WorldWideScience

Sample records for human feeder layer

  1. Replacement of murine fibroblasts by human fibroblasts irradiated in obtaining feeder layer for the culture of human keratinocytes

    International Nuclear Information System (INIS)

    Yoshito, Daniele; Sufi, Bianca S.; Santin, Stefany P.; Mathor, Monica B.; Altran, Silvana C.; Isaac, Cesar

    2011-01-01

    Human autologous epithelia cultivated in vitro, have been used successfully in treating damage to skin integrity. The methodology allowed the cultivation of these epithelia was described by Rheinwald and Green in 1975, this methodology consisted in seeding keratinocytes onto a feeder layer composed of lineage 3T3 murine fibroblasts, the proliferation rate is controlled through the action of ionizing radiation. However, currently there is a growing concern about the possibility of transmitting prions and murine viruses to transplanted patients. Taking into account this concern, in this present work, we replaced the feeder layer originally composed of murine fibroblasts by human fibroblasts. To obtain this new feeder layer was necessary to standardize the enough irradiation dose to inhibit the replication of human fibroblasts and the verification of effectiveness of the development of keratinocytes culture on a feeder layer thus obtained. According to the obtained results we can verify that the human fibroblasts irradiated at various tested doses (60, 70, 100, 200, 250 and 300 Gy) had their mitotic activity inactivated by irradiation, allowing the use of any of these doses to confection of the feeder layer, since these fibroblasts irradiated still showed viable until fourteen days of cultivation. In the test of colony formation efficiency was observed that keratinocytes seeded on irradiated human fibroblasts were able to develop satisfactorily, preserving their clonogenic potential. Therefore it was possible the replacement of murine fibroblasts by human fibroblasts in confection of the feeder layer, in order to eliminate this xenobiotic component of the keratinocytes culture. (author)

  2. Replacement of murine fibroblasts by human fibroblasts irradiated in obtaining feeder layer for the culture of human keratinocytes

    Energy Technology Data Exchange (ETDEWEB)

    Yoshito, Daniele; Sufi, Bianca S.; Santin, Stefany P.; Mathor, Monica B. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Altran, Silvana C.; Isaac, Cesar [Universidade Sao Paulo (USP), Sao Paulo, SP (Brazil). Fac. de Medicina. Lab. de Microcirurgia Plastica; Esteves-Pedro, Natalia M. [Universidade Sao Paulo (USP), Sao Paulo, SP (Brazil). Fac. de Ciencias Farmaceuticas. Lab. de Controle Biologico; Herson, Marisa R. [DonorTissue Bank of Victoria (Australia)

    2011-07-01

    Human autologous epithelia cultivated in vitro, have been used successfully in treating damage to skin integrity. The methodology allowed the cultivation of these epithelia was described by Rheinwald and Green in 1975, this methodology consisted in seeding keratinocytes onto a feeder layer composed of lineage 3T3 murine fibroblasts, the proliferation rate is controlled through the action of ionizing radiation. However, currently there is a growing concern about the possibility of transmitting prions and murine viruses to transplanted patients. Taking into account this concern, in this present work, we replaced the feeder layer originally composed of murine fibroblasts by human fibroblasts. To obtain this new feeder layer was necessary to standardize the enough irradiation dose to inhibit the replication of human fibroblasts and the verification of effectiveness of the development of keratinocytes culture on a feeder layer thus obtained. According to the obtained results we can verify that the human fibroblasts irradiated at various tested doses (60, 70, 100, 200, 250 and 300 Gy) had their mitotic activity inactivated by irradiation, allowing the use of any of these doses to confection of the feeder layer, since these fibroblasts irradiated still showed viable until fourteen days of cultivation. In the test of colony formation efficiency was observed that keratinocytes seeded on irradiated human fibroblasts were able to develop satisfactorily, preserving their clonogenic potential. Therefore it was possible the replacement of murine fibroblasts by human fibroblasts in confection of the feeder layer, in order to eliminate this xenobiotic component of the keratinocytes culture. (author)

  3. Utilization of human amniotic mesenchymal cells as feeder layers to sustain propagation of human embryonic stem cells in the undifferentiated state.

    Science.gov (United States)

    Zhang, Kehua; Cai, Zhe; Li, Yang; Shu, Jun; Pan, Lin; Wan, Fang; Li, Hong; Huang, Xiaojie; He, Chun; Liu, Yanqiu; Cui, Xiaohui; Xu, Yang; Gao, Yan; Wu, Liqun; Cao, Shanxia; Li, Lingsong

    2011-08-01

    Human embryonic stem (ES) cells are usually maintained in the undifferentiated state by culturing on feeder cells layers of mouse embryonic fibroblasts (MEFs). However, MEFs are not suitable to support human ES cells used for clinical purpose because of risk of zoonosis from animal cells. Therefore, human tissue-based feeder layers need to be developed for human ES cells for clinical purpose. Hereof we report that human amniotic mesenchymal cells (hAMCs) could act as feeder cells for human ES cells, because they are easily obtained and relatively exempt from ethical problem. Like MEFs, hAMCs could act as feeder cells for human ES cells to grow well on. The self-renewal rate of human ES cells cultured on hAMCs feeders was higher than that on MEFs and human amniotic epithelial cells determined by measurement of colonial diameters and growth curve as well as cell cycle analysis. Both immunofluorescence staining and immunoblotting showed that human ES cells cultured on hAMCs expressed stem cell markers such as Oct-3/4, Sox2, and NANOG. Verified by embryoid body formation in vitro and teratoma formation in vivo, we found out that after 20 passages of culture, human ES cells grown on hAMCs feeders could still retain the potency of differentiating into three germ layers. Taken together, our data suggested hAMCs may be safe feeder cells to sustain the propagation of human ES cells in undifferentiated state for future therapeutic use.

  4. Irradiated murine fibroblasts as feeder layer used in human cell culture

    International Nuclear Information System (INIS)

    Almeida, Tiago L.; Klingbeil, Fatima G.; Yoshito, Daniele; Caproni, Priscila; Mathor, Monica B.; Herson, Marisa R.

    2007-01-01

    In 1975, Rheinwald and Green published an in vitro model for keratinocyte cell cultures in which the use of murine fibroblasts, as a feeder layer was introduced. These cells are modified fibroblasts, which presence render keratinocyte cells to remain proliferative for longer periods of time. This optimization of culture outputs has allowed for several clinical applications of confluent keratinocyte cultures as skin substitutes or wound dressings in situations such as post burn extensive skin loss, loss of oral mucosa, and other skin disorders. Nevertheless, proliferation of fibroblast in co-culture with keratinocytes must be controlled by anti-proliferative measures such as irradiation; at the same time, keratinocytes require specific nutrients in the culture medium, which may interfere with the fibroblast feeder layer viability. Therefore, the thorough understanding of the impact of different issues such as culture media composition, irradiation dose and pre-plating storage conditions of irradiated fibroblast to be used as feeder layer in these co-culture systems is important. In this work, changes as far as viability and proliferative rates of irradiated fibroblasts in culture were evaluated in relation to the type of culture medium used, dose of gamma radiation exposure, storage and timing of cell plating post irradiation. Results indicate that the type of culture medium used and time-lag between irradiation, refrigeration and plating of irradiated cells do not have significant impact in culture outcomes. However, the dose of gamma radiation administered to the cells may influence the final quality of these cells if to be used as a feeder layer. (author)

  5. Evaluation of the effect of radiation levels and dose rates in irradiation of murine fibroblasts used as a feeder layer in the culture of human keratinocytes

    International Nuclear Information System (INIS)

    Yoshito, Daniele; Almeida, Tiago L.; Santin, Stefany Plumeri; Somessari, Elizabeth S.R.; Silveira, Carlos G. da; Mathor, Monica B.; Altran, Silvana C.; Isaac, Cesar

    2009-01-01

    In 1975, Rheinwald and Green published an effective methodology for obtaining and cultivating human keratinocytes. This methodology consisted of seeding keratinocytes onto a feeder layer composed of lineage 3T3 murine fibroblasts, the proliferation rate of which is then controlled through the action of ionizing radiation. The presence of the feeder layer encourages the development of keratinocyte colonies and their propagation in similar cultures, becoming possible several clinical applications as skin substitutes or wound dressings in situations such as post burn extensive skin loss and other skin disorders. However, good development of these keratinocytes depends on a high quality feeder layer among other factors. In the present work, we evaluated the relationship between radiation levels and dose rates applied to fibroblasts used in construction of feeder layers and the radiation effect on keratinocytes colonies forming efficiency. Results indicate 3T3 lineage murine fibroblasts irradiated with doses varying between 60 and 100 Gy can be used as a feeder layer immediately after irradiation or storage of the irradiated cells in suspension at 4 g C for 24 hours with similar results. The exception is when the irradiation dose rate is 2.75 Gyh -1 ; in this case, results suggested that the fibroblasts should be used immediately after irradiation. (author)

  6. Cultivation and irradiation of human fibroblasts in a medium enriched with platelet lysate for obtaining feeder layer in epidermal cell culture

    International Nuclear Information System (INIS)

    Yoshito, Daniele

    2011-01-01

    For over 30 years, the use of culture medium, enriched with bovine serum, and murines fibroblasts, with the rate of proliferation controlled by irradiation or by share anticarcinogenic drugs, has been playing successfully its role in assisting in the development of keratinocytes in culture, for clinical purposes. However, currently there is a growing concern about the possibility of transmitting prions and animals viruses to transplanted patients. Taking into account this concern, the present work aims to cultivate human fibroblasts in a medium enriched with human platelets lysate and determine the irradiation dose of these cells, for obtaining feeder layer in epidermal cell culture. For carrying out the proposed objective, platelets lysis has standardized, this lysate was used for human fibroblasts cultivation and the irradiation dose enough to inhibit its duplication was evaluated. Human keratinocytes were cultivated in these feeder layers, in culture medium enriched with the lysate. With these results we conclude that the 10% platelets lysate promoted a better adhesion and proliferation of human fibroblasts and in all dose levels tested (60 to 300 Gy), these had their mitotic activity inactivated by ionizing irradiation, being that the feeder layers obtained with doses from 70 to 150 Gy were those that provided the best development of keratinocytes in medium containing 2.5% of human platelet lysate. Therefore, it was possible to standardize both the cultivation of human fibroblasts as its inactivation for use as feeder layer in culture of keratinocytes, so as to eliminate xenobiotics components. (author)

  7. Human amniotic epithelial cell feeder layers maintain human iPS cell pluripotency via inhibited endogenous microRNA-145 and increased Sox2 expression

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Te, E-mail: liute79@yahoo.com [School of Environmental Science and Engineering, Donghua University, Shanghai 201620 (China); Shanghai Geriatric Institute of Chinese Medicine, Shanghai 200031 (China); Cheng, Weiwei [International Peace Maternity and Child Health Hospital, Shanghai Jiaotong University, Shanghai 200030 (China); Huang, Yongyi [Laboratoire PROTEE, Batiment R, Universite du Sud Toulon-Var, 83957 LA GARDE Cedex (France); Huang, Qin; Jiang, Lizhen [Institute of Biochemistry and Cell Biology, Shanghai Institute for Biological Sciences, Chinese Academy of Sciences, Shanghai 200031 (China); Guo, Lihe, E-mail: liute79@yahoo.com [Institute of Biochemistry and Cell Biology, Shanghai Institute for Biological Sciences, Chinese Academy of Sciences, Shanghai 200031 (China)

    2012-02-15

    Currently, human induced pluripotent stem (iPS) cells were generated from patient or disease-specific sources and share the same key properties as embryonic stem cells. This makes them attractive for personalized medicine, drug screens or cellular therapy. Long-term cultivation and maintenance of normal iPS cells in an undifferentiated self-renewing state are a major challenge. Our previous studies have shown that human amniotic epithelial cells (HuAECs) could provide a good source of feeder cells for mouse and human embryonic stem cells, or spermatogonial stem cells, but the mechanism for this is unknown. Here, we examined the effect of endogenous microRNA-145 regulation on Sox2 expression in human iPS cells by HuAECs feeder cells regulation, and in turn on human iPS cells pluripotency. We found that human IPS cells transfected with a microRNA-145 mutant expressed Sox2 at high levels, allowing iPS to maintain a high level of AP activity in long-term culture and form teratomas in SCID mice. Expression of stem cell markers was increased in iPS transfected with the microRNA-145 mutant, compared with iPS was transfected with microRNA-145. Besides, the expression of Drosha proteins of the microRNA-processor complex, required for the generation of precursor pre-miRNA, was significantly increased in human iPS cells cultured on MEF but not on HuAECs. Taken together, these results suggest that endogenous Sox2 expression may be regulated by microRNA-145 in human iPS cells with HuAECs feeder cells, and Sox2 is a crucial component required for maintenance of them in an undifferentiated, proliferative state capable of self-renewal. Highlights: Black-Right-Pointing-Pointer microRNA-145 inhibits Sox2 expression in human iPS cells. Black-Right-Pointing-Pointer microRNA-145 suppresses the self-renewal and pluripotency of human iPS cells. Black-Right-Pointing-Pointer HuAECs regulate expression of microRNA-145 and Sox2 in human iPS cells. Black-Right-Pointing-Pointer HuAECs feeder

  8. Human amniotic epithelial cell feeder layers maintain human iPS cell pluripotency via inhibited endogenous microRNA-145 and increased Sox2 expression

    International Nuclear Information System (INIS)

    Liu, Te; Cheng, Weiwei; Huang, Yongyi; Huang, Qin; Jiang, Lizhen; Guo, Lihe

    2012-01-01

    Currently, human induced pluripotent stem (iPS) cells were generated from patient or disease-specific sources and share the same key properties as embryonic stem cells. This makes them attractive for personalized medicine, drug screens or cellular therapy. Long-term cultivation and maintenance of normal iPS cells in an undifferentiated self-renewing state are a major challenge. Our previous studies have shown that human amniotic epithelial cells (HuAECs) could provide a good source of feeder cells for mouse and human embryonic stem cells, or spermatogonial stem cells, but the mechanism for this is unknown. Here, we examined the effect of endogenous microRNA-145 regulation on Sox2 expression in human iPS cells by HuAECs feeder cells regulation, and in turn on human iPS cells pluripotency. We found that human IPS cells transfected with a microRNA-145 mutant expressed Sox2 at high levels, allowing iPS to maintain a high level of AP activity in long-term culture and form teratomas in SCID mice. Expression of stem cell markers was increased in iPS transfected with the microRNA-145 mutant, compared with iPS was transfected with microRNA-145. Besides, the expression of Drosha proteins of the microRNA-processor complex, required for the generation of precursor pre-miRNA, was significantly increased in human iPS cells cultured on MEF but not on HuAECs. Taken together, these results suggest that endogenous Sox2 expression may be regulated by microRNA-145 in human iPS cells with HuAECs feeder cells, and Sox2 is a crucial component required for maintenance of them in an undifferentiated, proliferative state capable of self-renewal. Highlights: ► microRNA-145 inhibits Sox2 expression in human iPS cells. ► microRNA-145 suppresses the self-renewal and pluripotency of human iPS cells. ► HuAECs regulate expression of microRNA-145 and Sox2 in human iPS cells. ► HuAECs feeder layers maintain human iPS cells pluripotency. ► HuAECs negatively regulates the synthesis of

  9. Human induced pluripotent stem cells on autologous feeders.

    Directory of Open Access Journals (Sweden)

    Kazutoshi Takahashi

    Full Text Available BACKGROUND: For therapeutic usage of induced Pluripotent Stem (iPS cells, to accomplish xeno-free culture is critical. Previous reports have shown that human embryonic stem (ES cells can be maintained in feeder-free condition. However, absence of feeder cells can be a hostile environment for pluripotent cells and often results in karyotype abnormalities. Instead of animal feeders, human fibroblasts can be used as feeder cells of human ES cells. However, one still has to be concerned about the existence of unidentified pathogens, such as viruses and prions in these non-autologous feeders. METHODOLOGY/PRINCIPAL FINDINGS: This report demonstrates that human induced Pluripotent Stem (iPS cells can be established and maintained on isogenic parental feeder cells. We tested four independent human skin fibroblasts for the potential to maintain self-renewal of iPS cells. All the fibroblasts tested, as well as their conditioned medium, were capable of maintaining the undifferentiated state and normal karyotypes of iPS cells. Furthermore, human iPS cells can be generated on isogenic parental fibroblasts as feeders. These iPS cells carried on proliferation over 19 passages with undifferentiated morphologies. They expressed undifferentiated pluripotent cell markers, and could differentiate into all three germ layers via embryoid body and teratoma formation. CONCLUSIONS/SIGNIFICANCE: These results suggest that autologous fibroblasts can be not only a source for iPS cells but also be feeder layers. Our results provide a possibility to solve the dilemma by using isogenic fibroblasts as feeder layers of iPS cells. This is an important step toward the establishment of clinical grade iPS cells.

  10. Human amniotic epithelial cell feeder layers maintain mouse embryonic stem cell pluripotency via epigenetic regulation of the c-Myc promoter.

    Science.gov (United States)

    Liu, Te; Cheng, Weiwei; Liu, Tianjin; Guo, Lihe; Huang, Qin; Jiang, Lizhen; Du, Xiling; Xu, Fuhui; Liu, Zhixue; Lai, Dongmei

    2010-02-01

    Mouse embryonic stem cells (ESCs) are typically cultured on a feeder layer of mouse embryonic fibroblasts (MEFs), with leukemia inhibitory factor (LIF) added to maintain them in an undifferentiated state. We have previously shown that human amniotic epithelial cells (hAECs) can be used as feeder cells to maintain mouse ESC pluripotency, but the mechanism for this is unknown. In the present study, we found that CpG islands 5' of the c-Myc gene remain hypomethylated in mouse ESCs cultured on hAECs. In addition, levels of acetylation of histone H3 and trimethylation of histone H3K4 in the c-Myc gene promoter were higher in ES cells cultured on hAECs than those in ES cells cultured on MEFs. These data suggested that hAECs can alter mouse ESC gene expression via epigenetic modification of c-Myc, providing a possible mechanism for the hAEC-induced maintenance of ESCs in an undifferentiated state.

  11. Identification of molecules derived from human fibroblast feeder cells that support the proliferation of human embryonic stem cells

    DEFF Research Database (Denmark)

    Anisimov, Sergey V.; Christophersen, Nicolaj S.; Correia, Ana S.

    2011-01-01

    The majority of human embryonic stem cell lines depend on a feeder cell layer for continuous growth in vitro, so that they can remain in an undifferentiated state. Limited knowledge is available concerning the molecular mechanisms that underlie the capacity of feeder cells to support both...... the proliferation and pluripotency of these cells. Importantly, feeder cells generally lose their capacity to support human embryonic stem cell proliferation in vitro following long-term culture. In this study, we performed large-scale gene expression profiles of human foreskin fibroblasts during early...... foreskin fibroblasts to serve as feeder cells for human embryonic stem cell cultures. Among these, the C-KIT, leptin and pigment epithelium-derived factor (PEDF) genes were the most interesting candidates....

  12. Cultivation and irradiation of human fibroblasts in a medium enriched with platelet lysate for obtaining feeder layer in epidermal cell culture; Cultivo e irradiacao de fibroblastos humanos em meio enriquecido com lisado de plaquetas para obtencao de camada de sustentacao em culturas de celulas da epiderme

    Energy Technology Data Exchange (ETDEWEB)

    Yoshito, Daniele

    2011-07-01

    For over 30 years, the use of culture medium, enriched with bovine serum, and murines fibroblasts, with the rate of proliferation controlled by irradiation or by share anticarcinogenic drugs, has been playing successfully its role in assisting in the development of keratinocytes in culture, for clinical purposes. However, currently there is a growing concern about the possibility of transmitting prions and animals viruses to transplanted patients. Taking into account this concern, the present work aims to cultivate human fibroblasts in a medium enriched with human platelets lysate and determine the irradiation dose of these cells, for obtaining feeder layer in epidermal cell culture. For carrying out the proposed objective, platelets lysis has standardized, this lysate was used for human fibroblasts cultivation and the irradiation dose enough to inhibit its duplication was evaluated. Human keratinocytes were cultivated in these feeder layers, in culture medium enriched with the lysate. With these results we conclude that the 10% platelets lysate promoted a better adhesion and proliferation of human fibroblasts and in all dose levels tested (60 to 300 Gy), these had their mitotic activity inactivated by ionizing irradiation, being that the feeder layers obtained with doses from 70 to 150 Gy were those that provided the best development of keratinocytes in medium containing 2.5% of human platelet lysate. Therefore, it was possible to standardize both the cultivation of human fibroblasts as its inactivation for use as feeder layer in culture of keratinocytes, so as to eliminate xenobiotics components. (author)

  13. Developmental Competence of Buffalo (Bubalus bubalis) Pluripotent Embryonic Stem Cells Over Different Homologous Feeder Layers and the Comparative Evaluation with Various Extracellular Matrices.

    Science.gov (United States)

    Sharma, Manjinder; Dubey, Pawan K; Kumar, Rajesh; Nath, Amar; Kumar, G Sai; Sharma, G Taru

    2013-05-01

    Use of somatic cells as a feeder layer to maintain the embryonic stem cells (ESCs) in undifferentiated state limits the stem cell research design, since experimental data may result from a combined ESCs and feeder cell response to various stimuli. Therefore, present study was designed to evaluate the developmental competence of the buffalo ESCs over different homogenous feeders and compare with various extracellular matrices using different concentrations of LIF. Inner cell masses (ICMs) of in vitro hatched blastocysts were cultured onto homologous feeders viz. fetal fibroblast, granulosa and oviductal cell feeder layers and synthetic matrices viz. fibronectin, collagen type I and matrigel in culture medium. Developmental efficiency was found higher for ESCs cultured on fetal fibroblast and granulosa layers (83.33%) followed by fibronectin (77.78%) at 30 ng LIF. Oviductal feeder was found to be the least efficient feeder showing only 11.11% undifferentiated primary ESC colonies at 30 ng LIF. However, neither feeder layer nor synthetic matrix could support the development of primary colonies at 10 ng LIF. Expression of SSEA- 4, TRA-1-60 and Oct-4 were found positive in ESC colonies from all the feeders and synthetic matrices with 20 ng and 30 ng LIF. Fetal fibroblast and granulosa cell while, amongst synthetic matrices, fibronectin were found to be equally efficient to support the growth and maintenance of ESCs pluripotency with 30 ng LIF. This well-defined culture conditions may provide an animal model for culturing human embryonic stem cells in the xeno-free or feeder-free conditions for future clinical applications.

  14. Expression and secretory profile of buffalo fetal fibroblasts and Wharton's jelly feeder layers.

    Science.gov (United States)

    Parmar, Mehtab S; Mishra, Smruti Ranjan; Somal, Anjali; Pandey, Sriti; Kumar, G Sai; Sarkar, Mihir; Chandra, Vikash; Sharma, G Taru

    2017-05-01

    The present study examined the comparative expression and secretory profile of vital signaling molecules in buffalo fetal fibroblasts (BFF) and Wharton's jelly (BWJ) feeder layers at different passages. Both feeder layers were expanded up to 8th passage. Signaling molecules viz. bone morphogenetic protein 4 (BMP4), fibroblast growth factor 2 (FGF2), leukemia inhibitory factor (LIF) and transforming growth factor beta 1 (TGFB1) and pluripotency-associated transcriptional factors (POU5F1, SOX2, NANOG, KLF4, MYC and FOXD3) were immunolocalized in the both feeder types. A clear variation in the expression pattern of key signaling molecules with passaging was registered in both feeders compared to primary culture (0 passage). The conditioned media (CM) was collected from different passages (2, 4, 6, 8) of both the feeder layers and was quantified using enzyme-linked immunosorbent assay (ELISA). Concomitant to expression profile, protein quantification also revealed differences in the concentration of signaling molecules at different time points. Conjointly, expression and secretory profile revealed that 2nd passage of BFF and 6th passage of BWJ exhibit optimal levels of key signaling molecules thus may be selected as best passages for embryonic stem cells (ESCs) propagation. Further, the effect of mitomycin-C (MMC) treatment on the expression profile of signaling molecules in the selected passages of BFF and BWJ revealed that MMC modulates the expression profile of these molecules. In conclusion, the results indicate that feeder layers vary in expression and secretory pattern of vital signaling molecules with passaging. Based on these findings, the appropriate feeder passages may be selected for the quality propagation of buffalo ESCs. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Effects of different feeder layers on culture of bovine embryonic stem cell-like cells in vitro.

    Science.gov (United States)

    Cong, Shan; Cao, Guifang; Liu, Dongjun

    2014-12-01

    To find a suitable feeder layer is important for successful culture conditions of bovine embryonic stem cell-like cells. In this study, expression of pluripotency-related genes OCT4, SOX2 and NANOG in bovine embryonic stem cell-like cells on mouse embryonic fibroblast feeder layers at 1-5 passages were monitored in order to identify the possible reason that bovine embryonic stem cell-like cells could not continue growth and passage. Here, we developed two novel feeder layers, mixed embryonic fibroblast feeder layers of mouse and bovine embryonic fibroblast at different ratios and sources including mouse fibroblast cell lines. The bovine embryonic stem cell-like cells generated in our study displayed typical stem cell morphology and expressed specific markers such as OCT4, stage-specific embryonic antigen 1 and 4, alkaline phosphatase, SOX2, and NANOG mRNA levels. When feeder layers and cell growth factors were removed, the bovine embryonic stem cell-like cells formed embryoid bodies in a suspension culture. Furthermore, we compared the expression of the pluripotent markers during bovine embryonic stem cell-like cell in culture on mixed embryonic fibroblast feeder layers, including mouse fibroblast cell lines feeder layers and mouse embryonic fibroblast feeder layers by real-time quantitative polymerase chain reaction. Results suggested that mixed embryonic fibroblast and sources including mouse fibroblast cell lines feeder layers were more suitable for long-term culture and growth of bovine embryonic stem cell-like cells than mouse embryonic fibroblast feeder layers. The findings may provide useful experimental data for the establishment of an appropriate culture system for bovine embryonic stem cell lines.

  16. A reliable and economical method for gaining mouse embryonic fibroblasts capable of preparing feeder layers.

    Science.gov (United States)

    Jiang, Guangming; Wan, Xiaoju; Wang, Ming; Zhou, Jianhua; Pan, Jian; Wang, Baolong

    2016-08-01

    Mouse embryonic fibroblasts (MEFs) are widely used to prepare feeder layers for culturing embryonic stem cells (ESCs) or induced pluripotent stem cells (iPSCs) in vitro. Transportation lesions and exorbitant prices make the commercially obtained MEFs unsuitable for long term research. The aim of present study is to establish a method, which enables researchers to gain MEFs from mice and establish feeder layers by themselves in ordinary laboratories. MEFs were isolated from ICR mouse embryos at 12.5-17.5 day post-coitum (DPC) and cultured in vitro. At P2-P7, the cells were inactivated with mitomycin C or by X-ray irradiation. Then they were used to prepare feeder layers. The key factors of the whole protocol were analyzed to determine the optimal conditions for the method. The results revealed MEFs isolated at 12.5-13.5 DPC, and cultured to P3 were the best choice for feeder preparation, those P2 and P4-P5 MEFs were also suitable for the purpose. The P3-P5 MEFs treated with 10 μg/ml of mitomycin C for 3 h, or irradiated with X-ray at 1.5 Gy/min for 25 Gy were the most suitable feeder cells. Treating MEFs with 10 μg/ml of mitomycin C for 2.5 h, 15 μg/ml for 2.0 h, or irradiating the cells with 20 Gy of X-ray at 2.0 Gy/min could all serve as alternative methods for P3-P4 cells. Our study provides a reliable and economical way to obtain large amount of qualified MEFs for long term research of ESCs or iPSCs.

  17. Effects of different feeder layers on culture of bovine embryonic stem cell-like cells in vitro

    OpenAIRE

    Cong, Shan; Cao, Guifang; Liu, Dongjun

    2014-01-01

    To find a suitable feeder layer is important for successful culture conditions of bovine embryonic stem cell-like cells. In this study, expression of pluripotency-related genes OCT4, SOX2 and NANOG in bovine embryonic stem cell-like cells on mouse embryonic fibroblast feeder layers at 1–5 passages were monitored in order to identify the possible reason that bovine embryonic stem cell-like cells could not continue growth and passage. Here, we developed two novel feeder layers, mixed embryonic ...

  18. Derivation and characterization of the NIH registry human stem cell line NYSCF100 line under defined feeder-free conditions

    Directory of Open Access Journals (Sweden)

    Ana Sevilla

    2018-05-01

    Full Text Available The human embryonic stem cell line NYSCFe001-A was derived from a day 6 blastocyst in feeder-free and antibiotic free conditions. The blastocyst was voluntarily donated for research as surplus after in vitro fertilization treatment following informed consent. The NYSCFe001-A line, registered as NYSCF100 on the NIH registry, presents normal karyotype, is mycoplasma free, expresses all the pluripotency markers and has the potential to differentiate into all three germ layers in vitro.

  19. Effects of Feeder Cells on Dopaminergic Differentiation of Human Embryonic Stem Cells

    Directory of Open Access Journals (Sweden)

    Zhenqiang Zhao

    2016-12-01

    Full Text Available Mouse embryonic fibroblasts (MEFs and human foreskin fibroblasts (HFFs are used for the culture of human embryonic stem cells (hESCs. MEFs and HFFs differed in their capacity to support the proliferation and pluripotency of hESCs and could affect cardiac differentiation potential of hESCs. The aim of this study was to evaluate the effect of MEFs and HFFs feeders on dopaminergic differentiation of hESCs lines. To minimize the impact of culture condition variation, two hESCs lines were cultured on mixed feeder cells (MFCs, MEFs: HFFs =1:1 and HFFs feeder respectively, and then were differentiated into DA neurons under the identical protocol. Dopaminergic differentiation was evaluated by immunocytochemistry, quantitative fluorescent real-time PCR (qRT-PCR, transmission and scanning electron microscopy, and patch clamp. Our results demonstrated that these hESCs-derived neurons were genuine and functional DA neurons. However, compared to hESCs line on MFCs feeder, hESCs line on HFFs feeder had a higher proportion of TH positive cells and expressed higher levels of FOXA2, PITX3, NURR1 and TH genes. In addition, the values of threshold intensity and threshold membrane potential of DA neurons from hESCs line on HFFs feeder were lower than those of DA neurons from hESCs line on the MFCs feeder. In conclusion, HFFs feeder not only facilitated the differentiation of hESCs cells into dopaminergic neurons, but also induced hESCs-derived DA neurons to express higher electrophysiological excitability. Therefore, feeder cells could affect not only dopaminergic differentiation potential of different hESCs lines, but also electrophysiological properties of hESCs-derived DA neurons.

  20. A feeder-free, human plasma-derived hydrogel for maintenance of a human embryonic stem cell phenotype in vitro

    Directory of Open Access Journals (Sweden)

    Lewis Fiona C

    2012-08-01

    Full Text Available Abstract Background Human embryonic stem cells (hESCs represent a tremendous resource for cell therapies and the study of human development; however to maintain their undifferentiated state in vitro they routinely require the use of mouse embryonic fibroblast (MEF feeder-layers and exogenous protein media supplementation. Results These well established requirements can be overcome and in this study, it will be demonstrated that phenotypic stability of hESCs can be maintained using a novel, human plasma protein-based hydrogel as an extracellular culture matrix without the use of feeder cell co-culture. hESCs were resuspended in human platelet poor plasma (PPP, which was gelled by the addition of calcium containing DMEM-based hESC culture medium. Phenotypic and genomic expression of the pluripotency markers OCT4, NANOG and SOX2 were measured using immunohistochemistry and qRT-PCR respectively. Typical hESC morphology was demonstrated throughout in vitro culture and both viability and phenotypic stability were maintained throughout extended culture, up to 25 passages. Conclusions PPP-derived hydrogel has demonstrated to be an efficacious alternative to MEF co-culture with its hydrophilicity allowing for this substrate to be delivered via minimally invasive procedures in a liquid phase with polymerization ensuing in situ. Together this provides a novel technique for the study of this unique group of stem cells in either 2D or 3D both in vitro and in vivo.

  1. Establishment of rat embryonic stem-like cells from the morula using a combination of feeder layers.

    Science.gov (United States)

    Sano, Chiaki; Matsumoto, Asako; Sato, Eimei; Fukui, Emiko; Yoshizawa, Midori; Matsumoto, Hiromichi

    2009-08-01

    Embryonic stem (ES) cells are characterized by pluripotency, in particular the ability to form a germline on injection into blastocysts. Despite numerous attempts, ES cell lines derived from rat embryos have not yet been established. The reason for this is unclear, although certain intrinsic biological differences among species and/or strains have been reported. Herein, using Wistar-Imamichi rats, specific characteristics of preimplantation embryos are described. At the blastocyst stage, Oct4 (also called Pou5f1) was expressed in both the inner cell mass (ICM) and the trophectoderm (TE), whereas expression of Cdx2 was localized to the TE. In contrast, at an earlier stage, expression of Oct4 was detected in all the nuclei in the morula. These stages were examined using a combination of feeder layers (rat embryonic fibroblast [REF] for primary outgrowth and SIM mouse embryo-derived thioguanine- and ouabain-resistant [STO] cells for passaging) to establish rat ES-like cell lines. The rat ES-like cell lines obtained from the morula maintained expression of Oct4 over long-term culture, whereas cell lines derived from blastocysts lost pluripotency during early passage. The morula-derived ES-like cell lines showed Oct4 expression in a long-term culture, even after cryogenic preservation, thawing and EGFP transfection. These results indicate that rat ES-like cell lines with long-term Oct4 expression can be established from the morula of Wistar-Imamichi rats using a combination of feeder layers.

  2. Tumorigenic risk of human induced pluripotent stem cell explants cultured on mouse SNL76/7 feeder cells

    Energy Technology Data Exchange (ETDEWEB)

    Kamada, Mizuna; Mitsui, Youji, E-mail: y-mitsui8310@hb.tp1.jp; Kumazaki, Tsutomu; Kawahara, Yuta; Matsuo, Taira; Takahashi, Tomoko, E-mail: t-takahashi@kph.bunri-u.ac.jp

    2014-10-24

    Highlights: • hiPS cell explants formed malignant tumors when SNL76/7 feeder cells were used. • Multi type tumors developed by interaction of SNL76/7 feeder cells with hiPS cells. • Tumorigenic risk occurs by co-culture of hiPS cells with SNL76/7 feeder cells. - Abstract: The potential for tumor formation from transplanted human induced pluripotent stem cell (hiPSC) derivatives represents a high risk in their application to regenerative medicine. We examined the genetic origin and characteristics of tumors, that were formed when 13 hiPSC lines, established by ourselves, and 201B7 hiPSC from Kyoto University were transplanted into severe combined immune-deficient (SCID) mice. Though teratomas formed in 58% of mice, five angiosarcomas, one malignant solitary fibrous tumor and one undifferentiated pleomorphic sarcoma formed in the remaining mice. Three malignant cell lines were established from the tumors, which were derived from mitomycin C (MMC)-treated SNL76/7 (MMC-SNL) feeder cells, as tumor development from fusion cells between MMC-SNL and hiPSCs was negative by genetic analysis. While parent SNL76/7 cells produced malignant tumors, neither MMC-SNL nor MMC-treated mouse embryo fibroblast (MEF) produced malignant tumors. When MMC-SNL feeder cells were co-cultured with hiPSCs, growing cell lines were generated, that expressed genes similar to the parent SNL76/7 cells. Thus, hiPSCs grown on MMC-SNL feeder cells have a high risk of generating feeder-derived malignant tumors. The possible mechanism(s) of growth restoration and the formation of multiple tumor types are discussed with respect of the interactions between MMC-SNL and hiPSC.

  3. Growth factor expression pattern of homologous feeder layer for culturing buffalo embryonic stem cell-like cells.

    Science.gov (United States)

    Sharma, Ruchi; George, Aman; Kamble, Nitin M; Chauhan, Manmohan S; Singla, Suresh; Manik, Radhey S; Palta, Prabhat

    2012-01-01

    The present study examined the expression profile of buffalo fetal fibroblasts (BFF) used as a feeder layer for embryonic stem (ES) cell-like cells. The expression of important growth factors was detected in cells at different passages. Mitomycin-C inactivation increased relative expression levels of ACTIVIN-A, TGF-β1, BMP-4 and GREMLIN but not of fibroblast growth factor-2 (FGF-2). The expression level of ACTIVIN-A, transforming growth factor-β1 (TGF-β1), bone morphogenetic protein-4 (BMP-4) and FGF-2 was similar in buffalo fetal fibroblast (BFF) cultured in stem cell medium (SCM), SCM+1000IU mL(-1) leukemia inhibitory factor (LIF), SCM+5 ngmL(-1) FGF-2 or SCM+LIF+FGF-2 for 24 h whereas GREMLIN expression was higher in FGF-2-supplemented groups. In spent medium, the concentration of ACTIVIN-A was higher in FGF-2-supplemented groups whereas that of TGF-β1 was similar in SCM and LIF+FGF-2, which was higher than when either LIF or FGF-2 was used alone. Following culture of ES cell-like cells on a feeder layer for 24 h, the TGF-β1 concentration was higher with LIF+FGF-2 than with LIF or FGF-2 alone which, in turn, was higher than that in SCM. In the LIF+FGF-2 group, the concentration of TGF-β1 was lower and that of ACTIVIN-A was higher in spent medium at 24 h than at 48 h of culture. These results suggest that BFF produce signalling molecules that may help in self-renewal of buffalo ES cell-like cells.

  4. A feeder- and xeno-free human induced pluripotent stem cell line obtained from primary human dermal fibroblasts with epigenetic repression of reprogramming factors expression: GPCCi001-A

    Directory of Open Access Journals (Sweden)

    Michał Stefan Lach

    2017-04-01

    Full Text Available The primary human dermal fibroblasts (PHDFs from breast cancer patient were obtained to generate the human induced pluripotent stem cell line GPCCi001-A via lentiviral transfection. Thus, a modified EF1a-hSTEMCCA-loxP with tetO operator which regulates transgene expression was used. This method takes advantage of epigenetic regulation of transcription and allows for stable silencing of the reprogramming factors in obtained hiPS cells. To increase the potential utility of hiPSCs for clinical applications, they were adapted to feeder- and xeno-free conditions. The pluripotency of GPCCi001-A cell line and ability to differentiate into three germ layers was confirmed.

  5. Comparison of the Ex Vivo Expansion of UCB-Derived CD34+ in 3D DBM/MBA Scaffolds with USSC as a Feeder Layer.

    Science.gov (United States)

    Sadat Hashemi, Zahra; Forouzandeh Moghadam, Mahdi; Soleimani, Masoud

    2013-10-01

    Ex vivo expansion of hematopoitic stem cells is an alternative way to increase umbilical cord blood (UCB)-CD34+ cells for bone marrow transplantation. For this purpose demineralized bone matrix (DBM) and mineralized bone allograft (MBA) as two scaffolds based on bone matrix and stem cell niche, were simultaneously used to enhance the effect of human mesenchymal progenitor cells (MPCs) - unrestricted somatic stem cells (USSCs) - as a feeder layer. USSCs were isolated and characterized by morphological and immunological analysis then seeded on both scaffolds as a feeder layer. UCB-CD34(+) were isolated by MACS method and were co-culture expanded by USSC in 3D and 2D environments. After 3 weeks expansion, cells were counted and were assessed by karyotype, flow cytometry, clonogenic activity, and long-term culture-initiating cells (LTC-IC). Co-culture expansion in DBM and MBA was 29.22-fold and 27.77-fold, no significant differences in colony and LTC-IC were obtained. Maximum number of colonies belonged to the day 14 with the 73% CFU-GM (Colony Forming Unit- Granulocyte/Macrophage) in contrast to the day 0 which was BFU-E/CFU-E (Burst/Colony Forming Unit-Erythroid). Flow cytometry indicated that the percentage of CD34+ marker was decreased in USSC co-culture and the highest percentage was observed in simple 2D culture. Because of acid extraction in the DBM production process, mineral materials were removed and the protein background that was more flexible was presented. Therefore these results suggest that USSC-DBM can be a suitable ex vivo mimicry niche by intensifying of surface/volume ratio and supporting the stem cell differentiation and expansion.

  6. Establishment of feeder-free culture system for human induced pluripotent stem cell on DAS nanocrystalline graphene

    Science.gov (United States)

    Lee, Hyunah; Nam, Donggyu; Choi, Jae-Kyung; Araúzo-Bravo, Marcos J.; Kwon, Soon-Yong; Zaehres, Holm; Lee, Taehee; Park, Chan Young; Kang, Hyun-Wook; Schöler, Hans R.; Kim, Jeong Beom

    2016-02-01

    The maintenance of undifferentiated human pluripotent stem cells (hPSC) under xeno-free condition requires the use of human feeder cells or extracellular matrix (ECM) coating. However, human-derived sources may cause human pathogen contamination by viral or non-viral agents to the patients. Here we demonstrate feeder-free and xeno-free culture system for hPSC expansion using diffusion assisted synthesis-grown nanocrystalline graphene (DAS-NG), a synthetic non-biological nanomaterial which completely rule out the concern of human pathogen contamination. DAS-NG exhibited advanced biocompatibilities including surface nanoroughness, oxygen containing functional groups and hydrophilicity. hPSC cultured on DAS-NG could maintain pluripotency in vitro and in vivo, and especially cell adhesion-related gene expression profile was comparable to those of cultured on feeders, while hPSC cultured without DAS-NG differentiated spontaneously with high expression of somatic cell-enriched adhesion genes. This feeder-free and xeno-free culture method using DAS-NG will facilitate the generation of clinical-grade hPSC.

  7. A feeder-free culture using autogeneic conditioned medium for undifferentiated growth of human embryonic stem cells: Comparative expression profiles of mRNAs, microRNAs and proteins among different feeders and conditioned media

    Directory of Open Access Journals (Sweden)

    Chou Chi-Hsien

    2010-10-01

    Full Text Available Abstract Background Human embryonic stem (hES cell lines were derived from the inner cell mass of human blastocysts, and were cultured on mouse embryonic fibroblast (MEF feeder to maintain undifferentiated growth, extensive renewal capacity, and pluripotency. The hES-T3 cell line with normal female karyotype was previously used to differentiate into autogeneic fibroblast-like cells (T3HDF as feeder to support the undifferentiated growth of hES-T3 cells (T3/HDF for 14 passages. Results A feeder-free culture on Matrigel in hES medium conditioned by the autogeneic feeder cells (T3HDF was established to maintain the undifferentiated growth of hES-T3 cells (T3/CMHDF for 8 passages in this investigation. The gene expression profiles of mRNAs, microRNAs and proteins between the undifferentiated T3/HDF and T3/CMHDF cells were shown to be very similar, and their expression profiles were also found to be similar to those of T3/MEF and T3/CMMEF cells grown on MEF feeder and feeder-free Matrigel in MEF-conditioned medium, respectively. The undifferentiated state of T3/HDF and T3/CMHDF as well as T3/MEF andT3/CMMEF cells was evidenced by the very high expression levels of "stemness" genes and low expression levels of differentiation markers of ectoderm, mesoderm and endoderm in addition to the strong staining of OCT4 and NANOG. Conclusion The T3HDF feeder and T3HDF-conditioned medium were able to support the undifferentiated growth of hES cells, and they would be useful for drug development and toxicity testing in addition to the reduced risks of xenogeneic pathogens when used for medical applications such as cell therapies.

  8. Using Human Gestures and Generic Skills to Instruct a Mobile Robot Arm in a Feeder Filling Scenario

    DEFF Research Database (Denmark)

    Pedersen, Mikkel Rath; Høilund, Carsten; Krüger, Volker

    2012-01-01

    Mobile robots that have the ability to cooperate with humans are able to provide new possibilities to manufac- turing industries. In this paper, we discuss our mobile robot arm that a) can provide assistance at different locations in a factory and b) that can be programmed using complex human...... actions such as pointing in Take this object. In this paper, we discuss the use of the mobile robot for a feeding scenario where a human operator specifies the parts and the feeders through pointing gestures. The system is partially built using generic robotic skills. Through extensive experiments, we...

  9. Easy xeno-free and feeder-free method for isolating and growing limbal stromal and epithelial stem cells of the human cornea.

    Directory of Open Access Journals (Sweden)

    Djida Ghoubay-Benallaoua

    Full Text Available Epithelial and stromal stem cells are required to maintain corneal transparency. The aim of the study was to develop a new method to isolate and grow both corneal stromal (SSC and epithelial limbal (LSC stem cells from small human limbal biopsies under culture conditions in accordance with safety requirements mandatory for clinical use in humans. Superficial limbal explants were retrieved from human donor corneo-scleral rims. Human limbal cells were dissociated by digestion with collagenase A, either after epithelial scraping or with no scraping. Isolated cells were cultured with Essential 8 medium (E8, E8 supplemented with EGF (E8+ or Green's medium with 3T3 feeder-layers. Cells were characterized by immunostaining, RT-qPCR, colony forming efficiency, sphere formation, population doubling, second harmonic generation microscopy and differentiation potentials. LSC were obtained from unscraped explants in E8, E8+ and Green's media and were characterized by colony formation and expression of PAX6, ΔNP63α, Bmi1, ABCG2, SOX9, CK14, CK15 and vimentin, with a few cells positive for CK3. LSC underwent 28 population doublings still forming colonies. SSC were obtained from both scraped and unscraped explants in E8 and E8+ media and were characterized by sphere formation, expression of PAX6, SOX2, BMI1, NESTIN, ABCG2, KERATOCAN, VIMENTIN, SOX9, SOX10 and HNK1, production of collagen fibrils and differentiation into keratocytes, fibroblasts, myofibroblasts, neurons, adipocytes, chondrocytes and osteocytes. SSC underwent 48 population doublings still forming spheres, Thus, this new method allows both SSC and LSC to be isolated from small superficial limbal biopsies and to be primary cultured in feeder-free and xeno-free conditions, which will be useful for clinical purposes.

  10. Immunoflourescence and mRNA analysis of human embryonic stem cells (hESCs) grown under feeder-free conditions

    DEFF Research Database (Denmark)

    Awan, Aashir; Oliveri, Roberto S; Jensen, Pernille L

    2010-01-01

    onto 16-well glass chambers, and continuing with the general IF and qPCR steps will be provided. The techniques will be illustrated with new results on cellular localization of transcriptional factors and components of the Hedgehog, Wnt, and PDGF signaling pathways to primary cilia in stem cell......This chapter describes the procedures in order to do immunofluorescence (IF) microscopy and quantitative PCR (qPCR) analysis of human embryonic stem cells (hESCs) grown specifically under feeder-free conditions. A detailed protocol outlining the steps from initially growing the cells, passaging...

  11. CATTLE FEEDER BEHAVIOR AND FEEDER CATTLE PLACEMENTS

    OpenAIRE

    Kastens, Terry L.; Schroeder, Ted C.

    1994-01-01

    Cattle feeders appear irrational when they place cattle on feed when projected profit is negative. Long futures positions appear to offer superior returns to cattle feeding investment. Cattle feeder behavior suggests that they believe a downward bias in live cattle futures persists and that cattle feeders use different expectations than the live cattle futures market price when making placement decisions. This study examines feeder cattle placement determinants, comparing performance of expec...

  12. Induced pluripotent stem cells generated from human adipose-derived stem cells using a non-viral polycistronic plasmid in feeder-free conditions.

    Directory of Open Access Journals (Sweden)

    Xinjian Qu

    Full Text Available Induced pluripotent stem cells (iPSCs can be generated from somatic cells by ectopic expression of defined transcription factors (TFs. However, the optimal cell type and the easy reprogramming approaches that minimize genetic aberrations of parent cells must be considered before generating the iPSCs. This paper reports a method to generate iPSCs from adult human adipose-derived stem cells (hADSCs without the use of a feeder layer, by ectopic expression of the defined transcription factors OCT4, SOX2, KLF4 and C-MYC using a polycistronic plasmid. The results, based on the expression of pluripotent marker, demonstrated that the iPSCs have the characteristics similar to those of embryonic stem cells (ESCs. The iPSCs differentiated into three embryonic germ layers both in vitro by embryoid body generation and in vivo by teratoma formation after being injected into immunodeficient mice. More importantly, the plasmid DNA does not integrate into the genome of human iPSCs as revealed by Southern blotting experiments. Karyotypic analysis also demonstrated that the reprogramming of hADSCs by the defined factors did not induce chromosomal abnormalities. Therefore, this technology provides a platform for studying the biology of iPSCs without viral vectors, and can hopefully overcome immune rejection and ethical concerns, which are the two important barriers of ESC applications.

  13. Efficient generation of transgene- and feeder-free induced pluripotent stem cells from human dental mesenchymal stem cells and their chemically defined differentiation into cardiomyocytes.

    Science.gov (United States)

    Tan, Xiaobing; Dai, Qingli; Guo, Tao; Xu, Jingshu; Dai, Qingyuan

    2018-01-22

    Advance in stem cell research resulted in several processes to generate induced pluripotent stem cells (iPSCs) from adult somatic cells. In our previous study, the reprogramming of iPSCs from human dental mesenchymal stem cells (MSCs) including SCAP and DPSCs, has been reported. Herein, safe iPSCs were reprogrammed from SCAP and DPSCs using non-integrating RNA virus vector, which is an RNA virus carrying no risk of altering host genome. DPSCs- and SCAP-derived iPSCs exhibited the characteristics of the classical morphology with human embryonic stem cells (hESCs) without integration of foreign genes, indicating the potential of their clinical application. Moreover, induced PSCs showed the capacity of self-renewal and differentiation into cardiac myocytes. We have achieved the differentiation of hiPSCs to cardiomyocytes lineage under serum and feeder-free conditions, using a chemically defined medium CDM3. In CDM3, hiPSCs differentiation is highly generating cardiomyocytes. The results showed this protocol produced contractile sheets of up to 97.2% TNNT2 cardiomyocytes after purification. Furthermore, derived hiPSCs differentiated to mature cells of the three embryonic germ layers in vivo and in vitro of beating cardiomyocytes. The above whole protocol enables the generation of large scale of highly pure cardiomyocytes as needed for cellular therapy. Copyright © 2017. Published by Elsevier Inc.

  14. Neural stem cells achieve and maintain pluripotency without feeder cells.

    Directory of Open Access Journals (Sweden)

    Hyun Woo Choi

    Full Text Available BACKGROUND: Differentiated cells can be reprogrammed into pluripotency by transduction of four defined transcription factors. Induced pluripotent stem cells (iPS cells are expected to be useful for regenerative medicine as well as basic research. Recently, the report showed that mouse embryonic fibroblasts (MEF cells are not essential for reprogramming. However, in using fibroblasts as donor cells for reprogramming, individual fibroblasts that had failed to reprogram could function as feeder cells. METHODOLOGY/PRINCIPAL FINDING: Here, we show that adult mouse neural stem cells (NSCs, which are not functional feeder cells, can be reprogrammed into iPS cells using defined four factors (Oct4, Sox2, Klf4, and c-Myc under feeder-free conditions. The iPS cells, generated from NSCs expressing the Oct4-GFP reporter gene, could proliferate for more than two months (passage 20. Generated and maintained without feeder cells, these iPS cells expressed pluripotency markers (Oct4 and Nanog, the promoter regions of Oct4 and Nanog were hypomethylated, could differentiated into to all three germ layers in vitro, and formed a germline chimera. These data indicate that NSCs can achieve and maintain pluripotency under feeder-free conditions. CONCLUSION/SIGNIFICANCE: This study suggested that factors secreted by feeder cells are not essential in the initial/early stages of reprogramming and for pluripotency maintenance. This technology might be useful for a human system, as a feeder-free reprogramming system may help generate iPS cells of a clinical grade for tissue or organ regeneration.

  15. Generation of megakaryocytic progenitors from human embryonic stem cells in a feeder- and serum-free medium.

    Directory of Open Access Journals (Sweden)

    Marjorie Pick

    Full Text Available BACKGROUND: The production of human platelets from embryonic stem cells in a defined culture system is a prerequisite for the generation of platelets for therapeutic use. As an important step towards this goal, we report the differentiation of human embryonic stem cells (hESCs towards the megakaryocyte (Mk lineage using a 'spin embryoid body' method in serum-free differentiation medium. METHODOLOGY AND PRINCIPAL FINDINGS: Immunophenotypic analyses of differentiating hESC identified a subpopulation of cells expressing high levels of CD41a that expressed other markers associated with the Mk lineage, including CD110, CD42b and CD61. Differentiated cells were sorted on the basis of their expression of CD41a, CD34 and CD45 and assessed for Mk colony formation, expression of myeloid and Mk genes and ability to endoreplicate DNA. In a collagen-based colony assay, the CD41a⁺ cells sorted from these differentiation cultures produced 100-800 Mk progenitors at day 13 and 25-160 Mk progenitors at day 20 of differentiation per 100,000 cells assayed. Differentiated Mk cells produced platelet-like particles which expressed CD42b and were activated by ADP, similar to platelets generated from precursors in cord blood. These studies were complemented by real time PCR analyses showing that subsets of cells enriched for CD41a⁺ Mk precursors expressed high levels of Mk associated genes such as PF4 and MPL. Conversely, high levels of myeloid and erythroid related transcripts, such as GATA1, TAL1/SCL and PU.1, were detected in sorted fractions containing CD34⁺ and CD45⁺ cells. CONCLUSIONS: We describe a serum- and feeder-free culture system that enabled the generation of Mk progenitors from human embryonic stem cells. These cells formed colonies that included differentiated Mks that fragmented to form platelet-like particles. This protocol represents an important step towards the generation of human platelets for therapeutic use.

  16. Design of apron feeders

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, C.M.

    1987-12-01

    This paper discusses practical aspects of apron feeder design, and includes information on how to make the first selection. Various aspects of design such as feeder speed, material depth, chain-pitch, roller loading, wheels/sprockets and chain roller friction are elaborated in detail. 8 refs., 14 figs., 12 tabs.

  17. "The good into the pot, the bad into the crop!"--a new technology to free stem cells from feeder cells.

    Directory of Open Access Journals (Sweden)

    Annette Schneider

    Full Text Available A variety of embryonic and adult stem cell lines require an initial co-culturing with feeder cells for non-differentiated growth, self renewal and maintenance of pluripotency. However for many downstream ES cell applications the feeder cells have to be considered contaminations that might interfere not just with the analysis of experimental data but also with clinical application and tissue engineering approaches. Here we introduce a novel technique that allows for the selection of pure feeder-freed stem cells, following stem cell proliferation on feeder cell layers. Complete and reproducible separation of feeder and embryonic stem cells was accomplished by adaptation of an automated cell selection system that resulted in the aspiration of distinct cell colonies or fraction of colonies according to predefined physical parameters. Analyzing neuronal differentiation we demonstrated feeder-freed stem cells to exhibit differentiation potentials comparable to embryonic stem cells differentiated under standard conditions. However, embryoid body growth as well as differentiation of stem cells into cardiomyocytes was significantly enhanced in feeder-freed cells, indicating a feeder cell dependent modulation of lineage differentiation during early embryoid body development. These findings underline the necessity to separate stem and feeder cells before the initiation of in vitro differentiation. The complete separation of stem and feeder cells by this new technology results in pure stem cell populations for translational approaches. Furthermore, a more detailed analysis of the effect of feeder cells on stem cell differentiation is now possible, that might facilitate the identification and development of new optimized human or genetically modified feeder cell lines.

  18. Feederism in a woman.

    Science.gov (United States)

    Terry, Lesley L; Vasey, Paul L

    2011-06-01

    Feederism is a fat fetish subculture in which individuals eroticize weight gain and feeding. Feeders are individuals who claim to become sexually aroused by feeding their partners and encouraging them to gain weight. Conversely, Feedees are individuals who claim to become sexually aroused by eating, being fed, and the idea or act of gaining weight. Very little is known about this population. This report describes a woman who self-identified as a Feedee. It is unclear, at present, whether female Feederism represents a unique paraphilia or a thematic variation of morphophilia or sexual masochism.

  19. Robust and highly-efficient differentiation of functional monocytic cells from human pluripotent stem cells under serum- and feeder cell-free conditions.

    Directory of Open Access Journals (Sweden)

    Masakatsu D Yanagimachi

    Full Text Available Monocytic lineage cells (monocytes, macrophages and dendritic cells play important roles in immune responses and are involved in various pathological conditions. The development of monocytic cells from human embryonic stem cells (ESCs and induced pluripotent stem cells (iPSCs is of particular interest because it provides an unlimited cell source for clinical application and basic research on disease pathology. Although the methods for monocytic cell differentiation from ESCs/iPSCs using embryonic body or feeder co-culture systems have already been established, these methods depend on the use of xenogeneic materials and, therefore, have a relatively poor-reproducibility. Here, we established a robust and highly-efficient method to differentiate functional monocytic cells from ESCs/iPSCs under serum- and feeder cell-free conditions. This method produced 1.3 × 10(6 ± 0.3 × 10(6 floating monocytes from approximately 30 clusters of ESCs/iPSCs 5-6 times per course of differentiation. Such monocytes could be differentiated into functional macrophages and dendritic cells. This method should be useful for regenerative medicine, disease-specific iPSC studies and drug discovery.

  20. Dry piston coal feeder

    Science.gov (United States)

    Hathaway, Thomas J.; Bell, Jr., Harold S.

    1979-01-01

    This invention provides a solids feeder for feeding dry coal to a pressurized gasifier at elevated temperatures substantially without losing gas from the gasifier by providing a lock having a double-acting piston that feeds the coals into the gasifier, traps the gas from escaping, and expels the trapped gas back into the gasifier.

  1. Feeder replacement tooling and processes

    International Nuclear Information System (INIS)

    Mallozzi, R.; Goslin, R.; Pink, D.; Askari, A.

    2008-01-01

    Primary heat transport system feeder integrity has become a concern at some CANDU nuclear plants as a result of thinning caused by flow accelerated corrosion (FAC). Feeder inspections are indicating that life-limiting wall thinning can occur in the region between the Grayloc hub weld and second elbow of some outlet feeders. In some cases it has become necessary to replace thinned sections of affected feeders to restore feeder integrity to planned end of life. Atomic Energy of Canada Limited (AECL) and Babcock and Wilcox Canada Ltd. (B and W) have developed a new capability for replacement of single feeders at any location on the reactor face without impacting or interrupting operation of neighbouring feeders. This new capability consists of deploying trained crews with specialized tools and procedures for feeder replacements during planned outages. As may be expected, performing single feeder replacement in the congested working environment of an operational CANDU reactor face involves overcoming many challenges with respect to access to feeders, available clearances for tooling, and tooling operation and performance. This paper describes some of the challenges encountered during single feeder replacements and actions being taken by AECL and B and W to promote continuous improvement of feeder replacement tooling and processes and ensure well-executed outages. (author)

  2. Efficient Generation and Editing of Feeder-free IPSCs from Human Pancreatic Cells Using the CRISPR-Cas9 System.

    Science.gov (United States)

    Nandal, Anjali; Mallon, Barbara; Telugu, Bhanu P

    2017-11-08

    Embryonic and induced pluripotent stem cells can self-renew and differentiate into multiple cell types of the body. The pluripotent cells are thus coveted for research in regenerative medicine and are currently in clinical trials for eye diseases, diabetes, heart diseases, and other disorders. The potential to differentiate into specialized cell types coupled with the recent advances in genome editing technologies including the CRISPR/Cas system have provided additional opportunities for tailoring the genome of iPSC for varied applications including disease modeling, gene therapy, and biasing pathways of differentiation, to name a few. Among the available editing technologies, the CRISPR/Cas9 from Streptococcus pyogenes has emerged as a tool of choice for site-specific editing of the eukaryotic genome. The CRISPRs are easily accessible, inexpensive, and highly efficient in engineering targeted edits. The system requires a Cas9 nuclease and a guide sequence (20-mer) specific to the genomic target abutting a 3-nucleotide "NGG" protospacer-adjacent-motif (PAM) for targeting Cas9 to the desired genomic locus, alongside a universal Cas9 binding tracer RNA (together called single guide RNA or sgRNA). Here we present a step-by-step protocol for efficient generation of feeder-independent and footprint-free iPSC and describe methodologies for genome editing of iPSC using the Cas9 ribonucleoprotein (RNP) complexes. The genome editing protocol is effective and can be easily multiplexed by pre-complexing sgRNAs for more than one target with the Cas9 protein and simultaneously delivering into the cells. Finally, we describe a simplified approach for identification and characterization of iPSCs with desired edits. Taken together, the outlined strategies are expected to streamline generation and editing of iPSC for manifold applications.

  3. The influence of interleukin-2, feeder cells, and timing of irradiation on the radiosensitivity of human T lymphocytes assessed by the colony-forming assay

    International Nuclear Information System (INIS)

    Gerber, M.; Guichard, M.; Pioch, Y.; Dubois, J.B.

    1989-01-01

    The radiosensitivity of human lymphocytes was investigated by the method of colony formation in the absence of interleukin-2 (IL2) and feeder cells, both of which enhance growth of T-cell colonies. The shape of the survival curve and the radiosensitivity was shown to depend upon the ability of lymphocytes to produce IL2: the survival curve for lymphocytes that were the most competent producers of IL2 is the closest to linearity; the lymphocytes that were poor producers show biphasic survival curves. The radiosensitivity of the lymphocytes from the first group is less than that of the latter, when the comparison is based on the first part of the biphasic survival curve. This is more easily seen when cultures are irradiated 24 h after stimulation by phytohemagglutinin (the time of the peak IL2 production) than when cultures are irradiated 2 h before stimulation. This study demonstrates that growth conditions influence the response of lymphocytes to irradiation and that optimal growth conditions result in a linear survival curve

  4. Colour preferences of UK garden birds at supplementary seed feeders.

    Directory of Open Access Journals (Sweden)

    Luke Rothery

    Full Text Available Supplementary feeding of garden birds generally has benefits for both bird populations and human wellbeing. Birds have excellent colour vision, and show preferences for food items of particular colours, but research into colour preferences associated with artificial feeders is limited to hummingbirds. Here, we investigated the colour preferences of common UK garden birds foraging at seed-dispensing artificial feeders containing identical food. We presented birds simultaneously with an array of eight differently coloured feeders, and recorded the number of visits made to each colour over 370 30-minute observation periods in the winter of 2014/15. In addition, we surveyed visitors to a garden centre and science festival to determine the colour preferences of likely purchasers of seed feeders. Our results suggest that silver and green feeders were visited by higher numbers of individuals of several common garden bird species, while red and yellow feeders received fewer visits. In contrast, people preferred red, yellow, blue and green feeders. We suggest that green feeders may be simultaneously marketable and attractive to foraging birds.

  5. Development of dry coal feeders

    Science.gov (United States)

    Bonin, J. H.; Cantey, D. E.; Daniel, A. D., Jr.; Meyer, J. W.

    1977-01-01

    Design and fabrication of equipment of feed coal into pressurized environments were investigated. Concepts were selected based on feeder system performance and economic projections. These systems include: two approaches using rotating components, a gas or steam driven ejector, and a modified standpipe feeder concept. Results of development testing of critical components, design procedures, and performance prediction techniques are reviewed.

  6. YKL-40 is differentially expressed in human embryonic stem cells and in cell progeny of the three germ layers

    DEFF Research Database (Denmark)

    Brøchner, Christian B; Johansen, Julia S; Larsen, Lars A

    2012-01-01

    oxygen tension, in culture medium with or without basic fibroblast growth factor, and on feeder layers comprising mouse embryonic fibroblasts or human foreskin fibroblasts to evaluate whether hESCs and their progeny produced YKL-40 and to characterize YKL-40 expression during differentiation. Secreted......The secreted glycoprotein YKL-40 participates in cell differentiation, inflammation, and cancer progression. High YKL-40 expression is reported during early human development, but its functions are unknown. Six human embryonic stem cell (hESC) lines were cultured in an atmosphere of low or high...... YKL-40 protein and YKL-40 mRNA expression were measured by enzyme-linked immunosorbent assay (ELISA) and quantitative RT-PCR. Serial-sectioned colonies were stained for YKL-40 protein and for pluripotent hESC (OCT4, NANOG) and germ layer (HNF-3ß, PDX1, CD34, p63, nestin, PAX6) markers. Double...

  7. Rapid fabricating technique for multi-layered human hepatic cell sheets by forceful contraction of the fibroblast monolayer.

    Directory of Open Access Journals (Sweden)

    Yusuke Sakai

    Full Text Available Cell sheet engineering is attracting attention from investigators in various fields, from basic research scientists to clinicians focused on regenerative medicine. However, hepatocytes have a limited proliferation potential in vitro, and it generally takes a several days to form a sheet morphology and multi-layered sheets. We herein report our rapid and efficient technique for generating multi-layered human hepatic cell (HepaRG® cell sheets using pre-cultured fibroblast monolayers derived from human skin (TIG-118 cells as a feeder layer on a temperature-responsive culture dish. Multi-layered TIG-118/HepaRG cell sheets with a thick morphology were harvested on day 4 of culturing HepaRG cells by forceful contraction of the TIG-118 cells, and the resulting sheet could be easily handled. In addition, the human albumin and alpha 1-antitrypsin synthesis activities of TIG-118/HepaRG cells were approximately 1.2 and 1.3 times higher than those of HepaRG cells, respectively. Therefore, this technique is considered to be a promising modality for rapidly fabricating multi-layered human hepatocyte sheets from cells with limited proliferation potential, and the engineered cell sheet could be used for cell transplantation with highly specific functions.

  8. An evaluation of the choice of feeder cell growth arrest for the production of cultured epidermis.

    Science.gov (United States)

    Chugh, Rishi Man; Chaturvedi, Madhusudan; Yerneni, Lakshmana Kumar

    2015-12-01

    Growth arrested 3T3 cells have been used as feeder cells in human epidermal keratinocyte cultures to produce cultured epidermal autografts for the treatment of burns. The feeder cells were ideally growth-arrested by gamma-irradiation. Alternatively, growth arrest by mitomycin C treatment is a cost effective option. We compared the functional efficacy of these two approaches in keratinocyte cultures by colony forming efficiency, the net growth area of colonies, BrdU labeling and histological features of cultured epidermal sheets. The growth area estimation involved a semi-automated digital technique using the Adobe Photoshop and comprised of isolation and enumeration of red pixels in Rhodamine B-stained keratinocyte colonies. A further refinement of the technique led to the identification of critical steps to increasing the degree of accuracy and enabling its application as an extension of colony formation assay. The results on feeder cell functionality revealed that the gamma irradiated feeders influenced significantly higher colony forming efficiency and larger growth area than the mitomycin C treated feeders. The BrdU labeling study indicated significant stimulation of the overall keratinocyte proliferation by the gamma irradiated feeders. The cultured epidermal sheets produced by gamma feeders were relatively thicker than those produced by mitomycin C feeders. We discussed the clinical utility of mitomycin C feeders from the viewpoint of cost-effective burn care in developing countries. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

  9. Leaky feeder: the communication backbone

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-01-01

    The need to communicate with all areas of the underground operation in monitoring the movement of men, materials and vehicles, as well as the optimum performance of conveyor systems, has been effectively met with the installation of a Flexcom leaky feeder cable network at a coliery in Mpumalanga. Installed by the South African subsidiary of Mine Radio Systems (MRS), based in Canada, Flexcom is an RF communications highway for underground mines. The system can provide up to 32 voice/data control channels and up to 16 video channels, all operating simultaneously. The system uses a series of bi-directional amplifiers (or signal boosters) spaced at 350 m intervals along the leaky feeder cable, with branching units and termination units added as required. Communication is possible within 50 m of the leaky feeder cable. MRS has 11 conveyors monitored via the SCADA program at the mine and the system produces reports as required which are accessible via cellphone from anywhere in the world. The wireless monitoring of miners and equipment contributes to mine safety. 3 figs.

  10. in meat production III. Feeder - breeder dimorphism

    African Journals Online (AJOL)

    Feeder- breeder dimorphism is advantageous when large offspring for slaughter is obtained from small breeding animals. The effect of feeder- breeder dimorphism on herd efficiency is evaluated for terminal crossbreeding and growth modification by biotechnological or dietary means. Selection criteria for breeds or lines in ...

  11. YKL-40 is differentially expressed in human embryonic stem cells and in cell progeny of the three germ layers.

    Science.gov (United States)

    Brøchner, Christian B; Johansen, Julia S; Larsen, Lars A; Bak, Mads; Mikkelsen, Hanne B; Byskov, Anne Grete; Andersen, Claus Yding; Møllgård, Kjeld

    2012-03-01

    The secreted glycoprotein YKL-40 participates in cell differentiation, inflammation, and cancer progression. High YKL-40 expression is reported during early human development, but its functions are unknown. Six human embryonic stem cell (hESC) lines were cultured in an atmosphere of low or high oxygen tension, in culture medium with or without basic fibroblast growth factor, and on feeder layers comprising mouse embryonic fibroblasts or human foreskin fibroblasts to evaluate whether hESCs and their progeny produced YKL-40 and to characterize YKL-40 expression during differentiation. Secreted YKL-40 protein and YKL-40 mRNA expression were measured by enzyme-linked immunosorbent assay (ELISA) and quantitative RT-PCR. Serial-sectioned colonies were stained for YKL-40 protein and for pluripotent hESC (OCT4, NANOG) and germ layer (HNF-3β, PDX1, CD34, p63, nestin, PAX6) markers. Double-labeling showed YKL-40 expression in OCT4-positive hESCs, PAX6-positive neuroectodermal cells, and HNF-3β-positive endodermal cells. The differentiating progeny showed strong YKL-40 expression. Abrupt transition between YKL-40 and OCT4-positive hESCs and YKL-40-positive ecto- and neuroectodermal lineages was observed within the same epithelial-like layer. YKL-40-positive cells within deeper layers lacked contact with OCT4-positive cells. YKL-40 may be important in initial cell differentiation from hESCs toward ectoderm and neuroectoderm, with retained epithelial morphology, whereas later differentiation into endoderm and mesoderm involves a transition into the deeper layers of the colony.

  12. An RFID Based Smart Feeder for Hummingbirds.

    Science.gov (United States)

    Ibarra, Vicente; Araya-Salas, Marcelo; Tang, Yu-ping; Park, Charlie; Hyde, Anthony; Wright, Timothy F; Tang, Wei

    2015-12-16

    We present an interdisciplinary effort to record feeding behaviors and control the diet of a hummingbird species (Phaethornis longirostris, the long-billed hermit or LBH) by developing a Radio Frequency Identification (RFID) based smart feeder. The system contains an RFID reader, a microcontroller, and a servo-controlled hummingbird feeder opener; the system is presented as a tool for studying the cognitive ability of the LBH species. When equipped with glass capsule RFID tags (which are mounted on the hummingbird), the smart feeder can provide specific diets for predetermined sets of hummingbirds at the discretion of biologists. This is done by reading the unique RFID tag on the hummingbirds and comparing the ID number with the pre-programmed ID numbers stored in the smart feeder. The smart feeder records the time and ID of each hummingbird visit. The system data is stored in a readily available SD card and is powered by two 9 V batteries. The detection range of the system is approximately 9-11 cm. Using this system, biologists can assign the wild hummingbirds to different experimental groups and monitor their diets to determine if they develop a preference to any of the available nectars. During field testing, the smart feeder system has demonstrated consistent detection (when compared to detections observed by video-recordings) of RFID tags on hummingbirds and provides pre-designed nectars varying water and sugar concentrations to target individuals. The smart feeder can be applied to other biological and environmental studies in the future.

  13. Hidden layers of human small RNAs

    DEFF Research Database (Denmark)

    Kawaji, Hideya; Nakamura, Mari; Takahashi, Yukari

    2008-01-01

    small RNA have focused on miRNA and/or siRNA rather than on the exploration of additional classes of RNAs. RESULTS: Here, we explored human small RNAs by unbiased sequencing of RNAs with sizes of 19-40 nt. We provide substantial evidences for the existence of independent classes of small RNAs. Our data......BACKGROUND: Small RNA attracts increasing interest based on the discovery of RNA silencing and the rapid progress of our understanding of these phenomena. Although recent studies suggest the possible existence of yet undiscovered types of small RNAs in higher organisms, many studies to profile...... shows that well-characterized non-coding RNA, such as tRNA, snoRNA, and snRNA are cleaved at sites specific to the class of ncRNA. In particular, tRNA cleavage is regulated depending on tRNA type and tissue expression. We also found small RNAs mapped to genomic regions that are transcribed in both...

  14. A study of inter linkage effects on Candu feeder piping

    International Nuclear Information System (INIS)

    Li, M.; Aggarwal, M.L.; Meysner, A.

