Corrosion behaviour of hot dip zinc and zinc-aluminium coatings

Indian Academy of Sciences (India)

A comparative investigation of hot dip Zn–25Al alloy, Zn–55Al–Si and Zn coatings on steel was performed with attention to their corrosion performance in seawater. The results of 2-year exposure testing of these at Zhoushan test site are reported here. In tidal and immersion environments, Zn–25Al alloy coating is several ...

Effect of Al Hot-Dipping on High-Temperature Corrosion of Carbon Steel in N2/0.1% H2S Gas

Directory of Open Access Journals (Sweden)

Muhammad Ali Abro

2016-02-01

Full Text Available High-temperature corrosion of carbon steel in N2/0.1% H2S mixed gas at 600–800 °C for 50–100 h was studied after hot-dipping in the aluminum molten bath. Hot-dipping resulted in the formation of the Al topcoat and the Al-Fe alloy layer firmly adhered on the substrate. The Al-Fe alloy layer consisted primarily of a wide, tongue-like Al5Fe2 layer and narrow Al3Fe layer. When corroded at 800 °C for 100 h, the Al topcoat partially oxidized to the protective but non-adherent α-Al2O3 layer, and the interdiffusion converted the Al-Fe alloy layer to an (Al13Fe4, AlFe3-mixed layer. The interdiffusion also lowered the microhardness of the hot-dipped steel. The α-Al2O3 layer formed on the hot-dipped steel protected the carbon steel against corrosion. Without the Al hot-dipping, the carbon steel failed by forming a thick, fragile, and non-protective FeS scale.

Corrosion protection pays off for coal-fired power plants

Energy Technology Data Exchange (ETDEWEB)

Hansen, T.

2006-11-15

Zinc has long been used to hot-dip galvanise steel to deliver protection in harsh environments. Powder River Basin or eastern coal-fired plants benefit from using galvanized steel for conveyors, vibratory feeders, coal hoppers, chutes, etc. because maintenance costs are essentially eliminated. When life cycle costs for this process are compared to an alternative three-coal paint system for corrosion protection, the latter costs 5-10 times more than hot-dip galvanizing. An AEP Power Plant in San Juan, Puerto Rico and the McDuffie Coal Terminal in Mobile, AL, USA have both used hot-dip galvanized steel. 1 fig., 1 tab.

Corrosion behaviour of hot dip zinc and zinc–aluminium coatings on ...

Indian Academy of Sciences (India)

Abstract. A comparative investigation of hot dip Zn–25Al alloy, Zn–55Al–Si and Zn coatings on steel was performed with attention to their corrosion performance in seawater. The results of 2-year exposure testing of these at Zhoushan test site are reported here. In tidal and immersion environments, Zn–25Al alloy coating is.

Diversification of Intermetallic Zn Phases Growth on Steel During Hot-Dip Galvanizing

Directory of Open Access Journals (Sweden)

Węgrzynkiewicz S.

2016-06-01

Full Text Available The steel substrate formed as the result of oxy-acetylene cutting (OAB was treated differently - using: softening annealing, grinding and electro-polishing. Investigations were focused on the influence of additional processing on the structure and corrosion resistance of the deposited zinc coating. The hot - dip Zn galvanizing process was conducted in industrial conditions. Parameters were fixed: temperature 457 °C, dipping time 150 s. The coating thickness diversification dependent on the sub-surface steel structure was analysed and compared to the previous results. The correlation between conducted treatment and coatings morphology was determined.

Local strain energy density for the fatigue assessment of hot dip galvanized welded joints: some recent outcomes

Directory of Open Access Journals (Sweden)

M. Peron

2017-10-01

Full Text Available Since in literature only data about the effect of the hot-dip galvanizing coating on fatigue behavior of unnotched specimens are available, whereas very few for notched components and none for welded joints, the aim of this paper is to partially fill this lack of knowledge comparing fatigue strength of uncoated and hot-dip galvanized fillet welded cruciform joints made of structural steel S355 welded joints, subjected to a load cycle R = 0. 34. The results are shown in terms of stress range ?s and of the averaged strain energy density range DW in a control volume of radius R0 = 0.28 mm

Numerical Analysis of Edge Over Coating and Baffle Effect on Hot-Dip Galvanizing

Science.gov (United States)

Bao, Chengren; Kang, Yonglin; Li, Yan

2017-06-01

In hot-dip galvanizing process, air jet wiping control is so crucial to determine the coating thickness and uniformity of the zinc layer on the steel strip. A numerical simulation of gas-jet wiping in hot-dip galvanizing was conducted to minimize the occurrence of edge over coating (EOC). The causes of EOC were identified by contrasting and analyzing the airflow fields on the strip edge with and without a baffle. The factors influencing the airflow field on the strip edge during the change in the gap between the baffle and the strip edge were also analyzed. The effect of the distance between the air knife and the strip was evaluated. Technological parameters with on-site guidance role were obtained by combining them with the actual production to elucidate the role of the baffle in restraining the occurrence of EOC. The uniform distribution of pressure and coating thickness on the strip is achieved when the distance of the baffle from the strip edge is about 0.3 times of the jetting distance.

Effect of the Surface Layer of Iron Casting on the Growth of Protective Coating During Hot-Dip Galvanizing

Directory of Open Access Journals (Sweden)

Kopyciński D.

2016-03-01

Full Text Available The paper presents the results of investigations of the growth of protective coating on the surface of ductile iron casting during the hot-dip galvanizing treatment. Ductile iron of the EN-GJS-600-3 grade was melted and two moulds made by different technologies were poured to obtain castings with different surface roughness parameters. After the determination of surface roughness, the hot-dip galvanizing treatment was carried out. Based on the results of investigations, the effect of casting surface roughness on the kinetics of the zinc coating growth was evaluated. It was found that surface roughness exerts an important effect on the thickness of produced zinc coating.

Nanoscale surface analysis on second generation advanced high strength steel after hot dip galvanizing.

Science.gov (United States)

Arndt, M; Duchoslav, J; Preis, K; Samek, L; Stifter, D

2013-09-01

Second generation advanced high strength steel is one promising material of choice for modern automotive structural parts because of its outstanding maximal elongation and tensile strength. Nonetheless there is still a lack of corrosion protection for this material due to the fact that cost efficient hot dip galvanizing cannot be applied. The reason for the insufficient coatability with zinc is found in the segregation of manganese to the surface during annealing and the formation of manganese oxides prior coating. This work analyses the structure and chemical composition of the surface oxides on so called nano-TWIP (twinning induced plasticity) steel on the nanoscopic scale after hot dip galvanizing in a simulator with employed analytical methods comprising scanning Auger electron spectroscopy (SAES), energy dispersive X-ray spectroscopy (EDX), and focused ion beam (FIB) for cross section preparation. By the combination of these methods, it was possible to obtain detailed chemical images serving a better understanding which processes exactly occur on the surface of this novel kind of steel and how to promote in the future for this material system galvanic protection.

Effects of Niobium Microalloying on Microstructure and Properties of Hot-Dip Galvanized Sheet

Energy Technology Data Exchange (ETDEWEB)

Mohrbacher, Hardy [NiobelCon bvba, Brussels (Belgium)

2010-04-15

Niobium microalloying is effective in hot-rolled and cold-rolled steels by providing a fine-grained microstructure resulting in increased strength. To optimize the strengthening effect, alloy design and hot-rolling conditions have to be adapted. As a key issue the dissolution and precipitation characteristics of Nb are discussed in particular with regard to the run-out table conditions. It is then considered how the hot-rolled microstructure and the solute state of Nb interact with the hot-dip galvanizing cycle. The adjusted conditions allow controlling the morphology and distribution of phases in the cold-rolled annealed material. Additional precipitation hardening can be achieved as well. The derived options can be readily applied to produce conventional HSLA and IF high strength steels as well as to modem multiphase steels. It will be explained how important application properties such as strength, elongation, bendability, weldability and delayed cracking resistance can be influenced in a controlled and favorable way. Examples of practical relevance and experience are given.

Surface conditioning of a cold-rolled dual-phase steel by annealing in nitriding atmospheres prior to hot-dip galvanizing

Energy Technology Data Exchange (ETDEWEB)

Luther, F.; Beste, D.; Bleck, W. [Institute for Ferrous Metallurgy (IEHK), RWTH Aachen (Germany); Dimyati, A.; Mayer, J. [Central Facility for Electron Microscopy (GFE), RWTH Aachen (Germany)

2007-04-15

The development of steel grades for automotive applications in the recent years has been driven on by two trends: lightweight and improved crash safety. By using steels like DP (dual phase) the goals of passenger safety, fuel efficiency and environmental friendliness can be met at reasonable price. The favorite corrosion protection method for sheet steels in the car industry is the hot-dip galvanizing process. Here, an approach was made to reduce the surface enrichment of critical alloying elements of a dual phase steel grade by reactive annealing in ammonia containing atmospheres. The effects of this treatment on mechanical properties and hot-dip coating behavior are reported. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

Characterization of the behaviour of electro-galvanised steel sheets in terms of corrosion

International Nuclear Information System (INIS)

Finoly, Guylene

1992-01-01

This research thesis reports the development of a test method for the characterization of the behaviour of electro-galvanised steel sheets (i.e. zinc coated steel sheets as those used in the automotive industry) with respect to corrosion, and the definition of a classification of these materials with respect to their surface activity. After an overview of the different existing methods of determination of corrosion rate, the author reports the development of an experimental device adapted to the electrochemical study of electro-galvanised sheets, i.e. adapted to their low thickness (0,7 mm) and coating characteristics (10 μm thick). This device is then used in the case of solid zinc. The authors reports the study of the behaviour of sheets in a NaCl solution in order to meet industrial conditions used to activate the surface before the phosphate conversion process which aims at ensuring paint adherence. A test is proposed and validated by comparison with other electrochemical or chemical methods, and used to study the behaviour of electro-galvanised sheets submitted to a phosphate conversion coating process [fr

The influence of alloying elements on the hot-dip aluminizing process and on the subsequent high-temperature oxidation

International Nuclear Information System (INIS)

Glasbrenner, H.; Nold, E.; Voss, Z.

1997-01-01

For hot dip aluminizing HDA an Al melt was doped with one of the elements Mo, W or Nb with a nominal composition of about 1 wt%. In case of W, the nominal composition was achieved, not so for Mo and Nb. The influence of these elements on the coating formed and on the following oxidation process was investigated. Hot dip aluminizing was carried out at 800 C for 5 min under dry Ar atmosphere. The oxidation experiments were performed at 950 C for 24 h in air. Compared to the HDA processes with pure Al, the addition of the alloying elements lead to thinner intermetallic layers. A change in the oxidation behavior was observed as well concerning the suppression of internal oxidation and the formation of dense and close oxide scales. (orig.)

The morphology of coating/substrate interface in hot-dip-aluminized steels

International Nuclear Information System (INIS)

Awan, Gul Hameed; Hasan, Faiz ul

2008-01-01

In hot-dip-aluminized (HAD) steels, the morphology and the profile of the interface between the aluminum coating and the substrate steel, are affected both by the composition of the molten aluminum as well as by the composition, and even the microstructure, of the substrate steel. This effect has been investigated using optical and scanning electron microscopy, and X-ray diffraction. The reaction between the steel and the molten aluminum leads to the formation of Fe-Al inter-metallic compounds on the steel surface. The thickness of the inter-metallic compound layer as well as the morphology of the interface between the steel and the interlayer varies with the silicon content of the molten aluminum. In hot-dip-aluminizing with pure aluminum, the interlayer is 'thick' and exhibits a finger-like growth into the steel. With a gradually increasing addition of silicon into the aluminum melt, the thickness of the interlayer decreases while the interface between the interlayer and the substrate gradually becomes 'smoother'. With an increase in the carbon content of the substrate steel the growth of the interlayer into the steel is impeded by the pearlite phase, whereas the ferrite phase appears to dissolve more readily. X-ray diffraction and electron microscopic studies showed that the interlayer formed in samples aluminized in pure aluminum, essentially consisted of orthorhombic Fe 2 Al 5 . It was further observed that the finger-like grains of Fe 2 Al 5 phase exhibited a preferred lattice orientation. With a gradual addition of silicon into the aluminum melt, a cubic phase based on Fe 3 Al also started to form in the interlayer and replaced most of the Fe 2 Al 5

The effect of immersion time to low carbon steel hardness and microstructure with hot dip galvanizing coating method

Science.gov (United States)

Hakim, A. A.; Rajagukguk, T. O.; Sumardi, S.

2018-01-01

Along with developing necessities of metal materials, these rise demands of quality improvements and material protections especially the mechanical properties of the material. This research used hot dip galvanizing coating method. The objectives of this research were to find out Rockwell hardness (HRb), layer thickness, micro structure and observation with Scanning Electron Microscope (SEM) from result of coating by using Hot Dip Galvanizing coating method with immersion time of 3, 6, 9, and 12 minutes at 460°C. The result shows that Highest Rockwell hardness test (HRb) was at 3 minutes immersion time with 76.012 HRb. Highest thickness result was 217.3 μm at 12 minutes immersion. Microstructure test result showed that coating was formed at eta, zeta, delta and gamma phases, while Scanning Electron Microscope (SEM) showed Fe, Zn, Mn, Si and S elements at the specimens after coating.

Description of structure of Fe-Zn intermetalic compounds present in hot-dip galvanized coatings on steel

Directory of Open Access Journals (Sweden)

P. Pokorny

2015-10-01

Full Text Available The article is describing formation, composition, morphology and crystallographic characteristics of intermetalic compounds Fe - Zn present in the coating formed during the process of low-temperature hot-dip galvanizing of carbon steels. In mutual confrontation we introduce older bibliography and results of latest modern researches based on combination of most precise analytical methods.

Reduce of adherence problems in galvanised processes through data mining techniques

International Nuclear Information System (INIS)

Martinez de Pison, F. J.; Ordieres, J.; Pernia, A.; Alba, F.; Torre, V.

2007-01-01

This paper presents an example of the application of data mining techniques to obtain hidden knowledge from the historical data of a hot dip galvanizing process and to establish rules to improve quality in the final product and to reduce errors in the process. For this purpose, the tuning records of a hot dip galvanizing line where coils with adherence problems in the zinc coating had been identified were used as starting point. From the database of the process, the classical data mining approach was applied to obtain and analyze a number of decision trees hat classified two types of coils, i.e. those with the right adherence and those with irregular adherence. The variables and values that might have influenced the quality of the coating were extracted from these tress. Several rules that may be applied to reduce the number of faulty coils with adherence problems were also established. (Author) 24 refs

Designing the Color of Hot-Dip Galvanized Steel Sheet Through Destructive Light Interference Using a Zn-Ti Liquid Metallic Bath

Science.gov (United States)

Levai, Gabor; Godzsák, Melinda; Török, Tamas I.; Hakl, Jozsef; Takáts, Viktor; Csik, Attila; Vad, Kalman; Kaptay, George

2016-07-01

The color of hot-dip galvanized steel sheet was adjusted in a reproducible way using a liquid Zn-Ti metallic bath, air atmosphere, and controlling the bath temperature as the only experimental parameter. Coloring was found only for samples cooled in air and dipped into Ti-containing liquid Zn. For samples dipped into a 0.15 wt pct Ti-containing Zn bath, the color remained metallic (gray) below a 792 K (519 °C) bath temperature; it was yellow at 814 K ± 22 K (541 °C ± 22 °C), violet at 847 K ± 10 K (574 °C ± 10 °C), and blue at 873 K ± 15 K (600 °C ± 15 °C). With the increasing bath temperature, the thickness of the adhered Zn-Ti layer gradually decreased from 52 to 32 micrometers, while the thickness of the outer TiO2 layer gradually increased from 24 to 69 nm. Due to small Al contamination of the Zn bath, a thin (around 2 nm) alumina-rich layer is found between the outer TiO2 layer and the inner macroscopic Zn layer. It is proven that the color change was governed by the formation of thin outer TiO2 layer; different colors appear depending on the thickness of this layer, mostly due to the destructive interference of visible light on this transparent nano-layer. A complex model was built to explain the results using known relationships of chemical thermodynamics, adhesion, heat flow, kinetics of chemical reactions, diffusion, and optics. The complex model was able to reproduce the observations and allowed making predictions on the color of the hot-dip galvanized steel sample, as a function of the following experimental parameters: temperature and Ti content of the Zn bath, oxygen content, pressure, temperature and flow rate of the cooling gas, dimensions of the steel sheet, velocity of dipping the steel sheet into the Zn-Ti bath, residence time of the steel sheet within the bath, and the velocity of its removal from the bath. These relationships will be valuable for planning further experiments and technologies on color hot-dip galvanization of steel

Dip-slope and Dip-slope Failures in Taiwan - a Review

Science.gov (United States)

Lee, C.

2011-12-01

Taiwan is famous for dip-slope and dip-slope slides. Dip-slopes exist at many places in the fold-and-thrust belt of Taiwan. Under active cutting of stream channels and man-made excavations, a dip-slope may become unstable and susceptible for mass sliding. Daylight of a bedding parallel clay seam is the most dangerous type for dip-slope sliding. Buckling or shear-off features may also happen at toe of a long dip-slope. Besides, a dip-slope is also dangerous for shallow debris slides, if the slope angle is between 25 to 45 degrees and the debris (colluvium or slope wash) is thick (>1m). These unstable slopes may slide during a triggering event, earthquake or typhoon storm; or even slide without a triggering event, like the 2010 Tapu case. Initial buckling feature had been found in the dip-slope of the Feitsui arch dam abutment after detailed explorations. Shear-off feature have also been found in dip-slope located in right bank of the Nahua reservoir after field investigation and drilling. The Chiufengerhshan slide may also be shear-off type. On the other hand, the Tapu, the Tsaoling slides and others are of direct slide type. The Neihoo Bishan slide is a shallow debris slide on dip-slope. All these cases demonstrate the four different types of dip-slope slide. The hazard of a dip-slope should be investigated to cover these possible types of failure. The existence of bedding parallel clay seams is critical for the stability of a dip-slope, either for direct slide or buckling or shear-off type of failure, and is a hot point during investigation. Because, the stability of a dip-slope is changing with time, therefore, detailed explorations to including weathering and erosion rates are also very necessary to ensure the long-term stability of a dip-slope.

Nanoscale analysis of the influence of pre-oxidation on oxide formation and wetting behavior of hot-dip galvanized high strength steel

International Nuclear Information System (INIS)

Arndt, M.; Duchoslav, J.; Steinberger, R.; Hesser, G.; Commenda, C.; Samek, L.; Arenholz, E.

2015-01-01

Highlights: • Pre-oxidized hot-dip galvanized advanced high strength steel was examined. • The interface was analyzed in detail via high energy resolution Auger spectra. • Evidence for an aluminothermic reduction of the Mn oxide was found. • A new model for galvanizing high manganese steel was developed. - Abstract: Hot-dip galvanized (HDG) 2nd generation advanced high strength steel (AHSS), nano-TWIP (twinning induced plasticity) with 15.8 wt.% Mn, 0.79 wt.% C, was analyzed at the interface between steel and zinc by scanning Auger electron microscopy (AES) in order to confirm and improve an existing model of additional pre-oxidation treatment before annealing and immersion into the hot zinc bath. Furthermore these steel samples were fractured in the analysis chamber of the AES and analyzed without breaking vacuum. In these measurements the results of an aluminothermic reduction of the manganese and iron surface oxides on the steel could be confirmed by AES

Influence of hot water dip and gamma irradiation on postharvest fungal decay of Galia melons

International Nuclear Information System (INIS)

Barkai-Golan, R.; Padova, R.; Ross, I.; Lapidot, M.; Copel, A.; Davidson, H.

1993-01-01

Dipping Galia melons in hot water at 52 deg C for 5 min or at 55 deg for 2 min resulted in 12-15% decay (caused by Alternaria alternata, Fusarium spp. and Trichothecium roseum) during prolonged storage (12 d at 6 deg plus 3 d at 18 deg ) compared with 75% decay in untreated fruit or 60% decay in cold-water-dipped fruit. Irradiation at 0.5 or 1 kGy had no significant effect on decay development. However, combination of heat treatment with a 0.5 kGy dose prevented fungal growth, resulting in 5% decay during storage. Combinations of heating with 1 kGy irradiation gave no improvement in anti-fungal effect over treatment with 0.5 kGy and sometimes resulted in a decreased suppressive effect. Reducing the duration of dipping at 55 deg from 2 to 0.5 min, applied alone or in combination with irradiation, considerably reduced the anti-fungal effect of the treatment. The effective combined treatment resulted in 12-15% of slight peel damage, but all the fruits were regarded as marketable. No differences in fruit firmness were recorded among the treatments

Identification of Intermetallic Compounds and Its Formation Mechanism in Boron Steel Hot-Dipped in Al-7 wt.% Mn Alloy

Directory of Open Access Journals (Sweden)

Sung-Yun Kwak

2017-12-01

Full Text Available In laser welding and hot stamping Al-Si-coated boron steel, there is a problem that the strength of the joint is lowered due to ferrite formation in the fusion zone. The purpose of this study is to develop an Al-7 wt.% Mn hot-dip coating in which Mn, an austenite stabilizing element, replaces the ferrite stabilizing element Si. The nucleation and formation mechanism of the reaction layer was studied in detail by varying the dipping time between 0 and 120 s at 773 °C. The microstructure and phase constitution of the reaction layer were investigated by various observational methods. Phase formation is discussed using a phase diagram calculated by Thermo-CalcTM. Under a 30 s hot-dipping process, no reaction occurred due to the formation of a Fe3O4 layer on the steel surface. The Fe3O4 layer decomposed by a reduction reaction with Al-Mn molten alloy, constituent elements of steel dissolved into a liquid, and the reaction-layer nucleus was formed toward the liquid phase. A coated layer consists of a solidified layer of Al and Al6Mn and a reactive layer formed beneath it. The reaction layer is formed mainly by inter-diffusion of Al and Fe in the solid state, which is arranged on the steel in the order of Al11Mn4 → FeAl3 (θ → Fe2Al5 (η phases, and the Fe3AlC (κ in several nm bands formed at the interface between the η-phase and steel.

ENVIRONMENTAL AND ECONOMIC ASPECTS OF ANTICORROSION PROTECTION BY HOT-DIP GALVANIZED METHOD REBARS IN CONCRETE

Directory of Open Access Journals (Sweden)

Hegyi Andreea

2015-05-01

Full Text Available The implementation of the sustainable development concept is nowadays a key issue in almost all human activities. For the constructions domain an European strategy has already been elaborated. Among its goals are also the use of long lasting materials and the reduction of repair costs. This paper presents an interdisciplinary study concerning the efficiency of the use of hot-dip galvanized rebar for concrete structures. Experimental results about corrosion kinetics of coated and usual steel reinforcement embedded in concrete, subjected to chlorine ions attack, are analyzed. Electrochemical methods as chronoamperometry and linear polarization have been used. Corrosion potential values recorded for galvanized steel embedded in concrete indicate an uncertain corrosion activation process up to a rate of 2.5 % calcium chloride relative to concrete. For rates of 5% CaCl2 and more the corrosion process is activated. For unprotected steel bars embedded in concrete the corrosion activation process started at all calcium chloride studied rates and higher corrosion potential values has been registered than for the hot-dip galvanized ones, at the same rates. Economical assessments have been done using entire lifetime cost analysis of the reinforced concrete structures. Despite that the hotdip galvanization is a rather expansive procedure, when taking into account the whole expected life span, the use of zinc coating proves to be efficient both from structural and financial approaches.

The Effect of Fly Ash on the Corrosion Behaviour of Galvanised Steel Rebarsin Concrete

Science.gov (United States)

Tittarelli, Francesca; Mobili, Alessandra; Bellezze, Tiziano

2017-08-01

The effect of fly ash on the corrosion behaviour of galvanised steel rebars in cracked concrete specimens exposed to wet-dry cycles in a chloride solution has been investigated. The obtained results show that the use of fly ash, replacing either cement or aggregate, always improves the corrosion behaviour of galvanised steel reinforcements. In particular, the addition of fly ash, even in the presence of concrete cracks, decreases the corrosion rate monitored in very porous concretes, as those with w/c = 0.80, to values comparable with those obtained in good quality concretes, as those with w/c = 0.45. Therefore, fly ash cancels the negative effect, at least from the corrosion point of view, of a great porosity of the cement matrix.

Formation of Outburst Structure in Hot Dip Galvannealed Coatings on IF Steels

Directory of Open Access Journals (Sweden)

Kollárová, M.

2007-01-01

Full Text Available Outburst structure in two industrially produced hot dip galvanized interstitial free steel sheets for automotive industry after additional annealing has been examined. Ti IF steel was found to form weak outburst structure in the early stage of annealing, followed by frontal growth of Fe-Zn phases during further heating. The high reactivity of this steel was confirmed by rapid G-phase formation. Under the same conditions, Ti-Nb-P IF steel exhibited frontal growth of Fe-Zn compounds without G-phase formation due to relatively high phosphorous content, which is known as inhibitor of Fe-Zn reaction, but simultaneously significant occurrence of undesired outburst structures was recorded. It was assumed that the phosphorous content was insufficient and/or ferrite grain was very fine.

Thermodynamic Study of the Nickel Addition in Zinc Hot-Dip Galvanizing Baths

Science.gov (United States)

Pistofidis, N.; Vourlias, G.

2010-01-01

A usual practice during zinc hot-dip galvanizing is the addition of nickel in the liquid zinc which is used to inhibit the Sandelin effect. Its action is due to the fact that the ζ (zeta) phase of the Fe-Zn system is replaced by the Τ (tau) phase of the Fe-Zn-Ni system. In the present work an attempt is made to explain the formation of the Τ phase with thermodynamics. For this reason the Gibbs free energy changes for Τ and ζ phases were calculated. The excess free energy for the system was calculated with the Redlich-Kister polyonyme. From this calculation it was deduced that the Gibbs energy change for the tau phase is negative. As a result its formation is spontaneous.

Effect of Annealed Oxides on the Formation of Inhibition Layer During Hot-Dip Galvanizing of 590Mpa Trip Steel

International Nuclear Information System (INIS)

Kim, Seong Hwan; Huh, Joo Youl; Lee, Suk Kyu; Park, Rho Bum; Kim, Jong Sang

2011-01-01

The selective surface oxidation of a transformation-induced-plasticity (TRIP) steel containing 1.6 wt.% Mn and 1.5 wt.% Si during annealing at 800 .deg. C was investigated for its influence on the formation of an inhibition layer during hot-dip galvanizing. The selective oxidation of the alloying elements and the oxide morphology were significantly influenced by the annealing atmosphere. The pure N 2 atmosphere with a dew point -40 .deg. C promoted the selective oxidation of Mn as a crystalline Mn 2 SiO 4 phase, whereas the N 2 + 10% H 2 atmosphere with the same dew point -40 .deg. C promoted the selective oxidation of Si as an amorphous Si-rich oxide phase. During hot-dip galvanizing, the Mn 2 SiO 4 phase was reduced more readily by Al in the Zn bath than the Si-rich oxide phase. Consequently, the pure N 2 atmosphere resulted in a higher formation rate of Fe 2 Al 5 particles at the Zn/steel interface and better galvanizability than the N 2 + 10% H 2 atmosphere

Dissolution-Induced Nanowire Synthesis on Hot-Dip Galvanized Surface in Supercritical Carbon Dioxide

Directory of Open Access Journals (Sweden)

Aaretti Kaleva

2017-07-01

Full Text Available In this study, we demonstrate a rapid treatment method for producing a needle-like nanowire structure on a hot-dip galvanized sheet at a temperature of 50 °C. The processing method involved only supercritical carbon dioxide and water to induce a reaction on the zinc surface, which resulted in growth of zinc hydroxycarbonate nanowires into flower-like shapes. This artificial patina nanostructure predicts high surface area and offers interesting opportunities for its use in industrial high-end applications. The nanowires can significantly improve paint adhesion and promote electrochemical stability for organic coatings, or be converted to ZnO nanostructures by calcining to be used in various semiconductor applications.

Problems with reliability and safety of hot dip galvanized steel structures Problemas com a confiabilidade e segurança de estruturas de aço galvanizadas a quente

Directory of Open Access Journals (Sweden)

L. Mraz

2009-06-01

Full Text Available Hot dip galvanizing is very effective means of protection against corrosion. Some recommendation concerning the steel quality are generally known and accepted. The process consists of cleaning (pickling or sand blasting and dipping the structures or pieces into liquid zinc bath. The case study of hot dip galvanized steels is presented. Some recent failures of hot dip galvanized welded structures and hot dip galvanized high strength steel screws are presented. Structures were made of S355 grade steel and MIG/MAG process was applied for welding. Large cracks were observed in the vicinity of welds after hot dip galvanizing process. The presence of both hydrogen and liquid metal embrittlement was identified and associated mainly with higher hardness of HAZ or the quenched and tempered steels. Possible cracking mechanisms are discussed. The influence of chemical composition and production process (welding, heat treatment was analyzed according to data published in literature. The solutions and recommendations for avoiding the failure in hot dip galvanized structures are proposed.Galvanização a quente é um meio muito efetivo de proteção contra a corrosão. Recomendações relativas a qualidade do aço são geralmente conhecidas e aceitas. O processo consiste de limpar (decapagem ou jateamento e mergulhar as estruturas ou partes destas em um banho de zinco líquido. O presente trabalho apresenta casos de falhas recentes em estruturas soldadas e em parafusos de aços de alta resistência galvanizados a quente. As estruturas foram fabricadas com aço do grau S355 e o processo MIG/MAG foi usado para a soldagem. Os parafusos foram fabricados com aço de alto carbono. Grandes trincas foram observadas nas proximidades das soldas após o processo de galvanização a quente. A ocorrência de fragilização tanto por hidrogênio como por metal líquido foi identificada e associada com a dureza elevada tanto da ZTA como dos aços temperados e revenidos. Os

Application of thermodynamics and Wagner model on two problems in continuous hot-dip galvanizing

Science.gov (United States)

Liu, Huachu; He, Yanlin; Li, Lin

2009-12-01

Firstly in this paper, the influence of H 2 and water vapor content on selective oxidation occurred in continuous hot-dip galvanizing has been studied by thermodynamics and Wagner model, then, the Gibbs energy of each possible aluminothermic reducing reaction in zinc bath was calculated in order to judge the possibility of these reactions. It was found that oxides' amounts and oxidation type were greatly related to the H 2 and water content in the annealing atmosphere. And from the view of thermodynamics, surface oxides (MnO, Cr 2O 3, SiO 2 etc.) can be reduced by the effective Al in Zn bath.

Application of thermodynamics and Wagner model on two problems in continuous hot-dip galvanizing

Energy Technology Data Exchange (ETDEWEB)

Liu Huachu; He Yanlin [School of Material Science and Engineering, Shanghai University, No.149 Yanchang Road Shanghai 200072 (China); Li Lin, E-mail: liling@shu.edu.cn [School of Material Science and Engineering, Shanghai University, No.149 Yanchang Road Shanghai 200072 (China)

2009-12-15

Firstly in this paper, the influence of H{sub 2} and water vapor content on selective oxidation occurred in continuous hot-dip galvanizing has been studied by thermodynamics and Wagner model, then, the Gibbs energy of each possible aluminothermic reducing reaction in zinc bath was calculated in order to judge the possibility of these reactions. It was found that oxides' amounts and oxidation type were greatly related to the H{sub 2} and water content in the annealing atmosphere. And from the view of thermodynamics, surface oxides (MnO, Cr{sub 2}O{sub 3}, SiO{sub 2} etc.) can be reduced by the effective Al in Zn bath.

Effect of hot dip galvanization on the fatigue strength of steel bolted connections

Directory of Open Access Journals (Sweden)

S.M.J. Razavi

2017-07-01

Full Text Available Hot dip galvanized steel bolted joints has been tested under fatigue loading to evaluate the effect of galvanizing coating on the fatigue strength of S355 structural steel. The experimental results showed that the decrease of the fatigue life of coated specimens in comparison with that of uncoated joints is very limited and the results are in good agreement with Eurocode detail category, without substantial reductions. The procedure for coating and preparation of the bolted joints is described in detail in this paper providing a useful tool for engineers involved in similar practical applications. The experimental results are compared with the previously published data on central hole notched galvanized and not treated specimens characterized by the same geometry.

Effect of Annealed Oxides on the Formation of Inhibition Layer During Hot-Dip Galvanizing of 590Mpa Trip Steel

Energy Technology Data Exchange (ETDEWEB)

Kim, Seong Hwan; Huh, Joo Youl [Korea University, Seoul (Korea, Republic of); Lee, Suk Kyu; Park, Rho Bum; Kim, Jong Sang [POSCO Technical Research Laboratories, Gwangyang (Korea, Republic of)

2011-02-15

The selective surface oxidation of a transformation-induced-plasticity (TRIP) steel containing 1.6 wt.% Mn and 1.5 wt.% Si during annealing at 800 .deg. C was investigated for its influence on the formation of an inhibition layer during hot-dip galvanizing. The selective oxidation of the alloying elements and the oxide morphology were significantly influenced by the annealing atmosphere. The pure N{sub 2} atmosphere with a dew point -40 .deg. C promoted the selective oxidation of Mn as a crystalline Mn{sub 2}SiO{sub 4} phase, whereas the N{sub 2} + 10% H{sub 2} atmosphere with the same dew point -40 .deg. C promoted the selective oxidation of Si as an amorphous Si-rich oxide phase. During hot-dip galvanizing, the Mn{sub 2}SiO{sub 4} phase was reduced more readily by Al in the Zn bath than the Si-rich oxide phase. Consequently, the pure N{sub 2} atmosphere resulted in a higher formation rate of Fe{sub 2}Al{sub 5} particles at the Zn/steel interface and better galvanizability than the N{sub 2} + 10% H{sub 2} atmosphere.

Deformation and fatigue behavior of hot dip galvanized coatings

International Nuclear Information System (INIS)

Camurri, Carlos P.; Benavente, Raul G.; Roa, Isidoro S.; Carrasco, Claudia C.

2005-01-01

This paper reports on the results of a study of the effect of static and dynamic stresses on hot dip galvanized coatings on SAE 1020 steel substrates. Galvanizing was performed using baths maintained at 450 deg. C, the zinc containing 0.16% Ti and 0.02% Fe and with Al and Ni in the ranges 0-0.20% and 0-0.30%, respectively. Static three-point bend tests were conducted with applied stresses in the range 428-790 MPa. Dynamic bend-fatigue tests involved stresses in the range 228-578 MPa at a cyclic frequency of 0.25 Hz for up to 700 cycles. The total crack density in the coatings was measured before and after the tests using light optical and electron microscopy. The results showed that the crack density increased as the applied stress increased and crack propagation was promoted perpendicular to the substrate. The number of cycles had no effect on the crack density and propagation at stresses lower than 386 MPa. At higher stresses the number of applied cycles contributed only to crack propagation. It was concluded that the best bath composition for preventing fatigue crack propagation is one that minimized the formation of thinner brittle layers in the galvanized coatings

Effect of Dynamic Flow on the Structure of Inhibition Layer in Hot-dip Galvanizing

Energy Technology Data Exchange (ETDEWEB)

Jin, Young Sool; Kim, Myung Soo; Kim, Su Young [POSCO Technical Research Labs., Gwangyang (Korea, Republic of); Paik, Doo Jin [POSCO Kwangyang Steel Works, Gwangyang (Korea, Republic of)

2011-02-15

The effect of dynamic flow or forced convection were investigated and compared on the formation of inhibition layer, galvanizing and galvannealing reactions through the hot-dip galvanizing simulator with the oscillation of specimen in zinc bath, continuous galvanizing pilot plant with zinc pumping system through the snout and continuous galvanizing operation with Dynamic Galvanizing{sup TR} system. The interfacial Al pick-up was not consistent between the results of simulator, pilot plant and line operation, but the morphology of inhibition layer became compact and refined by the forced convection. The growth of Fe-Zn intermetallics at the interface was inhibited by the forced convection, whereas the galvannealing rate would be a little promoted.

An evaluation of airborne nickel, zinc, and lead exposure at hot dip galvanizing plants.

Science.gov (United States)

Verma, D K; Shaw, D S

1991-12-01

Industrial hygiene surveys were conducted at three hot dip galvanizing plants to determine occupational exposure to nickel, zinc, and lead. All three plants employed the "dry process" and used 2% nickel, by weight, in their zinc baths. A total of 32 personal and area air samples were taken. The air samples were analyzed for nickel, zinc, and lead. Some samples were also analyzed for various species of nickel (i.e., metallic, soluble, and oxidic). The airborne concentrations observed for nickel and its three species, zinc, and lead at the three plants were all well below the current and proposed threshold limit values recommended by the American Conference of Governmental Industrial Hygienists (ACGIH).

Effect of Dynamic Flow on the Structure of Inhibition Layer in Hot-dip Galvanizing

International Nuclear Information System (INIS)

Jin, Young Sool; Kim, Myung Soo; Kim, Su Young; Paik, Doo Jin

2011-01-01

The effect of dynamic flow or forced convection were investigated and compared on the formation of inhibition layer, galvanizing and galvannealing reactions through the hot-dip galvanizing simulator with the oscillation of specimen in zinc bath, continuous galvanizing pilot plant with zinc pumping system through the snout and continuous galvanizing operation with Dynamic Galvanizing TR system. The interfacial Al pick-up was not consistent between the results of simulator, pilot plant and line operation, but the morphology of inhibition layer became compact and refined by the forced convection. The growth of Fe-Zn intermetallics at the interface was inhibited by the forced convection, whereas the galvannealing rate would be a little promoted

Effect of Coating-thickness on the formability of hot dip aluminized steel

International Nuclear Information System (INIS)

Awan, G.H.; Ahmed, F.; Hasan, F.

2008-01-01

The influence of coating thickness on the formability and ductility of hot-dip-aluminized steel has been determined using a 3-point bend test and optical metallography. The ductility / formability was estimated from the 3-point bend test wherein the angle of bend at which the cracks start to appear on the surface of the aluminized sheet during bending, was taken as an index of the formability / ductility. It was observed that as the amount of silicon in the aluminising melt was gradually increased the measured ductility of the sheet sample also increased. Metallographic examination has shown that as the amount of silicon in the aluminising melt was increased the thickness of the intermediate compound layer, between the outer aluminum coat and the substrate steel, decreased. It was thus indicated from these experiments that the formability / ductility of the sheet was inversely related to the thickness of the interlayer. (author)

Stabilization/solidification of hot dip galvanizing ash using different binders.

Science.gov (United States)

Vinter, S; Montanes, M T; Bednarik, V; Hrivnova, P

2016-12-15

This study focuses on solidification of hot dip-galvanizing ash with a high content of zinc and soluble substances. The main purpose of this paper is to immobilize these pollutants into a matrix and allow a safer way for landfill disposal of that waste. Three different binders (Portland cement, fly ash and coal fluidized-bed combustion ash) were used for the waste solidification. Effectiveness of the process was evaluated using leaching test according to EN 12457-4 and by using the variance analysis and the categorical multifactorial test. In the leaching test, four parameters were observed: pH, zinc concentration in leachate, and concentration of chlorides and dissolved substances in leachate. The acquired data was then processed using statistical software to find an optimal solidifying ratio of the addition of binder, water, and waste to the mixture, with the aim to fulfil the requirement for landfill disposal set by the Council Decision 2003/33/EC. The influence on the main observed parameters (relative amount of water and a binder) on the effectiveness of the used method and their influence of measured parameters was also studied. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of chemical composition of steel on the structure of hot – dip galvanized coating

Directory of Open Access Journals (Sweden)

P. Pokorny

2016-01-01

Full Text Available This article describes the effect of the content of conventional steel impurity elements on the thickness and composition of the zinc layer. This article is focused primarily on low-temperature, batch hot-dip galvanizing; however, the continuous coating process is also mentioned. The main discussion covers galvanizing from pure zinc melt, and only touches on galvanizing from melts with the usual amounts of aluminium (0,2 wt. %. Silicon, phosphorus, aluminium and sulfur may have an especially negative effect on the mechanical properties of the coating and its final appearance. The content of ballast carbon and manganese has a rather limited effect on composition and coating thickness.

Report on best available techniques (BAT) at Finnish hot dip galvanizing plants in 2001; Selvitys parhaasta kaeytettaevissae olevasta tekniikasta (BAT) Suomen kuumasinkityslaitoksissa vuonna 2001

Energy Technology Data Exchange (ETDEWEB)

Hakala, I.

2002-02-01

Report presents hot dip (batch) galvanizing process and its emissions as well as measures to prevent and control them. Report has been prepared in cooperation with industry representatives and environmental authorities. Reference Document on Best Available Techniques in the Ferrous Metals Processing Industry and especially its part concerning batch galvanizing has been utilized. Also background information from the existing environmental permits as well as information collected by the questionnaires has been used. In year 2001 there were 18 hot dip (batch) galvanizing plants in Finland. Branch can be considered quite homogenous as there are only few variations in processes used. Waste management and recovery and as well as waste water treatment are well taken care of. At many plants treated process water is recycled back to the galvanizing process. Air emissions from hot dipping pot (dust, zinc, ammonium compounds, chlorides) are filtrated only at few plants. Therefore most of the environmental load at many plants is caused by air emissions as they can indirectly cause pollution also into soil and nearby water bodies. Instead of specific emission and consumption data and comparison between different techniques, report presents choice of measures and actions to be taken into account when applying best available techniques (BAT) at an installation level. Galvanizers can use the report as background information when assessing implementation of BAT at their own plants. Permitting authorities can utilize the report in the environmental permitting of the plants. (orig.)

Si、Mg、RE对热浸镀锌铝基合金镀层组织与性能的影响研究进展%Effects of Si, Mg and RE on Microstructure and Properties of Hot Dip Galvanized Alloy Coatings

Institute of Scientific and Technical Information of China (English)

周英伟; 高波

2017-01-01

热浸镀技术是钢铁材料长效防腐的一种有效方法,因其可以显著提高钢铁材料的耐蚀性能、延长材料的使用寿命而被广泛应用.近年来,随着科技水平的不断提高,传统的热浸镀层已经无法满足市场多样化的需求,多元合金镀层的研究成为热浸镀领域的研究热点.随着研究的不断深入,人们发现在热浸镀过程中添加合金元素能够明显提高热浸镀层的综合性能,但是合金元素的加入是如何影响镀层组织结构及性能是值得探讨的问题.为此,详细介绍了硅、镁、稀土等合金元素的加入对热浸镀层的微观组织、耐蚀性能和耐蚀机理的影响.通过列举国内外的研究实例,进一步分析了合金元素的添加量对热浸镀层性能的影响规律.最后提出,继续研究各种合金元素及其添加量对热浸镀层组织性能的影响规律及机制,并深入探讨添加合金元素之后,合金镀层中金属间化合物层的形成和生长规律,开发性能优异的新型热浸镀层及相应的热浸镀工艺是未来热浸镀技术的主要研究方向.%Hot dipping technology is an effective method for long-term corrosion of steel materials, it has been widely used as it can significantly improve corrosion resistance of steel materials and extend service life of the materials. Recently, with the continuous improvement of technological level, traditional hot-dip coating has failed to meet the demands of market diversifica-tion, and study on multicomponent alloy coating has become a hotspot in the field of hot dipping. With the constant deepening of study, it was found that overall performance of hot-dip coating could be greatly improved by adding alloy elements in the hot dipping process could significantly improve the comprehensive performance of the hot-dip coating. However, it was worthy to discuss how addition of alloying elements affected coating microstructure and performance. The effects of the

Characterization of solid wastes from two different hot-dip galvanizing processes; Caracterizacion de residuos solidos procedentes de dos procesos distintos de galvanizado en caliente por inmersion

Energy Technology Data Exchange (ETDEWEB)

Delvasto, P.; Casal-Ramos, J. a.; Gonzalez-Jordan, O.; Duran-Rodriguez, N. C.; Dominguez, J. R.; Moncada, P.

2012-11-01

Zinc dust and zinc ash from hot-dip galvanizing industries located in Venezuela were characterized using atomic spectroscopy, scanning electron microscopy, X-Ray diffraction and infrared spectroscopy. Dust was formed during the high-pressure drying process of the galvanized pieces, in a plant that uses a steel kettle to hold the molten zinc. Ash identified as A came from the same plant as the dust, while ash identified as B came from a hot-dip galvanizing plant which use a ceramic lined galvanizing furnace. Dust contained 98 wt % Zn, in metallic form. Both ash samples contained: Zn and ZnO, while Zn{sub 5}(OH){sub 8}Cl{sub 2}×H{sub 2}O and ZnCl{sub 2} were only found in ash B. Globally, ash “A” and ash “B” contain 71 and 75 wt % Zn, respectively. (Author)

Effect of Mg content on microstructure and corrosion behavior of hot dipped Zn–Al–Mg coatings

Energy Technology Data Exchange (ETDEWEB)

Yao, Caizhen; Lv, Haibing [Research Centre of Laser Fusion, CAEP, P.O.Box 919-988-5, Mianyang, Sichuan 621900 (China); Zhu, Tianping [Department of Chemical and Materials Engineering, The University of Auckland, PB 92019, Auckland 1142 (New Zealand); Zheng, Wanguo [Research Centre of Laser Fusion, CAEP, P.O.Box 919-988-5, Mianyang, Sichuan 621900 (China); Yuan, Xiaodong, E-mail: xdyuan@caep.cn [Research Centre of Laser Fusion, CAEP, P.O.Box 919-988-5, Mianyang, Sichuan 621900 (China); Gao, Wei, E-mail: w.gao@auckland.ac.nz [Department of Chemical and Materials Engineering, The University of Auckland, PB 92019, Auckland 1142 (New Zealand)

2016-06-15

In this article, Zn–Al–Mg coatings were prepared by hot dipping method. The surface morphology, cross–section microstructure, microhardness, composition, corrosion behaviour of ZAM coatings were investigated by using X–ray diffraction (XRD), Optical microscope, Environmental scanning electron microscopy equipped with EDS (FESEM–EDS), Microhardness tester and Electrochemical analysis respectively. Corrosion test was also performed in a standard salt fog spray chamber. Microstructure studies indicates that Zn grain size was refined and eutectic areas at Zn grain boundary areas increased with increasing Mg content. ZA5M1.5 and ZA5M2 coatings have two distinct layers. Mg tends to exist in the outer layer while Al is in the inner layer. The inner layer is composed of Al{sub 5}Fe{sub 2}Zn{sub 0.4} intermetallic, which may to contribute to the microhardness. The outer layer is Zn grains surrounded by Zn–Mg etutectics, which may improve the corrosion resistance. The microhardness is more than 700 HV{sub 50g} for Al-rich layer and around 151 HV{sub 25g} for Mg-rich layer. The improved corrosion resistance of Zn–5%Al-1.5%Mg coating comes from the corrosion product of flocculent type simonkolleite, which prolongs the micro-path and impedes the movement of O{sub 2} and H{sub 2}O, ultimately retards the overall corrosion process. - Highlights: • Two-layer structured Zn–Al–Mg coatings were prepared by hot dipping method. • Mg exists in the outer layer while Al exists in the inner layer of Zn–Al–Mg coating. • Zn–Al–Mg coating has better protective ability than Zn and Zn–Al coatings. • The Mg-modified simonkolleite is the reason of the enhanced corrosion resistance.

Effect of confinement on bond strength of hot-dip galvanized lap splices in concrete structures

International Nuclear Information System (INIS)

Fakhran, Mazen

2004-01-01

Galvanizing the reinforcing steel is one of the methods used to protect bars against corrosion. Galvanizing is a hot dip process where the reinforcing bars are immersed in an aqueous pre flux solution of zinc ammonium chloride at a controlled temperature between 840 and 850 degrees F. In 2001, a research program was started at AUB to evaluate experimentally the effect of hot dip galvanizing on the bond capacity of tension lap splices anchored in full-scale beam specimens designed to fail in bond splitting mode. The test results indicated that the use of galvanized bars had a negligible effect on bond strength of reinforcement in normal strength. However, galvanizing caused an average of 20 percent decrease in bond strength of reinforcement in high strength concrete. The primary objective of research reported in this thesis, is the need to find a solution to eliminate the bond reduction of galvanized bars in high strength concrete. It is significant to evaluate the positive effect of the addition of transverse reinforcement in the splice region. The hypothesis to be tested is that such transverse reinforcement will insure uniform bond stress distribution over the entire splice region, thus mobilizing all bar lugs along the splice in the stress transfer mechanism between the bar and the surrounding concrete. Such mechanism might reduce the significant decrease in bond strength in high strength concrete due to galvanizing. To achieve this objective, eighteen full-scale beam specimens were tested in positive bending. Each beam was reinforced with bars spliced in a constant moment region at midspam. The splice length was chosen in such a way that the beams failed in bond splitting of the concrete cover in the splice region. The main variables were type of coating (black or galvanized bars), bar size (20, 25 and 32 mm), and amount of transverse reinforcement in the splice region (0, 2 or 4 stirrups). The test results indicated that confinement did not have a significant

Effect of Mg on the Microstructure and Corrosion Resistance of the Continuously Hot-Dip Galvanizing Zn-Mg Coating

Directory of Open Access Journals (Sweden)

Anping Dong

2017-08-01

Full Text Available The microstructure of continuously hot-dip galvanizing Zn-Mg coating was investigated in order to obtain the mechanism of the effects of Mg on the corrosion resistance. In this paper, the vertical section of the Zn-0.20 wt % Al-Mg ternary phase diagram near the Al-low corner was calculated. The results indicates that the phase composition of the Zn-0.20 wt % Al-Mg ternary phase diagram near the Al-low corner is the same as Zn-Mg binary phase diagram, suggesting Al in the Zn-Mg (ZM coatings mainly concentrates on the interfacial layer between the coating and steel substrate. The microstructure of continuously hot-dip galvanizing ZM coatings with 0.20 wt % Al containing 1.0–3.0 wt % Mg was investigated using tunneling electron microscopy (TEM. The morphology of Zn in the coating changes from bulk to strip and finally to mesh-like, and the MgZn2 changes from rod-like to mesh-like with the Mg content increasing. Al in the ZM coatings mainly segregates at the Fe2Al5 inhibition layer and the Mg added to the Zn bath makes this inhibition layer thinner and uneven. Compared to GI coating, the time of the first red rust appears increases by more than two-fold and expansion rate of red rust reduces by more than four-fold in terms of salt spray experiment. The ZM coating containing 2.0 wt % Mg has the best corrosion resistance. The enhanced corrosion resistance of ZM coatings mainly depends on different corrosion products.

Effect of strip temperature on the formation of an Fe{sub 2}Al{sub 5} inhibition layer during hot-dip galvanizing

Energy Technology Data Exchange (ETDEWEB)

Dutta, Monojit [R and D Division, Tata Steel Ltd., Jamshedpur 831001 (India)], E-mail: monoron@yahoo.com; Singh, Shiv Brat [Department of Metallurgical and Materials Engineering, Indian Institute of Technology, Kharagpur 721302 (India)

2009-04-15

The theory of nucleation has been employed to derive expressions for the formation of an Fe{sub 2}Al{sub 5} layer during commercial strip galvanizing. This is then used to show the effect of the strip entry temperature on the nucleation of the Fe{sub 2}Al{sub 5} layer. An attempt was also made to verify this effect through controlled experiments in a hot-dip galvanizing simulator and electron microscopic characterization of a few samples.

Formation of microstructural features in hot-dip aluminized AISI 321 stainless steel

Science.gov (United States)

Huilgol, Prashant; Rajendra Udupa, K.; Udaya Bhat, K.

2018-02-01

Hot-dip aluminizing (HDA) is a proven surface coating technique for improving the oxidation and corrosion resistance of ferrous substrates. Although extensive studies on the HDA of plain carbon steels have been reported, studies on the HDA of stainless steels are limited. Because of the technological importance of stainless steels in high-temperature applications, studies of their microstructural development during HDA are needed. In the present investigation, the HDA of AISI 321 stainless steel was carried out in a pure Al bath. The microstructural features of the coating were studied using scanning electron microscopy and transmission electron microscopy. These studies revealed that the coating consists of two regions: an Al top coat and an aluminide layer at the interface between the steel and Al. The Al top coat was found to consist of intermetallic phases such as Al7Cr and Al3Fe dispersed in an Al matrix. Twinning was observed in both the Al7Cr and the Al3Fe phases. Furthermore, the aluminide layer comprised a mixture of nanocrystalline Fe2Al5, Al7Cr, and Al. Details of the microstructural features are presented, and their formation mechanisms are discussed.

Nicotinic acid as a nontoxic corrosion inhibitor for hot dipped Zn and Zn-Al alloy coatings on steels in diluted hydrochloric acid

Energy Technology Data Exchange (ETDEWEB)

Ju Hong [Institute of Oceanology, Chinese Academy of Sciences, Qingdao 266071 (China); Graduate School, Chinese Academy of Sciences, Beijing 100039 (China); Li Yan [Institute of Oceanology, Chinese Academy of Sciences, Qingdao 266071 (China)], E-mail: yanlee@ms.qdio.ac.cn

2007-11-15

The inhibition effect of nicotinic acid for corrosion of hot dipped Zn and Zn-Al alloy coatings in diluted hydrochloric acid was investigated using quantum chemistry analysis, weight loss test, electrochemical measurement, and scanning electronic microscope (SEM) analysis. Quantum chemistry calculation results showed that nicotinic acid possessed planar structure with a number of active centers, and the populations of the Mulliken charge, the highest occupied molecular orbital (HOMO), and the lowest unoccupied molecular orbital (LUMO) were found mainly focused around oxygen and nitrogen atoms, and the cyclic of the benzene as well. The results of weight loss test and electrochemical measurement indicated that inhibition efficiency (IE%) increased with inhibitor concentration, and the highest inhibition efficiency was up to 96.7%. The corrosion inhibition of these coatings was discussed in terms of blocking the electrode reaction by adsorption of the molecules at the active centers on the electrode surface. It was found that the adsorption of nicotinic acid on coating surface followed Langmuir adsorption isotherm with single molecular layer, and nicotinic acid adsorbed on the coating surface probably by chemisorption. Nicotinic acid, therefore, can act as a good nontoxic corrosion inhibitor for hot dipped Zn and Zn-Al alloy coatings in diluted hydrochloric acid solution.

Development of Zn-Al-Cu coatings by hot dip coated technology: preparation and characterization

International Nuclear Information System (INIS)

Cervantes, J.; Barba, A.; Hernandez, M. A.; Salas, J.; Espinoza, J. L.; Denova, C.; Torres-Villasenor, G.; Conde, A.; Covelo, A.; Valdez, R.

2013-01-01

In the present study, research concerning Zn-Al-Cu coatings on low carbon steels has been conducted in order to characterize different properties obtained by a hot-dip coated process. The results include preparation procedure as well as the processing parameters of the coatings. The obtained coatings were subjected to a cold rolling process followed by an anneal heat treatment at different temperatures and under different time conditions. The structural characteristics of coatings have been investigated by optical and electron microscopy. The mechanical properties were obtained by using micro-hardness testing, deep drawing and wear tests whereas chemical analyses were carried out using the SEM/EDAX microprobe. The corrosion properties were achieved by using a salt spray fog chamber and potentiodynamic tests in a saline solution. The coatings are resistant to corrosion and wear in the presence of sodium chloride, therefore, the coatings could be an attractive alternative for application in coastal areas, and adequate wear adhesive resistance. (Author)

Hot-Dip Aluminizing on AISI F55–UNS S32760 Super Duplex Stainless Steel Properties: Effect of Thermal Treatments

Directory of Open Access Journals (Sweden)

Andrea Francesco Ciuffini

2017-11-01

Full Text Available The behavior of super duplex stainless steels AISI F55-UNS S32760 in hot-dip aluminizing process has been studied, investigating the influence of cold working and of different initial microstructures obtained through a preliminary thermal treatment. The microstructural features examined are the secondary austenite precipitation, the static recovery of ferrite and the thermal dissolution of austenite within ferritic matrix. The hot-dip aluminizing temperature has been optimized through sessile drop tests. The treatment has been performed at 1100 °C for 300 s, 900 s and 2700 s. A strong chemical interaction occurs, generating intermetallic compounds at the interface. Molten aluminum interacts exclusively with the ferritic phase due to its much higher diffusivity in this phase coupled with its marked ferrite-stabilizer behavior. Thus, the influence of cold working is not remarkable, since the strains are mainly allocated by austenitic phase. The diffusivity of aluminum increases due to lattice defects thermally generated and, mainly, to influence given by grain boundaries, multiplied by secondary austenite precipitation, which act as short-circuit diffusion paths. Ni and Cr contents in the ferritic matrix have an influence but not highly relevant. Then, the best starting condition of the super duplex stainless steel substrates, to obtain a thick interfacial layer, are the thermal annealing at 1080 °C for 360 s/mm after a solution thermal treatment at 1300 °C for 60 s/mm.

The effect of zinc bath temperature on the morphology, texture and corrosion behaviour of industrially produced hot-dip galvanized coatings

Directory of Open Access Journals (Sweden)

A. Bakhtiari

2014-03-01

Full Text Available The purpose of this work is to identify the influence of zinc bath temperature on the morphology, texture and corrosion behavior of hot-dip galvanized coatings. Hot-dip galvanized samples were prepared at temperature in the range of 450-480 °C in steps of 10 °C, which is the conventional galvanizing temperature range in the galvanizing industries. The morphology of coatings was examined with optical microscopy and scanning electron microscopy (SEM. The composition of the coating layers was determined using energy dispersive spectroscopy (EDS analysis. The texture of the coatings was evaluated using X-ray diffraction. Corrosion behavior was performed using salt spray cabinet test and Tafel extrapolation test. From the experimental results, it was found that increasing the zinc bath temperature affects the morphology of the galvanized coatings provoking the appearance of cracks in the coating structure. These cracks prevent formation of a compact structure. In addition, it was concluded that (00.2 basal plane texture component was weakened by increasing the zinc bath temperature and, conversely, appearance of (10.1 prism component, (20.1 high angle pyramidal component and low angle component prevailed. Besides, coatings with strong (00.2 texture component and weaker (20.1 components have better corrosion resistance than the coatings with weak (00.2 and strong (20.1 texture components. Furthermore, corrosion resistance of the galvanized coatings was decreased by increasing the zinc bath temperature.

In Situ Apparatus to Study Gas-Metal Reactions and Wettability at High Temperatures for Hot-Dip Galvanizing Applications

Science.gov (United States)

Koltsov, A.; Cornu, M.-J.; Scheid, J.

2018-02-01

The understanding of gas-metal reactions and related surface wettability at high temperatures is often limited due to the lack of in situ surface characterization. Ex situ transfers at low temperature between annealing furnace, wettability device, and analytical tools induce noticeable changes of surface composition distinct from the reality of the phenomena.Therefore, a high temperature wettability device was designed in order to allow in situ sample surface characterization by x-rays photoelectron spectroscopy after gas/metal and liquid metal/solid metal surface reactions. Such airless characterization rules out any contamination and oxidation of surfaces and reveals their real composition after heat treatment and chemical reaction. The device consists of two connected reactors, respectively, dedicated to annealing treatments and wettability measurements. Heat treatments are performed in an infrared lamp furnace in a well-controlled atmosphere conditions designed to reproduce gas-metal reactions occurring during the industrial recrystallization annealing of steels. Wetting experiments are carried out in dispensed drop configuration with the precise control of the deposited droplets kinetic energies. The spreading of drops is followed by a high-speed CCD video camera at 500-2000 frames/s in order to reach information at very low contact time. First trials have started to simulate phenomena occurring during recrystallization annealing and hot-dip galvanizing on polished pure Fe and FeAl8 wt.% samples. The results demonstrate real surface chemistry of steel samples after annealing when they are put in contact with liquid zinc alloy bath during hot-dip galvanizing. The wetting results are compared to literature data and coupled with the characterization of interfacial layers by FEG-Auger. It is fair to conclude that the results show the real interest of such in situ experimental setup for interfacial chemistry studies.

Origin of intragranular crystallographic misorientations in hot-dip Al-Zn-Si coatings

International Nuclear Information System (INIS)

Niederberger, Ch.; Michler, J.; Jacot, A.

2008-01-01

The origin of intragranular variations of the crystallographic orientation in hot-dip Al-Zn-Si coatings is discussed based on new experimental results and modelling. The solidification microstructure in as-received 55Al-43.4Zn-1.6Si (in wt.%) coatings deposited on steel plates in an industrial production line was analyzed by electron backscattered diffraction, glow-discharge optical emission spectroscopy and atomic force microscopy (AFM). The results were compared with those obtained in coatings re-solidified under different cooling and mechanical loading conditions. Continuous variations of the crystallographic orientation as large as 35 deg. were observed within individual grains of Al-Zn-Si, consistent with previous studies. However, the mechanisms previously proposed for the origin of intragranular crystallographic misorientations had to be revisited. The new experimental data acquired during this study indicate that the solidification shrinkage accumulating in the area of the grain envelope is the driving force for the formation of intragranular misorientations. The solidification shrinkage leads to the development of tensile stresses in the oxide film covering the coating while it solidifies. Estimations based on AFM profiles and phase field simulations of the dendritic structure indicate that the stresses applied on the dendrite network are sufficient to deform plastically the dendrite arms during solidification

Thickness measurement of Sn-Ag hot dip coatings on Large Hadron Collider Superconducting strands by coulometry

CERN Document Server

Arnau-Izquierdo, G; Oberli, L R; Scheuerlein, C; Taborelli, M; 10.1149/1.1715094

2004-01-01

Amperostatic coulometry is applied for the thickness measurement of Sn-Ag hot dip coatings, which comprise an extended Sn-Cu interdiffusion layer. Complementary measurements, notably weight loss, X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDS), X-ray fluorescence (XRF) and dynamic secondary ion mass spectroscopy (DSIMS) have been performed in order to obtain a better interpretation of the coulometry results. Based on the experimental results presented in this article the three potential changes that are observed during coulometry measurements are ascribed to (1) the entire dissolution of pure Sn, (2) the formation of a CuCl salt layer and (3) the surface passivation. The measurement of the pure Sn mass is well reproducible despite of strong coating thickness variations that are detected by XRF. Several experimental problems, in particular a coating undercutting, hamper the determination of the Sn mass in the intermetallic Sn-Cu layer.

Simple Heat Treatment for Production of Hot-Dip Galvanized Dual Phase Steel Using Si-Al Steels

Science.gov (United States)

Equihua-Guillén, F.; García-Lara, A. M.; Muñíz-Valdes, C. R.; Ortíz-Cuellar, J. C.; Camporredondo-Saucedo, J. E.

2014-01-01

This work presents relevant metallurgical considerations to produce galvanized dual phase steels from low cost aluminum-silicon steels which are produced by continuous strip processing. Two steels with different contents of Si and Al were austenized in the two-phase field ferrite + austenite (α + γ) in a fast manner to obtain dual phase steels, suitable for hot-dip galvanizing process, under typical parameters of continuous annealing processing line. Tensile dual phase properties were obtained from specimens cooled from temperature below Ar3, held during 3 min, intermediate cooling at temperature above Ar1 and quenching in Zn bath at 465 °C. The results have shown typical microstructure and tensile properties of galvanized dual phase steels. Finally, the synergistic effect of aluminum, silicon, and residual chromium on martensite start temperature ( M s), critical cooling rate ( C R), volume fraction of martensite, and tensile properties has been studied.

THE METHOD OF ROLL SURFACE QUALITY MEASUREMENT FOR CONTINUOUS HOT DIP ZINC COATED STEEL SHEET PRODUCTION LINE

Directory of Open Access Journals (Sweden)

Ki Yong Choi

2015-01-01

Full Text Available The present paper describes a developed analyzing system of roll surface during the process of continuous hot dip zinc coated steel sheet production line, in particular, adhering problem by transferred inclusions from roll to steel sheet surface during annealing process so called the pickup. The simulated test machine for coated roll surface in processing line has been designed and performed. The system makes it possible to analyze roll surface condition according to pickup phenomena from various roll coatings concerning operating conditions of hearth rolls in annealing furnace. The algorithm of fast pickup detection on surface is developed on the base of processing of several optical images of surface. The parameters for quality estimation of surface with pickups were developed. The optical system for images registration and image processing electronics may be used in real time and embed in processing line.

Microstructure development and mechanical properties of quenching and partitioning (Q and P) steel and an incorporation of hot-dipping galvanization during Q and P process

Energy Technology Data Exchange (ETDEWEB)

Sun, Jing; Yu, Hao, E-mail: yhzhmr@126.com

2013-12-01

The “quenching and partitioning” (Q and P) process has recently been substantiated to be a unique technological route for the production of high strength steels with significant amounts of retained austenite, and thus to provide better combination of strength and ductility. In this work, intercritically annealed specimens followed by Q and P treatment have been applied to low-carbon steel with chemical composition typical for conventional TRIP-assisted steels. Microstructure of the steel treated by the Q and P process was characterized by means of optical microscope, SEM, TEM and XRD. The study suggests that microstructure is mainly composed of ferrite, lath martensite, martensite–austenite islands, retained austenite and a small amount of bainite formed during partitioning. The fraction of bainite formed during partitioning is proportional to quenching temperature. The mechanical property of specimen treated by the Q and P process exhibits an improved combination of strength and ductility than that of the Q and T process. Two schemes of hot-dipping galvanization processes were designed. The results indicate that both hot-dip galvanizing schemes present a limited reduction in tensile strength and a slight enhancement of ductility. The scheme of galvanizing and partitioning after the quenching progress shows a better combination of strength and ductility.

