CIGS thin films, solar cells, and submodules fabricated using a rf-plasma cracked Se-radical beam source

International Nuclear Information System (INIS)

Ishizuka, Shogo; Yamada, Akimasa; Shibata, Hajime; Fons, Paul; Niki, Shigeru

2011-01-01

Coevaporated Cu(In,Ga)Se 2 (CIGS) film growth using a rf-plasma cracked Se-radical beam (R-Se) source leads to a significant reduction in the amount of raw Se source material wasted during growth and exhibits unique film properties such as highly dense, smooth surfaces and large grain size. R-Se grown CIGS solar cells also show concomitant unique properties different from conventional evaporative Se (E-Se) source grown CIGS cells. In the present work, the impact of modified surfaces, interfaces, and bulk crystal properties of R-Se grown CIGS films on the solar cell performance was studied. When a R-Se source was used, Na diffusion into CIGS layers was enhanced while a remarkable diffusion of elemental Ga and Se into Mo back contact layers was observed. Improvements in the bulk crystal quality as manifested by large grain size and increased Na concentration with the use of a R-Se source is expected to be effective to improve photovoltaic performance. Using a R-Se source for the growth of CIGS absorber layers at a relatively low growth temperature, we have successfully demonstrated a monolithically integrated submodule efficiency of 15.0% (17 cells, aperture area of 76.5 cm 2 ) on 0.25-mm thick soda-lime glass substrates.

Expanding Thermal Plasma Chemical Vapour Deposition of ZnO:Al Layers for CIGS Solar Cells

Directory of Open Access Journals (Sweden)

K. Sharma

2014-01-01

Full Text Available Aluminium-doped zinc oxide (ZnO:Al grown by expanding thermal plasma chemical vapour deposition (ETP-CVD has demonstrated excellent electrical and optical properties, which make it an attractive candidate as a transparent conductive oxide for photovoltaic applications. However, when depositing ZnO:Al on CIGS solar cell stacks, one should be aware that high substrate temperature processing (i.e., >200°C can damage the crucial underlying layers/interfaces (such as CIGS/CdS and CdS/i-ZnO. In this paper, the potential of adopting ETP-CVD ZnO:Al in CIGS solar cells is assessed: the effect of substrate temperature during film deposition on both the electrical properties of the ZnO:Al and the eventual performance of the CIGS solar cells was investigated. For ZnO:Al films grown using the high thermal budget (HTB condition, lower resistivities, ρ, were achievable (~5 × 10−4 Ω·cm than those grown using the low thermal budget (LTB conditions (~2 × 10−3 Ω·cm, whereas higher CIGS conversion efficiencies were obtained for the LTB condition (up to 10.9% than for the HTB condition (up to 9.0%. Whereas such temperature-dependence of CIGS device parameters has previously been linked with chemical migration between individual layers, we demonstrate that in this case it is primarily attributed to the prevalence of shunt currents.

Numerical modelling of CIGS/CdS solar cell

Science.gov (United States)

Devi, Nisha; Aziz, Anver; Datta, Shouvik

2018-05-01

In this work, we design and analyze the Cu(In,Ga)Se2 (CIGS) solar cell using simulation software "Solar Cell Capacitance Simulator in One Dimension (SCAPS-1D)". The conventional CIGS solar cell uses various layers, like intrinsic ZnO/Aluminium doped ZnO as transparent oxide, antireflection layer MgF2, and electron back reflection (EBR) layer at CIGS/Mo interface for good power conversion efficiency. We replace this conventional model by a simple model which is easy to fabricate and also reduces the cost of this cell because of use of lesser materials. The new designed model of CIGS solar cell is ITO/CIGS/OVC/CdS/Metal contact, where OVC is ordered vacancy compound. From this simple structure, even at very low illumination we are getting good results. We simulate this CIGS solar cell model by varying various physical parameters of CIGS like thickness, carrier density, band gap and temperature.

Optical Metrology for CIGS Solar Cell Manufacturing and its Cost Implications

Science.gov (United States)

Sunkoju, Sravan Kumar

Solar energy is a promising source of renewable energy which can meet the demand for clean energy in near future with advances in research in the field of photovoltaics and cost reduction by commercialization. Availability of a non-contact, in-line, real time robust process control strategies can greatly aid in reducing the gap between cell and module efficiencies, thereby leading to cost-effective large-scale manufacturing of high efficiency CIGS solar cells. In order to achieve proper process monitoring and control for the deposition of the functional layers of CuIn1-xGaxSe 2 (CIGS) based thin film solar cell, optical techniques such as spectroscopic reflectometry and polarimetry are advantageous because they can be set up in an unobtrusive manner in the manufacturing line, and collect data in-line and in-situ. The use of these techniques requires accurate optical models that correctly represent the properties of the layers being deposited. In this study, Spectroscopic ellipsometry (SE) has been applied for the characterization of each individual stage of CIGS layers deposited using the 3-stage co-evaporation process along with the other functional layers. Dielectric functions have been determined for the energy range from 0.7 eV to 5.1 eV. Critical-point line-shape analysis was used in this study to determine the critical point energies of the CIGS based layers. To control the compositional and thickness uniformity of all the functional layers during the fabrication of CIGS solar cells over large areas, multilayer photovoltaics (PV) stack optical models were developed with the help of extracted dielectric functions. In this study, mapping capability of RC2 spectroscopic ellipsometer was used to map all the functional layer thicknesses of a CIGS solar cell in order to probe the spatial non-uniformities that can affect the performance of a cell. The optical functions for each of the stages of CIGS 3-stage deposition process along with buffer layer and transparent

TEMPERATUREEFFECT OFELECTRICALPROPERTIES OF CIGS SOLAR CELL

Directory of Open Access Journals (Sweden)

A. M. Ferouani

2015-07-01

Full Text Available In this paper we are interested in studying the copper–indium–gallium–selenium (CIGS solar cells sandwiched between cadmium sulfide (CdS and ZnO as buffer layers, and Molybdenum (Mo. Thus, we report our simulation results using the capacitance simulator (SCAPS in terms of layer thickness, absorber layer band gap and operating temperature to find out the optimum choice. An efficiency of 20.61% (with Voc of 635.2mV, Jsc of 44.08 mA/cm2 and fill factor of 0.73 has been achieved with CdS used as buffer layer as the reference case. It is also found that the high efficiency CIGS cells with the low temperature were a very high efficiency conversion.

CIGS Solar Cells for Space Applications: Numerical Simulation of the Effect of Traps Created by High-Energy Electron and Proton Irradiation on the Performance of Solar Cells

Science.gov (United States)

Dabbabi, Samar; Ben Nasr, Tarek; Turki Kamoun, Najoua

2018-02-01

Numerical simulation is carried out using the Silvaco ATLAS software to predict the effect of 1-MeV electron and 4-MeV proton irradiation on the performance of a Cu(In, Ga)Se2 (CIGS) solar cell that operates under the air mass zero spectrum (AM0). As a consequence of irradiation, two types of traps are induced including the donor- and acceptor-type traps. Only one of them (the donor-type trap) is found responsible for the degradation of the open-circuit voltage (V OC), fill factor (FF) and efficiency (η), while the short circuit current (J SC) remains essentially unaffected. The modelling simulation validity is verified by comparison with the experimental data. This article shows that CIGS solar cells are suited for space applications.

The influence of Na on metastable defect kinetics in CIGS materials

International Nuclear Information System (INIS)

Erslev, Peter T.; Lee, Jin Woo; Shafarman, William N.; Cohen, J. David

2009-01-01

The electronic properties of matched pairs of Cu(In x Ga 1-x )Se 2 (CIGS) solar cells, with and without normal sodium levels, were studied by junction capacitance methods including admittance spectroscopy, drive level capacitance profiling (DLCP) and transient photocapacitance spectroscopy (TPC). The capacitance profiling measurements revealed a large deep defect density in the vicinity of the barrier interface that was likely responsible for the lower performance of the reduced Na samples. The metastable properties of CIGS solar cells were also examined, and these revealed marked differences between the two types of samples. These results directly address the predictions of theoretical microscopic models that have been proposed to account for metastable effects in CIGS

Band gap engineering of tandem structured CIGS compound absorption layer fabricated by sputtering and selenization

International Nuclear Information System (INIS)

Kang, San; Sharma, Rahul; Sim, Jae-Kwan; Lee, Cheul-Ro

2013-01-01

. In the tandem CIGS layer, consist of CIS/CIGS, CIS/CGS, and CIS/CIGS/CGS thin films, the band gap was further increased from 1.42 to 2.06 eV, respectively. Such band gap engineering in CIGS tandem absorption layer will be a stepping stone to further improve the solar cell performance

Band gap engineering of tandem structured CIGS compound absorption layer fabricated by sputtering and selenization

Energy Technology Data Exchange (ETDEWEB)

Kang, San; Sharma, Rahul; Sim, Jae-Kwan [Semiconductor Materials Processing Laboratory, School of Advanced Materials Engineering, College of Engineering, Research Center for Advanced Materials Development (RCAMD), Chonbuk National University, Deokjin-dong 664-14, Jeonju 561-756 (Korea, Republic of); Lee, Cheul-Ro, E-mail: crlee7@jbnu.ac.kr [Semiconductor Materials Processing Laboratory, School of Advanced Materials Engineering, College of Engineering, Research Center for Advanced Materials Development (RCAMD), Chonbuk National University, Deokjin-dong 664-14, Jeonju 561-756 (Korea, Republic of)

2013-06-25

, and CGS thin films. In the tandem CIGS layer, consist of CIS/CIGS, CIS/CGS, and CIS/CIGS/CGS thin films, the band gap was further increased from 1.42 to 2.06 eV, respectively. Such band gap engineering in CIGS tandem absorption layer will be a stepping stone to further improve the solar cell performance.

Solution-deposited CIGS thin films for ultra-low-cost photovoltaics

Science.gov (United States)

Eldada, Louay A.; Hersh, Peter; Stanbery, Billy J.

2010-09-01

We describe the production of photovoltaic modules with high-quality large-grain copper indium gallium selenide (CIGS) thin films obtained with the unique combination of low-cost ink-based precursors and a reactive transfer printing method. The proprietary metal-organic inks contain a variety of soluble Cu-, In- and Ga- multinary selenide materials; they are called metal-organic decomposition (MOD) precursors, as they are designed to decompose into the desired precursors. Reactive transfer is a two-stage process that produces CIGS through the chemical reaction between two separate precursor films, one deposited on the substrate and the other on a printing plate in the first stage. In the second stage, these precursors are rapidly reacted together under pressure in the presence of heat. The use of two independent thin films provides the benefits of independent composition and flexible deposition technique optimization, and eliminates pre-reaction prior to the synthesis of CIGS. In a few minutes, the process produces high quality CIGS films, with large grains on the order of several microns, and preferred crystallographic orientation, as confirmed by compositional and structural analysis by XRF, SIMS, SEM and XRD. Cell efficiencies of 14% and module efficiencies of 12% were achieved using this method. The atmospheric deposition processes include slot die extrusion coating, ultrasonic atomization spraying, pneumatic atomization spraying, inkjet printing, direct writing, and screen printing, and provide low capital equipment cost, low thermal budget, and high throughput.

Photovoltaic manufacturing cost and throughput improvements for thin-film CIGS-based modules: Phase 1 technical report, July 1998--July 1999

Energy Technology Data Exchange (ETDEWEB)

Wiedeman, S.; Wendt, R.G.

2000-03-01

The primary objectives of the Global Solar Energy (GSE) Photovoltaic Manufacturing Technology (PVMaT) subcontract are directed toward reducing cost and expanding the production rate of thin-film CuInGaSe{sub 2} (CIGS)-based PV modules on flexible substrates. Improvements will be implemented in monolithic integration, CIGS deposition, contact deposition, and in-situ CIGS control and monitoring. In Phase 1, GSE has successfully attacked many of the highest risk aspects of each task. All-laser, selective scribing processes for CIGS have been developed, and many end-of-contract goals for scribing speed have been exceeded in the first year. High-speed ink-jet deposition of insulating material in the scribes now appears to be a viable technique, again exceeding some end-of-contract goals in the first year. Absorber deposition of CIGS was reduced corresponding to throughput speeds of up to 24-in/min, also exceeding an end-of-contract goal. Alternate back-contact materials have been identified that show potential as candidates for replacement of higher-cost molybdenum, and a novel, real-time monitoring technique (parallel-detector spectroscopic ellipsometry) has shown remarkable sensitivity to relevant properties of the CIGS absorber layer for use as a diagnostic tool. Currently, one of the bilayers has been baselined by GSE for flexible CIGS on polymeric substrates. Resultant back-contacts meet sheet-resistance goals and exhibit much less intrinsic stress than Mo. CIGS has been deposited, and resultant devices are comparable in performance to pure Mo back-contacts. Debris in the chamber has been substantially reduced, allowing longer roll-length between system cleaning.

Quenching Mo optical losses in CIGS solar cells by a point contacted dual-layer dielectric spacer: a 3-D optical study.

Science.gov (United States)

Rezaei, Nasim; Isabella, Olindo; Vroon, Zeger; Zeman, Miro

2018-01-22

A 3-D optical modelling was calibrated to calculate the light absorption and the total reflection of fabricated CIGS solar cells. Absorption losses at molybdenum (Mo) / CIGS interface were explained in terms of plasmonic waves. To quench these losses, we assumed the insertion of a lossless dielectric spacer between Mo and CIGS, whose optical properties were varied. We show that such a spacer with low refractive index and proper thickness can significantly reduce absorption in Mo in the long wavelength regime and improve the device's rear reflectance, thus leading to enhanced light absorption in the CIGS layer. Therefore, we optimized a realistic two-layer MgF 2 / Al 2 O 3 dielectric spacer to exploit (i) the passivation properties of ultra-thin Al 2 O 3 on the CIGS side for potential high open-circuit voltage and (ii) the low refractive index of MgF 2 on the Mo side to reduce its optical losses. Combining our realistic spacer with optically-optimized point contacts increases the implied photocurrent density of a 750 nm-thick CIGS layer by 10% for the wavelengths between 700 and 1150 nm with respect to the reference cell. The elimination of plasmonic resonances in the new structure leads to a higher electric field magnitude at the bottom of CIGS layer and justifies the improved optical performance.

TEMPERATURE EFFECT OF ELECTRICAL PROPERTIES OF CIGS ...

African Journals Online (AJOL)

2011-06-30

Jun 30, 2011 ... Key words: Thin film solar cells, SCAPS, CIGS, temperature, effiency energetic. 1. INTRODUCTION ... technology are the low material consumption and the high efficiency that has been demonstrated, which .... [2] S. Wenham, M. Green, M. Watt, Applied Photovoltaics, The University of New. South Wales ...

7 CFR 1466.27 - Conservation Innovation Grants (CIG).

Science.gov (United States)

2010-01-01

..., evaluation, and implementation of: (i) Conservation adoption incentive systems, including market-based... 7 Agriculture 10 2010-01-01 2010-01-01 false Conservation Innovation Grants (CIG). 1466.27 Section... PROGRAM Contracts and Payments § 1466.27 Conservation Innovation Grants (CIG). (a) Definitions. In...

E-Cigs, Menthol & Dip

Science.gov (United States)

... Close Search × MENU BACK CLOSE SMOKEFREE.GOV HOME E-Cigs, Menthol & Dip There are many types of tobacco products. Learn how e-cigarettes, menthol cigarettes, smokeless tobacco, and other products ...

Design and long-term monitoring of DSC/CIGS tandem solar module

International Nuclear Information System (INIS)

Vildanova, M F; Nikolskaia, A B; Kozlov, S S; Shevaleevskiy, O I

2015-01-01

This paper describes the design and development of tandem dye-sensitized/Cu(In, Ga)Se (DSC/CIGS) PV modules. The tandem PV module comprised of the top DSC module and a bottom commercial 0,8 m 2 CIGS module. The top DSC module was made of 10 DSC mini-modules with the field size of 20 × 20 cm 2 each. Tandem DSC/CIGS PV modules were used for providing the long-term monitoring of energy yield and electrical parameters in comparison with standalone CIGS modules under outdoor conditions. The outdoor test facility, containing solar modules of both types and a measurement unit, was located on the roof of the Institute of Biochemical Physics in Moscow. The data obtained during monitoring within the 2014 year period has shown the advantages of the designed tandem DSC/CIGS PV-modules over the conventional CIGS modules, especially for cloudy weather and low-intensity irradiation conditions. (paper)

E-Cigs, Menthol & Dip

Science.gov (United States)

... are many types of tobacco products. Learn how e-cigarettes, menthol cigarettes, smokeless tobacco, and other products are ... your health. What We Know About Electronic Cigarettes (E-cigarettes) Some people use e-cigs to quit smoking. ...

Thin-Film CIGS Photovoltaic Technology: Annual Technical Report-Phase II, 16 April 1999-15 April 2000; ANNUAL

International Nuclear Information System (INIS)

Delahoy, A.E.; Bruns, J.; Ruppert, A.; Akhtar, M.; Chen, L.; Kiss, Z.J.

2000-01-01

A summary of Energy Photovoltaics' Phase II work includes the following: (1) EPV has demonstrated that it can sputter a Mo back-contact capable of supporting very high efficiency cell processing. Using EPV Mo, NREL has deposited a 17.1% CIGS cell (no AR coating). EPV believes it can identify the signature of''good'' Mo. The Mo was produced on EPV's 0.43 m(sup 2) pilot-line equipment; (2) EPV has performed compound synthesis for several classes of materials, namely non-Cu precursor materials, Cu-containing materials, and ternary buffer materials. Using a ternary compound synthesized at EPV (ZIS) as an evaporation source material for the buffer layer, a Cd-free CIGS device has been produced having an efficiency of 11.5% (560 mV, 32.1 mA/cm(sup 2), FF 64.3%). The ZIS films are photoconductive, and the devices exhibit no dark-light crossover or light soaking effects; (3) EPV initiated the interest of the University of Oregon in capacitance spectroscopy of CIGS devices. An Urbach tail with characteristic energy E0 and lt; 20meV was identified by transient photocapacitance spectroscopy; (4) Small-area CIGS devices were produced in the pilot-line system with an efficiency of 12.0% (581 mV, 30.1 mA/cm(sup 2), FF 68.7%), and in an R and D-scale system with 13.3% efficiency (569 mV, 34.1 mA/cm(sup 2), FF 68.1%); (5) An improved linear evaporation source for Cu delivery has been developed and was used for CIGS formation in the pilot-line system. The deposition width is 45 cm. This technological''tour de force'' allows EPV to build large-area CIGS systems possessing considerable flexibility. In particular, both EPV's FORNAX process and NREL's 3-stage process have been implemented on the pilot line. A CIGS thickness uniformity of 7% over a 40 cm width has been achieved; (6) A 4-head linear source assembly was designed, constructed, and is in use. Flux monitoring is practiced; (7) Large-area CIGS modules were produced with Voc's up to 36.3 V; (8) EPV has started to construct an

Development of CIGS2 solar cells with lower absorber thickness

Energy Technology Data Exchange (ETDEWEB)

Vasekar, Parag S.; Dhere, Neelkanth G. [Florida Solar Energy Center, University of Central Florida, 1679 Clearlake Rd., Cocoa, FL 32922 (United States); Moutinho, Helio [National Renewable Energy Laboratory, 1617 Cole Blvd. Golden, CO 80401 (United States)

2009-09-15

The availability and cost of materials, especially of indium can be a limiting factor as chalcopyrite based thin-film solar cells advance in their commercialization. The required amounts of metals can be lowered by using thinner films. When the thickness of the film decreases, there is possibility of remaining only in the small grain region because the coalescence of grains does not have an opportunity to enhance the grain size to the maximum. Solar cell performance in smaller grain chalcopyrite absorber deteriorates due to larger fraction of grain boundaries. Efforts are being made to reduce the thickness while maintaining the comparable performance. This work presents a study of preparation, morphology and other material properties of CIGS2 absorber layers with decreasing thicknesses up to 1.2 {mu}m and its correlation with the device performance. Encouraging results were obtained demonstrating that reasonable solar cell efficiencies (>10%) can be achieved even for thinner CIGS2 thin-film solar cells. (author)

Development of Enhanced Window layers for CIGS Photovoltaic Devices

Science.gov (United States)

Alexander, J. Nicholas

One of the most promising thin film devices right now is the Copper Indium Gallium Selenide (CIGS) solar cell with maximum reported power conversion efficiency of 22.3%. The Transparent Conducting Oxide (TCO) which is the top layer of the CIGS device also known as the window layer, is responsible for collecting the electrons generated in the CIGS device and conducting them to the circuit. Development of a very low resistivity film with a high optical transmission is crucial for optimal performance of devices as well as the ability to be deployed without changes to their properties for several decades. Current TCOs such as indium tin oxide (ITO) and aluminum doped zinc oxide (AZO) are met with limitations with either using large amounts of expensive materials such as indium, often requiring and anneal step to obtain good conductivity, or have shown poor long term reliability. This thesis is focused on development of InZnO and zirconium doped InZnO as a potential replacement TCO to obtain high conductivity and high transmission like the leading TCOs without needing heated depositions, post deposition annealing, and maintain a good film reliability. Zirconium doping was employed to farther enhance both the optical and electrical properties through enhancement of the films high frequency permittivity of InZnO while providing improved reliability to the film. The films were grown through a mix of DC and RF co-sputtering. InZnO films were deposited at varying indium concentration ( 10-30%) and samples were able to achieve low resistivity ( 7x10-4 O-cm), high mobility (>30 cm2/v.s), high carrier concentration (>10 20 cm-3), while maintaining high transmission (> 80%) in the visible and near-infrared region. After zirconium was incorporated into the InZnO films by replacement of the ZnO target with a ZrO2/ZnO (5:95) target, films of Zr:InZnO were deposit through the same method to achieve films that maintained very similar electrical and optical properties. The little

Low temperature deposition of bifacial CIGS solar cells on Al-doped Zinc Oxide back contacts

Energy Technology Data Exchange (ETDEWEB)

Cavallari, Nicholas, E-mail: nicholas.cavallari@imem.cnr.it [IMEM-CNR, Parco Area delle Scienze 37/a, 43124 Parma (Italy); Department of Mathematical, Physical and Computer Sciences, University of Parma, Parco Area delle Scienze 7/a, 43124 Parma (Italy); Pattini, Francesco; Rampino, Stefano; Annoni, Filippo [IMEM-CNR, Parco Area delle Scienze 37/a, 43124 Parma (Italy); Barozzi, Mario [FBK—CMM—Micro Nano Facility, Via Sommarive 18, 38123 Trento (Italy); Bronzoni, Matteo; Gilioli, Edmondo; Gombia, Enos [IMEM-CNR, Parco Area delle Scienze 37/a, 43124 Parma (Italy); Maragliano, Carlo [Solar Bankers LLC, Phoenix, AZ (United States); Mazzer, Massimo [IMEM-CNR, Parco Area delle Scienze 37/a, 43124 Parma (Italy); Pepponi, Giancarlo [FBK—CMM—Micro Nano Facility, Via Sommarive 18, 38123 Trento (Italy); Spaggiari, Giulia; Fornari, Roberto [IMEM-CNR, Parco Area delle Scienze 37/a, 43124 Parma (Italy); Department of Mathematical, Physical and Computer Sciences, University of Parma, Parco Area delle Scienze 7/a, 43124 Parma (Italy)

2017-08-01

Highlights: • AZO and CIGS were deposited by Low-Temperature Pulsed Electron Deposition (LT-PED). • CIGS/AZO contacts with ohmic behavior and resistance of 1.07 Ω cm{sup 2} were fabricated. • LT-PED deposition of AZO and CIGS prevents formation of Ga{sub 2}O{sub 3} interlayer. • CIGS-based bifacial solar cells with AZO back contact were realized. • Front PV efficiency of 9.3% and equivalent bifacial efficiency of 11.6% were achieved. - Abstract: We report on the fabrication and characterization of Cu(In,Ga)Se{sub 2} (CIGS)-based thin film bifacial solar cells using Al-doped ZnO (AZO) as cost-effective and non-toxic transparent back contact. We show that, by depositing both CIGS and AZO by Low Temperature Pulsed Electron Deposition at a maximum temperature of 250 °C, a good ohmic contact is formed between the two layers and good quality solar cells can be fabricated as a result. Photovoltaic efficiencies as high as 9.3% (front illumination), 5.1% (backside illumination) and 11.6% (bifacial illumination) have been obtained so far. These values are remarkably higher than those previously reported in the literature. We demonstrate that this improvement is ascribed to the low-temperature deposition process that avoids the formation of Ga{sub 2}O{sub 3} at the CIGS/AZO interface and favours the formation of a low-resistivity contact in agreement with device simulations.

An optimized efficient dual junction InGaN/CIGS solar cell: A numerical simulation

Science.gov (United States)

Farhadi, Bita; Naseri, Mosayeb

2016-08-01

The photovoltaic performance of an efficient double junction InGaN/CIGS solar cell including a CdS antireflector top cover layer is studied using Silvaco ATLAS software. In this study, to gain a desired structure, the different design parameters, including the CIGS various band gaps, the doping concentration and the thickness of CdS layer are optimized. The simulation indicates that under current matching condition, an optimum efficiency of 40.42% is achieved.

Thin-Film CIGS Photovoltaic Technology: Annual Technical Report-Phase II, 16 April 1999-15 April 2000

Energy Technology Data Exchange (ETDEWEB)

Delahoy, A.E.; Bruns, J.; Ruppert, A.; Akhtar, M.; Chen, L.; Kiss, Z.J.

2000-08-24

A summary of Energy Photovoltaics' Phase II work includes the following: (1) EPV has demonstrated that it can sputter a Mo back-contact capable of supporting very high efficiency cell processing. Using EPV Mo, NREL has deposited a 17.1% CIGS cell (no AR coating). EPV believes it can identify the signature of ``good'' Mo. The Mo was produced on EPV's 0.43 m{sup 2} pilot-line equipment; (2) EPV has performed compound synthesis for several classes of materials, namely non-Cu precursor materials, Cu-containing materials, and ternary buffer materials. Using a ternary compound synthesized at EPV (ZIS) as an evaporation source material for the buffer layer, a Cd-free CIGS device has been produced having an efficiency of 11.5% (560 mV, 32.1 mA/cm{sup 2}, FF 64.3%). The ZIS films are photoconductive, and the devices exhibit no dark-light crossover or light soaking effects; (3) EPV initiated the interest of the University of Oregon in capacitance spectroscopy of CIGS devices. An Urbach tail with characteristic energy E0 < 20meV was identified by transient photocapacitance spectroscopy; (4) Small-area CIGS devices were produced in the pilot-line system with an efficiency of 12.0% (581 mV, 30.1 mA/cm{sup 2}, FF 68.7%), and in an R and D-scale system with 13.3% efficiency (569 mV, 34.1 mA/cm{sup 2}, FF 68.1%); (5) An improved linear evaporation source for Cu delivery has been developed and was used for CIGS formation in the pilot-line system. The deposition width is 45 cm. This technological ``tour de force'' allows EPV to build large-area CIGS systems possessing considerable flexibility. In particular, both EPV's FORNAX process and NREL's 3-stage process have been implemented on the pilot line. A CIGS thickness uniformity of 7% over a 40 cm width has been achieved; (6) A 4-head linear source assembly was designed, constructed, and is in use. Flux monitoring is practiced; (7) Large-area CIGS modules were produced with Voc's up to 36

Toward GW/year of CIGS production within the next decade

Energy Technology Data Exchange (ETDEWEB)

Dhere, Neelkanth G. [Florida Solar Energy Center, 1679 Clearlake Road, Cocoa, FL 32922-5703 (United States)

2007-09-22

A detailed study carried out in 1996-1997 showed that manufacturing cost of crystalline silicon PV modules could be lowered to 1 ECU/Wp when the c-Si annual module production level reaches 500 MWp while an annual production of only 60 MWp would lower production cost of thin-film PV modules to 0.6 ECU/Wp. During 1976-2003, the PV module price has followed the 80% learning curve with cumulative production volume. However, the price reduction has slowed since because of the polysilicon supply problem. Because of their high potential for improvement, thin-film PV and especially copper (Cu)-indium (In)-gallium (Ga)-selenide (Se)-sulfide (CIGS) technology have the potential for growing at the fastest rate and consequently not only to complement the lagging c-Si PV production but also to assist in following the 80% learning curve. This paper reviews the CIGS PV manufacturing processes in comparison to those of other PV technologies and predicts that annual production volume of CIGS thin-film PV modules will exceed 1 GW/year within the next 10 years. (author)

Toward GW/year of CIGS production within the next decade

International Nuclear Information System (INIS)

Dhere, Neelkanth G.

2007-01-01

A detailed study carried out in 1996-1997 showed that manufacturing cost of crystalline silicon PV modules could be lowered to 1 ECU/Wp when the c-Si annual module production level reaches 500 MWp while an annual production of only 60 MWp would lower production cost of thin-film PV modules to 0.6 ECU/Wp. During 1976-2003, the PV module price has followed the 80% learning curve with cumulative production volume. However, the price reduction has slowed since because of the polysilicon supply problem. Because of their high potential for improvement, thin-film PV and especially copper (Cu)-indium (In)-gallium (Ga)-selenide (Se)-sulfide (CIGS) technology have the potential for growing at the fastest rate and consequently not only to complement the lagging c-Si PV production but also to assist in following the 80% learning curve. This paper reviews the CIGS PV manufacturing processes in comparison to those of other PV technologies and predicts that annual production volume of CIGS thin-film PV modules will exceed 1 GW/year within the next 10 years. (author)

Selenization of CIS and CIGS layers deposited by chemical spray pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Babu, B. J.; Egaas, B.; Velumani, S.

2018-03-21

Cu(In1-xGax)Se2 (CIGS) thin films with x=0 (CIS) and x=0.3 (CIGS) were prepared on Mo-coated glass substrate by using chemical spray pyrolysis at a substrate temperature of 350 degrees C, followed by selenization treatment at 550 degrees C in selenium environment under N2 gas flow. X-ray diffraction patterns of as-deposited CIGS layers on Mo showed polycrystalline chalcopyrite phase with an intense (112) plane. Splitting of (204)/(220) and (116)/(312) planes for the film with x=0.3 reveals deviation of tetragonal nature. Field emission scanning electron microscopy cross-sectional images of selenized films showed clear re-crystallization of grains. During the selenization process of the CIGS absorber, a thin interface layer of MoSe2 is formed. Line mapping of Mo/CIGS layer showed more gallium segregation at the interface of back contact resulting in band gap grading. Chemical composition and mapping of the as-deposited and selenized samples were determined by energy dispersive analysis of X-rays. This work leads to fabrication of low cost and large scale Mo/CIGS/CdS/ZnO/ZnO:Al device structure.

Analysis on the Performance of Copper Indium Gallium Selenide (CIGS Based Photovoltaic Thermal

Directory of Open Access Journals (Sweden)

Zulkepli Afzam

2016-01-01

Full Text Available This paper deals with the efficiency improvement of Copper Indium Gallium Selenide (CIGS Photovoltaic (PV and also solar thermal collector. Photovoltaic thermal (PV/T can improve overall efficiency for PV and also solve the problem of limited roof space at urban area. Objective of this study is to clarify the effect of mass flow rate on the efficiency of the PV/T system. A CIGS solar cell is used with rated output power 65 W and 1.18 m2 of area. 4 set of experiments were carried out, which were: thermal collector with 0.12 kg/s flow rate, PV/T with 0.12 kg/s flow rate, PV/T with 0.09 kg/s flow rate and PV. It was found that PV/T with 0.12 kg/s flow rate had the highest electrical efficiency, 2.92 %. PV/T with 0.09 kg/s flow rate had the lowest electrical efficiency, 2.68 %. It also had 2 % higher overall efficiency. The efficiency gained is low due to several factors. The rated output power of the PV is low for the area of 1.18 m2. The packing factor of the PV also need to be considered as it may not be operated at the optimal packing factor. Furthermore, aluminium sheet of the PV may affect the PV temperature due to high thermal conductivity. Further study on more values of mass flow rate and also other parameters that affect the efficiency of the PV/T is necessary.

A study on the optics of copper indium gallium (di)selenide (CIGS) solar cells with ultra-thin absorber layers.

Science.gov (United States)

Xu, Man; Wachters, Arthur J H; van Deelen, Joop; Mourad, Maurice C D; Buskens, Pascal J P

2014-03-10

We present a systematic study of the effect of variation of the zinc oxide (ZnO) and copper indium gallium (di)selenide (CIGS) layer thickness on the absorption characteristics of CIGS solar cells using a simulation program based on finite element method (FEM). We show that the absorption in the CIGS layer does not decrease monotonically with its layer thickness due to interference effects. Ergo, high precision is required in the CIGS production process, especially when using ultra-thin absorber layers, to accurately realize the required thickness of the ZnO, cadmium sulfide (CdS) and CIGS layer. We show that patterning the ZnO window layer can strongly suppress these interference effects allowing a higher tolerance in the production process.

Thin-Film CIGS Photovoltaic Technology; Annual Technical Report, Phase I; 16 April 1998 - 15 April 1999

International Nuclear Information System (INIS)

Chorobski, D.; Delahoy, A.E.; Kiss, Z.J.; Ziobro, F.

1999-01-01

This report describes work performed by Energy Photovoltaics, Inc. (EPV) under Phase I of this subcontract. EPV's new FORNAX process for CIGS formation is capable of producing devices with high Voc ( and gt;600 mV) and no dark aging effects. Parameters of the best device so far are Voc= 611 mV, Jsc= 27.5 mA/cm2, FF= 74.5%, and efficiency= 12.5%. A 34-cm2 16-cell minimodule was produced using FORNAX CIGS with Voc= 9.58 V, Isc= 52.0 mA, FF69.8%, and efficiency= 10.2%. A new version of EPV's linear evaporation source was developed with improved rate and uniformity for Cu deposition over a width of 45 cm. Using the new linear source, the FORNAX process was implemented on 0.43-m2 substrates in EPV's CIGS pilot line, with Voc= 537 mV and FF= 70.3% being achieved on a device. The EPV Subteam of the National CIS R and D Team has produced Cd-free ZnO/CIGS devices on NREL CIGS using the ROMEAO process (reaction of metal and atomic oxygen) for ZnO deposition. After soaking, the best device exhibited a Voc of 565 mV and an efficiency of 12.3%. Novel bias drive methods were devised for field soaking/anti-soaking experiments as a function of time and temperature. Scaling laws and an activation energy of 0.51 eV were found. Thermally stimulated capacitance reveals the existence of three distinct contributions to ZnO/CIGS device capacitance, two appearing to be gap-state effects and one related to net doping concentration. The coating time of the sputtered pilot-line ZnO:Al has been reduced by a factor of 3 while maintaining film quality. The deposition rate is 48 A s-1. Plans are under way to increase the substrate size from 0.43 m2 to 0.79 m2

Electrodeposition route to synthesize cigs films – an economical way ...

African Journals Online (AJOL)

user

Unlike binary conductors CIGS film preparation needs highly ... This argument also holds well in forming a hetero-junction partner CdS ..... successfully electrodeposited onto indium tin oxide substrate and it is recently reported (Li et al., 2010).

Thin film CIGS solar cells with a novel low cost process - Final report

Energy Technology Data Exchange (ETDEWEB)

Tiwari, A. N.; Romanyuk, Y.

2010-01-15

Novel manufacturing routes for efficient and low-cost Cu(In,Ga)Se{sub 2} (called CIGS) thin film solar cells are explored and patented. CIGS has proven its suitability for highly efficient and extremely stable solar cells. The low-cost methods allow impurity free material synthesis, fast large-area deposition, high material utilization and a very short energy payback time with drastically lower manufacturing costs. Two non-vacuum, solution-based approaches are investigated to deposit thin layers of CIGS. The first approach considers incorporation of copper into indium gallium selenide precursor layers by ion-exchange from aqueous or organic solutions. Organic solutions provide faster copper incorporation and do not corrode the metal back contact. Solar cells processed from selenized precursor films exhibit efficiencies of up to 4.1%. The second approach with paste coating of inorganic salt solution results in a solar cell efficiency of 4% (record 6.7%), where further improvements are hindered by the presence of the residual carbon layer. Using alternative organic binders, pre-deposited selenium layers, non-binder recipes helps to avoid the carbon layer although the obtained layers are inhomogeneous and contain impurity phases. A patent for the ion-exchange approach is pending, and the obtained research results on the paste coating approach will be scrutinized during new European FP7 project 'NOVA-CIGS'. (authors)

Optical characteristics of thin CIGS cells on TCO back contact

NARCIS (Netherlands)

Deelen, J. van; Kniknie, B.; Vroon, Z.A.E.P.; Wuerz, R.; Kessler, F.

2014-01-01

Reduction of CIGS layer thickness could translate in significant cost reduction. CIGS was made on transparent conductive oxide (TCO) to allow for optical characterization. This data was compared with external quantum efficiency (EQE) data. The results suggest that changes in surface morphology are

Process parameter impact on properties of sputtered large-area Mo bilayers for CIGS thin film solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Badgujar, Amol C.; Dhage, Sanjay R., E-mail: dhage@arci.res.in; Joshi, Shrikant V.

2015-08-31

Copper indium gallium selenide (CIGS) has emerged as a promising candidate for thin film solar cells, with efficiencies approaching those of silicon-based solar cells. To achieve optimum performance in CIGS solar cells, uniform, conductive, stress-free, well-adherent, reflective, crystalline molybdenum (Mo) thin films with preferred orientation (110) are desirable as a back contact on large area glass substrates. The present study focuses on cylindrical rotating DC magnetron sputtered bilayer Mo thin films on 300 mm × 300 mm soda lime glass (SLG) substrates. Key sputtering variables, namely power and Ar gas flow rates, were optimized to achieve best structural, electrical and optical properties. The Mo films were comprehensively characterized and found to possess high degree of thickness uniformity over large area. Best crystallinity, reflectance and sheet resistance was obtained at high sputtering powers and low argon gas flow rates, while mechanical properties like adhesion and residual stress were found to be best at low sputtering power and high argon gas flow rate, thereby indicating a need to arrive at a suitable trade-off during processing. - Highlights: • Sputtering of bilayer molybdenum thin films on soda lime glass • Large area deposition using rotating cylindrical direct current magnetron • Trade of sputter process parameters power and pressure • High uniformity of thickness and best electrical properties obtained • Suitable mechanical and optical properties of molybdenum are achieved for CIGS application.

Vaping cannabis (marijuana): parallel concerns to e-cigs?

OpenAIRE

Budney, Alan J.; Sargent, James D.; Lee, Dustin C.

2015-01-01

The proliferation of vaporization (‘vaping’) as a method for administering cannabis raises many of the same public health issues being debated and investigated in relation to e-cigarettes (e-cigs). Good epidemiological data on the prevalence of vaping cannabis are not yet available, but with current trends towards societal approval of medicinal and recreational use of cannabis, the pros and cons of vaping cannabis warrant study. As with e-cigs, vaping cannabis portends putative health benefit...

Alternative bufferlayers for CIGS solarcells

Energy Technology Data Exchange (ETDEWEB)

Beleanu, A.; Gruhn, T.; Blum, C.G.F.; Balke, B.; Felser, C. [Institute of Inorganic and Analytical Chemistry, Johannes Gutenberg - University, Mainz (Germany)

2010-07-01

Cadmium sulfide is a highly efficient buffer layer material in Cu(In,Ga)(S,Se2)[CIGS] solar devices, but for environmental reasons and possible gains in efficiency there is a great interest in replacing CdS by a cadmium-free alternative buffer layer. Using standard density functional theory (DFT) methods possible candidates like LiZnP and LiCuS have been proposed as alternative buffer layers. The experimental verification of the DFT results was quite challenging due to the fact that LiCuS was an unknow and completely new material. In a first step, we tried to synthesize LiCuS through solid state reactions in a corund crucible. After optimizing the parameters and successfully synthesizing the material its properties were investigated. In a second step, huge amounts of LiCuS and LiZnP were synthesized and pressed using Spark Plasma Sintering as 3 inch targets. LiCuS and LiZnP films were grown by radio-frequency magnetron sputtering from these target and their properties as an alternative buffer layer in CIGS solar cells were investigated. The 1:1:1 stoichiometry of the films was delivered from in-situ XPS measurements. Absorption measurements show a band gap of {approx}2.0 eV which is in good agreement with the theoretical estimates.

Effect of yoghurt or yoghurt serum on microbial quality of cig kofte.

Science.gov (United States)

Dogan, Mahmut; Cankurt, Hasan; Toker, Omer Said; Yetim, Hasan; Sagdic, Osman

2014-07-01

Cig kofte, raw meatball is a traditionally produced meat product in Turkey and some other Middle East countries. It is prepared from mixtures of finely minced raw beef, bulgur, onions, various spices and tap water. Cig kofte is an uncooked product and popularly consumed with lettuce and lemon juice. In this study, yoghurt or yoghurt serum (YS) were added to the mixtures of cig kofte instead of tap water to reduce microbial risks of the raw meatball. Additionally, the effects of yoghurt and YS on some physicochemical characteristics of cig kofte were investigated. Cig kofte is generally consumed within a few hours after the preparation because of its raw nature. Also, it is generally sold under unhygienic conditions in restaurants and restaurant-like places. For this purpose, reducing of the microbial load of cig kofte is important. In the results, Escherichia coli and Listeria monocytogenes were not detected in any samples. While lactic acid bacteria count increased by addition of yoghurt and YS, the number of other microorganisms except for total aerobic mesophilic bacteria (TAMB) were decreased. The aw values and% moisture contents of the samples were varied between 0.88-0.94 and 46.25-49.72, respectively. The pH values of the samples were slightly changed during the storage of 24 h while no changes detected in the control samples during the storage. In conclusion, it can be suggested that using the yoghurt or YS instead of tap water in the preparation of cig kofte might ensure the microbial safety, increase the nutritional value and its flavour or aroma.

Enhancement of the CIGS solar cell's efficiency by anti-reflection coating with teflon AF

Energy Technology Data Exchange (ETDEWEB)

Bae, Hong-Sub; Kim, Chan; Rhee, Il-Su [Kyungpook National University, Daegu (Korea, Republic of); Jo, Hyun-Jun; Kim, Dae-Hwan [Daegu Gyeongbuk Institute of Science and Technology, Daegu (Korea, Republic of); Hong, Sung-Wook [Daegu University, Gyeongsan (Korea, Republic of)

2014-11-15

An anti-reflection (AR) layer of Teflon AF was deposited on the front surface of a Cu(In,Ga)Se{sub 2} (CIGS) solar cell with a structure of grid/TCO/ZnO/CdS/Cu(In,Ga)Se{sub 2}/Mo/glass by using the spin coating method. This AR layer reduced the front-surface reflection, which resulted in high efficiency for the CIGS solar cell. The thickness of the Teflon AF layer was varied to determine the thickness that gave the highest transmittance of incident light into the active absorber of the CIGS solar cell. The optimum thickness of the Teflon AF layer was found to be 105 nm. CIGS solar cells with a Teflon AF layer of 105 nm were constructed, and their efficiencies were compared with those of solar cells without a Teflon AF layer. The average increase in the relative efficiency of the solar cells was 2.63% due to the inclusion of an anti-reflection layer of Teflon AF.

Electrodeposition of ZnO-doped films as window layer for Cd-free CIGS-based solar cells

Science.gov (United States)

Tsin, Fabien; Vénérosy, Amélie; Hildebrandt, Thibaud; Hariskos, Dimitrios; Naghavi, Negar; Lincot, Daniel; Rousset, Jean

2016-02-01

The Cu(In,Ga)Se2 (CIGS) thin film solar cell technology has made a steady progress within the last decade reaching efficiency up to 22.3% on laboratory scale, thus overpassing the highest efficiency for polycrystalline silicon solar cells. High efficiency CIGS modules employ a so-called buffer layer of cadmium sulfide CdS deposited by Chemical Bath Deposition (CBD), which presence and Cd-containing waste present some environmental concerns. A second potential bottleneck for CIGS technology is its window layer made of i-ZnO/ZnO:Al, which is deposited by sputtering requiring expensive vacuum equipment. A non-vacuum deposition of transparent conductive oxide (TCO) relying on simpler equipment with lower investment costs will be more economically attractive, and could increase competitiveness of CIGS-based modules with the mainstream silicon-based technologies. In the frame of Novazolar project, we have developed a low-cost aqueous solution photo assisted electrodeposition process of the ZnO-based window layer for high efficiency CIGS-based solar cells. The window layer deposition have been first optimized on classical CdS buffer layer leading to cells with efficiencies similar to those measured with the sputtered references on the same absorber (15%). The the optimized ZnO doped layer has been adapted to cadmium free devices where the CdS is replaced by chemical bath deposited zinc oxysulfide Zn(S,O) buffer layer. The effect of different growth parameters has been studied on CBD-Zn(S,O)-plated co-evaporated Cu(In,Ga)Se2 substrates provided by the Zentrum für Sonnenenergie-und Wasserstoff-Forschung (ZSW). This optimization of the electrodeposition of ZnO:Cl on CIGS/Zn(S,O) stacks led to record efficiency of 14%, while the reference cell with a sputtered (Zn,Mg)O/ZnO:Al window layer has an efficiency of 15.2%.

Novel in situ resistance measurement for the investigation of CIGS growth in a selenization process

International Nuclear Information System (INIS)

Liu Wei; He Qing; Li Fengyan; Li Changjian; Sun Yun; Tian Jianguo; Li Zubin

2009-01-01

During the selenization process of CIGS thin films, the relation between the element loss rate and the precursor depositions are analyzed. The growth of the CIGS thin films during the selenization process is investigated by the novel in situ resistance measurement, by which the formation of compound semiconductors can be observed directly and simultaneously. Their structures, phase evolutions and element losses are analyzed by XRD and XRF. Based on the experimental results, it can be concluded that the phase transforms have nothing to do with the deposition sequences of precursors, while the element loss rates are related to the deposition sequences in this process. In addition, element loss mechanisms of CIGS thin films prepared by the selenization process are analyzed by the phase evolutions and chemical combined path in the In, Ga–Se reaction processes. Moreover it is verified that the element losses are depressed by increasing the ramping-up rate finally. The results provide effective methods to fabricate high-quality CIGS thin films with low element losses

Novel in situ resistance measurement for the investigation of CIGS growth in a selenization process

Science.gov (United States)

Liu, Wei; Tian, Jian-Guo; Li, Zu-Bin; He, Qing; Li, Feng-Yan; Li, Chang-Jian; Sun, Yun

2009-03-01

During the selenization process of CIGS thin films, the relation between the element loss rate and the precursor depositions are analyzed. The growth of the CIGS thin films during the selenization process is investigated by the novel in situ resistance measurement, by which the formation of compound semiconductors can be observed directly and simultaneously. Their structures, phase evolutions and element losses are analyzed by XRD and XRF. Based on the experimental results, it can be concluded that the phase transforms have nothing to do with the deposition sequences of precursors, while the element loss rates are related to the deposition sequences in this process. In addition, element loss mechanisms of CIGS thin films prepared by the selenization process are analyzed by the phase evolutions and chemical combined path in the In, Ga-Se reaction processes. Moreover it is verified that the element losses are depressed by increasing the ramping-up rate finally. The results provide effective methods to fabricate high-quality CIGS thin films with low element losses.

Computational Infrastructure for Geodynamics (CIG)

Science.gov (United States)

Gurnis, M.; Kellogg, L. H.; Bloxham, J.; Hager, B. H.; Spiegelman, M.; Willett, S.; Wysession, M. E.; Aivazis, M.

2004-12-01

Solid earth geophysicists have a long tradition of writing scientific software to address a wide range of problems. In particular, computer simulations came into wide use in geophysics during the decade after the plate tectonic revolution. Solution schemes and numerical algorithms that developed in other areas of science, most notably engineering, fluid mechanics, and physics, were adapted with considerable success to geophysics. This software has largely been the product of individual efforts and although this approach has proven successful, its strength for solving problems of interest is now starting to show its limitations as we try to share codes and algorithms or when we want to recombine codes in novel ways to produce new science. With funding from the NSF, the US community has embarked on a Computational Infrastructure for Geodynamics (CIG) that will develop, support, and disseminate community-accessible software for the greater geodynamics community from model developers to end-users. The software is being developed for problems involving mantle and core dynamics, crustal and earthquake dynamics, magma migration, seismology, and other related topics. With a high level of community participation, CIG is leveraging state-of-the-art scientific computing into a suite of open-source tools and codes. The infrastructure that we are now starting to develop will consist of: (a) a coordinated effort to develop reusable, well-documented and open-source geodynamics software; (b) the basic building blocks - an infrastructure layer - of software by which state-of-the-art modeling codes can be quickly assembled; (c) extension of existing software frameworks to interlink multiple codes and data through a superstructure layer; (d) strategic partnerships with the larger world of computational science and geoinformatics; and (e) specialized training and workshops for both the geodynamics and broader Earth science communities. The CIG initiative has already started to

Microstructural evolution of all-wet-processed CIGS films using Raman spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Choi, Hee Soo; Choi, Eunmi; Kim, Areum; Pyo, Sung Gyu [School of Integrative Engineering, Chung-Ang University, 221 Heukseok-Dong, Seoul, 156-756 (Korea, Republic of); Yoon, Sung Pil [Fuel Cell Research Center, Korea Institute of Science and Technology, Seoul, 136-791 (Korea, Republic of)

2014-08-15

We report a wet process deposition in order to identify a cost-effective processing scheme for CuIn{sub 1-x}Ga{sub x}Se{sub 2} (CIGS) layers on molybdenum/soda lime glass substrates from a Cu-In-Ga precursor solution. We employed a spin coater at various settings to evaluate the uniformity of the resulting CIGS solar cell layer. After the CIGS precursor film was deposited, we applied a selenization process. In the selenization process, we used a controlled temperature RTA system and compared it to a noncontrolled temperature system. We investigated the morphological properties for different selenization temperature treatments. We used Raman mapping to detect binary compounds and found the binary compound effect on the film. Raman mapping results show that the density of the binary compound in the CIGS layer increased with selenization temperature, and at 600 C, the density of the binary compounds was highest. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Semi-transparent perovskite solar cells for tandems with silicon and CIGS

KAUST Repository

Bailie, Colin D.

2015-01-01

© 2015 The Royal Society of Chemistry. A promising approach for upgrading the performance of an established low-bandgap solar technology without adding much cost is to deposit a high bandgap polycrystalline semiconductor on top to make a tandem solar cell. We use a transparent silver nanowire electrode on perovskite solar cells to achieve a semi-transparent device. We place the semi-transparent cell in a mechanically-stacked tandem configuration onto copper indium gallium diselenide (CIGS) and low-quality multicrystalline silicon (Si) to achieve solid-state polycrystalline tandem solar cells with a net improvement in efficiency over the bottom cell alone. This work paves the way for integrating perovskites into a low-cost and high-efficiency (>25%) tandem cell.

Degradation of CIGS solar cells

NARCIS (Netherlands)

Theelen, M.J.

2015-01-01

Thin film CIGS solar cells and individual layers within these solar cells have been tested in order to assess their long term stability. Alongside with the execution of standard tests, in which elevated temperatures and humidity levels are used, the solar cells have also been exposed to a

Reusing a declarative specification to check the conformance of different CIGs

NARCIS (Netherlands)

Grando, M.A.; Aalst, van der W.M.P.; Mans, R.S.; Daniel, F.; Barkaoui, K.; Dustdar, S.

2012-01-01

Several Computer Interpretable Guidelines (CIGs) languages have been proposed by the health community. Even though these CIG languages share common ideas each language has to be provided with his own mechanism of verification. In an earlier work we have shown that a DECLARE model can be used for

High throughput CIGS solar cell fabrication via ultra-thin absorber layer with optical confinement and (Cd, CBD)-free heterojunction partner

Energy Technology Data Exchange (ETDEWEB)

Marsillac, Sylvain [Old Dominion Univ., Norfolk, VA (United States)

2015-11-30

The main objective of this proposal was to use several pathways to reduce the production cost of Cu(In,Ga)Se₂ (CIGS) PV modules and therefore the levelized cost of energy (LCOE) associated with this technology. Three high cost drivers were identified, nominally: 1) Materials cost and availability; 2) Large scale uniformity; 3) Improved throughput These three cost drivers were targeted using the following pathways: 1) Reducing the thickness of the CIGS layer while enhancing materials quality; 2) Developing and applying enhanced in-situ metrology via real time spectroscopic ellipsometry; 3) Looking into alternative heterojunction partner, back contact and anti-reflection (AR) coating Eleven main Tasks were then defined to achieve these goals (5 in Phase 1 and 6 in Phase 2), with 11 Milestones and 2 Go/No-go decision points at the end of Phase 1. The key results are summarized below

Surface Passivation of CIGS Solar Cells Using Gallium Oxide

KAUST Repository

Garud, Siddhartha

2018-02-27

This work proposes gallium oxide grown by plasma-enhanced atomic layer deposition, as a surface passivation material at the CdS buffer interface of Cu(In,Ga)Se2 (CIGS) solar cells. In preliminary experiments, a metal-insulator-semiconductor (MIS) structure is used to compare aluminium oxide, gallium oxide, and hafnium oxide as passivation layers at the CIGS-CdS interface. The findings suggest that gallium oxide on CIGS may show a density of positive charges and qualitatively, the least interface trap density. Subsequent solar cell results with an estimated 0.5 nm passivation layer show an substantial absolute improvement of 56 mV in open-circuit voltage (VOC), 1 mA cm−2 in short-circuit current density (JSC), and 2.6% in overall efficiency as compared to a reference (with the reference showing 8.5% under AM 1.5G).

Growth and structural properties of reactively co-sputtered CIGS films and their solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Kim, Jeha [Cheongju University, Cheongju (Korea, Republic of); Park, Nae-Man [Electronics and Telecommunications Research Institute, Daejeon (Korea, Republic of)

2014-02-15

Using reactive sputtering, we fabricated stoichiometric CuIn{sub 1-x}Ga{sub x}Se{sub 2} (CIGS) thin films. Both Cu{sub 0.6}Ga{sub 0.4} (CuGa) and Cu{sub 0.4}In{sub 0.6} (CuIn) alloy targets were simultaneously sputtered under the delivery of elemental Se produced from a thermal cracker. By changing the sputtering rates of the CuGa and the CuIn, we were able to obtain the composition ratios of Cu/(Ga+In) and Ga/(Ga+In) in the range of 0.71-0.95 and 0.10-0.30, respectively. Both the grain size and the surface roughness of the CIGS film increased as the Cu/(Ga+In) ratio increased. In the X-ray diffraction analysis on CIGS films of 0.9 m, preferential growth with a [112] orientation was found, and reflections from the (211), (220)/(204), (301), (312)/(116), (400)/(008), and (332)/(316) planes were observed. The CIGS films showed the existence of Cu{sub 2-x}Se phases in the Cu-rich samples and ordered defect compound (ODC) phases in the Cu-poor films, as confirmed in the Raman measurements. A best device performance of η = 8.1%, V{sub oc} = 0.442 V, J{sub sc} = 34.3 mA/cm{sup 2}, and FF = 53.4% was obtained from a cell fabricated with a CIGS layer (t = 0.9 μm) with the Cu/(Ga+In) ratio = 0.71 and the Ga/(Ga+In) ratio = 0.10.

An investigation on preparation of CIGS targets by sintering process

Energy Technology Data Exchange (ETDEWEB)

Zhang Ning, E-mail: zhn98@126.co [Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China); Zhuang Daming; Zhang Gong [Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

2010-01-15

Pressureless sintering process was used to fabricate CIGS targets with Cu{sub 2}Se, In{sub 2}Se{sub 3}, and Ga{sub 2}Se{sub 3} as raw powders mixed according to the stoichiometry of CuIn{sub 0.72}Ga{sub 0.28}Se{sub 2} (CIGS). The results showed that only CuIn{sub 0.7}Ga{sub 0.3}Se{sub 2} phase can be detected in the sintered targets. The pores in sintered specimen become smaller and distribute more homogeneously under the conditions of finer powders and higher cold pressure. Both mass loss caused by the formation of volatile phase relating to Ga and volume expansion occur during the sintering process, which result in the decrease of density. The tendency of anti-densification becomes stronger under the conditions of coarser powders and higher cold pressure. The sintering process and causes for anti-densification were discussed. Finally, a hot pressing process was carried out, which was proved to be fairly effective to increase the density of CIGS target. The fabricated target can be used for magnetron-sputtering deposition of CIGS absorbers.

Modeling and simulation of a dual-junction CIGS solar cell using Silvaco ATLAS

OpenAIRE

Fotis, Konstantinos

2012-01-01

Approved for public release; distribution is unlimited. The potential of designing a dual-junction Copper Indium Gallium Selenide (CIGS) photovoltaic cell is investigated in this thesis. Research into implementing a dual-junction solar cell, using a CIGS bottom cell and different thin-film designs as a top cell, was conducted in order to increase the current record efficiency of 20.3% for a single CIGS cell. This was accomplished through modeling and simulation using Silvaco ATLASTM, an ad...

Sputtered molybdenum thin films and the application in CIGS solar cells

Energy Technology Data Exchange (ETDEWEB)

Zhou, D.; Zhu, H., E-mail: hongbing1982@hotmail.com; Liang, X.; Zhang, C.; Li, Z.; Xu, Y.; Chen, J.; Zhang, L.; Mai, Y., E-mail: yaohuamai@hbu.edu.cn

2016-01-30

Graphical abstract: - Highlights: • Mo thin films are prepared by magnetron sputtering. • The dynamic deposition rate increases with the increasing discharge power. • The surface structure of Mo films varies with discharge power and working pressure. • High efficiency CIGS thin film solar cell of 15.2% has been obtained. - Abstract: Molybdenum (Mo) thin films are prepared by magnetron sputtering with different discharge powers and working pressures for the application in Cu(In, Ga)Se{sub 2} (CIGS) thin film solar cells as back electrodes. Properties of these Mo thin films are systematically investigated. It is found that the dynamic deposition rate increases with the increasing discharge power while decreases with the increasing working pressure. The highest dynamic deposition rate of 15.1 nm m/min is achieved for the Mo thin film deposited at the discharge power of 1200 W and at the working pressure of 0.15 Pa. The achieved lowest resistivity of 3.7 × 10{sup −5} Ω cm is attributed to the large grains in the compact thin film. The discharge power and working pressure have great influence on the sputtered Mo thin films. High efficiency of 12.5% was achieved for the Cu(In, Ga)Se{sub 2} (CIGS) thin film solar cells with Mo electrodes prepared at 1200 W and low working pressures. By further optimizing material and device properties, the conversion efficiency has reached to 15.2%.

Integration of Solar Cells on Top of CMOS Chips - Part II: CIGS Solar Cells

NARCIS (Netherlands)

Lu, J.; Liu, Wei; Kovalgin, Alexeij Y.; Sun, Yun; Schmitz, Jurriaan

2011-01-01

We present the monolithic integration of deepsubmicrometer complementary metal–oxide–semiconductor (CMOS) microchips with copper indium gallium (di)selenide (CIGS) solar cells. Solar cells are manufactured directly on unpackaged CMOS chips. The microchips maintain comparable electronic performance,

Vaping cannabis (marijuana): parallel concerns to e-cigs?

Science.gov (United States)

Budney, Alan J; Sargent, James D; Lee, Dustin C

2015-11-01

The proliferation of vaporization ('vaping') as a method for administering cannabis raises many of the same public health issues being debated and investigated in relation to e-cigarettes (e-cigs). Good epidemiological data on the prevalence of vaping cannabis are not yet available, but with current trends towards societal approval of medicinal and recreational use of cannabis, the pros and cons of vaping cannabis warrant study. As with e-cigs, vaping cannabis portends putative health benefits by reducing harm from ingesting toxic smoke. Indeed, vaping is perceived and being sold as a safer way to use cannabis, despite the lack of data on the health effects of chronic vaping. Other perceived benefits include better taste, more efficient and intense effects and greater discretion which allows for use in more places. Unfortunately, these aspects of vaping could prompt an increased likelihood of trying cannabis, earlier age of onset, more positive initial experiences, and more frequent use, thereby increasing the probability of problematic use or addiction. Sales and marketing of vaping devices with no regulatory guidelines, especially related to advertising or product development targeting youth, parallels concerns under debate related to e-cigs and youth. Thus, the quandary of whether or not to promote vaping as a safer method of cannabis administration for those wishing to use cannabis, and how to regulate vaping and vaping devices, necessitates substantial investigation and discussion. Addressing these issues in concert with efforts directed towards e-cigs may save time and energy and result in a more comprehensive and effective public health policy on vaping. © 2015 Society for the Study of Addiction.

Experimental and theoretical investigations of structural and optical properties of CIGS thin films

Energy Technology Data Exchange (ETDEWEB)

Chandramohan, M., E-mail: chandramohan59@yahoo.co.in [Department of Physics, Park college of Engineering and Tecknology, Coimbatore-641 659 (India); Velumani, S., E-mail: vels64@yahoo.com [Centro de Investigacion y de Estudios Avanzados del I.P.N.(CINVESTAV), Av. Instituto Politecnico Nacional 2508 Col. San Pedro Zacatenco 07360, Mexico D.F (Mexico); Venkatachalam, T., E-mail: atvenkatachalam@yahoo.com [Department of Physics, Coimbatore Institute of Technology, Coimbatore-14. India (India)

2010-10-25

Experimental and theoretical studies of the structural and optical properties of Copper Indium Gallium diSelenide thin films have been performed. Thin films of CIGS were deposited on glass substrates by chemical bath deposition. From the XRD results of the films, it is found that the films are of chalcopyrite type structure. The lattice parameter were determined as a = 5.72 A and c = 11.462 A. The optical properties of the thin films were carried out with the help of spectrophotometer. First principles density functional theory calculations of the band structure, density of states and effective masses of electrons and holes of the CIGS crystals have been done by computer simulations. The experimental data and theoretically calculated data have demonstrated good agreement.

One-pot Synthesis of Soluble Nanoscale CIGS Photoactive Functional Materials

Directory of Open Access Journals (Sweden)

Yan Aixia

2007-01-01

Full Text Available Abstract Promising alternatives for solar energy utilization are thin film technologies involving various new materials. This contribution describes an easy and inexpensive synthetic method that can be used to prepare soluble nanoscale triphenyl phosphine-coordinated CIGS (TPP-CIGS photoactive functional materials. This complex is stable in the solid state under the irradiation of the ambient light, but its solution becomes a little bit unstable under the illumination of the low intensity laser.

Effect of annealing on the structural properties of electron beam deposited CIGS thin films

Energy Technology Data Exchange (ETDEWEB)

Venkatachalam, M. [Department of Electronics, Erode Arts College, Erode (India)], E-mail: prabhu7737@yahoo.com; Kannan, M.D.; Jayakumar, S.; Balasundaraprabhu, R. [Thin Film Center, PSG College of Technology, Coimbatore (India); Muthukumarasamy, N. [Department of Physics, Coimbatore Institute of Technology, Coimbatore (India)

2008-08-30

CIGS bulk compound of three different compositions CuIn{sub 0.85}Ga{sub 0.15}Se{sub 2}, CuIn{sub 0.80}Ga{sub 0.20}Se{sub 2} and CuIn{sub 0.75}Ga{sub 0.25}Se{sub 2} have been prepared by direct reaction of elemental copper, indium, gallium and selenium. CIGS thin films of the three compositions have been deposited onto glass and silicon substrates using the prepared bulk by electron beam deposition method. The structural properties of the deposited films have been studied using X-ray diffraction technique. The as-deposited CIGS films have been found to be amorphous in nature. To study the effect of annealing on the structural properties, the films have been annealed in vacuum of the order of 10{sup -5} Torr. The X-ray diffractograms of the annealed CIGS films exhibited peaks revealing that the annealed films are crystalline in nature with tetragonal chalcopyrite structure. The (112) peak corresponding to the chalcopyrite structure has been observed to be the dominating peak in all the annealed films. The position of the (112) peak and other peaks in the X-ray diffraction pattern has been observed to shift to higher values of 2{theta} with the increase of gallium concentration. The lattice parameter values 'a' and 'c' have been calculated and they are found to be dependent on the concentration of gallium in the films. The FWHM in the X-ray diffraction pattern is found to decrease with an increase in annealing temperature indicating that the crystalline nature of the CIGS improves with increase in annealing temperature. The films grown on silicon substrates have been found to be of better crystalline quality than those deposited on glass substrates. The micro structural parameters like grain size, dislocation density and strain have been evaluated. The chemical constituents present in the deposited CIGS films have been identified using energy dispersive X-ray analysis. The surface topographical study on the films has been performed by AFM. The

Significant effect of substrate temperature on the phase structure, optical and electrical properties of RF sputtered CIGS films

Energy Technology Data Exchange (ETDEWEB)

Yu Zhou; Yan Yong; Li Shasha; Zhang Yanxia; Yan Chuanpeng; Liu Lian; Zhang Yong [Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Superconductivity and New energy R and D Center (SNERDC), Mail Stop 165, Southwest Jiaotong University, Chengdu 610031 (China); Zhao Yong, E-mail: yzhao@swjtu.edu.cn [Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Superconductivity and New energy R and D Center (SNERDC), Mail Stop 165, Southwest Jiaotong University, Chengdu 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney 2052, NSW (Australia)

2013-01-01

Highlights: Black-Right-Pointing-Pointer Secondary phase exist in the RF sputtered CIGS films as it deposited at 150 Degree-Sign C and 500 Degree-Sign C. Black-Right-Pointing-Pointer CIGS films deposited beyond 350 Degree-Sign C show (1 1 2) prefer orientation. Black-Right-Pointing-Pointer E{sub g} of the CIGS films increased with the increase of substrate temperature. Black-Right-Pointing-Pointer Conductivity of the films is affected by 'variable range hopping' mechanism. - Abstract: This work studied the effect of substrate temperature on the phase structure, optical and electrical properties of the one-step radio frequency sputtered Cu(In,Ga)Se{sub 2} (CIGS) thin films. X-ray diffraction (XRD) analysis revealed that all the deposited CIGS films are chalcopyrite phase with polycrystalline structure. The films deposited beyond the substrate temperature of 350 Degree-Sign C show (1 1 2) prefer orientation. Raman spectra reveal that the 150 Degree-Sign C deposited CIGS film coexists with Cu{sub 2-x}Se phase and the 500 Degree-Sign C deposited film contains ordered defect compound (ODC) phase. With the increase of substrate temperature, energy band gap of the CIGS film increase from 0.99 to 1.27 eV. Films deposited at higher temperature exhibit larger electrical conductivity. Conductivity of the CIGS films is dominated by 'variable range hopping' mechanism. The disorder in our CIGS the films is associated with the formation of intrinsic defects such as V{sub Se} and In{sub Cu} for their low formation energy.

