Efficient Implementation of Ternary SDM Filters using State-of-the-Art FPGA

Directory of Open Access Journals (Sweden)

Tayabuddin Memon

2011-04-01

Full Text Available We present the analysis of a ternary FIR filter at varying OSR (Over Sampling Ratios. The sigma delta modulated ternary filter impulse responses obtained using Matlab at varying OSRs show that each doubling of OSR results in an increase of 10dB in the stopband attenuation. BT-FIR (Balanced Ternary FIR Filters at varying OSRs have been implemented in VHDL using an efficient adder tree organization to gather the partial products. Filters in both pipelined and non-pipelined modes were synthesized on a small number of representative commercial FPGA (Field Programmable Gate Arrays devices. Both the filter taps and binary inputs use 2\\'s complement format. The synthesis results show the tradeoffs between hardware area and performance at varying OSRs. In pipelined mode, a 6MHz video stream can easily be handled at an OSR of 64, while occupying less than 8% of a Stratix-III device.

Ternary Blend Composed of Two Organic Donors and One Acceptor for Active Layer of High-Performance Organic Solar Cells.

Science.gov (United States)

Lee, Jong Won; Choi, Yoon Suk; Ahn, Hyungju; Jo, Won Ho

2016-05-04

Ternary blends composed of two donor absorbers with complementary absorptions provide an opportunity to enhance the short-circuit current and thus the power conversion efficiency (PCE) of organic solar cells. In addition to complementary absorption of two donors, ternary blends may exhibit favorable morphology for high-performance solar cells when one chooses properly the donor pair. For this purpose, we develop a ternary blend with two donors (diketopyrrolopyrrole-based polymer (PTDPP2T) and small molecule ((TDPP)2Ph)) and one acceptor (PC71BM). The solar cell made of a ternary blend with 10 wt % (TDPP)2Ph exhibits higher PCE of 7.49% as compared with the solar cells with binary blends, PTDPP2T:PC71BM (6.58%) and (TDPP)2Ph:PC71BM (3.21%). The higher PCE of the ternary blend solar cell is attributed mainly to complementary absorption of two donors. However, a further increase in (TDPP)2Ph content in the ternary blend (>10 wt %) decreases the PCE. The ternary blend with 10 wt % (TDPP)2Ph exhibits well-developed morphology with narrow-sized fibrils while the blend with 15 wt % (TDPP)2Ph shows phase separation with large-sized domains, demonstrating that the phase morphology and compatibility of ternary blend are important factors to achieve a high-performance solar cell made of ternary blends.

Feasibility survey on international cooperation for high efficiency energy conversion technology in fiscal 1993

Science.gov (United States)

1994-03-01

Following cooperative researches on fuel cell jointly conducted by NEDO and EGAT (Electricity Generating Authority of Thailand), the survey on international cooperation relating to high efficiency energy conversion technology was carried out for the ASEAN countries. The paper summed up the results of the survey. The study of the international cooperation is made for the following three items: a program for periodical exchange of information with EGAT, a project for cooperative research on phosphoric acid fuel cell in Indonesia, and a project for cooperative research with EGAT on electric power storage by advanced battery. In Malaysia, which is small in scale of state, part of the Ministry of Energy, Telecommunication and Posts is only in charge of the energy issue. Therefore, the situation is that they cannot answer well to many items of research/development cooperation brought in from Japan. The item of medium- and long-term developmental research in the Philippines is about the problems which are seen subsequently in the Manila metropolitan area where the problem of outage is being settled. Accordingly, it is essential to promote the cooperative research, well confirming policies and systems of the Ministry of Energy and the national electricity corporation.

Ternary superconductors

International Nuclear Information System (INIS)

Giorgi, A.L.

1987-01-01

Ternary superconductors constitute a class of superconducting compounds with exceptional properties such as high transition temperatures (≅ 15.2 K), extremely high critical fields (H c2 >60 Tesla), and the coexistence of superconductivity and long-range magnetic order. This has generated great interest in the scientific community and resulted in a large number of experimental and theoretical investigations in which many new ternary compounds have been discovered. A review of some of the properties of these ternary compounds is presented with particular emphasis on the ternary molybdenum chalcogenides and the ternary rare earth transition metal tetraborides. The effect of partial substitution of a second metal atom to form pseudoternary compounds is examined as well as some of the proposed correlations between the superconducting transition temperature and the structural and electronic properties of the ternary superconductors

Indacenodithienothiophene-Based Ternary Organic Solar Cells

Energy Technology Data Exchange (ETDEWEB)

Gasparini, Nicola, E-mail: nicola.gasparini@fau.de [Institute of Materials for Electronics and Energy Technology (I-MEET), Friedrich-Alexander-University Erlangen-Nuremberg, Erlangen (Germany); García-Rodríguez, Amaranda [Macromolecular Chemistry Group (buwmakro), Institute for Polymer Technology, BergischeUniversität Wuppertal, Wuppertal (Germany); Prosa, Mario [Istituto per lo Studio dei Materiali Nanostrutturati (ISMN), Consiglio Nazionale delle Ricerche (CNR), Bologna (Italy); Bayseç, Şebnem; Palma-Cando, Alex [Macromolecular Chemistry Group (buwmakro), Institute for Polymer Technology, BergischeUniversität Wuppertal, Wuppertal (Germany); Katsouras, Athanasios; Avgeropoulos, Apostolos [Department of Materials Science Engineering, University of Ioannina, Ioannina (Greece); Pagona, Georgia; Gregoriou, Vasilis G. [Advent Technologies SA, Patras Science Park, Patra (Greece); National Hellenic Research Foundation (NHRF), Athens (Greece); Chochos, Christos L. [Department of Materials Science Engineering, University of Ioannina, Ioannina (Greece); Advent Technologies SA, Patras Science Park, Patra (Greece); Allard, Sybille; Scherf, Ulrich [Macromolecular Chemistry Group (buwmakro), Institute for Polymer Technology, BergischeUniversität Wuppertal, Wuppertal (Germany); Brabec, Christoph J. [Institute of Materials for Electronics and Energy Technology (I-MEET), Friedrich-Alexander-University Erlangen-Nuremberg, Erlangen (Germany); Bavarian Center for Applied Energy Research (ZAE Bayern), Erlangen (Germany); Ameri, Tayebeh, E-mail: nicola.gasparini@fau.de [Institute of Materials for Electronics and Energy Technology (I-MEET), Friedrich-Alexander-University Erlangen-Nuremberg, Erlangen (Germany)

2017-01-13

One of the key aspects to achieve high efficiency in ternary bulk-hetorojunction solar cells is the physical and chemical compatibility between the donor materials. Here, we report the synthesis of a novel conjugated polymer (P1) containing alternating pyridyl[2,1,3]thiadiazole between two different donor fragments, dithienosilole and indacenodithienothiophene (IDTT), used as a sensitizer in a host system of indacenodithieno[3,2-b]thiophene,2,3-bis(3-(octyloxy)phenyl)quinoxaline (PIDTTQ) and [6,6]-phenyl C{sub 70} butyric acid methyl ester (PC{sub 71}BM). We found that the use of the same IDTT unit in the host and guest materials does not lead to significant changes in the morphology of the ternary blend compared to the host binary. With the complementary use of optoelectronic characterizations, we found that the ternary cells suffer from a lower mobility-lifetime (μτ) product, adversely impacting the fill factor. However, the significant light harvesting in the near infrared region improvement, compensating the transport losses, results in an overall power conversion efficiency enhancement of ~7% for ternary blends as compared to the PIDTTQ:PC{sub 71}BM devices.

Non-transboundary pollution and the efficiency of international environmental co-operation

International Nuclear Information System (INIS)

Kox, Henk L.M.; Van der Tak, Casper M.

1996-01-01

The standard view is that situations where no transborder environmental externalities occur are most efficiently dealt with by national environmental policies rather than by international co-operation. Though this may be the general case, non-coordinated national policies do not always produce the most efficient international allocation. This paper presents four cases in which the allocative outcome of non-coordinated domestic policy choices can be improved upon by international environmental co-operation. The first case refers to the use of environmental policy as a strategic trade instrument. The other cases refer to the existence of discrete technologies, set-up costs and increasing returns to scale. The form of international environmental co-operation should be adapted to the situation. Formal international agreements between countries are characterised by high transaction costs and may not always be the most efficient form of co-operation

Ternary Nonfullerene Polymer Solar Cells with 12.16% Efficiency by Introducing One Acceptor with Cascading Energy Level and Complementary Absorption.

Science.gov (United States)

Jiang, Weigang; Yu, Runnan; Liu, Zhiyang; Peng, Ruixiang; Mi, Dongbo; Hong, Ling; Wei, Qiang; Hou, Jianhui; Kuang, Yongbo; Ge, Ziyi

2018-01-01

A novel small-molecule acceptor, (2,2'-((5E,5'E)-5,5'-((5,5'-(4,4,9,9-tetrakis(5-hexylthiophen-2-yl)-4,9-dihydro-s-indaceno[1,2-b:5,6-b']dithiophene-2,7-diyl)bis(4-(2-ethylhexyl)thiophene-5,2-diyl))bis(methanylylidene)) bis(3-hexyl-4-oxothiazolidine-5,2-diylidene))dimalononitrile (ITCN), end-capped with electron-deficient 2-(3-hexyl-4-oxothiazolidin-2-ylidene)malononitrile groups, is designed, synthesized, and used as the third component in fullerene-free ternary polymer solar cells (PSCs). The cascaded energy-level structure enabled by the newly designed acceptor is beneficial to the carrier transport and separation. Meanwhile, the three materials show a complementary absorption in the visible region, resulting in efficient light harvesting. Hence, the PBDB-T:ITCN:IT-M ternary PSCs possess a high short-circuit current density (J sc ) under an optimal weight ratio of donors and acceptors. Moreover, the open-circuit voltage (V oc ) of the ternary PSCs is enhanced with an increase of the third acceptor ITCN content, which is attributed to the higher lowest unoccupied molecular orbital energy level of ITCN than that of IT-M, thus exhibits a higher V oc in PBDB-T:ITCN binary system. Ultimately, the ternary PSCs achieve a power conversion efficiency of 12.16%, which is higher than the PBDB-T:ITM-based PSCs (10.89%) and PBDB-T:ITCN-based ones (2.21%). This work provides an effective strategy to improve the photovoltaic performance of PSCs. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Energy efficiency: From regional to global cooperation

International Nuclear Information System (INIS)

Brendow, K.

1994-01-01

In developing, reforming and emerging countries in particular, institutional hurdles have hindered the introduction of energy efficient technology. The author develops the theme from two U.N. projects: A new institutional accessibility to supra-regional cooperation could provide an important stimulus for future worldwide cooperation in the field of energy efficiency. (orig.) [de

Development of an International Electric Cooperative Initiative on Energy Efficiency

Energy Technology Data Exchange (ETDEWEB)

Paul Clark; David South

2004-05-01

NRECA conceived of the International Electric Cooperative Initiative on Energy Efficiency (IECIEE) in order to provide an ongoing means of contributing voluntary actions on greenhouse gas emissions mitigation as an integral component of its international programs and projects. This required designing the IECIEE to be integrated directly with the core interests and attributes of participating cooperatives in the U.S. and Latin America, which was the initial focus area selected for the IECIEE. In the case of NRECA International, the core interests related to promoting and strengthening the electric cooperative model, which has proved highly successful in maximizing operational efficiencies in electric power generation, distribution and retailing, as compared to government-owned entities. The approach involved three basic components: (i) establishing the IECIEE mechanism, which involved setting up a functioning organizational vehicle providing for investment, management, and emissions credit accounting; (ii) developing a portfolio of projects in countries where NRECA International could effectively implement the broader mandate of cooperative development as energy efficient suppliers and distributors of electrical energy; and (iii) conducting outreach to obtain the commitment of participants and resources from U.S. and Latin American cooperatives and partnering agencies in the development financing community.

Superconductivity of ternary metal compounds prepared at high pressures

CERN Document Server

Shirotani, I

2003-01-01

Various ternary metal phosphides, arsenides, antimonides, silicides and germanides have been prepared at high temperatures and high pressures. These ternary metal compounds can be classified into four groups: [1] metal-rich compounds MM' sub 4 X sub 2 and [2] MM'X, [3] non-metal-rich compounds MXX' and [4] MM' sub 4 X sub 1 sub 2 (M and M' = metal element; X and X' = non-metal element). We have studied the electrical and magnetic properties of these materials at low temperatures, and found many new superconductors with the superconducting transition temperature (T sub c) of above 10 K. The metal-rich compound ZrRu sub 4 P sub 2 with a tetragonal structure showed the superconducting transition at around 11 K, and had an upper critical field (H sub c sub 2) of 12.2 tesla (T) at 0 K. Ternary equiatomic compounds ZrRuP and ZrRuSi crystallize in two modifications, a hexagonal Fe sub 2 P-type structure [h-ZrRuP(Si)] and an orthorhombic Co sub 2 P-type structure [o-ZrRuP(Si)]. Both h-ZrRuP and h-ZrRuSi have rather h...

Ternary complex of plasmid DNA with NLS-Mu-Mu protein and cationic niosome for biocompatible and efficient gene delivery: a comparative study with protamine and lipofectamine.

Science.gov (United States)

Nematollahi, Mohammad Hadi; Torkzadeh-Mahanai, Masoud; Pardakhty, Abbas; Ebrahimi Meimand, Hossein Ali; Asadikaram, Gholamreza

2017-10-28

Non-viral gene delivery methods are considered due to safety and simplicity in human gene therapy. Since the use of cationic peptide and niosome represent a promising approach for gene delivery purposes we used recombinant fusion protein and cationic niosome as a gene carrier. A multi-domain fusion protein including nuclear localization motif (NLS) and two DNA-binding (Mu) domains, namely NLS-Mu-Mu (NMM) has been designed, cloned and expressed in E. coli DE3 strain. Afterward, the interested protein was purified by affinity chromatography. Binary vectors based on protein/DNA and ternary vectors based on protein/DNA/niosome were prepared. Protamine was used as a control. DNA condensing properties of NMM and protamine were evaluated by various experiments. Furthermore, we examined cytotoxicity, hemolysis and transfection potential of the binary and ternary complexes in HEK293T and MCF-7 cell lines. Protamine and Lipofectamine™2000 were used as positive controls, correspondingly. The recombinant NMM was expressed and purified successfully and DNA was condensed efficiently at charge ratios that were not harmful to cells. Peptidoplexes showed transfection efficiency (TE) but ternary complexes had higher TE. Additionally, NMM ternary complex was more efficient compared to protamine ternary vectors. Our results showed that niosomal ternary vector of NMM is a promising non-viral gene carrier to achieve an effective and safe carrier system for gene therapy.

Design and synthesis of hierarchical MnO2 nanospheres/carbon nanotubes/conducting polymer ternary composite for high performance electrochemical electrodes.

Science.gov (United States)

Hou, Ye; Cheng, Yingwen; Hobson, Tyler; Liu, Jie

2010-07-14

For efficient use of metal oxides, such as MnO(2) and RuO(2), in pseudocapacitors and other electrochemical applications, the poor conductivity of the metal oxide is a major problem. To tackle the problem, we have designed a ternary nanocomposite film composed of metal oxide (MnO(2)), carbon nanotube (CNT), and conducting polymer (CP). Each component in the MnO(2)/CNT/CP film provides unique and critical function to achieve optimized electrochemical properties. The electrochemical performance of the film is evaluated by cyclic voltammetry, and constant-current charge/discharge cycling techniques. Specific capacitance (SC) of the ternary composite electrode can reach 427 F/g. Even at high mass loading and high concentration of MnO(2) (60%), the film still showed SC value as high as 200 F/g. The electrode also exhibited excellent charge/discharge rate and good cycling stability, retaining over 99% of its initial charge after 1000 cycles. The results demonstrated that MnO(2) is effectively utilized with assistance of other components (fFWNTs and poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) in the electrode. Such ternary composite is very promising for the next generation high performance electrochemical supercapacitors.

High-yield exfoliation of graphene using ternary-solvent strategy for detecting volatile organic compounds

Science.gov (United States)

Zhang, Shao-Lin; Zhang, Zhijun; Yang, Woo-Chul

2016-01-01

Despite the great progress in the theory and experimental verification we made in past decade, the practical application of graphene is still hindered by the lack of efficient, economical, scalable, ease-processing exfoliation method. Herein, we propose a facile, low-cost, and efficient liquid-phase exfoliation process using low boiling-temperature solvent mixture to fabricate few-layer graphene in large scale. The Hansen solubility parameter theory was applied to help optimize the composition of solvent mixture. Aqueous-based ternary-solvent mixture, for the first time, was adapted to exfoliate graphene. We demonstrate that the exfoliation efficiency using ternary-solvent mixture surpasses that from binary-solvent approach. The final product concentration after optimization was over 260 μg/ml. The concentrated graphene dispersion was used to fabricate gas sensor for detecting volatile organic gases. Taking advantage of large surface area, large number of adsorption sites, and well-preserved basal plane, the mass-produced graphene nanosheets exhibited promising sensing potential toward ethanol and methanol vapors.

Selection of mRNA 5'-untranslated region sequence with high translation efficiency through ribosome display

International Nuclear Information System (INIS)

Mie, Masayasu; Shimizu, Shun; Takahashi, Fumio; Kobatake, Eiry

2008-01-01

The 5'-untranslated region (5'-UTR) of mRNAs functions as a translation enhancer, promoting translation efficiency. Many in vitro translation systems exhibit a reduced efficiency in protein translation due to decreased translation initiation. The use of a 5'-UTR sequence with high translation efficiency greatly enhances protein production in these systems. In this study, we have developed an in vitro selection system that favors 5'-UTRs with high translation efficiency using a ribosome display technique. A 5'-UTR random library, comprised of 5'-UTRs tagged with a His-tag and Renilla luciferase (R-luc) fusion, were in vitro translated in rabbit reticulocytes. By limiting the translation period, only mRNAs with high translation efficiency were translated. During translation, mRNA, ribosome and translated R-luc with His-tag formed ternary complexes. They were collected with translated His-tag using Ni-particles. Extracted mRNA from ternary complex was amplified using RT-PCR and sequenced. Finally, 5'-UTR with high translation efficiency was obtained from random 5'-UTR library

Highly sensitive panchromatic ternary polymer photodetectors enabled by Förster resonance energy transfer and post solvent treatment

Science.gov (United States)

Wang, Hanyu; Zheng, Yifan; Qin, Ruiheng; Yu, Junsheng

2018-03-01

A panchromatic ternary polymer photodetector (PPD) with broadband response from 300 to 1000 nm is fabricated via incorporating poly({4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-bʹ]dithiophene-2,6-diyl}{3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl}) (PTB7) as the third component in poly(diketopyrrolopyrrole-terthiophene) (PDPP3T) [6]:-phenyl-C71-butyric acid methyl ester (PC71BM), revealing a high detectivity (D *) of 7.02  ×  1011 Jones at 850 nm. Through the analysis of photoluminescence and external quantum efficiency spectroscopy, we find that PTB7 can not only improve the absorption between 500-750 nm to induce more excitons, but also provide non-radiative transfer energy to PDPP3T via Förster resonance energy transfer (FRET). Moreover, we employ post solvent treatment (PST) to rectify the morphology of ternary blends, thus reducing charge recombination, suppressing dark current, and boosting the D * to 1.57  ×  1012 Jones at 850 nm, which is 2.34 folds higher than that of the untreated PPDs. This work indicates that the incorporation of FRET donor and PST in ternary blends is an effective way to develop highly sensitive panchromatic PPDs.

Efficient Bisphenol-A detection based on the ternary metal oxide (TMO) composite by electrochemical approaches

International Nuclear Information System (INIS)

Ahmed, Jahir; Rahman, Mohammed M.; Siddiquey, Iqbal A.; Asiri, Abdullah M.; Hasnat, Mohammad A.

2017-01-01

Highlights: •Ternary metal oxides (TMO) composites prepared by wet-chemical method. •Highly sensitive and selective Bisphenol A (BPA) sensor by I–V method. •Ultra-low detection limit was obtained by 3N/S. •Real environmental samples were analyzed. •Health care and environmental safety -- Abstract: A facile wet chemical method in basic medium was used to synthesis the ternary metal oxides (TMO; ZnO.CoO.FeO) composites at low temperature. The calcined TMO was characterized by FESEM, EDS, UV/vis., FTIR spectroscopy, EIS, and XRD systematically. Glassy carbon electrode (GCE) was modified with the TMO using 5% Nafion at room conditions. The resultant electrode was used for selective detection of Bisphenol-A (BPA) using cyclic voltammetry (CV). It was observed that the TMO electrode exhibited an excellent sensitivity (3.28 μAμM −1 cm −2 ), low detection limit (LOD: 1.2 ± 0.1 nM; S/N = 3), higher stability, very good repeatability, and reproducibility. In diagnostic exploration, a linear calibration plot was obtained for a wide range of concentration of BPA (LDR: 0.80 to 7.20 μM; r 2 : 0.99). This method represents an efficient way of sensitive sensor development for the detection of toxic and carcinogenic phenolic compounds.

Energy efficiency policy in a non-cooperative world

International Nuclear Information System (INIS)

Barla, Philippe; Proost, Stef

2012-01-01

In this paper, we explore energy efficiency policies in the presence of a global environmental problem and international cost interdependency associated with R and D activities. We develop a simple model with two regions where the cost of an appliance in one region depends upon the level of energy efficiency in that region and the level of R and D activities by the appliance industry. In our model, the cooperative outcome can be decentralized by imposing a tax on energy. However, we show that when regions do not cooperate, they have an incentive to adopt additional instruments to increase energy efficiency. The reason is that the lack of cooperation leads to under-taxation of the environmental externality which in turn creates an incentive to try to reduce emissions produced abroad. We illustrate this phenomenon with the Californian vehicle greenhouse gas standards.

Ternary fission

International Nuclear Information System (INIS)

Wagemans, C.

1991-01-01

Since its discovery in 1946, light (charged) particle accompanied fission (ternary fission) has been extensively studied, for spontaneous as well as for induced fission reactions. The reason for this interest was twofold: the ternary particles being emitted in space and time close to the scission point were expected to supply information on the scission point configuration and the ternary fission process was an important source of helium, tritium, and hydrogen production in nuclear reactors, for which data were requested by the nuclear industry. Significant experimental progress has been realized with the advent of high-resolution detectors, powerful multiparameter data acquisition systems, and intense neutron and photon beams. As far as theory is concerned, the trajectory calculations (in which scission point parameters are deduced from the experimental observations) have been very much improved. An attempt was made to explain ternary particle emission in terms of a Plateau-Rayleigh hydrodynamical instability of a relatively long cylindrical neck or cylindrical nucleus. New results have also been obtained on the so-called open-quotes trueclose quotes ternary fission (fission in three about-equal fragments). The spontaneous emission of charged particles has also clearly been demonstrated in recent years. This chapter discusses the main characteristics of ternary fission, theoretical models, light particle emission probabilities, the dependence of the emission probabilities on experimental variables, light particle energy distributions, light particle angular distributions, correlations between light particle accompanied fission observables, open-quotes trueclose quotes ternary fission, and spontaneous emission of heavy ions. 143 refs., 18 figs., 8 tabs

Ternary Organic Solar Cells with Coumarin7 as the Donor Exhibiting Greater Than 10% Power Conversion Efficiency and a High Fill Factor of 75.

Science.gov (United States)

Chen, Xin-Wei; Tao, Si-Lu; Fan, Cong; Chen, Dong-Cheng; Zhou, Ling; Lin, Hui; Zheng, Cai-Jun; Su, Shi-Jian

2017-09-06

Ternary bulk heterojunction (BHJ) is a brilliant photovoltaic technology for improving the performance of organic solar cells (OSCs), because the light absorption range can be significantly extended by using multiple donors or acceptor materials. In this paper, coumarin7 (C7), a small organic molecule typical led used in organic light-emitting diodes, was initially exploited as second electron-donor component in ternary bulk heterojunction OSCs along with conventional blend system spolythieno[3,4-b]-thiophene/benzodithiophene(PTB7) and [6,6]-phenyl-C71 -butyric acid methyl(PC 71 BM). A champion PCE value of 10.28% was realized in the ternary OSCs when incorporated with 10 wt % C7 doping ratio in the donors, corresponding to about 35% enhancement compared with the PTB7:PC 71 BM-based OSCs, a high fill factor (FF) of 75.03%, a short-circuit currentdensity (J sc ) of 18.72 mA cm -2 and an open-circuit voltage (V oc ) of 0.73 V. The enhanced performance of the ternary OSCs can be attributed to the simultaneous improvement of the FF and the J sc . In addition to extended light absorption, a perfect nanofiber filament active layer morphology is obtained due to the good compatibility between C7 and PTB7, which facilitates the balance of charge transportation and the suppression of charge recombination. This investigation suggests that coumarin derivatives, which have completely different structure with polymer donors, can also be used to fabricate ternary solar cells and have the potential applications to obtain amazing performance after further device engineering and optimization.

Blind Cooperative Routing for Scalable and Energy-Efficient Internet of Things

KAUST Repository

Bader, Ahmed; Alouini, Mohamed-Slim

2016-01-01

Multihop networking is promoted in this paper for energy-efficient and highly-scalable Internet of Things (IoT). Recognizing concerns related to the scalability of classical multihop routing and medium access techniques, the use of blind cooperation

New type ternary NiAlCe layered double hydroxide photocatalyst for efficient visible-light photoreduction of CO2 into CH4

Science.gov (United States)

Li, Ji; (Bill Yang, Y. J.

2018-02-01

New type of ternary NiAlCe layered double hydroxide photocatalyst was synthesized by a simple hydrothermal reaction. The obtained photocatalyst shows efficient visible-light activity for CO2 reduction to CH4. We have investigated the optimal Ce content in the catalyst and analyzed the mechanism by materials characterization. Additionally, a novel alkali etching method was used to construct the porous structure. The effect of the porosity and morphologies on the activity is investigated. It is found that the ternary NiAlCe layered double hydroxide photocatalyst with porosity showing the best photocatalytic activity among all the samples. Based on the characterization and first principle calculation, the detailed photocatalytic mechanism of the ternary NiAlCe layered double hydroxide photocatalyst is deduced.

Towards Efficient Wireless Body Area Network Using Two-Way Relay Cooperation.

Science.gov (United States)

Waheed, Maham; Ahmad, Rizwan; Ahmed, Waqas; Drieberg, Micheal; Alam, Muhammad Mahtab

2018-02-13

The fabrication of lightweight, ultra-thin, low power and intelligent body-borne sensors leads to novel advances in wireless body area networks (WBANs). Depending on the placement of the nodes, it is characterized as in/on body WBAN; thus, the channel is largely affected by body posture, clothing, muscle movement, body temperature and climatic conditions. The energy resources are limited and it is not feasible to replace the sensor's battery frequently. In order to keep the sensor in working condition, the channel resources should be reserved. The lifetime of the sensor is very crucial and it highly depends on transmission among sensor nodes and energy consumption. The reliability and energy efficiency in WBAN applications play a vital role. In this paper, the analytical expressions for energy efficiency (EE) and packet error rate (PER) are formulated for two-way relay cooperative communication. The results depict better reliability and efficiency compared to direct and one-way relay communication. The effective performance range of direct vs. cooperative communication is separated by a threshold distance. Based on EE calculations, an optimal packet size is observed that provides maximum efficiency over a certain link length. A smart and energy efficient system is articulated that utilizes all three communication modes, namely direct, one-way relay and two-way relay, as the direct link performs better for a certain range, but the cooperative communication gives better results for increased distance in terms of EE. The efficacy of the proposed hybrid scheme is also demonstrated over a practical quasi-static channel. Furthermore, link length extension and diversity is achieved by joint network-channel (JNC) coding the cooperative link.

Towards Efficient Wireless Body Area Network Using Two-Way Relay Cooperation

Directory of Open Access Journals (Sweden)

Maham Waheed

2018-02-01

Full Text Available The fabrication of lightweight, ultra-thin, low power and intelligent body-borne sensors leads to novel advances in wireless body area networks (WBANs. Depending on the placement of the nodes, it is characterized as in/on body WBAN; thus, the channel is largely affected by body posture, clothing, muscle movement, body temperature and climatic conditions. The energy resources are limited and it is not feasible to replace the sensor’s battery frequently. In order to keep the sensor in working condition, the channel resources should be reserved. The lifetime of the sensor is very crucial and it highly depends on transmission among sensor nodes and energy consumption. The reliability and energy efficiency in WBAN applications play a vital role. In this paper, the analytical expressions for energy efficiency (EE and packet error rate (PER are formulated for two-way relay cooperative communication. The results depict better reliability and efficiency compared to direct and one-way relay communication. The effective performance range of direct vs. cooperative communication is separated by a threshold distance. Based on EE calculations, an optimal packet size is observed that provides maximum efficiency over a certain link length. A smart and energy efficient system is articulated that utilizes all three communication modes, namely direct, one-way relay and two-way relay, as the direct link performs better for a certain range, but the cooperative communication gives better results for increased distance in terms of EE. The efficacy of the proposed hybrid scheme is also demonstrated over a practical quasi-static channel. Furthermore, link length extension and diversity is achieved by joint network-channel (JNC coding the cooperative link.

True ternary fission in 310126X

International Nuclear Information System (INIS)

Banupriya, B.; Vijayaraghavan, K.R.; Balasubramaniam, M.

2015-01-01

All possible combinations are minimized by the two dimensional minimization process and minimized with respect to neutron numbers and proton numbers of the fragments. Potential energy is low and Q - value is high at true ternary fission region. It shows that true ternary mode is the dominant mode in the ternary fission of superheavy nuclei. Also, the results show that the fragments with neutron magic numbers are the dominant one in the ternary fission of superheavy nuclei whereas the fragments with proton magic numbers are the dominant one in the ternary fission of heavy nuclei

Russia-EU energy efficiency cooperation in the Baltic region: the untapped potential

Directory of Open Access Journals (Sweden)

Romanova T. A.

2014-03-01

Full Text Available A stereotypical understanding of EU-Russia energy relations is often reduced to trade in oil and natural gas, which downplays the importance of energy efficiency cooperation. Such cooperation is promoted within the Energy Charter and its Treaty, Partnership and Cooperation Agreement, Energy Dialogue, Common Economic Space, Partnership for Modernisation. However, it lacks practical development, which relates to the instability of the legal environment in Russia, insufficient mechanisms of financial support for energy conservation projects and poor political support. Nevertheless, energy efficiency cooperation is capable of changing Russia-EU energy cooperation qualitatively: it offers a cheaper way to meet the needs of the EU, redefines interdependence between the parties, and introduces new elements of equality between them. Energy efficiency cooperation also transforms the patterns of the EU-Russia legal harmonization, creates new conditions for the convergence of regulations and the development of the middle class in Russia. Due to its specific features, cooperation in the Baltic Sea region becomes a locomotive of the Russia-EU energy efficiency cooperation, and, as a result, is capable of changing the quality of relations between the partners.

Energy-efficient cooperative protocols for full-duplex relay channels

KAUST Repository

Khafagy, Mohammad Galal

2013-12-01

In this work, energy-efficient cooperative protocols are studied for full-duplex relaying (FDR) with loopback interference. In these protocols, relay assistance is only sought under certain conditions on the different link outages to ensure effective cooperation. Recently, an energy-efficient selective decode-And-forward protocol was proposed for FDR, and was shown to outperform existing schemes in terms of outage. Here, we propose an incremental selective decode-And-forward protocol that offers additional power savings, while keeping the same outage performance. We compare the performance of the two protocols in terms of the end-to-end signal-to-noise ratio cumulative distribution function via closed-form expressions. Finally, we corroborate our theoretical results with simulation, and show the relative relay power savings in comparison to non-selective cooperation in which the relay cooperates regardless of channel conditions. © 2013 IEEE.

Energy-efficient cooperative protocols for full-duplex relay channels

KAUST Repository

Khafagy, Mohammad Galal; Ismail, Amr; Alouini, Mohamed-Slim; Aï ssa, Sonia

2013-01-01

In this work, energy-efficient cooperative protocols are studied for full-duplex relaying (FDR) with loopback interference. In these protocols, relay assistance is only sought under certain conditions on the different link outages to ensure effective cooperation. Recently, an energy-efficient selective decode-And-forward protocol was proposed for FDR, and was shown to outperform existing schemes in terms of outage. Here, we propose an incremental selective decode-And-forward protocol that offers additional power savings, while keeping the same outage performance. We compare the performance of the two protocols in terms of the end-to-end signal-to-noise ratio cumulative distribution function via closed-form expressions. Finally, we corroborate our theoretical results with simulation, and show the relative relay power savings in comparison to non-selective cooperation in which the relay cooperates regardless of channel conditions. © 2013 IEEE.

Balancing Accuracy and Computational Efficiency for Ternary Gas Hydrate Systems

Science.gov (United States)

White, M. D.

2011-12-01

phase transitions. This paper describes and demonstrates a numerical solution scheme for ternary hydrate systems that seeks a balance between accuracy and computational efficiency. This scheme uses a generalize cubic equation of state, functional forms for the hydrate equilibria and cage occupancies, variable switching scheme for phase transitions, and kinetic exchange of hydrate formers (i.e., CH4, CO2, and N2) between the mobile phases (i.e., aqueous, liquid CO2, and gas) and hydrate phase. Accuracy of the scheme will be evaluated by comparing property values and phase equilibria against experimental data. Computational efficiency of the scheme will be evaluated by comparing the base scheme against variants. The application of interest will the production of a natural gas hydrate deposit from a geologic formation, using the guest molecule exchange process; where, a mixture of CO2 and N2 are injected into the formation. During the guest-molecule exchange, CO2 and N2 will predominately replace CH4 in the large and small cages of the sI structure, respectively.

High-field superconductivity in the Nb-Ti-Zr ternary system

International Nuclear Information System (INIS)

Ralls, K.M.; Rose, R.M.; Wulff, J.

1980-01-01

Resistive critical current densities, critical fields, and normal-state electrical resistivities were obtained at 4.2 0 K for 55 alloys in the Nb-Ti-Zr ternary alloy system, excepting Ti-Zr binary compositions. The resistive critical field as a function of ternary composition has a saddle point between the Nb-Ti and Nb-Zr binaries, so that ternary alloying in this system is not expected to result in higher critical fields than the binary alloys

High-field superconductivity in the Nb-Ti-Zr ternary system

Science.gov (United States)

Ralls, K. M.; Rose, R. M.; Wulff, J.

1980-06-01

Resistive critical current densities, critical fields, and normal-state electrical resistivities were obtained at 4.2 °K for 55 alloys in the Nb-Ti-Zr ternary alloy system, excepting Ti-Zr binary compositions. The resistive critical field as a function of ternary composition has a saddle point between the Nb-Ti and Nb-Zr binaries, so that ternary alloying in this system is not expected to result in higher critical fields than the binary alloys.

Binary and ternary gas mixtures for use in glow discharge closing switches

Science.gov (United States)

Hunter, S.R.; Christophorou, L.G.

1988-04-27

Highly efficient binary and ternary gas mixtures for use in diffuse glow discharge closing switches are disclosed. The binary mixtures are combinations of helium or neon and selected perfluorides. The ternary mixtures are combinations of helium, neon, or argon, a selected perfluoride, and a small amount of gas that exhibits enhanced ionization characteristics. These mixtures are shown to be the optimum choices for use in diffuse glow discharge closing switches by virtue if the combines physio-electric properties of the mixture components. 9 figs.

High-performance thermoelectric materials based on ternary TiO2/CNT/PANI composites.

Science.gov (United States)

Erden, Fuat; Li, Hui; Wang, Xizu; Wang, FuKe; He, Chaobin

2018-04-04

In the present work, we report the fabrication of high-performance thermoelectric materials using TiO2/CNT/PANI ternary composites. We showed that a conductivity of ∼2730 S cm-1 can be achieved for the binary CNT (70%)/PANI (30%) composite, which is the highest recorded value for the reported CNT/PANI composites. We further demonstrated that the Seebeck coefficient of CNT/PANI composites could be enhanced by incorporating TiO2 nanoparticles into the binary CNT/PANI composites, which could be attributed to lower carrier density and the energy scattering of low-energy carriers at the interfaces of TiO2/a-CNT and TiO2/PANI. The resulting TiO2/a-CNT/PANI ternary system exhibits a higher Seebeck coefficient and enhanced thermoelectric power. Further optimization of the thermoelectric power was achieved by water treatment and by tuning the processing temperature. A high thermoelectric power factor of 114.5 μW mK-2 was obtained for the ternary composite of 30% TiO2/70% (a-CNT (70%)/PANI (30%)), which is the highest reported value among the reported PANI based ternary composites. The improvement of thermoelectric performance by incorporation of TiO2 suggests a promising approach to enhance power factor of organic thermoelectric materials by judicial tuning of the carrier concentration and electrical conductivity.

Prediction of high-Tc conventional superconductivity in the ternary lithium borohydride system

Science.gov (United States)

Kokail, Christian; von der Linden, Wolfgang; Boeri, Lilia

2017-12-01

We investigate the superconducting ternary lithium borohydride phase diagram at pressures of 0 and 200 GPa using methods for evolutionary crystal structure prediction and linear-response calculations for the electron-phonon coupling. Our calculations show that the ground state phase at ambient pressure, LiBH4, stays in the P n m a space group and remains a wide band-gap insulator at all pressures investigated. Other phases along the 1 :1 :x Li:B:H line are also insulating. However, a full search of the ternary phase diagram at 200 GPa revealed a metallic Li2BH6 phase, which is thermodynamically stable down to 100 GPa. This superhydride phase, crystallizing in a F m 3 ¯m space group, is characterized by sixfold hydrogen-coordinated boron atoms occupying the fcc sites of the unit cell. Due to strong hydrogen-boron bonding this phase displays a critical temperature of ˜100 K between 100 and 200 GPa. Our investigations confirm that ternary compounds used in hydrogen-storage applications should exhibit high-Tc conventional superconductivity in diamond anvil cell experiments, and suggest a viable route to optimize the superconducting behavior of high-pressure hydrides, exploiting metallic covalent bonds.

Ternary mixed metal Fe-doped NiCo2O4 nanowires as efficient electrocatalysts for oxygen evolution reaction

Science.gov (United States)

Yan, Kai-Li; Shang, Xiao; Li, Zhen; Dong, Bin; Li, Xiao; Gao, Wen-Kun; Chi, Jing-Qi; Chai, Yong-Ming; Liu, Chen-Guang

2017-09-01

Designing mixed metal oxides with unique nanostructures as efficient electrocatalysts for water electrolysis has been an attractive approach for the storage of renewable energies. The ternary mixed metal spinel oxides FexNi1-xCo2O4 (x = 0, 0.1, 0.25, 0.5, 0.75, 0.9, 1) have been synthesized by a facile hydrothermal approach and calcination treatment using nickel foam as substrate. Fe/Ni ratios have been proved to affect the nanostructures of FexNi1-xCo2O, which imply different intrinsic activity for oxygen evolution reaction (OER). SEM images show that Fe0.5Ni0.5Co2O4 has the uniform nanowires morphology with about 30 nm of the diameter and 200-300 nm of the length. The OER measurements show that Fe0.5Ni0.5Co2O4 exhibits the better electrocatalytic performances with lower overpotential of 350 mV at J = 10 mA cm-2. In addition, the smaller Tafel slope of 27 mV dec-1 than other samples with different Fe/Ni ratios for Fe0.5Ni0.5Co2O4 is obtained. The improved OER activity of Fe0.5Ni0.5Co2O4 may be attributed to the synergistic effects from ternary mixed metals especially Fe-doping and the uniform nanowires supported on NF. Therefore, synthesizing Fe-doped multi-metal oxides with novel nanostructures may be a promising strategy for excellent OER electrocatalysts and it also provides a facile way for the fabrication of high-activity ternary mixed metal oxides electrocatalysts.

Impact of ternary blends of biodiesel on diesel engine performance

Directory of Open Access Journals (Sweden)

Prem Kumar

2016-06-01

Full Text Available The Pongamia and waste cooking oils are the main non edible oils for biodiesel production in India. The aim of the present work is to evaluate the fuel properties and investigate the impact on engine performance using Pongamia and waste cooking biodiesel and their ternary blend with diesel. The investigation of the fuel properties shows that Pongamia biodiesel and waste cooking biodiesel have poor cold flow property. This will lead to starting problem in the engine operation. To overcome this problem the ternary blends of diesel, waste cooking biodiesel and Pongamia biodiesel are prepared. The cloud and pour point for ternary blend, (WCB20:PB20:D60 were found to be 7 °C and 6.5 °C which are comparable to cloud and pour point of diesel 6 °C and 5 °C, respectively. The result of the test showed that brake specific fuel consumption for Pongamia biodiesel and waste cooking biodiesel is higher than ternary blend, (WCB20:PB20:D60 due to their lower energy content. The brake thermal efficiency of ternary blend and diesel is comparable while the Pongamia and waste cooking biodiesel have low efficiency. The result of investigation showed that ternary blend can be developed as alternate fuel.

Core@shell@shell structured carbon-based magnetic ternary nanohybrids: Synthesis and their enhanced microwave absorption properties

Science.gov (United States)

Yang, Erqi; Qi, Xiaosi; Xie, Ren; Bai, Zhongchen; Jiang, Yang; Qin, Shuijie; Zhong, Wei; Du, Youwei

2018-05-01

High encapsulation efficiency of core@shell@shell structured carbon-based magnetic ternary nanohybrids have been synthesized in high yield by chemical vapor deposition of acetylene directly over octahedral-shaped Fe2O3 nanoparticles. By controlling the pyrolysis temperature, Fe3O4@Fe3C@carbon nanotubes (CNTs) and Fe@Fe3C@CNTs ternary nanohybrids could be selectively produced. The optimal RL values for the as-prepared ternary nanohybrids could reach up to ca. -46.7, -52.7 and -29.5 dB, respectively. The excellent microwave absorption properties of the obtaiend ternary nanohybrids were proved to ascribe to the quarter-wavelength matching model. Moreover, the as-prepared Fe@Fe3C@CNTs ternary nanohybrids displayed remarkably enhanced EM wave absorption capabilities compared to Fe3O4@Fe3C@CNTs due to their excellent dielectric loss abilities, good complementarities between the dielectric loss and the magnetic loss, and high attenuation constant. Generally, this strategy can be extended to explore other categories of core@shell or core@shell@shell structured carbon-based nanohybrids, which is very beneficial to accelerate the advancements of high performance MAMs.

A Novel Method for Detecting and Computing Univolatility Curves in Ternary Mixtures

DEFF Research Database (Denmark)

Shcherbakov, Nataliya; Rodriguez-Donis, Ivonne; Abildskov, Jens

2017-01-01

Residue curve maps (RCMs) and univolatility curves are crucial tools for analysis and design of distillation processes. Even in the case of ternary mixtures, the topology of these maps is highly non-trivial. We propose a novel method allowing detection and computation of univolatility curves...... of the generalized univolatility and unidistribution curves in the three dimensional composition – temperature state space lead to a simple and efficient algorithm of computation of the univolatility curves. Two peculiar ternary systems, namely diethylamine – chloroform – methanol and hexane – benzene...

Hydrothermal synthesis of graphene oxide/multiwalled carbon nanotube/Fe3O4 ternary nanocomposite for removal of Cu (II) and methylene blue

Science.gov (United States)

Long, Zhihang; Zhan, Yingqing; Li, Fei; Wan, Xinyi; He, Yi; Hou, Chunyan; Hu, Hai

2017-09-01

In this work, highly activated graphene oxide/multiwalled carbon nanotube/Fe3O4 ternary nanocomposite adsorbent was prepared from a simple hydrothermal route by using ferrous sulfate as precursor. For this purpose, the graphene oxide/multiwalled carbon nanotube architectures were formed through the π-π attractions between them, followed by attaching Fe3O4 nanoparticles onto their surface. The structure and composition of as-prepared ternary nanocomposite were characterized by XRD, FTIR, XPS, SEM, TEM, Raman, TGA, and BET. It was found that the resultant porous graphene oxide/multiwalled carbon nanotube/Fe3O4 ternary nanocomposite with large surface area could effectively prevent the π-π stacking interactions between graphene oxide nanosheets and greatly improve sorption sites on the surfaces. Thus, owing to the unique ternary nanocomposite architecture and synergistic effect among various components, as-prepared ternary nanocomposite exhibited high separation efficiency when they were used to remove the Cu (II) and methylene blue from aqueous solutions. Furthermore, the adsorption isotherms of ternary nanocomposite structures for Cu (II) and methylene blue removal fitted the Langmuir isotherm model. This work demonstrated that the graphene oxide/multiwalled carbon nanotube/Fe3O4 ternary nanocomposite was promising as an efficient adsorbent for heavy metal ions and organic dye removal from wastewater in low concentration.

Energy Efficiency Analysis of a Two Dimensional Cooperative Wireless Sensor Network with Relay Selection

Directory of Open Access Journals (Sweden)

M. Kakitani

2013-06-01

Full Text Available The energy efficiency of non-cooperative and cooperative transmissions are investigated in a two-dimensional wireless sensor network, considering a target outage probability and the same end-to-end throughput for all transmission schemes. The impact of the relay selection method in the cooperative schemes is also analyzed. We show that under non line-of-sight conditions the relay selection method has a greater impact in the energy efficiency than the availability of a return channel. By its turn, under line-of-sight conditions a return channel is more valuable to the energy efficiency of cooperative transmission than the specific relay selection method. Finally, we demonstrate that the energy efficiency advantage of the cooperative over the non-cooperative transmission increases with the distance among nodes and with the nodes density.

PM1 steganographic algorithm using ternary Hamming Code

Directory of Open Access Journals (Sweden)

Kamil Kaczyński

2015-12-01

Full Text Available PM1 algorithm is a modification of well-known LSB steganographic algorithm. It has increased resistance to selected steganalytic attacks and increased embedding efficiency. Due to its uniqueness, PM1 algorithm allows us to use of larger alphabet of symbols, making it possible to further increase steganographic capacity. In this paper, we present the modified PM1 algorithm which utilizies so-called syndrome coding and ternary Hamming code. The modified algorithm has increased embedding efficiency, which means fewer changes introduced to carrier and increased capacity.[b]Keywords[/b]: steganography, linear codes, PM1, LSB, ternary Hamming code

High Performing Ternary Solar Cells through Förster Resonance Energy Transfer between Nonfullerene Acceptors.

Science.gov (United States)

Yang, Lei; Gu, Wenxing; Hong, Ling; Mi, Yang; Liu, Feng; Liu, Ming; Yang, Yufei; Sharma, Bigyan; Liu, Xinfeng; Huang, Hui

2017-08-16

Nonradiative Förster resonance energy transfer (FRET) is an important mechanism of organic solar cells, which can improve the exciton migration over a long distance, resulting in improvement of efficiency of solar cells. However, the current observations of FRET are very limited, and the efficiencies are less than 9%. In this study, FRET effect was first observed between two nonfullerene acceptors in ternary solar cells, which improved both the absorption range and exciton harvesting, leading to the dramatic enhancement in the short circuit current and power conversion efficiency. Moreover, this strategy is proved to be a versatile platform for conjugated polymers with different bandgaps, resulting in a remarkable efficiency of 10.4%. These results demonstrated a novel method to enhance the efficiency of organic soar cells.

Ternary solution-processed organic solar cells incorporating 2D materials

Science.gov (United States)

Stylianakis, Minas M.; Konios, Dimitrios; Petridis, Constantinos; Kakavelakis, George; Stratakis, Emmanuel; Kymakis, Emmanuel

2017-12-01

Recently, the study of ternary organic solar cells (OSCs) has attracted the efforts of the scientific community, leading to significantly higher performance due to the enhanced harvesting of incoming irradiation. Here, for the first time, and in order to promote this OSC architecture, we review the progress implemented by the application of two-dimensional (2D) materials in the field of blend bulk heterojunction ternary OSCs. Power conversion efficiency (PCE) improvements of the order of 40% compared to the reference binary devices, and PCEs in excess of 8% have been reported by incorporating graphene-based or other 2D materials as a third element inside the active layer. These OSCs combine the synergetic advantages of ternary devices and the superb properties of the 2D material family. In conclusion, the incorporation of the unique properties of graphene and other 2D materials inside the active layer opens up a very promising pathway in the design and construction of high-performance, simply fabricated and low- cost photovoltaic devices.

Organic Solar Cells beyond One Pair of Donor-Acceptor: Ternary Blends and More.

Science.gov (United States)

Yang, Liqiang; Yan, Liang; You, Wei

2013-06-06

Ternary solar cells enjoy both an increased light absorption width, and an easy fabrication process associated with their simple structures. Significant progress has been made for such solar cells with demonstrated efficiencies over 7%; however, their fundamental working principles are still under investigation. This Perspective is intended to offer our insights on the three major governing mechanisms in these intriguing ternary solar cells: charge transfer, energy transfer, and parallel-linkage. Through careful analysis of exemplary cases, we summarize the advantages and limitations of these three major mechanisms and suggest future research directions. For example, incorporating additional singlet fission or upconversion materials into the energy transfer dominant ternary solar cells has the potential to break the theoretical efficiency limit in single junction organic solar cells. Clearly, a feedback loop between fundamental understanding and materials selection is in urgent need to accelerate the efficiency improvement of these ternary solar cells.

Blind Cooperative Routing for Scalable and Energy-Efficient Internet of Things

KAUST Repository

Bader, Ahmed

2016-02-26

Multihop networking is promoted in this paper for energy-efficient and highly-scalable Internet of Things (IoT). Recognizing concerns related to the scalability of classical multihop routing and medium access techniques, the use of blind cooperation in conjunction with multihop communications is advocated herewith. Blind cooperation however is actually shown to be inefficient unless power control is applied. Inefficiency in this paper is projected in terms of the transport rate normalized to energy consumption. To that end, an uncoordinated power control mechanism is proposed whereby each device in a blind cooperative cluster randomly adjusts its transmit power level. An upper bound is derived for the mean transmit power that must be observed at each device. Finally, the uncoordinated power control mechanism is demonstrated to consistently outperform the simple point-to-point routing case. © 2015 IEEE.

kW-level commercial Yb-doped aluminophosphosilicate ternary laser fiber

Science.gov (United States)

Sun, Shihao; Zhan, Huan; Li, Yuwei; Liu, Shuang; Jiang, Jiali; Peng, Kun; Wang, Yuying; Ni, Li; Wang, Xiaolong; Jiang, Lei; Yu, Juan; Liu, Gang; Lu, Pengfei; Wang, Jianjun; Jing, Feng; Lin, Aoxiang

2018-03-01

Based on a master oscillator power amplifier configuration, laser performance of commercial Nufern-20/400-8M Ybdoped aluminophosphosilicate ternary laser fiber was investigated. Pumped by 976 nm laser diodes, 982 W laser output power was obtained with a slope efficiency of 84.9%. Spectrum of output was centered at 1066.56nm with 3dB bandwidth less than 0.32 nm, and the nonlinearity suppression ratio was more than 39dB. Beam quality of Mx2 and M2y were 1.55 and 1.75 at 982 W, respectively. The laser performance indicated that Nufern-20/400-8M Yb-doped aluminophosphosilicate ternary laser fiber is highly competitive for industry fiber laser use.

Rational construction of multiple interfaces in ternary heterostructure for efficient spatial separation and transfer of photogenerated carriers in the application of photocatalytic hydrogen evolution

Science.gov (United States)

Shi, Jian-Wen; Ma, Dandan; Zou, Yajun; Fan, Zhaoyang; Shi, Jinwen; Cheng, Linhao; Ji, Xin; Niu, Chunming

2018-03-01

The design of efficient and stable photocatalyst plays a critical role in the photocatalytic hydrogen evolution from water splitting. Herein, we develop a novel ZnS/CdS/ZnO ternary heterostructure by the in-situ sulfuration of CdS/ZnO, which includes four contact interfaces: CdS-ZnS interface, ZnS-ZnO interface, CdS-ZnO interface and ZnS-CdS-ZnO ternary interface, forming three charge carrier-transfer modes (type-I, type-II and direct Z-scheme) through five carrier-transfer pathways. As a result, the separation and transfer of photoexcited electron-hole pairs are promoted significantly, resulting in a high hydrogen evolution rate of 44.70 mmol h-1 g-1, which is 2, 3.7 and 8 times higher than those of binary heterostructures, CdS/ZnO, CdS/ZnS and ZnS/ZnO, respectively, and 26.5, 280 and 298 times higher than those of single CdS, ZnO and ZnS, respectively. As a counterpart ternary heterostructure, CdS/ZnS/ZnO contains only two interfaces: CdS-ZnS interface and ZnS-ZnO interface, which form two charge carrier-transfer modes (type-I and type-II) through two carrier-transfer pathways, leading to its much lower hydrogen evolution rate (27.25 mmol h-1 g-1) than ZnS/CdS/ZnO ternary heterostructure. This work is relevant for understanding the charge-transfer pathways between multi-interfaces in multicomponent heterojunctions.

Cooperative CEO Identity and Efficient Governance: Member or Outside CEO?

NARCIS (Netherlands)

Q.X. Liang (Qiao Xin); G.W.J. Hendrikse (George)

2012-01-01

textabstractA principal-agent model is formulated to capture the efficiency of cooperatives with a member CEO and cooperatives with an employed outsider as CEO. Results of the model show that the incentive strength regarding the member CEO is stronger compared to that of the outside CEO in order to

An Open-Circuit Voltage and Power Conversion Efficiency Study of Fullerene Ternary Organic Solar Cells Based on Oligomer/Oligomer and Oligomer/Polymer.

Science.gov (United States)

Zhang, Guichuan; Zhou, Cheng; Sun, Chen; Jia, Xiaoe; Xu, Baomin; Ying, Lei; Huang, Fei; Cao, Yong

2017-07-01

Variations in the open-circuit voltage (V oc ) of ternary organic solar cells are systematically investigated. The initial study of these devices consists of two electron-donating oligomers, S2 (two units) and S7 (seven units), and the electron-accepting [6,6]-phenyl C71 butyric acid methyl ester (PC 71 BM) and reveals that the V oc is continuously tunable due to the changing energy of the charge transfer state (E ct ) of the active layers. Further investigation suggests that V oc is also continuously tunable upon change in E ct in a ternary blend system that consists of S2 and its corresponding polymer (P11):PC 71 BM. It is interesting to note that higher power conversion efficiencies can be obtained for both S2:S7:PC 71 BM and S2:P11:PC 71 BM ternary systems compared with their binary systems, which can be ascribed to an improved V oc due to the higher E ct and an improved fill factor due to the improved film morphology upon the incorporation of S2. These findings provide a new guideline for the future design of conjugated polymers for achieving higher performance of ternary organic solar cells. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

On cooperative and efficient overlay network evolution based on a group selection pattern.

Science.gov (United States)

Nakao, Akihiro; Wang, Yufeng

2010-04-01

In overlay networks, the interplay between network structure and dynamics remains largely unexplored. In this paper, we study dynamic coevolution between individual rational strategies (cooperative or defect) and the overlay network structure, that is, the interaction between peer's local rational behaviors and the emergence of the whole network structure. We propose an evolutionary game theory (EGT)-based overlay topology evolution scheme to drive a given overlay into the small-world structure (high global network efficiency and average clustering coefficient). Our contributions are the following threefold: From the viewpoint of peers' local interactions, we explicitly consider the peer's rational behavior and introduce a link-formation game to characterize the social dilemma of forming links in an overlay network. Furthermore, in the evolutionary link-formation phase, we adopt a simple economic process: Each peer keeps one link to a cooperative neighbor in its neighborhood, which can slightly speed up the convergence of cooperation and increase network efficiency; from the viewpoint of the whole network structure, our simulation results show that the EGT-based scheme can drive an arbitrary overlay network into a fully cooperative and efficient small-world structure. Moreover, we compare our scheme with a search-based economic model of network formation and illustrate that our scheme can achieve the experimental and analytical results in the latter model. In addition, we also graphically illustrate the final overlay network structure; finally, based on the group selection model and evolutionary set theory, we theoretically obtain the approximate threshold of cost and draw the conclusion that the small value of the average degree and the large number of the total peers in an overlay network facilitate the evolution of cooperation.

Non-transboundary pollution and the efficiency of international environmental co-operation

Energy Technology Data Exchange (ETDEWEB)

Kox, H.L.M.; Van der Tak, C.M. [Economics Department, Faculty of Economics and Econometrics, Vrije Universiteit, Amsterdam (Netherlands)

1995-10-01

The increased awareness of the transboundary pollution problems resulted in a number of international treaties, such as the Montreal protocol on ozone-depleting substances (1987), and the Basel Convention on hazardous waste (1989). Most authors writing on efficient environmental instruments make a sharp distinction between domestic and transboundary environmental problems. While the former should be abated by domestic environmental instruments, an efficient treatment of the latter requires international instruments. The underlying logic is that in case of non-transboundary pollution both the costs and benefits of environmental policies are strictly domestic, the trade-off between benefits and costs of abatement should also be a strictly domestic issue. In contrast, with transboundary pollution the trade-off between abatement costs and benefits becomes an international issue. In this paper we analyse four cases where international environmental co-ordination is required to achieve an efficient outcome, even though the environmental externality is non-transboundary in nature. Section two sketches the standard view on efficient intervention levels with regard to transborder and non-transborder pollution. In the third section we deal with cases where environmental policy is used in a trade-strategic way. The section pays attention to the motives for using domestic environmental policy as a disguise for trade policies. It will be argued that the resulting allocative efficiency can be improved upon by international co-operation. Sections 4-6 analyse three cases where international co-operation may improve the international outcome on the basis of non-coordinated domestic allocation decisions. These cases refer in particular to the situation of developing countries, when there is a high export dependency on the polluting good in combination with the existence of discrete technologies, set-up costs of environment-friendly technologies, and the existence of increasing

Non-transboundary pollution and the efficiency of international environmental co-operation

International Nuclear Information System (INIS)

Kox, H.L.M.; Van der Tak, C.M.

1995-10-01

The increased awareness of the transboundary pollution problems resulted in a number of international treaties, such as the Montreal protocol on ozone-depleting substances (1987), and the Basel Convention on hazardous waste (1989). Most authors writing on efficient environmental instruments make a sharp distinction between domestic and transboundary environmental problems. While the former should be abated by domestic environmental instruments, an efficient treatment of the latter requires international instruments. The underlying logic is that in case of non-transboundary pollution both the costs and benefits of environmental policies are strictly domestic, the trade-off between benefits and costs of abatement should also be a strictly domestic issue. In contrast, with transboundary pollution the trade-off between abatement costs and benefits becomes an international issue. In this paper we analyse four cases where international environmental co-ordination is required to achieve an efficient outcome, even though the environmental externality is non-transboundary in nature. Section two sketches the standard view on efficient intervention levels with regard to transborder and non-transborder pollution. In the third section we deal with cases where environmental policy is used in a trade-strategic way. The section pays attention to the motives for using domestic environmental policy as a disguise for trade policies. It will be argued that the resulting allocative efficiency can be improved upon by international co-operation. Sections 4-6 analyse three cases where international co-operation may improve the international outcome on the basis of non-coordinated domestic allocation decisions. These cases refer in particular to the situation of developing countries, when there is a high export dependency on the polluting good in combination with the existence of discrete technologies, set-up costs of environment-friendly technologies, and the existence of increasing

Cooperative catalysis designing efficient catalysts for synthesis

CERN Document Server

Peters, René

2015-01-01

Written by experts in the field, this is a much-needed overview of the rapidly emerging field of cooperative catalysis. The authors focus on the design and development of novel high-performance catalysts for applications in organic synthesis (particularly asymmetric synthesis), covering a broad range of topics, from the latest progress in Lewis acid / Br?nsted base catalysis to e.g. metal-assisted organocatalysis, cooperative metal/enzyme catalysis, and cooperative catalysis in polymerization reactions and on solid surfaces. The chapters are classified according to the type of cooperating acti

Ternary Weighted Function and Beurling Ternary Banach Algebra l1ω(S

Directory of Open Access Journals (Sweden)

Mehdi Dehghanian

2011-01-01

Full Text Available Let S be a ternary semigroup. In this paper, we introduce our notation and prove some elementary properties of a ternary weight function ω on S. Also, we make ternary weighted algebra l1ω(S and show that l1ω(S is a ternary Banach algebra.

Evaluation of hyaluronic acid-combined ternary complexes for serum-resistant and targeted gene delivery system.

Science.gov (United States)

Hong, Woong-Gil; Jeong, Gyeong-Won; Nah, Jae-Woon

2018-04-19

Branched polyethylenimine (bPEI) was well known as high transfection agent, which has many amine group. However, utilization of bPEI was limited due to high toxicity. To solve these problems, bPEI was introduced to low molecular weight water-soluble chitosan (LMWSC) with coupling agent. In addition, hyaluronic acid (HA), one of natural anion polymer, was introduced to binary complex of pDNA/bPEI-grafted LMWSC (LMPEI) to target the specific cancer cell and impart the serum resistant. Ternary complexes of pDNA/LMPEI/HA were prepared by electrostatic charge interaction and their binding affinity and DNase protection assay were conducted by gel retardation assay. Particle size of ternary complexes showed that had each 482 ± 245.4 (pDNA/LMPEI2%/HA, 1:16:1, w/w/w) and 410 ± 78.5 nm (pDNA/LMPEI4%/HA, 1:16:2, w/w/w). Moreover, to demonstrate serum-resistant effect of ternary complexes, particle size of them was measured according to incubated time (0-10 h) under serum condition. Transfection assay of ternary complexes showed that their transfection efficiency in CD44-receptor overexpressed HCT116 cell was higher than CD44-receptor negative CT26 cell. Additionally, intracellular uptake of ternary complexes with propidium iodide (PI)-labeled pDNA was observed to confirm targeting effect and cellular internalization by fluorescence microscopy. These results suggest that ternary complexes are superb gene carrier with excellent serum-resistant and high gene transfection. Copyright © 2017. Published by Elsevier B.V.

Effect of Ni-Co Ternary Molten Salt Catalysts on Coal Catalytic Pyrolysis Process

Science.gov (United States)

Cui, Xin; Qi, Cong; Li, Liang; Li, Yimin; Li, Song

2017-08-01

In order to facilitate efficient and clean utilization of coal, a series of Ni-Co ternary molten salt crystals are explored and the catalytic pyrolysis mechanism of Datong coal is investigated. The reaction mechanisms of coal are achieved by thermal gravimetric analyzer (TGA), and a reactive kinetic model is constructed. The microcosmic structure and macerals are observed by scanning electron microscope (SEM). The catalytic effects of ternary molten salt crystals at different stages of pyrolysis are analyzed. The experimental results show that Ni-Co ternary molten salt catalysts have the capability to bring down activation energy required by pyrolytic reactions at its initial phase. Also, the catalysts exert a preferable catalytic action on macromolecular structure decomposition and free radical polycondensation reactions. Furthermore, the high-temperature condensation polymerization is driven to decompose further with a faster reaction rate by the additions of Ni-Co ternary molten salt crystal catalysts. According to pyrolysis kinetic research, the addition of catalysts can effectively decrease the activation energy needed in each phase of pyrolysis reaction.

The influence of high shear mixing on ternary dry powder inhaler formulations.