    2005-01-01

    A CANDU (Canadian Deuterium Uranium) reactor core consists of a large number of fuel channels where heat is generated. Two feeder pipes are connected to each fuel channel to transport D 2 O coolant into and out of the reactor core. The feeder piping is designed to the requirements of Class 1 piping of Section III NB of the ASME Boiler and Pressure Vessel and CSA Codes. Feeder piping stress analysis is being performed to demonstrate the code compliance check and the fitness for service of feeders. In the past, stress analyses were conducted for each individual feeder without including interaction effects among connected feeders. Interaction effects occur as a result of linkages that exist between feeders to prevent fretting and impacting damage during normal, abnormal and accident conditions. In this paper, a 'combined' approach is adopted to include all feeders connected by inter linkages into one feeder piping model. MSC/NASTRAN finite element software was used in the stress simulation, which contains up to 127 feeder pipes. The ASME Class 1 piping analysis was conducted to investigate the effects of the linkages between feeders. Both seismic time history and broadened response spectra methods were used in the seismic stress calculation. The results show that the effect of linkages is significant in dynamic stresses for all feeder configurations, as well as in static stresses for certain feeder configurations. The single feeder analysis could either underestimate or overestimate feeder stresses depending on the pipe geometry and bend wall thickness. (authors)

  15. An RFID Based Smart Feeder for Hummingbirds

    Directory of Open Access Journals (Sweden)

    Vicente Ibarra

    2015-12-01

    Full Text Available We present an interdisciplinary effort to record feeding behaviors and control the diet of a hummingbird species (Phaethornis longirostris, the long-billed hermit or LBH by developing a Radio Frequency Identification (RFID based smart feeder. The system contains an RFID reader, a microcontroller, and a servo-controlled hummingbird feeder opener; the system is presented as a tool for studying the cognitive ability of the LBH species. When equipped with glass capsule RFID tags (which are mounted on the hummingbird, the smart feeder can provide specific diets for predetermined sets of hummingbirds at the discretion of biologists. This is done by reading the unique RFID tag on the hummingbirds and comparing the ID number with the pre-programmed ID numbers stored in the smart feeder. The smart feeder records the time and ID of each hummingbird visit. The system data is stored in a readily available SD card and is powered by two 9 V batteries. The detection range of the system is approximately 9–11 cm. Using this system, biologists can assign the wild hummingbirds to different experimental groups and monitor their diets to determine if they develop a preference to any of the available nectars. During field testing, the smart feeder system has demonstrated consistent detection (when compared to detections observed by video-recordings of RFID tags on hummingbirds and provides pre-designed nectars varying water and sugar concentrations to target individuals. The smart feeder can be applied to other biological and environmental studies in the future.

  16. Economic feeder for recharging and ``topping off''

    Science.gov (United States)

    Fickett, Bryan; Mihalik, G.

    2000-04-01

    Increasing the size of the melt charge significantly increases yield and reduces costs. Siemens Solar Industries is optimizing a method to charge additional material after meltdown (top-off) using an external feeder system. A prototype feeder system was fabricated consisting of a hopper and feed delivery system. The low-cost feeder is designed for simple operation and maintenance. The system is capable of introducing up to 60 kg of granular silicon while under vacuum. An isolation valve permits refilling of the hopper while maintaining vacuum in the growth furnace. Using the feeder system in conjunction with Siemens Solar Industries' energy efficient hot zone dramatically reduces power and argon consumption. Throughput is also improved as faster pull speeds can be attained. The increased pull speeds have an even greater impact when the charge size is increased. Further cost reduction can be achieved by refilling the crucible after crystal growth and pulling a second ingot run. Siemens Solar Industries is presently testing the feeder in production.

  17. Advances in technologies for feeder pipe inspections

    Energy Technology Data Exchange (ETDEWEB)

    Ten Grotenhuis, R.; Verma, Y.; Hitchcox, T.; Sakuta, A. [Ontario Power Generation, Inspection and Maintenance Div., Toronto, Ontario (Canada)

    2014-07-15

    The successful development of the Matrix Inspection Technique (MIT) for feeder weld area applications has been followed up with a project to leverage the technology to address other aspects of feeder inspection. The goal of the project is to adapt the technology to provide full circumferential inspection of feeder pipes for FAC thinning and, potentially, for axial cracking. The project necessitated evolving a new generation of high speed, high element count data acquisition instruments. It also required the development of custom inspection arrays, innovative approaches to sealing the water column, use of inertial motion sensors to synthesize encoder inputs, real-time visual feedback for the operator, and enhanced automated analysis software capable of plotting the inspected configuration in 3D. The individual components of the system are currently being integrated into a whole. The results obtained to date demonstrate the approach to be fundamentally sound. (author)

  18. Vertical-Screw-Auger Conveyer Feeder

    Science.gov (United States)

    Walton, Otis (Inventor); Vollmer, Hubert J. (Inventor)

    2016-01-01

    A conical feeder is attached to a vertically conveying screw auger. The feeder is equipped with scoops and rotated from the surface to force-feed regolith the auger. Additional scoops are possible by adding a cylindrical section above the conical funnel section. Such then allows the unit to collect material from swaths larger in diameter than the enclosing casing pipe of the screw auger. A third element includes a flexible screw auger. All three can be used in combination in microgravity and zero atmosphere environments to drill and recover a wide area of subsurface regolith and entrained volatiles through a single access point on the surface.

  19. Counseling in the Elementary Feeder Schools.

    Science.gov (United States)

    Dunham, Virginia

    This brief paper presents the concept of transition counseling between a junior high school and its feeder school(s), designed to make the change from elementary into junior high less traumatic. Aside from routine sixth grade counseling, the counselors expanded their base of counseling to include all types of problems as well as all grade levels.…

  20. The development and manufacture of size for size feeder pipe for feeder replacement

    International Nuclear Information System (INIS)

    Legate, G.; Schreiter, D.; Townley, N.

    2008-01-01

    The recently recognised problem of feeder pipe thinning created a unique sourcing problem. Operators require relatively small quantities of nuclear class 1 seamless feeder pipe for such replacement which prior to the introduction of this product in 2006 was not available. It was desired that the pipe be produced at the exact size of the pipe currently in use at the specific reactor site (feeder pipe size varies from site to site). Secondly the pipe had to be made in conformance to the original code year of issue and to conform to the intent of the original material specifications. Finally a supply strategy had to be implemented allowing for timely manufacture of replacement piping. This presentation will report upon how replacement size for size feeder tube was developed and is currently manufactured at Nu-Tech Precision Metals. The paper will also detail the current supply strategy to ensure timely manufacture of the product.

  1. Expectations of Cattle Feeding Investors in Feeder Cattle Placements

    OpenAIRE

    Kastens, Terry L.; Schroeder, Ted C.

    1993-01-01

    Cattle feeders appear irrational when they place cattle on feed when projected profits are negative. Long futures positions appear to offer superior returns to cattle feeding investment. Cattle feeder behavior suggests that they believe a downward bias in live cattle futures persists and that cattle feeders use different information than the live cattle futures market price when making placement decisions. This paper examines feeder cattle placement determinants and compares performance of ex...

  2. Optimization of Human NK Cell Manufacturing: Fully Automated Separation, Improved Ex Vivo Expansion Using IL-21 with Autologous Feeder Cells, and Generation of Anti-CD123-CAR-Expressing Effector Cells.

    Science.gov (United States)

    Klöß, Stephan; Oberschmidt, Olaf; Morgan, Michael; Dahlke, Julia; Arseniev, Lubomir; Huppert, Volker; Granzin, Markus; Gardlowski, Tanja; Matthies, Nadine; Soltenborn, Stephanie; Schambach, Axel; Koehl, Ulrike

    2017-10-01

    The administration of ex vivo expanded natural killer (NK) cells as potential antitumor effector cells appears to be suitable for effector cell-based immunotherapies in high-risk cancer patients. However, good manufacturing practice (GMP)-compliant manufacturing of clinical-grade NK cells at sufficiently high numbers represents a great challenge. Therefore, previous expansion protocols for those effector cells were improved and optimized by using newly developed culture medium, interleukin (IL)-21, and autologous feeder cells (FCs). Separation of primary human NK cells (CD56 + CD3 - ) was carried out with the CliniMACS Prodigy ® in a single process, starting with approximately 1.2 × 10 9 leukocytes collected by small-scale lymphapheresis or from buffy coats. Enriched NK cells were adjusted to starting cell concentrations within approximately 1 × 10 6 effector cells/mL and cultured in comparative expansion experiments for 14 days with IL-2 (1,000 IU/mL) in different GMP-compliant media (X-VIVO ™ 10, CellGro ® , TexMACS ™ , and NK MACS ® ). After medium optimization, beneficial effects for functionality and phenotype were investigated at the beginning of cell expansion with irradiated (25 Gy) autologous FCs at a ratio of 20:1 (feeder: NK) in the presence or absence of IL-21 (100 ng/mL). Additionally, expanded NK cells were gene modified to express chimeric antigen receptors (CARs) against CD123, a common marker for acute myeloid leukemia (AML). Cytotoxicity, degranulation, and cytokine release of transduced NK cells were determined against KG1a cells in flow cytometric analysis and fluorescent imaging. The Prodigy manufacturing process revealed high target cell viabilities (median 95.4%), adequate NK cell recovery (median 60.4%), and purity of 95.4% in regard to CD56 + CD3 - target cells. The process in its early phase of development led to a median T-cell depletion of log 3.5 after CD3 depletion and log 3.6 after the whole process, including CD3

  3. A bend thickness sensitivity study of Candu feeder piping

    International Nuclear Information System (INIS)

    Li, M.; Aggarwal, M.L.; Meysner, A.; Micelotta, C.

    2005-01-01

    In CANDU reactors, feeder bends close to the connection at the fuel channel may be subjected to the highest Flow Accelerated Corrosion (FAC) and stresses. Feeder pipe stress analysis is crucial in the life extension of aging CANDU plants. Typical feeder pipes are interconnected by upper link plates and spacers. It is well known that the stresses at the bends are sensitive to the local bend thicknesses. It is also known from the authors' study (Li and et al, 2005) that feeder inter linkage effect is significant and cannot be ignored. The field measurement of feeder bend thickness is difficult and may be subjected to uncertainty in accuracy. Hence, it is desirable to know how the stress on a subject feeder could be affected by the bend thickness variation of the neighboring feeders. This effect cannot be evaluated by the traditional 'single' feeder model approach. In this paper, the 'row' and 'combined' models developed in the previous study (Li and et al, 2005), which include the feeder interactions, are used to investigate the sensitivity of bend thickness. A series of random thickness bounded by maximum and minimum measured values were applied to feeders in the model. The results show that an individual feeder is not sensitive to the bend thickness variation of the remaining feeders in the model, but depends primarily on its own bend thickness. The highest stress at a feeder always occurs when the feeder has the smallest possible bend thickness. A minimum acceptable bend thickness for individual feeders can be computed by an iterative computing process. The dependency of field thickness measurement and the amount of required analysis work can be greatly reduced. (authors)

  4. Pressurized feeder for biofuels; Paineistettu syoetin biopolttoaineille

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, R; Makkonen, P [Foster Wheeler Energia Oy, Karhula (Finland). Karhula R and D Center

    1996-12-31

    A new type of pressurized piston feeder has been tested for further development of the IGCC concept. The project is funded by the Finnish Ministry of Trade and Industry. The objective has been to develop a substitute for lock-hopper systems, which are commercial, but far too expensive from an operational point of view, due to high inert gas consumption for pressurization. The new feeder system, which is of dual piston type, uses little inert gas, because the pressurization sequence is performed partially by the piston movement. The project comprised further development of the concept, mechanical testing under atmospheric and pressurized conditions and testing with wood chips, peat and coal at elevated pressures. The main concern has been the wear of seals and gaskets during long term operation and for this reason over 600 hours of testing has been carried out. The tests were carried out between May 1994 and January 1995 with wood chips, peat and coal mainly at 17 bar(a) pressure. During the operation, the system was fine-tuned, and generally, the testing was successful. At the early stage of the tests, the ring seal design was modified and several alternative seal constructions were tested. During the tests, the seal was developed further and improved. The present ring seal design has been proven reliable and it meets the commercial requirements. After the tests, the feeder system was inspected thoroughly and found to be in good condition. A commercially available concept of the feeder has been developed on the basis of the knowledge obtained during the test runs

  5. Pressurized feeder for biofuels; Paineistettu syoetin biopolttoaineille

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, R.; Makkonen, P. [Foster Wheeler Energia Oy, Karhula (Finland). Karhula R and D Center

    1995-12-31

    A new type of pressurized piston feeder has been tested for further development of the IGCC concept. The project is funded by the Finnish Ministry of Trade and Industry. The objective has been to develop a substitute for lock-hopper systems, which are commercial, but far too expensive from an operational point of view, due to high inert gas consumption for pressurization. The new feeder system, which is of dual piston type, uses little inert gas, because the pressurization sequence is performed partially by the piston movement. The project comprised further development of the concept, mechanical testing under atmospheric and pressurized conditions and testing with wood chips, peat and coal at elevated pressures. The main concern has been the wear of seals and gaskets during long term operation and for this reason over 600 hours of testing has been carried out. The tests were carried out between May 1994 and January 1995 with wood chips, peat and coal mainly at 17 bar(a) pressure. During the operation, the system was fine-tuned, and generally, the testing was successful. At the early stage of the tests, the ring seal design was modified and several alternative seal constructions were tested. During the tests, the seal was developed further and improved. The present ring seal design has been proven reliable and it meets the commercial requirements. After the tests, the feeder system was inspected thoroughly and found to be in good condition. A commercially available concept of the feeder has been developed on the basis of the knowledge obtained during the test runs

  6. Improvement of automatic fish feeder machine design

    Science.gov (United States)

    Chui Wei, How; Salleh, S. M.; Ezree, Abdullah Mohd; Zaman, I.; Hatta, M. H.; Zain, B. A. Md; Mahzan, S.; Rahman, M. N. A.; Mahmud, W. A. W.

    2017-10-01

    Nation Plan of action for management of fishing is target to achieve an efficient, equitable and transparent management of fishing capacity in marine capture fisheries by 2018. However, several factors influence the fishery production and efficiency of marine system such as automatic fish feeder machine could be taken in consideration. Two latest fish feeder machines have been chosen as the reference for this study. Based on the observation, it has found that the both machine was made with heavy structure, low water and temperature resistance materials. This research’s objective is to develop the automatic feeder machine to increase the efficiency of fish feeding. The experiment has conducted to testing the new design of machine. The new machine with maximum storage of 5 kg and functioning with two DC motors. This machine able to distribute 500 grams of pellets within 90 seconds and longest distance of 4.7 meter. The higher speed could reduce time needed and increase the distance as well. The minimum speed range for both motor is 110 and 120 with same full speed range of 255.

  7. Polymeric membranes modulate human keratinocyte differentiation in specific epidermal layers.

    Science.gov (United States)

    Salerno, Simona; Morelli, Sabrina; Giordano, Francesca; Gordano, Amalia; Bartolo, Loredana De

    2016-10-01

    In vitro models of human bioengineered skin substitutes are an alternative to animal experimentation for testing the effects and toxicity of drugs, cosmetics and pollutants. For the first time specific and distinct human epidermal strata were engineered by using membranes and keratinocytes. To this purpose, biodegradable membranes of chitosan (CHT), polycaprolactone (PCL) and a polymeric blend of CHT-PCL were prepared by phase-inversion technique and characterized in order to evaluate their morphological, physico-chemical and mechanical properties. The capability of membranes to modulate keratinocyte differentiation inducing specific interactions in epidermal membrane systems was investigated. The overall results demonstrated that the membrane properties strongly influence the cell morpho-functional behaviour of human keratinocytes, modulating their terminal differentiation, with the creation of specific epidermal strata or a fully proliferative epidermal multilayer system. In particular, human keratinocytes adhered on CHT and CHT-PCL membranes, forming the structure of the epidermal top layers, such as the corneum and granulosum strata, characterized by withdrawal or reduction from the cell cycle and cell proliferation. On the PCL membrane, keratinocytes developed an epidermal basal lamina, with high proliferating cells that stratified and migrated over time to form a complete differentiating epidermal multilayer system. Copyright © 2016 Elsevier B.V. All rights reserved.

  8. Feeder density enhances house finch disease transmission in experimental epidemics.

    Science.gov (United States)

    Moyers, Sahnzi C; Adelman, James S; Farine, Damien R; Thomason, Courtney A; Hawley, Dana M

    2018-05-05

    Anthropogenic food provisioning of wildlife can alter the frequency of contacts among hosts and between hosts and environmental sources of pathogens. Despite the popularity of garden bird feeding, few studies have addressed how feeders influence host contact rates and disease dynamics. We experimentally manipulated feeder density in replicate aviaries containing captive, pathogen-naive, groups of house finches ( Haemorhous mexicanus ) and continuously tracked behaviours at feeders using radio-frequency identification devices. We then inoculated one bird per group with Mycoplasma gallisepticum (Mg), a common bacterial pathogen for which feeders are fomites of transmission, and assessed effects of feeder density on house finch behaviour and pathogen transmission. We found that pathogen transmission was significantly higher in groups with the highest density of bird feeders, despite a significantly lower rate of intraspecific aggressive interactions relative to the low feeder density groups. Conversely, among naive group members that never showed signs of disease, we saw significantly higher concentrations of Mg-specific antibodies in low feeder density groups, suggesting that birds in low feeder density treatments had exposure to subclinical doses of Mg. We discuss ways in which the density of garden bird feeders could play an important role in mediating the intensity of Mg epidemics.This article is part of the theme issue 'Anthropogenic resource subsidies and host-parasite dynamics in wildlife'. © 2018 The Author(s).

  9. Impact of flow accelerated corrosion (FAC) on feeder refurbishment planning

    International Nuclear Information System (INIS)

    Jyrkama, M.; Pandey, M.

    2010-01-01

    Feeder wall thinning due to flow accelerated corrosion (FAC) may result in a large number of feeder replacements in the future. In this study, the process of FAC is modelled using a probabilistic approach and used to predict the expected number of degraded feeders and their replacements in the future. Because of the high cost associated with feeder replacements, it may be optimal to replace the entire feeder population during a single refurbishment outage when the unit cost of replacement is likely to be less. The results of this study demonstrate, however, that the unit cost of feeder replacement must be sufficiently lower than the standard replacement cost and the refurbishment performed at an optimal time to realize the economic benefits associated with the refurbishment. (author)

  10. A HYBRID APPROACH FOR RURAL FEEDER DESIGN

    Directory of Open Access Journals (Sweden)

    DAMANJEET KAUR

    2012-08-01

    Full Text Available In this paper, a population based approach for conductor size selection in rural radial distribution system is presented. The proposed hybrid approach implies a particle swarm optimization (PSO approach in combination with mutant property of differential evolution (DE for conductor size selection in radial distribution system. The conductor size for each feeder segment is selected such that the total cost of capital investment and capitalized cost of energy losses is minimized while constraints of voltage at each node and current carrying capacity of conductor is within the limits. The applicability and effectiveness of the proposed method is demonstrated with the help of 32-node test system.

  11. Risk-informed prediction of feeder end of life

    International Nuclear Information System (INIS)

    Jyrkama, M.; Pandey, M.

    2011-01-01

    The operating life of feeder piping is negatively impacted by flow accelerated corrosion (FAC). In this study, an assessment of a large set of inspection data reveals that FAC in feeders is a relatively stationary process, with variability only at the local scale. Given the added uncertainty from inspection coverage, a new method for estimating the thinning rate and feeder EOL is developed using a probabilistic approach. The results of the study illustrate the benefits of the methodology in supporting risk-informed decision making at the station by quantifying the present and incremental risk in the feeder system over time. (author)

  12. Determination of representative CANDU feeder dimensions for engineering simulator

    International Nuclear Information System (INIS)

    Cho, S.; Muzumdar, A.

    1996-01-01

    This paper describes a logic for selection of representative channel groups and a methodology for determination of representative CANDU feeder dimensions and the pressure drops between inlet/outlet header and fuel channel in the primary loop. A code, MEDOC, was developed based on this logic and methodology and helps perform a calculation of representative feeder dimensions for a selected channel group on the basis of feeder geometry data (fluid volume, mass flow rate, loss factor) and given property data (pressure, quality, density) at inlet/outlet header. The representative feeder dimensions calculated based on this methodology will be useful for the engineering simulator for the CANDU type reactor. (author)

  13. Risk-informed prediction of feeder end of life

    Energy Technology Data Exchange (ETDEWEB)

    Jyrkama, M.; Pandey, M. [Univ. of Waterloo, Ontario (Canada)

    2011-07-01

    The operating life of feeder piping is negatively impacted by flow accelerated corrosion (FAC). In this study, an assessment of a large set of inspection data reveals that FAC in feeders is a relatively stationary process, with variability only at the local scale. Given the added uncertainty from inspection coverage, a new method for estimating the thinning rate and feeder EOL is developed using a probabilistic approach. The results of the study illustrate the benefits of the methodology in supporting risk-informed decision making at the station by quantifying the present and incremental risk in the feeder system over time. (author)

  14. The Use of Filter-feeders to Manage Disease in a Changing World.

    Science.gov (United States)

    Burge, Colleen A; Closek, Collin J; Friedman, Carolyn S; Groner, Maya L; Jenkins, Cody M; Shore-Maggio, Amanda; Welsh, Jennifer E

    2016-10-01

    Rapid environmental change is linked to increases in aquatic disease heightening the need to develop strategies to manage disease. Filter-feeding species are effective biofilters and can naturally mitigate disease risk to humans and wildlife. We review the role of filter-feeders, with an emphasis on bivalves, in altering disease outcomes via augmentation and reduction. Filtration can reduce transmission by removing pathogens from the water column via degradation and release of pathogens in pseudofeces. In other cases, filtration can increase pathogen transmission and disease risk. The effect of filtration on pathogen transmission depends on the selectivity of the filter-feeder, the degree of infectivity by the pathogen, the mechanism(s) of pathogen transmission and the ability of the pathogen to resist degradation. For example, some bacteria and viruses can resist degradation and accumulate within a filter-feeder leading to disease transmission to humans and other wildlife upon ingestion. Since bivalves can concentrate microorganisms, they are also useful as sentinels for the presence of pathogenic microorganisms. While somewhat less studied, other invertebrates, including ascidians and sponges may also provide ecosystem services by altering pathogen transmission. In all scenarios, climate change may affect the potential for filter-feeders to mitigate disease risk. We conclude that an assessment including empirical data and modeling of system-wide impacts should be conducted before selection of filter-feeders to mitigate disease. Such studies should consider physiology of the host and microbe and risk factors for negative impacts including augmentation of other pathogens. © The Author 2016. Published by Oxford University Press on behalf of the Society for Integrative and Comparative Biology. All rights reserved. For permissions please email: journals.permissions@oup.com.

  15. 26 CFR 1.502-1 - Feeder organizations.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 7 2010-04-01 2010-04-01 true Feeder organizations. 1.502-1 Section 1.502-1...) INCOME TAXES (CONTINUED) Exempt Organizations § 1.502-1 Feeder organizations. (a) In the case of an organization operated for the primary purpose of carrying on a trade or business for profit, exemption is not...

  16. Development of ceramic-free antenna feeder

    International Nuclear Information System (INIS)

    Moriyama, S.; Kimura, H.; Fujii, T.; Saigusa, M.; Arai, H.

    1994-01-01

    We have proposed a ceramics-free antenna feeder line employing a ridged waveguide as a local support for IC antenna of next-generation tokamaks. One fourth mock-up model of the all metal waveguide designed for the ITER ICRF system is fabricated and electrical characteristics of the model including the coaxial line - waveguide converter are measured. Power reflection coefficient of the model including the coax-waveguide converter to the input coaxial line is estimated to be less than 15% below the cut-off frequency of 107 MHz and less than 3% above the cut-off frequency. It is found that this ceramics-free antenna support employing a ridged waveguide is quite available for IC antenna of next-generation tokamaks. (author)

  17. Vertical linear feeder to elliptical igneous saucer-shaped sills: evidences from structural observations, geochemistry and experimental modeling

    Science.gov (United States)

    Galerne, C. Y.; Galland, O.; Neumann, E. R.; Planke, S.

    2009-12-01

    The structural relationships between sills and their feeders are poorly documented because they are rarely observed in the field and difficult to image on seismic data. For instance, it is unclear whether sills are fed by pipes, dikes or other sills. Nevertheless, the geometrical relationships between sills and their feeders provide first-order constraints on magma emplacement mechanisms. Here, we investigate the structural and geochemical relationships between sills and potential feeder dikes in a remarkably well-preserved and exposed sill complex, the Golden Valley Sill Complex (GVSC), Karoo Basin, South Africa. The GVSC consists of five major saucer-shaped sills and six dikes. The Golden Valley sill itself is an elliptical saucer, with a N-S trend. A one meter thick dike (D4) crops out underneath the southern tip of the Golden Valley sill. The strike of this dike is parallel to the long axis of the Golden Valley sill. Detailed sampling and geochemical analyses of the GVSC show that each sill and dike exhibits a specific geochemical signature. The Golden Valley sill and its underlying dike D4 have identical signatures. Although there is no clear structural evidence, the consistent geometrical and geochemical relationships between the Golden Valley sill and the D4 dike suggest that this vertical linear structure is the feeder of the overlying saucer-shaped sill. In order to investigate the relationships between sills and feeders, we resorted to scaled laboratory experiments. The experiments consisted of a low-viscosity vegetable oil representing magma and a cohesive fine-grained silica flour representing brittle rocks. We placed a horizontal weak layer into the silica flour, just above the top of the inlet, to simulate strata. Such a weak layer controlled the formation of horizontal sill that subsequently turned into a transgressive sheet leading to the formation of a saucer geometry. We ran experiments with varying inlet shapes: 1) a point inlet representing a

  18. Layer-by-Layer Heparinization of the Cell Surface by Using Heparin-Binding Peptide Functionalized Human Serum Albumin.

    Science.gov (United States)

    Song, Guowei; Hu, Yaning; Liu, Yusheng; Jiang, Rui

    2018-05-20

    Layer-by-layer heparinization of therapeutic cells prior to transplantation is an effective way to inhibit the instant blood-mediated inflammatory reactions (IBMIRs), which are the major cause of early cell graft loss during post-transplantation. Here, a conjugate of heparin-binding peptide (HBP) and human serum albumin (HSA), HBP-HSA, was synthesized by using heterobifunctional crosslinker. After the first heparin layer was coated on human umbilical vein endothelial cells (HUVECs) by means of the HBP-polyethylene glycol-phospholipid conjugate, HBP-HSA and heparin were then applied to the cell surface sequentially to form multiple layers. The immobilization and retention of heparin were analyzed by confocal microscopy and flow cytometry, respectively, and the cytotoxity of HBP-HSA was further evaluated by cell viability assay. Results indicated that heparin was successfully introduced to the cell surface in a layer-by-layer way and retained for at least 24 h, while the cytotoxity of HBP-HSA was negligible at the working concentration. Accordingly, this conjugate provides a promising method for co-immobilization of heparin and HSA to the cell surface under physiological conditions with improved biocompatibility.

  19. Human factors in layers of defense in airport security

    NARCIS (Netherlands)

    Andriessen, H.; Van Gulijk, C.; Ale, B.J.M.

    2012-01-01

    Airport security systems are built up out of layers of defence based on the security-in-depth model (Talbot & Jakeman, 2008). The Transport Safety Authority (TSA) in the United States defined a staggering 20 layers of defence to control security risks. This means that not only security personnel is

  20. A Dynamic and Heuristic Phase Balancing Method for LV Feeders

    Directory of Open Access Journals (Sweden)

    Samad Taghipour Boroujeni

    2016-01-01

    Full Text Available Due to the single-phase loads and their stochastic behavior, the current in the distribution feeders is not balanced. In addition, the single-phase loads are located in different positions along the LV feeders. So the amount of the unbalanced load and its location affect the feeder losses. An unbalanced load causes the feeder losses and the voltage drop. Because of time-varying behavior of the single-phase loads, phase balancing is a dynamic and combinatorial problem. In this research, a heuristic and dynamic solution for the phase balancing of the LV feeders is proposed. In this method, it is supposed that the loads’ tie could be connected to all phases through a three-phase switch. The aim of the proposed method is to make the feeder conditions as balanced as possible. The amount and the location of single-phase loads are considered in the proposed phase balancing method. Since the proposed method needs no communication interface or no remote controller, it is inexpensive, simple, practical, and robust. Applying this method provides a distributed and dynamic phase balancing control. In addition, the feasibility of reducing the used switches is investigated. The ability of the proposed method in the phase balancing of the LV feeders is approved by carrying out some simulations.

  1. A Decentralized Storage Strategy for Residential Feeders with Photovoltaics

    DEFF Research Database (Denmark)

    Marra, Francesco; Yang, Guangya; Træholt, Chresten

    2014-01-01

    . The power sizing of the ESSs is performed with linear programming (LP) method, based on voltage sensitivity analysis. A Belgian residential LV feeder with private PV systems is used as a case study to demonstrate the effectiveness of the proposed strategy. Quantification of the required energy levels...... domestic energy storage systems (ESS). The traditional way of operating a domestic ESS to increase the local consumption rate does not take into account the need of voltage support in a feeder; the proposed storage concept improves the traditional one, by mitigating voltage rise due to PV in the feeder...

  2. Automation Selection and Sequencing of Traps for Vibratory Feeders

    DEFF Research Database (Denmark)

    Mathiesen, Simon; Ellekilde, Lars-Peter

    2017-01-01

    Vibratory parts feeders with mechanical orienting devices are used extensively in the assembly automation industry. Even so, the design process is based on trial-and-error approaches and is largely manual. In this paper, a methodology is presented for automatic design of this type of feeder....... The approach uses dynamic simulation for generating the necessary data for configuring a feeder with a sequence of mechanical orienting devices called traps, with the goal of reorienting all parts from a random to fixed orientation. Then, a fast algorithm for facilitating this configuration task automatically...

  3. Damping considerations in CANDU feeder pipe design and analysis

    International Nuclear Information System (INIS)

    Usmani, S.A.; Saleem, M.A.; So, G.

    1990-01-01

    Recent developments in pipe damping indicate a trend towards more realistic and less conservative values, which result in less rigid and safer pipe designs. The CANDU-PHW (Canada deuterium uranium, pressurized heavy water) reactor feeder pipe designs have applied similar approaches which permit seismic qualifications without overly restraining these compact arrays of pipes to cater for the large creep and thermal anchor movement. This paper reviews the feeder design aspects, especially pertaining to the design provisions, experimental verification and analytical modelling for seismic qualification in the light of recent pipe dynamic developments. Using illustrative examples, comparison of seismic analysis results is provided for the ASME Code Case N-411 dampings, and those traditionally used in the feeder seismic qualification. The results confirm acceptability of the traditional approach which permit simplified analysis to demonstrate seismic qualificationqualification of CANDU feeder pipes

  4. Faecal nitrogen of browser and mixed feeder game species during ...

    African Journals Online (AJOL)

    Faecal nitrogen of browser and mixed feeder game species during different seasons. ... A practical measure of assessing periods of potential nutritional stress of game species is needed in the management of ... AJOL African Journals Online.

  5. Structural integrity investigations of feeder pipe ice plugging procedures

    International Nuclear Information System (INIS)

    Flaman, M.T.; Shah, N.N.

    1985-03-01

    A procedure involving the use of a liquid nitrogen cooled heat exchanger to form internal ice plugs in feeder pipes is routinely used in nuclear generating stations. The use of this procedure has caused concerns with regard to the safety of station maintenance personnel, and in regard to the integrity of the feeder pipes. This report describes the results of laboratory stress and pressure measurements which were performed on a feeder pipe section during ice plugging operations to investigate these concerns. From the results of this study, and from the results of previous studies of material behaviour at low temperatures, it has been determined that the ice plugging procedure can be performed on feeder pipes in a safe and effective manner

  6. SAFIRE - a robotic inspection system for CANDU feeders

    International Nuclear Information System (INIS)

    Buckingham, R.

    2011-01-01

    The condition of primary circuit feeder pipes in CANDU reactors is relevant to the commercial viability and plant life. One known wear mechanism is external fretting between feeder pipes and adjacent services or support structures, particularly within the Upper Feeder Cabinet (UFC). Fretting leads to wall thinning which must not exceed certain agreed limits. Chafe shields have been added to protect the feeder pipes. Regular inspections are required of the chafe shields, feeder pipes and other structures that may cause feeder damage. Historically, the dose received by inspectors conducting this work has been significant. For this reason Ontario Power Generation has invested in a remotely operated robot system to conduct visual inspections within the UFC. This system, called SAFIRE for 'Snake-Arm Feeder Inspection Robot Equipment' has been deployed at Pickering during 2010 and 2011 and has been used to inspect areas that are extremely difficult to inspect with existing manual techniques. The 2011 scope of work included inspection of a total of 660 feeder pipes in three UFC quadrants, in two reactors. The full scope was completed over a one-month period in Autumn 2011 in which SAFIRE was used during 23, twelve hour shifts. This included two periods each of 72 hours of continuous operation using multiple teams of operators. SAFIRE is remote controlled delivery system for multiple cameras to record still images and video. The main system elements include a snake-arm robot mounted on a mobile vehicle. It can be controlled from up to 500m away using a fibre/copper connection. The snake-arm is 2.2m long, 25mm wide and has 18 degrees of freedom. It is designed to snake between the rows of feeder pipes to inspect feeder/hanger interfaces, both above and below the feeder cabinet catwalks. Future upgrades offer the potential to add additional tools to increase functionality. This paper describes the SAFIRE development process from inception to operational experience gained

  7. SAFIRE - a robotic inspection system for CANDU feeders

    Energy Technology Data Exchange (ETDEWEB)

    Buckingham, R. [OC Robotics, Bristol (United Kingdom)

    2011-07-01

    The condition of primary circuit feeder pipes in CANDU reactors is relevant to the commercial viability and plant life. One known wear mechanism is external fretting between feeder pipes and adjacent services or support structures, particularly within the Upper Feeder Cabinet (UFC). Fretting leads to wall thinning which must not exceed certain agreed limits. Chafe shields have been added to protect the feeder pipes. Regular inspections are required of the chafe shields, feeder pipes and other structures that may cause feeder damage. Historically, the dose received by inspectors conducting this work has been significant. For this reason Ontario Power Generation has invested in a remotely operated robot system to conduct visual inspections within the UFC. This system, called SAFIRE for 'Snake-Arm Feeder Inspection Robot Equipment' has been deployed at Pickering during 2010 and 2011 and has been used to inspect areas that are extremely difficult to inspect with existing manual techniques. The 2011 scope of work included inspection of a total of 660 feeder pipes in three UFC quadrants, in two reactors. The full scope was completed over a one-month period in Autumn 2011 in which SAFIRE was used during 23, twelve hour shifts. This included two periods each of 72 hours of continuous operation using multiple teams of operators. SAFIRE is remote controlled delivery system for multiple cameras to record still images and video. The main system elements include a snake-arm robot mounted on a mobile vehicle. It can be controlled from up to 500m away using a fibre/copper connection. The snake-arm is 2.2m long, 25mm wide and has 18 degrees of freedom. It is designed to snake between the rows of feeder pipes to inspect feeder/hanger interfaces, both above and below the feeder cabinet catwalks. Future upgrades offer the potential to add additional tools to increase functionality. This paper describes the SAFIRE development process from inception to operational experience

  8. Mechanical loading regulates human MSC differentiation in a multi-layer hydrogel for osteochondral tissue engineering.

    Science.gov (United States)

    Steinmetz, Neven J; Aisenbrey, Elizabeth A; Westbrook, Kristofer K; Qi, H Jerry; Bryant, Stephanie J

    2015-07-01

    A bioinspired multi-layer hydrogel was developed for the encapsulation of human mesenchymal stem cells (hMSCs) as a platform for osteochondral tissue engineering. The spatial presentation of biochemical cues, via incorporation of extracellular matrix analogs, and mechanical cues, via both hydrogel crosslink density and externally applied mechanical loads, were characterized in each layer. A simple sequential photopolymerization method was employed to form stable poly(ethylene glycol)-based hydrogels with a soft cartilage-like layer of chondroitin sulfate and low RGD concentrations, a stiff bone-like layer with high RGD concentrations, and an intermediate interfacial layer. Under a compressive load, the variation in hydrogel stiffness within each layer produced high strains in the soft cartilage-like layer, low strains in the stiff bone-like layer, and moderate strains in the interfacial layer. When hMSC-laden hydrogels were cultured statically in osteochondral differentiation media, the local biochemical and matrix stiffness cues were not sufficient to spatially guide hMSC differentiation after 21 days. However dynamic mechanical stimulation led to differentially high expression of collagens with collagen II in the cartilage-like layer, collagen X in the interfacial layer and collagen I in the bone-like layer and mineral deposits localized to the bone layer. Overall, these findings point to external mechanical stimulation as a potent regulator of hMSC differentiation toward osteochondral cellular phenotypes. Copyright © 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  9. Urban Bird Feeders Dominated by a Few Species and Individuals

    Directory of Open Access Journals (Sweden)

    Josie A. Galbraith

    2017-08-01

    Full Text Available The practice of garden bird feeding is a global phenomenon, involving millions of people and vast quantities of food annually. Many people engage in the practice of feeding assuming that birds gain some benefit from the food they provide, yet recent studies have revealed the potential for detrimental impacts as well. However, there is still a paucity of information on the impacts of feeding, including the ubiquity of these impacts among and within feeder-visiting species. Consistency in feeder use among birds is likely an important determinant of this. Individual birds and species that make frequent use of feeders are more likely to experience both the benefits and detrimental impacts of supplementary food. We investigated patterns of feeder use by garden birds visiting experimental feeding stations in Auckland, New Zealand, with the specific aim of determining whether use of supplementary food was consistent or variable among individuals and species. We used camera traps as well as Radio Frequency Identification (RFID technology to examine intra- and interspecific feeder visitation patterns and to discern species associations. Eleven bird species were detected using feeding stations, however, two introduced species (house sparrow Passer domesticus and spotted dove Streptopelia chinensis dominated visitation events. These species were present at feeders most frequently, with the largest conspecific group sizes. Significant associations were detected among a number of species, suggesting interspecific interactions are important in determining feeder use. We also found within-species differences in feeder use for all focal species, with individual variation greatest in house sparrows. Furthermore, season had an important influence on most visitation parameters. The observed individual and species-specific differences in supplementary food resource use imply that the impacts of garden bird feeding are not universal. Crucially, particularly given

  10. Human fetal liver stromal cells that overexpress bFGF support growth and maintenance of human embryonic stem cells.

    Directory of Open Access Journals (Sweden)

    Jiafei Xi

    Full Text Available In guiding hES cell technology toward the clinic, one key issue to be addressed is to culture and maintain hES cells much more safely and economically in large scale. In order to avoid using mouse embryonic fibroblasts (MEFs we isolated human fetal liver stromal cells (hFLSCs from 14 weeks human fetal liver as new human feeder cells. hFLSCs feeders could maintain hES cells for 15 passages (about 100 days. Basic fibroblast growth factor (bFGF is known to play an important role in promoting self-renewal of human embryonic stem (hES cells. So, we established transgenic hFLSCs that stably express bFGF by lentiviral vectors. These transgenic human feeder cells--bFGF-hFLSCs maintained the properties of H9 hES cells without supplementing with any exogenous growth factors. H9 hES cells culturing under these conditions maintained all hES cell features after prolonged culture, including the developmental potential to differentiate into representative tissues of all three embryonic germ layers, unlimited and undifferentiated proliferative ability, and maintenance of normal karyotype. Our results demonstrated that bFGF-hFLSCs feeder cells were central to establishing the signaling network among bFGF, insulin-like growth factor 2 (IGF-2, and transforming growth factor β (TGF-β, thereby providing the framework in which hES cells were instructed to self-renew or to differentiate. We also found that the conditioned medium of bFGF-hFLSCs could maintain the H9 hES cells under feeder-free conditions without supplementing with bFGF. Taken together, bFGF-hFLSCs had great potential as feeders for maintaining pluripotent hES cell lines more safely and economically.

  11. Feeder use predicts both acquisition and transmission of a contagious pathogen in a North American songbird.

    Science.gov (United States)

    Adelman, James S; Moyers, Sahnzi C; Farine, Damien R; Hawley, Dana M

    2015-09-22

    Individual heterogeneity can influence the dynamics of infectious diseases in wildlife and humans alike. Thus, recent work has sought to identify behavioural characteristics that contribute disproportionately to individual variation in pathogen acquisition (super-receiving) or transmission (super-spreading). However, it remains unknown whether the same behaviours enhance both acquisition and transmission, a scenario likely to result in explosive epidemics. Here, we examined this possibility in an ecologically relevant host-pathogen system: house finches and their bacterial pathogen, Mycoplasma gallisepticum, which causes severe conjunctivitis. We examined behaviours likely to influence disease acquisition (feeder use, aggression, social network affiliations) in an observational field study, finding that the time an individual spends on bird feeders best predicted the risk of conjunctivitis. To test whether this behaviour also influences the likelihood of transmitting M. gallisepticum, we experimentally inoculated individuals based on feeding behaviour and tracked epidemics within captive flocks. As predicted, transmission was fastest when birds that spent the most time on feeders initiated the epidemic. Our results suggest that the same behaviour underlies both pathogen acquisition and transmission in this system and potentially others. Identifying individuals that exhibit such behaviours is critical for disease management. © 2015 The Author(s).

  12. Urbanization affects neophilia and risk-taking at bird-feeders

    Science.gov (United States)

    Tryjanowski, Piotr; Møller, Anders Pape; Morelli, Federico; Biaduń, Waldemar; Brauze, Tomasz; Ciach, Michał; Czechowski, Paweł; Czyż, Stanisław; Dulisz, Beata; Goławski, Artur; Hetmański, Tomasz; Indykiewicz, Piotr; Mitrus, Cezary; Myczko, Łukasz; Nowakowski, Jacek J.; Polakowski, Michał; Takacs, Viktoria; Wysocki, Dariusz; Zduniak, Piotr

    2016-06-01

    Urban environments cover vast areas with a high density of humans and their dogs and cats causing problems for exploitation of new resources by wild animals. Such resources facilitate colonization by individuals with a high level of neophilia predicting that urban animals should show more neophilia than rural conspecifics. We provided bird-feeders across urban environments in 14 Polish cities and matched nearby rural habitats, testing whether the presence of a novel item (a brightly coloured green object made out of gum with a tuft of hair) differentially delayed arrival at feeders in rural compared to urban habitats. The presence of a novel object reduced the number of great tits Parus major, but also the total number of all species of birds although differentially so in urban compared to rural areas. That was the case independent of the potentially confounding effects of temperature, population density of birds, and the abundance of cats, dogs and pedestrians. The number of great tits and the total number of birds attending feeders increased in urban compared to rural areas independent of local population density of birds. This implies that urban birds have high levels of neophilia allowing them to readily exploit unpredictable resources in urban environments.

  13. Assessment of CANDU feeders subject to flow accelerated corrosion

    Energy Technology Data Exchange (ETDEWEB)

    Iyer, S. [Atomic Energy of Canada Ltd., Mississauga, Ontario (Canada); Slade, J.P. [New Brunswick Power, Point Lepreau Generating Station, Lepreau, New Brunswick (Canada)

    2003-07-01

    'Full Text:' Inspections of CANDU feeders have indicated greater than expected wall thinning of outlet feeders. This wall thinning is attributed to Flow-Accelerated Corrosion (FAC). The rate of wall loss due to FAC is highest in the close radius bends near the end fitting. The minimum allowed thickness for a feeder pipes is based on design pressure during the design stage. Extended operation of the thinned feeders beyond their design basis, i.e., operation of feeders with thickness below design pressure based minimum thickness has economic benefits for the utilities. In such cases, it is important to establish the remaining life and evaluate the adequacy of the components for safe operation. ASME Code Case N-597 provides the guidelines for acceptance for continued service of Classes 2 and 3 piping components experiencing wall thinning during operation. However, for Class 1 systems, the Code Case recommends that the owner develop the methodology and criteria for the assessment of wall thinning. Therefore, under the CANDU Owner's Group's (COG) Feeder Integrity Joint Program (FIJP), the 'Fitness for Service Guidelines (FFSG) for Feeders Affected by Wall Thinning in Operating CANDU Reactors' was developed and subsequently conditionally approved by CNSC. This paper illustrates the underlying concepts in the FFSG methodology and its benefits to utilities. Specific examples of the application and benefits of the FFSG at Point Lepreau G.S. are described in this paper. The assessment of feeders is based on the requirements of the construction Code (Section III of the ASME Boiler and Pressure Vessel Code): The following points briefly describe the assessment methodology. Satisfying the requirements of NB-3650 for design and service loadings are sufficient for continued service and extended life if the predicted minimum wall thickness of the component is greater than or equal to 90% of the pressure based thickness calculated as per NB-3641. The B

  14. Object categorization by wild ranging birds-Winter feeder experiments.

    Science.gov (United States)

    Nováková, Nela; Veselý, Petr; Fuchs, Roman

    2017-10-01

    The object categorization is only scarcely studied using untrained wild ranging animals and relevant stimuli. We tested the importance of the spatial position of features salient for categorization of a predator using wild ranging birds (titmice) visiting a winter feeder. As a relevant stimulus we used a dummy of a raptor, the European sparrowhawk (Accipiter nisus), placed at the feeding location. This dummy was designed to be dismantled into three parts and rearranged with the head in the correct position, in the middle or at the bottom of the dummy. When the birds had the option of visiting an alternative feeder with a dummy pigeon, they preferred this option to visiting the feeder with the dummy sparrowhawk with the head in any of the three positions. When the birds had the option of visiting an alternative feeder with an un-rearranged dummy sparrowhawk, they visited both feeders equally often, and very scarcely. This suggests that the titmice considered all of the sparrowhawk modifications as being dangerous, and equally dangerous as the un-rearranged sparrowhawk. The position of the head was not the most important cue for categorization. The presence of the key features was probably sufficient for categorization, and their mutual spatial position was of lower importance. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Seismic analysis of ITER fourth PF (Poloidal Field Coil) feeder

    International Nuclear Information System (INIS)

    Liu, Sumei; Chen, Wei; Song, Yuntao; Ni, Xiaojun; Wang, Zhongwei; Chen, Yonghua; Gong, Chenyu

    2014-01-01

    The ITER feeder systems connect the ITER magnet systems located inside the main cryostat to the cryo-plant, power-supply and control system interfaces outside the cryostat. The main purpose of the feeders is to convey the cryogenic supply and electrical power to the coils as well as house the instrumentation wiring. The PF busbar which carries 52 kA current will suffer from high Lorentz force due to the background magnetic field inspired by the coils and the self-field between every pair of busbars. Except their mechanical strength and thermal insulation performance must be achieved, the dynamic mechanism on PF structure should be assessed. This paper presents the simulation and seismic analysis on ITER 4th PF feeder including the Coil Terminal Box and S-bend Box (CTB and SBB), the Cryostat Feed-through (CFT), the In-Cryostat-Feeder (ICF), especially for the ground supports and main outer-tube firstly. This analysis aims to study seismic resistance on system design under local seismograms with floor response spectrum, the structural response vibration mode and response duration results of displacement, membrane stress, and bending stress on structure under different directions actuating signals were obtained by using the single-seismic spectrum analysis and Dead Weight analysis respectively. Based on the simulative and analytical results, the system seismic resistance and the integrity of the support structure in the 4th PF feeder have been studied and the detail design confirmed

  16. Electrical impedance of layered atherosclerotic plaques on human aortas

    NARCIS (Netherlands)

    C.J. Slager (Cornelis); A.C. Phaff; C.E. Essed; N. Bom (Klaas); J.C.H. Schuurbiers (Johan); P.W.J.C. Serruys (Patrick)

    1992-01-01

    textabstractElectrical impedance measurements were performed on 13 atherosclerotic human aortic segments at 67 measuring spots in order to determine whether or not on the basis of these data a distinction can be made between atherosclerotic lesions and normal tissue. Stenosis localization and

  17. Urban and rural habitats differ in number and type of bird feeders and in bird species consuming supplementary food.

    Science.gov (United States)

    Tryjanowski, Piotr; Skórka, Piotr; Sparks, Tim H; Biaduń, Waldemar; Brauze, Tomasz; Hetmański, Tomasz; Martyka, Rafał; Indykiewicz, Piotr; Myczko, Łukasz; Kunysz, Przemysław; Kawa, Piotr; Czyż, Stanisław; Czechowski, Paweł; Polakowski, Michał; Zduniak, Piotr; Jerzak, Leszek; Janiszewski, Tomasz; Goławski, Artur; Duduś, Leszek; Nowakowski, Jacek J; Wuczyński, Andrzej; Wysocki, Dariusz

    2015-10-01

    Bird feeding is one of the most widespread direct interactions between man and nature, and this has important social and environmental consequences. However, this activity can differ between rural and urban habitats, due to inter alia habitat structure, human behaviour and the composition of wintering bird communities. We counted birds in 156 squares (0.25 km(2) each) in December 2012 and again in January 2013 in locations in and around 26 towns and cities across Poland (in each urban area, we surveyed 3 squares and also 3 squares in nearby rural areas). At each count, we noted the number of bird feeders, the number of bird feeders with food, the type of feeders, additional food supplies potentially available for birds (bread offered by people, bins) and finally the birds themselves. In winter, urban and rural areas differ in the availability of food offered intentionally and unintentionally to birds by humans. Both types of food availability are higher in urban areas. Our findings suggest that different types of bird feeder support only those species specialized for that particular food type and this relationship is similar in urban and rural areas.

  18. A Markov chain model for CANDU feeder pipe degradation

    International Nuclear Information System (INIS)

    Datla, S.; Dinnie, K.; Usmani, A.; Yuan, X.-X.

    2008-01-01

    There is need for risk based approach to manage feeder pipe degradation to ensure safe operation by minimizing the nuclear safety risk. The current lack of understanding of some fundamental degradation mechanisms will result in uncertainty in predicting the rupture frequency. There are still concerns caused by uncertainties in the inspection techniques and engineering evaluations which should be addressed in the current procedures. A probabilistic approach is therefore useful in quantifying the risk and also it provides a tool for risk based decision making. This paper discusses the application of Markov chain model for feeder pipes in order to predict and manage the risks associated with the existing and future aging-related feeder degradation mechanisms. The major challenge in the approach is the lack of service data in characterizing the transition probabilities of the Markov model. The paper also discusses various approaches in estimating plant specific degradation rates. (author)

  19. Configuration System for Simulation Based Design of Vibratory Bowl Feeders

    DEFF Research Database (Denmark)

    Hansson, Michael Natapon; Mathiesen, Simon; Ellekilde, Lars-Peter

    2017-01-01

    Vibratory bowl feeders are still among the most commonly used production equipment for automated part feeding, where parts are correctly oriented for further manipulation by being conveyed through a set of orienting devices. Designing vibratory bowl feeders involves selecting and sequencing...... a number of these devices that either reorients or rejects the part until a desirable orientation is achieved. To aid the designer in this task, this work presents a configuration system where knowledge of the behaviour for each device is acquired through dynamic simulation, and used to solve...

  20. Human Intestinal Fluid Layer Separation: The Effect On Colloidal Structures & Solubility Of Lipophilic Compounds.

    Science.gov (United States)

    Danny, Riethorst; Amitava, Mitra; Filippos, Kesisoglou; Wei, Xu; Jan, Tack; Joachim, Brouwers; Patrick, Augustijns

    2018-05-23

    In addition to individual intestinal fluid components, colloidal structures are responsible for enhancing the solubility of lipophilic compounds. The present study investigated the link between as well as the variability in the ultrastructure of fed state human intestinal fluids (FeHIF) and their solubilizing capacity for lipophilic compounds. For this purpose, FeHIF samples from 10 healthy volunteers with known composition and ultrastructure were used to determine the solubility of four lipophilic compounds. In light of the focus on solubility and ultrastructure, the study carefully considered the methodology of solubility determination in relation to colloid composition and solubilizing capacity of FeHIF. To determine the solubilizing capacity of human and simulated intestinal fluids, the samples were saturated with the compound of interest, shaken for 24 h, and centrifuged. When using FeHIF, solubilities were determined in the micellar layer of FeHIF, i.e. after removing the upper (lipid) layer (standard procedure), as well as in 'full' FeHIF (without removal of the upper layer). Compound concentrations were determined using HPLC-UV/fluorescence. To link the solubilizing capacity with the ultrastructure, all human and simulated fluids were imaged using transmission electron microscopy (TEM) before and after centrifugation and top layer (lipid) removal. Comparing the ultrastructure and solubilizing capacity of individual FeHIF samples demonstrated a high intersubject variability in postprandial intestinal conditions. Imaging of FeHIF after removal of the upper layer clearly showed that only micellar structures remain in the lower layer. This observation suggests that larger colloids such as vesicles and lipid droplets are contained in the upper, lipid layer. The solubilizing capacity of most FeHIF samples substantially increased with inclusion of this lipid layer. The relative increase in solubilizing capacity upon inclusion of the lipid layer was most pronounced

  1. Human convective boundary layer and its impact on personal exposure

    DEFF Research Database (Denmark)

    Licina, Dusan

    generated by heat sources are gaining more prominent influence in space airflow formation and on the indoor environment overall. In such spaces with low air supply velocity, air mixing is minimized and the pollution emitted from localized indoor sources is non-uniformly distributed. The large spatial......People spend most of their time indoors and they are constantly exposed to pollution that affects their health, comfort and productivity. Due to strong economic and environmental pressures to reduce building energy consumption, low air velocity design is gaining popularity; hence buoyancy flows...... in inaccurate exposure prediction. This highlights the importance of a detailed understanding of the complex air movements that take place in the vicinity of the human body and their impact on personal exposure. The two objectives of the present work are: (i) to examine the extent to which the room air...

  2. Differentiation of oligodendrocyte progenitor cells from dissociated monolayer and feeder-free cultured pluripotent stem cells.

    Science.gov (United States)

    Yamashita, Tomoko; Miyamoto, Yuki; Bando, Yoshio; Ono, Takashi; Kobayashi, Sakurako; Doi, Ayano; Araki, Toshihiro; Kato, Yosuke; Shirakawa, Takayuki; Suzuki, Yutaka; Yamauchi, Junji; Yoshida, Shigetaka; Sato, Naoya

    2017-01-01

    Oligodendrocytes myelinate axons and form myelin sheaths in the central nervous system. The development of therapies for demyelinating diseases, including multiple sclerosis and leukodystrophies, is a challenge because the pathogenic mechanisms of disease remain poorly understood. Primate pluripotent stem cell-derived oligodendrocytes are expected to help elucidate the molecular pathogenesis of these diseases. Oligodendrocytes have been successfully differentiated from human pluripotent stem cells. However, it is challenging to prepare large amounts of oligodendrocytes over a short amount of time because of manipulation difficulties under conventional primate pluripotent stem cell culture methods. We developed a proprietary dissociated monolayer and feeder-free culture system to handle pluripotent stem cell cultures. Because the dissociated monolayer and feeder-free culture system improves the quality and growth of primate pluripotent stem cells, these cells could potentially be differentiated into any desired functional cells and consistently cultured in large-scale conditions. In the current study, oligodendrocyte progenitor cells and mature oligodendrocytes were generated within three months from monkey embryonic stem cells. The embryonic stem cell-derived oligodendrocytes exhibited in vitro myelinogenic potency with rat dorsal root ganglion neurons. Additionally, the transplanted oligodendrocyte progenitor cells differentiated into myelin basic protein-positive mature oligodendrocytes in the mouse corpus callosum. This preparative method was used for human induced pluripotent stem cells, which were also successfully differentiated into oligodendrocyte progenitor cells and mature oligodendrocytes that were capable of myelinating rat dorsal root ganglion neurons. Moreover, it was possible to freeze, thaw, and successfully re-culture the differentiating cells. These results showed that embryonic stem cells and human induced pluripotent stem cells maintained in a

  3. Optical coherence tomography noise modeling and fundamental bounds on human retinal layer segmentation accuracy (Conference Presentation)

    Science.gov (United States)

    DuBose, Theodore B.; Milanfar, Peyman; Izatt, Joseph A.; Farsiu, Sina

    2016-03-01

    The human retina is composed of several layers, visible by in vivo optical coherence tomography (OCT) imaging. To enhance diagnostics of retinal diseases, several algorithms have been developed to automatically segment one or more of the boundaries of these layers. OCT images are corrupted by noise, which is frequently the result of the detector noise and speckle, a type of coherent noise resulting from the presence of several scatterers in each voxel. However, it is unknown what the empirical distribution of noise in each layer of the retina is, and how the magnitude and distribution of the noise affects the lower bounds of segmentation accuracy. Five healthy volunteers were imaged using a spectral domain OCT probe from Bioptigen, Inc, centered at 850nm with 4.6µm full width at half maximum axial resolution. Each volume was segmented by expert manual graders into nine layers. The histograms of intensities in each layer were then fit to seven possible noise distributions from the literature on speckle and image processing. Using these empirical noise distributions and empirical estimates of the intensity of each layer, the Cramer-Rao lower bound (CRLB), a measure of the variance of an estimator, was calculated for each boundary layer. Additionally, the optimum bias of a segmentation algorithm was calculated, and a corresponding biased CRLB was calculated, which represents the improved performance an algorithm can achieve by using prior knowledge, such as the smoothness and continuity of layer boundaries. Our general mathematical model can be easily adapted for virtually any OCT modality.

  4. Microplastic in a macro filter feeder: humpback whale Megaptera novaeangliae

    NARCIS (Netherlands)

    Besseling, E.; Foekema, E.M.; Franeker, van J.A.; Leopold, M.F.; Bravo Rebolledo, E.; Kuehn, S.; Mielke, L.; Heberle-Bors, E.; Ijzer, J.; Kamminga, P.; Koelmans, A.A.

    2015-01-01

    Marine filter feeders are exposed to microplastic because of their selection of small particles as food source. Baleen whales feed by filtering small particles from large water volumes. Macroplastic was found in baleen whales before. This study is the first to show the presence of microplastic in

  5. Optimisation of Trap Design for Vibratory Bowl Feeders

    DEFF Research Database (Denmark)

    Mathiesen, Simon; Sørensen, Lars Carøe; Kraft, Dirk

    2018-01-01

    Vibratory bowl feeders (VBFs) are a widely used option for industrial part feeding, but their design is still largely manual. A subtask of VBF design is determining an optimal parameter set for the passive devices, called traps, which the VBF uses to ensure correct part orientation. This paper...

  6. Microplastic in a macro filter feeder: Humpback whale Megaptera novaeangliae.

    NARCIS (Netherlands)

    E., Besseling,; E.M., Foekema,; J.A. van, Franeker; Leopold, Mardik F; Kuhn, S.; Bravo Rebolledo, E.L.; Hese, E.; Mielke, L.; IJzer, J.|info:eu-repo/dai/nl/304839663; Kamminga, P.; Koelmans, A.A.

    2015-01-01

    Marine filter feeders are exposed to microplastic because of their selection of small particles as food source. Baleen whales feed by filtering small particles from large water volumes. Macroplastic was found in baleen whales before. This study is the first to show the presence of microplastic in

  7. A hybrid evolutionary algorithm for distribution feeder reconfiguration

    Indian Academy of Sciences (India)

    the reconfiguration of distribution networks has been proposed by .... An effective strategy to increase the loading margin of heavily loaded feeders is to ... social animals such as a flock of birds, a school of fish or a group of people that pursue.

  8. Transport of gaseous pollutants by convective boundary layer around a human body

    DEFF Research Database (Denmark)

    Licina, Dusan; Melikov, Arsen Krikor; Sekhar, Chandra

    2015-01-01

    This study investigates the ability of the human convective boundary layer to transport pollution in a quiescent indoor environment. The impact of the source location in the vicinity of a human body is examined in relation to pollution distribution in the breathing zone and the thickness...... of the pollution boundary layer. The study, in addition, evaluates the effects of the room air temperature, table positioning, and seated body inclination. The human body is represented by a thermal manikin that has a body shape, size, and surface temperature that resemble those of a real person. The results show...... at the upper back or behind the chair. The results also indicate that a decrease in personal exposure to pollutants released from or around the human body increases the extent to which the pollution spreads to the surroundings. Reducing the room air temperature or backward body inclination intensifies...

  9. Novel Methods to Determine Feeder Locational PV Hosting Capacity and PV Impact Signatures

    Energy Technology Data Exchange (ETDEWEB)

    Reno, Matthew J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Coogan, Kyle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Seuss, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Broderick, Robert Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-05-01

    Often PV hosting capacity analysis is performed for a limited number of distribution feeders. For medium - voltage distribution feeders, previous results generally analyze less than 20 feeders, and then the results are extrapolated out to similar types of feeders. Previous hosting capacity research has often focused on determining a single value for the hosting capacity for the entire feeder, whereas this research expands previous hosting capacity work to investigate all the regions of the feeder that may allow many different hosting capacity values wit h an idea called locational hosting capacity (LHC)to determine the largest PV size that can be interconnected at different locations (buses) on the study feeders. This report discusses novel methods for analyzing PV interconnections with advanced simulati on methods. The focus is feeder and location - specific impacts of PV that determine the locational PV hosting capacity. Feeder PV impact signature are used to more precisely determine the local maximum hosting capacity of individual areas of the feeder. T he feeder signature provides improved interconnection screening with certain zones that show the risk of impact to the distribution feeder from PV interconnections.

  10. Syllabic discrimination in premature human infants prior to complete formation of cortical layers

    OpenAIRE

    Mahmoudzadeh, Mahdi; Dehaene-Lambertz, Ghislaine; Fournier, Marc; Kongolo, Guy; Goudjil, Sabrina; Dubois, Jessica; Grebe, Reinhard; Wallois, Fabrice

    2013-01-01

    The ontogeny of linguistic functions in the human brain remains elusive. Although some auditory capacities are described before term, whether and how such immature cortical circuits might process speech are unknown. Here we used functional optical imaging to evaluate the cerebral responses to syllables at the earliest age at which cortical responses to external stimuli can be recorded in humans (28- to 32-wk gestational age). At this age, the cortical organization in layers is not completed. ...

  11. Round-bale feeder design affects hay waste and economics during horse feeding.

    Science.gov (United States)

    Martinson, K; Wilson, J; Cleary, K; Lazarus, W; Thomas, W; Hathaway, M

    2012-03-01

    Many horse owners find round bales convenient, less labor intensive, and more affordable than other hay types, but report an inability to control horse BW gain and excessive hay waste. The objectives were to compare hay waste, hay intake, and payback of 9 round-bale feeders and a no-feeder control when used during horse feeding. Nine round-bale feeders were tested: Cinch Net, Cone, Covered Cradle, Hayhut, Hay Sleigh, Ring, Tombstone, Tombstone Saver, and Waste Less. Each feeder design was placed on the ground in a dirt paddock. Five groups of 5 horses were fed in rotation for a 4-d period with each feeder. Every fourth day, groups were rotated among paddocks and a new round bale was placed in each feeder. In the 5 paddocks used, 5 feeders were installed for d 1 through 20, and the remaining 4 feeders and no-feeder control were installed for d 21 through 40. Groups of horses were sequentially assigned to feeders using two 5 × 5 Latin squares, the first for d 1 through 20, the second for d 21 through 40. Horse groups of similar age, BW, breed, and sex were formed from 25 Quarter Horse and Thoroughbred geldings and open mares (means: 11 yr; 541 kg of BW). Hay on the ground surrounding the feeder was collected daily, dried, and weighed. The total amount of hay removed around each feeder for a 4-d period was considered waste. Dry matter intake was estimated as the difference between hay disappearance and waste. Number of months for the reduction in waste to repay feeder cost (payback) were calculated using hay valued at $110/t, and improved feeder efficiency over the control. Feeder design did not affect hay intake (P > 0.05); all feeders resulted in an estimated hay intake of 2.0 to 2.4% BW; the no-feeder control resulted in a reduced intake of 1.3% BW (P = 0.001). Mean percentage of hay waste differed among feeders (P feeder control, 57%. Feeder design also affected payback (P feeder design affected hay waste and payback, but not estimated hay intake or BW change

  12. Feeding Against Gravity with Spot Feeders in High Silicon Ductile Iron

    DEFF Research Database (Denmark)

    Vedel-Smith, Nikolaj Kjelgaard; Tiedje, Niels Skat

    2014-01-01

    and classified using X-ray imaging and ultrasound analysis. The effect of the different feeder configurations were classified in reference to defect location, sleeve material, and feeder type, modulus, and location. The analysis showed that exothermal feeder sleeves with the right configurations can feed up......-hill against gravity. This effect may contribute to the thermal expansion created by the exothermal reaction. It was also found that the optimum feeder size does not scale linearly with the casting modulus but that larger casting modulus requires relatively smaller modulus feeders. The thermal gradient created...

  13. Feederism: an exaggeration of a normative mate selection preference?

    Science.gov (United States)

    Terry, Lesley L; Suschinsky, Kelly D; Lalumière, Martin L; Vasey, Paul L

    2012-02-01

    Quinsey and Lalumière (1995) suggested that some, if not most, paraphilias are exaggerated manifestations of more normative and functional mate selection preferences. The present study tested whether Feederism, a fat fetish focused on erotic eating, feeding, and gaining weight, is an exaggeration of a sexual arousal pattern commonly seen in the general population. Thirty participants (15 men and 15 women) recruited from the general population were assessed using penile plethysmography and vaginal photoplethysmography, respectively. None of the participants were self-identified Feeders or Feedees. Participants were shown sexual, neutral, and feeding still images while listening to audio recordings of sexual, neutral, and feeding stories. Participants did not genitally respond to feeding stimuli. However, both men and women subjectively rated feeding stimuli as more sexually arousing than neutral stimuli. We discuss the discordance between physiological and self-reported sexual arousal in the context of sex differences in sexual concordance and implications for future research.

  14. Digital optical feeder links system for broadband geostationary satellite

    Science.gov (United States)

    Poulenard, Sylvain; Mège, Alexandre; Fuchs, Christian; Perlot, Nicolas; Riedi, Jerome; Perdigues, Josep

    2017-02-01

    An optical link based on a multiplex of wavelengths at 1.55μm is foreseen to be a valuable solution for the feeder link of the next generation of high-throughput geostationary satellite. The main satellite operator specifications for such link are an availability of 99.9% over the year, a capacity around 500Gbit/s and to be bent-pipe. Optical ground station networks connected to Terabit/s terrestrial fibers are proposed. The availability of the optical feeder link is simulated over 5 years based on a state-of-the-art cloud mask data bank and an atmospheric turbulence strength model. Yearly and seasonal optical feeder link availabilities are derived and discussed. On-ground and on-board terminals are designed to be compliant with 10Gbit/s per optical channel data rate taking into account adaptive optic systems to mitigate the impact of atmospheric turbulences on single-mode optical fiber receivers. The forward and return transmission chains, concept and implementation, are described. These are based on a digital transparent on-off keying optical link with digitalization of the DVB-S2 and DVB-RCS signals prior to the transmission, and a forward error correcting code. In addition, the satellite architecture is described taking into account optical and radiofrequency payloads as well as their interfaces.

  15. Clonal proliferation of cultured nonmalignant and malignant human breast epithelia

    International Nuclear Information System (INIS)

    Smith, H.S.; Lan, S.; Ceriani, R.; Hackett, A.J.; Stampfer, M.R.

    1981-01-01

    We have developed a method for clonal growth of human mammary epithelial cells of both nonmalignant and malignant origin. Plating efficiencies of 1 to 50% were obtained by seeding second-passage mammary epithelial cells on fibroblast feeder layers in an enriched medium composed of various hormones and growth factors, as well as conditioned media from three specific human cell lines. Single mammary epithelial cells seeded sparsely onto the fibroblasts underwent at least eight population doublings to form large, readily visible colonies. Optimal colony formation required both feeder cells and the enriched medium. Epithelial colonies containing at least 16 cells were visible 5 days postseeding, and these colonies continued to grow progressively. Plating efficiency and colony size were similar on ultraviolet-irradiated or nonirradiated fibroblasts. The number of colonies formed was proportional to the number of epithelial cells plated. The colonies were identified as epithelial by the presence of human mammary epithelial antigens

  16. Replication of swine and human influenza viruses in juvenile and layer turkey hens.

    Science.gov (United States)

    Ali, Ahmed; Yassine, Hadi; Awe, Olusegun O; Ibrahim, Mahmoud; Saif, Yehia M; Lee, Chang-Won

    2013-04-12

    Since the first reported isolation of swine influenza viruses (SIVs) in turkeys in the 1980s, transmission of SIVs to turkeys was frequently documented. Recently, the 2009 pandemic H1N1 virus, that was thought to be of swine origin, was detected in turkeys with a severe drop in egg production. In this study, we assessed the infectivity of different mammalian influenza viruses including swine, pandemic H1N1 and seasonal human influenza viruses in both juvenile and layer turkeys. In addition, we investigated the potential influenza virus dissemination in the semen of experimentally infected turkey toms. Results showed that all mammalian origin influenza viruses tested can infect turkeys. SIVs were detected in respiratory and digestive tracts of both juvenile and layer turkeys. Variations in replication efficiencies among SIVs were observed especially in the reproductive tract of layer turkeys. Compared to SIVs, limited replication of seasonal human H1N1 and no detectable replication of recent human-like swine H1N2, pandemic H1N1 and seasonal human H3N2 viruses was noticed. All birds seroconverted to all tested viruses regardless of their replication level. In turkey toms, we were able to detect swine H3N2 virus in semen and reproductive tract of infected toms by real-time RT-PCR although virus isolation was not successful. These data suggest that turkey hens could be affected by diverse influenza strains especially SIVs. Moreover, the differences in the replication efficiency we demonstrated among SIVs and between SIV and human influenza viruses in layer turkeys suggest a possible use of turkeys as an animal model to study host tropism and pathogenesis of influenza viruses. Our results also indicate a potential risk of venereal transmission of influenza viruses in turkeys. Copyright © 2012 Elsevier B.V. All rights reserved.

  17. Quantitative Measurement of Dissection Resistance in Intimal and Medial Layers of Human Coronary Arteries

    Science.gov (United States)

    Wang, Ying; Johnson, John A.; Spinale, Francis G.; Sutton, Michael A.; Lessner, Susan M.

    2014-01-01

    The left anterior descending (LAD) coronary artery is the most frequently involved vessel in coronary artery dissection, a cause of acute coronary syndrome or sudden cardiac death. The biomechanical mechanisms underlying arterial dissection are not well understood. This study investigated the dissection properties of LAD specimens harvested from explanted hearts at the time of cardiac transplantation, from patients with primary dilated cardiomyopathy (n=12). Using a previously validated approach uniquely modified for these human LAD specimens, we quantified the local energy release rate, G, within different arterial layers during experimental dissection events (tissue tearing). Results show that the mean values of G during arterial dissection within the intima and within the media in human LADs are 20.7±16.5 J/m2 and 10.3±5.0 J/m2, respectively. The difference in dissection resistance between tearing events occurring within the intima and within the media is statistically significant. Our data fall in the same order of magnitude as most previous measurements of adhesive strength in other human arteries, with the differences in measured values of G within the layers most likely due to histologically observed differences in the structure and composition of arterial layers. PMID:24729631

  18. Comparative Proteomic Analysis of Supportive and Unsupportive Extracellular Matrix Substrates for Human Embryonic Stem Cell Maintenance*

    Science.gov (United States)

    Soteriou, Despina; Iskender, Banu; Byron, Adam; Humphries, Jonathan D.; Borg-Bartolo, Simon; Haddock, Marie-Claire; Baxter, Melissa A.; Knight, David; Humphries, Martin J.; Kimber, Susan J.

    2013-01-01

    Human embryonic stem cells (hESCs) are pluripotent cells that have indefinite replicative potential and the ability to differentiate into derivatives of all three germ layers. hESCs are conventionally grown on mitotically inactivated mouse embryonic fibroblasts (MEFs) or feeder cells of human origin. In addition, feeder-free culture systems can be used to support hESCs, in which the adhesive substrate plays a key role in the regulation of stem cell self-renewal or differentiation. Extracellular matrix (ECM) components define the microenvironment of the niche for many types of stem cells, but their role in the maintenance of hESCs remains poorly understood. We used a proteomic approach to characterize in detail the composition and interaction networks of ECMs that support the growth of self-renewing hESCs. Whereas many ECM components were produced by supportive and unsupportive MEF and human placental stromal fibroblast feeder cells, some proteins were only expressed in supportive ECM, suggestive of a role in the maintenance of pluripotency. We show that identified candidate molecules can support attachment and self-renewal of hESCs alone (fibrillin-1) or in combination with fibronectin (perlecan, fibulin-2), in the absence of feeder cells. Together, these data highlight the importance of specific ECM interactions in the regulation of hESC phenotype and provide a resource for future studies of hESC self-renewal. PMID:23658023

  19. A mid-layer model for human reliability analysis: understanding the cognitive causes of human failure events

    International Nuclear Information System (INIS)

    Shen, Song-Hua; Chang, James Y.H.; Boring, Ronald L.; Whaley, April M.; Lois, Erasmia; Langfitt Hendrickson, Stacey M.; Oxstrand, Johanna H.; Forester, John Alan; Kelly, Dana L.; Mosleh, Ali

    2010-01-01

    The Office of Nuclear Regulatory Research (RES) at the US Nuclear Regulatory Commission (USNRC) is sponsoring work in response to a Staff Requirements Memorandum (SRM) directing an effort to establish a single human reliability analysis (HRA) method for the agency or guidance for the use of multiple methods. As part of this effort an attempt to develop a comprehensive HRA qualitative approach is being pursued. This paper presents a draft of the method's middle layer, a part of the qualitative analysis phase that links failure mechanisms to performance shaping factors. Starting with a Crew Response Tree (CRT) that has identified human failure events, analysts identify potential failure mechanisms using the mid-layer model. The mid-layer model presented in this paper traces the identification of the failure mechanisms using the Information-Diagnosis/Decision-Action (IDA) model and cognitive models from the psychological literature. Each failure mechanism is grouped according to a phase of IDA. Under each phase of IDA, the cognitive models help identify the relevant performance shaping factors for the failure mechanism. The use of IDA and cognitive models can be traced through fault trees, which provide a detailed complement to the CRT.

  20. A Mid-Layer Model for Human Reliability Analysis: Understanding the Cognitive Causes of Human Failure Events

    Energy Technology Data Exchange (ETDEWEB)

    Stacey M. L. Hendrickson; April M. Whaley; Ronald L. Boring; James Y. H. Chang; Song-Hua Shen; Ali Mosleh; Johanna H. Oxstrand; John A. Forester; Dana L. Kelly; Erasmia L. Lois

    2010-06-01

    The Office of Nuclear Regulatory Research (RES) is sponsoring work in response to a Staff Requirements Memorandum (SRM) directing an effort to establish a single human reliability analysis (HRA) method for the agency or guidance for the use of multiple methods. As part of this effort an attempt to develop a comprehensive HRA qualitative approach is being pursued. This paper presents a draft of the method’s middle layer, a part of the qualitative analysis phase that links failure mechanisms to performance shaping factors. Starting with a Crew Response Tree (CRT) that has identified human failure events, analysts identify potential failure mechanisms using the mid-layer model. The mid-layer model presented in this paper traces the identification of the failure mechanisms using the Information-Diagnosis/Decision-Action (IDA) model and cognitive models from the psychological literature. Each failure mechanism is grouped according to a phase of IDA. Under each phase of IDA, the cognitive models help identify the relevant performance shaping factors for the failure mechanism. The use of IDA and cognitive models can be traced through fault trees, which provide a detailed complement to the CRT.