OTRZYMYWANIE CIENKICH WARSTW ABSORBERA CIGS METODĄ ROZPYLANIA MAGNETRONOWEGO DLA ZASTOSOWAŃ FOTOWOLTAICZNYCH

Directory of Open Access Journals (Sweden)

Sławomir GUŁKOWSKI

w cienkowarstwowych ogniwach słonecznych. Metoda rozpylania magnetronowego jest efektywną metodą produkcji cienkich warstw CIGS. Proces nanoszenia warstw można podzielić na dwie zasadnicze części: pierwsza to tworzenie prekursora CIG, tj. nanoszenie warstw metalicznych miedzi, galu i indu w odpowiednich proporcjach. Etap drugi to krystalizacja absorbera CIGS w wyniku procesu wygrzewania prekursora w obecności selenu. W artykule skupiono się na opracowaniu odpowiednich proporcji poszczególnych pierwiastków wchodzących w skład prekursora. Przebadano następujące konfiguracje nanoszenia poszczególnych warstw absorbera: CuGa/In oraz CuGa/In/Cu. Poszczególne warstwy naniesione zostały na podłoże molibdenowe, stanowiące tylny kontakt ogniwa budowanego na bazie absorbera CIGS. Warstwa molibdenu została przebadana metodą czteroostrzową w celu znalezienia zależności rezystywności od grubości warstwy. Przeprowadzono analizę składu pierwiastkowego warstwy za pomocą skaningowego mikroskopu elektronowego wyposażonego w system EDS. Dla każdej z otrzymanych warstw określono atomowe współczynniki proporcji występowania miedzi oraz galu w składzie warstwy. Na podstawie otrzymanych wyników badań dokonano optymalizacji parametrów technologicznych procesu takich jak: moc katody, ciśnienie oraz czas procesu, a także temperatura. Znaleziono zależności grubości warstw w funkcji czasu nanoszenia dla ustalonych warunków ciśnienia i mocy. Grubości poszczególnych warstw określono na podstawie badań profilometrycznych. W oparciu o opracowane parametry wykonane warstwy prekursora poddawane są obróbce termicznej w celu uzyskania absorbera CIGS.

Nanosecond laser scribing of CIGS thin film solar cell based on ITO bottom contact

Science.gov (United States)

Kuk, Seungkuk; Wang, Zhen; Fu, Shi; Zhang, Tao; Yu, Yi Yin; Choi, JaeMyung; Jeong, Jeung-hyun; Hwang, David J.

2018-03-01

Cu(In,Ga)Se2 (CIGS) thin films, a promising photovoltaic architecture, have mainly relied on Molybdenum for the bottom contact. However, the opaque nature of Molybdenum (Mo) poses limitations in module level fabrication by laser scribing as a preferred method for interconnect. We examined the P1, P2, and P3 laser scribing processes on CIGS photovoltaic architecture on the indium tin oxide (ITO) bottom contact with a cost-effective nanosecond pulsed laser of 532 nm wavelength. Laser illuminated from the substrate side, enabled by the transparent bottom contact, facilitated selective laser energy deposition onto relevant interfaces towards high-quality scribing. Parametric tuning procedures are described in conjunction with experimental and numerical investigation of relevant mechanisms, and preliminary mini-module fabrication results are also presented.

Identification and Validation of Novel Hedgehog-Responsive Enhancers Predicted by Computational Analysis of Ci/Gli Binding Site Density

Science.gov (United States)

Richards, Neil; Parker, David S.; Johnson, Lisa A.; Allen, Benjamin L.; Barolo, Scott; Gumucio, Deborah L.

2015-01-01

The Hedgehog (Hh) signaling pathway directs a multitude of cellular responses during embryogenesis and adult tissue homeostasis. Stimulation of the pathway results in activation of Hh target genes by the transcription factor Ci/Gli, which binds to specific motifs in genomic enhancers. In Drosophila, only a few enhancers (patched, decapentaplegic, wingless, stripe, knot, hairy, orthodenticle) have been shown by in vivo functional assays to depend on direct Ci/Gli regulation. All but one (orthodenticle) contain more than one Ci/Gli site, prompting us to directly test whether homotypic clustering of Ci/Gli binding sites is sufficient to define a Hh-regulated enhancer. We therefore developed a computational algorithm to identify Ci/Gli clusters that are enriched over random expectation, within a given region of the genome. Candidate genomic regions containing Ci/Gli clusters were functionally tested in chicken neural tube electroporation assays and in transgenic flies. Of the 22 Ci/Gli clusters tested, seven novel enhancers (and the previously known patched enhancer) were identified as Hh-responsive and Ci/Gli-dependent in one or both of these assays, including: Cuticular protein 100A (Cpr100A); invected (inv), which encodes an engrailed-related transcription factor expressed at the anterior/posterior wing disc boundary; roadkill (rdx), the fly homolog of vertebrate Spop; the segment polarity gene gooseberry (gsb); and two previously untested regions of the Hh receptor-encoding patched (ptc) gene. We conclude that homotypic Ci/Gli clustering is not sufficient information to ensure Hh-responsiveness; however, it can provide a clue for enhancer recognition within putative Hedgehog target gene loci. PMID:26710299

Raster Scan Computer Image Generation (CIG) System Based On Refresh Memory

Science.gov (United States)

Dichter, W.; Doris, K.; Conkling, C.

1982-06-01

A full color, Computer Image Generation (CIG) raster visual system has been developed which provides a high level of training sophistication by utilizing advanced semiconductor technology and innovative hardware and firmware techniques. Double buffered refresh memory and efficient algorithms eliminate the problem of conventional raster line ordering by allowing the generated image to be stored in a random fashion. Modular design techniques and simplified architecture provide significant advantages in reduced system cost, standardization of parts, and high reliability. The major system components are a general purpose computer to perform interfacing and data base functions; a geometric processor to define the instantaneous scene image; a display generator to convert the image to a video signal; an illumination control unit which provides final image processing; and a CRT monitor for display of the completed image. Additional optional enhancements include texture generators, increased edge and occultation capability, curved surface shading, and data base extensions.

Experimental studies of thin films deposition by magnetron sputtering method for CIGS solar cell fabrication

Science.gov (United States)

Gułkowski, Sławomir; Krawczak, Ewelina

2017-10-01

Among a variety of the thin film solar cell technologies of second generation, copper-indium-gallium-diselenide device (CIGS) with the latest highest lab cell efficiency record of 22.4 % seems to be the most promising for the power generation. This is partly due to the advantages of using low cost films of few microns thick not only as a metallic contacts but also as a main structure of the solar cell consisted of high quality semiconductor layers. This paper reports the experimental studies of the CIGS absorber formation on Soda Lime Glass substrate covered by thin molybdenum film as a back contact layer. All structures were deposited with the use of magnetron sputtering method only. Technological parameters of the deposition process such as deposition power, pressure and deposition time were optimized for each layer of the structure. Mo back contact was examined in terms of resistivity. EDS measurements were carried out to verify stoichiometric composition of CIGS absorber. Thin film of Al was used as a top contact in order to examine the quality of p-n junction. The I-V electrical characteristic of the p-n junction was analysed in terms of solar cell application.

Efficiency enhancement of CIGS compound solar cell fabricated using homomorphic thin Cr{sub 2}O{sub 3} diffusion barrier formed on stainless steel substrate

Energy Technology Data Exchange (ETDEWEB)

Sim, Jae-Kwan; Lee, Seung-Kyu; Kim, Jin-Soo; Jeong, Kwang-Un; Ahn, Haeng-Keun; Lee, Cheul-Ro, E-mail: crlee7@jbnu.ac.kr

2016-12-15

Highlights: • A chromium oxide layer is formed as diffusion barrier by thermal oxidation process on STS substrate. • A Cr{sub 2}O{sub 3} layer effectively reduces impurities diffusion into the CIGS absorber layer. • The Cr{sub 2}O{sub 3} layer plays an important role in increasing the efficiency by reduction of impurity diffusion. - Abstract: It is known that the efficiency of flexible Cu(In,Ga)Se{sub 2} (CIGS) solar cells fabricated on stainless-steel (STS) substrates deteriorates due to iron (Fe) and Cr impurities diffusing into the CIGS absorber layer. To overcome this problem, a nanoscale homomorphic chromium oxide layer was formed as a diffusion barrier by thermal oxidation on the surface of STS substrates for 1 min at 600 °C in oxygen atmosphere. By TEM and grazing-incidence X-ray diffraction (GIXRD), it was confirmed that the formed oxide layer on surface of STS substrates was a Cr{sub 2}O{sub 3} layer. It was found that the formed homomorphic Cr{sub 2}O{sub 3} thin layer of about 15 nm thickness was an effective diffusion barrier to reduce impurity diffusion into the CIGS layer by secondary ion mass spectroscopy (SIMS). In contrast to the efficiency of CIGS solar cell without homomorphic Cr{sub 2}O{sub 3} diffusion layer is 8.6%, whereas with diffusion barrier it increases to 10.6% because of impurities such as Fe and Cr from the STS substrate into the CIGS layer. It reveals that the layer formed on the surface of STS substrate by thermal oxidation process plays an important role in increasing the performance of CIGS solar cells.

Investigation of Some Transparent Metal Oxides as Damp Heat Protective Coating for CIGS Solar Cells: Preprint

Energy Technology Data Exchange (ETDEWEB)

Pern, F. J.; Yan, F.; Zaaunbrecher, B.; To, B.; Perkins, J.; Noufi, R.

2012-10-01

We investigated the protective effectiveness of some transparent metal oxides (TMO) on CIGS solar cell coupons against damp heat (DH) exposure at 85oC and 85% relative humidity (RH). Sputter-deposited bilayer ZnO (BZO) with up to 0.5-um Al-doped ZnO (AZO) layer and 0.2-um bilayer InZnO were used as 'inherent' part of device structure on CdS/CIGS/Mo/SLG. Sputter-deposited 0.2-um ZnSnO and atomic layer deposited (ALD) 0.1-um Al2O3 were used as overcoat on typical BZO/CdS/CIGS/Mo/SLG solar cells. The results were all negative -- all TMO-coated CIGS cells exhibited substantial degradation in DH. Combining the optical photographs, PL and EL imaging, SEM surface micro-morphology, coupled with XRD, I-V and QE measurements, the causes of the device degradations are attributed to hydrolytic corrosion, flaking, micro-cracking, and delamination induced by the DH moisture. Mechanical stress and decrease in crystallinity (grain size effect) could be additional degrading factors for thicker AZO grown on CdS/CIGS.

Modeling and Simulation of a Dual-Junction CIGS Solar Cell Using Silvaco ATLAS

Science.gov (United States)

2012-12-01

stage process, thermal evaporation, electrodeposition , deposition temperatures, content, stoichiometry and composition range on CIGS, inducing in...mesh. This location can be any specific region, and for the purposes of this thesis, a pair of cathode , and anode electrodes was assigned in the two...ATLASTM structure file for the dual-junction CIGS cell. In order to extract an overall I–V curve, two sets of anodes and cathodes were placed on the

Stability of CIGS Solar Cells and Component Materials Evaluated by a Step-Stress Accelerated Degradation Test Method: Preprint

Energy Technology Data Exchange (ETDEWEB)

Pern, F. J.; Noufi, R.

2012-10-01

A step-stress accelerated degradation testing (SSADT) method was employed for the first time to evaluate the stability of CuInGaSe2 (CIGS) solar cells and device component materials in four Al-framed test structures encapsulated with an edge sealant and three kinds of backsheet or moisture barrier film for moisture ingress control. The SSADT exposure used a 15oC and then a 15% relative humidity (RH) increment step, beginning from 40oC/40%RH (T/RH = 40/40) to 85oC/70%RH (85/70) as of the moment. The voluminous data acquired and processed as of total DH = 3956 h with 85/70 = 704 h produced the following results. The best CIGS solar cells in sample Set-1 with a moisture-permeable TPT backsheet showed essentially identical I-V degradation trend regardless of the Al-doped ZnO (AZO) layer thickness ranging from standard 0.12 μm to 0.50 μm on the cells. No clear 'stepwise' feature in the I-V parameter degradation curves corresponding to the SSADT T/RH/time profile was observed. Irregularity in I-V performance degradation pattern was observed with some cells showing early degradation at low T/RH < 55/55 and some showing large Voc, FF, and efficiency degradation due to increased series Rs (ohm-cm2) at T/RH ≥ 70/70. Results of (electrochemical) impedance spectroscopy (ECIS) analysis indicate degradation of the CIGS solar cells corresponded to increased series resistance Rs (ohm) and degraded parallel (minority carrier diffusion/recombination) resistance Rp, capacitance C, overall time constant Rp*C, and 'capacitor quality' factor (CPE-P), which were related to the cells? p-n junction properties. Heating at 85/70 appeared to benefit the CIGS solar cells as indicated by the largely recovered CPE-P factor. Device component materials, Mo on soda lime glass (Mo/SLG), bilayer ZnO (BZO), AlNi grid contact, and CdS/CIGS/Mo/SLG in test structures with TPT showed notable to significant degradation at T/RH ≥ 70/70. At T/RH = 85/70, substantial blistering of

Flexible CIGS solar cells on large area polymer foils with in-line deposition methods and application of alternative back contacts - Final report

Energy Technology Data Exchange (ETDEWEB)

Tiwari, A. N.

2009-08-15

This illustrated report for the Swiss Federal Office of Energy (SFOE) summarises the work performed within this project and also reports on synergies with other projects that helped to make a significant contribution to the development of CIGS thin film solar cells on flexible substrates such as polymer foils. The project's aims were to learn more about up-scaling issues and to demonstrate the abilities required for the processing of layers on large area polyimide foils for flexible CIGS solar cells. Custom-built evaporators that were designed and constructed in-house are described. A CIGS system for in-line deposition was also modified for roll-to-roll deposition and alternative electrical back contacts to conventional ones were evaluated on flexible polyimide foils. The objectives of the project and the results obtained are looked at and commented on in detail.

Experimental studies of thin films deposition by magnetron sputtering method for CIGS solar cell fabrication

Directory of Open Access Journals (Sweden)

Gułkowski Sławomir

2017-01-01

Full Text Available Among a variety of the thin film solar cell technologies of second generation, copper-indium-gallium-diselenide device (CIGS with the latest highest lab cell efficiency record of 22.4 % seems to be the most promising for the power generation. This is partly due to the advantages of using low cost films of few microns thick not only as a metallic contacts but also as a main structure of the solar cell consisted of high quality semiconductor layers. This paper reports the experimental studies of the CIGS absorber formation on Soda Lime Glass substrate covered by thin molybdenum film as a back contact layer. All structures were deposited with the use of magnetron sputtering method only. Technological parameters of the deposition process such as deposition power, pressure and deposition time were optimized for each layer of the structure. Mo back contact was examined in terms of resistivity. EDS measurements were carried out to verify stoichiometric composition of CIGS absorber. Thin film of Al was used as a top contact in order to examine the quality of p-n junction. The I-V electrical characteristic of the p-n junction was analysed in terms of solar cell application.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics.

Science.gov (United States)

Eisenberg, Daniel A; Yu, Mengjing; Lam, Carl W; Ogunseitan, Oladele A; Schoenung, Julie M

2013-09-15

Copper-indium-gallium-selenium-sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS₂ p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane. Copyright © 2013 Elsevier B.V. All rights reserved.

Nd:YAG laser annealing investigation of screen-printed CIGS layer on PET: Layer annealing method for photovoltaic cell fabrication process

KAUST Repository

Alsaggaf, Ahmed

2014-06-01

Cu(In, Ga)Se2 (CIGS) ink was formulated from CIGS powder, polyvinyl butyral PVB, terpineol and polyester/polyamine co-polymeric dispersant KD-1. Thin films with different thicknesses were deposited on PET substrate using screen-printing followed by heat treatment using a Nd:YAG laser. The structure and morphology of the heated thin films were studied. The characterization of the CIGS powder, ink, and film was done using TGA, SEM, FIB, EDS, and XRD. TGA analysis shows that the CIGS ink is drying at 200 °C, which is well below the decomposition temperature of the PET substrate. It was observed by SEM that 20 pulses of 532nm and 60 mJ/cm2 Nd:YAG laser annealing causes atomic diffusion on the near surface area. Furthermore, FIB cross section images were utilized to monitor the effect of laser annealing in the depth of the layer. Laser annealing effects were compared to as deposited layer using XRD in reference to CIGS powder. The measurement shows that crystallinity of deposited CIGS is retained while EDS quantification and atomic ratio result in gradual loss of selenium as laser energy increases. The laser parameters were tuned in an effort to utilize laser annealing of screen-printed CIGS layer as a layer annealing method for solar cell fabrication process.

Lessons learned from NMSG-085 CIG Land Operation demonstration

NARCIS (Netherlands)

Gautreau, B.; Remmersmann, T.; Henderson, H.C.; Reus, N.M. de; Khimeche, L.; Pedersen, E.; Lillesoe, J.; Liberg, D.

2013-01-01

This paper presents the experience gained during demonstrations carried out between Denmark, France, Germany, the Netherlands and Spain under the umbrella of the NMSG-085 / CIG Land Operation group. The demonstration, also presented in this paper, focuses on command post exercise training. It

Characterization and Analysis of Ultrathin CIGS Films and Solar Cells Deposited by 3-Stage Process

Directory of Open Access Journals (Sweden)

Grace Rajan

2018-01-01

Full Text Available In view of the large-scale utilization of Cu(In,GaSe2 (CIGS solar cells for photovoltaic application, it is of interest not only to enhance the conversion efficiency but also to reduce the thickness of the CIGS absorber layer in order to reduce the cost and improve the solar cell manufacturing throughput. In situ and real-time spectroscopic ellipsometry (RTSE has been used conjointly with ex situ characterizations to understand the properties of ultrathin CIGS films. This enables monitoring the growth process, analyzing the optical properties of the CIGS films during deposition, and extracting composition, film thickness, grain size, and surface roughness which can be corroborated with ex situ measurements. The fabricated devices were characterized using current voltage and quantum efficiency measurements and modeled using a 1-dimensional solar cell device simulator. An analysis of the diode parameters indicates that the efficiency of the thinnest cells was restricted not only by limited light absorption, as expected, but also by a low fill factor and open-circuit voltage, explained by an increased series resistance, reverse saturation current, and diode quality factor, associated with an increased trap density.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

International Nuclear Information System (INIS)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W.; Ogunseitan, Oladele A.; Schoenung, Julie M.

2013-01-01

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS 2 p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane

Notas sobre Feral y las cigüeñas, de Fernando Alonso, y la "Historia del califa cigüeña" (Wilhelm Hauff, Sara Cone Bryant

Directory of Open Access Journals (Sweden)

Hans Christian Hagedorn

2011-01-01

Full Text Available En el presente estudio se analizan las fuentes de la versión de la "Historia del califa cigüeña", incluida en la narración Feral y las cigüeñas (1971, de Fernando Alonso. Para ello se tienen en cuenta el cuento original del autor postromántico alemán Wilhelm Hauff ("Die Geschichte von Kalif Storch", 1825, y la adaptación de este cuento que Sara Cone Bryant realizó para su libro How to tell stories to children (1905, traducción española: El arte de contar cuentos, 1965.

CIGS Thin Film Solar Cells, phase 2 Uppsala University Final report 2006-01-01 - 2007-06-14

Energy Technology Data Exchange (ETDEWEB)

Edoff, Marika (Thin Film Solar Cell group, Dep. Technical Sciences, Uppsala Univ., P.O. Box 534, SE-751 21 Uppsala (Sweden)) (and others)

2007-06-15

The project CIGS Thin Film Solar Cells, phase 2 has been going on for 18,5 months and was interrupted in advance on the 14th of June, 2007. The decision to shorten the period was taken by the board of the Swedish Energy Agency the 14th of February. It was decided to reevaluate and re-direct the financial support to the group. A new project, CIGS Thin Film Solar Cells, phase 3, superseded this project and will go on for the initially planned project period (until 2009-12-31). During the project much of the focus has been on research on Cd-free buffer layers, with an emphasis on the interface properties between the CIGS and the buffer layer. (CIGS is a commonly used acronym for Cu(In,Ga)Se{sub 2}, which is the active absorption layer in this type of solar cells) The combination of high quality CIGS and the new buffer layers has been another field of interest. CIGS solar cell module development and computer modelling of solar cells and modules has been the third major research area. The results show that the group still holds a position as one of the leaders in the world in this field. The 18.5 % efficient Cd-free solar cell, which was obtained and independently confirmed is only one percent away from the world record and in addition it is Cd-free using a Zn(O,S) buffer layer (the world record from NREL contains Cd). By alloying ZnO with MgO instead of ZnS almost equally good results can be achieved. During the last half year an 18.1 % cell has been measured with a (Zn,Mg)O buffer layer. Solar cell module technology includes several research issues, both fundamental as e.g. modelling of cell voltage and losses as a function of distance from interconnect to interconnect, but also more development as e.g. encapsulation routines. The harsh environment test (damp heat test) run at 85 deg C and 85 % relative humidity for 1000 hours was passed for both a small (12.5x12.5 cm2) and a large (27.5x30 cm2) module within the degradation limits stated by the IEC standards, using

Competitive-IgY- Enzyme Linked Immuno Sorbent Assay (CIgY-ELISA to detect the cytokinins in Gerbera jamesonii plantlets

Directory of Open Access Journals (Sweden)

Cleiton Mateus Sousa

2011-08-01

Full Text Available A competitive hyper-immune yolk Immunoglobulin Y - Enzyme Linked Immune Sorbent Assay (CIgY-ELISA, was developed as an alternative method to detect zeatin and 2ip in plantlets of gerbera. The endogenous level of hormones in the plantlets in vitro of gerbera with one or six weeks after replication was determined with competitive IgY-ELISA set to detect between 1 and 100 pmoles of plant hormone for each 1.0 g tissue. The plantlets of six weeks presented sprouts and root, while the plantlets of one week presented only sprouts. The CIgY-ELISA was set with high independent variables values of sensitivity/specificity of 96/89 % for zeatin and 94/78 % for 2ip, with high values of reproducibility (up to 90 % for both the cytokinins. Zeatin content varied from 2.2 to 2.8 pmoles.g-1 and from 2.7 to 3.3 pmoles.g-1 on the plantlet with one and six weeks, respectively. The 2ip content did not vary and was detected near the detection limit in all the assays. It was concluded that the observed capabilities of CIgY-ELISA were putative and the competitive assay was a highly robust and stable method, which could be used for the studies on plant physiology for endogenous cytokinins.

Improving Efficiency of Multicrystalline Silicon and CIGS Solar Cells by Incorporating Metal Nanoparticles

Directory of Open Access Journals (Sweden)

Ming-Jer Jeng

2015-10-01

Full Text Available This work studies the use of gold (Au and silver (Ag nanoparticles in multicrystalline silicon (mc-Si and copper-indium-gallium-diselenide (CIGS solar cells. Au and Ag nanoparticles are deposited by spin-coating method, which is a simple and low cost process. The random distribution of nanoparticles by spin coating broadens the resonance wavelength of the transmittance. This broadening favors solar cell applications. Metal shadowing competes with light scattering in a manner that varies with nanoparticle concentration. Experimental results reveal that the mc-Si solar cells that incorporate Au nanoparticles outperform those with Ag nanoparticles. The incorporation of suitable concentration of Au and Ag nanoparticles into mc-Si solar cells increases their efficiency enhancement by 5.6% and 4.8%, respectively. Incorporating Au and Ag nanoparticles into CIGS solar cells improve their efficiency enhancement by 1.2% and 1.4%, respectively. The enhancement of the photocurrent in mc-Si solar cells is lower than that in CIGS solar cells, owing to their different light scattering behaviors and material absorption coefficients.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W. [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States); Ogunseitan, Oladele A. [University of California, Irvine, Irvine, CA 92697 (United States); Schoenung, Julie M., E-mail: jmschoenung@ucdavis.edu [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States)

2013-09-15

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS{sub 2} p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane.

Thermal Effect on a CIGS Thin-Film Solar Cell P2 Layer by Using a UV Laser

Directory of Open Access Journals (Sweden)

Dyi-Cheng Chen

2014-07-01

Full Text Available This study used ANSYS simulation software for analyzing an ultraviolet (UV (355 nm laser processing system. The laser apparatus was used in a stainless steel CIGS solar cell P2 layer for simulation analysis. CIGS films process order according to SiO2 layer, molybdenum electrode, CIGS absorbed layer, CdS buffered layer, i-ZnO penetrate light layer, TCO front electrode, MgF resist reflected materials, andelectrode materials. The simulation and experimental results were compared to obtain a laser-delineated P2 laser with a low melting and vaporization temperature. According to the simulation results, the laser function time was 135 μs, the UV laser was 0.5 W, and the P2 layer thin films were removed. The experimental results indicated that the electrode pattern of the experiment was similar to that of the simulation result, and the laser process did not damage the base plate. The analysis results confirm that the laser apparatus is effective when applied to a stainless steel CIGS solar cell P2 layer.

Comparative study of the role of Ga in CIGS solar cells with different thickness

Energy Technology Data Exchange (ETDEWEB)

Han, Anjun, E-mail: haj211@mail.sim.ac.cn [Institute of Photo Electronics Thin Film Devices and Technique of Nankai University, Tianjin 300071 (China); Research Center for New Energy Technology, Shanghai Institute of Microsystem and Information Technology (SIMIT), Chinese Academy of Sciences (CAS), 235 Chengbei Road, Jiading, Shanghai 201800 (China); Sun, Yun; Zhang, Yi [Institute of Photo Electronics Thin Film Devices and Technique of Nankai University, Tianjin 300071 (China); Liu, Xiaohui; Meng, Fanying; Liu, Zhengxin [Research Center for New Energy Technology, Shanghai Institute of Microsystem and Information Technology (SIMIT), Chinese Academy of Sciences (CAS), 235 Chengbei Road, Jiading, Shanghai 201800 (China)

2016-01-01

Cu(In, Ga)Se{sub 2} (CIGS) thin films with thickness of 1 μm and 2 μm are prepared by co-evaporation process, and the different Ga/(Ga + In) are achieved by varying the temperature of Ga source. The morphology, structure, minimum band gap, and performance of solar cells are comparatively studied. As Ga/(Ga + In) increases, little changes can be observed in the crystal quality of 1 μm CIGS films, while the grain size of 2 μm films decreases significantly. (112) diffraction peak intensities of the 1 μm and 2 μm films decrease and increase, respectively. In the case of the same Ga/(Ga + In), the minimum band gap values of 1 μm films are larger than that of 2 μm films, and the difference becomes large with Ga/(Ga + In) increasing. The minimum band gap values of 1 μm films are more sensitive to variation of the Ga/(Ga + In). As Ga/(Ga + In) increases, a more improvement of the efficiency of solar cells with thickness of 1 μm is obtained due to the large enhancement of the open-circuit voltage, and the efficiency reaches the maximum value when Ga/(Ga + In) is about 0.37. - Highlights: • The role of Ga in CIGS solar cells with different thickness is comparatively studied. • Effect of Ga on the material properties of 1 μm and 2 μm films is totally different. • The minimum band gap of thinned films is more sensitive to variation of Ga/(Ga + In). • Efficiency of thinned solar cells increases more significantly with Ga increasing.

Semi-transparent perovskite solar cells for tandems with silicon and CIGS

KAUST Repository

Bailie, Colin D.; Christoforo, M. Greyson; Mailoa, Jonathan P.; Bowring, Andrea R.; Unger, Eva L.; Nguyen, William H.; Burschka, Julian; Pellet, Norman; Lee, Jungwoo Z.; Grä tzel, Michael; Noufi, Rommel; Buonassisi, Tonio; Salleo, Alberto; McGehee, Michael D.

2015-01-01

solar cell. We use a transparent silver nanowire electrode on perovskite solar cells to achieve a semi-transparent device. We place the semi-transparent cell in a mechanically-stacked tandem configuration onto copper indium gallium diselenide (CIGS

Monolithic two-terminal hybrid a-Si:H/CIGS tandem cells

NARCIS (Netherlands)

Blanker, J.; Vroon, Z.; Zeman, M.; Smets, A.

2016-01-01

Copper-indium-gallium-di-selenide (CIGS) is the present record holder in lab-scale thin-film photovoltaics (TFPV). One of the problems of this PV technology is the scarcity of indium. Multi-junction solar cells allow better spectral utilization of the light spectrum, while the required current

Ecotoxicological assessment of solar cell leachates: Copper indium gallium selenide (CIGS) cells show higher activity than organic photovoltaic (OPV) cells

Energy Technology Data Exchange (ETDEWEB)

Brun, Nadja Rebecca [University of Applied Sciences and Arts Northwestern Switzerland, School of Life Sciences, Gründenstrasse 40, CH-4132 Muttenz (Switzerland); Institute of Biogeochemistry and Pollutant Dynamics, ETH Zurich, Universitätsstrasse 16, CH-8092 Zürich (Switzerland); Wehrli, Bernhard [Institute of Biogeochemistry and Pollutant Dynamics, ETH Zurich, Universitätsstrasse 16, CH-8092 Zürich (Switzerland); Fent, Karl, E-mail: karl.fent@fhnw.ch [University of Applied Sciences and Arts Northwestern Switzerland, School of Life Sciences, Gründenstrasse 40, CH-4132 Muttenz (Switzerland); Institute of Biogeochemistry and Pollutant Dynamics, ETH Zurich, Universitätsstrasse 16, CH-8092 Zürich (Switzerland)

2016-02-01

Despite the increasing use of photovoltaics their potential environmental risks are poorly understood. Here, we compared ecotoxicological effects of two thin-film photovoltaics: established copper indium gallium selenide (CIGS) and organic photovoltaic (OPV) cells. Leachates were produced by exposing photovoltaics to UV light, physical damage, and exposure to environmentally relevant model waters, representing mesotrophic lake water, acidic rain, and seawater. CIGS cell leachates contained 583 μg L{sup −1} molybdenum at lake water, whereas at acidic rain and seawater conditions, iron, copper, zinc, molybdenum, cadmium, silver, and tin were present up to 7219 μg L{sup −1}. From OPV, copper (14 μg L{sup −1}), zinc (87 μg L{sup −1}) and silver (78 μg L{sup −1}) leached. Zebrafish embryos were exposed until 120 h post-fertilization to these extracts. CIGS leachates produced under acidic rain, as well as CIGS and OPV leachates produced under seawater conditions resulted in a marked hatching delay and increase in heart edema. Depending on model water and solar cell, transcriptional alterations occurred in genes involved in oxidative stress (cat), hormonal activity (vtg1, ar), metallothionein (mt2), ER stress (bip, chop), and apoptosis (casp9). The effects were dependent on the concentrations of cationic metals in leachates. Addition of ethylenediaminetetraacetic acid protected zebrafish embryos from morphological and molecular effects. Our study suggests that metals leaching from damaged CIGS cells, may pose a potential environmental risk. - Highlights: • Photovoltaics may be disposed in the environment after usage. • Copper indium gallium selenide (CIGS) and organic (OPV) cells were compared. • Morphological and molecular effects were assessed in zebrafish embryos. • Environmental condition affected metal leaching and ecotoxicological activity. • Damaged CIGS cells pose higher risk to the environment than OPV cells.

Daily users compared to less frequent users find vape as or more satisfying and less dangerous than cigarettes, and are likelier to use non-cig-alike vaping products.

Science.gov (United States)

Kozlowski, Lynn T; Homish, D Lynn; Homish, Gregory G

2017-06-01

We assessed the roles of perceived satisfaction and perceived danger and vaping-product-type as correlates of more frequent use of vaping products. In a baseline assessment of a longitudinal study of US Army Reserve/National Guard Soldiers and their partners (New York State, USA, 2014-2016), participants were asked about current use of vaping products (e-cigarettes) and perceived satisfaction and danger in comparison to cigarettes as well as type of product used. Fisher-exact tests and multiple ordinal logistic regressions were used. In multivariable and univariate models, more perceived satisfaction, less perceived danger, and use of non-cig-alike products were associated with more frequent use of vaping products ( p s < 0.05, two-tailed). For self-selected, more frequent adult users, e-cigs can be at least as satisfying as cigarettes and often more satisfying and are perceived as less dangerous than cigarettes. Non-cig-alike products were more likely in daily users. Some concern that e-cigs are a gateway to cigarettes arises from assuming that e-cigs may not be as reinforcing and pleasurable as cigarettes. These results indicate that accurate perception of comparative risk and use of more effective-nicotine delivery product can produce for some users a highly-satisfying alternative to cigarettes.

Daily users compared to less frequent users find vape as or more satisfying and less dangerous than cigarettes, and are likelier to use non-cig-alike vaping products

Directory of Open Access Journals (Sweden)

Lynn T. Kozlowski

2017-06-01

Full Text Available We assessed the roles of perceived satisfaction and perceived danger and vaping-product-type as correlates of more frequent use of vaping products. In a baseline assessment of a longitudinal study of US Army Reserve/National Guard Soldiers and their partners (New York State, USA, 2014–2016, participants were asked about current use of vaping products (e-cigarettes and perceived satisfaction and danger in comparison to cigarettes as well as type of product used. Fisher-exact tests and multiple ordinal logistic regressions were used. In multivariable and univariate models, more perceived satisfaction, less perceived danger, and use of non-cig-alike products were associated with more frequent use of vaping products (ps < 0.05, two-tailed. For self-selected, more frequent adult users, e-cigs can be at least as satisfying as cigarettes and often more satisfying and are perceived as less dangerous than cigarettes. Non-cig-alike products were more likely in daily users. Some concern that e-cigs are a gateway to cigarettes arises from assuming that e-cigs may not be as reinforcing and pleasurable as cigarettes. These results indicate that accurate perception of comparative risk and use of more effective-nicotine delivery product can produce for some users a highly-satisfying alternative to cigarettes.

A study on the optics of copper indium gallium (di)selenide (CIGS) solar cells with ultra-thin absorber layers

NARCIS (Netherlands)

Xu, M.; Wachters, A.J.H.; Van Deelen, J.; Mourad, M.C.D.; Buskens, P.J.P.

2014-01-01

We present a systematic study of the effect of variation of the zinc oxide (ZnO) and copper indium gallium (di)selenide (CIGS) layer thickness on the absorption characteristics of CIGS solar cells using a simulation program based on finite element method (FEM). We show that the absorption in the

Electrodeposition route to synthesize cigs films – an economical way ...

African Journals Online (AJOL)

Electrodeposition route to synthesize cigs films – an economical way to harness solar energy. ... for solar cells, how the charge separation in this nano scale photovoltaic (PV) materials occurs which help in absorption of radiation, and the electro-deposition route, a low cost one, produces thin film solar cells are analyzed.

Improving Performance of CIGS Solar Cells by Annealing ITO Thin Films Electrodes

Directory of Open Access Journals (Sweden)

Chuan Lung Chuang

2015-01-01

Full Text Available Indium tin oxide (ITO thin films were grown on glass substrates by direct current (DC reactive magnetron sputtering at room temperature. Annealing at the optimal temperature can considerably improve the composition, structure, optical properties, and electrical properties of the ITO film. An ITO sample with a favorable crystalline structure was obtained by annealing in fixed oxygen/argon ratio of 0.03 at 400°C for 30 min. The carrier concentration, mobility, resistivity, band gap, transmission in the visible-light region, and transmission in the near-IR regions of the ITO sample were -1.6E+20 cm−3, 2.7E+01 cm2/Vs, 1.4E-03 Ohm-cm, 3.2 eV, 89.1%, and 94.7%, respectively. Thus, annealing improved the average transmissions (400–1200 nm of the ITO film by 16.36%. Moreover, annealing a copper-indium-gallium-diselenide (CIGS solar cell at 400°C for 30 min in air improved its efficiency by 18.75%. The characteristics of annealing ITO films importantly affect the structural, morphological, electrical, and optical properties of ITO films that are used in solar cells.

BADANIA NAD TECHNOLOGIĄ OTRZYMYWANIA CIENKICH WARSTW EMITERA METODĄ ROZPYLANIA MAGNETRONOWEGO DLA ZASTOSOWAŃ W OGNIWACH CIGS

Directory of Open Access Journals (Sweden)

Justyna PIETRASZEK

Full Text Available Cienkowarstwowe ogniwa fotowoltaiczne wykonane na bazie struktury CIGS (mieszaniny pierwiastków miedzi, indu, galu oraz selenu należą do II generacji ogniw fotowoltaicznych. Wykazują one efektywność na poziomie zbliżonym do ogniw I generacji, lecz ze względu na niższe zużycie materiału, coraz częściej wypierają z rynku ogniwa krzemowe Artykuł przedstawia rezultaty badań dotyczących sposobu otrzymywania warstwy buforowej CdS (siarczku kadmu, zastosowanej w cienkowarstwowych ogniwach fotowoltaicznych typu CIGS. Przyjęto dwa rozwiązania technologii nanoszenia: warstwa okna CdS uzyskana metodą rozpylenia magnetronowego oraz warstwa okna CdS uzyskana metodą kąpieli chemicznej (CBD– Chemical Bath Deposition. Struktura ta powinna posiadać odpowiednią wielkość przerwy energetycznej, która pozwali na większą absorpcję fotonów, a także wymaga się, aby była cienka (mniej niż 100 nm i jednolita. Warstwy CdS zostały nałożone przez osadzanie w kąpieli chemicznej CBD na szklanych podłożach pokrytych Mo/CIGS (naniesione warstwy metodą sputteringu magnetronowego. Uzyskano dzięki temu warstwę emitera o grubości 80 nm po czasie osadzania 35 minut. Dla porównania warstwy CdS zostały nałożone poprzez sputtering magnetronowy na podłożu Mo/CIGS, uzyskanym tą samą metodą. Następnie oba rozwiązania zostały przebadane pod względem morfologii powierzchni na elektronowym mikroskopie skaningowym, jak również przeprowadzono analizy składu pierwiastkowego warstw. Zarówno jedna, jak i druga metoda prowadzi do otrzymania warstwy emitera CdS dla zastosowań w ogniwach CIGS.

Optical Design of Textured Thin-Film CIGS Solar Cells with Nearly-Invisible Nanowire Assisted Front Contacts

Directory of Open Access Journals (Sweden)

Joop van Deelen

2017-04-01

Full Text Available The conductivity of transparent front contacts can be improved by patterned metallic nanowires, albeit at the cost of optical loss. The associated optical penalty can be strongly reduced by texturization of the cell stack. Remarkably, the nanowires themselves are not textured and not covered in our design. This was shown by optical modeling where the width of the nanowire, the texture height and the texture period were varied in order to obtain a good insight into the general trends. The optical performance can be improved dramatically as the reflection, which is the largest optical loss, can be reduced by 95% of the original value. The spectra reveal absorption in the Cu(In,GaSe2 (CIGS layer of 95% and reflection below 2% over a large part of the spectrum. In essence, a virtually black CIGS cell stack can be achieved for textured cells with a metal nanogrid. Moreover, it turned out that the ratio between the width of the nanowire and the height of the texture is a critical parameter for optical losses.

Nd:YAG laser annealing investigation of screen-printed CIGS layer on PET: Layer annealing method for photovoltaic cell fabrication process

KAUST Repository

Alsaggaf, Ahmed; Alarousu, Erkki; Boulfrad, Samir; Rothenberger, Alexander

2014-01-01

by heat treatment using a Nd:YAG laser. The structure and morphology of the heated thin films were studied. The characterization of the CIGS powder, ink, and film was done using TGA, SEM, FIB, EDS, and XRD. TGA analysis shows that the CIGS ink is drying

Surface microstructure evolution of highly transparent and conductive Al-doped ZnO thin films and its application in CIGS solar cells

Science.gov (United States)

Cheng, Ke; Liu, Jingjing; Jin, Ranran; Liu, Jingling; Liu, Xinsheng; Lu, Zhangbo; Liu, Ya; Liu, Xiaolan; Du, Zuliang

2017-07-01

Aluminum-doped zinc oxide (AZO) has attained intensive attention as being a very good transparent conducting oxide for photovoltaic applications. In this work, AZO films have been deposited on glass substrate by radio frequency (RF) magnetron sputtering. The influences of substrate temperatures on morphological, structural, optical and electrical properties of AZO films were systematically investigated. The results indicate that all AZO films have the hexagonal structure with c-axis preferred orientation. Morphological and electrical measurements have revealed that the substrate temperatures have strong influence on the microstructure, optical and electrical properties of AZO films. The AZO film is highly transparent from ultraviolet up to near infrared range with highest average transparency exceeding 83%. The minimum resistivity is as low as 6.1 × 10-4 Ω cm. The carrier concentration and mobility are as high as 3.357 × 1020 cm-3 and 30.48 cm2/Vs, respectively. Finally, the performances of the AZO film are evaluated by its practical application in Cu(In1-xGax)Se2 (CIGS) photovoltaic device as a transparent electrode. Benefited from its highly transparent and conductive feature, the most efficient device reveals an efficiency of 7.8% with a short-circuit current density of 28.99 mA/cm2, an open-circuit voltage of 430 mV, and a fill factor of 62.44 under standard conditions.

Controlling the physical parameters of crystalline CIGS nanowires for use in superstrate configuration using vapor phase epitaxy

Science.gov (United States)

Lee, Dongjin; Jeon, H. C.; Kang, T. W.; Kumar, Sunil

2018-03-01

Indium tin oxide (ITO) is a suitable candidate for smart windows and bifacial semi-transparent solar cell applications. In this study, highly crystalline CuInGaSe2 (CIGS) nanowires were successfully grown by horizontal-type vapor phase epitaxy on an ITO substrate. Length, diameter, and density of the nanowires were studied by varying the growth temperature (500, 520, and 560 °C), time (3.5, 6.5, and 9.5 h), and type of catalyst (In, Au, and Ga). Length, diameter, and density of the nanowires were found to be highly dependent on the growth conditions. At an optimized growth period and temperature of 3.5 h and 520 °C, respectively, the length and diameter of the nanowires were found to increase when grown in a catalyst-free environment. However, the density of the nanowires was found to be higher while using a catalyst during growth. Even in a catalyst-free environment, an Indium cluster formed at the bottom of the nanowires. The source of these nanowires is believed to be Indium from the ITO substrate which was observed in the EDS measurement. TEM-based EDS and line EDS indicated that the nanowires are made up of CIGS material with a very low Gallium content. XRD measurements also show the appearance of wurtzite CIS nanowires grown on ITO in addition to the chalcopyrite phase. PL spectroscopy was done to see the near-band-edge emission for finding band-to-band optical transition in this material. Optical response of the CIGS nanowire network was also studied to see the photovoltaic effect. This work creates opportunities for making real solar cell devices in superstrate configuration.

Survey of CIG Data Base Generation from Imagery.

Science.gov (United States)

1980-09-01

200, February 1980. McGrath, J., "The Use of Wide-Angle Cinematic Simulators in Pilot Training", Technical Report NAVTRAEQUIPCEN 70-C-0306-1, March 1973... March 1974. 5 NAVTRAEQUIPCEN IH-318 algorithms which utilize data bases in which the inf)rmation is stored as planar polygons. In currint, real-time CIG...Vision Simulation and Motion Conference, April 1976. 42McGrath, J., "The Use of Wide-Angle Cinematic Simulators in Pilot Training", Technical Report

CIGS J-V distortion in the absence of blue photons

International Nuclear Information System (INIS)

Pudov, A.O.; Sites, J.R.; Contreras, M.A.; Nakada, T.; Schock, H.-W.

2005-01-01

Common buffer materials used with CuInGaSe 2 (CIGS) absorbers produce conduction-band barriers that may significantly distort the current-voltage (J-V) curves, especially when short-wavelength photons are excluded from the illumination spectrum. Earlier work documented this effect for CuInSe 2 (CIS) absorbers (band gap near 1.0 eV) with CdS buffers. Higher band-gap (no. approxno. 1.15 eV) CIGS absorbers show little or no distortion with CdS buffer layers. However, wider band gap (lower electron affinity) ZnS(O,OH) or InS(O,OH) buffers, prepared by chemical-bath deposition (CBD), clearly show the J-V distortion. The distortions have a turn-on time constant the order of a minute and turn-off time constant the order of a day, and they correlate with major variations in apparent quantum efficiency (QE) measured with varying intensity and spectral content of bias light. The results are consistent with a conduction-band spike barrier that increases with buffer band gap and is larger when the electron concentration in the buffer is small

Modelling Defects Acceptors And Determination Of Electric Model From The Nyquist Plot And Bode In Thin Film CIGS

Directory of Open Access Journals (Sweden)

Demba Diallo

2015-08-01

Full Text Available Abstract The performance of the chalcopyrite material CuInGaSe2 CIGS used as an absorber layer in thin-film photovoltaic devices is significantly affected by the presence of native defects. Multivalent defects e.g. double acceptors or simple acceptor are important immaterial used in solar cell production in general and in chalcopyrite materials in particular. We used the thin film solar cell simulation software SCAPS to enable the simulation of multivalent defects with up to five different charge states.Algorithms enabled us to simulate an arbitrary number of possible states of load. The presented solution method avoids numerical inaccuracies caused by the subtraction of two almost equal numbers. This new modelling facility is afterwards used to investigate the consequences of the multivalent character of defects for the simulation of chalcopyrite based CIGS. The capacitance increase with the evolution of the number of defects C- f curves have found to have defect dependence.

Materials Characterization of CIGS solar cells on Top of CMOS chips

NARCIS (Netherlands)

Lu, J.; Liu, W.; Kovalgin, A.Y.; Sun, Y.; Schmitz, J.; Venkatasubramanian, R.; Radousky, H.; Liang, H.

2011-01-01

In the current work, we present a detailed study on the material properties of the CIGS layers, fabricated on top of the CMOS chips, and compare the results with the fabrication on standard glass substrates. Almost identical elemental composition on both glass and CMOS chips (within measurement

Quenching Mo optical losses in CIGS solar cells by a point contacted dual-layer dielectric spacer: a 3-D optical study

NARCIS (Netherlands)

Rezaei, N.; Isabella, O.; Vroon, Z.; Zeman, M.

2018-01-01

A 3-D optical modelling was calibrated to calculate the light absorption and the total reflection of fabricated CIGS solar cells. Absorption losses at molybdenum (Mo) / CIGS interface were explained in terms of plasmonic waves. To quench these losses, we assumed the insertion of a lossless

Quenching Mo optical losses in CIGS solar cells by a point contacted dual-layer dielectric spacer : A 3-D optical study

NARCIS (Netherlands)

Rezaei, N.; Isabella, O.; Vroon, Zeger; Zeman, M.

2018-01-01

A 3-D optical modelling was calibrated to calculate the light absorption and the total reflection of fabricated CIGS solar cells. Absorption losses at molybdenum (Mo) / CIGS interface were explained in terms of plasmonic waves. To quench these losses, we assumed the insertion of a lossless

CIGS cells with metallized front contact: Longer cells and higher efficiency

NARCIS (Netherlands)

Deelen, J. van; Frijters, C.

2017-01-01

We have investigated the benefit of a patterned metallization on top of a transparent conductive oxide in CIGS thin-film solar panels. It was found that cells with a grid have a higher efficiency compared to cells with only a TCO. This was observed for all cell lengths used. Furthermore, metallic

Ecotoxicological assessment of solar cell leachates: Copper indium gallium selenide (CIGS) cells show higher activity than organic photovoltaic (OPV) cells.

Science.gov (United States)

Brun, Nadja Rebecca; Wehrli, Bernhard; Fent, Karl

2016-02-01

Despite the increasing use of photovoltaics their potential environmental risks are poorly understood. Here, we compared ecotoxicological effects of two thin-film photovoltaics: established copper indium gallium selenide (CIGS) and organic photovoltaic (OPV) cells. Leachates were produced by exposing photovoltaics to UV light, physical damage, and exposure to environmentally relevant model waters, representing mesotrophic lake water, acidic rain, and seawater. CIGS cell leachates contained 583 μg L(-1) molybdenum at lake water, whereas at acidic rain and seawater conditions, iron, copper, zinc, molybdenum, cadmium, silver, and tin were present up to 7219 μg L(-1). From OPV, copper (14 μg L(-1)), zinc (87 μg L(-1)) and silver (78 μg L(-1)) leached. Zebrafish embryos were exposed until 120 h post-fertilization to these extracts. CIGS leachates produced under acidic rain, as well as CIGS and OPV leachates produced under seawater conditions resulted in a marked hatching delay and increase in heart edema. Depending on model water and solar cell, transcriptional alterations occurred in genes involved in oxidative stress (cat), hormonal activity (vtg1, ar), metallothionein (mt2), ER stress (bip, chop), and apoptosis (casp9). The effects were dependent on the concentrations of cationic metals in leachates. Addition of ethylenediaminetetraacetic acid protected zebrafish embryos from morphological and molecular effects. Our study suggests that metals leaching from damaged CIGS cells, may pose a potential environmental risk. Copyright © 2015 Elsevier B.V. All rights reserved.

Above-CMOS a-Si and CIGS Solar Cells for Powering Autonomous Microsystems

NARCIS (Netherlands)

Lu, J.; Liu, W.; van der Werf, C.H.M.; Kovalgin, A.Y.; Sun, Y.; Schropp, R.E.I.; Schmitz, J.

2010-01-01

Two types of solar cells are successfully grown on chips from two CMOS generations. The efficiency of amorphous-silicon (a-Si) solar cells reaches 5.2%, copperindium-gallium-selenide (CIGS) cells 7.1%. CMOS functionality is unaffected. The main integration issues: adhesion, surface topography, metal

CIG-DB: the database for human or mouse immunoglobulin and T cell receptor genes available for cancer studies

Directory of Open Access Journals (Sweden)

Furue Motoki

2010-07-01

Full Text Available Abstract Background Immunoglobulin (IG or antibody and the T-cell receptor (TR are pivotal proteins in the immune system of higher organisms. In cancer immunotherapy, the immune responses mediated by tumor-epitope-binding IG or TR play important roles in anticancer effects. Although there are public databases specific for immunological genes, their contents have not been associated with clinical studies. Therefore, we developed an integrated database of IG/TR data reported in cancer studies (the Cancer-related Immunological Gene Database [CIG-DB]. Description This database is designed as a platform to explore public human and murine IG/TR genes sequenced in cancer studies. A total of 38,308 annotation entries for IG/TR proteins were collected from GenBank/DDBJ/EMBL and the Protein Data Bank, and 2,740 non-redundant corresponding MEDLINE references were appended. Next, we filtered the MEDLINE texts by MeSH terms, titles, and abstracts containing keywords related to cancer. After we performed a manual check, we classified the protein entries into two groups: 611 on cancer therapy (Group I and 1,470 on hematological tumors (Group II. Thus, a total of 2,081 cancer-related IG and TR entries were tabularized. To effectively classify future entries, we developed a computational method based on text mining and canonical discriminant analysis by parsing MeSH/title/abstract words. We performed a leave-one-out cross validation for the method, which showed high accuracy rates: 94.6% for IG references and 94.7% for TR references. We also collected 920 epitope sequences bound with IG/TR. The CIG-DB is equipped with search engines for amino acid sequences and MEDLINE references, sequence analysis tools, and a 3D viewer. This database is accessible without charge or registration at http://www.scchr-cigdb.jp/, and the search results are freely downloadable. Conclusions The CIG-DB serves as a bridge between immunological gene data and cancer studies, presenting

Confinement - assisted shock-wave-induced thin-film delamination (SWIFD) of copper indium gallium diselenide (CIGS) on a flexible substrate

Science.gov (United States)

Lorenz, Pierre; Zagoranskiy, Igor; Ehrhardt, Martin; Han, Bing; Bayer, Lukas; Zimmer, Klaus

2017-12-01

The laser structuring of CIGS (copper indium gallium (di)selenide) solar cell material without influence and damaging the functionality of the active layer is a challenge for laser methods The shock-wave-induced thin-film delamination (SWIFD) process allows structuring without thermal modifications due to a spatial separation of the laser absorption from the functional layer removal process. In the present study, SWIFD structuring of CIGS solar cell stacks was investigated. The rear side of the polyimide was irradiated with a KrF-Excimer laser. The laser-induced ablation process generates a traverse shock wave, and the interaction of the shock wave with the layer-substrate interface results in a delamination process. The effect of a water confinement on the SWIFD process was studied where the rear side of the substrate was covered with a ∼2 mm thick water layer. The resultant surface morphology was analysed and discussed. At a sufficient number of laser pulses N and laser fluences Φ, the CIGS layer can be selectively removed from the Mo back contact. The water confinement, as well as the increasing laser beam size A0 and N, results in the reduction of the necessary minimal laser fluence Φth. Further, the delaminated CIGS area increased with increasing Φ, N, and A0.

Photovoltaic Performance and Interface Behaviors of Cu(In,Ga)Se2 Solar Cells with a Sputtered-Zn(O,S) Buffer Layer by High-Temperature Annealing.

Science.gov (United States)

Wi, Jae-Hyung; Kim, Tae Gun; Kim, Jeong Won; Lee, Woo-Jung; Cho, Dae-Hyung; Han, Won Seok; Chung, Yong-Duck

2015-08-12

We selected a sputtered-Zn(O,S) film as a buffer material and fabricated a Cu(In,Ga)Se2 (CIGS) solar cell for use in monolithic tandem solar cells. A thermally stable buffer layer was required because it should withstand heat treatment during processing of top cell. Postannealing treatment was performed on a CIGS solar cell in vacuum at temperatures from 300-500 °C to examine its thermal stability. Serious device degradation particularly in VOC was observed, which was due to the diffusion of thermally activated constituent elements. The elements In and Ga tend to out-diffuse to the top surface of the CIGS, while Zn diffuses into the interface of Zn(O,S)/CIGS. Such rearrangement of atomic fractions modifies the local energy band gap and band alignment at the interface. The notch-shape induced at the interface after postannealing could function as an electrical trap during electron transport, which would result in the reduction of solar cell efficiency.

Photovoltaic characterization of Copper-Indium-Gallium Sulfide (CIGS2) solar cells for lower absorber thicknesses

Energy Technology Data Exchange (ETDEWEB)

Vasekar, Parag S., E-mail: psvasekar@yahoo.co [Florida Solar Energy Center, 1679 Clearlake Rd., Cocoa FL, 32922 (United States); Jahagirdar, Anant H.; Dhere, Neelkanth G. [Florida Solar Energy Center, 1679 Clearlake Rd., Cocoa FL, 32922 (United States)

2010-01-31

Chalcopyrites are important contenders among thin-film solar cells due to their direct band gap and higher absorption coefficient. Copper-Indium-Gallium Sulfide (CIGS2) is a chalcopyrite material with a near-optimum band gap of {approx} 1.5 eV. Record efficiency of 11.99% has been achieved on a 2.7 {mu}m CIGS2 film prepared by sulfurization at the Florida Solar Energy Center (FSEC) PV Materials Lab. In this work, photovoltaic performance analysis has been carried out for a 1.5 {mu}m absorber prepared under similar conditions as that of a 2.7 {mu}m thick absorber sample. It was observed that there is an increase in diode factor and reverse saturation current density when the absorber thickness was decreased. The diode factor increased from 1.69 to 2.18 and reverse saturation current density increased from 1.04 x 10{sup -10} mA/cm{sup 2} to 1.78 x 10{sup -8} mA/cm{sup 2}. This can be attributed to a decrease in the grain size when the absorber thickness is decreased. It was also observed that there is an improvement in the shunt resistance. Improvement in shunt resistance can be attributed to optimized value of i:ZnO for lower absorber thickness and less shunting paths due to a smoother absorber.

Photovoltaic characterization of Copper-Indium-Gallium Sulfide (CIGS2) solar cells for lower absorber thicknesses

International Nuclear Information System (INIS)

Vasekar, Parag S.; Jahagirdar, Anant H.; Dhere, Neelkanth G.

2010-01-01

Chalcopyrites are important contenders among thin-film solar cells due to their direct band gap and higher absorption coefficient. Copper-Indium-Gallium Sulfide (CIGS2) is a chalcopyrite material with a near-optimum band gap of ∼ 1.5 eV. Record efficiency of 11.99% has been achieved on a 2.7 μm CIGS2 film prepared by sulfurization at the Florida Solar Energy Center (FSEC) PV Materials Lab. In this work, photovoltaic performance analysis has been carried out for a 1.5 μm absorber prepared under similar conditions as that of a 2.7 μm thick absorber sample. It was observed that there is an increase in diode factor and reverse saturation current density when the absorber thickness was decreased. The diode factor increased from 1.69 to 2.18 and reverse saturation current density increased from 1.04 x 10 -10 mA/cm 2 to 1.78 x 10 -8 mA/cm 2 . This can be attributed to a decrease in the grain size when the absorber thickness is decreased. It was also observed that there is an improvement in the shunt resistance. Improvement in shunt resistance can be attributed to optimized value of i:ZnO for lower absorber thickness and less shunting paths due to a smoother absorber.

Effector Protein Cig2 Decreases Host Tolerance of Infection by Directing Constitutive Fusion of Autophagosomes with the Coxiella-Containing Vacuole

Directory of Open Access Journals (Sweden)

Lara J. Kohler

2016-07-01

Full Text Available Coxiella burnetii replicates in an acidified lysosome-derived vacuole. Biogenesis of the Coxiella-containing vacuole (CCV requires bacterial effector proteins delivered into host cells by the Dot/Icm secretion system. Genetic and cell biological analysis revealed that an effector protein called Cig2 promotes constitutive fusion of autophagosomes with the CCV to maintain this compartment in an autolysosomal stage of maturation. This distinguishes the CCV from other pathogen-containing vacuoles that are targeted by the host autophagy pathway, which typically confers host resistance to infection by delivering the pathogen to a toxic lysosomal environment. By maintaining the CCV in an autolysosomal stage of maturation, Cig2 enabled CCV homotypic fusion and enhanced bacterial virulence in the Galleria mellonella (wax moth model of infection by a mechanism that decreases host tolerance. Thus, C. burnetii residence in an autolysosomal organelle alters host tolerance of infection, which indicates that Cig2-dependent manipulation of a lysosome-derived vacuole influences the host response to infection.

Identifying parasitic current pathways in CIGS solar cells by modelling dark J-V response

NARCIS (Netherlands)

Williams, B.L.; Smit, S.; Kniknie, B.J.; Bakker, K.J.; Keuning, W.; Kessels, W.M.M.; Schropp, R.E.I.; Creatore, M.

2015-01-01

An equivalent circuit model, which allows for the presence of three types of shunting pathways, has been developed to describe the dark J-V characteristics in CIGS solar cells. Excellent agreement between the model and experimental data was apparent throughout a temperature range of 183-323K.

Systems and methods for solar cells with CIS and CIGS films made by reacting evaporated copper chlorides with selenium

Science.gov (United States)

Albin, David S.; Noufi, Rommel

2015-06-09

Systems and methods for solar cells with CIS and CIGS films made by reacting evaporated copper chlorides with selenium are provided. In one embodiment, a method for fabricating a thin film device comprises: providing a semiconductor film comprising indium (In) and selenium (Se) upon a substrate; heating the substrate and the semiconductor film to a desired temperature; and performing a mass transport through vapor transport of a copper chloride vapor and se vapor to the semiconductor film within a reaction chamber.

Defects in Cu(In,Ga)Se{sub 2} chalcopyrite semiconductors: a comparative study of material properties, defect states, and photovoltaic performance

Energy Technology Data Exchange (ETDEWEB)

Cao, Qing; Gunawan, Oki; Copel, Matthew; Reuter, Kathleen B; Chey, S Jay; Mitzi, David B [IBM T.J. Watson Research Center, Yorktown Heights, NY (United States); Deline, Vaughn R [IBM Almaden Resesarch Center, San Jose, CA (United States)

2011-10-15

Understanding defects in Cu(In,Ga)(Se,S){sub 2} (CIGS), especially correlating changes in the film formation process with differences in material properties, photovoltaic (PV) device performance, and defect levels extracted from admittance spectroscopy, is a critical but challenging undertaking due to the complex nature of this polycrystalline compound semiconductor. Here we present a systematic comparative study wherein varying defect density levels in CIGS films were intentionally induced by growing CIGS grains using different selenium activity levels. Material characterization results by techniques including X-ray diffraction, scanning electron microscopy, transmission electron microscopy, secondary ion mass spectrometry, X-ray photoelectron spectroscopy, and medium energy ion scattering indicate that this process variation, although not significantly affecting CIGS grain structure, crystal orientation, or bulk composition, leads to enhanced formation of a defective chalcopyrite layer with high density of indium or gallium at copper antisite defects ((In, Ga){sub Cu}) near the CIGS surface, for CIGS films grown with insufficient selenium supply. This defective layer or the film growth conditions associated with it is further linked with observed current-voltage characteristics, including rollover and crossover behavior, and a defect state at around 110 meV (generally denoted as the N1 defect) commonly observed in admittance spectroscopy. The impact of the (In, Ga){sub Cu} defects on device PV performance is also established. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Cost and Potential of Monolithic CIGS Photovoltaic Modules

Energy Technology Data Exchange (ETDEWEB)

Horowitz, Kelsey; Woodhouse, Michael

2015-06-17

A bottom-up cost analysis of monolithic, glass-glass Cu(In,Ga)(Se,S)2 (CIGS) modules is presented, illuminating current cost drivers for this technology and possible pathways to reduced cost. At 14% module efficiency, for the case of U.S. manufacturing, a manufacturing cost of $0.56/WDC and a minimum sustainable price of $0.72/WDC were calculated. Potential for reduction in manufacturing costs to below $0.40/WDC in the long-term may be possible if module efficiency can be increased without significant increase in $/m2 costs. The levelized cost of energy (LCOE) in Phoenix, AZ under different conditions is assessed and compared to standard c-Si.

Potassium-induced surface modification of Cu(In,Ga)Se2 thin films for high-efficiency solar cells.

Science.gov (United States)

Chirilă, Adrian; Reinhard, Patrick; Pianezzi, Fabian; Bloesch, Patrick; Uhl, Alexander R; Fella, Carolin; Kranz, Lukas; Keller, Debora; Gretener, Christina; Hagendorfer, Harald; Jaeger, Dominik; Erni, Rolf; Nishiwaki, Shiro; Buecheler, Stephan; Tiwari, Ayodhya N

2013-12-01

Thin-film photovoltaic devices based on chalcopyrite Cu(In,Ga)Se2 (CIGS) absorber layers show excellent light-to-power conversion efficiencies exceeding 20%. This high performance level requires a small amount of alkaline metals incorporated into the CIGS layer, naturally provided by soda lime glass substrates used for processing of champion devices. The use of flexible substrates requires distinct incorporation of the alkaline metals, and so far mainly Na was believed to be the most favourable element, whereas other alkaline metals have resulted in significantly inferior device performance. Here we present a new sequential post-deposition treatment of the CIGS layer with sodium and potassium fluoride that enables fabrication of flexible photovoltaic devices with a remarkable conversion efficiency due to modified interface properties and mitigation of optical losses in the CdS buffer layer. The described treatment leads to a significant depletion of Cu and Ga concentrations in the CIGS near-surface region and enables a significant thickness reduction of the CdS buffer layer without the commonly observed losses in photovoltaic parameters. Ion exchange processes, well known in other research areas, are proposed as underlying mechanisms responsible for the changes in chemical composition of the deposited CIGS layer and interface properties of the heterojunction.

Dataset demonstrating the modeling of a high performance Cu(In,GaSe2 absorber based thin film photovoltaic cell

Directory of Open Access Journals (Sweden)

Md. Asaduzzaman

2017-04-01

Full Text Available The physical data of the semiconductor materials used in the design of a CIGS absorber based thin film photovoltaic cell have been presented in this data article. Besides, the values of the contact parameter and operating conditions of the cell have been reported. Furthermore, by conducting the simulation with data corresponding to the device structure: soda-lime glass (SLG substrate/Mo back-contact/CIGS absorber/CdS buffer/intrinsic ZnO/Al-doped ZnO window/Al-grid front-contact, the solar cell performance parameters such as open circuit voltage (Voc, short circuit current density Jsc, fill factor (FF, efficiency (η, and collection efficiency ηc have been analyzed.

The exposure of CIGS solar cells to different electrical biases in a damp-heat illumination environment

NARCIS (Netherlands)

Theelen, M.; Steijvers, H.; Bakker, K.; Vink, J.; Mortazavi, S.; Mulder, A.; Barreau, N.; Roosen, D.; Haverkamp, E.