Science.gov (United States)

Hertel, Mats; Schwarz, Eugen; Kobler, Mirjam; Hauptstein, Sabine; Steckel, Hartwig; Scherließ, Regina

2017-12-20

The blending process is a key step in the production of dry powder inhaler formulations, but only little is known about the influence of process parameters. This is especially true for high shear blending of ternary formulations. For this reason, this study aims to investigate the influence of high shear mixing process parameters (mixing time and rotation speed) on the fine particle fraction (FPF) of ternary mixtures when using budesonide as model drug, two different carrier materials and two different mixing orders. Prolonged mixing time and higher rotation speeds led to lower FPFs, possibly due to higher press-on forces acting on the active pharmaceutical ingredients (API). In addition, a clear correlation between the energy consumption of the blender (the energy input into the blend) and the reduction of the FPF could be shown. Furthermore blending the carrier and the fines before adding the API was also found to be favorable. Copyright © 2017 Elsevier B.V. All rights reserved.

Freight transportation efficiency through horizontal cooperation in Flanders

NARCIS (Netherlands)

Cruijssen, F.C.A.M.; Dullaert, W.; Joro, T.

2010-01-01

This paper describes a practical application of data envelopment analysis (DEA) to the Flemish road transportation sector. The efficiency of 82 road transportation companies responding to a large-scale survey focused on horizontal cooperation is evaluated, based on two inputs and two outputs.

Insight Into the Role of PC71BM on Enhancing the Photovoltaic Performance of Ternary Organic Solar Cells.

Science.gov (United States)

Wang, Bei; Fu, Yingying; Yan, Chi; Zhang, Rui; Yang, Qingqing; Han, Yanchun; Xie, Zhiyuan

2018-01-01

The development of non-fullerene acceptor molecules have remarkably boosted power conversion efficiency (PCE) of polymer solar cells (PSCs) due to the improved spectral coverage and reduced energy loss. An introduction of fullerene molecules into the non-fullerene acceptor-based blend may further improve the photovoltaic performance of the resultant ternary PSCs. However, the underlying mechanism is still debatable. Herein, the ternary PSCs based on PBDB-T:ITIC:PC 71 BM blend were fabricated and its PCE was increased to 10.2% compared to 9.2% for the binary PBDB-T:ITIC devices and 8.1% for the PBDB-T:PC 71 BM PSCs. Systematic investigation was carried out to disclose the effect of PC 71 BM on the blend morphology and charge transport behavior. It is found that the PC 71 BM tends to intermix with the PBDB-T donor compared to the ITIC counterpart. A small amount of PC 71 BM in the ternary blend is helpful for ITIC to aggregate and form efficient electron-transport pathways. Accordingly, the electron mobility is increased and the density of electron traps is decreased in the ternary blend in comparison with the PBDB-T:ITIC blend. Finally, the suppressed bimolecular recombination and enhanced charge collection lead to high PCE for the ternary solar cells.

Ternary-fragmentation-driving potential energies of 252Cf

Science.gov (United States)

Karthikraj, C.; Ren, Zhongzhou

2017-12-01

Within the framework of a simple macroscopic model, the ternary-fragmentation-driving potential energies of 252Cf are studied. In this work, all possible ternary-fragment combinations of 252Cf are generated by the use of atomic mass evaluation-2016 (AME2016) data and these combinations are minimized by using a two-dimensional minimization approach. This minimization process can be done in two ways: (i) with respect to proton numbers (Z1, Z2, Z3) and (ii) with respect to neutron numbers (N1, N2, N3) of the ternary fragments. In this paper, the driving potential energies for the ternary breakup of 252Cf are presented for both the spherical and deformed as well as the proton-minimized and neutron-minimized ternary fragments. From the proton-minimized spherical ternary fragments, we have obtained different possible ternary configurations with a minimum driving potential, in particular, the experimental expectation of Sn + Ni + Ca ternary fragmentation. However, the neutron-minimized ternary fragments exhibit a driving potential minimum in the true-ternary-fission (TTF) region as well. Further, the Q -value energy systematics of the neutron-minimized ternary fragments show larger values for the TTF fragments. From this, we have concluded that the TTF region fragments with the least driving potential and high Q values have a strong possibility in the ternary fragmentation of 252Cf. Further, the role of ground-state deformations (β2, β3, β4, and β6) in the ternary breakup of 252Cf is also studied. The deformed ternary fragmentation, which involves Z3=12 -19 fragments, possesses the driving potential minimum due to the larger oblate deformations. We also found that the ground-state deformations, particularly β2, strongly influence the driving potential energies and play a major role in determining the most probable fragment combinations in the ternary breakup of 252Cf.

Tuning of "antenna effect" of Eu(III) in ternary systems in aqueous medium through binding with protein.

Science.gov (United States)

Ghorai, Shyamal Kr; Samanta, Swarna Kamal; Mukherjee, Manini; Saha Sardar, Pinki; Ghosh, Sanjib

2013-02-04

A simple ternary system containing a protein [human serum albumin (HSA)/bovine serum albumin (BSA)], tetracycline hydrochloride (TC), and Eu(III) in suitable aqueous buffer medium at physiological pH (= 7.2) has been shown to exhibit highly efficient "antenna effect" compared to the binary complex of TC with Eu(III) (Eu(3)TC). The ternary system containing E. coli alkaline phosphatase (AP), TC, and Eu(III), however, shows a slight enhancement of Eu(III) emission, although the binding constant of AP with TC is 2 orders of magnitude greater than with BSA/HSA. The enhanced emission of bound TC in the binary systems containing proteins and TC gets quenched in the ternary systems containing HSA/BSA, showing the efficient energy transfer (ET) from TC to Eu(III). Steady state and time-resolved emission studies of each component in all the ternary systems in H(2)O and in D(2)O medium reveal that Eu(III) is very well protected from the O-H oscillator in the ternary system containing HSA/BSA compared to that containing AP. The docking studies locating the binding site of TC in the proteins suggest that TC binds near the surface of AP. In the case of HSA/BSA, TC resides in the interior of the protein resulting in a large shielding effect of Eu(III). The rotational correlation time (θ(c)) determined from the anisotropy decay of bound TC in the complexes and the accessible surface area (ASA) of the ligand in the complexes obtained from the docking studies also support the contention that Eu(3)TC is more exposed to solvent in the case of the ternary system consisting of AP, TC, and Eu(III). The calculated radiative lifetime and the sensitization efficiency ratio of Eu(III) in all the systems clearly demonstrate the protein mediated tuning of "antenna effect" in Eu(III).

Robust Nash Dynamic Game Strategy for User Cooperation Energy Efficiency in Wireless Cellular Networks

Directory of Open Access Journals (Sweden)

Shuhuan Wen

2012-01-01

Full Text Available Recently, there is an emerging trend of addressing “energy efficiency” aspect of wireless communications. It has been shown that cooperating users relay each other's information to improve data rates. The energy is limited in the wireless cellular network, but the mobile users refuse to relay. This paper presents an approach that encourages user cooperation in order to improve the energy efficiency. The game theory is an efficient method to solve such conflicts. We present a cellular framework in which two mobile users, who desire to communicate with a common base station, may cooperate via decode-and-forward relaying. In the case of imperfect information assumption, cooperative Nash dynamic game is used between the two users' cooperation to tackle the decision making problems: whether to cooperate and how to cooperate in wireless networks. The scheme based on “cooperative game theory” can achieve general pareto-optimal performance for cooperative games, and thus, maximize the entire system payoff while maintaining fairness.

Variation in Behavioral Reactivity Is Associated with Cooperative Restraint Training Efficiency

OpenAIRE

Bliss-Moreau, Eliza; Moadab, Gilda

2016-01-01

Training techniques that prepare laboratory animals to participate in testing via cooperation are useful tools that have the potential to benefit animal wellbeing. Understanding how animals systematically vary in their cooperative training trajectories will help trainers to design effective and efficient training programs. In the present report we document an updated method for training rhesus monkeys to cooperatively participate in restraint in a ‘primate chair.’ We trained 14 adult male mac...

Ternary Au/ZnO/rGO nanocomposites electrodes for high performance electrochemical storage devices

Science.gov (United States)

Chaudhary, Manchal; Doong, Ruey-an; Kumar, Nagesh; Tseng, Tseung Yuen

2017-10-01

The combination of metal and metal oxide nanoparticles with reduced graphene oxides (rGO) is an active electrode material for electrochemical storage devices. Herein, we have, for the first time, reported the fabrication of ternary Au/ZnO/rGO nanocomposites by using a rapid and environmentally friendly microwave-assisted hydrothermal method for high performance supercapacitor applications. The ZnO/rGO provides excellent electrical conductivity and good macro/mesopore structures, which can facilitate the rapid electrons and ions transport. The Au nanoparticles with particle sizes of 7-12 nm are homogeneously distributed onto the ZnO/rGO surface to enhance the electrochemical performance by retaining the capacitance at high current density. The Au/ZnO/rGO nanocomposites, prepared with the optimized rGO amount of 100 mg exhibit a high specific capacitance of 875 and 424 F g-1 at current densities of 1 and 20 A g-1, respectively, in 2 M KOH. In addition, the energy and power densities of ternary Au/ZnO/rGO can be up to 17.6-36.5 Wh kg-1 and 0.27-5.42 kW kg-1, respectively. Results obtained in this study clearly demonstrate the excellence of ternary Au/ZnO/rGO nanocomposites as the active electrode materials for electrochemical pseudocapacitor performance and can open an avenue to fabricate metal/metal oxide/rGO nanocomposites for electrochemical storage devices with both high energy and power densities.

Highly Efficient Cooperative Catalysis by Co ^III (Porphyrin) Pairs in Interpenetrating Metal-Organic Frameworks

Energy Technology Data Exchange (ETDEWEB)

Lin, Zekai; Zhang, Zhi-Ming; Chen, Yu-Sheng; Lin, Wenbin (UC); (Xiamen)

2016-12-02

A series of porous twofold interpenetrated In-Co^III(porphyrin) metal–organic frameworks (MOFs) were constructed by in situ metalation of porphyrin bridging ligands and used as efficient cooperative catalysts for the hydration of terminal alkynes. The twofold interpenetrating structure brings adjacent Co^III(porphyrins) in the two networks parallel to each other with a distance of about 8.8 Å, an ideal distance for the simultaneous activation of both substrates in alkyne hydration reactions. As a result, the In-Co^III(porphyrin) MOFs exhibit much higher (up to 38 times) catalytic activity than either homogeneous catalysts or MOF controls with isolated Co^III(porphyrin) centers, thus highlighting the potential application of MOFs in cooperative catalysis.

Atomistic study of ternary oxides as high-temperature solid lubricants

Science.gov (United States)

Gao, Hongyu

Friction and wear are important tribological phenomena tightly associated with the performance of tribological components/systems such as bearings and cutting machines. In the process of contact and sliding, friction and wear lead to energy loss, and high friction and wear typically result in shortened service lifetime. To reduce friction and wear, solid lubricants are generally used under conditions where traditional liquid lubricants cannot be applied. However, it is challenging to maintain the functionality of those materials when the working environment becomes severe. For instance, at elevated temperatures (i.e., above 400 °C), most traditional solid lubricants, such as MoS2 and graphite, will easily oxidize or lose lubricity due to irreversible chemical changes. For such conditions, it is necessary to identify materials that can remain thermally stable as well as lubricious over a wide range of temperatures. Among the currently available high-temperature solid lubricants, Ag-based ternary metal oxides have recently drawn attention due to their low friction and ability to resist oxidation. A recent experimental study showed that the Ag-Ta-O ternary exhibited an extremely low coefficient of friction (0.06) at 750 °C. To fully uncover the lubricious nature of this material as a high-temperature solid lubricant, a series of tribological investigations were carried out based on one promising candidate - silver tantalate (AgTaO3). The study was then extended to alternative materials, Cu-Ta-O ternaries, to accommodate a variety of application requirements. We aimed to understand, at an atomic level, the effects of physical and chemical properties on the thermal, mechanical and tribological behavior of these materials at high temperatures. Furthermore, we investigated potassium chloride films on a clean iron surface as a representative boundary lubricating system in a nonextreme environment. This investigation complemented the study of Ag/Cu-Ta-O and enhanced the

Ternary CoS{sub 2}/MoS{sub 2}/RGO electrocatalyst with CoMoS phase for efficient hydrogen evolution

Energy Technology Data Exchange (ETDEWEB)

Liu, Yan-Ru; Shang, Xiao [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); Gao, Wen-Kun [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); College of Science, China University of Petroleum (East China), Qingdao 266580 (China); Dong, Bin, E-mail: dongbin@upc.edu.cn [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); College of Science, China University of Petroleum (East China), Qingdao 266580 (China); Chi, Jing-Qi; Li, Xiao; Yan, Kai-Li; Chai, Yong-Ming [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); Liu, Yun-Qi, E-mail: liuyq@upc.edu.cn [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); Liu, Chen-Guang [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China)

2017-08-01

Highlights: • Ternary CoS{sub 2}/MoS{sub 2}/RGO with CoMoS phase as electrocatalyst for HER was prepared. • CoMoS phase have the metallic nature and highly intrinsic activity for HER. • RGO support ensures good distribution of CoMoS phase and enhances the conductivity. • The introduction of CoMoS and RGO may be a novel strategy for efficient HER of MoS{sub 2}. - Abstract: CoMoS phase with metallic character plays crucial role on enhancing the activity of MoS{sub 2} electrocatalysts for hydrogen evolution reaction (HER). However, only Co atoms located in the edges of MoS{sub 2} can create CoMoS phase, so it is a challenge to obtain CoMoS phase with homogeneous distribution limited by the layered MoS{sub 2} and doping method of Co. Herein, we reported a simple one-pot hydrothermal method to prepare novel ternary CoS{sub 2}/MoS{sub 2}/RGO with CoMoS phase for HER using reduced graphene oxide (RGO) as support. XPS proves the formation of CoMoS phase, implying the enhanced activity for HER. RGO support ensures the well distribution of CoMoS phase and enhances the conductivity of CoS{sub 2}/MoS{sub 2}/RGO. Compared to CoS{sub 2}/RGO, MoS{sub 2}/RGO and CoS{sub 2}/MoS{sub 2}, the obtained CoS{sub 2}/MoS{sub 2}/RGO shows superior activity for HER with an onset overpotential of −80 mV (vs. RHE), small Tafel slope of 56 mV dec{sup −1}, high exchange current density of 11.4 μA cm{sup −2} and rigid electrochemical durability. The enhanced performances for HER may be ascribed to the formation of CoMoS phase with high activity and the existence of RGO support with good electrical conductivitys in ternary CoS{sub 2}/MoS{sub 2}/RGO. Therefore, the introduction of CoMoS phase and RGO into MoS{sub 2} could effectively enhance electrocatalytic properties for HER.

All-optical symmetric ternary logic gate

Science.gov (United States)

Chattopadhyay, Tanay

2010-09-01

Symmetric ternary number (radix=3) has three logical states (1¯, 0, 1). It is very much useful in carry free arithmetical operation. Beside this, the logical operation using this type of number system is also effective in high speed computation and communication in multi-valued logic. In this literature all-optical circuits for three basic symmetrical ternary logical operations (inversion, MIN and MAX) are proposed and described. Numerical simulation verifies the theoretical model. In this present scheme the different ternary logical states are represented by different polarized state of light. Terahertz optical asymmetric demultiplexer (TOAD) based interferometric switch has been used categorically in this manuscript.

An Energy Efficient Cooperative Hierarchical MIMO Clustering Scheme for Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Sungyoung Lee

2011-12-01

Full Text Available In this work, we present an energy efficient hierarchical cooperative clustering scheme for wireless sensor networks. Communication cost is a crucial factor in depleting the energy of sensor nodes. In the proposed scheme, nodes cooperate to form clusters at each level of network hierarchy ensuring maximal coverage and minimal energy expenditure with relatively uniform distribution of load within the network. Performance is enhanced by cooperative multiple-input multiple-output (MIMO communication ensuring energy efficiency for WSN deployments over large geographical areas. We test our scheme using TOSSIM and compare the proposed scheme with cooperative multiple-input multiple-output (CMIMO clustering scheme and traditional multihop Single-Input-Single-Output (SISO routing approach. Performance is evaluated on the basis of number of clusters, number of hops, energy consumption and network lifetime. Experimental results show significant energy conservation and increase in network lifetime as compared to existing schemes.

An Energy-Efficient Scheme for Multirelay Cooperative Networks with Energy Harvesting

Directory of Open Access Journals (Sweden)

Dingcheng Yang

2016-01-01

Full Text Available This study investigates an energy-efficient scheme in multirelay cooperative networks with energy harvesting where multiple sessions need to communicate with each other via the relay node. A two-step optimal method is proposed which maximizes the system energy efficiency, while taking into account the receiver circuit energy consumption. Firstly, the optimal power allocation for relay nodes is determined to maximize the system throughput; this is based on directional water-filling algorithm. Secondly, using quantum particle swarm optimization (QPSO, a joint relay node selection and session grouping optimization is proposed. With this algorithm, sessions can be classified into multiple groups that are assisted by the specific relay node with the maximum energy efficiency. This approach leads to a better global optimization in searching ability and efficiency. Simulation results show that the proposed scheme can improve the energy efficiency effectively compared with direct transmission and opportunistic relay-selected cooperative transmission.

Prediction of superconducting ternary hydride MgGeH6: from divergent high-pressure formation routes.

Science.gov (United States)

Ma, Yanbin; Duan, Defang; Shao, Ziji; Li, Da; Wang, Liyuan; Yu, Hongyu; Tian, Fubo; Xie, Hui; Liu, Bingbing; Cui, Tian

2017-10-18

Invigorated by the high temperature superconductivity in some binary hydrogen-dominated compounds, we systematically explored high-pressure phase diagrams and superconductivity of a ternary Mg-Ge-H system using ab initio methods. Stoichiometric MgGeH 6 with high hydrogen content exhibiting Pm3[combining macron] symmetry was predicted from a series of high-pressure synthesis paths. We performed an in-depth study on three distinct formation routes to MgGeH 6 , i.e., Mg + Ge + 3H 2 → MgGeH 6 , MgGe + 3H 2 → MgGeH 6 and MgH 2 + GeH 4 → MgGeH 6 at high pressures. By directly squeezing three elemental solids Mg + Ge + 3H 2 , we obtained ternary MgGeH 6 at 200 GPa. By adding a little bit of the MgGe alloy into hydrogen, we found that MgGeH 6 can form and stabilize at about 200 GPa. More intriguingly, upon compressing MgH 2 and GeH 4 to 250 GPa, we also predicted the same MgGeH 6 . Electron structure calculations reveal that the cubic MgGeH 6 is a good metal and takes on ionic character. Electron-phonon coupling calculation reveals a large λ = 1.16 for MgGeH 6 at 200 GPa. In particular, we found that ternary MgGeH 6 could be a potential high temperature superconductor with a superconducting transition temperature T c of ∼67 K at 200 GPa.

Automated Cooperative Trajectories for a More Efficient and Responsive Air Transportation System

Science.gov (United States)

Hanson, Curt

2015-01-01

The NASA Automated Cooperative Trajectories project is developing a prototype avionics system that enables multi-vehicle cooperative control by integrating 1090 MHz ES ADS-B digital communications with onboard autopilot systems. This cooperative control capability will enable meta-aircraft operations for enhanced airspace utilization, as well as improved vehicle efficiency through wake surfing. This briefing describes the objectives and approach to a flight evaluation of this system planned for 2016.

Enhancing Performance of Large-Area Organic Solar Cells with Thick Film via Ternary Strategy.

Science.gov (United States)

Zhang, Jianqi; Zhao, Yifan; Fang, Jin; Yuan, Liu; Xia, Benzheng; Wang, Guodong; Wang, Zaiyu; Zhang, Yajie; Ma, Wei; Yan, Wei; Su, Wenming; Wei, Zhixiang

2017-06-01

Large-scale fabrication of organic solar cells requires an active layer with high thickness tolerability and the use of environment-friendly solvents. Thick films with high-performance can be achieved via a ternary strategy studied herein. The ternary system consists of one polymer donor, one small molecule donor, and one fullerene acceptor. The small molecule enhances the crystallinity and face-on orientation of the active layer, leading to improved thickness tolerability compared with that of a polymer-fullerene binary system. An active layer with 270 nm thickness exhibits an average power conversion efficiency (PCE) of 10.78%, while the PCE is less than 8% with such thick film for binary system. Furthermore, large-area devices are successfully fabricated using polyethylene terephthalate (PET)/Silver gride or indium tin oxide (ITO)-based transparent flexible substrates. The product shows a high PCE of 8.28% with an area of 1.25 cm 2 for a single cell and 5.18% for a 20 cm 2 module. This study demonstrates that ternary organic solar cells exhibit great potential for large-scale fabrication and future applications. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ternary fission

Indian Academy of Sciences (India)

the energy minimization of all possible ternary breakups of a heavy radioactive nucleus. Further, within the TCM we have analysed the competition between different geometries as well as different positioning of the fragments. Also, an attempt was made to calculate the mass distribution of ternary fission process within the ...

Gossip Versus Punishment: The Efficiency of Reputation to Promote and Maintain Cooperation

Science.gov (United States)

Wu, Junhui; Balliet, Daniel; Van Lange, Paul A. M.

2016-01-01

Prior theory suggests that reputation spreading (e.g., gossip) and punishment are two key mechanisms to promote cooperation in groups, but no behavioral research has yet examined their relative effectiveness and efficiency in promoting and maintaining cooperation. To examine these issues, we observed participants interacting in a four-round public goods game (PGG) with or without gossip and punishment options, and a subsequent two-round trust game (TG). We manipulated gossip as the option to send notes about other group members to these members’ future partners, and punishment as the option to assign deduction points to reduce other group members’ outcomes with a fee-to-fine ratio of 1:3. Findings revealed that in the four-round PGG, the option to gossip increased both cooperation and individual earnings, whereas the option to punish had no overall effect on cooperation (but a positive effect on cooperation in the last two rounds of the PGG) and significantly decreased individual earnings. Importantly, the initial option to gossip made people more trusting and trustworthy in the subsequent TG when gossip was no longer possible, compared to the no-gossip condition. Thus, we provide some initial evidence that gossip may be more effective and efficient than punishment to promote and maintain cooperation. PMID:27039896

Gossip Versus Punishment: The Efficiency of Reputation to Promote and Maintain Cooperation.

Science.gov (United States)

Wu, Junhui; Balliet, Daniel; Van Lange, Paul A M

2016-04-04

Prior theory suggests that reputation spreading (e.g., gossip) and punishment are two key mechanisms to promote cooperation in groups, but no behavioral research has yet examined their relative effectiveness and efficiency in promoting and maintaining cooperation. To examine these issues, we observed participants interacting in a four-round public goods game (PGG) with or without gossip and punishment options, and a subsequent two-round trust game (TG). We manipulated gossip as the option to send notes about other group members to these members' future partners, and punishment as the option to assign deduction points to reduce other group members' outcomes with a fee-to-fine ratio of 1:3. Findings revealed that in the four-round PGG, the option to gossip increased both cooperation and individual earnings, whereas the option to punish had no overall effect on cooperation (but a positive effect on cooperation in the last two rounds of the PGG) and significantly decreased individual earnings. Importantly, the initial option to gossip made people more trusting and trustworthy in the subsequent TG when gossip was no longer possible, compared to the no-gossip condition. Thus, we provide some initial evidence that gossip may be more effective and efficient than punishment to promote and maintain cooperation.

Towards Reliable and Energy-Efficient Incremental Cooperative Communication for Wireless Body Area Networks.

Science.gov (United States)

Yousaf, Sidrah; Javaid, Nadeem; Qasim, Umar; Alrajeh, Nabil; Khan, Zahoor Ali; Ahmed, Mansoor

2016-02-24

In this study, we analyse incremental cooperative communication for wireless body area networks (WBANs) with different numbers of relays. Energy efficiency (EE) and the packet error rate (PER) are investigated for different schemes. We propose a new cooperative communication scheme with three-stage relaying and compare it to existing schemes. Our proposed scheme provides reliable communication with less PER at the cost of surplus energy consumption. Analytical expressions for the EE of the proposed three-stage cooperative communication scheme are also derived, taking into account the effect of PER. Later on, the proposed three-stage incremental cooperation is implemented in a network layer protocol; enhanced incremental cooperative critical data transmission in emergencies for static WBANs (EInCo-CEStat). Extensive simulations are conducted to validate the proposed scheme. Results of incremental relay-based cooperative communication protocols are compared to two existing cooperative routing protocols: cooperative critical data transmission in emergencies for static WBANs (Co-CEStat) and InCo-CEStat. It is observed from the simulation results that incremental relay-based cooperation is more energy efficient than the existing conventional cooperation protocol, Co-CEStat. The results also reveal that EInCo-CEStat proves to be more reliable with less PER and higher throughput than both of the counterpart protocols. However, InCo-CEStat has less throughput with a greater stability period and network lifetime. Due to the availability of more redundant links, EInCo-CEStat achieves a reduced packet drop rate at the cost of increased energy consumption.

Ternary particle yields in 249Cf(nth,f)

Science.gov (United States)

Tsekhanovich, I.; Büyükmumcu, Z.; Davi, M.; Denschlag, H. O.; Gönnenwein, F.; Boulyga, S. F.

2003-03-01

An experiment measuring ternary particle yields in 249Cf(nth,f) was carried out at the high flux reactor of the Institut Laue-Langevin using the Lohengrin recoil mass separator. Parameters of energy distributions were determined for 27 ternary particles up to 30Mg and their yields were calculated. The yields of 17 further ternary particles were estimated on the basis of the systematics developed. The heaviest particles observed in the experiment are 37Si and 37S; their possible origin is discussed.

Fiscal 1998 research report. Study on the possibility of international cooperation for high- efficiency urban heat use systems for CO{sub 2} reduction; 1998 nendo chosa hokokusho. CO{sub 2} sakugen no tame no toshi netsu riyo system kokoritsuka ni kakawaru kokusai kyoryoku kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This research aims at study on the possibility of international cooperation such as technology transfer and technical cooperation between developed countries for introduction of high-efficiency urban heat use systems into developing countries from the viewpoint of global warming control. On the case of a city in the south-eastern district in China, this research studies the principle of international cooperation such as technology transfer and research cooperation through survey on social and economical restrictions to their introduction into developing countries and study on a CO{sub 2} reduction effect by the introduction. This report describes the current technology for high-efficiency urban heat use systems in developed countries, the current energy use in Chinese cities and some issues, current heat use technologies, the case study on the potential and constraint of high- efficiency urban heat use systems, and the case study on the CO{sub 2} reduction effect of the high-efficiency urban heat use system. Expectation for Japanese technical cooperation as such international cooperation is described. (NEDO)

Ternary systems

International Nuclear Information System (INIS)

Kagan, D.N.; Hubberstey, P.; Barker, M.G.

1985-01-01

The paper reviews the experimental and theoretical studies carried out on multicomponent alkali metal systems. Solid-liquid phase equilibria studies are mainly concerned with the systems Na-K-Rb and Na-K-Cs, and data on the liquidus temperatures in these systems are presented. The thermodynamic properties of the ternary Na-K-Cs eutectic system have been determined experimentally, and the enthalpy, heat capacity and excess functions of the alloy are given. An analysis of calculational methods used in determining thermodynamic functions of ternary liquid metals systems is described. Finally, data are tabulated for the density, compressibility, saturated vapour pressure, viscosity and thermal conductivity of the ternary Na-K-Cs eutectic system. (UK)

Structural characterization and bioavailability of ternary nanoparticles consisting of amylose, α-linoleic acid and β-lactoglobulin complexed with naringin.

Science.gov (United States)

Feng, Tao; Wang, Ke; Liu, Fangfang; Ye, Ran; Zhu, Xiao; Zhuang, Haining; Xu, Zhimin

2017-06-01

Naringin is a bioflavonoid that is rich in citrus plants and possesses enormous health benefits. However, the use of naringin as a nutraceutical is significantly limited by its low bioavailability. In this study, a novel water-soluble ternary nanoparticle material consisting of amylose, α-linoleic acid and β-lactoglobulin was developed to encapsulate naringin to improve its bioavailability. The physicochemical characteristics of the ternary nanoparticle-naringin inclusion complex were analysed by ultraviolet-visible spectroscopy (UV), Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), high-resolution transmission electron microscopy (TEM), X-ray diffractometry (XRD) and particle size distribution. The results confirmed the formation of the ternary nanoparticle-naringin inclusion complex. The encapsulation efficiency (EE) and loading content (LC) of the ternary nanoparticle-naringin inclusion complex were 78.73±4.17% and 14.51±3.43%, respectively. In addition, the results of the ternary nanoparticle-naringin inclusion complex in simulated gastric fluid (SGF) and simulated intestinal fluid (SIF) demonstrated that naringin can be gradually released from the complex. In conclusion, ternary nanoparticles are considered promising carriers to effectively improve the bioavailability of naringin. Copyright © 2017 Elsevier B.V. All rights reserved.

Ternary superconductor ''NbTiTa'' for high field superfluid magnets

International Nuclear Information System (INIS)

McInturff, A.D.; Carson, J.; Larbalestier, D.; Lee, P.; McKinnel, J.; Kanithi, H.; McDonald, W.; O'Larey, P.

1990-06-01

The possibility exists to obtain a higher 'Hc 2 ' upper critical field in the NbTi system which is normally limited by a spin-orbit coupling term. The introduction of scattering reduces this coupling. The spin-orbit scattering rate is proportional to Z 4 and therefore leads logically to the introduction of a high atomic number element which is more or less similar with respect to all of the other properties, i.e., Tc. Previous studies have shown Tantalum to be an excellent choice. The present work represents an attempt to obtain a high current density, high field ternary magnet conductor (Jc (10T, 2K, ρeff = 10 -12 Ω-cm)) > 2000A/mm 2 . This goal was met, but the conductor was clearly not optimized

Ternary particle yields in 249Cf(nth,f)

International Nuclear Information System (INIS)

Tsekhanovich, I.; Bueyuekmumcu, Z.; Davi, M.; Denschlag, H.O.; Goennenwein, F.; Boulyga, S.F.

2003-01-01

An experiment measuring ternary particle yields in 249 Cf(n th ,f) was carried out at the high flux reactor of the Institut Laue-Langevin using the Lohengrin recoil mass separator. Parameters of energy distributions were determined for 27 ternary particles up to 30 Mg and their yields were calculated. The yields of 17 further ternary particles were estimated on the basis of the systematics developed. The heaviest particles observed in the experiment are 37 Si and 37 S; their possible origin is discussed

Efficiency of international cooperation schemata in African countries: A comparative analysis using a data envelopment analysis approach

Directory of Open Access Journals (Sweden)

Victor Martin-Perez

2017-02-01

Full Text Available Background: Efficiency measurement by means of data envelopment analysis (DEA in the non-profit sector has focused on the so-called Stage I of non-profit organisations, namely, fundraising efforts (which are the most influential determinants of raising funds in order to increase the amount of contributions. However, for the so-called Stage II of non-profit organisations, namely, spending the achieved resources to program services delivery, DEA studies are very scarce. In attempting to address this research gap and to the best of our knowledge, this investigation is the first study that applies DEA to the assessment of international cooperation schemata. Consequently, we offer a significant contribution to the literature by overcoming the limitations of other techniques used to assess the efficiency and providing new insight into the efficiency of targeted different international cooperation schemata (ICS in international cooperation development projects. Aim: The purpose of this study is to evaluate and compare the efficiency of the ICS of developmental projects funded by the Spanish Agency for International Cooperation for Development. Setting: Our setting is composed of different international cooperation projects funded with different schemata by the Spanish Agency for International Cooperation for Development between 2002 and 2006 in two African countries that are top priority targets of Spanish international aid: Morocco, and Mozambique. Methods: Using a sample of 48 international cooperation projects carried out in two African countries considered priorities in the Spanish Cooperation Master Plan, we analyse project efficiency using DEA. Results: The findings suggest that some schemata are more efficient than others when applied to international cooperation projects (ICS. Specifically, we find that permanent open-call subsidies are more efficient than non-governmental development organisation subsidies. Conclusion: Measures for evaluating

Development and application of high strength ternary boride base cermets

International Nuclear Information System (INIS)

Takagi, Ken-ichi

2006-01-01

Reaction boronizing sintering is a novel strategy to form a ternary boride coexisting with a metal matrix in a cermet during liquid phase sintering. This new sintering technique has successfully developed world first ternary boride base cermets with excellent mechanical properties such as Mo 2 FeB 2 , Mo 2 NiB 2 and WCoB base ones. In these cermets Mo 2 FeB 2 and Mo 2 NiB 2 base ones consist of a tetragonal M 3 B 2 (M: metal)-type complex boride as a hard phase and a transition metal base matrix. The cermets have already been applied to wear resistant applications such as injection molding machine parts, can making tools, and hot copper extruding dies, etc. This paper focuses on the characteristics, effects of the additional elements on the mechanical properties and structure, and practical applications of the ternary boride base cermets. - Graphical abstract: TRS and hardness of Ni-5B-51Mo-17.5Cr and Ni-5B-51Mo-12.5Cr-5V-xMn mass% cermets as functions of Mn content (Fig. 17)

Energy Efficient Four Level Cooperative Opportunistic Communication for Wireless Personal Area Networks (WPAN)

DEFF Research Database (Denmark)

Rohokale, Vandana M.; Inamdar, Sandeep; Prasad, Neeli R.

2013-01-01

For wireless sensor networks (WSN),energy is a scarce resource. Due to limited battery resources, the energy consumption is the critical issue for the transmission as well as reception of the signals in the wireless communication. WSNs are infrastructure-less shared network demanding more energy...... consumption due to collaborative transmissions. This paper proposes a new cooperative opportunistic four level model for IEEE 802.15.4 Wireless Personal Area Network (WPAN).The average per node energy consumption is observed merely about 0.17mJ for the cooperative wireless communication which proves...... the proposed mechanism to be energy efficient. This paper further proposes four levels of cooperative data transmission from source to destination to improve network coverage with energy efficiency....

Ternary chalcopyrite semiconductors

CERN Document Server

Shay, J L; Pamplin, B R

2013-01-01

Ternary Chalcopyrite Semiconductors: Growth, Electronic Properties, and Applications covers the developments of work in the I-III-VI2 and II-IV-V2 ternary chalcopyrite compounds. This book is composed of eight chapters that focus on the crystal growth, characterization, and applications of these compounds to optical communications systems. After briefly dealing with the status of ternary chalcopyrite compounds, this book goes on describing the crystal growth of II-IV-V2 and I-III-VI2 single crystals. Chapters 3 and 4 examine the energy band structure of these semiconductor compounds, illustrat

Ternary nitrogen-doped graphene/nickel ferrite/polyaniline nanocomposites for high-performance supercapacitors

Science.gov (United States)

Wang, Wenjuan; Hao, Qingli; Lei, Wu; Xia, Xifeng; Wang, Xin

2014-12-01

The electrochemical property of graphene can be significantly enhanced due to the incorporating of heteroatoms into graphene. In this article, the ternary nitrogen-doped graphene/nickel ferrite/polyaniline (NGNP) nanocomposite is synthesized by a facile two-step approach and its electrochemical properties as electrodes for supercapacitors are studied by various electrochemical measurements. The specific capacitance of NGNP is 645.0 F g-1 at 1 mV s-1 and 667.0 F g-1 at 0.1 A g-1 in a three- and two-electrode system, respectively, much higher than other binary electrodes. In a two-electrode symmetric system, the energy density of the NGNP electrode is 92.7 W h kg-1 at a power density of 110.8 W kg-1, moreover, that of the supercapacitor based on NGNP can also reach 23.2 W h kg-1 at a power density of 27.7 W kg-1. In addition, the capacitance loses only 5% after repeating test for 5000 cycles, and about 10% after 10,000 cycles at a high current density 5 A g-1. The results demonstrate the novel ternary NGNP electrode produced by the current economical method will gain promising applications in supercapacitors and other devices by virtue of its outstanding characteristics (high specific capacitance, high power and energy density, excellent cycle life).

English Cooperative Learning Mode in a Rural Junior High School in China

Science.gov (United States)

Zhang, Haiyan; Peng, Wen; Sun, Liuhua

2017-01-01

Cooperative learning is one of the most recognized and fruitful research areas in modern education practice. It has been widely used in many countries as an effective teaching strategy to improve class efficiency and students' comprehensive language ability since the 1990's. This paper takes JA Junior High School, a rural junior high school in…

Ternary mixtures of alkyltriphenylphosphonium bromides (C12 TPB ...

Indian Academy of Sciences (India)

Administrator

Critical Micellar Concentrations (CMCs) by conductometry, but their ternary mixtures produce single ... efficiently quenched pyrene fluorescence; the performances of the homologues in this respect were assessed. Keywords ..... The shape of the amphiphile aggregates ..... Haque M E, Das A R and Moulik S P 1999 J. Colloid.

MnO2 Nanorods Intercalating Graphene Oxide/Polyaniline Ternary Composites for Robust High-Performance Supercapacitors

Science.gov (United States)

Han, Guangqiang; Liu, Yun; Zhang, Lingling; Kan, Erjun; Zhang, Shaopeng; Tang, Jian; Tang, Weihua

2014-04-01

New ternary composites of MnO2 nanorods, polyaniline (PANI) and graphene oxide (GO) have been prepared by a two-step process. The 100 nm-long MnO2 nanorods with a diameter ~20 nm are conformably coated with PANI layers and fastened between GO layers. The MnO2 nanorods incorporated ternary composites electrode exhibits significantly increased specific capacitance than PANI/GO binary composite in supercapacitors. The ternary composite with 70% MnO2 exhibits a highest specific capacitance reaching 512 F/g and outstanding cycling performance, with ~97% capacitance retained over 5000 cycles. The ternary composite approach offers an effective solution to enhance the device performance of metal-oxide based supercapacitors for long cycling applications.

Memristor-based ternary content addressable memory (mTCAM) for data-intensive computing

International Nuclear Information System (INIS)

Zheng, Le; Shin, Sangho; Steve Kang, Sung-Mo

2014-01-01

A memristor-based ternary content addressable memory (mTCAM) is presented. Each mTCAM cell, consisting of five transistors and two memristors to store and search for ternary data, is capable of remarkable nonvolatility and higher storage density than conventional CMOS-based TCAMs. Each memristor in the cell can be programmed individually such that high impedance is always present between searchlines to reduce static energy consumption. A unique two-step write scheme offers reliable and energy-efficient write operations. The search voltage is designed to ensure optimum sensing margins with the presence of variations in memristor devices. Simulations of the proposed mTCAM demonstrate functionalities in write and search modes, as well as a search delay of 2 ns and a search of 0.99 fJ/bit/search for a word width of 128 bits. (paper)

Carbon nanotube-supported Au-Pd alloy with cooperative effect of metal nanoparticles and organic ketone/quinone groups as a highly efficient catalyst for aerobic oxidation of amines.

Science.gov (United States)

Deng, Weiping; Chen, Jiashu; Kang, Jincan; Zhang, Qinghong; Wang, Ye

2016-05-21

Functionalised carbon nanotube (CNT)-supported Au-Pd alloy nanoparticles were highly efficient catalysts for the aerobic oxidation of amines. We achieved the highest turnover frequencies (>1000 h(-1)) for the oxidative homocoupling of benzylamine and the oxidative dehydrogenation of dibenzylamine. We discovered a cooperative effect between Au-Pd nanoparticles and ketone/quinone groups on CNTs.

Binary and ternary systems

International Nuclear Information System (INIS)

Petrov, D.A.

1986-01-01

Conditions for thermodynamical equilibrium in binary and ternary systems are considered. Main types of binary and ternary system phase diagrams are sequently constructed on the basis of general regularities on the character of transition from one equilibria to others. New statements on equilibrium line direction in the diagram triple points and their isothermal cross sections are developed. New represenations on equilibria in case of monovariant curve minimum and maximum on three-phase equilibrium formation in ternary system are introduced

Construction of g-C3N4/CeO2/ZnO ternary photocatalysts with enhanced photocatalytic performance

Science.gov (United States)

Yuan, Yuan; Huang, Gui-Fang; Hu, Wang-Yu; Xiong, Dan-Ni; Zhou, Bing-Xin; Chang, Shengli; Huang, Wei-Qing

2017-07-01

Promoting the spatial separation of photoexcited charge carriers is of paramount significance for photocatalysis. In this work, binary g-C3N4/CeO2 nanosheets are first prepared by pyrolysis and subsequent exfoliation method, then decorated with ZnO nanoparticles to construct g-C3N4/CeO2/ZnO ternary nanocomposites with multi-heterointerfaces. Notably, the type-II staggered band alignments existing between any two of the constituents, as well as the efficient three-level transfer of electron-holes in unique g-C3N4/CeO2/ZnO ternary composites, leads to the robust separation of photoexcited charge carriers, as verified by its photocurrent increased by 8 times under visible light irradiation. The resulting g-C3N4/CeO2/ZnO ternary nanocomposites unveil appreciably increased photocatalytic activity, faster than that of pure g-C3N4, ZnO and g-C3N4/CeO2 by a factor of 11, 4.6 and 3.7, respectively, and good stability toward methylene blue (MB) degradation. The remarkably enhanced photocatalytic activity of g-C3N4/CeO2/ZnO ternary heterostructures can be interpreted in terms of lots of active sites of nanosheet shapes and the efficient charge separation owing to the resulting type-II band alignment with more than one heterointerface and the efficient three-level electron-hole transfer. A plausible mechanism is also elucidated via active species trapping experiments with various scavengers, which indicating that the photogenerated holes and •OH radicals play a crucial role in photodegradation reaction under visible light irradiation. This work suggest that the rational design and construction of type II multi-heterostructures is powerful for developing highly efficient and reusable visible-light photocatalysts for environmental purification and energy conversion.

Highly Efficient Interception and Precipitation of Uranium(VI) from Aqueous Solution by Iron-Electrocoagulation Combined with Cooperative Chelation by Organic Ligands.

Science.gov (United States)

Li, Peng; Zhun, Bao; Wang, Xuegang; Liao, PingPing; Wang, Guanghui; Wang, Lizhang; Guo, Yadan; Zhang, Weimin

2017-12-19

A new strategy combining iron-electrocoagulation and organic ligands (OGLs) cooperative chelation was proposed to screen and precipitate low concentrations (0-18.52 μmol/L) of uranium contaminant in aqueous solution. We hypothesized that OGLs with amino, hydroxyl, and carboxyl groups hydrophobically/hydrophilically would realize precuring of uranyl ion at pH electrocoagulation would achieve faster and more efficient uranium precipitation. Experimentally, the strategy demonstrated highly efficient uranium(VI) precipitation efficiency, especially with hydrophilic macromolecular OGLs. The uranium removal efficiency at optimized experimental condition reached 99.65%. The decrease of zeta potential and the lattice enwrapping between U-OGLs chelates and flocculation precursor were ascribed to the enhanced uranium precipitation activity. Uranium was precipitated as oxides of U(VI) or higher valences that were easily captured in aggregated micelles under low operation current potential. The actual uranium tailing wastewater was treated, and a satisfied uranium removal efficiency of 99.02% was discovered. After elution of the precipitated flocs, a concentrated uranium solution (up to 106.52 μmol/L) with very few other metallic impurities was obtained. Therefore, the proposed strategy could remove uranium and concentrate it concurrently. This work could provide new insights into the purification and recovery of uranium from aqueous solutions in a cost-effective and environmentally friendly process.

Facilitated charge transport in ternary interconnected electrodes for flexible supercapacitors with excellent power characteristics

Science.gov (United States)

Chen, Wanjun; He, Yongmin; Li, Xiaodong; Zhou, Jinyuan; Zhang, Zhenxing; Zhao, Changhui; Gong, Chengshi; Li, Shuankui; Pan, Xiaojun; Xie, Erqing

2013-11-01

Flexible and high performance supercapacitors are very critical in modern society. In order to develop the flexible supercapacitors with high power density, free-standing and flexible three-dimensional graphene/carbon nanotubes/MnO2 (3DG/CNTs/MnO2) composite electrodes with interconnected ternary 3D structures were fabricated, and the fast electron and ion transport channels were effectively constructed in the rationally designed electrodes. Consequently, the obtained 3DG/CNTs/MnO2 composite electrodes exhibit superior specific capacitance and rate capability compared to 3DG/MnO2 electrodes. Furthermore, the 3DG/CNTs/MnO2 based asymmetric supercapacitor demonstrates the maximum energy and power densities of 33.71 W h kg-1 and up to 22 727.3 W kg-1, respectively. Moreover, the asymmetric supercapacitor exhibits excellent cycling stability with 95.3% of the specific capacitance maintained after 1000 cycle tests. Our proposed synthesis strategy to construct the novel ternary 3D structured electrodes can be efficiently applied to other high performance energy storage/conversion systems.Flexible and high performance supercapacitors are very critical in modern society. In order to develop the flexible supercapacitors with high power density, free-standing and flexible three-dimensional graphene/carbon nanotubes/MnO2 (3DG/CNTs/MnO2) composite electrodes with interconnected ternary 3D structures were fabricated, and the fast electron and ion transport channels were effectively constructed in the rationally designed electrodes. Consequently, the obtained 3DG/CNTs/MnO2 composite electrodes exhibit superior specific capacitance and rate capability compared to 3DG/MnO2 electrodes. Furthermore, the 3DG/CNTs/MnO2 based asymmetric supercapacitor demonstrates the maximum energy and power densities of 33.71 W h kg-1 and up to 22 727.3 W kg-1, respectively. Moreover, the asymmetric supercapacitor exhibits excellent cycling stability with 95.3% of the specific capacitance maintained

Synthesis and loading-dependent characteristics of nitrogen-doped graphene foam/carbon nanotube/manganese oxide ternary composite electrodes for high performance supercapacitors.

Science.gov (United States)

Cheng, Tao; Yu, Baozhi; Cao, Linli; Tan, Huiyun; Li, Xinghua; Zheng, Xinliang; Li, Weilong; Ren, Zhaoyu; Bai, Jinbo

2017-09-01

The ternary composite electrodes, nitrogen-doped graphene foam/carbon nanotube/manganese dioxide (NGF/CNT/MnO 2 ), have been successfully fabricated via chemical vapor deposition (CVD) and facile hydrothermal method. The morphologies of the MnO 2 nanoflakes presented the loading-dependent characteristics and the nanoflake thickness could also be tuned by MnO 2 mass loading in the fabrication process. The correlation between their morphology and electrochemical performance was systematically investigated by controlling MnO 2 mass loading in the ternary composite electrodes. The electrochemical properties of the flexible ternary electrode (MnO 2 mass loading of 70%) exhibited a high areal capacitance of 3.03F/cm 2 and a high specific capacitance of 284F/g at the scan rate of 2mV/s. Moreover, it was interesting to find that the capacitance of the NGF/CNT/MnO 2 composite electrodes showed a 51.6% increase after 15,000 cycles. The gradual increase in specific capacitance was due to the formation of defective regions in the MnO 2 nanostructures during the electrochemical cycles of the electrodes, which further resulted in increased porosity, surface area, and consequently increased electrochemical capacity. This work demonstrates a rarely reported conclusion about loading-dependent characteristics for the NGF/CNT/MnO 2 ternary composite electrodes. It will bring new perspectives on designing novel ternary or multi-structure for various energy storage applications. Copyright © 2017 Elsevier Inc. All rights reserved.

Design and synthesis of ternary cobalt ferrite/graphene/polyaniline hierarchical nanocomposites for high-performance supercapacitors

Science.gov (United States)

Xiong, Pan; Huang, Huajie; Wang, Xin

2014-01-01

A ternary cobalt ferrite/graphene/polyaniline nanocomposite (CGP) is designed and fabricated via a facile two-step approach: cobalt ferrite nanoparticles dispersed on graphene sheets are achieved by a hydrothermal method, followed by coating with polyaniline (PANI) through in situ polymerization process. Electrochemical measurements demonstrate that the specific capacitance of the resulting ternary hybrid (CGP) is up to 1133.3 F g-1 at a scan rate of 1 mV s-1 and 767.7 F g-1 at a current density of 0.1 A g-1 using a three-electrode system, while 716.4 F g-1 at a scan rate of 1 mV s-1 and 392.3 F g-1 at a current density of 0.1 A g-1 using a two-electrode system, which are significantly higher than those of pure CoFe2O4, graphene and PANI, or binary CoFe2O4/graphene, CoFe2O4/PANI and graphene/PANI hybrids. In addition, over 96% of the initial capacitance can be retained after repeating test for 5000 cycles, demonstrating a high cycling stability. The extraordinary electrochemical performance of the ternary CGP nanocomposite can be attributed to its well-designed nanostructure and the synergistic effects of the individual components.

Solvent engineering for high-quality perovskite solar cell with an efficiency approaching 20%

Science.gov (United States)

Wu, Tongyue; Wu, Jihuai; Tu, Yongguang; He, Xin; Lan, Zhang; Huang, Miaoliang; Lin, Jianming

2017-10-01

The perovskite layer is the most crucial factor for the high performance perovskite solar cells. Based on solvent engineering, we develop a ternary-mixed-solvent method for the growth of high-quality [Cs0.05(MA0.17FA0.83)0.95Pb(I0.83Br0.17)3] cation-anion-mixed perovskite films by introducing N-methyl-2-pyrrolidone (NMP) into the precursor mixed solution. By controlling rapid nucleation and retarding crystal growth via intermediate phase PbI2-NMP (Lewis acid-base adduct), a dense, large grain, pinhole-free and long charge carrier lifetime perovskite film is obtained. By optimizing the precursor solvent composition, the perovskite solar cell achieves an impressive power conversion efficiency of 19.61% under one-sun illumination. The research presented here provides a facile, low-cost and highly efficient way for the preparation of perovskite solar cells.

Ternary polyplex micelles with PEG shells and intermediate barrier to complexed DNA cores for efficient systemic gene delivery.

Science.gov (United States)

Li, Junjie; Chen, Qixian; Zha, Zengshi; Li, Hui; Toh, Kazuko; Dirisala, Anjaneyulu; Matsumoto, Yu; Osada, Kensuke; Kataoka, Kazunori; Ge, Zhishen

2015-07-10

Simultaneous achievement of prolonged retention in blood circulation and efficient gene transfection activity in target tissues has always been a major challenge hindering in vivo applications of nonviral gene vectors via systemic administration. Herein, we constructed novel rod-shaped ternary polyplex micelles (TPMs) via complexation between the mixed block copolymers of poly(ethylene glycol)-b-poly{N'-[N-(2-aminoethyl)-2-aminoethyl]aspartamide} (PEG-b-PAsp(DET)) and poly(N-isopropylacrylamide)-b-PAsp(DET) (PNIPAM-b-PAsp(DET)) and plasmid DNA (pDNA) at room temperature, exhibiting distinct temperature-responsive formation of a hydrophobic intermediate layer between PEG shells and pDNA cores through facile temperature increase from room temperature to body temperature (~37 °C). As compared with binary polyplex micelles of PEG-b-PAsp(DET) (BPMs), TPMs were confirmed to condense pDNA into a more compact structure, which achieved enhanced tolerability to nuclease digestion and strong counter polyanion exchange. In vitro gene transfection results demonstrated TPMs exhibiting enhanced gene transfection efficiency due to efficient cellular uptake and endosomal escape. Moreover, in vivo performance evaluation after intravenous injection confirmed that TPMs achieved significantly prolonged blood circulation, high tumor accumulation, and promoted gene expression in tumor tissue. Moreover, TPMs loading therapeutic pDNA encoding an anti-angiogenic protein remarkably suppressed tumor growth following intravenous injection into H22 tumor-bearing mice. These results suggest TPMs with PEG shells and facilely engineered intermediate barrier to inner complexed pDNA have great potentials as systemic nonviral gene vectors for cancer gene therapy. Copyright © 2015 Elsevier B.V. All rights reserved.

DNA supercoiling enhances cooperativity and efficiency of an epigenetic switch

DEFF Research Database (Denmark)

Norregaard, Kamilla; Andersson, Magnus; Sneppen, Kim

2013-01-01

Bacteriophage λ stably maintains its dormant prophage state but efficiently enters lytic development in response to DNA damage. The mediator of these processes is the λ repressor protein, CI, and its interactions with λ operator DNA. This λ switch is a model on the basis of which epigenetic switch...... with relaxed DNA, the presence of supercoils greatly enhances juxtaposition probability. Also, the efficiency and cooperativity of the λ switch is significantly increased in the supercoiled system compared with a linear assay, increasing the Hill coefficient....

Description of the ternary system Cu-Ge-Te

International Nuclear Information System (INIS)

Dogguy, M.; Carcaly, C.; Rivet, J.; Flahaut, J.

1977-01-01

The Cu-Ge-Te ternary system has been studied by DTA and by crystallographic and metallographic analysis. The existence of a ternary compound Cu 2 GeTe 3 is demonstrated; this compound has a ternary incongruent melting point at 500 0 C. This ternary compound has a superstructure of a zinc blende type. The study shows the existence of five ternary eutectics. Two liquid-liquid miscibility gaps exist: the first is situated entirely in the ternary system; the second gives a monotectic region within the ternary system. (Auth.)

Comparing the Productive Efficiency of Cooperatives and Private Enterprises: The Portuguese Wine Industry as a Case Study

OpenAIRE

Barros, Carlos Pestana; Santos, J.C. Gomes

2007-01-01

This paper compares the efficiency of cooperatives and private enterprises in the Portuguese wine industry, employing data envelopment analysis (DEA). The use of DEA for the analysis of comparative efficiency within a sector is a key tool in evaluating organizational competitiveness. Competitiveness should be based on benchmarking the different types of organizations that comprise the viniculture sector. We conclude that Portuguese wine cooperatives, on average, are more efficient than their ...

Realizing Ternary Logic in FPGAs for SWL DSP Systems

Directory of Open Access Journals (Sweden)

Tayeb Din

2013-07-01

Full Text Available Recently SWL (Short Word Length DSP (Digital Signal Processing applications has been proposed to overcome multiplier complexity that is evident in most of the digital applications. These SWL applications have been processed through sigma-delta modulation as a key element. For such applications, adder design plays vital role and can impact upon the chip area and its performance. In this paper, a ternary approach for adder tree has been proposed instead of binary that can accommodate more data with less chip-area at the cost of extra pin. The proposed ternary adder tree has been designed and developed in Quartus-II using three different design strategies namely T-gate (Ternary gate, LUT (Look Up Table and algebraic equations. Through rigorous simulation it was found that T-gate technique results in superior performance, an average of 23.5 and 33% improvement compared to the same adder structure based on Boolean Algebraic Equation and LUT, respectively. The proposed adder design would benefit the efficient implementation of SWL applications.

Highly active sulfided CoMo catalysts supported on (ZrO{sub 2}–TiO{sub 2})/Al{sub 2}O{sub 3} ternary oxides

Energy Technology Data Exchange (ETDEWEB)

Escobar, José, E-mail: jeaguila@imp.mx [Instituto Mexicano del Petróleo, Eje Central Lázaro Cárdenas 152, Col. San Bartolo Atepehuacan, Gustavo A. Madero, México, D.F. 07730 (Mexico); De Los Reyes, José A., E-mail: jarh@xanum.uam.mx [Area de Ing. Química, UAM – Iztapalapa, San Rafael Atlixco 186, Col. Vicentina, Iztapalapa, México, D.F. 09340 (Mexico); Ulín, Carlos A. [Area de Ing. Química, UAM – Iztapalapa, San Rafael Atlixco 186, Col. Vicentina, Iztapalapa, México, D.F. 09340 (Mexico); Barrera, María C., E-mail: mcbdgavilan@gmail.com [Facultad de Ciencias Químicas, Universidad Veracruzana, Av. Universidad km. 7.5, Col. Santa Isabel, Coatzacoalcos, Veracruz, México, D.F. 96538 (Mexico)

2013-12-16

} ternary carrier resulted, after sulfiding, in increased amount of MoS{sub 2} phase that could be efficiently promoted by cobalt. - Highlights: • High HDS activity of sulfided CoMo catalysts supported on (ZrO{sub 2}–TiO{sub 2})/Al{sub 2}O{sub 3}. • Enhanced activity in HDS of dibenzothiophene and 4,6-dimethyl-dibenzothiophene. • Low proportion of tetrahedral Mo{sup 6+} over impregnated precursor with ternary carrier. • Ternary support combines texture of Al{sub 2}O{sub 3} with ZrO{sub 2}–TiO{sub 2} surface properties.

Effective, Efficient Online Training in Cooperative Extension

Directory of Open Access Journals (Sweden)

Jane Chin Young

2014-09-01

Full Text Available In order to keep pace with media and communications trends in education, Cooperative Extension (CE faces the need to shift from traditional face-to-face delivery to online alternatives. This exploratory study focused on evaluating the effectiveness of on-demand, interactive online training compared to its face-to-face counterpart. Targeted for CE staff and volunteers whose work impacts youth, families and communities, the design centered on the university’s cost-effective in-house technology tools. The study results make the case for online delivery as effective and efficient. Strategies for developing a process for online delivery in CE are also offered.

Facilitated charge transport in ternary interconnected electrodes for flexible supercapacitors with excellent power characteristics.

Science.gov (United States)

Chen, Wanjun; He, Yongmin; Li, Xiaodong; Zhou, Jinyuan; Zhang, Zhenxing; Zhao, Changhui; Gong, Chengshi; Li, Shuankui; Pan, Xiaojun; Xie, Erqing

2013-12-07

Flexible and high performance supercapacitors are very critical in modern society. In order to develop the flexible supercapacitors with high power density, free-standing and flexible three-dimensional graphene/carbon nanotubes/MnO2 (3DG/CNTs/MnO2) composite electrodes with interconnected ternary 3D structures were fabricated, and the fast electron and ion transport channels were effectively constructed in the rationally designed electrodes. Consequently, the obtained 3DG/CNTs/MnO2 composite electrodes exhibit superior specific capacitance and rate capability compared to 3DG/MnO2 electrodes. Furthermore, the 3DG/CNTs/MnO2 based asymmetric supercapacitor demonstrates the maximum energy and power densities of 33.71 W h kg(-1) and up to 22,727.3 W kg(-1), respectively. Moreover, the asymmetric supercapacitor exhibits excellent cycling stability with 95.3% of the specific capacitance maintained after 1000 cycle tests. Our proposed synthesis strategy to construct the novel ternary 3D structured electrodes can be efficiently applied to other high performance energy storage/conversion systems.

A novel method based on selective laser sintering for preparing high-performance carbon fibres/polyamide12/epoxy ternary composites

Science.gov (United States)

Zhu, Wei; Yan, Chunze; Shi, Yunsong; Wen, Shifeng; Liu, Jie; Wei, Qingsong; Shi, Yusheng

2016-09-01

A novel method based on selective laser sintering (SLS) process is proposed for the first time to prepare complex and high-performance carbon fibres/polyamide12/epoxy (CF/PA12/EP) ternary composites. The procedures are briefly described as follows: prepare polyamide12 (PA12) coated carbon fibre (CF) composite powder; build porous green parts by SLS; infiltrate the green parts with high-performance thermosetting epoxy (EP) resin; and finally cure the resin at high temperature. The obtained composites are a ternary composite system consisting of the matrix of novolac EP resin, the reinforcement of CFs and the transition thin layer of PA12 with a thickness of 595 nm. The SEM images and micro-CT analysis prove that the ternary system is a three-dimensional co-continuous structure and the reinforcement of CFs are well dispersed in the matrix of EP with the volume fraction of 31%. Mechanical tests show that the composites fabricated by this method yield an ultimate tensile strength of 101.03 MPa and a flexural strength of 153.43 MPa, which are higher than those of most of the previously reported SLS materials. Therefore, the process proposed in this paper shows great potential for manufacturing complex, lightweight and high-performance CF reinforced composite components in aerospace, automotive industries and other areas.

Thermal decomposition of cesium-ethylene-ternary graphite intercalation compounds

International Nuclear Information System (INIS)

Matsumoto, R.; Oishi, Y.; Arii, T.

2010-01-01

In this paper, the thermal decomposition of air-stable Cs-ethylene-ternary graphite intercalation compounds (GICs) is discussed. The air stability of Cs-GICs is improved remarkably after the absorption of ethylene into their interlayer nanospace, because the ethylene molecules oligomerize and block the movement of Cs atoms. In addition, the evaporation of Cs atoms from the Cs-ethylene-ternary GICs is observed above 400 o C under a N 2 atmosphere of 100 Pa by ion attachment mass spectrometry. Although the results indicate that Cs-ethylene-ternary GICs remain stable up to approximately 400 o C, their thermal stability is not very high as compared to that of Cs-GICs.

New ternary hydride formation in U-Ti-H system

International Nuclear Information System (INIS)

Yamamoto, Takuya; Kayano, Hideo; Yamawaki, Michio.

1991-01-01

Hydrogen absorption properties of two titanium-rich uranium alloys, UTi 2 and UTi 4 , were studied in order to prepare and identify the recently found ternary hydride. They slowly reacted with hydrogen of the initial pressure of 10 5 Pa at 873K to form the ternary hydride. The hydrogenated specimen mainly consisted of the pursued ternary hydride but contained also U(or UO 2 ), TiH x , and some transient phases. X-ray powder diffraction and Electron Probe Micro Analysis proved that it was the UTi 2 H x with the expected MgCu 2 structure, though all the X-ray peaks were broad probably because of inhomogeneity. This compound had extremely high resistance to powdering on its formation, which showed high potential utilities for a non-powdering tritium storage system or for other purposes. (author)

On ternary species mixing and combustion in isotropic turbulence at high pressure

Science.gov (United States)

Lou, Hong; Miller, Richard S.

2004-05-01

Effects of Soret and Dufour cross-diffusion, whereby both concentration and thermal diffusion occur in the presence of mass fraction, temperature, and pressure gradients, are investigated in the context of both binary and ternary species mixing and combustion in isotropic turbulence at large pressure. The compressible flow formulation is based on a cubic real-gas state equation, and includes generalized forms for heat and mass diffusion derived from nonequilibrium thermodynamics and fluctuation theory. A previously derived formulation of the generalized binary species heat and mass fluxes is first extended to the case of ternary species, and appropriate treatment of the thermal and mass diffusion factors is described. Direct numerical simulations (DNS) are then conducted for both binary and ternary species mixing and combustion in stationary isotropic turbulence. Mean flow temperatures and pressures of =700 K and =45 atm are considered to ensure that all species mixtures remain in the supercritical state such that phase changes do not occur. DNS of ternary species systems undergoing both pure mixing and a simple chemical reaction of the form O2+N2→2NO are then conducted. It is shown that stationary scalar states previously observed for binary mixing persist for the ternary species problem as well; however, the production and magnitude of the scalar variance is found to be altered for the intermediate molecular weight species as compared to the binary species case. The intermediate molecular weight species produces a substantially smaller scalar variance than the remaining species for all flows considered. For combustion of nonstoichiometric mixtures, a binary species mixture, characterized by stationary scalar states, results at long times after the lean reactant is depleted. The form of this final scalar distribution is observed to be similar to that found in the binary flow situation. A series of lower resolution simulations for a variety of species is then

Cyclodextrin based ternary system of modafinil: Effect of trimethyl chitosan and polyvinylpyrrolidone as complexing agents.