  1. Derivation and characterization of the NYSCFe003-A human embryonic stem cell line

    Directory of Open Access Journals (Sweden)

    Ana Sevilla

    2017-12-01

    Full Text Available The human embryonic stem cell line NYSCFe003-A was derived from a day 5 to day 6 blastocyst in feeder-free and antibiotic free conditions. The blastocyst was voluntarily donated for research as surplus after in vitro fertilization treatment following informed consent. The NYSCFe003-A line expresses all the pluripotency markers and has the potential to differentiate into all three germ layers in vitro. The line presents normal karyotype and is mycoplasma free.

  2. Progress and Challenges in Developing Reference Data Layers for Human Population Distribution and Built Infrastructure

    Science.gov (United States)

    Chen, R. S.; Yetman, G.; de Sherbinin, A. M.

    2015-12-01

    Understanding the interactions between environmental and human systems, and in particular supporting the applications of Earth science data and knowledge in place-based decision making, requires systematic assessment of the distribution and dynamics of human population and the built human infrastructure in conjunction with environmental variability and change. The NASA Socioeconomic Data and Applications Center (SEDAC) operated by the Center for International Earth Science Information Network (CIESIN) at Columbia University has had a long track record in developing reference data layers for human population and settlements and is expanding its efforts on topics such as intercity roads, reservoirs and dams, and energy infrastructure. SEDAC has set as a strategic priority the acquisition, development, and dissemination of data resources derived from remote sensing and socioeconomic data on urban land use change, including temporally and spatially disaggregated data on urban change and rates of change, the built infrastructure, and critical facilities. We report here on a range of past and ongoing activities, including the Global Human Settlements Layer effort led by the European Commission's Joint Research Centre (JRC), the Global Exposure Database for the Global Earthquake Model (GED4GEM) project, the Global Roads Open Access Data Working Group (gROADS) of the Committee on Data for Science and Technology (CODATA), and recent work with ImageCat, Inc. to improve estimates of the exposure and fragility of buildings, road and rail infrastructure, and other facilities with respect to selected natural hazards. New efforts such as the proposed Global Human Settlement indicators initiative of the Group on Earth Observations (GEO) could help fill critical gaps and link potential reference data layers with user needs. We highlight key sectors and themes that require further attention, and the many significant challenges that remain in developing comprehensive, high quality

  3. Some software issues in mapping of power distribution feeders

    International Nuclear Information System (INIS)

    Mufti, I.A.

    1994-01-01

    This paper is about the in-house developed software for distribution feeders mapping project. It first gives birds eye view of the project, highlight its technical complexity in management and logistics, introduced by sheer size of the project. It gives an overview of the software developed and the moves on to describe circuit tracing, circuit model, leaves isolation (for tree structured network) and backtracking in more detail among many different parts of software, description of all which is not possible because of space limitations. (author)

  4. Stress analysis of feeder bends using neutrons: new results and cumulative impacts

    Energy Technology Data Exchange (ETDEWEB)

    Banks, D.; Donaberger, R. [Canadian Neutron Beam Centre, Chalk River, ON (Canada); Leitch, B. [Atomic Energy of Canada Limited, Chalk River, ON (Canada); Rogge, R.B. [Canadian Neutron Beam Centre, Chalk River, ON (Canada)

    2014-07-01

    Neutron diffraction has played a vital role in stress analysis of bends in carbon steel pipes, known as feeder pipes, in CANDU reactors. Due to incidents of cracking of feeders, extensive R&D programs to manage feeder cracking have been implemented over about ten years. We review the cumulative impacts of this research from the view point of the stress analysis using neutrons, and present new results by examining a feeder bend with a partial crack both experimentally using neutron diffraction and theoretically using a finite element model. (author)

  5. limit loads for wall-thinning feeder pipes under combined bending and internal pressure

    International Nuclear Information System (INIS)

    Je, Jin Ho; Lee, Kuk Hee; Chung, Ha Joo; Kim, Ju Hee; Han, Jae Jun; Kim, Yun Jae

    2009-01-01

    Flow Accelerated Corrosion (FAC) during inservice conditions produces local wall-thinning in the feeder pipes of CANDU. The Wall-thinning in the feeder pipes is main degradation mechanisms affecting the integrity of piping systems. This paper discusses the integrity assessment of wall-thinned feeder pipes using limit load analysis. Based on finite element limit analyses, this paper compare limit loads for wall-thinning feeder pipes under combined bending and internal pressure with proposed limit loads. The limit loads are determined from limit analyses based on rectangular wall-thinning and elastic-perfectly-plastic materials using the large geometry change.

  6. S08: investigation and repair of a cracked feeder at Point Lepreau GS

    International Nuclear Information System (INIS)

    A Celovsky, A.; Wright, M.D.; Gendron, T.S.

    1997-01-01

    Early in 1997 investigation of a low level leak in the Point Lepreau GS (PLGS) PHTS revealed that an outlet feeder, S08, was leaking. Ultrasonic inspection, and subsequent failure analysis, revealed that the leak was a consequence of a crack. Given the unusual nature of this event, and current concerns over feeder thinning, a detailed and careful removal and examination procedure was developed. The S08 outlet feeder was removed and shipped to Chalk River Laboratories for examination. The examination confirmed that the failure was a through-wall crack, most likely the consequence of stress corrosion cracking. A critical point of the analysis was to determine how the crack initiated, and subsequently propagated. High residual stresses and possible abnormal loading in conjunction with chemistry environments resulted in the Stress Corrosion Cracking (SCC) of the S08 outlet feeder bend. It is recognized that some of the causative factors implicated in the S08 failure apply to other outlet feeders. In particular, residual stresses in the non-stress-relieved, short-radius cold bent pipes will remain relatively high over the future life of the feeders. However, the risk of CANDU feeder failure by SCC is judged to be extremely low based on the evidence of the inspections carried out to date and the good performance record of feeder pipe in the CANDU industry. The channel was restored to its locked configuration, and the failed section of feeder replaced. (author)

  7. Keratinocytes propagated in serum-free, feeder-free culture conditions fail to form stratified epidermis in a reconstituted skin model.

    Directory of Open Access Journals (Sweden)

    Rebecca Lamb

    Full Text Available Primary human epidermal stem cells isolated from skin tissues and subsequently expanded in tissue culture are used for human therapeutic use to reconstitute skin on patients and to generate artificial skin in culture for academic and commercial research. Classically, epidermal cells, known as keratinocytes, required fibroblast feeder support and serum-containing media for serial propagation. In alignment with global efforts to remove potential animal contaminants, many serum-free, feeder-free culture methods have been developed that support derivation and growth of these cells in 2-dimensional culture. Here we show that keratinocytes grown continually in serum-free and feeder-free conditions were unable to form into a stratified, mature epidermis in a skin equivalent model. This is not due to loss of cell potential as keratinocytes propagated in serum-free, feeder-free conditions retain their ability to form stratified epidermis when re-introduced to classic serum-containing media. Extracellular calcium supplementation failed to improve epidermis development. In contrast, the addition of serum to commercial, growth media developed for serum-free expansion of keratinocytes facilitated 3-dimensional stratification in our skin equivalent model. Moreover, the addition of heat-inactivated serum improved the epidermis structure and thickness, suggesting that serum contains factors that both aid and inhibit stratification.

  8. Human Chorioretinal Layer Thicknesses Measured in Macula-wide, High-Resolution Histologic Sections

    Science.gov (United States)

    Messinger, Jeffrey D.; Sloan, Kenneth R.; Mitra, Arnab; McGwin, Gerald; Spaide, Richard F.

    2011-01-01

    Purpose. To provide a comprehensive description of chorioretinal layer thicknesses in the normal human macula, including two-layer pairs that can produce a combined signal in some optical coherence tomography (OCT) devices (ganglion cell [GCL] and inner plexiform [IPL] layers and outer plexiform [OPL] and outer nuclear [ONL] layers). Methods. In 0.8-μm-thick, macula-wide sections through the foveola of 18 donors (age range, 40–92 years), 21 layers were measured at 25 locations by a trained observer and validated by a second observer. Tissue volume changes were assessed by comparing total retinal thickness in ex vivo OCT and in sections. Results. Median tissue shrinkage was 14.5% overall and 29% in the fovea. Histologic laminar boundaries resembled those in SD-OCT scans, but the shapes of the foveolar OPL and ONL differed. Histologic GCL, IPL, and OPLHenle were thickest at 0.8. to 1, 1.5, and 0.4 mm eccentricity, respectively. ONL was thickest in an inward bulge at the foveal center. At 1 mm eccentricity, GCL, INL, and OPLHenle represented 17.3% to 21.1%, 18.0% to 18.5%, and 14.2% to 16.6% of total retinal thickness, respectively. In donors ≥70 years of age, the RPE and choroid were 17.1% and 29.6% thinner and OPLHenle was 20.8% thicker than in donors macula were generated. Newer OCT systems can separate GCL from IPL and OPLHenle from ONL, with good agreement for the proportion of retinal thickness occupied by OPLHenle in OCT and histology. The thickening of OPLHenle in older eyes may reflect Müller cell hypertrophy associated with rod loss. PMID:21421869

  9. Reconstruction of Hyaline Cartilage Deep Layer Properties in 3-Dimensional Cultures of Human Articular Chondrocytes.

    Science.gov (United States)

    Nanduri, Vibudha; Tattikota, Surendra Mohan; T, Avinash Raj; Sriramagiri, Vijaya Rama Rao; Kantipudi, Suma; Pande, Gopal

    2014-06-01

    Articular cartilage (AC) injuries and malformations are commonly noticed because of trauma or age-related degeneration. Many methods have been adopted for replacing or repairing the damaged tissue. Currently available AC repair methods, in several cases, fail to yield good-quality long-lasting results, perhaps because the reconstructed tissue lacks the cellular and matrix properties seen in hyaline cartilage (HC). To reconstruct HC tissue from 2-dimensional (2D) and 3-dimensional (3D) cultures of AC-derived human chondrocytes that would specifically exhibit the cellular and biochemical properties of the deep layer of HC. Descriptive laboratory study. Two-dimensional cultures of human AC-derived chondrocytes were established in classical medium (CM) and newly defined medium (NDM) and maintained for a period of 6 weeks. These cells were suspended in 2 mm-thick collagen I gels, placed in 24-well culture inserts, and further cultured up to 30 days. Properties of chondrocytes, grown in 2D cultures and the reconstructed 3D cartilage tissue, were studied by optical and scanning electron microscopic techniques, immunohistochemistry, and cartilage-specific gene expression profiling by reverse transcription polymerase chain reaction and were compared with those of the deep layer of native human AC. Two-dimensional chondrocyte cultures grown in NDM, in comparison with those grown in CM, showed more chondrocyte-specific gene activity and matrix properties. The NDM-grown chondrocytes in 3D cultures also showed better reproduction of deep layer properties of HC, as confirmed by microscopic and gene expression analysis. The method used in this study can yield cartilage tissue up to approximately 1.6 cm in diameter and 2 mm in thickness that satisfies the very low cell density and matrix composition properties present in the deep layer of normal HC. This study presents a novel and reproducible method for long-term culture of AC-derived chondrocytes and reconstruction of cartilage

  10. Experience of superconducting current feeders system of SST-1

    International Nuclear Information System (INIS)

    Gupta, N.C.; Garg, A.; Sonara, D.

    2014-01-01

    The superconducting current feeder system for SST-1 which has been installed and commissioned recently along with SST-1, felicitates to energize the SST-1. The CFS consists of ten pairs of 10,000 Ampere (A) rating helium vapor cooled conventional current leads, interconnecting Cu-SC joints, three numbers of cryo-compatible SC feeders ducts, current leads assembly chamber, hydraulic network and three numbers of joint boxes operated at different current rating to charge Toroidal Field and Poloidal Field coils separately. During the last three campaigns, it was possible to achieve a controlled cool down up to 4 K and showed its rated operational performance. Actively cooled liquid nitrogen shield showed temperature profile in the temperature range of 80-85K and the whole system was evacuated up to 6x10 -6 mbar. The measured LHe consumption rates from TF VCCL were 0.3 g/s and 0.35 g/s at zero current and 1 kA respectively. (author)

  11. Identification of distinct layers within the stratified squamous epithelium of the adult human true vocal fold.

    Science.gov (United States)

    Dowdall, Jayme R; Sadow, Peter M; Hartnick, Christopher; Vinarsky, Vladimir; Mou, Hongmei; Zhao, Rui; Song, Phillip C; Franco, Ramon A; Rajagopal, Jayaraj

    2015-09-01

    A precise molecular schema for classifying the different cell types of the normal human vocal fold epithelium is lacking. We hypothesize that the true vocal fold epithelium has a cellular architecture and organization similar to that of other stratified squamous epithelia including the skin, cornea, oral mucosa, and esophagus. In analogy to disorders of the skin and gastrointestinal tract, a molecular definition of the normal cell types within the human vocal fold epithelium and a description of their geometric relationships should serve as a foundation for characterizing cellular changes associated with metaplasia, dysplasia, and cancer. Qualitative study with adult human larynges. Histologic sections of normal human laryngeal tissue were analyzed for morphology (hematoxylin and eosin) and immunohistochemical protein expression profile, including cytokeratins (CK13 and CK14), cornified envelope proteins (involucrin), basal cells (NGFR/p75), and proliferation markers (Ki67). We demonstrated that three distinct cell strata with unique marker profiles are present within the stratified squamous epithelium of the true vocal fold. We used these definitions to establish that cell proliferation is restricted to certain cell types and layers within the epithelium. These distinct cell types are reproducible across five normal adult larynges. We have established that three layers of cells are present within the normal adult stratified squamous epithelium of the true vocal fold. Furthermore, replicating cell populations are largely restricted to the parabasal strata within the epithelium. This delineation of distinct cell populations will facilitate future studies of vocal fold regeneration and cancer. N/A. © 2015 The American Laryngological, Rhinological and Otological Society, Inc.

  12. DYNAMICS OF VIBRATION FEEDERS WITH A NONLINEAR ELASTIC CHARACTERISTIC

    Directory of Open Access Journals (Sweden)

    V. I. Dyrda

    2017-04-01

    Full Text Available Purpose. Subject to the smooth and efficient operation of each production line, is the use of vehicles transporting high specification. It worked well in practice for transporting construction machines, which are used during the vibration. The use of vibration machines requires optimization of their operation modes. In the form of elastic link in them are increasingly using rubber-metallic elements, which are characterized by nonlinear damping properties. So it is necessary to search for new, more modern, methods of calculation of dynamic characteristics of the vibration machines on the properties of rubber as a cushioning material. Methodology. The dynamics of vibration machine that is as elastic rubber block units and buffer shock absorbers limiting the amplitude of the vibrations of the working body. The method of determining amplitude-frequency characteristics of the vibrating feeder is based on the principle of Voltaire, who in the calculations of the damping properties of the dampers will allow for elastic-hereditary properties of rubber. When adjusting the basic dynamic stiffness of the elastic ties and vibratory buffers, using the principle of heredity rubber properties, determine the dependence of the amplitude of the working body of the machine vibrations. This method is called integro-operator using the fractional-exponential kernels of relaxation. Findings. Using the derived formula for determining the amplitude of the resonance curve is constructed one-mass nonlinear system. It is established that the use of the proposed method of calculation will provide a sufficiently complete description of the damping parameters of rubber-metallic elements and at the same time be an effective means of calculating the amplitude-frequency characteristics of nonlinear vibration systems. Originality. The authors improved method of determining damping characteristics of rubber-metallic elements and the amplitude-frequency characteristics of nonlinear

  13. Response of deposit-feeders to exclusion of epibenthic predators in a Mediterranean intertidal flat

    NARCIS (Netherlands)

    Como, S.; Rossi, F.; Lardicci, C.

    2004-01-01

    Deposit-feeders are common components of macrofaunal assemblages in intertidal soft sediments. Predation has been considered to have a central role in affecting their distribution and population dynamics. This study investigates the effect of epibenthic predators on deposit-feeders, inhabiting the

  14. harmonic load modeling: a case study of 33 kv abuja steel mill feeder

    African Journals Online (AJOL)

    HOD

    techniques are adopted. This paper studied the harmonic orders of the 33 kV Abuja Steel Feeder modeled as a ... (ETAP) software package was deployed to perform Discrete Fast Transform (DFT) while the input ... and documented in research and development articles ... network with 33kV Abuja Steel feeder as case study.

  15. Final report on the evolution of supporting conditions for the feeders of 500 MWe PHWR

    International Nuclear Information System (INIS)

    Mishra, Rajesh; Soni, R.S.; Kushawaha, H.S.; Mahajan, S.C.; Kakodkar, A.; Hariprasad, K.

    1994-01-01

    This report deals with the evolution of generic supporting conditions for the feeders of 500 MWe PHWR based on the analysis and qualification of a few representative feeders. There are 196 different feeder pipe configurations for a total of 748 feeders. The present analysis was aimed at evolving a generalised supporting criteria based on the analysis of some representative feeders. The analysis was carried out for various loadings viz. pressure, temperature, dead weight, operating basis earthquake (OBE), safe shutdown earthquake (SSE) and creep loadings. The analysis for OBE and SSE loadings were carried out using response spectrum method. The effect of spacers between various feeders was modelled using higher damping values than those prescribed in ASME code. Based on the above analyses, generic supporting arrangements for the feeders of various groups have been finalized. This report gives details about the mathematical modelling, the analysis approach, the optimised supporting criteria, finalization of grouping and fixing of boundaries between various groups of feeders. (author). 34 refs., 51 figs., 69 tabs

  16. Development of I and C system for the coal feeder of coal firing plant

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Teak Soo; Park, Chan Ho [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center

    1996-12-31

    KECC(Kepco Coal Feeder Control System) receives coal weight, conveyor speed and boiler demand signals. It controls coal flow by generating speed signal of feeder which conveys coal in hopper to pulverizer, displaying measured coal quantity and providing local auto and manual manipulator (author). 33 figs.

  17. Evaluation of options for life cycle management of feeder cracking at the Point Lepreau Generating Station

    International Nuclear Information System (INIS)

    Gendron, T.S.; Slade, J.P.

    2003-01-01

    The CANDU industry has a predictive capability for most Heat Transport System (HTS) degradation issues that allows utilities to apply cost-effective maintenance programs. The standard approach for maintenance programs is focussed inspection and planned replacement. Some examples of degradation issues with deterministic failure rates are feeder thinning, and pressure tube elongation and deuterium ingress. However, the cracking observed in Point Lepreau Generating Station (PLGS) outlet feeder first bends is one notable exception to this behaviour. A predictive capability for feeder cracking does not currently exist for several reasons. First, the mechanism of feeder cracking, stress corrosion cracking (SCC), has to some degree a random nature. Second, although a probable environment causing cracking has been identified, the precise stress and environmental conditions for feeder crack initiation and propagation have not been defined. Finally, the very low incidence of feeder cracking observed to-date (four, all at PLGS) precludes a probabilistic or statistical prediction of failure rate. Generally, utilities select a Life Cycle Management Plan that ensures safe operation and has the lowest Net Present Value cost. In preparing a Feeder Life Cycle Management Plan, New Brunswick Power (NBP) has recognized that the Net Present Value cost is very sensitive to failure rate. Since the failure rate for feeder cracking is not well defined, the following three scenarios were considered to bound the probability of future failures at PLGS. (author)

  18. Feeder cells support the culture of induced pluripotent stem cells even after chemical fixation.

    Directory of Open Access Journals (Sweden)

    Xiao-Shan Yue

    Full Text Available Chemically fixed mouse embryonic fibroblasts (MEFs, instead of live feeder cells, were applied to the maintenance of mouse induced pluripotent stem (miPS cells. Formaldehyde and glutaraldehyde were used for chemical fixation. The chemically fixed MEF feeders maintained the pluripotency of miPS cells, as well as their undifferentiated state. Furthermore, the chemically fixed MEF feeders were reused several times without affecting their functions. These results indicate that chemical fixation can be applied to modify biological feeders chemically, without losing their original functions. Chemically fixed MEF feeders will be applicable to other stem cell cultures as a reusable extracellular matrix candidate that can be preserved on a long-term basis.

  19. Preliminary analysis of accident in SST-1 current feeder system

    International Nuclear Information System (INIS)

    Roy, Swati; Kanabar, Deven; Garg, Atul; Singh, Amit; Tanna, Vipul; Prasad, Upendra; Srinivasan, R.

    2017-01-01

    Steady-state Tokamak-1 (SST-1) has 16 superconducting Toroidal field (TF) and 9 superconducting poloidal field (PF) coils rated for 10kA DC. All the TF are connected in series and are operated in DC condition whereas PF coils are individually operated in pulse mode during SST-1 campaigns. SST-1 current feeder system (CFS) houses 9 pairs of PF current leads and 1 pair of TF current leads. During past SST-1 campaign, there were arcing incidents within SST-1 CFS chamber which caused significant damage to PF superconducting current leads as well as its Helium cooling lines of the current leads. This paper brings out the preliminary analysis of the mentioned arcing incident, possible reasons and its investigation thereby laying out the sequence of events. From this analysis and observations, various measures to avoid such arcing incidents have also been proposed. (author)

  20. Microplastic in a macro filter feeder: Humpback whale Megaptera novaeangliae.

    Science.gov (United States)

    Besseling, E; Foekema, E M; Van Franeker, J A; Leopold, M F; Kühn, S; Bravo Rebolledo, E L; Heße, E; Mielke, L; IJzer, J; Kamminga, P; Koelmans, A A

    2015-06-15

    Marine filter feeders are exposed to microplastic because of their selection of small particles as food source. Baleen whales feed by filtering small particles from large water volumes. Macroplastic was found in baleen whales before. This study is the first to show the presence of microplastic in intestines of a baleen whale (Megaptera novaeangliae). Contents of its gastrointestinal tract were sieved, dissolved in 10% potassium hydroxide and washed. From the remaining dried material, potential synthetic polymer particles were selected based on density and appearance, and analysed by Fourier transform infrared (FTIR) spectroscopy. Several polymer types (polyethylene, polypropylene, polyvinylchloride, polyethylene terephthalate, nylon) were found, in varying particle shapes: sheets, fragments and threads with a size of 1mm to 17cm. This diversity in polymer types and particle shapes, can be interpreted as a representation of the varying characteristics of marine plastic and the unselective way of ingestion by M. novaeangliae. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Development of an extruder-feeder biomass direct liquefaction process

    Energy Technology Data Exchange (ETDEWEB)

    White, D.H.; Wolf, D. (Arizona Univ., Tucson, AZ (United States). Dept. of Chemical Engineering)

    1991-10-01

    As an abundant, renewable, domestic energy resource, biomass could help the United States reduce its dependence on imported oil. Biomass is the only renewable energy technology capable of addressing the national need for liquid transportation fuels. Thus, there is an incentive to develop economic conversion processes for converting biomass, including wood, into liquid fuels. Through research sponsored by the US DOE's Biomass Thermochemical Conversion Program, the University of Arizona has developed a unique biomass direct liquefaction system. The system features a modified single-screw extruder capable of pumping solid slurries containing as high as 60 wt% wood flour in wood oil derived vacuum bottoms at pressures up to 3000 psi. The extruder-feeder has been integrated with a unique reactor by the University to form a system which offers potential for improving high pressure biomass direct liquefaction technology. The extruder-feeder acts simultaneously as both a feed preheater and a pumping device for injecting wood slurries into a high pressure reactor in the biomass liquefaction process. An experimental facility was constructed and following shakedown operations, wood crude oil was produced by mid-1985. By July 1988, a total of 57 experimental continuous biomass liquefaction runs were made using White Birch wood feedstock. Good operability was achieved at slurry feed rates up to 30 lb/hr, reactor pressures from 800 to 3000 psi and temperatures from 350{degree}C to 430{degree}C under conditions covering a range of carbon monoxide feed rates and sodium carbonate catalyst addition. Crude wood oils containing as little as 6--10 wt% residual oxygen were produced. 38 refs., 82 figs., 26 tabs.

  2. Nitrogen fixed by cyanobacteria is utilized by deposit-feeders.

    Science.gov (United States)

    Karlson, Agnes M L; Gorokhova, Elena; Elmgren, Ragnar

    2014-01-01

    Benthic communities below the photic zone depend for food on allochthonous organic matter derived from seasonal phytoplankton blooms. In the Baltic Sea, the spring diatom bloom is considered the most important input of organic matter, whereas the contribution of the summer bloom dominated by diazotrophic cyanobacteria is less understood. The possible increase in cyanobacteria blooms as a consequence of eutrophication and climate change calls for evaluation of cyanobacteria effects on benthic community functioning and productivity. Here, we examine utilization of cyanobacterial nitrogen by deposit-feeding benthic macrofauna following a cyanobacteria bloom at three stations during two consecutive years and link these changes to isotopic niche and variations in body condition (assayed as C:N ratio) of the animals. Since nitrogen-fixing cyanobacteria have δ(15)N close to -2‰, we expected the δ(15)N in the deposit-feeders to decrease after the bloom if their assimilation of cyanobacteria-derived nitrogen was substantial. We also expected the settled cyanobacteria with their associated microheterotrophic community and relatively high nitrogen content to increase the isotopic niche area, trophic diversity and dietary divergence between individuals (estimated as the nearest neighbour distance) in the benthic fauna after the bloom. The three surface-feeding species (Monoporeia affinis, Macoma balthica and Marenzelleria arctia) showed significantly lower δ(15)N values after the bloom, while the sub-surface feeder Pontoporeia femorata did not. The effect of the bloom on isotopic niche varied greatly between stations; populations which increased niche area after the bloom had better body condition than populations with reduced niche, regardless of species. Thus, cyanobacterial nitrogen is efficiently integrated into the benthic food webs in the Baltic, with likely consequences for their functioning, secondary production, transfer efficiency, trophic interactions, and

  3. Nitrogen fixed by cyanobacteria is utilized by deposit-feeders.

    Directory of Open Access Journals (Sweden)

    Agnes M L Karlson

    Full Text Available Benthic communities below the photic zone depend for food on allochthonous organic matter derived from seasonal phytoplankton blooms. In the Baltic Sea, the spring diatom bloom is considered the most important input of organic matter, whereas the contribution of the summer bloom dominated by diazotrophic cyanobacteria is less understood. The possible increase in cyanobacteria blooms as a consequence of eutrophication and climate change calls for evaluation of cyanobacteria effects on benthic community functioning and productivity. Here, we examine utilization of cyanobacterial nitrogen by deposit-feeding benthic macrofauna following a cyanobacteria bloom at three stations during two consecutive years and link these changes to isotopic niche and variations in body condition (assayed as C:N ratio of the animals. Since nitrogen-fixing cyanobacteria have δ(15N close to -2‰, we expected the δ(15N in the deposit-feeders to decrease after the bloom if their assimilation of cyanobacteria-derived nitrogen was substantial. We also expected the settled cyanobacteria with their associated microheterotrophic community and relatively high nitrogen content to increase the isotopic niche area, trophic diversity and dietary divergence between individuals (estimated as the nearest neighbour distance in the benthic fauna after the bloom. The three surface-feeding species (Monoporeia affinis, Macoma balthica and Marenzelleria arctia showed significantly lower δ(15N values after the bloom, while the sub-surface feeder Pontoporeia femorata did not. The effect of the bloom on isotopic niche varied greatly between stations; populations which increased niche area after the bloom had better body condition than populations with reduced niche, regardless of species. Thus, cyanobacterial nitrogen is efficiently integrated into the benthic food webs in the Baltic, with likely consequences for their functioning, secondary production, transfer efficiency, trophic

  4. A Feeder-Bus Dispatch Planning Model for Emergency Evacuation in Urban Rail Transit Corridors

    Science.gov (United States)

    Wang, Yun; Yan, Xuedong; Zhou, Yu; Zhang, Wenyi

    2016-01-01

    The mobility of modern metropolises strongly relies on urban rail transit (URT) systems, and such a heavy dependence causes that even minor service interruptions would make the URT systems unsustainable. This study aims at optimally dispatching the ground feeder-bus to coordinate with the urban rails’ operation for eliminating the effect of unexpected service interruptions in URT corridors. A feeder-bus dispatch planning model was proposed for the collaborative optimization of URT and feeder-bus cooperation under emergency situations and minimizing the total evacuation cost of the feeder-buses. To solve the model, a concept of dummy feeder-bus system is proposed to transform the non-linear model into traditional linear programming (ILP) model, i.e., traditional transportation problem. The case study of Line #2 of Nanjing URT in China was adopted to illustrate the model application and sensitivity analyses of the key variables. The modeling results show that as the evacuation time window increases, the total evacuation cost as well as the number of dispatched feeder-buses decrease, and the dispatched feeder-buses need operate for more times along the feeder-bus line. The number of dispatched feeder-buses does not show an obvious change with the increase of parking spot capacity and time window, indicating that simply increasing the parking spot capacity would cause huge waste for the emergent bus utilization. When the unbalanced evacuation demand exists between stations, the more feeder-buses are needed. The method of this study will contribute to improving transportation emergency management and resource allocation for URT systems. PMID:27676179

  5. Fluorine uptake into the human tooth from a thin layer of F-releasing material

    International Nuclear Information System (INIS)

    Yamamoto, H.; Nomachi, M.; Yasuda, K.; Iwami, Y.; Ebisu, S.; Komatsu, H.; Sakai, T.; Kamiya, T.

    2007-01-01

    Using the proton induced gamma-ray emission (PIGE) method (TIARA, Japan), we have studied fluorine (F) distribution in the human tooth under various conditions. Here, we report F uptake into the human tooth from a thin layer of F-releasing low viscous resin (FLVR). Crowns of human teeth were horizontally cut and the dentin of the cut surface was first covered with four kinds of FLVR (FL-Bond, Reactmer Bond, Xeno Bond, and Protect Liner F; thickness, 50-150 μm) according to the manufacturers' instructions. Non-F-releasing and F-releasing filling resins were also hardened, on the cut surfaces of crowns covered with four kinds of FLVR thin layers. The type of the non-F-releasing filling materials used was LITE FIL IIP: G1-A (FL-Bond and LITE FIL IIP), G2-A (Reactmer Bond and LITE FIL IIP), G3-A (Xeno Bond and LITE FIL IIP), and G4-A (Protect Liner F and LITE FIL IIP). The types of F-releasing filling materials used were G1-B (FL-Bond and Beautifil), G2-B (Reactmer Bond and Reactmer Paste), G3-B (Xeno Bond and Xeno CF Paste), and G4-B (Protect Liner F and Teethmate F-1). Treatment and measurements of specimens were the same as previously reported [H. Yamamoto, M. Nomahci, K. Yasuda, Y. Iwami, S. Ebisu, N. Yamamoto, T. Sakai, T. Kamiya, Nucl. Instr. and Meth. B 210 (2003) 388]. F uptake from specimens following one month of application was estimated from 2-D maps. F penetration was observed in all teeth of G1-A-G4-A groups. The maximum values of F concentration in each tooth and F penetration depth were larger for larger F concentrations in FLVR. FLVR was useful for the F uptake into the tooth, and the F distribution near the thin layer of FLVR depended on the materials used. Between G1-A and G1-B or G4-A and G4-B, the F uptake was significantly different. We were able to obtain fundamental data, which were useful for the analysis of F transportation relating to prevention of caries

  6. Fluorine uptake into the human tooth from a thin layer of F-releasing material

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan)]. E-mail: yhiroko@dent.osaka-u.ac.jp; Nomachi, M. [Graduate School of Science, Osaka University, Toyonaka, Osaka, 560-0043 (Japan); Yasuda, K. [Wakasa Wan Energy Research Center, Tsuruga, Fukui, 914-0192 (Japan); Iwami, Y. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan); Ebisu, S. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan); Komatsu, H. [Graduate School of Dental Medicine, Hokkaido University, Sapporo, Hokkaido, 060-8585 (Japan); Sakai, T. [Advanced Radiation Technology Center, JAERI, Takasaki, Gunma, 370-1292 (Japan); Kamiya, T. [Advanced Radiation Technology Center, JAERI, Takasaki, Gunma, 370-1292 (Japan)

    2007-07-15

    Using the proton induced gamma-ray emission (PIGE) method (TIARA, Japan), we have studied fluorine (F) distribution in the human tooth under various conditions. Here, we report F uptake into the human tooth from a thin layer of F-releasing low viscous resin (FLVR). Crowns of human teeth were horizontally cut and the dentin of the cut surface was first covered with four kinds of FLVR (FL-Bond, Reactmer Bond, Xeno Bond, and Protect Liner F; thickness, 50-150 {mu}m) according to the manufacturers' instructions. Non-F-releasing and F-releasing filling resins were also hardened, on the cut surfaces of crowns covered with four kinds of FLVR thin layers. The type of the non-F-releasing filling materials used was LITE FIL IIP: G1-A (FL-Bond and LITE FIL IIP), G2-A (Reactmer Bond and LITE FIL IIP), G3-A (Xeno Bond and LITE FIL IIP), and G4-A (Protect Liner F and LITE FIL IIP). The types of F-releasing filling materials used were G1-B (FL-Bond and Beautifil), G2-B (Reactmer Bond and Reactmer Paste), G3-B (Xeno Bond and Xeno CF Paste), and G4-B (Protect Liner F and Teethmate F-1). Treatment and measurements of specimens were the same as previously reported [H. Yamamoto, M. Nomahci, K. Yasuda, Y. Iwami, S. Ebisu, N. Yamamoto, T. Sakai, T. Kamiya, Nucl. Instr. and Meth. B 210 (2003) 388]. F uptake from specimens following one month of application was estimated from 2-D maps. F penetration was observed in all teeth of G1-A-G4-A groups. The maximum values of F concentration in each tooth and F penetration depth were larger for larger F concentrations in FLVR. FLVR was useful for the F uptake into the tooth, and the F distribution near the thin layer of FLVR depended on the materials used. Between G1-A and G1-B or G4-A and G4-B, the F uptake was significantly different. We were able to obtain fundamental data, which were useful for the analysis of F transportation relating to prevention of caries.

  7. A Layered Approach for Robust Spatial Virtual Human Pose Reconstruction Using a Still Image

    Directory of Open Access Journals (Sweden)

    Chengyu Guo

    2016-02-01

    Full Text Available Pedestrian detection and human pose estimation are instructive for reconstructing a three-dimensional scenario and for robot navigation, particularly when large amounts of vision data are captured using various data-recording techniques. Using an unrestricted capture scheme, which produces occlusions or breezing, the information describing each part of a human body and the relationship between each part or even different pedestrians must be present in a still image. Using this framework, a multi-layered, spatial, virtual, human pose reconstruction framework is presented in this study to recover any deficient information in planar images. In this framework, a hierarchical parts-based deep model is used to detect body parts by using the available restricted information in a still image and is then combined with spatial Markov random fields to re-estimate the accurate joint positions in the deep network. Then, the planar estimation results are mapped onto a virtual three-dimensional space using multiple constraints to recover any deficient spatial information. The proposed approach can be viewed as a general pre-processing method to guide the generation of continuous, three-dimensional motion data. The experiment results of this study are used to describe the effectiveness and usability of the proposed approach.

  8. Human convective boundary layer and its interaction with room ventilation flow.

    Science.gov (United States)

    Licina, D; Melikov, A; Sekhar, C; Tham, K W

    2015-02-01

    This study investigates the interaction between the human convective boundary layer (CBL) and uniform airflow with different velocity and from different directions. Human body is resembled by a thermal manikin with complex body shape and surface temperature distribution as the skin temperature of an average person. Particle image velocimetry (PIV) and pseudocolor visualization (PCV) are applied to identify the flow around the manikin's body. The findings show that the direction and magnitude of the surrounding airflows considerably influence the airflow distribution around the human body. Downward flow with velocity of 0.175 m/s does not influence the convective flow in the breathing zone, while flow at 0.30 m/s collides with the CBL at the nose level reducing the peak velocity from 0.185 to 0.10 m/s. Transverse horizontal flow disturbs the CBL at the breathing zone even at 0.175 m/s. A sitting manikin exposed to airflow from below with velocity of 0.30 and 0.425 m/s assisting the CBL reduces the peak velocity in the breathing zone and changes the flow pattern around the body, compared to the assisting flow of 0.175 m/s or quiescent conditions. In this case, the airflow interaction is strongly affected by the presence of the chair. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  9. Human embryonic stem cells and microenvironment

    Directory of Open Access Journals (Sweden)

    Banu İskender

    2014-09-01

    Full Text Available Human embryonic stem cells (hESCs possess a great potential in the field of regenerative medicine by their virtue of pluripotent potential with indefinite proliferation capabilities. They can self renew themselves and differentiate into three embryonic germ layers. Although they are conventionally grown on mitotically inactivated mouse feeder cells, there are in vitro culture systems utilizing feeder cells of human origin in order to prevent cross-species contamination. Recently established in vitro culture systems suggested that direct interaction with feeder cells is not necessary but rather attachment to a substrate is required to ensure long-term, efficient hESC culture in vitro. This substrate is usually composed of a mixture of extracellular matrix components representing in vivo natural niche. In hESC biology, the mechanism of interaction of hESCs with extracellular matrix molecules remained insufficiently explored area of research due to their transient nature of interaction with the in vivo niche. However, an in vitro culture system established using extracellular matrix molecules may provide a safer alternative to culture systems with feeder cells while paving the way to Good Manufacturing Practice-GMP production of hESCs for therapeutic purposes. Therefore, it is essential to study the interaction of extracellular matrix molecules with hESCs in order to standardize in vitro culture systems for large-scale production of hESCs in a less labor-intensive way. This would not only provide valuable information regarding the mechanisms that control pluripotency but also serve to dissect the molecular signaling pathways of directed differentiation for prospective therapeutic applications in the future. J Clin Exp Invest 2014; 5 (3: 486-495

  10. Measurements of local mass transfer coefficient of Flow Accelerated Corrosion at feeder outlet pipes in CANDU using Plaster of Paris method

    International Nuclear Information System (INIS)

    Hyuk Kwon; Dong Un Seo; Goon-Cherl Park

    2005-01-01

    Full text of publication follows: Flow Accelerated Corrosion (FAC) is a corrosion mechanism that results in wall thinning in piping systems and components. FAC on carbon steels in pure water has occurred in a number of industry and power plant. A pipe wall thinning due to the FAC at nuclear power plant is just reported in confined to carbon steel pipe on the secondary system which does not equip a radioactive component. Recently, at Canadian Deuterium Uranium type reactor, it is reported that the feeder lines suffer the wall thinning on the primary system to equip 380 feeder pipes. Differently from the fast FAC rate of the secondary system on PWR, FAC rate of feeder pipes on CANDU is not more than the 0.2 mm/year. Although the FAC rate of feeder pipe is relatively slow, the narrow thickness margin of 2.6089 mm is endangered sufficiently by only the slow FAC rate. The FAC is governed by the mass transfer coefficient which is determined by the flow field. To well predict the FAC rate, mass transfer coefficient should be well measured or calculated. New measurement method of mass transfer coefficient is developed to obtain the coefficient for the complex shape like feeder pipe. The method evaluated the naphthalene sublimation method to apply it under the water flow. The naphthalene sublimation method can be used to study mass and heat transfer with confidence for a variety of applications, but with certain restrictions. At present, Plaster of paris method can modified the sublimation method to overcome the restrictions. This method is particularly useful in complex flows on geometries and for flows with large gradients in wall transport rate. The test specimen can be easily prepared by several methods, including dipping, machining, spraying, and casting. The local transfer coefficients can be determined with high accuracy and in detail by automated measurement systems that eliminate most human errors during the measurement process. To evaluate the method, the

  11. Layer specific tensile testing of human arteries at the Austrian SAXS beamline at ELETTRA

    International Nuclear Information System (INIS)

    Schmid, F.; Rappolt, M.; Amenitsch, H.; Laggner, P.; Schulze-Bauer, C.A.; Sommer, G.; Holzapfel, G.A.; Regitnig, P.

    2005-01-01

    Full text: The collagen diffraction patterns of human aortas under uniaxial tensile test conditions have been investigated by synchrotron small angle x-ray diffraction. Using a recently designed tensile testing device, the orientation and d-spacing of the collagen fibers in the major arterial layers have been measured in situ under physiological conditions, together with the macroscopic force and sample stretching. The results show a direct relation between the orientation/extension of the collagen fibers on the nanoscopic level and the macroscopic stress and strain. This is attributed first to a straightening, second to a reorientation of the collagen fibers, and third to an uptaKEX of the increasing loads by the collagen fibers. (author)

  12. Impacting effects of seismic loading in feeder pipes of PHWR power plants

    International Nuclear Information System (INIS)

    Kumar, R.

    1996-01-01

    The core of a pressurized heavy water reactor (PHWR) consists of a large number of fuel channels. These fuel channels are connected to the feeder pipes through which the heavy water flows and transports heat from the reactor core to the steam generators. The feeder pipes are several hundreds in number. They run close to each other with small gaps and have several bends. Thus they represent a complex piping system. Under seismic loading, the adjacent feeder pipes may impact each other. In this paper a simplified procedure has been established to assess such impacting effects. The results of the proposed analysis include bending moment and impact force, which provide the stresses due to impacting effects. These results are plotted in nondimensional form so that they could be utilized for any set of feeder pipes. The procedure used for studying the impacting effects includes seismic analysis of individual feeder pipes without impacting effects, selection of pipes for impact analysis, and estimating their maximum impact velocity. Based on the static and dynamic characteristics of the selected feeder pipes, the maximum bending moment, impact force, and stresses are obtained. The results of this study are useful for quick evaluation of the impacting effects in feeder pipes

  13. A novel method for decomposing electricity feeder load into elementary profiles from customer information

    International Nuclear Information System (INIS)

    Gerossier, Alexis; Barbier, Thibaut; Girard, Robin

    2017-01-01

    Highlights: •Use of aggregated electricity load profiles and customer description at feeder level. •Statistical recovery of elementary load profiles with customer categorization. •Generation of load demand profiles for unknown feeders and new local areas. •Relevancy of the different categorizations. -- Abstract: To plan a distribution grid involves making a long-term forecast of sub-hourly demand, which requires modeling the demand and its dynamics with aggregated measurement data. Distribution system operators (DSOs) have been recording electricity sub-hourly demand delivered by their medium-voltage feeders (around 1000—10,000 customers) for several years. Demand profiles differ widely among the various considered feeders. This is partly due to the varying mix of customer categories from one feeder to another. To overcome this issue, elementary demand profiles are often associated with customer categories and then combined according to a mix description. This paper presents a novel method to estimate elementary profiles that only requires several feeder demand curves and a description of customers. The method relies on a statistical blind source model and a new estimation procedure based on the augmented Lagrangian method. The use of feeders to estimate elementary profiles means that measurements are fully representative and continuously updated. We illustrate the proposed method through a case study comprising around 1000 feeder demand curves operated by the main French DSO Enedis. We propose an application o that uses the obtained profiles to evaluate the contribution of any set of new customers to a feeder peak load. We show that profiles enable a simulation of new unmeasured areas with errors of around 20%. We also show how our method can be used to evaluate the relevancy of different customer categorizations.

  14. Anoxic monimolimnia: Nutrients devious feeders or bombs ready to explode?

    Science.gov (United States)

    Gianni, Areti; Zacharias, Ierotheos

    2015-04-01

    Coastal regions are under strong human influence and its environmental impact is reflected into their water quality. Oligotrophic estuaries and coastal systems have changed in mesotrophic and/or eutrophic, shown an increase in toxic algal blooms, hypoxic/anoxic events, and massive mortalities of many aquatic and benthic organisms. In strongly stratified and productive water basins, bottom water dissolved oxygen is depleted due to the excessive organic matter decomposition in these depths. Distribution and recycling of nutrients in their water column is inextricably dependent on oxygenation and redox conditions. Bottom water anoxia accelerates PO43-, NH4+ and H2S recycling and accumulation from organic matter decomposition. The anoxic, H2S, PO43- and NH4+ rich bottom water constitutes a toxic layer, threatening the balance of the entire ecosystem. In permanently stratified water basins, storm events could result in stratification destruction and water column total mixing. The turnover brings large amounts of H2S to the surface resulting in low levels of oxygen and massive fish kills. PO43- and NH4+ are released to the interface and surface waters promoting algal blooms. Μore organic matter is produced fueling anoxia. The arising question is, whether the balance of an anoxic water ecosystem is under the threat of its hypolimnetic nutrient and sulfide load, only in the case of storm events and water column total mixing. In polymictic water basins it is clear that the accumulated, in the bottom layer, nutrients will supply surface waters, after the pycnocline overturn. Besides this mechanism of basins' water quality degradation is nowadays recognized as one of the biggest obstacles in eutrophic environments management and restoration efforts. The role of internal load, in permanently stratified water basins, is not so clear. In the present study the impact of storm events on water column stability and bottom water anoxia of meromictic coastal basins, is investigated

  15. Tactile Evaluation Feedback System for Multi-Layered Structure Inspired by Human Tactile Perception Mechanism

    Directory of Open Access Journals (Sweden)

    Iza Husna Mohamad Hashim

    2017-11-01

    Full Text Available Tactile sensation is one type of valuable feedback in evaluating a product. Conventionally, sensory evaluation is used to get direct subjective responses from the consumers, in order to improve the product’s quality. However, this method is a time-consuming and costly process. Therefore, this paper proposes a novel tactile evaluation system that can give tactile feedback from a sensor’s output. The main concept of this system is hierarchically layering the tactile sensation, which is inspired by the flow of human perception. The tactile sensation is classified from low-order of tactile sensation (LTS to high-order of tactile sensation (HTS, and also to preference. Here, LTS will be correlated with physical measures. Furthermore, the physical measures that are used to correlate with LTS are selected based on four main aspects of haptic information (roughness, compliance, coldness, and slipperiness, which are perceived through human tactile sensors. By using statistical analysis, the correlation between each hierarchy was obtained, and the preference was derived in terms of physical measures. A verification test was conducted by using unknown samples to determine the reliability of the system. The results showed that the system developed was capable of estimating preference with an accuracy of approximately 80%.

  16. Tactile Evaluation Feedback System for Multi-Layered Structure Inspired by Human Tactile Perception Mechanism.

    Science.gov (United States)

    Hashim, Iza Husna Mohamad; Kumamoto, Shogo; Takemura, Kenjiro; Maeno, Takashi; Okuda, Shin; Mori, Yukio

    2017-11-11

    Tactile sensation is one type of valuable feedback in evaluating a product. Conventionally, sensory evaluation is used to get direct subjective responses from the consumers, in order to improve the product's quality. However, this method is a time-consuming and costly process. Therefore, this paper proposes a novel tactile evaluation system that can give tactile feedback from a sensor's output. The main concept of this system is hierarchically layering the tactile sensation, which is inspired by the flow of human perception. The tactile sensation is classified from low-order of tactile sensation (LTS) to high-order of tactile sensation (HTS), and also to preference. Here, LTS will be correlated with physical measures. Furthermore, the physical measures that are used to correlate with LTS are selected based on four main aspects of haptic information (roughness, compliance, coldness, and slipperiness), which are perceived through human tactile sensors. By using statistical analysis, the correlation between each hierarchy was obtained, and the preference was derived in terms of physical measures. A verification test was conducted by using unknown samples to determine the reliability of the system. The results showed that the system developed was capable of estimating preference with an accuracy of approximately 80%.

  17. Caries induced cytokine network in the odontoblast layer of human teeth

    Directory of Open Access Journals (Sweden)

    Horst Jeremy A

    2011-01-01

    Full Text Available Abstract Background Immunologic responses of the tooth to caries begin with odontoblasts recognizing carious bacteria. Inflammatory propagation eventually leads to tooth pulp necrosis and danger to health. The present study aims to determine cytokine gene expression profiles generated within human teeth in response to dental caries in vivo and to build a mechanistic model of these responses and the downstream signaling network. Results We demonstrate profound differential up-regulation of inflammatory genes in the odontoblast layer (ODL in human teeth with caries in vivo, while the pulp remains largely unchanged. Interleukins, chemokines, and all tested receptors thereof were differentially up-regulated in ODL of carious teeth, well over one hundred-fold for 35 of 84 genes. By interrogating reconstructed protein interaction networks corresponding to the differentially up-regulated genes, we develop the hypothesis that pro-inflammatory cytokines highly expressed in ODL of carious teeth, IL-1β, IL-1α, and TNF-α, carry the converged inflammatory signal. We show that IL1β amplifies antimicrobial peptide production in odontoblasts in vitro 100-fold more than lipopolysaccharide, in a manner matching subsequent in vivo measurements. Conclusions Our data suggest that ODL amplifies bacterial signals dramatically by self-feedback cytokine-chemokine signal-receptor cycling, and signal convergence through IL1R1 and possibly others, to increase defensive capacity including antimicrobial peptide production to protect the tooth and contain the battle against carious bacteria within the dentin.

  18. Improvement of Local Voltage in Feeders with Photovoltaic using Electric Vehicles

    DEFF Research Database (Denmark)

    Marra, Francesco; Yang, Guangya; Fawzy, Y. T.

    2013-01-01

    In low-voltage (LV) feeders with high penetration of photovoltaic (PV), a major issue to be solved is voltage rise due to the active power injection. If no measures are taken, this may lead to generation’s interruptions and to the malfunctioning of domestic appliances due to non-standard voltage...... profiles. This paper proposes a storage strategy to alleviate voltage rise in feeders with PV, using coordinated electric vehicle (EV) load as the storage solution. The voltage support strategy is easy to implement practically and it is demonstrated on a test feeder emulating a household with roof...

  19. Minimal incorporation of Deepwater Horizon oil by estuarine filter feeders

    International Nuclear Information System (INIS)

    Fry, Brian; Anderson, Laurie C.

    2014-01-01

    Highlights: • Oil from the Deepwater Horizon oil spill entered Louisiana bays in mid-2010. • Oil was used minimally (<1%) in diets of mussels and barnacles. • Also, oil did not enhance planktonic respiration rates. • Use of oil carbon was relatively small in these productive estuarine food webs. - Abstract: Natural abundance carbon isotope analyses are sensitive tracers for fates and use of oil in aquatic environments. Use of oil carbon in estuarine food webs should lead to isotope values approaching those of oil itself, −27‰ for stable carbon isotopes reflecting oil origins and −1000‰ for carbon-14 reflecting oil age. To test for transfer of oil from the 2010 Deepwater Horizon spill into estuarine food webs, filter-feeding barnacles (Balanus sp.) and marsh mussels (Geukensia demissa) were collected from Louisiana estuaries near the site of the oil spill. Carbon-14 analyses of these animals from open waters and oiled marshes showed that oil use was <1% and near detection limits estimated at 0.3% oil incorporation. Respiration studies showed no evidence for enhanced microbial activity in bay waters. Results are consistent with low dietary impacts of oil for filter feeders and little overall impact on respiration in the productive Louisiana estuarine systems

  20. Automatic feeder for small fish held in tanks

    Science.gov (United States)

    Joeris, Leonard S.

    1965-01-01

    The Northville (Michigan) Biological Station has been a center for study of the developmental morphology of coregonid fishes. This work requires the production of numerous individual series of lake herring, lake whitefish, and several species of chubs from parent fish of positively known identity. The offspring of individual pairs or groups of fish must be held in individual tanks from the time they hatch until they reach maturity. One of the important problems in this project has been the poor growth of most fish. Though some have grown well, their growth has been less than that of the same species in nature, and a few fish from each hatch have grown very slowly. Irregularity of feeding may contribute to the slow growth of laboratory fish. The hatchery caretaker feeds them several times during his 8-hour workday, but they must go without food during the remaining 16 hours. The high metabolic rate of small fish, however, appears to make them strongly inclined toward almost continual feeding. Belief that greater, more regular food consumption would result from a mechanical feeder providing a continuous supply of food over a longer period of the day led to development of the equipment described in this paper.

  1. Decision Support for Optimal Repositioning of Containers in a Feeder System

    Directory of Open Access Journals (Sweden)

    Danijela Tuljak-Suban

    2008-03-01

    Full Text Available The transport of empty containers represents a seriousproblem in the fast growing sphere of maritime container transport.The most widespread type of container transport organizationin maritime transport is the hub and spoke mode, whichenables the transport of a great number of containers via largevessels between hub ports, from where feeder ships transport tosmaller ports that thus gravitate to the central hub port. The articlecontains a detailed analysis of the northern Adriatic portsand the feeder connections with the hub ports of the Mediterranean.A two-level VRPPD (Vehicle Routing Problem withPickup and Delivery problem is modelled on a graph, wherethe transport of full containers is privileged over the transport ofempty containers. This enables the simulation of the feeder systemin the n01them Adriatic, meaning that it shows the ship'soperator the movement programme with minimal transportcosts for the superfluous empty containers in the complex of theregular transports of full containers in the feeder system.

  2. Automatic segmentation of human cortical layer-complexes and architectural areas using diffusion MRI and its validation

    Directory of Open Access Journals (Sweden)

    Matteo Bastiani

    2016-11-01

    Full Text Available Recently, several magnetic resonance imaging contrast mechanisms have been shown to distinguish cortical substructure corresponding to selected cortical layers. Here, we investigate cortical layer and area differentiation by automatized unsupervised clustering of high resolution diffusion MRI data. Several groups of adjacent layers could be distinguished in human primary motor and premotor cortex. We then used the signature of diffusion MRI signals along cortical depth as a criterion to detect area boundaries and find borders at which the signature changes abruptly. We validate our clustering results by histological analysis of the same tissue. These results confirm earlier studies which show that diffusion MRI can probe layer-specific intracortical fiber organization and, moreover, suggests that it contains enough information to automatically classify architecturally distinct cortical areas. We discuss the strengths and weaknesses of the automatic clustering approach and its appeal for MR-based cortical histology.

  3. Demonstration of Market-Based Real-Time Electricity Pricing on a Congested Feeder

    DEFF Research Database (Denmark)

    Larsen, Emil Mahler; Pinson, Pierre; le Ray, Guillaume

    2015-01-01

    Congestion management can delay grid reinforcements needed due to the growth of distributed technologies like photovoltaics and electric vehicles. This paper presents a method of congestion management for low voltage feeders using indirect control from the smart grid demonstration EcoGrid EU, where...... prices to 1900 houses, with a virtual feeder of 28 houses receiving congestion pricing. Simulations are used to calculate the cost from using this congestion management method, while demonstration results indicate that congestion can be managed successfully....

  4. The human periodontal membrane: focusing on the spatial interrelation between the epithelial layer of Malassez, fibers, and innervation

    DEFF Research Database (Denmark)

    Kjaer, Inger; Nolting, Dorrit

    2009-01-01

    OBJECTIVE: The purpose of the present study was to map the spatial interrelation of fibers, peripheral nerves, and epithelial layer of Malassez in human periodontal membrane in areas close to the root surfaces. MATERIAL AND METHODS: Four healthy permanent teeth extracted from four patients during...

  5. Protoporphyrin IX formation and photobleaching in different layers of normal human skin

    DEFF Research Database (Denmark)

    Togsverd-Bo, Katrine; Idorn, Luise W; Philipsen, Peter A

    2012-01-01

    human skin was tape-stripped and incubated with 20% methylaminolevulinate (MAL) or 20% hexylaminolevulinate (HAL) for 3 h. Fluorescence microscopy quantified PpIX accumulation in epidermis, superficial, mid and deep dermis, down to 2 mm. PpIX photobleaching by light-emitting diode (LED, 632 nm, 18......Topical photodynamic therapy (PDT) is used for various skin disorders, and selective targeting of specific skin structures is desirable. The objective was to assess accumulation of PpIX fluorescence and photobleaching within skin layers using different photosensitizers and light sources. Normal...... and 37 J/cm(2)), intense pulsed light (IPL, 500-650 nm, 36 and 72 J/cm(2)) and long-pulsed dye laser (LPDL, 595 nm, 7.5 and 15 J/cm(2)) was measured using fluorescence photography and microscopy. We found higher PpIX fluorescence intensities in epidermis and superficial dermis in HAL-incubated skin than...

  6. Manufacture and test of seismic bellows for ITER magnet feeder

    International Nuclear Information System (INIS)

    Liu, Chen; Lu, Kun; Sheng, Liang; Song, Yuntao; Su, Jinjin; Su, Man; Gung, Chenyu

    2016-01-01

    Highlights: • The design of the double bellows was iterated with the results of analysis based on the Expansion Joint Manufacturers Association (EJMA) standard. • The seismic bellows was tested with cyclic pressurization of the interlayer space to 2 bars absolute pressure for 5 cycles. • 200 cycles of tensile fatigue test with 90 mm of stretching from the nominal design length. • A full tensile test with 315 mm of stretching from its nominal length was conducted. • The prototype bellows was qualified for its leak tightness (less than 1 × 10 −9 Pam 3 /s of helium) at all time during the qualification test. - Abstract: This paper presents the key manufacturing and testing processes of the prototype ITER feeder seismic bellows. The design of the double bellows was iterated with the results of analysis based on the Expansion Joint Manufacturers Association (EJMA) standard. Each inner and outer bellows was supported in dedicated molds and formed by a hydraulic pressure machine rated at 800 tons. The double bellows were constructed by welding individual collars to the end flanges. The seismic bellows was tested with cyclic pressurization of the interlayer space to 2 bars absolute pressure for 5 cycles. This was followed by 200 cycles of tensile fatigue test with 90 mm of stretching from the nominal design length. After the mechanical fatigue test, a full tensile test with 315 mm of stretching from its nominal length was conducted. Helium leak tests, with the sensitivity of the helium leak detector set to 1 × 10 −9 Pa m 3 /s of helium, were performed at different stages of pressure and mechanical tests. The prototype bellows was qualified for its leak tightness at all time during the qualification test.

  7. Manufacture and test of seismic bellows for ITER magnet feeder

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chen, E-mail: liuchen@ipp.ac.cn [Institute of Plasma Physics Chinese Academy of Sciences, ShuShanhu Road No. 350, Hefei (China); Lu, Kun [Institute of Plasma Physics Chinese Academy of Sciences, ShuShanhu Road No. 350, Hefei (China); Sheng, Liang [AEROSUN-TOLA Expansion Joint Co., Ltd., Jiangjun Road No. 199, Nanjing (China); Song, Yuntao; Su, Jinjin [Institute of Plasma Physics Chinese Academy of Sciences, ShuShanhu Road No. 350, Hefei (China); Su, Man; Gung, Chenyu [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul-lez-Durance (France)

    2016-11-01

    Highlights: • The design of the double bellows was iterated with the results of analysis based on the Expansion Joint Manufacturers Association (EJMA) standard. • The seismic bellows was tested with cyclic pressurization of the interlayer space to 2 bars absolute pressure for 5 cycles. • 200 cycles of tensile fatigue test with 90 mm of stretching from the nominal design length. • A full tensile test with 315 mm of stretching from its nominal length was conducted. • The prototype bellows was qualified for its leak tightness (less than 1 × 10{sup −9} Pam{sup 3}/s of helium) at all time during the qualification test. - Abstract: This paper presents the key manufacturing and testing processes of the prototype ITER feeder seismic bellows. The design of the double bellows was iterated with the results of analysis based on the Expansion Joint Manufacturers Association (EJMA) standard. Each inner and outer bellows was supported in dedicated molds and formed by a hydraulic pressure machine rated at 800 tons. The double bellows were constructed by welding individual collars to the end flanges. The seismic bellows was tested with cyclic pressurization of the interlayer space to 2 bars absolute pressure for 5 cycles. This was followed by 200 cycles of tensile fatigue test with 90 mm of stretching from the nominal design length. After the mechanical fatigue test, a full tensile test with 315 mm of stretching from its nominal length was conducted. Helium leak tests, with the sensitivity of the helium leak detector set to 1 × 10{sup −9} Pa m{sup 3}/s of helium, were performed at different stages of pressure and mechanical tests. The prototype bellows was qualified for its leak tightness at all time during the qualification test.

  8. Changes in thunderstorm characteristics due to feeder cloud merging

    Science.gov (United States)

    Sinkevich, Andrei A.; Krauss, Terrence W.

    2014-06-01

    Cumulus cloud merging is a complex dynamical and microphysical process in which two convective cells merge into a single cell. Previous radar observations and numerical simulations have shown a substantial increase in the maximum area, maximum echo top and maximum reflectivity as a result of the merging process. Although the qualitative aspects of merging have been well documented, the quantitative effects on storm properties remain less defined. Therefore, a statistical assessment of changes in storm characteristics due to merging is of importance. Further investigation into the effects of cloud merging on precipitation flux (Pflux) in a statistical manner provided the motivation for this study in the Asir region of Saudi Arabia. It was confirmed that merging has a strong effect on storm development in this region. The data analysis shows that an increase in the median of the distribution of maximum reflectivity was observed just after merging and was equal to 3.9 dBZ. A detailed analysis of the individual merge cases compared the merged storm Pflux and mass to the sum of the individual Feeder and Storm portions just before merging for each case. The merged storm Pflux increased an average of 106% over the 20-min period after merging, and the mass increased on average 143%. The merged storm clearly became larger and more severe than the sum of the two parts prior to merging. One consequence of this study is that any attempts to evaluate the precipitation enhancement effects of cloud seeding must also include the issue of cloud mergers because merging can have a significant effect on the results.

  9. Unveiling 25 Years of Planetary Urbanization with Remote Sensing: Perspectives from the Global Human Settlement Layer

    Directory of Open Access Journals (Sweden)

    Michele Melchiorri

    2018-05-01

    Full Text Available In the last few decades the magnitude and impacts of planetary urban transformations have become increasingly evident to scientists and policymakers. The ability to understand these processes remained limited in terms of territorial scope and comparative capacity for a long time: data availability and harmonization were among the main constraints. Contemporary technological assets, such as remote sensing and machine learning, allow for analyzing global changes in the settlement process with unprecedented detail. The Global Human Settlement Layer (GHSL project set out to produce detailed datasets to analyze and monitor the spatial footprint of human settlements and their population, which are key indicators for the global policy commitments of the 2030 Development Agenda. In the GHSL, Earth Observation plays a key role in the detection of built-up areas from the Landsat imagery upon which population distribution is modelled. The combination of remote sensing imagery and population modelling allows for generating globally consistent and detailed information about the spatial distribution of built-up areas and population. The GHSL data facilitate a multi-temporal analysis of human settlements with global coverage. The results presented in this article focus on the patterns of development of built-up areas, population and settlements. The article reports about the present status of global urbanization (2015 and its evolution since 1990 by applying to the GHSL the Degree of Urbanisation definition of the European Commission Directorate General for Regional and Urban Policy (DG-Regio and the Statistical Office of the European Communities (EUROSTAT. The analysis portrays urbanization dynamics at a regional level and per country income classes to show disparities and inequalities. This study analyzes how the 6.1 billion urban dwellers are distributed worldwide. Results show the degree of global urbanization (which reached 85% in 2015, the more than 100

  10. Characterization of soil bacterial, archaeal and fungal communities inhabiting archaeological human-impacted layers at Monte Iato settlement (Sicily, Italy).

    Science.gov (United States)

    Siles, José A; Öhlinger, Birgit; Cajthaml, Tomas; Kistler, Erich; Margesin, Rosa

    2018-01-30

    Microbial communities in human-impacted soils of ancient settlements have been proposed to be used as ecofacts (bioindicators) of different ancient anthropogenic activities. In this study, bacterial, archaeal and fungal communities inhabiting soil of three archaic layers, excavated at the archaeological site on Monte Iato (Sicily, Italy) and believed to have been created in a chronological order in archaic times in the context of periodic cultic feasts, were investigated in terms of (i) abundance (phospholipid fatty acid (PLFA) analysis and quantitative PCR)), (ii) carbon(C)-source consumption patterns (Biolog-Ecoplates) and (iii) diversity and community composition (Illumina amplicon sequencing). PLFA analyses demonstrated the existence of living bacteria and fungi in the soil samples of all three layers. The upper layer showed increased levels of organic C, which were not concomitant with an increment in the microbial abundance. In taxonomic terms, the results indicated that bacterial, archaeal and fungal communities were highly diverse, although differences in richness or diversity among the three layers were not detected for any of the communities. However, significantly different microbial C-source utilization patterns and structures of bacterial, archaeal and fungal communities in the three layers confirmed that changing features of soil microbial communities reflect different past human activities.

  11. The fine structure of human germ layers in vivo: clues to the early differentiation of embryonic stem cells in vitro.

    Science.gov (United States)

    Sathananthan, Henry; Selvaraj, Kamala; Clark, Joan

    2011-08-01

    The fine structure of the three germ layers in human ectopic embryos (stage 7) have been documented by digital light and electron microscopy. The formation of ectoderm, endoderm and mesoderm and notochordal cells, and also the extraembryonic membranes, amnion and yolk sac, are imaged. The germ layers give rise to all the cells and tissues of the human body. Possible clues to the early differentiation of embryonic stem cells (ESC) in vitro were obtained, since these events are more or less mimicked in cultures of ESC derived from the inner cell mass of human blastocysts. The findings are discussed with reference to previous studies on the fine structure of ESC using the same technique. Copyright © 2011. Published by Elsevier Ltd.

  12. Advanced feeder-free generation of induced pluripotent stem cells directly from blood cells.

    Science.gov (United States)

    Trokovic, Ras; Weltner, Jere; Nishimura, Ken; Ohtaka, Manami; Nakanishi, Mahito; Salomaa, Veikko; Jalanko, Anu; Otonkoski, Timo; Kyttälä, Aija

    2014-12-01

    Generation of validated human induced pluripotent stem cells (iPSCs) for biobanking is essential for exploring the full potential of iPSCs in disease modeling and drug discovery. Peripheral blood mononuclear cells (PBMCs) are attractive targets for reprogramming, because blood is collected by a routine clinical procedure and is a commonly stored material in biobanks. Generation of iPSCs from blood cells has previously been reported using integrative retroviruses, episomal Sendai viruses, and DNA plasmids. However, most of the published protocols require expansion and/or activation of a specific cell population from PBMCs. We have recently collected a PBMC cohort from the Finnish population containing more than 2,000 subjects. Here we report efficient generation of iPSCs directly from PBMCs in feeder-free conditions in approximately 2 weeks. The produced iPSC clones are pluripotent and transgene-free. Together, these properties make this novel method a powerful tool for large-scale reprogramming of PBMCs and for iPSC biobanking. ©AlphaMed Press.

  13. TOWARDS CONSISTENT MAPPING OF URBAN STRUCTURES – GLOBAL HUMAN SETTLEMENT LAYER AND LOCAL CLIMATE ZONES

    Directory of Open Access Journals (Sweden)

    B. Bechtel

    2016-06-01

    Full Text Available Although more than half of the Earth’s population live in urban areas, we know remarkably little about most cities and what we do know is incomplete (lack of coverage and inconsistent (varying definitions and scale. While there have been considerable advances in the derivation of a global urban mask using satellite information, the complexity of urban structures, the heterogeneity of materials, and the multiplicity of spectral properties have impeded the derivation of universal urban structural types (UST. Further, the variety of UST typologies severely limits the comparability of such studies and although a common and generic description of urban structures is an essential requirement for the universal mapping of urban structures, such a standard scheme is still lacking. More recently, there have been two developments in urban mapping that have the potential for providing a standard approach: the Local Climate Zone (LCZ scheme (used by the World Urban Database and Access Portal Tools project and the Global Human Settlement Layer (GHSL methodology by JRC. In this paper the LCZ scheme and the GHSL LABEL product were compared for selected cities. The comparison between both datasets revealed a good agreement at city and coarse scale, while the contingency at pixel scale was limited due to the mismatch in grid resolution and typology. At a 1 km scale, built-up as well as open and compact classes showed very good agreement in terms of correlation coefficient and mean absolute distance, spatial pattern, and radial distribution as a function of distance from town, which indicates that a decomposition relevant for modelling applications could be derived from both. On the other hand, specific problems were found for both datasets, which are discussed along with their general advantages and disadvantages as a standard for UST classification in urban remote sensing.

  14. Development of a feeder device for logging residue for a drum chipper; Hakkurin syoetoen kehittaeminen energiapuulle

    Energy Technology Data Exchange (ETDEWEB)

    Leinonen, T.; Kemppainen, J P [Oulu Univ. (Finland). Dept. of Mechanical Engineering

    1997-12-01

    The aim of this project is to increase the productivity of a large drum chipper by developing a feeder device to be used especially when chipping logging residue. Logging residue from regeneration areas is the most important reserve of forest biomass for the production of renewable energy in Finland. It is possible ecologically and economically to use about 5 million m{sup 3} of logging residue yearly for energy purposes. Currently both large lorry based chippers and smaller forwarder based chippers are used for chipping logging residue. However even the latest versions of these chippers are not well equipped for chipping logging residue. The ball like shape of residue piles causes blockades, if too large amounts of residue are fed into the chipper. Keeping the material flow even is difficult. In this project a prototype of a feeder device will be designed and manufactured to exactly find out the problems, that occur when feeding logging residue to a chipper. The designed prototype is based on a tubular chassis, which supports a conveyor made of steel plates. Prototype also has a 2,5 m wide feeding table and a feeder roll, which is located above the conveyor just before the chipper opening. Both the conveyor and the feeder roll are powered by hydraulic motors. The maximum feeding force is 20 kN. For research purposes both hydraulic pressure and flow can be adjusted individually for both motors. During 1996 activities included designing and building the prototype feeder device. In 1997 the prototype will be tested to find out possible problems, which need to be cured. After problems are solved and other improvements are made, the feeder device will be installed to an existing chipper and then tested again to determine the productivity of the new feeder device compared to the old unit. (orig.)

  15. Computational fluid dynamics analysis for flow accelerated corrosion in CANDU6 feeder pipes

    International Nuclear Information System (INIS)

    Catana, A.; Pauna, E.; Ioan, M.

    2013-01-01

    CANDU6 plant management over a long time period includes various ageing and degradation mechanisms like FAC manifested mainly at first and second elbow of CANDU6 outlet feeders. FAC take place at all CANDU6 built before 2000 year with feeders made from SA106 grade B low alloy carbon-steel (with chromium at 0.02%). CFD method is used in this paper to investigate the feeder's wall thinning process taking place mainly due local flow conditions in complex 3D geometrical configurations. The 380 outlet feeders grouped in 2.5'' (320) and 2.0'' feeders (60). The objective of this paper is to help, as much as possible, to focus investigation on most probable maximum thinning rate locations through 3D distribution of some TH parameters. Application of CFD methods in CANDU6 nuclear reactors implies the knowledge of real plant operating data like: long term time averaged channel power and mass flow as well as temperature, pressure, pHa etc allowing the optimization and cost reduction of wall thinning monitoring process at CANDU6 nuclear power plants. (authors)

  16. Network Reduction Algorithm for Developing Distribution Feeders for Real-Time Simulators: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Nagarajan, Adarsh; Nelson, Austin; Prabakar, Kumaraguru; Hoke, Andy; Asano, Marc; Ueda, Reid; Nepal, Shaili

    2017-06-15

    As advanced grid-support functions (AGF) become more widely used in grid-connected photovoltaic (PV) inverters, utilities are increasingly interested in their impacts when implemented in the field. These effects can be understood by modeling feeders in real-time systems and testing PV inverters using power hardware-in-the-loop (PHIL) techniques. This paper presents a novel feeder model reduction algorithm using a Monte Carlo method that enables large feeders to be solved and operated on real-time computing platforms. Two Hawaiian Electric feeder models in Synergi Electric's load flow software were converted to reduced order models in OpenDSS, and subsequently implemented in the OPAL-RT real-time digital testing platform. Smart PV inverters were added to the real-time model with AGF responses modeled after characterizing commercially available hardware inverters. Finally, hardware inverters were tested in conjunction with the real-time model using PHIL techniques so that the effects of AGFs on the choice feeders could be analyzed.

  17. Comparing the engineering program feeders from SiF and convention models

    Science.gov (United States)

    Roongruangsri, Warawaran; Moonpa, Niwat; Vuthijumnonk, Janyawat; Sangsuwan, Kampanart

    2018-01-01

    This research aims to compare the relationship between two types of engineering program feeder models within the technical education systems of Rajamangala University of Technology Lanna (RMUTL), Chiangmai, Thailand. To illustrate, the paper refers to two typologies of feeder models, which are the convention and the school in factory (SiF) models. The new SiF model is developed through a collaborative educational process between the sectors of industry, government and academia, using work-integrated learning. The research methodology were use to compared features of the the SiF model with conventional models in terms of learning outcome, funding budget for the study, the advantages and disadvantages from the point of view of students, professors, the university, government and industrial partners. The results of this research indicate that the developed SiF feeder model is the most pertinent ones as it meet the requirements of the university, the government and the industry. The SiF feeder model showed the ability to yield positive learning outcomes with low expenditures per student for both the family and the university. In parallel, the sharing of knowledge between university and industry became increasingly important in the process, which resulted in the improvement of industrial skills for professors and an increase in industrial based research for the university. The SiF feeder model meets its demand of public policy in supporting a skilled workforce for the industry, which could be an effective tool for the triple helix educational model of Thailand.

  18. EV Charging Facilities and Their Application in LV Feeders with Photovoltaics

    DEFF Research Database (Denmark)

    Marra, Francesco; Yang, Guangya; Træholt, Chresten

    2013-01-01

    Low-voltage (LV) grid feeders with high penetration of photovoltaics (PVs) are often affected by voltage magnitude problems. To solve such issues, previous research has shown that reactive power methods, active power curtailment and grid reinforcement can be used for voltage support, yet showing...... several limits. We introduce the use of electric vehicle (EV) public charging stations with energy storage system (ESS) as a solution for voltage regulation in LV feeders with PV. A novel method is proposed to determine the ESS charging load required for voltage regulation and compare the results...... for the different locations in the feeder. With time-series simulations, we quantify the energy size required for a station ESS. A Belgian LV residential grid, modeled using real PV generation and load profiles, is used as case study. The method and simulation results show the effectiveness of using public EV...

