nebraska, 2007 through 2009

    Science.gov (United States)

    Hobza, Christopher M.; Andersen, Michael J.

    2010-01-01

    The water supply in areas of the North Platte River Basin in the Nebraska Panhandle has been designated as fully appropriated or overappropriated by the Nebraska Department of Natural Resources (NDNR). Enacted legislation (Legislative Bill 962) requires the North Platte Natural Resources District (NPNRD) and the NDNR to develop an Integrated Management Plan (IMP) to balance groundwater and surface-water supply and demand in the NPNRD. A clear understanding of the groundwater and surface-water systems is critical for the development of a successful IMP. The primary source of groundwater recharge in parts of the NPNRD is from irrigation canal leakage. Because canal leakage constitutes a large part of the hydrologic budget, spatially distributing canal leakage to the groundwater system is important to any management strategy. Surface geophysical data collected along selected reaches of irrigation canals has allowed for the spatial distribution of leakage on a relative basis; however, the actual magnitude of leakage remains poorly defined. To address this need, the U.S. Geological Survey, in cooperation with the NPNRD, established streamflow-gaging stations at upstream and downstream ends from two selected canal reaches to allow a mass-balance approach to be used to calculate daily leakage rates. Water-level and sediment temperature data were collected and simulated at three temperature monitoring sites to allow the use of heat as a tracer to estimate the hydraulic conductivity of canal bed sediment. Canal-leakage rates were estimated by applying Darcy's Law to modeled vertical hydraulic conductivity and either the estimated or measured hydraulic gradient. This approach will improve the understanding of the spatial and temporal variability of canal leakage in varying geologic settings identified in capacitively coupled resistivity surveys. The high-leakage potential study reach of the Tri-State Canal had two streamflow-gaging stations and two temperature monitoring

  7. Localized conductive patterning via focused electron beam reduction of graphene oxide

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Songkil; Henry, Mathias [George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States); Kulkarni, Dhaval D.; Zackowski, Paul; Jang, Seung Soon; Tsukruk, Vladimir V. [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States); Fedorov, Andrei G., E-mail: agf@gatech.edu [George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States); Parker H. Petit Institute for Bioengineering and Bioscience, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States)

    2015-03-30

    We report on a method for “direct-write” conductive patterning via reduction of graphene oxide (GO) sheets using focused electron beam induced deposition (FEBID) of carbon. FEBID treatment of the intrinsically dielectric graphene oxide between two metal terminals opens up the conduction channel, thus enabling a unique capability for nanoscale conductive domain patterning in GO. An increase in FEBID electron dose results in a significant increase of the domain electrical conductivity with improving linearity of drain-source current vs. voltage dependence, indicative of a change of graphene oxide electronic properties from insulating to semiconducting. Density functional theory calculations suggest a possible mechanism underlying this experimentally observed phenomenon, as localized reduction of graphene oxide layers via interactions with highly reactive intermediates of electron-beam-assisted dissociation of surface-adsorbed hydrocarbon molecules. These findings establish an unusual route for using FEBID as nanoscale lithography and patterning technique for engineering carbon-based nanomaterials and devices with locally tailored electronic properties.

  8. Sensory properties of oxide films with high concentrations of conduction electrons

    Science.gov (United States)

    Kozhushner, M. A.; Bodneva, V. L.; Belysheva, T. V.; Gerasimov, G. N.; Gromov, V. F.; Ikim, M. I.; Paltiel, Y.; Spiridonova, E. Yu.; Trakhtenberg, L. I.

    2017-03-01

    The dependence of a sensor's response to hydrogen on the temperature and hydrogen pressure in an indium oxide nanostructured film is measured. A theory of sensor's response to reducing gases in nanostructured semiconducting oxides with high concentrations of electrons in the conduction band is developed (using the example of In2O3). It is shown that the capture of conduction electrons by adsorbed oxygen redistributes the electrons in nanoparticles and reduces the surface electron density and the conductivity of a system; the conductivity is proportional to the electron density in nanoparticle contacts, i.e., to the surface electron density. It is found that atomic oxygen ions react with reducing gases (H2, CO) during adsorption of the latter: electrons are released and enter the volumes of nanoparticles; the conductivity of the system grows, creating the sensory effect. Using a model developed earlier to describe the distribution of conduction electrons in a semiconductor nanoparticle, a kinetic scheme corresponding to the above scenario is built and corresponding equations are solved. As a result, a theoretical dependence of a sensor's sensitivity to temperature is found that describes the experimental data well.