Science.gov (United States)

Patel, Parth; Agrawal, Y K; Sarvaiya, Jayrajsinh

2016-03-01

Modafinil is an approved drug for the treatment of narcolepsy and have a strong market presence in many countries. The drug is widely consumed for off-label uses and currently listed as a restricted drug. Modafinil has very low water solubility. To enhance the aqueous solubility of modafinil by the formation of a ternary complex with Hydroxypropyl-β-cyclodextrin and two hydrophilic polymers was the main objective of the present study. Pyrrolidone (PVP K30) and a water soluble chitosan derivative, trimethyl chitosan (TMC) were studied by solution state and solid state characterization methods for their discriminatory efficiency in solubility enhancement of modafinil. Phase solubility study depicted the highest complexation efficiency (2.22) of cyclodextrin derivative in the presence of TMC compared to the same in the presence of PVP K30 (0.08) and in the absence of any polymer (0.92). FT-IR analysis of binary and ternary complex expressed comparable contribution of both polymers in formation of inclusion complex. The thermal behaviour of binary and ternary complex, involving individual polymers disclosed the influence of TMC on polymorphism of the drug. DSC study revealed efficiency of TMC to prevent conversion of metastable polymorphic form to stable polymorphic form. Ternary complex, involving TMC enhanced water solubility of the drug 1.5 times more compared to the binary complex of the drug whereas PVP K30 reduced the Solubility. Copyright © 2015 Elsevier B.V. All rights reserved.

A Josephson ternary associative memory cell

International Nuclear Information System (INIS)

Morisue, M.; Suzuki, K.

1989-01-01

This paper describes a three-valued content addressable memory cell using a Josephson complementary ternary logic circuit named as JCTL. The memory cell proposed here can perform three operations of searching, writing and reading in ternary logic system. The principle of the memory circuit is illustrated in detail by using the threshold-characteristics of the JCTL. In order to investigate how a high performance operation can be achieved, computer simulations have been made. Simulation results show that the cycle time of memory operation is 120psec, power consumption is about 0.5 μW/cell and tolerances of writing and reading operation are +-15% and +-24%, respectively

Preparation and application of agar/alginate/collagen ternary blend functional food packaging films.

Science.gov (United States)

Wang, Long-Feng; Rhim, Jong-Whan

2015-09-01

Ternary blend agar/alginate/collagen (A/A/C) hydrogel films with silver nanoparticles (AgNPs) and grapefruit seed extract (GSE) were prepared. Their performance properties, transparency, tensile strength (TS), water vapor permeability (WVP), water contact angle (CA), water swelling ratio (SR), water solubility (WS), and antimicrobial activity were determined. The A/A/C film was highly transparent, and both AgNPs and GSE incorporated blend films (A/A/C(AgNPs) and A/A/C(GSE)) exhibited UV-screening effect, especially, the A/A/C(GSE) film had high UV-screening effect without sacrificing the transmittance. In addition, the A/A/C blend films formed efficient hydrogel film with the water holding capacity of 23.6 times of their weight. Both A/A/C(AgNPs) and A/A/C(GSE) composite films exhibited strong antimicrobial activity against both Gram-positive (Listeria monocytogenes) and Gram-negative (Escherichia coli) food-borne pathogenic bacteria. The test results of fresh potatoes packaging revealed that all the A/A/C ternary blend films prevented forming of condensed water on the packaged film surface, both A/A/C(AgNPs) and A/A/C(GSE) composite films prevented greening of potatoes during storage. The results indicate that the ternary blend hydrogel films incorporated with AgNPs or GSE can be used not only as antifogging packaging films for highly respiring fresh agriculture produce, but also as an active food packaging system utilizing their strong antimicrobial activity. Copyright © 2015 Elsevier B.V. All rights reserved.

Boosting the Visible-Light Photoactivity of BiOCl/BiVO4/N-GQD Ternary Heterojunctions Based on Internal Z-Scheme Charge Transfer of N-GQDs: Simultaneous Band Gap Narrowing and Carrier Lifetime Prolonging.

Science.gov (United States)

Zhu, Mingyue; Liu, Qian; Chen, Wei; Yin, Yuanyuan; Ge, Lan; Li, Henan; Wang, Kun

2017-11-08

The efficient separation of photogenerated electron-hole pairs in photoactive materials is highly desired, allowing their transfer to specific sites for undergoing redox reaction in various applications. The construction of ternary heterojunctions is a practical strategy to enhance the migration of photogenerated electron that realizes the synergistic effect of multicomponents rather than the simple overlay of single component. Here, we demonstrate an available way to fabricate new BiOCl/BiVO 4 /nitrogen-doped graphene quantum dot (N-GQD) ternary heterojunctions that exhibit higher efficiency in charge separation than any binary heterojunction or pure material under visible-light irradiation. UV-vis diffuse reflectance spectroscopy demonstrated that the proposed BiOCl/BiVO 4 /N-GQD ternary heterojunctions possess the narrower band gap energy. More importantly, the ternary heterojunctions reveal the prolonged lifetime of photogenerated charges and enhanced the separation efficiency of photogenerated electron-hole pairs, which may be ascribed to sensitization based on an internal Z-scheme charge transfer at the interface of N-GQDs with oxygen functional groups. Furthermore, we examine the photoactive performance of proposed ternary heterojunctions in aqueous solution by using the photodegradation of bisphenol A as a model system and BiOCl/BiVO 4 /N-GQD ternary heterojunctions also display a dramatically enhanced photodegradation rate. The proposed charge separation and transfer process of BiOCl/BiVO 4 /N-GQD ternary heterojunctions for the enhanced photoactivity were deduced by electrochemical measurements, photoluminescence, and electron spin resonance. The results demonstrate that a Z-scheme charge process was formed between BiOCl/BiVO 4 binary heterojunctions and N-GQDs, leading to an efficient charge carrier separation and strong photocatalytic ability. Notably, this work may assist in a better understanding of the role of N-GQDs in kinds of heterojunctions

Photovoltaic cells based on ternary P3HT:PCBM:polymethine dye active layer transparent in the visible range of light

Energy Technology Data Exchange (ETDEWEB)

Bliznyuk, Valery N., E-mail: vblizny@clemson.edu [Department of Materials Science and Engineering, Clemson University, Clemson, SC, 29634 (United States); Gasiorowski, Jacek [Semiconductor Physics, Technische Universität Chemnitz, D-09107 Chemnitz (Germany); Ishchenko, Alexander A.; Bulavko, Gennadiy V. [Institute of Organic Chemistry, National Academy of Sciences of Ukraine, 5 Murmanskaya str., Kiev 02660 (Ukraine); Rahaman, Mahfujur [Semiconductor Physics, Technische Universität Chemnitz, D-09107 Chemnitz (Germany); Hingerl, Kurt [Center for Interface and Nanoanalytics, Johannes Kepler University, Linz 4040 (Austria); Zahn, Dietrich R.T. [Semiconductor Physics, Technische Universität Chemnitz, D-09107 Chemnitz (Germany); Sariciftci, Niyazi S. [Linz Institute for Organic Solar Cells (LIOS), Physical Chemistry, Johannes Kepler University, Linz 4040 (Austria)

2016-12-15

Highlights: • Addition of a polymethine dye to P3HT:PCBM bulk-heterojunction (BHJ) films leads to a compositionally induced transparency in the system. • Variation of the complex refractive index in binary and ternary BHJ films has been studied with spectroscopic ellipsometry. • Power conversion efficiency of ternary BHJ solar cells is determined by the dye composition and photodoping. - Abstract: Optical and photovoltaic properties were studied for ternary photovoltaic cells containing a traditional donor-acceptor bulk-heterojunction (BHJ) active layer modified with polymethine dye molecules in a broad range of compositions and wavelengths. An effect of composition induced optical transparency, due to the strong modification of the density of states, was observed for symmetrical compositions with approximately equal amount of components. Based on our spectroscopic ellipsometry and atomic force microscopy (AFM) studies we can suggest that the variation of the refractive index, which is significantly reduced in the visible range for ternary systems, is involved in the physical mechanism of the phenomenon. Despite of an addition of the IR absorbing component (which allows broadening of the absorption band to up to 800 nm) no improvement in the power conversion efficiency (PCE) is observed in comparison to the binary BHJ system (P3HT:PCBM). Nevertheless, we believe that further advance of the efficiency will be possible if the energy levels will be chemically designed to avoid formation of charge traps at the BHJ interface during light excitation. Such fine adjustment of the system should become possible with a proper choice of polymer:dye composition due to a high versatility of the polymethine dyes demonstrated in previous studies.

Ternary q-Virasoro-Witt Hom-Nambu-Lie algebras

International Nuclear Information System (INIS)

Ammar, F; Makhlouf, A; Silvestrov, S

2010-01-01

In this paper we construct ternary q-Virasoro-Witt algebras which q-deform the ternary Virasoro-Witt algebras constructed by Curtright, Fairlie and Zachos using su(1, 1) enveloping algebra techniques. The ternary Virasoro-Witt algebras constructed by Curtright, Fairlie and Zachos depend on a parameter and are not Nambu-Lie algebras for all but finitely many values of this parameter. For the parameter values for which the ternary Virasoro-Witt algebras are Nambu-Lie, the corresponding ternary q-Virasoro-Witt algebras constructed in this paper are also Hom-Nambu-Lie because they are obtained from the ternary Nambu-Lie algebras using the composition method. For other parameter values this composition method does not yield a Hom-Nambu-Lie algebra structure for q-Virasoro-Witt algebras. We show however, using a different construction, that the ternary Virasoro-Witt algebras of Curtright, Fairlie and Zachos, as well as the general ternary q-Virasoro-Witt algebras we construct, carry a structure of the ternary Hom-Nambu-Lie algebra for all values of the involved parameters.

Ternary scandium and transition metals germanides

International Nuclear Information System (INIS)

Kotur, B.Ya.

1992-01-01

Brief review of data on phase diagram of ternary Sc-Me-Ge systems (Me-d - , f-transition element) is given. Isothermal sections at 870 and 1070 K of 17 ternary systems are plotted. Compositions and their structural characteristics are presented. Variability of crystal structure is typical for ternary scandium germanides: 70 compounds with the studied structure belong to 23 structural types. Ternary germanides isostructural to types of Sm 4 Ge 4 , ZrCrSi 2 , ZrNiAl, ScCeSi, TiNiSi U 4 Re 7 Si 6 145 compounds from 70 under investigation are mostly formed in studied systems

Efficient Mechanisms of Cooperation between Non-Governmental Organisations and Public Authorities

Directory of Open Access Journals (Sweden)

Rucsandra FILLOREANU

2015-09-01

Full Text Available This paper aims to present to the wide public a success story concerning the efficient cooperation between the civil society as a whole (citizens, NGOs, stake holders and public administration authorities. The success consists in using and strengthening dialogue measures within the collaboration of the two actors. The research is based on a study case. This was run through an EU funded project - “Efficient mechanisms of cooperation with public authorities”. The goal of the project was to increase the capacity of non-governmental organizations to cooperate with the public administration institutions. In order to reach the proposed aim there have been organized a series of theoretical and practical training courses, roundtable discussions and study-visits. Through this manner it has been encouraged and practiced the structured dialog on public agenda issues between the representatives of the local and national authorities and the active citizens. The outputs of the project consist in one Public Consultation Guide elaborated on the basis of good practices acknowledged through the project and two local citizens` initiatives on local public administration matters that have been brought into the public attention of the decision-making actors. Active citizenship, structured dialogue between civil society and state actors, developed tools for effective advocacy and lobby that are part of the success story that we intend to present through this study case.

Enhanced visible light-driven photocatalytic performance of ZnO–g-C_3N_4 coupled with graphene oxide as a novel ternary nanocomposite

International Nuclear Information System (INIS)

Jo, Wan-Kuen; Clament Sagaya Selvam, N.

2015-01-01

Highlights: • Prepared novel ternary nanocomposite consisting of ZnO, g-C_3N_4, and graphene oxide. • ZnO nanospheres disperse evenly and embed on porous g-C_3N_4-coupled graphene oxide. • Heterojunction of ternary composite account for the enhanced photocatalytic activity. - Abstract: This article reports a novel ternary nanocomposite consisting of ZnO, g-C_3N_4, and graphene oxide (GO) that provides enhanced photocatalytic performance and stability. The ZnO nanospheres disperse evenly and embed themselves in the porous g-C_3N_4. Composites with various g-C_3N_4 and GO to ZnO weight ratios were synthesized and characterized systematically. The results indicated that the absorption of binary g-C_3N_4/ZnO nanocomposites shifted to a lower energy compared to pure ZnO in a fashion consistent with the loading content of g-C_3N_4. Notably, the loading content of GO in the ZnO–g-C_3N_4 composite resulted in increased absorption in the visible range and improved charge separation efficiency, thereby drastically improving photocatalytic activity. Successful hybridization of ternary nanocomposite was confirmed by drastic quenching of fluorescence and broader visible light absorption. The optimal content of g-C_3N_4 in the ZnO–g-C_3N_4 composite was 50%, which exhibited the effective hybridization between ZnO and g-C_3N_4, and high photocatalytic efficiency. However, the photocatalytic degradation of the ternary nanocomposite showed performance that was two times greater than ZnO–g-C_3N_4, exhibiting 99.5% degradation efficiency after just 15 min of light irradiation. The combined heterojunction and synergistic effects of this composite account for the improved photocatalytic activity.

Graphene/Fe2O3/SnO2 ternary nanocomposites as a high-performance anode for lithium ion batteries.

Science.gov (United States)

Xia, Guofeng; Li, Ning; Li, Deyu; Liu, Ruiqing; Wang, Chen; Li, Qing; Lü, Xujie; Spendelow, Jacob S; Zhang, Junliang; Wu, Gang

2013-09-11

We report an rGO/Fe2O3/SnO2 ternary nanocomposite synthesized via homogeneous precipitation of Fe2O3 nanoparticles onto graphene oxide (GO) followed by reduction of GO with SnCl2. The reduction mechanism of GO with SnCl2 and the effects of reduction temperature and time were examined. Accompanying the reduction of GO, particles of SnO2 were deposited on the GO surface. In the graphene nanocomposite, Fe2O3 nanoparticles with a size of ∼20 nm were uniformly dispersed surrounded by SnO2 nanoparticles, as demonstrated by transmission electron microscopy analysis. Due to the different lithium insertion/extraction potentials, the major role of SnO2 nanoparticles is to prevent aggregation of Fe2O3 during the cycling. Graphene can serve as a matrix for Li+ and electron transport and is capable of relieving the stress that would otherwise accumulate in the Fe2O3 nanoparticles during Li uptake/release. In turn, the dispersion of nanoparticles on graphene can mitigate the restacking of graphene sheets. As a result, the electrochemical performance of rGO/Fe2O3/SnO2 ternary nanocomposite as an anode in Li ion batteries is significantly improved, showing high initial discharge and charge capacities of 1179 and 746 mAhg(-1), respectively. Importantly, nearly 100% discharge-charge efficiency is maintained during the subsequent 100 cycles with a specific capacity above 700 mAhg(-1).

Quantitative Structure-Relative Volatility Relationship Model for Extractive Distillation of Ethylbenzene/p-Xylene Mixtures: Application to Binary and Ternary Mixtures as Extractive Agents

Energy Technology Data Exchange (ETDEWEB)

Kang, Young-Mook; Oh, Kyunghwan; You, Hwan; No, Kyoung Tai [Bioinformatics and Molecular Design Research Center, Seoul (Korea, Republic of); Jeon, Yukwon; Shul, Yong-Gun; Hwang, Sung Bo; Shin, Hyun Kil; Kim, Min Sung; Kim, Namseok; Son, Hyoungjun [Yonsei University, Seoul (Korea, Republic of); Chu, Young Hwan [Sangji University, Wonju (Korea, Republic of); Cho, Kwang-Hwi [Soongsil University, Seoul (Korea, Republic of)

2016-04-15

Ethylbenzene (EB) and p-xylene (PX) are important chemicals for the production of industrial materials; accordingly, their efficient separation is desired, even though the difference in their boiling points is very small. This paper describes the efforts toward the identification of high-performance extractive agents for EB and PX separation by distillation. Most high-performance extractive agents contain halogen atoms, which present health hazards and are corrosive to distillation plates. To avoid this disadvantage of extractive agents, we developed a quantitative structure-relative volatility relationship (QSRVR) model for designing safe extractive agents. We have previously developed and reported QSRVR models for single extractive agents. In this study, we introduce extended QSRVR models for binary and ternary extractive agents. The QSRVR models accurately predict the relative volatilities of binary and ternary extractive agents. The service to predict the relative volatility for binary and ternary extractive agents is freely available from the Internet at http://qsrvr.o pengsi.org/.

Quantitative Structure-Relative Volatility Relationship Model for Extractive Distillation of Ethylbenzene/p-Xylene Mixtures: Application to Binary and Ternary Mixtures as Extractive Agents

International Nuclear Information System (INIS)

Kang, Young-Mook; Oh, Kyunghwan; You, Hwan; No, Kyoung Tai; Jeon, Yukwon; Shul, Yong-Gun; Hwang, Sung Bo; Shin, Hyun Kil; Kim, Min Sung; Kim, Namseok; Son, Hyoungjun; Chu, Young Hwan; Cho, Kwang-Hwi

2016-01-01

Ethylbenzene (EB) and p-xylene (PX) are important chemicals for the production of industrial materials; accordingly, their efficient separation is desired, even though the difference in their boiling points is very small. This paper describes the efforts toward the identification of high-performance extractive agents for EB and PX separation by distillation. Most high-performance extractive agents contain halogen atoms, which present health hazards and are corrosive to distillation plates. To avoid this disadvantage of extractive agents, we developed a quantitative structure-relative volatility relationship (QSRVR) model for designing safe extractive agents. We have previously developed and reported QSRVR models for single extractive agents. In this study, we introduce extended QSRVR models for binary and ternary extractive agents. The QSRVR models accurately predict the relative volatilities of binary and ternary extractive agents. The service to predict the relative volatility for binary and ternary extractive agents is freely available from the Internet at http://qsrvr.o pengsi.org/.

Design analysis of phosphor-free monolithic white light-emitting-diodes with InGaN/ InGaN multiple quantum wells on ternary InGaN substrates

Directory of Open Access Journals (Sweden)

Yu Kee Ooi

2015-05-01

Full Text Available Phosphor-free monolithic white light emitting diodes (LEDs based on InGaN/ InGaN multiple quantum wells (MQWs on ternary InGaN substrates are proposed and analyzed in this study. Simulation studies show that LED devices composed of multi-color-emitting InGaN/ InGaN quantum wells (QWs employing ternary InGaN substrate with engineered active region exhibit stable white color illumination with large output power (∼ 170 mW and high external quantum efficiency (EQE (∼ 50%. The chromaticity coordinate for the investigated monolithic white LED devices are located at (0.30, 0.28 with correlated color temperature (CCT of ∼ 8200 K at J = 50 A/cm2. A reference LED device without any nanostructure engineering exhibits green color emission shows that proper engineered structure is essential to achieve white color illumination. This proof-of-concept study demonstrates that high-efficiency and cost-effective phosphor-free monolithic white LED is feasible by the use of InGaN/ InGaN MQWs on ternary InGaN substrate combined with nanostructure engineering, which would be of great impact for solid state lighting.

Design analysis of phosphor-free monolithic white light-emitting-diodes with InGaN/ InGaN multiple quantum wells on ternary InGaN substrates

Energy Technology Data Exchange (ETDEWEB)

Ooi, Yu Kee, E-mail: Yu.Kee.Ooi@rit.edu; Zhang, Jing, E-mail: Jing.Zhang@rit.edu [Department of Electrical and Microelectronics Engineering, Rochester Institute of Technology, Rochester, New York 14623 (United States)

2015-05-15

Phosphor-free monolithic white light emitting diodes (LEDs) based on InGaN/ InGaN multiple quantum wells (MQWs) on ternary InGaN substrates are proposed and analyzed in this study. Simulation studies show that LED devices composed of multi-color-emitting InGaN/ InGaN quantum wells (QWs) employing ternary InGaN substrate with engineered active region exhibit stable white color illumination with large output power (∼ 170 mW) and high external quantum efficiency (EQE) (∼ 50%). The chromaticity coordinate for the investigated monolithic white LED devices are located at (0.30, 0.28) with correlated color temperature (CCT) of ∼ 8200 K at J = 50 A/cm{sup 2}. A reference LED device without any nanostructure engineering exhibits green color emission shows that proper engineered structure is essential to achieve white color illumination. This proof-of-concept study demonstrates that high-efficiency and cost-effective phosphor-free monolithic white LED is feasible by the use of InGaN/ InGaN MQWs on ternary InGaN substrate combined with nanostructure engineering, which would be of great impact for solid state lighting.

A spectrally efficient detect-and-forward scheme with two-tier adaptive cooperation

KAUST Repository

Benjillali, Mustapha

2011-09-01

We propose a simple relay-based adaptive cooperation scheme to improve the spectral efficiency of "Detect-and-Forward" (DetF) half-duplex relaying in fading channels. In a new common framework, we show that the proposed scheme offers considerable gainsin terms of the achievable information ratescompared to conventional DetF relaying schemes for both orthogonal and non-orthogonal source/relay transmissions. The analysis leads on to a general adaptive cooperation strategy based on the maximization of information rates at the destination which needs to observe only the average signal-to-noise ratios of the links. © 2006 IEEE.

US/Japan cooperation in high energy physics

Science.gov (United States)

1993-11-01

The objective of the Implementing Arrangement was to further the energy programs of both countries by establishing a framework for cooperation in the field of high energy physics, including research, accelerator and detector instrumentation research and development, the fabrication and subsequent use of new experimental devices and facilities, and related joint efforts as may be mutually agreed. Over the years, this cooperation has been very effective and has strengthened the overall collaborative efforts and the understanding between our nations and their citizens. It has demonstrated to the world our ability to work together to attack difficult problems. High Energy Physics goes across national borders; the bond is clearly intellectual and common ground is shared for the benefit of all in a most effective manner. This review covers the activities conducted under the aegis of the US/Japan Committee for Cooperation in High Energy Physics during the past five years (1988-1993). This was the second such US review of the US/Japan cooperative activities; the first was held in 1987.

Efficient visible-light photocatalytic activity by band alignment in mesoporous ternary polyoxometalate-Ag2S-CdS semiconductors

Science.gov (United States)

Kornarakis, I.; Lykakis, I. N.; Vordos, N.; Armatas, G. S.

2014-07-01

Porous multicomponent semiconductor materials show improved photocatalytic performance due to the large and accessible pore surface area and high charge separation efficiency. Here we report the synthesis of well-ordered porous polyoxometalate (POM)-Ag2S-CdS hybrid mesostructures featuring a controllable composition and high photocatalytic activity via a two-step hard-templating and topotactic ion-exchange chemical process. Ag2S compounds and polyoxometalate cluster anions with different reduction potentials, such as PW12O403-, SiW12O404- and PMo12O403-, were employed as electron acceptors in these ternary heterojunction photocatalysts. Characterization by small-angle X-ray scattering, X-ray diffraction, transmission electron microscopy and N2 physisorption measurements showed hexagonal arrays of POM-Ag2S-CdS hybrid nanorods with large internal BET surface areas and uniform mesopores. The Keggin structure of the incorporated POM clusters was also verified by elemental X-ray spectroscopy microanalysis, infrared and diffuse-reflectance ultraviolet-visible spectroscopy. These new porous materials were implemented as visible-light-driven photocatalysts, displaying exceptional high activity in aerobic oxidation of various para-substituted benzyl alcohols to the corresponding carbonyl compounds. Our experiments show that the spatial separation of photogenerated electrons and holes at CdS through the potential gradient along the CdS-Ag2S-POM interfaces is responsible for the increased photocatalytic activity.Porous multicomponent semiconductor materials show improved photocatalytic performance due to the large and accessible pore surface area and high charge separation efficiency. Here we report the synthesis of well-ordered porous polyoxometalate (POM)-Ag2S-CdS hybrid mesostructures featuring a controllable composition and high photocatalytic activity via a two-step hard-templating and topotactic ion-exchange chemical process. Ag2S compounds and polyoxometalate cluster

Cooperative procurement: market transformation for energy efficient products

Energy Technology Data Exchange (ETDEWEB)

Ostertag, K.; Dreher, C.

1999-07-01

Cooperative procurement is a variation of public purchasing which may be used as an instrument to transform the market and stimulate innovation enhancing environmental performance. The core of the procedure is the following: Coordinated by a central agency a group of buyers - public administrations, but also private companies, associations, etc. - gets together and jointly formulates a catalogue of performance requirements for a specific product truly suiting their preferences. This catalogue may contain (combinations of) requirements not yet available on the market and includes energy efficiency and/or environmental performance among other preferences important to the users. On the basis of the product requirements the buyer group launches a call for tenders, evaluates the bids received from the manufacturers and commits to buying the winning product. Thus, a market is provided for the most successful innovators in a given area of technology. The paper discusses the effectiveness of cooperative procurement as a policy instrument in the context of innovation theory and learning curves and it presents some empirical results on the feasibility of the transfer of this policy instruments to a wider range of European countries and/or to the European level. (orig.)

A novel ternary logic circuit using Josephson junction

International Nuclear Information System (INIS)

Morisue, M.; Oochi, K.; Nishizawa, M.

1989-01-01

This paper describes a novel Josephson complementary ternary logic circuit named as JCTL. This fundamental circuit is constructed by combination of two SQUIDs, one of which is switched in the positive direction and the other in the negative direction. The JCTL can perform the fundamental operations of AND, OR, NOT and Double NOT in ternary form. The principle of the operation and design criteria are described in detail. The results of the simulation show that the reliable operations of these circuits can be achieved with a high performance

Implementation of ternary Shor’s algorithm based on vibrational states of an ion in anharmonic potential

Science.gov (United States)

Liu, Wei; Chen, Shu-Ming; Zhang, Jian; Wu, Chun-Wang; Wu, Wei; Chen, Ping-Xing

2015-03-01

It is widely believed that Shor’s factoring algorithm provides a driving force to boost the quantum computing research. However, a serious obstacle to its binary implementation is the large number of quantum gates. Non-binary quantum computing is an efficient way to reduce the required number of elemental gates. Here, we propose optimization schemes for Shor’s algorithm implementation and take a ternary version for factorizing 21 as an example. The optimized factorization is achieved by a two-qutrit quantum circuit, which consists of only two single qutrit gates and one ternary controlled-NOT gate. This two-qutrit quantum circuit is then encoded into the nine lower vibrational states of an ion trapped in a weakly anharmonic potential. Optimal control theory (OCT) is employed to derive the manipulation electric field for transferring the encoded states. The ternary Shor’s algorithm can be implemented in one single step. Numerical simulation results show that the accuracy of the state transformations is about 0.9919. Project supported by the National Natural Science Foundation of China (Grant No. 61205108) and the High Performance Computing (HPC) Foundation of National University of Defense Technology, China.

Low-temperature solid-state preparation of ternary CdS/g-C3N4/CuS nanocomposites for enhanced visible-light photocatalytic H2-production activity

Science.gov (United States)

Cheng, Feiyue; Yin, Hui; Xiang, Quanjun

2017-01-01

Low-temperature solid-state method were gradually demonstrated as a high efficiency, energy saving and environmental protection strategy to fabricate composite semiconductor materials. CdS-based multiple composite photocatalytic materials have attracted increasing concern owning to the heterostructure constituents with tunable band gaps. In this study, the ternary CdS/g-C3N4/CuS composite photocatalysts were prepared by a facile and novel low-temperature solid-state strategy. The optimal ternary CdS/g-C3N4/CuS composite exhibits a high visible-light photocatalytic H2-production rate of 57.56 μmol h-1 with the corresponding apparent quantum efficiency reaches 16.5% at 420 nm with Na2S/Na2SO3 mixed aqueous solution as sacrificial agent. The ternary CdS/g-C3N4/CuS composites show the enhanced visible-light photocatalytic H2-evolution activity comparing with the binary CdS-based composites or simplex CdS. The enhanced photocatalytic activity is ascribed to the heterojunctions and the synergistic effect of CuS and g-C3N4 in promotion of the charge separation and charge mobility. This work shows that the low-temperature solid-state method is efficient and environmentally benign for the preparation of CdS-based multiple composite photocatalytic materials with enhanced visible-light photocatalytic H2-production activity.

Green Mobile Clouds: Network Coding and User Cooperation for Improved Energy Efficiency

DEFF Research Database (Denmark)

Heide, Janus; Fitzek, Frank; Pedersen, Morten Videbæk

2012-01-01

This paper highlights the benefits of user cooperation and network coding for energy saving in cellular networks. It is shown that these techniques allow for reliable and efficient multicast services from both a user and network perspective. The working principles and advantages in terms of energy...

Cooperation among strangers: an experiment with indefinite interaction

OpenAIRE

Gabriele Camera; Marco Casari

2007-01-01

We study the emergence of norms of cooperation in experimental economies populated by strangers interacting indefinitely and lacking formal enforcement institutions. In all treatments the efficient outcome is sustainable as an equilibrium. We address the following questions: can these economies achieve full efficiency? Which institutions for monitoring and enforcement promote cooperation? Finally, what classes of strategies are employed to achieve high efficiency? We find that, first, coopera...

A simple urea-based route to ternary metal oxynitride nanoparticles

International Nuclear Information System (INIS)

Gomathi, A.; Reshma, S.; Rao, C.N.R.

2009-01-01

Ternary metal oxynitrides are generally prepared by heating the corresponding metal oxides with ammonia for long durations at high temperatures. In order to find a simple route that avoids use of gaseous ammonia, we have employed urea as the nitriding agent. In this method, ternary metal oxynitrides are obtained by heating the corresponding metal carbonates and transition metal oxides with excess urea. By this route, ternary metal oxynitrides of the formulae MTaO 2 N (M=Ca, Sr or Ba), MNbO 2 N (M=Sr or Ba), LaTiO 2 N and SrMoO 3-x N x have been prepared successfully. The oxynitrides so obtained were generally in the form of nanoparticles, and were characterized by various physical techniques. - Graphical abstract: Nanoparticles of ternary metal oxynitrides can be synthesized by means of urea route. Given is the TEM image of the nanoparticles of CaTaO 2 N so obtained and the insets show the SAED pattern and HREM image of the nanoparticles

Self induced gratings in ternary SiO2:SnO2:Na2O bulk glasses by UV light seeding.

Science.gov (United States)

Lancry, M; Douay, M; Niay, P; Beclin, F; Menke, Y; Milanese, D; Ferraris, M; Poumellec, B

2005-09-05

The diffraction efficiency of gratings written in ternary SnO2:SiO2:Na2O bulk glasses rises dramatically with time after the occultation of the cw 244nm light used to write the thick hologram. This self-induced behavior lasts for several hours and ultimately leads to refractive index changes as high as 3 10-3.

Label-free peptide aptamer based impedimetric biosensor for highly sensitive detection of TNT with a ternary assembly layer.

Science.gov (United States)

Li, Yanyan; Zhao, Manru; Wang, Haiyan

2017-11-01

We report a label-free peptide aptamer based biosensor for highly sensitive detection of TNT which was designed with a ternary assembly layer consisting of anti-TNT peptide aptamer (peptamer), dithiothreitol (DTT), and 6-mercaptohexanol (MCH), forming Au/peptamer-DTT/MCH. A linear relationship between the change in electron transfer resistance and the logarithm of the TNT concentration from 0.44 to 18.92 pM, with a detection limit of 0.15 pM, was obtained. In comparison, the detection limit of the aptasensor with a common binary assembly layer (Au/peptamer/MCH) was 0.15 nM. The remarkable improvement in the detection limit could be ascribed to the crucial role of the ternary assembly layer, providing an OH-richer hydrophilic environment and a highly compact surface layer with minimal surface defects, reducing the non-covalent binding (physisorption) of the peptamer and non-specific adsorption of TNT onto the electrode surface, leading to high sensitivity, and which can serve as a general sensing platform for the fabrication of other biosensors.

5He, 7He, and 8Li (E*=2.26 MeV) intermediate ternary particles in the spontaneous fission of 252Cf

International Nuclear Information System (INIS)

Kopatch, Yu.N.; Mutterer, M.; Schwalm, D.; Thirolf, P.; Goennenwein, F.

2002-01-01

The neutron-unstable odd-N isotopes 5 He, 7 He, and 8 Li (in its excited state of E*=2.26 MeV) were measured to show up as short-lived (τ≅10 -21 -10 -20 s) intermediate light charged particles (LCPs) in ternary fission of 252 Cf. For the study a high-efficiency angular correlation measurement between neutrons, LCPs, and main fission fragments has been performed. The evidence for the ternary 5 He and 7 He particles (lifetimes: 1x10 -21 s, and 4x10 -21 s, respectively) was disclosed from the measured angular distributions of their decay neutrons focused by the emission in flight towards the direction of motion of 4 He and 6 He ternary particles. Similarly, neutrons observed to be peaked around Li-particle motion could be attributed to the decay of the second excited state at E*=2.26 MeV (lifetime: 2x10 -20 s) of 8 Li. The fractional yields of the intermediate 5 He and 7 He ternary fission modes relative to the 'true' ternary 4 He and 6 He modes, respectively, were determined to be 0.21(5) for both cases. The mean energy of the 4 He residues resulting from the 5 He decay was determined to be 12.4(3) MeV, compared to 15.7(2) MeV for all ternary α particles registered, and to 16.4(3) MeV for the true ternary α particles. The mean energy of the 6 He residues from the 7 He decay is 11.0(15) MeV, compared to 12.3(5) MeV for all ternary 6 He particles. The population of 8 Li* was deduced to be 0.06(2) relative to Li ternary fission, and 0.33(20) relative to the yield of particle stable 8 Li. The perspective of using the observed intermediate LCPs for probing the ternary scission configuration in 252 Cf fission with the aid of trajectory calculations is briefly discussed

5He, 7He and 8Li (E=2.26 MeV) intermediate ternary particles in the spontaneous fission of 252Cf

International Nuclear Information System (INIS)

Kopatch, Yu. N.; Goennenwein, F.

2002-02-01

The neutron-unstable odd-N isotopes 5 He, 7 He and 8 Li (in its excited state of E * = 2.26 MeV) were measured to show up as short-lived intermediate light-charged-particles (LCP) in ternary fission of 252 Cf. For the study a high-efficiency angular correlation measurement between neutrons, LCPs and main fission fragments has been performed. The evidence for the ternary 5 He and 7 He particles (lifetimes: 1 x 10 -21 s, and 4 x 10 -21 s, respectively) was disclosed from the measured angular distributions of their decay neutrons focused by the emission in flight towards the direction of motion of 4 He and 6 He ternary particles. Similarly, neutrons observed to be peaked around Li-particle motion could be attributed to the decay of the second excited state at E * = 2.26 MeV (lifetime: 2 x 10 -20 s) of 8 Li. The fractional yields of the intermediate 5 He and 7 He ternary fission modes relative to the ''true'' ternary 4 He and 6 He modes, respectively, were determined to be 0.21(5) for both cases. The mean energy of the 4 He residues resulting from the 5 He decay was determined to be 12.4(3) MeV, compared to 15.7(2) MeV for all ternary α-particles registered, and to 16.4(3) MeV for the true ternary α-particles. The mean energy of the 6 He residues from the 7 He decay is 11.0(15) MeV, compared to 12.3(5) MeV for all ternary 6 He particles. The population of 8 Li * was deduced to be 0.06(2) relative to Li ternary fission, and 0.33(20) relative to the yield of particle stable 8 Li. The perspective of using the observed intermediate LCPs for probing the ternary scission configuration in 252 Cf fission with the aid of trajectory calculations is briefly discussed. (orig.)

High efficiency steel filters for nuclear air cleaning

International Nuclear Information System (INIS)

Bergman, W.; Conner, J.; Larsen, G.; Lopez, R.; Turner, C.; Vahla, G.; Violet, C.; Williams, K.

1991-01-01

The authors have, in cooperation with industry, developed high-efficiency filters made from sintered stainless-steel fibers for use in several air-cleaning applications in the nuclear industry. These filters were developed to overcome the failure modes in present high-efficiently particulate air (HEPA) filters. HEPA filters are made from glass paper and glue, and they may fail when they get hot or wet and when they are overpressured. In developing steel filters, they first evaluated the commercially available stainless-steel filter media made from sintered powder and sintered fiber. The sintered-fiber media performed much better than sintered-powder media, and the best media had the smallest fiber diameter. Using the best media, prototype filters were then built for venting compressed gases and evaluated in their automated filter tester

Ag3PO4-TiO2-Graphene Oxide Ternary Composites with Efficient Photodegradation, Hydrogen Evolution, and Antibacterial Properties

Directory of Open Access Journals (Sweden)

Fu-Jye Sheu

2018-02-01

Full Text Available Ag3PO4-TiO2-graphene oxide ternary composite photocatalysts were fabricated by the photocatalytic reduction and ion exchange methods. The properties and photocatalytic activity of the composites were examined, and the photodegradation mechanism was investigated. More TiO2 nanoparticles in the composites were found to improve light absorption, but caused a larger impedance and inferior charge transport. Excess TiO2 nanoparticles distributed over the surfaces of Ag3PO4 and graphene oxide decreased the specific surface area and thus lowered light absorbance. An appropriate TiO2 content enhanced photocatalytic performance. When the molar ratio of Ag3PO4 to TiO2 was 0.6, the highest efficiency in photodegradation, hydrogen production (with a quantum efficiency of 8.1% and a hydrogen evolution rate of 218.7 μmole·g−1·h−1 and bacterial inactivation was achieved. Trapping experiments demonstrated that superoxide radicals and holes are the major active species involved in the photodegradation process.

Design of a novel quantum reversible ternary up-counter

Science.gov (United States)

Houshmand, Pouran; Haghparast, Majid

2015-08-01

Reversible logic has been recently considered as an interesting and important issue in designing combinational and sequential circuits. The combination of reversible logic and multi-valued logic can improve power dissipation, time and space utilization rate of designed circuits. Only few works have been reported about sequential reversible circuits and almost there are no paper exhibited about quantum ternary reversible counter. In this paper, first we designed 2-qutrit and 3-qutrit quantum reversible ternary up-counters using quantum ternary reversible T-flip-flop and quantum reversible ternary gates. Then we proposed generalized quantum reversible ternary n-qutrit up-counter. We also introduced a new approach for designing any type of n-qutrit ternary and reversible counter. According to the results, we can conclude that applying second approach quantum reversible ternary up-counter is better than the others.

Conditional imitation might promote cooperation under high temptations to defect

Science.gov (United States)

Dai, Qionglin; Li, Haihong; Cheng, Hongyan; Qian, Xiaolan; Zhang, Mei; Yang, Junzhong

2012-07-01

In this paper we introduce a conditional imitation rule into an evolutionary game, in which the imitation probabilities of individuals are determined by a function of payoff difference and two crucial parameters μ and σ. The parameter μ characterizes the most adequate goal for individuals and the parameter σ characterizes the tolerance of individuals. By using the pair approximation method and numerical simulations, we find an anomalous cooperation enhancement in which the cooperation level shows a nonmonotonic variation with the increase of temptation. The parameter μ affects the regime of the payoff parameter which supports the anomalous cooperation enhancement, whereas the parameter σ plays a decisive role on the appearance of the nonmonotonic variation of the cooperation level. Furthermore, to give explicit implications for the parameters μ and σ we present an alterative form of the conditional imitation rule based on the benefit and the cost incurred to individuals during strategy updates. In this way, we also provide a phenomenological interpretation for the nonmonotonic behavior of cooperation with the increase of temptation. The results give a clue that a higher cooperation level could be obtained under adverse environments for cooperation by applying the conditional imitation rule, which is possible to be manipulated in real life. More generally, the results in this work might point out an efficient way to maintain cooperation in the risky environments to cooperators.

The efficiency and socioeconomic effectiveness of the administration of the non Agricultural Cooperatives in Cuba

Directory of Open Access Journals (Sweden)

Odalys Labrador Machín

2016-12-01

Full Text Available The achievement of levels of efficiency and socioeconomic effectiveness, it constitutes a central objective of the economic politics of our Country. It is a vital topic for the redimensioning of the economic pattern that has not still had an answer from the theory and the Cuban managerial practice. In the I SAW Congress of the PCC and more recently the VII Congress, in those that were approved and they modernized the Limits of the Economic and Social Politics of the Party, the necessity is reaffirmed of to identify and potentialities and reservations that contribute the efficiency and effectiveness of the processes that are developed in all the administration forms to rise to take advantage. The paper of the cooperatives in the Cuban economy, demands to implement mechanisms that allow the evaluation of the efficiency and productive and social economic effectiveness that carry out, for that which is considered essential, to propose a system of indicators of efficiency and socioeconomic effectiveness in the non-Agricultural Cooperatives of Pinegrove of the River that it pays to reach positive results in the economic and social environment. In the work he/she is carried out a valuation of the concepts of efficiency, effectiveness and effectiveness and their importance for the cooperative administration, he/she intends a system of indicators of efficiency and effectiveness of the CNoA that it contributes to the improvement of their economic and social administration, with the intention of to contribute to the improvement of their administration process and to meditate on the elements that today interferes in its results and they attempt against the car sustainability of this companies.

Mechanical and water barrier properties of agar/κ-carrageenan/konjac glucomannan ternary blend biohydrogel films.

Science.gov (United States)

Rhim, Jong-Whan; Wang, Long-Feng

2013-07-01

Multicomponent hydrogel films composed of agar, κ-carrageenan, konjac glucomannan powder, and nanoclay (Cloisite(®) 30B) were prepared and their mechanical and water barrier properties such as water vapor permeability (WVP), water contact angle (CA), water solubility (WS), water uptake ratio (WUR), water vapor uptake ratio (WVUR) were determined. Mechanical, water vapor barrier, and water resistance properties of the ternary blend film exhibited middle range of individual component films, however, they increased significantly after formation of nanocomposite with the clay. Especially, the water holding capacity of the ternary blend biopolymer films increased tremendously, from 800% to 1681% of WUR for agar and κ-carrageenan films up to 5118% and 5488% of WUR for the ternary blend and ternary blend nanocomposite films, respectively. Water vapor adsorption behavior of films was also tested by water vapor adsorption kinetics and water vapor adsorption isotherms test. Preliminary test result for fresh spinach packaging revealed that the ternary blend biohydrogel films had a high potential for the use as an antifogging film for packaging highly respiring agricultural produce. In addition, the ternary blend nanocomposite film showed an antimicrobial activity against Gram-positive bacteria, Listeria monocytogenes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Identifying Cost-Effective Residential Energy Efficiency Opportunities for the Kauai Island Utility Cooperative

Energy Technology Data Exchange (ETDEWEB)

Busche, S.; Hockett, S.

2010-06-01

This analysis is an update to the 2005 Energy Efficiency Potential Study completed by KEMA for the Kauai Island Utility Cooperative (KIUC) and identifies potential energy efficiency opportunities in the residential sector on Kauai (KEMA 2005). The Total Resource Cost (TRC) test is used to determine which of the energy efficiency measures analyzed in the KEMA report are cost effective for KIUC to include in a residential energy efficiency program. This report finds that there remains potential energy efficiency savings that could be cost-effectively incentivized through a utility residential demand-side management program on Kauai if implemented in such a way that the program costs per measure are consistent with the current residential program costs.

Study on effect of L-arginine on solubility and dissolution of Zaltoprofen: Preparation and characterization of binary and ternary cyclodextrin inclusion complexes

Science.gov (United States)

Sherje, Atul P.; Patel, Forum; Murahari, Manikanta; Suvarna, Vasanti; Patel, Kavitkumar

2018-02-01

The present study demonstrated the binary and ternary complexes of Zaltoprofen (ZPF) with β-CD and HP-β-CD. The products were characterized using solubility, in vitro dissolution, and DSC studies. The mode of interaction of guest and host was revealed through 1H NMR and FT-IR studies. A significant increase was noticed in the stability constant (Kc) and complexation efficiency (CE) of β-CD and HP-β-CD due to addition of L-Arg in ternary complexes. The ternary complexes showed greater increase in solubility and dissolution of ZPF than binary complexes. Thus, ternary system of ZPF could be an innovative approach for its solubility and dissolution enhancement.

Green options for anti-corrosion of high strength concrete incorporating ternary pozzolan materials

Directory of Open Access Journals (Sweden)

Chen Yuan-Yuan

2017-01-01

Full Text Available This paper applied the densified mixture design algorithm(DMDA method by incorporating ternary pozzolans (fly ash, slag and silica fume; mix I and mix II to design high strength concrete (HSC mixtures with w/cm ratios from 0.24 to 0.30. Concrete without pozzolans was used as a control group (mix III, w/c from 0.24 to 0.30, and silica fume (5% was added as a substitute for part of the cement and set as mix IV. Experiments performed compressive strength, four-point resistance meter to measure the conductivity, and rapid chloride ion penetrability tests (ASTM C1202 were assessed the anti-corrosion. The life cycle inventory of LEED suggested by the PCA indicated the green options for cementitious materials. Results showed that mix I and II indicated cement used, CO2 reduction, raw materials and energy consumption all decreased more 50% than mix III, and mix IV was 5% less. The compressive strength and anti-corrosion levels showed that mix I and II were better than mix III and IV, and with ternary pozzolans could enhance the long-term durability (92 days due to a resistivity greater 20 KΩ-cm and a charge passed lower than 2000 Coulombs. HSC with an appropriate design could reduce the carbon footprint and improve the durability.

Efficient Cooperative Protocols for Full-Duplex Relaying over Nakagami-m Fading Channels

KAUST Repository

Khafagy, Mohammad Galal

2015-02-24

In this work, efficient protocols are studied for full-duplex relaying (FDR) with loopback interference over Nakagami-m block fading channels. Recently, a selective decodeand- forward (DF) protocol was proposed for FDR, and was shown to outperform existing protocols in terms of outage over Rayleigh-fading channels. In this work, we propose an incremental selective DF protocol that offers additional power savings, yet yields the same outage performance. We evaluate their outage performance over independent non-identically distributed Nakagami-m fading links, and study their relative performance in terms of the signal-to-noise ratio cumulative distribution function via closed-form expressions. The offered diversity gain is also derived. In addition, we study their performance relative to their half-duplex counterparts, as well as known non-selective FDR protocols. We corroborate our theoretical results with simulation, and confirm that selective cooperation protocols outperform the known non-selective protocols in terms of outage. Finally, we show that depending on the loopback interference level, the proposed protocols can outperform their half-duplex counterparts when high spectral efficiencies are targeted.

Efficient Cooperative Protocols for Full-Duplex Relaying over Nakagami-m Fading Channels

KAUST Repository

Khafagy, Mohammad Galal; Tammam, Amr; Alouini, Mohamed-Slim; Aissa, Sonia

2015-01-01

In this work, efficient protocols are studied for full-duplex relaying (FDR) with loopback interference over Nakagami-m block fading channels. Recently, a selective decodeand- forward (DF) protocol was proposed for FDR, and was shown to outperform existing protocols in terms of outage over Rayleigh-fading channels. In this work, we propose an incremental selective DF protocol that offers additional power savings, yet yields the same outage performance. We evaluate their outage performance over independent non-identically distributed Nakagami-m fading links, and study their relative performance in terms of the signal-to-noise ratio cumulative distribution function via closed-form expressions. The offered diversity gain is also derived. In addition, we study their performance relative to their half-duplex counterparts, as well as known non-selective FDR protocols. We corroborate our theoretical results with simulation, and confirm that selective cooperation protocols outperform the known non-selective protocols in terms of outage. Finally, we show that depending on the loopback interference level, the proposed protocols can outperform their half-duplex counterparts when high spectral efficiencies are targeted.

Search for new ternary Al, Ga or In containing phases using information forecasting system

International Nuclear Information System (INIS)

Kiseleva, N.N.; Burkhanov, G.S.

1989-01-01

Automated system of search for regularities in the formation of crystal phases and forecasting of new compounds with required properties, comprising data base on the properties of ternary inorganic compounds and cybernetic forecasting system, has been developed. General principles of operation of the developed information-forecasting system are considered. Efficiency of the system operation is shown, using as an example the search for new ternary compounds with aluminium, gallium and indium, crystallized in ZrNiAl, TiNiSi, ThCr 2 Si 2 , CaAl 2 Si 2 structural types. Results of the above-mentioned phases forecasting are shown

An improved ternary vector system for Agrobacterium-mediated rapid maize transformation.

Science.gov (United States)

Anand, Ajith; Bass, Steven H; Wu, Emily; Wang, Ning; McBride, Kevin E; Annaluru, Narayana; Miller, Michael; Hua, Mo; Jones, Todd J

2018-05-01

A simple and versatile ternary vector system that utilizes improved accessory plasmids for rapid maize transformation is described. This system facilitates high-throughput vector construction and plant transformation. The super binary plasmid pSB1 is a mainstay of maize transformation. However, the large size of the base vector makes it challenging to clone, the process of co-integration is cumbersome and inefficient, and some Agrobacterium strains are known to give rise to spontaneous mutants resistant to tetracycline. These limitations present substantial barriers to high throughput vector construction. Here we describe a smaller, simpler and versatile ternary vector system for maize transformation that utilizes improved accessory plasmids requiring no co-integration step. In addition, the newly described accessory plasmids have restored virulence genes found to be defective in pSB1, as well as added virulence genes. Testing of different configurations of the accessory plasmids in combination with T-DNA binary vector as ternary vectors nearly doubles both the raw transformation frequency and the number of transformation events of usable quality in difficult-to-transform maize inbreds. The newly described ternary vectors enabled the development of a rapid maize transformation method for elite inbreds. This vector system facilitated screening different origins of replication on the accessory plasmid and T-DNA vector, and four combinations were identified that have high (86-103%) raw transformation frequency in an elite maize inbred.

Ternary complex formation of lanthanides and radiolanthanides with phosphate and serum proteins

International Nuclear Information System (INIS)

Neumaier, B.; Roesch, F.

1999-01-01

Radioyttrium was recently reported to form ternary complexes with phosphate and serum proteins in blood. In the present work it was investigated whether the trivalent radiolanthanides react in a chemically similar way. In systematic binding studies using gel filtration a ternary complex formation between different lanthanides, phosphate and serum proteins could be identified. The tendency to build a ternary compound of the type Ln III - phosphate - serum protein, however, is dependent on the ionic radii of the lanthanides. Whereas the light and transition lanthanides have a strong inclination to build a ternary complex, this tendency is weaker for the heavier ones. Taking into account the high content of phosphate in human blood, the corresponding ternary complexes of radiolanthanides represent an important transport form of these elements in blood. This finding may contribute to an understanding of the nuclear medical observation on the biodistribution of radiolanthanides. The heavy radiolanthanides can be classified as bone seeking metals, whereas the light and transition lanthanide elements accumulate mainly in the liver and the spleen. For the lighter radiolanthanides the corresponding ternary complexes thus represent an important transport form in blood. This physicochemical form of lanthanides mainly results in reticulo endothelial accumulation; on the other hand, the lower tendency of heavier lanthanides leads to preferential skeletal deposition. (orig.)

Construction of RGO/CdIn2S4/g-C3N4 ternary hybrid with enhanced photocatalytic activity for the degradation of tetracycline hydrochloride

Science.gov (United States)

Xiao, Peng; Jiang, Deli; Ju, Lixin; Jing, Junjie; Chen, Min

2018-03-01

Although RGO shows great advantage in promoting charge separation and transfer of semiconductor, construction of an efficient RGO-incorporated photocatalyst is still challenging. Herein, RGO was employed to construct novel RGO/CdIn2S4/g-C3N4 (donated as RGO/CIS/CN) ternary photocatalyst by a facile hydrothermal method for the degradation of tetracycline hydrochloride (TC). The RGO/CIS/CN ternary photocatalyst showed significantly enhanced photocatalytic activity towards the degradation of TC as compared to the binary CIS/CN, CIS/CN, and CN/RGO. The photoluminescence and photocurrent response results indicate that this enhanced photocatalytic activity can be mainly ascribed to the improved charge separation and transfer efficiency. Based on the radical trapping and electron spin resonance results, the superoxide radicals and holes are proposed to play an important role in the degradation of TC over RGO/CIS/CN ternary photocatalyst. This work paves new opportunities for the synthesis of RGO-incorporated ternary photocatalyst as an efficient photocatalyst for the degradation of organic contaminant.

TernaryNet: faster deep model inference without GPUs for medical 3D segmentation using sparse and binary convolutions.

Science.gov (United States)

Heinrich, Mattias P; Blendowski, Max; Oktay, Ozan

2018-05-30

Deep convolutional neural networks (DCNN) are currently ubiquitous in medical imaging. While their versatility and high-quality results for common image analysis tasks including segmentation, localisation and prediction is astonishing, the large representational power comes at the cost of highly demanding computational effort. This limits their practical applications for image-guided interventions and diagnostic (point-of-care) support using mobile devices without graphics processing units (GPU). We propose a new scheme that approximates both trainable weights and neural activations in deep networks by ternary values and tackles the open question of backpropagation when dealing with non-differentiable functions. Our solution enables the removal of the expensive floating-point matrix multiplications throughout any convolutional neural network and replaces them by energy- and time-preserving binary operators and population counts. We evaluate our approach for the segmentation of the pancreas in CT. Here, our ternary approximation within a fully convolutional network leads to more than 90% memory reductions and high accuracy (without any post-processing) with a Dice overlap of 71.0% that comes close to the one obtained when using networks with high-precision weights and activations. We further provide a concept for sub-second inference without GPUs and demonstrate significant improvements in comparison with binary quantisation and without our proposed ternary hyperbolic tangent continuation. We present a key enabling technique for highly efficient DCNN inference without GPUs that will help to bring the advances of deep learning to practical clinical applications. It has also great promise for improving accuracies in large-scale medical data retrieval.

Sc-W-Si and Sc-W-Ge ternary systems

International Nuclear Information System (INIS)

Kotur, B.Ya.; Voznyak, O.M.; Bodak, O.I.

1989-01-01

Phase equilibria in Sc-W-Si and Sc-W-Ge ternary systems are investigated at 1070 K. Sc 2+x W 3-x Si 4 ternary compound (0≤x≤1) is determined, its crystal structure (Ce 2 Sc 3 Si 4 structural type), as well as, change of elementary cell parameters and microhardness within homogeneity range are determined. Regularities of component interaction within Sc-M-Si(Ge) (M-Cr, Mo, W) ternary system are determined. Ternary systems with Mo and W are more closer to each other according to the phase equilibria character, than to ternary systems with Cr

Performance Estimation for Lowpass Ternary Filters

Directory of Open Access Journals (Sweden)

Brenton Steele

2003-11-01

Full Text Available Ternary filters have tap values limited to −1, 0, or +1. This restriction in tap values greatly simplifies the multipliers required by the filter, making ternary filters very well suited to hardware implementations. Because they incorporate coarse quantisation, their performance is typically limited by tap quantisation error. This paper derives formulae for estimating the achievable performance of lowpass ternary filters, thereby allowing the number of computationally intensive design iterations to be reduced. Motivated by practical communications systems requirements, the performance measure which is used is the worst-case stopband attenuation.

Ternary gradient metal-organic frameworks.

Science.gov (United States)

Liu, Chong; Rosi, Nathaniel L

2017-09-08

Gradient MOFs contain directional gradients of either structure or functionality. We have successfully prepared two ternary gradient MOFs based on bMOF-100 analogues, namely bMOF-100/102/106 and bMOF-110/100/102, via cascade ligand exchange reactions. The cubic unit cell parameter discrepancy within an individual ternary gradient MOF crystal is as large as ∼1 nm, demonstrating the impressive compatibility and flexibility of the component MOF materials. Because of the presence of a continuum of unit cells, the pore diameters within individual crystals also change in a gradient fashion from ∼2.5 nm to ∼3.0 nm for bMOF-100/102/106, and from ∼2.2 nm to ∼2.7 nm for bMOF-110/100/102, indicating significant porosity gradients. Like previously reported binary gradient MOFs, the composition of the ternary gradient MOFs can be easily controlled by adjusting the reaction conditions. Finally, X-ray diffraction and microspectrophotometry were used to analyse fractured gradient MOF crystals by comparing unit cell parameters and absorbance spectra at different locations, thus revealing the profile of heterogeneity (i.e. gradient distribution of properties) and further confirming the formation of ternary gradient MOFs.

A comparative study of ternary Al-Sn-Cu immiscible alloys prepared by conventional casting and casting under high-intensity ultrasonic irradiation

Energy Technology Data Exchange (ETDEWEB)

Kotadia, H.R., E-mail: hiren.kotadia@kcl.ac.uk [Department of Physics, King' s College London, Strand, London WC2R 2LS (United Kingdom); Das, A. [Materials Research Centre, College of Engineering, Swansea University, Singleton Park, Swansea, SA2 8PP (United Kingdom); Doernberg, E.; Schmid-Fetzer, R. [Clausthal University of Technology, Institute of Metallurgy, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany)

2011-12-15

Highlights: Black-Right-Pointing-Pointer Systematic investigation on the solidification microstructure of ternary Al-Sn-Cu immiscible system aided by computational thermodynamics calculations. Black-Right-Pointing-Pointer Comparative study of conventional casting and casting under high-intensity ultrasonic irradiation. Black-Right-Pointing-Pointer Demonstrated the high effectiveness of ultrasound exposure during solidification. Black-Right-Pointing-Pointer Effect of cavitation on nucleation and the relative effects of cavitation and acoustic streaming on the dispersion of Sn-rich liquid phases have been explained from the experimental observation. Cavitation was found to promote fragmentation and dispersion of Sn-rich liquid leading to homogeneous dispersion of refined Sn phase. Microstructural modification was found to be contributed by cavitation and associated shockwave generation while bulk fluid flow under acoustic streaming was found to be less effective on the microstructure evolution. Black-Right-Pointing-Pointer Globular and highly refined {alpha}-Al formed near the radiator through enhanced heterogeneous nucleation in contrast to dendritic {alpha}-Al observed in conventional solidification. - Abstract: A comparative study on the microstructure of four ternary Al-Sn-Cu immiscible alloys, guided by the recent thermodynamic assessment of the system, was carried out with specific focus on the soft Sn particulate distribution in hard Al-rich matrix in the presence and absence of ultrasonic irradiation during solidification. The results clearly demonstrate high effectiveness of ultrasonication in promoting significantly refined and homogeneously dispersed microstructure, probably aided by enhanced nucleation and droplet fragmentation under cavitation. While conventional solidification produced highly segregated Sn phase at the centre and bottom of Sn-rich alloy ingots, ultrasonic treatment produced effective dispersion irrespective of the alloy constitution in

Design of ternary clocked adiabatic static random access memory

International Nuclear Information System (INIS)

Wang Pengjun; Mei Fengna

2011-01-01

Based on multi-valued logic, adiabatic circuits and the structure of ternary static random access memory (SRAM), a design scheme of a novel ternary clocked adiabatic SRAM is presented. The scheme adopts bootstrapped NMOS transistors, and an address decoder, a storage cell and a sense amplifier are charged and discharged in the adiabatic way, so the charges stored in the large switch capacitance of word lines, bit lines and the address decoder can be effectively restored to achieve energy recovery during reading and writing of ternary signals. The PSPICE simulation results indicate that the ternary clocked adiabatic SRAM has a correct logic function and low power consumption. Compared with ternary conventional SRAM, the average power consumption of the ternary adiabatic SRAM saves up to 68% in the same conditions. (semiconductor integrated circuits)

Design of ternary clocked adiabatic static random access memory

Science.gov (United States)

Pengjun, Wang; Fengna, Mei

2011-10-01

Based on multi-valued logic, adiabatic circuits and the structure of ternary static random access memory (SRAM), a design scheme of a novel ternary clocked adiabatic SRAM is presented. The scheme adopts bootstrapped NMOS transistors, and an address decoder, a storage cell and a sense amplifier are charged and discharged in the adiabatic way, so the charges stored in the large switch capacitance of word lines, bit lines and the address decoder can be effectively restored to achieve energy recovery during reading and writing of ternary signals. The PSPICE simulation results indicate that the ternary clocked adiabatic SRAM has a correct logic function and low power consumption. Compared with ternary conventional SRAM, the average power consumption of the ternary adiabatic SRAM saves up to 68% in the same conditions.

Temperature dependence of binary and ternary recombination of H3+ ions with electrons

International Nuclear Information System (INIS)

Glosik, J.; Plasil, R.; Korolov, I.; Kotrik, T.; Novotny, O.; Hlavenka, P.; Dohnal, P.; Varju, J.; Kokoouline, V.; Greene, Chris H.

2009-01-01

We study binary and the recently discovered process of ternary He-assisted recombination of H 3 + ions with electrons in a low-temperature afterglow plasma. The experiments are carried out over a broad range of pressures and temperatures of an afterglow plasma in a helium buffer gas. Binary and He-assisted ternary recombination are observed and the corresponding recombination rate coefficients are extracted for temperatures from 77 to 330 K. We describe the observed ternary recombination as a two-step mechanism: first, a rotationally excited long-lived neutral molecule H 3 * is formed in electron-H 3 + collisions. Second, the H 3 * molecule collides with a helium atom that leads to the formation of a very long-lived Rydberg state with high orbital momentum. We present calculations of the lifetimes of H 3 * and of the ternary recombination rate coefficients for para- and ortho-H 3 + . The calculations show a large difference between the ternary recombination rate coefficients of ortho- and para-H 3 + at temperatures below 300 K. The measured binary and ternary rate coefficients are in reasonable agreement with the calculated values.

Temperature dependence of binary and ternary recombination of H3+ ions with electrons

Science.gov (United States)

Glosík, J.; Plašil, R.; Korolov, I.; Kotrík, T.; Novotný, O.; Hlavenka, P.; Dohnal, P.; Varju, J.; Kokoouline, V.; Greene, Chris H.

2009-05-01

We study binary and the recently discovered process of ternary He-assisted recombination of H3+ ions with electrons in a low-temperature afterglow plasma. The experiments are carried out over a broad range of pressures and temperatures of an afterglow plasma in a helium buffer gas. Binary and He-assisted ternary recombination are observed and the corresponding recombination rate coefficients are extracted for temperatures from 77 to 330 K. We describe the observed ternary recombination as a two-step mechanism: first, a rotationally excited long-lived neutral molecule H3∗ is formed in electron- H3+ collisions. Second, the H3∗ molecule collides with a helium atom that leads to the formation of a very long-lived Rydberg state with high orbital momentum. We present calculations of the lifetimes of H3∗ and of the ternary recombination rate coefficients for para- and ortho- H3+ . The calculations show a large difference between the ternary recombination rate coefficients of ortho- and para- H3+ at temperatures below 300 K. The measured binary and ternary rate coefficients are in reasonable agreement with the calculated values.

A Computationally Efficient Equation of State for Ternary Gas Hydrate Systems

Science.gov (United States)

White, M. D.