  19. Convex relaxation of Optimal Power Flow in Distribution Feeders with embedded solar power

    DEFF Research Database (Denmark)

    Hermann, Alexander Niels August; Wu, Qiuwei; Huang, Shaojun

    2016-01-01

    There is an increasing interest in using Distributed Energy Resources (DER) directly coupled to end user distribution feeders. This poses an array of challenges because most of today’s distribution feeders are designed for unidirectional power flow. Therefore when installing DERs such as solar...... panels with uncontrolled inverters, the upper limit of installable capacity is quickly reached in many of today’s distribution feeders. This problem can often be mitigated by optimally controlling the voltage angles of inverters. However, the optimal power flow problem in its standard form is a large...... scale non-convex optimization problem, and thus can’t be solved precisely and also is computationally heavy and intractable for large systems. This paper examines the use of a convex relaxation using Semi-definite programming to optimally control solar power inverters in a distribution grid in order...

  20. A probabilistic degradation model for the estimation of the remaining life distribution of feeders

    International Nuclear Information System (INIS)

    Yuan, X.-X.; Pandey, M.D.; Bickel, G.A.

    2006-01-01

    Wall thinning due to flow accelerated corrosion (FAC) is a pervasive form of degradation in the outlet feeder pipes of the primary heat transport system of CANDU reactors. The prediction of the end-of-life of a feeder from wall thickness measurement data is confounded by the sampling and temporal uncertainties associated with the FAC degradation phenomenon. Traditional regression-based statistical methods deal with only the sampling uncertainties, leaving the temporal uncertainties unresolved. This paper presents an advanced probabilistic model, which is able to integrate the temporal uncertainties into the prediction of lifetime. In particular, a random gamma process model is proposed to model the FAC process and it is calibrated with a set of wall thickness measurements using the method of maximum likelihood. This information can be used to establish an optimum strategy for inspection and replacement of feeders. (author)

  1. Impact of Distribution Feeders that do not have Voltage Regulators on the number of Charged Electric Vehicles using IEEE 34 Bus Test Feeder

    Energy Technology Data Exchange (ETDEWEB)

    Allehyani, Ahmed [University of Southern California, Department of Electrical Engineering; Beshir, Mohammed [University of Southern California, Department of Electrical Engineering

    2015-02-01

    Voltage regulators help maintain an acceptable voltage profile for the system. This paper discusses the effect of installing voltage regulators to the system to fix the voltage drop resulting from the electrical vehicles loading increase when they are being charged. The effect will be studied in the afternoon, when the peak load occurs, using the IEEE 34 bus test feeder. First, only one spot node is used to charge the electric vehicles while a voltage regulator is present. Second, five spot nodes are loaded at the same time to charge the electric vehicles while voltage regulators are installed at each node. After that, the impact of electric vehicles on distribution feeders that do not have voltage regulators will appear.

  2. Computed tomography evaluation of human mandibles with regard to layer thickness and bone density of the cortical bone

    International Nuclear Information System (INIS)

    Markwardt, Jutta; Meissner, H.; Weber, A.; Reitemeier, B.; Laniado, M.

    2013-01-01

    Application of function-restoring individual implants for the bridging of defects in mandibles with continuity separation requires a stable fixation with special use of the cortical bone stumps. Five section planes each of 100 computed tomographies of poly-traumatized patients' jaws were used for measuring the thickness of the cortical layer and the bone density of the mandible. The CT scans of 28 female and 72 male candidates aged between 12 and 86 years with different dentition of the mandible were available. The computed tomographic evaluations of human mandibles regarding the layer thickness of the cortical bone showed that the edge of the mandible in the area of the horizontal branch possesses the biggest layer thickness of the whole of the lower jaws. The highest medians of the cortical bone layer thickness were found in the area of the molars and premolars at the lower edge of the lower jaws in 6-o'clock position, in the area of the molars in the vestibular cranial 10-o'clock position and in the chin region lingual-caudal in the 4-o'clock position. The measurement of the bone density showed the highest values in the 8-o'clock position (vestibular-caudal) in the molar region in both males and females. The average values available of the bone density and the layer thickness of the cortical bone in the various regions of the lower jaw, taking into consideration age, gender and dentition, are an important aid in practice for determining a safe fixation point for implants in the area of the surface layer of the mandible by means of screws or similar fixation elements. (orig.)

  3. Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de La Muerte, Costa Rica

    Directory of Open Access Journals (Sweden)

    Gerardo Avalos

    2012-03-01

    Full Text Available Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis, dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads, and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon. Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of

  4. Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de la Muerte, Costa Rica.

    Science.gov (United States)

    Avalos, Gerardo; Soto, Alejandra; Alfaro, Willy

    2012-03-01

    Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant) and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis), dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads), and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon). Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of captured

  5. A feeder protection method against the phase-phase fault using symmetrical components

    DEFF Research Database (Denmark)

    Ciontea, Catalin-Iosif; Bak, Claus Leth; Blaabjerg, Frede

    2017-01-01

    generation and relatively reduced short-circuit currents, thus resembling the electric network on a ship. The simulation results demonstrate that the proposed method of protection provides an improved performance compared to the conventional OverCurrent relays in a radial feeder with variable short......The method of symmetrical components simplifies analysis of an electric circuit during the fault and represents an important tool for the protection engineers. In this paper, the symmetrical components of the fault current are used in a new feeder protection method for the maritime applications...

  6. Multilayered Films Produced by Layer-by-Layer Assembly of Chitosan and Alginate as a Potential Platform for the Formation of Human Adipose-Derived Stem Cell aggregates

    Directory of Open Access Journals (Sweden)

    Javad Hatami

    2017-09-01

    Full Text Available The construction of multilayered films with tunable properties could offer new routes to produce biomaterials as a platform for 3D cell cultivation. In this study, multilayered films produced with five bilayers of chitosan and alginate (CHT/ALG were built using water-soluble modified mesyl and tosyl–CHT via layer-by-layer (LbL self-assembly. NMR results demonstrated the presences of mesyl (2.83 ppm and tosyl groups (2.39, 7.37 and 7.70 ppm in the chemical structure of modified chitosans. The buildup of multilayered films was monitored by quartz-crystal-microbalance (QCM-D and film thickness was estimated using the Voigt-based viscoelastic model. QCM-D results demonstrated that CHT/ALG films constructed using mesyl or tosyl modifications (mCHT/ALG were significantly thinner in comparison to the CHT/ALG films constructed with unmodified chitosan (p < 0.05. Adhesion analysis demonstrated that human adipose stem cells (hASCs did not adhere to the mCHT/ALG multilayered films and formed aggregates with sizes between ca. 100–200 µm. In vitro studies on cell metabolic activity and live/dead staining suggested that mCHT/ALG multilayered films are nontoxic toward hACSs. Multilayered films produced via LbL assembly of ALG and off-the-shelf, water-soluble modified chitosans could be used as a scaffold for the 3D aggregates formation of hASCs in vitro.

  7. Analyte-Size-Dependent Ionization and Quantification of Monosaccharides in Human Plasma Using Cation-Exchanged Smectite Layers.

    Science.gov (United States)

    Ding, Yuqi; Kawakita, Kento; Xu, Jiawei; Akiyama, Kazuhiko; Fujino, Tatsuya

    2015-08-04

    Smectite, a synthetic inorganic polymer with a saponite structure, was subjected to matrix-assisted laser desorption/ionization mass spectrometry (MALDI MS). Typical organic matrix molecules 2,4,6-trihydroxyacetophenone (THAP) and 2,5-dihydroxybenzoic acid (DHBA) were intercalated into the layer spacing of cation-exchanged smectite, and the complex was used as a new matrix for laser desorption/ionization mass spectrometry. Because of layer spacing limitations, only a small analyte that could enter the layer and bind to THAP or DHBA could be ionized. This was confirmed by examining different analyte/matrix preparation methods and by measuring saccharides with different molecular sizes. Because of the homogeneous distribution of THAP molecules in the smectite layer spacing, high reproducibility of the analyte peak intensity was achieved. By using isotope-labeled (13)C6-d-glucose as the internal standard, quantitative analysis of monosaccharides in pretreated human plasma sample was performed, and the value of 8.6 ± 0.3 μg/mg was estimated.

  8. Quantitative analysis of basal dendritic tree of layer III pyramidal neurons in different areas of adult human frontal cortex.

    Science.gov (United States)

    Zeba, Martina; Jovanov-Milosević, Natasa; Petanjek, Zdravko

    2008-01-01

    Large long projecting (cortico-cortical) layer IIIc pyramidal neurons were recently disclosed to be in the basis of cognitive processing in primates. Therefore, we quantitatively examined the basal dendritic morphology of these neurons by using rapid Golgi and Golgi Cox impregnation methods among three distinct Brodmann areas (BA) of an adult human frontal cortex: the primary motor BA4 and the associative magnopyramidal BA9 from left hemisphere and the Broca's speech BA45 from both hemispheres. There was no statistically significant difference in basal dendritic length or complexity, as dendritic spine number or their density between analyzed BA's. In addition, we analyzed each of these BA's immunocytochemically for distribution of SMI-32, a marker of largest long distance projecting neurons. Within layer IIIc, the highest density of SMI-32 immunopositive pyramidal neurons was observed in associative BA9, while in primary BA4 they were sparse. Taken together, these data suggest that an increase in the complexity of cortico-cortical network within human frontal areas of different functional order may be principally based on the increase in density of large, SMI-32 immunopositive layer IIIc neurons, rather than by further increase in complexity of their dendritic tree and synaptic network.

  9. Split bundle detection in polarimetric images of the human retinal nerve fiber layer

    NARCIS (Netherlands)

    Vermeer, K. A.; Reus, N. J.; Vos, F. M.; Lemij, H. G.; Vossepoel, A. M.

    2007-01-01

    One method for assessing pathological retinal nerve fiber layer (NFL) appearance is by comparing the NFL to normative values, derived from healthy subjects. These normative values will be more specific when normal physiological differences are taken into account. One common variation is a split

  10. Does proximity to urban centres affect the dietary regime of marine benthic filter feeders?

    Science.gov (United States)

    Puccinelli, Eleonora; Noyon, Margaux; McQuaid, Christopher D.

    2016-02-01

    Threats to marine ecosystems include habitat destruction and degradation of water quality, resulting from land- and ocean-based human activities. Anthropogenic input causing modification of water quality, can affect primary productivity and thus food availability and quality for higher trophic levels. This is especially important for sedentary benthic intertidal communities, which rely on local food availability. We investigated the effect of urbanization on the dietary regime of four species of intertidal filter feeders (three barnacles and one mussel) at sites close to high-density cities and at sites far from heavily urbanized areas using fatty acid and stable isotope techniques. δ15N was significantly higher at urbanized sites compared to their corresponding control sites for all species with few exceptions, while no effect on δ13C was recorded. Barnacle fatty acid profiles were not affected by cities, while mussels from sites close to cities had fatty acid signatures with a higher proportion of polyunsaturated fatty acids (PUFA). We suggest that the enrichment in δ15N at urbanised sites reflects the influence of anthropogenically derived nitrogen directly linked to wastewater input from domestic and industrial sewage. Linked to this, the high proportion of PUFA in mussels at urbanized sites may reflect the influence of increased nitrogen concentrations on primary production and enhanced growth of large phytoplankton cells. The results indicate that anthropogenic effects can strongly influence the diets of benthic organisms, but these effects differ among taxa. Changes in the diet of such habitat forming species can affect their fitness and survival with potential effects on the populations associated with them.

  11. The impact of small benthic passive suspension feeders in shallow marine ecosystems: the hydroids as an example

    NARCIS (Netherlands)

    Gili, J.-M.; Alvà, V.; Coma, R.; Orejas, C.; Pagès, F.; Ribes, M.; Zabala, M.; Arntz, W.; Bouillon, J.; Boero, F.; Hughes, R.G.

    1998-01-01

    Benthic suspension feeders are abundant in littoral and shallow sub-littoral ecosystems, where they feed on the plankton and on organic matter suspended in the water column. Recent studies indicate that active suspension feeders with powerful water filtration mechanisms (e.g., bivalve molluscs) may

  12. Histological features of layers and sublayers in cortical visual areas V1 and V2 of chimpanzees, macaque monkeys, and humans

    Directory of Open Access Journals (Sweden)

    Balaram P

    2014-09-01

    Full Text Available Pooja Balaram, Nicole A Young, Jon H Kaas Department of Psychology, Vanderbilt University, Nashville, TN, USA Abstract: The layers and sublayers of primary visual cortex, or V1, in primates are easily distinguishable compared to those in other cortical areas, and are especially distinct in anthropoid primates – monkeys, apes, and humans – where they also vary in histological appearance. This variation in primate-specific specialization has led to a longstanding confusion over the identity of layer 4 and its proposed sublayers in V1. As the application of different histological markers relate to the issue of defining and identifying layers and sublayers, we applied four traditional and four more recent histological markers to brain sections of V1 and adjoining secondary visual cortex (V2 in macaque monkeys, chimpanzees, and humans in order to compare identifiable layers and sublayers in both cortical areas across these species. The use of Nissl, neuronal nuclear antigen (NeuN, Gallyas myelin, cytochrome oxidase (CO, acetylcholinesterase (AChE, nonphosphorylated neurofilament H (SMI-32, parvalbumin (PV, and vesicular glutamate transporter 2 (VGLUT2 preparations support the conclusion that the most popular scheme of V1 lamination, that of Brodmann, misidentifies sublayers of layer 3 (3Bβ and 3C as sublayers of layer 4 (4A and 4B, and that the specialized sublayer of layer 3 in monkeys, 3Bβ, is not present in humans. These differences in interpretation are important as they relate to the proposed functions of layer 4 in primate species, where layer 4 of V1 is a layer that receives and processes information from the visual thalamus, and layer 3 is a layer that transforms and distributes information to other cortical areas. Keywords: area 17, area 18, cortical layers, histology, immunohistochemistry

  13. A simple and efficient feeder-free culture system to up-scale iPSCs on polymeric material surface for use in 3D bioprinting.

    Science.gov (United States)

    Wong, Chui-Wei; Chen, You-Tzung; Chien, Chung-Liang; Yu, Tien-Yu; Rwei, Syang-Peng; Hsu, Shan-Hui

    2018-01-01

    The 3D bioprinting and cell/tissue printing techniques open new possibilities for future applications. To facilitate the 3D bioprinting process, a large amount of living cells are required. Induced pluripotent stem cells (iPSCs) represent a promising cell source for bioprinting. However, the maintenance and expansion of undifferentiated iPSCs are expensive and time consuming. Therefore, in this study a culture method to obtain a sufficient amount of healthy and undifferentiated iPSCs in a short-term period was established. The iPSCs could be passaged for twice on tissue culture polystyrene (TCPS) dish with the conditional medium and could adapt to the feeder-free environment. Feeder-free dishes were further prepared from chitosan, chitosan-hyaluronan, silk fibroin, and polyurethane (PU1 and PU2) two-dimensional substrates. The iPSCs cultured on the chitosan substrates showed a higher proliferation rate without losing the stemness feature. Among the different materials, PU2 could be prepared as a thermoresponsive hydrogel, which was a potential ink for 3D bioprinting. The iPSCs cultured on PU2 substrates well survived when further embedded in PU2 hydrogel. Moreover, PU2 hydrogel printed with iPSCs remained structural integrity. The use of PU2 hydrogel to embed iPSCs reduced the injury to iPSCs by shear stress. These results indicate that iPSCs could be expanded on chitosan or PU2 membranes without the feeder layer and then printed in PU2 hydrogel. The combination of these steps could offer a new possibility for future applications of iPSC-based 3D bioprinting in tissue engineering. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. A laser syringe aimed at delivering drug into the outer layer of human skin

    Science.gov (United States)

    Yoh, Jack J.; Jang, Hun-jae; Park, Mi-ae; Han, Tae-hee; Hah, Jung-moo

    2012-07-01

    A desire to eliminate hypodermic needle in transdermal drug delivery may now be realized. Imaging of the skin after injection of fluorescent probe and biotin via the bio-ballistic technique revealed the epidermal and dermal layers which were stained well below 60 μm underneath the abdominal skin of the guinea-pig. An extensive network of cells are shown in the deeper layer of the stained dermis as the distributed fluorescein isothiocyanate (FITC) dose is administered by repeated injection via the laser-based microjet. Here, we show our method of laser-based microjet drug delivery is capable of breaching guinea-pig's skin tissue and then delivering controlled dose of drug to the targeted region between 10 to 400 μm underneath the outermost layer of the skin. While minimizing pain and tissue damage by reducing the injection volume to ˜100 nl per pulse and the microjet diameter of half the conventional syringe needle in 100 μm, the optimally controlled delivery of liquid drug by the irradiated laser pulse is shown possible.

  15. Optimalisatie performance van vleeskuikens bij mobiel voer- en drinksysteem (scanFeeder) op praktijkbedrijf

    NARCIS (Netherlands)

    Harn, van J.; Veldkamp, T.

    2007-01-01

    Het gebruik van de Ridder ScanFeeder, een mobiel voer- en drinksysteem met strooiselbeluchting voor vleeskuikens, geeft een betere strooiselkwaliteit (ruller en droger strooisel) en minder voetzoolaandoeningen. De technische resultaten bij dit systeem blijven echter achter bij die van een

  16. Hybrid RSOA and fibre raman amplified long reach feeder link for WiMAX-on-fibre

    DEFF Research Database (Denmark)

    Amaya Fernández, Ferney Orlando; Martinez, Javier; Yu, Xianbin

    2009-01-01

    A distributed fibre Raman amplified long reach optical access feeder link using a reflective semiconductor optical amplifier in the remote base station is experimentally demonstrated for supporting WiMAXover- fibre transmission. The measured values for the error vector magnitude for quadrature...

  17. Tits recognize the potential dangers of predators and harmless birds in feeder experiments

    Czech Academy of Sciences Publication Activity Database

    Tvardíková, Kateřina; Fuchs, R.

    2012-01-01

    Roč. 30, č. 1 (2012), s. 157-165 ISSN 0289-0771 Grant - others:AV ČR(CZ) IAA601410803 Institutional research plan: CEZ:AV0Z50070508 Keywords : feeders * predator recognition * risk Subject RIV: EH - Ecology, Behaviour Impact factor: 1.000, year: 2012 http://www.springerlink.com/content/2338033t30261604/fulltext.pdf

  18. Evolution of generic supporting conditions for feeders of 500 M We PHWR

    International Nuclear Information System (INIS)

    Prasad, K.H.; Gupta, K.N.; Bapat, C.N.; Sharma, V.K.; Mishra, R.; Soni, R.S.; Kushwaha, H.S.; Mahajan, S.C.; Kakodkar, A.

    1995-01-01

    Feeder piping consists of 784 number of closely spaced, inter-connected flexible pipes catering for large thermal and creep movements besides seismic and other loadings. The analytical strategy for evolving generic supporting conditions is outlined in this paper. (author). 4 refs., 7 figs

  19. Effects of an increasing filter feeder stock on larval abundance in the Oosterschelde estuary (SW Netherlands)

    NARCIS (Netherlands)

    Troost, Karin; Gelderman, Edzard; Kamermans, Pauline; Smaal, Aad C.; Wolff, Wim J.

    Predation by adult bivalves oil bivalve larvae has been suggested to reduce larval abundance in areas with high bivalve filter-feeder biomass. Although the occurrence of larviphagy is well-studied in the laboratory, its effects in the field have scarcely been studied. We studied larviphagy at

  20. Effects of an increasing filter feeder stock on larval abundance in the Oosterschelde estuary (SW Netherlands)

    NARCIS (Netherlands)

    Troost, K.; Gelderman, E.A.C.; Kamermans, P.; Smaal, A.C.; Wolff, W.

    2009-01-01

    Predation by adult bivalves on bivalve larvae has been suggested to reduce larval abundance in areas with high bivalve filter-feeder biomass. Although the occurrence of larviphagy is well-studied in the laboratory, its effects in the field have scarcely been studied. We studied larviphagy at

  1. Interactions among contaminant exposure route, kinetics and toxicity in marine deposit-feeders

    DEFF Research Database (Denmark)

    Selck, Henriette

    Many of the chemicals having the greatest likelihood of causing damage in ecological systems, such as polycyclic aromatic hydrocarbons (PAHs) and metals are of persistent and/or hydrophobic character. Deposit-feeders may be important in facilitating the removal of organic contaminants from bulk...

  2. Feeder Cell Type Affects the Growth of In Vitro Cultured Bovine Trophoblast Cells

    Directory of Open Access Journals (Sweden)

    Islam M. Saadeldin

    2017-01-01

    Full Text Available Trophectoderm cells are the foremost embryonic cells to differentiate with prospective stem-cell properties. In the current study, we aimed at improving the current approach for trophoblast culture by using granulosa cells as feeders. Porcine granulosa cells (PGCs compared to the conventional mouse embryonic fibroblasts (MEFs were used to grow trophectoderm cells from hatched bovine blastocysts. Isolated trophectoderm cells were monitored and displayed characteristic epithelial/cuboidal morphology. The isolated trophectoderm cells expressed mRNA of homeobox protein (CDX2, cytokeratin-8 (KRT8, and interferon tau (IFNT. The expression level was higher on PGCs compared to MEFs throughout the study. In addition, primary trophectoderm cell colonies grew faster on PGCs, with a doubling time of approximately 48 hrs, compared to MEFs. PGCs feeders produced a fair amount of 17β-estradiol and progesterone. We speculated that the supplementation of sex steroids and still-unknown factors during the trophoblasts coculture on PGCs have helped to have better trophectoderm cell’s growth than on MEFs. This is the first time to use PGCs as feeders to culture trophectoderm cells and it proved superior to MEFs. We propose PGCs as alternative feeders for long-term culture of bovine trophectoderm cells. This model will potentially benefit studies on the early trophoblast and embryonic development in bovines.

  3. The effect of stocking density and bin feeder space on performance ...

    African Journals Online (AJOL)

    Unknown

    The effect of stocking density and bin feeder space on performance in pigs. G.A. Lavers# and N.S. Ferguson. School of Agricultural Sciences & Agribusiness, University of Natal, P Bag X01, Scottsville 3209. #Email: lavers@agric.unp.ac.za. Introduction. Pigs housed individually have been shown to have higher feed intakes ...

  4. The effect of stocking density and bin feeder space on performance ...

    African Journals Online (AJOL)

    The effect of stocking density and bin feeder space on performance in pigs. G.A. Lavers, N.S. Ferguson. Abstract. (South African J of Animal Science, 2000, 30, Supplement 1: 70-71). Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

  5. Tumor Volume Decrease via Feeder Occlusion for Treating a Large, Firm Trigone Meningioma.

    Science.gov (United States)

    Nakashima, Takuma; Hatano, Norikazu; Kanamori, Fumiaki; Muraoka, Shinsuke; Kawabata, Teppei; Takasu, Syuntaro; Watanabe, Tadashi; Kojima, Takao; Nagatani, Tetsuya; Seki, Yukio

    2018-01-01

    Trigone meningiomas are considered a surgical challenge, as they tend to be considerably large and hypervascularized at the time of presentation. We experienced a case of a large and very hard trigone meningioma that was effectively treated using initial microsurgical feeder occlusion followed by surgery in stages. A 19-year-old woman who presented with loss of consciousness was referred to our hospital for surgical treatment of a brain tumor. Radiological findings were compatible with a left ventricular trigone meningioma extending laterally in proximity to the Sylvian fissure. At initial surgery using the transsylvian approach, main feeders originating from the anterior and lateral posterior choroidal arteries were occluded at the inferior horn; however, only a small section of the tumor could initially be removed because of its firmness. Over time, feeder occlusion resulted in tumor necrosis and a 20% decrease in its diameter; the mass effect was alleviated within 1 year. The residual meningioma was then totally excised in staged surgical procedures after resection became more feasible owing to ischemia-induced partial softening of the tumor. When a trigone meningioma is large and very hard, initial microsurgical feeder occlusion in the inferior horn can be a safe and effective option, and can lead to necrosis, volume decrease, and partial softening of the residual tumor to allow for its staged surgical excision.

  6. Operation of a cell feeder for coal controlled by a frequency converter. [Czechoslovakia

    Energy Technology Data Exchange (ETDEWEB)

    Stonawski, J; Sikora, G

    1984-02-01

    Steam boiler of the Trinec coal-fired power plant with a capacity of 125 t/h, 545 C, 9.5 MPa was equipped with a screw coal feeder with the KT26A-6 Winter-Eichberg motor with a transformer. The screw fee

  7. Co-ordination of directional overcurrent protection with load current for parallel feeders

    Energy Technology Data Exchange (ETDEWEB)

    Wright, J.W.; Lloyd, G.; Hindle, P.J. [Alstom, Inc., Stafford (United Kingdom). T and D Protection and Control

    1999-11-01

    Directional phase overcurrent relays are commonly applied at the receiving ends of parallel feeders or transformer feeders. Their purpose is to ensure full discrimination of main or back-up power system overcurrent protection for a fault near the receiving end of one feeder. This paper reviews this type of relay application and highlights load current setting constraints for directional protection. Such constraints have not previously been publicized in well-known text books. A directional relay current setting constraint that is suggested in some text books is based purely on thermal rating considerations for older technology relays. This constraint may not exist with modern numerical relays. In the absence of any apparent constraint, there is a temptation to adopt lower current settings with modern directional relays in relation to reverse load current at the receiving ends of parallel feeders. This paper identifies the danger of adopting very low current settings without any special relay feature to ensure protection security with load current during power system faults. A system incident recorded by numerical relays is also offered to highlight this danger. In cases where there is a need to infringe the identified constraints an implemented and testing relaying technique is proposed.

  8. A Branch-and-Price Approach to the Feeder Network Design Problem

    DEFF Research Database (Denmark)

    Santini, Alberto; Plum, Christian Edinger Munk; Røpke, Stefan

    2017-01-01

    In this paper we consider the problem of designing a container liner shipping feeder network. The designer has to choose which port to serve during many rotations that start and end at a central hub. Many operational characteristics are considered, such as variable leg-by-leg speeds and cargo...

  9. harmonic load modeling: a case study of 33 kv abuja steel mill feeder

    African Journals Online (AJOL)

    HOD

    An in-depth study of the harmonic orders inherent in a power system network is required ... This paper studied the harmonic orders of the 33 kV Abuja Steel Feeder .... models for various industrial and household electrical ..... Malaysia, 2013.

  10. Optimal Design of the Feeder-Bus Network Based on the Transfer System

    Directory of Open Access Journals (Sweden)

    Lianbo Deng

    2013-01-01

    Full Text Available This paper studied the classic feeder-bus network design problem (FBNDP, which can be described as follows: for the passenger travel demand between rail stations and bus stops on a given urban transit network, it designs the optimal feeder bus routes and frequencies so as to minimize the passengers’ travel expense and the operator’s cost. We extended the demand pattern of M-to-1 in most existing researches to M-to-M. We comprehensively considered the passenger travel cost, which includes the waiting and riding cost on the bus, riding cost on rail, and transfer cost between these two transportation modes, and presented a new genetic algorithm that determines the optimal feeder-bus operating frequencies under strict constraint conditions. The numerical examples under different demand patterns have been experienced and analysed, which showed the robustness and efficiency of the presented algorithm. We also found that the distribution pattern of the travel demand has a significant influence on the feeder-bus network construction.

  11. BC Hydro's integrated approach on replacing underground feeder cables

    Energy Technology Data Exchange (ETDEWEB)

    Tarampi, D. [BC Hydro, Burnaby, BC (Canada)

    2008-07-01

    BC Hydro's integrated approach on replacing underground feeder cables was discussed. The feeder cables were all in ducts encased in concrete and splices were identified in concrete manholes. The feeder cables averaged 35 to 40 failures per year, with a large majority of failures occurring in manholes or near terminations. The age of the cables was not known. A graphical representation of a condition assessment was presented with reference to an electrical test, metallurgical test, hardness test, and dye penetrating test. Prioritization steps were also listed, including a condition index and replacement threshold. Steps in prioritizing the condition index included determining the insulation index based on electrical test results; determining the manhole condition based on metallurgical test results; determining the customer importance factor and feeder load factor; and calculating the overall condition index based on the indices. A process flowchart was also illustrated. A replacement strategy was then discussed and a cost comparison of two options was described. Option 1 was to replace only the unjacketed cables while option two involved selective replacement. tabs., figs.

  12. Impact of feeder space on laying hen feeding behavior and production performance in enriched colony housing.

    Science.gov (United States)

    Oliveira, J L; Xin, H; Wu, H

    2018-05-30

    Current feeder space recommendations in laying hen welfare guidelines are inconsistent among and within countries. One determining criterion forming the recommendations (e.g. 12.0 cm/hen for the EU guideline) is that all birds can feed simultaneously. However, if there are other resources in the environment, as in enriched colony housing (ECH), it is unknown whether group-housed hens will choose to feed simultaneously. This study assesses the impact of feeder space on feeding behavior of 60 laying hens (W-36) in ECH using a ultra-high frequency radio-frequency identification-based tracking system. The feeder spaces investigated were 12.0, 9.5, 8.5 and 6.5 cm/hen, achieved by blocking portions of the overall feeder access to keep hens at the same stocking density. Each feeder space treatment, randomly assigned over the course of the experiment, lasted for 7 consecutive days. Feeding behaviors were characterized as daily time spent at the feeder (TS, min/hen-day), daily frequency of visits to the feeder (FV, #/hen-day), and maximum or average percentage of hens feeding simultaneously (MPB, APB, %). Group-average daily feed intake (FI, g/hen-day), water use (WU, g/hen-day), and hen-day egg production (HDEP, %) were also measured. The results revealed that at 12.0 cm/hen, where unoccupied feeder space was present, a maximum of 59.0±1.4% (average of 31.7±0.3%) hens fed simultaneously. No significant differences were detected among 12.0, 9.5 and 8.5 cm/hen in TS (293±10, 286±10 and 281±10 min/hen-day) and MPB (59.0±1.4, 57.3±1.4 and 53.3±1.4%) (P>0.05). The outcome of no significant differences also held true between 12.0 and 9.5 cm/hen in APB (31.7±0.3 v. 30.8±0.3%) and between 9.5 and 8.5 cm/hen in all response variables measured (P>0.05). However, there were significant differences in APB between 6.5 cm/hen and all other treatments; in TS and FV between 6.5 and 9.5 cm/hen; and in MPB between 6.5 and 12 cm/hen (P0.05). The results revealed that synchronous

  13. Mass transfer effects in feeder flow-accelerated corrosion wall thinning

    International Nuclear Information System (INIS)

    Pietralik, J.

    2008-01-01

    Flow conditions play a dominant role in Flow-Accelerated Corrosion (FAC) under certain conditions, e.g., in CANDU feeders. While chemistry and materials set the overall potential for FAC, flow conditions determine the local distribution of wall thinning. Recent plant data of feeders and laboratory tests confirms that there is a close relationship between local flow conditions, expressed by mass transfer coefficient, and FAC rate in CANDU feeder bends. The knowledge of local effects can be useful for minimizing the number of inspected components, predicting the location of the highest FAC rate for a given piping component, and determining what components or feeders should be replaced. A similar evaluation applies also to FAC in heat transfer equipment such as heat exchangers and steam generators. The objective of this paper is to examine the relationship between FAC rate and local mass transfer parameters. For FAC where the flow is dominant, the FAC rate is proportional to mass flux of ferrous ions. The mass flux is the product of the mass transfer coefficient and the concentration difference, or degree of saturation. The mass transfer coefficient describes the intensity of the transport of corrosion products (ferrous ions) from the oxide-water interface into the bulk water. Therefore, this parameter can be used for predicting the local distribution of FAC rate in the mass-transfer controlled FAC. The degree of saturation reduces the mass flux, thus reducing the FAC rate. This effect can be significant in long piping, e.g., in outlet feeders. The paper presents plant and laboratory evidence for the relationship between local mass transfer conditions and the FAC rate. It shows correlations for mass transfer coefficient in components that are highly susceptible to FAC and most important flow parameters that affect mass transfer coefficient. The role of surface roughness, wall shear stress, and local turbulence is also discussed. (author)

  14. Histological features of layers and sublayers in cortical visual areas V1 and V2 of chimpanzees, macaque monkeys, and humans.

    Science.gov (United States)

    Balaram, Pooja; Young, Nicole A; Kaas, Jon H

    2014-09-01

    The layers and sublayers of primary visual cortex, or V1, in primates are easily distinguishable compared to those in other cortical areas, and are especially distinct in anthropoid primates - monkeys, apes, and humans - where they also vary in histological appearance. This variation in primate-specific specialization has led to a longstanding confusion over the identity of layer 4 and its proposed sublayers in V1. As the application of different histological markers relate to the issue of defining and identifying layers and sublayers, we applied four traditional and four more recent histological markers to brain sections of V1 and adjoining secondary visual cortex (V2) in macaque monkeys, chimpanzees, and humans in order to compare identifiable layers and sublayers in both cortical areas across these species. The use of Nissl, neuronal nuclear antigen (NeuN), Gallyas myelin, cytochrome oxidase (CO), acetylcholinesterase (AChE), nonphosphorylated neurofilament H (SMI-32), parvalbumin (PV), and vesicular glutamate transporter 2 (VGLUT2) preparations support the conclusion that the most popular scheme of V1 lamination, that of Brodmann, misidentifies sublayers of layer 3 (3Bβ and 3C) as sublayers of layer 4 (4A and 4B), and that the specialized sublayer of layer 3 in monkeys, 3Bβ, is not present in humans. These differences in interpretation are important as they relate to the proposed functions of layer 4 in primate species, where layer 4 of V1 is a layer that receives and processes information from the visual thalamus, and layer 3 is a layer that transforms and distributes information to other cortical areas.

  15. Effect of aquatine endodontic cleanser on smear layer removal in the root canals of ex vivo human teeth

    Directory of Open Access Journals (Sweden)

    Faustino Garcia

    2010-08-01

    Full Text Available OBJECTIVES: The purpose of this study was to measure and compare the root canal cleanliness and smear layer removal effectiveness of Aquatine Endodontic Cleanser (Aquatine EC when used as an endodontic irrigating solution in comparison with 6% sodium hypochlorite (NaOCl. MATERIAL AND METHODS: Forty-five human teeth were randomly allocated to five treatment groups; the pulp chamber was accessed, cleaned, and shaped by using ProTaper and ProFile rotary instrumentation to an ISO size #40. The teeth were then processed for scanning electron microscopy, and the root canal cleanliness and removal of smear layer were examined. RESULTS: The most effective removal of smear layer occurred with Aquatine EC and NaOCl, both with a rinse of EDTA. CONCLUSIONS: Aquatine EC appears to be the first hypochlorous acid approved by the FDA to be a possible alternative to the use of NaOCl as an intracanal irrigant. Further research is needed to identify safer and more effective alternatives to the use of NaOCl irrigation in endodontics.

  16. Resilient protein co-expression network in male orbitofrontal cortex layer 2/3 during human aging.

    Science.gov (United States)

    Pabba, Mohan; Scifo, Enzo; Kapadia, Fenika; Nikolova, Yuliya S; Ma, Tianzhou; Mechawar, Naguib; Tseng, George C; Sibille, Etienne

    2017-10-01

    The orbitofrontal cortex (OFC) is vulnerable to normal and pathologic aging. Currently, layer resolution large-scale proteomic studies describing "normal" age-related alterations at OFC are not available. Here, we performed a large-scale exploratory high-throughput mass spectrometry-based protein analysis on OFC layer 2/3 from 15 "young" (15-43 years) and 18 "old" (62-88 years) human male subjects. We detected 4193 proteins and identified 127 differentially expressed (DE) proteins (p-value ≤0.05; effect size >20%), including 65 up- and 62 downregulated proteins (e.g., GFAP, CALB1). Using a previously described categorization of biological aging based on somatic tissues, that is, peripheral "hallmarks of aging," and considering overlap in protein function, we show the highest representation of altered cell-cell communication (54%), deregulated nutrient sensing (39%), and loss of proteostasis (35%) in the set of OFC layer 2/3 DE proteins. DE proteins also showed a significant association with several neurologic disorders; for example, Alzheimer's disease and schizophrenia. Notably, despite age-related changes in individual protein levels, protein co-expression modules were remarkably conserved across age groups, suggesting robust functional homeostasis. Collectively, these results provide biological insight into aging and associated homeostatic mechanisms that maintain normal brain function with advancing age. Copyright © 2017 Elsevier Inc. All rights reserved.

  17. Observation of the hypodermic fatty layer of the human torso by computed tomography method

    International Nuclear Information System (INIS)

    Matsuyama, Yoko; Inokuchi, Seiichiro; Suzuki, Masataka

    1984-01-01

    CT images were taken at 7 different longitudinal levels of the torso, and three different body types, which were defined by the Rohrer Index, were discussed. Differences between the sexes were also discussed. 1) Total cross-sectional area: In males, values showed maximum at 2 levels (mid-point of sternum, xiphoid) among 7 levels; and, for females, 2 maximal values appeared at the mid-point of the sternum level and the level of the pubic symphysis. Values at the umbilicus level were smallest in both sexes. 2) Areas of hypodermic fatty layer: Here, the values for males were maximal at the umbilicus level, next largest were found at the lower abdominal level. For females, however, the maximal values appeared at the pubic symphysis and lower abdominal levels and values for the umbilicus level followed in magnitude. 3) Hypodermic fatty layer area ratios to those of the total cross-sectional area: Values here were largest at the umbilicus level in both sexes. For males, the ratio at the lower abdominal level and at the pubic symphysis level followed in this order: For females, the order of magnitude of values was reversed between those two ratios. The most minimal ratio appeared at the level of the xiphoid in both sexes. A tendency towards higher ratios in females than in males was seen at all 7 levels for bodies of the A-type. This was seen, however, only at levels below the upper abdomen for bodies of the C-type, and at all levels, except the umbilicus and lower abdomen, for bodies of the D-type. 4) Thickness of the hypodermic fatty layer: The maximal values in this layer appeared at point F for the superior border, mid-point and xiphoid of sternum levels. For the upper abdominal level, maximal values appeared at point A, and for the umbilicus level, at point D. They were all found at point C for the lower abdominal level and at point A for the pubic symphysis level. (J.P.N.)

  18. The Adhesion of Lactobacillus salivarius REN to a Human Intestinal Epithelial Cell Line Requires S-layer Proteins.

    Science.gov (United States)

    Wang, Ran; Jiang, Lun; Zhang, Ming; Zhao, Liang; Hao, Yanling; Guo, Huiyuan; Sang, Yue; Zhang, Hao; Ren, Fazheng

    2017-03-10

    Lactobacillus salivarius REN, a novel probiotic isolated from Chinese centenarians, can adhere to intestinal epithelial cells and subsequently colonize the host. We show here that the surface-layer protein choline-binding protein A (CbpA) of L. salivarius REN was involved in adherence to the human colorectal adenocarcinoma cell line HT-29. Adhesion of a cbpA deletion mutant was significantly reduced compared with that of wild-type, suggesting that CbpA acts as an adhesin that mediates the interaction between the bacterium and its host. To identify the molecular mechanism of adhesion, we determined the crystal structure of a truncated form of CbpA that is likely involved in binding to its cell-surface receptor. The crystal structure identified CbpA as a peptidase of the M23 family whose members harbor a zinc-dependent catalytic site. Therefore, we propose that CbpA acts as a multifunctional surface protein that cleaves the host extracellular matrix and participates in adherence. Moreover, we identified enolase as the CbpA receptor on the surface of HT-29 cells. The present study reveals a new class of surface-layer proteins as well as the molecular mechanism that may contribute to the ability of L. salivarius REN to colonize the human gut.

  19. Real-Time Distribution Feeder Performance Monitoring, Advisory Control, and Health Management System

    Energy Technology Data Exchange (ETDEWEB)

    Stoupis, James; Mousavi, Mirrasoul

    2014-09-30

    New data collection system equipment was installed in Xcel Energy substations and data was collected from 6 substations and 20 feeders. During Phase I, ABB collected and analyzed 793 real-time events to date from 6 Xcel Energy substations and continues today. The development and integration of several applications was completed during the course of this project, including a model-based faulted segment identification algorithm, with very positive results validated with field-gathered data discussed and included in this report. For mostly underground feeders, the success rate is 90% and the overreach rate is 90%. For mostly overhead feeders, the success rate is 74% and the overreach rate is 50%. The developed method is producing very accurate results for mostly underground feeders. For mostly overhead feeders, due to the bad OMS data quality and varying fault resistance when arcing, the developed method is producing good results but with much room for improvement. One area where the algorithm can be improved is the accuracy for sub-cycle fault events. In these cases, the accuracy of the conventional signal processing methods suffers due to most of these methods being based on a one-cycle processing window. By improving the signal processing accuracy, the accuracy of the faulted segment identification algorithm will also improve significantly. ABB intends to devote research in this area in the near future to help solve this problem. Other new applications developed during the course of the project include volt/VAR monitoring, unbalanced capacitor switching detection, unbalanced feeder loading detection, and feeder overloading detection. An important aspect of the demonstration phase of the project is to show the ability to provide adequate “heads-up” time ahead of customer calls or AMI reports so that the operators are provided with the much needed time to collect information needed to address an outage. The advance notification feature of the demonstration system

  20. Metaplasia of the parietal layer of Bowman's capsule. A histopathological survey of the human kidney

    OpenAIRE

    Haensly, William E.; Lee, J.C.

    1986-01-01

    Human kidney sections taken at autopsy were examined to determine the incidence of metaplasia of the Bowman's parietal epithelium. Autopsy records were consulted to determine if there was any correlation between clinical disease, histopathological changes in organ systems and metaplasia of Bowman's capsule. The sections represented both sexes in 9 age groups from 2 to 87 years. The sections were fixed in neutral formalin, embedded in paraffin, sectioned at 6 pm...

  1. Mathematical modeling of laser linear thermal effects on the anterior layer of the human eye

    Science.gov (United States)

    Rahbar, Sahar; Shokooh-Saremi, Mehrdad

    2018-02-01

    In this paper, mathematical analysis of thermal effects of excimer lasers on the anterior side of the human eye is presented, where linear effect of absorption by the human eye is considered. To this end, Argon Fluoride (ArF) and Holmium:Yttrium-Aluminum-Garent (Ho:YAG) lasers are utilized in this investigation. A three-dimensional model of the human eye with actual dimensions is employed and finite element method (FEM) is utilized to numerically solve the governing (Penne) heat transfer equation. The simulation results suggest the corneal temperature of 263 °C and 83.4 °C for ArF and Ho:YAG laser radiations, respectively, and show less heat penetration depth in comparison to the previous reports. Moreover, the heat transfer equation is solved semi-analytically in one-dimension. It is shown that the exploited simulation results are also consistent with those derived from the semi-analytical solution of the Penne heat transfer equation for both types of laser radiations.

  2. High-resolution imaging of the layers of the gastrointestinal wall of pig and human specimens using an endoluminal MR receiver coil. Correlation to histology

    International Nuclear Information System (INIS)

    Kramer, Sebastian; Palmowski, M.; Macher-Goeppinger, S.; Mueller, M.; Volke, F.; Duex, M.; Kauczor, H.U.; Grenacher, L.

    2009-01-01

    Purpose: High-resolution MR imaging of the layers of the gastrointestinal wall to provide a foundation for tumor staging based on morphological criteria. Materials and Methods: Over a period of 12 months, miscellaneous parts of the gastrointestinal tract of 15 human specimens and 30 porcine specimens were scanned using a 1.5 Tesla clinical MRI scanner combined with an endoluminal receiver coil. The sequences used were T1-weighted opposed-phase, T2-weighted turbo spin echo with fat saturation and fast T2-weighted inversion recovery. The number of differentiable layers, their width and the signal intensity were documented. Then, the results were compared with histological specimens in order to link the imaged wall layers to the anatomical layers. Spearman's Rank Correlation was used to determine the soundness of the link between the images and their related histology. Results: For both human and animal specimens, the MRI scanning produced 3 to 5, maximum 6 (pig), differentiable layers. The mucosa, submucosa and muscularis could be differentiated with a hyperintense, hypointense and intermediary signal, respectively. The subserosal layer displayed a hypointense signal. Conclusion: High-resolution MRI is able to produce differentiable images of the anatomical layers of the gastrointestinal wall in both humans and pigs. Accordingly, it is possible to use MR imaging to diagnose the extent of local tumor infiltration of the gastrointestinal wall. (orig.)

  3. Lake Bacterial Assemblage Composition Is Sensitive to Biological Disturbance Caused by an Invasive Filter Feeder.

    Science.gov (United States)

    Denef, Vincent J; Carrick, Hunter J; Cavaletto, Joann; Chiang, Edna; Johengen, Thomas H; Vanderploeg, Henry A

    2017-01-01

    One approach to improve forecasts of how global change will affect ecosystem processes is to better understand how anthropogenic disturbances alter bacterial assemblages that drive biogeochemical cycles. Species invasions are important contributors to global change, but their impacts on bacterial community ecology are rarely investigated. Here, we studied direct impacts of invasive dreissenid mussels (IDMs), one of many invasive filter feeders, on freshwater lake bacterioplankton. We demonstrated that direct effects of IDMs reduced bacterial abundance and altered assemblage composition by preferentially removing larger and particle-associated bacteria. While this increased the relative abundances of many free-living bacterial taxa, some were susceptible to filter feeding, in line with efficient removal of phytoplankton cells of <2 μm. This selective removal of particle-associated and larger bacteria by IDMs altered inferred bacterial functional group representation, defined by carbon and energy source utilization. Specifically, we inferred an increased relative abundance of chemoorganoheterotrophs predicted to be capable of rhodopsin-dependent energy generation. In contrast to the few previous studies that have focused on the longer-term combined direct and indirect effects of IDMs on bacterioplankton, our study showed that IDMs act directly as a biological disturbance to which freshwater bacterial assemblages are sensitive. The negative impacts on particle-associated bacteria, which have been shown to be more active than free-living bacteria, and the inferred shifts in functional group representation raise the possibility that IDMs may directly alter bacterially mediated ecosystem functions. IMPORTANCE Freshwater bacteria play fundamental roles in global elemental cycling and are an intrinsic part of local food webs. Human activities are altering freshwater environments, and much has been learned regarding the sensitivity of bacterial assemblages to a variety of

  4. High-speed optical feeder-link system using adaptive optics

    Science.gov (United States)

    Arimoto, Yoshinori; Hayano, Yutaka; Klaus, Werner

    1997-05-01

    We propose a satellite laser communication system between a ground station and a geostationary satellite, named high- speed optical feeder link system. It is based on the application of (a) high-speed optical devices, which have been developed for ground-based high-speed fiber-optic communications, and (b) the adaptive optics which compensates wavefront distortions due to atmospheric turbulences using a real time feedback control. A link budget study shows that a system with 10-Gbps bit-rate are available assuming the state-of-the-art device performance of the Er-doped fiber amplifier. We further discuss preliminary measurement results of the atmospheric turbulence at the telescope site in Tokyo, and present current study on the design of the key components for the feeder-link laser transceiver.

  5. The effects of automated scatter feeders on captive grizzly bear activity budgets.

    Science.gov (United States)

    Andrews, Nathan L P; Ha, James C

    2014-01-01

    Although captive bears are popular zoo attractions, they are known to exhibit high levels of repetitive behaviors (RBs). These behaviors have also made them particularly popular subjects for welfare research. To date, most research on ursid welfare has focused on various feeding methods that seek to increase time spent searching for, extracting, or consuming food. Prior research indicates an average of a 50% reduction in RBs when attempts are successful and, roughly, a 50% success rate across studies. This research focused on decreasing time spent in an RB while increasing the time spent active by increasing time spent searching for, extracting, and consuming food. The utility of timed, automated scatter feeders was examined for use with captive grizzly bears (Ursis arctos horribilis). Findings include a significant decrease in time spent in RB and a significant increase in time spent active while the feeders were in use. Further, the bears exhibited a wider range of behaviors and a greater use of their enclosure.

  6. Depletion of the ozone layer: consequences for non-infectious human diseases

    International Nuclear Information System (INIS)

    Bentham, G.

    1993-01-01

    Stratospheric ozone depletion threatens to increase exposure to ultraviolet (UV) radiation which is known to be a factor in a number of diseases. There is little doubt that cumulative exposure to UV radiation is important in the aetiology of non-melanoma skin cancers. Evidence is also strong for a link with cutaneous malignant melanoma, although here it appears to be intermittent intense exposure that is most damaging. More controversial is the view that exposure to solar radiation is a significant factor in ocular damage, particularly in the formation of cataracts. Earlier studies pointing to such an effect have been criticized and alternative aetiological hypotheses have been proposed. However, other studies do show an effect of UV exposure on cortical cataract. Concern is also growing that UV may be capable of activating viruses and have immunological effects that might exacerbate infectious disease. Very worrying is the possibility that UV exposure can activate the human immunodeficiency virus which might accelerate the onset AIDS. Any such health effects that have been observed in human populations are the result of exposure to existing, naturally occurring levels of UV radiation. There is, therefore, great concern about the possible exacerbation of these impacts as a result of increased exposure to UV radiation associated with stratospheric ozone depletion. However, any assessment of the nature and scale of such impacts on human health has to deal with several major problems and these are the focus of this paper. There are uncertainties about recent trends in stratospheric ozone and problems in the prediction of future changes

  7. Cholinergic Modulation of Cortical Microcircuits Is Layer-Specific: Evidence from Rodent, Monkey and Human Brain

    Directory of Open Access Journals (Sweden)

    Joshua Obermayer

    2017-12-01

    Full Text Available Acetylcholine (ACh signaling shapes neuronal circuit development and underlies specific aspects of cognitive functions and behaviors, including attention, learning, memory and motivation. During behavior, activation of muscarinic and nicotinic acetylcholine receptors (mAChRs and nAChRs by ACh alters the activation state of neurons, and neuronal circuits most likely process information differently with elevated levels of ACh. In several brain regions, ACh has been shown to alter synaptic strength as well. By changing the rules for synaptic plasticity, ACh can have prolonged effects on and rearrange connectivity between neurons that outlasts its presence. From recent discoveries in the mouse, rat, monkey and human brain, a picture emerges in which the basal forebrain (BF cholinergic system targets the neocortex with much more spatial and temporal detail than previously considered. Fast cholinergic synapses acting on a millisecond time scale are abundant in the mammalian cerebral cortex, and provide BF cholinergic neurons with the possibility to rapidly alter information flow in cortical microcircuits. Finally, recent studies have outlined novel mechanisms of how cholinergic projections from the BF affect synaptic strength in several brain areas of the rodent brain, with behavioral consequences. This review highlights these exciting developments and discusses how these findings translate to human brain circuitries.

  8. Economic Contribution of Regional Feeder Ports to The Local Economy In Indonesia

    Directory of Open Access Journals (Sweden)

    Ibnu Syabri

    2017-07-01

    Full Text Available Indonesia regional feeder ports’ main function is to serve marine transport activities between regency/city in a province in limited quantities. The intention of the government to make marine transportation as the backbone of national logistic transportation system puts these ports to an important position, as suppliers for the main and/or collector ports and as goods distribution centers for the region from the bigger ports. Not only as a provider of accessibility between regions, regional feeder ports should be seen as an investation to boost regional economy. This study aims to explain the influences of regional feeder ports on regency/city economy, based on the port types: (1 cargo ports, and (2 cargo & passengers ports. Results showed that both types of ports have positive influences on the regency/city economy, although it is not related to region’s economic base sector. Cargo ports which are mainly located on west area of Indonesia, supports the region’s economy more than cargo & passenger ports which are mainly located on the east.

  9. Resolving the architecture of monogenetic feeder systems from exposures of extinct volcanic fields

    Science.gov (United States)

    Muirhead, J.; Van Eaton, A. R.; Re, G.; White, J. D. L.; Ort, M. H.

    2016-12-01

    Monogenetic volcanic fields pose hazards to a number of major cities worldwide. During an eruption, the evolution of the intrusive feeder network modulates eruption behavior and location, as well as the warning signs of impending activity. However, historical examples of monogenetic eruptions are rare, particularly those monitored with the modern tools required to constrain the geometry and interconnectivity of subsurface intrusive feeders (e.g., InSAR, GPS). Geologic exposures in extinct fields around the Colorado Plateau provide clues to the geometry of shallow intrusions (<1000 m depth) that feed monogenetic volcanoes. We present field- and satellite-based observations of exposed intrusions in the Hopi Buttes volcanic field (Arizona), which reveal that many eruptions were fed by interconnected dike-sill systems. Results from the Hopi Buttes show that volcanic cone alignment studies are biased to the identification of dike intrusions, and thereby neglect the important contributions of sills to shallow feeder systems. For example, estimates of intruded volumes in fields exhumed by uplift and erosion in Utah and Arizona show that sills make up 30 - 92% of the shallow intruded volume within 1000 m of the paleosurface. By transporting magma toward and away from eruptive conduits, these sills likely played a role in modulating eruption styles (e.g., explosive vs effusive) and controlling lateral vent migrations. Sill transitions at Hopi Buttes would have produced detectable surface uplifts, and illustrate the importance of geological studies for informing interpretations of geodetic and seismological data during volcanic crises.

  10. Manufacture and test of prototype water pipe chase barrier in ITER Magnet Feeder system

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Kun, E-mail: lukun@ipp.ac.cn [Institute of Plasma Physics, Shushan Hu Road 350, Hefei, Anhui (China); Wen, Xinjie; Liu, Chen; Song, Yuntao [Institute of Plasma Physics, Shushan Hu Road 350, Hefei, Anhui (China); Niu, Erwu [ITER China, 15B Fuxing Road, Beijing 100862 (China); Gung, Chenyu; Su, Man [ITER Organization, Route de Vinon-sur-Verdon – CS 90046, 13067 St Paul-lez-Durance Cedex (France)

    2016-11-01

    The Magnet Feeder system in the International Thermonuclear Experimental Reactor (ITER) deploys electrical currents and supercritical helium to the superconducting magnets and the magnet diagnostic signals to the operators. In the current design, the feeders located in the upper L3 level of the Tokamak gallery penetrate the Tokamak coolant water system vault, the biological shield and the cryostat. As a secondary confinement to contain the activated coolant water in the vault in the case of water pipe burst accident, a water barrier is welded between the penetration in the water pipe chase outer wall and the mid-plane of the vacuum jacket of the Feeder Coil Terminal Box (CTB). A thin-wall stainless steel diaphragm with an omega shape profile is welded around the CTB as the water barrier to endure 2 bar hydraulic pressure. In addition, the barrier is designed as a flexible compensator to withstand a maximum of 15 mm of axial displacement of the CTB in case of helium leak accident without failure. This paper presents the detail configuration, the manufacturing and assembly processes of the water barrier. Test results of the prototype water barrier under simulated accident conditions are also reported. Successful qualification of the design and manufacturing process of the water barrier lays a good foundation for the series production of this subsystem.

  11. RNA sequencing of the human milk fat layer transcriptome reveals distinct gene expression profiles at three stages of lactation.

    Directory of Open Access Journals (Sweden)

    Danielle G Lemay

    Full Text Available Aware of the important benefits of human milk, most U.S. women initiate breastfeeding but difficulties with milk supply lead some to quit earlier than intended. Yet, the contribution of maternal physiology to lactation difficulties remains poorly understood. Human milk fat globules, by enveloping cell contents during their secretion into milk, are a rich source of mammary cell RNA. Here, we pair this non-invasive mRNA source with RNA-sequencing to probe the milk fat layer transcriptome during three stages of lactation: colostral, transitional, and mature milk production. The resulting transcriptomes paint an exquisite portrait of human lactation. The resulting transcriptional profiles cluster not by postpartum day, but by milk Na:K ratio, indicating that women sampled during similar postpartum time frames could be at markedly different stages of gene expression. Each stage of lactation is characterized by a dynamic range (10(5-fold in transcript abundances not previously observed with microarray technology. We discovered that transcripts for isoferritins and cathepsins are strikingly abundant during colostrum production, highlighting the potential importance of these proteins for neonatal health. Two transcripts, encoding β-casein (CSN2 and α-lactalbumin (LALBA, make up 45% of the total pool of mRNA in mature lactation. Genes significantly expressed across all stages of lactation are associated with making, modifying, transporting, and packaging milk proteins. Stage-specific transcripts are associated with immune defense during the colostral stage, up-regulation of the machinery needed for milk protein synthesis during the transitional stage, and the production of lipids during mature lactation. We observed strong modulation of key genes involved in lactose synthesis and insulin signaling. In particular, protein tyrosine phosphatase, receptor type, F (PTPRF may serve as a biomarker linking insulin resistance with insufficient milk supply. This

  12. Fabrication of corneal epithelial cell sheets maintaining colony-forming cells without feeder cells by oxygen-controlled method.

    Science.gov (United States)

    Nakajima, Ryota; Takeda, Shizu

    2014-01-01

    The use of murine 3T3 feeder cells needs to be avoided when fabricating corneal epithelial cell sheets for use in treating ocular surface diseases. However, the expression level of the epithelial stem/progenitor cell marker, p63, is down-regulated in feeder-free culture systems. In this study, in order to fabricate corneal epithelial cell sheets that maintain colony-forming cells without using any feeder cells, we investigated the use of an oxygen-controlled method that was developed previously to fabricate cell sheets efficiently. Rabbit limbal epithelial cells were cultured under hypoxia (1-10% O2) and under normoxia during stratification after reaching confluence. Multilayered corneal epithelial cell sheets were fabricated using an oxygen-controlled method, and immunofluorescence analysis showed that cytokeratin 3 and p63 was expressed in appropriate localization in the cell sheets. The colony-forming efficiency of the cell sheets fabricated by the oxygen-controlled method without feeder cells was significantly higher than that of cell sheets fabricated under 20% O2 without feeder cells. These results indicate that the oxygen-controlled method has the potential to achieve a feeder-free culture system for fabricating corneal epithelial cell sheets for corneal regeneration. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Martian Surface Boundary Layer Characterization: Enabling Environmental Data for Science, Engineering and Human Exploration

    Science.gov (United States)

    England, C.

    2000-01-01

    For human or large robotic exploration of Mars, engineering devices such as power sources will be utilized that interact closely with the Martian environment. Heat sources for power production, for example, will use the low ambient temperature for efficient heat rejection. The Martian ambient, however, is highly variable, and will have a first order influence on the efficiency and operation of all large-scale equipment. Diurnal changes in temperature, for example, can vary the theoretical efficiency of power production by 15% and affect the choice of equipment, working fluids, and operating parameters. As part of the Mars Exploration program, missions must acquire the environmental data needed for design, operation and maintenance of engineering equipment including the transportation devices. The information should focus on the variability of the environment, and on the differences among locations including latitudes, altitudes, and seasons. This paper outlines some of the WHY's, WHAT's and WHERE's of the needed data, as well as some examples of how this data will be used. Environmental data for engineering design should be considered a priority in Mars Exploration planning. The Mars Thermal Environment Radiator Characterization (MTERC), and Dust Accumulation and Removal Technology (DART) experiments planned for early Mars landers are examples of information needed for even small robotic missions. Large missions will require proportionately more accurate data that encompass larger samples of the Martian surface conditions. In achieving this goal, the Mars Exploration program will also acquire primary data needed for understanding Martian weather, surface evolution, and ground-atmosphere interrelationships.

  14. Comparative abundance and distribution of major filter-feeders in the Antarctic pelagic zone

    Science.gov (United States)

    Voronina, N. M.

    1998-11-01

    The filter-feeding plankton, herbivorous copepods, salps and euphausiids, form the basic level of metazoans in the Antarctic pelagic trophic web. This paper sets out to determine the comparative share of these taxonomic groups in the total biomass and annual production. Their most abundant representatives, four copepod species ( Calanus propinquus, Calanoides acutus, Rhincalanus gigas and Metridia gerlachei), all salps and krill Euphausia superba were studied. For the first two groups net samples from six Russian expeditions in different sectors of the Antarctic were used. In total 752 samples from 118 stations were considered. The mean fresh biomass of filter-feeding copepods in the 0-1500 m layer was 18.0 g m -2 and in the entire Antarctic 576 10 6 t. The biomass of salps in comparatively restricted rich regions exceeded 500 g m -2 and in the remaining area was 1.2±0.8 g m -2, giving a total quantity of 882 10 6 t. The krill abundance estimation was based on published data, using a map of its quantitative distribution compiled from commercial trawling made by Soviet fishing and scientific ships during 17 seasons [Parfenovich, S.S., 1980. O zakonomernostyakh razmeshcheniya i regionalnoi differentsiatsii mestoskoplenii krilya v Yuzhnom Okeane. VNIRO, Moskva, in Russian.]. Three main zones based on commercial characteristics were determined by this author: (1) zone of regular occurrence of dense concentrations; (2) zone of rare occurrence of concentrations; (3) zone of low-abundance dispersed krill. All available data on E. superba biomass in the Antarctic were grouped together according to these zones and their means were calculated. The biomass of krill was found to be 60.1±11.2, 3.3±1.3 and 0.8±0.4 g m -2 fresh mass in zones 1, 2 and 3, respectively, with a total of 272 10 6 t. All estimates are compared with the literature data and their validity is discussed. For the annual production determinations the obtained biomass characteristics were multiplied by

  15. A defined, feeder-free, serum-free system to generate in vitro hematopoietic progenitors and differentiated blood cells from hESCs and hiPSCs.

    Directory of Open Access Journals (Sweden)

    Giorgia Salvagiotto

    2011-03-01

    Full Text Available Human ESC and iPSC are an attractive source of cells of high quantity and purity to be used to elucidate early human development processes, for drug discovery, and in clinical cell therapy applications. To efficiently differentiate pluripotent cells into a pure population of hematopoietic progenitors we have developed a new 2-dimensional, defined and highly efficient protocol that avoids the use of feeder cells, serum or embryoid body formation. Here we showed that a single matrix protein in combination with growth factors and a hypoxic environment is sufficient to generate from pluripotent cells hematopoietic progenitors capable of differentiating further in mature cell types of different lineages of the blood system. We tested the differentiation method using hESCs and 9 iPSC lines generated from different tissues. These data indicate the robustness of the protocol providing a valuable tool for the generation of clinical-grade hematopoietic cells from pluripotent cells.

  16. A three-layer immunoradiometric assay for determination of IgG subclass antibodies in Human Sera (''IgG subclass RAST'')

    International Nuclear Information System (INIS)

    Djurup, R.; Soendergaard, I.; Weeke, B.; University of Copenhagen, Denmark); Magnusson, C.G.M.

    1984-01-01

    We report the development of a three-layer immunoradiometric assay (TIRA) for measurement of IgG antibodies of all four subclasses in human sera. The first layer consists of diluted human serum, the second layer is monoclonal mouse antibodies to human IgG subclasses, and the third layer is 125 I-labelled rabbit anti-mouse IgG. Monoclonal anti-IgGI, anti-IgG3 and anti-IgG4 reacted only with their complementary IgG subclass, whereas the anti-IgG2 showed slight cross-reactivity to immunoglobins of other subclasses and classes and to light chain proteins. The observed cross-reactivity was found to be without importance, when the TIRA was applied to measurement of IgG subclass antibodies. Equipotency was established by use of appropriate dilutions of the monoclonal antibodies, and the assay was calibrated by use of human reference serum. The TIRA therefore permits reliable inter-individual and intra-individual comparisons of the IgG antibody response in all four subclasses. Non-specific binding obtained with pooled normal human serum was below 0.33%. Inter-assay coefficient of variation was between 18 and 27%. The TIRA was applied to measurement of IgG subclass antibodies to timothy grass pollen in sera from grass pollen allergies undergoing immunotherapy. (author)

  17. Generation of a human induced pluripotent stem cell line (MUSIi001-A from caesarean section scar fibroblasts using Sendai viral vectors

    Directory of Open Access Journals (Sweden)

    Methichit Wattanapanitch

    2018-03-01

    Full Text Available We generated a human induced pluripotent stem cell (iPSC line from caesarean section scar fibroblasts of a 33-year-old healthy woman using transgene-free Sendai viral vectors under feeder-free condition. The established iPSC line, designated as MUSIi001-A, exhibited a normal karyotype, expressed pluripotent markers, differentiated into cells of three embryonic germ layers. Further analyses showed that the Sendai viral genome was absent at passage 25. The MUSIi001-A line can serve as a control for studying developmental biology and phenotypic comparison with disease-specific iPSCs.

  18. Modelling and validation of diffuse reflectance of the adult human head for fNIRS: scalp sub-layers definition

    Science.gov (United States)

    Herrera-Vega, Javier; Montero-Hernández, Samuel; Tachtsidis, Ilias; Treviño-Palacios, Carlos G.; Orihuela-Espina, Felipe

    2017-11-01

    Accurate estimation of brain haemodynamics parameters such as cerebral blood flow and volume as well as oxygen consumption i.e. metabolic rate of oxygen, with funcional near infrared spectroscopy (fNIRS) requires precise characterization of light propagation through head tissues. An anatomically realistic forward model of the human adult head with unprecedented detailed specification of the 5 scalp sublayers to account for blood irrigation in the connective tissue layer is introduced. The full model consists of 9 layers, accounts for optical properties ranging from 750nm to 950nm and has a voxel size of 0.5mm. The whole model is validated comparing the predicted remitted spectra, using Monte Carlo simulations of radiation propagation with 108 photons, against continuous wave (CW) broadband fNIRS experimental data. As the true oxy- and deoxy-hemoglobin concentrations during acquisition are unknown, a genetic algorithm searched for the vector of parameters that generates a modelled spectrum that optimally fits the experimental spectrum. Differences between experimental and model predicted spectra was quantified using the Root mean square error (RMSE). RMSE was 0.071 +/- 0.004, 0.108 +/- 0.018 and 0.235+/-0.015 at 1, 2 and 3cm interoptode distance respectively. The parameter vector of absolute concentrations of haemoglobin species in scalp and cortex retrieved with the genetic algorithm was within histologically plausible ranges. The new model capability to estimate the contribution of the scalp blood flow shall permit incorporating this information to the regularization of the inverse problem for a cleaner reconstruction of brain hemodynamics.

  19. Meta-analysis on the effects of the physical environment, animal traits, feeder and feed characteristics on the feeding behaviour and performance of growing-finishing pigs.

    Science.gov (United States)

    Averós, X; Brossard, L; Dourmad, J Y; de Greef, K H; Edwards, S A; Meunier-Salaün, M C

    2012-08-01

    A meta-analysis, using information from 45 experiments on growing-finishing pigs published in 39 manuscripts, was carried out to determine the simultaneous effects of the physical environment (space allowance, group size, flooring conditions, temperature, presence of enrichment), pig traits (initial body weight (BW) for each studied time interval, sex, genetics), feeder characteristics (water provision within the feeder, feeder design (individual/collective), feeder places/pig, presence of feeder protection) and feed characteristics (feed allowance (ad libitum/restricted), net energy content, crude protein (CP) content), as well as their potential interactions, on the feeding behaviour and performance of growing-finishing pigs. The detrimental effect of low temperature on performance was particularly evident for restricted-fed pigs (P < 0.05). At reduced feeder space allowance, a reduction in the percentage of time spent eating was predicted when increasing initial BW, whereas the opposite was predicted for larger feeder space allowances (P < 0.001). The reduction in visit duration to the feeder in higher BW groups became gradually more important with increasing feeder space allowance (P < 0.01), whereas the increase in the ingestion rate and average daily feed intake (ADFI) with increasing initial BW became smaller with increasing feeder space (P < 0.05). The model predicted a reduction in feed conversion ratio (FCR) with increasing group size (P < 0.05) and floor space allowance (P < 0.01) and on solid floors with or without bedding (P < 0.05). In comparison with other feeders, wet/dry feeders were associated with more frequent but shorter feeder visits (P < 0.05), higher ingestion rates (P < 0.001) and higher ADFI (P < 0.10). The use of protection within individual feeders increased the time spent feeding (P < 0.001), reduced the number of visits per day (P < 0.01), the ingestion rate (P < 0.001) and FCR (P < 0.01) in comparison with other feeder types. Sex

  20. The ROCK inhibitor Y-27632 improves recovery of human embryonic stem cells after fluorescence-activated cell sorting with multiple cell surface markers.

    Directory of Open Access Journals (Sweden)

    Nil Emre

    Full Text Available BACKGROUND: Due to the inherent sensitivity of human embryonic stem cells (hESCs to manipulations, the recovery and survival of hESCs after fluorescence-activated cell sorting (FACS can be low. Additionally, a well characterized and robust methodology for performing FACS on hESCs using multiple-cell surface markers has not been described. The p160-Rho-associated coiled kinase (ROCK inhibitor, Y-27632, previously has been identified as enhancing survival of hESCs upon single-cell dissociation, as well as enhancing recovery from cryopreservation. Here we examined the application of Y-27632 to hESCs after FACS to improve survival in both feeder-dependent and feeder-independent growth conditions. METHODOLOGY/PRINCIPAL FINDINGS: HESCs were sorted using markers for SSEA-3, TRA-1-81, and SSEA-1. Cells were plated after sorting for 24 hours in either the presence or the absence of Y-27632. In both feeder-dependent and feeder-independent conditions, cell survival was greater when Y-27632 was applied to the hESCs after sort. Specifically, treatment of cells with Y-27632 improved post-sort recovery up to four fold. To determine the long-term effects of sorting with and without the application of Y-27632, hESCs were further analyzed. Specifically, hESCs sorted with and without the addition of Y-27632 retained normal morphology, expressed hESC-specific markers as measured by immunocytochemistry and flow cytometry, and maintained a stable karyotype. In addition, the hESCs could differentiate into three germ layers in vitro and in vivo in both feeder-dependent and feeder-independent growth conditions. CONCLUSIONS/SIGNIFICANCE: The application of Y-27632 to hESCs after cell sorting improves cell recovery with no observed effect on pluripotency, and enables the consistent recovery of hESCs by FACS using multiple surface markers. This improved methodology for cell sorting of hESCs will aid many applications such as removal of hESCs from secondary cell types

  1. Handling system for nuclear fuel cans to a fuel pellet feeder

    International Nuclear Information System (INIS)

    Vere, B.; Mathevon, P.

    1985-01-01

    The handling system comprises a first array of conveyors which takes a batch of casings from a delivery rack, alters the spacing between the casings, and delivers them to a vibrating table feeder, a second array of conveyors which readjusts the spacing between casing to its initial value and transfers the casings to a removal rack, and automatic and synchronized control means for ensuring the displacements of casings always in the same direction. The increase of spacing between casings can be used, before feeding, to allow them to be weighed one after the other, and after feeding, for cleaning the end part of fuel cans [fr

  2. Evaluation of the cryogenic mechanical properties of the insulation material for ITER Feeder superconducting joint

    Science.gov (United States)

    Wu, Zhixiong; Huang, Rongjin; Huang, ChuanJun; Yang, Yanfang; Huang, Xiongyi; Li, Laifeng

    2017-12-01

    The Glass-fiber reinforced plastic (GFRP) fabricated by the vacuum bag process was selected as the high voltage electrical insulation and mechanical support for the superconducting joints and the current leads for the ITER Feeder system. To evaluate the cryogenic mechanical properties of the GFRP, the mechanical properties such as the short beam strength (SBS), the tensile strength and the fatigue fracture strength after 30,000 cycles, were measured at 77K in this study. The results demonstrated that the GFRP met the design requirements of ITER.

  3. Research on communication system of underground safety management based on leaky feeder cable

    Institute of Scientific and Technical Information of China (English)

    CHEN Jian-hong; ZHANG Tao; CHENG Yun-cai; ZHANG Han

    2007-01-01

    According to the current working status of underground safety management and production scheduling, the importance and existed problem of underground mine radio communication were summarized, and the basic principle and classification of leaky feeder cable were introduced and the characteristics of cable were analyzed specifically in depth, and the application model of radio communication system for underground mine safety management was put forward. Meanwhile, the research explanation of the system component, function and evaluation was provided. The discussion result indicates that communication system of underground mine safety management which is integrated two-way relay amplifier and other equipment has many communication functions, and underground mine mobile communication can be achieved well.

  4. The Linehaul-Feeder Vehicle Routing Problem with Virtual Depots and Time Windows

    Directory of Open Access Journals (Sweden)

    Huey-Kuo Chen

    2011-01-01

    Full Text Available This paper addresses the linehaul-feeder vehicle routing problem with virtual depots and time windows (LFVRPTW. Small and large vehicles deliver services to customers within time constraints; small vehicles en route may reload commodities from either the physical depot or from the larger vehicle at a virtual depot before continuing onward. A two-stage solution heuristic involving Tabu search is proposed to solve this problem. The test results show that the LFVRPTW performs better than the vehicle routing problem with time windows in terms of both objective value and the number of small vehicles dispatched.

  5. A New Optimization Framework To Solve The Optimal Feeder Reconfiguration And Capacitor Placement Problems

    Directory of Open Access Journals (Sweden)

    Mohammad-Reza Askari

    2015-07-01

    Full Text Available Abstract This paper introduces a new stochastic optimization framework based bat algorithm BA to solve the optimal distribution feeder reconfiguration DFR as well as the shunt capacitor placement and sizing in the distribution systems. The objective functions to be investigated are minimization of the active power losses and minimization of the total network costs an. In order to consider the uncertainties of the active and reactive loads in the problem point estimate method PEM with 2m scheme is employed as the stochastic tool. The feasibility and good performance of the proposed method are examined on the IEEE 69-bus test system.