  9. Determination of hydraulic conductivity in three dimensions and its relation to dispersivity: Chapter D in Ground-water contamination by crude oil at the Bemidji, Minnesota, research site; US Geological Survey Toxic Waste--ground-water contamination study

    Science.gov (United States)

    1984-01-01

    Recent investigations suggest that dispersion in aquifers is scale dependent and a function of the heterogeneity of aquifer materials. Theoretical stochastic studies indicate that determining hydraulic-conductivity variability in three dimensions is important in analyzing the dispersion process. Even though field methods are available to approximate hydraulic conductivity in three dimensions, the methods are not generally used because of high cost of field equipment and because measurement and analysis techniques are cumbersome and time consuming. The hypothesis of this study is that field-determined values of dispersivity are scale dependent and that they may be described as a function of hydraulic conductivity in three dimensions. The objectives of the study at the Bemidji research site are to (1) determine hydraulic conductivity of the porous media in three dimensions, (2) determine field values of dispersivity and its scale dependence on hydraulic conductivity, and (3) develop and apply a computerized data-collection, storage, and analysis system for field use in comprehensive determination of hydraulic conductivity and dispersivity. Plans for this investigation involve a variety of methods of analysis. Hydraulic conductivity will be determined separately in the horizontal and vertical planes of the hydraulic-conductivity ellipsoid. Field values of dispersivity will be determined by single-well and doublet-well injection or withdrawal tests with tracers. A computerized data-collection, storage, and analysis system to measure pressure, flow rate, tracer concentrations, and temperature will be designed for field testing. Real-time computer programs will be used to analyze field data. The initial methods of analysis will be utilized to meet the objectives of the study. Preliminary field data indicate the aquifer underlying the Bemidji site is vertically heterogeneous, cross-bedded outwash. Preliminary analysis of the flow field around a hypothetical doublet

  10. Theoretical aspects for estimating anisotropic saturated hydraulic conductivity from in-well or direct-push probe injection tests in uniform media

    Science.gov (United States)

    Klammler, Harald; Layton, Leif; Nemer, Bassel; Hatfield, Kirk; Mohseni, Ana

    2017-06-01

    Hydraulic conductivity and its anisotropy are fundamental aquifer properties for groundwater flow and transport modeling. Current in-well or direct-push field measurement techniques allow for relatively quick determination of general conductivity profiles with depth. However, capabilities for identifying local scale conductivities in the horizontal and vertical directions are very limited. Here, we develop the theoretical basis for estimating horizontal and vertical conductivities from different types of steady-state single-well/probe injection tests under saturated conditions and in the absence of a well skin. We explore existing solutions and a recent semi-analytical solution approach to the flow problem under the assumption that the aquifer is locally homogeneous. The methods are based on the collection of an additional piece of information in the form of a second injection (or recirculation) test at a same location, or in the form of an additional head or flow observation along the well/probe. Results are represented in dimensionless charts for partial validation against approximate solutions and for practical application to test interpretation. The charts further allow for optimization of a test configuration to maximize sensitivity to anisotropy ratio. The two methods most sensitive to anisotropy are found to be (1) subsequent injection from a lateral screen and from the bottom of an otherwise cased borehole, and (2) single injection from a lateral screen with an additional head observation along the casing. Results may also be relevant for attributing consistent divergences in conductivity measurements from different testing methods applied at a same site or location to the potential effects of anisotropy. Some practical aspects are discussed and references are made to existing methods, which appear easily compatible with the proposed procedures.