2016-01-01

Two hybrid degradation setups, allowing exposure of solar cells and modules to elevated temperatures and humidity as well as illumination have been built. CIGS solar cells were placed in the degradation setups, allowing real time monitoring of their electrical properties. Under open circuit

Understanding the Effect of Na in Improving the Performance of CuInSe₂ Based Photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Dobson, Kevin D. [Univ. of Delaware, Newark, DE (United States)

2015-11-17

nature and role of Na diffusion into grain interiors was less clear. In Task 2, single crystal CuInSe₂ was used as a model system to represent the grain interiors of CIGS. Crystals processed by two different methods of different compositions and dislocation densities, were evaluated. Diffusion coefficients were obtained at two temperatures after Na diffusion, giving near identical values, ~2x10¹¹ cm²/s and ~6x10¹¹ cm2/s at 420°C and 480°C, respectively, for each crystal. Characterization confirmed that dislocation densities were too low to significantly impact the effective diffusion coefficient. The Cu-poor crystal had a higher solubility suggesting that Na diffusion is mediated by Cu-vacancies, but was not accompanied by an expected increase in diffusion coefficient. The activation energy for diffusion was similar to values expected for interstitial diffusion, but the large size of Na⁺ ions should result in a solubility that is much lower than what was experimentally measured. A hybrid interstitial-substitutional mechanism is proposed that combines the fast diffusion of interstitial atoms with the high solubility common for substitutional impurities. Lattice diffusion of Na proceeds fast enough that CIGS grain interiors will have Na concentrations near the solubility limit of 1018 cm^-3 when manufactured under standard conditions. Na and K treated epitaxial CIS films showed a significant increase in cathodoluminescence emission intensity, indicating a reduction of non-radiative recombination pathways, which is consistent with improvements in CIGS device performance, though the mechanism is not clear. Pathways forward: Despite the success of this project, there are a number of questions remaining related to further the understanding of the chemistry of Na in CIGS films and devices. These include further elucidation of the mechanisms of Na passivation in CIGS GBs, with identification of which defects are

Investigation of an Electrochemical Method for Separation of Copper, Indium, and Gallium from Pretreated CIGS Solar Cell Waste Materials

Directory of Open Access Journals (Sweden)

Anna M. K. Gustafsson

2015-01-01

Full Text Available Recycling of the semiconductor material copper indium gallium diselenide (CIGS is important to ensure a future supply of indium and gallium, which are relatively rare and therefore expensive elements. As a continuation of our previous work, where we recycled high purity selenium from CIGS waste materials, we now show that copper and indium can be recycled by electrodeposition from hydrochloric acid solutions of dissolved selenium-depleted material. Suitable potentials for the reduction of copper and indium were determined to be −0.5 V and −0.9 V (versus the Ag/AgCl reference electrode, respectively, using cyclic voltammetry. Electrodeposition of first copper and then indium from a solution containing the dissolved residue from the selenium separation and ammonium chloride in 1 M HCl gave a copper yield of 100.1 ± 0.5% and an indium yield of 98.1 ± 2.5%. The separated copper and indium fractions contained no significant contamination of the other elements. Gallium remained in solution together with a small amount of indium after the separation of copper and indium and has to be recovered by an alternative method since electrowinning from the chloride-rich acid solution was not effective.

Commercialization of High Efficiency Low Cost CIGS Technology Based on Electroplating: Final Technical Progress Report, 28 September 2007 - 30 June 2009

Energy Technology Data Exchange (ETDEWEB)

Basol, B.

2010-08-01

This report describes SoloPower's work as a Photovoltaic Technology Incubator awardee within the U.S. Department of Energy's Solar Energy Technologies Program. The term of this subcontract with the National Renewable Energy Laboratory was two years. The project focused on SoloPower's electrodeposition-based copper indium gallium (di)selenide (CIGS) technology. Under this subcontract, SoloPower improved the quality of its flexible metal substrates, increased the size of its solar cells from 0.5 cm2 to 120 cm2, increased the small-area cell efficiencies from near 11% to near 14%, demonstrated large-area cells, and developed a module manufacturing process.

Preparation of CIGS thin films by HiPIMS or DC sputtering and various selenization processes

Czech Academy of Sciences Publication Activity Database

Olejníček, Jiří; Hubička, Zdeněk; Kšírová, Petra; Kment, Štěpán; Brunclíková, Michaela; Kohout, Michal; Čada, Martin; Darveau, S.A.; Exstrom, C.L.

2013-01-01

Roč. 16, č. 2 (2013), s. 314-319 ISSN 1203-8407 R&D Projects: GA MŠk LH12045 Institutional support: RVO:68378271 Keywords : CIGS * HIPIMS * selenization * nanocrystals * solar energy * sputtering * thin films Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 1.106, year: 2013 http://www.ingentaconnect.com/content/stn/jaots/2013/00000016/00000002/art00015

The effect of damp heat-illumination exposure on CIGS solar cells: A combined XRD and electrical characterization study

NARCIS (Netherlands)

Theelen, M.; Hendrikx, R.; Barreau, N.; Steijvers, H.; Böttger, A.

2016-01-01

Unencapsulated CIGS solar cells were simultaneously exposed to damp heat and illumination. In-situ monitoring of their electrical parameters demonstrated a rapid decrease of the efficiency, mainly driven by changes in the series and shunt resistances. The non-degraded and degraded solar cells were

Photoelectrochemical water splitting for hydrogen production using combination of CIGS2 solar cell and RuO2 photocatalyst

International Nuclear Information System (INIS)

Dhere, Neelkanth G.; Jahagirdar, Anant H.

2005-01-01

This paper presents the development of photoelectrochemical (PEC) cell for water splitting setup using multiple band gap combination of CuIn 1-x Ga x S 2 (CIGS2) thin-film photovoltaic (PV) cell and ruthenium oxide (RuO 2 ) photocatalyst. FSEC PV Materials Lab has developed a PEC setup consisting of two illuminated CIGS2 cells, a ruthenium oxide (RuO 2 ) anode deposited on titanium sheet for oxygen evolution and a platinum foil cathode for hydrogen evolution. With this combination, a PEC efficiency of 4.29% has been achieved. This paper also presents the research aimed at further improvements in the PEC efficiency by employing highly efficient photoanode that can be illuminated by photons not absorbed at the PV cell and by increasing the concentration of electrolyte solution (pH 10). The former will be achieved by employing a p-type transparent and conducting layer at the back of PV cell to transmit the unabsorbed photons, and the latter will reduce the resistance offered by the electrolyte. Concentration of the electrolyte was increased by five times, and the I-V characteristics of both RuO 2 and RuS 2 were measured with and without illumination. The results indicate that PEC efficiencies of over 9% can be achieved using RuS 2 with illumination and five times concentrated pH 10 solution instead of pH 10 with normal concentration

A high-efficiency solution-deposited thin-film photovoltaic device

Energy Technology Data Exchange (ETDEWEB)

Mitzi, David B; Yuan, Min; Liu, Wei; Chey, S Jay; Schrott, Alex G [IBM T. J. Watson Research Center, Yorktown Heights, NY (United States); Kellock, Andrew J; Deline, Vaughn [IBM Almaden Research Center, San Jose, CA (United States)

2008-10-02

High-quality Cu(In,Ga)Se{sub 2} (CIGS) films are deposited from hydrazine-based solutions and are employed as absorber layers in thin-film photovoltaic devices. The CIGS films exhibit tunable stoichiometry and well-formed grain structure without requiring post-deposition high-temperature selenium treatment. Devices based on these films offer power conversion efficiencies of 10% (AM1.5 illumination). (Abstract Copyright [2008], Wiley Periodicals, Inc.)

Photoelectrochemical water splitting for hydrogen production using combination of CIGS2 solar cell and RuO{sub 2} photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Dhere, Neelkanth G. [University of Central Florida, Florida Solar Energy Center, 1679 Clearlake Road Cocoa, FL 32922-5703 (United States)]. E-mail: dhere@fsec.ucf.edu; Jahagirdar, Anant H. [University of Central Florida, Florida Solar Energy Center, 1679 Clearlake Road Cocoa, FL 32922-5703 (United States)

2005-06-01

This paper presents the development of photoelectrochemical (PEC) cell for water splitting setup using multiple band gap combination of CuIn{sub 1-x}Ga {sub x}S{sub 2} (CIGS2) thin-film photovoltaic (PV) cell and ruthenium oxide (RuO{sub 2}) photocatalyst. FSEC PV Materials Lab has developed a PEC setup consisting of two illuminated CIGS2 cells, a ruthenium oxide (RuO{sub 2}) anode deposited on titanium sheet for oxygen evolution and a platinum foil cathode for hydrogen evolution. With this combination, a PEC efficiency of 4.29% has been achieved. This paper also presents the research aimed at further improvements in the PEC efficiency by employing highly efficient photoanode that can be illuminated by photons not absorbed at the PV cell and by increasing the concentration of electrolyte solution (pH 10). The former will be achieved by employing a p-type transparent and conducting layer at the back of PV cell to transmit the unabsorbed photons, and the latter will reduce the resistance offered by the electrolyte. Concentration of the electrolyte was increased by five times, and the I-V characteristics of both RuO{sub 2} and RuS{sub 2} were measured with and without illumination. The results indicate that PEC efficiencies of over 9% can be achieved using RuS{sub 2} with illumination and five times concentrated pH 10 solution instead of pH 10 with normal concentration.

Improving the efficiency of copper indium gallium (Di-selenide (CIGS solar cells through integration of a moth-eye textured resist with a refractive index similar to aluminum doped zinc oxide

Directory of Open Access Journals (Sweden)

M. Burghoorn

2014-12-01

Full Text Available Textured transparent conductors are widely used in thin-film silicon solar cells. They lower the reflectivity at interfaces between different layers in the cell and/or cause an increase in the path length of photons in the Si absorber layer, which both result in an increase in the number of absorbed photons and, consequently, an increase in short-circuit current density (Jsc and cell efficiency. Through optical simulations, we recently obtained strong indications that texturing of the transparent conductor in copper indium gallium (di-selenide (CIGS solar cells is also optically advantageous. Here, we experimentally demonstrate that the Jsc and efficiency of CIGS solar cells with an absorber layer thickness (dCIGS of 0.85 μm, 1.00 μm and 2.00 μm increase through application of a moth-eye textured resist with a refractive index that is sufficiently similar to AZO (nresist = 1.792 vs. nAZO = 1.913 at 633 nm to avoid large optical losses at the resist-AZO interface. On average, Jsc increases by 7.2%, which matches the average reduction in reflection of 7.0%. The average relative increase in efficiency is slightly lower (6.0%. No trend towards a larger relative increase in Jsc with decreasing dCIGS was observed. Ergo, the increase in Jsc can be fully explained by the reduction in reflection, and we did not observe any increase in Jsc based on an increased photon path length.

Indium tin oxide with titanium doping for transparent conductive film application on CIGS solar cells

Energy Technology Data Exchange (ETDEWEB)

Liu, Wei-Sheng; Cheng, Huai-Ming; Hu, Hung-Chun; Li, Ying-Tse; Huang, Shi-Da; Yu, Hau-Wei [Department of Photonics Engineering, Yuan Ze University, Chung-Li 32003, Taiwan (China); Pu, Nen-Wen, E-mail: nwpuccit@gmail.com [Department of Photonics Engineering, Yuan Ze University, Chung-Li 32003, Taiwan (China); Liang, Shih-Chang [Materials & Electro-Optics Research Division, National Chung-Shan Institute of Science and Technology, Lung Tan 32599, Taiwan (China)

2015-11-01

Highlights: • Ti-doped indium tin oxide (ITO) films were deposited by DC magnetron sputtering. • Optimal optoelectronic properties were achieved at a sputtering power of 100 W. • Resistivity = 3.2 × 10{sup −4} Ω-cm without substrate heating or post growth annealing. • Mean visible and NIR transmittances of 83 and 80%, respectively, were achieved. • Efficient batteries (11.3%) were fabricated by applying ITO:Ti to CIGS solar cells. - Abstract: In this study, Ti-doped indium tin oxide (ITO:Ti) thin films were fabricated using a DC-magnetron sputtering deposition method. The thin films were grown without introducing oxygen or heating the substrate, and no post-growth annealing was performed after fabrication. The thickness of the ITO:Ti thin films (350 nm) was controlled while increasing the sputtering power from 50 to 150 W. According to the results, the optimal optoelectronic properties were observed in ITO:Ti thin films grown at a sputtering power of 100 W, yielding a reduced resistivity of 3.2 × 10{sup −4} Ω-cm and a mean high transmittance of 83% at wavelengths ranging from 400 to 800 nm. The optimal ITO:Ti thin films were used to fabricate a Cu(In,Ga)Se{sub 2} solar cell that exhibited a photoelectric conversion efficiency of 11.3%, a short-circuit current density of 33.1 mA/cm{sup 2}, an open-circuit voltage of 0.54 V, and a fill factor of 0.64.

Device Modeling of the Performance of Cu(In,GaSe2 Solar Cells with V-Shaped Bandgap Profiles

Directory of Open Access Journals (Sweden)

Shou-Yi Kuo

2014-01-01

Full Text Available The effect of Cu(In,GaSe2 (CIGS with V-shaped bandgap on device performance is investigated in detail. A series of Ga/(In+Ga ratio are set to study the influence of V-shaped bandgap profile on the electricity of CIGS thin film solar cells. The modeling of device current density-voltage (J-V curve and bandgap grading profile corresponded well to measurement results. Detailed characteristic and modeling results show that an increased gradient of bandgap from valley to the buffer layer CdS will result in a barrier and lead to an enhanced recombination in the valley. This phenomenon can be modified by the back electric field resulting from a gradient bandgap from valley (bandgap minimum to the Mo back contact. These results indicate CIGS-based solar cells can achieve higher performance by optimizing the V-shaped bandgap profile.

Improving the efficiency of copper indium gallium (Di-)selenide (CIGS) solar cells through integration of a moth-eye textured resist with a refractive index similar to aluminum doped zinc oxide

Energy Technology Data Exchange (ETDEWEB)

Burghoorn, M.; Kniknie, B.; Deelen, J. van; Ee, R. van [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); Xu, M. [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); Delft University of Technology, Optics Group, Van der Waalsweg 8, 2628 CH, Delft (Netherlands); Vroon, Z. [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); Zuyd Hogeschool, Nieuw Eyckholt 300, 6419 DJ, Heerlen (Netherlands); Belt, R. van de [Kriya Materials BV, Urmonderbaan 22, 6167 RD, Geleen (Netherlands); Buskens, P., E-mail: pascal.buskens@tno.nl, E-mail: buskens@dwi.rwth-aachen.de [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); DWI – Leibniz Institute for Interactive Materials, Forckenbeckstrasse 50, 52056, Aachen (Germany)

2014-12-15

Textured transparent conductors are widely used in thin-film silicon solar cells. They lower the reflectivity at interfaces between different layers in the cell and/or cause an increase in the path length of photons in the Si absorber layer, which both result in an increase in the number of absorbed photons and, consequently, an increase in short-circuit current density (J{sub sc}) and cell efficiency. Through optical simulations, we recently obtained strong indications that texturing of the transparent conductor in copper indium gallium (di-)selenide (CIGS) solar cells is also optically advantageous. Here, we experimentally demonstrate that the J{sub sc} and efficiency of CIGS solar cells with an absorber layer thickness (d{sub CIGS}) of 0.85 μm, 1.00 μm and 2.00 μm increase through application of a moth-eye textured resist with a refractive index that is sufficiently similar to AZO (n{sub resist} = 1.792 vs. n{sub AZO} = 1.913 at 633 nm) to avoid large optical losses at the resist-AZO interface. On average, J{sub sc} increases by 7.2%, which matches the average reduction in reflection of 7.0%. The average relative increase in efficiency is slightly lower (6.0%). No trend towards a larger relative increase in J{sub sc} with decreasing d{sub CIGS} was observed. Ergo, the increase in J{sub sc} can be fully explained by the reduction in reflection, and we did not observe any increase in J{sub sc} based on an increased photon path length.

The Effect of Sputtering Parameters on the Film Properties of Molybdenum Back Contact for CIGS Solar Cells

Directory of Open Access Journals (Sweden)

Peng-cheng Huang

2013-01-01

Full Text Available Molybdenum (Mo thin films are widely used as a back contact for CIGS-based solar cells. This paper determines the optimal settings for the sputtering parameters for an Mo thin film prepared on soda lime glass substrates, using direct current (dc magnetron sputtering, with a metal Mo target, in an argon gas environment. A Taguchi method with an L9 orthogonal array, the signal-to-noise ratio, and an analysis of variances is used to determine the performance characteristics of the coating operation. The main sputtering parameters, such as working pressure (mTorr, dc power (W, and substrate temperature (°C, are optimized with respect to the structural features, surface morphology, and electrical properties of the Mo films. An adhesive tape test is performed on each film to determine the adhesion strength of the films. The experimental results show that the working pressure has the dominant effect on electrical resistivity and reflectance. The intensity of the main peak (110 for the Mo film increases and the full width at half maximum decreases gradually as the sputtering power is increased. Additionally, the application of an Mo bilayer demonstrates good adherence and low resistivity.

Cu−In−Ga−S quantum dot composition-dependent device performance of electrically driven light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Kim, Jong-Hoon; Lee, Ki-Heon; Jo, Dae-Yeon; Yang, Heesun, E-mail: hyang@hongik.ac.kr [Department of Materials Science and Engineering, Hongik University, Seoul 121-791 (Korea, Republic of); Lee, Yangjin; Hwang, Jun Yeon [Institute of Advanced Composite Materials, Korea Institute of Science and Technology, Jeonbuk 565-905 (Korea, Republic of)

2014-09-29

Colloidal synthesis of ternary and quaternary quantum dots (QDs) of In/Ga ratio-varied Cu−In{sub 1−x}−Ga{sub x}−S (CIGS) with nominal x = 0, 0.5, 0.7, and 1 and their application for the fabrication of quantum dot-light-emitting diodes (QLEDs) are reported. Four QLEDs having CIGS QDs with different compositions are all solution-processed in the framework of multilayered structure, where QD emitting layer is sandwiched by hybrid charge transport layers of poly(9-vinlycarbazole) and ZnO nanoparticles. The device performance such as luminance and efficiency is found to be strongly dependent on the composition of CIGS QDs, and well interpreted by the device energy level diagram proposed through the determination of QD valence band minima by photoelectron emission spectroscopic measurement.

Improved quantitative analysis of Cu(In,Ga)Se{sub 2} thin films using MCs{sup +}-SIMS depth profiling

Energy Technology Data Exchange (ETDEWEB)

Lee, Jihye; Kim, Seon Hee; Lee, Kang-Bong; Lee, Yeonhee [Korea Institute of Science and Technology, Advanced Analysis Center, Seoul (Korea, Republic of); Min, Byoung Koun [Korea Institute of Science and Technology, Clean Energy Research Center, Seoul (Korea, Republic of)

2014-06-15

The chalcopyrite semiconductor, Cu(InGa)Se{sub 2} (CIGS), is popular as an absorber material for incorporation in high-efficiency photovoltaic devices because it has an appropriate band gap and a high absorption coefficient. To improve the efficiency of solar cells, many research groups have studied the quantitative characterization of the CIGS absorber layers. In this study, a compositional analysis of a CIGS thin film was performed by depth profiling in secondary ion mass spectrometry (SIMS) with MCs{sup +} (where M denotes an element from the CIGS sample) cluster ion detection, and the relative sensitivity factor of the cluster ion was calculated. The emission of MCs{sup +} ions from CIGS absorber elements, such as Cu, In, Ga, and Se, under Cs{sup +} ion bombardment was investigated using time-of-flight SIMS (TOF-SIMS) and magnetic sector SIMS. The detection of MCs{sup +} ions suppressed the matrix effects of varying concentrations of constituent elements of the CIGS thin films. The atomic concentrations of the CIGS absorber layers from the MCs{sup +}-SIMS exhibited more accurate quantification compared to those of elemental SIMS and agreed with those of inductively coupled plasma atomic emission spectrometry. Both TOF-SIMS and magnetic sector SIMS depth profiles showed a similar MCs{sup +} distribution for the CIGS thin films. (orig.)

Rubidium distribution at atomic scale in high efficient Cu(In,Ga)Se2 thin-film solar cells

Science.gov (United States)

Vilalta-Clemente, Arantxa; Raghuwanshi, Mohit; Duguay, Sébastien; Castro, Celia; Cadel, Emmanuel; Pareige, Philippe; Jackson, Philip; Wuerz, Roland; Hariskos, Dimitrios; Witte, Wolfram

2018-03-01

The introduction of a rubidium fluoride post deposition treatment (RbF-PDT) for Cu(In,Ga)Se2 (CIGS) absorber layers has led to a record efficiency up to 22.6% for thin-film solar cell technology. In the present work, high efficiency CIGS samples with RbF-PDT have been investigated by atom probe tomography (APT) to reveal the atomic distribution of all alkali elements present in CIGS layers and compared with non-treated samples. A Scanning Electron Microscopy Dual beam station (Focused Ion Beam-Gas Injection System) as well as Transmission Kikuchi diffraction is used for atom probe sample preparation and localization of the grain boundaries (GBs) in the area of interest. The analysis of the 3D atomic scale APT reconstructions of CIGS samples with RbF-PDT shows that inside grains, Rb is under the detection limit, but the Na concentration is enhanced as compared to the reference sample without Rb. At the GBs, a high concentration of Rb reaching 1.5 at. % was found, and Na and K (diffusing from the glass substrate) are also segregated at GBs but at lower concentrations as compared to Rb. The intentional introduction of Rb leads to significant changes in the chemical composition of CIGS matrix and at GBs, which might contribute to improve device efficiency.

Thin Film CIGS Solar Cells, Photovoltaic Modules, and the Problems of Modeling

Directory of Open Access Journals (Sweden)

Antonino Parisi

2013-01-01

Full Text Available Starting from the results regarding a nonvacuum technique to fabricate CIGS thin films for solar cells by means of single-step electrodeposition, we focus on the methodological problems of modeling at cell structure and photovoltaic module levels. As a matter of fact, electrodeposition is known as a practical alternative to costly vacuum-based technologies for semiconductor processing in the photovoltaic device sector, but it can lead to quite different structural and electrical properties. For this reason, a greater effort is required to ensure that the perspectives of the electrical engineer and the material scientist are given an opportunity for a closer comparison and a common language. Derived parameters from ongoing experiments have been used for simulation with the different approaches, in order to develop a set of tools which can be used to put together modeling both at single cell structure and complete module levels.

A high intensity positron beam at the Brookhaven reactor

International Nuclear Information System (INIS)

Weber, M.; Lynn, K.G.; Roellig, L.O.; Mills, A.P. Jr.; Moodenbaugh, A.R.

1987-01-01

We describe a high intensity, low energy positron beam utilizing high specific activity /sup 64/Cu sources (870 Ci/g) produced in a reactor with high thermal neutron flux. Fast-to-slow moderation can be performed in a self moderation mode or with a transmission moderator. Slow positron rates up to 1.6 x 10/sup 8/ e/sup +//s with a half life of 12.8 h are calculated. Up to 1.0 x 10/sup 8/ e/sup +//s have been observed. New developments including a Ne moderator and an on-line isotope separation process are discussed. 21 refs., 9 figs

Characterization of grain boundaries in Cu(In,Ga)Se{sub 2} by atom probe tomography

Energy Technology Data Exchange (ETDEWEB)

Schwarz, Torsten; Cojocaru-Miredin, Oana; Choi, Pyuck-Pa; Raabe, Dierk [Max-Planck Institute for Iron Research GmbH, Duesseldorf (Germany); Wuerz, Roland [Zentrum fuer Sonnenenergie- und Wasserstoff-Forschung Baden-Wuerttemberg (ZSW), Stuttgart (Germany)

2012-07-01

Solar cells based on the compound semiconductor Cu(In,Ga)Se{sub 2} (CIGS) as absorber material exhibit the highest efficiency among all thin-film solar cells. This is surprising high in view of the polycrystalline defect-rich structure of the CIGS absorber films. The high efficiency has been commonly ascribed to the diffusion of alkali metal atoms from the soda-lime glass substrate into the CIGS layer, which can render the grain boundaries (GB) electrically inactive. However, the exact mechanisms of how these impurities enhance the cell efficiency are yet to be clarified. As a step towards a better understanding of CIGS solar cells, we have analyzed the composition of solar-grade CIGS layers at the atomic-scale by using pulsed laser Atom Probe Tomography (APT). To perform APT analyses on selected GBs site-specific sample preparation was carried out using the Focused Ion Beam lift-out technique. In addition, Electron Back Scattered Diffraction was performed to characterize the structure and misorientation of selected GBs. Using APT, segregation of impurities at the GBs was directly observed. APT data of various types of GBs are presented and discussed with respect to the possible effects on the cell efficiency.

High-throughput combinatorial chemical bath deposition: The case of doping Cu (In, Ga) Se film with antimony

Science.gov (United States)

Yan, Zongkai; Zhang, Xiaokun; Li, Guang; Cui, Yuxing; Jiang, Zhaolian; Liu, Wen; Peng, Zhi; Xiang, Yong

2018-01-01

The conventional methods for designing and preparing thin film based on wet process remain a challenge due to disadvantages such as time-consuming and ineffective, which hinders the development of novel materials. Herein, we present a high-throughput combinatorial technique for continuous thin film preparation relied on chemical bath deposition (CBD). The method is ideally used to prepare high-throughput combinatorial material library with low decomposition temperatures and high water- or oxygen-sensitivity at relatively high-temperature. To check this system, a Cu(In, Ga)Se (CIGS) thin films library doped with 0-19.04 at.% of antimony (Sb) was taken as an example to evaluate the regulation of varying Sb doping concentration on the grain growth, structure, morphology and electrical properties of CIGS thin film systemically. Combined with the Energy Dispersive Spectrometer (EDS), X-ray Photoelectron Spectroscopy (XPS), automated X-ray Diffraction (XRD) for rapid screening and Localized Electrochemical Impedance Spectroscopy (LEIS), it was confirmed that this combinatorial high-throughput system could be used to identify the composition with the optimal grain orientation growth, microstructure and electrical properties systematically, through accurately monitoring the doping content and material composition. According to the characterization results, a Sb2Se3 quasi-liquid phase promoted CIGS film-growth model has been put forward. In addition to CIGS thin film reported here, the combinatorial CBD also could be applied to the high-throughput screening of other sulfide thin film material systems.

A comparative study of solution-processed low- and high-band-gap chalcopyrite thin-film solar cells

International Nuclear Information System (INIS)

Park, Se Jin; Moon, Sung Hwan; Min, Byoung Koun; Cho, Yunae; Kim, Ji Eun; Kim, Dong-Wook; Lee, Doh-Kwon; Gwak, Jihye; Kim, Jihyun

2014-01-01

Low-cost and printable chalcopyrite thin-film solar cells were fabricated by a precursor solution-based coating method with a multi-step heat-treatment process (oxidation, sulfurization, and selenization). The high-band-gap (1.57 eV) Cu(In x Ga 1−x )S 2 (CIGS) solar cell showed a high open-circuit voltage of 787 mV, whereas the low-band-gap (1.12 eV) Cu(In x Ga 1−x )(S 1−y Se y ) 2 (CIGSSe) cell exhibited a high short-circuit current density of 32.6 mA cm −2 . The energy conversion efficiencies were 8.28% for CIGS and 8.81% for CIGSSe under standard irradiation conditions. Despite similar efficiencies, the two samples showed notable differences in grain size, surface morphology, and interfacial properties. Low-temperature transport and admittance characteristics of the samples clearly revealed how their structural differences influenced their photovoltaic and electrical properties. Such analyses provide insight into the enhanced solar cell performance of the solution-processed chalcopyrite thin films. (paper)

Growth of polycrystalline Cu(In,Ga)Se2 thin films using a radio frequency-cracked Se-radical beam source and application for photovoltaic devices

International Nuclear Information System (INIS)

Ishizuka, Shogo; Shibata, Hajime; Yamada, Akimasa; Fons, Paul; Sakurai, Keiichiro; Matsubara, Koji; Niki, Shigeru

2007-01-01

Cu(In,Ga)Se 2 (CIGS) thin films were grown using a rf-cracked Se-radical beam source. A unique combination of film properties, a highly dense and smooth surface with large grain size, is shown. These features seem to have no significant influence on the photovoltaic performance. Defect control in bulk CIGS leading to corresponding variations in the electrical and photoluminescence properties was found to be possible by regulating the Se-radical source parameters. A competitive energy conversion efficiency of 17.5%, comparable to that of a Se-evaporative source grown CIGS device, has been demonstrated from a solar cell fabricated using a Se-radical source grown CIGS absorber

The performance of a combined solar photovoltaic (PV) and thermoelectric generator (TEG) system

DEFF Research Database (Denmark)

Bjørk, Rasmus; Nielsen, Kaspar Kirstein

2015-01-01

The performance of a combined solar photovoltaic (PV) and thermoelectric generator (TEG) system is examined using an analytical model for four different types of commercial PVs and a commercial bismuth telluride TEG. The TEG is applied directly on the back of the PV, so that the two devices have...... the same temperature. The PVs considered are crystalline Si (c-Si), amorphous Si (a-Si), copper indium gallium (di) selenide (CIGS) and cadmium telluride (CdTe) cells. The degradation of PV performance with temperature is shown to dominate the increase in power produced by the TEG, due to the low...... efficiency of the TEG. For c-Si, CIGS and CdTe PV cells the combined system produces a lower power and has a lower efficiency than the PV alone, whereas for an a-Si cell the total system performance may be slightly increased by the TEG....

Solar Spectral and Module Temperature Influence on the Outdoor Performance of Thin Film PV Modules Deployed on a Sunny Inland Site

Directory of Open Access Journals (Sweden)

G. Nofuentes

2013-01-01

Full Text Available This work aims at analysing the influence of both module temperature and solar spectrum distribution on the outdoor performance of the following thin film technologies: hydrogenated amorphous silicon (a-Si:H, cadmium telluride (CdTe, copper indium gallium selenide sulfide (CIGS, and hydrogenated amorphous silicon/hydrogenated microcrystalline silicon hetero-junction (a-Si:H/μc-Si:H. A 12-month experimental campaign carried out in a sunny inland site in which a module of each one of these technologies was tested and measured outdoors has provided the necessary empirical data. Results show that module temperature exerts a limited influence on the performance of the tested a-Si:H, CdTe, and a-Si:H/μc-Si:H modules. In contrast, the outdoor behaviour of the CIGS module is the most affected by its temperature. Blue-rich spectra enhance the outdoor behaviour of the a-Si:H and a-Si:H/μc-Si:H modules while it is the other way round for the CIGS module. However, the CdTe specimen shows little sensitivity to the solar spectrum distribution. Anyway, spectral effects are scarcely relevant on an annual basis, ranging from gains for the CIGS module (1.5% to losses for the a-Si:H module (1.0%. However, the seasonal impact of the spectrum shape is more noticeable in these two materials; indeed, spectral issues may cause performance gains or losses of up to some 4% when winter and summer periods are considered.

Highly reflective rear surface passivation design for ultra-thin Cu(In,Ga)Se{sub 2} solar cells

Energy Technology Data Exchange (ETDEWEB)

Vermang, Bart, E-mail: Bart.Vermang@angstrom.uu.se [Ångström Solar Center, University of Uppsala, Uppsala 75121 (Sweden); ESAT-KU Leuven, University of Leuven, Leuven 3001 (Belgium); Wätjen, Jörn Timo; Fjällström, Viktor; Rostvall, Fredrik; Edoff, Marika [Ångström Solar Center, University of Uppsala, Uppsala 75121 (Sweden); Gunnarsson, Rickard; Pilch, Iris; Helmersson, Ulf [Plasma & Coatings Physics, University of Linköping, Linköping 58183 (Sweden); Kotipalli, Ratan; Henry, Frederic; Flandre, Denis [ICTEAM/IMNC, Université Catholique de Louvain, Louvain-la-Neuve 1348 (Belgium)

2015-05-01

Al{sub 2}O{sub 3} rear surface passivated ultra-thin Cu(In,Ga)Se{sub 2} (CIGS) solar cells with Mo nano-particles (NPs) as local rear contacts are developed to demonstrate their potential to improve optical confinement in ultra-thin CIGS solar cells. The CIGS absorber layer is 380 nm thick and the Mo NPs are deposited uniformly by an up-scalable technique and have typical diameters of 150 to 200 nm. The Al{sub 2}O{sub 3} layer passivates the CIGS rear surface between the Mo NPs, while the rear CIGS interface in contact with the Mo NP is passivated by [Ga]/([Ga] + [In]) (GGI) grading. It is shown that photon scattering due to the Mo NP contributes to an absolute increase in short circuit current density of 3.4 mA/cm{sup 2}; as compared to equivalent CIGS solar cells with a standard back contact. - Highlights: • Proof-of-principle ultra-thin CIGS solar cells have been fabricated. • The cells have Mo nano-particles (NPs) as local rear contacts. • An Al{sub 2}O{sub 3} film passivates the CIGS rear surface between these nano-particles. • [Ga]/([Ga] + [In]) grading is used to reduce Mo-NP/CIGS interface recombination.

Degradation of Cu(In, Ga)Se{sub 2} thin-film solar cells due to the ionization effect of low-energy electrons

Energy Technology Data Exchange (ETDEWEB)

Kawakita, Shirou, E-mail: kawakita.shirou@jaxa.jp [Japan Aerospace Exploration Agency (JAXA), Tsukuba, Ibaraki 305-8505 (Japan); Imaizumi, Mitsuru [Japan Aerospace Exploration Agency (JAXA), Tsukuba, Ibaraki 305-8505 (Japan); Ishizuka, Shogo; Shibata, Hajime; Niki, Shigeru [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Ibaraki 305-8568 (Japan); Okuda, Shuichi [Osaka Prefecture University (OPU), Sakai, Osaka 599-8570 (Japan); Kusawake, Hiroaki [Japan Aerospace Exploration Agency (JAXA), Tsukuba, Ibaraki 305-8505 (Japan)

2015-05-01

Cu (In, Ga)Se{sub 2} (CIGS) solar cells were irradiated with 100 keV electrons to reveal the characteristics of created radiation defects. 100 keV electrons cannot produce any displacement defects in CIGS. Low-fluence electrons improve the electrical performance of the CIGS solar cells due to the change in the conductive type of donor to acceptor in a metastable defect, which is equivalent to the light-soaking effect. However, high fluence electrons cause the cell performance to decline. From analysis based on changes in carrier density and electroluminescence, defects causing the decline in performance include donor- and non-radiative types. In addition, red-on-bias experiments showed an increase in III{sub Cu} defects due to electron irradiation. Based on these results, the degradation in the electrical performance of the CIGS solar cells irradiated with high electron fluence would be attributable to a change in the conductive type of III{sub Cu} defects. - Highlights: • Cu(In,Ga)Se2 Solar cells were irradiated with 100 and 250 keV electrons at low temperature. • These electrons degraded the electrical performance of Cu(In,Ga)Se2 sola cells. • The electrons induced ⅢCu defects in Cu(In,Ga)Se2.

Outdoor Performance Comparison of Concentrator Photovoltaic and Flat Plate Photovoltaic Systems

Directory of Open Access Journals (Sweden)

Hidaka Yoshihide

2016-01-01

Full Text Available Output characteristics of tracking type concentrator photovoltaic (CPV system, multi-crystalline silicon (mc-Si PV system, CIGS PV system, and amorphous silicon (a-Si PV system were analyzed in the data period of a year from August 2013 to July 2014. In this study, we analyzed the influence of environmental factors using average photon energy (APE and temperature of solar cell (Tcell. The characteristics of 14 kW CPV system, 50 kW mc-Si PV system, 60 kW CIGS PV system, 1.35 kW a-Si PV system were evaluated and compared. As a result, the output performance of CPV was highest between the four systems at the most frequent conditions in the outdoor environment.

Performance evaluation of photovoltaic systems on Kuwaiti schools’ rooftop

International Nuclear Information System (INIS)

Al-Otaibi, A.; Al-Qattan, A.; Fairouz, F.; Al-Mulla, A.

2015-01-01

Highlights: • Evaluation of rooftop PV installations at 2 Kuwaiti schools was carried out. • Lack of real plants data in the region and specifically Kuwait motivated the work. • Automated cleaning system allowed for minimization of soiling loss. • The average PV system performance was greater than 76%. • Schools show high potential for rooftop installations. - Abstract: Photovoltaic (PV) is a high-potential renewable energy technology for Kuwait to pursue due to high daily irradiation, and has garnered local attention in recent years due to the growing energy demand and concerns over climate change. As yet, no data are available regarding the actual performance of PV systems in Kuwait’s harsh environment. This paper presents a 12-month-long performance evaluation of the first 85.05 kW p and 21.6 kW p copper indium gallium selenide (CIGS) thin film, grid-connected PV systems on the rooftops of two schools. The schools’ monthly energy consumption and PV generation profiles, the actual performance of the PV plants, the effectiveness of automated cleaning systems on the power output, and the benefits of PV implementation in schools were analyzed and evaluated. Data analysis was applied to filter and normalize the data in order to identify the actual performance parameters. The findings of the study, based on solar irradiation collected, the performance of the module technology and the effectiveness of the automated cleaning systems, show that the performance ratio was maintained between 0.74 and 0.85. Furthermore, the minimum monthly energy yield of the PV systems was about 104 kW h/kW p . The annual average daily final yields of the PV systems in this study were 4.5 kW h/kW p /day. The results provided insight into the performance of CIGS grid-connected PV systems in Kuwait, and those data will be beneficial to the PV research community worldwide. School buildings, particularly for the rooftops, are a unique and important asset for urban PV system

Band gap grading and photovoltaic performance of solution-processed Cu(In,Ga)S2 thin-film solar cells.

Science.gov (United States)

Sohn, So Hyeong; Han, Noh Soo; Park, Yong Jin; Park, Seung Min; An, Hee Sang; Kim, Dong-Wook; Min, Byoung Koun; Song, Jae Kyu

2014-12-28

The photophysical properties of CuInxGa1-xS2 (CIGS) thin films, prepared by solution-based coating methods, are investigated to understand the correlation between the optical properties of these films and the electrical characteristics of solar cells fabricated using these films. Photophysical properties, such as the depth-dependent band gap and carrier lifetime, turn out to be at play in determining the energy conversion efficiency of solar cells. A double grading of the band gap in CIGS films enhances solar cell efficiency, even when defect states disturb carrier collection by non-radiative decay. The combinational stacking of different density films leads to improved solar cell performance as well as efficient fabrication because a graded band gap and reduced shunt current increase carrier collection efficiency. The photodynamics of minority-carriers suggests that the suppression of defect states is a primary area of improvement in CIGS thin films prepared by solution-based methods.

The effects of Na on high pressure phases of CuIn0.5Ga0.5Se2 from ab initio calculation

International Nuclear Information System (INIS)

Pluengphon, P; Bovornratanaraks, T; Pinsook, U; Vannarat, S

2012-01-01

The effects of Na atoms on high pressure structural phase transitions of CuIn 0.5 Ga 0.5 Se 2 (CIGS) were studied by an ab initio method using density functional theory. At ambient pressure, CIGS is known to have chalcopyrite (I 4-bar 2 d) structure. The high pressure phase transitions of CIGS were proposed to be the same as the order in the CuInSe 2 phase transitions which are I 4-bar 2 d→F m 3-bar m→C m c m structures. By using the mixture atoms method, the Na concentration in CIGS was studied at 0.1, 1.0 and 6.25%. The positive mixing enthalpy of Na at In/Ga sites (Na InGa ) is higher than that of Na at Cu sites (Na Cu ). It confirmed previous studies that Na preferably substitutes on the Cu sites more than the (In, Ga) sites. From the energy-volume curves, we found that the effect of the Na substitutes is to reduce the hardness of CIGS under high pressure. The most significant effects occur at 6.25% Na. We also found that the electronic density of states of CIGS near the valence band maximum is increased noticeably in the chalcopyrite phase. The band gap is close in the cubic and orthorhombic phases. Also, the Na Cu -Se bond length in the chalcopyrite phase is significantly reduced at 6.25% Na, compared with the pure Cu-Se bond length. Consequently, the energy band gap in this phase is wider than in pure CIGS, and the gap increased at the rate of 31 meV GPa -1 under pressure. The Na has a small effect on the transition pressure. The path of transformation from the cubic to orthorhombic phase was derived. The Cu-Se plane in the cubic phase displaced relatively parallel to the (In, Ga)-Se plane by 18% in order to transform to the Cmcm phase. The enthalpy barrier is 0.020 eV/atom, which is equivalent to a thermal energy of 248 K. We predicted that F m 3-bar m and Cmcm can coexist in some pressure range. (paper)

NIR emitting K2SrCl4:Eu2+, Nd3+ phosphor as a spectral converter for CIGS solar cell

Science.gov (United States)

Tawalare, P. K.; Bhatkar, V. B.; Omanwar, S. K.; Moharil, S. V.

2018-05-01

Intense near-infrared emitting phosphor K2SrCl4:Eu2+,Nd3+ with various concentrations of Nd3+ were synthesized. These are characterized with X-ray diffraction, reflectance, photoluminescence emission and photoluminescence excitation spectroscopy, PL lifetime measurements. The emission can be excited by a broad band in near ultra violet region as a consequence of Eu2+→Nd3+ energy transfer. The efficiency of Eu2+→Nd3+ energy transfer is as high as 95%. Fluorescence decay curves for Eu2+ doped samples are almost exponential and described by τ = 500 ns. Eu2+ lifetimes are shortened after Nd3+ doping. Near infrared Emission intensity is limited by Nd3+→Nd3+ energy transfer and the consequent concentration quenching. Nd3+ emission matches well with the spectral response of CIGS and CIS solar cells. Absorption of near ultra violet radiations followed by conversion to near infrared indicates the potential application in solar photovoltaics.

Inkjet printed Cu(In,Ga)S{sub 2} nanoparticles for low-cost solar cells

Energy Technology Data Exchange (ETDEWEB)

Barbé, Jérémy, E-mail: jeremy.barbe@kaust.edu.sa; Eid, Jessica [King Abdullah University of Science and Technology, Solar and Photovoltaics Engineering Research Center (SPERC), Division of Physical Sciences and Engineering (Saudi Arabia); Ahlswede, Erik; Spiering, Stefanie; Powalla, Michael [Zentrum fur Sonnenenergie- und Wasserstoff-Forschung Baden-Württemberg (ZSW) (Germany); Agrawal, Rakesh [Purdue University, School of Chemical Engineering (United States); Del Gobbo, Silvano, E-mail: silvano.delgobbo@gmail.com [King Abdullah University of Science and Technology, Solar and Photovoltaics Engineering Research Center (SPERC), Division of Physical Sciences and Engineering (Saudi Arabia)

2016-12-15

Cu(In,Ga)Se{sub 2} (CIGSe) thin film solar cells were fabricated by direct inkjet printing of Cu(In,Ga)S{sub 2} (CIGS) nanoparticles followed by rapid thermal annealing under selenium vapor. Inkjet printing is a low-cost, low-waste, and flexible patterning method which can be used for deposition of solution-based or nanoparticle-based CIGS films with high throughput. XRD and Raman spectra indicate that no secondary phase is formed in the as-deposited CIGS film since quaternary chalcopyrite nanoparticles are used as the base solution for printing. Besides, CIGSe films with various Cu/(In + Ga) ratios could be obtained by finely tuning the composition of CIGS nanoparticles contained in the ink, which was found to strongly influence the devices performance and film morphology. To date, this is the first successful fabrication of a solar device by inkjet printing of CIGS nanoparticles.

Inkjet printed Cu(In,Ga)S2 nanoparticles for low-cost solar cells

KAUST Repository

Barbe, Jeremy

2016-12-13

Cu(In,Ga)Se2 (CIGSe) thin film solar cells were fabricated by direct inkjet printing of Cu(In,Ga)S2 (CIGS) nanoparticles followed by rapid thermal annealing under selenium vapor. Inkjet printing is a low-cost, low-waste, and flexible patterning method which can be used for deposition of solution-based or nanoparticle-based CIGS films with high throughput. XRD and Raman spectra indicate that no secondary phase is formed in the as-deposited CIGS film since quaternary chalcopyrite nanoparticles are used as the base solution for printing. Besides, CIGSe films with various Cu/(In + Ga) ratios could be obtained by finely tuning the composition of CIGS nanoparticles contained in the ink, which was found to strongly influence the devices performance and film morphology. To date, this is the first successful fabrication of a solar device by inkjet printing of CIGS nanoparticles.

High efficiency thin-film solar cells

Energy Technology Data Exchange (ETDEWEB)

Schock, Hans-Werner [Helmholtz Zentrum Berlin (Germany). Solar Energy

2012-11-01

Production of photovoltaics is growing worldwide on a gigawatt scale. Among the thin film technologies, Cu(In,Ga)S,Se{sub 2} (CIS or CIGS) based solar cells have been the focus of more and more attention. This paper aims to analyze the success of CIGS based solar cells and the potential of this technology for future photovoltaics large-scale production. Specific material properties make CIS unique and allow the preparation of the material with a wide range of processing options. The huge potential lies in the possibility to take advantage of modern thin film processing equipment and combine it with very high efficiencies beyond 20% already achieved on the laboratory scale. A sustainable development of this technology could be realized by modifying the materials and replacing indium by abundant elements. (orig.)

Photoluminescence of Cu(In,Ga)Se2 in the solar cell preparation process

International Nuclear Information System (INIS)

Sho, Shirakata; Shinji, Yudate; Jyunji, Honda; Naoki, Iwado

2010-01-01

Full text : Sequential step by step photoluminescence (PL) measurements have been carried out on Cu(In,Ga)Se 2 (CIGS) films just after each thin-film processes for the fabrication of the CIGS solar cell. These include, (i) the CIGS film deposition on the Mo-coated soda-lime glass substrate by three-stage method (CIGS/Mo/SLG), (ii) the chemical-bath deposition (CBD) of CdS buffer layer, (iii) deposition of undoped ZnO window layer by RF sputtering, (iv) deposition of Al doped ZnO high-conductive window layer by RF sputtering, (v) Al grid electrode deposition for the CIGS solar cell, and (vi) the mechanical scribing for the electrical isolation of small test cells. Roomtemperature PL measurements have been done with the excitation of a He-Ne laser (632.8 nm, 1 mW) focused on the sample surface to 0.2 mm diameter. PL was dispersed by a polycromator (Horiba: MicroHR) and detected by a cooled InGaAs multichannel detector (1024 pixels). In order to study the uniformity of PL within CIGS films, the two dimensional PL spectrum mapping measurement has been done (0.4-0.6 mm step) using an x-y stage operating in the raster scanning mode. Acquisition time of one PL spectrum was 1 s. Once the fresh CIGS film is exposed to the air, intensity of the near-band-edge PL decreases slowly with time. After few days, PL intensity was one order of magnitude weaker than its initial value. Thus, PL measurement was performed just after the deposition. It was shown that PL spectra of CIGS films taken for each process in the CIGS solar cell preparation. PL of the CIGS film exhibited nearband-edge peak at 1.18 eV. The slight increase of PL intensity was observed after depositions of CdS and ZnO films. After the high conductive ZnO:Al deposition, PL intensity decreases to one third of the initial PL intensity of the fresh CIGS film. No change has been observed with respect to the line shape of PL peaks during the process. In the CIGS solar cell (open circuit condition), PL intensity recovers

Ionization effects on Cu(In, Ga)Se{sub 2} thin-film solar cells

Energy Technology Data Exchange (ETDEWEB)

Kawakita, Shirou; Imaizumi, Mitsuru [Japan Aerospace Exploration Agency, 2-1-1 Sengen, Tsukuba, Ibaraki 305-0031 (Japan); Ishizuka, Shogo; Shibata, Hajime [Institute of National Advanced Industrial Science and Technology, 1-1 Umezono, Tsukuba 305-8568 (Japan); Okuda, Shuichi [Osaka Prefecture University, 1-2 Gakuenmachi, Sakai 599-8570 (Japan)

2017-06-15

Cu (In, Ga) Se{sub 2} (CIGS) solar cells were irradiated with 60, 100, and 250 keV electrons to reveal the characteristics of radiation induced defects. Electrons with less than 200 keV energy cannot generate any displacement defects in CIGS materials. In addition, a low amount of the electrons can improve the roll-over behavior in current-voltage characteristics of CIGS solar cells. However, the deterioration of the electrical performance in CIGS solar cells irradiated with a high amount of electrons was observed. The deterioration rate on the cells irradiated with lower-energy electrons was higher than that induced by electrons with higher-energy. The degradation curve of J{sub SC} based on the ionizing dose estimated from the ionizing energy loss model does not depend on the energy of electrons. Therefore, it implies that the electrons can degrade CIGS solar cells due to the ionization effect. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Photonic sintering of thin film prepared by dodecylamine capped CuIn{sub x}Ga{sub 1−x}Se{sub 2} nanoparticles for printed photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Singh, Manjeet, E-mail: msitbhu@gmail.com; Jiu, Jinting; Sugahara, Tohru; Suganuma, Katsuaki

2014-08-28

In this paper, we report solution phase large scale synthesis of monodisperse phase pure CuIn{sub x}Ga{sub 1−x}Se{sub 2} (CIGS) nanoparticles by using dodecylamine as solvent and dispersant. Various compositions of CIGS nanoparticles with different Ga content are synthesized by simply adding different amounts of Ga precursors. The band gap of CIGS nanoparticles can be tuned by changing Ga content. Effort is given to understand the formation pathway of CIGS phase so as to make the synthesis easier for the desired product. High intensity pulsed light technique, which provides extreme local heating, is used to sinter the thin film prepared using these nanoparticles on a Mo–glass surface. A uniformly conductive and dense CIGS film can be prepared by adjusting the energy of light and exposure time. The high intensity light irradiation of the CIGS film leads to diffusion of smaller CIGS nanoparticles to form a particle with larger grain size and thus enables sintering of particles without using high temperature processing. - Highlights: • Large scale synthesis of CuIn{sub x}Ga{sub 1−x}Se{sub 2} (CIGS) is reported. • Dodecylamine is used as surfactant and solvent. • CIGS phase formation mechanism is described. • High intensity pulsed light technique is used to sinter the CIGS film.

Influence of post-treatment on properties of Cu(In{sub ,}Ga)Se{sub 2} thin films deposited by RF magnetron sputtering using a quaternary single target for photovoltaic devices

Energy Technology Data Exchange (ETDEWEB)

Jung, Sung Hee; Choi, Soon Ja; Chung, Chee Won, E-mail: cwchung@inha.ac

2014-11-03

The deposition of Cu(In,Ga)Se{sub 2} (CIGS) thin films has been performed by one-step RF sputtering using a single quaternary target and followed by sulfurization to incorporate S into CIGS films. The effect of sulfurization temperature and time on the properties of the films was studied. The sulfurized Cu(In,Ga)(Se,S){sub 2} (CIGSeS) films show that the chalcopyrite peaks shifted to high diffraction angles and the CuS and InS second phases could be formed at low sulfurization temperature. These indicate possible incorporation of S into the films. The formation and disappearance of these second phases depended on the sulfurization temperature and time. The band gap increased with increasing sulfurization temperature and time because of the shift of the absorption edge due to the increase of S/(S + Se) ratio. It was revealed that the resistivity of the as-deposited CIGS film increased after sulfurization while the carrier concentration and mobility decreased. It is believed that the sulfurization process of CIGS films can be utilized as a method to control the properties of the films. - Highlights: • Development of sputtering process of CIGS thin films using single quaternary target • Effect of sulfurization temperature and time on the properties of CIGS films • Application of sulfurization process to improve the properties of CIGS films • Successful transformation of CIGS films to chalcopyrite structure through post-sulfirization.

Complementary Characterization of Cu(In,Ga)Se₂ Thin-Film Photovoltaic Cells Using Secondary Ion Mass Spectrometry, Auger Electron Spectroscopy, and Atom Probe Tomography.

Science.gov (United States)

Jang, Yun Jung; Lee, Jihye; Jeong, Jeung-Hyun; Lee, Kang-Bong; Kim, Donghwan; Lee, Yeonhee

2018-05-01

To enhance the conversion performance of solar cells, a quantitative and depth-resolved elemental analysis of photovoltaic thin films is required. In this study, we determined the average concentration of the major elements (Cu, In, Ga, and Se) in fabricated Cu(In,Ga)Se2 (CIGS) thin films, using inductively coupled plasma atomic emission spectroscopy, X-ray fluorescence, and wavelengthdispersive electron probe microanalysis. Depth profiling results for CIGS thin films with different cell efficiencies were obtained using secondary ion mass spectrometry and Auger electron spectroscopy to compare the atomic concentrations. Atom probe tomography, a characterization technique with sub-nanometer resolution, was used to obtain three-dimensional elemental mapping and the compositional distribution at the grain boundaries (GBs). GBs are identified by Na increment accompanied by Cu depletion and In enrichment. Segregation of Na atoms along the GB had a beneficial effect on cell performance. Comparative analyses of different CIGS absorber layers using various analytical techniques provide us with understanding of the compositional distributions and structures of high efficiency CIGS thin films in solar cells.

Depth Profile of Impurity Phase in Wide-Bandgap Cu(In1-x ,Ga x )Se2 Film Fabricated by Three-Stage Process

Science.gov (United States)

Wang, Shenghao; Nazuka, Takehiro; Hagiya, Hideki; Takabayashi, Yutaro; Ishizuka, Shogo; Shibata, Hajime; Niki, Shigeru; Islam, Muhammad M.; Akimoto, Katsuhiro; Sakurai, Takeaki

2018-02-01

For copper indium gallium selenide [Cu(In1-x ,Ga x )Se2, CIGS]-based solar cells, defect states or impurity phase always form due to both the multinary compositions of CIGS film and the difficulty of controlling the growth process, especially for high Ga concentration. To further improve device performance, it is important to understand such formation of impurity phase or defect states during fabrication. In the work presented herein, the formation mechanism of impurity phase Cu2-δ Se and its depth profile in CIGS film with high Ga content, in particular CuGaSe2 (i.e., CGS), were investigated by applying different growth conditions (i.e., normal three-stage process and two-cycle three-stage process). The results suggest that impurity phase Cu2-δ Se is distributed nonuniformly in the film because of lack of Ga diffusion. The formed Cu2-δ Se can be removed by etching the as-deposited CGS film with bromine-methanol solution, resulting in improved device performance.

Development of CIGS2 thin film solar cells

International Nuclear Information System (INIS)

Dhere, Neelkanth G.; Gade, Vivek S.; Kadam, Ankur A.; Jahagirdar, Anant H.; Kulkarni, Sachin S.; Bet, Sachin M.

2005-01-01

Research and development of CuIn 1-x Ga x Se 2-y S y (CIGSS) thin-film solar cells on ultralightweight flexible metallic foil substrates is being carried out at FSEC PV Materials Lab for space applications. Earlier, the substrate size was limited to 3 cm x 2.5 cm. Large-area sputtering systems and scrubber for hydrogen selenide and sulfide have been designed and constructed for preparation of CIGSS thin-films on large (15 cm x 10 cm) substrates. A selenization/sulfurization furnace donated by Shell (formerly Siemens) Solar has also been refurbished and upgraded. The sputtering target assembly design was modified for proper clamping of targets and effective cooling. A new design of the magnetic assembly for large-area magnetron sputtering sources was implemented so as to achieve uniform deposition on large area. Lightweight stainless steel foil and ultralightweight titanium foil substrates were utilized to increase the specific power of solar cells. Sol-gel derived SiO 2 layers were coated on titanium foil by dip coating method. Deposition parameters for the preparation of molybdenum back contact layers were optimized so as to minimize the residual stress as well as reaction with H 2 S. Presently large (15 cm x 10 cm) CuIn 1-x Ga x S 2 (CIGS2) thin film solar cells are being prepared on Mo-coated titanium and stainless steel foil by sulfurization of CuGa/In metallic precursors in diluted Ar:H 2 S(4%). Heterojunction partner CdS layers are deposited by chemical bath deposition. The regeneration sequence of ZnO/ZnO:Al targets was optimized for obtaining consistently good-quality, transparent and conducting ZnO/ZnO:Al bilayer by RF magnetron-sputter deposition. Excellent facilities at FSEC PV Materials Lab are one of its kinds and could serve as a nucleus of a small pilot plant for CIGSS thin film solar cell fabrication

Boron Doped diamond films as electron donors in photovoltaics: An X-ray absorption and hard X-ray photoemission study

Energy Technology Data Exchange (ETDEWEB)

Kapilashrami, M.; Zegkinoglou, I. [Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Department of Physics, University of Wisconsin Madison, Madison, Wisconsin 53706 (United States); Conti, G.; Nemšák, S.; Conlon, C. S.; Fadley, C. S. [Department of Physics, University of California, Davis, California 95616 (United States); Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Törndahl, T.; Fjällström, V. [Ångström Solar Center, Uppsala University, Box 534, SE-751 21 Uppsala (Sweden); Lischner, J. [Department of Physics, University of California, Berkeley, California 94720 (United States); Louie, Steven G. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Department of Physics, University of California, Berkeley, California 94720 (United States); Hamers, R. J.; Zhang, L. [Department of Chemistry, University of Wisconsin Madison, Madison, Wisconsin 53706 (United States); Guo, J.-H. [Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Himpsel, F. J., E-mail: fhimpsel@wisc.edu [Department of Physics, University of Wisconsin Madison, Madison, Wisconsin 53706 (United States)

2014-10-14

Highly boron-doped diamond films are investigated for their potential as transparent electron donors in solar cells. Specifically, the valence band offset between a diamond film (as electron donor) and Cu(In,Ga)Se₂ (CIGS) as light absorber is determined by a combination of soft X-ray absorption spectroscopy and hard X-ray photoelectron spectroscopy, which is more depth-penetrating than standard soft X-ray photoelectron spectroscopy. In addition, a theoretical analysis of the valence band is performed, based on GW quasiparticle band calculations. The valence band offset is found to be small: VBO=VBM{sub CIGS} – VBM{sub diamond}=0.3 eV±0.1 eV at the CIGS/Diamond interface and 0.0 eV±0.1 eV from CIGS to bulk diamond. These results provide a promising starting point for optimizing the band offset by choosing absorber materials with a slightly lower valence band maximum.

Preparation and optimization of a molybdenum electrode for CIGS solar cells

Directory of Open Access Journals (Sweden)

Feng Jingxue

2016-11-01

Full Text Available Molybdenum (Mo films were deposited by radio frequency (RF, direct current (DC and mixed magnetron sputtering, respectively. With changing the deposition parameters including deposition pressure and power, the films show different surface morphology and crystallinity. Lower resistivity of the films is obtained in the DC mode and better reflectivity of the films is obtained in the RF mode. It is shown that the crystallinity increases when the deposition pressure decreases. The crystallinity and the grain size both increase as the deposition power increasing. The lowest resistivity of the single Mo film is 34×10-6 Ω·cm when the deposition pressure is 0.1 Pa and the deposition power is 300 W in the DC mode. In order to obtain lower resistivity, better adhesion and better reflectivity, bilayer films and tri-layer films were both deposited in different mode. They all show good adhesion and low resistivity. The Mo films deposited in mixed mode show better reflectivity. It is demonstrated that the resistivity of about 65×10-6 Ω·cm is achieved in DC/RF mode and the resistivity of about 61×10-6 Ω·cm is achieved in RF/DC/RF mode. And the tri-layer films achieved in RF/DC/RF mode have better reflectivity than bilayer films achieved in DC/RF mode. The tri-layer films achieved in RF/DC/RF mode is appropriate for using as the electrode of CIGS solar cells.

Bismuth-doped Cu(In,Ga)Se{sub 2} absorber prepared by multi-layer precursor method and its solar cell

Energy Technology Data Exchange (ETDEWEB)

Chantana, Jakapan; Hironiwa, Daisuke; Minemoto, Takashi [Department of Electrical and Electronic Engineering, Ritsumeikan University, 1-1-1 Nojihigashi, Kusatsu, Shiga 525-8577 (Japan); Watanabe, Taichi; Teraji, Seiki; Kawamura, Kazunori [Environment and Energy Research Center, Nitto Denko Corporation, 2-8 Yamadaoka, Suita, Osaka 565-0871 (Japan)

2015-06-15

Bismuth (Bi)-doped Cu(In,Ga)Se{sub 2} (CIGS) films were prepared by the so-called ''multi-layer precursor method'', obtained by depositing them onto Bi layers with various thicknesses on Mo-coated soda-lime glass (SLG) substrates. Material composition (Cu, In, Ga, and Se) profiles of the CIGS films are almost identical, whereas sodium (Na) is reduced, when Bi thickness is increased. Moreover, the incorporation of Bi into the CIGS film is enhanced with thicker Bi layer. With Bi thickness from 0 to 70 nm, the 2.4-μm-thick CIGS absorbers demonstrate the increase in CIGS grain size, carrier lifetime, and carrier concentration, thus improving their cell performances, especially open-circuit voltage (V{sub OC}). With further increase in Bi thickness of above 70 nm, the CIGS films show the deterioration of CIGS film quality owing to the formation of Bi compounds such as Bi, BiSe, and Bi{sub 4}Se{sub 3}. Consequently, Bi-doped CIGS absorber with thickness of 2.4 μm, prepared with the 70-nm-thick Bi layer on Mo-coated SLG substrate, gives rise to the improvement of photovoltaic performances, especially V{sub OC}. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Bismuth-doped Cu(In,Ga)Se2 absorber prepared by multi-layer precursor method and its solar cell

International Nuclear Information System (INIS)

Chantana, Jakapan; Hironiwa, Daisuke; Minemoto, Takashi; Watanabe, Taichi; Teraji, Seiki; Kawamura, Kazunori

2015-01-01

Bismuth (Bi)-doped Cu(In,Ga)Se 2 (CIGS) films were prepared by the so-called ''multi-layer precursor method'', obtained by depositing them onto Bi layers with various thicknesses on Mo-coated soda-lime glass (SLG) substrates. Material composition (Cu, In, Ga, and Se) profiles of the CIGS films are almost identical, whereas sodium (Na) is reduced, when Bi thickness is increased. Moreover, the incorporation of Bi into the CIGS film is enhanced with thicker Bi layer. With Bi thickness from 0 to 70 nm, the 2.4-μm-thick CIGS absorbers demonstrate the increase in CIGS grain size, carrier lifetime, and carrier concentration, thus improving their cell performances, especially open-circuit voltage (V OC ). With further increase in Bi thickness of above 70 nm, the CIGS films show the deterioration of CIGS film quality owing to the formation of Bi compounds such as Bi, BiSe, and Bi 4 Se 3 . Consequently, Bi-doped CIGS absorber with thickness of 2.4 μm, prepared with the 70-nm-thick Bi layer on Mo-coated SLG substrate, gives rise to the improvement of photovoltaic performances, especially V OC . (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Funcionamiento hidrológico de un humedal ribereño, el Masegar, en el conjunto de los humedales de La Mancha Húmeda de la cuenca alta del rió Cigüela

Directory of Open Access Journals (Sweden)

Llamas, M. R.

1995-12-01

Full Text Available Fifteen years ago «La Mancha Húmeda» was deelared Biosphere Reserve by UNESCO, at the request of the Spanish Government. According to a recent deelaration by UNESCO in 1995, such title could be lost if the degradation processes of the wetlands of «La Mancha Húmeda» continue. «La Mancha Húmeda» was formed by a hundred of small lakes or wetlands that in area totalled about 200-300 km2 and they were distributed over an area of about 25.000 km2. These are different types of wetlands (saltwater and freshwater, permanent and ephimeral, riparian and closed basins, etc.. It is estimated that the actual surface of all the wetlands is about 20-30% of that occupied 20 or 30 years ago. The most famous degradation case is that of the «Tablas de Daimiel National Park» that has shrinked fram an area of about 15-20km2 to less than 1 km2 This article presents the general situation of the riverine wetlands of the Cigüela river and the results of the hydrological functioning of a wetland of modest dimensions, less than 1 km2, El Masegar. It is a riparian wetland located in the Cigüela River basin which has been severely affected by man actions. El Masegar can be considered as an artificial wetland. From an ecological point of view, this wetland seems to have been functioning in a proper way until 1988, when the so called «Plan de Regeneración Hídrica del Parque Nacional de las Tablas de Daimiel» began. This Plan has not regenerated the Natural Park but has degradated or destroyed the riparian wetlands that existed along the Cigüela River valley which is about ISO km long. The surface of these wetlands all together was larger than that of Tablas de Daimiel National Park. The study shows that it could be feasible to restore or maintain most of the riparian wetlands of the «La Mancha Húmeda» without a great economic investment and without social conflicts with the farmers.En 1981, a petición del Gobierno español, la

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture next-generation thin film solar cells, development of technologies to manufacture CIS solar cell modules, development of technologies to increase high-quality film area; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu, CIS taiyo denchi module no seizo gijutsu kaihatsu, kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With an objective to improve efficiency and reduce cost of CIS-based thin film solar cells, research and development has been made on technologies to increase high-quality CIS film area and technologies to increase speed in the manufacturing process. This paper describes the achievements attained during fiscal 1997. The research covered development of technologies to form high-grade Cu (In, Ga) Se{sub 2} (CIGS) film by using the multi-dimensional deposition process, component technologies for forming a rear electrode, a buffer layer and a transparent electrode, and patterning technologies. As a result of the research, thickness of the CIGS film was reduced to half as much as that of the conventional films, having achieved conversion efficiency of 13.1%, which corresponds to about 90% of the conventional CIGS solar cells. In addition, elucidation was made on the effect of an MoSe{sub 2} layer existing on interface with CIGS/Mo in a CIGS solar cell imposed on solar cell characteristics. In developing an Mo film laser scribing technology, intensity dependence of laser energy was made clear, the energy being required for scribing according to surface condition of the Mo film. (NEDO)

Boron Doped diamond films as electron donors in photovoltaics: An X-ray absorption and hard X-ray photoemission study

International Nuclear Information System (INIS)

Kapilashrami, M.; Zegkinoglou, I.; Conti, G.; Nemšák, S.; Conlon, C. S.; Fadley, C. S.; Törndahl, T.; Fjällström, V.; Lischner, J.; Louie, Steven G.; Hamers, R. J.; Zhang, L.; Guo, J.-H.; Himpsel, F. J.