  6. Modeling and Control of Low Voltage Flexible Units for Enhanced Operation of Distribution Feeders

    DEFF Research Database (Denmark)

    Raboni, Pietro; Hu, Weihao; Chaudhary, Sanjay

    2013-01-01

    In some networks Distributed Generators (DGs) are phasing out conventional power plants in terms of power production but still large efforts are required for providing ancillary services. In this paper the usage of fast response units like a Micro Turbines (MT) and a stationary Electric Vehicle...... Battery (EVB) is proposed for providing primary regulation in grid connected mode and for hierarchically manage an islanded LV distribution feeder. The unit models are described and a novel EVB model directly based on manufacturer’s data is proposed and evaluated comparing its performances with Sim...

  7. Human mesenchymal stem cells derived from limb bud can differentiate into all three embryonic germ layers lineages.

    Science.gov (United States)

    Jiao, Fei; Wang, Juan; Dong, Zhao-Lun; Wu, Min-Juan; Zhao, Ting-Bao; Li, Dan-Dan; Wang, Xin

    2012-08-01

    Mesenchymal stem cells (MSCs) have been isolated from many sources, including adults and fetuses. Previous studies have demonstrated that, compared with their adult counterpart, fetal MSCs with several remarkable advantages may be a better resource for clinical applications. In this study, we successfully isolated a rapidly proliferating cell population from limb bud of aborted fetus and termed them "human limb bud-derived mesenchymal stem cells" (hLB-MSCs). Characteristics of their morphology, phenotype, cell cycle, and differentiation properties were analyzed. These adherent cell populations have a typically spindle-shaped morphology. Flow cytometry analysis showed that hLB-MSCs are positive for CD13, CD29, CD90, CD105, and CD106, but negative for CD3, CD4, CD5, CD11b, CD14, CD15, CD34, CD45, CD45RA, and HLA-DR. The detection of cell cycle from different passages indicated that hLB-MSCs have a similar potential for propagation during long culture in vitro. The most novel finding here is that, in addition to their mesodermal differentiation (osteoblasts and adipocytes), hLB-MSCs can also differentiated into extramesenchymal lineages, such as neural (ectoderm) and hepatic (endoderm) progenies. These results indicate that hLB-MSCs have a high level of plasticity and can differentiate into cell lineages from all three embryonic layers in vitro.

  8. Assessing the role of benthic filter feeders on phytoplankton production in a shellfish farming site: Mont Saint Michel Bay, France

    Science.gov (United States)

    Cugier, Philippe; Struski, Caroline; Blanchard, Michel; Mazurié, Joseph; Pouvreau, Stéphane; Olivier, Frédéric; Trigui, Jihane R.; Thiébaut, Eric

    2010-07-01

    The macrobenthic community of Mont Saint Michel Bay (English Channel, France) is mainly dominated by filter feeders, including cultivated species (oysters and mussels). An ecological model of the bay was developed, coupling a 2D hydro-sedimentary model and two biological models for primary production and filter-feeder filtration. The filter-feeder model includes three cultivated species ( Mytilus edulis, Crassostrea gigas and Ostrea edulis), one invasive species ( Crepidula fornicata) and eight wild native species ( Abra alba, Cerastoderma edule, Glycymeris glycymeris, Lanice conchilega, Macoma balthica, Paphia rhomboides, Sabellaria alveolata, andSpisula ovalis). For cultivated and invasive species, the production of biodeposits was computed to assess their role in restimulating primary production. Chlorophyll a concentrations appeared to be strongly controlled by the filter feeders. When the pressure of each benthic compartment on phytoplankton was estimated separately wild species and the invasive slipper limpet C.fornicata were shown to be key elements in the control of primary production. Conversely, the role of cultivated species, particularly oysters, was weaker. Feedback due to the mineralization of biodeposits also appears to be crucial to fully evaluate the role of filter feeders in primary production.

  9. Effect of portion size and milk flow on the use of a milk feeder and the development of cross-sucking in dairy calves

    DEFF Research Database (Denmark)

    Nielsen, Per Peetz; Jensen, Margit Bak; Halekoh, Ulrich

    2018-01-01

    milk feeder in each pen, and exposed to four milk-feeding treatments in a cross-over design with four periods of 1 week. All four treatments involved a daily allowance of 8. L of whole milk, with variation in the maximum portion size and the rate at which milk entered the teat of the milk feeder......This study aimed to investigate whether reducing the milk flow and increasing the milk portion size of a computer-controlled milk feeder would lead to less cross-sucking and fewer unrewarded feeder visits in dairy calves. Five groups, each with 9 or 10 calves (n = 48), were housed in pens with one...

  10. Mannosides as crucial part of bioactive supports for cultivation of human epidermal keratinocytes without feeder cells

    Czech Academy of Sciences Publication Activity Database

    Labský, Jiří; Dvořánková, B.; Smetana, Karel; Holíková, Z.; Brož, L.; Gabius, H.J.

    2003-01-01

    Roč. 24, č. 5 (2003), s. 863-872 ISSN 0142-9612 R&D Projects: GA ČR GA203/00/1310; GA MŠk LN00A065; GA MZd ND6340 Institutional research plan: CEZ:AV0Z4050913 Keywords : cell therapy * keratinocyte * mannose Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.903, year: 2003

  11. Improvement of the auto wire feeder machine in a de-soldering process

    Directory of Open Access Journals (Sweden)

    Niramon Nonkhukhetkhong

    2016-10-01

    Full Text Available This paper presents the methodology of the de-soldering process for rework of disk drive Head Stack Assembly (HSA units. The auto wire feeder is a machine that generates Tin (Sn on the product. This machine was determined to be one of the major sources of excess Sn on the HSA. The defect rate due to excess Sn is more than 30%, which leads to increased processing time and cost to perform additional cleaning steps. From process analysis, the major causes of excess Sn are as follows: 1 The machine cannot cut the wire all the way into the flux core area; 2 The sizes and types of soldering irons are not appropriate for the unit parts; and, 3 There are variations introduced into the de-soldering process by the workforce. This paper proposes a methodology to address all three of these causes. First, the auto wire feeder machine in the de-solder process will be adjusted in order to cut wires into flux core. Second, the types of equipment and material used in de-soldering will be optimized. Finally, a new standard method for operators, which can be controlled more easily, will be developed in order to reduce defects due to workforce related variation. After these process controls and machine adjustments were implemented, the overall Sn related problems were significantly improved. Sn contamination was reduced by 41% and cycle time was reduced by an average of 15 seconds.

  12. Manufacture and testing of the CTB&SBB thermal shield for the ITER magnet feeder system

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Kun; Liu, Chen; Song, Yuntao; Feng, Hansheng; Ding, Kaizhong, E-mail: kzding@ipp.ac.cn; Wang, Tanbin; Ji, Hui

    2015-10-15

    The system of International Thermonuclear Experimental Reactor (ITER) feeders is responsible for the power, helium cooling, and instrumentation of the magnets of the coil terminal box and S-bend box (CTB&SBB) thermal shield outside the cryostat. An 80-K rectangular Al thermal shield is hung inside the CTB&SBB to reduce the thermal radiation heat loads of 4.5-K helium. The American Society of Interventional Pain Physicians (ASIPP) will supply all the 31 sets of feeders for ITER. A manufactured prototype of CTB&SBB thermal shield is first quality-tested before the commencement of the series production. First, a detailed configuration of the rectangular Al thermal shield is presented in this article. The paper also presents more information on the manufacturing process of the thermal shield, especially the welding process, the procedure for ensuring good weld quality, and the use of a specially designed tool to ensure <5-mm deformation on such a 7.3-m-long thermal shield during welding. In addition, the cold test and results, including the cooling process with 13-bar and 17.5-g/s 80-K He gas, and the temperature distribution on different panels of the thermal shield are presented. The whole process of manufacture and testing lays a good foundation for the series production of the thermal shield.

  13. Photovoltaic Hosting Capacity of Feeders with Reactive Power Control and Tap Changers

    Energy Technology Data Exchange (ETDEWEB)

    Ceylan, Oğuzhan; Paudyal, Sumit; Bhattarai, Bishnu P.; Myers, Kurt S.

    2017-06-01

    This paper proposes an algorithm to determine photovoltaic (PV) hosting capacity of power distribution networks as a function of number of PV injection nodes, reactive power support from the PVs, and the sub-station load tap changers (LTCs). In the proposed method, several minute by minute simulations are run based on randomly chosen PV injection nodes, daily PV output profiles, and daily load profiles from a pool of high-resolution realistic data set. The simulation setup is built using OpenDSS and MATLAB. The performance of the proposed method is investigated in the IEEE 123-node distribution feeder for multiple scenarios. The case studies are performed particularly for one, two, five and ten PV injection nodes, and looking at the maximum voltage deviations. Case studies show that the PV hosting capacity of the 123-node feeder greatly differs with the number of PV injection nodes. We have also observed that the PV hosting capacity increases with reactive power support and higher tap position of sub-station LTC.

  14. Stability-index based method for optimal Var planning in distribution feeders

    International Nuclear Information System (INIS)

    Hamouda, Abdellatif; Zehar, Khaled

    2011-01-01

    Research highlights: → Optimal Var planning is modelled using heuristic methods. → Capacitor sizes and location are determined by a two stage method. → Capacitor locations are determined using nodes stability-indices. → Their sizes are calculated subject to a new constraint on the branches reactive currents. → The solution is fast and leads to better results without over compensation. -- Abstract: The problem of the reactive energy optimal planning can be solved in a fast and efficient way using heuristic techniques. The latter reduce the number of the control variables to be determined and lead to a near global optimal solution. The capacitor appropriate locations are firstly determined by decisive indices then, their optimal sizes are calculated. In this paper a stability-index based method is presented. The nodes stability-indices are calculated for identifying the most sensitive nodes to be candidate for receiving near optimal standard capacitors that, reduce the feeder power losses, improve the voltage profile and maximise the economic saving (objective function). In this multi-objective optimisation problem, the commonly used voltage constraint is substituted by a new constraint on the branch reactive currents. This new constraint, allows overcoming the over compensation phenomenon by setting positive branch reactive currents. The solution is further improved by regulating the source node voltage. The proposed approach has been tested on several feeder examples and its effectiveness has been demonstrated through comparative studies. The obtained results have shown that the proposed approach leads to a promising and feasible solution.

  15. Stability-index based method for optimal Var planning in distribution feeders

    Energy Technology Data Exchange (ETDEWEB)

    Hamouda, Abdellatif, E-mail: a_hamouda1@yahoo.f [QUERE Laboratory, Optics and Mechanics Institut, University Ferhat Abbas, Setif 19000 (Algeria); Zehar, Khaled [QUERE Laboratory, Department of Electrical and Electronics Engineering, University of Bahrain, Isa Town (Bahrain)

    2011-05-15

    Research highlights: {yields} Optimal Var planning is modelled using heuristic methods. {yields} Capacitor sizes and location are determined by a two stage method. {yields} Capacitor locations are determined using nodes stability-indices. {yields} Their sizes are calculated subject to a new constraint on the branches reactive currents. {yields} The solution is fast and leads to better results without over compensation. -- Abstract: The problem of the reactive energy optimal planning can be solved in a fast and efficient way using heuristic techniques. The latter reduce the number of the control variables to be determined and lead to a near global optimal solution. The capacitor appropriate locations are firstly determined by decisive indices then, their optimal sizes are calculated. In this paper a stability-index based method is presented. The nodes stability-indices are calculated for identifying the most sensitive nodes to be candidate for receiving near optimal standard capacitors that, reduce the feeder power losses, improve the voltage profile and maximise the economic saving (objective function). In this multi-objective optimisation problem, the commonly used voltage constraint is substituted by a new constraint on the branch reactive currents. This new constraint, allows overcoming the over compensation phenomenon by setting positive branch reactive currents. The solution is further improved by regulating the source node voltage. The proposed approach has been tested on several feeder examples and its effectiveness has been demonstrated through comparative studies. The obtained results have shown that the proposed approach leads to a promising and feasible solution.

  16. Effect of Antimicrobial Dosage Regimen on Salmonella and Escherichia coli Isolates from Feeder Swine▿

    Science.gov (United States)

    Wagner, Bruce A.; Straw, Barbara E.; Fedorka-Cray, Paula J.; Dargatz, David A.

    2008-01-01

    A body of evidence exists that suggests that antimicrobial use in food animals leads to resistance in both pathogenic and commensal bacteria. This study focused on the impact of three different antimicrobial regimes (low-level continuous, pulse, and no antimicrobial) for two antimicrobials (chlortetracycline and tylosin) on the presence of Salmonella spp. and on the prevalence of antimicrobial resistance of both Salmonella spp. and nonspecific Escherichia coli in fecal samples from feeder swine. The prevalence of fecal samples positive for Salmonella spp. significantly decreased between the samples taken at feeder placement compared to samples taken when the animals were close to market weight. Differences in resistance of Salmonella spp. did not appear to be influenced by dosing treatment including the control. Analysis of antimicrobial resistance examining both susceptibility and resistance, as well as MIC outcomes, demonstrated that only resistance to cephalothin increased in E. coli under the pulse chlortetracycline treatment. These results suggest that the dosing regimes examined in this study did not lead to an increase in either the prevalence of Salmonella spp. or the prevalence of antimicrobial resistance in isolates of Salmonella spp. or E. coli. PMID:18223115

  17. Surgical management of dural arteriovenous fistulas with transosseous arterial feeders involving the jugular bulb.

    Science.gov (United States)

    Tirakotai, W; Benes, L; Kappus, C; Sure, U; Farhoud, A; Bien, S; Bertalanffy, H

    2007-01-01

    Dural arteriovenous fistulas located in the vicinity of the jugular foramen are complex vascular malformations and belong to the most challenging skull base lesions to treat. The authors comprehensively analyze multiple features in a series of dural arteriovenous fistulas with transosseous arterial feeders involving the jugular bulb. Four patients who underwent surgery via the transcondylar approach to treat dural arteriovenous fistulas around the jugular foramen were retrospectively reviewed. Previously, endovascular treatment was attempted in all patients. The success of the surgical treatment was examined with postoperative angiography. Complete obliteration of the dural arteriovenous fistulas (DAVFs) was achieved in three patients, and significant flow reduction in one individual. All patients had a good postoperative outcome, and only one experienced mild hypoglossal nerve palsy. Despite extensive bone drilling, an occipitocervical fusion was necessary in only one patient with bilateral lesions. The use of an individually tailored transcondylar approach to treat dural arteriovenous fistulas at the region of the jugular foramen is most effective. This approach allows for complete obliteration of the connecting arterial feeders, and removal of bony structures containing pathological vessels.

  18. Power Hardware-in-the-Loop Evaluation of PV Inverter Grid Support on Hawaiian Electric Feeders

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Austin A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Prabakar, Kumaraguru [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Nagarajan, Adarsh [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Nepal, Shaili [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hoke, Anderson F [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Asano, Marc [Hawaiian Electric Company; Ueda, Reid [Hawaiian Electric Company; Ifuku, Earle [Hawaiian Electric Company

    2017-10-03

    As more grid-connected photovoltaic (PV) inverters become compliant with evolving interconnections requirements, there is increased interest from utilities in understanding how to best deploy advanced grid-support functions (GSF) in the field. One efficient and cost-effective method to examine such deployment options is to leverage power hardware-in-the-loop (PHIL) testing methods, which combine the fidelity of hardware tests with the flexibility of computer simulation. This paper summarizes a study wherein two Hawaiian Electric feeder models were converted to real-time models using an OPAL-RT real-time digital testing platform, and integrated with models of GSF capable PV inverters based on characterization test data. The integrated model was subsequently used in PHIL testing to evaluate the effects of different fixed power factor and volt-watt control settings on voltage regulation of the selected feeders using physical inverters. Selected results are presented in this paper, and complete results of this study were provided as inputs for field deployment and technical interconnection requirements for grid-connected PV inverters on the Hawaiian Islands.

  19. Supervisory control and data acquisition system development for superconducting current feeder system of SST-1

    International Nuclear Information System (INIS)

    Patel, R.; Mahesuria, G.; Gupta, N.C.; Sonara, D.; Panchal, R.; Panchal, P.; Tanna, V.L.; Pradhan, S.

    2014-01-01

    The Current Feeders System (CFS) is essentially an optimized bridge between the power supply at room temperature and Super Conducting Magnet System (SCMS) of the SST-1 machine at 4.5 K.CFS is a complex electrical and cryogenic network which consists of ten pairs of 10 KA rating helium Vapor cooled Conventional Current Leads (VCCLs), superconducting (SC) current feeder and associated components. For the safe and reliable operation of CFS, it is equipped with different physical process parameters measuring instruments like flow, pressure, temperature, level, vacuum, voltage taps and final control element like control valves, heaters, vacuum pumps etc. PLC program is developed in ladder language for acquiring and controlling the process parameters. Independent SCADA applications developed in WonderwareIntouch software for data communication from PLC, front-end Graphical User Interface (GUI), auto-manual interface, real time trends, history trends, events and alarm pages. Time synchronized communication established between CFS control system and Industrial SQL server (InSQL) Historian for centralized storage of CFS process parameters which intern provides the CFS process data to SST-1 central control room. SCADA based data acquisition and data retrieval system is found to be satisfactory during the recent SST-1 cool down experiment. This paper describes the SCADA and PLC application development and their communication to InSQL server. (author)

  20. Enhanced Particle Swarm Optimization-Based Feeder Reconfiguration Considering Uncertain Large Photovoltaic Powers and Demands

    Directory of Open Access Journals (Sweden)

    Ying-Yi Hong

    2014-01-01

    Full Text Available The Kyoto protocol recommended that industrialized countries limit their green gas emissions in 2012 to 5.2% below 1990 levels. Photovoltaic (PV arrays provide clear and sustainable renewable energy to electric power systems. Solar PV arrays can be installed in distribution systems of rural and urban areas, as opposed to wind-turbine generators, which cause noise in surrounding environments. However, a large PV array (several MW may incur several operation problems, for example, low power quality and reverse power. This work presents a novel method to reconfigure the distribution feeders in order to prevent the injection of reverse power into a substation connected to the transmission level. Moreover, a two-stage algorithm is developed, in which the uncertain bus loads and PV powers are clustered by fuzzy-c-means to gain representative scenarios; optimal reconfiguration is then achieved by a novel mean-variance-based particle swarm optimization. The system loss is minimized while the operational constraints, including reverse power and voltage variation, are satisfied due to the optimal feeder reconfiguration. Simulation results obtained from a 70-bus distribution system with 4 large PV arrays validate the proposed method.

  1. A single-cell and feeder-free culture system for monkey embryonic stem cells.

    Science.gov (United States)

    Ono, Takashi; Suzuki, Yutaka; Kato, Yosuke; Fujita, Risako; Araki, Toshihiro; Yamashita, Tomoko; Kato, Hidemasa; Torii, Ryuzo; Sato, Naoya

    2014-01-01

    Primate pluripotent stem cells (PSCs), including embryonic stem cells (ESCs) and induced pluripotent stem cells (iPSCs), hold great potential for research and application in regenerative medicine and drug discovery. To maximize primate PSC potential, a practical system is required for generating desired functional cells and reproducible differentiation techniques. Much progress regarding their culture systems has been reported to date; however, better methods would still be required for their practical use, particularly in industrial and clinical fields. Here we report a new single-cell and feeder-free culture system for primate PSCs, the key feature of which is an originally formulated serum-free medium containing FGF and activin. In this culture system, cynomolgus monkey ESCs can be passaged many times by single-cell dissociation with traditional trypsin treatment and can be propagated with a high proliferation rate as a monolayer without any feeder cells; further, typical PSC properties and genomic stability can be retained. In addition, it has been demonstrated that monkey ESCs maintained in the culture system can be used for various experiments such as in vitro differentiation and gene manipulation. Thus, compared with the conventional culture system, monkey ESCs grown in the aforementioned culture system can serve as a cell source with the following practical advantages: simple, stable, and easy cell maintenance; gene manipulation; cryopreservation; and desired differentiation. We propose that this culture system can serve as a reliable platform to prepare primate PSCs useful for future research and application.

  2. Eddy current array probe for detection of surface breaking cracks in the extrados of feeder bends

    International Nuclear Information System (INIS)

    Obrutsky, L.S.; Cassidy, R.A.; Chaplin, K.; Martin, P.; Bureau, J.F.

    2006-01-01

    A new eddy current array probe has been implemented as a straightforward and promising technique for detection of outer diameter (OD) surface-breaking cracks on the extrados of feeder bends. The design is based on previous work performed at AECL, which had demonstrated that eddy current probes with laterally displaced transmit-receive coils can overcome some of the limitations of inspecting ferritic steel components for surface-breaking cracks. The Feeder Integrity Joint Program-CANDU Owners Group Inc. (FIJP-COG) Non-Destructive Evaluation (NDE) Team members commissioned AECL to work in collaboration with the probe manufacturer ZETEC, to develop a field usable eddy current array probe. The objective was to acquire a technique with the following capabilities: fast scanning non-contact inspection technique for surface breaking discontinuities; full inspection of the bend extrados OD surface in a single scan; ability to inspect first and second bends with similar settings and capabilities; permanent record for future reference; axial and circumferential crack detection in a single scan; capability to detect OD surface-breaking cracks, which can provide additional information to that provided by ultrasonic testing (UT) for flaw characterization, and detection threshold: Surface breaking cracks equivalent to a 0.5 mm deep, 10 mm long EDM notch located on the OD of the bend extrados. This paper discusses the basis for probe design, summarizes the experimental work to evaluate probe capabilities and analyzes the results from the field trial. (author)

  3. Eddy current array probe for detection of surface breaking cracks in the extrados of feeder bends

    Energy Technology Data Exchange (ETDEWEB)

    Obrutsky, L.S.; Cassidy, R.A.; Chaplin, K. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada)]. E-mail: obrutskyl@aecl.ca; Martin, P. [NB Power, Point Lepreau NGS, Point Lepreau, New Brunswick (Canada)]. E-mail: PMartin@nbpower.com; Bureau, J.F. [Zetec, Quebec, Quebec (Canada)]. E-mail: jean-francois.bureau@zetec.com

    2006-07-01

    A new eddy current array probe has been implemented as a straightforward and promising technique for detection of outer diameter (OD) surface-breaking cracks on the extrados of feeder bends. The design is based on previous work performed at AECL, which had demonstrated that eddy current probes with laterally displaced transmit-receive coils can overcome some of the limitations of inspecting ferritic steel components for surface-breaking cracks. The Feeder Integrity Joint Program-CANDU Owners Group Inc. (FIJP-COG) Non-Destructive Evaluation (NDE) Team members commissioned AECL to work in collaboration with the probe manufacturer ZETEC, to develop a field usable eddy current array probe. The objective was to acquire a technique with the following capabilities: fast scanning non-contact inspection technique for surface breaking discontinuities; full inspection of the bend extrados OD surface in a single scan; ability to inspect first and second bends with similar settings and capabilities; permanent record for future reference; axial and circumferential crack detection in a single scan; capability to detect OD surface-breaking cracks, which can provide additional information to that provided by ultrasonic testing (UT) for flaw characterization, and detection threshold: Surface breaking cracks equivalent to a 0.5 mm deep, 10 mm long EDM notch located on the OD of the bend extrados. This paper discusses the basis for probe design, summarizes the experimental work to evaluate probe capabilities and analyzes the results from the field trial. (author)

  4. Design of Two Feeder Three Phase Four Wire Distribution System Utilizing Multi Converter UPQC with Fuzzy Logic Controller

    Directory of Open Access Journals (Sweden)

    Chandra Babu Paduchuri

    2014-01-01

    Full Text Available This paper proposes the instantaneous p-q theory based fuzzy logic controller (FLC for multi converter unified power quality conditioner (MC-UPQC to mitigate power quality issues in two feeders three-phase four-wire distribution systems. The proposed system is extended system of the existing one feeder three-phase four-wire distribution system, which is operated with UPQC. This system is employed with three voltage source converters, which are connected commonly to two feeder distribution systems. The performance of this proposed system used to compensate voltage sag, neutral current mitigation and compensation of voltage and current harmonics under linear and nonlinear load conditions. The neutral current flowing in series transformers is zero in the implementation of the proposed system. The simulation performance analysis is carried out using MATLAB.

  5. Applicability of ANSYS ELBOW290 element for flexibility calculation of tight radius bends on feeder pipes in CANDU reactors

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, X., E-mail: Xuan.Zhang@candu.com [Candu Energy Inc, Mississauga, ON (Canada)

    2015-07-01

    A curved pipe element, ELBOW290, became available in ANSYS 12. This element was developed based on a simplified shell theory, and maintains the ability to capture cross-sectional deformations of elbows. Numerical testing on the applicability of this element for the flexibility calculation of the tight radius bends in CANDU reactors is carried out to determine the usability of this element in completing stress analyses for feeder pipes. Comparisons are made between the ELBOW290 and the shell element for various feeder bend types found in domestic and overseas CANDU reactors. The comparisons show that the ELBOW290 element is suitable for calculating the flexibility of the tight radius bends. (author)

  6. The use of multiple imputation for the accurate measurements of individual feed intake by electronic feeders.

    Science.gov (United States)

    Jiao, S; Tiezzi, F; Huang, Y; Gray, K A; Maltecca, C

    2016-02-01

    Obtaining accurate individual feed intake records is the key first step in achieving genetic progress toward more efficient nutrient utilization in pigs. Feed intake records collected by electronic feeding systems contain errors (erroneous and abnormal values exceeding certain cutoff criteria), which are due to feeder malfunction or animal-feeder interaction. In this study, we examined the use of a novel data-editing strategy involving multiple imputation to minimize the impact of errors and missing values on the quality of feed intake data collected by an electronic feeding system. Accuracy of feed intake data adjustment obtained from the conventional linear mixed model (LMM) approach was compared with 2 alternative implementations of multiple imputation by chained equation, denoted as MI (multiple imputation) and MICE (multiple imputation by chained equation). The 3 methods were compared under 3 scenarios, where 5, 10, and 20% feed intake error rates were simulated. Each of the scenarios was replicated 5 times. Accuracy of the alternative error adjustment was measured as the correlation between the true daily feed intake (DFI; daily feed intake in the testing period) or true ADFI (the mean DFI across testing period) and the adjusted DFI or adjusted ADFI. In the editing process, error cutoff criteria are used to define if a feed intake visit contains errors. To investigate the possibility that the error cutoff criteria may affect any of the 3 methods, the simulation was repeated with 2 alternative error cutoff values. Multiple imputation methods outperformed the LMM approach in all scenarios with mean accuracies of 96.7, 93.5, and 90.2% obtained with MI and 96.8, 94.4, and 90.1% obtained with MICE compared with 91.0, 82.6, and 68.7% using LMM for DFI. Similar results were obtained for ADFI. Furthermore, multiple imputation methods consistently performed better than LMM regardless of the cutoff criteria applied to define errors. In conclusion, multiple imputation

  7. Layer-by-layer assembly of gold nanoparticles and cysteamine on gold electrode for immunosensing of human chorionic gonadotropin at picogram levels

    Energy Technology Data Exchange (ETDEWEB)

    Roushani, Mahmoud, E-mail: mahmoudroushani@yahoo.com [Department of Chemistry, Ilam University, P.O. Box, 69315-516, Ilam (Iran, Islamic Republic of); Valipour, Akram [Department of Chemistry, Ilam University, P.O. Box, 69315-516, Ilam (Iran, Islamic Republic of); Valipour, Mehdi [Department of Chemistry, Payame Noor University, P.O. Box, 19395-3697, Tehran (Iran, Islamic Republic of)

    2016-04-01

    The development of an electrochemical immunosensor for the detection of human chorionic gonadotropin (hCG) is described with a limit of detection as low as 0.3 pg mL{sup −1} in phosphate buffer. In this immunosensor, cysteamine (Cys) and gold nanoparticles (AuNPs) were used to immobilize an anti-hCG monoclonal antibody onto a gold electrode (GE). The structure of AuNPs has been confirmed by EDS, SEM, and TEM analysis. Due to the large specific surface area and excellent electrical conductivity of AuNPs, electron transfer was promoted and the amount of hCG antibody was enhanced significantly. A systematic study on the effects of experimental parameters such as pH, incubation time in the hCG solution and urea solution used for experiments on the binding between the immobilized antibody and hCG has been carried out. Under optimal experimental parameters, differential pulse voltammetry (DPV) signal changes of the [Fe(CN){sub 6}]{sup 3−/4−} are used to detect hCG with two broad linear ranges: 0.001 to 0.2 and 0.2 to 60.7 ng mL{sup −1}. The LOD value proves more sensitive in comparison with previously reported methods. The prepared immunosensor showed high sensitivity and stability. In addition, the immunosensor was successfully used for the determination of hCG in human serum. - Highlights: • AuNPs were used for covalent attachment of anti-body onto GE. • AuNPs joint to GE via Cys, which were similar to electron-transfer tunnel. • A simple method and a sensitive immunosensing for hCG were reported.

  8. Feeders of Free-Roaming Cats: Personal Characteristics, Feeding Practices, and Data on Cat Health and Welfare in an Urban Setting of Israel.

    Science.gov (United States)

    Gunther, Idit; Raz, Tal; Even Zor, Yehonatan; Bachowski, Yuval; Klement, Eyal

    2016-01-01

    Cat feeders serve as an important source of available food for free-roaming cats (FRCs) and can play a central role in providing data on FRC distribution, welfare, and health. Data on cat feeder personalities as well as a better understanding of their feeding practices offer relevance for decision making concerning FRC population control strategies. The current study surveyed 222 FRC feeders who responded to a municipal trap-neuter-return (TNR) campaign in an Israeli central urban setting. The aim of the study was to describe their personal characteristics, feeding practices, and the FRC populations they feed. Feeders were divided into four groups according to the number of cats they claimed to feed per day (group 1: fed up to 5 cats, group 2: fed 6-10 cats, group 3: fed 11-20 cats, and group 4: fed ≥21 cats). Most feeders were women (81%), with a median age of 58 years (range 18-81). The feeders reported an overall feeding of 3337 cats in 342 different feeding locations. Feeders of group 4 comprised 15.31% (n = 34) of all feeders but fed 56% (n = 1869) of the FRC in 37.42% (n = 128) of the feeding locations. "Heavy" feeders (groups 3 and 4) reported that they traveled significantly longer distances in order to feed the cats. Commercial dry food consisted of 90% of the food they provided, with 66% of them feeding once a day, with less food per cat per day than the other feeder groups. Interestingly, "heavy" feeders were usually singles, had on average fewer siblings, a clear preference for owning cats as pets, and lived in lower income neighborhoods. According to the feeders' reports on the FRC populations they fed, 69.7% (2325/3337) cats were neutered and 11.8% (395/3337) were kittens. In addition, they reported that 1.6% (54/3337) of the cats were limping, 2% (67/3337) suffered from a systemic disease, 4% (135/3337) had skin lesions, and 3.9% (130/3337) were suffering from a chronic disability. Abundance of kittens and morbidity rate were

  9. Critical evaluation of gamma-irradiated serum used as feeder in the culture and demonstration of putative nanobacteria and calcifying nanoparticles.

    Directory of Open Access Journals (Sweden)

    Jan Martel

    Full Text Available The culture and demonstration of putative nanobacteria (NB and calcifying nanoparticles (CNP from human and animal tissues has relied primarily on the use of a culture supplement consisting of FBS that had been gamma-irradiated at a dose of 30 kGy (gamma-FBS. The use of gamma-FBS is based on the assumption that this sterilized fluid has been rid entirely of any residual NB/CNP, while it continues to promote the slow growth in culture of NB/CNP from human/animal tissues. We show here that gamma-irradiation (5-50 kGy produces extensive dose-dependent serum protein breakdown as demonstrated through UV and visible light spectrophotometry, fluorometry, Fourier-transformed infrared spectroscopy, and gel electrophoresis. Yet, both gamma-FBS and gamma-irradiated human serum (gamma-HS produce NB/CNP in cell culture conditions that are morphologically and chemically indistinguishable from their normal serum counterparts. Contrary to earlier claims, gamma-FBS does not enhance the formation of NB/CNP from several human body fluids (saliva, urine, ascites, and synovial fluid tested. In the presence of additional precipitating ions, both gamma-irradiated serum (FBS and HS and gamma-irradiated proteins (albumin and fetuin-A retain the inherent dual NB inhibitory and seeding capabilities seen also with their untreated counterparts. By gel electrophoresis, the particles formed from both gamma-FBS and gamma-HS are seen to have assimilated into their scaffold the same smeared protein profiles found in the gamma-irradiated sera. However, their protein compositions as identified by proteomics are virtually identical to those seen with particles formed from untreated serum. Moreover, particles derived from human fluids and cultured in the presence of gamma-FBS contain proteins derived from both gamma-FBS and the human fluid under investigation-a confusing and unprecedented scenario indicating that these particles harbor proteins from both the host tissue and the FBS

  10. A model for strategic selection of feeder management systems: A case study

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Hsing Hung [Faculty of Management and Administration, Macau University of Science and Technology, Avenue Wei Long, Taipa, Macau (China); Lee, Amy H.I. [Department of Industrial Management, Chung Hua University, No. 707, Sec. 2, Wu Fu Rd., Hsinchu 300 (China); Kang, He-Yau [Department of Industrial Engineering and Management, National Chin-Yi University of Technology, 35, Lane 215, Sec. 1, Chung San Rd., Taiping, Taichung 411 (China)

    2010-06-15

    The move to integrating distribution management system (DMS) and feeder management system (FMS) in China is becoming the main trend in recent years, in addition to upgrading and rebuilding existing energy management system (EMS) and DMS. However, with increasing complexity in the social environments along with rapidly changing technologies, how to select a suitable contractor and a FMS project is becoming an important issue for electric power companies. This paper first briefly introduces FMS and then lists its critical success criteria. A model that applies a multi-criteria decision-making (MCDM) method, an analytic network process (ANP) associated with benefits, opportunities, costs and risks (BOCR), is constructed to help power companies to select the most suitable FMS project. (author)

  11. Effect of feeders in 3D modeling of low impedance multilayer CPW transmission line

    Science.gov (United States)

    Zaini, R. I.; Kyabaggu, P. B. K.; Sinulingga, E. P.

    2018-02-01

    Improved characteristics with low dissipation loss MMICs are highly desirable for wireless communications. However, the current industrial MMIC design is mainly based on microstrip concept which suffered from parasitic and unwanted phenomenon especially at higher frequency (>20 GHz). On the other hand, for future wireless technology, higher frequency operation is required and on-wafer microwave characterizations as well as precise modeling of 3D Multilayer CPW components are vital. This project concerns with understanding of the microwave characteristics behavior of Multilayer CPW components in MMIC applications. Feeder effect as unwanted parts in the characteristics has been investigated to determine its relation with the half wavelength resonance of the Multilayer CPW Low Impedance Transmission Line.

  12. A Survey of Pesticide Accumulation in a Specialist Feeder, the Koala (Phascolarctos cinereus).

    Science.gov (United States)

    Marschner, Caroline; Higgins, Damien P; Krockenberger, Mark B

    2017-09-01

    To maintain profitability in Australia's agricultural and urban landscapes pesticides are used throughout the range of koala habitats. The koala is a specialist feeder, reliant on metabolic enzyme capacities to utilise a toxic diet of eucalypt leaves and is potentially prone to adverse effects when xenobiotic interactions between dietary and anthropogenic xenobiotics occur. The aim of this study was to investigate accumulation of frequently used pesticides in wild koalas in 4 areas of New South Wales and Queensland. Liver samples of 57 deceased koalas were collected from care facilities and analysed using a modified QuEChERS extraction method followed by GCMSMS, HRLCMS and LCMSMS. No accumulation of any of the 166 investigated pesticides was found. Data indicate hepatic accumulation of pesticides in this species is uncommon even with close interactions with intensive land use. Despite the lack of hepatic bioaccumulation, this study cannot exclude a direct effect on hepatocellular metabolic pathways.

  13. Complete nutrient content of four species of commercially available feeder insects fed enhanced diets during growth.

    Science.gov (United States)

    Finke, Mark D

    2015-11-01

    Commercially raised feeder insects used to feed captive insectivores are a good source of many nutrients but are deficient in several key nutrients. Current methods used to supplement insects include dusting and gut-loading. Here, we report on the nutrient composition of four species of commercially raised feeder insects fed a special diet to enhance their nutrient content. Crickets, mealworms, superworms, and waxworms were analyzed for moisture, crude protein, fat, ash, acid detergent fiber, total dietary fiber, minerals, amino acids, fatty acids, vitamins, taurine, carotenoids, inositol, and cholesterol. All four species contained enhanced levels of vitamin E and omega 3 fatty acids when compared to previously published data for these species. Crickets, superworms, and mealworms contained β-carotene although using standard conversion factors only crickets and superworms would likely contain sufficient vitamin A activity for most species of insectivores. Waxworms did not contain any detectable β-carotene but did contain zeaxanthin which they likely converted from dietary β-carotene. All four species contained significant amounts of both inositol and cholesterol. Like previous reports all insects were a poor source of calcium and only superworms contained vitamin D above the limit of detection. When compared to the nutrient requirements as established by the NRC for growing rats or poultry, these species were good sources of most other nutrients although the high fat and low moisture content of both waxworms and superworms means when corrected for energy density these two species were deficient in more nutrients than crickets or mealworms. These data show the value of modifying the diet of commercially available insects as they are growing to enhance their nutrient content. They also suggest that for most insectivores properly supplemented lower fat insects such as crickets, or smaller mealworms should form the bulk of the diet. © 2015 The Authors. Zoo Biology

  14. The impact of deprivation on youth violence: a comparison of cities and their feeder towns.

    Science.gov (United States)

    Jones, S J; Sivarajasingam, V; Shepherd, J

    2011-06-01

    66,000 children and adolescents are treated at emergency departments (EDs) in England and Wales each year for assault injury. The aim of this study was to compare adolescent assault injury rates in cities and towns and determine how assault injury varies with deprivation and gender. The study was set in three cities in Wales, UK, and their surrounding towns. Subjects were 11-17 year olds treated for assault injury at one of seven EDs from 1 October 2005 to 30 September 2006. Area of residence (electoral divisions, EDivs) was identified from patient postcode. EDivs were aggregated into deprivation fifths for males and females and cities and towns. Assault injury rates, rate ratios and 95% CIs were calculated. 1472 children and adolescents of 11-17 years old were treated for assault injury. Male city assault injury rates were 14.2/1000 11-17 year olds; and 13.1 in towns. Female city assault injury rates were 6.0; and 5.6 in towns. In the most deprived city areas males had assault injury rates 2.6 times (95% CI 1.85 to 3.59) that of the most affluent, compared with 2.0 times in towns (95% CI 1.39 to 2.86). For females, the most deprived city areas had assault injury rates 5.3 times that of the most affluent (95% CI 2.93 to 9.41), compared with 2.8 times in towns (95% CI 1.47 to 5.28). Injury in youth violence increased with increasing deprivation in cities and their feeder towns. This was true for boys and girls, though rates for boys were consistently higher. This link between assault injury and deprivation was stronger for girls in cities than in feeder towns. Strategies to prevent youth violence need to include improved safeguarding arrangements for girls living in the most deprived city areas.

  15. USULAN PERBAIKAN OPERATION POINT SHEET PADA MESIN FEEDER AIDA 1100 PT. XXX DENGAN MENGGUNAKAN METODE SMED

    Directory of Open Access Journals (Sweden)

    Ary Arvianto

    2012-02-01

    Full Text Available Single Minute Exchange of Die (SMED merupakan salah satu alat lean yang penting untuk mengurangi waste dan meningkatkan fleksibilitas dalam proses manufaktur yang memungkinkan dalam pengurangan ukuran lot dan perbaikan aliran manufaktur. SMED mengurangi waktu non-produktif dengan mempersatukan dan standardisasi operasi dalam pergantian alat, dengan menggunakan teknik sederhana dan aplikasi yang mudah. Namun proses tersebut tidak dapat memberikan hasil yang  spesifik dalam pelaksanaannya, dimana masih dapat dilakukan suatu perbaikan. Untuk mengatasi hal ini, data statistik dan alat-alat teknik industri dapat diintegrasikan dalam pendekatan SMED untuk meningkatkan hasil penerapan SMED. Penerapan pendekatan SMED yang diusulkan diuji untuk mesin feeder didalam industri otomotif PT. XXX. Implementasi ini memungkinkan adanya pengurangan waktu setup, melalui reorganisasi sumber daya internal perusahaan tanpa membutuhkan investasi yang signifikan.   Kata kunci: Lean manufacturing systems, Single Minute Exchange of Die, Quick ChangeOver.     Single Minute Exchange of Die (SMED is one of the essential lean tools to reduce waste and increase flexibility in manufacturing processes that enable the reduction of lot size and improving manufacturing flow. SMED reduces non-productive time by streamlining and standardizing operations in the turn of the tool, using simple techniques and easy application. But the process can not provide a specific result in the implementation, which can still be an improvement. To overcome this, statistical data and tools can be integrated in industrial engineering approaches to improve outcomes SMED SMED implementation. The proposed application of SMED approach was tested for the automotive industry in the feeder machine PT. XXX. This implementation allows for the reduction of setup time, through the reorganization of the company's internal resources without requiring significant investment. Keywords: Lean manufacturing

  16. Feeder-cell-independent culture of the pig-embryonic-stem-cell-derived exocrine pancreatic cell line, PICM-31

    Science.gov (United States)

    The adaptation to feeder-independent growth of a pig embryonic stem cell-derived pancreatic cell line is described. The parental PICM-31 cell line, previously characterized as an exocrine pancreas cell line, was colony-cloned two times in succession resulting in the subclonal cell line, PICM-31A1. P...

  17. 47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. 25.147 Section 25.147 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space...

  18. Surface-engineered substrates for improved human pluripotent stem cell culture under fully defined conditions.

    Science.gov (United States)

    Saha, Krishanu; Mei, Ying; Reisterer, Colin M; Pyzocha, Neena Kenton; Yang, Jing; Muffat, Julien; Davies, Martyn C; Alexander, Morgan R; Langer, Robert; Anderson, Daniel G; Jaenisch, Rudolf

    2011-11-15

    The current gold standard for the culture of human pluripotent stem cells requires the use of a feeder layer of cells. Here, we develop a spatially defined culture system based on UV/ozone radiation modification of typical cell culture plastics to define a favorable surface environment for human pluripotent stem cell culture. Chemical and geometrical optimization of the surfaces enables control of early cell aggregation from fully dissociated cells, as predicted from a numerical model of cell migration, and results in significant increases in cell growth of undifferentiated cells. These chemically defined xeno-free substrates generate more than three times the number of cells than feeder-containing substrates per surface area. Further, reprogramming and typical gene-targeting protocols can be readily performed on these engineered surfaces. These substrates provide an attractive cell culture platform for the production of clinically relevant factor-free reprogrammed cells from patient tissue samples and facilitate the definition of standardized scale-up friendly methods for disease modeling and cell therapeutic applications.

  19. Derivation and characterisation of the human embryonic stem cell lines, NOTT1 and NOTT2.

    Science.gov (United States)

    Priddle, Helen; Allegrucci, Cinzia; Burridge, Paul; Munoz, Maria; Smith, Nigel M; Devlin, Lyndsey; Sjoblom, Cecilia; Chamberlain, Sarah; Watson, Sue; Young, Lorraine E; Denning, Chris

    2010-04-01

    The ability to maintain human embryonic stem cells (hESCs) during long-term culture and yet induce differentiation to multiple lineages potentially provides a novel approach to address various biomedical problems. Here, we describe derivation of hESC lines, NOTT1 and NOTT2, from human blastocysts graded as 3BC and 3CB, respectively. Both lines were successfully maintained as colonies by mechanical passaging on mouse embryonic feeder cells or as monolayers by trypsin-passaging in feeder-free conditions on Matrigel. Undifferentiated cells retained expression of pluripotency markers (OCT4, NANOG, SSEA-4, TRA-1-60 and TRA-1-81), a stable karyotype during long-term culture and could be transfected efficiently with plasmid DNA and short interfering RNA. Differentiation via formation of embryoid bodies resulted in expression of genes associated with early germ layers and terminal lineage specification. The electrophysiology of spontaneously beating NOTT1-derived cardiomyocytes was recorded and these cells were shown to be pharmacologically responsive. Histological examination of teratomas formed by in vivo differentiation of both lines in severe immunocompromised mice showed complex structures including cartilage or smooth muscle (mesoderm), luminal epithelium (endoderm) and neuroectoderm (ectoderm). These observations show that NOTT1 and NOTT2 display the accepted characteristics of hESC pluripotency.

  20. Cone-Beam Computed Tomography (CBCT) Hepatic Arteriography in Chemoembolization for Hepatocellular Carcinoma: Performance Depicting Tumors and Tumor Feeders

    Energy Technology Data Exchange (ETDEWEB)

    Lee, In Joon [National Cancer Center, Department of Radiology (Korea, Republic of); Chung, Jin Wook, E-mail: chungjw@snu.ac.kr; Yin, Yong Hu; Kim, Hyo-Cheol; Kim, Young Il; Jae, Hwan Jun; Park, Jae Hyung [Seoul National University College of Medicine, Seoul National University Hospital, Department of Radiology (Korea, Republic of)

    2015-10-15

    PurposeThis study was designed to analyze retrospectively the performance of cone-beam computed tomography (CBCT) hepatic arteriography in depicting tumors and their feeders and to investigate the related determining factors in chemoembolization for hepatocellular carcinoma (HCC).MethodsEighty-six patients with 142 tumors satisfying the imaging diagnosis criteria of HCC were included in this study. The performance of CBCT hepatic arteriography for chemoembolization per tumor and per patient was evaluated using maximum intensity projection images alone (MIP analysis) or MIP combined with multiplanar reformation images (MIP + MPR analysis) regarding the following three aspects: tumor depiction, confidence of tumor feeder detection, and trackability of tumor feeders. Tumor size, tumor enhancement, tumor location, number of feeders, diaphragmatic motion, portal vein enhancement, and hepatic artery to parenchyma enhancement ratio were regarded as potential determining factors.ResultsTumors were depicted in 125 (88.0 %) and 142 tumors (100 %) on MIP and MIP + MPR analysis, respectively. Imaging performances on MIP and MIP + MPR analysis were good enough to perform subsegmental chemoembolization without additional angiographic investigation in 88 (62.0 %) and 128 tumors (90.1 %) on per-tumor basis and in 43 (50 %) and 73 (84.9 %) on per-patient basis, respectively. Significant determining factors for performance in MIP + MPR analysis on per tumor basis were tumor size (p = 0.030), tumor enhancement (0.005), tumor location (p = 0.001), and diaphragmatic motion (p < 0.001).ConclusionsCBCT hepatic arteriography provided sufficient information for subsegmental chemoembolization by depicting tumors and their feeders in the vast majority of patients. Combined analysis of MIP and MPR images was essential to enhance the performance of CBCT hepatic arteriography.

  1. Flow visualization study of two-phase flow in a single bend outlet feeder pipe of a CANDU reactor

    International Nuclear Information System (INIS)

    Savalaxs, S.-A.; Lister, D.H.; Steward, F.R.

    2005-01-01

    In CANDU reactors, the feeder piping that is used to direct the high-temperature water coolant between the fuel channels and the steam generators is made of carbon steel. Since 1996, several CANDU stations have reported excessive corrosion of their outlet feeders. The first metre is particularity vulnerable because the piping there consists of single or double bends, which have relatively thin walls produced by the bending process. Early studies related the attack to the hydrodynamics of the coolant and verified that it was a type of flow-accelerated corrosion. In order to understand the hydrodynamics of the coolant in the outlet feeders by flow visualization, a full-scale transparent test section simulating the geometry and orientation of an outlet feeder bend with its upstream components was fabricated. The feeder consisted of a 54 mm diameter acrylic pipe with a 73 degree bend. This was connected to the upstream component with an acrylic simulation of a Grayloc flanged fitting. A test loop supplied room temperature water to the test section at flow rates up to 0.019 m3/s. Air could be injected into the water to give a mean volume fraction of up to 0.56. In this preliminary investigation, the size and velocity of air bubbles at different flow conditions and their distribution within the pipe bend were studied. Particular attention was paid to the flow pattern at the inside of the bend, where a CFD (computational fluid dynamics) code - Fluent 6.1-had failed to predict a liquid film in an earlier study. A high-speed digital video camera was used to determine the relation between bubble size and velocity. Such a relation should help to explain the discrepancy in the CFD modelling and provide the basis for accurate predictions of phase distribution in complex geometries at high flow rates. (authors)

  2. Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de La Muerte, Costa Rica

    Directory of Open Access Journals (Sweden)

    Gerardo Avalos

    2012-03-01

    Full Text Available Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis, dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads, and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon. Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of

  3. Derivation of transgene-free human induced pluripotent stem cells from human peripheral T cells in defined culture conditions.

    Directory of Open Access Journals (Sweden)

    Yoshikazu Kishino

    Full Text Available Recently, induced pluripotent stem cells (iPSCs were established as promising cell sources for revolutionary regenerative therapies. The initial culture system used for iPSC generation needed fetal calf serum in the culture medium and mouse embryonic fibroblast as a feeder layer, both of which could possibly transfer unknown exogenous antigens and pathogens into the iPSC population. Therefore, the development of culture systems designed to minimize such potential risks has become increasingly vital for future applications of iPSCs for clinical use. On another front, although donor cell types for generating iPSCs are wide-ranging, T cells have attracted attention as unique cell sources for iPSCs generation because T cell-derived iPSCs (TiPSCs have a unique monoclonal T cell receptor genomic rearrangement that enables their differentiation into antigen-specific T cells, which can be applied to novel immunotherapies. In the present study, we generated transgene-free human TiPSCs using a combination of activated human T cells and Sendai virus under defined culture conditions. These TiPSCs expressed pluripotent markers by quantitative PCR and immunostaining, had a normal karyotype, and were capable of differentiating into cells from all three germ layers. This method of TiPSCs generation is more suitable for the therapeutic application of iPSC technology because it lowers the risks associated with the presence of undefined, animal-derived feeder cells and serum. Therefore this work will lead to establishment of safer iPSCs and extended clinical application.

  4. Effects of alternating and direct electrical current application on the odontoblastic layer in human teeth : an in vitro study

    NARCIS (Netherlands)

    Alwas-Danowska, HM; Huysmans, MCDNJM; Verdonschot, EH

    Aim The aim of this study was to investigate the influence of a low intensity alternating current on the odontoblasts and odontoblast layer and compare this with the effects of a direct current. Methodology Teeth extracted for orthodontic were immersed in physiological saline stabilized with thymol

  5. Field evaluation of cutter and feeder mechanism of chickpea harvester for lentil harvesting

    Directory of Open Access Journals (Sweden)

    S Kamgar

    2016-09-01

    Full Text Available Introduction The main producers of lentil are Canada, India, Nepal and China, respectively and Iran is the ninth producer in the world. The hand pulling is the usual method of lentil harvesting. Use of conventional combine because of short leg varieties, wide combine head in dry land and grain losses by cutter bar vibrations is impossible. So a mechanism should be designed to harvest the lentil plants with minimum damage. This mechanism should be evaluated under different tests of crop and machines such as forward speed (FS, grain moisture content (GMC, different varieties and other parameters. Some researchers studied the effects of GMC (Andrews and et al., 1993; Huitink, 2005; Adisa, 2009; Abdi and Jalali, 2013 and FS on grain losses (Geng et al., 1984; Swapan et al., 2001; Mostafavand and Kamgar, 2014; Hunt, 1995. Field tests were conducted at three levels of FS 1.5, 3 and 4.5 km.h-1; three levels of cutting height (CH 4, 8 and 13 cm and two levels of GMC, 8 and 14% on two varieties of lentils including Flip and Shiraz with three replications. Materials and Methods The feeder and cutter mechanism for chickpea harvesting that was the base design of device which is notched wheel and counter shear, was used. The other components of device were dividers, slat and chain feeders, belt and pulleys, chassis, elevator conveyor and storage. Two split plot design based on a randomized complete design was used to determine the effects of above treatments on lentil losses. Results and Discussion The ANOVA results indicated that the all studied factors; FS of feeder and cutter mechanism, CH and GMC had significant effect on losses of Shiraz variety (P0.05. The ranges of losses of Flip variety at 8% GMC were 8.6 to 10% for FS of 1.5 km.h-1, 9.1 to 10.4% for FS of 3 km.h-1and 10.4 to 11.4% for FS of 4.5 km h-1. These ranges at 14% GMC were 7.9 to 8.9% for FS of 1.5 km.h-1, 8.4 to 9.2% for FS of 3 km.h-1and 8.5 to 10% for FS of 4.5 km h-1. The ranges of

  6. [Effects of prefrontal ablations on the reaction of the active choice of feeder under different probability and value of the reinforcement on dog].

    Science.gov (United States)

    Preobrazhenskaia, L A; Ioffe, M E; Mats, V N

    2004-01-01

    The role of the prefrontal cortex was investigated on the reaction of the active choice of the two feeders under changes value and probability reinforcement. The experiments were performed on 2 dogs with prefrontal ablation (g. proreus). Before the lesions the dogs were taught to receive food in two different feeders to conditioned stimuli with equally probable alimentary reinforcement. After ablation in the inter-trial intervals the dogs were running from the one feeder to another. In the answer to conditioned stimuli for many times the dogs choose the same feeder. The disturbance of the behavior after some times completely restored. In the experiments with competition of probability events and values of reinforcement the dogs chose the feeder with low-probability but better quality of reinforcement. In the experiments with equal value but different probability the intact dogs chose the feeder with higher probability. In our experiments the dogs with prefrontal lesions chose the each feeder equiprobably. Thus in condition of free behavior one of different functions of the prefrontal cortex is the reactions choose with more probability of reinforcement.

  7. Using automated feeders to wean calves fed large amounts of milk according to their ability to eat solid feed.

    Science.gov (United States)

    de Passillé, Anne Marie; Rushen, Jeffrey

    2016-05-01

    Dairy calves weaned off milk at an early age show signs of hunger and can lose weight. We examined whether using automated feeders to wean calves according to individual voluntary solid feed intake reduced the effects of weaning. Female Holstein calves were housed in groups of 5 to 9. All calves were fed 12 L/d milk and ad libitum grain starter and hay from automated feeders immediately after grouping, and were allocated to 3 weaning strategies: (1) early-weaned (EW; n=14): weaning began on d 40, and milk allowance gradually decreased until weaning was complete on d 48; (2) late-weaned (LW; n=14): weaning began on d 80 and was completed on d 89; (3) weaned by starter intake (WSI; n=28): weaning began when calves consumed 200g/d of starter and was completed when the calves consumed 1,400g/d. Each day, the automated feeders recorded quantities of milk, starter, and hay eaten by all calves, as well as the frequency of visits to the milk feeder; we used unrewarded visit frequency as a sign of hunger. Body weights (BW) were recorded weekly. We estimated daily digestible energy (DE) intake for each calf based on the milk, hay, and starter consumed. Average daily gains (ADG) were expressed as percent of BW. For calves in WSI, weaning began at 54.7±18.9 d (mean ± SD) of age, the duration of weaning was 21.1±10.6 d, and weaning ended at 75.8±10.7 d of age. Both LW and WSI calves had better ADG from wk 3 to 13 than EW calves. Calves in the WSI group drank less milk and ate more starter than LW calves but had similar ADG. During the period of weaning, EW calves made more unrewarded visits to the milk feeder than LW and WSI calves. Three EW calves lost weight during weaning, whereas all LW and WSI calves gained weight. Calves differ greatly in when they begin to eat solid feed and how quickly they increase the intake in response to a decrease in milk allowance. An advantage of automated feeders is that calves can be weaned at variable ages depending on their ability and

  8. Challenges associated with the current processes for ultrasonic inspection of CANDU reactor feeder piping

    Energy Technology Data Exchange (ETDEWEB)

    Machowski, C. [Babcock & Wilcox Canada Ltd., Cambridge, Ontario (Canada)

    2012-07-01

    CANDU® PHT Feeder Piping is generally constructed from SA106 Grade B carbon steel, which is known to be susceptible to flow accelerated corrosion when exposed to certain environmental conditions. The configuration of the CANDU reactor promotes thinning of the inside surface of the pipe walls, predominantly at the outlet feeders. Inspection of this piping is currently conducted using ultrasonic techniques and is governed by the requirements established by the CANDU Owners Group (COG). There are many challenges associated with these inspections as a result of the complexity of the reactor piping configuration. Geometrical anomalies on the surface of the pipe and non-circular geometries at the tight radius bends hinder the performance of conventional ultrasonic techniques. This can cause lost signals in areas of interest, which in turn often results in rework in order to satisfy the inspection requirements and justify fitness for service of these components. There are also many inspection sites which have limited access due to physical restrictions on the reactor face; therefore in order to maximize the performance of an inspection campaign, it is paramount that the inspection personnel and the inspection technology be well integrated through training simulations prior to execution. These inspection challenges increase the complexity of the analysis process as ultrasonic signals get distorted and lost as a result of non-circular pipe geometries. In order to ensure a high level of integrity in the analysis results, a conservative process is utilized in which two analysts independently examine the data, and a third analyst reviews their results and submits the final call. A Data Management Software application (DMS) is used to input and store the three analysis results. Another important function of the DMS is to provide a communication link between the different work-groups associated with the inspection activities. The focus of this presentation discusses:

  9. On the preparation of fire-wood splitting machines equipped with feeder devices

    International Nuclear Information System (INIS)

    Jaeaeskelaeinen, M.

    1995-01-01

    As part of the Bionergy research programme, the TTS Institute's Department of Forestry conducted a study on firewood splitting machines manufactured by Bilke Oy and Peurala Oy. The said machines are the first of their kind in Finland to be equipped with a feeder device. The Bilke unit is fed by a conveyor belt arrangement while the Peurala unit is equipped with a feeder roll. In addition, both machine types are equipped with a conveyor belt discharging device (e.g. for discharging split wood directly into a trailer). The Bilke unit can also be operated on extraction racks in the woods as the stems due to be split are fed into it from the side and the conveyor discharges the split wood rearwards into the trailer. The trailer can be hooked onto the splitting unit's draw-hook. At the landing, the Bilke unit was used to split a total of 14.2 m 3 and the Peurala unit 8.0 m 3 of approx. 3-metrelong stems averaging 9 cm in diameter. In addition to this, the Bilke unit was used to split ca. 17 m 3 of 3.5 metre-long stems with on average diameter of ca. 6 cm; the stems were in bunches alongside the extraction racks. The person operating the machines for the purposes of this study was a 27-year- old forest worker. The mean productivity achieved at the landing when using the Bilke unit was 7.7 m 3 while that of the Peurala unit was 5.8 m 3 per effective hour. When operated in the woods, the productivity achieved with the Bilke unit (excluding felling-cross cutting-delimbing-bunching and forest haulage work) was 2.8 m 3 /h. When applying a productivity of 1.7 m 3 for felling-cross cutting- delimbing-bunching work and 5.5. m 3 for forest haulage, the entire harvesting chain's productivity was 0.9 m 3 per effective hour

  10. The effect of space allowance and cage size on laying hens housed in furnished cages, Part II: Behavior at the feeder

    Science.gov (United States)

    Widowski, T. M; Caston, L. J; Casey-Trott, T. M; Hunniford, M. E

    2017-01-01

    Abstract Standards for feeder (a.k.a. feed trough) space allowance (SA) are based primarily on studies in conventional cages where laying hens tend to eat simultaneously, limiting feeder space. Large furnished cages (FC) offer more total space and opportunities to perform a greater variety of behaviors, which may affect feeding behavior and feeder space requirements. Our objective was to determine the effects of floor/feeder SA on behavior at the feeder. LSL-Lite hens were housed in FC equipped with a nest, perches, and a scratch mat. Hens with SA of either 520 cm2 (Low; 8.9 cm feeder space/hen) or 748 cm2 (High; 12.8 cm feeder space/hen) per bird resulted in groups of 40 vs. 28 birds in small FC (SFC) and 80 vs. 55 in large FC (LFC). Chain feeders ran at 0500, 0800, 1100, 1400, and 1700 with lights on at 0500 and off at 1900 hours. Digital recordings of FC were scanned at chain feeder onset and every 15 min for one h after (5 scans × 5 feeding times × 2 d) to count the number of birds with their head in the feeder. All occurrences of aggressive pecks and displacements during 2 continuous 30-minute observations at 0800 h and 1700 h also were counted. Mixed model repeated analyses tested the effects of SA, cage size, and time on the percent of hens feeding, and the frequency of aggressive pecks and displacements. Surprisingly, the percent of birds feeding simultaneously was similar regardless of cage size (LFC: 23.0 ± 0.9%; SFC: 24.0 ± 1.0%; P = 0.44) or SA (Low: 23.8 ± 0.9%; High: 23.3 ± 1.0%; P = 0.62). More birds were observed feeding at 1700 h (35.3 ± 0.1%) than any at other time (P < 0.001). Feeder use differed by cage area (nest, middle, or scratch) over the d (P < 0.001). The frequency of aggressive pecks was low overall and not affected by SA or cage size. Frequency of displacements was also low but greater at Low SA (P = 0.001). There was little evidence of feeder competition at the Low SA in this study. PMID:29050409

  11. Feeders of free-roaming cats: personal characteristics, feeding practices and data on cat health and welfare in an urban setting of Israel

    Directory of Open Access Journals (Sweden)

    Idit eGunther

    2016-03-01

    Full Text Available Cat feeders serve as an important source of available food for free-roaming cats (FRC and can play a central role in providing data on FRC distribution, welfare, and health. Data on cat feeder personalities as well as a better understanding of their feeding practices offer relevance for decision making concerning FRC population control strategies. The current study surveyed 222 FRC feeders who responded to a municipal trap-neuter-return (TNR campaign in an Israeli central urban setting. The aim of the study was to describe their personal characteristics, feeding practices and the FRC populations they feed. Feeders were divided into four groups according to the number of cats they claimed to feed per day (group 1: fed up to five cats; group 2: fed six to 10 cats; group 3: fed 11-20 cats; group 4: fed ≥21 cats. Most feeders were women (81%, with a median age of 58 years (range 18-81. The feeders reported an overall feeding of 3,337 cats in 342 different feeding locations. Feeders of group 4 comprised of 15.31% (n=34 of all feeders, but fed 56% (n=1869 of the FRC in 37.42% (n=128 of the feeding locations. 'Heavy' feeders (groups 3 and 4 reported that they traveled significantly longer distances in order to feed the cats. Commercial dry food consisted of 90% of the food they provided, with 66% of them feeding once a day, with less food per cat per day than the other feeder groups. Interestingly, 'heavy' feeders were usually singles, had on average fewer siblings, a clear preference for owning cats as pets and lived in lower income neighborhoods. According to the feeders' reports on the FRC populations they fed, 69.7% (2325/3337 cats were neutered and 11.8% (395/3337 were kittens. In addition, they reported that 1.6% (54/3337 of the cats were limping, 2% (67/3337 suffered from a systemic disease, 4% (135/3337 had skin lesions, and 3.9% (130/3337 were suffering from a chronic disability. Abundance of kittens and morbidity rate were significantly and

  12. The effect of space allowance and cage size on laying hens housed in furnished cages, Part II: Behavior at the feeder.

    Science.gov (United States)

    Widowski, T M; Caston, L J; Casey-Trott, T M; Hunniford, M E

    2017-09-01

    Standards for feeder (a.k.a. feed trough) space allowance (SA) are based primarily on studies in conventional cages where laying hens tend to eat simultaneously, limiting feeder space. Large furnished cages (FC) offer more total space and opportunities to perform a greater variety of behaviors, which may affect feeding behavior and feeder space requirements. Our objective was to determine the effects of floor/feeder SA on behavior at the feeder. LSL-Lite hens were housed in FC equipped with a nest, perches, and a scratch mat. Hens with SA of either 520 cm2 (Low; 8.9 cm feeder space/hen) or 748 cm2 (High; 12.8 cm feeder space/hen) per bird resulted in groups of 40 vs. 28 birds in small FC (SFC) and 80 vs. 55 in large FC (LFC). Chain feeders ran at 0500, 0800, 1100, 1400, and 1700 with lights on at 0500 and off at 1900 hours. Digital recordings of FC were scanned at chain feeder onset and every 15 min for one h after (5 scans × 5 feeding times × 2 d) to count the number of birds with their head in the feeder. All occurrences of aggressive pecks and displacements during 2 continuous 30-minute observations at 0800 h and 1700 h also were counted. Mixed model repeated analyses tested the effects of SA, cage size, and time on the percent of hens feeding, and the frequency of aggressive pecks and displacements. Surprisingly, the percent of birds feeding simultaneously was similar regardless of cage size (LFC: 23.0 ± 0.9%; SFC: 24.0 ± 1.0%; P = 0.44) or SA (Low: 23.8 ± 0.9%; High: 23.3 ± 1.0%; P = 0.62). More birds were observed feeding at 1700 h (35.3 ± 0.1%) than any at other time (P Feeder use differed by cage area (nest, middle, or scratch) over the d (P feeder competition at the Low SA in this study. © The Author 2017. Published by Oxford University Press on behalf of Poultry Science Association.

  13. Skin layer mechanics

    NARCIS (Netherlands)

    Geerligs, M.

    2010-01-01

    The human skin is composed of several layers, each with an unique structure and function. Knowledge about the mechanical behavior of these skin layers is important for clinical and cosmetic research, such as the development of personal care products and the understanding of skin diseases. Until

  14. Three-layered radio frequency coil arrangement for sodium MRI of the human brain at 9.4 Tesla.

    Science.gov (United States)

    Shajan, G; Mirkes, Christian; Buckenmaier, Kai; Hoffmann, Jens; Pohmann, Rolf; Scheffler, Klaus

    2016-02-01

    A multinuclei imaging setup with the capability to acquire both sodium ((23) Na) and proton ((1) H) signals at 9.4 Tesla is presented. The main objective was to optimize coil performance at the (23) Na frequency while still having the ability to acquire satisfactory (1) H images. The setup consisted of a combination of three radio frequency (RF) coils arranged in three layers: the innermost layer was a 27-channel (23) Na receive helmet which was surrounded by a four-channel (23) Na transceiver array. The outer layer consisted of a four-channel (1) H dipole array for B0 shimming and anatomical localization. Transmit and receive performance of the (23) Na arrays was compared to a single-tuned (23) Na birdcage resonator. While the transmit efficiency of the (23) Na transceiver array was comparable to the birdcage, the (23) Na receive array provided substantial signal-to-noise ratio (SNR) gain near the surface and comparable SNR in the center. The utility of this customized setup was demonstrated by (23) Na images of excellent quality. High SNR, efficient transmit excitation and B0 shimming capability can be achieved for (23) Na MRI at 9.4T using novel coil combination. This RF configuration is easily adaptable to other multinuclei applications at ultra high field (≥ 7T). © 2015 Wiley Periodicals, Inc.

  15. Comparisons of benthic filter feeder communities before and after a large-scale capital dredging program.

    Science.gov (United States)

    Abdul Wahab, Muhammad Azmi; Fromont, Jane; Gomez, Oliver; Fisher, Rebecca; Jones, Ross

    2017-09-15

    Changes in turbidity, sedimentation and light over a two year large scale capital dredging program at Onslow, northwestern Australia, were quantified to assess their effects on filter feeder communities, in particular sponges. Community functional morphological composition was quantified using towed video surveys, while dive surveys allowed for assessments of species composition and chlorophyll content. Onslow is relatively diverse recording 150 sponge species. The area was naturally turbid (1.1 mean P 80 NTU), with inshore sites recording 6.5× higher turbidity than offshore localities, likely influenced by the Ashburton River discharge. Turbidity and sedimentation increased by up to 146% and 240% through dredging respectively, with corresponding decreases in light levels. The effects of dredging was variable, and despite existing caveats (i.e. bleaching event and passing of a cyclone), the persistence of sponges and the absence of a pronounced response post-dredging suggest environmental filtering or passive adaptation acquired pre-dredging may have benefited these communities. Copyright © 2017. Published by Elsevier Ltd.

  16. Real-time modeling and simulation of distribution feeder and distributed resources

    Science.gov (United States)

    Singh, Pawan

    The analysis of the electrical system dates back to the days when analog network analyzers were used. With the advent of digital computers, many programs were written for power-flow and short circuit analysis for the improvement of the electrical system. Real-time computer simulations can answer many what-if scenarios in the existing or the proposed power system. In this thesis, the standard IEEE 13-Node distribution feeder is developed and validated on a real-time platform OPAL-RT. The concept and the challenges of the real-time simulation are studied and addressed. Distributed energy resources include some of the commonly used distributed generation and storage devices like diesel engine, solar photovoltaic array, and battery storage system are modeled and simulated on a real-time platform. A microgrid encompasses a portion of an electric power distribution which is located downstream of the distribution substation. Normally, the microgrid operates in paralleled mode with the grid; however, scheduled or forced isolation can take place. In such conditions, the microgrid must have the ability to operate stably and autonomously. The microgrid can operate in grid connected and islanded mode, both the operating modes are studied in the last chapter. Towards the end, a simple microgrid controller modeled and simulated on the real-time platform is developed for energy management and protection for the microgrid.

  17. Feasibility assessment of optical technologies for reliable high capacity feeder links

    Science.gov (United States)

    Witternigg, Norbert; Schönhuber, Michael; Leitgeb, Erich; Plank, Thomas

    2013-08-01

    Space telecom scenarios like data relay satellite and broadband/broadcast service providers require reliable feeder links with high bandwidth/data rate for the communication between ground station and satellite. Free space optical communication (FSOC) is an attractive alternative to microwave links, improving performance by offering abundant bandwidth at small apertures of the optical terminals. At the same time Near-Earth communication by FSOC avoids interference with other services and is free of regulatory issues. The drawback however is the impairment by the laser propagation through the atmosphere at optical wavelengths. Also to be considered are questions of eye safety for ground personnel and aviation. In this paper we assess the user requirements for typical space telecom scenarios and compare these requirements with solutions using optical data links through the atmosphere. We suggest a site diversity scheme with a number of ground stations and a switching scheme using two optical terminals on-board the satellite. Considering the technology trade-offs between four different optical wavelengths we recommend the future use of 1.5 μm laser technology and calculate a link budget for an atmospheric condition of light haze on the optical path. By comparing link budgets we show an outlook to the future potential use of 10 μm laser technology.

  18. Controlling Voltage Levels of Distribution Network-Radial Feeder after Connecting Wind Turbines to the Network

    Directory of Open Access Journals (Sweden)

    Muhammad Al Badri

    2017-11-01

    Full Text Available Several factors in power generation and supply need to be taken into account such as shortages of energy supply, system stability, and energy quality and system disruption due to network losses, industrial development and population expansion. The addition of wind turbines to the distribution network is of great benefit in providing additional power and solving these problems, but this addition is accompanied by the problem of low voltage network. This research found optimal solutions to the problem of low voltage distribution network after connecting wind turbines. The main idea of this paper is to optimize the low-voltage problem as a result of connecting the wind turbines to the "far end" of the radial feeder for a distribution network and to obtain a voltage level within an acceptable and stable range. The problem of low voltage solved by using the load-drop compensation, capacitor-bank and “doubly-fed” induction generators. The results of this study were based on the operation of the entire design of the simulation system which would be compatible with the reality of the energy flow of all network components by using the PSCAD program. The present analysis program revealed an optimum solution for the low voltage profile of the distribution network after connecting the wind turbine.

  19. Utilisation of symmetrical components in a communication-based protection for loop MV feeders with variable short-circuit power

    DEFF Research Database (Denmark)

    Ciontea, Catalin-Iosif; Bak, Claus Leth; Blaabjerg, Frede

    2018-01-01

    -circuit power is presented. It relies on utilisation of symmetrical components of the short-circuit currents and on communication between the protection relays. The proposed method addresses the Single Phase to Ground (SPG) faults occurring in directly grounded distribution networks, with focus on closed......Variability of the available short-circuit power also implies variation of the fault level, which can potentially cause several protection problems in the electric networks. In this paper, a novel protection method that is insensitive to the fault level changes caused by variable short......-loop Medium Voltage (MV) feeders. Case studies are presented, which demonstrate that the proposed protection scheme is capable of effectively detecting the SPG faults in closed-loop feeders with variable short-circuit power....

  20. A Double-Resistive Active Power Filter System to Attenuate Harmonic Voltages of a Radial Power Distribution Feeder

    DEFF Research Database (Denmark)

    Sun, Xiaofeng; Han, Ruijing; Shen, Hong

    2016-01-01

    voltages. This paper proposes a double-resistive active power filter (D-RAPF) system consisting of a terminal-RAPF and an attenuation-RAPF for each individual harmonic. The terminal-RAPF operating as the characteristic impedance of the feeder is installed at the end bus to suppress harmonic propagation......Harmonic propagation between power-factor correction capacitors and system inductors seriously deteriorates power quality in a radial power distribution feeder. Installation of a resistive active power filter (RAPF) at the end bus only suppresses harmonic propagation, not attenuates harmonic...... at all harmonic frequencies. The attenuation-RAPF, whose control gain can be set according to the requirements of the harmonic voltage distortion limit, is installed at a specific position for each individual harmonic to attenuate the corresponding harmonic voltages. The D-RAPF system not only suppresses...

  1. Power Hardware-in-the-Loop Evaluation of PV Inverter Grid Support on Hawaiian Electric Feeders: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Austin; Prabakar, Kumaraguru; Nagarajan, Adarsh; Nepal, Shaili; Hoke, Anderson; Asano, Marc; Ueda, Reid; Ifuku, Earle

    2017-05-08

    As more grid-connected photovoltaic (PV) inverters become compliant with evolving interconnections requirements, there is increased interest from utilities in understanding how to best deploy advanced grid-support functions (GSF) in the field. One efficient and cost-effective method to examine such deployment options is to leverage power hardware-in-the-loop (PHIL) testing methods. Two Hawaiian Electric feeder models were converted to real-time models in the OPAL-RT real-time digital testing platform, and integrated with models of GSF capable PV inverters that were modeled from characterization test data. The integrated model was subsequently used in PHIL testing to evaluate the effects of different fixed power factor and volt-watt control settings on voltage regulation of the selected feeders. The results of this study were provided as inputs for field deployment and technical interconnection requirements for grid-connected PV inverters on the Hawaiian Islands.