2012-12-01

The potential energy resource of natural gas hydrates held in geologic accumulations, using lower volumetric estimates, is sufficient to meet the world demand for natural gas for nearly eight decades, at current rates of increase. As with other unconventional energy resources, the challenge is to economically produce the natural gas fuel. The gas hydrate challenge is principally technical. Meeting that challenge will require innovation, but more importantly, scientific research to understand the resource and its characteristics in porous media. The thermodynamic complexity of gas hydrate systems makes numerical simulation a particularly attractive research tool for understanding production strategies and experimental observations. Simply stated, producing natural gas from gas hydrate deposits requires releasing CH4 from solid gas hydrate. The conventional way to release CH4 is to dissociate the hydrate by changing the pressure and temperature conditions to those where the hydrate is unstable. Alternatively, the guest-molecule exchange technology releases CH4 by replacing it with more thermodynamically stable molecules (e.g., CO2, N2). This technology has three advantageous: 1) it sequesters greenhouse gas, 2) it potentially releases energy via an exothermic reaction, and 3) it retains the hydraulic and mechanical stability of the hydrate reservoir. Numerical simulation of the production of gas hydrates from geologic deposits requires accounting for coupled processes: multifluid flow, mobile and immobile phase appearances and disappearances, heat transfer, and multicomponent thermodynamics. The ternary gas hydrate system comprises five components (i.e., H2O, CH4, CO2, N2, and salt) and the potential for six phases (i.e., aqueous, nonaqueous liquid, gas, hydrate, ice, and precipitated salt). The equation of state for ternary hydrate systems has three requirements: 1) phase occurrence, 2) phase composition, and 3) phase properties. Numerical simulations that predict

Synthesis of CdS/ZnO/graphene composite with high-efficiency photoelectrochemical activities under solar radiation

International Nuclear Information System (INIS)

Han, Weijia; Ren, Long; Qi, Xiang; Liu, Yundan; Wei, Xiaolin; Huang, Zongyu; Zhong, Jianxin

2014-01-01

Graphical abstract: A graphene-based ternary composite was prepared by loading ZnO and CdS nanoparticles in graphene nanosheets via a facile one-pot hydrothermal process. The as-prepared ternary CdS/ZnO/graphene composite has shown excellent photoelectrochemical activity, which indicate that it may have a great potential application in photoelectrochemical hydrogen production from water reduction under sunlight. - Highlights: • A graphene-based ternary composite was prepared by loading ZnO and CdS nanoparticles in graphene nanosheets via a facile one-step hydrothermal method. • The CdS/ZnO/graphene composite demonstrated improved light-harvesting and superior durability photoelectrochemical activity. • The ternary composite can hinder the recombination of photo electrons and holes and improve charge transfer to enhance the photocatalytic activity. - Abstract: A novel ternary CdS/ZnO/graphene composite has been successfully prepared by loading ZnO and CdS nanoparticles in graphene nanosheets via a facile one-step hydrothermal method. The microstructures and properties have been examined by X-ray diffraction (XRD), scanning electron microscopy with an energy dispersive spectroscope (EDS), transmission electron microscopy, Raman and UV–vis diffuse reflectance spectra (DRS). The characterization results reveal that the crystalline of the composite is very well, the graphene sheets were tightly coated with ZnO and CdS nanoparticles, and the light-harvesting was effectively strengthened. Taking photoelectrochemical test, the ternary CdS/ZnO/graphene composite exhibits enhanced photocatalytic activity compared with its foundation matrix binary composites and pure ZnO and CdS. The improved photocatalytic performance can be attributed to the enhanced light absorption, the extremely efficient charge separation, as well as superior durability of the ternary composite. It is proposed that graphene-based composites by coupling graphene to suitable, multiple

The high efficiency steel filters for nuclear air cleaning

International Nuclear Information System (INIS)

Bergman, W.; Larsen, G.; Lopez, R.; Williams, K.; Violet, C.

1990-08-01

We have, in cooperation with industry, developed high-efficiency filters made from sintered stainless-steel fibers for use in several air-cleaning applications in the nuclear industry. These filters were developed to overcome the failure modes in present high-efficiency particulate air (HEPA) filters. HEPA filters are made from glass paper and glue, and they may fail when they get hot or wet and when they are overpressured. In developing our steel filters, we first evaluated the commercially available stainless-steel filter media made from sintered powder and sintered fiber. The sintered-fiber media performed much better than sintered-powder media, and the best media had the smallest fiber diameter. Using the best media, we then built prototype filters for venting compressed gases and evaluated them in our automated filter tester. 12 refs., 20 figs

Enhanced visible light-driven photocatalytic performance of ZnO–g-C{sub 3}N{sub 4} coupled with graphene oxide as a novel ternary nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Jo, Wan-Kuen; Clament Sagaya Selvam, N., E-mail: clamentloy@gmail.com

2015-12-15

Highlights: • Prepared novel ternary nanocomposite consisting of ZnO, g-C{sub 3}N{sub 4}, and graphene oxide. • ZnO nanospheres disperse evenly and embed on porous g-C{sub 3}N{sub 4}-coupled graphene oxide. • Heterojunction of ternary composite account for the enhanced photocatalytic activity. - Abstract: This article reports a novel ternary nanocomposite consisting of ZnO, g-C{sub 3}N{sub 4}, and graphene oxide (GO) that provides enhanced photocatalytic performance and stability. The ZnO nanospheres disperse evenly and embed themselves in the porous g-C{sub 3}N{sub 4}. Composites with various g-C{sub 3}N{sub 4} and GO to ZnO weight ratios were synthesized and characterized systematically. The results indicated that the absorption of binary g-C{sub 3}N{sub 4}/ZnO nanocomposites shifted to a lower energy compared to pure ZnO in a fashion consistent with the loading content of g-C{sub 3}N{sub 4}. Notably, the loading content of GO in the ZnO–g-C{sub 3}N{sub 4} composite resulted in increased absorption in the visible range and improved charge separation efficiency, thereby drastically improving photocatalytic activity. Successful hybridization of ternary nanocomposite was confirmed by drastic quenching of fluorescence and broader visible light absorption. The optimal content of g-C{sub 3}N{sub 4} in the ZnO–g-C{sub 3}N{sub 4} composite was 50%, which exhibited the effective hybridization between ZnO and g-C{sub 3}N{sub 4}, and high photocatalytic efficiency. However, the photocatalytic degradation of the ternary nanocomposite showed performance that was two times greater than ZnO–g-C{sub 3}N{sub 4}, exhibiting 99.5% degradation efficiency after just 15 min of light irradiation. The combined heterojunction and synergistic effects of this composite account for the improved photocatalytic activity.

A novel ternary content addressable memory design based on resistive random access memory with high intensity and low search energy

Science.gov (United States)

Han, Runze; Shen, Wensheng; Huang, Peng; Zhou, Zheng; Liu, Lifeng; Liu, Xiaoyan; Kang, Jinfeng

2018-04-01

A novel ternary content addressable memory (TCAM) design based on resistive random access memory (RRAM) is presented. Each TCAM cell consists of two parallel RRAM to both store and search for ternary data. The cell size of the proposed design is 8F2, enable a ∼60× cell area reduction compared with the conventional static random access memory (SRAM) based implementation. Simulation results also show that the search delay and energy consumption of the proposed design at the 64-bit word search are 2 ps and 0.18 fJ/bit/search respectively at 22 nm technology node, where significant improvements are achieved compared to previous works. The desired characteristics of RRAM for implementation of the high performance TCAM search chip are also discussed.

Susceptibility of ternary aluminum alloys to cracking during solidification

International Nuclear Information System (INIS)

Liu, Jiangwei; Kou, Sindo

2017-01-01

The crack susceptibility map of a ternary Al alloy system provides useful information about which alloy compositions are most susceptible to cracking and thus should be avoided by using a filler metal with a significantly different composition. In the present study the crack susceptibility maps of ternary Al alloy systems were calculated based on the maximum |dT/d(f S ) 1/2 | as an index for the crack susceptibility, where T is temperature and f S fraction solid. Due to the complexity associated with ternary alloy solidification, commercial thermodynamic software Pandat and Al database PanAluminum, instead of analytical equations, were used to calculate f S as a function of T and hence the maximum |dT/d(f S ) 1/2 | for ternary Al-Mg-Si, Al-Cu-Mg and Al-Cu-Si alloy systems. A crack susceptibility map covering 121 alloy compositions was constructed for each of the three ternary alloy systems at each of the following three levels of back diffusion: no back diffusion, back diffusion under a 100 °C/s cooling rate, and back diffusion under 20° C/s. The location of the region of high crack susceptibility, which is the most important part of the map, was shown in each of the nine calculated maps. These locations were compared with those observed in crack susceptibility tests by previous investigators. With back diffusion considered, either under 20 or 100 °C/s, the agreement between the calculated and observed maps was good especially for Al-Mg-Si and Al-Cu-Mg. Thus, the maximum |dT/d(f S ) 1/2 | can be used as a crack susceptibility index to construct crack susceptibility maps for ternary Al alloys and to evaluate the effect of back diffusion on their crack susceptibility. - Graphical abstract: The crack susceptibility map of a ternary alloy system indicates the composition range most susceptible to cracking, which should be avoided in welding or casting. The crack susceptibility maps of ternary Al alloy systems Al-Mg-Si, Al-Cu-Mg and Al-Cu-Si were calculated based

Thermodynamic modeling of the Ti-Al-Cr ternary system

International Nuclear Information System (INIS)

Chen Leyi; Qiu Aitao; Liu Lanjie; Jiang Ming; Lu Xionggang; Li Chonghe

2011-01-01

Research highlights: → The full experimental results of the Ti-Al-Cr ternary system and its sub-binary systems are reviewed and analysed in detail. → Based on the latest thermodynamic assessments of the Ti-Al, Ti-Cr and Al-Cr systems and the ternary experimental data in literature, the thermodynamic parameters of the Ti-Al-Cr ternary system are fully assessed by the Calphad method. → The transformation of disorder to order (bcc a 2 to B2) and the new ternary compound L 12T i 25 Cr 8 Al 67 are considered in this work. - Abstract: The Ti-Al-Cr ternary system is one of the most important systems to studying the titanium alloys. Some experimental data of this ternary system are available and a few partial thermodynamic assessments are reported. However, no full thermodynamic descriptions were published. In this study, the previous work on the Ti-Al-Cr system and its related binary systems are reviewed. Based on the thermodynamic descriptions of the Ti-Al, Ti-Cr and Al-Cr systems and the ternary experimental data in literature, the Ti-Al-Cr ternary system is assessed by means of the Calphad method. Several isothermal sections from 1073 K to 1573 K and some invariant reactions are calculated, which are in good agreement with the most of the experimental results.

Alternative Forms of International Cooperation: Comparing Their Efficiency

Science.gov (United States)

Tinbergen, Jan

1978-01-01

The author, an economist, discusses nine forms of international cooperation according to their strengths, and invites representatives of other disciplines to comment on international cooperation. Discusses relevant concepts and the estimation of optimal procedures for cooperation. Available from: Unipub, Box 433, Murray Hill Station, New York, New…

In vivo gene transfer using pDNA/chitosan/chondroitin sulfate ternary complexes: influence of chondroitin sulfate on the stability of freeze-dried complexes and transgene expression in vivo.

Science.gov (United States)

Hagiwara, Kenji; Kishimoto, Satoko; Ishihara, Masayuki; Koyama, Yoshiyuki; Mazda, Osam; Sato, Toshinori

2013-02-01

Chitosan has been investigated as a promising nonviral vector. However, several problems still remain, such as a relatively low transfection efficiency and instability under physiological conditions. We previously demonstrated that a chondroitin sulfate (CS) coating enhanced the transfection efficiency and physicochemical stability of plasmid DNA (pDNA)/chitosan complexes in vitro. In the present study, the effects of coating pDNA/chitosan complexes with CS on the stability in freeze-dry rehydration processes and gene expression in vivo were investigated. Freeze-drying storage at -20 °C, 4 °C, or room temperature, freezing storage at -20 °C, or liquid storage at 4 °C or room temperature, were examined for preservation conditions of pDNA/chitosan/CS ternary complexes by a gel retardation assay, measurements of sizes and zeta potentials, and a luciferase assay. Moreover, to determine the transfection efficiency of the ternary complexes in vivo, suicide gene therapy was carried out in Huh-7-implanted mice using herpes simplex virus thymidine kinase coding pDNA and ganciclovir. The freeze-dried pDNA/chitosan/CS ternary complexes showed sufficient cell transfection ability in vitro and in vivo. In addition, ternary complexes were associated with a significant suppression of tumor growth and a histopathologically high anti-tumor effect by intratumoral injection to tumor-bearing mice. The CS coating enhanced the preservation stability of the pDNA/chitosan complexes after freeze-drying-rehydration and their transgene expression in vivo. Copyright © 2013 John Wiley & Sons, Ltd.

Ternary cobalt-molybdenum-zirconium coatings for alternative energies

Science.gov (United States)

Yar-Mukhamedova, Gulmira; Ved', Maryna; Sakhnenko, Nikolay; Koziar, Maryna

2017-11-01

Consistent patterns for electrodeposition of Co-Mo-Zr coatings from polyligand citrate-pyrophosphate bath were investigated. The effect of both current density amplitude and pulse on/off time on the quality, composition and surface morphology of the galvanic alloys were determined. It was established the coating Co-Mo-Zr enrichment by molybdenum with current density increasing up to 8 A dm-2 as well as the rising of pulse time and pause duration promotes the content of molybdenum because of subsequent chemical reduction of its intermediate oxides by hydrogen ad-atoms. It was found that the content of the alloying metals in the coating Co-Mo-Zr depends on the current density and on/off times extremely and maximum Mo and Zr content corresponds to the current density interval 4-6 A dm-2, on-/off-time 2-10 ms. Chemical resistance of binary and ternary coatings based on cobalt is caused by the increased tendency to passivity and high resistance to pitting corrosion in the presence of molybdenum and zirconium, as well as the acid nature of their oxides. Binary coating with molybdenum content not less than 20 at.% and ternary ones with zirconium content in terms of corrosion deep index are in a group ;very proof;. It was shown that Co-Mo-Zr alloys exhibits the greatest level of catalytic properties as cathode material for hydrogen electrolytic production from acidic media which is not inferior a platinum electrode. The deposits Co-Mo-Zr with zirconium content 2-4 at.% demonstrate high catalytic properties in the carbon(II) oxide conversion. This confirms the efficiency of materials as catalysts for the gaseous wastes purification and gives the reason to recommend them as catalysts for red-ox processes activating by oxygen as well as electrode materials for red-ox batteries.

Experimental investigation of the Ag–Bi–I ternary system and thermodynamic properties of the ternary phases

International Nuclear Information System (INIS)

Mashadieva, Leyla F.; Aliev, Ziya S.; Shevelkov, Andrei V.; Babanly, Mahammad B.

2013-01-01

Highlights: ► The self-consistent phase diagram of the Ag–Bi–I system is constructed. ► Ag 2 BiI 5 and AgBi 2 I 7 are the only ternary phases of the system. ► Standard thermodynamic functions of formation and the standard entropies of Ag 2 BiI 5 and AgBi 2 I 7 are calculated. - Abstract: The phase equilibriums in the Ag–Bi–I ternary system and thermodynamic properties of the ternary phases were experimentally determined by using DTA and XRD techniques and EMF measurements with the Ag 4 RbI 5 solid electrolyte. According to the obtained experimental results, the polythermal sections of the ternary phase diagram, its isothermal section at 300 K as well as the projection of the liquids surface have been revised. The fields of the primary crystallization and types and coordinates of nonvariant and monovariant equilibriums were determined. The partial molar functions of silver iodide and silver in the alloys as well as the standard thermodynamic functions of formation and the standard entropies of Ag 2 BiI 5 and AgBi 2 I 7 were calculated based on EMF measurements.

Visible-light driven photocatalytic degradation of methylene-violet by rGO/Fe{sub 3}O{sub 4}/ZnO ternary nanohybrid structures

Energy Technology Data Exchange (ETDEWEB)

Thangavel, Srinivas [Nanomaterials Research Lab ( NmRL ), Department of Nanoscience and Technology, Karunya University, Coimbatore 641 114, Tamil Nadu (India); Center of Excellence in Advanced Materials and Green Technologies, Department of Chemical Engineering and Material Science, Amrita Vishwa Vidyapeetham, Coimbatore 641 112, Tamil Nadu (India); Thangavel, Sakthivel [Nanomaterials Research Lab ( NmRL ), Department of Nanoscience and Technology, Karunya University, Coimbatore 641 114, Tamil Nadu (India); Department of Mechanical Engineering, Jeju National University, Jeju 690-756 (Korea, Republic of); Raghavan, Nivea [Nanomaterials Research Lab ( NmRL ), Department of Nanoscience and Technology, Karunya University, Coimbatore 641 114, Tamil Nadu (India); Krishnamoorthy, Karthikeyan [Department of Mechanical Engineering, Jeju National University, Jeju 690-756 (Korea, Republic of); Venugopal, Gunasekaran, E-mail: gunasekaran@karunya.edu [Nanomaterials Research Lab ( NmRL ), Department of Nanoscience and Technology, Karunya University, Coimbatore 641 114, Tamil Nadu (India); Solid State Electronics Lab, Research Institute of Electrical Communication, Tohoku University, Katahira, Sendai 980-8577 (Japan)

2016-04-25

A novel ternary nanohybrid structure was constructed with reduced graphene-oxide/iron-oxide/zinc-oxide (rGO/Fe{sub 3}O{sub 4}/ZnO) via a facile hydrothermal method. The structural, morphological and optical properties were explored using X-ray diffraction, scanning electron microscope (SEM) with energy dispersive spectra and photoluminescence (PL) studies. The functional groups of ternary nanohybrid were characterized by Fourier transform-infrared spectroscopy. SEM images confirm the presence of two-dimensional GO sheets, one dimensional Fe{sub 3}O{sub 4} and ZnO nanorods. The PL spectra showed the quenching effect which has been observed from the reduction of electron–hole recombination in hybrid. Degradation efficiency of this system was evaluated and compared with pure ZnO and Fe{sub 3}O{sub 4}/ZnO. Under visible light condition, the ternary nanohybrid has shown an excellent photocatalytic degradation of methylene-violet dye. The degradation efficiency of rGO/Fe{sub 3}O{sub 4}/ZnO was systematically analyzed by absorption spectra and total organic carbon removal techniques. Our experimental results will show the potential way for the development of futuristic rGO based nanohybrids as an effective photocatalytic materials for waste-water treatment and environmental remedial applications. - Graphical abstract: A new ternary nanohybrid has been constructed with 1D Fe{sub 3}O{sub 4}–ZnO and 2D rGO sheets to utilize as visible-light photocatalyst. Highly active photocatalyst has been prepared by a feasible hydrothermal approach. For the first time, rGO/Fe{sub 3}O{sub 4}/ZnO ternary nanohybrid exhibits a superior photocatalytic activity towards the degradation of methylene-violet (dye) and the same can be used for environmental remediation applications. - Highlights: • Ternary nanohybrid constructed with 1D ZnO, Fe{sub 3}O{sub 4} and 2D rGO. • Aggregation free rGO/Fe{sub 3}O{sub 4}/ZnO nanohybrid exhibits superior photocatalytic activity. • rGO boost up

Robust tribo-mechanical and hot corrosion resistance of ultra-refractory Ta-Hf-C ternary alloy films.

Science.gov (United States)

Yate, Luis; Coy, L Emerson; Aperador, Willian

2017-06-08

In this work we report the hot corrosion properties of binary and ternary films of the Ta-Hf-C system in V 2 O 5 -Na 2 SO 4 (50%wt.-50%wt.) molten salts at 700 °C deposited on AISI D3 steel substrates. Additionally, the mechanical and nanowear properties of the films were studied. The results show that the ternary alloys consist of solid solutions of the TaC and HfC binary carbides. The ternary alloy films have higher hardness and elastic recoveries, reaching 26.2 GPa and 87%, respectively, and lower nanowear when compared to the binary films. The corrosion rates of the ternary alloys have a superior behavior compared to the binary films, with corrosion rates as low as 0.058 μm/year. The combination and tunability of high hardness, elastic recovery, low nanowear and an excellent resistance to high temperature corrosion demonstrates the potential of the ternary Ta-Hf-C alloy films for applications in extreme conditions.

True ternary fission of 252Cf

International Nuclear Information System (INIS)

Vijayaraghavan, K.R.; Balasubramaniam, M.; Oertzen, W. von

2014-01-01

Splitting of heavy radioactive nucleus into three fragments is known as ternary fission. If the size of the fragments are almost equal it is referred to as true ternary fission. Recently, Yu. V. Pyatkov et al observed/reported the experimental observation of true ternary fission in 252 Cf. In this work, the possibilities of different true ternary fission modes of 252 Cf through potential energy surface (PES) calculations based on three cluster model (TCM) are discussed. In TCM a condition on the mass numbers of the fission fragments is implied as A 1 ≥ A 2 ≥ A 3 in order to avoid repetition of combinations. Due to this condition, the values of Z 3 vary from 0 to 36 and Z 2 vary from 16 to 51. Of the different pairs having similar (Z 2 , Z 3 ) with different potential energy, a pair possessing minimum potential energy is chosen. Thus identified favourable combinations are plotted. For the PES calculations the arrangement of the fragments is considered in the order of A 1 +A 2 +A 3 . i.e. the heavy and the lightest fragments are kept at the ends. It is seen that the deepest minimum in the PES occurs for Z 3 =2 labelled as (Z 2 ; 2) indicating He accompanied breakup as the most favourable one. Of which, the breakup with Z 2 around 46 to 48 is the least (shown by dashed (Z 1 = 50) and dotted (Z 1 = 52) lines indicating a constant Z 1 value). The other notable minima in the PES are labelled and they correspond to the (Z 2 , Z 3 ) pairs viz., (20, 20), (28, 20), (28, 28) and (32, 32). Of these four minima, the first three are associated with the magic numbers 20 and 28. For Z 3 =20, there are two minimums at (20,20) and (28,20) among them (28,20) is the lowest minimum through which the minimum-path passes, and it is the ternary decay observed by Yu. V. Pyatkov et al. The fourth minima is the most interesting due to the fact that it corresponds to true ternary fission mode with Z 2 =32, Z 3 =32 and Z 1 =34. The minimum potential energy path also goes through this true

Ternary complex formation at mineral/solution interfaces

International Nuclear Information System (INIS)

Leckie, J.O.

1995-01-01

Adsorption of trace concentrations of radionuclides and heavy metals from aqueous solution is dependent on pH, absorbent and adsorbate concentration, and speciation of the metal in solution. In particular, complexation of metal ions by organic and inorganic ligands can dramatically alter adsorption behavior compared to ligand-free systems. The presence of complexing ligands can cause the formation of ''metal like'' or ''ligand like'' ternary surface complexes depending on whether adsorption of the ternary complex increases or decreases with increasing pH, respectively. Examples of ternary surface complexes behaving ''metal like'' include uranyl-EDTA surface complexes on goethite, neptunyl-EDTA surface complexes on hematite and neptunyl-humic surface complexes on gibbsite. Examples of ''ligand like'' ternary surface complexes include uranyl-carbonato and neptunyl-carbonato surface complexes on iron oxides. The effects of complex solutions and multimineralic systems are discussed. (authors). 39 refs., 16 figs., 8 tabs

Ternary carbide uranium fuels for advanced reactor design applications

International Nuclear Information System (INIS)

Knight, Travis; Anghaie, Samim

1999-01-01

Solid-solution mixed uranium/refractory metal carbides such as the pseudo-ternary carbide, (U, Zr, Nb)C, hold significant promise for advanced reactor design applications because of their high thermal conductivity and high melting point (typically greater than 3200 K). Additionally, because of their thermochemical stability in a hot-hydrogen environment, pseudo-ternary carbides have been investigated for potential space nuclear power and propulsion applications. However, their stability with regard to sodium and improved resistance to attack by water over uranium carbide portends their usefulness as a fuel for advanced terrestrial reactors. An investigation into processing techniques was conducted in order to produce a series of (U, Zr, Nb)C samples for characterization and testing. Samples with densities ranging from 91% to 95% of theoretical density were produced by cold pressing and sintering the mixed constituent carbides at temperatures as high as 2650 K. (author)

Equilibrium phase diagram of the Ag-Au-Pb ternary system

International Nuclear Information System (INIS)

Hassam, S.; Bahari, Z.

2005-01-01

The phase diagram of the ternary system Ag-Au-Pb has been established using differential thermal analysis and X-ray powder diffraction analysis. Four vertical sections were studied: X Pb = 0.40, X Au /X Pb = 1/3, X Ag /X Au = 4/1 and X Ag /X Au = 1/1. Two ternary transitory peritectics and one ternary eutectic were characterized. A schematic representation of the ternary equilibria is given

High performance gas adsorption and separation of natural gas in two microporous metal-organic frameworks with ternary building units.

Science.gov (United States)

Wang, Dongmei; Zhao, Tingting; Cao, Yu; Yao, Shuo; Li, Guanghua; Huo, Qisheng; Liu, Yunling

2014-08-14

Two novel MMOFs, JLU-Liu5 and JLU-Liu6, are based on ternary building units and exhibit high adsorption selectivity for CO2, C2H6 and C3H8 over CH4, which is attributed to steric effects and host-guest interactions. These MMOFs are promising materials for gas adsorption and natural gas purification.

Phase Equilibria of Sn-Co-Cu Ternary System

Science.gov (United States)

Chen, Yu-Kai; Hsu, Chia-Ming; Chen, Sinn-Wen; Chen, Chih-Ming; Huang, Yu-Chih

2012-10-01

Sn-Co-Cu ternary alloys are promising lead-free solders, and isothermal sections of Sn-Co-Cu phase equilibria are fundamentally important for the alloys' development and applications. Sn-Co-Cu ternary alloys were prepared and equilibrated at 523 K, 1073 K, and 1273 K (250 °C, 800 °C, and 1000 °C), and the equilibrium phases were experimentally determined. In addition to the terminal solid solutions and binary intermetallic compounds, a new ternary compound, Sn3Co2Cu8, was found. The solubilities of Cu in the α-CoSn3 and CoSn2 phases at 523 K (250 °C) are 4.2 and 1.6 at. pct, respectively, while the Cu solubility in the α-Co3Sn2 phase is as high as 20.0 at. pct. The Cu solubility increases with temperature and is around 30.0 at. pct in the β-Co3Sn2 at 1073 K (800 °C). The Co solubility in the η-Cu6Sn5 phase is also significant and is 15.5 at. pct at 523 K (250 °C).

Ternary networks reliability and Monte Carlo

CERN Document Server

Gertsbakh, Ilya; Vaisman, Radislav

2014-01-01

Ternary means “based on three”. This book deals with reliability investigations of  networks whose components subject to failures can be in three states –up, down and middle (mid), contrary to traditionally considered networks  having only binary (up/down) components. Extending binary case to ternary allows to consider more realistic and flexible models for communication, flow and supply networks.

Ternary fission induced by polarized neutrons

Directory of Open Access Journals (Sweden)

Gönnenwein Friedrich

2013-12-01

Full Text Available Ternary fission of (e,e U- and Pu- isotopes induced by cold polarized neutrons discloses some new facets of the process. In the so-called ROT effect shifts in the angular distributions of ternary particles relative to the fission fragments show up. In the so-called TRI effect an asymmetry in the emission of ternary particles relative to a plane formed by the fragment momentum and the spin of the neutron appear. The two effects are shown to be linked to the components of angular momentum perpendicular and parallel to the fission axis at the saddle point of fission. Based on theoretical models the spectroscopic properties of the collective transitional states at the saddle point are inferred from experiment.

Effective Electron Transfer Pathway of the Ternary TiO2/RGO/Ag Nanocomposite with Enhanced Photocatalytic Activity under Visible Light

Directory of Open Access Journals (Sweden)

Hongwei Tian

2017-05-01

Full Text Available Mesoporous TiO2/reduced graphene oxide/Ag (TiO2/RGO/Ag ternary nanocomposite with an effective electron transfer pathway is obtained by an electrostatic self-assembly method and photo-assisted treatment. Compared with bare mesoporous TiO2 (MT and mesoporous TiO2/RGO (MTG, the ternary mesoporous TiO2/RGO/Ag (MTGA nanocomposite exhibited superior photocatalytic performance for the degradation of methylene blue (MB under visible light, and the degradation rate reached 0.017 min−1, which was 3.4-times higher than that of MTG. What is more, the degradation rate of MTGA nanocomposite after three cycle times is 91.2%, and the composition is unchanged. In addition, we found that the OH•, h+ and especially O2•− contribute to the high photocatalytic activity of MTGA for MB degradation. It is proposed that Ag nanoparticles can form the local surface plasmon resonance (LSPR to absorb the visible light and distract the electrons into MT, and RGO can accept the electrons from MT to accelerate the separation efficiency of photogenerated carriers. The establishment of MTGA ternary nanocomposite makes the three components act synergistically to enhance the photocatalytic performance.

Ternary ceramic thermal spraying powder and method of manufacturing thermal sprayed coating using said powder

Energy Technology Data Exchange (ETDEWEB)

Vogli, Evelina; Sherman, Andrew J.; Glasgow, Curtis P.

2018-02-06

The invention describes a method for producing ternary and binary ceramic powders and their thermal spraying capable of manufacturing thermal sprayed coatings with superior properties. Powder contain at least 30% by weight ternary ceramic, at least 20% by weight binary molybdenum borides, at least one of the binary borides of Cr, Fe, Ni, W and Co and a maximum of 10% by weight of nano and submicro-sized boron nitride. The primary crystal phase of the manufactured thermal sprayed coatings from these powders is a ternary ceramic, while the secondary phases are binary ceramics. The coatings have extremely high resistance against corrosion of molten metal, extremely thermal shock resistance and superior tribological properties at low and at high temperatures.

Cognitive radio networks efficient resource allocation in cooperative sensing, cellular communications, high-speed vehicles, and smart grid

CERN Document Server

Jiang, Tao; Cao, Yang

2015-01-01

PrefaceAcknowledgmentsAbout the AuthorsIntroductionCognitive Radio-Based NetworksOpportunistic Spectrum Access NetworksCognitive Radio Networks with Cooperative SensingCognitive Radio Networks for Cellular CommunicationsCognitive Radio Networks for High-Speed VehiclesCognitive Radio Networks for a Smart GridContent and OrganizationTransmission Slot Allocation in an Opportunistic Spectrum Access NetworkSingle-User Single-Channel System ModelProbabilistic Slot Allocation SchemeOptimal Probabilistic Slot AllocationBaseline PerformanceExponential DistributionHyper-Erlang DistributionPerformance An

Malachite green mediates homodimerization of antibody VL domains to form a fluorescent ternary complex with singular symmetric interfaces

Science.gov (United States)

Szent-Gyorgyi, Chris; Stanfield, Robyn L.; Andreko, Susan; Dempsey, Alison; Ahmed, Mushtaq; Capek, Sara; Waggoner, Alan; Wilson, Ian A.; Bruchez, Marcel P.

2013-01-01

We report that a symmetric small molecule ligand mediates the assembly of antibody light chain variable domains (VLs) into a correspondent symmetric ternary complex with novel interfaces. The L5* Fluorogen Activating Protein (FAP) is a VL domain that binds malachite green dye (MG) to activate intense fluorescence. Crystallography of liganded L5* reveals a 2:1 protein:ligand complex with inclusive C2 symmetry, where MG is almost entirely encapsulated between an antiparallel arrangement of the two VL domains. Unliganded L5* VL domains crystallize as a similar antiparallel VL/VL homodimer. The complementarity determining regions (CDRs) are spatially oriented to form novel VL/VL and VL/ligand interfaces that tightly constrain a propeller conformer of MG. Binding equilibrium analysis suggests highly cooperative assembly to form a very stable VL/MG/VL complex, such that MG behaves as a strong chemical inducer of dimerization. Fusion of two VL domains into a single protein tightens MG binding over 1,000-fold to low picomolar affinity without altering the large binding enthalpy, suggesting that bonding interactions with ligand and restriction of domain movements make independent contributions to binding. Fluorescence activation of a symmetrical fluorogen provides a selection mechanism for the isolation and directed evolution of ternary complexes where unnatural symmetric binding interfaces are favored over canonical antibody interfaces. As exemplified by L5*, these self-reporting complexes may be useful as modulators of protein association or as high affinity protein tags and capture reagents. PMID:23978698

Description of light charged particle emission in ternary fission

International Nuclear Information System (INIS)

Andreev, A. V.; Adamian, G. G.; Antonenko, N. V.; Kuklin, S. N.; Scheid, W.

2010-01-01

We consider the motion of three fragments starting from the scission point of ternary system. In the alpha-accompanied ternary fission the initial conditions are not the free parameters and determined by minimization of potential energy at scission point. In the trajectory calculations the angular distribution and mean value of the kinetic energy of the alpha-particles are well described in the spontaneous ternary fission of 252 Cf. In the Be- and C-accompanied ternary fission we found that the emission of the third particle occurs from one of the heavy fragments after their separation. (authors)

Phase equilibria of the Mo-Al-Ho ternary system

Energy Technology Data Exchange (ETDEWEB)

Li, Yitai; Chen, Xiaoxian; Liu, Hao [Guangxi Univ., Nanning (China). College of Materials Science and Engineering; Guangxi Univ., Nanning (China). Guangxi Key Laboratory of Processing for Non-ferrous Metal and Featured Materials; Zhan, Yongzhong [Guangxi Univ., Nanning (China). College of Materials Science and Engineering; Guangxi Univ., Nanning (China). Guangxi Key Laboratory of Processing for Non-ferrous Metal and Featured Materials; Guangxi Univ., Nanning (China). Center of Ecological Collaborative Innovation for Aluminum Industry

2017-08-15

Investigation into the reactions and phase equilibria of transition metal elements (i.e. Mo, Zr, Cr, V and Ti), Al and rare earths is academically and industrially important for the development of both refractory alloys and lightweight high-temperature materials. In this work, the equilibria of the Mo-Al-Ho ternary system at 773 K have been determined by using X-ray powder diffraction and scanning electron microscopy equipped with energy dispersive X-ray analysis. A new ternary phase Al{sub 4}Mo{sub 2}Ho has been found and the other ternary phase Al{sub 43}Mo{sub 4}Ho{sub 6} is observed. Ten binary phases in the Al-Mo and Al-Ho systems, including Al{sub 17}Mo{sub 4} rather than Al{sub 4}Mo, have been determined to exist at 773 K. The homogeneity ranges of AlMo{sub 3} and Al{sub 8}Mo{sub 3} phase are 7.5 at.% and 1 at.%, respectively. According to the phase-disappearing method, the maximum solubility of Al in Mo is about 16 at.%.

Evaluation of ternary blended cements for use in transportation concrete structures

Science.gov (United States)

Gilliland, Amanda Louise

This thesis investigates the use of ternary blended cement concrete mixtures for transportation structures. The study documents technical properties of three concrete mixtures used in federally funded transportation projects in Utah, Kansas, and Michigan that used ternary blended cement concrete mixtures. Data were also collected from laboratory trial batches of ternary blended cement concrete mixtures with mixture designs similar to those of the field projects. The study presents the technical, economic, and environmental advantages of ternary blended cement mixtures. Different barriers of implementation for using ternary blended cement concrete mixtures in transportation projects are addressed. It was concluded that there are no technical, economic, or environmental barriers that exist when using most ternary blended cement concrete mixtures. The technical performance of the ternary blended concrete mixtures that were studied was always better than ordinary portland cement concrete mixtures. The ternary blended cements showed increased durability against chloride ion penetration, alkali silica reaction, and reaction to sulfates. These blends also had less linear shrinkage than ordinary portland cement concrete and met all strength requirements. The increased durability would likely reduce life cycle costs associated with concrete pavement and concrete bridge decks. The initial cost of ternary mixtures can be higher or lower than ordinary portland cement, depending on the supplementary cementitious materials used. Ternary blended cement concrete mixtures produce less carbon dioxide emissions than ordinary portland cement mixtures. This reduces the carbon footprint of construction projects. The barriers associated with implementing ternary blended cement concrete for transportation projects are not significant. Supplying fly ash returns any investment costs for the ready mix plant, including silos and other associated equipment. State specifications can make

Study of a ternary blend system for bulk heterojunction thin film solar cells

Science.gov (United States)

Ahmad, Zubair; Touati, Farid; Shakoor, R. A.; Al-Thani, N. J.

2016-08-01

In this research, we report a bulk heterojunction (BHJ) solar cell consisting of a ternary blend system. Poly(3-hexylthiophene) P3HT is used as a donor and [6,6]-phenyl C61-butyric acid methylester (PCBM) plays the role of acceptor whereas vanadyl 2,9,16,23-tetraphenoxy-29H, 31H-phthalocyanine (VOPcPhO) is selected as an ambipolar transport material. The materials are selected and assembled in such a fashion that the generated charge carriers could efficiently be transported rightwards within the blend. The organic BHJ solar cells consist of ITO/PEDOT:PSS/ternary BHJ blend/Al structure. The power conversion efficiencies of the ITO/ PEDOT:PSS/P3HT:PCBM/Al and ITO/PEDOT:PSS/ P3HT:PCBM:VOPcPhO/Al solar cells are found to be 2.3% and 3.4%, respectively. This publication was made possible by PDRA (Grant No. PDRA1-0117-14109) from the Qatar National Research Fund (a member of Qatar Foundation). The findings achieved herein are solely the responsibility of the authors.

Preparation of reduced graphene oxide/meso-TiO_2/AuNPs ternary composites and their visible-light-induced photocatalytic degradation n of methylene blue

International Nuclear Information System (INIS)

Yang, Yongfang; Ma, Zheng; Xu, Lidong; Wang, Hefang; Fu, Nian

2016-01-01

Graphical abstract: Reduced graphene oxide/meso-TiO_2/AuNPs (RGO/meso-TiO_2/AuNPs) ternary composites were prepared via the addition of graphene oxide to the dispersion of meso-TiO_2/AuNPs under a hydrothermal condition. The RGO/meso-TiO_2/AuNPs ternary composites show high photocatalytic activity toward MB. - Highlights: • RGO/meso-TiO_2/AuNPs were obtained by addition of graphene oxide to meso-TiO_2/AuNPs. • Au NPs in the mesopores of meso-TiO_2 reduce the recombination of charge carriers. • RGO covered with the surface of the meso-TiO_2 enhance the adsorption of MB. • RGO/meso-TiO_2/AuNPs composites show high photocatalytic performance toward MB. - Abstract: Reduced graphene oxide/meso-TiO_2/AuNPs (RGO/meso-TiO_2/AuNPs) ternary composites were prepared via the addition of graphene oxide to the dispersion of meso-TiO_2/AuNPs under hydrothermal conditions. The structure and the morphology of the RGO/meso-TiO_2/AuNPs materials were characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The photocatalytic activity of RGO/meso-TiO_2/AuNPs was evaluated by degradation of methyl blue (MB) under visible-light illumination. The ternary composites present an extended light absorption range, efficient charge separation properties, high adsorption ability for MB and high photocatalytic degradation activity of MB compared to the meso-TiO_2 and meso-TiO_2/AuNPs.

Ternary system of dihydroartemisinin with hydroxypropyl-β-cyclodextrin and lecithin: simultaneous enhancement of drug solubility and stability in aqueous solutions.

Science.gov (United States)

Wang, Dan; Li, Haiyan; Gu, Jingkai; Guo, Tao; Yang, Shuo; Guo, Zhen; Zhang, Xueju; Zhu, Weifeng; Zhang, Jiwen

2013-09-01

The purpose of this study was to simultaneously improve the solubility and stability of dihydroartemisinin (DHA) in aqueous solutions by a ternary cyclodextrin system comprised of DHA, hydroxypropyl-β-cyclodextrin (HP-β-CD) and a third auxiliary substance. Solubility and phase solubility studies were carried out to evaluate the solubilizing efficiency of HP-β-CD in association with various auxiliary substances. Then, the solid binary (DHA-HP-β-CD or DHA-lecithin) and ternary systems were prepared and characterized by Fourier transform infrared (FT-IR), differential scanning calorimetry (DSC) and power X-ray diffraction (PXRD). The effect of the ternary system on the solubility, dissolution and stability of DHA in aqueous solutions was also investigated. As a result, the soybean lecithin was found to be the most promising third component in terms of solubility enhancement. For the solid characterization, the disappearance of the drug crystallinity indicated the formation of new solid phases, implicating the formation of the ternary system. The dissolution rate of the solid ternary system was much faster than that of the drug alone and binary systems. Importantly, compared with binary systems, the ternary system showed a significant improvement in the stability of DHA in Hank's balanced salt solutions (pH 7.4). The solubility and stability of DHA in aqueous solutions were simultaneously enhanced by the ternary system, which might be attributed to the possible formation of a ternary complex. For the ternary interactions, results of molecular docking studies further indicated that the lecithin covered the top of the wide rim of HP-β-CD and surrounded around the peroxide bridging of DHA, providing the possibility for the ternary complex formation. In summary, the ternary system prepared in our study, with simultaneous enhancement of DHA solubility and stability in aqueous solutions, might have an important pharmaceutical potential in the development of a better

The ternary system nickel-boron-silicon

International Nuclear Information System (INIS)

Lugscheider, E.; Reimann, H.; Knotek, O.

1975-01-01

The ternary system Nickel-Boron-Silicon was established at 850 0 C by means of X-ray diffraction, metallographic and micro-hardness examinations. The well known binary nickel borides and silicides resp. were confirmed. In the boron-silicon system two binary phases, SiBsub(4-x) with x approximately 0.7 and SiB 6 were found the latter in equilibrium with the β-rhombohedral boron. Confirming the two ternary silicon borides a greater homogeneity range was found for Ni 6 Si 2 B, the phase Nisub(4,6)Si 2 B published by Uraz and Rundqvist can better be described by the formula Nisub(4.29)Si 2 Bsub(1.43). In relation to further investigations we measured melting temperatures in ternary Ni-10 B-Si alloys by differential thermoanalysis. (author)

Design of ternary low-power Domino JKL flip—flop and its application

International Nuclear Information System (INIS)

Wang Pengjun; Yang Qiankun; Zheng Xuesong

2012-01-01

By researching the ternary flip—flop and the adiabatic Domino circuit, a novel design of low-power ternary Domino JKL flip—flop on the switch level is proposed. First, the switch-level structure of the ternary adiabatic Domino JKL flip—flop is derived according to the switch-signal theory and its truth table. Then the ternary loop operation circuit and ternary reverse loop operation circuit are achieved by employing the ternary JKL flip—flop. Finally, the circuit is simulated by using the Spice tool and the results show that the logic function is correct. The energy consumption of the ternary adiabatic Domino JKL flip—flop is 69% less than its conventional Domino counterpart. (semiconductor integrated circuits)

Phase equilibria in M-X-X' and M-Al-X ternary systems (M-transition metal, X,X'-B,C,N,Si) and crystal chemistry of ternary compounds

International Nuclear Information System (INIS)

Gusev, A.I.

1996-01-01

The data on phase equilibria in the M-X-X' and M-Al-X ternary systems (M-transition metal of 3 to 8 groups, X-B,C, N, Si) have been considered and summarized. modern oxygen-free advanced ceramics is based on these ternary systems. Phase diagrams of the 130 ternary systems have been discussed, more than two hundred ternary phases forming in these systems have been systematized and described. The typical crystal structures of ternary compounds and phase have been considered, the common and distinctive features of these structures have been analysed. It has been shown that the ternary compounds with octahedral atomic groups XM 6 have a regions of homogeneity. Refs. 240

Integrated Ternary Bioinspired Nanocomposites via Synergistic Toughening of Reduced Graphene Oxide and Double-Walled Carbon Nanotubes.

Science.gov (United States)

Gong, Shanshan; Cui, Wei; Zhang, Qi; Cao, Anyuan; Jiang, Lei; Cheng, Qunfeng

2015-12-22

With its synergistic toughening effect and hierarchical micro/nanoscale structure, natural nacre sets a "gold standard" for nacre-inspired materials with integrated high strength and toughness. We demonstrated strong and tough ternary bioinspired nanocomposites through synergistic toughening of reduced graphene oxide and double-walled carbon nanotube (DWNT) and covalent bonding. The tensile strength and toughness of this kind of ternary bioinspired nanocomposites reaches 374.1 ± 22.8 MPa and 9.2 ± 0.8 MJ/m(3), which is 2.6 and 3.3 times that of pure reduced graphene oxide film, respectively. Furthermore, this ternary bioinspired nanocomposite has a high conductivity of 394.0 ± 6.8 S/cm and also shows excellent fatigue-resistant properties, which may enable this material to be used in aerospace, flexible energy devices, and artificial muscle. The synergistic building blocks with covalent bonding for constructing ternary bioinspired nanocomposites can serve as the basis of a strategy for the construction of integrated, high-performance, reduced graphene oxide (rGO)-based nanocomposites in the future.

Market competition and efficient cooperation

NARCIS (Netherlands)

Brandts, J.; Riedl, A.M.

2016-01-01

We use laboratory experiments to study the causal effects of favorable and unfavorable competitive market experience on cooperation in a subsequent social dilemma game. The issues we study are part of the broader topic of whether there are behavioral spillovers between different spheres of social

High-Pressure Phase Behavior of Polycaprolactone, Carbon Dioxide, and Dichloromethane Ternary Mixture Systems

Energy Technology Data Exchange (ETDEWEB)

Gwon, JungMin; Kim, Hwayong [Seoul National University, Seoul (Korea, Republic of); Shin, Hun Yong [Seoul National University of Science and Technology, Seoul (Korea, Republic of); Kim, Soo Hyun [Korea Institute of Science and Technology, Seoul (Korea, Republic of)

2015-04-15

The high-pressure phase behavior of a polycaprolactone (Mw=56,145 g/mol, polydispersity 1.2), dichloromethane, and carbon dioxide ternary system was measured using a variable-volume view cell. The experimental temperatures and pressures ranged from 313.15 K to 353.15 K and up to 300 bar as functions of the CO{sub 2}/dichloromethane mass ratio and temperature, at poly(D-lactic acid) weight fractions of 1.0, 2.0, and 3.0%. The correlation results were obtained from the hybrid equation of state (Peng-Robinson equation of state + SAFT equation of state) for the CO{sub 2}-polymer system using the van der Waals one-fluid mixing rule. The three binary interaction parameters were optimized by the simplex method algorithm.

Highly Efficient Electrocatalysts for Oxygen Reduction Reaction Based on 1D Ternary Doped Porous Carbons Derived from Carbon Nanotube Directed Conjugated Microporous Polymers

KAUST Repository

He, Yafei; Gehrig, Dominik; Zhang, Fan; Lu, Chenbao; Zhang, Chao; Cai, Ming; Wang, Yuanyuan; Laquai, Fré dé ric; Zhuang, Xiaodong; Feng, Xinliang

2016-01-01

© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.One-dimensional (1D) porous materials have shown great potential for gas storage and separation, sensing, energy storage, and conversion. However, the controlled approach for preparation of 1D porous materials, especially porous organic materials, still remains a great challenge due to the poor dispersibility and solution processability of the porous materials. Here, carbon nanotube (CNT) templated 1D conjugated microporous polymers (CMPs) are prepared using a layer-by-layer method. As-prepared CMPs possess high specific surface areas of up to 623 m2 g-1 and exhibit strong electronic interactions between p-type CMPs and n-type CNTs. The CMPs are used as precursors to produce heteroatom-doped 1D porous carbons through direct pyrolysis. As-produced ternary heteroatom-doped (B/N/S) 1D porous carbons possess high specific surface areas of up to 750 m2 g-1, hierarchical porous structures, and excellent electrochemical-catalytic performance for oxygen reduction reaction. Both of the diffusion-limited current density (4.4 mA cm-2) and electron transfer number (n = 3.8) for three-layered 1D porous carbons are superior to those for random 1D porous carbon. These results demonstrate that layered and core-shell type 1D CMPs and related heteroatom-doped 1D porous carbons can be rationally designed and controlled prepared for high performance energy-related applications.

Highly Efficient Electrocatalysts for Oxygen Reduction Reaction Based on 1D Ternary Doped Porous Carbons Derived from Carbon Nanotube Directed Conjugated Microporous Polymers

KAUST Repository

He, Yafei

2016-10-11

© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.One-dimensional (1D) porous materials have shown great potential for gas storage and separation, sensing, energy storage, and conversion. However, the controlled approach for preparation of 1D porous materials, especially porous organic materials, still remains a great challenge due to the poor dispersibility and solution processability of the porous materials. Here, carbon nanotube (CNT) templated 1D conjugated microporous polymers (CMPs) are prepared using a layer-by-layer method. As-prepared CMPs possess high specific surface areas of up to 623 m2 g-1 and exhibit strong electronic interactions between p-type CMPs and n-type CNTs. The CMPs are used as precursors to produce heteroatom-doped 1D porous carbons through direct pyrolysis. As-produced ternary heteroatom-doped (B/N/S) 1D porous carbons possess high specific surface areas of up to 750 m2 g-1, hierarchical porous structures, and excellent electrochemical-catalytic performance for oxygen reduction reaction. Both of the diffusion-limited current density (4.4 mA cm-2) and electron transfer number (n = 3.8) for three-layered 1D porous carbons are superior to those for random 1D porous carbon. These results demonstrate that layered and core-shell type 1D CMPs and related heteroatom-doped 1D porous carbons can be rationally designed and controlled prepared for high performance energy-related applications.

From Large-Scale Synthesis to Lighting Device Applications of Ternary I-III-VI Semiconductor Nanocrystals: Inspiring Greener Material Emitters.

Science.gov (United States)

Chen, Bingkun; Pradhan, Narayan; Zhong, Haizheng

2018-01-18

Quantum dots with fabulous size-dependent and color-tunable emissions remained as one of the most exciting inventories in nanomaterials for the last 3 decades. Even though a large number of such dot nanocrystals were developed, CdSe still remained as unbeatable and highly trusted lighting nanocrystals. Beyond these, the ternary I-III-VI family of nanocrystals emerged as the most widely accepted greener materials with efficient emissions tunable in visible as well as NIR spectral windows. These bring the high possibility of their implementation as lighting materials acceptable to the community and also to the environment. Keeping these in mind, in this Perspective, the latest developments of ternary I-III-VI nanocrystals from their large-scale synthesis to device applications are presented. Incorporating ZnS, tuning the composition, mixing with other nanocrystals, and doping with Mn ions, light-emitting devices of single color as well as for generating white light emissions are also discussed. In addition, the future prospects of these materials in lighting applications are also proposed.

Role of ternary fission in synthesis of bypassed nuclei

International Nuclear Information System (INIS)

Kramarovskij, Ya.M.; Chechev, V.P.

1983-01-01

A possible influence of ternary fission with escape of neutron-enriched light charged particles on the synthesis of bypassed nuclides is considered. It is shown that this concept cannot give explanation of bypassed isotope concentrations, but it can make some contribution, if the probability of ternary fission for superheavy nuclei grows sharply with Z 2 /A parameter. The account of β-delayed fission contributes to the shift of ternary fission fragments into the region of neutron-deficient isotopes. Consistent consideration of the ternary fission role in the nucleosynthesis is possible only with an important accumulation of experimental and theoretical data on this process, particularly for the nuclei with Z > 100

Double Z-scheme ZnO/ZnS/g-C3N4 ternary structure for efficient photocatalytic H2 production

Science.gov (United States)

Dong, Zhifang; Wu, Yan; Thirugnanam, Natarajan; Li, Gonglin

2018-02-01

In the present work, a novel ZnO/ZnS/g-C3N4 ternary nanocomposite with double Z-scheme heterojunction has been designed via a two-step facile chemical conversion route. The spherical ZnS nanoparticles were uniformly loaded onto ZnO nanoflowers surface. And then the ZnO/ZnS nanocomposite was further hybridized with g-C3N4 nanosheets. Ternary ZnO/ZnS/g-C3N4 nanocomposite displays the largest specific surface area (about 76.2 m2/g), which provides plentiful activated sites for photocatalytic reaction. Furthermore, the ternary material exhibits the highest methylene blue photodegradation rate of about 0.0218 min-1 and the optimum photocatalytic H2 production (1205 μmol/g) over water splitting at 4 h under solar light irradiation. Moreover, it showed the highest photocurrent effect and the minimum charge-transfer resistance. These results implied that the higher photoactivity of ZnO/ZnS/g-C3N4 nanocomposite could be attributed to the multi-steps charge transfer and effective electron-hole separation in the double Z-scheme system.

[Spectral Analysis of CdZnSe Ternary Quantum Dots Sensitized TiO2 Tubes and Its Application in Visible-Light Photocatalysis].

Science.gov (United States)

Han, Zhi-zhong; Ren, Li-li; Pan, Hai-bo; Li, Chun-yan; Chen, Jing-hua; Chen, Jian-zhong

2015-11-01

In this work, cadmium nitrate hexahydrate [Cd(NO₃)₂ · 6H₂O] is as a source of cadmium, zinc nitrate [Zn(NO₃)₂] as a source of zinc source, and NaHSe as a source of selenium which was prepared through reducing the elemental selenium with sodium borohydride (NaBH₄). Then water-soluble Cd₁₋xZnxSe ternary quantum dots with different component were prepared by colloid chemistry. The as-prepared Cd₁₋xZnx Se ternary quantum dots exhibit stable fluorescent property in aqueous solution, and can still maintain good dispersivity at room temperature for four months. Powder X-ray diffraction (XRD) and high resolution transmission electron microscope (HRTEM) were used to analyze crystal structure and morphology of the prepared Cd₁₋xZnxSe. It is found that the as-prepared ternary quantum dots are cubic phase, show as sphere, and the average of particle size is approximate 4 nm. The spectral properties and energy band structure of the as-prepared ternary quantum dots were modulated through changing the atom ratio of elements Zn and Cd. Compared with binary quantum dots CdSe and ZnSe, the ultraviolet-visible (UV-Visible) absorption spectrum and fluorescence (FL) emission spectrum of ternary quantum dots are both red-shift. The composites (Cd₀.₅ Zn₀.₅ Se@TNTs) of Cd₀.₅ Zn₀.₅ Se ternary quantum dots and TiO₂ nanotubes (TNTs) were prepared by directly immerging TNTs into quantum dots dispersive solution for 5 hours. TEM image shows that the Cd₀.₅ Zn₀.₅ Se ternary quantum dots were closely combined to nanotube surface. The infrared spectra show that the Ti-Se bond was formed between Cd₀.₅ Zn₀.₅ Se ternary quantum dots and TiO₂ nanotubes, which improve the stability of the composite. Compared to pristine TNTs, UV-Visible absorption spectrum of the composites is significantly enhanced in the visible region of light. And the absorption band edge of Cd₀.₅Zn₀.₅ Se@TNTs red-shift from 400 to 700 nm. The recombination of the

Advisory and autonomous cooperative driving systems

NARCIS (Netherlands)

Broek, T.H.A. van den; Ploeg, J.; Netten, B.D.

2011-01-01

In this paper, the traffic efficiency of an advisory cooperative driving system, Advisory Acceleration Control is examined and compared to the efficiency of an autonomous cooperative driving system, Cooperative Adaptive Cruise Control. The algorithms and implementation thereof are explained. The

Hardware emulation of Memristor based Ternary Content Addressable Memory

KAUST Repository

Bahloul, Mohamed A.

2017-12-13

MTCAM (Memristor Ternary Content Addressable Memory) is a special purpose storage medium in which data could be retrieved based on the stored content. Using Memristors as the main storage element provides the potential of achieving higher density and more efficient solutions than conventional methods. A key missing item in the validation of such approaches is the wide spread availability of hardware emulation platforms that can provide reliable and repeatable performance statistics. In this paper, we present a hardware MTCAM emulation based on 2-Transistors-2Memristors (2T2M) bit-cell. It builds on a bipolar memristor model with storing and fetching capabilities based on the actual current-voltage behaviour. The proposed design offers a flexible verification environment with quick design revisions, high execution speeds and powerful debugging techniques. The proposed design is modeled using VHDL and prototyped on Xilinx Virtex® FPGA.

Hardware emulation of Memristor based Ternary Content Addressable Memory

KAUST Repository

Bahloul, Mohamed A.; Naous, Rawan; Masmoudi, M.

2017-01-01

MTCAM (Memristor Ternary Content Addressable Memory) is a special purpose storage medium in which data could be retrieved based on the stored content. Using Memristors as the main storage element provides the potential of achieving higher density and more efficient solutions than conventional methods. A key missing item in the validation of such approaches is the wide spread availability of hardware emulation platforms that can provide reliable and repeatable performance statistics. In this paper, we present a hardware MTCAM emulation based on 2-Transistors-2Memristors (2T2M) bit-cell. It builds on a bipolar memristor model with storing and fetching capabilities based on the actual current-voltage behaviour. The proposed design offers a flexible verification environment with quick design revisions, high execution speeds and powerful debugging techniques. The proposed design is modeled using VHDL and prototyped on Xilinx Virtex® FPGA.

Morphology-Tuned Synthesis of Nickel Cobalt Selenides as Highly Efficient Pt-Free Counter Electrode Catalysts for Dye-Sensitized Solar Cells.

Science.gov (United States)

Qian, Xing; Li, Hongmei; Shao, Li; Jiang, Xiancai; Hou, Linxi

2016-11-02

In this work, morphology-tuned ternary nickel cobalt selenides based on different Ni/Co molar ratios have been synthesized via a simple precursor conversion method and used as counter electrode (CE) materials for dye-sensitized solar cells (DSSCs). The experimental facts and mechanism analysis clarified the possible growth process of product. It can be found that the electrochemical performance and structures of ternary nickel cobalt selenides can be optimized by tuning the Ni/Co molar ratio. Benefiting from the unique morphology and tunable composition, among the as-prepared metal selenides, the electrochemical measurements showed that the ternary nickel cobalt selenides exhibited a more superior electrocatalytic activity in comparison with binary Ni and Co selenides. In particular, the three-dimensional dandelion-like Ni 0.33 Co 0.67 Se microspheres delivered much higher power conversion efficiency (9.01%) than that of Pt catalyst (8.30%) under AM 1.5G irradiation.

Synthesis of CdS/ZnO/graphene composite with high-efficiency photoelectrochemical activities under solar radiation

Science.gov (United States)

Han, Weijia; Ren, Long; Qi, Xiang; Liu, Yundan; Wei, Xiaolin; Huang, Zongyu; Zhong, Jianxin

2014-04-01

A novel ternary CdS/ZnO/graphene composite has been successfully prepared by loading ZnO and CdS nanoparticles in graphene nanosheets via a facile one-step hydrothermal method. The microstructures and properties have been examined by X-ray diffraction (XRD), scanning electron microscopy with an energy dispersive spectroscope (EDS), transmission electron microscopy, Raman and UV-vis diffuse reflectance spectra (DRS). The characterization results reveal that the crystalline of the composite is very well, the graphene sheets were tightly coated with ZnO and CdS nanoparticles, and the light-harvesting was effectively strengthened. Taking photoelectrochemical test, the ternary CdS/ZnO/graphene composite exhibits enhanced photocatalytic activity compared with its foundation matrix binary composites and pure ZnO and CdS. The improved photocatalytic performance can be attributed to the enhanced light absorption, the extremely efficient charge separation, as well as superior durability of the ternary composite. It is proposed that graphene-based composites by coupling graphene to suitable, multiple semiconductors can not only greatly improve the capacity for photocatalytic, but also expand the exploration and utilization of graphene-based nanocomposites for energy conversion.

Energy Efficient Cooperative Spectrum Sensing in Cognitive Radio Networks Using Distributed Dynamic Load Balanced Clustering Scheme

Directory of Open Access Journals (Sweden)

Muthukkumar R.

2017-04-01

Full Text Available Cognitive Radio (CR is a promising and potential technique to enable secondary users (SUs or unlicenced users to exploit the unused spectrum resources effectively possessed by primary users (PUs or licenced users. The proven clustering approach is used to organize nodes in the network into the logical groups to attain energy efficiency, network scalability, and stability for improving the sensing accuracy in CR through cooperative spectrum sensing (CSS. In this paper, a distributed dynamic load balanced clustering (DDLBC algorithm is proposed. In this algorithm, each member in the cluster is to calculate the cooperative gain, residual energy, distance, and sensing cost from the neighboring clusters to perform the optimal decision. Each member in a cluster participates in selecting a cluster head (CH through cooperative gain, and residual energy that minimises network energy consumption and enhances the channel sensing. First, we form the number of clusters using the Markov decision process (MDP model to reduce the energy consumption in a network. In this algorithm, CR users effectively utilize the PUs reporting time slots of unavailability. The simulation results reveal that the clusters convergence, energy efficiency, and accuracy of channel sensing increased considerably by using the proposed algorithm.

Energy Efficient Cooperative Spectrum Sensing in Cognitive Radio Networks Using Distributed Dynamic Load Balanced Clustering Scheme

Directory of Open Access Journals (Sweden)

Muthukkumar R.

2016-07-01

Full Text Available Cognitive Radio (CR is a promising and potential technique to enable secondary users (SUs or unlicenced users to exploit the unused spectrum resources effectively possessed by primary users (PUs or licenced users. The proven clustering approach is used to organize nodes in the network into the logical groups to attain energy efficiency, network scalability, and stability for improving the sensing accuracy in CR through cooperative spectrum sensing (CSS. In this paper, a distributed dynamic load balanced clustering (DDLBC algorithm is proposed. In this algorithm, each member in the cluster is to calculate the cooperative gain, residual energy, distance, and sensing cost from the neighboring clusters to perform the optimal decision. Each member in a cluster participates in selecting a cluster head (CH through cooperative gain, and residual energy that minimises network energy consumption and enhances the channel sensing. First, we form the number of clusters using the Markov decision process (MDP model to reduce the energy consumption in a network. In this algorithm, CR users effectively utilize the PUs reporting time slots of unavailability. The simulation results reveal that the clusters convergence, energy efficiency, and accuracy of channel sensing increased considerably by using the proposed algorithm.

Ternary fission of 184466,476X formed in U + U collisions

International Nuclear Information System (INIS)

Karthikraj, C.; Subramanian, S.; Selvaraj, S.

2016-01-01

Recently, the very rare process of nuclear ternary fission has been of great interest in nuclear dynamics. Based on the statistical theory of fission, we discuss here the ternary-fission mass distribution of 184 466,476 X formed in low-energy U + U collisions for different heavy third fragments at T = 1 and 2 MeV. The expected ternary configurations 208 Pb + 208 Pb + 50 Ca and 204 Hg + 204 Hg + 58 Cr are obtained from the ternary fission of 184 466 X at T = 2 MeV. In addition, for both the systems, various possible ternary modes are listed for different heavy third fragments. Our results clearly indicate that the favored ternary configurations have either proton and/or neutron shell closure nucleus as one of their partners. (orig.)

A high-throughput search for new ternary superalloys

Science.gov (United States)

Nyshadham, Chandramouli; Hansen, Jacob; Oses, Corey; Curtarolo, Stefano; Hart, Gus

In 2006 an unexpected new superalloy, Co3[Al,W], was discovered. This new alloy is cobalt-based, in contrast to conventional superalloys, which are nickel-based. Inspired by this new discovery, we performed first-principles calculations, searching through 2224 ternary metallic systems of the form A3[B0.5C0.5], where A = Ni/Co/Fe and [B, C] = all binary combinations of 40 different elements chosen from the periodic table. We found 175 new systems that are better than the Co3[Al, W] superalloy. 75 of these systems are brand new--they have never been reported in experimental literature. These 75 new potential superalloys are good candidates for further experiments. Our calculations are consistent with current experimental literature where data exists. Work supported under: ONR (MURI N00014-13-1-0635).

Energy-efficient power allocation of two-hop cooperative systems with imperfect channel estimation

KAUST Repository

Amin, Osama

2015-06-08

Recently, much attention has been paid to the green design of wireless communication systems using energy efficiency (EE) metrics that should capture all energy consumption sources to deliver the required data. In this paper, we formulate an accurate EE metric for cooperative two-hop systems that use the amplify-and-forward relaying scheme. Different from the existing research that assumes the availability of perfect channel state information (CSI) at the communication cooperative nodes, we assume a practical scenario, where training pilots are used to estimate the channels. The estimated CSI can be used to adapt the available resources of the proposed system in order to maximize the EE. Two estimation strategies are assumed namely disintegrated channel estimation, which assumes the availability of channel estimator at the relay, and cascaded channel estimation, where the relay is not equipped with channel estimator and only forwards the received pilot(s) in order to let the destination estimate the cooperative link. The channel estimation cost is reflected on the EE metric by including the estimation error in the signal-to-noise term and considering the energy consumption during the estimation phase. Based on the formulated EE metric, we propose an energy-aware power allocation algorithm to maximize the EE of the cooperative system with channel estimation. Furthermore, we study the impact of the estimation parameters on the optimized EE performance via simulation examples.