2014-01-01

Highly boron-doped diamond films are investigated for their potential as transparent electron donors in solar cells. Specifically, the valence band offset between a diamond film (as electron donor) and Cu(In,Ga)Se 2 (CIGS) as light absorber is determined by a combination of soft X-ray absorption spectroscopy and hard X-ray photoelectron spectroscopy, which is more depth-penetrating than standard soft X-ray photoelectron spectroscopy. In addition, a theoretical analysis of the valence band is performed, based on GW quasiparticle band calculations. The valence band offset is found to be small: VBO = VBM CIGS – VBM diamond  = 0.3 eV ± 0.1 eV at the CIGS/Diamond interface and 0.0 eV ± 0.1 eV from CIGS to bulk diamond. These results provide a promising starting point for optimizing the band offset by choosing absorber materials with a slightly lower valence band maximum.

Lung Toxicity of Condensed Aerosol from E-CIG Liquids: Influence of the Flavor and the In Vitro Model Used

Directory of Open Access Journals (Sweden)

Rossella Bengalli

2017-10-01

Full Text Available The diffusion of e-cigarette (e-CIG opens a great scientific and regulatory debate about its safety. The huge number of commercialized devices, e-liquids with almost infinite chemical formulations and the growing market demand for a rapid and efficient toxicity screen system that is able to test all of these references and related aerosols. A consensus on the best protocols for the e-CIG safety assessment is still far to be achieved, since the huge number of variables characterizing these products (e.g., flavoring type and concentration, nicotine concentration, type of the device, including the battery and the atomizer. This suggests that more experimental evidences are needed to support the regulatory frameworks. The present study aims to contribute in this field by testing the effects of condensed aerosols (CAs from three main e-liquid categories (tobacco, mint, and cinnamon as food-related flavor, with (18 mg/mL or without nicotine. Two in vitro models, represented by a monoculture of human epithelial alveolar cells and a three-dimensional (3D co-culture of alveolar and lung microvascular endothelial cells were used. Cell viability, pro-inflammatory cytokines release and alveolar-blood barrier (ABB integrity were investigated as inhalation toxicity endpoints. Results showed that nicotine itself had almost no influence on the modulation of the toxicity response, while flavor composition did have. The cell viability was significantly decreased in monoculture and ABB after exposure to the mints and cinnamon CAs. The barrier integrity was significantly affected in the ABB after exposure to cytotoxic CAs. With the exception of the significant IL-8 release in the monoculture after Cinnamon exposure, no increase of inflammatory cytokines (IL-8 and MCP-1 release was observed. These findings point out that multiple assays with different in vitro models are able to discriminate the acute inhalation toxicity of CAs from liquids with different flavors

Cu(InGa)Se{sub 2} absorber formation by in-situ, low-temperature annealing of co-evaporated bilayer (InGa){sub 2}Se{sub 3}/CuSe precursors

Energy Technology Data Exchange (ETDEWEB)

Moon, Kyeongchan; Kim, Woo Kyoung, E-mail: wkim@ynu.ac.kr

2015-12-01

Chalcopyrite Cu(InGa)Se{sub 2} (CIGS) absorbers were fabricated by the formation of bilayer stacked glass/Mo/(InGa){sub 2}Se{sub 3}/CuSe precursors followed by in-situ thermal annealing at 450 °C for approximately 10 min in a vacuum evaporator. The material properties (e.g., crystal orientation, compositional depth profile, and overall composition) and device performance of the resulting CIGS absorbers were compared with those of the CIGS absorbers formed by conventional 1-stage and 3-stage CIGS formation processes at a similar temperature. X-ray diffraction confirmed that the 1-stage co-evaporation and in-situ annealing of the bilayer precursor produced a polycrystalline CIGS absorber without a specific texture, whereas the CIGS absorber formed by the 3-stage process showed a highly (220) preferred orientation. Secondary ion mass spectrometry revealed Ga accumulation at the bottom of CIGS formed by in-situ annealing of the bilayer precursors. The cell efficiency of the device with the CIGS absorber formed by the in-situ, low-temperature (450 °C) annealing of bilayer stacked glass/Mo/(InGa){sub 2}Se{sub 3}/CuSe precursors was comparable to that produced by the conventional 3-stage process at a similar temperature. - Highlights: • Annealing of (InGa){sub 2}Se{sub 3}/CuSe precursors was compared with coevaporation process. • In-situ annealing of (InGa){sub 2}Se{sub 3}/CuSe precursors at 450 °C produced about 9% solar cell. • Ga profile within Cu(InGa)Se{sub 2} depended on process profile during co-evaporation.

A Comprehensive Study of One-Step Selenization Process for Cu(In1-x Ga x )Se2 Thin Film Solar Cells.

Science.gov (United States)

Chen, Shih-Chen; Wang, Sheng-Wen; Kuo, Shou-Yi; Juang, Jenh-Yih; Lee, Po-Tsung; Luo, Chih Wei; Wu, Kaung-Hsiung; Kuo, Hao-Chung

2017-12-01

In this work, aiming at developing a rapid and environmental-friendly process for fabricating CuIn 1-x Ga x Se 2 (CIGS) solar cells, we demonstrated the one-step selenization process by using selenium vapor as the atmospheric gas instead of the commonly used H 2 Se gas. The photoluminescence (PL) characteristics indicate that there exists an optimal location with superior crystalline quality in the CIGS thin films obtained by one-step selenization. The energy dispersive spectroscopy (EDS) reveals that the Ga lateral distribution in the one-step selenized CIGS thin film is intimately correlated to the blue-shifted PL spectra. The surface morphologies examined by scanning electron microscope (SEM) further suggested that voids and binary phase commonly existing in CIGS films could be successfully eliminated by the present one-step selenization process. The agglomeration phenomenon attributable to the formation of MoSe 2 layer was also observed. Due to the significant microstructural improvement, the current-voltage (J-V) characteristics and external quantum efficiency (EQE) of the devices made of the present CIGS films have exhibited the remarkable carrier transportation characteristics and photon utilization at the optimal location, resulting in a high conversion efficiency of 11.28%. Correlations between the defect states and device performance of the one-step selenized CIGS thin film were convincingly delineated by femtosecond pump-probe spectroscopy.

Investigations into alterntive substrate, absorber, and buffer layer processing for Cu(In,Ga)Se{sub 2}-based solar cells

Energy Technology Data Exchange (ETDEWEB)

Tuttle, J.R.; Berens, T.A.; Keane, J. [National Renewable Energy Lab., Golden, CO (United States)] [and others

1996-05-01

High-performance Cu(In,Ga)Se{sub 2}(CIGS)-based solar cells are presently fabricated within a narrow range of processing options. In this contribution, alternative substrate, absorber, and buffer layer processing is considered. Cell performance varies considerably when alternative substrates are employed. These variations are narrowed with the addition of Na via a Na{sub 2}S compound. Sputtered and electrodeposited CIGS precursors and completed absorbers show promise as alternatives to evaporation. A recrystallization process is required to improve their quality. (In,Ga){sub y}Se buffer layers contribute to cell performance above 10. Further improvements in these alternatives will lead to combined cell performance greater than 10% in the near term.

An International Peer Review of the Safety Options Dossier of the Project for Disposal of Radioactive Waste in Deep Geological Formations (Cigéo). Final Report of the IAEA International Review Team November 2016

International Nuclear Information System (INIS)

2017-07-01

The French Nuclear Safety Authority (Autorité de sûreté nucléaire, ASN) is preparing the evaluation of a licence application for the creation of a deep geological disposal facility in 2018, called Cigéo, for intermediate level, high level and long lived radioactive waste. This licence is preceded by the submission of a Safety Options Dossier to ASN, which provides the French National Radioactive Waste Management Agency (Agence nationale pour la gestion des déchets radioactifs, Andra) the possibility to receive advice from ASN on the preparation of the licence application on the safety principles and approach. The Safety Options Dossier sets out the chosen objectives, concepts and principles for ensuring the safety of the facility. ASN requested the IAEA to organize an international peer review of the Safety Options Dossier. This publication presents the consensus view of the international group of experts convened by the IAEA to conduct the review against the relevant IAEA safety standards and proven international practice and experience. The experts acted in a personal capacity and the views expressed do not necessarily reflect those of the IAEA, the governments of the nominating Member States or the nominating organizations. The basis of this peer review is the set of documents provided by Andra, as the agency responsible for the development of the Cigéo project and for its safety. Consequently, the findings of the reviews are addressed directly to Andra. This publication, however, is primarily submitted to ASN to review the outcomes of the Andra project.

Effect of zinc addition on properties of cadmium sulfide layer and performance of Cu(In,Ga)Se2 solar cell

International Nuclear Information System (INIS)

Bae, Dowon; Gho, Junghwan; Shin, Minjung; Kwon, Sehan

2013-01-01

Cd (1−x) Zn x S (CdS:Zn) thin films were grown on an indium tin oxide-coated glass substrate and Cu(In,Ga)Se 2 (CIGS) surface by chemical bath deposition for solar cell applications, and their composition, and optical properties were studied to decide the optimum process conditions for buffer layer growth. The average conversion efficiency of CIGS solar panels (24-in.) with the CdS:Zn layer was 0.35% higher than that of conventional solar panels mainly because of the increased open-circuit voltage. This efficiency improvement was not due to modification of the optical properties of the buffer layer, but due to the change in the deposition rate during buffer layer growth. - Highlights: ► CdS:Zn buffer layers were fabricated for Cu(In,Ga)Se 2 (CIGS) photovoltaic (PV) panels. ► Composition of buffer layers on indium–tin–oxide (ITO) and CIGS was investigated. ► Transmittance of CdS:Zn on ITO coated glass showed 5% higher than CdS. ► Efficiency of CdS:Zn solution adopted panels showed 0.47% higher than that with CdS. ► However, it was revealed that only Cd and S ions were found at the surface of CIGS

Substrate temperature optimization for Cu(In, Ga)Se{sub 2} solar cells on flexible stainless steels

Energy Technology Data Exchange (ETDEWEB)

Liang, X.; Zhu, H.; Chen, J., E-mail: chenjingwei@126.com; Zhou, D.; Zhang, C.; Guo, Y.; Niu, X.; Li, Z.; Mai, Y., E-mail: yaohuamai@hbu.edu.cn

2016-04-15

Graphical abstract: - Highlights: • CIGS thin films are deposited on flexible SS substrates at different substrate temperatures. • CIGS thin films deposited at different T{sub S2} show different Ga/(Ga + In) ratio profiles. • All CIGS thin films show (112) and (220/204) preferred orientations with a shift to higher angles. • Conversion efficiency of 11.3% is obtained for CIGS solar cells deposited at 500 °C. - Abstract: Cu(In, Ga)Se{sub 2} (CIGS) thin films are deposited on flexible stainless steel (SS) substrates using the so called 3-stage co-evaporation process at different substrate temperatures ranging from 440 °C to 640 °C during the 2nd stage and the 3rd stage (T{sub S2}). The effects of T{sub S2} on the properties of CIGS thin films are systematically investigated. It is found by secondary ion mass spectrometry measurement that CIGS thin films deposited at different T{sub S2} show different Ga/(Ga + In) ratio (GGI) profiles along the growth direction. High T{sub S2} facilitates the grain growth and leads to larger grain size. However, high T{sub S2} worsens the spectral response of CIGS solar cells in the long wavelength range, which is partly attributed to the too much iron atom diffusion from the SS substrates into the CIGS thin films. All CIGS thin films show (112) preferred orientations with a shift to higher angle due to variation of compositions. A shoulder-like two-peak structure of (112) and (220/204) peaks appears for CIGS thin films deposited at lower T{sub S2}. Conversion efficiency of 11.3% is obtained for CIGS thin film solar cells deposited at the T{sub S2} of 500 °C.

Adhesion Improvement and Characterization of Magnetron Sputter Deposited Bilayer Molybdenum Thin Films for Rear Contact Application in CIGS Solar Cells

Directory of Open Access Journals (Sweden)

Weimin Li

2016-01-01

Full Text Available Molybdenum (Mo thin films are widely used as rear electrodes in copper indium gallium diselenide (CIGS solar cells. The challenge in Mo deposition by magnetron sputtering lies in simultaneously achieving good adhesion to the substrates while retaining the electrical and optical properties. Bilayer Mo films, comprising five different thickness ratios of a high pressure (HP deposited bottom layer and a low pressure (LP deposited top layer, were deposited on 40 cm × 30 cm soda-lime glass substrates by DC magnetron sputtering. We focus on understanding the effects of the individual layer properties on the resulting bilayer Mo films, such as microstructure, surface morphology, and surface oxidation. We show that the thickness of the bottom HP Mo layer plays a major role in determining the micromechanical and physical properties of the bilayer Mo stack. Our studies reveal that a thicker HP Mo bottom layer not only improves the adhesion of the bilayer Mo, but also helps to improve the film crystallinity along the preferred [110] direction. However, the surface roughness and the porosity of the bilayer Mo films are found to increase with increasing bottom layer thickness, which leads to lower optical reflectance and a higher probability for oxidation at the Mo surface.

Effect of zinc addition on properties of cadmium sulfide layer and performance of Cu(In,Ga)Se{sub 2} solar cell

Energy Technology Data Exchange (ETDEWEB)

Bae, Dowon, E-mail: bae.dowon@yahoo.co.kr; Gho, Junghwan; Shin, Minjung; Kwon, Sehan

2013-05-01

Cd{sub (1−x)}Zn{sub x}S (CdS:Zn) thin films were grown on an indium tin oxide-coated glass substrate and Cu(In,Ga)Se{sub 2} (CIGS) surface by chemical bath deposition for solar cell applications, and their composition, and optical properties were studied to decide the optimum process conditions for buffer layer growth. The average conversion efficiency of CIGS solar panels (24-in.) with the CdS:Zn layer was 0.35% higher than that of conventional solar panels mainly because of the increased open-circuit voltage. This efficiency improvement was not due to modification of the optical properties of the buffer layer, but due to the change in the deposition rate during buffer layer growth. - Highlights: ► CdS:Zn buffer layers were fabricated for Cu(In,Ga)Se{sub 2} (CIGS) photovoltaic (PV) panels. ► Composition of buffer layers on indium–tin–oxide (ITO) and CIGS was investigated. ► Transmittance of CdS:Zn on ITO coated glass showed 5% higher than CdS. ► Efficiency of CdS:Zn solution adopted panels showed 0.47% higher than that with CdS. ► However, it was revealed that only Cd and S ions were found at the surface of CIGS.

Local current-voltage behaviors of preferentially and randomly textured Cu(In,Ga)Se2 thin films investigated by conductive atomic force microscopy

International Nuclear Information System (INIS)

Shin, R.H.; Jo, W.; Kim, D.W.; Yun, Jae Ho; Ahn, S.

2011-01-01

Electrical transport properties on polycrystalline Cu(In,Ga)Se 2 (CIGS) (Ga/(In+Ga) ∼35%) thin films were examined by conductive atomic force microscopy. The CIGS thin films with a (112) preferential or random texture were deposited on Mo-coated glass substrates. Triangular pyramidal grain growths were observed in the CIGS thin films preferentially textured to the (112) planes. Current maps of the CIGS surface were acquired with a zero or non-zero external voltage bias. The contrast of the images on the grain boundaries and intragrains displayed the conduction path in the materials. Local current-voltage measurements were performed to evaluate the charge conduction properties of the CIGS thin films. (orig.)

Local current-voltage behaviors of preferentially and randomly textured Cu(In,Ga)Se{sub 2} thin films investigated by conductive atomic force microscopy

Energy Technology Data Exchange (ETDEWEB)

Shin, R.H.; Jo, W. [Ewha Womans University, Department of Physics, Seoul (Korea, Republic of); Kim, D.W. [Ewha Womans University, Department of Physics, Seoul (Korea, Republic of); Ewha Womans University, Department of Chemistry and Nanosciences, Seoul (Korea, Republic of); Yun, Jae Ho; Ahn, S. [Korea Institute of Energy Research, Daejeon (Korea, Republic of)

2011-09-15

Electrical transport properties on polycrystalline Cu(In,Ga)Se{sub 2} (CIGS) (Ga/(In+Ga) {approx}35%) thin films were examined by conductive atomic force microscopy. The CIGS thin films with a (112) preferential or random texture were deposited on Mo-coated glass substrates. Triangular pyramidal grain growths were observed in the CIGS thin films preferentially textured to the (112) planes. Current maps of the CIGS surface were acquired with a zero or non-zero external voltage bias. The contrast of the images on the grain boundaries and intragrains displayed the conduction path in the materials. Local current-voltage measurements were performed to evaluate the charge conduction properties of the CIGS thin films. (orig.)

Semi-transparent photovoltaic glazing based on electrodeposited CIGS solar cells on patterned molybdenum/glass substrates

Science.gov (United States)

Sidali, Tarik; Bou, Adrien; Coutancier, Damien; Chassaing, Elisabeth; Theys, Bertrand; Barakel, Damien; Garuz, Richard; Thoulon, Pierre-Yves; Lincot, Daniel

2018-03-01

In this paper, a new way of preparing semi-transparent solar cells using Cu(In1-xGax)Se2 (CIGS) chalcopyrite semiconductors as absorbers for BIPV applications is presented. The key to the elaboration process consists in the co-electrodeposition of Cu-In-Ga mixed oxides on submillimetric hole-patterned molybdenum substrate, followed by thermal reduction to metallic alloys and selenisation. This method has the advantage of being a selective deposition technique where the thin film growth is carried out only on Mo covered areas. Thus, after annealing, the transparency of the sample is always preserved, allowing light to pass through the device. A complete device (5 × 5 cm2) with 535 μm diameter holes and total glass aperture of around 35% shows an open circuit voltage (VOC) of 400 mV. Locally, the I-V curves reveal a maximum efficiency of 7.7%, VOC of 460 mV, JSC of 24 mA.cm-2 in an area of 0.1 cm2 with 35% aperture. This efficiency on the semi-transparent area is equivalent to a record efficiency of 11.9% by taking into account only the effective area.

Deep absorption band in Cu(In,Ga)Se{sub 2} thin films and solar cells observed by transparent piezoelectric photothermal spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Shirakata, Sho; Atarashi, Akiko [Faculty of Engineering, Ehime University, Matsuyama 790-8577 (Japan); Yagi, Masakazu [Kagawa National College of Technology, Mitoyo-shi 769-1192 (Japan)

2015-06-15

The photo-acoustic spectroscopy (PAS) using a transparent piezoelectric photo-thermal (Tr-PPT) method was carried out on Cu(In,Ga)Se{sub 2} (CIGS) thin films (both CIGS/Mo/SLG and CdS/CIGS/Mo/SLG) and solar cells (ZnO/CdS/CIGS/Mo/SLG). Using the Tr-PPT method, the high background absorption in the below gap region observed in both a microphone and a conventional transducer PAS spectra was strongly reduced. This high background absorption came from the CIGS/Mo interface. This result proves that the Tr-PPT PAS is the surface sensitive method. In the below-band region, a bell-shape deep absorption band has been observed at 0.76 eV, in which a full-width at the half-maximum value was 70-120 meV. This deep absorption band was observed for both CdS/CIGS/Mo/SLG and ZnO/CdS/CIGS/Mo/SLG structures. The peak energy of the absorption band was independent of the alloy composition for 0.25≤Ga/III≤0.58. Intensity of the PA signal was negatively correlated to the Na concentration at the CIGS film surface. The origin of the 0.76 eV peak is discussed with relation to native defects such as a Cu-vacancy-related defect (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Hydrogenated indium oxide window layers for high-efficiency Cu(In,Ga)Se2 solar cells

International Nuclear Information System (INIS)

Jäger, Timo; Romanyuk, Yaroslav E.; Nishiwaki, Shiro; Bissig, Benjamin; Pianezzi, Fabian; Fuchs, Peter; Gretener, Christina; Tiwari, Ayodhya N.; Döbeli, Max

2015-01-01

High mobility hydrogenated indium oxide is investigated as a transparent contact for thin film Cu(In,Ga)Se 2 (CIGS) solar cells. Hydrogen doping of In 2 O 3 thin films is achieved by injection of H 2 O water vapor or H 2 gas during the sputter process. As-deposited amorphous In 2 O 3 :H films exhibit a high electron mobility of ∼50 cm 2 /Vs at room temperature. A bulk hydrogen concentration of ∼4 at. % was measured for both optimized H 2 O and H 2 -processed films, although the H 2 O-derived film exhibits a doping gradient as detected by elastic recoil detection analysis. Amorphous IOH films are implemented as front contacts in CIGS based solar cells, and their performance is compared with the reference ZnO:Al electrodes. The most significant feature of IOH containing devices is an enhanced open circuit voltage (V OC ) of ∼20 mV regardless of the doping approach, whereas the short circuit current and fill factor remain the same for the H 2 O case or slightly decrease for H 2 . The overall power conversion efficiency is improved from 15.7% to 16.2% by substituting ZnO:Al with IOH (H 2 O) as front contacts. Finally, stability tests of non-encapsulated solar cells in dry air at 80 °C and constant illumination for 500 h demonstrate a higher stability for IOH-containing devices

Adhesion, resistivity and structural, optical properties of molybdenum on steel sheet coated with barrier layer done by sol–gel for CIGS solar cells

Energy Technology Data Exchange (ETDEWEB)

Amouzou, Dodji, E-mail: dodji.amouzou@fundp.ac.be [Research Centre in Physics of Matter and Radiation (PMR), University of Namur (FUNDP), Rue de Bruxelles 61, 5000 Namur (Belgium); Dumont, Jacques [Research Centre in Physics of Matter and Radiation (PMR), University of Namur (FUNDP), Rue de Bruxelles 61, 5000 Namur (Belgium); Fourdrinier, Lionel; Richir, Jean-Baptiste; Maseri, Fabrizio [CRM-Group, Boulevard de Colonster, B 57, 4000 Liège (Belgium); Sporken, Robert [Research Centre in Physics of Matter and Radiation (PMR), University of Namur (FUNDP), Rue de Bruxelles 61, 5000 Namur (Belgium)

2013-03-01

Molybdenum films are investigated on stainless steel substrates coated with polysilazane based sol–gel and SiO{sub x} layers for flexible CIGS solar cell applications. Thermal stability of the multilayer has been studied. The thickness of polysilazane films are significantly reduced (17%) after heat treatment suggesting a thermal degradation. Four different microstructures were found for Mo films by varying argon total pressure from 2.6 × 10{sup −1} Pa to 2.6 Pa. It was shown that continuous films, low sheet resistance (0.5 Ω/□) and well facetted grains can be achieved when Mo films are deposited on heated substrates at homologous temperature, T of 0.2. - Highlights: ► Steel sheet is functionalized for Cu[Inx,Ga(1 − x)Se2] solar cells. ► Varying deposition pressure impacts the microstructure of Mo films. ► High thermal stability of the sol gel based barrier layer has been investigated. ► Low sheet resistance and continuous Mo films have been obtained at 550°C. ► Thermal stability of functionalized steel sheets at 550°C has been investigated.

Comparison of Cu(In, Ga)Se{sub 2} thin films deposited on different preferred oriented Mo back contact by RF sputtering from a quaternary target

Energy Technology Data Exchange (ETDEWEB)

Tian, Jing [Sichuan University, College of Materials Science and Engineering, Chengdu (China); Solar Energy Research Institute, Yunnan Normal University, Education Ministry Key Laboratory of Renewable Energy Advanced Materials and Manufacturing Technology, Kunming (China); Peng, Lianqin; Chen, Jinwei; Wang, Gang; Wang, Xueqin; Kang, Hong; Wang, Ruilin [Sichuan University, College of Materials Science and Engineering, Chengdu (China)

2014-09-15

The Cu(In, Ga)Se{sub 2} (CIGS) thin films were deposited on bare glass and DC sputtered preferential oriented Mo-coated glass by RF sputtering from a single quaternary target. The structural and morphological properties of the films were characterized by X-ray diffraction (XRD), Raman spectroscope, energy dispersive X-ray spectrometer (EDS) and atomic force microscope (AFM). Preferred orientation of the Mo back contact was tuned between (110) and (211) plane by controlling the thickness. All the deposited CIGS thin films show (112) preferred oriented chalcopyrite structures. The films prepared on Mo-coated glass show higher quality crystallinity, better stoichiometry composition and more smooth surface morphology. Especially, the film on (211) oriented Mo-coated glass with the best integrated performance is expected to be a candidate absorber for high-efficiency CIGS solar cell device. (orig.)

Degradation analysis of thin film photovoltaic modules

International Nuclear Information System (INIS)

Radue, C.; Dyk, E.E. van

2009-01-01

Five thin film photovoltaic modules were deployed outdoors under open circuit conditions after a thorough indoor evaluation. Two technology types were investigated: amorphous silicon (a-Si:H) and copper indium gallium diselenide (CIGS). Two 14 W a-Si:H modules, labelled Si-1 and Si-2, were investigated. Both exhibited degradation, initially due to the well-known light-induced degradation described by Staebler and Wronski [Applied Physics Letters 31 (4) (1977) 292], and thereafter due to other degradation modes such as cell degradation. The various degradation modes contributing to the degradation of the a-Si:H modules will be discussed. The initial maximum power output (P MAX ) of Si-1 was 9.92 W, with the initial light-induced degradation for Si-1 ∼30% and a total degradation of ∼42%. For Si-2 the initial P MAX was 7.93 W, with initial light-induced degradation of ∼10% and a total degradation of ∼17%. Three CIGS modules were investigated: two 20 W modules labelled CIGS-1 and CIGS-2, and a 40 W module labelled CIGS-3. CIGS-2 exhibited stable performance while CIGS-1 and CIGS-3 exhibited degradation. CIGS is known to be stable over long periods of time, and thus the possible reasons for the degradation of the two modules are discussed.

Degradation analysis of thin film photovoltaic modules

Energy Technology Data Exchange (ETDEWEB)

Radue, C., E-mail: chantelle.radue@nmmu.ac.z [Department of Physics, PO Box 77000, Nelson Mandela Metropolitan University, Port Elizabeth 6031 (South Africa); Dyk, E.E. van [Department of Physics, PO Box 77000, Nelson Mandela Metropolitan University, Port Elizabeth 6031 (South Africa)

2009-12-01

Five thin film photovoltaic modules were deployed outdoors under open circuit conditions after a thorough indoor evaluation. Two technology types were investigated: amorphous silicon (a-Si:H) and copper indium gallium diselenide (CIGS). Two 14 W a-Si:H modules, labelled Si-1 and Si-2, were investigated. Both exhibited degradation, initially due to the well-known light-induced degradation described by Staebler and Wronski [Applied Physics Letters 31 (4) (1977) 292], and thereafter due to other degradation modes such as cell degradation. The various degradation modes contributing to the degradation of the a-Si:H modules will be discussed. The initial maximum power output (P{sub MAX}) of Si-1 was 9.92 W, with the initial light-induced degradation for Si-1 approx30% and a total degradation of approx42%. For Si-2 the initial P{sub MAX} was 7.93 W, with initial light-induced degradation of approx10% and a total degradation of approx17%. Three CIGS modules were investigated: two 20 W modules labelled CIGS-1 and CIGS-2, and a 40 W module labelled CIGS-3. CIGS-2 exhibited stable performance while CIGS-1 and CIGS-3 exhibited degradation. CIGS is known to be stable over long periods of time, and thus the possible reasons for the degradation of the two modules are discussed.

Nanosolar: Delivering Grid-Parity Solar Electricity

Energy Technology Data Exchange (ETDEWEB)

Sager, Brian [Nanosolar, Inc., San Jose, CA (United States)

2012-05-31

Nanosolar has developed proprietary technology based on Copper-Indium-Gallium-diSelenide (CIGS) absorber technology that allows the printing of this semiconductor material using a high-speed, high-throughput roll-to-roll manufacturing process. A central challenge in cost-effectively constructing a large-area CIGS-based solar cell or module is that the elements of the CIGS layer must be within a narrow stoichiometric ratio on nano-, meso-, and macroscopic length scale in all three dimensions in order for the resulting cell or module to be highly efficient. Achieving precise stoichiometric composition over relatively large substrate areas is however difficult using traditional vacuum-based deposition processes. For example, it is difficult to uniformly deposit compounds and/or alloys containing more than one element by sputtering or evaporation. Both techniques rely on deposition approaches that are limited to line-of-sight and limited-area sources, tending to result in poor surface coverage. Line-of-sight trajectories and limited-area sources can result in non-uniform three-dimensional distribution of the elements in all three dimensions and/or poor film-thickness uniformity over large areas. These non-uniformities can occur over the nano-, meso-, and/or macroscopic scales. Such non-uniformity also alters the local stoichiometric ratios of the absorber layer, decreasing the potential power conversion efficiency of the complete cell or module. Nanosolar has overcome these challenges by printing nanoparticulate CIGS precursor materials onto low-cost metal foil substrates, and performing a rapid thermal processing to convert the nanoparticulate coating into a CIGS absorber layer By locking in the appropriate stochiometry into the nanoparticulate precursor material, spatial uniformity is ensured in the coated layers, while printing at high speed and throughput minimizes solar cell cost.

Site selective doping of Zn for the p-type Cu(In,Ga)Se{sub 2} thin film for solar cell application

Energy Technology Data Exchange (ETDEWEB)

Shirakata, Sho [Faculty of Engineering, Ehime University, Matsuyama 790-8577 (Japan); Tokyo University of Science, Research Institute for Science and Technology, Noda, Chiba 278-8510 (Japan)

2017-06-15

Selective doping of a Zn impurity at the group III site in a Cu(In, Ga)Se{sub 2} (CIGS) film was performed by the doping of Zn at the first stage of the three-stage method. The p-type CIGS:Zn film was obtained, which is in contrast to the n-type CIGS:Zn film obtained by the Zn impurity doping at the second and third-stages. Based on excitation intensity dependence of photoluminescence (PL) at low-temperature, the change in the acceptor level was observed. The enhancement of carrier concentration as a result of Zn-doping in the p-type CIGS:Zn film was observed. The CIGS:Zn solar cells exhibited η of 14.5% and V{sub oc} of 0.658 V, which are higher than that of the corresponding solar cells using the undoped CIGS films. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Semi-transparent photovoltaic glazing based on electrodeposited CIGS solar cells on patterned molybdenum/glass substrates

Directory of Open Access Journals (Sweden)

Sidali Tarik

2018-01-01

Full Text Available In this paper, a new way of preparing semi-transparent solar cells using Cu(In1−xGaxSe2 (CIGS chalcopyrite semiconductors as absorbers for BIPV applications is presented. The key to the elaboration process consists in the co-electrodeposition of Cu-In-Ga mixed oxides on submillimetric hole-patterned molybdenum substrate, followed by thermal reduction to metallic alloys and selenisation. This method has the advantage of being a selective deposition technique where the thin film growth is carried out only on Mo covered areas. Thus, after annealing, the transparency of the sample is always preserved, allowing light to pass through the device. A complete device (5 × 5 cm2 with 535 μm diameter holes and total glass aperture of around 35% shows an open circuit voltage (VOC of 400 mV. Locally, the I-V curves reveal a maximum efficiency of 7.7%, VOC of 460 mV, JSC of 24 mA.cm−2 in an area of 0.1 cm2 with 35% aperture. This efficiency on the semi-transparent area is equivalent to a record efficiency of 11.9% by taking into account only the effective area.

The Effects of Annealing Parameters on the Crystallization and Morphology of Cu(In,GaSe2 Absorber Layers Prepared by Annealing Stacked Metallic Precursors

Directory of Open Access Journals (Sweden)

Chia-Ho Huang

2014-01-01

Full Text Available CIGS films are prepared by single-stage annealing of the solid Se-coated In/Cu-Ga bilayer precursor. The annealing processes were performed using various Ar pressures, heating rates, and soaking times. A higher Ar pressure is needed to fabricate highly crystalline CIGS films, as no extra Se-vapor source is supplied. As the heating rate increases, the surface morphologies of the CIGS films become looser and some cracks are observed. However, the influence of soaking time is insignificant and the selenization process only requires a short time when the precursors are selenized at a higher temperature with a lower heating rate and a higher Ar pressure. In this study, a dense chalcopyrite CIGS film with a thickness of about 1.5-1.6 μm, with large grains (~1.2 μm and no cracking or peeling is obtained after selenizing at a temperature of 550°C, an Ar pressure of 300 Torr, a heating rate of 60°C/min, and a soaking time of 20 min. By adequate design of the stacked precursor and controlling the annealing parameters, single-stage annealing of the solid Se-coated In/Cu-Ga bilayer precursor is simplified for the fabrication of a fully crystallized chalcopyrite CIGS absorber layers with good crystallization and large grains.

Point contacts at the copper-indium-gallium-selenide interface—A theoretical outlook

Energy Technology Data Exchange (ETDEWEB)

Bercegol, Adrien, E-mail: adrien.bercegol@polytechnique.edu; Chacko, Binoy; Klenk, Reiner; Lauermann, Iver; Lux-Steiner, Martha Ch. [Helmholtz-Zentrum Berlin für Materialien und Energie, Albert Einstein Straße 15, 12489 Berlin (Germany); Liero, Matthias [Weierstraß-Institut für Angewandte Analysis und Stochastik, 10117 Berlin (Germany)

2016-04-21

For a long time, it has been assumed that recombination in the space-charge region of copper-indium-gallium-selenide (CIGS) is dominant, at least in high efficiency solar cells with low band gap. The recent developments like potassium fluoride post deposition treatment and point-contact junction may call this into question. In this work, a theoretical outlook is made using three-dimensional simulations to investigate the effect of point-contact openings through a passivation layer on CIGS solar cell performance. A large set of solar cells is modeled under different scenarios for the charged defect levels and density, radius of the openings, interface quality, and conduction band offset. The positive surface charge created by the passivation layer induces band bending and this influences the contact (CdS) properties, making it beneficial for the open circuit voltage and efficiency, and the effect is even more pronounced when coverage area is more than 95%, and also makes a positive impact on the device performance, even in the presence of a spike at CIGS/CdS heterojunction.

Controlled formation of MoSe{sub 2} by MoN{sub x} thin film as a diffusion barrier against Se during selenization annealing for CIGS solar cell

Energy Technology Data Exchange (ETDEWEB)

Jeon, Chan-Wook [School of Chemical Engineering, Yeungnam University, Gyeongsangbuk-do 712-749 (Korea, Republic of); Cheon, Taehoon [School of Materials Science and Engineering, Yeungnam University, Gyeongsangbuk-do 712-749 (Korea, Republic of); Center for Core Research Facilities, DaeguGyeongbuk Institute of Science & Technology, Daegu (Korea, Republic of); Kim, Hangil [School of Materials Science and Engineering, Yeungnam University, Gyeongsangbuk-do 712-749 (Korea, Republic of); Kwon, Min-Su [School of Chemical Engineering, Yeungnam University, Gyeongsangbuk-do 712-749 (Korea, Republic of); Kim, Soo-Hyun [School of Materials Science and Engineering, Yeungnam University, Gyeongsangbuk-do 712-749 (Korea, Republic of)

2015-09-25

Highlights: • Mo/MoN{sub x}/Mo multilayer was investigated as a back contact for CIGS solar cell. • The MoN{sub x} protected the underlying Mo layer during high temperature selenization. • The formation of MoSe{sub 2} layer was precisely controlled. • The diffusion barrier performance of MoN{sub x} against Se was evaluated using TEM analysis. - Abstract: This study investigated the interfacial reactions and electrical properties of a Mo single layer and Mo/MoN{sub x}/Mo multilayer during high temperature selenization annealing. The Mo single layer was converted easily to MoSe{sub 2}, which was 7 times thicker than the Mo layer consumed ∼900 nm, by selenization at 460 °C for 10 min and the sheet resistance increased 8 fold compared to that of the as-deposited Mo film. On the other hand, in the Mo/MoN{sub x}/Mo structure, transmission electron microscopy (TEM) showed that the MoSe{sub 2} transformation was localized only in the top Mo layer and the bottom Mo layer was completely unaffected, even after selenization at 560 °C. The sheet resistance of the multilayer was relatively unchanged by selenization. This suggests that the MoN{sub x} layer performed well as a diffusion barrier against Se and the thickness of MoSe{sub 2} can be controlled precisely by adjusting the top Mo layer thickness. Furthermore, TEM and energy dispersive spectroscopy analysis showed that the selenized multilayer consisted of MoSe{sub 2}/Mo/MoN{sub x}/Mo, in which the top Mo layer of 60 nm was not fully converted to MoSe{sub 2} and 20 nm was left unreacted. The residual Mo interlayer located at the interface of MoSe{sub 2} and MoN{sub x} is believed to be beneficial for the ohmic contact of the selenized multilayer.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of next-generation thin-film solar cell module manufacturing technology - Development of CIS solar cell module manufacturing technology - Development of high-quality film enlargement technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu / kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project aims to establish a manufacturing process that enables both high-quality CuInSe{sub 2} (CIS) film solar cell enlargement and cost reduction and to develop a device structure which uses less heavy metal for the purposes of increasing the CIS thin-film solar cell size and efficiency and decreasing environmental impact. Several element technologies have been established for increasing the area of high-efficiency Cu(In, Ga)Se{sub 2} (CIGS) solar cells. Concerning the enlargement of the photoabsorption layer which is to assume the most important role, it is found that a high-quality CIGS film, which is near homogeneous though within a 10cm times 10cm area, is fabricated by an in-line vapor deposition method. As for dead area reduction and high-speed patterning, it is found that laser scribing works effectively in the patterning of the window layer and photoabsorption layer. As for reduction in the use of heavy metal, a high efficiency of 16.2% is attained in a cell not using a CdS film as expected in the case of a cell using a CdS film, this thanks to a CIGS film surface reforming technique. The technique of junction formation for CIGS solar cells is improved, and then a true efficiency of 18.5% is achieved. (NEDO)

Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (CuInSe2 based PV cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (CuInSe2 taiyo denchi seizo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on the fabrication technology of CuInSe2 based PV cell in fiscal 1994. (1) On formation of high-quality CIGS thin films by bilayer method, Mo film was deposited on a glass substrate by sputtering, and CIGS film with different Ga/In ratios was next formed on the substrate by quaternary simultaneous deposition at different In and Ga deposition speeds. In addition, CdS film was deposited on the CIGS film, and ZnO and ITO films were finally deposited on it by sputtering to complete solar cell. This solar cell offered the maximum conversion efficiency among cells using CIGS film. (2) On formation of high-quality CIGS thin films by three-stage method, a certain correlation was found between substrate temperature and CIGS film composition by monitoring substrate temperature in film forming process. This phenomenon allowed rigorous control of CIS film compositions important for CIS thin film solar cells. (3) On low-cost process technology for thin film formation, Cu(In,Ga)S2 solid solution film was fabricated by expanded selenic process. 3 figs.

Annealing enhancement effect by light illumination on proton irradiated Cu(In, Ga)Se2 thin-film solar cells

International Nuclear Information System (INIS)

Kawakita, Shirou; Imaizumi, Mitsuru; Matsuda, Sumio; Yamaguchi, Masafumi; Kushiya, Katsumi; Ohshima, Takeshi; Itoh, Hisayoshi

2002-01-01

In this paper, we investigated the high radiation tolerance of copper indium gallium di-selenide (CIGS) thin-film solar cells by conducting in situ measurements of short circuit current and open circuit voltage of CIGS thin-film solar cells during and after proton irradiation under short circuit condition. We found that the annealing rate of proton-induced defects in CIGS thin-film solar cells under light illumination with an AM0 solar simulator is higher than that under dark conditions. The activation energy of proton-induced defects in the CIGS thin-film solar cells with (without) light illumination is 0.80 eV (0.92 eV), which implies on enhanced defect annealing rate in CIGS thin-film solar cells due to minority-carrier injection. (author)

Influence of growth temperature of transparent conducting oxide layer on Cu(In,Ga)Se2 thin-film solar cells

International Nuclear Information System (INIS)

Cho, Dae-Hyung; Chung, Yong-Duck; Lee, Kyu-Seok; Park, Nae-Man; Kim, Kyung-Hyun; Choi, Hae-Won; Kim, Jeha

2012-01-01

We have studied the influence of growth temperature (T G ) in the deposition of an indium tin oxide (ITO) transparent conducting oxide layer on Cu(In,Ga)Se 2 (CIGS) thin-film solar cells. The ITO films were deposited on i-ZnO/glass and i-ZnO/CdS/CIGS/Mo/glass substrates using radio-frequency magnetron sputtering at various T G up to 350 °C. Both the resistivity of ITO and the interface quality of CdS/CIGS strongly depend on T G . For a T G ≤ 200 °C, a reduction in the series resistance enhanced the solar cell performance, while the p–n interface of the device was found to become deteriorated severely at T G > 200 °C. CIGS solar cells with ITO deposited at T G = 200 °C showed the best performance in terms of efficiency.

Assessing electronic cigarette emissions: linking physico-chemical properties to product brand, e-liquid flavoring additives, operational voltage and user puffing patterns.

Science.gov (United States)

Zhao, Jiayuan; Nelson, Jordan; Dada, Oluwabunmi; Pyrgiotakis, Georgios; Kavouras, Ilias G; Demokritou, Philip

2018-02-01

Users of electronic cigarettes (e-cigs) are exposed to particles and other gaseous pollutants. However, major knowledge gaps on the physico-chemical properties of such exposures and contradictory data in published literature prohibit health risk assessment. Here, the effects of product brand, type, e-liquid flavoring additives, operational voltage, and user puffing patterns on emissions were systematically assessed using a recently developed, versatile, e-cig exposure generation platform and state-of-the-art analytical methods. Parameters of interest in this systematic evaluation included two brands (A and B), three flavors (tobacco, menthol, and fruit), three types of e-cigs (disposable, pre-filled, and refillable tanks), two puffing protocols (4 and 2 s/puff), and four operational voltages (2.2-5.7 V). Particles were generated at a high number concentration (10 6 -10 7 particles/cm 3 ). The particle size distribution was bi-modal (∼200 nm and 1 µm). Furthermore, organic species (humectants propylene glycol and glycerin, nicotine) that were present in e-liquid and trace metals (potassium and sodium) that were present on e-cig heating coil were also released into the emission. In addition, combustion-related byproducts, such as benzene and toluene, were also detected in the range of 100-38,000 ppbv/puff. Parametric analyzes performed in this study show the importance of e-cig brand, type, flavor additives, user puffing pattern (duration and frequency), and voltage on physico-chemical properties of emissions. This observed influence is indicative of the complexity associated with the toxicological screening of emissions from e-cigs and needs to be taken into consideration.

Successful Nicotine Intake in Medical Assisted Use of E-Cigarettes: A Pilot Study.

Science.gov (United States)

Pacifici, Roberta; Pichini, Simona; Graziano, Silvia; Pellegrini, Manuela; Massaro, Giuseppina; Beatrice, Fabio

2015-07-08

The electronic cigarette (e-cig) has gained popularity as an aid in smoking cessation programs mainly because it maintains the gestures and rituals of tobacco smoking. However, it has been shown in inexperienced e-cig users that ineffective nicotine delivery can cause tobacco craving that could be responsible for unsuccessful smoking reduction/cessation. Moreover, the incorrect use of an e-cig could also led to potential nicotine overdosage and intoxication. Medically assisted training on the proper use of an e-cig plus behavioral support for tobacco dependence could be a pivotal step in avoiding both issues. We performed an eight-month pilot study of adult smokers who started e-cig use after receiving a multi-component medically assisted training program with monitoring of nicotine intake as a biomarker of correct e-cig use. Participants were tested during follow-up for breath carbon monoxide (CO), plasma cotinine and trans-3'-hydroxycotinine, and number of tobacco cigarettes smoked. At the end of the first, fourth, and eighth month of follow-up, 91.1, 73.5, and 76.5% of participants respectively were e-cig users ('only e-cig' and 'dual users'). They showed no significant variation in plasma cotinine and trans-3'-hydroxycotinine with respect to the start of the study when they smoked only tobacco cigarettes, but a significant reduction in breath CO. The proposed medically assisted training program of e-cig use led to a successful nicotine intake, lack of typical cigarette craving and overdosage symptoms and a significant decrease in the biomarker of cigarette combustion products.

[Smoking fewer cigarettes per day may determine a significant risk reduction in developing smoking attributable diseases? Is there a risk reduction for e-cigarette users?].

Science.gov (United States)

Pieri, Luca; Chellini, Elisabetta; Gorini, Giuseppe

2014-01-01

Among Italian smokers--about 10 millions in 2013--about 600,000 began using electronic cigarettes (e-cigs) in last years. About 10% of e-cig users quitted smoking tobacco, whereas the 90% was dual users. Among them, about three out of four decreased the number of cigarettes smoked per day (cig/day), but did not quit. How many fewer cigarettes a smoker has to smoke to obtain significant health benefits? Is there a threshold? In order to observe a significant 27% reduction in the risk of developing lung cancer, a smoker must reduce the number of cig/day by at least 50%, while for the other smoking-related diseases (acute myocardial infarction - AMI, stroke, chronic obstructive pulmonary diseases), halving the number of cig/day did not drive to a significant risk reduction. Even smoking 5 cig/day increases the risk of AMI, whereas it significantly lowers the risk of lung cancer. Obviously, quitting smoking is the best choice to highly reduce risks for all smoking-related diseases. Therefore, in order to achieve significant risk reductions, e-cig users should quit smoking as first choice, or, if they feel it is impossible to them, reduce the consumption of traditional cigarettes to less than 5 cig/day.

Reducing interface recombination for Cu(In,Ga)Se{sub 2} by atomic layer deposited buffer layers

Energy Technology Data Exchange (ETDEWEB)

Hultqvist, Adam; Bent, Stacey F. [Department of Chemical Engineering, Stanford University, Stanford, California 94305 (United States); Li, Jian V.; Kuciauskas, Darius; Dippo, Patricia; Contreras, Miguel A.; Levi, Dean H. [National Renewable Energy Laboratory, Golden, Colorado 80401 (United States)

2015-07-20

Partial CuInGaSe{sub 2} (CIGS) solar cell stacks with different atomic layer deposited buffer layers and pretreatments were analyzed by photoluminescence (PL) and capacitance voltage (CV) measurements to investigate the buffer layer/CIGS interface. Atomic layer deposited ZnS, ZnO, and SnO{sub x} buffer layers were compared with chemical bath deposited CdS buffer layers. Band bending, charge density, and interface state density were extracted from the CV measurement using an analysis technique new to CIGS. The surface recombination velocity calculated from the density of interface traps for a ZnS/CIGS stack shows a remarkably low value of 810 cm/s, approaching the range of single crystalline II–VI systems. Both the PL spectra and its lifetime depend on the buffer layer; thus, these measurements are not only sensitive to the absorber but also to the absorber/buffer layer system. Pretreatment of the CIGS prior to the buffer layer deposition plays a significant role on the electrical properties for the same buffer layer/CIGS stack, further illuminating the importance of good interface formation. Finally, ZnS is found to be the best performing buffer layer in this study, especially if the CIGS surface is pretreated with potassium cyanide.

Hydrogenated indium oxide window layers for high-efficiency Cu(In,Ga)Se{sub 2} solar cells

Energy Technology Data Exchange (ETDEWEB)

Jäger, Timo, E-mail: timo.jaeger@empa.ch; Romanyuk, Yaroslav E.; Nishiwaki, Shiro; Bissig, Benjamin; Pianezzi, Fabian; Fuchs, Peter; Gretener, Christina; Tiwari, Ayodhya N. [Empa – Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Thin Films and Photovoltaics, Überlandstrasse 129, 8600 Dübendorf (Switzerland); Döbeli, Max [ETH Zürich, Swiss Federal Institute of Technology, Laboratory of Ion Beam Physics, Otto-Stern-Weg 5, 8093 Zürich (Switzerland)

2015-05-28

High mobility hydrogenated indium oxide is investigated as a transparent contact for thin film Cu(In,Ga)Se{sub 2} (CIGS) solar cells. Hydrogen doping of In{sub 2}O{sub 3} thin films is achieved by injection of H{sub 2}O water vapor or H{sub 2} gas during the sputter process. As-deposited amorphous In{sub 2}O{sub 3}:H films exhibit a high electron mobility of ∼50 cm{sup 2}/Vs at room temperature. A bulk hydrogen concentration of ∼4 at. % was measured for both optimized H{sub 2}O and H{sub 2}-processed films, although the H{sub 2}O-derived film exhibits a doping gradient as detected by elastic recoil detection analysis. Amorphous IOH films are implemented as front contacts in CIGS based solar cells, and their performance is compared with the reference ZnO:Al electrodes. The most significant feature of IOH containing devices is an enhanced open circuit voltage (V{sub OC}) of ∼20 mV regardless of the doping approach, whereas the short circuit current and fill factor remain the same for the H{sub 2}O case or slightly decrease for H{sub 2}. The overall power conversion efficiency is improved from 15.7% to 16.2% by substituting ZnO:Al with IOH (H{sub 2}O) as front contacts. Finally, stability tests of non-encapsulated solar cells in dry air at 80 °C and constant illumination for 500 h demonstrate a higher stability for IOH-containing devices.

Impact of optical properties of front glass substrates on Cu(In,Ga)Se{sub 2} solar cells using lift-off process

Energy Technology Data Exchange (ETDEWEB)

Tamura, Akihiro, E-mail: ro005080@ed.ritsumei.ac.jp [College of Science and Engineering, Ritsumeikan University, Kusatsu, Shiga 525-0058 (Japan); Abe, Yasuhiro [Ritsumeikan Global Innovation Research Organization, Ritsumeikan University, Kusatsu, Shiga 525-0058 (Japan); Minemoto, Takashi [College of Science and Engineering, Ritsumeikan University, Kusatsu, Shiga 525-0058 (Japan)

2013-11-01

Transmittance of a front glass is one of the important factors in the development of high efficiency superstrate-type Cu(In,Ga)Se{sub 2} (CIGS) solar cells. In this study, we investigated the impact of optical properties of the front glass on the solar cell performance of the CIGS solar cells fabricated using the lift-off process. First, optical properties of quartz substrates and soda-lime glass (SLG) substrates with various thicknesses were investigated. Although optical properties of the SLG substrates depend on the thickness, those of the quartz substrates hardly depend on the thickness. Secondly, the superstrate-type CIGS solar cells were fabricated using 1-mm-thick SLG or 1-mm-thick quartz substrates. As a result, the short-circuit current density of the superstrate-type CIGS solar cell with 1-mm-thick quartz substrate was approximately 7% higher than that with 1-mm-thick SLG substrate, and its conversion efficiency was 7.1%. The external quantum efficiency of the solar cells was also improved using the quartz substrate as a front glass because transmittance and absorptance of the quartz substrate were superior to those of the SLG substrate. We therefore conclude that optical properties of the front glasses play an important role in the improvement of the superstrate-type solar cells. - Highlights: • Superstrate type Cu(In,Ga)Se{sub 2} solar cells are fabricated by lift-off process. • Various glasses are used as front glass for lift-off. • The impact of optical properties of the glasses on cell performance is investigated. • Quartz front glass gives 7% higher short-circuit current than soda-lime glass. • High transmittance is desired for front glass.

Fundamental Materials Research and Advanced Process Development for Thin-Film CIS-Based Photovoltaics: Final Technical Report, 2 October 2001 - 30 September 2005

Energy Technology Data Exchange (ETDEWEB)

Anderson, T. J.; Li, S. S.; Crisalle, O. D.; Craciun, V.

2006-09-01

The objectives for this thin-film copper-indium-diselenide (CIS) solar cell project cover the following areas: Develop and characterize buffer layers for CIS-based solar cell; grow and characterize chemical-bath deposition of Znx Cd1-xS buffer layers grown on CIGS absorbers; study effects of buffer-layer processing on CIGS thin films characterized by the dual-beam optical modulation technique; grow epitaxial CuInSe2 at high temperature; study the defect structure of CGS by photoluminescence spectroscopy; investigate deep-level defects in Cu(In,Ga)Se2 solar cells by deep-level transient spectroscopy; conduct thermodynamic modeling of the isothermal 500 C section of the Cu-In-Se system using a defect model; form alpha-CuInSe2 by rapid thermal processing of a stacked binary compound bilayer; investigate pulsed non-melt laser annealing on the film properties and performance of Cu(In,Ga)Se2 solar cells; and conduct device modeling and simulation of CIGS solar cells.

High performance homes

DEFF Research Database (Denmark)

Beim, Anne; Vibæk, Kasper Sánchez

2014-01-01

Can prefabrication contribute to the development of high performance homes? To answer this question, this chapter defines high performance in more broadly inclusive terms, acknowledging the technical, architectural, social and economic conditions under which energy consumption and production occur....... Consideration of all these factors is a precondition for a truly integrated practice and as this chapter demonstrates, innovative project delivery methods founded on the manufacturing of prefabricated buildings contribute to the production of high performance homes that are cost effective to construct, energy...

E-Area Performance Assessment Interim Measures Assessment FY2005

Energy Technology Data Exchange (ETDEWEB)

Stallings, M

2006-01-31

After major changes to the limits for various disposal units of the E-Area Low Level Waste Facility (ELLWF) last year, no major changes have been made during FY2005. A Special Analysis was completed which removes the air pathway {sup 14}C limit from the Intermediate Level Vault (ILV). This analysis will allow the disposal of reactor moderator deionizers which previously had no pathway to disposal. Several studies have also been completed providing groundwater transport input for future special analyses. During the past year, since Slit Trenches No.1 and No.2 were nearing volumetric capacity, they were operationally closed under a preliminary closure analysis. This analysis was performed using as-disposed conditions and data and showed that concrete rubble from the demolition of 232-F was acceptable for disposal in the STs even though the latest special analysis for the STs had reduced the tritium limits so that the inventory in the rubble exceeded limits. A number of special studies are planned during the next years; perhaps the largest of these will be revision of the Performance Assessment (PA) for the ELLWF. The revision will be accomplished by incorporating special analyses performed since the last PA revision as well as revising analyses to include new data. Projected impacts on disposal limits of more recent studies have been estimated. No interim measures will be applied during this year. However, it is being recommended that tritium disposals to the Components-in-Grout (CIG) Trenches be suspended until a limited Special Analysis (SA) currently in progress is completed. This SA will give recommendations for optimum placement of tritiated D-Area tower waste. Further recommendations for tritiated waste placement in the CIG Trenches will be given in the upcoming PA revision.

Temperature Effect on Power Drop of Different Photovoltaic Modules

Directory of Open Access Journals (Sweden)

Emad Talib Hahsim

2016-05-01

Full Text Available Solar module operating temperature is the second major factor affects the performance of solar photovoltaic panels after the amount of solar radiation. This paper presents a performance comparison of mono-crystalline Silicon (mc-Si, poly-crystalline Silicon (pc-Si, amorphous Silicon (a-Si and Cupper Indium Gallium di-selenide (CIGS photovoltaic technologies under Climate Conditions of Baghdad city. Temperature influence on the solar modules electric output parameters was investigated experimentally and their temperature coefficients was calculated. These temperature coefficients are important for all systems design and sizing. The experimental results revealed that the pc-Si module showed a decrease in open circuit voltage by -0.0912V/ºC while mc-Si and a-Si had nearly -0.07V/ºC and the CIGS has -0.0123V/ºC. The results showed a slightly increase in short circuit current with temperature increasing about 0.3mA/ºC ,4.4mA/ºC and 0.9mA/ºC for mc-Si , pc-Si and both a-Si and CIGS. The mc-Si had the largest drop in output power about -0.1353W/ºC while -0.0915, -0.0114 and -0.0276 W/ºC for pc-Si, a-Si and CIGS respectively. The amorphous silicon is the more suitable module for high operation temperature but it has the lowest conversion efficiency between the tested modules.

CuIn{sub 1-x}Ga{sub x}Se{sub 2} photovoltaic devices for tandem solar cell application

Energy Technology Data Exchange (ETDEWEB)

Seyrling, S. [Thin Film Physics Group, Laboratory for Solid-State Physics, ETH Zuerich, Technopark, Technoparkstrasse 1, 8005 Zuerich (Switzerland)], E-mail: seyrling@phys.ethz.ch; Calnan, S. [Department of Electronic and Electrical Engineering, Loughborough University, Leicestershire, LE11 3TU (United Kingdom); Buecheler, S. [Thin Film Physics Group, Laboratory for Solid-State Physics, ETH Zuerich, Technopark, Technoparkstrasse 1, 8005 Zuerich (Switzerland); Huepkes, J. [Institut fuer Energieforschung, Photovoltaik, Forschungszentrum Juelich GmbH, 52425 Juelich (Germany); Wenger, S. [Laboratory of Photonics and Interfaces, Institute of Chemical Sciences and Engineering, School of Basic Sciences, EPF Lausanne, 1015 Lausanne (Switzerland); Bremaud, D.; Zogg, H. [Thin Film Physics Group, Laboratory for Solid-State Physics, ETH Zuerich, Technopark, Technoparkstrasse 1, 8005 Zuerich (Switzerland); Tiwari, A.N. [Thin Film Physics Group, Laboratory for Solid-State Physics, ETH Zuerich, Technopark, Technoparkstrasse 1, 8005 Zuerich (Switzerland); Department of Electronic and Electrical Engineering, Loughborough University, Leicestershire, LE11 3TU (United Kingdom)

2009-02-02

CuIn{sub 1-x}Ga{sub x}Se{sub 2} (CIGS) solar cells show a good spectral response in a wide range of the solar spectrum and the bandgap of CIGS can be adjusted from 1.0 eV to 1.7 eV by increasing the gallium-to-indium ratio of the absorber. While the bandgaps of Ga-rich CIGS or CGS devices make them suitable for top or intermediate cells, the In rich CIGS or CIS devices are well suited to be used as bottom cells in tandem solar cells. The photocurrent can be adapted to the desired value for current matching in tandem cells by changing the composition of CIGS which influences the absorption characteristics. Therefore, CIGS layers with different [Ga]/[In + Ga] ratios were grown on Mo and ZnO:Al coated glass substrates. The grain size, composition of the layers, and morphology strongly depend on the Ga content. Layers with Ga rich composition exhibit smaller grain size and poor photovoltaic performance. The current densities of CIGS solar cells on ZnO:Al/glass varied from 29 mA cm{sup -2} to 13 mA cm{sup -2} depending on the Ga content, and 13.5% efficient cells were achieved using a low temperature process (450 deg. C ). However, Ga-rich solar cells exhibit lower transmission than dye sensitized solar cells (DSC). Prospects of tandem solar cells combining a DSC with CIGS are presented.

Toward automated e-cigarette surveillance: Spotting e-cigarette proponents on Twitter.

Science.gov (United States)

Kavuluru, Ramakanth; Sabbir, A K M

2016-06-01

Electronic cigarettes (e-cigarettes or e-cigs) are a popular emerging tobacco product. Because e-cigs do not generate toxic tobacco combustion products that result from smoking regular cigarettes, they are sometimes perceived and promoted as a less harmful alternative to smoking and also as means to quit smoking. However, the safety of e-cigs and their efficacy in supporting smoking cessation is yet to be determined. Importantly, the federal drug administration (FDA) currently does not regulate e-cigs and as such their manufacturing, marketing, and sale is not subject to the rules that apply to traditional cigarettes. A number of manufacturers, advocates, and e-cig users are actively promoting e-cigs on Twitter. We develop a high accuracy supervised predictive model to automatically identify e-cig "proponents" on Twitter and analyze the quantitative variation of their tweeting behavior along popular themes when compared with other Twitter users (or tweeters). Using a dataset of 1000 independently annotated Twitter profiles by two different annotators, we employed a variety of textual features from latest tweet content and tweeter profile biography to build predictive models to automatically identify proponent tweeters. We used a set of manually curated key phrases to analyze e-cig proponent tweets from a corpus of over one million e-cig tweets along well known e-cig themes and compared the results with those generated by regular tweeters. Our model identifies e-cig proponents with 97% precision, 86% recall, 91% F-score, and 96% overall accuracy, with tight 95% confidence intervals. We find that as opposed to regular tweeters that form over 90% of the dataset, e-cig proponents are a much smaller subset but tweet two to five times more than regular tweeters. Proponents also disproportionately (one to two orders of magnitude more) highlight e-cig flavors, their smoke-free and potential harm reduction aspects, and their claimed use in smoking cessation. Given FDA is

EffiCiency and Safety of an eLectronic cigAreTte (ECLAT as tobacco cigarettes substitute: a prospective 12-month randomized control design study.

Directory of Open Access Journals (Sweden)

Pasquale Caponnetto

Full Text Available Electronic cigarettes (e-cigarettes are becoming increasingly popular with smokers worldwide. Users report buying them to help quit smoking, to reduce cigarette consumption, to relieve tobacco withdrawal symptoms, and to continue having a 'smoking' experience, but with reduced health risks. Research on e-cigarettes is urgently needed in order to ensure that the decisions of regulators, healthcare providers and consumers are based on science. Methods ECLAT is a prospective 12-month randomized, controlled trial that evaluates smoking reduction/abstinence in 300 smokers not intending to quit experimenting two different nicotine strengths of a popular e-cigarette model ('Categoria'; Arbi Group Srl, Italy compared to its non-nicotine choice. GroupA (n = 100 received 7.2 mg nicotine cartridges for 12 weeks; GroupB (n = 100, a 6-week 7.2 mg nicotine cartridges followed by a further 6-week 5.4 mg nicotine cartridges; GroupC (n = 100 received no-nicotine cartridges for 12 weeks. The study consisted of nine visits during which cig/day use and exhaled carbon monoxide (eCO levels were measured. Smoking reduction and abstinence rates were calculated. Adverse events and product preferences were also reviewed.Declines in cig/day use and eCO levels were observed at each study visits in all three study groups (p<0.001 vs baseline, with no consistent differences among study groups. Smoking reduction was documented in 22.3% and 10.3% at week-12 and week-52 respectively. Complete abstinence from tobacco smoking was documented in 10.7% and 8.7% at week-12 and week-52 respectively. A substantial decrease in adverse events from baseline was observed and withdrawal symptoms were infrequently reported during the study. Participants' perception and acceptance of the product under investigation was satisfactory.In smokers not intending to quit, the use of e-cigarettes, with or without nicotine, decreased cigarette consumption and elicited enduring tobacco

Physics of grain boundaries in polycrystalline photovoltaic semiconductors

Energy Technology Data Exchange (ETDEWEB)

Yan, Yanfa, E-mail: yanfa.yan@utoledo.edu; Yin, Wan-Jian; Wu, Yelong; Shi, Tingting; Paudel, Naba R. [Department of Physics and Astronomy and Wright Center for Photovoltaics Innovation and Commercialization, The University of Toledo, Ohio 43606 (United States); Li, Chen [Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Poplawsky, Jonathan [The Center for Nanophase Materials Sciences, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Wang, Zhiwei [Department of Physics and Astronomy and Wright Center for Photovoltaics Innovation and Commercialization, The University of Toledo, Ohio 43606 (United States); National Renewable Energy Laboratory, Golden, Colorado 80401 (United States); Moseley, John; Guthrey, Harvey; Moutinho, Helio; Al-Jassim, Mowafak M. [National Renewable Energy Laboratory, Golden, Colorado 80401 (United States); Pennycook, Stephen J. [Department of Materials Science and Engineering, University of Tennessee, Knoxville, Tennessee 37996 (United States)

2015-03-21

Thin-film solar cells based on polycrystalline Cu(In,Ga)Se{sub 2} (CIGS) and CdTe photovoltaic semiconductors have reached remarkable laboratory efficiencies. It is surprising that these thin-film polycrystalline solar cells can reach such high efficiencies despite containing a high density of grain boundaries (GBs), which would seem likely to be nonradiative recombination centers for photo-generated carriers. In this paper, we review our atomistic theoretical understanding of the physics of grain boundaries in CIGS and CdTe absorbers. We show that intrinsic GBs with dislocation cores exhibit deep gap states in both CIGS and CdTe. However, in each solar cell device, the GBs can be chemically modified to improve their photovoltaic properties. In CIGS cells, GBs are found to be Cu-rich and contain O impurities. Density-functional theory calculations reveal that such chemical changes within GBs can remove most of the unwanted gap states. In CdTe cells, GBs are found to contain a high concentration of Cl atoms. Cl atoms donate electrons, creating n-type GBs between p-type CdTe grains, forming local p-n-p junctions along GBs. This leads to enhanced current collections. Therefore, chemical modification of GBs allows for high efficiency polycrystalline CIGS and CdTe thin-film solar cells.