  11. Electron transport through supported biomembranes at the nanoscale by conductive atomic force microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Casuso, I [Department Electronica, Universitat de Barcelona and Laboratori de Nanobioenginyeria-IBEC, Parc CientIfic de Barcelona, Barcelona (Spain); Fumagalli, L [Department Electronica, Universitat de Barcelona and Laboratori de Nanobioenginyeria-IBEC, Parc CientIfic de Barcelona, Barcelona (Spain); Samitier, J [Department Electronica, Universitat de Barcelona and Laboratori de Nanobioenginyeria-IBEC, Parc CientIfic de Barcelona, Barcelona (Spain); Padros, E [Unitat de BiofIsica, Departamento de BioquImica i de Biologia Molecular, Facultat de Medicina i Centre d' Estudis en BiofIsica, Universitat Autonoma de Barcelona, Barcelona (Spain); Reggiani, L [CNR-INFM National Nanotechnology Laboratory, Dipartimento di Ingegneria dell' Innovazione, Universita di Lecce, Lecce (Italy); Akimov, V [CNR-INFM National Nanotechnology Laboratory, Dipartimento di Ingegneria dell' Innovazione, Universita di Lecce, Lecce (Italy); Gomila, G [Department Electronica, Universitat de Barcelona and Laboratori de Nanobioenginyeria-IBEC, Parc CientIfic de Barcelona, Barcelona (Spain)

    2007-11-21

    We present a reliable methodology to perform electron transport measurements at the nanoscale on supported biomembranes by conductive atomic force microscopy (C-AFM). It allows measurement of both (a) non-destructive conductive maps and (b) force controlled current-voltage characteristics in wide voltage bias range in a reproducible way. Tests experiments were performed on purple membrane monolayers, a two-dimensional (2D) crystal lattice of the transmembrane protein bacteriorhodopsin. Non-destructive conductive images show uniform conductivity of the membrane with isolated nanometric conduction defects. Current-voltage characteristics under different compression conditions show non-resonant tunneling electron transport properties, with two different conduction regimes as a function of the applied bias, in excellent agreement with theoretical predictions. This methodology opens the possibility for a detailed study of electron transport properties of supported biological membranes, and of soft materials in general.

  12. Significant Electronic Thermal Transport in the Conducting Polymer Poly(3,4‐ethylenedioxythiophene)

    DEFF Research Database (Denmark)

    Weathers, Annie; Khan, Zia Ullah; Brooke, Robert;

    2015-01-01

    Suspended microdevices are employed to measure the in-plane electrical conductivity, thermal conductivity, and Seebeck coefficient of suspended poly(3,4-ethylenedioxythiophene) (PEDOT) thin films. The measured thermal conductivity is higher than previously reported for PEDOT and generally increas...... with the electrical conductivity. The increase exceeds that predicted by the Wiedemann–Franz law for metals and can be explained by significant electronic thermal transport in PEDOT....

  13. Mathematical and geological approaches to minimizing the data requirements for statistical analysis of hydraulic conductivity. Technical completion report

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, F.M.; Wilson, J.L.; Gutjahr, A.L.; Love, D.W.; Davis, J.M.; Lohmann, R.C.; Colarullo, S.J.; Gotkowitz, M.B.

    1992-12-01

    Field scale heterogeneity has been recognized as a dominant control on solute dispersion in groundwater. Numerous random field models exist for quantifying heterogeneity and its influence on solute transport. Minimizing data requirements in model selection and subsequent parameterization will be necessary for efficient application of quantitative models in contaminated subsurface environments. In this study, a detailed quantitative sedimentological study is performed to address the issue of incorporating geologic information into the geostatistical characterization process. A field air-minipermeameter is developed for rapid in-situ measurements. The field study conducted on an outcrop of fluvial/interfluvial deposits of the Pliocene- Pleistocene Sierra Ladrones Formation in the Albuquerque Basin of central New Mexico. Architectural element analysis is adopted for mapping and analysis of depositional environment. Geostatistical analysis is performed at two scales. At the architectural element scale, geostatistical analysis of assigned mean log-permeabilities of a 0.16 km{sup 2} peninsular region indicates that the directions of maximum and minimum correlation correspond to the directions of the large-scale depositional processes. At the facies scale, permeability is found to be adequately represented as a log-normal process. Log-permeability within individual lithofacies appears uncorrelated. The overall correlation structure at the facies scale is found to be a function of the mean log-permeability and spatial distribution of the individual lithofacies. Based on field observations of abrupt spatial changes in lithology and hydrologic properties, an algorithm for simulating multi-dimensional discrete Markov random fields. Finally, a conceptual model is constructed relating the information inferred from dimensional environment analysis to the various random fields of heterogeneity.