  2. Metaplasia of the parietal layer of Bowman's capsule in the human kidney. Incidence in alcoholic liver disease and hypertension

    OpenAIRE

    Haensly, William E.

    1988-01-01

    This report is the second of two surveys to determine the incidence of metaplasia of Bowman's parietal epithelium in the human kidney. Human kidney sections obtained at autopsy at the Department of Pathology, University of Texas Medical Branch, Galveston, Texas, were examined with the light microscope. The kidneys were fixed in neutral formalin, sectioned at 6 pm and stained with hematoxylin and eosin. Autopsy records were consulted after kidney section exa...

  3. Fibronectin-calcium phosphate composite layer on hydroxyapatite to enhance adhesion, cell spread and osteogenic differentiation of human mesenchymal stem cells in vitro

    International Nuclear Information System (INIS)

    Sogo, Yu; Ito, Atsuo; Matsuno, Tomonori; Oyane, Ayako; Tamazawa, Gaku; Satoh, Tazuko; Yamazaki, Atsushi; Uchimura, Eiji; Ohno, Tadao

    2007-01-01

    Fibronectin (Fn) and type I collagen (Col) were immobilized on a surface of a hydroxyapatite (HAP) ceramic by coprecipitation with calcium phosphate in a supersaturated calcium phosphate solution prepared by mixing clinically approved infusion fluids. These proteins and the calcium phosphate precipitate formed a composite surface layer. As a result, the proteins were immobilized firmly as not to be released completely for 3 d in a physiological salt solution. When human mesenchymal stem cells (hMSCs) were cultured on a HAP ceramic in a differentiation medium supplemented with dexamethasone, β-glycerophosphate and ascorbic acid, hMSCs spread well within 1 h. The alkaline phosphatase (ALP) activity of hMSCs cultured on the Fn-calcium phosphate composite layer significantly increased compared with that of hMSCs cultured on the untreated HAP ceramic. On the other hand, Col did not increase the ALP activity of hMSCs and no synergy between Fn and Col was observed. Therefore, the Fn-calcium phosphate composite layer formed on the HAP is useful for the enhancement of the spreading and osteogenic differentiation of hMSCs in vitro

  4. Effects of Home Energy Management Systems on Distribution Utilities and Feeders Under Various Market Structure; NREL (National Renewable Energy Laboratory)

    Energy Technology Data Exchange (ETDEWEB)

    Ruth, M.; Pratt, A.; Lunacek, M.; Mittal, S.; Wu, H.; Jones, W.

    2015-06-15

    The combination of distributed energy resources (DER) and retail tariff structures to provide benefits to both utility consumers and the utilities is not well understood. To improve understanding, an Integrated Energy System Model (IESM) is being developed to simulate the physical and economic aspects of DER technologies, the buildings where they reside, and feeders servicing them. The IESM was used to simulate 20 houses with home energy management systems on a single feeder under a time-of-use (TOU) tariff to estimate economic and physical impacts on both the households and the distribution utilities. Home energy management systems (HEMS) reduce consumers’ electric bills by precooling houses in the hours before peak electricity pricing. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices, resulting in a higher peak load. used to simulate 20 houses with home energy management systems on a single feeder under a time-of-use (TOU) tariff to estimate economic and physical impacts on both the households and the distribution utilities. Home energy management systems (HEMS) reduce consumers’ electric bills by precooling houses in the hours before peak electricity pricing. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices, resulting in a higher peak load.

  5. Differences in carotenoid accumulation among three feeder-cricket species: implications for carotenoid delivery to captive insectivores.

    Science.gov (United States)

    Ogilvy, Victoria; Fidgett, Andrea L; Preziosi, Richard F

    2012-01-01

    There are a limited number of feeder-invertebrates available to feed captive insectivores, and many are deficient in certain nutrients. Gut-loading is used to increase the diversity of nutrients present in the captive insectivore diet; however, little is known about delivery of carotenoids via gut-loading. Carotenoids may influence health and reproduction due to their roles in immune and antioxidant systems. We assessed interspecific variation in carotenoid accumulation and retention in three feeder-cricket species (Gryllus bimaculatus, Gryllodes sigillatus and Acheta domesticus) fed one of three diets (wheat-bran, fish-food based formulated diet, and fresh fruit and vegetables). Out of the three species of feeder-cricket in the fish-food-based dietary treatment group, G. bimaculatus had the greatest total carotenoid concentration. All cricket species fed the wheat-bran diet had very low carotenoid concentrations. Species on the fish-food-based diet had intermediate carotenoid concentrations, and those on the fruit and vegetable diet had the highest concentrations. Carotenoid retention was poor across all species. Overall, this study shows that, by providing captive insectivores with G. bimaculatus crickets recently fed a carotenoid-rich diet, the quantity of carotenoids in the diet can be increased. © 2011 Wiley Periodicals, Inc.

  6. Optimal distribution feeder reconfiguration for increasing the penetration of plug-in electric vehicles and minimizing network costs

    International Nuclear Information System (INIS)

    Kavousi-Fard, Abdollah; Abbasi, Alireza; Rostami, Mohammad-Amin; Khosravi, Abbas

    2015-01-01

    Appearance of PEVs (Plug-in Electric Vehicles) in future transportation sector brings forward opportunities and challenges from grid perspective. Increased utilization of PEVs will result in problems such as greater total loss, unbalanced load factor, feeder congestion and voltage drop. PEVs are mobile energy storages dispersed all over the network with benefits to both owners and utilities in case of V2G (Vehicle-to-Grid) possibility. The intelligent bidirectional power flow between grid and large number of vehicles adds complexity to the system and requires operative tools to schedule V2G energy and subdue PEV impacts. In this paper, DFR (Distribution Feeder Reconfiguration) is utilized to optimally coordinate PEV operation in a stochastic framework. Uncertainty in PEVs characteristics can be due to several sources from location and time of grid connection to driving pattern and battery SoC (State-of-Charge). The proposed stochastic problem is solved with a self-adaptive evolutionary swarm algorithm based on SSO (Social Spider Optimization) algorithm. Numerical studies verify the efficacy of the proposed DFR to improve the system performance and optimal dispatch of V2G. - Highlights: • Consideration effect of PEVS on the distribution feeder reconfiguration. • Increasing the penetration of PEVS. • Introducing a new artificial optimization algorithm. • Modeling the uncertainty in network. • Investigating the degradation cost of batteries in V2G technology.

  7. Cool Down Experiences with the SST-1 Helium Cryogenics System before and after Current Feeders System Modification

    Science.gov (United States)

    Patel, R.; Panchal, P.; Panchal, R.; Tank, J.; Mahesuriya, G.; Sonara, D.; Srikanth, G. L. N.; Garg, A.; Bairagi, N.; Christian, D.; Patel, K.; Shah, P.; Nimavat, H.; Sharma, R.; Patel, J. C.; Gupta, N. C.; Prasad, U.; Sharma, A. N.; Tanna, V. L.; Pradhan, S.

    The SST-1 machine comprises a superconducting magnet system (SCMS), which includes TF and PF magnets. In order to charge the SCMS, we need superconducting current feeders consisting of SC feeders and vapor cooled current leads (VCCLs). We have installed all 10 (+/-) pairs of VCCLs for the TF and PF systems. While conducting initial engineering validation of the SST-1 machine, our prime objective was to produce circular plasma using only the TF system. During the SST-1 campaign I to VI, we have to stop the PF magnets cooling in order to get the cryo- stable conditions for current charging of the TF magnets system. In that case, the cooling of the PF current leads is not essential. It has been also observed that after aborting the PF system cooling, there was a limited experimental window of TF operation. Therefore, in the recent SST-1 campaign-VII, we removed the PF current leads (9 pairs) and kept only single (+/-) pair of the 10,000 A rated VCCLs to realize the charging of the TF system for the extended window of operation. We have observed a better cryogenic stability in the TF magnets after modifications in the CFS. In this paper, we report the comparison of the cool down performance for the SST-1 machine operation before and after modifications of the current feeders system.

  8. Busbar arcs at large fusion magnets: Conductor to feeder tube arcing model experiments with the LONGARC device

    Energy Technology Data Exchange (ETDEWEB)

    Klimenko, Dmitry, E-mail: dmitry.klimenko@kit.edu; Pasler, Volker

    2014-10-15

    Highlights: •The LONGARC device was successfully implemented for busbar to feeder tubes arcing model experiments. •Arcing at an ITER busbar inside its feeder tube was simulated in scaled model experiments. •The narrower half tubes imply a slight increase of the arc propagation speed in compare to full tube experiments. •All simulated half tubes experiments show severe damage indicating that the ITER inner feeder tube will not withstand a busbar arc. -- Abstract: Electric arcs moving along the power cables (the so-called busbars) of the toroidal field (TF) coils of ITER may reach and penetrate the cryostat wall. Model experiments with the new LONGARC device continue the VACARC (VACuum ARC) experiments that were initiated to investigate the propagation and destruction mechanisms of busbar arcs in small scale [1]. The experiments are intended to support the development and validation of a numerical model. LONGARC overcomes the space limitations inside VACARC and allows also for advanced 1:3 (vs. ITER full scale) model setups. The LONGARC device and first results are presented below.

  9. Two-layer membranes of calcium phosphate/collagen/PLGA nanofibres: in vitro biomineralisation and osteogenic differentiation of human mesenchymal stem cells

    Science.gov (United States)

    Hild, Nora; Schneider, Oliver D.; Mohn, Dirk; Luechinger, Norman A.; Koehler, Fabian M.; Hofmann, Sandra; Vetsch, Jolanda R.; Thimm, Benjamin W.; Müller, Ralph; Stark, Wendelin J.

    2011-02-01

    The present study evaluates the in vitro biomedical performance of an electrospun, flexible, anisotropic bilayer with one layer containing a collagen to mineral ratio similar to that in bone. The double membrane consists of a poly(lactide-co-glycolide) (PLGA) layer and an amorphous calcium phosphate (a-CaP)/collagen (Col)/PLGA layer. In vitro biomineralisation and a cell culture study with human mesenchymal stem cells (hMSC) were conducted to characterise such membranes for possible application as biomaterials. Nanofibres with different a-CaP/Col/PLGA compositions were synthesised by electrospinning to mimic the actual composition of bone tissue. Immersion in simulated body fluid and in cell culture medium resulted in the deposition of a hydroxyapatite layer. Incubation of hMSC for 4 weeks allowed for assessment of the proliferation and osteogenic differentiation of the cells on both sides of the double membrane. Confocal laser scanning microscopy was used to observe the proper adhesion of the cells. Calcium and collagen content was proven by Alizarin red S and Sirius red assays. Acute cytotoxic effects of the nanoparticles or the chemicals used in the scaffold preparation could be excluded based on viability assays (alamarBlue and alkaline phosphatase activity). The findings suggest possible application of such double membranes is in treatment of bone defects with complex geometries as wound dressing material.The present study evaluates the in vitro biomedical performance of an electrospun, flexible, anisotropic bilayer with one layer containing a collagen to mineral ratio similar to that in bone. The double membrane consists of a poly(lactide-co-glycolide) (PLGA) layer and an amorphous calcium phosphate (a-CaP)/collagen (Col)/PLGA layer. In vitro biomineralisation and a cell culture study with human mesenchymal stem cells (hMSC) were conducted to characterise such membranes for possible application as biomaterials. Nanofibres with different a

  10. Water quality in Pearl Harbor and feeder streams during 1971 - 2001 collected primarily by oceanography students from Leeward Community College (NODC Accession 0000590)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Water quality data were collected in Pearl Harbor and surrounding feeder streams from 30 December 1971 to 24 August 2001. Data were collected by Leeward Community...

  11. Rat embryonic fibroblasts improve reprogramming of human keratinocytes into induced pluripotent stem cells.

    Science.gov (United States)

    Linta, Leonhard; Stockmann, Marianne; Kleinhans, Karin N; Böckers, Anja; Storch, Alexander; Zaehres, Holm; Lin, Qiong; Barbi, Gotthold; Böckers, Tobias M; Kleger, Alexander; Liebau, Stefan

    2012-04-10

    Patient-specific human induced pluripotent stem (hiPS) cells not only provide a promising tool for cellular disease models in general, but also open up the opportunity to establish cell-type-specific systems for personalized medicine. One of the crucial prerequisites for these strategies, however, is a fast and efficient reprogramming strategy from easy accessible somatic cell populations. Keratinocytes from plucked human hair had been introduced as a superior cell source for reprogramming purposes compared with the widely used skin fibroblasts. The starting cell population is, however, limited and thereby further optimization in terms of time, efficiency, and quality is inevitable. Here we show that rat embryonic fibroblasts (REFs) should replace mouse embryonic fibroblasts as feeder cells in the reprogramming process. REFs enable a significantly more efficient reprogramming procedure as shown by colony number and total amount of SSEA4-positive cells. We successfully produced keratinocyte-derived hiPS (k-hiPS) cells from various donors. The arising k-hiPS cells display the hallmarks of pluripotency such as expression of stem cell markers and differentiation into all 3 germ layers. The increased reprogramming efficiency using REFs as a feeder layer occurred independent of the proliferation rate in the parental keratinocytes and acts, at least in part, in a non-cell autonomous way by secreting factors known to facilitate pluripotency such as Tgfb1, Inhba and Grem1. Hence, we provide an easy to use and highly efficient reprogramming system that could be very useful for a broad application to generate human iPS cells. © Mary Ann Liebert, Inc.

  12. Variations in Humanized and Defined Culture Conditions Supporting Derivation of New Human Embryonic Stem Cell Lines

    DEFF Research Database (Denmark)

    Fletcher, Judy M; Ferrier, Patricia M; Gardner, John O

    2006-01-01

    matrix substrate of purified human laminin (Ln) with transitional reliance on mitotically inactivated human fibroblast (HDF) feeder cells. With this integrated system hESC lines were isolated using either HDF conditioned medium supplemented with a bovine-sourced serum replacement (bSRM), or a defined...

  13. Changes in food intake and abnormal behavior using a puzzle feeder in newly acquired sub-adult rhesus monkeys (Macaca mulatta): a short term study.

    Science.gov (United States)

    Lee, Jae-Il; Lee, Chi-Woo; Kwon, Hyouk-Sang; Kim, Young-Tae; Park, Chung-Gyu; Kim, Sang-Joon; Kang, Byeong-Cheol

    2008-10-01

    The majority of newly acquired nonhuman primates encounter serious problems adapting themselves to new environments or facilities. In particular, loss of appetite and abnormal behavior can occur in response to environmental stresses. These adaptation abnormalities can ultimately have an affect on the animal's growth and well-being. In this study, we evaluated the affects of a puzzle feeder on the food intake and abnormal behavior of newly acquired rhesus monkeys for a short period. The puzzle feeder was applied to 47- to 58-month-old animals that had never previously encountered one. We found that there was no difference in the change of food intake between the bucket condition and the puzzle feeder condition. In contrast, the time spent for consumption of food was three times longer in the puzzle feeder condition than in the bucket condition. Two monkeys initially exhibited stereotypic behavior. One showed a decreasing, and the other an increasing pattern of abnormal behavior after introduction of the puzzle feeder. In conclusion, this result suggests that over a short period, the puzzle feeder can only affect the time for food consumption since it failed to affect the food intake and did not consistently influence stereotypic behaviors in newly acquired rhesus monkeys.

  14. Adjusting the weaning age of calves fed by automated feeders according to individual intakes of solid feed.

    Science.gov (United States)

    de Passillé, A M; Rushen, J

    2012-09-01

    When weaned at the ages typical of commercial dairy production, dairy calves usually show reduced growth rates, lowered energy intake, and increased behavioral signs of hunger, reflecting their difficulty in switching from a milk diet to solid feed. However, large differences exist between calves in their ability to adapt to solid feed, and automated feeders allow the age of weaning to be adjusted to an individual calf's intake of solid feed. We examined the effects of weaning according to solid feed intake on age at weaning, feed intake, and behavioral signs of hunger. In a 2×2 factorial design, 60 female Holstein calves in groups of 8 and fed milk, grain starter, and hay from automated feeders began to be weaned when their voluntary intake of grain starter was either 400 g/d (high start) or 200 g/d (low start), with weaning completed when their voluntary intakes of starter were either 1,600 g/d (high end) or 800 g/d (low end). Digestible energy intakes were calculated from milk, starter and hay intakes, corrected for body weights, calves were weighed, and the frequency of visits to the milk feeders were measured each day. The main effects and interactions between treatments were tested with ANOVA. Large differences were observed between calves in the age at which weaning was complete, with weaning completed earlier for low-end calves compared with high-end calves. No treatment effects (either of start amount or end amount) on intakes of milk, starter, or hay or on weight gains occurred. However, the calves that began weaning earlier had longer durations of weaning, greater growth rates from d 20 to 87, and were heavier on d 87, and had lower milk intakes, higher starter intakes, higher hay intakes, and a greater digestible energy intake, but showed more unrewarded visits to the milk feeder. Adjusting the age at which individual calves are weaned off milk according to their ability to eat solid feed can reduce the age at which weaning occurs while reducing the

  15. The filter feeder Dreissena polymorpha affects nutrient, silicon, and metal(loid) mobilization from freshwater sediments.

    Science.gov (United States)

    Schaller, Jörg; Planer-Friedrich, Britta

    2017-05-01

    Organic sediments in aquatic ecosystems are well known sinks for nutrients, silicon, and metal(loid)s. Organic matter-consuming organisms like invertebrate shredders, grazers, and bioturbators significantly affect element fixation or remobilization by changing redox conditions or binding properties of organic sediments. Little is known about the effect of filter feeders, like the zebra mussel Dreissena polymorpha, an invasive organism in North American and European freshwater ecosystems. A laboratory batch experiment exposing D. polymorpha (∼1200 organisms per m 2 ) to organic sediment from a site contaminated with arsenic, copper, lead, and uranium revealed a significant uptake and accumulation of arsenic, copper, iron, and especially uranium both into the soft body tissues and the seashell. This is in line with previous observations of metal(loid) accumulation from biomonitoring studies. Regarding its environmental impact, D. polymorpha significantly contributed to mobilization of silicon, iron, phosphorus, arsenic, and copper and to immobilization of uranium (p < 0.001), probably driven by redox conditions, microbial activity within the gut system, or active control of element homeostasis. No net mobilization or immobilization was observed for zinc and lead, because of their low mobility at the prevailing pH of 7.5-8.5. The present results suggest that D. polymorpha can both ameliorate (nutrient mobilization, immobilization of toxicants mobile under oxic conditions) or aggravate negative effects (mobilization of toxicants mobile under reducing conditions) in ecosystems. Relating the results of the present study to observed population densities in natural freshwater ecosystems suggests a significant influence of D. polymorpha on element cycling and needs to be considered in future studies. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Uptake, accumulation, and biotransformation of metal oxide nanoparticles by a marine suspension-feeder

    International Nuclear Information System (INIS)

    Montes, Milka O.; Hanna, Shannon K.; Lenihan, Hunter S.; Keller, Arturo A.

    2012-01-01

    Highlights: ► Suspension-feeding by mussels can greatly alter mobility and fate of metal oxide nanoparticles. ► Bioprocessing of metal oxide nanoparticles by mussels removes large fraction from water column. ► Mussels repackage metal oxide nanoparticles in highly concentrated pseudofeces. ► Novel biological pathway between major compartments in marine systems. ► Very different outcome for ZnO and CeO 2 nanoparticles based on their solubility. - Abstract: A growing body of evidence indicates that some engineered nanoparticles (ENPs) are toxic to organisms that perform important ecosystem services in terrestrial and aquatic ecosystems. However, toxicity can be influenced by the biotransformation of contaminants, including ENPs, as it may alter the fate and transport of these substances. In turn, fate and transport can influence their bioavailability. To understand how biotransformation influences the fate and transport of ENPs in marine ecosystems, we exposed suspension-feeding mussels, Mytilus galloprovincialis, to two common nano-metal oxides, CeO 2 and ZnO, over a range of concentrations from 1 mg L −1 to 10 mg L −1 , in a laboratory experiment. Mussels exposed to 10 mg L −1 accumulated 62 μg g −1 of Ce and 880 μg g −1 of Zn on a dry tissue basis but rejected 21,000 μg g −1 for Ce and 63,000 μg g −1 for Zn in pseudofeces. Scanning electron microscope evidence indicates CeO 2 remained as ENPs but ZnO did not after being rejected by the mussels. Mussels filtered most of the CeO 2 from the aqueous media, while a significant fraction of Zn remained in solution. Differences in ENP solubility affect ENP uptake, excretion, and accumulation in mussels. Our study highlights the potential role of marine suspension feeders in biotransformation of ENPs.

  17. A new stalked filter-feeder from the middle Cambrian Burgess Shale, British Columbia, Canada.

    Directory of Open Access Journals (Sweden)

    Lorna J O'Brien

    Full Text Available Burgess Shale-type deposits provide invaluable insights into the early evolution of body plans and the ecological structure of Cambrian communities, but a number of species, continue to defy phylogenetic interpretations. Here we extend this list to include a new soft-bodied animal, Siphusauctum gregarium n. gen. and n. sp., from the Tulip Beds (Campsite Cliff Shale Member, Burgess Shale Formation of Mount Stephen (Yoho National Park, British Columbia. With 1,133 specimens collected, S. gregarium is clearly the most abundant animal from this locality.This stalked animal (reaching at least 20 cm in length, has a large ovoid calyx connected to a narrow bilayered stem and a small flattened or bulb-like holdfast. The calyx is enclosed by a flexible sheath with six small openings at the base, and a central terminal anus near the top encircled by indistinct openings. A prominent organ, represented by six radially symmetrical segments with comb-like elements, surrounds an internal body cavity with a large stomach, conical median gut and straight intestine. Siphusauctum gregarium was probably an active filter-feeder, with water passing through the calyx openings, capturing food particles with its comb-like elements. It often occurs in large assemblages on single bedding planes suggesting a gregarious lifestyle, with the animal living in high tier clusters. These were probably buried en masse more or less in-situ by rapid mud flow events.Siphusauctum gregarium resembles Dinomischus, another Cambrian enigmatic stalked animal. Principal points of comparison include a long stem with a calyx containing a visceral mass and bract-like elements, and a similar lifestyle albeit occupying different tiering levels. The presence in both animals of a digestive tract with a potential stomach and anus suggest a grade of organization within bilaterians, but relationships with extant phyla are not straightforward. Thus, the broader affinities of S. gregarium remain

  18. Interstitial cells of Cajal in human small intestine. Ultrastructural identification and organization between the main smooth muscle layers

    DEFF Research Database (Denmark)

    Rumessen, J J; Thuneberg, L

    1991-01-01

    with elastin fibers. The organization shown in this study strongly supports the concept of interstitial cells of Cajal as important regulatory cells also in the human small intestine. The characteristic cytology and organization of interstitial cells of Cajal may provide a basis for future morphological......Previous morphological and electrophysiological studies have supported the hypothesis that interstitial cells of Cajal have important regulatory (pacemaker) functions in the gut. In the current study, interstitial cells of Cajal associated with Auerbach's plexus in human small intestine were...... studied. Freshly resected intestine was examined by light and electron microscopy. The interstitial cells of Cajal resembled modified smooth muscle cells. They had caveolae and dense bodies, an incomplete basal lamina, a very well-developed smooth endoplasmic reticulum, and abundant intermediate (10 nm...

  19. Generation of human-induced pluripotent stem cells from burn patient-derived skin fibroblasts using a non-integrative method.

    Science.gov (United States)

    Fu, Shangfeng; Ding, Jianwu; Liu, Dewu; Huang, Heping; Li, Min; Liu, Yang; Tu, Longxiang; Liu, Deming

    2018-01-01

    Patient specific induced pluripotent stem cells (iPSCs) have been recognized as a possible source of cells for skin tissue engineering. They have the potential to greatly benefit patients with large areas of burned skin or skin defects. However, the integration virus-based reprogramming method is associated with a high risk of genetic mutation and mouse embryonic fibroblast feeder-cells may be a pollutant. In the present study, human skin fibroblasts (HSFs) were successfully harvested from patients with burns and patient-specific iPSCs were generated using a non-integration method with a feeder-free approach. The octamer-binding transcription factor 4 (OCT4), sex-determining region Y box 2 (SOX2) and NANOG transcription factors were delivered using Sendai virus vectors. iPSCs exhibited representative human embryonic stem cell-like morphology and proliferation characteristics. They also expressed pluripotent markers, including OCT4, NANOG, SOX2, TRA181, stage-specific embryonic antigen 4 and TRA-160, and exhibited a normal karyotype. Teratoma and embryoid body formation revealed that iPSCs were able to differentiate into cells of all three germ layers in vitro and in vivo. The results of the present study demonstrate that HSFs derived from patients with burns, may be reprogrammed into stem cells with pluripotency, which provides a basis for cell‑based skin tissue engineering in the future.

  20. Stepwise Differentiation of Pluripotent Stem Cells into Osteoblasts Using Four Small Molecules under Serum-free and Feeder-free Conditions

    Directory of Open Access Journals (Sweden)

    Kosuke Kanke

    2014-06-01

    Full Text Available Pluripotent stem cells are a promising tool for mechanistic studies of tissue development, drug screening, and cell-based therapies. Here, we report an effective and mass-producing strategy for the stepwise differentiation of mouse embryonic stem cells (mESCs and mouse and human induced pluripotent stem cells (miPSCs and hiPSCs, respectively into osteoblasts using four small molecules (CHIR99021 [CHIR], cyclopamine [Cyc], smoothened agonist [SAG], and a helioxanthin-derivative 4-(4-methoxyphenylpyrido[4′,3′:4,5]thieno[2,3-b]pyridine-2-carboxamide [TH] under serum-free and feeder-free conditions. The strategy, which consists of mesoderm induction, osteoblast induction, and osteoblast maturation phases, significantly induced expressions of osteoblast-related genes and proteins in mESCs, miPSCs, and hiPSCs. In addition, when mESCs defective in runt-related transcription factor 2 (Runx2, a master regulator of osteogenesis, were cultured by the strategy, they molecularly recapitulated osteoblast phenotypes of Runx2 null mice. The present strategy will be a platform for biological and pathological studies of osteoblast development, screening of bone-augmentation drugs, and skeletal regeneration.

  1. Isolation and characterization of true mesenchymal stem cells derived from human term decidua capable of multilineage differentiation into all 3 embryonic layers.

    Science.gov (United States)

    Macias, Maria I; Grande, Jesús; Moreno, Ana; Domínguez, Irene; Bornstein, Rafael; Flores, Ana I

    2010-11-01

    The objective of the study was to isolate and characterize a population of mesenchymal stem cells (MSCs) from human term placental membranes. We isolated an adherent cell population from extraembryonic membranes. Morphology, phenotype, growth characteristics, karyotype, and immunological and differentiation properties were analyzed. The isolated placental MSCs were from maternal origin and named as decidua-derived mesenchymal stem cells (DMSCs). DMSCs differentiated into derivatives of all germ layers. It is the first report about placental MSC differentiation into alveolar type II cells. Clonally expanded DMSCs differentiated into all embryonic layers, including pulmonary cells. DMSCs showed higher life span than placental cells from fetal origin and proliferated without genomic instability. The data suggest that DMSCs are true multipotent MSCs, distinguishing them from other placental MSCs. DMSCs could be safely used in the mother as a potential source of MSCs for pelvic floor dysfunctions and immunological diseases. Additionally, frozen DMSCs can be stored for both autologous and allogeneic tissue regeneration. Copyright © 2010 Mosby, Inc. All rights reserved.

  2. Simulation of laser propagation through a three-layer human skin model in the spectral range from 1000 to 1900 nm

    Science.gov (United States)

    Nasouri, Babak; Murphy, Thomas E.; Berberoglu, Halil

    2014-07-01

    For understanding the mechanisms of low-level laser/light therapy (LLLT), accurate knowledge of light interaction with tissue is necessary. We present a three-dimensional, multilayer reduced-variance Monte Carlo simulation tool for studying light penetration and absorption in human skin. Local profiles of light penetration and volumetric absorption were calculated for uniform as well as Gaussian profile beams with different spreads over the spectral range from 1000 to 1900 nm. The results showed that lasers within this wavelength range could be used to effectively and safely deliver energy to specific skin layers as well as achieve large penetration depths for treating deep tissues, without causing skin damage. In addition, by changing the beam profile from uniform to Gaussian, the local volumetric dosage could increase as much as three times for otherwise similar lasers. We expect that this tool along with the results presented will aid researchers in selecting wavelength and laser power in LLLT.

  3. Effect of concentrate feeder design on performance, eating and animal behavior, welfare, ruminal health, and carcass quality in Holstein bulls fed high-concentrate diets.

    Science.gov (United States)

    Verdú, M; Bach, A; Devant, M

    2015-06-01

    A total of 240 Holstein bulls (121 ± 2.0 kg initial BW; 99 ± 1.0 d of age), from 2 consecutive fattening cycles, were randomly allocated in 1 of 6 pens and assigned to 1 of the 3 treatments consisting of different concentrate feeder designs: a control feeder with 4 feeding spaces (CF), a feeder with less concentrate capacity (CFL), and a single-space feeder with lateral protections (SF). Each pen had a straw feeder and a drinker. All animals were fed a high-concentrate diet for ad libitum intake. Concentrate consumption was recorded daily using a computerized feeder, straw consumption was recorded weekly, and BW was recorded every 14 d. Animal behavior was registered on d 1, 3, 5, 8, and 14 and every 28 d by scan sampling. Eating behavior at concentrate feeders was filmed on d 12, 125, and 206. On d 7, 120, and 204, samples of rumen contents were collected for measurement of pH and VFA and blood samples were obtained to analyze NEFA, haptoglobin, glucose, and insulin. Animals were slaughtered after 223 d, and HCW and lesions of the rumen wall and liver were recorded. The accumulative concentrate consumption per animal tended (P = 0.09) to be greater with CF than with CFL and SF. Also, CV of concentrate consumption was greater (P carcass data. Also, no differences among treatments in rumen wall evaluation and liver abscesses were observed. At 7 and 204 d of study, SF bulls had greater (P animal welfare in Holstein bulls fed high-concentrate diets. However, at the beginning, there was evidence that animals fed using SF had problems with adaptation.

  4. Uptake, accumulation, and biotransformation of metal oxide nanoparticles by a marine suspension-feeder

    Energy Technology Data Exchange (ETDEWEB)

    Montes, Milka O. [University of California Center for Environmental Implications of Nanotechnology, Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States); University of Texas of the Permian Basin, 4901 E. University, Odessa, TX 79762 (United States); Hanna, Shannon K.; Lenihan, Hunter S. [University of California Center for Environmental Implications of Nanotechnology, Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States); Keller, Arturo A., E-mail: keller@bren.ucsb.edu [University of California Center for Environmental Implications of Nanotechnology, Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States)

    2012-07-30

    Highlights: Black-Right-Pointing-Pointer Suspension-feeding by mussels can greatly alter mobility and fate of metal oxide nanoparticles. Black-Right-Pointing-Pointer Bioprocessing of metal oxide nanoparticles by mussels removes large fraction from water column. Black-Right-Pointing-Pointer Mussels repackage metal oxide nanoparticles in highly concentrated pseudofeces. Black-Right-Pointing-Pointer Novel biological pathway between major compartments in marine systems. Black-Right-Pointing-Pointer Very different outcome for ZnO and CeO{sub 2} nanoparticles based on their solubility. - Abstract: A growing body of evidence indicates that some engineered nanoparticles (ENPs) are toxic to organisms that perform important ecosystem services in terrestrial and aquatic ecosystems. However, toxicity can be influenced by the biotransformation of contaminants, including ENPs, as it may alter the fate and transport of these substances. In turn, fate and transport can influence their bioavailability. To understand how biotransformation influences the fate and transport of ENPs in marine ecosystems, we exposed suspension-feeding mussels, Mytilus galloprovincialis, to two common nano-metal oxides, CeO{sub 2} and ZnO, over a range of concentrations from 1 mg L{sup -1} to 10 mg L{sup -1}, in a laboratory experiment. Mussels exposed to 10 mg L{sup -1} accumulated 62 {mu}g g{sup -1} of Ce and 880 {mu}g g{sup -1} of Zn on a dry tissue basis but rejected 21,000 {mu}g g{sup -1} for Ce and 63,000 {mu}g g{sup -1} for Zn in pseudofeces. Scanning electron microscope evidence indicates CeO{sub 2} remained as ENPs but ZnO did not after being rejected by the mussels. Mussels filtered most of the CeO{sub 2} from the aqueous media, while a significant fraction of Zn remained in solution. Differences in ENP solubility affect ENP uptake, excretion, and accumulation in mussels. Our study highlights the potential role of marine suspension feeders in biotransformation of ENPs.

  5. A new hybrid evolutionary algorithm based on new fuzzy adaptive PSO and NM algorithms for Distribution Feeder Reconfiguration

    International Nuclear Information System (INIS)

    Niknam, Taher; Azadfarsani, Ehsan; Jabbari, Masoud

    2012-01-01

    Highlights: ► Network reconfiguration is a very important way to save the electrical energy. ► This paper proposes a new algorithm to solve the DFR. ► The algorithm combines NFAPSO with NM. ► The proposed algorithm is tested on two distribution test feeders. - Abstract: Network reconfiguration for loss reduction in distribution system is a very important way to save the electrical energy. This paper proposes a new hybrid evolutionary algorithm to solve the Distribution Feeder Reconfiguration problem (DFR). The algorithm is based on combination of a New Fuzzy Adaptive Particle Swarm Optimization (NFAPSO) and Nelder–Mead simplex search method (NM) called NFAPSO–NM. In the proposed algorithm, a new fuzzy adaptive particle swarm optimization includes two parts. The first part is Fuzzy Adaptive Binary Particle Swarm Optimization (FABPSO) that determines the status of tie switches (open or close) and second part is Fuzzy Adaptive Discrete Particle Swarm Optimization (FADPSO) that determines the sectionalizing switch number. In other side, due to the results of binary PSO(BPSO) and discrete PSO(DPSO) algorithms highly depends on the values of their parameters such as the inertia weight and learning factors, a fuzzy system is employed to adaptively adjust the parameters during the search process. Moreover, the Nelder–Mead simplex search method is combined with the NFAPSO algorithm to improve its performance. Finally, the proposed algorithm is tested on two distribution test feeders. The results of simulation show that the proposed method is very powerful and guarantees to obtain the global optimization.

  6. Index-Based Assessment of Voltage Rise and Reverse Power Flow Phenomena in a Distribution Feeder Under High PV Penetration

    DEFF Research Database (Denmark)

    Hasheminamin, Maryam; Agelidis, Vassilios G.; Salehi, Vahid

    2015-01-01

    -based methodology for assessing the impact of high solar PV generation, considering the reverse power flow and voltage rise phenomena. Indices are defined that link these two phenomena and their impact on the voltage profile across the feeder. This assessment relies on detailed modeling of the network and the solar......The proliferation of photovoltaic (PV) generation in low- and medium-voltage distribution networks is expected to continue. Qualified studies can quantify adverse impacts of high PV penetration on distribution networks and assist utilities in decision making. This paper proposes an index...

  7. Overview of improvements in work practices and instrumentation for CANDU primary heat transport feeders in-service inspections

    Energy Technology Data Exchange (ETDEWEB)

    Marcotte, O., E-mail: olivier@nucleom.ca [Nucleom Inc., Quebec, Quebec (Canada); Rousseau, G., E-mail: rousseau.gilles.a@hydro.qc.ca [Hydro Quebec, Becancour, Quebec (Canada); Rochefort, E., E-mail: erochfort@zetec.com [Zetec Canada, Quebec, Quebec (Canada)

    2013-01-15

    The Canadian nuclear industry has developed many advanced non-destructive inspection techniques to be applied safely in hazardous environments in recent years. Automated systems, manual tooling and specialized software modules have been designed since early 2000s to provide complete and very efficient fitness for service inspection of primary heat transport system carbon steel feeder pipes. These techniques deal with complex geometries, difficult access and, radioactive environment. Complementary NDE techniques, namely Ultrasounds, eddy current, phased-array UT and automated scanners are used. This presentation describes the improvements in inspection practices and the advanced data analysis features. (author)

  8. Implementation of the resonant vibratory feeders control algorithm on Simatic S7-1200 from MATLAB Simulink enviroment

    Directory of Open Access Journals (Sweden)

    Mitrović Radomir B.

    2016-01-01

    Full Text Available Simulink is an important tool for modeling and simulation of process and control algorithms. It's expansion, PLC Coder, enables direct conversion of model subsystem into SCL, structured text code, which is then used by PLC IDE to create function blocks. This shortens developing time of algorithms for PLC controller. Also, this reduces possibility for a coding error. This paper describes Simulink PLC Coder and workflow for developing PID control algorithm for Siemens Simatic S7-1200 PLC. Control object used here is resonant vibratory feeder having electromagnetic drive.

  9. Introducing tool-based feeders to zoo-housed chimpanzees as a cognitive challenge: spontaneous acquisition of new types of tool use and effects on behaviours and use of space.

    OpenAIRE

    Yamanashi, Yumi; Matsunaga, Masayuki; Shimada, Kanae; Kado, Ryuichiro; Tanaka, Masayuki

    2016-01-01

    Cognitively challenging environments are vital to the welfare of captive animals. However, practical enrichment devices that can facilitate animals’ natural behaviours and accommodate individual variation are still limited. We created two types of feeders to facilitate tool-using behaviour in captive chimpanzees: pounding and dipping feeders. The pounding feeder was inspired by pestle-pounding behaviour observed in wild chimpanzees, and we expected that chimpanzees would pound soft foods. The...

  10. Ultrasensitive and Highly Stable Resistive Pressure Sensors with Biomaterial-Incorporated Interfacial Layers for Wearable Health-Monitoring and Human-Machine Interfaces.

    Science.gov (United States)

    Chang, Hochan; Kim, Sungwoong; Jin, Sumin; Lee, Seung-Woo; Yang, Gil-Tae; Lee, Ki-Young; Yi, Hyunjung

    2018-01-10

    Flexible piezoresistive sensors have huge potential for health monitoring, human-machine interfaces, prosthetic limbs, and intelligent robotics. A variety of nanomaterials and structural schemes have been proposed for realizing ultrasensitive flexible piezoresistive sensors. However, despite the success of recent efforts, high sensitivity within narrower pressure ranges and/or the challenging adhesion and stability issues still potentially limit their broad applications. Herein, we introduce a biomaterial-based scheme for the development of flexible pressure sensors that are ultrasensitive (resistance change by 5 orders) over a broad pressure range of 0.1-100 kPa, promptly responsive (20 ms), and yet highly stable. We show that employing biomaterial-incorporated conductive networks of single-walled carbon nanotubes as interfacial layers of contact-based resistive pressure sensors significantly enhances piezoresistive response via effective modulation of the interlayer resistance and provides stable interfaces for the pressure sensors. The developed flexible sensor is capable of real-time monitoring of wrist pulse waves under external medium pressure levels and providing pressure profiles applied by a thumb and a forefinger during object manipulation at a low voltage (1 V) and power consumption (<12 μW). This work provides a new insight into the material candidates and approaches for the development of wearable health-monitoring and human-machine interfaces.

  11. Development of Some Organs Derived from the Three Embryonic Germ Layer in a Degus Ectopic Pregnancy and Presence of a Cytotrophoblast That Mimics Human Chorionic Placenta

    Directory of Open Access Journals (Sweden)

    C. Bosco

    2014-01-01

    Full Text Available This report describes a case of abdominal pregnancy in an adult female degu from which we recovered two large tissular masses from the peritoneal cavity. The bigger one showed a number of thin vascular connections to the serosa layer of the small intestine. It was also directly connected to the smaller mass by a thin membranous process. The surface of the bigger mass facing the small intestine wall showed the presence of chorionic villous that resembled a villous human chorionic placenta, rather than the hemomonochorial labyrinthine placenta, characteristic of this species. This unusual finding leads us to postulate that in the degu’s uterus the cytotrophoblast is exposed to a number of factors that will activate cascades of cellular and molecular events that ultimately will be signaling the cytotrophoblast to develop into a labyrinthine hemomonochorial placenta. In absence of the proper uterine environment, as is the case of the abdominal pregnancy in the peritoneal cavity reported here, the lack of signaling will lead the cytotrophoblast to develop into a villous chorionic placenta, similar to that observed in human.

  12. An efficient hybrid evolutionary algorithm based on PSO and HBMO algorithms for multi-objective Distribution Feeder Reconfiguration

    Energy Technology Data Exchange (ETDEWEB)

    Niknam, Taher [Electronic and Electrical Engineering Department, Shiraz University of Technology, Shiraz (Iran)

    2009-08-15

    This paper introduces a robust searching hybrid evolutionary algorithm to solve the multi-objective Distribution Feeder Reconfiguration (DFR). The main objective of the DFR is to minimize the real power loss, deviation of the nodes' voltage, the number of switching operations, and balance the loads on the feeders. Because of the fact that the objectives are different and no commensurable, it is difficult to solve the problem by conventional approaches that may optimize a single objective. This paper presents a new approach based on norm3 for the DFR problem. In the proposed method, the objective functions are considered as a vector and the aim is to maximize the distance (norm2) between the objective function vector and the worst objective function vector while the constraints are met. Since the proposed DFR is a multi objective and non-differentiable optimization problem, a new hybrid evolutionary algorithm (EA) based on the combination of the Honey Bee Mating Optimization (HBMO) and the Discrete Particle Swarm Optimization (DPSO), called DPSO-HBMO, is implied to solve it. The results of the proposed reconfiguration method are compared with the solutions obtained by other approaches, the original DPSO and HBMO over different distribution test systems. (author)

  13. A look at one of the world`s largest apron feeder drives - Alberta Oil Sands Project

    Energy Technology Data Exchange (ETDEWEB)

    Persson, O. [Hagglunds Drives Canada Inc., Vancouver, BC (Canada)

    1999-10-01

    Various types of equipment to transport tar sands to processing plants are discussed, with special attention to the advantages of hydraulic direct drives over conventional electro-mechanical drives. A hydraulic direct drive such as the Hagglund Drive has exceptional starting torque capacity due to the high torque capability of the hydraulic motor. As such, it can be particularly useful in applications where shock loads occur with some frequency, or where many starts and stops are needed. Application of the Hagglund drive to power one of the world`s largest apron feeders in the Alberta Oil Sands is described as an illustration of the exceptional reliability, productivity and performance of this equipment. It has about one five-hundredth of the inertia of an equivalent high speed drive with gear reducer, a feature which is particularly significant in the case of feeders which are known to suffer much downtime due to chain related problems. These types of drives have also been used to great advantage in the process industries like pulp and paper, chemical, rubber and plastics, recycling and steel. 1 tab., 1 fig.

  14. A look at one of the world's largest apron feeder drives - Alberta Oil Sands Project

    Energy Technology Data Exchange (ETDEWEB)

    Persson, O. (Hagglunds Drives Canada Inc., Vancouver, BC (Canada))

    1999-01-01

    Various types of equipment to transport tar sands to processing plants are discussed, with special attention to the advantages of hydraulic direct drives over conventional electro-mechanical drives. A hydraulic direct drive such as the Hagglund Drive has exceptional starting torque capacity due to the high torque capability of the hydraulic motor. As such, it can be particularly useful in applications where shock loads occur with some frequency, or where many starts and stops are needed. Application of the Hagglund drive to power one of the world's largest apron feeders in the Alberta Oil Sands is described as an illustration of the exceptional reliability, productivity and performance of this equipment. It has about one five-hundredth of the inertia of an equivalent high speed drive with gear reducer, a feature which is particularly significant in the case of feeders which are known to suffer much downtime due to chain related problems. These types of drives have also been used to great advantage in the process industries like pulp and paper, chemical, rubber and plastics, recycling and steel. 1 tab., 1 fig.

  15. A Review of Power Distribution Test Feeders in the United States and the Need for Synthetic Representative Networks

    Directory of Open Access Journals (Sweden)

    Fernando E. Postigo Marcos

    2017-11-01

    Full Text Available Under the increasing penetration of distributed energy resources and new smart network technologies, distribution utilities face new challenges and opportunities to ensure reliable operations, manage service quality, and reduce operational and investment costs. Simultaneously, the research community is developing algorithms for advanced controls and distribution automation that can help to address some of these challenges. However, there is a shortage of realistic test systems that are publically available for development, testing, and evaluation of such new algorithms. Concerns around revealing critical infrastructure details and customer privacy have severely limited the number of actual networks published and that are available for testing. In recent decades, several distribution test feeders and US-featured representative networks have been published, but the scale, complexity, and control data vary widely. This paper presents a first-of-a-kind structured literature review of published distribution test networks with a special emphasis on classifying their main characteristics and identifying the types of studies for which they have been used. This both aids researchers in choosing suitable test networks for their needs and highlights the opportunities and directions for further test system development. In particular, we highlight the need for building large-scale synthetic networks to overcome the identified drawbacks of current distribution test feeders.

  16. Short communication: Milk meal pattern of dairy calves is affected by computer-controlled milk feeder set-up

    DEFF Research Database (Denmark)

    Jensen, Margit Bak

    2009-01-01

    for a minimum of 2 and 4 portions, respectively, whereas low-fed calves ingested their milk in 2.4 and 4.4 meals for a minimum of 2 and 4 portions, respectively. Calves on a high milk allowance had fewer milk meals over time, whereas calves on a low milk allowance had the same number of milk meals throughout...... milk portions, whereas the other half could ingest the milk in 4 or more daily portions. Data were collected during 3 successive 14-d periods, the first period starting the day after introduction to the feeder at minimum 12 d of age. High-fed calves ingested their milk in 4.0 and 4.9 meals....... Thus, the development from small and frequent milk meals to fewer and larger meals reported by studies of natural suckling was also found among high-fed calves on a computer-controlled milk feeder. Irrespectively of minimum number of milk portions, the low-fed calves had more unrewarded visits...

  17. GROα regulates human embryonic stem cell self-renewal or adoption of a neuronal fate

    Science.gov (United States)

    Krtolica, Ana; Larocque, Nick; Genbacev, Olga; Ilic, Dusko; Coppe, Jean-Philippe; Patil, Christopher K.; Zdravkovic, Tamara; McMaster, Michael; Campisi, Judith; Fisher, Susan J.

    2012-01-01

    Previously we reported that feeders formed from human placental fibroblasts (hPFs) support derivation and long-term self-renewal of human embryonic stem cells (hESCs) under serum-free conditions. Here, we show, using antibody array and ELISA platforms, that hPFs secrete ~6-fold higher amounts of the CXC-type chemokine, GROα, than IMR 90, a human lung fibroblast line, which does not support hESC growth. Furthermore, immunocytochemistry and immunoblot approaches revealed that hESCs express CXCR, a GROα receptor. We used this information to develop defined culture medium for feeder-free propagation of hESCs in an undifferentiated state. Cells passaged as small aggregates and maintained in the GROα-containing medium had a normal karyotype, expressed pluripotency markers, and exhibited apical–basal polarity, i.e., had the defining features of pluripotent hESCs. They also differentiated into the three primary (embryonic) germ layers and formed teratomas in immunocompromised mice. hESCs cultured as single cells in the GROα-containing medium also had a normal karyotype, but they downregulated markers of pluripotency, lost apical–basal polarity, and expressed markers that are indicative of the early stages of neuronal differentiation—βIII tubulin, vimentin, radial glial protein, and nestin. These data support our hypothesis that establishing and maintaining cell polarity is essential for the long-term propagation of hESCs in an undifferentiated state and that disruption of cell–cell contacts can trigger adoption of a neuronal fate. PMID:21396766

  18. In Vitro Differentiation of Human Mesenchymal Stem Cells into Functional Cardiomyocyte-like Cells.

    Science.gov (United States)

    Szaraz, Peter; Gratch, Yarden S; Iqbal, Farwah; Librach, Clifford L

    2017-08-09

    Myocardial infarction and the subsequent ischemic cascade result in the extensive loss of cardiomyocytes, leading to congestive heart failure, the leading cause of mortality worldwide. Mesenchymal stem cells (MSCs) are a promising option for cell-based therapies to replace current, invasive techniques. MSCs can differentiate into mesenchymal lineages, including cardiac cell types, but complete differentiation into functional cells has not yet been achieved. Previous methods of differentiation were based on pharmacological agents or growth factors. However, more physiologically relevant strategies can also enable MSCs to undergo cardiomyogenic transformation. Here, we present a differentiation method using MSC aggregates on cardiomyocyte feeder layers to produce cardiomyocyte-like contracting cells. Human umbilical cord perivascular cells (HUCPVCs) have been shown to have a greater differentiation potential than commonly investigated MSC types, such as bone marrow MSCs (BMSCs). As an ontogenetically younger source, we investigated the cardiomyogenic potential of first-trimester (FTM) HUCPVCs compared to older sources. FTM HUCPVCs are a novel, rich source of MSCs that retain their in utero immunoprivileged properties when cultured in vitro. Using this differentiation protocol, FTM and term HUCPVCs achieved significantly increased cardiomyogenic differentiation compared to BMSCs, as indicated by the increased expression of cardiomyocyte markers (i.e., myocyte enhancer factor 2C, cardiac troponin T, heavy chain cardiac myosin, signal regulatory protein α, and connexin 43). They also maintained significantly lower immunogenicity, as demonstrated by their lower HLA-A expression and higher HLA-G expression. Applying aggregate-based differentiation, FTM HUCPVCs showed increased aggregate formation potential and generated contracting cells clusters within 1 week of co-culture on cardiac feeder layers, becoming the first MSC type to do so. Our results demonstrate that this

  19. [Proliferative capacity of mesenchymal stem cells from human fetal bone marrow and their ability to differentiate into the derivative cell types of three embryonic germ layers].

    Science.gov (United States)

    Wang, Yue-Chun; Zhang, Yuan

    2008-06-25

    Strong proliferative capacity and the ability to differentiate into the derivative cell types of three embryonic germ layers are the two important characteristics of embryonic stem cells. To study whether the mesenchymal stem cells from human fetal bone marrow (hfBM-MSCs) possess these embryonic stem cell-like biological characteristics, hfBM-MSCs were isolated from bone barrows and further purified according to the different adherence of different kinds of cells to the wall of culture flask. The cell cycle of hfBM-MSCs and MSC-specific surface markers such as CD29, CD44, etc were identified using flow cytometry. The expressions of human telomerase reverse transcriptase (hTERT), the embryonic stem cell-specific antigens, such as Oct4 and SSEA-4 were detected with immunocytochemistry at the protein level and were also tested by RT-PCR at the mRNA level. Then, hfBM-MSCs were induced to differentiate toward neuron cells, adipose cells, and islet B cells under certain conditions. It was found that 92.3% passage-4 hfBM-MSCs and 96.1% passage-5 hfBM-MSCs were at G(0)/G(1) phase respectively. hfBM-MSCs expressed CD44, CD106 and adhesion molecule CD29, but not antigens of hematopoietic cells CD34 and CD45, and almost not antigens related to graft-versus-host disease (GVHD), such as HLA-DR, CD40 and CD80. hfBM-MSCs expressed the embryonic stem cell-specific antigens such as Oct4, SSEA-4, and also hTERT. Exposure of these cells to various inductive agents resulted in morphological changes towards neuron-like cells, adipose-like cells, and islet B-like cells and they were tested to be positive for related characteristic markers. These results suggest that there are plenty of MSCs in human fetal bone marrow, and hfBM-MSCs possess the embryonic stem cell-like biological characteristics, moreover, they have a lower immunogenic nature. Thus, hfBM-MSCs provide an ideal source for tissue engineering and cellular therapeutics.

  20. Simulasi Dinamika untuk Menentukan Stabilitas Sistem Tenaga Listrik Menggunakan Thyristor Controlled Braking Resistor pada Sistem IEEE 34 Node Test Feeder

    Directory of Open Access Journals (Sweden)

    Andi Taufiq

    2012-09-01

    Full Text Available Terdapat berbagai macam metode untuk meningkatkan stabilitas sistem  tenaga listrik. Salah satunya adalah dengan menggunakan metode pengereman dinamis (dynamic braking. Generator sinkron sebagai distributed generator yang digerakkan oleh mesin diesel. Pada saat terjadi gangguan pada sistem, digunakan sebuah Thyristor Controlled Braking Resistor (TCBR untuk meredam osilasi yang terjadi. Sistem yang hendak dianalisis dinamika dan stabilitasnnya adalah IEEE 34 node test feeder. Dengan sistem ini diilustrasikan karakteristik dan keefektifan TCBR untuk meredam osilasi frekuensi rendah dan mencegah terjadinya ketidakstabilan transien sistem. Dari hasil analisis diperoleh bahwa dengan adanya penambahan TCBR (Thyristor Controlled Braking Resistor maka respon transien sistem akan menjadi lebih baik. Hal ini ditunjukkan dengan adanya penurunan overshoot dan settling timenya. Dengan demikian sistem akan menuju kondisi stabil dengan lebih cepat setelah terjadi gangguan.

  1. Assessment of in vitro drug resistance of human breast cancer cells subcultured from biopsy specimens

    Czech Academy of Sciences Publication Activity Database

    Krásná, Luboslava; Netíková, I.; Chaloupková, Alena; Taišlová, Eva; Zimovjanová, M.; Veselý, Pavel; Daneš, J.; Petruželka, L.; Matoušková, Eva

    2003-01-01

    Roč. 23, 3B (2003), s. 2593-2600 ISSN 0250-7005 R&D Projects: GA MZd NC6734 Institutional research plan: CEZ:AV0Z5052915 Keywords : Breast cancer * 3T3 feeder-layer culture technique * MTT test Subject RIV: EA - Cell Biology Impact factor: 1.347, year: 2003

  2. Development of an extruder-feeder biomass direct liquefaction process. Volume 2, Parts 4--8: Final report

    Energy Technology Data Exchange (ETDEWEB)

    White, D.H.; Wolf, D. [Arizona Univ., Tucson, AZ (United States). Dept. of Chemical Engineering

    1991-10-01

    As an abundant, renewable, domestic energy resource, biomass could help the United States reduce its dependence on imported oil. Biomass is the only renewable energy technology capable of addressing the national need for liquid transportation fuels. Thus, there is an incentive to develop economic conversion processes for converting biomass, including wood, into liquid fuels. Through research sponsored by the US DOE`s Biomass Thermochemical Conversion Program, the University of Arizona has developed a unique biomass direct liquefaction system. The system features a modified single-screw extruder capable of pumping solid slurries containing as high as 60 wt% wood flour in wood oil derived vacuum bottoms at pressures up to 3000 psi. The extruder-feeder has been integrated with a unique reactor by the University to form a system which offers potential for improving high pressure biomass direct liquefaction technology. The extruder-feeder acts simultaneously as both a feed preheater and a pumping device for injecting wood slurries into a high pressure reactor in the biomass liquefaction process. An experimental facility was constructed and following shakedown operations, wood crude oil was produced by mid-1985. By July 1988, a total of 57 experimental continuous biomass liquefaction runs were made using White Birch wood feedstock. Good operability was achieved at slurry feed rates up to 30 lb/hr, reactor pressures from 800 to 3000 psi and temperatures from 350{degree}C to 430{degree}C under conditions covering a range of carbon monoxide feed rates and sodium carbonate catalyst addition. Crude wood oils containing as little as 6--10 wt% residual oxygen were produced. 38 refs., 82 figs., 26 tabs.

  3. Feeding current characteristics of three morphologically different bivalve suspension feeders, Crassostrea gigas, Mytilus edulis and Cerastoderma edule, in relation to food competition

    NARCIS (Netherlands)

    Troost, K.; Stamhuis, E.J.; van Duren, L.A; Wolff, W.J.

    Introduced Pacific oysters (Crassostrea gigas) have shown rapid expansion in the Oosterschelde estuary, while stocks of native bivalves declined slightly or remained stable. This indicates that they might have an advantage over native bivalve filter feeders. Hence, at the scale of individual

  4. 47 CFR 25.223 - Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Technical Standards § 25...

  5. 47 CFR 25.258 - Sharing between NGSO MSS Feeder links Stations and GSO FSS services in the 29.25-29.5 GHz Bands.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Sharing between NGSO MSS Feeder links Stations and GSO FSS services in the 29.25-29.5 GHz Bands. 25.258 Section 25.258 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Technical Standards § 25...

  6. Network integration modelling of feeder and BRT(bus rapid transit) to reduce the usage of private vehicles in Palembang’s suburban area

    Science.gov (United States)

    Nur'afalia, D.; Afifa, F.; Rubianto, L.; Handayeni, K. D. M. E.

    2018-01-01

    The aim of this research is to determine the optimal feeder network route that integrates with BRT (Bus Rapid Transit). Palembang, a high growing population city with unresolved transportation demand sector. BRT as main public transportation could not fulfill people’s demand in transportation, especially in Alang-Alang Lebar sub-district. As an impact, the usage of private vehicles increases along the movement toward the city center. The concept of Network Integration that integrates feeder network with BRT is expected to be a solution to suppress the rate of private vehicles’ usage and to improve public transportation service, so that the use of BRT will be increased in the suburban area of Palembang. The method used to identifying the optimal route using Route Analysis method is route analysis using Tranetsim 0.4. The best route is obtained based on 156 movement samples. The result is 58,7% from 199 mobility’s potency of private vehicle usage’s can be reduced if there is a feeder network’s route in Alang-Alang Lebar’s sub-district. From the result, the existance of integration between feeder network and BRT is potential enough to reduce the usage of private vehicles and supports the sustainability of transportation mobility in Palembang City.

  7. Feeding current characteristics of three morphologically different bivalve suspension feeders, Crassostrea gigas Mytilus edulis and Cerastoderma edule , in relation to food competition

    NARCIS (Netherlands)

    Troost, K.; Stamhuis, E.J.; Duren, L.A.; Wolff, W.

    2009-01-01

    Introduced Pacific oysters (Crassostrea gigas) have shown rapid expansion in the Oosterschelde estuary, while stocks of native bivalves declined slightly or remained stable. This indicates that they might have an advantage over native bivalve filter feeders. Hence, at the scale of individual

  8. Effect of stall design on dairy calf transition to voluntary feeding on an automatic milk feeder after introduction to group housing.

    Science.gov (United States)

    Wilson, Tanya R; LeBlanc, Stephen J; DeVries, Trevor J; Haley, Derek B

    2018-06-01

    Automatic milk feeders (AMF) for young dairy calves are widely used in the dairy industry. These feeders are thought to have benefits for calf health and welfare and may reduce labor required for feeding; however, little is known about how calves adapt to feeding with AMF. The objective of this study was to observe the effects of feeding stall design on calves learning to use the AMF. The hypothesis was that solid side stalls, compared with steel bar stalls, would result in a longer latency to approach and feed from the AMF without assistance. A total of 147 Holstein calves (80 male and 67 female) were enrolled at 4 d of age, introduced to a group pen, and, at the same time, trained on an AMF. For training, calves were allowed to suck on the trainer's fingers and guided to the teat. Calves were allocated to 1 of 2 stall designs at the pen level, depending on which treatment cohort they were born into, either with steel bar stall walls (n = 46 male, 34 female calves) or with solid side stall walls (n = 34 male, 33 female calves). For 72 h after introductory training on the AMF, data from the feeders were collected and calf behavior was monitored by video. Outcomes measured included latency to first voluntary visit to the feeder and to first feeding, time spent in the feeder, amount of milk consumed over 72 h, number of retraining sessions required (retrained if linear regression models or a Poisson model for the outcome of retraining. For certain outcomes the effects of stall design interacted with difficulty of training (willingness to enter feeder and drink); for the 38% of calves that were scored as moderately difficult to train on a scale of easy, moderate, or difficult, treatment (stall design) differences were detected. These calves took 2× longer to lick or bite toward the nipple, 2× longer to first voluntarily feeding, and consumed less milk over 72 h following training when trained on the steel bar stall design. These results suggest simple features of a

  9. Flow visualization study of two phase flow in a single bend outlet feeder pipe and horizontal annulus of outlet end-fitting of a CANDU reactor

    International Nuclear Information System (INIS)

    Supa-Amornkul, S.; Lister, D.H.; Steward, F.R.

    2005-01-01

    'Full text:' In CANDU-6 reactors, the pressurized high-temperature coolant flows through 380 fuel channels passing horizontally through the core. Each end of a fuel channel has a stainless steel annular end-fitting connected to a carbon steel feeder pipe. The outlet coolant, which is at 310 o C with up to 0.30 steam voidage, turns through 90 o as it passes from flow in the annular end-fitting to pipe flow in the feeder via a Grayloc connector. Since 1996, several CANDU stations have reported excessive corrosion of their outlet feeder pipes; especially between the first metre, which consisted of single or double bends. Early studies related the attack to the hydrodynamics of the coolant and verified that it was a type of flow accelerated corrosion. In order to understand the hydrodynamics of the coolant in the outlet feeders by flow-visualization, a full-scale transparent test section simulating the geometry and orientation of an outlet feeder bend with its upstream annular end-fitting were fabricated. The feeder consisted of a 54 mm inside diameter acrylic pipe with a 73 o bend, connecting to an acrylic simulation of a Grayloc flanged fitting and annular end-fitting. The annular end-fitting consisted of an inner pipe, 110 mm outer diameter, and an outer pipe, 150 mm inner diameter, both 190.7 cm long in length. The tests were performed with water and air at atmospheric pressure and room temperature. The maximum water volumetric flow rate was 19 L/s and the volume fraction of air varied from 0.05 to 0.56. The phase distributions within the feeder pipe and along the length of the annulus were investigated with a digital video recorder. Size, concentration and velocity of the air bubbles at particular locations were studied with a high-speed digital still camera and a high-speed digital video camera. Phase distributions and variations in bubble size with velocity were determined. Particular attention was paid to the flow pattern at the inside of the bend, where a CFD

  10. Flow visualization study of two phase flow in a single bend outlet feeder pipe and horizontal annulus of outlet end-fitting of a CANDU reactor

    Energy Technology Data Exchange (ETDEWEB)

    Supa-Amornkul, S.; Lister, D.H.; Steward, F.R. [Univ. of New Brunswick, Fredericton, New Brunswick (Canada)]. E-mail: h796e@unb.ca; dlister@unb.ca; fsteward@unb.ca

    2005-07-01

    'Full text:' In CANDU-6 reactors, the pressurized high-temperature coolant flows through 380 fuel channels passing horizontally through the core. Each end of a fuel channel has a stainless steel annular end-fitting connected to a carbon steel feeder pipe. The outlet coolant, which is at 310{sup o}C with up to 0.30 steam voidage, turns through 90{sup o} as it passes from flow in the annular end-fitting to pipe flow in the feeder via a Grayloc connector. Since 1996, several CANDU stations have reported excessive corrosion of their outlet feeder pipes; especially between the first metre, which consisted of single or double bends. Early studies related the attack to the hydrodynamics of the coolant and verified that it was a type of flow accelerated corrosion. In order to understand the hydrodynamics of the coolant in the outlet feeders by flow-visualization, a full-scale transparent test section simulating the geometry and orientation of an outlet feeder bend with its upstream annular end-fitting were fabricated. The feeder consisted of a 54 mm inside diameter acrylic pipe with a 73{sup o} bend, connecting to an acrylic simulation of a Grayloc flanged fitting and annular end-fitting. The annular end-fitting consisted of an inner pipe, 110 mm outer diameter, and an outer pipe, 150 mm inner diameter, both 190.7 cm long in length. The tests were performed with water and air at atmospheric pressure and room temperature. The maximum water volumetric flow rate was 19 L/s and the volume fraction of air varied from 0.05 to 0.56. The phase distributions within the feeder pipe and along the length of the annulus were investigated with a digital video recorder. Size, concentration and velocity of the air bubbles at particular locations were studied with a high-speed digital still camera and a high-speed digital video camera. Phase distributions and variations in bubble size with velocity were determined. Particular attention was paid to the flow pattern at the inside

  11. Effect of feeder space during the growing and laying periods and the rate of feed increase at the onset of lay on broiler breeder female reproductive function.

    Science.gov (United States)

    Leksrisompong, N; Romero-Sanchez, H; Oviedo-Rondón, E O; Brake, J

    2014-07-01

    A study was conducted to examine how 2 feeder space allocations during the rearing period followed by 2 feeder space allocations after photostimulation and 2 female feeding to peak programs (fast or slow) affected female broiler breeder reproductive performance and mortality. Sixteen pens of 76 breeder females each were equipped with either 4 tube feeders with a 132 cm circumference pan (7.0 cm/female) or 6 feeders (10.4 cm/female) to 21 wk of age. Thereafter, 64 females were moved to breeding pens, photostimulated, and fed sex-separate from either 3 (6.2 cm/female) or 5 (10.3 cm/female) feeders with either fast or slow feeding to peak feeding programs applied to complete a 2 × 2 × 2 factorial design. Seven males that were separately reared in a similar manner were added per pen. Individual female BW was determined at 6, 20, and 32 wk of age and BW uniformity assessed. Greater feeder space during rearing increased BW at 32 wk of age, whereas greater feeder space during lay or slow feeding to peak decreased BW at 32 wk. There were no differences in BW uniformity. Hens from the 10.4 to 10.3 cm/female combination produced a significantly greater number of eggs as compared with the 7.0 to 10.3 cm/female and 10.4 to 6.2 cm/female combinations with the 7.0 to 6.2 cm/female combination intermediate. Percentage hen-day egg production of the 10.4 to 10.3 cm/female combination hens was significantly greater than all other combinations. Livability was improved in the 10.4 to 10.3 cm/female combination relative to the 7.0 to 10.3 cm/female combination with the others intermediate. The fast feeding to peak program increased yolk weight as well as yolk:albumen ratio at 28 and 30 wk of age, but egg weight did not differ. These data indicated that increased or decreased feeder space between the growing and laying periods did not affect broiler breeder female BW, uniformity, egg weight, fertility, or hatchability. The 10.3 cm/female laying feeder space exhibited the best hen

  12. The effect of a hay grid feeder on feed consumption and measurement of the gastric pH using an intragastric electrode device in horses: a preliminary report.

    Science.gov (United States)

    Aristizabal, F; Nieto, J; Yamout, S; Snyder, J

    2014-07-01

    Obesity and gastric ulceration are highly prevalent in horses. Management modifications for preventing squamous gastric ulceration include frequent feeding and free access to pasture; however, these practices may predispose horses to obesity. To compare the percentage of hay consumed, intragastric pH and horse activity between feeding from the ground and a hay grid feeder. Crossover experimental study. A pH electrode was inserted into the stomach to record the intragastric pH for 48 h. Horses received 1% of their body weight in grass hay twice a day. Horses were assigned to be fed from the ground or a commercial hay grid feeder for 24 h and then switched to the opposite protocol for an additional 24 h. Horses were continuously video-recorded and the percentage of time spent eating or drinking, walking or standing, and lying down were calculated. Two point data were compared by paired t test and pH over time was compared by repeated measures ANOVA. Horses consumed significantly greater amounts of grass hay when fed on the ground compared with a hay grid feeder (n = 9; PpH values (n = 6; P = 0.97), mean intragastric pH over time (n = 6; P = 0.45) the length of time the pH was below 4.0 (n = 6; P = 0.54), and the percentage of time horses spent eating or drinking (n = 9; P = 0.52), walking or standing (n = 9; P = 0.3), or lying down (n = 9; P = 0.4). Within each group horses spent more time eating during the day compared with the night (n = 9; hay grid feeder P = 0.003; ground feeding P = 0.007). The hay grid feeder studied may be used to reduce the amount of hay ingested by horses without reducing the time horses spend eating. © 2013 EVJ Ltd.

  13. Assessment of Fuel Analysis Methodology and Fission Product Release for 37-Element Fuel by Using the Latest IST Codes during Stagnation Feeder Break in CANDU

    International Nuclear Information System (INIS)

    Park, Joo Hwan; Jung, Jong Yeob

    2009-09-01

    Feeder break accident is regarded as one of the design basis accident in CANDU reactor which results in a fuel failure. For a particular range of inlet feeder break sizes, the flow in the channel is reduced sufficiently that the fuel and fuel channel integrity can be significantly affected to have damage in the affected channel, while the remainder of the core remains adequately cooled. The flow in the downstream channel can be more or less stagnated due to a balance between pressure at the break on the upstream side and the reverse driving pressure between the break and the downstream end. In the extreme, this can lead to rapid fuel heatup and fuel damage and failure of the fuel channel similar to that associated with a severe channel flow blockage. Such an inlet feeder break scenario is called a stagnation break. In this report, the fuel analysis methodology and the assessment results of fission product inventory and release during the stagnation feeder break are described for conservatively assumed limiting channel. The accident was assumed to be occurred in the refurbished Wolsong unit 1 and the latest safety codes were used in the analysis. Fission product inventories during the steady state were calculated by using ELESTRES-IST 1.2 code. The whole analysis process was carried out by a script file which was programmed by Perl language. The perl script file was programmed to make all ELESTRES input files for each bundle and each ring based on the given power-burnup history and thermal-hydraulic conditions of the limiting channel and to perform the fuel analysis automatically. The fission product release during the transient period of stagnation feeder break was evaluated by applying Gehl model. The amounts of each isotope's release are conservatively evaluated for additional 2 seconds after channel failure. The calculated fission product releases are provided to the following dose assessment as a source term

  14. Layered materials

    Science.gov (United States)

    Johnson, David; Clarke, Simon; Wiley, John; Koumoto, Kunihito

    2014-06-01

    Layered compounds, materials with a large anisotropy to their bonding, electrical and/or magnetic properties, have been important in the development of solid state chemistry, physics and engineering applications. Layered materials were the initial test bed where chemists developed intercalation chemistry that evolved into the field of topochemical reactions where researchers are able to perform sequential steps to arrive at kinetically stable products that cannot be directly prepared by other approaches. Physicists have used layered compounds to discover and understand novel phenomena made more apparent through reduced dimensionality. The discovery of charge and spin density waves and more recently the remarkable discovery in condensed matter physics of the two-dimensional topological insulating state were discovered in two-dimensional materials. The understanding developed in two-dimensional materials enabled subsequent extension of these and other phenomena into three-dimensional materials. Layered compounds have also been used in many technologies as engineers and scientists used their unique properties to solve challenging technical problems (low temperature ion conduction for batteries, easy shear planes for lubrication in vacuum, edge decorated catalyst sites for catalytic removal of sulfur from oil, etc). The articles that are published in this issue provide an excellent overview of the spectrum of activities that are being pursued, as well as an introduction to some of the most established achievements in the field. Clusters of papers discussing thermoelectric properties, electronic structure and transport properties, growth of single two-dimensional layers, intercalation and more extensive topochemical reactions and the interleaving of two structures to form new materials highlight the breadth of current research in this area. These papers will hopefully serve as a useful guideline for the interested reader to different important aspects in this field and

  15. Development of human umbilical vein endothelial cell (HUVEC) and human umbilical vein smooth muscle cell (HUVSMC) branch/stem structures on hydrogel layers via biological laser printing (BioLP)

    International Nuclear Information System (INIS)

    Wu, P K; Ringeisen, B R

    2010-01-01

    Angiogenesis is one of the prerequisite steps for viable tissue formation. The ability to influence the direction and structure in the formation of a vascular system is crucial in engineering tissue. Using biological laser printing (BioLP), we fabricated branch/stem structures of human umbilical vein endothelial cells (HUVEC) and human umbilical vein smooth muscle cells (HUVSMC). The structure is simple as to mimic vascular networks in natural tissue but also allow cells to develop new, finer structures away from the stem and branches. Additionally, we printed co-culture structures by first depositing only HUVECs, followed by 24 h incubation to allow for adequate cell-cell communication and differentiation into lumina; these cell printed scaffold layers were then removed from incubation and inserted into the BioLP apparatus so that HUVSMCs could be directly deposited on top and around the previously printed HUVEC structures. The growth and differentiation of these co-culture structures was then compared to the growth of printed samples with either HUVECs or HUVSMCs alone. Lumen formation was found to closely mimic the original branch and stem structure. The beginning of a network structure is observed. HUVSMCs acted to limit HUVEC over-growth and migration when compared to printed HUVEC structures alone. HUVSMCs and HUVECS, when printed in close contact, appear to form cell-cell junctions around lumen-like structures. They demonstrate a symbiotic relationship which affects their development of phenotype when in close proximity of each other. Our results indicate that it is possible to direct the formation and growth of lumen and lumen network using BioLP.

  16. Bird feeders may sustain feral Rose-ringed parakeets Psittacula krameri in temperate Europe

    OpenAIRE

    Clergeau , Philippe; Vergnes , Alan

    2011-01-01

    International audience; The Rose-ringed parakeet Psittacula krameri, a bird species of subtropical origin, has established feral populations in temperate Europe. We analysed the feeding habits of Rose-ringed parakeets near Paris, France, in order to assess if food provided by humans might contribute to the success of this invasive bird species. We considered 87 feeding events performed during 2002 -2007 and 247 feeding events performed during March -November 2008. We recorded the consumption ...

  17. Gene expression studies on human keratinocytes transduced with human growth hormone gene for a possible utilization in gene therapy

    International Nuclear Information System (INIS)

    Mathor, Monica Beatriz.