Photoluminescence study of high energy proton irradiation on Cu(In,Ga)Se{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Koo, Bonhyeong [Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon 305-701 (Korea, Republic of); Lee, June Hyuk [Neutron Science Division, Korea Atomic Energy Research Institute (KAERI), 989-111 Daedeok-daero, Yuseong-gu, Daejeon 305-353 (Korea, Republic of); Shin, Donghyeop [Department of Mechanical Engineering and Materials Science, Duke University, Durham, NC 27708 (United States); Ahn, Byung Tae, E-mail: btahn@kaist.ac.kr [Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon 305-701 (Korea, Republic of); Shin, Byungha, E-mail: byungha@kaist.ac.kr [Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon 305-701 (Korea, Republic of)

2016-03-31

We have studied the effect of proton irradiation on Cu(In,Ga)Se{sub 2} (CIGS) thin films using photoluminescence (PL). We used a 10 MeV proton beam with varying doses from 10{sup 9} to 10{sup 12} cm{sup −2}. Intensity-dependent low temperature PL measurements suggest that the proton irradiation does not create a new defect level but instead changes the number of preexisting defects in the detection range of the PL system. By comparing PL spectra after the proton irradiation with those obtained after thermal annealing under inert gas as well as under hydrogen gas ambient, we find that the irradiation-induced change in the defect structure does not originate from the incorporation of hydrogen but from energetics of the irradiating particles. Electrical resistivity of the proton irradiated CIGS thin films is shown to decrease after the proton irradiation, and this is explained by the reduction of the concentration of compensating donor-like defects, specifically selenium vacancies, based on the PL results. - Highlights: • Photoluminescence study of 10 MeV proton irradiation on CIGS at 10 K. • Irradiation modified population of existing defects without introducing new levels. • Changes in CIGS by 10 MeV irradiation are due to energetics of irradiating protons.

Individual identification of free hole and electron dynamics in CuIn{sub 1−x}Ga{sub x}Se{sub 2} thin films by simultaneous monitoring of two optical transitions

Energy Technology Data Exchange (ETDEWEB)

Okano, Makoto [Institute for Chemical Research, Kyoto University, Uji, Kyoto 611-0011 (Japan); Hagiya, Hideki; Sakurai, Takeaki; Akimoto, Katsuhiro [Institute of Applied Physics, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); Shibata, Hajime; Niki, Shigeru [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Ibaraki 305-8568 (Japan); Kanemitsu, Yoshihiko, E-mail: kanemitu@scl.kyoto-u.ac.jp [Institute for Chemical Research, Kyoto University, Uji, Kyoto 611-0011 (Japan); Japan Science and Technology Agency, CREST, Kyoto University, Uji, Kyoto 611-0011 (Japan)

2015-05-04

The photocarrier dynamics of CuIn{sub 1−x}Ga{sub x}Se{sub 2} (CIGS) thin films were studied using white-light transient absorption (TA) measurements, as an understanding of this behavior is essential for improving the performance of solar cells composed of CIGS thin films. A characteristic double-peak structure due to the splitting of the valence bands in the CIGS was observed in the TA spectra under near-band-gap resonant excitation. From a comparison of the TA decay dynamics monitored at these two peaks, it was found that the slow-decay components of the electron and hole relaxation are on the nanosecond timescale. This finding is clear evidence of the long lifetimes of free photocarriers in polycrystalline CIGS thin films.

Low-cost ZnO:Al transparent contact by reactive rotatable magnetron sputtering for Cu(In,Ga)Se2 solar modules

International Nuclear Information System (INIS)

Menner, R.; Hariskos, D.; Linss, V.; Powalla, M.

2011-01-01

Sputtering ZnO as transparent front contact (TCO) is standard in today's industrial scale Cu(In,Ga)Se 2 (CIGS) module manufacturing. Although innovative concepts like rotatable magnetron sputtering from ceramic targets have been realised, costs are still high due to expensive ceramic targets. Significant cost reductions are expected by using reactive sputtering of metallic targets. Therefore, ZSW and industrial partners investigated the reactive sputtering of Al-doped zinc oxide (ZAO) as TCO on CIGS absorbers of high quality and industrial relevance. The reactive DC sputtering from rotatable magnetron targets is controlled in the transition mode by adjusting oxygen flow and discharge voltage. Optimisation leads to ZAO films with a TCO quality nearly comparable to standard films deposited by DC ceramic sputtering. Scanning electron microscopy, X-ray diffraction, and Hall analyses of the ZAO films are performed. Medium-size CIGS modules are coated with reactively sputtered ZAO, resulting in 12.8% module efficiency and surpassing the efficiency of the ceramic witness device. Cd-free buffered devices are also successfully coated with reactive TCO. Damp heat stability according to IEC61646 is met by all reactively sputtered devices.

The development of hydrazine-processed Cu(In,Ga)(Se,S){sub 2} solar cells

Energy Technology Data Exchange (ETDEWEB)

Bob, Brion; Lei, Bao; Chung, Choong-Heui; Yang, Wenbing; Hsu, Wan-Ching; Duan, Hsin-Sheng; Hou, William Wei-Jen; Li, Sheng-Han; Yang, Yang [Department of Materials Science and Engineering, University of California, Los Angeles, CA (United States)

2012-05-15

The hydrazine-based deposition of Cu(In,Ga)(S,Se){sub 2} (CIGS) thin films has attracted considerable attention in recent years due to its potential for the high-throughput production of photovoltaic devices based on this absorber material. This article provides an introduction as well as presenting a complete picture of the current status of hydrazine-based CIGS solar-cell fabrication, including the three major steps of this deposition process: dissolution of the precursor materials in hydrazine, deposition of a film from the resulting precursor solution, and the completion and characterization of a photovoltaic device following absorber deposition. Recent discoveries are then discussed, regarding the dissolution chemistry of the relevant precursor complexes in hydrazine, which together represent the true foundation of this processing method. Recent studies on CIGS film formation are then summarized, including the control and analysis of the crystalline phase, electronic bandgap, and film morphology. Finally, the latest progress in high-performance device fabrication is highlighted, with a focus on optoelectronic characterization including current-voltage, junction capacitance, and minority carrier lifetime measurements. Finally, a discussion and future outlook is provided. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Barrier effect of AlN film in flexible Cu(In,Ga)Se{sub 2} solar cells on stainless steel foil and solar cell

Energy Technology Data Exchange (ETDEWEB)

Li, Boyan; Li, Jianjun [Institute of Photo-electronic Thin Film Devices and Technology, Key Laboratory of Photo-electronic Thin Film Devices and Technology of Tianjin, Nankai University, Tianjin 300071 (China); Wu, Li [The MOE Key Laboratory of Weak-Light Nonlinear Photonics, School of Physics, Nankai University, Tianjin 300071 (China); Liu, Wei; Sun, Yun [Institute of Photo-electronic Thin Film Devices and Technology, Key Laboratory of Photo-electronic Thin Film Devices and Technology of Tianjin, Nankai University, Tianjin 300071 (China); Zhang, Yi, E-mail: yizhang@nankai.edu.cn [Institute of Photo-electronic Thin Film Devices and Technology, Key Laboratory of Photo-electronic Thin Film Devices and Technology of Tianjin, Nankai University, Tianjin 300071 (China)

2015-04-05

Highlights: • The adhension between AlN film and Mo are verygood. • AlN film can be effectively used as the barrier of flexible CIGS solar cell on SS substrate. • AlN film is suitable as the insulation barrier of flexible CIGS solar cell on SS substrate. - Abstract: The AlN film deposited by DC magnetron sputtering on stainless steel (SS) foils was used as the barrier in flexible Cu(In,Ga)Se{sub 2} (CIGS) solar cells on stainless steel foil and characterized comprehensively by X-ray diffraction (XRD), scanning electron microscopy (SEM), I–V, and QE measurements study. The study of AlN as insulation barrier in the flexible CIGS solar cell showed that the adhesion strength between the SS foil and the deposited AlN film was very strong even after annealing at high temperature at 530 °C. More importantly, a high resistance of over 10 MΩ was remained with the film with thickness of around 200 nm after annealing. This indicates that the AlN film is suitable as an effective insulation barrier in flexible CIGS solar cells based on SS foil. In addition, the XRD and SEM results showed that the AlN film did not influence the crystal structure of the Mo film which was deposited upon the AlN layer and used as the electrical contact in CIGS solar cells. It was found that the AlN film contributed to an improved crystallinity of the Mo contact layer compared to the bare SS foil. The combined results of secondary ion mass spectrometry, I–V and EQE measurements of the corresponding flexible CIGS solar cells confirmed that 1 μm-thick AlN film could be used as an efficient barrier layer in CIGS solar cells on SS foil.

Employing Si solar cell technology to increase efficiency of ultra-thin Cu(In,Ga)Se2 solar cells.

Science.gov (United States)

Vermang, Bart; Wätjen, Jörn Timo; Fjällström, Viktor; Rostvall, Fredrik; Edoff, Marika; Kotipalli, Ratan; Henry, Frederic; Flandre, Denis

2014-10-01

Reducing absorber layer thickness below 500 nm in regular Cu(In,Ga)Se 2 (CIGS) solar cells decreases cell efficiency considerably, as both short-circuit current and open-circuit voltage are reduced because of incomplete absorption and high Mo/CIGS rear interface recombination. In this work, an innovative rear cell design is developed to avoid both effects: a highly reflective rear surface passivation layer with nano-sized local point contact openings is employed to enhance rear internal reflection and decrease the rear surface recombination velocity significantly, as compared with a standard Mo/CIGS rear interface. The formation of nano-sphere shaped precipitates in chemical bath deposition of CdS is used to generate nano-sized point contact openings. Evaporation of MgF 2 coated with a thin atomic layer deposited Al 2 O 3 layer, or direct current magnetron sputtering of Al 2 O 3 are used as rear surface passivation layers. Rear internal reflection is enhanced substantially by the increased thickness of the passivation layer, and also the rear surface recombination velocity is reduced at the Al 2 O 3 /CIGS rear interface. (MgF 2 /)Al 2 O 3 rear surface passivated ultra-thin CIGS solar cells are fabricated, showing an increase in short circuit current and open circuit voltage compared to unpassivated reference cells with equivalent CIGS thickness. Accordingly, average solar cell efficiencies of 13.5% are realized for 385 nm thick CIGS absorber layers, compared with 9.1% efficiency for the corresponding unpassivated reference cells.

Employing Si solar cell technology to increase efficiency of ultra-thin Cu(In,Ga)Se2 solar cells

Science.gov (United States)

Vermang, Bart; Wätjen, Jörn Timo; Fjällström, Viktor; Rostvall, Fredrik; Edoff, Marika; Kotipalli, Ratan; Henry, Frederic; Flandre, Denis

2014-01-01

Reducing absorber layer thickness below 500 nm in regular Cu(In,Ga)Se2 (CIGS) solar cells decreases cell efficiency considerably, as both short-circuit current and open-circuit voltage are reduced because of incomplete absorption and high Mo/CIGS rear interface recombination. In this work, an innovative rear cell design is developed to avoid both effects: a highly reflective rear surface passivation layer with nano-sized local point contact openings is employed to enhance rear internal reflection and decrease the rear surface recombination velocity significantly, as compared with a standard Mo/CIGS rear interface. The formation of nano-sphere shaped precipitates in chemical bath deposition of CdS is used to generate nano-sized point contact openings. Evaporation of MgF2 coated with a thin atomic layer deposited Al2O3 layer, or direct current magnetron sputtering of Al2O3 are used as rear surface passivation layers. Rear internal reflection is enhanced substantially by the increased thickness of the passivation layer, and also the rear surface recombination velocity is reduced at the Al2O3/CIGS rear interface. (MgF2/)Al2O3 rear surface passivated ultra-thin CIGS solar cells are fabricated, showing an increase in short circuit current and open circuit voltage compared to unpassivated reference cells with equivalent CIGS thickness. Accordingly, average solar cell efficiencies of 13.5% are realized for 385 nm thick CIGS absorber layers, compared with 9.1% efficiency for the corresponding unpassivated reference cells. PMID:26300619

Effects of the environment on galaxies in the Catalogue of Isolated Galaxies: physical satellites and large scale structure

Science.gov (United States)

Argudo-Fernández, M.; Verley, S.; Bergond, G.; Sulentic, J.; Sabater, J.; Fernández Lorenzo, M.; Espada, D.; Leon, S.; Sánchez-Expósito, S.; Santander-Vela, J. D.; Verdes-Montenegro, L.

2014-04-01

Context. We present a study of the 3D environment for a sample of 386 galaxies in the Catalogue of Isolated Galaxies (CIG, Karachentseva 1973) using the Ninth Data Release of the Sloan Digital Sky Survey (SDSS-DR9). Aims: We aim to identify and quantify the effects of the satellite distribution around a sample of galaxies in the CIG, as well as the effects of the large-scale structure (LSS). Methods: To recover the physically bound galaxies we first focused on the satellites that are within the escape speed of each CIG galaxy. We also propose a more conservative method using the stacked Gaussian distribution of the velocity difference of the neighbours. The tidal strengths affecting the primary galaxy were estimated to quantify the effects of the local and LSS environments. We also defined the projected number density parameter at the fifth nearest neighbour to characterise the LSS around the CIG galaxies. Results: Out of the 386 CIG galaxies considered in this study, at least 340 (88% of the sample) have no physically linked satellite. Following the more conservative Gaussian distribution of physical satellites around the CIG galaxies leads to upper limits. Out of the 386 CIG galaxies, 327 (85% of the sample) have no physical companion within a projected distance of 0.3 Mpc. The CIG galaxies are distributed following the LSS of the local Universe, although presenting a large heterogeneity in their degree of connection with it. When present around a CIG galaxy, the effect of physically bound galaxies largely dominates (typically by more than 90%) the tidal strengths generated by the LSS. Conclusions: The CIG samples a variety of environments, from galaxies with physical satellites to galaxies without neighbours within 3 Mpc. A clear segregation appears between early-type CIG galaxies with companions and isolated late-type CIG galaxies. Isolated galaxies are in general bluer, with probably younger stellar populations and very high star formation compared with older

Primeros datos sobre movimientos de cigüeñas blancas Ciconia ciconia L., 1758 anilladas como pollos en nido en Navarra: 2012-2015.

Directory of Open Access Journals (Sweden)

Jaime Resano-Mayor, Juan M. Barbarín, Daniel Alonso, Blanca Fernández-Eslava, Diego Villanua, Jesús Mari Lekuona, Ricardo Rodríguez,

2016-01-01

(i.e., avistamientos como muertos (i.e., recuperaciones, en su mayoría por electrocución. Todos los avistamientos, excepto tres, se realizaron en vertederos (n = 64, en donde el esfuerzo de muestreo fue considerablemente mayor. Dos avistamientos correspondieron a cigüeñas observadas en humedales, así como otro ejemplar que se observó dos años después en la colonia donde nació (i.e., reclutamiento. La distancia promedio de avistamiento en relación a la colonia de anillamiento fue de 48 km (distancia máxima, 410 km. La mayoría de avistamientos/recuperaciones se realizó durante la primavera y verano, con independencia de la edad. Todas las aves que se hallaron muertas (n = 7 fueron jóvenes encontrados en la proximidad de sus colonias de nacimiento.

Analysis of performance and device parameters of CIGS PV modules deployed outdoors

International Nuclear Information System (INIS)

Radue, C.; Dyk, E.E. van; Macabebe, E.Q.

2009-01-01

Two 20 W copper indium gallium diselenide photovoltaic modules were subjected to a thorough indoor assessment procedure, followed by outdoor deployment at the Nelson Mandela Metropolitan University as part of an ongoing study. The initial indoor measurement of maximum power output (P MAX ) of one of the modules was considerably higher than the manufacturer's rating (E.E. van Dyk, C. Radue and A.R. Gxasheka, Thin Solid Films 515 (2007) 6196). The modules were deployed on a dual-axis solar tracker and current-voltage characteristics were obtained weekly. In addition to the normal PV parameters of short-circuit current, open-circuit voltage, P MAX , fill factor and efficiency, shunt and series resistances were also monitored. The performances of the two modules are compared and analyzed and the results presented in this paper

Supply risks associated with CdTe and CIGS thin-film photovoltaics

International Nuclear Information System (INIS)

Helbig, Christoph; Bradshaw, Alex M.; Kolotzek, Christoph; Thorenz, Andrea; Tuma, Axel

2016-01-01

Highlights: • Supply risks associated with thin film photovoltaic technologies are considered. • Eleven supply risk indicators are used to evaluate Cd, Te, Cu, In, Ga, Se and Mo. • Indicator weighting based on peer assessment and an Analytic Hierarchy Process. • Various possibilities for the aggregation of elemental supply risks discussed. • Aggregated results show a marginally lower supply risk for CdTe than for CIGS. - Abstract: As a result of the global warming potential of fossil fuels there has been a rapid growth in the installation of photovoltaic generating capacity in the last decade. While this market is dominated by crystalline silicon, thin-film photovoltaics are still expected to make a substantial contribution to global electricity supply in future, due both to lower production costs and to recent increases in conversion efficiency. At present, cadmium telluride (CdTe) and copper-indium-gallium diselenide (CuIn_xGa_1_−_xSe_2) seem to be the most promising materials and currently have a share of ≈9% of the photovoltaic market. An expected stronger market penetration by these thin-film technologies raises the question as to the supply risks associated with the constituent elements. Against this background, we report here a semi-quantitative, relative assessment of mid- to long-term supply risk associated with the elements Cd, Te, Cu, In, Ga, Se and Mo. In this approach, the supply risk is measured using 11 indicators in the four categories “Risk of Supply Reduction”, “Risk of Demand Increase”, “Concentration Risk” and “Political Risk”. In a second step, the single indicator values, which are derived from publicly accessible databases, are weighted relative to each other specifically for the case of thin film photovoltaics. For this purpose, a survey among colleagues and an Analytic Hierarchy Process (AHP) approach are used, in order to obtain a relative, element-specific value for the supply risk. The aggregation of these

Analysis of performance and device parameters of CIGS PV modules deployed outdoors

Energy Technology Data Exchange (ETDEWEB)

Radue, C. [Physics Department, P.O. Box 77000, Nelson Mandela Metropolitan University, Port Elizabeth, 6031 (South Africa)], E-mail: chantelle.radue@nmmu.ac.za; Dyk, E.E. van; Macabebe, E.Q. [Physics Department, P.O. Box 77000, Nelson Mandela Metropolitan University, Port Elizabeth, 6031 (South Africa)

2009-02-02

Two 20 W copper indium gallium diselenide photovoltaic modules were subjected to a thorough indoor assessment procedure, followed by outdoor deployment at the Nelson Mandela Metropolitan University as part of an ongoing study. The initial indoor measurement of maximum power output (P{sub MAX}) of one of the modules was considerably higher than the manufacturer's rating (E.E. van Dyk, C. Radue and A.R. Gxasheka, Thin Solid Films 515 (2007) 6196). The modules were deployed on a dual-axis solar tracker and current-voltage characteristics were obtained weekly. In addition to the normal PV parameters of short-circuit current, open-circuit voltage, P{sub MAX}, fill factor and efficiency, shunt and series resistances were also monitored. The performances of the two modules are compared and analyzed and the results presented in this paper.

High Performance Marine Vessels

CERN Document Server

Yun, Liang

2012-01-01

High Performance Marine Vessels (HPMVs) range from the Fast Ferries to the latest high speed Navy Craft, including competition power boats and hydroplanes, hydrofoils, hovercraft, catamarans and other multi-hull craft. High Performance Marine Vessels covers the main concepts of HPMVs and discusses historical background, design features, services that have been successful and not so successful, and some sample data of the range of HPMVs to date. Included is a comparison of all HPMVs craft and the differences between them and descriptions of performance (hydrodynamics and aerodynamics). Readers will find a comprehensive overview of the design, development and building of HPMVs. In summary, this book: Focuses on technology at the aero-marine interface Covers the full range of high performance marine vessel concepts Explains the historical development of various HPMVs Discusses ferries, racing and pleasure craft, as well as utility and military missions High Performance Marine Vessels is an ideal book for student...

Comparative In Vitro Toxicity Profile of Electronic and Tobacco Cigarettes, Smokeless Tobacco and Nicotine Replacement Therapy Products: E-Liquids, Extracts and Collected Aerosols

Directory of Open Access Journals (Sweden)

Manoj Misra

2014-10-01

Full Text Available The use of electronic cigarettes (e-cigs continues to increase worldwide in parallel with accumulating information on their potential toxicity and safety. In this study, an in vitro battery of established assays was used to examine the cytotoxicity, mutagenicity, genotoxicity and inflammatory responses of certain commercial e-cigs and compared to tobacco burning cigarettes, smokeless tobacco (SLT products and a nicotine replacement therapy (NRT product. The toxicity evaluation was performed on e-liquids and pad-collected aerosols of e-cigs, pad-collected smoke condensates of tobacco cigarettes and extracts of SLT and NRT products. In all assays, exposures with e-cig liquids and collected aerosols, at the doses tested, showed no significant activity when compared to tobacco burning cigarettes. Results for the e-cigs, with and without nicotine in two evaluated flavor variants, were very similar in all assays, indicating that the presence of nicotine and flavors, at the levels tested, did not induce any cytotoxic, genotoxic or inflammatory effects. The present findings indicate that neither the e-cig liquids and collected aerosols, nor the extracts of the SLT and NRT products produce any meaningful toxic effects in four widely-applied in vitro test systems, in which the conventional cigarette smoke preparations, at comparable exposures, are markedly cytotoxic and genotoxic.

Differences between Dual Users and Switchers Center around Vaping Behavior and Its Experiences Rather than Beliefs and Attitudes.

Science.gov (United States)

Adriaens, Karolien; Van Gucht, Dinska; Baeyens, Frank

2017-12-23

(1) Background: Many smokers completely switch to vaping (switchers), whereas others use e-cigarettes (e-cigs) alongside tobacco cigarettes (dual users). To the extent that dual users substantially lower the number of cigarettes, they will reduce health risks from smoking. However, from a medical point of view, exclusive vaping is preferable to dual use; (2) Methods: Using an online questionnaire we assessed behavioral, cognitive and attitudinal aspects of e-cig use in smoking and ex-smoking vapers; (3) Results: Our sample consisted of 19% dual users and 81% switchers. Before e-cig initiation, both groups smoked on average 22 cigarettes per day (CPD). After e-cig initiation, dual users decreased tobacco consumption by 82% and were low-to-moderately cigarette dependent. Both groups had been vaping for on average 22 months, were highly e-cig dependent, used state-of-the-art e-cigs, nicotine concentrations of 4-8 mg/mL and often flavors other than tobacco. Dual users used substantially less e-liquid per week than switchers but reported a similar number of puffs/day, experienced less e-cig efficacy, more practical problems, more negative and less positive consequences, and endorsed smoking reduction (rather than quitting) as a more important reason to start vaping. For both groups, e-cig risk perception was low and little stigmatization was experienced. Dual users preferred tobacco cigarettes in stressful situations and when rapid nicotine uptake is required. E-cigs were preferred where cigarettes are prohibited and to reduce second-hand smoke; (4) Conclusions: Differences between dual users and switchers center around variables proximal to the vaping behavior and its experienced effects rather than hinging on more general vaping-related beliefs and attitudes.

Immunological and toxicological risk assessment of e-cigarettes.

Science.gov (United States)

Kaur, Gagandeep; Pinkston, Rakeysha; Mclemore, Benathel; Dorsey, Waneene C; Batra, Sanjay

2018-03-31

Knowledge of the long-term toxicological and immunological effects of e-cigarette (e-cig) aerosols remains elusive due to the relatively short existence of vaping. Therefore, we performed a systematic search of articles published in public databases and analysed the research evidence in order to provide critical information regarding e-cig safety. Electronic nicotine delivery systems (or e-cigs) are an alternative to traditional cigarettes for the delivery of nicotine and are typically filled with glycerol or propylene glycol-based solutions known as e-liquids. Though present in lower quantities, e-cig aerosols are known to contain many of the harmful chemicals found in tobacco smoke. However, due to the paucity of experimental data and contradictory evidence, it is difficult to draw conclusive outcomes regarding toxicological, immunological and clinical impacts of e-cig aerosols. Excessive vaping has been reported to induce inflammatory responses including mitogen-activated protein kinase, Janus tyrosine kinase/signal transducer and activator of transcription and nuclear factor-κB signalling, similar to that induced by tobacco smoke. Based on recent evidence, prolonged exposure to some constituents of e-cig aerosols might result in respiratory complications such as asthma, chronic obstructive pulmonary disease and inflammation. Future studies are warranted that focus on establishing correlations between e-cig types, generations and e-liquid flavours and immunological and toxicological profiles to broaden our understanding about the effects of vaping. Copyright ©ERS 2018.

Immunological and toxicological risk assessment of e-cigarettes

Directory of Open Access Journals (Sweden)

Gagandeep Kaur

2018-02-01

Full Text Available Knowledge of the long-term toxicological and immunological effects of e-cigarette (e-cig aerosols remains elusive due to the relatively short existence of vaping. Therefore, we performed a systematic search of articles published in public databases and analysed the research evidence in order to provide critical information regarding e-cig safety. Electronic nicotine delivery systems (or e-cigs are an alternative to traditional cigarettes for the delivery of nicotine and are typically filled with glycerol or propylene glycol-based solutions known as e-liquids. Though present in lower quantities, e-cig aerosols are known to contain many of the harmful chemicals found in tobacco smoke. However, due to the paucity of experimental data and contradictory evidence, it is difficult to draw conclusive outcomes regarding toxicological, immunological and clinical impacts of e-cig aerosols. Excessive vaping has been reported to induce inflammatory responses including mitogen-activated protein kinase, Janus tyrosine kinase/signal transducer and activator of transcription and nuclear factor-κB signalling, similar to that induced by tobacco smoke. Based on recent evidence, prolonged exposure to some constituents of e-cig aerosols might result in respiratory complications such as asthma, chronic obstructive pulmonary disease and inflammation. Future studies are warranted that focus on establishing correlations between e-cig types, generations and e-liquid flavours and immunological and toxicological profiles to broaden our understanding about the effects of vaping.

Successful Nicotine Intake in Medical Assisted Use of E-Cigarettes: A Pilot Study

Directory of Open Access Journals (Sweden)

Roberta Pacifici

2015-07-01

Full Text Available The electronic cigarette (e-cig has gained popularity as an aid in smoking cessation programs mainly because it maintains the gestures and rituals of tobacco smoking. However, it has been shown in inexperienced e-cig users that ineffective nicotine delivery can cause tobacco craving that could be responsible for unsuccessful smoking reduction/cessation. Moreover, the incorrect use of an e-cig could also led to potential nicotine overdosage and intoxication. Medically assisted training on the proper use of an e-cig plus behavioral support for tobacco dependence could be a pivotal step in avoiding both issues. We performed an eight-month pilot study of adult smokers who started e-cig use after receiving a multi-component medically assisted training program with monitoring of nicotine intake as a biomarker of correct e-cig use. Participants were tested during follow-up for breath carbon monoxide (CO, plasma cotinine and trans-3’-hydroxycotinine, and number of tobacco cigarettes smoked. At the end of the first, fourth, and eighth month of follow-up, 91.1, 73.5, and 76.5% of participants respectively were e-cig users (‘only e-cig’ and ‘dual users’. They showed no significant variation in plasma cotinine and trans-3’-hydroxycotinine with respect to the start of the study when they smoked only tobacco cigarettes, but a significant reduction in breath CO. The proposed medically assisted training program of e-cig use led to a successful nicotine intake, lack of typical cigarette craving and overdosage symptoms and a significant decrease in the biomarker of cigarette combustion products.

Electronic cigarette: a threat or an opportunity for public health? State of the art and future perspectives.

Science.gov (United States)

Protano, C; Di Milia, L M; Orsi, G B; Vitali, M

2015-01-01

The e-cigarette, also known as e-cig, represents an emerging issue of great concern for public health. The aim of the present report was to explore the scientific literature about the use of electronic cigarette (e-cig), with a particular reference to the features of "toxicological safety", "effectiveness in overcoming the addiction to smoking the traditional cigarette" and "necessary research agenda". The efficacy of e-cig for smoking cessation is uncertain: some authors found that it can be a valid support, but long-term cessation rate has not be assessed. Other studies evidenced that e-cig is often used not for quitting smoking but to avoid smoking ban for traditional cigarettes and, even, some researches evidenced that it appears to contribute to nicotine addiction. E-cig smoking seems to be less dangerous of conventional cigarettes, but its use is not risk-free. Besides, cases of accidental or intentional poisoning with liquid solutions of e-cig have been reported. Also, the smoke of e-cig decreases indoor air quality, releasing particulate matter and other toxics that can persist on surfaces for days and generating passive exposure. These phenomena are similar to environmental tobacco smoke produced by conventional smoking, that is the sum of second- and third-hand smoke. We propose to call them "environmental electronic smoke", "electronic-second- hand smoke" and "electronic-third-hand smoke", respectively. Uncertainties relating to e-cig features determined the sequence, in the short term, of warnings and regulations approved and then replaced. In conclusion, although in recent years many researches were performed, evidences is limited and there is a need to study in deep all these issues.

Effect of sodium addition on Cu-deficient CuIn{sub 1-x}Ga{sub x}S{sub 2} thin film solar cells

Energy Technology Data Exchange (ETDEWEB)

Vasekar, Parag S.; Dhere, Neelkanth G. [Florida Solar Energy Center, University of Central Florida, 1679 Clearlake Road, Cocoa, FL 32922 (United States)

2009-01-15

Chalcopyrites are important contenders among solar-cell materials due to direct band gap and very high-absorption coefficients. Copper-indium-gallium disulfide (CIGS2) is a chalcopyrite material with a near-optimum band gap of 1.5 eV for terrestrial as well as space applications. At FSEC PV Materials Laboratory, record efficiency of 11.99% has been achieved on a 2.7 {mu}m CIGS2 thin film prepared by sulfurization. There are reports of influence of sodium on copper-indium-gallium selenide (CIGS) as well as copper-indium disulfide (CIS2) solar cells. However, this is the first of its kind approach to study the effect of sodium on CIGS2 solar cells and resulting in encouraging efficiencies. Copper-deficient CIGS2 thin films were prepared with and without the addition of sodium fluoride (NaF). Effects of addition of NaF on the microstructure and device electrical properties are presented in this work. (author)

Distinction of [220] and [204] textures of Cu(In,Ga)Se{sub 2} film and their growth behaviors depending on substrate nature and Na incorporation

Energy Technology Data Exchange (ETDEWEB)

Cho, Dae-Hyung, E-mail: dhcho@etri.re.kr [IT Components and Materials Industry Technology Research Department, Electronics and Telecommunications Research Institute (ETRI), 218 Gajeongno, Yuseong-gu, Daejeon 305-700 (Korea, Republic of); Kim, Jeha [Department of Solar & Energy Engineering, Cheongju University, 298 Daeseongro, Sangdang-gu, Cheongju, Chungbuk 360-764 (Korea, Republic of); Chung, Yong-Duck [IT Components and Materials Industry Technology Research Department, Electronics and Telecommunications Research Institute (ETRI), 218 Gajeongno, Yuseong-gu, Daejeon 305-700 (Korea, Republic of); Korea University of Science and Technology (UST), 217 Gajeongno, Yuseong-gu, Daejeon 305-350 (Korea, Republic of)

2015-08-31

For better understanding of the structural property of polycrystalline tetragonal Cu(In,Ga)Se{sub 2} (CIGS) thin films grown on soda-lime glass, it is necessary to characterize the [220]- and [204]-oriented textures clearly that are related to the different physical properties. However, the distinction between the [220]- and [204]-oriented textures is very difficult because of their nearly identical plane spacings and atomic arrangements. Using X-ray diffraction techniques of high resolution θ–2θ scanning and reciprocal space mapping, we distinguished the [220]- and [204]-oriented textures of CIGS films and observed that the behaviors of [220] and [204] textures independently depended on both substrate nature and Na presence. We report the Na- and substrate-related dependence of the physical properties of the CIGS film was attributed to the independent growth behaviors of the [220] and [204] textures in the CIGS. - Highlights: • We investigated [220]- and [204]-oriented textures of Cu(In,Ga)Se{sub 2} (CIGS) films. • X-ray diffraction methods distinguished two textures. • The growth behaviors were influenced by underlying substrate and Na. • The [220] and [204] textures in CIGS should be differentially observed.

Copper variation in Cu(In,Ga)Se{sub 2} solar cells with indium sulphide buffer layer

Energy Technology Data Exchange (ETDEWEB)

Spiering, S., E-mail: stefanie.spiering@zsw-bw.de [Zentrum für Sonnenenergie- und Wasserstoff-Forschung (ZSW) Baden-Wuerttemberg, Industriestrasse 6, 70565 Stuttgart (Germany); Paetel, S.; Kessler, F. [Zentrum für Sonnenenergie- und Wasserstoff-Forschung (ZSW) Baden-Wuerttemberg, Industriestrasse 6, 70565 Stuttgart (Germany); Igalson, M.; Abdel Maksoud, H. [Warsaw University of Technology (WUT), Faculty of Physics, Koszykowa 75, 00-662 Warszawa (Poland)

2015-05-01

In the manufacturing of Cu(In,Ga)Se{sub 2} (CIGS) thin film solar cells the application of a buffer layer on top of the absorber is essential to obtain high efficiency devices. Regarding the roll-to-roll production of CIGS cells and modules a vacuum deposition process for the buffer is preferable to the conventional cadmium sulphide buffer deposited in a chemical bath. Promising results have already been achieved for the deposition of indium sulphide buffer by different vacuum techniques. The solar device performance is very sensitive to the conditions at the absorber-buffer heterojunction. In view of optimization we investigated the influence of the Cu content in the absorber on the current-voltage characteristics. In this work the integral copper content was varied between 19 and 23 at.% in CIGS on glass substrates. An improvement of the cell performance by enhanced open circuit voltage was observed for a reduction to ~ 21 at.% when thermally evaporated indium sulphide was applied as the buffer layer. The influence of stoichiometry deviations on the transport mechanism and secondary barriers in the device was studied using detailed dark and light current-voltage analysis and admittance spectroscopy and compared to the reference CdS-buffered cells. We conclude that the composition of the absorber in the interface region affects current transport in In{sub x}S{sub y}-buffered and CdS-buffered cells in different ways hence optimal Cu content in those two types of devices is different. - Highlights: • Influence of Cu-variation in CIGS cells with In{sub x}S{sub y} buffer layer on cell performance • Enhanced efficiency by slight reduction of Cu-content to 21 at.% • Contribution of tunnelling-enhanced interface recombination for higher Cu-content.

Beneficial effect of post-deposition treatment in high-efficiency Cu(In,Ga)Se{sub 2} solar cells through reduced potential fluctuations

Energy Technology Data Exchange (ETDEWEB)

Jensen, S. A., E-mail: Soren.Jensen@nrel.gov, E-mail: Darius.Kuciauskas@nrel.gov; Glynn, S.; Kanevce, A.; Dippo, P.; Li, J. V.; Levi, D. H.; Kuciauskas, D., E-mail: Soren.Jensen@nrel.gov, E-mail: Darius.Kuciauskas@nrel.gov [National Renewable Energy Laboratory, 15013 Denver West Parkway, Golden, Colorado 80401 (United States)

2016-08-14

World-record power conversion efficiencies for Cu(In,Ga)Se{sub 2} (CIGS) solar cells have been achieved via a post-deposition treatment with alkaline metals, which increases the open-circuit voltage and fill factor. We explore the role of the potassium fluoride (KF) post-deposition treatment in CIGS by employing energy- and time-resolved photoluminescence spectroscopy and electrical characterization combined with numerical modeling. The bulk carrier lifetime is found to increase with post-deposition treatment from 255 ns to 388 ns, which is the longest charge carrier lifetime reported for CIGS, and within ∼40% of the radiative limit. We find evidence that the post-deposition treatment causes a decrease in the electronic potential fluctuations. These potential fluctuations have previously been shown to reduce the open-circuit voltage and the device efficiency in CIGS. Additionally, numerical simulations based on the measured carrier lifetimes and mobilities show a diffusion length of ∼10 μm, which is ∼4 times larger than the film thickness. Thus, carrier collection in the bulk is not a limiting factor for device efficiency. By considering differences in doping, bandgap, and potential fluctuations, we present a possible explanation for the voltage difference between KF-treated and untreated samples.

High performance systems

Energy Technology Data Exchange (ETDEWEB)

Vigil, M.B. [comp.

1995-03-01

This document provides a written compilation of the presentations and viewgraphs from the 1994 Conference on High Speed Computing given at the High Speed Computing Conference, {open_quotes}High Performance Systems,{close_quotes} held at Gleneden Beach, Oregon, on April 18 through 21, 1994.

Effectiveness of the Electronic Cigarette: An Eight-Week Flemish Study with Six-Month Follow-up on Smoking Reduction, Craving and Experienced Benefits and Complaints

Directory of Open Access Journals (Sweden)

Karolien Adriaens

2014-10-01

the end of the eight-month study, 19% of the e-cig groups and 25% of the control group were totally abstinent from smoking, while an overall reduction of 60% in the number of cigarettes smoked per day was observed (compared to intake. eCO levels decreased, whereas cotinine levels were the same in all groups at each moment of measurement. Reported benefits far outweighed the reported complaints. Conclusion: In a series of controlled lab sessions with e-cig naïve tobacco smokers, second generation e-cigs were shown to be immediately and highly effective in reducing abstinence induced cigarette craving and withdrawal symptoms, while not resulting in increases in eCO. Remarkable (>50 pc eight-month reductions in, or complete abstinence from tobacco smoking was achieved with the e-cig in almost half (44% of the participants.

Optical constants of Cu(In, Ga)Se{sub 2} for arbitrary Cu and Ga compositions

Energy Technology Data Exchange (ETDEWEB)

Minoura, Shota; Kodera, Keita; Nakane, Akihiro; Fujiwara, Hiroyuki, E-mail: fujiwara@gifu-u.ac.jp [Center of Innovative Photovoltaic Systems (CIPS), Gifu University, 1-1 Yanagido, Gifu 501-1193 (Japan); Maekawa, Takuji [Research and Development Headquarters, ROHM Co., Ltd., 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585 (Japan); Niki, Shigeru [Research Center for Photovoltaic Technologies, National Institute of Advanced Industrial Science and Technology (AIST), Central2, 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568 (Japan)

2015-05-21

The optical constants of Cu(In, Ga)Se{sub 2} (CIGS)-based polycrystalline layers with different Cu and Ga compositions are parameterized completely up to a photon energy of 6.5 eV assuming several Tauc-Lorentz transition peaks. Based on the modeled optical constants, we establish the calculation procedure for the CIGS optical constants in a two-dimensional compositional space of (Cu, Ga) by taking the composition-induced shift of the critical point energies into account. In particular, we find that the variation of the CIGS optical constants with the Cu composition can be modeled quite simply by a spectral-averaging method in which the dielectric function of the target Cu composition is estimated as a weighted average of the dielectric functions with higher and lower Cu compositions. To express the effect of the Ga composition, on the other hand, an energy shift model reported earlier is adopted. Our model is appropriate for a wide variety of CIGS-based materials having different Cu and Ga compositions, although the modeling error increases slightly at lower Cu compositions [Cu/(In + Ga) < 0.69]. From our model, the dielectric function, refractive index, extinction coefficient, and absorption coefficient for the arbitrary CIGS composition can readily be obtained. The optical database developed in this study is applied further for spectroscopic ellipsometry analyses of CIGS layers fabricated by single and multi-stage coevaporation processes. We demonstrate that the compositional and structural characterizations of the CIGS-based layers can be performed from established analysis methods.

Investigations of lateral and vertical compositional gradients in Cu(In,Ga)Se{sub 2} by highly spatially, spectrally and time resolved cathodoluminescence spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Mueller, Mathias; Ribbe, Stefan; Hempel, Thomas; Bertram, Frank; Christen, Juergen [Institute for Experimental Physics, Otto-von-Guericke-University, Magdeburg (Germany); Witte, Wolfram; Hariskos, Dimitrios [Zentrum fuer Sonnenenergie- und Wasserstoff-Forschung Baden-Wuerttemberg (ZSW), Stuttgart (Germany)

2011-07-01

Luminescence properties of Cu(In,Ga)Se{sub 2} (CIGS) layers with different thicknesses were investigated by means of highly spatially, spectrally and time resolved cathodoluminescence (CL) spectroscopy at low temperature (T=5 K). A polycrystalline CIGS thin film with a thickness of 2.4 {mu}m was grown using an in-line co-evaporation process with a final Cu-poor composition on top of a sputtered Mo layer on a soda lime glass substrate. The layer thickness was then reduced by highly controlled bromine methanol etching. The typical grainy (d{sub average}=3 {mu}m) structure of the untouched sample develops thin longish structures under the influence of the etchant. Integral CL spectra of the samples are dominated by donor-acceptor pair (DAP) luminescence. The peak energies of these spectra are ranging from 1.13 eV to 1.22 eV with decreasing layer thickness. The lateral distribution of the luminescence is inhomogeneous regarding the intensity as well as the peak energy. Time resolved CL shows a strong dependence of the initial lifetime from the emission energy.

Potential-induced degradation of Cu(In,Ga)Se2 photovoltaic modules

Science.gov (United States)

Yamaguchi, Seira; Jonai, Sachiko; Hara, Kohjiro; Komaki, Hironori; Shimizu-Kamikawa, Yukiko; Shibata, Hajime; Niki, Shigeru; Kawakami, Yuji; Masuda, Atsushi

2015-08-01

Potential-induced degradation (PID) of Cu(In,Ga)Se2 (CIGS) photovoltaic (PV) modules fabricated from integrated submodules is investigated. PID tests were performed by applying a voltage of -1000 V to connected submodule interconnector ribbons at 85 °C. The normalized energy conversion efficiency of a standard module decreases to 0.2 after the PID test for 14 days. This reveals that CIGS modules suffer PID under this experimental condition. In contrast, a module with non-alkali glass shows no degradation, which implies that the degradation occurs owing to alkali metal ions, e.g., Na+, migrating from the cover glass. The results of dynamic secondary ion mass spectrometry show Na accumulation in the n-ZnO transparent conductive oxide layer of the degraded module. A CIGS PV module with an ionomer (IO) encapsulant instead of a copolymer of ethylene and vinyl acetate shows no degradation. This reveals that the IO encapsulant can prevent PID of CIGS modules. A degraded module can recover from its performance losses by applying +1000 V to connected submodule interconnector ribbons from an Al plate placed on the test module.

Optical and electrical properties of electron-irradiated Cu(In,Ga)Se{sub 2} solar cells

Energy Technology Data Exchange (ETDEWEB)

Hirose, Y.; Warasawa, M. [Department of Electrical Engineering, Faculty of Science and Technology, Tokyo University of Science, 2641 Yamazaki, Noda 278-8510 (Japan); Takakura, K. [Department of Information, Communication and Electrical Engineering, Kumamoto National College of Technology, 2659-2 Suya, Koshi, Kumamoto 861-1102 (Japan); Kimura, S. [Department of Electrical Engineering, Faculty of Science and Technology, Tokyo University of Science, 2641 Yamazaki, Noda 278-8510 (Japan); Chichibu, S.F. [CANTech, Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, 2-1-1 Katahira, Aoba, Sendai 980-8577 (Japan); Ohyama, H. [Department of Information, Communication and Electrical Engineering, Kumamoto National College of Technology, 2659-2 Suya, Koshi, Kumamoto 861-1102 (Japan); Sugiyama, M., E-mail: mutsumi@rs.noda.tus.ac.jp [Department of Electrical Engineering, Faculty of Science and Technology, Tokyo University of Science, 2641 Yamazaki, Noda 278-8510 (Japan)

2011-08-31

The optical and electrical properties of electron-irradiated Cu(In,Ga)Se{sub 2} (CIGS) solar cells and the thin films that composed the CIGS solar cell structure were investigated. The transmittance of indium tin oxide (ITO), ZnO:Al, ZnO:Ga, undoped ZnO, and CdS thin films did not change for a fluence of up to 1.5 x 10{sup 18} cm{sup -2}. However, the resistivity of ZnO:Al and ZnO:Ga, which are generally used as window layers for CIGS solar cells, increased with increasing irradiation fluence. For CIGS thin films, the photoluminescence peak intensity due to Cu-related point defects, which do not significantly affect solar cell performance, increased with increasing electron irradiation. In CIGS solar cells, decreasing J{sub SC} and increasing R{sub s} reflected the influence of irradiated ZnO:Al, and decreasing V{sub OC} and increasing R{sub sh} mainly tended to reflect the pn-interface properties. These results may indicate that the surface ZnO:Al thin film and several heterojunctions tend to degrade easily by electron irradiation as compared with the bulk of semiconductor-composed solar cells.

Exposure to electronic cigarettes impairs pulmonary anti-bacterial and anti-viral defenses in a mouse model.

Directory of Open Access Journals (Sweden)

Thomas E Sussan

Full Text Available Electronic cigarettes (E-cigs have experienced sharp increases in popularity over the past five years due to many factors, including aggressive marketing, increased restrictions on conventional cigarettes, and a perception that E-cigs are healthy alternatives to cigarettes. Despite this perception, studies on health effects in humans are extremely limited and in vivo animal models have not been generated. Presently, we determined that E-cig vapor contains 7 x 10(11 free radicals per puff. To determine whether E-cig exposure impacts pulmonary responses in mice, we developed an inhalation chamber for E-cig exposure. Mice that were exposed to E-cig vapor contained serum cotinine concentrations that are comparable to human E-cig users. E-cig exposure for 2 weeks produced a significant increase in oxidative stress and moderate macrophage-mediated inflammation. Since, COPD patients are susceptible to bacterial and viral infections, we tested effects of E-cigs on immune response. Mice that were exposed to E-cig vapor showed significantly impaired pulmonary bacterial clearance, compared to air-exposed mice, following an intranasal infection with Streptococcus pneumonia. This defective bacterial clearance was partially due to reduced phagocytosis by alveolar macrophages from E-cig exposed mice. In response to Influenza A virus infection, E-cig exposed mice displayed increased lung viral titers and enhanced virus-induced illness and mortality. In summary, this study reports a murine model of E-cig exposure and demonstrates that E-cig exposure elicits impaired pulmonary anti-microbial defenses. Hence, E-cig exposure as an alternative to cigarette smoking must be rigorously tested in users for their effects on immune response and susceptibility to bacterial and viral infections.

Electrochemical etching of molybdenum for shunt removal in thin film solar cells

NARCIS (Netherlands)

Hovestad, A.; Bressers, P.M.M.C.; Meertens, R.M.; Frijters, C.H.; Voorthuijzen, W.P.

2015-01-01

High yield and reproducible production is a major challenge in up-scaling thin film Cu(In,Ga)Se2(CIGS) solar cells to large area roll-to-roll industrial manufacturing. Pinholes enabling Ohmic contact between the ZnO:Al front-contact and Mo back contact of the CIGS cell create electrical shunts that

Preparation and Characterization of Molybdenum Thin Film to Photovoltaic applications; Preparacion y Caracterizacion de Peliculas Delgadas de Molibdeno para Aplicaciones Fotovoltaicas

Energy Technology Data Exchange (ETDEWEB)

Andres, M.; Gutierrez, M. T.

2007-09-18

Molybdenum (Mo) is one of the main material used as back ohmic contact for Cu(In,Ga)Se2 (CIGS) thin film solar cells. It has to provide the electrical properties of low resistivity electrode and high reflectance in the absorbance region of CIGS layer. Also, it has to have high thermal stability, an adequate morphology and good adhesion to the substrate. The aim of this work has been the preparation of Mo layers onto two types of substrates, soda-lime glass (SLG) and a commercial flexible polyimide called Kapton, and the evaluation as a flexible substrate in CIGS solar cells. Internal stress, adhesion, microstructure and optical and electrical properties of Mo thin films have been studied as a function of deposition parameters (gas pressure, power density and time). The change of the substrate from rigid one to flexible introduces tensile stress due to the difference in the coefficient of thermal expansion (CTE) between the coating and the substrate. Low stress in Mo/Kapton structure has been obtained; this is a good result to use in CIGS flexible solar cells. (Author) 23 refs.

Monitoring nicotine intake from e-cigarettes: measurement of parent drug and metabolites in oral fluid and plasma.

Science.gov (United States)

Papaseit, Esther; Farré, Magí; Graziano, Silvia; Pacifici, Roberta; Pérez-Mañá, Clara; García-Algar, Oscar; Pichini, Simona

2017-03-01

Electronic cigarettes (e-cig) known as electronic nicotine devices recently gained popularity among smokers. Despite many studies investigating their safety and toxicity, few examined the delivery of e-cig-derived nicotine and its metabolites in alternative biological fluids. We performed a randomized, crossover, and controlled clinical trial in nine healthy smokers. Nicotine (NIC), cotinine (COT), and trans-3'-hydroxycotinine (3-HCOT) were measured in plasma and oral fluid by liquid chromatography-tandem mass spectrometry after consumption of two consecutive e-cig administrations or two consecutive tobacco cigarettes. NIC and its metabolites were detected both in oral fluid and plasma following both administration conditions. Concentrations in oral fluid resulted various orders of magnitude higher than those observed in plasma. Oral fluid concentration of tobacco cigarette and e-cig-derived NIC peaked at 15 min after each administration and ranged between 1.0 and 1396 μg/L and from 0.3 to 860 μg/L; those of COT between 52.8 and 110 μg/L and from 33.8 to 94.7 μg/L; and those of 3-HCOT between 12.4 and 23.5 μg/L and from 8.5 to 24.4 μg/L. The oral fluid to plasma concentration ratio of both e-cig- and tobacco cigarette-derived NIC peaked at 15 min after both administrations and correlated with oral fluid NIC concentration. The obtained results support the measurement of NIC and metabolites in oral fluid in the assessment of intake after e-cig use and appear to be a suitable alternative to plasma when monitoring nicotine delivery from e-cig for clinical and toxicological studies.

Layer-by-Layer Nanoassembly of Copper Indium Gallium Selenium Nanoparticle Films for Solar Cell Applications

Directory of Open Access Journals (Sweden)

A. Hemati

2012-01-01

Full Text Available Thin films of CIGS nanoparticles interdigited with polymers have been fabricated through a cost-effective nonvacuum film deposition process called layer-by-layer (LbL nanoassembly. CIGS nanoparticles synthesized by heating copper chloride, indium chloride, gallium chloride, and selenium in oleylamine were dispersed in water, and desired surface charges were obtained through pH regulation and by coating the particles with polystyrene sulfonate (PSS. Raising the pH of the nanoparticle dispersion reduced the zeta-potential from +61 mV at pH 7 to −51 mV at pH 10.5. Coating the CIGS nanoparticles with PSS (CIGS-PSS produced a stable dispersion in water with −56.9 mV zeta-potential. Thin films of oppositely charged CIGS nanoparticles (CIGS/CIGS, CIGS nanoparticles and PSS (CIGS/PSS, and PSS-coated CIGS nanoparticles and polyethylenimine (CIGS-PSS/PEI were constructed through the LbL nanoassembly. Film thickness and resistivity of each bilayer of the films were measured, and photoelectric properties of the films were studied for solar cell applications. Solar cell devices fabricated with a 219 nm CIGS film, when illuminated by 50 W light-source, produced 0.7 V open circuit voltage and 0.3 mA/cm2 short circuit current density.

Effects of Sb-doping on the grain growth of Cu(In, Ga)Se2 thin films fabricated by means of single-target sputtering

International Nuclear Information System (INIS)

Zhang, Shu; Wu, Lu; Yue, Ruoyu; Yan, Zongkai; Zhan, Haoran; Xiang, Yong

2013-01-01

To investigate the effects of Sb doping on the kinetics of grain growth in Cu(In,Ga)Se 2 (CIGS) thin films during annealing, CIGS thin films were sputtered onto Mo coated substrates from a single CIGS alloy target, followed by chemical bath deposition of Sb 2 S 3 thin layers on top of CIGS layers and subsequent annealing at different temperatures for 30 min in Se vapors. X-ray diffraction results showed that CIGS thin films were obtained directly using the single-target sputtering method. After annealing, the In/Ga ratio in Sb-doped CIGS thin films remained stable compared to undoped film, possibly because Sb can promote the incorporation of Ga into CIGS. The grain growth in CIGS thin films was enhanced after Sb doping, exhibiting significantly larger grains after annealing at 400 °C or 450 °C compared to films without Sb. In particular, the effect was strikingly significant in grain growth across the film thickness, resulting in columnar grain structure in Sb-doped films. This grain growth improvement may be led by the diffusion of Sb from the front surface to the CIGS-Mo back interface, which promoted the mass transport process in CIGS thin films. - Highlights: ► Cu(In,Ga)Se 2 (CIGS) thin films made by sputtering from a single CIGS target. ► Chemical bath deposition used to introduce antimony into CIGS absorber layers. ► In/Ga ratio decreases in Sb-doped annealed films, comparatively to undoped films. ► Sb-doped CIGS films are superior to undoped films in terms of grain-growth kinetics

Study on analytical modelling approaches to the performance of thin film PV modules in sunny inland climates

International Nuclear Information System (INIS)

Torres-Ramírez, M.; Nofuentes, G.; Silva, J.P.; Silvestre, S.; Muñoz, J.V.

2014-01-01

This work is aimed at verifying that analytical modelling approaches may provide an estimation of the outdoor performance of TF (thin film) PV (photovoltaic) technologies in inland sites with sunny climates with adequate accuracy for engineering purposes. Osterwald's and constant fill factor methods were tried to model the maximum power delivered and the annual energy produced by PV modules corresponding to four TF PV technologies. Only calibrated electrical parameters at STC (standard test conditions), on-plane global irradiance and module temperature are required as inputs. A 12-month experimental campaign carried out in Madrid and Jaén (Spain) provided the necessary data. Modelled maximum power and annual energy values obtained through both methods were statistically compared to the experimental ones. In power terms, the RMSE (root mean square error) stays below 3.8% and 4.5% for CdTe (cadmium telluride) and CIGS (copper indium gallium selenide sulfide) PV modules, respectively, while RMSE exceeds 5.4% for a-Si (amorphous silicon) or a-Si:H/μc-Si PV modules. Regarding energy terms, errors lie below 4.0% in all cases. Thus, the methods tried may be used to model the outdoor behaviour of the a-Si, a-Si:H/μc-Si, CIGS and CdTe PV modules tested – ordered from the lowest to the highest accuracy obtained – in sites with similar spectral characteristics to those of the two sites considered. - Highlights: • Simple analytical methods to model the outdoor behaviour of thin film PV (photovoltaic) technologies. • 8 PV modules were deployed outdoors over a 12-month period in two sunny inland sites. • RMSE (root mean square error) values stay below 3.8% and 4.5% in CdTe (cadmium telluride) and CIGS (copper indium gallium selenide sulfide) PV modules. • Errors remain below 4.0% for all the PV modules and sites in energy terms. • Simple methods: suitable estimation of PV outdoor behaviour for engineering purposes

High performance work practices, innovation and performance

DEFF Research Database (Denmark)

Jørgensen, Frances; Newton, Cameron; Johnston, Kim

2013-01-01

Research spanning nearly 20 years has provided considerable empirical evidence for relationships between High Performance Work Practices (HPWPs) and various measures of performance including increased productivity, improved customer service, and reduced turnover. What stands out from......, and Africa to examine these various questions relating to the HPWP-innovation-performance relationship. Each paper discusses a practice that has been identified in HPWP literature and potential variables that can facilitate or hinder the effects of these practices of innovation- and performance...

In Situ and Ex Situ Studies of Molybdenum Thin Films Deposited by rf and dc Magnetron Sputtering as a Back Contact for CIGS Solar Cells

Directory of Open Access Journals (Sweden)

K. Aryal

2012-01-01

Full Text Available Molybdenum thin films were deposited by rf and dc magnetron sputtering and their properties analyzed with regards to their potential application as a back contact for CIGS solar cells. It is shown that both types of films tend to transition from tensile to compressive strain when the deposition pressure increases, while the conductivity and the grain size decreas. The nucleation of the films characterized by in situ and real time spectroscopic ellipsometry shows that both films follow a Volmer-Weber growth, with a higher surface roughness and lower deposition rate for the rf deposited films. The electronic relaxation time was then extracted as a function of bulk layer thickness for rf and dc films by fitting each dielectric function to a Drude free-electron model combined with a broad Lorentz oscillator. The values were fitted to a conical growth mode and demonstrated that the rf-deposited films have already smaller grains than the dc films when the bulk layer thickness is 30 nm.

Shunt resistance and saturation current determination in CdTe and CIGS solar cells. Part 2: application to experimental IV measurements and comparison with other methods

Science.gov (United States)

Rangel-Kuoppa, Victor-Tapio; Albor-Aguilera, María-de-Lourdes; Hérnandez-Vásquez, César; Flores-Márquez, José-Manuel; Jiménez-Olarte, Daniel; Sastré-Hernández, Jorge; González-Trujillo, Miguel-Ángel; Contreras-Puente, Gerardo-Silverio

2018-04-01

In this Part 2 of this series of articles, the procedure proposed in Part 1, namely a new parameter extraction technique of the shunt resistance (R sh ) and saturation current (I sat ) of a current-voltage (I-V) measurement of a solar cell, within the one-diode model, is applied to CdS-CdTe and CIGS-CdS solar cells. First, the Cheung method is used to obtain the series resistance (R s ) and the ideality factor n. Afterwards, procedures A and B proposed in Part 1 are used to obtain R sh and I sat . The procedure is compared with two other commonly used procedures. Better accuracy on the simulated I-V curves used with the parameters extracted by our method is obtained. Also, the integral percentage errors from the simulated I-V curves using the method proposed in this study are one order of magnitude smaller compared with the integral percentage errors using the other two methods.

Health professionals in Flanders perceive the potential health risks of vaping as lower than those of smoking but do not recommend using e-cigarettes to their smoking patients.

Science.gov (United States)

Van Gucht, Dinska; Baeyens, Frank

2016-06-24

Many misperceptions of both risks and opportunities of e-cigarettes (e-cigs) exist among the general population and among physicians, although e-cigs could be a valuable harm reduction tool for current smokers. Two groups in Flanders, namely general practitioners (GPs; family doctors) and tobacco counselors filled out an online questionnaire with regard to their attitudes and risk perceptions concerning e-cigs. Statements included were on the safety and the addictive properties of e-cigs in absolute terms, whereas other items compared e-cigs with regular tobacco cigarettes. Statements about possible "gateway" and "renormalization" effects, selling to minors, and use in public places and on the potential of e-cigs as a smoking cessation aid were also included. Respondents were also asked for the rate at which their patients asked information about e-cigs, if they would recommend e-cigs to their smoking patients, and whether they had information brochures on e-cigs. About 70 % believed that e-cigs are harmful to vapers, and about half to two thirds believed that e-cigs are carcinogenic, increase cardiovascular risk, and increase the risk of chronic lung disease. Also, a substantial minority incorrectly believed these risks to be no less than those resulting from regular smoking. Ten to almost 20 % disagreed that e-cigs are healthier and represent less risk for the main serious smoking-related diseases than conventional cigarettes. More than half of the respondents disagreed that e-cigs are an effective smoking cessation aid. None (0 %) offered the strongest level of agreement for recommending e-cigs to their clients/patients, but GPs agreed to a lesser degree a bit more often than tobacco counselors. Almost none had information leaflets for potentially interested patients. Finally, the majority of our sample also believed that e-cigs will cause renormalization of smoking and that e-cigs will lead to an uptake of conventional smoking and disagreed with allowing

Final Report: Rational Design of Wide Band Gap Buffer Layers for High-Efficiency Thin-Film Photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Lordi, Vincenzo [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2016-09-30

The main objective of this project is to enable rational design of wide band gap buffer layer materials for CIGS thin-film PV by building understanding of the correlation of atomic-scale defects in the buffer layer and at the buffer/absorber interface with device electrical properties. Optimized wide band gap buffers are needed to reduce efficiency loss from parasitic absorption in the buffer. The approach uses first-principles materials simulations coupled with nanoscale analytical electron microscopy as well as device electrical characterization. Materials and devices are produced by an industrial partner in a manufacturing line to maximize relevance, with the goal of enabling R&D of new buffer layer compositions or deposition processes to push device efficiencies above 21%. Cadmium sulfide (CdS) is the reference material for analysis, as the prototypical high-performing buffer material.

Electronic Cigarettes: Their Constituents and Potential Links to Asthma.

Science.gov (United States)

Clapp, Phillip W; Jaspers, Ilona

2017-10-05

Vaping is gaining popularity in the USA, particularly among teens and young adults. While e-cigs are commonly represented as safer alternatives to tobacco cigarettes, little is known regarding the health effects of their short- or long-term use, especially in individuals with pre-existing respiratory diseases such as asthma. Flavored e-cig liquids (e-liquids) and e-cig aerosols contain airway irritants and toxicants that have been implicated in the pathogenesis and worsening of lung diseases. In this review, we will summarize existing data on potential health effects of components present in e-cig aerosols, such as propylene glycol, vegetable glycerin, nicotine, and flavorings, and discuss their relevance in the context of asthma. Recent survey data indicate that adolescents with asthma had a higher prevalence of current e-cig use (12.4%) compared to their non-asthmatics peers (10.2%) and conveyed positive beliefs about tobacco products, especially e-cigs. Similarly, a study conducted among high school students from Ontario, Canada, indicated a greater likelihood of e-cig use in asthmatics as compared to their non-asthmatic peers. Availability of different flavorings is often cited as the main reason among youth/adolescents for trying e-cigs or switching from cigarettes to e-cigs. Occupational inhalation of some common food-safe flavoring agents is reported to cause occupational asthma and worsen asthmatic symptoms. Moreover, workplace inhalation exposures to the flavoring agent diacetyl have caused irreversible obstructive airway disease in healthy workers. Additionally, recent studies report that thermal decomposition of propylene glycol (PG) and vegetable glycerin (VG), the base constituents of e-liquids, produces reactive carbonyls, including acrolein, formaldehyde, and acetaldehyde, which have known respiratory toxicities. Furthermore, recent nicotine studies in rodents reveal that prenatal nicotine exposures lead to epigenetic reprogramming in the offspring

Impedance-Based Stability Analysis in Grid Interconnection Impact Study Owing to the Increased Adoption of Converter-Interfaced Generators

Directory of Open Access Journals (Sweden)

Youngho Cho

2017-09-01

Full Text Available This study investigates the emerging harmonic stability concerns to be addressed by grid planners in generation interconnection studies, owing to the increased adoption of renewable energy resources connected to the grid via power electronic converters. The wideband and high-frequency electromagnetic transient (EMT characteristics of these converter-interfaced generators (CIGs and their interaction with the grid impedance are not accurately captured in the typical dynamic studies conducted by grid planners. This paper thus identifies the desired components to be studied and subsequently develops a practical process for integrating a new CIG into a grid with the existing CIGs. The steps of this process are as follows: the impedance equation of a CIG using its control dynamics and an interface filter to the grid, for example, an LCL filter (inductor-capacitor-inductor type, is developed; an equivalent impedance model including the existing CIGs nearby and the grid observed from the point of common coupling are derived; the system stability for credible operating scenarios is assessed. Detailed EMT simulations validate the accuracy of the impedance models and stability assessment for various connection scenarios. By complementing the conventional EMT simulation studies, the proposed analytical approach enables grid planners to identify critical design parameters for seamlessly integrating a new CIG and ensuring the reliability of the grid.

CIS Photovoltaic Technology; Final Technical Report 12 January 1997 - 15 April 1998

International Nuclear Information System (INIS)

Delahoy, A.E.; Britt, J.S.; Kiss, Z.J.

1998-01-01

This report describes work performed by Energy Photovoltaics, Inc. (EPV) during the third phase of a three-phase, cost-shared subcontract. Researchers at EPV explored novel sequential formation recipes for CIGS that can be implemented on a unique pilot line constructed to coat low-cost, glass substrates 4300 cm2 in area; implemented a particular CIGS recipe on the pilot line that enabled large-area modules to be prepared with efficiencies up to 7.6%; and performed electrical resistance monitoring of the film that proved capable of indicating the temperature of compound formation and detecting termination. The substrate/Mo/Na working group (which included EPV, NREL, and others) studied Na in Mo and the effect of Na on devices, and found it beneficial except at concentrations exceeding 0.4%. Researchers determined the following properties of large-area, magnetron-sputtered ZnO:Al: sheet resistance 24 W/sq., transmission 82%, conductivity 440 S cm-1; and preheating the glass increases the conductivity. Devices prepared using a baseline CIGS process averaged 11.7% in efficiency. Modules and mini-modules were prepared using a diode-laser-pumped yttrium-aluminum-garnet laser for the Mo patterning and mechanical scribing for the cuts. Large-area CIGS formation involves the use of linear sources, and thickness profiles were presented for simple and optimized linear sources. An unencapsulated module producing 25 watts (7.65% aperture-area efficiency) was produced. Using a new diagnostic technique, the fill factor of a CIGS module was decomposed into contributions from the intrinsic device fill factor and ZnO sheet resistance

Investigating the electronic properties of Al2O3/Cu(In,GaSe2 interface

Directory of Open Access Journals (Sweden)

R. Kotipalli

2015-10-01

Full Text Available Atomic layer deposited (ALD Al2O3 films on Cu(In,GaSe2 (CIGS surfaces have been demonstrated to exhibit excellent surface passivation properties, which is advantageous in reducing recombination losses at the rear metal contact of CIGS thin-film solar cells. Here, we report, for the first time, experimentally extracted electronic parameters, i.e. fixed charge density (Qf and interface-trap charge density (Dit, for as-deposited (AD and post-deposition annealed (PDA ALD Al2O3 films on CIGS surfaces using capacitance–voltage (C-V and conductance-frequency (G-f measurements. These results indicate that the AD films exhibit positive fixed charges Qf (approximately 1012 cm−2, whereas the PDA films exhibit a very high density of negative fixed charges Qf (approximately 1013 cm−2. The extracted Dit values, which reflect the extent of chemical passivation, were found to be in a similar range of order (approximately 1012 cm−2 eV−1 for both AD and PDA samples. The high density of negative Qf in the bulk of the PDA Al2O3 film exerts a strong Coulomb repulsive force on the underlying CIGS minority carriers (ns, preventing them to recombine at the CIGS/Al2O3 interface. Using experimentally extracted Qf and Dit values, SCAPS simulation results showed that the surface concentration of minority carriers (ns in the PDA films was approximately eight-orders of magnitude lower than in the AD films. The electrical characterization and estimations presented in this letter construct a comprehensive picture of the interfacial physics involved at the Al2O3/CIGS interface.