Effect of Annealing Temperature on Microstructure and Mechanical Properties of Hot-Dip Galvanizing DP600 Steel

Science.gov (United States)

Hai-yan, Sun; Zhi-li, Liu; Yang, Xu; Jian-qiang, Shi; Lian-xuan, Wang

Hot-dip galvanizing dual phase steel DP600 steel grade with low Si was produced by steel plant and experiments by simulating galvanizing thermal history. The microstructure was observed and analyzed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The effect of different annealing temperatures on the microstructure and mechanical properties of dual-phase steel was also discussed. The experimental results show that the dual-phase steel possesses excellent strength and elongation that match EN10346 600MPa standards. The microstructure is ferrite and martensite. TEM micrograph shows that white ferrite with black martensite islands inlay with a diameter of around 1um and the content of 14 18%. The volume will expand and phase changing take the form of shear transformation when ferrite converted to martensite. So there are high density dislocations in ferrite crystalline grain near martensite. The martensite content growing will be obvious along with annealing temperature going up. But the tendency will be weak when temperature high.

Research on the Microstructures and Mechanical Properties of Ti Micro-Alloyed Cold Rolled Hot-Dip Galvanizing DP980 Steel

Science.gov (United States)

Han, Yun; Kuang, Shuang; Qi, Xiumei; Xie, Chunqian; Liu, Guanghui

Effects of galvanizing simulation parameters on microstructures and mechanical properties of Ti-microalloyed cold rolled hot-dip galvanizing DP980 steel were investigated in this study by optical microscopy (OM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS) and tensile test. Moreover, the precipitation behavior of Ti in the experimental steel was also studied. The results show that, as the heating temperature increases, the tensile strength of experimental galvanizing DP980 steel decreases while the yield ratio and elongation of the steel are enhanced. The microstructures of experimental steels exhibit typical dual phase steel character and the volume fractions of MA islands are almost 30%. In addition, lots of nano-sized TiC precipitates can be found in the ferrite grains.

Evaluation of surface characteristics under fretting of electrical contacts: Removal behaviour of hot dipped tin coating

International Nuclear Information System (INIS)

Park, Young Woo; Ramesh Bapu, G.N.K.; Lee, Kang Yong

2009-01-01

The fretting corrosion behaviour of hot dipped tin coating is investigated at low fretting cycles at ±25 μm displacement amplitude, 0.5N normal load, 3 Hz frequency, 45-50% relative humidity, and 25 ± 1 deg. C temperature. The typical characteristics of the change in contact resistance with fretting cycles are explained. The fretted surface is examined using laser scanning microscope, scanning electron microscope and energy dispersive X-ray analysis to assess the surface profile, extent of fretting damage, extent of oxidation and elemental distribution across the contact zone. The interdependence of extent of wear and oxidation increases the complexity of the fretting corrosion behaviour of tin coating. The variation of contact resistance clearly revealed the fretting of tin coating from 50 to 1200 cycles and the fretting of the substrate above 1200 cycles. The observed low and stable contact resistance region and the fluctuating resistance region at various fretting cycles are explained and substantiated with Scanning electron microscopy (SEM), laser scanning microscope (LSM) and energy dispersive analysis of X-rays (EDAX) analysis results of the fretted surface.

Mechanism and prevention of edge over coating in continuous hot-dip galvanizing

Energy Technology Data Exchange (ETDEWEB)

Takeishi, Y.

2000-11-01

In order to clarify the mechanism of edge over coating (EOC) for continuous hot-dip galvanizing, a visualization test of the gas flow on strip and a cold model test to measure the profile of the coating thickness at the strip edge were carried out. Outward deflected gas flow was observed at the strip edge and EOC developed in the absence of gas wiping. With gas wiping, EOC developing below the wiping position is reduced by the impinging pressure of the gas wiping jet, and the film thickness becomes approximately uniform at the gas wiping position. However, upward of the gas wiping position. EOC increases again and the outward deflected gas flow on the strip edge sweeps the liquid film to the strip edge. EOC is considered to develop at the location where the dynamic pressure of the outward deflected gas flow balances with the surface tension. For the prevention of EOC, edge masking was devised and the effects which reduce EOC were measured in the cold model test and on a commercial line test. The edge mask which can be kept farther away from the strip edge is more effective for preventing EOC than the edge plates. The optimum dimension of the edge mask is 30mm in width and 75-100 mm in depth, and installing it at 4-10mm away from the strip edge is most effective. It was confirmed by the commercial line test that the edge mask can reduce EOC from 45% to less than 10%. (author)

Microstructure and High-temperature Wear Behavior of Hot-dipped Aluminized Coating on Different Substrate Materials

Directory of Open Access Journals (Sweden)

ZHOU De-qin

2018-02-01

Full Text Available The aluminized 45 and H13 steel were prepared via hot-dipped aluminizing and subsequently high-temperature diffusion treatment. The phase, morphology and composition of aluminized coating were characterized by XRD,SEM and EDS methods. Comparative study was performed on unlubricated sliding wear behavior of plating under different substrates on a pin-on-disc wear tester, and the wear mechanism was explored. The results show that the coating is composed of ductile phases FeAl and Fe3Al. Kikendall porosity parallel to the surface exists around the interface of the two phases; because of the carbide particles agglomeration, the bond between the coating and H13 steel is apparently inferior to that in the case of 45 steel; the aluminized 45 steel possesses an excellent wear resistance under 50-200N at 400℃, whereas mild-to-severe wear transition occurs when the temperature increases to 600℃. The wear rate of the aluminized H13 steel reaches the lowest at 400℃, then slightly increases at 600℃. The wear mechanisms of Fe-Al coating are mainly predominated by oxidative mild wear, whereas the extrusion wear prevails in the process for aluminized 45 steel at 600℃.

Relationship between surface structure of silicon containing steel and adhesion of hot dip galvanized coating; Si gan'yu koban no hyomen kozo to yoyu aen mekki micchakuseino kankei

Energy Technology Data Exchange (ETDEWEB)

Tsuchiya, Y.; Hashimoto, S.; Ishibashi, Y. [Kokan Keisoku K.K., Kawasaki (Japan); Inagaki, J. [NKK Corp., Tokyo (Japan); Fukuda, Y. [Shuibuoka University, Shizuoka (Japan)

2000-06-01

The surface of the annealed steel and the exfoliated interface of the coating for the hot dip galvanized Si containing steel sheets was characterized by using SEM (Scanning Electron Microscope), AES (Auger Electron Spectroscopy) and TEM (Transmission Electron Microscopy). The adhesion of the coatings have depended on the Si content of the steel. It have been found that MnSiO{sub 3} particles are formed at the surface of the annealed steels having high Si content and that two types of grain having different distribution of the oxide exist in the steels. Large oxide particles have been formed in one type of grain and small particles are formed in the other type of grain. The different type of Fe-Zn alloy are formed on two types of grains. It have been observed that the oxide particles exist at the interface of exfoliated coatings after the adhesion test for the steels with high Si content. The distribution of the oxide particles observed at the bottom of the exfoliated coating is quite similar to that of the surface oxide of the annealed steel. From these results, the exfoliation of the coating has initiated at the oxide particles of the steel surface that has been not reduced during the hot dip galvanizing. (author)

Reduce of adherence problems in galvanised processes through data mining techniques; Reducciond e problemas de adherencia en procesos de galvanizado mediante tecnicas de mineria de datos

Energy Technology Data Exchange (ETDEWEB)

Martinez de Pison, F. J.; Ordieres, J.; Pernia, A.; Alba, F.; Torre, V.

2007-07-01

This paper presents an example of the application of data mining techniques to obtain hidden knowledge from the historical data of a hot dip galvanizing process and to establish rules to improve quality in the final product and to reduce errors in the process. For this purpose, the tuning records of a hot dip galvanizing line where coils with adherence problems in the zinc coating had been identified were used as starting point. From the database of the process, the classical data mining approach was applied to obtain and analyze a number of decision trees hat classified two types of coils, i.e. those with the right adherence and those with irregular adherence. The variables and values that might have influenced the quality of the coating were extracted from these tress. Several rules that may be applied to reduce the number of faulty coils with adherence problems were also established. (Author) 24 refs.

Heat treatment, microstructure and mechanical properties of a C–Mn–Al–P hot dip galvanizing TRIP steel

International Nuclear Information System (INIS)

Ding, Wei; Hedström, Peter; Li, Yan

2016-01-01

Heat treatments of a hot dip galvanizing TRIP (Transformation induced plasticity) steel with chemical composition 0.20C-1.50Mn-1.2Al-0.07P(mass%) were performed in a Gleeble 3500 laboratory equipment. The heat treatment process parameters were varied to investigate the effect of intercritical annealing temperature as well as isothermal bainitic transformation (IBT) temperature and time, on the microstructure and the mechanical properties. The microstructure was investigated using scanning electron microscopy, transmission electron microscopy and x-ray diffraction, while mechanical properties were evaluated by tensile testing. Furthermore, to generate a better understanding of the phase transformations during heat treatment, dilatometry trials were conducted. The desired microstructure containing ferrite, bainite, retained austenite and martensite was obtained after the heat treatments. It was further found that the IBT is critical in determining the mechanical properties of the steel, since it controls the fraction of bainite. With increasing bainite fraction, the fraction of retained austenite increases while the fraction of martensite decreases. The mechanical properties of the steel are excellent with a tensile strength above 780 MPa (expect in one case) and elongation above 22%.

Heat treatment, microstructure and mechanical properties of a C–Mn–Al–P hot dip galvanizing TRIP steel

Energy Technology Data Exchange (ETDEWEB)

Ding, Wei [School of Material and Metallurgy, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Department of Materials Science and Engineering, KTH Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Bayan Obo multimetallic resource comprehensive utilization Key lab, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Hedström, Peter [Department of Materials Science and Engineering, KTH Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Li, Yan [Department of Materials Science and Engineering, KTH Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Bayan Obo multimetallic resource comprehensive utilization Key lab, Inner Mongolia University of Science and Technology, Baotou 014010 (China)

2016-09-30

Heat treatments of a hot dip galvanizing TRIP (Transformation induced plasticity) steel with chemical composition 0.20C-1.50Mn-1.2Al-0.07P(mass%) were performed in a Gleeble 3500 laboratory equipment. The heat treatment process parameters were varied to investigate the effect of intercritical annealing temperature as well as isothermal bainitic transformation (IBT) temperature and time, on the microstructure and the mechanical properties. The microstructure was investigated using scanning electron microscopy, transmission electron microscopy and x-ray diffraction, while mechanical properties were evaluated by tensile testing. Furthermore, to generate a better understanding of the phase transformations during heat treatment, dilatometry trials were conducted. The desired microstructure containing ferrite, bainite, retained austenite and martensite was obtained after the heat treatments. It was further found that the IBT is critical in determining the mechanical properties of the steel, since it controls the fraction of bainite. With increasing bainite fraction, the fraction of retained austenite increases while the fraction of martensite decreases. The mechanical properties of the steel are excellent with a tensile strength above 780 MPa (expect in one case) and elongation above 22%.

Influence of silicon on hot-dip aluminizing process and subsequent oxidation for preparing hydrogen/tritium permeation barrier

Energy Technology Data Exchange (ETDEWEB)

Han, Shilei; Li, Hualing; Wang, Shumao; Jiang, Lijun; Liu, Xiaopeng [Energy Materials and Technology Research Institute, General Research Institute for Nonferrous Metals, Beijing 100088 (China)

2010-04-15

The development of the International Thermonuclear Experimental Reactor (ITER) requires the production of a material capable of acting as a hydrogen/tritium permeation barrier on low activation steel. It is well known that thin alumina layer can reduce the hydrogen permeation rate by several orders of magnitude. A technology is introduced here to form a ductile Fe/Al intermetallic layer on the steel with an alumina over-layer. This technology, consisting of two main steps, hot-dip aluminizing (HDA) and subsequent oxidation behavior, seems to be a promising coating method to fulfill the required goals. According to the experiments that have been done in pure Al, the coatings were inhomogeneous and too thick. Additionally, a large number of cracks and porous band could be observed. In order to solve these problems, the element silicon was added to the aluminum melt with a nominal composition. The influence of silicon on the aluminizing and following oxidation process was investigated. With the addition of silicon into the aluminum melt, the coating became thinner and more homogeneous. The effort of the silicon on the oxidation behavior was observed as well concerning the suppression of porous band and cracks. (author)

Analysis Of Effect Of Mechanical Properties Of Aluminum Alloy Addition Of Zinc Corrosion Resistance Of Carbon Steel A325 Bolts Process Of Hot Dip Galvanizing

Directory of Open Access Journals (Sweden)

Ery Diniardi

2015-08-01

Full Text Available The world oil industry are common in offshore areas that are included in a corrosive environment so that the low-carbon steel bolts A325 will gradually corroded. Therefore an alternative that can be done to reduce the corrosion rate that is by coating with a Hot dip galvanizing method. The purpose of this study to improve the quality of products from low carbon steel bolts A325 with the addition of Zinc Aluminium alloy on the results of the Hot Dip Galvanizing. Results of testing the hardness of the lowest obtained in quenching time of 30 seconds is 162 037 HVN and the highest hardness obtained on quenching time of 60 seconds is 203 688 HVN. To microstructure shows that the phase Eta which is soft on the surface of the outermost started a little not as much time quenching 30 seconds so that the nature of its decline and violence increased the phase Zeta that are hard are widely spread meet the layer of phase resulting in hardness of the coating while quenching 45 seconds exceed the hardness of quenching time of 30 seconds. Results of analysis of the rate of corrosion that galvanized coating on each test is different and the structure of ferrite and pearlite it looks clear. For quenching time of 30 seconds obvious difference in galvanized layer thicker than quenching time of 45 and 60 seconds. This happens because of the influence of factors zinc layer that coats the base material so that decreased levels of corrosion is comparable to the time Salt Spray Test SST performed.

High chromium nickel base alloys hot cracking susceptibility

International Nuclear Information System (INIS)

Tirand, G.; Primault, C.; Robin, V.

2014-01-01

High Chromium nickel based alloys (FM52) have a higher ductility dip cracking sensitivity. New filler material with higher niobium and molybdenum content are developed to decrease the hot crack formation. The behavior of these materials is studied by coupling microstructural analyses and hot cracking test, PVR test. The metallurgical analyses illustrate an Nb and Mo enrichment of the inter-dendritic spaces of the new materials. A niobium high content (FM52MSS) induces the formation of primary carbide at the end of solidification. The PVR test reveal a solidification crack sensitivity of the new materials, and a lowest ductility dip cracking sensitivity for the filler material 52MSS. (authors)

Effect of UV-C radiation and hot water on the calcium content and postharvest quality of apples

International Nuclear Information System (INIS)

Hemmaty, S.; Moallemi, N.; Naseri, L.

2007-01-01

To increase the storage shelf life of 'Red Delicious' and 'Golden Delicious' apples they were treated with UV-C irradiation at doses of 0, 5 and 15 min irradiation at 1.435 x 10 -4 W/square cm - and with hot water containing 4% CaCl 2 at four levels (control, dipping at 25 deg C for 10 min, dipping at 38 deg C for 5 min and dipping in 54 deg C for 1 min) in a factorial design with 4 replicates. The results showed that UV-C irradiation and dipping of fruit in hot water increased the storage life and improved fruit quality factors in 'Red Delicious' and 'Golden Delicious' apples at the end of cold storage. Both UV-C and hot water treatments decreased pH and total soluble solids/titratable acids ratio and increased fruit titratable acids and firmness. UV-C and hot water treatment increased fruit Ca content during storage. The results showed that UV-C and hot water treatment can retard fruit ripening and maintain fruit quality in cold storage. These treatments can also increase Ca concentration of fruit flesh and thus increase the nutritional value of the apples. (author) [es

Comparative life cycle cost assessment of painted and hot-dip galvanized bridges.

Science.gov (United States)

Rossi, B; Marquart, S; Rossi, G

2017-07-15

The study addresses the life cycle cost assessment (LCCA) of steel bridges, focusing on the maintenance activities and the maintenance scenario. Firstly, the unit costs of maintenance activities and their durability (i.e. the time between two activities) are evaluated. Pragmatic data are provided for the environment category C4 and for three activities: Patch Up, Overcoating and Remove & Replace. A comparative LCCA for a typical hypothetic steel girder bridge is carried out, either painted or hot-dip galvanized (HDG), in the environmental class C4. The LCC versus the cumulated life is provided for both options. The initial cost of the steel unpainted option is only 50.3% of the HDG option. It is shown that after 'Overcoating' occurring at 18.5 years, the total Net Present Value (NPV) of the painted option surpasses that of the HDG option. A sensitivity analysis of the NPV to the cost and service life parameters, the escalation and discount rates is then performed. The discount and escalation rates, considerably influences the total LCC, following a non-linear trend. The total LCC decreases with the discount rate increasing and, conversely, increases with the escalation rate increasing. Secondly, the influence of the maintenance scenario on the total LCC is assessed based on a probabilistic approach. A permutation of the three independent maintenance activities assumed to occur six times over the life of the bridge is considered and a probability of occurrence is associated to each unique scenario. The most probable scenarios are then classified according to their NPV or achieved service life. This approach leads to the definition of a cost-effective maintenance scenario i.e. the scenario, within all the considered permutations, that has the minimum LCC in a range of lifespan. Besides, the probabilistic analysis also shows that, whatever the scenario, the return on investment period ranges between 18.5 years and 24.2 years. After that period, the HDG option becomes

Influence of Gas Atmosphere Dew Point on the Selective Oxidation and the Reactive Wetting During Hot Dip Galvanizing of CMnSi TRIP Steel

Science.gov (United States)

Cho, Lawrence; Lee, Seok Jae; Kim, Myung Soo; Kim, Young Ha; De Cooman, Bruno C.

2013-01-01

The selective oxidation and reactive wetting of intercritically annealed Si-bearing CMnSi transformation-induced plasticity steels were investigated by high-resolution transmission electron microscopy. In a N2 + 10 pct H2 gas atmosphere with a dew point (DP) ranging from 213 K to 278 K (-60 °C to 5 °C), a continuous layer of selective oxides was formed on the surface. Annealing in a higher DP gas atmosphere resulted in a thinner layer of external oxidation and a greater depth of internal oxidation. The hot dipping was carried out in a Zn bath containing 0.22 mass pct Al, and the bath temperature was 733 K (460 °C). Coarse and discontinuous Fe2Al5- x Zn x grains and Fe-Zn intermetallics (ζ and δ) were observed at the steel/coating interface after the hot dip galvanizing (HDG) of panels were annealed in a low DP atmosphere 213 K (-60 °C). The Fe-Zn intermetallics were formed both in areas where the Fe2Al5- x Zn x inhibition layer had not been formed and on top of non-stoichiometric Fe-Al-Zn crystals. Poor wetting was observed on panels annealed in a low DP atmosphere because of the formation of thick film-type oxides on the surface. After annealing in higher DP gas atmospheres, i.e., 263 K and 278 K (-10 °C and 5 °C), a continuous and fine-grained Fe2Al5- x Zn x layer was formed. No Fe-Zn intermetallics were formed. The small grain size of the inhibition layer was attributed to the nucleation of the Fe2Al5- x Zn x grains on small ferrite sub-surface grains and the presence of granular surface oxides. A high DP atmosphere can therefore significantly contribute to the decrease of Zn-coating defects on CMnSi TRIP steels processed in HDG lines.

Study on the Formation of Reaction Phase to Si Addition in Boron Steel Hot-Dipped in Al–7Ni Alloy

Directory of Open Access Journals (Sweden)

Jung-Gil Yun

2017-11-01

Full Text Available In order to reduce the intermetallic compounds formed during the application of an Al–7Ni wt % hot-dip multifunctional coating on boron steel, developed for Tailor Welded Blanks (TWB and hot stamping, 2–6 wt % Si was added to the coating to change the reaction layer. The coating was run at 690 °C for 120 s. Al9FeNi phases were formed on the steel interface, Fe2Al5 was formed on the steel, FeAl3 was generated between the existing layers, and flake-type Al2Fe3Si3 was formed in the Fe2Al5 phase, depending on the Si content. In addition, as Si was added to the coating, the thickness of the Fe2Al5 phase decreased and the thickness of the Al9FeNi phase and Al2Fe3Si3 increased. The decrease in the thickness of the Fe2Al5 phase was mainly due to the effect of the Si solid solution and the Al2Fe3Si3 formation in the Fe2Al5 phase. The reason for the growth of Al9FeNi is that the higher the Si content in the coating, the more the erosion of the interface of the steel material due to the coating solution. Therefore, the outflow of Fe into the coating liquid increased.

A study of the influence of air-knife tilting on coating thickness in hot-dip galvanizing

Science.gov (United States)

Cho, Tae-Seok; Kwon, Young-Doo; Kwon, Soon-Bum

2009-09-01

Gas wiping is a decisive operation in hot-dip galvanizing process. In special, it has a crucial influence on the thickness and uniformity in coating film, but may be subsequently responsible for the problem of splashing. The progress of industry demands continuously the reduction of production costs which may relate directly with the increase of coating speed, and the speed up of coating results in the increase of stagnation pressure in gas wiping system in final. It is known that the increase of stagnation pressure may accompany a harmful problem of splashing in general. Together with these, also, from the view point of energy consumption, it is necessary to design a nozzle optimally. And there is known that the downward tilting of nozzle using in air knife system is effective to prevent in somewhat the harmful problem of splashing. In these connections, first, we design a nozzle with constant expansion rate. Next, for the case of actual coating conditions in field, the effects of tilting of the constant expansion rate nozzle are investigated by numerical analysis. Under the present numerical conditions, it was turned out that the nozzle of constant expansion rate of p = having a downward jet angle of 5° is the most effective to diminish the onset of splashing, while the influence of small tilting of the nozzle on impinging wall pressure itself is not so large.

Effects of Mn addition on the microstructure and indentation creep behavior of the hot dip Zn coating

International Nuclear Information System (INIS)

Wang, Youbin; Zeng, Jianmin

2015-01-01

Highlights: • Mn addition could significantly refine the grain of the Zn coating. • Twins could be observed in the Zn coatings. • The stress exponent of the Zn coating increases with Mn addition. • The creep process of the Zn coating is dominated by dislocation climb and twins. - Abstract: The Zn coatings with different Mn additions were prepared by hot dip process, and the effects of the Mn addition on the microstructure and indentation creep behavior of the coatings were investigated through scanning electron microscope and constant-load holding indentation technique at the room temperature. Some twins can be observed in the microstructure of Zn coating, which may account for the formation of the large thermal misfit stress between the zinc coating and the steel substrate. The amount of twin microstructure in the Zn coating decreases with the Mn addition. It is also found that Mn addition could induce MnZn 13 phases to precipitate along the grain boundary and significantly refine the grains of Zn coatings. The steady-state stress of the Zn coating could be improved by Mn addition. The creep stress exponent values are in the range of 14–46 and increases with Mn addition. The creep process of the Zn coating is dominated by dislocation climb and twin formation

The effects of RE and Si on the microstructure and corrosion resistance of Zn–6Al–3Mg hot dip coating

International Nuclear Information System (INIS)

Li, Shiwei; Gao, Bo; Yin, Shaohua; Tu, Ganfeng; Zhu, Guanglin; Sun, Shuchen; Zhu, Xiaoping

2015-01-01

Highlights: • ZAM coating has been prepared by using an experimental hot-dip galvanizing simulator. • The corrosion resistance of ZAM coating can be improved by additions of Si and RE. • Zn–6Al–3Mg–Si–RE coating forms a dense and stabilized corrosion product layer. • Zn–6Al–3Mg–Si–RE coating shows uniform corrosion. - Abstract: The effects of Si and RE on the microstructure and corrosion resistance of Zn–6Al–3Mg coating (ZAM) have been investigated. Surface morphology observations of the coating and corrosion products reveal that the additions of Si and rare earth metals (RES) improve the microstructural homogeneity of ZAMSR coating and stability of corrosion products formed on ZAMSR coating. Moreover, only uniform corrosion occurs in ZAMSR coating during the corrosion test, while intergranular corrosion and pitting occur in ZAM. As a result, the corrosion resistance of ZAM coating is improved by the additions of Si and RES.

The effects of RE and Si on the microstructure and corrosion resistance of Zn–6Al–3Mg hot dip coating

Energy Technology Data Exchange (ETDEWEB)

Li, Shiwei [State Key Laboratory of Complex Nonferrous Metal Resources Clean Utilization, Kunming University of Science and Technology, Kunming 650093 (China); School of Materials and Metallurgy, Northeastern University, Shenyang 110819 (China); Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming 650093 (China); Gao, Bo, E-mail: surfgao@aliyun.com [School of Materials and Metallurgy, Northeastern University, Shenyang 110819 (China); Yin, Shaohua [State Key Laboratory of Complex Nonferrous Metal Resources Clean Utilization, Kunming University of Science and Technology, Kunming 650093 (China); School of Materials and Metallurgy, Northeastern University, Shenyang 110819 (China); Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming 650093 (China); Tu, Ganfeng; Zhu, Guanglin; Sun, Shuchen; Zhu, Xiaoping [School of Materials and Metallurgy, Northeastern University, Shenyang 110819 (China)

2015-12-01

Highlights: • ZAM coating has been prepared by using an experimental hot-dip galvanizing simulator. • The corrosion resistance of ZAM coating can be improved by additions of Si and RE. • Zn–6Al–3Mg–Si–RE coating forms a dense and stabilized corrosion product layer. • Zn–6Al–3Mg–Si–RE coating shows uniform corrosion. - Abstract: The effects of Si and RE on the microstructure and corrosion resistance of Zn–6Al–3Mg coating (ZAM) have been investigated. Surface morphology observations of the coating and corrosion products reveal that the additions of Si and rare earth metals (RES) improve the microstructural homogeneity of ZAMSR coating and stability of corrosion products formed on ZAMSR coating. Moreover, only uniform corrosion occurs in ZAMSR coating during the corrosion test, while intergranular corrosion and pitting occur in ZAM. As a result, the corrosion resistance of ZAM coating is improved by the additions of Si and RES.

Relation between microstructure and adhesion of hot dip galvanized zinc coatings on dual phase steel

International Nuclear Information System (INIS)

Song, G.M.; Vystavel, T.; Pers, N. van der; De Hosson, J.Th.M.; Sloof, W.G.

2012-01-01

Highlights: ► Amorphous manganese oxides present at the steel surface impair the adhesion of the zinc coating. ► The adhesion of the various interfaces that exist in zinc coated steel is quantitatively estimated using the “Macroscopic Atom” model. ► Zinc coating delaminates along the zinc layer/inhibition layer and ζ-FeZn 13 particle/inhibition layer interfaces, which agrees the theoretical calculation. - Abstract: The microstructure of hot dip galvanized zinc coatings on dual phase steel was investigated by electron microscopy and the coating adhesion characterized by tensile testing. The zinc coating consists of a zinc layer and columnar ζ-FeZn 13 particles on top of a thin inhibition layer adjacent to the steel substrate. The inhibition layer is a thin compact and continuous layer that consists of η-Fe 2 Al 5–x Zn x fine and coarse particles. The coarse faceted particles are on top and fine faceted particles are at the bottom. The steel surface is covered with small fraction manganese oxides, which may impair adhesion of the zinc coating. The adhesion at various interfaces that exist in zinc-coated steel was quantitatively estimated using a so-called “macroscopic atom” model. In addition, the adhesion at the interfaces in zinc-coated steel was qualitatively assessed by examining the fracture and delamination behavior upon tensile testing. In accordance with this model, fracture along zinc grain boundaries preceded fracture along the zinc layer/inhibition layer and ζ-FeZn 13 particle/inhibition layer interfaces.

Performance of Flow and Heat Transfer in a Hot-Dip Round Coreless Galvanizing Bath

Science.gov (United States)

Yue, Qiang; Zhang, Chengbo; Xu, Yong; Zhou, Li; Kong, Hui; Wang, Jia

2017-04-01

Flow field in a coreless hot-dip galvanizing pot was investigated through a water modeling experiment. The corresponding velocity vector was measured using an acoustic Doppler velocimeter. The flow field of molten zinc in the bath was also analyzed. Steel strip velocities from 1.7 to 2.7 m/s were adopted to determine the effect of steel strip velocity on the molten zinc flow in the bath. A large vortex filled the space at the right side of the sink roll, under linear speed from 1.0 to 2.7 m/s and width from 1.0 to 1.3 m of the steel strip, because of the effects of wall and shear stress. The results of the water modeling experiment were compared with those of numerical simulations. In the simulation, Maxwell equations were solved using finite element method to obtain magnetic flux density, electromagnetic force, and Joule heating. The Joule heating rate reached the maximum and minimum values near the side wall and at the core of the bath, respectively, because of the effect of skin and proximity. In an industrial-sized model, the molten zinc flow and temperature fields driven by electromagnetic force and Joule heating in the inductor of a coreless galvanizing bath were numerically simulated. The results indicated that the direction of electromagnetic force concentrated at the center of the galvanizing pot horizontal planes and exerted a pinch effect on molten zinc. Consequently, molten zinc in the pot was stirred by electromagnetic force. Under molten zinc flow and electromagnetic force stirring, the temperature of the molten zinc became homogeneous throughout the bath. This study provides a basis for optimizing electromagnetic fields in coreless induction pot and fine-tuning the design of steel strip parameters.

DIP and DIP + 2 as glutathione oxidants and radiation sensitizers in cultured Chinese hamster cells

International Nuclear Information System (INIS)

Harris, J.W.; Power, J.A.; Kosower, N.S.; Kosower, E.M.

1975-01-01

Two diamide analogues, diazene dicarboxylic acid bis (N'-methyl-piperazide) or DIP, and its bis-N'-methyl iodide salt, or DIP + 2, were tested for their ability to penetrate cultured Chinese hamster cells and oxidize intracellular glutathione. DIP penetrated the cells at a reasonable rate at 18 0 C, 160 nmoles being required to oxidize the endogenous glutathione of 2 x 10 6 cells, but it penetrated very slowly at 0 0 C. DIP + 2 did not effectively oxidize glutathione in Chinese hamster cells, possibly because it did not enter the cels. DIP became toxic after about 10 min of exposure, but its toxicity could be moderated by using anoxic conditions. DIP, but not DIP + 2, sensitized anoxic Chinese hamster cells to X-radiation by a factor of 1.5, an effect that was due entirely to removal of the shoulder from the survival curve. (author)

Dips spacecraft integration issues

International Nuclear Information System (INIS)

Determan, W.R.; Harty, R.B.

1988-01-01

The Department of Energy, in cooperation with the Department of Defense, has recently initiated the dynamic isotope power system (DIPS) demonstration program. DIPS is designed to provide 1 to 10 kW of electrical power for future military spacecraft. One of the near-term missions considered as a potential application for DIPS was the boost surveillance and tracking system (BSTS). A brief review and summary of the reasons behind a selection of DIPS for BSTS-type missions is presented. Many of these are directly related to spacecraft integration issues; these issues will be reviewed in the areas of system safety, operations, survivability, reliability, and autonomy

75 FR 17162 - Dipping and Coating Operations (Dip Tanks) Standard; Extension of the Office of Management and...

Science.gov (United States)

2010-04-05

...] Dipping and Coating Operations (Dip Tanks) Standard; Extension of the Office of Management and Budget's... Standard on Dipping and Coating Operations (Dip Tanks) (29 CFR 1910.126(g)(4)). DATES: Comments must be... of efforts in obtaining information (29 U.S.C. 657). The Standard on Dipping and Coating Operations...

A novel method of utilization of hot dip galvanizing slag using the heat waste from itself for protection from radiation.

Science.gov (United States)

Dong, Mengge; Xue, Xiangxin; Kumar, Ashok; Yang, He; Sayyed, M I; Liu, Shan; Bu, Erjun

2018-02-15

A novel, unconventional, low cost, eco-friendly and effective shielding materials have been made utilizing the hot dip galvanizing slag using the heat waste from itself, thereby saving the natural resources and preventing the environmental pollution. SEM-EDS of shielding materials indicates that the other elements are distributed in Zn element. The mass attenuation properties of shielding materials were measured using a narrow beam geometrical setup at 0.662MeV, 1.17MeV and 1.33MeV. The half value thickness layer, effective atomic number, and electron density were used to analyze the shielding performance of the materials. The EBFs and EABFs for the prepared shielding materials were also studied with incident photon energy for penetration depths upto 40mfp. The shielding effectiveness has been compared with lead, iron, zinc, some standard shielding concretes, different glasses and some alloys. The shielding effectiveness of the prepared samples is almost found comparable to iron, zinc, selected alloys and glasses while better than some standard shielding concretes. In addition, it is also found that the bending strength of all shielding materials is more than 110MPa. Copyright © 2017 Elsevier B.V. All rights reserved.

DIPS space exploration initiative safety

International Nuclear Information System (INIS)

Dix, T.E.

1991-01-01

The Dynamic Isotope Power Subsystem has been identified for potential applications for the Space Exploration Initiative. A qualitative safety assessment has been performed to demonstrate the overall safety adequacy of the Dynamic Isotope Power Subsystem for these applications. Mission profiles were defined for reference lunar and martian flights. Accident scenarios were qualitatively defined for all mission phases. Safety issues were then identified. The safety issues included radiation exposure, fuel containment, criticality, diversion, toxic materials, heat flux to the extravehicular mobility unit, and disposal. The design was reviewed for areas where safety might be further improved. Safety would be improved by launching the fuel separate from the rest of the subsystem on expendable launch vehicles, using a fuel handling tool during unloading of the hot fuel canister, and constructing a cage-like structure around the reversible heat removal system lithium heat pipes. The results of the safety assessment indicate that the DIPS design with minor modifications will produce a low risk concept

Review of Langmuir-Wave-Caused Dips and Charge-Exchange-Caused Dips in Spectral Lines from Plasmas and their Applications

Directory of Open Access Journals (Sweden)

Elisabeth Dalimier

2014-05-01

Full Text Available We review studies of two kinds of dips in spectral line profiles emitted by plasmas—dips that have been predicted theoretically and observed experimentally: Langmuir-wave-caused dips (L-dips and charge-exchange-caused dips (X-dips. There is a principal difference with respect to positions of L-dips and X-dips relative to the unperturbed wavelength of a spectral line: positions of L-dips scale with the electron density Ne roughly as Ne1/2, while positions of X-dips are almost independent of Ne (the dependence is much weaker than for L-dips. L-dips and X-dips phenomena are important, both fundamentally and practically. The fundamental importance is due to a rich physics behind each of these phenomena. L-dips are a multi-frequency resonance phenomenon caused by a single-frequency (monochromatic electric field. X-dips are due to charge exchange at anticrossings of terms of a diatomic quasi-molecule, whose nuclei have different charges. As for important practical applications, they are as follows: observations of L-dips constitute a very accurate method to measure the electron density in plasmas—a method that does not require knowledge of the electron temperature. L-dips also allow measuring the amplitude of the electric field of Langmuir waves—the only spectroscopic method available for this purpose. Observations of X-dips provide an opportunity to determine rate coefficient of charge exchange between multi-charged ions. This is an important reference data, virtually inaccessible by other experimental methods. The rate coefficients of charge exchange are important for magnetic fusion in Tokamaks, for population inversion in the soft x-ray and VUV ranges, for ion storage devices, as well as for astrophysics (e.g., for the solar plasma and for determining the physical state of planetary nebulae.

Ultrasonic dip seal maintenance system

International Nuclear Information System (INIS)

Poindexter, A.M.; Ricks, H.E.

1978-01-01

Disclosed is a system for removing impurities from the surfaces of liquid dip seals and for wetting the metal surfaces of liquid dip seals in nuclear components. The system comprises an ultrasonic transducer that transmits ultrasonic vibrations along an ultrasonic probe to the metal and liquid surfaces of the dip seal thereby loosening and removing those impurities

Examination of the Mg-Zn phase formation in hot-dip galvanized steel sheet; Untersuchung der Mg-Zn-Phasenbildung in feuerverzinktem Stahlblech

Energy Technology Data Exchange (ETDEWEB)

Zywitzki, Olaf; Modes, Thomas; Scheffel, Bert; Metzner, Christoph [Fraunhofer-Institut fuer Elektronenstrahl- und Plasmatechnik, Dresden (Germany)

2012-07-01

Zinc-magnesium layers have been produced by a combination of conventional hot-dip galvanizing and PVD magnesium coating. A subsequent short heat treatment causes the diffusion of magnesium into the zinc layer. The influence of the maximum temperature of the heat treatment on the diffusion of magnesium and on the type and distribution of the formed intermetallic Mg-Zn phases has been examined in detail in a temperature range from 300 to 400 C by means of X-ray phase analyses and metallographic cross sections. With increasing temperature a sequential intermetallic Mg-Zn phase formation has been detected. At 300 C, an initial magnesium rich, intermetallic MgZn{sub 2} surface layer is formed, which, at higher temperatures from 335 to 379 C, is progressively transformed into a zinc rich Mg{sub 2}Zn{sub 11} layer by interdiffusion. In this context, the nucleation of the Mg{sub 2}Zn{sub 11} phase takes place on the interface between the MgZn{sub 2} and the Zn phase. Above the peritectic temperature of 381 C, the microstructure is composed of a zinc matrix in which precipitated MgZn{sub 2} is dispersed. (orig.)

A suggestion of a new method for the calculation of the coating thickness in continuous hot-dip galvanizing

Energy Technology Data Exchange (ETDEWEB)

Jo, C. M.; Kwon, Y. D.; Kwon, S. B. [Kyungpook National University, Daegu (Korea, Republic of); Kim, G. Y. [POSCO Technical Research laboratories, Gumgo-dong (Korea, Republic of)

2011-11-15

It is known that the distributions of the impinging pressure gradient and the shear stress at the strip surface play a decisive key role in the decision of the coating thickness in hot-dip galvanizing. So, to predict the exact coating thickness, it is essential that the distributions of the impinging wall jet pressure and the shear stress acting between the liquid film and jet stream are measured (or calculated) exactly for each specific coating condition. So far, to obtain the impinging wall jet pressure, it was assumed that the jet issuing from an air-knife is similar to the Hiemenz plane stagnation flow, and the wall shear stress could be predicted by an equation using the assumption of a non-negative Gaussian profile in impinging wall jet pressure in general, so that it cannot be reliable for some impinging wall jet regions and nozzle systems intrinsically. Nevertheless, one cannot find a suitable method to cope with the difficulties in measuring/calculating of the shear stress and the impinging wall jet pressure. Such a difficulty which will cause an inaccuracy in the coating thickness prediction. With these connections, in the present study, we suggest a new method named as a two-step calculation method to calculate the final coating thickness, which consists of the air jet analysis and coating thickness calculation. And, from the comparison of the results one may confirm the validation of the new suggested method.

9 CFR 72.25 - Dipping methods.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Dipping methods. 72.25 Section 72.25 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... CATTLE § 72.25 Dipping methods. Dipping is accomplished by thoroughly wetting the entire skin by either...

k0-NAA applied to certified reference materials and hair samples. Evaluation of exposure level in a galvanising industry

International Nuclear Information System (INIS)

Menezes, M.A. de B.C.; Pereira Maia, E.C.

2000-01-01

The k 0 parametric neutron activation analysis has been applied since 1995 in the Radiochemical Sector/CDTN, Belo Horizonte, Brazil. Several certified reference materials were studied with the aim of analysing biological samples. This work is related to an IAEA co-ordinated research project whose goal is to make a survey of the exposures to metals related to occupational diseases. It has been conducted by CDTN and government departments of health. The hair samples as bioindicators were donated by galvanising factory workers in Belo Horizonte. This city and surrounding area are important industrial centres and that industry is responsible for the majority of patients who look for medical assistance because of metal contamination. The Al, Co, Cu, Cr, La, Mn, Sb and V concentrations determined in the workers' samples suggest endogenous contamination. (author)

Overall model of the dynamic behaviour of the steel strip in an annealing heating furnace on a hot-dip galvanizing line

Energy Technology Data Exchange (ETDEWEB)

Martinez-de-Pison, F.J.; Pernia, A.; Jimenez-Macias, E.; Fernandez, R.

2010-07-01

Predicting the temperature of the steel strip in the annealing process in a hot-dip galvanizing line (HDGL) is important to ensure the physical properties of the processed material. The development of an accurate model that is capable of predicting the temperature the strip will reach according to the furnaces variations in temperature and speed, its dimensions and the steels chemical properties, is a requirement that is being increasingly called for by industrial plants of this nature. This paper presents a comparative study made between several types of algorithms of Data Mining and Artificial Intelligence for the design of an efficient and overall prediction model that will allow determining the strips variation in temperature according to the physico-chemical specifications of the coils to be processed, and fluctuations in temperature and speed that are recorded within the annealing process. The ultimate goal is to find a model that is effectively applicable to coils of new types of steel or sizes that are being processed for the first time. This model renders it possible to fine-tune the control model in order to standardise the treatment in areas of the strip in which there is a transition between coils of different sizes or types of steel. (Author).

Evaluation of treatments with hot water, chemicals and ventilated containers to reduce microbial spoilage in irradiated potatoes

International Nuclear Information System (INIS)

Shirsat, S.G.; Thomas, P.; Nair, P.M.

1991-01-01

Potatoes irradiated to control sprouting were dipped in: hot water (56°C, 5 min; 52°C, 10, 15 and 20 min); cold (25°C, 5 min) or hot (56°C, 5 min) salicylic acid (1000 and 2000 ppm); or sodium hypochlorite (0.1 and 0.2%, 5 min); or dusted with salicylic acid (1 and 2%), to try to reduce the incidence of bacterial soft rot (Erwinia sp.) during controlled temperature (10°C, 15°C) and ambient temperature (20–34°C) storage. All treatments, particularly hot water and hot salicylic acid dip, increased microbial spoilage, possibly as a result of handling damage during the treatments combined with the inhibition of wound periderm formation as a result of irradiation. Storing irradiated tubers in well ventilated containers reduced soft rot compared to storing them in sacks and after 6 months storage at 10, 15 and 20–34°C, 95, 90 and 77% respectively were healthy and marketable. (author)

Role of Al in Zn bath on the formation of the inhibition layer during hot-dip galvanizing for a 1.2Si-1.5Mn transformation-induced plasticity steel

Science.gov (United States)

Wang, Kuang-Kuo; Hsu, Chiung-Wen; Chang, Liuwen; Gan, Dershin; Yang, Kuo-Cheng

2013-11-01

This study investigated the interaction between the Al in the Zn bath and the surface oxides formed by selective oxidation on a 1.2Si-1.5Mn TRIP steel during hot-dip galvanizing. XPS and TEM were employed for characterization. The results indicated that the amorphous xMnO·SiO2 oxide could react with Al to form a Si-Mn-Al-containing oxide. The crystalline MnSiO3 and Mn2SiO4 oxides could be largely reduced by Al to form holes in the oxide film. Consequently, the steel covered by a layer of mixed xMnO·SiO2 and MnSiO3 could form a continuous Fe2Al5 inhibition layer and showed the highest galvanizability among the three samples examined.

A review of hot cracking in austenitic stainless steel weldments

International Nuclear Information System (INIS)

Shankar, V.; Gill, T.P.S.; Mannan, S.L.; Rodriguez, P.

1991-01-01

The occurrence of hot cracking in austenitic stainless steel weldments is discussed with respect to its origin and metallurgical contributory factors. Of the three types of hot cracking, namely solidification cracking, liquation and ductility dip cracking, solidification cracking occurs in the interdendritic regions in weld metal while liquation and ductility dip cracking occur intergranularly in the heat-affected zone (HAZ). Segregation of impurity and minor elements such as sulphur, phosphorous, silicon, niobium, boron etc to form low melting eutectic phases has been found to be the major cause of hot cracking. Control of HAZ cracking requires minimisation of impurity elements in the base metal. In stabilized stainless steels containing niobium, higher amounts of delta-ferrite have been found necessary to prevent cracking than in unstabilized compositions. Titanium compounds have been found to cause liquation cracking in maraging steels and titanium containing stainless steels and superalloys. In nitrogen added stainless steels, cracking resistance decreases when the solidification mode changes to primary austenitic due to nitrogen addition. A review of the test methods to evaluate hot cracking behaviour showed that several external restraint and semi-self-restraint tests are available. The finger Test, WRC Fissure Bend Test, the PVR test and the Varestraint Test are described along with typical test results. Hot ductility testing to reveal HAZ cracking tendency during welding is described, which is of particular importance to stabilized stainless steels. Based on the literature, recommendations are made for welding stabilized and nitrogen added steels, indicating areas of further work. (author). 81 refs., 30 figs., 1 tab

Mantle wedge serpentinization effects on slab dips

Directory of Open Access Journals (Sweden)

Eh Tan

2017-01-01

Full Text Available The mechanical coupling between a subducting slab and the overlying mantle wedge is an important factor in controlling the subduction dip angle and the flow in mantel wedge. This paper investigates the role of the amount of mantle serpentinization on the subduction zone evolution. With numerical thermos-mechanical models with elasto-visco-plastic rheology, we vary the thickness and depth extent of mantle serpentinization in the mantle wedge to control the degree of coupling between the slab and mantle wedge. A thin serpentinized mantle layer is required for stable subduction. For models with stable subduction, we find that the slab dip is affected by the down-dip extent and the mantle serpentinization thickness. A critical down-dip extent exists in mantle serpentinization, determined by the thickness of the overriding lithosphere. If the down-dip extent does not exceed the critical depth, the slab is partially coupled to the overriding lithosphere and has a constant dip angle regardless of the mantle serpentinization thickness. However, if the down-dip extent exceeds the critical depth, the slab and the base of the overriding lithosphere would be separated and decoupled by a thick layer of serpentinized peridotite. This allows further slab bending and results in steeper slab dip. Increasing mantle serpentinization thickness will also result in larger slab dip. We also find that with weak mantle wedge, there is no material flowing from the asthenosphere into the serpentinized mantle wedge. All of these results indicate that serpentinization is an important ingredient when studying the subduction dynamics in the mantle wedge.

Two-colour dip spectroscopy of jet-cooled molecules

Science.gov (United States)

Ito, Mitsuo

In optical-optical double resonance spectroscopy, the resonance transition from an intermediate state to a final state can be detected by a dip of the signal (fluorescence or ion) associated with the intermediate state. This method probing the signal of the intermediate state may be called `two-colour dip spectroscopy'. Various kinds of two-colour dip spectroscopy such as two-colour fluorescence/ion dip spectroscopy, two-colour ionization dip spectroscopy employing stimulated emission, population labelling spectroscopy and mass-selected ion dip spectroscopy with dissociation were briefly described, paying special attention to their characteristics in excitation, detection and application. They were extensively and successfully applied to jet-cooled large molecules and provided us with new useful information on the energy and dynamics of excited molecules.

40 CFR 420.120 - Applicability; description of the hot coating subcategory.

Science.gov (United States)

2010-07-01

... works resulting from the operations in which steel is coated with zinc, terne metal, or other metals by the hot dip process, and those rinsing operations associated with that process. (b) The BPT and BAT... facilities achieving, during periods of normal production, zinc discharge levels more stringent than those...

ICE-DIP kicks off

CERN Multimedia

CERN Bulletin

2013-01-01

Last month, Marie Curie Actions* added a new member to its ranks: ICE-DIP (the Intel-CERN European Doctorate Industrial Program). The programme held its kick-off meeting on 18-19 February in Leixlip near Dublin, Ireland, at Intel’s premises.   Building on CERN’s long-standing relationship with Intel in the CERN openlab project, ICE-DIP brings together CERN and industrial partners, Intel and Xena Networks, to train five Early Stage ICT Researchers. These researchers will be funded by the European Commission and granted a CERN Fellow contract while enrolled in the doctoral programmes at partner universities Dublin City University and National University of Ireland Maynooth. The researchers will go on extended secondments to Intel Labs Europe locations across Europe during their three-year training programme. The primary focus of the ICE-DIP researchers will be the development of techniques for acquiring and processing data that are relevant for the trigger a...

Expression Patterns and Potential Biological Roles of Dip2a.

Directory of Open Access Journals (Sweden)

Luqing Zhang

Full Text Available Disconnected (disco-interacting protein 2 homolog A is a member of the DIP2 protein family encoded by Dip2a gene. Dip2a expression pattern has never been systematically studied. Functions of Dip2a in embryonic development and adult are not known. To investigate Dip2a gene expression and function in embryo and adult, a Dip2a-LacZ mouse model was generated by insertion of β-Gal cDNA after Dip2a promoter using CRISPR/Cas9 technology. Dip2a-LacZ mouse was designed to be a lacZ reporter mouse as well as a Dip2a knockout mouse. Heterozygous mice were used to study endogenous Dip2a expression and homozygotes to study DIP2A-associated structure and function. LacZ staining indicated that Dip2a is broadly expressed in neuronal, reproductive and vascular tissues, as well as in heart, kidney, liver and lung. Results demonstrate that Dip2a is expressed in ectoderm-derived tissues in developing embryos. Adult tissues showed rich staining in neurons, mesenchymal, endothelial, smooth muscle cells and cardiomyocytes by cell types. The expression pattern highly overlaps with FSTL1 and supports previous report that DIP2A to be potential receptor of FSTL1 and its protective roles of cardiomyocytes. Broad and intense embryonic and adult expression of Dip2a has implied their multiple structural and physiological roles.

Evolution of micro-arc oxidation behaviors of the hot-dipping aluminum coatings on Q235 steel substrate

International Nuclear Information System (INIS)

Lu Lihong; Shen Dejiu; Zhang Jingwu; Song Jian; Li Liang

2011-01-01

Micro-arc oxidation (MAO) is not applicable to prepare ceramic coatings on the surface of steel directly. In this work, hybrid method of MAO and hot-dipping aluminum (HDA) were employed to fabricate composite ceramic coatings on the surface of Q235 steel. The evolution of MAO coatings, such as growth rate, thickness of the total coatings, ingrown and outgrown coatings, cross section and surface morphologies and phase composition of the ceramic coatings were studied. The results indicate that both the current density and the processing time can affect the total thickness, the growth rate and the ratio of ingrown and outgrown thickness of the ceramic coatings. The total thickness, outgrown thickness and growth rate have maximum values with the processing time prolonged. The time when the maximum value appears decreases and the ingrown dominant turns to outgrown dominant little by little with the current density increasing. The composite coatings obtained by this hybrid method consists of three layers from inside to outside, i.e. Fe-Al alloy layer next to the substrate, aluminum layer between the Fe-Al layer and the ceramic coatings which is as the top exterior layer. Metallurgical bonding was observed between every of the two layers. There are many micro-pores and micro-cracks, which act as discharge channels and result of quick and non-uniform cooling of melted sections in the MAO coatings. The phase composition of the ceramic coatings is mainly composed of amorphous phase and crystal Al 2 O 3 oxides. The crystal Al 2 O 3 phase includes κ-Al 2 O 3 , θ-Al 2 O 3 and β-Al 2 O 3 . Compared with the others, the β-Al 2 O 3 content is the least. The MAO process can be divided into three periods, namely the common anodic oxidation stage, the stable MAO stage and the ceramic coatings destroyed stage. The exterior loose part of the ceramic coatings was destroyed badly in the last period which should be avoided during the MAO process.

A Case Study Of Turkish Transmission System For VoltageDips

DEFF Research Database (Denmark)

Inan, E.; Alboyaci, B.; Bak, Claus Leth

2009-01-01

Power quality problems usually appear in the form of voltage sags, transients and harmonics. From these three broad categories of power quality problems, voltage dips account the most disturbances experienced by industrial customers. Voltage dips generally refer to instantaneous short-duration vo......Power quality problems usually appear in the form of voltage sags, transients and harmonics. From these three broad categories of power quality problems, voltage dips account the most disturbances experienced by industrial customers. Voltage dips generally refer to instantaneous short...... analysis of voltage dip performance of the whole transmission system, is used to compare with results constructed fault statics from SIMPOW DIPS analysis program real data. SIMPOW DIPS software enables to calculate dip frequency for all busses and lines....

Attenuation of pressure dips underneath piles of spherocylinders.

Science.gov (United States)

Zhao, Haiyang; An, Xizhong; Gou, Dazhao; Zhao, Bo; Yang, Runyu

2018-05-30

The discrete element method (DEM) was used to simulate the piling of rod-like (elongated sphero-cylindrical) particles, mainly focusing on the effect of particle shape on the structural and force properties of the piles. In this work, rod-like particles of different aspect ratios were discharged on a flat surface to form wedge-shaped piles. The surface properties of the piles were characterized in terms of angle of repose and stress at the bottom of the piles. The results showed that the rise of the angle of repose became slower with the increase of particle aspect ratio. The pressure dip underneath the piles reached the maximum when the particle aspect ratio was around 1.6, beyond which the pressure dip phenomenon became attenuated. Both the pressure dip and the shear stress dip were quantitatively examined. The structure and forces inside the piles were further analyzed to understand the change in pressure dip, indicating that "bridging" or "arching" structures within the piles were the cause of the pressure dip.

Effect of gamma irradiation combined with hot water treatment on the texture, pulp color and sensory quality of ''Nahng Glahng Wahn'' mangoes

International Nuclear Information System (INIS)

Lacroix, M.; Jobin, M.; Beliveau, M.; Gagnon, M.

1992-01-01

Mangoes (Mangifera indica L.) from Thailand of the 'Nahng Glahng Wahn' variety were irradiated with a 60 Co source at a dose of 0.63 kGy and a dose rate of 9.23 kGy/hr, with or without a hot water treatment prior to irradiation. The irradiation treatment had little effect on the texture and preserved the yellow color in the pulp. Test of sensory evaluation revealed that irradiated mango pulp was preferred for overall appearance, taste, texture and palatability. The appearance of whole irradiated mangoes was also preferred over that of the control mangoes. However, no significant differences were observed between irradiated and hot water dipped irradiated mangoes for all characteristics studied in mangoes pulp. The results showed that these treatments (hot water dip plus irradiation or irradiation alone) are useful and non-destructive methods to preserve consumer acceptability

Cattle dipping practices in the Philippines and the degradation of coumaphos in a simulated cattle dip

International Nuclear Information System (INIS)

Calumpang, S.M.F.; Medina, M.J.B.; Tejada, A.W.

1997-01-01

A survey of cattle dip facilities and current practices employed was done. Coumaphos and ethion were the commonly used acaricides in the four respondent stock farms. The behavior of coumaphos in a simulated model cattle dip was monitored using radiotracer techniques. Degradation was rapid, resulting in the formation of potasan metabolite and bound residues in the sediment. A rapid field method for the detection of organophosphate pesticides was used in monitoring the degradation of coumaphos in a cattle dip. The sensitivity of the method is comparable to the conventional HPLC method employed. This rapid field method can easily be used by cattle ranch owners to monitor coumaphos content of the vat facility so that recharging could be made in order to prevent the onset of resistance development in cattle tick. (author)

Fabrication of tubed functionally graded material by slurry dipping process. Thickness control of dip-coated layer

International Nuclear Information System (INIS)

Watanabe, Ryuzo

1997-03-01

In order to obtain long life fuel cladding tubes for the fast breeder reactor, the concept of functionally graded material was applied for the material combination of Molybdenum/stainless steel/Titanium, in which Titanium and Molybdenum were placed at the inner and outer sides, respectively. Slurry dipping method was employed because of its capability of shape forming and microstructural control. We have hitherto reported the design criteria for the graded layers, preparation of the slurry, and microstructural control of the dip-coated layers. In the present report, the thickness control of the dip-coated layer is described in detail. The thickness of the dip-coated layer depends primarily on the viscosity of the slurry. Nevertheless, for the stable dispersion of the powder in the slurry, which dominates the microstructural homogeneity, an optimum viscosity value is present for the individual slurries. With stable slurries of Ti, Mo, stainless steel powders and their mixtures, the thicknesses of dip-coated layers were controlled in dependence of their viscosities and yield values. For Ti and stainless steel powders and their mixture a PAANa was used as a dispersing agent. A NaHMP was found to be effective for the dispersion of Mo powder and Mo/stainless steel powder mixture. For all slurries tested in the present investigation PVA addition was helpful for the viscosity control. Dip-coating maps have been drawn for the stabilization of the slurries and for the formation of films with a sufficient strength for further manipulation for the slurries with low viscosity (∼10 mPa s). The final film thickness for the low-viscosity slurry with the optimum condition was about 200 μm. The slurries with high viscosities of several hundreds mPa s had a good stability and the yield value was easy to be controlled. The film thickness was able to be adjusted in the size range between several tens and several hundreds μm. The final thickness of the graded layer was determined

Evolution of micro-arc oxidation behaviors of the hot-dipping aluminum coatings on Q235 steel substrate

Energy Technology Data Exchange (ETDEWEB)

Lu Lihong, E-mail: llh_qc@163.com [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China) and Research Department, The Chinese People' s Armed Police Academy, Langfang 065000 (China); Shen Dejiu; Zhang Jingwu [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Song Jian; Li Liang [Tsinghua University, State Key Laboratory of Automotive Safety and Energy, Beijing 100084 (China)

2011-02-15

Micro-arc oxidation (MAO) is not applicable to prepare ceramic coatings on the surface of steel directly. In this work, hybrid method of MAO and hot-dipping aluminum (HDA) were employed to fabricate composite ceramic coatings on the surface of Q235 steel. The evolution of MAO coatings, such as growth rate, thickness of the total coatings, ingrown and outgrown coatings, cross section and surface morphologies and phase composition of the ceramic coatings were studied. The results indicate that both the current density and the processing time can affect the total thickness, the growth rate and the ratio of ingrown and outgrown thickness of the ceramic coatings. The total thickness, outgrown thickness and growth rate have maximum values with the processing time prolonged. The time when the maximum value appears decreases and the ingrown dominant turns to outgrown dominant little by little with the current density increasing. The composite coatings obtained by this hybrid method consists of three layers from inside to outside, i.e. Fe-Al alloy layer next to the substrate, aluminum layer between the Fe-Al layer and the ceramic coatings which is as the top exterior layer. Metallurgical bonding was observed between every of the two layers. There are many micro-pores and micro-cracks, which act as discharge channels and result of quick and non-uniform cooling of melted sections in the MAO coatings. The phase composition of the ceramic coatings is mainly composed of amorphous phase and crystal Al{sub 2}O{sub 3} oxides. The crystal Al{sub 2}O{sub 3} phase includes {kappa}-Al{sub 2}O{sub 3}, {theta}-Al{sub 2}O{sub 3} and {beta}-Al{sub 2}O{sub 3}. Compared with the others, the {beta}-Al{sub 2}O{sub 3} content is the least. The MAO process can be divided into three periods, namely the common anodic oxidation stage, the stable MAO stage and the ceramic coatings destroyed stage. The exterior loose part of the ceramic coatings was destroyed badly in the last period which should be

E-Cigs, Menthol & Dip

Science.gov (United States)

... Close Search × MENU BACK CLOSE SMOKEFREE.GOV HOME E-Cigs, Menthol & Dip There are many types of tobacco products. Learn how e-cigarettes, menthol cigarettes, smokeless tobacco, and other products ...

Destructive role of hot ions in the formation of electrostatic density humps and dips in dusty plasmas

International Nuclear Information System (INIS)

Mahmood, S.; Saleem, H.

2003-01-01

It is shown that the ion thermal energy is destructive for the ion acoustic solitons in the presence of dust, and it decreases the value of Mach number for the formation of solitary structures. The regions of ion density humps and dips are produced simultaneously, corresponding to positive and negative values of the electrostatic potential. The nonlinear electron density also behaves in a similar fashion as that of ions. However, the dust density increases in the regions where the ion and electron densities are depleted and vice versa

Gravity interpretation of dipping faults using the variance analysis method

International Nuclear Information System (INIS)

Essa, Khalid S

2013-01-01

A new algorithm is developed to estimate simultaneously the depth and the dip angle of a buried fault from the normalized gravity gradient data. This algorithm utilizes numerical first horizontal derivatives computed from the observed gravity anomaly, using filters of successive window lengths to estimate the depth and the dip angle of a buried dipping fault structure. For a fixed window length, the depth is estimated using a least-squares sense for each dip angle. The method is based on computing the variance of the depths determined from all horizontal gradient anomaly profiles using the least-squares method for each dip angle. The minimum variance is used as a criterion for determining the correct dip angle and depth of the buried structure. When the correct dip angle is used, the variance of the depths is always less than the variances computed using wrong dip angles. The technique can be applied not only to the true residuals, but also to the measured Bouguer gravity data. The method is applied to synthetic data with and without random errors and two field examples from Egypt and Scotland. In all cases examined, the estimated depths and other model parameters are found to be in good agreement with the actual values. (paper)

Structural Controls of Neal Hot Springs Geothermal Field, Malhuer County, Oregon

Science.gov (United States)

Edwards, J. H.; Faulds, J. E.

2012-12-01

Detailed mapping (1:24,000) of the Neal Hot Springs area (90 km2) in eastern Oregon is part of a larger study of geothermal systems in the Basin and Range, which focuses on the structural controls of geothermal activity. The study area lies within the intersection of two regional grabens, the middle-late Miocene, N-striking, Oregon-Idaho graben and younger late Miocene to Holocene, NW-striking, western Snake River Plain graben. The geothermal field is marked by Neal Hot Springs, which effuse from opaline sinter mounds just north of Bully Creek. Wells producing geothermal fluids, with temperatures at 138°C, intersect a major, W-dipping, NNW-striking, high-angle normal fault at depths of 850-915 m. Displacement along this structure dies southward, with likely horse-tailing, which commonly produces high fracture density and a zone of high permeability conducive for channeling hydrothermal fluids. Mapping reveals that the geothermal resource lies within a local, left step-over. 'Hard-linkage' between strands of the left-stepping normal fault, revealed through a study of well chips and well logs, occurs through two concealed structures. Both are W-striking faults, with one that runs parallel to Cottonwood Creek and one 0.5 km N of the creek. Injection wells intersect these two transverse structures within the step-over. Stepping and displacement continue to the NW of the known geothermal field, along W-dipping, N-striking faults that cut lower to middle Miocene Hog Creek Formation, consisting of silicic and mafic volcanic rocks. These N-striking faults were likely initiated during initial Oregon-Idaho graben subsidence (15.3-15.1 Ma), with continued development through late Miocene. Bully Creek Formation deposits, middle to upper Miocene lacustrine and pyroclastic rocks, concomitantly filled the sub half-grabens, and they dip gently to moderately eastward. Younger, western Snake River Plain deposits, upper Miocene to Pliocene fluvial, lacustrine, and pyroclastic rocks

Comparison of piracetam measured with HPLC-DAD, HPLC-ESI-MS, DIP-APCI-MS, and a newly developed and optimized DIP-ESI-MS.

Science.gov (United States)

Lenzen, Claudia; Winterfeld, Gottfried A; Schmitz, Oliver J

2016-06-01

The direct inlet probe-electrospray ionization (DIP-ESI) presented here was based on the direct inlet probe-atmospheric pressure chemical ionization (DIP-APCI) developed by our group. It was coupled to an ion trap mass spectrometer (MS) for the detection of more polar compounds such as degradation products from pharmaceuticals. First, the position of the ESI tip, the gas and solvent flow rates, as well as the gas temperature were optimized with the help of the statistic program Minitab® 17 and a caffeine standard. The ability to perform quantitative analyses was also tested by using different concentrations of caffeine and camphor. Calibration curves with a quadratic calibration regression of R (2) = 0.9997 and 0.9998 for caffeine and camphor, respectively, were obtained. The limit of detection of 2.5 and 1.7 ng per injection for caffeine and camphor were determined, respectively. Furthermore, a solution of piracetam was used to compare established analytical methods for this drug and its impurities such as HPLC-diode array detector (DAD) and HPLC-ESI-MS with the DIP-APCI and the developed DIP-ESI. With HPLC-DAD and 10 μg piracetam on column, no impurity could be detected. With HPLC-ESI-MS, two impurities (A and B) were identified with only 4.6 μg piracetam on column, while with DIP-ESI, an amount of 1.6 μg piracetam was sufficient. In the case of the DIP-ESI measurements, all detected impurities could be identified by MS/MS studies. Graphical Abstract Scheme of the DIP-ESI principle.

Social support and nocturnal blood pressure dipping: a systematic review.

Science.gov (United States)

Fortmann, Addie L; Gallo, Linda C

2013-03-01

Attenuated nocturnal blood pressure (BP) dipping is a better predictor of cardiovascular disease (CVD) morbidity and mortality than resting BP measurements. Studies have reported associations between social support, variously defined, and BP dipping. A systematic review of the literature was conducted to investigate associations of functional and structural social support with nocturnal BP dipping assessed over a minimum of 24 hours. A total of 297 articles were identified. Of these, 11 met criteria for inclusion; all studies were cross-sectional in design and included adult participants only (mean age = 19 to 72 years). Evidence was most consistent for an association between functional support and BP dipping, such that 5 of 7 studies reported statistically (or marginally) significant positive associations with BP dipping. Statistically significant functional support-BP dipping associations were moderate (standardized effect size (d) = 0.41) to large (d = 2.01) in magnitude. Studies examining structural support were fewer and relatively less consistent; however, preliminary evidence was observed for associations of marital status and social contact frequency with BP dipping. Statistically significant structural support findings were medium (d = 0.53) to large (d = 1.13) in magnitude. Overall, findings suggest a link between higher levels of functional support and greater nocturnal BP dipping; preliminary evidence was also observed for the protective effects of marriage and social contact frequency. Nonetheless, the relatively small number of studies conducted to date and the heterogeneity of findings across meaningful subgroups suggest that additional research is needed to substantiate these conclusions.