  14. Inkjet-printed conductive features for rapid integration of electronic circuits in centrifugal microfluidics

    CSIR Research Space (South Africa)

    Kruger, J

    2015-05-01

    Full Text Available This work investigates the properties of conductive circuits inkjet-printed onto the polycarbonate discs used in CD-based centrifugal microfluidics, contributing towards rapidly prototyped electronic systems in smart ubiquitous biosensors, which...

  15. Room temperature Compton profiles of conduction electrons in -Ga metal

    Indian Academy of Sciences (India)

    B P Panda; N C Mohapatra

    2003-12-01

    Room temperature Compton profiles of momentum distribution of conduction electrons in -Ga metal are calculated in band model. For this purpose, the conduction electron wave functions are determined in a temperature-dependent non-local model potential. The profiles calculated along the crystallographic directions, (100), (010), and (001) are found to be nearly isotropic. This conclusion is in reasonable agreement with experimental observations.

  16. Enhancing the Electronic Conductivity of Vanadium-tellurite Glasses by Tuning the Redox State

    DEFF Research Database (Denmark)

    Kjeldsen, Jonas; Yue, Yuanzheng

    . In this work we vary the redox state of a given vanadium tellurite system by performing post heat-treatment in controlled atmosphere. This process is in theory not limited only to varying electronic conductivity, but also varying the glass structure, and hence, changing properties of the glasses, e.g, thermal...... and mechanical properties. Finally we give insight into the relation between the redox state and electronic conductivity....

  17. Optical and electronic properties of conductive ternary nitrides with rare- or alkaline-earth elements

    Science.gov (United States)

    Kassavetis, S.; Hodroj, A.; Metaxa, C.; Logothetidis, S.; Pierson, J. F.; Patsalas, P.

    2016-12-01

    Conductive nitrides, such as TiN, are key engineering materials for electronics, photonics, and plasmonics; one of the essential issues for such applications is the ability of tuning the conduction electron density, the resistivity, and the electron scattering. While enhancing the conduction electron density and blueshifting the intraband absorption towards the UV were easily achieved previously, reducing the conduction electron density and redshifting the intraband absorption into the infrared are still an open issue. The latter is achieved in this work by alloying TiN by rare earth (RE = Sc, Y, La) or alkaline earth (AE = Mg, Ca) atoms in Ti substitutional positions. The produced TixRE1-xN and TixAE1-xN thin film samples were grown by a hybrid arc evaporation/sputtering process, and most of them are stable in the B1 cubic structure. Their optical properties were studied in an extensive spectral range by spectroscopic ellipsometry. The ellipsometric spectra were analyzed and quantified by the Drude-Lorentz model, which provided the conduction electron density, the electron mean free path, and the resistivity. The observed interband transitions are firmly assigned, and the optical and electrical properties of TixRE1-xN and TixAE1-xN are quantitatively correlated with their composition and crystal structure.

  18. 12 CFR 7.5008 - Location of a national bank conducting electronic activities.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Location of a national bank conducting electronic activities. 7.5008 Section 7.5008 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE... because the bank's products or services are accessed through electronic means by customers located in the...

  19. Nanoscale Soldering of Positioned Carbon Nanotubes using Highly Conductive Electron Beam Induced Gold Deposition

    DEFF Research Database (Denmark)

    Madsen, Dorte Nørgaard; Mølhave, Kristian; Mateiu, Ramona Valentina

    2003-01-01

    We have developed an in-situ method for controlled positioning of carbon nanotubes followed by highly conductive contacting of the nanotubes, using electron beam assisted deposition of gold. The positioning and soldering process takes place inside an Environmental Scanning Electron Microscope (E...

  20. Signature of f -electron conductance in α -Ce single-atom contacts

    Science.gov (United States)

    Kuntz, Sebastian; Berg, Oliver; Sürgers, Christoph; Löhneysen, Hilbert v.