RavenDB high performance

CERN Document Server

Ritchie, Brian

2013-01-01

RavenDB High Performance is comprehensive yet concise tutorial that developers can use to.This book is for developers & software architects who are designing systems in order to achieve high performance right from the start. A basic understanding of RavenDB is recommended, but not required. While the book focuses on advanced topics, it does not assume that the reader has a great deal of prior knowledge of working with RavenDB.

Microstructure characterization of the soda-lime-glass/copper-indium-gallium-selenium interface in Cu-poor Cu(In,Ga)Se{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Wang, Jian, E-mail: wangjustb@gmail.com; Qiao, Yi; Zhu, Jie, E-mail: jiezhu@ustb.edu.cn

2015-05-29

The microstructure characteristics of the soda-lime-glass/Cu(In,Ga)Se{sub 2} (SLG/CIGS) interface in Cu-poor CIGS films are investigated by transmission electron microscopy and selected area electronic diffraction (SAED). The SAED patterns show very sharp and strong spots, indicating the main structure of CIGS chalcopyrite. Small dispersed crystals with size distribution from 2 to 5 nm seem to be embedded in amorphous matrix, and additional spots indicate the presence of an ordered vacancy compound (OVC). This observation is consistent with the Raman results, and the OVC phase with the nanoclusters exists in the CIGS matrix, instead of layer structure. Lattice distortion results in local changes in contrast. Some pseudo-disordered structure is observed, however, the structure is actually the chalcopyrite CIGS structure. 180° rotation twins are also observed at the SLG/CIGS interface. Lattice distortion is widely observed at the interface of the Cu-poor CIGS films, and the extra spots could be caused by different lattice orientations. - Highlights: • Cu(In,Ga)Se{sub 2} (CIGS) were prepared on bare soda-lime-glass (SLG) substrates. • Microstructure of the SLG/CIGS interface was investigated. • An ordered vacancy compound (OVC) phase was observed. • The OVC phase with nanoclusters exists in the CIGS matrix, instead of layer structure. • 180° rotation twins were observed at the SLG/CIGS interface.

The Energy and Environmental Performance of Ground-Mounted Photovoltaic Systems—A Timely Update

Directory of Open Access Journals (Sweden)

Enrica Leccisi

2016-08-01

Full Text Available Given photovoltaics’ (PVs constant improvements in terms of material usage and energy efficiency, this paper provides a timely update on their life-cycle energy and environmental performance. Single-crystalline Si (sc-Si, multi-crystalline Si (mc-Si, cadmium telluride (CdTe and copper indium gallium diselenide (CIGS systems are analysed, considering the actual country of production and adapting the input electricity mix accordingly. Energy pay-back time (EPBT results for fixed-tilt ground mounted installations range from 0.5 years for CdTe PV at high-irradiation (2300 kWh/(m2·yr to 2.8 years for sc-Si PV at low-irradiation (1000 kWh/(m2·yr, with corresponding quality-adjusted energy return on investment (EROIPE-eq values ranging from over 60 to ~10. Global warming potential (GWP per kWhel averages out at ~30 g(CO2-eq, with lower values (down to ~10 g for CdTe PV at high irradiation, and up to ~80 g for Chinese sc-Si PV at low irradiation. In general, results point to CdTe PV as the best performing technology from an environmental life-cycle perspective, also showing a remarkable improvement for current production modules in comparison with previous generations. Finally, we determined that one-axis tracking installations can improve the environmental profile of PV systems by approximately 10% for most impact metrics.

Metastable Electrical Characteristics of Polycrystalline Thin-Film Photovoltaic Modules upon Exposure and Stabilization: Preprint

Energy Technology Data Exchange (ETDEWEB)

Deline, C. A.; del Cueto, J. A.; Albin, D. S.; Rummel, S. R.

2011-09-01

The significant features of a series of stabilization experiments conducted at the National Renewable Energy Laboratory (NREL) between May 2009 and the present are reported. These experiments evaluated a procedure to stabilize the measured performance of thin-film polycrystalline cadmium telluride (CdTe) and copper indium gallium diselenide (CIGS) thin-film photovoltaic (PV) modules. The current-voltage (I-V) characteristics of CdTe and CIGS thin-film PV devices and modules exhibit transitory changes in electrical performance after thermal exposure in the dark and/or bias and light exposures. We present the results of our case studies of module performance versus exposure: light-soaked at 65 degrees C; exposed in the dark under forward bias at 65 degrees C; and, finally, longer-term outdoor exposure. We find that stabilization can be achieved to varying degrees using either light-soaking or dark bias methods and that the existing IEC 61646 light-soaking interval may be appropriate for CdTe and CIGS modules with one caveat: it is likely that at least three exposure intervals are required for stabilization.

Evaluación de la fractura por fatiga del cigüeñal de un motor Diesel. // Evaluation of the crank shaft fatigue failure of a boat diesel engine.

Directory of Open Access Journals (Sweden)

R. A. Goytisolo Espinosa

2005-05-01

Full Text Available En el Trabajo se presentan los resultados de una investigación realizada por el colectivo de Mecánica Aplicada de laFacultad de Ingeniería Mecánica de La Universidad de Cienfuegos, con vistas a esclarecer la causa de la fractura delcigüeñal de uno de los motores de la Moto Nave “Mar del Sur” de le Empresa EQUITALL.La investigación del material del cigüeñal arrojó que se trata de acero 30. Los cálculos realizados demostraron, que lacapacidad resistente de este acero es insuficiente para soportar las tensiones que se desarrollan en el codo de salida delcigüeñal y los factores de seguridad a la fatiga en algunos de los puntos mas críticos del cachete, por donde se produjo lafractura, dan inferiores a la unidad y la aplicación de la Mecánica de la Fractura Subcrítica, confirmó que la Vida Útil delárbol con dicho material, es muy limitada.Palabras claves: Cigüeñal diesel, fractura por fatiga, mecánica de la fractura subcrítica.__________________________________________________________________________Abstract.This research paper shows the results of an investigation carried out by the Applied Mechanics staff of the MechanicalEngineering faculty of the Cienfuegos University. It was developed in order to determine the crankshaft failure causes ofengines of a boat diesel engine.The crankshaft material investigation showed that it was steel grade 30. The calculations showed that the steel resistancecapacity is not enough to support the stresses produced in the crankshaft output elbow. The fatigue security factors in someof the most critical areas of the cheek, where the failure took place, are lower than unity. The subcritical fracture mechanicsapplication confirmed that the shaft working life is quite limited with this steel.Key words: Diesel crankshaft, fatigue fracture, subcritical fracture mechanics.

High-performance computing using FPGAs

CERN Document Server

Benkrid, Khaled

2013-01-01

This book is concerned with the emerging field of High Performance Reconfigurable Computing (HPRC), which aims to harness the high performance and relative low power of reconfigurable hardware–in the form Field Programmable Gate Arrays (FPGAs)–in High Performance Computing (HPC) applications. It presents the latest developments in this field from applications, architecture, and tools and methodologies points of view. We hope that this work will form a reference for existing researchers in the field, and entice new researchers and developers to join the HPRC community.  The book includes:  Thirteen application chapters which present the most important application areas tackled by high performance reconfigurable computers, namely: financial computing, bioinformatics and computational biology, data search and processing, stencil computation e.g. computational fluid dynamics and seismic modeling, cryptanalysis, astronomical N-body simulation, and circuit simulation.     Seven architecture chapters which...

Shunt resistance and saturation current determination in CdTe and CIGS solar cells. Part 1: a new theoretical procedure and comparison with other methodologies

Science.gov (United States)

Rangel-Kuoppa, Victor-Tapio; Albor-Aguilera, María-de-Lourdes; Hérnandez-Vásquez, César; Flores-Márquez, José-Manuel; González-Trujillo, Miguel-Ángel; Contreras-Puente, Gerardo-Silverio

2018-04-01

A new proposal for the extraction of the shunt resistance (R sh ) and saturation current (I sat ) of a current-voltage (I-V) measurement of a solar cell, within the one-diode model, is given. First, the Cheung method is extended to obtain the series resistance (R s ), the ideality factor (n) and an upper limit for I sat . In this article which is Part 1 of two parts, two procedures are proposed to obtain fitting values for R sh and I sat within some voltage range. These two procedures are used in two simulated I-V curves (one in darkness and the other one under illumination) to recover the known solar cell parameters R sh , R s , n, I sat and the light current I lig and test its accuracy. The method is compared with two different common parameter extraction methods. These three procedures are used and compared in Part 2 in the I-V curves of CdS-CdTe and CIGS-CdS solar cells.

High-Performance Networking

CERN Multimedia

CERN. Geneva

2003-01-01

The series will start with an historical introduction about what people saw as high performance message communication in their time and how that developed to the now to day known "standard computer network communication". It will be followed by a far more technical part that uses the High Performance Computer Network standards of the 90's, with 1 Gbit/sec systems as introduction for an in depth explanation of the three new 10 Gbit/s network and interconnect technology standards that exist already or emerge. If necessary for a good understanding some sidesteps will be included to explain important protocols as well as some necessary details of concerned Wide Area Network (WAN) standards details including some basics of wavelength multiplexing (DWDM). Some remarks will be made concerning the rapid expanding applications of networked storage.

Effect of thermal annealing on the redistribution of alkali metals in Cu(In,Ga)Se2 solar cells on glass substrate

Science.gov (United States)

Kamikawa, Yukiko; Nishinaga, Jiro; Ishizuka, Shogo; Tayagaki, Takeshi; Guthrey, Harvey; Shibata, Hajime; Matsubara, Koji; Niki, Shigeru

2018-03-01

The precise control of alkali-metal concentrations in Cu(In,Ga)Se2 (CIGS) solar cells via post deposition treatment (PDT) has recently attracted attention. When PDT is performed at an elevated temperature, an accompanying annealing effect is expected. Here, we investigate how thermal annealing affects the redistribution of alkali metals in CIGS solar cells on glass substrates and the properties of the solar cells. In addition, we investigate the origin of non-homogeneous alkali-metal depth profiles that are typical of CIGS grown using a three-stage process. In particular, we use secondary-ion mass spectrometry measurements of the ion concentration as a function of distance from the CIGS surface to investigate the impact of thermal annealing on the distribution of alkali metals (Na, Ka, and Rb) and constituent elements (Ga and In) in the CIGS absorbers. We find that the depth profiles of the alkali metals strongly reflect the density of sites that tend to accommodate alkali metals, i.e., vacancies. Annealing at elevated temperature caused a redistribution of the alkali metals. The thermal-diffusion kinetics of alkali metals depends strongly on the species involved. We introduced low flux potassium fluoride (KF) to study a side effect of KF-PDT, i.e., Na removal from CIGS, separately from its predominant effects such as surface modification. When sufficient amounts of Na are supplied from the soda lime glass via annealing at an elevated temperature, the negative effect was not apparent. Conversely, when the Na supply was not sufficient, it caused a deterioration of the photovoltaic properties.

Effect of Thermal Annealing on the Redistribution of Alkali Metals in Cu(In,Ga)Se2 Solar Cells on Glass Substrate

Energy Technology Data Exchange (ETDEWEB)

Guthrey, Harvey L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kamikawa, Yukiko [National Institute of Advanced Industrial Science and Technology (AIST); Nishinaga, Jiro [National Institute of Advanced Industrial Science and Technology (AIST); Ishizuka, Shogo [National Institute of Advanced Industrial Science and Technology (AIST); Tayagaki, Takeshi [National Institute of Advanced Industrial Science and Technology (AIST); Shibata, Hajime [National Institute of Advanced Industrial Science and Technology (AIST); Matsubara, Koji [National Institute of Advanced Industrial Science and Technology (AIST); Niki, Shigeru [National Institute of Advanced Industrial Science and Technology (AIST)

2018-03-02

The precise control of alkali-metal concentrations in Cu(In,Ga)Se2 (CIGS) solar cells via post deposition treatment (PDT) has recently attracted attention. When PDT is performed at an elevated temperature, an accompanying annealing effect is expected. Here, we investigate how thermal annealing affects the redistribution of alkali metals in CIGS solar cells on glass substrates and the properties of the solar cells. In addition, we investigate the origin of non-homogeneous alkali-metal depth profiles that are typical of CIGS grown using a three-stage process. In particular, we use secondary-ion mass spectrometry measurements of the ion concentration as a function of distance from the CIGS surface to investigate the impact of thermal annealing on the distribution of alkali metals (Na, Ka, and Rb) and constituent elements (Ga and In) in the CIGS absorbers. We find that the depth profiles of the alkali metals strongly reflect the density of sites that tend to accommodate alkali metals, i.e., vacancies. Annealing at elevated temperature caused a redistribution of the alkali metals. The thermal-diffusion kinetics of alkali metals depends strongly on the species involved. We introduced low flux potassium fluoride (KF) to study a side effect of KF-PDT, i.e., Na removal from CIGS, separately from its predominant effects such as surface modification. When sufficient amounts of Na are supplied from the soda lime glass via annealing at an elevated temperature, the negative effect was not apparent. Conversely, when the Na supply was not sufficient, it caused a deterioration of the photovoltaic properties.

High Performance Concrete

Directory of Open Access Journals (Sweden)

Traian Oneţ

2009-01-01

Full Text Available The paper presents the last studies and researches accomplished in Cluj-Napoca related to high performance concrete, high strength concrete and self compacting concrete. The purpose of this paper is to raid upon the advantages and inconveniences when a particular concrete type is used. Two concrete recipes are presented, namely for the concrete used in rigid pavement for roads and another one for self-compacting concrete.

HPTA: High-Performance Text Analytics

OpenAIRE

Vandierendonck, Hans; Murphy, Karen; Arif, Mahwish; Nikolopoulos, Dimitrios S.

2017-01-01

One of the main targets of data analytics is unstructured data, which primarily involves textual data. High-performance processing of textual data is non-trivial. We present the HPTA library for high-performance text analytics. The library helps programmers to map textual data to a dense numeric representation, which can be handled more efficiently. HPTA encapsulates three performance optimizations: (i) efficient memory management for textual data, (ii) parallel computation on associative dat...

Pressurized planar electrochromatography, high-performance thin-layer chromatography and high-performance liquid chromatography--comparison of performance.

Science.gov (United States)

Płocharz, Paweł; Klimek-Turek, Anna; Dzido, Tadeusz H

2010-07-16

Kinetic performance, measured by plate height, of High-Performance Thin-Layer Chromatography (HPTLC), High-Performance Liquid Chromatography (HPLC) and Pressurized Planar Electrochromatography (PPEC) was compared for the systems with adsorbent of the HPTLC RP18W plate from Merck as the stationary phase and the mobile phase composed of acetonitrile and buffer solution. The HPLC column was packed with the adsorbent, which was scrapped from the chromatographic plate mentioned. An additional HPLC column was also packed with adsorbent of 5 microm particle diameter, C18 type silica based (LiChrosorb RP-18 from Merck). The dependence of plate height of both HPLC and PPEC separating systems on flow velocity of the mobile phase and on migration distance of the mobile phase in TLC system was presented applying test solute (prednisolone succinate). The highest performance, amongst systems investigated, was obtained for the PPEC system. The separation efficiency of the systems investigated in the paper was additionally confirmed by the separation of test component mixture composed of six hormones. 2010 Elsevier B.V. All rights reserved.

High Performance Computing in Science and Engineering '15 : Transactions of the High Performance Computing Center

CERN Document Server

Kröner, Dietmar; Resch, Michael

2016-01-01

This book presents the state-of-the-art in supercomputer simulation. It includes the latest findings from leading researchers using systems from the High Performance Computing Center Stuttgart (HLRS) in 2015. The reports cover all fields of computational science and engineering ranging from CFD to computational physics and from chemistry to computer science with a special emphasis on industrially relevant applications. Presenting findings of one of Europe’s leading systems, this volume covers a wide variety of applications that deliver a high level of sustained performance. The book covers the main methods in high-performance computing. Its outstanding results in achieving the best performance for production codes are of particular interest for both scientists and engineers. The book comes with a wealth of color illustrations and tables of results.

High Performance Computing in Science and Engineering '17 : Transactions of the High Performance Computing Center

CERN Document Server

Kröner, Dietmar; Resch, Michael; HLRS 2017

2018-01-01

This book presents the state-of-the-art in supercomputer simulation. It includes the latest findings from leading researchers using systems from the High Performance Computing Center Stuttgart (HLRS) in 2017. The reports cover all fields of computational science and engineering ranging from CFD to computational physics and from chemistry to computer science with a special emphasis on industrially relevant applications. Presenting findings of one of Europe’s leading systems, this volume covers a wide variety of applications that deliver a high level of sustained performance.The book covers the main methods in high-performance computing. Its outstanding results in achieving the best performance for production codes are of particular interest for both scientists and engineers. The book comes with a wealth of color illustrations and tables of results.

High-Performance Operating Systems

DEFF Research Database (Denmark)

Sharp, Robin

1999-01-01

Notes prepared for the DTU course 49421 "High Performance Operating Systems". The notes deal with quantitative and qualitative techniques for use in the design and evaluation of operating systems in computer systems for which performance is an important parameter, such as real-time applications......, communication systems and multimedia systems....

Characterization of high quality Cu(In,Ga)Se{sub 2} thin films prepared by rf-magnetron sputtering

Energy Technology Data Exchange (ETDEWEB)

Bouchama, Idris [Departement d' Electronique, Faculte de Technologie, Universite de Msila (Algeria); Djessas, Kamal [Laboratoire Procedes Materiaux et Energie Solaire, PROMES-CNRS, Rambla de la Thermodynamique, Technosud, 66100 Perpignan (France); Bouloufa, Abdeslam [Laboratoire d' Electrochimie et Materiaux, Universite Ferhat Abbas de Setif (Algeria); Gauffier, Jean-Luc [Departement de Physique, INSA de Toulouse, 135, Avenue de Rangueil, 31077 Toulouse Cedex 4 (France)

2013-01-15

This paper reports the production of high quality polycrystalline thin layers of CuIn{sub 0.7}Ga{sub 0.3}Se{sub 2} (CIGS), using rf-magnetron sputtering, from a powder target. These films are designed to be used as absorbers in solar cells. The depositions were carried out at substrate temperatures below 250 C and glass substrates was used. The influence of the substrate temperatures on the crystalline quality as well as structural, optical and electrical properties of thin layers obtained has been studied. X-ray diffraction showed that the films were highly orientated in the (112) and/or (204)/(220) direction. In{sub 2}Se{sub 3} secondary phase was observed on the samples grown at lower substrate temperatures. The surface morphology of CIGS layers studied by Atomic Force Microscopy (AFM) and Scanning Electronic Microscopy (SEM) has been also discussed. The most surprising and exciting outcome of this study was that the as grown films were of near stoichiometric composition. Resistivity measurements were carried out using the four point probe method. The optical absorption showed that energy gap values are between 1.13 and 1.18 eV and rather sharp absorption fronts. Thin film resistivities are between 10.7 and 60.9 {Omega}.cm depending on the experimental growth conditions (copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Enjoyment and other reasons for electronic cigarette use: Results from college students in New York.

Science.gov (United States)

Saddleson, M L; Kozlowski, L T; Giovino, G A; Goniewicz, M L; Mahoney, M C; Homish, G G; Arora, A

2016-03-01

Young people are more likely to have experimented with e-cigarettes (e-cigs) compared with older adults. Few studies identify reasons for experimentation/use of e-cigs among young people; we sought to discover what drives college students to use e-cigs. Undergraduate students (ages 18-23) at four universities in New York State were surveyed. Among e-cig ever users (n=429), reasons for use were examined. A multinomial logistic regression model analyzed the relative risk of reasons for using e-cigs among discontinued, current non-daily and current daily e-cig users. Using e-cigs for enjoyment was associated with current non-daily (RR=2.11, 95% CI=1.18-3.75) and current daily use (RR=19.1, 95% CI=3.71-98.54). Non-daily use was related to use because e-cigs are less toxic than cigarettes (RR=2.80, 95% CI=1.75-4.50). More daily users reported use to quit smoking compared with either non-daily or discontinued users (53.3% vs. 12.2% and 13.3%, respectively; preason. The exception was daily e-cig users, who often reported use for quitting/reduction of smoking. Rather, college students report usage reasons related to affect (e.g. enjoyment). Overall, enjoyment was reported more often than was use for quitting smoking; affective reasons likely play a role in the popularity of e-cigs and should be considered in future assessments of e-cig users. Copyright © 2015 Elsevier Ltd. All rights reserved.

Electronic Cigarette Awareness, Use, and Perceptions among Cancer Patients

Directory of Open Access Journals (Sweden)

Erin J. Buczek MD

2018-05-01

Full Text Available Objective Electronic cigarettes (e-cigs are an emerging trend, yet little is known about their use in the cancer population. The objectives of this study were (1 to describe characteristics of e-cig use among cancer patients, (2 to define e-cig advertising exposure, and (3 to characterize perceptions of traditional cigarettes versus e-cigs. Study Design Cross-sectional study. Setting Comprehensive cancer center. Subjects and Methods Inpatient, current smokers with a cancer diagnosis. E-cig exposure and use were defined using descriptive statistics. Wilcoxon rank test was used to compare perceptions between e-cigs and traditional cigarettes. Results A total of 979 patients were enrolled in the study; 39 cancer patients were identified. Most cancer patients were women (59%, with an average age of 53.3 years. Of the patients, 46.2% reported e-cig use, most of which (88.9% was “experimental or occasional.” The primary reason for e-cig use was to aid smoking cessation (66.7%, alternative use in nonsmoking areas (22.2%, and “less risky” cigarette replacement (5.6%. The most common sources for e-cig information were TV (76.9%, stores (48.7%, friends (35.9%, family (30.8%, and newspapers or magazines (12.8%. Compared with cigarettes, e-cigs were viewed as posing a reduced health risk ( P < .001 and conferring a less negative social impression ( P < .001. They were also viewed as less likely to satisfy nicotine cravings ( P = .002, to relieve boredom ( P = .0005, to have a calming effect ( P < .001, and as tasting pleasant ( P = .006 Conclusions E-cig use and advertising exposure are common among cancer patients. E-cig use is perceived as healthier and more socially acceptable but less likely to produce a number of desired consequences of cigarette use.

Effects of nicotine versus placebo e-cigarette use on symptom relief during initial tobacco abstinence.

Science.gov (United States)

Perkins, Kenneth A; Karelitz, Joshua L; Michael, Valerie C

2017-08-01

Because electronic cigarettes (e-cigs) containing nicotine may relieve smoking abstinence symptoms similar to nicotine replacement therapy medication, we used within-subjects designs to test these effects with a first-generation e-cig in nonquitting and quitting smokers. In Study 1, 28 nontreatment-seeking smokers abstained overnight prior to each of 3 sessions. Minnesota Nicotine Withdrawal Scale (MNWS) withdrawal (and craving item) relief was assessed following 4 exposures (each 10 puffs) over 2 hr to e-cigs that either did (36 mg/ml) or did not (i.e., placebo, 0 mg/ml) contain nicotine or after no e-cig. Relief was greater after nicotine versus placebo e-cig (p < .05) but not after placebo versus no e-cig, showing relief was due to nicotine per se and not simple e-cig use behavior. Using a crossover design in Study 2, smokers preparing to quit soon engaged in 2 experimental 4-day quit periods on separate weeks. In weeks 1 and 3, all received a nicotine or placebo e-cig on Monday to use ad libitum while trying to abstain from smoking on Tuesday through Friday. (Week 2 involved resumption of ad libitum smoking.) MNWS and Questionnaire of Smoking Urges (QSU) craving were assessed at daily visits following 24-hr abstinence. Of 17 enrolled, 12 quit for ≥24 hr at least once, allowing test of relief because of e-cig use on quit days. Withdrawal and craving were reduced because of nicotine versus placebo e-cig use (both p < .05). In sum, compared with placebo e-cigs, nicotine e-cigs can relieve smoking abstinence symptoms, perhaps in a manner similar to Food and Drug Administration-approved nicotine replacement therapy products, although much more research with larger samples is needed. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

High performance fuel technology development

Energy Technology Data Exchange (ETDEWEB)

Koon, Yang Hyun; Kim, Keon Sik; Park, Jeong Yong; Yang, Yong Sik; In, Wang Kee; Kim, Hyung Kyu [KAERI, Daejeon (Korea, Republic of)

2012-01-15

{omicron} Development of High Plasticity and Annular Pellet - Development of strong candidates of ultra high burn-up fuel pellets for a PCI remedy - Development of fabrication technology of annular fuel pellet {omicron} Development of High Performance Cladding Materials - Irradiation test of HANA claddings in Halden research reactor and the evaluation of the in-pile performance - Development of the final candidates for the next generation cladding materials. - Development of the manufacturing technology for the dual-cooled fuel cladding tubes. {omicron} Irradiated Fuel Performance Evaluation Technology Development - Development of performance analysis code system for the dual-cooled fuel - Development of fuel performance-proving technology {omicron} Feasibility Studies on Dual-Cooled Annular Fuel Core - Analysis on the property of a reactor core with dual-cooled fuel - Feasibility evaluation on the dual-cooled fuel core {omicron} Development of Design Technology for Dual-Cooled Fuel Structure - Definition of technical issues and invention of concept for dual-cooled fuel structure - Basic design and development of main structure components for dual- cooled fuel - Basic design of a dual-cooled fuel rod.

High performance homes

DEFF Research Database (Denmark)

Beim, Anne; Vibæk, Kasper Sánchez

2014-01-01

. Consideration of all these factors is a precondition for a truly integrated practice and as this chapter demonstrates, innovative project delivery methods founded on the manufacturing of prefabricated buildings contribute to the production of high performance homes that are cost effective to construct, energy...

Performance of Photovoltaic Modules of Different Solar Cells

Directory of Open Access Journals (Sweden)

Ankita Gaur

2013-01-01

Full Text Available In this paper, an attempt of performance evaluation of semitransparent and opaque photovoltaic (PV modules of different generation solar cells, having the maximum efficiencies reported in the literature at standard test conditions (STC, has been carried out particularly for the months of January and June. The outdoor performance is also evaluated for the commercially available semitransparent and opaque PV modules. Annual electrical energy, capitalized cost, annualized uniform cost (unacost, and cost per unit electrical energy for both types of solar modules, namely, semitransparent and opaque have also been computed along with their characteristics curves. Semitransparent PV modules have shown higher efficiencies compared to the opaque ones. Calculations show that for the PV modules made in laboratory, CdTe exhibits the maximum annual electrical energy generation resulting into minimum cost per unit electrical energy, whereas a-Si/nc-Si possesses the maximum annual electrical energy generation giving minimum cost per unit electrical energy when commercially available solar modules are concerned. CIGS has shown the lowest capitalized cost over all other PV technologies.

Strategy Guideline: High Performance Residential Lighting

Energy Technology Data Exchange (ETDEWEB)

Holton, J.

2012-02-01

The Strategy Guideline: High Performance Residential Lighting has been developed to provide a tool for the understanding and application of high performance lighting in the home. The high performance lighting strategies featured in this guide are drawn from recent advances in commercial lighting for application to typical spaces found in residential buildings. This guide offers strategies to greatly reduce lighting energy use through the application of high quality fluorescent and light emitting diode (LED) technologies. It is important to note that these strategies not only save energy in the home but also serve to satisfy the homeowner's expectations for high quality lighting.

High performance conductometry

International Nuclear Information System (INIS)

Saha, B.

2000-01-01

Inexpensive but high performance systems have emerged progressively for basic and applied measurements in physical and analytical chemistry on one hand, and for on-line monitoring and leak detection in plants and facilities on the other. Salient features of the developments will be presented with specific examples

Improved growth of solution-deposited thin films on polycrystalline Cu(In,Ga)Se{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Witte, Wolfram; Hariskos, Dimitrios [Zentrum fuer Sonnenenergie- und Wasserstoff-Forschung Baden-Wuerttemberg (ZSW), 70565, Stuttgart (Germany); Abou-Ras, Daniel [Helmholtz-Zentrum Berlin fuer Materialien und Energie, 14109, Berlin (Germany)

2016-04-15

CdS and Zn(O,S) grown by chemical bath deposition (CBD) are well established buffer materials for Cu(In,Ga)Se{sub 2} (CIGS) solar cells. As recently reported, a non-contiguous coverage of CBD buffers on CIGS grains with {112} surfaces can be detected, which was explained in terms of low surface energies of the {112} facets, leading to deteriorated wetting of the chemical solution on the CIGS surface. In the present contribution, we report on the effect of air annealing of CIGS thin films prior to the CBD of CdS and Zn(O,S) layers. In contrast to the growth on the as-grown CIGS layers, these buffer lay- ers grow densely on the annealed CIGS layer, even on grains with {112} surfaces. We explain the different growth behavior by increased surface energies of CIGS grains due to the annealing step, i.e., due to oxidation of the CIGS surface. Reference solar cells were processed and completed by i-ZnO/ZnO:Al layers for CdS and by (Zn,Mg)O/ZnO:Al for Zn(O,S) buffers. For solar cells with both, CdS and Zn(O,S) buffers, air-annealed CIGS films with improved buffer coverage resulted in higher power-conversion efficiencies, as compared with the devices containing as-grown CIGS layers. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Mg-doped ZnO thin films deposited by the atomic layer chemical vapor deposition for the buffer layer of CIGS solar cell

Energy Technology Data Exchange (ETDEWEB)

Li, Zhao-Hui [Department of Electronics Engineering, Gachon University, Soojung-gu, Seongnam city 461-701, Gyunggi-do (Korea, Republic of); Center for Photovoltaic and Solar Energy, Shenzhen Institutes of Advanced Technology, Chinese Academy of Sciences, Shenzhen city 518055 (China); Cho, Eou-Sik [Department of Electronics Engineering, Gachon University, Soojung-gu, Seongnam city 461-701, Gyunggi-do (Korea, Republic of); Kwon, Sang Jik, E-mail: sjkwon@gachon.ac.kr [Department of Electronics Engineering, Gachon University, Soojung-gu, Seongnam city 461-701, Gyunggi-do (Korea, Republic of)

2014-09-30

Highlights: • Mg-doped ZnO film as CIGS buffer was prepared by ALD process. • The grain size of ZnO-like hexagonal phase decreased with Mg content. • The transmittance and crystallinity increased but the band gap decreased with temperature. - Abstract: Mg-doped ZnO [(Zn, Mg)O] thin films were prepared by atomic layer chemical vapor deposition (ALCVD) process with different Mg content, using diethyl zinc, biscyclopentadienyl magnesium, and water as the metal and oxygen sources, respectively. The ratio of Mg to Zn was varied by changing the pulse ratio of MgCp{sub 2} to DEZn precursor to study its effect on the properties of (Zn, Mg)O thin films. From the experimental results, it was shown that the grain size of the ZnO-like hexagonal phase (Zn, Mg)O decreased as the Mg content increased. But the transmittance and optical band gap of (Zn, Mg)O films increased with the increase of the Mg content. In addition, the effect of the substrate temperature on the properties of (Zn, Mg)O films was also investigated. The deposition rate, transmittance, and crystallinity of (Zn, Mg)O films increased as the substrate temperature increased. But its band gap decreased slightly with the increase of substrate temperature.

INL High Performance Building Strategy

Energy Technology Data Exchange (ETDEWEB)

Jennifer D. Morton

2010-02-01

High performance buildings, also known as sustainable buildings and green buildings, are resource efficient structures that minimize the impact on the environment by using less energy and water, reduce solid waste and pollutants, and limit the depletion of natural resources while also providing a thermally and visually comfortable working environment that increases productivity for building occupants. As Idaho National Laboratory (INL) becomes the nation’s premier nuclear energy research laboratory, the physical infrastructure will be established to help accomplish this mission. This infrastructure, particularly the buildings, should incorporate high performance sustainable design features in order to be environmentally responsible and reflect an image of progressiveness and innovation to the public and prospective employees. Additionally, INL is a large consumer of energy that contributes to both carbon emissions and resource inefficiency. In the current climate of rising energy prices and political pressure for carbon reduction, this guide will help new construction project teams to design facilities that are sustainable and reduce energy costs, thereby reducing carbon emissions. With these concerns in mind, the recommendations described in the INL High Performance Building Strategy (previously called the INL Green Building Strategy) are intended to form the INL foundation for high performance building standards. This revised strategy incorporates the latest federal and DOE orders (Executive Order [EO] 13514, “Federal Leadership in Environmental, Energy, and Economic Performance” [2009], EO 13423, “Strengthening Federal Environmental, Energy, and Transportation Management” [2007], and DOE Order 430.2B, “Departmental Energy, Renewable Energy, and Transportation Management” [2008]), the latest guidelines, trends, and observations in high performance building construction, and the latest changes to the Leadership in Energy and Environmental Design

High Performance Networks for High Impact Science

Energy Technology Data Exchange (ETDEWEB)

Scott, Mary A.; Bair, Raymond A.

2003-02-13

This workshop was the first major activity in developing a strategic plan for high-performance networking in the Office of Science. Held August 13 through 15, 2002, it brought together a selection of end users, especially representing the emerging, high-visibility initiatives, and network visionaries to identify opportunities and begin defining the path forward.

High performance fuel technology development : Development of high performance cladding materials

International Nuclear Information System (INIS)

Park, Jeongyong; Jeong, Y. H.; Park, S. Y.

2012-04-01

The superior in-pile performance of the HANA claddings have been verified by the successful irradiation test and in the Halden research reactor up to the high burn-up of 67GWD/MTU. The in-pile corrosion and creep resistances of HANA claddings were improved by 40% and 50%, respectively, over Zircaloy-4. HANA claddings have been also irradiated in the commercial reactor up to 2 reactor cycles, showing the corrosion resistance 40% better than that of ZIRLO in the same fuel assembly. Long-term out-of-pile performance tests for the candidates of the next generation cladding materials have produced the highly reliable test results. The final candidate alloys were selected and they showed the corrosion resistance 50% better than the foreign advanced claddings, which is beyond the original target. The LOCA-related properties were also improved by 20% over the foreign advanced claddings. In order to establish the optimal manufacturing process for the inner and outer claddings of the dual-cooled fuel, 18 different kinds of specimens were fabricated with various cold working and annealing conditions. Based on the performance tests and various out-of-pile test results obtained from the specimens, the optimal manufacturing process was established for the inner and outer cladding tubes of the dual-cooled fuel

Photoelectrochemical water splitting using a Cu(In,Ga)Se{sub 2} thin film

Energy Technology Data Exchange (ETDEWEB)

Yokoyama, Daisuke; Minegishi, Tsutomu; Maeda, Kazuhiko; Katayama, Masao; Kubota, Jun; Domen, Kazunari [Department of Chemical System Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Yamada, Akira; Konagai, Makoto [Department of Physical Electronics, Graduate School of Engineering, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo 152-8550 (Japan)

2010-06-15

The effects of surface modification and reaction conditions on the photoelectrochemical properties of polycrystalline Cu(In,Ga)Se{sub 2} (CIGS) thin films for water splitting were studied. CIGS modified with platinum particles (Pt/CIGS) generated a cathodic photocurrent at potentials up to + 0.4 V vs. RHE at pH = 9.5. The photocurrent was stable for 16 h, which resulted in a turnover number of over 500. A CdS-inserted film (Pt/CdS/CIGS) had significantly improved properties compared to Pt/CIGS: a 0.3 V higher onset potential of cathodic photocurrent and a three-fold increase in the quantum efficiency. Our results suggest the feasibility of CIGS as a photocathode for biphotoelectrochemical water splitting. (author)

Carbon nanomaterials for high-performance supercapacitors

OpenAIRE

Tao Chen; Liming Dai

2013-01-01

Owing to their high energy density and power density, supercapacitors exhibit great potential as high-performance energy sources for advanced technologies. Recently, carbon nanomaterials (especially, carbon nanotubes and graphene) have been widely investigated as effective electrodes in supercapacitors due to their high specific surface area, excellent electrical and mechanical properties. This article summarizes the recent progresses on the development of high-performance supercapacitors bas...

Clojure high performance programming

CERN Document Server

Kumar, Shantanu

2013-01-01

This is a short, practical guide that will teach you everything you need to know to start writing high performance Clojure code.This book is ideal for intermediate Clojure developers who are looking to get a good grip on how to achieve optimum performance. You should already have some experience with Clojure and it would help if you already know a little bit of Java. Knowledge of performance analysis and engineering is not required. For hands-on practice, you should have access to Clojure REPL with Leiningen.

Real time spectroscopic ellipsometry for analysis and control of thin film polycrystalline semiconductor deposition in photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Koirala, Prakash; Attygalle, Dinesh; Aryal, Puruswottam; Pradhan, Puja; Chen, Jie [Center for Photovoltaics Innovation and Commercialization and Department of Physics and Astronomy, University of Toledo, Toledo, OH 43606 (United States); Marsillac, Sylvain [Department of Electrical and Computer Engineering, Old Dominion University, Norfolk, VA 23529 (United States); Ferlauto, Andre S.; Podraza, Nikolas J.; Collins, Robert W. [Center for Photovoltaics Innovation and Commercialization and Department of Physics and Astronomy, University of Toledo, Toledo, OH 43606 (United States)

2014-11-28

Real time spectroscopic ellipsometry (RTSE) from the near-infrared to ultraviolet has been applied for analysis of the deposition of polycrystalline thin films that form the basis of two key photovoltaic heterojunction configurations, superstrate SnO{sub 2}/CdS/CdTe and substrate Mo/Cu(In{sub 1−x}Ga{sub x})Se{sub 2}/CdS. The focus of this work is to develop capabilities for monitoring and controlling the key steps in the fabrication of these device structures. Analysis of RTSE data collected during sputter deposition of CdS on a rough SnO{sub 2} transparent top contact provides the time evolution of the CdS effective thickness, or film volume per unit substrate area. This thickness includes interface, bulk, and surface roughness layer components and affects the CdS/CdTe heterojunction performance and the quantum efficiency of the solar cell in the blue region of the solar spectrum. Similarly, analysis of RTSE data collected during co-evaporation of Cu(In{sub 1−x}Ga{sub x})Se{sub 2} (CIGS; x ∼ 0.3) on a rough Mo back contact provides the evolution of a second phase of Cu{sub 2−x}Se within the CIGS layer. During the last stage of CIGS deposition, the In, Ga, and Se co-evaporants convert this Cu{sub 2−x}Se phase to CIGS, and RTSE identifies the endpoint, specifically the time at which complete conversion occurs and single-phase, large-grain CIGS is obtained in this key stage. - Highlights: • Real time spectroscopic ellipsometry (RTSE) study of CdS and CuIn{sub 1−x}Ga{sub x}Se{sub 2} (CIGS) films. • RTSE during CdS deposition provides the evolution of the CdS effective thickness. • RTSE for CIGS film enables to measure and control the composition and thickness. • The work leads to the development of optical models for processing steps.

Delivering high performance BWR fuel reliably

International Nuclear Information System (INIS)

Schardt, J.F.

1998-01-01

Utilities are under intense pressure to reduce their production costs in order to compete in the increasingly deregulated marketplace. They need fuel, which can deliver high performance to meet demanding operating strategies. GE's latest BWR fuel design, GE14, provides that high performance capability. GE's product introduction process assures that this performance will be delivered reliably, with little risk to the utility. (author)

[Focus on electronic cigarettes].

Science.gov (United States)

Tinghino, Biagio; Pacifici, Roberta; Di Pucchio, Alessandra; Palmi, Ilaria; Solimini, Renata; Faggiano, Fabrizio; Gorini, Giuseppe

2013-01-01

There is no clear regulation on electronic cigarettes (e-cig); their health effects are not yet fully investigated and there is insufficient standardisation and quality control of the product. Moreover, the e-cig could be a gateway for young people to nicotine addiction and traditional cigarette smoking. In Italy, the Ministry of Health banned the sale of e-cig with nicotine firstly to adolescents aged marketing of e-cigs, to make them less attractive, to forbid their use in enclosed areas, and prevent them from being promoted. E-cigs, however, seem to be much less dangerous than traditional cigarettes, although the few studies conducted are not sufficient to demonstrate either a clear therapeutic efficacy of e-cig or their total harmlessness. If e-cig had a known content, were made according to clear rules and in certified laboratories, without toxic substances, it could be used to help heavy smokers to quit, or at least to reduce smoking habits. There is a large proportion of smokers who are unable to quit. The revision of the European Directive (the proposal is being evaluated and we are waiting for its final approval) on tobacco recommends free sale for a minority of e-cigs only, those with a nicotine content e-cig and the much more dangerous tobacco cigarettes are still sold without any restriction.

High performance bio-integrated devices

Science.gov (United States)

Kim, Dae-Hyeong; Lee, Jongha; Park, Minjoon

2014-06-01

In recent years, personalized electronics for medical applications, particularly, have attracted much attention with the rise of smartphones because the coupling of such devices and smartphones enables the continuous health-monitoring in patients' daily life. Especially, it is expected that the high performance biomedical electronics integrated with the human body can open new opportunities in the ubiquitous healthcare. However, the mechanical and geometrical constraints inherent in all standard forms of high performance rigid wafer-based electronics raise unique integration challenges with biotic entities. Here, we describe materials and design constructs for high performance skin-mountable bio-integrated electronic devices, which incorporate arrays of single crystalline inorganic nanomembranes. The resulting electronic devices include flexible and stretchable electrophysiology electrodes and sensors coupled with active electronic components. These advances in bio-integrated systems create new directions in the personalized health monitoring and/or human-machine interfaces.

Differential in-depth characterization of co-evaporated Cu(In,Ga)Se{sub 2} thin films for solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Klinkert, Torben; Jubault, Marie; Donsanti, Frédérique; Lincot, Daniel; Guillemoles, Jean-François

2014-05-02

In this paper we report an alternative approach to perform in-depth characterisation of Cu(In,Ga)Se{sub 2} (CIGS) absorber layers. While usually groups stop their co-evaporation process at different points and analyse the precursor or intermediate phases, we perform in-depth analysis on the finished absorber layer as it will be used in the solar cell. A co-evaporated CIGS layer was cut to several samples, which then were chemically etched to different thicknesses. Compared to sputtering ablation techniques, this avoids the selective abrasion of atoms with different binding energies. The samples were analysed by Raman spectroscopy and X-ray diffraction. In-depth information is obtained by differentiating the signals of samples with different thicknesses after etching and a first order correction for absorption losses was executed. The Ga/(Ga + In) ratio extracted from X-ray diffraction measurements is in good agreement with the double gradient observed by glow discharge optical emission spectroscopy. A slight variation might indicate residual stress in the CIGS layer. A preferred (112) orientation across the whole film together with changing (220), (116) and (312) orientation preferences is reported and explained on the basis of the CIGS crystal structure. Raman signals attributed to ordered vacancy compounds are found throughout the whole sample thickness and not only close to the surface, as often reported in the literature. - Highlights: • Co-evaporated CIGS with double Ga gradient was chemically etched to different thicknesses. • X-ray diffractograms were differentiated to gain in-depth information. • (116)-oriented grains are found to tend to grow on (312)-oriented grains. • Change of preferred orientation was linked to crystal structure at grain boundaries. • Ga gradient from Vegard's law of XRD peaks is in agreement with GDOES measurement.

Encapsulated Somatic Embryos and Zygotic Embryos for Obtaining Artificial Seeds of Rauli-Beech (Nothofagus alpina (Poepp. & Endl. Oerst. Encapsulado de Embriones Somáticos y Embriones Cigóticos para Obtención de Semillas Artificiales de Raulí (Nothofagus alpina (Poepp. & Endl. Oerst.

Directory of Open Access Journals (Sweden)

Priscila Cartes R

2009-03-01

Full Text Available Somatic and zygotic embryos from mature seeds of rauli-beech, Nothofagus alpina (Poepp. & Endl. Oerst., were encapsulated in different artificial endosperms in order to generate a cover that fulfills the function of nourishment and protection of the embryos, facilitating their later germination. The content of sodium alginate varied by 4%, 3%, and 2%, as did the immersion time in calcium chloride (CaCl2, which acts as complexing agent. The artificial endosperm components of the Murashige and Skoog medium (MS were added, supplemented with 0.5 mg L-1 indolacetic acid (IAA, 0.5 mg L-1 naphthaleneacetic acid (NAA, 2 mg L-1 6-benzylaminopurine (BAP and 30 g L-1 sucrose. The germinative behaviors of encapsulated somatic and zygotic embryos were evaluated after 4 wk. Comparing the percentages of germination reached by encapsulated somatic and zygotic embryos it was observed that they had similar germinative behavior according to the type of encapsulation applied. However, zygotic embryos substantially exceeded the germination levels reached by somatic embryos, 100% vs. 45% respectively.Embriones somáticos y cigóticos provenientes de semillas maduras de raulí, Nothofagus alpina (Poepp. & Endl. Oerst., se encapsularon en diferentes endospermas sintéticos con el fin de generar una cubierta que cumpla la función de nutrir y proteger al embrión para facilitar su posterior germinación. Se varió el contenido de alginato de sodio al 4%, 3% y 2% y el tiempo de inmersión en cloruro de calcio (CaCl2, el que actúa como agente acomplejante. Además, a la matriz artificial se adicionaron componentes del medio Murashige y Skoog (MS suplementado con: 0,5 mg L-1 de indolacetic acid (IAA, 0,5 mg L-1 de ácido naftalenacético (NAA, 2 mg L-1 de 6-bencilaminopurina (BAP y 30 gL-1 de sacarosa. Al cabo de 4 semanas el porcentaje de germinación de los embriones somáticos y cigóticos encapsulados tuvieron similar comportamiento germinativo según el tipo de

Investigation of the effect of potassium on Cu(In,Ga)Se{sub 2} layers and solar cells

Energy Technology Data Exchange (ETDEWEB)

Laemmle, A., E-mail: anke.laemmle@zsw-bw.de; Wuerz, R.; Powalla, M.

2015-05-01

We investigate the influence of potassium (K) on the Cu(In,Ga)Se{sub 2} (CIGS) growth kinetics on alkali-free alumina substrates and the electrical parameters of the CIGS solar cell by intentional K doping of the CIGS layer by a KF-precursor layer and KF-post deposition treatment (PDT). Secondary ion mass spectroscopy measurements revealed that K can be incorporated into the CIGS layer by both processes. The CIGS composition of the KF-precursor sample shows a stronger [Ga]/([Ga] + [In]) (GGI) profile. By analysing the samples with scanning electron microscopy we observed smaller CIGS grains for the KF-precursor sample compared to the K-free reference and KF-PDT sample. jV-measurements of the KF-PDT and the KF-precursor sample show an increase in the cell efficiency η from 10.7% to 13.6% and 13.7%, respectively, compared to the K-free reference sample. The external quantum efficiency measurements of the KF-precursor sample show an increased absorption in the infrared region. Capacitance-voltage measurements reveal an increase in the net doping concentration of both samples treated with K. We assume that the enhancement is caused by passivation of grain boundaries and donor-like defects by K, as previously demonstrated for Na. - Highlights: • K-doped Cu(In,Ga)Se{sub 2} (CIGS) layers from KF-precursor and KF-post deposition treatment • Separation of the K-effect from the Na-effect by using alkali-free substrates • Interdiffusion of CIGS elements during CIGS growth is hindered by K • KF-precursor leads to smaller CIGS grains and a stronger Cu depletion at the CIGS surface. • K leads to an increase in the conversion efficiency.

High Performance Macromolecular Material

National Research Council Canada - National Science Library

Forest, M

2002-01-01

.... In essence, most commercial high-performance polymers are processed through fiber spinning, following Nature and spider silk, which is still pound-for-pound the toughest liquid crystalline polymer...

Self-assembled synthesis of 3D Cu(In1 − xGax)Se2 nanoarrays by one-step electroless deposition into ordered AAO template

International Nuclear Information System (INIS)

Zhang, Bin; Zheng, Maojun; Xiong, Zuzhou; Zhu, Changqing; Li, Hong; Wang, Faze; Shen, Wenzhong; Zhou, Tao; Ma, Li

2014-01-01

Quaternary nanostructured Cu(In 1 − x Ga x )Se 2 (CIGS) arrays were successfully fabricated via a novel and simple solution-based protocol on the electroless deposition method, using a flexible, highly ordered anodic aluminium oxide (AAO) substrate. This method does not require electric power, complicated sensitization processes, or complexing agents, but provides nearly 100% pore fill factor to AAO templates. The field emission scanning electron microscopy (FE-SEM) images show that we obtained uniformly three-dimensional nanostructured CIGS arrays, and we can tailor the diameter and wall thicknesses of the nanostructure by adjusting the pore diameter of the AAO and metal Mo layer. Their chemical composition was determined by energy-dispersive spectroscopy analysis, which is very close to the stoichiometric value. The Raman spectroscopy, x-ray diffraction (XRD) pattern, and transmission electron microscopy (TEM) further confirm the formation of nanostructured CIGS with prominent chalcopyrite structure. The nanostructured CIGS arrays can support the design of low-cost, highlight-trapping, and enhanced carrier collection nanostructured solar cells. (paper)

Progress in Polycrystalline Thin-Film Cu(In,GaSe2 Solar Cells

Directory of Open Access Journals (Sweden)

Udai P. Singh

2010-01-01

Full Text Available For some time, the chalcopyrite semiconductor CuInSe2 and its alloy with Ga and/or S [Cu(InGaSe2 or Cu(InGa(Se,S2], commonly referred as CIGS, have been leading thin-film material candidates for incorporation in high-efficiency photovoltaic devices. CuInSe2-based solar cells have shown long-term stability and the highest conversion efficiencies among all thin-film solar cells, reaching 20%. A variety of methods have been reported to prepare CIGS thin film. Efficiency of solar cells depends upon the various deposition methods as they control optoelectronic properties of the layers and interfaces. CIGS thin film grown on glass or flexible (metal foil, polyimide substrates require p-type absorber layers of optimum optoelectronic properties and n-type wideband gap partner layers to form the p-n junction. Transparent conducting oxide and specific metal layers are used for front and back contacts. Progress made in the field of CIGS solar cell in recent years has been reviewed.

Delivering high performance BWR fuel reliably

Energy Technology Data Exchange (ETDEWEB)

Schardt, J.F. [GE Nuclear Energy, Wilmington, NC (United States)

1998-07-01

Utilities are under intense pressure to reduce their production costs in order to compete in the increasingly deregulated marketplace. They need fuel, which can deliver high performance to meet demanding operating strategies. GE's latest BWR fuel design, GE14, provides that high performance capability. GE's product introduction process assures that this performance will be delivered reliably, with little risk to the utility. (author)

Carpet Aids Learning in High Performance Schools

Science.gov (United States)

Hurd, Frank

2009-01-01

The Healthy and High Performance Schools Act of 2002 has set specific federal guidelines for school design, and developed a federal/state partnership program to assist local districts in their school planning. According to the Collaborative for High Performance Schools (CHPS), high-performance schools are, among other things, healthy, comfortable,…

High-performance-vehicle technology. [fighter aircraft propulsion

Science.gov (United States)

Povinelli, L. A.

1979-01-01

Propulsion needs of high performance military aircraft are discussed. Inlet performance, nozzle performance and cooling, and afterburner performance are covered. It is concluded that nonaxisymmetric nozzles provide cleaner external lines and enhanced maneuverability, but the internal flows are more complex. Swirl afterburners show promise for enhanced performance in the high altitude, low Mach number region.

Academic performance in high school as factor associated to academic performance in college

Directory of Open Access Journals (Sweden)

Mileidy Salcedo Barragán

2008-12-01

Full Text Available This study intends to find the relationship between academic performance in High School and College, focusing on Natural Sciences and Mathematics. It is a descriptive correlational study, and the variables were academic performance in High School, performance indicators and educational history. The correlations between variables were established with Spearman’s correlation coefficient. Results suggest that there is a positive relationship between academic performance in High School and Educational History, and a very weak relationship between performance in Science and Mathematics in High School and performance in College.

High Performance Grinding and Advanced Cutting Tools

CERN Document Server

Jackson, Mark J

2013-01-01

High Performance Grinding and Advanced Cutting Tools discusses the fundamentals and advances in high performance grinding processes, and provides a complete overview of newly-developing areas in the field. Topics covered are grinding tool formulation and structure, grinding wheel design and conditioning and applications using high performance grinding wheels. Also included are heat treatment strategies for grinding tools, using grinding tools for high speed applications, laser-based and diamond dressing techniques, high-efficiency deep grinding, VIPER grinding, and new grinding wheels.

Investigations of vertical chemical gradients in Cu(In,Ga)S{sub 2}-thin films prepared by sulfurization of sputtered precursor layers using highly spatially resolved cathodoluminescence microscopy

Energy Technology Data Exchange (ETDEWEB)

Ribbe, Stefan; Mueller, Mathias; Bertram, Frank; Hempel, Thomas; Christen, Juergen [Institute for Experimental Physics, Otto-von-Guericke-University Magdeburg (Germany); Rodriguez-Alvarez, Humberto; Lauche, Jakob; Schock, Hans-Werner [Helmholtz Center Berlin for Materials and Energy (Germany)

2012-07-01

The luminescence properties of Cu(In,Ga)S{sub 2}(CIGS)-absorber layers for thin film solar cells have been studied by highly spatially resolved cathodoluminescence (CL) at low temperature (T=5 K). In/Cu-Ga-precursors were annealed with elementary sulfur pellets in a rapid thermal process at different annealing times to represent different growth steps of the CIGS absorber layer. Spatially integral CL spectra show a dominant peak at 825 nm accompanied by a low-energy shoulder at 890 nm. Only a slight blue shift of the main peak is observed by variation of the excitation density. Investigations of cross-sections show for all samples a similar luminescence distribution. Near the molybdenum back contact distinct areas show luminescence emitting at 680-750 nm. In contrast, in upper regions of the layer a homogeneous low-energy luminescence at around 820 nm is observed which exhibits the most intensive spots on the cross-section. In local spectra we observe a change of the dominant recombination channel at the interface of these two regions.

Highlighting High Performance: Whitman Hanson Regional High School; Whitman, Massachusetts

Energy Technology Data Exchange (ETDEWEB)

2006-06-01

This brochure describes the key high-performance building features of the Whitman-Hanson Regional High School. The brochure was paid for by the Massachusetts Technology Collaborative as part of their Green Schools Initiative. High-performance features described are daylighting and energy-efficient lighting, indoor air quality, solar and wind energy, building envelope, heating and cooling systems, water conservation, and acoustics. Energy cost savings are also discussed.

Influence of carrier concentration on the performance of CIAS solar cell

Science.gov (United States)

Patel, Kinjal; Ray, Jaymin

2018-05-01

Photovoltaic research has moved beyond the use of single crystalline materials such as Group IV elemental Si and Group III-V compounds like GaAs to much more complex compounds of the Group I-III-VI2 with chalcopyrite structure. The ternary ABC2 chalcopyrites (A=Cu; B=In, Ga or Al; C= S, Se or Te) form a large group of semiconducting materials with diverse structural and electrical properties. These materials are attractive for thin film photovoltaic application for a number of reasons. The bandgap of CuInSe2 is relatively low, 1.04 eV, but it can be adjusted to better match the solar spectrum either by substituting part of In by Ga or part of Se by S. Most reported and popular Cu(In,Ga)Se2 (CIGS) is one of its derivative. Efficiency of the CIGS devices with Eg >1.3 eV is reduced by the degradation of the electronic properties of the absorber leading to losses in the fill-factor and the open-circuit voltage. Alternatively, the performance can be improved by the addition of Al to form CuInAlSe2 (CIAS) absorber layers with an increase in the bandgap energy, which matches closely with the solar spectrum. In the present work an effort was made in the direction of improving the conversion efficiency by studying the influence of carrier concentration. SCAPS simulation program is used to simulate the CIAS structure numerically. The obtained results intended the significant variation in the values of conversion efficiency. Variation in the efficiency can be considered because of the relation optical absorption and carrier concentration. Observed highest efficiency is 10 %, which can be further improved by considering actual parameters of the device as well as the operating condition.

High performance polymeric foams

International Nuclear Information System (INIS)

Gargiulo, M.; Sorrentino, L.; Iannace, S.

2008-01-01

The aim of this work was to investigate the foamability of high-performance polymers (polyethersulfone, polyphenylsulfone, polyetherimide and polyethylenenaphtalate). Two different methods have been used to prepare the foam samples: high temperature expansion and two-stage batch process. The effects of processing parameters (saturation time and pressure, foaming temperature) on the densities and microcellular structures of these foams were analyzed by using scanning electron microscopy

Electronic cigarette aerosols and copper nanoparticles induce mitochondrial stress and promote DNA fragmentation in lung fibroblasts

Energy Technology Data Exchange (ETDEWEB)

Lerner, Chad A.; Rutagarama, Pierrot; Ahmad, Tanveer; Sundar, Isaac K.; Elder, Alison; Rahman, Irfan, E-mail: irfan_rahman@urmc.rochester.edu

2016-09-02

Oxidants or nanoparticles have recently been identified as constituents of aerosols released from various styles of electronic cigarettes (E-cigs). Cells in the lung may be directly exposed to these constituents and harbor reactive properties capable of incurring acute cell injury. Our results show mitochondria are sensitive to both E-cig aerosols and aerosol containing copper nanoparticles when exposed to human lung fibroblasts (HFL-1) using an Air-Liquid Interface culture system, evident by elevated levels of mitochondrial ROS (mtROS). Increased mtROS after aerosol exposure is associated with reduced stability of OxPhos electron transport chain (ETC) complex IV subunit and nuclear DNA fragmentation. Increased levels of IL-8 and IL-6 in HFL-1 conditioned media were also observed. These findings reveal both mitochondrial, genotoxic, and inflammatory stresses are features of direct cell exposure to E-cig aerosols which are ensued by inflammatory duress, raising a concern on deleterious effect of vaping. - Graphical abstract: Oxidants and possibly reactive properties of metal particles in E-cig aerosols impart mitochondrial oxidative stress and DNA damage. These biological effects accompany inflammatory response which may raise concern regarding long term E-cig use. Mitochondria may be particularly sensitive to reactive properties of E-cig aerosols in addition to the potential for them to induce genotoxic stress by generating increased ROS. - Highlights: • Mitochondria are sensitive to both E-cig aerosols and metal nanoparticles. • Increased mtROS by E-cig aerosol is associated with disrupted mitochondrial energy. • E-cig causes nuclear DNA fragmentation. • E-cig aerosols induce pro-inflammatory response in human fibroblasts.

Will chronic e-cigarette use cause lung disease?

Science.gov (United States)

Rowell, Temperance R; Tarran, Robert

2015-12-15

Chronic tobacco smoking is a major cause of preventable morbidity and mortality worldwide. In the lung, tobacco smoking increases the risk of lung cancer, and also causes chronic obstructive pulmonary disease (COPD), which encompasses both emphysema and chronic bronchitis. E-cigarettes (E-Cigs), or electronic nicotine delivery systems, were developed over a decade ago and are designed to deliver nicotine without combusting tobacco. Although tobacco smoking has declined since the 1950s, E-Cig usage has increased, attracting both former tobacco smokers and never smokers. E-Cig liquids (e-liquids) contain nicotine in a glycerol/propylene glycol vehicle with flavorings, which are vaporized and inhaled. To date, neither E-Cig devices, nor e-liquids, are regulated by the Food and Drug Administration (FDA). The FDA has proposed a deeming rule, which aims to initiate legislation to regulate E-Cigs, but the timeline to take effect is uncertain. Proponents of E-Cigs say that they are safe and should not be regulated. Opposition is varied, with some opponents proposing that E-Cig usage will introduce a new generation to nicotine addiction, reversing the decline seen with tobacco smoking, or that E-Cigs generally may not be safe and will trigger diseases like tobacco. In this review, we shall discuss what is known about the effects of E-Cigs on the mammalian lung and isolated lung cells in vitro. We hope that collating this data will help illustrate gaps in the knowledge of this burgeoning field, directing researchers toward answering whether or not E-Cigs are capable of causing disease. Copyright © 2015 the American Physiological Society.

Electronic cigarette aerosols and copper nanoparticles induce mitochondrial stress and promote DNA fragmentation in lung fibroblasts

International Nuclear Information System (INIS)

Lerner, Chad A.; Rutagarama, Pierrot; Ahmad, Tanveer; Sundar, Isaac K.; Elder, Alison; Rahman, Irfan

2016-01-01

Oxidants or nanoparticles have recently been identified as constituents of aerosols released from various styles of electronic cigarettes (E-cigs). Cells in the lung may be directly exposed to these constituents and harbor reactive properties capable of incurring acute cell injury. Our results show mitochondria are sensitive to both E-cig aerosols and aerosol containing copper nanoparticles when exposed to human lung fibroblasts (HFL-1) using an Air-Liquid Interface culture system, evident by elevated levels of mitochondrial ROS (mtROS). Increased mtROS after aerosol exposure is associated with reduced stability of OxPhos electron transport chain (ETC) complex IV subunit and nuclear DNA fragmentation. Increased levels of IL-8 and IL-6 in HFL-1 conditioned media were also observed. These findings reveal both mitochondrial, genotoxic, and inflammatory stresses are features of direct cell exposure to E-cig aerosols which are ensued by inflammatory duress, raising a concern on deleterious effect of vaping. - Graphical abstract: Oxidants and possibly reactive properties of metal particles in E-cig aerosols impart mitochondrial oxidative stress and DNA damage. These biological effects accompany inflammatory response which may raise concern regarding long term E-cig use. Mitochondria may be particularly sensitive to reactive properties of E-cig aerosols in addition to the potential for them to induce genotoxic stress by generating increased ROS. - Highlights: • Mitochondria are sensitive to both E-cig aerosols and metal nanoparticles. • Increased mtROS by E-cig aerosol is associated with disrupted mitochondrial energy. • E-cig causes nuclear DNA fragmentation. • E-cig aerosols induce pro-inflammatory response in human fibroblasts.

Responsive design high performance

CERN Document Server

Els, Dewald

2015-01-01

This book is ideal for developers who have experience in developing websites or possess minor knowledge of how responsive websites work. No experience of high-level website development or performance tweaking is required.

Investigating the electronic properties of Al{sub 2}O{sub 3}/Cu(In,Ga)Se{sub 2} interface

Energy Technology Data Exchange (ETDEWEB)

Kotipalli, R., E-mail: raja.kotipalli@uclouvain.be; Rajkumar, R.; Flandre, D. [ICTEAM, Université catholique de Louvain, Louvain-la-Neuve, 1348 (Belgium); Vermang, B., E-mail: bart.vermang@imec.be [Ångström Solar Center, University of Uppsala, Uppsala, 75121 (Sweden); ESAT-KU Leuven, University of Leuven, Leuven, 3001 (Belgium); IMEC, Kapeldreef 75, Leuven, 3001 (Belgium); Joel, J.; Edoff, M. [Ångström Solar Center, University of Uppsala, Uppsala, 75121 (Sweden)

2015-10-15

Atomic layer deposited (ALD) Al{sub 2}O{sub 3} films on Cu(In,Ga)Se{sub 2} (CIGS) surfaces have been demonstrated to exhibit excellent surface passivation properties, which is advantageous in reducing recombination losses at the rear metal contact of CIGS thin-film solar cells. Here, we report, for the first time, experimentally extracted electronic parameters, i.e. fixed charge density (Q{sub f}) and interface-trap charge density (D{sub it}), for as-deposited (AD) and post-deposition annealed (PDA) ALD Al{sub 2}O{sub 3} films on CIGS surfaces using capacitance–voltage (C-V) and conductance-frequency (G-f) measurements. These results indicate that the AD films exhibit positive fixed charges Q{sub f} (approximately 10{sup 12} cm{sup −2}), whereas the PDA films exhibit a very high density of negative fixed charges Q{sub f} (approximately 10{sup 13} cm{sup −2}). The extracted D{sub it} values, which reflect the extent of chemical passivation, were found to be in a similar range of order (approximately 10{sup 12} cm{sup −2} eV{sup −1}) for both AD and PDA samples. The high density of negative Q{sub f} in the bulk of the PDA Al{sub 2}O{sub 3} film exerts a strong Coulomb repulsive force on the underlying CIGS minority carriers (n{sub s}), preventing them to recombine at the CIGS/Al{sub 2}O{sub 3} interface. Using experimentally extracted Q{sub f} and D{sub it} values, SCAPS simulation results showed that the surface concentration of minority carriers (n{sub s}) in the PDA films was approximately eight-orders of magnitude lower than in the AD films. The electrical characterization and estimations presented in this letter construct a comprehensive picture of the interfacial physics involved at the Al{sub 2}O{sub 3}/CIGS interface.

France's State of the Art Distributed Optical Fibre Sensors Qualified for the Monitoring of the French Underground Repository for High Level and Intermediate Level Long Lived Radioactive Wastes.