Eigenvector of gravity gradient tensor for estimating fault dips considering fault type

Science.gov (United States)

Kusumoto, Shigekazu

2017-12-01

The dips of boundaries in faults and caldera walls play an important role in understanding their formation mechanisms. The fault dip is a particularly important parameter in numerical simulations for hazard map creation as the fault dip affects estimations of the area of disaster occurrence. In this study, I introduce a technique for estimating the fault dip using the eigenvector of the observed or calculated gravity gradient tensor on a profile and investigating its properties through numerical simulations. From numerical simulations, it was found that the maximum eigenvector of the tensor points to the high-density causative body, and the dip of the maximum eigenvector closely follows the dip of the normal fault. It was also found that the minimum eigenvector of the tensor points to the low-density causative body and that the dip of the minimum eigenvector closely follows the dip of the reverse fault. It was shown that the eigenvector of the gravity gradient tensor for estimating fault dips is determined by fault type. As an application of this technique, I estimated the dip of the Kurehayama Fault located in Toyama, Japan, and obtained a result that corresponded to conventional fault dip estimations by geology and geomorphology. Because the gravity gradient tensor is required for this analysis, I present a technique that estimates the gravity gradient tensor from the gravity anomaly on a profile.

Hot electron formation in thermal barrier region of tandem mirror GAMMA 10

International Nuclear Information System (INIS)

Katanuma, I.; Kiwamoto, Y.; Sawada, K.; Miyoshi, S.

1987-01-01

We have studied the hot electron build-up by the second harmonic electron cyclotron resonance heating in the thermal barrier region of tandem mirror GAMMA 10 by using a Fokker-Planck code with self-consistent potential profile taken into account. We have found two phases in the evolution of hot electron population and the potential profile. In the first phase where the RF diffusion is dominant quick increase of the hot electron density and that of the mean energy are observed. No further increase in the mean energy is observed thereafter. The potential is the deepest during the first phase. The second phase starts in the mean-free-time of the pitch angle scattering of hot electrons on cold electrons and ions. In this phase the hot electron population increases in the rate of the pitch angle scattering. The potential dip shallows due to the accumulation of pitch angle scattered passing ions. This observation indicates the necessity of the ion pumping for maintaining the negative potential at the thermal barrier. (author)

Cycle oxidation behavior and anti-oxidation mechanism of hot-dipped aluminum coating on TiBw/Ti6Al4V composites with network microstructure.

Science.gov (United States)

Li, X T; Huang, L J; Wei, S L; An, Q; Cui, X P; Geng, L

2018-04-10

Controlled and compacted TiAl 3 coating was successfully fabricated on the network structured TiBw/Ti6Al4V composites by hot-dipping aluminum and subsequent interdiffusion treatment. The network structure of the composites was inherited to the TiAl 3 coating, which effectively reduces the thermal stress and avoids the cracks appeared in the coating. Moreover, TiB reinforcements could pin the TiAl 3 coating which can effectively improve the bonding strength between the coating and composite substrate. The cycle oxidation behavior of the network structured coating on 873 K, 973 K and 1073 K for 100 h were investigated. The results showed the coating can remarkably improve the high temperature oxidation resistance of the TiBw/Ti6Al4V composites. The network structure was also inherited to the Al 2 O 3 oxide scale, which effectively decreases the tendency of cracking even spalling about the oxide scale. Certainly, no crack was observed in the coating after long-term oxidation due to the division effect of network structured coating and pinning effect of TiB reinforcements. Interfacial reaction between the coating and the composite substrate occurred and a bilayer structure of TiAl/TiAl 2 formed next to the substrate after oxidation at 973 K and 1073 K. The anti-oxidation mechanism of the network structured coating was also discussed.

Width and dip of the southern San Andreas Fault at Salt Creek from modeling of geophysical data

Science.gov (United States)

Langenheim, Victoria; Athens, Noah D.; Scheirer, Daniel S.; Fuis, Gary S.; Rymer, Michael J.; Goldman, Mark R.; Reynolds, Robert E.

2014-01-01

We investigate the geometry and width of the southernmost stretch of the San Andreas Fault zone using new gravity and magnetic data along line 7 of the Salton Seismic Imaging Project. In the Salt Creek area of Durmid Hill, the San Andreas Fault coincides with a complex magnetic signature, with high-amplitude, short-wavelength magnetic anomalies superposed on a broader magnetic anomaly that is at least 5 km wide centered 2–3 km northeast of the fault. Marine magnetic data show that high-frequency magnetic anomalies extend more than 1 km west of the mapped trace of the San Andreas Fault. Modeling of magnetic data is consistent with a moderate to steep (> 50 degrees) northeast dip of the San Andreas Fault, but also suggests that the sedimentary sequence is folded west of the fault, causing the short wavelength of the anomalies west of the fault. Gravity anomalies are consistent with the previously modeled seismic velocity structure across the San Andreas Fault. Modeling of gravity data indicates a steep dip for the San Andreas Fault, but does not resolve unequivocally the direction of dip. Gravity data define a deeper basin, bounded by the Powerline and Hot Springs Faults, than imaged by the seismic experiment. This basin extends southeast of Line 7 for nearly 20 km, with linear margins parallel to the San Andreas Fault. These data suggest that the San Andreas Fault zone is wider than indicated by its mapped surface trace.

The First Post-Kepler Brightness Dips of KIC 8462852

Science.gov (United States)

Boyajian, Tabetha. S.; Alonso, Roi; Ammerman, Alex; Armstrong, David; Asensio Ramos, A.; Barkaoui, K.; Beatty, Thomas G.; Benkhaldoun, Z.; Benni, Paul; Bentley, Rory O.; Berdyugin, Andrei; Berdyugina, Svetlana; Bergeron, Serge; Bieryla, Allyson; Blain, Michaela G.; Capetillo Blanco, Alicia; Bodman, Eva H. L.; Boucher, Anne; Bradley, Mark; Brincat, Stephen M.; Brink, Thomas G.; Briol, John; Brown, David J. A.; Budaj, J.; Burdanov, A.; Cale, B.; Aznar Carbo, Miguel; Castillo García, R.; Clark, Wendy J.; Clayton, Geoffrey C.; Clem, James L.; Coker, Phillip H.; Cook, Evan M.; Copperwheat, Chris M.; Curtis, J. L.; Cutri, R. M.; Cseh, B.; Cynamon, C. H.; Daniels, Alex J.; Davenport, James R. A.; Deeg, Hans J.; De Lorenzo, Roberto; de Jaeger, Thomas; Desrosiers, Jean-Bruno; Dolan, John; Dowhos, D. J.; Dubois, Franky; Durkee, R.; Dvorak, Shawn; Easley, Lynn; Edwards, N.; Ellis, Tyler G.; Erdelyi, Emery; Ertel, Steve; Farfán, Rafael. G.; Farihi, J.; Filippenko, Alexei V.; Foxell, Emma; Gandolfi, Davide; Garcia, Faustino; Giddens, F.; Gillon, M.; González-Carballo, Juan-Luis; González-Fernández, C.; González Hernández, J. I.; Graham, Keith A.; Greene, Kenton A.; Gregorio, J.; Hallakoun, Na’ama; Hanyecz, Ottó; Harp, G. R.; Henry, Gregory W.; Herrero, E.; Hildbold, Caleb F.; Hinzel, D.; Holgado, G.; Ignácz, Bernadett; Ilyin, Ilya; Ivanov, Valentin D.; Jehin, E.; Jermak, Helen E.; Johnston, Steve; Kafka, S.; Kalup, Csilla; Kardasis, Emmanuel; Kaspi, Shai; Kennedy, Grant M.; Kiefer, F.; Kielty, C. L.; Kessler, Dennis; Kiiskinen, H.; Killestein, T. L.; King, Ronald A.; Kollar, V.; Korhonen, H.; Kotnik, C.; Könyves-Tóth, Réka; Kriskovics, Levente; Krumm, Nathan; Krushinsky, Vadim; Kundra, E.; Lachapelle, Francois-Rene; LaCourse, D.; Lake, P.; Lam, Kristine; Lamb, Gavin P.; Lane, Dave; Lau, Marie Wingyee; Lewin, Pablo; Lintott, Chris; Lisse, Carey; Logie, Ludwig; Longeard, Nicolas; Lopez Villanueva, M.; Whit Ludington, E.; Mainzer, A.; Malo, Lison; Maloney, Chris; Mann, A.; Mantero, A.; Marengo, Massimo; Marchant, Jon; Martínez González, M. J.; Masiero, Joseph R.; Mauerhan, Jon C.; McCormac, James; McNeely, Aaron; Meng, Huan Y. A.; Miller, Mike; Molnar, Lawrence A.; Morales, J. C.; Morris, Brett M.; Muterspaugh, Matthew W.; Nespral, David; Nugent, C. R.; Nugent, Katherine M.; Odasso, A.; O’Keeffe, Derek; Oksanen, A.; O’Meara, John M.; Ordasi, András; Osborn, Hugh; Ott, John J.; Parks, J. R.; Rodriguez Perez, Diego; Petriew, Vance; Pickard, R.; Pál, András; Plavchan, P.; Pollacco, Don; Pozo Nuñez, F.; Pozuelos, F. J.; Rau, Steve; Redfield, Seth; Relles, Howard; Ribas, Ignasi; Richards, Jon; Saario, Joonas L. O.; Safron, Emily J.; Sallai, J. Martin; Sárneczky, Krisztián; Schaefer, Bradley E.; Schumer, Clea F.; Schwartzendruber, Madison; Siegel, Michael H.; Siemion, Andrew P. V.; Simmons, Brooke D.; Simon, Joshua D.; Simón-Díaz, S.; Sitko, Michael L.; Socas-Navarro, Hector; Sódor, Á.; Starkey, Donn; Steele, Iain A.; Stone, Geoff; Strassmeier, Klaus G.; Street, R. A.; Sullivan, Tricia; Suomela, J.; Swift, J. J.; Szabó, Gyula M.; Szabó, Róbert; Szakáts, Róbert; Szalai, Tamás; Tanner, Angelle M.; Toledo-Padrón, B.; Tordai, Tamás; Triaud, Amaury H. M. J.; Turner, Jake D.; Ulowetz, Joseph H.; Urbanik, Marian; Vanaverbeke, Siegfried; Vanderburg, Andrew; Vida, Krisztián; Vietje, Brad P.; Vinkó, József; von Braun, K.; Waagen, Elizabeth O.; Walsh, Dan; Watson, Christopher A.; Weir, R. C.; Wenzel, Klaus; Westendorp Plaza, C.; Williamson, Michael W.; Wright, Jason T.; Wyatt, M. C.; Zheng, WeiKang; Zsidi, Gabriella

2018-01-01

We present a photometric detection of the first brightness dips of the unique variable star KIC 8462852 since the end of the Kepler space mission in 2013 May. Our regular photometric surveillance started in 2015 October, and a sequence of dipping began in 2017 May continuing on through the end of 2017, when the star was no longer visible from Earth. We distinguish four main 1%–2.5% dips, named “Elsie,” “Celeste,” “Skara Brae,” and “Angkor,” which persist on timescales from several days to weeks. Our main results so far are as follows: (i) there are no apparent changes of the stellar spectrum or polarization during the dips and (ii) the multiband photometry of the dips shows differential reddening favoring non-gray extinction. Therefore, our data are inconsistent with dip models that invoke optically thick material, but rather they are in-line with predictions for an occulter consisting primarily of ordinary dust, where much of the material must be optically thin with a size scale ≪1 μm, and may also be consistent with models invoking variations intrinsic to the stellar photosphere. Notably, our data do not place constraints on the color of the longer-term “secular” dimming, which may be caused by independent processes, or probe different regimes of a single process.

Database of Interacting Proteins (DIP)

Data.gov (United States)

U.S. Department of Health & Human Services — The DIP database catalogs experimentally determined interactions between proteins. It combines information from a variety of sources to create a single, consistent...

A case study of an erosion control practice: the broad-based dip

Science.gov (United States)

Kevin Bold; Pamela Edwards; Karl Williard

2007-01-01

In 2006, 19 gravel haul roads with broad-based dips within the Monongahela National Forest were examined to determine if those dips adhered to Forest specifications for cut depth and dip outslope. Data on the azimuth, contributing road lengths, slopes of the contributing lengths, landscape position of the dip, and soil texture of the road bed materials also were...

Reduction of teat skin mastitis pathogen loads: differences between strains, dips, and contact times.

Science.gov (United States)

Enger, B D; Fox, L K; Gay, J M; Johnson, K A

2015-02-01

The purpose of these experiments was to (1) assess differences in mastitis pathogen strain sensitivities to teat disinfectants (teat dips), and (2) determine the optimum time for premilking teat dips to remain in contact with teat skin to reduce pathogen loads on teat skin. Two experiments were conducted using the excised teat model. In experiment 1, the differences in mastitis pathogen strain sensitivities to 4 commercially available dips (dip A: 1% H2O2; dip B: 1% chlorine dioxide; dip C: 1% iodophor; and dip D: 0.5% iodophor) were evaluated. Four strains of 11 common mastitis pathogens (Staphylococcus aureus, Streptococcus agalactiae, Mycoplasma bovis, Streptococcus dysgalactiae, Streptococcus uberis, Escherichia coli, Staphylococcus chromogenes, Staphylococcus epidermidis, Staphylococcus hyicus, Staphylococcus xylosus, and Staphylococcus haemolyticus) were tested. In experiment 2, the percentage log reduction of mastitis pathogens (Escherichia coli, Streptococcus uberis, Streptococcus dysgalactiae, Klebsiella species, Staphylococcus chromogenes, Staphylococcus haemolyticus, Staphylococcus xylosus, and Staphylococcus epidermidis) on teat skin with 3 commercially available teat dips: dip A; dip D; and dip E: 0.25% iodophor, using dip contact times of 15, 30, and 45 s, was evaluated. Experiment 1 results indicated significant differences in strain sensitivities to dips within pathogen species: Staphylococcus aureus, Staphylococcus chromogenes, and Streptococcus uberis. Species differences were also found where Mycoplasma bovis (97.9% log reduction) was the most sensitive to tested teat dips and Staphylococcus haemolyticus (71.4% log reduction) the most resistant. Experiment 2 results indicated that contact times of 30 and 45 s were equally effective in reducing recovered bacteria for dips D and E and were also significantly more effective than a 15-s contact time. No differences were seen in recovered bacteria between tested contact times after treatment with dip

Forming of High-strength Steels Using a Hot-melt Dry Lubricant

DEFF Research Database (Denmark)

Hörnström, Sven-Erik; Karlsson, Erik; Olsson, Mikael

2008-01-01

during forming resulting in seizure of the tool/steel sheet contact and extensive scratching of the steel sheet surface. As a result, a number of concepts have been developed in order to reduce the tendency to galling in metal forming, including the development of new dry lubricants, new forming tool...... steel grades and improved surface engineering treatments such as the deposition of low friction CVD and PVD coatings. In the present study the performance of a hot-melt dry lubricant in the forming of hot and cold rolled and hot-dip galvanized high strength steel has been evaluated and compared...... with a conventional rust protection oil using four different tests methods, i.e. a strip reduction test, a bending under tension test, a stretch-forming test and a pin-on disc test. In the tests, two different cold work tool steels, a conventional steel grade and a nitrogen alloyed PM steel grade were evaluated...

Deformation modeling and the strain transient dip test

International Nuclear Information System (INIS)

Jones, W.B.; Rohde, R.W.; Swearengen, J.C.

1980-01-01

Recent efforts in material deformation modeling reveal a trend toward unifying creep and plasticity with a single rate-dependent formulation. While such models can describe actual material deformation, most require a number of different experiments to generate model parameter information. Recently, however, a new model has been proposed in which most of the requisite constants may be found by examining creep transients brought about through abrupt changes in creep stress (strain transient dip test). The critical measurement in this test is the absence of a resolvable creep rate after a stress drop. As a consequence, the result is extraordinarily sensitive to strain resolution as well as machine mechanical response. This paper presents the design of a machine in which these spurious effects have been minimized and discusses the nature of the strain transient dip test using the example of aluminum. It is concluded that the strain transient dip test is not useful as the primary test for verifying any micromechanical model of deformation. Nevertheless, if a model can be developed which is verifiable by other experimentts, data from a dip test machine may be used to generate model parameters

Protocol for the microbial degradation of coumaphos from cattle dip

International Nuclear Information System (INIS)

Mulbry, W.; Karns, J.

1997-01-01

Insecticide wastes generated from livestock dipping operations are well suited for biodegradation processes since these wastes are concentrated, contained, and have no other significant toxic components. About 400,000 L of cattle dip wastes containing approximately 1500 mg/L of the organophosphate coumaphos are generated yearly along the Mexican border from a USDA program designed to control disease carrying cattle ticks. Use of unlined evaporation pits for the disposal of these wastes has resulted in highly contaminated soils underlying these sites. Previous work has shown that microbial consortia present in selected dip wastes can be induced to mineralize coumaphos. Our laboratory results show that these consortia are able to colonize plastic fibers in trickling biofilters and can be used in these filters to quickly metabolize coumaphos from dip wastes. A field scale biofilter capable of treating 15,000 litre batches of dip waste was used to reduce the coumaphos concentration in two successive 11,000 litre batch trials from 2000 mg/L to 10 mg/L in approximately 14 d. (author)

Effect of UV-C radiation and hot water on the calcium content and postharvest quality of apples

Energy Technology Data Exchange (ETDEWEB)

Hemmaty, S.; Moallemi, N.; Naseri, L.

2007-12-15

To increase the storage shelf life of 'Red Delicious' and 'Golden Delicious' apples they were treated with UV-C irradiation at doses of 0, 5 and 15 min irradiation at 1.435 x 10{sup -4} W/square cm{sup -} and with hot water containing 4% CaCl{sub 2} at four levels (control, dipping at 25 deg C for 10 min, dipping at 38 deg C for 5 min and dipping in 54 deg C for 1 min) in a factorial design with 4 replicates. The results showed that UV-C irradiation and dipping of fruit in hot water increased the storage life and improved fruit quality factors in 'Red Delicious' and 'Golden Delicious' apples at the end of cold storage. Both UV-C and hot water treatments decreased pH and total soluble solids/titratable acids ratio and increased fruit titratable acids and firmness. UV-C and hot water treatment increased fruit Ca content during storage. The results showed that UV-C and hot water treatment can retard fruit ripening and maintain fruit quality in cold storage. These treatments can also increase Ca concentration of fruit flesh and thus increase the nutritional value of the apples. (author) [Spanish] Con el fin de prolongar el periodo de vida útil durante la conservación frigorífica de manzanas ‘Red Delicious’ y ‘Golden Delicious’, éstas se trataron con radiación UV-C en tres dosis (0, 5 y 15 min de irradiación a 1,435 × 10{sup -4} W cm{sup -2}) y agua caliente con CaCl{sub 2} al 4% en cuatro niveles (control 0, inmersión a 25°C 10 min, 38°C 5 min ó 54°C 1 min), en un diseño factorial con 4 repeticiones por tratamiento. La irradiación con UV-C y la inmersión de los frutos en agua caliente permitió alargar el periodo de conservación y mejoró la calidad de manzanas ‘Red Delicious’ y ‘Golden Delicious’ tras el almacenamiento en frío. Ambos tratamientos aumentaron la acidez titulable y la firmeza de los frutos, también disminuyeron el pH y la relación sólidos solubles/acidez. El tratamiento con UV-C y agua caliente incrementó el contenido

UNDERSTANDING THE STRUCTURE OF THE HOT INTERSTELLAR MEDIUM IN NORMAL EARLY-TYPE GALAXIES.

Science.gov (United States)

Traynor, Liam; Kim, Dong-Woo; Chandra Galaxy Atlas

2018-01-01

The hot interstellar medium (ISM) of early-type galaxies (ETG's) provides crucial insight into the understanding of their formation and evolution. Mechanisms such as type Ia supernovae heating, AGN feedback, deepening potential depth through dark matter assembly and ramp-pressure stripping are known to affect the structure of the ISM. By using temperature maps and radial temperature profiles of the hot ISM from ~70 ETG's with archival Chandra data, it is possible to classify the galaxy's ISM into common structural types. This is extended by using 3D fitting of the radial temperature profile in order to provide models that further constrain the structural types. Five structural types are present, negative (temperature decreases with radii), positive (temperature increases with radii), hybrid-dip (temperature decreases at small radii and increases at large radii), hybrid-bump (inverse of hybrid-dip) and quasi-isothermal (temperature is constant at all radii). This work will be continued by 1) determining which mechanisms are present in which galaxies and 2) analysing the model parameters between galaxies within each structural type to determine whether each type can be described by a single set of model parameters, indicating that the same physical processes are responsible for creating that structural type.

Quantitative influence of minor and impurity elements on hot cracking susceptibility of extra high-purity type 310 stainless steel

International Nuclear Information System (INIS)

Saida, Kazuyoshi; Matsushita, Hideki; Nishimoto, Kazutoshi; Kiuchi, Kiyoshi; Nakayama, Junpei

2013-01-01

To evaluate the influence of minor and impurity elements such as C, Mn, P and S on the solidification and ductility-dip cracking susceptibilities of extra high-purity type 310 stainless steels, the transverse-Varestraint test was conducted by using several type 310 stainless steels with different amounts of C, Mn, P and S. Two types of hot cracks occurred in these steels by Varestraint test; solidification and ductility-dip cracks. The solidification cracking susceptibility was significantly reduced as the amounts of C, P and S decreased. The ductility-dip cracking susceptibility also reduced with a decrease in P and S contents. It adversely, however, increased as the C content of the steels was reduced. Mn didn't greatly affect the hot cracking susceptibility of the extra high-purity steels. The characteristic influence on solidification cracking was the ratio of P:S:C=1:1.3:0.56, while Mn negligibly ameliorated solidification cracking in the extra low S (and P) steels. The numerical analysis on the solidification brittle temperature range (BTR) revealed that the reduced solidification cracking susceptibility with decreasing the amounts of C, P and S in steel could be attributed to the reduced BTR due to the suppression of solidification segregation of minor and impurity elements in the finally solidified liquid film between dendrites. On the other hand, a molecular orbital analysis to estimate the binding strength of the grain boundary suggested that the increased ductility-dip cracking susceptibility in extra high-purity steels was caused by grain boundary embrittlement due to the refining of beneficial elements for grain boundary strengthening such as C. (author)

Effect of gamma irradiation with or without hot water dip and transportation from Thailand to Canada on nutritional qualities, ripening index and sensorial characteristics of Thai mangoes (Nahng Glahng Wahn variety)

International Nuclear Information System (INIS)

Lacroix, M.; Gagnon, M.; Pringsulaka, V.

1993-01-01

Mangoes of the Nahng Glahng Wahn variety from Thailand were irradiated at the Thai Irradiation Center (TIC) at 0.49 to 0.77 kGy. One batch was retained in Thailand while the other was shipped to the Canadian Irradiation Center (CIC) for investigation of the same variables during storage, to compare the effects of gamma radiation with hot water dip (HWI) or without (I) before and after transportation on the ripening, vitamin C and vitamin A content and sensory qualities of mangoes. The results indicate that the I and HWI treatments delayed the ripening of the mangoes. The irradiated groups appeared to have a slightly higher content of ascorbic acid on the first day after irradiation than their corresponding controls. The sensory evaluation indicates that the panelists mostly favoured the I and HWI irradiated groups for the overall appearance and texture of whole mangoes and pulp and in taste and palatability of the pulp alone. Transportation stress did not appear to have much effect on the ascorbic acid and dehydroascorbic acid levels and the sensorial tests. The mangoes stored and studied in Canada appeared to have a lower vitamin A content. (author)

Microscopic creep models and the interpretation of stress-dip tests during creep

International Nuclear Information System (INIS)

Poirier, J.P.

1976-09-01

A critical analysis is made of the principal divergent view points concerning stress-dip tests. The raw data are examined and interpreted in the light of various creep models. The following problems are discussed: is the reverse strain anelastic or plastic; is the zero creep rate periodic due to recovery or is it spurious; can the existence or inexistence of an internal stress be deduced from stress-dip tests; can stress-dip tests allow to determine whether glide is jerky or viscous; can the internal stress be measured by stress-dip tests

Multiple-Satellite Observation of Magnetic Dip Event During the Substorm on 10 October 2013

Science.gov (United States)

He, Zhaoguo; Chen, Lunjin; Zhu, Hui; Xia, Zhiyang; Reeves, G. D.; Xiong, Ying; Xie, Lun; Cao, Yong

2017-09-01

We present a multiple-satellite observation of the magnetic dip event during the substorm on 10 October 2013. The observation illustrates the temporal and spatial evolution of the magnetic dip and gives a compelling evidence that ring current ions induce the magnetic dip by enhanced plasma beta. The dip moves with the energetic ions in a comparable drift velocity and affects the dynamics of relativistic electrons in the radiation belt. In addition, the magnetic dip provides a favorable condition for the electromagnetic ion cyclotron (EMIC) wave generation based on the linear theory analysis. The calculated proton diffusion coefficients show that the observed EMIC wave can lead to the pitch angle scattering losses of the ring current ions, which in turn partially relax the magnetic dip in the observations. This study enriches our understanding of magnetic dip evolution and demonstrates the important role of the magnetic dip for the coupling of radiation belt and ring current.

A set of 14 DIP-SNP markers to detect unbalanced DNA mixtures.

Science.gov (United States)

Liu, Zhizhen; Liu, Jinding; Wang, Jiaqi; Chen, Deqing; Liu, Zidong; Shi, Jie; Li, Zeqin; Li, Wenyan; Zhang, Gengqian; Du, Bing

2018-03-04

Unbalanced DNA mixture is still a difficult problem for forensic practice. DIP-STRs are useful markers for detection of minor DNA but they are not widespread in the human genome and having long amplicons. In this study, we proposed a novel type of genetic marker, termed DIP-SNP. DIP-SNP refers to the combination of INDEL and SNP in less than 300bp length of human genome. The multiplex PCR and SNaPshot assay were established for 14 DIP-SNP markers in a Chinese Han population from Shanxi, China. This novel compound marker allows detection of the minor DNA contributor with sensitivity from 1:50 to 1:1000 in a DNA mixture of any gender with 1 ng-10 ng DNA template. Most of the DIP-SNP markers had a relatively high probability of informative alleles with an average I value of 0.33. In all, we proposed DIP-SNP as a novel kind of genetic marker for detection of minor contributor from unbalanced DNA mixture and established the detection method by associating the multiplex PCR and SNaPshot assay. DIP-SNP polymorphisms are promising markers for forensic or clinical mixture examination because they are shorter, widespread and higher sensitive. Copyright © 2018 Elsevier Inc. All rights reserved.

29 CFR 1910.126 - Additional requirements for special dipping and coating operations.

Science.gov (United States)

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false Additional requirements for special dipping and coating... Dipping and Coating Operations § 1910.126 Additional requirements for special dipping and coating... requirements apply to flow coating? (1) You must use a direct low-pressure pumping system or a 10-gallon (38 L...

DiPS: A Unifying Approach for developing System Software

OpenAIRE

Michiels, Sam; Matthijs, Frank; Walravens, Dirk; Verbaeten, Pierre

2002-01-01

In this paper we unify three essential features for flexible system software: a component oriented approach, self-adaptation and separation of concerns.We propose DiPS (Distrinet Protocol Stack), a component framework, which offers components, an anonymous interaction model and connectors to handle non-functional aspects such as concurrency. DiPS has effectively been used in industrial protocol stacks and device drivers.

Influence of Experimental Parameters Using the Dip-Coating Method on the Barrier Performance of Hybrid Sol-Gel Coatings in Strong Alkaline Environments

Directory of Open Access Journals (Sweden)

Rita B. Figueira

2015-04-01

Full Text Available Previous studies have shown that the barrier effect and the performance of organic-inorganic hybrid (OIH sol-gel coatings are highly dependent on the coating deposition method as well as on the processing conditions. However, studies on how the coating deposition method influences the barrier properties in alkaline environments are scarce. The aim of this experimental research was to study the influence of experimental parameters using the dip-coating method on the barrier performance of an OIH sol-gel coating in contact with simulated concrete pore solutions (SCPS. The influence of residence time (Rt, a curing step between each dip step and the number of layers of sol-gel OIH films deposited on hot-dip galvanized steel to prevent corrosion in highly alkaline environments was studied. The barrier performance of these OIH sol-gel coatings, named U(400, was assessed in the first instants of contact with SCPS, using electrochemical impedance spectroscopy and potentiodynamic methods. The durability and stability of the OIH coatings in SCPS was monitored during eight days by macrocell current density. The morphological characterization of the surface was performed by Scanning Electronic Microscopy before and after exposure to SCPS. Glow Discharge Optical Emission Spectroscopy was used to investigate the thickness of the U(400 sol-gel coatings as a function of the number of layers deposited with and without Rt in the coatings thickness.

Trapping dynamics of diindenoperylene (DIP) in self-assembled monolayers using molecular simulation

KAUST Repository

Kaushik, Ananth P.

2011-07-01

All-atom Molecular Dynamics simulation methods employing a well-tested intermolecular potential model, MM3 (Molecular Mechanics 3), demonstrate the propensity for diindenoperylene (DIP) molecules to insert between molecules of a self-assembled monolayer (SAM) during a deposition process intended to grow a thin film of this organic semiconductor molecule onto the surface of self-assembled monolayers. The tendency to insert between SAM molecules is fairly prevalent at normal growth temperatures and conditions, but is most strongly dependent on the density and the nature of the SAM. We posit the existence of an optimal density to favor surface adsorption over insertion for this system. DIP is less likely to insert in fluorinated SAMs, like FOTS (fluorooctatrichlorosilane), than its unfluorinated analog, OTS (octatrichlorosilane). It is also less likely to insert between shorter SAMs (e.g., less insertion in OTS than ODTS (octadecyltrichlorosilane)). Very short length, surface-coating molecules, like HDMS (hexamethyldisilazane), are more likely to scatter energetic incoming DIP molecules with little insertion on first impact (depending on the incident energy of the DIP molecule). Grazing angles of incidence of the depositing molecules generally favor surface adsorption, at least in the limit of low coverage, but are shown to be dependent on the nature of the SAM. The validity of these predictions is confirmed by comparison of the predicted sticking coefficients of DIP at a variety of incident energies on OTS, ODTS, and FOTS SAMs with results obtained experimentally by Desai et al. (2010) [23]. The simulation predictions of the tendency of DIP to insert can be explained, in large part, in terms of binding energies between SAM and DIP molecules. However, we note that entropic and stochastic events play a role in the deposition outcomes. Preliminary studies of multiple deposition events, emulating growth, show an unexpected diffusion of DIP molecules inserted within the

Dynamic nanomechanical properties of novel Si-rich intermetallic coatings growth on a medical 316 LVM steel by hot dipping in a hypereutectic Al-25Si alloy.

Science.gov (United States)

Frutos, E; González-Carrasco, J L

2015-06-01

This aim of this study is to determine the elastoplastic properties of Ni-free Al3FeSi2 intermetallic coatings grown on medical stainless steel under different experimental conditions. Elastoplastic properties are defined by the plasticity index (PI), which correlates the hardness and the Young's modulus. Special emphasis is devoted to correlate the PI with the wear resistance under sliding contact, determined by scratch testing, and fracture toughness, determined by using a novel method based on successive impacts with small loads. With regard to the substrate, the developed coatings are harder and exhibit a lower Young's reduced modulus, irrespective of the experimental conditions. It has been shown that preheating of the samples prior to hot dipping and immersion influences the type and volume fraction of precipitates, which in turn also affect the nanomechanical properties. The higher the preheating temperature is, the greater the Young's reduced modulus is. For a given preheating condition, an increase of the immersion time yields a decrease in hardness. Although apparent friction coefficients of coated specimens are smaller than those obtained on AISI 316 LVM, they increase when using preheating or higher immersion times during processing, which correlates with the PI. The presence of precipitates produces an increase in fracture toughness, with values greater than those presented by samples processed on melted AlSi alloys with lower Si content (12 wt%). Therefore, these intermetallic coatings could be considered "hard but tough", suitable to enhance the wear resistance, especially when using short periods of immersion. Copyright © 2015 Elsevier Ltd. All rights reserved.

Image mispositioning due to dipping TI media : a physical seismic modelling study

Energy Technology Data Exchange (ETDEWEB)

Isaac, J.H.; Lawton, D.C.

1998-09-01

Physical modelling experiments were performed to study mispositioning of targets imaged beneath a dipping anisotropic overburden. The significance of the study is that many hydrocarbon resource exploration and development plays in different tectonic settings involve dipping clastic sequences which lie above the reservoir or target zone. In many areas in the Alberta foothills, dipping panels of relatively undeformed Wapiabi shales are found in abundance, overlying deep carbonate reservoirs. These experiments demonstrated the magnitude of the image mispositioning incurred by the use of an inappropriate isotropic processing code when velocity anisotropy was present in the overburden. It was shown that the lateral shift of an imaged target beneath a 1500 m thick, 45 degree dipping anisotropic overburden is significant. Zero-offset data showed a shift in the imaged location of 320 m in the updip direction of the dipping beds, while the shift on stacked time and depth migrated multichannel data was 300 m. 2 refs., 2 figs.

Dip and anisotropy effects on flow using a vertically skewed model grid.

Science.gov (United States)

Hoaglund, John R; Pollard, David

2003-01-01

Darcy flow equations relating vertical and bedding-parallel flow to vertical and bedding-parallel gradient components are derived for a skewed Cartesian grid in a vertical plane, correcting for structural dip given the principal hydraulic conductivities in bedding-parallel and bedding-orthogonal directions. Incorrect-minus-correct flow error results are presented for ranges of structural dip (0 strike and dip, and a solver that can handle off-diagonal hydraulic conductivity terms.

Rangeland degradation in semi-arid Swaziland: effects of dip-tanks ...

African Journals Online (AJOL)

This study investigated dip-tank use effects on herbaceous vegetation and soil, and relationships between environmental and species variables. Eight dip-tanks, three each in sandy (DPBS) and loamy (DYRL) soils, and two in stony (ROSG) soils were used. Data were collected at 50, 100, 150, 300, 500, 700 and 900 m from ...

Experimental Modeling of Dynamic Shallow Dip-Slip Faulting

Science.gov (United States)

Uenishi, K.

2010-12-01

In our earlier study (AGU 2005, SSJ 2005, JPGU 2006), using a finite difference technique, we have conducted some numerical simulations related to the source dynamics of shallow dip-slip earthquakes, and suggested the possibility of the existence of corner waves, i.e., shear waves that carry concentrated kinematic energy and generate extremely strong particle motions on the hanging wall of a nonvertical fault. In the numerical models, a dip-slip fault is located in a two-dimensional, monolithic linear elastic half space, and the fault plane dips either vertically or 45 degrees. We have investigated the seismic wave field radiated by crack-like rupture of this straight fault. If the fault rupture, initiated at depth, arrests just below or reaches the free surface, four Rayleigh-type pulses are generated: two propagating along the free surface into the opposite directions to the far field, the other two moving back along the ruptured fault surface (interface) downwards into depth. These downward interface pulses may largely control the stopping phase of the dynamic rupture, and in the case the fault plane is inclined, on the hanging wall the interface pulse and the outward-moving Rayleigh surface pulse interact with each other and the corner wave is induced. On the footwall, the ground motion is dominated simply by the weaker Rayleigh pulse propagating along the free surface because of much smaller interaction between this Rayleigh and the interface pulse. The generation of the downward interface pulses and corner wave may play a crucial role in understanding the effects of the geometrical asymmetry on the strong motion induced by shallow dip-slip faulting, but it has not been well recognized so far, partly because those waves are not expected for a fault that is located and ruptures only at depth. However, the seismological recordings of the 1999 Chi-Chi, Taiwan, the 2004 Niigata-ken Chuetsu, Japan, earthquakes as well as a more recent one in Iwate-Miyagi Inland

Dip Phenomenon in High-Curved Turbulent Flows and Application of Entropy Theory

Directory of Open Access Journals (Sweden)

Donatella Termini

2018-03-01

Full Text Available The estimation of velocity profile in turbulent open channels is a difficult task due to the significant effects of the secondary flow. The present paper investigates the mechanism of the velocity-dip phenomenon, whereby the location of the maximum velocity appears to be below the free surface. Previous studies conducted in straight channels relate the mechanism of the velocity-dip phenomenon to secondary flow induced by anisotropy of turbulence. This work focuses on high-curved channels where the secondary motion, which is also induced by the channel’s curvature, evolves along the bend. The width-to-depth ratio, B/h, is one of the most important parameters that are affecting the secondary motion entity. In particular, the present study aims to investigate the evolution of the velocity-dip along the bend for two values of the width-to-depth ratio and the applicability of the entropic model for the dip-phenomenon estimation. The results show that the velocity-dip is more accentuated for low values of the width-to-depth ratio, where the secondary motion plays a fundamental role in the distribution of the downstream flow velocity, although the velocity-dip is also present when the aspect ratio is higher than 10. Furthermore, the velocity profiles that were estimated by applying the entropic model are in good agreement with the measured ones, especially for B/h < 10.

Dipping Strawberry Plants in Fungicides before Planting to Control Anthracnose

Directory of Open Access Journals (Sweden)

Myeong Hyeon Nam

2014-03-01

Full Text Available Anthracnose crown rot (ACR, caused by Colletotrichum fructicola, is a serious disease of strawberry in Korea. The primary inoculums of ACR were symptomless strawberry plants, plant debris, and other host plants. To effectively control anthracnose in symptomless transplanted strawberries, it is necessary to use diseasefree plants, detect the disease early, and apply a fungicide. Therefore, in 2010 and 2011, we evaluated the efficacy of pre-plant fungicide dips by using strawberry transplants infected by C. fructicola for the control of anthracnose. Dipping plants in prochloraz-Mn for 10 min before planting was most effective for controlling anthracnose in symptomless strawberry plants and resulted in more than 76% control efficacy. Azoxystrobin showed a control efficacy of over 40%, but plants treated with pyraclostrobin, mancozeb and iminoctadine tris showed high disease severity. The control efficacy of the dip treatment with prochloraz-Mn did not differ with temperature and time. Treatment with prochloraz-Mn for more than an hour caused growth suppression in strawberry plants. Therefore, the development of anthracnose can be effectively reduced by dipping strawberry plants for 10 min in prochloraz-Mn before planting.

Assessment of voltage dips based on field measurements in MV networks

NARCIS (Netherlands)

Weldemariam, L.E.; Papathanasiou, F.; Cuk, V.; Cobben, J.F.G.; Kling, W.L.

Voltage dip is considered as the PQ problem related to the highest financial losses for the customers. It occurs unpredictably mainly due to short-circuit faults in the networks. Network operators and customers want to know more about the occurrence and the potential impact of voltage dips. PQ

EFFECT OF CHEMICAL MODIFICATION AND HOT-PRESS DRYING ON POPLAR WOOD

Directory of Open Access Journals (Sweden)

Guo-Feng Wu

2010-11-01

Full Text Available Urea-formaldehyde prepolymer and hot-press drying were used to improve the properties of poplar wood. The wood was impregnated with the prepolymer using a pulse-dipping machine. The impregnated timbers were compressed and dried by a multilayer hot-press drying kiln. The drying rate was more rapid during the chemical modification and hot-press drying than conventional kiln-drying. In addition, the properties of timber were also enhanced obviously. When the compression rate was 28.6%, the basic density, oven dry density and air-dried density of modified wood improved 22%, 71%, and 70%, respectively. The bending strength and compressive strength parallel to grain increased 60% and 40%. The water uptake of treated wood was significantly decreased compared with the untreated wood. The FTIR analysis successfully showed that the intensity of hydroxyl and carbonyl absorption peaks decreased significantly, which was attributed to a reaction of the NHCH2OH of urea-formaldehyde prepolymer with the wood carboxyl (C=O and hydroxyl (-OH groups. The XRD results indicated that the degree of crystallinity increased from 35.09% to 36.91%. The morphologic models of chemical within wood were discovered by SEM.

The potential of postharvest silicon dips to regulate phenolics in ...

African Journals Online (AJOL)

This study investigated the ability of silicon dips to enhance the phenolic content in order to reduce the incidence of chilling injury in lemon fruit. Fruits were obtained from two farms and dipped in 0, 50, 150 and 250 mg L-1 solutions of K2SiO3 for 30 min and afterward, fruit were air dried and waxed. Thereafter, fruits were ...

Trapping dynamics of diindenoperylene (DIP) in self-assembled monolayers using molecular simulation

KAUST Repository

Kaushik, Ananth P.; Clancy, Paulette

2011-01-01

(hexamethyldisilazane), are more likely to scatter energetic incoming DIP molecules with little insertion on first impact (depending on the incident energy of the DIP molecule). Grazing angles of incidence of the depositing molecules generally favor surface adsorption

DIP1 modulates stem cell homeostasis in Drosophila through regulation of sisR-1.

Science.gov (United States)

Wong, Jing Ting; Akhbar, Farzanah; Ng, Amanda Yunn Ee; Tay, Mandy Li-Ian; Loi, Gladys Jing En; Pek, Jun Wei

2017-10-02

Stable intronic sequence RNAs (sisRNAs) are by-products of splicing and regulate gene expression. How sisRNAs are regulated is unclear. Here we report that a double-stranded RNA binding protein, Disco-interacting protein 1 (DIP1) regulates sisRNAs in Drosophila. DIP1 negatively regulates the abundance of sisR-1 and INE-1 sisRNAs. Fine-tuning of sisR-1 by DIP1 is important to maintain female germline stem cell homeostasis by modulating germline stem cell differentiation and niche adhesion. Drosophila DIP1 localizes to a nuclear body (satellite body) and associates with the fourth chromosome, which contains a very high density of INE-1 transposable element sequences that are processed into sisRNAs. DIP1 presumably acts outside the satellite bodies to regulate sisR-1, which is not on the fourth chromosome. Thus, our study identifies DIP1 as a sisRNA regulatory protein that controls germline stem cell self-renewal in Drosophila.Stable intronic sequence RNAs (sisRNAs) are by-products of splicing from introns with roles in embryonic development in Drosophila. Here, the authors show that the RNA binding protein DIP1 regulates sisRNAs in Drosophila, which is necessary for germline stem cell homeostasis.

Current trend in latex dipped products manufacturing

International Nuclear Information System (INIS)

Wong, W.S.C.

1996-01-01

The paper present the activities in dipped products manufacturing in Malaysia; the activities carried out by MARGMA - Malaysian Rubber Glove manufacturer; other issues discussed such as labour, pricing environmental issue, product certification in this activity

Structural analysis of CdS thin films obtained by multiple dips of oscillating chemical bath

Energy Technology Data Exchange (ETDEWEB)

Gutierrez Lazos, C.D. [Seccion de Electronica del Estado Solido, Centro de Investigacion y de Estudios Avanzados, Av. Instituto Politecnico Nacional 2508, Col. San Pedro Zacatenco, 07360 Mexico, D.F. (Mexico); Rosendo, E., E-mail: erosendo@siu.buap.m [Centro de Investigacion en Dispositivos Semiconductores, Universidad Autonoma de Puebla, 14 Sur y San Claudio, Col. San Manuel, C.P. 72570, Puebla (Mexico); Ortega, M. [Seccion de Electronica del Estado Solido, Centro de Investigacion y de Estudios Avanzados, Av. Instituto Politecnico Nacional 2508, Col. San Pedro Zacatenco, 07360 Mexico, D.F. (Mexico); Oliva, A.I. [Departamento de Fisica Aplicada, Centro de Investigacion y de Estudios Avanzados, Unidad Merida, A.P. 73 Cordemex, 97310 Merida, Yucatan (Mexico); Tapia, O.; Diaz, T.; Juarez, H.; Garcia, G. [Centro de Investigacion en Dispositivos Semiconductores, Universidad Autonoma de Puebla, 14 Sur y San Claudio, Col. San Manuel, C.P. 72570, Puebla (Mexico); Rubin, M. [Facultad de Ciencias de la Computacion, 14 Sur y San Claudio, Col. San Manuel, C.P. 72570, Puebla (Mexico)

2009-11-25

Highly oriented CdS thin films with thicknesses greater than 1 mum were deposited by multiple dips, using oscillating chemical bath deposition (OCBD) at the bath temperature of 75 deg. C, and deposition time ranging from 15 to 75 min for a single dip. Samples with different thickness were prepared by repeating the deposition process for two and three times. The films deposited by a single dip have the alpha-greenockite structure showing the (0 0 2) as preferred orientation, as indicated by the X-ray diffraction measurements. This notable characteristic is preserved in the samples obtained from two or three dips. The crystallite size for the samples deposited by a single dip depends on the deposition time, because it varied from 23 to 37 nm as the deposition time increased. Nevertheless for samples deposited by two and three dips, the grain size shows no noticeable change, being about 22 nm.

Particle and power balances of hot-filament discharge plasmas in a multi-dipole device in the presence of a positively biased electrode

International Nuclear Information System (INIS)

Cho, M.H.; Hershkowitz, N.; Intrator, T.

1989-01-01

The plasma potential is typically assumed to float above an anode potential by a few times of an electron temperature (T /e). The difference between the plasma potential and the anode potential can be estimated by considering the particle production and loss. However, it has been reported experimentally that the plasma potential of a steady state plasma can be more negative than the anode potential with a potential dip (-- T /e) in front of the anode. This paper describes particle and power balances to estimate the bulk plasma potential of a hot-filament discharge plasma produced in a multi-dipole plasma device. The bulk plasma potential dependence on positive DC bias applied to an anode is analyzed, and the predicted characteristics of the plasma potential dependence are compared to the experiment. A steady state potential dip in front of an anode is experimentally observed using emissive probes with the zero emission inflection point method, and the conditions for the potential dip formation are derived

Synthesis of active absorber layer by dip-coating method for perovskite solar cell

Science.gov (United States)

Singh, Rahul; Noor, I. M.; Singh, Pramod K.; Bhattacharya, B.; Arof, A. K.

2018-04-01

In this paper, we develop the hybrid perovskite-based n-i-p solar cell using a simple, fast and low-cost dip-coating method. Hot solution and the pre-annealed substrate are used for coating the perovskite thin film by this method this is further used for studying its structural and electrical properties. UV-vis spectroscopy is carried out for calculating the band gap of the hybrid perovskite layer which is ∼1.6 eV. X-ray spectroscopy confirms that the formation of hybrid perovskite layer. The profilometer is used to study the surface roughness and also for measuring the thickness of the perovskite layer with varying substrate temperature. The optimized sample was further used for cross-sectional SEM image to verify the thickness measured from the profiler. The electrical parameter of JV characteristic with varying temperature is tabulated in the table. Whereas, the perovskite sensitized solar cell exhibits highest short circuit current density, Jsc of 11 mA cm-2, open circuit voltage, Voc of 0.87 V, fill factor of 0.55 and efficiency, η of >5%.

Monitoring of Dips in the MV Network for Regulation- A Case Study

NARCIS (Netherlands)

Weldemariam, L.E.; Cuk, V.; Cobben, J.F.G.; Kling, W.L.

2014-01-01

Abstract— Voltage dips constitute to a noticeable part of power quality (PQ) problems but causing major financial losses to industrial and commercial customers. This work involves comparative studies to choose the most appropriate location of monitoring dips for regulation. In this paper, a Dutch MV

Development of flow-through and dip-stick immunoassays for screening of sulfonamide residues.

Science.gov (United States)

Zhang, Hongyan; Zhang, Yan; Wang, Shuo

2008-08-20

Two formats of membrane-based competitive enzyme immunoassays (flow-through and dip-stick) have been developed for the screening of sulfonamide residues in pig muscle and milk. Membrane was coated with anti-sulfonamide antibody and a sulfonamide hapten D2-horseradish peroxidase (HRP) conjugant was used as the labeled antigen for competitive assay of sulfonamides. Visual detection limits of the flow-through or dip-stick assay were 1-5 microg L(-1) or 1-10 microg L(-1) in buffer for seven sulfonamides, respectively. Assay validation was performed using samples spiked with single sulfonamide, spiked samples were tested using the developed strip assays and results were compared with those obtained by a validated high-performance liquid chromatograph (HPLC) method. Results showed that the two strip assays were correlated well with HPLC, respectively. With assay times of 5 min (flow-through) and 15 min (dip-stick), these rapid tests could offer simple, rapid and cost-effective on-site screening tools to detect sulfonamides in pig muscle (flow-through or dip-stick) or milk (only dip-stick).

Efficiency dip observed with InGaN-based multiple quantum well solar cells

KAUST Repository

Lai, Kunyu; Lin, G. J.; Wu, Yuhrenn; Tsai, Menglun; He, Jr-Hau

2014-01-01

The dip of external quantum efficiency (EQE) is observed on In0.15Ga0.85N/GaN multiple quantum well (MQW) solar cells upon the increase of incident optical power density. With indium composition increased to 25%, the EQE dip becomes much less noticeable. The composition dependence of EQE dip is ascribed to the competition between radiative recombination and photocurrent generation in the active region, which are dictated by quantum-confined Stark effect (QCSE) and composition fluctuation in the MQWs.

Dip-Coating Process Engineering and Performance Optimization for Three-State Electrochromic Devices

Science.gov (United States)

Wu, Lu; Yang, Dejiang; Fei, Lixun; Huang, Yue; Wu, Fang; Sun, Yiling; Shi, Jiayuan; Xiang, Yong

2017-06-01

Titanium dioxide (TiO2) nanoparticles were modified onto fluorine-doped tin oxide (FTO) via dip-coating technique with different nanoparticle sizes, lifting speeds, precursor concentrations, and dipping numbers. Electrodeposition-based electrochromic device with reversible three-state optical transformation (transparent, mirror, and black) was fabricated subsequently by sandwiching a suitable amount of gel electrolyte between modified FTO electrode and flat FTO electrode. Correlation between dip-coating process engineering, morphological features of TiO2 thin films, i.e., thickness and roughness, as well as performance of electrochromic devices, i.e., optical contrast, switching time, and cycling stability, were investigated. The modified device exhibits high optical contrast of 57%, the short coloration/bleaching switching time of 6 and 20 s, and excellent cycling stability after 1500 cycles of only 27% decrement rate by adjusting dip-coating processes engineering. The results in this study will provide valuable guidance for rational design of the electrochromic device with satisfactory performance.

Persistence of lindane in model cattle dips in sub-tropical climate of Delhi, India

International Nuclear Information System (INIS)

Singh, D.K.; Menon, P.; Agarwal, H.C.

1997-01-01

Persistence of lindane in model cattle dips under field conditions in the sub-tropical climate of Delhi was studied. In one set of experiments two model dips were utilized and filled with 200 L of water and treated with 2.37 MBq of 14 C-labelled and 4 g unlabelled lindane each. The radioactivity in water samples at zero time was estimated and considered to be 100 % (744 dpm/mL) which declined to 17.5 % (132 dpm/mL) 180 d after the treatment in Dip 1 (control dip). In the second dip 50 g of cowdung and soil were added 28 d after treatment and subsequently every time before sampling. The results in both the dips were similar indicating no effect of soil and cowdung on the persistence of lindane in the dips. The half life of lindane in water was 101 days. Lindane was extracted from water by hexane in the presence of methanol. The efficiency of this procedure was 99+ %. The main metabolises of lindane in water, identified by HPLC, were 1, 2, 4- trichlorobenzene, 1,3,5-trichlorobenzene and an unknown compound. In another experiment, 50 L of water was added to one dip which was treated with 2.90 MBq of 14 C-labelled and 1 g unlabelled lindane in 25 ml acetone. The cattle dip was recharged at monthly intervals with about 10 % of the initially applied lindane (290 kBq of 14 C labelled and 100 mg unlabelled lindane in 25 mL acetone). Soil and cow dung were added as in the first experiment. The concentration of lindane declined rapidly to 11.69 % (1.9 μg/mL, 425 dpm/mL) after the third recharge. The main metabolite was 1,2,4- trichlorobenzene which accounted for about 21 % after first and second recharge. The effect of pH ranging from 5 to 9 was also investigated. The dissipation appeared to be faster at pH 8 and comparatively slower at pH 6. (author)

Novel dip-pen nanolithography strategies for nanopatterning

NARCIS (Netherlands)

Wu, C.C.

2010-01-01

Dip-pen nanolithography (DPN) is an atomic force microscopy (AFM)-based lithography technique offering the possibility of fabricating patterns with feature sizes ranging from micrometers to tens of nanometers, utilizing either top-down or bottom-up strategies. Although during its early development

Continentward-Dipping Normal Faults, Boudinage and Ductile Shear at Rifted Passive Margins

Science.gov (United States)

Clerc, C. N.; Ringenbach, J. C.; Jolivet, L.; Ballard, J. F.

2017-12-01

Deep structures resulting from the rifting of the continental crust are now well imaged by seismic profiles. We present a series of recent industrial profiles that allow the identification of various rift-related geological processes such as crustal boudinage, ductile shear of the base of the crust and low-angle detachment faulting. Along both magma-rich and magma-poor rifted margins, we observe clear indications of ductile deformation of the deep continental crust. Large-scale shallow dipping shear zones are identified with a top-to-the-continent sense of shear. This sense of shear is consistent with the activity of the Continentward-Dipping Normal Faults (CDNF) that accommodate the extension in the upper crust. This pattern is responsible for an oceanward migration of the deformation and of the associated syn-tectonic deposits (sediments and/or volcanics). We discuss the origin of the Continentward-Dipping Normal Faults (CDNF) and investigate their implications and the effect of sediment thermal blanketing on crustal rheology. In some cases, low-angle shear zones define an anastomosed pattern that delineates boudin-like structures that seem to control the position and dip of upper crustal normal faults. We present some of the most striking examples from several locations (Uruguay, West Africa, South China Sea…), and discuss their rifting histories that differ from the classical models of oceanward-dipping normal faults.

Optical properties of titanium di-oxide thin films prepared by dip coating method

Science.gov (United States)

Biswas, Sayari; Rahman, Kazi Hasibur; Kar, Asit Kumar

2018-05-01

Titanium dioxide (TiO2) thin films were prepared by sol-gel dip coating method on ITO coated glass substrate. The sol was synthesized by hydrothermal method at 90°C. The sol was then used to make TiO2 films by dip coating. After dip coating the rest of the sol was dried at 100°C to make TiO2 powder. Thin films were made by varying the number of dipping cycles and were annealed at 500°C. XRD study was carried out for powder samples that confirms the formation of anatase phase. Transmission spectra of thin films show sharp rise in the violet-ultraviolet transition region and a maximum transmittance of ˜60%. Band gap of the prepared films varies from 3.15 eV to 3.22 eV.

Numerical prediction of a dip effect in the critical current density

International Nuclear Information System (INIS)

Al Khawaja, U.; Benkraouda, M.; Obaidat, I.M.

2007-01-01

We have conducted extensive series of molecular dynamic simulations on the properties of the critical current density in systems with periodic square arrays of pinning sites. The density of the pinning sites was kept fixed while the density of vortices, pinning strength, and temperature were varied several times. At zero temperature, we have observed a substantial dip in the critical current density that occurs only at a fixed value of the vortex density and for specific values of pinning strength. We have found that the occurrence of the dip depends mainly on the initial positions of the vortices with respect to the positions of the pinning sites. At the dip, we have found that the interstitial vortices form moving channels leading to the observed drop in the critical current density

Analysis of Mechanical Stresses Due to Voltage Dips in Fixed-Speed Wind Turbines

DEFF Research Database (Denmark)

Veluri, Badrinath; Santos-Martin, David; Jensen, Henrik Myhre

2011-01-01

stresses transients that may have a detrimental effect on the fatigue life of drivetrain system due to voltage dips. A rainflow cycle counting method for the stress history during the voltage dip event, analyses mean and amplitudes of the counted cycles, their occurrence moment and time of duration.......Voltage dips due to electrical grid faults generate transients of the generator electromagnetic torque which result in significant high stresses and noticeable vibrations for the wind turbine mechanical system. These events may also have a detrimental effect on the fatigue life of important...

Anti-double dipping rules for federal tax incentives

Energy Technology Data Exchange (ETDEWEB)

Ing, E.T.C. [Law Office of Edwin T.C. Ing, Washington, DC (United States)

1997-12-31

Political as well as technological changes are now reshaping the electric utility industry. While accommodating these changes, state legislative and regulatory agencies have the opportunity to promote public policies. In this regard, various state entities are evaluating appropriate incentives for renewable energy development so as to introduce greater competition in electric generation. For example, the California legislature is considering a supplemental production payment and the State of Iowa has instituted a low-interest loan program for wind and other alternative energy generation. By complementing the existing federal tax incentives, state incentives can spur the wind industry`s growth. If structured in the wrong way, however, state assistance programs will undercut the value of the federal tax incentives. The federal anti-double dipping rules apply to certain state programs. If a developer utilizes the wrong type of state assistance for a wind project, the anti-double dipping rules will reduce the federal tax incentives and this in turn will decrease the project`s profitability. Rather than suffer these results, very few if any developer will use the state program. Despite the time and effort a state may expend to enact a program for alternative energy development, the state assistance will be ineffectual. This paper reviews the counterproductive results which state assistance can have on a wind project because of the federal anti-double dipping rules.

Investigation of Dip-Coating Parameters Effect on The Performance of Alumina-Polydimethylsiloxane Nanofiltration Membranes for Desalination

OpenAIRE

Mohammad Hadi Yousefi; Mohamad Mehdi Zerafat; Majid Shokri Doodeji; Samad Sabbaghi

2017-01-01

The objective of this work is to investigate the effect of dip-coating parameters on the performance of Alumina-PDMS hybrid nanofiltration membranes for water desalination. Ceramic supports used in this work were prepared with a 340 nm average pore size and 34% total porosity. The aim is to determine optimum conditions of dipping time, PDMS concentration, and withdrawal speed in order to achieve high rejection and flux values. Dip-coating parameters were considered as dipping time (60 - 120 s...

9 CFR 72.13 - Permitted dips and procedures.

Science.gov (United States)

2010-01-01

... proprietary brands of permitted dips—as well the use of compressed air, vat management techniques, and other... maintained and that under actual field conditions the dipping of cattle with a solution of definite strength...

Spin coated versus dip coated electrochromic tungsten oxide films: Structure, morphology, optical and electrochemical properties

International Nuclear Information System (INIS)

Deepa, M.; Saxena, T.K.; Singh, D.P.; Sood, K.N.; Agnihotry, S.A.

2006-01-01

A sol-gel derived acetylated peroxotungstic acid sol encompassing 4 wt.% of oxalic acid dihydrate (OAD) has been employed for the deposition of tungsten oxide (WO 3 ) films by spin coating and dip coating techniques, in view of smart window applications. The morphological and structural evolution of the as-deposited spin and dip coated films as a function of annealing temperature (250 and 500 o C) has been examined and compared by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) and X-ray diffraction (XRD). A conspicuous feature of the dip coated film (annealed at 250 o C) is that its electrochromic and electrochemical properties ameliorate with cycling without degradation in contrast to the spin coated film for which these properties deteriorate under repetitive cycling. A comparative study of spin and dip coated nanostructured thin films (annealed at 250 o C) revealed a superior performance for the cycled dip coated film in terms of higher transmission modulation and coloration efficiency in solar and photopic regions, faster switching speed, higher electrochemical activity as well as charge storage capacity. While the dip coated film could endure 2500 color-bleach cycles, the spin coated film could sustain only a 1000 cycles. The better cycling stability of the dip coated film which is a repercussion of a balance between optimal water content, porosity and grain size hints at its potential for electrochromic window applications

Discovery of Periodic Dips in the Brightest Hard X-Ray Source of M31 with EXTraS

Science.gov (United States)

Marelli, Martino; Tiengo, Andrea; De Luca, Andrea; Salvetti, David; Saronni, Luca; Sidoli, Lara; Paizis, Adamantia; Salvaterra, Ruben; Belfiore, Andrea; Israel, Gianluca; Haberl, Frank; D’Agostino, Daniele

2017-12-01

We performed a search for eclipsing and dipping sources in the archive of the EXTraS project—a systematic characterization of the temporal behavior of XMM-Newton point sources. We discovered dips in the X-ray light curve of 3XMM J004232.1+411314, which has been recently associated with the hard X-ray source dominating the emission of M31. A systematic analysis of XMM-Newton observations revealed 13 dips in 40 observations (total exposure time of ∼0.8 Ms). Among them, four observations show two dips, separated by ∼4.01 hr. Dip depths and durations are variable. The dips occur only during low-luminosity states ({L}0.2{--12}< 1× {10}38 erg s‑1), while the source reaches {L}0.2{--12}∼ 2.8× {10}38 erg s‑1. We propose that this system is a new dipping low-mass X-ray binary in M31 seen at high inclination (60°–80°) the observed dipping periodicity is the orbital period of the system. A blue HST source within the Chandra error circle is the most likely optical counterpart of the accretion disk. The high luminosity of the system makes it the most luminous (not ULX) dipper known to date.

Titanium-silicon films prepared by spin and dip-coating

International Nuclear Information System (INIS)

Nassar, Eduardo J.; Ciuffi, Katia J.; Goncalves, Rogeria R.; Messaddeq, Younes; Ribeiro, Sidney J.L.

2003-01-01

The conditions for the preparation of luminescent materials, consisting of Eu 3+ ions entrapped in a titanium matrix, in the form of a thin film, using the sol-gel process, are described. The films were obtained from sols prepared with TEOS and TEOT, in the presence of acetylacetone as the hydrolysis-retarding agent, using the dip-coating and spin-coating techniques. The influence of these techniques on the films based on titanium and silicon are presented. The Eu 3+ was used as a luminescent probe. The films have been characterized by luminescence, reflection and transmittance. The thickness of the films could be related to the preparation procedure. Transparent thin films have been prepared by dip-coating technique. (author)

TEM analysis and wear resistance of the ceramic coatings on Q235 steel prepared by hybrid method of hot-dipping aluminum and plasma electrolytic oxidation

Energy Technology Data Exchange (ETDEWEB)

Lu Lihong [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Science and Research Department, Chinese People' s Armed Police Academy, Langfang 065000 (China); Zhang Jingwu [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Shen Dejiu, E-mail: sdj217@ysu.edu.cn [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Wu Lailei; Jiang Guirong [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Li Liang [State Key Laboratory of Automotive Safety and Energy, Tsinghua University, Beijing 100084 (China)

2012-01-25

Highlights: Black-Right-Pointing-Pointer Transmission electron microscopy (TEM) was firstly used to analyze the phase composition of the ceramic coatings. Black-Right-Pointing-Pointer The phase composition of the ceramic coatings is mainly amorphous phase and crystal Al{sub 2}O{sub 3} oxides. Black-Right-Pointing-Pointer The cross-section micro-hardness of the treated samples was investigated, the hardness of the ceramic coatings is about HV1300. Black-Right-Pointing-Pointer The wear resistance of the PEO samples is about 3 times higher than that of the heat treated 45 steel. - Abstract: The hybrid method of PEO and hot-dipping aluminum (HDA) was employed to deposit composite ceramic coatings on the surface of Q235 steel. The composition of the composite coatings was investigated with X-ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The cross-section microstructure and micro-hardness of the treated specimens were investigated and analyzed with scanning electron microscopy (SEM) and microscopic hardness meter (MHM), respectively. The wear resistance of the ceramic coatings was investigated by a self-made rubbing wear testing machine. The results indicate that metallurgical bonding can be observed between the ceramic coatings and the steel substrate. There are many micro-pores and micro-cracks, which act as the discharge channels and result of quick and non-uniform cooling of melted sections in the plasma electrolytic oxidation ceramic coatings. The phase composition of the ceramic coatings is mainly composed of amorphous phase and crystal Al{sub 2}O{sub 3} oxides. The crystal Al{sub 2}O{sub 3} phase includes {kappa}-Al{sub 2}O{sub 3}, {theta}-Al{sub 2}O{sub 3} and {beta}-Al{sub 2}O{sub 3}. The grain size of the {kappa}-Al{sub 2}O{sub 3} crystal is quite non-uniform. The hardness of the ceramic coatings is about HV1300 and 10 times higher than that of the Q235 substrate, which was favorable to the better wear resistance of the ceramic

The Association of Pediatric Obesity With Nocturnal Non-Dipping on 24-Hour Ambulatory Blood Pressure Monitoring.

Science.gov (United States)

Macumber, Ian R; Weiss, Noel S; Halbach, Susan M; Hanevold, Coral D; Flynn, Joseph T

2016-05-01

Obesity has been linked with abnormal nocturnal dipping of blood pressure (BP) in adults, which in turn is associated with poor cardiovascular outcomes. There are few data regarding abnormal dipping status in the obese pediatric population. The goal of this study was to further describe the relationship between obesity and non-dipping status on ambulatory blood pressure monitor (ABPM) in children. We conducted a cross-sectional study using a database of patients aged 5-21 years who had undergone 24-hour ABPM at Seattle Children's Hospital from January 2008 through May 2014. Subjects were grouped by body mass index (BMI) into lean (BMI 15th-85th percentile) and obese (BMI >95th percentile) groups. Compared to lean subjects (n = 161), obese subjects (n = 247) had a prevalence ratio (PR) for non-dipping of 2.15, adjusted for race (95% confidence interval (CI) = 1.25-3.42). Increasing severity of obesity was not further associated with nocturnal non-dipping. Nocturnal non-dipping was not associated with left ventricular hypertrophy (PR = 1.01, 95% CI = 0.71-1.44). These results suggest that in children, just as in adults, obesity is related to a relatively decreased dipping in nocturnal BP. © American Journal of Hypertension, Ltd 2015. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Detecting Power Voltage Dips using Tracking Filters - A Comparison against Kalman

Directory of Open Access Journals (Sweden)

STANCIU, I.-R.

2012-11-01

Full Text Available Due of its significant economical impact, Power-Quality (PQ analysis is an important domain today. Severe voltage distortions affect the consumers and disturb their activity. They may be caused by short circuits (in this case the voltage drops significantly or by varying loads (with a smaller drop. These two types are the PQ currently issues. Monitoring these phenomena (called dips or sags require powerful techniques. Digital Signal Processing (DSP algorithms are currently employed to fulfill this task. Discrete Wavelet Transforms, (and variants, Kalman filters, and S-Transform are currently proposed by researchers to detect voltage dips. This paper introduces and examines a new tool to detect voltage dips: the so-called tracking filters. Discovered and tested during the cold war, they can estimate a parameter of interest one-step-ahead based on the previously observed values. Two filters are implemented. Their performance is assessed by comparison against the Kalman filter?s results.