    1994-01-01

    Taking advantage of the recent progress in the DNA-recombinant techniques and of the potentiality of normal human keratinocytes primary culture to reconstitute the epidermis, it was decided to genetically transform these keratinocytes to produce human growth hormone under controllable conditions that would be used in gene therapy at this hormone deficient patients. The first step to achieve this goal was to standardize infection of keratinocytes with retrovirus producer cells containing a construct which included the gene of bacterial b-galactosidase. The best result was obtained cultivating the keratinocytes for 3 days in a 2:1 mixture of retrovirus producer cells and 3T3-J2 fibroblasts irradiated with 60 Gy, and splitting these infected keratinocytes on 3T3-J2 fibroblasts feeder layer. Another preliminary experiment was to infect normal human keratinocytes with interleukin-6 gene (hIL-6) that, in pathologic conditions, could be reproduced by keratinocytes and secreted to the blood stream. Thus, we verify that infected keratinocytes secrete an average amount of 500 ng/10 6 cell/day of cytokin during the in vitro life time, that certify the stable character of the injection. These keratinocytes, when grafted in mice, secrete hIL-6 to the blood stream reaching levels of 40 pg/ml of serum. After these preliminary experiments, we construct a retroviral vector with the human growth hormone gene (h GH) driven by human metallothionein promoter (h PMT), designated DChPMTGH. Normal human keratinocytes were infected with DChPMTGH producer cells, following previously standardized protocol, obtaining infected keratinocytes secreting to the culture media 340 ng h GH/10 6 cell/day without promoter activation. This is the highest level of h GH secreted in human keratinocytes primary culture described in literature. The h GH value increases approximately 10 times after activation with 100 μM Zn +2 for 8-12 hours. (author). 158 refs., 42 figs., 6 tabs

  18. Earth's ozone layer

    International Nuclear Information System (INIS)

    Lasa, J.

    1991-01-01

    The paper contain the actual results of investigations of the influence of the human activity on the Earth's ozone layer. History of the ozone measurements and of the changes in its concentrations within the last few years are given. The influence of the trace gases on both local and global ozone concentrations are discussed. The probable changes of the ozone concentrations are presented on the basis of the modelling investigations. The effect of a decrease in global ozone concentration on human health and on biosphere are also presented. (author). 33 refs, 36 figs, 5 tabs

  19. Low calcium culture condition induces mesenchymal cell-like phenotype in normal human epidermal keratinocytes

    International Nuclear Information System (INIS)

    Takagi, Ryo; Yamato, Masayuki; Murakami, Daisuke; Sugiyama, Hiroaki; Okano, Teruo

    2011-01-01

    Highlights: → Normal human epidermal keratinocytes serially cultured under low calcium concentration were cytokeratin and vimentin double positive cells. → The human keratinocytes expressed some epithelial stem/progenitor cell makers, mesenchymal cell markers, and markers of epithelial-mesenchymal transition. → Mesenchymal cell-like phenotype in the keratinocytes was suppressed under high-calcium condition. -- Abstract: Epithelial-mesenchymal transition (EMT) is an important cellular phenomenon in organ developments, cancer invasions, and wound healing, and many types of transformed cell lines are used for investigating for molecular mechanisms of EMT. However, there are few reports for EMT in normal human epithelial cells, which are non-transformed or non-immortalized cells, in vitro. Therefore, normal human epidermal keratinocytes (NHEK) serially cultured in low-calcium concentration medium (LCM) were used for investigating relations between differentiation and proliferation and mesenchymal-like phenotype in the present study, since long-term cultivation of NHEK is achieved in LCM. Interestingly, NHEK serially cultured in LCM consisted essentially of cytokeratin-vimentin double positive cells (98%), although the NHEK exhibited differentiation under high-calcium culture condition with 3T3 feeder layer. The vimentin expression was suppressed under high-calcium condition. These results may indicate the importance of mesenchymal-like phenotype for serially cultivation of NHEK in vitro.

  20. Human corneal epithelial subpopulations

    DEFF Research Database (Denmark)

    Søndergaard, Chris Bath

    2013-01-01

    Corneal epithelium is being regenerated throughout life by limbal epithelial stem cells (LESCs) believed to be located in histologically defined stem cell niches in corneal limbus. Defective or dysfunctional LESCs result in limbal stem cell deficiency (LSCD) causing pain and decreased visual acuity...... subpopulations in human corneal epithelium using a combination of laser capture microdissection and RNA sequencing for global transcriptomic profiling. We compared dissociation cultures, using either expansion on γ-irradiated NIH/3T3 feeder cells in serum-rich medium or expansion directly on plastic in serum...

  1. Comparison of the Ex Vivo Expansion of UCB-Derived CD34+ in 3D DBM/MBA Scaffolds with USSC as a Feeder Layer

    Directory of Open Access Journals (Sweden)

    Zahra Sadat Hashemi

    2013-10-01

    Because of acid extraction in the DBM production process, mineral materials were removed and the protein background that was more flexible was presented. Therefore these results suggest that USSC-DBM can be a suitable ex vivo mimicry niche by intensifying of surface/volume ratio and supporting the stem cell differentiation and expansion.

  2. Artificial blood feeders for mosquito and ticks-Where from, where to?

    Science.gov (United States)

    Romano, Donato; Stefanini, Cesare; Canale, Angelo; Benelli, Giovanni

    2018-07-01

    Mosquito and tick feeding activity represent a key threat for humans, livestock, pets and wildlife worldwide. Rearing these vectors in laboratory conditions is extremely important to investigate basic facets of their biology, vector competence, new control strategies, as well as mechanisms of pesticide resistance. However, the use of animals or humans to provide blood for hematophagous arthropod feeding poses a strict limit to these researches, due to the accidental transmission of diseases, ethical problems concerning animal welfare, as well as expensive and time-consuming animal rearing procedures. The use of devices to artificially feed arthropod vectors can importantly leverage progresses in parasitology and entomology. The aim of this review is to summarize current knowledge about artificial feeding of mosquitoes and ticks, focusing on key concepts and case studies about the design and fabrication of blood feeding devices. From a technical standpoint, the literature analyzed here showed little standardization of materials used for fabricating membrane interfaces, as well as in the strategy used to heat the "biomimetic host". In addition, a lack of uniform methods to design an architecture merging complex and realistic cues with an easy-to-assemble approach have been found. Some commercial products are available, but they are quite expensive, thus hard to reach for many laboratories, especially in developing countries. An important challenge for future research is represented by the introduction of automation and bioinspired engineered solutions in these devices, improving the effectiveness of blood-feeding systems by increasing their host-mimicking features. Automation can reduce labor costs and provide interesting solutions - in line with the 3R principle "reduce, replace and refine" - aimed to minimize the employ of experimental animals in research. Copyright © 2018 Elsevier B.V. All rights reserved.

  3. Optimation of Operation System Integration between Main and Feeder Public Transport (Case Study: Trans Jakarta-Kopaja Bus Services)

    Science.gov (United States)

    Miharja, M.; Priadi, Y. N.

    2018-05-01

    Promoting a better public transport is a key strategy to cope with urban transport problems which are mostly caused by a huge private vehicle usage. A better public transport service quality not only focuses on one type of public transport mode, but also concerns on inter modes service integration. Fragmented inter mode public transport service leads to a longer trip chain as well as average travel time which would result in its failure to compete with a private vehicle. This paper examines the optimation process of operation system integration between Trans Jakarta Bus as the main public transport mode and Kopaja Bus as feeder public transport service in Jakarta. Using scoring-interview method combined with standard parameters in operation system integration, this paper identifies the key factors that determine the success of the two public transport operation system integrations. The study found that some key integration parameters, such as the cancellation of “system setoran”, passenger get in-get out at official stop points, and systematic payment, positively contribute to a better service integration. However, some parameters such as fine system, time and changing point reliability, and information system reliability are among those which need improvement. These findings are very useful for the authority to set the right strategy to improve operation system integration between Trans Jakarta and Kopaja Bus services.

  4. From steep feeders to tabular plutons - Emplacement controls of syntectonic granitoid plutons in the Damara Belt, Namibia

    Science.gov (United States)

    Hall, Duncan; Kisters, Alexander

    2016-01-01

    Granitoid plutons in the deeply eroded south Central Zone of the Damara Belt in Namibia commonly show tabular geometries and pronounced stratigraphic controls on their emplacement. Subhorizontal, sheet-like pluton geometries record emplacement during regional subhorizontal shortening, but the intrusion of spatially and temporally closely-related granitoid plutons at different structural levels and in distinct structural settings suggests independent controls on their levels of emplacement. We describe and evaluate the controls on the loci of the dyke-to-sill transition that initiated the emplacement of three syntectonic (560-530 Ma) plutons in the basement-cover stratigraphy of the Erongo region. Intrusive relationships highlight the significance of (1) rigidity anisotropies associated with competent sedimentary packages or pre-existing subhorizontal granite sheets and (2) rheological anisotropies associated with the presence of thick ductile marble horizons. These mechanical anisotropies may lead to the initial deflection of steep feeder conduits as well as subsequent pluton assembly by the repeated underaccretion of later magma batches. The upward displacement of regional isotherms due to the heat advection associated with granite emplacement is likely to have a profound effect on the mechanical stratification of the upper crust and, consequently, on the level at which granitoid pluton emplacement is initiated. In this way, pluton emplacement at progressively shallower crustal depths may have resulted in the unusually high apparent geothermal gradients recorded in the upper crustal levels of the Damara Belt during its later evolution.

  5. Bacterial Feeders, the Nematode Caenorhabditis elegans and the Flagellate Cercomonas longicauda, have different Effects on Outcome of Competition among the Pseudomonas Biocontrol Strains CHA0 and DSS73

    DEFF Research Database (Denmark)

    Pedersen, Annette; Nybroe, Ole; Winding, Anne

    2009-01-01

    How bacterial feeding fauna affects colonization and survival of bacteria in soil is not well understood, which constrains the applicability of bacterial inoculants in agriculture. This study aimed to unravel how food quality of bacteria and bacterial feeders with different feeding habits (the......50090 or one of two biocontrol strains P. fluorescens CHA0 or Pseudomonas sp. DSS73) or combinations of two bacterial strains. DSM50090 is a suitable food bacterium, DSS73 is of intermediate food quality, and CHA0 is inedible to the bacterial feeders. Bacterial and protozoan cell numbers were measured...... predation pressure. Hence, the results suggested that the outcome of competition among bacteria depended on their ability to cope with the prevailing bacterial predator....

  6. THE METHOD OF SELECTION OF THE SETPOINT HIGH SPEED FEEDER SWITCH OF 3,3KV DC WITH MICROPROCESSOR-BASED PROTECTION SYSTEMS

    Directory of Open Access Journals (Sweden)

    P. Ye. Mykhalichenko

    2009-10-01

    Full Text Available In the article a new procedure of choice of minimum current jump for action of fast-acting switches of 3.3 kV DC traction substations intended for the use in the microprocessor protection system of feeders is described. This procedure is more perfect than existing one on the current increment and uses the results of mathematical simulation of the traction electric supply system.

  7. Differentiation of monkey embryonic stem cells to hepatocytes by feeder-free dispersion culture and expression analyses of cytochrome p450 enzymes responsible for drug metabolism.

    Science.gov (United States)

    Maruyama, Junya; Matsunaga, Tamihide; Yamaori, Satoshi; Sakamoto, Sakae; Kamada, Noboru; Nakamura, Katsunori; Kikuchi, Shinji; Ohmori, Shigeru

    2013-01-01

    We reported previously that monkey embryonic stem cells (ESCs) were differentiated into hepatocytes by formation of embryoid bodies (EBs). However, this EB formation method is not always efficient for assays using a large number of samples simultaneously. A dispersion culture system, one of the differentiation methods without EB formation, is able to more efficiently provide a large number of feeder-free undifferentiated cells. A previous study demonstrated the effectiveness of the Rho-associated kinase inhibitor Y-27632 for feeder-free dispersion culture and induction of differentiation of monkey ESCs into neural cells. In the present study, the induction of differentiation of cynomolgus monkey ESCs (cmESCs) into hepatocytes was performed by the dispersion culture method, and the expression and drug inducibility of cytochrome P450 (CYP) enzymes in these hepatocytes were examined. The cmESCs were successfully differentiated into hepatocytes under feeder-free dispersion culture conditions supplemented with Y-27632. The hepatocytes differentiated from cmESCs expressed the mRNAs for three hepatocyte marker genes (α-fetoprotein, albumin, CYP7A1) and several CYP enzymes, as measured by real-time polymerase chain reaction. In particular, the basal expression of cmCYP3A4 (3A8) in these hepatocytes was detected at mRNA and enzyme activity (testosterone 6β-hydroxylation) levels. Furthermore, the expression and activity of cmCYP3A4 (3A8) were significantly upregulated by rifampicin. These results indicated the effectiveness of Y-27632 supplementation for feeder-free dispersed culture and induction of differentiation into hepatocytes, and the expression of functional CYP enzyme(s) in cmESC-derived hepatic cells.

  8. Natural melanin composites by layer-by-layer assembly

    Science.gov (United States)

    Eom, Taesik; Shim, Bong Sub

    2015-04-01

    Melanin is an electrically conductive and biocompatible material, because their conjugated backbone structures provide conducting pathways from human skin, eyes, brain, and beyond. So there is a potential of using as materials for the neural interfaces and the implantable devices. Extracted from Sepia officinalis ink, our natural melanin was uniformly dispersed in mostly polar solvents such as water and alcohols. Then, the dispersed melanin was further fabricated to nano-thin layered composites by the layer-by-layer (LBL) assembly technique. Combined with polyvinyl alcohol (PVA), the melanin nanoparticles behave as an LBL counterpart to from finely tuned nanostructured films. The LBL process can adjust the smart performances of the composites by varying the layering conditions and sandwich thickness. We further demonstrated the melanin loading degree of stacked layers, combination nanostructures, electrical properties, and biocompatibility of the resulting composites by UV-vis spectrophotometer, scanning electron microscope (SEM), multimeter, and in-vitro cell test of PC12, respectively.

  9. A Frequency-Based Assignment Model under Day-to-Day Information Evolution of Oversaturated Conditions on a Feeder Bus Service

    Directory of Open Access Journals (Sweden)

    Silin Zhang

    2017-02-01

    Full Text Available Day-to-day information is increasingly being implemented in transit networks worldwide. Feeder bus service (FBS plays a vital role in a public transit network by providing feeder access to hubs and rails. As a feeder service, a space-time path for frequent passengers is decided by its dynamic strategy procedure, in which a day-to-day information self-learning mechanism is identified and analyzed from our survey data. We formulate a frequency-based assignment model considering day-to-day evolution under oversaturated conditions, which takes into account the residual capacity of bus and the comfort feelings of sitting or standing. The core of our proposed model is to allocate the passengers on each segment belonging to their own paths according to multi-utilities transformed from the time values and parametric demands, such as frequency, bus capacity, seat comfort, and stop layout. The assignment method, albeit general, allows us to formulate an equivalent optimization problem in terms of interaction between the FBS’ operation and frequent passengers’ rational behaviors. Finally, a real application case is generated to test the ability of the modeling framework capturing the theoretical consequents, serving the passengers’ dynamic externalities.

  10. Limited similarity between plasmids encoding CTX-M-1 β-lactamase in Escherichia coli from humans, pigs, cattle, organic poultry layers and horses in Denmark

    DEFF Research Database (Denmark)

    Jakobsen, Lotte; Bortolaia, Valeria; Bielak, Eliza Maria

    2015-01-01

    in Denmark between 2006 and 2010. In total, 65 CTX-M-1-producing isolates from patients (n=22), pigs (n=21), cattle (n=4), organic poultry layers (n=3) and horses (n=15) were typed by pulsed-field gel electrophoresis (PFGE). Plasmids harbouring blaCTX-M-1 were characterised by S1 PFGE, PCR-based replicon...

  11. The comparison of two methods to obtain human oral keratinocytes in primary culture

    International Nuclear Information System (INIS)

    Klingbeil, Maria Fatima Guarizo

    2006-01-01

    The therapeutic procedures frequently used in oral treatments for the pathological diseases are surgical, resulting in failures of the mucosal continuity.The possibility to obtain transplantable oral epithelia from an in vitro cell culture opens new utilization perspectives not only to where it comes from, but also as a reconstructive material for other parts of the human body, such as: urethra, epithelia corneo-limbal, cornea, ocular surface. Many researchers still use controversial methods for obtaining cells. It was therefore evaluated and compared the efficiency in both methods: enzymatic and direct explant to obtain oral keratinocytes from human oral mucosa. Fragments of intra oral epithelial tissues from healthy human subjects, undergoing dental surgeries, were donated to the research project. The keratinocytes were cultivated over a feeder-layer from a previously irradiated 3T3 Swiss albino fibroblasts. In this study it was compared the time needed in the cell obtention, the best cell amount between both methods, the life-span, the cell capacity to form an in vitro epithelia and its morphologic structure. The results in the assessment of both methods have shown the possibility to obtain keratinocytes from a small oral fragment, but at the same time we may verify the advantages and peculiar restrictions for each one of both analyzed methods. (author)

  12. Mixed xylem and phloem sap ingestion in sheath-feeders as normal dietary behavior: Evidence from the leafhopper Scaphoideus titanus.

    Science.gov (United States)

    Chuche, Julien; Sauvion, Nicolas; Thiéry, Denis

    2017-10-01

    In phytophagous piercing-sucking insects, salivary sheath-feeding species are often described as xylem- or phloem-sap feeding specialists. Because these two food sources have very different characteristics, two feeding tactics are often associated with this supposed specialization. Studying the feeding behavior of insects provides substantial information on their biology, ecology, and evolution. Furthermore, study of feeding behavior is of primary importance to elucidate the transmission ability of insects that act as vectors of plant pathogens. In this study, we compared the durations of ingestion performed in xylem versus phloem by a leafhopper species, Scaphoideus titanus Ball, 1932. This was done by characterizing and statistically analyzing electrical signals recorded using the electropenetrography technique, derived from the feeding behaviors of males and females. We identified three groups of S. titanus based on their feeding behavior: 1) a group that reached the phloem quickly and probed for a longer time in phloem tissue than the other groups, 2) a group that reached the xylem quickly and probed for a longer time in xylem tissue than the other groups, and 3) a group where individuals did not ingest much sap. In addition, the numbers and durations of waveforms representing ingestion of xylem and phloem saps differed significantly depending on the sex of the leafhopper, indicating that the two sexes exhibit different feeding behaviors. Males had longer phloem ingestion events than did females, which indicates that males are greater phloem feeders than females. These differences are discussed, specifically in relation to hypotheses about evolution of sap feeding and phytoplasma transmission from plant to plant. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. BODY SIZE AND HAREM SIZE IN MALE RED-WINGED BLACKBIRDS: MANIPULATING SELECTION WITH SEX-SPECIFIC FEEDERS.

    Science.gov (United States)

    Rohwer, Sievert; Langston, Nancy; Gori, Dave

    1996-10-01

    We experimentally manipulated the strength of selection in the field on red-winged blackbirds (Agelaius phoeniceus) to test hypotheses about contrasting selective forces that favor either large or small males in sexually size dimorphic birds. Selander (1972) argued that sexual selection favors larger males, while survival selection eventually stabilizes male size because larger males do not survive as well as smaller males during harsh winters. Searcy (1979a) proposed instead that sexual selection may be self limiting: male size might be stabilized not by overwinter mortality, but by breeding-season sexual selection that favors smaller males. Under conditions of energetic stress, smaller males should be able to display more and thus achieve higher reproductive success. Using feeders that provisioned males or females but not both, we produced conditions that mimicked the extremes of natural conditions. We found experimental support for the hypothesis that when food is abundant, sexual selection favors larger males. But even under conditions of severe energetic stress, smaller males did not gain larger harems, as the self-limiting hypothesis predicted. Larger males were more energetically stressed than smaller males, but in ways that affected their future reproductive output rather than their current reproductive performance. Stressed males that returned had smaller wings and tails than those that did not return; among returning stressed males, relative harem sizes were inversely related to wing and tail length. Thus, male body size may be stabilized not by survival costs during the non-breeding season, nor by energetic costs during the breeding season, but by costs of future reproduction that larger males pay for their increased breeding-season effort. © 1996 The Society for the Study of Evolution.

  14. Application of a computer model to predict optimum slaughter end points for different biological types of feeder cattle.

    Science.gov (United States)

    Williams, C B; Bennett, G L

    1995-10-01

    A bioeconomic model was developed to predict slaughter end points of different genotypes of feeder cattle, where profit/rotation and profit/day were maximized. Growth, feed intake, and carcass weight and composition were simulated for 17 biological types of steers. Distribution of carcass weight and proportion in four USDA quality and five USDA yield grades were obtained from predicted carcass weights and composition. Average carcass value for each genotype was calculated from these distributions under four carcass pricing systems that varied from value determined on quality grade alone to value determined on yield grade alone. Under profitable market conditions, rotation length was shorter and carcass weights lighter when the producer's goal was maximum profit/day, compared with maximum profit/rotation. A carcass value system based on yield grade alone resulted in greater profit/rotation and in lighter and leaner carcasses than a system based on quality grade alone. High correlations ( > .97) were obtained between breed profits obtained with different sets of input/output prices and carcass price discount weight ranges. This suggests that breed rankings on the basis of breed profits may not be sensitive to changes in input/output market prices. Steers that were on a grower-stocker system had leaner carcasses, heavier optimum carcass weight, greater profits, and less variation in optimum carcass weights between genotypes than steers that were started on a high-energy finishing diet at weaning. Overall results suggest that breed choices may change with different carcass grading and value systems and postweaning production systems. This model has potential to provide decision support in marketing fed cattle.

  15. Wean-to-finish feeder space availability effects on nursery and finishing pig performance and total tract digestibility in a commercial setting when feeding dried distillers grains with solubles.

    Science.gov (United States)

    Weber, E K; Stalder, K J; Patience, J F

    2015-04-01

    The study objectives were to determine nursery phase feeder space allowance effects on pig performance when double stocked and, second, to determine feeder space allowance and dried distillers grains with solubles (DDGS) inclusion level effects on pig performance and nutrient digestibility during the growing-finishing phase. This study was performed on the same group of pigs within a commercial wean-finish system. For the nursery phase, a completely randomized design was used to compare 3 feeder space allowance treatments (2.1, 2.5, and 2.9 cm/pig). A total of 3,720 pigs were randomly allotted to same-sex pens (10 feeders/treatment) housing 62 pigs/pen. Thirty 7-hole, double-sided feeders were utilized in the study. Differing linear feeder space treatments were established by blocking off sections for the nursery and grow-finish portions of this experiment. All pigs were provided equal floor space (0.26 m2/pig). In the grow-finish phase, a total of 1,860 pigs (n = 60 pens) were utilized in a 2 × 3 factorial design with 3 feeder space allowances (4.1, 4.9, or 5.7 cm/pig) and 2 dietary DDGS treatments (30% [D30] or 60% [D60]). Fecal and diet samples were collected and analyzed to estimate apparent total tract digestibility percentage (ATTD %). In the nursery portion of the trial, there was no feeder space treatment effect on ADG, ADFI, or feed efficiency (P > 0.10) from weaning to d 56 postweaning or during any weigh period. In the grow-finish portion of the trial, feeder space allowance and DDGS inclusion level did not affect ADG, ADFI, or feed efficiency (P > 0.05) from d 57 postweaning to market. Pigs fed the D30 diet had greater HCW, percent yield, and loin depth than those on the D60 diet (P feeder space allowance did not impact pig performance during the nursery or grow-finish production phases. Inclusion of DDGS at higher levels will decrease ADFI but not ADG or efficiency when isocaloric diets are fed. The inclusion level of DDGS does impact HCW and percent

  16. Modulating effects of bioactive water Naftussya from layers Truskavets’ and Pomyarky on some metabolic and biophysic parameters at humans with dysfunction of neuro-endocrine-immune complex

    Directory of Open Access Journals (Sweden)

    Anatoliy I Gozhenko

    2016-12-01

    Full Text Available Background. Previously we have been carry out comparative investigation immediate effects of Bioactive Water Naftussya from layers Truskavets’, Pomyarky and Skhidnyts’a on neuro-endocrine-immune complex at men with its dysfunction. The aim of this study is the influence of the use of the course of Bioactive Water Naftussya from layers Truskavets’ and Pomyarky on some metabolic and biophysical parameters at similar patients. Materials and methods. The object of observation were 20 volunteers: ten women and ten men aged 33-76 years without clinical diagnose but with dysfunction of neuro-endocrine-immune complex and metabolism. In daily urine and venous blood we determined the content of electrolytes, nitrogenous metabolites and lipids, recorded conductivity of acupuncture points, rate of electronegative nuclei of buccal epithelium as well as parameters of gas discharge vizualisation (GDV. After examination volunteers within 7 days used bioactive water Naftussya (250 mL three times a day from Truskavets’ or Pomyarky layer, then repeated the tests listed. Results. Weekly use of Bioactive Water Naftussya increases in the normal level of plasma chloride and sodium, normalizes low level of bicarbonate and decreases within the normal levels of potassium and phosphate. Urinary excretion of sodium and chloride increases while excretion and concentration of uric acid decreases, as the urine concentration of phosphates. The index lithogenicity urine decreased from 112% to 103% norm standard. Initially reduced level of plasma triacylglycerides increases, while decreases in the normal level of cholesterol in low-density lipoprotein composition. Among the biophysical parameters detected increase in the normal conductivity acupuncture points Pg (ND at right side, which represent the nervous system, and left shift the ratio between the conductivity of acupuncture points MC (AVL, which represents the immune system. Increases electrokinetic index of

  17. Layering and Ordering in Electrochemical Double Layers

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yihua [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, United States; Kawaguchi, Tomoya [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, United States; Pierce, Michael S. [Rochester Institute of Technology, School of Physics and Astronomy, Rochester, New York 14623, United States; Komanicky, Vladimir [Faculty of Science, Safarik University, 041 54 Kosice, Slovakia; You, Hoydoo [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, United States

    2018-02-26

    Electrochemical double layers (EDL) form at electrified interfaces. While Gouy-Chapman model describes moderately charged EDL, formation of Stern layers was predicted for highly charged EDL. Our results provide structural evidence for a Stern layer of cations, at potentials close to hydrogen evolution in alkali fluoride and chloride electrolytes. Layering was observed by x-ray crystal truncation rods and atomic-scale recoil responses of Pt(111) surface layers. Ordering in the layer is confirmed by glancing-incidence in-plane diffraction measurements.

  18. Brief report: benchmarking human pluripotent stem cell markers during differentiation into the three germ layers unveils a striking heterogeneity: all markers are not equal.

    Science.gov (United States)

    Ramirez, Jean-Marie; Gerbal-Chaloin, Sabine; Milhavet, Ollivier; Qiang, Bai; Becker, Fabienne; Assou, Said; Lemaître, Jean-Marc; Hamamah, Samir; De Vos, John

    2011-09-01

    Pluripotent stem cells (PSC) are functionally characterized by their capacity to differentiate into all the cell types from the three germ layers. A wide range of markers, the expression of which is associated with pluripotency, has been used as surrogate evidence of PSC pluripotency, but their respective relevance is poorly documented. Here, we compared by polychromatic flow cytometry the kinetics of loss of expression of eight widely used pluripotency markers (SSEA3, SSEA4, TRA-1-60, TRA-1-81, CD24, OCT4, NANOG, and alkaline phosphatase [AP]) at days 0, 5, 7, and 9 after induction of PSC differentiation into cells representative of the three germ layers. Strikingly, each marker showed a different and specific kinetics of disappearance that was similar in all the PSC lines used and for all the induced differentiation pathways. OCT4, SSEA3, and TRA-1-60 were repeatedly the first markers to be downregulated, and their expression was completely lost at day 9. By contrast, AP activity, CD24, and NANOG proteins were still detectable at day 9. In addition, we show that differentiation markers are coexpressed with pluripotency markers before the latter begin to disappear. These results suggest that OCT4, SSEA3, and TRA-1-60 might be better to trace in vitro the emergence of pluripotent cells during reprogramming. Copyright © 2011 AlphaMed Press.

  19. Chemosensitivity and radiosensitivity testing of freshly explanted human tumour cells in vitro

    International Nuclear Information System (INIS)

    Wells, J.

    1977-10-01

    In this thesis, in vitro testing for the chemosensitivity and radiosensitivity of freshly explanted human tumour cells is described. The cells were incubated with anti-tumour drugs and either a 6-day growth test performed or a clonal growth test as a measure of survival of cell reproductive capacity. It was shown that if one aims to develop a suitable in vitro method for predicting the subsequent response of human tumour cells in situ to cytotoxic chemotherapy, the test procedure must be initiated before the explanted cells have undergone significant growth in vitro. The survival of the reproductive capacity of tumour cell explants following X-radiation was also studied. Using a 'feeder' layer technique, values for the survival curve parameter Dsub(q) were in the range 400-610 rad and the values for D 0 were in the range 120-160 rad. The shape of the X-ray survival curves did not change when cells were retested after repeated subculturing in vitro. Therefore, unlike chemosensitivity measured by the same biological end-point, radiosensitivity apparently does not change once cells have reached their maximum growth potential. (UK)

  20. Trophodynamics of inorganic pollutants in a wide-range feeder: The relevance of dietary inputs and biomagnification in the Yellow-legged gull (Larus michahellis)

    International Nuclear Information System (INIS)

    Ramos, Raül; Ramírez, Francisco; Jover, Lluís

    2013-01-01

    The suitability of sentinel species to monitor environmental pollution is often hampered by an insufficient knowledge on pollutant trophodynamics. We simultaneously evaluated the influence of individuals' trophic position (as revealed by δ 15 N values) and dietary exploitation of particular systems (using δ 13 C and δ 34 S as proxies) on inorganic pollutant concentrations measured on fledglings' feathers of a wide-range feeder, the Yellow-legged Gull (Larus michahellis), sampled at four locations throughout the Western Mediterranean. Concentrations of total Hg and Se in fledgling feathers (2.43 ± 1.30 and 1.16 ± 0.43 μg/g, respectively) were under the threshold points for deleterious effects on seabirds. On the contrary, alarming Pb concentrations were found in one colony (mean: 1.57 ± 2.46 μg/g, range: 0.16–12.13). With the exception of Pb, pollutant concentrations were positively influenced by consumption of marine resources (as suggested by the positive relationship with δ 34 S values), whereas trophic position played a minor role in determining pollutant body burdens. - Graphical abstract: Individual feeding behaviours in wide-range feeders may represent unavoidable knowledge for an appropriate understanding of contaminant acquisition, adding complexity to the study of the dynamic of contaminants throughout food chains. In this case study, pollutant body burden of Yellow-legged gull (Larus michahellis) chicks was highly influenced by dietary exposure, whereas the influence of trophic position was relatively low. Display Omitted Highlights: ► Diet origin (δ 34 S) and trophic position (δ 15 N) were tested relative to Hg, Se, and Pb levels. ► Hg and Se concentrations in gull feathers were highly influenced by δ 34 S signatures. ► Exploited habitat influenced pollutant levels to a greater extent than trophic position. ► Biomagnification processes contribute less to contamination exposure in wide-range feeders. - Pollutant body burden of a wide

  1. Belt deviation and its solution of belt weighing feeder machine%皮带称重绐料机皮带跑偏问题殁对策

    Institute of Scientific and Technical Information of China (English)

    张荣轩

    2012-01-01

    This article analyzes the reasons of common belt deviation problems during the using of belt weighing feeder machine, and combining practical work experience, proposed its solutions.%本文就皮带称重给料机在使用过程中常见的皮带跑偏问题进行了原因分析,并结合本人多年的工作实践经验,提出其相应的解决办法。

  2. Quantitative control of belt weighing feeder quick loading system%定量控制皮带称重式给料机快速装车系统

    Institute of Scientific and Technical Information of China (English)

    张荣轩

    2012-01-01

    This paper introduces a kind of belt weighing feeder quantitative control technology, which realizes the bulk material rapid loading design and widely used in coal metallurgy, chemical industry, building materials industry.%本文介绍了一种对皮带称重式给料机进行定量控制技术,实现散状物料快速装车的设计方案,广泛适用于煤炭、冶金、化工和建材等行业。

  3. Weaning age of calves fed a high milk allowance by automated feeders: effects on feed, water, and energy intake, behavioral signs of hunger, and weight gains.

    Science.gov (United States)

    de Passillé, A M; Borderas, T F; Rushen, J

    2011-03-01

    Dairy calves are increasingly fed large volumes of milk, which reduces feeding motivation and improves weight gain. However, calves often show signs of hunger and lose weight when weaned off milk due to low starter intake. We examined whether delaying the age at weaning would reduce responses to weaning. Calves were raised in groups of 9 and fed milk, starter, hay, and water with automated feeders. In each group, 3 calves were randomly assigned to 1 of 3 treatments: (1) low-milk, early-weaned: fed 6 L/d of milk and weaned at 47 d of age; (2) high-milk early-weaned: fed 12 L/d of milk and weaned at 47 d; (3) high-milk later-weaned: fed 12 L/d of milk and weaned at 89 d of age. Milk, starter, and hay intakes were recorded daily and digestible energy (DE) intake estimated. Feeder visits were recorded. Before weaning, the high-milk calves drank more milk, ate less starter and hay, but had higher DE intakes, gained more weight, and made fewer visits to the milk feeder than the low-milk, early-weaned calves. During and immediately after weaning, the high-fed, early-weaned calves ate less starter and hay, had lower DE intakes, and gained less weight than the low-milk, early-weaned calves and lost their body weight advantage 7 d after weaning. During and immediately after weaning, the high-milk, later-weaned calves ate more starter and hay and had higher DE intakes, higher weight gains, and made fewer visits to the milk feeder than the high-milk, early-weaned calves. They were still heavier than the low-milk, early-weaned calves 18 d after weaning. Delaying the age at which calves are weaned off milk reduces the drop in energy intake and behavioral signs of hunger that result from weaning. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  4. The Cost of Distribution System Upgrades to Accommodate Increasing Penetrations of Distributed Photovoltaic Systems on Real Feeders in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Horowitz, Kelsey A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Ding, Fei [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Mather, Barry A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Palmintier, Bryan S [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2018-04-05

    The increasing deployment of distributed photovoltaic systems (DPV) can impact operations at the distribution level and the transmission level of the electric grid. It is important to develop and implement forward-looking approaches for calculating distribution upgrade costs that can be used to inform system planning, market and tariff design, cost allocation, and other policymaking as penetration levels of DPV increase. Using a bottom-up approach that involves iterative hosting capacity analysis, this report calculates distribution upgrade costs as a function of DPV penetration on three real feeders - two in California and one in the Northeastern United States.

  5. The human vocal fold layers. Their delineation inside vocal fold as a background to create 3D digital and synthetic glottal model

    Czech Academy of Sciences Publication Activity Database

    Klepáček, I.; Jirák, D.; Dušková-Smrčková, Miroslava; Janoušková, Olga; Vampola, T.

    2016-01-01

    Roč. 30, č. 5 (2016), s. 529-537 ISSN 0892-1997 R&D Projects: GA ČR(CZ) GAP101/12/1306 Institutional support: RVO:61389013 Keywords : human vocal fold * vocal ligamentous complex * lamina propria Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.381, year: 2016

  6. Identification of pectenotoxins in plankton, filter feeders, and isolated cells of a Dinophysis acuminata with an atypical toxin profile, from Chile.

    Science.gov (United States)

    Blanco, Juan; Alvarez, Gonzalo; Uribe, Eduardo

    2007-04-01

    A bloom of Dinophysis acuminata produced, in autumn of 2005, a closure of the scallop harvesting in Bahía Inglesa, in the Chilean III region. Isolated cells of this Dinophysis species were shown to contain 180 pg cell(-1) of pectenotoxin 2 but neither okadaic acid nor any of its analogs or derivatives (at least at a detectable level). Examination of plankton and filter-feeder samples covering an area of ca. 350 km, from the location where the toxicity was recorded to Bahía Tongoy, showed that the unique toxin profile found in the first bloom was widespread over that part of Chile and persisted for months. The analysis were carried out by HPLC-ESI-MS using positive ionization mode, with a detection limit below 2 ng of OA mL(-1) of methanolic extract. This is the first report of the presence of pectenotoxins in the plankton of the Pacific coast of America and in the studied filter feeders. This is also the first report of a Dinophysis species containing pectenotoxins and not any toxin of the okadaic acid group.

  7. Research, Development and Demonstration of Peak Load Reduction on Distribution Feeders Using Distributed Energy Resources for the City of Fort Collins

    Energy Technology Data Exchange (ETDEWEB)

    Sumner, Dennis [City of Fort Collins Utilities, CO (United States); Vosburg, Tom [City of Fort Collins Utilities, CO (United States); Brunner, Steve [Brendle Group, Fort Collins, CO (United States); Gates, Judy [Woodward, Inc., Fort Collins, CO (United States); Howard, Nathan [Spirae, Inc., Fort Collins, CO (United States); Merton, Andrew [Spirae, Inc., Fort Collins, CO (United States); Wright, Don [Spirae, Inc., Fort Collins, CO (United States); Birlingmair, Doug [Spirae, Inc., Fort Collins, CO (United States)

    2015-10-01

    This project titled “Research, Development and Demonstration of Peak Load Reduction on Distribution Feeders Using Distributed Energy Resources for the City of Fort Collins” evolved in response to the Department of Energy’s (DOE) Funding Opportunity Announcement (FOA) Number DE-PS26-07NT43119. Also referred to as the Fort Collins Renewable and Distributed System Integration (RDSI) Project, the effort was undertaken by a diverse group of local government, higher education and business organizations; and was driven by three overarching goals: I. Fulfill the requirements of the DOE FOA’s Area of Interest 2: Renewable and Distributed System Integration; most notably, to demonstrate the ability to reduce electric system distribution feeder peak load by 15% or more through the coordinated use of Distributed Energy Resources (DER). II. Advance the expertise, technologies and infrastructure necessary to support the long term vision of the Fort Collins Zero Energy District (FortZED) and move towards creating a zero energy district in the Fort Collins “Old Town” area. III. Further the goals of the City of Fort Collins Energy Policy, including the development of a Smart Grid-enabled distribution system in Fort Collins, expanded use of renewable energy, increased energy conservation, and peak load reduction. Through the collaborative efforts of the partner organizations, the Fort Collins RDSI project was successful in achieving all three of these goals. This report is organized into two distinct sections corresponding to the two phases of the project: • Part 1: Feeder Peak Load Reduction and the FortZED Initiative. • Part 2: Forming and Operating Utility Microgrids and Managing Load and Production Variability The original project scope addressed the Part 1 feeder peak load reduction. That work took place from 2009 through 2011 and was largely complete when the project scope was amended to include a demonstration of microgrid operations. While leveraging the

  8. Epigenetic stability, adaptability, and reversibility in human embryonic stem cells

    OpenAIRE

    Tompkins, Joshua D.; Hall, Christine; Chen, Vincent Chang-yi; Li, Arthur Xuejun; Wu, Xiwei; Hsu, David; Couture, Larry A.; Riggs, Arthur D.

    2012-01-01

    The stability of human embryonic stem cells (hESCs) is of critical importance for both experimental and clinical applications. We find that as an initial response to altered culture conditions, hESCs change their transcription profile for hundreds of genes and their DNA methylation profiles for several genes outside the core pluripotency network. After adaption to conditions of feeder-free defined and/or xeno-free culture systems, expression and DNA methylation profiles are quite stable for a...

  9. The comparison of two methods to obtain human oral keratinocytes in primary culture; Comparacao de dois metodos de obtencao celular para cultura primaria de queratinocitos bucais humanos

    Energy Technology Data Exchange (ETDEWEB)

    Klingbeil, Maria Fatima Guarizo

    2006-07-01

    The therapeutic procedures frequently used in oral treatments for the pathological diseases are surgical, resulting in failures of the mucosal continuity.The possibility to obtain transplantable oral epithelia from an in vitro cell culture opens new utilization perspectives not only to where it comes from, but also as a reconstructive material for other parts of the human body, such as: urethra, epithelia corneo-limbal, cornea, ocular surface. Many researchers still use controversial methods for obtaining cells. It was therefore evaluated and compared the efficiency in both methods: enzymatic and direct explant to obtain oral keratinocytes from human oral mucosa. Fragments of intra oral epithelial tissues from healthy human subjects, undergoing dental surgeries, were donated to the research project. The keratinocytes were cultivated over a feeder-layer from a previously irradiated 3T3 Swiss albino fibroblasts. In this study it was compared the time needed in the cell obtention, the best cell amount between both methods, the life-span, the cell capacity to form an in vitro epithelia and its morphologic structure. The results in the assessment of both methods have shown the possibility to obtain keratinocytes from a small oral fragment, but at the same time we may verify the advantages and peculiar restrictions for each one of both analyzed methods. (author)

  10. Incorporation of human factors into ship collision risk models focusing on human centred design aspects

    International Nuclear Information System (INIS)

    Sotiralis, P.; Ventikos, N.P.; Hamann, R.; Golyshev, P.; Teixeira, A.P.

    2016-01-01

    This paper presents an approach that more adequately incorporates human factor considerations into quantitative risk analysis of ship operation. The focus is on the collision accident category, which is one of the main risk contributors in ship operation. The approach is based on the development of a Bayesian Network (BN) model that integrates elements from the Technique for Retrospective and Predictive Analysis of Cognitive Errors (TRACEr) and focuses on the calculation of the collision accident probability due to human error. The model takes into account the human performance in normal, abnormal and critical operational conditions and implements specific tasks derived from the analysis of the task errors leading to the collision accident category. A sensitivity analysis is performed to identify the most important contributors to human performance and ship collision. Finally, the model developed is applied to assess the collision risk of a feeder operating in Dover strait using the collision probability estimated by the developed BN model and an Event tree model for calculation of human, economic and environmental risks. - Highlights: • A collision risk model for the incorporation of human factors into quantitative risk analysis is proposed. • The model takes into account the human performance in different operational conditions leading to the collision. • The most important contributors to human performance and ship collision are identified. • The model developed is applied to assess the collision risk of a feeder operating in Dover strait.

  11. Estimation of boswellic acids from market formulations of Boswellia serrata extract and 11-keto beta-boswellic acid in human plasma by high-performance thin-layer chromatography.

    Science.gov (United States)

    Shah, Shailesh A; Rathod, Ishwarsinh S; Suhagia, Bhanubhai N; Patel, Dharmesh A; Parmar, Vijay K; Shah, Bharat K; Vaishnavi, Vikas M

    2007-04-01

    A rapid and sensitive high-performance thin-layer chromatographic (HPTLC) method was developed and validated for the quantitative estimation of boswellic acids in formulation containing Boswellia serrata extract (BSE) and 11-keto beta-boswellic acid in human plasma. Simple extraction method was used for isolation of boswellic acid from formulation sample and acidified plasma sample. The isolated samples were chromatographed on silica gel 60F(254)-TLC plates, developed using ternary-solvent system (hexane-chloroform-methanol, 5:5:0.5, v/v) and scanned at 260 nm. The linearity range for 11-KBA spiked in 1 ml of plasma was 29.15-145.75 ng with average recovery of 91.66%. The limit of detection and limit of quantification for 11-KBA in human plasma were found to be 8.75 ng/ml and 29.15 ng/ml. The developed method was successfully applied for the assay of market formulations containing BSE and to determine plasma level of 11-keto beta-boswellic acid in a clinical pilot study.

  12. Tunical Outer Layer Plays an Essential Role in Penile Veno-occlusive Mechanism Evidenced from Electrocautery Effects to the Corpora Cavernosa in Defrosted Human Cadavers.

    Science.gov (United States)

    Hsieh, Cheng-Hsing; Huang, Yi-Ping; Tsai, Mang-Hung; Chen, Heng-Shen; Huang, Po-Cheng; Lin, Chung-Wu; Hsu, Geng-Long

    2015-12-01

    To determine the exact anatomical structure for establishing penile veno-occlusive function, we sought to conduct a hemodynamic study on defrosted human cadavers. Thirteen penises were used for this experiment, and 11 intact penises were allocated into the electrocautery group (EG, n = 6) and the ligation group (LG, n = 5). A circumcision was made on the penis to access the veins. Two #19 scalp needles were fixed in the 3 and 9 o'clock positions in the distal penis for colloid infusion and intracavernous pressure (ICP) monitoring, respectively. For the EG, the deep dorsal vein and cavernosal vein trunks were freed for 3-5 cm where at least 3 emissary veins were identified via opening Buck's fascia; these veins underwent electrocautery at 45 watts, while the ICP was maintained at 0, 50, 75, 100, 125, and 150 mmHg, respectively. For control, venous ligation was made but at the ICP of 150 mmHg. A tissue block including the emissary vein was then obtained for histological analysis. Except all in the EG and those whose ICP exceed 125 mmHg in the EG, the sinusoids of the corpora cavernosa sustained varied fulgurated fibrosis in every specimen and the severity appeared reversely commensurate with the ICP regarding sinusoidal clumping and darkish bands (P electrocautery damage to intracavernous sinusoids once the ICP reached a level corresponding to a rigid erection. The outer tunica plays an essential role in fulfilling the veno-occlusive mechanism. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  13. Higher-Density Culture in Human Embryonic Stem Cells Results in DNA Damage and Genome Instability

    Directory of Open Access Journals (Sweden)

    Kurt Jacobs

    2016-03-01

    Full Text Available Human embryonic stem cells (hESC show great promise for clinical and research applications, but their well-known proneness to genomic instability hampers the development to their full potential. Here, we demonstrate that medium acidification linked to culture density is the main cause of DNA damage and genomic alterations in hESC grown on feeder layers, and this even in the short time span of a single passage. In line with this, we show that increasing the frequency of the medium refreshments minimizes the levels of DNA damage and genetic instability. Also, we show that cells cultured on laminin-521 do not present this increase in DNA damage when grown at high density, although the (long-term impact on their genomic stability remains to be elucidated. Our results explain the high levels of genome instability observed over the years by many laboratories worldwide, and show that the development of optimal culture conditions is key to solving this problem.

  14. Comparative bioaccumulation of trace metals using six filter feeder organisms in a coastal lagoon ecosystem (of the central-east Gulf of California).

    Science.gov (United States)

    Jara-Marini, M E; Tapia-Alcaraz, J N; Dumer-Gutiérrez, J A; García-Rico, L; García-Hernández, J; Páez-Osuna, F

    2013-02-01

    The Tobari Lagoon, located in the central-east coast of the Gulf of California, receives effluents from the Yaqui Valley, one of the most extensive agricultural areas of México. The Tobari Lagoon also receives effluents from nearby shrimp farms and untreated municipal sewage. Surface sediment samples and six different species of filter feeders (Crassostrea corteziensis, Crassostrea gigas, Chione gnidia, Anadara tuberculosa, Chione fluctifraga, and Fistulobalanus dentivarians) were collected during the dry and the rainy seasons and analyzed to determine concentrations of cadmium (Cd), copper (Cu), mercury (Hg), lead (Pb), and zinc (Zn). Seasonal variations in metal concentrations in sediment were evident, especially for Cd, Cu, Hg, and Zn. The total and bioavailable concentrations of the five metals are not elevated in comparison to other areas around the world. The percentages of bioavailable respect to total concentrations of the metals varied from 0.6 % in Hg to 50.2 % for Cu. In the organisms, Hg showed the lowest concentrations (ranged from 0.22 to 0.65 μg/g) while Zn showed the highest (ranged from 36.6 to 1,702 μg/g). Linear correlations between the levels of Cu, Pb, and Zn in the soft tissues of C. fluctifraga and C. gnidia, and A. tuberculosa and C. gnidia were found. Seasonal and interspecies variations in the metal levels in filter feeders were found; F. dentivarians, C. corteziensis, and C. gigas exhibited the highest levels, could be used as biomonitors of metals contamination in this area.

  15. 47 CFR 25.250 - Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. 25.250 Section 25.250 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Technical Standards § 25...

  16. Practice on Protection and Improvement of Withstand Voltage Weighing Belt Coal Feeder%耐压称重式皮带给煤机保护改进实践

    Institute of Scientific and Technical Information of China (English)

    王良

    2016-01-01

    This paper introduces the traits of withstand voltage weighing belt coal feeder. According to the modification and practice of parameters of the frequency converter, when there is a malfunction, the automatic recovery of the frequency converter of coal feeder can be achieved. The reliability of the coal feeder ’s operation will be improved, and the effects of the accident power supply perturbation on the coal feeder can be eliminated. Eventually, the safety and stability of the boilers can be guaranteed.%文章介绍了耐压称重式皮带给煤机的特性,通过对变频器参数修改实践,实现给煤机变频器故障保护自动恢复,提高给煤机运行的可靠性,消除电源意外扰动对给煤机的影响,保障锅炉安全持续稳定运行。

  17. Oxidative stress by layered double hydroxide nanoparticles via an SFK-JNK and p38-NF-κB signaling pathway mediates induction of interleukin-6 and interleukin-8 in human lung epithelial cells

    Directory of Open Access Journals (Sweden)

    Choi SJ

    2015-04-01

    Full Text Available Soo-Jin Choi, Hee-Jeong Paek, Jin YuDepartment of Food Science and Technology, Seoul Women’s University, Seoul, Republic of KoreaAbstract: Anionic nanoclays are layered double hydroxide nanoparticles (LDH-NPs that have been shown to exhibit toxicity by inducing reactive oxidative species and a proinflammatory mediator in human lung epithelial A549 cells. However, the molecular mechanism responsible for this LDH-NP-induced toxicity and the relationship between oxidative stress and inflammatory events remains unclear. In this study, we focused on intracellular signaling pathways and transcription factors induced in response to oxidative stress caused by exposure to LDH-NPs in A549 cells. Mitogen-activated protein kinase (MAPK cascades, such as extracellular signal-regulated kinase, c-Jun-N-terminal kinase (JNK, and p38, were investigated as potential signaling mechanisms responsible for regulation of oxidative stress and cytokine release. Src family kinases (SFKs, which are known to mediate activation of MAPK, together with redox-sensitive transcription factors, including nuclear factor kappa B and nuclear factor-erythroid 2-related factor-2, were also investigated as downstream events of MAPK signaling. The results obtained suggest that LDH-NP exposure causes oxidative stress, leading to expression of antioxidant enzymes, such as catalase, glucose reductase, superoxide dismutase, and heme oxygenase-1, via a SFK-JNK and p38-nuclear factor kappa B signaling pathway. Further, activation of this signaling was also found to regulate release of inflammatory cytokines, including interleukin-6 and interleukin-8, demonstrating the inflammatory potential of LDH-NP.Keywords: layered double hydroxide, mitogen-activated protein kinases, Src family kinases, nuclear factor kappa B, oxidative stress, inflammatory cytokine

  18. VSWI Wetlands Advisory Layer

    Data.gov (United States)

    Vermont Center for Geographic Information — This dataset represents the DEC Wetlands Program's Advisory layer. This layer makes the most up-to-date, non-jurisdictional, wetlands mapping avaiable to the public...

  19. Cloning of a novel cell type from human fetal liver expressing cytoplasmic CD3 delta and epsilon but not membrane CD3

    NARCIS (Netherlands)

    Hori, T.; de Waal Malefyt, R.; Duncan, B. W.; Harrison, M. R.; Roncarolo, M. G.; Spits, H.

    1991-01-01

    Seventeen-week human fetal liver cells cultured with a feeder cell mixture of irradiated PBL, irradiated JY cells (an EBV-transformed B cell line) and PHA contained a subpopulation of CD3- cells in addition to a major population of T cells with the mature phenotype. After 12 days in culture, CD3-

  20. Layer-by-layer cell membrane assembly

    Science.gov (United States)

    Matosevic, Sandro; Paegel, Brian M.

    2013-11-01

    Eukaryotic subcellular membrane systems, such as the nuclear envelope or endoplasmic reticulum, present a rich array of architecturally and compositionally complex supramolecular targets that are as yet inaccessible. Here we describe layer-by-layer phospholipid membrane assembly on microfluidic droplets, a route to structures with defined compositional asymmetry and lamellarity. Starting with phospholipid-stabilized water-in-oil droplets trapped in a static droplet array, lipid monolayer deposition proceeds as oil/water-phase boundaries pass over the droplets. Unilamellar vesicles assembled layer-by-layer support functional insertion both of purified and of in situ expressed membrane proteins. Synthesis and chemical probing of asymmetric unilamellar and double-bilayer vesicles demonstrate the programmability of both membrane lamellarity and lipid-leaflet composition during assembly. The immobilized vesicle arrays are a pragmatic experimental platform for biophysical studies of membranes and their associated proteins, particularly complexes that assemble and function in multilamellar contexts in vivo.

  1. Method for manufacturing carrier containing e.g. proteins for human during oral drug delivery operation for food and drug administration application in pharmaceutical industry, involves providing active ingredient to core layer

    DEFF Research Database (Denmark)

    2015-01-01

    NOVELTY - The method involves preparing a multi-layered film comprising a core layer and a barrier layer, where the core layer comprises active ingredient. The multi-layered film is subjected to a hot embossing step using an embossing stamp including protrusions that allows for generation...... delivery operation for a food and drug administration (FDA) application in a pharmaceutical industry. ADVANTAGE - The method enables allowing an individual micro-structure stuck in an embossing stamp to be demolded under the conditions such that demolding operation is done by treating elastically...

  2. Double layers in space

    International Nuclear Information System (INIS)

    Carlqvist, P.

    1982-07-01

    For more than a decade it has been realised that electrostatic double layers are likely to occur in space. We briefly discuss the theoretical background of such double layers. Most of the paper is devoted to an account of the observational evidence for double layers in the ionosphere and magnetosphere of the Earth. Several different experiments are reviewed including rocket and satellite measurements and ground based observations. It is concluded that the observational evidence for double layers in space is very strong. The experimental results indicate that double layers with widely different properties may exist in space. (Author)

  3. Double layers in space

    International Nuclear Information System (INIS)

    Carlqvist, P.

    1982-01-01

    For more than a decade it has been realised that electrostatic double layers are likely to occur in space. The author briefly discusses the theoretical background of such double layers. Most of the paper is devoted to an account of the observational evidence for double layers in the ionosphere and magnetosphere of the Earth. Several different experiments are reviewed including rocket and satellite measurements and ground based observations. It is concluded that the observational evidence for double layers in space is very strong. The experimental results indicate that double layers with widely different properties may exist in space. (Auth.)

  4. Gene expression studies on human keratinocytes transduced with human growth hormone gene for a possible utilization in gene therapy; Estudos da expressao genica mediante utilizacao de queratinocitos humanos normais transduzidos com o gene do hormonio de crscimento humano. Possivel utilizacao em terapia genica

    Energy Technology Data Exchange (ETDEWEB)

    Mathor, Monica Beatriz

    1994-12-31

    Taking advantage of the recent progress in the DNA-recombinant techniques and of the potentiality of normal human keratinocytes primary culture to reconstitute the epidermis, it was decided to genetically transform these keratinocytes to produce human growth hormone under controllable conditions that would be used in gene therapy at this hormone deficient patients. The first step to achieve this goal was to standardize infection of keratinocytes with retrovirus producer cells containing a construct which included the gene of bacterial b-galactosidase. The best result was obtained cultivating the keratinocytes for 3 days in a 2:1 mixture of retrovirus producer cells and 3T3-J2 fibroblasts irradiated with 60 Gy, and splitting these infected keratinocytes on 3T3-J2 fibroblasts feeder layer. Another preliminary experiment was to infect normal human keratinocytes with interleukin-6 gene (hIL-6) that, in pathologic conditions, could be reproduced by keratinocytes and secreted to the blood stream. Thus, we verify that infected keratinocytes secrete an average amount of 500 ng/10{sup 6} cell/day of cytokin during the in vitro life time, that certify the stable character of the injection. These keratinocytes, when grafted in mice, secrete hIL-6 to the blood stream reaching levels of 40 pg/ml of serum. After these preliminary experiments, we construct a retroviral vector with the human growth hormone gene (h GH) driven by human metallothionein promoter (h PMT), designated DChPMTGH. Normal human keratinocytes were infected with DChPMTGH producer cells, following previously standardized protocol, obtaining infected keratinocytes secreting to the culture media 340 ng h GH/10{sup 6} cell/day without promoter activation. This is the highest level of h GH secreted in human keratinocytes primary culture described in literature. The h GH value increases approximately 10 times after activation with 100 {mu}M Zn{sup +2} for 8-12 hours. (author). 158 refs., 42 figs., 6 tabs.

  5. Analisis Koordinasi Over Current Relay Dan Recloser Di Sistem Proteksi Feeder Gardu Induk Semen Nusantara (Snt 2) Cilacap

    OpenAIRE

    Hariyanto, Dwi Puji; Tiyono, -; Sutarno, -

    2009-01-01

    The main aim of protection system is used to protect safety of human cause by electrics current and to protect equipment from the fault. The fault can cause over current which has big value and endangerous the equipment. Besides the fault can also cause supply of energy to consumer is disturbed. The fault can be permanently or temporary. Coordination of protection system between OCR and recloser is needed to anticipate the fault.To create good coordination in protection system, the threshold ...

  6. A Simple and Robust Method for Culturing Human-Induced Pluripotent Stem Cells in an Undifferentiated State Using Botulinum Hemagglutinin.

    Science.gov (United States)

    Kim, Mee-Hae; Matsubara, Yoshifumi; Fujinaga, Yukako; Kino-Oka, Masahiro

    2018-02-01

    Clinical and industrial applications of human-induced pluripotent stem cells (hiPSCs) is hindered by the lack of robust culture strategies capable of sustaining a culture in an undifferentiated state. Here, a simple and robust hiPSC-culture-propagation strategy incorporating botulinum hemagglutinin (HA)-mediated selective removal of cells deviating from an undifferentiated state is developed. After HA treatment, cell-cell adhesion is disrupted, and deviated cells detached from the central region of the colony to subsequently form tight monolayer colonies following prolonged incubation. The authors find that the temporal and dose-dependent activity of HA regulated deviated-cell removal and recoverability after disruption of cell-cell adhesion in hiPSC colonies. The effects of HA are confirmed under all culture conditions examined, regardless of hiPSC line and feeder-dependent or -free culture conditions. After routine application of our HA-treatment paradigm for serial passages, hiPSCs maintains expression of pluripotent markers and readily forms embryoid bodies expressing markers for all three germ-cell layers. This method enables highly efficient culturing of hiPSCs and use of entire undifferentiated portions without having to pick deviated cells manually. This simple and readily reproducible culture strategy is a potentially useful tool for improving the robust and scalable maintenance of undifferentiated hiPSC cultures. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Effects of mechanical stimulation on the reprogramming of somatic cells into human-induced pluripotent stem cells.

    Science.gov (United States)

    Kim, Young Mi; Kang, Yun Gyeong; Park, So Hee; Han, Myung-Kwan; Kim, Jae Ho; Shin, Ji Won; Shin, Jung-Woog

    2017-06-08

    Mechanical stimuli play important roles in the proliferation and differentiation of adult stem cells. However, few studies on their effects on induced pluripotent stem cells (iPSCs) have been published. Human dermal fibroblasts were seeded onto flexible membrane-bottom plates, and infected with retrovirus expressing the four reprogramming factors OCT4, SOX2, KLF, and c-MYC (OSKM). The cells were subjected to equiaxial stretching (3% or 8% for 2, 4, or 7 days) and seeded on feeder cells (STO). The reprogramming into iPSCs was evaluated by the expression of pluripotent markers, in vitro differentiation into three germ layers, and teratoma formation. Equiaxial stretching enhanced reprogramming efficiency without affecting the viral transduction rate. iPSCs induced by transduction of four reprogramming factors and application of equiaxial stretching had characteristics typical of iPSCs in terms of pluripotency and differentiation potentials. This is the first study to show that mechanical stimuli can increase reprogramming efficiency. However, it did not enhance the infection rate, indicating that mechanical stimuli, defined as stretching in this study, have positive effects on reprogramming rather than on infection. Additional studies should evaluate the mechanism underlying the modulation of reprogramming of somatic cells into iPSCs.

  8. Layered Graph Drawing for Visualizing Evaluation Structures.

    Science.gov (United States)

    Onoue, Yosuke; Kukimoto, Nobuyuki; Sakamoto, Naohisa; Misue, Kazuo; Koyamada, Koji

    2017-01-01

    An evaluation structure is a hierarchical structure of human cognition extracted from interviews based on the evaluation grid method. An evaluation structure can be defined as a directed acyclic graph (DAG). The authors propose a layer-assignment method that is part of the Sugiyama framework, a popular method for drawing DAGs, to satisfy the requirements for drawing evaluation structures. Their evaluations demonstrate that the layered graph drawing produced by the proposed layer-assignment method is preferred by users and aids in the understanding of evaluation structures.

  9. Generation of Hepatocyte-like Cells from Human Induced Pluripotent Stem (iPS) Cells By Co-culturing Embryoid Body Cells with Liver Non-parenchymal Cell Line TWNT-1

    International Nuclear Information System (INIS)

    Javed, M. S.; Yaqoob, N.; Iwamuro, M.; Kobayashi, N.; Fujiwara, T.

    2014-01-01

    Objective: To generate a homogeneous population of patient-specific hepatocyte-like cells (HLCs) from human iPS cells those show the morphologic and phenotypic properties of primary human hepatocytes. Study Design: An experimental study. Place and Duration of Study: Department of Surgery, Okayama University, Graduate School of Medicine, Japan, from April to December 2011. Methodology: Human iPS cells were generated and maintained on ES qualified matrigel coated plates supplemented with mTeSR medium or alternatively on mitotically inactivated MEF feeder layer in DMEM/F12 medium containing 20% KOSR, 4ng/ml bFGF-2, 1 x 10-4 M 2-mercaptoethanol, 1 mmol/L NEAA, 2mM L-glutamine and 1% penicillin-streptomycin. iPS cells were differentiated to HLCs by sequential culture using a four step differentiation protocol: (I) Generation of embryoid bodies (EBs) in suspension culture; (II) Induction of definitive endoderm (DE) from 2 days old EBs by growth in human activin-A (100 ng/ml) and basic fibroblasts growth factor (bFGF2) (100 ng/ml) on matrigel coated plates; (III) Induction of hepatic progenitors by co-culture with non-parenchymal human hepatic stellate cell line (TWNT-1); and (IV) Maturation by culture in dexamethasone. Characterization was performed by RT-PCR and functional assays. Results: The generated HLCs showed microscopically morphological phenotype of human hepatocytes, expressed liver specific genes (ASGPR, Albumin, AFP, Sox17, Fox A2), secreted human liver-specific proteins such as albumin, synthesized urea and metabolized ammonia. Conclusion: Functional HLCs were generated from human iPS cells, which could be used for autologus hepatocyte transplantation for liver failure and as in vitro model for determining the metabolic and toxicological properties of drug compounds. (author)

  10. Multi-layers castings

    Directory of Open Access Journals (Sweden)

    J. Szajnar

    2010-01-01

    Full Text Available In paper is presented the possibility of making of multi-layers cast steel castings in result of connection of casting and welding coating technologies. First layer was composite surface layer on the basis of Fe-Cr-C alloy, which was put directly in founding process of cast carbon steel 200–450 with use of preparation of mould cavity method. Second layer were padding welds, which were put with use of TIG – Tungsten Inert Gas surfacing by welding technology with filler on Ni matrix, Ni and Co matrix with wolfram carbides WC and on the basis on Fe-Cr-C alloy, which has the same chemical composition with alloy, which was used for making of composite surface layer. Usability for industrial applications of surface layers of castings were estimated by criterion of hardness and abrasive wear resistance of type metal-mineral.

  11. Boundary-Layer & health

    Science.gov (United States)

    Costigliola, V.

    2010-09-01

    It has long been known that specific atmospheric processes, such as weather and longer-term climatic fluctuations, affect human health. The biometeorological literature refers to this relationship as meteorotropism, defined as a change in an organism that is correlated with a change in atmospheric conditions. Plenty of (patho)physiological functions are affected by those conditions - like the respiratory diseases - and currently it is difficult to put any limits for pathologies developed in reply. Nowadays the importance of atmospheric boundary layer and health is increasingly recognised. A number of epidemiologic studies have reported associations between ambient concentrations of air pollution, specifically particulate pollution, and adverse health effects, even at the relatively low concentrations of pollution found. Since 1995 there have been over twenty-one studies from four continents that have explicitly examined the association between ambient air pollutant mixes and daily mortality. Statistically significant and positive associations have been reported in data from various locations around the world, all with varying air pollutant concentrations, weather conditions, population characteristics and public health policies. Particular role has been given to atmospheric boundary layer processes, the impact of which for specific patient-cohort is, however, not well understood till now. Assessing and monitoring air quality are thus fundamental to improve Europe's welfare. One of current projects run by the "European Medical Association" - PASODOBLE will develop and demonstrate user-driven downstream information services for the regional and local air quality sectors by combining space-based and in-situ data with models in 4 thematic service lines: - Health community support for hospitals, pharmacies, doctors and people at risk - Public information for regions, cities, tourist industry and sporting event organizers - Compliance monitoring support on particulate

  12. Effects of temperament and acclimation to handling on feedlot performance of Bos taurus feeder cattle originated from a rangeland-based cow-calf system.

    Science.gov (United States)

    Francisco, C L; Cooke, R F; Marques, R S; Mills, R R; Bohnert, D W

    2012-12-01

    Two experiments evaluated the effects of temperament and acclimation to handling on performance of Angus × Hereford feeder cattle reared in extensive rangeland systems until weaning. In Exp. 1, 200 calves (n = 97 for yr 1; n = 103 for yr 2) were evaluated for temperament at weaning (average age ± SE = 152 ± 1 d) by chute score and exit velocity. Chute score was assessed on a 5-point scale according to behavior during chute restraining. Exit score was calculated by dividing exit velocity into quintiles and assigning calves a score from 1 (slowest) to 5 (fastest). A temperament score was calculated for each calf by averaging chute and exit scores. Calf temperament was classified according to temperament score as adequate (≤3) or excitable (>3). After weaning, calves were assigned to a 40-d preconditioning followed by growing (139 d) and finishing (117 d) phases until slaughter. Weaning BW was decreased (P = 0.04) in excitable calves compared with adequate calves. No differences were detected (P ≥ 0.21) for ADG during preconditioning, growing, and finishing phases; hence, excitable calves tended (P = 0.09) to have decreased HCW compared with adequate calves. In Exp. 2, 60 steers (initial age ± SE = 198 ± 2 d) were weighed and evaluated for temperament score 35 d after weaning (d -29). On d -28, steers were ranked by these variables and assigned to receive an acclimation treatment or not (control). Acclimated steers were processed through a handling facility twice weekly for 4 wk (d -28 to -1) whereas control steers remained undisturbed on pasture. On d 0, all steers were transported for 24 h and returned to the research facility (d 1). On arrival, steers were ranked by BW within treatment and randomly assigned to 20 feedlot pens for a 28-d feedlot receiving period. Acclimated steers had decreased temperament score and plasma cortisol compared with controls on d 0 (P = 0.02). During feedlot receiving, acclimated steers had decreased ADG (P < 0.01) and G:F (P

  13. A double layer review

    International Nuclear Information System (INIS)

    Block, L.P.

    1977-06-01

    A review of the main results on electrostatic double layers (sometimes called space charge layers or sheaths) obtained from theory, and laboratory and space experiments up to the spring of 1977 is given. By means of barium jets and satellite probes, double layers have now been found at the altitudes, earlier predicted theoretically. The general potential distribution above the auroral zone, suggested by inverted V-events and electric field reversals, is corroborated. (author)

  14. Two layer powder pressing

    International Nuclear Information System (INIS)

    Schreiner, H.

    1979-01-01

    First, significance and advantages of sintered materials consisting of two layers are pointed out. By means of the two layer powder pressing technique metal powders are formed resulting in compacts with high accuracy of shape and mass. Attributes of basic powders, different filling methods and pressing techniques are discussed. The described technique is supposed to find further applications in the field of two layer compacts in the near future

  15. Economical Atomic Layer Deposition

    Science.gov (United States)

    Wyman, Richard; Davis, Robert; Linford, Matthew

    2010-10-01

    Atomic Layer Deposition is a self limiting deposition process that can produce films at a user specified height. At BYU we have designed a low cost and automated atomic layer deposition system. We have used the system to deposit silicon dioxide at room temperature using silicon tetrachloride and tetramethyl orthosilicate. Basics of atomic layer deposition, the system set up, automation techniques and our system's characterization are discussed.

  16. Stable Boundary Layer Issues

    OpenAIRE

    Steeneveld, G.J.

    2012-01-01

    Understanding and prediction of the stable atmospheric boundary layer is a challenging task. Many physical processes are relevant in the stable boundary layer, i.e. turbulence, radiation, land surface coupling, orographic turbulent and gravity wave drag, and land surface heterogeneity. The development of robust stable boundary layer parameterizations for use in NWP and climate models is hampered by the multiplicity of processes and their unknown interactions. As a result, these models suffer ...

  17. Layered plasma polymer composite membranes

    Science.gov (United States)

    Babcock, Walter C.

    1994-01-01

    Layered plasma polymer composite fluid separation membranes are disclosed, which comprise alternating selective and permeable layers for a total of at least 2n layers, where n is .gtoreq.2 and is the number of selective layers.

  18. Formation of double layers

    International Nuclear Information System (INIS)

    Leung, P.; Wong, A.Y.; Quon, B.H.

    1981-01-01

    Experiments on both stationary and propagating double layers and a related analytical model are described. Stationary double layers were produced in a multiple plasma device, in which an electron drift current was present. An investigation of the plasma parameters for the stable double layer condition is described. The particle distribution in the stable double layer establishes a potential profile, which creates electron and ion beams that excite plasma instabilities. The measured characteristics of the instabilities are consistent with the existence of the double layer. Propagating double layers are formed when the initial electron drift current is large. Ths slopes of the transition region increase as they propagate. A physical model for the formation of a double layer in the experimental device is described. This model explains the formation of the low potential region on the basis of the space charge. This space charge is created by the electron drift current. The model also accounts for the role of ions in double layer formation and explains the formation of moving double layers. (Auth.)

  19. Electroless atomic layer deposition

    Science.gov (United States)

    Robinson, David Bruce; Cappillino, Patrick J.; Sheridan, Leah B.; Stickney, John L.; Benson, David M.

    2017-10-31

    A method of electroless atomic layer deposition is described. The method electrolessly generates a layer of sacrificial material on a surface of a first material. The method adds doses of a solution of a second material to the substrate. The method performs a galvanic exchange reaction to oxidize away the layer of the sacrificial material and deposit a layer of the second material on the surface of the first material. The method can be repeated for a plurality of iterations in order to deposit a desired thickness of the second material on the surface of the first material.

  20. Correlation between dried blood spot thin layer chromatography and plasma high performance liquid chromatography of leucine/isoleucine levels among Filipino patients with maple syrup urine disease (MSUD) seen at the Institute of Human Genetics, National Institutes of Health

    International Nuclear Information System (INIS)

    Yaplito-Lee, Joy; Chiong, Mary Anne D.; Rana, Michelle D.; Rama, Kahlil Izza D.; David-Padilla, Carmencita; Cavan, Barbra Charina; Cordero, Cynthia P.

    2008-01-01

    Management of patients with maple syrup urine disease (MSUD) includes a low protein diet, supplemented with special formulas and constant monitoring of branched chain amino acids (BCAA). The gold standard for monitoring BCAA is plasma amino acid analysis using high performance liquid chromatography (HPLC). In a developing country like the Philippines, however, the cost of this test is prohibitive to the majority of the patients. In our center, dried blood spot leucine/isoleucine (leu/ile) levels analysed by thin layer chromatography (TLC) is often used to diagnose and monitor these patients. This study was done to determine the correlation of leu/ile levels using the two methods (TLC and HPLC). A total of 46 MSUD patients were referred to the Biochemical Genetics Laboratory of the Institute of Human Genetics (IHG) from July 2001 to January 2004. Thirty five samples were obtained from 18 of these patients (some patients were seen at IHG more than once), and paired determinations of plasma amino acid using TLC and HPLC were made. The remaining samples were either hemolyzed or were not analyzed. The correlation coefficient [rho denoted as ρ] was estimated at a 95% confidence level using the Fisher's Z transformation. Of the 18 patients, 12 were males. The youngest was 1 day old and the oldest was 5 years old. The majority had the classical type of MSUD and dietary protein was restricted to between 0.6 gram/kg/day to 1 gram/kg/day of natural protein. Using the first pairs of observation for these 18 patients, the correlation coefficient was 0.76 (95% C1:0.462 to 0.907). This suggest a strong correlation between the two methods. It is recommended that further studies be done to determine the potential of the dried blood spot leu/ile level by TLC as an alternative method that can be used in the diagnosis and monitoring of MSUD patients especially in a developing country. (Author)

  1. Feeder and post Deccan Trap dyke activities in the northern slope of the Satpura Mountain: Evidence from new 40Ar-39Ar ages

    Directory of Open Access Journals (Sweden)

    J.P. Shrivastava

    2017-05-01

    Full Text Available We present new 40Ar-39Ar plagioclase crystallization ages from the dykes exposed at the northern slope of the Satpura Mountain range near Betul-Jabalpur-Pachmarhi area, ∼800 km NE of the Western Ghats escarpment. Among the two plateau ages, the first age of 66.56 ± 0.42 Ma from a dyke near Mohpani village represents its crystallization age which is either slightly older or contemporaneous with the nearby Mandla lava flows (63–65 Ma. We suggest that the Mohpani dyke might be one of the feeders for the surrounding lava flows as these lavas are significantly younger than the majority of the main Deccan lavas of the Western Ghats (66.38–65.54 Ma. The second age of 56.95 ± 1.08 Ma comes from a younger dyke near Olini village which cuts across the lava flows of the area. The age correlates well with the Mandla lavas which are chemically similar to the uppermost Poladpur, Ambenali and Mahabaleshwar Formation lavas of SW Deccan. Our study shows that the dyke activities occurred in two phases, with the second one representing the terminal stage.