Science.gov (United States)

Delepine-Lesoille, Sylvie; Girard, Sylvain; Landolt, Marcel; Bertrand, Johan; Planes, Isabelle; Boukenter, Aziz; Marin, Emmanuel; Humbert, Georges; Leparmentier, Stéphanie; Auguste, Jean-Louis; Ouerdane, Youcef

2017-06-13

This paper presents the state of the art distributed sensing systems, based on optical fibres, developed and qualified for the French Cigéo project, the underground repository for high level and intermediate level long-lived radioactive wastes. Four main parameters, namely strain, temperature, radiation and hydrogen concentration are currently investigated by optical fibre sensors, as well as the tolerances of selected technologies to the unique constraints of the Cigéo's severe environment. Using fluorine-doped silica optical fibre surrounded by a carbon layer and polyimide coating, it is possible to exploit its Raman, Brillouin and Rayleigh scattering signatures to achieve the distributed sensing of the temperature and the strain inside the repository cells of radioactive wastes. Regarding the dose measurement, promising solutions are proposed based on Radiation Induced Attenuation (RIA) responses of sensitive fibres such as the P-doped ones. While for hydrogen measurements, the potential of specialty optical fibres with Pd particles embedded in their silica matrix is currently studied for this gas monitoring through its impact on the fibre Brillouin signature evolution.

Striving for Excellence Sometimes Hinders High Achievers: Performance-Approach Goals Deplete Arithmetical Performance in Students with High Working Memory Capacity

Science.gov (United States)

Crouzevialle, Marie; Smeding, Annique; Butera, Fabrizio

2015-01-01

We tested whether the goal to attain normative superiority over other students, referred to as performance-approach goals, is particularly distractive for high-Working Memory Capacity (WMC) students—that is, those who are used to being high achievers. Indeed, WMC is positively related to high-order cognitive performance and academic success, a record of success that confers benefits on high-WMC as compared to low-WMC students. We tested whether such benefits may turn out to be a burden under performance-approach goal pursuit. Indeed, for high achievers, aiming to rise above others may represent an opportunity to reaffirm their positive status—a stake susceptible to trigger disruptive outcome concerns that interfere with task processing. Results revealed that with performance-approach goals—as compared to goals with no emphasis on social comparison—the higher the students’ WMC, the lower their performance at a complex arithmetic task (Experiment 1). Crucially, this pattern appeared to be driven by uncertainty regarding the chances to outclass others (Experiment 2). Moreover, an accessibility measure suggested the mediational role played by status-related concerns in the observed disruption of performance. We discuss why high-stake situations can paradoxically lead high-achievers to sub-optimally perform when high-order cognitive performance is at play. PMID:26407097

High-performance ceramics. Fabrication, structure, properties

International Nuclear Information System (INIS)

Petzow, G.; Tobolski, J.; Telle, R.

1996-01-01

The program ''Ceramic High-performance Materials'' pursued the objective to understand the chaining of cause and effect in the development of high-performance ceramics. This chain of problems begins with the chemical reactions for the production of powders, comprises the characterization, processing, shaping and compacting of powders, structural optimization, heat treatment, production and finishing, and leads to issues of materials testing and of a design appropriate to the material. The program ''Ceramic High-performance Materials'' has resulted in contributions to the understanding of fundamental interrelationships in terms of materials science, which are summarized in the present volume - broken down into eight special aspects. (orig./RHM)

ADHD symptoms impact smoking outcomes and withdrawal in response to Varenicline treatment for smoking cessation.

Science.gov (United States)

Bidwell, L Cinnamon; Karoly, Hollis C; Hutchison, Kent E; Bryan, Angela D

2017-10-01

Attention-Deficit/Hyperactivity Disorder (ADHD) is associated with nicotine dependence and difficulty quitting smoking. Few cessation trials specifically consider the impact of ADHD on treatment outcomes, including those testing established pharmacological therapies, such as varenicline. The current study focused on the impact of pretreatment ADHD inattention (IN) and hyperactivity-impulsivity (HI) symptoms on treatment outcome in a randomized controlled trial of varenicline [N=205, average age=34.13(10.07), average baseline cigarettes per day=14.71(7.06)]. Given that varenicline's putative therapeutic mechanism is attenuation of withdrawal severity during abstinence, we also tested changes in withdrawal as a mediator of treatment effects in high and low ADHD groups. ADHD symptom severity in this sample was in the subclinical range. Cessation was associated with HI, but not IN, such that high HI individuals on varenicline reported the lowest smoking levels at the end of treatment across all groups (3.06cig/day for high HI vs 4.02cig/day for low HI). Individuals with high HI who received placebo had the highest smoking at the end of treatment (7.69cigs/day for high HI vs 5.56cig/day for low HI). Patterns continued at follow-up. Varenicline significantly reduced withdrawal for those with high HI, but not low HI. However, path models did not support an indirect effect of medication on reducing smoking via withdrawal in either group, suggesting that unmeasured variables are involved in varenicline's effect on reducing smoking. These data add to a gap in the smoking cessation literature regarding the impact of ADHD symptoms on the efficacy and mechanisms of frontline pharmacological treatments. Copyright © 2017 Elsevier B.V. All rights reserved.

High performance data transfer

Science.gov (United States)

Cottrell, R.; Fang, C.; Hanushevsky, A.; Kreuger, W.; Yang, W.

2017-10-01

The exponentially increasing need for high speed data transfer is driven by big data, and cloud computing together with the needs of data intensive science, High Performance Computing (HPC), defense, the oil and gas industry etc. We report on the Zettar ZX software. This has been developed since 2013 to meet these growing needs by providing high performance data transfer and encryption in a scalable, balanced, easy to deploy and use way while minimizing power and space utilization. In collaboration with several commercial vendors, Proofs of Concept (PoC) consisting of clusters have been put together using off-the- shelf components to test the ZX scalability and ability to balance services using multiple cores, and links. The PoCs are based on SSD flash storage that is managed by a parallel file system. Each cluster occupies 4 rack units. Using the PoCs, between clusters we have achieved almost 200Gbps memory to memory over two 100Gbps links, and 70Gbps parallel file to parallel file with encryption over a 5000 mile 100Gbps link.

Strategy Guideline. Partnering for High Performance Homes

Energy Technology Data Exchange (ETDEWEB)

Prahl, Duncan [IBACOS, Inc., Pittsburgh, PA (United States)

2013-01-01

High performance houses require a high degree of coordination and have significant interdependencies between various systems in order to perform properly, meet customer expectations, and minimize risks for the builder. Responsibility for the key performance attributes is shared across the project team and can be well coordinated through advanced partnering strategies. For high performance homes, traditional partnerships need to be matured to the next level and be expanded to all members of the project team including trades, suppliers, manufacturers, HERS raters, designers, architects, and building officials as appropriate. This guide is intended for use by all parties associated in the design and construction of high performance homes. It serves as a starting point and features initial tools and resources for teams to collaborate to continually improve the energy efficiency and durability of new houses.

High performance parallel I/O

CERN Document Server

Prabhat

2014-01-01

Gain Critical Insight into the Parallel I/O EcosystemParallel I/O is an integral component of modern high performance computing (HPC), especially in storing and processing very large datasets to facilitate scientific discovery. Revealing the state of the art in this field, High Performance Parallel I/O draws on insights from leading practitioners, researchers, software architects, developers, and scientists who shed light on the parallel I/O ecosystem.The first part of the book explains how large-scale HPC facilities scope, configure, and operate systems, with an emphasis on choices of I/O har

France’s State of the Art Distributed Optical Fibre Sensors Qualified for the Monitoring of the French Underground Repository for High Level and Intermediate Level Long Lived Radioactive Wastes

Directory of Open Access Journals (Sweden)

Sylvie Delepine-Lesoille

2017-06-01

Full Text Available This paper presents the state of the art distributed sensing systems, based on optical fibres, developed and qualified for the French Cigéo project, the underground repository for high level and intermediate level long-lived radioactive wastes. Four main parameters, namely strain, temperature, radiation and hydrogen concentration are currently investigated by optical fibre sensors, as well as the tolerances of selected technologies to the unique constraints of the Cigéo’s severe environment. Using fluorine-doped silica optical fibre surrounded by a carbon layer and polyimide coating, it is possible to exploit its Raman, Brillouin and Rayleigh scattering signatures to achieve the distributed sensing of the temperature and the strain inside the repository cells of radioactive wastes. Regarding the dose measurement, promising solutions are proposed based on Radiation Induced Attenuation (RIA responses of sensitive fibres such as the P-doped ones. While for hydrogen measurements, the potential of specialty optical fibres with Pd particles embedded in their silica matrix is currently studied for this gas monitoring through its impact on the fibre Brillouin signature evolution.

France’s State of the Art Distributed Optical Fibre Sensors Qualified for the Monitoring of the French Underground Repository for High Level and Intermediate Level Long Lived Radioactive Wastes

Science.gov (United States)

Delepine-Lesoille, Sylvie; Girard, Sylvain; Landolt, Marcel; Bertrand, Johan; Planes, Isabelle; Boukenter, Aziz; Marin, Emmanuel; Humbert, Georges; Leparmentier, Stéphanie; Auguste, Jean-Louis; Ouerdane, Youcef

2017-01-01

This paper presents the state of the art distributed sensing systems, based on optical fibres, developed and qualified for the French Cigéo project, the underground repository for high level and intermediate level long-lived radioactive wastes. Four main parameters, namely strain, temperature, radiation and hydrogen concentration are currently investigated by optical fibre sensors, as well as the tolerances of selected technologies to the unique constraints of the Cigéo’s severe environment. Using fluorine-doped silica optical fibre surrounded by a carbon layer and polyimide coating, it is possible to exploit its Raman, Brillouin and Rayleigh scattering signatures to achieve the distributed sensing of the temperature and the strain inside the repository cells of radioactive wastes. Regarding the dose measurement, promising solutions are proposed based on Radiation Induced Attenuation (RIA) responses of sensitive fibres such as the P-doped ones. While for hydrogen measurements, the potential of specialty optical fibres with Pd particles embedded in their silica matrix is currently studied for this gas monitoring through its impact on the fibre Brillouin signature evolution. PMID:28608831

ADVANCED HIGH PERFORMANCE SOLID WALL BLANKET CONCEPTS

International Nuclear Information System (INIS)

WONG, CPC; MALANG, S; NISHIO, S; RAFFRAY, R; SAGARA, S

2002-01-01

OAK A271 ADVANCED HIGH PERFORMANCE SOLID WALL BLANKET CONCEPTS. First wall and blanket (FW/blanket) design is a crucial element in the performance and acceptance of a fusion power plant. High temperature structural and breeding materials are needed for high thermal performance. A suitable combination of structural design with the selected materials is necessary for D-T fuel sufficiency. Whenever possible, low afterheat, low chemical reactivity and low activation materials are desired to achieve passive safety and minimize the amount of high-level waste. Of course the selected fusion FW/blanket design will have to match the operational scenarios of high performance plasma. The key characteristics of eight advanced high performance FW/blanket concepts are presented in this paper. Design configurations, performance characteristics, unique advantages and issues are summarized. All reviewed designs can satisfy most of the necessary design goals. For further development, in concert with the advancement in plasma control and scrape off layer physics, additional emphasis will be needed in the areas of first wall coating material selection, design of plasma stabilization coils, consideration of reactor startup and transient events. To validate the projected performance of the advanced FW/blanket concepts the critical element is the need for 14 MeV neutron irradiation facilities for the generation of necessary engineering design data and the prediction of FW/blanket components lifetime and availability

DOE research in utilization of high-performance computers

International Nuclear Information System (INIS)

Buzbee, B.L.; Worlton, W.J.; Michael, G.; Rodrigue, G.

1980-12-01

Department of Energy (DOE) and other Government research laboratories depend on high-performance computer systems to accomplish their programatic goals. As the most powerful computer systems become available, they are acquired by these laboratories so that advances can be made in their disciplines. These advances are often the result of added sophistication to numerical models whose execution is made possible by high-performance computer systems. However, high-performance computer systems have become increasingly complex; consequently, it has become increasingly difficult to realize their potential performance. The result is a need for research on issues related to the utilization of these systems. This report gives a brief description of high-performance computers, and then addresses the use of and future needs for high-performance computers within DOE, the growing complexity of applications within DOE, and areas of high-performance computer systems warranting research. 1 figure

Na effect on flexible Cu(In,Ga)Se{sub 2} photovoltaic cell depending on diffusion barriers (SiOx, i-ZnO) on stainless steel

Energy Technology Data Exchange (ETDEWEB)

Lee, Woo-Jung; Cho, Dae-Hyung; Wi, Jae-Hyung; Han, Won Seok [Electronics and Telecommunications Research Institute, Daejeon 305-700 (Korea, Republic of); Kim, Jeha [Insitute of Photovoltaics, Cheongju University, Cheongju 360-764 (Korea, Republic of); Chung, Yong-Duck, E-mail: ydchung@etri.re.kr [Electronics and Telecommunications Research Institute, Daejeon 305-700 (Korea, Republic of); Department of Advanced Device Engineering, Korea University of Science and Technology, Daejeon 305-350 (Korea, Republic of)

2014-10-15

Cu(In,Ga)Se{sub 2} (CIGS) based-photovoltaic (PV) cells with different diffusion barriers of SiOx and i-ZnO were fabricated on stainless steel (STS) substrate and their electrical characteristics were investigated by measuring J–V curves under illuminated and dark conditions. The physical properties of the CIGS film depending on type of diffusion barrier were also analyzed using X-ray diffraction and secondary ion mass spectroscopy. The efficiency of the CIGS-PV cell with i-ZnO barrier was approximately 2% higher than that with the SiOx barrier. Through the analysis of dark J–V curves, we discovered that distinctive defects were formed in the band gap of CIGS based on which diffusion barrier contacted the STS. The diffraction pattern showed a slightly different tendency of the peak intensity ratio of (220/204)/(112) in the PV cell with the i-ZnO barrier, which was slightly higher than that in the PV cell with SiOx barrier. In elemental depth profile, a deficient Ga profile was observed near the surface of the CIGS film with the SiOx barrier, and an abundant Na profile within the CIGS film with the i-ZnO barrier was detected. This is attributed to a difference in thermal conduction through the diffusion barriers during CIGS film growth, originating from the larger thermal conductivity of ZnO compared with SiOx. - Highlights: • We fabricated CIGS-PV cells with diffusion barriers of SiOx and i-ZnO on STS. • The efficiency of CIGS-PV cell with i-ZnO was ∼2% higher than that with SiOx. • Distinctive defects were formed into CIGS absorber depending on diffusion barrier.

High-performance mass storage system for workstations

Science.gov (United States)

Chiang, T.; Tang, Y.; Gupta, L.; Cooperman, S.

1993-01-01

Reduced Instruction Set Computer (RISC) workstations and Personnel Computers (PC) are very popular tools for office automation, command and control, scientific analysis, database management, and many other applications. However, when using Input/Output (I/O) intensive applications, the RISC workstations and PC's are often overburdened with the tasks of collecting, staging, storing, and distributing data. Also, by using standard high-performance peripherals and storage devices, the I/O function can still be a common bottleneck process. Therefore, the high-performance mass storage system, developed by Loral AeroSys' Independent Research and Development (IR&D) engineers, can offload a RISC workstation of I/O related functions and provide high-performance I/O functions and external interfaces. The high-performance mass storage system has the capabilities to ingest high-speed real-time data, perform signal or image processing, and stage, archive, and distribute the data. This mass storage system uses a hierarchical storage structure, thus reducing the total data storage cost, while maintaining high-I/O performance. The high-performance mass storage system is a network of low-cost parallel processors and storage devices. The nodes in the network have special I/O functions such as: SCSI controller, Ethernet controller, gateway controller, RS232 controller, IEEE488 controller, and digital/analog converter. The nodes are interconnected through high-speed direct memory access links to form a network. The topology of the network is easily reconfigurable to maximize system throughput for various applications. This high-performance mass storage system takes advantage of a 'busless' architecture for maximum expandability. The mass storage system consists of magnetic disks, a WORM optical disk jukebox, and an 8mm helical scan tape to form a hierarchical storage structure. Commonly used files are kept in the magnetic disk for fast retrieval. The optical disks are used as archive

Ground Glass Pozzolan in Conventional, High, and Ultra-High Performance Concrete

OpenAIRE

Tagnit-Hamou Arezki; Zidol Ablam; Soliman Nancy; Deschamps Joris; Omran Ahmed

2018-01-01

Ground-glass pozzolan (G) obtained by grinding the mixed-waste glass to same fineness of cement can act as a supplementary-cementitious material (SCM), given that it is an amorphous and a pozzolanic material. The G showed promising performances in different concrete types such as conventional concrete (CC), high-performance concrete (HPC), and ultra-high performance concrete (UHPC). The current paper reports on the characteristics and performance of G in these concrete types. The use of G pro...

E-cigarette knowledge, attitudes, and use in opioid dependent smokers.

Science.gov (United States)

Stein, Michael D; Caviness, Celeste M; Grimone, Kristin; Audet, Daniel; Borges, Allison; Anderson, Bradley J

2015-05-01

Individuals in treatment for opioid dependence have smoking rates 3-5 times greater than the U.S. prevalence rate. Traditional smoking cessation strategies have been ineffective in this population. Novel approaches are needed as well as harm reduction avenues. E-cigarettes (e-cigs) may provide such a novel harm reduction and cessation opportunity, but little is known about the knowledge of, attitudes about, and usage of e-cigs in opioid dependent smokers. The current study enrolled 315 opioid dependent smokers (164 methadone, 151 buprenorphine), treated in the same health system in Fall River, Massachusetts. The sample was 49.7% male and 85.1% non-Latino White. Overall 98.7% had heard of e-cigs, 73.0% had ever tried e-cigs, and 33.8% had used e-cigs in the past 30 days. The most common reasons for use were curiosity (41.4%) and to quit all nicotine (26.0%). The proportion of opioid dependent smokers that had ever tried e-cigs and used them in the past month was substantially greater than that found in recent general population surveys. While e-cigs have been used to quit smoking, how to optimize their utility as a cessation tool remains undefined. E-cigs should be a part of smoking cessation discussions with this vulnerable, difficult-to-treat population. Copyright © 2015 Elsevier Inc. All rights reserved.

Electronic Cigarettes for Curbing the Tobacco-Induced Burden of Noncommunicable Diseases: Evidence Revisited with Emphasis on Challenges in Sub-Saharan Africa

Directory of Open Access Journals (Sweden)

Jobert Richie N. Nansseu

2016-01-01

Full Text Available Introduction. This review examines whether electronic cigarettes (e-cigs implementation or vulgarization in sub-Saharan Africa (SSA could be helpful in curtailing the toll of tobacco smoking in the region. Discussion. There are about 1.3 billion smokers worldwide, with nearly 80% of them living in developing countries where the burden of tobacco-related illnesses and deaths is the heaviest. Studies report that e-cigs may facilitate smoking cessation, reduction, or abstinence and may pose only a small fraction of the risks of traditional tobacco cigarettes; e-cigs may also considerably reduce second-hand smoking. Thereby, implementation of e-cig use could help to substantially reduce the burden driven by tobacco smoking in SSA, in a particular context of lack of regulations and control policies towards this threat. However, the evidence is not clear on whether e-cigs are risk-free, especially if used in the long term. Conclusions. On the whole, if e-cigs were to be introduced in SSA, they should be strictly recommended to current and/or ex-smokers as a method to quit smoking or prevent relapse and never-smokers should be strongly encouraged to avoid using these devices. Bans on sales of e-cigs to youngsters should be legislated, e-cig advertisements prohibited, and their usage continuously controlled and monitored.

Correcting for interference effects in the photoluminescence of Cu(In,Ga)Se{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Wolter, Max Hilaire; Siebentritt, Susanne [Laboratory for Photovoltaics, Physics and Materials Science Research Unit, University of Luxembourg, 4422 Belvaux (Luxembourg); Bissig, Benjamin; Reinhard, Patrick; Buecheler, Stephan [Laboratory for Thin Films and Photovoltaics, Empa - Swiss Federal Laboratories for Materials Science and Technology, Ueberlandstr. 129, 8600 Duebendorf (Switzerland); Jackson, Philip [Zentrum fuer Sonnenenergie-und Wasserstoff-Forschung Baden-Wuerttemberg (ZSW), 70565 Stuttgart (Germany)

2017-06-15

Photoluminescence (PL) measurements are performed on high-quality Cu(In,Ga)Se{sub 2} (CIGS) thin films with the intention of investigating their electronic structure. Due to the nature of the CIGS absorbers, notably their smooth surface and a graded band gap, the measured PL spectra are distorted by interference effects, limiting thus the information that one can gain. Here we show that, by varying the entrance angle of the laser light and the detection angle of the emitted PL, we are able to correct for interference effects. As a result, we receive interference-free PL spectra that enable us to determine quantities such as band gap energies and quasi-Fermi level splittings (QFLS). Furthermore, we show that it is possible to measure the QFLS even without correcting for interference effects and we compare the QFLS to the open circuit voltage for a particular sample. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Review on Alkali Element Doping in Cu(In,GaSe2 Thin Films and Solar Cells

Directory of Open Access Journals (Sweden)

Yun Sun

2017-08-01

Full Text Available This paper reviews the development history of alkali element doping on Cu(In,GaSe2 (CIGS solar cells and summarizes important achievements that have been made in this field. The influences of incorporation strategies on CIGS absorbers and device performances are also reviewed. By analyzing CIGS surface structure and electronic property variation induced by alkali fluoride (NaF and KF post-deposition treatment (PDT, we discuss and interpret the following issues: ① The delamination of CIGS thin films induced by Na incorporation facilitates CuInSe2 formation and inhibits Ga during low-temperature co-evaporation processes. ② The mechanisms of carrier density increase due to defect passivation by Na at grain boundaries and the surface. ③ A thinner buffer layer improves the short-circuit current without open-circuit voltage loss. This is attributed not only to better buffer layer coverage in the early stage of the chemical bath deposition process, but also to higher donor defect (CdCu+ density, which is transferred from the acceptor defect (VCu− and strengthens the buried homojunction. ④ The KF-PDT-induced lower valence band maximum at the absorber surface reduces the recombination at the absorber/buffer interface, which improves the open-circuit voltage and the fill factor of solar cells.

Structural and electrical properties of co-evaporated Cu(In,Ga)Se{sub 2} thin films with varied Cu contents

Energy Technology Data Exchange (ETDEWEB)

Kim, Min Young; Kim, Girim; Kim, Jongwan; Park, Jae Hwan; Lim, Donggun, E-mail: dglim@ut.ac.kr

2013-11-01

Cu(In,Ga)Se{sub 2} (CIGS) thin films were fabricated with varying Cu contents. Cu/(Ga + In) ratios were varied between 0.4 and 1.02. Solar cells were then fabricated by co-evaporation using the CIGS layers as absorbers. The influences of Cu content on the cells' structural, optical and electrical properties were studied. The CIGS thin films were characterized by X-ray diffractometer, scanning electron microscopy, energy-dispersive spectroscopy, four-point probe measurement and Hall measurement. Grain size in the films increased with increasing Cu content. At a Cu/(Ga + In) ratio of 0.86, the (220/204) peak was stronger than the (112) peak and carrier concentration was 1.49 × 10{sup 16} cm{sup −3}. Optimizing the Cu content resulted in a CIGS solar cell with an efficiency of 16.5%. - Highlights: • Improvement of technique to form Cu(In,Ga)Se{sub 2} (CIGS) film by co-evaporation method • Cu/(In + Ga) ratio to improve the efficiency for CIGS thin film solar cell • Cu content effects have been analyzed. • Optimum condition of CIGS layer as an absorber of thin film solar cells.

Indoor Air Quality in High Performance Schools

Science.gov (United States)

High performance schools are facilities that improve the learning environment while saving energy, resources, and money. The key is understanding the lifetime value of high performance schools and effectively managing priorities, time, and budget.

Common-image gathers in the offset domain from reverse-time migration

KAUST Repository

Zhan, Ge

2014-04-01

Kirchhoff migration is flexible to output common-image gathers (CIGs) in the offset domain by imaging data with different offsets separately. These CIGs supply important information for velocity model updates and amplitude-variation-with-offset (AVO) analysis. Reverse-time migration (RTM) offers more insights into complex geology than Kirchhoff migration by accurately describing wave propagation using the two-way wave equation. But, it has difficulty to produce offset domain CIGs like Kirchhoff migration. In this paper, we develop a method for obtaining offset domain CIGs from RTM. The method first computes the RTM operator of an offset gather, followed by a dot product of the operator and the offset data to form a common-offset RTM image. The offset domain CIGs are then achieved after separately migrating data with different offsets. We generate offset domain CIGs on both the Marmousi synthetic data and 2D Gulf of Mexico real data using this approach. © 2014.

Advanced high performance solid wall blanket concepts

International Nuclear Information System (INIS)

Wong, C.P.C.; Malang, S.; Nishio, S.; Raffray, R.; Sagara, A.

2002-01-01

First wall and blanket (FW/blanket) design is a crucial element in the performance and acceptance of a fusion power plant. High temperature structural and breeding materials are needed for high thermal performance. A suitable combination of structural design with the selected materials is necessary for D-T fuel sufficiency. Whenever possible, low afterheat, low chemical reactivity and low activation materials are desired to achieve passive safety and minimize the amount of high-level waste. Of course the selected fusion FW/blanket design will have to match the operational scenarios of high performance plasma. The key characteristics of eight advanced high performance FW/blanket concepts are presented in this paper. Design configurations, performance characteristics, unique advantages and issues are summarized. All reviewed designs can satisfy most of the necessary design goals. For further development, in concert with the advancement in plasma control and scrape off layer physics, additional emphasis will be needed in the areas of first wall coating material selection, design of plasma stabilization coils, consideration of reactor startup and transient events. To validate the projected performance of the advanced FW/blanket concepts the critical element is the need for 14 MeV neutron irradiation facilities for the generation of necessary engineering design data and the prediction of FW/blanket components lifetime and availability

High-performance OPCPA laser system

International Nuclear Information System (INIS)

Zuegel, J.D.; Bagnoud, V.; Bromage, J.; Begishev, I.A.; Puth, J.

2006-01-01

Optical parametric chirped-pulse amplification (OPCPA) is ideally suited for amplifying ultra-fast laser pulses since it provides broadband gain across a wide range of wavelengths without many of the disadvantages of regenerative amplification. A high-performance OPCPA system has been demonstrated as a prototype for the front end of the OMEGA Extended Performance (EP) Laser System. (authors)

High-performance OPCPA laser system

Energy Technology Data Exchange (ETDEWEB)

Zuegel, J.D.; Bagnoud, V.; Bromage, J.; Begishev, I.A.; Puth, J. [Rochester Univ., Lab. for Laser Energetics, NY (United States)

2006-06-15

Optical parametric chirped-pulse amplification (OPCPA) is ideally suited for amplifying ultra-fast laser pulses since it provides broadband gain across a wide range of wavelengths without many of the disadvantages of regenerative amplification. A high-performance OPCPA system has been demonstrated as a prototype for the front end of the OMEGA Extended Performance (EP) Laser System. (authors)

High performance in software development

CERN Multimedia

CERN. Geneva; Haapio, Petri; Liukkonen, Juha-Matti

2015-01-01

What are the ingredients of high-performing software? Software development, especially for large high-performance systems, is one the most complex tasks mankind has ever tried. Technological change leads to huge opportunities but challenges our old ways of working. Processing large data sets, possibly in real time or with other tight computational constraints, requires an efficient solution architecture. Efficiency requirements span from the distributed storage and large-scale organization of computation and data onto the lowest level of processor and data bus behavior. Integrating performance behavior over these levels is especially important when the computation is resource-bounded, as it is in numerics: physical simulation, machine learning, estimation of statistical models, etc. For example, memory locality and utilization of vector processing are essential for harnessing the computing power of modern processor architectures due to the deep memory hierarchies of modern general-purpose computers. As a r...

High Performance Computing in Science and Engineering '16 : Transactions of the High Performance Computing Center, Stuttgart (HLRS) 2016

CERN Document Server

Kröner, Dietmar; Resch, Michael

2016-01-01

This book presents the state-of-the-art in supercomputer simulation. It includes the latest findings from leading researchers using systems from the High Performance Computing Center Stuttgart (HLRS) in 2016. The reports cover all fields of computational science and engineering ranging from CFD to computational physics and from chemistry to computer science with a special emphasis on industrially relevant applications. Presenting findings of one of Europe’s leading systems, this volume covers a wide variety of applications that deliver a high level of sustained performance. The book covers the main methods in high-performance computing. Its outstanding results in achieving the best performance for production codes are of particular interest for both scientists and engineers. The book comes with a wealth of color illustrations and tables of results.

High-performance computing — an overview

Science.gov (United States)

Marksteiner, Peter

1996-08-01

An overview of high-performance computing (HPC) is given. Different types of computer architectures used in HPC are discussed: vector supercomputers, high-performance RISC processors, various parallel computers like symmetric multiprocessors, workstation clusters, massively parallel processors. Software tools and programming techniques used in HPC are reviewed: vectorizing compilers, optimization and vector tuning, optimization for RISC processors; parallel programming techniques like shared-memory parallelism, message passing and data parallelism; and numerical libraries.

Team Development for High Performance Management.

Science.gov (United States)

Schermerhorn, John R., Jr.

1986-01-01

The author examines a team development approach to management that creates shared commitments to performance improvement by focusing the attention of managers on individual workers and their task accomplishments. It uses the "high-performance equation" to help managers confront shared beliefs and concerns about performance and develop realistic…

Interfacial Modifiers

Energy Technology Data Exchange (ETDEWEB)

Martin, Ina; French, Roger H.

2018-03-19

Our project objective in the first and only Budget Period was to demonstrate the potential of nm-scale organofunctional silane coatings as a method of extending the lifetime of PV materials and devices. Specifically, the target was to double the lifetime performance of a laminated Cu(In,Ga)Se2 (CIGS) cell under real-world and accelerated aging exposure conditions. Key findings are that modification of aluminum-doped zinc oxide (AZO) films (materials used as transparent conductive oxide (TCO) top contacts) resulted in decreased degradation of optical and electrical properties under damp heat (DH) exposure compared to un-modified AZO. The most significant finding is that modification of the AZO top contact of full CIGS devices resulted in significantly improved properties under DH exposure compared to un-modified devices, by a factor of 4 after 1000 h. Results of this one-year project have demonstrated that surface functionalization is a viable pathway for extending the lifetime of state-of-the-art CIGS devices.

The influence of different locations of sputter guns on the morphological and structural properties of Cu–In–Ga precursors and Cu(In,Ga)Se{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Wang, J.; Zhu, J., E-mail: jiezhu@ustb.edu.cn; He, Y.X.

2014-01-01

The influence of two different locations of sputter guns on the morphological and structural properties of Cu–In–Ga precursors and Cu(In,Ga)Se{sub 2} (CIGS) thin films was investigated. All the precursors contained cauliflower-like nodules, whereas smaller subnodules were observed on the background. All the precursors revealed apparent three-layered structures, and voids were observed at the CIGS/SLG interface of Sets 1 and 2 films rather than Set 3 film. EDS results indicated that all CIGS thin films were Cu-deficient. Based on the grazing incidence X-ray diffraction (GIXRD) patterns, as-selenized films showed peaks corresponding to the chalcopyrite-type CIGS structure. Depth-resolved Raman spectra showed the formation of a dominant CIGS phase inside the films for all the as-selenized samples investigated, and of an ordered vacancy compound (OVC) phase like Cu(In,Ga){sub 3}Se{sub 5} or Cu(In,Ga){sub 2}Se{sub 3.5} at the surface and/or CIGS/SLG interface region of Sets 2 and 3 films. No evidence was obtained on the presence of an OVC phase in Set 1 CIGS film, which may be speculated that long-time annealing is contributed to suppress the growth of OVC phases. The results of the present work suggest that the metallic precursors deposited with the upright-location sputter gun might be more appropriate to prepare CIGS thin films than those sputtered with the titled-location gun.

High Performance Walls in Hot-Dry Climates

Energy Technology Data Exchange (ETDEWEB)

Hoeschele, Marc [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States); Springer, David [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States); Dakin, Bill [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States); German, Alea [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States)

2015-01-01

High performance walls represent a high priority measure for moving the next generation of new homes to the Zero Net Energy performance level. The primary goal in improving wall thermal performance revolves around increasing the wall framing from 2x4 to 2x6, adding more cavity and exterior rigid insulation, achieving insulation installation criteria meeting ENERGY STAR's thermal bypass checklist. To support this activity, in 2013 the Pacific Gas & Electric Company initiated a project with Davis Energy Group (lead for the Building America team, Alliance for Residential Building Innovation) to solicit builder involvement in California to participate in field demonstrations of high performance wall systems. Builders were given incentives and design support in exchange for providing site access for construction observation, cost information, and builder survey feedback. Information from the project was designed to feed into the 2016 Title 24 process, but also to serve as an initial mechanism to engage builders in more high performance construction strategies. This Building America project utilized information collected in the California project.

Flexible nanoscale high-performance FinFETs

KAUST Repository

Sevilla, Galo T.

2014-10-28

With the emergence of the Internet of Things (IoT), flexible high-performance nanoscale electronics are more desired. At the moment, FinFET is the most advanced transistor architecture used in the state-of-the-art microprocessors. Therefore, we show a soft-etch based substrate thinning process to transform silicon-on-insulator (SOI) based nanoscale FinFET into flexible FinFET and then conduct comprehensive electrical characterization under various bending conditions to understand its electrical performance. Our study shows that back-etch based substrate thinning process is gentler than traditional abrasive back-grinding process; it can attain ultraflexibility and the electrical characteristics of the flexible nanoscale FinFET show no performance degradation compared to its rigid bulk counterpart indicating its readiness to be used for flexible high-performance electronics.

Factors associated with experimentation of electronic cigarettes among Parisian teenagers in 2013.

Science.gov (United States)

Dautzenberg, Bertrand; Berlin, Ivan; Tanguy, Marie-Laure; Rieu, Nicole; Birkui, Pierre

2015-01-01

Electronic cigarettes (e-cig.) became widely used among adults. Data are insufficient about e-cig. experimentation among youth. To assess prevalence of e-cig. experimentation and associated factors among the 12 to 19 years old we analyse a cross sectional school based survey in the city of Paris, France in 2013 on a randomly selected sample of 2 % of schoolchildren (n = 3 279). Self-report questionnaire include demographic, individual and family smoking characteristics and questions about e-cig: "Have you ever used an e-cigarette?"- "Did you use e-cigarette in the last 30 days?"-"Did you try e-cigarette as a first tobacco product?". In 2013, 17.9 % (564) schoolchildren reported having experienced the e-cig (boys: 19.0 %, girls: 16.8 %) compared to 9.8 % in 2012. Experimentation rate increases from 5 % among the 12 to 30 % among the 16-year-old. E-cig. experimentation was significantly associated with 11 parameters including : age >15 years (OR: 0.66 (IC95 % = 0.46-0.94)); smoking 10 cigarettes or more (OR = 5.67 (IC95 % = 3.11-10.34)), best friends and siblings smoker (OR = 1.54 (IC95 % = 1.11-2.14)) and (OR = 1.88 (IC95 % = 1.41-2.52)); experimentation of shisha (OR = 2.60 (IC95 % = 1.75-3.86)), cannabis use (OR = 1.90 (IC95 % = 1.32-2.72)); having two parents who forbid smoking (OR = 2.32 (IC95 % = 1.63-3.30)). Only 5.6 % of the study population (and 32.5 % of e-cig. experimenters (183/564)) have used it in the last 30 days; 1.7 % of the study population and 10.0 % of e-cig. experimenters were non-smokers (56/564). Rate of e-cig. experimentation among schoolchildren increased by 8.1 % in 1 year. Non-smoking youth may use e-cig. Prospective studies are urgently needed to assess the evolution of e-cig. use both among smoking and non-smoking youth.

In-situ optical emission spectroscopy for a better control of hybrid sputtering/evaporation process for the deposition of Cu(In,Ga)Se{sub 2} layers

Energy Technology Data Exchange (ETDEWEB)

Posada, Jorge; Jubault, Marie [Institute of Research and Development on Photovoltaic Energy (IRDEP), EDF-CNRS-Chimie ParisTech, UMR 7174, 6 Quai Watier, 78401 Chatou (France); Bousquet, Angélique; Tomasella, Eric [Clermont Université, Université Blaise Pascal, Institute of Chemistry of Clermont-Ferrand (ICCF), CNRS-UMR 6296, 24 Avenue des Landais, 63171 Aubière (France); Lincot, Daniel [Institute of Research and Development on Photovoltaic Energy (IRDEP), EDF-CNRS-Chimie ParisTech, UMR 7174, 6 Quai Watier, 78401 Chatou (France)

2015-05-01

In this work, we have developed a hybrid one-step co-sputtering/evaporation Cu(In,Ga)Se{sub 2} (CIGS) process, where Cu, In and Ga are sputtered simultaneously with the thermal evaporation of selenium, thus avoiding the H{sub 2}Se use. An appropriate control of the selenium flux is very important to prevent the target poisoning and hence some material flux variations. Indeed, the control of the CIGS composition must be rigorous to ensure reproducible solar cell properties. In this regard, a study of the correlations between plasma species and thin film composition, structure and morphology has been performed by varying power values and Se evaporation temperature in the 170 to 230 °C range. We started by studying the plasma with a powerful technique: optical emission spectroscopy, following light emissions from different plasma species: sputtered Cu, Ga, In but also evaporated Se. Hence, we determined the Se flow threshold avoiding target poisoning and the main parameter controlling the CIGS composition. Obviously, we also focused our interest on the material. We measured film composition and thickness of the samples with X-ray fluorescence and by energy dispersive X-ray. Different phases formed during the process were identified by Raman spectroscopy and X-ray diffraction. The optoelectronic cell properties showed promising efficiency of 10.3% for an absorber with composition ratios of [Cu]/([In] + [Ga]) = 1.02 and [Ga]/([In] + [Ga]) = 0.44. Finally, this work shows that we are able to control this hybrid process and thus the structure and composition of CIGS thin film for industrial transfer in the photovoltaic field. - Highlights: • We have developed a hybrid one-step co-sputtering/evaporation Cu(In,Ga)Se{sub 2} process. • Correlations between plasma species and thin film composition have been performed. • We determined the Se flow threshold avoiding target poisoning. • Efficient small-area CIGS cells with 10.3% efficiency were fabricated.

Triangle islands and cavities on the surface of evaporated Cu(In, Ga)Se2 absorber layer

International Nuclear Information System (INIS)

Han Anjun; Zhang Yi; Liu Wei; Li Boyan; Sun Yun

2012-01-01

Highlights: ► Lots of uncommon triangle islands and cavities are found on (1 1 2) planes terminated by Se atoms of evaporated Cu(In, Ga)Se 2 thin films. ► Se ad-dimer as a nucleus, Cu atom diffusion from Cu(In, Ga)Se 2 grains brings the epitaxial triangle island. ► The triangle islands grow with a two-dimensional layered mode. ► The triangle cavities are formed due to the insufficient coalescence of triangle islands. ► The performance of solar cell without triangle islands is improved. - Abstract: Cu(In, Ga)Se 2 (CIGS) thin films are co-evaporated at a constant substrate temperature of 500 °C on the Mo/soda lime glass substrates. The structural properties and chemical composition of the CIGS films are studied by an X-ray diffractometer (XRD) and an X-ray fluorescent spectrometer (XRF), respectively. A scanning electron microscope (SEM) is used to study the surface morphology. Lots of uncommon triangle islands and cavities are found on some planes of the CIGS thin films. We investigate the formation mechanism of these triangle islands. It is found that the planes with the triangle islands are (1 1 2) planes terminated by Se atoms. Se ad-dimer as a nucleus, Cu diffusion from CIGS grains brings the epitaxial triangle islands which grow with a two-dimensional layered mode. The film with Cu/(Ga + In) = 0.94–0.98 is one key of the formation of these islands. The triangle cavities are formed due to the insufficient coalescence of triangle islands. The growth of triangle islands brings a compact surface with large layered grains and many jagged edges, but no triangle cavity. Finally, we compare the performance of solar cell with triangle islands and layered gains. It is found that the performance of solar cell with large layered gains is improved.

The Role of Performance Management in Creating and Maintaining a High-Performance Organization

Directory of Open Access Journals (Sweden)

André A. de Waal

2015-04-01

Full Text Available There is still a good deal of confusion in the literature about how the use of a performance management system affects overall organizational performance. Some researchers find that performance management enhances both the financial and non-financial results of an organization, while others do not find any positive effects or, at most, ambiguous effects. An important step toward getting more clarity in this relationship is to investigate the role performance management plays in creating and maintaining a high-performance organization (HPO. The purpose of this study is to integrate performance management analysis (PMA and high-performance organization (HPO. A questionnaire combining questions on PMA dimensions and HPO factors was administered to two European-based multinational firms. Based on 468 valid questionnaires, a correlation analysis was performed on the PMA dimensions and the HPO factors in order to test the impact of performance management on the factors of high organizational performance. The results show strong and significant correlations between all the PMA dimensions and all the HPO factors, indicating that a performance management system that fosters performance-driven behavior in the organization is of critical importance to strengthen overall financial and non-financial performance.

Development of new high-performance stainless steels

International Nuclear Information System (INIS)

Park, Yong Soo

2002-01-01

This paper focused on high-performance stainless steels and their development status. Effect of nitrogen addition on super-stainless steel was discussed. Research activities at Yonsei University, on austenitic and martensitic high-performance stainless, steels, and the next-generation duplex stainless steels were introduced

vSphere high performance cookbook

CERN Document Server

Sarkar, Prasenjit

2013-01-01

vSphere High Performance Cookbook is written in a practical, helpful style with numerous recipes focusing on answering and providing solutions to common, and not-so common, performance issues and problems.The book is primarily written for technical professionals with system administration skills and some VMware experience who wish to learn about advanced optimization and the configuration features and functions for vSphere 5.1.

High Burnup Fuel Performance and Safety Research

Energy Technology Data Exchange (ETDEWEB)

Bang, Je Keun; Lee, Chan Bok; Kim, Dae Ho (and others)

2007-03-15

The worldwide trend of nuclear fuel development is to develop a high burnup and high performance nuclear fuel with high economies and safety. Because the fuel performance evaluation code, INFRA, has a patent, and the superiority for prediction of fuel performance was proven through the IAEA CRP FUMEX-II program, the INFRA code can be utilized with commercial purpose in the industry. The INFRA code was provided and utilized usefully in the universities and relevant institutes domesticallly and it has been used as a reference code in the industry for the development of the intrinsic fuel rod design code.

Oxide nanoparticle-based fabrication and optical properties of Cu(In1−xGax)S2 absorber layer for solar cells

International Nuclear Information System (INIS)

Choi, Yo-Min; Lee, Young-In; Kim, Bum-Sung; Choa, Yong-Ho

2013-01-01

The compound Cu(In 1−x Ga x )S 2 (CIGS) was synthesized using copper oxide, indium oxide and gallium oxide mixture (CIGO) nanoparticles using salt-assisted ultrasonic spray pyrolysis (SAUSP). Under this method, CIGS can be produced without the complicated restrictions of a vacuum and an inert atmosphere. The band gap of CIGS can be controlled by introducing the desired stoichiometric quantities of starting materials. In order to synthesize CIGO nanoparticles, various NaCl/precursor ratios were used to accomplish the SAUSP process and ultimately monodisperse CIGO nanoparticles with average particle size of 9 nm without hard agglomeration were obtained. Subsequently, the CIGO nanoparticles were sulfurized to form the CIGS in H 2 S/Ar atmosphere at 500 °C. The CIGS obtained in the present study has the various band gap ranging from 1.67 to 2.34 eV depending on the Ga / (In + Ga) ratio, and those band gap correspond to the respective bulk materials. - Highlights: • CIGS is obtained using Cu, In and Ga oxide mixture (CIGO) nanoparticles. • Salt-assisted ultrasonic spray pyrolysis is used to synthesize CIGO nanoparticles. • Nine nanometers of monodisperse CIGO nanoparticles without hard agglomeration is obtained. • The band gap of CIGS can be controlled by introducing the desired ratio of precursor

Danish High Performance Concretes

DEFF Research Database (Denmark)

Nielsen, M. P.; Christoffersen, J.; Frederiksen, J.

1994-01-01

In this paper the main results obtained in the research program High Performance Concretes in the 90's are presented. This program was financed by the Danish government and was carried out in cooperation between The Technical University of Denmark, several private companies, and Aalborg University...... concretes, workability, ductility, and confinement problems....

Promising high monetary rewards for future task performance increases intermediate task performance.

Directory of Open Access Journals (Sweden)

Claire M Zedelius

Full Text Available In everyday life contexts and work settings, monetary rewards are often contingent on future performance. Based on research showing that the anticipation of rewards causes improved task performance through enhanced task preparation, the present study tested the hypothesis that the promise of monetary rewards for future performance would not only increase future performance, but also performance on an unrewarded intermediate task. Participants performed an auditory Simon task in which they responded to two consecutive tones. While participants could earn high vs. low monetary rewards for fast responses to every second tone, their responses to the first tone were not rewarded. Moreover, we compared performance under conditions in which reward information could prompt strategic performance adjustments (i.e., when reward information was presented for a relatively long duration to conditions preventing strategic performance adjustments (i.e., when reward information was presented very briefly. Results showed that high (vs. low rewards sped up both rewarded and intermediate, unrewarded responses, and the effect was independent of the duration of reward presentation. Moreover, long presentation led to a speed-accuracy trade-off for both rewarded and unrewarded tones, whereas short presentation sped up responses to rewarded and unrewarded tones without this trade-off. These results suggest that high rewards for future performance boost intermediate performance due to enhanced task preparation, and they do so regardless whether people respond to rewards in a strategic or non-strategic manner.

Promising high monetary rewards for future task performance increases intermediate task performance.

Science.gov (United States)

Zedelius, Claire M; Veling, Harm; Bijleveld, Erik; Aarts, Henk

2012-01-01

In everyday life contexts and work settings, monetary rewards are often contingent on future performance. Based on research showing that the anticipation of rewards causes improved task performance through enhanced task preparation, the present study tested the hypothesis that the promise of monetary rewards for future performance would not only increase future performance, but also performance on an unrewarded intermediate task. Participants performed an auditory Simon task in which they responded to two consecutive tones. While participants could earn high vs. low monetary rewards for fast responses to every second tone, their responses to the first tone were not rewarded. Moreover, we compared performance under conditions in which reward information could prompt strategic performance adjustments (i.e., when reward information was presented for a relatively long duration) to conditions preventing strategic performance adjustments (i.e., when reward information was presented very briefly). Results showed that high (vs. low) rewards sped up both rewarded and intermediate, unrewarded responses, and the effect was independent of the duration of reward presentation. Moreover, long presentation led to a speed-accuracy trade-off for both rewarded and unrewarded tones, whereas short presentation sped up responses to rewarded and unrewarded tones without this trade-off. These results suggest that high rewards for future performance boost intermediate performance due to enhanced task preparation, and they do so regardless whether people respond to rewards in a strategic or non-strategic manner.

Comparison of ultra high performance supercritical fluid chromatography, ultra high performance liquid chromatography, and gas chromatography for the separation of synthetic cathinones.

Science.gov (United States)

Carnes, Stephanie; O'Brien, Stacey; Szewczak, Angelica; Tremeau-Cayel, Lauriane; Rowe, Walter F; McCord, Bruce; Lurie, Ira S

2017-09-01

A comparison of ultra high performance supercritical fluid chromatography, ultra high performance liquid chromatography, and gas chromatography for the separation of synthetic cathinones has been conducted. Nine different mixtures of bath salts were analyzed in this study. The three different chromatographic techniques were examined using a general set of controlled synthetic cathinones as well as a variety of other synthetic cathinones that exist as positional isomers. Overall 35 different synthetic cathinones were analyzed. A variety of column types and chromatographic modes were examined for developing each separation. For the ultra high performance supercritical fluid chromatography separations, analyses were performed using a series of Torus and Trefoil columns with either ammonium formate or ammonium hydroxide as additives, and methanol, ethanol or isopropanol organic solvents as modifiers. Ultra high performance liquid chromatographic separations were performed in both reversed phase and hydrophilic interaction chromatographic modes using SPP C18 and SPP HILIC columns. Gas chromatography separations were performed using an Elite-5MS capillary column. The orthogonality of ultra high performance supercritical fluid chromatography, ultra high performance liquid chromatography, and gas chromatography was examined using principal component analysis. For the best overall separation of synthetic cathinones, the use of ultra high performance supercritical fluid chromatography in combination with gas chromatography is recommended. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High Performance Electronics on Flexible Silicon

KAUST Repository

Sevilla, Galo T.

2016-09-01

Over the last few years, flexible electronic systems have gained increased attention from researchers around the world because of their potential to create new applications such as flexible displays, flexible energy harvesters, artificial skin, and health monitoring systems that cannot be integrated with conventional wafer based complementary metal oxide semiconductor processes. Most of the current efforts to create flexible high performance devices are based on the use of organic semiconductors. However, inherent material\\'s limitations make them unsuitable for big data processing and high speed communications. The objective of my doctoral dissertation is to develop integration processes that allow the transformation of rigid high performance electronics into flexible ones while maintaining their performance and cost. In this work, two different techniques to transform inorganic complementary metal-oxide-semiconductor electronics into flexible ones have been developed using industry compatible processes. Furthermore, these techniques were used to realize flexible discrete devices and circuits which include metal-oxide-semiconductor field-effect-transistors, the first demonstration of flexible Fin-field-effect-transistors, and metal-oxide-semiconductors-based circuits. Finally, this thesis presents a new technique to package, integrate, and interconnect flexible high performance electronics using low cost additive manufacturing techniques such as 3D printing and inkjet printing. This thesis contains in depth studies on electrical, mechanical, and thermal properties of the fabricated devices.

High Performance Computing in Science and Engineering '02 : Transactions of the High Performance Computing Center

CERN Document Server

Jäger, Willi

2003-01-01

This book presents the state-of-the-art in modeling and simulation on supercomputers. Leading German research groups present their results achieved on high-end systems of the High Performance Computing Center Stuttgart (HLRS) for the year 2002. Reports cover all fields of supercomputing simulation ranging from computational fluid dynamics to computer science. Special emphasis is given to industrially relevant applications. Moreover, by presenting results for both vector sytems and micro-processor based systems the book allows to compare performance levels and usability of a variety of supercomputer architectures. It therefore becomes an indispensable guidebook to assess the impact of the Japanese Earth Simulator project on supercomputing in the years to come.

Critical Factors Explaining the Leadership Performance of High-Performing Principals

Science.gov (United States)

Hutton, Disraeli M.

2018-01-01

The study explored critical factors that explain leadership performance of high-performing principals and examined the relationship between these factors based on the ratings of school constituents in the public school system. The principal component analysis with the use of Varimax Rotation revealed that four components explain 51.1% of the…

High Performance Walls in Hot-Dry Climates

Energy Technology Data Exchange (ETDEWEB)

Hoeschele, Marc [National Renewable Energy Lab. (NREL), Golden, CO (United States); Springer, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Dakin, Bill [National Renewable Energy Lab. (NREL), Golden, CO (United States); German, Alea [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2015-01-01

High performance walls represent a high priority measure for moving the next generation of new homes to the Zero Net Energy performance level. The primary goal in improving wall thermal performance revolves around increasing the wall framing from 2x4 to 2x6, adding more cavity and exterior rigid insulation, achieving insulation installation criteria meeting ENERGY STAR's thermal bypass checklist, and reducing the amount of wood penetrating the wall cavity.

High-performance liquid chromatography of oligoguanylates at high pH

Science.gov (United States)

Stribling, R.; Deamer, D. (Principal Investigator)

1991-01-01

Because of the stable self-structures formed by oligomers of guanosine, standard high-performance liquid chromatography techniques for oligonucleotide fractionation are not applicable. Previously, oligoguanylate separations have been carried out at pH 12 using RPC-5 as the packing material. While RPC-5 provides excellent separations, there are several limitations, including the lack of a commercially available source. This report describes a new anion-exchange high-performance liquid chromatography method using HEMA-IEC BIO Q, which successfully separates different forms of the guanosine monomer as well as longer oligoguanylates. The reproducibility and stability at high pH suggests a versatile role for this material.

Knowledge on Irradiation, Medical Imaging Prescriptions, and Clinical Imaging Referral Guidelines among Physicians in a Sub-Saharan African Country (Cameroon).

Science.gov (United States)

Moifo, Boniface; Tene, Ulrich; Moulion Tapouh, Jean Roger; Samba Ngano, Odette; Tchemtchoua Youta, Justine; Simo, Augustin; Gonsu Fotsin, Joseph

2017-01-01

Clinical imaging guidelines (CIGs) are suitable tools to enhance justification of imaging procedures. To assess physicians' knowledge on irradiation, their self-perception of imaging prescriptions, and the use of CIGs. A questionnaire of 21 items was self-administered between July and August 2016 to 155 referring physicians working in seven university-affiliated hospitals in Yaoundé and Douala (Cameroon). This pretested questionnaire based on imaging referral practices, the use and the need of CIGs, knowledge on radiation doses of 11 specific radiologic procedures, and knowledge of injurious effects of radiation was completed in the presence of the investigator. Scores were allocated for each question. 155 questionnaires were completed out of 180 administered (86.1%). Participants were 90 (58%) females, 63 (40.64%) specialists, 53 (34.20%) residents/interns, and 39 (25.16%) general practitioners. The average professional experience was 7.4 years (1-25 years). The mean knowledge score was 11.5/59 with no influence of sex, years of experience, and professional category. CIGs users' score was better than nonusers (means 14.2 versus 10.6; p imaging exams. Seventy-eight (50.3%) participants have knowledge on CIGs and half of them made use of them. "Impact on diagnosis" was the highest justification criteria follow by "impact on treatment decision." Unjustified requests were mainly for "patient expectation or will" or for "research motivations." 96% of interviewees believed that making available national CIGs will improve justification. Most physicians did not have appropriate awareness about radiation doses for routine imaging procedures. A small number of physicians have knowledge on CIGs but they believe that making available CIGs will improve justification of imaging procedures. Continuous trainings on radiation protection and implementation of national CIGs are therefore recommended.

Improvements in world-wide intercomparison of PV module calibration

OpenAIRE

Salis, E.; Pavanello, D.; Field, M.; Kräling, U.; Neuberger, F.; Kiefer, K.; Osterwald, C.; Rummel, S.; Levi, D.; Hishikawa, Y.; Yamagoe, K.; Ohshima, H.; Yoshita, M.; Müllejans, H.

2017-01-01

The calibration of the electrical performance for seven photovoltaic (PV) modules was compared between four reference laboratories on three continents. The devices included two samples in standard and two in high-efficiency crystalline silicon technology, two CI(G)S and one CdTe module. The reference value for each PV module parameter was calculated from the average of the results of all four laboratories, weighted by the respective measurement uncertainties. All single results were then anal...

Effectiveness of adjunctive antimicrobial photodynamic therapy in reducing peri-implant inflammatory response in individuals vaping electronic cigarettes: A randomized controlled clinical trial.

Science.gov (United States)

Al Rifaiy, Mohammed Q; Qutub, Osama A; Alasqah, Mohammed N; Al-Sowygh, Zeyad H; Mokeem, Sameer A; Alrahlah, Ali

2018-06-01

There are no studies that have assessed the effectiveness of antimicrobial photodynamic therapy (aPDT) in reducing peri-implant inflammatory response in individuals vaping electronic cigarettes (e-cigs). This study explored the effectiveness of aPDT as an adjunct to mechanical debridement (MD) in the treatment of peri-implant mucositis (p-iM) in individuals vaping e-cigs. Vaping individuals with p-iM were divided into 2 groups: (a) Group-I: receiving MD with aPDT (test group); and (b) Group-II: MD only (control group). Peri-implant inflammatory parameters including plaque index (PI), bleeding on probing (BoP), and pocket depth (PD) were assessed at baseline and 12-weeks follow-up. Inter- and intra-group comparisons were made using Mann-Whitney U test and Wilcoxon signed ranks test. P-value vaping individuals in groups I and II were 33.6 ± 2.8 and 35.4 ± 2.1 years, respectively. Mean daily frequency of vaping e-cigs in groups I and II was 7.3 ± 0.9 and 5.9 ± 1.0 whereas mean duration of vaping e-cigs was 4.8 ± 1.5 and 4.1 ± 1.3 years respectively. There was no significant difference between groups at baseline. There was significant improvement in PI (p vaping e-cigs. The findings of the present study should be considered preliminary and interpreted with caution. Further randomized clinical trials should be performed in order to obtain strong conclusions. Copyright © 2018 Elsevier B.V. All rights reserved.

A formal approach to the analysis of clinical computer-interpretable guideline modeling languages.

Science.gov (United States)

Grando, M Adela; Glasspool, David; Fox, John

2012-01-01

To develop proof strategies to formally study the expressiveness of workflow-based languages, and to investigate their applicability to clinical computer-interpretable guideline (CIG) modeling languages. We propose two strategies for studying the expressiveness of workflow-based languages based on a standard set of workflow patterns expressed as Petri nets (PNs) and notions of congruence and bisimilarity from process calculus. Proof that a PN-based pattern P can be expressed in a language L can be carried out semi-automatically. Proof that a language L cannot provide the behavior specified by a PNP requires proof by exhaustion based on analysis of cases and cannot be performed automatically. The proof strategies are generic but we exemplify their use with a particular CIG modeling language, PROforma. To illustrate the method we evaluate the expressiveness of PROforma against three standard workflow patterns and compare our results with a previous similar but informal comparison. We show that the two proof strategies are effective in evaluating a CIG modeling language against standard workflow patterns. We find that using the proposed formal techniques we obtain different results to a comparable previously published but less formal study. We discuss the utility of these analyses as the basis for principled extensions to CIG modeling languages. Additionally we explain how the same proof strategies can be reused to prove the satisfaction of patterns expressed in the declarative language CIGDec. The proof strategies we propose are useful tools for analysing the expressiveness of CIG modeling languages. This study provides good evidence of the benefits of applying formal methods of proof over semi-formal ones. Copyright © 2011 Elsevier B.V. All rights reserved.

Development of high-performance concrete having high resistance to chloride penetration

International Nuclear Information System (INIS)

Oh, Byung Hwan; Cha, Soo Won; Jang, Bong Seok; Jang, Seung Yup

2002-01-01

The resistance to chloride penetration is one of the simplest measures to determine the durability of concrete, e.g. resistance to freezing and thawing, corrosion of steel in concrete and other chemical attacks. Thus, high-performance concrete may be defined as the concrete having high resistance to chloride penetration as well as high strength. The purpose of this paper is to investigate the resistance to chloride penetration of different types of concrete and to develop high-performance concrete that has very high resistance to chloride penetration, and thus, can guarantee high durability. A large number of concrete specimens have been tested by the rapid chloride permeability test method as designated in AASHTO T 277 and ASTM C 1202. The major test variables include water-to-binder ratios, type of cement, type and amount of mineral admixtures (silica fume, fly ash and blast-furnace slag), maximum size of aggregates and air-entrainment. Test results show that concrete containing optimal amount of silica fume shows very high resistance to chloride penetration, and high-performance concrete developed in this study can be efficiently employed to enhance the durability of concrete structures in severe environments such as nuclear power plants, water-retaining structures and other offshore structures

Selective removal of CuIn1−xGaxSe2 absorber layer with no edge melting using a nanosecond Nd : YAG laser

International Nuclear Information System (INIS)

Lee, S H; Kim, C K; In, J H; Jeong, S H; Shim, H S

2013-01-01

This paper reports that selective removal of a CuIn 1−x Ga x Se 2 (CIGS) thin film on a Mo-coated glass substrate can be achieved with no edge melting or damage of the Mo layer using a nanosecond Nd : YAG laser with a wavelength of 1064 nm. It is shown that the two crucial parameters that determine the possibility of clean removal of only the CIGS layer are Ga concentration of the CIGS film and laser fluence. For CIGS films with Ga/(Ga+In) ratio greater than about 0.2 for which the band gap energy is close to or over the photon energy (1.17 eV), laser-induced thermal expansion proved to be the mechanism of film removal that drives an initial bulging of the film and then fracture into tens of micrometre sized fragments as observed in in situ shadowgraph images. The fracture-type removal of CIGS films was further verified by scanning electron micrographs of the craters showing that the original shapes of the CIGS polycrystals remain intact along the crater rim. A numerical simulation of film temperature under the irradiation conditions of selective removal was carried out to show that the magnitude of induced thermal stress within the film closely agreed to the yield strength of the CIGS thin film. The results confirmed that a nanosecond laser could be a better choice for P2 and P3 scribing of CIGS thin films if process conditions are properly determined. (paper)

Identifying High Performance ERP Projects

OpenAIRE

Stensrud, Erik; Myrtveit, Ingunn

2002-01-01

Learning from high performance projects is crucial for software process improvement. Therefore, we need to identify outstanding projects that may serve as role models. It is common to measure productivity as an indicator of performance. It is vital that productivity measurements deal correctly with variable returns to scale and multivariate data. Software projects generally exhibit variable returns to scale, and the output from ERP projects is multivariate. We propose to use Data Envelopment ...

A comparative study on charge carrier recombination across the junction region of Cu2ZnSn(S,Se4 and Cu(In,GaSe2 thin film solar cells

Directory of Open Access Journals (Sweden)

Mohammad Abdul Halim

2016-03-01

Full Text Available A comparative study with focusing on carrier recombination properties in Cu2ZnSn(S,Se4 (CZTSSe and the CuInGaSe2 (CIGS solar cells has been carried out. For this purpose, electroluminescence (EL and also bias-dependent time resolved photoluminescence (TRPL using femtosecond (fs laser source were performed. For the similar forward current density, the EL-intensity of the CZTSSe sample was obtained significantly lower than that of the CIGS sample. Primarily, it can be attributed to the existence of excess amount of non-radiative recombination center in the CZTSSe, and/or CZTSSe/CdS interface comparing to that of CIGS sample. In case of CIGS sample, TRPL decay time was found to increase with the application of forward-bias. This can be attributed to the reduced charge separation rate resulting from the reduced electric-field at the junction. However, in CZTSSe sample, TRPL decay time has been found almost independent under the forward and reverse-bias conditions. This phenomenon indicates that the charge recombination rate strongly dominates over the charge separation rate across the junction of the CZTSSe sample. Finally, temperature dependent VOC suggests that interface related recombination in the CZTSSe solar cell structure might be one of the major factors that affect EL-intensity and also, TRPL decay curves.

A comparative study on charge carrier recombination across the junction region of Cu{sub 2}ZnSn(S,Se){sub 4} and Cu(In,Ga)Se{sub 2} thin film solar cells

Energy Technology Data Exchange (ETDEWEB)

Halim, Mohammad Abdul, E-mail: halimtsukuba2012@gmail.com; Islam, Muhammad Monirul; Luo, Xianjia; Sakurai, Takeaki; Akimoto, Katsuhiro [Institute of Applied Physics, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); Sakai, Noriyuki; Kato, Takuya; Sugimoto, Hiroki [Energy Solution Business Center, Showa Shell Sekiyu K.K., Minato, Tokyo 135-8074 (Japan); Tampo, Hitoshi; Shibata, Hajime; Niki, Shigeru [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Ibaraki 305-8568 (Japan)

2016-03-15

A comparative study with focusing on carrier recombination properties in Cu{sub 2}ZnSn(S,Se){sub 4} (CZTSSe) and the CuInGaSe{sub 2} (CIGS) solar cells has been carried out. For this purpose, electroluminescence (EL) and also bias-dependent time resolved photoluminescence (TRPL) using femtosecond (fs) laser source were performed. For the similar forward current density, the EL-intensity of the CZTSSe sample was obtained significantly lower than that of the CIGS sample. Primarily, it can be attributed to the existence of excess amount of non-radiative recombination center in the CZTSSe, and/or CZTSSe/CdS interface comparing to that of CIGS sample. In case of CIGS sample, TRPL decay time was found to increase with the application of forward-bias. This can be attributed to the reduced charge separation rate resulting from the reduced electric-field at the junction. However, in CZTSSe sample, TRPL decay time has been found almost independent under the forward and reverse-bias conditions. This phenomenon indicates that the charge recombination rate strongly dominates over the charge separation rate across the junction of the CZTSSe sample. Finally, temperature dependent V{sub OC} suggests that interface related recombination in the CZTSSe solar cell structure might be one of the major factors that affect EL-intensity and also, TRPL decay curves.

Integrated plasma control for high performance tokamaks

International Nuclear Information System (INIS)

Humphreys, D.A.; Deranian, R.D.; Ferron, J.R.; Johnson, R.D.; LaHaye, R.J.; Leuer, J.A.; Penaflor, B.G.; Walker, M.L.; Welander, A.S.; Jayakumar, R.J.; Makowski, M.A.; Khayrutdinov, R.R.

2005-01-01

Sustaining high performance in a tokamak requires controlling many equilibrium shape and profile characteristics simultaneously with high accuracy and reliability, while suppressing a variety of MHD instabilities. Integrated plasma control, the process of designing high-performance tokamak controllers based on validated system response models and confirming their performance in detailed simulations, provides a systematic method for achieving and ensuring good control performance. For present-day devices, this approach can greatly reduce the need for machine time traditionally dedicated to control optimization, and can allow determination of high-reliability controllers prior to ever producing the target equilibrium experimentally. A full set of tools needed for this approach has recently been completed and applied to present-day devices including DIII-D, NSTX and MAST. This approach has proven essential in the design of several next-generation devices including KSTAR, EAST, JT-60SC, and ITER. We describe the method, results of design and simulation tool development, and recent research producing novel approaches to equilibrium and MHD control in DIII-D. (author)

Highlighting High Performance: Blackstone Valley Regional Vocational Technical High School; Upton, Massachusetts

Energy Technology Data Exchange (ETDEWEB)

2006-10-01

This brochure describes the key high-performance building features of the Blackstone Valley High School. The brochure was paid for by the Massachusetts Technology Collaborative as part of their Green Schools Initiative. High-performance features described are daylighting and energy-efficient lighting, indoor air quality, solar energy, building envelope, heating and cooling systems, and water conservation. Energy cost savings are also discussed.