Hyperuricemia and non-dipping blood pressure

Directory of Open Access Journals (Sweden)

Marrone O

2013-12-01

Full Text Available Oreste Marrone,1 Maria Rosaria Bonsignore1,21National Research Council, Institute of Biomedicine and Molecular Immunology, Palermo, Italy; 2Biomedical Department of Internal and Specialistic Medicine, University of Palermo, Palermo, ItalyThe strong association between the metabolic derangements that characterize the metabolic syndrome with arterial hypertension is very well-known, as it is the common finding of hyperuricemia in the patients with the metabolic syndrome. Besides, hyperuricemia has been found to be associated with cardiovascular, renal, and metabolic diseases; including not only gout but also type 2 diabetes mellitus, although its role as a risk factor is still debated.1 We were not aware of previous studies describing an association between uric acid levels and the non-dipping 24-hour blood pressure (BP pattern, and for that reason we were intrigued by Tutal et al’s article, regarding hypertensive patients with the metabolic syndrome.2 The authors explain some possible causes that could determine an increase in uric acid in the metabolic syndrome, and describe some pathogenetic mechanisms of systemic hypertension in their patients. We would like to point out one more possible mechanism that could link hyperuricemia to non-dipping BP.View original paper by Tutal et al

40 CFR 438.2 - General definitions.

Science.gov (United States)

2010-07-01

...; galvanizing/hot dip coating; hot dip coating; kerfing; laminating; mechanical and vapor plating; metallic... machining; vacuum impregnation; vacuum plating; water shedder; wet air pollution control; wire galvanizing...

Enhanced Lamb dip for absolute laser frequency stabilization

Science.gov (United States)

Siegman, A. E.; Byer, R. L.; Wang, S. C.

1972-01-01

Enhanced Lamb dip width is 5 MHz and total depth is 10 percent of peak power. Present configuration is useful as frequency standard in near infrared. Technique extends to other lasers, for which low pressure narrow linewidth gain tubes can be constructed.

Electrochemical properties of dip-coated vanadium pentaoxide thin ...

Indian Academy of Sciences (India)

based on Helmholtz's double-layer capacitance, which is formed on an ... hybrid electric vehicles, laser, fuel cells, cellular phones, digital camera, etc. [5]. ... preparation of V2O5 by dip coating [43], but no work is found in the literature regarding ...

Associations of Blood Pressure Dipping Patterns With Left Ventricular Mass and Left Ventricular Hypertrophy in Blacks: The Jackson Heart Study.

Science.gov (United States)

Abdalla, Marwah; Caughey, Melissa C; Tanner, Rikki M; Booth, John N; Diaz, Keith M; Anstey, D Edmund; Sims, Mario; Ravenell, Joseph; Muntner, Paul; Viera, Anthony J; Shimbo, Daichi

2017-04-05

Abnormal diurnal blood pressure (BP), including nondipping patterns, assessed using ambulatory BP monitoring, have been associated with increased cardiovascular risk among white and Asian adults. We examined the associations of BP dipping patterns (dipping, nondipping, and reverse dipping) with cardiovascular target organ damage (left ventricular mass index and left ventricular hypertrophy), among participants from the Jackson Heart Study, an exclusively black population-based cohort. Analyses included 1015 participants who completed ambulatory BP monitoring and had echocardiography data from the baseline visit. Participants were categorized based on the nighttime to daytime systolic BP ratio into 3 patterns: dipping pattern (≤0.90), nondipping pattern (>0.90 to ≤1.00), and reverse dipping pattern (>1.00). The prevalence of dipping, nondipping, and reverse dipping patterns was 33.6%, 48.2%, and 18.2%, respectively. In a fully adjusted model, which included antihypertensive medication use and clinic and daytime systolic BP, the mean differences in left ventricular mass index between reverse dipping pattern versus dipping pattern was 8.3±2.1 g/m 2 ( P pattern versus dipping pattern was -1.0±1.6 g/m 2 ( P =0.536). Compared with participants with a dipping pattern, the prevalence ratio for having left ventricular hypertrophy was 1.65 (95% CI, 1.05-2.58) and 0.96 (95% CI, 0.63-1.97) for those with a reverse dipping pattern and nondipping pattern, respectively. In this population-based study of blacks, a reverse dipping pattern was associated with increased left ventricular mass index and a higher prevalence of left ventricular hypertrophy. Identification of a reverse dipping pattern on ambulatory BP monitoring may help identify black at increased risk for cardiovascular target organ damage. © 2017 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley.

Migration using a transversely isotropic medium with symmetry normal to the reflector dip

KAUST Repository

Alkhalifah, Tariq Ali; Sava, P.

2011-01-01

A transversely isotropic (TI) model in which the tilt is constrained to be normal to the dip (DTI model) allows for simplifications in the imaging and velocity model building efforts as compared to a general TI (TTI) model. Although this model cannot be represented physically in all situations, for example, in the case of conflicting dips, it handles arbitrary reflector orientations under the assumption of symmetry axis normal to the dip. Using this assumption, we obtain efficient downward continuation algorithms compared to the general TTI ones, by utilizing the reflection features of such a model. Phase-shift migration can be easily extended to approximately handle lateral inhomogeneity using, for example, the split-step approach. This is possible because, unlike the general TTI case, the DTI model reduces to VTI for zero dip. These features enable a process in which we can extract velocity information by including tools that expose inaccuracies in the velocity model in the downward continuation process. We test this model on synthetic data corresponding to a general TTI medium and show its resilience. 2011 Tariq Alkhalifah and Paul Sava.

Migration velocity analysis using a transversely isotropic medium with tilt normal to the reflector dip

KAUST Repository

Alkhalifah, T.

2010-06-13

A transversely isotropic model in which the tilt is constrained to be normal to the dip (DTI model) allows for simplifications in the imaging and velocity model building efforts as compared to a general TTI model. Though this model, in some cases, can not be represented physically like in the case of conflicting dips, it handles all dips with the assumption of symmetry axis normal to the dip. It provides a process in which areas that meet this feature is handled properly. We use efficient downward continuation algorithms that utilizes the reflection features of such a model. For lateral inhomogeneity, phase shift migration can be easily extended to approximately handle lateral inhomogeneity, because unlike the general TTI case the DTI model reduces to VTI for zero dip. We also equip these continuation algorithms with tools that expose inaccuracies in the velocity. We test this model on synthetic data of general TTI nature and show its resilience even couping with complex models like the recently released anisotropic BP model.

Dip-coating of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) anodes for efficient polymer solar cells

International Nuclear Information System (INIS)

Huang, Like; Hu, Ziyang; Zhang, Ke; Chen, Peipei; Zhu, Yuejin

2015-01-01

The fabrication of anodes and active layers by dip-coating in indium tin oxide (ITO)-free polymer solar cells (PSCs) is investigated. A highly conductive poly(3, 4-ethylenedioxythiophene):poly(styrenesulfonate)(PEDOT:PSS) layer was used as an anode while a blend film of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61 butyric acid methyl ester (PCBM) was employed as an active layer. The transmittance and sheet resistance of dip-coated PEDOT:PSS layers prepared with different thickness were studied. These layers were integrated into PSCs. The PSCs with the dip-coated PEDOT:PSS and P3HT:PCBM films exhibited power conversion efficiencies of 3.21% and 3.03% on glass and polyethylene terephthalate substrates, respectively, comparable to those of conventional ITO-based cells. Our research results suggest the feasibility of fabricating PSCs without a traditional spin-coating process and the possibility to substitute the ITO electrodes for conducting polymer films using the facile dip-coating method. - Highlights: • ITO-free polymer solar cells (PSCs) were fabricated by dip coating method. • Highly conductive PEDOT:PSS films used as anode were prepared. • The ITO-free PSCs performance was comparable with that of the spin coated devices. • Our results suggest the possibility of replacing ITO with dip coated PEDOT:PSS

Dip-coating of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) anodes for efficient polymer solar cells

Energy Technology Data Exchange (ETDEWEB)

Huang, Like; Hu, Ziyang, E-mail: huziyang@nbu.edu.cn; Zhang, Ke; Chen, Peipei; Zhu, Yuejin, E-mail: zhuyuejin@nbu.edu.cn

2015-03-02

The fabrication of anodes and active layers by dip-coating in indium tin oxide (ITO)-free polymer solar cells (PSCs) is investigated. A highly conductive poly(3, 4-ethylenedioxythiophene):poly(styrenesulfonate)(PEDOT:PSS) layer was used as an anode while a blend film of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61 butyric acid methyl ester (PCBM) was employed as an active layer. The transmittance and sheet resistance of dip-coated PEDOT:PSS layers prepared with different thickness were studied. These layers were integrated into PSCs. The PSCs with the dip-coated PEDOT:PSS and P3HT:PCBM films exhibited power conversion efficiencies of 3.21% and 3.03% on glass and polyethylene terephthalate substrates, respectively, comparable to those of conventional ITO-based cells. Our research results suggest the feasibility of fabricating PSCs without a traditional spin-coating process and the possibility to substitute the ITO electrodes for conducting polymer films using the facile dip-coating method. - Highlights: • ITO-free polymer solar cells (PSCs) were fabricated by dip coating method. • Highly conductive PEDOT:PSS films used as anode were prepared. • The ITO-free PSCs performance was comparable with that of the spin coated devices. • Our results suggest the possibility of replacing ITO with dip coated PEDOT:PSS.

Dipping-interface mapping using mode-separated Rayleigh waves

Science.gov (United States)

Luo, Y.; Xia, J.; Xu, Y.; Zeng, C.; Miller, R.D.; Liu, Q.

2009-01-01

Multichannel analysis of surface waves (MASW) method is a non-invasive geophysical technique that uses the dispersive characteristic of Rayleigh waves to estimate a vertical shear (S)-wave velocity profile. A pseudo-2D S-wave velocity section is constructed by aligning 1D S-wave velocity profiles at the midpoint of each receiver spread that are contoured using a spatial interpolation scheme. The horizontal resolution of the section is therefore most influenced by the receiver spread length and the source interval. Based on the assumption that a dipping-layer model can be regarded as stepped flat layers, high-resolution linear Radon transform (LRT) has been proposed to image Rayleigh-wave dispersive energy and separate modes of Rayleigh waves from a multichannel record. With the mode-separation technique, therefore, a dispersion curve that possesses satisfactory accuracy can be calculated using a pair of consecutive traces within a mode-separated shot gather. In this study, using synthetic models containing a dipping layer with a slope of 5, 10, 15, 20, or 30 degrees and a real-world example, we assess the ability of using high-resolution LRT to image and separate fundamental-mode Rayleigh waves from raw surface-wave data and accuracy of dispersion curves generated by a pair of consecutive traces within a mode-separated shot gather. Results of synthetic and real-world examples demonstrate that a dipping interface with a slope smaller than 15 degrees can be successfully mapped by separated fundamental waves using high-resolution LRT. ?? Birkh??user Verlag, Basel 2009.

Influence of joint dip angle on seismic behaviors of rock foundation

International Nuclear Information System (INIS)

Yang, Lei; Gao, Yang; Jiang, Yujing; Li, Bo; Li Shucai

2012-01-01

The seismic response of rock foundation to seismic loads is an important issue to the stability and safety of nuclear power plants. Due to the fact that the discontinuities like joints existing in the rock mass govern principally the deformation and failure behaviors of the rock mass, the influence of discontinuities on the seismic behaviors of rock mass remains as one of the fundamental problems in the safety assessment of nuclear power plants. In this study, the distinct element method (DEM) and finite element method (FEM) were adopted to investigate the seismic responses of rock foundation to a real seismic wave, taking into account the effect of joint dip angle on the deformation and dynamic behaviors of rock foundation. In the DEM simulations, the intact rock has an amplification effect on the amplitudes of seismic waves, while the joints exhibit an attenuation effect on the seismic waves. In the FEM simulations, however, the attenuation effect of joints is not obvious. The dip angle of joints has strong effects on the deformation and dynamic behaviors of rock foundation, in terms that different dip angles lead to obviously different deformation and horizontal stress in the rock foundation when subjected to seismic load. When the dip angle of joints is around 60deg, the seismic velocity, displacement and stress reach the maximums. Therefore, attentions need to be paid on this factor during the seismic design of nuclear power plants. (author)

Investigation of Dip-Coating Parameters Effect on The Performance of Alumina-Polydimethylsiloxane Nanofiltration Membranes for Desalination

Directory of Open Access Journals (Sweden)

Mohammad Hadi Yousefi

2017-10-01

Full Text Available The objective of this work is to investigate the effect of dip-coating parameters on the performance of Alumina-PDMS hybrid nanofiltration membranes for water desalination. Ceramic supports used in this work were prepared with a 340 nm average pore size and 34% total porosity. The aim is to determine optimum conditions of dipping time, PDMS concentration, and withdrawal speed in order to achieve high rejection and flux values. Dip-coating parameters were considered as dipping time (60 - 120 s, withdrawal speed (5 - 15 mm/s and PDMS concentration (10 - 20 wt. %. Hybrid membranes were characterized using FE-SEM and FTIR analysis techniques. Pure water flux and salt rejection were also measured to evaluate the rejection performance. Alumina-PDMS hybrid nanofiltration membranes fabricated with dipping time = 120 s, withdrawal speed = 15 mm/s and 10 wt. % PDMS exhibited the best performance giving 30.5% rejection for NaCl and 53.8% for Na2SO4.

The role of parents, friends and teachers in adolescents' cigarette smoking and tombak dipping in Sudan.

Science.gov (United States)

El-Amin, Salma El-Tayeb; Nwaru, Bright I; Ginawi, Ibrahim; Pisani, Paola; Hakama, Matti

2011-03-01

To assess the influence of smoking and tombak (local smokeless tobacco) dipping by parents, teachers and friends on cigarette smoking and tombak dipping by school-going Sudanese adolescents. This was a school-based cross-sectional survey was conducted in 2005-2006. Logistic regression was used for the analysis. A total of 4277 Sudanese school-going adolescents (aged 11-17 years) from 23 schools who completed an anonymous self-administered questionnaire on the use of tobacco products. Main outcome measures were self-reported tobacco use during the previous month defined current tobacco use. Ever smoking, tombak dipping and other tobacco products were also considered as outcomes. After adjusting for sex, age and school grade, adolescents' smoking habits were strongly associated with the habit in their parents and friends and, more weakly, with tombak dipping by teachers. When adjusted for each other, the association with smoking in friends was unaffected and remained significant (prevalence OR (POR) of having ever smoked was 1.94, 95% CI 1.64 to 2.29; OR of being current smoker was 3.77, 95% CI 2.80 to 5.07). Tobacco smoking in friends was positively associated with adolescents ever tombak dipping (POR 1.81, 95% CI 1.41 to 2.33) and current dipping (OR 3.33, 95% CI 2.20 to 5.05). The association with parental habits was reduced but still significantly elevated. Tombak dipping by teachers was only associated with adolescents ever tobacco smoking. Tobacco use by parents, teachers and friends was associated with adolescents' tobacco habits. The influence of friends was the strongest. In developing programmes against adolescents' tobacco habits, there is need to target the influence of these 'significant others'. Sudan needs to develop and implement comprehensive anti-smoking and anti-tombak dipping legislation to reduce the growing prevalence of such habits.

A comparative study on the effects of glucose monohydrate, hot water, and sodium pyrophosphate on quality parameters and microbial flora of deboned and matured brisket.

Science.gov (United States)

Gögüs, U; Bozoglu, F; Alpas, H

2007-09-01

Organic acids, hot water (HW), and chlorine have been commonly used in carcass decontamination for years. However, it has been observed that organic acids have adverse effects on color and are corrosive, while HW is discoloring. On the other hand, glucose fermentation by lactic acid bacteria in meat during the rigor period might be effective in microbial inhibition, without producing an adverse effect on the organoleptic quality of meat. Therefore, this study has aimed at finding an alternative meat decontamination procedure without any adverse effects. In this study, briskets were treated with 6 different applications: D (+) glucose monohydrate (GM) (16.51 g/100 mL, 15%) dip, HW dip, sodium pyrophosphate (SPP) and HW dip, GM + SPP + HW, and GM + HW combined dip. Then, the results of these applications were compared. First, GM + HW and GM + SPP + HW applications indicated more inhibition on Pseudomonas spp., Coliform and total Mesophile Aerob Bacteria growth, resulting in lower acidity loss (P < 0.01). Second, additional use of SPP with GM and HW did not enhance microbial inhibition (P < 0.01). Finally and most importantly, GM, 15%, improved a and b Hunter values significantly (P < 0.01), producing a very intense red meat color that can be very attractive for meat producers and consumers.

Three cases of desquamative interstitial pneumonia (DIP

Directory of Open Access Journals (Sweden)

Tabatabaie P

1997-04-01

Full Text Available D.I.P is a rare disease. The etiology is unknown. It is characterized pathologically by massive proliferation and desquamation of alveolar cells and thickening of the alveolar walls. In our studies from 1368-73 we have three patients hospitalized earlier the prognosis would be much better. Corticosteroid and other effective drugs would be helpfull in treatment of these patients.

ICE-DIP closing workshop - Public session | 14 September

CERN Multimedia

2016-01-01

ICE-DIP, the Intel-CERN European Doctorate Industrial Program (see here), is a European Industrial Doctorate scheme (see here) led by CERN. The focus of the project, which launched in 2013, has been the development of techniques for acquiring and processing data that are relevant for the trigger and data-acquisition systems of the LHC experiments.   The results will be publicly presented in an open session on the afternoon of 14th September. Building on CERN’s long-standing relationship with Intel through CERN openlab, ICE-DIP brings together CERN, Intel and research universities to offer training to five PhD students in advanced information and communication technologies (ICT). These young researchers have been funded by the European Commission as fellows at CERN and enrolled in doctoral programmes at the National University of Ireland Maynooth and Dublin City University. They have each completed 18 month secondments at Intel locations around the world gaining in-depth experience of the v...

Viscous dipping, application to the capture of fluids in living organisms

Science.gov (United States)

Lechantre, Amandine; Michez, Denis; Damman, Pascal

Some insects, birds and mammals use flower nectar as their energy resources. For this purpose, they developed specific skills to ingest viscous fluids. Depending on the sugar content, i.e., the viscosity, different strategies are observed in vivo. Indeed, butterflies use simple suction for low viscosity nectars; hummingbirds have a tongue made from two thin flexible sheets that bend to form a tube when immersed in a fluid; other animals exhibit in contrast complex papillary structures. We focus on this last method generally used for very viscous nectars. More specifically, bees and bats possess a tongue decorated with microstructures that, according to biologists, would be optimized for fluid capture by viscous dipping. In this talk, we will discuss this assumption by comparing physical models of viscous dipping to in vivo measurements. To mimic the tongue morphology, we used various rod shapes obtained by 3D printing. The influence of the type and size of lateral microstructures was then investigated and used to build a global framework describing viscous dipping for structured rods/tongues.

Floral-dip transformation of flax (Linum usitatissimum) to generate transgenic progenies with a high transformation rate.

Science.gov (United States)

Bastaki, Nasmah K; Cullis, Christopher A

2014-12-19

Agrobacterium-mediated plant transformation via floral-dip is a widely used technique in the field of plant transformation and has been reported to be successful for many plant species. However, flax (Linum usitatissimum) transformation by floral-dip has not been reported. The goal of this protocol is to establish that Agrobacterium and the floral-dip method can be used to generate transgenic flax. We show that this technique is simple, inexpensive, efficient, and more importantly, gives a higher transformation rate than the current available methods of flax transformation. In summary, inflorescences of flax were dipped in a solution of Agrobacterium carrying a binary vector plasmid (T-DNA fragment plus the Linum Insertion Sequence, LIS-1) for 1 - 2 min. The plants were laid flat on their side for 24 hr. Then, plants were maintained under normal growth conditions until the next treatment. The process of dipping was repeated 2 - 3 times, with approximately 10 - 14 day intervals between dipping. The T1 seeds were collected and germinated on soil. After approximately two weeks, treated progenies were tested by direct PCR; 2 - 3 leaves were used per plant plus the appropriate T-DNA primers. Positive transformants were selected and grown to maturity. The transformation rate was unexpectedly high, with 50 - 60% of the seeds from treated plants being positive transformants. This is a higher transformation rate than those reported for Arabidopsis thaliana and other plant species, using floral-dip transformation. It is also the highest, which has been reported so far, for flax transformation using other methods for transformation.

Hot Deformation Behavior of Hot-Extruded AA7175 Through Hot Torsion Tests.

Science.gov (United States)

Lee, Se-Yeon; Jung, Taek-Kyun; Son, Hyeon-Woo; Kim, Sang-Wook; Son, Kwang-Tae; Choi, Ho-Joon; Oh, Sang-Ho; Lee, Ji-Woon; Hyun, Soong-Keun

2018-03-01

The hot deformation behavior of hot-extruded AA7175 was investigated with flow curves and processing maps through hot torsion tests. The flow curves and the deformed microstructures revealed that dynamic recrystallization (DRX) occurred in the hot-extruded AA7175 during hot working. The failure strain was highest at medium temperature. This was mainly influenced by the dynamic precipitation of fine rod-shaped MgZn2. The processing map determined the optimal deformation condition for the alloy during hot working.

Corrosion resistance and protection mechanism of hot-dip Zn-Al-Mg alloy coated steel sheet under accelerated corrosion environment; Yoyu Zn-Al-Mg kei gokin mekki koban no sokushin fushoku kankyoka ni okeru taishokusei toi boshoku kiko

Energy Technology Data Exchange (ETDEWEB)

Komatsu, A.; Izutani, H.; Tsujimura, T.; Ando, A.; Kittaka, T. [NKK Corp., Tokyo (Japan)

2000-08-01

Corrosion behavior of hot-dip Zn-6%Al 0-3%Mg alloy coated steel sheets in cyclic corrosion test (CCT) has been investigated. The corrosion resistance was improved with increasing Mg content in the coating layer, and the highest corrosion resistance was observed at 3% Mg. In Zn-6%Al-3%Mg alloy coated steel sheet, the formations of zinc carbonate hydroxide and zinc oxide were suppressed for longer duration compared with Zn-0.2%Al and Zn-4.5%Al-0.l%Mg alloy coated steel sheets. As a result, zinc chloride hydroxide existed stable on the surface of the coating layer. From the polarization behaviors in 5% NaCl aqueous solution after CCT, it was found that the corrosion current density of Zn-6%At-3%Mg alloy coated steel sheet was much smaller than those of Zn-0.2%Al and Zn-4.5%Al-0.1%Mg alloy coated steel sheets. As zinc carbonate hydroxide and zinc oxide had poor adhesion to the coating layer and had porous structures, these corrosion products were considered to have little protective action for the coating layer. Therefore, it was concluded that Mg suppressed the formation of such nonprotective corrosion products. resulting in the remarkable improvement of corrosion resistance. (author)

Ni-YSZ graded coatings produced by dipping

International Nuclear Information System (INIS)

Ferrari, B.; Moreno, R.

2004-01-01

A new colloidal processing route for the shaping of a graded Ni-YSZ composite for applications in SOFC devices is described. A Ni foil is coated by Ni/YSZ layers by dipping in aqueous suspensions with an organic binder. Behind the metal-ceramic layers introduced to improve adhesion, an outer thin layer of nanosized YSZ is formed by electrophoretic deposition. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

9 CFR 73.10 - Permitted dips; substances allowed.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Permitted dips; substances allowed. 73.10 Section 73.10 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT... flowers of sulphur or sulphur flour to 100 gallons of water; or a specifically permitted proprietary brand...

Influence of dipping cycles on physical, optical, and electrical properties of Cu 2 NiSnS 4 : Direct solution dip coating for photovoltaic applications

Energy Technology Data Exchange (ETDEWEB)

Mokurala, Krishnaiah; Mallick, Sudhanshu; Bhargava, Parag; Siol, Sebastian; Klein, Talysa R.; van Hest, Maikel F. A. M.

2017-11-01

Direct solution coating technique has emerged as a promising economically viable process for earth abundant chalcogenide absorber materials for photovoltaic applications. Here, direct ethanol based dip coating of earth abundant Cu2NiSnS4 (CNTS) films on soda lime glass (SLG), molybdenum coated glass (Mo), and fluorine doped tin oxide coated glass (FTO) substrates is investigated. The structural and morphological properties of pre-annealed and sulfurized CNTS films coated on SLG, FTO, and Mo substrates are reported. The influence of dipping cycles on composition and optoelectronic properties of pre-annealed and sulfurized CNTS films deposited on SLG substrate is presented. Energy dispersive spectroscopy (EDS) and X-ray fluorescence (XRF) analysis reveal how changes in thickness and elemental composition affect morphology and optoelectronic properties. The obtained absorption coefficient, optical bandgap, resistivity and mobility of pre - annealed and sulfurized films are found to be 104 cm-1, 1.5 eV, 0.48 Ocm, 3.4 cm2/Vs and 104 cm-1, 1.29 eV, 0.14 Ocm, 11.0 cm2/Vs, respectively. These properties are well suited for photovoltaic applications and lead to the conclusion that the direct ethanol based dip coating can be an alternative economically viable process for the fabrication of earth abundant CNTS absorber layers for thin film solar cells.

Overall model of the dynamic behaviour of the steel strip in an annealing heating furnace on a hot-dip galvanizing line

Directory of Open Access Journals (Sweden)

Fernández, R.

2010-10-01

Full Text Available Predicting the temperature of the steel strip in the annealing process in a hot-dip galvanizing line (HDGL is important to ensure the physical properties of the processed material. The development of an accurate model that is capable of predicting the temperature the strip will reach according to the furnace’s variations in temperature and speed, its dimensions and the steel’s chemical properties, is a requirement that is being increasingly called for by industrial plants of this nature. This paper presents a comparative study made between several types of algorithms of Data Mining and Artificial Intelligence for the design of an efficient and overall prediction model that will allow determining the strip’s variation in temperature according to the physico-chemical specifications of the coils to be processed, and fluctuations in temperature and speed that are recorded within the annealing process. The ultimate goal is to find a model that is effectively applicable to coils of new types of steel or sizes that are being processed for the first time. This model renders it possible to fine-tune the control model in order to standardise the treatment in areas of the strip in which there is a transition between coils of different sizes or types of steel.La predicción de la temperatura de la banda de acero dentro del proceso de recocido de una planta de galvanizado continuo en caliente es importante para garantizar las propiedades físicas del material procesado. El desarrollo de un modelo preciso que sea capaz de predecir la temperatura que va a alcanzar la banda según las variaciones de temperaturas y velocidades del horno, y sus dimensiones y propiedades químicas del acero, es una necesidad cada vez más demandada por este tipo de plantas industriales. En el presente estudio se muestra una comparativa realizada entre diversos tipos de algoritmos deMinería de Datos e Inteligencia Artificial para el desarrollo de un modelo de predicci

The state of the art of the development of SMES for bridging instantaneous voltage dips in Japan

Science.gov (United States)

Nagaya, Shigeo; Hirano, Naoki; Katagiri, Toshio; Tamada, Tsutomu; Shikimachi, Koji; Iwatani, Yu; Saito, Fusao; Ishii, Yusuke

2012-12-01

Development of apparatuses for protecting industrial facilities such as semiconductor plants or information industries from instantaneous voltage dips, which requires very large output power, has been expected. A Superconducting magnetic energy storage system (SMES), one of such apparatus, consists of superconducting magnets that must withstand high voltage during operation and require high reliability. We have already development of SMES using conventional superconducting coils and done the field test of the SMES for bridging instantaneous voltage dips. After field test, the commercial SMES for instantaneous voltage dips is working there. Since field test has started, we have confirmed nearly 40 operations, and all have succeeded. In 2011, three commercial SMES units for bridging instantaneous voltage dips are operating in Japan.

LongerLife products increase the sustainability. Is corrosion protection ecologically useful for steel components?; LongerLife-Produkte erhoehen die Nachhaltigkeit. Ist Korrosionsschutz von Stahlbauteilen oekologisch sinnvoll?

Energy Technology Data Exchange (ETDEWEB)

Rogall, Armin Dietmar [Fachhochschule Dortmund (Germany). Fachbereich Architektur

2011-07-01

The installation of hot-dip galvanized construction units means sustainable acting. Since corrosion protection by hot-dip galvanizing can be particularly named sustainable due to its longevity, its environmental careful production, its recycling ability and life extension of steel components. Particularly the reduction of the maintenance cycles and utilization costs accompanying with a slightly higher initial investment makes the hot-dip galvanizing a sustainable system. Steel components which are treated with galvanization and colour coating, have a maintenance-free life span of more than 80 years.

Apex Dips of Experimental Flux Ropes: Helix or Cusp?

Energy Technology Data Exchange (ETDEWEB)

Wongwaitayakornkul, Pakorn; Haw, Magnus A.; Bellan, Paul M. [Applied Physics, California Institute of Technology, Pasadena, CA 91125 (United States); Li, Hui [Theoretical Division, Los Alamos National Laboratory, Mail Stop B227, Los Alamos, NM 87545 (United States); Li, Shengtai, E-mail: pwongwai@caltech.edu, E-mail: mhaw@caltech.edu [Mathematical Modeling and Analysis, Los Alamos National Laboratory, Mail Stop B284, Los Alamos, NM 87545 (United States)

2017-10-20

We present a new theory for the presence of apex dips in certain experimental flux ropes. Previously such dips were thought to be projections of a helical loop axis generated by the kink instability. However, new evidence from experiments and simulations suggest that the feature is a 2D cusp rather than a 3D helix. The proposed mechanism for cusp formation is a density pileup region generated by nonlinear interaction of neutral gas cones emitted from fast-gas nozzles. The results indicate that density perturbations can result in large distortions of an erupting flux rope, even in the absence of significant pressure or gravitational forces. The density pileup at the apex also suppresses the m = 1 kink mode by acting as a stationary node. Consequently, more accurate density profiles should be considered when attempting to model the stability and shape of solar and astrophysical flux ropes.

The efficiency of Arabidopsis thaliana floral dip transformation is determined not only by the Agrobacterium strain used but also by the physiology and the ecotype of the dipped plant.

Science.gov (United States)

Ghedira, Rim; De Buck, Sylvie; Nolf, Jonah; Depicker, Ann

2013-07-01

To evaluate the chromosomal background of different Agrobacterium strains on floral dip transformation frequency, eight wild-type Agrobacterium strains, provided by Laboratorium voor Microbiologie Gent (LMG) and classified in different genomic groups, were compared with the commonly used Agrobacterium strains C58C1 Rif(r) (pMP90) and LBA4404 in Arabidopsis thaliana Columbia (Col-0) and C24 ecotypes. The C58C1 Rif(r) chromosomal background in combination with the pMP90 virulence plasmid showed high Col-0 floral dip transformation frequencies (0.76 to 1.57%). LMG201, which is genetically close to the Agrobacterium C58 strain, with the same virulence plasmid showed comparable or even higher transformation frequencies (1.22 to 2.28%), whereas the LBA4404 strain displayed reproducibly lower transformation frequencies (Agrobacterium chromosomal backgrounds had transformation frequencies between those of the C58C1 Rif(r) (pMP90) and LBA4404 reference strains. None of the strains could transform the C24 ecotype with a frequency higher than 0.1%. Strikingly, all Arabidopsis Col-0 floral dip transformation experiments showed a high transformation variability from plant to plant (even more than 50-fold) within and across the performed biological repeats for all analyzed Agrobacterium strains. Therefore, the physiology of the plant and, probably, the availability of competent flowers to be transformed determine, to a large extent, floral dip transformation frequencies.

Three Least-Squares Minimization Approaches to Interpret Gravity Data Due to Dipping Faults

Science.gov (United States)

Abdelrahman, E. M.; Essa, K. S.

2015-02-01

We have developed three different least-squares minimization approaches to determine, successively, the depth, dip angle, and amplitude coefficient related to the thickness and density contrast of a buried dipping fault from first moving average residual gravity anomalies. By defining the zero-anomaly distance and the anomaly value at the origin of the moving average residual profile, the problem of depth determination is transformed into a constrained nonlinear gravity inversion. After estimating the depth of the fault, the dip angle is estimated by solving a nonlinear inverse problem. Finally, after estimating the depth and dip angle, the amplitude coefficient is determined using a linear equation. This method can be applied to residuals as well as to measured gravity data because it uses the moving average residual gravity anomalies to estimate the model parameters of the faulted structure. The proposed method was tested on noise-corrupted synthetic and real gravity data. In the case of the synthetic data, good results are obtained when errors are given in the zero-anomaly distance and the anomaly value at the origin, and even when the origin is determined approximately. In the case of practical data (Bouguer anomaly over Gazal fault, south Aswan, Egypt), the fault parameters obtained are in good agreement with the actual ones and with those given in the published literature.

Assessment of the impact of dipped guideways on urban rail transit systems: Ventilation and safety requirements

Science.gov (United States)

1982-01-01

The ventilation and fire safety requirements for subway tunnels with dipped profiles between stations as compared to subway tunnels with level profiles were evaluated. This evaluation is based upon computer simulations of a train fire emergency condition. Each of the tunnel configurations evaluated was developed from characteristics that are representative of modern transit systems. The results of the study indicate that: (1) The level tunnel system required about 10% more station cooling than dipped tunnel systems in order to meet design requirements; and (2) The emergency ventilation requirements are greater with dipped tunnel systems than with level tunnel systems.

The effect of stratigraphic dip on brine inflow and gas migration at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Webb, S.W.; Larson, K.W.

1996-02-01

The natural dip of the Salado Formation at the Waste Isolation Pilot Plant (WIPP), although regionally only about 111, has the potential to affect brine inflow and gas-migration distances due to buoyancy forces. Current models, including those in WIPP Performance Assessment calculations, assume a perfectly horizontal repository and stratigraphy. With the addition of buoyancy forces due to the dip, brine and gas flow patterns can be affected. Brine inflow may increase due to countercurrent flow, and gas may preferentially migrate up dip. This scoping study has used analytical and numerical modeling to evaluate the impact of the dip on brine inflow and gas-migration distances at the WIPP in one, two, and three dimensions. Sensitivities to interbed permeabilities, two-phase curves, gas-generation rates, and interbed fracturing were studied

The effect of stratigraphic dip on brine inflow and gas migration at the Waste Isolation Pilot Plant

Energy Technology Data Exchange (ETDEWEB)

Webb, S.W. [Sandia National Labs., Albuquerque, NM (United States); Larson, K.W. [INTERA, Inc., Albuquerque, NM (United States)

1996-02-01

The natural dip of the Salado Formation at the Waste Isolation Pilot Plant (WIPP), although regionally only about 111, has the potential to affect brine inflow and gas-migration distances due to buoyancy forces. Current models, including those in WIPP Performance Assessment calculations, assume a perfectly horizontal repository and stratigraphy. With the addition of buoyancy forces due to the dip, brine and gas flow patterns can be affected. Brine inflow may increase due to countercurrent flow, and gas may preferentially migrate up dip. This scoping study has used analytical and numerical modeling to evaluate the impact of the dip on brine inflow and gas-migration distances at the WIPP in one, two, and three dimensions. Sensitivities to interbed permeabilities, two-phase curves, gas-generation rates, and interbed fracturing were studied.

Solar 'hot spots' are still hot

Science.gov (United States)

Bai, Taeil

1990-01-01

Longitude distributions of solar flares are not random but show evidence for active zones (or hot spots) where flares are concentrated. According to a previous study, two hot spots in the northern hemisphere, which rotate with a synodic period of about 26.72 days, produced the majority of major flares, during solar cycles 20 and 21. The more prominent of these two hot spots is found to be still active during the rising part of cycle 22, producing the majority of northern hemisphere major flares. The synodic rotation period of this hot spot is 26.727 + or - 0.007 days. There is also evidence for hot spots in the southern hemisphere. Two hot spots separated by 180 deg are found to rotate with a period of 29.407 days, with one of them having persisted in the same locations during cycles 19-22 and the other, during cycles 20-22.

The Interplay between Gaze Following, Emotion Recognition, and Empathy across Adolescence; a Pubertal Dip in Performance?

NARCIS (Netherlands)

van Rooijen, R.; Junge, C.M.M.; Kemner, C.

2018-01-01

During puberty a dip in face recognition is often observed, possibly caused by heightened levels of gonadal hormones which in turn affects the re-organization of relevant cortical circuitry. In the current study we investigated whether a pubertal dip could be observed in three other abilities

The potential of postharvest silicon dips to regulate phenolics in ...

African Journals Online (AJOL)

ACCI

2013-03-27

Mar 27, 2013 ... This study investigated the ability of silicon dips to enhance the phenolic content in order to .... observed under a scanning electron microscope equipped with. EDX detector (Zeiss EVO LS15, Oxford XMax detector, and INCA.

Non-dipping blood pressure patterns and arterial stiffness parameters in patients with Behcet's disease.

Science.gov (United States)

Celik, Gulperi; Yilmaz, Sema; Ergulu Esmen, Serpil

2015-12-01

Behcet's disease is a multisystemic vasculitis involving veins and arteries of various sizes. Non-dipping status, augmentation index and pulse wave velocity are important determinants of cardiovascular mortality and morbidity. We investigated the non-dipping status and arterial stiffness in patients with Behcet's disease. In this cross-sectional study, we examined the vascular parameters of 96 patients with Behcet's disease (53% female) and 60 age- and sex-matched control subjects. The non-dipping status and arterial distensibility were assessed using a Mobil-O-Graph Arteriograph, an automatic oscillometric device. In total, 65.6% of 96 patients were systolic non-dippers, and 34.4% exhibited high augmentation indices. Ten percent of the control subjects were systolic non-dippers, and 11.7% exhibited high augmentation indices. Nocturnal decreases in systolic blood pressure correlated with central systolic blood pressure and diastolic blood pressure, as well as nocturnal decreases in diastolic blood pressure. Furthermore, non-dipper patients with Behcet's disease exhibited higher nocturnal cardiac outputs than did dipper patients with Behcet's disease. Augmentation index correlated negatively with C-reactive protein and correlated positively with both 24 h and nocturnal peripheral resistance, as well as 24 h pulse wave velocity. The patients with high augmentation indices exhibited lower creatinine clearance, as well as lower nocturnal cardiac outputs, higher 24 h peripheral resistance and higher 24 h pulse wave velocities. Non-dipping status and arterial stiffness may exacerbate the harmful cardiovascular effects of the other. In addition to conventional risk factors, non-dipping status and arterial stiffness should be examined during the follow-up evaluations of patients with Behcet's disease.

Performance of Doubly-Fed Wind Power Generators During Voltage Dips

DEFF Research Database (Denmark)

Aparicio, N.; Chen, Zhe; Beltran, H.

The growing of wind generation in Spain has forced its Transmission System Operator (TSO) to release new requirements that establish the amount of reactive power that a wind turbine has to supply to the grid during a voltage dip. Wind turbines equipped with doubly-fed induction generators (DFIG......) can regulate easily the reactive power generated in steady state. However, difficulties appear when reactive power has to be generated during voltage dips. Simulations have been carried out in order to check whether DFIG wind turbines can fulfill the reactive power requirements. Protection system...... commonly employed with DFIG in order to achieve ride-through capabilities including crowbar plays an important role to meet the requirements together with grid-side converter. Resistance associated with the crowbar and its connection duration are crucial at the beginning of the fault. Grid-side converter...

Cultural differences in ant-dipping tool length between neighbouring chimpanzee communities at Kalinzu, Uganda.

Science.gov (United States)

Koops, Kathelijne; Schöning, Caspar; Isaji, Mina; Hashimoto, Chie

2015-07-22

Cultural variation has been identified in a growing number of animal species ranging from primates to cetaceans. The principal method used to establish the presence of culture in wild populations is the method of exclusion. This method is problematic, since it cannot rule out the influence of genetics and ecology in geographically distant populations. A new approach to the study of culture compares neighbouring groups belonging to the same population. We applied this new approach by comparing ant-dipping tool length between two neighbouring communities of chimpanzees (Pan troglodytes schweinfurthii) in the Kalinzu Forest, Uganda. Ant-dipping tool length varies across chimpanzee study sites in relation to army ant species (Dorylus spp.) and dipping location (nest vs. trail). We compared the availability of army ant species and dipping tool length between the two communities. M-group tools were significantly longer than S-group tools, despite identical army ant target species availabilities. Moreover, tool length in S-group was shorter than at all other sites where chimpanzees prey on epigaeic ants at nests. Considering the lack of ecological differences between the two communities, the tool length difference appears to be cultural. Our findings highlight how cultural knowledge can generate small-scale cultural diversification in neighbouring chimpanzee communities.

Solar hot spots are still hot

International Nuclear Information System (INIS)

Bai, T.

1990-01-01

Longitude distributions of solar flares are not random but show evidence for active zones (or hot spots) where flares are concentrated. According to a previous study, two hot spots in the northern hemisphere, which rotate with a synodic period of about 26.72 days, produced the majority of major flares, during solar cycles 20 and 21. The more prominent of these two hot spots is found to be still active during the rising part of cycle 22, producing the majority of northern hemisphere major flares. The synodic rotation period of this hot spot is 26.727 + or - 0.007 days. There is also evidence for hot spots in the southern hemisphere. Two hot spots separated by 180 deg are found to rotate with a period of 29.407 days, with one of them having persisted in the same locations during cycles 19-22 and the other, during cycles 20-22. 14 refs

2-D deformation of two welded half-spaces due to a blind dip-slip fault

Indian Academy of Sciences (India)

The solution of two-dimensional problem of an interface breaking long inclined dip-slip fault in two welded half-spaces is well known.The purpose of this note is to obtain the corresponding solution for a blind fault.The solution is valid for arbitrary values of the fault-depth and the dip angle.Graphs showing the variation of the ...

HOT 2015

DEFF Research Database (Denmark)

Hannibal, Sara Stefansen

2016-01-01

HOT samler og formidler 21 literacykyndiges bud på, hvad der er hot, og hvad der bør være hot inden for literacy – og deres begrundelser for disse bud.......HOT samler og formidler 21 literacykyndiges bud på, hvad der er hot, og hvad der bør være hot inden for literacy – og deres begrundelser for disse bud....

Morphology evaluation of ZrO2 dip coating on mild steel and its corrosion performance in NaOH solution

Science.gov (United States)

Anwar, M. A.; Kurniawan, T.; Asmara, Y. P.; Harun, W. S. W.; Oumar, A. N.; Nandyanto, A. B. D.

2017-10-01

In this work, the morphology of ZrO2 thin film from dip coating process on mild steel has been investigated. Mild steel was dip-coated on solution made of zirconium butoxide as a precursor, ethanol as solvent, acetylacetone as chelating agent and water for hydrolysis. Number of dipping was adjusted at 3, 5 and 7 times. The dipped sample then annealed at 350°C for two hours by adjusting the heating rate at 1°C/min respectively. The optical microscope showed that micro-cracks were observed on the surface of the coating with its concentration reduced as dipping sequence increased. The XRD result showed that annealing process can produce polycrystalline tetragonal-ZrO2. Meanwhile, SEM image showed that the thicknesses of the ZrO2 coatings were in between 400-600 nm. The corrosion resistance of uncoated and coated substrates was studied by polarization test through potentio-dynamic polarization curve at 1mV/s immersed in with 3.5% NaCl. The coating efficiency was improved as the number of layer dip coated increased, which showed improvement in corrosion protection.

Konstruksi vektor biner untuk ekspresi gen dip22 yang diisolasi dari tebu varietas M 442-51 pada tanaman

Directory of Open Access Journals (Sweden)

Wiwit Budi Widyasari

2012-02-01

Full Text Available Sugarcane is the principle plant for producing sugar in Indonesia. Water supply is one key element in the agronomy of sugarcane. Sugarcane is a high biomass crop which requires large amounts of water. Low yields of sugar observed in water stressed plants indicate that sugarcane is very sensititive to drought. A number of genes that respond to drought, salt, and cold stress at the trasnscriptional level have been reported. dip22 (drought inducible protein protein isolated from drought resistance variety M 442-51 was predicted to be a protein regulator to water stress in sugarcane. Increasing of tolerance to water stress by over expression of dip22 genes in high yield sugarcane variety hopefully will maintain sugar production. The goal of this research was to construct a binary vector for dip22 gene expression in plant. dip22 gene from mutated PCR was cloned to pGEM ® €“T Easy and transformed to Escherichia coli strain DH5a. And then, these gene was isolated again from pGEM ® €“T Easy-dip22 (pGdip plasmid using restriction enzymes NcoI and PmlI. pCAMBIA 1303 plasmid is an expression vector which has the constitutive promoter CaMV35S. Recombinant plasmid was transformed to Escherichia coli strain DH5a for plasmid propagation through DNA replication. Recombinant plasmid was isolated, and digested with NcoI and PmlI to examine the presence of dip22 gene in the pCAMBIA 1303 plasmid. The recombinant plasmid was transformed to A. tumefaciens strain LBA 4404. Plasmid isolated from A. tumefaciens was digested with Bst XI and Bst EII to examine the similarity between pCAMBIA 1303-dip22 (pCdip from Escherichia coli and A. tumefaciens. The result by electrophoresis showed that both plasmids had the same size after digested. It was concluded that the transformed A. tumefaciens strain LBA 4404 bacteria has pCAMBIA 1303-dip22 (pCdip plasmid indeed. Therefore, this construct of dip22 gene in binary vector can be used for improving drought tolerance in

Gluten-Free Recipes

Science.gov (United States)

... Tofu and Shrimp Curry Irish Soda Bread Jalapeño Poppers Key Lime Pie Key Lime Pie Shooters Knorr’s ... Dill Dip Gruyere Crustinis Hot Chili Dip Jalapeño Poppers Knorr’s Vegetable Dip Lemon Dipping Sauce Meatballs for ...

Dia-Interacting Protein (DIP) Imposes Migratory Plasticity in mDia2-Dependent Tumor Cells in Three-Dimensional Matrices

Science.gov (United States)

Wyse, Meghan M.; Lei, Jun; Nestor-Kalinoski, Andrea L.; Eisenmann, Kathryn M.

2012-01-01

Tumor cells rely upon membrane pliancy to escape primary lesions and invade secondary metastatic sites. This process relies upon localized assembly and disassembly cycles of F-actin that support and underlie the plasma membrane. Dynamic actin generates both spear-like and bleb structures respectively characterizing mesenchymal and amoeboid motility programs utilized by metastatic cells in three-dimensional matrices. The molecular mechanism and physiological trigger(s) driving membrane plasticity are poorly understood. mDia formins are F-actin assembly factors directing membrane pliancy in motile cells. mDia2 is functionally coupled with its binding partner DIP, regulating cortical actin and inducing membrane blebbing in amoeboid cells. Here we show that mDia2 and DIP co-tether to nascent blebs and this linkage is required for bleb formation. DIP controls mesenchymal/amoeboid cell interconvertability, while CXCL12 induces assembly of mDia2:DIP complexes to bleb cortices in 3D matrices. These results demonstrate how DIP-directed mDia2-dependent F-actin dynamics regulate morphological plasticity in motile cancer cells. PMID:23024796

Dia-interacting protein (DIP imposes migratory plasticity in mDia2-dependent tumor cells in three-dimensional matrices.

Directory of Open Access Journals (Sweden)

Meghan M Wyse

Full Text Available Tumor cells rely upon membrane pliancy to escape primary lesions and invade secondary metastatic sites. This process relies upon localized assembly and disassembly cycles of F-actin that support and underlie the plasma membrane. Dynamic actin generates both spear-like and bleb structures respectively characterizing mesenchymal and amoeboid motility programs utilized by metastatic cells in three-dimensional matrices. The molecular mechanism and physiological trigger(s driving membrane plasticity are poorly understood. mDia formins are F-actin assembly factors directing membrane pliancy in motile cells. mDia2 is functionally coupled with its binding partner DIP, regulating cortical actin and inducing membrane blebbing in amoeboid cells. Here we show that mDia2 and DIP co-tether to nascent blebs and this linkage is required for bleb formation. DIP controls mesenchymal/amoeboid cell interconvertability, while CXCL12 induces assembly of mDia2:DIP complexes to bleb cortices in 3D matrices. These results demonstrate how DIP-directed mDia2-dependent F-actin dynamics regulate morphological plasticity in motile cancer cells.

Nocturnal Hypertension and Attenuated Nocturnal Blood Pressure Dipping is Common in Pediatric Lupus

Science.gov (United States)

Campbell, J. Fallon; Swartz, Sarah J.; Wenderfer, Scott E.

2015-01-01

Hypertension is an important manifestation of systemic lupus erythematosus (SLE) but reports of prevalence vary between 20-70% in published reports of adult and pediatric patients. For both children and adults with SLE, the clinical diagnosis and management of hypertension has traditionally been based on guidelines developed for the general population. In clinical trials, the criteria used for defining participants with hypertension are mostly undefined. As a first step towards formally assessing the blood pressure (BP) patterns of children diagnosed with SLE, 24-hr ambulatory BP monitoring data was analyzed on clinic patients who presented with prehypertension or stage I hypertension. In this pediatric SLE cohort (n=10), 20% met daytime criteria for a diagnosis of hypertension. Patterns of BP elevation varied widely with white coat, masked, isolated systolic, and diastolic nocturnal hypertension all identified. Nocturnal hypertension was detected in 60% and attenuated nocturnal BP dipping in 90% of both hypertensive and normotensive SLE patients. In SLE patients, the median nighttime systolic and diastolic loads were 25% and 15.5% compared with median daily loads of 12.5% and 11.5%. Daytime and nighttime systolic and diastolic BP load and nocturnal dipping was compared to a control population consisting of 85 non-SLE patients under 21 years old with prehypertension or stage 1 hypertension presenting to hypertension clinic. Median systolic BP dipped 5.3 mmHg in SLE patients compared to 11.9 mmHg in non-lupus ( p-value = 0.001). Median diastolic BP dipped 12.9 mmHg versus 18.5 mmHg in non-lupus ( p-value = 0.003). Patterns of BP dysregulation in pediatric SLE merit further exploration. Children with or without SLE displaying prehypertensive or stage 1 casual BP measurements had similar rates of hypertension by ambulatory BP monitoring. However, regardless of BP diagnosis, and independent of kidney involvement, there was an increased proportion with attenuated

Influence of some additives to the kinetics of Zn-crystal growth onto continuous hot dip galvanized steel

International Nuclear Information System (INIS)

Arsovski, Angel; Sekuloski, Predrag; Georgievski, Mile; Mickovski, Jovan

2003-01-01

In this work we made attempt on determination of the gefree, of influence, of the different types of additives on zinc spangle growth during forming of zinc coating, at the process of continues hot deep galvanizing of steel strip. All investigations were made at cold rolling mill plant 'Ladna Valavnica'-Skopje - HDG line, Additives were implied manually using hand pump directly on full hard strip, just before annealing furnace. Three types of additives were used in unchanged state as well as their mixtures. Analysis of the results included macro photograph of the surface, microphotograph of the zinc coating as well as different attempts of mathematical models. During investigation all technological parameters (cleanness of the strip from the emulsion marks, temperatures of the different zones of the furnace, temperature of the molten zinc and chemical composition of the zinc pot) remained at their constant values. (Original)

HotRegion: a database of predicted hot spot clusters.

Science.gov (United States)

Cukuroglu, Engin; Gursoy, Attila; Keskin, Ozlem

2012-01-01

Hot spots are energetically important residues at protein interfaces and they are not randomly distributed across the interface but rather clustered. These clustered hot spots form hot regions. Hot regions are important for the stability of protein complexes, as well as providing specificity to binding sites. We propose a database called HotRegion, which provides the hot region information of the interfaces by using predicted hot spot residues, and structural properties of these interface residues such as pair potentials of interface residues, accessible surface area (ASA) and relative ASA values of interface residues of both monomer and complex forms of proteins. Also, the 3D visualization of the interface and interactions among hot spot residues are provided. HotRegion is accessible at http://prism.ccbb.ku.edu.tr/hotregion.

CSI 2264: CHARACTERIZING YOUNG STARS IN NGC 2264 WITH SHORT-DURATION PERIODIC FLUX DIPS IN THEIR LIGHT CURVES

Energy Technology Data Exchange (ETDEWEB)

Stauffer, John; Cody, Ann Marie; Rebull, Luisa; Plavchan, Peter; Carey, Sean [Spitzer Science Center, California Institute of Technology, Pasadena, CA 91125 (United States); McGinnis, Pauline; Alencar, Silvia H. P. [Departamento de Física—ICEx—UFMG, Av. Antônio Carlos, 6627, 30270-901, Belo Horizonte, MG (Brazil); Hillenbrand, Lynne A.; Carpenter, John [Astronomy Department, California Institute of Technology, Pasadena, CA 91125 (United States); Turner, Neal J. [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91109 (United States); Terebey, Susan [Department of Physics and Astronomy, 5151 State University Drive, California State University at Los Angeles, Los Angeles, CA 90032 (United States); Morales-Calderón, María [Centro de Astrobiología, Dpto. de Astrofísica, INTA-CSIC, PO BOX 78, E-28691, ESAC Campus, Villanueva de la Cañada, Madrid (Spain); Bouvier, Jerome; Venuti, Laura [Université de Grenoble, Institut de Planétologie et d’Astrophysique de Grenoble (IPAG), F-38000 Grenoble (France); CNRS, IPAG, F-38000 Grenoble (France); Hartmann, Lee; Calvet, Nuria [Department of Astronomy, University of Michigan, 500 Church Street, Ann Arbor, MI 48105 (United States); Micela, Giusi; Flaccomio, Ettore [INAF—Osservatorio Astronomico di Palermo, Piazza del Parlamento 1, I-90134, Palermo (Italy); Song, Inseok [Department of Physics and Astronomy, The University of Georgia, Athens, GA 30602–2451 (United States); Gutermuth, Rob, E-mail: stauffer@ipac.caltech.edu [Department of Astronomy, University of Massachusetts, Amherst, MA 01003 (United States); and others

2015-04-15

We identify nine young stellar objects (YSOs) in the NGC 2264 star-forming region with optical CoRoT light curves exhibiting short-duration, shallow periodic flux dips. All of these stars have infrared excesses that are consistent with their having inner disk walls near the Keplerian co-rotation radius. The repeating photometric dips have FWHMs generally less than 1 day, depths almost always less than 15%, and periods (3 < P < 11 days) consistent with dust near the Keplerian co-rotation period. The flux dips vary considerably in their depth from epoch to epoch, but usually persist for several weeks and, in two cases, were present in data collected in successive years. For several of these stars, we also measure the photospheric rotation period and find that the rotation and dip periods are the same, as predicted by standard “disk-locking” models. We attribute these flux dips to clumps of material in or near the inner disk wall, passing through our line of sight to the stellar photosphere. In some cases, these dips are also present in simultaneous Spitzer IRAC light curves at 3.6 and 4.5 microns. We characterize the properties of these dips, and compare the stars with light curves exhibiting this behavior to other classes of YSOs in NGC 2264. A number of physical mechanisms could locally increase the dust scale height near the inner disk wall, and we discuss several of those mechanisms; the most plausible mechanisms are either a disk warp due to interaction with the stellar magnetic field or dust entrained in funnel-flow accretion columns arising near the inner disk wall.

CSI 2264: CHARACTERIZING YOUNG STARS IN NGC 2264 WITH SHORT-DURATION PERIODIC FLUX DIPS IN THEIR LIGHT CURVES

International Nuclear Information System (INIS)

Stauffer, John; Cody, Ann Marie; Rebull, Luisa; Plavchan, Peter; Carey, Sean; McGinnis, Pauline; Alencar, Silvia H. P.; Hillenbrand, Lynne A.; Carpenter, John; Turner, Neal J.; Terebey, Susan; Morales-Calderón, María; Bouvier, Jerome; Venuti, Laura; Hartmann, Lee; Calvet, Nuria; Micela, Giusi; Flaccomio, Ettore; Song, Inseok; Gutermuth, Rob

2015-01-01

We identify nine young stellar objects (YSOs) in the NGC 2264 star-forming region with optical CoRoT light curves exhibiting short-duration, shallow periodic flux dips. All of these stars have infrared excesses that are consistent with their having inner disk walls near the Keplerian co-rotation radius. The repeating photometric dips have FWHMs generally less than 1 day, depths almost always less than 15%, and periods (3 < P < 11 days) consistent with dust near the Keplerian co-rotation period. The flux dips vary considerably in their depth from epoch to epoch, but usually persist for several weeks and, in two cases, were present in data collected in successive years. For several of these stars, we also measure the photospheric rotation period and find that the rotation and dip periods are the same, as predicted by standard “disk-locking” models. We attribute these flux dips to clumps of material in or near the inner disk wall, passing through our line of sight to the stellar photosphere. In some cases, these dips are also present in simultaneous Spitzer IRAC light curves at 3.6 and 4.5 microns. We characterize the properties of these dips, and compare the stars with light curves exhibiting this behavior to other classes of YSOs in NGC 2264. A number of physical mechanisms could locally increase the dust scale height near the inner disk wall, and we discuss several of those mechanisms; the most plausible mechanisms are either a disk warp due to interaction with the stellar magnetic field or dust entrained in funnel-flow accretion columns arising near the inner disk wall

Combined heat and power solar system

International Nuclear Information System (INIS)

Anon

2000-01-01

An Australian-designed photovoltaic (PV) power system that also supplies hot water is close to commercial release. PVs have been around for decades and solar concentrators have been efficiently heating water for nearly a century. The Australian National University, Department of Engineering - Centre for Sustainable Energy systems (CSES), has designed a domestic scale modular system that not only generates electricity but also provides concentrated thermal energy to heat water for a Solahart hot water system and is designed to be deployed into small to medium scale applications such as hospitals, schools and dwellings with an easily assembled galvanised steel frame. A market research was carried out and is envisaged that at least 7,500 units will be installed annually by the year 2005 and up to 25,000 units by 2008

Diffusion Coefficient in the Zinc Coating Shaped on the Surface of Cast Iron and Steel Alloys

Directory of Open Access Journals (Sweden)

Kopyciński D.

2015-06-01

Full Text Available The article presents the method to assess the diffusion coefficient D in the sub-layer of intermetallic phases formed during hot-dip galvanizing “Armco” iron and ductile cast iron EN-GJS-500-7. Hot-dip galvanizing is one of the most popular forms of long-term protection of Fe-C alloys against corrosion. The process for producing a protective layer of sufficient quality is closely related to diffusion of atoms of zinc and iron. The simulation consist in performed a hot-dip galvanizing in laboratory condition above Fe-C alloys, in the Department of Engineering of Cast Alloys and Composites. Galvanizing time ranged from 15 to 300 seconds. Then metallographic specimens were prepared, intermetallic layers were measured and diffusion coefficient (D were calculated. It was found that the diffusion coefficient obtained during hot-dip galvanizing “Armco” iron and zinc is about two orders of magnitude less than the coefficient obtained on ductile cast iron EN-GJS-500-7.

New measurement technique of ductility curve for ductility-dip cracking susceptibility in Alloy 690 welds

Energy Technology Data Exchange (ETDEWEB)

Kadoi, Kota, E-mail: kadoi@hiroshima-u.ac.jp [Graduate School of Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8527 (Japan); Uegaki, Takanori; Shinozaki, Kenji; Yamamoto, Motomichi [Graduate School of Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8527 (Japan)

2016-08-30

The coupling of a hot tensile test with a novel in situ observation technique using a high-speed camera was investigated as a high-accuracy quantitative evaluation method for ductility-dip cracking (DDC) susceptibility. Several types of Alloy 690 filler wire were tested in this study owing to its susceptibility to DDC. The developed test method was used to directly measure the critical strain for DDC and high temperature ductility curves with a gauge length of 0.5 mm. Minimum critical strains of 1.3%, 4.0%, and 3.9% were obtained for ERNiCrFe-7, ERNiCrFe-13, and ERNiCrFe-15, respectively. The DDC susceptibilities of ERNiCrFe-13 and ERNiCrFe-15 were nearly the same and quite low compared with that of ERNiCrFe-7. This was likely caused by the tortuosity of the grain boundaries arising from the niobium content of around 2.5% in the former samples. Besides, ERNiCrFe-13 and ERNiCrFe-15 indicated higher minimum critical strains even though these specimens include higher content of sulfur and phosphorus than ERNiCrFe-7. Thus, containing niobium must be more effective to improve the susceptibility compared to sulfur and phosphorous in the alloy system.

New measurement technique of ductility curve for ductility-dip cracking susceptibility in Alloy 690 welds

International Nuclear Information System (INIS)

Kadoi, Kota; Uegaki, Takanori; Shinozaki, Kenji; Yamamoto, Motomichi

2016-01-01

The coupling of a hot tensile test with a novel in situ observation technique using a high-speed camera was investigated as a high-accuracy quantitative evaluation method for ductility-dip cracking (DDC) susceptibility. Several types of Alloy 690 filler wire were tested in this study owing to its susceptibility to DDC. The developed test method was used to directly measure the critical strain for DDC and high temperature ductility curves with a gauge length of 0.5 mm. Minimum critical strains of 1.3%, 4.0%, and 3.9% were obtained for ERNiCrFe-7, ERNiCrFe-13, and ERNiCrFe-15, respectively. The DDC susceptibilities of ERNiCrFe-13 and ERNiCrFe-15 were nearly the same and quite low compared with that of ERNiCrFe-7. This was likely caused by the tortuosity of the grain boundaries arising from the niobium content of around 2.5% in the former samples. Besides, ERNiCrFe-13 and ERNiCrFe-15 indicated higher minimum critical strains even though these specimens include higher content of sulfur and phosphorus than ERNiCrFe-7. Thus, containing niobium must be more effective to improve the susceptibility compared to sulfur and phosphorous in the alloy system.

The potential influence of subduction zone polarity on overriding plate deformation, trench migration and slab dip angle

NARCIS (Netherlands)

Schellart, W. P.

2007-01-01

A geodynamic model exists, the westward lithospheric drift model, in which the variety of overriding plate deformation, trench migration and slab dip angles is explained by the polarity of subduction zones. The model predicts overriding plate extension, a fixed trench and a steep slab dip for

Steep-dip seismic imaging of the shallow San Andreas fault near Parkfield.

Science.gov (United States)

Hole, J A; Catchings, R D; St Clair, K C; Rymer, M J; Okaya, D A; Carney, B J

2001-11-16

Seismic reflection and refraction images illuminate the San Andreas Fault to a depth of 1 kilometer. The prestack depth-migrated reflection image contains near-vertical reflections aligned with the active fault trace. The fault is vertical in the upper 0.5 kilometer, then dips about 70 degrees to the southwest to at least 1 kilometer subsurface. This dip reconciles the difference between the computed locations of earthquakes and the surface fault trace. The seismic velocity cross section shows strong lateral variations. Relatively low velocity (10 to 30%), high electrical conductivity, and low density indicate a 1-kilometer-wide vertical wedge of porous sediment or fractured rock immediately southwest of the active fault trace.

Mechanism of force mode dip-pen nanolithography

Energy Technology Data Exchange (ETDEWEB)

Yang, Haijun, E-mail: yanghaijun@sinap.ac.cn, E-mail: swguo@sjtu.edu.cn, E-mail: wanghuabin@cigit.ac.cn [Key Laboratory for Thin Film and Microfabrication of the Ministry of Education, Research Institute of Micro/Nano Science and Technology, Shanghai Jiao Tong University, Shanghai 200240 (China); Interfacial Water Division and Key Laboratory of Interfacial Physics and Technology, Shanghai Institute of Applied Physics, CAS, Shanghai 201800 (China); Xie, Hui; Rong, Weibin; Sun, Lining [State Key Laboratory of Robotics and Systems, Harbin Institute of Technology, Harbin 150080 (China); Wu, Haixia; Guo, Shouwu, E-mail: yanghaijun@sinap.ac.cn, E-mail: swguo@sjtu.edu.cn, E-mail: wanghuabin@cigit.ac.cn [Key Laboratory for Thin Film and Microfabrication of the Ministry of Education, Research Institute of Micro/Nano Science and Technology, Shanghai Jiao Tong University, Shanghai 200240 (China); Wang, Huabin, E-mail: yanghaijun@sinap.ac.cn, E-mail: swguo@sjtu.edu.cn, E-mail: wanghuabin@cigit.ac.cn [Centre for Tetrahertz Research, Chongqing Institute of Green and Intelligent Technology, Chinese Academy of Sciences, Chongqing 400714 (China)

2014-05-07

In this work, the underlying mechanism of the force mode dip-pen nanolithography (FMDPN) is investigated in depth by analyzing force curves, tapping mode deflection signals, and “Z-scan” voltage variations during the FMDPN. The operation parameters including the relative “trigger threshold” and “surface delay” parameters are vital to control the loading force and dwell time for ink deposition during FMDPN. A model is also developed to simulate the interactions between the atomic force microscope tip and soft substrate during FMDPN, and verified by its good performance in fitting our experimental data.

Impedance of the PEP-II DIP screen

Energy Technology Data Exchange (ETDEWEB)

Ng, C -K [Stanford Linear Accelerator Center, Menlo Park, CA (United States); Weiland, T

1996-08-01

The vacuum chamber of a storage ring normally consists of periodically spaced pumping slots. The longitudinal impedance of slots are analyzed in this paper. It is found that although the broad-band impedance is tolerable, the narrow-band impedance, as a consequence of the periodicity of the slots, may exceed the stability limit given by natural damping with no feedback system on. Based on this analysis, the PEP-II distributed-ion-pump (DIP) screen uses long grooves with hidden holes cut halfway to reduce both the broad-band and narrow-band impedances. (author)

Impedance of the PEP-II DIP screen

International Nuclear Information System (INIS)

Ng, C.K.; Weiland, T.