Improving Energy Efficiency of Cooperative Femtocell Networks via Base Station Switching Off

Directory of Open Access Journals (Sweden)

Woongsup Lee

2016-01-01

Full Text Available Recently, energy efficiency (EE of cellular networks has become an important performance metric, and several techniques have been proposed to increase the EE. Among them, turning off base stations (BSs when not needed is considered as one of the most powerful techniques due to its simple operation and effectiveness. Herein, we propose a novel BS switching-off technique for cooperative femtocell networks where multiple femtocell BSs (FBSs simultaneously send packets to the same mobile station (MS. Unlike conventional schemes, cooperative operation of FBSs, also known as coordinated multipoint (CoMP transmission, is considered to determine which BSs are turned off in the proposed technique. We first formulate the optimization problem to find the optimal set of FBSs to be turned off. Then, we propose a suboptimal scheme operating in a distributed manner in order to reduce the computational complexity of the optimal scheme. The suboptimal scheme is based on throughput ratio (TR which specifies the importance of a particular FBS for the cooperative transmission. Through simulations, we show that the energy consumption can be greatly reduced with the proposed technique, compared with conventional schemes. Moreover, we show that the suboptimal scheme also achieves the near-optimal performance even without the excessive computations.

Fusibility diagram of ternary system with incongruently melting double compound

International Nuclear Information System (INIS)

Lutsyk, V.I.; Vorob'eva, V.P.; Sumkina, O.G.

1989-01-01

Temperature calculation and properties of ternary eutectics and concentration coordinates of ternary peritectics accoriding to the linear model of initial crystallization surfaces as an element of the expert system for simulating fusibility diagrams of ternary systems is considered. It is shown that the calculated and experimental data on coordinates of ternary nonvariant points in the systems NaCl-PbCl 2 -CdCl 2 , PbCl 2 -CaCl 2 -UCl 4 , CaF 2 -NaF-CsF and UCl 3 -CaCl 2 -ThCl 4 are in good agreement

Crystallization features of ternary reversible reciprocal systems

International Nuclear Information System (INIS)

Tomashik, V.N.; Shcherbak, L.P.; Fejchuk, P.I.; Grytsiv, V.I.

2006-01-01

Some features of the primary crystallization of phases in ternary reversible reciprocal system are considered and discussed. The diagonal join CdTe-GeSe of the CdTe + GeSe = CdSe + GeTe ternary reciprocal system is studied to show that the features in primary and secondary heating and cooling curves in such systems under fully equilibrium conditions are not reproduced upon consecutive heating and cooling sessions, because of the existence of different amounts of the reagents and the reaction products in the mixture; the temperatures of each transformation lie in a range. Those who experimentally investigate other ternary and more complex reversible reciprocal systems should take this fact into account [ru

Ternary semitransparent organic solar cells with a laminated top electrode.

Science.gov (United States)

Makha, Mohammed; Testa, Paolo; Anantharaman, Surendra Babu; Heier, Jakob; Jenatsch, Sandra; Leclaire, Nicolas; Tisserant, Jean-Nicolas; Véron, Anna C; Wang, Lei; Nüesch, Frank; Hany, Roland

2017-01-01

Tinted and colour-neutral semitransparent organic photovoltaic elements are of interest for building-integrated applications in windows, on glass roofs or on facades. We demonstrate a semitransparent organic photovoltaic cell with a dry-laminated top electrode that achieves a uniform average visible transmittance of 51% and a power conversion efficiency of 3%. The photo-active material is based on a majority blend composed of a visibly absorbing donor polymer and a fullerene acceptor, to which a selective near-infrared absorbing cyanine dye is added as a minority component. Our results show that organic ternary blends are attractive for the fabrication of semitransparent solar cells in general, because a guest component with a complementary absorption can compensate for the inevitably reduced current generation capability of a high-performing binary blend when applied as a thin, semitransparent film.

Comparative analysis of the ternary complex factors Elk-1, SAP-1a and SAP-2 (ERP/NET).

Science.gov (United States)

Price, M A; Rogers, A E; Treisman, R

1995-06-01

A transcription factor ternary complex composed of Serum Response Factor (SRF) and Ternary Complex Factor (TCF) mediates the response of the c-fos Serum Response Element (SRE) to growth factors and mitogens. Three Ets domain proteins, Elk-1, SAP-1 and ERP/NET, have been reported to have the properties of TCF. Here we compare Elk-1 and SAP-1a with the human ERP/NET homologue SAP-2. All three TCF RNAs are ubiquitously expressed at similar relative levels. All three proteins contain conserved regions that interact with SRF and the c-fos SRE with comparable efficiency, but in vitro complex formation by SAP-2 is strongly inhibited by its C-terminal sequences. Similarly, only Elk-1 and SAP-1a efficiently bind the c-fos SRE in vivo; ternary complex formation by SAP-2 is weak and is substantially unaffected by serum stimulation or v-ras co-expression. All three TCFs contain C-terminal transcriptional activation domains that are phosphorylated following growth factor stimulation. Activation requires conserved S/T-P motifs found in all the TCF family members. Each TCF activation domain can be phosphorylated in vitro by partially purified ERK2, and ERK activation in vivo is sufficient to potentiate transcriptional activation.

A novel power efficient location-based cooperative routing with transmission power-upper-limit for wireless sensor networks.

Science.gov (United States)

Shi, Juanfei; Calveras, Anna; Cheng, Ye; Liu, Kai

2013-05-15

The extensive usage of wireless sensor networks (WSNs) has led to the development of many power- and energy-efficient routing protocols. Cooperative routing in WSNs can improve performance in these types of networks. In this paper we discuss the existing proposals and we propose a routing algorithm for wireless sensor networks called Power Efficient Location-based Cooperative Routing with Transmission Power-upper-limit (PELCR-TP). The algorithm is based on the principle of minimum link power and aims to take advantage of nodes cooperation to make the link work well in WSNs with a low transmission power. In the proposed scheme, with a determined transmission power upper limit, nodes find the most appropriate next nodes and single-relay nodes with the proposed algorithm. Moreover, this proposal subtly avoids non-working nodes, because we add a Bad nodes Avoidance Strategy (BAS). Simulation results show that the proposed algorithm with BAS can significantly improve the performance in reducing the overall link power, enhancing the transmission success rate and decreasing the retransmission rate.

A Novel Power Efficient Location-Based Cooperative Routing with Transmission Power-Upper-Limit for Wireless Sensor Networks

Science.gov (United States)

Shi, Juanfei; Calveras, Anna; Cheng, Ye; Liu, Kai

2013-01-01

The extensive usage of wireless sensor networks (WSNs) has led to the development of many power- and energy-efficient routing protocols. Cooperative routing in WSNs can improve performance in these types of networks. In this paper we discuss the existing proposals and we propose a routing algorithm for wireless sensor networks called Power Efficient Location-based Cooperative Routing with Transmission Power-upper-limit (PELCR-TP). The algorithm is based on the principle of minimum link power and aims to take advantage of nodes cooperation to make the link work well in WSNs with a low transmission power. In the proposed scheme, with a determined transmission power upper limit, nodes find the most appropriate next nodes and single-relay nodes with the proposed algorithm. Moreover, this proposal subtly avoids non-working nodes, because we add a Bad nodes Avoidance Strategy (BAS). Simulation results show that the proposed algorithm with BAS can significantly improve the performance in reducing the overall link power, enhancing the transmission success rate and decreasing the retransmission rate. PMID:23676625

High Strength Lightweight Concrete Made with Ternary Mixtures of Cement-Fly Ash-Silica Fume and Scoria as Aggregate

OpenAIRE

YAŞAR, Ergül; ATIŞ, Cengiz Duran; KILIÇ, Alaettin

2014-01-01

This paper presents part of the results of an ongoing laboratory study carried out to design a structural lightweight high strength concrete (SLWHSC) made with and without ternary mixtures of cement-fly ash-silica fume. In the mixtures, lightweight basaltic-pumice (scoria) aggregate was used. A concrete mixture made with lightweight scoria, and another lightweight scoria concrete mixture incorporating 20% fly ash and 10% silica fume as a cement replacement, were prepared. Two normal...

A ternary-complex of a suicide gene, a RAGE-binding peptide, and polyethylenimine as a gene delivery system with anti-tumor and anti-angiogenic dual effects in glioblastoma.

Science.gov (United States)

Choi, Eunji; Oh, Jungju; Lee, Dahee; Lee, Jaewon; Tan, Xiaonan; Kim, Minkyung; Kim, Gyeungyun; Piao, Chunxian; Lee, Minhyung

2018-04-13

The receptor for advanced glycation end-products (RAGE) is involved in tumor angiogenesis. Inhibition of RAGE might be an effective anti-angiogenic therapy for cancer. In this study, a cationic RAGE-binding peptide (RBP) was produced as an antagonist of RAGE, and a ternary-complex consisting of RBP, polyethylenimine (2 kDa, PEI2k), and a suicide gene (pHSVtk) was developed as a gene delivery system with dual functions: the anti-tumor effect of pHSVtk and anti-angiogenic effect of RBP. As an antagonist of RAGE, RBP decreased the secretion of vascular-endothelial growth factor (VEGF) in activated macrophages and reduced the tube-formation of endothelial cells in vitro. In in vitro transfection assays, the RBP/PEI2k/plasmid DNA (pDNA) ternary-complex had higher transfection efficiency than the PEI2k/pDNA binary-complex. In an intracranial glioblastoma animal model, the RBP/PEI2k/pHSVtk ternary-complex reduced α-smooth muscle actin expression, suggesting that the complex has an anti-angiogenic effect. In addition, the ternary-complex had higher pHSVtk delivery efficiency than the PEI2k/pHSVtk and PEI25k/pHSVtk binary-complexes in an animal model. As a result, the ternary-complex induced apoptosis and reduced tumor volume more effectively than the PEI2k/pHSVtk and PEI25k/pHSVtk binary-complexes. In conclusion, due to its dual anti-tumor and anti-angiogenesis effects, the RBP/PEI2k/pHSVtk ternary-complex might be an efficient gene delivery system for the treatment of glioblastoma. Copyright © 2018 Elsevier B.V. All rights reserved.

Ordering and site occupancy of ternary elements in Fe{sub 3}Al

Energy Technology Data Exchange (ETDEWEB)

Rademacher, Thomas; Al-Kassab, Talaat; Kirchheim, Reiner [Institut fuer Materialphysik, Universitaet Goettingen (Germany)

2009-07-01

Ordered iron aluminides exhibit a number of advantageous properties, such as high-temperature strength, corrosion resistance and low cost. Therefore, iron aluminum based alloys are considered to replace in some cases high alloyed ferritic stainless steels, especially DO{sub 3} - ordered Fe{sub 3}Al. The mechanical properties and high-temperature stability can be optimized when ternary elements are added. In this study the site occupancy of ternary elements (4at.%V, 5at.%Cr, 5at.%Mn) has been investigated by means of Atom Probe Tomography (APT). A special analysis algorithm allows resolving the atom layers for different measurement directions which enables determining site preferences. Additionally, comparing the succession of layers with simulations the binding energies of the participating elements can be estimated.

Globe report on energy in Central and Easter Europe and the CIS: An urgent need for international cooperation on energy efficiency improvement for sustainable development

International Nuclear Information System (INIS)

Laponche, B.; Baguenier, H.

1998-01-01

In comparison with European Union countries, the countries of Central and Eastern Europe as well as the Confederation of Independent States are characterized by a very high energy intensity i.e. ratio of energy consumption to gross domestic product. The paper deals with most important factors influencing this high energy intensity; variety of situations in different countries affecting the power supplies; an urgent need for energy efficiency policy and cooperation related to sustainable development; the necessary tools for energy efficiency implementation. Main energy data and global indicators are shown in the appendix

Hydrogen-bonding behavior of various conformations of the HNO3…(CH3OH)2 ternary system.

Science.gov (United States)

Özsoy, Hasan; Uras-Aytemiz, Nevin; Balcı, F Mine

2017-12-21

Nine minima were found on the intermolecular potential energy surface for the ternary system HNO 3 (CH 3 OH) 2 at the MP2/aug-cc-pVDZ level of theory. The cooperative effect, which is a measure of the hydrogen-bonding strength, was probed in these nine conformations of HNO 3 …(CH 3 OH) 2 . The results are discussed here in terms of structures, energetics, infrared vibrational frequencies, and topological parameters. The cooperative effect was observed to be an important contributor to the total interaction energies of the cyclic conformers of HNO 3 …(CH 3 OH) 2 , meaning that it cannot be neglected in simulations in which the pair-additive potential is applied. Graphical abstract The H-bonding behavior of various conformations of the HNO 3 (CH 3 OH) 2 trimer was investigated.

Intergrown SnO{sub 2}–TiO{sub 2}@graphene ternary composite as high-performance lithium-ion battery anodes

Energy Technology Data Exchange (ETDEWEB)

Jiao, Zheng; Gao, Renmei [Shanghai University, Institute of Nanochemistry and Nanobiology, School of Environmental and Chemical Engineering (China); Tao, Haihua [Inspection Center of Industrial Products and Raw Materials of SHCIQ (China); Yuan, Shuai [Shanghai University, Research Center of Nanoscience and Nanotechnology (China); Xu, Laiqiang; Xia, Saisai; Zhang, Haijiao, E-mail: hjzhang128@shu.edu.cn [Shanghai University, Institute of Nanochemistry and Nanobiology, School of Environmental and Chemical Engineering (China)

2016-10-15

In recent years, a lot of metal oxides with high theoretical capacity have widely investigated as the high-performance anode materials for lithium-ion batteries (LIBs). In this work, a simple, facile and effective one-pot hydrothermal strategy toward ternary SnO{sub 2}–TiO{sub 2}@graphene composite has been developed by using SnCl{sub 2} and TiOSO{sub 4} as the starting materials. The obtained composite demonstrates a unique structure and high surface areas, in which both SnO{sub 2} and TiO{sub 2} nanoparticles are well grown on the surface of graphene. More interestingly, the SnO{sub 2} and TiO{sub 2} nanoparticles are intergrowth together, totally different with the traditional ternary hybrids. When used as anode material for LIBs, the introduction of TiO{sub 2} plays a crucial role in maintaining the structural stability of the electrode during Li{sup +} insertion/extraction, which can effectively prevent the aggregation of SnO{sub 2} nanoparticles. The electrochemical tests indicate that as-prepared SnO{sub 2}–TiO{sub 2}@graphene composite exhibits a high capacity of 1276 mA h g{sup −1} after 200 cycles at the current density of 200 mA g{sup −1}. Furthermore, the composite also maintains the specific capacity of 611 mA h g{sup −1} at an ultrahigh current density of 2000 mA g{sup −1}, which is superior to those of the reported SnO{sub 2} and SnO{sub 2}/graphene hybrids. Accordingly, the remarkable electrochemical performance of ternary SnO{sub 2}–TiO{sub 2}@graphene composites is mainly attributed to their unique nanostructure, high surface areas, and the synergistic effect not only between graphene and metal oxides but also between the intergrown SnO{sub 2} and TiO{sub 2} nanoparticles.Graphical abstractIntergrown SnO{sub 2} and TiO{sub 2} nanoparticles have been successfully anchored onto the graphene nanosheets as high-performance lithium-ion battery anodes.

Neutron Damage and MAX Phase Ternary Compounds

Energy Technology Data Exchange (ETDEWEB)

Barsoum, Michael [Drexel Univ., Philadelphia, PA (United States); Hoffman, Elizabeth [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Sindelar, Robert [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Garcua-Duaz, Brenda [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Kohse, Gordon [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

2014-06-17

The Demands of Gen IV nuclear power plants for long service life under neutron radiation at high temperature are severe. Advanced materials that would withstand high temperatures (up to 1000+ C) to high doses in a neutron field would be ideal for reactor internal structures and would add to the long service life and reliability of the reactors. The objective of this work is to investigate the response of a new class of machinable, conductive, layered, ternary transition metal carbides and nitrides - the so-called MAX phases - to low and moderate neutron dose levels.

Neutron Damage and MAX Phase Ternary Compounds

International Nuclear Information System (INIS)

Barsoum, Michael; Hoffman, Elizabeth; Sindelar, Robert; Garcua-Diaz, Brenda; Kohse, Gordon

2014-01-01

The Demands of Gen IV nuclear power plants for long service life under neutron radiation at high temperature are severe. Advanced materials that would withstand high temperatures (up to 1000+ C) to high doses in a neutron field would be ideal for reactor internal structures and would add to the long service life and reliability of the reactors. The objective of this work is to investigate the response of a new class of machinable, conductive, layered, ternary transition metal carbides and nitrides - the so-called MAX phases - to low and moderate neutron dose levels.

Enhanced Light Absorption in Fluorinated Ternary Small-Molecule Photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Eastham, Nicholas D. [Department; Dudnik, Alexander S. [Department; Harutyunyan, Boris [Department; Aldrich, Thomas J. [Department; Leonardi, Matthew J. [Department; Manley, Eric F. [Department; Chemical; Butler, Melanie R. [Department; Harschneck, Tobias [Department; Ratner, Mark A. [Department; Chen, Lin X. [Department; Chemical; Bedzyk, Michael J. [Department; Department; Melkonyan, Ferdinand S. [Department; Facchetti, Antonio [Department; Chang, Robert P. H. [Department; Marks, Tobin J. [Department; Department

2017-06-14

Using small-molecule donor (SMD) semiconductors in organic photovoltaics (OPVs) has historically afforded lower power conversion efficiencies (PCEs) than their polymeric counterparts. The PCE difference is attributed to shorter conjugated backbones, resulting in reduced intermolecular interactions. Here, a new pair of SMDs is synthesized based on the diketopyrrolopyrrole-benzodithiophene-diketopyrrolopyrrole (BDT-DPP2) skeleton but having fluorinated and fluorinefree aromatic side-chain substituents. Ternary OPVs having varied ratios of the two SMDs with PC61BM as the acceptor exhibit tunable open-circuit voltages (Vocs) between 0.833 and 0.944 V due to a fluorination-induced shift in energy levels and the electronic “alloy” formed from the miscibility of the two SMDs. A 15% increase in PCE is observed at the optimal ternary SMD ratio, with the short-circuit current density (Jsc) significantly increased to 9.18 mA/cm2. The origin of Jsc enhancement is analyzed via charge generation, transport, and diffuse reflectance measurements, and is attributed to increased optical absorption arising from a maximum in film crystallinity at this SMD ratio, observed by grazing incidence wide-angle X-ray scattering.

Kinetic study of lithium-cadmium ternary amalgam decomposition

International Nuclear Information System (INIS)

Cordova, M.H.; Andrade, C.E.

1992-01-01

The effect of metals, which form stable lithium phase in binary alloys, on the formation of intermetallic species in ternary amalgams and their effect on thermal decomposition in contact with water is analyzed. Cd is selected as ternary metal, based on general experimental selection criteria. Cd (Hg) binary amalgams are prepared by direct contact Cd-Hg, whereas Li is formed by electrolysis of Li OH aq using a liquid Cd (Hg) cathodic well. The decomposition kinetic of Li C(Hg) in contact with 0.6 M Li OH is studied in function of ageing and temperature, and these results are compared with the binary amalgam Li (Hg) decomposition. The decomposition rate is constant during one hour for binary and ternary systems. Ageing does not affect the binary systems but increases the decomposition activation energy of ternary systems. A reaction mechanism that considers an intermetallic specie participating in the activated complex is proposed and a kinetic law is suggested. (author)

Calculation of Fe–B–V ternary phase diagram

International Nuclear Information System (INIS)

Homolová, Viera; Kroupa, Aleš; Výrostková, Anna

2012-01-01

Highlights: ► Phase diagram of Fe–B–V system was modelled by CALPHAD method. ► Database for thermodynamic calculations for Fe–B–V system was created. ► The new ternary phase was found in 67Fe–18B–15V [in at.%] alloy. - Abstract: The phase equilibria of the Fe–B–V ternary system are studied experimentally and theoretically in this paper. Phase diagram of the system was modelled by CALPHAD method. Boron was modelled as an interstitial element in the FCC and BCC solid solutions. The calculations of isothermal sections of phase diagram are compared with our experimental results at 903 and 1353 K and with available literature experimental data. New ternary phase (with chemical composition 28Fe32V40B in at.%) was found in 67Fe–18B–15V alloy [in at.%]. Further experimental studies for the determination of exact nature of the ternary phase including crystallographic information are necessary.

Low-temperature solid-state preparation of ternary CdS/g-C_3N_4/CuS nanocomposites for enhanced visible-light photocatalytic H_2-production activity

International Nuclear Information System (INIS)

Cheng, Feiyue; Yin, Hui; Xiang, Quanjun

2017-01-01

Highlights: • CdS/g-C_3N_4/CuS composite were synthesized by low-temperature solid-state method. • CdS/g-C_3N_4/CuS show enhanced visible-light photocatalytic H_2 evolution activity. • The enhanced photocatalytic H_2 production activity is due to the heterojunction. • Heterojunction between the components promote charge separation/transfer property. - Abstract: Low-temperature solid-state method were gradually demonstrated as a high efficiency, energy saving and environmental protection strategy to fabricate composite semiconductor materials. CdS-based multiple composite photocatalytic materials have attracted increasing concern owning to the heterostructure constituents with tunable band gaps. In this study, the ternary CdS/g-C_3N_4/CuS composite photocatalysts were prepared by a facile and novel low-temperature solid-state strategy. The optimal ternary CdS/g-C_3N_4/CuS composite exhibits a high visible-light photocatalytic H_2-production rate of 57.56 μmol h"−"1 with the corresponding apparent quantum efficiency reaches 16.5% at 420 nm with Na_2S/Na_2SO_3 mixed aqueous solution as sacrificial agent. The ternary CdS/g-C_3N_4/CuS composites show the enhanced visible-light photocatalytic H_2-evolution activity comparing with the binary CdS-based composites or simplex CdS. The enhanced photocatalytic activity is ascribed to the heterojunctions and the synergistic effect of CuS and g-C_3N_4 in promotion of the charge separation and charge mobility. This work shows that the low-temperature solid-state method is efficient and environmentally benign for the preparation of CdS-based multiple composite photocatalytic materials with enhanced visible-light photocatalytic H_2-production activity.

The role of In in III-nitride ternary semiconductors

CERN Multimedia

Redondo cubero, A

This proposal aims to study the role of In in the outstanding efficiency of luminescent devices based on group III-nitride ternary semiconductors. To study the microscopic environments of In in GaInN and AlInN, Perturbed Angular Correlation (PAC) experiments will be performed using the PAC-probes $^{111m}$Cd($^{111}$Cd), $^{115}$Cd($^{115}$In) and $^{117}$Cd($^{117}$In). Temperature dependent PAC measurements using the $^{111}$In($^{111}$Cd) probe indicated that In in GaN and AlN forms a complex with a defect, possibly a nitrogen vacancy (V$_{N}$), which is stable up to high temperatures and might be involved in the luminescence mechanisms. Analysing these results two questions arose: \\\\ \\\\1. Does the fact that the actual measurement is performed with the daughter nucleus $^{111}$Cd (being an acceptor) influence the probe-defect interaction? This question can be answered by performing measurements with the complementary probe $^{117}$Cd($^{117}$In). \\\\ \\\\ 2. What is the significance of $\\textit{a...

Control mechanism of double-rotator-structure ternary optical computer

Science.gov (United States)

Kai, SONG; Liping, YAN

2017-03-01

Double-rotator-structure ternary optical processor (DRSTOP) has two characteristics, namely, giant data-bits parallel computing and reconfigurable processor, which can handle thousands of data bits in parallel, and can run much faster than computers and other optical computer systems so far. In order to put DRSTOP into practical application, this paper established a series of methods, namely, task classification method, data-bits allocation method, control information generation method, control information formatting and sending method, and decoded results obtaining method and so on. These methods form the control mechanism of DRSTOP. This control mechanism makes DRSTOP become an automated computing platform. Compared with the traditional calculation tools, DRSTOP computing platform can ease the contradiction between high energy consumption and big data computing due to greatly reducing the cost of communications and I/O. Finally, the paper designed a set of experiments for DRSTOP control mechanism to verify its feasibility and correctness. Experimental results showed that the control mechanism is correct, feasible and efficient.

Solution processed ternary blend nano-composite charge regulation layer to enhance inverted OLED performances

Science.gov (United States)

Kaçar, Rifat; Mucur, Selin Pıravadılı; Yıldız, Fikret; Dabak, Salih; Tekin, Emine

2018-04-01

Inverted bottom-emission organic light emitting diodes (IBOLEDs) have attracted increasing attention due to their exceptional air stability and applications in active-matrix displays. For gaining high IBOLED device efficiencies, it is crucial to develop an effective strategy to make the bottom electrode easy for charge injection and transport. Charge selectivity, blocking the carrier flow towards the unfavourable side, plays an important role in determining charge carrier balance and accordingly radiative recombination efficiency. It is therefore highly desirable to functionalize an interfacial layer which will perform many different tasks simultaneously. Here, we contribute to the hole-blocking ability of the zinc oxide/polyethyleneimine (ZnO:PEI) nano-composite (NC) interlayer with the intention of increasing the OLED device efficiency. With this purpose in mind, a small amount of 1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBi) was added as a hole-blocking molecule into the binary blend of ZnO and PEI solution. The device with a ternary ZnO:PEI:TPBi NC interlayer achieved a maximum current efficiency of 38.20 cd A-1 and a power efficiency of 34.29 lm W-1 with a luminance of 123 200 cd m-2, which are high performance parameters for inverted device architecture. The direct comparisons of device performances incorporating ZnO only, ZnO/PEI bilayers, and ZnO:PEI binary NC counterparts were also performed, which shed light on the origin of device performance enhancement.

Asymmetric supercapacitors with metal-like ternary selenides and porous graphene electrodes

KAUST Repository

Xia, Chuan

2016-04-14

Asymmetric supercapacitors provide a promising approach to fabricate capacitive energy storage devices with high energy and power densities. In this work, asymmetric supercapacitors with excellent performance have been fabricated using ternary (Ni, Co)0.85Se on carbon fabric as bind-free positive electrode and porous free-standing graphene films as negative electrode. Owing to their metal-like conductivity (~1.67×106 S m−1), significant electrochemical activity, and superhydrophilic nature, our nanostructured ternary nickel cobalt selenides result in a much higher areal capacitance (2.33 F cm−2 at 4 mA cm−2), better rate performance and cycling stability than their binary selenide equivalents, and other ternary oxides and chalcogenides. Those hybrid supercapacitors can afford impressive areal capacitance and stack capacitance of 529.3 mF cm−2 and 6330 mF cm−3 at 1 mA cm−2, respectively. More impressively, our optimized asymmetric device operating at 1.8 V delivers a very high stack energy density of 2.85 mWh cm−3 at a stack power density of 10.76 mW cm−3, as well as 85% capacitance retention after 10,000 continuous charge-discharge cycles. Even at a high stack power density of 1173 mW cm−3, this device still deliveries a stack energy density of 1.19 mWh cm−3, superior to most of the reported supercapacitors.

Experimental investigation of phase equilibria in the Co-W-V ternary system

International Nuclear Information System (INIS)

Liu Xingjun; Zhu Yihong; Yu Yan; Wang Cuiping

2011-01-01

Highlights: → Three isothermal sections of the Co-W-V ternary system at 1100 deg. C, 1200 deg. C and 1300 deg. C were determined. → No ternary compound was found in the Co-W-V ternary system. → A stable liquid miscibility gap is newly discovered in the Co-W-V ternary system. → This work is of great essence to establish the thermodynamic database for the Co-based alloys. - Abstract: The phase equilibria in the Co-W-V ternary system were experimentally investigated by optical microscopy (OM), electron probe microanalysis (EPMA) and X-ray diffraction (XRD) on the equilibrated alloys. Three isothermal sections of the Co-W-V ternary system at 1100 deg. C, 1200 deg. C and 1300 deg. C were determined, and no ternary compound was found in this system. In addition, a novel phenomena induced by the liquid phase separation in the Co-W-V alloys was firstly discovered, suggesting that a stable liquid miscibility gap exists in the Co-W-V ternary system. The newly determined phase equilibria and firstly discovered phase separation phenomena in the Co-W-V system will provide important information for the development of Co-W based alloys.

The durability of concrete containing a high-level of fly ash or a ternary blend of supplementary cementing materials

Science.gov (United States)

Gilbert, Christine M.

The research for this study was conducted in two distinct phases as follows: Phase 1: The objective was to determine the effect of fly ash on the carbonation of concrete. The specimens made for this phase of the study were larger in size than those normally used in carbonation studies and were are meant to more accurately reflect real field conditions. The results from early age carbonation testing indicate that the larger size specimens do not have a measured depth of carbonation as great as that of the smaller specimens typically used in carbonation studies at the same age and under the same conditions. Phase 2: The objective was to evaluate the performance of ternary concrete mixes containing a ternary cement blend consisting of Portland cement, slag and Type C fly ash. It was found that concrete mixtures containing the fly ash with the lower calcium (CaO) content (in binary or ternary blends) provided superior durability performance and resistance to ASR compared to that of the fly ash with the higher CaO content. Ternary blends (regardless of the CaO content of the fly ash) provided better overall durability performance than binary blends of cementing materials or the control.

Synthesis and characterization of highly efficient and stable Pr6O11/Ag3PO4/Pt ternary hybrid structure

International Nuclear Information System (INIS)

Deng, Jiatao; Liu, Lin; Niu, Tongjun; Sun, Xiaosong

2017-01-01

Highlights: • Visible-light-driven Pr 6 O 11 /Ag 3 PO 4 /Pt photocatalysts were prepared. • Pr 6 O 11 /Ag 3 PO 4 /Pt showed highly efficient and stable photocatalystic activity. • The photocatalytic mechanism of Pr 6 O 11 /Ag 3 PO 4 /Pt composite was given. - Abstract: Ag 3 PO 4 is an excellent photocatalyst with high efficiency and quantum yield, but suffers from the fast recombination of photogenerated electron-hole pairs and photo-corrosion. Hereby, the highly efficient and stable visible-light-driven Pr 6 O 11 /Ag 3 PO 4 /Pt photocatalyst were prepared via a three-step wet chemical approach. The as-prepared Pr 6 O 11 /Ag 3 PO 4 /Pt composite was characterized by X-ray diffraction, US-vis diffuse reflectance spectroscopy, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, photoluminescence spectra and transient photocurrent as well. Comparing with single Pr 6 O 11 or Ag 3 PO 4 , the prepared Pr 6 O 11 /Ag 3 PO 4 /Pt composite exhibited much higher photocatalytic activity and stability for the degradation of Rhodamine B under visible light irradiation (>420 nm). The enhanced photocatalytic performance of Pr 6 O 11 /Ag 3 PO 4 /Pt composite has been attributed to the efficient separation of photo-generated electron-hole pairs through a scheme system composed of Pr 6 O 11, Ag 3 PO 4 and Pt.

Effect of ternary alloying elements on microstructure and mechanical property of Nb-Si based refractory intermetallic alloy

International Nuclear Information System (INIS)

Kim, W.Y.; Kim, H.S.; Kim, S.K.; Ra, T.Y.; Kim, M.S.

2005-01-01

Microstructure and mechanical property at room temperature and at 1773 K of Nb-Si based refractory intermetallic alloys were investigated in terms of compression and fracture toughness test. Mo and V were chosen as ternary alloying elements because of their high melting points, atomic sizes smaller than Nb. Both ternary alloying elements were found to have a significant role in modifying the microstructure from dispersed structure to eutectic-like structure in Nb solid solution/Nb 5 Si 3 intermetallic composites. The 0.2% offset yield strength at room temperature increased with increasing content of ternary elements in Nb solid solution and volume fraction of Nb 5 Si 3 . At 1773 K, Mo addition has a positive role in increasing the yield strength. On the other hand, V addition has a role in decreasing the yield strength. The fracture toughness of ternary alloys was superior to binary alloys. Details will be discussed in correlation with ternary alloying, volume fraction of constituent phase, and the microstructure. (orig.)

Preparation of reduced graphene oxide/meso-TiO{sub 2}/AuNPs ternary composites and their visible-light-induced photocatalytic degradation n of methylene blue

Energy Technology Data Exchange (ETDEWEB)

Yang, Yongfang; Ma, Zheng; Xu, Lidong [School of Chemical Engineering and Technology, Hebei University of Technology, Tianjin 300130 (China); Wang, Hefang, E-mail: whf0618@163.com [School of Chemical Engineering and Technology, Hebei University of Technology, Tianjin 300130 (China); Fu, Nian, E-mail: funian3678@163.com [School of Chemical Engineering and Technology, Hebei University of Technology, Tianjin 300130 (China); College of Physics Science and Technology of Hebei University, Baoding 071002 (China)

2016-04-30

Graphical abstract: Reduced graphene oxide/meso-TiO{sub 2}/AuNPs (RGO/meso-TiO{sub 2}/AuNPs) ternary composites were prepared via the addition of graphene oxide to the dispersion of meso-TiO{sub 2}/AuNPs under a hydrothermal condition. The RGO/meso-TiO{sub 2}/AuNPs ternary composites show high photocatalytic activity toward MB. - Highlights: • RGO/meso-TiO{sub 2}/AuNPs were obtained by addition of graphene oxide to meso-TiO{sub 2}/AuNPs. • Au NPs in the mesopores of meso-TiO{sub 2} reduce the recombination of charge carriers. • RGO covered with the surface of the meso-TiO{sub 2} enhance the adsorption of MB. • RGO/meso-TiO{sub 2}/AuNPs composites show high photocatalytic performance toward MB. - Abstract: Reduced graphene oxide/meso-TiO{sub 2}/AuNPs (RGO/meso-TiO{sub 2}/AuNPs) ternary composites were prepared via the addition of graphene oxide to the dispersion of meso-TiO{sub 2}/AuNPs under hydrothermal conditions. The structure and the morphology of the RGO/meso-TiO{sub 2}/AuNPs materials were characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The photocatalytic activity of RGO/meso-TiO{sub 2}/AuNPs was evaluated by degradation of methyl blue (MB) under visible-light illumination. The ternary composites present an extended light absorption range, efficient charge separation properties, high adsorption ability for MB and high photocatalytic degradation activity of MB compared to the meso-TiO{sub 2} and meso-TiO{sub 2}/AuNPs.

Sequential character of low-energy ternary and quaternary nuclear fission

Energy Technology Data Exchange (ETDEWEB)

Kadmensky, S. G., E-mail: kadmensky@phys.vsu.ru; Bulychev, A. O. [Voronezh State University (Russian Federation)

2016-09-15

An analysis of low-energy true ternary (quaternary) nuclear fission leads to the conclusion that these fission modes have a sequential two-step (three-step) character such that the emission of a third particle (third and fourth particles) and the separation of fission fragments occur at distinctly different instants, in contrast to the simultaneous emergence of all fission products in the case of onestep ternary (quaternary) fission. This conclusion relies on the following arguments. First, the emission of a third particle (third and fourth particles) from a fissile nucleus is due to a nonevaporative mechanism associated with a nonadiabatic character of the collective deformation motion of this nucleus at the stages preceding its scission. Second, the axial symmetry of the deformed fissile compound nucleus and the direction of its symmetry axis both remain unchanged at all stages of ternary (quaternary) fission. This circumstancemakes it possible to explain themechanism of the appearance of observed anisotropies and T — odd asymmeries in the angular distributions of products of ternary (quaternary) nuclear fission. Third, the T —odd asymmetry discovered experimentally in ternary nuclear fission induced by cold polarized neutrons obeys the T —invariance condition only in the case of a sequential two-step (three-step) character of true ternary (quaternary) nuclear fission. At the same time, this asymmetry is not a T —invariant quantity in the case of the simultaneous emission of products of true ternary (quaternary) nuclear fission from the fissile compound nucleus.

Sequential character of low-energy ternary and quaternary nuclear fission

International Nuclear Information System (INIS)

Kadmensky, S. G.; Bulychev, A. O.

2016-01-01

An analysis of low-energy true ternary (quaternary) nuclear fission leads to the conclusion that these fission modes have a sequential two-step (three-step) character such that the emission of a third particle (third and fourth particles) and the separation of fission fragments occur at distinctly different instants, in contrast to the simultaneous emergence of all fission products in the case of onestep ternary (quaternary) fission. This conclusion relies on the following arguments. First, the emission of a third particle (third and fourth particles) from a fissile nucleus is due to a nonevaporative mechanism associated with a nonadiabatic character of the collective deformation motion of this nucleus at the stages preceding its scission. Second, the axial symmetry of the deformed fissile compound nucleus and the direction of its symmetry axis both remain unchanged at all stages of ternary (quaternary) fission. This circumstancemakes it possible to explain themechanism of the appearance of observed anisotropies and T — odd asymmeries in the angular distributions of products of ternary (quaternary) nuclear fission. Third, the T —odd asymmetry discovered experimentally in ternary nuclear fission induced by cold polarized neutrons obeys the T —invariance condition only in the case of a sequential two-step (three-step) character of true ternary (quaternary) nuclear fission. At the same time, this asymmetry is not a T —invariant quantity in the case of the simultaneous emission of products of true ternary (quaternary) nuclear fission from the fissile compound nucleus.

Splitting efficiency and interference effects in a Cooper pair splitter based on a triple quantum dot with ferromagnetic contacts

Science.gov (United States)

Bocian, Kacper; Rudziński, Wojciech; Weymann, Ireneusz

2018-05-01

We theoretically study the spin-resolved subgap transport properties of a Cooper pair splitter based on a triple quantum dot attached to superconducting and ferromagnetic leads. Using the Keldysh Green's function formalism, we analyze the dependence of the Andreev conductance, Cooper pair splitting efficiency, and tunnel magnetoresistance on the gate and bias voltages applied to the system. We show that the system's transport properties are strongly affected by spin dependence of tunneling processes and quantum interference between different local and nonlocal Andreev reflections. We also study the effects of finite hopping between the side quantum dots on the Andreev current. This allows for identifying the optimal conditions for enhancing the Cooper pair splitting efficiency of the device. We find that the splitting efficiency exhibits a nonmonotonic dependence on the degree of spin polarization of the leads and the magnitude and type of hopping between the dots. An almost perfect splitting efficiency is predicted in the nonlinear response regime when the energies of the side quantum dots are tuned to the energies of the corresponding Andreev bound states. In addition, we analyzed features of the tunnel magnetoresistance (TMR) for a wide range of the gate and bias voltages, as well as for different model parameters, finding the corresponding sign changes of the TMR in certain transport regimes. The mechanisms leading to these effects are thoroughly discussed.

Regional cooperation in energy efficiency standard-setting and labeling in North America

Energy Technology Data Exchange (ETDEWEB)

Wiel, Stephen; Van Wie McGrory, Laura

2003-08-04

The North American Energy Working Group (NAEWG) was established in 2001 by the governments of Canada, Mexico, and the United States. The goals of NAEWG are to foster communication and cooperation on energy-related matters of common interest, and to enhance North American energy trade and interconnections consistent with the goal of sustainable development, for the benefit of all three countries. At its outset, NAEWG established teams to address different aspects of the energy sector. One, the Energy Efficiency Expert Group, undertook activity in three areas: (1) analyzing commonalities and differences in the test procedures of Canada, Mexico, and the United States, and identifying specific products for which the three countries might consider harmonization; (2) exploring possibilities for increased mutual recognition of laboratory test results; and (3) looking at possibilities for enhanced cooperation in the Energy Star voluntary endorsement labeling program. To support NAEWG's Expert Group on Energy Efficiency (NAEWG-EE), USDOE commissioned Lawrence Berkeley National Laboratory, representing the Collaborative Labeling and Appliance Standards Program (CLASP), to prepare a resource document comparing current standards, labels, and test procedure regulations in Canada, Mexico, and the United States. The resulting document identified 46 energy-using products for which at least one of the three countries has energy efficiency regulations. Three products--refrigerators/freezers, room air conditioners, and integral horsepower three-phase electric motors--have identical minimum energy performance standards (MEPS) and test procedures in the three countries. Ten other products have different MEPS and test procedures, but have the near-term potential for harmonization. NAEWG-EE is currently working to identify mechanisms for mutual recognition of test results. With consultative support from the United States and Canada through NAEWG-EE, Mexico is exploring possibilities

Constitution of the ternary system Cr–Ni–Ti

International Nuclear Information System (INIS)

Krendelsberger, Natalja; Weitzer, Franz; Du, Yong; Schuster, Julius C.

2013-01-01

Highlights: •Reaction scheme and liquidus surface for Cr-Ni-Ti are given. •In the ternary the C14-type Laves phase coexists with the liquid phase. •Two ternary eutectics are identified. -- Abstract: The nature of solid–liquid phase equilibria in the ternary system Cr–Ni–Ti was investigated using electron microscopy, energy dispersive spectroscopy, X-ray diffraction, and differential thermal analysis. Literature data on solid state phase equilibria are confirmed. The Cr 2 Ti Laves phase modifications coexisting with Ni–Ti phases are clarified to be hexagonal C14-type and cubic C15-type. The C14-type Laves phase γCr 2 Ti is found to coexist with the liquid phase. It forms in the pseudobinary peritectic reaction p max1 from L + β(Cr,Ti) at 1389 °C. On further cooling γCr 2 Ti + NiTi solidify at 1202 °C in the pseudobinary eutectic e max2 . In the Cr-rich part of the system ternary eutectics occur at 1216 °C (E 1 : L = Ni 3 Ti + (Ni) + β(Cr,Ti)) and 1100 °C (E 2 : L = NiTi + Ni 3 Ti + β(Cr,Ti)), respectively. No ternary eutectic is found in the Ti-rich part. Rather the eutectic trough ends in the binary eutectic L = NiTi 2 + β(Ti)

Milk marketing under cooperative and non-cooperative marketing channels: Evidence from west Bengal

Directory of Open Access Journals (Sweden)

Sarker Debnarayan

2010-01-01

Full Text Available The present study is an attempt to empirically investigate the price spread, marketing costs, marketing margins, marketing efficiency, and profit efficiency among market middlemen under cooperative and non-cooperative marketing channels in the domestic trade market of liquid milk in West Bengal. One of the important findings of this study is that, although the inter-market (and intramarket price variation for liquid milk under the cooperative marketing agency in not far from uniformity, and all marketing agencies under cooperative channels receive much lower abnormal profit per unit of milk as compared with non-cooperative channels, the former fails to provide much economic benefit, either to the producer or to the consumer, because of the burden of much higher fixed cost per unit of liquid milk.

Efficiency Assessment of Economic International Cooperation in Development of Arctic Offshore Oil and Gas Resources

Directory of Open Access Journals (Sweden)

Polina V. Beresneva

2015-01-01

Full Text Available The research is focused on efficiency assessment of economic cooperation in development of Arctic offshore oil and gas resources. The author developed an economic model based on cost-benefit analysis (CBA. CBA is used in some countries (EU, USA, Australia as an analytic tool to make public policy decisions. CBA is based on the method of discounting cash flows associated with costs and benefits of public policy. It is assumed that all public goals are equally important inter alia, hence public bodies should opt for those initiatives that maximize public benefits for every dollar spent from the state budget. There are five stages of economic modeling: 1 the definition of public benefits and costs associated with the public initiative; 2 monetary valuation of costs and benefits; 3 the definition of discounting period and discounting rate; 4 the calculation of net present value of cash flows; 5 the comparison of initiatives' net present values. The model is built with a number of hypotheses assumed. It allows making evaluation of investments into the technology to decrease the cost of Arctic offshore oil and gas development. Moreover, the model has two scenarios describing a public policy to support technology development with international economic cooperation and without it. Under given hypotheses both scenarios return positive net present value of policies which proves that governmental initiative to support Arctic technology development is economically justified. Also the model sows that the scenario with international cooperation is more efficient from economic point of view. It is explained by two factors: the higher speed of technology transfer (due W international cooperation and the opportunity to use financial leverage (attracting the funds from foreign partners. The model allows closing the existing scientific gap between the theory of CBA method and its practical use in public decision making.

Zr-Fe-Sn Ternary System Phase Diagrams- New Experimental Results

International Nuclear Information System (INIS)

Nieva, N; Gomez, A; Arias, D

2004-01-01

New experimental results for the Zr-Fe-Sn ternary system are presented in this paper. The phases present and equilibrium relations for the 900 o C isothermal on the central zone of the Gibbs triangle are analysed. A set of ternary alloys was designed and obtained, and they were analysed by semi quantitative SEM- EDS, XRD, and metallographic samples. The resulting ternary phase diagrams are presented here (JCH)

Cooperative ad hoc networks for energy and delay efficient content distribution with fast channel variations

KAUST Repository

Atat, Rachad

2012-11-20

Cooperative ad hoc networks for the efficient distribution of content of common interest are studied in the case of fast channel variations. Mobiles are grouped into cooperative clusters for the purpose of receiving the content with optimized energy efficiency. Data are sent to mobile terminals on a long range (LR) link, and then, the terminals exchange the content by using an appropriate short range wireless technology. When channel state information is available for the LR links, unicasting is used on the LR. When accurate channel state information is not available, threshold-based multicasting is implemented on the LR. Energy minimization is formulated as an optimization problem for each scenario, and the optimal solutions are determined in closed form in scenarios with fast channel variations. Results show significant energy savings in the proposed schemes compared with the noncooperative case and other previous related work. Furthermore, the energy minimizing solutions are shown to lead to reduced delay in the content distribution process. Practical implementation aspects of the proposed methods are also discussed. © 2012 John Wiley & Sons, Ltd.

Cooperative ad hoc networks for energy and delay efficient content distribution with fast channel variations

KAUST Repository

Atat, Rachad; Yaacoub, Elias E.; Alouini, Mohamed-Slim; Abu-Dayya, Adnan A.

2012-01-01

Cooperative ad hoc networks for the efficient distribution of content of common interest are studied in the case of fast channel variations. Mobiles are grouped into cooperative clusters for the purpose of receiving the content with optimized energy efficiency. Data are sent to mobile terminals on a long range (LR) link, and then, the terminals exchange the content by using an appropriate short range wireless technology. When channel state information is available for the LR links, unicasting is used on the LR. When accurate channel state information is not available, threshold-based multicasting is implemented on the LR. Energy minimization is formulated as an optimization problem for each scenario, and the optimal solutions are determined in closed form in scenarios with fast channel variations. Results show significant energy savings in the proposed schemes compared with the noncooperative case and other previous related work. Furthermore, the energy minimizing solutions are shown to lead to reduced delay in the content distribution process. Practical implementation aspects of the proposed methods are also discussed. © 2012 John Wiley & Sons, Ltd.

A Three-dimensional Topological Model of Ternary Phase Diagram

International Nuclear Information System (INIS)

Mu, Yingxue; Bao, Hong

2017-01-01

In order to obtain a visualization of the complex internal structure of ternary phase diagram, the paper realized a three-dimensional topology model of ternary phase diagram with the designed data structure and improved algorithm, under the guidance of relevant theories of computer graphics. The purpose of the model is mainly to analyze the relationship between each phase region of a ternary phase diagram. The model not only obtain isothermal section graph at any temperature, but also extract a particular phase region in which users are interested. (paper)

Efficiency of the heat pump cooperating with various heat sources in monovalent and bivalent systems

Energy Technology Data Exchange (ETDEWEB)

Kurpaska, S.; Latala, H. [Krakow Univ. of Agriculture, Krakow (Poland). Inst. of Agricultural Engineering and Computer Science

2010-07-01

This paper reported on a study that tested the efficiency of compressor heat pumps cooperating with various types of lower heat sources such as horizontal ground heat exchangers, vertical exchangers and sources operating in the bivalent system. The system for receiving energy consisted of a traditional heating system and liquid-air exchangers. The study identified a strong relationship between the heating efficiency of the analysed systems and temperature inside the structure. The study showed that the bivalent system was fully capable of meeting a heat requirement of about 1 MJ -2.

Energy-Efficient Cooperative Techniques for Infrastructure-to-Vehicle Communications

OpenAIRE

Nguyen , Tuan-Duc; Berder , Olivier; Sentieys , Olivier

2011-01-01

International audience; In wireless distributed networks, cooperative relay and cooperative Multi-Input Multi-Output (MIMO) techniques can be used to exploit the spatial and temporal diversity gain in order to increase the performance or reduce the transmission energy consumption. The energy efficiency of cooperative MIMO and relay techniques is then very useful for the Infrastructure to Vehicle (I2V) and Infrastructure to Infrastructure (I2I) communications in Intelligent Transport Systems (I...

Charge distribution in the ternary fragmentation of {sup 252}Cf

Energy Technology Data Exchange (ETDEWEB)

Senthil Kannan, M.T.; Balasubramaniam, M. [Bharathiar University, Department of Physics, Coimbatore (India)

2017-08-15

We present here, for the first time, a study on ternary fragmentation charge distribution of {sup 252}Cf using the convolution integral method and the statistical theory. The charge distribution for all possible charge combinations of a ternary breakup are grouped as a bin containing different mass partitions. Different bins corresponding to various third fragments with mass numbers from A{sub 3} = 16 to 84 are identified with the available experimental masses. The corresponding potential energy surfaces are calculated using the three cluster model for the two arrangements A{sub 1} + A{sub 2} + A{sub 3} and A{sub 1} + A{sub 3} + A{sub 2}. The ternary fragmentation yield values are calculated for the ternary combination from each bin possessing minimum potential energy. The yields of the resulting ternary combinations as a function of the charge numbers of the three fragments are analyzed for both the arrangements. The calculations are carried out at different excitation energies of the parent nucleus. For each excitation energy the temperature of the three fragments are iteratively computed conserving the total energy. The distribution of fragment temperatures corresponding to different excitation energies for some fixed third fragments are discussed. The presence of the closed shell nucleus Sn in the favourable ternary fragmentation is highlighted. (orig.)

Study on the solid state chemistry of ternary uranium oxides

International Nuclear Information System (INIS)

Yamashita, Toshiyuki

1988-03-01

With the increase of burnup of uranium oxide fuels, various kinds of fission products are formed, and the oxygen atoms combined with the consumed heavy atoms are freed. The solid state chemical and/or thermodynamic properties of these elements at high temperatures are complex, and have not been well clarified. In the present report, an approach was taken that the chemical interactions between UO 2 and these fission products can be regarded as causing overlapped effects of composing ternary uranium oxides, and formation reactions and phase behavior were studied for several ternary uranium oxides with typical fission product elements such as alkaline earth metals and rare earth elements. Precise determination methods for the composition of ternary uranium oxides were developed. The estimated accuracies for x and y values in M y U 1-y O 2+x were ± 0.006 and ± 0.004, respectively. The thermodynamic properties and the lattice parameters of the phases in the Ca-U-O and Pr-U-O systems were discussed in relation to the composition determined by the methods. Crystal structure analyses of cadmium monouranates were made with X-ray diffraction method. (author) 197 refs

Density-Driven segregation in Binary and Ternary Granular Systems

NARCIS (Netherlands)

Windows-Yule, Kit; Parker, David

2015-01-01

We present a first experimental study of density-induced segregation within a three-dimensional, vibrofluidised, ternary granular system. Using Positron Emission Particle Tracking (PEPT), we study the steady-state particle distributions achieved by binary and ternary granular beds under a variety of

Ternary equilibria in bismuth--indium--lead alloys

International Nuclear Information System (INIS)

Liao, K.C.; Johnson, D.L.; Nelson, R.C.

1975-01-01

The liquidus surface is characterized by three binary equilibria. One binary extends from the Pb--Bi peritectic to the Pb--In peritectic. The other two extend from In--Bi eutectics, merge at 50 at. percent Bi and 30 at. percent Pb, and end at the Bi--Pb eutectic. Based on analysis of ternary liquidus contours and vertical sections, it is suggested that solidification for high lead and very high indium alloys occurs from two-phase equilibria. Solidification from all other alloys occurs from three-phase equilibria. Four-phase solidification does not occur in this system

Design and analysis of 2T-2M Ternary content addressable memories

KAUST Repository

Bahloul, M. A.; Fouda, M. E.; Naous, Rawan; Zidan, Mohammed A.; Eltawil, A. M.; Kurdahi, F.; Salama, Khaled N.

2017-01-01

Associate and approximate computing using resistive memory based Ternary Content Addressable Memory is becoming widely used. In this paper, a simplified model based analysis of a 2T2M-Ternary Content Addressable Memory using memristors is introduced. A comprehensive study is presented taking into consideration different circuit parameters and parasitic effects. Parameters such as the memristor Rh/Rl ratio, transistor technology, operating frequency, and memory width are taken into consideration. The proposed model is verified with SPICE showing a high degree of matching between theory and simulation. The utility of the model is established using a design example.

Design and analysis of 2T-2M Ternary content addressable memories

KAUST Repository

Bahloul, M. A.

2017-10-24

Associate and approximate computing using resistive memory based Ternary Content Addressable Memory is becoming widely used. In this paper, a simplified model based analysis of a 2T2M-Ternary Content Addressable Memory using memristors is introduced. A comprehensive study is presented taking into consideration different circuit parameters and parasitic effects. Parameters such as the memristor Rh/Rl ratio, transistor technology, operating frequency, and memory width are taken into consideration. The proposed model is verified with SPICE showing a high degree of matching between theory and simulation. The utility of the model is established using a design example.

Monitoring ligand-dependent assembly of receptor ternary complexes in live cells by BRETFect.

Science.gov (United States)

Cotnoir-White, David; El Ezzy, Mohamed; Boulay, Pierre-Luc; Rozendaal, Marieke; Bouvier, Michel; Gagnon, Etienne; Mader, Sylvie

2018-03-13

There is currently an unmet need for versatile techniques to monitor the assembly and dynamics of ternary complexes in live cells. Here we describe bioluminescence resonance energy transfer with fluorescence enhancement by combined transfer (BRETFect), a high-throughput technique that enables robust spectrometric detection of ternary protein complexes based on increased energy transfer from a luciferase to a fluorescent acceptor in the presence of a fluorescent intermediate. Its unique donor-intermediate-acceptor relay system is designed so that the acceptor can receive energy either directly from the donor or indirectly via the intermediate in a combined transfer, taking advantage of the entire luciferase emission spectrum. BRETFect was used to study the ligand-dependent cofactor interaction properties of the estrogen receptors ERα and ERβ, which form homo- or heterodimers whose distinctive regulatory properties are difficult to dissect using traditional methods. BRETFect uncovered the relative capacities of hetero- vs. homodimers to recruit receptor-specific cofactors and regulatory proteins, and to interact with common cofactors in the presence of receptor-specific ligands. BRETFect was also used to follow the assembly of ternary complexes between the V2R vasopressin receptor and two different intracellular effectors, illustrating its use for dissection of ternary protein-protein interactions engaged by G protein-coupled receptors. Our results indicate that BRETFect represents a powerful and versatile technique to monitor the dynamics of ternary interactions within multimeric complexes in live cells.

The ternary systems Sc-Sm(Dy)-Si at 870 K

International Nuclear Information System (INIS)

Kotur, B.Ya.; Mokra, I.Ya.; Toporinskij, A.Ya.

1991-01-01

Isothermal cross sections of the ternary systems Sc-Sm-Si and Sc-Dy-Si at 870 K have been plotted. Investigation of scandium and disprosium in ternary systems have been examined by X-ray diffraction and microstructure analysis. Besides literary data on binary systems Sc-Si, Sm-Si, Dy-Si have been used. Formation of limited (Sc-Sm-Si, Sc-Dy-Si) and continuous (Sc-Dy-Si) solid solutions based on bisilicides of Sc and Sm(Dy) is discovered. Two and five ternary compounds in Sc-Sm-Si and Sc-Dy-Si systems have been determined and their crystal structure has been established. When investigating of Sc-(rare earth element)-Si ternary systems and should take into account the specific interaction of scandium and samarium with REE

Experimental study of the ternary Ag-Cu-In phase diagram

International Nuclear Information System (INIS)

Bahari, Zahra; Elgadi, Mohamed; Rivet, Jacques; Dugue, Jerome

2009-01-01

The phase diagram of the Ag-Cu-In system was investigated using powder X-ray diffraction (XRD), differential scanning calorimetry (DSC) and electron probe microanalysis (EPMA). Two isothermal sections (at 510 and 607 deg. C) and 15 isopletic sections were studied. The results showed seven ternary peritectics, one ternary eutectic and one ternary metatectic. A complete reaction scheme was constructed, the valleys were drawn and the liquidus surfaces were derived from DSC data in the entire composition range.

Experimental study of the ternary Ag-Cu-In phase diagram

Energy Technology Data Exchange (ETDEWEB)

Bahari, Zahra [Laboratoire de chimie physique et minerale, Faculte des sciences pharmaceutiques et biologiques, Universite Paris Descartes, avenue de l' Observatoire, 75006 Paris (France); Laboratoire de chimie du solide mineral (LCSM), Faculte des sciences, Universite Mohamed 1er, Route Sidi Maafa, B.P. 524, Oujda, Maroc (Morocco); Elgadi, Mohamed [Laboratoire de chimie du solide mineral (LCSM), Faculte des sciences, Universite Mohamed 1er, Route Sidi Maafa, B.P. 524, Oujda, Maroc (Morocco); Rivet, Jacques [Laboratoire de chimie physique et minerale, Faculte des sciences pharmaceutiques et biologiques, Universite Paris Descartes, avenue de l' Observatoire, 75006 Paris (France); Dugue, Jerome [Laboratoire de chimie physique et minerale, Faculte des sciences pharmaceutiques et biologiques, Universite Paris Descartes, avenue de l' Observatoire, 75006 Paris (France)], E-mail: jerome.dugue@univ-paris5.fr

2009-05-27

The phase diagram of the Ag-Cu-In system was investigated using powder X-ray diffraction (XRD), differential scanning calorimetry (DSC) and electron probe microanalysis (EPMA). Two isothermal sections (at 510 and 607 deg. C) and 15 isopletic sections were studied. The results showed seven ternary peritectics, one ternary eutectic and one ternary metatectic. A complete reaction scheme was constructed, the valleys were drawn and the liquidus surfaces were derived from DSC data in the entire composition range.

Observation of preformed electron-hole Cooper pairs in highly excited ZnO

NARCIS (Netherlands)

Versteegh, M.A.M.; van Lange, A.J.; Stoof, H.T.C.; Dijkhuis, J.I.

2012-01-01

Electrons and holes in a semiconductor form hydrogen-atom-like bound states, called excitons. At high electron-hole densities the attractive Coulomb force becomes screened and excitons can no longer exist. Bardeen-Cooper-Schrieffer theory predicts that at such high densities co-operative many-body

A self-template and self-activation co-coupling green strategy to synthesize high surface area ternary-doped hollow carbon microspheres for high performance supercapacitors.

Science.gov (United States)

Gao, Meng; Fu, Jianwei; Wang, Minghuan; Wang, Kai; Wang, Shaomin; Wang, Zhiwei; Chen, Zhimin; Xu, Qun

2018-04-06

Development of facile and cost-effective routes to achieve hierarchical porous and heteroatoms-doped carbon architectures is urgently needed for high-performance supercapacitor application. In our study, ternary-doped (nitrogen, phosphorus and oxygen) hollow carbon microspheres (NPO-HCSs) are fabricated by one-step pyrolysis of single poly(cyclotriphosphazene-co-phloroglucinol) (PCPP) microsphere, which is generated through a facile polymerization between hexachlorocyclotriphosphazene and phloroglucinol at mild conditions. The whole preparation process is not used any additional template or activating agent. The obtained NPO-HCS-950 with average diameter of 580 nm and shell thickness of about 80 nm have a high specific surface area (2390 m 2  g -1 ), a large pore volume (1.35 cm 3  g -1 ), hierarchically interconnected pore texture, and uniform ternary heteroatom doping (O: 3.04 at%; N: 1.33 at% and P: 0.67 at%). As an electrode material for supercapacitors, the specific capacitance of the NPO-HCS-950 reaches 253 F g -1 of 1 A g - 1 and 176 F g -1 at 20 A g -1 , revealing superior rate performance. The capacity retention after 10,000 consecutive charge-discharge cycles at 20 A g -1 is up to 98.9%, demonstrating excellent cycling stability. Moreover, the assembled symmetric supercapacitor using NPO-HCS-950 exhibits a relatively high energy density of 17.6 W h kg -1 at a power density of 800 W kg -1 . Thus, a promising electrode material for high-performance supercapacitors is obtained through a facile, green and scalable synthesis route. Copyright © 2018 Elsevier Inc. All rights reserved.

Ternary manganese ferrite/graphene/polyaniline nanostructure with enhanced electrochemical capacitance performance

Science.gov (United States)

Xiong, Pan; Hu, Chenyao; Fan, Ye; Zhang, Wenyao; Zhu, Junwu; Wang, Xin

2014-11-01

A ternary manganese ferrite/graphene/polyaniline (MGP) nanostructure is designed and synthesized via a facile two-step approach. This nanostructure exhibits outstanding electrochemical performances, such as high specific capacitance (454.8 F g-1 at 0.2 A g-1), excellent rate capability (75.8% capacity retention at 5 A g-1), and good cycling stability (76.4% capacity retention after 5000 cycles at 2 A g-1), which are superior to those of its individual components (manganese ferrite, reduced-graphene oxide, polyaniline) and corresponding binary hybrids (manganese ferrite/graphene (MG), manganese ferrite/polyaniline (MP), and graphene/polyaniline (GP)). A symmetric supercapacitor device using the as-obtained hybrid has been fabricated and tested. The device exhibits a high specific capacitance of 307.2 F g-1 at 0.1 A g-1 with a maximum energy density of 13.5 W h kg-1. The high electrochemical performance of ternary MGP can be attributed to its well-designed nanostructure and the synergistic effect of the individual components.

Electrochemical studies on electroless ternary and quaternary Ni-P based alloys

International Nuclear Information System (INIS)

Balaraju, J.N.; Selvi, V. Ezhil; Grips, V.K. William; Rajam, K.S.

2006-01-01

The autocatalytic (electroless) deposition of Ni-P based alloys is a well-known commercial process that has found numerous applications because of their excellent anticorrosive, wear, magnetic, solderable properties, etc. It is a barrier coating, protecting the substrate by sealing it off from the corrosive environments, rather than by sacrificial action. The corrosion resistance varies with the phosphorus content of the deposit: relatively high for a high-phosphorus electroless nickel deposit but low for a low-phosphorus electroless nickel deposit. In the present investigation ternary Ni-W-P alloy films were prepared using alkaline citrate-based bath. Quaternary Ni-W-Cu-P films were deposited by the addition of 3 mM copper ions in ternary Ni-W-P bath. X-ray diffraction (XRD) studies indicated that all the deposits were nanocrystalline, i.e. 1.2, 2.1 and 6.0 nm, respectively, for binary, ternary and quaternary alloys. Corrosion resistance of the films was evaluated in 3.5% sodium chloride solution in non-deaerated and deaerated conditions by potentiodynamic polarization and electrochemical impedance (EIS) methods. Lower corrosion current density values were obtained for the coatings tested in deaerated condition. EIS studies showed that higher charge transfer resistance values were obtained for binary Ni-P coatings compared to ternary or quaternary coatings. For all the coatings a gradual increase in the anodic current density had been observed beyond 740 mV. In deaerated condition all the reported coatings exhibited a narrow passive region and all the values of E p , E tp and i pass were very close showing no major changes in the electrochemical behavior. In the non-deaerated conditions no passivation behavior had been observed for all these coatings

Cooperative Cloudlet for Pervasive Networks

Directory of Open Access Journals (Sweden)

Tauseef Jamal

2017-05-01

Full Text Available The notion of cooperation in wireless communication has got significant attention from both academia and industrial persons towards to address the performance drawbacks of wireless sensor network due to reason of user’s high mobility and lack of resources of network. The future wireless systems should be highly heterogeneous and interconnected because motivating cooperative relaying has to apply on the future mobile network for efficient results and future demand. As currently the mobile computing is facing latency and battery drainage issues which need to address and solve hence in this work we are proposed mobile - centric and opportunistic communication architecture. In this work mobile devices which are in the range of Wi - Fi of each other can create cluste r with each other and can create an ad - hoc cooperative cloud using Relay Spot[1 - 4]. The Collaboration between these devices can enable them to resourcefully use the augmentation without any infrastructure.