Ground Glass Pozzolan in Conventional, High, and Ultra-High Performance Concrete

Directory of Open Access Journals (Sweden)

Tagnit-Hamou Arezki

2018-01-01

Full Text Available Ground-glass pozzolan (G obtained by grinding the mixed-waste glass to same fineness of cement can act as a supplementary-cementitious material (SCM, given that it is an amorphous and a pozzolanic material. The G showed promising performances in different concrete types such as conventional concrete (CC, high-performance concrete (HPC, and ultra-high performance concrete (UHPC. The current paper reports on the characteristics and performance of G in these concrete types. The use of G provides several advantages (technological, economical, and environmental. It reduces the production cost of concrete and decrease the carbon footprint of a traditional concrete structures. The rheology of fresh concrete can be improved due to the replacement of cement by non-absorptive glass particles. Strength and rigidity improvements in the concrete containing G are due to the fact that glass particles act as inclusions having a very high strength and elastic modulus that have a strengthening effect on the overall hardened matrix.

Progress on Low-Temperature Pulsed Electron Deposition of CuInGaSe2 Solar Cells

Directory of Open Access Journals (Sweden)

Massimo Mazzer

2016-03-01

Full Text Available The quest for single-stage deposition of CuInGaSe2 (CIGS is an open race to replace very effective but capital intensive thin film solar cell manufacturing processes like multiple-stage coevaporation or sputtering combined with high pressure selenisation treatments. In this paper the most recent achievements of Low Temperature Pulsed Electron Deposition (LTPED, a novel single stage deposition process by which CIGS can be deposited at 250 °C, are presented and discussed. We show that selenium loss during the film deposition is not a problem with LTPED as good crystalline films are formed very close to the melting temperature of selenium. The mechanism of formation of good ohmic contacts between CIGS and Mo in the absence of any MoSe2 transition layers is also illustrated, followed by a brief summary of the measured characteristics of test solar cells grown by LTPED. The 17% efficiency target achieved by lab-scale CIGS devices without bandgap modulation, antireflection coating or K-doping is considered to be a crucial milestone along the path to the industrial scale-up of LTPED. The paper ends with a brief review of the open scientific and technological issues related to the scale-up and the possible future applications of the new technology.

Mood states and motor performance: a study with high performance voleybol athletes

Directory of Open Access Journals (Sweden)

Lenamar Fiorese Vieira

2008-07-01

Full Text Available http://dx.doi.org/10.5007/1980-0037.2008v10n1p62 The objective of this research was to investigate the relationship between the sporting performance and mood states of high performance volleyball athletes. Twenty-three adult athletes of both sexes were assessed. The measurement instrument adopted was the POMS questionnaire. Data collection was carried out individually during the state championships. Dada were analyzed using descriptive statistics; the Friedman test for analysis of variance and the Mann-Whitney test for differences between means. The results demonstrated that both teams exhibited the mood state profi le corresponding to the “iceberg” profile. In the male team, vigor remained constant throughout all phases of the competition, while in the female team this element was unstable. The male team’s fatigue began low, during the training phase, with rates that rose as the competition progressed, with statistically significant differences between the fi rst and last matches the team played. In the female team, the confusion factor, which was at a high level during training, reduced progressively throughout the competition, with a difference that was signifi cant to p ≤ 0.05. With relation to performance and mood profi le, the female team exhibited statistically significant differences between the mean vigor and fatigue factors of high and low performance athletes. It is therefore concluded that the mood state profi le is a factor that impacts on the motor performance of these high performance teams.

High performance leadership in unusually challenging educational circumstances

Directory of Open Access Journals (Sweden)

Andy Hargreaves

2015-04-01

Full Text Available This paper draws on findings from the results of a study of leadership in high performing organizations in three sectors. Organizations were sampled and included on the basis of high performance in relation to no performance, past performance, performance among similar peers and performance in the face of limited resources or challenging circumstances. The paper concentrates on leadership in four schools that met the sample criteria.  It draws connections to explanations of the high performance ofEstoniaon the OECD PISA tests of educational achievement. The article argues that leadership in these four schools that performed above expectations comprised more than a set of competencies. Instead, leadership took the form of a narrative or quest that pursued an inspiring dream with relentless determination; took improvement pathways that were more innovative than comparable peers; built collaboration and community including with competing schools; and connected short-term success to long-term sustainability.

Hydrogen effects on deep level defects in proton implanted Cu(In,Ga)Se{sub 2} based thin films

Energy Technology Data Exchange (ETDEWEB)

Lee, D.W.; Seol, M.S.; Kwak, D.W.; Oh, J.S. [Department of Physics, Dongguk University, Seoul 100-715 (Korea, Republic of); Jeong, J.H. [Photo-electronic Hybrids Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Cho, H.Y., E-mail: hycho@dongguk.edu [Department of Physics, Dongguk University, Seoul 100-715 (Korea, Republic of)

2012-08-01

Hydrogen effects on deep level defects and a defect generation in proton implanted Cu(In,Ga)Se{sub 2} (CIGS) based thin films for solar cell were investigated. CIGS films with a thickness of 3 {mu}m were grown on a soda-lime glass substrate by a co-evaporation method, and then were implanted with protons. To study deep level defects in the proton implanted CIGS films, deep level transient spectroscopy measurements on the CIGS-based solar cells were carried out, these measurements found 6 traps (including 3 hole traps and 3 electron traps). In the proton implanted CIGS films, the deep level defects, which are attributed to the recombination centers of the CIGS solar cell, were significantly reduced in intensity, while a deep level defect was generated around 0.28 eV above the valence band maximum. Therefore, we suggest that most deep level defects in CIGS films can be controlled by hydrogen effects. - Highlights: Black-Right-Pointing-Pointer Proton implanted Cu(In,Ga)Se{sub 2} thin film and solar cell are prepared. Black-Right-Pointing-Pointer Deep level defects of Cu(In,Ga)Se{sub 2} thin film and solar cell are investigated. Black-Right-Pointing-Pointer Hydrogenation using proton implantation and H{sub 2} annealing reduces deep level defects. Black-Right-Pointing-Pointer Hydrogenation could enhance electrical properties and efficiency of solar cells.

Oxide nanoparticle-based fabrication and optical properties of Cu(In{sub 1−x}Ga{sub x})S{sub 2} absorber layer for solar cells

Energy Technology Data Exchange (ETDEWEB)

Choi, Yo-Min [Department of Fusion Chemical Engineering, Hanyang University, Ansan 426-791 (Korea, Republic of); Lee, Young-In [Institute of Nanosensor Technology, Hanyang University, Ansan 426-791 (Korea, Republic of); Kim, Bum-Sung [Production Technology R and D Division, Korea Institute of Industrial Technology, Incheon 406-840 (Korea, Republic of); Choa, Yong-Ho, E-mail: choa15@hanyang.ac.kr [Department of Fusion Chemical Engineering, Hanyang University, Ansan 426-791 (Korea, Republic of); Institute of Nanosensor Technology, Hanyang University, Ansan 426-791 (Korea, Republic of)

2013-11-01

The compound Cu(In{sub 1−x}Ga{sub x})S{sub 2} (CIGS) was synthesized using copper oxide, indium oxide and gallium oxide mixture (CIGO) nanoparticles using salt-assisted ultrasonic spray pyrolysis (SAUSP). Under this method, CIGS can be produced without the complicated restrictions of a vacuum and an inert atmosphere. The band gap of CIGS can be controlled by introducing the desired stoichiometric quantities of starting materials. In order to synthesize CIGO nanoparticles, various NaCl/precursor ratios were used to accomplish the SAUSP process and ultimately monodisperse CIGO nanoparticles with average particle size of 9 nm without hard agglomeration were obtained. Subsequently, the CIGO nanoparticles were sulfurized to form the CIGS in H{sub 2}S/Ar atmosphere at 500 °C. The CIGS obtained in the present study has the various band gap ranging from 1.67 to 2.34 eV depending on the Ga / (In + Ga) ratio, and those band gap correspond to the respective bulk materials. - Highlights: • CIGS is obtained using Cu, In and Ga oxide mixture (CIGO) nanoparticles. • Salt-assisted ultrasonic spray pyrolysis is used to synthesize CIGO nanoparticles. • Nine nanometers of monodisperse CIGO nanoparticles without hard agglomeration is obtained. • The band gap of CIGS can be controlled by introducing the desired ratio of precursor.

High-performance computing in seismology

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

The scientific, technical, and economic importance of the issues discussed here presents a clear agenda for future research in computational seismology. In this way these problems will drive advances in high-performance computing in the field of seismology. There is a broad community that will benefit from this work, including the petroleum industry, research geophysicists, engineers concerned with seismic hazard mitigation, and governments charged with enforcing a comprehensive test ban treaty. These advances may also lead to new applications for seismological research. The recent application of high-resolution seismic imaging of the shallow subsurface for the environmental remediation industry is an example of this activity. This report makes the following recommendations: (1) focused efforts to develop validated documented software for seismological computations should be supported, with special emphasis on scalable algorithms for parallel processors; (2) the education of seismologists in high-performance computing technologies and methodologies should be improved; (3) collaborations between seismologists and computational scientists and engineers should be increased; (4) the infrastructure for archiving, disseminating, and processing large volumes of seismological data should be improved.

High performance flexible CMOS SOI FinFETs

KAUST Repository

Fahad, Hossain M.

2014-06-01

We demonstrate the first ever CMOS compatible soft etch back based high performance flexible CMOS SOI FinFETs. The move from planar to non-planar FinFETs has enabled continued scaling down to the 14 nm technology node. This has been possible due to the reduction in off-state leakage and reduced short channel effects on account of the superior electrostatic charge control of multiple gates. At the same time, flexible electronics is an exciting expansion opportunity for next generation electronics. However, a fully integrated low-cost system will need to maintain ultra-large-scale-integration density, high performance and reliability - same as today\\'s traditional electronics. Up until recently, this field has been mainly dominated by very weak performance organic electronics enabled by low temperature processes, conducive to low melting point plastics. Now however, we show the world\\'s highest performing flexible version of 3D FinFET CMOS using a state-of-the-art CMOS compatible fabrication technique for high performance ultra-mobile consumer applications with stylish design. © 2014 IEEE.

Architecting Web Sites for High Performance

Directory of Open Access Journals (Sweden)

Arun Iyengar

2002-01-01

Full Text Available Web site applications are some of the most challenging high-performance applications currently being developed and deployed. The challenges emerge from the specific combination of high variability in workload characteristics and of high performance demands regarding the service level, scalability, availability, and costs. In recent years, a large body of research has addressed the Web site application domain, and a host of innovative software and hardware solutions have been proposed and deployed. This paper is an overview of recent solutions concerning the architectures and the software infrastructures used in building Web site applications. The presentation emphasizes three of the main functions in a complex Web site: the processing of client requests, the control of service levels, and the interaction with remote network caches.

High efficiency Cu(In,Ga)Se{sub 2} thin film solar cells without intermediate buffer layers

Energy Technology Data Exchange (ETDEWEB)

Ramanathan, K.; Wiesner, H.; Asher, S.; Niles, D.; Bhattacharya, R.N.; Keane, J.; Contreras, M.A.; Noufi, R. [National Renewable Energy Lab., Golden, CO (United States). Electronic Materials and Devices Div.

1998-09-01

The nature of the interface between CuInGaSe{sub 2} (CIGS) and the chemical bath deposited CdS layer has been investigated. The authors show that heat-treating the absorbers in Cd- or Zn-containing solutions in the presence of ammonium hydroxide sets up an interfacial reaction with the possibility of an ion exchange occurring between Cd and Cu. The characteristics of devices made in this manner suggest that the reaction generates a thin, n-doped region in the absorber. The authors suggest that this aspect might be more important than the CdS layer in the formation of the junction. It is quite possible that the CdS/CuInSe{sub 2} device is a buried, shallow junction with a CdS window layer, rather than a heterojunction between CdS and CIGS. The authors use these ideas to develop methods for fabricating diodes without CdS or Cd.

Development of a high performance liquid chromatography method ...

African Journals Online (AJOL)

Development of a high performance liquid chromatography method for simultaneous ... Purpose: To develop and validate a new low-cost high performance liquid chromatography (HPLC) method for ..... Several papers have reported the use of ...

Toward a theory of high performance.

Science.gov (United States)

Kirby, Julia

2005-01-01

What does it mean to be a high-performance company? The process of measuring relative performance across industries and eras, declaring top performers, and finding the common drivers of their success is such a difficult one that it might seem a fool's errand to attempt. In fact, no one did for the first thousand or so years of business history. The question didn't even occur to many scholars until Tom Peters and Bob Waterman released In Search of Excellence in 1982. Twenty-three years later, we've witnessed several more attempts--and, just maybe, we're getting closer to answers. In this reported piece, HBR senior editor Julia Kirby explores why it's so difficult to study high performance and how various research efforts--including those from John Kotter and Jim Heskett; Jim Collins and Jerry Porras; Bill Joyce, Nitin Nohria, and Bruce Roberson; and several others outlined in a summary chart-have attacked the problem. The challenge starts with deciding which companies to study closely. Are the stars the ones with the highest market caps, the ones with the greatest sales growth, or simply the ones that remain standing at the end of the game? (And when's the end of the game?) Each major study differs in how it defines success, which companies it therefore declares to be worthy of emulation, and the patterns of activity and attitude it finds in common among them. Yet, Kirby concludes, as each study's method incrementally solves problems others have faced, we are progressing toward a consensus theory of high performance.

Development of high performance cladding materials

International Nuclear Information System (INIS)

Park, Jeong Yong; Jeong, Y. H.; Park, S. Y.

2010-04-01

The irradiation test for HANA claddings conducted and a series of evaluation for next-HANA claddings as well as their in-pile and out-of pile performances tests were also carried out at Halden research reactor. The 6th irradiation test have been completed successfully in Halden research reactor. As a result, HANA claddings showed high performance, such as corrosion resistance increased by 40% compared to Zircaloy-4. The high performance of HANA claddings in Halden test has enabled lead test rod program as the first step of the commercialization of HANA claddings. DB has been established for thermal and LOCA-related properties. It was confirmed from the thermal shock test that the integrity of HANA claddings was maintained in more expanded region than the criteria regulated by NRC. The manufacturing process of strips was established in order to apply HANA alloys, which were originally developed for the claddings, to the spacer grids. 250 kinds of model alloys for the next-generation claddings were designed and manufactured over 4 times and used to select the preliminary candidate alloys for the next-generation claddings. The selected candidate alloys showed 50% better corrosion resistance and 20% improved high temperature oxidation resistance compared to the foreign advanced claddings. We established the manufacturing condition controlling the performance of the dual-cooled claddings by changing the reduction rate in the cold working steps

The Formation Mechanism of Cu(In0.7Ga0.3Se2 Nanoparticles and the Densification Trajectory of the Se-Rich Quaternary Target by Hot Pressing

Directory of Open Access Journals (Sweden)

Qiang Ma

2018-03-01

Full Text Available In this paper, a method to obtain the CuInGaSe2 (CIGS absorber layer with an appropriate selenium content is put forward, in which a Se-rich target is used to deposit a CIGS thin-film and this film is annealed in a Se-free inert atmosphere. The key issue of this method is the preparation of a Se-rich target with a homogeneous composition and a high-density. The formation mechanism of CuInSe2 and CuGaSe2 is investigated and the results point to the intermediate phase Cu2−xSe playing a role of a nucleation core. The sintering densification trajectory of the target with the addition of extra selenium is researched. Additionally, an effective way to avoid the sintering defects is proposed. Finally, a conversion efficiency of 11.2% for the CIGS solar cell is reached by sputtering from the obtained Se-rich target.

High performance computing in Windows Azure cloud

OpenAIRE

Ambruš, Dejan

2013-01-01

High performance, security, availability, scalability, flexibility and lower costs of maintenance have essentially contributed to the growing popularity of cloud computing in all spheres of life, especially in business. In fact cloud computing offers even more than this. With usage of virtual computing clusters a runtime environment for high performance computing can be efficiently implemented also in a cloud. There are many advantages but also some disadvantages of cloud computing, some ...

High Performance Work System, HRD Climate and Organisational Performance: An Empirical Study

Science.gov (United States)

Muduli, Ashutosh

2015-01-01

Purpose: This paper aims to study the relationship between high-performance work system (HPWS) and organizational performance and to examine the role of human resource development (HRD) Climate in mediating the relationship between HPWS and the organizational performance in the context of the power sector of India. Design/methodology/approach: The…

The effect of electronic cigarette and tobacco smoke exposure on COPD bronchial epithelial cell inflammatory responses

Directory of Open Access Journals (Sweden)

Higham A

2018-03-01

Full Text Available Andrew Higham,1,2 Declan Bostock,1 George Booth,2 Josiah V Dungwa,2 Dave Singh1,2 1Division of Infection, Immunity and Respiratory Medicine, School of Biological Sciences, Faculty of Biology, Medicine and Health, Manchester Academic Health Science Centre, The University of Manchester and University Hospital of South Manchester, NHS Foundation Trust, Manchester, UK; 2Medicines Evaluation Unit, University Hospital of South Manchester, Manchester, UK Background: Electronic cigarettes (e-cigs are used to help smoking cessation. However, these devices contain harmful chemicals, and there are safety concerns. We have investigated the effects of e-cigs on the inflammatory response and viability of COPD bronchial epithelial cells (BECs.Methods: BECs from COPD patients and controls were exposed to e-cig vapor extract (ECVE and the levels of interleukin (IL-6, C-X-C motif ligand 8 (CXCL8, and lactate dehydrogenase release were measured. We also examined the effect of ECVE pretreatment on polyinosinic:polycytidylic acid (poly I:C-stimulated cytokine release from BECs. Parallel experiments using Calu-3 cells were performed. Comparisons were made with cigarette smoke extract (CSE.Results: ECVE and CSE caused an increase in the release of IL-6 and CXCL8 from Calu-3 cells. ECVE only caused toxicity in BECs and Calu-3 cells. Furthermore, ECVE and CSE dampened poly I:C-stimulated C-X-C motif ligand 10 release from both cell culture models, reaching statistical significance for CSE at an optical density of 0.3.Conclusion: ECVE caused toxicity and reduced the antiviral response to poly I:C. This raises concerns over the safety of e-cig use. Keywords: e-cigs, epithelial cells, COPD, air–liquid interface, cigarette smoke

Knowledge on Irradiation, Medical Imaging Prescriptions, and Clinical Imaging Referral Guidelines among Physicians in a Sub-Saharan African Country (Cameroon

Directory of Open Access Journals (Sweden)

Boniface Moifo

2017-01-01

Full Text Available Background. Clinical imaging guidelines (CIGs are suitable tools to enhance justification of imaging procedures. Objective. To assess physicians’ knowledge on irradiation, their self-perception of imaging prescriptions, and the use of CIGs. Materials and Methods. A questionnaire of 21 items was self-administered between July and August 2016 to 155 referring physicians working in seven university-affiliated hospitals in Yaoundé and Douala (Cameroon. This pretested questionnaire based on imaging referral practices, the use and the need of CIGs, knowledge on radiation doses of 11 specific radiologic procedures, and knowledge of injurious effects of radiation was completed in the presence of the investigator. Scores were allocated for each question. Results. 155 questionnaires were completed out of 180 administered (86.1%. Participants were 90 (58% females, 63 (40.64% specialists, 53 (34.20% residents/interns, and 39 (25.16% general practitioners. The average professional experience was 7.4 years (1–25 years. The mean knowledge score was 11.5/59 with no influence of sex, years of experience, and professional category. CIGs users’ score was better than nonusers (means 14.2 versus 10.6; p<0.01. 80% of physicians (124/155 underrated radiation doses of routine imaging exams. Seventy-eight (50.3% participants have knowledge on CIGs and half of them made use of them. “Impact on diagnosis” was the highest justification criteria follow by “impact on treatment decision.” Unjustified requests were mainly for “patient expectation or will” or for “research motivations.” 96% of interviewees believed that making available national CIGs will improve justification. Conclusion. Most physicians did not have appropriate awareness about radiation doses for routine imaging procedures. A small number of physicians have knowledge on CIGs but they believe that making available CIGs will improve justification of imaging procedures. Continuous

Governance among Malaysian high performing companies

Directory of Open Access Journals (Sweden)

Asri Marsidi

2016-07-01

Full Text Available Well performed companies have always been linked with effective governance which is generally reflected through effective board of directors. However many issues concerning the attributes for effective board of directors remained unresolved. Nowadays diversity has been perceived as able to influence the corporate performance due to the likelihood of meeting variety of needs and demands from diverse customers and clients. The study therefore aims to provide a fundamental understanding on governance among high performing companies in Malaysia.

Powder metallurgical high performance materials. Proceedings. Volume 1: high performance P/M metals

International Nuclear Information System (INIS)

Kneringer, G.; Roedhammer, P.; Wildner, H.

2001-01-01

The proceedings of this sequence of seminars form an impressive chronicle of the continued progress in the understanding of refractory metals and cemented carbides and in their manufacture and application. There the ingenuity and assiduous work of thousands of scientists and engineers striving for progress in the field of powder metallurgy is documented in more than 2000 contributions covering some 30000 pages. The 15th Plansee Seminar was convened under the general theme 'Powder Metallurgical High Performance Materials'. Under this broadened perspective the seminar will strive to look beyond the refractory metals and cemented carbides, which remain at its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. (author)

Powder metallurgical high performance materials. Proceedings. Volume 1: high performance P/M metals

Energy Technology Data Exchange (ETDEWEB)

Kneringer, G; Roedhammer, P; Wildner, H [eds.

2001-07-01

The proceedings of this sequence of seminars form an impressive chronicle of the continued progress in the understanding of refractory metals and cemented carbides and in their manufacture and application. There the ingenuity and assiduous work of thousands of scientists and engineers striving for progress in the field of powder metallurgy is documented in more than 2000 contributions covering some 30000 pages. The 15th Plansee Seminar was convened under the general theme 'Powder Metallurgical High Performance Materials'. Under this broadened perspective the seminar will strive to look beyond the refractory metals and cemented carbides, which remain at its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. (author)

High-Speed, High-Performance DQPSK Optical Links with Reduced Complexity VDFE Equalizers

Directory of Open Access Journals (Sweden)

Maki Nanou

2017-02-01

Full Text Available Optical transmission technologies optimized for optical network segments sensitive to power consumption and cost, comprise modulation formats with direct detection technologies. Specifically, non-return to zero differential quaternary phase shift keying (NRZ-DQPSK in deployed fiber plants, combined with high-performance, low-complexity electronic equalizers to compensate residual impairments at the receiver end, can be proved as a viable solution for high-performance, high-capacity optical links. Joint processing of the constructive and the destructive signals at the single-ended DQPSK receiver provides improved performance compared to the balanced configuration, however, at the expense of higher hardware requirements, a fact that may not be neglected especially in the case of high-speed optical links. To overcome this bottleneck, the use of partially joint constructive/destructive DQPSK equalization is investigated in this paper. Symbol-by-symbol equalization is performed by means of Volterra decision feedback-type equalizers, driven by a reduced subset of signals selected from the constructive and the destructive ports of the optical detectors. The proposed approach offers a low-complexity alternative for electronic equalization, without sacrificing much of the performance compared to the fully-deployed counterpart. The efficiency of the proposed equalizers is demonstrated by means of computer simulation in a typical optical transmission scenario.

Design of JMTR high-performance fuel element

International Nuclear Information System (INIS)

Sakurai, Fumio; Shimakawa, Satoshi; Komori, Yoshihiro; Tsuchihashi, Keiichiro; Kaminaga, Fumito

1999-01-01

For test and research reactors, the core conversion to low-enriched uranium fuel is required from the viewpoint of non-proliferation of nuclear weapon material. Improvements of core performance are also required in order to respond to recent advanced utilization needs. In order to meet both requirements, a high-performance fuel element of high uranium density with Cd wires as burnable absorbers was adopted for JMTR core conversion to low-enriched uranium fuel. From the result of examination of an adaptability of a few group constants generated by a conventional transport-theory calculation with an isotropic scattering approximation to a few group diffusion-theory core calculation for design of the JMTR high-performance fuel element, it was clear that the depletion of Cd wires was not able to be predicted accurately using group constants generated by the conventional method. Therefore, a new generation method of a few group constants in consideration of an incident neutron spectrum at Cd wire was developed. As the result, the most suitable high-performance fuel element for JMTR was designed successfully, and that allowed extension of operation duration without refueling to almost twice as long and offer of irradiation field with constant neutron flux. (author)

ELMs IN DIII-D HIGH PERFORMANCE DISCHARGES

International Nuclear Information System (INIS)

TURNBULL, A.D; LAO, L.L; OSBORNE, T.H; SAUTER, O; STRAIT, E.J; TAYLOR, T.S; CHU, M.S; FERRON, J.R; GREENFIELD, C.M; LEONARD, A.W; MILLER, R.L; SNYDER, P.B; WILSON, H.R; ZOHM, H

2003-01-01

A new understanding of edge localized modes (ELMs) in tokamak discharges is emerging [P.B. Snyder, et al., Phys. Plasmas, 9, 2037 (2002)], in which the ELM is an essentially ideal magnetohydrodynamic (MHD) instability and the ELM severity is determined by the radial width of the linearly unstable MHD kink modes. A detailed, comparative study of the penetration into the core of the respective linear instabilities in a standard DIII-D ELMing, high confinement mode (H-mode) discharge, with that for two relatively high performance discharges shows that these are also encompassed within the framework of the new model. These instabilities represent the key, limiting factor in extending the high performance of these discharges. In the standard ELMing H-mode, the MHD instabilities are highly localized in the outer few percent flux surfaces and the ELM is benign, causing only a small temporary drop in the energy confinement. In contrast, for both a very high confinement mode (VH-mode) and an H-mode with a broad internal transport barrier (ITB) extending over the entire core and coalesced with the edge transport barrier, the linearly unstable modes penetrate well into the mid radius and the corresponding consequences for global confinement are significantly more severe. The ELM accordingly results in an irreversible loss of the high performance

The path toward HEP High Performance Computing

CERN Document Server

Apostolakis, John; Carminati, Federico; Gheata, Andrei; Wenzel, Sandro

2014-01-01

High Energy Physics code has been known for making poor use of high performance computing architectures. Efforts in optimising HEP code on vector and RISC architectures have yield limited results and recent studies have shown that, on modern architectures, it achieves a performance between 10% and 50% of the peak one. Although several successful attempts have been made to port selected codes on GPUs, no major HEP code suite has a 'High Performance' implementation. With LHC undergoing a major upgrade and a number of challenging experiments on the drawing board, HEP cannot any longer neglect the less-than-optimal performance of its code and it has to try making the best usage of the hardware. This activity is one of the foci of the SFT group at CERN, which hosts, among others, the Root and Geant4 project. The activity of the experiments is shared and coordinated via a Concurrency Forum, where the experience in optimising HEP code is presented and discussed. Another activity is the Geant-V project, centred on th...

3D printed high performance strain sensors for high temperature applications

Science.gov (United States)

Rahman, Md Taibur; Moser, Russell; Zbib, Hussein M.; Ramana, C. V.; Panat, Rahul

2018-01-01

Realization of high temperature physical measurement sensors, which are needed in many of the current and emerging technologies, is challenging due to the degradation of their electrical stability by drift currents, material oxidation, thermal strain, and creep. In this paper, for the first time, we demonstrate that 3D printed sensors show a metamaterial-like behavior, resulting in superior performance such as high sensitivity, low thermal strain, and enhanced thermal stability. The sensors were fabricated using silver (Ag) nanoparticles (NPs), using an advanced Aerosol Jet based additive printing method followed by thermal sintering. The sensors were tested under cyclic strain up to a temperature of 500 °C and showed a gauge factor of 3.15 ± 0.086, which is about 57% higher than that of those available commercially. The sensor thermal strain was also an order of magnitude lower than that of commercial gages for operation up to a temperature of 500 °C. An analytical model was developed to account for the enhanced performance of such printed sensors based on enhanced lateral contraction of the NP films due to the porosity, a behavior akin to cellular metamaterials. The results demonstrate the potential of 3D printing technology as a pathway to realize highly stable and high-performance sensors for high temperature applications.

High performance carbon nanocomposites for ultracapacitors

Science.gov (United States)

Lu, Wen

2012-10-02

The present invention relates to composite electrodes for electrochemical devices, particularly to carbon nanotube composite electrodes for high performance electrochemical devices, such as ultracapacitors.

High-Performance Java Codes for Computational Fluid Dynamics

Science.gov (United States)

Riley, Christopher; Chatterjee, Siddhartha; Biswas, Rupak; Biegel, Bryan (Technical Monitor)

2001-01-01

The computational science community is reluctant to write large-scale computationally -intensive applications in Java due to concerns over Java's poor performance, despite the claimed software engineering advantages of its object-oriented features. Naive Java implementations of numerical algorithms can perform poorly compared to corresponding Fortran or C implementations. To achieve high performance, Java applications must be designed with good performance as a primary goal. This paper presents the object-oriented design and implementation of two real-world applications from the field of Computational Fluid Dynamics (CFD): a finite-volume fluid flow solver (LAURA, from NASA Langley Research Center), and an unstructured mesh adaptation algorithm (2D_TAG, from NASA Ames Research Center). This work builds on our previous experience with the design of high-performance numerical libraries in Java. We examine the performance of the applications using the currently available Java infrastructure and show that the Java version of the flow solver LAURA performs almost within a factor of 2 of the original procedural version. Our Java version of the mesh adaptation algorithm 2D_TAG performs within a factor of 1.5 of its original procedural version on certain platforms. Our results demonstrate that object-oriented software design principles are not necessarily inimical to high performance.

Application of a substrate bias to control the droplet density on Cu(In,Ga)Se{sub 2} thin films grown by Pulsed Electron Deposition

Energy Technology Data Exchange (ETDEWEB)

Rampino, S. [IMEM-CNR Institute, Parco Area delle Scienze 37/A, 43124 Parma (Italy); Pattini, F., E-mail: rampino@imem.cnr.it [IMEM-CNR Institute, Parco Area delle Scienze 37/A, 43124 Parma (Italy); Malagù, C.; Pozzetti, L. [Department of Physics and Earth Sciences, University of Ferrara, Via Saragat, 1-44122 Ferrara (Italy); Stefancich, M. [LENS Laboratory, Masdar Institute of Science and Technology, Masdar City, PO Box 54224, Abu Dhabi (United Arab Emirates); Bronzoni, M. [IMEM-CNR Institute, Parco Area delle Scienze 37/A, 43124 Parma (Italy)

2014-07-01

One of the main shortcomings in the fabrication of thin-film solar cells by pulsed high-energy deposition techniques (i.e. Pulsed Laser Deposition or Pulsed Electron Deposition — PED), is the presence of a significant number of particulates on the film surface. This affects the morphological properties of the cell active layers and, ultimately, the performance of the final device. To reduce the density of these defects, we deposited a Cu(In,Ga)Se{sub 2} (CIGS) thin film by PED and studied the effect on the film morphology when a DC bias was applied between the substrate and the target. Our results show that a negative substrate voltage, comprised between 0 and − 300 V, can not only reduce the droplet density on the CIGS film surface of about one order of magnitude with respect to the standard unbiased case (from 6 × 10{sup 5} to 5 × 10{sup 4} cm{sup −2}), but also lower the maximum particulate size and the surface smoothness. When a positive voltage is applied, we observed that a significant increase in the droplet surface density (up to 10{sup 8} cm{sup −2}) occurs. The abrupt change in the preferred crystal orientation (switching from (112) to (220)/(204) by applying negative and positive biases, respectively) is also a direct consequence of the applied DC voltage. These results confirm that the external DC bias could be used as an additional parameter to control the physical properties of thin films grown by PED. - Highlights: • Cu(In,Ga)Se{sub 2} (CIGS) films were grown by Pulsed Electron Deposition (PED). • Positive and negative DC biases were applied between the target and the substrate. • The droplet density can be reduced by one order of magnitude by DC negative bias. • Chemical composition and grain orientation of CIGS are influenced by the DC bias. • The DC bias can be an additional parameter of PED for controlling the film properties.

Strategy Guideline: Partnering for High Performance Homes

Energy Technology Data Exchange (ETDEWEB)

Prahl, D.

2013-01-01

High performance houses require a high degree of coordination and have significant interdependencies between various systems in order to perform properly, meet customer expectations, and minimize risks for the builder. Responsibility for the key performance attributes is shared across the project team and can be well coordinated through advanced partnering strategies. For high performance homes, traditional partnerships need to be matured to the next level and be expanded to all members of the project team including trades, suppliers, manufacturers, HERS raters, designers, architects, and building officials as appropriate. In an environment where the builder is the only source of communication between trades and consultants and where relationships are, in general, adversarial as opposed to cooperative, the chances of any one building system to fail are greater. Furthermore, it is much harder for the builder to identify and capitalize on synergistic opportunities. Partnering can help bridge the cross-functional aspects of the systems approach and achieve performance-based criteria. Critical success factors for partnering include support from top management, mutual trust, effective and open communication, effective coordination around common goals, team building, appropriate use of an outside facilitator, a partnering charter progress toward common goals, an effective problem-solving process, long-term commitment, continuous improvement, and a positive experience for all involved.

Quantum Accelerators for High-performance Computing Systems

Energy Technology Data Exchange (ETDEWEB)

Humble, Travis S. [ORNL; Britt, Keith A. [ORNL; Mohiyaddin, Fahd A. [ORNL

2017-11-01

We define some of the programming and system-level challenges facing the application of quantum processing to high-performance computing. Alongside barriers to physical integration, prominent differences in the execution of quantum and conventional programs challenges the intersection of these computational models. Following a brief overview of the state of the art, we discuss recent advances in programming and execution models for hybrid quantum-classical computing. We discuss a novel quantum-accelerator framework that uses specialized kernels to offload select workloads while integrating with existing computing infrastructure. We elaborate on the role of the host operating system to manage these unique accelerator resources, the prospects for deploying quantum modules, and the requirements placed on the language hierarchy connecting these different system components. We draw on recent advances in the modeling and simulation of quantum computing systems with the development of architectures for hybrid high-performance computing systems and the realization of software stacks for controlling quantum devices. Finally, we present simulation results that describe the expected system-level behavior of high-performance computing systems composed from compute nodes with quantum processing units. We describe performance for these hybrid systems in terms of time-to-solution, accuracy, and energy consumption, and we use simple application examples to estimate the performance advantage of quantum acceleration.

Investigations on electron beam evaporated Cu(In{sub 0.85}Ga{sub 0.15})Se{sub 2} thin film solar cells

Energy Technology Data Exchange (ETDEWEB)

Venkatachalam, M.; Kannan, M.D.; Prasanna, S.; Jayakumar, S.; Balasundaraprabhu, R. [Thin Film Center, Department of Physics, PSG College of Technology, Coimbatore (India); Muthukumarasamy, N. [Department of Physics, Coimbatore Institute of Technology, Coimbatore (India); Saroja, M. [Department of Electronics, Erode Arts College, Erode (India)

2009-09-15

CIGS bulk with composition of CuIn{sub 0.85}Ga{sub 0.15}Se{sub 2} was synthesized by direct reaction of elemental copper, indium, gallium and selenium. CIGS thin films were then deposited onto well-cleaned glass substrates using the prepared bulk alloy by electron beam deposition method. The structural properties of the deposited films were studied using X-ray diffraction technique. The as-deposited CIGS films were found to be amorphous. On annealing, the films crystallized with a tetragonal chalcopyrite structure. An intermediate Cu-rich phase precipitated at 200 C and dissociated at higher annealing temperatures. Average grain size calculated from the XRD spectra indicated that the films had a nano-crystalline structure and was further corroborated by AFM analysis of the sample surface. The chemical constituents present in the deposited CIGS films were identified using energy dispersive X-ray analysis. CIGS based solar cells were then fabricated on molybdenum and ITO coated glass substrates and the efficiencies have been evaluated. (author)

Controlling morphology and crystallite size of Cu(In{sub 0.7}Ga{sub 0.3})Se{sub 2} nano-crystals synthesized using a heating-up method

Energy Technology Data Exchange (ETDEWEB)

Hsu, Wei-Hsiang [Department of Resources Engineering, Particulate Materials Research Center, National Cheng Kung University, Tainan, 70101 Taiwan (China); Hsiang, Hsing-I, E-mail: hsingi@mail.ncku.edu.tw [Department of Resources Engineering, Particulate Materials Research Center, National Cheng Kung University, Tainan, 70101 Taiwan (China); Chia, Chih-Ta [Department of Physics, National Taiwan Normal University, Taipei, 116 Taiwan (China); Yen, Fu-Su [Department of Resources Engineering, Particulate Materials Research Center, National Cheng Kung University, Tainan, 70101 Taiwan (China)

2013-12-15

CuIn{sub 0.7}Ga{sub 0.3}Se{sub 2}(CIGS) nano-crystals were successfully synthesized via a heating-up process. The non-coordinating solvent (1-octadecene) and selenium/cations ratio effects on the crystalline phase and crystallite size of CIGS nano-crystallites were investigated. It was observed that the CIGS nano-crystallite morphology changed from sheet into spherical shape as the amount of 1-octadecene addition was increased. CIGS nano-crystals were obtained in 9–20 nm sizes as the selenium/cations ratio increased. These results suggest that the monomer reactivity in the solution can be adjusted by changing the solvent type and selenium/cations ratio, hence affecting the crystallite size and distribution. - Graphical abstract: CuIn{sub 0.7}Ga{sub 0.3}Se{sub 2}(CIGS) nano-crystals were successfully synthesized via a heating-up process in this study. The super-saturation in the solution can be adjusted by changing the OLA/ODE ratio and selenium/cation ratio.

Controlling morphology and crystallite size of Cu(In0.7Ga0.3)Se2 nano-crystals synthesized using a heating-up method

International Nuclear Information System (INIS)

Hsu, Wei-Hsiang; Hsiang, Hsing-I; Chia, Chih-Ta; Yen, Fu-Su

2013-01-01

CuIn 0.7 Ga 0.3 Se 2 (CIGS) nano-crystals were successfully synthesized via a heating-up process. The non-coordinating solvent (1-octadecene) and selenium/cations ratio effects on the crystalline phase and crystallite size of CIGS nano-crystallites were investigated. It was observed that the CIGS nano-crystallite morphology changed from sheet into spherical shape as the amount of 1-octadecene addition was increased. CIGS nano-crystals were obtained in 9–20 nm sizes as the selenium/cations ratio increased. These results suggest that the monomer reactivity in the solution can be adjusted by changing the solvent type and selenium/cations ratio, hence affecting the crystallite size and distribution. - Graphical abstract: CuIn 0.7 Ga 0.3 Se 2 (CIGS) nano-crystals were successfully synthesized via a heating-up process in this study. The super-saturation in the solution can be adjusted by changing the OLA/ODE ratio and selenium/cation ratio.

High Performance Commercial Fenestration Framing Systems

Energy Technology Data Exchange (ETDEWEB)

Mike Manteghi; Sneh Kumar; Joshua Early; Bhaskar Adusumalli

2010-01-31

A major objective of the U.S. Department of Energy is to have a zero energy commercial building by the year 2025. Windows have a major influence on the energy performance of the building envelope as they control over 55% of building energy load, and represent one important area where technologies can be developed to save energy. Aluminum framing systems are used in over 80% of commercial fenestration products (i.e. windows, curtain walls, store fronts, etc.). Aluminum framing systems are often required in commercial buildings because of their inherent good structural properties and long service life, which is required from commercial and architectural frames. At the same time, they are lightweight and durable, requiring very little maintenance, and offer design flexibility. An additional benefit of aluminum framing systems is their relatively low cost and easy manufacturability. Aluminum, being an easily recyclable material, also offers sustainable features. However, from energy efficiency point of view, aluminum frames have lower thermal performance due to the very high thermal conductivity of aluminum. Fenestration systems constructed of aluminum alloys therefore have lower performance in terms of being effective barrier to energy transfer (heat loss or gain). Despite the lower energy performance, aluminum is the choice material for commercial framing systems and dominates the commercial/architectural fenestration market because of the reasons mentioned above. In addition, there is no other cost effective and energy efficient replacement material available to take place of aluminum in the commercial/architectural market. Hence it is imperative to improve the performance of aluminum framing system to improve the energy performance of commercial fenestration system and in turn reduce the energy consumption of commercial building and achieve zero energy building by 2025. The objective of this project was to develop high performance, energy efficient commercial

High-Performance Management Practices and Employee Outcomes in Denmark

DEFF Research Database (Denmark)

Cristini, Annalisa; Eriksson, Tor; Pozzoli, Dario

High-performance work practices are frequently considered to have positive effects on corporate performance, but what do they do for employees? After showing that organizational innovation is indeed positively associated with firm performance, we investigate whether high-involvement work practices...

Optical interconnection networks for high-performance computing systems

International Nuclear Information System (INIS)

Biberman, Aleksandr; Bergman, Keren

2012-01-01

Enabled by silicon photonic technology, optical interconnection networks have the potential to be a key disruptive technology in computing and communication industries. The enduring pursuit of performance gains in computing, combined with stringent power constraints, has fostered the ever-growing computational parallelism associated with chip multiprocessors, memory systems, high-performance computing systems and data centers. Sustaining these parallelism growths introduces unique challenges for on- and off-chip communications, shifting the focus toward novel and fundamentally different communication approaches. Chip-scale photonic interconnection networks, enabled by high-performance silicon photonic devices, offer unprecedented bandwidth scalability with reduced power consumption. We demonstrate that the silicon photonic platforms have already produced all the high-performance photonic devices required to realize these types of networks. Through extensive empirical characterization in much of our work, we demonstrate such feasibility of waveguides, modulators, switches and photodetectors. We also demonstrate systems that simultaneously combine many functionalities to achieve more complex building blocks. We propose novel silicon photonic devices, subsystems, network topologies and architectures to enable unprecedented performance of these photonic interconnection networks. Furthermore, the advantages of photonic interconnection networks extend far beyond the chip, offering advanced communication environments for memory systems, high-performance computing systems, and data centers. (review article)

High-performance, stretchable, wire-shaped supercapacitors.

Science.gov (United States)

Chen, Tao; Hao, Rui; Peng, Huisheng; Dai, Liming

2015-01-07

A general approach toward extremely stretchable and highly conductive electrodes was developed. The method involves wrapping a continuous carbon nanotube (CNT) thin film around pre-stretched elastic wires, from which high-performance, stretchable wire-shaped supercapacitors were fabricated. The supercapacitors were made by twisting two such CNT-wrapped elastic wires, pre-coated with poly(vinyl alcohol)/H3PO4 hydrogel, as the electrolyte and separator. The resultant wire-shaped supercapacitors exhibited an extremely high elasticity of up to 350% strain with a high device capacitance up to 30.7 F g(-1), which is two times that of the state-of-the-art stretchable supercapacitor under only 100% strain. The wire-shaped structure facilitated the integration of multiple supercapacitors into a single wire device to meet specific energy and power needs for various potential applications. These supercapacitors can be repeatedly stretched from 0 to 200% strain for hundreds of cycles with no change in performance, thus outperforming all the reported state-of-the-art stretchable electronics. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fabrication and Characterization of Thin Film Solar Cell Made from CuIn0.75Ga0.25S2 Wurtzite Nanoparticles

Directory of Open Access Journals (Sweden)

Fengyan Zhang

2013-01-01

Full Text Available CuIn0.75Ga0.25S2 (CIGS thin film solar cells have been successfully fabricated using CIGS Wurtzite phase nanoparticles for the first time. The structure of the cell is Glass/Mo/CIGS/CdS/ZnO/ZnO:Al/Ag. The light absorption layer is made from CIGS Wurtzite phase nanoparticles that are formed from single-source precursors through a microwave irradiation. The Wurtzite phase nanoparticles were converted to Chalcopyrite phase film through a single-step annealing process in the presence of argon and sulfur at 450°C. The solar cell made from Wurtzite phase nanoparticles showed 1.6% efficiency and 0.42 fill factor.

High Performance Computing in Science and Engineering '14

CERN Document Server

Kröner, Dietmar; Resch, Michael

2015-01-01

This book presents the state-of-the-art in supercomputer simulation. It includes the latest findings from leading researchers using systems from the High Performance Computing Center Stuttgart (HLRS). The reports cover all fields of computational science and engineering ranging from CFD to computational physics and from chemistry to computer science with a special emphasis on industrially relevant applications. Presenting findings of one of Europe’s leading systems, this volume covers a wide variety of applications that deliver a high level of sustained performance. The book covers the main methods in high-performance computing. Its outstanding results in achieving the best performance for production codes are of particular interest for both scientists and   engineers. The book comes with a wealth of color illustrations and tables of results.  

Effects of potassium on kesterite solar cells: Similarities, differences and synergies with sodium

Directory of Open Access Journals (Sweden)

S. G. Haass

2018-01-01

Full Text Available Addition of alkali dopants is essential for achieving high-efficiency conversion efficiency of thin film solar cells based on chalcogenide semiconductors like Cu(In,GaSe2 (CIGS and Cu2ZnSn(S,Se4 (CZTSSe also called kesterite. Whereas the treatment with potassium allows boosting the performance of CIGS solar cells as compared to the conventional sodium doping, it is debated if similar effects can be expected for kesterite solar cells. Here the influence of potassium is investigated by introducing the dopant during the solution processing of kesterite absorbers. It is confirmed that the presence of potassium leads to an enhanced grain growth and a ten-fold lower potassium concentration is sufficient for obtaining grain size similar to sodium-containing absorbers. Potassium is located predominantly at grain boundaries and it suppresses incorporation of sodium into the absorber layer. The potassium doping increases the apparent carrier concentration to ∼2×1016 cm-3 for a potassium concentration of 0.2 at%. The potassium-doped solar cells yield conversion efficiency close to 10%, on par with only sodium-doped samples. Co-doping with potassium and sodium has not revealed any beneficial synergetic effects and it is concluded that both dopants exhibit similar effects on the kesterite solar cell performance.

Department of Energy research in utilization of high-performance computers

International Nuclear Information System (INIS)

Buzbee, B.L.; Worlton, W.J.; Michael, G.; Rodrigue, G.

1980-08-01

Department of Energy (DOE) and other Government research laboratories depend on high-performance computer systems to accomplish their programmatic goals. As the most powerful computer systems become available, they are acquired by these laboratories so that advances can be made in their disciplines. These advances are often the result of added sophistication to numerical models, the execution of which is made possible by high-performance computer systems. However, high-performance computer systems have become increasingly complex, and consequently it has become increasingly difficult to realize their potential performance. The result is a need for research on issues related to the utilization of these systems. This report gives a brief description of high-performance computers, and then addresses the use of and future needs for high-performance computers within DOE, the growing complexity of applications within DOE, and areas of high-performance computer systems warranting research. 1 figure

Mechanical Properties of High Performance Cementitious Grout (II)

DEFF Research Database (Denmark)

Sørensen, Eigil V.

The present report is an update of the report “Mechanical Properties of High Performance Cementitious Grout (I)” [1] and describes tests carried out on the high performance grout MASTERFLOW 9500, marked “WMG 7145 FP”, developed by BASF Construction Chemicals A/S and designed for use in grouted...

In-Situ Probing Plasmonic Energy Transfer in Cu(In, Ga)Se2 Solar Cells by Ultrabroadband Femtosecond Pump-Probe Spectroscopy.

Science.gov (United States)

Chen, Shih-Chen; Wu, Kaung-Hsiung; Li, Jia-Xing; Yabushita, Atsushi; Tang, Shih-Han; Luo, Chih Wei; Juang, Jenh-Yih; Kuo, Hao-Chung; Chueh, Yu-Lun

2015-12-18

In this work, we demonstrated a viable experimental scheme for in-situ probing the effects of Au nanoparticles (NPs) incorporation on plasmonic energy transfer in Cu(In, Ga)Se2 (CIGS) solar cells by elaborately analyzing the lifetimes and zero moment for hot carrier relaxation with ultrabroadband femtosecond pump-probe spectroscopy. The signals of enhanced photobleach (PB) and waned photoinduced absorption (PIA) attributable to surface plasmon resonance (SPR) of Au NPs were in-situ probed in transient differential absorption spectra. The results suggested that substantial carriers can be excited from ground state to lower excitation energy levels, which can reach thermalization much faster with the existence of SPR. Thus, direct electron transfer (DET) could be implemented to enhance the photocurrent of CIGS solar cells. Furthermore, based on the extracted hot carrier lifetimes, it was confirmed that the improved electrical transport might have been resulted primarily from the reduction in the surface recombination of photoinduced carriers through enhanced local electromagnetic field (LEMF). Finally, theoretical calculation for resonant energy transfer (RET)-induced enhancement in the probability of exciting electron-hole pairs was conducted and the results agreed well with the enhanced PB peak of transient differential absorption in plasmonic CIGS film. These results indicate that plasmonic energy transfer is a viable approach to boost high-efficiency CIGS solar cells.

Cytotoxicity of semiconductor nanoparticles in A549 cells is attributable to their intrinsic oxidant activity

Energy Technology Data Exchange (ETDEWEB)

Escamilla-Rivera, Vicente; Uribe-Ramirez, Marisela [Centro de Investigación y de Estudios Avanzados del IPN (CINVESTAV-IPN), Departamento de Toxicología (Mexico); Gonzalez-Pozos, Sirenia [CINVESTAV-IPN, Unidad de Microscopia Electrónica (LaNSE) (Mexico); Velumani, Subramaniam [CINVESTAV-IPN, Departamento de Ingeniería Eléctrica (Mexico); Arreola-Mendoza, Laura [Centro Interdisciplinario de Investigaciones y Estudios sobre Medio Ambiente y Desarrollo del Instituto Politécnico Nacional (CIIEMAD-IPN), Departamento de Biociencias e Ingeniería (Mexico); Vizcaya-Ruiz, Andrea De, E-mail: avizcaya@cinvestav.mx [Centro de Investigación y de Estudios Avanzados del IPN (CINVESTAV-IPN), Departamento de Toxicología (Mexico)

2016-04-15

Copper indium gallium diselenide (CIGS) and cadmium sulfide (CdS) nanoparticles (NP) are next generation semiconductors used in photovoltaic cells (PV). They possess high quantum efficiency, absorption coefficient, and cheaper manufacturing costs compared to silicon. Due to their potential for an industrial development and the lack of information about the risk associated in their use, we investigated the influence of the physicochemical characteristics of CIGS (9 nm) and CdS (20 nm) in relation to the induction of cytotoxicity in human alveolar A549 cells through ROS generation and mitochondrial dysfunction. CIGS induced cytotoxicity in a dose dependent manner in lower concentrations than CdS; both NP were able to induce ROS in A549. Moreover, CIGS interact directly with mitochondria inducing depolarization that leads to the induction of apoptosis compared to CdS. Antioxidant pretreatment significantly prevented the loss of mitochondrial membrane potential and cytotoxicity, suggesting ROS generation as the main cytotoxic mechanism. These results demonstrate that semiconductor characteristics of NP are crucial for the type and intensity of the cytotoxic effects. Our work provides relevant information that may help guide the production of a safer NP-based PV technologies, and would be a valuable resource on future risk assessment for a safer use of nanotechnology in the development of clean sources of renewable energy.

A Linux Workstation for High Performance Graphics

Science.gov (United States)

Geist, Robert; Westall, James

2000-01-01

The primary goal of this effort was to provide a low-cost method of obtaining high-performance 3-D graphics using an industry standard library (OpenGL) on PC class computers. Previously, users interested in doing substantial visualization or graphical manipulation were constrained to using specialized, custom hardware most often found in computers from Silicon Graphics (SGI). We provided an alternative to expensive SGI hardware by taking advantage of third-party, 3-D graphics accelerators that have now become available at very affordable prices. To make use of this hardware our goal was to provide a free, redistributable, and fully-compatible OpenGL work-alike library so that existing bodies of code could simply be recompiled. for PC class machines running a free version of Unix. This should allow substantial cost savings while greatly expanding the population of people with access to a serious graphics development and viewing environment. This should offer a means for NASA to provide a spectrum of graphics performance to its scientists, supplying high-end specialized SGI hardware for high-performance visualization while fulfilling the requirements of medium and lower performance applications with generic, off-the-shelf components and still maintaining compatibility between the two.

Strategies and Experiences Using High Performance Fortran

National Research Council Canada - National Science Library

Shires, Dale

2001-01-01

.... High performance Fortran (HPF) is a relative new addition to the Fortran dialect It is an attempt to provide an efficient high-level Fortran parallel programming language for the latest generation of been debatable...

Prevalence and characteristics of e-cigarette use among adults in Malaysia

OpenAIRE

Jamalludin Ab Rahman; Mohamad Haniki Nik Mohamed; Muhammad Fadhli Mohd Yusoff; Norny Syafinaz Ab Rahman; Samsul Draman; Mira Kartiwi; Balkish Mahadir; Tahir Aris

2018-01-01

Background E-cigarette (e-cig) use has become a worldwide phenomenon since 2010. This study aims to determine the prevalence of e-cig use, distribution and characteristics among Malaysian adults. Malaysia is a typical Asian country. The results of this study will provide evidence for policy makers to formulate appropriate measures towards regulation of e-cig in Malaysia and can become a reference for other similar countries. Methods Complex sampling design was...

High performance anode for advanced Li batteries

Energy Technology Data Exchange (ETDEWEB)

Lake, Carla [Applied Sciences, Inc., Cedarville, OH (United States)

2015-11-02

The overall objective of this Phase I SBIR effort was to advance the manufacturing technology for ASI’s Si-CNF high-performance anode by creating a framework for large volume production and utilization of low-cost Si-coated carbon nanofibers (Si-CNF) for the battery industry. This project explores the use of nano-structured silicon which is deposited on a nano-scale carbon filament to achieve the benefits of high cycle life and high charge capacity without the consequent fading of, or failure in the capacity resulting from stress-induced fracturing of the Si particles and de-coupling from the electrode. ASI’s patented coating process distinguishes itself from others, in that it is highly reproducible, readily scalable and results in a Si-CNF composite structure containing 25-30% silicon, with a compositionally graded interface at the Si-CNF interface that significantly improve cycling stability and enhances adhesion of silicon to the carbon fiber support. In Phase I, the team demonstrated the production of the Si-CNF anode material can successfully be transitioned from a static bench-scale reactor into a fluidized bed reactor. In addition, ASI made significant progress in the development of low cost, quick testing methods which can be performed on silicon coated CNFs as a means of quality control. To date, weight change, density, and cycling performance were the key metrics used to validate the high performance anode material. Under this effort, ASI made strides to establish a quality control protocol for the large volume production of Si-CNFs and has identified several key technical thrusts for future work. Using the results of this Phase I effort as a foundation, ASI has defined a path forward to commercialize and deliver high volume and low-cost production of SI-CNF material for anodes in Li-ion batteries.

Evaluation of high-performance computing software

Energy Technology Data Exchange (ETDEWEB)

Browne, S.; Dongarra, J. [Univ. of Tennessee, Knoxville, TN (United States); Rowan, T. [Oak Ridge National Lab., TN (United States)

1996-12-31

The absence of unbiased and up to date comparative evaluations of high-performance computing software complicates a user`s search for the appropriate software package. The National HPCC Software Exchange (NHSE) is attacking this problem using an approach that includes independent evaluations of software, incorporation of author and user feedback into the evaluations, and Web access to the evaluations. We are applying this approach to the Parallel Tools Library (PTLIB), a new software repository for parallel systems software and tools, and HPC-Netlib, a high performance branch of the Netlib mathematical software repository. Updating the evaluations with feed-back and making it available via the Web helps ensure accuracy and timeliness, and using independent reviewers produces unbiased comparative evaluations difficult to find elsewhere.

High Performance Proactive Digital Forensics

International Nuclear Information System (INIS)

Alharbi, Soltan; Traore, Issa; Moa, Belaid; Weber-Jahnke, Jens

2012-01-01

With the increase in the number of digital crimes and in their sophistication, High Performance Computing (HPC) is becoming a must in Digital Forensics (DF). According to the FBI annual report, the size of data processed during the 2010 fiscal year reached 3,086 TB (compared to 2,334 TB in 2009) and the number of agencies that requested Regional Computer Forensics Laboratory assistance increasing from 689 in 2009 to 722 in 2010. Since most investigation tools are both I/O and CPU bound, the next-generation DF tools are required to be distributed and offer HPC capabilities. The need for HPC is even more evident in investigating crimes on clouds or when proactive DF analysis and on-site investigation, requiring semi-real time processing, are performed. Although overcoming the performance challenge is a major goal in DF, as far as we know, there is almost no research on HPC-DF except for few papers. As such, in this work, we extend our work on the need of a proactive system and present a high performance automated proactive digital forensic system. The most expensive phase of the system, namely proactive analysis and detection, uses a parallel extension of the iterative z algorithm. It also implements new parallel information-based outlier detection algorithms to proactively and forensically handle suspicious activities. To analyse a large number of targets and events and continuously do so (to capture the dynamics of the system), we rely on a multi-resolution approach to explore the digital forensic space. Data set from the Honeynet Forensic Challenge in 2001 is used to evaluate the system from DF and HPC perspectives.

Characterization of in-situ annealed sub-micron thick Cu(In,Ga)Se{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Ko, Byoung-Soo; Sung, Shi-Joon; Hwang, Dae-Kue, E-mail: dkhwang@dgist.ac.kr

2015-09-01

Sub-micron thick Cu(In,Ga)Se{sub 2} (CIGS) thin films were deposited on Mo-coated soda-lime glass substrates under various conditions by single-stage co-evaporation. Generally, the short circuit current (J{sub sc}) decreased with the decreasing thickness of the absorber layer. However, in this study, J{sub sc} was nearly unchanged with decreasing thickness, while the open circuit voltage (V{sub oc}) and fill factor (FF) decreased by 31.9 and 31.1%, respectively. We believe that the remarkable change of V{sub oc} and FF can be attributed to the difference in the total amount of injected thermal energy. Using scanning electron microscopy, we confirmed that the surface morphology becomes smooth and the grain size increased after the annealing process. In the X-ray diffraction patterns, the CIGS thin film also showed an improved crystal quality. We observed that the electric properties were improved by the in-situ annealing of CIGS thin films. The reverse saturation current density of the annealed CIGS solar cell was 100 times smaller than that of reference solar cell. Thus, sub-micron CIGS thin films annealed under a constant Se rate showed a 64.7% improvement in efficiency. - Highlights: • The effects of in-situ annealing the sub-micron CIGS film have been investigated. • The surface morphology and the grain size were improved by in-situ annealing. • The V{sub oc} and FF of the films were increased by about 30% after in-situ annealing. • In-situ annealing of sub-micron thick CIGS films can be improved an efficiency.

Sex Differences in Mathematics Performance among Senior High ...

African Journals Online (AJOL)

This study explored sex differences in mathematics performance of students in the final year of high school and changes in these differences over a 3-year period in Ghana. A convenience sample of 182 students, 109 boys and 72 girls in three high schools in Ghana was used. Mathematics performance was assessed using ...

Embedded High Performance Scalable Computing Systems

National Research Council Canada - National Science Library

Ngo, David

2003-01-01

The Embedded High Performance Scalable Computing Systems (EHPSCS) program is a cooperative agreement between Sanders, A Lockheed Martin Company and DARPA that ran for three years, from Apr 1995 - Apr 1998...

High-performance vertical organic transistors.

Science.gov (United States)

Kleemann, Hans; Günther, Alrun A; Leo, Karl; Lüssem, Björn

2013-11-11

Vertical organic thin-film transistors (VOTFTs) are promising devices to overcome the transconductance and cut-off frequency restrictions of horizontal organic thin-film transistors. The basic physical mechanisms of VOTFT operation, however, are not well understood and VOTFTs often require complex patterning techniques using self-assembly processes which impedes a future large-area production. In this contribution, high-performance vertical organic transistors comprising pentacene for p-type operation and C60 for n-type operation are presented. The static current-voltage behavior as well as the fundamental scaling laws of such transistors are studied, disclosing a remarkable transistor operation with a behavior limited by injection of charge carriers. The transistors are manufactured by photolithography, in contrast to other VOTFT concepts using self-assembled source electrodes. Fluorinated photoresist and solvent compounds allow for photolithographical patterning directly and strongly onto the organic materials, simplifying the fabrication protocol and making VOTFTs a prospective candidate for future high-performance applications of organic transistors. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High-performance non-volatile organic ferroelectric memory on banknotes

KAUST Repository

Khan, Yasser; Bhansali, Unnat Sampatraj; Alshareef, Husam N.

2012-01-01

High-performance non-volatile polymer ferroelectric memory are fabricated on banknotes using poly(vinylidene fluoride trifluoroethylene). The devices show excellent performance with high remnant polarization, low operating voltages, low leakage

High-performance non-volatile organic ferroelectric memory on banknotes

KAUST Repository

Khan, Yasser

2012-03-21

High-performance non-volatile polymer ferroelectric memory are fabricated on banknotes using poly(vinylidene fluoride trifluoroethylene). The devices show excellent performance with high remnant polarization, low operating voltages, low leakage, high mobility, and long retention times. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High-performance non-volatile organic ferroelectric memory on banknotes.

Science.gov (United States)

Khan, M A; Bhansali, Unnat S; Alshareef, H N

2012-04-24

High-performance non-volatile polymer ferroelectric memory are fabricated on banknotes using poly(vinylidene fluoride trifluoroethylene). The devices show excellent performance with high remnant polarization, low operating voltages, low leakage, high mobility, and long retention times. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

THE RELATION OF HIGH-PERFORMANCE WORK SYSTEMS WITH EMPLOYEE INVOLVEMENT

Directory of Open Access Journals (Sweden)

Bilal AFSAR

2010-01-01

Full Text Available The basic aim of high performance work systems is to enable employees to exercise decision making, leading to flexibility, innovation, improvement and skill sharing. By facilitating the development of high performance work systems we help organizations make continuous improvement a way of life.The notion of a high-performance work system (HPWS constitutes a claim that there exists a system of work practices for core workers in an organisation that leads in some way to superior performance. This article will discuss the relation that HPWS has with the improvement of firms’ performance and high involvement of the employees.

Contemporary high performance computing from petascale toward exascale

CERN Document Server

Vetter, Jeffrey S

2013-01-01

Contemporary High Performance Computing: From Petascale toward Exascale focuses on the ecosystems surrounding the world's leading centers for high performance computing (HPC). It covers many of the important factors involved in each ecosystem: computer architectures, software, applications, facilities, and sponsors. The first part of the book examines significant trends in HPC systems, including computer architectures, applications, performance, and software. It discusses the growth from terascale to petascale computing and the influence of the TOP500 and Green500 lists. The second part of the

Pengaruh High Performance Work Practice (Hpwp) Terhadap Job Performance Pada Frontliner Bank

OpenAIRE

Ihdaryanti, Monica Amani; Panggabean, Mutiara S

2014-01-01

Generally High Performance Work Practice (HPWP) is a part of management human resources. The objectives of this research are getting and analyzing the effect of HPWPs with Job Satisfaction; HPWPs with Organizational Commitment; Job Satisfaction with Organizational Commitment; Job Satisfaction with Job Performance; and Organizational Commitment with Job Performance. The total of sample in this research is 100 respondents which are as Front liner BNI and Mandiri. The result of th...

High performance liquid chromatographic determination of ...

African Journals Online (AJOL)

STORAGESEVER

2010-02-08

) high performance liquid chromatography (HPLC) grade .... applications. These are important requirements if the reagent is to be applicable to on-line pre or post column derivatisation in a possible automation of the analytical.

Can Knowledge of the Characteristics of "High Performers" Be Generalised?

Science.gov (United States)

McKenna, Stephen

2002-01-01

Two managers described as high performing constructed complexity maps of their organization/world. The maps suggested that high performance is socially constructed and negotiated in specific contexts and management competencies associated with it are context specific. Development of high performers thus requires personalized coaching more than…

Comparing Dutch and British high performing managers

NARCIS (Netherlands)

Waal, A.A. de; Heijden, B.I.J.M. van der; Selvarajah, C.; Meyer, D.

2016-01-01

National cultures have a strong influence on the performance of organizations and should be taken into account when studying the traits of high performing managers. At the same time, many studies that focus upon the attributes of successful managers show that there are attributes that are similar

Advances in Cost-Efficient Thin-Film Photovoltaics Based on Cu(In,Ga)Se2

OpenAIRE

Michael Powalla; Stefan Paetel; Dimitrios Hariskos; Roland Wuerz; Friedrich Kessler; Peter Lechner; Wiltraud Wischmann; Theresa Magorian Friedlmeier

2017-01-01

In this article, we discuss the leading thin-film photovoltaic (PV) technology based on the Cu(In,Ga)Se2 (CIGS) compound semiconductor. This contribution includes a general comparison with the conventional Si-wafer-based PV technology and discusses the basics of the CIGS technology as well as advances in world-record-level conversion efficiency, production, applications, stability, and future developments with respect to a flexible product. Once in large-scale mass production, the CIGS techno...

Micromagnetics on high-performance workstation and mobile computational platforms