1995-09-01

The vacuum chamber of a storage ring normally consists of periodically spaced pumping slots. The longitudinal impedance of slots are analyzed in this paper. It is found that although the broad-band impedance is tolerable, the narrow-band impedance, as a consequence of the periodicity of the slots, may exceed the stability limit given by natural damping with no feedback system on. Based on this analysis, the PEP-II distributed-ion-pump (DIP) screen uses long grooves with hidden holes cut halfway to reduce both the broad-band and narrow-band impedances

Impact of the Voltage Dips in Shipboard Microgrid Power Systems

DEFF Research Database (Denmark)

Liu, Wenzhao; Guerrero, Josep M.; Savaghebi, Mehdi

2017-01-01

Voltage and frequency transient variations are the most common power quality issues in a ship microgrid system. In this paper, the impacts of the voltage dips induced by the sudden-load of ballast pump are analyzed in detail for the ship power systems. Several relevant ship power quality standards...

Life Improvement of Pot Hardware in Continuous Hot Dipping Processes Final Report

Energy Technology Data Exchange (ETDEWEB)

Xingbo Liu

2006-01-18

The process of continuous galvanizing of rolled sheet steel includes immersion into a bath of molten zinc/aluminum alloy. The steel strip is dipped in the molten bath through a series of driving motors and rollers which control the speed and tension of the strip, with the ability to modify both the amount of coating applied to the steel as well as the thickness and width of the sheet being galvanized. There are three rolls used to guide the steel strip through the molten metal bath. The rolls that operate in the molten Zn/Al are subject to a severely corrosive environment and require frequent changing. The performance of this equipment, the metallic hardware submerged in the molten Zn/Al bath, is the focus of this research. The primary objective of this research is to extend the performance life of the metallic hardware components of molten Zn/Al pot hardware by an order of magnitude. Typical galvanizing operations experience downtimes on the order of every two weeks to change the metallic hardware submerged in the molten metal bath. This is an expensive process for industry which takes upwards of 3 days for a complete turn around to resume normal operation. Each roll bridle consists of a sink, stabilizer, and corrector roll with accompanying bearing components. The cost of the bridle rig with all components is as much as $25,000 dollars just for materials. These inefficiencies are of concern to the steel coating companies and serve as a potential market for many materials suppliers. This research effort served as a bridge between the market potential and industry need to provide an objective analytical and mechanistic approach to the problem of wear and corrosion of molten metal bath hardware in a continuous sheet galvanizing line. The approach of the investigators was to provide a means of testing and analysis that was both expeditious and cost effective. The consortium of researchers from West Virginia University and Oak Ridge National Laboratory developed

Nocturnal antihypertensive treatment in patients with type 1 diabetes with autonomic neuropathy and non-dipping

DEFF Research Database (Denmark)

Hjortkjær, Henrik Øder; Jensen, Tonny; Kofoed, Klaus F

2016-01-01

to test if bedtime dosing (BD) versus morning dosing (MD) of the ACE inhibitor enalapril would affect the 24-hour BP profile in patients with type 1 diabetes (T1D), CAN and non-dipping. SETTING: Secondary healthcare unit in Copenhagen, Denmark. PARTICIPANTS: 24 normoalbuminuric patients with T1D with CAN...... and non-dipping were included, consisting of mixed gender and Caucasian origin. Mean±SD age, glycosylated haemoglobin and diabetes duration were 60±7 years, 7.9±0.7% (62±7 mmol/mol) and 36±11 years. INTERVENTIONS: In this randomised, placebo-controlled, double-blind cross-over study, the patients were......OBJECTIVES: Cardiovascular autonomic neuropathy (CAN) and abnormal circadian blood pressure (BP) rhythm are independent cardiovascular risk factors in patients with diabetes and associations between CAN, non-dipping of nocturnal BP and coronary artery disease have been demonstrated. We aimed...

A Study of Dip-Coatable, High-Capacitance Ion Gel Dielectrics for 3D EWOD Device Fabrication

Directory of Open Access Journals (Sweden)

Carlos E. Clement

2017-01-01

Full Text Available We present a dip-coatable, high-capacitance ion gel dielectric for scalable fabrication of three-dimensional (3D electrowetting-on-dielectric (EWOD devices such as an n × n liquid prism array. Due to the formation of a nanometer-thick electric double layer (EDL capacitor, an ion gel dielectric offers two to three orders higher specific capacitance (c ≈ 10 μF/cm2 than that of conventional dielectrics such as SiO2. However, the previous spin-coating method used for gel layer deposition poses several issues for 3D EWOD device fabrication, particularly when assembling multiple modules. Not only does the spin-coating process require multiple repetitions per module, but the ion gel layer also comes in risks of damage or contamination due to handling errors caused during assembly. In addition, it was observed that the chemical formulation previously used for the spin-coating method causes the surface defects on the dip-coated gel layers and thus leads to poor EWOD performance. In this paper, we alternatively propose a dip-coating method with modified gel solutions to obtain defect-free, functional ion gel layers without the issues arising from the spin-coating method for 3D device fabrication. A dip-coating approach offers a single-step coating solution with the benefits of simplicity, scalability, and high throughput for deposition of high-capacitance gel layers on non-planar EWOD devices. An ion gel solution was prepared by combining the [EMIM][TFSI] ionic liquid and the [P(VDF-HFP] copolymer at various wt % ratios in acetone solvent. Experimental studies were conducted to fully understand the effects of chemical composition ratios in the gel solution and how varying thicknesses of ion gel and Teflon layers affects EWOD performance. The effectiveness and potentiality of dip-coatable gel layers for 3D EWOD devices have been demonstrated through fabricating 5 × 1 arrayed liquid prisms using a single-step dip-coating method. Each prism module has

Characterization of CuS nanocrystalline thin films synthesized by chemical bath deposition and dip coating techniques

International Nuclear Information System (INIS)

Chaki, Sunil H.; Deshpande, M.P.; Tailor, Jiten P.

2014-01-01

CuS thin films were synthesized by chemical bath deposition and dip coating techniques at ambient temperature. The energy dispersive analysis of X-rays of the thin films confirmed that both the as synthesized thin films are stoichiometric. The X-ray diffraction of the chemical bath deposited and dip coating deposited thin films showed that the films possess hexagonal structure having lattice parameters, a = b = 3.79 A and c = 16.34 A. The crystallite sizes determined from the X-ray diffraction data using Scherrer's formula for the chemical bath deposition and dip coating deposition thin films came out to be nearly 11 nm and 13 nm, respectively. The optical microscopy of the as deposited thin films surfaces showed that the substrates are well covered in both the deposited films. The scanning electron microscopy of the thin films clearly showed that in chemical bath deposited thin films the grain size varies from few μm to nm, while in dip coating deposited films the grain size ranges in nm. The optical bandgap determined from the optical absorbance spectrum analysis showed, chemical bath deposited thin films possess direct bandgap of 2.2 eV and indirect bandgap of 1.8 eV. In the case of dip coating deposited thin films, the direct bandgap is 2.5 eV and indirect bandgap is 1.9 eV. The d.c. electrical resistivity variation with temperature for both the deposited films showed that the resistivity decreases with temperature thus confirming the semiconducting nature. The thermoelectric power variations with temperature and the room temperature Hall Effect study of both the synthesized CuS thin films showed them to be of p-type conductivity. The obtained results are discussed in details. - Highlights: • CuS thin films were synthesized by chemical bath deposition and dip coating techniques. • The films possessed hexagonal structure. • The optical absorption showed that the films had direct and indirect bandgap. • Study of electrical transport properties

HOT 2012

DEFF Research Database (Denmark)

Lund, Henriette Romme

Undersøgelse af, hvad der er hot - og hvad der burde være hot på læseområdet med 21 læsekyndige. Undersøgelsen er gennemført siden 2010. HOT-undersøgelsen er foretaget af Nationalt Videncenter for Læsning - Professionshøjskolerne i samarb. med Dansklærerforeningen......Undersøgelse af, hvad der er hot - og hvad der burde være hot på læseområdet med 21 læsekyndige. Undersøgelsen er gennemført siden 2010. HOT-undersøgelsen er foretaget af Nationalt Videncenter for Læsning - Professionshøjskolerne i samarb. med Dansklærerforeningen...

A dip-slide test for bacteriuria in protein-calorie malnutrition ...

African Journals Online (AJOL)

A simple dip-slide test was used to determine the incidence of bacteriuria in children suffering from protein-calorie malnutrition. Bacteriuria was found to be equally common in patients suffering from kwashiorkor and atrophic malnutrition and in a control group with normal nutritional status. The test is inexpensive and has a ...

Thermal Stress and Heat Transfer Coefficient for Ceramics Stalk Having Protuberance Dipping into Molten Metal

Science.gov (United States)

Noda, Nao-Aki; Hendra; Li, Wenbin; Takase, Yasushi; Ogura, Hiroki; Higashi, Yusuke

Low pressure die casting is defined as a net shape casting technology in which the molten metal is injected at high speeds and pressure into a metallic die. The low pressure die casting process plays an increasingly important role in the foundry industry as a low-cost and high-efficiency precision forming technique. In the low pressure die casting process is that the permanent die and filling systems are placed over the furnace containing the molten alloy. The filling of the cavity is obtained by forcing the molten metal, by means of a pressurized gas, to rise into a ceramic tube having protuberance, which connects the die to the furnace. The ceramics tube, called stalk, has high temperature resistance and high corrosion resistance. However, attention should be paid to the thermal stress when the stalk having protuberance is dipped into the molten aluminum. It is important to reduce the risk of fracture that may happen due to the thermal stresses. In this paper, thermo-fluid analysis is performed to calculate surface heat transfer coefficient. The finite element method is applied to calculate the thermal stresses when the stalk having protuberance is dipped into the crucible with varying dipping speeds. It is found that the stalk with or without protuberance should be dipped into the crucible slowly to reduce the thermal stress.

Gently dipping normal faults identified with Space Shuttle radar topography data in central Sulawesi, Indonesia, and some implications for fault mechanics

Science.gov (United States)

Spencer, J.E.

2011-01-01

Space-shuttle radar topography data from central Sulawesi, Indonesia, reveal two corrugated, domal landforms, covering hundreds to thousands of square kilometers, that are bounded to the north by an abrupt transition to typical hilly to mountainous topography. These domal landforms are readily interpreted as metamorphic core complexes, an interpretation consistent with a single previous field study, and the abrupt northward transition in topographic style is interpreted as marking the trace of two extensional detachment faults that are active or were recently active. Fault dip, as determined by the slope of exhumed fault footwalls, ranges from 4?? to 18??. Application of critical-taper theory to fault dip and hanging-wall surface slope, and to similar data from several other active or recently active core complexes, suggests a theoretical limit of three degrees for detachment-fault dip. This result appears to conflict with the dearth of seismological evidence for slip on faults dipping less than ~. 30??. The convex-upward form of the gently dipping fault footwalls, however, allows for greater fault dip at depths of earthquake initiation and dominant energy release. Thus, there may be no conflict between seismological and mapping studies for this class of faults. ?? 2011 Elsevier B.V.

Control of Polychaetes by Dipping Infected Pearl Oyster on Different Salinity

Directory of Open Access Journals (Sweden)

Yani Hadiroseyani

2007-08-01

Full Text Available Dip treatment on pearl oysters (Pinctada maxima was conducted in different concentrations of saline water to eliminate boring polychaetes. Results shows that polychaetes leave the osyters which treated on saline water at 0 ppt, 45 ppt, and 60 ppt as long as 15 minutes each. It also shows that the oysters got high survival rate 7 days after the treatment. Key words : Polychaetes, pearl oyster, dipping, salinity   ABSTRAK Pengendalian polikaeta pengebor dengan menggunakan berbagai konsentrasi larutan garam telah dilakukan pada tiram mutiara (Pinctada maxima. Berdasarkan jumlah polikaeta yang keluar, hasil percobaan ini menunjukkan bahwa perendaman dengan konsentrasi garam 0 ppt. 45 ppt, dan 60 ppt selama 15 menit lebih efektif dibandingkan pada konsentrasi 15 dan 30 ppt. Tingkat kelangsungan hidup tiram mutiara yang diamati 7 hari setelah perendaman dalam larutan garam mencapai 100%. Kata kunci : Polikaeta. tiram mutiara, perendaman. salinitas

Observation of variable pre-eclipse dips and disk winds in the eclipsing LMXB XTE J1710-281

Science.gov (United States)

Raman, Gayathri; Maitra, Chandreyee; Paul, Biswajit

2018-04-01

We report the first detection of highly ionized Fe species in the X-ray spectrum of the eclipsing and dipping Low Mass X-ray Binary XTE J1710-281. Using archival Chandra and Suzaku observations, we have carried out a spectro-timing analysis of the source during three different epochs. We compare the average orbital profile and obtain differences in pre-eclipse dip morphologies between different observation epochs. We observe an orbit to orbit evolution of the dips for the first time in this source in both the Chandra observations, reflecting changes in the structure of the accretion disc in timescales of hours. We further perform intensity resolved spectroscopy for both the Chandra and the Suzaku data to characterize the changes in the spectral parameters from the persistent to the dipping intervals. We find that the absorbers responsible for the dips, can be best described using a partially ionized partial covering absorber, with an ionization parameter, log(ξ) of ˜2. The photon index of the source remained at ˜2 during both the Chandra and the Suzaku observations. In the 0.6-9 keV Suzaku spectra, we detect a broad 0.72 keV Fe L-alpha emission line complex and two narrow absorption lines at ˜6.60 keV and ˜7.01 keV. The highly ionized Fe line signatures, being an indicator of accretion disc-winds, has been observed for the first time in XTE J1710-281.

Environmental impact assessment for steeply dipping coal beds: North Knobs site

Energy Technology Data Exchange (ETDEWEB)

1978-11-08

The US Department of Energy is funding an underground coal gasification (UCG) project in steeply dipping coal beds (SDB), at North Knobs, about 8 miles west of Rawlins, Carbon County, Wyoming. The project is being conducted to determine the technical, economic and environmental viability of such a technology. The development of SDB is an interesting target for UCG since such beds contain coals not normally mineable economically by ordinary techniques. Although the underground gasification of SDB has not been attempted in the US, Soviet experience and theoretical work indicate that the gasification of SDB in place offers all the advantages of underground gasification of horizontal coal seams plus some unique characteristics. The steep angle of dip helps to channel the produced gases up dip to offtake holes and permits the ash and rubble to fall away from the reaction zone helping to mitigate the blocking of the reaction zone in swelling coals. The intersection of SDB with the surface makes the seam accessible for drilling and other preparation. The tests at the North Knobs site will consist of three tests, lasting 20, 80 and 80 days, respectively. A total of 9590 tons of coal is expected to be gasified, with surface facilities utilizing 15 acres of the total section of land. The environmental effects of the experiment are expected to be very small. The key environmental impact is potential groundwater contamination by reaction products from coal gasification. There is good evidence that the surrounding coal effectively blocks the migration of these contaminants.

Radioisotope labelling of several major insect pest. Dipping the pupae in /sup 32/P solution

Energy Technology Data Exchange (ETDEWEB)

Sutrisno, S. (National Atomic Energy Agency, Jakarta (Indonesia). Pasar Djumat Research Centre)

1981-12-01

Radioisotope uptake by insects could take place through various parts i.e. mouth, cuticula, intersegmental, secretion and excretion organs. Usually insects are labelled internally by feeding them on an artificial diet containing radioisotope solution. Labelling of several insect pests of cabbage (Crocidolomia binotalis) Zell and Plutella maculipennis Curt and rice (Chilo suppressalis Walker) by dipping of the pupae in /sup 32/P solution showed a promising result. Pupae of Crocidolomia binotalis Zell dipped in 3 ml solution of /sup 32/P with specific activities of 1, 3, 5 and 7 ..mu..Ci/ml had developed labelled adults of sufficiently high radioactivity levels for ecological studies. Similar results were also obtained with Plutella maculipennis Curt and Chilo suppressalis Walker with doses of 1, 3, 5, 7 and 9 ..mu..Ci/ml /sup 32/P solution. The best doses for radioisotope labelling by dipping of the insects Crocidolomia binotalis Zell, Plutella maculipennis Curt, and Chilo suppressalis Walker were 1, 9, and 7 ..mu..Ci/ml respectivelly.

Development of procedures to stabilize chlorfenvinphos in model cattle dips

International Nuclear Information System (INIS)

Pastor, Y.; Caceres, T.; Merino, R.; Villamar, P.; Castro, R.

1997-01-01

The environmental fate and dissipation of chlorfenvinphos acaricide was studied in water and sediment in model cattle dips with recharge, without recharge and with added stabilizers. Chlorfenvinphos concentration decreased with time in all of them, and the monthly recharge at 10% of the initial concentration was inefficient to maintain a concentration that would be effective for tick control. However, the loss of pesticide in the model dip with added phosphate buffer as stabilizer was the least. Volatilization was the principal factor that influenced the dissipation of the pesticide. The sediment bound residues increased with time. Mineralization of 14 C-chlorfenvinphos due to microbial activity showed that the 14 CO 2 production increased with time in biometers flasks with different amounts of sediment. 2,4-Dichloroacetophenone, and 2,4-dichlorobenzaldehyde were identified as degradation products. Isomerization of chlorfenviphos from isomer Z to E was influenced by sunlight. Chlorfenvinphos was stable in aqueous solution for 14 days under pH 4 to 9. Leaching tests demonstrated that the pesticide was not a potential pollutant of ground water. (author)

Physics properties of TiO_2 films produced by dip-coating technique

International Nuclear Information System (INIS)

Teloeken, A.C.; Alves, A.K.; Berutti, F.A.; Tabarelli, A.; Bergmann, C.P.

2014-01-01

The use of titanium dioxide (TiO_2) as a photocatalyst to produce hydrogen has been of great interest because of their chemical stability, low cost and non-toxicity. TiO_2 occurs in three different crystal forms: rutile, anatase and brokita. Among these, the anatase phase generally exhibits the best photocatalytic behavior, while the rutile phase is the most stable. Among the various techniques of deposition, dip-coating technique produces films with good photocatalytic properties, using simple and inexpensive equipment. In this work TiO_2 films were obtained by dip-coating. The films were characterized using X-ray diffraction, scanning electron microscopy, profilometry, contact angle measurements and photocurrent. The microstructure and physical properties were evaluated in relation of the temperature and the addition of an additive. (author)

Magnetic dips in the solar wind

International Nuclear Information System (INIS)

Dobrowolny, M.; Bavassano, B.; Mariani, F.; Ness, N.; Burlaga, L.

1978-09-01

With the help of magnetic data from the HELIOS 1 fluxgate magnetometer, with a 0.2 sec resolution, the structures of several interplanetary discontinuities involving magnetic dips and rotations of the magnetic field vector were investigated. A minimum variance analysis illustrates the behavior of the magnetic field through the transition in the plane of its maximum variation. By means of this analysis, quite different structures have been individuated, in particular, narrow transitions resembling almost one-dimensional reconnected neutral sheets. For the thinner cases (scale lengths of the magnetic rotation of the order or smaller than 1,000 km), results show the observed structures could be the nonlinear effect of a resistive tearing mode instability having developed on an originally one-dimensional neutral sheet at the solar corona

Endothelial perturbation: a link between non-dipping and retinopathy in type 2 diabetes?

DEFF Research Database (Denmark)

Knudsen, Søren Tang; Jeppesen, Peter; Frederiksen, Christian Alcaraz

2007-01-01

-six subjects, stratified to 4 gender-, age-, and duration-matched groups of 19 subjects each, were studied (group A: non-diabetic subjects; group B to D, type 2 diabetic subjects; group B: no retinopathy; group C: minimal background retinopathy; group D: diabetic maculopathy). All subjects underwent a 24-hour......Reduced diurnal blood pressure (BP) variation ("non-dipping") is associated with both micro- and macrovascular complications in patients with type 2 diabetes. The relation between endothelial perturbation and diurnal BP variation in diabetic subjects has not previously been studied. Seventy...... to endothelial cell activation as well as with retinopathy in subjects with type 2 diabetes. This finding suggests a possible mechanism linking non-dipping with microvascular complications in these subjects....

Large area nano-patterning /writing on gold substrate using dip - pen nanolithography (DPN)

Science.gov (United States)

Saini, Sudhir Kumar; Vishwakarma, Amit; Agarwal, Pankaj B.; Pesala, Bala; Agarwal, Ajay

2014-10-01

Dip Pen Nanolithography (DPN) is utilized to pattern large area (50μmX50μm) gold substrate for application in fabricating Nano-gratings. For Nano-writing 16-MHA ink coated AFM tip was prepared using double dipping procedure. Gold substrate is fabricated on thermally grown SiO2 substrate by depositing ˜5 nm titanium layer followed by ˜30nm gold using DC pulse sputtering. The gratings were designed using period of 800nm and 25% duty cycle. Acquired AFM images indicate that as the AFM tip proceeds for nano-writing, line width decreases from 190nm to 100nm. This occurs probably due to depreciation of 16-MHA molecules in AFM tip as writing proceeds.

Neural-net based calculation of voltage dips at maximum angular swing in direct transient stability analysis [of power systems

Energy Technology Data Exchange (ETDEWEB)

Djukanovic, M [Inst. ' Nikola Tesla' , Belgrade (Yugoslavia); Sobajic, D J; Pao, Yohhan [Case Western Reserve Univ., Cleveland, OH (United States). Dept. of Electrical Engineering and Applied Physics Case Western Reserve Univ., Cleveland, OH (United States). Dept. of Computer Engineering and Science AI WARE inc., Cleveland, OH (United States)

1992-10-01

In heavily stressed power systems, post-fault transient voltage dips can lead to undesired tripping of industrial drives and large induction motors. The lowest transient voltage dips occur when fault clearing times are less than critical ones. In this paper, we propose a new iterative analytical methodology to obtain more accurate estimates of voltage dips at maximum angular swing in direct transient stability analysis. We also propose and demonstrate the possibility of storing the results of these computations in the associative memory (AM) system, which exhibits remarkable generalization capabilities. Feature-based models stored in the AM can be utilized for fast and accurate prediction of the location, duration and the amount of the worst voltage dips, thereby avoiding the need and cost for lengthy time-domain simulations. Numerical results obtained using the example of the New England power system are presented to illustrate our approach. (Author)

Hot Flashes

Science.gov (United States)

Hot flashes Overview Hot flashes are sudden feelings of warmth, which are usually most intense over the face, neck and chest. Your skin might redden, as if you're blushing. Hot flashes can also cause sweating, and if you ...

29 CFR 1910.124 - General requirements for dipping and coating operations.

Science.gov (United States)

2010-07-01

...) The ventilation that you provide to a vapor area must keep the airborne concentration of any substance... Tanks Containing Flammable or Combustible Liquids; (iii) ACGIH's “Industrial Ventilation: A Manual of... Open-Surface Tanks, and NFPA 34-1966, Standard for Dip Tanks Containing Flammable or Combustible...

Research and development on procedures to stabilize acaricides in livestock dips. Proceedings of a final research co-ordination meeting

International Nuclear Information System (INIS)

1997-11-01

Ticks and mites are serious ectoparasites of livestock in many countries. As vectors of animal diseases they pose a threat to livestock production. Traditionally, different types of acaricides are used to control them. One of the most commonly used tick control techniques is to force animals to walk through an acaricide suspension in a trough or Cattle Dip. Dipping is quite effective as the entire body of the animal gets treated with the acaricide. However, with increased usage the concentration of the acaricide in the 'dip' declines due to removal by the animal and degradation by biological and chemicals processes. The dissipation of the acaricide results in loss of efficacy of the 'dip', and may also enhance the development of resistance by the ectoparasites to the acaricides. Maintenance of an effective concentration, by periodic recharge or stabilization of the acaricide, is essential to assure efficient and cost-effective control and to minimize chances of resistance to develop. In 1990, the FAO/IAEA Joint Division, recognizing the need for co-ordinated research on studying the dissipation of acaricides in cattle dips and developing procedures to stabilize them, established a 5-year Co-ordinated Research Programme on Development of Procedures to Stabilize Acaricides in Livestock Dips and of Simplified Methods to Measure Their Concentration, Using Nuclear Techniques. In initiating this programme, the Joint Division recognized that major gaps exist in the knowledge in this area which, if filled, would greatly aid developing countries in their effort to more effectively use acaricides to protect animal health. This TECDOC reports the accomplishments of this programme

Association of polycystic ovary syndrome and a non-dipping blood pressure pattern in young women

Directory of Open Access Journals (Sweden)

Ayse Kargili

2010-01-01

Full Text Available OBJECTIVE: The association between polycystic ovarian syndrome and increased cardiovascular disease risk is still a controversial issue. In light of data documenting some common pathways or common end-points, the present study was undertaken to determine whether there is a relationship between sleep blood pressure pattern disturbances and polycystic ovarian syndrome in young women. METHOD: The daytime and nighttime ambulatory blood pressures (BPs were determined for each subject, according to the actual waking and sleeping times recorded in their individual diaries, in this cross-sectional study. RESULTS: The study group comprised 168 women (mean age: 25.7±5.5 diagnosed with polycystic ovarian syndrome, while the control group included 52 age- and BMI-matched healthy subjects (mean age: 26.1±5.4. When nocturnal BP declines very little or not at all, with the BP falling less than 10% during sleep compared with waking values, this pattern is classified as a non-dipping BP pattern. However, the non-dipping pattern of BP changes was significantly more common in polycystic ovarian syndrome patients compared to the control group (p<0.01. The prevalence of a non-dipping BP pattern was 43.4% (73 patients in polycystic ovarian syndrome patients and 3.9% (2 patients in the control group. CONCLUSION: Our cross-sectional study revealed that a non-dipping BP pattern is highly prevalent in polycystic ovarian syndrome patients, even if they are young and non-obese.

Controlled Growth of Ultrathin Film of Organic Semiconductors by Balancing the Competitive Processes in Dip-Coating for Organic Transistors.

Science.gov (United States)

Wu, Kunjie; Li, Hongwei; Li, Liqiang; Zhang, Suna; Chen, Xiaosong; Xu, Zeyang; Zhang, Xi; Hu, Wenping; Chi, Lifeng; Gao, Xike; Meng, Yancheng

2016-06-28

Ultrathin film with thickness below 15 nm of organic semiconductors provides excellent platform for some fundamental research and practical applications in the field of organic electronics. However, it is quite challenging to develop a general principle for the growth of uniform and continuous ultrathin film over large area. Dip-coating is a useful technique to prepare diverse structures of organic semiconductors, but the assembly of organic semiconductors in dip-coating is quite complicated, and there are no reports about the core rules for the growth of ultrathin film via dip-coating until now. In this work, we develop a general strategy for the growth of ultrathin film of organic semiconductor via dip-coating, which provides a relatively facile model to analyze the growth behavior. The balance between the three direct factors (nucleation rate, assembly rate, and recession rate) is the key to determine the growth of ultrathin film. Under the direction of this rule, ultrathin films of four organic semiconductors are obtained. The field-effect transistors constructed on the ultrathin film show good field-effect property. This work provides a general principle and systematic guideline to prepare ultrathin film of organic semiconductors via dip-coating, which would be highly meaningful for organic electronics as well as for the assembly of other materials via solution processes.

Prestack traveltimes for dip-constrained TI media

KAUST Repository

Golikov, Pavel; Alkhalifah, Tariq Ali; Stovas, Alexey

2012-01-01

The double-square-root (DSR) formula is an integral part of many wavefield based imaging tools. A transversely isotropic medium with a titled symmetry axis (TI) version of the DSR formula is nearly impossible to obtain analytically. As a result, we develop an approximate version of the DSR formula valid for media with the symmetry axis normal to the dip of the reflector (DTI). The accuracy of this approximate solution is enhanced using Shanks transform to a point where the errors are extremely small for practical anisotropic values. Under this assumption, we also do not need to compute the symmetry axis field as it is inherently included in the formulation.

Prestack traveltimes for dip-constrained TI media

KAUST Repository

Golikov, Pavel

2012-11-04

The double-square-root (DSR) formula is an integral part of many wavefield based imaging tools. A transversely isotropic medium with a titled symmetry axis (TI) version of the DSR formula is nearly impossible to obtain analytically. As a result, we develop an approximate version of the DSR formula valid for media with the symmetry axis normal to the dip of the reflector (DTI). The accuracy of this approximate solution is enhanced using Shanks transform to a point where the errors are extremely small for practical anisotropic values. Under this assumption, we also do not need to compute the symmetry axis field as it is inherently included in the formulation.

Mitigation of voltage dip and power system oscillations damping using dual STATCOM for grid connected DFIG

OpenAIRE

D.V.N. Ananth; G.V. Nagesh Kumar

2017-01-01

During grid fault, transmission lines reach its thermal limit and lose its capability to transfer. If this fault current enters generator terminals, it will lead to dip in stator voltage and consequently produces torque and real power oscillations. This further affects in the form of internal heat in rotor windings and finally damages the generator. A new control strategy is proposed to limit fault current using dual STATCOM, which will damp power oscillations and mitigate the voltage dip due...

Thermoplastic polymers surfaces for Dip-Pen Nanolithography of oligonucleotides

International Nuclear Information System (INIS)

Suriano, Raffaella; Biella, Serena; Cesura, Federico; Levi, Marinella; Turri, Stefano

2013-01-01

Different thermoplastic polymers were spin-coated to prepare smooth surfaces for the direct deposition of end-group modified oligonucleotides by Dip-Pen Nanolithography. A study of the diffusion process was done in order to investigate the dependence of calibration coefficient and quality of deposited features on environmental parameters (temperature, relative humidity) and ink's molecular weight and functionality. The optimization of the process parameters led to the realization of high quality and density nanoarrays on plastics.

THE MANUFACUTE OF GLOVES USING RVNRL: PARAMETERS OF the COAGULANT DIPPING PROCESS

Directory of Open Access Journals (Sweden)

H.D. CHIRINOS

1998-12-01

Full Text Available Surgical gloves were manufactured using the RVNRL process. A fractional factorial design at two levels showed that five parameters of the coagulant dipping process which were studied independent. Coagulant concentration and dwell time in the radiovulcanized latex presented major main effects while the temperature of the former before dipping into the radiovulcanized latex and the flow time of the radiovulcanized latex on the former surface presented opposite main effects. The withdrawal rate of the former from the radiovulcanized latex did not change glove thickness. The mathematical correlation between the estimates of thickness and the significant main effects of coded variables was = 0.212 + 0.025x1 + 0.019x2. This optimized equation allowed reproduction of a surgical glove thickness in the range of 0.157 to 0.291mm, which is considered acceptable by international standard specification.

HOT 2011

DEFF Research Database (Denmark)

Lund, Henriette Romme

En undersøgelse af, hvad der er hot - og burde være hot på læseområdet. I undersøgelsen deltager 21 læsekyndige fra praksisfeltet, professionshøjskolerne og forskningsområdet.......En undersøgelse af, hvad der er hot - og burde være hot på læseområdet. I undersøgelsen deltager 21 læsekyndige fra praksisfeltet, professionshøjskolerne og forskningsområdet....

Electrochemical behaviour of silica basic hybrid coatings deposited on stainless steel by dipping and EPD

International Nuclear Information System (INIS)

Castro, Y.; Duran, A.; Damborenea, J.J.; Conde, A.

2008-01-01

The aim of this work is the characterisation of the corrosion behaviour of stainless steel (AISI 304) substrates coated by dipping and electrophoretic deposition (EPD) from a sol-gel basic sol. Particulate silica sols (labelled NaSi) were prepared by basic catalysis from ethyltriethoxysilane (TEOS), methyltriethoxysilane (MTES) and sodium hydroxide. Coatings between 2 and 10 μm were prepared by using concentrated and diluted sols by dipping and EPD process and the corrosion behaviour of the coated substrates were studied through potentiodynamic and impedance spectroscopy measurements (EIS). Potentiodynamic studies of coatings produced by dipping reveal a strong dependence of the protective properties with the concentration of the sol. This behaviour was confirmed by EIS showing that only the coatings obtained from concentrated sol present enough protective properties. On the contrary, EPD coatings prepared from diluted NaSi sol showed an excellent corrosion resistance, maintaining a pure capacitive behaviour for long periods of immersion. EPD deposition is thus proposed as a good alternative method for obtaining thicker and denser coatings with good protective properties from dilute and stable sols

Thermoplastic polymers surfaces for Dip-Pen Nanolithography of oligonucleotides

Energy Technology Data Exchange (ETDEWEB)

Suriano, Raffaella [Dipartimento di Chimica, Materiali e Ingegneria Chimica “Giulio Natta”, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milano (Italy); Biella, Serena, E-mail: serena.biella@polimi.it [Dipartimento di Chimica, Materiali e Ingegneria Chimica “Giulio Natta”, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milano (Italy); Cesura, Federico; Levi, Marinella; Turri, Stefano [Dipartimento di Chimica, Materiali e Ingegneria Chimica “Giulio Natta”, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milano (Italy)

2013-05-15

Different thermoplastic polymers were spin-coated to prepare smooth surfaces for the direct deposition of end-group modified oligonucleotides by Dip-Pen Nanolithography. A study of the diffusion process was done in order to investigate the dependence of calibration coefficient and quality of deposited features on environmental parameters (temperature, relative humidity) and ink's molecular weight and functionality. The optimization of the process parameters led to the realization of high quality and density nanoarrays on plastics.

Lattice-matched double dip-shaped BAlGaN/AlN quantum well structures for ultraviolet light emission devices

Science.gov (United States)

Park, Seoung-Hwan; Ahn, Doyeol

2018-05-01

Ultraviolet light emission characteristics of lattice-matched BxAlyGa1-x-y N/AlN quantum well (QW) structures with double AlGaN delta layers were investigated theoretically. In contrast to conventional single dip-shaped QW structure where the reduction effect of the spatial separation between electron and hole wave functions is negligible, proposed double dip-shaped QW shows significant enhancement of the ultraviolet light emission intensity from a BAlGaN/AlN QW structure due to the reduced spatial separation between electron and hole wave functions. The emission peak of the double dip-shaped QW structure is expected to be about three times larger than that of the conventional rectangular AlGaN/AlN QW structure.

Second dip as a signature of ultrahigh energy proton interactions with cosmic microwave background radiation.

Science.gov (United States)

Berezinsky, V; Gazizov, A; Kachelrieb, M

2006-12-08

We discuss as a new signature for the interaction of extragalactic ultrahigh energy protons with cosmic microwave background radiation a spectral feature located at E= 6.3 x 10(19) eV in the form of a narrow and shallow dip. It is produced by the interference of e+e(-)-pair and pion production. We show that this dip and, in particular, its position are almost model-independent. Its observation by future ultrahigh energy cosmic ray detectors may give the conclusive confirmation that an observed steepening of the spectrum is caused by the Greisen-Zatsepin-Kuzmin effect.

Liquid-metal dip seal with pneumatic spring

International Nuclear Information System (INIS)

Poindexter, A.M.

1977-01-01

An improved liquid-metal dip seal for sealing the annulus between rotating plugs in the reactor vessel head of a liquid-metal fast-breeder nuclear reactor has two legs of differing widths communicating under a seal blade; the wide leg is also in communication with cover gas of the reactor and the narrow leg is also in communication with an isolated plug annulus above the seal. The annulus contains inert gas which acts as a pneumatic spring. Upon increasing cover gas pressure which depresses the level in the wide leg and greatly increases the level in the narrow leg, the pneumatic spring is compressed, and resists further level changes, thus preventing radioactive cover gas from bubbling through the seal

HOT 2014

DEFF Research Database (Denmark)

Lund, Henriette

Undersøgelse af, hvad der er hot - og hvad der burde være hot på læseområdet med 21 læsekyndige. Undersøgelsen er gennemført siden 2010. HOT-undersøgelsen er foretaget af Nationalt Videncenter for Læsning - Professionshøjskolerne i samarb. med Dansklærerforeningen...

Highly stretchable and conductive fibers enabled by liquid metal dip-coating

Science.gov (United States)

Zhang, Qiang; Roach, Devin J.; Geng, Luchao; Chen, Haosen; Qi, H. Jerry; Fang, Daining

2018-03-01

Highly stretchable and conductive fibers have been fabricated by dip-coating of a layer of liquid metal (eutectic gallium indium, EGaIn) on printed silicone elastomer filaments. This fabrication method exploits a nanolayer of oxide skin that rapidly forms on the surface of EGaIn when exposed to air. Through dip-coating, the sticky nature of the oxide skin leads to the formation of a thin EGaIn coating (˜5 μm thick) on the originally nonconductive filaments and renders these fibers excellent conductivity. Electrical characterization shows that the fiber resistance increases moderately as the fiber elongates but always maintains conductivity even when stretched by 800%. Besides this, these fibers possess good cyclic electrical stability with little degradation after hundreds of stretching cycles, which makes them an excellent candidate for stretchable conductors. We then demonstrate a highly stretchable LED circuit as well as a conductive stretchable net that extends the 1D fibers into a 2D configuration. These examples demonstrate potential applications for topologically complex stretchable electronics.

Hydraulic Properties of Closely Spaced Dipping Open Fractures Intersecting a Fluid-Filled Borehole Derived From Tube Wave Generation and Scattering

Science.gov (United States)

Minato, Shohei; Ghose, Ranajit; Tsuji, Takeshi; Ikeda, Michiharu; Onishi, Kozo

2017-10-01

Fluid-filled fractures and fissures often determine the pathways and volume of fluid movement. They are critically important in crustal seismology and in the exploration of geothermal and hydrocarbon reservoirs. We introduce a model for tube wave scattering and generation at dipping, parallel-wall fractures intersecting a fluid-filled borehole. A new equation reveals the interaction of tube wavefield with multiple, closely spaced fractures, showing that the fracture dip significantly affects the tube waves. Numerical modeling demonstrates the possibility of imaging these fractures using a focusing analysis. The focused traces correspond well with the known fracture density, aperture, and dip angles. Testing the method on a VSP data set obtained at a fault-damaged zone in the Median Tectonic Line, Japan, presents evidences of tube waves being generated and scattered at open fractures and thin cataclasite layers. This finding leads to a new possibility for imaging, characterizing, and monitoring in situ hydraulic properties of dipping fractures using the tube wavefield.

Updating the orbital ephemeris of the dipping source XB 1254-690 and the distance to the source

Science.gov (United States)

Gambino, Angelo F.; Iaria, Rosario; Di Salvo, Tiziana; Matranga, Marco; Burderi, Luciano; Pintore, Fabio; Riggio, Alessandro; Sanna, Andrea

2017-09-01

XB 1254-690 is a dipping low mass X-ray binary system hosting a neutron star and showing type I X-ray bursts. We aim at obtaining a more accurate orbital ephemeris and at constraining the orbital period derivative of the system for the first time. In addition, we want to better constrain the distance to the source in order to locate the system in a well defined evolutive scenario. We apply, for the first time, an orbital timing technique to XB 1254-690, using the arrival times of the dips present in the light curves that have been collected during 26 yr of X-ray pointed observations acquired from different space missions. We estimate the dip arrival times using a statistical method that weights the count-rate inside the dip with respect to the level of persistent emission outside the dip. We fit the obtained delays as a function of the orbital cycles both with a linear and a quadratic function. We infer the orbital ephemeris of XB 1254-690, improving the accuracy of the orbital period with respect to previous estimates. We infer a mass of M 2 = 0.42 ± 0.04 M ʘ for the donor star, in agreement with estimations already present in literature, assuming that the star is in thermal equilibrium while it transfers part of its mass via the inner Lagrangian point, and assuming a neutron star mass of 1.4 M ʘ. Using these assumptions, we also constrain the distance to the source, finding a value of 7.6 ± 0.8 kpc. Finally, we discuss the evolution of the system, suggesting that it is compatible with a conservative mass transfer driven by magnetic braking.

HOT 2010

DEFF Research Database (Denmark)

Lund, Henriette Romme

En undersøgelse af, hvad der er hot - og burde være hot på læseområdet. I undersøgelsen deltager en række læsekyndige fra praksisfeltet, professionshøjskolerne og forskningsområdet. Undersøgelsen er gentaget hvert år siden 2010.......En undersøgelse af, hvad der er hot - og burde være hot på læseområdet. I undersøgelsen deltager en række læsekyndige fra praksisfeltet, professionshøjskolerne og forskningsområdet. Undersøgelsen er gentaget hvert år siden 2010....

HOT 2013

DEFF Research Database (Denmark)

Lund, Henriette Romme

En undersøgelse af, hvad der er hot - og burde være hot på læseområdet. I undersøgelsen deltager en række læsekyndige fra praksisfeltet, professionshøjskolerne og forskningsområdet. Undersøgelsen er gentaget hvert år siden 2010.......En undersøgelse af, hvad der er hot - og burde være hot på læseområdet. I undersøgelsen deltager en række læsekyndige fra praksisfeltet, professionshøjskolerne og forskningsområdet. Undersøgelsen er gentaget hvert år siden 2010....

Suppression of sawtooth oscillations due to hot electrons and hot ions

International Nuclear Information System (INIS)

Zhang, Y.Z.; Berk, H.L.

1989-01-01

The theory of m = 1 kink mode stabilization is discussed in the presence of either magnetically trapped hot electrons or hot ions. For instability hot ion requires particles peaked inside the q = 1 surface, while hot electrons require that its pressure profile be increasing at the q = 1 surface. Experimentally observed sawtooth stabilization usually occurs with off-axis heating with ECRH and near axis heating with ICRH. Such heating may produce the magnetically trapped hot particle pressure profiles that are consistent with theory. 17 refs., 2 figs

The preparation and characterization of Bi-2212 film on Ag substrate by dip-coating method

International Nuclear Information System (INIS)

Song Yang; Zhao Liang; Li Pei; Qu Timing; Huang Yong; Han Zhenghe

2006-01-01

In this paper we report on the processing parameters and resulting critical current densities of Bi 2 Sr 2 Ca 1 Cu 2 O x thick films on Ag substrate. Bi-2212 tapes and wires are prepared by dip-coating method. It is found that parameters during partial melting (maximum process temperature T max and solidification temperature T s ) have strong influences on the transition temperature T c . The 0.5 mm diameter dip-coated wire can carry 4000 A/cm 2 critical current in 77 K, self field. Post-annealing on different temperatures and atmospheres are studied as well to obtain varied T c samples

Filmes de titânio-silício preparados por "spin" e "dip-coating"

Directory of Open Access Journals (Sweden)

Nassar Eduardo J.

2003-01-01

Full Text Available The conditions for the preparation of luminescent materials, consisting of Eu3+ ions entrapped in a titanium matrix, in the forma of a thin film, using the sol-gel process, are described. The films were obtained from sols prepared with TEOS and TEOT, in the presence of acetylacetone as the hidrolysis-retarding agent, using the dip-coating and spin-coating techniques. The influence of these techniques on the films based on titanium and silicon are presented. The Eu3+ was used as a luminescent probe. The films have been characterized by luminescence, reflection and transmittance. The thickness of the films could be related to the preparation procedure. Transparent thin films have been prepared by dip-coating technique.

Evaporation-Driven Deposition of ITO Thin Films from Aqueous Solutions with Low-Speed Dip-Coating Technique.

Science.gov (United States)

Ito, Takashi; Uchiyama, Hiroaki; Kozuka, Hiromitsu

2017-05-30

We suggest a novel wet coating process for preparing indium tin oxide (ITO) films from simple solutions containing only metal salts and water via evaporation-driven film deposition during low-speed dip coating. Homogeneous ITO precursor films were deposited on silica glass substrates from the aqueous solutions containing In(NO 3 ) 3 ·3H 2 O and SnCl 4 ·5H 2 O by dip coating at substrate withdrawal speeds of 0.20-0.50 cm min -1 and then crystallized by the heat treatment at 500-800 °C for 10-60 min under N 2 gas flow of 0.5 L min -1 . The ITO films heated at 600 °C for 30 min had a high optical transparency in the visible range and a good electrical conductivity. Multiple-coating ITO films obtained with five-times dip coating exhibited the lowest sheet (ρ S ) and volume (ρ V ) resistivities of 188 Ω sq -1 and 4.23 × 10 -3 Ω cm, respectively.

Impact of the Converter Control Strategies on the Drive Train of Wind Turbine during Voltage Dips

Directory of Open Access Journals (Sweden)

Fenglin Miao

2015-10-01

Full Text Available The impact of converter control strategies on the drive train of wind turbines during voltage dips is investigated in this paper using a full electromechanical model. Aerodynamics and tower vibration are taken into consideration by means of a simulation program, named FAST. Detailed gearbox and electrical subsystems are represented in MATLAB. The dynamic response of electromagnetic torque and its impact on the mechanical variables are the concern in this paper and the response of electrical variables is less discussed. From the mechanical aspects, the effect of rising power recovery speed and unsymmetrical voltage dips are analyzed on the basis of the dynamic response of the high-speed shaft (HSS. A comparison of the impact on the drive train is made for two converter control strategies during small voltage dips. Through the analysis of torque, speed and tower vibration, the results indicate that both power recovery speed and the sudden torque sag have a significant impact on drive trains, and the effects depend on the different control strategies. Moreover, resonance might be excited on the drive train by an unbalanced voltage.

On the absence of multiple dips in diffraction of high energy hadrons

International Nuclear Information System (INIS)

Malecki; Michalec, M.; Pallotta, M.

1997-07-01

An unorthodox insight into the structure of the geometrical Chou-Yang model explains the experimentally observed paradox of elastic diffraction of high energy hadrons without multiple dips. It is pointed out that the shadow scattering, away from the forward peak, is governed by small values of the coupling strength

Relationship between Microstructure and Ductility Dip Cracking resistance of Alloy 600/690 weld metals

Energy Technology Data Exchange (ETDEWEB)

Ryu, Jae Yong; Lee, Chang Hee [Hanyang University, Seoul (Korea, Republic of); Kim, Min Chul; Lee, Ho Jin; Kim, Keoung Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Kwang Soo; Shim, Deog Nam [Doosan HEAVY Industries and Construction, Seoul (Korea, Republic of)

2009-10-15

Ni-Cr-Fe alloys are used extensively in nuclear power systems for their resistance to general corrosion, localized corrosion, and environmentally assisted cracking. However, concerns with stress corrosion cracking of moderate chromium (14.22 wt-%) alloys such as Alloy 600 and its filler metals(FMs) (E-182 and EN82) have driven the application of higher chromium (28.30 wt-%) alloys like Alloy 690. While Alloy 690 and its FMs show outstanding resistance to environmentally assisted cracking in most water-reactor environments, these alloys are prone to welding defects, most notably to ductility dip cracking(DDC). The DDC occurs at temperatures between 0.5 and 0.8 of their melting temperature. This ductility drop may result in intergranular elevated temperature cracking often referred to as DDC. The DDC may occur during the high temperature processing of these alloys or during welding if the imposed strain exhausts the available ductility within this temperature range. Several alloy systems including Ni-base alloys, Ni.Cu alloys, Cu alloys, stainless steels and steels, have been reported to be susceptible to DDC. A complete understanding of the DDC mechanism does not exist, which makes DDC control in actual production conditions a very difficult task. In this study, the DDC resistance was evaluated with different FMs which have different chemical composition. The microstructural features of FMs such as precipitation behavior and grain boundaries morphology were observed, and it were correlated with the DDC susceptibility. The hot ductility test and strainto- fracture test was used to evaluate the DDC susceptibility at high temperature.

Relationship between Microstructure and Ductility Dip Cracking resistance of Alloy 600/690 weld metals

International Nuclear Information System (INIS)

Ryu, Jae Yong; Lee, Chang Hee; Kim, Min Chul; Lee, Ho Jin; Kim, Keoung Ho; Park, Kwang Soo; Shim, Deog Nam

2009-01-01

Ni-Cr-Fe alloys are used extensively in nuclear power systems for their resistance to general corrosion, localized corrosion, and environmentally assisted cracking. However, concerns with stress corrosion cracking of moderate chromium (14.22 wt-%) alloys such as Alloy 600 and its filler metals(FMs) (E-182 and EN82) have driven the application of higher chromium (28.30 wt-%) alloys like Alloy 690. While Alloy 690 and its FMs show outstanding resistance to environmentally assisted cracking in most water-reactor environments, these alloys are prone to welding defects, most notably to ductility dip cracking(DDC). The DDC occurs at temperatures between 0.5 and 0.8 of their melting temperature. This ductility drop may result in intergranular elevated temperature cracking often referred to as DDC. The DDC may occur during the high temperature processing of these alloys or during welding if the imposed strain exhausts the available ductility within this temperature range. Several alloy systems including Ni-base alloys, Ni.Cu alloys, Cu alloys, stainless steels and steels, have been reported to be susceptible to DDC. A complete understanding of the DDC mechanism does not exist, which makes DDC control in actual production conditions a very difficult task. In this study, the DDC resistance was evaluated with different FMs which have different chemical composition. The microstructural features of FMs such as precipitation behavior and grain boundaries morphology were observed, and it were correlated with the DDC susceptibility. The hot ductility test and strainto- fracture test was used to evaluate the DDC susceptibility at high temperature

HOT STARS WITH HOT JUPITERS HAVE HIGH OBLIQUITIES

International Nuclear Information System (INIS)

Winn, Joshua N.; Albrecht, Simon; Fabrycky, Daniel; Johnson, John Asher

2010-01-01

We show that stars with transiting planets for which the stellar obliquity is large are preferentially hot (T eff > 6250 K). This could explain why small obliquities were observed in the earliest measurements, which focused on relatively cool stars drawn from Doppler surveys, as opposed to hotter stars that emerged more recently from transit surveys. The observed trend could be due to differences in planet formation and migration around stars of varying mass. Alternatively, we speculate that hot-Jupiter systems begin with a wide range of obliquities, but the photospheres of cool stars realign with the orbits due to tidal dissipation in their convective zones, while hot stars cannot realign because of their thinner convective zones. This in turn would suggest that hot Jupiters originate from few-body gravitational dynamics and that disk migration plays at most a supporting role.

Canine renal cortical necrosis and haemorrhage following ingestion of an Amitraz-formulated insecticide dip : clinical communication

Directory of Open Access Journals (Sweden)

P.A. Oglesby

2006-06-01

Full Text Available Amitraz is a formamidine compound used in veterinary medicine as a topical dip to control ticks and mites on dogs and livestock. A 10-year-old female Scottish terrier was presented following the accidental oral administration of a dip containing amitraz. This case report describes the clinical signs, treatment and pathology of this dog. Clinical signs of toxicity from amitraz result from stimulation of alpha2-adrenergic receptors. Amitraz is seldom fatal because the effects can be reversed by alpha2-adrenergic antagonists. The dog recovered from the amitraz toxicity but died 5 days later from acute renal failure.

Homogeneous PCBM layers fabricated by horizontal-dip coating for efficient bilayer heterojunction organic photovoltaic cells.

Science.gov (United States)

Huh, Yoon Ho; Bae, In-Gon; Jeon, Hong Goo; Park, Byoungchoo

2016-10-31

We herein report a homogeneous [6,6]-phenyl C61 butyric acid methyl ester (PCBM) layer, produced by a solution process of horizontal-dipping (H-dipping) to improve the photovoltaic (PV) effects of bilayer heterojunction organic photovoltaic cells (OPVs) based on a bi-stacked poly(3-hexylthiophene) (P3HT) electron donor layer and a PCBM electron acceptor layer (P3HT/PCBM). It was shown that a homogeneous and uniform coating of PCBM layers in the P3HT/PCBM bilayer OPVs resulted in reliable and reproducible device performance. We recorded a power conversion efficiency (PCE) of 2.89%, which is higher than that (2.00%) of bilayer OPVs with a spin-coated PCBM layer. Moreover, introducing surfactant additives of poly(oxyethylene tridecyl ether) (PTE) into the homogeneous P3HT/PCBM PV layers resulted in the bilayer OPVs showing a PCE value of 3.95%, which is comparable to those of conventional bulk-heterojunction (BHJ) OPVs (3.57-4.13%) fabricated by conventional spin-coating. This improved device performance may be attributed to the selective collection of charge carriers at the interfaces among the active layers and electrodes due to the PTE additives as well as the homogeneous formation of the functional PCBM layer on the P3HT layer. Furthermore, H-dip-coated PCBM layers were deposited onto aligned P3HT layers by a rubbing technique, and the rubbed bilayer OPV exhibited improved in-plane anisotropic PV effects with PCE anisotropy as high as 1.81, which is also higher than that (1.54) of conventional rubbed BHJ OPVs. Our results suggest that the use of the H-dip-coating process in the fabrication of PCBM layers with the PTE interface-engineering additive could be of considerable interest to those seeking to improve PCBM-based opto-electrical organic thin-film devices.

Active and reactive power control schemes for distributed generation systems under voltage dips

NARCIS (Netherlands)

Wang, F.; Duarte, J.L.; Hendrix, M.A.M.

2009-01-01

During voltage dips continuous power delivery from distributed generation systems to the grid is desirable for the purpose of grid support. In order to facilitate the control of distributed generation systems adapted to the expected change of grid requirements, generalized power control schemes

Multi-photon resonant effects in strong-field ionization: origin of the dip in experimental longitudinal momentum distributions

International Nuclear Information System (INIS)

Alnaser, A S; Maharjan, C M; Wang, P; Litvinyuk, I V

2006-01-01

We studied ionization of neon and argon by intense linearly polarized femtosecond laser pulses of different wavelengths (400 nm and 800 nm) and peak intensities, and by measuring momentum distributions of singly charged positive ions in the direction parallel to laser polarization. For Ne the momentum distributions exhibited a characteristic dip at zero momentum at 800 nm and a complex multipeak structure at 400 nm. Similarly, for Ar the momentum distributions evolved from a complex multipeak structure with a pronounced dip in the centre at 400 nm, to a smooth distribution characteristic of pure tunneling ionization (800 nm, high intensities). In the intermediate regime (800 nm, medium to low intensities), for both atoms we observed recoil ion momentum distributions modulated by quasi-periodic structures usually seen in the photoelectron energy spectra in a multi-photon regime (ATI spectra). Ne did show a characteristic 'dip' at low momentum, while the longitudinal momentum distribution for Ar exhibited a spike at zero momentum instead. The spectra did dramatically change at 400 nm, where both ions show the pronounced dip near zero momentum. Based on our results, we conclude that the structures observed in Ne and Ar momentum distributions reflect the specifics of atomic structure of the two targets and should not be attributed to effects of electron recollision, as was suggested earlier. Instead, as our results indicate, they are due to the effects of multi-photon resonant enhancement of strong-field ionization. (letter to the editor)

Growth and characterization of magnetite-maghemite thin films by the dip coating method

International Nuclear Information System (INIS)

Velásquez, A. A.; Arnedo, A.

2017-01-01

We present the process of growth and characterization of magnetite-maghemite thin films obtained by the dip coating method. The thin films were deposited on glass substrates, using a ferrofluid of nanostructured magnetite-maghemite particles as precursor solution. During the growth of the films the following parameters were controlled: number of dips of the substrates, dip velocity of the substrates and drying times. The films were characterized by Atomic Force Microscopy, Scanning Elelectron Microscopy, four-point method for resistance measurement, Room Temperature Mössbauer Spectroscopy and Hall effect. Mössbauer measurements showed the presence of a sextet attributed to maghemite (γ-Fe_2O_3) and two doublets attributed to superparamagnetic magnetite (Fe_3O_4), indicating a distribution of oxidation states of the iron as well as a particle size distribution of the magnetic phases in the films. Atomic force microscopy measurements showed that the films cover quasi uniformly the substrates, existing in them some pores with sub-micron size. Scanning Electron Microscopy measurements showed a uniform structure in the films, with spherical particles with size around 10 nm. Voltage versus current measurements showed an ohmic response of the films for currents between 0 and 100 nA. On the other hand, Hall effect measurements showed a nonlinear response of the Hall voltage with the magnetic flux density applied perpendicular to the plane of the films, however the response is fairly linear for magnetic flux densities between 0.15 and 0.35 T approximately. The results suggest that the films are promising for application as magnetic flux density sensors.

A Dip Structure in the Intrinsic Toroidal Rotation Near the Edge of the Ohmic Plasmas in EAST

DEFF Research Database (Denmark)

Xu, Guosheng; Naulin, Volker; Wan, Baonian

2011-01-01

and outwards. The radial width of the vt dip was 1 cm to 2 cm, and both the density and electron temperature profiles exhibited steep gradients at this dip position. It was observed in both divertor and limiter configurations. To find out its origin, the toroidal torques induced by neutral friction......, neoclassical viscosity, collisional perpendicular shear viscosity, ion orbit loss and turbulent Reynolds stress were estimated using the measured parameters. Our results indicate that in this particular parameter regime the neutral friction was the dominant damping force. The calculated cocurrent toroidal...

DIP (pneumonia intersticial descamativa: como quadro do pulmão do tabaco – apresentação de um caso

Directory of Open Access Journals (Sweden)

Vítor Sousa

2004-09-01

Full Text Available RESUMO: A DIP (pneumonia intersticial descamativa é uma doença pulmonar intersticial caracterizada pela acumulação difusa e uniforme de macrófagos alveolares. Há forte associação com o tabaco sendo que 90% dos doentes são fumadores. As doenças relacionadas com o tabaco no pulmão são diversas e incluem os tumores, enfisema, bronquite crónica, RBILD (bronquiolite respiratória associada a doença pulmonar intersticial, DIP e histiocitose de células de Langerhans. Os autores apresentam um caso de DIP. É realizada breve revisão teórica e discussão do caso à luz da sua associação com o tabaco.REV PORT PNEUMOL 2004; X (5: 431-435 ABSTRACT: DIP (Desquamative Interstitial Pneumonia is an interstitial lung disease with diffuse and uniform accumulation of alveolar macrophages. There is a strong association with tobacco since 90% of the patients are smokers. The interstitial lung diseases related to tobacco are diverse and include tumours, emphysema, chronic bronchitis, RBILD (Respiratory Bronchilites associated Interstitial Lung Disease, DIP and Langerhans Cell Histiocitosis. The authors present a case of DIP. A brief theorycal revision and discussion of a case is made facing the association with tobacco.REV PORT PNEUMOL 2004; X (5:431-435 Palavras-chave: Pulmão, pneumonia intersticial descamativa, DIP, interstício, Key-words: Lung, desquamative interstitial pneumonia, DIP, interstitium

DipA, a pore-forming protein in the outer membrane of Lyme disease spirochetes exhibits specificity for the permeation of dicarboxylates.

Directory of Open Access Journals (Sweden)

Marcus Thein

Full Text Available Lyme disease Borreliae are highly dependent on the uptake of nutrients provided by their hosts. Our study describes the identification of a 36 kDa protein that functions as putative dicarboxylate-specific porin in the outer membrane of Lyme disease Borrelia. The protein was purified by hydroxyapatite chromatography from Borrelia burgdorferi B31 and designated as DipA, for dicarboxylate-specific porin A. DipA was partially sequenced, and corresponding genes were identified in the genomes of B. burgdorferi B31, Borrelia garinii PBi and Borrelia afzelii PKo. DipA exhibits high homology to the Oms38 porins of relapsing fever Borreliae. B. burgdorferi DipA was characterized using the black lipid bilayer assay. The protein has a single-channel conductance of 50 pS in 1 M KCl, is slightly selective for anions with a permeability ratio for cations over anions of 0.57 in KCl and is not voltage-dependent. The channel could be partly blocked by different di- and tricarboxylic anions. Particular high stability constants up to about 28,000 l/mol (in 0.1 M KCl were obtained among the 11 tested anions for oxaloacetate, 2-oxoglutarate and citrate. The results imply that DipA forms a porin specific for dicarboxylates which may play an important role for the uptake of specific nutrients in different Borrelia species.

The Interplay between Gaze Following, Emotion Recognition, and Empathy across Adolescence; a Pubertal Dip in Performance?

Directory of Open Access Journals (Sweden)

Rianne van Rooijen

2018-02-01

Full Text Available During puberty a dip in face recognition is often observed, possibly caused by heightened levels of gonadal hormones which in turn affects the re-organization of relevant cortical circuitry. In the current study we investigated whether a pubertal dip could be observed in three other abilities related to social information processing: gaze following, emotion recognition from the eyes, and empathizing abilities. Across these abilities we further explored whether these measurements revealed sex differences as another way to understand how gonadal hormones affect processing of social information. Results show that across adolescence, there are improvements in emotion recognition from the eyes and in empathizing abilities. These improvements did not show a dip, but are more plateau-like. The gaze cueing effect did not change over adolescence. We only observed sex differences in empathizing abilities, with girls showing higher scores than boys. Based on these results it appears that gonadal hormones are not exerting a unified influence on higher levels of social information processing. Further research should also explore changes in (visual information processing around puberty onset to find a more fitted explanation for changes in social behavior across adolescence.

Production and installation of equipments for radiation-induced graft polymerization in liquid phase and dipping techniques

International Nuclear Information System (INIS)

Seko, Noriaki; Kasai, Noboru; Tamada, Masao; Hasegawa, Shin; Katakai, Akio; Sugo, Takanobu

2005-01-01

Fibrous adsorbent which is synthesized by radiation induced graft polymerization on the trunk polymers such as polymer nonwoven fabrics and woven cloths exhibits an excellent selective adsorption against heavy metal ions and toxic gases at extremely low concentrations. Two equipments were installed to synthesize the metal-ion and gas adsorbents by means of the radiation-induced graft polymerization in the liquid phase and the dipping, respectively. In the reation chamber of the liquid phase reactor, the oxygen decreased to 100 ppm. The inside temperature was elevated at 80C. These characteristics satisfied the specification. The fabric transport can regulate the rate in the range from 1 to 10 m/min. The reactor for the dip grafting could reduce the inside oxygen to 100ppm and inside temperature could reach to 80C, also. The transport system is stable during the dip grafting reaction. The grafting of glycidyl methacrylate was carried out as a characteristic test. The degree of grafting was controlled in the range of 40-70%. The both equipments can graft the trunk polymer, 2000mm in maximum width and 1m in maximum diameter. This size is enough for confirmation practical scale synthesis. (author)

Polyimide Dielectric Layer on Filaments for Organic Field Effect Transistors: Choice of Solvent, Solution Composition and Dip-Coating Speed

Directory of Open Access Journals (Sweden)

Rambausek Lina

2014-09-01

Full Text Available In today’s research, smart textiles is an established topic in both electronics and the textile fields. The concept of producing microelectronics directly on a textile substrate is not a mere idea anymore and several research institutes are working on its realisation. Microelectronics like organic field effect transistor (OFET can be manufactured with a layered architecture. The production techniques used for this purpose can also be applied on textile substrates. Besides gate, active and contact layers, the isolating or dielectric layer is of high importance in the OFET architecture. Therefore, generating a high quality dielectric layer that is of low roughness and insulating at the same time is one of the fundamental requirements in building microelectronics on textile surfaces. To evaluate its potential, we have studied polyimide as a dielectric layer, dip-coated onto copper-coated polyester filaments. Accordingly, the copper-coated polyester filament was dip-coated from a polyimide solution with two different solvents, 1-methyl-2-pyrrolidone (NMP and dimethylformaldehyde. A variety of dip-coating speeds, solution concentrations and solvent-solute combinations have been tested. Their effect on the quality of the layer was analysed through microscopy, leak current measurements and atomic force microscopy (AFM. Polyimide dip-coating with polyimide resin dissolved in NMP at a concentration of 15w% in combination with a dip-coating speed of 50 mm/min led to the best results in electrical insulation and roughness. By optimising the dielectric layer’s properties, the way is paved for applying the subsequent semi-conductive layer. In further research, we will be working with the organic semiconductor material TIPS-Pentacene

Effect of Dipping and Vacuum Impregnation Coating Techniques with Alginate Based Coating on Physical Quality Parameters of Cantaloupe Melon.

Science.gov (United States)

Senturk Parreidt, Tugce; Schmid, Markus; Müller, Kajetan

2018-04-01

Edible coating based on sodium alginate solution was applied to fresh-cut cantaloupe melon by dipping and vacuum impregnation coating methods. One aim of this work is to produce more technical information concerning these conventional and novel coating processes. For this purpose, the effect of various coating parameters (dipping time, draining time, time length of the vacuum period, vacuum pressure, atmospheric restoration time) with several levels on physical quality parameters (percentage of weight gain, color, and texture) of noncoated and coated samples were determined in order to define adequate coating process parameters to achieve a successful coating application. Additionally, the effects of dipping and vacuum impregnation processes were compared. Both processes improved the firmness of the melon pieces. However, vacuum impregnation application had higher firmness and weight gain results, and had significant effect (P coating technique and the parameters used significantly affect the physical quality characteristics of coated food products. The work presented produced more technical information concerning dipping and vacuum impregnation coating techniques, along with evaluating the effects of various coating parameters with several levels. The results revealed that vacuum impregnation technique is a successful coating method; however the effects should be carefully assessed for each product. © 2018 Institute of Food Technologists®.

Proposal for defining voltage dip-related responsibility sharing at a point of connection

NARCIS (Netherlands)

Bhattacharyya, S.; Cobben, J.F.G.; Kling, W.L.

2012-01-01

Modern customers use many electronics devices that are quite sensitive to the quality of power supply. Voltage dip is an important power quality (PQ) issue that can cause damage to various customers' devices and might lead to partial or complete interruption of the operation of an installation.

Random Walk Model for the Growth of Monolayer in Dip Pen Nanolithography

International Nuclear Information System (INIS)

Kim, H; Ha, S; Jang, J

2013-01-01

By using a simple random-walk model, we simulate the growth of a self-assembled monolayer (SAM) pattern generated in dip pen nanolithography (DPN). In this model, the SAM pattern grows mainly via the serial pushing of molecules deposited from the tip. We examine various SAM patterns, such as lines, crosses, and letters by changing the tip scan speed.