Positron annihilation lifetime study of interfaces in ternary polymer blends

International Nuclear Information System (INIS)

Meghala, D; Ramya, P; Pasang, T; Raj, J M; Ranganathaiah, C; Williams, J F

2013-01-01

A new method based on positron lifetime spectroscopy is developed to characterize individual interfaces in ternary polymer blends and hence determine the composition dependent miscibility level. The method owes its origin to the Kirkwood-Risemann-Zimm (KRZ) model for the evaluation of the hydrodynamic interaction parameters (α ij ) which was used successfully for a binary blend with a single interface. The model was revised for the present work for ternary polymer blends to account for three interfaces. The efficacy of this method is shown for two ternary blends namely poly(styrene-co-acrylonitrile)/poly (ethylene-co-vinylacetate)/poly(vinyl chloride) (SAN/EVA/PVC) and polycaprolactone /poly(styrene-co-acrylonitrile)/poly(vinyl chloride) (PCL/SAN/PVC) at different compositions. An effective hydrodynamic interaction parameter, α eff , was introduced to predict the overall miscibility of ternary blends.

Towards cooperative guidance and control of highly automated vehicles: H-Mode and Conduct-by-Wire.

Science.gov (United States)

Flemisch, Frank Ole; Bengler, Klaus; Bubb, Heiner; Winner, Hermann; Bruder, Ralph

2014-01-01

This article provides a general ergonomic framework of cooperative guidance and control for vehicles with an emphasis on the cooperation between a human and a highly automated vehicle. In the twenty-first century, mobility and automation technologies are increasingly fused. In the sky, highly automated aircraft are flying with a high safety record. On the ground, a variety of driver assistance systems are being developed, and highly automated vehicles with increasingly autonomous capabilities are becoming possible. Human-centred automation has paved the way for a better cooperation between automation and humans. How can these highly automated systems be structured so that they can be easily understood, how will they cooperate with the human? The presented research was conducted using the methods of iterative build-up and refinement of framework by triangulation, i.e. by instantiating and testing the framework with at least two derived concepts and prototypes. This article sketches a general, conceptual ergonomic framework of cooperative guidance and control of highly automated vehicles, two concepts derived from the framework, prototypes and pilot data. Cooperation is exemplified in a list of aspects and related to levels of the driving task. With the concept 'Conduct-by-Wire', cooperation happens mainly on the guidance level, where the driver can delegate manoeuvres to the automation with a specialised manoeuvre interface. With H-Mode, a haptic-multimodal interaction with highly automated vehicles based on the H(orse)-Metaphor, cooperation is mainly done on guidance and control with a haptically active interface. Cooperativeness should be a key aspect for future human-automation systems. Especially for highly automated vehicles, cooperative guidance and control is a research direction with already promising concepts and prototypes that should be further explored. The application of the presented approach is every human-machine system that moves and includes high

A combined theoretical and experimental approach of a new ternary metal oxide in molybdate composite for hybrid energy storage capacitors

Science.gov (United States)

Minakshi, M.; Watcharatharapong, T.; Chakraborty, S.; Ahuja, R.

2018-04-01

Sustainable energy sources require an efficient energy storage system possessing excellent electrochemical properties. The better understanding of possible crystal configurations and the development of a new ternary metal oxide in molybdate composite as an electrode for hybrid capacitors can lead to an efficient energy storage system. Here, we reported a new ternary metal oxide in molybdate composite [(Mn1/3Co1/3Ni1/3)MoO4] prepared by simple combustion synthesis with an extended voltage window (1.8 V vs. Carbon) resulting in excellent specific capacity 35 C g-1 (58 F g-1) and energy density (50 Wh kg-1 at 500 W kg-1) for a two electrode system in an aqueous NaOH electrolyte. The binding energies measured for Mn, Co, and Ni 2p are consistent with the literature, and with the metal ions being present as M(II), implying that the oxidation states of the transition metals are unchanged. The experimental findings are correlated well through density functional theory based electronic structure calculations. Our reported work on the ternary metal oxide studies (Mn1/3Co1/3Ni1/3)MoO4 suggests that will be an added value to the materials for energy storage.

Cooperativity effect involving drug-DNA/RNA intermolecular interaction: A B3LYP-D3 and MP2 theoretical investigation on ketoprofen⋯cytosine⋯H2O system.

Science.gov (United States)

Zhen, Jun-Ping; Wei, Xiao-Chun; Shi, Wen-Jing; Huang, Zhu-Yuan; Jin, Bo; Zhou, Yu-Kun

2017-11-14

In order to examine the origin of the drug action and design new DNA/RNA-targeted drugs, the cooperativity effect involving drug-DNA/RNA intermolecular interaction in ketoprofen⋯cytosine⋯H 2 O ternary system were investigated by the B3LYP, B3LYP-D3, and MP2 methods with the 6-311++G(2d,p) basis set. The thermodynamic cooperativity was also evaluated at 310.15 K. The N-H⋯O, O-H⋯O, O-H⋯N, C-H⋯N, and C-H⋯O H bonds coexist in ternary complexes. The intermolecular interactions obtained by B3LYP-D3 are close to those calculated by MP2. The steric effects and van der Waals interactions have little influence on the cooperativity effects. The anti-cooperativity effect in ket⋯cyt⋯H 2 O is far more notable than the cooperativity effect, and the stability of the cyclic structure with anti-cooperativity effect is higher than that of the linear structure with cooperativity effect, as is confirmed by the AIM (atoms in molecules) and RDG (reduced density gradient) analysis. Thus, it can be inferred that, in the presence of H 2 O, the anti-cooperativity effect plays a dominant role in the drug-DNA/RNA interaction, and the nature of the hydration in the binding of drugs to DNA/RNA bases is the H-bonding anti-cooperativity effect. Furthermore, the drug always links simultaneously with DNA/RNA base and H 2 O, and only in this way can the biological activity of drugs play a role. In most cases, the enthalpy change is the major factor driving the cooperativity, as is different from most of biomacromolecule complexes.

Ternary reduced-graphene-oxide/Bi2MoO6/Au nanocomposites with enhanced photocatalytic activity under visible light

International Nuclear Information System (INIS)

Bi, Jinhong; Fang, Wei; Li, Li; Li, Xiaofen; Liu, Minghua; Liang, Shijing; Zhang, Zizhong; He, Yunhui; Lin, Huaxiang; Wu, Ling; Liu, Shengwei; Wong, Po Keung

2015-01-01

A novel ternary nanocomposite photocatalyst consisted of reduced-graphene-oxide (RGO), Bi 2 MoO 6 and plasmonic Au nanoparticles were successfully fabricated by multiple steps including a simple solvothermal process and photochemical reduction process. RGO/Bi 2 MoO 6 /Au was characterized by X-ray powder diffraction patterns, transmission electron microscopy, UV–vis diffuse reflectance spectra, Raman spectroscopy and X-ray photoelectron spectroscopy. In comparison with Bi 2 MoO 6 , RGO/Bi 2 MoO 6 and Au/Bi 2 MoO 6 , RGO/Bi 2 MoO 6 /Au exhibits an enhanced photocatalytic activity for decomposition of Rhodamine B under visible light. The separation efficiency of the photogenerated holes and electrons on Bi 2 MoO 6 is promoted by the combined effect of both RGO and Au in the ternary composite, and thus enhances photocatalytic activity. The scavenger study revealed that both hole and superoxide are the major reactive species for the photocatalytic degradation of Rhodamine B using RGO/Bi 2 MoO 6 /Au photocatalyst. - Graphical abstract: A novel ternary nanocomposite photocatalyst consisted of reduced-graphene-oxide (RGO), Bi 2 MoO 6 and plasmonic Au nanoparticles were successfully fabricated by multiple steps including a simple solvothermal process and photochemical reduction process. The resulted ternary nanocomposites greatly enhanced the visible light photocatalytic properties compared to Bi 2 MoO 6 , RGO/Bi 2 MoO 6 or Au/Bi 2 MoO 6 binary systems. The improved photocatalytic activity was mainly attributed to the synergistic effect of Au and RGO with better separation of the photogenerated holes and electrons, resulting from the surface plasmonic resonance and extra strong electron magnetic field of Au nanoparticles and the high electron conductivity of RGO. - Highlights: • The ternary nanocomposites RGO/Bi 2 MoO 6 /Au were constructed for the first time. • RGO/Bi 2 MoO 6 /Au showed much higher visible photoactivity than RGO (Au)/Bi 2 MoO 6 . • The improved

Embedding complete ternary tree in hypercubes using AVL trees

NARCIS (Netherlands)

S.A. Choudum; I. Raman (Indhumathi)

2008-01-01

htmlabstractA complete ternary tree is a tree in which every non-leaf vertex has exactly three children. We prove that a complete ternary tree of height h, TTh, is embeddable in a hypercube of dimension . This result coincides with the result of [2]. However, in this paper, the embedding utilizes

Binary and ternary recombination of D3+ ions with electrons in He-D2 plasma

International Nuclear Information System (INIS)

Glosik, J.; Korolov, I.; Plasil, R.; Kotrik, T.; Dohnal, P.; Novotny, O.; Varju, J.; Roucka, S.; Greene, Chris H.; Kokoouline, V.

2009-01-01

An experimental study is reported about the recombination of D 3 + ions with electrons in a low-temperature plasma (200-300 K) consisting of He with a small admixture of D 2 . At several temperatures, the pressure dependence of the apparent binary recombination rate coefficient (α eff ) was measured over a broad range of helium pressures (200-2000 Pa). The binary and ternary recombination rate coefficients were obtained from measured pressure dependences of α eff . The binary recombination rate coefficient obtained α bin (300 K)=(2.7±0.9)x10 -8 cm 3 s -1 is in agreement with recent theory. The ternary recombination rate coefficient obtained is K He (300 K)=(1.8±0.6)x10 -25 cm 6 s -1 . In analogy with the recently described process of helium-assisted ternary recombination of H 3 + ions, it is suggested that the ternary helium-assisted recombination of D 3 + ions proceeds through the formation of a neutral long-lived highly excited Rydberg molecule D 3 followed by a collision with a He atom.

Binary and ternary recombination of D3+ ions with electrons in He-D2 plasma

Science.gov (United States)

Glosík, J.; Korolov, I.; Plašil, R.; Kotrík, T.; Dohnal, P.; Novotný, O.; Varju, J.; Roučka, Š.; Greene, Chris H.; Kokoouline, V.

2009-10-01

An experimental study is reported about the recombination of D3+ ions with electrons in a low-temperature plasma (200-300 K) consisting of He with a small admixture of D2 . At several temperatures, the pressure dependence of the apparent binary recombination rate coefficient (αeff) was measured over a broad range of helium pressures (200-2000 Pa). The binary and ternary recombination rate coefficients were obtained from measured pressure dependences of αeff . The binary recombination rate coefficient obtained αbin(300K)=(2.7±0.9)×10-8cm3s-1 is in agreement with recent theory. The ternary recombination rate coefficient obtained is KHe(300K)=(1.8±0.6)×10-25cm6s-1 . In analogy with the recently described process of helium-assisted ternary recombination of H3+ ions, it is suggested that the ternary helium-assisted recombination of D3+ ions proceeds through the formation of a neutral long-lived highly excited Rydberg molecule D3 followed by a collision with a He atom.

Energy dissipation in the process of ternary fission in heavy nuclear reaction

International Nuclear Information System (INIS)

Li Xian; Wang Chengqian; Yan Shiwei

2015-01-01

We studied the evolution of the collective motion, interaction potential, the total kinetic and excitation energies in ternary fissions of 197 Au + 197 Au system at 15 MeV/u, and discussed energy dissipation of this reaction. Through the comparison with energy-angle correlation data in binary fissions, we preliminarily concluded that the rst fission of ternary fission was an extreme deep-inelastic process. We further analyzed the correlation of the total kinetic energy with impact parameters in both binary and ternary reactions, and found that the total energy of binary reactions systems was lost about 150 MeV more than ternary fission with small impact parameters, and with larger impact parameters the total energy of ternary reactions were lost 300 MeV more than binary reactions. (authors)

Preparation and photoluminescence enhancement in terbium(III ternary complexes with β-diketone and monodentate auxiliary ligands

Directory of Open Access Journals (Sweden)

Devender Singh

2016-12-01

Full Text Available A series of new solid ternary complexes of terbium(III ion based on β-diketone ligand acetylacetone (acac and monodentate auxiliary ligands (aqua/urea/triphenylphosphineoxide/pyridine-N-oxide had been prepared. The structural characterizations of synthesized ternary compounds were studied by means of elemental analysis, infrared (IR, and proton nuclear magnetic resonance (NMR spectral techniques. The optical characteristics were investigated with absorption as well as photoluminescence spectroscopy. Thermal behavior of compounds was examined by TGA/DTA analysis and all metal complexes were found to have good thermal stability. The luminescence decay time of complexes were also calculated by monitoring at emission wavelength corresponding to 5D4 → 7F5 transition. A comparative inspection of the luminescent behavior of prepared ternary compounds was performed in order to determine the function of auxiliary ligands in the enhancement of luminescence intensity produced by central terbium(III ion. The color coordinates values suggested that compounds showed bright green emission in visible region in electromagnetic spectrum. Complexes producing green light could play a significant role in the fabrication of efficient light conversion molecular devices for display purposes and lightning systems.

Synergistic increase of oxygen reduction favourable Fe-N coordination structures in a ternary hybrid of carbon nanospheres/carbon nanotubes/graphene sheets.

Science.gov (United States)

Zhang, Shiming; Liu, Bin; Chen, Shengli

2013-11-14

A Fe/N co-doped ternary nanocarbon hybrid, with uniform bamboo-like carbon nanotubes (CNTs) in situ grown on/between the single/few-layer graphene sheets interspaced by carbon nanosphere aggregates, was prepared through a one-pot heat treatment of a precursor mixture containing graphene oxide, Vulcan XC-72 carbon nanospheres, nitrogen rich melamine and small amounts of Fe ions. Physical characterization including electron microscopic images, N2 adsorption-desorption isotherms, pore size distribution, XPS, XRD, Mössbauer spectra, and EDX revealed that the 0-D/1-D/2-D ternary hybrid architecture not only offered an optimized morphology for high dispersion of each nanocarbon moiety, while the carbon nanosphere interspaced graphene sheets have provided a platform for efficient reaction between Fe ions and melamine molecules, resulting in uniform nucleation and growth of CNTs and formation of high density Fe-N coordination assemblies that have been believed to be the active centers for the oxygen reduction reaction (ORR) in carbon-based nonprecious metal electrocatalysts. In the absence of graphene oxides or carbon nanospheres, a similar heat treatment was found to result in large amounts of elemental Fe and Fe carbides and entangled CNTs with wide diameter distributions. As a result, the ternary Fe/N-doped nanocarbon hybrid exhibits ORR activity much higher than the Fe-N doped single or binary nanocarbon materials prepared under similar heat treatment conditions, and approaching that of the state-of-the-art carbon-supported platinum catalyst (Pt/C) in acidic media, as well as superior stability and methanol tolerance to Pt/C.

Infrared target recognition based on improved joint local ternary pattern

Science.gov (United States)

Sun, Junding; Wu, Xiaosheng

2016-05-01

This paper presents a simple, efficient, yet robust approach, named joint orthogonal combination of local ternary pattern, for automatic forward-looking infrared target recognition. It gives more advantages to describe the macroscopic textures and microscopic textures by fusing variety of scales than the traditional LBP-based methods. In addition, it can effectively reduce the feature dimensionality. Further, the rotation invariant and uniform scheme, the robust LTP, and soft concave-convex partition are introduced to enhance its discriminative power. Experimental results demonstrate that the proposed method can achieve competitive results compared with the state-of-the-art methods.

Ternary Pt9RhFex Nanoscale Alloys as Highly Efficient Catalysts with Enhanced Activity and Excellent CO-Poisoning Tolerance for Ethanol Oxidation.

Science.gov (United States)

Wang, Peng; Yin, Shibin; Wen, Ying; Tian, Zhiqun; Wang, Ningzhang; Key, Julian; Wang, Shuangbao; Shen, Pei Kang

2017-03-22

To address the problems of high cost and poor stability of anode catalysts in direct ethanol fuel cells (DEFCs), ternary nanoparticles Pt 9 RhFe x (x = 1, 3, 5, 7, and 9) supported on carbon powders (XC-72R) have been synthesized via a facile method involving reduction by sodium borohydride followed by thermal annealing in N 2 at ambient pressure. The catalysts are physically characterized by X-ray diffraction, scanning transmission electron microscopy, and X-ray photoelectron spectroscopy, and their catalytic performance for the ethanol oxidation reaction (EOR) is evaluated by cyclic and linear scan voltammetry, CO-stripping voltammograms, and chronopotentiometry. All the Pt 9 RhFe x /C catalysts of different atomic ratios produce high EOR catalytic activity. The catalyst of atomic ratio composition 9:1:3 (Pt/Rh/Fe) has the highest activity and excellent CO-poisoning tolerance. Moreover, the enhanced EOR catalytic activity on Pt 9 RhFe 3 /C when compared to Pt 9 Rh/C, Pt 3 Fe/C, and Pt/C clearly demonstrates the presence of Fe improves catalytic performance. Notably, the onset potential for CO oxidation on Pt 9 RhFe 3 /C (0.271 V) is ∼55, 75, and 191 mV more negative than on Pt 9 Rh/C (0.326 V), Pt 3 Fe/C (0.346 V), and Pt/C (0.462 V), respectively, which implies the presence of Fe atoms dramatically improves CO-poisoning tolerance. Meanwhile, compared to the commercial PtRu/C catalyst, the peak potential on Pt 9 RhFe 3 /C for CO oxidation was just slightly changed after several thousand cycles, which shows high stability against the potential cycling. The possible mechanism by which Fe and Rh atoms facilitate the observed enhanced performance is also considered herein, and we conclude Pt 9 RhFe 3 /C offers a promising anode catalyst for direct ethanol fuel cells.

INTERVAL-VALUED INTUITIONISTIC FUZZY BI-IDEALS IN TERNARY SEMIRINGS

Directory of Open Access Journals (Sweden)

D. KRISHNASWAMY

2016-04-01

Full Text Available In this paper we introduce the notions of interval-valued fuzzy bi-ideal, interval-valued anti fuzzy bi-ideal and interval-valued intuitionistic fuzzy bi-ideal in ternary semirings and some of the basic properties of these ideals are investigated. We also introduce normal interval-valued intuitionistic fuzzy ideals in ternary semirings.

First-principles study of ternary fcc solution phases from special quasirandom structures

International Nuclear Information System (INIS)

Shin Dongwon; Wang Yi; Liu Zikui; Walle, Axel van de

2007-01-01

In the present work, ternary special quasirandom structures (SQSs) for a fcc solid solution phase are generated at different compositions, x A =x B =x C =(1/3) and x A =(1/2), x B =x C =(1/4), whose correlation functions are satisfactorily close to those of a random fcc solution. The generated SQSs are used to calculate the mixing enthalpy of the fcc phase in the Ca-Sr-Yb system. It is observed that first-principles calculations of all the binary and ternary SQSs in the Ca-Sr-Yb system exhibit very small local relaxation. It is concluded that the fcc ternary SQSs can provide valuable information about the mixing behavior of the fcc ternary solid solution phase. The SQSs presented in this work can be widely used to study the behavior of ternary fcc solid solutions

Ternary (liquid + liquid) equilibria of {trifluorotris(perfluoroethyl)phosphate based ionic liquids + thiophene + heptane}

International Nuclear Information System (INIS)

Marciniak, Andrzej; Królikowski, Marek

2012-01-01

Highlights: ► Ternary (liquid + liquid) equilibria for 3 ionic liquid + thiophene + heptane systems. ► The influence of ionic liquid structure on phase diagrams is discussed. ► High selectivity for separation of heptane/thiophene is observed. - Abstract: Ternary (liquid + liquid) equilibria for three systems containing ionic liquids {(4-(2-methoxyethyl)-4-methylmorpholinium trifluorotris(perfluoroethyl)phosphate, 1-(2-methoxyethyl)-1-methylpiperidinium trifluorotris(perfluoroethyl)phosphate, 1-(2-methoxyethyl)-1-methylpyrrolidinium trifluorotris(perfluoroethyl)phosphate) + thiophene + heptane} have been determined at T = 298.15 K. All systems showed high solubility of thiophene in the ionic liquid and low solubility of heptane. The solute distribution coefficient and the selectivity were calculated for all systems. High values of selectivity were obtained. The experimental results have been correlated using NRTL model. The influence of ionic liquid structure on phase equilibria is discussed.

The partially alternating ternary sum in an associative dialgebra

International Nuclear Information System (INIS)

Bremner, Murray R; Sanchez-Ortega, Juana

2010-01-01

The alternating ternary sum in an associative algebra, abc - acb - bac + bca + cab - cba, gives rise to the partially alternating ternary sum in an associative dialgebra with products dashv and vdash by making the argument a the center of each term. We use computer algebra to determine the polynomial identities in degree ≤9 satisfied by this new trilinear operation. In degrees 3 and 5, these identities define a new variety of partially alternating ternary algebras. We show that there is a 49-dimensional space of multilinear identities in degree 7, and we find equivalent nonlinear identities. We use the representation theory of the symmetric group to show that there are no new identities in degree 9.

Binary and ternary gas mixtures with temperature enhanced diffuse glow discharge characteristics for use in closing switches

Science.gov (United States)

Christophorou, L.G.; Hunter, S.R.

1990-06-26

An improvement to the gas mixture used in diffuse glow discharge closing switches is disclosed which includes binary and ternary gas mixtures which are formulated to exhibit decreasing electron attachment with increasing temperature. This increases the efficiency of the conductance of the glow discharge and further inhibits the formation of an arc. 11 figs.

α-ternary decay of Cf isotopes, statistical model

International Nuclear Information System (INIS)

Joseph, Jayesh George; Santhosh, K.P.

2017-01-01

The process of splitting a heavier nucleus to three simultaneous fragments is termed as ternary fission and compared to usual binary fission, it is a rare process. Depending on the nature of third particle either it is called light charged particle (LCP) accompanying fission if it is light or true ternary fission if all three fragments have nearly same mass distributions. After experimental observations in early seventies, initially with a slow pace, now theoretical studies in ternary fission has turned to a hot topic in nuclear decay studies especially in past one decade. Mean while various models have been developed, existing being modified and seeking for new with a hope that it can beam a little more light to the profound nature of nuclear interaction. In this study a statistical method, level density formulation, has been employed

Survey of the Economic Efficiency of Agricultural Cooperatives in the Buinzahra City and Prioritization of Their Problems Faced in the Management Process and the Marketing System

Directory of Open Access Journals (Sweden)

Mohammad Mahdi Mozaffari

2016-02-01

Full Text Available In this study Stochastic Data Envelopment Analysis method was used in order to estimate the economic efficiency of agricultural cooperatives in the Buinzahra city. Moreover, the Analytical Hierarchy Process method and Entropy criteria were used in order to prioritizate the agricultural cooperatives problems of this city in management and marketing system. The required dates were related to the years 2012-2013 during which data were collected by interviewing and completing questionnaires for 43 members of the cooperatives. The Random Sampling method and the Cochran formula were used to determine the sample size and from the Cronbach's Alpha method was used in order to evaluate the validity and reliability of the questionnaire. The results showed that the random efficiency average of agricultural cooperatives in Buinzahra city is at the low level (79 Percent and animal husbandry units have the lowest level of the efficiency. Also the results showed that inappropriate policies in the pricing and price volatility of agricultural products, the low level of services of packaging, processing, marketing and distribution of the products and the lack of long-term comprehensive planning by managers have the first, second and third ranks in the inefficiency of the management process and the marketing system of cooperatives in the study area respectively. Finally, the site locating studies before the establishment of cooperatives, providing funding and loans with low interest rates to animal husbandry units, transferring the experiences and expertise of successful cooperatives to inefficient cooperatives and strengthening and supporting the marketing system in order to resolve the problems facing the agricultural cooperatives of city Buinzahra were proposed based on the results obtained.

Adiabatic pipelining: a key to ternary computing with quantum dots

Science.gov (United States)

Pečar, P.; Ramšak, A.; Zimic, N.; Mraz, M.; Lebar Bajec, I.

2008-12-01

The quantum-dot cellular automaton (QCA), a processing platform based on interacting quantum dots, was introduced by Lent in the mid-1990s. What followed was an exhilarating period with the development of the line, the functionally complete set of logic functions, as well as more complex processing structures, however all in the realm of binary logic. Regardless of these achievements, it has to be acknowledged that the use of binary logic is in computing systems mainly the end result of the technological limitations, which the designers had to cope with in the early days of their design. The first advancement of QCAs to multi-valued (ternary) processing was performed by Lebar Bajec et al, with the argument that processing platforms of the future should not disregard the clear advantages of multi-valued logic. Some of the elementary ternary QCAs, necessary for the construction of more complex processing entities, however, lead to a remarkable increase in size when compared to their binary counterparts. This somewhat negates the advantages gained by entering the ternary computing domain. As it turned out, even the binary QCA had its initial hiccups, which have been solved by the introduction of adiabatic switching and the application of adiabatic pipeline approaches. We present here a study that introduces adiabatic switching into the ternary QCA and employs the adiabatic pipeline approach to successfully solve the issues of elementary ternary QCAs. What is more, the ternary QCAs presented here are sizewise comparable to binary QCAs. This in our view might serve towards their faster adoption.

Adiabatic pipelining: a key to ternary computing with quantum dots

International Nuclear Information System (INIS)

Pecar, P; Zimic, N; Mraz, M; Lebar Bajec, I; Ramsak, A

2008-01-01

The quantum-dot cellular automaton (QCA), a processing platform based on interacting quantum dots, was introduced by Lent in the mid-1990s. What followed was an exhilarating period with the development of the line, the functionally complete set of logic functions, as well as more complex processing structures, however all in the realm of binary logic. Regardless of these achievements, it has to be acknowledged that the use of binary logic is in computing systems mainly the end result of the technological limitations, which the designers had to cope with in the early days of their design. The first advancement of QCAs to multi-valued (ternary) processing was performed by Lebar Bajec et al, with the argument that processing platforms of the future should not disregard the clear advantages of multi-valued logic. Some of the elementary ternary QCAs, necessary for the construction of more complex processing entities, however, lead to a remarkable increase in size when compared to their binary counterparts. This somewhat negates the advantages gained by entering the ternary computing domain. As it turned out, even the binary QCA had its initial hiccups, which have been solved by the introduction of adiabatic switching and the application of adiabatic pipeline approaches. We present here a study that introduces adiabatic switching into the ternary QCA and employs the adiabatic pipeline approach to successfully solve the issues of elementary ternary QCAs. What is more, the ternary QCAs presented here are sizewise comparable to binary QCAs. This in our view might serve towards their faster adoption.

Adiabatic pipelining: a key to ternary computing with quantum dots.

Science.gov (United States)

Pečar, P; Ramšak, A; Zimic, N; Mraz, M; Lebar Bajec, I

2008-12-10

The quantum-dot cellular automaton (QCA), a processing platform based on interacting quantum dots, was introduced by Lent in the mid-1990s. What followed was an exhilarating period with the development of the line, the functionally complete set of logic functions, as well as more complex processing structures, however all in the realm of binary logic. Regardless of these achievements, it has to be acknowledged that the use of binary logic is in computing systems mainly the end result of the technological limitations, which the designers had to cope with in the early days of their design. The first advancement of QCAs to multi-valued (ternary) processing was performed by Lebar Bajec et al, with the argument that processing platforms of the future should not disregard the clear advantages of multi-valued logic. Some of the elementary ternary QCAs, necessary for the construction of more complex processing entities, however, lead to a remarkable increase in size when compared to their binary counterparts. This somewhat negates the advantages gained by entering the ternary computing domain. As it turned out, even the binary QCA had its initial hiccups, which have been solved by the introduction of adiabatic switching and the application of adiabatic pipeline approaches. We present here a study that introduces adiabatic switching into the ternary QCA and employs the adiabatic pipeline approach to successfully solve the issues of elementary ternary QCAs. What is more, the ternary QCAs presented here are sizewise comparable to binary QCAs. This in our view might serve towards their faster adoption.

Cooperation and the evolution of intelligence.

Science.gov (United States)

McNally, Luke; Brown, Sam P; Jackson, Andrew L

2012-08-07

The high levels of intelligence seen in humans, other primates, certain cetaceans and birds remain a major puzzle for evolutionary biologists, anthropologists and psychologists. It has long been held that social interactions provide the selection pressures necessary for the evolution of advanced cognitive abilities (the 'social intelligence hypothesis'), and in recent years decision-making in the context of cooperative social interactions has been conjectured to be of particular importance. Here we use an artificial neural network model to show that selection for efficient decision-making in cooperative dilemmas can give rise to selection pressures for greater cognitive abilities, and that intelligent strategies can themselves select for greater intelligence, leading to a Machiavellian arms race. Our results provide mechanistic support for the social intelligence hypothesis, highlight the potential importance of cooperative behaviour in the evolution of intelligence and may help us to explain the distribution of cooperation with intelligence across taxa.

Ternary fission of spontaneously fissile uranium isomers excited by neutrons

International Nuclear Information System (INIS)

Makarenko, V.E.; Molchanov, Y.D.; Otroshchenko, G.A.; Yan'kov, G.B.

1989-01-01

Spontaneously fissile isomers (SFI) of uranium were excited in the reactions 236,238 U(n,n') at an average neutron energy 4.5 MeV. A pulsed electrostatic accelerator and time analysis of the fission events were used. Fission fragments were detected by the scintillation method, and long-range particles from fission were detected by an ionization method. The relative probability of fission of nuclei through a spontaneously fissile isomeric state was measured: (1.30±0.01)·10 -4 ( 236 U) and (1.48±0.02)·10 -4 ( 238 U). Half-lives of the isomers were determined: 121±2 nsec (the SFI 236 U) and 267±13 nsec (the SFI 238 U). In study of the ternary fission of spontaneously fissile isotopes of uranium it was established that the probability of the process amounts to one ternary fission per 163±44 binary fissions of the SFI 236 U and one ternary fission per 49±14 binary fissions of the SFI 238 U. The substantial increase of the probability of ternary fission of SFI of uranium in comparison with the case of ternary fission of nuclei which are not in an isomeric state may be related to a special nucleon configuration of the fissile isomers of uranium

Gender differences in cooperation: experimental evidence on high school students.

Directory of Open Access Journals (Sweden)

J Alberto Molina

Full Text Available The emergence of cooperation among unrelated human subjects is a long-standing conundrum that has been amply studied both theoretically and experimentally. Within the question, a less explored issue relates to the gender dependence of cooperation, which can be traced back to Darwin, who stated that "women are less selfish but men are more competitive". Indeed, gender has been shown to be relevant in several game theoretical paradigms of social cooperativeness, including prisoner's dilemma, snowdrift and ultimatum/dictator games, but there is no consensus as to which gender is more cooperative. We here contribute to this literature by analyzing the role of gender in a repeated Prisoners' Dilemma played by Spanish high-school students in both a square lattice and a heterogeneous network. While the experiment was conducted to shed light on the influence of networks on the emergence of cooperation, we benefit from the availability of a large dataset of more 1200 participants. We applied different standard econometric techniques to this dataset, including Ordinary Least Squares and Linear Probability models including random effects. All our analyses indicate that being male is negatively associated with the level of cooperation, this association being statistically significant at standard levels. We also obtain a gender difference in the level of cooperation when we control for the unobserved heterogeneity of individuals, which indicates that the gender gap in cooperation favoring female students is present after netting out this effect from other socio-demographics factors not controlled for in the experiment, and from gender differences in risk, social and competitive preferences.

Binary and ternary solid-liquid phase equilibrium for the systems formed by succinic acid, urea and diethylene glycol: Determination and modelling

International Nuclear Information System (INIS)

Li, Yanxun; Li, Congcong; Han, Shuo; Zhao, Hongkun

2017-01-01

Highlights: • Solubility of succinic acid in diethylene glycol was determined. • Solubility of succinic acid + urea + diethylene glycol was determined. • Three ternary phase diagrams were constructed for the ternary system. • The ternary phase diagrams were correlated using NRTL model. - Abstract: In this work, the solid-liquid phase equilibrium for binary system of succinic acid + diethylene glycol at the temperatures ranging from (298.15 to 333.15) K and ternary system of (succinic acid + urea + diethylene glycol) at 298.15 K, 313.15 K and 333.15 K was built by using the isothermal saturation method under atmospheric pressure (101.2 kPa), and the solubilities were determined by a high-performance liquid chromatography. The solid-phases formed in the ternary system of ((succinic acid + urea + diethylene glycol)) were confirmed by Schreinemaker’s method of wet residue, which corresponded to urea, succinic acid, and adduct 2:1 urea-succinic acid (mole ratio). Three isothermal phase diagrams for the ternary system were constructed based on the measured mutual solubility. Each isothermal phase diagram included six crystallization fields, three invariant curves, two invariant points and two co-saturated points. The crystalline region of adduct 2:1 urea-succinic acid is larger than those of the other two solids. The solubility of succinic acid in diethylene glycol was correlated with the modified Apelblat equation, λh equation and NRTL model; and the mutual solubility of the ternary ((succinic acid + urea + diethylene glycol)) system was correlated and calculated by the NRTL model. The interaction parameters’ values of succinic acid-urea were acquired. The value of RMSD was 7.11 × 10 −3 for the ternary system. The calculation results had good agreement with the experiment values. Furthermore, the densities of equilibrium liquid phase were acquired. The phase diagrams and the thermodynamic model of the ternary system could provide the basis for design of

In vitro and in vivo gene delivery using chitosan/hyaluronic acid nanoparticles: Influences of molecular mass of hyaluronic acid and lyophilization on transfection efficiency.

Science.gov (United States)

Sato, Toshinori; Nakata, Mitsuhiro; Yang, Zhihong; Torizuka, Yu; Kishimoto, Satoko; Ishihara, Masayuki

2017-08-01

Lyophilization is an effective method for preserving nonviral gene vectors. To improve the stability and transgene expression of lyophilized plasmid DNA (pDNA) complexes, we coated the surfaces of pDNA/chitosan complexes with hyaluronic acid (HA) of varying molecular masses. The transgene expression of pDNA/chitosan/HA ternary complexes was characterized in vitro and in vivo. pDNA complexes were lyophilized overnight and the resultant products with spongy, porous consistencies were stored at -30, 4 or 25°C for 2 weeks. Rehydrated complexes were characterized using gel retardation assays, aiming to confirm complex formation, measure particle size and evaluate zeta potential, as well as conduct luciferase gene reporter assays. The anti-tumor effects of pDNA ternary complexes were evaluated using suicide gene (pTK) coding thymidine kinase in Huh7-implanted mice. Transfection efficiencies of pDNA/chitosan/HA ternary complexes were dependent on the average molecular masses of HA. The coating of pDNA/chitosan complexes with HA maintained the cellular transfection efficiencies of lyophilized pDNA ternary complexes. Furthermore, intratumoral injection of lyophilized, rehydrated pDNA ternary complexes into tumor-bearing mice showed a significant suppression of tumor growth. The coating of pDNA/chitosan complexes with high-molecular-weight HA augmented the stability and cellular transfection ability of the complexes after lyophilization-rehydration. Copyright © 2017 John Wiley & Sons, Ltd.

Measurement and correlation of critical properties for binary mixtures and ternary mixtures containing gasoline additives

International Nuclear Information System (INIS)

Wang, Lipu; Han, Kewei; Xia, Shuqian; Ma, Peisheng; Yan, Fangyou

2014-01-01

Highlights: • A high-pressure view cell was used to measure the critical properties of mixtures. • Three binary mixtures’ and three ternary mixtures’ critical properties were reported. • The experimental data of each system covered the whole mole fraction range. • The critical properties of the ternary mixtures were predicted with the PR–WS model. • Empirical equations were used to correlate the experimental results. - Abstract: The critical properties of three binary mixtures and three ternary mixtures containing gasoline additives (including methanol + 1-propanol, heptane + ethanol, heptane + 1-propanol, methanol + 1-propanol + heptane, methanol + 1-propanol + methyl tert-butyl ether (MTBE), and ethanol + heptane + MTBE) were determined by a high-pressure cell. All the critical lines of binary mixtures belong to the type I described by Scott and van Konynenburg. The system of methanol + 1-propanol showed little non-ideal behavior due to their similar molecular structures. The heptane + ethanol and heptane + 1-propanol systems showed visible non-ideal behavior for their great differences in molecular structure. The Peng–Robinson equation of state combined with the Wong–Sandler mixing rule (PR–WS) was applied to correlate the critical properties of binary mixtures. The critical points of the three ternary mixtures were predicted by the PR–WS model with the binary interaction parameters using the procedure proposed by Heidemann and Khalil. The predicted critical temperatures were in good agreement with the experimental values, while the predicted critical pressures differed from the measured values. The experimental values of binary mixtures were fitted well with the Redlich–Kister equation. The critical properties of ternary mixtures were correlated with the Cibulka’s equation, and the critical surfaces were plotted using the Cibulka’s equations

Constitutional studies of the molybdenum-ruthenium-palladium ternary system

International Nuclear Information System (INIS)

Cornish, L.A.; Pratt, J.N.

1997-01-01

An experimental and computational study has been made of phase equilibria in the Mo-Ru-Pd ternary system. The constitution of annealed binary and ternary alloys was investigated using optical and electron microscopy, X-ray diffraction and SEM phase analysis techniques. Limited thermodynamic measurements were made using the ZrO 2 solid electrolyte e.m.f. method. The data obtained from the various techniques were used to construct a ternary isothermal section at 1473 K. The experimentally determined section is compared with a calculated section for the same temperature, computed using thermodynamic coefficients derived solely from binary system information. Lattice parameters are reported for the b.c.c., f.c.c. and c.p.h. solid solutions and for the σ phase. (orig.)

Model for competitive binary and ternary ion-molecule reactions

International Nuclear Information System (INIS)

Herbst, E.

1985-01-01

A mechanism by which competitive binary and ternary ion-molecule reactions can occur is proposed. Calculations are undertaken for the specific system CH3(+) + NH3 + He which has been studied in the laboratory by Smith and Adams (1978), and the potential surface of which has been studied theoretically by Nobes and Radom (1983). It is shown that a potential-energy barrier in the exit channel prevents the rapid dissociation of collision complexes with large amounts of angular momentum and thereby allows collisional stabilization of the complexes. The calculated ternary-reaction rate coefficient is in good agreement with the experimental value, but a plot of the effective two-body rate coefficient of the ternary channel vs helium density does not quite show the observed saturation. 21 references

Formation and characterization of zein-propylene glycol alginate-surfactant ternary complexes: Effect of surfactant type.

Science.gov (United States)

Dai, Lei; Sun, Cuixia; Wei, Yang; Zhan, Xinyu; Mao, Like; Gao, Yanxiang

2018-08-30

In this study, zein, propylene glycol alginate (PGA) and surfactant ternary complexes were fabricated by antisolvent co-precipitation method. Two types of surfactants (rhamnolipid and lecithin) were applied to generate zein-PGA-rhamnolipid (Z-P-R) and zein-PGA-lecithin (Z-P-L) ternary complexes, respectively. Results showed that the surfactant types significantly affected the properties of ternary complexes. The formation of ternary complexes was mainly due to the non-covalent interactions such as hydrogen bonding, electrostatic interaction and hydrophobic interactions among zein, PGA and surfactants. Moreover, the thermal stability of ternary complexes was enhanced with increasing the levels of both surfactants. Notably, ternary complex dispersions exhibited better stability against pH from 2 to 8. Furthermore, a compact network structure was observed in Z-P-R ternary complex, while Z-P-L ternary complex remained the spherical structure. These findings would provide new insights into the development of novel delivery system and expand the options, when zein-based complexes were utilized under different environment conditions. Copyright © 2018 Elsevier Ltd. All rights reserved.

He and Be ternary spontaneous fission of sup 2 sup 5 sup 2 Cf

CERN Document Server

Hwang, J K; Ramayya, A V; Hamilton, J H

2002-01-01

Ternary and binary fission studies of sup 2 sup 5 sup 2 Cf have been carried out by using the Gammasphere detector array with light charged particle (LCD) detectors. The relative sup 4 He and sup 5 He ternary fission yields were determined. The kinetic energies of the sup 5 He and sup 4 He ternary particles were found to be approximately 11 and 16 MeV, respectively. The sup 5 He particles contribute 10-20 % to the total observed alpha ternary yield. The data indicate that in nuclei with octupole deformations the population for the negative parity bands might be enhanced in the alpha ternary fission. >From LCP-gamma double gated spectra, neutron multiplicity distributions for alpha ternary fission pairs were measured. The average neutron multiplicity decreases about 0.7 AMU in going from the binary to alpha ternary fission in the approximately same mass splittings (104-146). From the analysis of the gamma-gamma matrix gated on the sup 1 sup 0 Be particles, the two fragment pairs of sup 1 sup 3 sup 8 Xe - sup 1...

Tricolore. A flexible color scale for ternary compositions

DEFF Research Database (Denmark)

2018-01-01

tricolore is an R library providing a flexible color scale for the visualization of three-part/ternary compositions. Its main functionality is to color-code any ternary composition as a mixture of three primary colours and to draw a suitable color-key. tricolore flexibly adapts to different...... visualisation challenges via - discrete and continuous color support - support for unbalanced compositional data via centering - support for data with very narrow range via scaling - hue, chroma and lightness options...

A facile fabrication of plasmonic g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag ternary heterojunction visible-light photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Dai, Kai, E-mail: daikai940@chnu.edu.cn [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China); Lv, Jiali [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China); Lu, Luhua, E-mail: lhlu@cug.edu.cn [Faculty of Material Science and Chemical Engineering, China University of Geosciences, Wuhan, 430074 (China); Liang, Changhao [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China); Key Laboratory of Materials Physics and Anhui Key Laboratory of Nanomaterials and Nanotechnology, Institute of Solid State Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei, 230031 (China); Geng, Lei; Zhu, Guangping [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China)

2016-07-01

It's important to reduce recombination of electrons and holes and enhance charge transfer through fine controlled interfacial structure. In this work, novel graphitic-C{sub 3}N{sub 4} (g-C{sub 3}N{sub 4})/Ag{sub 2}WO{sub 4}/Ag ternary photocatalyst has been synthesized by deposition of Ag{sub 2}WO{sub 4} onto g-C{sub 3}N{sub 4} template and followed by sun light reduction of Ag{sub 2}WO{sub 4} into Ag{sub 2}WO{sub 4}/Ag. As-prepared g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag presented significantly enhanced photocatalytic performance in degrading methylene blue (MB) under 410 nm LED light irradiation. Metallic Ag{sup 0} is used as plasmonic hot spots to generate high energy charge carriers. Optimal g-C{sub 3}N{sub 4} content has been confirmed to be 40 wt%, corresponding to apparent pseudo-first-order rate constant kapp of 0.0298 min{sup −1}, which is 3.3 times and 37.3 times more than that of pure g-C{sub 3}N{sub 4} and Ag{sub 2}WO{sub 4}, respectively. This novel ternary g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag structure material is an ideal candidate in environmental treatment and purifying applications. - Graphical abstract: A high efficient plasmonic graphitic-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag ternary nanocomposite photocatalyst was synthesized. - Highlights: • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag ternary nanocomposite photocatalyst was prepared. • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag showed high photocatalytic activity. • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag showed long reusable life.

An insight into the mechanism of charge-transfer of hybrid polymer:ternary/quaternary chalcopyrite colloidal nanocrystals

Directory of Open Access Journals (Sweden)

Parul Chawla

2014-08-01

Full Text Available In this work, we have demonstrated the structural and optoelectronic properties of the surface of ternary/quaternary (CISe/CIGSe/CZTSe chalcopyrite nanocrystallites passivated by tri-n-octylphosphine-oxide (TOPO and tri-n-octylphosphine (TOP and compared their charge transfer characteristics in the respective polymer: chalcopyrite nanocomposites by dispersing them in poly(3-hexylthiophene polymer. It has been found that CZTSe nanocrystallites due to their high crystallinity and well-ordered 3-dimensional network in its pristine form exhibit a higher steric- and photo-stability, resistance against coagulation and homogeneity compared to the CISe and CIGSe counterparts. Moreover, CZTSe nanocrystallites display efficient photoluminescence quenching as evident from the high value of the Stern–Volmer quenching constant (KSV and eventually higher charge transfer efficiency in their respective polymer P3HT:CZTSe composites. We modelled the dependency of the charge transfer from the donor and the charge separation mechanism across the donor–acceptor interface from the extent of crystallinity of the chalcopyrite semiconductors (CISe/CIGSe/CZTSe. Quaternary CZTSe chalcopyrites with their high crystallinity and controlled morphology in conjunction with regioregular P3HT polymer is an attractive candidate for hybrid solar cells applications.

An insight into the mechanism of charge-transfer of hybrid polymer:ternary/quaternary chalcopyrite colloidal nanocrystals.

Science.gov (United States)

Chawla, Parul; Singh, Son; Sharma, Shailesh Narain

2014-01-01

In this work, we have demonstrated the structural and optoelectronic properties of the surface of ternary/quaternary (CISe/CIGSe/CZTSe) chalcopyrite nanocrystallites passivated by tri-n-octylphosphine-oxide (TOPO) and tri-n-octylphosphine (TOP) and compared their charge transfer characteristics in the respective polymer: chalcopyrite nanocomposites by dispersing them in poly(3-hexylthiophene) polymer. It has been found that CZTSe nanocrystallites due to their high crystallinity and well-ordered 3-dimensional network in its pristine form exhibit a higher steric- and photo-stability, resistance against coagulation and homogeneity compared to the CISe and CIGSe counterparts. Moreover, CZTSe nanocrystallites display efficient photoluminescence quenching as evident from the high value of the Stern-Volmer quenching constant (K SV) and eventually higher charge transfer efficiency in their respective polymer P3HT:CZTSe composites. We modelled the dependency of the charge transfer from the donor and the charge separation mechanism across the donor-acceptor interface from the extent of crystallinity of the chalcopyrite semiconductors (CISe/CIGSe/CZTSe). Quaternary CZTSe chalcopyrites with their high crystallinity and controlled morphology in conjunction with regioregular P3HT polymer is an attractive candidate for hybrid solar cells applications.

Calculation of ternary interdiffusion coefficients using a single diffusion couple

Czech Academy of Sciences Publication Activity Database

Čermák, Jiří; Rothová, Věra

2016-01-01

Roč. 54, č. 5 (2016), s. 305-314 ISSN 0023-432X R&D Projects: GA MŠk(CZ) ED1.1.00/02.0068 Institutional support: RVO:68081723 Keywords : diffusion * interdiffusion * ternary alloys * ternary diffusion coefficients Subject RIV: BJ - Thermodynamics Impact factor: 0.366, year: 2016

Crystallization, data collection and processing of the chymotrypsin–BTCI–trypsin ternary complex

Energy Technology Data Exchange (ETDEWEB)

Esteves, Gisele Ferreira; Teles, Rozeni Chagas Lima; Cavalcante, Nayara Silva; Neves, David; Ventura, Manuel Mateus [Laboratório de Biofísica, Instituto de Ciências Biológicas, Universidade de Brasília, 70910-900 Brasília-DF (Brazil); Barbosa, João Alexandre Ribeiro Gonçalves, E-mail: joao@lnls.br [Center for Structural Molecular Biology (CeBiME), Brazilian Synchrotron Light Laboratory (LNLS), CP 6192, 13083-970 Campinas-SP (Brazil); Freitas, Sonia Maria de, E-mail: joao@lnls.br [Laboratório de Biofísica, Instituto de Ciências Biológicas, Universidade de Brasília, 70910-900 Brasília-DF (Brazil)

2007-12-01

A ternary complex of the proteinase inhibitor (BTCI) with trypsin and chymotrypsin was crystallized and its crystal structure was solved by molecular replacement. A ternary complex of the black-eyed pea trypsin and chymotrypsin inhibitor (BTCI) with trypsin and chymotrypsin was crystallized by the sitting-drop vapour-diffusion method with 0.1 M HEPES pH 7.5, 10%(w/v) polyethylene glycol 6000 and 5%(v/v) 2-methyl-2,4-pentanediol as precipitant. BTCI is a small protein with 83 amino-acid residues isolated from Vigna unguiculata seeds and is able to inhibit trypsin and chymotrypsin simultaneously by forming a stable ternary complex. X-ray data were collected from a single crystal of the trypsin–BTCI–chymotrypsin ternary complex to 2.7 Å resolution under cryogenic conditions. The structure of the ternary complex was solved by molecular replacement using the crystal structures of the BTCI–trypsin binary complex (PDB code) and chymotrypsin (PDB code) as search models.

Crystallization, data collection and processing of the chymotrypsin–BTCI–trypsin ternary complex

International Nuclear Information System (INIS)

Esteves, Gisele Ferreira; Teles, Rozeni Chagas Lima; Cavalcante, Nayara Silva; Neves, David; Ventura, Manuel Mateus; Barbosa, João Alexandre Ribeiro Gonçalves; Freitas, Sonia Maria de

2007-01-01

A ternary complex of the proteinase inhibitor (BTCI) with trypsin and chymotrypsin was crystallized and its crystal structure was solved by molecular replacement. A ternary complex of the black-eyed pea trypsin and chymotrypsin inhibitor (BTCI) with trypsin and chymotrypsin was crystallized by the sitting-drop vapour-diffusion method with 0.1 M HEPES pH 7.5, 10%(w/v) polyethylene glycol 6000 and 5%(v/v) 2-methyl-2,4-pentanediol as precipitant. BTCI is a small protein with 83 amino-acid residues isolated from Vigna unguiculata seeds and is able to inhibit trypsin and chymotrypsin simultaneously by forming a stable ternary complex. X-ray data were collected from a single crystal of the trypsin–BTCI–chymotrypsin ternary complex to 2.7 Å resolution under cryogenic conditions. The structure of the ternary complex was solved by molecular replacement using the crystal structures of the BTCI–trypsin binary complex (PDB code) and chymotrypsin (PDB code) as search models

US/Japan Cooperation in High Energy Physics. Review of activities, 1988--1993

Energy Technology Data Exchange (ETDEWEB)

1993-11-16

The objective of the Implementing Arrangement was to further the energy programs of both countries by establishing a framework for cooperation in the field of high energy physics, including research, accelerator and detector instrumentation research and development, the fabrication and subsequent use of new experimental devices and facilities, and related joint efforts as may be mutually agreed. Over the years, this cooperation has been very effective and has strengthened the overall collaborative efforts and the understanding between our nations and their citizens. It has demonstrated to the world our ability to work together to attack difficult problems. High Energy Physics goes across national borders; the bond is clearly intellectual and common ground is shared for the benefit of all in a most effective manner. This review covers the activities conducted under the aegis of the US/Japan Committee for Cooperation in High Energy Physics during the past five years (1988--1993). This was the second such US review of the US/Japan cooperative activities; the first was held in 1987.

A comparative study of three ternary complexes prepared in different mixing orders of siRNA/redox-responsive hyperbranched poly (amido amine/hyaluronic acid

Directory of Open Access Journals (Sweden)

Chen CJ

2012-07-01

Full Text Available Cheng-Jun Chen,1 Zhi-Xia Zhao,1 Jian-Cheng Wang,1 En-Yu Zhao,1 Ling-Yan Gao,1 Shu-Feng Zhou,2 Xiao-Yan Liu,1 Wan-Liang Lu,1 Qiang Zhang11State Key Laboratory of Natural and Biomimetic Drugs, Department of Pharmaceutics, School of Pharmaceutical Science, Peking University, Beijing, People’s Republic of China; 2Department of Pharmaceutical Sciences, College of Pharmacy, University of South Florida, Tampa, FL, USAAbstract: In this study, a novel redox-responsive hyperbranched poly(amido amine (named PCD was synthesized and used as a cationic polymer to form a ternary complex with small interfering RNA (siRNA and hyaluronic acid (HA for siRNA delivery. Here, it is hypothesized that different mixing orders result in different assembly structures, which may affect the siRNA delivery efficiency. To investigate the effects of mixing orders on siRNA delivery efficiency in two human breast cancer cell lines, three ternary complexes with different mixing orders of siRNA/PCD/HA were prepared and characterized: mixing order I (initially prepared siRNA/PCD binary complex further coated by negatively charged HA, mixing order II (initially prepared HA/PCD binary complex further incubated with siRNA, and mixing order III (initially prepared siRNA/HA mixture further electrostatically compacted by positively charged PCD. With an optimized siRNA/PCD/HA charge ratio of 1/20/16, the particle sizes and zeta potentials of these ternary complexes were 124.8 nm and 27.3 mV (mixing order I, 147.5 nm and 29.9 mV (mixing order II, and 128.8 nm and 19.4 mV (mixing order III. Also, the effects on stability, cellular uptake, and gene silencing efficiency of siRNA formulated in ternary complexes with different mixing orders were investigated. The results showed that mixing orders I and III displayed better siRNA transfection and protection than mixing order II in human breast cancer MCF-7 and MDA-MB-231 cells. More interesting, at the siRNA/PCD/HA charge ratio of 1/20/16, the

Differences observed in the surface morphology and microstructure of Ni-Fe-Cu ternary thin films electrochemically deposited at low and high applied current densities

International Nuclear Information System (INIS)

Sarac, U; Kaya, M; Baykul, M C

2016-01-01

In this research, nanocrystalline Ni-Fe-Cu ternary thin films using electrochemical deposition technique were produced at low and high applied current densities onto Indium Tin Oxide (ITO) coated conducting glass substrates. Change of surface morphology and microstructural properties of the films were investigated. Energy dispersive X-ray spectroscopy (EDX) measurements showed that the Ni-Fe-Cu ternary thin films exhibit anomalous codeposition behaviour during the electrochemical deposition process. From the X-ray diffraction (XRD) analyses, it was revealed that there are two segregated phases such as Cu- rich and Ni-rich within the films. The crystallographic structure of the films was face-centered cubic (FCC). It was also observed that the film has lower lattice micro-strain and higher texture degree at high applied current density. Scanning electron microscopy (SEM) studies revealed that the films have rounded shape particles on the base part and cauliflower-like structures on the upper part. The film electrodeposited at high current density had considerably smaller rounded shape particles and cauliflower-like structures. From the atomic force microscopy (AFM) analyses, it was shown that the film deposited at high current density has smaller particle size and surface roughness than the film grown at low current density. (paper)

Comparison effectiveness of cooperative learning type STAD with cooperative learning type TPS in terms of mathematical method of Junior High School students

Science.gov (United States)

Wahyuni, A.

2018-05-01

This research is aimed to find out whether the model of cooperative learning type Student Team Achievement Division (STAD) is more effective than cooperative learning type Think-Pair-Share in SMP Negeri 7 Yogyakarta. This research was a quasi-experimental research, using two experimental groups. The population of research was all students of 7thclass in SMP Negeri 7 Yogyakarta that consists of 5 Classes. From the population were taken 2 classes randomly which used as sample. The instrument to collect data was a description test. Measurement of instrument validity use content validity and construct validity, while measuring instrument reliability use Cronbach Alpha formula. To investigate the effectiveness of cooperative learning type STAD and cooperative learning type TPS on the aspect of student’s mathematical method, the datas were analyzed by one sample test. Comparing the effectiveness of cooperative learning type STAD and TPS in terms of mathematical communication skills by using t-test. Normality test was not conducted because the sample of research more than 30 students, while homogeneity tested by using Kolmogorov Smirnov test. The analysis was performed at 5% confidence level.The results show as follows : 1) The model of cooperative learning type STAD and TPS are effective in terms of mathematical method of junior high school students. 2). STAD type cooperative learning model is more effective than TPS type cooperative learning model in terms of mathematical methods of junior high school students.

Reliability-Aware Cooperative Node Sleeping and Clustering in Duty-Cycled Sensors Networks

Directory of Open Access Journals (Sweden)

Jeungeun Song

2018-01-01

Full Text Available Duty-cycled sensor networks provide a new perspective for improvement of energy efficiency and reliability assurance of multi-hop cooperative sensor networks. In this paper, we consider the energy-efficient cooperative node sleeping and clustering problems in cooperative sensor networks where clusters of relay nodes jointly transmit sensory data to the next hop. Our key idea for guaranteeing reliability is to exploit the on-demand number of cooperative nodes, facilitating the prediction of personalized end-to-end (ETE reliability. Namely, a novel reliability-aware cooperative routing (RCR scheme is proposed to select k-cooperative nodes at every hop (RCR-selection. After selecting k cooperative nodes at every hop, all of the non-cooperative nodes will go into sleep status. In order to solve the cooperative node clustering problem, we propose the RCR-based optimal relay assignment and cooperative data delivery (RCR-delivery scheme to provide a low-communication-overhead data transmission and an optimal duty cycle for a given number of cooperative nodes when the network is dynamic, which enables part of cooperative nodes to switch into idle status for further energy saving. Through the extensive OPNET-based simulations, we show that the proposed scheme significantly outperforms the existing geographic routing schemes and beaconless geographic routings in wireless sensor networks with a highly dynamic wireless channel and controls energy consumption, while ETE reliability is effectively guaranteed.

Special quasirandom structures for binary/ternary group IV random alloys

KAUST Repository

Chroneos, Alexander I.

2010-06-01

Simulation of defect interactions in binary/ternary group IV semiconductor alloys at the density functional theory level is difficult due to the random distribution of the constituent atoms. The special quasirandom structures approach is a computationally efficient way to describe the random nature. We systematically study the efficacy of the methodology and generate a number of special quasirandom cells for future use. In order to demonstrate the applicability of the technique, the electronic structures of E centers in Si1-xGex and Si1-x -yGexSny alloys are discussed for a range of nearest neighbor environments. © 2010 Elsevier B.V. All rights reserved.

Analytical determination of distillation boundaries for ternary azeotropic systems

OpenAIRE

Marcilla Gomis, Antonio; Reyes Labarta, Juan Antonio; Velasco, Raúl; Serrano Cayuelas, María Dolores; Olaya López, María del Mar

2009-01-01

A new straight forward algorithm to calculate distillation boundaries in ternary azeotropic systems has been developed. The proposed method allows, using cubic splines, the calculation of distillation trajectories and the calculation of that corresponding to the searched distillation boundaries. The algorithm is applied to 4 ternary liquid-vapour systems to test its validity. Vicepresidency of Research (University of Alicante) and Generalitat Valenciana (GV/2007/125)

Effect on strength of ternary alloying additions in L12 intermetallics

International Nuclear Information System (INIS)

Wu Yuanpang.

1991-01-01

The thermodynamic properties of {111} antiphase boundaries (APBs) as well as the site preference of ternary additions in an A 3 B intermetallic with L1 2 structure are studied, using a thermodynamic model. A survey of the results from a variety of ternary alloying additions to Ni 3 Al has shown that there is a conflict in the actual role which solid solution strengthening plays in the athermal increment of yield strength. For instance, a good quantitative agreement with linear concentration law is observed only in alloys with stoichiometric compositions but not in the general case of non-stoichiometric alloys. In the light of the possibility that micro-segregation could explain the experimental discrepancy, the author extends the binary solid solution strengthening theory to the ternary system in an L1 2 structure for the four real systems of Ni-Al-Si, Ni-Al-Ti, Ni-Al-Hf, and Ni-Al-V. It is found that ternary site preference plays an important role in the ternary solid solution strengthening theory with L1 2 structure. Good quantitative agreement was found between the calculated and experimentally measured strength for both stoichiometric and nonstoichiometric alloys

Binary and ternary fission yields induced by 12C and 20Ne ions on 238U targets

International Nuclear Information System (INIS)

Otto, R.J.

1974-01-01

Evidence for ternary fission of 250 Cf* and 258 No* compound nuclei has been found. Relative cross section data for nuclides with masses between 24 Na and 161 Tb have been determined for 12 C bombardments of natural uranium at laboratory energies of 122 MeV, 113 MeV and 105 MeV. Relative cross section data for 8 nuclides between 24 Na and 66 Ni were sought for 20 Ne bombardments of natural uranium at 150 MeV laboratory energies. The binary fission fragment mass distribution for 238 U( 12 C,f) was determined by analysis of fission fragment recoil collection foils using radiochemical techniques and high resolution gamma ray spectroscopy. The results indicated the existence of a ternary fission branch similar to mass distributions obtained for He induced fission of Th, U, and Pu nuclei at intermediate energies. Comparison of the data with He induced ternary fission data obtained previously in this laboratory indicated an increase in the ternary fission probability with increasing Z 2 /A of the compound nucleus and with excitation energy. A shift of the binary-ternary fission product intersection point to lower mass numbers with increasing Z 2 /A and excitation energy of the compound nucleus was also observed. (Diss. Abstr. Int., B)

In vitro and in vivo siRNA delivery to hepatocyte utilizing ternary complexation of lactosylated dendrimer/cyclodextrin conjugates, siRNA and low-molecular-weight sacran.

Science.gov (United States)

Hayashi, Yuya; Higashi, Taishi; Motoyama, Keiichi; Jono, Hirofumi; Ando, Yukio; Arima, Hidetoshi

2018-02-01

In this study, we newly developed the ternary complexes consisting of lactosylated dendrimer (generation 3)/α-cyclodextrin conjugate (Lac-α-CDE), siRNA and the anionic polysaccharide sacrans, and evaluated their utility as siRNA transfer carriers. Three kinds of the low-molecular-weight sacrans, i.e. sacran (100) (Mw 44,889Da), sacran (1000) (Mw 943,692Da) and sacran (10,000) (Mw 1,488,281Da) were used. Lac-α-CDE/siRNA/sacran ternary complexes were prepared by adding the low-molecular-weight sacrans to the Lac-α-CDE/siRNA binary complex solution. Cellular uptake of the ternary complex with sacran (100) was higher than that of the binary complex or the other ternary complexes with sacran (1000) and sacran (10,000) in HepG2 cells. Additionally, the ternary complex possessed high serum resistance and endosomal escaping ability in HepG2 cells. High liver levels of siRNA and Lac-α-CDE were observed after the intravenous administration of the ternary complex rather than that of the binary complex. Moreover, intravenous administration of the ternary complex (siRNA 5mg/kg) induced the significant RNAi effect in the liver of mice with negligible change of blood chemistry values. Therefore, a ternary complexation of the Lac-α-CDE/siRNA binary complex with sacran is useful as a hepatocyte-specific siRNA delivery system. Copyright © 2017 Elsevier B.V. All rights reserved.