    2017-08-01

    Cerium is a fascinating element exhibiting, with its different phases, long-range magnetic order and superconductivity in bulk form. The coupling of the 4 f electron to s d conduction electrons and to the lattice is responsible for unique structural and electronic properties like the isostructural first-order solid-solid transition from the cubic γ phase to the cubic α phase, which is accompanied by a huge volume collapse of 14%. We report experiments aiming at disentangling the 4 f contribution to the electric conductance of the different phases. On single-atom Ce contacts we observe a strongly enhanced conductance G . By controlling the content of α -Ce employing different rates of cooling, we find a strong correlation between the fraction of α -Ce and the magnitude of G at the last conductance plateau before the contact breaks. We attribute the enhanced conductance of α -Ce to the additional contribution of the 4 f level.

  1. Conductivity magnetooscillations in 2D electron-impurity system under microwave irradiation: role of magnetoplasmons

    OpenAIRE

    Takhtamirov, E. E.; V. A. Volkov

    2005-01-01

    It is developed a many-electron approach to explain the recently observed conductivity magnetooscillations in very high mobility 2D electron systems under microwave irradiation. For the first time a theory takes into account the microwave-induced renormalization of the screened impurity potential. As a result this potential has singular, dynamic and non-linear in electric field nature. That changes the picture of scattering of electrons at impurities in a ``clean'' 2D system essentially: for ...

  2. Mineralogical composition and phase-to-phase relationships in natural hydraulic lime and/or natural cement - raw materials and burnt products revealed by scanning electron microscopy

    Science.gov (United States)

    Kozlovcev, Petr; Přikryl, Richard; Racek, Martin; Přikrylová, Jiřina

    2016-04-01

    In contrast to modern process of production of cement clinker, traditional burning of natural hydraulic lime below sintering temperature relied on the formation of new phases from ion migration between neighbouring mineral grains composing raw material. The importance of the mineralogical composition and spatial distribution of rock-forming minerals in impure limestones used as a raw material for natural hydraulic lime presents not well explored issue in the scientific literature. To fill this gap, the recent study focuses in detailed analysis of experimentally burnt impure limestones (mostly from Barrandian area, Bohemian Massif). The phase changes were documented by optical microscopy, X-ray diffraction, and scanning electron microscopy with an energy dispersive spectrometer (SEM-EDS) coupled with x-ray elemental mapping. The latest allowed for visualization of distribution of elements within raw materials and burnt products. SEM/EDS study brought valuable data on the presence of transitional and/or minor phases, which were poorly detectable by other methods.

  3. Conjugate polymers and electronic conductive polymers; Polymeres conjugues et polymeres conducteurs electroniques

    Energy Technology Data Exchange (ETDEWEB)

    Attias, A.J. [Universite Pierre et Marie Curie, Lab. de Chimie Macromoleculaire, UMR 7610 - CNRS, 75 - Paris (France)

    2002-05-01

    In some certain conditions a plastic material can become conductive (synthetic metal). To become conductive, a polymer must be conjugate (alternance of simple and multiple bonds) and doped (electron removal or addition). This article presents the recent advances and trends of the research on conductive polymers. The role of {pi} electrons in the conjugate systems is recalled in a first part. The description of energy states of conjugate polymers in terms of bands structure allow to consider them as organic semiconductors. Thus, it is possible to generate charged species by doping, charge injection or photo-excitation. These charge carriers, the conduction mechanisms and the related applications are presented. The chemistry and synthesis of these polymers are presented in a second part: 1 - evolution of research; 2 - physics of conductive polymers (role of {pi} electrons in conjugate polymers, {pi}-electrons conjugate compounds, influence of conjugation length and notion of bands structure, charges-doping generation, conductive polymers, chemical doping and electrical conduction, charge injection at the conjugate semiconductor metal-polymer interface: electro-luminescent polymers, charge creation by photo-excitation: polymers for photovoltaic cells); 3 - chemistry of conductive polymers (role of synthesis, monomers choice, other trends). (J.S.)

  4. Absolute negative conductivity in two-dimensional electron systems under microwave radiation

    OpenAIRE

    Ryzhii, Victor

    2004-01-01

    We overview mechanisms of absolute negative conductivity in two-dimensional electron systems in a magnetic field irradiated with microwaves and provide plausible explanations of the features observed in recent experiments related to the so-called zero-resistance (zero-conductance) states.