Conformal dip-coating of patterned surfaces for capillary die-to-substrate self-assembly

International Nuclear Information System (INIS)

Mastrangeli, M; Ruythooren, W; Van Hoof, C; Celis, J-P

2009-01-01

Capillarity-driven self-assembly of small chips onto planar target substrates is a promising alternative to robotic pick-and-place assembly. It critically relies on the selective deposition of thin fluid films on patterned binding sites, which is anyway normally non-conformal. We found that the addition of a thin wetting sidewall, surrounding the entire site perimeter, enables the conformal fluid coverage of arbitrarily shaped sites through dip-coating, significantly improves the reproducibility of the coating process and strongly reduces its sensitivity to surface defects. In this paper we support the feasibility and potential of this method by demonstrating the conformal dip-coating of square and triangular sites conditioned with combinations of different hydrophobic and hydrophilic surface chemistries. We present both experimental and simulative evidence of the advantages brought by the introduction of the wetting boundary on film coverage accuracy. Application of our surface preparation method to capillary self-assembly could result in higher precision in die-to-substrate registration and larger freedom in site shape design

Use of 2-hydroxylhydrazine as a new modifier in dip-coating nickel films

International Nuclear Information System (INIS)

Syukri, R.; Ito, Yusuke; Ban, Takayuki; Ohya, Yutaka; Takahashi, Yasutaka

2002-01-01

A modified version of the dip-coating technique, which uses 2-hydroxylhydrazine as a mild reducing agent, was applied in the fabrication of nickel thin films. Nickel acetate was used as metal source. Metallic nickel thin films were formed on glass substrates by firing in the range of 400-600 deg. C under nitrogen atmosphere. The deposited layers were composed of cubic Ni crystallites. X-ray photoelectron spectroscopy analysis indicated almost uniformity in composition throughout the film thickness. The morphology of the films analyzed by scanning electron microscopy and atomic force microscopy revealed a very weak roughness after firing at 400 deg. C and the films turned out to be homogeneous. A thin film of approximately 19 nm in thickness exhibited a high resistivity of 86 μΩ cm. However, the resistivity was found to gradually decrease with increasing film thickness up to 110 nm by repeated dip-coating, reaching a minimum value of approximately 10 μΩ cm

Solid-state ZnS quantum dot-sensitized solar cell fabricated by the Dip-SILAR technique

International Nuclear Information System (INIS)

Mehrabian, M; Mirabbaszadeh, K; Afarideh, H

2014-01-01

Solid-state quantum dot sensitized solar cells (QDSSCs) were fabricated with zinc sulfide quantum dots (ZnS QDs), which served as the light absorber and the recombination blocking layer simultaneously. ZnS QDs were prepared successfully by a novel successive ionic layer adsorption and reaction technique based on dip-coating (Dip-SILAR). The dependences of the photovoltaic parameters on the number of SILAR cycles (n) were investigated. The cell with n = 6 (particle average size ∼9 nm) showed an energy conversion efficiency of 2.72% under the illumination of one sun (AM 1.5, 100 mW cm −2 ). Here we investigate also the cohesion between ZnS QDs and ZnO film to obtain a well-covering QD layer. (paper)

Pengaruh teat dipping menggunakan dekok daun kersen (Muntingia calabura L. terhadap tingkat kejadian mastitis

Directory of Open Access Journals (Sweden)

Indra Kurniawan

2014-02-01

Full Text Available ABSTRACT: The study was carried out in Sidomulyo Village, Jabung, Malang Regen-cy from April 6th to May 6th, 2013. The objective of the study was to evaluate the influ-ence of Kersen leaf (Muntingia calabura L extract to reduce mastitis incidents. The materials used in this study were 15 Friesian Holstein crossbreed lactating dairy cows, chemical antiseptic, and Kersen leaf extract. The study used experiment Randomized Block Design with 3 treatments and 5 replications. The result shows that Kersen leaf extract was significantly (p>0.05 able to reduce mastitis incidents particularly 20% of Kersen leaf extract composition. The study suggests that Kersen leaf extract can be used as an effective substance in dipping solution for dairy cows Mastitis control program. Keywords: Kersen leaf extract, mastitis, teat dipping, dairy cows

Growth and characterization of magnetite-maghemite thin films by the dip coating method

Energy Technology Data Exchange (ETDEWEB)

Velásquez, A. A., E-mail: avelas26@eafit.edu.edu.co; Arnedo, A. [Universidad EAFIT, Grupo de Electromagnetismo Aplicado (Colombia)

2017-11-15

We present the process of growth and characterization of magnetite-maghemite thin films obtained by the dip coating method. The thin films were deposited on glass substrates, using a ferrofluid of nanostructured magnetite-maghemite particles as precursor solution. During the growth of the films the following parameters were controlled: number of dips of the substrates, dip velocity of the substrates and drying times. The films were characterized by Atomic Force Microscopy, Scanning Elelectron Microscopy, four-point method for resistance measurement, Room Temperature Mössbauer Spectroscopy and Hall effect. Mössbauer measurements showed the presence of a sextet attributed to maghemite (γ-Fe{sub 2}O{sub 3}) and two doublets attributed to superparamagnetic magnetite (Fe{sub 3}O{sub 4}), indicating a distribution of oxidation states of the iron as well as a particle size distribution of the magnetic phases in the films. Atomic force microscopy measurements showed that the films cover quasi uniformly the substrates, existing in them some pores with sub-micron size. Scanning Electron Microscopy measurements showed a uniform structure in the films, with spherical particles with size around 10 nm. Voltage versus current measurements showed an ohmic response of the films for currents between 0 and 100 nA. On the other hand, Hall effect measurements showed a nonlinear response of the Hall voltage with the magnetic flux density applied perpendicular to the plane of the films, however the response is fairly linear for magnetic flux densities between 0.15 and 0.35 T approximately. The results suggest that the films are promising for application as magnetic flux density sensors.

T-DNA transfer and T-DNA integration efficiencies upon Arabidopsis thaliana root explant cocultivation and floral dip transformation.

Science.gov (United States)

Ghedira, Rim; De Buck, Sylvie; Van Ex, Frédéric; Angenon, Geert; Depicker, Ann

2013-12-01

T-DNA transfer and integration frequencies during Agrobacterium-mediated root explant cocultivation and floral dip transformations of Arabidopsis thaliana were analyzed with and without selection for transformation-competent cells. Based on the presence or absence of CRE recombinase activity without or with the CRE T-DNA being integrated, transient expression versus stable transformation was differentiated. During root explant cocultivation, continuous light enhanced the number of plant cells competent for interaction with Agrobacterium and thus the number of transient gene expression events. However, in transformation competent plant cells, continuous light did not further enhance cotransfer or cointegration frequencies. Upon selection for root transformants expressing a first T-DNA, 43-69 % of these transformants showed cotransfer of another non-selected T-DNA in two different light regimes. However, integration of the non-selected cotransferred T-DNA occurred only in 19-46 % of these transformants, indicating that T-DNA integration in regenerating root cells limits the transformation frequencies. After floral dip transformation, transient T-DNA expression without integration could not be detected, while stable T-DNA transformation occurred in 0.5-1.3 % of the T1 seedlings. Upon selection for floral dip transformants with a first T-DNA, 8-34 % of the transformants showed cotransfer of the other non-selected T-DNA and in 93-100 % of them, the T-DNA was also integrated. Therefore, a productive interaction between the agrobacteria and the female gametophyte, rather than the T-DNA integration process, restricts the floral dip transformation frequencies.

Seaward dipping reflectors along the SW continental margin of India: Evidence for volcanic passive margin

Digital Repository Service at National Institute of Oceanography (India)

Ajay, K.K.; Chaubey, A.K.; Krishna, K.S.; Rao, D.G.; Sar, D.

Multi-channel seismic reflection profiles across the southwest continental margin of India (SWCMI) show presence of westerly dipping seismic reflectors beneath sedimentary strata along the western flank of the Laccadive Ridge-northernmost part...

Development of Continuous Galvanization-compatible Martensitic Steel

Energy Technology Data Exchange (ETDEWEB)

Gong, Y. F.; Song, T. J.; Kim, Han S.; De Cooman [Pohang Univ. of Science and Technology, Pohang (Korea, Republic of); Kwak, J. H. [POSCO Gwangyang Works, Gwangyang (Korea, Republic of)

2012-01-15

The development of martensitic grades which can be processed in continuous galvanizing lines requires the reduction of the oxides formed on the steel during the hot dip process. This reduction mechanism was investigated in detail by means of High Resolution Transmission Electron Microscopy (HR-TEM) of cross-sectional samples. Annealing of a martensitic steel in a 10% H{sub 2} + N{sub 2} atmosphere with the dew point of -35 .deg. C resulted in the formation of a thin c-xMno.SiO{sub 2} (x>1) oxide film and amorphous a-xMnO.SiO{sub 2} oxide particles on the surface. During the hot dip galvanizing in Zn-0.13%Al, the thin c-xMnO.SiO{sub 2} (x>1) oxide films was reduced by the Al. The a-xMnO.SiO{sub 2} (x<0.9) and a-SiO{sub 2} (x>1) oxide film was also reduced and the amorphous a-xMnO.SiO{sub 2} and a-SiO{sub 2} particles were embedded in the Fe{sub 2}Al{sub 5-x}Zn{sub x} inhibition layer formed at the steel/coating interface during hot dipping. The results clearly show that Al in the liquid Zn bath can reduce the crystalline c-xMn.SiO{sub 2} (x>1) oxides but not the amorphous a-xMnO.SiO{sub 2} (x<0.9) and a-SiO{sub 2} oxides. These oxides remain embedded in the Zn layer or in the inhibition layer, making it possible to apply a Zn or Zn-alloy coating on martensitic steel by hot dipping. The hot dipping process was also found to deteriorate the mechanical properties, independently of the Zn bath composition.

Recent photometric monitoring of KIC 8462852, the detection of a potential repeat of the Kepler day 1540 dip and a plausible model

Science.gov (United States)

Bourne, R.; Gary, B. L.; Plakhov, A.

2018-04-01

This paper presents V- and g΄-band observations of the F2V star KIC 8462852, which exhibited enigmatic fade patterns in Kepler mission data. We introduce a transit simulation model for interpretation of these fades, and use it to interpret a 2017 August dip as a repeat of the Kepler day 1540 dip (D1540). We suggest the 2017 August and D1540 dips may be caused by a brown dwarf and an associated ring system in a 1601-d elliptical orbit. Transiting icy moons of the proposed brown dwarf, sublimating near periapsis like comets, could provide an explanation for the significant dips observed by Kepler, as well as the recent 2017 May to October dips and the long-term variation in flux detected by Simon et al. Whereas the presence of such a ring structure is attractive for its ability to explain short-term fade events, we do not address how such a ring system can be created and maintained. This speculation predicted a brightening of ˜1 per cent that occurred during October 2017. In addition, this scenario predicts that a set of dimming events, similar to those in 2013 (Kepler) and in 2017 (reported here), can be expected to repeat during 2021 October to 2022 January and a repeat of D1540 should occur on 2021 December 27.

Static deformation due to a long buried dip-slip fault in an isotropic

Indian Academy of Sciences (India)

Closed-form analytical expressions for the displacements and the stresses at any point of a two-phase medium consisting of a homogeneous, isotropic, perfectly elastic half-space in welded contact with a homogeneous, orthotropic, perfectly elastic half-space due to a dip-slip fault of finite width located at an arbitrary ...

Morphology control in thin films of PS:PLA homopolymer blends by dip-coating deposition

Energy Technology Data Exchange (ETDEWEB)

Vital, Alexane [Interfaces, Confinement, Matériaux et Nanostructures (ICMN), CNRS-Université d’Orléans, UMR 7374, 1B Rue de la Férollerie, C.S. 40059, 45071 Orléans Cedex 2 (France); Groupe de recherches sur l’énergétique des milieux ionisés (GREMI), CNRS-Université d’Orléans, UMR 7344, 14 rue d' Issoudun, B.P. 6744, F45067 Orléans Cedex 2 (France); Vayer, Marylène [Interfaces, Confinement, Matériaux et Nanostructures (ICMN), CNRS-Université d’Orléans, UMR 7374, 1B Rue de la Férollerie, C.S. 40059, 45071 Orléans Cedex 2 (France); Tillocher, Thomas; Dussart, Rémi [Groupe de recherches sur l’énergétique des milieux ionisés (GREMI), CNRS-Université d’Orléans, UMR 7344, 14 rue d' Issoudun, B.P. 6744, F45067 Orléans Cedex 2 (France); Boufnichel, Mohamed [STMicroelectronics, 16, rue Pierre et Marie Curie, B.P. 7155, 37071 Tours Cedex 2 (France); and others

2017-01-30

Highlights: • A process to control the morphology of polymer blends thin film is described. • It is based on the use of dip-coating at various withdrawal speeds. • The process is examined within the capillary and the draining regimes. • The final dried morphology is controlled by the regime of deposition. • This study is of high interest for the preparation of advanced functional surfaces. - Abstract: In this work, smooth polymer films of PS, PLA and their blends, with thicknesses ranging from 20 nm up to 400 nm and very few defects on the surface were obtained by dip-coating. In contrast to the process of spin-coating which is conventionally used to prepare thin films of polymer blends, we showed that depending on the deposition parameters (withdrawal speed and geometry of the reservoir), various morphologies such as layered films and laterally phase-separated domains could be formed for a given blend/solvent pair, offering much more opportunities compared to the spin-coating process. This diversity of morphologies was explained by considering the superposition of different phenomena such as phase separation process, dewetting and vitrification in which parameters such as the drying time, the compatibility of the polymer/solvent pairs and the affinity of the polymer towards the interfaces were suspected to play a significant role. For that purpose, the process of dip-coating was examined within the capillary and the draining regimes (for low and high withdrawal speed respectively) in order to get a full description of the thickness variation and evaporation rate as a function of the deposition parameters.

Dip coating of sol-gels

Science.gov (United States)

Schunk, P. R.; Hurd, A. J.; Brinker, C. J.

Dip coating is the primary means of depositing sol-gel films for precision optical coatings. Sols are typically multicomponent systems consisting of an inorganic phase dispersed in a solvent mixture, with each component differing in volatility and surface tension. This, together with slow coating speeds (less than 1cm/s), makes analysis of the coating process complicated; unlike most high-speed coating methods, solvent evaporation, evolving rheology, and surface tension gradients alter significantly the fluid mechanics of the deposition stage. These phenomena were studied with computer-aided predictions of the flow and species transport fields. The underlying theory involves mass, momentum, and species transport on a domain of unknown shape, with models and constitutive equations for vapor-liquid equilibria and surface tension. Due accounting is made for the unknown position of the free surface, which locates according to the capillary hydrodynamic forces and solvent loss by evaporation. Predictions of the effects of mass transfer, hydrodynamics, and surface tension gradients on final film thickness are compared with ellipsometry measurements of film thickness on a laboratory pilot coater. Although quantitative agreement is still lacking, both experiment and theory reveal that the film profile near the drying line takes on a parabolic shape.

Nature of the high-binding-energy dip in the low-temperature photoemission spectra of Bi2Sr2CaCu2O8+δ

International Nuclear Information System (INIS)

Dessau, D.S.; Shen, Z.; Wells, B.O.; King, D.M.; Spicer, W.E.; Arko, A.J.; Lombardo, L.W.; Mitzi, D.B.; Kapitulnik, A.

1992-01-01

At the transition to superconductivity, an anomalous high-binding-energy (∼-90 meV) dip appears in the low-temperature photoemission spectra taken along the Γ-bar M high-symmetry direction of Bi 2 Sr 2 CaCu 2 O 8+δ . This paper details experiments which further characterize the energy and k-space dependence of this dip structure. The dip occurs over a wide portion of the Γ-bar M zone diagonal (110), yet shows minimal energy dispersion. In the spectra taken along the Γ-X zone edge (100), the dip is very weak or not present. We show that these results imply that the dip is not an artifact dependent on the experiment or special features of the band structure and therefore is an intrinsic feature of the superconducting state of Bi 2 Sr 2 CaCu 2 O 8+δ . The behavior of the normal-state bands along Γ-bar M in relation to the local-density-approximation prediction of a Bi-O-based electron ''pocket'' is also discussed, with our data explained most naturally if the Bi-O band remains above the Fermi level for all k

How to dip nectar: optimal time apportionment in natural viscous fluid transport

Science.gov (United States)

Wu, Jianing; Shi, Guanya; Zhao, Yiwei; Yan, Shaoze

2018-06-01

The mouthparts of some animals are highly evolved fluid transporters. Most honeybees dip viscous nectar in a cyclic fashion by using protrusible tongues with active hairs that can erect rhythmically. The glossal hairs flatten when the tongue extends into the nectar, and then erect outwards like an umbrella to catch nectar while retracting. This paper examines the potential capability of honeybees in allocating the duration of the tongue protraction and retraction phases for the sake of energy saving. A physical model is established to analyze energy consumption induced by viscous drag, considering tongue kinematics and variation of the surface profile in different phases of tongue movements. The results indicate that the theoretically optimal time apportionment ratio at which the energy consumption is the minimum, is directly related to the square root of the tongue’s diameter ratio between the protraction and retraction phase. Through dipping observations, we validate that the duration for the protraction and retraction phases show high accordance with the theoretical prediction. These findings not only broaden the insights into honeybee’s foraging strategy but inspire the design of high-performance microfluidic pumps with dynamic surfaces to transport viscous fluid.

Studies on the environmental chemistry and dissipation of 14C-labelled Deltamethrin and Amitraz in model dips

International Nuclear Information System (INIS)

Musumeci, M.R.; Coelho, P.V.; Luchini, L.C.

1997-01-01

The degradation of 14 C-labelled deltamethrin under variable conditions of pH and temperature, leaching of 14 C-labelled amitraz in soil columns and dissipation of these insecticides in model dipping vat was studied. Deltamethrin was stable for 28 d in buffer solutions at pH 4,7 and 8 and at temperature of 14, 28 and 35 deg. C, but degraded in a solution at pH 9. Metabolites identified by TLC corresponded to 3-phenoxybenzoic acid and 3-phenoxybenzyl alcohol. After 75 days of standing in a model dip, about 60% of the total radioactivity was found in the sediment and corresponded mainly to deltamethrin. When 14 C-Amitraz was applied to soil columns, placed under outdoor conditions, 4 months later all of the radiocarbon was found in the upper 10 cm section and about 90% of the recovered radioactivity corresponded with amitraz. A study of the dissipation of amitraz in a field vat showed that after 20 d of use the concentration of amitraz in a field dip decreased from 210 μg/mL to 155 μg/mL. (author)

Westward ionospheric currents over the dip equator during geomagnetic disturbances

International Nuclear Information System (INIS)

Rastogi, R.G.

1975-01-01

During geomagnetic disturbed periods, the q type of sporadic E layer near the dip equator is shown to disappear with maximum error of five minutes during the period when the difference of the geomagnetic H field between the equatorial and non-equatorial station decreases below the night level. These periods are identified with the reversal to westward direction of the electrojet currents at the base of the E region around 100 km level irrespective of the changes in the S/subq/ current system which might be produced by the disturbance

Superhydrophobic silica coating by dip coating method

International Nuclear Information System (INIS)

Mahadik, Satish A.; Parale, Vinayak; Vhatkara, Rajiv S.; Mahadik, Dinesh B.; Kavale, Mahendra S.; Wagh, Pratap B.; Gupta, Satish; Gurav, Jyoti

2013-01-01

Herein, we report a simple and low cost method for the fabrication of superhydrophobic coating surface on quartz substrates via sol-gel dip coating method at room temperature. Desired surface chemistry and texture growth for superhydrophobicity developed under double step sol–gel process at room temperature. The resultant superhydrophobic surfaces were characterized by Field-emission scanning electron microscopy (FE-SEM), Atomic force microscopy (AFM), water contact angle (WCA) measurement, differential thermal gravimetric analysis-differential thermal analysis (TGA-DTA) calorimetry and optical spectrometer. Coating shows the ultra high water contact angle about 168 ± 2° and water sliding angle 3 ± 1° and superoleophilic with petroleum oils. This approach allows a simple strategy for the fabrication process of superhydrophilic–superhydrophobic on same surfaces with high thermal stability of superhydrophobicity up to 560 °C. Thus, durability, special wettability and thermal stability of superhydrophobicity expand their application fields.

Stabilization of chlorfenvinphos in model dips using a buffer and a bacteriostat agent

International Nuclear Information System (INIS)

Kaposhi, C.K.M.; Mundia, M.P.; Nondo, J.C.; Mwangala, F.S.; Banda, R.

1997-01-01

The stability of chlorfenvinphos acaricide was studied in 50 L model dip tanks using a mixture of 14 C-labelled and unlabelled chlorfenvinphos with or without recharge. Calcium superphosphate fertilizer was used as buffer and to reduce the pH to below 5, while copper sulfate was used as a bacteriostat. In addition 50 g of sediment from around the dip tank was added to the vats and contents of vats were made up to 50 L using the water available at chalimbana NCSR farm. The buffer, by itself as well as in combination with copper sulfate stabilized chiorfenvinphos in the suspension. Binding with the sediment was a key factor in the reduction of chlorfenvinphos level, which was significantly reduced in all vats that contained sediments. Most of the acaricide bound to the sediment was not extractable. The pH in vats was maintained at 4.8 - 5.0 by the addition of superphosphate fertilizer, which reduced the degradation of chlorfenvinphos. Copper sulfate had no effect on the pH of the suspension and the vats treated with the bacteriostat had the lowest levels of chlorfenvinphos. TLC analysis also showed that acaricide breakdown was greater in non-buffered than in buffered vats. A metabolite, 2,4-dichloroacetophenone, was detected, although at a low level. A study of the leaching potential of chlorfenvinphos in soil columns showed that only 3% of the applied acaricide percolated through the 30 cm length of the column, while most of it remained soil-bound. A calorimetric method for measuring the concentration of chlorfenvinphos in dips was evaluated. The method is based on the reaction of the acaricide with 4-(4-nitrobenzyl) pyridine and subsequent measurement of the intensity of the colour formed with tetraethylene pentamine. The measurement was relatively accurate. (author)

A new design of SMES coil for bridging instantaneous voltage dips

International Nuclear Information System (INIS)

Kurusu, T; Ono, M; Ogata, H; Tosaka, T; Senda, I; Nomura, S

2006-01-01

This paper describes a new design concept of SMES coil for bridging instantaneous dips and some experimental results. The technical key point of this work is the design of a NbTi coil composed of a monolith NbTi/Cu wire for DC application. In order to cover the disadvantages of the monolith wire, some solutions have been proposed and tested using a fullscale test coil. Experimental results show the validity of the design concept of the SMES coil

Combination processes for improving storage of irradiated potatoes

International Nuclear Information System (INIS)

Shirsat, S.G.; Thomas, P.; Nair, P.M.

1990-01-01

Various combined treatments of harvested potatoes to reduce microbial spoilage of irradiated potatoes in storage were studied. Treatments studied were irradiation in conjunction with hot water dip, cold or hot salicylic acid dip, dusting with salicylic acid powder, and sodium hypochlorite wash followed by storage in well aerated containers. Microbial spoilage in irradiated potatoes was found to be greatly reduced by storage at 10deg or 15degC in well aerated containers. (M.G.B.). 9 refs., 1 tab

Hot Surface Ignition

OpenAIRE

Tursyn, Yerbatyr; Goyal, Vikrant; Benhidjeb-Carayon, Alicia; Simmons, Richard; Meyer, Scott; Gore, Jay P.

2015-01-01

Undesirable hot surface ignition of flammable liquids is one of the hazards in ground and air transportation vehicles, which primarily occurs in the engine compartment. In order to evaluate the safety and sustainability of candidate replacement fuels with respect to hot surface ignition, a baseline low lead fuel (Avgas 100 LL) and four experimental unleaded aviation fuels recommended for reciprocating aviation engines were considered. In addition, hot surface ignition properties of the gas tu...

The generation of post noon F3 layers over the dip equatorial location of Thiruvananthapuram- A new perspective

Science.gov (United States)

Mridula, N.; Pant, Tarun Kumar

2018-05-01

In the present paper, occurrence of post noon F3 layers over Thiruvananthapuram (8.5°N; 77°E; dip latitude ∼ 1.5 °N), a dip equatorial station in India have been investigated. F3 layers that occur beyond 13 IST and as observed using ground based ionosonde, for the years 2004-2008 have been studied. Our analysis shows that post noon F3 layers occur mostly on CEJ days around 16 IST to 18 IST. It is found that the time of the ionospheric E-region electric field reversal as inferred from collocated ground based magnetometer observations plays a crucial role in the generation of post noon F3 layers. In fact an early reversal of electric field emerged to be the necessary condition for the formation of post noon F3 layers. A time delay of three to 4 h is observed between the electric field reversal and the formation of F3 layer. It is proposed that this early reversal causes enhanced ionization over dip equatorial region, providing an additional ion drag to the flow of thermospheric zonal wind. This leads to accumulation of more ionization and neutrals culminating in the generation of post noon F3 layers as in the case of pre noon F3 layers. These results reveal that the generation of post noon F3 layers over the dip equatorial region is a natural consequence of the variability associated with the spatio-temporal evolution of EIA and prevailing thermospheric and ionospheric dynamics, and adds a new perspective to the present understanding.

Disaggregating Hot Water Use and Predicting Hot Water Waste in Five Test Homes

Energy Technology Data Exchange (ETDEWEB)

Henderson, H.; Wade, J.

2014-04-01

While it is important to make the equipment (or 'plant') in a residential hot water system more efficient, the hot water distribution system also affects overall system performance and energy use. Energy wasted in heating water that is not used is estimated to be on the order of 10 to 30 percent of total domestic hot water (DHW) energy use. This field monitoring project installed temperature sensors on the distribution piping (on trunks and near fixtures) and programmed a data logger to collect data at 5 second intervals whenever there was a hot water draw. This data was used to assign hot water draws to specific end uses in the home as well as to determine the portion of each hot water that was deemed useful (i.e., above a temperature threshold at the fixture). Five houses near Syracuse NY were monitored. Overall, the procedures to assign water draws to each end use were able to successfully assign about 50% of the water draws, but these assigned draws accounted for about 95% of the total hot water use in each home. The amount of hot water deemed as useful ranged from low of 75% at one house to a high of 91% in another. At three of the houses, new water heaters and distribution improvements were implemented during the monitoring period and the impact of these improvements on hot water use and delivery efficiency were evaluated.

Disaggregating Hot Water Use and Predicting Hot Water Waste in Five Test Homes

Energy Technology Data Exchange (ETDEWEB)

Henderson, Hugh [ARIES Collaborative, New York, NY (United States); Wade, Jeremy [ARIES Collaborative, New York, NY (United States)

2014-04-01

While it is important to make the equipment (or "plant") in a residential hot water system more efficient, the hot water distribution system also affects overall system performance and energy use. Energy wasted in heating water that is not used is estimated to be on the order of 10%-30% of total domestic hot water (DHW) energy use. This field monitoring project installed temperature sensors on the distribution piping (on trunks and near fixtures) in five houses near Syracuse, NY, and programmed a data logger to collect data at 5 second intervals whenever there was a hot water draw. This data was used to assign hot water draws to specific end uses in the home as well as to determine the portion of each hot water that was deemed useful (i.e., above a temperature threshold at the fixture). Overall, the procedures to assign water draws to each end use were able to successfully assign about 50% of the water draws, but these assigned draws accounted for about 95% of the total hot water use in each home. The amount of hot water deemed as useful ranged from low of 75% at one house to a high of 91% in another. At three of the houses, new water heaters and distribution improvements were implemented during the monitoring period and the impact of these improvements on hot water use and delivery efficiency were evaluated.

Relationship between hot spot residues and ligand binding hot spots in protein-protein interfaces.

Science.gov (United States)

Zerbe, Brandon S; Hall, David R; Vajda, Sandor; Whitty, Adrian; Kozakov, Dima

2012-08-27

In the context of protein-protein interactions, the term "hot spot" refers to a residue or cluster of residues that makes a major contribution to the binding free energy, as determined by alanine scanning mutagenesis. In contrast, in pharmaceutical research, a hot spot is a site on a target protein that has high propensity for ligand binding and hence is potentially important for drug discovery. Here we examine the relationship between these two hot spot concepts by comparing alanine scanning data for a set of 15 proteins with results from mapping the protein surfaces for sites that can bind fragment-sized small molecules. We find the two types of hot spots are largely complementary; the residues protruding into hot spot regions identified by computational mapping or experimental fragment screening are almost always themselves hot spot residues as defined by alanine scanning experiments. Conversely, a residue that is found by alanine scanning to contribute little to binding rarely interacts with hot spot regions on the partner protein identified by fragment mapping. In spite of the strong correlation between the two hot spot concepts, they fundamentally differ, however. In particular, while identification of a hot spot by alanine scanning establishes the potential to generate substantial interaction energy with a binding partner, there are additional topological requirements to be a hot spot for small molecule binding. Hence, only a minority of hot spots identified by alanine scanning represent sites that are potentially useful for small inhibitor binding, and it is this subset that is identified by experimental or computational fragment screening.

Energy flux of hot atoms

International Nuclear Information System (INIS)

Wotzak, G.P.; Kostin, M.D.

1976-01-01

The process in which hot atoms collide with thermal atoms of a gas, transfer kinetic energy to them, and produce additional hot atoms is investigated. A stochastic method is used to obtain numerical results for the spatial and time dependent energy flux of hot atoms in a gas. The results indicate that in hot atom systems a front followed by an intense energy flux of hot atoms may develop

Modelling Hot Air Balloons.

Science.gov (United States)

Brimicombe, M. W.

1991-01-01

A macroscopic way of modeling hot air balloons using a Newtonian approach is presented. Misleading examples using a car tire and the concept of hot air rising are discussed. Pressure gradient changes in the atmosphere are used to explain how hot air balloons work. (KR)

Preparation and characterization of 304 stainless steel/Q235 carbon steel composite material

Science.gov (United States)

Shen, Wenning; Feng, Lajun; Feng, Hui; Cao, Ying; Liu, Lei; Cao, Mo; Ge, Yanfeng

The composite material of 304 stainless steel reinforced Q235 carbon steel has been prepared by modified hot-rolling process. The resulted material was characterized by scanning electron microscope, three-electrode method, fault current impact method, electrochemical potentiodynamic polarization curve measurement and electrochemical impedance spectroscopy. The results showed that metallurgical bond between the stainless steel layer and carbon steel substrate has been formed. The composite material exhibited good electrical conductivity and thermal stability. The average grounding resistance of the composite material was about 13/20 of dip galvanized steel. There has no surface crack and bubbling formed after fault current impact. The composite material led to a significant decrease in the corrosion current density in soil solution, compared with that of hot dip galvanized steel and bare carbon steel. On the basis polarization curve and EIS analyses, it can be concluded that the composite material showed improved anti-corrosion property than hot-dip galvanized steel.

Morphological and microstructural studies on aluminizing coating of carbon steel

Energy Technology Data Exchange (ETDEWEB)

Samsu, Zaifol; Othman, Norinsan Kamil; Daud, Abd Razak; Hussein, Hishammuddin [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

2013-11-27

Hot dip aluminizing is one of the most effective methods of surface protection for steels and is gradually gaining popularity. The morphology and microstructure of an inter-metallic layer form on the surface of low carbon steel by hot dip aluminization treatment had been studied in detail. This effect has been investigated using optical and scanning electron microscopy, and X-ray diffraction. The result shows that the reaction between the steel and the molten aluminium leads to the formation of Fe–Al inter-metallic compounds on the steel surface. X-ray diffraction and electron microscopic studies showed that a two layer coating was formed consisting of an external Al layer and a (Fe{sub 2}Al{sub 5}) inter metallic on top of the substrate after hot dip aluminizing process. The inter-metallic layer is ‘thick’ and exhibits a finger-like growth into the steel. Microhardness testing shown that the intermetallic layer has high hardness followed by steel substrate and the lowest hardness was Al layer.

Effect of Process Variables on the Grain Size and Crystallographic Texture of Hot-Dip Galvanized Coatings

Science.gov (United States)

Kaboli, Shirin; McDermid, Joseph R.

2014-08-01

A galvanizing simulator was used to determine the effect of galvanizing bath antimony (Sb) content, substrate surface roughness, and cooling rate on the microstructural development of metallic zinc coatings. Substrate surface roughness was varied through the use of relatively rough hot-rolled and relatively smooth bright-rolled steels, cooling rates were varied from 0.1 to 10 K/s, and bulk bath Sb levels were varied from 0 to 0.1 wt pct. In general, it was found that increasing bath Sb content resulted in coatings with a larger grain size and strongly promoted the development of coatings with the close-packed {0002} basal plane parallel to the substrate surface. Increasing substrate surface roughness tended to decrease the coating grain size and promoted a more random coating crystallographic texture, except in the case of the highest Sb content bath (0.1 wt pct Sb), where substrate roughness had no significant effect on grain size except at higher cooling rates (10 K/s). Increased cooling rates tended to decrease the coating grain size and promote the {0002} basal orientation. Calculations showed that increasing the bath Sb content from 0 to 0.1 wt pct Sb increased the dendrite tip growth velocity from 0.06 to 0.11 cm/s by decreasing the solid-liquid interface surface energy from 0.77 to 0.45 J/m2. Increased dendrite tip velocity only partially explains the formation of larger zinc grains at higher Sb levels. It was also found that the classic nucleation theory cannot completely explain the present experimental observations, particularly the effect of increasing the bath Sb, where the classical theory predicts increased nucleation and a finer grain size. In this case, the "poisoning" theory of nucleation sites by segregated Sb may provide a partial explanation. However, any analysis is greatly hampered by the lack of fundamental thermodynamic information such as partition coefficients and surface energies and by a lack of fundamental structural studies. Overall

Buildup of electrons with hot electron beam injection into a homogeneous magnetic field

International Nuclear Information System (INIS)

Bashko, V.A.; Krivoruchko, A.M.; Tarasov, I.K.

1989-01-01

The injection of the monoenergetic beam of electrons into the vacuum drift channel under the conditions when the beam current exceeds a certain threshold value involves a virtual cathode creation. The process of virtual cathode creation leads to an exchange of one-fluid movement of beam particles to three-fluid one corresponding to incident, reflected and passed through anticathode beam particles. For the monoenergetic beam case when the velocity spread Δv dr (v dr is the beam drift velocity), the beam instability was predicted in theory and was observed in experiment. Meanwhile, the injection in the drift space of the 'hot' beam having finite spread in velocities may be accompanied not only by the reflection of particles if their velocity v 1/2 (where φ is the electrostatic potential dip value, e and m are the electron charge and mass, respectively), but also the mutual Coulomb scattering of incident and reflected electrons. The scattering process leads in its turn to appearance of viscosity forces and to trapping of a part of beam electrons into the effective potential well formed by electrostatic potential dip and the viscous force potential. The interaction of travelling and trapped particles may occur even at the stage preceding the virtual electrode formation and it may influence the process of its appearance and also the current flow through the drift space. In this report there are described the experimental results on accumulation of electrons when electron beam propagates in vacuum and has a large spread in particle velocities Δv dr in the homogeneous longitudinal magnetic field when ω pe He where ω pe is the electron Langmuir frequency of beam electrons, ω He is the electron cyclotron frequency. (author) 6 refs., 2 figs

Software Simulation of Hot Tearing

DEFF Research Database (Denmark)

Andersen, S.; Hansen, P.N.; Hattel, Jesper Henri

1999-01-01

The brittleness of a solidifying alloy in a temperature range near the solidus temperature has been recognised since the fifties as the mechanism responsible for hot tearing. Due to this brittlenes, the metal will crack under even small amounts of strain in that temperature range. We see these hot...... tears in castings close to hot centres, where the level of strain is often too high.Although the hot tearing mechanism is well understood, until now it has been difficult to do much to reduce the hot tearing tendency in a casting. In the seventies, good hot tearing criteria were developed by considering...... the solidification rate and the strain rate of the hot tear prone areas. But, until recently it was only possible to simulate the solidification rate, so that the criteria could not be used effectively.Today, with new software developments, it is possible to also simulate the strain rate in the hot tear prone areas...

The study of importance sampling in Monte-carlo calculation of blocking dips

International Nuclear Information System (INIS)

Pan Zhengying; Zhou Peng

1988-01-01

Angular blocking dips around the axis in Al single crystal of α-particles of about 2 Mev produced at a depth of 0.2 μm are calculated by a Monte-carlo simulation. The influence of the small solid angle emission of particles and the importance sampling in the solid angle emission have been investigated. By means of importance sampling, a more reasonable results with high accuracy are obtained

Blood Pressure Treatment Adherence and Control after Participation in the ReHOT

Directory of Open Access Journals (Sweden)

Nathália Silva de Jesus

Full Text Available Abstract Background: Lack of adherence to pharmacological treatment is one of the main causes of low control rates in hypertension. Objective: To verify treatment adherence and associated factors, as well as blood pressure (BP control in participants of the Resistant Hypertension Optimal Treatment (ReHOT clinical trial. Method: Cross-sectional study including all 109 patients who had completed the ReHOT for at least 6 months. We excluded those participants who failed to respond to the new recruitment after three phone contact attempts. We evaluated the BP control by ambulatory BP monitoring (ABPM; controlled levels: 24-hour systolic and diastolic BP < 130 x 80 mmHg and analyzed the patients' treatment adherence using the Morisky Medication Adherence Scale (MMAS questionnaire validated by Bloch, Melo, and Nogueira (2008. The statistical analysis was performed with the software IBM SPSS statistics 21.0. We tested the normality of the data distribution with kurtosis and skewness. The variables tested in the study are presented with descriptive statistics. Comparisons between treatment adherence and other variables were performed with Student's t test for independent variables and Pearson's chi-square or Fisher's exact test. To conduct analyses among patients considering adherence to treatment and BP control, we created four groups: G0, G1, G2, and G3. We considered a 5% significance level in all tests. Results: During the ReHOT, 80% of the patients had good BP control and treatment adherence. Of 96 patients reevaluated in the present study, only 52.1% had controlled hypertension when assessed by ABPM, while 31.3% were considered adherent by the MMAS. Regarding other ABPM measures, we observed an absence of a nocturnal dip in 64.6% of the patients and a white-coat effect and false BP control in 23% and 12.5%, respectively. Patients' education level showed a trend towards being a determinant factor associated with lack of adherence (p = 0

Rupture Dynamics along Thrust Dipping Fault: Inertia Effects due to Free Surface Wave Interactions

Science.gov (United States)

Vilotte, J. P.; Scala, A.; Festa, G.

2017-12-01

We numerically investigate the dynamic interaction between free surface and up-dip, in-plane rupture propagation along thrust faults, under linear slip-weakening friction. With reference to shallow along-dip rupture propagation during large subduction earthquakes, we consider here low dip-angle fault configurations with fixed strength excess and depth-increasing initial stress. In this configuration, the rupture undergoes a break of symmetry with slip-induced normal stress perturbations triggered by the interaction with reflected waves from the free surface. We found that both body-waves - behind the crack front - and surface waves - at the crack front - can trigger inertial effects. When waves interact with the rupture before this latter reaches its asymptotic speed, the rupture can accelerate toward the asymptotic speed faster than in the unbounded symmetric case, as a result of these inertial effects. Moreover, wave interaction at the crack front also affects the slip rate generating large ground motion on the hanging wall. Imposing the same initial normal stress, frictional strength and stress drop while varying the static friction coefficient we found that the break of symmetry makes the rupture dynamics dependent on the absolute value of friction. The higher the friction the stronger the inertial effect both in terms of rupture acceleration and slip amount. When the contact condition allows the fault interface to open close to the free surface, the length of the opening zone is shown to depend on the propagation length, the initial normal stress and the static friction coefficient. These new results are shown to agree with analytical results of rupture propagation in bounded media, and open new perspectives for understanding the shallow rupture of large subduction earthquakes and tsunami sources.

Hot tub folliculitis

Science.gov (United States)

... survives in hot tubs, especially tubs made of wood. Symptoms The first symptom of hot tub folliculitis ... may help prevent the problem. Images Hair follicle anatomy References D'Agata E. Pseudomonas aeruginosa and other ...

Hot conditioning equipment conceptual design report

International Nuclear Information System (INIS)

Bradshaw, F.W.

1996-01-01

This report documents the conceptual design of the Hot Conditioning System Equipment. The Hot conditioning System will consist of two separate designs: the Hot Conditioning System Equipment; and the Hot Conditioning System Annex. The Hot Conditioning System Equipment Design includes the equipment such as ovens, vacuum pumps, inert gas delivery systems, etc.necessary to condition spent nuclear fuel currently in storage in the K Basins of the Hanford Site. The Hot Conditioning System Annex consists of the facility of house the Hot Conditioning System. The Hot Conditioning System will be housed in an annex to the Canister Storage Building. The Hot Conditioning System will consist of pits in the floor which contain ovens in which the spent nuclear will be conditioned prior to interim storage

Hot conditioning equipment conceptual design report

Energy Technology Data Exchange (ETDEWEB)

Bradshaw, F.W., Westinghouse Hanford

1996-08-06

This report documents the conceptual design of the Hot Conditioning System Equipment. The Hot conditioning System will consist of two separate designs: the Hot Conditioning System Equipment; and the Hot Conditioning System Annex. The Hot Conditioning System Equipment Design includes the equipment such as ovens, vacuum pumps, inert gas delivery systems, etc.necessary to condition spent nuclear fuel currently in storage in the K Basins of the Hanford Site. The Hot Conditioning System Annex consists of the facility of house the Hot Conditioning System. The Hot Conditioning System will be housed in an annex to the Canister Storage Building. The Hot Conditioning System will consist of pits in the floor which contain ovens in which the spent nuclear will be conditioned prior to interim storage.

Effects of postharvest salicylic acid dipping on Alternaria rot and disease resistance of jujube fruit during storage.

Science.gov (United States)

Cao, Jiankang; Yan, Jiaqi; Zhao, Yumei; Jiang, Weibo

2013-10-01

Considerable postharvest losses caused by Alternaria alternata often occur in Chinese jujube fruit, and synthetic fungicides have been widely used to protect the fruit from Alternaria rot. However, the potential harmfulness of fungicide residues to human health and the environment cannot be ignored. This study was conducted to develop an alternative approach for controlling postharvest disease by inducing fruit resistance with salicylic acid (SA) dipping. Disease incidence and lesion area in the jujube fruit inoculated with A. alternata were significantly inhibited by 2 and 2.5 mmol L(-1) SA dipping. Naturally infected decay rate and index in jujubes were also significantly reduced by SA dipping during long-term storage at 0°C. SA enhanced activities of the main defense-related enzymes including phenylalanine ammonia-lyase, peroxidase, chitinase and β-1,3-glucanase in the fruit during storage. SA strongly decreased catalase activity but increased superoxide dismutase activity and ascorbic acid content in jujubes. The beneficial effects of SA on fruit protection may be due to its ability to activate several highly coordinated defence-related systems in jujubes, instead of its fungicidal activity. The findings indicated that application of SA would offer an alternative approach that helps to control postharvest disease and maintain storage quality in fruits. © 2013 Society of Chemical Industry.

Estimation of shear velocity contrast for dipping or anisotropic medium from transmitted Ps amplitude variation with ray-parameter

Science.gov (United States)

Kumar, Prakash

2015-12-01

Amplitude versus offset analysis of P to P reflection is often used in exploration seismology for hydrocarbon exploration. In the present work, the feasibility to estimate crustal velocity structure from transmitted P to S wave amplitude variation with ray-parameter has been investigated separately for dipping layer and anisotropy medium. First, for horizontal and isotropic medium, the approximation of P-to-s conversion is used that is expressed as a linear form in terms of slowness. Next, the intercept of the linear regression has been used to estimate the shear wave velocity contrast (δβ) across an interface. The formulation holds good for isotropic and horizontal layer medium. Application of such formula to anisotropic medium or dipping layer data may lead to erroneous estimation of δβ. In order to overcome this problem, a method has been proposed to compensate the SV-amplitude using shifted version of SH-amplitude, and subsequently transforming SV amplitudes equivalent to that from isotropic or horizontal layer medium as the case may be. Once this transformation has been done, δβ can be estimated using isotropic horizontal layer formula. The shifts required in SH for the compensation are π/2 and π/4 for dipping layer and anisotropic medium, respectively. The effectiveness of the approach has been reported using various synthetic data sets. The methodology is also tested on real data from HI-CLIMB network in Himalaya, where the presence of dipping Moho has already been reported. The result reveals that the average shear wave velocity contrast across the Moho is larger towards the Indian side compared to the higher Himalayan and Tibetan regions.

A facile dip-coating process for preparing highly durable superhydrophobic surface with multi-scale structures on paint films.

Science.gov (United States)

Cui, Zhe; Yin, Long; Wang, Qingjun; Ding, Jianfu; Chen, Qingmin

2009-09-15

Superhydrophobic surfaces with multi-scale nano/microstructures have been prepared on epoxy paint surfaces using a feasible dip-coating process. The microstructures with 5-10 microm protuberances were first prepared on epoxy paint surface by sandblast. Then the nanostructures were introduced on the microstructure surface by anchoring 50-100 nm SiO(2) particles (nano-SiO(2)) onto the sandblasted paint surface, which was completed by dip-coating with a nano-SiO(2)/epoxy adhesive solution (M1). At last the surface was further modified for enhancing hydrophobicity by another dip-coating with a solution of a low surface energy polymer, aminopropyl terminated polydimethylsiloxane (ATPS) modified epoxy adhesive (M2). The water contact angle of the as-prepared samples reached as high as 167.8 degrees and the sliding angle was 7 degrees. The prepared superhydrophobic surface exhibited excellent durability to the high speed scouring test and high stability in neutral and basic aqueous solutions and some common organic solvents. In addition, this method can be adopted to fabricate large scale samples with a good homogeneity of the whole surface at very low cost.

Numerical analysis of the effects induced by normal faults and dip angles on rock bursts

Science.gov (United States)

Jiang, Lishuai; Wang, Pu; Zhang, Peipeng; Zheng, Pengqiang; Xu, Bin

2017-10-01

The study of mining effects under the influences of a normal fault and its dip angle is significant for the prediction and prevention of rock bursts. Based on the geological conditions of panel 2301N in a coalmine, the evolution laws of the strata behaviors of the working face affected by a fault and the instability of the fault induced by mining operations with the working face of the footwall and hanging wall advancing towards a normal fault are studied using UDEC numerical simulation. The mechanism that induces rock burst is revealed, and the influence characteristics of the fault dip angle are analyzed. The results of the numerical simulation are verified by conducting a case study regarding the microseismic events. The results of this study serve as a reference for the prediction of rock bursts and their classification into hazardous areas under similar conditions.

Harvest maturity and post-processing dip to improve quality of fresh-cut carambola fruit

Science.gov (United States)

'Arkin' carambola (Averrhoa carambola L.) fruit harvested at color break or full yellow stage were washed with or without an alkaline solution (pH 13.5), cut to 1 cm thick slices, dipped in calcium ascorbate (Ca ASA), ascorbic acid (ASA) or water, and packaged in perforated clamshells for up to 14 d...

Mathematical Modeling of Microwave-Assisted Convective Heating and Drying of Grapes

Science.gov (United States)

This research studied the processing performance and product quality of Thompson seedless grapes dried using microwave-assisted convective hot air drying as well as the effect of blanching and dipping pretreatments. Two pretreatment methods were compared, dipping into 2% ethyl oleate (V/V) and 5% p...

WESF hot cells waste minimization criteria hot cells window seals evaluation

International Nuclear Information System (INIS)

Walterskirchen, K.M.

1997-01-01

WESF will decouple from B Plant in the near future. WESF is attempting to minimize the contaminated solid waste in their hot cells and utilize B Plant to receive the waste before decoupling. WESF wishes to determine the minimum amount of contaminated waste that must be removed in order to allow minimum maintenance of the hot cells when they are placed in ''laid-up'' configuration. The remaining waste should not cause unacceptable window seal deterioration for the remaining life of the hot cells. This report investigates and analyzes the seal conditions and hot cell history and concludes that WESF should remove existing point sources, replace cerium window seals in F-Cell and refurbish all leaded windows (except for A-Cell). Work should be accomplished as soon as possible and at least within the next three years

10 CFR 431.102 - Definitions concerning commercial water heaters, hot water supply boilers, and unfired hot water...

Science.gov (United States)

2010-01-01

... supply boilers, and unfired hot water storage tanks. 431.102 Section 431.102 Energy DEPARTMENT OF ENERGY... Water Heaters, Hot Water Supply Boilers and Unfired Hot Water Storage Tanks § 431.102 Definitions concerning commercial water heaters, hot water supply boilers, and unfired hot water storage tanks. The...

Annealing treatments for producing cold-rolled low-silicon multi-phase steels for automotive applications

Energy Technology Data Exchange (ETDEWEB)

Vrieze, J.; Vortrefflich, W.; Winter, L. de [Applied Physical Metallurgy, Hoogovens Research and Development, Ijmuiden (Netherlands)

2000-07-01

Laboratory simulations of a hot-dip galvanizing line have been carried out on a 0.16%C-1.5%Mn-0.4%Si steel. It has been demonstrated that based on this steel composition materials with typical multi-phase properties can be produced on hot-dip galvanizing lines. By varying the process conditions a tensile strength between 570 and 650 MPa has been obtained. In addition, tensile tests at high strain rates have been carried out and the results have been compared with those of other non-multi-phase steel grades. (orig.)

Identification of small-scale discontinuities based on dip-oriented gradient energy entropy coherence estimation

Science.gov (United States)

Peng, Da; Yin, Cheng

2017-09-01

Locating small-scale discontinuities is one of the most challenging geophysical tasks; these subtle geological features are significant since they are often associated with subsurface petroleum traps. Subtle faults, fractures, unconformities, reef textures, channel boundaries, thin-bed boundaries and other structural and stratigraphic discontinuities have subtle geological edges which may provide lateral variation in seismic expression. Among the different geophysical techniques available, 3D seismic discontinuity attributes are particularly useful for highlighting discontinuities in the seismic data. Traditional seismic discontinuity attributes are sensitive to noise and are not very appropriate for detecting small-scale discontinuities. Thus, we present a dip-oriented gradient energy entropy (DOGEE) coherence estimation method to detect subtle faults and structural features. The DOGEE coherence estimation method uses the gradient structure tensor (GST) algorithm to obtain local dip information and construct a gradient correlation matrix to calculate gradient energy entropy. The proposed DOGEE coherence estimation method is robust to noise, and also improves the clarity of fault edges. It is effective for small-scale discontinuity characterisation and interpretation.

Determination of solid-liquid partition coefficients (Kd) for diazinon, propetamphos and cis-permethrin: implications for sheep dip disposal

International Nuclear Information System (INIS)

Cooke, Cindy M.; Shaw, George; Lester, John N.; Collins, Chris D.

2004-01-01

Two groups of chemicals are currently licensed for use in sheep dip products in the UK. These are organophosphate (OP) insecticides and synthetic pyrethroid (SP) insecticides. SPs are deemed to be less toxic to human health than OPs, although they are approximately 100 times more toxic to some elements of the aquatic environment. Three insecticides were selected for experimental investigation: diazinon, propetamphos (OPs) and cis-permethrin (SP), representative of the active ingredients used in sheep dip formulations, with additional uses in insect control in crops, and for domestic control of flies, mosquitoes, cockroaches, lice, ticks and spiders. The UK Government has recently reviewed agricultural practices relating to the disposal of used sheep dip, because the constituent insecticides are frequently detected in UK watercourses and the presence of these compounds is a severe hazard to the aquatic environment. Standard batch sorption experiments were carried out to investigate insecticide partitioning from water to soil, and the relationship between sorption and soil organic carbon content is discussed. Sorption isotherms and K d values showed that cis-permethrin adsorption was fastest on all five soils investigated, exhibiting the greatest total partitioning to the soil phase (83.8-94.8%) and high resistance to desorption. In comparison, the OP insecticides exhibited moderately strong soil adsorption as evidenced by their K d coefficients (diazinon K d 12-35 and propetamphos K d 9-60), with low sorption reversibility (<15%). Calculation of a hydrological retardation factor in a scenario representative of a typical UK environment suggested that SP insecticides such as cis-permethrin will not migrate in the soil profile due to their virtual immobility and strong soil retention, and thus waste sheep dip disposal to agricultural land should not pose a risk to aquatic life if applied with appropriate controls

From lifting to planting: Root dip treatments affect survival of loblolly pine (Pinus taeda)

Science.gov (United States)

Tom E. Starkey; David B. South

2009-01-01

Hydrogels and clay slurries are the materials most commonly applied to roots of pines in the southern United States. Most nursery managers believe such applications offer a form of "insurance" against excessive exposure during planting. The objective of this study was to examine the ability of root dip treatments to: (1) support fungal growth; and (2) protect...

Hot springs in Hokuriku District

Energy Technology Data Exchange (ETDEWEB)

Sato, K. (Hot Springs Research Center, Japan)

1971-01-01

In the Hokuriku district including Toyama, Ishikawa, and Fukui Prefectures, hot springs of more than 25/sup 0/C were investigated. In the Toyama Prefecture, there are 14 hot springs which are located in an area from the Kurobe River to the Tateyama volcano and in the mountainous area in the southwest. In Ishikawa Prefecture there are 16 hot springs scattered in Hakusan and its vicinity, the Kaga mountains, and in the Noto peninsula. In northern Fukui Prefecture there are seven hot springs. The hot springs in Shirakawa in Gifu Prefecture are characterized as acid springs producing exhalations and H/sub 2/S. These are attributed to the Quaternary volcanoes. The hot springs of Wakura, Katayamazu, and Awara in Ishikawa Prefecture are characterized by a high Cl content which is related to Tertiary andesite. The hot springs of Daishoji, Yamanaka, Yamashiro, Kuritsu, Tatsunokuchi, Yuwaku, and Yunotani are characterized by a low HCO/sub 3/ content. The Ca and SO/sub 4/ content decreases from east to west, and the Na and Cl content increases from west to east. These fluctuations are related to the Tertiary tuff and rhyolite. The hot springs of Kuronagi, Kinshu, and Babadani, located along the Kurobe River are characterized by low levels of dissolved components and high CO/sub 2/ and HCO/sub 3/ content. These trends are related to late Paleozoic granite. Hot springs resources are considered to be connected to geothermal resources. Ten tables, graphs, and maps are provided.

Social influences on ant-dipping acquisition in the wild chimpanzees (Pan troglodytes verus) of Bossou, Guinea, West Africa.

Science.gov (United States)

Humle, Tatyana; Snowdon, Charles T; Matsuzawa, Tetsuro

2009-10-01

We currently have little understanding of the influence of learning opportunity, whether social or environmental, and maternal role on tool-use acquisition in young wild chimpanzees. This study aims to fill this gap by focusing on the acquisition of ant-dipping among chimpanzees of Bossou, Guinea. Ant-dipping is a hazardous tool-use behaviour aimed at army ants (Dorylus spp.). Bossou chimpanzees target these ants both at nests (high risk) and trails (low risk) and employ two techniques to consume them: direct mouthing and pull-through. We present data for 13 mother-offspring pairs (1-10 years old). Mothers with young chimpanzee material culture is a product of a complex interaction between social processes and ecological factors.

The role of magmatic loads and rift jumps in generating seaward dipping reflectors on volcanic rifted margins

Science.gov (United States)

Buck, W. Roger

2017-05-01

The largest volcanic constructs on Earth are the seismically imaged seaward dipping reflector (SDR) units found offshore of many rifted continental margins, including most that border the Atlantic Ocean. Whether their formation requires large magnitude (i.e. 10 s of km) of normal fault slip or results from the deflection of the lithosphere by the weight of volcanic flows is controversial. Though there is evidence for faulting associated with some SDRs, this paper considers the range of structures that can be produced by magmatic and volcanic loading alone. To do this an idealized mechanical model for the construction of rift-related volcanic flow structures is developed. Dikes open as plates move away from the center of a model rift and volcanic flows fill the depression produced by the load caused by dike solidification. The thin elastic plate flexure approximation allows a closed form description of the shape of both the contacts between flows and between the flows and underlying dikes. The model depends on two independent parameters: the flexure parameter, α, and the maximum isostatically supported extrusive layer thickness, w0. For reasonable values of these parameters the model reproduces the observed down-dip thickening of flows and the range of reflector dip angles. A numerical scheme using the analytic results allows simulation of the effect of temporal changes in the locus of magmatic spreading as well as changes in the amount of volcanic infill. Either jumps in the location of the center of diking or periods with no volcanism result in separate units or "packages" of model SDRs, in which the flow-dike contact dips landward, consistent with observations previously attributed only to listric normal fault offset. When jumps in the spreading center are small (i.e. less than α) they result in thicker, narrower volcanic units on one side of a rift compared to those on the other side. This is similar to the asymmetric distributions of volcanic packages seen

Detection of Hot Halo Gets Theory Out of Hot Water

Science.gov (United States)

2006-02-01

Scientists using NASA's Chandra X-ray Observatory have detected an extensive halo of hot gas around a quiescent spiral galaxy. This discovery is evidence that galaxies like our Milky Way are still accumulating matter from the gradual inflow of intergalactic gas. "What we are likely witnessing here is the ongoing galaxy formation process," said Kristian Pedersen of the University of Copenhagen, Denmark, and lead author of a report on the discovery. Chandra observations show that the hot halo extends more than 60,000 light years on either side of the disk of the galaxy known as NGC 5746. The detection of such a large halo alleviates a long-standing problem for the theory of galaxy formation. Spiral galaxies are thought to form from enormous clouds of intergalactic gas that collapse to form giant, spinning disks of stars and gas. Chandra X-ray Image of NGC 5746 Chandra X-ray Image of NGC 5746 One prediction of this theory is that large spiral galaxies should be immersed in halos of hot gas left over from the galaxy formation process. Hot gas has been detected around spiral galaxies in which vigorous star formation is ejecting matter from the galaxy, but until now hot halos due to infall of intergalactic matter have not been detected. "Our observations solve the mystery of the missing hot halos around spiral galaxies," said Pedersen. "The halos exist, but are so faint that an extremely sensitive telescope such as Chandra is needed to detect them." DSS Optical Image of NGC 5746 DSS Optical Image of NGC 5746 NGC 5746 is a massive spiral galaxy about a 100 million light years from Earth. Its disk of stars and gas is viewed almost edge-on. The galaxy shows no signs of unusual star formation, or energetic activity from its nuclear region, making it unlikely that the hot halo is produced by gas flowing out of the galaxy. "We targeted NGC 5746 because we thought its distance and orientation would give us the best chance to detect a hot halo caused by the infall of

An initial response of magnetic fields at geosynchronous orbit to Pi 2 onset as observed from the dip-equator

Directory of Open Access Journals (Sweden)

O. Saka

1998-05-01

Full Text Available Fluxgate magnetometer data recorded at the dip-equator (Huancayo, Peru; 1.44°N, 355.9° in geomagnetic coordinates; 12.1°S, 75.2°W in geographic coordinates; L = 1.00 with higher accuracy of timing (0.1 s and amplitude resolution (0.01 nT were utilized to survey an onset of Pi 2 pulsations in the midnight sector (2100–0100 LT during PROMIS (Polar Region and Outer Magnetosphere International Study periods (1 March–20 June, 1986. It is found that changing field line magnitude and vector as observed by magnetometer on board the synchronous satellites in the midnight sector often takes place simultaneously with the onset of Pi 2 pulsations at the dip-equator. The field disturbances that follow thereafter tend to last for some time both at the geosynchronous altitudes and the dip-equator. In this report, we examine the initial response of the field lines in space, and attempt to classify how the field line vector changed in the meridional plane. Key words. Magnetospheric physics · Magnetospheric configuration and dynamics · MHD waves and instabilities · Plasmasphere

An initial response of magnetic fields at geosynchronous orbit to Pi 2 onset as observed from the dip-equator

Directory of Open Access Journals (Sweden)

O. Saka

Full Text Available Fluxgate magnetometer data recorded at the dip-equator (Huancayo, Peru; 1.44°N, 355.9° in geomagnetic coordinates; 12.1°S, 75.2°W in geographic coordinates; L = 1.00 with higher accuracy of timing (0.1 s and amplitude resolution (0.01 nT were utilized to survey an onset of Pi 2 pulsations in the midnight sector (2100–0100 LT during PROMIS (Polar Region and Outer Magnetosphere International Study periods (1 March–20 June, 1986. It is found that changing field line magnitude and vector as observed by magnetometer on board the synchronous satellites in the midnight sector often takes place simultaneously with the onset of Pi 2 pulsations at the dip-equator. The field disturbances that follow thereafter tend to last for some time both at the geosynchronous altitudes and the dip-equator. In this report, we examine the initial response of the field lines in space, and attempt to classify how the field line vector changed in the meridional plane.

Key words. Magnetospheric physics · Magnetospheric configuration and dynamics · MHD waves and instabilities · Plasmasphere

Hot Gas Halos in Galaxies

Science.gov (United States)

Mulchaey, John

Most galaxy formation models predict that massive low-redshift disk galaxies are embedded in extended hot halos of externally accreted gas. Such gas appears necessary to maintain ongoing star formation in isolated spirals like the Milky Way. To explain the large population of red galaxies in rich groups and clusters, most galaxy evolution models assume that these hot gas halos are stripped completely when a galaxy enters a denser environment. This simple model has been remarkably successful at reproducing many observed properties of galaxies. Although theoretical arguments suggest hot gas halos are an important component in galaxies, we know very little about this gas from an observational standpoint. In fact, previous observations have failed to detect soft X-ray emission from such halos in disk galaxies. Furthermore, the assumption that hot gas halos are stripped completely when a galaxy enters a group or cluster has not been verified. We propose to combine proprietary and archival XMM-Newton observations of galaxies in the field, groups and clusters to study how hot gas halos are impacted by environment. Our proposed program has three components: 1) The deepest search to date for a hot gas halo in a quiescent spiral galaxy. A detection will confirm a basic tenet of disk galaxy formation models, whereas a non-detection will seriously challenge these models and impose new constraints on the growth mode and feedback history of disk galaxies. 2) A detailed study of the hot gas halos properties of field early-type galaxies. As environmental processes such as stripping are not expected to be important in the field, a study of hot gas halos in this environment will allow us to better understand how feedback and other internal processes impact hot gas halos. 3) A study of hot gas halos in the outskirts of groups and clusters. By comparing observations with our suite of simulations we can begin to understand what role the stripping of hot gas halos plays in galaxy

Durability of light steel framing in residential applications

OpenAIRE

Lawson, RM; Popo-Ola, S.O.; Way, A.; Heatley, T; Pedreschi, Remo

2010-01-01

This paper presents a summary and analysis of research findings on the durability of galvanised cold-formed steel sections used in housing in order to deduce their design life. These cold-formed sections are produced from pre-galvanised strip steel. It reviews reports and publications from research projects carried out by Corus and the Steel Construction Institute on zinc-coated, cold-formed steel products. New data have also been gathered from measurements on houses and similar buildings tha...

Hot flashes and sleep in women.

Science.gov (United States)

Moe, Karen E

2004-12-01

Sleep disturbances during menopause are often attributed to nocturnal hot flashes and 'sweats' associated with changing hormone patterns. This paper is a comprehensive critical review of the research on the relationship between sleep disturbance and hot flashes in women. Numerous studies have found a relationship between self-reported hot flashes and sleep complaints. However, hot flash studies using objective sleep assessment techniques such as polysomnography, actigraphy, or quantitative analysis of the sleep EEG are surprisingly scarce and have yielded somewhat mixed results. Much of this limited evidence suggests that hot flashes are associated with objectively identified sleep disruption in at least some women. At least some of the negative data may be due to methodological issues such as reliance upon problematic self-reports of nocturnal hot flashes and a lack of concurrent measures of hot flashes and sleep. The recent development of a reliable and non-intrusive method for objectively identifying hot flashes during the night should help address the need for substantial additional research in this area. Several areas of clinical relevance are described, including the effects of discontinuing combined hormone therapy (estrogen plus progesterone) or estrogen-only therapy, the possibility of hot flashes continuing for many years after menopause, and the link between hot flashes and depression.

Preparation and characterization of 304 stainless steel/Q235 carbon steel composite material

Directory of Open Access Journals (Sweden)

Wenning Shen

Full Text Available The composite material of 304 stainless steel reinforced Q235 carbon steel has been prepared by modified hot-rolling process. The resulted material was characterized by scanning electron microscope, three-electrode method, fault current impact method, electrochemical potentiodynamic polarization curve measurement and electrochemical impedance spectroscopy. The results showed that metallurgical bond between the stainless steel layer and carbon steel substrate has been formed. The composite material exhibited good electrical conductivity and thermal stability. The average grounding resistance of the composite material was about 13/20 of dip galvanized steel. There has no surface crack and bubbling formed after fault current impact. The composite material led to a significant decrease in the corrosion current density in soil solution, compared with that of hot dip galvanized steel and bare carbon steel. On the basis polarization curve and EIS analyses, it can be concluded that the composite material showed improved anti-corrosion property than hot-dip galvanized steel. Keywords: Stainless steel, Carbon steel, Anti-corrosion, Conductivity, Electrochemical, EIS

Update on the KELT Transit Survey: Hot Planets around Hot Stars

Science.gov (United States)

Gaudi, B. Scott; Stassun, Keivan G.; Pepper, Joshua; KELT Collaboration

2018-01-01

The KELT Transit Survey consists of a pair of small-aperture, wide-angle automated telescopes located at Winer Observatory in Sonoita, Arizona and the South African Astronomical Observatory (SAAO) in Sutherland, South Africa. Together, they are surveying roughly 70% of the sky for transiting planets. By virtue of their small apertures (42 mm) and large fields-of-view (26 degrees x 26 degrees), KELT is most sensitive to hot Jupiters transiting relatively bright (V~8-11), and thus relatively hot stars. I will provide an update on the planets discovered by KELT, focusing in detail on our recent discoveries of very hot planets transiting several bright A and early F stars.