Dividing wall column: Improving thermal efficiency, energy savings and economic performance

International Nuclear Information System (INIS)

Aurangzeb, Md; Jana, Amiya K.

2016-01-01

Highlights: • A rigorous model is developed for a dividing wall column. • Heat transfer model for metal wall is proposed. • Performance improvement is quantified for a ternary system. • Thermal efficiency, energy savings and cost are three used indices. - Abstract: This work aims at investigating the performance improvement of a dividing wall column (DWC) for the separation of a ternary system. It is true that for fractionating a ternary mixture, at least a sequence of two conventional distillation columns is required. To improve energetic and economic potential, and reduce space requirement, two columns are proposed to merge into one shell with a dividing wall. For developing the mathematical model of a distillation column, we consider the effect of heat transfer through the metal wall placed at an intermediated position inside the cylindrical column. The simulated DWC model is verified using the Aspen Plus flowsheet simulator with a wide variety of phase equilibrium models. The superiority of this proposed heat integrated configuration is shown for a ternary hydrocarbon system over a conventional distillation sequence (CDS) in terms of mainly three performance indexes, namely thermal efficiency, energy savings and total annual cost (TAC). It is investigated that the dividing wall distillation scheme can secure a 37.5% energy efficiency, and a 22.6% savings in energy consumption and 23.23% in TAC. The promising performance can also be quantified in terms of a reasonably low payback period of 2.11 years.

Binary and ternary carbides and nitrides of the transition metals and their phase relations

International Nuclear Information System (INIS)

Holleck, H.

1981-01-01

The occurrance and the structure of the binary and ternary transition metal carbides and nitrides are described. Phase diagrams are assessed for most of the binary and ternary systems. Many ternary phase diagrams are published in this report for the first time. (orig.) [de

The ternary system nickel-nobium-carbon

International Nuclear Information System (INIS)

Stadelmaier, H.H.; Fiedler, M.L.

1975-01-01

The ternary system nickel-niobium-carbon was studied by metallographic and X-ray diffraction methods to produce a liquidus projection and an isothermal section at 1,100 0 C. The liquidus projection is dominated by a wide field of primary NbC that extends far into the nickel corner of the composition triangle. Only one ternary compound is observed in this system, an eta-carbide formed in a peritectoid reaction. It has a narrow homogeneity range at Ni 2 Nb 4 C, and its lattice constant in alloys quenched from 1,100 0 C varies between 11.659 and 11.667 A. No eta-carbide Ni 3 Nb 3 C or Ni 6 Nb 6 could be detected. (orig.) [de

Energy Efficient Authentication and Authorization for Multinode Cooperative Connectivity and Reliability

DEFF Research Database (Denmark)

Rohokale, Vandana M.

2013-01-01

their effective QoS via cooperation. The performance of wireless networks is greatly affected by some of the channel parameters such as bandwidth and power scarcity, multi-user interference, non-reliability due to signal fading, vulnerability to the attacks, etc. The cooperative diversity mechanism makes use...... of the benefits of wireless sensor network scalability in terms of cooperative resource sharing wherein multiple diversity channels are created that results into the higher transmission rates, increased throughput and coverage range, improvement in reliability and end-to-end performance and much more. Cooperative......Wireless communication is a great revolution but it still suffers from limited battery life, broken connections from multi-path fading and insufficient coverage. Simple cooperation can mak a big difference in coverage range, energy and battery life. In CWC, the active nodes may increase...

Multiscale approaches to high efficiency photovoltaics

Directory of Open Access Journals (Sweden)

Connolly James Patrick

2016-01-01

Full Text Available While renewable energies are achieving parity around the globe, efforts to reach higher solar cell efficiencies becomes ever more difficult as they approach the limiting efficiency. The so-called third generation concepts attempt to break this limit through a combination of novel physical processes and new materials and concepts in organic and inorganic systems. Some examples of semi-empirical modelling in the field are reviewed, in particular for multispectral solar cells on silicon (French ANR project MultiSolSi. Their achievements are outlined, and the limits of these approaches shown. This introduces the main topic of this contribution, which is the use of multiscale experimental and theoretical techniques to go beyond the semi-empirical understanding of these systems. This approach has already led to great advances at modelling which have led to modelling software, which is widely known. Yet, a survey of the topic reveals a fragmentation of efforts across disciplines, firstly, such as organic and inorganic fields, but also between the high efficiency concepts such as hot carrier cells and intermediate band concepts. We show how this obstacle to the resolution of practical research obstacles may be lifted by inter-disciplinary cooperation across length scales, and across experimental and theoretical fields, and finally across materials systems. We present a European COST Action “MultiscaleSolar” kicking off in early 2015, which brings together experimental and theoretical partners in order to develop multiscale research in organic and inorganic materials. The goal of this defragmentation and interdisciplinary collaboration is to develop understanding across length scales, which will enable the full potential of third generation concepts to be evaluated in practise, for societal and industrial applications.

Asymmetric supercapacitors with metal-like ternary selenides and porous graphene electrodes

KAUST Repository

Xia, Chuan; Jiang, Qiu; Zhao, Chao; Beaujuge, Pierre; Alshareef, Husam N.

2016-01-01

nanostructured ternary nickel cobalt selenides result in a much higher areal capacitance (2.33 F cm−2 at 4 mA cm−2), better rate performance and cycling stability than their binary selenide equivalents, and other ternary oxides and chalcogenides. Those hybrid

Competitive and Cooperative Effects during Nickel Adsorption to Iron Oxides in the Presence of Oxalate

Energy Technology Data Exchange (ETDEWEB)

Flynn, Elaine D. [Department of Earth and Planetary; Catalano, Jeffrey G. [Department of Earth and Planetary

2017-08-09

Iron oxides are ubiquitous in soils and sediments and play a critical role in the geochemical distribution of trace elements and heavy metals via adsorption and coprecipitation. The presence of organic acids may potentially alter how metals associate with iron oxide minerals through a series of cooperative or competitive processes: solution complexation, ternary surface complexation, and surface site competition. The macroscopic and molecular-scale effects of these processes were investigated for Ni adsorption to hematite and goethite at pH 7 in the presence of oxalate. The addition of this organic acid suppresses Ni uptake on both minerals. Aqueous speciation suggests that this is dominantly the result of oxalate complexing and solubilizing Ni. Comparison of the Ni surface coverage to the concentration of free (uncomplexed) Ni²⁺ in solution suggests that the oxalate also alters Ni adsorption affinity. EXAFS and ATR-FTIR spectroscopies indicate that these changes in binding affinity are due to the formation of Ni–oxalate ternary surface complexes. These observations demonstrate that competition between dissolved oxalate and the mineral surface for Ni overwhelms the enhancement in adsorption associated with ternary complexation. Oxalate thus largely enhances Ni mobility, thereby increasing micronutrient bioavailability and inhibiting contaminant sequestration.

A new method to estimate the atomic volume of ternary intermetallic compounds

International Nuclear Information System (INIS)

Pani, M.; Merlo, F.

2011-01-01

The atomic volume of an A x B y C z ternary intermetallic compound can be calculated starting from volumes of some proper A-B, A-C and B-C binary phases. The three methods by Colinet, Muggianu and Kohler, originally used to estimate thermodynamic quantities, and a new method here proposed, were tested to derive volume data in eight systems containing 91 ternary phases with the known structure. The comparison between experimental and calculated volume values shows the best agreement both for the Kohler method and for the new proposed procedure. -- Graphical abstract: Synopsys: the volume of a ternary intermetallic compound can be calculated starting from volumes of some binary phases, selected by the methods of Colinet, Muggianu, Kohler and a new method proposed here. The so obtained values are compared with the experimental ones for eight ternary systems. Display Omitted Research highlights: → The application of some thermodinamic methods to a crystallochemical problem. → The prevision of the average atomic volume of ternary intermetallic phases. → The proposal of a new procedure to select the proper starting set of binary phases.

First-principles study of ternary bcc alloys using special quasi-random structures

International Nuclear Information System (INIS)

Jiang Chao

2009-01-01

Using a combination of exhaustive enumeration and Monte Carlo simulated annealing, we have developed special quasi-random structures (SQSs) for ternary body-centered cubic (bcc) alloys with compositions of A 1 B 1 C 1 , A 2 B 1 C 1 , A 6 B 1 C 1 and A 2 B 3 C 3 , respectively. The structures possess local pair and multisite correlation functions that closely mimic those of the random bcc alloy. We employed the SQSs to predict the mixing enthalpies, nearest neighbor bond length distributions and electronic density of states of bcc Mo-Nb-Ta and Mo-Nb-V solid solutions. Our convergence tests indicate that even small-sized SQSs can give reliable results. Based on the SQS energetics, the predicting powers of the existing empirical ternary extrapolation models were assessed. The present results suggest that it is important to take into account the ternary interaction parameter in order to accurately describe the thermodynamic behaviors of ternary alloys. The proposed SQSs are quite general and can be applied to other ternary bcc alloys.

Diffusion Concept in Phase Stability of High Temperature Composites

National Research Council Canada - National Science Library

Zhao, Ji-Cheng

2003-01-01

A high-efficiency "diffusion multiple" approach was employed to determine the phase diagrams of nine ternary systems Nb-Ti-Si, Nb-Cr- Si, Nb-Cr-Ti, Ti-Cr-Si, Nb-Si-Al, Nb-Cr-Al, Nb-Ti-Al, Ti-Si-Al, and Ti-Cr-Al...

On hybrid cooperation in underlay cognitive radio networks

KAUST Repository

Mahmood, Nurul Huda

2013-09-01

Cooperative communication is a promising strategy to enhance the performance of a communication network as it helps to improve the coverage area and the outage performance. However, such enhancement comes at the expense of increased resource utilization, which is undesirable; more so in the case of opportunistic wireless systems such as cognitive radio networks. In order to balance the performance gains from cooperative communication against the possible over-utilization of resources, we propose and analyze an adaptive-cooperation technique for underlay cognitive radio networks, termed as hybrid-cooperation. Under the proposed cooperation scheme, secondary users in a cognitive radio network cooperate adaptively to enhance the spectral efficiency and the error performance of the network. The bit error rate, the spectral efficiency and the outage performance of the network under the proposed hybrid cooperation scheme with amplify-and-forward relaying are analyzed in this paper, and compared against conventional cooperation technique. Findings of the analytical performance analyses are further validated numerically through selected computer-based Monte-Carlo simulations. The proposed scheme is found to achieve significantly better performance in terms of the spectral efficiency and the bit error rate, compared to the conventional amplify-and-forward cooperation scheme. © 2013 IEEE.

Ternary Fission of U235 by Resonance Neutrons

International Nuclear Information System (INIS)

Kvitek, I.; Popov, Ju.P.; Rjabov, Ju.V.

1965-01-01

Recently a number of papers have appeared indicating considerable variations in the ratio of the ternary-fission cross-section to the binary-fission cross-section of U 235 on transition from one neutron resonance to another. However, such variations have not been discovered in U 233 and Pu 239 . The paper reports investigations of the ternary fission of U 235 by neutrons with an energy of 0.1 to 30 eV. Unlike other investigators of the ternary fission of U 235 , we identified the ternary-fission event by the coincidence of one of the fission fragments with a light long-range particle. This made it passible to separate ternary fissions from the possible contribution of the (n, α)reaction. The measurements were performed at the fast pulsed reactor of the Joint Institute for Nuclear Research by the time-of-flight method. A flight length of 100 m was used, giving a resolution of 0.6 μs/m. Gas scintillation counters filled with xenon at a pressure of 2 atm were used to record the fission fragments and the light long-range particle. A layer of enriched U 235 ∼2 mg/cm 2 thick and ∼300 cm 2 in area was applied to an aluminium foil 20-fim thick. The scintillations from the fission fragments were recorded in the gas volume on one side of the foil and those from the light long-range particles in that on the other. In order to assess the background (e.g . coincidences of the pulse from a fragment with that from a fission gamma quantum or a proton from the (n, p) reaction in the aluminium foil), a measurement was carried out in which the volume recording the long-range particle was shielded with a supplementary aluminium filter 1-mm thick. The results obtained indicate the absence of the considerable variations in the ratio between the ternary-and binary- fission cross-sections for U 235 that have been noted by other authors. Measurements showed no irregularity in the ratio of the cross-sections in the energy range 0.1 to 0.2 eV. The paper discusses the possible effect of

Atomic-scale properties of Ni-based FCC ternary, and quaternary alloys

International Nuclear Information System (INIS)

Tamm, Artur; Aabloo, Alvo; Klintenberg, Mattias; Stocks, Malcolm; Caro, Alfredo

2015-01-01

The aim of this study is to characterize some atomic-scale properties of Ni-based FCC multicomponent alloys. For this purpose, we use Monte Carlo method combined with density functional theory calculations to study short-range order (SRO), atomic displacements, electronic density of states, and magnetic moments in equimolar ternary NiCrCo, and quaternary NiCrCoFe alloys. According to our study, the salient features for the ternary alloy are a negative SRO parameter between Ni–Cr and a positive between Cr–Cr pairs as well as a weakly magnetic state. For the quaternary alloy we predict negative SRO parameter for Ni–Cr and Ni–Fe pairs and positive for Cr–Cr and Fe–Fe pairs. Atomic displacements for both ternary and quaternary alloys are negligible. In contrast to the ternary, the quaternary alloy shows a complex magnetic structure. The electronic structure of the ternary and quaternary alloys shows differences near the Fermi energy between a random solid solution and the predicted structure with SRO. Despite that, the calculated EXAFS spectra does not show enough contrast to discriminate between random and ordered structures. The predicted SRO has an impact on point-defect energetics, electron–phonon coupling and thermodynamic functions and thus, SRO should not be neglected when studying properties of these two alloys

An evaporation-based model of thermal neutron induced ternary fission of plutonium

International Nuclear Information System (INIS)

Lestone, J.P.

2008-01-01

Ternary fission probabilities for thermal neutron induced fission of plutonium are analyzed within the framework of an evaporation-based model where the complexity of time-varying potentials, associated with the neck collapse, are included in a simplistic fashion. If the nuclear temperature at scission and the fission-neck-collapse time are assumed to be ~ 1.2 MeV and ~ 10 -22 s, respectively, then calculated relative probabilities of ternary-fission light-charged-particle emission follow the trends seen in the experimental data. The ability of this model to reproduce ternary fission probabilities spanning seven orders of magnitude for a wide range of light-particle charges and masses implies that ternary fission is caused by the coupling of an evaporation-like process with the rapid re-arrangement of the nuclear fluid following scission. (author)

Low-temperature solid-state preparation of ternary CdS/g-C{sub 3}N{sub 4}/CuS nanocomposites for enhanced visible-light photocatalytic H{sub 2}-production activity

Energy Technology Data Exchange (ETDEWEB)

Cheng, Feiyue; Yin, Hui; Xiang, Quanjun, E-mail: xiangqj@mail.hzau.edu.cn

2017-01-01

Highlights: • CdS/g-C{sub 3}N{sub 4}/CuS composite were synthesized by low-temperature solid-state method. • CdS/g-C{sub 3}N{sub 4}/CuS show enhanced visible-light photocatalytic H{sub 2} evolution activity. • The enhanced photocatalytic H{sub 2} production activity is due to the heterojunction. • Heterojunction between the components promote charge separation/transfer property. - Abstract: Low-temperature solid-state method were gradually demonstrated as a high efficiency, energy saving and environmental protection strategy to fabricate composite semiconductor materials. CdS-based multiple composite photocatalytic materials have attracted increasing concern owning to the heterostructure constituents with tunable band gaps. In this study, the ternary CdS/g-C{sub 3}N{sub 4}/CuS composite photocatalysts were prepared by a facile and novel low-temperature solid-state strategy. The optimal ternary CdS/g-C{sub 3}N{sub 4}/CuS composite exhibits a high visible-light photocatalytic H{sub 2}-production rate of 57.56 μmol h{sup −1} with the corresponding apparent quantum efficiency reaches 16.5% at 420 nm with Na{sub 2}S/Na{sub 2}SO{sub 3} mixed aqueous solution as sacrificial agent. The ternary CdS/g-C{sub 3}N{sub 4}/CuS composites show the enhanced visible-light photocatalytic H{sub 2}-evolution activity comparing with the binary CdS-based composites or simplex CdS. The enhanced photocatalytic activity is ascribed to the heterojunctions and the synergistic effect of CuS and g-C{sub 3}N{sub 4} in promotion of the charge separation and charge mobility. This work shows that the low-temperature solid-state method is efficient and environmentally benign for the preparation of CdS-based multiple composite photocatalytic materials with enhanced visible-light photocatalytic H{sub 2}-production activity.

Description of two-proton radioactivity by the methods of the quantum theory of ternary fission

International Nuclear Information System (INIS)

Kadmenskij, S.G.

2005-01-01

Two-proton decay of spherical nuclei has been investigated on the base of the formalism of quantum mechanical theory of ternary fission. The suggested method of construction of partial two-proton-decay-width amplitudes and of asymptotics of the decaying nucleus wave functions allows to solve a problem of two-proton radioactivity description without the traditionally used in R-matrix approaches laborious sewing procedure for internal and external parent nucleus wave functions in three-body scheme. In the frame of diagonal approximation, the wave-function structure for Cooper pair of two emitted protons in parent nucleus was analyzed as well as the behavior of the wave function describing potential scattering of two-proton-decay products with taking into account decay channel coupling and properties of interaction potentials between these products [ru

Enhanced Dissolution of a Porous Carrier-Containing Ternary Amorphous Solid Dispersion System Prepared by a Hot Melt Method.

Science.gov (United States)

Hanada, Masataka; Jermain, Scott V; Williams, Robert O

2018-01-01

The focus of our study was to employ a solvent-free, thermal process to evaluate the use of a porous carrier in a drug-polymer-porous carrier ternary formulation containing a high drug load (e.g., ≥50% w/w). The purpose of the study was to improve the dissolution properties of the biopharmaceutical classification system class II drug, indomethacin, in the ternary formulation. The effect that the selected polymer has on properties of the formulation was studied, and the formulation characteristics of hypromellose (AF15), copovidone (VA64), and polyvinyl alcohol-polyethylene glycol graft copolymer was evaluated to understand differences in dissolution rates and drug adsorption onto the porous carrier. The ternary formulations were manufactured using a thermal technique that relied on heating and mixing, without the necessity of mechanical shear. All thermally processed granules that employed the porous carrier exhibited immediate release compared with crystalline indomethacin and physical mixtures. In addition, the ternary formulations maintained supersaturation compared with the binary formulations without polymer. The results of this study indicated that the thermally processed ternary formulations containing a porous carrier demonstrated a much improved dissolution profile in nonsink conditions. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Volume dependence of T/sub c/ of Ternary A-15 Phases

International Nuclear Information System (INIS)

Shamrai, V.

1984-01-01

Results are presented of measurements of the superconducting transition temperature T/sub c/, lattice constant a, magnetic susceptibility /sub chi/, and critical field H/sub c/ 2 for many Nb 3 Al and V 3 Si-based ternary phases and Nb 3 SnH/sub x/. For V 3 Si-based ternary systems and Nb 3 SnH/sub x/ the density of states at the Fermi level N(epsilon/sub F/) sharply decreases with the concentration of the alloying element. The variation of N(epsilon/sub F/) in these ternary systems cannot be explained by the variation of a. In ternary phases Nb 3 (Al/sub 1-x/dY/sub x/), where Y can be Ge, Ga, Sb, or Se, a quite clear correlation is revealed between T/sub c/ and a. The dependence of T/sub c/ on V in these systems is due to the variation of the matrix element of the electron-phonon interaction 2 >

A computer calculation of the ternary Mo-Pd-Rh phase diagram

International Nuclear Information System (INIS)

Guerler, R.; Pratt, J.N.

1993-01-01

Thermodynamic coefficients for the phases in the binary Mo-Pd, Pd-Rh and Mo-Rh systems were derived by the assessment of the available experimental data using the binary Lukas optimization program. The resulting coefficients were first successfully utilised in reestablishing the binaries. The coefficients thus obtained in the binary computation were combined with ternary descriptions to compute ternary isothermal sections. Although no ternary interaction term was involved in the construction of the isotherms, the section calculated at 1373 K is found to be consistent with the experimentally established isothermal section at the same temperature. The location of three-phase field (bcc+hcp+fcc) and phase boundaries in both isotherms are matching reasonably well. Combining only binary coefficients of these phases, it is possible to construct reasonable isothermal sections at different temperatures. Following this conclusion, isothermal sections ranging from 1373 to 2673 K of the ternary Mo-Pd-Rh system were calculated. (orig.)

Some new protonated ternary complexes of rare-earths with CDTA/DTPA and keto-glutaric acid

International Nuclear Information System (INIS)

Tripathi, S.P.; Chaturvedi, G.K.; Sharma, R.C.

1981-01-01

Potentiometric evidences have been cited for the formation of 1:1:1, M(III)-CDTA/DTPA-H 2 KGA ternary complexes in the solution equilibria (where M(III)=LA(III), Pr(III), Nd(III), Gd(III) or Dy(III); CDTA=1,2-diaminocyclohexanetetra-acetic acid; DTPA=diethylenetriaminepenta-acetic acid and H 2 KGA= β-ketoglutaric acid). Indications have been cited for the formation of protonated mixed ligand complexes at low pH as intermediate products, which undergo deprotonation at comparatively high pH forming 1:1:1, ternary species. The formation constants (log Ksub(MLL')) for the protonated ternary species, formed by simultaneous addition of both the ligands to metal ion and their deprotonation constants - log Ksub(A)sup(H) have been evaluated. The following order in the relative stabilities of the resulting complexes in terms of metal ions, La(III) < Pr(III) < Nd(III) < Gd(III) < Dy(III), has been observed. (author)

Cooperation Techniques between LTE in Unlicensed Spectrum and Wi-Fi towards Fair Spectral Efficiency.

Science.gov (United States)

Maglogiannis, Vasilis; Naudts, Dries; Shahid, Adnan; Giannoulis, Spilios; Laermans, Eric; Moerman, Ingrid

2017-08-31

On the road towards 5G, a proliferation of Heterogeneous Networks (HetNets) is expected. Sensor networks are of great importance in this new wireless era, as they allow interaction with the environment. Additionally, the establishment of the Internet of Things (IoT) has incredibly increased the number of interconnected devices and consequently the already massive wirelessly transmitted traffic. The exponential growth of wireless traffic is pushing the wireless community to investigate solutions that maximally exploit the available spectrum. Recently, 3rd Generation Partnership Project (3GPP) announced standards that permit the operation of Long Term Evolution (LTE) in the unlicensed spectrum in addition to the exclusive use of the licensed spectrum owned by a mobile operator. Alternatively, leading wireless technology developers examine standalone LTE operation in the unlicensed spectrum without any involvement of a mobile operator. In this article, we present a classification of different techniques that can be applied on co-located LTE and Wi-Fi networks. Up to today, Wi-Fi is the most widely-used wireless technology in the unlicensed spectrum. A review of the current state of the art further reveals the lack of cooperation schemes among co-located networks that can lead to more optimal usage of the available spectrum. This article fills this gap in the literature by conceptually describing different classes of cooperation between LTE and Wi-Fi. For each class, we provide a detailed presentation of possible cooperation techniques that can provide spectral efficiency in a fair manner.

Cooperative Learning in the Advanced Algebra and Trigonometry Mathematics High School Classroom

Science.gov (United States)

Jozsa, Alison

2017-01-01

Over the past three decades, researchers have found cooperative learning to have positive effects on student achievement in various subject areas and levels in education. However, there are limited studies on the impact of cooperative learning on student achievement in the area of high school mathematics. This study examined the impact of…

Ternary chalcogenide micro-pseudocapacitors for on-chip energy storage

KAUST Repository

Kurra, Narendra

2015-05-11

We report the successful fabrication of a micro-pseudocapacitor based on ternary nickel cobalt sulfide for the first time, with performance substantially exceeding that of previously reported micro-pseudocapacitors based on binary sulfides. CoNi2S4 micro-pseudocapacitor exhibits a maximum energy density of 18.7 mWh/cm3 at a power density of 1163 mW/cm3, opens up an avenue for exploring new family of ternary oxides/sulfides based micro-pseudocapacitors.

Ternary chalcogenide micro-pseudocapacitors for on-chip energy storage

KAUST Repository

Kurra, Narendra; Xia, Chuan; Hedhili, Mohamed N.; Alshareef, Husam N.

2015-01-01

We report the successful fabrication of a micro-pseudocapacitor based on ternary nickel cobalt sulfide for the first time, with performance substantially exceeding that of previously reported micro-pseudocapacitors based on binary sulfides. CoNi2S4 micro-pseudocapacitor exhibits a maximum energy density of 18.7 mWh/cm3 at a power density of 1163 mW/cm3, opens up an avenue for exploring new family of ternary oxides/sulfides based micro-pseudocapacitors.

Cooperative binding mitigates the high-dose hook effect.

Science.gov (United States)

Roy, Ranjita Dutta; Rosenmund, Christian; Stefan, Melanie I

2017-08-14

The high-dose hook effect (also called prozone effect) refers to the observation that if a multivalent protein acts as a linker between two parts of a protein complex, then increasing the amount of linker protein in the mixture does not always increase the amount of fully formed complex. On the contrary, at a high enough concentration range the amount of fully formed complex actually decreases. It has been observed that allosterically regulated proteins seem less susceptible to this effect. The aim of this study was two-fold: First, to investigate the mathematical basis of how allostery mitigates the prozone effect. And second, to explore the consequences of allostery and the high-dose hook effect using the example of calmodulin, a calcium-sensing protein that regulates the switch between long-term potentiation and long-term depression in neurons. We use a combinatorial model of a "perfect linker protein" (with infinite binding affinity) to mathematically describe the hook effect and its behaviour under allosteric conditions. We show that allosteric regulation does indeed mitigate the high-dose hook effect. We then turn to calmodulin as a real-life example of an allosteric protein. Using kinetic simulations, we show that calmodulin is indeed subject to a hook effect. We also show that this effect is stronger in the presence of the allosteric activator Ca 2+ /calmodulin-dependent kinase II (CaMKII), because it reduces the overall cooperativity of the calcium-calmodulin system. It follows that, surprisingly, there are conditions where increased amounts of allosteric activator actually decrease the activity of a protein. We show that cooperative binding can indeed act as a protective mechanism against the hook effect. This will have implications in vivo where the extent of cooperativity of a protein can be modulated, for instance, by allosteric activators or inhibitors. This can result in counterintuitive effects of decreased activity with increased concentrations of

Boron-Based Hydrogen Storage: Ternary Borides and Beyond

Energy Technology Data Exchange (ETDEWEB)

Vajo, John J. [HRL Laboratories, LLC, Malibu, CA (United States)

2016-04-28

DOE continues to seek reversible solid-state hydrogen materials with hydrogen densities of ≥11 wt% and ≥80 g/L that can deliver hydrogen and be recharged at moderate temperatures (≤100 °C) and pressures (≤100 bar) enabling incorporation into hydrogen storage systems suitable for transportation applications. Boron-based hydrogen storage materials have the potential to meet the density requirements given boron’s low atomic weight, high chemical valance, and versatile chemistry. However, the rates of hydrogen exchange in boron-based compounds are thus far much too slow for practical applications. Although contributing to the high hydrogen densities, the high valance of boron also leads to slow rates of hydrogen exchange due to extensive boron-boron atom rearrangements during hydrogen cycling. This rearrangement often leads to multiple solid phases occurring over hydrogen release and recharge cycles. These phases must nucleate and react with each other across solid-solid phase boundaries leading to energy barriers that slow the rates of hydrogen exchange. This project sought to overcome the slow rates of hydrogen exchange in boron-based hydrogen storage materials by minimizing the number of solid phases and the boron atom rearrangement over a hydrogen release and recharge cycle. Two novel approaches were explored: 1) developing matched pairs of ternary borides and mixed-metal borohydrides that could exchange hydrogen with only one hydrogenated phase (the mixed-metal borohydride) and only one dehydrogenated phase (the ternary boride); and 2) developing boranes that could release hydrogen by being lithiated using lithium hydride with no boron-boron atom rearrangement.

Ternary particles with extreme N/Z ratios from neutron-induced fission

International Nuclear Information System (INIS)

Koster, U.; Faust, H.; Friedrichs, T.; Oberstedt, S.; Fioni, G.; Grob, M.; Ahmad, I. J.; Devlin, M.; Heinz, A.; Kondev, F. G.; Lauritsen, T.; Sarantites, D. G.; Siem, S.; Sobotka, L. G.; Sonzogni, A.

2000-01-01

The existing ternary fission models can well reproduce the yields of the most abundant light charged particles. However, these models tend to significantly overestimate the yields of ternary particles with an extreme N/Z ratio: 3 He, 11 Li, 14 Be, etc. The experimental yields of these isotopes were investigated with the recoil separator LOHENGRIN down to a level of 10 -10 per fission. Results from the fissioning systems 233 U (n th , f), 235 U(n th ,f), 239 Pu(n th ,f) 241 Pu(n th ,f) and 245 Cm(n th ,f) are presented and the implications for the ternary fission models are discussed

Experimental investigation of phase equilibria in the Zr-Cu-Ni ternary system

International Nuclear Information System (INIS)

Yang, Mujin; Wang, Cuiping; Yang, Shuiyuan; Shi, Zhan; Han, Jiajia; Liu, Xingjun

2017-01-01

The phase equilibria in the Zr-Cu-Ni ternary system are investigated combined with X-ray diffraction, electron probe micro-analysis and differential scanning calorimetry. Two isothermal sections of the Zr-Cu-Ni ternary system at 1 000 C and 1 100 C are experimentally established. Most of the binary intermetallic compounds, e.g. Zr 7 Ni 10 , ZrNi, ZrNi 5 , Zr 14 Cu 51 , and Zr 2 Cu 9 , show a remarkable ternary solubility. A new ternary compound named τ 3 (Zr 31.1-30.7 . Cu 28.5-40.3 Ni 40.4-29.0 ) is detected at 1 000 C and dissolved at 1 020 C because the nearby large liquid phase field further expands. The newly determined phase equilibria will provide important information for both thermodynamic assessment and alloy design of Zr-based metallic glass.

DNA-directed self-assembly of gold nanoparticles into binary and ternary nanostructures

International Nuclear Information System (INIS)

Yao Hui; Yi Changqing; Tzang Chihung; Zhu Junjie; Yang Mengsu

2007-01-01

The assembly and characterization of gold nanoparticle-based binary and ternary structures are reported. Two strategies were used to assemble gold nanoparticles into ordered nanoscale architectures: in strategy 1, gold nanoparticles were functionalized with single-strand DNA (ssDNA) first, and then hybridized with complementary ssDNA-labelled nanoparticles to assemble designed architectures. In strategy 2, the designed architectures were constructed through hybridization between complementary ssDNA first, then by assembling gold nanoparticles to the scaffolding through gold-sulfur bonds. Both TEM measurements and agarose gel electrophoresis confirmed that the latter strategy is more efficient in generating the designed nanostructures

The symmetric MSD encoder for one-step adder of ternary optical computer

Science.gov (United States)

Kai, Song; LiPing, Yan

2016-08-01

The symmetric Modified Signed-Digit (MSD) encoding is important for achieving the one-step MSD adder of Ternary Optical Computer (TOC). The paper described the symmetric MSD encoding algorithm in detail, and developed its truth table which has nine rows and nine columns. According to the truth table, the state table was developed, and the optical-path structure and circuit-implementation scheme of the symmetric MSD encoder (SME) for one-step adder of TOC were proposed. Finally, a series of experiments were designed and performed. The observed results of the experiments showed that the scheme to implement SME was correct, feasible and efficient.

High-pressure synthesis of the first ternary melilite-type compound Sc{sub 1.67}B{sub 3}O{sub 7}

Energy Technology Data Exchange (ETDEWEB)

Schmitt, Martin K.; Huppertz, Hubert [Institut fuer Allgemeine, Anorganische und Theoretische Chemie, Universitaet Innsbruck (Austria); Ploner, Kevin [Institut fuer Physikalische Chemie, Universitaet Innsbruck (Austria); Hejny, Clivia [Institut fuer Mineralogie und Petrographie, Universitaet Innsbruck (Austria)

2017-12-13

Sc{sub 1.67}B{sub 3}O{sub 7} was synthesized in a high-pressure/high-temperature experiment at 3.5 GPa/1200 C employing a Walker-type multianvil module. The compound was characterized with X-ray diffraction and vibrational spectroscopy. It crystallizes in the tetragonal, acentric space group P42{sub 1}m (no. 113) with the lattice parameters a = 6.6597(4) and c = 4.4364(3) Aa. Sc{sub 1.67}B{sub 3}O{sub 7} is the first ternary compound adopting the melilite-type structure and therefore the simplest representative of this manifold structure family. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Simultaneous improvement in short circuit current, open circuit voltage, and fill factor of polymer solar cells through ternary strategy.

Science.gov (United States)

An, Qiaoshi; Zhang, Fujun; Li, Lingliang; Wang, Jian; Sun, Qianqian; Zhang, Jian; Tang, Weihua; Deng, Zhenbo

2015-02-18

We present a smart strategy to simultaneously increase the short circuit current (Jsc), the open circuit voltage (Voc), and the fill factor (FF) of polymer solar cells (PSCs). A two-dimensional conjugated small molecule photovoltaic material (SMPV1), as the second electron donor, was doped into the blend system of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C71-butyric acid methyl (PC71BM) to form ternary PSCs. The ternary PSCs with 5 wt % SMPV1 doping ratio in donors achieve 4.06% champion power conversion efficiency (PCE), corresponding to about 21.2% enhancement compared with the 3.35% PCE of P3HT:PC71BM-based PSCs. The underlying mechanism on performance improvement of ternary PSCs can be summarized as (i) harvesting more photons in the longer wavelength region to increase Jsc; (ii) obtaining the lower mixed highest occupied molecular orbital (HOMO) energy level by incorporating SMPV1 to increase Voc; (iii) forming the better charge carrier transport channels through the cascade energy level structure and optimizing phase separation of donor/acceptor materials to increase Jsc and FF.

Equilibrium study for ternary mixtures of biodiesel

Science.gov (United States)

Doungsri, S.; Sookkumnerd, T.; Wongkoblap, A.; Nuchitprasittichai, A.

2017-11-01

The liquid-liquid equilibrium (LLE) data for the ternary mixtures of methanol + fatty acid methyl ester (FAME) + palm oil and FAME + palm oil + glycerol at various temperatures from 35 to 55°C, the tie lines and binodial curves were also investigated and plotted in the equilibrium curve. The experimental results showed that the binodial curves of methanol + FAME + palm oil depended significantly with temperature while the binodial curves of FAME + palm oil + glycerol illustrated insignificant change with temperatures. The interaction parameters between liquid pair obtained for NRTL (Nonrandom Two-Liquid) and UNIQUAC (Universal Quasi-Chemical Theory) models from the experimental data were also investigated. It was found that the correlated parameters of UNIQUAC model for system of FAME + palm oil + glycerol, denoted as a13 and a31, were 580.42K and -123.69K, respectively, while those for system of methanol + FAME + palm oil, denoted as a42 and a24, were 71.48 K and 965.57K, respectively. The ternary LLE data reported here would be beneficial for engineers and scientists to use for prediction of yield and purity of biodiesel for the production. The UNIQUAC model agreed well with the experimental data of ternary mixtures of biodiesel.

Experimental investigation of the ternary system Ni–Pd–Sn with special focus on the B8-type phase

International Nuclear Information System (INIS)

Jandl, Isabella; Ipser, Herbert; Richter, Klaus W.

2015-01-01

The ternary alloy system Ni–Pd–Sn was investigated experimentally from 700 °C upwards, with special focus on the general NiAs-type compounds. The phase diagram and crystallographic parameters were studied by means of powder X-ray diffraction (XRD), differential thermal analysis (DTA), light optical microscopy (LOM) and scanning electron microscopy (SEM) in combination with energy dispersive X-ray spectroscopy (EDX). An isothermal section at 700 °C was constructed wherein a continuous phase field between the binary NiAs-type compounds γ (PdSn) and Ni 3 Sn 2 (high temperature modification) was detected. A series of samples throughout this phase field was used to investigate lattice parameter variations, occupation of the atomic sites and the melting behaviour. A partial ordering of the transition metals was observed. Moreover, three vertical sections at 30 at.%, 40 at.% and 50 at.% Sn were determined. Altogether, seven ternary invariant phase reactions were discovered: two ternary eutectic reactions, one ternary eutectoid reaction, three ternary transition reactions and one maximum. A complete reaction scheme for the investigated temperature range is given. Furthermore, a partial liquidus surface projection, except for the low-temperature Sn-rich region, was developed. - Highlights: • Detailed study of the ternary alloy system Ni–Pd–Sn. • 1 Isotherm, 3 vertical sections, a partial liquidus projection and a reaction scheme. • A continuous phase field, between γ and Ni 3 Sn 2 , was discovered. • Lattice parameters and structural features in this phase field were analysed. • A partial order of Ni and Pd in this phase field was observed

On Hybrid Cooperation in Underlay Cognitive Radio Networks

DEFF Research Database (Denmark)

Mahmood, Nurul Huda; Yilmaz, Ferkan; Øien, Geir E.

2013-01-01

of opportunistic wireless systems such as cognitive radio networks. In order to balance the performance gains from cooperative communication against the possible over-utilization of resources, we propose and analyze an adaptive-cooperation technique for underlay cognitive radio networks, termed as hybrid......Cooperative communication is a promising strategy to enhance the performance of a communication network as it helps to improve the coverage area and the outage performance. However, such enhancement comes at the expense of increased resource utilization, which is undesirable; more so in the case......-cooperation. Under the proposed cooperation scheme, secondary users in a cognitive radio network cooperate adaptively to enhance the spectral efficiency and the error performance of the network. The bit error rate, the spectral efficiency and the outage performance of the network under the proposed hybrid...

Maxwell-Stefan diffusion coefficient estimation for ternary systems: an ideal ternary alcohol system.

Science.gov (United States)

Allie-Ebrahim, Tariq; Zhu, Qingyu; Bräuer, Pierre; Moggridge, Geoff D; D'Agostino, Carmine

2017-06-21

The Maxwell-Stefan model is a popular diffusion model originally developed to model diffusion of gases, which can be considered thermodynamically ideal mixtures, although its application has been extended to model diffusion in non-ideal liquid mixtures as well. A drawback of the model is that it requires the Maxwell-Stefan diffusion coefficients, which are not based on measurable quantities but they have to be estimated. As a result, numerous estimation methods, such as the Darken model, have been proposed to estimate these diffusion coefficients. However, the Darken model was derived, and is only well defined, for binary systems. This model has been extended to ternary systems according to two proposed forms, one by R. Krishna and J. M. van Baten, Ind. Eng. Chem. Res., 2005, 44, 6939-6947 and the other by X. Liu, T. J. H. Vlugt and A. Bardow, Ind. Eng. Chem. Res., 2011, 50, 10350-10358. In this paper, the two forms have been analysed against the ideal ternary system of methanol/butan-1-ol/propan-1-ol and using experimental values of self-diffusion coefficients. In particular, using pulsed gradient stimulated echo nuclear magnetic resonance (PGSTE-NMR) we have measured the self-diffusion coefficients in various methanol/butan-1-ol/propan-1-ol mixtures. The experimental values of self-diffusion coefficients were then used as the input data required for the Darken model. The predictions of the two proposed multicomponent forms of this model were then compared to experimental values of mutual diffusion coefficients for the ideal alcohol ternary system. This experimental-based approach showed that the Liu's model gives better predictions compared to that of Krishna and van Baten, although it was only accurate to within 26%. Nonetheless, the multicomponent Darken model in conjunction with self-diffusion measurements from PGSTE-NMR represents an attractive method for a rapid estimation of mutual diffusion in multicomponent systems, especially when compared to exhaustive

Collective and tracer diffusion kinetics in the ternary random alloy

International Nuclear Information System (INIS)

Belova, I.V.; Murch, G.E.; Allnatt, A.R.

2002-01-01

In this study, collective and tracer diffusion kinetics is addressed for the ternary random alloy. A formal solution from the self-consistent theory of Moleko et al (Moleko L K, Allnatt A R and Allnatt E L 1989 Phil. Mag. A 59 141) is derived for collective diffusion and compared with the corresponding solution for the binary random alloy. Tracer diffusion in the ternary alloy is treated from the perspective of a special case of the quaternary random alloy. Results from Monte Carlo calculations for tracer and collective correlation factors (for the bcc ternary random alloy) are found to be in excellent agreement with this self-consistent theory but in only semi-quantitative agreement with the earlier theory of Manning (Manning J R 1971 Phys. Rev. B 4 1111). (author)

The ternary system K2SO4MgSO4CaSO4

Science.gov (United States)

Rowe, J.J.; Morey, G.W.; Silber, C.C.

1967-01-01

Melting and subsolidus relations in the system K2SO4MgSO4CaSO4 were studied using heating-cooling curves, differential thermal analysis, optics, X-ray diffraction at room and high temperatures and by quenching techniques. Previous investigators were unable to study the binary MgSO4CaSO4 system and the adjacent area in the ternary system because of the decomposition of MgSO4 and CaSO4 at high temperatures. This problem was partly overcome by a novel sealed-tube quenching method, by hydrothermal synthesis, and by long-time heating in the solidus. As a result of this study, we found: (1) a new compound, CaSO4??3MgSO4 (m.p. 1201??C) with a field extending into the ternary system; (2) a high temperature form of MgSO4 with a sluggishly reversible inversion. An X-ray diffraction pattern for this polymorphic form is given; (3) the inversion of ??-CaSO4 (anhydrite) to ??-CaSO4 at 1195??C, in agreement with grahmann; (1) (4) the melting point of MgSO4 is 1136??C and that of CaSO4 is 1462??C (using sealed tube methods to prevent decomposition of the sulphates); (5) calcium langbeinite (K2SO4??2CaSO4) is the only compound in the K2SO4CaSO4 binary system. This resolved discrepancies in the results of previous investigators; (6) a continuous solid solution series between congruently melting K2SOP4??2MgSO4 (langbeinite) and incongruently melting K2SO4??2CaSO4 (calcium langbeinite); (7) the liquidus in the ternary system consists of primary phase fields of K2SO4, MgSO4, CaSO4, langbeinite-calcium langbeinite solid solution, and CaSO4??3MgSO4. The CaSO4 field extends over a large portion of the system. Previously reported fields for the compounds (K2SO4??MgSO4??nCaSO4), K2SO4??3CaSO4 and K2SO4??CaSO4 were not found; (8) a minimum in the ternary system at: 740??C, 25% MgSO4, 6% CaSO4, 69% K2SO4; and ternary eutectics at 882??C, 49% MgSO4, 19% CaSO4, 32% K2SO4; and 880??, 67??5% MgSO4, 5% CaSO4, 27??5% K2SO4. ?? 1967.

Energy efficient cooperation in underlay RFID cognitive networks for a water smart home.

Science.gov (United States)

Nasir, Adnan; Hussain, Syed Imtiaz; Soong, Boon-Hee; Qaraqe, Khalid

2014-09-30

Shrinking water resources all over the world and increasing costs of water consumption have prompted water users and distribution companies to come up with water conserving strategies. We have proposed an energy-efficient smart water monitoring application in [1], using low power RFIDs. In the home environment, there exist many primary interferences within a room, such as cell-phones, Bluetooth devices, TV signals, cordless phones and WiFi devices. In order to reduce the interference from our proposed RFID network for these primary devices, we have proposed a cooperating underlay RFID cognitive network for our smart application on water. These underlay RFIDs should strictly adhere to the interference thresholds to work in parallel with the primary wireless devices [2]. This work is an extension of our previous ventures proposed in [2,3], and we enhanced the previous efforts by introducing a new system model and RFIDs. Our proposed scheme is mutually energy efficient and maximizes the signal-to-noise ratio (SNR) for the RFID link, while keeping the interference levels for the primary network below a certain threshold. A closed form expression for the probability density function (pdf) of the SNR at the destination reader/writer and outage probability are derived. Analytical results are verified through simulations. It is also shown that in comparison to non-cognitive selective cooperation, this scheme performs better in the low SNR region for cognitive networks. Moreover, the hidden Markov model's (HMM) multi-level variant hierarchical hidden Markov model (HHMM) approach is used for pattern recognition and event detection for the data received for this system [4]. Using this model, a feedback and decision algorithm is also developed. This approach has been applied to simulated water pressure data from RFID motes, which were embedded in metallic water pipes.

A New Class of Ternary Compound for Lithium-Ion Battery: from Composite to Solid Solution.

Science.gov (United States)

Wang, Jiali; Wu, Hailong; Cui, Yanhua; Liu, Shengzhou; Tian, Xiaoqing; Cui, Yixiu; Liu, Xiaojiang; Yang, Yin

2018-02-14

Searching for high-performance cathode materials is a crucial task to develop advanced lithium-ion batteries (LIBs) with high-energy densities for electrical vehicles (EVs). As a promising lithium-rich material, Li 2 MnO 3 delivers high capacity over 200 mAh g -1 but suffers from poor structural stability and electronic conductivity. Replacing Mn 4+ ions by relatively larger Sn 4+ ions is regarded as a possible strategy to improve structural stability and thus cycling performance of Li 2 MnO 3 material. However, large difference in ionic radii of Mn 4+ and Sn 4+ ions leads to phase separation of Li 2 MnO 3 and Li 2 SnO 3 during high-temperature synthesis. To prepare solid-solution phase of Li 2 MnO 3 -Li 2 SnO 3 , a buffer agent of Ru 4+ , whose ionic radius is in between that of Mn 4+ and Sn 4+ ions, is introduced to assist the formation of a single solid-solution phase. The results show that the Li 2 RuO 3 -Li 2 MnO 3 -Li 2 SnO 3 ternary system evolves from mixed composite phases into a single solid-solution phase with increasing Ru content. Meanwhile, discharge capacity of this ternary system shows significantly increase at the transformation point which is ascribed to the improvement of Li + /e - transportation kinetics and anionic redox chemistry for solid-solution phase. The role of Mn/Sn molar ratio of Li 2 RuO 3 -Li 2 MnO 3 -Li 2 SnO 3 ternary system has also been studied. It is revealed that higher Sn content benefits cycling stability of the system because Sn 4+ ions with larger sizes could partially block the migration of Mn 4+ and Ru 4+ from transition metal layer to Li layer, thus suppressing structural transformation of the system from layered-to-spinel phase. These findings may enable a new route for exploring ternary or even quaternary lithium-rich cathode materials for LIBs.

A new model for predicting thermodynamic properties of ternary metallic solution from binary components

International Nuclear Information System (INIS)

Fang Zheng; Zhang Quanru

2006-01-01

A model has been derived to predict thermodynamic properties of ternary metallic systems from those of its three binaries. In the model, the excess Gibbs free energies and the interaction parameter ω 123 for three components of a ternary are expressed as a simple sum of those of the three sub-binaries, and the mole fractions of the components of the ternary are identical with the sub-binaries. This model is greatly simplified compared with the current symmetrical and asymmetrical models. It is able to overcome some shortcomings of the current models, such as the arrangement of the components in the Gibbs triangle, the conversion of mole fractions between ternary and corresponding binaries, and some necessary processes for optimizing the various parameters of these models. Two ternary systems, Mg-Cu-Ni and Cd-Bi-Pb are recalculated to demonstrate the validity and precision of the present model. The calculated results on the Mg-Cu-Ni system are better than those in the literature. New parameters in the Margules equations expressing the excess Gibbs free energies of three binary systems of the Cd-Bi-Pb ternary system are also given

A Low Temperature Co-fired Ceramics Manufactured Power Inductor Based on A Ternary Hybrid Material System

Science.gov (United States)

Xie, Yunsong; Chen, Ru

Low temperature co-fired ceramics (LTCC) is one of the most important techniques to produce circuits with high working frequency, multi-functionality and high integration. We have developed a methodology to enable a ternary hybrid material system being implemented into the LTCC manufacturing process. The co-firing sintering process can be divided into a densification and cooling process. In this method, a successful ternary hybrid material densification process is achieved by tuning the sintering profile of each material to match each other. The system integrity is maintained in the cooling process is obtained by develop a strong bonding at the interfaces of each materials. As a demonstration, we have construct a power inductor device made of the ternary material system including Ag, NiCuZn ferrite and non-magnetic ceramic. The power inductors well maintains its physical integrity after sintering. The microscopic images show no obvious sign of cracks or structural deformation. More importantly, despite the bonding between the ferrite and ceramic is enhanced by non-magnetic element diffusion, the undesired magnetic elements diffusion is effectively suppressed. The electric performance shows that the power handling capability is comparable to the current state of art device.

Electronic structure of ternary hydrides based on light elements

Energy Technology Data Exchange (ETDEWEB)

Orgaz, E. [Departamento de Fisica y Quimica Teorica, Facultad de Quimica, Universidad Nacional Autonoma de Mexico, CP 04510 Coyoacan, Mexico, D.F. (Mexico)]. E-mail: orgaz@eros.pquim.unam.mx; Membrillo, A. [Departamento de Fisica y Quimica Teorica, Facultad de Quimica, Universidad Nacional Autonoma de Mexico, CP 04510 Coyoacan, Mexico, D.F. (Mexico); Castaneda, R. [Departamento de Fisica y Quimica Teorica, Facultad de Quimica, Universidad Nacional Autonoma de Mexico, CP 04510 Coyoacan, Mexico, D.F. (Mexico); Aburto, A. [Departamento de Fisica, Facultad de Ciencias, Universidad Nacional Autonoma de Mexico, CP 04510 Coyoacan, Mexico, D.F. (Mexico)

2005-12-08

Ternary hydrides based on light elements are interesting owing to the high available energy density. In this work we focused into the electronic structure of a series of known systems having the general formula AMH{sub 4}(A=Li,Na,M=B,Al). We computed the energy bands and the total and partial density of states using the linear-augmented plane waves method. In this report, we discuss the chemical bonding in this series of complex hydrides.

Public Order: Challenges of Inter-Institutional and Regional Cooperation in the Context of the Knowledge Society. A Question of Economic and Social Efficiency

Directory of Open Access Journals (Sweden)

Mariana Balan

2011-05-01

Full Text Available The context of public policies undergoes a process of rapid change due to the emergence of the dynamic knowledge-based economy and society. Public administration institutions need to adapt their material and human resources to the dynamic developments of the knowledge and information society in order to maintain efficiency and effectiveness of their scopes. One of the most fragile fields is public order and the need for improved inter-institutional cooperation at national, regional, and EU-level for achieving the objectives of ensuring citizens’ safety while safeguarding rights and liberties. The social and economic efficiency of public order policies and measures need to be reassessed and improved based on overhauled and updated inter-institutional and organisational concepts, on diversified methods of cooperation at national, regional, EU- and international level. A recent project developed in the field of public order with respect to juvenile delinquency has shown that major questions still need to be approached with respect to efficiency and effectiveness of inter-institutional cooperation with both public and private bodies, and with representatives of the non-governmental organizations. The outcomes of the project have shown that juvenile delinquency must be approached as phenomenon in the wider framework of public order, of urban and rural safety, of crime prevention and combating. One major conclusion of the project is that a new integrated model is required with respect to the intra-, and inter-institutional cooperation and dialogue, but also with respect to the skills required to work efficiently considering the challenges posed by the overall developments of a society changing towards increased knowledge and information awareness. This would allow also for improved quality assessment and effectiveness measurements based on composite process and outcome indicators for public order, and public administration, in general, as well.

Completed Local Ternary Pattern for Rotation Invariant Texture Classification

Directory of Open Access Journals (Sweden)

Taha H. Rassem

2014-01-01

Full Text Available Despite the fact that the two texture descriptors, the completed modeling of Local Binary Pattern (CLBP and the Completed Local Binary Count (CLBC, have achieved a remarkable accuracy for invariant rotation texture classification, they inherit some Local Binary Pattern (LBP drawbacks. The LBP is sensitive to noise, and different patterns of LBP may be classified into the same class that reduces its discriminating property. Although, the Local Ternary Pattern (LTP is proposed to be more robust to noise than LBP, however, the latter’s weakness may appear with the LTP as well as with LBP. In this paper, a novel completed modeling of the Local Ternary Pattern (LTP operator is proposed to overcome both LBP drawbacks, and an associated completed Local Ternary Pattern (CLTP scheme is developed for rotation invariant texture classification. The experimental results using four different texture databases show that the proposed CLTP achieved an impressive classification accuracy as compared to the CLBP and CLBC descriptors.

Using a Ternary Diagram to Display a System's Evolving Energy Distribution

Science.gov (United States)

Brazzle, Bob; Tapp, Anne

2016-01-01

A ternary diagram is a graphical representation used for systems with three components. They are familiar to mineralogists (who typically use them to categorize varieties of solid solution minerals such as feldspar) but are not yet widely used in the physics community. Last year the lead author began using ternary diagrams in his introductory…

Hierarchical Layered WS2 /Graphene-Modified CdS Nanorods for Efficient Photocatalytic Hydrogen Evolution.

Science.gov (United States)

Xiang, Quanjun; Cheng, Feiyue; Lang, Di

2016-05-10

Graphene-based ternary composite photocatalysts with genuine heterostructure constituents have attracted extensive attention in photocatalytic hydrogen evolution. Here we report a new graphene-based ternary composite consisting of CdS nanorods grown on hierarchical layered WS2 /graphene hybrid (WG) as a high-performance photocatalyst for hydrogen evolution under visible light irradiation. The optimal content of layered WG as a co-catalyst in the ternary CdS/WS2 /graphene composites was found to be 4.2 wt %, giving a visible light photocatalytic H2 -production rate of 1842 μmol h(-1)  g(-1) with an apparent quantum efficiency of 21.2 % at 420 nm. This high photocatalytic H2 -production activity is due to the deposition of CdS nanorods on layered WS2 /graphene sheets, which can efficiently suppress charge recombination, improve interfacial charge transfer, and provide reduction active sites. The proposed mechanism for the enhanced photocatalytic activity of CdS nanorods modified with hierarchical layered WG was further confirmed by transient photocurrent response. This work shows that a noble-metal-free hierarchical layered WS2 /graphene nanosheets hybrid can be used as an effective co-catalyst for photocatalytic water splitting. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Experimental determination of the phase equilibria in the Co-Fe-Zr ternary system

International Nuclear Information System (INIS)

Wang, C.P.; Yu, Y.; Zhang, H.H.; Hu, H.F.; Liu, X.J.

2011-01-01

Research highlights: → We determined four isothermal sections of the Co-Fe-Zr system from 1000 o C to 1300 o C. → No ternary compound was found in the Co-Fe-Zr ternary system. → The solubility of Fe in the liquid phase at 1300 o C is extremely large. → The (Co, Fe) 2 Zr phase form the continuous solution from Co-Zr side to Fe-Zr side. → The solubility of Zr in the fcc (Co, Fe) phase is extremely small. - Abstract: The phase equilibria in the Co-Fe-Zr ternary system were investigated by means of optical microscopy (OM), electron probe microanalysis (EPMA), X-ray diffraction (XRD), and differential scanning calorimetry (DSC) on equilibrated ternary alloys. Four isothermal sections of the Co-Fe-Zr ternary system at 1300 o C, 1200 o C, 1100 o C and 1000 o C were experimentally established. The experimental results indicate that (1) no ternary compound was found in this system; (2) the solubility of Fe in the liquid phase of the Co-rich corner at 1300 o C is extremely large; (3) the liquid phase in the Zr-rich corner and the (Co,Fe) 2 Zr phase form the continuous solid solutions from the Co-Zr side to the Fe-Zr side; (4) the solubility of Zr in the fcc (Co, Fe) phase is extremely small.

Probing the evaporation of ternary ethanol-methanol-water droplets by cavity enhanced Raman scattering.

Science.gov (United States)

Howle, Chris R; Homer, Chris J; Hopkins, Rebecca J; Reid, Jonathan P

2007-10-21

Cavity enhanced Raman scattering is used to characterise the evolving composition of ternary aerosol droplets containing methanol, ethanol and water during evaporation into a dry nitrogen atmosphere. Measurements made using non-linear stimulated Raman scattering from these ternary alcohol-water droplets allow the in situ determination of the concentration of the two alcohol components with high accuracy. The overlapping spontaneous Raman bands of the two alcohol components, arising from C-H stretching vibrational modes, are spectrally-resolved in stimulated Raman scattering measurements. We also demonstrate that the evaporation measurements are consistent with a quasi-steady state evaporation model, which can be used to interpret the evaporation dynamics occurring at a range of pressures at a particular evaporation time.

Design of thermoelectrically highly efficient Heusler compounds using phase separations and nano-composites under an economic point of view

Science.gov (United States)

Balke, Benjamin

Half-Heusler (HH) compounds are one of the most promising candidates for thermoelectric materials for automotive and industrial waste heat recovery applications. In this talk, I will give an overview about our recent investigations of phase separations in HH thermoelectrics, focusing on the ternary system TiNiSn-ZrNiSn-HfNiSn. I will show how we adapted this knowledge to design a p-type HH compound which exhibits a ZT that is increased by 130% compared to the best published bulk p-type Heusler. I will also present how we used the phase separation to design thermoelectric highly efficient nano-composites of different single-phase materials. Since the price for Hafnium doubled within the last year, our research focused on the design of HH compounds without Hafnium. I will present a very recent calculation on ZT per Euro and efficiency per Euro for various materials followed by our latest very promising results for n-type Heusler compunds without Hafnium resulting in 20 times higher ZT/Euro values. These results strongly underline the importance of phase separations as a powerful tool for designing highly efficient materials for thermoelectric applications that fulfill the industrial demands for a thermoelectric converter. The author gratefully acknowledges financial support by the thermoHEUSLER2 Project (Project No. 19U15006F) of the German Federal Ministry of Economics and Technology (BMWi).

Growth and characterization of III-N ternary thin films by plasma assisted atomic layer epitaxy at low temperatures

Energy Technology Data Exchange (ETDEWEB)

Nepal, Neeraj; Anderson, Virginia R.; Hite, Jennifer K.; Eddy, Charles R.

2015-08-31

We report the growth and characterization of III-nitride ternary thin films (Al{sub x}Ga{sub 1−x}N, In{sub x}Al{sub 1−x}N and In{sub x}Ga{sub 1−x}N) at ≤ 500 °C by plasma assisted atomic layer epitaxy (PA-ALE) over a wide stoichiometric range including the range where phase separation has been an issue for films grown by molecular beam epitaxy and metal organic chemical vapor deposition. The composition of these ternaries was intentionally varied through alterations in the cycle ratios of the III-nitride binary layers (AlN, GaN, and InN). By this digital alloy growth method, we are able to grow III-nitride ternaries by PA-ALE over nearly the entire stoichiometry range including in the spinodal decomposition region (x = 15–85%). These early efforts suggest great promise of PA-ALE at low temperatures for addressing miscibility gap challenges encountered with conventional growth methods and realizing high performance optoelectronic and electronic devices involving ternary/binary heterojunctions, which are not currently possible. - Highlights: • III-N ternaries grown at ≤ 500 °C by plasma assisted atomic layer epitaxy • Growth of InGaN and AlInN in the spinodal decomposition region (15–85%) • Epitaxial, smooth and uniform III-N film growth at low temperatures.

Growth and characterization of III-N ternary thin films by plasma assisted atomic layer epitaxy at low temperatures

International Nuclear Information System (INIS)

Nepal, Neeraj; Anderson, Virginia R.; Hite, Jennifer K.; Eddy, Charles R.

2015-01-01

We report the growth and characterization of III-nitride ternary thin films (Al x Ga 1−x N, In x Al 1−x N and In x Ga 1−x N) at ≤ 500 °C by plasma assisted atomic layer epitaxy (PA-ALE) over a wide stoichiometric range including the range where phase separation has been an issue for films grown by molecular beam epitaxy and metal organic chemical vapor deposition. The composition of these ternaries was intentionally varied through alterations in the cycle ratios of the III-nitride binary layers (AlN, GaN, and InN). By this digital alloy growth method, we are able to grow III-nitride ternaries by PA-ALE over nearly the entire stoichiometry range including in the spinodal decomposition region (x = 15–85%). These early efforts suggest great promise of PA-ALE at low temperatures for addressing miscibility gap challenges encountered with conventional growth methods and realizing high performance optoelectronic and electronic devices involving ternary/binary heterojunctions, which are not currently possible. - Highlights: • III-N ternaries grown at ≤ 500 °C by plasma assisted atomic layer epitaxy • Growth of InGaN and AlInN in the spinodal decomposition region (15–85%) • Epitaxial, smooth and uniform III-N film growth at low temperatures

Molecular designing of novel ternary copolymers of donor-acceptor polymers using genetic algorithm

International Nuclear Information System (INIS)

Arora, Vinita; Bakhshi, A.K.

2010-01-01

Graphical abstract: Alternate arrangement of donor acceptor moieties in the carbon backbone chain of an organic conjugated polymer is capable of inducing charge transfer and affects the electronic properties of the copolymer. Genetic algorithm along with simple NFC (negative factor counting) and IIM (inverse iteration method) has been used to optimize the properties of novel ternary copolymers based on polypyrrole PPy, polythiophene PTh and polyfuran PFu (as donor moieties) and containing >C=O and >C=CF 2 bridging units as acceptor moieties. - Abstract: An efficient designing route to novel ternary copolymers consisting of polypyrrole (PPy), polythiophene (PTh) and polyfuran (PFu) is developed with the help of genetic algorithm. Using the band structure results obtained from ab initio crystal orbital (CO) calculations, the electronic structures and conduction properties of real ternary copolymers based on donor acceptor type polymers are investigated. The electron rich heterocyclic rings in the backbone chain of the copolymer are joined together by electron withdrawing groups Y, carbonyl group (>C=O) and difluoromethylene group (>C=CF 2 ) in an attempt to design the conducting polymer with lowest band gap. A comparative study of various electronic properties is presented. The effects of substitution on the behaviour and properties of the copolymers as well as on the density of states (DOS) are discussed. Band gap decreases as a result of substitution on the polymer backbone chain due to decrease in ionization potential and increase in electron affinity values. This is expected to enhance the intrinsic conductivity of the resulting copolymer. Use of alternate donor acceptor moieties within the repeat units should maximize the extended π conjugation.

Molecular designing of novel ternary copolymers of donor-acceptor polymers using genetic algorithm

Energy Technology Data Exchange (ETDEWEB)

Arora, Vinita [Department of Chemistry, University of Delhi, Delhi 110 007 (India); Bakhshi, A.K., E-mail: akbakhshi2000@yahoo.com [Department of Chemistry, University of Delhi, Delhi 110 007 (India)

2010-08-03

Graphical abstract: Alternate arrangement of donor acceptor moieties in the carbon backbone chain of an organic conjugated polymer is capable of inducing charge transfer and affects the electronic properties of the copolymer. Genetic algorithm along with simple NFC (negative factor counting) and IIM (inverse iteration method) has been used to optimize the properties of novel ternary copolymers based on polypyrrole PPy, polythiophene PTh and polyfuran PFu (as donor moieties) and containing >C=O and >C=CF{sub 2} bridging units as acceptor moieties. - Abstract: An efficient designing route to novel ternary copolymers consisting of polypyrrole (PPy), polythiophene (PTh) and polyfuran (PFu) is developed with the help of genetic algorithm. Using the band structure results obtained from ab initio crystal orbital (CO) calculations, the electronic structures and conduction properties of real ternary copolymers based on donor acceptor type polymers are investigated. The electron rich heterocyclic rings in the backbone chain of the copolymer are joined together by electron withdrawing groups Y, carbonyl group (>C=O) and difluoromethylene group (>C=CF{sub 2}) in an attempt to design the conducting polymer with lowest band gap. A comparative study of various electronic properties is presented. The effects of substitution on the behaviour and properties of the copolymers as well as on the density of states (DOS) are discussed. Band gap decreases as a result of substitution on the polymer backbone chain due to decrease in ionization potential and increase in electron affinity values. This is expected to enhance the intrinsic conductivity of the resulting copolymer. Use of alternate donor acceptor moieties within the repeat units should maximize the extended {pi} conjugation.