  5. Electron and Ion Conductivity Calculations using the Model of Lee and More

    Energy Technology Data Exchange (ETDEWEB)

    Hayes, John C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-09-30

    The following notes describe the ARES implementation of the inverse of the electron conduction coefficient, using the model of Lee and More, Physics of Fluids 27, page 1273, 1984. An addendum describing the modifications for analogous ion conduction coeffiecient appears at the bottom.

  6. Hydraulic structures

    CERN Document Server

    Chen, Sheng-Hong

    2015-01-01

    This book discusses in detail the planning, design, construction and management of hydraulic structures, covering dams, spillways, tunnels, cut slopes, sluices, water intake and measuring works, ship locks and lifts, as well as fish ways. Particular attention is paid to considerations concerning the environment, hydrology, geology and materials etc. in the planning and design of hydraulic projects. It also considers the type selection, profile configuration, stress/stability calibration and engineering countermeasures, flood releasing arrangements and scouring protection, operation and maintenance etc. for a variety of specific hydraulic structures. The book is primarily intended for engineers, undergraduate and graduate students in the field of civil and hydraulic engineering who are faced with the challenges of extending our understanding of hydraulic structures ranging from traditional to groundbreaking, as well as designing, constructing and managing safe, durable hydraulic structures that are economical ...

  7. Electrical conductivity and electron-spin resonance in oxidatively stabilized polyacrylonitrile subjected to elevated temperature

    Science.gov (United States)

    Lerner, N. R.

    1981-01-01

    Electrical conductivity and electron spin resonance measurements are presented for oxidatively stabilized polyacrylonitrile (PAN) fibers subjected to heat treatment at temperatures ranging from 700 to 950 K. Conductivity measurements made at temperatures between 77 and 523 K reveal that PAN fibers heat treated in vacuum behave as semiconductors, with a room-temperature conductivity dominated by the contributions of impurity states, with an activation energy of 88 kcal/mole. A decrease in conductivity is observed upon air which is attributed to a decrease in the electron-phonon scattering time. ESR spectra indicate that conducting pathways having metallic properties are formed at temperatures as low as 715 K, although the contribution of these pathways to the room-temperature conductivity is extremely small next to the contribution of localized spin centers.

  8. Suppression of Electron Thermal Conduction in the High β Intracluster Medium of Galaxy Clusters

    Science.gov (United States)

    Roberg-Clark, G. T.; Drake, J. F.; Reynolds, C. S.; Swisdak, M.

    2016-10-01

    Understanding the thermodynamic state of the hot intracluster medium (ICM) in a galaxy cluster requires knowledge of the plasma transport processes, especially thermal conduction. The basic physics of thermal conduction in plasmas with ICM-like conditions has yet to be elucidated, however. We use particle-in-cell simulations and analytic models to explore the dynamics of an ICM-like plasma (with small gyroradius, large mean free path, and strongly sub-dominant magnetic pressure) driven by the diffusive heat flux associated with thermal conduction. Linear theory reveals that whistler waves are driven unstable by electron heat flux, even when the heat flux is weak. The resonant interaction of electrons with these waves then plays a critical role in scattering electrons and suppressing the heat flux. In a 1D model where only whistler modes that are parallel to the magnetic field are captured, the only resonant electrons are moving in the opposite direction to the heat flux, and the electron heat flux suppression is small. In 2D or more, oblique whistler modes also resonate with electrons moving in the direction of the heat flux. The overlap of resonances leads to effective symmetrization of the electron distribution function and a strong suppression of heat flux. The results suggest that thermal conduction in the ICM might be strongly suppressed, possibly to negligible levels.

  9. HYDRAULIC SERVO

    Science.gov (United States)

    Wiegand, D.E.

    1962-05-01

    A hydraulic servo is designed in which a small pressure difference produced at two orifices by an electrically operated flapper arm in a constantly flowing hydraulic loop is hydraulically amplified by two constant flow pumps, two additional orifices, and three unconnected ball pistons. Two of the pistons are of one size and operate against the additional orifices, and the third piston is of a different size and operates between and against the first two pistons. (AEC)

  10. Resonant enhancement in nanostructured thermoelectric performance via electronic thermal conductivity engineering

    Science.gov (United States)