Hot subluminous star: HDE 283048

International Nuclear Information System (INIS)

Laget, M.; Vuillemin, A.; Parsons, S.B.; Henize, K.G.; Wray, J.D.

1978-01-01

The star HDE 283048, located at α = 3/sup h/50/sup m/.3, delta = +25 0 36', shows a strong ultraviolet continuum. Ground-based observations indicate a hot-dominated composite spectrum. Several lines of evidence suggest that the hot component is a hot subdwarf. 2 figures

Kondo peak splitting and Kondo dip in single molecular magnet junctions

Energy Technology Data Exchange (ETDEWEB)

Niu, Pengbin, E-mail: 120233951@qq.com [Institute of Solid State Physics, Shanxi Datong University, Datong 037009 (China); Shi, Yunlong; Sun, Zhu [Institute of Solid State Physics, Shanxi Datong University, Datong 037009 (China); Nie, Yi-Hang [Institute of Theoretical Physics, Shanxi University, Taiyuan 030006 (China); Luo, Hong-Gang [Center for Interdisciplinary Studies & Key Laboratory for Magnetism and Magnetic Materials of the MoE, Lanzhou University, Lanzhou 730000 (China); Beijing Computational Science Research Center, Beijing 100084 (China)

2016-01-15

Many factors containing bias, spin–orbit coupling, magnetic fields applied, and so on can strongly influence the Kondo effect, and one of the consequences is Kondo peak splitting (KPS). It is natural that KPS should also appear when another spin degree of freedom is involved. In this work we study the KPS effects of single molecular magnets (SMM) coupled with two metallic leads in low-temperature regime. It is found that the Kondo transport properties are strongly influenced by the exchange coupling and anisotropy of the magnetic core. By employing Green's function method in Hubbard operator representation, we give an analytical expression for local retarded Green's function of SMM and discussed its low-temperature transport properties. We find that the anisotropy term behaves as a magnetic field and the splitting behavior of exchange coupling is quite similar to the spin–orbit coupling. These splitting behaviors are explained by introducing inter-level or intra-level transitions, which account for the seven-peak splitting structure. Moreover, we find a Kondo dip at Fermi level under proper parameters. These Kondo peak splitting behaviors in SMM deepen our understanding to Kondo physics and should be observed in the future experiments. - Highlights: • We study Kondo peak splitting in single molecular magnets. • We study Kondo effect by Hubbard operator Green's function method. • We find Kondo peak splitting structures and a Kondo dip at Fermi level. • The exchange coupling and magnetic anisotropy induce fine splitting structure. • The splitting structures are explained by inter-level or intra-level transitions.

Measuring the Earth’s magnetic field dip angle using a smartphone-aided setup: a simple experiment for introductory physics laboratories

International Nuclear Information System (INIS)

Arabasi, Sameer; Al-Taani, Hussein

2017-01-01

Measurement of the Earth’s magnetic field dip angle is a widely used experiment in most introductory physics laboratories. In this paper we propose a smartphone-aided setup that takes advantage of the smartphone’s magnetometer sensor to measure the Earth’s magnetic field dip angle. This set-up will help students visualize the vector nature of the Earth’s magnetic field, especially high school and first year college students who are not quite experienced with vectors. This set-up is affordable and easy to use and could be easily produced by any high school or college physics instructor. (paper)

Measuring the Earth’s magnetic field dip angle using a smartphone-aided setup: a simple experiment for introductory physics laboratories

Science.gov (United States)

Arabasi, Sameer; Al-Taani, Hussein

2017-03-01

Measurement of the Earth’s magnetic field dip angle is a widely used experiment in most introductory physics laboratories. In this paper we propose a smartphone-aided setup that takes advantage of the smartphone’s magnetometer sensor to measure the Earth’s magnetic field dip angle. This set-up will help students visualize the vector nature of the Earth’s magnetic field, especially high school and first year college students who are not quite experienced with vectors. This set-up is affordable and easy to use and could be easily produced by any high school or college physics instructor.

First records of tool-set use for ant-dipping by Eastern chimpanzees (Pan troglodytes schweinfurthii) in the Kalinzu Forest Reserve, Uganda.

Science.gov (United States)

Hashimoto, Chie; Isaji, Mina; Koops, Kathelijne; Furuichi, Takeshi

2015-10-01

Chimpanzees at numerous study sites are known to prey on army ants by using a single wand to dip into the ant nest or column. However, in Goualougo (Republic of Congo) in Central Africa, chimpanzees use a different technique, use of a woody sapling to perforate the ant nest, then use of a herb stem as dipping tool to harvest the army ants. Use of a tool set has also been found in Guinea, West Africa: at Seringbara in the Nimba Mountains and at nearby Bossou. There are, however, no reports for chimpanzees in East Africa. We observed use of such a tool set in Kalinzu, Uganda, for the first time by Eastern chimpanzees. This behavior was observed among one group of chimpanzees at Kalinzu (S-group) but not among the adjacent group (M-group) with partly overlapping ranging areas despite the fact that the latter group has been under intensive observation since 1997. In Uganda, ant-dipping has not been observed in the northern three sites (Budongo, Semliki, and Kibale) but has been observed or seems to occur in the southern sites (Kalinzu and Bwindi), which suggests that ant-dipping was invented by and spread from the southern region after the northern and southern forest blocks became separated. Use of a tool-set by only one group at Kalinzu further suggests that this behavior was recently invented and has not yet spread to the other group via migrating females.

Statistical hot spot analysis of reactor cores

International Nuclear Information System (INIS)

Schaefer, H.

1974-05-01

This report is an introduction into statistical hot spot analysis. After the definition of the term 'hot spot' a statistical analysis is outlined. The mathematical method is presented, especially the formula concerning the probability of no hot spots in a reactor core is evaluated. A discussion with the boundary conditions of a statistical hot spot analysis is given (technological limits, nominal situation, uncertainties). The application of the hot spot analysis to the linear power of pellets and the temperature rise in cooling channels is demonstrated with respect to the test zone of KNK II. Basic values, such as probability of no hot spots, hot spot potential, expected hot spot diagram and cumulative distribution function of hot spots, are discussed. It is shown, that the risk of hot channels can be dispersed equally over all subassemblies by an adequate choice of the nominal temperature distribution in the core

Heat-pump performance: voltage dip/sag, under-voltage and over-voltage

Directory of Open Access Journals (Sweden)

William J.B. Heffernan

2014-12-01

Full Text Available Reverse cycle air-source heat-pumps are an increasingly significant load in New Zealand and in many other countries. This has raised concern over the impact wide-spread use of heat-pumps may have on the grid. The characteristics of the loads connected to the power system are changing because of heat-pumps. Their performance during under-voltage events such as voltage dips has the potential to compound the event and possibly cause voltage collapse. In this study, results from testing six heat-pumps are presented to assess their performance at various voltages and hence their impact on voltage stability.

On thermal vibration effects in diffusion model calculations of blocking dips

International Nuclear Information System (INIS)

Fuschini, E.; Ugozzoni, A.

1983-01-01

In the framework of the diffusion model, a method for calculating blocking dips is suggested that takes into account thermal vibrations of the crystal lattice. Results of calculations of the diffusion factor and the transverse energy distribution taking into accoUnt scattering of the channeled particles at thermal vibrations of lattice nuclei, are presented. Calculations are performed for α-particles with the energy of 2.12 MeV at 300 K scattered by Al crystal. It is shown that calculations performed according to the above method prove the necessity of taking into account effects of multiple scattering under blocking conditions

Jumlah bakteri Staphylococcus aureus dan skor California Mastitis Test (CMT pada susu kambing Peranakan Etawa akibat dipping ekstrak daun Babadotan (Ageratum conyzoides L.

Directory of Open Access Journals (Sweden)

Dwi Priono

2016-04-01

Full Text Available The aim of this research is to determine the effect of teat dipping of Ettawa crossbred goat using babadotan leaves (Ageratum conyzoides Linn. extract on the number of Staphylococcus aureusin milk. The udder inflammation degree also was determined using California Mastitis Test (CMT. The treatments were post milking teat dipping using antiseptic solutions containing 1%, 3%, and 5% of babadotan leaves extract (T1, T2 and T3, respectively. Milk samples were collected at before treatment (H0 and on the day 3, 6 and 9 day of the treatments (H3, H6 and H9, respectively. Commercially antiseptic povidone iodine was used as positive control (K+. Experimental research design was completely randomized design (CRD split plot types, with the different extract concentration as the main plot and the day of treatment as subplot. CMT scores was analyzed using Kruskal-Wallis test. The results showed that babadotan leaves extract 5% had the same effectiveness (p>0,05 with povidone iodine to reduce the number of Staphylococcus aureusin milk. All extract concentrations (1%, 3% and 5% had the same effectiveness (H>c0,05(3 to decrease the CMT scores by postmilking teat dip treatments for 9 days. Keywords:Teat dipping, Ageratum conyzoides (L., Staphylococcus aureus, CMT score

MIS hot electron devices for enhancement of surface reactivity by hot electrons

DEFF Research Database (Denmark)

Thomsen, Lasse Bjørchmar

A Metal-Insulator-Semiconductor (MIS) based device is developed for investigation of hot electron enhanced chemistry. A model of the device is presented explaining the key concepts of the functionality and the character- istics. The MIS hot electron emitter is fabricated using cleanroom technology...... and the process sequence is described. An Ultra High Vacuum (UHV) setup is modified to facilitate experiments with electron emission from the MIS hot electron emitters and hot electron chemistry. Simulations show the importance of keeping tunnel barrier roughness to an absolute minimum. The tunnel oxide...... to be an important energy loss center for the electrons tunneling through the oxide lowering the emission e±ciency of a factor of 10 for a 1 nm Ti layer thickness. Electron emission is observed under ambient pressure conditions and in up to 2 bars of Ar. 2 bar Ar decrease the emission current by an order...

Dimensional effects and scalability of Meta-Stable Dip (MSD) memory effect for 1T-DRAM SOI MOSFETs

Science.gov (United States)

Hubert, A.; Bawedin, M.; Cristoloveanu, S.; Ernst, T.

2009-12-01

The difficult scaling of bulk Dynamic Random Access Memories (DRAMs) has led to various concepts of capacitor-less single-transistor (1T) architectures based on SOI transistor floating-body effects. Amongst them, the Meta-Stable Dip RAM (MSDRAM), which is a double-gate Fully Depleted SOI transistor, exhibits attractive performances. The Meta-Stable Dip effect results from the reduced junction leakage current and the long carrier generation lifetime in thin silicon film transistors. In this study, various devices with different gate lengths, widths and silicon film thicknesses have been systematically explored, revealing the impact of transistor dimensions on the MSD effect. These experimental results are discussed and validated by two-dimensional numerical simulations. It is found that MSD is maintained for small dimensions even in standard SOI MOSFETs, although specific optimizations are expected to enhance MSDRAM performances.

Recent trend of administration on hot springs

Energy Technology Data Exchange (ETDEWEB)

Okubo, Shigeru [Environment Agency, Tokyo (Japan)

1989-01-01

The Environmental Agency exercises jurisdiction over Hot Spring Act, and plans to protect the source of the hot spring and to utilize it appropriately. From the aspect of utilization, hot springs are widely used as a means to remedy chronic diseases and tourist spots besides places for recuperation and repose. Statistics on Japanese hot springs showed that the number of hot spring spots and utilized-fountainhead increased in 1987, compared with the number in 1986. Considering the utilized-headspring, the number of naturally well-out springs has stabilized for 10 years while power-operated springs have increased. This is because the demand of hot springs has grown as the number of users has increased. Another reason is to keep the amount of hot water by setting up the power facility as the welled-out amount has decreased. Major point of recent administration on the hot spring is to permit excavation and utilization of hot springs. Designation of National hot spring health resorts started in 1954 in order to ensure the effective and original use of hot springs and to promote the public use of them, for the purpose of arranging the sound circumstances of hot springs. By 1988, 76 places were designated. 4 figs., 3 tabs.

2-D Deformation analysis of a half-space due to a long dip-slip fault ...

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

tic deformation in a uniform half-space due to long faults has been attempted by a number of researchers. Singh and Rani (1996) presented step- by-step progress made in the direction of crustal deformation modeling associated with strike-slip and dip-slip faulting in the earth. Cohen (1996) gave convenient formulas for ...

Computational Prediction of Hot Spot Residues

Science.gov (United States)

Morrow, John Kenneth; Zhang, Shuxing

2013-01-01

Most biological processes involve multiple proteins interacting with each other. It has been recently discovered that certain residues in these protein-protein interactions, which are called hot spots, contribute more significantly to binding affinity than others. Hot spot residues have unique and diverse energetic properties that make them challenging yet important targets in the modulation of protein-protein complexes. Design of therapeutic agents that interact with hot spot residues has proven to be a valid methodology in disrupting unwanted protein-protein interactions. Using biological methods to determine which residues are hot spots can be costly and time consuming. Recent advances in computational approaches to predict hot spots have incorporated a myriad of features, and have shown increasing predictive successes. Here we review the state of knowledge around protein-protein interactions, hot spots, and give an overview of multiple in silico prediction techniques of hot spot residues. PMID:22316154

Synthesis of LSM films deposited by dip-coating on YSZ substrate; Sintese de filmes de LSM depositados por dip-coating em substratos de YSZ

Energy Technology Data Exchange (ETDEWEB)

Conceicao, Leandro da; Souza, Mariana M.V.M., E-mail: mmattos@eq.ufrj.b [Universidade Federal do Rio de Janeiro (EQ/UFRJ), RJ (Brazil). Escola de Quimica; Ribeiro, Nielson F.P. [Coordenacao dos Programas de Pos-graduacao de Engenharia (PEQ/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Quimica. Nucleo de Catalise

2010-07-01

The dip-coating process was used to deposit films of La{sub 0.7}Sr{sub 0.}3MnO{sub 3} (LSM) used as cathode in solid oxide fuel cells (SOFC). In this study we evaluated the relationship between the deposition parameters such as speed of withdrawal and number of deposited layers of LSM film on a substrate of 8% YSZ commercial, and structural properties, such as thickness and formation of cracks. The structure and morphology of the films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). With parameters set the film had good adhesion to the substrate with a thickness around 10 {mu}m, showing possible adherence problems when more than one layer is deposited on the substrate. (author)

Modeling and inversion of PS-wave moveout asymmetry for tilted TI media: Part 2: Dipping TTI layer

Digital Repository Service at National Institute of Oceanography (India)

Dewangan, P.; Tsvankin, I.

Dipping transversely isotropic layers with a tilted symmetry axis (TTI media) cause serious imaging problems in fold-and-thrust belts and near salt domes. The modified PP + PS = SS method introduced in Part 1 is applied to the inversion...

Mechanical properties of chemically bonded sand core materials dipped in sol-gel coating impregnated with filter

DEFF Research Database (Denmark)

Nwaogu, Ugochukwu Chibuzoh; Tiedje, Niels Skat

2012-01-01

A novel sol-gel coating impregnated with filter dust was applied on chemically bonded sand core materials by dipping. After curing, the strengths of the core materials were measured under uniaxial loading using a new strength testing machine (STM). The STM presents the loading history as a force-...... of the chemically bonded sand core materials, a combination of flexural and compression tests is suggested for improving the casting quality. © 2012 W. S. Maney & Son Ltd.......A novel sol-gel coating impregnated with filter dust was applied on chemically bonded sand core materials by dipping. After curing, the strengths of the core materials were measured under uniaxial loading using a new strength testing machine (STM). The STM presents the loading history as a force...... the strengths were increased under compression. The mode of fracture of the chemically bonded sand core materials was observed to be intergranular through the binder. The stiffness of the chemically bonded sand core materials was determined. For better understanding of the mechanical properties...

Studies on acetone sensing characteristics of ZnO thin film prepared by sol–gel dip coating

Energy Technology Data Exchange (ETDEWEB)

Muthukrishnan, Karthika; Vanaraja, Manoj [School of Electrical & Electronics Engineering, SASTRA University, Thanjavur, 613401 (India); Boomadevi, Shanmugam [Department of Physics, National Institute of Technology, Tiruchirappalli, 620015 (India); Karn, Rakesh Kumar [School of Electrical & Electronics Engineering, SASTRA University, Thanjavur, 613401 (India); Singh, Vijay [Department of Chemical Engineering, Konkuk University, Seoul, 143-701 (Korea, Republic of); Singh, Pramod K. [Solar Energy Institute, Ege University, Bornova, 35100, Izmir (Turkey); Material Research Laboratory, School of Basic Sciences and Research, Sharda University, Greater Noida, 201310, U. P. (India); Pandiyan, Krishnamoorthy, E-mail: krishpandiyan@ece.sastra.edu [School of Electrical & Electronics Engineering, SASTRA University, Thanjavur, 613401 (India)

2016-07-15

Acetone sensing characteristics of Zinc Oxide thin films prepared by dip coating method are discussed in this paper. The sol for dip coating was synthesized using Zinc nitrate hexahydrate (Zn (NO{sub 3}){sub 2}. 6H{sub 2}O) and organic polymer sodium carboxy methyl cellulose (Na-CMC) as a starting material. Crystallinity and crystallite size of the prepared thin film was characterised by X-ray diffraction (XRD). Morphology was studied using field emission scanning electron microscopy (FESEM). The gas sensing characteristics was studied using chemiresistive method, by exposing the film to various concentrations of acetone at room temperature. Further, for comparative study ethanol and acetaldehyde has also been tested. Gas sensing parameters such us response, selectivity, lowest detection limit, response/recovery time of the thin film towards acetone were also reported. - Highlights: • ZnO has successfully synthesized using cheap and ease method. • Detail characterization have carried out and explained. • Sensing behaviour has been studied. • Acetone sensor has been fabricated.

Hot Spots and Hot Moments of Nitrogen in a Riparian Corridor

Science.gov (United States)

Dwivedi, Dipankar; Arora, Bhavna; Steefel, Carl I.; Dafflon, Baptiste; Versteeg, Roelof

2018-01-01

We use 3-D high-resolution reactive transport modeling to investigate whether the spatial distribution of organic-carbon-rich and chemically reduced sediments located in the riparian zone and temporal variability in groundwater flow direction impact the formation and distribution of nitrogen hot spots (regions that exhibit higher reaction rates when compared to other locations nearby) and hot moments (times that exhibit high reaction rates as compared to longer intervening time periods) within the Rifle floodplain in Colorado. Groundwater flows primarily toward the Colorado River from the floodplain but changes direction at times of high river stage. The result is that oxic river water infiltrates the Rifle floodplain during these relatively short-term events. Simulation results indicate that episodic rainfall in the summer season leads to the formation of nitrogen hot moments associated with Colorado River rise and resulting river infiltration into the floodplain. The results further demonstrate that the naturally reduced zones (NRZs) present in sediments of the Rifle floodplain have a higher potential for nitrate removal, approximately 70% greater than non-NRZs for typical hydrological conditions. During river water infiltration, nitrate reduction capacity remains the same within the NRZs, however, these conditions impact non-NRZs to a greater extent (approximately 95% less nitrate removal). Model simulations indicate chemolithoautotrophs are primarily responsible for the removal of nitrate in the Rifle floodplain. These nitrogen hot spots and hot moments are sustained by microbial respiration and the chemolithoautotrophic oxidation of reduced minerals in the riparian zone.

Hot Spot Removal System: System description

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

Hazardous wastes contaminated with radionuclides, chemicals, and explosives exist across the Department of Energy complex and need to be remediated due to environmental concerns. Currently, an opportunity is being developed to dramatically reduce remediation costs and to assist in the acceleration of schedules associated with these wastes by deploying a Hot Spot Removal System. Removing the hot spot from the waste site will remove risk driver(s) and enable another, more cost effective process/option/remedial alternative (i.e., capping) to be applied to the remainder of the site. The Hot Spot Removal System consists of a suite of technologies that will be utilized to locate and remove source terms. Components of the system can also be used in a variety of other cleanup activities. This Hot Spot Removal System Description document presents technologies that were considered for possible inclusion in the Hot Spot Removal System, technologies made available to the Hot Spot Removal System, industrial interest in the Hot Spot Removal System`s subsystems, the schedule required for the Hot Spot Removal System, the evaluation of the relevant technologies, and the recommendations for equipment and technologies as stated in the Plan section.

Hot Spot Removal System: System description

International Nuclear Information System (INIS)

1997-09-01

Hazardous wastes contaminated with radionuclides, chemicals, and explosives exist across the Department of Energy complex and need to be remediated due to environmental concerns. Currently, an opportunity is being developed to dramatically reduce remediation costs and to assist in the acceleration of schedules associated with these wastes by deploying a Hot Spot Removal System. Removing the hot spot from the waste site will remove risk driver(s) and enable another, more cost effective process/option/remedial alternative (i.e., capping) to be applied to the remainder of the site. The Hot Spot Removal System consists of a suite of technologies that will be utilized to locate and remove source terms. Components of the system can also be used in a variety of other cleanup activities. This Hot Spot Removal System Description document presents technologies that were considered for possible inclusion in the Hot Spot Removal System, technologies made available to the Hot Spot Removal System, industrial interest in the Hot Spot Removal System''s subsystems, the schedule required for the Hot Spot Removal System, the evaluation of the relevant technologies, and the recommendations for equipment and technologies as stated in the Plan section

Charge transfer and partial pinning at the contacts as the origin of a double dip in the transfer characteristics of graphene-based field-effect transistors

International Nuclear Information System (INIS)

Di Bartolomeo, Antonio; Giubileo, Filippo; Santandrea, Salvatore; Romeo, Francesco; Citro, Roberta; Schroeder, Thomas; Lupina, Grzegorz

2011-01-01

We discuss the origin of an additional dip other than the charge neutrality point observed in the transfer characteristics of graphene-based field-effect transistors with a Si/SiO 2 substrate used as the back-gate. The double dip is proved to arise from charge transfer between the graphene and the metal electrodes, while charge storage at the graphene/SiO 2 interface can make it more evident. Considering a different Fermi energy from the neutrality point along the channel and partial charge pinning at the contacts, we propose a model which explains all the features observed in the gate voltage loops. We finally show that the double dip enhanced hysteresis in the transfer characteristics can be exploited to realize graphene-based memory devices.

The Distinction of Hot Herbal Compress, Hot Compress, and Topical Diclofenac as Myofascial Pain Syndrome Treatment.

Science.gov (United States)

Boonruab, Jurairat; Nimpitakpong, Netraya; Damjuti, Watchara

2018-01-01

This randomized controlled trial aimed to investigate the distinctness after treatment among hot herbal compress, hot compress, and topical diclofenac. The registrants were equally divided into groups and received the different treatments including hot herbal compress, hot compress, and topical diclofenac group, which served as the control group. After treatment courses, Visual Analog Scale and 36-Item Short Form Health survey were, respectively, used to establish the level of pain intensity and quality of life. In addition, cervical range of motion and pressure pain threshold were also examined to identify the motional effects. All treatments showed significantly decreased level of pain intensity and increased cervical range of motion, while the intervention groups exhibited extraordinary capability compared with the topical diclofenac group in pressure pain threshold and quality of life. In summary, hot herbal compress holds promise to be an efficacious treatment parallel to hot compress and topical diclofenac.

Hot particles

International Nuclear Information System (INIS)

Merwin, S.E.; Moeller, M.P.

1989-01-01

Nuclear Regulatory Commission (NRC) licensees are required to assess the dose to skin from a hot particle contamination event at a depth of skin of7mg/cm 2 over an area of 1 cm 2 and compare the value to the current dose limit for the skin. Although the resulting number is interesting from a comparative standpoint and can be used to predict local skin reactions, comparison of the number to existing limits based on uniform exposures is inappropriate. Most incidents that can be classified as overexposures based on this interpretation of dose actually have no effect on the health of the worker. As a result, resources are expended to reduce the likelihood that an overexposure event will occur when they could be directed toward eliminating the cause of the problem or enhancing existing programs such as contamination control. Furthermore, from a risk standpoint, this practice is not ALARA because some workers receive whole body doses in order to minimize the occurrence of hot particle skin contaminations. In this paper the authors suggest an alternative approach to controlling hot particle exposures

Modeled long-term changes of DIN:DIP ratio in the Changjiang River in relation to Chl-α and DO concentrations in adjacent estuary

Science.gov (United States)

Wang, Jianing; Yan, Weijin; Chen, Nengwang; Li, Xinyan; Liu, Lusan

2015-12-01

In the past four decades (1970-2013), nitrogen and phosphorous inputs to the Changjiang River basin, mainly from human activities, have increased 3-fold and 306-fold, respectively. The riverine nutrient fluxes to the estuary have also grown exponentially. Dissolved inorganic nitrogen (DIN) and dissolved inorganic phosphorous (DIP) fluxes of the Changjiang River increased by 338% and 574% during 1970-2013 period, and red tides and benthic hypoxia have been observed in the outflow region of the Changjiang River in the East China Sea (ECS). We assumed that time series changes in the DIN:DIP ratio from the Changjiang River could have a significant impact on Chlorophyll-α (Chl-α) concentration in the surface sea water and dissolved oxygen (DO) concentration in the bottom sea water of the Changjiang estuary. Our study showed that the DIN:DIP ratio from the Changjiang River increased from 76 to 384 between 1970 and 1985, and decreased from 255 to 149 between 1986 and 2013. The observed Chl-α concentration increased by 146% from 1992 to 2010 in the Changjiang estuary, and was negatively related to the DIN:DIP ratio in 1992-2010. Bottom sea water DO concentration decreased by 24.6% during 1992-2010 and a "low oxygen zone" (122°∼123°E, 32°∼33°N) was observed during summer since 1999. The anthropogenically enhanced nutrient inputs dominated river DIN and DIP fluxes and influenced Chl-α concentrations as well as bottom DO concentrations in the estuary. Scenarios emphasizing global collaboration and proactive environmental problem-solving may result in reductions in the river nutrient exports and in Chl-α and DO concentration in the Changjiang estuary by 2050.

Improved H-κ Method by Harmonic Analysis on Ps and Crustal Multiples in Receiver Functions with respect to Dipping Moho and Crustal Anisotropy

Science.gov (United States)

Li, J.; Song, X.; Wang, P.; Zhu, L.

2017-12-01

The H-κ method (Zhu and Kanamori, 2000) has been widely used to estimate the crustal thickness and Vp/Vs ratio with receiver functions. However, in regions where the crustal structure is complicated, the method may produce uncertain or even unrealistic results, arising particularly from dipping Moho and/or crustal anisotropy. Here, we propose an improved H-κ method, which corrects for these effects first before stacking. The effect of dipping Moho and crustal anisotropy on Ps receiver function has been well studied, but not as much on crustal multiples (PpPs and PpSs+PsPs). Synthetic tests show that the effect of crustal anisotropy on the multiples are similar to Ps, while the effect of dipping Moho on the multiples is 5 times that on Ps (same cosine trend but 5 times in time shift). A Harmonic Analysis (HA) method for dipping/anisotropy was developed by Wang et al. (2017) for crustal Ps receiver functions to extract parameters of dipping Moho and crustal azimuthal anisotropy. In real data, the crustal multiples are much more complicated than the Ps. Therefore, we use the HA method (Wang et al., 2017), but apply separately to Ps and the multiples. It shows that although complicated, the trend of multiples can still be reasonably well represented by the HA. We then perform separate azimuthal corrections for Ps and the multiples and stack to obtain a combined receiver function. Lastly, the traditional H-κ procedure is applied to the stacked receiver function. We apply the improved H-κ method on 40 CNDSN (Chinese National Digital Seismic Network) stations distributed in a variety of geological setting across the Chinese continent. The results show apparent improvement compared to the traditional H-κ method, with clearer traces of multiples and stronger stacking energy in the grid search, as well as more reliable H-κ values.

Hot-Film and Hot-Wire Anemometry for a Boundary Layer Active Flow Control Test

Science.gov (United States)

Lenahan, Keven C.; Schatzman, David M.; Wilson, Jacob Samuel

2013-01-01

Unsteady active flow control (AFC) has been used experimentally for many years to minimize bluff-body drag. This technology could significantly improve performance of rotorcraft by cleaning up flow separation. It is important, then, that new actuator technologies be studied for application to future vehicles. A boundary layer wind tunnel was constructed with a 1ft-x-3ft test section and unsteady measurement instrumentation to study how AFC manipulates the boundary layer to overcome adverse pressure gradients and flow separation. This unsteady flow control research requires unsteady measurement methods. In order to measure the boundary layer characteristics, both hot-wire and hot-film Constant Temperature Anemometry is used. A hot-wire probe is mounted in the flow to measure velocity while a hot-film array lays on the test surface to measure skin friction. Hot-film sensors are connected to an anemometer, a Wheatstone bridge circuit with an output that corresponds to the dynamic flow response. From this output, the time varying flow field, turbulence, and flow reversal can be characterized. Tuning the anemometers requires a fan test on the hot-film sensors to adjust each output. This is a delicate process as several variables drastically affect the data, including control resistance, signal input, trim, and gain settings.

Polymer nanocomposite patterning by dip-pen nanolithography

International Nuclear Information System (INIS)

Kandemir, Ayse Cagil; Ma, Huan; Reiser, Alain; Spolenak, Ralph; Erdem, Derya

2016-01-01

The ultimate aim of this study is to construct polymer nanocomposite patterns by dip-pen nanolithography (DPN). Recent investigations have revealed the effect of the amount of ink (Laplace pressure) on the mechanism of liquid ink writing. In this study it is shown that not only the amount of ink, but also physisorption and surface diffusion are relevant. After a few writing steps, physisorption and surface diffusion outweigh the influence of the amount of ink, allowing consistent patterning governed by dwell times and writing speeds. Polymer matrices can be utilized as a delivery medium to deposit functional particles. DPN patterning of polymer nanocomposites allows for local tuning of the functionality and mechanical strength of the written patterns in high resolution, with the benefit of pattern flexibility. Typically polymer matrices with volatile components are used as a delivery medium for nanoparticle deposition, with subsequent removal of loosely bound matrix material by heating or oxygen plasma. In our study, nanocomposite patterns were constructed, and the differences between polymer and nanocomposite patterning were investigated. Cross-sectional SEM and TEM analysis confirmed that nanoparticles can be deposited with the liquid-polymer ink and are evenly distributed in the polymer matrix. (paper)

SHOSPA-MOD, Hot Spot Factors for Fuel and Clad, Hot Channel Factors

International Nuclear Information System (INIS)

Amendola, A.

1982-01-01

1 - Nature of the physical problem solved: SHOSPA evaluates the hot spot factors for fuel and cladding as well as the hot channel factor as a function of the confidence level. Moreover, it evaluates the probability on n hot subassemblies. The code has been developed with emphasis on sodium cooled fast reactors, but it is applicable to any type of reactors constituted of bundled fuel rods with single phase coolant. An option for plotting is available in this version. 2 - Restrictions on the complexity of the problem: This code is applicable to any type of reactors constituted of fuel rods with single phase coolant

Dip-Pen Nanolithography on (Bio)Reactive Monolayer and Block-Copolymer Platforms: Deposition of Lines of Single Macromolecules

NARCIS (Netherlands)

Salazar, Ramon B.; Shovsky, A.; Schönherr, Holger; Vancso, Gyula J.

2006-01-01

The application of atomic force microscopy (AFM) tip-mediated molecular transfer (dip-pen nanolithography or DPN) to fabricate nanopatterned (bio)reactive platforms based on dendrimers on reactive self-assembled monolayer (SAM) and polymer thin films is discussed. The transfer of high-molar-mass

Effects of modified atmosphere packing and honey dip treatments on quality maintenance of minimally processed grape cv. Razaki (V. vinifera L.) during cold storage.

Science.gov (United States)

Sabır, Ali; Sabır, Ferhan K; Kara, Zeki

2011-06-01

Increasing pressure in food conservation sector to replace chemical applications has urged researchers to focus on studying new strategies of extending the postharvest life of produces. In such efforts, numerous materials have been tested for their effectiveness as well as suitability in organic consumption. In this study, effects of modified atmosphere packing (MAP) and honey solution dip on maintenance of quality of minimally processed table grape cv. Razaki were investigated. During the storage at 0 °C with relative humidity of 90%, MAP, honey dip, and their combined applications significantly retarded the weight loss of berries that retained about 2 mm of cap stem. Soluble solid contents of all berries slightly increased, while their acid amounts decreased, resulting in consecutive rises of maturity index. With respect to the sensory score, calculated as mean of ten panelists, honey treatment alone was ranked the highest while control berries had significantly lower value. Overall, MAP, honey solution dip or their combination significantly maintained the general quality of minimally processed grape by delaying quality loss and berry decay. Therefore, honey solution dip yielded promising results to use as an edible organic coating barrier to moisture and resist to water vapor diffusion during the cold storage, offering a good adherence to berry surface.

Absorption dips at low x-ray energies in Cygnus X-1

International Nuclear Information System (INIS)

Murdin, P.

1976-01-01

Three more looks with the Copernicus satellite at Cygnus X-1 have produced four more examples of absorption dips, decreases in the 2 to 7 keV flux from Cygnus X-1 with an increase of spectral hardness consistent with photoelectric absorption (Mason et al 1974). The nine now seen, including one by OSO-7 (Li and Clark 1974), are listed in Table 1. Their phase in the spectroscopic binary HD 226868 is also listed, calculated from a newer ephemeris than that in Mason et al (1974), adding the radial velocities by Bolton (1975) and unpublished RGO radial velocities from the 1975 season. (These elements do not differ significantly from Bolton's

Application of Cyclone to Removal of Hot Particulate in Hot Cell

International Nuclear Information System (INIS)

Kim, Gye Nam; Lee, Sung Yeol; Won, Hui Jun; Jung, Chong Hun; Oh, Won Zin

2005-01-01

The size and main ingredient of hot particulate generated during the nuclide experiment in hot cells of nuclear facilities were 0.5300 μm and UO 2 . A cyclone filter equipment which consists of a cyclone and Bag/HEPA filter was devised to remove hot particulate generated during the nuclide experiment in hot cells of nuclear facilities. The experimental conditions to maximize the collection efficiency of hot particulate were suggested through experiments done with the cyclone filter equipment. With the large size of simulated particulate, the collection efficiency of the particulate was high. When the size of simulated particulate was more than 5 μm, the collection efficiency of the particulate was more than 80% and when the size of simulated particulate was less than 1.0 μm, the collection efficiency decreased by less than. If the inflow velocity of simulated particulate was increased, the collection efficiency of the particulate was also increased. When the inflow velocity of simulated particulate was more than 12 m/sec, the collection efficiency was higher than , but after 17 m/sec inflow velocity, no change observed. The collection efficiency of the simulated particulate can be enhanced with the length of vortex finder inside the chamber. With the length of vortex finder, 7.2 cm, the observed collection efficiency of the particulate was the maximum. Moreover, when the sub-cone was attached under the cyclone, the collection efficiency of cyclone increased 2%. It was found that effect by attachment of sub-cone was not serious.

Caracterització mineralògica dels materials dels dipòsits de tungstè de Mittersill i Morille per el seu processament

OpenAIRE

Call Espinalt, Joan

2016-01-01

La mineralogia dels dipòsits de tungstè de Mittersill (Àustria) i Morille (Espanya) han estat caracteritzats. L’objectiu d’aquest treball és caracteritzar dipòsits de tungstè per que es pugui desenvolupar una metodologia per tal d’assolir una millora substancial en l’alliberament del tungstè a partir de les menes estudiades. Per aconseguir-ho buscarem quina és la mida de màxim alliberament del mineral. La composició química ha estat obtinguda per mitjà d’una Espectrometria de Masses per Plasm...

Dipping of Eggs, Use of Low Temperature and Aeration to Improve Fruit Fly Bactrocera Carambolae (Drew and Hancock) Mass Rearing in Sterile Insect Technique Programme

International Nuclear Information System (INIS)

Nasution, Indah Arastuti; Achmad Nasroh Kuswadi

2004-01-01

In the Sterile Insect Technique (SIT) programme a large number of homogenous age of pupae should be produced to be sterilized and released into the field. A methodology to preserve eggs which at the same time delay the egg hatch is needed in the production of a large number of pupae with homogenous age. The study on method of preserving fruit fly eggs the effect of dipping, low temperature, on the viability of eggs, the quality of larvae hatched from the eggs, and the quality of pupae produced were observed. Viability of eggs were observed as percent of egg hatch, quality of larvae as number of pupae produced from 0.5 ml of eggs when reared on artificial diet, and quality of pupae as percent of the flies number emerged and flew from the pupae. In room temperature (26 o C) dipping did not preserve fruit fly eggs and aeration did not improve the preservation. Although after one day dipping the viability of eggs only decreased from 90 % (control) to 80.5 %, (without aeration) and 81.5 % (with aeration) it decreased the number of pupae been produced from 1447 pupae (control) to 382 pupae (without aeration) and 616 pupae (with aeration). Low temperature successfully preserved the egg up to 24 hours. After 24 hour dipping in low temperature (16 o C) the viability of eggs were decreased up to 84.75 % (without aeration) and able to produce 1104 pupae. Aeration during dipping in low temperature did not improve the preservation. (author)

Ionospheric hot spot at high latitudes

International Nuclear Information System (INIS)

Schunk, R.W.; Sojka, J.J.

1982-01-01

A hot spot (or spots) can occur in the high-latitude ionosphere depending on the plasma convection pattern. The hot spot corresponds to a small magnetic local time-magnetic latitude region of elevated ion temperatures located near the dusk and/or dawn meridians. For asymmetric convection electric field patterns, with enhanced flow in either the dusk or dawn sector of the polar cap, a single hot spot should occur in association with the strong convection cell. However, on geomagnetically disturbed days, two strong convection cells can occur, and hence, two hot spots should exist. The hot spot should be detectable when the electric field in the strong convection cell exceeds about 40 mV m -1 . For electric fields of the order of 100 mV m -1 in the convection cell, the ion temperature in the hot spot is greatest at low altitudes, reaching 4000 0 K at 160 km, and decreases with altitude in the F-region. An ionospheric hot spot (or spots) can be expected at all seasons and for a wide range of solar cycle conditions

Menopausal Hot Flashes and White Matter Hyperintensities

Science.gov (United States)

Thurston, Rebecca C.; Aizenstein, Howard J.; Derby, Carol A.; Sejdić, Ervin; Maki, Pauline M.

2015-01-01

Objective Hot flashes are the classic menopausal symptom. Emerging data links hot flashes to cardiovascular disease (CVD) risk, yet how hot flashes are related to brain health is poorly understood. We examined the relationship between hot flashes - measured via physiologic monitor and self-report - and white matter hyperintensities (WMH) among midlife women. Methods Twenty midlife women ages 40-60 without clinical CVD, with their uterus and both ovaries, and not taking hormone therapy were recruited. Women underwent 24 hours of ambulatory physiologic and diary hot flash monitoring to quantify hot flashes; magnetic resonance imaging to assess WMH burden; 72 hours of actigraphy and questionnaires to quantify sleep; and a blood draw, questionnaires, and physical measures to quantify demographics and CVD risk factors. Test of a priori hypotheses regarding relations between physiologically-monitored and self-reported wake and sleep hot flashes and WMH were conducted in linear regression models. Results More physiologically-monitored hot flashes during sleep were associated with greater WMH, controlling for age, race, and body mass index [beta(standard error)=.0002 (.0001), p=.03]. Findings persisted controlling for sleep characteristics and additional CVD risk factors. No relations were observed for self-reported hot flashes. Conclusions More physiologically-monitored hot flashes during sleep were associated with greater WMH burden among midlife women free of clinical CVD. Results suggest that relations between hot flashes and CVD risk observed in the periphery may extend to the brain. Future work should consider the unique role of sleep hot flashes in brain health. PMID:26057822

Determination of solid-liquid partition coefficients (K{sub d}) for diazinon, propetamphos and cis-permethrin: implications for sheep dip disposal

Energy Technology Data Exchange (ETDEWEB)

Cooke, Cindy M.; Shaw, George; Lester, John N.; Collins, Chris D

2004-08-15

Two groups of chemicals are currently licensed for use in sheep dip products in the UK. These are organophosphate (OP) insecticides and synthetic pyrethroid (SP) insecticides. SPs are deemed to be less toxic to human health than OPs, although they are approximately 100 times more toxic to some elements of the aquatic environment. Three insecticides were selected for experimental investigation: diazinon, propetamphos (OPs) and cis-permethrin (SP), representative of the active ingredients used in sheep dip formulations, with additional uses in insect control in crops, and for domestic control of flies, mosquitoes, cockroaches, lice, ticks and spiders. The UK Government has recently reviewed agricultural practices relating to the disposal of used sheep dip, because the constituent insecticides are frequently detected in UK watercourses and the presence of these compounds is a severe hazard to the aquatic environment. Standard batch sorption experiments were carried out to investigate insecticide partitioning from water to soil, and the relationship between sorption and soil organic carbon content is discussed. Sorption isotherms and K{sub d} values showed that cis-permethrin adsorption was fastest on all five soils investigated, exhibiting the greatest total partitioning to the soil phase (83.8-94.8%) and high resistance to desorption. In comparison, the OP insecticides exhibited moderately strong soil adsorption as evidenced by their K{sub d} coefficients (diazinon K{sub d} 12-35 and propetamphos K{sub d} 9-60), with low sorption reversibility (<15%). Calculation of a hydrological retardation factor in a scenario representative of a typical UK environment suggested that SP insecticides such as cis-permethrin will not migrate in the soil profile due to their virtual immobility and strong soil retention, and thus waste sheep dip disposal to agricultural land should not pose a risk to aquatic life if applied with appropriate controls.

State reference design and saturated control of doubly-fed induction generators under voltage dips

Science.gov (United States)

Tilli, Andrea; Conficoni, Christian; Hashemi, Ahmad

2017-04-01

In this paper, the stator/rotor currents control problem of doubly-fed induction generator under faulty line voltage is carried out. Common grid faults cause a steep decline in the line voltage profile, commonly denoted as voltage dip. This point is critical for such kind of machines, having their stator windings directly connected to the grid. In this respect, solid methodological nonlinear control theory arguments are exploited and applied to design a novel controller, whose main goal is to improve the system behaviour during voltage dips, endowing it with low voltage ride through capability, a fundamental feature required by modern Grid Codes. The proposed solution exploits both feedforward and feedback actions. The feedforward part relies on suitable reference trajectories for the system internal dynamics, which are designed to prevent large oscillations in the rotor currents and command voltages, excited by line perturbations. The feedback part uses state measurements and is designed according to Linear Matrix Inequalities (LMI) based saturated control techniques to further reduce oscillations, while explicitly accounting for the system constraints. Numerical simulations verify the benefits of the internal dynamics trajectory planning, and the saturated state feedback action, in crucially improving the Doubly-Fed Induction Machine response under severe grid faults.

Hot tearing studies in AA5182

Science.gov (United States)

van Haaften, W. M.; Kool, W. H.; Katgerman, L.

2002-10-01

One of the major problems during direct chill (DC) casting is hot tearing. These tears initiate during solidification of the alloy and may run through the entire ingot. To study the hot tearing mechanism, tensile tests were carried out in semisolid state and at low strain rates, and crack propagation was studied in situ by scanning electron microscopy (SEM). These experimentally induced cracks were compared with hot tears developed in an AA5182 ingot during a casting trial in an industrial research facility. Similarities in the microstructure of the tensile test specimens and the hot tears indicate that hot tearing can be simulated by performing tensile tests at semisolid temperatures. The experimental data were compared with existing hot tearing models and it was concluded that the latter are restricted to relatively high liquid fractions because they do not take into account the existence of solid bridges in the crack.

Do scientists trace hot topics?

Science.gov (United States)

Wei, Tian; Li, Menghui; Wu, Chensheng; Yan, Xiao-Yong; Fan, Ying; Di, Zengru; Wu, Jinshan

2013-01-01

Do scientists follow hot topics in their scientific investigations? In this paper, by performing analysis to papers published in the American Physical Society (APS) Physical Review journals, it is found that papers are more likely to be attracted by hot fields, where the hotness of a field is measured by the number of papers belonging to the field. This indicates that scientists generally do follow hot topics. However, there are qualitative differences among scientists from various countries, among research works regarding different number of authors, different number of affiliations and different number of references. These observations could be valuable for policy makers when deciding research funding and also for individual researchers when searching for scientific projects.

EXOSAT observations of V471 Tauri - a 9.25 minute white dwarf pulsation and orbital phase dependent X-ray dips

International Nuclear Information System (INIS)

Jensen, K.A.; Swank, J.H.; Petre, P.; Guinan, E.F.; Sion, E.M.; Navy, E. O. Hulburt Center for Space Research, Washington, DC; Villanova Univ., PA)

1986-01-01

New results obtained from a 28 hr continuous observation of V471 Tauri with the EXOSAT satellite are reported. The detection of soft X-ray fluxes from both the white dwarf and the K dwarf, the discovery of a 9.25 minute pulsation from the white dwarf, and the discovery of orbital phase-related soft X-ray dips are discussed. The dips may be correlated with the triangular Lagrangian points of the binary orbit. The X-ray flux from the white dwarf is consistent with thermal models for a white dwarf photosphere with T(eff) of about 35,000 K, log g = 8.0-8.5, and log N(H) = 18.65 + or - 0.2. 25 references

'Hot' cognition in major depressive disorder

DEFF Research Database (Denmark)

Miskowiak, Kamilla W; Carvalho, Andre F

2014-01-01

Major depressive disorder (MDD) is associated with significant cognitive dysfunction in both 'hot' (i.e. emotion-laden) and 'cold' (non-emotional) domains. Here we review evidence pertaining to 'hot' cognitive changes in MDD. This systematic review searched the PubMed and PsycInfo computerized......-limbic network with hyper-activity in limbic and ventral prefrontal regions paired with hypo-activity of dorsal prefrontal regions subserve these abnormalities. A cross-talk of 'hot' and 'cold' cognition disturbances in MDD occurs. Disturbances in 'hot cognition' may also contribute to the perpetuation......' cognition deficits in healthy relatives of patients with MDD. Taken together, these findings suggest that abnormalities in 'hot' cognition may constitute a candidate neurocognitive endophenotype for depression....

Personality disorders in substance abusers: Validation of the DIP-Q through principal components factor analysis and canonical correlation analysis

Directory of Open Access Journals (Sweden)

Hesse Morten

2005-05-01

Full Text Available Abstract Background Personality disorders are common in substance abusers. Self-report questionnaires that can aid in the assessment of personality disorders are commonly used in assessment, but are rarely validated. Methods The Danish DIP-Q as a measure of co-morbid personality disorders in substance abusers was validated through principal components factor analysis and canonical correlation analysis. A 4 components structure was constructed based on 238 protocols, representing antagonism, neuroticism, introversion and conscientiousness. The structure was compared with (a a 4-factor solution from the DIP-Q in a sample of Swedish drug and alcohol abusers (N = 133, and (b a consensus 4-components solution based on a meta-analysis of published correlation matrices of dimensional personality disorder scales. Results It was found that the 4-factor model of personality was congruent across the Danish and Swedish samples, and showed good congruence with the consensus model. A canonical correlation analysis was conducted on a subset of the Danish sample with staff ratings of pathology. Three factors that correlated highly between the two variable sets were found. These variables were highly similar to the three first factors from the principal components analysis, antagonism, neuroticism and introversion. Conclusion The findings support the validity of the DIP-Q as a measure of DSM-IV personality disorders in substance abusers.

A review on hot tearing of magnesium alloys

Directory of Open Access Journals (Sweden)

Jiangfeng Song

2016-09-01

Full Text Available Hot tearing is often a major casting defect in magnesium alloys and has a significant impact on the quality of their casting products. Hot tearing of magnesium alloys is a complex solidification phenomenon which is still not fully understood, it is of great importance to investigate the hot tearing behaviour of magnesium alloys. This review attempts to summarize the investigations on hot tearing of magnesium alloys over the past decades. The hot tearing criteria including recently developed Kou's criterion are summarized and compared. The numeric simulation and assessing methods of hot tearing, factors influencing hot tearing, and hot tearing susceptibility (HTS of magnesium alloys are discussed.

Ninth international symposium on hot atom chemistry. Abstracts

International Nuclear Information System (INIS)

1977-01-01

Abstracts of the papers presented at the Symposium are compiled. The topics considered were chemical dynamics of high energy reactions, hot atom chemistry in organic compounds of tritium, nitrogen, oxygen, and halogens, theory and chemical dynamics of hot atom reactions as determined by beam studies, solid state reactions of recoil atoms and implanted ions, hot atom chemistry in energy-related research, hot atom chemistry in inorganic compounds of oxygen and tritium, hot positronium chemistry, applied hot atom chemistry in labelling, chemical effects of radioactive decay, decay-induced reactions and excitation labelling, physical methods in hot atom chemistry, and hot atom reactions in radiation and stratospheric chemistry

The Effect of Coriolis Force on the Formation of Dip on the Free Surface of Water Draining from a Tank

International Nuclear Information System (INIS)

Jo, Jong Chull; Kang, Dong Gu; Kim, Hho Jhung; Roh, Kyung Wan; Yune, Young Gill

2007-01-01

For the case of RWT (refueling water tank) connecting to the ECC (emergency core cooling) line, it can be surmised that there is a possibility of ECC pump failure due to air ingression into the ECC supply line even before the RWT is drained away. Therefore, it is important to check if the operational limit of the RWT water level is set at a value higher than the critical height that causes a dip formation on the free surface of a draining liquid. In the previous work, such complex unsteady flow fields both in a simple water tank and in the RWT at the Korean standard nuclear power plant have been simulated using the CFX5.10 code which is well-known as one of the well-validated commercial CFD (Computational Fluid Dynamics) codes. However, for the simplicity of those calculations the Coriolis force has not been taken into account. Thus, in the present paper, the effect of Coriolis force-induced vortex flow on the dip formation of dip has been investigated for the simple water tank to confirm validity of the previous work. To do this the unsteady flow fields accompanied by vortex in the simple water tank has been simulated using the CFX5.10 code

The Effect of Coriolis Force on the Formation of Dip on the Free Surface of Water Draining from a Tank

Energy Technology Data Exchange (ETDEWEB)

Jo, Jong Chull; Kang, Dong Gu; Kim, Hho Jhung; Roh, Kyung Wan; Yune, Young Gill [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2007-10-15

For the case of RWT (refueling water tank) connecting to the ECC (emergency core cooling) line, it can be surmised that there is a possibility of ECC pump failure due to air ingression into the ECC supply line even before the RWT is drained away. Therefore, it is important to check if the operational limit of the RWT water level is set at a value higher than the critical height that causes a dip formation on the free surface of a draining liquid. In the previous work, such complex unsteady flow fields both in a simple water tank and in the RWT at the Korean standard nuclear power plant have been simulated using the CFX5.10 code which is well-known as one of the well-validated commercial CFD (Computational Fluid Dynamics) codes. However, for the simplicity of those calculations the Coriolis force has not been taken into account. Thus, in the present paper, the effect of Coriolis force-induced vortex flow on the dip formation of dip has been investigated for the simple water tank to confirm validity of the previous work. To do this the unsteady flow fields accompanied by vortex in the simple water tank has been simulated using the CFX5.10 code.

Heterogeneous Rock Simulation Using DIP-Micromechanics-Statistical Methods

Directory of Open Access Journals (Sweden)

H. Molladavoodi

2018-01-01

Full Text Available Rock as a natural material is heterogeneous. Rock material consists of minerals, crystals, cement, grains, and microcracks. Each component of rock has a different mechanical behavior under applied loading condition. Therefore, rock component distribution has an important effect on rock mechanical behavior, especially in the postpeak region. In this paper, the rock sample was studied by digital image processing (DIP, micromechanics, and statistical methods. Using image processing, volume fractions of the rock minerals composing the rock sample were evaluated precisely. The mechanical properties of the rock matrix were determined based on upscaling micromechanics. In order to consider the rock heterogeneities effect on mechanical behavior, the heterogeneity index was calculated in a framework of statistical method. A Weibull distribution function was fitted to the Young modulus distribution of minerals. Finally, statistical and Mohr–Coulomb strain-softening models were used simultaneously as a constitutive model in DEM code. The acoustic emission, strain energy release, and the effect of rock heterogeneities on the postpeak behavior process were investigated. The numerical results are in good agreement with experimental data.

Hot Fuel Examination Facility (HFEF)

Data.gov (United States)

Federal Laboratory Consortium — The Hot Fuel Examination Facility (HFEF) is one of the largest hot cells dedicated to radioactive materials research at Idaho National Laboratory (INL). The nation's...

Dip in the atmospheric CO2 level during the mid-1960's

International Nuclear Information System (INIS)

Bacastow, R.

1979-01-01

Removal of the southern oscillation effect from the CO 2 records at Mauna Loa, Hawaii, and the South Pole reveals corresponding decreases following the Agung eruption in 1963. The period of the decreases roughly corresponds to the period of reduced solar transmittance, as measured at Mauna Loa. It is suggested that the decrease in CO 2 level is due to reduced sea surface temperatures, for which there is some direct evidence. The temperature anomaly required to produce the CO 2 level dip is calculated on the basis of several simple models and found to be close to that observed

Campylobacter, Salmonella, and Escherichia coli on broiler carcasses subjected to a high pH scald and low pH postpick chlorine dip.

Science.gov (United States)

Berrang, M E; Windham, W R; Meinersmann, R J

2011-04-01

The objective of this study was to determine the individual and combined effects of a high pH scald and a postpick chlorine dip on bacteria present on broiler carcasses. In each of 3 replications, a flock was sampled at several sites within a commercial broiler processing plant. Carcasses were sampled by whole carcass rinse before and after treated scalding at mean pH 9.89 or control scalding at mean pH 6.88. Other carcasses from the same flock run on both the treated and control scald lines were collected and sampled before and after a chlorine dip tank operated at mean total chlorine level of 83.3 mg/kg and pH 6.04. Rinses were cultured for numbers of Campylobacter and Escherichia coli and presence or absence of Salmonella. High pH scald was more effective than standard scald to lessen the prevalence and numbers of Campylobacter on broiler carcasses; a lower prevalence was maintained through the postpick chlorine dip tank. The pH of the scald tank made no difference in numbers of E. coli recovered from broiler carcasses at any tested point on the processing line. High pH scald was not more effective than standard scald to lessen Salmonella prevalence. Furthermore, it is unclear why the postpick chlorine dip effectively lessened Salmonella prevalence on only the control scald line. Although no evidence exists that these treatments have an additive effect when used in series, each treatment shows some promise individually. Further optimization may result in more effective decontamination of broiler carcasses.

D-dimer, factor VIII and von Willebrand factor predict a non-dipping pattern of blood pressure in hypertensive patients.

Science.gov (United States)

Agorasti, Athanasia; Trivellas, Theodoros; Mourvati, Efthimia; Papadopoulos, Vasilios; Tsatalas, Konstantinos; Vargemezis, Vasilios; Passadakis, Ploumis

2013-06-01

The aim of this study is to assess whether the haemostatic markers D-dimer, factor VIII (FVIII) and von Willebrand factor (VWF) are predictive of non-dipping status in treated hypertensive patients; so, as easy available laboratory data can predict non-dipping pattern and help with the selection of the patients whom circadian blood pressure should be re-examined. Forty treated hypertensive patients with essential hypertension were included in the study. Twenty-four-hour ambulatory blood pressure monitoring was performed in all patients. Daytime and nocturnal average systolic, diastolic and mean blood pressures were calculated. Patients were characterised as "non-dippers" on the basis of a less than 10 % decline in nocturnal blood pressure (BP); either systolic or diastolic or mean (MAP). D-dimer as marker of fibrinolytic function, FVIII activity and VWF antigen as marker of endothelial dysfunction were measured on plasma. The predictive efficiency was analysed by receiver operating characteristic (ROC) curves. Youden index was used for the estimation of the cut-off points and the associated values for sensitivity and 1-specificity. Plasma levels of D-dimer, FVIII and VWF were significantly higher in non-dippers as compared with dippers, irrespective of the classification used (BP index); all P AUC(ROC) = 0.697, 0.715 and 0.774), FVIII (AUC(ROC) = 0.714, 0.692 and 0.755) and VWF (AUC(ROC) = 0.706, 0.740 and 0.708) in distinguishing non-dipping pattern (systolic, diastolic or mean) in the study population; all P 168 ng/ml (sensitivity/1-specificity for systolic BP non-dippers of 0.789/0.381, for diastolic BP non-dippers 0.923/0.444 and for MAP non-dippers 0.875/0.375). In conclusion, D-dimer has a good predictive value for non-dipping pattern and the decision for the 24-h ambulatory blood pressure re-monitoring among dippers could rely on its values.

New tools for digital medical image processing implemented in DIP software

International Nuclear Information System (INIS)

Araujo, Erica A.C.; Santana, Ivan E.; Lima, Fernando R.A.; Viera, Jose W.

2011-01-01

The anthropomorphic models used in computational dosimetry, also called phantoms, are mostly built from stacks of images CT (Computed Tomography) or MRI (Magnetic Resonance Imaging) obtained from scans of patients or volunteers. The construction of voxel phantoms requires computational processing for transforming image formats, dimensional image compression (2D) to form three-dimensional arrays (3D), quantization, resampling, enhancement, restoration and image segmentation, among others. Hardly the computational dosimetry researcher finds all these skills into a single software and often it results in a decreased development of their research or inadequate use of alternative tools. The need to integrate the various tasks of the original digital image processing to obtain an image that can be used in a computational model of exposure led to the development of software DIP (Digital Image Processing). This software reads, writes and edits binary files containing the 3D matrix corresponding to a stack of cross-sectional images of a given geometry that can be a human body or other volume of interest. It can also read any type of computer image and do conversions. When the task involves only one output image, it is saved in the JPEG standard Windows. When it involves a stack of images, the binary output file is called SGI (Interactive Graphic Simulations, a symbol already used in other publications of the Research Group in Numerical Dosimetry). The following paper presents the third version of the DIP software and emphasizes the new tools it implemented. Currently it has the menus Basics, Views, Spatial Domain, Frequency Domain, Segmentations and Study. Each menu contains items and subitems with features that generally require an image as input and produce an image or an attribute in the output. (author)

Shaping optimal zinc coating on the surface of high-quality ductile iron casting. Part I – Moulding technologies vs. zinc coating

Directory of Open Access Journals (Sweden)

Szczęsny A.

2017-03-01

Full Text Available Studies have demonstrated that in the process of hot dip galvanizing the decisive influence on the mechanism of zinc coating formation and properties has the quality of the mechanically untreated (raw surface layer of the galvanized product. The terms “casting surface layer” denote various parameters of the microstructure, including the type of metal matrix, the number of grains and the size of graphite nodules, possible presence of hard spots (the precipitates of eutectic cementite and parameters of the surface condition. The completed research has allowed linking the manufacturing technology of ductile iron castings with the process of hot dip galvanizing.

Assessment of Optimum Value for Dip Angle and Locking Rate Parameters in Makran Subduction Zone

Science.gov (United States)

Safari, A.; Abolghasem, A. M.; Abedini, N.; Mousavi, Z.

2017-09-01

Makran subduction zone is one of the convergent areas that have been studied by spatial geodesy. Makran zone is located in the South Eastern of Iran and South of Pakistan forming the part of Eurasian-Arabian plate's border where oceanic crust in the Arabian plate (or in Oman Sea) subducts under the Eurasian plate ( Farhoudi and Karig, 1977). Due to lack of historical and modern tools in the area, a sampling of sparse measurements of the permanent GPS stations and temporary stations (campaign) has been conducted in the past decade. Makran subduction zone from different perspectives has unusual behaviour: For example, the Eastern and Western parts of the region have very different seismicity and also dip angle of subducted plate is in about 2 to 8 degrees that this value due to the dip angle in other subduction zone is very low. In this study, we want to find the best possible value for parameters that differs Makran subduction zone from other subduction zones. Rigid block modelling method was used to determine these parameters. From the velocity vectors calculated from GPS observations in this area, block model is formed. These observations are obtained from GPS stations that a number of them are located in South Eastern Iran and South Western Pakistan and a station located in North Eastern Oman. According to previous studies in which the locking depth of Makran subduction zone is 38km (Frohling, 2016), in the preparation of this model, parameter value of at least 38 km is considered. With this function, the amount of 2 degree value is the best value for dip angle but for the locking rate there is not any specified amount. Because the proposed model is not sensitive to this parameter. So we can not expect big earthquakes in West of Makran or a low seismicity activity in there but the proposed model definitely shows the Makran subduction layer is locked.

3D Dynamic Rupture Simulations along Dipping Faults, with a focus on the Wasatch Fault Zone, Utah

Science.gov (United States)

Withers, K.; Moschetti, M. P.

2017-12-01

We study dynamic rupture and ground motion from dip-slip faults in regions that have high-seismic hazard, such as the Wasatch fault zone, Utah. Previous numerical simulations have modeled deterministic ground motion along segments of this fault in the heavily populated regions near Salt Lake City but were restricted to low frequencies ( 1 Hz). We seek to better understand the rupture process and assess broadband ground motions and variability from the Wasatch Fault Zone by extending deterministic ground motion prediction to higher frequencies (up to 5 Hz). We perform simulations along a dipping normal fault (40 x 20 km along strike and width, respectively) with characteristics derived from geologic observations to generate a suite of ruptures > Mw 6.5. This approach utilizes dynamic simulations (fully physics-based models, where the initial stress drop and friction law are imposed) using a summation by parts (SBP) method. The simulations include rough-fault topography following a self-similar fractal distribution (over length scales from 100 m to the size of the fault) in addition to off-fault plasticity. Energy losses from heat and other mechanisms, modeled as anelastic attenuation, are also included, as well as free-surface topography, which can significantly affect ground motion patterns. We compare the effect of material structure and both rate and state and slip-weakening friction laws have on rupture propagation. The simulations show reduced slip and moment release in the near surface with the inclusion of plasticity, better agreeing with observations of shallow slip deficit. Long-wavelength fault geometry imparts a non-uniform stress distribution along both dip and strike, influencing the preferred rupture direction and hypocenter location, potentially important for seismic hazard estimation.

Measuring hot flash phenomenonology using ambulatory prospective digital diaries

Science.gov (United States)

Fisher, William I.; Thurston, Rebecca C.

2016-01-01

Objective This study provides the description, protocol, and results from a novel prospective ambulatory digital hot flash phenomenon diary. Methods This study included 152 midlife women with daily hot flashes who completed an ambulatory electronic hot flash diary continuously for the waking hours of 3 consecutive days. In this diary, women recorded their hot flashes and accompanying characteristics and associations as the hot flashes occurred. Results Self-reported hot flash severity on the digital diaries indicated that the majority of hot flashes were rated as mild (41.3%) or moderate (43.7%). Severe (13.1%) and very severe (1.8%) hot flashes were less common. Hot flash bother ratings were rated as mild (43%), or moderate (33.5%), with fewer hot flashes reported bothersome (17.5%) or very bothersome (6%). The majority of hot flashes were reported as occurring on the on the face (78.9%), neck (74.7%), and chest (61.3%). Prickly skin was reported concurrently with 32% of hot flashes, 7% with anxiety and 5% with nausea. A novel finding, 38% of hot flashes were accompanied by a premonitory aura. Conclusion A prospective electronic digital hot flash diary allows for a more precise quantitation of hot flashes while overcoming many of the limitations of commonly employed retrospective questionnaires and paper diaries. Unique insights into the phenomenology, loci and associated characteristics of hot flashes were obtained using this device. The digital hot flash phenomenology diary is recommended for future ambulatory studies of hot flashes as a prospective measure of the hot flash experience. PMID:27404030

Computational prediction of protein hot spot residues.

Science.gov (United States)

Morrow, John Kenneth; Zhang, Shuxing

2012-01-01

Most biological processes involve multiple proteins interacting with each other. It has been recently discovered that certain residues in these protein-protein interactions, which are called hot spots, contribute more significantly to binding affinity than others. Hot spot residues have unique and diverse energetic properties that make them challenging yet important targets in the modulation of protein-protein complexes. Design of therapeutic agents that interact with hot spot residues has proven to be a valid methodology in disrupting unwanted protein-protein interactions. Using biological methods to determine which residues are hot spots can be costly and time consuming. Recent advances in computational approaches to predict hot spots have incorporated a myriad of features, and have shown increasing predictive successes. Here we review the state of knowledge around protein-protein interactions, hot spots, and give an overview of multiple in silico prediction techniques of hot spot residues.

Social integration, social contacts, and blood pressure dipping in African-Americans and whites.

Science.gov (United States)

Troxel, Wendy M; Buysse, Daniel J; Hall, Martica; Kamarck, Thomas W; Strollo, Patrick J; Owens, Jane F; Reis, Steven E; Matthews, Karen A

2010-02-01

Both the size and diversity of an individual's social network are strongly and prospectively linked with cardiovascular morbidity and mortality. Social relationships may influence cardiovascular outcomes, at least in part, via their impact on physiologic pathways influenced by stress, such as daytime blood pressure (BP) levels. However, scant research has examined whether social relationships influence key nocturnal pathways, such as nocturnal BP dipping. The current study examined the degree to which social integration, as measured by participants' reported engagement in a range of different types of social relationships, and the frequency of daily social contacts influence the ratio of night/day mean arterial pressure (MAP) in a community sample of African-American and white men and women (N = 224). In addition, we examined the degree to which observed associations persisted after statistical adjustment for factors known to covary with nocturnal BP, including objective measures of sleep, catecholamines, health behaviors, and comorbidities. In fully adjusted models, there was a significant association between both social integration and frequency of social contacts and the ratio of night/day MAP, indicating that socially isolated individuals were more likely to have blunted nocturnal BP-dipping profiles. There was also a significant interaction between social contact frequency and ethnicity, suggesting that the benefits of social relationships were particularly evident in African-Americans. These findings contribute to our understanding of how social integration or conversely, social isolation, influences cardiovascular risk.