  2. Feeder Voltage Regulation with High-Penetration PV Using Advanced Inverters and a Distribution Management System: A Duke Energy Case Study

    Energy Technology Data Exchange (ETDEWEB)

    Palmintier, Bryan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Giraldez, Julieta [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gruchalla, Kenny [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gotseff, Peter [National Renewable Energy Lab. (NREL), Golden, CO (United States); Nagarajan, Adarsh [National Renewable Energy Lab. (NREL), Golden, CO (United States); Harris, Tom [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bugbee, Bruce [National Renewable Energy Lab. (NREL), Golden, CO (United States); Baggu, Murali [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gantz, Jesse [GE Grid Solutions, Fairfield, CT (United States); Boardman, Ethan [GE Grid Solutions, Fairfield, CT (United States)

    2016-11-01

    Duke Energy, Alstom Grid, and the National Renewable Energy Laboratory teamed up to better understand the impacts of solar photovoltaics (PV) on distribution system operations. The core goal of the project is to compare the operational - specifically, voltage regulation - impacts of three classes of PV inverter operations: 1.) Active power only (Baseline); 2.) Local inverter control (e.g., PF...not equal...1, Q(V), etc.); and 3.) Integrated volt-VAR control (centralized through the distribution management system). These comparisons were made using multiple approaches, each of which represents an important research-and-development effort on its own: a) Quasi-steady-state time-series modeling for approximately 1 year of operations using the Alstom eTerra (DOTS) system as a simulation engine, augmented by Python scripting for scenario and time-series control and using external models for an advanced inverter; b) Power-hardware-in-the-loop (PHIL) testing of a 500-kVA-class advanced inverter and traditional voltage regulating equipment. This PHIL testing used cosimulation to link full-scale feeder simulation using DOTS in real time to hardware testing; c) Advanced visualization to provide improved insights into time-series results and other PV operational impacts; and d) Cost-benefit analysis to compare the financial and business-model impacts of each integration approach.

  3. Simulating Global AeroMACS Airport Ground Station Antenna Power Transmission Limits to Avoid Interference With Mobile Satellite Service Feeder Uplinks

    Science.gov (United States)

    Wilson, Jeffrey D.

    2013-01-01

    The Aeronautical Mobile Airport Communications System (AeroMACS), which is based upon the IEEE 802.16e mobile wireless standard, is expected to be implemented in the 5091 to 5150 MHz frequency band. As this band is also occupied by Mobile Satellite Service feeder uplinks, AeroMACS must be designed to avoid interference with this incumbent service. The aspects of AeroMACS operation that present potential interference are under analysis in order to enable the definition of standards that assure that such interference will be avoided. In this study, the cumulative interference power distribution at low Earth orbit from transmitters at global airports was simulated with the Visualyse Professional software. The dependence of the interference power on antenna distribution, gain patterns, duty cycle, and antenna tilt was simulated. As a function of these parameters, the simulation results are presented in terms of the limitations on transmitter power from global airports required to maintain the cumulative interference power under the established threshold.

  4. Constant DC-Capacitor Voltage-Control-Based Harmonics Compensation Strategy of Smart Charger for Electric Vehicles in Single-Phase Three-Wire Distribution Feeders

    Directory of Open Access Journals (Sweden)

    Fuka Ikeda

    2017-06-01

    Full Text Available This paper discusses harmonic current compensation of the constant DC-capacitor voltage-control (CDCVC-based strategy of smart chargers for electric vehicles (EVs in single-phase three-wire distribution feeders (SPTWDFs under nonlinear load conditions. The basic principle of the CDCVC-based harmonics compensation strategy under nonlinear load conditions is discussed in detail. The instantaneous power flowing into the three-leg pulse-width modulated (PWM rectifier, which performs as a smart charger, shows that the CDCVC-based strategy achieves balanced and sinusoidal source currents with a unity power factor. The CDCVC-based harmonics compensation strategy does not require any calculation blocks of fundamental reactive, unbalanced active, and harmonic currents. Thus, the authors propose a simplified algorithm to compensate for reactive, unbalanced active, and harmonic currents. A digital computer simulation is implemented to confirm the validity and high practicability of the CDCVC-based harmonics compensation strategy using PSIM software. Simulation results demonstrate that balanced and sinusoidal source currents with a unity power factor in SPTWDFs are obtained on the secondary side of the pole-mounted distribution transformer (PMDT during both the battery-charging and discharging operations in EVs, compensating for the reactive, unbalanced active, and harmonic currents.

  5. Multi-layer monochromator

    International Nuclear Information System (INIS)

    Schoenborn, B.P.; Caspar, D.L.D.

    1975-01-01

    This invention provides an artificial monochromator crystal for efficiently selecting a narrow band of neutron wavelengths from a neutron beam having a Maxwellian wavelength distribution, by providing on a substrate a plurality of germanium layers, and alternate periodic layers of a different metal having tailored thicknesses, shapes, and volumetric and neutron scattering densities. (U.S.)

  6. Ozone Layer Protection

    Science.gov (United States)

    ... and Research Centers Contact Us Share Ozone Layer Protection The stratospheric ozone layer is Earth’s “sunscreen” – protecting ... GreenChill Partnership Responsible Appliance Disposal (RAD) Program Ozone Protection vs. Ozone Pollution This website addresses stratospheric ozone ...

  7. Stable Boundary Layer Issues

    NARCIS (Netherlands)

    Steeneveld, G.J.

    2012-01-01

    Understanding and prediction of the stable atmospheric boundary layer is a challenging task. Many physical processes are relevant in the stable boundary layer, i.e. turbulence, radiation, land surface coupling, orographic turbulent and gravity wave drag, and land surface heterogeneity. The

  8. Development of boundary layers

    International Nuclear Information System (INIS)

    Herbst, R.

    1980-01-01

    Boundary layers develop along the blade surfaces on both the pressure and the suction side in a non-stationary flow field. This is due to the fact that there is a strongly fluctuating flow on the downstream blade row, especially as a result of the wakes of the upstream blade row. The author investigates the formation of boundary layers under non-stationary flow conditions and tries to establish a model describing the non-stationary boundary layer. For this purpose, plate boundary layers are measured, at constant flow rates but different interferent frequency and variable pressure gradients. By introducing the sample technique, measurements of the non-stationary boundary layer become possible, and the flow rate fluctuation can be divided in its components, i.e. stochastic turbulence and periodical fluctuation. (GL) [de

  9. Improved electron transport layer

    DEFF Research Database (Denmark)

    2012-01-01

    The present invention provides: a method of preparing a coating ink for forming a zinc oxide electron transport layer, comprising mixing zinc acetate and a wetting agent in water or methanol; a coating ink comprising zinc acetate and a wetting agent in aqueous solution or methanolic solution......; a method of preparing a zinc oxide electron transporting layer, which method comprises: i) coating a substrate with the coating ink of the present invention to form a film; ii) drying the film; and iii) heating the dry film to convert the zinc acetate substantially to ZnO; a method of preparing an organic...... photovoltaic device or an organic LED having a zinc oxide electron transport layer, the method comprising, in this order: a) providing a substrate bearing a first electrode layer; b) forming an electron transport layer according to the following method: i) coating a coating ink comprising an ink according...

  10. Efficient and Cost-Effective Generation of Mature Neurons From Human Induced Pluripotent Stem Cells

    OpenAIRE

    Badja , Cherif; Maleeva , Galyna; El-Yazidi , Claire; Barruet , Emilie; Lasserre , Manon; Tropel , Philippe; Binetruy , Bernard; Bregestovski , Piotr; Magdinier , Frédérique

    2014-01-01

    The authors describe a feeder-free method of generating induced pluripotent stem cells by relying on the use of a chemically defined medium that overcomes the need for embryoid body formation and neuronal rosette isolation for neuronal precursors and terminally differentiated neuron production. This specific and efficient single-step strategy allows the production of mature neurons in 20–40 days with multiple applications, especially for modeling human pathologies.

  11. Boosting water oxidation layer-by-layer.

    Science.gov (United States)

    Hidalgo-Acosta, Jonnathan C; Scanlon, Micheál D; Méndez, Manuel A; Amstutz, Véronique; Vrubel, Heron; Opallo, Marcin; Girault, Hubert H

    2016-04-07

    Electrocatalysis of water oxidation was achieved using fluorinated tin oxide (FTO) electrodes modified with layer-by-layer deposited films consisting of bilayers of negatively charged citrate-stabilized IrO2 NPs and positively charged poly(diallyldimethylammonium chloride) (PDDA) polymer. The IrO2 NP surface coverage can be fine-tuned by controlling the number of bilayers. The IrO2 NP films were amorphous, with the NPs therein being well-dispersed and retaining their as-synthesized shape and sizes. UV/vis spectroscopic and spectro-electrochemical studies confirmed that the total surface coverage and electrochemically addressable surface coverage of IrO2 NPs increased linearly with the number of bilayers up to 10 bilayers. The voltammetry of the modified electrode was that of hydrous iridium oxide films (HIROFs) with an observed super-Nernstian pH response of the Ir(III)/Ir(IV) and Ir(IV)-Ir(IV)/Ir(IV)-Ir(V) redox transitions and Nernstian shift of the oxygen evolution onset potential. The overpotential of the oxygen evolution reaction (OER) was essentially pH independent, varying only from 0.22 V to 0.28 V (at a current density of 0.1 mA cm(-2)), moving from acidic to alkaline conditions. Bulk electrolysis experiments revealed that the IrO2/PDDA films were stable and adherent under acidic and neutral conditions but degraded in alkaline solutions. Oxygen was evolved with Faradaic efficiencies approaching 100% under acidic (pH 1) and neutral (pH 7) conditions, and 88% in alkaline solutions (pH 13). This layer-by-layer approach forms the basis of future large-scale OER electrode development using ink-jet printing technology.

  12. The Application of Layer Theory to Design: The Control Layer

    Science.gov (United States)

    Gibbons, Andrew S.; Langton, Matthew B.

    2016-01-01

    A theory of design layers proposed by Gibbons ("An Architectural Approach to Instructional Design." Routledge, New York, 2014) asserts that each layer of an instructional design is related to a body of theory closely associated with the concerns of that particular layer. This study focuses on one layer, the control layer, examining…

  13. Microstructure analysis of zirconium carbide layer on pyrocarbon-coated particles prepared by zirconium chloride vapor method

    International Nuclear Information System (INIS)

    Zhao Hongsheng; Liu Bing; Zhang Kaihong; Tang Chunhe

    2012-01-01

    Zirconium carbide (ZrC) layer on pyrocarbon-coated particles was successfully prepared in a fluidized bed coater furnace by chemical vapor deposition using a zirconium chloride (ZrCl 4 ) vapor method and quantitative controlling of the Zr-source through a ZrCl 4 powder feeder. The crystal phase, microstructure and chemical composition of ZrC-coating layer were analyzed using X-ray diffraction (XRD), optical metallographical microscope, scanning electron microscope (SEM), transmission electron microscope (TEM), high-resolution transmission electron microscope (HR-TEM) and X-ray photoelectron spectroscopy (XPS). The results show that the deposited ZrC-coating layer has smooth and compact surface, no obvious holes, clear interface with dense pyrocarbon layer, and a thickness of 35 μm. The main phase of ZrC-coating layer is fcc-ZrC crystal, which is composed of small grains with the size of 20–50 nm. The grain size increases monotonously with the deposition temperature increasing. The main elements of ZrC-coating layer are Zr and C, and the Zr/C molar ratio is close to 1:1. The analysis of composition and crystal structure suggest that a stoichiometric fcc-ZrC crystal was obtained and no obvious preferred orientation of the grains was found.

  14. Topologically nontrivial quantum layers

    International Nuclear Information System (INIS)

    Carron, G.; Exner, P.; Krejcirik, D.

    2004-01-01

    Given a complete noncompact surface Σ embedded in R 3 , we consider the Dirichlet Laplacian in the layer Ω that is defined as a tubular neighborhood of constant width about Σ. Using an intrinsic approach to the geometry of Ω, we generalize the spectral results of the original paper by Duclos et al. [Commun. Math. Phys. 223, 13 (2001)] to the situation when Σ does not possess poles. This enables us to consider topologically more complicated layers and state new spectral results. In particular, we are interested in layers built over surfaces with handles or several cylindrically symmetric ends. We also discuss more general regions obtained by compact deformations of certain Ω

  15. Mesenchymal stem cell like (MSCl) cells generated from human embryonic stem cells support pluripotent cell growth

    Energy Technology Data Exchange (ETDEWEB)

    Varga, Nora [Membrane Research Group of the Hungarian Academy of Sciences, Semmelweis University, Budapest (Hungary); Vereb, Zoltan; Rajnavoelgyi, Eva [Department of Immunology, Medical and Health Science Centre, University of Debrecen, Debrecen (Hungary); Nemet, Katalin; Uher, Ferenc; Sarkadi, Balazs [Membrane Research Group of the Hungarian Academy of Sciences, Semmelweis University, Budapest (Hungary); Apati, Agota, E-mail: apati@kkk.org.hu [Membrane Research Group of the Hungarian Academy of Sciences, Semmelweis University, Budapest (Hungary)

    2011-10-28

    Highlights: Black-Right-Pointing-Pointer MSC like cells were derived from hESC by a simple and reproducible method. Black-Right-Pointing-Pointer Differentiation and immunosuppressive features of MSCl cells were similar to bmMSC. Black-Right-Pointing-Pointer MSCl cells as feeder cells support the undifferentiated growth of hESC. -- Abstract: Mesenchymal stem cell like (MSCl) cells were generated from human embryonic stem cells (hESC) through embryoid body formation, and isolated by adherence to plastic surface. MSCl cell lines could be propagated without changes in morphological or functional characteristics for more than 15 passages. These cells, as well as their fluorescent protein expressing stable derivatives, efficiently supported the growth of undifferentiated human embryonic stem cells as feeder cells. The MSCl cells did not express the embryonic (Oct4, Nanog, ABCG2, PODXL, or SSEA4), or hematopoietic (CD34, CD45, CD14, CD133, HLA-DR) stem cell markers, while were positive for the characteristic cell surface markers of MSCs (CD44, CD73, CD90, CD105). MSCl cells could be differentiated toward osteogenic, chondrogenic or adipogenic directions and exhibited significant inhibition of mitogen-activated lymphocyte proliferation, and thus presented immunosuppressive features. We suggest that cultured MSCl cells can properly model human MSCs and be applied as efficient feeders in hESC cultures.

  16. Mesenchymal stem cell like (MSCl) cells generated from human embryonic stem cells support pluripotent cell growth

    International Nuclear Information System (INIS)

    Varga, Nóra; Veréb, Zoltán; Rajnavölgyi, Éva; Német, Katalin; Uher, Ferenc; Sarkadi, Balázs; Apáti, Ágota

    2011-01-01

    Highlights: ► MSC like cells were derived from hESC by a simple and reproducible method. ► Differentiation and immunosuppressive features of MSCl cells were similar to bmMSC. ► MSCl cells as feeder cells support the undifferentiated growth of hESC. -- Abstract: Mesenchymal stem cell like (MSCl) cells were generated from human embryonic stem cells (hESC) through embryoid body formation, and isolated by adherence to plastic surface. MSCl cell lines could be propagated without changes in morphological or functional characteristics for more than 15 passages. These cells, as well as their fluorescent protein expressing stable derivatives, efficiently supported the growth of undifferentiated human embryonic stem cells as feeder cells. The MSCl cells did not express the embryonic (Oct4, Nanog, ABCG2, PODXL, or SSEA4), or hematopoietic (CD34, CD45, CD14, CD133, HLA-DR) stem cell markers, while were positive for the characteristic cell surface markers of MSCs (CD44, CD73, CD90, CD105). MSCl cells could be differentiated toward osteogenic, chondrogenic or adipogenic directions and exhibited significant inhibition of mitogen-activated lymphocyte proliferation, and thus presented immunosuppressive features. We suggest that cultured MSCl cells can properly model human MSCs and be applied as efficient feeders in hESC cultures.

  17. Arctic Mixed Layer Dynamics

    National Research Council Canada - National Science Library

    Morison, James

    2003-01-01

    .... Over the years we have sought to understand the heat and mass balance of the mixed layer, marginal ice zone processes, the Arctic internal wave and mixing environment, summer and winter leads, and convection...

  18. Layered inorganic solids

    Czech Academy of Sciences Publication Activity Database

    Čejka, Jiří; Morris, R. E.; Nachtigall, P.; Roth, Wieslaw Jerzy

    2014-01-01

    Roč. 43, č. 27 (2014), s. 10274-10275 ISSN 1477-9226 Institutional support: RVO:61388955 Keywords : layered inorganic solids * physical chemistry * catalysis Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 4.197, year: 2014

  19. Addressing Ozone Layer Depletion

    Science.gov (United States)

    Access information on EPA's efforts to address ozone layer depletion through regulations, collaborations with stakeholders, international treaties, partnerships with the private sector, and enforcement actions under Title VI of the Clean Air Act.

  20. Layered Fault Management Architecture

    National Research Council Canada - National Science Library

    Sztipanovits, Janos

    2004-01-01

    ... UAVs or Organic Air Vehicles. The approach of this effort was to analyze fault management requirements of formation flight for fleets of UAVs, and develop a layered fault management architecture which demonstrates significant...

  1. The Bottom Boundary Layer.

    Science.gov (United States)

    Trowbridge, John H; Lentz, Steven J

    2018-01-03

    The oceanic bottom boundary layer extracts energy and momentum from the overlying flow, mediates the fate of near-bottom substances, and generates bedforms that retard the flow and affect benthic processes. The bottom boundary layer is forced by winds, waves, tides, and buoyancy and is influenced by surface waves, internal waves, and stratification by heat, salt, and suspended sediments. This review focuses on the coastal ocean. The main points are that (a) classical turbulence concepts and modern turbulence parameterizations provide accurate representations of the structure and turbulent fluxes under conditions in which the underlying assumptions hold, (b) modern sensors and analyses enable high-quality direct or near-direct measurements of the turbulent fluxes and dissipation rates, and (c) the remaining challenges include the interaction of waves and currents with the erodible seabed, the impact of layer-scale two- and three-dimensional instabilities, and the role of the bottom boundary layer in shelf-slope exchange.

  2. The Bottom Boundary Layer

    Science.gov (United States)

    Trowbridge, John H.; Lentz, Steven J.

    2018-01-01

    The oceanic bottom boundary layer extracts energy and momentum from the overlying flow, mediates the fate of near-bottom substances, and generates bedforms that retard the flow and affect benthic processes. The bottom boundary layer is forced by winds, waves, tides, and buoyancy and is influenced by surface waves, internal waves, and stratification by heat, salt, and suspended sediments. This review focuses on the coastal ocean. The main points are that (a) classical turbulence concepts and modern turbulence parameterizations provide accurate representations of the structure and turbulent fluxes under conditions in which the underlying assumptions hold, (b) modern sensors and analyses enable high-quality direct or near-direct measurements of the turbulent fluxes and dissipation rates, and (c) the remaining challenges include the interaction of waves and currents with the erodible seabed, the impact of layer-scale two- and three-dimensional instabilities, and the role of the bottom boundary layer in shelf-slope exchange.

  3. Generation of functional cardiomyocytes from rat embryonic and induced pluripotent stem cells using feeder-free expansion and differentiation in suspension culture.

    Science.gov (United States)

    Dahlmann, Julia; Awad, George; Dolny, Carsten; Weinert, Sönke; Richter, Karin; Fischer, Klaus-Dieter; Munsch, Thomas; Leßmann, Volkmar; Volleth, Marianne; Zenker, Martin; Chen, Yaoyao; Merkl, Claudia; Schnieke, Angelika; Baraki, Hassina; Kutschka, Ingo; Kensah, George

    2018-01-01

    The possibility to generate cardiomyocytes from pluripotent stem cells in vitro has enormous significance for basic research, disease modeling, drug development and heart repair. The concept of heart muscle reconstruction has been studied and optimized in the rat model using rat primary cardiovascular cells or xenogeneic pluripotent stem cell derived-cardiomyocytes for years. However, the lack of rat pluripotent stem cells (rPSCs) and their cardiovascular derivatives prevented the establishment of an authentic clinically relevant syngeneic or allogeneic rat heart regeneration model. In this study, we comparatively explored the potential of recently available rat embryonic stem cells (rESCs) and induced pluripotent stem cells (riPSCs) as a source for cardiomyocytes (CMs). We developed feeder cell-free culture conditions facilitating the expansion of undifferentiated rPSCs and initiated cardiac differentiation by embryoid body (EB)-formation in agarose microwell arrays, which substituted the robust but labor-intensive hanging drop (HD) method. Ascorbic acid was identified as an efficient enhancer of cardiac differentiation in both rPSC types by significantly increasing the number of beating EBs (3.6 ± 1.6-fold for rESCs and 17.6 ± 3.2-fold for riPSCs). These optimizations resulted in a differentiation efficiency of up to 20% cTnTpos rPSC-derived CMs. CMs showed spontaneous contractions, expressed cardiac markers and had typical morphological features. Electrophysiology of riPSC-CMs revealed different cardiac subtypes and physiological responses to cardio-active drugs. In conclusion, we describe rPSCs as a robust source of CMs, which is a prerequisite for detailed preclinical studies of myocardial reconstruction in a physiologically and immunologically relevant small animal model.

  4. Spatio-Temporal Variation in Effects of Upwelling on the Fatty Acid Composition of Benthic Filter Feeders in the Southern Benguela Ecosystem: Not All Upwelling Is Equal.

    Directory of Open Access Journals (Sweden)

    Eleonora Puccinelli

    Full Text Available Variability in mesoscale nearshore oceanographic conditions plays an important role in the distribution of primary production and food availability for intertidal consumers. Advection of nutrient rich waters by upwelling usually allows the proliferation of diatoms, later replaced by dinoflagellates. We examined upwelling effects on the fatty acid (FA signature of a benthic intertidal filter feeder to identify its response to pulsed variability in food availability. The study took place in two contrasting seasons and at two upwelling and two non-upwelling sites interspersed within the southern Benguela upwelling system of South Africa. We investigated the FA composition of the adductor muscles and gonads of the mussel Mytilus galloprovincialis to assess how FA are apportioned to the different tissues and whether this changes between upwelling and non-upwelling conditions. In situ temperature loggers used to identify upwelling conditions at the four sites indicated that such events occurred only at the upwelling centres and only in summer. Tissues differed strongly, with gonads presenting a higher proportion of essential FAs. This could reflect the faster turnover rate of gonad tissue or preferential retention of specific FA for reproductive purposes. FA composition did not vary as a direct function of upwelling, but there were strong dissimilarities among sites. Upwelling influenced mussel diets at one upwelling site while at the other, the expected signature of upwelling was displaced downstream of the core of upwelling. Condition Index (CI and Gonad Index (GI differed among sites and were not influenced by upwelling, with GI being comparable among sites. In addition, FA proportions were consistent among sites, indicating similar food quality and quantity over time and under upwelling and non-upwelling conditions. This suggests that the influence of upwelling on the west coast of South Africa is pervasive and diffuse, rather than discrete; while

  5. Stability of mixing layers

    Science.gov (United States)

    Tam, Christopher; Krothapalli, A

    1993-01-01

    The research program for the first year of this project (see the original research proposal) consists of developing an explicit marching scheme for solving the parabolized stability equations (PSE). Performing mathematical analysis of the computational algorithm including numerical stability analysis and the determination of the proper boundary conditions needed at the boundary of the computation domain are implicit in the task. Before one can solve the parabolized stability equations for high-speed mixing layers, the mean flow must first be found. In the past, instability analysis of high-speed mixing layer has mostly been performed on mean flow profiles calculated by the boundary layer equations. In carrying out this project, it is believed that the boundary layer equations might not give an accurate enough nonparallel, nonlinear mean flow needed for parabolized stability analysis. A more accurate mean flow can, however, be found by solving the parabolized Navier-Stokes equations. The advantage of the parabolized Navier-Stokes equations is that its accuracy is consistent with the PSE method. Furthermore, the method of solution is similar. Hence, the major part of the effort of the work of this year has been devoted to the development of an explicit numerical marching scheme for the solution of the Parabolized Navier-Stokes equation as applied to the high-seed mixing layer problem.

  6. Layers of Neuroscience

    NARCIS (Netherlands)

    Dumoulin, Serge O

    2017-01-01

    In a patch of cortex, laminae connect to different parts of the brain. Huber et al. (2017) demonstrate the ability of human neuroimaging to derive laminar information flow between brain regions, paving the way for human neuroscience applications.

  7. Three-layer magnetoconvection

    International Nuclear Information System (INIS)

    Lin, M.-K.; Silvers, L.J.; Proctor, M.R.E.

    2008-01-01

    It is believed that some stars have two or more convection zones in close proximity near to the stellar photosphere. These zones are separated by convectively stable regions that are relatively narrow. Due to the close proximity of these regions it is important to construct mathematical models to understand the transport and mixing of passive and dynamic quantities. One key quantity of interest is a magnetic field, a dynamic vector quantity, that can drastically alter the convectively driven flows, and have an important role in coupling the different layers. In this Letter we present the first investigation into the effect of an imposed magnetic field in such a geometry. We focus our attention on the effect of field strength and show that, while there are some similarities with results for magnetic field evolution in a single layer, new and interesting phenomena are also present in a three layer system

  8. Layered tin dioxide microrods

    International Nuclear Information System (INIS)

    Duan Junhong; Huang Hongbo; Gong Jiangfeng; Zhao Xiaoning; Cheng Guangxu; Yang Shaoguang

    2007-01-01

    Single-crystalline layered SnO 2 microrods were synthesized by a simple tin-water reaction at 900 deg. C. The structural and optical properties of the sample were characterized by x-ray powder diffraction, energy-dispersive x-ray spectroscopy, scanning electron microscopy, high resolution transmission electron microscopy, Raman scattering and photoluminescence (PL) spectroscopy. High resolution transmission electron microscopy studies and selected area electron diffraction patterns revealed that the layered SnO 2 microrods are single crystalline and their growth direction is along [1 1 0]. The growth mechanism of the microrods was proposed based on SEM, TEM characterization and thermodynamic analysis. It is deduced that the layered microrods grow by the stacking of SnO 2 sheets with a (1 1 0) surface in a vapour-liquid-solid process. Three emission peaks at 523, 569 and 626 nm were detected in room-temperature PL measurements

  9. Superfluid Boundary Layer.

    Science.gov (United States)

    Stagg, G W; Parker, N G; Barenghi, C F

    2017-03-31

    We model the superfluid flow of liquid helium over the rough surface of a wire (used to experimentally generate turbulence) profiled by atomic force microscopy. Numerical simulations of the Gross-Pitaevskii equation reveal that the sharpest features in the surface induce vortex nucleation both intrinsically (due to the raised local fluid velocity) and extrinsically (providing pinning sites to vortex lines aligned with the flow). Vortex interactions and reconnections contribute to form a dense turbulent layer of vortices with a nonclassical average velocity profile which continually sheds small vortex rings into the bulk. We characterize this layer for various imposed flows. As boundary layers conventionally arise from viscous forces, this result opens up new insight into the nature of superflows.

  10. Generation of Human Induced Pluripotent Stem Cells Using RNA-Based Sendai Virus System and Pluripotency Validation of the Resulting Cell Population.

    Science.gov (United States)

    Chichagova, Valeria; Sanchez-Vera, Irene; Armstrong, Lyle; Steel, David; Lako, Majlinda

    2016-01-01

    Human induced pluripotent stem cells (hiPSCs) provide a platform for studying human disease in vitro, increase our understanding of human embryonic development, and provide clinically relevant cell types for transplantation, drug testing, and toxicology studies. Since their discovery, numerous advances have been made in order to eliminate issues such as vector integration into the host genome, low reprogramming efficiency, incomplete reprogramming and acquisition of genomic instabilities. One of the ways to achieve integration-free reprogramming is by using RNA-based Sendai virus. Here we describe a method to generate hiPSCs with Sendai virus in both feeder-free and feeder-dependent culture systems. Additionally, we illustrate methods by which to validate pluripotency of the resulting stem cell population.

  11. Layered semiconductor neutron detectors

    Science.gov (United States)

    Mao, Samuel S; Perry, Dale L

    2013-12-10

    Room temperature operating solid state hand held neutron detectors integrate one or more relatively thin layers of a high neutron interaction cross-section element or materials with semiconductor detectors. The high neutron interaction cross-section element (e.g., Gd, B or Li) or materials comprising at least one high neutron interaction cross-section element can be in the form of unstructured layers or micro- or nano-structured arrays. Such architecture provides high efficiency neutron detector devices by capturing substantially more carriers produced from high energy .alpha.-particles or .gamma.-photons generated by neutron interaction.

  12. Geometric design of part feeders

    NARCIS (Netherlands)

    Berretty, R.-P.M.

    2000-01-01

    This thesis presents solutions for problems derived from industrial assembly and robotic manipulation. The basic tasks in a factory are manufacturing the parts, and combining them into the desired product. In automating these tasks, we want to use robot manipulators that require little or no

  13. Quasi-static time-series simulation using OpenDSS in IEEE distribution feeder model with high PV penetration and its impact on solar forecasting

    Science.gov (United States)

    Mohammed, Touseef Ahmed Faisal

    Distribution System Simulator developed by Electric Power Research Institute, to simulate grid voltage profile with a large scale PV system under quasi-static time series considering variations of PV output in seconds, minutes, and the average daily load variations. A 13 bus IEEE distribution feeder model is utilized with distributed residential and commercial scale PV at different buses for simulation studies. Time series simulations are discussed for various modes of operation considering dynamic PV penetration at different time periods in a day. In addition, this thesis demonstrates simulations taking into account the presence of moving cloud for solar forecasting studies.

  14. Physical layer network coding

    DEFF Research Database (Denmark)

    Fukui, Hironori; Popovski, Petar; Yomo, Hiroyuki

    2014-01-01

    Physical layer network coding (PLNC) has been proposed to improve throughput of the two-way relay channel, where two nodes communicate with each other, being assisted by a relay node. Most of the works related to PLNC are focused on a simple three-node model and they do not take into account...

  15. Thin layer activation

    International Nuclear Information System (INIS)

    Schweickert, H.; Fehsenfeld, P.

    1995-01-01

    The reliability of industrial equip ment is substantially influenced by wear and corrosion; monitoring can prevent accidents and avoid down-time. One powerful tool is thin layer activation analysis (TLA) using accelerator systems. The information is used to improve mechanical design and material usage; the technology is used by many large companies, particularly in the automotive industry, e.g. Daimler Benz. A critical area of a machine component receives a thin layer of radioactivity by irradiation with charged particles from an accelerator - usually a cyclotron. The radioactivity can be made homogeneous by suitable selection of particle, beam energy and angle of incidence. Layer thickness can be varied from 20 microns to around 1 mm with different depth distributions; the position and size of the wear zone can be set to within 0.1 mm. The machine is then reassembled and operated so that wear can be measured. An example is a combustion engine comprising piston ring, cylinder wall, cooling water jacket and housing wall, where wear measurements on the cylinder wall are required in a critical zone around the dead-point of the piston ring. Proton beam bombardment creates a radioactive layer whose thickness is known accurately, and characteristic gamma radiation from this radioactive zone penetrates through the engine and is detected externally. Measurements can be made either of the activity removed from the surface, or of the (reduced) residual activity; wear measurement of the order of 10 -9 metres is possible

  16. Our Shrinking Ozone Layer

    Indian Academy of Sciences (India)

    Depletion of the ozone layer is therefore having significant effects on life on .... but there is always a net balance between the rate of formation and destruction ..... award of Commonwealth Fellowship during the present work and also being an ...

  17. Layer-Cake Earth

    Science.gov (United States)

    Tedford, Rebecca; Warny, Sophie

    2006-01-01

    In this article, the authors offer a safe, fun, effective way to introduce geology concepts to elementary school children of all ages: "coring" layer cakes. This activity introduces the concepts and challenges that geologists face and at the same time strengthens students' inferential, observational, and problem-solving skills. It also addresses…

  18. Layered double hydroxides

    DEFF Research Database (Denmark)

    López Rayo, Sandra; Imran, Ahmad; Hansen, Hans Chr. Bruun

    2017-01-01

    A novel zinc (Zn) fertilizer concept based on Zn doped layered double hydroxides (Zn-doped Mg-Fe-LDHs) has been investigated. Zn-doped Mg-Fe-LDHs were synthetized, their chemical composition was analyzed and their nutrient release was studied in buffered solutions with different pH values. Uptake...

  19. MITRE sensor layer prototype

    Science.gov (United States)

    Duff, Francis; McGarry, Donald; Zasada, David; Foote, Scott

    2009-05-01

    The MITRE Sensor Layer Prototype is an initial design effort to enable every sensor to help create new capabilities through collaborative data sharing. By making both upstream (raw) and downstream (processed) sensor data visible, users can access the specific level, type, and quantities of data needed to create new data products that were never anticipated by the original designers of the individual sensors. The major characteristic that sets sensor data services apart from typical enterprise services is the volume (on the order of multiple terabytes) of raw data that can be generated by most sensors. Traditional tightly coupled processing approaches extract pre-determined information from the incoming raw sensor data, format it, and send it to predetermined users. The community is rapidly reaching the conclusion that tightly coupled sensor processing loses too much potentially critical information.1 Hence upstream (raw and partially processed) data must be extracted, rapidly archived, and advertised to the enterprise for unanticipated uses. The authors believe layered sensing net-centric integration can be achieved through a standardize-encapsulate-syndicateaggregate- manipulate-process paradigm. The Sensor Layer Prototype's technical approach focuses on implementing this proof of concept framework to make sensor data visible, accessible and useful to the enterprise. To achieve this, a "raw" data tap between physical transducers associated with sensor arrays and the embedded sensor signal processing hardware and software has been exploited. Second, we encapsulate and expose both raw and partially processed data to the enterprise within the context of a service-oriented architecture. Third, we advertise the presence of multiple types, and multiple layers of data through geographic-enabled Really Simple Syndication (GeoRSS) services. These GeoRSS feeds are aggregated, manipulated, and filtered by a feed aggregator. After filtering these feeds to bring just the type

  20. Human neural progenitor cells decrease photoreceptor degeneration, normalize opsin distribution and support synapse structure in cultured porcine retina.

    Science.gov (United States)

    Mollick, Tanzina; Mohlin, Camilla; Johansson, Kjell

    2016-09-01

    Retinal neurodegenerative disorders like retinitis pigmentosa, age-related macular degeneration, diabetic retinopathy and retinal detachment decrease retinal functionality leading to visual impairment. The pathological events are characterized by photoreceptor degeneration, synaptic disassembly, remodeling of postsynaptic neurons and activation of glial cells. Despite intense research, no effective treatment has been found for these disorders. The current study explores the potential of human neural progenitor cell (hNPC) derived factors to slow the degenerative processes in adult porcine retinal explants. Retinas were cultured for 3 days with or without hNPCs as a feeder layer and investigated by terminal deoxynucleotidyl transferase dUTP nick end labeling (TUNEL), immunohistochemical, western blot and quantitative real time-polymerase chain reaction (qRT-PCR) techniques. TUNEL showed that hNPCs had the capacity to limit photoreceptor cell death. Among cone photoreceptors, hNPC coculture resulted in better maintenance of cone outer segments and reduced opsin mislocalization. Additionally, maintained synaptic structural integrity and preservation of second order calbindin positive horizontal cells was also observed. However, Müller cell gliosis only seemed to be alleviated in terms of reduced Müller cell density. Our observations indicate that at 3 days of coculture, hNPC derived factors had the capacity to protect photoreceptors, maintain synaptic integrity and support horizontal cell survival. Human neural progenitor cell applied treatment modalities may be an effective strategy to help maintain retinal functionality in neurodegenerative pathologies. Whether hNPCs can independently hinder Müller cell gliosis by utilizing higher concentrations or by combination with other pharmacological agents still needs to be determined. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. How to insure measurement accuracy of belt feeder machine weighing installment%如何保证皮带绐料机称重装置的计量精度

    Institute of Scientific and Technical Information of China (English)

    李双; 吴江; 陈以振

    2012-01-01

    本文从皮带给料机这一称重产品的结构、校准原理、计量精度等几个主要方面,以图文结合的形式着重阐述了怎样保证皮带给料机称重装置的计量精度。%In the form of a graphic combination, according to structure, calibration principle, measurement accuracy and some other factors, this article elaborates how to insure measurement accuracy of belt feeder machine weighing installmenL

  2. An avoidance layer in hierarchical process control

    International Nuclear Information System (INIS)

    De Callatay, A.

    1994-01-01

    A project of layered software architecture is proposed: a safety-critical real-time non-stop simple kernel system includes a layer avoiding threatening actions from operators or programs in other control systems. Complex process-control applications (such as fuzzy systems) are useful for the smooth operation of the system, optimum productivity, efficient diagnostics, and safe management of degraded modes of operation. Defects in these complex process-control applications do not have an impact on safety if their commands have first to be accepted by a safety-critical module. The development, testing, and certification of complex applications computed in the outside layers can be made simpler and less expensive than for those in the kernel. Avoidance systems use rule-base systems having negative fuzzy conditions and actions. Animal and human behaviour cannot be explained without active avoidance

  3. Peeling Back the Layers

    Science.gov (United States)

    2004-01-01

    NASA's Mars Exploration Rover Spirit took this panoramic camera image of the rock target named 'Mazatzal' on sol 77 (March 22, 2004). It is a close-up look at the rock face and the targets that will be brushed and ground by the rock abrasion tool in upcoming sols. Mazatzal, like most rocks on Earth and Mars, has layers of material near its surface that provide clues about the history of the rock. Scientists believe that the top layer of Mazatzal is actually a coating of dust and possibly even salts. Under this light coating may be a more solid portion of the rock that has been chemically altered by weathering. Past this layer is the unaltered rock, which may give scientists the best information about how Mazatzal was formed. Because each layer reveals information about the formation and subsequent history of Mazatzal, it is important that scientists get a look at each of them. For this reason, they have developed a multi-part strategy to use the rock abrasion tool to systematically peel back Mazatzal's layers and analyze what's underneath with the rover's microscopic imager, and its Moessbauer and alpha particle X-ray spectrometers. The strategy began on sol 77 when scientists used the microscopic imager to get a closer look at targets on Mazatzal named 'New York,' 'Illinois' and 'Arizona.' These rock areas were targeted because they posed the best opportunity for successfully using the rock abrasion tool; Arizona also allowed for a close-up look at a range of tones. On sol 78, Spirit's rock abrasion tool will do a light brushing on the Illinois target to preserve some of the surface layers. Then, a brushing of the New York target should remove the top coating of any dust and salts and perhaps reveal the chemically altered rock underneath. Finally, on sol 79, the rock abrasion tool will be commanded to grind into the New York target, which will give scientists the best chance of observing Mazatzal's interior. The Mazatzal targets were named after the home states of

  4. Physical Layer Network Coding

    DEFF Research Database (Denmark)

    Fukui, Hironori; Yomo, Hironori; Popovski, Petar

    2013-01-01

    of interfering nodes and usage of spatial reservation mechanisms. Specifically, we introduce a reserved area in order to protect the nodes involved in two-way relaying from the interference caused by neighboring nodes. We analytically derive the end-to-end rate achieved by PLNC considering the impact......Physical layer network coding (PLNC) has the potential to improve throughput of multi-hop networks. However, most of the works are focused on the simple, three-node model with two-way relaying, not taking into account the fact that there can be other neighboring nodes that can cause....../receive interference. The way to deal with this problem in distributed wireless networks is usage of MAC-layer mechanisms that make a spatial reservation of the shared wireless medium, similar to the well-known RTS/CTS in IEEE 802.11 wireless networks. In this paper, we investigate two-way relaying in presence...

  5. Crack layer theory

    Science.gov (United States)

    Chudnovsky, A.

    1987-01-01

    A damage parameter is introduced in addition to conventional parameters of continuum mechanics and consider a crack surrounded by an array of microdefects within the continuum mechanics framework. A system consisting of the main crack and surrounding damage is called crack layer (CL). Crack layer propagation is an irreversible process. The general framework of the thermodynamics of irreversible processes are employed to identify the driving forces (causes) and to derive the constitutive equation of CL propagation, that is, the relationship between the rates of the crack growth and damage dissemination from one side and the conjugated thermodynamic forces from another. The proposed law of CL propagation is in good agreement with the experimental data on fatigue CL propagation in various materials. The theory also elaborates material toughness characterization.

  6. Gravitational double layers

    International Nuclear Information System (INIS)

    Senovilla, José M M

    2014-01-01

    I analyze the properties of thin shells through which the scalar curvature R is discontinuous in gravity theories with Lagrangian F(R) = R − 2Λ + αR 2 on the bulk. These shells/domain walls are of a new kind because they possess, in addition to the standard energy–momentum tensor, an external energy flux vector, an external scalar pressure/tension and, most exotic of all, another energy–momentum contribution resembling classical dipole distributions on a shell: a double layer. I prove that all these contributions are necessary to make the entire energy–momentum tensor divergence-free. This is the first known occurrence of such a type of double layer in a gravity theory. I present explicit examples in constant-curvature five-dimensional bulks, with a brief study of their properties: new physical behaviors arise. (fast track communications)

  7. Boundary-layer theory

    CERN Document Server

    Schlichting (Deceased), Hermann

    2017-01-01

    This new edition of the near-legendary textbook by Schlichting and revised by Gersten presents a comprehensive overview of boundary-layer theory and its application to all areas of fluid mechanics, with particular emphasis on the flow past bodies (e.g. aircraft aerodynamics). The new edition features an updated reference list and over 100 additional changes throughout the book, reflecting the latest advances on the subject.

  8. Barrier layer arrangement for conductive layers on silicon substrates

    International Nuclear Information System (INIS)

    Hung, L.S.; Agostinelli, J.A.

    1990-01-01

    This patent describes a circuit element comprised of a silicon substrate and a conductive layer located on the substrate. It is characterized in that the conductive layer consists essentially of a rare earth alkaline earth copper oxide and a barrier layer triad is interposed between the silicon substrate and the conductive layer comprised of a first triad layer located adjacent the silicon substrate consisting essentially of silica, a third triad layer remote from the silicon substrate consisting essentially of a least one Group 4 heavy metal oxide, and a second triad layer interposed between the first and third triad layers consisting essentially of a mixture of silica and at lease one Group 4 heavy metal oxide

  9. Feeding response of Aedes aegypti and Anopheles dirus (Diptera: Culicidae) using out-of-date human blood in a membrane feeding apparatus.

    Science.gov (United States)

    Pothikasikorn, Jinrapa; Boonplueang, Rapee; Suebsaeng, Chalermchai; Khaengraeng, Rungpetch; Chareonviriyaphap, Theeraphap

    2010-06-01

    The colonization of Aedes aegypti and Anopheles dirus was performed using out-of-date human blood from a blood bank as a nutritional supply dispensed from a common artificial feeder. Preserved human blood was collected and used for feeding on days 5, 15, and 25 after date of expiration and dispensed from a common artificial feeder to rear the mosquitoes. Ae. aegypti had a feeding rate of 78.7, 62, and 18% at the respective intervals while An. dirus had a rate of 80, 56.8, and 7.3% on the same respective days. Direct feeding on live hamsters resulted in a rate of 96 and 90% for Ae. aegypti and An. dirus, respectively. Although egg production rates decreased from the day 5 feeding to the day 25 feeding, all of the developmental stages resulting from An. dirus fed at day 5 and 15 showed insignificant differences when compared with direct feeding on the blood of a hamster.

  10. The SYOEKSY research project. Electrically-powered vehicles in ring rail line feeder traffic and short-distance travel; Saehkoeiset ajoneuvot kehaeradan syoettoe- ja asiointiliikenteessae. SYOEKSY-tutkimushankkeen loppuraportti 21.9.2011

    Energy Technology Data Exchange (ETDEWEB)

    2011-07-01

    The research report is divided into three sections: a general description of the project, separate reports on each of the themes investigated and a summary of the research results and recommendations. Section 2 deals with themes such as: Low-emissions-technology solutions for traffic and their technical prerequisites in an urban environment and the results obtained from pilot projects. New service models based on electrically-powered traffic technology with an assessment of their feasibility and their effect on urban infrastructure and levels of CO{sub 2} emissions. User needs in new feeder traffic, short-distance travel and other journeys on personal business together with proposals for planning measures which will promote sustainable mobility in new residential areas. The prerequisites for electrically-powered feeder traffic and short-distance travel are therefore handled in a wide-ranging manner. A condensed version of the project conclusions and recommendations is provided in Section 3. A list of the data sources and publications resulting from project work can be found at the end of the report

  11. Macular Choroidal Small-Vessel Layer, Sattler's Layer and Haller's Layer Thicknesses: The Beijing Eye Study.

    Science.gov (United States)

    Zhao, Jing; Wang, Ya Xing; Zhang, Qi; Wei, Wen Bin; Xu, Liang; Jonas, Jost B

    2018-03-13

    To study macular choroidal layer thickness, 3187 study participants from the population-based Beijing Eye Study underwent spectral-domain optical coherence tomography with enhanced depth imaging for thickness measurements of the macular small-vessel layer, including the choriocapillaris, medium-sized choroidal vessel layer (Sattler's layer) and large choroidal vessel layer (Haller's layer). In multivariate analysis, greater thickness of all three choroidal layers was associated (all P  0.05) associated with the prevalence of open-angle glaucoma or diabetic retinopathy. There was a tendency (0.07 > P > 0.02) toward thinner choroidal layers in chronic angle-closure glaucoma. The ratio of small-vessel layer thickness to total choroidal thickness increased (P layer and Haller's layer thickness to total choroidal thickness decreased. A higher ratio of small-vessel layer thickness to total choroidal thickness was significantly associated with a lower prevalence of AMD (early type, intermediate type, late geographic type). Axial elongation-associated and aging-associated choroidal thinning affected Haller's and Sattler's layers more markedly than the small-vessel layer. Non-exudative and exudative AMD, except for geographic atrophy, was associated with slightly increased choroidal thickness.

  12. Protecting the ozone layer.

    Science.gov (United States)

    Munasinghe, M; King, K

    1992-06-01

    Stratospheric ozone layer depletion has been recognized as a problem by the Vienna Convention for the Protection of the Ozone Layer and the 1987 Montreal Protocol (MP). The ozone layer shields the earth from harmful ultraviolet radiation (UV-B), which is more pronounced at the poles and around the equator. Industrialized countries have contributed significantly to the problem by releasing chlorofluorocarbons (CFCs) and halons into the atmosphere. The effect of these chemicals, which were known for their inertness, nonflammability, and nontoxicity, was discovered in 1874. Action to deal with the effects of CFCs and halons was initiated in 1985 in a 49-nation UN meeting. 21 nations signed a protocol limiting ozone depleting substances (ODS): CFCs and halons. Schedules were set based on each country's use in 1986; the target phaseout was set for the year 2000. The MP restricts trade in ODSs and weights the impact of substances to reflect the extent of damage; i.e., halons are 10 times more damaging than CFCs. ODS requirements for developing countries were eased to accommodate scarce resources and the small fraction of ODS emissions. An Interim Multilateral Fund under the Montreal Protocol (IMFMP) was established to provide loans to finance the costs to developing countries in meeting global environmental requirements. The IMFMP is administered by the World Bank, the UN Environmental Program, and the UN Development Program. Financing is available to eligible countries who use .3 kg of ODS/person/year. Rapid phaseout in developed countries has occurred due to strong support from industry and a lower than expected cost. Although there are clear advantages to rapid phaseout, there were no incentives included in the MP for rapid phaseout. Some of the difficulties occur because the schedules set minimum targets at the lowest possible cost. Also, costs cannot be minimized by a country-specific and ODS-specific process. The ways to improve implementation in scheduling and

  13. Derivation of Huntington Disease affected Genea046 human embryonic stem cell line

    Directory of Open Access Journals (Sweden)

    Biljana Dumevska

    2016-03-01

    Full Text Available The Genea046 human embryonic stem cell line was derived from a donated, fully commercially consented ART blastocyst, carrying HTT gene CAG expansion of 45 repeats, indicative of Huntington Disease. Following ICM outgrowth on inactivated human feeders, karyotype was confirmed as 46, XX by CGH and STR analysis demonstrated a female Allele pattern. The hESC line had pluripotent cell morphology, 85% of cells expressed Nanog, 92% Oct4, 75% Tra1–60 and 99% SSEA4 and demonstrated Alkaline Phosphatase activity. The cell line was negative for Mycoplasma and visible contamination.

  14. Friedel Transition in Layered Superconductors

    International Nuclear Information System (INIS)

    Dzierzawa, M.; Zamora, M.; Baeriswyl, D.; Bagnoud, X.

    1996-01-01

    Weakly coupled superconducting layers are described by the anisotropic 3D XY model. A low-temperature layer decoupling due to a proliferation of fluxons between planes, as proposed by Friedel, does not occur. The same is true for a periodic superlattice of high and low T c layers, although the interplane coherence can become extremely weak. On the other hand a true layer decoupling is found for a random stack. copyright 1996 The American Physical Society

  15. Cooperating systems: Layered MAS

    Science.gov (United States)

    Rochowiak, Daniel

    1990-01-01

    Distributed intelligent systems can be distinguished by the models that they use. The model developed focuses on layered multiagent system conceived of as a bureaucracy in which a distributed data base serves as a central means of communication. The various generic bureaus of such a system is described and a basic vocabulary for such systems is presented. In presenting the bureaus and vocabularies, special attention is given to the sorts of reasonings that are appropriate. A bureaucratic model has a hierarchy of master system and work group that organizes E agents and B agents. The master system provides the administrative services and support facilities for the work groups.

  16. Layered double hydroxides

    DEFF Research Database (Denmark)

    López Rayo, Sandra; Imran, Ahmad; Hansen, Hans Chr. Bruun

    2017-01-01

    A novel zinc (Zn) fertilizer concept based on Zn doped layered double hydroxides (Zn-doped Mg-Fe-LDHs) has been investigated. Zn-doped Mg-Fe-LDHs were synthetized, their chemical composition was analyzed and their nutrient release was studied in buffered solutions with different pH values. Uptake...... equation showing maximum release at pH 5.2, reaching approximately 45% of the total Zn content. The Zn concentrations in the plants receiving the LDHs were between 2- and 9.5-fold higher than those in plants without Zn addition. A positive effect of the LDHs was also found in soil. This work documents...

  17. The Keck keyword layer

    Science.gov (United States)

    Conrad, A. R.; Lupton, W. F.

    1992-01-01

    Each Keck instrument presents a consistent software view to the user interface programmer. The view consists of a small library of functions, which are identical for all instruments, and a large set of keywords, that vary from instrument to instrument. All knowledge of the underlying task structure is hidden from the application programmer by the keyword layer. Image capture software uses the same function library to collect data for the image header. Because the image capture software and the instrument control software are built on top of the same keyword layer, a given observation can be 'replayed' by extracting keyword-value pairs from the image header and passing them back to the control system. The keyword layer features non-blocking as well as blocking I/O. A non-blocking keyword write operation (such as setting a filter position) specifies a callback to be invoked when the operation is complete. A non-blocking keyword read operation specifies a callback to be invoked whenever the keyword changes state. The keyword-callback style meshes well with the widget-callback style commonly used in X window programs. The first keyword library was built for the two Keck optical instruments. More recently, keyword libraries have been developed for the infrared instruments and for telescope control. Although the underlying mechanisms used for inter-process communication by each of these systems vary widely (Lick MUSIC, Sun RPC, and direct socket I/O, respectively), a basic user interface has been written that can be used with any of these systems. Since the keyword libraries are bound to user interface programs dynamically at run time, only a single set of user interface executables is needed. For example, the same program, 'xshow', can be used to display continuously the telescope's position, the time left in an instrument's exposure, or both values simultaneously. Less generic tools that operate on specific keywords, for example an X display that controls optical

  18. Basis reduction for layered lattices

    NARCIS (Netherlands)

    Torreão Dassen, Erwin

    2011-01-01

    We develop the theory of layered Euclidean spaces and layered lattices. We present algorithms to compute both Gram-Schmidt and reduced bases in this generalized setting. A layered lattice can be seen as lattices where certain directions have infinite weight. It can also be

  19. Basis reduction for layered lattices

    NARCIS (Netherlands)

    E.L. Torreão Dassen (Erwin)

    2011-01-01

    htmlabstractWe develop the theory of layered Euclidean spaces and layered lattices. With this new theory certain problems that usually are solved by using classical lattices with a "weighting" gain a new, more natural form. Using the layered lattice basis reduction algorithms introduced here these

  20. The Atmospheric Boundary Layer

    Science.gov (United States)

    Garratt, J. R.

    1994-05-01

    A comprehensive and lucid account of the physics and dynamics of the lowest one to two kilometers of the Earth's atmosphere in direct contact with the Earth's surface, known as the atmospheric boundary layer (ABL). Dr. Garratt emphasizes the application of the ABL problems to numerical modeling of the climate, which makes this book unique among recent texts on the subject. He begins with a brief introduction to the ABL before leading to the development of mean and turbulence equations and the many scaling laws and theories that are the cornerstone of any serious ABL treatment. Modeling of the ABL is crucially dependent for its realism on the surface boundary conditions, so chapters four and five deal with aerodynamic and energy considerations, with attention given to both dry and wet land surfaces and the sea. The author next treats the structure of the clear-sky, thermally stratified ABL, including the convective and stable cases over homogeneous land, the marine ABL, and the internal boundary layer at the coastline. Chapter seven then extends this discussion to the cloudy ABL. This is particularly relevant to current research because the extensive stratocumulus regions over the subtropical oceans and stratus regions over the Arctic have been identified as key players in the climate system. In the final chapters, Dr. Garratt summarizes the book's material by discussing appropriate ABL and surface parameterization schemes in general circulation models of the atmosphere that are being used for climate stimulation.

  1. Air Layer Drag Reduction

    Science.gov (United States)

    Ceccio, Steven; Elbing, Brian; Winkel, Eric; Dowling, David; Perlin, Marc

    2008-11-01

    A set of experiments have been conducted at the US Navy's Large Cavitation Channel to investigate skin-friction drag reduction with the injection of air into a high Reynolds number turbulent boundary layer. Testing was performed on a 12.9 m long flat-plate test model with the surface hydraulically smooth and fully rough at downstream-distance-based Reynolds numbers to 220 million and at speeds to 20 m/s. Local skin-friction, near-wall bulk void fraction, and near-wall bubble imaging were monitored along the length of the model. The instrument suite was used to access the requirements necessary to achieve air layer drag reduction (ALDR). Injection of air over a wide range of air fluxes showed that three drag reduction regimes exist when injecting air; (1) bubble drag reduction that has poor downstream persistence, (2) a transitional regime with a steep rise in drag reduction, and (3) ALDR regime where the drag reduction plateaus at 90% ± 10% over the entire model length with large void fractions in the near-wall region. These investigations revealed several requirements for ALDR including; sufficient volumetric air fluxes that increase approximately with the square of the free-stream speed, slightly higher air fluxes are needed when the surface tension is reduced, higher air fluxes are required for rough surfaces, and the formation of ALDR is sensitive to the inlet condition.

  2. The Adobe Photoshop layers book

    CERN Document Server

    Lynch, Richard

    2011-01-01

    Layers are the building blocks for working in Photoshop. With the correct use of the Layers Tool, you can edit individual components of your images nondestructively to ensure that your end result is a combination of the best parts of your work. Despite how important it is for successful Photoshop work, the Layers Tool is one of the most often misused and misunderstood features within this powerful software program. This book will show you absolutely everything you need to know to work with layers, including how to use masks, blending, modes and layer management. You'll learn professional tech

  3. Buried oxide layer in silicon

    Science.gov (United States)

    Sadana, Devendra Kumar; Holland, Orin Wayne

    2001-01-01

    A process for forming Silicon-On-Insulator is described incorporating the steps of ion implantation of oxygen into a silicon substrate at elevated temperature, ion implanting oxygen at a temperature below 200.degree. C. at a lower dose to form an amorphous silicon layer, and annealing steps to form a mixture of defective single crystal silicon and polycrystalline silicon or polycrystalline silicon alone and then silicon oxide from the amorphous silicon layer to form a continuous silicon oxide layer below the surface of the silicon substrate to provide an isolated superficial layer of silicon. The invention overcomes the problem of buried isolated islands of silicon oxide forming a discontinuous buried oxide layer.

  4. Layered Ultrathin Coherent Structures (LUCS)

    International Nuclear Information System (INIS)

    Schuller, I.K.; Falco, C.M.

    1979-01-01

    A new class of superconducting materials, Layered Ultrathin Coherent Structures (LUCS) are described. These materials are produced by sequentially depositing ultrathin layers of materials using high rate magnetron sputtering or thermal evaporation. Strong evidence is presented that layers as thin as 10 A can be prepared in this fashion. Resistivity data indicates that the mean free path is layer thickness limited. A strong disagreement is found between the experimentally measured transition temperatures T/sub c/ and the T/sub c/'s calculated using the Cooper limit approximation. This is interpreted as a change in the band structure or the phonon structure of the material due to layering or to surfaces

  5. Analysis of turbulent boundary layers

    CERN Document Server

    Cebeci, Tuncer

    1974-01-01

    Analysis of Turbulent Boundary Layers focuses on turbulent flows meeting the requirements for the boundary-layer or thin-shear-layer approximations. Its approach is devising relatively fundamental, and often subtle, empirical engineering correlations, which are then introduced into various forms of describing equations for final solution. After introducing the topic on turbulence, the book examines the conservation equations for compressible turbulent flows, boundary-layer equations, and general behavior of turbulent boundary layers. The latter chapters describe the CS method for calculati

  6. An automated approach for annual layer counting in ice cores

    Science.gov (United States)

    Winstrup, M.; Svensson, A.; Rasmussen, S. O.; Winther, O.; Steig, E.; Axelrod, A.

    2012-04-01

    The temporal resolution of some ice cores is sufficient to preserve seasonal information in the ice core record. In such cases, annual layer counting represents one of the most accurate methods to produce a chronology for the core. Yet, manual layer counting is a tedious and sometimes ambiguous job. As reliable layer recognition becomes more difficult, a manual approach increasingly relies on human interpretation of the available data. Thus, much may be gained by an automated and therefore objective approach for annual layer identification in ice cores. We have developed a novel method for automated annual layer counting in ice cores, which relies on Bayesian statistics. It uses algorithms from the statistical framework of Hidden Markov Models (HMM), originally developed for use in machine speech recognition. The strength of this layer detection algorithm lies in the way it is able to imitate the manual procedures for annual layer counting, while being based on purely objective criteria for annual layer identification. With this methodology, it is possible to determine the most likely position of multiple layer boundaries in an entire section of ice core data at once. It provides a probabilistic uncertainty estimate of the resulting layer count, hence ensuring a proper treatment of ambiguous layer boundaries in the data. Furthermore multiple data series can be incorporated to be used at once, hence allowing for a full multi-parameter annual layer counting method similar to a manual approach. In this study, the automated layer counting algorithm has been applied to data from the NGRIP ice core, Greenland. The NGRIP ice core has very high temporal resolution with depth, and hence the potential to be dated by annual layer counting far back in time. In previous studies [Andersen et al., 2006; Svensson et al., 2008], manual layer counting has been carried out back to 60 kyr BP. A comparison between the counted annual layers based on the two approaches will be presented

  7. Generation and periodontal differentiation of human gingival fibroblasts-derived integration-free induced pluripotent stem cells

    Energy Technology Data Exchange (ETDEWEB)

    Yin, Xiaohui [Department of Periodontology, School and Hospital of Stomatology, Peking University, 22 South Avenue Zhong-Guan-Cun, Beijing 100081 (China); Peking University Stem Cell Research Center and Department of Cell Biology, School of Basic Medical Sciences, Peking University, 38 Xueyuan Road, Beijing 100191 (China); Li, Yang [Peking University Stem Cell Research Center and Department of Cell Biology, School of Basic Medical Sciences, Peking University, 38 Xueyuan Road, Beijing 100191 (China); Li, Jingwen [Department of Periodontology, School and Hospital of Stomatology, Peking University, 22 South Avenue Zhong-Guan-Cun, Beijing 100081 (China); Li, Peng [Faculty of Dentistry, The University of Hong Kong, 34 Hospital Road, Hong Kong SAR (China); Liu, Yinan [Peking University Stem Cell Research Center and Department of Cell Biology, School of Basic Medical Sciences, Peking University, 38 Xueyuan Road, Beijing 100191 (China); Wen, Jinhua, E-mail: jhwen@bjmu.edu.cn [Peking University Stem Cell Research Center and Department of Cell Biology, School of Basic Medical Sciences, Peking University, 38 Xueyuan Road, Beijing 100191 (China); Luan, Qingxian, E-mail: kqluanqx@126.com [Department of Periodontology, School and Hospital of Stomatology, Peking University, 22 South Avenue Zhong-Guan-Cun, Beijing 100081 (China)

    2016-05-06

    Induced pluripotent stem cells (iPSCs) have been recognized as a promising cell source for periodontal tissue regeneration. However, the conventional virus-based reprogramming approach is associated with a high risk of genetic mutation and limits their therapeutic utility. Here, we successfully generated iPSCs from readily accessible human gingival fibroblasts (hGFs) through an integration-free and feeder-free approach via delivery of reprogramming factors of Oct4, Sox2, Klf4, L-myc, Lin28 and TP53 shRNA with episomal plasmid vectors. The iPSCs presented similar morphology and proliferation characteristics as embryonic stem cells (ESCs), and expressed pluripotent markers including Oct4, Tra181, Nanog and SSEA-4. Additionally, these cells maintained a normal karyotype and showed decreased CpG methylation ratio in the promoter regions of Oct4 and Nanog. In vivo teratoma formation assay revealed the development of tissues representative of three germ layers, confirming the acquisition of pluripotency. Furthermore, treatment of the iPSCs in vitro with enamel matrix derivative (EMD) or growth/differentiation factor-5 (GDF-5) significantly up-regulated the expression of periodontal tissue markers associated with bone, periodontal ligament and cementum respectively. Taken together, our data demonstrate that hGFs are a valuable cell source for generating integration-free iPSCs, which could be sequentially induced toward periodontal cells under the treatment of EMD and GDF-5. - Highlights: • Integration-free iPSCs are successfully generated from hGFs via an episomal approach. • EMD promotes differentiation of the hGFs-derived iPSCs toward periodontal cells. • GDF-5 promotes differentiation of the hGFs-derived iPSCs toward periodontal cells. • hGFs-derived iPSCs could be a promising cell source for periodontal regeneration.

  8. Generation and periodontal differentiation of human gingival fibroblasts-derived integration-free induced pluripotent stem cells

    International Nuclear Information System (INIS)

    Yin, Xiaohui; Li, Yang; Li, Jingwen; Li, Peng; Liu, Yinan; Wen, Jinhua; Luan, Qingxian

    2016-01-01

    Induced pluripotent stem cells (iPSCs) have been recognized as a promising cell source for periodontal tissue regeneration. However, the conventional virus-based reprogramming approach is associated with a high risk of genetic mutation and limits their therapeutic utility. Here, we successfully generated iPSCs from readily accessible human gingival fibroblasts (hGFs) through an integration-free and feeder-free approach via delivery of reprogramming factors of Oct4, Sox2, Klf4, L-myc, Lin28 and TP53 shRNA with episomal plasmid vectors. The iPSCs presented similar morphology and proliferation characteristics as embryonic stem cells (ESCs), and expressed pluripotent markers including Oct4, Tra181, Nanog and SSEA-4. Additionally, these cells maintained a normal karyotype and showed decreased CpG methylation ratio in the promoter regions of Oct4 and Nanog. In vivo teratoma formation assay revealed the development of tissues representative of three germ layers, confirming the acquisition of pluripotency. Furthermore, treatment of the iPSCs in vitro with enamel matrix derivative (EMD) or growth/differentiation factor-5 (GDF-5) significantly up-regulated the expression of periodontal tissue markers associated with bone, periodontal ligament and cementum respectively. Taken together, our data demonstrate that hGFs are a valuable cell source for generating integration-free iPSCs, which could be sequentially induced toward periodontal cells under the treatment of EMD and GDF-5. - Highlights: • Integration-free iPSCs are successfully generated from hGFs via an episomal approach. • EMD promotes differentiation of the hGFs-derived iPSCs toward periodontal cells. • GDF-5 promotes differentiation of the hGFs-derived iPSCs toward periodontal cells. • hGFs-derived iPSCs could be a promising cell source for periodontal regeneration.

  9. miR-200c and GATA binding protein 4 regulate human embryonic stem cell renewal and differentiation

    Directory of Open Access Journals (Sweden)

    Hsiao-Ning Huang

    2014-03-01

    Full Text Available Human embryonic stem cells (hESCs are functionally unique for their self-renewal ability and pluripotency, but the molecular mechanisms giving rise to these properties are not fully understood. hESCs can differentiate into embryoid bodies (EBs containing ectoderm, mesoderm, and endoderm. In the miR-200 family, miR-200c was especially enriched in undifferentiated hESCs and significantly downregulated in EBs. The knockdown of the miR-200c in hESCs downregulated Nanog expression, upregulated GATA binding protein 4 (GATA4 expression, and induced hESC apoptosis. The knockdown of GATA4 rescued hESC apoptosis induced by downregulation of miR-200c. miR-200c directly targeted the 3′-untranslated region of GATA4. Interestingly, the downregulation of GATA4 significantly inhibited EB formation in hESCs. Overexpression of miR-200c inhibited EB formation and repressed the expression of ectoderm, endoderm, and mesoderm markers, which could partially be rescued by ectopic expression of GATA4. Fibroblast growth factor (FGF and activin A/nodal can sustain hESC renewal in the absence of feeder layer. Inhibition of transforming growth factor-β (TGF-β/activin A/nodal signaling by SB431542 treatment downregulated the expression of miR-200c. Overexpression of miR-200c partially rescued the expression of Nanog/phospho-Smad2 that was downregulated by SB431542 treatment. Our observations have uncovered novel functions of miR-200c and GATA4 in regulating hESC renewal and differentiation.

  10. Implementation of the Thin Layer Agar Method for Diagnosis of Smear-Negative Pulmonary Tuberculosis in a Setting with a High Prevalence of Human Immunodeficiency Virus Infection in Homa Bay, Kenya▿ †

    Science.gov (United States)

    Martin, Anandi; Munga Waweru, Peter; Babu Okatch, Fred; Amondi Ouma, Naureen; Bonte, Laurence; Varaine, Francis; Portaels, Françoise

    2009-01-01

    The objective of this study was to evaluate the performance of a low-cost method, the thin layer agar (TLA) method, for the diagnosis of smear-negative patients. This prospective study was performed in Homa Bay District Hospital in Kenya. Out of 1,584 smear-negative sputum samples, 212 (13.5%) were positive by culture in Löwenstein-Jensen medium (LJ) and 220 (14%) were positive by the TLA method. The sensitivities of LJ and TLA were 71% and 74%, respectively. TLA could become an affordable method for the diagnosis of smear-negative tuberculosis in resource-limited settings, with results available within 2 weeks. PMID:19494065

  11. Clustering network layers with the strata multilayer stochastic block model.

    Science.gov (United States)

    Stanley, Natalie; Shai, Saray; Taylor, Dane; Mucha, Peter J

    2016-01-01

    Multilayer networks are a useful data structure for simultaneously capturing multiple types of relationships between a set of nodes. In such networks, each relational definition gives rise to a layer. While each layer provides its own set of information, community structure across layers can be collectively utilized to discover and quantify underlying relational patterns between nodes. To concisely extract information from a multilayer network, we propose to identify and combine sets of layers with meaningful similarities in community structure. In this paper, we describe the "strata multilayer stochastic block model" (sMLSBM), a probabilistic model for multilayer community structure. The central extension of the model is that there exist groups of layers, called "strata", which are defined such that all layers in a given stratum have community structure described by a common stochastic block model (SBM). That is, layers in a stratum exhibit similar node-to-community assignments and SBM probability parameters. Fitting the sMLSBM to a multilayer network provides a joint clustering that yields node-to-community and layer-to-stratum assignments, which cooperatively aid one another during inference. We describe an algorithm for separating layers into their appropriate strata and an inference technique for estimating the SBM parameters for each stratum. We demonstrate our method using synthetic networks and a multilayer network inferred from data collected in the Human Microbiome Project.

  12. Características de las fallas en alimentadores de 13,8 kV del sistema soterrado de La Habana;Characteristic of 13,8 kV feeders faults of the Havana underground system

    Directory of Open Access Journals (Sweden)

    Boris Alba - Valle

    2011-06-01

    Full Text Available El sistema soterrado de La Habana enfrenta problemas de continuas fallas en sus alimentadores de 13,8 kV. En este trabajo se determinan las características de estas averías, en el período comprendido entre los años 2007 y 2009, y se proponen algunas medidas objetivas con el fin de contribuir a su disminución. La investigación se basó fundamentalmente en el estudio de la base de datos de los alimentadores de 13,8 kV proporcionada por el departamento técnico de la Unidad Empresarial Básica (UEB Soterrada y en el uso de herramientas estadísticas digitales. Como resultado se pudo constatar que las fallas son más frecuentes en los alimentadores de la subestación de Tallapiedra producto de la humedad en cables y empalmes con aislamiento de PILC (papel impregnado en aceite y con cubierta de plomo, dispuestos por tierra muerta. Finalmente, las medidas propuestas tuvieron un impacto positivo en la disminución de estas fallas, en un período inferior a un año.The Havana underground system has problems of continuous faults in their 13,8 kV feeders. In this article the characteristics of these mishaps in the period of 2007 to 2009 are determined and purpose some objective measurements with the end of contributing to their decrease. The investigation was fundamentally based on the study of the 13,8 kV feeders database proportioned by the technical department of the Underground Basic Managerial Unit (UEB and the use of digital statistical tools. As a result, it was verified that the faults occur with more frequency in the Tallapiedra substation feeders, due to the humidity in cables and connections with PILC isolation (impregnated in oil and lead covered paper, prepared for undergrounding directly in the earth. Finally, the proposed measures had a positive impact in the decrease of these faults, in a period less than to a year.

  13. A review of human cell radiosensitivity in vitro

    International Nuclear Information System (INIS)

    Deschavanne, Patrick J.; Fertil, Bernard

    1996-01-01

    The survival curves of 694 human cell lines irradiated in exponentially growing phase in vitro were collected from the literature. Among them, 271 were derived from tumors, 423 were nontransformed fibroblasts and other normal cell strains from healthy people or people with some genetic disorders. Seventy-six different cell types are identified, and a specific radiosensitivity could be associated with each, using D-bar and surviving fraction at 2 Gy. Technical factors such as culture medium, feeder cells, and scoring method were found to affect intrinsic radiosensitivity. In particular, the cell type is not a discriminating factor when cells are studied in agar. Results obtained with cells irradiated in agar must be used cautiously, depending on how the cells were prepared for the experiments. The use of feeder cells narrows the range of radiosensitivity of human cells. For cells irradiated as monolayer, it was possible to build a scale of radiosensitivity according to cell type, ranging, in terms of D-bar from 0.6 Gy for the most sensitive cell lines to more than 4 Gy for the most resistant. Considering that, in most cases, we could estimate the variation of radiosensitivity within each cell type, our classification among cell types can be used by researchers to place their results in the context of the literature

  14. Curvilinear crack layer propagation

    Science.gov (United States)

    Chudnovsky, Alexander; Chaoui, Kamel; Moet, Abdelsamie

    1987-01-01

    An account is given of an experiment designed to allow observation of the effect of damage orientation on the direction of crack growth in the case of crack layer propagation, using polystyrene as the model material. The direction of crack advance under a given loading condition is noted to be determined by a competition between the tendency of the crack to maintain its current direction and the tendency to follow the orientation of the crazes at its tip. The orientation of the crazes is, on the other hand, determined by the stress field due to the interaction of the crack, the crazes, and the hole. The changes in craze rotation relative to the crack define the active zone rotation.

  15. The layers of subtitling

    Directory of Open Access Journals (Sweden)

    Elena Di Giovanni

    2016-12-01

    Full Text Available The study of subtitling, although widely practiced over the past 20 years, has generally been confined to comparative studies focusing on the product of subtitle translation, with little or no consideration of the conditions of creation and reception. Focusing on the process of subtitle production, occasional studies have touched upon the cognitive processes accompanying it, but no study so far has related these processes, and the resulting products, to various degrees of translators’ competence. This is precisely what this essay does, focusing on the different layers of subtitle translation provided for two different films and in two different contexts. By analysing the first and second versions of subtitle translations, we shall reflect on the acquisition, and application, of different subtitling competences.

  16. Wireless physical layer security

    Science.gov (United States)

    Poor, H. Vincent; Schaefer, Rafael F.

    2017-01-01

    Security in wireless networks has traditionally been considered to be an issue to be addressed separately from the physical radio transmission aspects of wireless systems. However, with the emergence of new networking architectures that are not amenable to traditional methods of secure communication such as data encryption, there has been an increase in interest in the potential of the physical properties of the radio channel itself to provide communications security. Information theory provides a natural framework for the study of this issue, and there has been considerable recent research devoted to using this framework to develop a greater understanding of the fundamental ability of the so-called physical layer to provide security in wireless networks. Moreover, this approach is also suggestive in many cases of coding techniques that can approach fundamental limits in practice and of techniques for other security tasks such as authentication. This paper provides an overview of these developments.

  17. Multiple Temporalities, Layered Histories

    Directory of Open Access Journals (Sweden)

    Steven Pearson

    2017-11-01

    Full Text Available In Quotational Practices: Repeating the Future in Contemporary Art, Patrick Greaney asserts, “the past matters not only because of what actually happened but also because of the possibilities that were not realized and that still could be. Quotation evokes those possibilities. By repeating the past, artists and writers may be attempting to repeat that past’s unrealized futures.”[1]  In the information age, the Internet, for instance, provides us an expanded collection of visual information—quite literally available at our fingertips—summoning together aspects of the past and possibilities of the future into a boundless present. Sketchbook Revisions (2014–2015, a series of mixed-media paintings, represents my attempt to communicate the ways in which I experience my contemporary moment constructed from multiple temporalities excavated from my past. This body of work combines fragments of representational paintings created between 1995 and 2003 and nonrepresentational renderings produced between 2003 and 2014. Using traditional tracing paper and graphic color, I randomly select moments of my previous work to transfer and layer over selected a