    Patil, Urvesh; Muralidharan, Bhaskaran

    2017-01-01

    The use of an asymmetric broadening in the transport distribution, a characteristic of resonant structures, is proposed as a route to engineer a decrease in electronic thermal conductivity thereby enhancing the electronic figure of merit in nanostructured thermoelectrics. Using toy models, we first demonstrate that a decrease in thermal conductivity resulting from such an asymmetric broadening may indeed lead to an electronic figure of merit well in excess of 1000 in an idealized situation and in excess of 10 in a realistic situation. We then substantiate with realistic resonant structures designed using graphene nano-ribbons by employing a tight binding framework with edge correction that match density functional theory calculations under the local density approximation. The calculated figure of merit exceeding 10 in such realistic structures further reinforces the concept and sets a promising direction to use nano-ribbon structures to engineer a favorable decrease in the electronic thermal conductivity.

  11. Conductivity of solvated electrons in hexane investigated with terahertz time-domain spectroscopy.

    Science.gov (United States)

    Knoesel, Ernst; Bonn, Mischa; Shan, Jie; Wang, Feng; Heinz, Tony F

    2004-07-01

    We present investigations of the transient photoconductivity and recombination dynamics of quasifree electrons in liquid n-hexane and cyclohexane performed using terahertz time-domain spectroscopy (THz-TDS). Quasifree electrons are generated by two-photon photoionization of the liquid using a femtosecond ultraviolet pulse, and the resulting changes in the complex conductivity are probed by a THz electromagnetic pulse at a variable delay. The detection of time-domain wave forms of the THz electric field permits the direct determination of both the real and the imaginary part of the conductivity of the electrons over a wide frequency range. The change in conductivity can be described by the Drude model, thus yielding the quasifree electron density and scattering time. The electron density is found to decay on a time scale of a few hundred picoseconds, which becomes shorter with increasing excitation density. The dynamics can be described by a model that assumes nongeminate recombination between electrons and positive ions. In addition, a strong dependence of the quasifree electron density on temperature is observed, in agreement with a two-state model in which the electron may exist in either a quasifree or a bound state.

  12. Calculation of thermal conductivity coefficients of electrons in magnetized dense matter

    CERN Document Server

    Bisnovatyi-Kogan, G S

    2016-01-01

    The solution of Boltzmann equation for plasma in magnetic field, with arbitrarily degenerate electrons and non-degenerate nuclei, is obtained by Chapman-Enskog method. Functions, generalizing Sonin polynomials are used for obtaining an approximate solution. Fully ionized plasma is considered. The tensor of the heat conductivity coefficients in non-quantized magnetic field is calculated. For non-degenerate and strongly degenerate plasma the asymptotic analytic formulas are obtained, which are compared with results of previous authors. The Lorentz approximation, with neglecting of electron-electron encounters, is asymptotically exact for strongly degenerate plasma. For non-degenerate plasma the solution at 3-function approximation for Lorentz gas deviate from the exact solution for about 2.2\\%, at zero magnetic field. We obtain the solution for the heat conductivity tensor for the case of non-degenerate electrons, in presence of a magnetic field, in three polynomial approximation with account of electron-electr...

  13. Numerical analysis of the surface-conduction electron-emitter with a new configuration

    Science.gov (United States)

    Shen, Zhihua; Wang, Xiao; Wu, Shengli; Tian, Jinshou

    2016-04-01

    A new kind of surface-conduction electron-emitter (SCE) with a triangular dielectric layer under the conductive film is proposed. The influences of the vertex angle (𝜃) of the triangular dielectric layer and the anode voltage (Ua) on the electron emission efficiency and the focusing capability have been investigated with the finite integration technique (FIT). The numerical simulation results show that SCE with a small vertex angle guarantees higher electron emission efficiency even with a low anode voltage. But the focusing capability of the electron emitter will get worse when the 𝜃 or Ua becomes too small. Take both the electron emission efficiency and focusing capability into consideration, the structure with a vertex angle (𝜃) between 60∘-100∘ and the anode voltage of 1500V is suggested.