Uncertainty analysis for hot channel

International Nuclear Information System (INIS)

Panka, I.; Kereszturi, A.

2006-01-01

The fulfillment of the safety analysis acceptance criteria is usually evaluated by separate hot channel calculations using the results of neutronic or/and thermo hydraulic system calculations. In case of an ATWS event (inadvertent withdrawal of control assembly), according to the analysis, a number of fuel rods are experiencing DNB for a longer time and must be regarded as failed. Their number must be determined for a further evaluation of the radiological consequences. In the deterministic approach, the global power history must be multiplied by different hot channel factors (kx) taking into account the radial power peaking factors for each fuel pin. If DNB occurs it is necessary to perform a few number of hot channel calculations to determine the limiting kx leading just to DNB and fuel failure (the conservative DNBR limit is 1.33). Knowing the pin power distribution from the core design calculation, the number of failed fuel pins can be calculated. The above procedure can be performed by conservative assumptions (e.g. conservative input parameters in the hot channel calculations), as well. In case of hot channel uncertainty analysis, the relevant input parameters (k x, mass flow, inlet temperature of the coolant, pin average burnup, initial gap size, selection of power history influencing the gap conductance value) of hot channel calculations and the DNBR limit are varied considering the respective uncertainties. An uncertainty analysis methodology was elaborated combining the response surface method with the one sided tolerance limit method of Wilks. The results of deterministic and uncertainty hot channel calculations are compared regarding to the number of failed fuel rods, max. temperature of the clad surface and max. temperature of the fuel (Authors)

3-D thermoelastic analysis of the straight section of a PWR hot leg containing a hot spot using BEM

International Nuclear Information System (INIS)

Bains, R.S.; Sugimoto, J.

1995-01-01

A 3-D steady state thermoelastic analysis using the boundary element method has been successfully employed to investigate the structural response of the straight section of a pressurised water reactor hot leg containing a localised hot spot. With the present severe accident thermal boundary conditions, the analysis produces a nonuniform expansion across the hot leg thickness. This expansion was most predominant on the inner surface, especially at the hot spot location where surface swelling was obtained. Furthermore, the hot spot generates large tangential and axial tensile stresses on the outer surface. These could be detrimental to the integrity of the hot leg by acting as potential sites of crack initiation and subsequent propagation. (orig.)

Hot-pressing steatite bodies

International Nuclear Information System (INIS)

Aparicio Arroyo, E.

1967-01-01

Requirements for some special nuclear engineering ceramic shapes are: big size, impervious, dimensional accuracy and good mechanical and dielectric properties. Limitations of te conventional methods and advantages of te hot pressing techniques for the manufacturing of these shapes are discussed. Hot pressing characteristics of a certain steatite powder are studied. Occurrence of an optimum densification temperature just above the tale decomposition range is found. Experimental data show that the height/diameter ratio of the specimen has no effect on the sintering conditions. Increasing darkness from the graphite mould is detected above the optimum temperature. The hot-pressed steatite is compared with a fired dry-pressed sample of the same composition. (Author) 13 refs

HOT 2017

DEFF Research Database (Denmark)

Hannibal, Sara Stefansen

HOT er en kvalitativ undersøgelse, der hvert år diskuterer og undersøger en lille udvalgt skare af danskkyndige fagpersoners bud på, hvad de er optagede af på literacyområdet her og nu – altså hvilke emner, de vil vurdere som aktuelle at forholde sig til i deres nuværende praksis.......HOT er en kvalitativ undersøgelse, der hvert år diskuterer og undersøger en lille udvalgt skare af danskkyndige fagpersoners bud på, hvad de er optagede af på literacyområdet her og nu – altså hvilke emner, de vil vurdere som aktuelle at forholde sig til i deres nuværende praksis....

[History of hot spring bath treatment in China].

Science.gov (United States)

Hao, Wanpeng; Wang, Xiaojun; Xiang, Yinghong; Gu Li, A Man; Li, Ming; Zhang, Xin

2011-07-01

As early as the 7th century B.C. (Western Zhou Dynasty), there is a recording as 'spring which contains sulfur could treat disease' on the Wentang Stele written by WANG Bao. Wenquan Fu written by ZHANG Heng in the Easten Han Dynasty also mentioned hot spring bath treatment. The distribution of hot springs in China has been summarized by LI Daoyuan in the Northern Wei Dynasty in his Shuijingzhu which recorded hot springs in 41 places and interpreted the definition of hot spring. Bencao Shiyi (by CHEN Cangqi, Tang Dynasty) discussed the formation of and indications for hot springs. HU Zai in the Song Dynasty pointed out distinguishing hot springs according to water quality in his book Yuyin Conghua. TANG Shenwei in the Song Dynasty noted in Jingshi Zhenglei Beiji Bencao that hot spring bath treatment should be combined with diet. Shiwu Bencao (Ming Dynasty) classified hot springs into sulfur springs, arsenicum springs, cinnabar springs, aluminite springs, etc. and pointed out their individual indications. Geologists did not start the work on distribution and water quality analysis of hot springs until the first half of the 20th century. There are 972 hot springs in Wenquan Jiyao (written by geologist ZHANG Hongzhao and published in 1956). In July 1982, the First National Geothermal Conference was held and it reported that there were more than 2600 hot springs in China. Since the second half of the 20th century, hot spring sanatoriums and rehabilitation centers have been established, which promoted the development of hot spring bath treatment.

Effect of integration of oxalic acid and hot water treatments on postharvest quality of rambutan (Nephelium lappaceum L. cv. Anak Sekolah) under modified atmosphere packaging.

Science.gov (United States)

Hafiz, Ahmad Faiz Ahmad; Keat, Yeoh Wei; Ali, Asgar

2017-06-01

The shelf life of rambutan is often limited due to rapid water loss from the spinterns and browning of the pericarp. An integrated approach, which combined hot water treatment (HWT) (56 °C for 1 min), oxalic acid (OA) dip (10% for 10 min) and modified atmosphere packaging (MAP), was used to study their effectiveness on the quality of rambutan during storage (10 °C, 90-95% relative humidity). Significant differences were observed in rambutan quality with the combination of MAP + HWT + OA after 20 days of storage. This treatment combination resulted into better retention of firmness and colour (L and a* values) than in the control. Change in the total soluble solid content was significantly delayed however the titratable acidity showed no significant change in comparison to the control at the end of storage.

Hot workability of aluminium alloys

International Nuclear Information System (INIS)

Yoo, Yeon Chul; Oh, Kyung Jin

1986-01-01

Hot Workability of aluminium alloys, 2024, 6061 and 7075, has been studied by hot torsion tests at temperatures from 320 to 515 deg C and at strain rates from 1.26 x 10 -3 to 5.71 x 10 -3 sec -1 . Hot working condition of these aluminium alloys was determined quantitatively from the constitutive equations obtained from flow stress curves in torsion. Experimental data of the logarith of the Zener-Hollomonn parameter showed good linear relationships to the logarith of sinh(ασ-bar)

Interplay of superconductivity and bosonic coupling in the peak-dip-hump structure of Bi2Sr2CaCu2O8 +δ

Science.gov (United States)

Miller, Tristan L.; Zhang, Wentao; Ma, Jonathan; Eisaki, Hiroshi; Moore, Joel E.; Lanzara, Alessandra

2018-04-01

Because of the important role of electron-boson interactions in conventional superconductivity, it has long been asked whether any similar mechanism is at play in high-temperature cuprate superconductors. Evidence for strong electron-boson coupling is observed in cuprates with angle-resolved photoemission spectroscopy (ARPES), in the form of a dispersion kink and peak-dip-hump structure. What is missing is evidence of a causal relation to superconductivity. Here we revisit the problem using the technique of time-resolved ARPES on Bi2Sr2CaCu2O8 +δ . We focus on the peak-dip-hump structure, and show that laser pulses shift spectral weight into the dip as superconductivity is destroyed on picosecond time scales. We compare our results to simulations of Eliashberg theory in a superconductor with an Einstein boson, and find that the magnitude of the shift in spectral weight depends on the degree to which the bosonic mode contributes to superconductivity. Further study could address one of the longstanding mysteries of high-temperature superconductivity.

Hot dry rock heat mining

International Nuclear Information System (INIS)

Duchane, D.V.

1992-01-01

Geothermal energy utilizing fluids from natural sources is currently exploited on a commercial scale at sites around the world. A much greater geothermal resource exists, however, in the form of hot rock at depth which is essentially dry. This hot dry rock (HDR) resource is found almost everywhere, but the depth at which usefully high temperatures are reached varies from place to place. The technology to mine the thermal energy from HDR has been under development for a number of years. Using techniques adapted from the petroleum industry, water is pumped at high pressure down an injection well to a region of usefully hot rock. The pressure forces open natural joints to form a reservoir consisting of a small amount of water dispensed in a large volume of hot rock. This reservoir is tapped by second well located at some distance from the first, and the heated water is brought to the surface where its thermal energy is extracted. The same water is then recirculated to mine more heat. Economic studies have indicated that it may be possible to produce electricity at competitive prices today in regions where hot rock is found relatively close to the surface

Harvest maturity, pre-cutting wash and post-processing dip to improve quality of fresh-cut carambola fruit

Science.gov (United States)

‘Arkin’ carambola (Averrhoa carambola L.) fruit harvested at color break or full yellow stage were washed with or without an alkaline solution (pH 12), cut to 10 mm slices, dipped in calcium ascorbate (Ca ASA), ascorbic acid (ASA) or water, and packaged in perforated clamshells for up to 14 days sto...

Mercury content in Hot Springs

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, R

1974-01-01

A method of determination of mercury in hot spring waters by flameless atomic absorption spectrophotometry is described. Further, the mercury content and the chemical behavior of the elementary mercury in hot springs are described. Sulfide and iodide ions interfered with the determination of mercury by the reduction-vapor phase technique. These interferences could, however, be minimized by the addition of potassium permanganate. Waters collected from 55 hot springs were found to contain up to 26.0 ppb mercury. High concentrations of mercury have been found in waters from Shimoburo Springs, Aomori (10.0 ppb), Osorezan Springs, Aomori (1.3 approximately 18.8 ppb), Gosyogake Springs, Akita (26.0 ppb), Manza Springs, Gunma (0.30 approximately 19.5 ppb) and Kusatu Springs, Gunma (1.70 approximately 4.50 ppb). These hot springs were acid waters containing a relatively high quantity of chloride or sulfate.

Disturbance Impacts on Thermal Hot Spots and Hot Moments at the Peatland-Atmosphere Interface

Science.gov (United States)

Leonard, R. M.; Kettridge, N.; Devito, K. J.; Petrone, R. M.; Mendoza, C. A.; Waddington, J. M.; Krause, S.

2018-01-01

Soil-surface temperature acts as a master variable driving nonlinear terrestrial ecohydrological, biogeochemical, and micrometeorological processes, inducing short-lived or spatially isolated extremes across heterogeneous landscape surfaces. However, subcanopy soil-surface temperatures have been, to date, characterized through isolated, spatially discrete measurements. Using spatially complex forested northern peatlands as an exemplar ecosystem, we explore the high-resolution spatiotemporal thermal behavior of this critical interface and its response to disturbances by using Fiber-Optic Distributed Temperature Sensing. Soil-surface thermal patterning was identified from 1.9 million temperature measurements under undisturbed, trees removed and vascular subcanopy removed conditions. Removing layers of the structurally diverse vegetation canopy not only increased mean temperatures but it shifted the spatial and temporal distribution, range, and longevity of thermal hot spots and hot moments. We argue that linking hot spots and/or hot moments with spatially variable ecosystem processes and feedbacks is key for predicting ecosystem function and resilience.

VARIABILITY IN HOT CARBON-DOMINATED ATMOSPHERE (HOT DQ) WHITE DWARFS: RAPID ROTATION?

Energy Technology Data Exchange (ETDEWEB)

Williams, Kurtis A.; Bierwagen, Michael [Department of Physics and Astrophysics, Texas A and M University-Commerce, P.O. Box 3011, Commerce, TX, 75429 (United States); Montgomery, M. H.; Winget, D. E.; Falcon, Ross E., E-mail: Kurtis.Williams@tamuc.edu [Department of Astronomy, University of Texas, 1 University Station C1400, Austin, TX, 78712 (United States)

2016-01-20

Hot white dwarfs (WDs) with carbon-dominated atmospheres (hot DQs) are a cryptic class of WDs. In addition to their deficiency of hydrogen and helium, most of these stars are highly magnetic, and a large fraction vary in luminosity. This variability has been ascribed to nonradial pulsations, but increasing data call this explanation into question. We present studies of short-term variability in seven hot DQ WDs. Three (SDSS J1426+5752, SDSS J2200−0741, and SDSS J2348−0942) were known to be variable. Their photometric modulations are coherent over at least two years, and we find no evidence for variability at frequencies that are not harmonics. We present the first time-series photometry for three additional hot DQs (SDSS J0236−0734, SDSS J1402+3818, and SDSS J1615+4543); none are observed to vary, but the signal-to-noise is low. Finally, we present high speed photometry for SDSS J0005−1002, known to exhibit a 2.1-day photometric variation; we do not observe any short-term variability. Monoperiodicity is rare among pulsating WDs, so we contemplate whether the photometric variability is due to rotation rather than pulsations; similar hypotheses have been raised by other researchers. If the variability is due to rotation, then hot DQ WDs as a class contain many rapid rotators. Given the lack of companions to these stars, the origin of any fast rotation is unclear—both massive progenitor stars and double degenerate merger remnants are possibilities. We end with suggestions of future work that would best clarify the nature of these rare, intriguing objects.

Mechanical shielded hot cell

International Nuclear Information System (INIS)

Higgy, H.R.; Abdel-Rassoul, A.A.

1983-01-01

A plan to erect a mechanical shielded hot cell in the process hall of the Radiochemical Laboratory at Inchas is described. The hot cell is designed for safe handling of spent fuel bundles, from the Inchas reactor, and for dismantling and cutting the fuel rods in preparation for subsequent treatment. The biological shielding allows for the safe handling of a total radioactivity level up to 10,000 MeV-Ci. The hot cell consists of an α-tight stainless-steel box, connected to a γ-shielded SAS, through an air-lock containing a movable carriage. The α-box is tightly connected with six dry-storage cavities for adequate storage of the spent fuel bundles. Both the α-box, with the dry-storage cavities, and the SAS are surrounded by 200-mm thick biological lead shielding. The α-box is equipped with two master-slave manipulators, a lead-glass window, a monorail crane and Padirac and Minirag systems. The SAS is equipped with a lead-glass window, tong manipulator, a shielded pit and a mechanism for the entry of the spent fuel bundle. The hot cell is served by adequate ventilation and monitoring systems. (author)

Synthesis of LSM films deposited by dip-coating on YSZ substrate

International Nuclear Information System (INIS)

Conceicao, Leandro da; Souza, Mariana M.V.M.; Ribeiro, Nielson F.P.

2010-01-01

The dip-coating process was used to deposit films of La 0.7 Sr 0. 3MnO 3 (LSM) used as cathode in solid oxide fuel cells (SOFC). In this study we evaluated the relationship between the deposition parameters such as speed of withdrawal and number of deposited layers of LSM film on a substrate of 8% YSZ commercial, and structural properties, such as thickness and formation of cracks. The structure and morphology of the films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). With parameters set the film had good adhesion to the substrate with a thickness around 10 μm, showing possible adherence problems when more than one layer is deposited on the substrate. (author)

Preparation of transparent conductive indium tin oxide thin films from nanocrystalline indium tin hydroxide by dip-coating method

International Nuclear Information System (INIS)

Koroesi, Laszlo; Papp, Szilvia; Dekany, Imre

2011-01-01

Indium tin oxide (ITO) thin films with well-controlled layer thickness were produced by dip-coating method. The ITO was synthesized by a sol-gel technique involving the use of aqueous InCl 3 , SnCl 4 and NH 3 solutions. To obtain stable sols for thin film preparation, as-prepared Sn-doped indium hydroxide was dialyzed, aged, and dispersed in ethanol. Polyvinylpyrrolidone (PVP) was applied to enhance the stability of the resulting ethanolic sols. The transparent, conductive ITO films on glass substrates were characterized by X-ray diffraction, scanning electron microscopy and UV-Vis spectroscopy. The ITO layer thickness increased linearly during the dipping cycles, which permits excellent controllability of the film thickness in the range ∼ 40-1160 nm. After calcination at 550 o C, the initial indium tin hydroxide films were transformed completely to nanocrystalline ITO with cubic and rhombohedral structure. The effects of PVP on the optical, morphological and electrical properties of ITO are discussed.

Sanitary hot water; Eau chaude sanitaire

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

Cegibat, the information-recommendation agency of Gaz de France for building engineering professionals, has organized this conference meeting on sanitary hot water to present the solutions proposed by Gaz de France to meet its clients requirements in terms of water quality, comfort, energy conservation and respect of the environment: quantitative aspects of the hot water needs, qualitative aspects, presentation of the Dolce Vita offer for residential buildings, gas water heaters and boilers, combined solar-thermal/natural gas solutions, key-specifications of hot water distribution systems, testimony: implementation of a gas hot water reservoir and two accumulation boilers in an apartment building for young workers. (J.S.)

OUT Success Stories: Solar Hot Water Technology

International Nuclear Information System (INIS)

Clyne, R.

2000-01-01

Solar hot water technology was made great strides in the past two decades. Every home, commercial building, and industrial facility requires hot water. DOE has helped to develop reliable and durable solar hot water systems. For industrial applications, the growth potential lies in large-scale systems, using flat-plate and trough-type collectors. Flat-plate collectors are commonly used in residential hot water systems and can be integrated into the architectural design of the building

OUT Success Stories: Solar Hot Water Technology

Science.gov (United States)

Clyne, R.

2000-08-01

Solar hot water technology was made great strides in the past two decades. Every home, commercial building, and industrial facility requires hot water. DOE has helped to develop reliable and durable solar hot water systems. For industrial applications, the growth potential lies in large-scale systems, using flat-plate and trough-type collectors. Flat-plate collectors are commonly used in residential hot water systems and can be integrated into the architectural design of the building.

Letter to the editor: Electric field fluctuations (25-35 min in the midnight dip equatorial ionosphere

Directory of Open Access Journals (Sweden)

J. Hanumath Sastri

2000-02-01

Full Text Available Measurements with a HF Doppler sounder at Kodaikanal (10.2°N, 77.5°E, geomagnetic latitude 0.8°N showed conspicuous quasi-periodic fluctuations (period 25-35 min in F region vertical plasma drift, Vz in the interval 0047-0210 IST on the night of 23/24 December, 1991 (Ap = 14, Kp < 4-. The fluctuations in F region vertical drift are found to be coherent with variations in Bz (north-south component of interplanetary magnetic field (IMF, in geomagnetic H/X components at high-mid latitude locations both in the sunlit and dark hemispheres and near the dayside dip equator, suggestive of DP2 origin. But the polarity of the electric field fluctuations at the midnight dip equator (eastward is the same as the dayside equator inferred from magnetic variations, contrary to what is expected of equatorial DP2. The origin of the coherent occurrence of equatorial electric field fluctuations in the DP2 range of the same sign in the day and night hemispheres is unclear and merits further investigations.Key words: Ionosphere (electric fields and currents; equatorial ionosphere; ionosphere-magnetosphere interactions

Investigation of hot air balloon fatalities.

Science.gov (United States)

McConnell, T S; Smialek, J E; Capron, R G

1985-04-01

The rising popularity of the sport of hot air ballooning has been accompanied by several recent incidents, both in this country and other parts of the world, where mechanical defects and the improper operation of balloons have resulted in several fatalities. A study was conducted to identify the location and frequency of hot air ballooning accidents. Furthermore, the study attempted to identify those accidents that were the result of improper handling on the part of the balloon operators and those that were related to specific defects in the construction of the balloon. This paper presents a background of the sport of hot air ballooning, together with an analysis of the construction of a typical hot air balloon, pointing out the specific areas where defects may occur that could result in a potential fatal balloon crash. Specific attention is given to the two recent balloon crashes that occurred in Albuquerque, N.M., hot air balloon capital of the world, and that resulted in multiple fatalities.

Dips, ramps, and rolls- Evidence for paleotopographic and syn-depositional fault control on the Western Kentucky No. 4 coal bed, tradewater formation (Bolsovian) Illinois Basin

Science.gov (United States)

Greb, S.F.; Eble, C.F.; Williams, D.A.; Nelson, W.J.

2001-01-01

The Western Kentucky No. 4 coal is a high-volatile B to high-volatile C bituminous coal that has been heavily mined along the southern margin of the Western Kentucky Coal Field. The seam has a reputation for rolling floor elevation. Elongate trends of floor depressions are referred to as "dips" and "rolls" by miners. Some are relatively narrow and straight to slightly curvilinear in plan view, with generally symmetric to slightly asymmetric cross-sections. Others are broader and asymmetric in section, with sharp dips on one limb and gradual, ramp-like dips on the other. Some limbs change laterally from gradual dip, to sharp dip, to offset of the coal. Lateral changes in the rate of floor elevation dip are often associated with changes in coal thickness, and in underground mines, changes in floor elevation are sometimes associated with roof falls and haulage problems. In order to test if coal thickness changes within floor depressions were associated with changes in palynology, petrography and coal quality, the coal was sampled at a surface mine across a broad. ramp-like depression that showed down-dip coal thickening. Increment samples of coal from a thick (150 cm), down-ramp and thinner (127 cm), up-ramp position at one surface mine correlate well between sample sites (a distance of 60 m) except for a single increment. The anomalous increment (31 cm) in the lower-middle part of the thick coal bed contained 20% more Lycospora orbicula spores. The rolling floor elevations noted in the study mines are inferred to have been formed as a result of pre-peat paleotopographic depressions, syn-depositional faulting, fault-controlled pre-peat paleotopography, and from compaction beneath post-depositional channels and slumps. Although the association of thick coal with linear trends and inferred faults has been used in other basins to infer syn-depositional faulting, changes in palynology within increment samples of the seam along a structural ramp in this study provide

Study on conditional probability of surface rupture: effect of fault dip and width of seismogenic layer

Science.gov (United States)

Inoue, N.

2017-12-01

The conditional probability of surface ruptures is affected by various factors, such as shallow material properties, process of earthquakes, ground motions and so on. Toda (2013) pointed out difference of the conditional probability of strike and reverse fault by considering the fault dip and width of seismogenic layer. This study evaluated conditional probability of surface rupture based on following procedures. Fault geometry was determined from the randomly generated magnitude based on The Headquarters for Earthquake Research Promotion (2017) method. If the defined fault plane was not saturated in the assumed width of the seismogenic layer, the fault plane depth was randomly provided within the seismogenic layer. The logistic analysis was performed to two data sets: surface displacement calculated by dislocation methods (Wang et al., 2003) from the defined source fault, the depth of top of the defined source fault. The estimated conditional probability from surface displacement indicated higher probability of reverse faults than that of strike faults, and this result coincides to previous similar studies (i.e. Kagawa et al., 2004; Kataoka and Kusakabe, 2005). On the contrary, the probability estimated from the depth of the source fault indicated higher probability of thrust faults than that of strike and reverse faults, and this trend is similar to the conditional probability of PFDHA results (Youngs et al., 2003; Moss and Ross, 2011). The probability of combined simulated results of thrust and reverse also shows low probability. The worldwide compiled reverse fault data include low fault dip angle earthquake. On the other hand, in the case of Japanese reverse fault, there is possibility that the conditional probability of reverse faults with less low dip angle earthquake shows low probability and indicates similar probability of strike fault (i.e. Takao et al., 2013). In the future, numerical simulation by considering failure condition of surface by the source

Frequency metrology of the acetylene lines near 789 nm from lamb-dip measurements

Science.gov (United States)

Tao, Lei-Gang; Hua, Tian-Peng; Sun, Yu R.; Wang, Jin; Liu, An-Wen; Hu, Shui-Ming

2018-05-01

Lamb-dips of the ro-vibrational lines of 12C2H2 near 789 nm were recorded using cavity ring-down saturation spectroscopy. Calibrated by an optical frequency comb, frequencies of 45 acetylene lines were determined with an accuracy of 1.1 ×10-7 cm-1 (δν / ν = 8 ×10-12), which is over two orders of magnitude more accurate than previous Doppler-limited studies. An averaged shift of about 0.01 cm-1 were found by comparing the upper energies obtained in this work to those recently presented by Chubb et al. from a MARVEL analysis.

Fracture of the clavicle and second rib: an indirect injury from tricep dips.

Science.gov (United States)

Malavolta, Eduardo A; Assunção, Jorge H; Gracitelli, Mauro E; Lobo, Frederico L; Ferreira Neto, Arnaldo A

2016-01-01

Due to the recent rise in the interest in strength training, an increment in the number of lesions is expected, whether of the tendons, muscles, or bones. We describe a case of fracture involving the middle third of the clavicle and the second rib in a low-demand weightlifter. The fractures occurred suddenly while performing a triceps dips exercise, and the patient had no previous symptoms. He was treated conservatively and was able to return to sports six months later. To our knowledge, this is the first study describing the association of these fractures triggered by a single event of muscle contraction.

40 CFR 68.85 - Hot work permit.

Science.gov (United States)

2010-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CHEMICAL ACCIDENT PREVENTION PROVISIONS Program 3 Prevention Program § 68.85 Hot work permit. (a) The owner or operator shall issue a hot work permit for hot work operations conducted on or near a covered process. (b...

Benchmarking of Zinc Coatings for Corrosion Protection: A Detailed Characterization of Corrosion and Electrochemical Properties of Zinc Coatings

Energy Technology Data Exchange (ETDEWEB)

Wijesinghe, Sudesh L; Zixi, Tan [Singapore Institute of Manufacturing Technology, Nanyang Drive (Singapore)

2017-02-15

Due to various types of Zn coatings for many decades for various applications, it is imperative to study and compare their corrosion resistance properties of some of these. Here, we introduce a systematic methodology for evaluation and validation of corrosion protection properties of metallic coatings. According to this methodology, samples are were exposed in an advanced cyclic corrosion test chamber according to ISO 14993, and removed at the end of each withdrawal for respective corrosion and electrochemical characterization to evaluate both barrier and galvanic protection properties. Corrosion protection properties of coatings were evaluated by visual examination according to ISO 10289, mass loss and subsequent corrosion rate measurements, electrochemical properties, and advanced electrochemical scanning techniques. In this study, corrosion protection properties of a commercial zinc rich coating (ZRC) on AISI 1020 mild steel substrates were evaluated and benchmarked against hot dip galvanized (HDG). Results were correlated, and corrosion protection capabilities of the two coatings were compared. The zinc rich coating performed better than hot dip galvanized coating in terms of overall corrosion protection properties, according to the exposure and experimental conditions used in this study. It proved to be a suitable candidate to replace hot dip galvanized coatings for desired applications.

Effect of heat treatment oanas irradiation, and combined treatment on the shelf of fresh avocados (Persea americana L)

International Nuclear Information System (INIS)

Purwanto, Z.I.; Maha, Munsiah

1987-01-01

Effects of heat treatment, gamma irradiation, and combined treatments on the shelf-life of fresh avocados (Persea americana L.). Experiments to determine the effective irradiation conditions to prolong the shelf-life of fresh avocados were conducted at the centre for the Application of Isotopes washed and dried, then divided into 4 groups, namely for control (A), dipped in hot water at 40 0 C for 20 minutes (heat treatment, B), irradiated at a dose of 25 Gy (C), and combination of hot water dipping (40 0 C for 20 minutes) and irradiation at a 25 Gy (D). The samples were stored at room temperature. Evaluation on physical and chemical properties of the samples was done daily up to 10 days' storage. Parameters observed were texture, moisture and fat contents, percentage of weight loss, percentage of mature fruit, and subjective organoleptic evaluation. It was found that treated samples with and without combination treatment were still in good condition until 10 days of storage. It could be concluded that dipping in hot water, either alone or in combination with irradiation at a dose of 25 Gy could extend the shelf-life of fresh avocado up to 10 days at room temperature compared to only 5 days of the control. (author). 2 figs, 8 refs

Wear of Shaped Surfaces of PVD Coated Dies for Clinching

Directory of Open Access Journals (Sweden)

Miroslav Džupon

2017-11-01

Full Text Available A clinching method that uses a simple toolset consisting of a punch and a die, is utilized for joining lightweight materials. This paper is aimed at investigating the wear of the die cavity of a clinching tool. A clinching tool with a specially shaped cavity was used for joining thin hot-dip galvanized steel sheets. Various types of physical vapour deposition (PVD coatings such as ZrN, CrN and TiCN were deposited on the shaped surface of the die using Lateral Rotating Arc-Cathodes technology. Hot-dip galvanized steel sheets were used for testing the clinching tool. The material properties of PVD coatings that were deposited on the shaped part of the clinching die were evaluated. Finite Element Analysis was used to localize the area of the shaped part of the die and the part of surface area of the cylindrical die cavity of ϕ 5.0 mm, in which high contact pressure values were predicted. The prediction of the start of the wear cycle was verified experimentally by the clinching of 300 samples of hot-dip galvanized steel sheets. Unlike the CrN and ZrN coatings, the TiCN coating remained intact on the entire surface of the die.

The application of diode laser colorimetry coupled with fiber optic dipping probe for quantitative detection of a protein

International Nuclear Information System (INIS)

Kim, Sung Ho; Yoo, Jong Shin

1996-01-01

The in-situ, simple and inexpensive analysis of protein was achieved by the portable diode laser absorption spectrometry, which consisted of visible diode laser, photodiode, optical fiber and dipping probe. It gives comparable detection limit to the use of conventional UV/Vis spectrometer for the determination of protein by Lowry method.

Hot ductility of medium carbon steel with vanadium

International Nuclear Information System (INIS)

Lee, Chang-Hoon; Park, Jun-Young; Chung, JunHo; Park, Dae-Bum; Jang, Jin-Young; Huh, Sungyul; Ju Kim, Sung; Kang, Jun-Yun; Moon, Joonoh; Lee, Tae-Ho

2016-01-01

Hot ductility of medium carbon steel containing 0.52 wt% of carbon and 0.11 wt% of vanadium was investigated using a hot tensile test performed up to fracture. The hot ductility was evaluated by measuring the reduction of area of the fractured specimens, which were strained at a variety of test temperatures in a range of 600–1100 °C at a strain rate of 2×10"−"3/s. The hot ductility was excellent in a temperature range of 950–1100 °C, followed by a decrease of the hot ductility below 950 °C. The hot ductility continued to drop as the temperature was lowered to 600 °C. The loss of hot ductility in a temperature range of 800–950 °C, which is above the Ae_3 temperature, was due to V(C,N) precipitation at austenite grain boundaries. The further decline of hot ductility between 700 °C and 750 °C resulted from the transformation of ferrite films decorating austenite grain boundaries. The hot ductility continued to decrease at 650 °C or less, owing to ferrite films and the pearlite matrix, which is harder than ferrite. The pearlite was transformed from austenite due to relatively high carbon content.

Fiber-optic dipping liquid analyzer: theoretical and experimental study of light transmission

International Nuclear Information System (INIS)

Zhou Ai; Liu Zhihai; Yuan Libo

2009-01-01

A fiber-optic dipping liquid analyzer (FDLA) is developed for measuring liquid properties such as concentration, refractive index, surface tension, and viscosity. An important feature of the FDLA is that a liquid drop is introduced on the end face of a fiber probe, and the drop can be regarded as a planar-convex lens. The light transmitting path and receiving power are affected by the refractive index of the liquid drop. We present a theoretical and experimental analysis of the light transmission. A mathematical model of receiving power is established based on paraxial refraction imaging and fiber reflective intensity modulation methods. Sucrose-water solutions were tested with the FDLA. The experimental results agree well with the theoretical analysis.

The Value of the Freshwater Snail Dip Scoop Sampling Method in Macroinvertebrates Bioassessment of Sugar Mill Wastewater Pollution in Mbandjock, Cameroon

Directory of Open Access Journals (Sweden)

Emmanuel Noumi

2008-03-01

Full Text Available Macroinvertebrates identification and enumeration may be used as a simple and affordable alternative to chemical analysis in water pollution monitoring. However, the ecological responses of various taxa to pollution are poorly known in resources-limited tropical countries. While freshwater macroinvertebrates have been used in the assessment of water quality in Europe and the Americas, investigations in Africa have mainly focused on snail hosts of human parasites. There is a need for sampling methods that can be used to assess both snails and other macroinvertebrates. The present study was designed to evaluate the usefulness of the freshwater snail dip scoop method in the study of macroinvertebrates for the assessment of the SOSUCAM sugar mill effluents pollution. Standard snail dip scoop samples were collected upstream and downstream of the factory effluent inputs, on the Mokona and Mengoala rivers. The analysis of the macroinvertebrate communities revealed the absence of Ephemeroptera and Trichoptera, and the thriving of Syrphidae in the sections of the rivers under high effluent load. The Shannon and Weaver diversity index was lower in these areas. The dip scoop sampling protocol was found to be a useful method for macroinvertebrates collection. Hence, this method is recommended as a simple, cost-effective and efficient tool for the bio-assessment of freshwater pollution in developing countries with limited research resources.

How to Start with a Clean Crop: Biopesticide Dips Reduce Populations of Bemisia tabaci (Hemiptera: Aleyrodidae on Greenhouse Poinsettia Propagative Cuttings

Directory of Open Access Journals (Sweden)

Rosemarije Buitenhuis

2016-09-01

Full Text Available (1 Global movement of propagative plant material is a major pathway for introduction of Bemisia tabaci (Hemiptera: Aleyrodidae into poinsettia greenhouses. Starting a poinsettia crop with high pest numbers disrupts otherwise successful biological control programs and widespread resistance of B. tabaci against pesticides is limiting growers’ options to control this pest; (2 This study investigated the use of several biopesticides (mineral oil, insecticidal soap, Beauveria bassiana, Isaria fumosorosea, Steinernema feltiae and combinations of these products as immersion treatments (cutting dips to control B. tabaci on poinsettia cuttings. In addition, phytotoxicity risks of these treatments on poinsettia cuttings, and effects of treatment residues on mortality of commercial whitefly parasitoids (Eretmocerus eremicus and Encarsia formosa were determined; (3 Mineral oil (0.1% v/v and insecticidal soap (0.5% + B. bassiana (1.25 g/L were the most effective treatments; only 31% and 29%, respectively, of the treated B. tabaci survived on infested poinsettia cuttings and B. tabaci populations were lowest in these treatments after eight weeks. Phytotoxicity risks of these treatments were acceptable, and dip residues had little effect on survival of either parasitoid, and are considered highly compatible; (4 Use of poinsettia cutting dips will allow growers to knock-down B. tabaci populations to a point where they can be managed successfully thereafter with existing biocontrol strategies.

Theory of hot particle stability

International Nuclear Information System (INIS)

Berk, H.L.; Wong, H.V.; Tsang, K.T.

1986-10-01

The investigation of stabilization of hot particle drift reversed systems to low frequency modes has been extended to arbitrary hot beta, β/sub H/ for systems that have unfavorable field line curvature. We consider steep profile equilibria where the thickness of the pressure drop, Δ, is less than plasma radius, r/sub p/. The analysis describes layer modes which have mΔ/r/sub p/ 2/3. When robust stability conditions are fulfilled, the hot particles will have their axial bounce frequency less than their grad-B drift frequency. This allows for a low bounce frequency expansion to describe the axial dependence of the magnetic compressional response

An ALARA-conscious hot particle control program

International Nuclear Information System (INIS)

Doolittle, W.W.; Bredvad, R.S.; Bevelacqua, J.J.

1992-01-01

In 1989 approximately twenty-five percent of the radiation dose received by the Point Beach Nuclear Plant (PBNP) Health Physics group was due to its hot particle control program. The Health Physics group initiated a review of the program with the objective of decreasing the dose expenditure for hot particle control while maintaining a high standard for hot particle detection and control. In this paper the methods and results of this evaluation are described. The components of the hot particle control program, rules of thumb, and radionuclide composition at PBNP are presented

21 CFR 880.6085 - Hot/cold water bottle.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hot/cold water bottle. 880.6085 Section 880.6085... Devices § 880.6085 Hot/cold water bottle. (a) Identification. A hot/cold water bottle is a device intended for medical purposes that is in the form of a container intended to be filled with hot or cold water...

'Hot' particles in the atmosphere (Vilnius, 1986)

International Nuclear Information System (INIS)

Lujanas, V.; Shpirkauskaite, N.

1992-01-01

After the Chernobyl accident in the atmosphere above Vilnius the alpha-and beta- 'hot' particles were discovered. The amount of particles and their size were measured by the alpha-radiography. After the exposition of nuclear plates the 'auroras' of the beta hot particles were of the size 0.37-22.2 μm. The change in time of the beta- 'hot' particles amount in the ground level air from the 25th of April to the 9th of May, 1986 was given. The amount of this particles deposited in the adult man respiratory tract was calculated. The energy of the discovered 8 'hot' alpha-particles ranged from 4.2 to 6.6 MeV. All the samples in which alpha- 'hot' particles found were taken in anticyclone conditions. (author). 1 tab., 1 ref

Ormen Lange hot tap - a world record

Energy Technology Data Exchange (ETDEWEB)

Apeland, Kjell Edvard

2010-07-01

For the last 10 years Statoil have been developing a new concept for performing subsea Hot Tap operations remotely controlled. The system was first used offshore in 2008 during a partly diver assisted operation, connecting the Tampen Link pipeline to the Statfjord Intrafield pipeline. In July 2009, the Hot Tap System successfully performed two remotely controlled Hot Taps, on a world record depth of 860 meters on the Ormen Lange field operated by Shell. The Hot Tap technology enables existing pipeline architecture to be modified, without interfering with the current production. Most of the technology is depth independent and the system is currently qualified to 1000 meter depth. Phase II of this project which involves development and construction of a retrofit Tee, thus enabling installation and welding of a Tee on an unprepared pipeline is well underway. This presentation will describe experiences from the development of the Remote Hot Tap system and give an overview of the offshore operations leading to the conclusion of the world's deepest Hot Taps. (Author)

Simulation studies on stability of hot electron plasma

International Nuclear Information System (INIS)

Ohsawa, Yukiharu

1985-01-01

Stability of a hot electron plasma in an NBT(EBT)-like geometry is studied by using a 2-1/2 dimensional relativistic, electromagnetic particle code. For the low-frequency hot electron interchange mode, comparison of the simulation results with the analytical predictions of linear stability theory show fairly good agreement with the magnitude of the growth rates calculated without hot electron finite Larmor radius effects. Strong stabilizing effects by finite Larmor radius of the hot electrons are observed for short wavelength modes. As for the high-frequency hot electron interchange mode, there is a discrepancy between the simulation results and the theory. The high-frequency instability is not observed though a parameter regime is chosen in which the high-frequency hot electron interchange mode is theoretically predicted to grow. Strong cross-field diffusion in a poloidal direction of the hot electrons might explain the stability. Each particle has a magnetic drift velocity, and the speed of the magnetic drift is proportional to the kinetic energy of each particle. Hence, if the particles have high temperature, the spread of the magnetic drift velocity is large. This causes a strong cross-field diffusion of the hot electrons. In the simulation for this interchange mode, an enhanced temperature relaxation is observed between the hot and cold electrons although the theoretically predicted high frequency modes are stable. (Nogami, K.)

Archaeal Nitrification in Hot Springs

Science.gov (United States)

Richter, A.; Daims, H.; Reigstad, L.; Wanek, W.; Wagner, M.; Schleper, C.

2006-12-01

Biological nitrification, i.e. the aerobic conversion of ammonia to nitrate via nitrite, is a major component of the global nitrogen cycle. Until recently, it was thought that the ability to aerobically oxidize ammonia was confined to bacteria of the phylum Proteobacteria. However, it has recently been shown that Archaea of the phylum Crenarchaeota are also capable of ammonia oxidation. As many Crenarchaeota are thermophilic or hyperthermophilic, and at least some of them are capable of ammonia oxidation we speculated on the existence of (hyper)thermophilic ammonia-oxidizing archaea (AOA). Using PCR primers specifically targeting the archaeal ammonia monooxygenase (amoA) gene, we were indeed able to confirm the presence of such organisms in several hot springs in Reykjadalur, Iceland. These hot springs exhibited temperatures well above 80 °C and pH values ranging from 2.0 to 4.5. To proof that nitrification actually took place under these extreme conditions, we measured gross nitrification rates by the isotope pool dilution method; we added 15N-labelled nitrate to the mud and followed the dilution of the label by nitrate production from ammonium either in situ (incubation in the hot spring) or under controlled conditions in the laboratory (at 80 °C). The nitrification rates in the hot springs ranged from 0.79 to 2.22 mg nitrate-N per L of mud and day. Controls, in which microorganisms were killed before the incubations, demonstrated that the nitrification was of biological origin. Addition of ammonium increased the gross nitrification rate approximately 3-fold, indicating that the nitrification was ammonium limited under the conditions used. Collectively, our study provides evidence that (1) AOA are present in hot springs and (2) that they are actively nitrifying. These findings have major implications for our understanding of nitrogen cycling of hot environments.

Coulomb explosion of “hot spot”

Energy Technology Data Exchange (ETDEWEB)

Oreshkin, V. I., E-mail: oreshkin@ovpe.hcei.tsc.ru [Institute of High Current Electrons, SB, RAS, Tomsk (Russian Federation); Tomsk Polytechnic University, Tomsk (Russian Federation); Oreshkin, E. V. [P. N. Lebedev Physical Institute, RAS, Moscow (Russian Federation); Chaikovsky, S. A. [Institute of High Current Electrons, SB, RAS, Tomsk (Russian Federation); P. N. Lebedev Physical Institute, RAS, Moscow (Russian Federation); Institute of Electrophysics, UD, RAS, Ekaterinburg (Russian Federation); Artyomov, A. P. [Institute of High Current Electrons, SB, RAS, Tomsk (Russian Federation)

2016-09-15

The study presented in this paper has shown that the generation of hard x rays and high-energy ions, which are detected in pinch implosion experiments, may be associated with the Coulomb explosion of the hot spot that is formed due to the outflow of the material from the pinch cross point. During the process of material outflow, the temperature of the hot spot plasma increases, and conditions arise for the plasma electrons to become continuously accelerated. The runaway of electrons from the hot spot region results in the buildup of positive space charge in this region followed by a Coulomb explosion. The conditions for the hot spot plasma electrons to become continuously accelerated have been revealed, and the estimates have been obtained for the kinetic energy of the ions generated by the Coulomb explosion.

Coulomb explosion of “hot spot”

International Nuclear Information System (INIS)

Oreshkin, V. I.; Oreshkin, E. V.; Chaikovsky, S. A.; Artyomov, A. P.

2016-01-01

The study presented in this paper has shown that the generation of hard x rays and high-energy ions, which are detected in pinch implosion experiments, may be associated with the Coulomb explosion of the hot spot that is formed due to the outflow of the material from the pinch cross point. During the process of material outflow, the temperature of the hot spot plasma increases, and conditions arise for the plasma electrons to become continuously accelerated. The runaway of electrons from the hot spot region results in the buildup of positive space charge in this region followed by a Coulomb explosion. The conditions for the hot spot plasma electrons to become continuously accelerated have been revealed, and the estimates have been obtained for the kinetic energy of the ions generated by the Coulomb explosion.

Dip-in Indicators for Visual Differentiation of Fuel Mixtures Based on Wettability of Fluoroalkylchlorosilane-Coated Inverse Opal Films.

Science.gov (United States)

Sedighi, Abootaleb; Qiu, Shuang; Wong, Michael C K; Li, Paul C H

2015-12-30

We have developed the dip-in indicator based on the inverse opal film (IOF) for visual differentiation of organic liquid mixtures, such as oil/gasoline or ethanol/gasoline fuel mixtures. The IOF consists of a three-dimensional porous structure with a highly ordered periodic arrangement of nanopores. The specularly reflected light at the interface of the nanopores and silica walls contributes to the structural color of the IOF film. This color disappears when the nanopores are infiltrated by a liquid with a similar refractive index to silica. The disappearance of the structural color provides a means to differentiate various liquid fuel mixtures based on their wettability of the nanopores in the IOF-based indicators. For differentiation of various liquid mixtures, we tune the wettability threshold of the indicator in such a way that it is wetted (color disappears) by one liquid but is not wetted by the other (color remains). Although colorimetric differentiation of liquids based on IOF wettability has been reported, differentiation of highly similar liquid mixtures require complicated readout approaches. It is known that the IOF wettability is controlled by multiple surface properties (e.g., oleophobicity) and structural properties (e.g., neck angle and film thickness) of the nanostructure. Therefore, we aim to exploit the combined tuning of these properties for differentiation of fuel mixtures with close compositions. In this study, we have demonstrated that, for the first time, the IOF-based dip-in indicator is able to detect a slight difference in the fuel mixture composition (i.e., 0.4% of oil content). Moreover, the color/no-color differentiation platform is simple, powerful, and easy-to-read. This platform makes the dip-in indicator a promising tool for authentication and determination of fuel composition at the point-of-purchase or point-of-use.

A study of pressureless microwave sintering, microwave-assisted hot press sintering and conventional hot pressing on properties of aluminium/alumina nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Abedinzadeh, Reza; Safavi, Seyed Mohsen; Karimzadeh, Fathallah [Isfahan University, Isfahan (Iran, Islamic Republic of)

2016-05-15

Bulk Al/4wt-%Al{sub 2}O{sub 3} nanocomposites were prepared by consolidating nanocomposite powders using pressureless microwave sintering, microwave-assisted hot press sintering and conventional hot pressing techniques. Microstructural observations revealed that the microwave-assisted hot press sintering at different sintering temperatures of 400.deg.C and 500.deg.C resulted in more densification and smaller grain size for Al/Al{sub 2}O{sub 3} nanocomposite as compared with the conventional hot pressing. Moreover, the application of pressure in microwave sintering process led to more densification and grain growth. Mechanical properties resulting from microhardness and nanoindentation tests were also compared between three-method processed samples. It was found that the microwave-assisted hot-pressed sample exhibited higher hardness and elastic modulus in comparison with microwave-sintered and conventional hot-pressed samples. The improvement in the mechanical properties can be ascribed to lower porosity of microwave-assisted hot-pressed sample.

Lorenz curve and Gini coefficient reveal hot spots and hot moments for nitrous oxide emissions

Science.gov (United States)

Identifying hot spots and hot moments of N2O emissions in the landscape is critical for monitoring and mitigating the emission of this powerful greenhouse gas. We propose a novel use of the Lorenz curve and Gini coefficient (G) to quantify the heterogeneous distribution of N2O emissions from a lands...

Hot Flashes amd Night Sweats (PDQ)

Science.gov (United States)

... Professionals Questions to Ask about Your Treatment Research Hot Flashes and Night Sweats (PDQ®)–Patient Version Overview ... quality of life in many patients with cancer. Hot flashes and night sweats may be side effects ...

Fabrication of silica ceramic membrane via sol-gel dip-coating method at different nitric acid amount

Science.gov (United States)

Kahlib, N. A. Z.; Daud, F. D. M.; Mel, M.; Hairin, A. L. N.; Azhar, A. Z. A.; Hassan, N. A.

2018-01-01

Fabrication of silica ceramics via the sol-gel method has offered more advantages over other methods in the fabrication of ceramic membrane, such as simple operation, high purity homogeneous, well defined-structure and complex shapes of end products. This work presents the fabrication of silica ceramic membrane via sol-gel dip-coating methods by varying nitric acid amount. The nitric acid plays an important role as catalyst in fabrication reaction which involved hydrolysis and condensation process. The tubular ceramic support, used as the substrate, was dipped into the sol of Tetrethylorthosilicate (TEOS), distilled water and ethanol with the addition of nitric acid. The fabricated silica membrane was then characterized by (Field Emission Scanning Electron Microscope) FESEM and (Fourier transform infrared spectroscopy) FTIR to determine structural and chemical properties at different amount of acids. From the XRD analysis, the fabricated silica ceramic membrane showed the existence of silicate hydrate in the final product. FESEM images indicated that the silica ceramic membrane has been deposited on the tubular ceramic support as a substrate and penetrate into the pore walls. The intensity peak of FTIR decreased with increasing of amount of acids. Hence, the 8 ml of acid has demonstrated the appropriate amount of catalyst in fabricating good physical and chemical characteristic of silica ceramic membrane.

Hot-dipped tin-zinc on U-0.75 w/o Ti

International Nuclear Information System (INIS)

Weirick, L.J.

1979-09-01

Conventional Zn galvanizing of U-0.75 Ti results in nonuniform coatings and reduced elongation because of thermal aging of the surface of the U-Ti. A lower melting material which would give sacrificial galvanic protection to the U-Ti was found in the Sn-Zn alloy system. The present work describes: (1) the metallography of the Sn-Zn system, (2) the electrochemistry of the Sn-Zn system with respect to U-Ti, (3) the mechanics of applying a Sn-Zn coating to U-Ti, (4) salt spray corrosion test results of various Sn-Zn alloys applied to U-Ti coupons, and (5) mechanical property tests of coated U-Ti tensile bars. An 80 Sn-20 Zn alloy (MP-280 0 C) was chosen for the galvanizing study because of its lower melting point. The results showed that all alloys of the Sn-Zn system galvanically protected the U-Ti in salt fog environments. The lack of a suitable low temperature flux prevented the operation of the Sn-Zn bath at its optimum temperature and low elongations were obtained with this coating system

Investigation of shinning Spot Defect on Hot-Dip Galvanized Steel Sheets

International Nuclear Information System (INIS)

Yonggang, Liu; Lei, Cui

2014-01-01

Shinning spot defects on galvanized steel sheets were studied by optical microscope, scanning electron microscope(SEM), Energy Dispersive Spectrometer (EDS) and Laser-Induced Breakdown Spectroscopy Original Position Statistic Distribution Analysis (LIBSOPA) in this study. The research shows that the coating thickness of shinning spot defects which caused by the substrate defect is much lower than normal area, and when skin passed, the shinning spot defect area can not touch with skin pass roll which result in the surface of shinning spot is flat while normal area is rough. The different coating morphologies have different effects on the reflection of light, which cause the shinning spot defects more brighter than normal area

7 CFR 305.21 - Hot water dip treatment schedule for mangoes.

Science.gov (United States)

2010-01-01

..., Margarita, Tortuga, or Trinidad and Tobago) Flat, elongated varieties Up to 400400-570 6575 Rounded... Panama, South America, or West Indies islands of Aruba, Bonaire, Curacao, Margarita, Tortuga, or Trinidad...

Hot deformation behavior and hot working characteristic of Nickel-base electron beam weldments

International Nuclear Information System (INIS)

Ning, Yongquan; Yao, Zekun; Guo, Hongzhen; Fu, M.W.

2014-01-01

Highlights: • The Hot deformation behavior of electron beam (EB) Nickel-base weldments was investigated. • The constitutive equation represented by temperature, strain rate and true strain was developed. • Processing map approach was adopted to optimize the hot forging process of EB weldments. • True strain has a great effect on the efficiency of power dissipation (η). -- Abstract: The electron beam welding (EBW) of Nickel-base superalloys was conducted, and the cylindrical compression specimens were machined from the central part of the electron beam (EB) weldments. The hot deformation behavior of EB weldments was investigated at the temperature of 960–1140 °C and the strain rate of 0.001–1.0 s −1 . The apparent activation energy of deformation was calculated to be 400 kJ/mol, and the constitutive equation that describes the flow stress as a function of strain rate and deformation temperature was proposed for modeling of the hot deformation process of EB weldments. The processing map approach was adopted to investigate the deformation mechanisms during the hot plastic deformation and to optimize the processing parameters of EB weldments. It is found that the true strain has a significant effect on the efficiency of power dissipation (η). The η value in the safe processing domain (1140 °C, 1.0 s −1 ) increases from 0.32 to 0.55. In the unsafe processing domain (1080 °C, 0.001 s −1 ), however, the η value greatly decreases with the increase of strain. When the strain is 0.40, the efficiency of power dissipation becomes negative. The flow instability is predicted to occur since the instability parameter ξ(ε) becomes negative. The hot deformation of EB weldments can be carried out safely in the domain with the strain rate range of 0.1–1.0 s −1 and the temperature range of 960–1140 °C. When the height reduction is about 50%, the optimum processing condition is (T opi : 1140 °C, ε opi : 1.0 s −1 ) with the peak efficiency of 0

Hot deformation behavior and hot working characteristic of Nickel-base electron beam weldments

Energy Technology Data Exchange (ETDEWEB)

Ning, Yongquan, E-mail: ningke521@163.com [School of Materials Science and Engineering, Northwestern Polytechnical University, Xi’an 710072 (China); Yao, Zekun; Guo, Hongzhen [School of Materials Science and Engineering, Northwestern Polytechnical University, Xi’an 710072 (China); Fu, M.W. [Department of Mechanical Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong (China)

2014-01-25

Highlights: • The Hot deformation behavior of electron beam (EB) Nickel-base weldments was investigated. • The constitutive equation represented by temperature, strain rate and true strain was developed. • Processing map approach was adopted to optimize the hot forging process of EB weldments. • True strain has a great effect on the efficiency of power dissipation (η). -- Abstract: The electron beam welding (EBW) of Nickel-base superalloys was conducted, and the cylindrical compression specimens were machined from the central part of the electron beam (EB) weldments. The hot deformation behavior of EB weldments was investigated at the temperature of 960–1140 °C and the strain rate of 0.001–1.0 s{sup −1}. The apparent activation energy of deformation was calculated to be 400 kJ/mol, and the constitutive equation that describes the flow stress as a function of strain rate and deformation temperature was proposed for modeling of the hot deformation process of EB weldments. The processing map approach was adopted to investigate the deformation mechanisms during the hot plastic deformation and to optimize the processing parameters of EB weldments. It is found that the true strain has a significant effect on the efficiency of power dissipation (η). The η value in the safe processing domain (1140 °C, 1.0 s{sup −1}) increases from 0.32 to 0.55. In the unsafe processing domain (1080 °C, 0.001 s{sup −1}), however, the η value greatly decreases with the increase of strain. When the strain is 0.40, the efficiency of power dissipation becomes negative. The flow instability is predicted to occur since the instability parameter ξ(ε) becomes negative. The hot deformation of EB weldments can be carried out safely in the domain with the strain rate range of 0.1–1.0 s{sup −1} and the temperature range of 960–1140 °C. When the height reduction is about 50%, the optimum processing condition is (T{sub opi}: 1140 °C, ε{sub opi}: 1.0 s{sup −1}) with

Detecting hot spots at hazardous-waste sites

International Nuclear Information System (INIS)

Zirschky, J.; Gilbert, R.O.

1984-01-01

Evaluating the need for remedial cleanup at a waste site involves both finding the average contaminant concentration and identifying highly contaminated areas, or hot spots. A nomographic procedure to determine the sample configuration needed to locate a hot spot is presented. The technique can be used to develop a waste-site sampling plant - to determine either the grid spacing required to detect a hot spot at a given level of confidence, or the probability of finding a hot spot of a certain size, given a particular grid spacing. The method and computer program (ELIPGRID) were developed for locating geologic deposits, but the basic procedure can also be used to detect hot spots at chemical- or nuclear-waste disposal sites. Nomographs based on the original program are presented for three sampling-grid configurations - square, rectangular and triangular

HOT GAS HALOS IN EARLY-TYPE FIELD GALAXIES

International Nuclear Information System (INIS)

Mulchaey, John S.; Jeltema, Tesla E.

2010-01-01

We use Chandra and XMM-Newton to study the hot gas content in a sample of field early-type galaxies. We find that the L X -L K relationship is steeper for field galaxies than for comparable galaxies in groups and clusters. The low hot gas content of field galaxies with L K ∼ * suggests that internal processes such as supernovae-driven winds or active galactic nucleus feedback expel hot gas from low-mass galaxies. Such mechanisms may be less effective in groups and clusters where the presence of an intragroup or intracluster medium can confine outflowing material. In addition, galaxies in groups and clusters may be able to accrete gas from the ambient medium. While there is a population of L K ∼ * galaxies in groups and clusters that retain hot gas halos, some galaxies in these rich environments, including brighter galaxies, are largely devoid of hot gas. In these cases, the hot gas halos have likely been removed via ram pressure stripping. This suggests a very complex interplay between the intragroup/intracluster medium and hot gas halos of galaxies in rich environments, with the ambient medium helping to confine or even enhance the halos in some cases and acting to remove gas in others. In contrast, the hot gas content of more isolated galaxies is largely a function of the mass of the galaxy, with more massive galaxies able to maintain their halos, while in lower mass systems the hot gas escapes in outflowing winds.

Effect of hot pressing additives on the leachability of hot pressed sodium hydrous titanium oxide

International Nuclear Information System (INIS)

Valentine, T.M.; Sambell, R.A.J.

1980-01-01

Sodium hydrous titanium oxide is an ion exchange resin which can be used for immobilizing medium level waste (MLW) liquors. When hot pressed, it undergoes conversion to a ceramic. Three low melting point materials (borax, bismuth trioxide, and a mixture of PbO/CuO) were added to the (Na)HTiO and the effect that each of these had on aiding densification was assessed. Hot pressing temperature, applied pressure, and percentage addition of hot pressing aid were varied. Percentage open porosity, flexural strength, and leachability were measured. There was a linear relationship between the percentage open porosity and the logarithm of the leach rate for a constant percentage addition of each additive

Hot laboratory in Saclay. Equipment and radio-metallurgy technique of the hot lab in Saclay. Description of hot cell for handling of plutonium salts. Installation of an hot cell

International Nuclear Information System (INIS)

Bazire, R.; Blin, J.; Cherel, G.; Duvaux, Y.; Cherel, G.; Mustelier, J.P.; Bussy, P.; Gondal, G.; Bloch, J.; Faugeras, P.; Raggenbass, A.; Raggenbass, P.; Fufresne, J.

1959-01-01

Describes the conception and installation of the hot laboratory in Saclay (CEA, France). The construction ended in 1958. The main aim of this laboratory is to examine fuel rods of EL2 and EL3 as well as nuclear fuel studies. It is placed in between both reactors. In a first part, the functioning and specifications of the hot lab are given. The different hot cells are described with details of the ventilation and filtration system as well as the waste material and effluents disposal. The different safety measures are explained: description of the radiation protection, decontamination room and personnel monitoring. The remote handling equipment is composed of cutting and welding machine controlled with manipulators. Periscopes are used for sight control of the operation. In a second part, it describes the equipment of the hot lab. The unit for an accurate measurement of the density of irradiated uranium is equipped with an high precision balance and a thermostat. The equipment used for the working of irradiated uranium is described and the time length of each operation is given. There is also an installation for metallographic studies which is equipped with a manipulation bench for polishing and cleaning surfaces and a metallographic microscope. X-ray examination of uranium pellets will also be made and results will be compared with those of metallography. The last part describes the hot cells used for the manipulation of plutonium salts. The plutonium comes from the reprocessing plant and arrived as a nitric solution. Thus these cells are used to study the preparation of plutonium fluorides from nitric solution. The successive operations needed are explained: filtration, decontamination and extraction with TBP, purification on ion exchangers and finally formation of the plutonium fluorides. Particular attention has been given to the description of the specifications of the different gloveboxes and remote handling equipment used in the different reaction steps and

Advanced cold rolled steels for automotive applications

Energy Technology Data Exchange (ETDEWEB)

Hofmann, Harald; Mattissen, Dorothea; Schaumann, Thomas Wilhelm [ThyssenKrupp Steel AG, Center of Materials Excellence, Dortmund (Germany)

2009-01-15

Advanced high-strength steels offer a great potential for the further development of automobile bodies-in-white due to their combined mechanical properties of high formability and strength. They represent the first choice in material selection for strength and crash-relevant parts with challenging geometries. The intensive development of multiphase steels by ThyssenKrupp Steel has led to hot dip galvanizing concepts with an outstanding forming potential. Hot rolled, hot dip galvanized complex-phase steels are currently produced in addition to cold rolled dual phase (DP) and retained austenite (RA) or transformation induced plasticity (TRIP) steels. New continuously annealed grades of steel are being developed with tensile strength levels of up to 1000 MPa in combination with sufficient ductility for the high demands of structural automobile components. These steels make use of the classic advantages of microalloying as well as the principles of DP steels and RA / TRIP steels. Further improvement of properties will be reached by the new class of high manganese alloyed steels. (orig.)

Optical pumping-assisted electromagnetically induced transparency

International Nuclear Information System (INIS)

Jiang Wei; Chen Qunfeng; Zhang Yongsheng; Guo, G.-C.

2006-01-01

In this paper we report an observation of the two-photon absorption in a four-level system in hot 87 Rb vapor based on the proposal of Harris and Yamamoto [Phys. Rev. Lett. 81, 3611 (1998)]. We show that this effect is reduced in hot atoms due to the non-Doppler-free nature of this scheme. Then we report a phenomenon that could be used in the same application of Harris and Yamamoto. The main result is a great enhancement of electromagnetically induced transparency (EIT) effect in hot 87 Rb vapor caused by optical pumping. We find that when the single photon detuning is near zero the EIT signal is dramatically enhanced by an optical pumping field. More interestingly when the single photon detuning is larger the signal can be changed from a sharp Raman peak to a sharp EIT dip. The full width at half maximum of the peak and dip are narrow and subnatural

Nocturnal antihypertensive treatment in patients with type 1 diabetes with autonomic neuropathy and non-dipping of blood pressure during night time

DEFF Research Database (Denmark)

Hjortkær, Henrik; Jensen, Tonny; Kofoed, Klaus

2014-01-01

INTRODUCTION: Cardiac autonomic neuropathy (CAN) and elevated nocturnal blood pressure are independent risk factors for cardiovascular disease in patients with diabetes. Previously, associations between CAN, non-dipping of nocturnal blood pressure and coronary artery calcification have been...

Characterization for rbs of Titanium Oxide thin films grown by Dip Coating in a coloidal suspension of nano structured Titanium Oxide

International Nuclear Information System (INIS)

Pedrero, E.; Vigil, E.; Zumeta, I.

1999-01-01

The depth of Titanium Oxide thin films grown by Dip Coating in a coloidal suspension of nano structured Titanium Oxide was characterized using Rutherford Backscattering Spectrometry. Film depths are compared in function of bath and suspension parameters

Dip-pen nanopatterning of photosensitive conducting polymer using a monomer ink

Science.gov (United States)

Su, Ming; Aslam, Mohammed; Fu, Lei; Wu, Nianqiang; Dravid, Vinayak P.

2004-05-01

Controlled patterning of conducting polymers at a micro- or nanoscale is the first step towards the fabrication of miniaturized functional devices. Here, we introduce an approach for the nanopatterning of conducting polymers using an improved monomer "ink" in dip-pen nanolithography (DPN). The nominal monomer "ink" is converted, in situ, to its conducting solid-state polymeric form after patterned. Proof-of-concept experiments have been performed with acid-promoted polymerization of pyrrole in a less reactive environment (tetrahydrofuran). The ratios of reactants are optimized to give an appropriate rate to match the operation of DPN. A similar synthesis process for the same polymer in its bulk form shows a high conductance and crystalline structure. The miniaturized conducting polymer sensors with light detection ability are fabricated by DPN using the improved ink formula, and exhibit excellent response, recovery, and sensitivity parameters.

Dip-pen nanopatterning of photosensitive conducting polymer using a monomer ink

International Nuclear Information System (INIS)

Su Ming; Aslam, Mohammed; Fu Lei; Wu Nianqiang; Dravid, Vinayak P.

2004-01-01

Controlled patterning of conducting polymers at a micro- or nanoscale is the first step towards the fabrication of miniaturized functional devices. Here, we introduce an approach for the nanopatterning of conducting polymers using an improved monomer 'ink' in dip-pen nanolithography (DPN). The nominal monomer 'ink' is converted, in situ, to its conducting solid-state polymeric form after patterned. Proof-of-concept experiments have been performed with acid-promoted polymerization of pyrrole in a less reactive environment (tetrahydrofuran). The ratios of reactants are optimized to give an appropriate rate to match the operation of DPN. A similar synthesis process for the same polymer in its bulk form shows a high conductance and crystalline structure. The miniaturized conducting polymer sensors with light detection ability are fabricated by DPN using the improved ink formula, and exhibit excellent response, recovery, and sensitivity parameters

Graphene and water-based elastomers thin-film composites by dip-moulding.

Science.gov (United States)

Iliut, Maria; Silva, Claudio; Herrick, Scott; McGlothlin, Mark; Vijayaraghavan, Aravind

2016-09-01

Thin-film elastomers (elastic polymers) have a number of technologically significant applications ranging from sportswear to medical devices. In this work, we demonstrate that graphene can be used to reinforce 20 micron thin elastomer films, resulting in over 50% increase in elastic modulus at a very low loading of 0.1 wt%, while also increasing the elongation to failure. This loading is below the percolation threshold for electrical conductivity. We demonstrate composites with both graphene oxide and reduced graphene oxide, the reduction being undertaken in-situ or ex-situ using a biocompatible reducing agent in ascorbic acid. The ultrathin films were cast by dip moulding. The transparency of the elastomer films allows us to use optical microscopy image and confirm the uniform distribution as well as the conformation of the graphene flakes within the composite.

Formation and decay of hot nuclei

International Nuclear Information System (INIS)

Tamain, B.

1992-09-01

The mechanisms involved in hot nuclei formation and decay and their eventual connexion with fundamental properties of nuclear matter are discussed, i.e. its equation of state is considered. After a brief review of the reactions in which hot nuclei can be formed, the variables which are used to describe them, the corresponding theoretical descriptions and their limits when extreme states are reached are discussed. Experimental evidences for hot nuclei formation are presented, with the corresponding decay properties used as signatures. (R.P.) 64 refs.; 25 figs.; 2 tabs