Multicomponent ternary cocrystals of the sulfonamide group with pyridine-amides and lactams.

Science.gov (United States)

Bolla, Geetha; Nangia, Ashwini

2015-11-04

SMBA was selected as a bifunctional sulfa drug to design ternary cocrystals with pyridine amides and lactam coformers. Supramolecular assembly of five ternary cocrystals of p-sulfonamide benzoic acid with nicotinamide and 2-pyridone is demonstrated and reproducible heterosynthons are identified for crystal engineering.

Phase diagram of the ternary Zr-Ti-Sn system

International Nuclear Information System (INIS)

Arias, D.; Gonzalez Camus, M.

1987-01-01

It is well known that Ti stabilizes the high temperature cubic phase of Zr and that Sn stabilizes the low temperature hexagonal phase of Zr. The effect of Sn on the Zr-Ti diagram has been studied in the present paper. Using high purity metals, nine different alloys have been prepared, with 4-32 at % Ti, 0.7-2.2 at % Sn and Zr till 100%. Resistivity and optical and SEM metallography techniques have been employed. Effect of some impurities have been analyzed. The results are discussed and different isothermic sections of the ternary Zr-Ti-Sn diagram are presented. (Author) [es

Asymmetry in ternary fission induced by polarized neutrons and fission mechanism

International Nuclear Information System (INIS)

Bunakov, V.E.; Gennenvajn, F.; Dzhessinger, P.; Mutterer, M.; Petrov, G.A.

2003-01-01

The results of measuring the P-odd, P-even (right-left) and T-odd asymmetries of the charged particles emission in the double and ternary fission, induced by the polarized neutrons, are considered. It is shown, what kind of information on the mechanism of the ternary nuclear fission may be obtained from the theoretical analysis of these data [ru

Investigation of itraconazole ternary amorphous solid dispersions based on povidone and Carbopol.

Science.gov (United States)

Meng, Fan; Meckel, Jordan; Zhang, Feng

2017-08-30

We investigate a ternary system that consists of itraconazole (ITZ) and two polymers: povidone K12 and Carbopol 907. The interactions between these two polymers and their effects on the properties of ternary ITZ amorphous solid dispersions (ASDs) are studied. These two polymers can form a water-insoluble complex in acidic aqueous media. The critical pH is determined to be 4.17. The weight percentage of Carbopol 907 in the interpolymer complex range from 59 to 70%, depending on the initial ratios between these two polymers in the starting solutions. This complexation is driven by a negative enthalpy change from the H-bonding between the two polymers and a positive entropy change from the freed water molecules. Due to the slow precipitation of the interpolymer complex in aqueous media, the attempt to prepare ternary ASD using solvent-controlled coprecipitation is not successful. Melt extrusion is identified to be the only viable method to prepare this ternary ASD. We find that interpolymer complex-based ASDs are physically less stable and demonstrate the poorest drug-release properties when compared to individual polymer-based binary ASDs. This study illustrates that the too strong interaction between polymers in ternary ASDs is detrimental to their performance. Copyright © 2017 Elsevier B.V. All rights reserved.

Cooperation Techniques between LTE in Unlicensed Spectrum and Wi-Fi towards Fair Spectral Efficiency

Directory of Open Access Journals (Sweden)

Vasilis Maglogiannis

2017-08-01

Full Text Available On the road towards 5G, a proliferation of Heterogeneous Networks (HetNets is expected. Sensor networks are of great importance in this new wireless era, as they allow interaction with the environment. Additionally, the establishment of the Internet of Things (IoT has incredibly increased the number of interconnected devices and consequently the already massive wirelessly transmitted traffic. The exponential growth of wireless traffic is pushing the wireless community to investigate solutions that maximally exploit the available spectrum. Recently, 3rd Generation Partnership Project (3GPP announced standards that permit the operation of Long Term Evolution (LTE in the unlicensed spectrum in addition to the exclusive use of the licensed spectrum owned by a mobile operator. Alternatively, leading wireless technology developers examine standalone LTE operation in the unlicensed spectrum without any involvement of a mobile operator. In this article, we present a classification of different techniques that can be applied on co-located LTE and Wi-Fi networks. Up to today, Wi-Fi is the most widely-used wireless technology in the unlicensed spectrum. A review of the current state of the art further reveals the lack of cooperation schemes among co-located networks that can lead to more optimal usage of the available spectrum. This article fills this gap in the literature by conceptually describing different classes of cooperation between LTE and Wi-Fi. For each class, we provide a detailed presentation of possible cooperation techniques that can provide spectral efficiency in a fair manner.

ESTIMATION OF EFFICIENCY OF THE COMPETITIVE COOPERATION MODEL

Directory of Open Access Journals (Sweden)

Natalia N. Liparteliani

2014-01-01

Full Text Available Competitive cooperation model of regional travel agencies and travel market participants is considered. Evaluation of the model using mathematical and statistical methods was carried out. Relationship marketing provides a travel company certain economic advantages.

Synthesis and properties of ternary mixture of nickel/cobalt/tin oxides for supercapacitors

Science.gov (United States)

Ferreira, C. S.; Passos, R. R.; Pocrifka, L. A.

2014-12-01

The present study reports the synthesis and morphological, structural and electrochemical characterization of ternary oxides mixture containing nickel, cobalt and tin. The ternary oxide is synthesized by Pechini method with subsequent deposition onto a titanium substrate in a thin-film form. XRD and EDS analysis confirm the formation of ternary film with amorphous nature. SEM analysis show that cracks on the film favor the gain of the surface area that is an interesting feature for electrochemical capacitors. The ternary film is investigated in KOH electrolyte solution using cyclic voltammetry and charge-discharge study with a specific capacitance of 328 F g-1, and a capacitance retention of 86% over 600 cycles. The values of specific power and specific energy was 345.7 W kg-1 and 18.92 Wh kg-1, respectively.

Self-triggered coordination with ternary controllers

NARCIS (Netherlands)

De Persis, Claudio; Frasca, Paolo

2012-01-01

This paper regards coordination of networked systems with ternary controllers. We develop a hybrid coordination system which implements a self-triggered communication policy, based on polling the neighbors upon need. We prove that the proposed scheme ensures finite-time convergence to a neighborhood

Dislocation motion and high temperature plasticity of binary and ternary oxides

International Nuclear Information System (INIS)

Bretheau, T.; Castaing, J.; Rabier, J.; Veyssiere, P.

1979-01-01

Literature dealing with the plasticity of single crystal oxides deformed at elevated temperatures and the associated mobility of dislocations is reviewed. The experimental approach to the subject is examined critically by selecting oxides and deforming samples and by studying their specific mechanical behaviour, characterizing the deformation substructures and modelling the rate controlling processes. Since oxides with the simple rocksalt structure (Mg0, Ni0, Co0, Fe0,...) are not representative of all oxides, examples of other structures are also examined in detail, including Ti0 2 and Cu 2 0 oxides with fluorite (Zr0 2 , U0 2 ), with corundum (A1 2 0 3 ) and with spinel (MgA1 2 0 4 ternary) structures. Occasionally work on more exotic compounds like Y 2 0 3 or some with the garnet structure is included. (UK)

Novel siRNA delivery system using a ternary polymer complex with strong silencing effect and no cytotoxicity.

Science.gov (United States)

Kodama, Yukinobu; Shiokawa, Yumi; Nakamura, Tadahiro; Kurosaki, Tomoaki; Aki, Keisei; Nakagawa, Hiroo; Muro, Takahiro; Kitahara, Takashi; Higuchi, Norihide; Sasaki, Hitoshi

2014-01-01

We developed a novel small interfering RNA (siRNA) delivery system using a ternary complex with polyethyleneimine (PEI) and γ-polyglutamic acid (γ-PGA), which showed silencing effect and no cytotoxicity. The binary complexes of siRNA with PEI were approximately 73-102 nm in particle size and 45-52 mV in ζ-potential. The silencing effect of siRNA/PEI complexes increased with an increase of PEI, and siRNA/PEI complexes with a charge ratio greater than 16 showed significant luciferase knockdown in a mouse colon carcinoma cell line regularly expressing luciferase (Colon26/Luc cells). However, strong cytotoxicity and blood agglutination were observed in the siRNA/Lipofectamine complex and siRNA/PEI16 complex. Recharging cationic complexes with an anionic compound was reported to be a promising method for overcoming these toxicities. We therefore prepared ternary complexes of siRNA with PEI (charge ratio 16) by the addition of γ-PGA to reduce cytotoxicity and deliver siRNA. As expected, the cytotoxicity of the ternary complexes decreased with an increase of γ-PGA content, which decreased the ζ-potential of the complexes. A strong silencing effect comparable to siRNA/Lipofectamine complex was discovered in ternary complexes including γ-PGA with an anionic surface charge. The high incorporation of ternary complexes into Colon26/Luc cells was confirmed with fluorescence microcopy. Having achieved knockdown of an exogenously transfected gene, the ability of the complex to mediate knockdown of an endogenous housekeeping gene, glyceraldehyde 3-phosphate dehydrogenase (GAPDH), was assessed in B16-F10 cells. The ternary complex (siRNA/PEI16/γ-PGA12 complex) exhibited a significant GAPDH knockdown effect. Thus, we developed a useful siRNA delivery system.

Phase relationships in the Er-Mn-Ti ternary system at 773 K

International Nuclear Information System (INIS)

Liu Jingqi; Wang Xina; Tang Mengqi; Su Kunpeng; Yang Xiaomao; Li Chunhui; Li Xueqiang

2009-01-01

The Phase relationship in the Er-Mn-Ti ternary system at 773 K has been investigated by X-ray powder diffraction analysis with the aid of differential thermal analysis and optical microanalysis techniques in this work. The existence of eight binary compounds Mn 15 Ti 85, αMnTi, βMnTi, Mn 2 Ti, Mn 5 Ti, ErMn 12, Er 6 Mn 23 and ErMn 2 has been confirmed at 773 K in this system. The maximum solid solubility of Ti in Mn is about 8 at%Ti. The homogeneity range of Mn 2 Ti extends from about 31 at% to 39 at% Ti. The maximum solid solubility of Er in Mn 2 Ti phase is about less than 1 at% Er. No ternary compounds were found in this ternary system at 773K. At 773 K, the isothermal section of phase diagram of Er-Mn-Ti ternary system consists of 11 single-phase regions, 19 two-phase regions and 9 three-phase regions.

Experimental investigation of phase equilibria in the Zr-Cu-Ni ternary system

Energy Technology Data Exchange (ETDEWEB)

Yang, Mujin; Wang, Cuiping; Yang, Shuiyuan; Shi, Zhan; Han, Jiajia; Liu, Xingjun [Xiamen Univ. (China). College of Materials and Fujian Provincial Key Lab. of Materials Genome

2017-08-15

The phase equilibria in the Zr-Cu-Ni ternary system are investigated combined with X-ray diffraction, electron probe micro-analysis and differential scanning calorimetry. Two isothermal sections of the Zr-Cu-Ni ternary system at 1 000 C and 1 100 C are experimentally established. Most of the binary intermetallic compounds, e.g. Zr{sub 7}Ni{sub 10}, ZrNi, ZrNi{sub 5}, Zr{sub 14}Cu{sub 51}, and Zr{sub 2}Cu{sub 9}, show a remarkable ternary solubility. A new ternary compound named τ{sub 3} (Zr{sub 31.1-30.7} . Cu{sub 28.5-40.3}Ni{sub 40.4-29.0}) is detected at 1 000 C and dissolved at 1 020 C because the nearby large liquid phase field further expands. The newly determined phase equilibria will provide important information for both thermodynamic assessment and alloy design of Zr-based metallic glass.

Mechanochemically prepared ternary hybrid cathode material for lithium batteries

International Nuclear Information System (INIS)

Posudievsky, Oleg Yu; Kozarenko, Olga A.; Dyadyun, Vyacheslav S.; Jorgensen, Scott W.; Spearot, James A.; Koshechko, Vyacheslav G.; Pokhodenko, Vitaly D.

2013-01-01

Graphical abstract: The presence of macromolecules of an ion-conducting polymer in the composition of the ternary nanocomposite PPy–PEO/V 2 O 5 promotes interfacial transfer of lithium ions and also facilitates faster transport inside the particles of the nanocomposite. -- Highlights: • Two- and three component nanocomposites are prepared via a solvent-free mechanochemical synthesis. • The nanocomposites retain their capacity above 200 mA h g −1 for at least one hundred cycles. • The presence of PEO promotes interfacial transfer of lithium ions and facilitates faster transport inside the nanocomposite. -- Abstract: Ternary host–guest nanocomposite based on vanadium oxide and two polymers with different types of conductivity (ionic and electronic) – polypyrrole (PPy) and polyethylene oxide (PEO) – is prepared by solventless mechanochemical synthesis. The nanocomposite can be reversibly cycled with a specific capacity of ∼200 mA h g −1 for at least one hundred cycles of full charge–discharge as the active component of the positive electrode of lithium batteries. Electrochemical performance of ternary PPy 0.1 PEO 0.15 V 2 O 5 is compared with two-component analog PPy 0.1 V 2 O 5 . The presence of macromolecules of an ion-conducting polymer in the composition of the ternary nanocomposite PPy 0.1 PEO 0.15 V 2 O 5 promotes interfacial transfer of lithium ions and also facilitates faster transport inside the particles of the nanocomposite

Improving power conversion efficiency of perovskite solar cells by cooperative LSPR of gold-silver dual nanoparticles

Institute of Scientific and Technical Information of China (English)

Peng Liu; Cong-hua Zhou; Bing-chu Yang; Gang Liu; Run-sheng Wu; Chu-jun Zhang; Fang Wan; Shui-gen Li; Jun-liang Yang; Yong-li Gao

2017-01-01

Enhancing optical and electrical performances is effective in improving power conversion efficiency of photovoltaic devices.Here,gold and silver dual nanoparticles were imported and embedded in the hole transport layer of perovskite solar cells.Due to the cooperative localized surface plasmon resonance of these two kinds of metal nanostructures,light harvest of perovskite material layer and the electrical performance of device were improved,which finally upgraded short circuit current density by 10.0％,and helped to increase power conversion efficiency from 10.4％ to 11.6％ under AM 1.5G illumination with intensity of 100 mW/cm2.In addition,we explored the influence of silver and gold nanoparticles on charge carrier generation,dissociation,recombination,and transportation inside perovskite solar cells.

Affine planes, ternary rings, and examples of non-Desarguesian planes

OpenAIRE

Ivanov, Nikolai V.

2016-01-01

The paper is devoted to a detailed self-contained exposition of a part of the theory of affine planes leading to a construction of affine (or, equivalently, projective) planes not satisfying the Desarques axiom. It is intended to complement the introductory expositions of the theory of affine and projective planes. A novelty of our exposition is a new notation for the ternary operation in a ternary ring, much more suggestive than the standard one.

Mechanism of ternary breakup in the reaction 197Au+197Au at 15A MeV

International Nuclear Information System (INIS)

Tian Junlong; Wu Xizhen; Li Zhuxia; Zhao Kai; Zhang Yingxun; Li Xian; Yan Shiwei

2010-01-01

The mechanism of the ternary breakup of the very heavy system 197 Au+ 197 Au at an energy of 15A MeV has been studied by using the improved quantum molecular dynamics model. The calculation results reproduce the characteristic features in ternary breakup events explored in a series of experiments; i.e., the masses of three fragments are comparable in size and the very fast, nearly collinear breakup of the colliding system is dominant in the ternary breakup events. Further, the evolution of the time scales of different ternary reaction modes and the behavior of mass distributions of three fragments with impact parameters are studied. The time evolution of the configurations of the composite reaction systems is also studied. We find that for most of the ternary breakup events with the features found in the experiments, the configuration of the composite system has two-preformed-neck shape. The study shows that those ternary breakup events having the characteristic features found in the experiments happen at relatively small impact parameter reactions, but not at peripheral reactions. The ternary breakup reaction at peripheral reactions belongs to binary breakup with a neck emission.

Design and implementation of the modified signed digit multiplication routine on a ternary optical computer.

Science.gov (United States)

Xu, Qun; Wang, Xianchao; Xu, Chao

2017-06-01

Multiplication with traditional electronic computers is faced with a low calculating accuracy and a long computation time delay. To overcome these problems, the modified signed digit (MSD) multiplication routine is established based on the MSD system and the carry-free adder. Also, its parallel algorithm and optimization techniques are studied in detail. With the help of a ternary optical computer's characteristics, the structured data processor is designed especially for the multiplication routine. Several ternary optical operators are constructed to perform M transformations and summations in parallel, which has accelerated the iterative process of multiplication. In particular, the routine allocates data bits of the ternary optical processor based on digits of multiplication input, so the accuracy of the calculation results can always satisfy the users. Finally, the routine is verified by simulation experiments, and the results are in full compliance with the expectations. Compared with an electronic computer, the MSD multiplication routine is not only good at dealing with large-value data and high-precision arithmetic, but also maintains lower power consumption and fewer calculating delays.

Partially fluorinated aarylene polyethers and their ternary blends with PBI and H3PO4

DEFF Research Database (Denmark)

Li, Qingfeng; Jensen, Jens Oluf; Pan, Chao

2008-01-01

Ternary blend membranes based on sulphonated partially fluorinated arylene polyether, polybenzimidazole (PBI) and phosphoric acid were prepared and characterised as electrolyte for high temperature proton exchange membrane fuel cells. Partially fluorinated arylene polyether was first prepared from...

Evaluation of the efficiency of continuous wavelet transform as processing and preprocessing algorithm for resolution of overlapped signals in univariate and multivariate regression analyses; an application to ternary and quaternary mixtures

Science.gov (United States)

Hegazy, Maha A.; Lotfy, Hayam M.; Mowaka, Shereen; Mohamed, Ekram Hany

2016-07-01

Wavelets have been adapted for a vast number of signal-processing applications due to the amount of information that can be extracted from a signal. In this work, a comparative study on the efficiency of continuous wavelet transform (CWT) as a signal processing tool in univariate regression and a pre-processing tool in multivariate analysis using partial least square (CWT-PLS) was conducted. These were applied to complex spectral signals of ternary and quaternary mixtures. CWT-PLS method succeeded in the simultaneous determination of a quaternary mixture of drotaverine (DRO), caffeine (CAF), paracetamol (PAR) and p-aminophenol (PAP, the major impurity of paracetamol). While, the univariate CWT failed to simultaneously determine the quaternary mixture components and was able to determine only PAR and PAP, the ternary mixtures of DRO, CAF, and PAR and CAF, PAR, and PAP. During the calculations of CWT, different wavelet families were tested. The univariate CWT method was validated according to the ICH guidelines. While for the development of the CWT-PLS model a calibration set was prepared by means of an orthogonal experimental design and their absorption spectra were recorded and processed by CWT. The CWT-PLS model was constructed by regression between the wavelet coefficients and concentration matrices and validation was performed by both cross validation and external validation sets. Both methods were successfully applied for determination of the studied drugs in pharmaceutical formulations.

Ternary particles with extreme N/Z ratios from neutron-induced fission

Energy Technology Data Exchange (ETDEWEB)

Koster, U.; Faust, H.; Friedrichs, T.; Oberstedt, S.; Fioni, G.; Grob, M.; Ahmad, I. J.; Devlin, M.; Heinz, A.; Kondev, F. G.; Lauritsen, T.; Sarantites, D. G.; Siem, S.; Sobotka, L. G.; Sonzogni, A.

2000-05-16

The existing ternary fission models can well reproduce the yields of the most abundant light charged particles. However, these models tend to significantly overestimate the yields of ternary particles with an extreme N/Z ratio: {sup 3}He, {sup 11}Li, {sup 14}Be, etc. The experimental yields of these isotopes were investigated with the recoil separator LOHENGRIN down to a level of 10{sup {minus}10} per fission. Results from the fissioning systems {sup 233}U (n{sub th}, f), {sup 235}U(n{sub th},f), {sup 239}Pu(n{sub th},f) {sup 241}Pu(n{sub th},f) and {sup 245}Cm(n{sub th},f) are presented and the implications for the ternary fission models are discussed.

Exploitative and hierarchical antagonism in a cooperative bacterium.

Directory of Open Access Journals (Sweden)

Francesca Fiegna

2005-11-01

Full Text Available Social organisms that cooperate with some members of their own species, such as close relatives, may fail to cooperate with other genotypes of the same species. Such noncooperation may take the form of outright antagonism or social exploitation. Myxococcus xanthus is a highly social prokaryote that cooperatively develops into spore-bearing, multicellular fruiting bodies in response to starvation. Here we have characterized the nature of social interactions among nine developmentally proficient strains of M. xanthus isolated from spatially distant locations. Strains were competed against one another in all possible pairwise combinations during starvation-induced development. In most pairings, at least one competitor exhibited strong antagonism toward its partner and a majority of mixes showed bidirectional antagonism that decreased total spore production, even to the point of driving whole populations to extinction. Differential response to mixing was the primary determinant of competitive superiority rather than the sporulation efficiencies of unmixed populations. In some competitive pairings, the dominant partner sporulated more efficiently in mixed populations than in clonal isolation. This finding represents a novel form of exploitation in bacteria carried out by socially competent genotypes and is the first documentation of social exploitation among natural bacterial isolates. Patterns of antagonistic superiority among these strains form a highly linear dominance hierarchy. At least some competition pairs construct chimeric, rather than segregated, fruiting bodies. The cooperative prokaryote M. xanthus has diverged into a large number of distinct social types that cooperate with clone-mates but exhibit intense antagonism toward distinct social types of the same species. Most lengthy migration events in nature may thus result in strong antagonism between migratory and resident populations, and this antagonism may have large effects on local

Hierarchical Mesoporous Zinc-Nickel-Cobalt Ternary Oxide Nanowire Arrays on Nickel Foam as High-Performance Electrodes for Supercapacitors.

Science.gov (United States)

Wu, Chun; Cai, Junjie; Zhang, Qiaobao; Zhou, Xiang; Zhu, Ying; Shen, Pei Kang; Zhang, Kaili

2015-12-09

Nickel foam supported hierarchical mesoporous Zn-Ni-Co ternary oxide (ZNCO) nanowire arrays are synthesized by a simple two-step approach including a hydrothermal method and subsequent calcination process and directly utilized for supercapacitive investigation for the first time. The nickel foam supported hierarchical mesoporous ZNCO nanowire arrays possess an ultrahigh specific capacitance value of 2481.8 F g(-1) at 1 A g(-1) and excellent rate capability of about 91.9% capacitance retention at 5 A g(-1). More importantly, an asymmetric supercapacitor with a high energy density (35.6 Wh kg(-1)) and remarkable cycle stability performance (94% capacitance retention over 3000 cycles) is assembled successfully by employing the ZNCO electrode as positive electrode and activated carbon as negative electrode. The remarkable electrochemical behaviors demonstrate that the nickel foam supported hierarchical mesoporous ZNCO nanowire array electrodes are highly desirable for application as advanced supercapacitor electrodes.

Motivation, Coordination and Cognition in Cooperatives

NARCIS (Netherlands)

L. Feng (Li)

2010-01-01

textabstractA cooperative is a firm collectively owned by many independent input suppliers or buyers. This dissertation examines the nature of a cooperative and its efficiency compared with other governance structures from the perspectives of motivation, coordination and cognition. We find that the

Experimental and predicted refractive index properties in ternary mixtures of associated liquids

International Nuclear Information System (INIS)

Sechenyh, Vitaliy V.; Legros, Jean-Claude; Shevtsova, Valentina

2011-01-01

Highlights: → Measurements of refractive indices of 200 different aqueous ternary mixtures have been performed for two wave lengths. → Refractive indices of the associated ternary mixtures can be modeled with a relative error of about 0.9. → Difference between experimental and calculated derivatives of refractive index with concentration is unsatisfactory large. - Abstract: Refractive indices of ternary mixtures formed by (water + ethanol + k-ethylene glycol) (when k is mono, di or tri) and (water + t-butanol + dimethyl sulfoxide) are presented over a wide range of mixture compositions. All measurements have been conducted at 298.15 K and atmospheric pressure using two light sources: one in the visible (λ = 670 nm) and the other in the infrared (λ = 925 nm) spectrum. The performance of several mixing rules that are commonly used in modeling optical constants are examined. We demonstrate that the refractive indices of the associated ternary mixtures can be modeled with a relative error of about 0.9% by using the thermodynamical properties of the pure components. The concentration derivatives of the refractive index are an important parameter, as they are required for different experimental techniques. These derivatives have been determined from the experimental data on refractive indices. However, applying mixing rules for calculation of the derivatives of the refractive indices with respect to concentrations does not provide satisfactory results in the case of ternary mixtures of associated liquids.

Ternary CNTs@TiO₂/CoO Nanotube Composites: Improved Anode Materials for High Performance Lithium Ion Batteries.

Science.gov (United States)

Madian, Mahmoud; Ummethala, Raghunandan; Naga, Ahmed Osama Abo El; Ismail, Nahla; Rümmeli, Mark Hermann; Eychmüller, Alexander; Giebeler, Lars

2017-06-20

TiO₂ nanotubes (NTs) synthesized by electrochemical anodization are discussed as very promising anodes for lithium ion batteries, owing to their high structural stability, high surface area, safety, and low production cost. However, their poor electronic conductivity and low Li⁺ ion diffusivity are the main drawbacks that prevent them from achieving high electrochemical performance. Herein, we report the fabrication of a novel ternary carbon nanotubes (CNTs)@TiO₂/CoO nanotubes composite by a two-step synthesis method. The preparation includes an initial anodic fabrication of well-ordered TiO₂/CoO NTs from a Ti-Co alloy, followed by growing of CNTs horizontally on the top of the oxide films using a simple spray pyrolysis technique. The unique 1D structure of such a hybrid nanostructure with the inclusion of CNTs demonstrates significantly enhanced areal capacity and rate performances compared to pure TiO₂ and TiO₂/CoO NTs, without CNTs tested under identical conditions. The findings reveal that CNTs provide a highly conductive network that improves Li⁺ ion diffusivity, promoting a strongly favored lithium insertion into the TiO₂/CoO NT framework, and hence resulting in high capacity and an extremely reproducible high rate capability.

Cooperative driving in platooning scenario’s

NARCIS (Netherlands)

van der Linden, M.J.G.M.; Nijmeijer, H.

2011-01-01

Cooperative driving enables a more efficient use of existing infrastructure which reduces the expenditures and land use for new roads. Cooperative driving is based on intelligent communication between vehicles and between vehicles and their environment. Vehicles can drive closer to each other due to

Synthesis and characterization of (Ni{sub 1−x}Co{sub x})Se{sub 2} based ternary selenides as electrocatalyst for triiodide reduction in dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Theerthagiri, J.; Senthil, R.A. [Solar Energy Lab, Department of Chemistry, Thiruvalluvar University, Vellore 632115 (India); Buraidah, M.H. [Centre for Ionics University of Malaya, Department of Physics, University of Malaya, Kuala Lumpur 50603 (Malaysia); Raghavender, M. [Department of Physics, Yogi Vemana University, Kadapa 516003, Andhra Pradesh (India); Madhavan, J., E-mail: jagan.madhavan@gmail.com [Solar Energy Lab, Department of Chemistry, Thiruvalluvar University, Vellore 632115 (India); Arof, A.K. [Centre for Ionics University of Malaya, Department of Physics, University of Malaya, Kuala Lumpur 50603 (Malaysia)

2016-06-15

Ternary metal selenides of (Ni{sub 1−x}Co{sub x})Se{sub 2} with 0≤x≤1 were synthesized by using one-step hydrothermal reduction route. The synthesized metal selenides were utilized as an efficient, low-cost platinum free counter electrode for dye-sensitized solar cells. The cyclic voltammetry and electrochemical impedance spectroscopy studies revealed that the Ni{sub 0.5}Co{sub 0.5}Se{sub 2} counter electrode exhibited higher electrocatalytic activity and lower charge transfer resistance at the counter electrode/electrolyte interface than the other compositions for reduction of triiodide to iodide. Ternary selenides of Ni{sub 0.5}Co{sub 0.5}Se{sub 2} offer a synergistic effect to the electrocatalytic activity for the reduction of triiodide that might be due to an increase in active catalytic sites and small charge transfer resistance. The DSSC with Ni{sub 0.5}Co{sub 0.5}Se{sub 2} counter electrode achieved a high power conversion efficiency of 6.02%, which is comparable with that of conventional platinum counter electrode (6.11%). This present investigation demonstrates the potential application of Ni{sub 0.5}Co{sub 0.5}Se{sub 2} as counter electrode in dye-sensitized solar cells.

A Power-Optimized Cooperative MAC Protocol for Lifetime Extension in Wireless Sensor Networks.

Science.gov (United States)

Liu, Kai; Wu, Shan; Huang, Bo; Liu, Feng; Xu, Zhen

2016-10-01

In wireless sensor networks, in order to satisfy the requirement of long working time of energy-limited nodes, we need to design an energy-efficient and lifetime-extended medium access control (MAC) protocol. In this paper, a node cooperation mechanism that one or multiple nodes with higher channel gain and sufficient residual energy help a sender relay its data packets to its recipient is employed to achieve this objective. We first propose a transmission power optimization algorithm to prolong network lifetime by optimizing the transmission powers of the sender and its cooperative nodes to maximize their minimum residual energy after their data packet transmissions. Based on it, we propose a corresponding power-optimized cooperative MAC protocol. A cooperative node contention mechanism is designed to ensure that the sender can effectively select a group of cooperative nodes with the lowest energy consumption and the best channel quality for cooperative transmissions, thus further improving the energy efficiency. Simulation results show that compared to typical MAC protocol with direct transmissions and energy-efficient cooperative MAC protocol, the proposed cooperative MAC protocol can efficiently improve the energy efficiency and extend the network lifetime.

Developing Low-Clinker Ternary Blends for Indian Cement Industry

Science.gov (United States)

Pal, Aritra

2018-05-01

In today's scenario cement-concrete has become the backbone of infrastructure development. The use of concrete is increasing day by day and so does cement. One of the major concerns is that the cement manufacturing contributes 7% of total man-made CO2 emission in the environment. At the same time India being a developing country secured the second position in cement production. On the other hand solid waste management is one of the growing problems in India. As we are one of the major contributors in this situation so, the time has come to think about the sustainable alternatives. From various researches it has been observed that the low clinker cement can be suitable option. In the present paper we have tried to develop a low clinker ternary blend for Indian cement industry using the concept of synergetic behavior of fly ash-limestone reaction and formation of more stable monocarboaluminate hydrate and hemicarboaluminate hydrate. 30% fly ash and 15% limestone and 5% gypsum have been used as supplementary cementing material for replacing 50% clinker. The mechanical properties like, compressive strength, have been studied for the fly ash limestone ternary blends cements and the results have been compared with the other controlled blends and ternary blends. The effect of intergrinding of constituent materials has shown a comparable properties which can be used for various structural application. The effect of dolomitic limestone has also been studied in fly ash limestone ternary blends and the result shows the relation between compressive strength and dolomite content is inversely proportional.

Segregation in ternary alloys: an interplay of driving forces

International Nuclear Information System (INIS)

Luyten, J.; Helfensteyn, S.; Creemers, C.

2003-01-01

Monte Carlo (MC) simulations combined with the constant bond energy (CBE) model are set up to explore and understand the general segregation behaviour in ternary alloys as a function of composition and more in particular the segregation to Cu-Ni-Al (1 0 0) surfaces. Besides its simplicity, allowing swift simulations, which are necessary for a first general survey over all possible compositions, one of the advantages of the CBE model lies in the possibility to clearly identify the different driving forces for segregation. All simulations are performed in the Grand Canonical Ensemble, using a new algorithm to determine the chemical potential of the components. Notwithstanding the simplicity of the CBE model, one extra feature is evidenced: depending on the values of the interatomic interaction parameters, in some regions of the ternary diagram, a single solid solution becomes thermodynamically unstable, leading to demixing into two conjugate phases. The simulations are first done for three hypothetical systems that are however representative for real alloy systems. The three systems are characterised by different sets of interatomic interaction parameters. These extensive simulations over the entire composition range of the ternary alloy yield a 'topographical' segregation map, showing distinct regions where different species segregate. These distinct domains originate from a variable interplay between the driving forces for segregation and attractive/repulsive interactions in the bulk of the alloy. The results on these hypothetical systems are very helpful for a better understanding of the segregation behaviour in Cu-Ni-Al and other ternary alloys

Ternary fission in an effective liquid drop model

International Nuclear Information System (INIS)

Duarte, Sergio B.; Tavares, Odilon A.P.; Dimarco, A.; Goncalves, Marcello; Guzman, Fernando; Trallero-Herrera, Carlos; Rodriguez, Oscar; Garcia, Fermin

2001-01-01

Full text follows: The nuclear partition in three fragments has been observed in recent experiments for fission process of 252 Cf and 24 '0 Pu. We apply the Effective Liquid Drop Model (ELDM), successfully used for discussing binary cold fission and cluster emissions for a three center geometric shape parametrization, describing the quasi-molecular deformation which can lead to ternary fragmentation. A preliminary calculation for rates of these processes are performed and the results are compared to the rate of the dominant binary fission process. A large range of parent nuclei (spherical and deformed) is covered in the calculation. The purpose is to point out others possible ternary fission process experimentally measurable. (author)

Dynamical theory of subconstituents based on ternary algebras

International Nuclear Information System (INIS)

Bars, I.; Guenaydin, M.

1980-01-01

We propose a dynamical theory of possible fundamental constituents of matter. Our scheme is based on (super) ternary algebras which are building blocks of Lie (super) algebras. Elementary fields, called ''ternons,'' are associated with the elements of a (super) ternary algebra. Effective gauge bosons, ''quarks,'' and ''leptons'' are constructed as composite fields from ternons. We propose two- and four-dimensional (super) ternon theories whose structures are closely related to CP/sub N/ and Yang-Mills theories and their supersymmetric extensions. We conjecture that at large distances (low energies) the ternon theories dynamically produce effective gauge theories and thus may be capable of explaining the present particle-physics phenomenology. Such a scenario is valid in two dimensions

Thermodynamic calculations in ternary titanium–aluminium–manganese system

Directory of Open Access Journals (Sweden)

ANA I. KOSTOV

2008-04-01

Full Text Available Thermodynamic calculations in the ternary Ti–Al–Mn system are shown in this paper. The thermodynamic calculations were performed using the FactSage thermochemical software and database, with the aim of determining thermodynamic properties, such as activities, coefficient of activities, partial and integral values of the enthalpies and Gibbs energies of mixing and excess energies at two different temperatures: 2000 and 2100 K. Bearing in mind that no experimental data for the Ti–Al–Mn ternary system have been obtained or reported. The obtained results represent a good base for further thermodynamic analysis and may be useful as a comparison with some future critical experimental results and thermodynamic optimization of this system.

Cohesion energy calculations for ternary ionic novel crystals

International Nuclear Information System (INIS)

Vazquez P, G.; Cabrera, E.; Mijangos, R.R.; Valdez, E.; Duarte, C.

2001-01-01

The present work calculates the value of the link energy of a crystalline ternary structure newly formed by alkali halides. The ternary structure prepared with different concentrations of KCl x KBrRbCl 2 maintains a very good miscibility and stability. The calculation is based on the use of a generalization of the Vegard law (which generally is valid for binary compounds) for calculating the values of the lattice constant and the repulsive m exponent. The value of the lattice parameter given by X-ray diffractometry agrees with the close approximation of the calculated value of the method used. It also compares the value of energy cohesion obtained by the Born expression with more complex approximations. (Author)

Highly toughened polypropylene/ethylene–propylene-diene monomer/zinc dimethacrylate ternary blends prepared via peroxide-induced dynamic vulcanization

Energy Technology Data Exchange (ETDEWEB)

Chen, Yukun, E-mail: cyk@scut.edu.cn [The Key Laboratory of Polymer Processing Engineering, Ministry of Education, South China University of Technology, Guangzhou 510640 (China); School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640 (China); Xu, Chuanhui [College of Material Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Cao, Liming [The Key Laboratory of Polymer Processing Engineering, Ministry of Education, South China University of Technology, Guangzhou 510640 (China); School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640 (China); Cao, Xiaodong [College of Material Science and Engineering, South China University of Technology, Guangzhou 510640 (China)

2013-02-15

Polypropylene (PP)/ethylene–propylene-diene monomer (EPDM)/zinc dimethacrylate (ZDMA) blends with remarkable toughness and extensibility were successfully prepared via peroxide dynamical vulcanization. A unique structure with the EPDM particles surrounded by a transition zone containing numerous polymerized ZDMA (PZDMA) nano-particles was observed for the first time by using transmission electron microscopy (TEM) examination, which contributed to the dramatically increase of Izod impact strength. Dynamic mechanical analysis (DMA) confirmed that the possible PZDMA graft products resulted from peroxide dynamical vulcanization improved the compatibility between EPDM and PP phases. The specific morphology of the PP/EPDM/ZDMA blends indicated that ZDMA can lead to size reduction and good distribution uniformity of the crosslinked rubber particles and the increase of adhesion between PP matrix and EPDM phases during deformation. The synergic effect of the increase in the effective volume of the EPDM phase, the improved compatibility and adhesion between EPDM and PP phases and the deformation of those fine rubber particles is believed to result in the remarkable high toughness and extensibility of the PP/EPDM/ZDMA blends. Particularly for the PP/EPDM ratio of 70/30, the PP/EPDM/ZDMA (70/30/9, w/w/w) ternary blends with the Izod impact strength nearly 2 times higher than PP/EPDM (70/30, w/w) binary blends and 15–20 times higher than PP are achieved; besides, the elongation at break of PP/EPDM/ZDMA ternary blends is 4–5 times higher than that of PP/EPDM binary blends. - Highlights: ► ZDMA largely toughen peroxide dynamically vulcanized PP/EPDM blend. ► PZDMA graft products improved the compatibility and adhesion between EPDM and PP. ► Size reduction and good distribution uniformity of crosslinked rubber particles.

Highly toughened polypropylene/ethylene–propylene-diene monomer/zinc dimethacrylate ternary blends prepared via peroxide-induced dynamic vulcanization

International Nuclear Information System (INIS)

Chen, Yukun; Xu, Chuanhui; Cao, Liming; Cao, Xiaodong

2013-01-01

Polypropylene (PP)/ethylene–propylene-diene monomer (EPDM)/zinc dimethacrylate (ZDMA) blends with remarkable toughness and extensibility were successfully prepared via peroxide dynamical vulcanization. A unique structure with the EPDM particles surrounded by a transition zone containing numerous polymerized ZDMA (PZDMA) nano-particles was observed for the first time by using transmission electron microscopy (TEM) examination, which contributed to the dramatically increase of Izod impact strength. Dynamic mechanical analysis (DMA) confirmed that the possible PZDMA graft products resulted from peroxide dynamical vulcanization improved the compatibility between EPDM and PP phases. The specific morphology of the PP/EPDM/ZDMA blends indicated that ZDMA can lead to size reduction and good distribution uniformity of the crosslinked rubber particles and the increase of adhesion between PP matrix and EPDM phases during deformation. The synergic effect of the increase in the effective volume of the EPDM phase, the improved compatibility and adhesion between EPDM and PP phases and the deformation of those fine rubber particles is believed to result in the remarkable high toughness and extensibility of the PP/EPDM/ZDMA blends. Particularly for the PP/EPDM ratio of 70/30, the PP/EPDM/ZDMA (70/30/9, w/w/w) ternary blends with the Izod impact strength nearly 2 times higher than PP/EPDM (70/30, w/w) binary blends and 15–20 times higher than PP are achieved; besides, the elongation at break of PP/EPDM/ZDMA ternary blends is 4–5 times higher than that of PP/EPDM binary blends. - Highlights: ► ZDMA largely toughen peroxide dynamically vulcanized PP/EPDM blend. ► PZDMA graft products improved the compatibility and adhesion between EPDM and PP. ► Size reduction and good distribution uniformity of crosslinked rubber particles

Experimental investigation of phase equilibria in the Cu–Ni–Si ternary system

Energy Technology Data Exchange (ETDEWEB)

Liu, Xingjun; Xiang, Shulin; Yang, Shuiyuan; Shi, Rongpei; Wang, Cuiping, E-mail: wangcp@xmu.edu.cn

2013-11-25

Highlights: •Three isothermal sections of the Cu–Ni–Si system have been investigated. •The ternary compound τ{sub 1} and the liquid phase are confirmed at 1073 K. •The γ (Cu{sub 5}Si) and θ (Ni{sub 2}Si) phases can be stabilized at higher or lower temperatures. -- Abstract: The phase equilibria in the Cu–Ni–Si ternary system have been investigated experimentally by means of electron probe microanalysis (EPMA), X-ray diffraction (XRD) and differential scanning calorimetry (DSC) analysis on equilibrated ternary alloys. Three isothermal sections at 1073, 1173 and 1273 K are determined in the whole composition range. The existence of liquid phase and the ternary compound τ{sub 1} is confirmed at 1073 K. The binary γ (Cu{sub 5}Si), γ (Ni{sub 31}Si{sub 12}), δ (Ni{sub 2}Si) and θ (Ni{sub 2}Si) phases exhibit a considerable solubility of a third element. In addition, the γ (Cu{sub 5}Si) and θ (Ni{sub 2}Si) phases can be stabilized by the addition of Ni and Cu, respectively.

Ternary Hollow Mesoporous TiN/N-Graphene/Pt Hybrid Results in Enhanced Electrocatalytic Performance for Methanol Oxidation and Oxygen Reduction Reaction

International Nuclear Information System (INIS)

Liu, Baocang; Huo, Lili; Zhang, Geng; Zhang, Jun

2016-01-01

Highlights: • A novel hollow mesoporous ternary @M-TiN/N-G/Pt electrocatalysts were synthesized. • The @M-TiN/N-G/Pt electrocatalysts displayed outstanding activity and stability toward MOR and ORR. • The activity and stability of @M-TiN/N-G/Pt electrocatalysts were higher than Pt/TiN, @M-TiN/Pt, and Pt/C catalysts. • The excellent electrocatalytic performance rooted in its unique configuration. • Several reasons were proposed to explain the enhanced electrocatalytic performance of @M-TiN/N-G/Pt. - Abstract: A novel hollow mesoporous TiN/N-graphene (N-G) hybrid architecture (@M-TiN/N-G) composed of N-doped graphene wrapped mesoporous TiN nanoparticle shells was constructed for the first time. It can be used as an efficient support for creating a highly efficient ternary @M-TiN/N-G/Pt electrocatalyst with superior catalytic activity and stability for methanol oxidation reaction (MOR) and oxygen reduction reaction (ORR) through decorating well-dispersed Pt nanoparticles on @M-TiN/N-G surface. By optimizing the content of N-G in catalysts, the @M-TiN/N-G/Pt catalysts display superior catalytic activity and stability toward MOR and ORR to traditional Pt/C and graphene-free Pt/TiN and @M-TiN/Pt catalysts. The various characterization results reveal that the outstanding electrocatalytic performance of @M-TiN/N-G/Pt catalyst roots in its large surface area, high porosity, strong interaction among Pt, TiN, and N-G, excellent electron transfer property facilitated by N-doped graphene, and small size of Pt and TiN nanocrystals. The synthetic approach may be available for constructing other graphene based hollow metal nitrides, carbides, and phosphides for various electrocatalytic applications.

Synthesis and properties of Ag/ZnO/g-C3N4 ternary micro/nano composites by microwave-assisted method

Science.gov (United States)

Zhang, Zijie; Li, Xuexue; Chen, Haitao; Shao, Gang; Zhang, Rui; Lu, Hongxia

2018-01-01

Ag/ZnO/g-C3N4 ternary micro/nanocomposites, as novel visible-light-driven photocatalysts, were prepared by a simple and convenient microwave-assisted method. The resulting ternary structure micro/nano composites were characterized by x-ray diffraction, x-ray photoelectron spectroscopy, scanning electron microscopy, ultraviolet-visible diffuse reflectance spectroscopy and infrared radiation techniques to examine its phase structure, valence state, morphological, thermal and optical properties. Well crystallized Ag/ZnO/g-C3N4 ternary micro/nano composites were synthesized under microwave-radiation for 15 min with the output of 240 W. Further experiments indicated Ag(5.0mol%)/ZnO/g-C3N4 photocatalyst in degradation of methylene blue exhibited an outstanding photocatalytic activity and its reaction rate constant (k, 0.0084 min-1) is 7.5, 2.4 2.9 and 3.5 times higher than that of monolithic ZnO (k, 0.0011 min-1), ZnO/g-C3N4(k, 0.0035 min-1), Ag(5 mol%)/ZnO(k, 0.0029 min-1) and Ag(5mol%)/g-C3N4 (k, 0.0024 min-1) respectively. Finally, a possible photocatalytic mechanism of Ag/ZnO/g-C3N4 photocatalyst in degradation process was proposed. This work provides a feasible strategy to synthesize an efficient ZnO-based photocatalyst which combines structure and properties of different dimensional components and made this ternary system an exciting candidate for sunlight-driven photocatalytic water treatment.

Operating Cooperatively (OC sensor for highly specific recognition of nucleic acids.

Directory of Open Access Journals (Sweden)

Evan M Cornett

Full Text Available Molecular Beacon (MB probes have been extensively used for nucleic acid analysis because of their ability to produce fluorescent signal in solution instantly after hybridization. The indirect binding of MB probe to a target analyte offers several advantages, including: improved genotyping accuracy and the possibility to analyse folded nucleic acids. Here we report on a new design for MB-based sensor, called 'Operating Cooperatively' (OC, which takes advantage of indirect binding of MB probe to a target analyte. The sensor consists of two unmodified DNA strands, which hybridize to a universal MB probe and a nucleic acid analyte to form a fluorescent complex. OC sensors were designed to analyze two human SNPs and E. coli 16S rRNA. High specificity of the approach was demonstrated by the detection of true analyte in over 100 times excess amount of single base substituted analytes. Taking into account the flexibility in the design and the simplicity in optimization, we conclude that OC sensors may become versatile and efficient tools for instant DNA and RNA analysis in homogeneous solution.

International cooperation in highly technological fields, especially in the field of aeronautics and astronautics and nuclear engineering

International Nuclear Information System (INIS)

Schunk, G.

1982-01-01

The subject of the study is the analysis of Research and Development (RandD) cooperation in highly technological fields. The study deals in particular with the reasons for cooperation, the aims and types of cooperation, with cooperating partners, as well as with alternative solutions and possible future developments. Special attention is given to those factors, which necessitate cooperation, and to aspects of possible alternatives and future developments. (orig.) [de

HIGH-PRESSURE VAPOR-LIQUID EQUILIBRIUM DATA FOR BINARY AND TERNARY SYSTEMS FORMED BY SUPERCRITICAL CO2, LIMONENE AND LINALOOL

Directory of Open Access Journals (Sweden)

MELO S. A. B. VIEIRA DE

1999-01-01

Full Text Available The feasibility of deterpenating orange peel oil with supercritical CO2 depends on relevant vapor-liquid equilibrium data because the selectivity of this solvent for limonene and linalool (the two key components of the oil is of crucial importance. The vapor-liquid equilibrium data of the CO2-limonene binary system was measured at 50, 60 and 70oC and pressures up to 10 MPa, and of the CO2-linalool binary system at 50oC and pressures up to 85 bar. These results were compared with published data when available in the literature. The unpublished ternary phase equilibrium of CO2-limonene-linalool was studied at 50oC and up to 9 MPa. Selectivities obtained using these ternary data were compared with those calculated using binary data and indicate that a selective separation of limonene and linalool can be achieved.

Energy Efficient Cooperation in Underlay RFID Cognitive Networks for a Water Smart Home

Directory of Open Access Journals (Sweden)

Adnan Nasir

2014-09-01

Full Text Available Shrinking water  resources all over the world and increasing  costs of water consumption  have prompted  water users  and distribution companies  to come up with water conserving strategies. We have proposed an energy-efficient  smart water monitoring application in [1], using low power RFIDs. In the home environment,  there exist many primary interferences within a room, such as cell-phones,  Bluetooth  devices, TV signals, cordless phones and WiFi devices.  In order to reduce the interference  from our proposed RFID network for these primary  devices, we have proposed a cooperating  underlay  RFID cognitive network for our smart application on water.  These underlay  RFIDs should strictly adhere to the interference thresholds to work in parallel with the primary wireless devices [2].  This work is an extension of our previous  ventures proposed in [2,3], and we enhanced the previous efforts by introducing  a new system model and RFIDs.  Our proposed scheme is mutually energy efficient and maximizes the signal-to-noise ratio (SNR for the RFID link, while keeping the interference levels for the primary  network below a certain threshold. A closed form expression for the probability density function (pdf of the SNR at the destination reader/writer and outage probability are derived. Analytical results are verified through simulations. It is also shown that in comparison to non-cognitive selective cooperation,  this scheme performs  better in the low SNR region for cognitive networks. Moreover, the hidden Markov model’s (HMM multi-level variant hierarchical hidden Markov model (HHMM approach is used for pattern recognition and event detection for the data received for this system [4]. Using this model, a feedback and decision algorithm is also developed.  This approach has been applied  to simulated water pressure data from RFID motes, which were embedded in metallic water pipes.

Possible Mechanisms of Ternary Fission in the 197Au+197 Au System at 15 AMeV

International Nuclear Information System (INIS)

Jun-Long, Tian; Xian, Li; Shi-Wei, Yan; Xi-Zhen, Wu; Zhu-Xia, Li

2009-01-01

Ternary fission in 197 Au+ 197 Au collisions at 15 A MeV is investigated by using the improved quantum molecular dynamical (ImQMD) model. The experimental mass distributions for each of the three fragments are reproduced for the first time without any freely adjusting parameters. The mechanisms of ternary fission in central and semi-central collisions are dynamically studied. In direct prolate ternary fission, two necks are found to be formed almost simultaneously and rupture sequentially in a very short time interval. Direct oblate ternary fission is a very rare fission event, in which three necks are formed and rupture simultaneously, forming three equally sized fragments along space-symmetric directions in the reaction plane. In sequential ternary fission a binary division is followed by another binary fission event after hundreds of fm/c. (nuclear physics)

Deciphering the Sox-Oct partner code by quantitative cooperativity measurements.

Science.gov (United States)

Ng, Calista K L; Li, Noel X; Chee, Sheena; Prabhakar, Shyam; Kolatkar, Prasanna R; Jauch, Ralf

2012-06-01

Several Sox-Oct transcription factor (TF) combinations have been shown to cooperate on diverse enhancers to determine cell fates. Here, we developed a method to quantify biochemically the Sox-Oct cooperation and assessed the pairing of the high-mobility group (HMG) domains of 11 Sox TFs with Oct4 on a series of composite DNA elements. This way, we clustered Sox proteins according to their dimerization preferences illustrating that Sox HMG domains evolved different propensities to cooperate with Oct4. Sox2, Sox14, Sox21 and Sox15 strongly cooperate on the canonical element but compete with Oct4 on a recently discovered compressed element. Sry also cooperates on the canonical element but binds additively to the compressed element. In contrast, Sox17 and Sox4 cooperate more strongly on the compressed than on the canonical element. Sox5 and Sox18 show some cooperation on both elements, whereas Sox8 and Sox9 compete on both elements. Testing rationally mutated Sox proteins combined with structural modeling highlights critical amino acids for differential Sox-Oct4 partnerships and demonstrates that the cooperativity correlates with the efficiency in producing induced pluripotent stem cells. Our results suggest selective Sox-Oct partnerships in genome regulation and provide a toolset to study protein cooperation on DNA.

Ternary Pt/Rh/SnO2 electrocatalysts for oxidizing ethanol to CO2.

Science.gov (United States)

Kowal, A; Li, M; Shao, M; Sasaki, K; Vukmirovic, M B; Zhang, J; Marinkovic, N S; Liu, P; Frenkel, A I; Adzic, R R

2009-04-01

Ethanol, with its high energy density, likely production from renewable sources and ease of storage and transportation, is almost the ideal combustible for fuel cells wherein its chemical energy can be converted directly into electrical energy. However, commercialization of direct ethanol fuel cells has been impeded by ethanol's slow, inefficient oxidation even at the best electrocatalysts. We synthesized a ternary PtRhSnO(2)/C electrocatalyst by depositing platinum and rhodium atoms on carbon-supported tin dioxide nanoparticles that is capable of oxidizing ethanol with high efficiency and holds great promise for resolving the impediments to developing practical direct ethanol fuel cells. This electrocatalyst effectively splits the C-C bond in ethanol at room temperature in acid solutions, facilitating its oxidation at low potentials to CO(2), which has not been achieved with existing catalysts. Our experiments and density functional theory calculations indicate that the electrocatalyst's activity is due to the specific property of each of its constituents, induced by their interactions. These findings help explain the high activity of Pt-Ru for methanol oxidation and the lack of it for ethanol oxidation, and point to the way to accomplishing the C-C bond splitting in other catalytic processes.

Ternary Blends of High Aluminate Cement, Fly ash and Blast-furnace slag for Sewerage Lining Mortar

Science.gov (United States)

Chao, L. C.; Kuo, C. P.

2018-01-01

High aluminate cement (HAC), fly ash (FA) and blast-furnace slag (BFS) have been treated sustainable materials for the use of cement products for wastewater infrastructure due to their capabilities of corrosion resistance. The purpose of this study is to optimize a ternary blend of above mentioned materials for a special type of mortar for sewerage lining. By the using of Taguchi method, four control parameters including water/cementitious material ratio, mix water content, fly ash content and blast-furnace slag content were considered in nine trial mix designs in this study. By evaluating target properties including (1) maximization of compressive strength, (2) maximization of electricity resistance and (3) minimization of water absorption rate, the best possible levels for each control parameter were determined and the optimal mix proportions were verified. Through the implementation of the study, a practical and completed idea for designing corrosion resistive mortar comprising HAC, FA and BSF is provided.

Synthesis and sonocatalytic performance of a ternary magnetic MIL-101(Cr)/RGO/ZnFe2O4 nanocomposite for degradation of dye pollutants.

Science.gov (United States)

Nirumand, Ladan; Farhadi, Saeed; Zabardasti, Abedin; Khataee, Alireza

2018-04-01

In this study, new ternary magnetic MIL-101(Cr)/RGO/ZnFe 2 O 4 catalyst (with 30% wt of ZnFe 2 O 4 ) was synthesized via a hydrothermal route for sonodegradation of organic dyes. The structural, optical and magnetic properties of the nanocomposite were detected by means of X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), UV-visible spectroscopy (UV-visible), field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX) spectroscopy, vibrating sample magnetometer (VSM), atomic force microscopy (AFM), Raman spectroscopy and BET surface area analysis. To evaluate the sonocatalytic activity of the as-prepared MIL-101(Cr)/RGO/ZnFe 2 O 4 nanocomposite, the H 2 O 2 -assisted degradation of organic dyes such as congo red (CR), methylene blue (MB), Rhodamine B (RhB) and methyl orange (MO) in aqueous solution was studied under ultrasound irradiation. The obtained results indicated that the ternary MIL-101(Cr)/RGO/ZnFe 2 O 4 nanocomposite had better performance for sonodegradation of these dyes than MIL-101(Cr)/RGO, pure MIL-101(Cr) or ZnFe 2 O 4 . The enhanced sonocatalytic performance of the as-prepared ternary nanocomposite could be attributed to the fast generation and separation of charge carriers (electrons and holes) in ZnFe 2 O 4 and MIL-101(Cr) and their transfer to the surface of graphene sheets. Moreover, the relatively high specific surface area of the MIL-101(Cr)/rGO and magnetic property of ZnFe 2 O 4 improve the degradation efficiency of the dyes. The recovery of the ternary magnetic sonocatalyst from treated water could be easily achieved using an external magnetic field. The main influence factors on the sonocatalytic activity such as catalyst dosage and dye initial concentration were also investigated. The trapping experiments indicated that OH radicals are the prominent active species in dye degradation. In addition, the reusability test, was also carried out to ensure the stability of the employed sonocatalyst

Highly photoluminescent europium tetraphenylimidodiphosphinate ternary complexes with heteroaromatic co-ligands. Solution and solid state studies

Energy Technology Data Exchange (ETDEWEB)

Pietraszkiewicz, Marek, E-mail: mpietraszkiewicz@ichf.edu.pl [Institute of Physical Chemistry, Polish Academy of Sciences, Kasprzaka 44/52, 01-224 Warsaw (Poland); Pietraszkiewicz, Oksana; Karpiuk, Jerzy; Majka, Alina [Institute of Physical Chemistry, Polish Academy of Sciences, Kasprzaka 44/52, 01-224 Warsaw (Poland); Dutkiewicz, Grzegorz; Borowiak, Teresa [Adam Mickiewicz University, Faculty of Chemistry, Department of Crystallography, Grunwaldzka 6, 60-780 Poznań (Poland); Kaczmarek, Anna M. [L3–Luminescent Lanthanide Lab, f-element coordination chemistry, Ghent University, Department of Inorganic and Physical Chemistry, Krijgslaan 281, Building S3, 9000 Gent (Belgium); Van Deun, Rik, E-mail: rik.vandeun@ugent.be [L3–Luminescent Lanthanide Lab, f-element coordination chemistry, Ghent University, Department of Inorganic and Physical Chemistry, Krijgslaan 281, Building S3, 9000 Gent (Belgium)

2016-02-15

Tetraphenylimidodiphosphinate (tpip) forms neutral 3:1 complexes with lanthanide ions. These complexes can accommodate one ancillary planar heterocyclic ligand to complement their coordination sphere of Eu{sup 3+} to coordination number 8. Several co-ligands were tested to form new complexes: 1,10-phenanthroline, bathophenanthroline, 2,4,6-tris(2-pyridyl)-1,3,5-triazine, dipyrido[3,2-f:2′,3′-h]quinoxaline and 2,2′:6′,2′′-terpyridine. The addition of heterocyclic N,N-bidentate co-ligands to the coordination sphere results in a dramatic (by a factor of 45–50) luminescence enhancement of the parent Eu(tpip){sub 3}. The solid-state measurements confirmed that the ancillary ligands strongly increased the photoluminescence quantum yield (PLQY) of the investigated complexes. - Highlights: • We have disovered highly photoluminescent ternary Eu(III) complexes. • They consist of Eu(III) tetraphenylimidodiphosphinate, and planar heterocyclic ligands. • The increase in photoluminescence quantum yields in solution is enhanced up to 50 times in solution. • The solid-state photoluminescence exceeds 80% at room temperature.

Highly photoluminescent europium tetraphenylimidodiphosphinate ternary complexes with heteroaromatic co-ligands. Solution and solid state studies

International Nuclear Information System (INIS)

Pietraszkiewicz, Marek; Pietraszkiewicz, Oksana; Karpiuk, Jerzy; Majka, Alina; Dutkiewicz, Grzegorz; Borowiak, Teresa; Kaczmarek, Anna M.; Van Deun, Rik

2016-01-01

Tetraphenylimidodiphosphinate (tpip) forms neutral 3:1 complexes with lanthanide ions. These complexes can accommodate one ancillary planar heterocyclic ligand to complement their coordination sphere of Eu 3+ to coordination number 8. Several co-ligands were tested to form new complexes: 1,10-phenanthroline, bathophenanthroline, 2,4,6-tris(2-pyridyl)-1,3,5-triazine, dipyrido[3,2-f:2′,3′-h]quinoxaline and 2,2′:6′,2′′-terpyridine. The addition of heterocyclic N,N-bidentate co-ligands to the coordination sphere results in a dramatic (by a factor of 45–50) luminescence enhancement of the parent Eu(tpip) 3 . The solid-state measurements confirmed that the ancillary ligands strongly increased the photoluminescence quantum yield (PLQY) of the investigated complexes. - Highlights: • We have disovered highly photoluminescent ternary Eu(III) complexes. • They consist of Eu(III) tetraphenylimidodiphosphinate, and planar heterocyclic ligands. • The increase in photoluminescence quantum yields in solution is enhanced up to 50 times in solution. • The solid-state photoluminescence exceeds 80% at room temperature.

Refractive indices of ternary liquid mixtures containing aliphatic alcohols at several temperatures

Directory of Open Access Journals (Sweden)

Sovilj Milan N.

2005-01-01

Full Text Available The refractive indices of ternary liquid mixtures (2-propanol+2-butanol+ethanol and (chloroform+2-propanol+2-butanol were measured at 20, 25, 30, and 35°C, and atmospheric pressure. The results were used to calculate the refractive index deviations over the entire mole fraction range for the mixtures. The refractive index deviations for the ternary mixtures were further fitted to empirical correlations (Cibulka Nagata-Tamura, and Lopez et al to estimate the ternary fitting parameters. Standard deviations and average percentage deviations from the regression lines are shown. The best fit was obtained by the Nagata-Tamura empirical correlation. Some of the existing predictive equations for the refractive index deviations (Tsao-Smith, Köhler, and Colinet were tested.

Fe-Cr-V ternary alloy-based ferritic steels for high- and low-temperature applications

International Nuclear Information System (INIS)

Rieth, M.; Materna-Morris, E.; Dudarev, S.L.; Boutard, J.-L.; Keppler, H.; Mayor, J.

2009-01-01

The phase stability of alloys and steels developed for application in nuclear fission and fusion technology is one of the decisive factors determining the potential range of operating temperatures and radiation conditions that the core elements of a power plant can tolerate. In the case of ferritic and ferritic-martensitic steels, the choice of the chemical composition is dictated by the phase diagram for binary FeCr alloys where in the 0-9% range of Cr composition the alloy remains in the solid solution phase at and below the room temperature. For Cr concentrations exceeding 9% the steels operating at relatively low temperatures are therefore expected to exhibit the formation of α' Cr-rich precipitates. These precipitates form obstacles for the propagation of dislocations, impeding plastic deformation and embrittling the material. This sets the low temperature limit for the use of of high (14% to 20%) Cr steels, which for the 20% Cr steels is at approximately 600 deg. C. On the other hand, steels containing 12% or less Cr cannot be used at temperatures exceeding ∼600 deg. C due to the occurrence of the α-γ transition (912 deg. C in pure iron and 830 deg. C in 7% Cr alloy), which weakens the steel in the high temperature limit. In this study, we investigate the physical properties of a concentrated ternary alloy system that attracted relatively little attention so far. The phase diagram of ternary Fe-Cr-V alloy shows no phase boundaries within a certain broad range of Cr and V concentrations. This makes the alloy sufficiently resistant to corrosion and suggests that steels and dispersion strengthened materials based on this alloy composition may have better strength and stability at high temperatures. Experimental heats were produced on a laboratory scale by arc melting the material components to pellets, then by melting the pellets in an induction furnace and casting the melt into copper moulds. The compositions in weight percent (iron base) are 10Cr5V, 10Cr

A Cross-Layer Optimization Approach for Energy Efficient Wireless Sensor Networks: Coalition-Aided Data Aggregation, Cooperative Communication, and Energy Balancing