  14. Quantum thermal conductance of electrons in a one-dimensional wire.

    Science.gov (United States)

    Chiatti, O; Nicholls, J T; Proskuryakov, Y Y; Lumpkin, N; Farrer, I; Ritchie, D A

    2006-08-04

    We use an electron thermometer to measure the temperature rise of approximately 2 x 10(5) electrons in a two-dimensional box, due to heat flow into the box through a ballistic one-dimensional (1D) constriction. Using a simple model we deduce the thermal conductance kappa(Vg) of the 1D constriction, which we compare to its electrical conductance characteristics; for the first four 1D subbands the heat carried by the electrons passing through the wire is proportional to its electrical conductance G(Vg). In the vicinity of the 0.7 structure this proportionality breaks down, and a plateau at the quantum of thermal conductance pi(2)k(2/B)T/3h is observed.

  15. Electron conduction and trapping in DNA; An electron spin resonance study

    Energy Technology Data Exchange (ETDEWEB)

    Cullis, P.M.; McClymont, J.D.; Symons, M.C.R. (Cambridge Univ. (UK). Dept. of Clinical Oncology and Radiotherapeutics)

    1990-02-01

    Exposure of intercalated DNA to {gamma}-rays at 77 K gives two radical anions, identified as thymine (T{sup .-}) and intercalator (Int{sup .-}) radical anions. Growth of the Int{sup .-} signal follows an exponential law with 50% scavenging of T{sup .-} at ca. 1 : 110 (Int{sup .-} to base pairs). Thus on average, electrons traverse ca. 200 bases before becoming trapped. (author).

  16. Directly patternable, highly conducting polymers for broad applications in organic electronics.

    Science.gov (United States)

    Yoo, Joung Eun; Lee, Kwang Seok; Garcia, Andres; Tarver, Jacob; Gomez, Enrique D; Baldwin, Kimberly; Sun, Yangming; Meng, Hong; Nguyen, Thuc-Quyen; Loo, Yueh-Lin

    2010-03-30

    Postdeposition solvent annealing of water-dispersible conducting polymers induces dramatic structural rearrangement and improves electrical conductivities by more than two orders of magnitude. We attain electrical conductivities in excess of 50 S/cm when polyaniline films are exposed to dichloroacetic acid. Subjecting commercially available poly(ethylene dioxythiophene) to the same treatment yields a conductivity as high as 250 S/cm. This process has enabled the wide incorporation of conducting polymers in organic electronics; conducting polymers that are not typically processable can now be deposited from solution and their conductivities subsequently enhanced to practical levels via a simple and straightforward solvent annealing process. The treated conducting polymers are thus promising alternatives for metals as source and drain electrodes in organic thin-film transistors as well as for transparent metal oxide conductors as anodes in organic solar cells and light-emitting diodes.

  17. Self-similar variables and the problem of nonlocal electron heat conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Krasheninnikov, S.I.; Bakunin, O.G. [Massachusetts Inst. of Tech., Cambridge, MA (United States). Plasma Fusion Center]|[Kurchatov Inst. of Atomic Energy, Moscow (Russian Federation)

    1993-10-01

    Self-similar solutions of the collisional electron kinetic equation are obtained for the plasmas with one (1D) and three (3D) dimensional plasma parameter inhomogeneities and arbitrary Z{sub eff}. For the plasma parameter profiles characterized by the ratio of the mean free path of thermal electrons with respect to electron-electron collisions, {gamma}{sub T}, to the scale length of electron temperature variation, L, one obtains a criterion for determining the effect that tail particles with motion of the non-diffusive type have on the electron heat conductivity. For these conditions it is shown that the use of a {open_quotes}symmetrized{close_quotes} kinetic equation for the investigation of the strong nonlocal effect of suprathermal electrons on the electron heat conductivity is only possible at sufficiently high Z{sub eff} (Z{sub eff} {ge} (L/{gamma}{sub T}){sup 1/2}). In the case of 3D inhomogeneous plasma (spherical symmetry), the effect of the tail electrons on the heat transport is less pronounced since they are spread across the radius r.

  18. Towards seamlessly-integrated textile electronics: methods to coat fabrics and fibers with conducting polymers for electronic applications.

    Science.gov (United States)

    Allison, Linden; Hoxie, Steven; Andrew, Trisha L

    2017-06-29

    Traditional textile materials can be transformed into functional electronic components upon being dyed or coated with films of intrinsically conducting polymers, such as poly(aniline), poly(pyrrole) and poly(3,4-ethylenedioxythiophene). A variety of textile electronic devices are built from the conductive fibers and fabrics thu